1645 files changed, 337706 insertions, 0 deletions

diff --git a/arch/mips/Kbuild b/arch/mips/Kbuild
new file mode 100644
index 000000000..9e8071f0e
--- /dev/null
+++ b/arch/mips/Kbuild
@@ -0,0 +1,30 @@
+# SPDX-License-Identifier: GPL-2.0
+# Fail on warnings - also for files referenced in subdirs
+# -Werror can be disabled for specific files using:
+# CFLAGS_<file.o> := -Wno-error
+ifeq ($(W),)
+subdir-ccflags-y := -Werror
+endif
+
+# platform specific definitions
+include arch/mips/Kbuild.platforms
+obj-y := $(platform-y)
+
+# make clean traverses $(obj-) without having included .config, so
+# everything ends up here
+obj- := $(platform-y)
+
+# mips object files
+# The object files are linked as core-y files would be linked
+
+obj-y += kernel/
+obj-y += mm/
+obj-y += net/
+obj-y += vdso/
+
+ifdef CONFIG_KVM
+obj-y += kvm/
+endif
+
+# for cleaning
+subdir- += boot
diff --git a/arch/mips/Kbuild.platforms b/arch/mips/Kbuild.platforms
new file mode 100644
index 000000000..5d04438ee
--- /dev/null
+++ b/arch/mips/Kbuild.platforms
@@ -0,0 +1,38 @@
+# SPDX-License-Identifier: GPL-2.0
+# All platforms listed in alphabetic order
+
+platform-$(CONFIG_MIPS_ALCHEMY)		+= alchemy/
+platform-$(CONFIG_AR7)			+= ar7/
+platform-$(CONFIG_ATH25)		+= ath25/
+platform-$(CONFIG_ATH79)		+= ath79/
+platform-$(CONFIG_BCM47XX)		+= bcm47xx/
+platform-$(CONFIG_BCM63XX)		+= bcm63xx/
+platform-$(CONFIG_BMIPS_GENERIC)	+= bmips/
+platform-$(CONFIG_CAVIUM_OCTEON_SOC)	+= cavium-octeon/
+platform-$(CONFIG_MIPS_COBALT)		+= cobalt/
+platform-$(CONFIG_MACH_DECSTATION)	+= dec/
+platform-$(CONFIG_MIPS_GENERIC)		+= generic/
+platform-$(CONFIG_MACH_JAZZ)		+= jazz/
+platform-$(CONFIG_LANTIQ)		+= lantiq/
+platform-$(CONFIG_MACH_LOONGSON2EF)	+= loongson2ef/
+platform-$(CONFIG_MACH_LOONGSON32)	+= loongson32/
+platform-$(CONFIG_MACH_LOONGSON64)	+= loongson64/
+platform-$(CONFIG_MIPS_MALTA)		+= mti-malta/
+platform-$(CONFIG_MACH_NINTENDO64)	+= n64/
+platform-$(CONFIG_PIC32MZDA)		+= pic32/
+platform-$(CONFIG_RALINK)		+= ralink/
+platform-$(CONFIG_MIKROTIK_RB532)	+= rb532/
+platform-$(CONFIG_SGI_IP22)		+= sgi-ip22/
+platform-$(CONFIG_SGI_IP27)		+= sgi-ip27/
+platform-$(CONFIG_SGI_IP28)		+= sgi-ip22/
+platform-$(CONFIG_SGI_IP30)		+= sgi-ip30/
+platform-$(CONFIG_SGI_IP32)		+= sgi-ip32/
+platform-$(CONFIG_SIBYTE_BCM112X)	+= sibyte/
+platform-$(CONFIG_SIBYTE_SB1250)	+= sibyte/
+platform-$(CONFIG_SIBYTE_BCM1x55)	+= sibyte/
+platform-$(CONFIG_SIBYTE_BCM1x80)	+= sibyte/
+platform-$(CONFIG_SNI_RM)		+= sni/
+platform-$(CONFIG_MACH_TX49XX)		+= txx9/
+
+# include the platform specific files
+include $(patsubst %/, $(srctree)/arch/mips/%/Platform, $(platform-y))
diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig
new file mode 100644
index 000000000..585783c99
--- /dev/null
+++ b/arch/mips/Kconfig
@@ -0,0 +1,3241 @@
+# SPDX-License-Identifier: GPL-2.0
+config MIPS
+	bool
+	default y
+	select ARCH_32BIT_OFF_T if !64BIT
+	select ARCH_BINFMT_ELF_STATE if MIPS_FP_SUPPORT
+	select ARCH_HAS_CPU_FINALIZE_INIT
+	select ARCH_HAS_CURRENT_STACK_POINTER if !CC_IS_CLANG || CLANG_VERSION >= 140000
+	select ARCH_HAS_DEBUG_VIRTUAL if !64BIT
+	select ARCH_HAS_FORTIFY_SOURCE
+	select ARCH_HAS_KCOV
+	select ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE if !EVA
+	select ARCH_HAS_PTE_SPECIAL if !(32BIT && CPU_HAS_RIXI)
+	select ARCH_HAS_STRNCPY_FROM_USER
+	select ARCH_HAS_STRNLEN_USER
+	select ARCH_HAS_TICK_BROADCAST if GENERIC_CLOCKEVENTS_BROADCAST
+	select ARCH_HAS_UBSAN_SANITIZE_ALL
+	select ARCH_HAS_GCOV_PROFILE_ALL
+	select ARCH_KEEP_MEMBLOCK
+	select ARCH_SUPPORTS_UPROBES
+	select ARCH_USE_BUILTIN_BSWAP
+	select ARCH_USE_CMPXCHG_LOCKREF if 64BIT
+	select ARCH_USE_MEMTEST
+	select ARCH_USE_QUEUED_RWLOCKS
+	select ARCH_USE_QUEUED_SPINLOCKS
+	select ARCH_SUPPORTS_HUGETLBFS if CPU_SUPPORTS_HUGEPAGES
+	select ARCH_WANT_DEFAULT_TOPDOWN_MMAP_LAYOUT if MMU
+	select ARCH_WANT_IPC_PARSE_VERSION
+	select ARCH_WANT_LD_ORPHAN_WARN
+	select BUILDTIME_TABLE_SORT
+	select CLONE_BACKWARDS
+	select CPU_NO_EFFICIENT_FFS if (TARGET_ISA_REV < 1)
+	select CPU_PM if CPU_IDLE
+	select GENERIC_ATOMIC64 if !64BIT
+	select GENERIC_CMOS_UPDATE
+	select GENERIC_CPU_AUTOPROBE
+	select GENERIC_GETTIMEOFDAY
+	select GENERIC_IOMAP
+	select GENERIC_IRQ_PROBE
+	select GENERIC_IRQ_SHOW
+	select GENERIC_ISA_DMA if EISA
+	select GENERIC_LIB_ASHLDI3
+	select GENERIC_LIB_ASHRDI3
+	select GENERIC_LIB_CMPDI2
+	select GENERIC_LIB_LSHRDI3
+	select GENERIC_LIB_UCMPDI2
+	select GENERIC_SCHED_CLOCK if !CAVIUM_OCTEON_SOC
+	select GENERIC_SMP_IDLE_THREAD
+	select GENERIC_TIME_VSYSCALL
+	select GUP_GET_PTE_LOW_HIGH if CPU_MIPS32 && PHYS_ADDR_T_64BIT
+	select HAVE_ARCH_COMPILER_H
+	select HAVE_ARCH_JUMP_LABEL
+	select HAVE_ARCH_KGDB if MIPS_FP_SUPPORT
+	select HAVE_ARCH_MMAP_RND_BITS if MMU
+	select HAVE_ARCH_MMAP_RND_COMPAT_BITS if MMU && COMPAT
+	select HAVE_ARCH_SECCOMP_FILTER
+	select HAVE_ARCH_TRACEHOOK
+	select HAVE_ARCH_TRANSPARENT_HUGEPAGE if CPU_SUPPORTS_HUGEPAGES
+	select HAVE_ASM_MODVERSIONS
+	select HAVE_CONTEXT_TRACKING_USER
+	select HAVE_TIF_NOHZ
+	select HAVE_C_RECORDMCOUNT
+	select HAVE_DEBUG_KMEMLEAK
+	select HAVE_DEBUG_STACKOVERFLOW
+	select HAVE_DMA_CONTIGUOUS
+	select HAVE_DYNAMIC_FTRACE
+	select HAVE_EBPF_JIT if !CPU_MICROMIPS && \
+				!CPU_DADDI_WORKAROUNDS && \
+				!CPU_R4000_WORKAROUNDS && \
+				!CPU_R4400_WORKAROUNDS
+	select HAVE_EXIT_THREAD
+	select HAVE_FAST_GUP
+	select HAVE_FTRACE_MCOUNT_RECORD
+	select HAVE_FUNCTION_GRAPH_TRACER
+	select HAVE_FUNCTION_TRACER
+	select HAVE_GCC_PLUGINS
+	select HAVE_GENERIC_VDSO
+	select HAVE_IOREMAP_PROT
+	select HAVE_IRQ_EXIT_ON_IRQ_STACK
+	select HAVE_IRQ_TIME_ACCOUNTING
+	select HAVE_KPROBES
+	select HAVE_KRETPROBES
+	select HAVE_LD_DEAD_CODE_DATA_ELIMINATION
+	select HAVE_MOD_ARCH_SPECIFIC
+	select HAVE_NMI
+	select HAVE_PERF_EVENTS
+	select HAVE_PERF_REGS
+	select HAVE_PERF_USER_STACK_DUMP
+	select HAVE_REGS_AND_STACK_ACCESS_API
+	select HAVE_RSEQ
+	select HAVE_SPARSE_SYSCALL_NR
+	select HAVE_STACKPROTECTOR
+	select HAVE_SYSCALL_TRACEPOINTS
+	select HAVE_VIRT_CPU_ACCOUNTING_GEN if 64BIT || !SMP
+	select IRQ_FORCED_THREADING
+	select ISA if EISA
+	select LOCK_MM_AND_FIND_VMA
+	select MODULES_USE_ELF_REL if MODULES
+	select MODULES_USE_ELF_RELA if MODULES && 64BIT
+	select PERF_USE_VMALLOC
+	select PCI_MSI_ARCH_FALLBACKS if PCI_MSI
+	select RTC_LIB
+	select SYSCTL_EXCEPTION_TRACE
+	select TRACE_IRQFLAGS_SUPPORT
+	select ARCH_HAS_ELFCORE_COMPAT
+	select HAVE_ARCH_KCSAN if 64BIT
+
+config MIPS_FIXUP_BIGPHYS_ADDR
+	bool
+
+config MIPS_GENERIC
+	bool
+
+config MACH_INGENIC
+	bool
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_SUPPORTS_ZBOOT
+	select DMA_NONCOHERENT
+	select ARCH_HAS_SYNC_DMA_FOR_CPU
+	select IRQ_MIPS_CPU
+	select PINCTRL
+	select GPIOLIB
+	select COMMON_CLK
+	select GENERIC_IRQ_CHIP
+	select BUILTIN_DTB if MIPS_NO_APPENDED_DTB
+	select USE_OF
+	select CPU_SUPPORTS_CPUFREQ
+	select MIPS_EXTERNAL_TIMER
+
+menu "Machine selection"
+
+choice
+	prompt "System type"
+	default MIPS_GENERIC_KERNEL
+
+config MIPS_GENERIC_KERNEL
+	bool "Generic board-agnostic MIPS kernel"
+	select ARCH_HAS_SETUP_DMA_OPS
+	select MIPS_GENERIC
+	select BOOT_RAW
+	select BUILTIN_DTB
+	select CEVT_R4K
+	select CLKSRC_MIPS_GIC
+	select COMMON_CLK
+	select CPU_MIPSR2_IRQ_EI
+	select CPU_MIPSR2_IRQ_VI
+	select CSRC_R4K
+	select DMA_NONCOHERENT
+	select HAVE_PCI
+	select IRQ_MIPS_CPU
+	select MIPS_AUTO_PFN_OFFSET
+	select MIPS_CPU_SCACHE
+	select MIPS_GIC
+	select MIPS_L1_CACHE_SHIFT_7
+	select NO_EXCEPT_FILL
+	select PCI_DRIVERS_GENERIC
+	select SMP_UP if SMP
+	select SWAP_IO_SPACE
+	select SYS_HAS_CPU_MIPS32_R1
+	select SYS_HAS_CPU_MIPS32_R2
+	select SYS_HAS_CPU_MIPS32_R6
+	select SYS_HAS_CPU_MIPS64_R1
+	select SYS_HAS_CPU_MIPS64_R2
+	select SYS_HAS_CPU_MIPS64_R6
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_64BIT_KERNEL
+	select SYS_SUPPORTS_BIG_ENDIAN
+	select SYS_SUPPORTS_HIGHMEM
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_SUPPORTS_MICROMIPS
+	select SYS_SUPPORTS_MIPS16
+	select SYS_SUPPORTS_MIPS_CPS
+	select SYS_SUPPORTS_MULTITHREADING
+	select SYS_SUPPORTS_RELOCATABLE
+	select SYS_SUPPORTS_SMARTMIPS
+	select SYS_SUPPORTS_ZBOOT
+	select UHI_BOOT
+	select USB_EHCI_BIG_ENDIAN_DESC if CPU_BIG_ENDIAN
+	select USB_EHCI_BIG_ENDIAN_MMIO if CPU_BIG_ENDIAN
+	select USB_OHCI_BIG_ENDIAN_DESC if CPU_BIG_ENDIAN
+	select USB_OHCI_BIG_ENDIAN_MMIO if CPU_BIG_ENDIAN
+	select USB_UHCI_BIG_ENDIAN_DESC if CPU_BIG_ENDIAN
+	select USB_UHCI_BIG_ENDIAN_MMIO if CPU_BIG_ENDIAN
+	select USE_OF
+	help
+	  Select this to build a kernel which aims to support multiple boards,
+	  generally using a flattened device tree passed from the bootloader
+	  using the boot protocol defined in the UHI (Unified Hosting
+	  Interface) specification.
+
+config MIPS_ALCHEMY
+	bool "Alchemy processor based machines"
+	select PHYS_ADDR_T_64BIT
+	select CEVT_R4K
+	select CSRC_R4K
+	select IRQ_MIPS_CPU
+	select DMA_NONCOHERENT		# Au1000,1500,1100 aren't, rest is
+	select MIPS_FIXUP_BIGPHYS_ADDR if PCI
+	select SYS_HAS_CPU_MIPS32_R1
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_APM_EMULATION
+	select GPIOLIB
+	select SYS_SUPPORTS_ZBOOT
+	select COMMON_CLK
+
+config AR7
+	bool "Texas Instruments AR7"
+	select BOOT_ELF32
+	select COMMON_CLK
+	select DMA_NONCOHERENT
+	select CEVT_R4K
+	select CSRC_R4K
+	select IRQ_MIPS_CPU
+	select NO_EXCEPT_FILL
+	select SWAP_IO_SPACE
+	select SYS_HAS_CPU_MIPS32_R1
+	select SYS_HAS_EARLY_PRINTK
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_SUPPORTS_MIPS16
+	select SYS_SUPPORTS_ZBOOT_UART16550
+	select GPIOLIB
+	select VLYNQ
+	help
+	  Support for the Texas Instruments AR7 System-on-a-Chip
+	  family: TNETD7100, 7200 and 7300.
+
+config ATH25
+	bool "Atheros AR231x/AR531x SoC support"
+	select CEVT_R4K
+	select CSRC_R4K
+	select DMA_NONCOHERENT
+	select IRQ_MIPS_CPU
+	select IRQ_DOMAIN
+	select SYS_HAS_CPU_MIPS32_R1
+	select SYS_SUPPORTS_BIG_ENDIAN
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_HAS_EARLY_PRINTK
+	help
+	  Support for Atheros AR231x and Atheros AR531x based boards
+
+config ATH79
+	bool "Atheros AR71XX/AR724X/AR913X based boards"
+	select ARCH_HAS_RESET_CONTROLLER
+	select BOOT_RAW
+	select CEVT_R4K
+	select CSRC_R4K
+	select DMA_NONCOHERENT
+	select GPIOLIB
+	select PINCTRL
+	select COMMON_CLK
+	select IRQ_MIPS_CPU
+	select SYS_HAS_CPU_MIPS32_R2
+	select SYS_HAS_EARLY_PRINTK
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_BIG_ENDIAN
+	select SYS_SUPPORTS_MIPS16
+	select SYS_SUPPORTS_ZBOOT_UART_PROM
+	select USE_OF
+	select USB_EHCI_ROOT_HUB_TT if USB_EHCI_HCD_PLATFORM
+	help
+	  Support for the Atheros AR71XX/AR724X/AR913X SoCs.
+
+config BMIPS_GENERIC
+	bool "Broadcom Generic BMIPS kernel"
+	select ARCH_HAS_RESET_CONTROLLER
+	select ARCH_HAS_SYNC_DMA_FOR_CPU_ALL
+	select BOOT_RAW
+	select NO_EXCEPT_FILL
+	select USE_OF
+	select CEVT_R4K
+	select CSRC_R4K
+	select SYNC_R4K
+	select COMMON_CLK
+	select BCM6345_L1_IRQ
+	select BCM7038_L1_IRQ
+	select BCM7120_L2_IRQ
+	select BRCMSTB_L2_IRQ
+	select IRQ_MIPS_CPU
+	select DMA_NONCOHERENT
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_SUPPORTS_BIG_ENDIAN
+	select SYS_SUPPORTS_HIGHMEM
+	select SYS_HAS_CPU_BMIPS32_3300
+	select SYS_HAS_CPU_BMIPS4350
+	select SYS_HAS_CPU_BMIPS4380
+	select SYS_HAS_CPU_BMIPS5000
+	select SWAP_IO_SPACE
+	select USB_EHCI_BIG_ENDIAN_DESC if CPU_BIG_ENDIAN
+	select USB_EHCI_BIG_ENDIAN_MMIO if CPU_BIG_ENDIAN
+	select USB_OHCI_BIG_ENDIAN_DESC if CPU_BIG_ENDIAN
+	select USB_OHCI_BIG_ENDIAN_MMIO if CPU_BIG_ENDIAN
+	select HARDIRQS_SW_RESEND
+	select HAVE_PCI
+	select PCI_DRIVERS_GENERIC
+	select FW_CFE
+	help
+	  Build a generic DT-based kernel image that boots on select
+	  BCM33xx cable modem chips, BCM63xx DSL chips, and BCM7xxx set-top
+	  box chips.  Note that CONFIG_CPU_BIG_ENDIAN/CONFIG_CPU_LITTLE_ENDIAN
+	  must be set appropriately for your board.
+
+config BCM47XX
+	bool "Broadcom BCM47XX based boards"
+	select BOOT_RAW
+	select CEVT_R4K
+	select CSRC_R4K
+	select DMA_NONCOHERENT
+	select HAVE_PCI
+	select IRQ_MIPS_CPU
+	select SYS_HAS_CPU_MIPS32_R1
+	select NO_EXCEPT_FILL
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_SUPPORTS_MIPS16
+	select SYS_SUPPORTS_ZBOOT
+	select SYS_HAS_EARLY_PRINTK
+	select USE_GENERIC_EARLY_PRINTK_8250
+	select GPIOLIB
+	select LEDS_GPIO_REGISTER
+	select BCM47XX_NVRAM
+	select BCM47XX_SPROM
+	select BCM47XX_SSB if !BCM47XX_BCMA
+	help
+	  Support for BCM47XX based boards
+
+config BCM63XX
+	bool "Broadcom BCM63XX based boards"
+	select BOOT_RAW
+	select CEVT_R4K
+	select CSRC_R4K
+	select SYNC_R4K
+	select DMA_NONCOHERENT
+	select IRQ_MIPS_CPU
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_BIG_ENDIAN
+	select SYS_HAS_EARLY_PRINTK
+	select SYS_HAS_CPU_BMIPS32_3300
+	select SYS_HAS_CPU_BMIPS4350
+	select SYS_HAS_CPU_BMIPS4380
+	select SWAP_IO_SPACE
+	select GPIOLIB
+	select MIPS_L1_CACHE_SHIFT_4
+	select HAVE_LEGACY_CLK
+	help
+	  Support for BCM63XX based boards
+
+config MIPS_COBALT
+	bool "Cobalt Server"
+	select CEVT_R4K
+	select CSRC_R4K
+	select CEVT_GT641XX
+	select DMA_NONCOHERENT
+	select FORCE_PCI
+	select I8253
+	select I8259
+	select IRQ_MIPS_CPU
+	select IRQ_GT641XX
+	select PCI_GT64XXX_PCI0
+	select SYS_HAS_CPU_NEVADA
+	select SYS_HAS_EARLY_PRINTK
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_64BIT_KERNEL
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select USE_GENERIC_EARLY_PRINTK_8250
+
+config MACH_DECSTATION
+	bool "DECstations"
+	select BOOT_ELF32
+	select CEVT_DS1287
+	select CEVT_R4K if CPU_R4X00
+	select CSRC_IOASIC
+	select CSRC_R4K if CPU_R4X00
+	select CPU_DADDI_WORKAROUNDS if 64BIT
+	select CPU_R4000_WORKAROUNDS if 64BIT
+	select CPU_R4400_WORKAROUNDS if 64BIT
+	select DMA_NONCOHERENT
+	select NO_IOPORT_MAP
+	select IRQ_MIPS_CPU
+	select SYS_HAS_CPU_R3000
+	select SYS_HAS_CPU_R4X00
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_64BIT_KERNEL
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_SUPPORTS_128HZ
+	select SYS_SUPPORTS_256HZ
+	select SYS_SUPPORTS_1024HZ
+	select MIPS_L1_CACHE_SHIFT_4
+	help
+	  This enables support for DEC's MIPS based workstations.  For details
+	  see the Linux/MIPS FAQ on <http://www.linux-mips.org/> and the
+	  DECstation porting pages on <http://decstation.unix-ag.org/>.
+
+	  If you have one of the following DECstation Models you definitely
+	  want to choose R4xx0 for the CPU Type:
+
+		DECstation 5000/50
+		DECstation 5000/150
+		DECstation 5000/260
+		DECsystem 5900/260
+
+	  otherwise choose R3000.
+
+config MACH_JAZZ
+	bool "Jazz family of machines"
+	select ARC_MEMORY
+	select ARC_PROMLIB
+	select ARCH_MIGHT_HAVE_PC_PARPORT
+	select ARCH_MIGHT_HAVE_PC_SERIO
+	select DMA_OPS
+	select FW_ARC
+	select FW_ARC32
+	select ARCH_MAY_HAVE_PC_FDC
+	select CEVT_R4K
+	select CSRC_R4K
+	select DEFAULT_SGI_PARTITION if CPU_BIG_ENDIAN
+	select GENERIC_ISA_DMA
+	select HAVE_PCSPKR_PLATFORM
+	select IRQ_MIPS_CPU
+	select I8253
+	select I8259
+	select ISA
+	select SYS_HAS_CPU_R4X00
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_64BIT_KERNEL
+	select SYS_SUPPORTS_100HZ
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	help
+	  This a family of machines based on the MIPS R4030 chipset which was
+	  used by several vendors to build RISC/os and Windows NT workstations.
+	  Members include the Acer PICA, MIPS Magnum 4000, MIPS Millennium and
+	  Olivetti M700-10 workstations.
+
+config MACH_INGENIC_SOC
+	bool "Ingenic SoC based machines"
+	select MIPS_GENERIC
+	select MACH_INGENIC
+	select SYS_SUPPORTS_ZBOOT_UART16550
+	select CPU_SUPPORTS_CPUFREQ
+	select MIPS_EXTERNAL_TIMER
+
+config LANTIQ
+	bool "Lantiq based platforms"
+	select DMA_NONCOHERENT
+	select IRQ_MIPS_CPU
+	select CEVT_R4K
+	select CSRC_R4K
+	select SYS_HAS_CPU_MIPS32_R1
+	select SYS_HAS_CPU_MIPS32_R2
+	select SYS_SUPPORTS_BIG_ENDIAN
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_MIPS16
+	select SYS_SUPPORTS_MULTITHREADING
+	select SYS_SUPPORTS_VPE_LOADER
+	select SYS_HAS_EARLY_PRINTK
+	select GPIOLIB
+	select SWAP_IO_SPACE
+	select BOOT_RAW
+	select HAVE_LEGACY_CLK
+	select USE_OF
+	select PINCTRL
+	select PINCTRL_LANTIQ
+	select ARCH_HAS_RESET_CONTROLLER
+	select RESET_CONTROLLER
+
+config MACH_LOONGSON32
+	bool "Loongson 32-bit family of machines"
+	select SYS_SUPPORTS_ZBOOT
+	help
+	  This enables support for the Loongson-1 family of machines.
+
+	  Loongson-1 is a family of 32-bit MIPS-compatible SoCs developed by
+	  the Institute of Computing Technology (ICT), Chinese Academy of
+	  Sciences (CAS).
+
+config MACH_LOONGSON2EF
+	bool "Loongson-2E/F family of machines"
+	select SYS_SUPPORTS_ZBOOT
+	help
+	  This enables the support of early Loongson-2E/F family of machines.
+
+config MACH_LOONGSON64
+	bool "Loongson 64-bit family of machines"
+	select ARCH_DMA_DEFAULT_COHERENT
+	select ARCH_SPARSEMEM_ENABLE
+	select ARCH_MIGHT_HAVE_PC_PARPORT
+	select ARCH_MIGHT_HAVE_PC_SERIO
+	select GENERIC_ISA_DMA_SUPPORT_BROKEN
+	select BOOT_ELF32
+	select BOARD_SCACHE
+	select CSRC_R4K
+	select CEVT_R4K
+	select CPU_HAS_WB
+	select FORCE_PCI
+	select ISA
+	select I8259
+	select IRQ_MIPS_CPU
+	select NO_EXCEPT_FILL
+	select NR_CPUS_DEFAULT_64
+	select USE_GENERIC_EARLY_PRINTK_8250
+	select PCI_DRIVERS_GENERIC
+	select SYS_HAS_CPU_LOONGSON64
+	select SYS_HAS_EARLY_PRINTK
+	select SYS_SUPPORTS_SMP
+	select SYS_SUPPORTS_HOTPLUG_CPU
+	select SYS_SUPPORTS_NUMA
+	select SYS_SUPPORTS_64BIT_KERNEL
+	select SYS_SUPPORTS_HIGHMEM
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_SUPPORTS_ZBOOT
+	select SYS_SUPPORTS_RELOCATABLE
+	select ZONE_DMA32
+	select COMMON_CLK
+	select USE_OF
+	select BUILTIN_DTB
+	select PCI_HOST_GENERIC
+	select HAVE_ARCH_NODEDATA_EXTENSION if NUMA
+	help
+	  This enables the support of Loongson-2/3 family of machines.
+
+	  Loongson-2 and Loongson-3 are 64-bit general-purpose processors with
+	  GS264/GS464/GS464E/GS464V microarchitecture (except old Loongson-2E
+	  and Loongson-2F which will be removed), developed by the Institute
+	  of Computing Technology (ICT), Chinese Academy of Sciences (CAS).
+
+config MIPS_MALTA
+	bool "MIPS Malta board"
+	select ARCH_MAY_HAVE_PC_FDC
+	select ARCH_MIGHT_HAVE_PC_PARPORT
+	select ARCH_MIGHT_HAVE_PC_SERIO
+	select BOOT_ELF32
+	select BOOT_RAW
+	select BUILTIN_DTB
+	select CEVT_R4K
+	select CLKSRC_MIPS_GIC
+	select COMMON_CLK
+	select CSRC_R4K
+	select DMA_NONCOHERENT
+	select GENERIC_ISA_DMA
+	select HAVE_PCSPKR_PLATFORM
+	select HAVE_PCI
+	select I8253
+	select I8259
+	select IRQ_MIPS_CPU
+	select MIPS_BONITO64
+	select MIPS_CPU_SCACHE
+	select MIPS_GIC
+	select MIPS_L1_CACHE_SHIFT_6
+	select MIPS_MSC
+	select PCI_GT64XXX_PCI0
+	select SMP_UP if SMP
+	select SWAP_IO_SPACE
+	select SYS_HAS_CPU_MIPS32_R1
+	select SYS_HAS_CPU_MIPS32_R2
+	select SYS_HAS_CPU_MIPS32_R3_5
+	select SYS_HAS_CPU_MIPS32_R5
+	select SYS_HAS_CPU_MIPS32_R6
+	select SYS_HAS_CPU_MIPS64_R1
+	select SYS_HAS_CPU_MIPS64_R2
+	select SYS_HAS_CPU_MIPS64_R6
+	select SYS_HAS_CPU_NEVADA
+	select SYS_HAS_CPU_RM7000
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_64BIT_KERNEL
+	select SYS_SUPPORTS_BIG_ENDIAN
+	select SYS_SUPPORTS_HIGHMEM
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_SUPPORTS_MICROMIPS
+	select SYS_SUPPORTS_MIPS16
+	select SYS_SUPPORTS_MIPS_CMP
+	select SYS_SUPPORTS_MIPS_CPS
+	select SYS_SUPPORTS_MULTITHREADING
+	select SYS_SUPPORTS_RELOCATABLE
+	select SYS_SUPPORTS_SMARTMIPS
+	select SYS_SUPPORTS_VPE_LOADER
+	select SYS_SUPPORTS_ZBOOT
+	select USE_OF
+	select WAR_ICACHE_REFILLS
+	select ZONE_DMA32 if 64BIT
+	help
+	  This enables support for the MIPS Technologies Malta evaluation
+	  board.
+
+config MACH_PIC32
+	bool "Microchip PIC32 Family"
+	help
+	  This enables support for the Microchip PIC32 family of platforms.
+
+	  Microchip PIC32 is a family of general-purpose 32 bit MIPS core
+	  microcontrollers.
+
+config MACH_NINTENDO64
+	bool "Nintendo 64 console"
+	select CEVT_R4K
+	select CSRC_R4K
+	select SYS_HAS_CPU_R4300
+	select SYS_SUPPORTS_BIG_ENDIAN
+	select SYS_SUPPORTS_ZBOOT
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_64BIT_KERNEL
+	select DMA_NONCOHERENT
+	select IRQ_MIPS_CPU
+
+config RALINK
+	bool "Ralink based machines"
+	select CEVT_R4K
+	select COMMON_CLK
+	select CSRC_R4K
+	select BOOT_RAW
+	select DMA_NONCOHERENT
+	select IRQ_MIPS_CPU
+	select USE_OF
+	select SYS_HAS_CPU_MIPS32_R1
+	select SYS_HAS_CPU_MIPS32_R2
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_SUPPORTS_MIPS16
+	select SYS_SUPPORTS_ZBOOT
+	select SYS_HAS_EARLY_PRINTK
+	select ARCH_HAS_RESET_CONTROLLER
+	select RESET_CONTROLLER
+
+config MACH_REALTEK_RTL
+	bool "Realtek RTL838x/RTL839x based machines"
+	select MIPS_GENERIC
+	select DMA_NONCOHERENT
+	select IRQ_MIPS_CPU
+	select CSRC_R4K
+	select CEVT_R4K
+	select SYS_HAS_CPU_MIPS32_R1
+	select SYS_HAS_CPU_MIPS32_R2
+	select SYS_SUPPORTS_BIG_ENDIAN
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_MIPS16
+	select SYS_SUPPORTS_MULTITHREADING
+	select SYS_SUPPORTS_VPE_LOADER
+	select BOOT_RAW
+	select PINCTRL
+	select USE_OF
+
+config SGI_IP22
+	bool "SGI IP22 (Indy/Indigo2)"
+	select ARC_MEMORY
+	select ARC_PROMLIB
+	select FW_ARC
+	select FW_ARC32
+	select ARCH_MIGHT_HAVE_PC_SERIO
+	select BOOT_ELF32
+	select CEVT_R4K
+	select CSRC_R4K
+	select DEFAULT_SGI_PARTITION
+	select DMA_NONCOHERENT
+	select HAVE_EISA
+	select I8253
+	select I8259
+	select IP22_CPU_SCACHE
+	select IRQ_MIPS_CPU
+	select GENERIC_ISA_DMA_SUPPORT_BROKEN
+	select SGI_HAS_I8042
+	select SGI_HAS_INDYDOG
+	select SGI_HAS_HAL2
+	select SGI_HAS_SEEQ
+	select SGI_HAS_WD93
+	select SGI_HAS_ZILOG
+	select SWAP_IO_SPACE
+	select SYS_HAS_CPU_R4X00
+	select SYS_HAS_CPU_R5000
+	select SYS_HAS_EARLY_PRINTK
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_64BIT_KERNEL
+	select SYS_SUPPORTS_BIG_ENDIAN
+	select WAR_R4600_V1_INDEX_ICACHEOP
+	select WAR_R4600_V1_HIT_CACHEOP
+	select WAR_R4600_V2_HIT_CACHEOP
+	select MIPS_L1_CACHE_SHIFT_7
+	help
+	  This are the SGI Indy, Challenge S and Indigo2, as well as certain
+	  OEM variants like the Tandem CMN B006S. To compile a Linux kernel
+	  that runs on these, say Y here.
+
+config SGI_IP27
+	bool "SGI IP27 (Origin200/2000)"
+	select ARCH_HAS_PHYS_TO_DMA
+	select ARCH_SPARSEMEM_ENABLE
+	select FW_ARC
+	select FW_ARC64
+	select ARC_CMDLINE_ONLY
+	select BOOT_ELF64
+	select DEFAULT_SGI_PARTITION
+	select FORCE_PCI
+	select SYS_HAS_EARLY_PRINTK
+	select HAVE_PCI
+	select IRQ_MIPS_CPU
+	select IRQ_DOMAIN_HIERARCHY
+	select NR_CPUS_DEFAULT_64
+	select PCI_DRIVERS_GENERIC
+	select PCI_XTALK_BRIDGE
+	select SYS_HAS_CPU_R10000
+	select SYS_SUPPORTS_64BIT_KERNEL
+	select SYS_SUPPORTS_BIG_ENDIAN
+	select SYS_SUPPORTS_NUMA
+	select SYS_SUPPORTS_SMP
+	select WAR_R10000_LLSC
+	select MIPS_L1_CACHE_SHIFT_7
+	select NUMA
+	select HAVE_ARCH_NODEDATA_EXTENSION
+	help
+	  This are the SGI Origin 200, Origin 2000 and Onyx 2 Graphics
+	  workstations.  To compile a Linux kernel that runs on these, say Y
+	  here.
+
+config SGI_IP28
+	bool "SGI IP28 (Indigo2 R10k)"
+	select ARC_MEMORY
+	select ARC_PROMLIB
+	select FW_ARC
+	select FW_ARC64
+	select ARCH_MIGHT_HAVE_PC_SERIO
+	select BOOT_ELF64
+	select CEVT_R4K
+	select CSRC_R4K
+	select DEFAULT_SGI_PARTITION
+	select DMA_NONCOHERENT
+	select GENERIC_ISA_DMA_SUPPORT_BROKEN
+	select IRQ_MIPS_CPU
+	select HAVE_EISA
+	select I8253
+	select I8259
+	select SGI_HAS_I8042
+	select SGI_HAS_INDYDOG
+	select SGI_HAS_HAL2
+	select SGI_HAS_SEEQ
+	select SGI_HAS_WD93
+	select SGI_HAS_ZILOG
+	select SWAP_IO_SPACE
+	select SYS_HAS_CPU_R10000
+	select SYS_HAS_EARLY_PRINTK
+	select SYS_SUPPORTS_64BIT_KERNEL
+	select SYS_SUPPORTS_BIG_ENDIAN
+	select WAR_R10000_LLSC
+	select MIPS_L1_CACHE_SHIFT_7
+	help
+	  This is the SGI Indigo2 with R10000 processor.  To compile a Linux
+	  kernel that runs on these, say Y here.
+
+config SGI_IP30
+	bool "SGI IP30 (Octane/Octane2)"
+	select ARCH_HAS_PHYS_TO_DMA
+	select FW_ARC
+	select FW_ARC64
+	select BOOT_ELF64
+	select CEVT_R4K
+	select CSRC_R4K
+	select FORCE_PCI
+	select SYNC_R4K if SMP
+	select ZONE_DMA32
+	select HAVE_PCI
+	select IRQ_MIPS_CPU
+	select IRQ_DOMAIN_HIERARCHY
+	select PCI_DRIVERS_GENERIC
+	select PCI_XTALK_BRIDGE
+	select SYS_HAS_EARLY_PRINTK
+	select SYS_HAS_CPU_R10000
+	select SYS_SUPPORTS_64BIT_KERNEL
+	select SYS_SUPPORTS_BIG_ENDIAN
+	select SYS_SUPPORTS_SMP
+	select WAR_R10000_LLSC
+	select MIPS_L1_CACHE_SHIFT_7
+	select ARC_MEMORY
+	help
+	  These are the SGI Octane and Octane2 graphics workstations.  To
+	  compile a Linux kernel that runs on these, say Y here.
+
+config SGI_IP32
+	bool "SGI IP32 (O2)"
+	select ARC_MEMORY
+	select ARC_PROMLIB
+	select ARCH_HAS_PHYS_TO_DMA
+	select FW_ARC
+	select FW_ARC32
+	select BOOT_ELF32
+	select CEVT_R4K
+	select CSRC_R4K
+	select DMA_NONCOHERENT
+	select HAVE_PCI
+	select IRQ_MIPS_CPU
+	select R5000_CPU_SCACHE
+	select RM7000_CPU_SCACHE
+	select SYS_HAS_CPU_R5000
+	select SYS_HAS_CPU_R10000 if BROKEN
+	select SYS_HAS_CPU_RM7000
+	select SYS_HAS_CPU_NEVADA
+	select SYS_SUPPORTS_64BIT_KERNEL
+	select SYS_SUPPORTS_BIG_ENDIAN
+	select WAR_ICACHE_REFILLS
+	help
+	  If you want this kernel to run on SGI O2 workstation, say Y here.
+
+config SIBYTE_CRHINE
+	bool "Sibyte BCM91120C-CRhine"
+	select BOOT_ELF32
+	select SIBYTE_BCM1120
+	select SWAP_IO_SPACE
+	select SYS_HAS_CPU_SB1
+	select SYS_SUPPORTS_BIG_ENDIAN
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+
+config SIBYTE_CARMEL
+	bool "Sibyte BCM91120x-Carmel"
+	select BOOT_ELF32
+	select SIBYTE_BCM1120
+	select SWAP_IO_SPACE
+	select SYS_HAS_CPU_SB1
+	select SYS_SUPPORTS_BIG_ENDIAN
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+
+config SIBYTE_CRHONE
+	bool "Sibyte BCM91125C-CRhone"
+	select BOOT_ELF32
+	select SIBYTE_BCM1125
+	select SWAP_IO_SPACE
+	select SYS_HAS_CPU_SB1
+	select SYS_SUPPORTS_BIG_ENDIAN
+	select SYS_SUPPORTS_HIGHMEM
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+
+config SIBYTE_RHONE
+	bool "Sibyte BCM91125E-Rhone"
+	select BOOT_ELF32
+	select SIBYTE_BCM1125H
+	select SWAP_IO_SPACE
+	select SYS_HAS_CPU_SB1
+	select SYS_SUPPORTS_BIG_ENDIAN
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+
+config SIBYTE_SWARM
+	bool "Sibyte BCM91250A-SWARM"
+	select BOOT_ELF32
+	select HAVE_PATA_PLATFORM
+	select SIBYTE_SB1250
+	select SWAP_IO_SPACE
+	select SYS_HAS_CPU_SB1
+	select SYS_SUPPORTS_BIG_ENDIAN
+	select SYS_SUPPORTS_HIGHMEM
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select ZONE_DMA32 if 64BIT
+	select SWIOTLB if ARCH_DMA_ADDR_T_64BIT && PCI
+
+config SIBYTE_LITTLESUR
+	bool "Sibyte BCM91250C2-LittleSur"
+	select BOOT_ELF32
+	select HAVE_PATA_PLATFORM
+	select SIBYTE_SB1250
+	select SWAP_IO_SPACE
+	select SYS_HAS_CPU_SB1
+	select SYS_SUPPORTS_BIG_ENDIAN
+	select SYS_SUPPORTS_HIGHMEM
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select ZONE_DMA32 if 64BIT
+
+config SIBYTE_SENTOSA
+	bool "Sibyte BCM91250E-Sentosa"
+	select BOOT_ELF32
+	select SIBYTE_SB1250
+	select SWAP_IO_SPACE
+	select SYS_HAS_CPU_SB1
+	select SYS_SUPPORTS_BIG_ENDIAN
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SWIOTLB if ARCH_DMA_ADDR_T_64BIT && PCI
+
+config SIBYTE_BIGSUR
+	bool "Sibyte BCM91480B-BigSur"
+	select BOOT_ELF32
+	select NR_CPUS_DEFAULT_4
+	select SIBYTE_BCM1x80
+	select SWAP_IO_SPACE
+	select SYS_HAS_CPU_SB1
+	select SYS_SUPPORTS_BIG_ENDIAN
+	select SYS_SUPPORTS_HIGHMEM
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select ZONE_DMA32 if 64BIT
+	select SWIOTLB if ARCH_DMA_ADDR_T_64BIT && PCI
+
+config SNI_RM
+	bool "SNI RM200/300/400"
+	select ARC_MEMORY
+	select ARC_PROMLIB
+	select FW_ARC if CPU_LITTLE_ENDIAN
+	select FW_ARC32 if CPU_LITTLE_ENDIAN
+	select FW_SNIPROM if CPU_BIG_ENDIAN
+	select ARCH_MAY_HAVE_PC_FDC
+	select ARCH_MIGHT_HAVE_PC_PARPORT
+	select ARCH_MIGHT_HAVE_PC_SERIO
+	select BOOT_ELF32
+	select CEVT_R4K
+	select CSRC_R4K
+	select DEFAULT_SGI_PARTITION if CPU_BIG_ENDIAN
+	select DMA_NONCOHERENT
+	select GENERIC_ISA_DMA
+	select HAVE_EISA
+	select HAVE_PCSPKR_PLATFORM
+	select HAVE_PCI
+	select IRQ_MIPS_CPU
+	select I8253
+	select I8259
+	select ISA
+	select MIPS_L1_CACHE_SHIFT_6
+	select SWAP_IO_SPACE if CPU_BIG_ENDIAN
+	select SYS_HAS_CPU_R4X00
+	select SYS_HAS_CPU_R5000
+	select SYS_HAS_CPU_R10000
+	select R5000_CPU_SCACHE
+	select SYS_HAS_EARLY_PRINTK
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_64BIT_KERNEL
+	select SYS_SUPPORTS_BIG_ENDIAN
+	select SYS_SUPPORTS_HIGHMEM
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select WAR_R4600_V2_HIT_CACHEOP
+	help
+	  The SNI RM200/300/400 are MIPS-based machines manufactured by
+	  Siemens Nixdorf Informationssysteme (SNI), parent company of Pyramid
+	  Technology and now in turn merged with Fujitsu.  Say Y here to
+	  support this machine type.
+
+config MACH_TX49XX
+	bool "Toshiba TX49 series based machines"
+	select WAR_TX49XX_ICACHE_INDEX_INV
+
+config MIKROTIK_RB532
+	bool "Mikrotik RB532 boards"
+	select CEVT_R4K
+	select CSRC_R4K
+	select DMA_NONCOHERENT
+	select HAVE_PCI
+	select IRQ_MIPS_CPU
+	select SYS_HAS_CPU_MIPS32_R1
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SWAP_IO_SPACE
+	select BOOT_RAW
+	select GPIOLIB
+	select MIPS_L1_CACHE_SHIFT_4
+	help
+	  Support the Mikrotik(tm) RouterBoard 532 series,
+	  based on the IDT RC32434 SoC.
+
+config CAVIUM_OCTEON_SOC
+	bool "Cavium Networks Octeon SoC based boards"
+	select CEVT_R4K
+	select ARCH_HAS_PHYS_TO_DMA
+	select HAVE_RAPIDIO
+	select PHYS_ADDR_T_64BIT
+	select SYS_SUPPORTS_64BIT_KERNEL
+	select SYS_SUPPORTS_BIG_ENDIAN
+	select EDAC_SUPPORT
+	select EDAC_ATOMIC_SCRUB
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_SUPPORTS_HOTPLUG_CPU if CPU_BIG_ENDIAN
+	select SYS_HAS_EARLY_PRINTK
+	select SYS_HAS_CPU_CAVIUM_OCTEON
+	select HAVE_PCI
+	select HAVE_PLAT_DELAY
+	select HAVE_PLAT_FW_INIT_CMDLINE
+	select HAVE_PLAT_MEMCPY
+	select ZONE_DMA32
+	select GPIOLIB
+	select USE_OF
+	select ARCH_SPARSEMEM_ENABLE
+	select SYS_SUPPORTS_SMP
+	select NR_CPUS_DEFAULT_64
+	select MIPS_NR_CPU_NR_MAP_1024
+	select BUILTIN_DTB
+	select MTD
+	select MTD_COMPLEX_MAPPINGS
+	select SWIOTLB
+	select SYS_SUPPORTS_RELOCATABLE
+	help
+	  This option supports all of the Octeon reference boards from Cavium
+	  Networks. It builds a kernel that dynamically determines the Octeon
+	  CPU type and supports all known board reference implementations.
+	  Some of the supported boards are:
+		EBT3000
+		EBH3000
+		EBH3100
+		Thunder
+		Kodama
+		Hikari
+	  Say Y here for most Octeon reference boards.
+
+endchoice
+
+source "arch/mips/alchemy/Kconfig"
+source "arch/mips/ath25/Kconfig"
+source "arch/mips/ath79/Kconfig"
+source "arch/mips/bcm47xx/Kconfig"
+source "arch/mips/bcm63xx/Kconfig"
+source "arch/mips/bmips/Kconfig"
+source "arch/mips/generic/Kconfig"
+source "arch/mips/ingenic/Kconfig"
+source "arch/mips/jazz/Kconfig"
+source "arch/mips/lantiq/Kconfig"
+source "arch/mips/pic32/Kconfig"
+source "arch/mips/ralink/Kconfig"
+source "arch/mips/sgi-ip27/Kconfig"
+source "arch/mips/sibyte/Kconfig"
+source "arch/mips/txx9/Kconfig"
+source "arch/mips/cavium-octeon/Kconfig"
+source "arch/mips/loongson2ef/Kconfig"
+source "arch/mips/loongson32/Kconfig"
+source "arch/mips/loongson64/Kconfig"
+
+endmenu
+
+config GENERIC_HWEIGHT
+	bool
+	default y
+
+config GENERIC_CALIBRATE_DELAY
+	bool
+	default y
+
+config SCHED_OMIT_FRAME_POINTER
+	bool
+	default y
+
+#
+# Select some configuration options automatically based on user selections.
+#
+config FW_ARC
+	bool
+
+config ARCH_MAY_HAVE_PC_FDC
+	bool
+
+config BOOT_RAW
+	bool
+
+config CEVT_BCM1480
+	bool
+
+config CEVT_DS1287
+	bool
+
+config CEVT_GT641XX
+	bool
+
+config CEVT_R4K
+	bool
+
+config CEVT_SB1250
+	bool
+
+config CEVT_TXX9
+	bool
+
+config CSRC_BCM1480
+	bool
+
+config CSRC_IOASIC
+	bool
+
+config CSRC_R4K
+	select CLOCKSOURCE_WATCHDOG if CPU_FREQ
+	bool
+
+config CSRC_SB1250
+	bool
+
+config MIPS_CLOCK_VSYSCALL
+	def_bool CSRC_R4K || CLKSRC_MIPS_GIC
+
+config GPIO_TXX9
+	select GPIOLIB
+	bool
+
+config FW_CFE
+	bool
+
+config ARCH_SUPPORTS_UPROBES
+	bool
+
+config DMA_PERDEV_COHERENT
+	bool
+	select ARCH_HAS_SETUP_DMA_OPS
+	select DMA_NONCOHERENT
+
+config DMA_NONCOHERENT
+	bool
+	#
+	# MIPS allows mixing "slightly different" Cacheability and Coherency
+	# Attribute bits.  It is believed that the uncached access through
+	# KSEG1 and the implementation specific "uncached accelerated" used
+	# by pgprot_writcombine can be mixed, and the latter sometimes provides
+	# significant advantages.
+	#
+	select ARCH_HAS_DMA_WRITE_COMBINE
+	select ARCH_HAS_DMA_PREP_COHERENT
+	select ARCH_HAS_SYNC_DMA_FOR_DEVICE
+	select ARCH_HAS_DMA_SET_UNCACHED
+	select DMA_NONCOHERENT_MMAP
+	select NEED_DMA_MAP_STATE
+
+config SYS_HAS_EARLY_PRINTK
+	bool
+
+config SYS_SUPPORTS_HOTPLUG_CPU
+	bool
+
+config MIPS_BONITO64
+	bool
+
+config MIPS_MSC
+	bool
+
+config SYNC_R4K
+	bool
+
+config NO_IOPORT_MAP
+	def_bool n
+
+config GENERIC_CSUM
+	def_bool CPU_NO_LOAD_STORE_LR
+
+config GENERIC_ISA_DMA
+	bool
+	select ZONE_DMA if GENERIC_ISA_DMA_SUPPORT_BROKEN=n
+	select ISA_DMA_API
+
+config GENERIC_ISA_DMA_SUPPORT_BROKEN
+	bool
+	select GENERIC_ISA_DMA
+
+config HAVE_PLAT_DELAY
+	bool
+
+config HAVE_PLAT_FW_INIT_CMDLINE
+	bool
+
+config HAVE_PLAT_MEMCPY
+	bool
+
+config ISA_DMA_API
+	bool
+
+config SYS_SUPPORTS_RELOCATABLE
+	bool
+	help
+	  Selected if the platform supports relocating the kernel.
+	  The platform must provide plat_get_fdt() if it selects CONFIG_USE_OF
+	  to allow access to command line and entropy sources.
+
+#
+# Endianness selection.  Sufficiently obscure so many users don't know what to
+# answer,so we try hard to limit the available choices.  Also the use of a
+# choice statement should be more obvious to the user.
+#
+choice
+	prompt "Endianness selection"
+	help
+	  Some MIPS machines can be configured for either little or big endian
+	  byte order. These modes require different kernels and a different
+	  Linux distribution.  In general there is one preferred byteorder for a
+	  particular system but some systems are just as commonly used in the
+	  one or the other endianness.
+
+config CPU_BIG_ENDIAN
+	bool "Big endian"
+	depends on SYS_SUPPORTS_BIG_ENDIAN
+
+config CPU_LITTLE_ENDIAN
+	bool "Little endian"
+	depends on SYS_SUPPORTS_LITTLE_ENDIAN
+
+endchoice
+
+config EXPORT_UASM
+	bool
+
+config SYS_SUPPORTS_APM_EMULATION
+	bool
+
+config SYS_SUPPORTS_BIG_ENDIAN
+	bool
+
+config SYS_SUPPORTS_LITTLE_ENDIAN
+	bool
+
+config MIPS_HUGE_TLB_SUPPORT
+	def_bool HUGETLB_PAGE || TRANSPARENT_HUGEPAGE
+
+config IRQ_MSP_SLP
+	bool
+
+config IRQ_MSP_CIC
+	bool
+
+config IRQ_TXX9
+	bool
+
+config IRQ_GT641XX
+	bool
+
+config PCI_GT64XXX_PCI0
+	bool
+
+config PCI_XTALK_BRIDGE
+	bool
+
+config NO_EXCEPT_FILL
+	bool
+
+config MIPS_SPRAM
+	bool
+
+config SWAP_IO_SPACE
+	bool
+
+config SGI_HAS_INDYDOG
+	bool
+
+config SGI_HAS_HAL2
+	bool
+
+config SGI_HAS_SEEQ
+	bool
+
+config SGI_HAS_WD93
+	bool
+
+config SGI_HAS_ZILOG
+	bool
+
+config SGI_HAS_I8042
+	bool
+
+config DEFAULT_SGI_PARTITION
+	bool
+
+config FW_ARC32
+	bool
+
+config FW_SNIPROM
+	bool
+
+config BOOT_ELF32
+	bool
+
+config MIPS_L1_CACHE_SHIFT_4
+	bool
+
+config MIPS_L1_CACHE_SHIFT_5
+	bool
+
+config MIPS_L1_CACHE_SHIFT_6
+	bool
+
+config MIPS_L1_CACHE_SHIFT_7
+	bool
+
+config MIPS_L1_CACHE_SHIFT
+	int
+	default "7" if MIPS_L1_CACHE_SHIFT_7
+	default "6" if MIPS_L1_CACHE_SHIFT_6
+	default "5" if MIPS_L1_CACHE_SHIFT_5
+	default "4" if MIPS_L1_CACHE_SHIFT_4
+	default "5"
+
+config ARC_CMDLINE_ONLY
+	bool
+
+config ARC_CONSOLE
+	bool "ARC console support"
+	depends on SGI_IP22 || SGI_IP28 || (SNI_RM && CPU_LITTLE_ENDIAN)
+
+config ARC_MEMORY
+	bool
+
+config ARC_PROMLIB
+	bool
+
+config FW_ARC64
+	bool
+
+config BOOT_ELF64
+	bool
+
+menu "CPU selection"
+
+choice
+	prompt "CPU type"
+	default CPU_R4X00
+
+config CPU_LOONGSON64
+	bool "Loongson 64-bit CPU"
+	depends on SYS_HAS_CPU_LOONGSON64
+	select ARCH_HAS_PHYS_TO_DMA
+	select CPU_MIPSR2
+	select CPU_HAS_PREFETCH
+	select CPU_SUPPORTS_64BIT_KERNEL
+	select CPU_SUPPORTS_HIGHMEM
+	select CPU_SUPPORTS_HUGEPAGES
+	select CPU_SUPPORTS_MSA
+	select CPU_DIEI_BROKEN if !LOONGSON3_ENHANCEMENT
+	select CPU_MIPSR2_IRQ_VI
+	select DMA_NONCOHERENT
+	select WEAK_ORDERING
+	select WEAK_REORDERING_BEYOND_LLSC
+	select MIPS_ASID_BITS_VARIABLE
+	select MIPS_PGD_C0_CONTEXT
+	select MIPS_L1_CACHE_SHIFT_6
+	select MIPS_FP_SUPPORT
+	select GPIOLIB
+	select SWIOTLB
+	select HAVE_KVM
+	help
+	  The Loongson GSx64(GS264/GS464/GS464E/GS464V) series of processor
+	  cores implements the MIPS64R2 instruction set with many extensions,
+	  including most 64-bit Loongson-2 (2H, 2K) and Loongson-3 (3A1000,
+	  3B1000, 3B1500, 3A2000, 3A3000 and 3A4000) processors. However, old
+	  Loongson-2E/2F is not covered here and will be removed in future.
+
+config LOONGSON3_ENHANCEMENT
+	bool "New Loongson-3 CPU Enhancements"
+	default n
+	depends on CPU_LOONGSON64
+	help
+	  New Loongson-3 cores (since Loongson-3A R2, as opposed to Loongson-3A
+	  R1, Loongson-3B R1 and Loongson-3B R2) has many enhancements, such as
+	  FTLB, L1-VCache, EI/DI/Wait/Prefetch instruction, DSP/DSPr2 ASE, User
+	  Local register, Read-Inhibit/Execute-Inhibit, SFB (Store Fill Buffer),
+	  Fast TLB refill support, etc.
+
+	  This option enable those enhancements which are not probed at run
+	  time. If you want a generic kernel to run on all Loongson 3 machines,
+	  please say 'N' here. If you want a high-performance kernel to run on
+	  new Loongson-3 machines only, please say 'Y' here.
+
+config CPU_LOONGSON3_WORKAROUNDS
+	bool "Loongson-3 LLSC Workarounds"
+	default y if SMP
+	depends on CPU_LOONGSON64
+	help
+	  Loongson-3 processors have the llsc issues which require workarounds.
+	  Without workarounds the system may hang unexpectedly.
+
+	  Say Y, unless you know what you are doing.
+
+config CPU_LOONGSON3_CPUCFG_EMULATION
+	bool "Emulate the CPUCFG instruction on older Loongson cores"
+	default y
+	depends on CPU_LOONGSON64
+	help
+	  Loongson-3A R4 and newer have the CPUCFG instruction available for
+	  userland to query CPU capabilities, much like CPUID on x86. This
+	  option provides emulation of the instruction on older Loongson
+	  cores, back to Loongson-3A1000.
+
+	  If unsure, please say Y.
+
+config CPU_LOONGSON2E
+	bool "Loongson 2E"
+	depends on SYS_HAS_CPU_LOONGSON2E
+	select CPU_LOONGSON2EF
+	help
+	  The Loongson 2E processor implements the MIPS III instruction set
+	  with many extensions.
+
+	  It has an internal FPGA northbridge, which is compatible to
+	  bonito64.
+
+config CPU_LOONGSON2F
+	bool "Loongson 2F"
+	depends on SYS_HAS_CPU_LOONGSON2F
+	select CPU_LOONGSON2EF
+	select GPIOLIB
+	help
+	  The Loongson 2F processor implements the MIPS III instruction set
+	  with many extensions.
+
+	  Loongson2F have built-in DDR2 and PCIX controller. The PCIX controller
+	  have a similar programming interface with FPGA northbridge used in
+	  Loongson2E.
+
+config CPU_LOONGSON1B
+	bool "Loongson 1B"
+	depends on SYS_HAS_CPU_LOONGSON1B
+	select CPU_LOONGSON32
+	select LEDS_GPIO_REGISTER
+	help
+	  The Loongson 1B is a 32-bit SoC, which implements the MIPS32
+	  Release 1 instruction set and part of the MIPS32 Release 2
+	  instruction set.
+
+config CPU_LOONGSON1C
+	bool "Loongson 1C"
+	depends on SYS_HAS_CPU_LOONGSON1C
+	select CPU_LOONGSON32
+	select LEDS_GPIO_REGISTER
+	help
+	  The Loongson 1C is a 32-bit SoC, which implements the MIPS32
+	  Release 1 instruction set and part of the MIPS32 Release 2
+	  instruction set.
+
+config CPU_MIPS32_R1
+	bool "MIPS32 Release 1"
+	depends on SYS_HAS_CPU_MIPS32_R1
+	select CPU_HAS_PREFETCH
+	select CPU_SUPPORTS_32BIT_KERNEL
+	select CPU_SUPPORTS_HIGHMEM
+	help
+	  Choose this option to build a kernel for release 1 or later of the
+	  MIPS32 architecture.  Most modern embedded systems with a 32-bit
+	  MIPS processor are based on a MIPS32 processor.  If you know the
+	  specific type of processor in your system, choose those that one
+	  otherwise CPU_MIPS32_R1 is a safe bet for any MIPS32 system.
+	  Release 2 of the MIPS32 architecture is available since several
+	  years so chances are you even have a MIPS32 Release 2 processor
+	  in which case you should choose CPU_MIPS32_R2 instead for better
+	  performance.
+
+config CPU_MIPS32_R2
+	bool "MIPS32 Release 2"
+	depends on SYS_HAS_CPU_MIPS32_R2
+	select CPU_HAS_PREFETCH
+	select CPU_SUPPORTS_32BIT_KERNEL
+	select CPU_SUPPORTS_HIGHMEM
+	select CPU_SUPPORTS_MSA
+	select HAVE_KVM
+	help
+	  Choose this option to build a kernel for release 2 or later of the
+	  MIPS32 architecture.  Most modern embedded systems with a 32-bit
+	  MIPS processor are based on a MIPS32 processor.  If you know the
+	  specific type of processor in your system, choose those that one
+	  otherwise CPU_MIPS32_R1 is a safe bet for any MIPS32 system.
+
+config CPU_MIPS32_R5
+	bool "MIPS32 Release 5"
+	depends on SYS_HAS_CPU_MIPS32_R5
+	select CPU_HAS_PREFETCH
+	select CPU_SUPPORTS_32BIT_KERNEL
+	select CPU_SUPPORTS_HIGHMEM
+	select CPU_SUPPORTS_MSA
+	select HAVE_KVM
+	select MIPS_O32_FP64_SUPPORT
+	help
+	  Choose this option to build a kernel for release 5 or later of the
+	  MIPS32 architecture.  New MIPS processors, starting with the Warrior
+	  family, are based on a MIPS32r5 processor. If you own an older
+	  processor, you probably need to select MIPS32r1 or MIPS32r2 instead.
+
+config CPU_MIPS32_R6
+	bool "MIPS32 Release 6"
+	depends on SYS_HAS_CPU_MIPS32_R6
+	select CPU_HAS_PREFETCH
+	select CPU_NO_LOAD_STORE_LR
+	select CPU_SUPPORTS_32BIT_KERNEL
+	select CPU_SUPPORTS_HIGHMEM
+	select CPU_SUPPORTS_MSA
+	select HAVE_KVM
+	select MIPS_O32_FP64_SUPPORT
+	help
+	  Choose this option to build a kernel for release 6 or later of the
+	  MIPS32 architecture.  New MIPS processors, starting with the Warrior
+	  family, are based on a MIPS32r6 processor. If you own an older
+	  processor, you probably need to select MIPS32r1 or MIPS32r2 instead.
+
+config CPU_MIPS64_R1
+	bool "MIPS64 Release 1"
+	depends on SYS_HAS_CPU_MIPS64_R1
+	select CPU_HAS_PREFETCH
+	select CPU_SUPPORTS_32BIT_KERNEL
+	select CPU_SUPPORTS_64BIT_KERNEL
+	select CPU_SUPPORTS_HIGHMEM
+	select CPU_SUPPORTS_HUGEPAGES
+	help
+	  Choose this option to build a kernel for release 1 or later of the
+	  MIPS64 architecture.  Many modern embedded systems with a 64-bit
+	  MIPS processor are based on a MIPS64 processor.  If you know the
+	  specific type of processor in your system, choose those that one
+	  otherwise CPU_MIPS64_R1 is a safe bet for any MIPS64 system.
+	  Release 2 of the MIPS64 architecture is available since several
+	  years so chances are you even have a MIPS64 Release 2 processor
+	  in which case you should choose CPU_MIPS64_R2 instead for better
+	  performance.
+
+config CPU_MIPS64_R2
+	bool "MIPS64 Release 2"
+	depends on SYS_HAS_CPU_MIPS64_R2
+	select CPU_HAS_PREFETCH
+	select CPU_SUPPORTS_32BIT_KERNEL
+	select CPU_SUPPORTS_64BIT_KERNEL
+	select CPU_SUPPORTS_HIGHMEM
+	select CPU_SUPPORTS_HUGEPAGES
+	select CPU_SUPPORTS_MSA
+	select HAVE_KVM
+	help
+	  Choose this option to build a kernel for release 2 or later of the
+	  MIPS64 architecture.  Many modern embedded systems with a 64-bit
+	  MIPS processor are based on a MIPS64 processor.  If you know the
+	  specific type of processor in your system, choose those that one
+	  otherwise CPU_MIPS64_R1 is a safe bet for any MIPS64 system.
+
+config CPU_MIPS64_R5
+	bool "MIPS64 Release 5"
+	depends on SYS_HAS_CPU_MIPS64_R5
+	select CPU_HAS_PREFETCH
+	select CPU_SUPPORTS_32BIT_KERNEL
+	select CPU_SUPPORTS_64BIT_KERNEL
+	select CPU_SUPPORTS_HIGHMEM
+	select CPU_SUPPORTS_HUGEPAGES
+	select CPU_SUPPORTS_MSA
+	select MIPS_O32_FP64_SUPPORT if 32BIT || MIPS32_O32
+	select HAVE_KVM
+	help
+	  Choose this option to build a kernel for release 5 or later of the
+	  MIPS64 architecture.  This is a intermediate MIPS architecture
+	  release partly implementing release 6 features. Though there is no
+	  any hardware known to be based on this release.
+
+config CPU_MIPS64_R6
+	bool "MIPS64 Release 6"
+	depends on SYS_HAS_CPU_MIPS64_R6
+	select CPU_HAS_PREFETCH
+	select CPU_NO_LOAD_STORE_LR
+	select CPU_SUPPORTS_32BIT_KERNEL
+	select CPU_SUPPORTS_64BIT_KERNEL
+	select CPU_SUPPORTS_HIGHMEM
+	select CPU_SUPPORTS_HUGEPAGES
+	select CPU_SUPPORTS_MSA
+	select MIPS_O32_FP64_SUPPORT if 32BIT || MIPS32_O32
+	select HAVE_KVM
+	help
+	  Choose this option to build a kernel for release 6 or later of the
+	  MIPS64 architecture.  New MIPS processors, starting with the Warrior
+	  family, are based on a MIPS64r6 processor. If you own an older
+	  processor, you probably need to select MIPS64r1 or MIPS64r2 instead.
+
+config CPU_P5600
+	bool "MIPS Warrior P5600"
+	depends on SYS_HAS_CPU_P5600
+	select CPU_HAS_PREFETCH
+	select CPU_SUPPORTS_32BIT_KERNEL
+	select CPU_SUPPORTS_HIGHMEM
+	select CPU_SUPPORTS_MSA
+	select CPU_SUPPORTS_CPUFREQ
+	select CPU_MIPSR2_IRQ_VI
+	select CPU_MIPSR2_IRQ_EI
+	select HAVE_KVM
+	select MIPS_O32_FP64_SUPPORT
+	help
+	  Choose this option to build a kernel for MIPS Warrior P5600 CPU.
+	  It's based on MIPS32r5 ISA with XPA, EVA, dual/quad issue exec pipes,
+	  MMU with two-levels TLB, UCA, MSA, MDU core level features and system
+	  level features like up to six P5600 calculation cores, CM2 with L2
+	  cache, IOCU/IOMMU (though might be unused depending on the system-
+	  specific IP core configuration), GIC, CPC, virtualisation module,
+	  eJTAG and PDtrace.
+
+config CPU_R3000
+	bool "R3000"
+	depends on SYS_HAS_CPU_R3000
+	select CPU_HAS_WB
+	select CPU_R3K_TLB
+	select CPU_SUPPORTS_32BIT_KERNEL
+	select CPU_SUPPORTS_HIGHMEM
+	help
+	  Please make sure to pick the right CPU type. Linux/MIPS is not
+	  designed to be generic, i.e. Kernels compiled for R3000 CPUs will
+	  *not* work on R4000 machines and vice versa.  However, since most
+	  of the supported machines have an R4000 (or similar) CPU, R4x00
+	  might be a safe bet.  If the resulting kernel does not work,
+	  try to recompile with R3000.
+
+config CPU_R4300
+	bool "R4300"
+	depends on SYS_HAS_CPU_R4300
+	select CPU_SUPPORTS_32BIT_KERNEL
+	select CPU_SUPPORTS_64BIT_KERNEL
+	help
+	  MIPS Technologies R4300-series processors.
+
+config CPU_R4X00
+	bool "R4x00"
+	depends on SYS_HAS_CPU_R4X00
+	select CPU_SUPPORTS_32BIT_KERNEL
+	select CPU_SUPPORTS_64BIT_KERNEL
+	select CPU_SUPPORTS_HUGEPAGES
+	help
+	  MIPS Technologies R4000-series processors other than 4300, including
+	  the R4000, R4400, R4600, and 4700.
+
+config CPU_TX49XX
+	bool "R49XX"
+	depends on SYS_HAS_CPU_TX49XX
+	select CPU_HAS_PREFETCH
+	select CPU_SUPPORTS_32BIT_KERNEL
+	select CPU_SUPPORTS_64BIT_KERNEL
+	select CPU_SUPPORTS_HUGEPAGES
+
+config CPU_R5000
+	bool "R5000"
+	depends on SYS_HAS_CPU_R5000
+	select CPU_SUPPORTS_32BIT_KERNEL
+	select CPU_SUPPORTS_64BIT_KERNEL
+	select CPU_SUPPORTS_HUGEPAGES
+	help
+	  MIPS Technologies R5000-series processors other than the Nevada.
+
+config CPU_R5500
+	bool "R5500"
+	depends on SYS_HAS_CPU_R5500
+	select CPU_SUPPORTS_32BIT_KERNEL
+	select CPU_SUPPORTS_64BIT_KERNEL
+	select CPU_SUPPORTS_HUGEPAGES
+	help
+	  NEC VR5500 and VR5500A series processors implement 64-bit MIPS IV
+	  instruction set.
+
+config CPU_NEVADA
+	bool "RM52xx"
+	depends on SYS_HAS_CPU_NEVADA
+	select CPU_SUPPORTS_32BIT_KERNEL
+	select CPU_SUPPORTS_64BIT_KERNEL
+	select CPU_SUPPORTS_HUGEPAGES
+	help
+	  QED / PMC-Sierra RM52xx-series ("Nevada") processors.
+
+config CPU_R10000
+	bool "R10000"
+	depends on SYS_HAS_CPU_R10000
+	select CPU_HAS_PREFETCH
+	select CPU_SUPPORTS_32BIT_KERNEL
+	select CPU_SUPPORTS_64BIT_KERNEL
+	select CPU_SUPPORTS_HIGHMEM
+	select CPU_SUPPORTS_HUGEPAGES
+	help
+	  MIPS Technologies R10000-series processors.
+
+config CPU_RM7000
+	bool "RM7000"
+	depends on SYS_HAS_CPU_RM7000
+	select CPU_HAS_PREFETCH
+	select CPU_SUPPORTS_32BIT_KERNEL
+	select CPU_SUPPORTS_64BIT_KERNEL
+	select CPU_SUPPORTS_HIGHMEM
+	select CPU_SUPPORTS_HUGEPAGES
+
+config CPU_SB1
+	bool "SB1"
+	depends on SYS_HAS_CPU_SB1
+	select CPU_SUPPORTS_32BIT_KERNEL
+	select CPU_SUPPORTS_64BIT_KERNEL
+	select CPU_SUPPORTS_HIGHMEM
+	select CPU_SUPPORTS_HUGEPAGES
+	select WEAK_ORDERING
+
+config CPU_CAVIUM_OCTEON
+	bool "Cavium Octeon processor"
+	depends on SYS_HAS_CPU_CAVIUM_OCTEON
+	select CPU_HAS_PREFETCH
+	select CPU_SUPPORTS_64BIT_KERNEL
+	select WEAK_ORDERING
+	select CPU_SUPPORTS_HIGHMEM
+	select CPU_SUPPORTS_HUGEPAGES
+	select USB_EHCI_BIG_ENDIAN_MMIO if CPU_BIG_ENDIAN
+	select USB_OHCI_BIG_ENDIAN_MMIO if CPU_BIG_ENDIAN
+	select MIPS_L1_CACHE_SHIFT_7
+	select HAVE_KVM
+	help
+	  The Cavium Octeon processor is a highly integrated chip containing
+	  many ethernet hardware widgets for networking tasks. The processor
+	  can have up to 16 Mips64v2 cores and 8 integrated gigabit ethernets.
+	  Full details can be found at http://www.caviumnetworks.com.
+
+config CPU_BMIPS
+	bool "Broadcom BMIPS"
+	depends on SYS_HAS_CPU_BMIPS
+	select CPU_MIPS32
+	select CPU_BMIPS32_3300 if SYS_HAS_CPU_BMIPS32_3300
+	select CPU_BMIPS4350 if SYS_HAS_CPU_BMIPS4350
+	select CPU_BMIPS4380 if SYS_HAS_CPU_BMIPS4380
+	select CPU_BMIPS5000 if SYS_HAS_CPU_BMIPS5000
+	select CPU_SUPPORTS_32BIT_KERNEL
+	select DMA_NONCOHERENT
+	select IRQ_MIPS_CPU
+	select SWAP_IO_SPACE
+	select WEAK_ORDERING
+	select CPU_SUPPORTS_HIGHMEM
+	select CPU_HAS_PREFETCH
+	select CPU_SUPPORTS_CPUFREQ
+	select MIPS_EXTERNAL_TIMER
+	select GENERIC_IRQ_MIGRATION if HOTPLUG_CPU
+	help
+	  Support for BMIPS32/3300/4350/4380 and BMIPS5000 processors.
+
+endchoice
+
+config CPU_MIPS32_3_5_FEATURES
+	bool "MIPS32 Release 3.5 Features"
+	depends on SYS_HAS_CPU_MIPS32_R3_5
+	depends on CPU_MIPS32_R2 || CPU_MIPS32_R5 || CPU_MIPS32_R6 || \
+		   CPU_P5600
+	help
+	  Choose this option to build a kernel for release 2 or later of the
+	  MIPS32 architecture including features from the 3.5 release such as
+	  support for Enhanced Virtual Addressing (EVA).
+
+config CPU_MIPS32_3_5_EVA
+	bool "Enhanced Virtual Addressing (EVA)"
+	depends on CPU_MIPS32_3_5_FEATURES
+	select EVA
+	default y
+	help
+	  Choose this option if you want to enable the Enhanced Virtual
+	  Addressing (EVA) on your MIPS32 core (such as proAptiv).
+	  One of its primary benefits is an increase in the maximum size
+	  of lowmem (up to 3GB). If unsure, say 'N' here.
+
+config CPU_MIPS32_R5_FEATURES
+	bool "MIPS32 Release 5 Features"
+	depends on SYS_HAS_CPU_MIPS32_R5
+	depends on CPU_MIPS32_R2 || CPU_MIPS32_R5 || CPU_P5600
+	help
+	  Choose this option to build a kernel for release 2 or later of the
+	  MIPS32 architecture including features from release 5 such as
+	  support for Extended Physical Addressing (XPA).
+
+config CPU_MIPS32_R5_XPA
+	bool "Extended Physical Addressing (XPA)"
+	depends on CPU_MIPS32_R5_FEATURES
+	depends on !EVA
+	depends on !PAGE_SIZE_4KB
+	depends on SYS_SUPPORTS_HIGHMEM
+	select XPA
+	select HIGHMEM
+	select PHYS_ADDR_T_64BIT
+	default n
+	help
+	  Choose this option if you want to enable the Extended Physical
+	  Addressing (XPA) on your MIPS32 core (such as P5600 series). The
+	  benefit is to increase physical addressing equal to or greater
+	  than 40 bits. Note that this has the side effect of turning on
+	  64-bit addressing which in turn makes the PTEs 64-bit in size.
+	  If unsure, say 'N' here.
+
+if CPU_LOONGSON2F
+config CPU_NOP_WORKAROUNDS
+	bool
+
+config CPU_JUMP_WORKAROUNDS
+	bool
+
+config CPU_LOONGSON2F_WORKAROUNDS
+	bool "Loongson 2F Workarounds"
+	default y
+	select CPU_NOP_WORKAROUNDS
+	select CPU_JUMP_WORKAROUNDS
+	help
+	  Loongson 2F01 / 2F02 processors have the NOP & JUMP issues which
+	  require workarounds.  Without workarounds the system may hang
+	  unexpectedly.  For more information please refer to the gas
+	  -mfix-loongson2f-nop and -mfix-loongson2f-jump options.
+
+	  Loongson 2F03 and later have fixed these issues and no workarounds
+	  are needed.  The workarounds have no significant side effect on them
+	  but may decrease the performance of the system so this option should
+	  be disabled unless the kernel is intended to be run on 2F01 or 2F02
+	  systems.
+
+	  If unsure, please say Y.
+endif # CPU_LOONGSON2F
+
+config SYS_SUPPORTS_ZBOOT
+	bool
+	select HAVE_KERNEL_GZIP
+	select HAVE_KERNEL_BZIP2
+	select HAVE_KERNEL_LZ4
+	select HAVE_KERNEL_LZMA
+	select HAVE_KERNEL_LZO
+	select HAVE_KERNEL_XZ
+	select HAVE_KERNEL_ZSTD
+
+config SYS_SUPPORTS_ZBOOT_UART16550
+	bool
+	select SYS_SUPPORTS_ZBOOT
+
+config SYS_SUPPORTS_ZBOOT_UART_PROM
+	bool
+	select SYS_SUPPORTS_ZBOOT
+
+config CPU_LOONGSON2EF
+	bool
+	select CPU_SUPPORTS_32BIT_KERNEL
+	select CPU_SUPPORTS_64BIT_KERNEL
+	select CPU_SUPPORTS_HIGHMEM
+	select CPU_SUPPORTS_HUGEPAGES
+	select ARCH_HAS_PHYS_TO_DMA
+
+config CPU_LOONGSON32
+	bool
+	select CPU_MIPS32
+	select CPU_MIPSR2
+	select CPU_HAS_PREFETCH
+	select CPU_SUPPORTS_32BIT_KERNEL
+	select CPU_SUPPORTS_HIGHMEM
+	select CPU_SUPPORTS_CPUFREQ
+
+config CPU_BMIPS32_3300
+	select SMP_UP if SMP
+	bool
+
+config CPU_BMIPS4350
+	bool
+	select SYS_SUPPORTS_SMP
+	select SYS_SUPPORTS_HOTPLUG_CPU
+
+config CPU_BMIPS4380
+	bool
+	select MIPS_L1_CACHE_SHIFT_6
+	select SYS_SUPPORTS_SMP
+	select SYS_SUPPORTS_HOTPLUG_CPU
+	select CPU_HAS_RIXI
+
+config CPU_BMIPS5000
+	bool
+	select MIPS_CPU_SCACHE
+	select MIPS_L1_CACHE_SHIFT_7
+	select SYS_SUPPORTS_SMP
+	select SYS_SUPPORTS_HOTPLUG_CPU
+	select CPU_HAS_RIXI
+
+config SYS_HAS_CPU_LOONGSON64
+	bool
+	select CPU_SUPPORTS_CPUFREQ
+	select CPU_HAS_RIXI
+
+config SYS_HAS_CPU_LOONGSON2E
+	bool
+
+config SYS_HAS_CPU_LOONGSON2F
+	bool
+	select CPU_SUPPORTS_CPUFREQ
+	select CPU_SUPPORTS_ADDRWINCFG if 64BIT
+
+config SYS_HAS_CPU_LOONGSON1B
+	bool
+
+config SYS_HAS_CPU_LOONGSON1C
+	bool
+
+config SYS_HAS_CPU_MIPS32_R1
+	bool
+
+config SYS_HAS_CPU_MIPS32_R2
+	bool
+
+config SYS_HAS_CPU_MIPS32_R3_5
+	bool
+
+config SYS_HAS_CPU_MIPS32_R5
+	bool
+	select ARCH_HAS_SYNC_DMA_FOR_CPU if DMA_NONCOHERENT
+
+config SYS_HAS_CPU_MIPS32_R6
+	bool
+	select ARCH_HAS_SYNC_DMA_FOR_CPU if DMA_NONCOHERENT
+
+config SYS_HAS_CPU_MIPS64_R1
+	bool
+
+config SYS_HAS_CPU_MIPS64_R2
+	bool
+
+config SYS_HAS_CPU_MIPS64_R5
+	bool
+	select ARCH_HAS_SYNC_DMA_FOR_CPU if DMA_NONCOHERENT
+
+config SYS_HAS_CPU_MIPS64_R6
+	bool
+	select ARCH_HAS_SYNC_DMA_FOR_CPU if DMA_NONCOHERENT
+
+config SYS_HAS_CPU_P5600
+	bool
+	select ARCH_HAS_SYNC_DMA_FOR_CPU if DMA_NONCOHERENT
+
+config SYS_HAS_CPU_R3000
+	bool
+
+config SYS_HAS_CPU_R4300
+	bool
+
+config SYS_HAS_CPU_R4X00
+	bool
+
+config SYS_HAS_CPU_TX49XX
+	bool
+
+config SYS_HAS_CPU_R5000
+	bool
+
+config SYS_HAS_CPU_R5500
+	bool
+
+config SYS_HAS_CPU_NEVADA
+	bool
+
+config SYS_HAS_CPU_R10000
+	bool
+	select ARCH_HAS_SYNC_DMA_FOR_CPU if DMA_NONCOHERENT
+
+config SYS_HAS_CPU_RM7000
+	bool
+
+config SYS_HAS_CPU_SB1
+	bool
+
+config SYS_HAS_CPU_CAVIUM_OCTEON
+	bool
+
+config SYS_HAS_CPU_BMIPS
+	bool
+
+config SYS_HAS_CPU_BMIPS32_3300
+	bool
+	select SYS_HAS_CPU_BMIPS
+
+config SYS_HAS_CPU_BMIPS4350
+	bool
+	select SYS_HAS_CPU_BMIPS
+
+config SYS_HAS_CPU_BMIPS4380
+	bool
+	select SYS_HAS_CPU_BMIPS
+
+config SYS_HAS_CPU_BMIPS5000
+	bool
+	select SYS_HAS_CPU_BMIPS
+	select ARCH_HAS_SYNC_DMA_FOR_CPU
+
+#
+# CPU may reorder R->R, R->W, W->R, W->W
+# Reordering beyond LL and SC is handled in WEAK_REORDERING_BEYOND_LLSC
+#
+config WEAK_ORDERING
+	bool
+
+#
+# CPU may reorder reads and writes beyond LL/SC
+# CPU may reorder R->LL, R->LL, W->LL, W->LL, R->SC, R->SC, W->SC, W->SC
+#
+config WEAK_REORDERING_BEYOND_LLSC
+	bool
+endmenu
+
+#
+# These two indicate any level of the MIPS32 and MIPS64 architecture
+#
+config CPU_MIPS32
+	bool
+	default y if CPU_MIPS32_R1 || CPU_MIPS32_R2 || CPU_MIPS32_R5 || \
+		     CPU_MIPS32_R6 || CPU_P5600
+
+config CPU_MIPS64
+	bool
+	default y if CPU_MIPS64_R1 || CPU_MIPS64_R2 || CPU_MIPS64_R5 || \
+		     CPU_MIPS64_R6 || CPU_LOONGSON64 || CPU_CAVIUM_OCTEON
+
+#
+# These indicate the revision of the architecture
+#
+config CPU_MIPSR1
+	bool
+	default y if CPU_MIPS32_R1 || CPU_MIPS64_R1
+
+config CPU_MIPSR2
+	bool
+	default y if CPU_MIPS32_R2 || CPU_MIPS64_R2 || CPU_CAVIUM_OCTEON
+	select CPU_HAS_RIXI
+	select CPU_HAS_DIEI if !CPU_DIEI_BROKEN
+	select MIPS_SPRAM
+
+config CPU_MIPSR5
+	bool
+	default y if CPU_MIPS32_R5 || CPU_MIPS64_R5 || CPU_P5600
+	select CPU_HAS_RIXI
+	select CPU_HAS_DIEI if !CPU_DIEI_BROKEN
+	select MIPS_SPRAM
+
+config CPU_MIPSR6
+	bool
+	default y if CPU_MIPS32_R6 || CPU_MIPS64_R6
+	select CPU_HAS_RIXI
+	select CPU_HAS_DIEI if !CPU_DIEI_BROKEN
+	select HAVE_ARCH_BITREVERSE
+	select MIPS_ASID_BITS_VARIABLE
+	select MIPS_CRC_SUPPORT
+	select MIPS_SPRAM
+
+config TARGET_ISA_REV
+	int
+	default 1 if CPU_MIPSR1
+	default 2 if CPU_MIPSR2
+	default 5 if CPU_MIPSR5
+	default 6 if CPU_MIPSR6
+	default 0
+	help
+	  Reflects the ISA revision being targeted by the kernel build. This
+	  is effectively the Kconfig equivalent of MIPS_ISA_REV.
+
+config EVA
+	bool
+
+config XPA
+	bool
+
+config SYS_SUPPORTS_32BIT_KERNEL
+	bool
+config SYS_SUPPORTS_64BIT_KERNEL
+	bool
+config CPU_SUPPORTS_32BIT_KERNEL
+	bool
+config CPU_SUPPORTS_64BIT_KERNEL
+	bool
+config CPU_SUPPORTS_CPUFREQ
+	bool
+config CPU_SUPPORTS_ADDRWINCFG
+	bool
+config CPU_SUPPORTS_HUGEPAGES
+	bool
+	depends on !(32BIT && (PHYS_ADDR_T_64BIT || EVA))
+config MIPS_PGD_C0_CONTEXT
+	bool
+	depends on 64BIT
+	default y if (CPU_MIPSR2 || CPU_MIPSR6)
+
+#
+# Set to y for ptrace access to watch registers.
+#
+config HARDWARE_WATCHPOINTS
+	bool
+	default y if CPU_MIPSR1 || CPU_MIPSR2 || CPU_MIPSR6
+
+menu "Kernel type"
+
+choice
+	prompt "Kernel code model"
+	help
+	  You should only select this option if you have a workload that
+	  actually benefits from 64-bit processing or if your machine has
+	  large memory.  You will only be presented a single option in this
+	  menu if your system does not support both 32-bit and 64-bit kernels.
+
+config 32BIT
+	bool "32-bit kernel"
+	depends on CPU_SUPPORTS_32BIT_KERNEL && SYS_SUPPORTS_32BIT_KERNEL
+	select TRAD_SIGNALS
+	help
+	  Select this option if you want to build a 32-bit kernel.
+
+config 64BIT
+	bool "64-bit kernel"
+	depends on CPU_SUPPORTS_64BIT_KERNEL && SYS_SUPPORTS_64BIT_KERNEL
+	help
+	  Select this option if you want to build a 64-bit kernel.
+
+endchoice
+
+config MIPS_VA_BITS_48
+	bool "48 bits virtual memory"
+	depends on 64BIT
+	help
+	  Support a maximum at least 48 bits of application virtual
+	  memory.  Default is 40 bits or less, depending on the CPU.
+	  For page sizes 16k and above, this option results in a small
+	  memory overhead for page tables.  For 4k page size, a fourth
+	  level of page tables is added which imposes both a memory
+	  overhead as well as slower TLB fault handling.
+
+	  If unsure, say N.
+
+config ZBOOT_LOAD_ADDRESS
+	hex "Compressed kernel load address"
+	default 0xffffffff80400000 if BCM47XX
+	default 0x0
+	depends on SYS_SUPPORTS_ZBOOT
+	help
+	  The address to load compressed kernel, aka vmlinuz.
+
+	  This is only used if non-zero.
+
+choice
+	prompt "Kernel page size"
+	default PAGE_SIZE_4KB
+
+config PAGE_SIZE_4KB
+	bool "4kB"
+	depends on !CPU_LOONGSON2EF && !CPU_LOONGSON64
+	help
+	  This option select the standard 4kB Linux page size.  On some
+	  R3000-family processors this is the only available page size.  Using
+	  4kB page size will minimize memory consumption and is therefore
+	  recommended for low memory systems.
+
+config PAGE_SIZE_8KB
+	bool "8kB"
+	depends on CPU_CAVIUM_OCTEON
+	depends on !MIPS_VA_BITS_48
+	help
+	  Using 8kB page size will result in higher performance kernel at
+	  the price of higher memory consumption.  This option is available
+	  only on cnMIPS processors.  Note that you will need a suitable Linux
+	  distribution to support this.
+
+config PAGE_SIZE_16KB
+	bool "16kB"
+	depends on !CPU_R3000
+	help
+	  Using 16kB page size will result in higher performance kernel at
+	  the price of higher memory consumption.  This option is available on
+	  all non-R3000 family processors.  Note that you will need a suitable
+	  Linux distribution to support this.
+
+config PAGE_SIZE_32KB
+	bool "32kB"
+	depends on CPU_CAVIUM_OCTEON
+	depends on !MIPS_VA_BITS_48
+	help
+	  Using 32kB page size will result in higher performance kernel at
+	  the price of higher memory consumption.  This option is available
+	  only on cnMIPS cores.  Note that you will need a suitable Linux
+	  distribution to support this.
+
+config PAGE_SIZE_64KB
+	bool "64kB"
+	depends on !CPU_R3000
+	help
+	  Using 64kB page size will result in higher performance kernel at
+	  the price of higher memory consumption.  This option is available on
+	  all non-R3000 family processor.  Not that at the time of this
+	  writing this option is still high experimental.
+
+endchoice
+
+config ARCH_FORCE_MAX_ORDER
+	int "Maximum zone order"
+	range 14 64 if MIPS_HUGE_TLB_SUPPORT && PAGE_SIZE_64KB
+	default "14" if MIPS_HUGE_TLB_SUPPORT && PAGE_SIZE_64KB
+	range 13 64 if MIPS_HUGE_TLB_SUPPORT && PAGE_SIZE_32KB
+	default "13" if MIPS_HUGE_TLB_SUPPORT && PAGE_SIZE_32KB
+	range 12 64 if MIPS_HUGE_TLB_SUPPORT && PAGE_SIZE_16KB
+	default "12" if MIPS_HUGE_TLB_SUPPORT && PAGE_SIZE_16KB
+	range 0 64
+	default "11"
+	help
+	  The kernel memory allocator divides physically contiguous memory
+	  blocks into "zones", where each zone is a power of two number of
+	  pages.  This option selects the largest power of two that the kernel
+	  keeps in the memory allocator.  If you need to allocate very large
+	  blocks of physically contiguous memory, then you may need to
+	  increase this value.
+
+	  This config option is actually maximum order plus one. For example,
+	  a value of 11 means that the largest free memory block is 2^10 pages.
+
+	  The page size is not necessarily 4KB.  Keep this in mind
+	  when choosing a value for this option.
+
+config BOARD_SCACHE
+	bool
+
+config IP22_CPU_SCACHE
+	bool
+	select BOARD_SCACHE
+
+#
+# Support for a MIPS32 / MIPS64 style S-caches
+#
+config MIPS_CPU_SCACHE
+	bool
+	select BOARD_SCACHE
+
+config R5000_CPU_SCACHE
+	bool
+	select BOARD_SCACHE
+
+config RM7000_CPU_SCACHE
+	bool
+	select BOARD_SCACHE
+
+config SIBYTE_DMA_PAGEOPS
+	bool "Use DMA to clear/copy pages"
+	depends on CPU_SB1
+	help
+	  Instead of using the CPU to zero and copy pages, use a Data Mover
+	  channel.  These DMA channels are otherwise unused by the standard
+	  SiByte Linux port.  Seems to give a small performance benefit.
+
+config CPU_HAS_PREFETCH
+	bool
+
+config CPU_GENERIC_DUMP_TLB
+	bool
+	default y if !CPU_R3000
+
+config MIPS_FP_SUPPORT
+	bool "Floating Point support" if EXPERT
+	default y
+	help
+	  Select y to include support for floating point in the kernel
+	  including initialization of FPU hardware, FP context save & restore
+	  and emulation of an FPU where necessary. Without this support any
+	  userland program attempting to use floating point instructions will
+	  receive a SIGILL.
+
+	  If you know that your userland will not attempt to use floating point
+	  instructions then you can say n here to shrink the kernel a little.
+
+	  If unsure, say y.
+
+config CPU_R2300_FPU
+	bool
+	depends on MIPS_FP_SUPPORT
+	default y if CPU_R3000
+
+config CPU_R3K_TLB
+	bool
+
+config CPU_R4K_FPU
+	bool
+	depends on MIPS_FP_SUPPORT
+	default y if !CPU_R2300_FPU
+
+config CPU_R4K_CACHE_TLB
+	bool
+	default y if !(CPU_R3K_TLB || CPU_SB1 || CPU_CAVIUM_OCTEON)
+
+config MIPS_MT_SMP
+	bool "MIPS MT SMP support (1 TC on each available VPE)"
+	default y
+	depends on SYS_SUPPORTS_MULTITHREADING && !CPU_MIPSR6 && !CPU_MICROMIPS
+	select CPU_MIPSR2_IRQ_VI
+	select CPU_MIPSR2_IRQ_EI
+	select SYNC_R4K
+	select MIPS_MT
+	select SMP
+	select SMP_UP
+	select SYS_SUPPORTS_SMP
+	select SYS_SUPPORTS_SCHED_SMT
+	select MIPS_PERF_SHARED_TC_COUNTERS
+	help
+	  This is a kernel model which is known as SMVP. This is supported
+	  on cores with the MT ASE and uses the available VPEs to implement
+	  virtual processors which supports SMP. This is equivalent to the
+	  Intel Hyperthreading feature. For further information go to
+	  <http://www.imgtec.com/mips/mips-multithreading.asp>.
+
+config MIPS_MT
+	bool
+
+config SCHED_SMT
+	bool "SMT (multithreading) scheduler support"
+	depends on SYS_SUPPORTS_SCHED_SMT
+	default n
+	help
+	  SMT scheduler support improves the CPU scheduler's decision making
+	  when dealing with MIPS MT enabled cores at a cost of slightly
+	  increased overhead in some places. If unsure say N here.
+
+config SYS_SUPPORTS_SCHED_SMT
+	bool
+
+config SYS_SUPPORTS_MULTITHREADING
+	bool
+
+config MIPS_MT_FPAFF
+	bool "Dynamic FPU affinity for FP-intensive threads"
+	default y
+	depends on MIPS_MT_SMP
+
+config MIPSR2_TO_R6_EMULATOR
+	bool "MIPS R2-to-R6 emulator"
+	depends on CPU_MIPSR6
+	depends on MIPS_FP_SUPPORT
+	default y
+	help
+	  Choose this option if you want to run non-R6 MIPS userland code.
+	  Even if you say 'Y' here, the emulator will still be disabled by
+	  default. You can enable it using the 'mipsr2emu' kernel option.
+	  The only reason this is a build-time option is to save ~14K from the
+	  final kernel image.
+
+config SYS_SUPPORTS_VPE_LOADER
+	bool
+	depends on SYS_SUPPORTS_MULTITHREADING
+	help
+	  Indicates that the platform supports the VPE loader, and provides
+	  physical_memsize.
+
+config MIPS_VPE_LOADER
+	bool "VPE loader support."
+	depends on SYS_SUPPORTS_VPE_LOADER && MODULES
+	select CPU_MIPSR2_IRQ_VI
+	select CPU_MIPSR2_IRQ_EI
+	select MIPS_MT
+	help
+	  Includes a loader for loading an elf relocatable object
+	  onto another VPE and running it.
+
+config MIPS_VPE_LOADER_CMP
+	bool
+	default "y"
+	depends on MIPS_VPE_LOADER && MIPS_CMP
+
+config MIPS_VPE_LOADER_MT
+	bool
+	default "y"
+	depends on MIPS_VPE_LOADER && !MIPS_CMP
+
+config MIPS_VPE_LOADER_TOM
+	bool "Load VPE program into memory hidden from linux"
+	depends on MIPS_VPE_LOADER
+	default y
+	help
+	  The loader can use memory that is present but has been hidden from
+	  Linux using the kernel command line option "mem=xxMB". It's up to
+	  you to ensure the amount you put in the option and the space your
+	  program requires is less or equal to the amount physically present.
+
+config MIPS_VPE_APSP_API
+	bool "Enable support for AP/SP API (RTLX)"
+	depends on MIPS_VPE_LOADER
+
+config MIPS_VPE_APSP_API_CMP
+	bool
+	default "y"
+	depends on MIPS_VPE_APSP_API && MIPS_CMP
+
+config MIPS_VPE_APSP_API_MT
+	bool
+	default "y"
+	depends on MIPS_VPE_APSP_API && !MIPS_CMP
+
+config MIPS_CMP
+	bool "MIPS CMP framework support (DEPRECATED)"
+	depends on SYS_SUPPORTS_MIPS_CMP && !CPU_MIPSR6
+	select SMP
+	select SYNC_R4K
+	select SYS_SUPPORTS_SMP
+	select WEAK_ORDERING
+	default n
+	help
+	  Select this if you are using a bootloader which implements the "CMP
+	  framework" protocol (ie. YAMON) and want your kernel to make use of
+	  its ability to start secondary CPUs.
+
+	  Unless you have a specific need, you should use CONFIG_MIPS_CPS
+	  instead of this.
+
+config MIPS_CPS
+	bool "MIPS Coherent Processing System support"
+	depends on SYS_SUPPORTS_MIPS_CPS
+	select MIPS_CM
+	select MIPS_CPS_PM if HOTPLUG_CPU
+	select SMP
+	select SYNC_R4K if (CEVT_R4K || CSRC_R4K)
+	select SYS_SUPPORTS_HOTPLUG_CPU
+	select SYS_SUPPORTS_SCHED_SMT if CPU_MIPSR6
+	select SYS_SUPPORTS_SMP
+	select WEAK_ORDERING
+	select GENERIC_IRQ_MIGRATION if HOTPLUG_CPU
+	help
+	  Select this if you wish to run an SMP kernel across multiple cores
+	  within a MIPS Coherent Processing System. When this option is
+	  enabled the kernel will probe for other cores and boot them with
+	  no external assistance. It is safe to enable this when hardware
+	  support is unavailable.
+
+config MIPS_CPS_PM
+	depends on MIPS_CPS
+	bool
+
+config MIPS_CM
+	bool
+	select MIPS_CPC
+
+config MIPS_CPC
+	bool
+
+config SB1_PASS_2_WORKAROUNDS
+	bool
+	depends on CPU_SB1 && (CPU_SB1_PASS_2_2 || CPU_SB1_PASS_2)
+	default y
+
+config SB1_PASS_2_1_WORKAROUNDS
+	bool
+	depends on CPU_SB1 && CPU_SB1_PASS_2
+	default y
+
+choice
+	prompt "SmartMIPS or microMIPS ASE support"
+
+config CPU_NEEDS_NO_SMARTMIPS_OR_MICROMIPS
+	bool "None"
+	help
+	  Select this if you want neither microMIPS nor SmartMIPS support
+
+config CPU_HAS_SMARTMIPS
+	depends on SYS_SUPPORTS_SMARTMIPS
+	bool "SmartMIPS"
+	help
+	  SmartMIPS is a extension of the MIPS32 architecture aimed at
+	  increased security at both hardware and software level for
+	  smartcards.  Enabling this option will allow proper use of the
+	  SmartMIPS instructions by Linux applications.  However a kernel with
+	  this option will not work on a MIPS core without SmartMIPS core.  If
+	  you don't know you probably don't have SmartMIPS and should say N
+	  here.
+
+config CPU_MICROMIPS
+	depends on 32BIT && SYS_SUPPORTS_MICROMIPS && !CPU_MIPSR6
+	bool "microMIPS"
+	help
+	  When this option is enabled the kernel will be built using the
+	  microMIPS ISA
+
+endchoice
+
+config CPU_HAS_MSA
+	bool "Support for the MIPS SIMD Architecture"
+	depends on CPU_SUPPORTS_MSA
+	depends on MIPS_FP_SUPPORT
+	depends on 64BIT || MIPS_O32_FP64_SUPPORT
+	help
+	  MIPS SIMD Architecture (MSA) introduces 128 bit wide vector registers
+	  and a set of SIMD instructions to operate on them. When this option
+	  is enabled the kernel will support allocating & switching MSA
+	  vector register contexts. If you know that your kernel will only be
+	  running on CPUs which do not support MSA or that your userland will
+	  not be making use of it then you may wish to say N here to reduce
+	  the size & complexity of your kernel.
+
+	  If unsure, say Y.
+
+config CPU_HAS_WB
+	bool
+
+config XKS01
+	bool
+
+config CPU_HAS_DIEI
+	depends on !CPU_DIEI_BROKEN
+	bool
+
+config CPU_DIEI_BROKEN
+	bool
+
+config CPU_HAS_RIXI
+	bool
+
+config CPU_NO_LOAD_STORE_LR
+	bool
+	help
+	  CPU lacks support for unaligned load and store instructions:
+	  LWL, LWR, SWL, SWR (Load/store word left/right).
+	  LDL, LDR, SDL, SDR (Load/store doubleword left/right, for 64bit
+	  systems).
+
+#
+# Vectored interrupt mode is an R2 feature
+#
+config CPU_MIPSR2_IRQ_VI
+	bool
+
+#
+# Extended interrupt mode is an R2 feature
+#
+config CPU_MIPSR2_IRQ_EI
+	bool
+
+config CPU_HAS_SYNC
+	bool
+	depends on !CPU_R3000
+	default y
+
+#
+# CPU non-features
+#
+
+# Work around the "daddi" and "daddiu" CPU errata:
+#
+# - The `daddi' instruction fails to trap on overflow.
+#   "MIPS R4000PC/SC Errata, Processor Revision 2.2 and 3.0",
+#   erratum #23
+#
+# - The `daddiu' instruction can produce an incorrect result.
+#   "MIPS R4000PC/SC Errata, Processor Revision 2.2 and 3.0",
+#   erratum #41
+#   "MIPS R4000MC Errata, Processor Revision 2.2 and 3.0", erratum
+#   #15
+#   "MIPS R4400PC/SC Errata, Processor Revision 1.0", erratum #7
+#   "MIPS R4400MC Errata, Processor Revision 1.0", erratum #5
+config CPU_DADDI_WORKAROUNDS
+	bool
+
+# Work around certain R4000 CPU errata (as implemented by GCC):
+#
+# - A double-word or a variable shift may give an incorrect result
+#   if executed immediately after starting an integer division:
+#   "MIPS R4000PC/SC Errata, Processor Revision 2.2 and 3.0",
+#   erratum #28
+#   "MIPS R4000MC Errata, Processor Revision 2.2 and 3.0", erratum
+#   #19
+#
+# - A double-word or a variable shift may give an incorrect result
+#   if executed while an integer multiplication is in progress:
+#   "MIPS R4000PC/SC Errata, Processor Revision 2.2 and 3.0",
+#   errata #16 & #28
+#
+# - An integer division may give an incorrect result if started in
+#   a delay slot of a taken branch or a jump:
+#   "MIPS R4000PC/SC Errata, Processor Revision 2.2 and 3.0",
+#   erratum #52
+config CPU_R4000_WORKAROUNDS
+	bool
+	select CPU_R4400_WORKAROUNDS
+
+# Work around certain R4400 CPU errata (as implemented by GCC):
+#
+# - A double-word or a variable shift may give an incorrect result
+#   if executed immediately after starting an integer division:
+#   "MIPS R4400MC Errata, Processor Revision 1.0", erratum #10
+#   "MIPS R4400MC Errata, Processor Revision 2.0 & 3.0", erratum #4
+config CPU_R4400_WORKAROUNDS
+	bool
+
+config CPU_R4X00_BUGS64
+	bool
+	default y if SYS_HAS_CPU_R4X00 && 64BIT && (TARGET_ISA_REV < 1)
+
+config MIPS_ASID_SHIFT
+	int
+	default 6 if CPU_R3000
+	default 0
+
+config MIPS_ASID_BITS
+	int
+	default 0 if MIPS_ASID_BITS_VARIABLE
+	default 6 if CPU_R3000
+	default 8
+
+config MIPS_ASID_BITS_VARIABLE
+	bool
+
+config MIPS_CRC_SUPPORT
+	bool
+
+# R4600 erratum.  Due to the lack of errata information the exact
+# technical details aren't known.  I've experimentally found that disabling
+# interrupts during indexed I-cache flushes seems to be sufficient to deal
+# with the issue.
+config WAR_R4600_V1_INDEX_ICACHEOP
+	bool
+
+# Pleasures of the R4600 V1.x.  Cite from the IDT R4600 V1.7 errata:
+#
+#  18. The CACHE instructions Hit_Writeback_Invalidate_D, Hit_Writeback_D,
+#      Hit_Invalidate_D and Create_Dirty_Excl_D should only be
+#      executed if there is no other dcache activity. If the dcache is
+#      accessed for another instruction immediately preceding when these
+#      cache instructions are executing, it is possible that the dcache
+#      tag match outputs used by these cache instructions will be
+#      incorrect. These cache instructions should be preceded by at least
+#      four instructions that are not any kind of load or store
+#      instruction.
+#
+#      This is not allowed:    lw
+#                              nop
+#                              nop
+#                              nop
+#                              cache       Hit_Writeback_Invalidate_D
+#
+#      This is allowed:        lw
+#                              nop
+#                              nop
+#                              nop
+#                              nop
+#                              cache       Hit_Writeback_Invalidate_D
+config WAR_R4600_V1_HIT_CACHEOP
+	bool
+
+# Writeback and invalidate the primary cache dcache before DMA.
+#
+# R4600 v2.0 bug: "The CACHE instructions Hit_Writeback_Inv_D,
+# Hit_Writeback_D, Hit_Invalidate_D and Create_Dirty_Exclusive_D will only
+# operate correctly if the internal data cache refill buffer is empty.  These
+# CACHE instructions should be separated from any potential data cache miss
+# by a load instruction to an uncached address to empty the response buffer."
+# (Revision 2.0 device errata from IDT available on https://www.idt.com/
+# in .pdf format.)
+config WAR_R4600_V2_HIT_CACHEOP
+	bool
+
+# From TX49/H2 manual: "If the instruction (i.e. CACHE) is issued for
+# the line which this instruction itself exists, the following
+# operation is not guaranteed."
+#
+# Workaround: do two phase flushing for Index_Invalidate_I
+config WAR_TX49XX_ICACHE_INDEX_INV
+	bool
+
+# The RM7000 processors and the E9000 cores have a bug (though PMC-Sierra
+# opposes it being called that) where invalid instructions in the same
+# I-cache line worth of instructions being fetched may case spurious
+# exceptions.
+config WAR_ICACHE_REFILLS
+	bool
+
+# On the R10000 up to version 2.6 (not sure about 2.7) there is a bug that
+# may cause ll / sc and lld / scd sequences to execute non-atomically.
+config WAR_R10000_LLSC
+	bool
+
+# 34K core erratum: "Problems Executing the TLBR Instruction"
+config WAR_MIPS34K_MISSED_ITLB
+	bool
+
+#
+# - Highmem only makes sense for the 32-bit kernel.
+# - The current highmem code will only work properly on physically indexed
+#   caches such as R3000, SB1, R7000 or those that look like they're virtually
+#   indexed such as R4000/R4400 SC and MC versions or R10000.  So for the
+#   moment we protect the user and offer the highmem option only on machines
+#   where it's known to be safe.  This will not offer highmem on a few systems
+#   such as MIPS32 and MIPS64 CPUs which may have virtual and physically
+#   indexed CPUs but we're playing safe.
+# - We use SYS_SUPPORTS_HIGHMEM to offer highmem only for systems where we
+#   know they might have memory configurations that could make use of highmem
+#   support.
+#
+config HIGHMEM
+	bool "High Memory Support"
+	depends on 32BIT && CPU_SUPPORTS_HIGHMEM && SYS_SUPPORTS_HIGHMEM && !CPU_MIPS32_3_5_EVA
+	select KMAP_LOCAL
+
+config CPU_SUPPORTS_HIGHMEM
+	bool
+
+config SYS_SUPPORTS_HIGHMEM
+	bool
+
+config SYS_SUPPORTS_SMARTMIPS
+	bool
+
+config SYS_SUPPORTS_MICROMIPS
+	bool
+
+config SYS_SUPPORTS_MIPS16
+	bool
+	help
+	  This option must be set if a kernel might be executed on a MIPS16-
+	  enabled CPU even if MIPS16 is not actually being used.  In other
+	  words, it makes the kernel MIPS16-tolerant.
+
+config CPU_SUPPORTS_MSA
+	bool
+
+config ARCH_FLATMEM_ENABLE
+	def_bool y
+	depends on !NUMA && !CPU_LOONGSON2EF
+
+config ARCH_SPARSEMEM_ENABLE
+	bool
+
+config NUMA
+	bool "NUMA Support"
+	depends on SYS_SUPPORTS_NUMA
+	select SMP
+	select HAVE_SETUP_PER_CPU_AREA
+	select NEED_PER_CPU_EMBED_FIRST_CHUNK
+	help
+	  Say Y to compile the kernel to support NUMA (Non-Uniform Memory
+	  Access).  This option improves performance on systems with more
+	  than two nodes; on two node systems it is generally better to
+	  leave it disabled; on single node systems leave this option
+	  disabled.
+
+config SYS_SUPPORTS_NUMA
+	bool
+
+config HAVE_ARCH_NODEDATA_EXTENSION
+	bool
+
+config RELOCATABLE
+	bool "Relocatable kernel"
+	depends on SYS_SUPPORTS_RELOCATABLE
+	depends on CPU_MIPS32_R2 || CPU_MIPS64_R2 || \
+		   CPU_MIPS32_R5 || CPU_MIPS64_R5 || \
+		   CPU_MIPS32_R6 || CPU_MIPS64_R6 || \
+		   CPU_P5600 || CAVIUM_OCTEON_SOC || \
+		   CPU_LOONGSON64
+	help
+	  This builds a kernel image that retains relocation information
+	  so it can be loaded someplace besides the default 1MB.
+	  The relocations make the kernel binary about 15% larger,
+	  but are discarded at runtime
+
+config RELOCATION_TABLE_SIZE
+	hex "Relocation table size"
+	depends on RELOCATABLE
+	range 0x0 0x01000000
+	default "0x00200000" if CPU_LOONGSON64
+	default "0x00100000"
+	help
+	  A table of relocation data will be appended to the kernel binary
+	  and parsed at boot to fix up the relocated kernel.
+
+	  This option allows the amount of space reserved for the table to be
+	  adjusted, although the default of 1Mb should be ok in most cases.
+
+	  The build will fail and a valid size suggested if this is too small.
+
+	  If unsure, leave at the default value.
+
+config RANDOMIZE_BASE
+	bool "Randomize the address of the kernel image"
+	depends on RELOCATABLE
+	help
+	  Randomizes the physical and virtual address at which the
+	  kernel image is loaded, as a security feature that
+	  deters exploit attempts relying on knowledge of the location
+	  of kernel internals.
+
+	  Entropy is generated using any coprocessor 0 registers available.
+
+	  The kernel will be offset by up to RANDOMIZE_BASE_MAX_OFFSET.
+
+	  If unsure, say N.
+
+config RANDOMIZE_BASE_MAX_OFFSET
+	hex "Maximum kASLR offset" if EXPERT
+	depends on RANDOMIZE_BASE
+	range 0x0 0x40000000 if EVA || 64BIT
+	range 0x0 0x08000000
+	default "0x01000000"
+	help
+	  When kASLR is active, this provides the maximum offset that will
+	  be applied to the kernel image. It should be set according to the
+	  amount of physical RAM available in the target system minus
+	  PHYSICAL_START and must be a power of 2.
+
+	  This is limited by the size of KSEG0, 256Mb on 32-bit or 1Gb with
+	  EVA or 64-bit. The default is 16Mb.
+
+config NODES_SHIFT
+	int
+	default "6"
+	depends on NUMA
+
+config HW_PERF_EVENTS
+	bool "Enable hardware performance counter support for perf events"
+	depends on PERF_EVENTS && (CPU_MIPS32 || CPU_MIPS64 || CPU_R10000 || CPU_SB1 || CPU_CAVIUM_OCTEON || CPU_LOONGSON64)
+	default y
+	help
+	  Enable hardware performance counter support for perf events. If
+	  disabled, perf events will use software events only.
+
+config DMI
+	bool "Enable DMI scanning"
+	depends on MACH_LOONGSON64
+	select DMI_SCAN_MACHINE_NON_EFI_FALLBACK
+	default y
+	help
+	  Enabled scanning of DMI to identify machine quirks. Say Y
+	  here unless you have verified that your setup is not
+	  affected by entries in the DMI blacklist. Required by PNP
+	  BIOS code.
+
+config SMP
+	bool "Multi-Processing support"
+	depends on SYS_SUPPORTS_SMP
+	help
+	  This enables support for systems with more than one CPU. If you have
+	  a system with only one CPU, say N. If you have a system with more
+	  than one CPU, say Y.
+
+	  If you say N here, the kernel will run on uni- and multiprocessor
+	  machines, but will use only one CPU of a multiprocessor machine. If
+	  you say Y here, the kernel will run on many, but not all,
+	  uniprocessor machines. On a uniprocessor machine, the kernel
+	  will run faster if you say N here.
+
+	  People using multiprocessor machines who say Y here should also say
+	  Y to "Enhanced Real Time Clock Support", below.
+
+	  See also the SMP-HOWTO available at
+	  <https://www.tldp.org/docs.html#howto>.
+
+	  If you don't know what to do here, say N.
+
+config HOTPLUG_CPU
+	bool "Support for hot-pluggable CPUs"
+	depends on SMP && SYS_SUPPORTS_HOTPLUG_CPU
+	help
+	  Say Y here to allow turning CPUs off and on. CPUs can be
+	  controlled through /sys/devices/system/cpu.
+	  (Note: power management support will enable this option
+	    automatically on SMP systems. )
+	  Say N if you want to disable CPU hotplug.
