diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt | 670 |
1 files changed, 670 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt new file mode 100644 index 000000000..d099f3476 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt @@ -0,0 +1,670 @@ +NVIDIA Tegra PCIe controller + +Required properties: +- compatible: Must be: + - "nvidia,tegra20-pcie": for Tegra20 + - "nvidia,tegra30-pcie": for Tegra30 + - "nvidia,tegra124-pcie": for Tegra124 and Tegra132 + - "nvidia,tegra210-pcie": for Tegra210 + - "nvidia,tegra186-pcie": for Tegra186 +- power-domains: To ungate power partition by BPMP powergate driver. Must + contain BPMP phandle and PCIe power partition ID. This is required only + for Tegra186. +- device_type: Must be "pci" +- reg: A list of physical base address and length for each set of controller + registers. Must contain an entry for each entry in the reg-names property. +- reg-names: Must include the following entries: + "pads": PADS registers + "afi": AFI registers + "cs": configuration space region +- interrupts: A list of interrupt outputs of the controller. Must contain an + entry for each entry in the interrupt-names property. +- interrupt-names: Must include the following entries: + "intr": The Tegra interrupt that is asserted for controller interrupts + "msi": The Tegra interrupt that is asserted when an MSI is received +- bus-range: Range of bus numbers associated with this controller +- #address-cells: Address representation for root ports (must be 3) + - cell 0 specifies the bus and device numbers of the root port: + [23:16]: bus number + [15:11]: device number + - cell 1 denotes the upper 32 address bits and should be 0 + - cell 2 contains the lower 32 address bits and is used to translate to the + CPU address space +- #size-cells: Size representation for root ports (must be 2) +- ranges: Describes the translation of addresses for root ports and standard + PCI regions. The entries must be 6 cells each, where the first three cells + correspond to the address as described for the #address-cells property + above, the fourth cell is the physical CPU address to translate to and the + fifth and six cells are as described for the #size-cells property above. + - The first two entries are expected to translate the addresses for the root + port registers, which are referenced by the assigned-addresses property of + the root port nodes (see below). + - The remaining entries setup the mapping for the standard I/O, memory and + prefetchable PCI regions. The first cell determines the type of region + that is setup: + - 0x81000000: I/O memory region + - 0x82000000: non-prefetchable memory region + - 0xc2000000: prefetchable memory region + Please refer to the standard PCI bus binding document for a more detailed + explanation. +- #interrupt-cells: Size representation for interrupts (must be 1) +- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties + Please refer to the standard PCI bus binding document for a more detailed + explanation. +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - pex + - afi + - pll_e + - cml (not required for Tegra20) +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - pex + - afi + - pcie_x + +Optional properties: +- pinctrl-names: A list of pinctrl state names. Must contain the following + entries: + - "default": active state, puts PCIe I/O out of deep power down state + - "idle": puts PCIe I/O into deep power down state +- pinctrl-0: phandle for the default/active state of pin configurations. +- pinctrl-1: phandle for the idle state of pin configurations. + +Required properties on Tegra124 and later (deprecated): +- phys: Must contain an entry for each entry in phy-names. +- phy-names: Must include the following entries: + - pcie + +These properties are deprecated in favour of per-lane PHYs define in each of +the root