diff options
Diffstat (limited to 'arch/arm/boot/dts/stm32mp151a-prtt1l.dtsi')
| -rw-r--r-- | arch/arm/boot/dts/stm32mp151a-prtt1l.dtsi | 233 |
1 files changed, 233 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/stm32mp151a-prtt1l.dtsi b/arch/arm/boot/dts/stm32mp151a-prtt1l.dtsi new file mode 100644 index 000000000..dd23de851 --- /dev/null +++ b/arch/arm/boot/dts/stm32mp151a-prtt1l.dtsi @@ -0,0 +1,233 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * Copyright (C) Protonic Holland + * Author: David Jander <david@protonic.nl> + */ +/dts-v1/; + +#include "stm32mp151.dtsi" +#include "stm32mp15-pinctrl.dtsi" +#include "stm32mp15xxad-pinctrl.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> + +/ { + aliases { + ethernet0 = ðernet0; + mdio-gpio0 = &mdio0; + serial0 = &uart4; + }; + + led-controller-0 { + compatible = "gpio-leds"; + + led-0 { + color = <LED_COLOR_ID_RED>; + function = LED_FUNCTION_INDICATOR; + gpios = <&gpioa 13 GPIO_ACTIVE_LOW>; + }; + + led-1 { + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_INDICATOR; + gpios = <&gpioa 14 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + }; + }; + + + /* DP83TD510E PHYs have max MDC rate of 1.75MHz. Since we can't reduce + * stmmac MDC clock without reducing system bus rate, we need to use + * gpio based MDIO bus. + */ + mdio0: mdio { + compatible = "virtual,mdio-gpio"; + #address-cells = <1>; + #size-cells = <0>; + gpios = <&gpioc 1 GPIO_ACTIVE_HIGH + &gpioa 2 GPIO_ACTIVE_HIGH>; + }; + + reg_3v3: regulator-3v3 { + compatible = "regulator-fixed"; + regulator-name = "3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; + +&dts { + status = "okay"; +}; + +ðernet0 { + pinctrl-0 = <ðernet0_rmii_pins_a>; + pinctrl-1 = <ðernet0_rmii_sleep_pins_a>; + pinctrl-names = "default", "sleep"; + phy-mode = "rmii"; + status = "okay"; +}; + +ðernet0_rmii_pins_a { + pins1 { + pinmux = <STM32_PINMUX('B', 12, AF11)>, /* ETH1_RMII_TXD0 */ + <STM32_PINMUX('B', 13, AF11)>, /* ETH1_RMII_TXD1 */ + <STM32_PINMUX('B', 11, AF11)>; /* ETH1_RMII_TX_EN */ + }; + pins2 { + pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH1_RMII_RXD0 */ + <STM32_PINMUX('C', 5, AF11)>, /* ETH1_RMII_RXD1 */ + <STM32_PINMUX('A', 1, AF11)>, /* ETH1_RMII_REF_CLK input */ + <STM32_PINMUX('A', 7, AF11)>; /* ETH1_RMII_CRS_DV */ + }; +}; + +ðernet0_rmii_sleep_pins_a { + pins1 { + pinmux = <STM32_PINMUX('B', 12, ANALOG)>, /* ETH1_RMII_TXD0 */ + <STM32_PINMUX('B', 13, ANALOG)>, /* ETH1_RMII_TXD1 */ + <STM32_PINMUX('B', 11, ANALOG)>, /* ETH1_RMII_TX_EN */ + <STM32_PINMUX('C', 4, ANALOG)>, /* ETH1_RMII_RXD0 */ + <STM32_PINMUX('C', 5, ANALOG)>, /* ETH1_RMII_RXD1 */ + <STM32_PINMUX('A', 1, ANALOG)>, /* ETH1_RMII_REF_CLK */ + <STM32_PINMUX('A', 7, ANALOG)>; /* ETH1_RMII_CRS_DV */ + }; +}; + +&iwdg2 { + status = "okay"; +}; + +&qspi { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&qspi_clk_pins_a + &qspi_bk1_pins_a + &qspi_cs1_pins_a>; + pinctrl-1 = <&qspi_clk_sleep_pins_a + &qspi_bk1_sleep_pins_a + &qspi_cs1_sleep_pins_a>; + reg = <0x58003000 0x1000>, <0x70000000 0x4000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + flash@0 { + compatible = "spi-nand"; + reg = <0>; + spi-rx-bus-width = <4>; + spi-max-frequency = <104000000>; + #address-cells = <1>; + #size-cells = <1>; + }; +}; + +&qspi_bk1_pins_a { + pins1 { + bias-pull-up; + drive-push-pull; + slew-rate = <1>; + }; +}; + +&rng1 { + status = "okay"; +}; + +&sdmmc1 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc1_b4_pins_a>; + pinctrl-1 = <&sdmmc1_b4_od_pins_a>; + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; + broken-cd; + st,neg-edge; + bus-width = <4>; + vmmc-supply = <®_3v3>; + vqmmc-supply = <®_3v3>; + status = "okay"; +}; + +&sdmmc1_b4_od_pins_a { + pins1 { + bias-pull-up; + }; + pins2 { + bias-pull-up; + }; +}; + +&sdmmc1_b4_pins_a { + pins1 { + bias-pull-up; + }; + pins2 { + bias-pull-up; + }; +}; + +&uart4 { + pinctrl-names = "default", "sleep", "idle"; + pinctrl-0 = <&uart4_pins_a>; + pinctrl-1 = <&uart4_sleep_pins_a>; + pinctrl-2 = <&uart4_idle_pins_a>; + /delete-property/dmas; + /delete-property/dma-names; + status = "okay"; +}; + +&uart4_idle_pins_a { + pins1 { + pinmux = <STM32_PINMUX('B', 9, ANALOG)>; /* UART4_TX */ + }; + pins2 { + pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */ + bias-pull-up; + }; +}; + +&uart4_pins_a { + pins1 { + pinmux = <STM32_PINMUX('B', 9, AF8)>; /* UART4_TX */ + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins2 { + pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */ + bias-pull-up; + }; +}; + +&uart4_sleep_pins_a { + pins { + pinmux = <STM32_PINMUX('B', 9, ANALOG)>, /* UART4_TX */ + <STM32_PINMUX('B', 2, ANALOG)>; /* UART4_RX */ + }; +}; + +&usbh_ehci { + phys = <&usbphyc_port0>; + phy-names = "usb"; + status = "okay"; +}; + +&usbotg_hs { + dr_mode = "host"; + pinctrl-0 = <&usbotg_hs_pins_a>; + pinctrl-names = "default"; + phys = <&usbphyc_port1 0>; + phy-names = "usb2-phy"; + status = "okay"; +}; + +&usbphyc { + status = "okay"; +}; + +&usbphyc_port0 { + phy-supply = <®_3v3>; +}; + +&usbphyc_port1 { + phy-supply = <®_3v3>; +}; |