+
+config SMP_UP
+	bool
+
+config SYS_SUPPORTS_MIPS_CMP
+	bool
+
+config SYS_SUPPORTS_MIPS_CPS
+	bool
+
+config SYS_SUPPORTS_SMP
+	bool
+
+config NR_CPUS_DEFAULT_4
+	bool
+
+config NR_CPUS_DEFAULT_8
+	bool
+
+config NR_CPUS_DEFAULT_16
+	bool
+
+config NR_CPUS_DEFAULT_32
+	bool
+
+config NR_CPUS_DEFAULT_64
+	bool
+
+config NR_CPUS
+	int "Maximum number of CPUs (2-256)"
+	range 2 256
+	depends on SMP
+	default "4" if NR_CPUS_DEFAULT_4
+	default "8" if NR_CPUS_DEFAULT_8
+	default "16" if NR_CPUS_DEFAULT_16
+	default "32" if NR_CPUS_DEFAULT_32
+	default "64" if NR_CPUS_DEFAULT_64
+	help
+	  This allows you to specify the maximum number of CPUs which this
+	  kernel will support.  The maximum supported value is 32 for 32-bit
+	  kernel and 64 for 64-bit kernels; the minimum value which makes
+	  sense is 1 for Qemu (useful only for kernel debugging purposes)
+	  and 2 for all others.
+
+	  This is purely to save memory - each supported CPU adds
+	  approximately eight kilobytes to the kernel image.  For best
+	  performance should round up your number of processors to the next
+	  power of two.
+
+config MIPS_PERF_SHARED_TC_COUNTERS
+	bool
+
+config MIPS_NR_CPU_NR_MAP_1024
+	bool
+
+config MIPS_NR_CPU_NR_MAP
+	int
+	depends on SMP
+	default 1024 if MIPS_NR_CPU_NR_MAP_1024
+	default NR_CPUS if !MIPS_NR_CPU_NR_MAP_1024
+
+#
+# Timer Interrupt Frequency Configuration
+#
+
+choice
+	prompt "Timer frequency"
+	default HZ_250
+	help
+	  Allows the configuration of the timer frequency.
+
+	config HZ_24
+		bool "24 HZ" if SYS_SUPPORTS_24HZ || SYS_SUPPORTS_ARBIT_HZ
+
+	config HZ_48
+		bool "48 HZ" if SYS_SUPPORTS_48HZ || SYS_SUPPORTS_ARBIT_HZ
+
+	config HZ_100
+		bool "100 HZ" if SYS_SUPPORTS_100HZ || SYS_SUPPORTS_ARBIT_HZ
+
+	config HZ_128
+		bool "128 HZ" if SYS_SUPPORTS_128HZ || SYS_SUPPORTS_ARBIT_HZ
+
+	config HZ_250
+		bool "250 HZ" if SYS_SUPPORTS_250HZ || SYS_SUPPORTS_ARBIT_HZ
+
+	config HZ_256
+		bool "256 HZ" if SYS_SUPPORTS_256HZ || SYS_SUPPORTS_ARBIT_HZ
+
+	config HZ_1000
+		bool "1000 HZ" if SYS_SUPPORTS_1000HZ || SYS_SUPPORTS_ARBIT_HZ
+
+	config HZ_1024
+		bool "1024 HZ" if SYS_SUPPORTS_1024HZ || SYS_SUPPORTS_ARBIT_HZ
+
+endchoice
+
+config SYS_SUPPORTS_24HZ
+	bool
+
+config SYS_SUPPORTS_48HZ
+	bool
+
+config SYS_SUPPORTS_100HZ
+	bool
+
+config SYS_SUPPORTS_128HZ
+	bool
+
+config SYS_SUPPORTS_250HZ
+	bool
+
+config SYS_SUPPORTS_256HZ
+	bool
+
+config SYS_SUPPORTS_1000HZ
+	bool
+
+config SYS_SUPPORTS_1024HZ
+	bool
+
+config SYS_SUPPORTS_ARBIT_HZ
+	bool
+	default y if !SYS_SUPPORTS_24HZ && \
+		     !SYS_SUPPORTS_48HZ && \
+		     !SYS_SUPPORTS_100HZ && \
+		     !SYS_SUPPORTS_128HZ && \
+		     !SYS_SUPPORTS_250HZ && \
+		     !SYS_SUPPORTS_256HZ && \
+		     !SYS_SUPPORTS_1000HZ && \
+		     !SYS_SUPPORTS_1024HZ
+
+config HZ
+	int
+	default 24 if HZ_24
+	default 48 if HZ_48
+	default 100 if HZ_100
+	default 128 if HZ_128
+	default 250 if HZ_250
+	default 256 if HZ_256
+	default 1000 if HZ_1000
+	default 1024 if HZ_1024
+
+config SCHED_HRTICK
+	def_bool HIGH_RES_TIMERS
+
+config KEXEC
+	bool "Kexec system call"
+	select KEXEC_CORE
+	help
+	  kexec is a system call that implements the ability to shutdown your
+	  current kernel, and to start another kernel.  It is like a reboot
+	  but it is independent of the system firmware.   And like a reboot
+	  you can start any kernel with it, not just Linux.
+
+	  The name comes from the similarity to the exec system call.
+
+	  It is an ongoing process to be certain the hardware in a machine
+	  is properly shutdown, so do not be surprised if this code does not
+	  initially work for you.  As of this writing the exact hardware
+	  interface is strongly in flux, so no good recommendation can be
+	  made.
+
+config CRASH_DUMP
+	bool "Kernel crash dumps"
+	help
+	  Generate crash dump after being started by kexec.
+	  This should be normally only set in special crash dump kernels
+	  which are loaded in the main kernel with kexec-tools into
+	  a specially reserved region and then later executed after
+	  a crash by kdump/kexec. The crash dump kernel must be compiled
+	  to a memory address not used by the main kernel or firmware using
+	  PHYSICAL_START.
+
+config PHYSICAL_START
+	hex "Physical address where the kernel is loaded"
+	default "0xffffffff84000000"
+	depends on CRASH_DUMP
+	help
+	  This gives the CKSEG0 or KSEG0 address where the kernel is loaded.
+	  If you plan to use kernel for capturing the crash dump change
+	  this value to start of the reserved region (the "X" value as
+	  specified in the "crashkernel=YM@XM" command line boot parameter
+	  passed to the panic-ed kernel).
+
+config MIPS_O32_FP64_SUPPORT
+	bool "Support for O32 binaries using 64-bit FP" if !CPU_MIPSR6
+	depends on 32BIT || MIPS32_O32
+	help
+	  When this is enabled, the kernel will support use of 64-bit floating
+	  point registers with binaries using the O32 ABI along with the
+	  EF_MIPS_FP64 ELF header flag (typically built with -mfp64). On
+	  32-bit MIPS systems this support is at the cost of increasing the
+	  size and complexity of the compiled FPU emulator. Thus if you are
+	  running a MIPS32 system and know that none of your userland binaries
+	  will require 64-bit floating point, you may wish to reduce the size
+	  of your kernel & potentially improve FP emulation performance by
+	  saying N here.
+
+	  Although binutils currently supports use of this flag the details
+	  concerning its effect upon the O32 ABI in userland are still being
+	  worked on. In order to avoid userland becoming dependent upon current
+	  behaviour before the details have been finalised, this option should
+	  be considered experimental and only enabled by those working upon
+	  said details.
+
+	  If unsure, say N.
+
+config USE_OF
+	bool
+	select OF
+	select OF_EARLY_FLATTREE
+	select IRQ_DOMAIN
+
+config UHI_BOOT
+	bool
+
+config BUILTIN_DTB
+	bool
+
+choice
+	prompt "Kernel appended dtb support" if USE_OF
+	default MIPS_NO_APPENDED_DTB
+
+	config MIPS_NO_APPENDED_DTB
+		bool "None"
+		help
+		  Do not enable appended dtb support.
+
+	config MIPS_ELF_APPENDED_DTB
+		bool "vmlinux"
+		help
+		  With this option, the boot code will look for a device tree binary
+		  DTB) included in the vmlinux ELF section .appended_dtb. By default
+		  it is empty and the DTB can be appended using binutils command
+		  objcopy:
+
+		    objcopy --update-section .appended_dtb=<filename>.dtb vmlinux
+
+		  This is meant as a backward compatibility convenience for those
+		  systems with a bootloader that can't be upgraded to accommodate
+		  the documented boot protocol using a device tree.
+
+	config MIPS_RAW_APPENDED_DTB
+		bool "vmlinux.bin or vmlinuz.bin"
+		help
+		  With this option, the boot code will look for a device tree binary
+		  DTB) appended to raw vmlinux.bin or vmlinuz.bin.
+		  (e.g. cat vmlinux.bin <filename>.dtb > vmlinux_w_dtb).
+
+		  This is meant as a backward compatibility convenience for those
+		  systems with a bootloader that can't be upgraded to accommodate
+		  the documented boot protocol using a device tree.
+
+		  Beware that there is very little in terms of protection against
+		  this option being confused by leftover garbage in memory that might
+		  look like a DTB header after a reboot if no actual DTB is appended
+		  to vmlinux.bin.  Do not leave this option active in a production kernel
+		  if you don't intend to always append a DTB.
+endchoice
+
+choice
+	prompt "Kernel command line type" if !CMDLINE_OVERRIDE
+	default MIPS_CMDLINE_FROM_DTB if USE_OF && !ATH79 && !MACH_INGENIC && \
+					 !MACH_LOONGSON64 && !MIPS_MALTA && \
+					 !CAVIUM_OCTEON_SOC
+	default MIPS_CMDLINE_FROM_BOOTLOADER
+
+	config MIPS_CMDLINE_FROM_DTB
+		depends on USE_OF
+		bool "Dtb kernel arguments if available"
+
+	config MIPS_CMDLINE_DTB_EXTEND
+		depends on USE_OF
+		bool "Extend dtb kernel arguments with bootloader arguments"
+
+	config MIPS_CMDLINE_FROM_BOOTLOADER
+		bool "Bootloader kernel arguments if available"
+
+	config MIPS_CMDLINE_BUILTIN_EXTEND
+		depends on CMDLINE_BOOL
+		bool "Extend builtin kernel arguments with bootloader arguments"
+endchoice
+
+endmenu
+
+config LOCKDEP_SUPPORT
+	bool
+	default y
+
+config STACKTRACE_SUPPORT
+	bool
+	default y
+
+config PGTABLE_LEVELS
+	int
+	default 4 if PAGE_SIZE_4KB && MIPS_VA_BITS_48
+	default 3 if 64BIT && (!PAGE_SIZE_64KB || MIPS_VA_BITS_48)
+	default 2
+
+config MIPS_AUTO_PFN_OFFSET
+	bool
+
+menu "Bus options (PCI, PCMCIA, EISA, ISA, TC)"
+
+config PCI_DRIVERS_GENERIC
+	select PCI_DOMAINS_GENERIC if PCI
+	bool
+
+config PCI_DRIVERS_LEGACY
+	def_bool !PCI_DRIVERS_GENERIC
+	select NO_GENERIC_PCI_IOPORT_MAP
+	select PCI_DOMAINS if PCI
+
+#
+# ISA support is now enabled via select.  Too many systems still have the one
+# or other ISA chip on the board that users don't know about so don't expect
+# users to choose the right thing ...
+#
+config ISA
+	bool
+
+config TC
+	bool "TURBOchannel support"
+	depends on MACH_DECSTATION
+	help
+	  TURBOchannel is a DEC (now Compaq (now HP)) bus for Alpha and MIPS
+	  processors.  TURBOchannel programming specifications are available
+	  at:
+	  <ftp://ftp.hp.com/pub/alphaserver/archive/triadd/>
+	  and:
+	  <http://www.computer-refuge.org/classiccmp/ftp.digital.com/pub/DEC/TriAdd/>
+	  Linux driver support status is documented at:
+	  <http://www.linux-mips.org/wiki/DECstation>
+
+config MMU
+	bool
+	default y
+
+config ARCH_MMAP_RND_BITS_MIN
+	default 12 if 64BIT
+	default 8
+
+config ARCH_MMAP_RND_BITS_MAX
+	default 18 if 64BIT
+	default 15
+
+config ARCH_MMAP_RND_COMPAT_BITS_MIN
+	default 8
+
+config ARCH_MMAP_RND_COMPAT_BITS_MAX
+	default 15
+
+config I8253
+	bool
+	select CLKSRC_I8253
+	select CLKEVT_I8253
+	select MIPS_EXTERNAL_TIMER
+endmenu
+
+config TRAD_SIGNALS
+	bool
+
+config MIPS32_COMPAT
+	bool
+
+config COMPAT
+	bool
+
+config MIPS32_O32
+	bool "Kernel support for o32 binaries"
+	depends on 64BIT
+	select ARCH_WANT_OLD_COMPAT_IPC
+	select COMPAT
+	select MIPS32_COMPAT
+	help
+	  Select this option if you want to run o32 binaries.  These are pure
+	  32-bit binaries as used by the 32-bit Linux/MIPS port.  Most of
+	  existing binaries are in this format.
+
+	  If unsure, say Y.
+
+config MIPS32_N32
+	bool "Kernel support for n32 binaries"
+	depends on 64BIT
+	select ARCH_WANT_COMPAT_IPC_PARSE_VERSION
+	select COMPAT
+	select MIPS32_COMPAT
+	help
+	  Select this option if you want to run n32 binaries.  These are
+	  64-bit binaries using 32-bit quantities for addressing and certain
+	  data that would normally be 64-bit.  They are used in special
+	  cases.
+
+	  If unsure, say N.
+
+config CC_HAS_MNO_BRANCH_LIKELY
+	def_bool y
+	depends on $(cc-option,-mno-branch-likely)
+
+menu "Power management options"
+
+config ARCH_HIBERNATION_POSSIBLE
+	def_bool y
+	depends on SYS_SUPPORTS_HOTPLUG_CPU || !SMP
+
+config ARCH_SUSPEND_POSSIBLE
+	def_bool y
+	depends on SYS_SUPPORTS_HOTPLUG_CPU || !SMP
+
+source "kernel/power/Kconfig"
+
+endmenu
+
+config MIPS_EXTERNAL_TIMER
+	bool
+
+menu "CPU Power Management"
+
+if CPU_SUPPORTS_CPUFREQ && MIPS_EXTERNAL_TIMER
+source "drivers/cpufreq/Kconfig"
+endif # CPU_SUPPORTS_CPUFREQ && MIPS_EXTERNAL_TIMER
+
+source "drivers/cpuidle/Kconfig"
+
+endmenu
+
+source "arch/mips/kvm/Kconfig"
+
+source "arch/mips/vdso/Kconfig"
diff --git a/arch/mips/Kconfig.debug b/arch/mips/Kconfig.debug
new file mode 100644
index 000000000..f4ae7900f
--- /dev/null
+++ b/arch/mips/Kconfig.debug
@@ -0,0 +1,166 @@
+# SPDX-License-Identifier: GPL-2.0
+
+config EARLY_PRINTK
+	bool "Early printk" if EXPERT
+	depends on SYS_HAS_EARLY_PRINTK
+	default y
+	help
+	  This option enables special console drivers which allow the kernel
+	  to print messages very early in the bootup process.
+
+	  This is useful for kernel debugging when your machine crashes very
+	  early before the console code is initialized. For normal operation,
+	  it is not recommended because it looks ugly on some machines and
+	  doesn't cooperate with an X server. You should normally say N here,
+	  unless you want to debug such a crash.
+
+config EARLY_PRINTK_8250
+	bool
+	depends on EARLY_PRINTK && USE_GENERIC_EARLY_PRINTK_8250
+	default y
+	help
+	  "8250/16550 and compatible serial early printk driver"
+	  If you say Y here, it will be possible to use a 8250/16550 serial
+	  port as the boot console.
+
+config USE_GENERIC_EARLY_PRINTK_8250
+	bool
+
+config CMDLINE_BOOL
+	bool "Built-in kernel command line"
+	help
+	  For most systems, it is firmware or second stage bootloader that
+	  by default specifies the kernel command line options.  However,
+	  it might be necessary or advantageous to either override the
+	  default kernel command line or add a few extra options to it.
+	  For such cases, this option allows you to hardcode your own
+	  command line options directly into the kernel.  For that, you
+	  should choose 'Y' here, and fill in the extra boot arguments
+	  in CONFIG_CMDLINE.
+
+	  The built-in options will be concatenated to the default command
+	  line if CMDLINE_OVERRIDE is set to 'N'. Otherwise, the default
+	  command line will be ignored and replaced by the built-in string.
+
+	  Most MIPS systems will normally expect 'N' here and rely upon
+	  the command line from the firmware or the second-stage bootloader.
+
+config CMDLINE
+	string "Default kernel command string"
+	depends on CMDLINE_BOOL
+	help
+	  On some platforms, there is currently no way for the boot loader to
+	  pass arguments to the kernel.  For these platforms, and for the cases
+	  when you want to add some extra options to the command line or ignore
+	  the default command line, you can supply some command-line options at
+	  build time by entering them here.  In other cases you can specify
+	  kernel args so that you don't have to set them up in board prom
+	  initialization routines.
+
+	  For more information, see the CMDLINE_BOOL and CMDLINE_OVERRIDE
+	  options.
+
+config CMDLINE_OVERRIDE
+	bool "Built-in command line overrides firmware arguments"
+	depends on CMDLINE_BOOL
+	help
+	  By setting this option to 'Y' you will have your kernel ignore
+	  command line arguments from firmware or second stage bootloader.
+	  Instead, the built-in command line will be used exclusively.
+
+	  Normally, you will choose 'N' here.
+
+config SB1XXX_CORELIS
+	bool "Corelis Debugger"
+	depends on SIBYTE_SB1xxx_SOC
+	select DEBUG_KERNEL if !COMPILE_TEST
+	select DEBUG_INFO if !COMPILE_TEST
+	help
+	  Select compile flags that produce code that can be processed by the
+	  Corelis mksym utility and UDB Emulator.
+
+config DEBUG_ZBOOT
+	bool "Enable compressed kernel support debugging"
+	depends on DEBUG_KERNEL && SYS_SUPPORTS_ZBOOT
+	default n
+	help
+	  If you want to add compressed kernel support to a new board, and the
+	  board supports uart16550 compatible serial port, please select
+	  SYS_SUPPORTS_ZBOOT_UART16550 for your board and enable this option to
+	  debug it.
+
+	  If your board doesn't support uart16550 compatible serial port, you
+	  can try to select SYS_SUPPORTS_ZBOOT and use the other methods to
+	  debug it. for example, add a new serial port support just as
+	  arch/mips/boot/compressed/uart-16550.c does.
+
+	  After the compressed kernel support works, please disable this option
+	  to reduce the kernel image size and speed up the booting procedure a
+	  little.
+
+config ZBOOT_INGENIC_UART
+	int "UART to use for compressed kernel debugging"
+	depends on DEBUG_ZBOOT && MACH_INGENIC_SOC
+	default 0
+	range 0 4
+	help
+	  Specify the UART that should be used for compressed kernel debugging.
+
+config SPINLOCK_TEST
+	bool "Enable spinlock timing tests in debugfs"
+	depends on DEBUG_FS
+	default n
+	help
+	  Add several files to the debugfs to test spinlock speed.
+
+config SCACHE_DEBUGFS
+	bool "L2 cache debugfs entries"
+	depends on DEBUG_FS
+	help
+	  Enable this to allow parts of the L2 cache configuration, such as
+	  whether or not prefetching is enabled, to be exposed to userland
+	  via debugfs.
+
+	  If unsure, say N.
+
+menuconfig MIPS_CPS_NS16550_BOOL
+	bool "CPS SMP NS16550 UART output"
+	depends on MIPS_CPS
+	help
+	  Output debug information via an ns16550 compatible UART if exceptions
+	  occur early in the boot process of a secondary core.
+
+if MIPS_CPS_NS16550_BOOL
+
+config MIPS_CPS_NS16550
+	def_bool MIPS_CPS_NS16550_BASE != 0
+
+config MIPS_CPS_NS16550_BASE
+	hex "UART Base Address"
+	default 0x1b0003f8 if MIPS_MALTA
+	default 0
+	help
+	  The base address of the ns16550 compatible UART on which to output
+	  debug information from the early stages of core startup.
+
+	  This is only used if non-zero.
+
+config MIPS_CPS_NS16550_SHIFT
+	int "UART Register Shift"
+	default 0
+	help
+	  The number of bits to shift ns16550 register indices by in order to
+	  form their addresses. That is, log base 2 of the span between
+	  adjacent ns16550 registers in the system.
+
+config MIPS_CPS_NS16550_WIDTH
+	int "UART Register Width"
+	default 1
+	help
+	  ns16550 registers width. UART registers IO access methods will be
+	  selected in accordance with this parameter. By setting it to 1, 2 or
+	  4 UART registers will be accessed by means of lb/sb, lh/sh or lw/sw
+	  instructions respectively. Any value not from that set activates
+	  lb/sb instructions.
+
+endif # MIPS_CPS_NS16550_BOOL
diff --git a/arch/mips/Makefile b/arch/mips/Makefile
new file mode 100644
index 000000000..dd6486097
--- /dev/null
+++ b/arch/mips/Makefile
@@ -0,0 +1,588 @@
+#
+# This file is subject to the terms and conditions of the GNU General Public
+# License.  See the file "COPYING" in the main directory of this archive
+# for more details.
+#
+# Copyright (C) 1994, 95, 96, 2003 by Ralf Baechle
+# DECStation modifications by Paul M. Antoine, 1996
+# Copyright (C) 2002, 2003, 2004  Maciej W. Rozycki
+#
+# This file is included by the global makefile so that you can add your own
+# architecture-specific flags and dependencies.
+#
+
+archscripts: scripts_basic
+	$(Q)$(MAKE) $(build)=arch/mips/tools elf-entry
+ifeq ($(CONFIG_CPU_LOONGSON3_WORKAROUNDS),y)
+	$(Q)$(MAKE) $(build)=arch/mips/tools loongson3-llsc-check
+endif
+	$(Q)$(MAKE) $(build)=arch/mips/boot/tools relocs
+
+KBUILD_DEFCONFIG := 32r2el_defconfig
+KBUILD_DTBS      := dtbs
+
+#
+# Select the object file format to substitute into the linker script.
+#
+ifdef CONFIG_CPU_LITTLE_ENDIAN
+32bit-tool-archpref	= mipsel
+64bit-tool-archpref	= mips64el
+32bit-bfd		= elf32-tradlittlemips
+64bit-bfd		= elf64-tradlittlemips
+32bit-emul		= elf32ltsmip
+64bit-emul		= elf64ltsmip
+else
+32bit-tool-archpref	= mips
+64bit-tool-archpref	= mips64
+32bit-bfd		= elf32-tradbigmips
+64bit-bfd		= elf64-tradbigmips
+32bit-emul		= elf32btsmip
+64bit-emul		= elf64btsmip
+endif
+
+ifdef CONFIG_32BIT
+tool-archpref		= $(32bit-tool-archpref)
+UTS_MACHINE		:= mips
+endif
+ifdef CONFIG_64BIT
+tool-archpref		= $(64bit-tool-archpref)
+UTS_MACHINE		:= mips64
+endif
+
+ifdef cross_compiling
+  ifeq ($(CROSS_COMPILE),)
+    CROSS_COMPILE := $(call cc-cross-prefix, $(tool-archpref)-linux-  $(tool-archpref)-linux-gnu-  $(tool-archpref)-unknown-linux-gnu-)
+  endif
+endif
+
+ifdef CONFIG_FUNCTION_GRAPH_TRACER
+  ifndef KBUILD_MCOUNT_RA_ADDRESS
+    ifeq ($(call cc-option-yn,-mmcount-ra-address), y)
+      cflags-y += -mmcount-ra-address -DKBUILD_MCOUNT_RA_ADDRESS
+    endif
+  endif
+endif
+cflags-y += $(call cc-option, -mno-check-zero-division)
+
+ifdef CONFIG_32BIT
+ld-emul			= $(32bit-emul)
+vmlinux-32		= vmlinux
+vmlinux-64		= vmlinux.64
+
+cflags-y		+= -mabi=32
+endif
+
+ifdef CONFIG_64BIT
+ld-emul			= $(64bit-emul)
+vmlinux-32		= vmlinux.32
+vmlinux-64		= vmlinux
+
+cflags-y		+= -mabi=64
+endif
+
+all-$(CONFIG_BOOT_ELF32)	:= $(vmlinux-32)
+all-$(CONFIG_BOOT_ELF64)	:= $(vmlinux-64)
+all-$(CONFIG_SYS_SUPPORTS_ZBOOT)+= vmlinuz
+
+#
+# GCC uses -G 0 -mabicalls -fpic as default.  We don't want PIC in the kernel
+# code since it only slows down the whole thing.  At some point we might make
+# use of global pointer optimizations but their use of $28 conflicts with
+# the current pointer optimization.
+#
+# The DECStation requires an ECOFF kernel for remote booting, other MIPS
+# machines may also.  Since BFD is incredibly buggy with respect to
+# crossformat linking we rely on the elf2ecoff tool for format conversion.
+#
+cflags-y			+= -G 0 -mno-abicalls -fno-pic -pipe
+cflags-y			+= -msoft-float
+LDFLAGS_vmlinux			+= -G 0 -static -n -nostdlib
+KBUILD_AFLAGS_MODULE		+= -mlong-calls
+KBUILD_CFLAGS_MODULE		+= -mlong-calls
+
+ifeq ($(CONFIG_RELOCATABLE),y)
+LDFLAGS_vmlinux			+= --emit-relocs
+endif
+
+#
+# pass -msoft-float to GAS if it supports it.  However on newer binutils
+# (specifically newer than 2.24.51.20140728) we then also need to explicitly
+# set ".set hardfloat" in all files which manipulate floating point registers.
+#
+ifneq ($(call cc-option,$(cflags-y) -Wa$(comma)-msoft-float,),)
+	cflags-y		+= -DGAS_HAS_SET_HARDFLOAT -Wa,-msoft-float
+endif
+
+cflags-y += -ffreestanding
+
+cflags-$(CONFIG_CPU_BIG_ENDIAN)		+= -EB
+cflags-$(CONFIG_CPU_LITTLE_ENDIAN)	+= -EL
+
+cflags-$(CONFIG_SB1XXX_CORELIS)	+= $(call cc-option,-mno-sched-prolog) \
+				   -fno-omit-frame-pointer
+
+# Some distribution-specific toolchains might pass the -fstack-check
+# option during the build, which adds a simple stack-probe at the beginning
+# of every function.  This stack probe is to ensure that there is enough
+# stack space, else a SEGV is generated.  This is not desirable for MIPS
+# as kernel stacks are small, placed in unmapped virtual memory, and do not
+# grow when overflowed.  Especially on SGI IP27 platforms, this check will
+# lead to a NULL pointer dereference in _raw_spin_lock_irq.
+#
+# In disassembly, this stack probe appears at the top of a function as:
+#    sd		zero,<offset>(sp)
+# Where <offset> is a negative value.
+#
+cflags-y += -fno-stack-check
+
+# binutils from v2.35 when built with --enable-mips-fix-loongson3-llsc=yes,
+# supports an -mfix-loongson3-llsc flag which emits a sync prior to each ll
+# instruction to work around a CPU bug (see __SYNC_loongson3_war in asm/sync.h
+# for a description).
+#
+# We disable this in order to prevent the assembler meddling with the
+# instruction that labels refer to, ie. if we label an ll instruction:
+#
+# 1: ll v0, 0(a0)
+#
+# ...then with the assembler fix applied the label may actually point at a sync
+# instruction inserted by the assembler, and if we were using the label in an
+# exception table the table would no longer contain the address of the ll
+# instruction.
+#
+# Avoid this by explicitly disabling that assembler behaviour.
+#
+cflags-y += $(call cc-option,-Wa$(comma)-mno-fix-loongson3-llsc,)
+
+#
+# CPU-dependent compiler/assembler options for optimization.
+#
+cflags-$(CONFIG_CPU_R3000)	+= -march=r3000
+cflags-$(CONFIG_CPU_R4300)	+= -march=r4300 -Wa,--trap
+cflags-$(CONFIG_CPU_R4X00)	+= -march=r4600 -Wa,--trap
+cflags-$(CONFIG_CPU_TX49XX)	+= -march=r4600 -Wa,--trap
+cflags-$(CONFIG_CPU_MIPS32_R1)	+= -march=mips32 -Wa,--trap
+cflags-$(CONFIG_CPU_MIPS32_R2)	+= -march=mips32r2 -Wa,--trap
+cflags-$(CONFIG_CPU_MIPS32_R5)	+= -march=mips32r5 -Wa,--trap -modd-spreg
+cflags-$(CONFIG_CPU_MIPS32_R6)	+= -march=mips32r6 -Wa,--trap -modd-spreg
+cflags-$(CONFIG_CPU_MIPS64_R1)	+= -march=mips64 -Wa,--trap
+cflags-$(CONFIG_CPU_MIPS64_R2)	+= -march=mips64r2 -Wa,--trap
+cflags-$(CONFIG_CPU_MIPS64_R5)	+= -march=mips64r5 -Wa,--trap
+cflags-$(CONFIG_CPU_MIPS64_R6)	+= -march=mips64r6 -Wa,--trap
+cflags-$(CONFIG_CPU_P5600)	+= -march=p5600 -Wa,--trap -modd-spreg
+cflags-$(CONFIG_CPU_R5000)	+= -march=r5000 -Wa,--trap
+cflags-$(CONFIG_CPU_R5500)	+= $(call cc-option,-march=r5500,-march=r5000) \
+			-Wa,--trap
+cflags-$(CONFIG_CPU_NEVADA)	+= $(call cc-option,-march=rm5200,-march=r5000) \
+			-Wa,--trap
+cflags-$(CONFIG_CPU_RM7000)	+= $(call cc-option,-march=rm7000,-march=r5000) \
+			-Wa,--trap
+cflags-$(CONFIG_CPU_SB1)	+= $(call cc-option,-march=sb1,-march=r5000) \
+			-Wa,--trap
+cflags-$(CONFIG_CPU_SB1)	+= $(call cc-option,-mno-mdmx)
+cflags-$(CONFIG_CPU_SB1)	+= $(call cc-option,-mno-mips3d)
+cflags-$(CONFIG_CPU_R10000)	+= $(call cc-option,-march=r10000,-march=r8000) \
+			-Wa,--trap
+cflags-$(CONFIG_CPU_CAVIUM_OCTEON) += $(call cc-option,-march=octeon) -Wa,--trap
+ifeq (,$(findstring march=octeon, $(cflags-$(CONFIG_CPU_CAVIUM_OCTEON))))
+cflags-$(CONFIG_CPU_CAVIUM_OCTEON) += -Wa,-march=octeon
+endif
+cflags-$(CONFIG_CAVIUM_CN63XXP1) += -Wa,-mfix-cn63xxp1
+cflags-$(CONFIG_CPU_BMIPS)	+= -march=mips32 -Wa,-mips32 -Wa,--trap
+
+cflags-$(CONFIG_CPU_LOONGSON2E) += $(call cc-option,-march=loongson2e) -Wa,--trap
+cflags-$(CONFIG_CPU_LOONGSON2F) += $(call cc-option,-march=loongson2f) -Wa,--trap
+cflags-$(CONFIG_CPU_LOONGSON64) += $(call cc-option,-march=loongson3a,-march=mips64r2) -Wa,--trap
+# Some -march= flags enable MMI instructions, and GCC complains about that
+# support being enabled alongside -msoft-float. Thus explicitly disable MMI.
+cflags-$(CONFIG_CPU_LOONGSON2EF) += $(call cc-option,-mno-loongson-mmi)
+cflags-$(CONFIG_CPU_LOONGSON64) += $(call cc-option,-mno-loongson-mmi)
+
+cflags-$(CONFIG_CPU_R4000_WORKAROUNDS)	+= $(call cc-option,-mfix-r4000,)
+cflags-$(CONFIG_CPU_R4400_WORKAROUNDS)	+= $(call cc-option,-mfix-r4400,)
+cflags-$(CONFIG_CPU_DADDI_WORKAROUNDS)	+= $(call cc-option,-mno-daddi,)
+ifdef CONFIG_CPU_LOONGSON2F_WORKAROUNDS
+cflags-$(CONFIG_CPU_NOP_WORKAROUNDS) += -Wa,-mfix-loongson2f-nop
+cflags-$(CONFIG_CPU_JUMP_WORKAROUNDS) += -Wa,-mfix-loongson2f-jump
+endif
+
+#
+# Some versions of binutils, not currently mainline as of 2019/02/04, support
+# an -mfix-loongson3-llsc flag which emits a sync prior to each ll instruction
+# to work around a CPU bug (see __SYNC_loongson3_war in asm/sync.h for a
+# description).
+#
+# We disable this in order to prevent the assembler meddling with the
+# instruction that labels refer to, ie. if we label an ll instruction:
+#
+# 1: ll v0, 0(a0)
+#
+# ...then with the assembler fix applied the label may actually point at a sync
+# instruction inserted by the assembler, and if we were using the label in an
+# exception table the table would no longer contain the address of the ll
+# instruction.
+#
+# Avoid this by explicitly disabling that assembler behaviour. If upstream
+# binutils does not merge support for the flag then we can revisit & remove
+# this later - for now it ensures vendor toolchains don't cause problems.
+#
+cflags-$(CONFIG_CPU_LOONGSON64)	+= $(call as-option,-Wa$(comma)-mno-fix-loongson3-llsc,)
+
+# For smartmips configurations, there are hundreds of warnings due to ISA overrides
+# in assembly and header files. smartmips is only supported for MIPS32r1 onwards
+# and there is no support for 64-bit. Various '.set mips2' or '.set mips3' or
+# similar directives in the kernel will spam the build logs with the following warnings:
+# Warning: the `smartmips' extension requires MIPS32 revision 1 or greater
+# or
+# Warning: the 64-bit MIPS architecture does not support the `smartmips' extension
+# Pass -Wa,--no-warn to disable all assembler warnings until the kernel code has
+# been fixed properly.
+mips-cflags				:= $(cflags-y)
+ifeq ($(CONFIG_CPU_HAS_SMARTMIPS),y)
+smartmips-ase				:= $(call cc-option-yn,$(mips-cflags) -msmartmips)
+cflags-$(smartmips-ase)			+= -msmartmips -Wa,--no-warn
+endif
+ifeq ($(CONFIG_CPU_MICROMIPS),y)
+micromips-ase				:= $(call cc-option-yn,$(mips-cflags) -mmicromips)
+cflags-$(micromips-ase)			+= -mmicromips
+endif
+ifeq ($(CONFIG_CPU_HAS_MSA),y)
+toolchain-msa				:= $(call cc-option-yn,$(mips-cflags) -mhard-float -mfp64 -Wa$(comma)-mmsa)
+cflags-$(toolchain-msa)			+= -DTOOLCHAIN_SUPPORTS_MSA
+endif
+toolchain-virt				:= $(call cc-option-yn,$(mips-cflags) -mvirt)
+cflags-$(toolchain-virt)		+= -DTOOLCHAIN_SUPPORTS_VIRT
+# For -mmicromips, use -Wa,-fatal-warnings to catch unsupported -mxpa which
+# only warns
+xpa-cflags-y				:= $(mips-cflags)
+xpa-cflags-$(micromips-ase)		+= -mmicromips -Wa$(comma)-fatal-warnings
+toolchain-xpa				:= $(call cc-option-yn,$(xpa-cflags-y) -mxpa)
+cflags-$(toolchain-xpa)			+= -DTOOLCHAIN_SUPPORTS_XPA
+toolchain-crc				:= $(call cc-option-yn,$(mips-cflags) -Wa$(comma)-mcrc)
+cflags-$(toolchain-crc)			+= -DTOOLCHAIN_SUPPORTS_CRC
+toolchain-dsp				:= $(call cc-option-yn,$(mips-cflags) -Wa$(comma)-mdsp)
+cflags-$(toolchain-dsp)			+= -DTOOLCHAIN_SUPPORTS_DSP
+toolchain-ginv				:= $(call cc-option-yn,$(mips-cflags) -Wa$(comma)-mginv)
+cflags-$(toolchain-ginv)		+= -DTOOLCHAIN_SUPPORTS_GINV
+
+#
+# Firmware support
+#
+libs-$(CONFIG_FW_ARC)		+= arch/mips/fw/arc/
+libs-$(CONFIG_FW_CFE)		+= arch/mips/fw/cfe/
+libs-$(CONFIG_FW_SNIPROM)	+= arch/mips/fw/sni/
+libs-y				+= arch/mips/fw/lib/
+
+#
+# Kernel compression
+#
+ifdef CONFIG_SYS_SUPPORTS_ZBOOT
+COMPRESSION_FNAME		= vmlinuz
+else
+COMPRESSION_FNAME		= vmlinux
+endif
+
+#
+# Board-dependent options and extra files
+#
+include $(srctree)/arch/mips/Kbuild.platforms
+
+ifdef CONFIG_PHYSICAL_START
+load-y					= $(CONFIG_PHYSICAL_START)
+endif
+
+entry-y				= $(shell $(objtree)/arch/mips/tools/elf-entry vmlinux)
+cflags-y			+= -I$(srctree)/arch/mips/include/asm/mach-generic
+drivers-$(CONFIG_PCI)		+= arch/mips/pci/
+
+#
+# Automatically detect the build format. By default we choose
+# the elf format according to the load address.
+# We can always force a build with a 64-bits symbol format by
+# passing 'KBUILD_SYM32=no' option to the make's command line.
+#
+ifdef CONFIG_64BIT
+  ifndef KBUILD_SYM32
+    ifeq ($(shell expr $(load-y) \< 0xffffffff80000000), 0)
+      KBUILD_SYM32 = y
+    endif
+  endif
+
+  ifeq ($(KBUILD_SYM32), y)
+    cflags-$(KBUILD_SYM32) += -msym32 -DKBUILD_64BIT_SYM32
+  else
+    ifeq ($(CONFIG_CPU_DADDI_WORKAROUNDS), y)
+      $(error CONFIG_CPU_DADDI_WORKAROUNDS unsupported without -msym32)
+    endif
+  endif
+endif
+
+# When linking a 32-bit executable the LLVM linker cannot cope with a
+# 32-bit load address that has been sign-extended to 64 bits.  Simply
+# remove the upper 32 bits then, as it is safe to do so with other
+# linkers.
+ifdef CONFIG_64BIT
+	load-ld			= $(load-y)
+else
+	load-ld			= $(subst 0xffffffff,0x,$(load-y))
+endif
+
+KBUILD_AFLAGS	+= $(cflags-y)
+KBUILD_CFLAGS	+= $(cflags-y)
+KBUILD_CPPFLAGS += -DVMLINUX_LOAD_ADDRESS=$(load-y) -DLINKER_LOAD_ADDRESS=$(load-ld)
+KBUILD_CPPFLAGS += -DDATAOFFSET=$(if $(dataoffset-y),$(dataoffset-y),0)
+
+bootvars-y	= VMLINUX_LOAD_ADDRESS=$(load-y) \
+		  LINKER_LOAD_ADDRESS=$(load-ld) \
+		  VMLINUX_ENTRY_ADDRESS=$(entry-y) \
+		  PLATFORM="$(platform-y)" \
+		  ITS_INPUTS="$(its-y)"
+ifdef CONFIG_32BIT
+bootvars-y	+= ADDR_BITS=32
+endif
+ifdef CONFIG_64BIT
+bootvars-y	+= ADDR_BITS=64
+endif
+
+# This is required to get dwarf unwinding tables into .debug_frame
+# instead of .eh_frame so we don't discard them.
+KBUILD_CFLAGS += -fno-asynchronous-unwind-tables
+
+KBUILD_LDFLAGS		+= -m $(ld-emul)
+
+ifdef need-compiler
+CHECKFLAGS += $(shell $(CC) $(KBUILD_CFLAGS) -dM -E -x c /dev/null | \
+	grep -E -vw '__GNUC_(MINOR_|PATCHLEVEL_)?_' | \
+	sed -e "s/^\#define /-D'/" -e "s/ /'='/" -e "s/$$/'/" -e 's/\$$/&&/g')
+endif
+
+OBJCOPYFLAGS		+= --remove-section=.reginfo
+
+libs-y			+= arch/mips/lib/
+libs-$(CONFIG_MIPS_FP_SUPPORT) += arch/mips/math-emu/
+
+drivers-y			+= arch/mips/crypto/
+
+# suspend and hibernation support
+drivers-$(CONFIG_PM)	+= arch/mips/power/
+
+# boot image targets (arch/mips/boot/)
+boot-y			:= vmlinux.bin
+boot-y			+= vmlinux.ecoff
+boot-y			+= vmlinux.srec
+boot-y			+= uImage
+boot-y			+= uImage.bin
+boot-y			+= uImage.bz2
+boot-y			+= uImage.gz
+boot-y			+= uImage.lzma
+boot-y			+= uImage.lzo
+boot-y			+= vmlinux.itb
+boot-y			+= vmlinux.gz.itb
+boot-y			+= vmlinux.bz2.itb
+boot-y			+= vmlinux.lzma.itb
+boot-y			+= vmlinux.lzo.itb
+
+# compressed boot image targets (arch/mips/boot/compressed/)
+bootz-y			:= vmlinuz
+bootz-y			+= vmlinuz.bin
+bootz-y			+= vmlinuz.ecoff
+bootz-y			+= vmlinuz.srec
+bootz-y			+= uzImage.bin
+bootz-y			+= vmlinuz.itb
+
+#
+# Some machines like the Indy need 32-bit ELF binaries for booting purposes.
+# Other need ECOFF, so we build a 32-bit ELF binary for them which we then
+# convert to ECOFF using elf2ecoff.
+#
+quiet_cmd_32 = OBJCOPY $@
+	cmd_32 = $(OBJCOPY) -O $(32bit-bfd) $(OBJCOPYFLAGS) $< $@
+vmlinux.32: vmlinux
+	$(call cmd,32)
+
+#
+# The 64-bit ELF tools are pretty broken so at this time we generate 64-bit
+# ELF files from 32-bit files by conversion.
+#
+quiet_cmd_64 = OBJCOPY $@
+	cmd_64 = $(OBJCOPY) -O $(64bit-bfd) $(OBJCOPYFLAGS) $< $@
+vmlinux.64: vmlinux
+	$(call cmd,64)
+
+all:	$(all-y) $(KBUILD_DTBS)
+
+# boot
+$(boot-y): $(vmlinux-32) FORCE
+	$(Q)$(MAKE) $(build)=arch/mips/boot VMLINUX=$(vmlinux-32) \
+		$(bootvars-y) arch/mips/boot/$@
+
+ifdef CONFIG_SYS_SUPPORTS_ZBOOT
+# boot/compressed
+$(bootz-y): $(vmlinux-32) FORCE
+	$(Q)$(MAKE) $(build)=arch/mips/boot/compressed \
+		$(bootvars-y) 32bit-bfd=$(32bit-bfd) arch/mips/boot/$@
+else
+vmlinuz: FORCE
+	@echo '   CONFIG_SYS_SUPPORTS_ZBOOT is not enabled'
+	/bin/false
+endif
+
+
+CLEAN_FILES += vmlinux.32 vmlinux.64
+
+# device-trees
+core-y += arch/mips/boot/dts/
+
+archprepare:
+ifdef CONFIG_MIPS32_N32
+	@$(kecho) '  Checking missing-syscalls for N32'
+	$(Q)$(MAKE) $(build)=. missing-syscalls missing_syscalls_flags="-mabi=n32"
+endif
+ifdef CONFIG_MIPS32_O32
+	@$(kecho) '  Checking missing-syscalls for O32'
+	$(Q)$(MAKE) $(build)=. missing-syscalls missing_syscalls_flags="-mabi=32"
+endif
+
+install:
+	$(Q)install -D -m 755 vmlinux $(INSTALL_PATH)/vmlinux-$(KERNELRELEASE)
+ifdef CONFIG_SYS_SUPPORTS_ZBOOT
+	$(Q)install -D -m 755 vmlinuz $(INSTALL_PATH)/vmlinuz-$(KERNELRELEASE)
+endif
+	$(Q)install -D -m 644 .config $(INSTALL_PATH)/config-$(KERNELRELEASE)
+	$(Q)install -D -m 644 System.map $(INSTALL_PATH)/System.map-$(KERNELRELEASE)
+
+archheaders:
+	$(Q)$(MAKE) $(build)=arch/mips/kernel/syscalls all
+
+define archhelp
+	echo '  install              - install kernel into $(INSTALL_PATH)'
+	echo '  vmlinux.ecoff        - ECOFF boot image'
+	echo '  vmlinux.bin          - Raw binary boot image'
+	echo '  vmlinux.srec         - SREC boot image'
+	echo '  vmlinux.32           - 64-bit boot image wrapped in 32bits (IP22/IP32)'
+	echo '  vmlinuz              - Compressed boot(zboot) image'
+	echo '  vmlinuz.ecoff        - ECOFF zboot image'
+	echo '  vmlinuz.bin          - Raw binary zboot image'
+	echo '  vmlinuz.srec         - SREC zboot image'
+	echo '  uImage               - U-Boot image'
+	echo '  uImage.bin           - U-Boot image (uncompressed)'
+	echo '  uImage.bz2           - U-Boot image (bz2)'
+	echo '  uImage.gz            - U-Boot image (gzip)'
+	echo '  uImage.lzma          - U-Boot image (lzma)'
+	echo '  uImage.lzo           - U-Boot image (lzo)'
+	echo '  uzImage.bin          - U-Boot image (self-extracting)'
+	echo
+	echo '  These will be default as appropriate for a configured platform.'
+	echo
+	echo '  If you are targeting a system supported by generic kernels you may'
+	echo '  configure the kernel for a given architecture target like so:'
+	echo
+	echo '  {micro32,32,64}{r1,r2,r6}{el,}_defconfig <BOARDS="list of boards">'
+	echo
+	echo '  Where BOARDS is some subset of the following:'
+	for board in $(sort $(BOARDS)); do echo "    $${board}"; done
+	echo
+	echo '  Specifically the following generic default configurations are'
+	echo '  supported:'
+	echo
+	$(foreach cfg,$(generic_defconfigs),
+	  printf "  %-24s - Build generic kernel for $(call describe_generic_defconfig,$(cfg))\n" $(cfg);)
+	echo
+	echo '  The following legacy default configurations have been converted to'
+	echo '  generic and can still be used:'
+	echo
+	$(foreach cfg,$(sort $(legacy_defconfigs)),
+	  printf "  %-24s - Build $($(cfg)-y)\n" $(cfg);)
+	echo
+	echo '  Otherwise, the following default configurations are available:'
+endef
+
+generic_config_dir = $(srctree)/arch/$(ARCH)/configs/generic
+generic_defconfigs :=
+
+#
+# If the user generates a generic kernel configuration without specifying a
+# list of boards to include the config fragments for, default to including all
+# available board config fragments.
+#
+ifeq ($(BOARDS),)
+BOARDS = $(patsubst board-%.config,%,$(notdir $(wildcard $(generic_config_dir)/board-*.config)))
+endif
+
+#
+# Generic kernel configurations which merge generic_defconfig with the
+# appropriate config fragments from arch/mips/configs/generic/, resulting in
+# the ability to easily configure the kernel for a given architecture,
+# endianness & set of boards without duplicating the needed configuration in
+# hundreds of defconfig files.
+#
+define gen_generic_defconfigs
+$(foreach bits,$(1),$(foreach rev,$(2),$(foreach endian,$(3),
+target := $(bits)$(rev)$(filter el,$(endian))_defconfig
+generic_defconfigs += $$(target)
+$$(target): $(generic_config_dir)/$(bits)$(rev).config
+$$(target): $(generic_config_dir)/$(endian).config
+)))
+endef
+
+$(eval $(call gen_generic_defconfigs,32 64,r1 r2 r6,eb el))
+$(eval $(call gen_generic_defconfigs,micro32,r2,eb el))
+
+define describe_generic_defconfig
+$(subst 32r,MIPS32 r,$(subst 64r,MIPS64 r,$(subst el, little endian,$(patsubst %_defconfig,%,$(1)))))
+endef
+
+.PHONY: $(generic_defconfigs)
+$(generic_defconfigs):
+	$(Q)$(CONFIG_SHELL) $(srctree)/scripts/kconfig/merge_config.sh \
+		-m -O $(objtree) $(srctree)/arch/$(ARCH)/configs/generic_defconfig $^ | \
+		grep -Ev '^#'
+	$(Q)cp $(KCONFIG_CONFIG) $(objtree)/.config.$@
+	$(Q)$(MAKE) -f $(srctree)/Makefile olddefconfig \
+		KCONFIG_CONFIG=$(objtree)/.config.$@ >/dev/null
+	$(Q)$(CONFIG_SHELL) $(srctree)/arch/$(ARCH)/tools/generic-board-config.sh \
+		$(srctree) $(objtree) $(objtree)/.config.$@ $(KCONFIG_CONFIG) \
+		"$(origin BOARDS)" $(BOARDS)
+	$(Q)$(MAKE) -f $(srctree)/Makefile olddefconfig
+
+#
+# Prevent generic merge_config rules attempting to merge single fragments
+#
+$(generic_config_dir)/%.config: ;
+
+#
+# Prevent direct use of generic_defconfig, which is intended to be used as the
+# basis of the various ISA-specific targets generated above.
+#
+.PHONY: generic_defconfig
+generic_defconfig:
+	$(Q)echo "generic_defconfig is not intended for direct use, but should instead be"
+	$(Q)echo "used via an ISA-specific target from the following list:"
+	$(Q)echo
+	$(Q)for cfg in $(generic_defconfigs); do echo "  $${cfg}"; done
+	$(Q)echo
+	$(Q)false
+
+#
+# Legacy defconfig compatibility - these targets used to be real defconfigs but
+# now that the boards have been converted to use the generic kernel they are
+# wrappers around the generic rules above.
+#
+legacy_defconfigs		+= ocelot_defconfig
+ocelot_defconfig-y		:= 32r2el_defconfig BOARDS=ocelot
+
+legacy_defconfigs		+= sead3_defconfig
+sead3_defconfig-y		:= 32r2el_defconfig BOARDS=sead-3
+
+legacy_defconfigs		+= sead3micro_defconfig
+sead3micro_defconfig-y		:= micro32r2el_defconfig BOARDS=sead-3
+
+legacy_defconfigs		+= xilfpga_defconfig
+xilfpga_defconfig-y		:= 32r2el_defconfig BOARDS=xilfpga
+
+legacy_defconfigs		+= pistachio_defconfig
+pistachio_defconfig-y		:= 32r2el_defconfig BOARDS=marduk
+
+.PHONY: $(legacy_defconfigs)
+$(legacy_defconfigs):
+	$(Q)$(MAKE) -f $(srctree)/Makefile $($@-y)
diff --git a/arch/mips/Makefile.postlink b/arch/mips/Makefile.postlink
new file mode 100644
index 000000000..4b1d3ba3a
--- /dev/null
+++ b/arch/mips/Makefile.postlink
@@ -0,0 +1,44 @@
+# SPDX-License-Identifier: GPL-2.0
+# ===========================================================================
+# Post-link MIPS pass
+# ===========================================================================
+#
+# 1. Check that Loongson3 LL/SC workarounds are applied correctly
+# 2. Insert relocations into vmlinux
+
+PHONY := __archpost
+__archpost:
+
+-include include/config/auto.conf
+include scripts/Kbuild.include
+
+CMD_LS3_LLSC = arch/mips/tools/loongson3-llsc-check
+quiet_cmd_ls3_llsc = LLSCCHK $@
+      cmd_ls3_llsc = $(CMD_LS3_LLSC) $@
+
+CMD_RELOCS = arch/mips/boot/tools/relocs
+quiet_cmd_relocs = RELOCS  $@
+      cmd_relocs = $(CMD_RELOCS) $@
+
+# `@true` prevents complaint when there is nothing to be done
+
+vmlinux: FORCE
+	@true
+ifeq ($(CONFIG_CPU_LOONGSON3_WORKAROUNDS),y)
+	$(call if_changed,ls3_llsc)
+endif
+ifeq ($(CONFIG_RELOCATABLE),y)
+	$(call if_changed,relocs)
+endif
+
+%.ko: FORCE
+	@true
+
+clean:
+	@true
+
+PHONY += FORCE clean
+
+FORCE:
+
+.PHONY: $(PHONY)
diff --git a/arch/mips/alchemy/Kconfig b/arch/mips/alchemy/Kconfig
new file mode 100644
index 000000000..69734120a
--- /dev/null
+++ b/arch/mips/alchemy/Kconfig
@@ -0,0 +1,36 @@
+# SPDX-License-Identifier: GPL-2.0
+choice
+	prompt "Machine type"
+	depends on MIPS_ALCHEMY
+	default MIPS_DB1XXX
+
+config MIPS_MTX1
+	bool "4G Systems MTX-1 board"
+	select HAVE_PCI
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_HAS_EARLY_PRINTK
+
+config MIPS_DB1XXX
+	bool "Alchemy DB1XXX / PB1XXX boards"
+	select GPIOLIB
+	select HAVE_PCI
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_HAS_EARLY_PRINTK
+	help
+	  Select this option if you have one of the following Alchemy
+	  development boards:  DB1000 DB1500 DB1100 DB1550 DB1200 DB1300
+			       PB1500 PB1100 PB1550 PB1200
+	  Board type is autodetected during boot.
+
+config MIPS_XXS1500
+	bool "MyCable XXS1500 board"
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_HAS_EARLY_PRINTK
+
+config MIPS_GPR
+	bool "Trapeze ITS GPR board"
+	select HAVE_PCI
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_HAS_EARLY_PRINTK
+
+endchoice
diff --git a/arch/mips/alchemy/Makefile b/arch/mips/alchemy/Makefile
new file mode 100644
index 000000000..fabbc7019
--- /dev/null
+++ b/arch/mips/alchemy/Makefile
@@ -0,0 +1,4 @@
+# SPDX-License-Identifier: GPL-2.0-only
+obj-$(CONFIG_MIPS_GPR) += board-gpr.o
+obj-$(CONFIG_MIPS_MTX1) += board-mtx1.o
+obj-$(CONFIG_MIPS_XXS1500) += board-xxs1500.o
diff --git a/arch/mips/alchemy/Platform b/arch/mips/alchemy/Platform
new file mode 100644
index 000000000..c8cff50b0
--- /dev/null
+++ b/arch/mips/alchemy/Platform
@@ -0,0 +1,35 @@
+#
+# Core Alchemy code
+#
+platform-$(CONFIG_MIPS_ALCHEMY) += alchemy/common/
+
+
+#
+# AMD Alchemy Db1000/Db1500/Pb1500/Db1100/Pb1100
+#             Db1550/Pb1550/Db1200/Pb1200/Db1300
+#
+platform-$(CONFIG_MIPS_DB1XXX)	+= alchemy/devboards/
+cflags-$(CONFIG_MIPS_DB1XXX)	+= -I$(srctree)/arch/mips/include/asm/mach-db1x00
+load-$(CONFIG_MIPS_DB1XXX)	+= 0xffffffff80100000
+
+#
+# 4G-Systems MTX-1 "MeshCube" wireless router
+#
+load-$(CONFIG_MIPS_MTX1)	+= 0xffffffff80100000
+
+#
+# MyCable eval board
+#
+load-$(CONFIG_MIPS_XXS1500)	+= 0xffffffff80100000
+
+#
+# Trapeze ITS GRP board
+#
+load-$(CONFIG_MIPS_GPR)		+= 0xffffffff80100000
+
+# boards can specify their own <gpio.h> in one of their include dirs.
+# If they do, placing this line here at the end will make sure the
+# compiler picks the board one.	 If they don't, it will make sure
+# the alchemy generic gpio header is picked up.
+
+cflags-$(CONFIG_MIPS_ALCHEMY)	+= -I$(srctree)/arch/mips/include/asm/mach-au1x00
diff --git a/arch/mips/alchemy/board-gpr.c b/arch/mips/alchemy/board-gpr.c
new file mode 100644
index 000000000..f587c40b6
--- /dev/null
+++ b/arch/mips/alchemy/board-gpr.c
@@ -0,0 +1,292 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * GPR board platform device registration (Au1550)
+ *
+ * Copyright (C) 2010 Wolfgang Grandegger <wg@denx.de>
+ */
+
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+#include <linux/leds.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/platform_data/i2c-gpio.h>
+#include <linux/gpio/machine.h>
+#include <asm/bootinfo.h>
+#include <asm/idle.h>
+#include <asm/reboot.h>
+#include <asm/setup.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/gpio-au1000.h>
+#include <prom.h>
+
+const char *get_system_type(void)
+{
+	return "GPR";
+}
+
+void prom_putchar(char c)
+{
+	alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
+}
+
+static void gpr_reset(char *c)
+{
+	/* switch System-LED to orange (red# and green# on) */
+	alchemy_gpio_direction_output(4, 0);
+	alchemy_gpio_direction_output(5, 0);
+
+	/* trigger watchdog to reset board in 200ms */
+	printk(KERN_EMERG "Triggering watchdog soft reset...\n");
+	raw_local_irq_disable();
+	alchemy_gpio_direction_output(1, 0);
+	udelay(1);
+	alchemy_gpio_set_value(1, 1);
+	while (1)
+		cpu_wait();
+}
+
+static void gpr_power_off(void)
+{
+	while (1)
+		cpu_wait();
+}
+
+void __init board_setup(void)
+{
+	printk(KERN_INFO "Trapeze ITS GPR board\n");
+
+	pm_power_off = gpr_power_off;
+	_machine_halt = gpr_power_off;
+	_machine_restart = gpr_reset;
+
+	/* Enable UART1/3 */
+	alchemy_uart_enable(AU1000_UART3_PHYS_ADDR);
+	alchemy_uart_enable(AU1000_UART1_PHYS_ADDR);
+
+	/* Take away Reset of UMTS-card */
+	alchemy_gpio_direction_output(215, 1);
+}
+
+/*
+ * Watchdog
+ */
+static struct resource gpr_wdt_resource[] = {
+	[0] = {
+		.start	= 1,
+		.end	= 1,
+		.name	= "gpr-adm6320-wdt",
+		.flags	= IORESOURCE_IRQ,
+	}
+};
+
+static struct platform_device gpr_wdt_device = {
+	.name = "adm6320-wdt",
+	.id = 0,
+	.num_resources = ARRAY_SIZE(gpr_wdt_resource),
+	.resource = gpr_wdt_resource,
+};
+
+/*
+ * FLASH
+ *
+ * 0x00000000-0x00200000 : "kernel"
+ * 0x00200000-0x00a00000 : "rootfs"
+ * 0x01d00000-0x01f00000 : "config"
+ * 0x01c00000-0x01d00000 : "yamon"
+ * 0x01d00000-0x01d40000 : "yamon env vars"
+ * 0x00000000-0x00a00000 : "kernel+rootfs"
+ */
+static struct mtd_partition gpr_mtd_partitions[] = {
+	{
+		.name	= "kernel",
+		.size	= 0x00200000,
+		.offset = 0,
+	},
+	{
+		.name	= "rootfs",
+		.size	= 0x00800000,
+		.offset = MTDPART_OFS_APPEND,
+		.mask_flags = MTD_WRITEABLE,
+	},
+	{
+		.name	= "config",
+		.size	= 0x00200000,
+		.offset = 0x01d00000,
+	},
+	{
+		.name	= "yamon",
+		.size	= 0x00100000,
+		.offset = 0x01c00000,
+	},
+	{
+		.name	= "yamon env vars",
+		.size	= 0x00040000,
+		.offset = MTDPART_OFS_APPEND,
+	},
+	{
+		.name	= "kernel+rootfs",
+		.size	= 0x00a00000,
+		.offset = 0,
+	},
+};
+
+static struct physmap_flash_data gpr_flash_data = {
+	.width		= 4,
+	.nr_parts	= ARRAY_SIZE(gpr_mtd_partitions),
+	.parts		= gpr_mtd_partitions,
+};
+
+static struct resource gpr_mtd_resource = {
+	.start	= 0x1e000000,
+	.end	= 0x1fffffff,
+	.flags	= IORESOURCE_MEM,
+};
+
+static struct platform_device gpr_mtd_device = {
+	.name		= "physmap-flash",
+	.dev		= {
+		.platform_data	= &gpr_flash_data,
+	},
+	.num_resources	= 1,
+	.resource	= &gpr_mtd_resource,
+};
+
+/*
+ * LEDs
+ */
+static const struct gpio_led gpr_gpio_leds[] = {
+	{	/* green */
+		.name			= "gpr:green",
+		.gpio			= 4,
+		.active_low		= 1,
+	},
+	{	/* red */
+		.name			= "gpr:red",
+		.gpio			= 5,
+		.active_low		= 1,
+	}
+};
+
+static struct gpio_led_platform_data gpr_led_data = {
+	.num_leds = ARRAY_SIZE(gpr_gpio_leds),
+	.leds = gpr_gpio_leds,
+};
+
+static struct platform_device gpr_led_devices = {
+	.name = "leds-gpio",
+	.id = -1,
+	.dev = {
+		.platform_data = &gpr_led_data,
+	}
+};
+
+/*
+ * I2C
+ */
+static struct gpiod_lookup_table gpr_i2c_gpiod_table = {
+	.dev_id = "i2c-gpio",
+	.table = {
+		/*
+		 * This should be on "GPIO2" which has base at 200 so
+		 * the global numbers 209 and 210 should correspond to
+		 * local offsets 9 and 10.
+		 */
+		GPIO_LOOKUP_IDX("alchemy-gpio2", 9, NULL, 0,
+				GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("alchemy-gpio2", 10, NULL, 1,
+				GPIO_ACTIVE_HIGH),
+	},
+};
+
+static struct i2c_gpio_platform_data gpr_i2c_data = {
+	/*
+	 * The open drain mode is hardwired somewhere or an electrical
+	 * property of the alchemy GPIO controller.
+	 */
+	.sda_is_open_drain	= 1,
+	.scl_is_open_drain	= 1,
+	.udelay			= 2,		/* ~100 kHz */
+	.timeout		= HZ,
+};
+
+static struct platform_device gpr_i2c_device = {
+	.name			= "i2c-gpio",
+	.id			= -1,
+	.dev.platform_data	= &gpr_i2c_data,
+};
+
+static struct i2c_board_info gpr_i2c_info[] __initdata = {
+	{
+		I2C_BOARD_INFO("lm83", 0x18),
+	}
+};
+
+
+
+static struct resource alchemy_pci_host_res[] = {
+	[0] = {
+		.start	= AU1500_PCI_PHYS_ADDR,
+		.end	= AU1500_PCI_PHYS_ADDR + 0xfff,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+static int gpr_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
+{
+	if ((slot == 0) && (pin == 1))
+		return AU1550_PCI_INTA;
+	else if ((slot == 0) && (pin == 2))
+		return AU1550_PCI_INTB;
+
+	return 0xff;
+}
+
+static struct alchemy_pci_platdata gpr_pci_pd = {
+	.board_map_irq	= gpr_map_pci_irq,
+	.pci_cfg_set	= PCI_CONFIG_AEN | PCI_CONFIG_R2H | PCI_CONFIG_R1H |
+			  PCI_CONFIG_CH |
+#if defined(__MIPSEB__)
+			  PCI_CONFIG_SIC_HWA_DAT | PCI_CONFIG_SM,
+#else
+			  0,
+#endif
+};
+
+static struct platform_device gpr_pci_host_dev = {
+	.dev.platform_data = &gpr_pci_pd,
+	.name		= "alchemy-pci",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(alchemy_pci_host_res),
+	.resource	= alchemy_pci_host_res,
+};
+
+static struct platform_device *gpr_devices[] __initdata = {
+	&gpr_wdt_device,
+	&gpr_mtd_device,
+	&gpr_i2c_device,
+	&gpr_led_devices,
+};
+
+static int __init gpr_pci_init(void)
+{
+	return platform_device_register(&gpr_pci_host_dev);
+}
+/* must be arch_initcall; MIPS PCI scans busses in a subsys_initcall */
+arch_initcall(gpr_pci_init);
+
+
+static int __init gpr_dev_init(void)
+{
+	gpiod_add_lookup_table(&gpr_i2c_gpiod_table);
+	i2c_register_board_info(0, gpr_i2c_info, ARRAY_SIZE(gpr_i2c_info));
+
+	return platform_add_devices(gpr_devices, ARRAY_SIZE(gpr_devices));
+}
+device_initcall(gpr_dev_init);
diff --git a/arch/mips/alchemy/board-mtx1.c b/arch/mips/alchemy/board-mtx1.c
new file mode 100644
index 000000000..68ea57511
--- /dev/null
+++ b/arch/mips/alchemy/board-mtx1.c
@@ -0,0 +1,285 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * MTX-1 platform devices registration (Au1500)
+ *
+ * Copyright (C) 2007-2009, Florian Fainelli <florian@openwrt.org>
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/leds.h>
+#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
+#include <linux/gpio_keys.h>
+#include <linux/input.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+#include <mtd/mtd-abi.h>
+#include <asm/bootinfo.h>
+#include <asm/reboot.h>
+#include <asm/setup.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/gpio-au1000.h>
+#include <asm/mach-au1x00/au1xxx_eth.h>
+#include <prom.h>
+
+const char *get_system_type(void)
+{
+	return "MTX-1";
+}
+
+void prom_putchar(char c)
+{
+	alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
+}
+
+static void mtx1_reset(char *c)
+{
+	/* Jump to the reset vector */
+	__asm__ __volatile__("jr\t%0" : : "r"(0xbfc00000));
+}
+
+static void mtx1_power_off(void)
+{
+	while (1)
+		asm volatile (
+		"	.set	mips32					\n"
+		"	wait						\n"
+		"	.set	mips0					\n");
+}
+
+void __init board_setup(void)
+{
+#if IS_ENABLED(CONFIG_USB_OHCI_HCD)
+	/* Enable USB power switch */
+	alchemy_gpio_direction_output(204, 0);
+#endif /* IS_ENABLED(CONFIG_USB_OHCI_HCD) */
+
+	/* Initialize sys_pinfunc */
+	alchemy_wrsys(SYS_PF_NI2, AU1000_SYS_PINFUNC);
+
+	/* Initialize GPIO */
+	alchemy_wrsys(~0, AU1000_SYS_TRIOUTCLR);
+	alchemy_gpio_direction_output(0, 0);	/* Disable M66EN (PCI 66MHz) */
+	alchemy_gpio_direction_output(3, 1);	/* Disable PCI CLKRUN# */
+	alchemy_gpio_direction_output(1, 1);	/* Enable EXT_IO3 */
+	alchemy_gpio_direction_output(5, 0);	/* Disable eth PHY TX_ER */
+
+	/* Enable LED and set it to green */
+	alchemy_gpio_direction_output(211, 1);	/* green on */
+	alchemy_gpio_direction_output(212, 0);	/* red off */
+
+	pm_power_off = mtx1_power_off;
+	_machine_halt = mtx1_power_off;
+	_machine_restart = mtx1_reset;
+
+	printk(KERN_INFO "4G Systems MTX-1 Board\n");
+}
+
+/******************************************************************************/
+
+static struct gpio_keys_button mtx1_gpio_button[] = {
+	{
+		.gpio = 207,
+		.code = BTN_0,
+		.desc = "System button",
+	}
+};
+
+static struct gpio_keys_platform_data mtx1_buttons_data = {
+	.buttons = mtx1_gpio_button,
+	.nbuttons = ARRAY_SIZE(mtx1_gpio_button),
+};
+
+static struct platform_device mtx1_button = {
+	.name = "gpio-keys",
+	.id = -1,
+	.dev = {
+		.platform_data = &mtx1_buttons_data,
+	}
+};
+
+static struct gpiod_lookup_table mtx1_wdt_gpio_table = {
+	.dev_id = "mtx1-wdt.0",
+	.table = {
+		/* Global number 215 is offset 15 on Alchemy GPIO 2 */
+		GPIO_LOOKUP("alchemy-gpio2", 15, NULL, GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
+static struct platform_device mtx1_wdt = {
+	.name = "mtx1-wdt",
+	.id = 0,
+};
+
+static const struct gpio_led default_leds[] = {
+	{
+		.name	= "mtx1:green",
+		.gpio = 211,
+	}, {
+		.name = "mtx1:red",
+		.gpio = 212,
+	},
+};
+
+static struct gpio_led_platform_data mtx1_led_data = {
+	.num_leds = ARRAY_SIZE(default_leds),
+	.leds = default_leds,
+};
+
+static struct platform_device mtx1_gpio_leds = {
+	.name = "leds-gpio",
+	.id = -1,
+	.dev = {
+		.platform_data = &mtx1_led_data,
+	}
+};
+
+static struct mtd_partition mtx1_mtd_partitions[] = {
+	{
+		.name	= "filesystem",
+		.size	= 0x01C00000,
+		.offset = 0,
+	},
+	{
+		.name	= "yamon",
+		.size	= 0x00100000,
+		.offset = MTDPART_OFS_APPEND,
+		.mask_flags = MTD_WRITEABLE,
+	},
+	{
+		.name	= "kernel",
+		.size	= 0x002c0000,
+		.offset = MTDPART_OFS_APPEND,
+	},
+	{
+		.name	= "yamon env",
+		.size	= 0x00040000,
+		.offset = MTDPART_OFS_APPEND,
+	},
+};
+
+static struct physmap_flash_data mtx1_flash_data = {
+	.width		= 4,
+	.nr_parts	= 4,
+	.parts		= mtx1_mtd_partitions,
+};
+
+static struct resource mtx1_mtd_resource = {
+	.start	= 0x1e000000,
+	.end	= 0x1fffffff,
+	.flags	= IORESOURCE_MEM,
+};
+
+static struct platform_device mtx1_mtd = {
+	.name		= "physmap-flash",
+	.dev		= {
+		.platform_data	= &mtx1_flash_data,
+	},
+	.num_resources	= 1,
+	.resource	= &mtx1_mtd_resource,
+};
+
+static struct resource alchemy_pci_host_res[] = {
+	[0] = {
+		.start	= AU1500_PCI_PHYS_ADDR,
+		.end	= AU1500_PCI_PHYS_ADDR + 0xfff,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+static int mtx1_pci_idsel(unsigned int devsel, int assert)
+{
+	/* This function is only necessary to support a proprietary Cardbus
+	 * adapter on the mtx-1 "singleboard" variant. It triggers a custom
+	 * logic chip connected to EXT_IO3 (GPIO1) to suppress IDSEL signals.
+	 */
+	udelay(1);
+
+	if (assert && devsel != 0)
+		/* Suppress signal to Cardbus */
+		alchemy_gpio_set_value(1, 0);	/* set EXT_IO3 OFF */
+	else
+		alchemy_gpio_set_value(1, 1);	/* set EXT_IO3 ON */
+
+	udelay(1);
+	return 1;
+}
+
+static const char mtx1_irqtab[][5] = {
+	[0] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTA, 0xff, 0xff }, /* IDSEL 00 - AdapterA-Slot0 (top) */
+	[1] = { -1, AU1500_PCI_INTB, AU1500_PCI_INTA, 0xff, 0xff }, /* IDSEL 01 - AdapterA-Slot1 (bottom) */
+	[2] = { -1, AU1500_PCI_INTC, AU1500_PCI_INTD, 0xff, 0xff }, /* IDSEL 02 - AdapterB-Slot0 (top) */
+	[3] = { -1, AU1500_PCI_INTD, AU1500_PCI_INTC, 0xff, 0xff }, /* IDSEL 03 - AdapterB-Slot1 (bottom) */
+	[4] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, 0xff, 0xff }, /* IDSEL 04 - AdapterC-Slot0 (top) */
+	[5] = { -1, AU1500_PCI_INTB, AU1500_PCI_INTA, 0xff, 0xff }, /* IDSEL 05 - AdapterC-Slot1 (bottom) */
+	[6] = { -1, AU1500_PCI_INTC, AU1500_PCI_INTD, 0xff, 0xff }, /* IDSEL 06 - AdapterD-Slot0 (top) */
+	[7] = { -1, AU1500_PCI_INTD, AU1500_PCI_INTC, 0xff, 0xff }, /* IDSEL 07 - AdapterD-Slot1 (bottom) */
+};
+
+static int mtx1_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
+{
+	return mtx1_irqtab[slot][pin];
+}
+
+static struct alchemy_pci_platdata mtx1_pci_pd = {
+	.board_map_irq	 = mtx1_map_pci_irq,
+	.board_pci_idsel = mtx1_pci_idsel,
+	.pci_cfg_set	 = PCI_CONFIG_AEN | PCI_CONFIG_R2H | PCI_CONFIG_R1H |
+			   PCI_CONFIG_CH |
+#if defined(__MIPSEB__)
+			   PCI_CONFIG_SIC_HWA_DAT | PCI_CONFIG_SM,
+#else
+			   0,
+#endif
+};
+
+static struct platform_device mtx1_pci_host = {
+	.dev.platform_data = &mtx1_pci_pd,
+	.name		= "alchemy-pci",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(alchemy_pci_host_res),
+	.resource	= alchemy_pci_host_res,
+};
+
+static struct platform_device *mtx1_devs[] __initdata = {
+	&mtx1_pci_host,
+	&mtx1_gpio_leds,
+	&mtx1_wdt,
+	&mtx1_button,
+	&mtx1_mtd,
+};
+
+static struct au1000_eth_platform_data mtx1_au1000_eth0_pdata = {
+	.phy_search_highest_addr	= 1,
+	.phy1_search_mac0		= 1,
+};
+
+static int __init mtx1_register_devices(void)
+{
+	int rc;
+
+	irq_set_irq_type(AU1500_GPIO204_INT, IRQ_TYPE_LEVEL_HIGH);
+	irq_set_irq_type(AU1500_GPIO201_INT, IRQ_TYPE_LEVEL_LOW);
+	irq_set_irq_type(AU1500_GPIO202_INT, IRQ_TYPE_LEVEL_LOW);
+	irq_set_irq_type(AU1500_GPIO203_INT, IRQ_TYPE_LEVEL_LOW);
+	irq_set_irq_type(AU1500_GPIO205_INT, IRQ_TYPE_LEVEL_LOW);
+
+	au1xxx_override_eth_cfg(0, &mtx1_au1000_eth0_pdata);
+
+	rc = gpio_request(mtx1_gpio_button[0].gpio,
+					mtx1_gpio_button[0].desc);
+	if (rc < 0) {
+		printk(KERN_INFO "mtx1: failed to request %d\n",
+					mtx1_gpio_button[0].gpio);
+		goto out;
+	}
+	gpio_direction_input(mtx1_gpio_button[0].gpio);
+out:
+	gpiod_add_lookup_table(&mtx1_wdt_gpio_table);
+	return platform_add_devices(mtx1_devs, ARRAY_SIZE(mtx1_devs));
+}
+arch_initcall(mtx1_register_devices);
diff --git a/arch/mips/alchemy/board-xxs1500.c b/arch/mips/alchemy/board-xxs1500.c
new file mode 100644
index 000000000..f175bce29
--- /dev/null
+++ b/arch/mips/alchemy/board-xxs1500.c
@@ -0,0 +1,125 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * BRIEF MODULE DESCRIPTION
+ *	MyCable XXS1500 board support
+ *
+ * Copyright 2003, 2008 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc. <source@mvista.com>
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+#include <linux/delay.h>
+#include <linux/pm.h>
+#include <asm/bootinfo.h>
+#include <asm/reboot.h>
+#include <asm/setup.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/gpio-au1000.h>
+#include <prom.h>
+
+const char *get_system_type(void)
+{
+	return "XXS1500";
+}
+
+void prom_putchar(char c)
+{
+	alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
+}
+
+static void xxs1500_reset(char *c)
+{
+	/* Jump to the reset vector */
+	__asm__ __volatile__("jr\t%0" : : "r"(0xbfc00000));
+}
+
+static void xxs1500_power_off(void)
+{
+	while (1)
+		asm volatile (
+		"	.set	mips32					\n"
+		"	wait						\n"
+		"	.set	mips0					\n");
+}
+
+void __init board_setup(void)
+{
+	u32 pin_func;
+
+	pm_power_off = xxs1500_power_off;
+	_machine_halt = xxs1500_power_off;
+	_machine_restart = xxs1500_reset;
+
+	alchemy_gpio1_input_enable();
+	alchemy_gpio2_enable();
+
+	/* Set multiple use pins (UART3/GPIO) to UART (it's used as UART too) */
+	pin_func  = alchemy_rdsys(AU1000_SYS_PINFUNC) & ~SYS_PF_UR3;
+	pin_func |= SYS_PF_UR3;
+	alchemy_wrsys(pin_func, AU1000_SYS_PINFUNC);
+
+	/* Enable UART */
+	alchemy_uart_enable(AU1000_UART3_PHYS_ADDR);
+	/* Enable DTR (MCR bit 0) = USB power up */
+	__raw_writel(1, (void __iomem *)KSEG1ADDR(AU1000_UART3_PHYS_ADDR + 0x18));
+	wmb();
+}
+
+/******************************************************************************/
+
+static struct resource xxs1500_pcmcia_res[] = {
+	{
+		.name	= "pcmcia-io",
+		.flags	= IORESOURCE_MEM,
+		.start	= AU1000_PCMCIA_IO_PHYS_ADDR,
+		.end	= AU1000_PCMCIA_IO_PHYS_ADDR + 0x000400000 - 1,
+	},
+	{
+		.name	= "pcmcia-attr",
+		.flags	= IORESOURCE_MEM,
+		.start	= AU1000_PCMCIA_ATTR_PHYS_ADDR,
+		.end	= AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+	},
+	{
+		.name	= "pcmcia-mem",
+		.flags	= IORESOURCE_MEM,
+		.start	= AU1000_PCMCIA_MEM_PHYS_ADDR,
+		.end	= AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+	},
+};
+
+static struct platform_device xxs1500_pcmcia_dev = {
+	.name		= "xxs1500_pcmcia",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(xxs1500_pcmcia_res),
+	.resource	= xxs1500_pcmcia_res,
+};
+
+static struct platform_device *xxs1500_devs[] __initdata = {
+	&xxs1500_pcmcia_dev,
+};
+
+static int __init xxs1500_dev_init(void)
+{
+	irq_set_irq_type(AU1500_GPIO204_INT, IRQ_TYPE_LEVEL_HIGH);
+	irq_set_irq_type(AU1500_GPIO201_INT, IRQ_TYPE_LEVEL_LOW);
+	irq_set_irq_type(AU1500_GPIO202_INT, IRQ_TYPE_LEVEL_LOW);
+	irq_set_irq_type(AU1500_GPIO203_INT, IRQ_TYPE_LEVEL_LOW);
+	irq_set_irq_type(AU1500_GPIO205_INT, IRQ_TYPE_LEVEL_LOW);
+	irq_set_irq_type(AU1500_GPIO207_INT, IRQ_TYPE_LEVEL_LOW);
+
+	irq_set_irq_type(AU1500_GPIO0_INT, IRQ_TYPE_LEVEL_LOW);
+	irq_set_irq_type(AU1500_GPIO1_INT, IRQ_TYPE_LEVEL_LOW);
+	irq_set_irq_type(AU1500_GPIO2_INT, IRQ_TYPE_LEVEL_LOW);
+	irq_set_irq_type(AU1500_GPIO3_INT, IRQ_TYPE_LEVEL_LOW);
+	irq_set_irq_type(AU1500_GPIO4_INT, IRQ_TYPE_LEVEL_LOW); /* CF irq */
+	irq_set_irq_type(AU1500_GPIO5_INT, IRQ_TYPE_LEVEL_LOW);
+
+	return platform_add_devices(xxs1500_devs,
+				    ARRAY_SIZE(xxs1500_devs));
+}
+device_initcall(xxs1500_dev_init);
diff --git a/arch/mips/alchemy/common/Makefile b/arch/mips/alchemy/common/Makefile
new file mode 100644
index 000000000..a0e94388d
--- /dev/null
+++ b/arch/mips/alchemy/common/Makefile
@@ -0,0 +1,10 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+#  Copyright 2000, 2008 MontaVista Software Inc.
+#  Author: MontaVista Software, Inc. <source@mvista.com>
+#
+# Makefile for the Alchemy Au1xx0 CPUs, generic files.
+#
+
+obj-y += prom.o time.o clock.o platform.o power.o gpiolib.o \
+	 setup.o sleeper.o dma.o dbdma.o vss.o irq.o usb.o
diff --git a/arch/mips/alchemy/common/clock.c b/arch/mips/alchemy/common/clock.c
new file mode 100644
index 000000000..c01be8c45
--- /dev/null
+++ b/arch/mips/alchemy/common/clock.c
@@ -0,0 +1,1116 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Alchemy clocks.
+ *
+ * Exposes all configurable internal clock sources to the clk framework.
+ *
+ * We have:
+ *  - Root source, usually 12MHz supplied by an external crystal
+ *  - 3 PLLs which generate multiples of root rate [AUX, CPU, AUX2]
+ *
+ * Dividers:
+ *  - 6 clock dividers with:
+ *   * selectable source [one of the PLLs],
+ *   * output divided between [2 .. 512 in steps of 2] (!Au1300)
+ *     or [1 .. 256 in steps of 1] (Au1300),
+ *   * can be enabled individually.
+ *
+ * - up to 6 "internal" (fixed) consumers which:
+ *   * take either AUXPLL or one of the above 6 dividers as input,
+ *   * divide this input by 1, 2, or 4 (and 3 on Au1300).
+ *   * can be disabled separately.
+ *
+ * Misc clocks:
+ * - sysbus clock: CPU core clock (CPUPLL) divided by 2, 3 or 4.
+ *    depends on board design and should be set by bootloader, read-only.
+ * - peripheral clock: half the rate of sysbus clock, source for a lot
+ *    of peripheral blocks, read-only.
+ * - memory clock: clk rate to main memory chips, depends on board
+ *    design and is read-only,
+ * - lrclk: the static bus clock signal for synchronous operation.
+ *    depends on board design, must be set by bootloader,
+ *    but may be required to correctly configure devices attached to
+ *    the static bus. The Au1000/1500/1100 manuals call it LCLK, on
+ *    later models it's called RCLK.
+ */
+
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/clkdev.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+#include <linux/types.h>
+#include <asm/mach-au1x00/au1000.h>
+
+/* Base clock: 12MHz is the default in all databooks, and I haven't
+ * found any board yet which uses a different rate.
+ */
+#define ALCHEMY_ROOTCLK_RATE	12000000
+
+/*
+ * the internal sources which can be driven by the PLLs and dividers.
+ * Names taken from the databooks, refer to them for more information,
+ * especially which ones are share a clock line.
+ */
+static const char * const alchemy_au1300_intclknames[] = {
+	"lcd_intclk", "gpemgp_clk", "maempe_clk", "maebsa_clk",
+	"EXTCLK0", "EXTCLK1"
+};
+
+static const char * const alchemy_au1200_intclknames[] = {
+	"lcd_intclk", NULL, NULL, NULL, "EXTCLK0", "EXTCLK1"
+};
+
+static const char * const alchemy_au1550_intclknames[] = {
+	"usb_clk", "psc0_intclk", "psc1_intclk", "pci_clko",
+	"EXTCLK0", "EXTCLK1"
+};
+
+static const char * const alchemy_au1100_intclknames[] = {
+	"usb_clk", "lcd_intclk", NULL, "i2s_clk", "EXTCLK0", "EXTCLK1"
+};
+
+static const char * const alchemy_au1500_intclknames[] = {
+	NULL, "usbd_clk", "usbh_clk", "pci_clko", "EXTCLK0", "EXTCLK1"
+};
+
+static const char * const alchemy_au1000_intclknames[] = {
+	"irda_clk", "usbd_clk", "usbh_clk", "i2s_clk", "EXTCLK0",
+	"EXTCLK1"
+};
+
+/* aliases for a few on-chip sources which are either shared
+ * or have gone through name changes.
+ */
+static struct clk_aliastable {
+	char *alias;
+	char *base;
+	int cputype;
+} alchemy_clk_aliases[] __initdata = {
+	{ "usbh_clk", "usb_clk",    ALCHEMY_CPU_AU1100 },
+	{ "usbd_clk", "usb_clk",    ALCHEMY_CPU_AU1100 },
+	{ "irda_clk", "usb_clk",    ALCHEMY_CPU_AU1100 },
+	{ "usbh_clk", "usb_clk",    ALCHEMY_CPU_AU1550 },
+	{ "usbd_clk", "usb_clk",    ALCHEMY_CPU_AU1550 },
+	{ "psc2_intclk", "usb_clk", ALCHEMY_CPU_AU1550 },
+	{ "psc3_intclk", "EXTCLK0", ALCHEMY_CPU_AU1550 },
+	{ "psc0_intclk", "EXTCLK0", ALCHEMY_CPU_AU1200 },
+	{ "psc1_intclk", "EXTCLK1", ALCHEMY_CPU_AU1200 },
+	{ "psc0_intclk", "EXTCLK0", ALCHEMY_CPU_AU1300 },
+	{ "psc2_intclk", "EXTCLK0", ALCHEMY_CPU_AU1300 },
+	{ "psc1_intclk", "EXTCLK1", ALCHEMY_CPU_AU1300 },
+	{ "psc3_intclk", "EXTCLK1", ALCHEMY_CPU_AU1300 },
+
+	{ NULL, NULL, 0 },
+};
+
+#define IOMEM(x)	((void __iomem *)(KSEG1ADDR(CPHYSADDR(x))))
+
+/* access locks to SYS_FREQCTRL0/1 and SYS_CLKSRC registers */
+static spinlock_t alchemy_clk_fg0_lock;
+static spinlock_t alchemy_clk_fg1_lock;
+static DEFINE_SPINLOCK(alchemy_clk_csrc_lock);
+
+/* CPU Core clock *****************************************************/
+
+static unsigned long alchemy_clk_cpu_recalc(struct clk_hw *hw,
+					    unsigned long parent_rate)
+{
+	unsigned long t;
+
+	/*
+	 * On early Au1000, sys_cpupll was write-only. Since these
+	 * silicon versions of Au1000 are not sold, we don't bend
+	 * over backwards trying to determine the frequency.
+	 */
+	if (unlikely(au1xxx_cpu_has_pll_wo()))
+		t = 396000000;
+	else {
+		t = alchemy_rdsys(AU1000_SYS_CPUPLL) & 0x7f;
+		if (alchemy_get_cputype() < ALCHEMY_CPU_AU1300)
+			t &= 0x3f;
+		t *= parent_rate;
+	}
+
+	return t;
+}
+
+void __init alchemy_set_lpj(void)
+{
+	preset_lpj = alchemy_clk_cpu_recalc(NULL, ALCHEMY_ROOTCLK_RATE);
+	preset_lpj /= 2 * HZ;
+}
+
+static const struct clk_ops alchemy_clkops_cpu = {
+	.recalc_rate	= alchemy_clk_cpu_recalc,
+};
+
+static struct clk __init *alchemy_clk_setup_cpu(const char *parent_name,
+						int ctype)
+{
+	struct clk_init_data id;
+	struct clk_hw *h;
+	struct clk *clk;
+
+	h = kzalloc(sizeof(*h), GFP_KERNEL);
+	if (!h)
+		return ERR_PTR(-ENOMEM);
+
+	id.name = ALCHEMY_CPU_CLK;
+	id.parent_names = &parent_name;
+	id.num_parents = 1;
+	id.flags = 0;
+	id.ops = &alchemy_clkops_cpu;
+	h->init = &id;
+
+	clk = clk_register(NULL, h);
+	if (IS_ERR(clk)) {
+		pr_err("failed to register clock\n");
+		kfree(h);
+	}
+
+	return clk;
+}
+
+/* AUXPLLs ************************************************************/
+
+struct alchemy_auxpll_clk {
+	struct clk_hw hw;
+	unsigned long reg;	/* au1300 has also AUXPLL2 */
+	int maxmult;		/* max multiplier */
+};
+#define to_auxpll_clk(x) container_of(x, struct alchemy_auxpll_clk, hw)
+
+static unsigned long alchemy_clk_aux_recalc(struct clk_hw *hw,
+					    unsigned long parent_rate)
+{
+	struct alchemy_auxpll_clk *a = to_auxpll_clk(hw);
+
+	return (alchemy_rdsys(a->reg) & 0xff) * parent_rate;
+}
+
+static int alchemy_clk_aux_setr(struct clk_hw *hw,
+				unsigned long rate,
+				unsigned long parent_rate)
+{
+	struct alchemy_auxpll_clk *a = to_auxpll_clk(hw);
+	unsigned long d = rate;
+
+	if (rate)
+		d /= parent_rate;
+	else
+		d = 0;
+
+	/* minimum is 84MHz, max is 756-1032 depending on variant */
+	if (((d < 7) && (d != 0)) || (d > a->maxmult))
+		return -EINVAL;
+
+	alchemy_wrsys(d, a->reg);
+	return 0;
+}
+
+static long alchemy_clk_aux_roundr(struct clk_hw *hw,
+					    unsigned long rate,
+					    unsigned long *parent_rate)
+{
+	struct alchemy_auxpll_clk *a = to_auxpll_clk(hw);
+	unsigned long mult;
+
+	if (!rate || !*parent_rate)
+		return 0;
+
+	mult = rate / (*parent_rate);
+
+	if (mult && (mult < 7))
+		mult = 7;
+	if (mult > a->maxmult)
+		mult = a->maxmult;
+
+	return (*parent_rate) * mult;
+}
+
+static const struct clk_ops alchemy_clkops_aux = {
+	.recalc_rate	= alchemy_clk_aux_recalc,
+	.set_rate	= alchemy_clk_aux_setr,
+	.round_rate	= alchemy_clk_aux_roundr,
+};
+
+static struct clk __init *alchemy_clk_setup_aux(const char *parent_name,
+						char *name, int maxmult,
+						unsigned long reg)
+{
+	struct clk_init_data id;
+	struct clk *c;
+	struct alchemy_auxpll_clk *a;
+
+	a = kzalloc(sizeof(*a), GFP_KERNEL);
+	if (!a)
+		return ERR_PTR(-ENOMEM);
+
+	id.name = name;
+	id.parent_names = &parent_name;
+	id.num_parents = 1;
+	id.flags = CLK_GET_RATE_NOCACHE;
+	id.ops = &alchemy_clkops_aux;
+
+	a->reg = reg;
+	a->maxmult = maxmult;
+	a->hw.init = &id;
+
+	c = clk_register(NULL, &a->hw);
+	if (!IS_ERR(c))
+		clk_register_clkdev(c, name, NULL);
+	else
+		kfree(a);
+
+	return c;
+}
+
+/* sysbus_clk *********************************************************/
+
+static struct clk __init  *alchemy_clk_setup_sysbus(const char *pn)
+{
+	unsigned long v = (alchemy_rdsys(AU1000_SYS_POWERCTRL) & 3) + 2;
+	struct clk *c;
+
+	c = clk_register_fixed_factor(NULL, ALCHEMY_SYSBUS_CLK,
+				      pn, 0, 1, v);
+	if (!IS_ERR(c))
+		clk_register_clkdev(c, ALCHEMY_SYSBUS_CLK, NULL);
+	return c;
+}
+
+/* Peripheral Clock ***************************************************/
+
+static struct clk __init *alchemy_clk_setup_periph(const char *pn)
+{
+	/* Peripheral clock runs at half the rate of sysbus clk */
+	struct clk *c;
+
+	c = clk_register_fixed_factor(NULL, ALCHEMY_PERIPH_CLK,
+				      pn, 0, 1, 2);
+	if (!IS_ERR(c))
+		clk_register_clkdev(c, ALCHEMY_PERIPH_CLK, NULL);
+	return c;
+}
+
+/* mem clock **********************************************************/
+
+static struct clk __init *alchemy_clk_setup_mem(const char *pn, int ct)
+{
+	void __iomem *addr = IOMEM(AU1000_MEM_PHYS_ADDR);
+	unsigned long v;
+	struct clk *c;
+	int div;
+
+	switch (ct) {
+	case ALCHEMY_CPU_AU1550:
+	case ALCHEMY_CPU_AU1200:
+		v = __raw_readl(addr + AU1550_MEM_SDCONFIGB);
+		div = (v & (1 << 15)) ? 1 : 2;
+		break;
+	case ALCHEMY_CPU_AU1300:
+		v = __raw_readl(addr + AU1550_MEM_SDCONFIGB);
+		div = (v & (1 << 31)) ? 1 : 2;
+		break;
+	case ALCHEMY_CPU_AU1000:
+	case ALCHEMY_CPU_AU1500:
+	case ALCHEMY_CPU_AU1100:
+	default:
+		div = 2;
+		break;
+	}
+
+	c = clk_register_fixed_factor(NULL, ALCHEMY_MEM_CLK, pn,
+				      0, 1, div);
+	if (!IS_ERR(c))
+		clk_register_clkdev(c, ALCHEMY_MEM_CLK, NULL);
+	return c;
+}
+
+/* lrclk: external synchronous static bus clock ***********************/
+
+static struct clk __init *alchemy_clk_setup_lrclk(const char *pn, int t)
+{
+	/* Au1000, Au1500: MEM_STCFG0[11]: If bit is set, lrclk=pclk/5,
+	 * otherwise lrclk=pclk/4.
+	 * All other variants: MEM_STCFG0[15:13] = divisor.
+	 * L/RCLK = periph_clk / (divisor + 1)
+	 * On Au1000, Au1500, Au1100 it's called LCLK,
+	 * on later models it's called RCLK, but it's the same thing.
+	 */
+	struct clk *c;
+	unsigned long v = alchemy_rdsmem(AU1000_MEM_STCFG0);
+
+	switch (t) {
+	case ALCHEMY_CPU_AU1000:
+	case ALCHEMY_CPU_AU1500:
+		v = 4 + ((v >> 11) & 1);
+		break;
+	default:	/* all other models */
+		v = ((v >> 13) & 7) + 1;
+	}
+	c = clk_register_fixed_factor(NULL, ALCHEMY_LR_CLK,
+				      pn, 0, 1, v);
+	if (!IS_ERR(c))
+		clk_register_clkdev(c, ALCHEMY_LR_CLK, NULL);
+	return c;
+}
+
+/* Clock dividers and muxes *******************************************/
+
+/* data for fgen and csrc mux-dividers */
+struct alchemy_fgcs_clk {
+	struct clk_hw hw;
+	spinlock_t *reglock;	/* register lock		  */
+	unsigned long reg;	/* SYS_FREQCTRL0/1		  */
+	int shift;		/* offset in register		  */
+	int parent;		/* parent before disable [Au1300] */
+	int isen;		/* is it enabled?		  */
+	int *dt;		/* dividertable for csrc	  */
+};
+#define to_fgcs_clk(x) container_of(x, struct alchemy_fgcs_clk, hw)
+
+static long alchemy_calc_div(unsigned long rate, unsigned long prate,
+			       int scale, int maxdiv, unsigned long *rv)
+{
+	long div1, div2;
+
+	div1 = prate / rate;
+	if ((prate / div1) > rate)
+		div1++;
+
+	if (scale == 2) {	/* only div-by-multiple-of-2 possible */
+		if (div1 & 1)
+			div1++;	/* stay <=prate */
+	}
+
+	div2 = (div1 / scale) - 1;	/* value to write to register */
+
+	if (div2 > maxdiv)
+		div2 = maxdiv;
+	if (rv)
+		*rv = div2;
+
+	div1 = ((div2 + 1) * scale);
+	return div1;
+}
+
+static int alchemy_clk_fgcs_detr(struct clk_hw *hw,
+				 struct clk_rate_request *req,
+				 int scale, int maxdiv)
+{
+	struct clk_hw *pc, *bpc, *free;
+	long tdv, tpr, pr, nr, br, bpr, diff, lastdiff;
+	int j;
+
+	lastdiff = INT_MAX;
+	bpr = 0;
+	bpc = NULL;
+	br = -EINVAL;
+	free = NULL;
+
+	/* look at the rates each enabled parent supplies and select
+	 * the one that gets closest to but not over the requested rate.
+	 */
+	for (j = 0; j < 7; j++) {
+		pc = clk_hw_get_parent_by_index(hw, j);
+		if (!pc)
+			break;
+
+		/* if this parent is currently unused, remember it.
+		 * XXX: we would actually want clk_has_active_children()
+		 * but this is a good-enough approximation for now.
+		 */
+		if (!clk_hw_is_prepared(pc)) {
+			if (!free)
+				free = pc;
+		}
+
+		pr = clk_hw_get_rate(pc);
+		if (pr < req->rate)
+			continue;
+
+		/* what can hardware actually provide */
+		tdv = alchemy_calc_div(req->rate, pr, scale, maxdiv, NULL);
+		nr = pr / tdv;
+		diff = req->rate - nr;
+		if (nr > req->rate)
+			continue;
+
+		if (diff < lastdiff) {
+			lastdiff = diff;
+			bpr = pr;
+			bpc = pc;
+			br = nr;
+		}
+		if (diff == 0)
+			break;
+	}
+
+	/* if we couldn't get the exact rate we wanted from the enabled
+	 * parents, maybe we can tell an available disabled/inactive one
+	 * to give us a rate we can divide down to the requested rate.
+	 */
+	if (lastdiff && free) {
+		for (j = (maxdiv == 4) ? 1 : scale; j <= maxdiv; j += scale) {
+			tpr = req->rate * j;
+			if (tpr < 0)
+				break;
+			pr = clk_hw_round_rate(free, tpr);
+
+			tdv = alchemy_calc_div(req->rate, pr, scale, maxdiv,
+					       NULL);
+			nr = pr / tdv;
+			diff = req->rate - nr;
+			if (nr > req->rate)
+				continue;
+			if (diff < lastdiff) {
+				lastdiff = diff;
+				bpr = pr;
+				bpc = free;
+				br = nr;
+			}
+			if (diff == 0)
+				break;
+		}
+	}
+
+	if (br < 0)
+		return br;
+
+	req->best_parent_rate = bpr;
+	req->best_parent_hw = bpc;
+	req->rate = br;
+
+	return 0;
+}
+
+static int alchemy_clk_fgv1_en(struct clk_hw *hw)
+{
+	struct alchemy_fgcs_clk *c = to_fgcs_clk(hw);
+	unsigned long v, flags;
+
+	spin_lock_irqsave(c->reglock, flags);
+	v = alchemy_rdsys(c->reg);
+	v |= (1 << 1) << c->shift;
+	alchemy_wrsys(v, c->reg);
+	spin_unlock_irqrestore(c->reglock, flags);
+
+	return 0;
+}
+
+static int alchemy_clk_fgv1_isen(struct clk_hw *hw)
+{
+	struct alchemy_fgcs_clk *c = to_fgcs_clk(hw);
+	unsigned long v = alchemy_rdsys(c->reg) >> (c->shift + 1);
+
+	return v & 1;
+}
+
+static void alchemy_clk_fgv1_dis(struct clk_hw *hw)
+{
+	struct alchemy_fgcs_clk *c = to_fgcs_clk(hw);
+	unsigned long v, flags;
+
+	spin_lock_irqsave(c->reglock, flags);
+	v = alchemy_rdsys(c->reg);
+	v &= ~((1 << 1) << c->shift);
+	alchemy_wrsys(v, c->reg);
+	spin_unlock_irqrestore(c->reglock, flags);
+}
+
+static int alchemy_clk_fgv1_setp(struct clk_hw *hw, u8 index)
+{
+	struct alchemy_fgcs_clk *c = to_fgcs_clk(hw);
+	unsigned long v, flags;
+
+	spin_lock_irqsave(c->reglock, flags);
+	v = alchemy_rdsys(c->reg);
+	if (index)
+		v |= (1 << c->shift);
+	else
+		v &= ~(1 << c->shift);
+	alchemy_wrsys(v, c->reg);
+	spin_unlock_irqrestore(c->reglock, flags);
+
+	return 0;
+}
+
+static u8 alchemy_clk_fgv1_getp(struct clk_hw *hw)
+{
+	struct alchemy_fgcs_clk *c = to_fgcs_clk(hw);
+
+	return (alchemy_rdsys(c->reg) >> c->shift) & 1;
+}
+
+static int alchemy_clk_fgv1_setr(struct clk_hw *hw, unsigned long rate,
+				 unsigned long parent_rate)
+{
+	struct alchemy_fgcs_clk *c = to_fgcs_clk(hw);
+	unsigned long div, v, flags, ret;
+	int sh = c->shift + 2;
+
+	if (!rate || !parent_rate || rate > (parent_rate / 2))
+		return -EINVAL;
+	ret = alchemy_calc_div(rate, parent_rate, 2, 512, &div);
+	spin_lock_irqsave(c->reglock, flags);
+	v = alchemy_rdsys(c->reg);
+	v &= ~(0xff << sh);
+	v |= div << sh;
+	alchemy_wrsys(v, c->reg);
+	spin_unlock_irqrestore(c->reglock, flags);
+
+	return 0;
+}
+
+static unsigned long alchemy_clk_fgv1_recalc(struct clk_hw *hw,
+					     unsigned long parent_rate)
+{
+	struct alchemy_fgcs_clk *c = to_fgcs_clk(hw);
+	unsigned long v = alchemy_rdsys(c->reg) >> (c->shift + 2);
+
+	v = ((v & 0xff) + 1) * 2;
+	return parent_rate / v;
+}
+
+static int alchemy_clk_fgv1_detr(struct clk_hw *hw,
+				 struct clk_rate_request *req)
+{
+	return alchemy_clk_fgcs_detr(hw, req, 2, 512);
+}
+
+/* Au1000, Au1100, Au15x0, Au12x0 */
+static const struct clk_ops alchemy_clkops_fgenv1 = {
+	.recalc_rate	= alchemy_clk_fgv1_recalc,
+	.determine_rate	= alchemy_clk_fgv1_detr,
+	.set_rate	= alchemy_clk_fgv1_setr,
+	.set_parent	= alchemy_clk_fgv1_setp,
+	.get_parent	= alchemy_clk_fgv1_getp,
+	.enable		= alchemy_clk_fgv1_en,
+	.disable	= alchemy_clk_fgv1_dis,
+	.is_enabled	= alchemy_clk_fgv1_isen,
+};
+
+static void __alchemy_clk_fgv2_en(struct alchemy_fgcs_clk *c)
+{
+	unsigned long v = alchemy_rdsys(c->reg);
+
+	v &= ~(3 << c->shift);
+	v |= (c->parent & 3) << c->shift;
+	alchemy_wrsys(v, c->reg);
+	c->isen = 1;
+}
+
+static int alchemy_clk_fgv2_en(struct clk_hw *hw)
+{
+	struct alchemy_fgcs_clk *c = to_fgcs_clk(hw);
+	unsigned long flags;
+
+	/* enable by setting the previous parent clock */
+	spin_lock_irqsave(c->reglock, flags);
+	__alchemy_clk_fgv2_en(c);
+	spin_unlock_irqrestore(c->reglock, flags);
+
+	return 0;
+}
+
+static int alchemy_clk_fgv2_isen(struct clk_hw *hw)
+{
+	struct alchemy_fgcs_clk *c = to_fgcs_clk(hw);
+
+	return ((alchemy_rdsys(c->reg) >> c->shift) & 3) != 0;
+}
+
+static void alchemy_clk_fgv2_dis(struct clk_hw *hw)
+{
+	struct alchemy_fgcs_clk *c = to_fgcs_clk(hw);
+	unsigned long v, flags;
+
+	spin_lock_irqsave(c->reglock, flags);
+	v = alchemy_rdsys(c->reg);
+	v &= ~(3 << c->shift);	/* set input mux to "disabled" state */
+	alchemy_wrsys(v, c->reg);
+	c->isen = 0;
+	spin_unlock_irqrestore(c->reglock, flags);
+}
+
+static int alchemy_clk_fgv2_setp(struct clk_hw *hw, u8 index)
+{
+	struct alchemy_fgcs_clk *c = to_fgcs_clk(hw);
+	unsigned long flags;
+
+	spin_lock_irqsave(c->reglock, flags);
+	c->parent = index + 1;	/* value to write to register */
+	if (c->isen)
+		__alchemy_clk_fgv2_en(c);
+	spin_unlock_irqrestore(c->reglock, flags);
+
+	return 0;
+}
+
+static u8 alchemy_clk_fgv2_getp(struct clk_hw *hw)
+{
+	struct alchemy_fgcs_clk *c = to_fgcs_clk(hw);
+	unsigned long flags, v;
+
+	spin_lock_irqsave(c->reglock, flags);
+	v = c->parent - 1;
+	spin_unlock_irqrestore(c->reglock, flags);
+	return v;
+}
+
+/* fg0-2 and fg4-6 share a "scale"-bit. With this bit cleared, the
+ * dividers behave exactly as on previous models (dividers are multiples
+ * of 2); with the bit set, dividers are multiples of 1, halving their
+ * range, but making them also much more flexible.
+ */
+static int alchemy_clk_fgv2_setr(struct clk_hw *hw, unsigned long rate,
+				 unsigned long parent_rate)
+{
+	struct alchemy_fgcs_clk *c = to_fgcs_clk(hw);
+	int sh = c->shift + 2;
+	unsigned long div, v, flags, ret;
+
+	if (!rate || !parent_rate || rate > parent_rate)
+		return -EINVAL;
+
+	v = alchemy_rdsys(c->reg) & (1 << 30); /* test "scale" bit */
+	ret = alchemy_calc_div(rate, parent_rate, v ? 1 : 2,
+			       v ? 256 : 512, &div);
+
+	spin_lock_irqsave(c->reglock, flags);
+	v = alchemy_rdsys(c->reg);
+	v &= ~(0xff << sh);
+	v |= (div & 0xff) << sh;
+	alchemy_wrsys(v, c->reg);
+	spin_unlock_irqrestore(c->reglock, flags);
+
+	return 0;
+}
+
+static unsigned long alchemy_clk_fgv2_recalc(struct clk_hw *hw,
+					     unsigned long parent_rate)
+{
+	struct alchemy_fgcs_clk *c = to_fgcs_clk(hw);
+	int sh = c->shift + 2;
+	unsigned long v, t;
+
+	v = alchemy_rdsys(c->reg);
+	t = parent_rate / (((v >> sh) & 0xff) + 1);
+	if ((v & (1 << 30)) == 0)		/* test scale bit */
+		t /= 2;
+
+	return t;
+}
+
+static int alchemy_clk_fgv2_detr(struct clk_hw *hw,
+				 struct clk_rate_request *req)
+{
+	struct alchemy_fgcs_clk *c = to_fgcs_clk(hw);
+	int scale, maxdiv;
+
+	if (alchemy_rdsys(c->reg) & (1 << 30)) {
+		scale = 1;
+		maxdiv = 256;
+	} else {
+		scale = 2;
+		maxdiv = 512;
+	}
+
+	return alchemy_clk_fgcs_detr(hw, req, scale, maxdiv);
+}
+
+/* Au1300 larger input mux, no separate disable bit, flexible divider */
+static const struct clk_ops alchemy_clkops_fgenv2 = {
+	.recalc_rate	= alchemy_clk_fgv2_recalc,
+	.determine_rate	= alchemy_clk_fgv2_detr,
+	.set_rate	= alchemy_clk_fgv2_setr,
+	.set_parent	= alchemy_clk_fgv2_setp,
+	.get_parent	= alchemy_clk_fgv2_getp,
+	.enable		= alchemy_clk_fgv2_en,
+	.disable	= alchemy_clk_fgv2_dis,
+	.is_enabled	= alchemy_clk_fgv2_isen,
+};
+
+static const char * const alchemy_clk_fgv1_parents[] = {
+	ALCHEMY_CPU_CLK, ALCHEMY_AUXPLL_CLK
+};
+
+static const char * const alchemy_clk_fgv2_parents[] = {
+	ALCHEMY_AUXPLL2_CLK, ALCHEMY_CPU_CLK, ALCHEMY_AUXPLL_CLK
+};
+
+static const char * const alchemy_clk_fgen_names[] = {
+	ALCHEMY_FG0_CLK, ALCHEMY_FG1_CLK, ALCHEMY_FG2_CLK,
+	ALCHEMY_FG3_CLK, ALCHEMY_FG4_CLK, ALCHEMY_FG5_CLK };
+
+static int __init alchemy_clk_init_fgens(int ctype)
+{
+	struct clk *c;
+	struct clk_init_data id;
+	struct alchemy_fgcs_clk *a;
+	unsigned long v;
+	int i, ret;
+
+	switch (ctype) {
+	case ALCHEMY_CPU_AU1000...ALCHEMY_CPU_AU1200:
+		id.ops = &alchemy_clkops_fgenv1;
+		id.parent_names = alchemy_clk_fgv1_parents;
+		id.num_parents = 2;
+		break;
+	case ALCHEMY_CPU_AU1300:
+		id.ops = &alchemy_clkops_fgenv2;
+		id.parent_names = alchemy_clk_fgv2_parents;
+		id.num_parents = 3;
+		break;
+	default:
+		return -ENODEV;
+	}
+	id.flags = CLK_SET_RATE_PARENT | CLK_GET_RATE_NOCACHE;
+
+	a = kzalloc((sizeof(*a)) * 6, GFP_KERNEL);
+	if (!a)
+		return -ENOMEM;
+
+	spin_lock_init(&alchemy_clk_fg0_lock);
+	spin_lock_init(&alchemy_clk_fg1_lock);
+	ret = 0;
+	for (i = 0; i < 6; i++) {
+		id.name = alchemy_clk_fgen_names[i];
+		a->shift = 10 * (i < 3 ? i : i - 3);
+		if (i > 2) {
+			a->reg = AU1000_SYS_FREQCTRL1;
+			a->reglock = &alchemy_clk_fg1_lock;
+		} else {
+			a->reg = AU1000_SYS_FREQCTRL0;
+			a->reglock = &alchemy_clk_fg0_lock;
+		}
+
+		/* default to first parent if bootloader has set
+		 * the mux to disabled state.