ports (see below). + +Power supplies for Tegra20: +- avdd-pex-supply: Power supply for analog PCIe logic. Must supply 1.05 V. +- vdd-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. +- avdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must + supply 1.05 V. +- avdd-plle-supply: Power supply for PLLE, which is shared with SATA. Must + supply 1.05 V. +- vddio-pex-clk-supply: Power supply for PCIe clock. Must supply 3.3 V. + +Power supplies for Tegra30: +- Required: + - avdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must + supply 1.05 V. + - avdd-plle-supply: Power supply for PLLE, which is shared with SATA. Must + supply 1.05 V. + - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must + supply 1.8 V. + - hvdd-pex-supply: High-voltage supply for PCIe I/O and PCIe output clocks. + Must supply 3.3 V. +- Optional: + - If lanes 0 to 3 are used: + - avdd-pexa-supply: Power supply for analog PCIe logic. Must supply 1.05 V. + - vdd-pexa-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. + - If lanes 4 or 5 are used: + - avdd-pexb-supply: Power supply for analog PCIe logic. Must supply 1.05 V. + - vdd-pexb-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. + +Power supplies for Tegra124: +- Required: + - avddio-pex-supply: Power supply for analog PCIe logic. Must supply 1.05 V. + - dvddio-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. + - hvdd-pex-supply: High-voltage supply for PCIe I/O and PCIe output clocks. + Must supply 3.3 V. + - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must + supply 2.8-3.3 V. + +Power supplies for Tegra210: +- Required: + - hvddio-pex-supply: High-voltage supply for PCIe I/O and PCIe output + clocks. Must supply 1.8 V. + - dvddio-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. + - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must + supply 1.8 V. + +Power supplies for Tegra186: +- Required: + - dvdd-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. + - hvdd-pex-pll-supply: High-voltage supply for PLLE (shared with USB3). Must + supply 1.8 V. + - hvdd-pex-supply: High-voltage supply for PCIe I/O and PCIe output clocks. + Must supply 1.8 V. + - vddio-pexctl-aud-supply: Power supply for PCIe side band signals. Must + supply 1.8 V. + +Root ports are defined as subnodes of the PCIe controller node. + +Required properties: +- device_type: Must be "pci" +- assigned-addresses: Address and size of the port configuration registers +- reg: PCI bus address of the root port +- #address-cells: Must be 3 +- #size-cells: Must be 2 +- ranges: Sub-ranges distributed from the PCIe controller node. An empty + property is sufficient. +- nvidia,num-lanes: Number of lanes to use for this port. Valid combinations + are: + - Root port 0 uses 4 lanes, root port 1 is unused. + - Both root ports use 2 lanes. + +Required properties for Tegra124 and later: +- phys: Must contain an phandle to a PHY for each entry in phy-names. +- phy-names: Must include an entry for each active lane. Note that the number + of entries does not have to (though usually will) be equal to the specified + number of lanes in the nvidia,num-lanes property. Entries are of the form + "pcie-N": where N ranges from 0 to the value specified in nvidia,num-lanes. + +Examples: +========= + +Tegra20: +-------- + +SoC DTSI: + + pcie-controller@80003000 { + compatible = "nvidia,tegra20-pcie"; + device_type = "pci"; + reg = <0x80003000 0x00000800 /* PADS registers */ + 0x80003800 0x00000200 /* AFI registers */ + 0x90000000 0x10000000>; /* configuration space */ + reg-names = "pads", "afi", "cs"; + interrupts = <0 98 0x04 /* controller interrupt */ + 0 99 0x04>; /* MSI interrupt */ + interrupt-names = "intr", "msi"; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &intc GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + + bus-range = <0x00 