diff options
Diffstat (limited to 'arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi')
| -rw-r--r-- | arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi | 398 |
1 files changed, 398 insertions, 0 deletions
diff --git a/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi b/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi new file mode 100644 index 000000000..7928b8197 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi @@ -0,0 +1,398 @@ +// SPDX-License-Identifier: GPL-2.0 +/* Copyright (c) 2019, Jeffrey Hugo. All rights reserved. */ + +/* + * Common include for MSM8998 clamshell devices, ie the Lenovo Miix 630, + * Asus NovaGo TP370QL, and HP Envy x2. All three devices are basically the + * same, with differences in peripherals. + */ + +#include "msm8998.dtsi" +#include "pm8005.dtsi" +#include "pm8998.dtsi" + +/ { + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "vph_pwr"; + regulator-always-on; + regulator-boot-on; + }; +}; + +&blsp1_uart3 { + status = "okay"; + + bluetooth { + compatible = "qcom,wcn3990-bt"; + + vddio-supply = <&vreg_s4a_1p8>; + vddxo-supply = <&vreg_l7a_1p8>; + vddrf-supply = <&vreg_l17a_1p3>; + vddch0-supply = <&vreg_l25a_3p3>; + max-speed = <3200000>; + }; +}; + +&blsp1_uart3_on { + rx { + /delete-property/ bias-disable; + /* + * Configure a pull-up on 45 (RX). This is needed to + * avoid garbage data when the TX pin of the Bluetooth + * module is in tri-state (module powered off or not + * driving the signal yet). + */ + bias-pull-up; + }; + + cts { + /delete-property/ bias-disable; + /* + * Configure a pull-down on 47 (CTS) to match the pull + * of the Bluetooth module. + */ + bias-pull-down; + }; +}; + +/* + * The laptop FW does not appear to support the retention state as it is + * not advertised as enabled in ACPI, and enabling it in DT can cause boot + * hangs. + */ +&CPU0 { + cpu-idle-states = <&LITTLE_CPU_SLEEP_1>; +}; + +&CPU1 { + cpu-idle-states = <&LITTLE_CPU_SLEEP_1>; +}; + +&CPU2 { + cpu-idle-states = <&LITTLE_CPU_SLEEP_1>; +}; + +&CPU3 { + cpu-idle-states = <&LITTLE_CPU_SLEEP_1>; +}; + +&CPU4 { + cpu-idle-states = <&BIG_CPU_SLEEP_1>; +}; + +&CPU5 { + cpu-idle-states = <&BIG_CPU_SLEEP_1>; +}; + +&CPU6 { + cpu-idle-states = <&BIG_CPU_SLEEP_1>; +}; + +&CPU7 { + cpu-idle-states = <&BIG_CPU_SLEEP_1>; +}; + +/* + * If EFIFB is used, enabling MMCC will cause important MMSS clocks to be cleaned + * up, because as far as Linux is concerned - they are unused. Disable it by default + * on clamshell devices, as it will break them, unless either simplefb is configured to + * hold a vote for these clocks, or panels are brought up properly, using drm/msm. + */ +&mmcc { + status = "disabled"; +}; + +&mmss_smmu { + status = "disabled"; +}; + +&pcie0 { + status = "okay"; +}; + +&pcie_phy { + status = "okay"; +}; + +&pm8005_regulators { + vdd_s1-supply = <&vph_pwr>; + + pm8005_s1: s1 { /* VDD_GFX supply */ + regulator-min-microvolt = <524000>; + regulator-max-microvolt = <1100000>; + regulator-enable-ramp-delay = <500>; + + /* hack until we rig up the gpu consumer */ + regulator-always-on; + }; +}; + +&qusb2phy { + status = "okay"; + + vdd-supply = <&vreg_l1a_0p875>; + vdda-pll-supply = <&vreg_l12a_1p8>; + vdda-phy-dpdm-supply = <&vreg_l24a_3p075>; +}; + +&rpm_requests { + pm8998-regulators { + compatible = "qcom,rpm-pm8998-regulators"; + + vdd_s1-supply = <&vph_pwr>; + vdd_s2-supply = <&vph_pwr>; + vdd_s3-supply = <&vph_pwr>; + vdd_s4-supply = <&vph_pwr>; + vdd_s5-supply = <&vph_pwr>; + vdd_s6-supply = <&vph_pwr>; + vdd_s7-supply = <&vph_pwr>; + vdd_s8-supply = <&vph_pwr>; + vdd_s9-supply = <&vph_pwr>; + vdd_s10-supply = <&vph_pwr>; + vdd_s11-supply = <&vph_pwr>; + vdd_s12-supply = <&vph_pwr>; + vdd_s13-supply = <&vph_pwr>; + vdd_l1_l27-supply = <&vreg_s7a_1p025>; + vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>; + vdd_l3_l11-supply = <&vreg_s7a_1p025>; + vdd_l4_l5-supply = <&vreg_s7a_1p025>; + vdd_l6-supply = <&vreg_s5a_2p04>; + vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>; + vdd_l9-supply = <&vph_pwr>; + vdd_l10_l23_l25-supply = <&vph_pwr>; + vdd_l13_l19_l21-supply = <&vph_pwr>; + vdd_l16_l28-supply = <&vph_pwr>; + vdd_l18_l22-supply = <&vph_pwr>; + vdd_l20_l24-supply = <&vph_pwr>; + vdd_l26-supply = <&vreg_s3a_1p35>; + vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>; + + vreg_s3a_1p35: s3 { + regulator-min-microvolt = <1352000>; + regulator-max-microvolt = <1352000>; + }; + + vreg_s4a_1p8: s4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-allow-set-load; + }; + + vreg_s5a_2p04: s5 { + regulator-min-microvolt = <1904000>; + regulator-max-microvolt = <2040000>; + }; + + vreg_s7a_1p025: s7 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1028000>; + }; + + vreg_l1a_0p875: l1 { + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-allow-set-load; + }; + + vreg_l2a_1p2: l2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-allow-set-load; + }; + + vreg_l3a_1p0: l3 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + vreg_l5a_0p8: l5 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + }; + + vreg_l6a_1p8: l6 { + regulator-min-microvolt = <1808000>; + regulator-max-microvolt = <1808000>; + }; + + vreg_l7a_1p8: l7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-allow-set-load; + }; + + vreg_l8a_1p2: l8 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + vreg_l9a_1p8: l9 { + regulator-min-microvolt = <1808000>; + regulator-max-microvolt = <2960000>; + }; + + vreg_l10a_1p8: l10 { + regulator-min-microvolt = <1808000>; + regulator-max-microvolt = <2960000>; + }; + + vreg_l11a_1p0: l11 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + vreg_l12a_1p8: l12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vreg_l13a_2p95: l13 { + regulator-min-microvolt = <1808000>; + regulator-max-microvolt = <2960000>; + }; + + vreg_l14a_1p88: l14 { + regulator-min-microvolt = <1880000>; + regulator-max-microvolt = <1880000>; + }; + + vreg_l15a_1p8: l15 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vreg_l16a_2p7: l16 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2704000>; + }; + + vreg_l17a_1p3: l17 { + regulator-min-microvolt = <1304000>; + regulator-max-microvolt = <1304000>; + regulator-allow-set-load; + }; + + vreg_l18a_2p7: l18 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2704000>; + }; + + vreg_l19a_3p0: l19 { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3008000>; + }; + + vreg_l20a_2p95: l20 { + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-allow-set-load; + }; + + vreg_l21a_2p95: l21 { + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-allow-set-load; + regulator-system-load = <800000>; + }; + + vreg_l22a_2p85: l22 { + regulator-min-microvolt = <2864000>; + regulator-max-microvolt = <2864000>; + }; + + vreg_l23a_3p3: l23 { + regulator-min-microvolt = <3312000>; + regulator-max-microvolt = <3312000>; + }; + + vreg_l24a_3p075: l24 { + regulator-min-microvolt = <3088000>; + regulator-max-microvolt = <3088000>; + }; + + vreg_l25a_3p3: l25 { + regulator-min-microvolt = <3104000>; + regulator-max-microvolt = <3312000>; + regulator-allow-set-load; + }; + + vreg_l26a_1p2: l26 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + vreg_l28_3p0: l28 { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3008000>; + }; + + vreg_lvs1a_1p8: lvs1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vreg_lvs2a_1p8: lvs2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + }; +}; + +&remoteproc_mss { + status = "okay"; +}; + +&sdhc2 { + status = "okay"; + + vmmc-supply = <&vreg_l21a_2p95>; + vqmmc-supply = <&vreg_l13a_2p95>; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc2_on &sdc2_cd>; + pinctrl-1 = <&sdc2_off &sdc2_cd>; +}; + +&tlmm { + gpio-reserved-ranges = <0 4>, <81 4>; + + touchpad: touchpad-pin { + pins = "gpio123"; + bias-pull-up; + }; +}; + +&ufshc { + status = "okay"; +}; + +&ufsphy { + status = "okay"; + vdda-phy-supply = <&vreg_l1a_0p875>; + vdda-pll-supply = <&vreg_l2a_1p2>; +}; + +&usb3 { + status = "okay"; +}; + +&usb3_dwc3 { + dr_mode = "host"; /* Force to host until we have Type-C hooked up */ +}; + +&usb3phy { + status = "okay"; + + vdda-phy-supply = <&vreg_l1a_0p875>; + vdda-pll-supply = <&vreg_l2a_1p2>; +}; + +&wifi { + status = "okay"; + + vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>; + vdd-1.8-xo-supply = <&vreg_l7a_1p8>; + vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; + vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; +}; |