+		 */
+		if (ctype == ALCHEMY_CPU_AU1300) {
+			v = alchemy_rdsys(a->reg);
+			a->parent = (v >> a->shift) & 3;
+			if (!a->parent) {
+				a->parent = 1;
+				a->isen = 0;
+			} else
+				a->isen = 1;
+		}
+
+		a->hw.init = &id;
+		c = clk_register(NULL, &a->hw);
+		if (IS_ERR(c))
+			ret++;
+		else
+			clk_register_clkdev(c, id.name, NULL);
+		a++;
+	}
+
+	return ret;
+}
+
+/* internal sources muxes *********************************************/
+
+static int alchemy_clk_csrc_isen(struct clk_hw *hw)
+{
+	struct alchemy_fgcs_clk *c = to_fgcs_clk(hw);
+	unsigned long v = alchemy_rdsys(c->reg);
+
+	return (((v >> c->shift) >> 2) & 7) != 0;
+}
+
+static void __alchemy_clk_csrc_en(struct alchemy_fgcs_clk *c)
+{
+	unsigned long v = alchemy_rdsys(c->reg);
+
+	v &= ~((7 << 2) << c->shift);
+	v |= ((c->parent & 7) << 2) << c->shift;
+	alchemy_wrsys(v, c->reg);
+	c->isen = 1;
+}
+
+static int alchemy_clk_csrc_en(struct clk_hw *hw)
+{
+	struct alchemy_fgcs_clk *c = to_fgcs_clk(hw);
+	unsigned long flags;
+
+	/* enable by setting the previous parent clock */
+	spin_lock_irqsave(c->reglock, flags);
+	__alchemy_clk_csrc_en(c);
+	spin_unlock_irqrestore(c->reglock, flags);
+
+	return 0;
+}
+
+static void alchemy_clk_csrc_dis(struct clk_hw *hw)
+{
+	struct alchemy_fgcs_clk *c = to_fgcs_clk(hw);
+	unsigned long v, flags;
+
+	spin_lock_irqsave(c->reglock, flags);
+	v = alchemy_rdsys(c->reg);
+	v &= ~((3 << 2) << c->shift);	/* mux to "disabled" state */
+	alchemy_wrsys(v, c->reg);
+	c->isen = 0;
+	spin_unlock_irqrestore(c->reglock, flags);
+}
+
+static int alchemy_clk_csrc_setp(struct clk_hw *hw, u8 index)
+{
+	struct alchemy_fgcs_clk *c = to_fgcs_clk(hw);
+	unsigned long flags;
+
+	spin_lock_irqsave(c->reglock, flags);
+	c->parent = index + 1;	/* value to write to register */
+	if (c->isen)
+		__alchemy_clk_csrc_en(c);
+	spin_unlock_irqrestore(c->reglock, flags);
+
+	return 0;
+}
+
+static u8 alchemy_clk_csrc_getp(struct clk_hw *hw)
+{
+	struct alchemy_fgcs_clk *c = to_fgcs_clk(hw);
+
+	return c->parent - 1;
+}
+
+static unsigned long alchemy_clk_csrc_recalc(struct clk_hw *hw,
+					     unsigned long parent_rate)
+{
+	struct alchemy_fgcs_clk *c = to_fgcs_clk(hw);
+	unsigned long v = (alchemy_rdsys(c->reg) >> c->shift) & 3;
+
+	return parent_rate / c->dt[v];
+}
+
+static int alchemy_clk_csrc_setr(struct clk_hw *hw, unsigned long rate,
+				 unsigned long parent_rate)
+{
+	struct alchemy_fgcs_clk *c = to_fgcs_clk(hw);
+	unsigned long d, v, flags;
+	int i;
+
+	if (!rate || !parent_rate || rate > parent_rate)
+		return -EINVAL;
+
+	d = (parent_rate + (rate / 2)) / rate;
+	if (d > 4)
+		return -EINVAL;
+	if ((d == 3) && (c->dt[2] != 3))
+		d = 4;
+
+	for (i = 0; i < 4; i++)
+		if (c->dt[i] == d)
+			break;
+
+	if (i >= 4)
+		return -EINVAL;	/* oops */
+
+	spin_lock_irqsave(c->reglock, flags);
+	v = alchemy_rdsys(c->reg);
+	v &= ~(3 << c->shift);
+	v |= (i & 3) << c->shift;
+	alchemy_wrsys(v, c->reg);
+	spin_unlock_irqrestore(c->reglock, flags);
+
+	return 0;
+}
+
+static int alchemy_clk_csrc_detr(struct clk_hw *hw,
+				 struct clk_rate_request *req)
+{
+	struct alchemy_fgcs_clk *c = to_fgcs_clk(hw);
+	int scale = c->dt[2] == 3 ? 1 : 2; /* au1300 check */
+
+	return alchemy_clk_fgcs_detr(hw, req, scale, 4);
+}
+
+static const struct clk_ops alchemy_clkops_csrc = {
+	.recalc_rate	= alchemy_clk_csrc_recalc,
+	.determine_rate	= alchemy_clk_csrc_detr,
+	.set_rate	= alchemy_clk_csrc_setr,
+	.set_parent	= alchemy_clk_csrc_setp,
+	.get_parent	= alchemy_clk_csrc_getp,
+	.enable		= alchemy_clk_csrc_en,
+	.disable	= alchemy_clk_csrc_dis,
+	.is_enabled	= alchemy_clk_csrc_isen,
+};
+
+static const char * const alchemy_clk_csrc_parents[] = {
+	/* disabled at index 0 */ ALCHEMY_AUXPLL_CLK,
+	ALCHEMY_FG0_CLK, ALCHEMY_FG1_CLK, ALCHEMY_FG2_CLK,
+	ALCHEMY_FG3_CLK, ALCHEMY_FG4_CLK, ALCHEMY_FG5_CLK
+};
+
+/* divider tables */
+static int alchemy_csrc_dt1[] = { 1, 4, 1, 2 };	/* rest */
+static int alchemy_csrc_dt2[] = { 1, 4, 3, 2 };	/* Au1300 */
+
+static int __init alchemy_clk_setup_imux(int ctype)
+{
+	struct alchemy_fgcs_clk *a;
+	const char * const *names;
+	struct clk_init_data id;
+	unsigned long v;
+	int i, ret, *dt;
+	struct clk *c;
+
+	id.ops = &alchemy_clkops_csrc;
+	id.parent_names = alchemy_clk_csrc_parents;
+	id.num_parents = 7;
+	id.flags = CLK_SET_RATE_PARENT | CLK_GET_RATE_NOCACHE;
+
+	dt = alchemy_csrc_dt1;
+	switch (ctype) {
+	case ALCHEMY_CPU_AU1000:
+		names = alchemy_au1000_intclknames;
+		break;
+	case ALCHEMY_CPU_AU1500:
+		names = alchemy_au1500_intclknames;
+		break;
+	case ALCHEMY_CPU_AU1100:
+		names = alchemy_au1100_intclknames;
+		break;
+	case ALCHEMY_CPU_AU1550:
+		names = alchemy_au1550_intclknames;
+		break;
+	case ALCHEMY_CPU_AU1200:
+		names = alchemy_au1200_intclknames;
+		break;
+	case ALCHEMY_CPU_AU1300:
+		dt = alchemy_csrc_dt2;
+		names = alchemy_au1300_intclknames;
+		break;
+	default:
+		return -ENODEV;
+	}
+
+	a = kcalloc(6, sizeof(*a), GFP_KERNEL);
+	if (!a)
+		return -ENOMEM;
+
+	ret = 0;
+
+	for (i = 0; i < 6; i++) {
+		id.name = names[i];
+		if (!id.name)
+			goto next;
+
+		a->shift = i * 5;
+		a->reg = AU1000_SYS_CLKSRC;
+		a->reglock = &alchemy_clk_csrc_lock;
+		a->dt = dt;
+
+		/* default to first parent clock if mux is initially
+		 * set to disabled state.
+		 */
+		v = alchemy_rdsys(a->reg);
+		a->parent = ((v >> a->shift) >> 2) & 7;
+		if (!a->parent) {
+			a->parent = 1;
+			a->isen = 0;
+		} else
+			a->isen = 1;
+
+		a->hw.init = &id;
+		c = clk_register(NULL, &a->hw);
+		if (IS_ERR(c))
+			ret++;
+		else
+			clk_register_clkdev(c, id.name, NULL);
+next:
+		a++;
+	}
+
+	return ret;
+}
+
+
+/**********************************************************************/
+
+
+#define ERRCK(x)						\
+	if (IS_ERR(x)) {					\
+		ret = PTR_ERR(x);				\
+		goto out;					\
+	}
+
+static int __init alchemy_clk_init(void)
+{
+	int ctype = alchemy_get_cputype(), ret, i;
+	struct clk_aliastable *t = alchemy_clk_aliases;
+	struct clk *c;
+
+	/* Root of the Alchemy clock tree: external 12MHz crystal osc */
+	c = clk_register_fixed_rate(NULL, ALCHEMY_ROOT_CLK, NULL,
+					   0, ALCHEMY_ROOTCLK_RATE);
+	ERRCK(c)
+
+	/* CPU core clock */
+	c = alchemy_clk_setup_cpu(ALCHEMY_ROOT_CLK, ctype);
+	ERRCK(c)
+
+	/* AUXPLLs: max 1GHz on Au1300, 748MHz on older models */
+	i = (ctype == ALCHEMY_CPU_AU1300) ? 84 : 63;
+	c = alchemy_clk_setup_aux(ALCHEMY_ROOT_CLK, ALCHEMY_AUXPLL_CLK,
+				  i, AU1000_SYS_AUXPLL);
+	ERRCK(c)
+
+	if (ctype == ALCHEMY_CPU_AU1300) {
+		c = alchemy_clk_setup_aux(ALCHEMY_ROOT_CLK,
+					  ALCHEMY_AUXPLL2_CLK, i,
+					  AU1300_SYS_AUXPLL2);
+		ERRCK(c)
+	}
+
+	/* sysbus clock: cpu core clock divided by 2, 3 or 4 */
+	c = alchemy_clk_setup_sysbus(ALCHEMY_CPU_CLK);
+	ERRCK(c)
+
+	/* peripheral clock: runs at half rate of sysbus clk */
+	c = alchemy_clk_setup_periph(ALCHEMY_SYSBUS_CLK);
+	ERRCK(c)
+
+	/* SDR/DDR memory clock */
+	c = alchemy_clk_setup_mem(ALCHEMY_SYSBUS_CLK, ctype);
+	ERRCK(c)
+
+	/* L/RCLK: external static bus clock for synchronous mode */
+	c = alchemy_clk_setup_lrclk(ALCHEMY_PERIPH_CLK, ctype);
+	ERRCK(c)
+
+	/* Frequency dividers 0-5 */
+	ret = alchemy_clk_init_fgens(ctype);
+	if (ret) {
+		ret = -ENODEV;
+		goto out;
+	}
+
+	/* diving muxes for internal sources */
+	ret = alchemy_clk_setup_imux(ctype);
+	if (ret) {
+		ret = -ENODEV;
+		goto out;
+	}
+
+	/* set up aliases drivers might look for */
+	while (t->base) {
+		if (t->cputype == ctype)
+			clk_add_alias(t->alias, NULL, t->base, NULL);
+		t++;
+	}
+
+	pr_info("Alchemy clocktree installed\n");
+	return 0;
+
+out:
+	return ret;
+}
+postcore_initcall(alchemy_clk_init);
diff --git a/arch/mips/alchemy/common/dbdma.c b/arch/mips/alchemy/common/dbdma.c
new file mode 100644
index 000000000..6a3c890f7
--- /dev/null
+++ b/arch/mips/alchemy/common/dbdma.c
@@ -0,0 +1,1092 @@
+/*
+ *
+ * BRIEF MODULE DESCRIPTION
+ *      The Descriptor Based DMA channel manager that first appeared
+ *	on the Au1550.  I started with dma.c, but I think all that is
+ *	left is this initial comment :-)
+ *
+ * Copyright 2004 Embedded Edge, LLC
+ *	dan@embeddededge.com
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ */
+
+#include <linux/dma-map-ops.h> /* for dma_default_coherent */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+#include <linux/interrupt.h>
+#include <linux/export.h>
+#include <linux/syscore_ops.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1xxx_dbdma.h>
+
+/*
+ * The Descriptor Based DMA supports up to 16 channels.
+ *
+ * There are 32 devices defined. We keep an internal structure
+ * of devices using these channels, along with additional
+ * information.
+ *
+ * We allocate the descriptors and allow access to them through various
+ * functions.  The drivers allocate the data buffers and assign them
+ * to the descriptors.
+ */
+static DEFINE_SPINLOCK(au1xxx_dbdma_spin_lock);
+
+/* I couldn't find a macro that did this... */
+#define ALIGN_ADDR(x, a)	((((u32)(x)) + (a-1)) & ~(a-1))
+
+static dbdma_global_t *dbdma_gptr =
+			(dbdma_global_t *)KSEG1ADDR(AU1550_DBDMA_CONF_PHYS_ADDR);
+static int dbdma_initialized;
+
+static dbdev_tab_t *dbdev_tab;
+
+static dbdev_tab_t au1550_dbdev_tab[] __initdata = {
+	/* UARTS */
+	{ AU1550_DSCR_CMD0_UART0_TX, DEV_FLAGS_OUT, 0, 8, 0x11100004, 0, 0 },
+	{ AU1550_DSCR_CMD0_UART0_RX, DEV_FLAGS_IN,  0, 8, 0x11100000, 0, 0 },
+	{ AU1550_DSCR_CMD0_UART3_TX, DEV_FLAGS_OUT, 0, 8, 0x11400004, 0, 0 },
+	{ AU1550_DSCR_CMD0_UART3_RX, DEV_FLAGS_IN,  0, 8, 0x11400000, 0, 0 },
+
+	/* EXT DMA */
+	{ AU1550_DSCR_CMD0_DMA_REQ0, 0, 0, 0, 0x00000000, 0, 0 },
+	{ AU1550_DSCR_CMD0_DMA_REQ1, 0, 0, 0, 0x00000000, 0, 0 },
+	{ AU1550_DSCR_CMD0_DMA_REQ2, 0, 0, 0, 0x00000000, 0, 0 },
+	{ AU1550_DSCR_CMD0_DMA_REQ3, 0, 0, 0, 0x00000000, 0, 0 },
+
+	/* USB DEV */
+	{ AU1550_DSCR_CMD0_USBDEV_RX0, DEV_FLAGS_IN,  4, 8, 0x10200000, 0, 0 },
+	{ AU1550_DSCR_CMD0_USBDEV_TX0, DEV_FLAGS_OUT, 4, 8, 0x10200004, 0, 0 },
+	{ AU1550_DSCR_CMD0_USBDEV_TX1, DEV_FLAGS_OUT, 4, 8, 0x10200008, 0, 0 },
+	{ AU1550_DSCR_CMD0_USBDEV_TX2, DEV_FLAGS_OUT, 4, 8, 0x1020000c, 0, 0 },
+	{ AU1550_DSCR_CMD0_USBDEV_RX3, DEV_FLAGS_IN,  4, 8, 0x10200010, 0, 0 },
+	{ AU1550_DSCR_CMD0_USBDEV_RX4, DEV_FLAGS_IN,  4, 8, 0x10200014, 0, 0 },
+
+	/* PSCs */
+	{ AU1550_DSCR_CMD0_PSC0_TX, DEV_FLAGS_OUT, 0, 0, 0x11a0001c, 0, 0 },
+	{ AU1550_DSCR_CMD0_PSC0_RX, DEV_FLAGS_IN,  0, 0, 0x11a0001c, 0, 0 },
+	{ AU1550_DSCR_CMD0_PSC1_TX, DEV_FLAGS_OUT, 0, 0, 0x11b0001c, 0, 0 },
+	{ AU1550_DSCR_CMD0_PSC1_RX, DEV_FLAGS_IN,  0, 0, 0x11b0001c, 0, 0 },
+	{ AU1550_DSCR_CMD0_PSC2_TX, DEV_FLAGS_OUT, 0, 0, 0x10a0001c, 0, 0 },
+	{ AU1550_DSCR_CMD0_PSC2_RX, DEV_FLAGS_IN,  0, 0, 0x10a0001c, 0, 0 },
+	{ AU1550_DSCR_CMD0_PSC3_TX, DEV_FLAGS_OUT, 0, 0, 0x10b0001c, 0, 0 },
+	{ AU1550_DSCR_CMD0_PSC3_RX, DEV_FLAGS_IN,  0, 0, 0x10b0001c, 0, 0 },
+
+	{ AU1550_DSCR_CMD0_PCI_WRITE,  0, 0, 0, 0x00000000, 0, 0 },  /* PCI */
+	{ AU1550_DSCR_CMD0_NAND_FLASH, 0, 0, 0, 0x00000000, 0, 0 }, /* NAND */
+
+	/* MAC 0 */
+	{ AU1550_DSCR_CMD0_MAC0_RX, DEV_FLAGS_IN,  0, 0, 0x00000000, 0, 0 },
+	{ AU1550_DSCR_CMD0_MAC0_TX, DEV_FLAGS_OUT, 0, 0, 0x00000000, 0, 0 },
+
+	/* MAC 1 */
+	{ AU1550_DSCR_CMD0_MAC1_RX, DEV_FLAGS_IN,  0, 0, 0x00000000, 0, 0 },
+	{ AU1550_DSCR_CMD0_MAC1_TX, DEV_FLAGS_OUT, 0, 0, 0x00000000, 0, 0 },
+
+	{ DSCR_CMD0_THROTTLE, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 },
+	{ DSCR_CMD0_ALWAYS,   DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 },
+};
+
+static dbdev_tab_t au1200_dbdev_tab[] __initdata = {
+	{ AU1200_DSCR_CMD0_UART0_TX, DEV_FLAGS_OUT, 0, 8, 0x11100004, 0, 0 },
+	{ AU1200_DSCR_CMD0_UART0_RX, DEV_FLAGS_IN,  0, 8, 0x11100000, 0, 0 },
+	{ AU1200_DSCR_CMD0_UART1_TX, DEV_FLAGS_OUT, 0, 8, 0x11200004, 0, 0 },
+	{ AU1200_DSCR_CMD0_UART1_RX, DEV_FLAGS_IN,  0, 8, 0x11200000, 0, 0 },
+
+	{ AU1200_DSCR_CMD0_DMA_REQ0, 0, 0, 0, 0x00000000, 0, 0 },
+	{ AU1200_DSCR_CMD0_DMA_REQ1, 0, 0, 0, 0x00000000, 0, 0 },
+
+	{ AU1200_DSCR_CMD0_MAE_BE, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 },
+	{ AU1200_DSCR_CMD0_MAE_FE, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 },
+	{ AU1200_DSCR_CMD0_MAE_BOTH, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 },
+	{ AU1200_DSCR_CMD0_LCD, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 },
+
+	{ AU1200_DSCR_CMD0_SDMS_TX0, DEV_FLAGS_OUT, 4, 8, 0x10600000, 0, 0 },
+	{ AU1200_DSCR_CMD0_SDMS_RX0, DEV_FLAGS_IN,  4, 8, 0x10600004, 0, 0 },
+	{ AU1200_DSCR_CMD0_SDMS_TX1, DEV_FLAGS_OUT, 4, 8, 0x10680000, 0, 0 },
+	{ AU1200_DSCR_CMD0_SDMS_RX1, DEV_FLAGS_IN,  4, 8, 0x10680004, 0, 0 },
+
+	{ AU1200_DSCR_CMD0_AES_RX, DEV_FLAGS_IN , 4, 32, 0x10300008, 0, 0 },
+	{ AU1200_DSCR_CMD0_AES_TX, DEV_FLAGS_OUT, 4, 32, 0x10300004, 0, 0 },
+
+	{ AU1200_DSCR_CMD0_PSC0_TX,   DEV_FLAGS_OUT, 0, 16, 0x11a0001c, 0, 0 },
+	{ AU1200_DSCR_CMD0_PSC0_RX,   DEV_FLAGS_IN,  0, 16, 0x11a0001c, 0, 0 },
+	{ AU1200_DSCR_CMD0_PSC0_SYNC, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 },
+	{ AU1200_DSCR_CMD0_PSC1_TX,   DEV_FLAGS_OUT, 0, 16, 0x11b0001c, 0, 0 },
+	{ AU1200_DSCR_CMD0_PSC1_RX,   DEV_FLAGS_IN,  0, 16, 0x11b0001c, 0, 0 },
+	{ AU1200_DSCR_CMD0_PSC1_SYNC, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 },
+
+	{ AU1200_DSCR_CMD0_CIM_RXA,  DEV_FLAGS_IN, 0, 32, 0x14004020, 0, 0 },
+	{ AU1200_DSCR_CMD0_CIM_RXB,  DEV_FLAGS_IN, 0, 32, 0x14004040, 0, 0 },
+	{ AU1200_DSCR_CMD0_CIM_RXC,  DEV_FLAGS_IN, 0, 32, 0x14004060, 0, 0 },
+	{ AU1200_DSCR_CMD0_CIM_SYNC, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 },
+
+	{ AU1200_DSCR_CMD0_NAND_FLASH, DEV_FLAGS_IN, 0, 0, 0x00000000, 0, 0 },
+
+	{ DSCR_CMD0_THROTTLE, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 },
+	{ DSCR_CMD0_ALWAYS,   DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 },
+};
+
+static dbdev_tab_t au1300_dbdev_tab[] __initdata = {
+	{ AU1300_DSCR_CMD0_UART0_TX, DEV_FLAGS_OUT, 0, 8,  0x10100004, 0, 0 },
+	{ AU1300_DSCR_CMD0_UART0_RX, DEV_FLAGS_IN,  0, 8,  0x10100000, 0, 0 },
+	{ AU1300_DSCR_CMD0_UART1_TX, DEV_FLAGS_OUT, 0, 8,  0x10101004, 0, 0 },
+	{ AU1300_DSCR_CMD0_UART1_RX, DEV_FLAGS_IN,  0, 8,  0x10101000, 0, 0 },
+	{ AU1300_DSCR_CMD0_UART2_TX, DEV_FLAGS_OUT, 0, 8,  0x10102004, 0, 0 },
+	{ AU1300_DSCR_CMD0_UART2_RX, DEV_FLAGS_IN,  0, 8,  0x10102000, 0, 0 },
+	{ AU1300_DSCR_CMD0_UART3_TX, DEV_FLAGS_OUT, 0, 8,  0x10103004, 0, 0 },
+	{ AU1300_DSCR_CMD0_UART3_RX, DEV_FLAGS_IN,  0, 8,  0x10103000, 0, 0 },
+
+	{ AU1300_DSCR_CMD0_SDMS_TX0, DEV_FLAGS_OUT, 4, 8,  0x10600000, 0, 0 },
+	{ AU1300_DSCR_CMD0_SDMS_RX0, DEV_FLAGS_IN,  4, 8,  0x10600004, 0, 0 },
+	{ AU1300_DSCR_CMD0_SDMS_TX1, DEV_FLAGS_OUT, 8, 8,  0x10601000, 0, 0 },
+	{ AU1300_DSCR_CMD0_SDMS_RX1, DEV_FLAGS_IN,  8, 8,  0x10601004, 0, 0 },
+
+	{ AU1300_DSCR_CMD0_AES_RX, DEV_FLAGS_IN ,   4, 32, 0x10300008, 0, 0 },
+	{ AU1300_DSCR_CMD0_AES_TX, DEV_FLAGS_OUT,   4, 32, 0x10300004, 0, 0 },
+
+	{ AU1300_DSCR_CMD0_PSC0_TX, DEV_FLAGS_OUT,  0, 16, 0x10a0001c, 0, 0 },
+	{ AU1300_DSCR_CMD0_PSC0_RX, DEV_FLAGS_IN,   0, 16, 0x10a0001c, 0, 0 },
+	{ AU1300_DSCR_CMD0_PSC1_TX, DEV_FLAGS_OUT,  0, 16, 0x10a0101c, 0, 0 },
+	{ AU1300_DSCR_CMD0_PSC1_RX, DEV_FLAGS_IN,   0, 16, 0x10a0101c, 0, 0 },
+	{ AU1300_DSCR_CMD0_PSC2_TX, DEV_FLAGS_OUT,  0, 16, 0x10a0201c, 0, 0 },
+	{ AU1300_DSCR_CMD0_PSC2_RX, DEV_FLAGS_IN,   0, 16, 0x10a0201c, 0, 0 },
+	{ AU1300_DSCR_CMD0_PSC3_TX, DEV_FLAGS_OUT,  0, 16, 0x10a0301c, 0, 0 },
+	{ AU1300_DSCR_CMD0_PSC3_RX, DEV_FLAGS_IN,   0, 16, 0x10a0301c, 0, 0 },
+
+	{ AU1300_DSCR_CMD0_LCD, DEV_FLAGS_ANYUSE,   0, 0,  0x00000000, 0, 0 },
+	{ AU1300_DSCR_CMD0_NAND_FLASH, DEV_FLAGS_IN, 0, 0, 0x00000000, 0, 0 },
+
+	{ AU1300_DSCR_CMD0_SDMS_TX2, DEV_FLAGS_OUT, 4, 8,  0x10602000, 0, 0 },
+	{ AU1300_DSCR_CMD0_SDMS_RX2, DEV_FLAGS_IN,  4, 8,  0x10602004, 0, 0 },
+
+	{ AU1300_DSCR_CMD0_CIM_SYNC, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 },
+
+	{ AU1300_DSCR_CMD0_UDMA, DEV_FLAGS_ANYUSE,  0, 32, 0x14001810, 0, 0 },
+
+	{ AU1300_DSCR_CMD0_DMA_REQ0, 0, 0, 0, 0x00000000, 0, 0 },
+	{ AU1300_DSCR_CMD0_DMA_REQ1, 0, 0, 0, 0x00000000, 0, 0 },
+
+	{ DSCR_CMD0_THROTTLE, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 },
+	{ DSCR_CMD0_ALWAYS,   DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 },
+};
+
+/* 32 predefined plus 32 custom */
+#define DBDEV_TAB_SIZE		64
+
+static chan_tab_t *chan_tab_ptr[NUM_DBDMA_CHANS];
+
+static dbdev_tab_t *find_dbdev_id(u32 id)
+{
+	int i;
+	dbdev_tab_t *p;
+	for (i = 0; i < DBDEV_TAB_SIZE; ++i) {
+		p = &dbdev_tab[i];
+		if (p->dev_id == id)
+			return p;
+	}
+	return NULL;
+}
+
+void *au1xxx_ddma_get_nextptr_virt(au1x_ddma_desc_t *dp)
+{
+	return phys_to_virt(DSCR_GET_NXTPTR(dp->dscr_nxtptr));
+}
+EXPORT_SYMBOL(au1xxx_ddma_get_nextptr_virt);
+
+u32 au1xxx_ddma_add_device(dbdev_tab_t *dev)
+{
+	u32 ret = 0;
+	dbdev_tab_t *p;
+	static u16 new_id = 0x1000;
+
+	p = find_dbdev_id(~0);
+	if (NULL != p) {
+		memcpy(p, dev, sizeof(dbdev_tab_t));
+		p->dev_id = DSCR_DEV2CUSTOM_ID(new_id, dev->dev_id);
+		ret = p->dev_id;
+		new_id++;
+#if 0
+		printk(KERN_DEBUG "add_device: id:%x flags:%x padd:%x\n",
+				  p->dev_id, p->dev_flags, p->dev_physaddr);
+#endif
+	}
+
+	return ret;
+}
+EXPORT_SYMBOL(au1xxx_ddma_add_device);
+
+void au1xxx_ddma_del_device(u32 devid)
+{
+	dbdev_tab_t *p = find_dbdev_id(devid);
+
+	if (p != NULL) {
+		memset(p, 0, sizeof(dbdev_tab_t));
+		p->dev_id = ~0;
+	}
+}
+EXPORT_SYMBOL(au1xxx_ddma_del_device);
+
+/* Allocate a channel and return a non-zero descriptor if successful. */
+u32 au1xxx_dbdma_chan_alloc(u32 srcid, u32 destid,
+       void (*callback)(int, void *), void *callparam)
+{
+	unsigned long	flags;
+	u32		used, chan;
+	u32		dcp;
+	int		i;
+	dbdev_tab_t	*stp, *dtp;
+	chan_tab_t	*ctp;
+	au1x_dma_chan_t *cp;
+
+	/*
+	 * We do the initialization on the first channel allocation.
+	 * We have to wait because of the interrupt handler initialization
+	 * which can't be done successfully during board set up.
+	 */
+	if (!dbdma_initialized)
+		return 0;
+
+	stp = find_dbdev_id(srcid);
+	if (stp == NULL)
+		return 0;
+	dtp = find_dbdev_id(destid);
+	if (dtp == NULL)
+		return 0;
+
+	used = 0;
+
+	/* Check to see if we can get both channels. */
+	spin_lock_irqsave(&au1xxx_dbdma_spin_lock, flags);
+	if (!(stp->dev_flags & DEV_FLAGS_INUSE) ||
+	     (stp->dev_flags & DEV_FLAGS_ANYUSE)) {
+		/* Got source */
+		stp->dev_flags |= DEV_FLAGS_INUSE;
+		if (!(dtp->dev_flags & DEV_FLAGS_INUSE) ||
+		     (dtp->dev_flags & DEV_FLAGS_ANYUSE)) {
+			/* Got destination */
+			dtp->dev_flags |= DEV_FLAGS_INUSE;
+		} else {
+			/* Can't get dest.  Release src. */
+			stp->dev_flags &= ~DEV_FLAGS_INUSE;
+			used++;
+		}
+	} else
+		used++;
+	spin_unlock_irqrestore(&au1xxx_dbdma_spin_lock, flags);
+
+	if (used)
+		return 0;
+
+	/* Let's see if we can allocate a channel for it. */
+	ctp = NULL;
+	chan = 0;
+	spin_lock_irqsave(&au1xxx_dbdma_spin_lock, flags);
+	for (i = 0; i < NUM_DBDMA_CHANS; i++)
+		if (chan_tab_ptr[i] == NULL) {
+			/*
+			 * If kmalloc fails, it is caught below same
+			 * as a channel not available.
+			 */
+			ctp = kmalloc(sizeof(chan_tab_t), GFP_ATOMIC);
+			chan_tab_ptr[i] = ctp;
+			break;
+		}
+	spin_unlock_irqrestore(&au1xxx_dbdma_spin_lock, flags);
+
+	if (ctp != NULL) {
+		memset(ctp, 0, sizeof(chan_tab_t));
+		ctp->chan_index = chan = i;
+		dcp = KSEG1ADDR(AU1550_DBDMA_PHYS_ADDR);
+		dcp += (0x0100 * chan);
+		ctp->chan_ptr = (au1x_dma_chan_t *)dcp;
+		cp = (au1x_dma_chan_t *)dcp;
+		ctp->chan_src = stp;
+		ctp->chan_dest = dtp;
+		ctp->chan_callback = callback;
+		ctp->chan_callparam = callparam;
+
+		/* Initialize channel configuration. */
+		i = 0;
+		if (stp->dev_intlevel)
+			i |= DDMA_CFG_SED;
+		if (stp->dev_intpolarity)
+			i |= DDMA_CFG_SP;
+		if (dtp->dev_intlevel)
+			i |= DDMA_CFG_DED;
+		if (dtp->dev_intpolarity)
+			i |= DDMA_CFG_DP;
+		if ((stp->dev_flags & DEV_FLAGS_SYNC) ||
+			(dtp->dev_flags & DEV_FLAGS_SYNC))
+				i |= DDMA_CFG_SYNC;
+		cp->ddma_cfg = i;
+		wmb(); /* drain writebuffer */
+
+		/*
+		 * Return a non-zero value that can be used to find the channel
+		 * information in subsequent operations.
+		 */
+		return (u32)(&chan_tab_ptr[chan]);
+	}
+
+	/* Release devices */
+	stp->dev_flags &= ~DEV_FLAGS_INUSE;
+	dtp->dev_flags &= ~DEV_FLAGS_INUSE;
+
+	return 0;
+}
+EXPORT_SYMBOL(au1xxx_dbdma_chan_alloc);
+
+/*
+ * Set the device width if source or destination is a FIFO.
+ * Should be 8, 16, or 32 bits.
+ */
+u32 au1xxx_dbdma_set_devwidth(u32 chanid, int bits)
+{
+	u32		rv;
+	chan_tab_t	*ctp;
+	dbdev_tab_t	*stp, *dtp;
+
+	ctp = *((chan_tab_t **)chanid);
+	stp = ctp->chan_src;
+	dtp = ctp->chan_dest;
+	rv = 0;
+
+	if (stp->dev_flags & DEV_FLAGS_IN) {	/* Source in fifo */
+		rv = stp->dev_devwidth;
+		stp->dev_devwidth = bits;
+	}
+	if (dtp->dev_flags & DEV_FLAGS_OUT) {	/* Destination out fifo */
+		rv = dtp->dev_devwidth;
+		dtp->dev_devwidth = bits;
+	}
+
+	return rv;
+}
+EXPORT_SYMBOL(au1xxx_dbdma_set_devwidth);
+
+/* Allocate a descriptor ring, initializing as much as possible. */
+u32 au1xxx_dbdma_ring_alloc(u32 chanid, int entries)
+{
+	int			i;
+	u32			desc_base, srcid, destid;
+	u32			cmd0, cmd1, src1, dest1;
+	u32			src0, dest0;
+	chan_tab_t		*ctp;
+	dbdev_tab_t		*stp, *dtp;
+	au1x_ddma_desc_t	*dp;
+
+	/*
+	 * I guess we could check this to be within the
+	 * range of the table......
+	 */
+	ctp = *((chan_tab_t **)chanid);
+	stp = ctp->chan_src;
+	dtp = ctp->chan_dest;
+
+	/*
+	 * The descriptors must be 32-byte aligned.  There is a
+	 * possibility the allocation will give us such an address,
+	 * and if we try that first we are likely to not waste larger
+	 * slabs of memory.
+	 */
+	desc_base = (u32)kmalloc_array(entries, sizeof(au1x_ddma_desc_t),
+				       GFP_KERNEL|GFP_DMA);
+	if (desc_base == 0)
+		return 0;
+
+	if (desc_base & 0x1f) {
+		/*
+		 * Lost....do it again, allocate extra, and round
+		 * the address base.
+		 */
+		kfree((const void *)desc_base);
+		i = entries * sizeof(au1x_ddma_desc_t);
+		i += (sizeof(au1x_ddma_desc_t) - 1);
+		desc_base = (u32)kmalloc(i, GFP_KERNEL|GFP_DMA);
+		if (desc_base == 0)
+			return 0;
+
+		ctp->cdb_membase = desc_base;
+		desc_base = ALIGN_ADDR(desc_base, sizeof(au1x_ddma_desc_t));
+	} else
+		ctp->cdb_membase = desc_base;
+
+	dp = (au1x_ddma_desc_t *)desc_base;
+
+	/* Keep track of the base descriptor. */
+	ctp->chan_desc_base = dp;
+
+	/* Initialize the rings with as much information as we know. */
+	srcid = stp->dev_id;
+	destid = dtp->dev_id;
+
+	cmd0 = cmd1 = src1 = dest1 = 0;
+	src0 = dest0 = 0;
+
+	cmd0 |= DSCR_CMD0_SID(srcid);
+	cmd0 |= DSCR_CMD0_DID(destid);
+	cmd0 |= DSCR_CMD0_IE | DSCR_CMD0_CV;
+	cmd0 |= DSCR_CMD0_ST(DSCR_CMD0_ST_NOCHANGE);
+
+	/* Is it mem to mem transfer? */
+	if (((DSCR_CUSTOM2DEV_ID(srcid) == DSCR_CMD0_THROTTLE) ||
+	     (DSCR_CUSTOM2DEV_ID(srcid) == DSCR_CMD0_ALWAYS)) &&
+	    ((DSCR_CUSTOM2DEV_ID(destid) == DSCR_CMD0_THROTTLE) ||
+	     (DSCR_CUSTOM2DEV_ID(destid) == DSCR_CMD0_ALWAYS)))
+		cmd0 |= DSCR_CMD0_MEM;
+
+	switch (stp->dev_devwidth) {
+	case 8:
+		cmd0 |= DSCR_CMD0_SW(DSCR_CMD0_BYTE);
+		break;
+	case 16:
+		cmd0 |= DSCR_CMD0_SW(DSCR_CMD0_HALFWORD);
+		break;
+	case 32:
+	default:
+		cmd0 |= DSCR_CMD0_SW(DSCR_CMD0_WORD);
+		break;
+	}
+
+	switch (dtp->dev_devwidth) {
+	case 8:
+		cmd0 |= DSCR_CMD0_DW(DSCR_CMD0_BYTE);
+		break;
+	case 16:
+		cmd0 |= DSCR_CMD0_DW(DSCR_CMD0_HALFWORD);
+		break;
+	case 32:
+	default:
+		cmd0 |= DSCR_CMD0_DW(DSCR_CMD0_WORD);
+		break;
+	}
+
+	/*
+	 * If the device is marked as an in/out FIFO, ensure it is
+	 * set non-coherent.
+	 */
+	if (stp->dev_flags & DEV_FLAGS_IN)
+		cmd0 |= DSCR_CMD0_SN;		/* Source in FIFO */
+	if (dtp->dev_flags & DEV_FLAGS_OUT)
+		cmd0 |= DSCR_CMD0_DN;		/* Destination out FIFO */
+
+	/*
+	 * Set up source1.  For now, assume no stride and increment.
+	 * A channel attribute update can change this later.
+	 */
+	switch (stp->dev_tsize) {
+	case 1:
+		src1 |= DSCR_SRC1_STS(DSCR_xTS_SIZE1);
+		break;
+	case 2:
+		src1 |= DSCR_SRC1_STS(DSCR_xTS_SIZE2);
+		break;
+	case 4:
+		src1 |= DSCR_SRC1_STS(DSCR_xTS_SIZE4);
+		break;
+	case 8:
+	default:
+		src1 |= DSCR_SRC1_STS(DSCR_xTS_SIZE8);
+		break;
+	}
+
+	/* If source input is FIFO, set static address. */
+	if (stp->dev_flags & DEV_FLAGS_IN) {
+		if (stp->dev_flags & DEV_FLAGS_BURSTABLE)
+			src1 |= DSCR_SRC1_SAM(DSCR_xAM_BURST);
+		else
+			src1 |= DSCR_SRC1_SAM(DSCR_xAM_STATIC);
+	}
+
+	if (stp->dev_physaddr)
+		src0 = stp->dev_physaddr;
+
+	/*
+	 * Set up dest1.  For now, assume no stride and increment.
+	 * A channel attribute update can change this later.
+	 */
+	switch (dtp->dev_tsize) {
+	case 1:
+		dest1 |= DSCR_DEST1_DTS(DSCR_xTS_SIZE1);
+		break;
+	case 2:
+		dest1 |= DSCR_DEST1_DTS(DSCR_xTS_SIZE2);
+		break;
+	case 4:
+		dest1 |= DSCR_DEST1_DTS(DSCR_xTS_SIZE4);
+		break;
+	case 8:
+	default:
+		dest1 |= DSCR_DEST1_DTS(DSCR_xTS_SIZE8);
+		break;
+	}
+
+	/* If destination output is FIFO, set static address. */
+	if (dtp->dev_flags & DEV_FLAGS_OUT) {
+		if (dtp->dev_flags & DEV_FLAGS_BURSTABLE)
+			dest1 |= DSCR_DEST1_DAM(DSCR_xAM_BURST);
+		else
+			dest1 |= DSCR_DEST1_DAM(DSCR_xAM_STATIC);
+	}
+
+	if (dtp->dev_physaddr)
+		dest0 = dtp->dev_physaddr;
+
+#if 0
+		printk(KERN_DEBUG "did:%x sid:%x cmd0:%x cmd1:%x source0:%x "
+				  "source1:%x dest0:%x dest1:%x\n",
+				  dtp->dev_id, stp->dev_id, cmd0, cmd1, src0,
+				  src1, dest0, dest1);
+#endif
+	for (i = 0; i < entries; i++) {
+		dp->dscr_cmd0 = cmd0;
+		dp->dscr_cmd1 = cmd1;
+		dp->dscr_source0 = src0;
+		dp->dscr_source1 = src1;
+		dp->dscr_dest0 = dest0;
+		dp->dscr_dest1 = dest1;
+		dp->dscr_stat = 0;
+		dp->sw_context = 0;
+		dp->sw_status = 0;
+		dp->dscr_nxtptr = DSCR_NXTPTR(virt_to_phys(dp + 1));
+		dp++;
+	}
+
+	/* Make last descriptor point to the first. */
+	dp--;
+	dp->dscr_nxtptr = DSCR_NXTPTR(virt_to_phys(ctp->chan_desc_base));
+	ctp->get_ptr = ctp->put_ptr = ctp->cur_ptr = ctp->chan_desc_base;
+
+	return (u32)ctp->chan_desc_base;
+}
+EXPORT_SYMBOL(au1xxx_dbdma_ring_alloc);
+
+/*
+ * Put a source buffer into the DMA ring.
+ * This updates the source pointer and byte count.  Normally used
+ * for memory to fifo transfers.
+ */
+u32 au1xxx_dbdma_put_source(u32 chanid, dma_addr_t buf, int nbytes, u32 flags)
+{
+	chan_tab_t		*ctp;
+	au1x_ddma_desc_t	*dp;
+
+	/*
+	 * I guess we could check this to be within the
+	 * range of the table......
+	 */
+	ctp = *(chan_tab_t **)chanid;
+
+	/*
+	 * We should have multiple callers for a particular channel,
+	 * an interrupt doesn't affect this pointer nor the descriptor,
+	 * so no locking should be needed.
+	 */
+	dp = ctp->put_ptr;
+
+	/*
+	 * If the descriptor is valid, we are way ahead of the DMA
+	 * engine, so just return an error condition.
+	 */
+	if (dp->dscr_cmd0 & DSCR_CMD0_V)
+		return 0;
+
+	/* Load up buffer address and byte count. */
+	dp->dscr_source0 = buf & ~0UL;
+	dp->dscr_cmd1 = nbytes;
+	/* Check flags */
+	if (flags & DDMA_FLAGS_IE)
+		dp->dscr_cmd0 |= DSCR_CMD0_IE;
+	if (flags & DDMA_FLAGS_NOIE)
+		dp->dscr_cmd0 &= ~DSCR_CMD0_IE;
+
+	/*
+	 * There is an erratum on certain Au1200/Au1550 revisions that could
+	 * result in "stale" data being DMA'ed. It has to do with the snoop
+	 * logic on the cache eviction buffer.  dma_default_coherent is set
+	 * to false on these parts.
+	 */
+	if (!dma_default_coherent)
+		dma_cache_wback_inv(KSEG0ADDR(buf), nbytes);
+	dp->dscr_cmd0 |= DSCR_CMD0_V;	/* Let it rip */
+	wmb(); /* drain writebuffer */
+	dma_cache_wback_inv((unsigned long)dp, sizeof(*dp));
+	ctp->chan_ptr->ddma_dbell = 0;
+	wmb(); /* force doorbell write out to dma engine */
+
+	/* Get next descriptor pointer. */
+	ctp->put_ptr = phys_to_virt(DSCR_GET_NXTPTR(dp->dscr_nxtptr));
+
+	/* Return something non-zero. */
+	return nbytes;
+}
+EXPORT_SYMBOL(au1xxx_dbdma_put_source);
+
+/* Put a destination buffer into the DMA ring.
+ * This updates the destination pointer and byte count.  Normally used
+ * to place an empty buffer into the ring for fifo to memory transfers.
+ */
+u32 au1xxx_dbdma_put_dest(u32 chanid, dma_addr_t buf, int nbytes, u32 flags)
+{
+	chan_tab_t		*ctp;
+	au1x_ddma_desc_t	*dp;
+
+	/* I guess we could check this to be within the
+	 * range of the table......
+	 */
+	ctp = *((chan_tab_t **)chanid);
+
+	/* We should have multiple callers for a particular channel,
+	 * an interrupt doesn't affect this pointer nor the descriptor,
+	 * so no locking should be needed.
+	 */
+	dp = ctp->put_ptr;
+
+	/* If the descriptor is valid, we are way ahead of the DMA
+	 * engine, so just return an error condition.
+	 */
+	if (dp->dscr_cmd0 & DSCR_CMD0_V)
+		return 0;
+
+	/* Load up buffer address and byte count */
+
+	/* Check flags  */
+	if (flags & DDMA_FLAGS_IE)
+		dp->dscr_cmd0 |= DSCR_CMD0_IE;
+	if (flags & DDMA_FLAGS_NOIE)
+		dp->dscr_cmd0 &= ~DSCR_CMD0_IE;
+
+	dp->dscr_dest0 = buf & ~0UL;
+	dp->dscr_cmd1 = nbytes;
+#if 0
+	printk(KERN_DEBUG "cmd0:%x cmd1:%x source0:%x source1:%x dest0:%x dest1:%x\n",
+			  dp->dscr_cmd0, dp->dscr_cmd1, dp->dscr_source0,
+			  dp->dscr_source1, dp->dscr_dest0, dp->dscr_dest1);
+#endif
+	/*
+	 * There is an erratum on certain Au1200/Au1550 revisions that could
+	 * result in "stale" data being DMA'ed. It has to do with the snoop
+	 * logic on the cache eviction buffer.  dma_default_coherent is set
+	 * to false on these parts.
+	 */
+	if (!dma_default_coherent)
+		dma_cache_inv(KSEG0ADDR(buf), nbytes);
+	dp->dscr_cmd0 |= DSCR_CMD0_V;	/* Let it rip */
+	wmb(); /* drain writebuffer */
+	dma_cache_wback_inv((unsigned long)dp, sizeof(*dp));
+	ctp->chan_ptr->ddma_dbell = 0;
+	wmb(); /* force doorbell write out to dma engine */
+
+	/* Get next descriptor pointer. */
+	ctp->put_ptr = phys_to_virt(DSCR_GET_NXTPTR(dp->dscr_nxtptr));
+
+	/* Return something non-zero. */
+	return nbytes;
+}
+EXPORT_SYMBOL(au1xxx_dbdma_put_dest);
+
+/*
+ * Get a destination buffer into the DMA ring.
+ * Normally used to get a full buffer from the ring during fifo
+ * to memory transfers.  This does not set the valid bit, you will
+ * have to put another destination buffer to keep the DMA going.
+ */
+u32 au1xxx_dbdma_get_dest(u32 chanid, void **buf, int *nbytes)
+{
+	chan_tab_t		*ctp;
+	au1x_ddma_desc_t	*dp;
+	u32			rv;
+
+	/*
+	 * I guess we could check this to be within the
+	 * range of the table......
+	 */
+	ctp = *((chan_tab_t **)chanid);
+
+	/*
+	 * We should have multiple callers for a particular channel,
+	 * an interrupt doesn't affect this pointer nor the descriptor,
+	 * so no locking should be needed.
+	 */
+	dp = ctp->get_ptr;
+
+	/*
+	 * If the descriptor is valid, we are way ahead of the DMA
+	 * engine, so just return an error condition.
+	 */
+	if (dp->dscr_cmd0 & DSCR_CMD0_V)
+		return 0;
+
+	/* Return buffer address and byte count. */
+	*buf = (void *)(phys_to_virt(dp->dscr_dest0));
+	*nbytes = dp->dscr_cmd1;
+	rv = dp->dscr_stat;
+
+	/* Get next descriptor pointer. */
+	ctp->get_ptr = phys_to_virt(DSCR_GET_NXTPTR(dp->dscr_nxtptr));
+
+	/* Return something non-zero. */
+	return rv;
+}
+EXPORT_SYMBOL_GPL(au1xxx_dbdma_get_dest);
+
+void au1xxx_dbdma_stop(u32 chanid)
+{
+	chan_tab_t	*ctp;
+	au1x_dma_chan_t *cp;
+	int halt_timeout = 0;
+
+	ctp = *((chan_tab_t **)chanid);
+
+	cp = ctp->chan_ptr;
+	cp->ddma_cfg &= ~DDMA_CFG_EN;	/* Disable channel */
+	wmb(); /* drain writebuffer */
+	while (!(cp->ddma_stat & DDMA_STAT_H)) {
+		udelay(1);
+		halt_timeout++;
+		if (halt_timeout > 100) {
+			printk(KERN_WARNING "warning: DMA channel won't halt\n");
+			break;
+		}
+	}
+	/* clear current desc valid and doorbell */
+	cp->ddma_stat |= (DDMA_STAT_DB | DDMA_STAT_V);
+	wmb(); /* drain writebuffer */
+}
+EXPORT_SYMBOL(au1xxx_dbdma_stop);
+
+/*
+ * Start using the current descriptor pointer.  If the DBDMA encounters
+ * a non-valid descriptor, it will stop.  In this case, we can just
+ * continue by adding a buffer to the list and starting again.
+ */
+void au1xxx_dbdma_start(u32 chanid)
+{
+	chan_tab_t	*ctp;
+	au1x_dma_chan_t *cp;
+
+	ctp = *((chan_tab_t **)chanid);
+	cp = ctp->chan_ptr;
+	cp->ddma_desptr = virt_to_phys(ctp->cur_ptr);
+	cp->ddma_cfg |= DDMA_CFG_EN;	/* Enable channel */
+	wmb(); /* drain writebuffer */
+	cp->ddma_dbell = 0;
+	wmb(); /* drain writebuffer */
+}
+EXPORT_SYMBOL(au1xxx_dbdma_start);
+
+void au1xxx_dbdma_reset(u32 chanid)
+{
+	chan_tab_t		*ctp;
+	au1x_ddma_desc_t	*dp;
+
+	au1xxx_dbdma_stop(chanid);
+
+	ctp = *((chan_tab_t **)chanid);
+	ctp->get_ptr = ctp->put_ptr = ctp->cur_ptr = ctp->chan_desc_base;
+
+	/* Run through the descriptors and reset the valid indicator. */
+	dp = ctp->chan_desc_base;
+
+	do {
+		dp->dscr_cmd0 &= ~DSCR_CMD0_V;
+		/*
+		 * Reset our software status -- this is used to determine
+		 * if a descriptor is in use by upper level software. Since
+		 * posting can reset 'V' bit.
+		 */
+		dp->sw_status = 0;
+		dp = phys_to_virt(DSCR_GET_NXTPTR(dp->dscr_nxtptr));
+	} while (dp != ctp->chan_desc_base);
+}
+EXPORT_SYMBOL(au1xxx_dbdma_reset);
+
+u32 au1xxx_get_dma_residue(u32 chanid)
+{
+	chan_tab_t	*ctp;
+	au1x_dma_chan_t *cp;
+	u32		rv;
+
+	ctp = *((chan_tab_t **)chanid);
+	cp = ctp->chan_ptr;
+
+	/* This is only valid if the channel is stopped. */
+	rv = cp->ddma_bytecnt;
+	wmb(); /* drain writebuffer */
+
+	return rv;
+}
+EXPORT_SYMBOL_GPL(au1xxx_get_dma_residue);
+
+void au1xxx_dbdma_chan_free(u32 chanid)
+{
+	chan_tab_t	*ctp;
+	dbdev_tab_t	*stp, *dtp;
+
+	ctp = *((chan_tab_t **)chanid);
+	stp = ctp->chan_src;
+	dtp = ctp->chan_dest;
+
+	au1xxx_dbdma_stop(chanid);
+
+	kfree((void *)ctp->cdb_membase);
+
+	stp->dev_flags &= ~DEV_FLAGS_INUSE;
+	dtp->dev_flags &= ~DEV_FLAGS_INUSE;
+	chan_tab_ptr[ctp->chan_index] = NULL;
+
+	kfree(ctp);
+}
+EXPORT_SYMBOL(au1xxx_dbdma_chan_free);
+
+static irqreturn_t dbdma_interrupt(int irq, void *dev_id)
+{
+	u32 intstat;
+	u32 chan_index;
+	chan_tab_t		*ctp;
+	au1x_ddma_desc_t	*dp;
+	au1x_dma_chan_t *cp;
+
+	intstat = dbdma_gptr->ddma_intstat;
+	wmb(); /* drain writebuffer */
+	chan_index = __ffs(intstat);
+
+	ctp = chan_tab_ptr[chan_index];
+	cp = ctp->chan_ptr;
+	dp = ctp->cur_ptr;
+
+	/* Reset interrupt. */
+	cp->ddma_irq = 0;
+	wmb(); /* drain writebuffer */
+
+	if (ctp->chan_callback)
+		ctp->chan_callback(irq, ctp->chan_callparam);
+
+	ctp->cur_ptr = phys_to_virt(DSCR_GET_NXTPTR(dp->dscr_nxtptr));
+	return IRQ_RETVAL(1);
+}
+
+void au1xxx_dbdma_dump(u32 chanid)
+{
+	chan_tab_t	 *ctp;
+	au1x_ddma_desc_t *dp;
+	dbdev_tab_t	 *stp, *dtp;
+	au1x_dma_chan_t	 *cp;
+	u32 i		 = 0;
+
+	ctp = *((chan_tab_t **)chanid);
+	stp = ctp->chan_src;
+	dtp = ctp->chan_dest;
+	cp = ctp->chan_ptr;
+
+	printk(KERN_DEBUG "Chan %x, stp %x (dev %d)  dtp %x (dev %d)\n",
+			  (u32)ctp, (u32)stp, stp - dbdev_tab, (u32)dtp,
+			  dtp - dbdev_tab);
+	printk(KERN_DEBUG "desc base %x, get %x, put %x, cur %x\n",
+			  (u32)(ctp->chan_desc_base), (u32)(ctp->get_ptr),
+			  (u32)(ctp->put_ptr), (u32)(ctp->cur_ptr));
+
+	printk(KERN_DEBUG "dbdma chan %x\n", (u32)cp);
+	printk(KERN_DEBUG "cfg %08x, desptr %08x, statptr %08x\n",
+			  cp->ddma_cfg, cp->ddma_desptr, cp->ddma_statptr);
+	printk(KERN_DEBUG "dbell %08x, irq %08x, stat %08x, bytecnt %08x\n",
+			  cp->ddma_dbell, cp->ddma_irq, cp->ddma_stat,
+			  cp->ddma_bytecnt);
+
+	/* Run through the descriptors */
+	dp = ctp->chan_desc_base;
+
+	do {
+		printk(KERN_DEBUG "Dp[%d]= %08x, cmd0 %08x, cmd1 %08x\n",
+				  i++, (u32)dp, dp->dscr_cmd0, dp->dscr_cmd1);
+		printk(KERN_DEBUG "src0 %08x, src1 %08x, dest0 %08x, dest1 %08x\n",
+				  dp->dscr_source0, dp->dscr_source1,
+				  dp->dscr_dest0, dp->dscr_dest1);
+		printk(KERN_DEBUG "stat %08x, nxtptr %08x\n",
+				  dp->dscr_stat, dp->dscr_nxtptr);
+		dp = phys_to_virt(DSCR_GET_NXTPTR(dp->dscr_nxtptr));
+	} while (dp != ctp->chan_desc_base);
+}
+
+/* Put a descriptor into the DMA ring.
+ * This updates the source/destination pointers and byte count.
+ */
+u32 au1xxx_dbdma_put_dscr(u32 chanid, au1x_ddma_desc_t *dscr)
+{
+	chan_tab_t *ctp;
+	au1x_ddma_desc_t *dp;
+	u32 nbytes = 0;
+
+	/*
+	 * I guess we could check this to be within the
+	 * range of the table......
+	 */
+	ctp = *((chan_tab_t **)chanid);
+
+	/*
+	 * We should have multiple callers for a particular channel,
+	 * an interrupt doesn't affect this pointer nor the descriptor,
+	 * so no locking should be needed.
+	 */
+	dp = ctp->put_ptr;
+
+	/*
+	 * If the descriptor is valid, we are way ahead of the DMA
+	 * engine, so just return an error condition.
+	 */
+	if (dp->dscr_cmd0 & DSCR_CMD0_V)
+		return 0;
+
+	/* Load up buffer addresses and byte count. */
+	dp->dscr_dest0 = dscr->dscr_dest0;
+	dp->dscr_source0 = dscr->dscr_source0;
+	dp->dscr_dest1 = dscr->dscr_dest1;
+	dp->dscr_source1 = dscr->dscr_source1;
+	dp->dscr_cmd1 = dscr->dscr_cmd1;
+	nbytes = dscr->dscr_cmd1;
+	/* Allow the caller to specify if an interrupt is generated */
+	dp->dscr_cmd0 &= ~DSCR_CMD0_IE;
+	dp->dscr_cmd0 |= dscr->dscr_cmd0 | DSCR_CMD0_V;
+	ctp->chan_ptr->ddma_dbell = 0;
+
+	/* Get next descriptor pointer. */
+	ctp->put_ptr = phys_to_virt(DSCR_GET_NXTPTR(dp->dscr_nxtptr));
+
+	/* Return something non-zero. */
+	return nbytes;
+}
+
+
+static unsigned long alchemy_dbdma_pm_data[NUM_DBDMA_CHANS + 1][6];
+
+static int alchemy_dbdma_suspend(void)
+{
+	int i;
+	void __iomem *addr;
+
+	addr = (void __iomem *)KSEG1ADDR(AU1550_DBDMA_CONF_PHYS_ADDR);
+	alchemy_dbdma_pm_data[0][0] = __raw_readl(addr + 0x00);
+	alchemy_dbdma_pm_data[0][1] = __raw_readl(addr + 0x04);
+	alchemy_dbdma_pm_data[0][2] = __raw_readl(addr + 0x08);
+	alchemy_dbdma_pm_data[0][3] = __raw_readl(addr + 0x0c);
+
+	/* save channel configurations */
+	addr = (void __iomem *)KSEG1ADDR(AU1550_DBDMA_PHYS_ADDR);
+	for (i = 1; i <= NUM_DBDMA_CHANS; i++) {
+		alchemy_dbdma_pm_data[i][0] = __raw_readl(addr + 0x00);
+		alchemy_dbdma_pm_data[i][1] = __raw_readl(addr + 0x04);
+		alchemy_dbdma_pm_data[i][2] = __raw_readl(addr + 0x08);
+		alchemy_dbdma_pm_data[i][3] = __raw_readl(addr + 0x0c);
+		alchemy_dbdma_pm_data[i][4] = __raw_readl(addr + 0x10);
+		alchemy_dbdma_pm_data[i][5] = __raw_readl(addr + 0x14);
+
+		/* halt channel */
+		__raw_writel(alchemy_dbdma_pm_data[i][0] & ~1, addr + 0x00);
+		wmb();
+		while (!(__raw_readl(addr + 0x14) & 1))
+			wmb();
+
+		addr += 0x100;	/* next channel base */
+	}
+	/* disable channel interrupts */
+	addr = (void __iomem *)KSEG1ADDR(AU1550_DBDMA_CONF_PHYS_ADDR);
+	__raw_writel(0, addr + 0x0c);
+	wmb();
+
+	return 0;
+}
+
+static void alchemy_dbdma_resume(void)
+{
+	int i;
+	void __iomem *addr;
+
+	addr = (void __iomem *)KSEG1ADDR(AU1550_DBDMA_CONF_PHYS_ADDR);
+	__raw_writel(alchemy_dbdma_pm_data[0][0], addr + 0x00);
+	__raw_writel(alchemy_dbdma_pm_data[0][1], addr + 0x04);
+	__raw_writel(alchemy_dbdma_pm_data[0][2], addr + 0x08);
+	__raw_writel(alchemy_dbdma_pm_data[0][3], addr + 0x0c);
+
+	/* restore channel configurations */
+	addr = (void __iomem *)KSEG1ADDR(AU1550_DBDMA_PHYS_ADDR);
+	for (i = 1; i <= NUM_DBDMA_CHANS; i++) {
+		__raw_writel(alchemy_dbdma_pm_data[i][0], addr + 0x00);
+		__raw_writel(alchemy_dbdma_pm_data[i][1], addr + 0x04);
+		__raw_writel(alchemy_dbdma_pm_data[i][2], addr + 0x08);
+		__raw_writel(alchemy_dbdma_pm_data[i][3], addr + 0x0c);
+		__raw_writel(alchemy_dbdma_pm_data[i][4], addr + 0x10);
+		__raw_writel(alchemy_dbdma_pm_data[i][5], addr + 0x14);
+		wmb();
+		addr += 0x100;	/* next channel base */
+	}
+}
+
+static struct syscore_ops alchemy_dbdma_syscore_ops = {
+	.suspend	= alchemy_dbdma_suspend,
+	.resume		= alchemy_dbdma_resume,
+};
+
+static int __init dbdma_setup(unsigned int irq, dbdev_tab_t *idtable)
+{
+	int ret;
+
+	dbdev_tab = kcalloc(DBDEV_TAB_SIZE, sizeof(dbdev_tab_t), GFP_KERNEL);
+	if (!dbdev_tab)
+		return -ENOMEM;
+
+	memcpy(dbdev_tab, idtable, 32 * sizeof(dbdev_tab_t));
+	for (ret = 32; ret < DBDEV_TAB_SIZE; ret++)
+		dbdev_tab[ret].dev_id = ~0;
+
+	dbdma_gptr->ddma_config = 0;
+	dbdma_gptr->ddma_throttle = 0;
+	dbdma_gptr->ddma_inten = 0xffff;
+	wmb(); /* drain writebuffer */
+
+	ret = request_irq(irq, dbdma_interrupt, 0, "dbdma", (void *)dbdma_gptr);
+	if (ret)
+		printk(KERN_ERR "Cannot grab DBDMA interrupt!\n");
+	else {
+		dbdma_initialized = 1;
+		register_syscore_ops(&alchemy_dbdma_syscore_ops);
+	}
+
+	return ret;
+}
+
+static int __init alchemy_dbdma_init(void)
+{
+	switch (alchemy_get_cputype()) {
+	case ALCHEMY_CPU_AU1550:
+		return dbdma_setup(AU1550_DDMA_INT, au1550_dbdev_tab);
+	case ALCHEMY_CPU_AU1200:
+		return dbdma_setup(AU1200_DDMA_INT, au1200_dbdev_tab);
+	case ALCHEMY_CPU_AU1300:
+		return dbdma_setup(AU1300_DDMA_INT, au1300_dbdev_tab);
+	}
+	return 0;
+}
+subsys_initcall(alchemy_dbdma_init);
diff --git a/arch/mips/alchemy/common/dma.c b/arch/mips/alchemy/common/dma.c
new file mode 100644
index 000000000..973049b5b
--- /dev/null
+++ b/arch/mips/alchemy/common/dma.c
@@ -0,0 +1,265 @@
+/*
+ *
+ * BRIEF MODULE DESCRIPTION
+ *      A DMA channel allocator for Au1x00. API is modeled loosely off of
+ *      linux/kernel/dma.c.
+ *
+ * Copyright 2000, 2008 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc. <source@mvista.com>
+ * Copyright (C) 2005 Ralf Baechle (ralf@linux-mips.org)
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ */
+
+#include <linux/init.h>
+#include <linux/export.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/spinlock.h>
+#include <linux/interrupt.h>
+
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1000_dma.h>
+
+/*
+ * A note on resource allocation:
+ *
+ * All drivers needing DMA channels, should allocate and release them
+ * through the public routines `request_dma()' and `free_dma()'.
+ *
+ * In order to avoid problems, all processes should allocate resources in
+ * the same sequence and release them in the reverse order.
+ *
+ * So, when allocating DMAs and IRQs, first allocate the DMA, then the IRQ.
+ * When releasing them, first release the IRQ, then release the DMA. The
+ * main reason for this order is that, if you are requesting the DMA buffer
+ * done interrupt, you won't know the irq number until the DMA channel is
+ * returned from request_dma.
+ */
+
+/* DMA Channel register block spacing */
+#define DMA_CHANNEL_LEN		0x00000100
+
+DEFINE_SPINLOCK(au1000_dma_spin_lock);
+
+struct dma_chan au1000_dma_table[NUM_AU1000_DMA_CHANNELS] = {
+      {.dev_id = -1,},
+      {.dev_id = -1,},
+      {.dev_id = -1,},
+      {.dev_id = -1,},
+      {.dev_id = -1,},
+      {.dev_id = -1,},
+      {.dev_id = -1,},
+      {.dev_id = -1,}
+};
+EXPORT_SYMBOL(au1000_dma_table);
+
+/* Device FIFO addresses and default DMA modes */
+static const struct dma_dev {
+	unsigned int fifo_addr;
+	unsigned int dma_mode;
+} dma_dev_table[DMA_NUM_DEV] = {
+	{ AU1000_UART0_PHYS_ADDR + 0x04, DMA_DW8 },		/* UART0_TX */
+	{ AU1000_UART0_PHYS_ADDR + 0x00, DMA_DW8 | DMA_DR },	/* UART0_RX */
+	{ 0, 0 },	/* DMA_REQ0 */
+	{ 0, 0 },	/* DMA_REQ1 */
+	{ AU1000_AC97_PHYS_ADDR + 0x08, DMA_DW16 },		/* AC97 TX c */
+	{ AU1000_AC97_PHYS_ADDR + 0x08, DMA_DW16 | DMA_DR },	/* AC97 RX c */
+	{ AU1000_UART3_PHYS_ADDR + 0x04, DMA_DW8 | DMA_NC },	/* UART3_TX */
+	{ AU1000_UART3_PHYS_ADDR + 0x00, DMA_DW8 | DMA_NC | DMA_DR }, /* UART3_RX */
+	{ AU1000_USB_UDC_PHYS_ADDR + 0x00, DMA_DW8 | DMA_NC | DMA_DR }, /* EP0RD */
+	{ AU1000_USB_UDC_PHYS_ADDR + 0x04, DMA_DW8 | DMA_NC }, /* EP0WR */
+	{ AU1000_USB_UDC_PHYS_ADDR + 0x08, DMA_DW8 | DMA_NC }, /* EP2WR */
+	{ AU1000_USB_UDC_PHYS_ADDR + 0x0c, DMA_DW8 | DMA_NC }, /* EP3WR */
+	{ AU1000_USB_UDC_PHYS_ADDR + 0x10, DMA_DW8 | DMA_NC | DMA_DR }, /* EP4RD */
+	{ AU1000_USB_UDC_PHYS_ADDR + 0x14, DMA_DW8 | DMA_NC | DMA_DR }, /* EP5RD */
+	/* on Au1500, these 2 are DMA_REQ2/3 (GPIO208/209) instead! */
+	{ AU1000_I2S_PHYS_ADDR + 0x00, DMA_DW32 | DMA_NC},	/* I2S TX */
+	{ AU1000_I2S_PHYS_ADDR + 0x00, DMA_DW32 | DMA_NC | DMA_DR}, /* I2S RX */
+};
+
+int au1000_dma_read_proc(char *buf, char **start, off_t fpos,
+			 int length, int *eof, void *data)
+{
+	int i, len = 0;
+	struct dma_chan *chan;
+
+	for (i = 0; i < NUM_AU1000_DMA_CHANNELS; i++) {
+		chan = get_dma_chan(i);
+		if (chan != NULL)
+			len += sprintf(buf + len, "%2d: %s\n",
+				       i, chan->dev_str);
+	}
+
+	if (fpos >= len) {
+		*start = buf;
+		*eof = 1;
+		return 0;
+	}
+	*start = buf + fpos;
+	len -= fpos;
+	if (len > length)
+		return length;
+	*eof = 1;
+	return len;
+}
+
+/* Device FIFO addresses and default DMA modes - 2nd bank */
+static const struct dma_dev dma_dev_table_bank2[DMA_NUM_DEV_BANK2] = {
+	{ AU1100_SD0_PHYS_ADDR + 0x00, DMA_DS | DMA_DW8 },		/* coherent */
+	{ AU1100_SD0_PHYS_ADDR + 0x04, DMA_DS | DMA_DW8 | DMA_DR },	/* coherent */
+	{ AU1100_SD1_PHYS_ADDR + 0x00, DMA_DS | DMA_DW8 },		/* coherent */
+	{ AU1100_SD1_PHYS_ADDR + 0x04, DMA_DS | DMA_DW8 | DMA_DR }	/* coherent */
+};
+
+void dump_au1000_dma_channel(unsigned int dmanr)
+{
+	struct dma_chan *chan;
+
+	if (dmanr >= NUM_AU1000_DMA_CHANNELS)
+		return;
+	chan = &au1000_dma_table[dmanr];
+
+	printk(KERN_INFO "Au1000 DMA%d Register Dump:\n", dmanr);
+	printk(KERN_INFO "  mode = 0x%08x\n",
+	       __raw_readl(chan->io + DMA_MODE_SET));
+	printk(KERN_INFO "  addr = 0x%08x\n",
+	       __raw_readl(chan->io + DMA_PERIPHERAL_ADDR));
+	printk(KERN_INFO "  start0 = 0x%08x\n",
+	       __raw_readl(chan->io + DMA_BUFFER0_START));
+	printk(KERN_INFO "  start1 = 0x%08x\n",
+	       __raw_readl(chan->io + DMA_BUFFER1_START));
+	printk(KERN_INFO "  count0 = 0x%08x\n",
+	       __raw_readl(chan->io + DMA_BUFFER0_COUNT));
+	printk(KERN_INFO "  count1 = 0x%08x\n",
+	       __raw_readl(chan->io + DMA_BUFFER1_COUNT));
+}
+
+/*
+ * Finds a free channel, and binds the requested device to it.
+ * Returns the allocated channel number, or negative on error.
+ * Requests the DMA done IRQ if irqhandler != NULL.
+ */
+int request_au1000_dma(int dev_id, const char *dev_str,
+		       irq_handler_t irqhandler,
+		       unsigned long irqflags,
+		       void *irq_dev_id)
+{
+	struct dma_chan *chan;
+	const struct dma_dev *dev;
+	int i, ret;
+
+	if (alchemy_get_cputype() == ALCHEMY_CPU_AU1100) {
+		if (dev_id < 0 || dev_id >= (DMA_NUM_DEV + DMA_NUM_DEV_BANK2))
+			return -EINVAL;
+	} else {
+		if (dev_id < 0 || dev_id >= DMA_NUM_DEV)
+			return -EINVAL;
+	}
+
+	for (i = 0; i < NUM_AU1000_DMA_CHANNELS; i++)
+		if (au1000_dma_table[i].dev_id < 0)
+			break;
+
+	if (i == NUM_AU1000_DMA_CHANNELS)
+		return -ENODEV;
+
+	chan = &au1000_dma_table[i];
+
+	if (dev_id >= DMA_NUM_DEV) {
+		dev_id -= DMA_NUM_DEV;
+		dev = &dma_dev_table_bank2[dev_id];
+	} else
+		dev = &dma_dev_table[dev_id];
+
+	if (irqhandler) {
+		chan->irq_dev = irq_dev_id;
+		ret = request_irq(chan->irq, irqhandler, irqflags, dev_str,
+				  chan->irq_dev);
+		if (ret) {
+			chan->irq_dev = NULL;
+			return ret;
+		}
+	} else {
+		chan->irq_dev = NULL;
+	}
+
+	/* fill it in */
+	chan->io = (void __iomem *)(KSEG1ADDR(AU1000_DMA_PHYS_ADDR) +
+			i * DMA_CHANNEL_LEN);
+	chan->dev_id = dev_id;
+	chan->dev_str = dev_str;
+	chan->fifo_addr = dev->fifo_addr;
+	chan->mode = dev->dma_mode;
+
+	/* initialize the channel before returning */
+	init_dma(i);
+
+	return i;
+}
+EXPORT_SYMBOL(request_au1000_dma);
+
+void free_au1000_dma(unsigned int dmanr)
+{
+	struct dma_chan *chan = get_dma_chan(dmanr);
+
+	if (!chan) {
+		printk(KERN_ERR "Error trying to free DMA%d\n", dmanr);
+		return;
+	}
+
+	disable_dma(dmanr);
+	if (chan->irq_dev)
+		free_irq(chan->irq, chan->irq_dev);
+
+	chan->irq_dev = NULL;
+	chan->dev_id = -1;
+}
+EXPORT_SYMBOL(free_au1000_dma);
+
+static int __init au1000_dma_init(void)
+{
+	int base, i;
+
+	switch (alchemy_get_cputype()) {
+	case ALCHEMY_CPU_AU1000:
+		base = AU1000_DMA_INT_BASE;
+		break;
+	case ALCHEMY_CPU_AU1500:
+		base = AU1500_DMA_INT_BASE;
+		break;
+	case ALCHEMY_CPU_AU1100:
+		base = AU1100_DMA_INT_BASE;
+		break;
+	default:
+		goto out;
+	}
+
+	for (i = 0; i < NUM_AU1000_DMA_CHANNELS; i++)
+		au1000_dma_table[i].irq = base + i;
+
+	printk(KERN_INFO "Alchemy DMA initialized\n");
+
+out:
+	return 0;
+}
+arch_initcall(au1000_dma_init);
diff --git a/arch/mips/alchemy/common/gpiolib.c b/arch/mips/alchemy/common/gpiolib.c
new file mode 100644
index 000000000..1b16daaa8
--- /dev/null
+++ b/arch/mips/alchemy/common/gpiolib.c
@@ -0,0 +1,172 @@
+/*
+ *  Copyright (C) 2007-2009, OpenWrt.org, Florian Fainelli <florian@openwrt.org>
+ *	GPIOLIB support for Alchemy chips.
+ *
+ *  This program is free software; you can redistribute	 it and/or modify it
+ *  under  the terms of	 the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the	License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED	  ``AS	IS'' AND   ANY	EXPRESS OR IMPLIED
+ *  WARRANTIES,	  INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO	EVENT  SHALL   THE AUTHOR  BE	 LIABLE FOR ANY	  DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED	  TO, PROCUREMENT OF  SUBSTITUTE GOODS	OR SERVICES; LOSS OF
+ *  USE, DATA,	OR PROFITS; OR	BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN	 CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ *  Notes :
+ *	au1000 SoC have only one GPIO block : GPIO1
+ *	Au1100, Au15x0, Au12x0 have a second one : GPIO2
+ *	Au1300 is totally different: 1 block with up to 128 GPIOs
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/gpio/driver.h>
+#include <asm/mach-au1x00/gpio-au1000.h>
+#include <asm/mach-au1x00/gpio-au1300.h>
+
+static int gpio2_get(struct gpio_chip *chip, unsigned offset)
+{
+	return !!alchemy_gpio2_get_value(offset + ALCHEMY_GPIO2_BASE);
+}
+
+static void gpio2_set(struct gpio_chip *chip, unsigned offset, int value)
+{
+	alchemy_gpio2_set_value(offset + ALCHEMY_GPIO2_BASE, value);
+}
+
+static int gpio2_direction_input(struct gpio_chip *chip, unsigned offset)
+{
+	return alchemy_gpio2_direction_input(offset + ALCHEMY_GPIO2_BASE);
+}
+
+static int gpio2_direction_output(struct gpio_chip *chip, unsigned offset,
+				  int value)
+{
+	return alchemy_gpio2_direction_output(offset + ALCHEMY_GPIO2_BASE,
+						value);
+}
+
+static int gpio2_to_irq(struct gpio_chip *chip, unsigned offset)
+{
+	return alchemy_gpio2_to_irq(offset + ALCHEMY_GPIO2_BASE);
+}
+
+
+static int gpio1_get(struct gpio_chip *chip, unsigned offset)
+{
+	return !!alchemy_gpio1_get_value(offset + ALCHEMY_GPIO1_BASE);
+}
+
+static void gpio1_set(struct gpio_chip *chip,
+				unsigned offset, int value)
+{
+	alchemy_gpio1_set_value(offset + ALCHEMY_GPIO1_BASE, value);
+}
+
+static int gpio1_direction_input(struct gpio_chip *chip, unsigned offset)
+{
+	return alchemy_gpio1_direction_input(offset + ALCHEMY_GPIO1_BASE);
+}
+
+static int gpio1_direction_output(struct gpio_chip *chip,
+					unsigned offset, int value)
+{
+	return alchemy_gpio1_direction_output(offset + ALCHEMY_GPIO1_BASE,
+					     value);
+}
+
+static int gpio1_to_irq(struct gpio_chip *chip, unsigned offset)
+{
+	return alchemy_gpio1_to_irq(offset + ALCHEMY_GPIO1_BASE);
+}
+
+struct gpio_chip alchemy_gpio_chip[] = {
+	[0] = {
+		.label			= "alchemy-gpio1",
+		.direction_input	= gpio1_direction_input,
+		.direction_output	= gpio1_direction_output,
+		.get			= gpio1_get,
+		.set			= gpio1_set,
+		.to_irq			= gpio1_to_irq,
+		.base			= ALCHEMY_GPIO1_BASE,
+		.ngpio			= ALCHEMY_GPIO1_NUM,
+	},
+	[1] = {
+		.label			= "alchemy-gpio2",
+		.direction_input	= gpio2_direction_input,
+		.direction_output	= gpio2_direction_output,
+		.get			= gpio2_get,
+		.set			= gpio2_set,
+		.to_irq			= gpio2_to_irq,
+		.base			= ALCHEMY_GPIO2_BASE,
+		.ngpio			= ALCHEMY_GPIO2_NUM,
+	},
+};
+
+static int alchemy_gpic_get(struct gpio_chip *chip, unsigned int off)
+{
+	return !!au1300_gpio_get_value(off + AU1300_GPIO_BASE);
+}
+
+static void alchemy_gpic_set(struct gpio_chip *chip, unsigned int off, int v)
+{
+	au1300_gpio_set_value(off + AU1300_GPIO_BASE, v);
+}
+
+static int alchemy_gpic_dir_input(struct gpio_chip *chip, unsigned int off)
+{
+	return au1300_gpio_direction_input(off + AU1300_GPIO_BASE);
+}
+
+static int alchemy_gpic_dir_output(struct gpio_chip *chip, unsigned int off,
+				   int v)
+{
+	return au1300_gpio_direction_output(off + AU1300_GPIO_BASE, v);
+}
+
+static int alchemy_gpic_gpio_to_irq(struct gpio_chip *chip, unsigned int off)
+{
+	return au1300_gpio_to_irq(off + AU1300_GPIO_BASE);
+}
+
+static struct gpio_chip au1300_gpiochip = {
+	.label			= "alchemy-gpic",
+	.direction_input	= alchemy_gpic_dir_input,
+	.direction_output	= alchemy_gpic_dir_output,
+	.get			= alchemy_gpic_get,
+	.set			= alchemy_gpic_set,
+	.to_irq			= alchemy_gpic_gpio_to_irq,
+	.base			= AU1300_GPIO_BASE,
+	.ngpio			= AU1300_GPIO_NUM,
+};
+
+static int __init alchemy_gpiochip_init(void)
+{
+	int ret = 0;
+
+	switch (alchemy_get_cputype()) {
+	case ALCHEMY_CPU_AU1000:
+		ret = gpiochip_add_data(&alchemy_gpio_chip[0], NULL);
+		break;
+	case ALCHEMY_CPU_AU1500...ALCHEMY_CPU_AU1200:
+		ret = gpiochip_add_data(&alchemy_gpio_chip[0], NULL);
+		ret |= gpiochip_add_data(&alchemy_gpio_chip[1], NULL);
+		break;
+	case ALCHEMY_CPU_AU1300:
+		ret = gpiochip_add_data(&au1300_gpiochip, NULL);
+		break;
+	}
+	return ret;
+}
+arch_initcall(alchemy_gpiochip_init);
diff --git a/arch/mips/alchemy/common/irq.c b/arch/mips/alchemy/common/irq.c
new file mode 100644
index 000000000..da9f92200
--- /dev/null
+++ b/arch/mips/alchemy/common/irq.c
@@ -0,0 +1,996 @@
+/*
+ * Copyright 2001, 2007-2008 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc. <source@mvista.com>
+ *
+ * Copyright (C) 2007 Ralf Baechle (ralf@linux-mips.org)
+ *
+ *  This program is free software; you can redistribute	 it and/or modify it
+ *  under  the terms of	 the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the	License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED	  ``AS	IS'' AND   ANY	EXPRESS OR IMPLIED
+ *  WARRANTIES,	  INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO	EVENT  SHALL   THE AUTHOR  BE	 LIABLE FOR ANY	  DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED	  TO, PROCUREMENT OF  SUBSTITUTE GOODS	OR SERVICES; LOSS OF
+ *  USE, DATA,	OR PROFITS; OR	BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN	 CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/export.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/slab.h>
+#include <linux/syscore_ops.h>
+
+#include <asm/irq_cpu.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/gpio-au1300.h>
+
+/* Interrupt Controller register offsets */
+#define IC_CFG0RD	0x40
+#define IC_CFG0SET	0x40
+#define IC_CFG0CLR	0x44
+#define IC_CFG1RD	0x48
+#define IC_CFG1SET	0x48
+#define IC_CFG1CLR	0x4C
+#define IC_CFG2RD	0x50
+#define IC_CFG2SET	0x50
+#define IC_CFG2CLR	0x54
+#define IC_REQ0INT	0x54
+#define IC_SRCRD	0x58
+#define IC_SRCSET	0x58
+#define IC_SRCCLR	0x5C
+#define IC_REQ1INT	0x5C
+#define IC_ASSIGNRD	0x60
+#define IC_ASSIGNSET	0x60
+#define IC_ASSIGNCLR	0x64
+#define IC_WAKERD	0x68
+#define IC_WAKESET	0x68
+#define IC_WAKECLR	0x6C
+#define IC_MASKRD	0x70
+#define IC_MASKSET	0x70
+#define IC_MASKCLR	0x74
+#define IC_RISINGRD	0x78
+#define IC_RISINGCLR	0x78
+#define IC_FALLINGRD	0x7C
+#define IC_FALLINGCLR	0x7C
+#define IC_TESTBIT	0x80
+
+/* per-processor fixed function irqs */
+struct alchemy_irqmap {
+	int irq;	/* linux IRQ number */
+	int type;	/* IRQ_TYPE_ */
+	int prio;	/* irq priority, 0 highest, 3 lowest */
+	int internal;	/* GPIC: internal source (no ext. pin)? */
+};
+
+static int au1x_ic_settype(struct irq_data *d, unsigned int type);
+static int au1300_gpic_settype(struct irq_data *d, unsigned int type);
+
+
+/* NOTE on interrupt priorities: The original writers of this code said:
+ *
+ * Because of the tight timing of SETUP token to reply transactions,
+ * the USB devices-side packet complete interrupt (USB_DEV_REQ_INT)
+ * needs the highest priority.
+ */
+struct alchemy_irqmap au1000_irqmap[] __initdata = {
+	{ AU1000_UART0_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1000_UART1_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1000_UART2_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1000_UART3_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1000_SSI0_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1000_SSI1_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1000_DMA_INT_BASE,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1000_DMA_INT_BASE+1,  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1000_DMA_INT_BASE+2,  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1000_DMA_INT_BASE+3,  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1000_DMA_INT_BASE+4,  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1000_DMA_INT_BASE+5,  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1000_DMA_INT_BASE+6,  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1000_DMA_INT_BASE+7,  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1000_TOY_INT,	  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1000_TOY_MATCH0_INT,  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1000_TOY_MATCH1_INT,  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1000_TOY_MATCH2_INT,  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1000_RTC_INT,	  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1000_RTC_MATCH0_INT,  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1000_RTC_MATCH1_INT,  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1000_RTC_MATCH2_INT,  IRQ_TYPE_EDGE_RISING, 0, 0 },
+	{ AU1000_IRDA_TX_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1000_IRDA_RX_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1000_USB_DEV_REQ_INT, IRQ_TYPE_LEVEL_HIGH,	0, 0 },
+	{ AU1000_USB_DEV_SUS_INT, IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1000_USB_HOST_INT,	  IRQ_TYPE_LEVEL_LOW,	1, 0 },
+	{ AU1000_ACSYNC_INT,	  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1000_MAC0_DMA_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1000_MAC1_DMA_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1000_AC97C_INT,	  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ -1, },
+};
+
+struct alchemy_irqmap au1500_irqmap[] __initdata = {
+	{ AU1500_UART0_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1500_PCI_INTA,	  IRQ_TYPE_LEVEL_LOW,	1, 0 },
+	{ AU1500_PCI_INTB,	  IRQ_TYPE_LEVEL_LOW,	1, 0 },
+	{ AU1500_UART3_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1500_PCI_INTC,	  IRQ_TYPE_LEVEL_LOW,	1, 0 },
+	{ AU1500_PCI_INTD,	  IRQ_TYPE_LEVEL_LOW,	1, 0 },
+	{ AU1500_DMA_INT_BASE,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1500_DMA_INT_BASE+1,  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1500_DMA_INT_BASE+2,  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1500_DMA_INT_BASE+3,  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1500_DMA_INT_BASE+4,  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1500_DMA_INT_BASE+5,  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1500_DMA_INT_BASE+6,  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1500_DMA_INT_BASE+7,  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1500_TOY_INT,	  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1500_TOY_MATCH0_INT,  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1500_TOY_MATCH1_INT,  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1500_TOY_MATCH2_INT,  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1500_RTC_INT,	  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1500_RTC_MATCH0_INT,  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1500_RTC_MATCH1_INT,  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1500_RTC_MATCH2_INT,  IRQ_TYPE_EDGE_RISING, 0, 0 },
+	{ AU1500_USB_DEV_REQ_INT, IRQ_TYPE_LEVEL_HIGH,	0, 0 },
+	{ AU1500_USB_DEV_SUS_INT, IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1500_USB_HOST_INT,	  IRQ_TYPE_LEVEL_LOW,	1, 0 },
+	{ AU1500_ACSYNC_INT,	  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1500_MAC0_DMA_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1500_MAC1_DMA_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1500_AC97C_INT,	  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ -1, },
+};
+
+struct alchemy_irqmap au1100_irqmap[] __initdata = {
+	{ AU1100_UART0_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1100_UART1_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1100_SD_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1100_UART3_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1100_SSI0_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1100_SSI1_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1100_DMA_INT_BASE,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1100_DMA_INT_BASE+1,  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1100_DMA_INT_BASE+2,  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1100_DMA_INT_BASE+3,  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1100_DMA_INT_BASE+4,  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1100_DMA_INT_BASE+5,  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1100_DMA_INT_BASE+6,  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1100_DMA_INT_BASE+7,  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1100_TOY_INT,	  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1100_TOY_MATCH0_INT,  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1100_TOY_MATCH1_INT,  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1100_TOY_MATCH2_INT,  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1100_RTC_INT,	  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1100_RTC_MATCH0_INT,  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1100_RTC_MATCH1_INT,  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1100_RTC_MATCH2_INT,  IRQ_TYPE_EDGE_RISING, 0, 0 },
+	{ AU1100_IRDA_TX_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1100_IRDA_RX_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1100_USB_DEV_REQ_INT, IRQ_TYPE_LEVEL_HIGH,	0, 0 },
+	{ AU1100_USB_DEV_SUS_INT, IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1100_USB_HOST_INT,	  IRQ_TYPE_LEVEL_LOW,	1, 0 },
+	{ AU1100_ACSYNC_INT,	  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1100_MAC0_DMA_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1100_LCD_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1100_AC97C_INT,	  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ -1, },
+};
+
+struct alchemy_irqmap au1550_irqmap[] __initdata = {
+	{ AU1550_UART0_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1550_PCI_INTA,	  IRQ_TYPE_LEVEL_LOW,	1, 0 },
+	{ AU1550_PCI_INTB,	  IRQ_TYPE_LEVEL_LOW,	1, 0 },
+	{ AU1550_DDMA_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1550_CRYPTO_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1550_PCI_INTC,	  IRQ_TYPE_LEVEL_LOW,	1, 0 },
+	{ AU1550_PCI_INTD,	  IRQ_TYPE_LEVEL_LOW,	1, 0 },
+	{ AU1550_PCI_RST_INT,	  IRQ_TYPE_LEVEL_LOW,	1, 0 },
+	{ AU1550_UART1_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1550_UART3_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1550_PSC0_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1550_PSC1_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1550_PSC2_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1550_PSC3_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1550_TOY_INT,	  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1550_TOY_MATCH0_INT,  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1550_TOY_MATCH1_INT,  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1550_TOY_MATCH2_INT,  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1550_RTC_INT,	  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1550_RTC_MATCH0_INT,  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1550_RTC_MATCH1_INT,  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1550_RTC_MATCH2_INT,  IRQ_TYPE_EDGE_RISING, 0, 0 },
+	{ AU1550_NAND_INT,	  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1550_USB_DEV_REQ_INT, IRQ_TYPE_LEVEL_HIGH,	0, 0 },
+	{ AU1550_USB_DEV_SUS_INT, IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1550_USB_HOST_INT,	  IRQ_TYPE_LEVEL_LOW,	1, 0 },
+	{ AU1550_MAC0_DMA_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1550_MAC1_DMA_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ -1, },
+};
+
+struct alchemy_irqmap au1200_irqmap[] __initdata = {
+	{ AU1200_UART0_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1200_SWT_INT,	  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1200_SD_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1200_DDMA_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1200_MAE_BE_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1200_UART1_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1200_MAE_FE_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1200_PSC0_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1200_PSC1_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1200_AES_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1200_CAMERA_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1200_TOY_INT,	  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1200_TOY_MATCH0_INT,  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1200_TOY_MATCH1_INT,  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1200_TOY_MATCH2_INT,  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1200_RTC_INT,	  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1200_RTC_MATCH0_INT,  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1200_RTC_MATCH1_INT,  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1200_RTC_MATCH2_INT,  IRQ_TYPE_EDGE_RISING, 0, 0 },
+	{ AU1200_NAND_INT,	  IRQ_TYPE_EDGE_RISING, 1, 0 },
+	{ AU1200_USB_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1200_LCD_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ AU1200_MAE_BOTH_INT,	  IRQ_TYPE_LEVEL_HIGH,	1, 0 },
+	{ -1, },
+};
+
+static struct alchemy_irqmap au1300_irqmap[] __initdata = {
+	/* multifunction: gpio pin or device */
+	{ AU1300_UART1_INT,	 IRQ_TYPE_LEVEL_HIGH,	1, 0, },
+	{ AU1300_UART2_INT,	 IRQ_TYPE_LEVEL_HIGH,	1, 0, },
+	{ AU1300_UART3_INT,	 IRQ_TYPE_LEVEL_HIGH,	1, 0, },
+	{ AU1300_SD1_INT,	 IRQ_TYPE_LEVEL_HIGH,	1, 0, },
+	{ AU1300_SD2_INT,	 IRQ_TYPE_LEVEL_HIGH,	1, 0, },
+	{ AU1300_PSC0_INT,	 IRQ_TYPE_LEVEL_HIGH,	1, 0, },
+	{ AU1300_PSC1_INT,	 IRQ_TYPE_LEVEL_HIGH,	1, 0, },
+	{ AU1300_PSC2_INT,	 IRQ_TYPE_LEVEL_HIGH,	1, 0, },
+	{ AU1300_PSC3_INT,	 IRQ_TYPE_LEVEL_HIGH,	1, 0, },
+	{ AU1300_NAND_INT,	 IRQ_TYPE_LEVEL_HIGH,	1, 0, },
+	/* au1300 internal */
+	{ AU1300_DDMA_INT,	 IRQ_TYPE_LEVEL_HIGH,	1, 1, },
+	{ AU1300_MMU_INT,	 IRQ_TYPE_LEVEL_HIGH,	1, 1, },
+	{ AU1300_MPU_INT,	 IRQ_TYPE_LEVEL_HIGH,	1, 1, },
+	{ AU1300_GPU_INT,	 IRQ_TYPE_LEVEL_HIGH,	1, 1, },
+	{ AU1300_UDMA_INT,	 IRQ_TYPE_LEVEL_HIGH,	1, 1, },
+	{ AU1300_TOY_INT,	 IRQ_TYPE_EDGE_RISING,	1, 1, },
+	{ AU1300_TOY_MATCH0_INT, IRQ_TYPE_EDGE_RISING,	1, 1, },
+	{ AU1300_TOY_MATCH1_INT, IRQ_TYPE_EDGE_RISING,	1, 1, },
+	{ AU1300_TOY_MATCH2_INT, IRQ_TYPE_EDGE_RISING,	1, 1, },
+	{ AU1300_RTC_INT,	 IRQ_TYPE_EDGE_RISING,	1, 1, },
+	{ AU1300_RTC_MATCH0_INT, IRQ_TYPE_EDGE_RISING,	1, 1, },
+	{ AU1300_RTC_MATCH1_INT, IRQ_TYPE_EDGE_RISING,	1, 1, },
+	{ AU1300_RTC_MATCH2_INT, IRQ_TYPE_EDGE_RISING,	0, 1, },
+	{ AU1300_UART0_INT,	 IRQ_TYPE_LEVEL_HIGH,	1, 1, },
+	{ AU1300_SD0_INT,	 IRQ_TYPE_LEVEL_HIGH,	1, 1, },
+	{ AU1300_USB_INT,	 IRQ_TYPE_LEVEL_HIGH,	1, 1, },
+	{ AU1300_LCD_INT,	 IRQ_TYPE_LEVEL_HIGH,	1, 1, },
+	{ AU1300_BSA_INT,	 IRQ_TYPE_LEVEL_HIGH,	1, 1, },
+	{ AU1300_MPE_INT,	 IRQ_TYPE_EDGE_RISING,	1, 1, },
+	{ AU1300_ITE_INT,	 IRQ_TYPE_LEVEL_HIGH,	1, 1, },
+	{ AU1300_AES_INT,	 IRQ_TYPE_LEVEL_HIGH,	1, 1, },
+	{ AU1300_CIM_INT,	 IRQ_TYPE_LEVEL_HIGH,	1, 1, },
+	{ -1, },	/* terminator */
+};
+
+/******************************************************************************/
+
+static void au1x_ic0_unmask(struct irq_data *d)
+{
+	unsigned int bit = d->irq - AU1000_INTC0_INT_BASE;
+	void __iomem *base = (void __iomem *)KSEG1ADDR(AU1000_IC0_PHYS_ADDR);
+
+	__raw_writel(1 << bit, base + IC_MASKSET);
+	__raw_writel(1 << bit, base + IC_WAKESET);
+	wmb();
+}
+
+static void au1x_ic1_unmask(struct irq_data *d)
+{
+	unsigned int bit = d->irq - AU1000_INTC1_INT_BASE;
+	void __iomem *base = (void __iomem *)KSEG1ADDR(AU1000_IC1_PHYS_ADDR);
+
+	__raw_writel(1 << bit, base + IC_MASKSET);
+	__raw_writel(1 << bit, base + IC_WAKESET);
+	wmb();
+}
+
+static void au1x_ic0_mask(struct irq_data *d)
+{
+	unsigned int bit = d->irq - AU1000_INTC0_INT_BASE;
+	void __iomem *base = (void __iomem *)KSEG1ADDR(AU1000_IC0_PHYS_ADDR);
+
+	__raw_writel(1 << bit, base + IC_MASKCLR);
+	__raw_writel(1 << bit, base + IC_WAKECLR);
+	wmb();
+}
+
+static void au1x_ic1_mask(struct irq_data *d)
+{
+	unsigned int bit = d->irq - AU1000_INTC1_INT_BASE;
+	void __iomem *base = (void __iomem *)KSEG1ADDR(AU1000_IC1_PHYS_ADDR);
+
+	__raw_writel(1 << bit, base + IC_MASKCLR);
+	__raw_writel(1 << bit, base + IC_WAKECLR);
+	wmb();
+}
+
+static void au1x_ic0_ack(struct irq_data *d)
+{
+	unsigned int bit = d->irq - AU1000_INTC0_INT_BASE;
+	void __iomem *base = (void __iomem *)KSEG1ADDR(AU1000_IC0_PHYS_ADDR);
+
+	/*
+	 * This may assume that we don't get interrupts from
+	 * both edges at once, or if we do, that we don't care.
+	 */
+	__raw_writel(1 << bit, base + IC_FALLINGCLR);
+	__raw_writel(1 << bit, base + IC_RISINGCLR);
+	wmb();
+}
+
+static void au1x_ic1_ack(struct irq_data *d)
+{
+	unsigned int bit = d->irq - AU1000_INTC1_INT_BASE;
+	void __iomem *base = (void __iomem *)KSEG1ADDR(AU1000_IC1_PHYS_ADDR);
+
+	/*
+	 * This may assume that we don't get interrupts from
+	 * both edges at once, or if we do, that we don't care.
+	 */
+	__raw_writel(1 << bit, base + IC_FALLINGCLR);
+	__raw_writel(1 << bit, base + IC_RISINGCLR);
+	wmb();
+}
+
+static void au1x_ic0_maskack(struct irq_data *d)
+{
+	unsigned int bit = d->irq - AU1000_INTC0_INT_BASE;
+	void __iomem *base = (void __iomem *)KSEG1ADDR(AU1000_IC0_PHYS_ADDR);
+
+	__raw_writel(1 << bit, base + IC_WAKECLR);
+	__raw_writel(1 << bit, base + IC_MASKCLR);
+	__raw_writel(1 << bit, base + IC_RISINGCLR);
+	__raw_writel(1 << bit, base + IC_FALLINGCLR);
+	wmb();
+}
+
+static void au1x_ic1_maskack(struct irq_data *d)
+{
+	unsigned int bit = d->irq - AU1000_INTC1_INT_BASE;
+	void __iomem *base = (void __iomem *)KSEG1ADDR(AU1000_IC1_PHYS_ADDR);
+
+	__raw_writel(1 << bit, base + IC_WAKECLR);
+	__raw_writel(1 << bit, base + IC_MASKCLR);
+	__raw_writel(1 << bit, base + IC_RISINGCLR);
+	__raw_writel(1 << bit, base + IC_FALLINGCLR);
+	wmb();
+}
+
+static int au1x_ic1_setwake(struct irq_data *d, unsigned int on)
+{
+	int bit = d->irq - AU1000_INTC1_INT_BASE;
+	unsigned long wakemsk, flags;
+
+	/* only GPIO 0-7 can act as wakeup source.  Fortunately these
+	 * are wired up identically on all supported variants.
+	 */
+	if ((bit < 0) || (bit > 7))
+		return -EINVAL;
+
+	local_irq_save(flags);
+	wakemsk = alchemy_rdsys(AU1000_SYS_WAKEMSK);
+	if (on)
+		wakemsk |= 1 << bit;
+	else
+		wakemsk &= ~(1 << bit);
+	alchemy_wrsys(wakemsk, AU1000_SYS_WAKEMSK);
+	local_irq_restore(flags);
+
+	return 0;
+}
+
+/*
+ * irq_chips for both ICs; this way the mask handlers can be
+ * as short as possible.
+ */
+static struct irq_chip au1x_ic0_chip = {
+	.name		= "Alchemy-IC0",
+	.irq_ack	= au1x_ic0_ack,
+	.irq_mask	= au1x_ic0_mask,
+	.irq_mask_ack	= au1x_ic0_maskack,
+	.irq_unmask	= au1x_ic0_unmask,
+	.irq_set_type	= au1x_ic_settype,
+};
+
+static struct irq_chip au1x_ic1_chip = {
+	.name		= "Alchemy-IC1",
+	.irq_ack	= au1x_ic1_ack,
+	.irq_mask	= au1x_ic1_mask,
+	.irq_mask_ack	= au1x_ic1_maskack,
+	.irq_unmask	= au1x_ic1_unmask,
+	.irq_set_type	= au1x_ic_settype,
+	.irq_set_wake	= au1x_ic1_setwake,
+};
+
+static int au1x_ic_settype(struct irq_data *d, unsigned int flow_type)
+{
+	struct irq_chip *chip;
+	unsigned int bit, irq = d->irq;
+	irq_flow_handler_t handler = NULL;
+	unsigned char *name = NULL;
+	void __iomem *base;
+	int ret;
+
+	if (irq >= AU1000_INTC1_INT_BASE) {
+		bit = irq - AU1000_INTC1_INT_BASE;
+		chip = &au1x_ic1_chip;
+		base = (void __iomem *)KSEG1ADDR(AU1000_IC1_PHYS_ADDR);
+	} else {
+		bit = irq - AU1000_INTC0_INT_BASE;
+		chip = &au1x_ic0_chip;
+		base = (void __iomem *)KSEG1ADDR(AU1000_IC0_PHYS_ADDR);
+	}
+
+	if (bit > 31)
+		return -EINVAL;
+
+	ret = 0;
+
+	switch (flow_type) {	/* cfgregs 2:1:0 */
+	case IRQ_TYPE_EDGE_RISING:	/* 0:0:1 */
+		__raw_writel(1 << bit, base + IC_CFG2CLR);
+		__raw_writel(1 << bit, base + IC_CFG1CLR);
+		__raw_writel(1 << bit, base + IC_CFG0SET);
+		handler = handle_edge_irq;
+		name = "riseedge";
+		break;
+	case IRQ_TYPE_EDGE_FALLING:	/* 0:1:0 */
+		__raw_writel(1 << bit, base + IC_CFG2CLR);
+		__raw_writel(1 << bit, base + IC_CFG1SET);
+		__raw_writel(1 << bit, base + IC_CFG0CLR);
+		handler = handle_edge_irq;
+		name = "falledge";
+		break;
+	case IRQ_TYPE_EDGE_BOTH:	/* 0:1:1 */
+		__raw_writel(1 << bit, base + IC_CFG2CLR);
+		__raw_writel(1 << bit, base + IC_CFG1SET);
+		__raw_writel(1 << bit, base + IC_CFG0SET);
+		handler = handle_edge_irq;
+		name = "bothedge";
+		break;
+	case IRQ_TYPE_LEVEL_HIGH:	/* 1:0:1 */
+		__raw_writel(1 << bit, base + IC_CFG2SET);
+		__raw_writel(1 << bit, base + IC_CFG1CLR);
+		__raw_writel(1 << bit, base + IC_CFG0SET);
+		handler = handle_level_irq;
+		name = "hilevel";
+		break;
+	case IRQ_TYPE_LEVEL_LOW:	/* 1:1:0 */
+		__raw_writel(1 << bit, base + IC_CFG2SET);
+		__raw_writel(1 << bit, base + IC_CFG1SET);
+		__raw_writel(1 << bit, base + IC_CFG0CLR);
+		handler = handle_level_irq;
+		name = "lowlevel";
+		break;
+	case IRQ_TYPE_NONE:		/* 0:0:0 */
+		__raw_writel(1 << bit, base + IC_CFG2CLR);
+		__raw_writel(1 << bit, base + IC_CFG1CLR);
+		__raw_writel(1 << bit, base + IC_CFG0CLR);
+		break;
+	default:
+		ret = -EINVAL;
+	}
+	irq_set_chip_handler_name_locked(d, chip, handler, name);
+
+	wmb();
+
+	return ret;
+}
+
+/******************************************************************************/
+
+/*
+ * au1300_gpic_chgcfg - change PIN configuration.
+ * @gpio:	pin to change (0-based GPIO number from datasheet).
+ * @clr:	clear all bits set in 'clr'.
+ * @set:	set these bits.
+ *
+ * modifies a pins' configuration register, bits set in @clr will
+ * be cleared in the register, bits in @set will be set.
+ */
+static inline void au1300_gpic_chgcfg(unsigned int gpio,
+				      unsigned long clr,
+				      unsigned long set)
+{
+	void __iomem *r = AU1300_GPIC_ADDR;
+	unsigned long l;
+
+	r += gpio * 4;	/* offset into pin config array */
+	l = __raw_readl(r + AU1300_GPIC_PINCFG);
+	l &= ~clr;
+	l |= set;
+	__raw_writel(l, r + AU1300_GPIC_PINCFG);
+	wmb();
+}
+
+/*
+ * au1300_pinfunc_to_gpio - assign a pin as GPIO input (GPIO ctrl).
+ * @pin:	pin (0-based GPIO number from datasheet).
+ *
+ * Assigns a GPIO pin to the GPIO controller, so its level can either
+ * be read or set through the generic GPIO functions.
+ * If you need a GPOUT, use au1300_gpio_set_value(pin, 0/1).
+ * REVISIT: is this function really necessary?
+ */
+void au1300_pinfunc_to_gpio(enum au1300_multifunc_pins gpio)
+{
+	au1300_gpio_direction_input(gpio + AU1300_GPIO_BASE);
+}
+EXPORT_SYMBOL_GPL(au1300_pinfunc_to_gpio);
+
+/*
+ * au1300_pinfunc_to_dev - assign a pin to the device function.
+ * @pin:	pin (0-based GPIO number from datasheet).
+ *
+ * Assigns a GPIO pin to its associated device function; the pin will be
+ * driven by the device and not through GPIO functions.
+ */
+void au1300_pinfunc_to_dev(enum au1300_multifunc_pins gpio)
+{
+	void __iomem *r = AU1300_GPIC_ADDR;
+	unsigned long bit;
+
+	r += GPIC_GPIO_BANKOFF(gpio);
+	bit = GPIC_GPIO_TO_BIT(gpio);
+	__raw_writel(bit, r + AU1300_GPIC_DEVSEL);
+	wmb();
+}
+EXPORT_SYMBOL_GPL(au1300_pinfunc_to_dev);
+
+/*
+ * au1300_set_irq_priority -  set internal priority of IRQ.
+ * @irq:	irq to set priority (linux irq number).
+ * @p:		priority (0 = highest, 3 = lowest).
+ */
+void au1300_set_irq_priority(unsigned int irq, int p)
+{
+	irq -= ALCHEMY_GPIC_INT_BASE;
+	au1300_gpic_chgcfg(irq, GPIC_CFG_IL_MASK, GPIC_CFG_IL_SET(p));
+}
+EXPORT_SYMBOL_GPL(au1300_set_irq_priority);
+
+/*
+ * au1300_set_dbdma_gpio - assign a gpio to one of the DBDMA triggers.
+ * @dchan:	dbdma trigger select (0, 1).
+ * @gpio:	pin to assign as trigger.
+ *
+ * DBDMA controller has 2 external trigger sources; this function
+ * assigns a GPIO to the selected trigger.
+ */
+void au1300_set_dbdma_gpio(int dchan, unsigned int gpio)
+{
+	unsigned long r;
+
+	if ((dchan >= 0) && (dchan <= 1)) {
+		r = __raw_readl(AU1300_GPIC_ADDR + AU1300_GPIC_DMASEL);
+		r &= ~(0xff << (8 * dchan));
+		r |= (gpio & 0x7f) << (8 * dchan);
+		__raw_writel(r, AU1300_GPIC_ADDR + AU1300_GPIC_DMASEL);
+		wmb();
+	}
+}
+
+static inline void gpic_pin_set_idlewake(unsigned int gpio, int allow)
+{
+	au1300_gpic_chgcfg(gpio, GPIC_CFG_IDLEWAKE,
+			   allow ? GPIC_CFG_IDLEWAKE : 0);
+}
+
+static void au1300_gpic_mask(struct irq_data *d)
+{
+	void __iomem *r = AU1300_GPIC_ADDR;
+	unsigned long bit, irq = d->irq;
+
+	irq -= ALCHEMY_GPIC_INT_BASE;
+	r += GPIC_GPIO_BANKOFF(irq);
+	bit = GPIC_GPIO_TO_BIT(irq);
+	__raw_writel(bit, r + AU1300_GPIC_IDIS);
+	wmb();
+
+	gpic_pin_set_idlewake(irq, 0);
+}
+
+static void au1300_gpic_unmask(struct irq_data *d)
+{
+	void __iomem *r = AU1300_GPIC_ADDR;
+	unsigned long bit, irq = d->irq;
+
+	irq -= ALCHEMY_GPIC_INT_BASE;
+
+	gpic_pin_set_idlewake(irq, 1);
+
+	r += GPIC_GPIO_BANKOFF(irq);
+	bit = GPIC_GPIO_TO_BIT(irq);
+	__raw_writel(bit, r + AU1300_GPIC_IEN);
+	wmb();
+}
+
+static void au1300_gpic_maskack(struct irq_data *d)
+{
+	void __iomem *r = AU1300_GPIC_ADDR;
+	unsigned long bit, irq = d->irq;
+
+	irq -= ALCHEMY_GPIC_INT_BASE;
+	r += GPIC_GPIO_BANKOFF(irq);
+	bit = GPIC_GPIO_TO_BIT(irq);
+	__raw_writel(bit, r + AU1300_GPIC_IPEND);	/* ack */
+	__raw_writel(bit, r + AU1300_GPIC_IDIS);	/* mask */
+	wmb();
+
+	gpic_pin_set_idlewake(irq, 0);
+}
+
+static void au1300_gpic_ack(struct irq_data *d)
+{
+	void __iomem *r = AU1300_GPIC_ADDR;
+	unsigned long bit, irq = d->irq;
+
+	irq -= ALCHEMY_GPIC_INT_BASE;
+	r += GPIC_GPIO_BANKOFF(irq);
+	bit = GPIC_GPIO_TO_BIT(irq);
+	__raw_writel(bit, r + AU1300_GPIC_IPEND);	/* ack */
+	wmb();
+}
+
+static struct irq_chip au1300_gpic = {
+	.name		= "GPIOINT",
+	.irq_ack	= au1300_gpic_ack,
+	.irq_mask	= au1300_gpic_mask,
+	.irq_mask_ack	= au1300_gpic_maskack,
+	.irq_unmask	= au1300_gpic_unmask,
+	.irq_set_type	= au1300_gpic_settype,
+};
+
+static int au1300_gpic_settype(struct irq_data *d, unsigned int type)
+{
+	unsigned long s;
+	unsigned char *name = NULL;
+	irq_flow_handler_t hdl = NULL;
+
+	switch (type) {
+	case IRQ_TYPE_LEVEL_HIGH:
+		s = GPIC_CFG_IC_LEVEL_HIGH;
+		name = "high";
+		hdl = handle_level_irq;
+		break;
+	case IRQ_TYPE_LEVEL_LOW:
+		s = GPIC_CFG_IC_LEVEL_LOW;
+		name = "low";
+		hdl = handle_level_irq;
+		break;
+	case IRQ_TYPE_EDGE_RISING:
+		s = GPIC_CFG_IC_EDGE_RISE;
+		name = "posedge";
+		hdl = handle_edge_irq;
+		break;
+	case IRQ_TYPE_EDGE_FALLING:
+		s = GPIC_CFG_IC_EDGE_FALL;
+		name = "negedge";
+		hdl = handle_edge_irq;
+		break;
+	case IRQ_TYPE_EDGE_BOTH:
+		s = GPIC_CFG_IC_EDGE_BOTH;
+		name = "bothedge";
+		hdl = handle_edge_irq;
+		break;
+	case IRQ_TYPE_NONE:
+		s = GPIC_CFG_IC_OFF;
+		name = "disabled";
+		hdl = handle_level_irq;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	irq_set_chip_handler_name_locked(d, &au1300_gpic, hdl, name);
+
+	au1300_gpic_chgcfg(d->irq - ALCHEMY_GPIC_INT_BASE, GPIC_CFG_IC_MASK, s);
+
+	return 0;
+}
+
+/******************************************************************************/
+
+static inline void ic_init(void __iomem *base)
+{
+	/* initialize interrupt controller to a safe state */
+	__raw_writel(0xffffffff, base + IC_CFG0CLR);
+	__raw_writel(0xffffffff, base + IC_CFG1CLR);
+	__raw_writel(0xffffffff, base + IC_CFG2CLR);
+	__raw_writel(0xffffffff, base + IC_MASKCLR);
+	__raw_writel(0xffffffff, base + IC_ASSIGNCLR);
+	__raw_writel(0xffffffff, base + IC_WAKECLR);
+	__raw_writel(0xffffffff, base + IC_SRCSET);
+	__raw_writel(0xffffffff, base + IC_FALLINGCLR);
+	__raw_writel(0xffffffff, base + IC_RISINGCLR);
+	__raw_writel(0x00000000, base + IC_TESTBIT);
+	wmb();
+}
+
+static unsigned long alchemy_gpic_pmdata[ALCHEMY_GPIC_INT_NUM + 6];
+
+static inline void alchemy_ic_suspend_one(void __iomem *base, unsigned long *d)
+{
+	d[0] = __raw_readl(base + IC_CFG0RD);
+	d[1] = __raw_readl(base + IC_CFG1RD);
+	d[2] = __raw_readl(base + IC_CFG2RD);
+	d[3] = __raw_readl(base + IC_SRCRD);
+	d[4] = __raw_readl(base + IC_ASSIGNRD);
+	d[5] = __raw_readl(base + IC_WAKERD);
+	d[6] = __raw_readl(base + IC_MASKRD);
+	ic_init(base);		/* shut it up too while at it */
+}
+
+static inline void alchemy_ic_resume_one(void __iomem *base, unsigned long *d)
+{
+	ic_init(base);
+
+	__raw_writel(d[0], base + IC_CFG0SET);
+	__raw_writel(d[1], base + IC_CFG1SET);
+	__raw_writel(d[2], base + IC_CFG2SET);
+	__raw_writel(d[3], base + IC_SRCSET);
+	__raw_writel(d[4], base + IC_ASSIGNSET);
+	__raw_writel(d[5], base + IC_WAKESET);
+	wmb();
+
+	__raw_writel(d[6], base + IC_MASKSET);
+	wmb();
+}
+
+static int alchemy_ic_suspend(void)
+{
+	alchemy_ic_suspend_one((void __iomem *)KSEG1ADDR(AU1000_IC0_PHYS_ADDR),
+			       alchemy_gpic_pmdata);
+	alchemy_ic_suspend_one((void __iomem *)KSEG1ADDR(AU1000_IC1_PHYS_ADDR),
+			       &alchemy_gpic_pmdata[7]);
+	return 0;
+}
+
+static void alchemy_ic_resume(void)
+{
+	alchemy_ic_resume_one((void __iomem *)KSEG1ADDR(AU1000_IC1_PHYS_ADDR),
+			      &alchemy_gpic_pmdata[7]);
+	alchemy_ic_resume_one((void __iomem *)KSEG1ADDR(AU1000_IC0_PHYS_ADDR),
+			      alchemy_gpic_pmdata);
+}
+
+static int alchemy_gpic_suspend(void)
+{
+	void __iomem *base = (void __iomem *)KSEG1ADDR(AU1300_GPIC_PHYS_ADDR);
+	int i;
+
+	/* save 4 interrupt mask status registers */
+	alchemy_gpic_pmdata[0] = __raw_readl(base + AU1300_GPIC_IEN + 0x0);
+	alchemy_gpic_pmdata[1] = __raw_readl(base + AU1300_GPIC_IEN + 0x4);
+	alchemy_gpic_pmdata[2] = __raw_readl(base + AU1300_GPIC_IEN + 0x8);
+	alchemy_gpic_pmdata[3] = __raw_readl(base + AU1300_GPIC_IEN + 0xc);
+
+	/* save misc register(s) */
+	alchemy_gpic_pmdata[4] = __raw_readl(base + AU1300_GPIC_DMASEL);
+
+	/* molto silenzioso */
+	__raw_writel(~0UL, base + AU1300_GPIC_IDIS + 0x0);
+	__raw_writel(~0UL, base + AU1300_GPIC_IDIS + 0x4);
+	__raw_writel(~0UL, base + AU1300_GPIC_IDIS + 0x8);
+	__raw_writel(~0UL, base + AU1300_GPIC_IDIS + 0xc);
+	wmb();
+
+	/* save pin/int-type configuration */
+	base += AU1300_GPIC_PINCFG;
+	for (i = 0; i < ALCHEMY_GPIC_INT_NUM; i++)
+		alchemy_gpic_pmdata[i + 5] = __raw_readl(base + (i << 2));
+
+	wmb();
+
+	return 0;
+}
+
+static void alchemy_gpic_resume(void)
+{
+	void __iomem *base = (void __iomem *)KSEG1ADDR(AU1300_GPIC_PHYS_ADDR);
+	int i;
+
+	/* disable all first */
+	__raw_writel(~0UL, base + AU1300_GPIC_IDIS + 0x0);
+	__raw_writel(~0UL, base + AU1300_GPIC_IDIS + 0x4);
+	__raw_writel(~0UL, base + AU1300_GPIC_IDIS + 0x8);
+	__raw_writel(~0UL, base + AU1300_GPIC_IDIS + 0xc);
+	wmb();
+
+	/* restore pin/int-type configurations */
+	base += AU1300_GPIC_PINCFG;
+	for (i = 0; i < ALCHEMY_GPIC_INT_NUM; i++)
+		__raw_writel(alchemy_gpic_pmdata[i + 5], base + (i << 2));
+	wmb();
+
+	/* restore misc register(s) */
+	base = (void __iomem *)KSEG1ADDR(AU1300_GPIC_PHYS_ADDR);
+	__raw_writel(alchemy_gpic_pmdata[4], base + AU1300_GPIC_DMASEL);
+	wmb();
+
+	/* finally restore masks */
+	__raw_writel(alchemy_gpic_pmdata[0], base + AU1300_GPIC_IEN + 0x0);
+	__raw_writel(alchemy_gpic_pmdata[1], base + AU1300_GPIC_IEN + 0x4);
+	__raw_writel(alchemy_gpic_pmdata[2], base + AU1300_GPIC_IEN + 0x8);
+	__raw_writel(alchemy_gpic_pmdata[3], base + AU1300_GPIC_IEN + 0xc);
+	wmb();
+}
+
+static struct syscore_ops alchemy_ic_pmops = {
+	.suspend	= alchemy_ic_suspend,
+	.resume		= alchemy_ic_resume,
+};
+
+static struct syscore_ops alchemy_gpic_pmops = {
+	.suspend	= alchemy_gpic_suspend,
+	.resume		= alchemy_gpic_resume,
+};
+
+/******************************************************************************/
+
+/* create chained handlers for the 4 IC requests to the MIPS IRQ ctrl */
+#define DISP(name, base, addr)						      \
+static void au1000_##name##_dispatch(struct irq_desc *d)		      \
+{									      \
+	unsigned long r = __raw_readl((void __iomem *)KSEG1ADDR(addr));	      \
+	if (likely(r))							      \
+		generic_handle_irq(base + __ffs(r));			      \
+	else								      \
+		spurious_interrupt();					      \
+}
+
+DISP(ic0r0, AU1000_INTC0_INT_BASE, AU1000_IC0_PHYS_ADDR + IC_REQ0INT)
+DISP(ic0r1, AU1000_INTC0_INT_BASE, AU1000_IC0_PHYS_ADDR + IC_REQ1INT)
+DISP(ic1r0, AU1000_INTC1_INT_BASE, AU1000_IC1_PHYS_ADDR + IC_REQ0INT)
+DISP(ic1r1, AU1000_INTC1_INT_BASE, AU1000_IC1_PHYS_ADDR + IC_REQ1INT)
+
+static void alchemy_gpic_dispatch(struct irq_desc *d)
+{
+	int i = __raw_readl(AU1300_GPIC_ADDR + AU1300_GPIC_PRIENC);
+	generic_handle_irq(ALCHEMY_GPIC_INT_BASE + i);
+}
+
+/******************************************************************************/
+
+static void __init au1000_init_irq(struct alchemy_irqmap *map)
+{
+	unsigned int bit, irq_nr;
+	void __iomem *base;
+
+	ic_init((void __iomem *)KSEG1ADDR(AU1000_IC0_PHYS_ADDR));
+	ic_init((void __iomem *)KSEG1ADDR(AU1000_IC1_PHYS_ADDR));
+	register_syscore_ops(&alchemy_ic_pmops);
+	mips_cpu_irq_init();
+
+	/* register all 64 possible IC0+IC1 irq sources as type "none".