0xff>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x82000000 0 0x80000000 0x80000000 0 0x00001000 /* port 0 registers */ + 0x82000000 0 0x80001000 0x80001000 0 0x00001000 /* port 1 registers */ + 0x81000000 0 0 0x82000000 0 0x00010000 /* downstream I/O */ + 0x82000000 0 0xa0000000 0xa0000000 0 0x10000000 /* non-prefetchable memory */ + 0xc2000000 0 0xb0000000 0xb0000000 0 0x10000000>; /* prefetchable memory */ + + clocks = <&tegra_car 70>, <&tegra_car 72>, <&tegra_car 118>; + clock-names = "pex", "afi", "pll_e"; + resets = <&tegra_car 70>, <&tegra_car 72>, <&tegra_car 74>; + reset-names = "pex", "afi", "pcie_x"; + status = "disabled"; + + pci@1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x80000000 0 0x1000>; + reg = <0x000800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + + ranges; + + nvidia,num-lanes = <2>; + }; + + pci@2,0 { + device_type = "pci"; + assigned-addresses = <0x82001000 0 0x80001000 0 0x1000>; + reg = <0x001000 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + + ranges; + + nvidia,num-lanes = <2>; + }; + }; + +Board DTS: + + pcie-controller@80003000 { + status = "okay"; + + vdd-supply = <&pci_vdd_reg>; + pex-clk-supply = <&pci_clk_reg>; + + /* root port 00:01.0 */ + pci@1,0 { + status = "okay"; + + /* bridge 01:00.0 (optional) */ + pci@0,0 { + reg = <0x010000 0 0 0 0>; + + #address-cells = <3>; + #size-cells = <2>; + + device_type = "pci"; + + /* endpoint 02:00.0 */ + pci@0,0 { + reg = <0x020000 0 0 0 0>; + }; + }; + }; + }; + +Note that devices on the PCI bus are dynamically discovered using PCI's bus +enumeration and therefore don't need corresponding device nodes in DT. However +if a device on the PCI bus provides a non-probeable bus such as I2C or SPI, +device nodes need to be added in order to allow the bus' children to be +instantiated at the proper location in the operating system's device tree (as +illustrated by the optional nodes in the example above). + +Tegra30: +-------- + +SoC DTSI: + + pcie-controller@3000 { + compatible = "nvidia,tegra30-pcie"; + device_type = "pci"; + reg = <0x00003000 0x00000800 /* PADS registers */ + 0x00003800 0x00000200 /* AFI registers */ + 0x10000000 0x10000000>; /* configuration space */ + reg-names = "pads", "afi", "cs"; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH /* controller interrupt */ + GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */ + interrupt-names = "intr", "msi"; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &intc GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + + bus-range = <0x00 0xff>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x82000000 0 0x00000000 0x00000000 0 0x00001000 /* port 0 configuration space */ + 0x82000000 0 0x00001000 0x00001000 0 0x00001000 /* port 1 configuration space */ + 0x82000000 0 0x00004000 0x00004000 0 0x00001000 /* port 2 configuration space */ + 0x81000000 0 0 0x02000000 0 0x00010000 /* downstream I/O */ + 0x82000000 0 0x20000000 0x20000000 0 0x08000000 /* non-prefetchable memory */ + 0xc2000000 0 0x28000000 0x28000000 0 0x18000000>; /* prefetchable memory */ + + clocks = <&tegra_car TEGRA30_CLK_PCIE>, + <&tegra_car TEGRA30_CLK_AFI>, + <&tegra_car TEGRA30_CLK_PLL_E>, + <&tegra_car TEGRA30_CLK_CML0>; + clock-names = "pex", "afi", "pll_e", "cml"; + resets = <&tegra_car 70>, + <&tegra_car 72>, + <&tegra_car 74>; + reset-names = "pex", "afi", "pcie_x"; + status = "disabled"; + + pci@1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x00000000 0 0x1000>; + reg = <0x000800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <2>; + }; + + pci@2,0 { + device_type = "pci"; + assigned-addresses = <0x82001000 0 0x00001000 0 0x1000>; + reg = <0x001000 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <2>; + }; + + pci@3,0 { + device_type = "pci"; + assigned-addresses = <0x82001800 0 0x00004000 0 0x1000>; + reg = <0x001800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <2>; + }; + }; + +Board DTS: + + pcie-controller@3000 { + status = "okay"; + + avdd-pexa-supply = <&ldo1_reg>; + vdd-pexa-supply = <&ldo1_reg>; + avdd-pexb-supply = <&ldo1_reg>; + vdd-pexb-supply = <&ldo1_reg>; + avdd-pex-pll-supply = <&ldo1_reg>; + avdd-plle-supply = <&ldo1_reg>; + vddio-pex-ctl-supply = <&sys_3v3_reg>; + hvdd-pex-supply = <&sys_3v3_pexs_reg>; + + pci@1,0 { + status = "okay"; + }; + + pci@3,0 { + status = "okay"; + }; + }; + +Tegra124: +--------- + +SoC DTSI: + + pcie-controller@1003000 { + compatible = "nvidia,tegra124-pcie"; + device_type = "pci"; + reg = <0x0 0x01003000 0x0 0x00000800 /* PADS registers */ + 0x0 0x01003800 0x0 0x00000800 /* AFI registers */ + 0x0 0x02000000 0x0 0x10000000>; /* configuration space */ + reg-names = "pads", "afi", "cs"; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */ + <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */ + interrupt-names = "intr", "msi"; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + + bus-range = <0x00 0xff>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x82000000 0 0x01000000 0x0 0x01000000 0 0x00001000 /* port 0 configuration space */ + 0x82000000 0 0x01001000 0x0 0x01001000 0 0x00001000 /* port 1 configuration space */ + 0x81000000 0 0x0 0x0 0x12000000 0 0x00010000 /* downstream I/O (64 KiB) */ + 0x82000000 0 0x13000000 0x0 0x13000000 0 0x0d000000 /* non-prefetchable memory (208 MiB) */ + 0xc2000000 0 0x20000000 0x0 0x20000000 0 0x20000000>; /* prefetchable memory (512 MiB) */ + + clocks = <&tegra_car TEGRA124_CLK_PCIE>, + <&tegra_car TEGRA124_CLK_AFI>, + <&tegra_car TEGRA124_CLK_PLL_E>, + <&tegra_car TEGRA124_CLK_CML0>; + clock-names = "pex", "afi", "pll_e", "cml"; + resets = <&tegra_car 70>, + <&tegra_car 72>, + <&tegra_car 74>; + reset-names = "pex", "afi", "pcie_x"; + status = "disabled"; + + pci@1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x01000000 0 0x1000>; + reg = <0x000800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <2>; + }; + + pci@2,0 { + device_type = "pci"; + assigned-addresses = <0x82001000 0 0x01001000 0 0x1000>; + reg = <0x001000 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <1>; + }; + }; + +Board DTS: + + pcie-controller@1003000 { + status = "okay"; + + avddio-pex-supply = <&vdd_1v05_run>; + dvddio-pex-supply = <&vdd_1v05_run>; + avdd-pex-pll-supply = <&vdd_1v05_run>; + hvdd-pex-supply = <&vdd_3v3_lp0>; + hvdd-pex-pll-e-supply = <&vdd_3v3_lp0>; + vddio-pex-ctl-supply = <&vdd_3v3_lp0>; + avdd-pll-erefe-supply = <&avdd_1v05_run>; + + /* Mini PCIe */ + pci@1,0 { + phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-4}>; + phy-names = "pcie-0"; + status = "okay"; + }; + + /* Gigabit Ethernet */ + pci@2,0 { + phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-2}>; + phy-names = "pcie-0"; + status = "okay"; + }; + }; + +Tegra210: +--------- + +SoC DTSI: + + pcie-controller@1003000 { + compatible = "nvidia,tegra210-pcie"; + device_type = "pci"; + reg = <0x0 0x01003000 0x0 0x00000800 /* PADS registers */ + 0x0 0x01003800 0x0 0x00000800 /* AFI registers */ + 0x0 0x02000000 0x0 0x10000000>; /* configuration space */ + reg-names = "pads", "afi", "cs"; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */ + <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */ + interrupt-names = "intr", "msi"; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + + bus-range = <0x00 0xff>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x82000000 0 0x01000000 0x0 0x01000000 0 0x00001000 /* port 0 configuration space */ + 0x82000000 0 0x01001000 0x0 0x01001000 0 0x00001000 /* port 1 configuration space */ + 0x81000000 0 0x0 0x0 0x12000000 0 0x00010000 /* downstream I/O (64 KiB) */ + 0x82000000 0 0x13000000 0x0 0x13000000 0 0x0d000000 /* non-prefetchable memory (208 MiB) */ + 0xc2000000 0 0x20000000 0x0 0x20000000 0 