1 files changed, 162 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts b/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts
new file mode 100644
index 000000000..ec721d323
--- /dev/null
+++ b/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts
@@ -0,0 +1,162 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2837.dtsi"
+#include "bcm2836-rpi.dtsi"
+#include "bcm283x-rpi-lan7515.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+#include "bcm283x-rpi-wifi-bt.dtsi"
+
+/ {
+	compatible = "raspberrypi,3-model-b-plus", "brcm,bcm2837";
+	model = "Raspberry Pi 3 Model B+";
+
+	chosen {
+		/* 8250 auxiliary UART instead of pl011 */
+		stdout-path = "serial1:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0x40000000>;
+	};
+
+	leds {
+		led-act {
+			gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-pwr {
+			label = "PWR";
+			gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
+			linux,default-trigger = "default-on";
+		};
+	};
+};
+
+&bt {
+	shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
+};
+
+&firmware {
+	expgpio: gpio {
+		compatible = "raspberrypi,firmware-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "BT_ON",
+				  "WL_ON",
+				  "PWR_LED_R",
+				  "LAN_RUN",
+				  "",
+				  "CAM_GPIO0",
+				  "CAM_GPIO1",
+				  "";
+		status = "okay";
+	};
+};
+
+&gpio {
+	/*
+	 * Taken from rpi_SCH_3bplus_1p0_reduced.pdf and
+	 * the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD1",
+			  "RXD1",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "HDMI_HPD_N",
+			  "STATUS_LED_G",
+			  /* Used by BT module */
+			  "CTS0",
+			  "RTS0",
+			  "TXD0",
+			  "RXD0",
+			  /* Used by Wifi */
+			  "SD1_CLK",
+			  "SD1_CMD",
+			  "SD1_DATA0",
+			  "SD1_DATA1",
+			  "SD1_DATA2",
+			  "SD1_DATA3",
+			  "PWM0_OUT",
+			  "PWM1_OUT",
+			  "ETH_CLK",
+			  "WIFI_CLK",
+			  "SDA0",
+			  "SCL0",
+			  "SMPS_SCL",
+			  "SMPS_SDA",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
+	status = "okay";
+};
+
+/* SDHOST is used to drive the SD card */
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	status = "okay";
+	bus-width = <4>;
+};
+
+/* uart0 communicates with the BT module */
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>;
+};
+
+/* uart1 is mapped to the pin header */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_gpio14>;
+	status = "okay";
+};
+
+&wifi_pwrseq {
+	reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+};