+	 * Use set_irq_type() to set edge/level behaviour at runtime.
+	 */
+	for (irq_nr = AU1000_INTC0_INT_BASE;
+	     (irq_nr < AU1000_INTC0_INT_BASE + 32); irq_nr++)
+		au1x_ic_settype(irq_get_irq_data(irq_nr), IRQ_TYPE_NONE);
+
+	for (irq_nr = AU1000_INTC1_INT_BASE;
+	     (irq_nr < AU1000_INTC1_INT_BASE + 32); irq_nr++)
+		au1x_ic_settype(irq_get_irq_data(irq_nr), IRQ_TYPE_NONE);
+
+	/*
+	 * Initialize IC0, which is fixed per processor.
+	 */
+	while (map->irq != -1) {
+		irq_nr = map->irq;
+
+		if (irq_nr >= AU1000_INTC1_INT_BASE) {
+			bit = irq_nr - AU1000_INTC1_INT_BASE;
+			base = (void __iomem *)KSEG1ADDR(AU1000_IC1_PHYS_ADDR);
+		} else {
+			bit = irq_nr - AU1000_INTC0_INT_BASE;
+			base = (void __iomem *)KSEG1ADDR(AU1000_IC0_PHYS_ADDR);
+		}
+		if (map->prio == 0)
+			__raw_writel(1 << bit, base + IC_ASSIGNSET);
+
+		au1x_ic_settype(irq_get_irq_data(irq_nr), map->type);
+		++map;
+	}
+
+	irq_set_chained_handler(MIPS_CPU_IRQ_BASE + 2, au1000_ic0r0_dispatch);
+	irq_set_chained_handler(MIPS_CPU_IRQ_BASE + 3, au1000_ic0r1_dispatch);
+	irq_set_chained_handler(MIPS_CPU_IRQ_BASE + 4, au1000_ic1r0_dispatch);
+	irq_set_chained_handler(MIPS_CPU_IRQ_BASE + 5, au1000_ic1r1_dispatch);
+}
+
+static void __init alchemy_gpic_init_irq(const struct alchemy_irqmap *dints)
+{
+	int i;
+	void __iomem *bank_base;
+
+	register_syscore_ops(&alchemy_gpic_pmops);
+	mips_cpu_irq_init();
+
+	/* disable & ack all possible interrupt sources */
+	for (i = 0; i < 4; i++) {
+		bank_base = AU1300_GPIC_ADDR + (i * 4);
+		__raw_writel(~0UL, bank_base + AU1300_GPIC_IDIS);
+		wmb();
+		__raw_writel(~0UL, bank_base + AU1300_GPIC_IPEND);
+		wmb();
+	}
+
+	/* register an irq_chip for them, with 2nd highest priority */
+	for (i = ALCHEMY_GPIC_INT_BASE; i <= ALCHEMY_GPIC_INT_LAST; i++) {
+		au1300_set_irq_priority(i, 1);
+		au1300_gpic_settype(irq_get_irq_data(i), IRQ_TYPE_NONE);
+	}
+
+	/* setup known on-chip sources */
+	while ((i = dints->irq) != -1) {
+		au1300_gpic_settype(irq_get_irq_data(i), dints->type);
+		au1300_set_irq_priority(i, dints->prio);
+
+		if (dints->internal)
+			au1300_pinfunc_to_dev(i - ALCHEMY_GPIC_INT_BASE);
+
+		dints++;
+	}
+
+	irq_set_chained_handler(MIPS_CPU_IRQ_BASE + 2, alchemy_gpic_dispatch);
+	irq_set_chained_handler(MIPS_CPU_IRQ_BASE + 3, alchemy_gpic_dispatch);
+	irq_set_chained_handler(MIPS_CPU_IRQ_BASE + 4, alchemy_gpic_dispatch);
+	irq_set_chained_handler(MIPS_CPU_IRQ_BASE + 5, alchemy_gpic_dispatch);
+}
+
+/******************************************************************************/
+
+void __init arch_init_irq(void)
+{
+	switch (alchemy_get_cputype()) {
+	case ALCHEMY_CPU_AU1000:
+		au1000_init_irq(au1000_irqmap);
+		break;
+	case ALCHEMY_CPU_AU1500:
+		au1000_init_irq(au1500_irqmap);
+		break;
+	case ALCHEMY_CPU_AU1100:
+		au1000_init_irq(au1100_irqmap);
+		break;
+	case ALCHEMY_CPU_AU1550:
+		au1000_init_irq(au1550_irqmap);
+		break;
+	case ALCHEMY_CPU_AU1200:
+		au1000_init_irq(au1200_irqmap);
+		break;
+	case ALCHEMY_CPU_AU1300:
+		alchemy_gpic_init_irq(au1300_irqmap);
+		break;
+	default:
+		pr_err("unknown Alchemy IRQ core\n");
+		break;
+	}
+}
+
+asmlinkage void plat_irq_dispatch(void)
+{
+	unsigned long r = (read_c0_status() & read_c0_cause()) >> 8;
+	do_IRQ(MIPS_CPU_IRQ_BASE + __ffs(r & 0xff));
+}
diff --git a/arch/mips/alchemy/common/platform.c b/arch/mips/alchemy/common/platform.c
new file mode 100644
index 000000000..b8f3397c5
--- /dev/null
+++ b/arch/mips/alchemy/common/platform.c
@@ -0,0 +1,458 @@
+/*
+ * Platform device support for Au1x00 SoCs.
+ *
+ * Copyright 2004, Matt Porter <mporter@kernel.crashing.org>
+ *
+ * (C) Copyright Embedded Alley Solutions, Inc 2005
+ * Author: Pantelis Antoniou <pantelis@embeddedalley.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/clk.h>
+#include <linux/dma-mapping.h>
+#include <linux/etherdevice.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/serial_8250.h>
+#include <linux/slab.h>
+#include <linux/usb/ehci_pdriver.h>
+#include <linux/usb/ohci_pdriver.h>
+
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1xxx_dbdma.h>
+#include <asm/mach-au1x00/au1100_mmc.h>
+#include <asm/mach-au1x00/au1xxx_eth.h>
+
+#include <prom.h>
+
+static void alchemy_8250_pm(struct uart_port *port, unsigned int state,
+			    unsigned int old_state)
+{
+#ifdef CONFIG_SERIAL_8250
+	switch (state) {
+	case 0:
+		alchemy_uart_enable(CPHYSADDR(port->membase));
+		serial8250_do_pm(port, state, old_state);
+		break;
+	case 3:		/* power off */
+		serial8250_do_pm(port, state, old_state);
+		alchemy_uart_disable(CPHYSADDR(port->membase));
+		break;
+	default:
+		serial8250_do_pm(port, state, old_state);
+		break;
+	}
+#endif
+}
+
+#define PORT(_base, _irq)					\
+	{							\
+		.mapbase	= _base,			\
+		.irq		= _irq,				\
+		.regshift	= 2,				\
+		.iotype		= UPIO_AU,			\
+		.flags		= UPF_SKIP_TEST | UPF_IOREMAP | \
+				  UPF_FIXED_TYPE,		\
+		.type		= PORT_16550A,			\
+		.pm		= alchemy_8250_pm,		\
+	}
+
+static struct plat_serial8250_port au1x00_uart_data[][4] __initdata = {
+	[ALCHEMY_CPU_AU1000] = {
+		PORT(AU1000_UART0_PHYS_ADDR, AU1000_UART0_INT),
+		PORT(AU1000_UART1_PHYS_ADDR, AU1000_UART1_INT),
+		PORT(AU1000_UART2_PHYS_ADDR, AU1000_UART2_INT),
+		PORT(AU1000_UART3_PHYS_ADDR, AU1000_UART3_INT),
+	},
+	[ALCHEMY_CPU_AU1500] = {
+		PORT(AU1000_UART0_PHYS_ADDR, AU1500_UART0_INT),
+		PORT(AU1000_UART3_PHYS_ADDR, AU1500_UART3_INT),
+	},
+	[ALCHEMY_CPU_AU1100] = {
+		PORT(AU1000_UART0_PHYS_ADDR, AU1100_UART0_INT),
+		PORT(AU1000_UART1_PHYS_ADDR, AU1100_UART1_INT),
+		PORT(AU1000_UART3_PHYS_ADDR, AU1100_UART3_INT),
+	},
+	[ALCHEMY_CPU_AU1550] = {
+		PORT(AU1000_UART0_PHYS_ADDR, AU1550_UART0_INT),
+		PORT(AU1000_UART1_PHYS_ADDR, AU1550_UART1_INT),
+		PORT(AU1000_UART3_PHYS_ADDR, AU1550_UART3_INT),
+	},
+	[ALCHEMY_CPU_AU1200] = {
+		PORT(AU1000_UART0_PHYS_ADDR, AU1200_UART0_INT),
+		PORT(AU1000_UART1_PHYS_ADDR, AU1200_UART1_INT),
+	},
+	[ALCHEMY_CPU_AU1300] = {
+		PORT(AU1300_UART0_PHYS_ADDR, AU1300_UART0_INT),
+		PORT(AU1300_UART1_PHYS_ADDR, AU1300_UART1_INT),
+		PORT(AU1300_UART2_PHYS_ADDR, AU1300_UART2_INT),
+		PORT(AU1300_UART3_PHYS_ADDR, AU1300_UART3_INT),
+	},
+};
+
+static struct platform_device au1xx0_uart_device = {
+	.name			= "serial8250",
+	.id			= PLAT8250_DEV_AU1X00,
+};
+
+static void __init alchemy_setup_uarts(int ctype)
+{
+	long uartclk;
+	int s = sizeof(struct plat_serial8250_port);
+	int c = alchemy_get_uarts(ctype);
+	struct plat_serial8250_port *ports;
+	struct clk *clk = clk_get(NULL, ALCHEMY_PERIPH_CLK);
+
+	if (IS_ERR(clk))
+		return;
+	if (clk_prepare_enable(clk)) {
+		clk_put(clk);
+		return;
+	}
+	uartclk = clk_get_rate(clk);
+	clk_put(clk);
+
+	ports = kcalloc(s, (c + 1), GFP_KERNEL);
+	if (!ports) {
+		printk(KERN_INFO "Alchemy: no memory for UART data\n");
+		return;
+	}
+	memcpy(ports, au1x00_uart_data[ctype], s * c);
+	au1xx0_uart_device.dev.platform_data = ports;
+
+	/* Fill up uartclk. */
+	for (s = 0; s < c; s++)
+		ports[s].uartclk = uartclk;
+	if (platform_device_register(&au1xx0_uart_device))
+		printk(KERN_INFO "Alchemy: failed to register UARTs\n");
+}
+
+
+static u64 alchemy_all_dmamask = DMA_BIT_MASK(32);
+
+/* Power on callback for the ehci platform driver */
+static int alchemy_ehci_power_on(struct platform_device *pdev)
+{
+	return alchemy_usb_control(ALCHEMY_USB_EHCI0, 1);
+}
+
+/* Power off/suspend callback for the ehci platform driver */
+static void alchemy_ehci_power_off(struct platform_device *pdev)
+{
+	alchemy_usb_control(ALCHEMY_USB_EHCI0, 0);
+}
+
+static struct usb_ehci_pdata alchemy_ehci_pdata = {
+	.no_io_watchdog = 1,
+	.power_on	= alchemy_ehci_power_on,
+	.power_off	= alchemy_ehci_power_off,
+	.power_suspend	= alchemy_ehci_power_off,
+};
+
+/* Power on callback for the ohci platform driver */
+static int alchemy_ohci_power_on(struct platform_device *pdev)
+{
+	int unit;
+
+	unit = (pdev->id == 1) ?
+		ALCHEMY_USB_OHCI1 : ALCHEMY_USB_OHCI0;
+
+	return alchemy_usb_control(unit, 1);
+}
+
+/* Power off/suspend callback for the ohci platform driver */
+static void alchemy_ohci_power_off(struct platform_device *pdev)
+{
+	int unit;
+
+	unit = (pdev->id == 1) ?
+		ALCHEMY_USB_OHCI1 : ALCHEMY_USB_OHCI0;
+
+	alchemy_usb_control(unit, 0);
+}
+
+static struct usb_ohci_pdata alchemy_ohci_pdata = {
+	.power_on		= alchemy_ohci_power_on,
+	.power_off		= alchemy_ohci_power_off,
+	.power_suspend		= alchemy_ohci_power_off,
+};
+
+static unsigned long alchemy_ohci_data[][2] __initdata = {
+	[ALCHEMY_CPU_AU1000] = { AU1000_USB_OHCI_PHYS_ADDR, AU1000_USB_HOST_INT },
+	[ALCHEMY_CPU_AU1500] = { AU1000_USB_OHCI_PHYS_ADDR, AU1500_USB_HOST_INT },
+	[ALCHEMY_CPU_AU1100] = { AU1000_USB_OHCI_PHYS_ADDR, AU1100_USB_HOST_INT },
+	[ALCHEMY_CPU_AU1550] = { AU1550_USB_OHCI_PHYS_ADDR, AU1550_USB_HOST_INT },
+	[ALCHEMY_CPU_AU1200] = { AU1200_USB_OHCI_PHYS_ADDR, AU1200_USB_INT },
+	[ALCHEMY_CPU_AU1300] = { AU1300_USB_OHCI0_PHYS_ADDR, AU1300_USB_INT },
+};
+
+static unsigned long alchemy_ehci_data[][2] __initdata = {
+	[ALCHEMY_CPU_AU1200] = { AU1200_USB_EHCI_PHYS_ADDR, AU1200_USB_INT },
+	[ALCHEMY_CPU_AU1300] = { AU1300_USB_EHCI_PHYS_ADDR, AU1300_USB_INT },
+};
+
+static int __init _new_usbres(struct resource **r, struct platform_device **d)
+{
+	*r = kcalloc(2, sizeof(struct resource), GFP_KERNEL);
+	if (!*r)
+		return -ENOMEM;
+	*d = kzalloc(sizeof(struct platform_device), GFP_KERNEL);
+	if (!*d) {
+		kfree(*r);
+		return -ENOMEM;
+	}
+
+	(*d)->dev.coherent_dma_mask = DMA_BIT_MASK(32);
+	(*d)->num_resources = 2;
+	(*d)->resource = *r;
+
+	return 0;
+}
+
+static void __init alchemy_setup_usb(int ctype)
+{
+	struct resource *res;
+	struct platform_device *pdev;
+
+	/* setup OHCI0.  Every variant has one */
+	if (_new_usbres(&res, &pdev))
+		return;
+
+	res[0].start = alchemy_ohci_data[ctype][0];
+	res[0].end = res[0].start + 0x100 - 1;
+	res[0].flags = IORESOURCE_MEM;
+	res[1].start = alchemy_ohci_data[ctype][1];
+	res[1].end = res[1].start;
+	res[1].flags = IORESOURCE_IRQ;
+	pdev->name = "ohci-platform";
+	pdev->id = 0;
+	pdev->dev.dma_mask = &alchemy_all_dmamask;
+	pdev->dev.platform_data = &alchemy_ohci_pdata;
+
+	if (platform_device_register(pdev))
+		printk(KERN_INFO "Alchemy USB: cannot add OHCI0\n");
+
+
+	/* setup EHCI0: Au1200/Au1300 */
+	if ((ctype == ALCHEMY_CPU_AU1200) || (ctype == ALCHEMY_CPU_AU1300)) {
+		if (_new_usbres(&res, &pdev))
+			return;
+
+		res[0].start = alchemy_ehci_data[ctype][0];
+		res[0].end = res[0].start + 0x100 - 1;
+		res[0].flags = IORESOURCE_MEM;
+		res[1].start = alchemy_ehci_data[ctype][1];
+		res[1].end = res[1].start;
+		res[1].flags = IORESOURCE_IRQ;
+		pdev->name = "ehci-platform";
+		pdev->id = 0;
+		pdev->dev.dma_mask = &alchemy_all_dmamask;
+		pdev->dev.platform_data = &alchemy_ehci_pdata;
+
+		if (platform_device_register(pdev))
+			printk(KERN_INFO "Alchemy USB: cannot add EHCI0\n");
+	}
+
+	/* Au1300: OHCI1 */
+	if (ctype == ALCHEMY_CPU_AU1300) {
+		if (_new_usbres(&res, &pdev))
+			return;
+
+		res[0].start = AU1300_USB_OHCI1_PHYS_ADDR;
+		res[0].end = res[0].start + 0x100 - 1;
+		res[0].flags = IORESOURCE_MEM;
+		res[1].start = AU1300_USB_INT;
+		res[1].end = res[1].start;
+		res[1].flags = IORESOURCE_IRQ;
+		pdev->name = "ohci-platform";
+		pdev->id = 1;
+		pdev->dev.dma_mask = &alchemy_all_dmamask;
+		pdev->dev.platform_data = &alchemy_ohci_pdata;
+
+		if (platform_device_register(pdev))
+			printk(KERN_INFO "Alchemy USB: cannot add OHCI1\n");
+	}
+}
+
+/* Macro to help defining the Ethernet MAC resources */
+#define MAC_RES_COUNT	4	/* MAC regs, MAC en, MAC INT, MACDMA regs */
+#define MAC_RES(_base, _enable, _irq, _macdma)		\
+	{						\
+		.start	= _base,			\
+		.end	= _base + 0xffff,		\
+		.flags	= IORESOURCE_MEM,		\
+	},						\
+	{						\
+		.start	= _enable,			\
+		.end	= _enable + 0x3,		\
+		.flags	= IORESOURCE_MEM,		\
+	},						\
+	{						\
+		.start	= _irq,				\
+		.end	= _irq,				\
+		.flags	= IORESOURCE_IRQ		\
+	},						\
+	{						\
+		.start	= _macdma,			\
+		.end	= _macdma + 0x1ff,		\
+		.flags	= IORESOURCE_MEM,		\
+	}
+
+static struct resource au1xxx_eth0_resources[][MAC_RES_COUNT] __initdata = {
+	[ALCHEMY_CPU_AU1000] = {
+		MAC_RES(AU1000_MAC0_PHYS_ADDR,
+			AU1000_MACEN_PHYS_ADDR,
+			AU1000_MAC0_DMA_INT,
+			AU1000_MACDMA0_PHYS_ADDR)
+	},
+	[ALCHEMY_CPU_AU1500] = {
+		MAC_RES(AU1500_MAC0_PHYS_ADDR,
+			AU1500_MACEN_PHYS_ADDR,
+			AU1500_MAC0_DMA_INT,
+			AU1000_MACDMA0_PHYS_ADDR)
+	},
+	[ALCHEMY_CPU_AU1100] = {
+		MAC_RES(AU1000_MAC0_PHYS_ADDR,
+			AU1000_MACEN_PHYS_ADDR,
+			AU1100_MAC0_DMA_INT,
+			AU1000_MACDMA0_PHYS_ADDR)
+	},
+	[ALCHEMY_CPU_AU1550] = {
+		MAC_RES(AU1000_MAC0_PHYS_ADDR,
+			AU1000_MACEN_PHYS_ADDR,
+			AU1550_MAC0_DMA_INT,
+			AU1000_MACDMA0_PHYS_ADDR)
+	},
+};
+
+static struct au1000_eth_platform_data au1xxx_eth0_platform_data = {
+	.phy1_search_mac0 = 1,
+};
+
+static struct platform_device au1xxx_eth0_device = {
+	.name		= "au1000-eth",
+	.id		= 0,
+	.num_resources	= MAC_RES_COUNT,
+	.dev = {
+		.dma_mask               = &alchemy_all_dmamask,
+		.coherent_dma_mask      = DMA_BIT_MASK(32),
+		.platform_data          = &au1xxx_eth0_platform_data,
+	},
+};
+
+static struct resource au1xxx_eth1_resources[][MAC_RES_COUNT] __initdata = {
+	[ALCHEMY_CPU_AU1000] = {
+		MAC_RES(AU1000_MAC1_PHYS_ADDR,
+			AU1000_MACEN_PHYS_ADDR + 4,
+			AU1000_MAC1_DMA_INT,
+			AU1000_MACDMA1_PHYS_ADDR)
+	},
+	[ALCHEMY_CPU_AU1500] = {
+		MAC_RES(AU1500_MAC1_PHYS_ADDR,
+			AU1500_MACEN_PHYS_ADDR + 4,
+			AU1500_MAC1_DMA_INT,
+			AU1000_MACDMA1_PHYS_ADDR)
+	},
+	[ALCHEMY_CPU_AU1550] = {
+		MAC_RES(AU1000_MAC1_PHYS_ADDR,
+			AU1000_MACEN_PHYS_ADDR + 4,
+			AU1550_MAC1_DMA_INT,
+			AU1000_MACDMA1_PHYS_ADDR)
+	},
+};
+
+static struct au1000_eth_platform_data au1xxx_eth1_platform_data = {
+	.phy1_search_mac0 = 1,
+};
+
+static struct platform_device au1xxx_eth1_device = {
+	.name		= "au1000-eth",
+	.id		= 1,
+	.num_resources	= MAC_RES_COUNT,
+	.dev = {
+		.dma_mask               = &alchemy_all_dmamask,
+		.coherent_dma_mask      = DMA_BIT_MASK(32),
+		.platform_data          = &au1xxx_eth1_platform_data,
+	},
+};
+
+void __init au1xxx_override_eth_cfg(unsigned int port,
+			struct au1000_eth_platform_data *eth_data)
+{
+	if (!eth_data || port > 1)
+		return;
+
+	if (port == 0)
+		memcpy(&au1xxx_eth0_platform_data, eth_data,
+			sizeof(struct au1000_eth_platform_data));
+	else
+		memcpy(&au1xxx_eth1_platform_data, eth_data,
+			sizeof(struct au1000_eth_platform_data));
+}
+
+static void __init alchemy_setup_macs(int ctype)
+{
+	int ret, i;
+	unsigned char ethaddr[6];
+	struct resource *macres;
+
+	/* Handle 1st MAC */
+	if (alchemy_get_macs(ctype) < 1)
+		return;
+
+	macres = kmemdup(au1xxx_eth0_resources[ctype],
+			 sizeof(struct resource) * MAC_RES_COUNT, GFP_KERNEL);
+	if (!macres) {
+		printk(KERN_INFO "Alchemy: no memory for MAC0 resources\n");
+		return;
+	}
+	au1xxx_eth0_device.resource = macres;
+
+	i = prom_get_ethernet_addr(ethaddr);
+	if (!i && !is_valid_ether_addr(au1xxx_eth0_platform_data.mac))
+		memcpy(au1xxx_eth0_platform_data.mac, ethaddr, 6);
+
+	ret = platform_device_register(&au1xxx_eth0_device);
+	if (ret)
+		printk(KERN_INFO "Alchemy: failed to register MAC0\n");
+
+
+	/* Handle 2nd MAC */
+	if (alchemy_get_macs(ctype) < 2)
+		return;
+
+	macres = kmemdup(au1xxx_eth1_resources[ctype],
+			 sizeof(struct resource) * MAC_RES_COUNT, GFP_KERNEL);
+	if (!macres) {
+		printk(KERN_INFO "Alchemy: no memory for MAC1 resources\n");
+		return;
+	}
+	au1xxx_eth1_device.resource = macres;
+
+	ethaddr[5] += 1;	/* next addr for 2nd MAC */
+	if (!i && !is_valid_ether_addr(au1xxx_eth1_platform_data.mac))
+		memcpy(au1xxx_eth1_platform_data.mac, ethaddr, 6);
+
+	/* Register second MAC if enabled in pinfunc */
+	if (!(alchemy_rdsys(AU1000_SYS_PINFUNC) & SYS_PF_NI2)) {
+		ret = platform_device_register(&au1xxx_eth1_device);
+		if (ret)
+			printk(KERN_INFO "Alchemy: failed to register MAC1\n");
+	}
+}
+
+static int __init au1xxx_platform_init(void)
+{
+	int ctype = alchemy_get_cputype();
+
+	alchemy_setup_uarts(ctype);
+	alchemy_setup_macs(ctype);
+	alchemy_setup_usb(ctype);
+
+	return 0;
+}
+
+arch_initcall(au1xxx_platform_init);
diff --git a/arch/mips/alchemy/common/power.c b/arch/mips/alchemy/common/power.c
new file mode 100644
index 000000000..303257b69
--- /dev/null
+++ b/arch/mips/alchemy/common/power.c
@@ -0,0 +1,132 @@
+/*
+ * BRIEF MODULE DESCRIPTION
+ *	Au1xx0 Power Management routines.
+ *
+ * Copyright 2001, 2008 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc. <source@mvista.com>
+ *
+ *  Some of the routines are right out of init/main.c, whose
+ *  copyrights apply here.
+ *
+ *  This program is free software; you can redistribute	 it and/or modify it
+ *  under  the terms of	 the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the	License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED	  ``AS	IS'' AND   ANY	EXPRESS OR IMPLIED
+ *  WARRANTIES,	  INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO	EVENT  SHALL   THE AUTHOR  BE	 LIABLE FOR ANY	  DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED	  TO, PROCUREMENT OF  SUBSTITUTE GOODS	OR SERVICES; LOSS OF
+ *  USE, DATA,	OR PROFITS; OR	BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN	 CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/pm.h>
+#include <linux/sysctl.h>
+#include <linux/jiffies.h>
+
+#include <linux/uaccess.h>
+#include <asm/mach-au1x00/au1000.h>
+
+/*
+ * We need to save/restore a bunch of core registers that are
+ * either volatile or reset to some state across a processor sleep.
+ * If reading a register doesn't provide a proper result for a
+ * later restore, we have to provide a function for loading that
+ * register and save a copy.
+ *
+ * We only have to save/restore registers that aren't otherwise
+ * done as part of a driver pm_* function.
+ */
+static unsigned int sleep_sys_clocks[5];
+static unsigned int sleep_sys_pinfunc;
+static unsigned int sleep_static_memctlr[4][3];
+
+
+static void save_core_regs(void)
+{
+	/* Clocks and PLLs. */
+	sleep_sys_clocks[0] = alchemy_rdsys(AU1000_SYS_FREQCTRL0);
+	sleep_sys_clocks[1] = alchemy_rdsys(AU1000_SYS_FREQCTRL1);
+	sleep_sys_clocks[2] = alchemy_rdsys(AU1000_SYS_CLKSRC);
+	sleep_sys_clocks[3] = alchemy_rdsys(AU1000_SYS_CPUPLL);
+	sleep_sys_clocks[4] = alchemy_rdsys(AU1000_SYS_AUXPLL);
+
+	/* pin mux config */
+	sleep_sys_pinfunc = alchemy_rdsys(AU1000_SYS_PINFUNC);
+
+	/* Save the static memory controller configuration. */
+	sleep_static_memctlr[0][0] = alchemy_rdsmem(AU1000_MEM_STCFG0);
+	sleep_static_memctlr[0][1] = alchemy_rdsmem(AU1000_MEM_STTIME0);
+	sleep_static_memctlr[0][2] = alchemy_rdsmem(AU1000_MEM_STADDR0);
+	sleep_static_memctlr[1][0] = alchemy_rdsmem(AU1000_MEM_STCFG1);
+	sleep_static_memctlr[1][1] = alchemy_rdsmem(AU1000_MEM_STTIME1);
+	sleep_static_memctlr[1][2] = alchemy_rdsmem(AU1000_MEM_STADDR1);
+	sleep_static_memctlr[2][0] = alchemy_rdsmem(AU1000_MEM_STCFG2);
+	sleep_static_memctlr[2][1] = alchemy_rdsmem(AU1000_MEM_STTIME2);
+	sleep_static_memctlr[2][2] = alchemy_rdsmem(AU1000_MEM_STADDR2);
+	sleep_static_memctlr[3][0] = alchemy_rdsmem(AU1000_MEM_STCFG3);
+	sleep_static_memctlr[3][1] = alchemy_rdsmem(AU1000_MEM_STTIME3);
+	sleep_static_memctlr[3][2] = alchemy_rdsmem(AU1000_MEM_STADDR3);
+}
+
+static void restore_core_regs(void)
+{
+	/* restore clock configuration.  Writing CPUPLL last will
+	 * stall a bit and stabilize other clocks (unless this is
+	 * one of those Au1000 with a write-only PLL, where we dont
+	 * have a valid value)
+	 */
+	alchemy_wrsys(sleep_sys_clocks[0], AU1000_SYS_FREQCTRL0);
+	alchemy_wrsys(sleep_sys_clocks[1], AU1000_SYS_FREQCTRL1);
+	alchemy_wrsys(sleep_sys_clocks[2], AU1000_SYS_CLKSRC);
+	alchemy_wrsys(sleep_sys_clocks[4], AU1000_SYS_AUXPLL);
+	if (!au1xxx_cpu_has_pll_wo())
+		alchemy_wrsys(sleep_sys_clocks[3], AU1000_SYS_CPUPLL);
+
+	alchemy_wrsys(sleep_sys_pinfunc, AU1000_SYS_PINFUNC);
+
+	/* Restore the static memory controller configuration. */
+	alchemy_wrsmem(sleep_static_memctlr[0][0], AU1000_MEM_STCFG0);
+	alchemy_wrsmem(sleep_static_memctlr[0][1], AU1000_MEM_STTIME0);
+	alchemy_wrsmem(sleep_static_memctlr[0][2], AU1000_MEM_STADDR0);
+	alchemy_wrsmem(sleep_static_memctlr[1][0], AU1000_MEM_STCFG1);
+	alchemy_wrsmem(sleep_static_memctlr[1][1], AU1000_MEM_STTIME1);
+	alchemy_wrsmem(sleep_static_memctlr[1][2], AU1000_MEM_STADDR1);
+	alchemy_wrsmem(sleep_static_memctlr[2][0], AU1000_MEM_STCFG2);
+	alchemy_wrsmem(sleep_static_memctlr[2][1], AU1000_MEM_STTIME2);
+	alchemy_wrsmem(sleep_static_memctlr[2][2], AU1000_MEM_STADDR2);
+	alchemy_wrsmem(sleep_static_memctlr[3][0], AU1000_MEM_STCFG3);
+	alchemy_wrsmem(sleep_static_memctlr[3][1], AU1000_MEM_STTIME3);
+	alchemy_wrsmem(sleep_static_memctlr[3][2], AU1000_MEM_STADDR3);
+}
+
+void au_sleep(void)
+{
+	save_core_regs();
+
+	switch (alchemy_get_cputype()) {
+	case ALCHEMY_CPU_AU1000:
+	case ALCHEMY_CPU_AU1500:
+	case ALCHEMY_CPU_AU1100:
+		alchemy_sleep_au1000();
+		break;
+	case ALCHEMY_CPU_AU1550:
+	case ALCHEMY_CPU_AU1200:
+		alchemy_sleep_au1550();
+		break;
+	case ALCHEMY_CPU_AU1300:
+		alchemy_sleep_au1300();
+		break;
+	}
+
+	restore_core_regs();
+}
diff --git a/arch/mips/alchemy/common/prom.c b/arch/mips/alchemy/common/prom.c
new file mode 100644
index 000000000..b13d8adf3
--- /dev/null
+++ b/arch/mips/alchemy/common/prom.c
@@ -0,0 +1,145 @@
+/*
+ *
+ * BRIEF MODULE DESCRIPTION
+ *    PROM library initialisation code, supports YAMON and U-Boot.
+ *
+ * Copyright 2000-2001, 2006, 2008 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc. <source@mvista.com>
+ *
+ * This file was derived from Carsten Langgaard's
+ * arch/mips/mips-boards/xx files.
+ *
+ * Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 1999,2000 MIPS Technologies, Inc.  All rights reserved.
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/memblock.h>
+#include <linux/sizes.h>
+#include <linux/string.h>
+
+#include <asm/bootinfo.h>
+
+int prom_argc;
+char **prom_argv;
+char **prom_envp;
+
+void __init prom_init_cmdline(void)
+{
+	int i;
+
+	for (i = 1; i < prom_argc; i++) {
+		strlcat(arcs_cmdline, prom_argv[i], COMMAND_LINE_SIZE);
+		if (i < (prom_argc - 1))
+			strlcat(arcs_cmdline, " ", COMMAND_LINE_SIZE);
+	}
+}
+
+char *prom_getenv(char *envname)
+{
+	/*
+	 * Return a pointer to the given environment variable.
+	 * YAMON uses "name", "value" pairs, while U-Boot uses "name=value".
+	 */
+
+	char **env = prom_envp;
+	int i = strlen(envname);
+	int yamon = (*env && strchr(*env, '=') == NULL);
+
+	while (*env) {
+		if (yamon) {
+			if (strcmp(envname, *env++) == 0)
+				return *env;
+		} else if (strncmp(envname, *env, i) == 0 && (*env)[i] == '=')
+			return *env + i + 1;
+		env++;
+	}
+
+	return NULL;
+}
+
+void __init prom_init(void)
+{
+	unsigned char *memsize_str;
+	unsigned long memsize;
+
+	prom_argc = (int)fw_arg0;
+	prom_argv = (char **)fw_arg1;
+	prom_envp = (char **)fw_arg2;
+
+	prom_init_cmdline();
+
+	memsize_str = prom_getenv("memsize");
+	if (!memsize_str || kstrtoul(memsize_str, 0, &memsize))
+		memsize = SZ_64M; /* minimum memsize is 64MB RAM */
+
+	memblock_add(0, memsize);
+}
+
+static inline unsigned char str2hexnum(unsigned char c)
+{
+	if (c >= '0' && c <= '9')
+		return c - '0';
+	if (c >= 'a' && c <= 'f')
+		return c - 'a' + 10;
+	if (c >= 'A' && c <= 'F')
+		return c - 'A' + 10;
+
+	return 0; /* foo */
+}
+
+static inline void str2eaddr(unsigned char *ea, unsigned char *str)
+{
+	int i;
+
+	for (i = 0; i < 6; i++) {
+		unsigned char num;
+
+		if ((*str == '.') || (*str == ':'))
+			str++;
+		num  = str2hexnum(*str++) << 4;
+		num |= str2hexnum(*str++);
+		ea[i] = num;
+	}
+}
+
+int __init prom_get_ethernet_addr(char *ethernet_addr)
+{
+	char *ethaddr_str;
+
+	/* Check the environment variables first */
+	ethaddr_str = prom_getenv("ethaddr");
+	if (!ethaddr_str) {
+		/* Check command line */
+		ethaddr_str = strstr(arcs_cmdline, "ethaddr=");
+		if (!ethaddr_str)
+			return -1;
+
+		ethaddr_str += strlen("ethaddr=");
+	}
+
+	str2eaddr(ethernet_addr, ethaddr_str);
+
+	return 0;
+}
diff --git a/arch/mips/alchemy/common/setup.c b/arch/mips/alchemy/common/setup.c
new file mode 100644
index 000000000..2388d6878
--- /dev/null
+++ b/arch/mips/alchemy/common/setup.c
@@ -0,0 +1,107 @@
+/*
+ * Copyright 2000, 2007-2008 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc. <source@mvista.com
+ *
+ * Updates to 2.6, Pete Popov, Embedded Alley Solutions, Inc.
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/init.h>
+#include <linux/ioport.h>
+#include <linux/mm.h>
+#include <linux/dma-map-ops.h> /* for dma_default_coherent */
+
+#include <asm/mipsregs.h>
+
+#include <au1000.h>
+
+extern void __init board_setup(void);
+extern void __init alchemy_set_lpj(void);
+
+static bool alchemy_dma_coherent(void)
+{
+	switch (alchemy_get_cputype()) {
+	case ALCHEMY_CPU_AU1000:
+	case ALCHEMY_CPU_AU1500:
+	case ALCHEMY_CPU_AU1100:
+		return false;
+	case ALCHEMY_CPU_AU1200:
+		/* Au1200 AB USB does not support coherent memory */
+		if ((read_c0_prid() & PRID_REV_MASK) == 0)
+			return false;
+		return true;
+	default:
+		return true;
+	}
+}
+
+void __init plat_mem_setup(void)
+{
+	alchemy_set_lpj();
+
+	if (au1xxx_cpu_needs_config_od())
+		/* Various early Au1xx0 errata corrected by this */
+		set_c0_config(1 << 19); /* Set Config[OD] */
+	else
+		/* Clear to obtain best system bus performance */
+		clear_c0_config(1 << 19); /* Clear Config[OD] */
+
+	dma_default_coherent = alchemy_dma_coherent();
+
+	board_setup();	/* board specific setup */
+
+	/* IO/MEM resources. */
+	set_io_port_base(0);
+	ioport_resource.start = IOPORT_RESOURCE_START;
+	ioport_resource.end = IOPORT_RESOURCE_END;
+	iomem_resource.start = IOMEM_RESOURCE_START;
+	iomem_resource.end = IOMEM_RESOURCE_END;
+}
+
+#ifdef CONFIG_MIPS_FIXUP_BIGPHYS_ADDR
+/* This routine should be valid for all Au1x based boards */
+phys_addr_t fixup_bigphys_addr(phys_addr_t phys_addr, phys_addr_t size)
+{
+	unsigned long start = ALCHEMY_PCI_MEMWIN_START;
+	unsigned long end = ALCHEMY_PCI_MEMWIN_END;
+
+	/* Don't fixup 36-bit addresses */
+	if ((phys_addr >> 32) != 0)
+		return phys_addr;
+
+	/* Check for PCI memory window */
+	if (phys_addr >= start && (phys_addr + size - 1) <= end)
+		return (phys_addr_t)(AU1500_PCI_MEM_PHYS_ADDR + phys_addr);
+
+	/* default nop */
+	return phys_addr;
+}
+
+int io_remap_pfn_range(struct vm_area_struct *vma, unsigned long vaddr,
+		unsigned long pfn, unsigned long size, pgprot_t prot)
+{
+	phys_addr_t phys_addr = fixup_bigphys_addr(pfn << PAGE_SHIFT, size);
+
+	return remap_pfn_range(vma, vaddr, phys_addr >> PAGE_SHIFT, size, prot);
+}
+EXPORT_SYMBOL(io_remap_pfn_range);
+#endif /* CONFIG_MIPS_FIXUP_BIGPHYS_ADDR */
diff --git a/arch/mips/alchemy/common/sleeper.S b/arch/mips/alchemy/common/sleeper.S
new file mode 100644
index 000000000..13586d224
--- /dev/null
+++ b/arch/mips/alchemy/common/sleeper.S
@@ -0,0 +1,266 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright 2002 Embedded Edge, LLC
+ * Author: dan@embeddededge.com
+ *
+ * Sleep helper for Au1xxx sleep mode.
+ */
+
+#include <asm/asm.h>
+#include <asm/mipsregs.h>
+#include <asm/regdef.h>
+#include <asm/stackframe.h>
+
+	.extern __flush_cache_all
+
+	.text
+	.set noreorder
+	.set noat
+	.align	5
+
+
+/* preparatory stuff */
+.macro	SETUP_SLEEP
+	subu	sp, PT_SIZE
+	sw	$1, PT_R1(sp)
+	sw	$2, PT_R2(sp)
+	sw	$3, PT_R3(sp)
+	sw	$4, PT_R4(sp)
+	sw	$5, PT_R5(sp)
+	sw	$6, PT_R6(sp)
+	sw	$7, PT_R7(sp)
+	sw	$16, PT_R16(sp)
+	sw	$17, PT_R17(sp)
+	sw	$18, PT_R18(sp)
+	sw	$19, PT_R19(sp)
+	sw	$20, PT_R20(sp)
+	sw	$21, PT_R21(sp)
+	sw	$22, PT_R22(sp)
+	sw	$23, PT_R23(sp)
+	sw	$26, PT_R26(sp)
+	sw	$27, PT_R27(sp)
+	sw	$28, PT_R28(sp)
+	sw	$30, PT_R30(sp)
+	sw	$31, PT_R31(sp)
+	mfc0	k0, CP0_STATUS
+	sw	k0, 0x20(sp)
+	mfc0	k0, CP0_CONTEXT
+	sw	k0, 0x1c(sp)
+	mfc0	k0, CP0_PAGEMASK
+	sw	k0, 0x18(sp)
+	mfc0	k0, CP0_CONFIG
+	sw	k0, 0x14(sp)
+
+	/* flush caches to make sure context is in memory */
+	la	t1, __flush_cache_all
+	lw	t0, 0(t1)
+	jalr	t0
+	 nop
+
+	/* Now set up the scratch registers so the boot rom will
+	 * return to this point upon wakeup.
+	 * sys_scratch0 : SP
+	 * sys_scratch1 : RA
+	 */
+	lui	t3, 0xb190		/* sys_xxx */
+	sw	sp, 0x0018(t3)
+	la	k0, alchemy_sleep_wakeup	/* resume path */
+	sw	k0, 0x001c(t3)
+.endm
+
+.macro	DO_SLEEP
+	/* put power supply and processor to sleep */
+	sw	zero, 0x0078(t3)	/* sys_slppwr */
+	sync
+	sw	zero, 0x007c(t3)	/* sys_sleep */
+	sync
+	nop
+	nop
+	nop
+	nop
+	nop
+	nop
+	nop
+	nop
+.endm
+
+/* sleep code for Au1000/Au1100/Au1500 memory controller type */
+LEAF(alchemy_sleep_au1000)
+
+	SETUP_SLEEP
+
+	/* cache following instructions, as memory gets put to sleep */
+	la	t0, 1f
+	.set	arch=r4000
+	cache	0x14, 0(t0)
+	cache	0x14, 32(t0)
+	cache	0x14, 64(t0)
+	cache	0x14, 96(t0)
+	.set	mips0
+
+1:	lui	a0, 0xb400		/* mem_xxx */
+	sw	zero, 0x001c(a0)	/* Precharge */
+	sync
+	sw	zero, 0x0020(a0)	/* Auto Refresh */
+	sync
+	sw	zero, 0x0030(a0)	/* Sleep */
+	sync
+
+	DO_SLEEP
+
+END(alchemy_sleep_au1000)
+
+/* sleep code for Au1550/Au1200 memory controller type */
+LEAF(alchemy_sleep_au1550)
+
+	SETUP_SLEEP
+
+	/* cache following instructions, as memory gets put to sleep */
+	la	t0, 1f
+	.set	arch=r4000
+	cache	0x14, 0(t0)
+	cache	0x14, 32(t0)
+	cache	0x14, 64(t0)
+	cache	0x14, 96(t0)
+	.set	mips0
+
+1:	lui	a0, 0xb400		/* mem_xxx */
+	sw	zero, 0x08c0(a0)	/* Precharge */
+	sync
+	sw	zero, 0x08d0(a0)	/* Self Refresh */
+	sync
+
+	/* wait for sdram to enter self-refresh mode */
+	lui	t0, 0x0100
+2:	lw	t1, 0x0850(a0)		/* mem_sdstat */
+	and	t2, t1, t0
+	beq	t2, zero, 2b
+	 nop
+
+	/* disable SDRAM clocks */
+	lui	t0, 0xcfff
+	ori	t0, t0, 0xffff
+	lw	t1, 0x0840(a0)		/* mem_sdconfiga */
+	and	t1, t0, t1		/* clear CE[1:0] */
+	sw	t1, 0x0840(a0)		/* mem_sdconfiga */
+	sync
+
+	DO_SLEEP
+
+END(alchemy_sleep_au1550)
+
+/* sleepcode for Au1300 memory controller type */
+LEAF(alchemy_sleep_au1300)
+
+	SETUP_SLEEP
+
+	/* cache following instructions, as memory gets put to sleep */
+	la	t0, 2f
+	la	t1, 4f
+	subu	t2, t1, t0
+
+	.set	arch=r4000
+
+1:	cache	0x14, 0(t0)
+	subu	t2, t2, 32
+	bgez	t2, 1b
+	 addu	t0, t0, 32
+
+	.set	mips0
+
+2:	lui	a0, 0xb400		/* mem_xxx */
+
+	/* disable all ports in mem_sdportcfga */
+	sw	zero, 0x868(a0)		/* mem_sdportcfga */
+	sync
+
+	/* disable ODT */
+	li	t0, 0x03010000
+	sw	t0, 0x08d8(a0)		/* mem_sdcmd0 */
+	sw	t0, 0x08dc(a0)		/* mem_sdcmd1 */
+	sync
+
+	/* precharge */
+	li	t0, 0x23000400
+	sw	t0, 0x08dc(a0)		/* mem_sdcmd1 */
+	sw	t0, 0x08d8(a0)		/* mem_sdcmd0 */
+	sync
+
+	/* auto refresh */
+	sw	zero, 0x08c8(a0)	/* mem_sdautoref */
+	sync
+
+	/* block access to the DDR */
+	lw	t0, 0x0848(a0)		/* mem_sdconfigb */
+	li	t1, (1 << 7 | 0x3F)
+	or	t0, t0, t1
+	sw	t0, 0x0848(a0)		/* mem_sdconfigb */
+	sync
+
+	/* issue the Self Refresh command */
+	li	t0, 0x10000000
+	sw	t0, 0x08dc(a0)		/* mem_sdcmd1 */
+	sw	t0, 0x08d8(a0)		/* mem_sdcmd0 */
+	sync
+
+	/* wait for sdram to enter self-refresh mode */
+	lui	t0, 0x0300
+3:	lw	t1, 0x0850(a0)		/* mem_sdstat */
+	and	t2, t1, t0
+	bne	t2, t0, 3b
+	 nop
+
+	/* disable SDRAM clocks */
+	li	t0, ~(3<<28)
+	lw	t1, 0x0840(a0)		/* mem_sdconfiga */
+	and	t1, t1, t0		/* clear CE[1:0] */
+	sw	t1, 0x0840(a0)		/* mem_sdconfiga */
+	sync
+
+	DO_SLEEP
+4:
+
+END(alchemy_sleep_au1300)
+
+
+	/* This is where we return upon wakeup.
+	 * Reload all of the registers and return.
+	 */
+LEAF(alchemy_sleep_wakeup)
+	lw	k0, 0x20(sp)
+	mtc0	k0, CP0_STATUS
+	lw	k0, 0x1c(sp)
+	mtc0	k0, CP0_CONTEXT
+	lw	k0, 0x18(sp)
+	mtc0	k0, CP0_PAGEMASK
+	lw	k0, 0x14(sp)
+	mtc0	k0, CP0_CONFIG
+
+	/* We need to catch the early Alchemy SOCs with
+	 * the write-only Config[OD] bit and set it back to one...
+	 */
+	jal	au1x00_fixup_config_od
+	 nop
+	lw	$1, PT_R1(sp)
+	lw	$2, PT_R2(sp)
+	lw	$3, PT_R3(sp)
+	lw	$4, PT_R4(sp)
+	lw	$5, PT_R5(sp)
+	lw	$6, PT_R6(sp)
+	lw	$7, PT_R7(sp)
+	lw	$16, PT_R16(sp)
+	lw	$17, PT_R17(sp)
+	lw	$18, PT_R18(sp)
+	lw	$19, PT_R19(sp)
+	lw	$20, PT_R20(sp)
+	lw	$21, PT_R21(sp)
+	lw	$22, PT_R22(sp)
+	lw	$23, PT_R23(sp)
+	lw	$26, PT_R26(sp)
+	lw	$27, PT_R27(sp)
+	lw	$28, PT_R28(sp)
+	lw	$30, PT_R30(sp)
+	lw	$31, PT_R31(sp)
+	jr	ra
+	 addiu	sp, PT_SIZE
+END(alchemy_sleep_wakeup)
diff --git a/arch/mips/alchemy/common/time.c b/arch/mips/alchemy/common/time.c
new file mode 100644
index 000000000..d794ffb67
--- /dev/null
+++ b/arch/mips/alchemy/common/time.c
@@ -0,0 +1,155 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2008-2009 Manuel Lauss <manuel.lauss@gmail.com>
+ *
+ * Previous incarnations were:
+ * Copyright (C) 2001, 2006, 2008 MontaVista Software, <source@mvista.com>
+ * Copied and modified Carsten Langgaard's time.c
+ *
+ * Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 1999,2000 MIPS Technologies, Inc.  All rights reserved.
+ *
+ * ########################################################################
+ *
+ * ########################################################################
+ *
+ * Clocksource/event using the 32.768kHz-clocked Counter1 ('RTC' in the
+ * databooks).  Firmware/Board init code must enable the counters in the
+ * counter control register, otherwise the CP0 counter clocksource/event
+ * will be installed instead (and use of 'wait' instruction is prohibited).
+ */
+
+#include <linux/clockchips.h>
+#include <linux/clocksource.h>
+#include <linux/interrupt.h>
+#include <linux/spinlock.h>
+
+#include <asm/idle.h>
+#include <asm/processor.h>
+#include <asm/time.h>
+#include <asm/mach-au1x00/au1000.h>
+
+/* 32kHz clock enabled and detected */
+#define CNTR_OK (SYS_CNTRL_E0 | SYS_CNTRL_32S)
+
+static u64 au1x_counter1_read(struct clocksource *cs)
+{
+	return alchemy_rdsys(AU1000_SYS_RTCREAD);
+}
+
+static struct clocksource au1x_counter1_clocksource = {
+	.name		= "alchemy-counter1",
+	.read		= au1x_counter1_read,
+	.mask		= CLOCKSOURCE_MASK(32),
+	.flags		= CLOCK_SOURCE_IS_CONTINUOUS,
+	.rating		= 1500,
+};
+
+static int au1x_rtcmatch2_set_next_event(unsigned long delta,
+					 struct clock_event_device *cd)
+{
+	delta += alchemy_rdsys(AU1000_SYS_RTCREAD);
+	/* wait for register access */
+	while (alchemy_rdsys(AU1000_SYS_CNTRCTRL) & SYS_CNTRL_M21)
+		;
+	alchemy_wrsys(delta, AU1000_SYS_RTCMATCH2);
+
+	return 0;
+}
+
+static irqreturn_t au1x_rtcmatch2_irq(int irq, void *dev_id)
+{
+	struct clock_event_device *cd = dev_id;
+	cd->event_handler(cd);
+	return IRQ_HANDLED;
+}
+
+static struct clock_event_device au1x_rtcmatch2_clockdev = {
+	.name		= "rtcmatch2",
+	.features	= CLOCK_EVT_FEAT_ONESHOT,
+	.rating		= 1500,
+	.set_next_event = au1x_rtcmatch2_set_next_event,
+	.cpumask	= cpu_possible_mask,
+};
+
+static int __init alchemy_time_init(unsigned int m2int)
+{
+	struct clock_event_device *cd = &au1x_rtcmatch2_clockdev;
+	unsigned long t;
+
+	au1x_rtcmatch2_clockdev.irq = m2int;
+
+	/* Check if firmware (YAMON, ...) has enabled 32kHz and clock
+	 * has been detected.  If so install the rtcmatch2 clocksource,
+	 * otherwise don't bother.  Note that both bits being set is by
+	 * no means a definite guarantee that the counters actually work
+	 * (the 32S bit seems to be stuck set to 1 once a single clock-
+	 * edge is detected, hence the timeouts).
+	 */
+	if (CNTR_OK != (alchemy_rdsys(AU1000_SYS_CNTRCTRL) & CNTR_OK))
+		goto cntr_err;
+
+	/*
+	 * setup counter 1 (RTC) to tick at full speed
+	 */
+	t = 0xffffff;
+	while ((alchemy_rdsys(AU1000_SYS_CNTRCTRL) & SYS_CNTRL_T1S) && --t)
+		asm volatile ("nop");
+	if (!t)
+		goto cntr_err;
+
+	alchemy_wrsys(0, AU1000_SYS_RTCTRIM);	/* 32.768 kHz */
+
+	t = 0xffffff;
+	while ((alchemy_rdsys(AU1000_SYS_CNTRCTRL) & SYS_CNTRL_C1S) && --t)
+		asm volatile ("nop");
+	if (!t)
+		goto cntr_err;
+	alchemy_wrsys(0, AU1000_SYS_RTCWRITE);
+
+	t = 0xffffff;
+	while ((alchemy_rdsys(AU1000_SYS_CNTRCTRL) & SYS_CNTRL_C1S) && --t)
+		asm volatile ("nop");
+	if (!t)
+		goto cntr_err;
+
+	/* register counter1 clocksource and event device */
+	clocksource_register_hz(&au1x_counter1_clocksource, 32768);
+
+	cd->shift = 32;
+	cd->mult = div_sc(32768, NSEC_PER_SEC, cd->shift);
+	cd->max_delta_ns = clockevent_delta2ns(0xffffffff, cd);
+	cd->max_delta_ticks = 0xffffffff;
+	cd->min_delta_ns = clockevent_delta2ns(9, cd);
+	cd->min_delta_ticks = 9;	/* ~0.28ms */
+	clockevents_register_device(cd);
+	if (request_irq(m2int, au1x_rtcmatch2_irq, IRQF_TIMER, "timer",
+			&au1x_rtcmatch2_clockdev))
+		pr_err("Failed to register timer interrupt\n");
+
+	printk(KERN_INFO "Alchemy clocksource installed\n");
+
+	return 0;
+
+cntr_err:
+	return -1;
+}
+
+static int alchemy_m2inttab[] __initdata = {
+	AU1000_RTC_MATCH2_INT,
+	AU1500_RTC_MATCH2_INT,
+	AU1100_RTC_MATCH2_INT,
+	AU1550_RTC_MATCH2_INT,
+	AU1200_RTC_MATCH2_INT,
+	AU1300_RTC_MATCH2_INT,
+};
+
+void __init plat_time_init(void)
+{
+	int t;
+
+	t = alchemy_get_cputype();
+	if (t == ALCHEMY_CPU_UNKNOWN ||
+	    alchemy_time_init(alchemy_m2inttab[t]))
+		cpu_wait = NULL;	/* wait doesn't work with r4k timer */
+}
diff --git a/arch/mips/alchemy/common/usb.c b/arch/mips/alchemy/common/usb.c
new file mode 100644
index 000000000..5d618547e
--- /dev/null
+++ b/arch/mips/alchemy/common/usb.c
@@ -0,0 +1,627 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * USB block power/access management abstraction.
+ *
+ * Au1000+: The OHCI block control register is at the far end of the OHCI memory
+ *	    area. Au1550 has OHCI on different base address. No need to handle
+ *	    UDC here.
+ * Au1200:  one register to control access and clocks to O/EHCI, UDC and OTG
+ *	    as well as the PHY for EHCI and UDC.
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/export.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/spinlock.h>
+#include <linux/syscore_ops.h>
+#include <asm/cpu.h>
+#include <asm/mach-au1x00/au1000.h>
+
+/* control register offsets */
+#define AU1000_OHCICFG	0x7fffc
+#define AU1550_OHCICFG	0x07ffc
+#define AU1200_USBCFG	0x04
+
+/* Au1000 USB block config bits */
+#define USBHEN_RD	(1 << 4)		/* OHCI reset-done indicator */
+#define USBHEN_CE	(1 << 3)		/* OHCI block clock enable */
+#define USBHEN_E	(1 << 2)		/* OHCI block enable */
+#define USBHEN_C	(1 << 1)		/* OHCI block coherency bit */
+#define USBHEN_BE	(1 << 0)		/* OHCI Big-Endian */
+
+/* Au1200 USB config bits */
+#define USBCFG_PFEN	(1 << 31)		/* prefetch enable (undoc) */
+#define USBCFG_RDCOMB	(1 << 30)		/* read combining (undoc) */
+#define USBCFG_UNKNOWN	(5 << 20)		/* unknown, leave this way */
+#define USBCFG_SSD	(1 << 23)		/* serial short detect en */
+#define USBCFG_PPE	(1 << 19)		/* HS PHY PLL */
+#define USBCFG_UCE	(1 << 18)		/* UDC clock enable */
+#define USBCFG_ECE	(1 << 17)		/* EHCI clock enable */
+#define USBCFG_OCE	(1 << 16)		/* OHCI clock enable */
+#define USBCFG_FLA(x)	(((x) & 0x3f) << 8)
+#define USBCFG_UCAM	(1 << 7)		/* coherent access (undoc) */
+#define USBCFG_GME	(1 << 6)		/* OTG mem access */
+#define USBCFG_DBE	(1 << 5)		/* UDC busmaster enable */
+#define USBCFG_DME	(1 << 4)		/* UDC mem enable */
+#define USBCFG_EBE	(1 << 3)		/* EHCI busmaster enable */
+#define USBCFG_EME	(1 << 2)		/* EHCI mem enable */
+#define USBCFG_OBE	(1 << 1)		/* OHCI busmaster enable */
+#define USBCFG_OME	(1 << 0)		/* OHCI mem enable */
+#define USBCFG_INIT_AU1200	(USBCFG_PFEN | USBCFG_RDCOMB | USBCFG_UNKNOWN |\
+				 USBCFG_SSD | USBCFG_FLA(0x20) | USBCFG_UCAM | \
+				 USBCFG_GME | USBCFG_DBE | USBCFG_DME |	       \
+				 USBCFG_EBE | USBCFG_EME | USBCFG_OBE |	       \
+				 USBCFG_OME)
+
+/* Au1300 USB config registers */
+#define USB_DWC_CTRL1		0x00
+#define USB_DWC_CTRL2		0x04
+#define USB_VBUS_TIMER		0x10
+#define USB_SBUS_CTRL		0x14
+#define USB_MSR_ERR		0x18
+#define USB_DWC_CTRL3		0x1C
+#define USB_DWC_CTRL4		0x20
+#define USB_OTG_STATUS		0x28
+#define USB_DWC_CTRL5		0x2C
+#define USB_DWC_CTRL6		0x30
+#define USB_DWC_CTRL7		0x34
+#define USB_PHY_STATUS		0xC0
+#define USB_INT_STATUS		0xC4
+#define USB_INT_ENABLE		0xC8
+
+#define USB_DWC_CTRL1_OTGD	0x04 /* set to DISable OTG */
+#define USB_DWC_CTRL1_HSTRS	0x02 /* set to ENable EHCI */
+#define USB_DWC_CTRL1_DCRS	0x01 /* set to ENable UDC */
+
+#define USB_DWC_CTRL2_PHY1RS	0x04 /* set to enable PHY1 */
+#define USB_DWC_CTRL2_PHY0RS	0x02 /* set to enable PHY0 */
+#define USB_DWC_CTRL2_PHYRS	0x01 /* set to enable PHY */
+
+#define USB_DWC_CTRL3_OHCI1_CKEN	(1 << 19)
+#define USB_DWC_CTRL3_OHCI0_CKEN	(1 << 18)
+#define USB_DWC_CTRL3_EHCI0_CKEN	(1 << 17)
+#define USB_DWC_CTRL3_OTG0_CKEN		(1 << 16)
+
+#define USB_SBUS_CTRL_SBCA		0x04 /* coherent access */
+
+#define USB_INTEN_FORCE			0x20
+#define USB_INTEN_PHY			0x10
+#define USB_INTEN_UDC			0x08
+#define USB_INTEN_EHCI			0x04
+#define USB_INTEN_OHCI1			0x02
+#define USB_INTEN_OHCI0			0x01
+
+static DEFINE_SPINLOCK(alchemy_usb_lock);
+
+static inline void __au1300_usb_phyctl(void __iomem *base, int enable)
+{
+	unsigned long r, s;
+
+	r = __raw_readl(base + USB_DWC_CTRL2);
+	s = __raw_readl(base + USB_DWC_CTRL3);
+
+	s &= USB_DWC_CTRL3_OHCI1_CKEN | USB_DWC_CTRL3_OHCI0_CKEN |
+		USB_DWC_CTRL3_EHCI0_CKEN | USB_DWC_CTRL3_OTG0_CKEN;
+
+	if (enable) {
+		/* simply enable all PHYs */
+		r |= USB_DWC_CTRL2_PHY1RS | USB_DWC_CTRL2_PHY0RS |
+		     USB_DWC_CTRL2_PHYRS;
+		__raw_writel(r, base + USB_DWC_CTRL2);
+		wmb();
+	} else if (!s) {
+		/* no USB block active, do disable all PHYs */
+		r &= ~(USB_DWC_CTRL2_PHY1RS | USB_DWC_CTRL2_PHY0RS |
+		       USB_DWC_CTRL2_PHYRS);
+		__raw_writel(r, base + USB_DWC_CTRL2);
+		wmb();
+	}
+}
+
+static inline void __au1300_ohci_control(void __iomem *base, int enable, int id)
+{
+	unsigned long r;
+
+	if (enable) {
+		__raw_writel(1, base + USB_DWC_CTRL7);	/* start OHCI clock */
+		wmb();
+
+		r = __raw_readl(base + USB_DWC_CTRL3);	/* enable OHCI block */
+		r |= (id == 0) ? USB_DWC_CTRL3_OHCI0_CKEN
+			       : USB_DWC_CTRL3_OHCI1_CKEN;
+		__raw_writel(r, base + USB_DWC_CTRL3);
+		wmb();
+
+		__au1300_usb_phyctl(base, enable);	/* power up the PHYs */
+
+		r = __raw_readl(base + USB_INT_ENABLE);
+		r |= (id == 0) ? USB_INTEN_OHCI0 : USB_INTEN_OHCI1;
+		__raw_writel(r, base + USB_INT_ENABLE);
+		wmb();
+
+		/* reset the OHCI start clock bit */
+		__raw_writel(0, base + USB_DWC_CTRL7);
+		wmb();
+	} else {
+		r = __raw_readl(base + USB_INT_ENABLE);
+		r &= ~((id == 0) ? USB_INTEN_OHCI0 : USB_INTEN_OHCI1);
+		__raw_writel(r, base + USB_INT_ENABLE);
+		wmb();
+
+		r = __raw_readl(base + USB_DWC_CTRL3);
+		r &= ~((id == 0) ? USB_DWC_CTRL3_OHCI0_CKEN
+				 : USB_DWC_CTRL3_OHCI1_CKEN);
+		__raw_writel(r, base + USB_DWC_CTRL3);
+		wmb();
+
+		__au1300_usb_phyctl(base, enable);
+	}
+}
+
+static inline void __au1300_ehci_control(void __iomem *base, int enable)
+{
+	unsigned long r;
+
+	if (enable) {
+		r = __raw_readl(base + USB_DWC_CTRL3);
+		r |= USB_DWC_CTRL3_EHCI0_CKEN;
+		__raw_writel(r, base + USB_DWC_CTRL3);
+		wmb();
+
+		r = __raw_readl(base + USB_DWC_CTRL1);
+		r |= USB_DWC_CTRL1_HSTRS;
+		__raw_writel(r, base + USB_DWC_CTRL1);
+		wmb();
+
+		__au1300_usb_phyctl(base, enable);
+
+		r = __raw_readl(base + USB_INT_ENABLE);
+		r |= USB_INTEN_EHCI;
+		__raw_writel(r, base + USB_INT_ENABLE);
+		wmb();
+	} else {
+		r = __raw_readl(base + USB_INT_ENABLE);
+		r &= ~USB_INTEN_EHCI;
+		__raw_writel(r, base + USB_INT_ENABLE);
+		wmb();
+
+		r = __raw_readl(base + USB_DWC_CTRL1);
+		r &= ~USB_DWC_CTRL1_HSTRS;
+		__raw_writel(r, base + USB_DWC_CTRL1);
+		wmb();
+
+		r = __raw_readl(base + USB_DWC_CTRL3);
+		r &= ~USB_DWC_CTRL3_EHCI0_CKEN;
+		__raw_writel(r, base + USB_DWC_CTRL3);
+		wmb();
+
+		__au1300_usb_phyctl(base, enable);
+	}
+}
+
+static inline void __au1300_udc_control(void __iomem *base, int enable)
+{
+	unsigned long r;
+
+	if (enable) {
+		r = __raw_readl(base + USB_DWC_CTRL1);
+		r |= USB_DWC_CTRL1_DCRS;
+		__raw_writel(r, base + USB_DWC_CTRL1);
+		wmb();
+
+		__au1300_usb_phyctl(base, enable);
+
+		r = __raw_readl(base + USB_INT_ENABLE);
+		r |= USB_INTEN_UDC;
+		__raw_writel(r, base + USB_INT_ENABLE);
+		wmb();
+	} else {
+		r = __raw_readl(base + USB_INT_ENABLE);
+		r &= ~USB_INTEN_UDC;
+		__raw_writel(r, base + USB_INT_ENABLE);
+		wmb();
+
+		r = __raw_readl(base + USB_DWC_CTRL1);
+		r &= ~USB_DWC_CTRL1_DCRS;
+		__raw_writel(r, base + USB_DWC_CTRL1);
+		wmb();
+
+		__au1300_usb_phyctl(base, enable);
+	}
+}
+
+static inline void __au1300_otg_control(void __iomem *base, int enable)
+{
+	unsigned long r;
+	if (enable) {
+		r = __raw_readl(base + USB_DWC_CTRL3);
+		r |= USB_DWC_CTRL3_OTG0_CKEN;
+		__raw_writel(r, base + USB_DWC_CTRL3);
+		wmb();
+
+		r = __raw_readl(base + USB_DWC_CTRL1);
+		r &= ~USB_DWC_CTRL1_OTGD;
+		__raw_writel(r, base + USB_DWC_CTRL1);
+		wmb();
+
+		__au1300_usb_phyctl(base, enable);
+	} else {
+		r = __raw_readl(base + USB_DWC_CTRL1);
+		r |= USB_DWC_CTRL1_OTGD;
+		__raw_writel(r, base + USB_DWC_CTRL1);
+		wmb();
+
+		r = __raw_readl(base + USB_DWC_CTRL3);
+		r &= ~USB_DWC_CTRL3_OTG0_CKEN;
+		__raw_writel(r, base + USB_DWC_CTRL3);
+		wmb();
+
+		__au1300_usb_phyctl(base, enable);
+	}
+}
+
+static inline int au1300_usb_control(int block, int enable)
+{
+	void __iomem *base =
+		(void __iomem *)KSEG1ADDR(AU1300_USB_CTL_PHYS_ADDR);
+	int ret = 0;
+
+	switch (block) {
+	case ALCHEMY_USB_OHCI0:
+		__au1300_ohci_control(base, enable, 0);
+		break;
+	case ALCHEMY_USB_OHCI1:
+		__au1300_ohci_control(base, enable, 1);
+		break;
+	case ALCHEMY_USB_EHCI0:
+		__au1300_ehci_control(base, enable);
+		break;
+	case ALCHEMY_USB_UDC0:
+		__au1300_udc_control(base, enable);
+		break;
+	case ALCHEMY_USB_OTG0:
+		__au1300_otg_control(base, enable);
+		break;
+	default:
+		ret = -ENODEV;
+	}
+	return ret;
+}
+
+static inline void au1300_usb_init(void)
+{
+	void __iomem *base =
+		(void __iomem *)KSEG1ADDR(AU1300_USB_CTL_PHYS_ADDR);
+
+	/* set some sane defaults.  Note: we don't fiddle with DWC_CTRL4
+	 * here at all: Port 2 routing (EHCI or UDC) must be set either
+	 * by boot firmware or platform init code; I can't autodetect
+	 * a sane setting.
+	 */
+	__raw_writel(0, base + USB_INT_ENABLE); /* disable all USB irqs */
+	wmb();
+	__raw_writel(0, base + USB_DWC_CTRL3); /* disable all clocks */
+	wmb();
+	__raw_writel(~0, base + USB_MSR_ERR); /* clear all errors */
+	wmb();
+	__raw_writel(~0, base + USB_INT_STATUS); /* clear int status */
+	wmb();
+	/* set coherent access bit */
+	__raw_writel(USB_SBUS_CTRL_SBCA, base + USB_SBUS_CTRL);
+	wmb();
+}
+
+static inline void __au1200_ohci_control(void __iomem *base, int enable)
+{
+	unsigned long r = __raw_readl(base + AU1200_USBCFG);
+	if (enable) {
+		__raw_writel(r | USBCFG_OCE, base + AU1200_USBCFG);
+		wmb();
+		udelay(2000);
+	} else {
+		__raw_writel(r & ~USBCFG_OCE, base + AU1200_USBCFG);
+		wmb();
+		udelay(1000);
+	}
+}
+
+static inline void __au1200_ehci_control(void __iomem *base, int enable)
+{
+	unsigned long r = __raw_readl(base + AU1200_USBCFG);
+	if (enable) {
+		__raw_writel(r | USBCFG_ECE | USBCFG_PPE, base + AU1200_USBCFG);
+		wmb();
+		udelay(1000);
+	} else {
+		if (!(r & USBCFG_UCE))		/* UDC also off? */
+			r &= ~USBCFG_PPE;	/* yes: disable HS PHY PLL */
+		__raw_writel(r & ~USBCFG_ECE, base + AU1200_USBCFG);
+		wmb();
+		udelay(1000);
+	}
+}
+
+static inline void __au1200_udc_control(void __iomem *base, int enable)
+{
+	unsigned long r = __raw_readl(base + AU1200_USBCFG);
+	if (enable) {
+		__raw_writel(r | USBCFG_UCE | USBCFG_PPE, base + AU1200_USBCFG);
+		wmb();
+	} else {
+		if (!(r & USBCFG_ECE))		/* EHCI also off? */
+			r &= ~USBCFG_PPE;	/* yes: disable HS PHY PLL */
+		__raw_writel(r & ~USBCFG_UCE, base + AU1200_USBCFG);
+		wmb();
+	}
+}
+
+static inline int au1200_usb_control(int block, int enable)
+{
+	void __iomem *base =
+			(void __iomem *)KSEG1ADDR(AU1200_USB_CTL_PHYS_ADDR);
+
+	switch (block) {
+	case ALCHEMY_USB_OHCI0:
+		__au1200_ohci_control(base, enable);
+		break;
+	case ALCHEMY_USB_UDC0:
+		__au1200_udc_control(base, enable);
+		break;
+	case ALCHEMY_USB_EHCI0:
+		__au1200_ehci_control(base, enable);
+		break;
+	default:
+		return -ENODEV;
+	}
+	return 0;
+}
+
+
+/* initialize USB block(s) to a known working state */
+static inline void au1200_usb_init(void)
+{
+	void __iomem *base =
+			(void __iomem *)KSEG1ADDR(AU1200_USB_CTL_PHYS_ADDR);
+	__raw_writel(USBCFG_INIT_AU1200, base + AU1200_USBCFG);
+	wmb();
+	udelay(1000);
+}
+
+static inline int au1000_usb_init(unsigned long rb, int reg)
+{
+	void __iomem *base = (void __iomem *)KSEG1ADDR(rb + reg);
+	unsigned long r = __raw_readl(base);
+	struct clk *c;
+
+	/* 48MHz check. Don't init if no one can provide it */
+	c = clk_get(NULL, "usbh_clk");
+	if (IS_ERR(c))
+		return -ENODEV;
+	if (clk_round_rate(c, 48000000) != 48000000) {
+		clk_put(c);
+		return -ENODEV;
+	}
+	if (clk_set_rate(c, 48000000)) {
+		clk_put(c);
+		return -ENODEV;
+	}
+	clk_put(c);
+
+#if defined(__BIG_ENDIAN)
+	r |= USBHEN_BE;
+#endif
+	r |= USBHEN_C;
+
+	__raw_writel(r, base);
+	wmb();
+	udelay(1000);
+
+	return 0;
+}
+
+
+static inline void __au1xx0_ohci_control(int enable, unsigned long rb, int creg)
+{
+	void __iomem *base = (void __iomem *)KSEG1ADDR(rb);
+	unsigned long r = __raw_readl(base + creg);
+	struct clk *c = clk_get(NULL, "usbh_clk");
+
+	if (IS_ERR(c))
+		return;
+
+	if (enable) {
+		if (clk_prepare_enable(c))
+			goto out;
+
+		__raw_writel(r | USBHEN_CE, base + creg);
+		wmb();
+		udelay(1000);
+		__raw_writel(r | USBHEN_CE | USBHEN_E, base + creg);
+		wmb();
+		udelay(1000);
+
+		/* wait for reset complete (read reg twice: au1500 erratum) */
+		while (__raw_readl(base + creg),
+			!(__raw_readl(base + creg) & USBHEN_RD))
+			udelay(1000);
+	} else {
+		__raw_writel(r & ~(USBHEN_CE | USBHEN_E), base + creg);
+		wmb();
+		clk_disable_unprepare(c);
+	}
+out:
+	clk_put(c);
+}
+
+static inline int au1000_usb_control(int block, int enable, unsigned long rb,
+				     int creg)
+{
+	int ret = 0;
+
+	switch (block) {
+	case ALCHEMY_USB_OHCI0:
+		__au1xx0_ohci_control(enable, rb, creg);
+		break;
+	default:
+		ret = -ENODEV;
+	}
+	return ret;
+}
+
+/*
+ * alchemy_usb_control - control Alchemy on-chip USB blocks
+ * @block:	USB block to target
+ * @enable:	set 1 to enable a block, 0 to disable
+ */
+int alchemy_usb_control(int block, int enable)
+{
+	unsigned long flags;
+	int ret;
+
+	spin_lock_irqsave(&alchemy_usb_lock, flags);
+	switch (alchemy_get_cputype()) {
+	case ALCHEMY_CPU_AU1000:
+	case ALCHEMY_CPU_AU1500:
+	case ALCHEMY_CPU_AU1100:
+		ret = au1000_usb_control(block, enable,
+			AU1000_USB_OHCI_PHYS_ADDR, AU1000_OHCICFG);
+		break;
+	case ALCHEMY_CPU_AU1550:
+		ret = au1000_usb_control(block, enable,
+			AU1550_USB_OHCI_PHYS_ADDR, AU1550_OHCICFG);
+		break;
+	case ALCHEMY_CPU_AU1200:
+		ret = au1200_usb_control(block, enable);
+		break;
+	case ALCHEMY_CPU_AU1300:
+		ret = au1300_usb_control(block, enable);
+		break;
+	default:
+		ret = -ENODEV;
+	}
+	spin_unlock_irqrestore(&alchemy_usb_lock, flags);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(alchemy_usb_control);
+
+
+static unsigned long alchemy_usb_pmdata[2];
+
+static void au1000_usb_pm(unsigned long br, int creg, int susp)
+{
+	void __iomem *base = (void __iomem *)KSEG1ADDR(br);
+
+	if (susp) {
+		alchemy_usb_pmdata[0] = __raw_readl(base + creg);
+		/* There appears to be some undocumented reset register.... */
+		__raw_writel(0, base + 0x04);
+		wmb();
+		__raw_writel(0, base + creg);
+		wmb();
+	} else {
+		__raw_writel(alchemy_usb_pmdata[0], base + creg);
+		wmb();
+	}
+}
+
+static void au1200_usb_pm(int susp)
+{
+	void __iomem *base =
+			(void __iomem *)KSEG1ADDR(AU1200_USB_OTG_PHYS_ADDR);
+	if (susp) {
+		/* save OTG_CAP/MUX registers which indicate port routing */
+		/* FIXME: write an OTG driver to do that */
+		alchemy_usb_pmdata[0] = __raw_readl(base + 0x00);
+		alchemy_usb_pmdata[1] = __raw_readl(base + 0x04);
+	} else {
+		/* restore access to all MMIO areas */
+		au1200_usb_init();
+
+		/* restore OTG_CAP/MUX registers */
+		__raw_writel(alchemy_usb_pmdata[0], base + 0x00);
+		__raw_writel(alchemy_usb_pmdata[1], base + 0x04);
+		wmb();
+	}
+}
+
+static void au1300_usb_pm(int susp)
+{
+	void __iomem *base =
+			(void __iomem *)KSEG1ADDR(AU1300_USB_CTL_PHYS_ADDR);
+	/* remember Port2 routing */
+	if (susp) {
+		alchemy_usb_pmdata[0] = __raw_readl(base + USB_DWC_CTRL4);
+	} else {
+		au1300_usb_init();
+		__raw_writel(alchemy_usb_pmdata[0], base + USB_DWC_CTRL4);
+		wmb();
+	}
+}
+
+static void alchemy_usb_pm(int susp)
+{
+	switch (alchemy_get_cputype()) {
+	case ALCHEMY_CPU_AU1000:
+	case ALCHEMY_CPU_AU1500:
+	case ALCHEMY_CPU_AU1100:
+		au1000_usb_pm(AU1000_USB_OHCI_PHYS_ADDR, AU1000_OHCICFG, susp);
+		break;
+	case ALCHEMY_CPU_AU1550:
+		au1000_usb_pm(AU1550_USB_OHCI_PHYS_ADDR, AU1550_OHCICFG, susp);
+		break;
+	case ALCHEMY_CPU_AU1200:
+		au1200_usb_pm(susp);
+		break;
+	case ALCHEMY_CPU_AU1300:
+		au1300_usb_pm(susp);
+		break;
+	}
+}
+
+static int alchemy_usb_suspend(void)
+{
+	alchemy_usb_pm(1);
+	return 0;
+}
+
+static void alchemy_usb_resume(void)
+{
+	alchemy_usb_pm(0);
+}
+
+static struct syscore_ops alchemy_usb_pm_ops = {
+	.suspend	= alchemy_usb_suspend,
+	.resume		= alchemy_usb_resume,
+};
+
+static int __init alchemy_usb_init(void)
+{
+	int ret = 0;
+
+	switch (alchemy_get_cputype()) {
+	case ALCHEMY_CPU_AU1000:
+	case ALCHEMY_CPU_AU1500:
+	case ALCHEMY_CPU_AU1100:
+		ret = au1000_usb_init(AU1000_USB_OHCI_PHYS_ADDR,
+				      AU1000_OHCICFG);
+		break;
+	case ALCHEMY_CPU_AU1550:
+		ret = au1000_usb_init(AU1550_USB_OHCI_PHYS_ADDR,
+				      AU1550_OHCICFG);
+		break;
+	case ALCHEMY_CPU_AU1200:
+		au1200_usb_init();
+		break;
+	case ALCHEMY_CPU_AU1300:
+		au1300_usb_init();
+		break;
+	}
+
+	if (!ret)
+		register_syscore_ops(&alchemy_usb_pm_ops);
+
+	return ret;
+}
+arch_initcall(alchemy_usb_init);
diff --git a/arch/mips/alchemy/common/vss.c b/arch/mips/alchemy/common/vss.c
new file mode 100644
index 000000000..3d0d468d9
--- /dev/null
+++ b/arch/mips/alchemy/common/vss.c
@@ -0,0 +1,85 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Au1300 media block power gating (VSS)
+ *
+ * This is a stop-gap solution until I have the clock framework integration
+ * ready. This stuff here really must be handled transparently when clocks
+ * for various media blocks are enabled/disabled.
+ */
+
+#include <linux/export.h>
+#include <linux/spinlock.h>
+#include <asm/mach-au1x00/au1000.h>
+
+#define VSS_GATE	0x00	/* gate wait timers */
+#define VSS_CLKRST	0x04	/* clock/block control */
+#define VSS_FTR		0x08	/* footers */
+
+#define VSS_ADDR(blk)	(KSEG1ADDR(AU1300_VSS_PHYS_ADDR) + (blk * 0x0c))
+
+static DEFINE_SPINLOCK(au1300_vss_lock);
+
+/* enable a block as outlined in the databook */
+static inline void __enable_block(int block)
+{
+	void __iomem *base = (void __iomem *)VSS_ADDR(block);
+
+	__raw_writel(3, base + VSS_CLKRST);	/* enable clock, assert reset */
+	wmb();
+
+	__raw_writel(0x01fffffe, base + VSS_GATE); /* maximum setup time */
+	wmb();
+
+	/* enable footers in sequence */
+	__raw_writel(0x01, base + VSS_FTR);
+	wmb();
+	__raw_writel(0x03, base + VSS_FTR);
+	wmb();
+	__raw_writel(0x07, base + VSS_FTR);
+	wmb();
+	__raw_writel(0x0f, base + VSS_FTR);
+	wmb();
+
+	__raw_writel(0x01ffffff, base + VSS_GATE); /* start FSM too */
+	wmb();
+
+	__raw_writel(2, base + VSS_CLKRST);	/* deassert reset */
+	wmb();
+
+	__raw_writel(0x1f, base + VSS_FTR);	/* enable isolation cells */
+	wmb();
+}
+
+/* disable a block as outlined in the databook */
+static inline void __disable_block(int block)
+{
+	void __iomem *base = (void __iomem *)VSS_ADDR(block);
+
+	__raw_writel(0x0f, base + VSS_FTR);	/* disable isolation cells */
+	wmb();
+	__raw_writel(0, base + VSS_GATE);	/* disable FSM */
+	wmb();
+	__raw_writel(3, base + VSS_CLKRST);	/* assert reset */
+	wmb();
+	__raw_writel(1, base + VSS_CLKRST);	/* disable clock */
+	wmb();
+	__raw_writel(0, base + VSS_FTR);	/* disable all footers */
+	wmb();
+}
+
+void au1300_vss_block_control(int block, int enable)
+{
+	unsigned long flags;
+
+	if (alchemy_get_cputype() != ALCHEMY_CPU_AU1300)
+		return;
+
+	/* only one block at a time */
+	spin_lock_irqsave(&au1300_vss_lock, flags);
+	if (enable)
+		__enable_block(block);
+	else
+		__disable_block(block);
+	spin_unlock_irqrestore(&au1300_vss_lock, flags);
+}
+EXPORT_SYMBOL_GPL(au1300_vss_block_control);
diff --git a/arch/mips/alchemy/devboards/Makefile b/arch/mips/alchemy/devboards/Makefile
new file mode 100644
index 000000000..10a52283f
--- /dev/null
+++ b/arch/mips/alchemy/devboards/Makefile
@@ -0,0 +1,7 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Alchemy Develboards
+#
+
+obj-y += bcsr.o platform.o db1000.o db1200.o db1300.o db1550.o db1xxx.o
+obj-$(CONFIG_PM)		+= pm.o
diff --git a/arch/mips/alchemy/devboards/bcsr.c b/arch/mips/alchemy/devboards/bcsr.c
new file mode 100644
index 000000000..8df0ccdc9
--- /dev/null
+++ b/arch/mips/alchemy/devboards/bcsr.c
@@ -0,0 +1,147 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * bcsr.h -- Db1xxx/Pb1xxx Devboard CPLD registers ("BCSR") abstraction.
+ *
+ * All Alchemy development boards (except, of course, the weird PB1000)
+ * have a few registers in a CPLD with standardised layout; they mostly
+ * only differ in base address.
+ * All registers are 16bits wide with 32bit spacing.
+ */
+
+#include <linux/interrupt.h>
+#include <linux/irqchip/chained_irq.h>
+#include <linux/init.h>
+#include <linux/export.h>
+#include <linux/spinlock.h>
+#include <linux/irq.h>
+#include <asm/addrspace.h>
+#include <asm/io.h>
+#include <asm/mach-db1x00/bcsr.h>
+
+static struct bcsr_reg {
+	void __iomem *raddr;
+	spinlock_t lock;
+} bcsr_regs[BCSR_CNT];
+
+static void __iomem *bcsr_virt; /* KSEG1 addr of BCSR base */
+static int bcsr_csc_base;	/* linux-irq of first cascaded irq */
+
+void __init bcsr_init(unsigned long bcsr1_phys, unsigned long bcsr2_phys)
+{
+	int i;
+
+	bcsr1_phys = KSEG1ADDR(CPHYSADDR(bcsr1_phys));
+	bcsr2_phys = KSEG1ADDR(CPHYSADDR(bcsr2_phys));
+
+	bcsr_virt = (void __iomem *)bcsr1_phys;
+
+	for (i = 0; i < BCSR_CNT; i++) {
+		if (i >= BCSR_HEXLEDS)
+			bcsr_regs[i].raddr = (void __iomem *)bcsr2_phys +
+					(0x04 * (i - BCSR_HEXLEDS));
+		else
+			bcsr_regs[i].raddr = (void __iomem *)bcsr1_phys +
+					(0x04 * i);
+
+		spin_lock_init(&bcsr_regs[i].lock);
+	}
+}
+
+unsigned short bcsr_read(enum bcsr_id reg)
+{
+	unsigned short r;
+	unsigned long flags;
+
+	spin_lock_irqsave(&bcsr_regs[reg].lock, flags);
+	r = __raw_readw(bcsr_regs[reg].raddr);
+	spin_unlock_irqrestore(&bcsr_regs[reg].lock, flags);
+	return r;
+}
+EXPORT_SYMBOL_GPL(bcsr_read);
+
+void bcsr_write(enum bcsr_id reg, unsigned short val)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&bcsr_regs[reg].lock, flags);
+	__raw_writew(val, bcsr_regs[reg].raddr);
+	wmb();
+	spin_unlock_irqrestore(&bcsr_regs[reg].lock, flags);
+}
+EXPORT_SYMBOL_GPL(bcsr_write);
+
+void bcsr_mod(enum bcsr_id reg, unsigned short clr, unsigned short set)
+{
+	unsigned short r;
+	unsigned long flags;
+
+	spin_lock_irqsave(&bcsr_regs[reg].lock, flags);
+	r = __raw_readw(bcsr_regs[reg].raddr);
+	r &= ~clr;
+	r |= set;
+	__raw_writew(r, bcsr_regs[reg].raddr);
+	wmb();
+	spin_unlock_irqrestore(&bcsr_regs[reg].lock, flags);
+}
+EXPORT_SYMBOL_GPL(bcsr_mod);
+
+/*
+ * DB1200/PB1200 CPLD IRQ muxer
+ */
+static void bcsr_csc_handler(struct irq_desc *d)
+{
+	unsigned short bisr = __raw_readw(bcsr_virt + BCSR_REG_INTSTAT);
+	struct irq_chip *chip = irq_desc_get_chip(d);
+
+	chained_irq_enter(chip, d);
+	generic_handle_irq(bcsr_csc_base + __ffs(bisr));
+	chained_irq_exit(chip, d);
+}
+
+static void bcsr_irq_mask(struct irq_data *d)
+{
+	unsigned short v = 1 << (d->irq - bcsr_csc_base);
+	__raw_writew(v, bcsr_virt + BCSR_REG_MASKCLR);
+	wmb();
+}
+
+static void bcsr_irq_maskack(struct irq_data *d)
+{
+	unsigned short v = 1 << (d->irq - bcsr_csc_base);
+	__raw_writew(v, bcsr_virt + BCSR_REG_MASKCLR);
+	__raw_writew(v, bcsr_virt + BCSR_REG_INTSTAT);	/* ack */
+	wmb();
+}
+
+static void bcsr_irq_unmask(struct irq_data *d)
+{
+	unsigned short v = 1 << (d->irq - bcsr_csc_base);
+	__raw_writew(v, bcsr_virt + BCSR_REG_MASKSET);
+	wmb();
+}
+
+static struct irq_chip bcsr_irq_type = {
+	.name		= "CPLD",
+	.irq_mask	= bcsr_irq_mask,
+	.irq_mask_ack	= bcsr_irq_maskack,
+	.irq_unmask	= bcsr_irq_unmask,
+};
+
+void __init bcsr_init_irq(int csc_start, int csc_end, int hook_irq)
+{
+	unsigned int irq;
+
+	/* mask & enable & ack all */
+	__raw_writew(0xffff, bcsr_virt + BCSR_REG_MASKCLR);
+	__raw_writew(0xffff, bcsr_virt + BCSR_REG_INTSET);
+	__raw_writew(0xffff, bcsr_virt + BCSR_REG_INTSTAT);
+	wmb();
+
+	bcsr_csc_base = csc_start;
+
+	for (irq = csc_start; irq <= csc_end; irq++)
+		irq_set_chip_and_handler_name(irq, &bcsr_irq_type,
+					      handle_level_irq, "level");
+
+	irq_set_chained_handler(hook_irq, bcsr_csc_handler);
+}
diff --git a/arch/mips/alchemy/devboards/db1000.c b/arch/mips/alchemy/devboards/db1000.c
new file mode 100644
index 000000000..3183df60a
--- /dev/null
+++ b/arch/mips/alchemy/devboards/db1000.c
@@ -0,0 +1,562 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * DBAu1000/1500/1100 PBAu1100/1500 board support
+ *
+ * Copyright 2000, 2008 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc. <source@mvista.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/leds.h>
+#include <linux/mmc/host.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/spi_gpio.h>
+#include <linux/spi/ads7846.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/gpio-au1000.h>
+#include <asm/mach-au1x00/au1000_dma.h>
+#include <asm/mach-au1x00/au1100_mmc.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <asm/reboot.h>
+#include <prom.h>
+#include "platform.h"
+
+#define F_SWAPPED (bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT)
+
+const char *get_system_type(void);
+
+int __init db1000_board_setup(void)
+{
+	/* initialize board register space */
+	bcsr_init(DB1000_BCSR_PHYS_ADDR,
+		  DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS);
+
+	switch (BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI))) {
+	case BCSR_WHOAMI_DB1000:
+	case BCSR_WHOAMI_DB1500:
+	case BCSR_WHOAMI_DB1100:
+	case BCSR_WHOAMI_PB1500:
+	case BCSR_WHOAMI_PB1500R2:
+	case BCSR_WHOAMI_PB1100:
+		pr_info("AMD Alchemy %s Board\n", get_system_type());
+		return 0;
+	}
+	return -ENODEV;
+}
+
+static int db1500_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
+{
+	if ((slot < 12) || (slot > 13) || pin == 0)
+		return -1;
+	if (slot == 12)
+		return (pin == 1) ? AU1500_PCI_INTA : 0xff;
+	if (slot == 13) {
+		switch (pin) {
+		case 1: return AU1500_PCI_INTA;
+		case 2: return AU1500_PCI_INTB;
+		case 3: return AU1500_PCI_INTC;
+		case 4: return AU1500_PCI_INTD;
+		}
+	}
+	return -1;
+}
+
+static u64 au1xxx_all_dmamask = DMA_BIT_MASK(32);
+
+static struct resource alchemy_pci_host_res[] = {
+	[0] = {
+		.start	= AU1500_PCI_PHYS_ADDR,
+		.end	= AU1500_PCI_PHYS_ADDR + 0xfff,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+static struct alchemy_pci_platdata db1500_pci_pd = {
+	.board_map_irq	= db1500_map_pci_irq,
+};
+
+static struct platform_device db1500_pci_host_dev = {
+	.dev.platform_data = &db1500_pci_pd,
+	.name		= "alchemy-pci",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(alchemy_pci_host_res),
+	.resource	= alchemy_pci_host_res,
+};
+
+int __init db1500_pci_setup(void)
+{
+	return platform_device_register(&db1500_pci_host_dev);
+}
+
+static struct resource au1100_lcd_resources[] = {
+	[0] = {
+		.start	= AU1100_LCD_PHYS_ADDR,
+		.end	= AU1100_LCD_PHYS_ADDR + 0x800 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AU1100_LCD_INT,
+		.end	= AU1100_LCD_INT,
+		.flags	= IORESOURCE_IRQ,
+	}
+};
+
+static struct platform_device au1100_lcd_device = {
+	.name		= "au1100-lcd",
+	.id		= 0,
+	.dev = {
+		.dma_mask		= &au1xxx_all_dmamask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+	.num_resources	= ARRAY_SIZE(au1100_lcd_resources),
+	.resource	= au1100_lcd_resources,
+};
+
+static struct resource alchemy_ac97c_res[] = {
+	[0] = {
+		.start	= AU1000_AC97_PHYS_ADDR,
+		.end	= AU1000_AC97_PHYS_ADDR + 0xfff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= DMA_ID_AC97C_TX,
+		.end	= DMA_ID_AC97C_TX,
+		.flags	= IORESOURCE_DMA,
+	},
+	[2] = {
+		.start	= DMA_ID_AC97C_RX,
+		.end	= DMA_ID_AC97C_RX,
+		.flags	= IORESOURCE_DMA,
+	},
+};
+
+static struct platform_device alchemy_ac97c_dev = {
+	.name		= "alchemy-ac97c",
+	.id		= -1,
+	.resource	= alchemy_ac97c_res,
+	.num_resources	= ARRAY_SIZE(alchemy_ac97c_res),
+};
+
+static struct platform_device alchemy_ac97c_dma_dev = {
+	.name		= "alchemy-pcm-dma",
+	.id		= 0,
+};
+
+static struct platform_device db1x00_codec_dev = {
+	.name		= "ac97-codec",
+	.id		= -1,
+};
+
+static struct platform_device db1x00_audio_dev = {
+	.name		= "db1000-audio",
+	.dev = {
+		.dma_mask		= &au1xxx_all_dmamask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+};
+
+/******************************************************************************/
+
+#ifdef CONFIG_MMC_AU1X
+static irqreturn_t db1100_mmc_cd(int irq, void *ptr)
+{
+	mmc_detect_change(ptr, msecs_to_jiffies(500));
+	return IRQ_HANDLED;
+}
+
+static int db1100_mmc_cd_setup(void *mmc_host, int en)
+{
+	int ret = 0, irq;
+
+	if (BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI)) == BCSR_WHOAMI_DB1100)
+		irq = AU1100_GPIO19_INT;
+	else
+		irq = AU1100_GPIO14_INT;	/* PB1100 SD0 CD# */
+
+	if (en) {
+		irq_set_irq_type(irq, IRQ_TYPE_EDGE_BOTH);
+		ret = request_irq(irq, db1100_mmc_cd, 0,
+				  "sd0_cd", mmc_host);
+	} else
+		free_irq(irq, mmc_host);
+	return ret;
+}
+
+static int db1100_mmc1_cd_setup(void *mmc_host, int en)
+{
+	int ret = 0, irq;
+
+	if (BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI)) == BCSR_WHOAMI_DB1100)
+		irq = AU1100_GPIO20_INT;
+	else
+		irq = AU1100_GPIO15_INT;	/* PB1100 SD1 CD# */
+
+	if (en) {
+		irq_set_irq_type(irq, IRQ_TYPE_EDGE_BOTH);
+		ret = request_irq(irq, db1100_mmc_cd, 0,
+				  "sd1_cd", mmc_host);
+	} else
+		free_irq(irq, mmc_host);
+	return ret;
+}
+
+static int db1100_mmc_card_readonly(void *mmc_host)
+{
+	/* testing suggests that this bit is inverted */
+	return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD0WP) ? 0 : 1;
+}
+
+static int db1100_mmc_card_inserted(void *mmc_host)
+{
+	return !alchemy_gpio_get_value(19);
+}
+
+static void db1100_mmc_set_power(void *mmc_host, int state)
+{
+	int bit;
+
+	if (BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI)) == BCSR_WHOAMI_DB1100)
+		bit = BCSR_BOARD_SD0PWR;
+	else
+		bit = BCSR_BOARD_PB1100_SD0PWR;
+
+	if (state) {
+		bcsr_mod(BCSR_BOARD, 0, bit);
+		msleep(400);	/* stabilization time */
+	} else
+		bcsr_mod(BCSR_BOARD, bit, 0);
+}
+
+static void db1100_mmcled_set(struct led_classdev *led, enum led_brightness b)
+{
+	if (b != LED_OFF)
+		bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED0, 0);
+	else
+		bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED0);
+}
+
+static struct led_classdev db1100_mmc_led = {
+	.brightness_set = db1100_mmcled_set,
+};
+
+static int db1100_mmc1_card_readonly(void *mmc_host)
+{
+	return (bcsr_read(BCSR_BOARD) & BCSR_BOARD_SD1WP) ? 1 : 0;
+}
+
+static int db1100_mmc1_card_inserted(void *mmc_host)
+{
+	return !alchemy_gpio_get_value(20);
+}
+
+static void db1100_mmc1_set_power(void *mmc_host, int state)
+{
+	int bit;
+
+	if (BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI)) == BCSR_WHOAMI_DB1100)
+		bit = BCSR_BOARD_SD1PWR;
+	else
+		bit = BCSR_BOARD_PB1100_SD1PWR;
+
+	if (state) {
+		bcsr_mod(BCSR_BOARD, 0, bit);
+		msleep(400);	/* stabilization time */
+	} else
+		bcsr_mod(BCSR_BOARD, bit, 0);
+}
+
+static void db1100_mmc1led_set(struct led_classdev *led, enum led_brightness b)
+{
+	if (b != LED_OFF)
+		bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED1, 0);
+	else
+		bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED1);
+}
+
+static struct led_classdev db1100_mmc1_led = {
+	.brightness_set = db1100_mmc1led_set,
+};
+
+static struct au1xmmc_platform_data db1100_mmc_platdata[2] = {
+	[0] = {
+		.cd_setup	= db1100_mmc_cd_setup,
+		.set_power	= db1100_mmc_set_power,
+		.card_inserted	= db1100_mmc_card_inserted,
+		.card_readonly	= db1100_mmc_card_readonly,
+		.led		= &db1100_mmc_led,
+	},
+	[1] = {
+		.cd_setup	= db1100_mmc1_cd_setup,
+		.set_power	= db1100_mmc1_set_power,
+		.card_inserted	= db1100_mmc1_card_inserted,
+		.card_readonly	= db1100_mmc1_card_readonly,
+		.led		= &db1100_mmc1_led,
+	},
+};
+
+static struct resource au1100_mmc0_resources[] = {
+	[0] = {
+		.start	= AU1100_SD0_PHYS_ADDR,
+		.end	= AU1100_SD0_PHYS_ADDR + 0xfff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AU1100_SD_INT,
+		.end	= AU1100_SD_INT,
+		.flags	= IORESOURCE_IRQ,
+	},
+	[2] = {
+		.start	= DMA_ID_SD0_TX,
+		.end	= DMA_ID_SD0_TX,
+		.flags	= IORESOURCE_DMA,
+	},
+	[3] = {
+		.start	= DMA_ID_SD0_RX,
+		.end	= DMA_ID_SD0_RX,
+		.flags	= IORESOURCE_DMA,
+	}
+};
+
+static struct platform_device db1100_mmc0_dev = {
+	.name		= "au1xxx-mmc",
+	.id		= 0,
+	.dev = {
+		.dma_mask		= &au1xxx_all_dmamask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+		.platform_data		= &db1100_mmc_platdata[0],
+	},
+	.num_resources	= ARRAY_SIZE(au1100_mmc0_resources),
+	.resource	= au1100_mmc0_resources,
+};
+
+static struct resource au1100_mmc1_res[] = {
+	[0] = {
+		.start	= AU1100_SD1_PHYS_ADDR,
+		.end	= AU1100_SD1_PHYS_ADDR + 0xfff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AU1100_SD_INT,
+		.end	= AU1100_SD_INT,
+		.flags	= IORESOURCE_IRQ,
+	},
+	[2] = {
+		.start	= DMA_ID_SD1_TX,
+		.end	= DMA_ID_SD1_TX,
+		.flags	= IORESOURCE_DMA,
+	},
+	[3] = {
+		.start	= DMA_ID_SD1_RX,
+		.end	= DMA_ID_SD1_RX,
+		.flags	= IORESOURCE_DMA,
+	}
+};
+
+static struct platform_device db1100_mmc1_dev = {
+	.name		= "au1xxx-mmc",
+	.id		= 1,
+	.dev = {
+		.dma_mask		= &au1xxx_all_dmamask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+		.platform_data		= &db1100_mmc_platdata[1],
+	},
+	.num_resources	= ARRAY_SIZE(au1100_mmc1_res),
+	.resource	= au1100_mmc1_res,
+};
+#endif /* CONFIG_MMC_AU1X */
+
+/******************************************************************************/
+
+static struct ads7846_platform_data db1100_touch_pd = {
+	.model		= 7846,
+	.vref_mv	= 3300,
+	.gpio_pendown	= 21,
+};
+
+static struct spi_gpio_platform_data db1100_spictl_pd = {
+	.num_chipselect = 1,
+};
+
+static struct spi_board_info db1100_spi_info[] __initdata = {
+	[0] = {
+		.modalias	 = "ads7846",
+		.max_speed_hz	 = 3250000,
+		.bus_num	 = 0,
+		.chip_select	 = 0,
+		.mode		 = 0,
+		.irq		 = AU1100_GPIO21_INT,
+		.platform_data	 = &db1100_touch_pd,
+	},
+};
+
+static struct platform_device db1100_spi_dev = {
+	.name		= "spi_gpio",
+	.id		= 0,
+	.dev		= {
+		.platform_data	= &db1100_spictl_pd,
+		.dma_mask		= &au1xxx_all_dmamask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+};
+
+/*
+ * Alchemy GPIO 2 has its base at 200 so the GPIO lines
+ * 207 thru 210 are GPIOs at offset 7 thru 10 at this chip.