0x20000000>; /* prefetchable memory (512 MiB) */ + + clocks = <&tegra_car TEGRA210_CLK_PCIE>, + <&tegra_car TEGRA210_CLK_AFI>, + <&tegra_car TEGRA210_CLK_PLL_E>, + <&tegra_car TEGRA210_CLK_CML0>; + clock-names = "pex", "afi", "pll_e", "cml"; + resets = <&tegra_car 70>, + <&tegra_car 72>, + <&tegra_car 74>; + reset-names = "pex", "afi", "pcie_x"; + status = "disabled"; + + pci@1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x01000000 0 0x1000>; + reg = <0x000800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <4>; + }; + + pci@2,0 { + device_type = "pci"; + assigned-addresses = <0x82001000 0 0x01001000 0 0x1000>; + reg = <0x001000 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <1>; + }; + }; + +Board DTS: + + pcie-controller@1003000 { + status = "okay"; + + avdd-pll-uerefe-supply = <&avdd_1v05_pll>; + hvddio-pex-supply = <&vdd_1v8>; + dvddio-pex-supply = <&vdd_pex_1v05>; + dvdd-pex-pll-supply = <&vdd_pex_1v05>; + hvdd-pex-pll-e-supply = <&vdd_1v8>; + vddio-pex-ctl-supply = <&vdd_1v8>; + + pci@1,0 { + phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-0}>, + <&{/padctl@7009f000/pads/pcie/lanes/pcie-1}>, + <&{/padctl@7009f000/pads/pcie/lanes/pcie-2}>, + <&{/padctl@7009f000/pads/pcie/lanes/pcie-3}>; + phy-names = "pcie-0", "pcie-1", "pcie-2", "pcie-3"; + status = "okay"; + }; + + pci@2,0 { + phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-4}>; + phy-names = "pcie-0"; + status = "okay"; + }; + }; + +Tegra186: +--------- + +SoC DTSI: + + pcie@10003000 { + compatible = "nvidia,tegra186-pcie"; + power-domains = <&bpmp TEGRA186_POWER_DOMAIN_PCX>; + device_type = "pci"; + reg = <0x0 0x10003000 0x0 0x00000800 /* PADS registers */ + 0x0 0x10003800 0x0 0x00000800 /* AFI registers */ + 0x0 0x40000000 0x0 0x10000000>; /* configuration space */ + reg-names = "pads", "afi", "cs"; + + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */ + <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */ + interrupt-names = "intr", "msi"; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; + + bus-range = <0x00 0xff>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x82000000 0 0x10000000 0x0 0x10000000 0 0x00001000 /* port 0 configuration space */ + 0x82000000 0 0x10001000 0x0 0x10001000 0 0x00001000 /* port 1 configuration space */ + 0x82000000 0 0x10004000 0x0 0x10004000 0 0x00001000 /* port 2 configuration space */ + 0x81000000 0 0x0 0x0 0x50000000 0 0x00010000 /* downstream I/O (64 KiB) */ + 0x82000000 0 0x50100000 0x0 0x50100000 0 0x07F00000 /* non-prefetchable memory (127 MiB) */ + 0xc2000000 0 0x58000000 0x0 0x58000000 0 0x28000000>; /* prefetchable memory (640 MiB) */ + + clocks = <&bpmp TEGRA186_CLK_AFI>, + <&bpmp TEGRA186_CLK_PCIE>, + <&bpmp TEGRA186_CLK_PLLE>; + clock-names = "afi", "pex", "pll_e"; + + resets = <&bpmp TEGRA186_RESET_AFI>, + <&bpmp TEGRA186_RESET_PCIE>, + <&bpmp TEGRA186_RESET_PCIEXCLK>; + reset-names = "afi", "pex", "pcie_x"; + + status = "disabled"; + + pci@1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x10000000 0 0x1000>; + reg = <0x000800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <2>; + }; + + pci@2,0 { + device_type = "pci"; + assigned-addresses = <0x82001000 0 0x10001000 0 0x1000>; + reg = <0x001000 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <1>; + }; + + pci@3,0 { + device_type = "pci"; + assigned-addresses = <0x82001800 0 0x10004000 0 0x1000>; + reg = <0x001800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <1>; + }; + }; + +Board DTS: + + pcie@10003000 { + status = "okay"; + + dvdd-pex-supply = <&vdd_pex>; + hvdd-pex-pll-supply = <&vdd_1v8>; + hvdd-pex-supply = <&vdd_1v8>; + vddio-pexctl-aud-supply = <&vdd_1v8>; + + pci@1,0 { + nvidia,num-lanes = <4>; + status = "okay"; + }; + + pci@2,0 { + nvidia,num-lanes = <0>; + status = "disabled"; + }; + + pci@3,0 { + nvidia,num-lanes = <1>; + status = "disabled"; + }; + }; |