diff options
Diffstat (limited to 'arch/arm/boot/dts/intel-ixp42x-linksys-nslu2.dts')
| -rw-r--r-- | arch/arm/boot/dts/intel-ixp42x-linksys-nslu2.dts | 162 |
1 files changed, 162 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/intel-ixp42x-linksys-nslu2.dts b/arch/arm/boot/dts/intel-ixp42x-linksys-nslu2.dts new file mode 100644 index 000000000..0edc5928e --- /dev/null +++ b/arch/arm/boot/dts/intel-ixp42x-linksys-nslu2.dts @@ -0,0 +1,162 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for Linksys NSLU2 + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Linksys NSLU2 (Network Storage Link for USB 2.0 Disk Drives)"; + compatible = "linksys,nslu2", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + /* 32 MB SDRAM */ + device_type = "memory"; + reg = <0x00000000 0x2000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8 root=/dev/mtdblock2 rw rootfstype=squashfs,jffs2 rootwait"; + stdout-path = "uart0:115200n8"; + }; + + aliases { + serial0 = &uart0; + }; + + leds { + compatible = "gpio-leds"; + led-status { + label = "nslu2:red:status"; + gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>; + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + led-ready { + label = "nslu2:green:ready"; + gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + led-disk-1 { + label = "nslu2:green:disk-1"; + gpios = <&gpio0 3 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + led-disk-2 { + label = "nslu2:green:disk-2"; + gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + + button-power { + wakeup-source; + linux,code = <KEY_POWER>; + label = "power"; + gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>; + }; + button-reset { + wakeup-source; + linux,code = <KEY_ESC>; + label = "reset"; + gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; + }; + }; + + i2c { + compatible = "i2c-gpio"; + sda-gpios = <&gpio0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + #address-cells = <1>; + #size-cells = <0>; + + rtc@6f { + compatible = "xicor,x1205"; + reg = <0x6f>; + }; + }; + + gpio-poweroff { + compatible = "gpio-poweroff"; + gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>; + timeout-ms = <5000>; + }; + + gpio-beeper { + compatible = "gpio-beeper"; + gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>; + }; + + soc { + bus@c4000000 { + /* The first 16MB region at CS0 on the expansion bus */ + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* + * 8 MB of Flash in 0x20000 byte blocks + * mapped in at CS0. + */ + reg = <0 0x00000000 0x800000>; + + partitions { + compatible = "redboot-fis"; + /* Eraseblock at 0x7e0000 */ + fis-index-block = <0x3f>; + }; + }; + }; + + pci@c0000000 { + status = "ok"; + + /* + * Taken from NSLU2 PCI boardfile, INT A, B, C swizzled D constant + * We have slots (IDSEL) 1, 2 and 3. + */ + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + /* IDSEL 1 */ + <0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */ + <0x0800 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 10 */ + <0x0800 0 0 3 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 9 */ + <0x0800 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */ + /* IDSEL 2 */ + <0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */ + <0x1000 0 0 2 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */ + <0x1000 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 11 */ + <0x1000 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 2 is irq 8 */ + /* IDSEL 3 */ + <0x1800 0 0 1 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 9 */ + <0x1800 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 11 */ + <0x1800 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 10 */ + <0x1800 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 3 is irq 8 */ + }; + + ethernet@c8009000 { + status = "ok"; + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 20>; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + }; + }; + }; +}; |