+ */
+static struct gpiod_lookup_table db1100_spi_gpiod_table = {
+	.dev_id         = "spi_gpio",
+	.table          = {
+		GPIO_LOOKUP("alchemy-gpio2", 9,
+			    "sck", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("alchemy-gpio2", 8,
+			    "mosi", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("alchemy-gpio2", 7,
+			    "miso", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("alchemy-gpio2", 10,
+			    "cs", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
+static struct platform_device *db1x00_devs[] = {
+	&db1x00_codec_dev,
+	&alchemy_ac97c_dma_dev,
+	&alchemy_ac97c_dev,
+	&db1x00_audio_dev,
+};
+
+static struct platform_device *db1100_devs[] = {
+	&au1100_lcd_device,
+#ifdef CONFIG_MMC_AU1X
+	&db1100_mmc0_dev,
+	&db1100_mmc1_dev,
+#endif
+};
+
+int __init db1000_dev_setup(void)
+{
+	int board = BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI));
+	int c0, c1, d0, d1, s0, s1, flashsize = 32,  twosocks = 1;
+	unsigned long pfc;
+	struct clk *c, *p;
+
+	if (board == BCSR_WHOAMI_DB1500) {
+		c0 = AU1500_GPIO2_INT;
+		c1 = AU1500_GPIO5_INT;
+		d0 = 0;	/* GPIO number, NOT irq! */
+		d1 = 3; /* GPIO number, NOT irq! */
+		s0 = AU1500_GPIO1_INT;
+		s1 = AU1500_GPIO4_INT;
+	} else if (board == BCSR_WHOAMI_DB1100) {
+		c0 = AU1100_GPIO2_INT;
+		c1 = AU1100_GPIO5_INT;
+		d0 = 0; /* GPIO number, NOT irq! */
+		d1 = 3; /* GPIO number, NOT irq! */
+		s0 = AU1100_GPIO1_INT;
+		s1 = AU1100_GPIO4_INT;
+
+		gpio_request(19, "sd0_cd");
+		gpio_request(20, "sd1_cd");
+		gpio_direction_input(19);	/* sd0 cd# */
+		gpio_direction_input(20);	/* sd1 cd# */
+
+		/* spi_gpio on SSI0 pins */
+		pfc = alchemy_rdsys(AU1000_SYS_PINFUNC);
+		pfc |= (1 << 0);	/* SSI0 pins as GPIOs */
+		alchemy_wrsys(pfc, AU1000_SYS_PINFUNC);
+
+		spi_register_board_info(db1100_spi_info,
+					ARRAY_SIZE(db1100_spi_info));
+
+		/* link LCD clock to AUXPLL */
+		p = clk_get(NULL, "auxpll_clk");
+		c = clk_get(NULL, "lcd_intclk");
+		if (!IS_ERR(c) && !IS_ERR(p)) {
+			clk_set_parent(c, p);
+			clk_set_rate(c, clk_get_rate(p));
+		}
+		if (!IS_ERR(c))
+			clk_put(c);
+		if (!IS_ERR(p))
+			clk_put(p);
+
+		platform_add_devices(db1100_devs, ARRAY_SIZE(db1100_devs));
+		gpiod_add_lookup_table(&db1100_spi_gpiod_table);
+		platform_device_register(&db1100_spi_dev);
+	} else if (board == BCSR_WHOAMI_DB1000) {
+		c0 = AU1000_GPIO2_INT;
+		c1 = AU1000_GPIO5_INT;
+		d0 = 0; /* GPIO number, NOT irq! */
+		d1 = 3; /* GPIO number, NOT irq! */
+		s0 = AU1000_GPIO1_INT;
+		s1 = AU1000_GPIO4_INT;
+	} else if ((board == BCSR_WHOAMI_PB1500) ||
+		   (board == BCSR_WHOAMI_PB1500R2)) {
+		c0 = AU1500_GPIO203_INT;
+		d0 = 1; /* GPIO number, NOT irq! */
+		s0 = AU1500_GPIO202_INT;
+		twosocks = 0;
+		flashsize = 64;
+		/* RTC and daughtercard irqs */
+		irq_set_irq_type(AU1500_GPIO204_INT, IRQ_TYPE_LEVEL_LOW);
+		irq_set_irq_type(AU1500_GPIO205_INT, IRQ_TYPE_LEVEL_LOW);
+		/* EPSON S1D13806 0x1b000000
+		 * SRAM 1MB/2MB	  0x1a000000
+		 * DS1693 RTC	  0x0c000000
+		 */
+	} else if (board == BCSR_WHOAMI_PB1100) {
+		c0 = AU1100_GPIO11_INT;
+		d0 = 9; /* GPIO number, NOT irq! */
+		s0 = AU1100_GPIO10_INT;
+		twosocks = 0;
+		flashsize = 64;
+		/* pendown, rtc, daughtercard irqs */
+		irq_set_irq_type(AU1100_GPIO8_INT, IRQ_TYPE_LEVEL_LOW);
+		irq_set_irq_type(AU1100_GPIO12_INT, IRQ_TYPE_LEVEL_LOW);
+		irq_set_irq_type(AU1100_GPIO13_INT, IRQ_TYPE_LEVEL_LOW);
+		/* EPSON S1D13806 0x1b000000
+		 * SRAM 1MB/2MB	  0x1a000000
+		 * DiskOnChip	  0x0d000000
+		 * DS1693 RTC	  0x0c000000
+		 */
+		platform_add_devices(db1100_devs, ARRAY_SIZE(db1100_devs));
+	} else
+		return 0; /* unknown board, no further dev setup to do */
+
+	irq_set_irq_type(c0, IRQ_TYPE_LEVEL_LOW);
+	irq_set_irq_type(s0, IRQ_TYPE_LEVEL_LOW);
+
+	db1x_register_pcmcia_socket(
+		AU1000_PCMCIA_ATTR_PHYS_ADDR,
+		AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+		AU1000_PCMCIA_MEM_PHYS_ADDR,
+		AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x000400000 - 1,
+		AU1000_PCMCIA_IO_PHYS_ADDR,
+		AU1000_PCMCIA_IO_PHYS_ADDR   + 0x000010000 - 1,
+		c0, d0, /*s0*/0, 0, 0);
+
+	if (twosocks) {
+		irq_set_irq_type(c1, IRQ_TYPE_LEVEL_LOW);
+		irq_set_irq_type(s1, IRQ_TYPE_LEVEL_LOW);
+
+		db1x_register_pcmcia_socket(
+			AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
+			AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
+			AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x004000000,
+			AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x004400000 - 1,
+			AU1000_PCMCIA_IO_PHYS_ADDR   + 0x004000000,
+			AU1000_PCMCIA_IO_PHYS_ADDR   + 0x004010000 - 1,
+			c1, d1, /*s1*/0, 0, 1);
+	}
+
+	platform_add_devices(db1x00_devs, ARRAY_SIZE(db1x00_devs));
+	db1x_register_norflash(flashsize << 20, 4 /* 32bit */, F_SWAPPED);
+	return 0;
+}
diff --git a/arch/mips/alchemy/devboards/db1200.c b/arch/mips/alchemy/devboards/db1200.c
new file mode 100644
index 000000000..67f067706
--- /dev/null
+++ b/arch/mips/alchemy/devboards/db1200.c
@@ -0,0 +1,943 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * DBAu1200/PBAu1200 board platform device registration
+ *
+ * Copyright (C) 2008-2011 Manuel Lauss
+ */
+
+#include <linux/clk.h>
+#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/leds.h>
+#include <linux/mmc/host.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/platnand.h>
+#include <linux/platform_device.h>
+#include <linux/serial_8250.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#include <linux/smc91x.h>
+#include <linux/ata_platform.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1100_mmc.h>
+#include <asm/mach-au1x00/au1xxx_dbdma.h>
+#include <asm/mach-au1x00/au1xxx_psc.h>
+#include <asm/mach-au1x00/au1200fb.h>
+#include <asm/mach-au1x00/au1550_spi.h>
+#include <asm/mach-db1x00/bcsr.h>
+
+#include "platform.h"
+
+#define BCSR_INT_IDE		0x0001
+#define BCSR_INT_ETH		0x0002
+#define BCSR_INT_PC0		0x0004
+#define BCSR_INT_PC0STSCHG	0x0008
+#define BCSR_INT_PC1		0x0010
+#define BCSR_INT_PC1STSCHG	0x0020
+#define BCSR_INT_DC		0x0040
+#define BCSR_INT_FLASHBUSY	0x0080
+#define BCSR_INT_PC0INSERT	0x0100
+#define BCSR_INT_PC0EJECT	0x0200
+#define BCSR_INT_PC1INSERT	0x0400
+#define BCSR_INT_PC1EJECT	0x0800
+#define BCSR_INT_SD0INSERT	0x1000
+#define BCSR_INT_SD0EJECT	0x2000
+#define BCSR_INT_SD1INSERT	0x4000
+#define BCSR_INT_SD1EJECT	0x8000
+
+#define DB1200_IDE_PHYS_ADDR	0x18800000
+#define DB1200_IDE_REG_SHIFT	5
+#define DB1200_IDE_PHYS_LEN	(16 << DB1200_IDE_REG_SHIFT)
+#define DB1200_ETH_PHYS_ADDR	0x19000300
+#define DB1200_NAND_PHYS_ADDR	0x20000000
+
+#define PB1200_IDE_PHYS_ADDR	0x0C800000
+#define PB1200_ETH_PHYS_ADDR	0x0D000300
+#define PB1200_NAND_PHYS_ADDR	0x1C000000
+
+#define DB1200_INT_BEGIN	(AU1000_MAX_INTR + 1)
+#define DB1200_IDE_INT		(DB1200_INT_BEGIN + 0)
+#define DB1200_ETH_INT		(DB1200_INT_BEGIN + 1)
+#define DB1200_PC0_INT		(DB1200_INT_BEGIN + 2)
+#define DB1200_PC0_STSCHG_INT	(DB1200_INT_BEGIN + 3)
+#define DB1200_PC1_INT		(DB1200_INT_BEGIN + 4)
+#define DB1200_PC1_STSCHG_INT	(DB1200_INT_BEGIN + 5)
+#define DB1200_DC_INT		(DB1200_INT_BEGIN + 6)
+#define DB1200_FLASHBUSY_INT	(DB1200_INT_BEGIN + 7)
+#define DB1200_PC0_INSERT_INT	(DB1200_INT_BEGIN + 8)
+#define DB1200_PC0_EJECT_INT	(DB1200_INT_BEGIN + 9)
+#define DB1200_PC1_INSERT_INT	(DB1200_INT_BEGIN + 10)
+#define DB1200_PC1_EJECT_INT	(DB1200_INT_BEGIN + 11)
+#define DB1200_SD0_INSERT_INT	(DB1200_INT_BEGIN + 12)
+#define DB1200_SD0_EJECT_INT	(DB1200_INT_BEGIN + 13)
+#define PB1200_SD1_INSERT_INT	(DB1200_INT_BEGIN + 14)
+#define PB1200_SD1_EJECT_INT	(DB1200_INT_BEGIN + 15)
+#define DB1200_INT_END		(DB1200_INT_BEGIN + 15)
+
+const char *get_system_type(void);
+
+static int __init db1200_detect_board(void)
+{
+	int bid;
+
+	/* try the DB1200 first */
+	bcsr_init(DB1200_BCSR_PHYS_ADDR,
+		  DB1200_BCSR_PHYS_ADDR + DB1200_BCSR_HEXLED_OFS);
+	if (BCSR_WHOAMI_DB1200 == BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI))) {
+		unsigned short t = bcsr_read(BCSR_HEXLEDS);
+		bcsr_write(BCSR_HEXLEDS, ~t);
+		if (bcsr_read(BCSR_HEXLEDS) != t) {
+			bcsr_write(BCSR_HEXLEDS, t);
+			return 0;
+		}
+	}
+
+	/* okay, try the PB1200 then */
+	bcsr_init(PB1200_BCSR_PHYS_ADDR,
+		  PB1200_BCSR_PHYS_ADDR + PB1200_BCSR_HEXLED_OFS);
+	bid = BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI));
+	if ((bid == BCSR_WHOAMI_PB1200_DDR1) ||
+	    (bid == BCSR_WHOAMI_PB1200_DDR2)) {
+		unsigned short t = bcsr_read(BCSR_HEXLEDS);
+		bcsr_write(BCSR_HEXLEDS, ~t);
+		if (bcsr_read(BCSR_HEXLEDS) != t) {
+			bcsr_write(BCSR_HEXLEDS, t);
+			return 0;
+		}
+	}
+
+	return 1;	/* it's neither */
+}
+
+int __init db1200_board_setup(void)
+{
+	unsigned short whoami;
+
+	if (db1200_detect_board())
+		return -ENODEV;
+
+	whoami = bcsr_read(BCSR_WHOAMI);
+	switch (BCSR_WHOAMI_BOARD(whoami)) {
+	case BCSR_WHOAMI_PB1200_DDR1:
+	case BCSR_WHOAMI_PB1200_DDR2:
+	case BCSR_WHOAMI_DB1200:
+		break;
+	default:
+		return -ENODEV;
+	}
+
+	printk(KERN_INFO "Alchemy/AMD/RMI %s Board, CPLD Rev %d"
+		"  Board-ID %d	Daughtercard ID %d\n", get_system_type(),
+		(whoami >> 4) & 0xf, (whoami >> 8) & 0xf, whoami & 0xf);
+
+	return 0;
+}
+
+/******************************************************************************/
+
+static u64 au1200_all_dmamask = DMA_BIT_MASK(32);
+
+static struct mtd_partition db1200_spiflash_parts[] = {
+	{
+		.name	= "spi_flash",
+		.offset = 0,
+		.size	= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct flash_platform_data db1200_spiflash_data = {
+	.name		= "s25fl001",
+	.parts		= db1200_spiflash_parts,
+	.nr_parts	= ARRAY_SIZE(db1200_spiflash_parts),
+	.type		= "m25p10",
+};
+
+static struct spi_board_info db1200_spi_devs[] __initdata = {
+	{
+		/* TI TMP121AIDBVR temp sensor */
+		.modalias	= "tmp121",
+		.max_speed_hz	= 2000000,
+		.bus_num	= 0,
+		.chip_select	= 0,
+		.mode		= 0,
+	},
+	{
+		/* Spansion S25FL001D0FMA SPI flash */
+		.modalias	= "m25p80",
+		.max_speed_hz	= 50000000,
+		.bus_num	= 0,
+		.chip_select	= 1,
+		.mode		= 0,
+		.platform_data	= &db1200_spiflash_data,
+	},
+};
+
+static struct i2c_board_info db1200_i2c_devs[] __initdata = {
+	{ I2C_BOARD_INFO("24c04", 0x52),  }, /* AT24C04-10 I2C eeprom */
+	{ I2C_BOARD_INFO("ne1619", 0x2d), }, /* adm1025-compat hwmon */
+	{ I2C_BOARD_INFO("wm8731", 0x1b), }, /* I2S audio codec WM8731 */
+};
+
+/**********************************************************************/
+
+static void au1200_nand_cmd_ctrl(struct nand_chip *this, int cmd,
+				 unsigned int ctrl)
+{
+	unsigned long ioaddr = (unsigned long)this->legacy.IO_ADDR_W;
+
+	ioaddr &= 0xffffff00;
+
+	if (ctrl & NAND_CLE) {
+		ioaddr += MEM_STNAND_CMD;
+	} else if (ctrl & NAND_ALE) {
+		ioaddr += MEM_STNAND_ADDR;
+	} else {
+		/* assume we want to r/w real data  by default */
+		ioaddr += MEM_STNAND_DATA;
+	}
+	this->legacy.IO_ADDR_R = this->legacy.IO_ADDR_W = (void __iomem *)ioaddr;
+	if (cmd != NAND_CMD_NONE) {
+		__raw_writeb(cmd, this->legacy.IO_ADDR_W);
+		wmb();
+	}
+}
+
+static int au1200_nand_device_ready(struct nand_chip *this)
+{
+	return alchemy_rdsmem(AU1000_MEM_STSTAT) & 1;
+}
+
+static struct mtd_partition db1200_nand_parts[] = {
+	{
+		.name	= "NAND FS 0",
+		.offset = 0,
+		.size	= 8 * 1024 * 1024,
+	},
+	{
+		.name	= "NAND FS 1",
+		.offset = MTDPART_OFS_APPEND,
+		.size	= MTDPART_SIZ_FULL
+	},
+};
+
+struct platform_nand_data db1200_nand_platdata = {
+	.chip = {
+		.nr_chips	= 1,
+		.chip_offset	= 0,
+		.nr_partitions	= ARRAY_SIZE(db1200_nand_parts),
+		.partitions	= db1200_nand_parts,
+		.chip_delay	= 20,
+	},
+	.ctrl = {
+		.dev_ready	= au1200_nand_device_ready,
+		.cmd_ctrl	= au1200_nand_cmd_ctrl,
+	},
+};
+
+static struct resource db1200_nand_res[] = {
+	[0] = {
+		.start	= DB1200_NAND_PHYS_ADDR,
+		.end	= DB1200_NAND_PHYS_ADDR + 0xff,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device db1200_nand_dev = {
+	.name		= "gen_nand",
+	.num_resources	= ARRAY_SIZE(db1200_nand_res),
+	.resource	= db1200_nand_res,
+	.id		= -1,
+	.dev		= {
+		.platform_data = &db1200_nand_platdata,
+	}
+};
+
+/**********************************************************************/
+
+static struct smc91x_platdata db1200_eth_data = {
+	.flags	= SMC91X_NOWAIT | SMC91X_USE_16BIT,
+	.leda	= RPC_LED_100_10,
+	.ledb	= RPC_LED_TX_RX,
+};
+
+static struct resource db1200_eth_res[] = {
+	[0] = {
+		.start	= DB1200_ETH_PHYS_ADDR,
+		.end	= DB1200_ETH_PHYS_ADDR + 0xf,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= DB1200_ETH_INT,
+		.end	= DB1200_ETH_INT,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device db1200_eth_dev = {
+	.dev	= {
+		.platform_data	= &db1200_eth_data,
+	},
+	.name		= "smc91x",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(db1200_eth_res),
+	.resource	= db1200_eth_res,
+};
+
+/**********************************************************************/
+
+static struct pata_platform_info db1200_ide_info = {
+	.ioport_shift	= DB1200_IDE_REG_SHIFT,
+};
+
+#define IDE_ALT_START	(14 << DB1200_IDE_REG_SHIFT)
+static struct resource db1200_ide_res[] = {
+	[0] = {
+		.start	= DB1200_IDE_PHYS_ADDR,
+		.end	= DB1200_IDE_PHYS_ADDR + IDE_ALT_START - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= DB1200_IDE_PHYS_ADDR + IDE_ALT_START,
+		.end	= DB1200_IDE_PHYS_ADDR + DB1200_IDE_PHYS_LEN - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[2] = {
+		.start	= DB1200_IDE_INT,
+		.end	= DB1200_IDE_INT,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device db1200_ide_dev = {
+	.name		= "pata_platform",
+	.id		= 0,
+	.dev = {
+		.dma_mask		= &au1200_all_dmamask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+		.platform_data		= &db1200_ide_info,
+	},
+	.num_resources	= ARRAY_SIZE(db1200_ide_res),
+	.resource	= db1200_ide_res,
+};
+
+/**********************************************************************/
+
+#ifdef CONFIG_MMC_AU1X
+/* SD carddetects:  they're supposed to be edge-triggered, but ack
+ * doesn't seem to work (CPLD Rev 2).  Instead, the screaming one
+ * is disabled and its counterpart enabled.  The 200ms timeout is
+ * because the carddetect usually triggers twice, after debounce.
+ */
+static irqreturn_t db1200_mmc_cd(int irq, void *ptr)
+{
+	disable_irq_nosync(irq);
+	return IRQ_WAKE_THREAD;
+}
+
+static irqreturn_t db1200_mmc_cdfn(int irq, void *ptr)
+{
+	mmc_detect_change(ptr, msecs_to_jiffies(200));
+
+	msleep(100);	/* debounce */
+	if (irq == DB1200_SD0_INSERT_INT)
+		enable_irq(DB1200_SD0_EJECT_INT);
+	else
+		enable_irq(DB1200_SD0_INSERT_INT);
+
+	return IRQ_HANDLED;
+}
+
+static int db1200_mmc_cd_setup(void *mmc_host, int en)
+{
+	int ret;
+
+	if (en) {
+		ret = request_threaded_irq(DB1200_SD0_INSERT_INT, db1200_mmc_cd,
+				db1200_mmc_cdfn, 0, "sd_insert", mmc_host);
+		if (ret)
+			goto out;
+
+		ret = request_threaded_irq(DB1200_SD0_EJECT_INT, db1200_mmc_cd,
+				db1200_mmc_cdfn, 0, "sd_eject", mmc_host);
+		if (ret) {
+			free_irq(DB1200_SD0_INSERT_INT, mmc_host);
+			goto out;
+		}
+
+		if (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD0INSERT)
+			enable_irq(DB1200_SD0_EJECT_INT);
+		else
+			enable_irq(DB1200_SD0_INSERT_INT);
+
+	} else {
+		free_irq(DB1200_SD0_INSERT_INT, mmc_host);
+		free_irq(DB1200_SD0_EJECT_INT, mmc_host);
+	}
+	ret = 0;
+out:
+	return ret;
+}
+
+static void db1200_mmc_set_power(void *mmc_host, int state)
+{
+	if (state) {
+		bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD0PWR);
+		msleep(400);	/* stabilization time */
+	} else
+		bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD0PWR, 0);
+}
+
+static int db1200_mmc_card_readonly(void *mmc_host)
+{
+	return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD0WP) ? 1 : 0;
+}
+
+static int db1200_mmc_card_inserted(void *mmc_host)
+{
+	return (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD0INSERT) ? 1 : 0;
+}
+
+static void db1200_mmcled_set(struct led_classdev *led,
+			      enum led_brightness brightness)
+{
+	if (brightness != LED_OFF)
+		bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED0, 0);
+	else
+		bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED0);
+}
+
+static struct led_classdev db1200_mmc_led = {
+	.brightness_set = db1200_mmcled_set,
+};
+
+/* -- */
+
+static irqreturn_t pb1200_mmc1_cd(int irq, void *ptr)
+{
+	disable_irq_nosync(irq);
+	return IRQ_WAKE_THREAD;
+}
+
+static irqreturn_t pb1200_mmc1_cdfn(int irq, void *ptr)
+{
+	mmc_detect_change(ptr, msecs_to_jiffies(200));
+
+	msleep(100);	/* debounce */
+	if (irq == PB1200_SD1_INSERT_INT)
+		enable_irq(PB1200_SD1_EJECT_INT);
+	else
+		enable_irq(PB1200_SD1_INSERT_INT);
+
+	return IRQ_HANDLED;
+}
+
+static int pb1200_mmc1_cd_setup(void *mmc_host, int en)
+{
+	int ret;
+
+	if (en) {
+		ret = request_threaded_irq(PB1200_SD1_INSERT_INT, pb1200_mmc1_cd,
+				pb1200_mmc1_cdfn, 0, "sd1_insert", mmc_host);
+		if (ret)
+			goto out;
+
+		ret = request_threaded_irq(PB1200_SD1_EJECT_INT, pb1200_mmc1_cd,
+				pb1200_mmc1_cdfn, 0, "sd1_eject", mmc_host);
+		if (ret) {
+			free_irq(PB1200_SD1_INSERT_INT, mmc_host);
+			goto out;
+		}
+
+		if (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD1INSERT)
+			enable_irq(PB1200_SD1_EJECT_INT);
+		else
+			enable_irq(PB1200_SD1_INSERT_INT);
+
+	} else {
+		free_irq(PB1200_SD1_INSERT_INT, mmc_host);
+		free_irq(PB1200_SD1_EJECT_INT, mmc_host);
+	}
+	ret = 0;
+out:
+	return ret;
+}
+
+static void pb1200_mmc1led_set(struct led_classdev *led,
+			enum led_brightness brightness)
+{
+	if (brightness != LED_OFF)
+			bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED1, 0);
+	else
+			bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED1);
+}
+
+static struct led_classdev pb1200_mmc1_led = {
+	.brightness_set = pb1200_mmc1led_set,
+};
+
+static void pb1200_mmc1_set_power(void *mmc_host, int state)
+{
+	if (state) {
+		bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD1PWR);
+		msleep(400);	/* stabilization time */
+	} else
+		bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD1PWR, 0);
+}
+
+static int pb1200_mmc1_card_readonly(void *mmc_host)
+{
+	return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD1WP) ? 1 : 0;
+}
+
+static int pb1200_mmc1_card_inserted(void *mmc_host)
+{
+	return (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD1INSERT) ? 1 : 0;
+}
+
+
+static struct au1xmmc_platform_data db1200_mmc_platdata[2] = {
+	[0] = {
+		.cd_setup	= db1200_mmc_cd_setup,
+		.set_power	= db1200_mmc_set_power,
+		.card_inserted	= db1200_mmc_card_inserted,
+		.card_readonly	= db1200_mmc_card_readonly,
+		.led		= &db1200_mmc_led,
+	},
+	[1] = {
+		.cd_setup	= pb1200_mmc1_cd_setup,
+		.set_power	= pb1200_mmc1_set_power,
+		.card_inserted	= pb1200_mmc1_card_inserted,
+		.card_readonly	= pb1200_mmc1_card_readonly,
+		.led		= &pb1200_mmc1_led,
+	},
+};
+
+static struct resource au1200_mmc0_resources[] = {
+	[0] = {
+		.start	= AU1100_SD0_PHYS_ADDR,
+		.end	= AU1100_SD0_PHYS_ADDR + 0xfff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AU1200_SD_INT,
+		.end	= AU1200_SD_INT,
+		.flags	= IORESOURCE_IRQ,
+	},
+	[2] = {
+		.start	= AU1200_DSCR_CMD0_SDMS_TX0,
+		.end	= AU1200_DSCR_CMD0_SDMS_TX0,
+		.flags	= IORESOURCE_DMA,
+	},
+	[3] = {
+		.start	= AU1200_DSCR_CMD0_SDMS_RX0,
+		.end	= AU1200_DSCR_CMD0_SDMS_RX0,
+		.flags	= IORESOURCE_DMA,
+	}
+};
+
+static struct platform_device db1200_mmc0_dev = {
+	.name		= "au1xxx-mmc",
+	.id		= 0,
+	.dev = {
+		.dma_mask		= &au1200_all_dmamask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+		.platform_data		= &db1200_mmc_platdata[0],
+	},
+	.num_resources	= ARRAY_SIZE(au1200_mmc0_resources),
+	.resource	= au1200_mmc0_resources,
+};
+
+static struct resource au1200_mmc1_res[] = {
+	[0] = {
+		.start	= AU1100_SD1_PHYS_ADDR,
+		.end	= AU1100_SD1_PHYS_ADDR + 0xfff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AU1200_SD_INT,
+		.end	= AU1200_SD_INT,
+		.flags	= IORESOURCE_IRQ,
+	},
+	[2] = {
+		.start	= AU1200_DSCR_CMD0_SDMS_TX1,
+		.end	= AU1200_DSCR_CMD0_SDMS_TX1,
+		.flags	= IORESOURCE_DMA,
+	},
+	[3] = {
+		.start	= AU1200_DSCR_CMD0_SDMS_RX1,
+		.end	= AU1200_DSCR_CMD0_SDMS_RX1,
+		.flags	= IORESOURCE_DMA,
+	}
+};
+
+static struct platform_device pb1200_mmc1_dev = {
+	.name		= "au1xxx-mmc",
+	.id		= 1,
+	.dev = {
+		.dma_mask		= &au1200_all_dmamask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+		.platform_data		= &db1200_mmc_platdata[1],
+	},
+	.num_resources	= ARRAY_SIZE(au1200_mmc1_res),
+	.resource	= au1200_mmc1_res,
+};
+#endif /* CONFIG_MMC_AU1X */
+
+/**********************************************************************/
+
+static int db1200fb_panel_index(void)
+{
+	return (bcsr_read(BCSR_SWITCHES) >> 8) & 0x0f;
+}
+
+static int db1200fb_panel_init(void)
+{
+	/* Apply power */
+	bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+				BCSR_BOARD_LCDBL);
+	return 0;
+}
+
+static int db1200fb_panel_shutdown(void)
+{
+	/* Remove power */
+	bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+			     BCSR_BOARD_LCDBL, 0);
+	return 0;
+}
+
+static struct au1200fb_platdata db1200fb_pd = {
+	.panel_index	= db1200fb_panel_index,
+	.panel_init	= db1200fb_panel_init,
+	.panel_shutdown = db1200fb_panel_shutdown,
+};
+
+static struct resource au1200_lcd_res[] = {
+	[0] = {
+		.start	= AU1200_LCD_PHYS_ADDR,
+		.end	= AU1200_LCD_PHYS_ADDR + 0x800 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AU1200_LCD_INT,
+		.end	= AU1200_LCD_INT,
+		.flags	= IORESOURCE_IRQ,
+	}
+};
+
+static struct platform_device au1200_lcd_dev = {
+	.name		= "au1200-lcd",
+	.id		= 0,
+	.dev = {
+		.dma_mask		= &au1200_all_dmamask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+		.platform_data		= &db1200fb_pd,
+	},
+	.num_resources	= ARRAY_SIZE(au1200_lcd_res),
+	.resource	= au1200_lcd_res,
+};
+
+/**********************************************************************/
+
+static struct resource au1200_psc0_res[] = {
+	[0] = {
+		.start	= AU1550_PSC0_PHYS_ADDR,
+		.end	= AU1550_PSC0_PHYS_ADDR + 0xfff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AU1200_PSC0_INT,
+		.end	= AU1200_PSC0_INT,
+		.flags	= IORESOURCE_IRQ,
+	},
+	[2] = {
+		.start	= AU1200_DSCR_CMD0_PSC0_TX,
+		.end	= AU1200_DSCR_CMD0_PSC0_TX,
+		.flags	= IORESOURCE_DMA,
+	},
+	[3] = {
+		.start	= AU1200_DSCR_CMD0_PSC0_RX,
+		.end	= AU1200_DSCR_CMD0_PSC0_RX,
+		.flags	= IORESOURCE_DMA,
+	},
+};
+
+static struct platform_device db1200_i2c_dev = {
+	.name		= "au1xpsc_smbus",
+	.id		= 0,	/* bus number */
+	.num_resources	= ARRAY_SIZE(au1200_psc0_res),
+	.resource	= au1200_psc0_res,
+};
+
+static void db1200_spi_cs_en(struct au1550_spi_info *spi, int cs, int pol)
+{
+	if (cs)
+		bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_SPISEL);
+	else
+		bcsr_mod(BCSR_RESETS, BCSR_RESETS_SPISEL, 0);
+}
+
+static struct au1550_spi_info db1200_spi_platdata = {
+	.mainclk_hz	= 50000000,	/* PSC0 clock */
+	.num_chipselect = 2,
+	.activate_cs	= db1200_spi_cs_en,
+};
+
+static struct platform_device db1200_spi_dev = {
+	.dev	= {
+		.dma_mask		= &au1200_all_dmamask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+		.platform_data		= &db1200_spi_platdata,
+	},
+	.name		= "au1550-spi",
+	.id		= 0,	/* bus number */
+	.num_resources	= ARRAY_SIZE(au1200_psc0_res),
+	.resource	= au1200_psc0_res,
+};
+
+static struct resource au1200_psc1_res[] = {
+	[0] = {
+		.start	= AU1550_PSC1_PHYS_ADDR,
+		.end	= AU1550_PSC1_PHYS_ADDR + 0xfff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AU1200_PSC1_INT,
+		.end	= AU1200_PSC1_INT,
+		.flags	= IORESOURCE_IRQ,
+	},
+	[2] = {
+		.start	= AU1200_DSCR_CMD0_PSC1_TX,
+		.end	= AU1200_DSCR_CMD0_PSC1_TX,
+		.flags	= IORESOURCE_DMA,
+	},
+	[3] = {
+		.start	= AU1200_DSCR_CMD0_PSC1_RX,
+		.end	= AU1200_DSCR_CMD0_PSC1_RX,
+		.flags	= IORESOURCE_DMA,
+	},
+};
+
+/* AC97 or I2S device */
+static struct platform_device db1200_audio_dev = {
+	/* name assigned later based on switch setting */
+	.id		= 1,	/* PSC ID */
+	.num_resources	= ARRAY_SIZE(au1200_psc1_res),
+	.resource	= au1200_psc1_res,
+};
+
+/* DB1200 ASoC card device */
+static struct platform_device db1200_sound_dev = {
+	/* name assigned later based on switch setting */
+	.id		= 1,	/* PSC ID */
+	.dev = {
+		.dma_mask		= &au1200_all_dmamask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+};
+
+static struct platform_device db1200_stac_dev = {
+	.name		= "ac97-codec",
+	.id		= 1,	/* on PSC1 */
+};
+
+static struct platform_device db1200_audiodma_dev = {
+	.name		= "au1xpsc-pcm",
+	.id		= 1,	/* PSC ID */
+};
+
+static struct platform_device *db1200_devs[] __initdata = {
+	NULL,		/* PSC0, selected by S6.8 */
+	&db1200_ide_dev,
+#ifdef CONFIG_MMC_AU1X
+	&db1200_mmc0_dev,
+#endif
+	&au1200_lcd_dev,
+	&db1200_eth_dev,
+	&db1200_nand_dev,
+	&db1200_audiodma_dev,
+	&db1200_audio_dev,
+	&db1200_stac_dev,
+	&db1200_sound_dev,
+};
+
+static struct platform_device *pb1200_devs[] __initdata = {
+#ifdef CONFIG_MMC_AU1X
+	&pb1200_mmc1_dev,
+#endif
+};
+
+/* Some peripheral base addresses differ on the PB1200 */
+static int __init pb1200_res_fixup(void)
+{
+	/* CPLD Revs earlier than 4 cause problems */
+	if (BCSR_WHOAMI_CPLD(bcsr_read(BCSR_WHOAMI)) <= 3) {
+		printk(KERN_ERR "WARNING!!!\n");
+		printk(KERN_ERR "WARNING!!!\n");
+		printk(KERN_ERR "PB1200 must be at CPLD rev 4. Please have\n");
+		printk(KERN_ERR "the board updated to latest revisions.\n");
+		printk(KERN_ERR "This software will not work reliably\n");
+		printk(KERN_ERR "on anything older than CPLD rev 4.!\n");
+		printk(KERN_ERR "WARNING!!!\n");
+		printk(KERN_ERR "WARNING!!!\n");
+		return 1;
+	}
+
+	db1200_nand_res[0].start = PB1200_NAND_PHYS_ADDR;
+	db1200_nand_res[0].end	 = PB1200_NAND_PHYS_ADDR + 0xff;
+	db1200_ide_res[0].start = PB1200_IDE_PHYS_ADDR;
+	db1200_ide_res[0].end	= PB1200_IDE_PHYS_ADDR + DB1200_IDE_PHYS_LEN - 1;
+	db1200_eth_res[0].start = PB1200_ETH_PHYS_ADDR;
+	db1200_eth_res[0].end	= PB1200_ETH_PHYS_ADDR + 0xff;
+	return 0;
+}
+
+int __init db1200_dev_setup(void)
+{
+	unsigned long pfc;
+	unsigned short sw;
+	int swapped, bid;
+	struct clk *c;
+
+	bid = BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI));
+	if ((bid == BCSR_WHOAMI_PB1200_DDR1) ||
+	    (bid == BCSR_WHOAMI_PB1200_DDR2)) {
+		if (pb1200_res_fixup())
+			return -ENODEV;
+	}
+
+	/* GPIO7 is low-level triggered CPLD cascade */
+	irq_set_irq_type(AU1200_GPIO7_INT, IRQ_TYPE_LEVEL_LOW);
+	bcsr_init_irq(DB1200_INT_BEGIN, DB1200_INT_END, AU1200_GPIO7_INT);
+
+	/* SMBus/SPI on PSC0, Audio on PSC1 */
+	pfc = alchemy_rdsys(AU1000_SYS_PINFUNC);
+	pfc &= ~(SYS_PINFUNC_P0A | SYS_PINFUNC_P0B);
+	pfc &= ~(SYS_PINFUNC_P1A | SYS_PINFUNC_P1B | SYS_PINFUNC_FS3);
+	pfc |= SYS_PINFUNC_P1C; /* SPI is configured later */
+	alchemy_wrsys(pfc, AU1000_SYS_PINFUNC);
+
+	/* get 50MHz for I2C driver on PSC0 */
+	c = clk_get(NULL, "psc0_intclk");
+	if (!IS_ERR(c)) {
+		pfc = clk_round_rate(c, 50000000);
+		if ((pfc < 1) || (abs(50000000 - pfc) > 2500000))
+			pr_warn("DB1200: can't get I2C close to 50MHz\n");
+		else
+			clk_set_rate(c, pfc);
+		clk_prepare_enable(c);
+		clk_put(c);
+	}
+
+	/* insert/eject pairs: one of both is always screaming.	 To avoid
+	 * issues they must not be automatically enabled when initially
+	 * requested.
+	 */
+	irq_set_status_flags(DB1200_SD0_INSERT_INT, IRQ_NOAUTOEN);
+	irq_set_status_flags(DB1200_SD0_EJECT_INT, IRQ_NOAUTOEN);
+	irq_set_status_flags(DB1200_PC0_INSERT_INT, IRQ_NOAUTOEN);
+	irq_set_status_flags(DB1200_PC0_EJECT_INT, IRQ_NOAUTOEN);
+	irq_set_status_flags(DB1200_PC1_INSERT_INT, IRQ_NOAUTOEN);
+	irq_set_status_flags(DB1200_PC1_EJECT_INT, IRQ_NOAUTOEN);
+
+	i2c_register_board_info(0, db1200_i2c_devs,
+				ARRAY_SIZE(db1200_i2c_devs));
+	spi_register_board_info(db1200_spi_devs,
+				ARRAY_SIZE(db1200_spi_devs));
+
+	/* SWITCHES:	S6.8 I2C/SPI selector  (OFF=I2C	 ON=SPI)
+	 *		S6.7 AC97/I2S selector (OFF=AC97 ON=I2S)
+	 *		or S12 on the PB1200.
+	 */
+
+	/* NOTE: GPIO215 controls OTG VBUS supply.  In SPI mode however
+	 * this pin is claimed by PSC0 (unused though, but pinmux doesn't
+	 * allow to free it without crippling the SPI interface).
+	 * As a result, in SPI mode, OTG simply won't work (PSC0 uses
+	 * it as an input pin which is pulled high on the boards).
+	 */
+	pfc = alchemy_rdsys(AU1000_SYS_PINFUNC) & ~SYS_PINFUNC_P0A;
+
+	/* switch off OTG VBUS supply */
+	gpio_request(215, "otg-vbus");
+	gpio_direction_output(215, 1);
+
+	printk(KERN_INFO "%s device configuration:\n", get_system_type());
+
+	sw = bcsr_read(BCSR_SWITCHES);
+	if (sw & BCSR_SWITCHES_DIP_8) {
+		db1200_devs[0] = &db1200_i2c_dev;
+		bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC0MUX, 0);
+
+		pfc |= (2 << 17);	/* GPIO2 block owns GPIO215 */
+
+		printk(KERN_INFO " S6.8 OFF: PSC0 mode I2C\n");
+		printk(KERN_INFO "   OTG port VBUS supply available!\n");
+	} else {
+		db1200_devs[0] = &db1200_spi_dev;
+		bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_PSC0MUX);
+
+		pfc |= (1 << 17);	/* PSC0 owns GPIO215 */
+
+		printk(KERN_INFO " S6.8 ON : PSC0 mode SPI\n");
+		printk(KERN_INFO "   OTG port VBUS supply disabled\n");
+	}
+	alchemy_wrsys(pfc, AU1000_SYS_PINFUNC);
+
+	/* Audio: DIP7 selects I2S(0)/AC97(1), but need I2C for I2S!
+	 * so: DIP7=1 || DIP8=0 => AC97, DIP7=0 && DIP8=1 => I2S
+	 */
+	sw &= BCSR_SWITCHES_DIP_8 | BCSR_SWITCHES_DIP_7;
+	if (sw == BCSR_SWITCHES_DIP_8) {
+		bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_PSC1MUX);
+		db1200_audio_dev.name = "au1xpsc_i2s";
+		db1200_sound_dev.name = "db1200-i2s";
+		printk(KERN_INFO " S6.7 ON : PSC1 mode I2S\n");
+	} else {
+		bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC1MUX, 0);
+		db1200_audio_dev.name = "au1xpsc_ac97";
+		db1200_sound_dev.name = "db1200-ac97";
+		printk(KERN_INFO " S6.7 OFF: PSC1 mode AC97\n");
+	}
+
+	/* Audio PSC clock is supplied externally. (FIXME: platdata!!) */
+	__raw_writel(PSC_SEL_CLK_SERCLK,
+	    (void __iomem *)KSEG1ADDR(AU1550_PSC1_PHYS_ADDR) + PSC_SEL_OFFSET);
+	wmb();
+
+	db1x_register_pcmcia_socket(
+		AU1000_PCMCIA_ATTR_PHYS_ADDR,
+		AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+		AU1000_PCMCIA_MEM_PHYS_ADDR,
+		AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x000400000 - 1,
+		AU1000_PCMCIA_IO_PHYS_ADDR,
+		AU1000_PCMCIA_IO_PHYS_ADDR   + 0x000010000 - 1,
+		DB1200_PC0_INT, DB1200_PC0_INSERT_INT,
+		/*DB1200_PC0_STSCHG_INT*/0, DB1200_PC0_EJECT_INT, 0);
+
+	db1x_register_pcmcia_socket(
+		AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
+		AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
+		AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x004000000,
+		AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x004400000 - 1,
+		AU1000_PCMCIA_IO_PHYS_ADDR   + 0x004000000,
+		AU1000_PCMCIA_IO_PHYS_ADDR   + 0x004010000 - 1,
+		DB1200_PC1_INT, DB1200_PC1_INSERT_INT,
+		/*DB1200_PC1_STSCHG_INT*/0, DB1200_PC1_EJECT_INT, 1);
+
+	swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1200_SWAPBOOT;
+	db1x_register_norflash(64 << 20, 2, swapped);
+
+	platform_add_devices(db1200_devs, ARRAY_SIZE(db1200_devs));
+
+	/* PB1200 is a DB1200 with a 2nd MMC and Camera connector */
+	if ((bid == BCSR_WHOAMI_PB1200_DDR1) ||
+	    (bid == BCSR_WHOAMI_PB1200_DDR2))
+		platform_add_devices(pb1200_devs, ARRAY_SIZE(pb1200_devs));
+
+	return 0;
+}
diff --git a/arch/mips/alchemy/devboards/db1300.c b/arch/mips/alchemy/devboards/db1300.c
new file mode 100644
index 000000000..d377e043b
--- /dev/null
+++ b/arch/mips/alchemy/devboards/db1300.c
@@ -0,0 +1,879 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * DBAu1300 init and platform device setup.
+ *
+ * (c) 2009 Manuel Lauss <manuel.lauss@googlemail.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
+#include <linux/gpio_keys.h>
+#include <linux/init.h>
+#include <linux/input.h>	/* KEY_* codes */
+#include <linux/i2c.h>
+#include <linux/io.h>
+#include <linux/leds.h>
+#include <linux/interrupt.h>
+#include <linux/ata_platform.h>
+#include <linux/mmc/host.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/platnand.h>
+#include <linux/platform_device.h>
+#include <linux/smsc911x.h>
+#include <linux/wm97xx.h>
+
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/gpio-au1300.h>
+#include <asm/mach-au1x00/au1100_mmc.h>
+#include <asm/mach-au1x00/au1200fb.h>
+#include <asm/mach-au1x00/au1xxx_dbdma.h>
+#include <asm/mach-au1x00/au1xxx_psc.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <asm/mach-au1x00/prom.h>
+
+#include "platform.h"
+
+/* FPGA (external mux) interrupt sources */
+#define DB1300_FIRST_INT	(ALCHEMY_GPIC_INT_LAST + 1)
+#define DB1300_IDE_INT		(DB1300_FIRST_INT + 0)
+#define DB1300_ETH_INT		(DB1300_FIRST_INT + 1)
+#define DB1300_CF_INT		(DB1300_FIRST_INT + 2)
+#define DB1300_VIDEO_INT	(DB1300_FIRST_INT + 4)
+#define DB1300_HDMI_INT		(DB1300_FIRST_INT + 5)
+#define DB1300_DC_INT		(DB1300_FIRST_INT + 6)
+#define DB1300_FLASH_INT	(DB1300_FIRST_INT + 7)
+#define DB1300_CF_INSERT_INT	(DB1300_FIRST_INT + 8)
+#define DB1300_CF_EJECT_INT	(DB1300_FIRST_INT + 9)
+#define DB1300_AC97_INT		(DB1300_FIRST_INT + 10)
+#define DB1300_AC97_PEN_INT	(DB1300_FIRST_INT + 11)
+#define DB1300_SD1_INSERT_INT	(DB1300_FIRST_INT + 12)
+#define DB1300_SD1_EJECT_INT	(DB1300_FIRST_INT + 13)
+#define DB1300_OTG_VBUS_OC_INT	(DB1300_FIRST_INT + 14)
+#define DB1300_HOST_VBUS_OC_INT (DB1300_FIRST_INT + 15)
+#define DB1300_LAST_INT		(DB1300_FIRST_INT + 15)
+
+/* SMSC9210 CS */
+#define DB1300_ETH_PHYS_ADDR	0x19000000
+#define DB1300_ETH_PHYS_END	0x197fffff
+
+/* ATA CS */
+#define DB1300_IDE_PHYS_ADDR	0x18800000
+#define DB1300_IDE_REG_SHIFT	5
+#define DB1300_IDE_PHYS_LEN	(16 << DB1300_IDE_REG_SHIFT)
+
+/* NAND CS */
+#define DB1300_NAND_PHYS_ADDR	0x20000000
+#define DB1300_NAND_PHYS_END	0x20000fff
+
+
+static struct i2c_board_info db1300_i2c_devs[] __initdata = {
+	{ I2C_BOARD_INFO("wm8731", 0x1b), },	/* I2S audio codec */
+	{ I2C_BOARD_INFO("ne1619", 0x2d), },	/* adm1025-compat hwmon */
+};
+
+/* multifunction pins to assign to GPIO controller */
+static int db1300_gpio_pins[] __initdata = {
+	AU1300_PIN_LCDPWM0, AU1300_PIN_PSC2SYNC1, AU1300_PIN_WAKE1,
+	AU1300_PIN_WAKE2, AU1300_PIN_WAKE3, AU1300_PIN_FG3AUX,
+	AU1300_PIN_EXTCLK1,
+	-1,	/* terminator */
+};
+
+/* multifunction pins to assign to device functions */
+static int db1300_dev_pins[] __initdata = {
+	/* wake-from-str pins 0-3 */
+	AU1300_PIN_WAKE0,
+	/* external clock sources for PSC0 */
+	AU1300_PIN_EXTCLK0,
+	/* 8bit MMC interface on SD0: 6-9 */
+	AU1300_PIN_SD0DAT4, AU1300_PIN_SD0DAT5, AU1300_PIN_SD0DAT6,
+	AU1300_PIN_SD0DAT7,
+	/* UART1 pins: 11-18 */
+	AU1300_PIN_U1RI, AU1300_PIN_U1DCD, AU1300_PIN_U1DSR,
+	AU1300_PIN_U1CTS, AU1300_PIN_U1RTS, AU1300_PIN_U1DTR,
+	AU1300_PIN_U1RX, AU1300_PIN_U1TX,
+	/* UART0 pins: 19-24 */
+	AU1300_PIN_U0RI, AU1300_PIN_U0DCD, AU1300_PIN_U0DSR,
+	AU1300_PIN_U0CTS, AU1300_PIN_U0RTS, AU1300_PIN_U0DTR,
+	/* UART2: 25-26 */
+	AU1300_PIN_U2RX, AU1300_PIN_U2TX,
+	/* UART3: 27-28 */
+	AU1300_PIN_U3RX, AU1300_PIN_U3TX,
+	/* LCD controller PWMs, ext pixclock: 30-31 */
+	AU1300_PIN_LCDPWM1, AU1300_PIN_LCDCLKIN,
+	/* SD1 interface: 32-37 */
+	AU1300_PIN_SD1DAT0, AU1300_PIN_SD1DAT1, AU1300_PIN_SD1DAT2,
+	AU1300_PIN_SD1DAT3, AU1300_PIN_SD1CMD, AU1300_PIN_SD1CLK,
+	/* SD2 interface: 38-43 */
+	AU1300_PIN_SD2DAT0, AU1300_PIN_SD2DAT1, AU1300_PIN_SD2DAT2,
+	AU1300_PIN_SD2DAT3, AU1300_PIN_SD2CMD, AU1300_PIN_SD2CLK,
+	/* PSC0/1 clocks: 44-45 */
+	AU1300_PIN_PSC0CLK, AU1300_PIN_PSC1CLK,
+	/* PSCs: 46-49/50-53/54-57/58-61 */
+	AU1300_PIN_PSC0SYNC0, AU1300_PIN_PSC0SYNC1, AU1300_PIN_PSC0D0,
+	AU1300_PIN_PSC0D1,
+	AU1300_PIN_PSC1SYNC0, AU1300_PIN_PSC1SYNC1, AU1300_PIN_PSC1D0,
+	AU1300_PIN_PSC1D1,
+	AU1300_PIN_PSC2SYNC0,			    AU1300_PIN_PSC2D0,
+	AU1300_PIN_PSC2D1,
+	AU1300_PIN_PSC3SYNC0, AU1300_PIN_PSC3SYNC1, AU1300_PIN_PSC3D0,
+	AU1300_PIN_PSC3D1,
+	/* PCMCIA interface: 62-70 */
+	AU1300_PIN_PCE2, AU1300_PIN_PCE1, AU1300_PIN_PIOS16,
+	AU1300_PIN_PIOR, AU1300_PIN_PWE, AU1300_PIN_PWAIT,
+	AU1300_PIN_PREG, AU1300_PIN_POE, AU1300_PIN_PIOW,
+	/* camera interface H/V sync inputs: 71-72 */
+	AU1300_PIN_CIMLS, AU1300_PIN_CIMFS,
+	/* PSC2/3 clocks: 73-74 */
+	AU1300_PIN_PSC2CLK, AU1300_PIN_PSC3CLK,
+	-1,	/* terminator */
+};
+
+static void __init db1300_gpio_config(void)
+{
+	int *i;
+
+	i = &db1300_dev_pins[0];
+	while (*i != -1)
+		au1300_pinfunc_to_dev(*i++);
+
+	i = &db1300_gpio_pins[0];
+	while (*i != -1)
+		au1300_gpio_direction_input(*i++);/* implies pin_to_gpio */
+
+	au1300_set_dbdma_gpio(1, AU1300_PIN_FG3AUX);
+}
+
+/**********************************************************************/
+
+static u64 au1300_all_dmamask = DMA_BIT_MASK(32);
+
+static void au1300_nand_cmd_ctrl(struct nand_chip *this, int cmd,
+				 unsigned int ctrl)
+{
+	unsigned long ioaddr = (unsigned long)this->legacy.IO_ADDR_W;
+
+	ioaddr &= 0xffffff00;
+
+	if (ctrl & NAND_CLE) {
+		ioaddr += MEM_STNAND_CMD;
+	} else if (ctrl & NAND_ALE) {
+		ioaddr += MEM_STNAND_ADDR;
+	} else {
+		/* assume we want to r/w real data  by default */
+		ioaddr += MEM_STNAND_DATA;
+	}
+	this->legacy.IO_ADDR_R = this->legacy.IO_ADDR_W = (void __iomem *)ioaddr;
+	if (cmd != NAND_CMD_NONE) {
+		__raw_writeb(cmd, this->legacy.IO_ADDR_W);
+		wmb();
+	}
+}
+
+static int au1300_nand_device_ready(struct nand_chip *this)
+{
+	return alchemy_rdsmem(AU1000_MEM_STSTAT) & 1;
+}
+
+static struct mtd_partition db1300_nand_parts[] = {
+	{
+		.name	= "NAND FS 0",
+		.offset = 0,
+		.size	= 8 * 1024 * 1024,
+	},
+	{
+		.name	= "NAND FS 1",
+		.offset = MTDPART_OFS_APPEND,
+		.size	= MTDPART_SIZ_FULL
+	},
+};
+
+struct platform_nand_data db1300_nand_platdata = {
+	.chip = {
+		.nr_chips	= 1,
+		.chip_offset	= 0,
+		.nr_partitions	= ARRAY_SIZE(db1300_nand_parts),
+		.partitions	= db1300_nand_parts,
+		.chip_delay	= 20,
+	},
+	.ctrl = {
+		.dev_ready	= au1300_nand_device_ready,
+		.cmd_ctrl	= au1300_nand_cmd_ctrl,
+	},
+};
+
+static struct resource db1300_nand_res[] = {
+	[0] = {
+		.start	= DB1300_NAND_PHYS_ADDR,
+		.end	= DB1300_NAND_PHYS_ADDR + 0xff,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device db1300_nand_dev = {
+	.name		= "gen_nand",
+	.num_resources	= ARRAY_SIZE(db1300_nand_res),
+	.resource	= db1300_nand_res,
+	.id		= -1,
+	.dev		= {
+		.platform_data = &db1300_nand_platdata,
+	}
+};
+
+/**********************************************************************/
+
+static struct resource db1300_eth_res[] = {
+	[0] = {
+		.start		= DB1300_ETH_PHYS_ADDR,
+		.end		= DB1300_ETH_PHYS_END,
+		.flags		= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start		= DB1300_ETH_INT,
+		.end		= DB1300_ETH_INT,
+		.flags		= IORESOURCE_IRQ,
+	},
+};
+
+static struct smsc911x_platform_config db1300_eth_config = {
+	.phy_interface		= PHY_INTERFACE_MODE_MII,
+	.irq_polarity		= SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
+	.irq_type		= SMSC911X_IRQ_TYPE_PUSH_PULL,
+	.flags			= SMSC911X_USE_32BIT,
+};
+
+static struct platform_device db1300_eth_dev = {
+	.name			= "smsc911x",
+	.id			= -1,
+	.num_resources		= ARRAY_SIZE(db1300_eth_res),
+	.resource		= db1300_eth_res,
+	.dev = {
+		.platform_data	= &db1300_eth_config,
+	},
+};
+
+/**********************************************************************/
+
+static struct resource au1300_psc1_res[] = {
+	[0] = {
+		.start	= AU1300_PSC1_PHYS_ADDR,
+		.end	= AU1300_PSC1_PHYS_ADDR + 0x0fff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AU1300_PSC1_INT,
+		.end	= AU1300_PSC1_INT,
+		.flags	= IORESOURCE_IRQ,
+	},
+	[2] = {
+		.start	= AU1300_DSCR_CMD0_PSC1_TX,
+		.end	= AU1300_DSCR_CMD0_PSC1_TX,
+		.flags	= IORESOURCE_DMA,
+	},
+	[3] = {
+		.start	= AU1300_DSCR_CMD0_PSC1_RX,
+		.end	= AU1300_DSCR_CMD0_PSC1_RX,
+		.flags	= IORESOURCE_DMA,
+	},
+};
+
+static struct platform_device db1300_ac97_dev = {
+	.name		= "au1xpsc_ac97",
+	.id		= 1,	/* PSC ID. match with AC97 codec ID! */
+	.num_resources	= ARRAY_SIZE(au1300_psc1_res),
+	.resource	= au1300_psc1_res,
+};
+
+/**********************************************************************/
+
+static struct resource au1300_psc2_res[] = {
+	[0] = {
+		.start	= AU1300_PSC2_PHYS_ADDR,
+		.end	= AU1300_PSC2_PHYS_ADDR + 0x0fff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AU1300_PSC2_INT,
+		.end	= AU1300_PSC2_INT,
+		.flags	= IORESOURCE_IRQ,
+	},
+	[2] = {
+		.start	= AU1300_DSCR_CMD0_PSC2_TX,
+		.end	= AU1300_DSCR_CMD0_PSC2_TX,
+		.flags	= IORESOURCE_DMA,
+	},
+	[3] = {
+		.start	= AU1300_DSCR_CMD0_PSC2_RX,
+		.end	= AU1300_DSCR_CMD0_PSC2_RX,
+		.flags	= IORESOURCE_DMA,
+	},
+};
+
+static struct platform_device db1300_i2s_dev = {
+	.name		= "au1xpsc_i2s",
+	.id		= 2,	/* PSC ID */
+	.num_resources	= ARRAY_SIZE(au1300_psc2_res),
+	.resource	= au1300_psc2_res,
+};
+
+/**********************************************************************/
+
+static struct resource au1300_psc3_res[] = {
+	[0] = {
+		.start	= AU1300_PSC3_PHYS_ADDR,
+		.end	= AU1300_PSC3_PHYS_ADDR + 0x0fff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AU1300_PSC3_INT,
+		.end	= AU1300_PSC3_INT,
+		.flags	= IORESOURCE_IRQ,
+	},
+	[2] = {
+		.start	= AU1300_DSCR_CMD0_PSC3_TX,
+		.end	= AU1300_DSCR_CMD0_PSC3_TX,
+		.flags	= IORESOURCE_DMA,
+	},
+	[3] = {
+		.start	= AU1300_DSCR_CMD0_PSC3_RX,
+		.end	= AU1300_DSCR_CMD0_PSC3_RX,
+		.flags	= IORESOURCE_DMA,
+	},
+};
+
+static struct platform_device db1300_i2c_dev = {
+	.name		= "au1xpsc_smbus",
+	.id		= 0,	/* bus number */
+	.num_resources	= ARRAY_SIZE(au1300_psc3_res),
+	.resource	= au1300_psc3_res,
+};
+
+/**********************************************************************/
+
+/* proper key assignments when facing the LCD panel.  For key assignments
+ * according to the schematics swap up with down and left with right.
+ * I chose to use it to emulate the arrow keys of a keyboard.
+ */
+static struct gpio_keys_button db1300_5waysw_arrowkeys[] = {
+	{
+		.code			= KEY_DOWN,
+		.gpio			= AU1300_PIN_LCDPWM0,
+		.type			= EV_KEY,
+		.debounce_interval	= 1,
+		.active_low		= 1,
+		.desc			= "5waysw-down",
+	},
+	{
+		.code			= KEY_UP,
+		.gpio			= AU1300_PIN_PSC2SYNC1,
+		.type			= EV_KEY,
+		.debounce_interval	= 1,
+		.active_low		= 1,
+		.desc			= "5waysw-up",
+	},
+	{
+		.code			= KEY_RIGHT,
+		.gpio			= AU1300_PIN_WAKE3,
+		.type			= EV_KEY,
+		.debounce_interval	= 1,
+		.active_low		= 1,
+		.desc			= "5waysw-right",
+	},
+	{
+		.code			= KEY_LEFT,
+		.gpio			= AU1300_PIN_WAKE2,
+		.type			= EV_KEY,
+		.debounce_interval	= 1,
+		.active_low		= 1,
+		.desc			= "5waysw-left",
+	},
+	{
+		.code			= KEY_ENTER,
+		.gpio			= AU1300_PIN_WAKE1,
+		.type			= EV_KEY,
+		.debounce_interval	= 1,
+		.active_low		= 1,
+		.desc			= "5waysw-push",
+	},
+};
+
+static struct gpio_keys_platform_data db1300_5waysw_data = {
+	.buttons	= db1300_5waysw_arrowkeys,
+	.nbuttons	= ARRAY_SIZE(db1300_5waysw_arrowkeys),
+	.rep		= 1,
+	.name		= "db1300-5wayswitch",
+};
+
+static struct platform_device db1300_5waysw_dev = {
+	.name		= "gpio-keys",
+	.dev	= {
+		.platform_data	= &db1300_5waysw_data,
+	},
+};
+
+/**********************************************************************/
+
+static struct pata_platform_info db1300_ide_info = {
+	.ioport_shift	= DB1300_IDE_REG_SHIFT,
+};
+
+#define IDE_ALT_START	(14 << DB1300_IDE_REG_SHIFT)
+static struct resource db1300_ide_res[] = {
+	[0] = {
+		.start	= DB1300_IDE_PHYS_ADDR,
+		.end	= DB1300_IDE_PHYS_ADDR + IDE_ALT_START - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= DB1300_IDE_PHYS_ADDR + IDE_ALT_START,
+		.end	= DB1300_IDE_PHYS_ADDR + DB1300_IDE_PHYS_LEN - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[2] = {
+		.start	= DB1300_IDE_INT,
+		.end	= DB1300_IDE_INT,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device db1300_ide_dev = {
+	.dev	= {
+		.dma_mask		= &au1300_all_dmamask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+		.platform_data	= &db1300_ide_info,
+	},
+	.name		= "pata_platform",
+	.resource	= db1300_ide_res,
+	.num_resources	= ARRAY_SIZE(db1300_ide_res),
+};
+
+/**********************************************************************/
+
+#ifdef CONFIG_MMC_AU1X
+static irqreturn_t db1300_mmc_cd(int irq, void *ptr)
+{
+	disable_irq_nosync(irq);
+	return IRQ_WAKE_THREAD;
+}
+
+static irqreturn_t db1300_mmc_cdfn(int irq, void *ptr)
+{
+	mmc_detect_change(ptr, msecs_to_jiffies(200));
+
+	msleep(100);	/* debounce */
+	if (irq == DB1300_SD1_INSERT_INT)
+		enable_irq(DB1300_SD1_EJECT_INT);
+	else
+		enable_irq(DB1300_SD1_INSERT_INT);
+
+	return IRQ_HANDLED;
+}
+
+static int db1300_mmc_card_readonly(void *mmc_host)
+{
+	/* it uses SD1 interface, but the DB1200's SD0 bit in the CPLD */
+	return bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD0WP;
+}
+
+static int db1300_mmc_card_inserted(void *mmc_host)
+{
+	return bcsr_read(BCSR_SIGSTAT) & (1 << 12); /* insertion irq signal */
+}
+
+static int db1300_mmc_cd_setup(void *mmc_host, int en)
+{
+	int ret;
+
+	if (en) {
+		ret = request_threaded_irq(DB1300_SD1_INSERT_INT, db1300_mmc_cd,
+				db1300_mmc_cdfn, 0, "sd_insert", mmc_host);
+		if (ret)
+			goto out;
+
+		ret = request_threaded_irq(DB1300_SD1_EJECT_INT, db1300_mmc_cd,
+				db1300_mmc_cdfn, 0, "sd_eject", mmc_host);
+		if (ret) {
+			free_irq(DB1300_SD1_INSERT_INT, mmc_host);
+			goto out;
+		}
+
+		if (db1300_mmc_card_inserted(mmc_host))
+			enable_irq(DB1300_SD1_EJECT_INT);
+		else
+			enable_irq(DB1300_SD1_INSERT_INT);
+
+	} else {
+		free_irq(DB1300_SD1_INSERT_INT, mmc_host);
+		free_irq(DB1300_SD1_EJECT_INT, mmc_host);
+	}
+	ret = 0;
+out:
+	return ret;
+}
+
+static void db1300_mmcled_set(struct led_classdev *led,
+			      enum led_brightness brightness)
+{
+	if (brightness != LED_OFF)
+		bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED0, 0);
+	else
+		bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED0);
+}
+
+static struct led_classdev db1300_mmc_led = {
+	.brightness_set = db1300_mmcled_set,
+};
+
+struct au1xmmc_platform_data db1300_sd1_platdata = {
+	.cd_setup	= db1300_mmc_cd_setup,
+	.card_inserted	= db1300_mmc_card_inserted,
+	.card_readonly	= db1300_mmc_card_readonly,
+	.led		= &db1300_mmc_led,
+};
+
+static struct resource au1300_sd1_res[] = {
+	[0] = {
+		.start	= AU1300_SD1_PHYS_ADDR,
+		.end	= AU1300_SD1_PHYS_ADDR,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AU1300_SD1_INT,
+		.end	= AU1300_SD1_INT,
+		.flags	= IORESOURCE_IRQ,
+	},
+	[2] = {
+		.start	= AU1300_DSCR_CMD0_SDMS_TX1,
+		.end	= AU1300_DSCR_CMD0_SDMS_TX1,
+		.flags	= IORESOURCE_DMA,
+	},
+	[3] = {
+		.start	= AU1300_DSCR_CMD0_SDMS_RX1,
+		.end	= AU1300_DSCR_CMD0_SDMS_RX1,
+		.flags	= IORESOURCE_DMA,
+	},
+};
+
+static struct platform_device db1300_sd1_dev = {
+	.dev = {
+		.dma_mask		= &au1300_all_dmamask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+		.platform_data		= &db1300_sd1_platdata,
+	},
+	.name		= "au1xxx-mmc",
+	.id		= 1,
+	.resource	= au1300_sd1_res,
+	.num_resources	= ARRAY_SIZE(au1300_sd1_res),
+};
+
+/**********************************************************************/
+
+static int db1300_movinand_inserted(void *mmc_host)
+{
+	return 0; /* disable for now, it doesn't work yet */
+}
+
+static int db1300_movinand_readonly(void *mmc_host)
+{
+	return 0;
+}
+
+static void db1300_movinand_led_set(struct led_classdev *led,
+				    enum led_brightness brightness)
+{
+	if (brightness != LED_OFF)
+		bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED1, 0);
+	else
+		bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED1);
+}
+
+static struct led_classdev db1300_movinand_led = {
+	.brightness_set		= db1300_movinand_led_set,
+};
+
+struct au1xmmc_platform_data db1300_sd0_platdata = {
+	.card_inserted		= db1300_movinand_inserted,
+	.card_readonly		= db1300_movinand_readonly,
+	.led			= &db1300_movinand_led,
+	.mask_host_caps		= MMC_CAP_NEEDS_POLL,
+};
+
+static struct resource au1300_sd0_res[] = {
+	[0] = {
+		.start	= AU1100_SD0_PHYS_ADDR,
+		.end	= AU1100_SD0_PHYS_ADDR,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AU1300_SD0_INT,
+		.end	= AU1300_SD0_INT,
+		.flags	= IORESOURCE_IRQ,
+	},
+	[2] = {
+		.start	= AU1300_DSCR_CMD0_SDMS_TX0,
+		.end	= AU1300_DSCR_CMD0_SDMS_TX0,
+		.flags	= IORESOURCE_DMA,
+	},
+	[3] = {
+		.start	= AU1300_DSCR_CMD0_SDMS_RX0,
+		.end	= AU1300_DSCR_CMD0_SDMS_RX0,
+		.flags	= IORESOURCE_DMA,
+	},
+};
+
+static struct platform_device db1300_sd0_dev = {
+	.dev = {
+		.dma_mask		= &au1300_all_dmamask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+		.platform_data		= &db1300_sd0_platdata,
+	},
+	.name		= "au1xxx-mmc",
+	.id		= 0,
+	.resource	= au1300_sd0_res,
+	.num_resources	= ARRAY_SIZE(au1300_sd0_res),
+};
+#endif /* CONFIG_MMC_AU1X */
+
+/**********************************************************************/
+
+static struct platform_device db1300_wm9715_dev = {
+	.name		= "wm9712-codec",
+	.id		= 1,	/* ID of PSC for AC97 audio, see asoc glue! */
+};
+
+static struct platform_device db1300_ac97dma_dev = {
+	.name		= "au1xpsc-pcm",
+	.id		= 1,	/* PSC ID */
+};
+
+static struct platform_device db1300_i2sdma_dev = {
+	.name		= "au1xpsc-pcm",
+	.id		= 2,	/* PSC ID */
+};
+
+static struct platform_device db1300_sndac97_dev = {
+	.name		= "db1300-ac97",
+	.dev = {
+		.dma_mask		= &au1300_all_dmamask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+};
+
+static struct platform_device db1300_sndi2s_dev = {
+	.name		= "db1300-i2s",
+	.dev = {
+		.dma_mask		= &au1300_all_dmamask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+};
+
+/**********************************************************************/
+
+static int db1300fb_panel_index(void)
+{
+	return 9;	/* DB1300_800x480 */
+}
+
+static int db1300fb_panel_init(void)
+{
+	/* Apply power (Vee/Vdd logic is inverted on Panel DB1300_800x480) */
+	bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD,
+			     BCSR_BOARD_LCDBL);
+	return 0;
+}
+
+static int db1300fb_panel_shutdown(void)
+{
+	/* Remove power (Vee/Vdd logic is inverted on Panel DB1300_800x480) */
+	bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDBL,
+			     BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD);
+	return 0;
+}
+
+static struct au1200fb_platdata db1300fb_pd = {
+	.panel_index	= db1300fb_panel_index,
+	.panel_init	= db1300fb_panel_init,
+	.panel_shutdown = db1300fb_panel_shutdown,
+};
+
+static struct resource au1300_lcd_res[] = {
+	[0] = {
+		.start	= AU1200_LCD_PHYS_ADDR,
+		.end	= AU1200_LCD_PHYS_ADDR + 0x800 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AU1300_LCD_INT,
+		.end	= AU1300_LCD_INT,
+		.flags	= IORESOURCE_IRQ,
+	}
+};
+
+
+static struct platform_device db1300_lcd_dev = {
+	.name		= "au1200-lcd",
+	.id		= 0,
+	.dev = {
+		.dma_mask		= &au1300_all_dmamask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+		.platform_data		= &db1300fb_pd,
+	},
+	.num_resources	= ARRAY_SIZE(au1300_lcd_res),
+	.resource	= au1300_lcd_res,
+};
+
+/**********************************************************************/
+
+#if IS_ENABLED(CONFIG_TOUCHSCREEN_WM97XX)
+static struct wm97xx_mach_ops db1300_wm97xx_ops = {
+	.irq_gpio	= WM97XX_GPIO_3,
+};
+
+static int db1300_wm97xx_probe(struct platform_device *pdev)
+{
+	struct wm97xx *wm = platform_get_drvdata(pdev);
+
+	/* external pendown indicator */
+	wm97xx_config_gpio(wm, WM97XX_GPIO_13, WM97XX_GPIO_IN,
+			   WM97XX_GPIO_POL_LOW, WM97XX_GPIO_STICKY,
+			   WM97XX_GPIO_WAKE);
+
+	/* internal "virtual" pendown gpio */
+	wm97xx_config_gpio(wm, WM97XX_GPIO_3, WM97XX_GPIO_OUT,
+			   WM97XX_GPIO_POL_LOW, WM97XX_GPIO_NOTSTICKY,
+			   WM97XX_GPIO_NOWAKE);
+
+	wm->pen_irq = DB1300_AC97_PEN_INT;
+
+	return wm97xx_register_mach_ops(wm, &db1300_wm97xx_ops);
+}
+#else
+static int db1300_wm97xx_probe(struct platform_device *pdev)
+{
+	return -ENODEV;
+}
+#endif
+
+static struct platform_driver db1300_wm97xx_driver = {
+	.driver.name	= "wm97xx-touch",
+	.driver.owner	= THIS_MODULE,
+	.probe		= db1300_wm97xx_probe,
+};
+
+/**********************************************************************/
+
+static struct platform_device *db1300_dev[] __initdata = {
+	&db1300_eth_dev,
+	&db1300_i2c_dev,
+	&db1300_5waysw_dev,
+	&db1300_nand_dev,
+	&db1300_ide_dev,
+#ifdef CONFIG_MMC_AU1X
+	&db1300_sd0_dev,
+	&db1300_sd1_dev,
+#endif
+	&db1300_lcd_dev,
+	&db1300_ac97_dev,
+	&db1300_i2s_dev,
+	&db1300_wm9715_dev,
+	&db1300_ac97dma_dev,
+	&db1300_i2sdma_dev,
+	&db1300_sndac97_dev,
+	&db1300_sndi2s_dev,
+};
+
+int __init db1300_dev_setup(void)
+{
+	int swapped, cpldirq;
+	struct clk *c;
+
+	/* setup CPLD IRQ muxer */
+	cpldirq = au1300_gpio_to_irq(AU1300_PIN_EXTCLK1);
+	irq_set_irq_type(cpldirq, IRQ_TYPE_LEVEL_HIGH);
+	bcsr_init_irq(DB1300_FIRST_INT, DB1300_LAST_INT, cpldirq);
+
+	/* insert/eject IRQs: one always triggers so don't enable them
+	 * when doing request_irq() on them.  DB1200 has this bug too.
+	 */
+	irq_set_status_flags(DB1300_SD1_INSERT_INT, IRQ_NOAUTOEN);
+	irq_set_status_flags(DB1300_SD1_EJECT_INT, IRQ_NOAUTOEN);
+	irq_set_status_flags(DB1300_CF_INSERT_INT, IRQ_NOAUTOEN);
+	irq_set_status_flags(DB1300_CF_EJECT_INT, IRQ_NOAUTOEN);
+
+	/*
+	 * setup board
+	 */
+	prom_get_ethernet_addr(&db1300_eth_config.mac[0]);
+
+	i2c_register_board_info(0, db1300_i2c_devs,
+				ARRAY_SIZE(db1300_i2c_devs));
+
+	if (platform_driver_register(&db1300_wm97xx_driver))
+		pr_warn("DB1300: failed to init touch pen irq support!\n");
+
+	/* Audio PSC clock is supplied by codecs (PSC1, 2) */
+	__raw_writel(PSC_SEL_CLK_SERCLK,
+	    (void __iomem *)KSEG1ADDR(AU1300_PSC1_PHYS_ADDR) + PSC_SEL_OFFSET);
+	wmb();
+	__raw_writel(PSC_SEL_CLK_SERCLK,
+	    (void __iomem *)KSEG1ADDR(AU1300_PSC2_PHYS_ADDR) + PSC_SEL_OFFSET);
+	wmb();
+	/* I2C driver wants 50MHz, get as close as possible */
+	c = clk_get(NULL, "psc3_intclk");
+	if (!IS_ERR(c)) {
+		clk_set_rate(c, 50000000);
+		clk_prepare_enable(c);
+		clk_put(c);
+	}
+	__raw_writel(PSC_SEL_CLK_INTCLK,
+	    (void __iomem *)KSEG1ADDR(AU1300_PSC3_PHYS_ADDR) + PSC_SEL_OFFSET);
+	wmb();
+
+	/* enable power to USB ports */
+	bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_USBHPWR | BCSR_RESETS_OTGPWR);
+
+	/* although it is socket #0, it uses the CPLD bits which previous boards
+	 * have used for socket #1.
+	 */
+	db1x_register_pcmcia_socket(
+		AU1000_PCMCIA_ATTR_PHYS_ADDR,
+		AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x00400000 - 1,
+		AU1000_PCMCIA_MEM_PHYS_ADDR,
+		AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x00400000 - 1,
+		AU1000_PCMCIA_IO_PHYS_ADDR,
+		AU1000_PCMCIA_IO_PHYS_ADDR   + 0x00010000 - 1,
+		DB1300_CF_INT, DB1300_CF_INSERT_INT, 0, DB1300_CF_EJECT_INT, 1);
+
+	swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1200_SWAPBOOT;
+	db1x_register_norflash(64 << 20, 2, swapped);
+
+	return platform_add_devices(db1300_dev, ARRAY_SIZE(db1300_dev));
+}
+
+
+int __init db1300_board_setup(void)
+{
+	unsigned short whoami;
+
+	bcsr_init(DB1300_BCSR_PHYS_ADDR,
+		  DB1300_BCSR_PHYS_ADDR + DB1300_BCSR_HEXLED_OFS);
+
+	whoami = bcsr_read(BCSR_WHOAMI);
+	if (BCSR_WHOAMI_BOARD(whoami) != BCSR_WHOAMI_DB1300)
+		return -ENODEV;
+
+	db1300_gpio_config();
+
+	printk(KERN_INFO "NetLogic DBAu1300 Development Platform.\n\t"
+		"BoardID %d   CPLD Rev %d   DaughtercardID %d\n",
+		BCSR_WHOAMI_BOARD(whoami), BCSR_WHOAMI_CPLD(whoami),
+		BCSR_WHOAMI_DCID(whoami));
+
+	/* enable UARTs, YAMON only enables #2 */
+	alchemy_uart_enable(AU1300_UART0_PHYS_ADDR);
+	alchemy_uart_enable(AU1300_UART1_PHYS_ADDR);
+	alchemy_uart_enable(AU1300_UART3_PHYS_ADDR);
+
+	return 0;
+}
diff --git a/arch/mips/alchemy/devboards/db1550.c b/arch/mips/alchemy/devboards/db1550.c
new file mode 100644
index 000000000..6c6837181
--- /dev/null
+++ b/arch/mips/alchemy/devboards/db1550.c
@@ -0,0 +1,629 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Alchemy Db1550/Pb1550 board support
+ *
+ * (c) 2011 Manuel Lauss <manuel.lauss@googlemail.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/interrupt.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/platnand.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#include <asm/bootinfo.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/gpio-au1000.h>
+#include <asm/mach-au1x00/au1xxx_eth.h>
+#include <asm/mach-au1x00/au1xxx_dbdma.h>
+#include <asm/mach-au1x00/au1xxx_psc.h>
+#include <asm/mach-au1x00/au1550_spi.h>
+#include <asm/mach-au1x00/au1550nd.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <prom.h>
+#include "platform.h"
+
+static void __init db1550_hw_setup(void)
+{
+	void __iomem *base;
+	unsigned long v;
+
+	/* complete pin setup: assign GPIO16 to PSC0_SYNC1 (SPI cs# line)
+	 * as well as PSC1_SYNC for AC97 on PB1550.
+	 */
+	v = alchemy_rdsys(AU1000_SYS_PINFUNC);
+	alchemy_wrsys(v | 1 | SYS_PF_PSC1_S1, AU1000_SYS_PINFUNC);
+
+	/* reset the AC97 codec now, the reset time in the psc-ac97 driver
+	 * is apparently too short although it's ridiculous as it is.
+	 */
+	base = (void __iomem *)KSEG1ADDR(AU1550_PSC1_PHYS_ADDR);
+	__raw_writel(PSC_SEL_CLK_SERCLK | PSC_SEL_PS_AC97MODE,
+		     base + PSC_SEL_OFFSET);
+	__raw_writel(PSC_CTRL_DISABLE, base + PSC_CTRL_OFFSET);
+	wmb();
+	__raw_writel(PSC_AC97RST_RST, base + PSC_AC97RST_OFFSET);
+	wmb();
+}
+
+int __init db1550_board_setup(void)
+{
+	unsigned short whoami;
+
+	bcsr_init(DB1550_BCSR_PHYS_ADDR,
+		  DB1550_BCSR_PHYS_ADDR + DB1550_BCSR_HEXLED_OFS);
+
+	whoami = bcsr_read(BCSR_WHOAMI); /* PB1550 hexled offset differs */
+	switch (BCSR_WHOAMI_BOARD(whoami)) {
+	case BCSR_WHOAMI_PB1550_SDR:
+	case BCSR_WHOAMI_PB1550_DDR:
+		bcsr_init(PB1550_BCSR_PHYS_ADDR,
+			  PB1550_BCSR_PHYS_ADDR + PB1550_BCSR_HEXLED_OFS);
+		break;
+	case BCSR_WHOAMI_DB1550:
+		break;
+	default:
+		return -ENODEV;
+	}
+
+	pr_info("Alchemy/AMD %s Board, CPLD Rev %d Board-ID %d	"	\
+		"Daughtercard ID %d\n", get_system_type(),
+		(whoami >> 4) & 0xf, (whoami >> 8) & 0xf, whoami & 0xf);
+
+	db1550_hw_setup();
+	return 0;
+}
+
+/*****************************************************************************/
+
+static u64 au1550_all_dmamask = DMA_BIT_MASK(32);
+
+static struct mtd_partition db1550_spiflash_parts[] = {
+	{
+		.name	= "spi_flash",
+		.offset = 0,
+		.size	= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct flash_platform_data db1550_spiflash_data = {
+	.name		= "s25fl010",
+	.parts		= db1550_spiflash_parts,
+	.nr_parts	= ARRAY_SIZE(db1550_spiflash_parts),
+	.type		= "m25p10",
+};
+
+static struct spi_board_info db1550_spi_devs[] __initdata = {
+	{
+		/* TI TMP121AIDBVR temp sensor */
+		.modalias	= "tmp121",
+		.max_speed_hz	= 2400000,
+		.bus_num	= 0,
+		.chip_select	= 0,
+		.mode		= SPI_MODE_0,
+	},
+	{
+		/* Spansion S25FL001D0FMA SPI flash */
+		.modalias	= "m25p80",
+		.max_speed_hz	= 2400000,
+		.bus_num	= 0,
+		.chip_select	= 1,
+		.mode		= SPI_MODE_0,
+		.platform_data	= &db1550_spiflash_data,
+	},
+};
+
+static struct i2c_board_info db1550_i2c_devs[] __initdata = {
+	{ I2C_BOARD_INFO("24c04",  0x52),}, /* AT24C04-10 I2C eeprom */
+	{ I2C_BOARD_INFO("ne1619", 0x2d),}, /* adm1025-compat hwmon */
+	{ I2C_BOARD_INFO("wm8731", 0x1b),}, /* I2S audio codec WM8731 */
+};
+
+/**********************************************************************/
+
+static void au1550_nand_cmd_ctrl(struct nand_chip *this, int cmd,
+				 unsigned int ctrl)
+{
+	unsigned long ioaddr = (unsigned long)this->legacy.IO_ADDR_W;
+
+	ioaddr &= 0xffffff00;
+
+	if (ctrl & NAND_CLE) {
+		ioaddr += MEM_STNAND_CMD;
+	} else if (ctrl & NAND_ALE) {
+		ioaddr += MEM_STNAND_ADDR;
+	} else {
+		/* assume we want to r/w real data  by default */
+		ioaddr += MEM_STNAND_DATA;
+	}
+	this->legacy.IO_ADDR_R = this->legacy.IO_ADDR_W = (void __iomem *)ioaddr;
+	if (cmd != NAND_CMD_NONE) {
+		__raw_writeb(cmd, this->legacy.IO_ADDR_W);
+		wmb();
+	}
+}
+
+static int au1550_nand_device_ready(struct nand_chip *this)
+{
+	return alchemy_rdsmem(AU1000_MEM_STSTAT) & 1;
+}
+
+static struct mtd_partition db1550_nand_parts[] = {
+	{
+		.name	= "NAND FS 0",
+		.offset = 0,
+		.size	= 8 * 1024 * 1024,
+	},
+	{
+		.name	= "NAND FS 1",
+		.offset = MTDPART_OFS_APPEND,
+		.size	= MTDPART_SIZ_FULL
+	},
+};
+
+struct platform_nand_data db1550_nand_platdata = {
+	.chip = {
+		.nr_chips	= 1,
+		.chip_offset	= 0,
+		.nr_partitions	= ARRAY_SIZE(db1550_nand_parts),
+		.partitions	= db1550_nand_parts,
+		.chip_delay	= 20,
+	},
+	.ctrl = {
+		.dev_ready	= au1550_nand_device_ready,
+		.cmd_ctrl	= au1550_nand_cmd_ctrl,
+	},
+};
+
+static struct resource db1550_nand_res[] = {
+	[0] = {
+		.start	= 0x20000000,
+		.end	= 0x200000ff,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device db1550_nand_dev = {
+	.name		= "gen_nand",
+	.num_resources	= ARRAY_SIZE(db1550_nand_res),
+	.resource	= db1550_nand_res,
+	.id		= -1,
+	.dev		= {
+		.platform_data = &db1550_nand_platdata,
+	}
+};
+
+static struct au1550nd_platdata pb1550_nand_pd = {
+	.parts		= db1550_nand_parts,
+	.num_parts	= ARRAY_SIZE(db1550_nand_parts),
+	.devwidth	= 0,	/* x8 NAND default, needs fixing up */
+};
+
+static struct platform_device pb1550_nand_dev = {
+	.name		= "au1550-nand",
+	.id		= -1,
+	.resource	= db1550_nand_res,
+	.num_resources	= ARRAY_SIZE(db1550_nand_res),
+	.dev		= {
+		.platform_data	= &pb1550_nand_pd,
+	},
+};
+
+static void __init pb1550_nand_setup(void)
+{
+	int boot_swapboot = (alchemy_rdsmem(AU1000_MEM_STSTAT) & (0x7 << 1)) |
+			    ((bcsr_read(BCSR_STATUS) >> 6) & 0x1);
+
+	gpio_direction_input(206);	/* de-assert NAND CS# */
+	switch (boot_swapboot) {
+	case 0: case 2: case 8: case 0xC: case 0xD:
+		/* x16 NAND Flash */
+		pb1550_nand_pd.devwidth = 1;
+		fallthrough;
+	case 1: case 3: case 9: case 0xE: case 0xF:
+		/* x8 NAND, already set up */
+		platform_device_register(&pb1550_nand_dev);
+	}
+}
+
+/**********************************************************************/
+
+static struct resource au1550_psc0_res[] = {
+	[0] = {
+		.start	= AU1550_PSC0_PHYS_ADDR,
+		.end	= AU1550_PSC0_PHYS_ADDR + 0xfff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AU1550_PSC0_INT,
+		.end	= AU1550_PSC0_INT,
+		.flags	= IORESOURCE_IRQ,
+	},
+	[2] = {
+		.start	= AU1550_DSCR_CMD0_PSC0_TX,
+		.end	= AU1550_DSCR_CMD0_PSC0_TX,
+		.flags	= IORESOURCE_DMA,
+	},
+	[3] = {
+		.start	= AU1550_DSCR_CMD0_PSC0_RX,
+		.end	= AU1550_DSCR_CMD0_PSC0_RX,
+		.flags	= IORESOURCE_DMA,
+	},
+};
+
+static void db1550_spi_cs_en(struct au1550_spi_info *spi, int cs, int pol)
+{
+	if (cs)
+		bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SPISEL);
+	else
+		bcsr_mod(BCSR_BOARD, BCSR_BOARD_SPISEL, 0);
+}
+
+static struct au1550_spi_info db1550_spi_platdata = {
+	.mainclk_hz	= 48000000,	/* PSC0 clock: max. 2.4MHz SPI clk */
+	.num_chipselect = 2,
+	.activate_cs	= db1550_spi_cs_en,
+};
+
+
+static struct platform_device db1550_spi_dev = {
+	.dev	= {
+		.dma_mask		= &au1550_all_dmamask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+		.platform_data		= &db1550_spi_platdata,
+	},
+	.name		= "au1550-spi",
+	.id		= 0,	/* bus number */
+	.num_resources	= ARRAY_SIZE(au1550_psc0_res),
+	.resource	= au1550_psc0_res,
+};
+
+/**********************************************************************/
+
+static struct resource au1550_psc1_res[] = {
+	[0] = {
+		.start	= AU1550_PSC1_PHYS_ADDR,
+		.end	= AU1550_PSC1_PHYS_ADDR + 0xfff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AU1550_PSC1_INT,
+		.end	= AU1550_PSC1_INT,
+		.flags	= IORESOURCE_IRQ,
+	},
+	[2] = {
+		.start	= AU1550_DSCR_CMD0_PSC1_TX,
+		.end	= AU1550_DSCR_CMD0_PSC1_TX,
+		.flags	= IORESOURCE_DMA,
+	},
+	[3] = {
+		.start	= AU1550_DSCR_CMD0_PSC1_RX,
+		.end	= AU1550_DSCR_CMD0_PSC1_RX,
+		.flags	= IORESOURCE_DMA,
+	},
+};
+
+static struct platform_device db1550_ac97_dev = {
+	.name		= "au1xpsc_ac97",
+	.id		= 1,	/* PSC ID */
+	.num_resources	= ARRAY_SIZE(au1550_psc1_res),
+	.resource	= au1550_psc1_res,
+};
+
+
+static struct resource au1550_psc2_res[] = {
+	[0] = {
+		.start	= AU1550_PSC2_PHYS_ADDR,
+		.end	= AU1550_PSC2_PHYS_ADDR + 0xfff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AU1550_PSC2_INT,
+		.end	= AU1550_PSC2_INT,
+		.flags	= IORESOURCE_IRQ,
+	},
+	[2] = {
+		.start	= AU1550_DSCR_CMD0_PSC2_TX,
+		.end	= AU1550_DSCR_CMD0_PSC2_TX,
+		.flags	= IORESOURCE_DMA,
+	},
+	[3] = {
+		.start	= AU1550_DSCR_CMD0_PSC2_RX,
+		.end	= AU1550_DSCR_CMD0_PSC2_RX,
+		.flags	= IORESOURCE_DMA,
+	},
+};
+
+static struct platform_device db1550_i2c_dev = {
+	.name		= "au1xpsc_smbus",
+	.id		= 0,	/* bus number */
+	.num_resources	= ARRAY_SIZE(au1550_psc2_res),
+	.resource	= au1550_psc2_res,
+};
+
+/**********************************************************************/
+
+static struct resource au1550_psc3_res[] = {
+	[0] = {
+		.start	= AU1550_PSC3_PHYS_ADDR,
+		.end	= AU1550_PSC3_PHYS_ADDR + 0xfff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AU1550_PSC3_INT,
+		.end	= AU1550_PSC3_INT,
+		.flags	= IORESOURCE_IRQ,
+	},
+	[2] = {
+		.start	= AU1550_DSCR_CMD0_PSC3_TX,
+		.end	= AU1550_DSCR_CMD0_PSC3_TX,
+		.flags	= IORESOURCE_DMA,
+	},
+	[3] = {
+		.start	= AU1550_DSCR_CMD0_PSC3_RX,
+		.end	= AU1550_DSCR_CMD0_PSC3_RX,
+		.flags	= IORESOURCE_DMA,
+	},
+};
+
+static struct platform_device db1550_i2s_dev = {
+	.name		= "au1xpsc_i2s",
+	.id		= 3,	/* PSC ID */
+	.num_resources	= ARRAY_SIZE(au1550_psc3_res),
+	.resource	= au1550_psc3_res,
+};
+
+/**********************************************************************/
+
+static struct platform_device db1550_stac_dev = {
+	.name		= "ac97-codec",
+	.id		= 1,	/* on PSC1 */
+};
+
+static struct platform_device db1550_ac97dma_dev = {
+	.name		= "au1xpsc-pcm",
+	.id		= 1,	/* on PSC3 */
+};
+
+static struct platform_device db1550_i2sdma_dev = {
+	.name		= "au1xpsc-pcm",
+	.id		= 3,	/* on PSC3 */
+};
+
+static struct platform_device db1550_sndac97_dev = {
+	.name		= "db1550-ac97",
+	.dev = {
+		.dma_mask		= &au1550_all_dmamask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+};
+
+static struct platform_device db1550_sndi2s_dev = {
+	.name		= "db1550-i2s",
+	.dev = {
+		.dma_mask		= &au1550_all_dmamask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+};
+
+/**********************************************************************/
+
+static int db1550_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
+{
+	if ((slot < 11) || (slot > 13) || pin == 0)
+		return -1;
+	if (slot == 11)
+		return (pin == 1) ? AU1550_PCI_INTC : 0xff;
+	if (slot == 12) {
+		switch (pin) {
+		case 1: return AU1550_PCI_INTB;
+		case 2: return AU1550_PCI_INTC;
+		case 3: return AU1550_PCI_INTD;
+		case 4: return AU1550_PCI_INTA;
+		}
+	}
+	if (slot == 13) {
+		switch (pin) {
+		case 1: return AU1550_PCI_INTA;
+		case 2: return AU1550_PCI_INTB;
+		case 3: return AU1550_PCI_INTC;
+		case 4: return AU1550_PCI_INTD;
+		}
+	}
+	return -1;
+}
+
+static int pb1550_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
+{
+	if ((slot < 12) || (slot > 13) || pin == 0)
+		return -1;
+	if (slot == 12) {
+		switch (pin) {
+		case 1: return AU1500_PCI_INTB;
+		case 2: return AU1500_PCI_INTC;
+		case 3: return AU1500_PCI_INTD;
+		case 4: return AU1500_PCI_INTA;
+		}
+	}
+	if (slot == 13) {
+		switch (pin) {
+		case 1: return AU1500_PCI_INTA;
+		case 2: return AU1500_PCI_INTB;
+		case 3: return AU1500_PCI_INTC;
+		case 4: return AU1500_PCI_INTD;
+		}
+	}
+	return -1;
+}
+
+static struct resource alchemy_pci_host_res[] = {
+	[0] = {
+		.start	= AU1500_PCI_PHYS_ADDR,
+		.end	= AU1500_PCI_PHYS_ADDR + 0xfff,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+static struct alchemy_pci_platdata db1550_pci_pd = {
+	.board_map_irq	= db1550_map_pci_irq,
+};
+
+static struct platform_device db1550_pci_host_dev = {
+	.dev.platform_data = &db1550_pci_pd,
+	.name		= "alchemy-pci",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(alchemy_pci_host_res),
+	.resource	= alchemy_pci_host_res,
+};
+
+/**********************************************************************/
+
+static struct platform_device *db1550_devs[] __initdata = {
+	&db1550_i2c_dev,
+	&db1550_ac97_dev,
+	&db1550_spi_dev,
+	&db1550_i2s_dev,
+	&db1550_stac_dev,
+	&db1550_ac97dma_dev,
+	&db1550_i2sdma_dev,
+	&db1550_sndac97_dev,
+	&db1550_sndi2s_dev,
+};
+
+/* must be arch_initcall; MIPS PCI scans busses in a subsys_initcall */
+int __init db1550_pci_setup(int id)
+{
+	if (id)
+		db1550_pci_pd.board_map_irq = pb1550_map_pci_irq;
+	return platform_device_register(&db1550_pci_host_dev);
+}
+
+static void __init db1550_devices(void)
+{
+	alchemy_gpio_direction_output(203, 0);	/* red led on */
+
+	irq_set_irq_type(AU1550_GPIO0_INT, IRQ_TYPE_EDGE_BOTH);	 /* CD0# */
+	irq_set_irq_type(AU1550_GPIO1_INT, IRQ_TYPE_EDGE_BOTH);	 /* CD1# */
+	irq_set_irq_type(AU1550_GPIO3_INT, IRQ_TYPE_LEVEL_LOW);	 /* CARD0# */
+	irq_set_irq_type(AU1550_GPIO5_INT, IRQ_TYPE_LEVEL_LOW);	 /* CARD1# */
+	irq_set_irq_type(AU1550_GPIO21_INT, IRQ_TYPE_LEVEL_LOW); /* STSCHG0# */
+	irq_set_irq_type(AU1550_GPIO22_INT, IRQ_TYPE_LEVEL_LOW); /* STSCHG1# */
+
+	db1x_register_pcmcia_socket(
+		AU1000_PCMCIA_ATTR_PHYS_ADDR,
+		AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+		AU1000_PCMCIA_MEM_PHYS_ADDR,
+		AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x000400000 - 1,
+		AU1000_PCMCIA_IO_PHYS_ADDR,
+		AU1000_PCMCIA_IO_PHYS_ADDR   + 0x000010000 - 1,
+		AU1550_GPIO3_INT, 0,
+		/*AU1550_GPIO21_INT*/0, 0, 0);
+
+	db1x_register_pcmcia_socket(
+		AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
+		AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
+		AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x004000000,
+		AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x004400000 - 1,
+		AU1000_PCMCIA_IO_PHYS_ADDR   + 0x004000000,
+		AU1000_PCMCIA_IO_PHYS_ADDR   + 0x004010000 - 1,
+		AU1550_GPIO5_INT, 1,
+		/*AU1550_GPIO22_INT*/0, 0, 1);
+
+	platform_device_register(&db1550_nand_dev);
+
+	alchemy_gpio_direction_output(202, 0);	/* green led on */
+}
+
+static void __init pb1550_devices(void)
+{
+	irq_set_irq_type(AU1550_GPIO0_INT, IRQ_TYPE_LEVEL_LOW);
+	irq_set_irq_type(AU1550_GPIO1_INT, IRQ_TYPE_LEVEL_LOW);
+	irq_set_irq_type(AU1550_GPIO201_205_INT, IRQ_TYPE_LEVEL_HIGH);
+
+	/* enable both PCMCIA card irqs in the shared line */
+	alchemy_gpio2_enable_int(201);	/* socket 0 card irq */
+	alchemy_gpio2_enable_int(202);	/* socket 1 card irq */
+
+	/* Pb1550, like all others, also has statuschange irqs; however they're
+	* wired up on one of the Au1550's shared GPIO201_205 line, which also
+	* services the PCMCIA card interrupts.	So we ignore statuschange and
+	* use the GPIO201_205 exclusively for card interrupts, since a) pcmcia
+	* drivers are used to shared irqs and b) statuschange isn't really use-
+	* ful anyway.
+	*/
+	db1x_register_pcmcia_socket(
+		AU1000_PCMCIA_ATTR_PHYS_ADDR,
+		AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+		AU1000_PCMCIA_MEM_PHYS_ADDR,
+		AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x000400000 - 1,
+		AU1000_PCMCIA_IO_PHYS_ADDR,
+		AU1000_PCMCIA_IO_PHYS_ADDR   + 0x000010000 - 1,
+		AU1550_GPIO201_205_INT, AU1550_GPIO0_INT, 0, 0, 0);
+
+	db1x_register_pcmcia_socket(
+		AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008000000,
+		AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008400000 - 1,
+		AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x008000000,
+		AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x008400000 - 1,
+		AU1000_PCMCIA_IO_PHYS_ADDR   + 0x008000000,
+		AU1000_PCMCIA_IO_PHYS_ADDR   + 0x008010000 - 1,
+		AU1550_GPIO201_205_INT, AU1550_GPIO1_INT, 0, 0, 1);
+
+	pb1550_nand_setup();
+}
+
+int __init db1550_dev_setup(void)
+{
+	int swapped, id;
+	struct clk *c;
+
+	id = (BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI)) != BCSR_WHOAMI_DB1550);
+
+	i2c_register_board_info(0, db1550_i2c_devs,
+				ARRAY_SIZE(db1550_i2c_devs));
+	spi_register_board_info(db1550_spi_devs,
+				ARRAY_SIZE(db1550_spi_devs));
+
+	c = clk_get(NULL, "psc0_intclk");
+	if (!IS_ERR(c)) {
+		clk_set_rate(c, 50000000);
+		clk_prepare_enable(c);
+		clk_put(c);
+	}
+	c = clk_get(NULL, "psc2_intclk");
+	if (!IS_ERR(c)) {
+		clk_set_rate(c, db1550_spi_platdata.mainclk_hz);
+		clk_prepare_enable(c);
+		clk_put(c);
+	}
+
+	/* Audio PSC clock is supplied by codecs (PSC1, 3) FIXME: platdata!! */
+	__raw_writel(PSC_SEL_CLK_SERCLK,
+	    (void __iomem *)KSEG1ADDR(AU1550_PSC1_PHYS_ADDR) + PSC_SEL_OFFSET);
+	wmb();
+	__raw_writel(PSC_SEL_CLK_SERCLK,
+	    (void __iomem *)KSEG1ADDR(AU1550_PSC3_PHYS_ADDR) + PSC_SEL_OFFSET);
+	wmb();
+	/* SPI/I2C use internally supplied 50MHz source */
+	__raw_writel(PSC_SEL_CLK_INTCLK,
+	    (void __iomem *)KSEG1ADDR(AU1550_PSC0_PHYS_ADDR) + PSC_SEL_OFFSET);
+	wmb();
+	__raw_writel(PSC_SEL_CLK_INTCLK,
+	    (void __iomem *)KSEG1ADDR(AU1550_PSC2_PHYS_ADDR) + PSC_SEL_OFFSET);
+	wmb();
+
+	id ? pb1550_devices() : db1550_devices();
+
+	swapped = bcsr_read(BCSR_STATUS) &
+	       (id ? BCSR_STATUS_PB1550_SWAPBOOT : BCSR_STATUS_DB1000_SWAPBOOT);
+	db1x_register_norflash(128 << 20, 4, swapped);
+
+	return platform_add_devices(db1550_devs, ARRAY_SIZE(db1550_devs));
+}
diff --git a/arch/mips/alchemy/devboards/db1xxx.c b/arch/mips/alchemy/devboards/db1xxx.c
new file mode 100644
index 000000000..e6d25aad8
--- /dev/null
+++ b/arch/mips/alchemy/devboards/db1xxx.c
@@ -0,0 +1,124 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Alchemy DB/PB1xxx board support.
+ */
+
+#include <asm/prom.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-db1x00/bcsr.h>
+
+int __init db1000_board_setup(void);
+int __init db1000_dev_setup(void);
+int __init db1500_pci_setup(void);
+int __init db1200_board_setup(void);
+int __init db1200_dev_setup(void);
+int __init db1300_board_setup(void);
+int __init db1300_dev_setup(void);
+int __init db1550_board_setup(void);
+int __init db1550_dev_setup(void);
+int __init db1550_pci_setup(int);
+
+static const char *board_type_str(void)
+{
+	switch (BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI))) {
+	case BCSR_WHOAMI_DB1000:
+		return "DB1000";
+	case BCSR_WHOAMI_DB1500:
+		return "DB1500";
+	case BCSR_WHOAMI_DB1100:
+		return "DB1100";
+	case BCSR_WHOAMI_PB1500:
+	case BCSR_WHOAMI_PB1500R2:
+		return "PB1500";
+	case BCSR_WHOAMI_PB1100:
+		return "PB1100";
+	case BCSR_WHOAMI_PB1200_DDR1:
+	case BCSR_WHOAMI_PB1200_DDR2:
+		return "PB1200";
+	case BCSR_WHOAMI_DB1200:
+		return "DB1200";
+	case BCSR_WHOAMI_DB1300:
+		return "DB1300";
+	case BCSR_WHOAMI_DB1550:
+		return "DB1550";
+	case BCSR_WHOAMI_PB1550_SDR:
+	case BCSR_WHOAMI_PB1550_DDR:
+		return "PB1550";
+	default:
+		return "(unknown)";
+	}
+}
+
+const char *get_system_type(void)
+{
+	return board_type_str();
+}
+
+void __init board_setup(void)
+{
+	int ret;
+
+	switch (alchemy_get_cputype()) {
+	case ALCHEMY_CPU_AU1000:
+	case ALCHEMY_CPU_AU1500:
+	case ALCHEMY_CPU_AU1100:
+		ret = db1000_board_setup();
+		break;
+	case ALCHEMY_CPU_AU1550:
+		ret = db1550_board_setup();
+		break;
+	case ALCHEMY_CPU_AU1200:
+		ret = db1200_board_setup();
+		break;
+	case ALCHEMY_CPU_AU1300:
+		ret = db1300_board_setup();
+		break;
+	default:
+		pr_err("unsupported CPU on board\n");
+		ret = -ENODEV;
+	}
+	if (ret)
+		panic("cannot initialize board support");
+}
+
+static int __init db1xxx_arch_init(void)
+{
+	int id = BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI));
+	if (id == BCSR_WHOAMI_DB1550)
+		return db1550_pci_setup(0);
+	else if ((id == BCSR_WHOAMI_PB1550_SDR) ||
+		 (id == BCSR_WHOAMI_PB1550_DDR))
+		return db1550_pci_setup(1);
+	else if ((id == BCSR_WHOAMI_DB1500) || (id == BCSR_WHOAMI_PB1500) ||
+		 (id == BCSR_WHOAMI_PB1500R2))
+		return db1500_pci_setup();
+
+	return 0;
+}
+arch_initcall(db1xxx_arch_init);
+
+static int __init db1xxx_dev_init(void)
+{
+	mips_set_machine_name(board_type_str());
+	switch (BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI))) {
+	case BCSR_WHOAMI_DB1000:
+	case BCSR_WHOAMI_DB1500:
+	case BCSR_WHOAMI_DB1100:
+	case BCSR_WHOAMI_PB1500:
+	case BCSR_WHOAMI_PB1500R2:
+	case BCSR_WHOAMI_PB1100:
+		return db1000_dev_setup();
+	case BCSR_WHOAMI_PB1200_DDR1:
+	case BCSR_WHOAMI_PB1200_DDR2:
+	case BCSR_WHOAMI_DB1200:
+		return db1200_dev_setup();
+	case BCSR_WHOAMI_DB1300:
+		return db1300_dev_setup();
+	case BCSR_WHOAMI_DB1550:
+	case BCSR_WHOAMI_PB1550_SDR:
+	case BCSR_WHOAMI_PB1550_DDR:
+		return db1550_dev_setup();
+	}
+	return 0;
+}
+device_initcall(db1xxx_dev_init);
diff --git a/arch/mips/alchemy/devboards/platform.c b/arch/mips/alchemy/devboards/platform.c
new file mode 100644
index 000000000..754bdd2ca
--- /dev/null
+++ b/arch/mips/alchemy/devboards/platform.c
@@ -0,0 +1,248 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * devoard misc stuff.
+ */
+
+#include <linux/init.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/physmap.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+
+#include <asm/bootinfo.h>
+#include <asm/idle.h>
+#include <asm/reboot.h>
+#include <asm/setup.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-db1x00/bcsr.h>
+
+#include <prom.h>
+
+void prom_putchar(char c)
+{
+	if (alchemy_get_cputype() == ALCHEMY_CPU_AU1300)
+		alchemy_uart_putchar(AU1300_UART2_PHYS_ADDR, c);
+	else
+		alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
+}
+
+
+static struct platform_device db1x00_rtc_dev = {
+	.name	= "rtc-au1xxx",
+	.id	= -1,
+};
+
+
+static void db1x_power_off(void)
+{
+	bcsr_write(BCSR_RESETS, 0);
+	bcsr_write(BCSR_SYSTEM, BCSR_SYSTEM_PWROFF | BCSR_SYSTEM_RESET);
+	while (1)		/* sit and spin */
+		cpu_wait();
+}
+
+static void db1x_reset(char *c)
+{
+	bcsr_write(BCSR_RESETS, 0);
+	bcsr_write(BCSR_SYSTEM, 0);
+}
+
+static int __init db1x_late_setup(void)
+{
+	if (!pm_power_off)
+		pm_power_off = db1x_power_off;
+	if (!_machine_halt)
+		_machine_halt = db1x_power_off;
+	if (!_machine_restart)
+		_machine_restart = db1x_reset;
+
+	platform_device_register(&db1x00_rtc_dev);
+
+	return 0;
+}
+device_initcall(db1x_late_setup);
+
+/* register a pcmcia socket */
+int __init db1x_register_pcmcia_socket(phys_addr_t pcmcia_attr_start,
+				       phys_addr_t pcmcia_attr_end,
+				       phys_addr_t pcmcia_mem_start,
+				       phys_addr_t pcmcia_mem_end,
+				       phys_addr_t pcmcia_io_start,
+				       phys_addr_t pcmcia_io_end,
+				       int card_irq,
+				       int cd_irq,
+				       int stschg_irq,
+				       int eject_irq,
+				       int id)
+{
+	int cnt, i, ret;
+	struct resource *sr;
+	struct platform_device *pd;
+
+	cnt = 5;
+	if (eject_irq)
+		cnt++;
+	if (stschg_irq)
+		cnt++;
+
+	sr = kcalloc(cnt, sizeof(struct resource), GFP_KERNEL);
+	if (!sr)
+		return -ENOMEM;
+
+	pd = platform_device_alloc("db1xxx_pcmcia", id);
+	if (!pd) {
+		ret = -ENOMEM;
+		goto out;
+	}
+
+	sr[0].name	= "pcmcia-attr";
+	sr[0].flags	= IORESOURCE_MEM;
+	sr[0].start	= pcmcia_attr_start;
+	sr[0].end	= pcmcia_attr_end;
+
+	sr[1].name	= "pcmcia-mem";
+	sr[1].flags	= IORESOURCE_MEM;
+	sr[1].start	= pcmcia_mem_start;
+	sr[1].end	= pcmcia_mem_end;
+
+	sr[2].name	= "pcmcia-io";
+	sr[2].flags	= IORESOURCE_MEM;
+	sr[2].start	= pcmcia_io_start;
+	sr[2].end	= pcmcia_io_end;
+
+	sr[3].name	= "insert";
+	sr[3].flags	= IORESOURCE_IRQ;
+	sr[3].start = sr[3].end = cd_irq;
+
+	sr[4].name	= "card";
+	sr[4].flags	= IORESOURCE_IRQ;
+	sr[4].start = sr[4].end = card_irq;
+
+	i = 5;
+	if (stschg_irq) {
+		sr[i].name	= "stschg";
+		sr[i].flags	= IORESOURCE_IRQ;
+		sr[i].start = sr[i].end = stschg_irq;
+		i++;
+	}
+	if (eject_irq) {
+		sr[i].name	= "eject";
+		sr[i].flags	= IORESOURCE_IRQ;
+		sr[i].start = sr[i].end = eject_irq;
+	}
+
+	pd->resource = sr;
+	pd->num_resources = cnt;
+
+	ret = platform_device_add(pd);
+	if (!ret)
+		return 0;
+
+	platform_device_put(pd);
+out:
+	kfree(sr);
+	return ret;
+}
+
+#define YAMON_SIZE	0x00100000
+#define YAMON_ENV_SIZE	0x00040000
+
+int __init db1x_register_norflash(unsigned long size, int width,
+				  int swapped)
+{
+	struct physmap_flash_data *pfd;
+	struct platform_device *pd;
+	struct mtd_partition *parts;
+	struct resource *res;
+	int ret, i;
+
+	if (size < (8 * 1024 * 1024))
+		return -EINVAL;
+
+	ret = -ENOMEM;
+	parts = kcalloc(5, sizeof(struct mtd_partition), GFP_KERNEL);
+	if (!parts)
+		goto out;
+
+	res = kzalloc(sizeof(struct resource), GFP_KERNEL);
+	if (!res)
+		goto out1;
+
+	pfd = kzalloc(sizeof(struct physmap_flash_data), GFP_KERNEL);
+	if (!pfd)
+		goto out2;
+
+	pd = platform_device_alloc("physmap-flash", 0);
+	if (!pd)
+		goto out3;
+
+	/* NOR flash ends at 0x20000000, regardless of size */
+	res->start = 0x20000000 - size;
+	res->end = 0x20000000 - 1;
+	res->flags = IORESOURCE_MEM;
+
+	/* partition setup.  Most Develboards have a switch which allows
+	 * to swap the physical locations of the 2 NOR flash banks.
+	 */
+	i = 0;
+	if (!swapped) {
+		/* first NOR chip */
+		parts[i].offset = 0;
+		parts[i].name = "User FS";
+		parts[i].size = size / 2;
+		i++;
+	}
+
+	parts[i].offset = MTDPART_OFS_APPEND;
+	parts[i].name = "User FS 2";
+	parts[i].size = (size / 2) - (0x20000000 - 0x1fc00000);
+	i++;
+
+	parts[i].offset = MTDPART_OFS_APPEND;
+	parts[i].name = "YAMON";
+	parts[i].size = YAMON_SIZE;
+	parts[i].mask_flags = MTD_WRITEABLE;
+	i++;
+
+	parts[i].offset = MTDPART_OFS_APPEND;
+	parts[i].name = "raw kernel";
+	parts[i].size = 0x00400000 - YAMON_SIZE - YAMON_ENV_SIZE;
+	i++;
+
+	parts[i].offset = MTDPART_OFS_APPEND;
+	parts[i].name = "YAMON Env";
+	parts[i].size = YAMON_ENV_SIZE;
+	parts[i].mask_flags = MTD_WRITEABLE;
+	i++;
+
+	if (swapped) {
+		parts[i].offset = MTDPART_OFS_APPEND;
+		parts[i].name = "User FS";
+		parts[i].size = size / 2;
+		i++;
+	}
+
+	pfd->width = width;
+	pfd->parts = parts;
+	pfd->nr_parts = 5;
+
+	pd->dev.platform_data = pfd;
+	pd->resource = res;
+	pd->num_resources = 1;
+
+	ret = platform_device_add(pd);
+	if (!ret)
+		return ret;
+
+	platform_device_put(pd);
+out3:
+	kfree(pfd);
+out2:
+	kfree(res);
+out1:
+	kfree(parts);
+out:
+	return ret;
+}
diff --git a/arch/mips/alchemy/devboards/platform.h b/arch/mips/alchemy/devboards/platform.h
new file mode 100644
index 000000000..23d98fc09
--- /dev/null
+++ b/arch/mips/alchemy/devboards/platform.h
@@ -0,0 +1,22 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _DEVBOARD_PLATFORM_H_
+#define _DEVBOARD_PLATFORM_H_
+
+#include <linux/init.h>
+
+int __init db1x_register_pcmcia_socket(phys_addr_t pcmcia_attr_start,
+				       phys_addr_t pcmcia_attr_len,
+				       phys_addr_t pcmcia_mem_start,
+				       phys_addr_t pcmcia_mem_end,
+				       phys_addr_t pcmcia_io_start,
+				       phys_addr_t pcmcia_io_end,
+				       int card_irq,
+				       int cd_irq,
+				       int stschg_irq,
+				       int eject_irq,
+				       int id);
+
+int __init db1x_register_norflash(unsigned long size, int width,
+				  int swapped);
+
+#endif
diff --git a/arch/mips/alchemy/devboards/pm.c b/arch/mips/alchemy/devboards/pm.c
new file mode 100644
index 000000000..b17a0d199
--- /dev/null
+++ b/arch/mips/alchemy/devboards/pm.c
@@ -0,0 +1,254 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Alchemy Development Board example suspend userspace interface.
+ *
+ * (c) 2008 Manuel Lauss <mano@roarinelk.homelinux.net>
+ */
+
+#include <linux/init.h>
+#include <linux/kobject.h>
+#include <linux/suspend.h>
+#include <linux/sysfs.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/gpio-au1000.h>
+#include <asm/mach-db1x00/bcsr.h>
+
+/*
+ * Generic suspend userspace interface for Alchemy development boards.
+ * This code exports a few sysfs nodes under /sys/power/db1x/ which
+ * can be used by userspace to en/disable all au1x-provided wakeup
+ * sources and configure the timeout after which the TOYMATCH2 irq
+ * is to trigger a wakeup.
+ */
+
+
+static unsigned long db1x_pm_sleep_secs;
+static unsigned long db1x_pm_wakemsk;
+static unsigned long db1x_pm_last_wakesrc;
+
+static int db1x_pm_enter(suspend_state_t state)
+{
+	unsigned short bcsrs[16];
+	int i, j, hasint;
+
+	/* save CPLD regs */
+	hasint = bcsr_read(BCSR_WHOAMI);
+	hasint = BCSR_WHOAMI_BOARD(hasint) >= BCSR_WHOAMI_DB1200;
+	j = (hasint) ? BCSR_MASKSET : BCSR_SYSTEM;
+
+	for (i = BCSR_STATUS; i <= j; i++)
+		bcsrs[i] = bcsr_read(i);
+
+	/* shut off hexleds */
+	bcsr_write(BCSR_HEXCLEAR, 3);
+
+	/* enable GPIO based wakeup */
+	alchemy_gpio1_input_enable();
+
+	/* clear and setup wake cause and source */
+	alchemy_wrsys(0, AU1000_SYS_WAKEMSK);
+	alchemy_wrsys(0, AU1000_SYS_WAKESRC);
+
+	alchemy_wrsys(db1x_pm_wakemsk, AU1000_SYS_WAKEMSK);
+
+	/* setup 1Hz-timer-based wakeup: wait for reg access */
+	while (alchemy_rdsys(AU1000_SYS_CNTRCTRL) & SYS_CNTRL_M20)
+		asm volatile ("nop");
+
+	alchemy_wrsys(alchemy_rdsys(AU1000_SYS_TOYREAD) + db1x_pm_sleep_secs,
+		      AU1000_SYS_TOYMATCH2);
+
+	/* wait for value to really hit the register */
+	while (alchemy_rdsys(AU1000_SYS_CNTRCTRL) & SYS_CNTRL_M20)
+		asm volatile ("nop");
+
+	/* ...and now the sandman can come! */
+	au_sleep();
+
+
+	/* restore CPLD regs */
+	for (i = BCSR_STATUS; i <= BCSR_SYSTEM; i++)
+		bcsr_write(i, bcsrs[i]);
+
+	/* restore CPLD int registers */
+	if (hasint) {
+		bcsr_write(BCSR_INTCLR, 0xffff);
+		bcsr_write(BCSR_MASKCLR, 0xffff);
+		bcsr_write(BCSR_INTSTAT, 0xffff);
+		bcsr_write(BCSR_INTSET, bcsrs[BCSR_INTSET]);
+		bcsr_write(BCSR_MASKSET, bcsrs[BCSR_MASKSET]);
+	}
+
+	/* light up hexleds */
+	bcsr_write(BCSR_HEXCLEAR, 0);
+
+	return 0;
+}
+
+static int db1x_pm_begin(suspend_state_t state)
+{
+	if (!db1x_pm_wakemsk) {
+		printk(KERN_ERR "db1x: no wakeup source activated!\n");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static void db1x_pm_end(void)
+{
+	/* read and store wakeup source, the clear the register. To
+	 * be able to clear it, WAKEMSK must be cleared first.
+	 */
+	db1x_pm_last_wakesrc = alchemy_rdsys(AU1000_SYS_WAKESRC);
+
+	alchemy_wrsys(0, AU1000_SYS_WAKEMSK);
+	alchemy_wrsys(0, AU1000_SYS_WAKESRC);
+}
+
+static const struct platform_suspend_ops db1x_pm_ops = {
+	.valid		= suspend_valid_only_mem,
+	.begin		= db1x_pm_begin,
+	.enter		= db1x_pm_enter,
+	.end		= db1x_pm_end,
+};
+
+#define ATTRCMP(x) (0 == strcmp(attr->attr.name, #x))
+
+static ssize_t db1x_pmattr_show(struct kobject *kobj,
+				struct kobj_attribute *attr,
+				char *buf)
+{
+	int idx;
+
+	if (ATTRCMP(timer_timeout))
+		return sprintf(buf, "%lu\n", db1x_pm_sleep_secs);
+
+	else if (ATTRCMP(timer))
+		return sprintf(buf, "%u\n",
+				!!(db1x_pm_wakemsk & SYS_WAKEMSK_M2));
+
+	else if (ATTRCMP(wakesrc))
+		return sprintf(buf, "%lu\n", db1x_pm_last_wakesrc);
+
+	else if (ATTRCMP(gpio0) || ATTRCMP(gpio1) || ATTRCMP(gpio2) ||
+		 ATTRCMP(gpio3) || ATTRCMP(gpio4) || ATTRCMP(gpio5) ||
+		 ATTRCMP(gpio6) || ATTRCMP(gpio7)) {
+		idx = (attr->attr.name)[4] - '0';
+		return sprintf(buf, "%d\n",
+			!!(db1x_pm_wakemsk & SYS_WAKEMSK_GPIO(idx)));
+
+	} else if (ATTRCMP(wakemsk)) {
+		return sprintf(buf, "%08lx\n", db1x_pm_wakemsk);
+	}
+
+	return -ENOENT;
+}
+
+static ssize_t db1x_pmattr_store(struct kobject *kobj,
+				 struct kobj_attribute *attr,
+				 const char *instr,
+				 size_t bytes)
+{
+	unsigned long l;
+	int tmp;
+
+	if (ATTRCMP(timer_timeout)) {
+		tmp = kstrtoul(instr, 0, &l);
+		if (tmp)
+			return tmp;
+
+		db1x_pm_sleep_secs = l;
+
+	} else if (ATTRCMP(timer)) {
+		if (instr[0] != '0')
+			db1x_pm_wakemsk |= SYS_WAKEMSK_M2;
+		else
+			db1x_pm_wakemsk &= ~SYS_WAKEMSK_M2;
+
+	} else if (ATTRCMP(gpio0) || ATTRCMP(gpio1) || ATTRCMP(gpio2) ||
+		   ATTRCMP(gpio3) || ATTRCMP(gpio4) || ATTRCMP(gpio5) ||
+		   ATTRCMP(gpio6) || ATTRCMP(gpio7)) {
+		tmp = (attr->attr.name)[4] - '0';
+		if (instr[0] != '0') {
+			db1x_pm_wakemsk |= SYS_WAKEMSK_GPIO(tmp);
+		} else {
+			db1x_pm_wakemsk &= ~SYS_WAKEMSK_GPIO(tmp);
+		}
+
+	} else if (ATTRCMP(wakemsk)) {
+		tmp = kstrtoul(instr, 0, &l);
+		if (tmp)
+			return tmp;
+
+		db1x_pm_wakemsk = l & 0x0000003f;
+
+	} else
+		bytes = -ENOENT;
+
+	return bytes;
+}
+
+#define ATTR(x)							\
+	static struct kobj_attribute x##_attribute =		\
+		__ATTR(x, 0664, db1x_pmattr_show,		\
+				db1x_pmattr_store);
+
+ATTR(gpio0)		/* GPIO-based wakeup enable */
+ATTR(gpio1)
+ATTR(gpio2)
+ATTR(gpio3)
+ATTR(gpio4)
+ATTR(gpio5)
+ATTR(gpio6)
+ATTR(gpio7)
+ATTR(timer)		/* TOYMATCH2-based wakeup enable */
+ATTR(timer_timeout)	/* timer-based wakeup timeout value, in seconds */
+ATTR(wakesrc)		/* contents of SYS_WAKESRC after last wakeup */
+ATTR(wakemsk)		/* direct access to SYS_WAKEMSK */
+
+#define ATTR_LIST(x)	& x ## _attribute.attr
+static struct attribute *db1x_pmattrs[] = {
+	ATTR_LIST(gpio0),
+	ATTR_LIST(gpio1),
+	ATTR_LIST(gpio2),
+	ATTR_LIST(gpio3),
+	ATTR_LIST(gpio4),
+	ATTR_LIST(gpio5),
+	ATTR_LIST(gpio6),
+	ATTR_LIST(gpio7),
+	ATTR_LIST(timer),
+	ATTR_LIST(timer_timeout),
+	ATTR_LIST(wakesrc),
+	ATTR_LIST(wakemsk),
+	NULL,		/* terminator */
+};
+
+static struct attribute_group db1x_pmattr_group = {
+	.name	= "db1x",
+	.attrs	= db1x_pmattrs,
+};
+
+/*
+ * Initialize suspend interface
+ */
+static int __init pm_init(void)
+{
+	/* init TOY to tick at 1Hz if not already done. No need to wait
+	 * for confirmation since there's plenty of time from here to
+	 * the next suspend cycle.
+	 */
+	if (alchemy_rdsys(AU1000_SYS_TOYTRIM) != 32767)
+		alchemy_wrsys(32767, AU1000_SYS_TOYTRIM);
+
+	db1x_pm_last_wakesrc = alchemy_rdsys(AU1000_SYS_WAKESRC);
+
+	alchemy_wrsys(0, AU1000_SYS_WAKESRC);
+	alchemy_wrsys(0, AU1000_SYS_WAKEMSK);
+
+	suspend_set_ops(&db1x_pm_ops);
+
+	return sysfs_create_group(power_kobj, &db1x_pmattr_group);
+}
+
+late_initcall(pm_init);
diff --git a/arch/mips/ar7/Makefile b/arch/mips/ar7/Makefile
new file mode 100644
index 000000000..cd51c6c6e
--- /dev/null
+++ b/arch/mips/ar7/Makefile
@@ -0,0 +1,11 @@
+# SPDX-License-Identifier: GPL-2.0
+
+obj-y := \
+	prom.o \
+	setup.o \
+	memory.o \
+	irq.o \
+	time.o \
+	platform.o \
+	gpio.o \
+	clock.o
diff --git a/arch/mips/ar7/Platform b/arch/mips/ar7/Platform
new file mode 100644
index 000000000..a9257cc01
--- /dev/null
+++ b/arch/mips/ar7/Platform
@@ -0,0 +1,5 @@
+#
+# Texas Instruments AR7
+#
+cflags-$(CONFIG_AR7)		+= -I$(srctree)/arch/mips/include/asm/mach-ar7
+load-$(CONFIG_AR7)		+= 0xffffffff94100000
diff --git a/arch/mips/ar7/clock.c b/arch/mips/ar7/clock.c
new file mode 100644
index 000000000..c717acbc5
--- /dev/null
+++ b/arch/mips/ar7/clock.c
@@ -0,0 +1,439 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2007 Felix Fietkau <nbd@openwrt.org>
+ * Copyright (C) 2007 Eugene Konev <ejka@openwrt.org>
+ * Copyright (C) 2009 Florian Fainelli <florian@openwrt.org>
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/export.h>
+#include <linux/delay.h>
+#include <linux/gcd.h>
+#include <linux/io.h>
+#include <linux/err.h>
+#include <linux/clkdev.h>
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+
+#include <asm/addrspace.h>
+#include <asm/mach-ar7/ar7.h>
+
+#define BOOT_PLL_SOURCE_MASK	0x3
+#define CPU_PLL_SOURCE_SHIFT	16
+#define BUS_PLL_SOURCE_SHIFT	14
+#define USB_PLL_SOURCE_SHIFT	18
+#define DSP_PLL_SOURCE_SHIFT	22
+#define BOOT_PLL_SOURCE_AFE	0
+#define BOOT_PLL_SOURCE_BUS	0
+#define BOOT_PLL_SOURCE_REF	1
+#define BOOT_PLL_SOURCE_XTAL	2
+#define BOOT_PLL_SOURCE_CPU	3
+#define BOOT_PLL_BYPASS		0x00000020
+#define BOOT_PLL_ASYNC_MODE	0x02000000
+#define BOOT_PLL_2TO1_MODE	0x00008000
+
+#define TNETD7200_CLOCK_ID_CPU	0
+#define TNETD7200_CLOCK_ID_DSP	1
+#define TNETD7200_CLOCK_ID_USB	2
+
+#define TNETD7200_DEF_CPU_CLK	211000000
+#define TNETD7200_DEF_DSP_CLK	125000000
+#define TNETD7200_DEF_USB_CLK	48000000
+
+struct tnetd7300_clock {
+	u32 ctrl;
+#define PREDIV_MASK	0x001f0000
+#define PREDIV_SHIFT	16
+#define POSTDIV_MASK	0x0000001f
+	u32 unused1[3];
+	u32 pll;
+#define MUL_MASK	0x0000f000
+#define MUL_SHIFT	12
+#define PLL_MODE_MASK	0x00000001
+#define PLL_NDIV	0x00000800
+#define PLL_DIV		0x00000002
+#define PLL_STATUS	0x00000001
+	u32 unused2[3];
+};
+
+struct tnetd7300_clocks {
+	struct tnetd7300_clock bus;
+	struct tnetd7300_clock cpu;
+	struct tnetd7300_clock usb;
+	struct tnetd7300_clock dsp;
+};
+
+struct tnetd7200_clock {
+	u32 ctrl;
+	u32 unused1[3];
+#define DIVISOR_ENABLE_MASK 0x00008000
+	u32 mul;
+	u32 prediv;
+	u32 postdiv;
+	u32 postdiv2;
+	u32 unused2[6];
+	u32 cmd;
+	u32 status;
+	u32 cmden;
+	u32 padding[15];
+};
+
+struct tnetd7200_clocks {
+	struct tnetd7200_clock cpu;
+	struct tnetd7200_clock dsp;
+	struct tnetd7200_clock usb;
+};
+
+struct clk_rate {
+	u32 rate;
+};
+static struct clk_rate bus_clk = {
+	.rate	= 125000000,
+};
+
+static struct clk_rate cpu_clk = {
+	.rate	= 150000000,
+};
+
+static void approximate(int base, int target, int *prediv,
+			int *postdiv, int *mul)
+{
+	int i, j, k, freq, res = target;
+	for (i = 1; i <= 16; i++)
+		for (j = 1; j <= 32; j++)
+			for (k = 1; k <= 32; k++) {
+				freq = abs(base / j * i / k - target);
+				if (freq < res) {
+					res = freq;
+					*mul = i;
+					*prediv = j;
+					*postdiv = k;
+				}
+			}
+}
+
+static void calculate(int base, int target, int *prediv, int *postdiv,
+	int *mul)
+{
+	int tmp_gcd, tmp_base, tmp_freq;
+
+	for (*prediv = 1; *prediv <= 32; (*prediv)++) {
+		tmp_base = base / *prediv;
+		tmp_gcd = gcd(target, tmp_base);
+		*mul = target / tmp_gcd;
+		*postdiv = tmp_base / tmp_gcd;
+		if ((*mul < 1) || (*mul >= 16))
+			continue;
+		if ((*postdiv > 0) & (*postdiv <= 32))
+			break;
+	}
+
+	if (base / *prediv * *mul / *postdiv != target) {
+		approximate(base, target, prediv, postdiv, mul);
+		tmp_freq = base / *prediv * *mul / *postdiv;
+		printk(KERN_WARNING
+		       "Adjusted requested frequency %d to %d\n",
+		       target, tmp_freq);
+	}
+
+	printk(KERN_DEBUG "Clocks: prediv: %d, postdiv: %d, mul: %d\n",
+	       *prediv, *postdiv, *mul);
+}
+
+static int tnetd7300_dsp_clock(void)
+{
+	u32 didr1, didr2;
+	u8 rev = ar7_chip_rev();
+	didr1 = readl((void *)KSEG1ADDR(AR7_REGS_GPIO + 0x18));
+	didr2 = readl((void *)KSEG1ADDR(AR7_REGS_GPIO + 0x1c));
+	if (didr2 & (1 << 23))
+		return 0;
+	if ((rev >= 0x23) && (rev != 0x57))
+		return 250000000;
+	if ((((didr2 & 0x1fff) << 10) | ((didr1 & 0xffc00000) >> 22))
+	    > 4208000)
+		return 250000000;
+	return 0;
+}
+
+static int tnetd7300_get_clock(u32 shift, struct tnetd7300_clock *clock,
+	u32 *bootcr, u32 bus_clock)
+{
+	int product;
+	int base_clock = AR7_REF_CLOCK;
+	u32 ctrl = readl(&clock->ctrl);
+	u32 pll = readl(&clock->pll);
+	int prediv = ((ctrl & PREDIV_MASK) >> PREDIV_SHIFT) + 1;
+	int postdiv = (ctrl & POSTDIV_MASK) + 1;
+	int divisor = prediv * postdiv;
+	int mul = ((pll & MUL_MASK) >> MUL_SHIFT) + 1;
+
+	switch ((*bootcr & (BOOT_PLL_SOURCE_MASK << shift)) >> shift) {
+	case BOOT_PLL_SOURCE_BUS:
+		base_clock = bus_clock;
+		break;
+	case BOOT_PLL_SOURCE_REF:
+		base_clock = AR7_REF_CLOCK;
+		break;
+	case BOOT_PLL_SOURCE_XTAL:
+		base_clock = AR7_XTAL_CLOCK;
+		break;
+	case BOOT_PLL_SOURCE_CPU:
+		base_clock = cpu_clk.rate;
+		break;
+	}
+
+	if (*bootcr & BOOT_PLL_BYPASS)
+		return base_clock / divisor;
+
+	if ((pll & PLL_MODE_MASK) == 0)
+		return (base_clock >> (mul / 16 + 1)) / divisor;
+
+	if ((pll & (PLL_NDIV | PLL_DIV)) == (PLL_NDIV | PLL_DIV)) {
+		product = (mul & 1) ?
+			(base_clock * mul) >> 1 :
+			(base_clock * (mul - 1)) >> 2;
+		return product / divisor;
+	}
+
+	if (mul == 16)
+		return base_clock / divisor;
+
+	return base_clock * mul / divisor;
+}
+
+static void tnetd7300_set_clock(u32 shift, struct tnetd7300_clock *clock,
+	u32 *bootcr, u32 frequency)
+{
+	int prediv, postdiv, mul;
+	int base_clock = bus_clk.rate;
+
+	switch ((*bootcr & (BOOT_PLL_SOURCE_MASK << shift)) >> shift) {
+	case BOOT_PLL_SOURCE_BUS:
+		base_clock = bus_clk.rate;
+		break;
+	case BOOT_PLL_SOURCE_REF:
+		base_clock = AR7_REF_CLOCK;
+		break;
+	case BOOT_PLL_SOURCE_XTAL:
+		base_clock = AR7_XTAL_CLOCK;
+		break;
+	case BOOT_PLL_SOURCE_CPU:
+		base_clock = cpu_clk.rate;
+		break;
+	}
+
+	calculate(base_clock, frequency, &prediv, &postdiv, &mul);
+
+	writel(((prediv - 1) << PREDIV_SHIFT) | (postdiv - 1), &clock->ctrl);
+	mdelay(1);
+	writel(4, &clock->pll);
+	while (readl(&clock->pll) & PLL_STATUS)
+		;
+	writel(((mul - 1) << MUL_SHIFT) | (0xff << 3) | 0x0e, &clock->pll);
+	mdelay(75);
+}
+
+static void __init tnetd7300_init_clocks(void)
+{
+	u32 *bootcr = (u32 *)ioremap(AR7_REGS_DCL, 4);
+	struct tnetd7300_clocks *clocks =
+					ioremap(UR8_REGS_CLOCKS,
+					sizeof(struct tnetd7300_clocks));
+	u32 dsp_clk;
+	struct clk *clk;
+
+	bus_clk.rate = tnetd7300_get_clock(BUS_PLL_SOURCE_SHIFT,
+		&clocks->bus, bootcr, AR7_AFE_CLOCK);
+
+	if (*bootcr & BOOT_PLL_ASYNC_MODE)
+		cpu_clk.rate = tnetd7300_get_clock(CPU_PLL_SOURCE_SHIFT,
+			&clocks->cpu, bootcr, AR7_AFE_CLOCK);
+	else
+		cpu_clk.rate = bus_clk.rate;
+
+	dsp_clk = tnetd7300_dsp_clock();
+	if (dsp_clk == 250000000)
+		tnetd7300_set_clock(DSP_PLL_SOURCE_SHIFT, &clocks->dsp,
+			bootcr, dsp_clk);
+
+	iounmap(clocks);
+	iounmap(bootcr);
+
+	clk = clk_register_fixed_rate(NULL, "cpu", NULL, 0, cpu_clk.rate);
+	clkdev_create(clk, "cpu", NULL);
+	clk = clk_register_fixed_rate(NULL, "dsp", NULL, 0, dsp_clk);
+	clkdev_create(clk, "dsp", NULL);
+}
+
+static void tnetd7200_set_clock(int base, struct tnetd7200_clock *clock,
+	int prediv, int postdiv, int postdiv2, int mul, u32 frequency)
+{
+	printk(KERN_INFO
+		"Clocks: base = %d, frequency = %u, prediv = %d, "
+		"postdiv = %d, postdiv2 = %d, mul = %d\n",
+		base, frequency, prediv, postdiv, postdiv2, mul);
+
+	writel(0, &clock->ctrl);
+	writel(DIVISOR_ENABLE_MASK | ((prediv - 1) & 0x1F), &clock->prediv);
+	writel((mul - 1) & 0xF, &clock->mul);
+
+	while (readl(&clock->status) & 0x1)
+		; /* nop */
+
+	writel(DIVISOR_ENABLE_MASK | ((postdiv - 1) & 0x1F), &clock->postdiv);
+
+	writel(readl(&clock->cmden) | 1, &clock->cmden);
+	writel(readl(&clock->cmd) | 1, &clock->cmd);
+
+	while (readl(&clock->status) & 0x1)
+		; /* nop */
+
+	writel(DIVISOR_ENABLE_MASK | ((postdiv2 - 1) & 0x1F), &clock->postdiv2);
+
+	writel(readl(&clock->cmden) | 1, &clock->cmden);
+	writel(readl(&clock->cmd) | 1, &clock->cmd);
+
+	while (readl(&clock->status) & 0x1)
+		; /* nop */
+
+	writel(readl(&clock->ctrl) | 1, &clock->ctrl);
+}
+
+static int tnetd7200_get_clock_base(int clock_id, u32 *bootcr)
+{
+	if (*bootcr & BOOT_PLL_ASYNC_MODE)
+		/* Async */
+		switch (clock_id) {
+		case TNETD7200_CLOCK_ID_DSP:
+			return AR7_REF_CLOCK;
+		default:
+			return AR7_AFE_CLOCK;
+		}
+	else
+		/* Sync */
+		if (*bootcr & BOOT_PLL_2TO1_MODE)
+			/* 2:1 */
+			switch (clock_id) {
+			case TNETD7200_CLOCK_ID_DSP:
+				return AR7_REF_CLOCK;
+			default:
+				return AR7_AFE_CLOCK;
+			}
+		else
+			/* 1:1 */
+			return AR7_REF_CLOCK;
+}
+
+
+static void __init tnetd7200_init_clocks(void)
+{
+	u32 *bootcr = (u32 *)ioremap(AR7_REGS_DCL, 4);
+	struct tnetd7200_clocks *clocks =
+					ioremap(AR7_REGS_CLOCKS,
+					sizeof(struct tnetd7200_clocks));
+	int cpu_base, cpu_mul, cpu_prediv, cpu_postdiv;
+	int dsp_base, dsp_mul, dsp_prediv, dsp_postdiv;
+	int usb_base, usb_mul, usb_prediv, usb_postdiv;
+	struct clk *clk;
+
+	cpu_base = tnetd7200_get_clock_base(TNETD7200_CLOCK_ID_CPU, bootcr);
+	dsp_base = tnetd7200_get_clock_base(TNETD7200_CLOCK_ID_DSP, bootcr);
+
+	if (*bootcr & BOOT_PLL_ASYNC_MODE) {
+		printk(KERN_INFO "Clocks: Async mode\n");
+
+		printk(KERN_INFO "Clocks: Setting DSP clock\n");
+		calculate(dsp_base, TNETD7200_DEF_DSP_CLK,
+			&dsp_prediv, &dsp_postdiv, &dsp_mul);
+		bus_clk.rate =
+			((dsp_base / dsp_prediv) * dsp_mul) / dsp_postdiv;
+		tnetd7200_set_clock(dsp_base, &clocks->dsp,
+			dsp_prediv, dsp_postdiv * 2, dsp_postdiv, dsp_mul * 2,
+			bus_clk.rate);
+
+		printk(KERN_INFO "Clocks: Setting CPU clock\n");
+		calculate(cpu_base, TNETD7200_DEF_CPU_CLK, &cpu_prediv,
+			&cpu_postdiv, &cpu_mul);
+		cpu_clk.rate =
+			((cpu_base / cpu_prediv) * cpu_mul) / cpu_postdiv;
+		tnetd7200_set_clock(cpu_base, &clocks->cpu,
+			cpu_prediv, cpu_postdiv, -1, cpu_mul,
+			cpu_clk.rate);
+
+	} else
+		if (*bootcr & BOOT_PLL_2TO1_MODE) {
+			printk(KERN_INFO "Clocks: Sync 2:1 mode\n");
+
+			printk(KERN_INFO "Clocks: Setting CPU clock\n");
+			calculate(cpu_base, TNETD7200_DEF_CPU_CLK, &cpu_prediv,
+				&cpu_postdiv, &cpu_mul);
+			cpu_clk.rate = ((cpu_base / cpu_prediv) * cpu_mul)
+								/ cpu_postdiv;
+			tnetd7200_set_clock(cpu_base, &clocks->cpu,
+				cpu_prediv, cpu_postdiv, -1, cpu_mul,
+				cpu_clk.rate);
+
+			printk(KERN_INFO "Clocks: Setting DSP clock\n");
+			calculate(dsp_base, TNETD7200_DEF_DSP_CLK, &dsp_prediv,
+				&dsp_postdiv, &dsp_mul);
+			bus_clk.rate = cpu_clk.rate / 2;
+			tnetd7200_set_clock(dsp_base, &clocks->dsp,
+				dsp_prediv, dsp_postdiv * 2, dsp_postdiv,
+				dsp_mul * 2, bus_clk.rate);
+		} else {
+			printk(KERN_INFO "Clocks: Sync 1:1 mode\n");
+
+			printk(KERN_INFO "Clocks: Setting DSP clock\n");
+			calculate(dsp_base, TNETD7200_DEF_DSP_CLK, &dsp_prediv,
+				&dsp_postdiv, &dsp_mul);
+			bus_clk.rate = ((dsp_base / dsp_prediv) * dsp_mul)
+								/ dsp_postdiv;
+			tnetd7200_set_clock(dsp_base, &clocks->dsp,
+				dsp_prediv, dsp_postdiv * 2, dsp_postdiv,
+				dsp_mul * 2, bus_clk.rate);
+
+			cpu_clk.rate = bus_clk.rate;
+		}
+
+	printk(KERN_INFO "Clocks: Setting USB clock\n");
+	usb_base = bus_clk.rate;
+	calculate(usb_base, TNETD7200_DEF_USB_CLK, &usb_prediv,
+		&usb_postdiv, &usb_mul);
+	tnetd7200_set_clock(usb_base, &clocks->usb,
+		usb_prediv, usb_postdiv, -1, usb_mul,
+		TNETD7200_DEF_USB_CLK);
+
+	iounmap(clocks);
+	iounmap(bootcr);
+
+	clk = clk_register_fixed_rate(NULL, "cpu", NULL, 0, cpu_clk.rate);
+	clkdev_create(clk, "cpu", NULL);
+	clkdev_create(clk, "dsp", NULL);
+}
+
+void __init ar7_init_clocks(void)
+{
+	struct clk *clk;
+
+	switch (ar7_chip_id()) {
+	case AR7_CHIP_7100:
+	case AR7_CHIP_7200:
+		tnetd7200_init_clocks();
+		break;
+	case AR7_CHIP_7300:
+		tnetd7300_init_clocks();
+		break;
+	default:
+		break;
+	}
+	clk = clk_register_fixed_rate(NULL, "bus", NULL, 0, bus_clk.rate);
+	clkdev_create(clk, "bus", NULL);
+	/* adjust vbus clock rate */
+	clk = clk_register_fixed_factor(NULL, "vbus", "bus", 0, 1, 2);
+	clkdev_create(clk, "vbus", NULL);
+	clkdev_create(clk, "cpmac", "cpmac.1");
+	clkdev_create(clk, "cpmac", "cpmac.1");
+}
diff --git a/arch/mips/ar7/gpio.c b/arch/mips/ar7/gpio.c
new file mode 100644
index 000000000..ae0e01b94
--- /dev/null
+++ b/arch/mips/ar7/gpio.c
@@ -0,0 +1,332 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2007 Felix Fietkau <nbd@openwrt.org>
+ * Copyright (C) 2007 Eugene Konev <ejka@openwrt.org>
+ * Copyright (C) 2009-2010 Florian Fainelli <florian@openwrt.org>
+ */
+
+#include <linux/init.h>
+#include <linux/export.h>
+#include <linux/gpio.h>
+
+#include <asm/mach-ar7/ar7.h>
+
+#define AR7_GPIO_MAX 32
+#define TITAN_GPIO_MAX 51
+
+struct ar7_gpio_chip {
+	void __iomem		*regs;
+	struct gpio_chip	chip;
+};
+
+static int ar7_gpio_get_value(struct gpio_chip *chip, unsigned gpio)
+{
+	struct ar7_gpio_chip *gpch = gpiochip_get_data(chip);
+	void __iomem *gpio_in = gpch->regs + AR7_GPIO_INPUT;
+
+	return !!(readl(gpio_in) & (1 << gpio));
+}
+
+static int titan_gpio_get_value(struct gpio_chip *chip, unsigned gpio)
+{
+	struct ar7_gpio_chip *gpch = gpiochip_get_data(chip);
+	void __iomem *gpio_in0 = gpch->regs + TITAN_GPIO_INPUT_0;
+	void __iomem *gpio_in1 = gpch->regs + TITAN_GPIO_INPUT_1;
+
+	return readl(gpio >> 5 ? gpio_in1 : gpio_in0) & (1 << (gpio & 0x1f));
+}
+
+static void ar7_gpio_set_value(struct gpio_chip *chip,
+				unsigned gpio, int value)
+{
+	struct ar7_gpio_chip *gpch = gpiochip_get_data(chip);
+	void __iomem *gpio_out = gpch->regs + AR7_GPIO_OUTPUT;
+	unsigned tmp;
+
+	tmp = readl(gpio_out) & ~(1 << gpio);
+	if (value)
+		tmp |= 1 << gpio;
+	writel(tmp, gpio_out);
+}
+
+static void titan_gpio_set_value(struct gpio_chip *chip,
+				unsigned gpio, int value)
+{
+	struct ar7_gpio_chip *gpch = gpiochip_get_data(chip);
+	void __iomem *gpio_out0 = gpch->regs + TITAN_GPIO_OUTPUT_0;
+	void __iomem *gpio_out1 = gpch->regs + TITAN_GPIO_OUTPUT_1;
+	unsigned tmp;
+
+	tmp = readl(gpio >> 5 ? gpio_out1 : gpio_out0) & ~(1 << (gpio & 0x1f));
+	if (value)
+		tmp |= 1 << (gpio & 0x1f);
+	writel(tmp, gpio >> 5 ? gpio_out1 : gpio_out0);
+}
+
+static int ar7_gpio_direction_input(struct gpio_chip *chip, unsigned gpio)
+{
+	struct ar7_gpio_chip *gpch = gpiochip_get_data(chip);
+	void __iomem *gpio_dir = gpch->regs + AR7_GPIO_DIR;
+
+	writel(readl(gpio_dir) | (1 << gpio), gpio_dir);
+
+	return 0;
+}
+
+static int titan_gpio_direction_input(struct gpio_chip *chip, unsigned gpio)
+{
+	struct ar7_gpio_chip *gpch = gpiochip_get_data(chip);
+	void __iomem *gpio_dir0 = gpch->regs + TITAN_GPIO_DIR_0;
+	void __iomem *gpio_dir1 = gpch->regs + TITAN_GPIO_DIR_1;
+
+	if (gpio >= TITAN_GPIO_MAX)
+		return -EINVAL;
+
+	writel(readl(gpio >> 5 ? gpio_dir1 : gpio_dir0) | (1 << (gpio & 0x1f)),
+			gpio >> 5 ? gpio_dir1 : gpio_dir0);
+	return 0;
+}
+
+static int ar7_gpio_direction_output(struct gpio_chip *chip,
+					unsigned gpio, int value)
+{
+	struct ar7_gpio_chip *gpch = gpiochip_get_data(chip);
+	void __iomem *gpio_dir = gpch->regs + AR7_GPIO_DIR;
+
+	ar7_gpio_set_value(chip, gpio, value);
+	writel(readl(gpio_dir) & ~(1 << gpio), gpio_dir);
+
+	return 0;
+}
+
+static int titan_gpio_direction_output(struct gpio_chip *chip,
+					unsigned gpio, int value)
+{
+	struct ar7_gpio_chip *gpch = gpiochip_get_data(chip);
+	void __iomem *gpio_dir0 = gpch->regs + TITAN_GPIO_DIR_0;
+	void __iomem *gpio_dir1 = gpch->regs + TITAN_GPIO_DIR_1;
+
+	if (gpio >= TITAN_GPIO_MAX)
+		return -EINVAL;
+
+	titan_gpio_set_value(chip, gpio, value);
+	writel(readl(gpio >> 5 ? gpio_dir1 : gpio_dir0) & ~(1 <<
+		(gpio & 0x1f)), gpio >> 5 ? gpio_dir1 : gpio_dir0);
+
+	return 0;
+}
+
+static struct ar7_gpio_chip ar7_gpio_chip = {
+	.chip = {
+		.label			= "ar7-gpio",
+		.direction_input	= ar7_gpio_direction_input,
+		.direction_output	= ar7_gpio_direction_output,
+		.set			= ar7_gpio_set_value,
+		.get			= ar7_gpio_get_value,
+		.base			= 0,
+		.ngpio			= AR7_GPIO_MAX,
+	}
+};
+
+static struct ar7_gpio_chip titan_gpio_chip = {
+	.chip = {
+		.label			= "titan-gpio",
+		.direction_input	= titan_gpio_direction_input,
+		.direction_output	= titan_gpio_direction_output,
+		.set			= titan_gpio_set_value,
+		.get			= titan_gpio_get_value,
+		.base			= 0,
+		.ngpio			= TITAN_GPIO_MAX,
+	}
+};
+
+static inline int ar7_gpio_enable_ar7(unsigned gpio)
+{
+	void __iomem *gpio_en = ar7_gpio_chip.regs + AR7_GPIO_ENABLE;
+
+	writel(readl(gpio_en) | (1 << gpio), gpio_en);
+
+	return 0;
+}
+
+static inline int ar7_gpio_enable_titan(unsigned gpio)
+{
+	void __iomem *gpio_en0 = titan_gpio_chip.regs  + TITAN_GPIO_ENBL_0;
+	void __iomem *gpio_en1 = titan_gpio_chip.regs  + TITAN_GPIO_ENBL_1;
+
+	writel(readl(gpio >> 5 ? gpio_en1 : gpio_en0) | (1 << (gpio & 0x1f)),
+		gpio >> 5 ? gpio_en1 : gpio_en0);
+
+	return 0;
+}
+
+int ar7_gpio_enable(unsigned gpio)
+{
+	return ar7_is_titan() ? ar7_gpio_enable_titan(gpio) :
+				ar7_gpio_enable_ar7(gpio);
+}
+EXPORT_SYMBOL(ar7_gpio_enable);
+
+static inline int ar7_gpio_disable_ar7(unsigned gpio)
+{
+	void __iomem *gpio_en = ar7_gpio_chip.regs + AR7_GPIO_ENABLE;
+
+	writel(readl(gpio_en) & ~(1 << gpio), gpio_en);
+
+	return 0;
+}
+
+static inline int ar7_gpio_disable_titan(unsigned gpio)
+{
+	void __iomem *gpio_en0 = titan_gpio_chip.regs + TITAN_GPIO_ENBL_0;
+	void __iomem *gpio_en1 = titan_gpio_chip.regs + TITAN_GPIO_ENBL_1;
+
+	writel(readl(gpio >> 5 ? gpio_en1 : gpio_en0) & ~(1 << (gpio & 0x1f)),
+			gpio >> 5 ? gpio_en1 : gpio_en0);
+
+	return 0;
+}
+
+int ar7_gpio_disable(unsigned gpio)
+{
+	return ar7_is_titan() ? ar7_gpio_disable_titan(gpio) :
+				ar7_gpio_disable_ar7(gpio);
+}
+EXPORT_SYMBOL(ar7_gpio_disable);
+
+struct titan_gpio_cfg {
+	u32 reg;
+	u32 shift;
+	u32 func;
+};
+
+static const struct titan_gpio_cfg titan_gpio_table[] = {
+	/* reg, start bit, mux value */
+	{4, 24, 1},
+	{4, 26, 1},
+	{4, 28, 1},
+	{4, 30, 1},
+	{5, 6, 1},
+	{5, 8, 1},
+	{5, 10, 1},
+	{5, 12, 1},
+	{7, 14, 3},
+	{7, 16, 3},
+	{7, 18, 3},
+	{7, 20, 3},
+	{7, 22, 3},
+	{7, 26, 3},
+	{7, 28, 3},
+	{7, 30, 3},
+	{8, 0, 3},
+	{8, 2, 3},
+	{8, 4, 3},
+	{8, 10, 3},
+	{8, 14, 3},
+	{8, 16, 3},
+	{8, 18, 3},
+	{8, 20, 3},
+	{9, 8, 3},
+	{9, 10, 3},
+	{9, 12, 3},
+	{9, 14, 3},
+	{9, 18, 3},
+	{9, 20, 3},
+	{9, 24, 3},
+	{9, 26, 3},
+	{9, 28, 3},
+	{9, 30, 3},
+	{10, 0, 3},
+	{10, 2, 3},
+	{10, 8, 3},
+	{10, 10, 3},
+	{10, 12, 3},
+	{10, 14, 3},
+	{13, 12, 3},
+	{13, 14, 3},
+	{13, 16, 3},
+	{13, 18, 3},
+	{13, 24, 3},
+	{13, 26, 3},
+	{13, 28, 3},
+	{13, 30, 3},
+	{14, 2, 3},
+	{14, 6, 3},
+	{14, 8, 3},
+	{14, 12, 3}
+};
+
+static int titan_gpio_pinsel(unsigned gpio)
+{
+	struct titan_gpio_cfg gpio_cfg;
+	u32 mux_status, pin_sel_reg, tmp;
+	void __iomem *pin_sel = (void __iomem *)KSEG1ADDR(AR7_REGS_PINSEL);
+
+	if (gpio >= ARRAY_SIZE(titan_gpio_table))
+		return -EINVAL;
+
+	gpio_cfg = titan_gpio_table[gpio];
+	pin_sel_reg = gpio_cfg.reg - 1;
+
+	mux_status = (readl(pin_sel + pin_sel_reg) >> gpio_cfg.shift) & 0x3;
+
+	/* Check the mux status */
+	if (!((mux_status == 0) || (mux_status == gpio_cfg.func)))
+		return 0;
+
+	/* Set the pin sel value */
+	tmp = readl(pin_sel + pin_sel_reg);
+	tmp |= ((gpio_cfg.func & 0x3) << gpio_cfg.shift);
+	writel(tmp, pin_sel + pin_sel_reg);
+
+	return 0;
+}
+
+/* Perform minimal Titan GPIO configuration */
+static void titan_gpio_init(void)
+{
+	unsigned i;
+
+	for (i = 44; i < 48; i++) {
+		titan_gpio_pinsel(i);
+		ar7_gpio_enable_titan(i);
+		titan_gpio_direction_input(&titan_gpio_chip.chip, i);
+	}
+}
+
+int __init ar7_gpio_init(void)
+{
+	int ret;
+	struct ar7_gpio_chip *gpch;
+	unsigned size;
+
+	if (!ar7_is_titan()) {
+		gpch = &ar7_gpio_chip;
+		size = 0x10;
+	} else {
+		gpch = &titan_gpio_chip;
+		size = 0x1f;
+	}
+
+	gpch->regs = ioremap(AR7_REGS_GPIO, size);
+	if (!gpch->regs) {
+		printk(KERN_ERR "%s: failed to ioremap regs\n",
+					gpch->chip.label);
+		return -ENOMEM;
+	}
+
+	ret = gpiochip_add_data(&gpch->chip, gpch);
+	if (ret) {
+		printk(KERN_ERR "%s: failed to add gpiochip\n",
+					gpch->chip.label);
+		iounmap(gpch->regs);
+		return ret;
+	}
+	printk(KERN_INFO "%s: registered %d GPIOs\n",
+				gpch->chip.label, gpch->chip.ngpio);
+
+	if (ar7_is_titan())
+		titan_gpio_init();
+
+	return ret;
+}
diff --git a/arch/mips/ar7/irq.c b/arch/mips/ar7/irq.c
new file mode 100644
index 000000000..f0a7942d3
--- /dev/null
+++ b/arch/mips/ar7/irq.c
@@ -0,0 +1,165 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2006,2007 Felix Fietkau <nbd@openwrt.org>
+ * Copyright (C) 2006,2007 Eugene Konev <ejka@openwrt.org>
+ */
+
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+
+#include <asm/irq_cpu.h>
+#include <asm/mipsregs.h>
+#include <asm/mach-ar7/ar7.h>
+
+#define EXCEPT_OFFSET	0x80
+#define PACE_OFFSET	0xA0
+#define CHNLS_OFFSET	0x200
+
+#define REG_OFFSET(irq, reg)	((irq) / 32 * 0x4 + reg * 0x10)
+#define SEC_REG_OFFSET(reg)	(EXCEPT_OFFSET + reg * 0x8)
+#define SEC_SR_OFFSET		(SEC_REG_OFFSET(0))	/* 0x80 */
+#define CR_OFFSET(irq)		(REG_OFFSET(irq, 1))	/* 0x10 */
+#define SEC_CR_OFFSET		(SEC_REG_OFFSET(1))	/* 0x88 */
+#define ESR_OFFSET(irq)		(REG_OFFSET(irq, 2))	/* 0x20 */
+#define SEC_ESR_OFFSET		(SEC_REG_OFFSET(2))	/* 0x90 */
+#define ECR_OFFSET(irq)		(REG_OFFSET(irq, 3))	/* 0x30 */
+#define SEC_ECR_OFFSET		(SEC_REG_OFFSET(3))	/* 0x98 */
+#define PIR_OFFSET		(0x40)
+#define MSR_OFFSET		(0x44)
+#define PM_OFFSET(irq)		(REG_OFFSET(irq, 5))	/* 0x50 */
+#define TM_OFFSET(irq)		(REG_OFFSET(irq, 6))	/* 0x60 */
+
+#define REG(addr) ((u32 *)(KSEG1ADDR(AR7_REGS_IRQ) + addr))
+
+#define CHNL_OFFSET(chnl) (CHNLS_OFFSET + (chnl * 4))
+
+static int ar7_irq_base;
+
+static void ar7_unmask_irq(struct irq_data *d)
+{
+	writel(1 << ((d->irq - ar7_irq_base) % 32),
+	       REG(ESR_OFFSET(d->irq - ar7_irq_base)));
+}
+
+static void ar7_mask_irq(struct irq_data *d)
+{
+	writel(1 << ((d->irq - ar7_irq_base) % 32),
+	       REG(ECR_OFFSET(d->irq - ar7_irq_base)));
+}
+
+static void ar7_ack_irq(struct irq_data *d)
+{
+	writel(1 << ((d->irq - ar7_irq_base) % 32),
+	       REG(CR_OFFSET(d->irq - ar7_irq_base)));
+}
+
+static void ar7_unmask_sec_irq(struct irq_data *d)
+{
+	writel(1 << (d->irq - ar7_irq_base - 40), REG(SEC_ESR_OFFSET));
+}
+
+static void ar7_mask_sec_irq(struct irq_data *d)
+{
+	writel(1 << (d->irq - ar7_irq_base - 40), REG(SEC_ECR_OFFSET));
+}
+
+static void ar7_ack_sec_irq(struct irq_data *d)
+{
+	writel(1 << (d->irq - ar7_irq_base - 40), REG(SEC_CR_OFFSET));
+}
+
+static struct irq_chip ar7_irq_type = {
+	.name = "AR7",
+	.irq_unmask = ar7_unmask_irq,
+	.irq_mask = ar7_mask_irq,
+	.irq_ack = ar7_ack_irq
+};
+
+static struct irq_chip ar7_sec_irq_type = {
+	.name = "AR7",
+	.irq_unmask = ar7_unmask_sec_irq,
+	.irq_mask = ar7_mask_sec_irq,
+	.irq_ack = ar7_ack_sec_irq,
+};
+
+static void __init ar7_irq_init(int base)
+{
+	int i;
+	/*
+	 * Disable interrupts and clear pending
+	 */
+	writel(0xffffffff, REG(ECR_OFFSET(0)));
+	writel(0xff, REG(ECR_OFFSET(32)));
+	writel(0xffffffff, REG(SEC_ECR_OFFSET));
+	writel(0xffffffff, REG(CR_OFFSET(0)));
+	writel(0xff, REG(CR_OFFSET(32)));
+	writel(0xffffffff, REG(SEC_CR_OFFSET));
+
+	ar7_irq_base = base;
+
+	for (i = 0; i < 40; i++) {
+		writel(i, REG(CHNL_OFFSET(i)));
+		/* Primary IRQ's */
+		irq_set_chip_and_handler(base + i, &ar7_irq_type,
+					 handle_level_irq);
+		/* Secondary IRQ's */
+		if (i < 32)
+			irq_set_chip_and_handler(base + i + 40,
+						 &ar7_sec_irq_type,
+						 handle_level_irq);
+	}
+
+	if (request_irq(2, no_action, IRQF_NO_THREAD, "AR7 cascade interrupt",
+			NULL))
+		pr_err("Failed to request irq 2 (AR7 cascade interrupt)\n");
+	if (request_irq(ar7_irq_base, no_action, IRQF_NO_THREAD,
+			"AR7 cascade interrupt", NULL)) {
+		pr_err("Failed to request irq %d (AR7 cascade interrupt)\n",
+		       ar7_irq_base);
+	}
+	set_c0_status(IE_IRQ0);
+}
+
+void __init arch_init_irq(void)
+{
+	mips_cpu_irq_init();
+	ar7_irq_init(8);
+}
+
+static void ar7_cascade(void)
+{
+	u32 status;
+	int i, irq;
+
+	/* Primary IRQ's */
+	irq = readl(REG(PIR_OFFSET)) & 0x3f;
+	if (irq) {
+		do_IRQ(ar7_irq_base + irq);
+		return;
+	}
+
+	/* Secondary IRQ's are cascaded through primary '0' */
+	writel(1, REG(CR_OFFSET(irq)));
+	status = readl(REG(SEC_SR_OFFSET));
+	for (i = 0; i < 32; i++) {
+		if (status & 1) {
+			do_IRQ(ar7_irq_base + i + 40);
+			return;
+		}
+		status >>= 1;
+	}
+
+	spurious_interrupt();
+}
+
+asmlinkage void plat_irq_dispatch(void)
+{
+	unsigned int pending = read_c0_status() & read_c0_cause() & ST0_IM;
+	if (pending & STATUSF_IP7)		/* cpu timer */
+		do_IRQ(7);
+	else if (pending & STATUSF_IP2)		/* int0 hardware line */
+		ar7_cascade();
+	else
+		spurious_interrupt();
+}
diff --git a/arch/mips/ar7/memory.c b/arch/mips/ar7/memory.c
new file mode 100644
index 000000000..ce8024c1a
--- /dev/null
+++ b/arch/mips/ar7/memory.c
@@ -0,0 +1,51 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2007 Felix Fietkau <nbd@openwrt.org>
+ * Copyright (C) 2007 Eugene Konev <ejka@openwrt.org>
+ */
+#include <linux/memblock.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/pfn.h>
+#include <linux/proc_fs.h>
+#include <linux/string.h>
+#include <linux/swap.h>
+
+#include <asm/bootinfo.h>
+#include <asm/page.h>
+#include <asm/sections.h>
+
+#include <asm/mach-ar7/ar7.h>
+
+static int __init memsize(void)
+{
+	u32 size = (64 << 20);
+	u32 *addr = (u32 *)KSEG1ADDR(AR7_SDRAM_BASE + size - 4);
+	u32 *kernel_end = (u32 *)KSEG1ADDR(CPHYSADDR((u32)&_end));
+	u32 *tmpaddr = addr;
+
+	while (tmpaddr > kernel_end) {
+		*tmpaddr = (u32)tmpaddr;
+		size >>= 1;
+		tmpaddr -= size >> 2;
+	}
+
+	do {
+		tmpaddr += size >> 2;
+		if (*tmpaddr != (u32)tmpaddr)
+			break;
+		size <<= 1;
+	} while (size < (64 << 20));
+
+	writel((u32)tmpaddr, &addr);
+
+	return size;
+}
+
+void __init prom_meminit(void)
+{
+	unsigned long pages;
+
+	pages = memsize() >> PAGE_SHIFT;
+	memblock_add(PHYS_OFFSET, pages << PAGE_SHIFT);
+}
diff --git a/arch/mips/ar7/platform.c b/arch/mips/ar7/platform.c
new file mode 100644
index 000000000..215149a85
--- /dev/null
+++ b/arch/mips/ar7/platform.c
@@ -0,0 +1,722 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2006,2007 Felix Fietkau <nbd@openwrt.org>
+ * Copyright (C) 2006,2007 Eugene Konev <ejka@openwrt.org>
+ */
+
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/physmap.h>
+#include <linux/serial.h>
+#include <linux/serial_8250.h>
+#include <linux/ioport.h>
+#include <linux/io.h>
+#include <linux/vlynq.h>
+#include <linux/leds.h>
+#include <linux/string.h>
+#include <linux/etherdevice.h>
+#include <linux/phy.h>
+#include <linux/phy_fixed.h>
+#include <linux/gpio.h>
+#include <linux/clk.h>
+
+#include <asm/addrspace.h>
+#include <asm/mach-ar7/ar7.h>
+#include <asm/mach-ar7/prom.h>
+
+/*****************************************************************************
+ * VLYNQ Bus
+ ****************************************************************************/
+struct plat_vlynq_data {
+	struct plat_vlynq_ops ops;
+	int gpio_bit;
+	int reset_bit;
+};
+
+static int vlynq_on(struct vlynq_device *dev)
+{
+	int ret;
+	struct plat_vlynq_data *pdata = dev->dev.platform_data;
+
+	ret = gpio_request(pdata->gpio_bit, "vlynq");
+	if (ret)
+		goto out;
+
+	ar7_device_reset(pdata->reset_bit);
+
+	ret = ar7_gpio_disable(pdata->gpio_bit);
+	if (ret)
+		goto out_enabled;
+
+	ret = ar7_gpio_enable(pdata->gpio_bit);
+	if (ret)
+		goto out_enabled;
+
+	ret = gpio_direction_output(pdata->gpio_bit, 0);
+	if (ret)
+		goto out_gpio_enabled;
+
+	msleep(50);
+
+	gpio_set_value(pdata->gpio_bit, 1);
+
+	msleep(50);
+
+	return 0;
+
+out_gpio_enabled:
+	ar7_gpio_disable(pdata->gpio_bit);
+out_enabled:
+	ar7_device_disable(pdata->reset_bit);
+	gpio_free(pdata->gpio_bit);
+out:
+	return ret;
+}
+
+static void vlynq_off(struct vlynq_device *dev)
+{
+	struct plat_vlynq_data *pdata = dev->dev.platform_data;
+
+	ar7_gpio_disable(pdata->gpio_bit);
+	gpio_free(pdata->gpio_bit);
+	ar7_device_disable(pdata->reset_bit);
+}
+
+static struct resource vlynq_low_res[] = {
+	{
+		.name	= "regs",
+		.flags	= IORESOURCE_MEM,
+		.start	= AR7_REGS_VLYNQ0,
+		.end	= AR7_REGS_VLYNQ0 + 0xff,
+	},
+	{
+		.name	= "irq",
+		.flags	= IORESOURCE_IRQ,
+		.start	= 29,
+		.end	= 29,
+	},
+	{
+		.name	= "mem",
+		.flags	= IORESOURCE_MEM,
+		.start	= 0x04000000,
+		.end	= 0x04ffffff,
+	},
+	{
+		.name	= "devirq",
+		.flags	= IORESOURCE_IRQ,
+		.start	= 80,
+		.end	= 111,
+	},
+};
+
+static struct resource vlynq_high_res[] = {
+	{
+		.name	= "regs",
+		.flags	= IORESOURCE_MEM,
+		.start	= AR7_REGS_VLYNQ1,
+		.end	= AR7_REGS_VLYNQ1 + 0xff,
+	},
+	{
+		.name	= "irq",
+		.flags	= IORESOURCE_IRQ,
+		.start	= 33,
+		.end	= 33,
+	},
+	{
+		.name	= "mem",
+		.flags	= IORESOURCE_MEM,
+		.start	= 0x0c000000,
+		.end	= 0x0cffffff,
+	},
+	{
+		.name	= "devirq",
+		.flags	= IORESOURCE_IRQ,
+		.start	= 112,
+		.end	= 143,
+	},
+};
+
+static struct plat_vlynq_data vlynq_low_data = {
+	.ops = {
+		.on	= vlynq_on,
+		.off	= vlynq_off,
+	},
+	.reset_bit	= 20,
+	.gpio_bit	= 18,
+};
+
+static struct plat_vlynq_data vlynq_high_data = {
+	.ops = {
+		.on	= vlynq_on,
+		.off	= vlynq_off,
+	},
+	.reset_bit	= 16,
+	.gpio_bit	= 19,
+};
+
+static struct platform_device vlynq_low = {
+	.id		= 0,
+	.name		= "vlynq",
+	.dev = {
+		.platform_data	= &vlynq_low_data,
+	},
+	.resource	= vlynq_low_res,
+	.num_resources	= ARRAY_SIZE(vlynq_low_res),
+};
+
+static struct platform_device vlynq_high = {
+	.id		= 1,
+	.name		= "vlynq",
+	.dev = {
+		.platform_data	= &vlynq_high_data,
+	},
+	.resource	= vlynq_high_res,
+	.num_resources	= ARRAY_SIZE(vlynq_high_res),
+};
+
+/*****************************************************************************
+ * Flash
+ ****************************************************************************/
+static struct resource physmap_flash_resource = {
+	.name	= "mem",
+	.flags	= IORESOURCE_MEM,
+	.start	= 0x10000000,
+	.end	= 0x107fffff,
+};
+
+static const char *ar7_probe_types[] = { "ar7part", NULL };
+
+static struct physmap_flash_data physmap_flash_data = {
+	.width	= 2,
+	.part_probe_types = ar7_probe_types,
+};
+
+static struct platform_device physmap_flash = {
+	.name		= "physmap-flash",
+	.dev = {
+		.platform_data	= &physmap_flash_data,
+	},
+	.resource	= &physmap_flash_resource,
+	.num_resources	= 1,
+};
+
+/*****************************************************************************
+ * Ethernet
+ ****************************************************************************/
+static struct resource cpmac_low_res[] = {
+	{
+		.name	= "regs",
+		.flags	= IORESOURCE_MEM,
+		.start	= AR7_REGS_MAC0,
+		.end	= AR7_REGS_MAC0 + 0x7ff,
+	},
+	{
+		.name	= "irq",
+		.flags	= IORESOURCE_IRQ,
+		.start	= 27,
+		.end	= 27,
+	},
+};
+
+static struct resource cpmac_high_res[] = {
+	{
+		.name	= "regs",
+		.flags	= IORESOURCE_MEM,
+		.start	= AR7_REGS_MAC1,
+		.end	= AR7_REGS_MAC1 + 0x7ff,
+	},
+	{
+		.name	= "irq",
+		.flags	= IORESOURCE_IRQ,
+		.start	= 41,
+		.end	= 41,
+	},
+};
+
+static struct fixed_phy_status fixed_phy_status __initdata = {
+	.link		= 1,
+	.speed		= 100,
+	.duplex		= 1,
+};
+
+static struct plat_cpmac_data cpmac_low_data = {
+	.reset_bit	= 17,
+	.power_bit	= 20,
+	.phy_mask	= 0x80000000,
+};
+
+static struct plat_cpmac_data cpmac_high_data = {
+	.reset_bit	= 21,
+	.power_bit	= 22,
+	.phy_mask	= 0x7fffffff,
+};
+
+static u64 cpmac_dma_mask = DMA_BIT_MASK(32);
+
+static struct platform_device cpmac_low = {
+	.id		= 0,
+	.name		= "cpmac",
+	.dev = {
+		.dma_mask		= &cpmac_dma_mask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+		.platform_data		= &cpmac_low_data,
+	},
+	.resource	= cpmac_low_res,
+	.num_resources	= ARRAY_SIZE(cpmac_low_res),
+};
+
+static struct platform_device cpmac_high = {
+	.id		= 1,
+	.name		= "cpmac",
+	.dev = {
+		.dma_mask		= &cpmac_dma_mask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+		.platform_data		= &cpmac_high_data,
+	},
+	.resource	= cpmac_high_res,
+	.num_resources	= ARRAY_SIZE(cpmac_high_res),
+};
+
+static void __init cpmac_get_mac(int instance, unsigned char *dev_addr)
+{
+	char name[5], *mac;
+
+	sprintf(name, "mac%c", 'a' + instance);
+	mac = prom_getenv(name);
+	if (!mac && instance) {
+		sprintf(name, "mac%c", 'a');
+		mac = prom_getenv(name);
+	}
+
+	if (mac) {
+		if (!mac_pton(mac, dev_addr)) {
+			pr_warn("cannot parse mac address, using random address\n");
+			eth_random_addr(dev_addr);
+		}
+	} else
+		eth_random_addr(dev_addr);
+}
+
+/*****************************************************************************
+ * USB
+ ****************************************************************************/
+static struct resource usb_res[] = {
+	{
+		.name	= "regs",
+		.flags	= IORESOURCE_MEM,
+		.start	= AR7_REGS_USB,
+		.end	= AR7_REGS_USB + 0xff,
+	},
+	{
+		.name	= "irq",
+		.flags	= IORESOURCE_IRQ,
+		.start	= 32,
+		.end	= 32,
+	},
+	{
+		.name	= "mem",
+		.flags	= IORESOURCE_MEM,
+		.start	= 0x03400000,
+		.end	= 0x03401fff,
+	},
+};
+
+static struct platform_device ar7_udc = {
+	.name		= "ar7_udc",
+	.resource	= usb_res,
+	.num_resources	= ARRAY_SIZE(usb_res),
+};
+
+/*****************************************************************************
+ * LEDs
+ ****************************************************************************/
+static const struct gpio_led default_leds[] = {
+	{
+		.name			= "status",
+		.gpio			= 8,
+		.active_low		= 1,
+	},
+};
+
+static const struct gpio_led titan_leds[] = {
+	{ .name = "status", .gpio = 8, .active_low = 1, },
+	{ .name = "wifi", .gpio = 13, .active_low = 1, },
+};
+
+static const struct gpio_led dsl502t_leds[] = {
+	{
+		.name			= "status",
+		.gpio			= 9,
+		.active_low		= 1,
+	},
+	{
+		.name			= "ethernet",
+		.gpio			= 7,
+		.active_low		= 1,
+	},
+	{
+		.name			= "usb",
+		.gpio			= 12,
+		.active_low		= 1,
+	},
+};
+
+static const struct gpio_led dg834g_leds[] = {
+	{
+		.name			= "ppp",
+		.gpio			= 6,
+		.active_low		= 1,
+	},
+	{
+		.name			= "status",
+		.gpio			= 7,
+		.active_low		= 1,
+	},
+	{
+		.name			= "adsl",
+		.gpio			= 8,
+		.active_low		= 1,
+	},
+	{
+		.name			= "wifi",
+		.gpio			= 12,
+		.active_low		= 1,
+	},
+	{
+		.name			= "power",
+		.gpio			= 14,
+		.active_low		= 1,
+		.default_trigger	= "default-on",
+	},
+};
+
+static const struct gpio_led fb_sl_leds[] = {
+	{
+		.name			= "1",
+		.gpio			= 7,
+	},
+	{
+		.name			= "2",
+		.gpio			= 13,
+		.active_low		= 1,
+	},
+	{
+		.name			= "3",
+		.gpio			= 10,
+		.active_low		= 1,
+	},
+	{
+		.name			= "4",
+		.gpio			= 12,
+		.active_low		= 1,
+	},
+	{
+		.name			= "5",
+		.gpio			= 9,
+		.active_low		= 1,
+	},
+};
+
+static const struct gpio_led fb_fon_leds[] = {
+	{
+		.name			= "1",
+		.gpio			= 8,
+	},
+	{
+		.name			= "2",
+		.gpio			= 3,
+		.active_low		= 1,
+	},
+	{
+		.name			= "3",
+		.gpio			= 5,
+	},
+	{
+		.name			= "4",
+		.gpio			= 4,
+		.active_low		= 1,
+	},
+	{
+		.name			= "5",
+		.gpio			= 11,
+		.active_low		= 1,
+	},
+};
+
+static const struct gpio_led gt701_leds[] = {
+	{
+		.name			= "inet:green",
+		.gpio			= 13,
+		.active_low		= 1,
+	},
+	{
+		.name			= "usb",
+		.gpio			= 12,
+		.active_low		= 1,
+	},
+	{
+		.name			= "inet:red",
+		.gpio			= 9,
+		.active_low		= 1,
+	},
+	{
+		.name			= "power:red",
+		.gpio			= 7,
+		.active_low		= 1,
+	},
+	{
+		.name			= "power:green",
+		.gpio			= 8,
+		.active_low		= 1,
+		.default_trigger	= "default-on",
+	},
+	{
+		.name			= "ethernet",
+		.gpio			= 10,
+		.active_low		= 1,
+	},
+};
+
+static struct gpio_led_platform_data ar7_led_data;
+
+static struct platform_device ar7_gpio_leds = {
+	.name = "leds-gpio",
+	.dev = {
+		.platform_data = &ar7_led_data,
+	}
+};
+
+static void __init detect_leds(void)
+{
+	char *prid, *usb_prod;
+
+	/* Default LEDs */
+	ar7_led_data.num_leds = ARRAY_SIZE(default_leds);
+	ar7_led_data.leds = default_leds;
+
+	/* FIXME: the whole thing is unreliable */
+	prid = prom_getenv("ProductID");
+	usb_prod = prom_getenv("usb_prod");
+
+	/* If we can't get the product id from PROM, use the default LEDs */
+	if (!prid)
+		return;
+
+	if (strstr(prid, "Fritz_Box_FON")) {
+		ar7_led_data.num_leds = ARRAY_SIZE(fb_fon_leds);
+		ar7_led_data.leds = fb_fon_leds;
+	} else if (strstr(prid, "Fritz_Box_")) {
+		ar7_led_data.num_leds = ARRAY_SIZE(fb_sl_leds);
+		ar7_led_data.leds = fb_sl_leds;
+	} else if ((!strcmp(prid, "AR7RD") || !strcmp(prid, "AR7DB"))
+		&& usb_prod != NULL && strstr(usb_prod, "DSL-502T")) {
+		ar7_led_data.num_leds = ARRAY_SIZE(dsl502t_leds);
+		ar7_led_data.leds = dsl502t_leds;
+	} else if (strstr(prid, "DG834")) {
+		ar7_led_data.num_leds = ARRAY_SIZE(dg834g_leds);
+		ar7_led_data.leds = dg834g_leds;
+	} else if (strstr(prid, "CYWM") || strstr(prid, "CYWL")) {
+		ar7_led_data.num_leds = ARRAY_SIZE(titan_leds);
+		ar7_led_data.leds = titan_leds;
+	} else if (strstr(prid, "GT701")) {
+		ar7_led_data.num_leds = ARRAY_SIZE(gt701_leds);
+		ar7_led_data.leds = gt701_leds;
+	}
+}
+
+/*****************************************************************************
+ * Watchdog
+ ****************************************************************************/
+static struct resource ar7_wdt_res = {
+	.name		= "regs",
+	.flags		= IORESOURCE_MEM,
+	.start		= -1,	/* Filled at runtime */
+	.end		= -1,	/* Filled at runtime */
+};
+
+static struct platform_device ar7_wdt = {
+	.name		= "ar7_wdt",
+	.resource	= &ar7_wdt_res,
+	.num_resources	= 1,
+};
+
+/*****************************************************************************
+ * Init
+ ****************************************************************************/
+static int __init ar7_register_uarts(void)
+{
+#ifdef CONFIG_SERIAL_8250
+	static struct uart_port uart_port __initdata;
+	struct clk *bus_clk;
+	int res;
+
+	memset(&uart_port, 0, sizeof(struct uart_port));
+
+	bus_clk = clk_get(NULL, "bus");
+	if (IS_ERR(bus_clk))
+		panic("unable to get bus clk");
+
+	uart_port.type		= PORT_AR7;
+	uart_port.uartclk	= clk_get_rate(bus_clk) / 2;
+	uart_port.iotype	= UPIO_MEM32;
+	uart_port.flags		= UPF_FIXED_TYPE | UPF_BOOT_AUTOCONF;
+	uart_port.regshift	= 2;
+
+	uart_port.line		= 0;
+	uart_port.irq		= AR7_IRQ_UART0;
+	uart_port.mapbase	= AR7_REGS_UART0;
+	uart_port.membase	= ioremap(uart_port.mapbase, 256);
+
+	res = early_serial_setup(&uart_port);
+	if (res)
+		return res;
+
+	/* Only TNETD73xx have a second serial port */
+	if (ar7_has_second_uart()) {
+		uart_port.line		= 1;
+		uart_port.irq		= AR7_IRQ_UART1;
+		uart_port.mapbase	= UR8_REGS_UART1;
+		uart_port.membase	= ioremap(uart_port.mapbase, 256);
+
+		res = early_serial_setup(&uart_port);
+		if (res)
+			return res;
+	}
+#endif
+
+	return 0;
+}
+
+static void __init titan_fixup_devices(void)
+{
+	/* Set vlynq0 data */
+	vlynq_low_data.reset_bit = 15;
+	vlynq_low_data.gpio_bit = 14;
+
+	/* Set vlynq1 data */
+	vlynq_high_data.reset_bit = 16;
+	vlynq_high_data.gpio_bit = 7;
+
+	/* Set vlynq0 resources */
+	vlynq_low_res[0].start = TITAN_REGS_VLYNQ0;
+	vlynq_low_res[0].end = TITAN_REGS_VLYNQ0 + 0xff;
+	vlynq_low_res[1].start = 33;
+	vlynq_low_res[1].end = 33;
+	vlynq_low_res[2].start = 0x0c000000;
+	vlynq_low_res[2].end = 0x0fffffff;
+	vlynq_low_res[3].start = 80;
+	vlynq_low_res[3].end = 111;
+
+	/* Set vlynq1 resources */
+	vlynq_high_res[0].start = TITAN_REGS_VLYNQ1;
+	vlynq_high_res[0].end = TITAN_REGS_VLYNQ1 + 0xff;
+	vlynq_high_res[1].start = 34;
+	vlynq_high_res[1].end = 34;
+	vlynq_high_res[2].start = 0x40000000;
+	vlynq_high_res[2].end = 0x43ffffff;
+	vlynq_high_res[3].start = 112;
+	vlynq_high_res[3].end = 143;
+
+	/* Set cpmac0 data */
+	cpmac_low_data.phy_mask = 0x40000000;
+
+	/* Set cpmac1 data */
+	cpmac_high_data.phy_mask = 0x80000000;
+
+	/* Set cpmac0 resources */
+	cpmac_low_res[0].start = TITAN_REGS_MAC0;
+	cpmac_low_res[0].end = TITAN_REGS_MAC0 + 0x7ff;
+
+	/* Set cpmac1 resources */
+	cpmac_high_res[0].start = TITAN_REGS_MAC1;
+	cpmac_high_res[0].end = TITAN_REGS_MAC1 + 0x7ff;
+}
+
+static int __init ar7_register_devices(void)
+{
+	void __iomem *bootcr;
+	u32 val;
+	int res;
+
+	res = ar7_gpio_init();
+	if (res)
+		pr_warn("unable to register gpios: %d\n", res);
+
+	res = ar7_register_uarts();
+	if (res)
+		pr_err("unable to setup uart(s): %d\n", res);
+
+	res = platform_device_register(&physmap_flash);
+	if (res)
+		pr_warn("unable to register physmap-flash: %d\n", res);
+
+	if (ar7_is_titan())
+		titan_fixup_devices();
+
+	ar7_device_disable(vlynq_low_data.reset_bit);
+	res = platform_device_register(&vlynq_low);
+	if (res)
+		pr_warn("unable to register vlynq-low: %d\n", res);
+
+	if (ar7_has_high_vlynq()) {
+		ar7_device_disable(vlynq_high_data.reset_bit);
+		res = platform_device_register(&vlynq_high);
+		if (res)
+			pr_warn("unable to register vlynq-high: %d\n", res);
+	}
+
+	if (ar7_has_high_cpmac()) {
+		res = fixed_phy_add(PHY_POLL, cpmac_high.id,
+				    &fixed_phy_status);
+		if (!res) {
+			cpmac_get_mac(1, cpmac_high_data.dev_addr);
+
+			res = platform_device_register(&cpmac_high);
+			if (res)
+				pr_warn("unable to register cpmac-high: %d\n",
+					res);
+		} else
+			pr_warn("unable to add cpmac-high phy: %d\n", res);
+	} else
+		cpmac_low_data.phy_mask = 0xffffffff;
+
+	res = fixed_phy_add(PHY_POLL, cpmac_low.id, &fixed_phy_status);
+	if (!res) {
+		cpmac_get_mac(0, cpmac_low_data.dev_addr);
+		res = platform_device_register(&cpmac_low);
+		if (res)
+			pr_warn("unable to register cpmac-low: %d\n", res);
+	} else
+		pr_warn("unable to add cpmac-low phy: %d\n", res);
+
+	detect_leds();
+	res = platform_device_register(&ar7_gpio_leds);
+	if (res)
+		pr_warn("unable to register leds: %d\n", res);
+
+	res = platform_device_register(&ar7_udc);
+	if (res)
+		pr_warn("unable to register usb slave: %d\n", res);
+
+	/* Register watchdog only if enabled in hardware */
+	bootcr = ioremap(AR7_REGS_DCL, 4);
+	val = readl(bootcr);
+	iounmap(bootcr);
+	if (val & AR7_WDT_HW_ENA) {
+		if (ar7_has_high_vlynq())
+			ar7_wdt_res.start = UR8_REGS_WDT;
+		else
+			ar7_wdt_res.start = AR7_REGS_WDT;
+
+		ar7_wdt_res.end = ar7_wdt_res.start + 0x20;
+		res = platform_device_register(&ar7_wdt);
+		if (res)
+			pr_warn("unable to register watchdog: %d\n", res);
+	}
+
+	return 0;
+}
+device_initcall(ar7_register_devices);
diff --git a/arch/mips/ar7/prom.c b/arch/mips/ar7/prom.c
new file mode 100644
index 000000000..5810d3993
--- /dev/null
+++ b/arch/mips/ar7/prom.c
@@ -0,0 +1,256 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 1999,2000 MIPS Technologies, Inc.  All rights reserved.
+ *
+ * Putting things on the screen/serial line using YAMONs facilities.
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/serial_reg.h>
+#include <linux/spinlock.h>
+#include <linux/export.h>
+#include <linux/string.h>
+#include <linux/io.h>
+#include <asm/bootinfo.h>
+#include <asm/setup.h>
+
+#include <asm/mach-ar7/ar7.h>
+#include <asm/mach-ar7/prom.h>
+
+#define MAX_ENTRY 80
+
+struct env_var {
+	char	*name;
+	char	*value;
+};
+
+static struct env_var adam2_env[MAX_ENTRY];
+
+char *prom_getenv(const char *name)
+{
+	int i;
+
+	for (i = 0; (i < MAX_ENTRY) && adam2_env[i].name; i++)
+		if (!strcmp(name, adam2_env[i].name))
+			return adam2_env[i].value;
+
+	return NULL;
+}
+EXPORT_SYMBOL(prom_getenv);
+
+static void  __init ar7_init_cmdline(int argc, char *argv[])
+{
+	int i;
+
+	for (i = 1; i < argc; i++) {
+		strlcat(arcs_cmdline, argv[i], COMMAND_LINE_SIZE);
+		if (i < (argc - 1))
+			strlcat(arcs_cmdline, " ", COMMAND_LINE_SIZE);
+	}
+}
+
+struct psbl_rec {
+	u32	psbl_size;
+	u32	env_base;
+	u32	env_size;
+	u32	ffs_base;
+	u32	ffs_size;
+};
+
+static const char psp_env_version[] __initconst = "TIENV0.8";
+
+struct psp_env_chunk {
+	u8	num;
+	u8	ctrl;
+	u16	csum;
+	u8	len;
+	char	data[11];
+} __packed;
+
+struct psp_var_map_entry {
+	u8	num;
+	char	*value;
+};
+
+static const struct psp_var_map_entry psp_var_map[] = {
+	{  1,	"cpufrequency" },
+	{  2,	"memsize" },
+	{  3,	"flashsize" },
+	{  4,	"modetty0" },
+	{  5,	"modetty1" },
+	{  8,	"maca" },
+	{  9,	"macb" },
+	{ 28,	"sysfrequency" },
+	{ 38,	"mipsfrequency" },
+};
+
+/*
+
+Well-known variable (num is looked up in table above for matching variable name)
+Example: cpufrequency=211968000
++----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---
+| 01 |CTRL|CHECKSUM | 01 | _2 | _1 | _1 | _9 | _6 | _8 | _0 | _0 | _0 | \0 | FF
++----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---
+
+Name=Value pair in a single chunk
+Example: NAME=VALUE
++----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---
+| 00 |CTRL|CHECKSUM | 01 | _N | _A | _M | _E | _0 | _V | _A | _L | _U | _E | \0
++----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---
+
+Name=Value pair in 2 chunks (len is the number of chunks)
+Example: bootloaderVersion=1.3.7.15
++----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---
+| 00 |CTRL|CHECKSUM | 02 | _b | _o | _o | _t | _l | _o | _a | _d | _e | _r | _V
++----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---
+| _e | _r | _s | _i | _o | _n | \0 | _1 | _. | _3 | _. | _7 | _. | _1 | _5 | \0
++----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---
+
+Data is padded with 0xFF
+
+*/
+
+#define PSP_ENV_SIZE  4096
+
+static char psp_env_data[PSP_ENV_SIZE] = { 0, };
+
+static char * __init lookup_psp_var_map(u8 num)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(psp_var_map); i++)
+		if (psp_var_map[i].num == num)
+			return psp_var_map[i].value;
+
+	return NULL;
+}
+
+static void __init add_adam2_var(char *name, char *value)
+{
+	int i;
+
+	for (i = 0; i < MAX_ENTRY; i++) {
+		if (!adam2_env[i].name) {
+			adam2_env[i].name = name;
+			adam2_env[i].value = value;
+			return;
+		} else if (!strcmp(adam2_env[i].name, name)) {
+			adam2_env[i].value = value;
+			return;
+		}
+	}
+}
+
+static int __init parse_psp_env(void *psp_env_base)
+{
+	int i, n;
+	char *name, *value;
+	struct psp_env_chunk *chunks = (struct psp_env_chunk *)psp_env_data;
+
+	memcpy_fromio(chunks, psp_env_base, PSP_ENV_SIZE);
+
+	i = 1;
+	n = PSP_ENV_SIZE / sizeof(struct psp_env_chunk);
+	while (i < n) {
+		if ((chunks[i].num == 0xff) || ((i + chunks[i].len) > n))
+			break;
+		value = chunks[i].data;
+		if (chunks[i].num) {
+			name = lookup_psp_var_map(chunks[i].num);
+		} else {
+			name = value;
+			value += strlen(name) + 1;
+		}
+		if (name)
+			add_adam2_var(name, value);
+		i += chunks[i].len;
+	}
+	return 0;
+}
+
+static void __init ar7_init_env(struct env_var *env)
+{
+	int i;
+	struct psbl_rec *psbl = (struct psbl_rec *)(KSEG1ADDR(0x14000300));
+	void *psp_env = (void *)KSEG1ADDR(psbl->env_base);
+
+	if (strcmp(psp_env, psp_env_version) == 0) {
+		parse_psp_env(psp_env);
+	} else {
+		for (i = 0; i < MAX_ENTRY; i++, env++)
+			if (env->name)
+				add_adam2_var(env->name, env->value);
+	}
+}
+
+static void __init console_config(void)
+{
+#ifdef CONFIG_SERIAL_8250_CONSOLE
+	char console_string[40];
+	int baud = 0;
+	char parity = '\0', bits = '\0', flow = '\0';
+	char *s, *p;
+
+	if (strstr(arcs_cmdline, "console="))
+		return;
+
+	s = prom_getenv("modetty0");
+	if (s) {
+		baud = simple_strtoul(s, &p, 10);
+		s = p;
+		if (*s == ',')
+			s++;
+		if (*s)
+			parity = *s++;
+		if (*s == ',')
+			s++;
+		if (*s)
+			bits = *s++;
+		if (*s == ',')
+			s++;
+		if (*s == 'h')
+			flow = 'r';
+	}
+
+	if (baud == 0)
+		baud = 38400;
+	if (parity != 'n' && parity != 'o' && parity != 'e')
+		parity = 'n';
+	if (bits != '7' && bits != '8')
+		bits = '8';
+
+	if (flow == 'r')
+		sprintf(console_string, " console=ttyS0,%d%c%c%c", baud,
+			parity, bits, flow);
+	else
+		sprintf(console_string, " console=ttyS0,%d%c%c", baud, parity,
+			bits);
+	strlcat(arcs_cmdline, console_string, COMMAND_LINE_SIZE);
+#endif
+}
+
+void __init prom_init(void)
+{
+	ar7_init_cmdline(fw_arg0, (char **)fw_arg1);
+	ar7_init_env((struct env_var *)fw_arg2);
+	console_config();
+}
+
+#define PORT(offset) (KSEG1ADDR(AR7_REGS_UART0 + (offset * 4)))
+static inline unsigned int serial_in(int offset)
+{
+	return readl((void *)PORT(offset));
+}
+
+static inline void serial_out(int offset, int value)
+{
+	writel(value, (void *)PORT(offset));
+}
+
+void prom_putchar(char c)
+{
+	while ((serial_in(UART_LSR) & UART_LSR_TEMT) == 0)
+		;
+	serial_out(UART_TX, c);
+}
diff --git a/arch/mips/ar7/setup.c b/arch/mips/ar7/setup.c
new file mode 100644
index 000000000..352d5dbc7
--- /dev/null
+++ b/arch/mips/ar7/setup.c
@@ -0,0 +1,93 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 2000 MIPS Technologies, Inc.  All rights reserved.
+ */
+#include <linux/init.h>
+#include <linux/ioport.h>
+#include <linux/pm.h>
+#include <linux/time.h>
+
+#include <asm/reboot.h>
+#include <asm/mach-ar7/ar7.h>
+#include <asm/mach-ar7/prom.h>
+
+static void ar7_machine_restart(char *command)
+{
+	u32 *softres_reg = ioremap(AR7_REGS_RESET + AR7_RESET_SOFTWARE, 1);
+
+	writel(1, softres_reg);
+}
+
+static void ar7_machine_halt(void)
+{
+	while (1)
+		;
+}
+
+static void ar7_machine_power_off(void)
+{
+	u32 *power_reg = (u32 *)ioremap(AR7_REGS_POWER, 1);
+	u32 power_state = readl(power_reg) | (3 << 30);
+
+	writel(power_state, power_reg);
+	ar7_machine_halt();
+}
+
+const char *get_system_type(void)
+{
+	u16 chip_id = ar7_chip_id();
+	u16 titan_variant_id = titan_chip_id();
+
+	switch (chip_id) {
+	case AR7_CHIP_7100:
+		return "TI AR7 (TNETD7100)";
+	case AR7_CHIP_7200:
+		return "TI AR7 (TNETD7200)";
+	case AR7_CHIP_7300:
+		return "TI AR7 (TNETD7300)";
+	case AR7_CHIP_TITAN:
+		switch (titan_variant_id) {
+		case TITAN_CHIP_1050:
+			return "TI AR7 (TNETV1050)";
+		case TITAN_CHIP_1055:
+			return "TI AR7 (TNETV1055)";
+		case TITAN_CHIP_1056:
+			return "TI AR7 (TNETV1056)";
+		case TITAN_CHIP_1060:
+			return "TI AR7 (TNETV1060)";
+		}
+		fallthrough;
+	default:
+		return "TI AR7 (unknown)";
+	}
+}
+
+static int __init ar7_init_console(void)
+{
+	return 0;
+}
+console_initcall(ar7_init_console);
+
+/*
+ * Initializes basic routines and structures pointers, memory size (as
+ * given by the bios and saves the command line.
+ */
+void __init plat_mem_setup(void)
+{
+	unsigned long io_base;
+
+	_machine_restart = ar7_machine_restart;
+	_machine_halt = ar7_machine_halt;
+	pm_power_off = ar7_machine_power_off;
+
+	io_base = (unsigned long)ioremap(AR7_REGS_BASE, 0x10000);
+	if (!io_base)
+		panic("Can't remap IO base!");
+	set_io_port_base(io_base);
+
+	prom_meminit();
+
+	printk(KERN_INFO "%s, ID: 0x%04x, Revision: 0x%02x\n",
+			get_system_type(), ar7_chip_id(), ar7_chip_rev());
+}
diff --git a/arch/mips/ar7/time.c b/arch/mips/ar7/time.c
new file mode 100644
index 000000000..72aa77d70
--- /dev/null
+++ b/arch/mips/ar7/time.c
@@ -0,0 +1,31 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 1999,2000 MIPS Technologies, Inc.  All rights reserved.
+ *
+ * Setting up the clock on the MIPS boards.
+ */
+
+#include <linux/init.h>
+#include <linux/time.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+
+#include <asm/time.h>
+#include <asm/mach-ar7/ar7.h>
+
+void __init plat_time_init(void)
+{
+	struct clk *cpu_clk;
+
+	/* Initialize ar7 clocks so the CPU clock frequency is correct */
+	ar7_init_clocks();
+
+	cpu_clk = clk_get(NULL, "cpu");
+	if (IS_ERR(cpu_clk)) {
+		printk(KERN_ERR "unable to get cpu clock\n");
+		return;
+	}
+
+	mips_hpt_frequency = clk_get_rate(cpu_clk) / 2;
+}
diff --git a/arch/mips/ath25/Kconfig b/arch/mips/ath25/Kconfig
new file mode 100644
index 000000000..3014c80cf
--- /dev/null
+++ b/arch/mips/ath25/Kconfig
@@ -0,0 +1,17 @@
+# SPDX-License-Identifier: GPL-2.0
+config SOC_AR5312
+	bool "Atheros AR5312/AR2312+ SoC support"
+	depends on ATH25
+	default y
+
+config SOC_AR2315
+	bool "Atheros AR2315+ SoC support"
+	depends on ATH25
+	default y
+
+config PCI_AR2315
+	bool "Atheros AR2315 PCI controller support"
+	depends on SOC_AR2315
+	select ARCH_HAS_PHYS_TO_DMA
+	select FORCE_PCI
+	default y
diff --git a/arch/mips/ath25/Makefile b/arch/mips/ath25/Makefile
new file mode 100644
index 000000000..eabad7da4
--- /dev/null
+++ b/arch/mips/ath25/Makefile
@@ -0,0 +1,16 @@
+#
+# This file is subject to the terms and conditions of the GNU General Public
+# License.  See the file "COPYING" in the main directory of this archive
+# for more details.
+#
+# Copyright (C) 2006 FON Technology, SL.
+# Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
+# Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
+#
+
+obj-y += board.o prom.o devices.o
+
+obj-$(CONFIG_EARLY_PRINTK) += early_printk.o
+
+obj-$(CONFIG_SOC_AR5312) += ar5312.o
+obj-$(CONFIG_SOC_AR2315) += ar2315.o
diff --git a/arch/mips/ath25/Platform b/arch/mips/ath25/Platform
new file mode 100644
index 000000000..aef098b6f
--- /dev/null
+++ b/arch/mips/ath25/Platform
@@ -0,0 +1,5 @@
+#
+# Atheros AR531X/AR231X WiSoC
+#
+cflags-$(CONFIG_ATH25)		+= -I$(srctree)/arch/mips/include/asm/mach-ath25
+load-$(CONFIG_ATH25)		+= 0xffffffff80041000
diff --git a/arch/mips/ath25/ar2315.c b/arch/mips/ath25/ar2315.c
new file mode 100644
index 000000000..8ccf167c1
--- /dev/null
+++ b/arch/mips/ath25/ar2315.c
@@ -0,0 +1,362 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003 Atheros Communications, Inc.,  All Rights Reserved.
+ * Copyright (C) 2006 FON Technology, SL.
+ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
+ * Copyright (C) 2006 Felix Fietkau <nbd@openwrt.org>
+ * Copyright (C) 2012 Alexandros C. Couloumbis <alex@ozo.com>
+ */
+
+/*
+ * Platform devices for Atheros AR2315 SoCs
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/bitops.h>
+#include <linux/irqdomain.h>
+#include <linux/interrupt.h>
+#include <linux/memblock.h>
+#include <linux/platform_device.h>
+#include <linux/reboot.h>
+#include <asm/bootinfo.h>
+#include <asm/reboot.h>
+#include <asm/time.h>
+
+#include <ath25_platform.h>
+
+#include "devices.h"
+#include "ar2315.h"
+#include "ar2315_regs.h"
+
+static void __iomem *ar2315_rst_base;
+static struct irq_domain *ar2315_misc_irq_domain;
+
+static inline u32 ar2315_rst_reg_read(u32 reg)
+{
+	return __raw_readl(ar2315_rst_base + reg);
+}
+
+static inline void ar2315_rst_reg_write(u32 reg, u32 val)
+{
+	__raw_writel(val, ar2315_rst_base + reg);
+}
+
+static inline void ar2315_rst_reg_mask(u32 reg, u32 mask, u32 val)
+{
+	u32 ret = ar2315_rst_reg_read(reg);
+
+	ret &= ~mask;
+	ret |= val;
+	ar2315_rst_reg_write(reg, ret);
+}
+
+static irqreturn_t ar2315_ahb_err_handler(int cpl, void *dev_id)
+{
+	ar2315_rst_reg_write(AR2315_AHB_ERR0, AR2315_AHB_ERROR_DET);
+	ar2315_rst_reg_read(AR2315_AHB_ERR1);
+
+	pr_emerg("AHB fatal error\n");
+	machine_restart("AHB error"); /* Catastrophic failure */
+
+	return IRQ_HANDLED;
+}
+
+static void ar2315_misc_irq_handler(struct irq_desc *desc)
+{
+	u32 pending = ar2315_rst_reg_read(AR2315_ISR) &
+		      ar2315_rst_reg_read(AR2315_IMR);
+	unsigned nr;
+	int ret = 0;
+
+	if (pending) {
+		struct irq_domain *domain = irq_desc_get_handler_data(desc);
+
+		nr = __ffs(pending);
+
+		if (nr == AR2315_MISC_IRQ_GPIO)
+			ar2315_rst_reg_write(AR2315_ISR, AR2315_ISR_GPIO);
+		else if (nr == AR2315_MISC_IRQ_WATCHDOG)
+			ar2315_rst_reg_write(AR2315_ISR, AR2315_ISR_WD);
+
+		ret = generic_handle_domain_irq(domain, nr);
+	}
+
+	if (!pending || ret)
+		spurious_interrupt();
+}
+
+static void ar2315_misc_irq_unmask(struct irq_data *d)
+{
+	ar2315_rst_reg_mask(AR2315_IMR, 0, BIT(d->hwirq));
+}
+
+static void ar2315_misc_irq_mask(struct irq_data *d)
+{
+	ar2315_rst_reg_mask(AR2315_IMR, BIT(d->hwirq), 0);
+}
+
+static struct irq_chip ar2315_misc_irq_chip = {
+	.name		= "ar2315-misc",
+	.irq_unmask	= ar2315_misc_irq_unmask,
+	.irq_mask	= ar2315_misc_irq_mask,
+};
+
+static int ar2315_misc_irq_map(struct irq_domain *d, unsigned irq,
+			       irq_hw_number_t hw)
+{
+	irq_set_chip_and_handler(irq, &ar2315_misc_irq_chip, handle_level_irq);
+	return 0;
+}
+
+static const struct irq_domain_ops ar2315_misc_irq_domain_ops = {
+	.map = ar2315_misc_irq_map,
+};
+
+/*
+ * Called when an interrupt is received, this function
+ * determines exactly which interrupt it was, and it
+ * invokes the appropriate handler.
+ *
+ * Implicitly, we also define interrupt priority by
+ * choosing which to dispatch first.
+ */
+static void ar2315_irq_dispatch(void)
+{
+	u32 pending = read_c0_status() & read_c0_cause();
+
+	if (pending & CAUSEF_IP3)
+		do_IRQ(AR2315_IRQ_WLAN0);
+#ifdef CONFIG_PCI_AR2315
+	else if (pending & CAUSEF_IP5)
+		do_IRQ(AR2315_IRQ_LCBUS_PCI);
+#endif
+	else if (pending & CAUSEF_IP2)
+		do_IRQ(AR2315_IRQ_MISC);
+	else if (pending & CAUSEF_IP7)
+		do_IRQ(ATH25_IRQ_CPU_CLOCK);
+	else
+		spurious_interrupt();
+}
+
+void __init ar2315_arch_init_irq(void)
+{
+	struct irq_domain *domain;
+	unsigned irq;
+
+	ath25_irq_dispatch = ar2315_irq_dispatch;
+
+	domain = irq_domain_add_linear(NULL, AR2315_MISC_IRQ_COUNT,
+				       &ar2315_misc_irq_domain_ops, NULL);
+	if (!domain)
+		panic("Failed to add IRQ domain");
+
+	irq = irq_create_mapping(domain, AR2315_MISC_IRQ_AHB);
+	if (request_irq(irq, ar2315_ahb_err_handler, 0, "ar2315-ahb-error",
+			NULL))
+		pr_err("Failed to register ar2315-ahb-error interrupt\n");
+
+	irq_set_chained_handler_and_data(AR2315_IRQ_MISC,
+					 ar2315_misc_irq_handler, domain);
+
+	ar2315_misc_irq_domain = domain;
+}
+
+void __init ar2315_init_devices(void)
+{
+	/* Find board configuration */
+	ath25_find_config(AR2315_SPI_READ_BASE, AR2315_SPI_READ_SIZE);
+
+	ath25_add_wmac(0, AR2315_WLAN0_BASE, AR2315_IRQ_WLAN0);
+}
+
+static void ar2315_restart(char *command)
+{
+	void (*mips_reset_vec)(void) = (void *)0xbfc00000;
+
+	local_irq_disable();
+
+	/* try reset the system via reset control */
+	ar2315_rst_reg_write(AR2315_COLD_RESET, AR2317_RESET_SYSTEM);
+
+	/* Cold reset does not work on the AR2315/6, use the GPIO reset bits
+	 * a workaround. Give it some time to attempt a gpio based hardware
+	 * reset (atheros reference design workaround) */
+
+	/* TODO: implement the GPIO reset workaround */
+
+	/* Some boards (e.g. Senao EOC-2610) don't implement the reset logic
+	 * workaround. Attempt to jump to the mips reset location -
+	 * the boot loader itself might be able to recover the system */
+	mips_reset_vec();
+}
+
+/*
+ * This table is indexed by bits 5..4 of the CLOCKCTL1 register
+ * to determine the predevisor value.
+ */
+static int clockctl1_predivide_table[4] __initdata = { 1, 2, 4, 5 };
+static int pllc_divide_table[5] __initdata = { 2, 3, 4, 6, 3 };
+
+static unsigned __init ar2315_sys_clk(u32 clock_ctl)
+{
+	unsigned int pllc_ctrl, cpu_div;
+	unsigned int pllc_out, refdiv, fdiv, divby2;
+	unsigned int clk_div;
+
+	pllc_ctrl = ar2315_rst_reg_read(AR2315_PLLC_CTL);
+	refdiv = ATH25_REG_MS(pllc_ctrl, AR2315_PLLC_REF_DIV);
+	refdiv = clockctl1_predivide_table[refdiv];
+	fdiv = ATH25_REG_MS(pllc_ctrl, AR2315_PLLC_FDBACK_DIV);
+	divby2 = ATH25_REG_MS(pllc_ctrl, AR2315_PLLC_ADD_FDBACK_DIV) + 1;
+	pllc_out = (40000000 / refdiv) * (2 * divby2) * fdiv;
+
+	/* clkm input selected */
+	switch (clock_ctl & AR2315_CPUCLK_CLK_SEL_M) {
+	case 0:
+	case 1:
+		clk_div = ATH25_REG_MS(pllc_ctrl, AR2315_PLLC_CLKM_DIV);
+		clk_div = pllc_divide_table[clk_div];
+		break;
+	case 2:
+		clk_div = ATH25_REG_MS(pllc_ctrl, AR2315_PLLC_CLKC_DIV);
+		clk_div = pllc_divide_table[clk_div];
+		break;
+	default:
+		pllc_out = 40000000;
+		clk_div = 1;
+		break;
+	}
+
+	cpu_div = ATH25_REG_MS(clock_ctl, AR2315_CPUCLK_CLK_DIV);
+	cpu_div = cpu_div * 2 ?: 1;
+
+	return pllc_out / (clk_div * cpu_div);
+}
+
+static inline unsigned ar2315_cpu_frequency(void)
+{
+	return ar2315_sys_clk(ar2315_rst_reg_read(AR2315_CPUCLK));
+}
+
+static inline unsigned ar2315_apb_frequency(void)
+{
+	return ar2315_sys_clk(ar2315_rst_reg_read(AR2315_AMBACLK));
+}
+
+void __init ar2315_plat_time_init(void)
+{
+	mips_hpt_frequency = ar2315_cpu_frequency() / 2;
+}
+
+void __init ar2315_plat_mem_setup(void)
+{
+	void __iomem *sdram_base;
+	u32 memsize, memcfg;
+	u32 devid;
+	u32 config;
+
+	/* Detect memory size */
+	sdram_base = ioremap(AR2315_SDRAMCTL_BASE,
+				     AR2315_SDRAMCTL_SIZE);
+	memcfg = __raw_readl(sdram_base + AR2315_MEM_CFG);
+	memsize   = 1 + ATH25_REG_MS(memcfg, AR2315_MEM_CFG_DATA_WIDTH);
+	memsize <<= 1 + ATH25_REG_MS(memcfg, AR2315_MEM_CFG_COL_WIDTH);
+	memsize <<= 1 + ATH25_REG_MS(memcfg, AR2315_MEM_CFG_ROW_WIDTH);
+	memsize <<= 3;
+	memblock_add(0, memsize);
+	iounmap(sdram_base);
+
+	ar2315_rst_base = ioremap(AR2315_RST_BASE, AR2315_RST_SIZE);
+
+	/* Detect the hardware based on the device ID */
+	devid = ar2315_rst_reg_read(AR2315_SREV) & AR2315_REV_CHIP;
+	switch (devid) {
+	case 0x91:	/* Need to check */
+		ath25_soc = ATH25_SOC_AR2318;
+		break;
+	case 0x90:
+		ath25_soc = ATH25_SOC_AR2317;
+		break;
+	case 0x87:
+		ath25_soc = ATH25_SOC_AR2316;
+		break;
+	case 0x86:
+	default:
+		ath25_soc = ATH25_SOC_AR2315;
+		break;
+	}
+	ath25_board.devid = devid;
+
+	/* Clear any lingering AHB errors */
+	config = read_c0_config();
+	write_c0_config(config & ~0x3);
+	ar2315_rst_reg_write(AR2315_AHB_ERR0, AR2315_AHB_ERROR_DET);
+	ar2315_rst_reg_read(AR2315_AHB_ERR1);
+	ar2315_rst_reg_write(AR2315_WDT_CTRL, AR2315_WDT_CTRL_IGNORE);
+
+	_machine_restart = ar2315_restart;
+}
+
+#ifdef CONFIG_PCI_AR2315
+static struct resource ar2315_pci_res[] = {
+	{
+		.name = "ar2315-pci-ctrl",
+		.flags = IORESOURCE_MEM,
+		.start = AR2315_PCI_BASE,
+		.end = AR2315_PCI_BASE + AR2315_PCI_SIZE - 1,
+	},
+	{
+		.name = "ar2315-pci-ext",
+		.flags = IORESOURCE_MEM,
+		.start = AR2315_PCI_EXT_BASE,
+		.end = AR2315_PCI_EXT_BASE + AR2315_PCI_EXT_SIZE - 1,
+	},
+	{
+		.name = "ar2315-pci",
+		.flags = IORESOURCE_IRQ,
+		.start = AR2315_IRQ_LCBUS_PCI,
+		.end = AR2315_IRQ_LCBUS_PCI,
+	},
+};
+#endif
+
+void __init ar2315_arch_init(void)
+{
+	unsigned irq = irq_create_mapping(ar2315_misc_irq_domain,
+					  AR2315_MISC_IRQ_UART0);
+
+	ath25_serial_setup(AR2315_UART0_BASE, irq, ar2315_apb_frequency());
+
+#ifdef CONFIG_PCI_AR2315
+	if (ath25_soc == ATH25_SOC_AR2315) {
+		/* Reset PCI DMA logic */
+		ar2315_rst_reg_mask(AR2315_RESET, 0, AR2315_RESET_PCIDMA);
+		msleep(20);
+		ar2315_rst_reg_mask(AR2315_RESET, AR2315_RESET_PCIDMA, 0);
+		msleep(20);
+
+		/* Configure endians */
+		ar2315_rst_reg_mask(AR2315_ENDIAN_CTL, 0, AR2315_CONFIG_PCIAHB |
+				    AR2315_CONFIG_PCIAHB_BRIDGE);
+
+		/* Configure as PCI host with DMA */
+		ar2315_rst_reg_write(AR2315_PCICLK, AR2315_PCICLK_PLLC_CLKM |
+				  (AR2315_PCICLK_IN_FREQ_DIV_6 <<
+				   AR2315_PCICLK_DIV_S));
+		ar2315_rst_reg_mask(AR2315_AHB_ARB_CTL, 0, AR2315_ARB_PCI);
+		ar2315_rst_reg_mask(AR2315_IF_CTL, AR2315_IF_PCI_CLK_MASK |
+				    AR2315_IF_MASK, AR2315_IF_PCI |
+				    AR2315_IF_PCI_HOST | AR2315_IF_PCI_INTR |
+				    (AR2315_IF_PCI_CLK_OUTPUT_CLK <<
+				     AR2315_IF_PCI_CLK_SHIFT));
+
+		platform_device_register_simple("ar2315-pci", -1,
+						ar2315_pci_res,
+						ARRAY_SIZE(ar2315_pci_res));
+	}
+#endif
+}
diff --git a/arch/mips/ath25/ar2315.h b/arch/mips/ath25/ar2315.h
new file mode 100644
index 000000000..fccc64f6d
--- /dev/null
+++ b/arch/mips/ath25/ar2315.h
@@ -0,0 +1,23 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __AR2315_H
+#define __AR2315_H
+
+#ifdef CONFIG_SOC_AR2315
+
+void ar2315_arch_init_irq(void);
+void ar2315_init_devices(void);
+void ar2315_plat_time_init(void);
+void ar2315_plat_mem_setup(void);
+void ar2315_arch_init(void);
+
+#else
+
+static inline void ar2315_arch_init_irq(void) {}
+static inline void ar2315_init_devices(void) {}
+static inline void ar2315_plat_time_init(void) {}
+static inline void ar2315_plat_mem_setup(void) {}
+static inline void ar2315_arch_init(void) {}
+
+#endif
+
+#endif	/* __AR2315_H */
diff --git a/arch/mips/ath25/ar2315_regs.h b/arch/mips/ath25/ar2315_regs.h
new file mode 100644
index 000000000..16e86149c
--- /dev/null
+++ b/arch/mips/ath25/ar2315_regs.h
@@ -0,0 +1,410 @@
+/*
+ * Register definitions for AR2315+
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003 Atheros Communications, Inc.,  All Rights Reserved.
+ * Copyright (C) 2006 FON Technology, SL.
+ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
+ * Copyright (C) 2006-2008 Felix Fietkau <nbd@openwrt.org>
+ */
+
+#ifndef __ASM_MACH_ATH25_AR2315_REGS_H
+#define __ASM_MACH_ATH25_AR2315_REGS_H
+
+/*
+ * IRQs
+ */
+#define AR2315_IRQ_MISC		(MIPS_CPU_IRQ_BASE + 2)	/* C0_CAUSE: 0x0400 */
+#define AR2315_IRQ_WLAN0	(MIPS_CPU_IRQ_BASE + 3)	/* C0_CAUSE: 0x0800 */
+#define AR2315_IRQ_ENET0	(MIPS_CPU_IRQ_BASE + 4)	/* C0_CAUSE: 0x1000 */
+#define AR2315_IRQ_LCBUS_PCI	(MIPS_CPU_IRQ_BASE + 5)	/* C0_CAUSE: 0x2000 */
+#define AR2315_IRQ_WLAN0_POLL	(MIPS_CPU_IRQ_BASE + 6)	/* C0_CAUSE: 0x4000 */
+
+/*
+ * Miscellaneous interrupts, which share IP2.
+ */
+#define AR2315_MISC_IRQ_UART0		0
+#define AR2315_MISC_IRQ_I2C_RSVD	1
+#define AR2315_MISC_IRQ_SPI		2
+#define AR2315_MISC_IRQ_AHB		3
+#define AR2315_MISC_IRQ_APB		4
+#define AR2315_MISC_IRQ_TIMER		5
+#define AR2315_MISC_IRQ_GPIO		6
+#define AR2315_MISC_IRQ_WATCHDOG	7
+#define AR2315_MISC_IRQ_IR_RSVD		8
+#define AR2315_MISC_IRQ_COUNT		9
+
+/*
+ * Address map
+ */
+#define AR2315_SPI_READ_BASE	0x08000000	/* SPI flash */
+#define AR2315_SPI_READ_SIZE	0x01000000
+#define AR2315_WLAN0_BASE	0x10000000	/* Wireless MMR */
+#define AR2315_PCI_BASE		0x10100000	/* PCI MMR */
+#define AR2315_PCI_SIZE		0x00001000
+#define AR2315_SDRAMCTL_BASE	0x10300000	/* SDRAM MMR */
+#define AR2315_SDRAMCTL_SIZE	0x00000020
+#define AR2315_LOCAL_BASE	0x10400000	/* Local bus MMR */
+#define AR2315_ENET0_BASE	0x10500000	/* Ethernet MMR */
+#define AR2315_RST_BASE		0x11000000	/* Reset control MMR */
+#define AR2315_RST_SIZE		0x00000100
+#define AR2315_UART0_BASE	0x11100000	/* UART MMR */
+#define AR2315_SPI_MMR_BASE	0x11300000	/* SPI flash MMR */
+#define AR2315_SPI_MMR_SIZE	0x00000010
+#define AR2315_PCI_EXT_BASE	0x80000000	/* PCI external */
+#define AR2315_PCI_EXT_SIZE	0x40000000
+
+/*
+ * Configuration registers
+ */
+
+/* Cold reset register */
+#define AR2315_COLD_RESET		0x0000
+
+#define AR2315_RESET_COLD_AHB		0x00000001
+#define AR2315_RESET_COLD_APB		0x00000002
+#define AR2315_RESET_COLD_CPU		0x00000004
+#define AR2315_RESET_COLD_CPUWARM	0x00000008
+#define AR2315_RESET_SYSTEM		(RESET_COLD_CPU |\
+					 RESET_COLD_APB |\
+					 RESET_COLD_AHB)  /* full system */
+#define AR2317_RESET_SYSTEM		0x00000010
+
+/* Reset register */
+#define AR2315_RESET			0x0004
+
+#define AR2315_RESET_WARM_WLAN0_MAC	0x00000001  /* warm reset WLAN0 MAC */
+#define AR2315_RESET_WARM_WLAN0_BB	0x00000002  /* warm reset WLAN0 BB */
+#define AR2315_RESET_MPEGTS_RSVD	0x00000004  /* warm reset MPEG-TS */
+#define AR2315_RESET_PCIDMA		0x00000008  /* warm reset PCI ahb/dma */
+#define AR2315_RESET_MEMCTL		0x00000010  /* warm reset mem control */
+#define AR2315_RESET_LOCAL		0x00000020  /* warm reset local bus */
+#define AR2315_RESET_I2C_RSVD		0x00000040  /* warm reset I2C bus */
+#define AR2315_RESET_SPI		0x00000080  /* warm reset SPI iface */
+#define AR2315_RESET_UART0		0x00000100  /* warm reset UART0 */
+#define AR2315_RESET_IR_RSVD		0x00000200  /* warm reset IR iface */
+#define AR2315_RESET_EPHY0		0x00000400  /* cold reset ENET0 phy */
+#define AR2315_RESET_ENET0		0x00000800  /* cold reset ENET0 MAC */
+
+/* AHB master arbitration control */
+#define AR2315_AHB_ARB_CTL		0x0008
+
+#define AR2315_ARB_CPU			0x00000001  /* CPU, default */
+#define AR2315_ARB_WLAN			0x00000002  /* WLAN */
+#define AR2315_ARB_MPEGTS_RSVD		0x00000004  /* MPEG-TS */
+#define AR2315_ARB_LOCAL		0x00000008  /* Local bus */
+#define AR2315_ARB_PCI			0x00000010  /* PCI bus */
+#define AR2315_ARB_ETHERNET		0x00000020  /* Ethernet */
+#define AR2315_ARB_RETRY		0x00000100  /* Retry policy (debug) */
+
+/* Config Register */
+#define AR2315_ENDIAN_CTL		0x000c
+
+#define AR2315_CONFIG_AHB		0x00000001  /* EC-AHB bridge endian */
+#define AR2315_CONFIG_WLAN		0x00000002  /* WLAN byteswap */
+#define AR2315_CONFIG_MPEGTS_RSVD	0x00000004  /* MPEG-TS byteswap */
+#define AR2315_CONFIG_PCI		0x00000008  /* PCI byteswap */
+#define AR2315_CONFIG_MEMCTL		0x00000010  /* Mem controller endian */
+#define AR2315_CONFIG_LOCAL		0x00000020  /* Local bus byteswap */
+#define AR2315_CONFIG_ETHERNET		0x00000040  /* Ethernet byteswap */
+#define AR2315_CONFIG_MERGE		0x00000200  /* CPU write buffer merge */
+#define AR2315_CONFIG_CPU		0x00000400  /* CPU big endian */
+#define AR2315_CONFIG_BIG		0x00000400
+#define AR2315_CONFIG_PCIAHB		0x00000800
+#define AR2315_CONFIG_PCIAHB_BRIDGE	0x00001000
+#define AR2315_CONFIG_SPI		0x00008000  /* SPI byteswap */
+#define AR2315_CONFIG_CPU_DRAM		0x00010000
+#define AR2315_CONFIG_CPU_PCI		0x00020000
+#define AR2315_CONFIG_CPU_MMR		0x00040000
+
+/* NMI control */
+#define AR2315_NMI_CTL			0x0010
+
+#define AR2315_NMI_EN			1
+
+/* Revision Register - Initial value is 0x3010 (WMAC 3.0, AR231X 1.0). */
+#define AR2315_SREV			0x0014
+
+#define AR2315_REV_MAJ			0x000000f0
+#define AR2315_REV_MAJ_S		4
+#define AR2315_REV_MIN			0x0000000f
+#define AR2315_REV_MIN_S		0
+#define AR2315_REV_CHIP			(AR2315_REV_MAJ | AR2315_REV_MIN)
+
+/* Interface Enable */
+#define AR2315_IF_CTL			0x0018
+
+#define AR2315_IF_MASK			0x00000007
+#define AR2315_IF_DISABLED		0		/* Disable all */
+#define AR2315_IF_PCI			1		/* PCI */
+#define AR2315_IF_TS_LOCAL		2		/* Local bus */
+#define AR2315_IF_ALL			3		/* Emulation only */
+#define AR2315_IF_LOCAL_HOST		0x00000008
+#define AR2315_IF_PCI_HOST		0x00000010
+#define AR2315_IF_PCI_INTR		0x00000020
+#define AR2315_IF_PCI_CLK_MASK		0x00030000
+#define AR2315_IF_PCI_CLK_INPUT		0
+#define AR2315_IF_PCI_CLK_OUTPUT_LOW	1
+#define AR2315_IF_PCI_CLK_OUTPUT_CLK	2
+#define AR2315_IF_PCI_CLK_OUTPUT_HIGH	3
+#define AR2315_IF_PCI_CLK_SHIFT		16
+
+/* APB Interrupt control */
+#define AR2315_ISR			0x0020
+#define AR2315_IMR			0x0024
+#define AR2315_GISR			0x0028
+
+#define AR2315_ISR_UART0	0x00000001	/* high speed UART */
+#define AR2315_ISR_I2C_RSVD	0x00000002	/* I2C bus */
+#define AR2315_ISR_SPI		0x00000004	/* SPI bus */
+#define AR2315_ISR_AHB		0x00000008	/* AHB error */
+#define AR2315_ISR_APB		0x00000010	/* APB error */
+#define AR2315_ISR_TIMER	0x00000020	/* Timer */
+#define AR2315_ISR_GPIO		0x00000040	/* GPIO */
+#define AR2315_ISR_WD		0x00000080	/* Watchdog */
+#define AR2315_ISR_IR_RSVD	0x00000100	/* IR */
+
+#define AR2315_GISR_MISC	0x00000001	/* Misc */
+#define AR2315_GISR_WLAN0	0x00000002	/* WLAN0 */
+#define AR2315_GISR_MPEGTS_RSVD	0x00000004	/* MPEG-TS */
+#define AR2315_GISR_LOCALPCI	0x00000008	/* Local/PCI bus */
+#define AR2315_GISR_WMACPOLL	0x00000010
+#define AR2315_GISR_TIMER	0x00000020
+#define AR2315_GISR_ETHERNET	0x00000040	/* Ethernet */
+
+/* Generic timer */
+#define AR2315_TIMER			0x0030
+#define AR2315_RELOAD			0x0034
+
+/* Watchdog timer */
+#define AR2315_WDT_TIMER		0x0038
+#define AR2315_WDT_CTRL			0x003c
+
+#define AR2315_WDT_CTRL_IGNORE	0x00000000	/* ignore expiration */
+#define AR2315_WDT_CTRL_NMI	0x00000001	/* NMI on watchdog */
+#define AR2315_WDT_CTRL_RESET	0x00000002	/* reset on watchdog */
+
+/* CPU Performance Counters */
+#define AR2315_PERFCNT0			0x0048
+#define AR2315_PERFCNT1			0x004c
+
+#define AR2315_PERF0_DATAHIT	0x00000001  /* Count Data Cache Hits */
+#define AR2315_PERF0_DATAMISS	0x00000002  /* Count Data Cache Misses */
+#define AR2315_PERF0_INSTHIT	0x00000004  /* Count Instruction Cache Hits */
+#define AR2315_PERF0_INSTMISS	0x00000008  /* Count Instruction Cache Misses */
+#define AR2315_PERF0_ACTIVE	0x00000010  /* Count Active Processor Cycles */
+#define AR2315_PERF0_WBHIT	0x00000020  /* Count CPU Write Buffer Hits */
+#define AR2315_PERF0_WBMISS	0x00000040  /* Count CPU Write Buffer Misses */
+
+#define AR2315_PERF1_EB_ARDY	0x00000001  /* Count EB_ARdy signal */
+#define AR2315_PERF1_EB_AVALID	0x00000002  /* Count EB_AValid signal */
+#define AR2315_PERF1_EB_WDRDY	0x00000004  /* Count EB_WDRdy signal */
+#define AR2315_PERF1_EB_RDVAL	0x00000008  /* Count EB_RdVal signal */
+#define AR2315_PERF1_VRADDR	0x00000010  /* Count valid read address cycles*/
+#define AR2315_PERF1_VWADDR	0x00000020  /* Count valid write address cycl.*/
+#define AR2315_PERF1_VWDATA	0x00000040  /* Count valid write data cycles */
+
+/* AHB Error Reporting */
+#define AR2315_AHB_ERR0			0x0050  /* error  */
+#define AR2315_AHB_ERR1			0x0054  /* haddr  */
+#define AR2315_AHB_ERR2			0x0058  /* hwdata */
+#define AR2315_AHB_ERR3			0x005c  /* hrdata */
+#define AR2315_AHB_ERR4			0x0060  /* status */
+
+#define AR2315_AHB_ERROR_DET	1 /* AHB Error has been detected,          */
+				  /* write 1 to clear all bits in ERR0     */
+#define AR2315_AHB_ERROR_OVR	2 /* AHB Error overflow has been detected  */
+#define AR2315_AHB_ERROR_WDT	4 /* AHB Error due to wdt instead of hresp */
+
+#define AR2315_PROCERR_HMAST		0x0000000f
+#define AR2315_PROCERR_HMAST_DFLT	0
+#define AR2315_PROCERR_HMAST_WMAC	1
+#define AR2315_PROCERR_HMAST_ENET	2
+#define AR2315_PROCERR_HMAST_PCIENDPT	3
+#define AR2315_PROCERR_HMAST_LOCAL	4
+#define AR2315_PROCERR_HMAST_CPU	5
+#define AR2315_PROCERR_HMAST_PCITGT	6
+#define AR2315_PROCERR_HMAST_S		0
+#define AR2315_PROCERR_HWRITE		0x00000010
+#define AR2315_PROCERR_HSIZE		0x00000060
+#define AR2315_PROCERR_HSIZE_S		5
+#define AR2315_PROCERR_HTRANS		0x00000180
+#define AR2315_PROCERR_HTRANS_S		7
+#define AR2315_PROCERR_HBURST		0x00000e00
+#define AR2315_PROCERR_HBURST_S		9
+
+/* Clock Control */
+#define AR2315_PLLC_CTL			0x0064
+#define AR2315_PLLV_CTL			0x0068
+#define AR2315_CPUCLK			0x006c
+#define AR2315_AMBACLK			0x0070
+#define AR2315_SYNCCLK			0x0074
+#define AR2315_DSL_SLEEP_CTL		0x0080
+#define AR2315_DSL_SLEEP_DUR		0x0084
+
+/* PLLc Control fields */
+#define AR2315_PLLC_REF_DIV_M		0x00000003
+#define AR2315_PLLC_REF_DIV_S		0
+#define AR2315_PLLC_FDBACK_DIV_M	0x0000007c
+#define AR2315_PLLC_FDBACK_DIV_S	2
+#define AR2315_PLLC_ADD_FDBACK_DIV_M	0x00000080
+#define AR2315_PLLC_ADD_FDBACK_DIV_S	7
+#define AR2315_PLLC_CLKC_DIV_M		0x0001c000
+#define AR2315_PLLC_CLKC_DIV_S		14
+#define AR2315_PLLC_CLKM_DIV_M		0x00700000
+#define AR2315_PLLC_CLKM_DIV_S		20
+
+/* CPU CLK Control fields */
+#define AR2315_CPUCLK_CLK_SEL_M		0x00000003
+#define AR2315_CPUCLK_CLK_SEL_S		0
+#define AR2315_CPUCLK_CLK_DIV_M		0x0000000c
+#define AR2315_CPUCLK_CLK_DIV_S		2
+
+/* AMBA CLK Control fields */
+#define AR2315_AMBACLK_CLK_SEL_M	0x00000003
+#define AR2315_AMBACLK_CLK_SEL_S	0
+#define AR2315_AMBACLK_CLK_DIV_M	0x0000000c
+#define AR2315_AMBACLK_CLK_DIV_S	2
+
+/* PCI Clock Control */
+#define AR2315_PCICLK			0x00a4
+
+#define AR2315_PCICLK_INPUT_M		0x00000003
+#define AR2315_PCICLK_INPUT_S		0
+#define AR2315_PCICLK_PLLC_CLKM		0
+#define AR2315_PCICLK_PLLC_CLKM1	1
+#define AR2315_PCICLK_PLLC_CLKC		2
+#define AR2315_PCICLK_REF_CLK		3
+#define AR2315_PCICLK_DIV_M		0x0000000c
+#define AR2315_PCICLK_DIV_S		2
+#define AR2315_PCICLK_IN_FREQ		0
+#define AR2315_PCICLK_IN_FREQ_DIV_6	1
+#define AR2315_PCICLK_IN_FREQ_DIV_8	2
+#define AR2315_PCICLK_IN_FREQ_DIV_10	3
+
+/* Observation Control Register */
+#define AR2315_OCR			0x00b0
+
+#define AR2315_OCR_GPIO0_IRIN		0x00000040
+#define AR2315_OCR_GPIO1_IROUT		0x00000080
+#define AR2315_OCR_GPIO3_RXCLR		0x00000200
+
+/* General Clock Control */
+#define AR2315_MISCCLK			0x00b4
+
+#define AR2315_MISCCLK_PLLBYPASS_EN	0x00000001
+#define AR2315_MISCCLK_PROCREFCLK	0x00000002
+
+/*
+ * SDRAM Controller
+ *   - No read or write buffers are included.
+ */
+#define AR2315_MEM_CFG			0x0000
+#define AR2315_MEM_CTRL			0x000c
+#define AR2315_MEM_REF			0x0010
+
+#define AR2315_MEM_CFG_DATA_WIDTH_M	0x00006000
+#define AR2315_MEM_CFG_DATA_WIDTH_S	13
+#define AR2315_MEM_CFG_COL_WIDTH_M	0x00001e00
+#define AR2315_MEM_CFG_COL_WIDTH_S	9
+#define AR2315_MEM_CFG_ROW_WIDTH_M	0x000001e0
+#define AR2315_MEM_CFG_ROW_WIDTH_S	5
+#define AR2315_MEM_CFG_BANKADDR_BITS_M	0x00000018
+#define AR2315_MEM_CFG_BANKADDR_BITS_S	3
+
+/*
+ * Local Bus Interface Registers
+ */
+#define AR2315_LB_CONFIG		0x0000
+
+#define AR2315_LBCONF_OE	0x00000001	/* =1 OE is low-true */
+#define AR2315_LBCONF_CS0	0x00000002	/* =1 first CS is low-true */
+#define AR2315_LBCONF_CS1	0x00000004	/* =1 2nd CS is low-true */
+#define AR2315_LBCONF_RDY	0x00000008	/* =1 RDY is low-true */
+#define AR2315_LBCONF_WE	0x00000010	/* =1 Write En is low-true */
+#define AR2315_LBCONF_WAIT	0x00000020	/* =1 WAIT is low-true */
+#define AR2315_LBCONF_ADS	0x00000040	/* =1 Adr Strobe is low-true */
+#define AR2315_LBCONF_MOT	0x00000080	/* =0 Intel, =1 Motorola */
+#define AR2315_LBCONF_8CS	0x00000100	/* =1 8 bits CS, 0= 16bits */
+#define AR2315_LBCONF_8DS	0x00000200	/* =1 8 bits Data S, 0=16bits */
+#define AR2315_LBCONF_ADS_EN	0x00000400	/* =1 Enable ADS */
+#define AR2315_LBCONF_ADR_OE	0x00000800	/* =1 Adr cap on OE, WE or DS */
+#define AR2315_LBCONF_ADDT_MUX	0x00001000	/* =1 Adr and Data share bus */
+#define AR2315_LBCONF_DATA_OE	0x00002000	/* =1 Data cap on OE, WE, DS */
+#define AR2315_LBCONF_16DATA	0x00004000	/* =1 Data is 16 bits wide */
+#define AR2315_LBCONF_SWAPDT	0x00008000	/* =1 Byte swap data */
+#define AR2315_LBCONF_SYNC	0x00010000	/* =1 Bus synchronous to clk */
+#define AR2315_LBCONF_INT	0x00020000	/* =1 Intr is low true */
+#define AR2315_LBCONF_INT_CTR0	0x00000000	/* GND high-Z, Vdd is high-Z */
+#define AR2315_LBCONF_INT_CTR1	0x00040000	/* GND drive, Vdd is high-Z */
+#define AR2315_LBCONF_INT_CTR2	0x00080000	/* GND high-Z, Vdd drive */
+#define AR2315_LBCONF_INT_CTR3	0x000c0000	/* GND drive, Vdd drive */
+#define AR2315_LBCONF_RDY_WAIT	0x00100000	/* =1 RDY is negative of WAIT */
+#define AR2315_LBCONF_INT_PULSE	0x00200000	/* =1 Interrupt is a pulse */
+#define AR2315_LBCONF_ENABLE	0x00400000	/* =1 Falcon respond to LB */
+
+#define AR2315_LB_CLKSEL		0x0004
+
+#define AR2315_LBCLK_EXT	0x00000001	/* use external clk for lb */
+
+#define AR2315_LB_1MS			0x0008
+
+#define AR2315_LB1MS_MASK	0x0003ffff	/* # of AHB clk cycles in 1ms */
+
+#define AR2315_LB_MISCCFG		0x000c
+
+#define AR2315_LBM_TXD_EN	0x00000001	/* Enable TXD for fragments */
+#define AR2315_LBM_RX_INTEN	0x00000002	/* Enable LB ints on RX ready */
+#define AR2315_LBM_MBOXWR_INTEN	0x00000004	/* Enable LB ints on mbox wr */
+#define AR2315_LBM_MBOXRD_INTEN	0x00000008	/* Enable LB ints on mbox rd */
+#define AR2315_LMB_DESCSWAP_EN	0x00000010	/* Byte swap desc enable */
+#define AR2315_LBM_TIMEOUT_M	0x00ffff80
+#define AR2315_LBM_TIMEOUT_S	7
+#define AR2315_LBM_PORTMUX	0x07000000
+
+#define AR2315_LB_RXTSOFF		0x0010
+
+#define AR2315_LB_TX_CHAIN_EN		0x0100
+
+#define AR2315_LB_TXEN_0	0x00000001
+#define AR2315_LB_TXEN_1	0x00000002
+#define AR2315_LB_TXEN_2	0x00000004
+#define AR2315_LB_TXEN_3	0x00000008
+
+#define AR2315_LB_TX_CHAIN_DIS		0x0104
+#define AR2315_LB_TX_DESC_PTR		0x0200
+
+#define AR2315_LB_RX_CHAIN_EN		0x0400
+
+#define AR2315_LB_RXEN		0x00000001
+
+#define AR2315_LB_RX_CHAIN_DIS		0x0404
+#define AR2315_LB_RX_DESC_PTR		0x0408
+
+#define AR2315_LB_INT_STATUS		0x0500
+
+#define AR2315_LB_INT_TX_DESC		0x00000001
+#define AR2315_LB_INT_TX_OK		0x00000002
+#define AR2315_LB_INT_TX_ERR		0x00000004
+#define AR2315_LB_INT_TX_EOF		0x00000008
+#define AR2315_LB_INT_RX_DESC		0x00000010
+#define AR2315_LB_INT_RX_OK		0x00000020
+#define AR2315_LB_INT_RX_ERR		0x00000040
+#define AR2315_LB_INT_RX_EOF		0x00000080
+#define AR2315_LB_INT_TX_TRUNC		0x00000100
+#define AR2315_LB_INT_TX_STARVE		0x00000200
+#define AR2315_LB_INT_LB_TIMEOUT	0x00000400
+#define AR2315_LB_INT_LB_ERR		0x00000800
+#define AR2315_LB_INT_MBOX_WR		0x00001000
+#define AR2315_LB_INT_MBOX_RD		0x00002000
+
+/* Bit definitions for INT MASK are the same as INT_STATUS */
+#define AR2315_LB_INT_MASK		0x0504
+
+#define AR2315_LB_INT_EN		0x0508
+#define AR2315_LB_MBOX			0x0600
+
+#endif /* __ASM_MACH_ATH25_AR2315_REGS_H */
diff --git a/arch/mips/ath25/ar5312.c b/arch/mips/ath25/ar5312.c
new file mode 100644
index 000000000..cfa103518
--- /dev/null
+++ b/arch/mips/ath25/ar5312.c
@@ -0,0 +1,390 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003 Atheros Communications, Inc.,  All Rights Reserved.
+ * Copyright (C) 2006 FON Technology, SL.
+ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
+ * Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
+ * Copyright (C) 2012 Alexandros C. Couloumbis <alex@ozo.com>
+ */
+
+/*
+ * Platform devices for Atheros AR5312 SoCs
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/bitops.h>
+#include <linux/irqdomain.h>
+#include <linux/interrupt.h>
+#include <linux/memblock.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/physmap.h>
+#include <linux/reboot.h>
+#include <asm/bootinfo.h>
+#include <asm/reboot.h>
+#include <asm/time.h>
+
+#include <ath25_platform.h>
+
+#include "devices.h"
+#include "ar5312.h"
+#include "ar5312_regs.h"
+
+static void __iomem *ar5312_rst_base;
+static struct irq_domain *ar5312_misc_irq_domain;
+
+static inline u32 ar5312_rst_reg_read(u32 reg)
+{
+	return __raw_readl(ar5312_rst_base + reg);
+}
+
+static inline void ar5312_rst_reg_write(u32 reg, u32 val)
+{
+	__raw_writel(val, ar5312_rst_base + reg);
+}
+
+static inline void ar5312_rst_reg_mask(u32 reg, u32 mask, u32 val)
+{
+	u32 ret = ar5312_rst_reg_read(reg);
+
+	ret &= ~mask;
+	ret |= val;
+	ar5312_rst_reg_write(reg, ret);
+}
+
+static irqreturn_t ar5312_ahb_err_handler(int cpl, void *dev_id)
+{
+	u32 proc1 = ar5312_rst_reg_read(AR5312_PROC1);
+	u32 proc_addr = ar5312_rst_reg_read(AR5312_PROCADDR); /* clears error */
+	u32 dma1 = ar5312_rst_reg_read(AR5312_DMA1);
+	u32 dma_addr = ar5312_rst_reg_read(AR5312_DMAADDR);   /* clears error */
+
+	pr_emerg("AHB interrupt: PROCADDR=0x%8.8x PROC1=0x%8.8x DMAADDR=0x%8.8x DMA1=0x%8.8x\n",
+		 proc_addr, proc1, dma_addr, dma1);
+
+	machine_restart("AHB error"); /* Catastrophic failure */
+	return IRQ_HANDLED;
+}
+
+static void ar5312_misc_irq_handler(struct irq_desc *desc)
+{
+	u32 pending = ar5312_rst_reg_read(AR5312_ISR) &
+		      ar5312_rst_reg_read(AR5312_IMR);
+	unsigned nr;
+	int ret = 0;
+
+	if (pending) {
+		struct irq_domain *domain = irq_desc_get_handler_data(desc);
+
+		nr = __ffs(pending);
+
+		ret = generic_handle_domain_irq(domain, nr);
+		if (nr == AR5312_MISC_IRQ_TIMER)
+			ar5312_rst_reg_read(AR5312_TIMER);
+	}
+
+	if (!pending || ret)
+		spurious_interrupt();
+}
+
+/* Enable the specified AR5312_MISC_IRQ interrupt */
+static void ar5312_misc_irq_unmask(struct irq_data *d)
+{
+	ar5312_rst_reg_mask(AR5312_IMR, 0, BIT(d->hwirq));
+}
+
+/* Disable the specified AR5312_MISC_IRQ interrupt */
+static void ar5312_misc_irq_mask(struct irq_data *d)
+{
+	ar5312_rst_reg_mask(AR5312_IMR, BIT(d->hwirq), 0);
+	ar5312_rst_reg_read(AR5312_IMR); /* flush write buffer */
+}
+
+static struct irq_chip ar5312_misc_irq_chip = {
+	.name		= "ar5312-misc",
+	.irq_unmask	= ar5312_misc_irq_unmask,
+	.irq_mask	= ar5312_misc_irq_mask,
+};
+
+static int ar5312_misc_irq_map(struct irq_domain *d, unsigned irq,
+			       irq_hw_number_t hw)
+{
+	irq_set_chip_and_handler(irq, &ar5312_misc_irq_chip, handle_level_irq);
+	return 0;
+}
+
+static const struct irq_domain_ops ar5312_misc_irq_domain_ops = {
+	.map = ar5312_misc_irq_map,
+};
+
+static void ar5312_irq_dispatch(void)
+{
+	u32 pending = read_c0_status() & read_c0_cause();
+
+	if (pending & CAUSEF_IP2)
+		do_IRQ(AR5312_IRQ_WLAN0);
+	else if (pending & CAUSEF_IP5)
+		do_IRQ(AR5312_IRQ_WLAN1);
+	else if (pending & CAUSEF_IP6)
+		do_IRQ(AR5312_IRQ_MISC);
+	else if (pending & CAUSEF_IP7)
+		do_IRQ(ATH25_IRQ_CPU_CLOCK);
+	else
+		spurious_interrupt();
+}
+
+void __init ar5312_arch_init_irq(void)
+{
+	struct irq_domain *domain;
+	unsigned irq;
+
+	ath25_irq_dispatch = ar5312_irq_dispatch;
+
+	domain = irq_domain_add_linear(NULL, AR5312_MISC_IRQ_COUNT,
+				       &ar5312_misc_irq_domain_ops, NULL);
+	if (!domain)
+		panic("Failed to add IRQ domain");
+
+	irq = irq_create_mapping(domain, AR5312_MISC_IRQ_AHB_PROC);
+	if (request_irq(irq, ar5312_ahb_err_handler, 0, "ar5312-ahb-error",
+			NULL))
+		pr_err("Failed to register ar5312-ahb-error interrupt\n");
+
+	irq_set_chained_handler_and_data(AR5312_IRQ_MISC,
+					 ar5312_misc_irq_handler, domain);
+
+	ar5312_misc_irq_domain = domain;
+}
+
+static struct physmap_flash_data ar5312_flash_data = {
+	.width = 2,
+};
+
+static struct resource ar5312_flash_resource = {
+	.start = AR5312_FLASH_BASE,
+	.end = AR5312_FLASH_BASE + AR5312_FLASH_SIZE - 1,
+	.flags = IORESOURCE_MEM,
+};
+
+static struct platform_device ar5312_physmap_flash = {
+	.name = "physmap-flash",
+	.id = 0,
+	.dev.platform_data = &ar5312_flash_data,
+	.resource = &ar5312_flash_resource,
+	.num_resources = 1,
+};
+
+static void __init ar5312_flash_init(void)
+{
+	void __iomem *flashctl_base;
+	u32 ctl;
+
+	flashctl_base = ioremap(AR5312_FLASHCTL_BASE,
+					AR5312_FLASHCTL_SIZE);
+
+	ctl = __raw_readl(flashctl_base + AR5312_FLASHCTL0);
+	ctl &= AR5312_FLASHCTL_MW;
+
+	/* fixup flash width */
+	switch (ctl) {
+	case AR5312_FLASHCTL_MW16:
+		ar5312_flash_data.width = 2;
+		break;
+	case AR5312_FLASHCTL_MW8:
+	default:
+		ar5312_flash_data.width = 1;
+		break;
+	}
+
+	/*
+	 * Configure flash bank 0.
+	 * Assume 8M window size. Flash will be aliased if it's smaller
+	 */
+	ctl |= AR5312_FLASHCTL_E | AR5312_FLASHCTL_AC_8M | AR5312_FLASHCTL_RBLE;
+	ctl |= 0x01 << AR5312_FLASHCTL_IDCY_S;
+	ctl |= 0x07 << AR5312_FLASHCTL_WST1_S;
+	ctl |= 0x07 << AR5312_FLASHCTL_WST2_S;
+	__raw_writel(ctl, flashctl_base + AR5312_FLASHCTL0);
+
+	/* Disable other flash banks */
+	ctl = __raw_readl(flashctl_base + AR5312_FLASHCTL1);
+	ctl &= ~(AR5312_FLASHCTL_E | AR5312_FLASHCTL_AC);
+	__raw_writel(ctl, flashctl_base + AR5312_FLASHCTL1);
+	ctl = __raw_readl(flashctl_base + AR5312_FLASHCTL2);
+	ctl &= ~(AR5312_FLASHCTL_E | AR5312_FLASHCTL_AC);
+	__raw_writel(ctl, flashctl_base + AR5312_FLASHCTL2);
+
+	iounmap(flashctl_base);
+}
+
+void __init ar5312_init_devices(void)
+{
+	struct ath25_boarddata *config;
+
+	ar5312_flash_init();
+
+	/* Locate board/radio config data */
+	ath25_find_config(AR5312_FLASH_BASE, AR5312_FLASH_SIZE);
+	config = ath25_board.config;
+
+	/* AR2313 has CPU minor rev. 10 */
+	if ((current_cpu_data.processor_id & 0xff) == 0x0a)
+		ath25_soc = ATH25_SOC_AR2313;
+
+	/* AR2312 shares the same Silicon ID as AR5312 */
+	else if (config->flags & BD_ISCASPER)
+		ath25_soc = ATH25_SOC_AR2312;
+
+	/* Everything else is probably AR5312 or compatible */
+	else
+		ath25_soc = ATH25_SOC_AR5312;
+
+	platform_device_register(&ar5312_physmap_flash);
+
+	switch (ath25_soc) {
+	case ATH25_SOC_AR5312:
+		if (!ath25_board.radio)
+			return;
+
+		if (!(config->flags & BD_WLAN0))
+			break;
+
+		ath25_add_wmac(0, AR5312_WLAN0_BASE, AR5312_IRQ_WLAN0);
+		break;
+	case ATH25_SOC_AR2312:
+	case ATH25_SOC_AR2313:
+		if (!ath25_board.radio)
+			return;
+		break;
+	default:
+		break;
+	}
+
+	if (config->flags & BD_WLAN1)
+		ath25_add_wmac(1, AR5312_WLAN1_BASE, AR5312_IRQ_WLAN1);
+}
+
+static void ar5312_restart(char *command)
+{
+	/* reset the system */
+	local_irq_disable();
+	while (1)
+		ar5312_rst_reg_write(AR5312_RESET, AR5312_RESET_SYSTEM);
+}
+
+/*
+ * This table is indexed by bits 5..4 of the CLOCKCTL1 register
+ * to determine the predevisor value.
+ */
+static unsigned clockctl1_predivide_table[4] __initdata = { 1, 2, 4, 5 };
+
+static unsigned __init ar5312_cpu_frequency(void)
+{
+	u32 scratch, devid, clock_ctl1;
+	u32 predivide_mask, multiplier_mask, doubler_mask;
+	unsigned predivide_shift, multiplier_shift;
+	unsigned predivide_select, predivisor, multiplier;
+
+	/* Trust the bootrom's idea of cpu frequency. */
+	scratch = ar5312_rst_reg_read(AR5312_SCRATCH);
+	if (scratch)
+		return scratch;
+
+	devid = ar5312_rst_reg_read(AR5312_REV);
+	devid = (devid & AR5312_REV_MAJ) >> AR5312_REV_MAJ_S;
+	if (devid == AR5312_REV_MAJ_AR2313) {
+		predivide_mask = AR2313_CLOCKCTL1_PREDIVIDE_MASK;
+		predivide_shift = AR2313_CLOCKCTL1_PREDIVIDE_SHIFT;
+		multiplier_mask = AR2313_CLOCKCTL1_MULTIPLIER_MASK;
+		multiplier_shift = AR2313_CLOCKCTL1_MULTIPLIER_SHIFT;
+		doubler_mask = AR2313_CLOCKCTL1_DOUBLER_MASK;
+	} else { /* AR5312 and AR2312 */
+		predivide_mask = AR5312_CLOCKCTL1_PREDIVIDE_MASK;
+		predivide_shift = AR5312_CLOCKCTL1_PREDIVIDE_SHIFT;
+		multiplier_mask = AR5312_CLOCKCTL1_MULTIPLIER_MASK;
+		multiplier_shift = AR5312_CLOCKCTL1_MULTIPLIER_SHIFT;
+		doubler_mask = AR5312_CLOCKCTL1_DOUBLER_MASK;
+	}
+
+	/*
+	 * Clocking is derived from a fixed 40MHz input clock.
+	 *
+	 *  cpu_freq = input_clock * MULT (where MULT is PLL multiplier)
+	 *  sys_freq = cpu_freq / 4	  (used for APB clock, serial,
+	 *				   flash, Timer, Watchdog Timer)
+	 *
+	 *  cnt_freq = cpu_freq / 2	  (use for CPU count/compare)
+	 *
+	 * So, for example, with a PLL multiplier of 5, we have
+	 *
+	 *  cpu_freq = 200MHz
+	 *  sys_freq = 50MHz
+	 *  cnt_freq = 100MHz
+	 *
+	 * We compute the CPU frequency, based on PLL settings.
+	 */
+
+	clock_ctl1 = ar5312_rst_reg_read(AR5312_CLOCKCTL1);
+	predivide_select = (clock_ctl1 & predivide_mask) >> predivide_shift;
+	predivisor = clockctl1_predivide_table[predivide_select];
+	multiplier = (clock_ctl1 & multiplier_mask) >> multiplier_shift;
+
+	if (clock_ctl1 & doubler_mask)
+		multiplier <<= 1;
+
+	return (40000000 / predivisor) * multiplier;
+}
+
+static inline unsigned ar5312_sys_frequency(void)
+{
+	return ar5312_cpu_frequency() / 4;
+}
+
+void __init ar5312_plat_time_init(void)
+{
+	mips_hpt_frequency = ar5312_cpu_frequency() / 2;
+}
+
+void __init ar5312_plat_mem_setup(void)
+{
+	void __iomem *sdram_base;
+	u32 memsize, memcfg, bank0_ac, bank1_ac;
+	u32 devid;
+
+	/* Detect memory size */
+	sdram_base = ioremap(AR5312_SDRAMCTL_BASE,
+				     AR5312_SDRAMCTL_SIZE);
+	memcfg = __raw_readl(sdram_base + AR5312_MEM_CFG1);
+	bank0_ac = ATH25_REG_MS(memcfg, AR5312_MEM_CFG1_AC0);
+	bank1_ac = ATH25_REG_MS(memcfg, AR5312_MEM_CFG1_AC1);
+	memsize = (bank0_ac ? (1 << (bank0_ac + 1)) : 0) +
+		  (bank1_ac ? (1 << (bank1_ac + 1)) : 0);
+	memsize <<= 20;
+	memblock_add(0, memsize);
+	iounmap(sdram_base);
+
+	ar5312_rst_base = ioremap(AR5312_RST_BASE, AR5312_RST_SIZE);
+
+	devid = ar5312_rst_reg_read(AR5312_REV);
+	devid >>= AR5312_REV_WMAC_MIN_S;
+	devid &= AR5312_REV_CHIP;
+	ath25_board.devid = (u16)devid;
+
+	/* Clear any lingering AHB errors */
+	ar5312_rst_reg_read(AR5312_PROCADDR);
+	ar5312_rst_reg_read(AR5312_DMAADDR);
+	ar5312_rst_reg_write(AR5312_WDT_CTRL, AR5312_WDT_CTRL_IGNORE);
+
+	_machine_restart = ar5312_restart;
+}
+
+void __init ar5312_arch_init(void)
+{
+	unsigned irq = irq_create_mapping(ar5312_misc_irq_domain,
+					  AR5312_MISC_IRQ_UART0);
+
+	ath25_serial_setup(AR5312_UART0_BASE, irq, ar5312_sys_frequency());
+}
diff --git a/arch/mips/ath25/ar5312.h b/arch/mips/ath25/ar5312.h
new file mode 100644
index 000000000..67518a59a
--- /dev/null
+++ b/arch/mips/ath25/ar5312.h
@@ -0,0 +1,23 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __AR5312_H
+#define __AR5312_H
+
+#ifdef CONFIG_SOC_AR5312
+
+void ar5312_arch_init_irq(void);
+void ar5312_init_devices(void);
+void ar5312_plat_time_init(void);
+void ar5312_plat_mem_setup(void);
+void ar5312_arch_init(void);
+
+#else
+
+static inline void ar5312_arch_init_irq(void) {}
+static inline void ar5312_init_devices(void) {}
+static inline void ar5312_plat_time_init(void) {}
+static inline void ar5312_plat_mem_setup(void) {}
+static inline void ar5312_arch_init(void) {}
+
+#endif
+
+#endif	/* __AR5312_H */
diff --git a/arch/mips/ath25/ar5312_regs.h b/arch/mips/ath25/ar5312_regs.h
new file mode 100644
index 000000000..4b947f967
--- /dev/null
+++ b/arch/mips/ath25/ar5312_regs.h
@@ -0,0 +1,224 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003 Atheros Communications, Inc.,  All Rights Reserved.
+ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
+ * Copyright (C) 2006 Felix Fietkau <nbd@openwrt.org>
+ */
+
+#ifndef __ASM_MACH_ATH25_AR5312_REGS_H
+#define __ASM_MACH_ATH25_AR5312_REGS_H
+
+/*
+ * IRQs
+ */
+#define AR5312_IRQ_WLAN0	(MIPS_CPU_IRQ_BASE + 2)	/* C0_CAUSE: 0x0400 */
+#define AR5312_IRQ_ENET0	(MIPS_CPU_IRQ_BASE + 3)	/* C0_CAUSE: 0x0800 */
+#define AR5312_IRQ_ENET1	(MIPS_CPU_IRQ_BASE + 4)	/* C0_CAUSE: 0x1000 */
+#define AR5312_IRQ_WLAN1	(MIPS_CPU_IRQ_BASE + 5)	/* C0_CAUSE: 0x2000 */
+#define AR5312_IRQ_MISC		(MIPS_CPU_IRQ_BASE + 6)	/* C0_CAUSE: 0x4000 */
+
+/*
+ * Miscellaneous interrupts, which share IP6.
+ */
+#define AR5312_MISC_IRQ_TIMER		0
+#define AR5312_MISC_IRQ_AHB_PROC	1
+#define AR5312_MISC_IRQ_AHB_DMA		2
+#define AR5312_MISC_IRQ_GPIO		3
+#define AR5312_MISC_IRQ_UART0		4
+#define AR5312_MISC_IRQ_UART0_DMA	5
+#define AR5312_MISC_IRQ_WATCHDOG	6
+#define AR5312_MISC_IRQ_LOCAL		7
+#define AR5312_MISC_IRQ_SPI		8
+#define AR5312_MISC_IRQ_COUNT		9
+
+/*
+ * Address Map
+ *
+ * The AR5312 supports 2 enet MACS, even though many reference boards only
+ * actually use 1 of them (i.e. Only MAC 0 is actually connected to an enet
+ * PHY or PHY switch. The AR2312 supports 1 enet MAC.
+ */
+#define AR5312_WLAN0_BASE		0x18000000
+#define AR5312_ENET0_BASE		0x18100000
+#define AR5312_ENET1_BASE		0x18200000
+#define AR5312_SDRAMCTL_BASE		0x18300000
+#define AR5312_SDRAMCTL_SIZE		0x00000010
+#define AR5312_FLASHCTL_BASE		0x18400000
+#define AR5312_FLASHCTL_SIZE		0x00000010
+#define AR5312_WLAN1_BASE		0x18500000
+#define AR5312_UART0_BASE		0x1c000000	/* UART MMR */
+#define AR5312_GPIO_BASE		0x1c002000
+#define AR5312_GPIO_SIZE		0x00000010
+#define AR5312_RST_BASE			0x1c003000
+#define AR5312_RST_SIZE			0x00000100
+#define AR5312_FLASH_BASE		0x1e000000
+#define AR5312_FLASH_SIZE		0x00800000
+
+/*
+ * Need these defines to determine true number of ethernet MACs
+ */
+#define AR5312_AR5312_REV2	0x0052		/* AR5312 WMAC (AP31) */
+#define AR5312_AR5312_REV7	0x0057		/* AR5312 WMAC (AP30-040) */
+#define AR5312_AR2313_REV8	0x0058		/* AR2313 WMAC (AP43-030) */
+
+/* Reset/Timer Block Address Map */
+#define AR5312_TIMER		0x0000 /* countdown timer */
+#define AR5312_RELOAD		0x0004 /* timer reload value */
+#define AR5312_WDT_CTRL		0x0008 /* watchdog cntrl */
+#define AR5312_WDT_TIMER	0x000c /* watchdog timer */
+#define AR5312_ISR		0x0010 /* Intr Status Reg */
+#define AR5312_IMR		0x0014 /* Intr Mask Reg */
+#define AR5312_RESET		0x0020
+#define AR5312_CLOCKCTL1	0x0064
+#define AR5312_SCRATCH		0x006c
+#define AR5312_PROCADDR		0x0070
+#define AR5312_PROC1		0x0074
+#define AR5312_DMAADDR		0x0078
+#define AR5312_DMA1		0x007c
+#define AR5312_ENABLE		0x0080 /* interface enb */
+#define AR5312_REV		0x0090 /* revision */
+
+/* AR5312_WDT_CTRL register bit field definitions */
+#define AR5312_WDT_CTRL_IGNORE	0x00000000	/* ignore expiration */
+#define AR5312_WDT_CTRL_NMI	0x00000001
+#define AR5312_WDT_CTRL_RESET	0x00000002
+
+/* AR5312_ISR register bit field definitions */
+#define AR5312_ISR_TIMER	0x00000001
+#define AR5312_ISR_AHBPROC	0x00000002
+#define AR5312_ISR_AHBDMA	0x00000004
+#define AR5312_ISR_GPIO		0x00000008
+#define AR5312_ISR_UART0	0x00000010
+#define AR5312_ISR_UART0DMA	0x00000020
+#define AR5312_ISR_WD		0x00000040
+#define AR5312_ISR_LOCAL	0x00000080
+
+/* AR5312_RESET register bit field definitions */
+#define AR5312_RESET_SYSTEM		0x00000001  /* cold reset full system */
+#define AR5312_RESET_PROC		0x00000002  /* cold reset MIPS core */
+#define AR5312_RESET_WLAN0		0x00000004  /* cold reset WLAN MAC/BB */
+#define AR5312_RESET_EPHY0		0x00000008  /* cold reset ENET0 phy */
+#define AR5312_RESET_EPHY1		0x00000010  /* cold reset ENET1 phy */
+#define AR5312_RESET_ENET0		0x00000020  /* cold reset ENET0 MAC */
+#define AR5312_RESET_ENET1		0x00000040  /* cold reset ENET1 MAC */
+#define AR5312_RESET_UART0		0x00000100  /* cold reset UART0 */
+#define AR5312_RESET_WLAN1		0x00000200  /* cold reset WLAN MAC/BB */
+#define AR5312_RESET_APB		0x00000400  /* cold reset APB ar5312 */
+#define AR5312_RESET_WARM_PROC		0x00001000  /* warm reset MIPS core */
+#define AR5312_RESET_WARM_WLAN0_MAC	0x00002000  /* warm reset WLAN0 MAC */
+#define AR5312_RESET_WARM_WLAN0_BB	0x00004000  /* warm reset WLAN0 BB */
+#define AR5312_RESET_NMI		0x00010000  /* send an NMI to the CPU */
+#define AR5312_RESET_WARM_WLAN1_MAC	0x00020000  /* warm reset WLAN1 MAC */
+#define AR5312_RESET_WARM_WLAN1_BB	0x00040000  /* warm reset WLAN1 BB */
+#define AR5312_RESET_LOCAL_BUS		0x00080000  /* reset local bus */
+#define AR5312_RESET_WDOG		0x00100000  /* last reset was a wdt */
+
+#define AR5312_RESET_WMAC0_BITS		(AR5312_RESET_WLAN0 |\
+					 AR5312_RESET_WARM_WLAN0_MAC |\
+					 AR5312_RESET_WARM_WLAN0_BB)
+
+#define AR5312_RESET_WMAC1_BITS		(AR5312_RESET_WLAN1 |\
+					 AR5312_RESET_WARM_WLAN1_MAC |\
+					 AR5312_RESET_WARM_WLAN1_BB)
+
+/* AR5312_CLOCKCTL1 register bit field definitions */
+#define AR5312_CLOCKCTL1_PREDIVIDE_MASK		0x00000030
+#define AR5312_CLOCKCTL1_PREDIVIDE_SHIFT	4
+#define AR5312_CLOCKCTL1_MULTIPLIER_MASK	0x00001f00
+#define AR5312_CLOCKCTL1_MULTIPLIER_SHIFT	8
+#define AR5312_CLOCKCTL1_DOUBLER_MASK		0x00010000
+
+/* Valid for AR5312 and AR2312 */
+#define AR5312_CLOCKCTL1_PREDIVIDE_MASK		0x00000030
+#define AR5312_CLOCKCTL1_PREDIVIDE_SHIFT	4
+#define AR5312_CLOCKCTL1_MULTIPLIER_MASK	0x00001f00
+#define AR5312_CLOCKCTL1_MULTIPLIER_SHIFT	8
+#define AR5312_CLOCKCTL1_DOUBLER_MASK		0x00010000
+
+/* Valid for AR2313 */
+#define AR2313_CLOCKCTL1_PREDIVIDE_MASK		0x00003000
+#define AR2313_CLOCKCTL1_PREDIVIDE_SHIFT	12
+#define AR2313_CLOCKCTL1_MULTIPLIER_MASK	0x001f0000
+#define AR2313_CLOCKCTL1_MULTIPLIER_SHIFT	16
+#define AR2313_CLOCKCTL1_DOUBLER_MASK		0x00000000
+
+/* AR5312_ENABLE register bit field definitions */
+#define AR5312_ENABLE_WLAN0			0x00000001
+#define AR5312_ENABLE_ENET0			0x00000002
+#define AR5312_ENABLE_ENET1			0x00000004
+#define AR5312_ENABLE_UART_AND_WLAN1_PIO	0x00000008/* UART & WLAN1 PIO */
+#define AR5312_ENABLE_WLAN1_DMA			0x00000010/* WLAN1 DMAs */
+#define AR5312_ENABLE_WLAN1		(AR5312_ENABLE_UART_AND_WLAN1_PIO |\
+					 AR5312_ENABLE_WLAN1_DMA)
+
+/* AR5312_REV register bit field definitions */
+#define AR5312_REV_WMAC_MAJ	0x0000f000
+#define AR5312_REV_WMAC_MAJ_S	12
+#define AR5312_REV_WMAC_MIN	0x00000f00
+#define AR5312_REV_WMAC_MIN_S	8
+#define AR5312_REV_MAJ		0x000000f0
+#define AR5312_REV_MAJ_S	4
+#define AR5312_REV_MIN		0x0000000f
+#define AR5312_REV_MIN_S	0
+#define AR5312_REV_CHIP		(AR5312_REV_MAJ|AR5312_REV_MIN)
+
+/* Major revision numbers, bits 7..4 of Revision ID register */
+#define AR5312_REV_MAJ_AR5312		0x4
+#define AR5312_REV_MAJ_AR2313		0x5
+
+/* Minor revision numbers, bits 3..0 of Revision ID register */
+#define AR5312_REV_MIN_DUAL		0x0	/* Dual WLAN version */
+#define AR5312_REV_MIN_SINGLE		0x1	/* Single WLAN version */
+
+/*
+ * ARM Flash Controller -- 3 flash banks with either x8 or x16 devices
+ */
+#define AR5312_FLASHCTL0	0x0000
+#define AR5312_FLASHCTL1	0x0004
+#define AR5312_FLASHCTL2	0x0008
+
+/* AR5312_FLASHCTL register bit field definitions */
+#define AR5312_FLASHCTL_IDCY	0x0000000f	/* Idle cycle turnaround time */
+#define AR5312_FLASHCTL_IDCY_S	0
+#define AR5312_FLASHCTL_WST1	0x000003e0	/* Wait state 1 */
+#define AR5312_FLASHCTL_WST1_S	5
+#define AR5312_FLASHCTL_RBLE	0x00000400	/* Read byte lane enable */
+#define AR5312_FLASHCTL_WST2	0x0000f800	/* Wait state 2 */
+#define AR5312_FLASHCTL_WST2_S	11
+#define AR5312_FLASHCTL_AC	0x00070000	/* Flash addr check (added) */
+#define AR5312_FLASHCTL_AC_S	16
+#define AR5312_FLASHCTL_AC_128K	0x00000000
+#define AR5312_FLASHCTL_AC_256K	0x00010000
+#define AR5312_FLASHCTL_AC_512K	0x00020000
+#define AR5312_FLASHCTL_AC_1M	0x00030000
+#define AR5312_FLASHCTL_AC_2M	0x00040000
+#define AR5312_FLASHCTL_AC_4M	0x00050000
+#define AR5312_FLASHCTL_AC_8M	0x00060000
+#define AR5312_FLASHCTL_AC_RES	0x00070000	/* 16MB is not supported */
+#define AR5312_FLASHCTL_E	0x00080000	/* Flash bank enable (added) */
+#define AR5312_FLASHCTL_BUSERR	0x01000000	/* Bus transfer error flag */
+#define AR5312_FLASHCTL_WPERR	0x02000000	/* Write protect error flag */
+#define AR5312_FLASHCTL_WP	0x04000000	/* Write protect */
+#define AR5312_FLASHCTL_BM	0x08000000	/* Burst mode */
+#define AR5312_FLASHCTL_MW	0x30000000	/* Mem width */
+#define AR5312_FLASHCTL_MW8	0x00000000	/* Mem width x8 */
+#define AR5312_FLASHCTL_MW16	0x10000000	/* Mem width x16 */
+#define AR5312_FLASHCTL_MW32	0x20000000	/* Mem width x32 (not supp) */
+#define AR5312_FLASHCTL_ATNR	0x00000000	/* Access == no retry */
+#define AR5312_FLASHCTL_ATR	0x80000000	/* Access == retry every */
+#define AR5312_FLASHCTL_ATR4	0xc0000000	/* Access == retry every 4 */
+
+/*
+ * ARM SDRAM Controller -- just enough to determine memory size
+ */
+#define AR5312_MEM_CFG1		0x0004
+
+#define AR5312_MEM_CFG1_AC0_M	0x00000700	/* bank 0: SDRAM addr check */
+#define AR5312_MEM_CFG1_AC0_S	8
+#define AR5312_MEM_CFG1_AC1_M	0x00007000	/* bank 1: SDRAM addr check */
+#define AR5312_MEM_CFG1_AC1_S	12
+
+#endif	/* __ASM_MACH_ATH25_AR5312_REGS_H */
diff --git a/arch/mips/ath25/board.c b/arch/mips/ath25/board.c
new file mode 100644
index 000000000..cb99f9739
--- /dev/null
+++ b/arch/mips/ath25/board.c
@@ -0,0 +1,236 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003 Atheros Communications, Inc.,  All Rights Reserved.
+ * Copyright (C) 2006 FON Technology, SL.
+ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
+ * Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <asm/irq_cpu.h>
+#include <asm/reboot.h>
+#include <asm/bootinfo.h>
+#include <asm/time.h>
+
+#include <ath25_platform.h>
+#include "devices.h"
+#include "ar5312.h"
+#include "ar2315.h"
+
+void (*ath25_irq_dispatch)(void);
+
+static inline bool check_radio_magic(const void __iomem *addr)
+{
+	addr += 0x7a; /* offset for flash magic */
+	return (__raw_readb(addr) == 0x5a) && (__raw_readb(addr + 1) == 0xa5);
+}
+
+static inline bool check_notempty(const void __iomem *addr)
+{
+	return __raw_readl(addr) != 0xffffffff;
+}
+
+static inline bool check_board_data(const void __iomem *addr, bool broken)
+{
+	/* config magic found */
+	if (__raw_readl(addr) == ATH25_BD_MAGIC)
+		return true;
+
+	if (!broken)
+		return false;
+
+	/* broken board data detected, use radio data to find the
+	 * offset, user will fix this */
+
+	if (check_radio_magic(addr + 0x1000))
+		return true;
+	if (check_radio_magic(addr + 0xf8))
+		return true;
+
+	return false;
+}
+
+static const void __iomem * __init find_board_config(const void __iomem *limit,
+						     const bool broken)
+{
+	const void __iomem *addr;
+	const void __iomem *begin = limit - 0x1000;
+	const void __iomem *end = limit - 0x30000;
+
+	for (addr = begin; addr >= end; addr -= 0x1000)
+		if (check_board_data(addr, broken))
+			return addr;
+
+	return NULL;
+}
+
+static const void __iomem * __init find_radio_config(const void __iomem *limit,
+						     const void __iomem *bcfg)
+{
+	const void __iomem *rcfg, *begin, *end;
+
+	/*
+	 * Now find the start of Radio Configuration data, using heuristics:
+	 * Search forward from Board Configuration data by 0x1000 bytes
+	 * at a time until we find non-0xffffffff.
+	 */
+	begin = bcfg + 0x1000;
+	end = limit;
+	for (rcfg = begin; rcfg < end; rcfg += 0x1000)
+		if (check_notempty(rcfg) && check_radio_magic(rcfg))
+			return rcfg;
+
+	/* AR2316 relocates radio config to new location */
+	begin = bcfg + 0xf8;
+	end = limit - 0x1000 + 0xf8;
+	for (rcfg = begin; rcfg < end; rcfg += 0x1000)
+		if (check_notempty(rcfg) && check_radio_magic(rcfg))
+			return rcfg;
+
+	return NULL;
+}
+
+/*
+ * NB: Search region size could be larger than the actual flash size,
+ * but this shouldn't be a problem here, because the flash
+ * will simply be mapped multiple times.
+ */
+int __init ath25_find_config(phys_addr_t base, unsigned long size)
+{
+	const void __iomem *flash_base, *flash_limit;
+	struct ath25_boarddata *config;
+	unsigned int rcfg_size;
+	int broken_boarddata = 0;
+	const void __iomem *bcfg, *rcfg;
+	u8 *board_data;
+	u8 *radio_data;
+	u8 *mac_addr;
+	u32 offset;
+
+	flash_base = ioremap(base, size);
+	flash_limit = flash_base + size;
+
+	ath25_board.config = NULL;
+	ath25_board.radio = NULL;
+
+	/* Copy the board and radio data to RAM, because accessing the mapped
+	 * memory of the flash directly after booting is not safe */
+
+	/* Try to find valid board and radio data */
+	bcfg = find_board_config(flash_limit, false);
+
+	/* If that fails, try to at least find valid radio data */
+	if (!bcfg) {
+		bcfg = find_board_config(flash_limit, true);
+		broken_boarddata = 1;
+	}
+
+	if (!bcfg) {
+		pr_warn("WARNING: No board configuration data found!\n");
+		goto error;
+	}
+
+	board_data = kzalloc(BOARD_CONFIG_BUFSZ, GFP_KERNEL);
+	if (!board_data)
+		goto error;
+	ath25_board.config = (struct ath25_boarddata *)board_data;
+	memcpy_fromio(board_data, bcfg, 0x100);
+	if (broken_boarddata) {
+		pr_warn("WARNING: broken board data detected\n");
+		config = ath25_board.config;
+		if (is_zero_ether_addr(config->enet0_mac)) {
+			pr_info("Fixing up empty mac addresses\n");
+			config->reset_config_gpio = 0xffff;
+			config->sys_led_gpio = 0xffff;
+			eth_random_addr(config->wlan0_mac);
+			config->wlan0_mac[0] &= ~0x06;
+			eth_random_addr(config->enet0_mac);
+			eth_random_addr(config->enet1_mac);
+		}
+	}
+
+	/* Radio config starts 0x100 bytes after board config, regardless
+	 * of what the physical layout on the flash chip looks like */
+
+	rcfg = find_radio_config(flash_limit, bcfg);
+	if (!rcfg) {
+		pr_warn("WARNING: Could not find Radio Configuration data\n");
+		goto error;
+	}
+
+	radio_data = board_data + 0x100 + ((rcfg - bcfg) & 0xfff);
+	ath25_board.radio = radio_data;
+	offset = radio_data - board_data;
+	pr_info("Radio config found at offset 0x%x (0x%x)\n", rcfg - bcfg,
+		offset);
+	rcfg_size = BOARD_CONFIG_BUFSZ - offset;
+	memcpy_fromio(radio_data, rcfg, rcfg_size);
+
+	mac_addr = &radio_data[0x1d * 2];
+	if (is_broadcast_ether_addr(mac_addr)) {
+		pr_info("Radio MAC is blank; using board-data\n");
+		ether_addr_copy(mac_addr, ath25_board.config->wlan0_mac);
+	}
+
+	iounmap(flash_base);
+
+	return 0;
+
+error:
+	iounmap(flash_base);
+	return -ENODEV;
+}
+
+static void ath25_halt(void)
+{
+	local_irq_disable();
+	unreachable();
+}
+
+void __init plat_mem_setup(void)
+{
+	_machine_halt = ath25_halt;
+	pm_power_off = ath25_halt;
+
+	if (is_ar5312())
+		ar5312_plat_mem_setup();
+	else
+		ar2315_plat_mem_setup();
+
+	/* Disable data watchpoints */
+	write_c0_watchlo0(0);
+}
+
+asmlinkage void plat_irq_dispatch(void)
+{
+	ath25_irq_dispatch();
+}
+
+void __init plat_time_init(void)
+{
+	if (is_ar5312())
+		ar5312_plat_time_init();
+	else
+		ar2315_plat_time_init();
+}
+
+unsigned int get_c0_compare_int(void)
+{
+	return CP0_LEGACY_COMPARE_IRQ;
+}
+
+void __init arch_init_irq(void)
+{
+	clear_c0_status(ST0_IM);
+	mips_cpu_irq_init();
+
+	/* Initialize interrupt controllers */
+	if (is_ar5312())
+		ar5312_arch_init_irq();
+	else
+		ar2315_arch_init_irq();
+}
diff --git a/arch/mips/ath25/devices.c b/arch/mips/ath25/devices.c
new file mode 100644
index 000000000..301a90282
--- /dev/null
+++ b/arch/mips/ath25/devices.c
@@ -0,0 +1,128 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/serial_8250.h>
+#include <linux/platform_device.h>
+#include <asm/bootinfo.h>
+
+#include <ath25_platform.h>
+#include "devices.h"
+#include "ar5312.h"
+#include "ar2315.h"
+
+struct ar231x_board_config ath25_board;
+enum ath25_soc_type ath25_soc = ATH25_SOC_UNKNOWN;
+
+static struct resource ath25_wmac0_res[] = {
+	{
+		.name = "wmac0_membase",
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.name = "wmac0_irq",
+		.flags = IORESOURCE_IRQ,
+	}
+};
+
+static struct resource ath25_wmac1_res[] = {
+	{
+		.name = "wmac1_membase",
+		.flags = IORESOURCE_MEM,
+	},
+	{
+		.name = "wmac1_irq",
+		.flags = IORESOURCE_IRQ,
+	}
+};
+
+static struct platform_device ath25_wmac[] = {
+	{
+		.id = 0,
+		.name = "ar231x-wmac",
+		.resource = ath25_wmac0_res,
+		.num_resources = ARRAY_SIZE(ath25_wmac0_res),
+		.dev.platform_data = &ath25_board,
+	},
+	{
+		.id = 1,
+		.name = "ar231x-wmac",
+		.resource = ath25_wmac1_res,
+		.num_resources = ARRAY_SIZE(ath25_wmac1_res),
+		.dev.platform_data = &ath25_board,
+	},
+};
+
+static const char * const soc_type_strings[] = {
+	[ATH25_SOC_AR5312] = "Atheros AR5312",
+	[ATH25_SOC_AR2312] = "Atheros AR2312",
+	[ATH25_SOC_AR2313] = "Atheros AR2313",
+	[ATH25_SOC_AR2315] = "Atheros AR2315",
+	[ATH25_SOC_AR2316] = "Atheros AR2316",
+	[ATH25_SOC_AR2317] = "Atheros AR2317",
+	[ATH25_SOC_AR2318] = "Atheros AR2318",
+	[ATH25_SOC_UNKNOWN] = "Atheros (unknown)",
+};
+
+const char *get_system_type(void)
+{
+	if ((ath25_soc >= ARRAY_SIZE(soc_type_strings)) ||
+	    !soc_type_strings[ath25_soc])
+		return soc_type_strings[ATH25_SOC_UNKNOWN];
+	return soc_type_strings[ath25_soc];
+}
+
+void __init ath25_serial_setup(u32 mapbase, int irq, unsigned int uartclk)
+{
+#ifdef CONFIG_SERIAL_8250_CONSOLE
+	struct uart_port s;
+
+	memset(&s, 0, sizeof(s));
+
+	s.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_IOREMAP;
+	s.iotype = UPIO_MEM32;
+	s.irq = irq;
+	s.regshift = 2;
+	s.mapbase = mapbase;
+	s.uartclk = uartclk;
+
+	early_serial_setup(&s);
+#endif /* CONFIG_SERIAL_8250_CONSOLE */
+}
+
+int __init ath25_add_wmac(int nr, u32 base, int irq)
+{
+	struct resource *res;
+
+	ath25_wmac[nr].dev.platform_data = &ath25_board;
+	res = &ath25_wmac[nr].resource[0];
+	res->start = base;
+	res->end = base + 0x10000 - 1;
+	res++;
+	res->start = irq;
+	res->end = irq;
+	return platform_device_register(&ath25_wmac[nr]);
+}
+
+static int __init ath25_register_devices(void)
+{
+	if (is_ar5312())
+		ar5312_init_devices();
+	else
+		ar2315_init_devices();
+
+	return 0;
+}
+
+device_initcall(ath25_register_devices);
+
+static int __init ath25_arch_init(void)
+{
+	if (is_ar5312())
+		ar5312_arch_init();
+	else
+		ar2315_arch_init();
+
+	return 0;
+}
+
+arch_initcall(ath25_arch_init);
diff --git a/arch/mips/ath25/devices.h b/arch/mips/ath25/devices.h
new file mode 100644
index 000000000..44cf69063
--- /dev/null
+++ b/arch/mips/ath25/devices.h
@@ -0,0 +1,44 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ATH25_DEVICES_H
+#define __ATH25_DEVICES_H
+
+#include <linux/cpu.h>
+
+#define ATH25_REG_MS(_val, _field)	(((_val) & _field##_M) >> _field##_S)
+
+#define ATH25_IRQ_CPU_CLOCK	(MIPS_CPU_IRQ_BASE + 7)	/* C0_CAUSE: 0x8000 */
+
+enum ath25_soc_type {
+	/* handled by ar5312.c */
+	ATH25_SOC_AR2312,
+	ATH25_SOC_AR2313,
+	ATH25_SOC_AR5312,
+
+	/* handled by ar2315.c */
+	ATH25_SOC_AR2315,
+	ATH25_SOC_AR2316,
+	ATH25_SOC_AR2317,
+	ATH25_SOC_AR2318,
+
+	ATH25_SOC_UNKNOWN
+};
+
+extern enum ath25_soc_type ath25_soc;
+extern struct ar231x_board_config ath25_board;
+extern void (*ath25_irq_dispatch)(void);
+
+int ath25_find_config(phys_addr_t offset, unsigned long size);
+void ath25_serial_setup(u32 mapbase, int irq, unsigned int uartclk);
+int ath25_add_wmac(int nr, u32 base, int irq);
+
+static inline bool is_ar2315(void)
+{
+	return (current_cpu_data.cputype == CPU_4KEC);
+}
+
+static inline bool is_ar5312(void)
+{
+	return !is_ar2315();
+}
+
+#endif
diff --git a/arch/mips/ath25/early_printk.c b/arch/mips/ath25/early_printk.c
new file mode 100644
index 000000000..d534761e9
--- /dev/null
+++ b/arch/mips/ath25/early_printk.c
@@ -0,0 +1,45 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2010 Gabor Juhos <juhosg@openwrt.org>
+ */
+
+#include <linux/mm.h>
+#include <linux/io.h>
+#include <linux/serial_reg.h>
+#include <asm/setup.h>
+
+#include "devices.h"
+#include "ar2315_regs.h"
+#include "ar5312_regs.h"
+
+static inline void prom_uart_wr(void __iomem *base, unsigned reg,
+				unsigned char ch)
+{
+	__raw_writel(ch, base + 4 * reg);
+}
+
+static inline unsigned char prom_uart_rr(void __iomem *base, unsigned reg)
+{
+	return __raw_readl(base + 4 * reg);
+}
+
+void prom_putchar(char ch)
+{
+	static void __iomem *base;
+
+	if (unlikely(base == NULL)) {
+		if (is_ar2315())
+			base = (void __iomem *)(KSEG1ADDR(AR2315_UART0_BASE));
+		else
+			base = (void __iomem *)(KSEG1ADDR(AR5312_UART0_BASE));
+	}
+
+	while ((prom_uart_rr(base, UART_LSR) & UART_LSR_THRE) == 0)
+		;
+	prom_uart_wr(base, UART_TX, (unsigned char)ch);
+	while ((prom_uart_rr(base, UART_LSR) & UART_LSR_THRE) == 0)
+		;
+}
diff --git a/arch/mips/ath25/prom.c b/arch/mips/ath25/prom.c
new file mode 100644
index 000000000..4466e14fe
--- /dev/null
+++ b/arch/mips/ath25/prom.c
@@ -0,0 +1,22 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright MontaVista Software Inc
+ * Copyright (C) 2003 Atheros Communications, Inc.,  All Rights Reserved.
+ * Copyright (C) 2006 FON Technology, SL.
+ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
+ * Copyright (C) 2006 Felix Fietkau <nbd@openwrt.org>
+ */
+
+/*
+ * Prom setup file for AR5312/AR231x SoCs
+ */
+
+#include <linux/init.h>
+#include <asm/bootinfo.h>
+
+void __init prom_init(void)
+{
+}
diff --git a/arch/mips/ath79/Kconfig b/arch/mips/ath79/Kconfig
new file mode 100644
index 000000000..736741664
--- /dev/null
+++ b/arch/mips/ath79/Kconfig
@@ -0,0 +1,48 @@
+# SPDX-License-Identifier: GPL-2.0
+if ATH79
+
+config SOC_AR71XX
+	select HAVE_PCI
+	def_bool n
+
+config SOC_AR724X
+	select HAVE_PCI
+	select PCI_AR724X if PCI
+	def_bool n
+
+config SOC_AR913X
+	def_bool n
+
+config SOC_AR933X
+	def_bool n
+
+config SOC_AR934X
+	select HAVE_PCI
+	select PCI_AR724X if PCI
+	def_bool n
+
+config SOC_QCA955X
+	select HAVE_PCI
+	select PCI_AR724X if PCI
+	def_bool n
+
+config PCI_AR724X
+	def_bool n
+
+config ATH79_DEV_GPIO_BUTTONS
+	def_bool n
+
+config ATH79_DEV_LEDS_GPIO
+	def_bool n
+
+config ATH79_DEV_SPI
+	def_bool n
+
+config ATH79_DEV_USB
+	def_bool n
+
+config ATH79_DEV_WMAC
+	depends on (SOC_AR913X || SOC_AR933X || SOC_AR934X || SOC_QCA955X)
+	def_bool n
+
+endif
diff --git a/arch/mips/ath79/Makefile b/arch/mips/ath79/Makefile
new file mode 100644
index 000000000..0fb3aaf42
--- /dev/null
+++ b/arch/mips/ath79/Makefile
@@ -0,0 +1,11 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Makefile for the Atheros AR71XX/AR724X/AR913X specific parts of the kernel
+#
+# Copyright (C) 2008-2011 Gabor Juhos <juhosg@openwrt.org>
+# Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+#
+
+obj-y	:= prom.o setup.o common.o clock.o
+
+obj-$(CONFIG_EARLY_PRINTK)		+= early_printk.o
diff --git a/arch/mips/ath79/Platform b/arch/mips/ath79/Platform
new file mode 100644
index 000000000..57744472e
--- /dev/null
+++ b/arch/mips/ath79/Platform
@@ -0,0 +1,6 @@
+#
+# Atheros AR71xx/AR724x/AR913x
+#
+
+cflags-$(CONFIG_ATH79)		+= -I$(srctree)/arch/mips/include/asm/mach-ath79
+load-$(CONFIG_ATH79)		= 0xffffffff80060000
diff --git a/arch/mips/ath79/clock.c b/arch/mips/ath79/clock.c
new file mode 100644
index 000000000..050f6553f
--- /dev/null
+++ b/arch/mips/ath79/clock.c
@@ -0,0 +1,673 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *  Atheros AR71XX/AR724X/AR913X common routines
+ *
+ *  Copyright (C) 2010-2011 Jaiganesh Narayanan <jnarayanan@atheros.com>
+ *  Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
+ *
+ *  Parts of this file are based on Atheros' 2.6.15/2.6.31 BSP
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+#include <linux/clkdev.h>
+#include <linux/clk-provider.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <dt-bindings/clock/ath79-clk.h>
+
+#include <asm/div64.h>
+
+#include <asm/mach-ath79/ath79.h>
+#include <asm/mach-ath79/ar71xx_regs.h>
+#include "common.h"
+
+#define AR71XX_BASE_FREQ	40000000
+#define AR724X_BASE_FREQ	40000000
+
+static struct clk *clks[ATH79_CLK_END];
+static struct clk_onecell_data clk_data = {
+	.clks = clks,
+	.clk_num = ARRAY_SIZE(clks),
+};
+
+static const char * const clk_names[ATH79_CLK_END] = {
+	[ATH79_CLK_CPU] = "cpu",
+	[ATH79_CLK_DDR] = "ddr",
+	[ATH79_CLK_AHB] = "ahb",
+	[ATH79_CLK_REF] = "ref",
+	[ATH79_CLK_MDIO] = "mdio",
+};
+
+static const char * __init ath79_clk_name(int type)
+{
+	BUG_ON(type >= ARRAY_SIZE(clk_names) || !clk_names[type]);
+	return clk_names[type];
+}
+
+static void __init __ath79_set_clk(int type, const char *name, struct clk *clk)
+{
+	if (IS_ERR(clk))
+		panic("failed to allocate %s clock structure", clk_names[type]);
+
+	clks[type] = clk;
+	clk_register_clkdev(clk, name, NULL);
+}
+
+static struct clk * __init ath79_set_clk(int type, unsigned long rate)
+{
+	const char *name = ath79_clk_name(type);
+	struct clk *clk;
+
+	clk = clk_register_fixed_rate(NULL, name, NULL, 0, rate);
+	__ath79_set_clk(type, name, clk);
+	return clk;
+}
+
+static struct clk * __init ath79_set_ff_clk(int type, const char *parent,
+					    unsigned int mult, unsigned int div)
+{
+	const char *name = ath79_clk_name(type);
+	struct clk *clk;
+
+	clk = clk_register_fixed_factor(NULL, name, parent, 0, mult, div);
+	__ath79_set_clk(type, name, clk);
+	return clk;
+}
+
+static unsigned long __init ath79_setup_ref_clk(unsigned long rate)
+{
+	struct clk *clk = clks[ATH79_CLK_REF];
+
+	if (clk)
+		rate = clk_get_rate(clk);
+	else
+		clk = ath79_set_clk(ATH79_CLK_REF, rate);
+
+	return rate;
+}
+
+static void __init ar71xx_clocks_init(void __iomem *pll_base)
+{
+	unsigned long ref_rate;
+	unsigned long cpu_rate;
+	unsigned long ddr_rate;
+	unsigned long ahb_rate;
+	u32 pll;
+	u32 freq;
+	u32 div;
+
+	ref_rate = ath79_setup_ref_clk(AR71XX_BASE_FREQ);
+
+	pll = __raw_readl(pll_base + AR71XX_PLL_REG_CPU_CONFIG);
+
+	div = ((pll >> AR71XX_PLL_FB_SHIFT) & AR71XX_PLL_FB_MASK) + 1;
+	freq = div * ref_rate;
+
+	div = ((pll >> AR71XX_CPU_DIV_SHIFT) & AR71XX_CPU_DIV_MASK) + 1;
+	cpu_rate = freq / div;
+
+	div = ((pll >> AR71XX_DDR_DIV_SHIFT) & AR71XX_DDR_DIV_MASK) + 1;
+	ddr_rate = freq / div;
+
+	div = (((pll >> AR71XX_AHB_DIV_SHIFT) & AR71XX_AHB_DIV_MASK) + 1) * 2;
+	ahb_rate = cpu_rate / div;
+
+	ath79_set_clk(ATH79_CLK_CPU, cpu_rate);
+	ath79_set_clk(ATH79_CLK_DDR, ddr_rate);
+	ath79_set_clk(ATH79_CLK_AHB, ahb_rate);
+}
+
+static void __init ar724x_clocks_init(void __iomem *pll_base)
+{
+	u32 mult, div, ddr_div, ahb_div;
+	u32 pll;
+
+	ath79_setup_ref_clk(AR71XX_BASE_FREQ);
+
+	pll = __raw_readl(pll_base + AR724X_PLL_REG_CPU_CONFIG);
+
+	mult = ((pll >> AR724X_PLL_FB_SHIFT) & AR724X_PLL_FB_MASK);
+	div = ((pll >> AR724X_PLL_REF_DIV_SHIFT) & AR724X_PLL_REF_DIV_MASK) * 2;
+
+	ddr_div = ((pll >> AR724X_DDR_DIV_SHIFT) & AR724X_DDR_DIV_MASK) + 1;
+	ahb_div = (((pll >> AR724X_AHB_DIV_SHIFT) & AR724X_AHB_DIV_MASK) + 1) * 2;
+
+	ath79_set_ff_clk(ATH79_CLK_CPU, "ref", mult, div);
+	ath79_set_ff_clk(ATH79_CLK_DDR, "ref", mult, div * ddr_div);
+	ath79_set_ff_clk(ATH79_CLK_AHB, "ref", mult, div * ahb_div);
+}
+
+static void __init ar933x_clocks_init(void __iomem *pll_base)
+{
+	unsigned long ref_rate;
+	u32 clock_ctrl;
+	u32 ref_div;
+	u32 ninit_mul;
+	u32 out_div;
+
+	u32 cpu_div;
+	u32 ddr_div;
+	u32 ahb_div;
+	u32 t;
+
+	t = ath79_reset_rr(AR933X_RESET_REG_BOOTSTRAP);
+	if (t & AR933X_BOOTSTRAP_REF_CLK_40)
+		ref_rate = (40 * 1000 * 1000);
+	else
+		ref_rate = (25 * 1000 * 1000);
+
+	ath79_setup_ref_clk(ref_rate);
+
+	clock_ctrl = __raw_readl(pll_base + AR933X_PLL_CLOCK_CTRL_REG);
+	if (clock_ctrl & AR933X_PLL_CLOCK_CTRL_BYPASS) {
+		ref_div = 1;
+		ninit_mul = 1;
+		out_div = 1;
+
+		cpu_div = 1;
+		ddr_div = 1;
+		ahb_div = 1;
+	} else {
+		u32 cpu_config;
+		u32 t;
+
+		cpu_config = __raw_readl(pll_base + AR933X_PLL_CPU_CONFIG_REG);
+
+		t = (cpu_config >> AR933X_PLL_CPU_CONFIG_REFDIV_SHIFT) &
+		    AR933X_PLL_CPU_CONFIG_REFDIV_MASK;
+		ref_div = t;
+
+		ninit_mul = (cpu_config >> AR933X_PLL_CPU_CONFIG_NINT_SHIFT) &
+		    AR933X_PLL_CPU_CONFIG_NINT_MASK;
+
+		t = (cpu_config >> AR933X_PLL_CPU_CONFIG_OUTDIV_SHIFT) &
+		    AR933X_PLL_CPU_CONFIG_OUTDIV_MASK;
+		if (t == 0)
+			t = 1;
+
+		out_div = (1 << t);
+
+		cpu_div = ((clock_ctrl >> AR933X_PLL_CLOCK_CTRL_CPU_DIV_SHIFT) &
+		     AR933X_PLL_CLOCK_CTRL_CPU_DIV_MASK) + 1;
+
+		ddr_div = ((clock_ctrl >> AR933X_PLL_CLOCK_CTRL_DDR_DIV_SHIFT) &
+		      AR933X_PLL_CLOCK_CTRL_DDR_DIV_MASK) + 1;
+
+		ahb_div = ((clock_ctrl >> AR933X_PLL_CLOCK_CTRL_AHB_DIV_SHIFT) &
+		     AR933X_PLL_CLOCK_CTRL_AHB_DIV_MASK) + 1;
+	}
+
+	ath79_set_ff_clk(ATH79_CLK_CPU, "ref", ninit_mul,
+			 ref_div * out_div * cpu_div);
+	ath79_set_ff_clk(ATH79_CLK_DDR, "ref", ninit_mul,
+			 ref_div * out_div * ddr_div);
+	ath79_set_ff_clk(ATH79_CLK_AHB, "ref", ninit_mul,
+			 ref_div * out_div * ahb_div);
+}
+
+static u32 __init ar934x_get_pll_freq(u32 ref, u32 ref_div, u32 nint, u32 nfrac,
+				      u32 frac, u32 out_div)
+{
+	u64 t;
+	u32 ret;
+
+	t = ref;
+	t *= nint;
+	do_div(t, ref_div);
+	ret = t;
+
+	t = ref;
+	t *= nfrac;
+	do_div(t, ref_div * frac);
+	ret += t;
+
+	ret /= (1 << out_div);
+	return ret;
+}
+
+static void __init ar934x_clocks_init(void __iomem *pll_base)
+{
+	unsigned long ref_rate;
+	unsigned long cpu_rate;
+	unsigned long ddr_rate;
+	unsigned long ahb_rate;
+	u32 pll, out_div, ref_div, nint, nfrac, frac, clk_ctrl, postdiv;
+	u32 cpu_pll, ddr_pll;
+	u32 bootstrap;
+	void __iomem *dpll_base;
+
+	dpll_base = ioremap(AR934X_SRIF_BASE, AR934X_SRIF_SIZE);
+
+	bootstrap = ath79_reset_rr(AR934X_RESET_REG_BOOTSTRAP);
+	if (bootstrap & AR934X_BOOTSTRAP_REF_CLK_40)
+		ref_rate = 40 * 1000 * 1000;
+	else
+		ref_rate = 25 * 1000 * 1000;
+
+	ref_rate = ath79_setup_ref_clk(ref_rate);
+
+	pll = __raw_readl(dpll_base + AR934X_SRIF_CPU_DPLL2_REG);
+	if (pll & AR934X_SRIF_DPLL2_LOCAL_PLL) {
+		out_div = (pll >> AR934X_SRIF_DPLL2_OUTDIV_SHIFT) &
+			  AR934X_SRIF_DPLL2_OUTDIV_MASK;
+		pll = __raw_readl(dpll_base + AR934X_SRIF_CPU_DPLL1_REG);
+		nint = (pll >> AR934X_SRIF_DPLL1_NINT_SHIFT) &
+		       AR934X_SRIF_DPLL1_NINT_MASK;
+		nfrac = pll & AR934X_SRIF_DPLL1_NFRAC_MASK;
+		ref_div = (pll >> AR934X_SRIF_DPLL1_REFDIV_SHIFT) &
+			  AR934X_SRIF_DPLL1_REFDIV_MASK;
+		frac = 1 << 18;
+	} else {
+		pll = __raw_readl(pll_base + AR934X_PLL_CPU_CONFIG_REG);
+		out_div = (pll >> AR934X_PLL_CPU_CONFIG_OUTDIV_SHIFT) &
+			AR934X_PLL_CPU_CONFIG_OUTDIV_MASK;
+		ref_div = (pll >> AR934X_PLL_CPU_CONFIG_REFDIV_SHIFT) &
+			  AR934X_PLL_CPU_CONFIG_REFDIV_MASK;
+		nint = (pll >> AR934X_PLL_CPU_CONFIG_NINT_SHIFT) &
+		       AR934X_PLL_CPU_CONFIG_NINT_MASK;
+		nfrac = (pll >> AR934X_PLL_CPU_CONFIG_NFRAC_SHIFT) &
+			AR934X_PLL_CPU_CONFIG_NFRAC_MASK;
+		frac = 1 << 6;
+	}
+
+	cpu_pll = ar934x_get_pll_freq(ref_rate, ref_div, nint,
+				      nfrac, frac, out_div);
+
+	pll = __raw_readl(dpll_base + AR934X_SRIF_DDR_DPLL2_REG);
+	if (pll & AR934X_SRIF_DPLL2_LOCAL_PLL) {
+		out_div = (pll >> AR934X_SRIF_DPLL2_OUTDIV_SHIFT) &
+			  AR934X_SRIF_DPLL2_OUTDIV_MASK;
+		pll = __raw_readl(dpll_base + AR934X_SRIF_DDR_DPLL1_REG);
+		nint = (pll >> AR934X_SRIF_DPLL1_NINT_SHIFT) &
+		       AR934X_SRIF_DPLL1_NINT_MASK;
+		nfrac = pll & AR934X_SRIF_DPLL1_NFRAC_MASK;
+		ref_div = (pll >> AR934X_SRIF_DPLL1_REFDIV_SHIFT) &
+			  AR934X_SRIF_DPLL1_REFDIV_MASK;
+		frac = 1 << 18;
+	} else {
+		pll = __raw_readl(pll_base + AR934X_PLL_DDR_CONFIG_REG);
+		out_div = (pll >> AR934X_PLL_DDR_CONFIG_OUTDIV_SHIFT) &
+			  AR934X_PLL_DDR_CONFIG_OUTDIV_MASK;
+		ref_div = (pll >> AR934X_PLL_DDR_CONFIG_REFDIV_SHIFT) &
+			   AR934X_PLL_DDR_CONFIG_REFDIV_MASK;
+		nint = (pll >> AR934X_PLL_DDR_CONFIG_NINT_SHIFT) &
+		       AR934X_PLL_DDR_CONFIG_NINT_MASK;
+		nfrac = (pll >> AR934X_PLL_DDR_CONFIG_NFRAC_SHIFT) &
+			AR934X_PLL_DDR_CONFIG_NFRAC_MASK;
+		frac = 1 << 10;
+	}
+
+	ddr_pll = ar934x_get_pll_freq(ref_rate, ref_div, nint,
+				      nfrac, frac, out_div);
+
+	clk_ctrl = __raw_readl(pll_base + AR934X_PLL_CPU_DDR_CLK_CTRL_REG);
+
+	postdiv = (clk_ctrl >> AR934X_PLL_CPU_DDR_CLK_CTRL_CPU_POST_DIV_SHIFT) &
+		  AR934X_PLL_CPU_DDR_CLK_CTRL_CPU_POST_DIV_MASK;
+
+	if (clk_ctrl & AR934X_PLL_CPU_DDR_CLK_CTRL_CPU_PLL_BYPASS)
+		cpu_rate = ref_rate;
+	else if (clk_ctrl & AR934X_PLL_CPU_DDR_CLK_CTRL_CPUCLK_FROM_CPUPLL)
+		cpu_rate = cpu_pll / (postdiv + 1);
+	else
+		cpu_rate = ddr_pll / (postdiv + 1);
+
+	postdiv = (clk_ctrl >> AR934X_PLL_CPU_DDR_CLK_CTRL_DDR_POST_DIV_SHIFT) &
+		  AR934X_PLL_CPU_DDR_CLK_CTRL_DDR_POST_DIV_MASK;
+
+	if (clk_ctrl & AR934X_PLL_CPU_DDR_CLK_CTRL_DDR_PLL_BYPASS)
+		ddr_rate = ref_rate;
+	else if (clk_ctrl & AR934X_PLL_CPU_DDR_CLK_CTRL_DDRCLK_FROM_DDRPLL)
+		ddr_rate = ddr_pll / (postdiv + 1);
+	else
+		ddr_rate = cpu_pll / (postdiv + 1);
+
+	postdiv = (clk_ctrl >> AR934X_PLL_CPU_DDR_CLK_CTRL_AHB_POST_DIV_SHIFT) &
+		  AR934X_PLL_CPU_DDR_CLK_CTRL_AHB_POST_DIV_MASK;
+
+	if (clk_ctrl & AR934X_PLL_CPU_DDR_CLK_CTRL_AHB_PLL_BYPASS)
+		ahb_rate = ref_rate;
+	else if (clk_ctrl & AR934X_PLL_CPU_DDR_CLK_CTRL_AHBCLK_FROM_DDRPLL)
+		ahb_rate = ddr_pll / (postdiv + 1);
+	else
+		ahb_rate = cpu_pll / (postdiv + 1);
+
+	ath79_set_clk(ATH79_CLK_CPU, cpu_rate);
+	ath79_set_clk(ATH79_CLK_DDR, ddr_rate);
+	ath79_set_clk(ATH79_CLK_AHB, ahb_rate);
+
+	clk_ctrl = __raw_readl(pll_base + AR934X_PLL_SWITCH_CLOCK_CONTROL_REG);
+	if (clk_ctrl & AR934X_PLL_SWITCH_CLOCK_CONTROL_MDIO_CLK_SEL)
+		ath79_set_clk(ATH79_CLK_MDIO, 100 * 1000 * 1000);
+
+	iounmap(dpll_base);
+}
+
+static void __init qca953x_clocks_init(void __iomem *pll_base)
+{
+	unsigned long ref_rate;
+	unsigned long cpu_rate;
+	unsigned long ddr_rate;
+	unsigned long ahb_rate;
+	u32 pll, out_div, ref_div, nint, frac, clk_ctrl, postdiv;
+	u32 cpu_pll, ddr_pll;
+	u32 bootstrap;
+
+	bootstrap = ath79_reset_rr(QCA953X_RESET_REG_BOOTSTRAP);
+	if (bootstrap &	QCA953X_BOOTSTRAP_REF_CLK_40)
+		ref_rate = 40 * 1000 * 1000;
+	else
+		ref_rate = 25 * 1000 * 1000;
+
+	ref_rate = ath79_setup_ref_clk(ref_rate);
+
+	pll = __raw_readl(pll_base + QCA953X_PLL_CPU_CONFIG_REG);
+	out_div = (pll >> QCA953X_PLL_CPU_CONFIG_OUTDIV_SHIFT) &
+		  QCA953X_PLL_CPU_CONFIG_OUTDIV_MASK;
+	ref_div = (pll >> QCA953X_PLL_CPU_CONFIG_REFDIV_SHIFT) &
+		  QCA953X_PLL_CPU_CONFIG_REFDIV_MASK;
+	nint = (pll >> QCA953X_PLL_CPU_CONFIG_NINT_SHIFT) &
+	       QCA953X_PLL_CPU_CONFIG_NINT_MASK;
+	frac = (pll >> QCA953X_PLL_CPU_CONFIG_NFRAC_SHIFT) &
+	       QCA953X_PLL_CPU_CONFIG_NFRAC_MASK;
+
+	cpu_pll = nint * ref_rate / ref_div;
+	cpu_pll += frac * (ref_rate >> 6) / ref_div;
+	cpu_pll /= (1 << out_div);
+
+	pll = __raw_readl(pll_base + QCA953X_PLL_DDR_CONFIG_REG);
+	out_div = (pll >> QCA953X_PLL_DDR_CONFIG_OUTDIV_SHIFT) &
+		  QCA953X_PLL_DDR_CONFIG_OUTDIV_MASK;
+	ref_div = (pll >> QCA953X_PLL_DDR_CONFIG_REFDIV_SHIFT) &
+		  QCA953X_PLL_DDR_CONFIG_REFDIV_MASK;
+	nint = (pll >> QCA953X_PLL_DDR_CONFIG_NINT_SHIFT) &
+	       QCA953X_PLL_DDR_CONFIG_NINT_MASK;
+	frac = (pll >> QCA953X_PLL_DDR_CONFIG_NFRAC_SHIFT) &
+	       QCA953X_PLL_DDR_CONFIG_NFRAC_MASK;
+
+	ddr_pll = nint * ref_rate / ref_div;
+	ddr_pll += frac * (ref_rate >> 6) / (ref_div << 4);
+	ddr_pll /= (1 << out_div);
+
+	clk_ctrl = __raw_readl(pll_base + QCA953X_PLL_CLK_CTRL_REG);
+
+	postdiv = (clk_ctrl >> QCA953X_PLL_CLK_CTRL_CPU_POST_DIV_SHIFT) &
+		  QCA953X_PLL_CLK_CTRL_CPU_POST_DIV_MASK;
+
+	if (clk_ctrl & QCA953X_PLL_CLK_CTRL_CPU_PLL_BYPASS)
+		cpu_rate = ref_rate;
+	else if (clk_ctrl & QCA953X_PLL_CLK_CTRL_CPUCLK_FROM_CPUPLL)
+		cpu_rate = cpu_pll / (postdiv + 1);
+	else
+		cpu_rate = ddr_pll / (postdiv + 1);
+
+	postdiv = (clk_ctrl >> QCA953X_PLL_CLK_CTRL_DDR_POST_DIV_SHIFT) &
+		  QCA953X_PLL_CLK_CTRL_DDR_POST_DIV_MASK;
+
+	if (clk_ctrl & QCA953X_PLL_CLK_CTRL_DDR_PLL_BYPASS)
+		ddr_rate = ref_rate;
+	else if (clk_ctrl & QCA953X_PLL_CLK_CTRL_DDRCLK_FROM_DDRPLL)
+		ddr_rate = ddr_pll / (postdiv + 1);
+	else
+		ddr_rate = cpu_pll / (postdiv + 1);
+
+	postdiv = (clk_ctrl >> QCA953X_PLL_CLK_CTRL_AHB_POST_DIV_SHIFT) &
+		  QCA953X_PLL_CLK_CTRL_AHB_POST_DIV_MASK;
+
+	if (clk_ctrl & QCA953X_PLL_CLK_CTRL_AHB_PLL_BYPASS)
+		ahb_rate = ref_rate;
+	else if (clk_ctrl & QCA953X_PLL_CLK_CTRL_AHBCLK_FROM_DDRPLL)
+		ahb_rate = ddr_pll / (postdiv + 1);
+	else
+		ahb_rate = cpu_pll / (postdiv + 1);
+
+	ath79_set_clk(ATH79_CLK_CPU, cpu_rate);
+	ath79_set_clk(ATH79_CLK_DDR, ddr_rate);
+	ath79_set_clk(ATH79_CLK_AHB, ahb_rate);
+}
+
+static void __init qca955x_clocks_init(void __iomem *pll_base)
+{
+	unsigned long ref_rate;
+	unsigned long cpu_rate;
+	unsigned long ddr_rate;
+	unsigned long ahb_rate;
+	u32 pll, out_div, ref_div, nint, frac, clk_ctrl, postdiv;
+	u32 cpu_pll, ddr_pll;
+	u32 bootstrap;
+
+	bootstrap = ath79_reset_rr(QCA955X_RESET_REG_BOOTSTRAP);
+	if (bootstrap &	QCA955X_BOOTSTRAP_REF_CLK_40)
+		ref_rate = 40 * 1000 * 1000;
+	else
+		ref_rate = 25 * 1000 * 1000;
+
+	ref_rate = ath79_setup_ref_clk(ref_rate);
+
+	pll = __raw_readl(pll_base + QCA955X_PLL_CPU_CONFIG_REG);
+	out_div = (pll >> QCA955X_PLL_CPU_CONFIG_OUTDIV_SHIFT) &
+		  QCA955X_PLL_CPU_CONFIG_OUTDIV_MASK;
+	ref_div = (pll >> QCA955X_PLL_CPU_CONFIG_REFDIV_SHIFT) &
+		  QCA955X_PLL_CPU_CONFIG_REFDIV_MASK;
+	nint = (pll >> QCA955X_PLL_CPU_CONFIG_NINT_SHIFT) &
+	       QCA955X_PLL_CPU_CONFIG_NINT_MASK;
+	frac = (pll >> QCA955X_PLL_CPU_CONFIG_NFRAC_SHIFT) &
+	       QCA955X_PLL_CPU_CONFIG_NFRAC_MASK;
+
+	cpu_pll = nint * ref_rate / ref_div;
+	cpu_pll += frac * ref_rate / (ref_div * (1 << 6));
+	cpu_pll /= (1 << out_div);
+
+	pll = __raw_readl(pll_base + QCA955X_PLL_DDR_CONFIG_REG);
+	out_div = (pll >> QCA955X_PLL_DDR_CONFIG_OUTDIV_SHIFT) &
+		  QCA955X_PLL_DDR_CONFIG_OUTDIV_MASK;
+	ref_div = (pll >> QCA955X_PLL_DDR_CONFIG_REFDIV_SHIFT) &
+		  QCA955X_PLL_DDR_CONFIG_REFDIV_MASK;
+	nint = (pll >> QCA955X_PLL_DDR_CONFIG_NINT_SHIFT) &
+	       QCA955X_PLL_DDR_CONFIG_NINT_MASK;
+	frac = (pll >> QCA955X_PLL_DDR_CONFIG_NFRAC_SHIFT) &
+	       QCA955X_PLL_DDR_CONFIG_NFRAC_MASK;
+
+	ddr_pll = nint * ref_rate / ref_div;
+	ddr_pll += frac * ref_rate / (ref_div * (1 << 10));
+	ddr_pll /= (1 << out_div);
+
+	clk_ctrl = __raw_readl(pll_base + QCA955X_PLL_CLK_CTRL_REG);
+
+	postdiv = (clk_ctrl >> QCA955X_PLL_CLK_CTRL_CPU_POST_DIV_SHIFT) &
+		  QCA955X_PLL_CLK_CTRL_CPU_POST_DIV_MASK;
+
+	if (clk_ctrl & QCA955X_PLL_CLK_CTRL_CPU_PLL_BYPASS)
+		cpu_rate = ref_rate;
+	else if (clk_ctrl & QCA955X_PLL_CLK_CTRL_CPUCLK_FROM_CPUPLL)
+		cpu_rate = ddr_pll / (postdiv + 1);
+	else
+		cpu_rate = cpu_pll / (postdiv + 1);
+
+	postdiv = (clk_ctrl >> QCA955X_PLL_CLK_CTRL_DDR_POST_DIV_SHIFT) &
+		  QCA955X_PLL_CLK_CTRL_DDR_POST_DIV_MASK;
+
+	if (clk_ctrl & QCA955X_PLL_CLK_CTRL_DDR_PLL_BYPASS)
+		ddr_rate = ref_rate;
+	else if (clk_ctrl & QCA955X_PLL_CLK_CTRL_DDRCLK_FROM_DDRPLL)
+		ddr_rate = cpu_pll / (postdiv + 1);
+	else
+		ddr_rate = ddr_pll / (postdiv + 1);
+
+	postdiv = (clk_ctrl >> QCA955X_PLL_CLK_CTRL_AHB_POST_DIV_SHIFT) &
+		  QCA955X_PLL_CLK_CTRL_AHB_POST_DIV_MASK;
+
+	if (clk_ctrl & QCA955X_PLL_CLK_CTRL_AHB_PLL_BYPASS)
+		ahb_rate = ref_rate;
+	else if (clk_ctrl & QCA955X_PLL_CLK_CTRL_AHBCLK_FROM_DDRPLL)
+		ahb_rate = ddr_pll / (postdiv + 1);
+	else
+		ahb_rate = cpu_pll / (postdiv + 1);
+
+	ath79_set_clk(ATH79_CLK_CPU, cpu_rate);
+	ath79_set_clk(ATH79_CLK_DDR, ddr_rate);
+	ath79_set_clk(ATH79_CLK_AHB, ahb_rate);
+}
+
+static void __init qca956x_clocks_init(void __iomem *pll_base)
+{
+	unsigned long ref_rate;
+	unsigned long cpu_rate;
+	unsigned long ddr_rate;
+	unsigned long ahb_rate;
+	u32 pll, out_div, ref_div, nint, hfrac, lfrac, clk_ctrl, postdiv;
+	u32 cpu_pll, ddr_pll;
+	u32 bootstrap;
+
+	/*
+	 * QCA956x timer init workaround has to be applied right before setting
+	 * up the clock. Else, there will be no jiffies
+	 */
+	u32 misc;
+
+	misc = ath79_reset_rr(AR71XX_RESET_REG_MISC_INT_ENABLE);
+	misc |= MISC_INT_MIPS_SI_TIMERINT_MASK;
+	ath79_reset_wr(AR71XX_RESET_REG_MISC_INT_ENABLE, misc);
+
+	bootstrap = ath79_reset_rr(QCA956X_RESET_REG_BOOTSTRAP);
+	if (bootstrap &	QCA956X_BOOTSTRAP_REF_CLK_40)
+		ref_rate = 40 * 1000 * 1000;
+	else
+		ref_rate = 25 * 1000 * 1000;
+
+	ref_rate = ath79_setup_ref_clk(ref_rate);
+
+	pll = __raw_readl(pll_base + QCA956X_PLL_CPU_CONFIG_REG);
+	out_div = (pll >> QCA956X_PLL_CPU_CONFIG_OUTDIV_SHIFT) &
+		  QCA956X_PLL_CPU_CONFIG_OUTDIV_MASK;
+	ref_div = (pll >> QCA956X_PLL_CPU_CONFIG_REFDIV_SHIFT) &
+		  QCA956X_PLL_CPU_CONFIG_REFDIV_MASK;
+
+	pll = __raw_readl(pll_base + QCA956X_PLL_CPU_CONFIG1_REG);
+	nint = (pll >> QCA956X_PLL_CPU_CONFIG1_NINT_SHIFT) &
+	       QCA956X_PLL_CPU_CONFIG1_NINT_MASK;
+	hfrac = (pll >> QCA956X_PLL_CPU_CONFIG1_NFRAC_H_SHIFT) &
+	       QCA956X_PLL_CPU_CONFIG1_NFRAC_H_MASK;
+	lfrac = (pll >> QCA956X_PLL_CPU_CONFIG1_NFRAC_L_SHIFT) &
+	       QCA956X_PLL_CPU_CONFIG1_NFRAC_L_MASK;
+
+	cpu_pll = nint * ref_rate / ref_div;
+	cpu_pll += (lfrac * ref_rate) / ((ref_div * 25) << 13);
+	cpu_pll += (hfrac >> 13) * ref_rate / ref_div;
+	cpu_pll /= (1 << out_div);
+
+	pll = __raw_readl(pll_base + QCA956X_PLL_DDR_CONFIG_REG);
+	out_div = (pll >> QCA956X_PLL_DDR_CONFIG_OUTDIV_SHIFT) &
+		  QCA956X_PLL_DDR_CONFIG_OUTDIV_MASK;
+	ref_div = (pll >> QCA956X_PLL_DDR_CONFIG_REFDIV_SHIFT) &
+		  QCA956X_PLL_DDR_CONFIG_REFDIV_MASK;
+	pll = __raw_readl(pll_base + QCA956X_PLL_DDR_CONFIG1_REG);
+	nint = (pll >> QCA956X_PLL_DDR_CONFIG1_NINT_SHIFT) &
+	       QCA956X_PLL_DDR_CONFIG1_NINT_MASK;
+	hfrac = (pll >> QCA956X_PLL_DDR_CONFIG1_NFRAC_H_SHIFT) &
+	       QCA956X_PLL_DDR_CONFIG1_NFRAC_H_MASK;
+	lfrac = (pll >> QCA956X_PLL_DDR_CONFIG1_NFRAC_L_SHIFT) &
+	       QCA956X_PLL_DDR_CONFIG1_NFRAC_L_MASK;
+
+	ddr_pll = nint * ref_rate / ref_div;
+	ddr_pll += (lfrac * ref_rate) / ((ref_div * 25) << 13);
+	ddr_pll += (hfrac >> 13) * ref_rate / ref_div;
+	ddr_pll /= (1 << out_div);
+
+	clk_ctrl = __raw_readl(pll_base + QCA956X_PLL_CLK_CTRL_REG);
+
+	postdiv = (clk_ctrl >> QCA956X_PLL_CLK_CTRL_CPU_POST_DIV_SHIFT) &
+		  QCA956X_PLL_CLK_CTRL_CPU_POST_DIV_MASK;
+
+	if (clk_ctrl & QCA956X_PLL_CLK_CTRL_CPU_PLL_BYPASS)
+		cpu_rate = ref_rate;
+	else if (clk_ctrl & QCA956X_PLL_CLK_CTRL_CPU_DDRCLK_FROM_CPUPLL)
+		cpu_rate = ddr_pll / (postdiv + 1);
+	else
+		cpu_rate = cpu_pll / (postdiv + 1);
+
+	postdiv = (clk_ctrl >> QCA956X_PLL_CLK_CTRL_DDR_POST_DIV_SHIFT) &
+		  QCA956X_PLL_CLK_CTRL_DDR_POST_DIV_MASK;
+
+	if (clk_ctrl & QCA956X_PLL_CLK_CTRL_DDR_PLL_BYPASS)
+		ddr_rate = ref_rate;
+	else if (clk_ctrl & QCA956X_PLL_CLK_CTRL_CPU_DDRCLK_FROM_DDRPLL)
+		ddr_rate = cpu_pll / (postdiv + 1);
+	else
+		ddr_rate = ddr_pll / (postdiv + 1);
+
+	postdiv = (clk_ctrl >> QCA956X_PLL_CLK_CTRL_AHB_POST_DIV_SHIFT) &
+		  QCA956X_PLL_CLK_CTRL_AHB_POST_DIV_MASK;
+
+	if (clk_ctrl & QCA956X_PLL_CLK_CTRL_AHB_PLL_BYPASS)
+		ahb_rate = ref_rate;
+	else if (clk_ctrl & QCA956X_PLL_CLK_CTRL_AHBCLK_FROM_DDRPLL)
+		ahb_rate = ddr_pll / (postdiv + 1);
+	else
+		ahb_rate = cpu_pll / (postdiv + 1);
+
+	ath79_set_clk(ATH79_CLK_CPU, cpu_rate);
+	ath79_set_clk(ATH79_CLK_DDR, ddr_rate);
+	ath79_set_clk(ATH79_CLK_AHB, ahb_rate);
+}
+
+static void __init ath79_clocks_init_dt(struct device_node *np)
+{
+	struct clk *ref_clk;
+	void __iomem *pll_base;
+
+	ref_clk = of_clk_get(np, 0);
+	if (!IS_ERR(ref_clk))
+		clks[ATH79_CLK_REF] = ref_clk;
+
+	pll_base = of_iomap(np, 0);
+	if (!pll_base) {
+		pr_err("%pOF: can't map pll registers\n", np);
+		goto err_clk;
+	}
+
+	if (of_device_is_compatible(np, "qca,ar7100-pll"))
+		ar71xx_clocks_init(pll_base);
+	else if (of_device_is_compatible(np, "qca,ar7240-pll") ||
+		 of_device_is_compatible(np, "qca,ar9130-pll"))
+		ar724x_clocks_init(pll_base);
+	else if (of_device_is_compatible(np, "qca,ar9330-pll"))
+		ar933x_clocks_init(pll_base);
+	else if (of_device_is_compatible(np, "qca,ar9340-pll"))
+		ar934x_clocks_init(pll_base);
+	else if (of_device_is_compatible(np, "qca,qca9530-pll"))
+		qca953x_clocks_init(pll_base);
+	else if (of_device_is_compatible(np, "qca,qca9550-pll"))
+		qca955x_clocks_init(pll_base);
+	else if (of_device_is_compatible(np, "qca,qca9560-pll"))
+		qca956x_clocks_init(pll_base);
+
+	if (!clks[ATH79_CLK_MDIO])
+		clks[ATH79_CLK_MDIO] = clks[ATH79_CLK_REF];
+
+	if (of_clk_add_provider(np, of_clk_src_onecell_get, &clk_data)) {
+		pr_err("%pOF: could not register clk provider\n", np);
+		goto err_iounmap;
+	}
+
+	return;
+
+err_iounmap:
+	iounmap(pll_base);
+
+err_clk:
+	clk_put(ref_clk);
+}
+
+CLK_OF_DECLARE(ar7100_clk, "qca,ar7100-pll", ath79_clocks_init_dt);
+CLK_OF_DECLARE(ar7240_clk, "qca,ar7240-pll", ath79_clocks_init_dt);
+CLK_OF_DECLARE(ar9130_clk, "qca,ar9130-pll", ath79_clocks_init_dt);
+CLK_OF_DECLARE(ar9330_clk, "qca,ar9330-pll", ath79_clocks_init_dt);
+CLK_OF_DECLARE(ar9340_clk, "qca,ar9340-pll", ath79_clocks_init_dt);
+CLK_OF_DECLARE(ar9530_clk, "qca,qca9530-pll", ath79_clocks_init_dt);
+CLK_OF_DECLARE(ar9550_clk, "qca,qca9550-pll", ath79_clocks_init_dt);
+CLK_OF_DECLARE(ar9560_clk, "qca,qca9560-pll", ath79_clocks_init_dt);
diff --git a/arch/mips/ath79/common.c b/arch/mips/ath79/common.c
new file mode 100644
index 000000000..137abbc65
--- /dev/null
+++ b/arch/mips/ath79/common.c
@@ -0,0 +1,149 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *  Atheros AR71XX/AR724X/AR913X common routines
+ *
+ *  Copyright (C) 2010-2011 Jaiganesh Narayanan <jnarayanan@atheros.com>
+ *  Copyright (C) 2008-2011 Gabor Juhos <juhosg@openwrt.org>
+ *  Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ *
+ *  Parts of this file are based on Atheros' 2.6.15/2.6.31 BSP
+ */
+
+#include <linux/kernel.h>
+#include <linux/export.h>
+#include <linux/types.h>
+#include <linux/spinlock.h>
+
+#include <asm/mach-ath79/ath79.h>
+#include <asm/mach-ath79/ar71xx_regs.h>
+#include "common.h"
+
+static DEFINE_SPINLOCK(ath79_device_reset_lock);
+
+u32 ath79_cpu_freq;
+EXPORT_SYMBOL_GPL(ath79_cpu_freq);
+
+u32 ath79_ahb_freq;
+EXPORT_SYMBOL_GPL(ath79_ahb_freq);
+
+u32 ath79_ddr_freq;
+EXPORT_SYMBOL_GPL(ath79_ddr_freq);
+
+enum ath79_soc_type ath79_soc;
+unsigned int ath79_soc_rev;
+
+void __iomem *ath79_pll_base;
+void __iomem *ath79_reset_base;
+EXPORT_SYMBOL_GPL(ath79_reset_base);
+static void __iomem *ath79_ddr_base;
+static void __iomem *ath79_ddr_wb_flush_base;
+static void __iomem *ath79_ddr_pci_win_base;
+
+void ath79_ddr_ctrl_init(void)
+{
+	ath79_ddr_base = ioremap(AR71XX_DDR_CTRL_BASE,
+					 AR71XX_DDR_CTRL_SIZE);
+	if (soc_is_ar913x() || soc_is_ar724x() || soc_is_ar933x()) {
+		ath79_ddr_wb_flush_base = ath79_ddr_base + 0x7c;
+		ath79_ddr_pci_win_base = 0;
+	} else {
+		ath79_ddr_wb_flush_base = ath79_ddr_base + 0x9c;
+		ath79_ddr_pci_win_base = ath79_ddr_base + 0x7c;
+	}
+}
+EXPORT_SYMBOL_GPL(ath79_ddr_ctrl_init);
+
+void ath79_ddr_wb_flush(u32 reg)
+{
+	void __iomem *flush_reg = ath79_ddr_wb_flush_base + (reg * 4);
+
+	/* Flush the DDR write buffer. */
+	__raw_writel(0x1, flush_reg);
+	while (__raw_readl(flush_reg) & 0x1)
+		;
+
+	/* It must be run twice. */
+	__raw_writel(0x1, flush_reg);
+	while (__raw_readl(flush_reg) & 0x1)
+		;
+}
+EXPORT_SYMBOL_GPL(ath79_ddr_wb_flush);
+
+void ath79_ddr_set_pci_windows(void)
+{
+	BUG_ON(!ath79_ddr_pci_win_base);
+
+	__raw_writel(AR71XX_PCI_WIN0_OFFS, ath79_ddr_pci_win_base + 0x0);
+	__raw_writel(AR71XX_PCI_WIN1_OFFS, ath79_ddr_pci_win_base + 0x4);
+	__raw_writel(AR71XX_PCI_WIN2_OFFS, ath79_ddr_pci_win_base + 0x8);
+	__raw_writel(AR71XX_PCI_WIN3_OFFS, ath79_ddr_pci_win_base + 0xc);
+	__raw_writel(AR71XX_PCI_WIN4_OFFS, ath79_ddr_pci_win_base + 0x10);
+	__raw_writel(AR71XX_PCI_WIN5_OFFS, ath79_ddr_pci_win_base + 0x14);
+	__raw_writel(AR71XX_PCI_WIN6_OFFS, ath79_ddr_pci_win_base + 0x18);
+	__raw_writel(AR71XX_PCI_WIN7_OFFS, ath79_ddr_pci_win_base + 0x1c);
+}
+EXPORT_SYMBOL_GPL(ath79_ddr_set_pci_windows);
+
+void ath79_device_reset_set(u32 mask)
+{
+	unsigned long flags;
+	u32 reg;
+	u32 t;
+
+	if (soc_is_ar71xx())
+		reg = AR71XX_RESET_REG_RESET_MODULE;
+	else if (soc_is_ar724x())
+		reg = AR724X_RESET_REG_RESET_MODULE;
+	else if (soc_is_ar913x())
+		reg = AR913X_RESET_REG_RESET_MODULE;
+	else if (soc_is_ar933x())
+		reg = AR933X_RESET_REG_RESET_MODULE;
+	else if (soc_is_ar934x())
+		reg = AR934X_RESET_REG_RESET_MODULE;
+	else if (soc_is_qca953x())
+		reg = QCA953X_RESET_REG_RESET_MODULE;
+	else if (soc_is_qca955x())
+		reg = QCA955X_RESET_REG_RESET_MODULE;
+	else if (soc_is_qca956x() || soc_is_tp9343())
+		reg = QCA956X_RESET_REG_RESET_MODULE;
+	else
+		BUG();
+
+	spin_lock_irqsave(&ath79_device_reset_lock, flags);
+	t = ath79_reset_rr(reg);
+	ath79_reset_wr(reg, t | mask);
+	spin_unlock_irqrestore(&ath79_device_reset_lock, flags);
+}
+EXPORT_SYMBOL_GPL(ath79_device_reset_set);
+
+void ath79_device_reset_clear(u32 mask)
+{
+	unsigned long flags;
+	u32 reg;
+	u32 t;
+
+	if (soc_is_ar71xx())
+		reg = AR71XX_RESET_REG_RESET_MODULE;
+	else if (soc_is_ar724x())
+		reg = AR724X_RESET_REG_RESET_MODULE;
+	else if (soc_is_ar913x())
+		reg = AR913X_RESET_REG_RESET_MODULE;
+	else if (soc_is_ar933x())
+		reg = AR933X_RESET_REG_RESET_MODULE;
+	else if (soc_is_ar934x())
+		reg = AR934X_RESET_REG_RESET_MODULE;
+	else if (soc_is_qca953x())
+		reg = QCA953X_RESET_REG_RESET_MODULE;
+	else if (soc_is_qca955x())
+		reg = QCA955X_RESET_REG_RESET_MODULE;
+	else if (soc_is_qca956x() || soc_is_tp9343())
+		reg = QCA956X_RESET_REG_RESET_MODULE;
+	else
+		BUG();
+
+	spin_lock_irqsave(&ath79_device_reset_lock, flags);
+	t = ath79_reset_rr(reg);
+	ath79_reset_wr(reg, t & ~mask);
+	spin_unlock_irqrestore(&ath79_device_reset_lock, flags);
+}
+EXPORT_SYMBOL_GPL(ath79_device_reset_clear);
diff --git a/arch/mips/ath79/common.h b/arch/mips/ath79/common.h
new file mode 100644
index 000000000..47fb66d7b
--- /dev/null
+++ b/arch/mips/ath79/common.h
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *  Atheros AR71XX/AR724X/AR913X common definitions
+ *
+ *  Copyright (C) 2008-2011 Gabor Juhos <juhosg@openwrt.org>
+ *  Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ *
+ *  Parts of this file are based on Atheros' 2.6.15 BSP
+ */
+
+#ifndef __ATH79_COMMON_H
+#define __ATH79_COMMON_H
+
+#include <linux/types.h>
+
+#define ATH79_MEM_SIZE_MIN	(2 * 1024 * 1024)
+#define ATH79_MEM_SIZE_MAX	(256 * 1024 * 1024)
+
+void ath79_ddr_ctrl_init(void);
+
+#endif /* __ATH79_COMMON_H */
diff --git a/arch/mips/ath79/early_printk.c b/arch/mips/ath79/early_printk.c
new file mode 100644
index 000000000..34c4dfdf4
--- /dev/null
+++ b/arch/mips/ath79/early_printk.c
@@ -0,0 +1,144 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *  Atheros AR7XXX/AR9XXX SoC early printk support
+ *
+ *  Copyright (C) 2008-2011 Gabor Juhos <juhosg@openwrt.org>
+ *  Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ */
+
+#include <linux/io.h>
+#include <linux/errno.h>
+#include <linux/serial.h>
+#include <linux/serial_reg.h>
+#include <asm/addrspace.h>
+#include <asm/setup.h>
+
+#include <asm/mach-ath79/ath79.h>
+#include <asm/mach-ath79/ar71xx_regs.h>
+#include <asm/mach-ath79/ar933x_uart.h>
+
+static void (*_prom_putchar)(char);
+
+static inline void prom_putchar_wait(void __iomem *reg, u32 val)
+{
+	u32 t;
+
+	do {
+		t = __raw_readl(reg);
+		if ((t & val) == val)
+			break;
+	} while (1);
+}
+
+static void prom_putchar_ar71xx(char ch)
+{
+	void __iomem *base = (void __iomem *)(KSEG1ADDR(AR71XX_UART_BASE));
+
+	prom_putchar_wait(base + UART_LSR * 4, UART_LSR_BOTH_EMPTY);
+	__raw_writel((unsigned char)ch, base + UART_TX * 4);
+	prom_putchar_wait(base + UART_LSR * 4, UART_LSR_BOTH_EMPTY);
+}
+
+static void prom_putchar_ar933x(char ch)
+{
+	void __iomem *base = (void __iomem *)(KSEG1ADDR(AR933X_UART_BASE));
+
+	prom_putchar_wait(base + AR933X_UART_DATA_REG, AR933X_UART_DATA_TX_CSR);
+	__raw_writel(AR933X_UART_DATA_TX_CSR | (unsigned char)ch,
+		     base + AR933X_UART_DATA_REG);
+	prom_putchar_wait(base + AR933X_UART_DATA_REG, AR933X_UART_DATA_TX_CSR);
+}
+
+static void prom_putchar_dummy(char ch)
+{
+	/* nothing to do */
+}
+
+static void prom_enable_uart(u32 id)
+{
+	void __iomem *gpio_base;
+	u32 uart_en;
+	u32 t;
+
+	switch (id) {
+	case REV_ID_MAJOR_AR71XX:
+		uart_en = AR71XX_GPIO_FUNC_UART_EN;
+		break;
+
+	case REV_ID_MAJOR_AR7240:
+	case REV_ID_MAJOR_AR7241:
+	case REV_ID_MAJOR_AR7242:
+		uart_en = AR724X_GPIO_FUNC_UART_EN;
+		break;
+
+	case REV_ID_MAJOR_AR913X:
+		uart_en = AR913X_GPIO_FUNC_UART_EN;
+		break;
+
+	case REV_ID_MAJOR_AR9330:
+	case REV_ID_MAJOR_AR9331:
+		uart_en = AR933X_GPIO_FUNC_UART_EN;
+		break;
+
+	case REV_ID_MAJOR_AR9341:
+	case REV_ID_MAJOR_AR9342:
+	case REV_ID_MAJOR_AR9344:
+		/* TODO */
+	default:
+		return;
+	}
+
+	gpio_base = (void __iomem *)KSEG1ADDR(AR71XX_GPIO_BASE);
+	t = __raw_readl(gpio_base + AR71XX_GPIO_REG_FUNC);
+	t |= uart_en;
+	__raw_writel(t, gpio_base + AR71XX_GPIO_REG_FUNC);
+}
+
+static void prom_putchar_init(void)
+{
+	void __iomem *base;
+	u32 id;
+
+	base = (void __iomem *)(KSEG1ADDR(AR71XX_RESET_BASE));
+	id = __raw_readl(base + AR71XX_RESET_REG_REV_ID);
+	id &= REV_ID_MAJOR_MASK;
+
+	switch (id) {
+	case REV_ID_MAJOR_AR71XX:
+	case REV_ID_MAJOR_AR7240:
+	case REV_ID_MAJOR_AR7241:
+	case REV_ID_MAJOR_AR7242:
+	case REV_ID_MAJOR_AR913X:
+	case REV_ID_MAJOR_AR9341:
+	case REV_ID_MAJOR_AR9342:
+	case REV_ID_MAJOR_AR9344:
+	case REV_ID_MAJOR_QCA9533:
+	case REV_ID_MAJOR_QCA9533_V2:
+	case REV_ID_MAJOR_QCA9556:
+	case REV_ID_MAJOR_QCA9558:
+	case REV_ID_MAJOR_TP9343:
+	case REV_ID_MAJOR_QCA956X:
+	case REV_ID_MAJOR_QCN550X:
+		_prom_putchar = prom_putchar_ar71xx;
+		break;
+
+	case REV_ID_MAJOR_AR9330:
+	case REV_ID_MAJOR_AR9331:
+		_prom_putchar = prom_putchar_ar933x;
+		break;
+
+	default:
+		_prom_putchar = prom_putchar_dummy;
+		return;
+	}
+
+	prom_enable_uart(id);
+}
+
+void prom_putchar(char ch)
+{
+	if (!_prom_putchar)
+		prom_putchar_init();
+
+	_prom_putchar(ch);
+}
diff --git a/arch/mips/ath79/prom.c b/arch/mips/ath79/prom.c
new file mode 100644
index 000000000..cc6dc5600
--- /dev/null
+++ b/arch/mips/ath79/prom.c
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *  Atheros AR71XX/AR724X/AR913X specific prom routines
+ *
+ *  Copyright (C) 2015 Laurent Fasnacht <l@libres.ch>
+ *  Copyright (C) 2008-2010 Gabor Juhos <juhosg@openwrt.org>
+ *  Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/string.h>
+#include <linux/initrd.h>
+
+#include <asm/bootinfo.h>
+#include <asm/addrspace.h>
+#include <asm/fw/fw.h>
+
+#include "common.h"
+
+void __init prom_init(void)
+{
+	fw_init_cmdline();
+
+#ifdef CONFIG_BLK_DEV_INITRD
+	/* Read the initrd address from the firmware environment */
+	initrd_start = fw_getenvl("initrd_start");
+	if (initrd_start) {
+		initrd_start = KSEG0ADDR(initrd_start);
+		initrd_end = initrd_start + fw_getenvl("initrd_size");
+	}
+#endif
+}
diff --git a/arch/mips/ath79/setup.c b/arch/mips/ath79/setup.c
new file mode 100644
index 000000000..4e18cdcf6
--- /dev/null
+++ b/arch/mips/ath79/setup.c
@@ -0,0 +1,271 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *  Atheros AR71XX/AR724X/AR913X specific setup
+ *
+ *  Copyright (C) 2010-2011 Jaiganesh Narayanan <jnarayanan@atheros.com>
+ *  Copyright (C) 2008-2011 Gabor Juhos <juhosg@openwrt.org>
+ *  Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ *
+ *  Parts of this file are based on Atheros' 2.6.15/2.6.31 BSP
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/memblock.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+#include <linux/of_clk.h>
+#include <linux/of_fdt.h>
+#include <linux/irqchip.h>
+
+#include <asm/bootinfo.h>
+#include <asm/idle.h>
+#include <asm/time.h>		/* for mips_hpt_frequency */
+#include <asm/reboot.h>		/* for _machine_{restart,halt} */
+#include <asm/prom.h>
+#include <asm/fw/fw.h>
+
+#include <asm/mach-ath79/ath79.h>
+#include <asm/mach-ath79/ar71xx_regs.h>
+#include "common.h"
+
+#define ATH79_SYS_TYPE_LEN	64
+
+static char ath79_sys_type[ATH79_SYS_TYPE_LEN];
+
+static void ath79_halt(void)
+{
+	while (1)
+		cpu_wait();
+}
+
+static void __init ath79_detect_sys_type(void)
+{
+	char *chip = "????";
+	u32 id;
+	u32 major;
+	u32 minor;
+	u32 rev = 0;
+	u32 ver = 1;
+
+	id = ath79_reset_rr(AR71XX_RESET_REG_REV_ID);
+	major = id & REV_ID_MAJOR_MASK;
+
+	switch (major) {
+	case REV_ID_MAJOR_AR71XX:
+		minor = id & AR71XX_REV_ID_MINOR_MASK;
+		rev = id >> AR71XX_REV_ID_REVISION_SHIFT;
+		rev &= AR71XX_REV_ID_REVISION_MASK;
+		switch (minor) {
+		case AR71XX_REV_ID_MINOR_AR7130:
+			ath79_soc = ATH79_SOC_AR7130;
+			chip = "7130";
+			break;
+
+		case AR71XX_REV_ID_MINOR_AR7141:
+			ath79_soc = ATH79_SOC_AR7141;
+			chip = "7141";
+			break;
+
+		case AR71XX_REV_ID_MINOR_AR7161:
+			ath79_soc = ATH79_SOC_AR7161;
+			chip = "7161";
+			break;
+		}
+		break;
+
+	case REV_ID_MAJOR_AR7240:
+		ath79_soc = ATH79_SOC_AR7240;
+		chip = "7240";
+		rev = id & AR724X_REV_ID_REVISION_MASK;
+		break;
+
+	case REV_ID_MAJOR_AR7241:
+		ath79_soc = ATH79_SOC_AR7241;
+		chip = "7241";
+		rev = id & AR724X_REV_ID_REVISION_MASK;
+		break;
+
+	case REV_ID_MAJOR_AR7242:
+		ath79_soc = ATH79_SOC_AR7242;
+		chip = "7242";
+		rev = id & AR724X_REV_ID_REVISION_MASK;
+		break;
+
+	case REV_ID_MAJOR_AR913X:
+		minor = id & AR913X_REV_ID_MINOR_MASK;
+		rev = id >> AR913X_REV_ID_REVISION_SHIFT;
+		rev &= AR913X_REV_ID_REVISION_MASK;
+		switch (minor) {
+		case AR913X_REV_ID_MINOR_AR9130:
+			ath79_soc = ATH79_SOC_AR9130;
+			chip = "9130";
+			break;
+
+		case AR913X_REV_ID_MINOR_AR9132:
+			ath79_soc = ATH79_SOC_AR9132;
+			chip = "9132";
+			break;
+		}
+		break;
+
+	case REV_ID_MAJOR_AR9330:
+		ath79_soc = ATH79_SOC_AR9330;
+		chip = "9330";
+		rev = id & AR933X_REV_ID_REVISION_MASK;
+		break;
+
+	case REV_ID_MAJOR_AR9331:
+		ath79_soc = ATH79_SOC_AR9331;
+		chip = "9331";
+		rev = id & AR933X_REV_ID_REVISION_MASK;
+		break;
+
+	case REV_ID_MAJOR_AR9341:
+		ath79_soc = ATH79_SOC_AR9341;
+		chip = "9341";
+		rev = id & AR934X_REV_ID_REVISION_MASK;
+		break;
+
+	case REV_ID_MAJOR_AR9342:
+		ath79_soc = ATH79_SOC_AR9342;
+		chip = "9342";
+		rev = id & AR934X_REV_ID_REVISION_MASK;
+		break;
+
+	case REV_ID_MAJOR_AR9344:
+		ath79_soc = ATH79_SOC_AR9344;
+		chip = "9344";
+		rev = id & AR934X_REV_ID_REVISION_MASK;
+		break;
+
+	case REV_ID_MAJOR_QCA9533_V2:
+		ver = 2;
+		ath79_soc_rev = 2;
+		fallthrough;
+	case REV_ID_MAJOR_QCA9533:
+		ath79_soc = ATH79_SOC_QCA9533;
+		chip = "9533";
+		rev = id & QCA953X_REV_ID_REVISION_MASK;
+		break;
+
+	case REV_ID_MAJOR_QCA9556:
+		ath79_soc = ATH79_SOC_QCA9556;
+		chip = "9556";
+		rev = id & QCA955X_REV_ID_REVISION_MASK;
+		break;
+
+	case REV_ID_MAJOR_QCA9558:
+		ath79_soc = ATH79_SOC_QCA9558;
+		chip = "9558";
+		rev = id & QCA955X_REV_ID_REVISION_MASK;
+		break;
+
+	case REV_ID_MAJOR_QCA956X:
+		ath79_soc = ATH79_SOC_QCA956X;
+		chip = "956X";
+		rev = id & QCA956X_REV_ID_REVISION_MASK;
+		break;
+
+	case REV_ID_MAJOR_QCN550X:
+		ath79_soc = ATH79_SOC_QCA956X;
+		chip = "550X";
+		rev = id & QCA956X_REV_ID_REVISION_MASK;
+		break;
+
+	case REV_ID_MAJOR_TP9343:
+		ath79_soc = ATH79_SOC_TP9343;
+		chip = "9343";
+		rev = id & QCA956X_REV_ID_REVISION_MASK;
+		break;
+
+	default:
+		panic("ath79: unknown SoC, id:0x%08x", id);
+	}
+
+	if (ver == 1)
+		ath79_soc_rev = rev;
+
+	if (soc_is_qca953x() || soc_is_qca955x() || soc_is_qca956x())
+		sprintf(ath79_sys_type, "Qualcomm Atheros QCA%s ver %u rev %u",
+			chip, ver, rev);
+	else if (soc_is_tp9343())
+		sprintf(ath79_sys_type, "Qualcomm Atheros TP%s rev %u",
+			chip, rev);
+	else
+		sprintf(ath79_sys_type, "Atheros AR%s rev %u", chip, rev);
+	pr_info("SoC: %s\n", ath79_sys_type);
+}
+
+const char *get_system_type(void)
+{
+	return ath79_sys_type;
+}
+
+unsigned int get_c0_compare_int(void)
+{
+	return CP0_LEGACY_COMPARE_IRQ;
+}
+
+void __init plat_mem_setup(void)
+{
+	void *dtb;
+
+	set_io_port_base(KSEG1);
+
+	/* Get the position of the FDT passed by the bootloader */
+	dtb = (void *)fw_getenvl("fdt_start");
+	if (dtb == NULL)
+		dtb = get_fdt();
+
+	if (dtb)
+		__dt_setup_arch((void *)KSEG0ADDR(dtb));
+
+	ath79_reset_base = ioremap(AR71XX_RESET_BASE,
+					   AR71XX_RESET_SIZE);
+	ath79_pll_base = ioremap(AR71XX_PLL_BASE,
+					 AR71XX_PLL_SIZE);
+	ath79_detect_sys_type();
+	ath79_ddr_ctrl_init();
+
+	detect_memory_region(0, ATH79_MEM_SIZE_MIN, ATH79_MEM_SIZE_MAX);
+
+	_machine_halt = ath79_halt;
+	pm_power_off = ath79_halt;
+}
+
+void __init plat_time_init(void)
+{
+	struct device_node *np;
+	struct clk *clk;
+	unsigned long cpu_clk_rate;
+
+	of_clk_init(NULL);
+
+	np = of_get_cpu_node(0, NULL);
+	if (!np) {
+		pr_err("Failed to get CPU node\n");
+		return;
+	}
+
+	clk = of_clk_get(np, 0);
+	if (IS_ERR(clk)) {
+		pr_err("Failed to get CPU clock: %ld\n", PTR_ERR(clk));
+		return;
+	}
+
+	cpu_clk_rate = clk_get_rate(clk);
+
+	pr_info("CPU clock: %lu.%03lu MHz\n",
+		cpu_clk_rate / 1000000, (cpu_clk_rate / 1000) % 1000);
+
+	mips_hpt_frequency = cpu_clk_rate / 2;
+
+	clk_put(clk);
+}
+
+void __init arch_init_irq(void)
+{
+	irqchip_init();
+}
diff --git a/arch/mips/bcm47xx/Kconfig b/arch/mips/bcm47xx/Kconfig
new file mode 100644
index 000000000..13d315ee6
--- /dev/null
+++ b/arch/mips/bcm47xx/Kconfig
@@ -0,0 +1,40 @@
+# SPDX-License-Identifier: GPL-2.0
+if BCM47XX
+
+config BCM47XX_SSB
+	bool "SSB Support for Broadcom BCM47XX"
+	select SYS_HAS_CPU_BMIPS32_3300
+	select SSB
+	select SSB_HOST_SOC
+	select SSB_DRIVER_MIPS
+	select SSB_DRIVER_EXTIF
+	select SSB_EMBEDDED
+	select SSB_PCIHOST if PCI
+	select SSB_B43_PCI_BRIDGE if PCI
+	select SSB_DRIVER_PCICORE if PCI
+	select SSB_PCICORE_HOSTMODE if PCI
+	select SSB_DRIVER_GPIO
+	default y
+	help
+	  Add support for old Broadcom BCM47xx boards with Sonics Silicon Backplane support.
+
+	  This will generate an image with support for SSB and MIPS32 R1 instruction set.
+
+config BCM47XX_BCMA
+	bool "BCMA Support for Broadcom BCM47XX"
+	select SYS_HAS_CPU_MIPS32_R2
+	select SYS_SUPPORTS_HIGHMEM
+	select CPU_MIPSR2_IRQ_VI
+	select BCMA
+	select BCMA_HOST_SOC
+	select BCMA_DRIVER_MIPS
+	select BCMA_DRIVER_PCI if PCI
+	select BCMA_DRIVER_PCI_HOSTMODE if PCI
+	select BCMA_DRIVER_GPIO
+	default y
+	help
+	  Add support for new Broadcom BCM47xx boards with Broadcom specific Advanced Microcontroller Bus.
+
+	  This will generate an image with support for BCMA and MIPS32 R2 instruction set.
+
+endif
diff --git a/arch/mips/bcm47xx/Makefile b/arch/mips/bcm47xx/Makefile
new file mode 100644
index 000000000..c7438a410
--- /dev/null
+++ b/arch/mips/bcm47xx/Makefile
@@ -0,0 +1,8 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Makefile for the BCM47XX specific kernel interface routines
+# under Linux.
+#
+
+obj-y				+= irq.o prom.o serial.o setup.o time.o
+obj-y				+= board.o buttons.o leds.o workarounds.o
diff --git a/arch/mips/bcm47xx/Platform b/arch/mips/bcm47xx/Platform
new file mode 100644
index 000000000..fe6daba3f
--- /dev/null
+++ b/arch/mips/bcm47xx/Platform
@@ -0,0 +1,6 @@
+#
+# Broadcom BCM47XX boards
+#
+cflags-$(CONFIG_BCM47XX)	+=					\
+		-I$(srctree)/arch/mips/include/asm/mach-bcm47xx
+load-$(CONFIG_BCM47XX)		:= 0xffffffff80001000
diff --git a/arch/mips/bcm47xx/bcm47xx_private.h b/arch/mips/bcm47xx/bcm47xx_private.h
new file mode 100644
index 000000000..bb96743bb
--- /dev/null
+++ b/arch/mips/bcm47xx/bcm47xx_private.h
@@ -0,0 +1,26 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef LINUX_BCM47XX_PRIVATE_H_
+#define LINUX_BCM47XX_PRIVATE_H_
+
+#ifndef pr_fmt
+#define pr_fmt(fmt)		"bcm47xx: " fmt
+#endif
+
+#include <linux/kernel.h>
+
+/* prom.c */
+void __init bcm47xx_prom_highmem_init(void);
+
+/* buttons.c */
+int __init bcm47xx_buttons_register(void);
+
+/* leds.c */
+void __init bcm47xx_leds_register(void);
+
+/* setup.c */
+void __init bcm47xx_bus_setup(void);
+
+/* workarounds.c */
+void __init bcm47xx_workarounds(void);
+
+#endif
diff --git a/arch/mips/bcm47xx/board.c b/arch/mips/bcm47xx/board.c
new file mode 100644
index 000000000..8ef002471
--- /dev/null
+++ b/arch/mips/bcm47xx/board.c
@@ -0,0 +1,368 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/errno.h>
+#include <linux/export.h>
+#include <linux/string.h>
+#include <bcm47xx.h>
+#include <bcm47xx_board.h>
+
+struct bcm47xx_board_type {
+	const enum bcm47xx_board board;
+	const char *name;
+};
+
+struct bcm47xx_board_type_list1 {
+	struct bcm47xx_board_type board;
+	const char *value1;
+};
+
+struct bcm47xx_board_type_list2 {
+	struct bcm47xx_board_type board;
+	const char *value1;
+	const char *value2;
+};
+
+struct bcm47xx_board_type_list3 {
+	struct bcm47xx_board_type board;
+	const char *value1;
+	const char *value2;
+	const char *value3;
+};
+
+struct bcm47xx_board_store {
+	enum bcm47xx_board board;
+	char name[BCM47XX_BOARD_MAX_NAME];
+};
+
+/* model_name */
+static const
+struct bcm47xx_board_type_list1 bcm47xx_board_list_model_name[] __initconst = {
+	{{BCM47XX_BOARD_DLINK_DIR130, "D-Link DIR-130"}, "DIR-130"},
+	{{BCM47XX_BOARD_DLINK_DIR330, "D-Link DIR-330"}, "DIR-330"},
+	{ {0}, NULL},
+};
+
+/* hardware_version */
+static const
+struct bcm47xx_board_type_list1 bcm47xx_board_list_hardware_version[] __initconst = {
+	{{BCM47XX_BOARD_ASUS_RTN10U, "Asus RT-N10U"}, "RTN10U"},
+	{{BCM47XX_BOARD_ASUS_RTN10D, "Asus RT-N10D"}, "RTN10D"},
+	{{BCM47XX_BOARD_ASUS_RTN12, "Asus RT-N12"}, "RT-N12"},
+	{{BCM47XX_BOARD_ASUS_RTN12B1, "Asus RT-N12B1"}, "RTN12B1"},
+	{{BCM47XX_BOARD_ASUS_RTN12C1, "Asus RT-N12C1"}, "RTN12C1"},
+	{{BCM47XX_BOARD_ASUS_RTN12D1, "Asus RT-N12D1"}, "RTN12D1"},
+	{{BCM47XX_BOARD_ASUS_RTN12HP, "Asus RT-N12HP"}, "RTN12HP"},
+	{{BCM47XX_BOARD_ASUS_RTN16, "Asus RT-N16"}, "RT-N16-"},
+	{{BCM47XX_BOARD_ASUS_WL320GE, "Asus WL320GE"}, "WL320G-"},
+	{{BCM47XX_BOARD_ASUS_WL330GE, "Asus WL330GE"}, "WL330GE-"},
+	{{BCM47XX_BOARD_ASUS_WL500GD, "Asus WL500GD"}, "WL500gd-"},
+	{{BCM47XX_BOARD_ASUS_WL500GPV1, "Asus WL500GP V1"}, "WL500gp-"},
+	{{BCM47XX_BOARD_ASUS_WL500GPV2, "Asus WL500GP V2"}, "WL500GPV2-"},
+	{{BCM47XX_BOARD_ASUS_WL500W, "Asus WL500W"}, "WL500gW-"},
+	{{BCM47XX_BOARD_ASUS_WL520GC, "Asus WL520GC"}, "WL520GC-"},
+	{{BCM47XX_BOARD_ASUS_WL520GU, "Asus WL520GU"}, "WL520GU-"},
+	{{BCM47XX_BOARD_BELKIN_F7D3301, "Belkin F7D3301"}, "F7D3301"},
+	{{BCM47XX_BOARD_BELKIN_F7D3302, "Belkin F7D3302"}, "F7D3302"},
+	{{BCM47XX_BOARD_BELKIN_F7D4301, "Belkin F7D4301"}, "F7D4301"},
+	{{BCM47XX_BOARD_BELKIN_F7D4302, "Belkin F7D4302"}, "F7D4302"},
+	{{BCM47XX_BOARD_BELKIN_F7D4401, "Belkin F7D4401"}, "F7D4401"},
+	{ {0}, NULL},
+};
+
+/* hardware_version, boardnum */
+static const
+struct bcm47xx_board_type_list2 bcm47xx_board_list_hw_version_num[] __initconst = {
+	{{BCM47XX_BOARD_MICROSOFT_MN700, "Microsoft MN-700"}, "WL500-", "mn700"},
+	{{BCM47XX_BOARD_ASUS_WL500G, "Asus WL500G"}, "WL500-", "asusX"},
+	{ {0}, NULL},
+};
+
+/* productid */
+static const
+struct bcm47xx_board_type_list1 bcm47xx_board_list_productid[] __initconst = {
+	{{BCM47XX_BOARD_ASUS_RTAC66U, "Asus RT-AC66U"}, "RT-AC66U"},
+	{{BCM47XX_BOARD_ASUS_RTN10, "Asus RT-N10"}, "RT-N10"},
+	{{BCM47XX_BOARD_ASUS_RTN10D, "Asus RT-N10D"}, "RT-N10D"},
+	{{BCM47XX_BOARD_ASUS_RTN15U, "Asus RT-N15U"}, "RT-N15U"},
+	{{BCM47XX_BOARD_ASUS_RTN16, "Asus RT-N16"}, "RT-N16"},
+	{{BCM47XX_BOARD_ASUS_RTN53, "Asus RT-N53"}, "RT-N53"},
+	{{BCM47XX_BOARD_ASUS_RTN66U, "Asus RT-N66U"}, "RT-N66U"},
+	{{BCM47XX_BOARD_ASUS_WL300G, "Asus WL300G"}, "WL300g"},
+	{{BCM47XX_BOARD_ASUS_WLHDD, "Asus WLHDD"}, "WLHDD"},
+	{ {0}, NULL},
+};
+
+/* ModelId */
+static const
+struct bcm47xx_board_type_list1 bcm47xx_board_list_ModelId[] __initconst = {
+	{{BCM47XX_BOARD_DELL_TM2300, "Dell TrueMobile 2300"}, "WX-5565"},
+	{{BCM47XX_BOARD_MOTOROLA_WE800G, "Motorola WE800G"}, "WE800G"},
+	{{BCM47XX_BOARD_MOTOROLA_WR850GP, "Motorola WR850GP"}, "WR850GP"},
+	{{BCM47XX_BOARD_MOTOROLA_WR850GV2V3, "Motorola WR850G"}, "WR850G"},
+	{ {0}, NULL},
+};
+
+/* melco_id or buf1falo_id */
+static const
+struct bcm47xx_board_type_list1 bcm47xx_board_list_melco_id[] __initconst = {
+	{{BCM47XX_BOARD_BUFFALO_WBR2_G54, "Buffalo WBR2-G54"}, "29bb0332"},
+	{{BCM47XX_BOARD_BUFFALO_WHR2_A54G54, "Buffalo WHR2-A54G54"}, "290441dd"},
+	{{BCM47XX_BOARD_BUFFALO_WHR_G125, "Buffalo WHR-G125"}, "32093"},
+	{{BCM47XX_BOARD_BUFFALO_WHR_G54S, "Buffalo WHR-G54S"}, "30182"},
+	{{BCM47XX_BOARD_BUFFALO_WHR_HP_G54, "Buffalo WHR-HP-G54"}, "30189"},
+	{{BCM47XX_BOARD_BUFFALO_WLA2_G54L, "Buffalo WLA2-G54L"}, "29129"},
+	{{BCM47XX_BOARD_BUFFALO_WZR_G300N, "Buffalo WZR-G300N"}, "31120"},
+	{{BCM47XX_BOARD_BUFFALO_WZR_RS_G54, "Buffalo WZR-RS-G54"}, "30083"},
+	{{BCM47XX_BOARD_BUFFALO_WZR_RS_G54HP, "Buffalo WZR-RS-G54HP"}, "30103"},
+	{ {0}, NULL},
+};
+
+/* boot_hw_model, boot_hw_ver */
+static const
+struct bcm47xx_board_type_list2 bcm47xx_board_list_boot_hw[] __initconst = {
+	/* like WRT160N v3.0 */
+	{{BCM47XX_BOARD_CISCO_M10V1, "Cisco M10"}, "M10", "1.0"},
+	/* like WRT310N v2.0 */
+	{{BCM47XX_BOARD_CISCO_M20V1, "Cisco M20"}, "M20", "1.0"},
+	{{BCM47XX_BOARD_LINKSYS_E900V1, "Linksys E900 V1"}, "E900", "1.0"},
+	/* like WRT160N v3.0 */
+	{{BCM47XX_BOARD_LINKSYS_E1000V1, "Linksys E1000 V1"}, "E100", "1.0"},
+	{{BCM47XX_BOARD_LINKSYS_E1000V2, "Linksys E1000 V2"}, "E1000", "2.0"},
+	{{BCM47XX_BOARD_LINKSYS_E1000V21, "Linksys E1000 V2.1"}, "E1000", "2.1"},
+	{{BCM47XX_BOARD_LINKSYS_E1200V2, "Linksys E1200 V2"}, "E1200", "2.0"},
+	{{BCM47XX_BOARD_LINKSYS_E2000V1, "Linksys E2000 V1"}, "Linksys E2000", "1.0"},
+	/* like WRT610N v2.0 */
+	{{BCM47XX_BOARD_LINKSYS_E3000V1, "Linksys E3000 V1"}, "E300", "1.0"},
+	{{BCM47XX_BOARD_LINKSYS_E3200V1, "Linksys E3200 V1"}, "E3200", "1.0"},
+	{{BCM47XX_BOARD_LINKSYS_E4200V1, "Linksys E4200 V1"}, "E4200", "1.0"},
+	{{BCM47XX_BOARD_LINKSYS_WRT150NV11, "Linksys WRT150N V1.1"}, "WRT150N", "1.1"},
+	{{BCM47XX_BOARD_LINKSYS_WRT150NV1, "Linksys WRT150N V1"}, "WRT150N", "1"},
+	{{BCM47XX_BOARD_LINKSYS_WRT160NV1, "Linksys WRT160N V1"}, "WRT160N", "1.0"},
+	{{BCM47XX_BOARD_LINKSYS_WRT160NV3, "Linksys WRT160N V3"}, "WRT160N", "3.0"},
+	{{BCM47XX_BOARD_LINKSYS_WRT300NV11, "Linksys WRT300N V1.1"}, "WRT300N", "1.1"},
+	{{BCM47XX_BOARD_LINKSYS_WRT310NV1, "Linksys WRT310N V1"}, "WRT310N", "1.0"},
+	{{BCM47XX_BOARD_LINKSYS_WRT310NV2, "Linksys WRT310N V2"}, "WRT310N", "2.0"},
+	{{BCM47XX_BOARD_LINKSYS_WRT320N_V1, "Linksys WRT320N V1"}, "WRT320N", "1.0"},
+	{{BCM47XX_BOARD_LINKSYS_WRT54G3GV2, "Linksys WRT54G3GV2-VF"}, "WRT54G3GV2-VF", "1.0"},
+	{{BCM47XX_BOARD_LINKSYS_WRT610NV1, "Linksys WRT610N V1"}, "WRT610N", "1.0"},
+	{{BCM47XX_BOARD_LINKSYS_WRT610NV2, "Linksys WRT610N V2"}, "WRT610N", "2.0"},
+	{ {0}, NULL},
+};
+
+/* board_id */
+static const
+struct bcm47xx_board_type_list1 bcm47xx_board_list_board_id[] __initconst = {
+	{{BCM47XX_BOARD_LUXUL_ABR_4400_V1, "Luxul ABR-4400 V1"}, "luxul_abr4400_v1"},
+	{{BCM47XX_BOARD_LUXUL_XAP_310_V1, "Luxul XAP-310 V1"}, "luxul_xap310_v1"},
+	{{BCM47XX_BOARD_LUXUL_XAP_1210_V1, "Luxul XAP-1210 V1"}, "luxul_xap1210_v1"},
+	{{BCM47XX_BOARD_LUXUL_XAP_1230_V1, "Luxul XAP-1230 V1"}, "luxul_xap1230_v1"},
+	{{BCM47XX_BOARD_LUXUL_XAP_1240_V1, "Luxul XAP-1240 V1"}, "luxul_xap1240_v1"},
+	{{BCM47XX_BOARD_LUXUL_XAP_1500_V1, "Luxul XAP-1500 V1"}, "luxul_xap1500_v1"},
+	{{BCM47XX_BOARD_LUXUL_XBR_4400_V1, "Luxul XBR-4400 V1"}, "luxul_xbr4400_v1"},
+	{{BCM47XX_BOARD_LUXUL_XVW_P30_V1, "Luxul XVW-P30 V1"}, "luxul_xvwp30_v1"},
+	{{BCM47XX_BOARD_LUXUL_XWR_600_V1, "Luxul XWR-600 V1"}, "luxul_xwr600_v1"},
+	{{BCM47XX_BOARD_LUXUL_XWR_1750_V1, "Luxul XWR-1750 V1"}, "luxul_xwr1750_v1"},
+	{{BCM47XX_BOARD_NETGEAR_R6200_V1, "Netgear R6200 V1"}, "U12H192T00_NETGEAR"},
+	{{BCM47XX_BOARD_NETGEAR_R6300_V1, "Netgear R6300 V1"}, "U12H218T00_NETGEAR"},
+	{{BCM47XX_BOARD_NETGEAR_WGR614V8, "Netgear WGR614 V8"}, "U12H072T00_NETGEAR"},
+	{{BCM47XX_BOARD_NETGEAR_WGR614V9, "Netgear WGR614 V9"}, "U12H094T00_NETGEAR"},
+	{{BCM47XX_BOARD_NETGEAR_WGR614_V10, "Netgear WGR614 V10"}, "U12H139T01_NETGEAR"},
+	{{BCM47XX_BOARD_NETGEAR_WN2500RP_V1, "Netgear WN2500RP V1"}, "U12H197T00_NETGEAR"},
+	{{BCM47XX_BOARD_NETGEAR_WN2500RP_V2, "Netgear WN2500RP V2"}, "U12H294T00_NETGEAR"},
+	{{BCM47XX_BOARD_NETGEAR_WNDR3300, "Netgear WNDR3300"}, "U12H093T00_NETGEAR"},
+	{{BCM47XX_BOARD_NETGEAR_WNDR3400V1, "Netgear WNDR3400 V1"}, "U12H155T00_NETGEAR"},
+	{{BCM47XX_BOARD_NETGEAR_WNDR3400V2, "Netgear WNDR3400 V2"}, "U12H187T00_NETGEAR"},
+	{{BCM47XX_BOARD_NETGEAR_WNDR3400_V3, "Netgear WNDR3400 V3"}, "U12H208T00_NETGEAR"},
+	{{BCM47XX_BOARD_NETGEAR_WNDR3400VCNA, "Netgear WNDR3400 Vcna"}, "U12H155T01_NETGEAR"},
+	{{BCM47XX_BOARD_NETGEAR_WNDR3700V3, "Netgear WNDR3700 V3"}, "U12H194T00_NETGEAR"},
+	{{BCM47XX_BOARD_NETGEAR_WNDR4000, "Netgear WNDR4000"}, "U12H181T00_NETGEAR"},
+	{{BCM47XX_BOARD_NETGEAR_WNDR4500V1, "Netgear WNDR4500 V1"}, "U12H189T00_NETGEAR"},
+	{{BCM47XX_BOARD_NETGEAR_WNDR4500V2, "Netgear WNDR4500 V2"}, "U12H224T00_NETGEAR"},
+	{{BCM47XX_BOARD_NETGEAR_WNR1000_V3, "Netgear WNR1000 V3"}, "U12H139T00_NETGEAR"},
+	{{BCM47XX_BOARD_NETGEAR_WNR1000_V3, "Netgear WNR1000 V3"}, "U12H139T50_NETGEAR"},
+	{{BCM47XX_BOARD_NETGEAR_WNR2000, "Netgear WNR2000"}, "U12H114T00_NETGEAR"},
+	{{BCM47XX_BOARD_NETGEAR_WNR3500L, "Netgear WNR3500L"}, "U12H136T99_NETGEAR"},
+	{{BCM47XX_BOARD_NETGEAR_WNR3500L_V2, "Netgear WNR3500L V2"}, "U12H172T00_NETGEAR"},
+	{{BCM47XX_BOARD_NETGEAR_WNR3500U, "Netgear WNR3500U"}, "U12H136T00_NETGEAR"},
+	{{BCM47XX_BOARD_NETGEAR_WNR3500V2, "Netgear WNR3500 V2"}, "U12H127T00_NETGEAR"},
+	{{BCM47XX_BOARD_NETGEAR_WNR3500V2VC, "Netgear WNR3500 V2vc"}, "U12H127T70_NETGEAR"},
+	{{BCM47XX_BOARD_NETGEAR_WNR834BV2, "Netgear WNR834B V2"}, "U12H081T00_NETGEAR"},
+	{ {0}, NULL},
+};
+
+/* boardtype, boardnum, boardrev */
+static const
+struct bcm47xx_board_type_list3 bcm47xx_board_list_board[] __initconst = {
+	{{BCM47XX_BOARD_HUAWEI_E970, "Huawei E970"}, "0x048e", "0x5347", "0x11"},
+	{{BCM47XX_BOARD_PHICOMM_M1, "Phicomm M1"}, "0x0590", "80", "0x1104"},
+	{{BCM47XX_BOARD_ZTE_H218N, "ZTE H218N"}, "0x053d", "1234", "0x1305"},
+	{{BCM47XX_BOARD_NETGEAR_WNR3500L, "Netgear WNR3500L"}, "0x04CF", "3500", "02"},
+	{{BCM47XX_BOARD_NETGEAR_WNR3500L_V2, "Netgear WNR3500L V2"}, "0x052b", "3500L", "02"},
+	{{BCM47XX_BOARD_LINKSYS_WRT54G_TYPE_0101, "Linksys WRT54G/GS/GL"}, "0x0101", "42", "0x10"},
+	{{BCM47XX_BOARD_LINKSYS_WRT54G_TYPE_0467, "Linksys WRT54G/GS/GL"}, "0x0467", "42", "0x10"},
+	{{BCM47XX_BOARD_LINKSYS_WRT54G_TYPE_0708, "Linksys WRT54G/GS/GL"}, "0x0708", "42", "0x10"},
+	{ {0}, NULL},
+};
+
+/* boardtype, boardrev */
+static const
+struct bcm47xx_board_type_list2 bcm47xx_board_list_board_type_rev[] __initconst = {
+	{{BCM47XX_BOARD_SIEMENS_SE505V2, "Siemens SE505 V2"}, "0x0101", "0x10"},
+	{ {0}, NULL},
+};
+
+/*
+ * Some devices don't use any common NVRAM entry for identification and they
+ * have only one model specific variable.
+ * They don't deserve own arrays, let's group them there using key-value array.
+ */
+static const
+struct bcm47xx_board_type_list2 bcm47xx_board_list_key_value[] __initconst = {
+	{{BCM47XX_BOARD_ASUS_WL700GE, "Asus WL700"}, "model_no", "WL700"},
+	{{BCM47XX_BOARD_LINKSYS_WRT300N_V1, "Linksys WRT300N V1"}, "router_name", "WRT300N"},
+	{{BCM47XX_BOARD_LINKSYS_WRT600N_V11, "Linksys WRT600N V1.1"}, "Model_Name", "WRT600N"},
+	{{BCM47XX_BOARD_LINKSYS_WRTSL54GS, "Linksys WRTSL54GS"}, "machine_name", "WRTSL54GS"},
+	{ {0}, NULL},
+};
+
+static const
+struct bcm47xx_board_type bcm47xx_board_unknown[] __initconst = {
+	{BCM47XX_BOARD_UNKNOWN, "Unknown Board"},
+};
+
+static struct bcm47xx_board_store bcm47xx_board = {BCM47XX_BOARD_NO, "Unknown Board"};
+
+static __init const struct bcm47xx_board_type *bcm47xx_board_get_nvram(void)
+{
+	char buf1[30];
+	char buf2[30];
+	char buf3[30];
+	const struct bcm47xx_board_type_list1 *e1;
+	const struct bcm47xx_board_type_list2 *e2;
+	const struct bcm47xx_board_type_list3 *e3;
+
+	if (bcm47xx_nvram_getenv("model_name", buf1, sizeof(buf1)) >= 0) {
+		for (e1 = bcm47xx_board_list_model_name; e1->value1; e1++) {
+			if (!strcmp(buf1, e1->value1))
+				return &e1->board;
+		}
+	}
+
+	if (bcm47xx_nvram_getenv("hardware_version", buf1, sizeof(buf1)) >= 0) {
+		for (e1 = bcm47xx_board_list_hardware_version; e1->value1; e1++) {
+			if (strstarts(buf1, e1->value1))
+				return &e1->board;
+		}
+	}
+
+	if (bcm47xx_nvram_getenv("hardware_version", buf1, sizeof(buf1)) >= 0 &&
+	    bcm47xx_nvram_getenv("boardnum", buf2, sizeof(buf2)) >= 0) {
+		for (e2 = bcm47xx_board_list_hw_version_num; e2->value1; e2++) {
+			if (!strstarts(buf1, e2->value1) &&
+			    !strcmp(buf2, e2->value2))
+				return &e2->board;
+		}
+	}
+
+	if (bcm47xx_nvram_getenv("productid", buf1, sizeof(buf1)) >= 0) {
+		for (e1 = bcm47xx_board_list_productid; e1->value1; e1++) {
+			if (!strcmp(buf1, e1->value1))
+				return &e1->board;
+		}
+	}
+
+	if (bcm47xx_nvram_getenv("ModelId", buf1, sizeof(buf1)) >= 0) {
+		for (e1 = bcm47xx_board_list_ModelId; e1->value1; e1++) {
+			if (!strcmp(buf1, e1->value1))
+				return &e1->board;
+		}
+	}
+
+	if (bcm47xx_nvram_getenv("melco_id", buf1, sizeof(buf1)) >= 0 ||
+	    bcm47xx_nvram_getenv("buf1falo_id", buf1, sizeof(buf1)) >= 0) {
+		/* buffalo hardware, check id for specific hardware matches */
+		for (e1 = bcm47xx_board_list_melco_id; e1->value1; e1++) {
+			if (!strcmp(buf1, e1->value1))
+				return &e1->board;
+		}
+	}
+
+	if (bcm47xx_nvram_getenv("boot_hw_model", buf1, sizeof(buf1)) >= 0 &&
+	    bcm47xx_nvram_getenv("boot_hw_ver", buf2, sizeof(buf2)) >= 0) {
+		for (e2 = bcm47xx_board_list_boot_hw; e2->value1; e2++) {
+			if (!strcmp(buf1, e2->value1) &&
+			    !strcmp(buf2, e2->value2))
+				return &e2->board;
+		}
+	}
+
+	if (bcm47xx_nvram_getenv("board_id", buf1, sizeof(buf1)) >= 0) {
+		for (e1 = bcm47xx_board_list_board_id; e1->value1; e1++) {
+			if (!strcmp(buf1, e1->value1))
+				return &e1->board;
+		}
+	}
+
+	if (bcm47xx_nvram_getenv("boardtype", buf1, sizeof(buf1)) >= 0 &&
+	    bcm47xx_nvram_getenv("boardnum", buf2, sizeof(buf2)) >= 0 &&
+	    bcm47xx_nvram_getenv("boardrev", buf3, sizeof(buf3)) >= 0) {
+		for (e3 = bcm47xx_board_list_board; e3->value1; e3++) {
+			if (!strcmp(buf1, e3->value1) &&
+			    !strcmp(buf2, e3->value2) &&
+			    !strcmp(buf3, e3->value3))
+				return &e3->board;
+		}
+	}
+
+	if (bcm47xx_nvram_getenv("boardtype", buf1, sizeof(buf1)) >= 0 &&
+	    bcm47xx_nvram_getenv("boardrev", buf2, sizeof(buf2)) >= 0 &&
+	    bcm47xx_nvram_getenv("boardnum", buf3, sizeof(buf3)) ==  -ENOENT) {
+		for (e2 = bcm47xx_board_list_board_type_rev; e2->value1; e2++) {
+			if (!strcmp(buf1, e2->value1) &&
+			    !strcmp(buf2, e2->value2))
+				return &e2->board;
+		}
+	}
+
+	for (e2 = bcm47xx_board_list_key_value; e2->value1; e2++) {
+		if (bcm47xx_nvram_getenv(e2->value1, buf1, sizeof(buf1)) >= 0) {
+			if (!strcmp(buf1, e2->value2))
+				return &e2->board;
+		}
+	}
+
+	return bcm47xx_board_unknown;
+}
+
+void __init bcm47xx_board_detect(void)
+{
+	int err;
+	char buf[10];
+	const struct bcm47xx_board_type *board_detected;
+
+	if (bcm47xx_board.board != BCM47XX_BOARD_NO)
+		return;
+
+	/* check if the nvram is available */
+	err = bcm47xx_nvram_getenv("boardtype", buf, sizeof(buf));
+
+	/* init of nvram failed, probably too early now */
+	if (err == -ENXIO)
+		return;
+
+	board_detected = bcm47xx_board_get_nvram();
+	bcm47xx_board.board = board_detected->board;
+	strscpy(bcm47xx_board.name, board_detected->name,
+		BCM47XX_BOARD_MAX_NAME);
+}
+
+enum bcm47xx_board bcm47xx_board_get(void)
+{
+	return bcm47xx_board.board;
+}
+EXPORT_SYMBOL(bcm47xx_board_get);
+
+const char *bcm47xx_board_get_name(void)
+{
+	return bcm47xx_board.name;
+}
+EXPORT_SYMBOL(bcm47xx_board_get_name);
diff --git a/arch/mips/bcm47xx/buttons.c b/arch/mips/bcm47xx/buttons.c
new file mode 100644
index 000000000..38e4a9cbc
--- /dev/null
+++ b/arch/mips/bcm47xx/buttons.c
@@ -0,0 +1,772 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "bcm47xx_private.h"
+
+#include <linux/input.h>
+#include <linux/gpio_keys.h>
+#include <linux/interrupt.h>
+#include <bcm47xx_board.h>
+#include <bcm47xx.h>
+
+/**************************************************
+ * Database
+ **************************************************/
+
+#define BCM47XX_GPIO_KEY(_gpio, _code)					\
+	{								\
+		.code		= _code,				\
+		.gpio		= _gpio,				\
+		.active_low	= 1,					\
+	}
+
+#define BCM47XX_GPIO_KEY_H(_gpio, _code)				\
+	{								\
+		.code		= _code,				\
+		.gpio		= _gpio,				\
+	}
+
+/* Asus */
+
+static const struct gpio_keys_button
+bcm47xx_buttons_asus_rtn10u[] __initconst = {
+	BCM47XX_GPIO_KEY(20, KEY_WPS_BUTTON),
+	BCM47XX_GPIO_KEY(21, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_asus_rtn12[] __initconst = {
+	BCM47XX_GPIO_KEY(0, KEY_WPS_BUTTON),
+	BCM47XX_GPIO_KEY(1, KEY_RESTART),
+	BCM47XX_GPIO_KEY(4, BTN_0), /* Router mode */
+	BCM47XX_GPIO_KEY(5, BTN_1), /* Repeater mode */
+	BCM47XX_GPIO_KEY(6, BTN_2), /* AP mode */
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_asus_rtn16[] __initconst = {
+	BCM47XX_GPIO_KEY(6, KEY_WPS_BUTTON),
+	BCM47XX_GPIO_KEY(8, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_asus_rtn66u[] __initconst = {
+	BCM47XX_GPIO_KEY(4, KEY_WPS_BUTTON),
+	BCM47XX_GPIO_KEY(9, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_asus_wl300g[] __initconst = {
+	BCM47XX_GPIO_KEY(6, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_asus_wl320ge[] __initconst = {
+	BCM47XX_GPIO_KEY(6, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_asus_wl330ge[] __initconst = {
+	BCM47XX_GPIO_KEY(2, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_asus_wl500g[] __initconst = {
+	BCM47XX_GPIO_KEY(6, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_asus_wl500gd[] __initconst = {
+	BCM47XX_GPIO_KEY(6, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_asus_wl500gpv1[] __initconst = {
+	BCM47XX_GPIO_KEY(0, KEY_RESTART),
+	BCM47XX_GPIO_KEY(4, KEY_WPS_BUTTON),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_asus_wl500gpv2[] __initconst = {
+	BCM47XX_GPIO_KEY(2, KEY_RESTART),
+	BCM47XX_GPIO_KEY(3, KEY_WPS_BUTTON),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_asus_wl500w[] __initconst = {
+	BCM47XX_GPIO_KEY_H(6, KEY_RESTART),
+	BCM47XX_GPIO_KEY_H(7, KEY_WPS_BUTTON),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_asus_wl520gc[] __initconst = {
+	BCM47XX_GPIO_KEY(2, KEY_RESTART),
+	BCM47XX_GPIO_KEY(3, KEY_WPS_BUTTON),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_asus_wl520gu[] __initconst = {
+	BCM47XX_GPIO_KEY(2, KEY_RESTART),
+	BCM47XX_GPIO_KEY(3, KEY_WPS_BUTTON),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_asus_wl700ge[] __initconst = {
+	BCM47XX_GPIO_KEY(0, KEY_POWER), /* Hard disk power switch */
+	BCM47XX_GPIO_KEY(4, KEY_WPS_BUTTON), /* EZSetup */
+	BCM47XX_GPIO_KEY(6, KEY_COPY), /* Copy data from USB to internal disk */
+	BCM47XX_GPIO_KEY(7, KEY_RESTART), /* Hard reset */
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_asus_wlhdd[] __initconst = {
+	BCM47XX_GPIO_KEY(6, KEY_RESTART),
+};
+
+/* Huawei */
+
+static const struct gpio_keys_button
+bcm47xx_buttons_huawei_e970[] __initconst = {
+	BCM47XX_GPIO_KEY(6, KEY_RESTART),
+};
+
+/* Belkin */
+
+static const struct gpio_keys_button
+bcm47xx_buttons_belkin_f7d4301[] __initconst = {
+	BCM47XX_GPIO_KEY(6, KEY_RESTART),
+	BCM47XX_GPIO_KEY(8, KEY_WPS_BUTTON),
+};
+
+/* Buffalo */
+
+static const struct gpio_keys_button
+bcm47xx_buttons_buffalo_whr2_a54g54[] __initconst = {
+	BCM47XX_GPIO_KEY(4, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_buffalo_whr_g125[] __initconst = {
+	BCM47XX_GPIO_KEY(0, KEY_WPS_BUTTON),
+	BCM47XX_GPIO_KEY(4, KEY_RESTART),
+	BCM47XX_GPIO_KEY(5, BTN_0), /* Router / AP mode swtich */
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_buffalo_whr_g54s[] __initconst = {
+	BCM47XX_GPIO_KEY(0, KEY_WPS_BUTTON),
+	BCM47XX_GPIO_KEY_H(4, KEY_RESTART),
+	BCM47XX_GPIO_KEY(5, BTN_0), /* Router / AP mode swtich */
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_buffalo_whr_hp_g54[] __initconst = {
+	BCM47XX_GPIO_KEY(0, KEY_WPS_BUTTON),
+	BCM47XX_GPIO_KEY(4, KEY_RESTART),
+	BCM47XX_GPIO_KEY(5, BTN_0), /* Router / AP mode swtich */
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_buffalo_wzr_g300n[] __initconst = {
+	BCM47XX_GPIO_KEY(4, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_buffalo_wzr_rs_g54[] __initconst = {
+	BCM47XX_GPIO_KEY(0, KEY_WPS_BUTTON),
+	BCM47XX_GPIO_KEY(4, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_buffalo_wzr_rs_g54hp[] __initconst = {
+	BCM47XX_GPIO_KEY(0, KEY_WPS_BUTTON),
+	BCM47XX_GPIO_KEY(4, KEY_RESTART),
+};
+
+/* Dell */
+
+static const struct gpio_keys_button
+bcm47xx_buttons_dell_tm2300[] __initconst = {
+	BCM47XX_GPIO_KEY(0, KEY_RESTART),
+};
+
+/* D-Link */
+
+static const struct gpio_keys_button
+bcm47xx_buttons_dlink_dir130[] __initconst = {
+	BCM47XX_GPIO_KEY(3, KEY_RESTART),
+	BCM47XX_GPIO_KEY(7, KEY_UNKNOWN),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_dlink_dir330[] __initconst = {
+	BCM47XX_GPIO_KEY(3, KEY_RESTART),
+	BCM47XX_GPIO_KEY(7, KEY_UNKNOWN),
+};
+
+/* Linksys */
+
+static const struct gpio_keys_button
+bcm47xx_buttons_linksys_e1000v1[] __initconst = {
+	BCM47XX_GPIO_KEY(5, KEY_WPS_BUTTON),
+	BCM47XX_GPIO_KEY(6, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_linksys_e1000v21[] __initconst = {
+	BCM47XX_GPIO_KEY(9, KEY_WPS_BUTTON),
+	BCM47XX_GPIO_KEY(10, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_linksys_e2000v1[] __initconst = {
+	BCM47XX_GPIO_KEY(5, KEY_WPS_BUTTON),
+	BCM47XX_GPIO_KEY(8, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_linksys_e3000v1[] __initconst = {
+	BCM47XX_GPIO_KEY(4, KEY_WPS_BUTTON),
+	BCM47XX_GPIO_KEY(6, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_linksys_e3200v1[] __initconst = {
+	BCM47XX_GPIO_KEY(5, KEY_RESTART),
+	BCM47XX_GPIO_KEY(8, KEY_WPS_BUTTON),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_linksys_e4200v1[] __initconst = {
+	BCM47XX_GPIO_KEY(4, KEY_WPS_BUTTON),
+	BCM47XX_GPIO_KEY(6, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_linksys_wrt150nv1[] __initconst = {
+	BCM47XX_GPIO_KEY(4, KEY_WPS_BUTTON),
+	BCM47XX_GPIO_KEY(6, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_linksys_wrt150nv11[] __initconst = {
+	BCM47XX_GPIO_KEY(4, KEY_WPS_BUTTON),
+	BCM47XX_GPIO_KEY(6, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_linksys_wrt160nv1[] __initconst = {
+	BCM47XX_GPIO_KEY(4, KEY_WPS_BUTTON),
+	BCM47XX_GPIO_KEY(6, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_linksys_wrt160nv3[] __initconst = {
+	BCM47XX_GPIO_KEY(5, KEY_WPS_BUTTON),
+	BCM47XX_GPIO_KEY(6, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_linksys_wrt300n_v1[] __initconst = {
+	BCM47XX_GPIO_KEY(4, KEY_WPS_BUTTON),
+	BCM47XX_GPIO_KEY(6, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_linksys_wrt300nv11[] __initconst = {
+	BCM47XX_GPIO_KEY(4, KEY_UNKNOWN),
+	BCM47XX_GPIO_KEY(6, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_linksys_wrt310nv1[] __initconst = {
+	BCM47XX_GPIO_KEY(6, KEY_RESTART),
+	BCM47XX_GPIO_KEY(8, KEY_UNKNOWN),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_linksys_wrt310n_v2[] __initconst = {
+	BCM47XX_GPIO_KEY(5, KEY_WPS_BUTTON),
+	BCM47XX_GPIO_KEY(6, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_linksys_wrt320n_v1[] __initconst = {
+	BCM47XX_GPIO_KEY(5, KEY_WPS_BUTTON),
+	BCM47XX_GPIO_KEY(8, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_linksys_wrt54g3gv2[] __initconst = {
+	BCM47XX_GPIO_KEY(5, KEY_WIMAX),
+	BCM47XX_GPIO_KEY(6, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_linksys_wrt54g_generic[] __initconst = {
+	BCM47XX_GPIO_KEY(4, KEY_WPS_BUTTON),
+	BCM47XX_GPIO_KEY(6, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_linksys_wrt610nv1[] __initconst = {
+	BCM47XX_GPIO_KEY(6, KEY_RESTART),
+	BCM47XX_GPIO_KEY(8, KEY_WPS_BUTTON),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_linksys_wrt610nv2[] __initconst = {
+	BCM47XX_GPIO_KEY(4, KEY_WPS_BUTTON),
+	BCM47XX_GPIO_KEY(6, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_linksys_wrtsl54gs[] __initconst = {
+	BCM47XX_GPIO_KEY(4, KEY_WPS_BUTTON),
+	BCM47XX_GPIO_KEY(6, KEY_RESTART),
+};
+
+/* Luxul */
+
+static const struct gpio_keys_button
+bcm47xx_buttons_luxul_abr_4400_v1[] = {
+	BCM47XX_GPIO_KEY(14, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_luxul_xap_310_v1[] = {
+	BCM47XX_GPIO_KEY(20, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_luxul_xap_1210_v1[] = {
+	BCM47XX_GPIO_KEY(8, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_luxul_xap_1230_v1[] = {
+	BCM47XX_GPIO_KEY(8, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_luxul_xap_1240_v1[] = {
+	BCM47XX_GPIO_KEY(8, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_luxul_xap_1500_v1[] = {
+	BCM47XX_GPIO_KEY(14, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_luxul_xbr_4400_v1[] = {
+	BCM47XX_GPIO_KEY(14, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_luxul_xvw_p30_v1[] = {
+	BCM47XX_GPIO_KEY(20, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_luxul_xwr_600_v1[] = {
+	BCM47XX_GPIO_KEY(8, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_luxul_xwr_1750_v1[] = {
+	BCM47XX_GPIO_KEY(14, KEY_RESTART),
+};
+
+/* Microsoft */
+
+static const struct gpio_keys_button
+bcm47xx_buttons_microsoft_nm700[] __initconst = {
+	BCM47XX_GPIO_KEY(7, KEY_RESTART),
+};
+
+/* Motorola */
+
+static const struct gpio_keys_button
+bcm47xx_buttons_motorola_we800g[] __initconst = {
+	BCM47XX_GPIO_KEY(0, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_motorola_wr850gp[] __initconst = {
+	BCM47XX_GPIO_KEY(5, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_motorola_wr850gv2v3[] __initconst = {
+	BCM47XX_GPIO_KEY(5, KEY_RESTART),
+};
+
+/* Netgear */
+
+static const struct gpio_keys_button
+bcm47xx_buttons_netgear_r6200_v1[] __initconst = {
+	BCM47XX_GPIO_KEY(2, KEY_RFKILL),
+	BCM47XX_GPIO_KEY(3, KEY_RESTART),
+	BCM47XX_GPIO_KEY(4, KEY_WPS_BUTTON),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_netgear_r6300_v1[] __initconst = {
+	BCM47XX_GPIO_KEY(6, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_netgear_wn2500rp_v1[] __initconst = {
+	BCM47XX_GPIO_KEY(12, KEY_RESTART),
+	BCM47XX_GPIO_KEY(31, KEY_WPS_BUTTON),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_netgear_wndr3400v1[] __initconst = {
+	BCM47XX_GPIO_KEY(4, KEY_RESTART),
+	BCM47XX_GPIO_KEY(6, KEY_WPS_BUTTON),
+	BCM47XX_GPIO_KEY(8, KEY_RFKILL),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_netgear_wndr3400_v3[] __initconst = {
+	BCM47XX_GPIO_KEY(12, KEY_RESTART),
+	BCM47XX_GPIO_KEY(23, KEY_WPS_BUTTON),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_netgear_wndr3700v3[] __initconst = {
+	BCM47XX_GPIO_KEY(2, KEY_RFKILL),
+	BCM47XX_GPIO_KEY(3, KEY_RESTART),
+	BCM47XX_GPIO_KEY(4, KEY_WPS_BUTTON),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_netgear_wndr4500v1[] __initconst = {
+	BCM47XX_GPIO_KEY(4, KEY_WPS_BUTTON),
+	BCM47XX_GPIO_KEY(5, KEY_RFKILL),
+	BCM47XX_GPIO_KEY(6, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_netgear_wnr1000_v3[] __initconst = {
+	BCM47XX_GPIO_KEY(2, KEY_WPS_BUTTON),
+	BCM47XX_GPIO_KEY(3, KEY_RESTART),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_netgear_wnr3500lv1[] __initconst = {
+	BCM47XX_GPIO_KEY(4, KEY_RESTART),
+	BCM47XX_GPIO_KEY(6, KEY_WPS_BUTTON),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_netgear_wnr3500lv2[] __initconst = {
+	BCM47XX_GPIO_KEY(4, KEY_RESTART),
+	BCM47XX_GPIO_KEY(6, KEY_WPS_BUTTON),
+	BCM47XX_GPIO_KEY(8, KEY_RFKILL),
+};
+
+static const struct gpio_keys_button
+bcm47xx_buttons_netgear_wnr834bv2[] __initconst = {
+	BCM47XX_GPIO_KEY(6, KEY_RESTART),
+};
+
+/* SimpleTech */
+
+static const struct gpio_keys_button
+bcm47xx_buttons_simpletech_simpleshare[] __initconst = {
+	BCM47XX_GPIO_KEY(0, KEY_RESTART),
+};
+
+/**************************************************
+ * Init
+ **************************************************/
+
+static struct gpio_keys_platform_data bcm47xx_button_pdata;
+
+static struct platform_device bcm47xx_buttons_gpio_keys = {
+	.name = "gpio-keys",
+	.dev = {
+		.platform_data = &bcm47xx_button_pdata,
+	}
+};
+
+/* Copy data from __initconst */
+static int __init bcm47xx_buttons_copy(const struct gpio_keys_button *buttons,
+				       size_t nbuttons)
+{
+	size_t size = nbuttons * sizeof(*buttons);
+
+	bcm47xx_button_pdata.buttons = kmemdup(buttons, size, GFP_KERNEL);
+	if (!bcm47xx_button_pdata.buttons)
+		return -ENOMEM;
+	bcm47xx_button_pdata.nbuttons = nbuttons;
+
+	return 0;
+}
+
+#define bcm47xx_copy_bdata(dev_buttons)					\
+	bcm47xx_buttons_copy(dev_buttons, ARRAY_SIZE(dev_buttons));
+
+int __init bcm47xx_buttons_register(void)
+{
+	enum bcm47xx_board board = bcm47xx_board_get();
+	int err;
+
+	switch (board) {
+	case BCM47XX_BOARD_ASUS_RTN10U:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_asus_rtn10u);
+		break;
+	case BCM47XX_BOARD_ASUS_RTN12:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_asus_rtn12);
+		break;
+	case BCM47XX_BOARD_ASUS_RTN16:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_asus_rtn16);
+		break;
+	case BCM47XX_BOARD_ASUS_RTN66U:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_asus_rtn66u);
+		break;
+	case BCM47XX_BOARD_ASUS_WL300G:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_asus_wl300g);
+		break;
+	case BCM47XX_BOARD_ASUS_WL320GE:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_asus_wl320ge);
+		break;
+	case BCM47XX_BOARD_ASUS_WL330GE:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_asus_wl330ge);
+		break;
+	case BCM47XX_BOARD_ASUS_WL500G:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_asus_wl500g);
+		break;
+	case BCM47XX_BOARD_ASUS_WL500GD:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_asus_wl500gd);
+		break;
+	case BCM47XX_BOARD_ASUS_WL500GPV1:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_asus_wl500gpv1);
+		break;
+	case BCM47XX_BOARD_ASUS_WL500GPV2:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_asus_wl500gpv2);
+		break;
+	case BCM47XX_BOARD_ASUS_WL500W:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_asus_wl500w);
+		break;
+	case BCM47XX_BOARD_ASUS_WL520GC:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_asus_wl520gc);
+		break;
+	case BCM47XX_BOARD_ASUS_WL520GU:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_asus_wl520gu);
+		break;
+	case BCM47XX_BOARD_ASUS_WL700GE:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_asus_wl700ge);
+		break;
+	case BCM47XX_BOARD_ASUS_WLHDD:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_asus_wlhdd);
+		break;
+
+	case BCM47XX_BOARD_BELKIN_F7D3301:
+	case BCM47XX_BOARD_BELKIN_F7D3302:
+	case BCM47XX_BOARD_BELKIN_F7D4301:
+	case BCM47XX_BOARD_BELKIN_F7D4302:
+	case BCM47XX_BOARD_BELKIN_F7D4401:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_belkin_f7d4301);
+		break;
+
+	case BCM47XX_BOARD_BUFFALO_WHR2_A54G54:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_buffalo_whr2_a54g54);
+		break;
+	case BCM47XX_BOARD_BUFFALO_WHR_G125:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_buffalo_whr_g125);
+		break;
+	case BCM47XX_BOARD_BUFFALO_WHR_G54S:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_buffalo_whr_g54s);
+		break;
+	case BCM47XX_BOARD_BUFFALO_WHR_HP_G54:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_buffalo_whr_hp_g54);
+		break;
+	case BCM47XX_BOARD_BUFFALO_WZR_G300N:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_buffalo_wzr_g300n);
+		break;
+	case BCM47XX_BOARD_BUFFALO_WZR_RS_G54:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_buffalo_wzr_rs_g54);
+		break;
+	case BCM47XX_BOARD_BUFFALO_WZR_RS_G54HP:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_buffalo_wzr_rs_g54hp);
+		break;
+
+	case BCM47XX_BOARD_DELL_TM2300:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_dell_tm2300);
+		break;
+
+	case BCM47XX_BOARD_DLINK_DIR130:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_dlink_dir130);
+		break;
+	case BCM47XX_BOARD_DLINK_DIR330:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_dlink_dir330);
+		break;
+
+	case BCM47XX_BOARD_HUAWEI_E970:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_huawei_e970);
+		break;
+
+	case BCM47XX_BOARD_LINKSYS_E1000V1:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_linksys_e1000v1);
+		break;
+	case BCM47XX_BOARD_LINKSYS_E1000V21:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_linksys_e1000v21);
+		break;
+	case BCM47XX_BOARD_LINKSYS_E2000V1:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_linksys_e2000v1);
+		break;
+	case BCM47XX_BOARD_LINKSYS_E3000V1:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_linksys_e3000v1);
+		break;
+	case BCM47XX_BOARD_LINKSYS_E3200V1:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_linksys_e3200v1);
+		break;
+	case BCM47XX_BOARD_LINKSYS_E4200V1:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_linksys_e4200v1);
+		break;
+	case BCM47XX_BOARD_LINKSYS_WRT150NV1:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_linksys_wrt150nv1);
+		break;
+	case BCM47XX_BOARD_LINKSYS_WRT150NV11:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_linksys_wrt150nv11);
+		break;
+	case BCM47XX_BOARD_LINKSYS_WRT160NV1:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_linksys_wrt160nv1);
+		break;
+	case BCM47XX_BOARD_LINKSYS_WRT160NV3:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_linksys_wrt160nv3);
+		break;
+	case BCM47XX_BOARD_LINKSYS_WRT300N_V1:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_linksys_wrt300n_v1);
+		break;
+	case BCM47XX_BOARD_LINKSYS_WRT300NV11:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_linksys_wrt300nv11);
+		break;
+	case BCM47XX_BOARD_LINKSYS_WRT310NV1:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_linksys_wrt310nv1);
+		break;
+	case BCM47XX_BOARD_LINKSYS_WRT310NV2:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_linksys_wrt310n_v2);
+		break;
+	case BCM47XX_BOARD_LINKSYS_WRT320N_V1:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_linksys_wrt320n_v1);
+		break;
+	case BCM47XX_BOARD_LINKSYS_WRT54G3GV2:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_linksys_wrt54g3gv2);
+		break;
+	case BCM47XX_BOARD_LINKSYS_WRT54G_TYPE_0101:
+	case BCM47XX_BOARD_LINKSYS_WRT54G_TYPE_0467:
+	case BCM47XX_BOARD_LINKSYS_WRT54G_TYPE_0708:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_linksys_wrt54g_generic);
+		break;
+	case BCM47XX_BOARD_LINKSYS_WRT610NV1:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_linksys_wrt610nv1);
+		break;
+	case BCM47XX_BOARD_LINKSYS_WRT610NV2:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_linksys_wrt610nv2);
+		break;
+	case BCM47XX_BOARD_LINKSYS_WRTSL54GS:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_linksys_wrtsl54gs);
+		break;
+
+	case BCM47XX_BOARD_LUXUL_ABR_4400_V1:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_luxul_abr_4400_v1);
+		break;
+	case BCM47XX_BOARD_LUXUL_XAP_310_V1:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_luxul_xap_310_v1);
+		break;
+	case BCM47XX_BOARD_LUXUL_XAP_1210_V1:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_luxul_xap_1210_v1);
+		break;
+	case BCM47XX_BOARD_LUXUL_XAP_1230_V1:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_luxul_xap_1230_v1);
+		break;
+	case BCM47XX_BOARD_LUXUL_XAP_1240_V1:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_luxul_xap_1240_v1);
+		break;
+	case BCM47XX_BOARD_LUXUL_XAP_1500_V1:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_luxul_xap_1500_v1);
+		break;
+	case BCM47XX_BOARD_LUXUL_XBR_4400_V1:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_luxul_xbr_4400_v1);
+		break;
+	case BCM47XX_BOARD_LUXUL_XVW_P30_V1:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_luxul_xvw_p30_v1);
+		break;
+	case BCM47XX_BOARD_LUXUL_XWR_600_V1:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_luxul_xwr_600_v1);
+		break;
+	case BCM47XX_BOARD_LUXUL_XWR_1750_V1:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_luxul_xwr_1750_v1);
+		break;
+
+	case BCM47XX_BOARD_MICROSOFT_MN700:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_microsoft_nm700);
+		break;
+
+	case BCM47XX_BOARD_MOTOROLA_WE800G:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_motorola_we800g);
+		break;
+	case BCM47XX_BOARD_MOTOROLA_WR850GP:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_motorola_wr850gp);
+		break;
+	case BCM47XX_BOARD_MOTOROLA_WR850GV2V3:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_motorola_wr850gv2v3);
+		break;
+
+	case BCM47XX_BOARD_NETGEAR_R6200_V1:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_netgear_r6200_v1);
+		break;
+	case BCM47XX_BOARD_NETGEAR_R6300_V1:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_netgear_r6300_v1);
+		break;
+	case BCM47XX_BOARD_NETGEAR_WN2500RP_V1:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_netgear_wn2500rp_v1);
+		break;
+	case BCM47XX_BOARD_NETGEAR_WNDR3400V1:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_netgear_wndr3400v1);
+		break;
+	case BCM47XX_BOARD_NETGEAR_WNDR3400_V3:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_netgear_wndr3400_v3);
+		break;
+	case BCM47XX_BOARD_NETGEAR_WNDR3700V3:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_netgear_wndr3700v3);
+		break;
+	case BCM47XX_BOARD_NETGEAR_WNDR4500V1:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_netgear_wndr4500v1);
+		break;
+	case BCM47XX_BOARD_NETGEAR_WNR1000_V3:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_netgear_wnr1000_v3);
+		break;
+	case BCM47XX_BOARD_NETGEAR_WNR3500L:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_netgear_wnr3500lv1);
+		break;
+	case BCM47XX_BOARD_NETGEAR_WNR3500L_V2:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_netgear_wnr3500lv2);
+		break;
+	case BCM47XX_BOARD_NETGEAR_WNR834BV2:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_netgear_wnr834bv2);
+		break;
+
+	case BCM47XX_BOARD_SIMPLETECH_SIMPLESHARE:
+		err = bcm47xx_copy_bdata(bcm47xx_buttons_simpletech_simpleshare);
+		break;
+
+	default:
+		pr_debug("No buttons configuration found for this device\n");
+		return -ENOTSUPP;
+	}
+
+	if (err)
+		return -ENOMEM;
+
+	err = platform_device_register(&bcm47xx_buttons_gpio_keys);
+	if (err) {
+		pr_err("Failed to register platform device: %d\n", err);
+		return err;
+	}
+
+	return 0;
+}
diff --git a/arch/mips/bcm47xx/irq.c b/arch/mips/bcm47xx/irq.c
new file mode 100644
index 000000000..21b4497f0
--- /dev/null
+++ b/arch/mips/bcm47xx/irq.c
@@ -0,0 +1,98 @@
+/*
+ *  Copyright (C) 2004 Florian Schirmer <jolt@tuxbox.org>
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include "bcm47xx_private.h"
+
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <asm/setup.h>
+#include <asm/irq_cpu.h>
+#include <bcm47xx.h>
+
+asmlinkage void plat_irq_dispatch(void)
+{
+	u32 cause;
+
+	cause = read_c0_cause() & read_c0_status() & CAUSEF_IP;
+
+	clear_c0_status(cause);
+
+	if (cause & CAUSEF_IP7)
+		do_IRQ(7);
+	if (cause & CAUSEF_IP2)
+		do_IRQ(2);
+	if (cause & CAUSEF_IP3)
+		do_IRQ(3);
+	if (cause & CAUSEF_IP4)
+		do_IRQ(4);
+	if (cause & CAUSEF_IP5)
+		do_IRQ(5);
+	if (cause & CAUSEF_IP6)
+		do_IRQ(6);
+}
+
+#define DEFINE_HWx_IRQDISPATCH(x)					\
+	static void bcm47xx_hw ## x ## _irqdispatch(void)		\
+	{								\
+		do_IRQ(x);						\
+	}
+DEFINE_HWx_IRQDISPATCH(2)
+DEFINE_HWx_IRQDISPATCH(3)
+DEFINE_HWx_IRQDISPATCH(4)
+DEFINE_HWx_IRQDISPATCH(5)
+DEFINE_HWx_IRQDISPATCH(6)
+DEFINE_HWx_IRQDISPATCH(7)
+
+void __init arch_init_irq(void)
+{
+	/*
+	 * This is the first arch callback after mm_init (we can use kmalloc),
+	 * so let's finish bus initialization now.
+	 */
+	bcm47xx_bus_setup();
+
+#ifdef CONFIG_BCM47XX_BCMA
+	if (bcm47xx_bus_type == BCM47XX_BUS_TYPE_BCMA) {
+		bcma_write32(bcm47xx_bus.bcma.bus.drv_mips.core,
+			     BCMA_MIPS_MIPS74K_INTMASK(5), 1 << 31);
+		/*
+		 * the kernel reads the timer irq from some register and thinks
+		 * it's #5, but we offset it by 2 and route to #7
+		 */
+		cp0_compare_irq = 7;
+	}
+#endif
+	mips_cpu_irq_init();
+
+	if (cpu_has_vint) {
+		pr_info("Setting up vectored interrupts\n");
+		set_vi_handler(2, bcm47xx_hw2_irqdispatch);
+		set_vi_handler(3, bcm47xx_hw3_irqdispatch);
+		set_vi_handler(4, bcm47xx_hw4_irqdispatch);
+		set_vi_handler(5, bcm47xx_hw5_irqdispatch);
+		set_vi_handler(6, bcm47xx_hw6_irqdispatch);
+		set_vi_handler(7, bcm47xx_hw7_irqdispatch);
+	}
+}
diff --git a/arch/mips/bcm47xx/leds.c b/arch/mips/bcm47xx/leds.c
new file mode 100644
index 000000000..8e257d089
--- /dev/null
+++ b/arch/mips/bcm47xx/leds.c
@@ -0,0 +1,825 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "bcm47xx_private.h"
+
+#include <linux/leds.h>
+#include <bcm47xx_board.h>
+
+/**************************************************
+ * Database
+ **************************************************/
+
+#define BCM47XX_GPIO_LED(_gpio, _color, _function, _active_low,		\
+			 _default_state)				\
+	{								\
+		.name		= "bcm47xx:" _color ":" _function,	\
+		.gpio		= _gpio,				\
+		.active_low	= _active_low,				\
+		.default_state	= _default_state,			\
+	}
+
+#define BCM47XX_GPIO_LED_TRIGGER(_gpio, _color, _function, _active_low,	\
+				 _default_trigger)			\
+	{								\
+		.name		= "bcm47xx:" _color ":" _function,	\
+		.gpio		= _gpio,				\
+		.active_low	= _active_low,				\
+		.default_state	= LEDS_GPIO_DEFSTATE_OFF,		\
+		.default_trigger	= _default_trigger,		\
+	}
+
+/* Asus */
+
+static const struct gpio_led
+bcm47xx_leds_asus_rtn10u[] __initconst = {
+	BCM47XX_GPIO_LED(5, "green", "wlan", 0, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(6, "green", "power", 1, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(7, "green", "wps", 0, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(8, "green", "usb", 0, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_asus_rtn12[] __initconst = {
+	BCM47XX_GPIO_LED(2, "unk", "power", 1, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(7, "unk", "wlan", 0, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_asus_rtn15u[] __initconst = {
+	/* TODO: Add "wlan" LED */
+	BCM47XX_GPIO_LED(3, "blue", "wan", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(4, "blue", "lan", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(6, "blue", "power", 1, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(9, "blue", "usb", 0, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_asus_rtn16[] __initconst = {
+	BCM47XX_GPIO_LED(1, "blue", "power", 1, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(7, "blue", "wlan", 0, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_asus_rtn66u[] __initconst = {
+	BCM47XX_GPIO_LED(12, "blue", "power", 1, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(15, "blue", "usb", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_asus_wl300g[] __initconst = {
+	BCM47XX_GPIO_LED(0, "unk", "power", 1, LEDS_GPIO_DEFSTATE_ON),
+};
+
+static const struct gpio_led
+bcm47xx_leds_asus_wl320ge[] __initconst = {
+	BCM47XX_GPIO_LED(0, "unk", "wlan", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(2, "unk", "power", 1, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(11, "unk", "link", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_asus_wl330ge[] __initconst = {
+	BCM47XX_GPIO_LED(0, "unk", "power", 1, LEDS_GPIO_DEFSTATE_ON),
+};
+
+static const struct gpio_led
+bcm47xx_leds_asus_wl500g[] __initconst = {
+	BCM47XX_GPIO_LED(0, "unk", "power", 1, LEDS_GPIO_DEFSTATE_ON),
+};
+
+static const struct gpio_led
+bcm47xx_leds_asus_wl500gd[] __initconst = {
+	BCM47XX_GPIO_LED(0, "unk", "power", 1, LEDS_GPIO_DEFSTATE_ON),
+};
+
+static const struct gpio_led
+bcm47xx_leds_asus_wl500gpv1[] __initconst = {
+	BCM47XX_GPIO_LED(1, "unk", "power", 1, LEDS_GPIO_DEFSTATE_ON),
+};
+
+static const struct gpio_led
+bcm47xx_leds_asus_wl500gpv2[] __initconst = {
+	BCM47XX_GPIO_LED(0, "unk", "power", 1, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(1, "unk", "wlan", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_asus_wl500w[] __initconst = {
+	BCM47XX_GPIO_LED(5, "unk", "power", 1, LEDS_GPIO_DEFSTATE_ON),
+};
+
+static const struct gpio_led
+bcm47xx_leds_asus_wl520gc[] __initconst = {
+	BCM47XX_GPIO_LED(0, "unk", "power", 1, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(1, "unk", "wlan", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_asus_wl520gu[] __initconst = {
+	BCM47XX_GPIO_LED(0, "unk", "power", 1, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(1, "unk", "wlan", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_asus_wl700ge[] __initconst = {
+	BCM47XX_GPIO_LED(1, "unk", "power", 1, LEDS_GPIO_DEFSTATE_ON), /* Labeled "READY" (there is no "power" LED). Originally ON, flashing on USB activity. */
+};
+
+static const struct gpio_led
+bcm47xx_leds_asus_wlhdd[] __initconst = {
+	BCM47XX_GPIO_LED(0, "unk", "power", 1, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(2, "unk", "usb", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+/* Belkin */
+
+static const struct gpio_led
+bcm47xx_leds_belkin_f7d4301[] __initconst = {
+	BCM47XX_GPIO_LED(10, "green", "power", 1, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(11, "amber", "power", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(12, "unk", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(13, "unk", "wlan", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(14, "unk", "usb0", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(15, "unk", "usb1", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+/* Buffalo */
+
+static const struct gpio_led
+bcm47xx_leds_buffalo_whr2_a54g54[] __initconst = {
+	BCM47XX_GPIO_LED(7, "unk", "diag", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_buffalo_whr_g125[] __initconst = {
+	BCM47XX_GPIO_LED(1, "unk", "bridge", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(2, "unk", "wlan", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(3, "unk", "internal", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(6, "unk", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(7, "unk", "diag", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_buffalo_whr_g54s[] __initconst = {
+	BCM47XX_GPIO_LED(1, "green", "bridge", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(2, "green", "wlan", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(3, "green", "internal", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(6, "amber", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(7, "red", "diag", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_buffalo_whr_hp_g54[] __initconst = {
+	BCM47XX_GPIO_LED(1, "unk", "bridge", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(2, "unk", "wlan", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(3, "unk", "internal", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(6, "unk", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(7, "unk", "diag", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_buffalo_wzr_g300n[] __initconst = {
+	BCM47XX_GPIO_LED(1, "unk", "bridge", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(6, "unk", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(7, "unk", "diag", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_buffalo_wzr_rs_g54[] __initconst = {
+	BCM47XX_GPIO_LED(6, "unk", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(1, "unk", "vpn", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(7, "unk", "diag", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_buffalo_wzr_rs_g54hp[] __initconst = {
+	BCM47XX_GPIO_LED(6, "unk", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(1, "unk", "vpn", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(7, "unk", "diag", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+/* Dell */
+
+static const struct gpio_led
+bcm47xx_leds_dell_tm2300[] __initconst = {
+	BCM47XX_GPIO_LED(6, "unk", "wlan", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(7, "unk", "power", 1, LEDS_GPIO_DEFSTATE_ON),
+};
+
+/* D-Link */
+
+static const struct gpio_led
+bcm47xx_leds_dlink_dir130[] __initconst = {
+	BCM47XX_GPIO_LED_TRIGGER(0, "green", "status", 1, "timer"), /* Originally blinking when device is ready, separated from "power" LED */
+	BCM47XX_GPIO_LED(6, "blue", "unk", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_dlink_dir330[] __initconst = {
+	BCM47XX_GPIO_LED_TRIGGER(0, "green", "status", 1, "timer"), /* Originally blinking when device is ready, separated from "power" LED */
+	BCM47XX_GPIO_LED(4, "unk", "usb", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(6, "blue", "unk", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+/* Huawei */
+
+static const struct gpio_led
+bcm47xx_leds_huawei_e970[] __initconst = {
+	BCM47XX_GPIO_LED(0, "unk", "wlan", 0, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+/* Linksys */
+
+static const struct gpio_led
+bcm47xx_leds_linksys_e1000v1[] __initconst = {
+	BCM47XX_GPIO_LED(0, "blue", "wlan", 0, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(1, "blue", "power", 0, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(2, "amber", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(4, "blue", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_linksys_e1000v21[] __initconst = {
+	BCM47XX_GPIO_LED(5, "blue", "wlan", 0, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(6, "blue", "power", 1, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(7, "amber", "wps", 0, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(8, "blue", "wps", 0, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_linksys_e2000v1[] __initconst = {
+	BCM47XX_GPIO_LED(1, "blue", "wlan", 0, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(2, "blue", "power", 0, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(3, "blue", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(4, "amber", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_linksys_e3000v1[] __initconst = {
+	BCM47XX_GPIO_LED(0, "amber", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(1, "unk", "wlan", 0, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(3, "blue", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(5, "unk", "power", 0, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(7, "unk", "usb", 0, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_linksys_e3200v1[] __initconst = {
+	BCM47XX_GPIO_LED(3, "green", "power", 1, LEDS_GPIO_DEFSTATE_ON),
+};
+
+static const struct gpio_led
+bcm47xx_leds_linksys_e4200v1[] __initconst = {
+	BCM47XX_GPIO_LED(5, "white", "power", 1, LEDS_GPIO_DEFSTATE_ON),
+};
+
+static const struct gpio_led
+bcm47xx_leds_linksys_wrt150nv1[] __initconst = {
+	BCM47XX_GPIO_LED(1, "unk", "power", 0, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(3, "amber", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(5, "green", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_linksys_wrt150nv11[] __initconst = {
+	BCM47XX_GPIO_LED(1, "unk", "power", 0, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(3, "amber", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(5, "green", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_linksys_wrt160nv1[] __initconst = {
+	BCM47XX_GPIO_LED(1, "unk", "power", 0, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(3, "amber", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(5, "blue", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_linksys_wrt160nv3[] __initconst = {
+	BCM47XX_GPIO_LED(1, "unk", "power", 0, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(2, "amber", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(4, "blue", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_linksys_wrt300n_v1[] __initconst = {
+	BCM47XX_GPIO_LED(1, "green", "power", 0, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(3, "amber", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(5, "green", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_linksys_wrt300nv11[] __initconst = {
+	BCM47XX_GPIO_LED(1, "unk", "power", 0, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(3, "amber", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(5, "green", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_linksys_wrt310nv1[] __initconst = {
+	BCM47XX_GPIO_LED(1, "blue", "power", 0, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(3, "amber", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(9, "blue", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_linksys_wrt320n_v1[] __initconst = {
+	BCM47XX_GPIO_LED(1, "blue", "wlan", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(2, "blue", "power", 0, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(4, "amber", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_linksys_wrt54g_generic[] __initconst = {
+	BCM47XX_GPIO_LED(0, "unk", "dmz", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(1, "unk", "power", 0, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(5, "white", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(7, "orange", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_linksys_wrt54g3gv2[] __initconst = {
+	BCM47XX_GPIO_LED(1, "unk", "power", 0, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(2, "green", "3g", 0, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(3, "blue", "3g", 0, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+/* Verified on: WRT54GS V1.0 */
+static const struct gpio_led
+bcm47xx_leds_linksys_wrt54g_type_0101[] __initconst = {
+	BCM47XX_GPIO_LED(0, "green", "wlan", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(1, "green", "power", 0, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(7, "green", "dmz", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+/* Verified on: WRT54GL V1.1 */
+static const struct gpio_led
+bcm47xx_leds_linksys_wrt54g_type_0467[] __initconst = {
+	BCM47XX_GPIO_LED(0, "green", "wlan", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(1, "green", "power", 0, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(2, "white", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(3, "orange", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(7, "green", "dmz", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_linksys_wrt610nv1[] __initconst = {
+	BCM47XX_GPIO_LED(0, "unk", "usb",  1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(1, "unk", "power",  0, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(3, "amber", "wps",  1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(9, "blue", "wps",  1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_linksys_wrt610nv2[] __initconst = {
+	BCM47XX_GPIO_LED(0, "amber", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(1, "unk", "wlan", 0, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(3, "blue", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(5, "unk", "power", 0, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(7, "unk", "usb", 0, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_linksys_wrtsl54gs[] __initconst = {
+	BCM47XX_GPIO_LED(0, "green", "dmz", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(1, "green", "power", 0, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(5, "white", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(7, "orange", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+/* Luxul */
+
+static const struct gpio_led
+bcm47xx_leds_luxul_abr_4400_v1[] __initconst = {
+	BCM47XX_GPIO_LED(12, "green", "usb", 0, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED_TRIGGER(15, "green", "status", 0, "timer"),
+};
+
+static const struct gpio_led
+bcm47xx_leds_luxul_xap_310_v1[] __initconst = {
+	BCM47XX_GPIO_LED_TRIGGER(6, "green", "status", 1, "timer"),
+};
+
+static const struct gpio_led
+bcm47xx_leds_luxul_xap_1210_v1[] __initconst = {
+	BCM47XX_GPIO_LED_TRIGGER(6, "green", "status", 1, "timer"),
+};
+
+static const struct gpio_led
+bcm47xx_leds_luxul_xap_1230_v1[] __initconst = {
+	BCM47XX_GPIO_LED(3, "blue", "2ghz", 0, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(4, "green", "bridge", 0, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED_TRIGGER(6, "green", "status", 1, "timer"),
+};
+
+static const struct gpio_led
+bcm47xx_leds_luxul_xap_1240_v1[] __initconst = {
+	BCM47XX_GPIO_LED(3, "blue", "2ghz", 0, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(4, "green", "bridge", 0, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED_TRIGGER(6, "green", "status", 1, "timer"),
+};
+
+static const struct gpio_led
+bcm47xx_leds_luxul_xap_1500_v1[] __initconst = {
+	BCM47XX_GPIO_LED_TRIGGER(13, "green", "status", 1, "timer"),
+};
+
+static const struct gpio_led
+bcm47xx_leds_luxul_xap1500_v1_extra[] __initconst = {
+	BCM47XX_GPIO_LED(44, "green", "5ghz", 0, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(76, "green", "2ghz", 0, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_luxul_xbr_4400_v1[] __initconst = {
+	BCM47XX_GPIO_LED(12, "green", "usb", 0, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED_TRIGGER(15, "green", "status", 0, "timer"),
+};
+
+static const struct gpio_led
+bcm47xx_leds_luxul_xvw_p30_v1[] __initconst = {
+	BCM47XX_GPIO_LED_TRIGGER(0, "blue", "status", 1, "timer"),
+	BCM47XX_GPIO_LED(1, "green", "link", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_luxul_xwr_600_v1[] __initconst = {
+	BCM47XX_GPIO_LED(3, "green", "wps", 0, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED_TRIGGER(6, "green", "status", 1, "timer"),
+	BCM47XX_GPIO_LED(9, "green", "usb", 0, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_luxul_xwr_1750_v1[] __initconst = {
+	BCM47XX_GPIO_LED(5, "green", "5ghz", 0, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(12, "green", "usb", 0, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED_TRIGGER(13, "green", "status", 0, "timer"),
+	BCM47XX_GPIO_LED(15, "green", "wps", 0, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_luxul_xwr1750_v1_extra[] __initconst = {
+	BCM47XX_GPIO_LED(76, "green", "2ghz", 0, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+/* Microsoft */
+
+static const struct gpio_led
+bcm47xx_leds_microsoft_nm700[] __initconst = {
+	BCM47XX_GPIO_LED(6, "unk", "power", 0, LEDS_GPIO_DEFSTATE_ON),
+};
+
+/* Motorola */
+
+static const struct gpio_led
+bcm47xx_leds_motorola_we800g[] __initconst = {
+	BCM47XX_GPIO_LED(1, "amber", "wlan", 0, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(2, "unk", "unk", 1, LEDS_GPIO_DEFSTATE_OFF), /* There are only 3 LEDs: Power, Wireless and Device (ethernet) */
+	BCM47XX_GPIO_LED(4, "green", "power", 0, LEDS_GPIO_DEFSTATE_ON),
+};
+
+static const struct gpio_led
+bcm47xx_leds_motorola_wr850gp[] __initconst = {
+	BCM47XX_GPIO_LED(0, "unk", "wlan", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(1, "unk", "power", 0, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(6, "unk", "dmz", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(7, "unk", "diag", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_motorola_wr850gv2v3[] __initconst = {
+	BCM47XX_GPIO_LED(0, "unk", "wlan", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(1, "unk", "power", 0, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(7, "unk", "diag", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+/* Netgear */
+
+static const struct gpio_led
+bcm47xx_leds_netgear_wndr3400v1[] __initconst = {
+	BCM47XX_GPIO_LED(2, "green", "usb", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(3, "green", "power", 0, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(7, "amber", "power", 0, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_netgear_wndr4500v1[] __initconst = {
+	BCM47XX_GPIO_LED(1, "green", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(2, "green", "power", 1, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(3, "amber", "power", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(8, "green", "usb1", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(9, "green", "2ghz", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(11, "blue", "5ghz", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(14, "green", "usb2", 1, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_netgear_wnr1000_v3[] __initconst = {
+	BCM47XX_GPIO_LED(0, "blue", "wlan", 0, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(1, "green", "wps", 0, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_netgear_wnr3500lv1[] __initconst = {
+	BCM47XX_GPIO_LED(0, "blue", "wlan", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(1, "green", "wps", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(2, "green", "wan", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(3, "green", "power", 0, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(7, "amber", "power", 0, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_netgear_wnr3500lv2[] __initconst = {
+	BCM47XX_GPIO_LED(0, "blue", "wlan", 0, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(1, "green", "wps", 0, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(3, "green", "power", 0, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(7, "amber", "power", 0, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+static const struct gpio_led
+bcm47xx_leds_netgear_wnr834bv2[] __initconst = {
+	BCM47XX_GPIO_LED(2, "green", "power", 0, LEDS_GPIO_DEFSTATE_ON),
+	BCM47XX_GPIO_LED(3, "amber", "power", 0, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(7, "unk", "connected", 0, LEDS_GPIO_DEFSTATE_OFF),
+};
+
+/* Siemens */
+static const struct gpio_led
+bcm47xx_leds_siemens_se505v2[] __initconst = {
+	BCM47XX_GPIO_LED(0, "unk", "dmz", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(3, "unk", "wlan", 1, LEDS_GPIO_DEFSTATE_OFF),
+	BCM47XX_GPIO_LED(5, "unk", "power", 1, LEDS_GPIO_DEFSTATE_ON),
+};
+
+/* SimpleTech */
+
+static const struct gpio_led
+bcm47xx_leds_simpletech_simpleshare[] __initconst = {
+	BCM47XX_GPIO_LED(1, "unk", "status", 1, LEDS_GPIO_DEFSTATE_OFF), /* "Ready" LED */
+};
+
+/**************************************************
+ * Init
+ **************************************************/
+
+static struct gpio_led_platform_data bcm47xx_leds_pdata __initdata;
+
+#define bcm47xx_set_pdata(dev_leds) do {				\
+	bcm47xx_leds_pdata.leds = dev_leds;				\
+	bcm47xx_leds_pdata.num_leds = ARRAY_SIZE(dev_leds);		\
+} while (0)
+
+static struct gpio_led_platform_data bcm47xx_leds_pdata_extra __initdata = {};
+#define bcm47xx_set_pdata_extra(dev_leds) do {				\
+	bcm47xx_leds_pdata_extra.leds = dev_leds;			\
+	bcm47xx_leds_pdata_extra.num_leds = ARRAY_SIZE(dev_leds);	\
+} while (0)
+
+void __init bcm47xx_leds_register(void)
+{
+	enum bcm47xx_board board = bcm47xx_board_get();
+
+	switch (board) {
+	case BCM47XX_BOARD_ASUS_RTN10U:
+		bcm47xx_set_pdata(bcm47xx_leds_asus_rtn10u);
+		break;
+	case BCM47XX_BOARD_ASUS_RTN12:
+		bcm47xx_set_pdata(bcm47xx_leds_asus_rtn12);
+		break;
+	case BCM47XX_BOARD_ASUS_RTN15U:
+		bcm47xx_set_pdata(bcm47xx_leds_asus_rtn15u);
+		break;
+	case BCM47XX_BOARD_ASUS_RTN16:
+		bcm47xx_set_pdata(bcm47xx_leds_asus_rtn16);
+		break;
+	case BCM47XX_BOARD_ASUS_RTN66U:
+		bcm47xx_set_pdata(bcm47xx_leds_asus_rtn66u);
+		break;
+	case BCM47XX_BOARD_ASUS_WL300G:
+		bcm47xx_set_pdata(bcm47xx_leds_asus_wl300g);
+		break;
+	case BCM47XX_BOARD_ASUS_WL320GE:
+		bcm47xx_set_pdata(bcm47xx_leds_asus_wl320ge);
+		break;
+	case BCM47XX_BOARD_ASUS_WL330GE:
+		bcm47xx_set_pdata(bcm47xx_leds_asus_wl330ge);
+		break;
+	case BCM47XX_BOARD_ASUS_WL500G:
+		bcm47xx_set_pdata(bcm47xx_leds_asus_wl500g);
+		break;
+	case BCM47XX_BOARD_ASUS_WL500GD:
+		bcm47xx_set_pdata(bcm47xx_leds_asus_wl500gd);
+		break;
+	case BCM47XX_BOARD_ASUS_WL500GPV1:
+		bcm47xx_set_pdata(bcm47xx_leds_asus_wl500gpv1);
+		break;
+	case BCM47XX_BOARD_ASUS_WL500GPV2:
+		bcm47xx_set_pdata(bcm47xx_leds_asus_wl500gpv2);
+		break;
+	case BCM47XX_BOARD_ASUS_WL500W:
+		bcm47xx_set_pdata(bcm47xx_leds_asus_wl500w);
+		break;
+	case BCM47XX_BOARD_ASUS_WL520GC:
+		bcm47xx_set_pdata(bcm47xx_leds_asus_wl520gc);
+		break;
+	case BCM47XX_BOARD_ASUS_WL520GU:
+		bcm47xx_set_pdata(bcm47xx_leds_asus_wl520gu);
+		break;
+	case BCM47XX_BOARD_ASUS_WL700GE:
+		bcm47xx_set_pdata(bcm47xx_leds_asus_wl700ge);
+		break;
+	case BCM47XX_BOARD_ASUS_WLHDD:
+		bcm47xx_set_pdata(bcm47xx_leds_asus_wlhdd);
+		break;
+
+	case BCM47XX_BOARD_BELKIN_F7D3301:
+	case BCM47XX_BOARD_BELKIN_F7D3302:
+	case BCM47XX_BOARD_BELKIN_F7D4301:
+	case BCM47XX_BOARD_BELKIN_F7D4302:
+	case BCM47XX_BOARD_BELKIN_F7D4401:
+		bcm47xx_set_pdata(bcm47xx_leds_belkin_f7d4301);
+		break;
+
+	case BCM47XX_BOARD_BUFFALO_WHR2_A54G54:
+		bcm47xx_set_pdata(bcm47xx_leds_buffalo_whr2_a54g54);
+		break;
+	case BCM47XX_BOARD_BUFFALO_WHR_G125:
+		bcm47xx_set_pdata(bcm47xx_leds_buffalo_whr_g125);
+		break;
+	case BCM47XX_BOARD_BUFFALO_WHR_G54S:
+		bcm47xx_set_pdata(bcm47xx_leds_buffalo_whr_g54s);
+		break;
+	case BCM47XX_BOARD_BUFFALO_WHR_HP_G54:
+		bcm47xx_set_pdata(bcm47xx_leds_buffalo_whr_hp_g54);
+		break;
+	case BCM47XX_BOARD_BUFFALO_WZR_G300N:
+		bcm47xx_set_pdata(bcm47xx_leds_buffalo_wzr_g300n);
+		break;
+	case BCM47XX_BOARD_BUFFALO_WZR_RS_G54:
+		bcm47xx_set_pdata(bcm47xx_leds_buffalo_wzr_rs_g54);
+		break;
+	case BCM47XX_BOARD_BUFFALO_WZR_RS_G54HP:
+		bcm47xx_set_pdata(bcm47xx_leds_buffalo_wzr_rs_g54hp);
+		break;
+
+	case BCM47XX_BOARD_DELL_TM2300:
+		bcm47xx_set_pdata(bcm47xx_leds_dell_tm2300);
+		break;
+
+	case BCM47XX_BOARD_DLINK_DIR130:
+		bcm47xx_set_pdata(bcm47xx_leds_dlink_dir130);
+		break;
+	case BCM47XX_BOARD_DLINK_DIR330:
+		bcm47xx_set_pdata(bcm47xx_leds_dlink_dir330);
+		break;
+
+	case BCM47XX_BOARD_HUAWEI_E970:
+		bcm47xx_set_pdata(bcm47xx_leds_huawei_e970);
+		break;
+
+	case BCM47XX_BOARD_LINKSYS_E1000V1:
+		bcm47xx_set_pdata(bcm47xx_leds_linksys_e1000v1);
+		break;
+	case BCM47XX_BOARD_LINKSYS_E1000V21:
+		bcm47xx_set_pdata(bcm47xx_leds_linksys_e1000v21);
+		break;
+	case BCM47XX_BOARD_LINKSYS_E2000V1:
+		bcm47xx_set_pdata(bcm47xx_leds_linksys_e2000v1);
+		break;
+	case BCM47XX_BOARD_LINKSYS_E3000V1:
+		bcm47xx_set_pdata(bcm47xx_leds_linksys_e3000v1);
+		break;
+	case BCM47XX_BOARD_LINKSYS_E3200V1:
+		bcm47xx_set_pdata(bcm47xx_leds_linksys_e3200v1);
+		break;
+	case BCM47XX_BOARD_LINKSYS_E4200V1:
+		bcm47xx_set_pdata(bcm47xx_leds_linksys_e4200v1);
+		break;
+	case BCM47XX_BOARD_LINKSYS_WRT150NV1:
+		bcm47xx_set_pdata(bcm47xx_leds_linksys_wrt150nv1);
+		break;
+	case BCM47XX_BOARD_LINKSYS_WRT150NV11:
+		bcm47xx_set_pdata(bcm47xx_leds_linksys_wrt150nv11);
+		break;
+	case BCM47XX_BOARD_LINKSYS_WRT160NV1:
+		bcm47xx_set_pdata(bcm47xx_leds_linksys_wrt160nv1);
+		break;
+	case BCM47XX_BOARD_LINKSYS_WRT160NV3:
+		bcm47xx_set_pdata(bcm47xx_leds_linksys_wrt160nv3);
+		break;
+	case BCM47XX_BOARD_LINKSYS_WRT300N_V1:
+		bcm47xx_set_pdata(bcm47xx_leds_linksys_wrt300n_v1);
+		break;
+	case BCM47XX_BOARD_LINKSYS_WRT300NV11:
+		bcm47xx_set_pdata(bcm47xx_leds_linksys_wrt300nv11);
+		break;
+	case BCM47XX_BOARD_LINKSYS_WRT310NV1:
+		bcm47xx_set_pdata(bcm47xx_leds_linksys_wrt310nv1);
+		break;
+	case BCM47XX_BOARD_LINKSYS_WRT320N_V1:
+		bcm47xx_set_pdata(bcm47xx_leds_linksys_wrt320n_v1);
+		break;
+	case BCM47XX_BOARD_LINKSYS_WRT54G3GV2:
+		bcm47xx_set_pdata(bcm47xx_leds_linksys_wrt54g3gv2);
+		break;
+	case BCM47XX_BOARD_LINKSYS_WRT54G_TYPE_0101:
+		bcm47xx_set_pdata(bcm47xx_leds_linksys_wrt54g_type_0101);
+		break;
+	case BCM47XX_BOARD_LINKSYS_WRT54G_TYPE_0467:
+		bcm47xx_set_pdata(bcm47xx_leds_linksys_wrt54g_type_0467);
+		break;
+	case BCM47XX_BOARD_LINKSYS_WRT54G_TYPE_0708:
+		bcm47xx_set_pdata(bcm47xx_leds_linksys_wrt54g_generic);
+		break;
+	case BCM47XX_BOARD_LINKSYS_WRT610NV1:
+		bcm47xx_set_pdata(bcm47xx_leds_linksys_wrt610nv1);
+		break;
+	case BCM47XX_BOARD_LINKSYS_WRT610NV2:
+		bcm47xx_set_pdata(bcm47xx_leds_linksys_wrt610nv2);
+		break;
+	case BCM47XX_BOARD_LINKSYS_WRTSL54GS:
+		bcm47xx_set_pdata(bcm47xx_leds_linksys_wrtsl54gs);
+		break;
+
+	case BCM47XX_BOARD_LUXUL_ABR_4400_V1:
+		bcm47xx_set_pdata(bcm47xx_leds_luxul_abr_4400_v1);
+		break;
+	case BCM47XX_BOARD_LUXUL_XAP_310_V1:
+		bcm47xx_set_pdata(bcm47xx_leds_luxul_xap_310_v1);
+		break;
+	case BCM47XX_BOARD_LUXUL_XAP_1210_V1:
+		bcm47xx_set_pdata(bcm47xx_leds_luxul_xap_1210_v1);
+		break;
+	case BCM47XX_BOARD_LUXUL_XAP_1230_V1:
+		bcm47xx_set_pdata(bcm47xx_leds_luxul_xap_1230_v1);
+		break;
+	case BCM47XX_BOARD_LUXUL_XAP_1240_V1:
+		bcm47xx_set_pdata(bcm47xx_leds_luxul_xap_1240_v1);
+		break;
+	case BCM47XX_BOARD_LUXUL_XAP_1500_V1:
+		bcm47xx_set_pdata(bcm47xx_leds_luxul_xap_1500_v1);
+		bcm47xx_set_pdata_extra(bcm47xx_leds_luxul_xap1500_v1_extra);
+		break;
+	case BCM47XX_BOARD_LUXUL_XBR_4400_V1:
+		bcm47xx_set_pdata(bcm47xx_leds_luxul_xbr_4400_v1);
+		break;
+	case BCM47XX_BOARD_LUXUL_XVW_P30_V1:
+		bcm47xx_set_pdata(bcm47xx_leds_luxul_xvw_p30_v1);
+		break;
+	case BCM47XX_BOARD_LUXUL_XWR_600_V1:
+		bcm47xx_set_pdata(bcm47xx_leds_luxul_xwr_600_v1);
+		break;
+	case BCM47XX_BOARD_LUXUL_XWR_1750_V1:
+		bcm47xx_set_pdata(bcm47xx_leds_luxul_xwr_1750_v1);
+		bcm47xx_set_pdata_extra(bcm47xx_leds_luxul_xwr1750_v1_extra);
+		break;
+
+	case BCM47XX_BOARD_MICROSOFT_MN700:
+		bcm47xx_set_pdata(bcm47xx_leds_microsoft_nm700);
+		break;
+
+	case BCM47XX_BOARD_MOTOROLA_WE800G:
+		bcm47xx_set_pdata(bcm47xx_leds_motorola_we800g);
+		break;
+	case BCM47XX_BOARD_MOTOROLA_WR850GP:
+		bcm47xx_set_pdata(bcm47xx_leds_motorola_wr850gp);
+		break;
+	case BCM47XX_BOARD_MOTOROLA_WR850GV2V3:
+		bcm47xx_set_pdata(bcm47xx_leds_motorola_wr850gv2v3);
+		break;
+
+	case BCM47XX_BOARD_NETGEAR_WNDR3400V1:
+		bcm47xx_set_pdata(bcm47xx_leds_netgear_wndr3400v1);
+		break;
+	case BCM47XX_BOARD_NETGEAR_WNDR4500V1:
+		bcm47xx_set_pdata(bcm47xx_leds_netgear_wndr4500v1);
+		break;
+	case BCM47XX_BOARD_NETGEAR_WNR1000_V3:
+		bcm47xx_set_pdata(bcm47xx_leds_netgear_wnr1000_v3);
+		break;
+	case BCM47XX_BOARD_NETGEAR_WNR3500L:
+		bcm47xx_set_pdata(bcm47xx_leds_netgear_wnr3500lv1);
+		break;
+	case BCM47XX_BOARD_NETGEAR_WNR3500L_V2:
+		bcm47xx_set_pdata(bcm47xx_leds_netgear_wnr3500lv2);
+		break;
+	case BCM47XX_BOARD_NETGEAR_WNR834BV2:
+		bcm47xx_set_pdata(bcm47xx_leds_netgear_wnr834bv2);
+		break;
+
+	case BCM47XX_BOARD_SIEMENS_SE505V2:
+		bcm47xx_set_pdata(bcm47xx_leds_siemens_se505v2);
+		break;
+
+	case BCM47XX_BOARD_SIMPLETECH_SIMPLESHARE:
+		bcm47xx_set_pdata(bcm47xx_leds_simpletech_simpleshare);
+		break;
+
+	default:
+		pr_debug("No LEDs configuration found for this device\n");
+		return;
+	}
+
+	gpio_led_register_device(-1, &bcm47xx_leds_pdata);
+	if (bcm47xx_leds_pdata_extra.num_leds)
+		gpio_led_register_device(0, &bcm47xx_leds_pdata_extra);
+}
diff --git a/arch/mips/bcm47xx/prom.c b/arch/mips/bcm47xx/prom.c
new file mode 100644
index 000000000..a9bea411d
--- /dev/null
+++ b/arch/mips/bcm47xx/prom.c
@@ -0,0 +1,178 @@
+/*
+ *  Copyright (C) 2004 Florian Schirmer <jolt@tuxbox.org>
+ *  Copyright (C) 2007 Aurelien Jarno <aurelien@aurel32.net>
+ *  Copyright (C) 2010-2012 Hauke Mehrtens <hauke@hauke-m.de>
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/memblock.h>
+#include <linux/spinlock.h>
+#include <linux/ssb/ssb_driver_chipcommon.h>
+#include <linux/ssb/ssb_regs.h>
+#include <linux/smp.h>
+#include <asm/bootinfo.h>
+#include <bcm47xx.h>
+#include <bcm47xx_board.h>
+
+static char bcm47xx_system_type[20] = "Broadcom BCM47XX";
+
+const char *get_system_type(void)
+{
+	return bcm47xx_system_type;
+}
+
+__init void bcm47xx_set_system_type(u16 chip_id)
+{
+	snprintf(bcm47xx_system_type, sizeof(bcm47xx_system_type),
+		 (chip_id > 0x9999) ? "Broadcom BCM%d" :
+				      "Broadcom BCM%04X",
+		 chip_id);
+}
+
+static unsigned long lowmem __initdata;
+
+static __init void prom_init_mem(void)
+{
+	unsigned long mem;
+	unsigned long max;
+	unsigned long off;
+	struct cpuinfo_mips *c = &current_cpu_data;
+
+	/* Figure out memory size by finding aliases.
+	 *
+	 * We should theoretically use the mapping from CFE using cfe_enummem().
+	 * However as the BCM47XX is mostly used on low-memory systems, we
+	 * want to reuse the memory used by CFE (around 4MB). That means cfe_*
+	 * functions stop to work at some point during the boot, we should only
+	 * call them at the beginning of the boot.
+	 *
+	 * BCM47XX uses 128MB for addressing the ram, if the system contains
+	 * less than that amount of ram it remaps the ram more often into the
+	 * available space.
+	 */
+
+	/* Physical address, without mapping to any kernel segment */
+	off = CPHYSADDR((unsigned long)prom_init);
+
+	/* Accessing memory after 128 MiB will cause an exception */
+	max = 128 << 20;
+
+	for (mem = 1 << 20; mem < max; mem += 1 << 20) {
+		/* Loop condition may be not enough, off may be over 1 MiB */
+		if (off + mem >= max) {
+			mem = max;
+			pr_debug("Assume 128MB RAM\n");
+			break;
+		}
+		if (!memcmp((void *)prom_init, (void *)prom_init + mem, 32))
+			break;
+	}
+	lowmem = mem;
+
+	/* Ignoring the last page when ddr size is 128M. Cached
+	 * accesses to last page is causing the processor to prefetch
+	 * using address above 128M stepping out of the ddr address
+	 * space.
+	 */
+	if (c->cputype == CPU_74K && (mem == (128  << 20)))
+		mem -= 0x1000;
+	memblock_add(0, mem);
+}
+
+/*
+ * This is the first serial on the chip common core, it is at this position
+ * for sb (ssb) and ai (bcma) bus.
+ */
+#define BCM47XX_SERIAL_ADDR (SSB_ENUM_BASE + SSB_CHIPCO_UART0_DATA)
+
+void __init prom_init(void)
+{
+	prom_init_mem();
+	setup_8250_early_printk_port(CKSEG1ADDR(BCM47XX_SERIAL_ADDR), 0, 0);
+}
+
+#if defined(CONFIG_BCM47XX_BCMA) && defined(CONFIG_HIGHMEM)
+
+#define EXTVBASE	0xc0000000
+#define ENTRYLO(x)	((pte_val(pfn_pte((x) >> _PFN_SHIFT, PAGE_KERNEL_UNCACHED)) >> 6) | 1)
+
+#include <asm/tlbflush.h>
+
+/* Stripped version of tlb_init, with the call to build_tlb_refill_handler
+ * dropped. Calling it at this stage causes a hang.
+ */
+void early_tlb_init(void)
+{
+	write_c0_pagemask(PM_DEFAULT_MASK);
+	write_c0_wired(0);
+	temp_tlb_entry = current_cpu_data.tlbsize - 1;
+	local_flush_tlb_all();
+}
+
+void __init bcm47xx_prom_highmem_init(void)
+{
+	unsigned long off = (unsigned long)prom_init;
+	unsigned long extmem = 0;
+	bool highmem_region = false;
+
+	if (WARN_ON(bcm47xx_bus_type != BCM47XX_BUS_TYPE_BCMA))
+		return;
+
+	if (bcm47xx_bus.bcma.bus.chipinfo.id == BCMA_CHIP_ID_BCM4706)
+		highmem_region = true;
+
+	if (lowmem != 128 << 20 || !highmem_region)
+		return;
+
+	early_tlb_init();
+
+	/* Add one temporary TLB entry to map SDRAM Region 2.
+	 *      Physical        Virtual
+	 *      0x80000000      0xc0000000      (1st: 256MB)
+	 *      0x90000000      0xd0000000      (2nd: 256MB)
+	 */
+	add_temporary_entry(ENTRYLO(0x80000000),
+			    ENTRYLO(0x80000000 + (256 << 20)),
+			    EXTVBASE, PM_256M);
+
+	off = EXTVBASE + __pa(off);
+	for (extmem = 128 << 20; extmem < 512 << 20; extmem <<= 1) {
+		if (!memcmp((void *)prom_init, (void *)(off + extmem), 16))
+			break;
+	}
+	extmem -= lowmem;
+
+	early_tlb_init();
+
+	if (!extmem)
+		return;
+
+	pr_warn("Found %lu MiB of extra memory, but highmem is unsupported yet!\n",
+		extmem >> 20);
+
+	/* TODO: Register extra memory */
+}
+
+#endif /* defined(CONFIG_BCM47XX_BCMA) && defined(CONFIG_HIGHMEM) */
diff --git a/arch/mips/bcm47xx/serial.c b/arch/mips/bcm47xx/serial.c
new file mode 100644
index 000000000..e3c9872a4
--- /dev/null
+++ b/arch/mips/bcm47xx/serial.c
@@ -0,0 +1,93 @@
+/*
+ * 8250 UART probe driver for the BCM47XX platforms
+ * Author: Aurelien Jarno
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2007 Aurelien Jarno <aurelien@aurel32.net>
+ */
+
+#include <linux/init.h>
+#include <linux/serial.h>
+#include <linux/serial_8250.h>
+#include <linux/ssb/ssb.h>
+#include <bcm47xx.h>
+
+static struct plat_serial8250_port uart8250_data[5];
+
+static struct platform_device uart8250_device = {
+	.name			= "serial8250",
+	.id			= PLAT8250_DEV_PLATFORM,
+	.dev			= {
+		.platform_data	= uart8250_data,
+	},
+};
+
+#ifdef CONFIG_BCM47XX_SSB
+static int __init uart8250_init_ssb(void)
+{
+	int i;
+	struct ssb_mipscore *mcore = &(bcm47xx_bus.ssb.mipscore);
+
+	memset(&uart8250_data, 0,  sizeof(uart8250_data));
+
+	for (i = 0; i < mcore->nr_serial_ports &&
+		    i < ARRAY_SIZE(uart8250_data) - 1; i++) {
+		struct plat_serial8250_port *p = &(uart8250_data[i]);
+		struct ssb_serial_port *ssb_port = &(mcore->serial_ports[i]);
+
+		p->mapbase = (unsigned int)ssb_port->regs;
+		p->membase = (void *)ssb_port->regs;
+		p->irq = ssb_port->irq + 2;
+		p->uartclk = ssb_port->baud_base;
+		p->regshift = ssb_port->reg_shift;
+		p->iotype = UPIO_MEM;
+		p->flags = UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ;
+	}
+	return platform_device_register(&uart8250_device);
+}
+#endif
+
+#ifdef CONFIG_BCM47XX_BCMA
+static int __init uart8250_init_bcma(void)
+{
+	int i;
+	struct bcma_drv_cc *cc = &(bcm47xx_bus.bcma.bus.drv_cc);
+
+	memset(&uart8250_data, 0,  sizeof(uart8250_data));
+
+	for (i = 0; i < cc->nr_serial_ports &&
+		    i < ARRAY_SIZE(uart8250_data) - 1; i++) {
+		struct plat_serial8250_port *p = &(uart8250_data[i]);
+		struct bcma_serial_port *bcma_port;
+		bcma_port = &(cc->serial_ports[i]);
+
+		p->mapbase = (unsigned int)bcma_port->regs;
+		p->membase = (void *)bcma_port->regs;
+		p->irq = bcma_port->irq;
+		p->uartclk = bcma_port->baud_base;
+		p->regshift = bcma_port->reg_shift;
+		p->iotype = UPIO_MEM;
+		p->flags = UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ;
+	}
+	return platform_device_register(&uart8250_device);
+}
+#endif
+
+static int __init uart8250_init(void)
+{
+	switch (bcm47xx_bus_type) {
+#ifdef CONFIG_BCM47XX_SSB
+	case BCM47XX_BUS_TYPE_SSB:
+		return uart8250_init_ssb();
+#endif
+#ifdef CONFIG_BCM47XX_BCMA
+	case BCM47XX_BUS_TYPE_BCMA:
+		return uart8250_init_bcma();
+#endif
+	}
+	return -EINVAL;
+}
+device_initcall(uart8250_init);
diff --git a/arch/mips/bcm47xx/setup.c b/arch/mips/bcm47xx/setup.c
new file mode 100644
index 000000000..94bf83957
--- /dev/null
+++ b/arch/mips/bcm47xx/setup.c
@@ -0,0 +1,280 @@
+/*
+ *  Copyright (C) 2004 Florian Schirmer <jolt@tuxbox.org>
+ *  Copyright (C) 2006 Felix Fietkau <nbd@openwrt.org>
+ *  Copyright (C) 2006 Michael Buesch <m@bues.ch>
+ *  Copyright (C) 2010 Waldemar Brodkorb <wbx@openadk.org>
+ *  Copyright (C) 2010-2012 Hauke Mehrtens <hauke@hauke-m.de>
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include "bcm47xx_private.h"
+
+#include <linux/bcm47xx_sprom.h>
+#include <linux/export.h>
+#include <linux/types.h>
+#include <linux/ethtool.h>
+#include <linux/phy.h>
+#include <linux/phy_fixed.h>
+#include <linux/ssb/ssb.h>
+#include <linux/ssb/ssb_embedded.h>
+#include <linux/bcma/bcma_soc.h>
+#include <asm/bootinfo.h>
+#include <asm/idle.h>
+#include <asm/prom.h>
+#include <asm/reboot.h>
+#include <asm/time.h>
+#include <bcm47xx.h>
+#include <bcm47xx_board.h>
+
+union bcm47xx_bus bcm47xx_bus;
+EXPORT_SYMBOL(bcm47xx_bus);
+
+enum bcm47xx_bus_type bcm47xx_bus_type;
+EXPORT_SYMBOL(bcm47xx_bus_type);
+
+static void bcm47xx_machine_restart(char *command)
+{
+	pr_alert("Please stand by while rebooting the system...\n");
+	local_irq_disable();
+	/* Set the watchdog timer to reset immediately */
+	switch (bcm47xx_bus_type) {
+#ifdef CONFIG_BCM47XX_SSB
+	case BCM47XX_BUS_TYPE_SSB:
+		if (bcm47xx_bus.ssb.chip_id == 0x4785)
+			write_c0_diag4(1 << 22);
+		ssb_watchdog_timer_set(&bcm47xx_bus.ssb, 1);
+		if (bcm47xx_bus.ssb.chip_id == 0x4785) {
+			__asm__ __volatile__(
+				".set\tmips3\n\t"
+				"sync\n\t"
+				"wait\n\t"
+				".set\tmips0");
+		}
+		break;
+#endif
+#ifdef CONFIG_BCM47XX_BCMA
+	case BCM47XX_BUS_TYPE_BCMA:
+		bcma_chipco_watchdog_timer_set(&bcm47xx_bus.bcma.bus.drv_cc, 1);
+		break;
+#endif
+	}
+	while (1)
+		cpu_relax();
+}
+
+static void bcm47xx_machine_halt(void)
+{
+	/* Disable interrupts and watchdog and spin forever */
+	local_irq_disable();
+	switch (bcm47xx_bus_type) {
+#ifdef CONFIG_BCM47XX_SSB
+	case BCM47XX_BUS_TYPE_SSB:
+		ssb_watchdog_timer_set(&bcm47xx_bus.ssb, 0);
+		break;
+#endif
+#ifdef CONFIG_BCM47XX_BCMA
+	case BCM47XX_BUS_TYPE_BCMA:
+		bcma_chipco_watchdog_timer_set(&bcm47xx_bus.bcma.bus.drv_cc, 0);
+		break;
+#endif
+	}
+	while (1)
+		cpu_relax();
+}
+
+#ifdef CONFIG_BCM47XX_SSB
+static void __init bcm47xx_register_ssb(void)
+{
+	int err;
+	char buf[100];
+	struct ssb_mipscore *mcore;
+
+	err = ssb_bus_host_soc_register(&bcm47xx_bus.ssb, SSB_ENUM_BASE);
+	if (err)
+		panic("Failed to initialize SSB bus (err %d)", err);
+
+	mcore = &bcm47xx_bus.ssb.mipscore;
+	if (bcm47xx_nvram_getenv("kernel_args", buf, sizeof(buf)) >= 0) {
+		if (strstr(buf, "console=ttyS1")) {
+			struct ssb_serial_port port;
+
+			pr_debug("Swapping serial ports!\n");
+			/* swap serial ports */
+			memcpy(&port, &mcore->serial_ports[0], sizeof(port));
+			memcpy(&mcore->serial_ports[0], &mcore->serial_ports[1],
+			       sizeof(port));
+			memcpy(&mcore->serial_ports[1], &port, sizeof(port));
+		}
+	}
+}
+#endif
+
+#ifdef CONFIG_BCM47XX_BCMA
+static void __init bcm47xx_register_bcma(void)
+{
+	int err;
+
+	err = bcma_host_soc_register(&bcm47xx_bus.bcma);
+	if (err)
+		panic("Failed to register BCMA bus (err %d)", err);
+}
+#endif
+
+/*
+ * Memory setup is done in the early part of MIPS's arch_mem_init. It's supposed
+ * to detect memory and record it with memblock_add.
+ * Any extra initializaion performed here must not use kmalloc or bootmem.
+ */
+void __init plat_mem_setup(void)
+{
+	struct cpuinfo_mips *c = &current_cpu_data;
+
+	if (c->cputype == CPU_74K) {
+		pr_info("Using bcma bus\n");
+#ifdef CONFIG_BCM47XX_BCMA
+		bcm47xx_bus_type = BCM47XX_BUS_TYPE_BCMA;
+		bcm47xx_register_bcma();
+		bcm47xx_set_system_type(bcm47xx_bus.bcma.bus.chipinfo.id);
+#ifdef CONFIG_HIGHMEM
+		bcm47xx_prom_highmem_init();
+#endif
+#endif
+	} else {
+		pr_info("Using ssb bus\n");
+#ifdef CONFIG_BCM47XX_SSB
+		bcm47xx_bus_type = BCM47XX_BUS_TYPE_SSB;
+		bcm47xx_sprom_register_fallbacks();
+		bcm47xx_register_ssb();
+		bcm47xx_set_system_type(bcm47xx_bus.ssb.chip_id);
+#endif
+	}
+
+	_machine_restart = bcm47xx_machine_restart;
+	_machine_halt = bcm47xx_machine_halt;
+	pm_power_off = bcm47xx_machine_halt;
+}
+
+#ifdef CONFIG_BCM47XX_BCMA
+static struct device * __init bcm47xx_setup_device(void)
+{
+	struct device *dev;
+	int err;
+
+	dev = kzalloc(sizeof(*dev), GFP_KERNEL);
+	if (!dev)
+		return NULL;
+
+	err = dev_set_name(dev, "bcm47xx_soc");
+	if (err) {
+		pr_err("Failed to set SoC device name: %d\n", err);
+		kfree(dev);
+		return NULL;
+	}
+
+	err = dma_coerce_mask_and_coherent(dev, DMA_BIT_MASK(32));
+	if (err)
+		pr_err("Failed to set SoC DMA mask: %d\n", err);
+
+	return dev;
+}
+#endif
+
+/*
+ * This finishes bus initialization doing things that were not possible without
+ * kmalloc. Make sure to call it late enough (after mm_init).
+ */
+void __init bcm47xx_bus_setup(void)
+{
+#ifdef CONFIG_BCM47XX_BCMA
+	if (bcm47xx_bus_type == BCM47XX_BUS_TYPE_BCMA) {
+		int err;
+
+		bcm47xx_bus.bcma.dev = bcm47xx_setup_device();
+		if (!bcm47xx_bus.bcma.dev)
+			panic("Failed to setup SoC device\n");
+
+		err = bcma_host_soc_init(&bcm47xx_bus.bcma);
+		if (err)
+			panic("Failed to initialize BCMA bus (err %d)", err);
+	}
+#endif
+
+	/* With bus initialized we can access NVRAM and detect the board */
+	bcm47xx_board_detect();
+	mips_set_machine_name(bcm47xx_board_get_name());
+}
+
+static int __init bcm47xx_cpu_fixes(void)
+{
+	switch (bcm47xx_bus_type) {
+#ifdef CONFIG_BCM47XX_SSB
+	case BCM47XX_BUS_TYPE_SSB:
+		/* Nothing to do */
+		break;
+#endif
+#ifdef CONFIG_BCM47XX_BCMA
+	case BCM47XX_BUS_TYPE_BCMA:
+		/* The BCM4706 has a problem with the CPU wait instruction.
+		 * When r4k_wait or r4k_wait_irqoff is used will just hang and
+		 * not return from a msleep(). Removing the cpu_wait
+		 * functionality is a workaround for this problem. The BCM4716
+		 * does not have this problem.
+		 */
+		if (bcm47xx_bus.bcma.bus.chipinfo.id == BCMA_CHIP_ID_BCM4706)
+			cpu_wait = NULL;
+		break;
+#endif
+	}
+	return 0;
+}
+arch_initcall(bcm47xx_cpu_fixes);
+
+static struct fixed_phy_status bcm47xx_fixed_phy_status __initdata = {
+	.link	= 1,
+	.speed	= SPEED_100,
+	.duplex	= DUPLEX_FULL,
+};
+
+static int __init bcm47xx_register_bus_complete(void)
+{
+	switch (bcm47xx_bus_type) {
+#ifdef CONFIG_BCM47XX_SSB
+	case BCM47XX_BUS_TYPE_SSB:
+		/* Nothing to do */
+		break;
+#endif
+#ifdef CONFIG_BCM47XX_BCMA
+	case BCM47XX_BUS_TYPE_BCMA:
+		if (device_register(bcm47xx_bus.bcma.dev))
+			pr_err("Failed to register SoC device\n");
+		bcma_bus_register(&bcm47xx_bus.bcma.bus);
+		break;
+#endif
+	}
+	bcm47xx_buttons_register();
+	bcm47xx_leds_register();
+	bcm47xx_workarounds();
+
+	fixed_phy_add(PHY_POLL, 0, &bcm47xx_fixed_phy_status);
+	return 0;
+}
+device_initcall(bcm47xx_register_bus_complete);
diff --git a/arch/mips/bcm47xx/time.c b/arch/mips/bcm47xx/time.c
new file mode 100644
index 000000000..74224cf2e
--- /dev/null
+++ b/arch/mips/bcm47xx/time.c
@@ -0,0 +1,81 @@
+/*
+ *  Copyright (C) 2004 Florian Schirmer <jolt@tuxbox.org>
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/init.h>
+#include <linux/ssb/ssb.h>
+#include <asm/time.h>
+#include <bcm47xx.h>
+#include <bcm47xx_board.h>
+
+void __init plat_time_init(void)
+{
+	unsigned long hz = 0;
+	u16 chip_id = 0;
+	char buf[10];
+	int len;
+	enum bcm47xx_board board = bcm47xx_board_get();
+
+	/*
+	 * Use deterministic values for initial counter interrupt
+	 * so that calibrate delay avoids encountering a counter wrap.
+	 */
+	write_c0_count(0);
+	write_c0_compare(0xffff);
+
+	switch (bcm47xx_bus_type) {
+#ifdef CONFIG_BCM47XX_SSB
+	case BCM47XX_BUS_TYPE_SSB:
+		hz = ssb_cpu_clock(&bcm47xx_bus.ssb.mipscore) / 2;
+		chip_id = bcm47xx_bus.ssb.chip_id;
+		break;
+#endif
+#ifdef CONFIG_BCM47XX_BCMA
+	case BCM47XX_BUS_TYPE_BCMA:
+		hz = bcma_cpu_clock(&bcm47xx_bus.bcma.bus.drv_mips) / 2;
+		chip_id = bcm47xx_bus.bcma.bus.chipinfo.id;
+		break;
+#endif
+	}
+
+	if (chip_id == 0x5354) {
+		len = bcm47xx_nvram_getenv("clkfreq", buf, sizeof(buf));
+		if (len >= 0 && !strncmp(buf, "200", 4))
+			hz = 100000000;
+	}
+
+	switch (board) {
+	case BCM47XX_BOARD_ASUS_WL520GC:
+	case BCM47XX_BOARD_ASUS_WL520GU:
+		hz = 100000000;
+		break;
+	default:
+		break;
+	}
+
+	if (!hz)
+		hz = 100000000;
+
+	/* Set MIPS counter frequency for fixed_rate_gettimeoffset() */
+	mips_hpt_frequency = hz;
+}
diff --git a/arch/mips/bcm47xx/workarounds.c b/arch/mips/bcm47xx/workarounds.c
new file mode 100644
index 000000000..745c6228e
--- /dev/null
+++ b/arch/mips/bcm47xx/workarounds.c
@@ -0,0 +1,36 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "bcm47xx_private.h"
+
+#include <linux/gpio.h>
+#include <bcm47xx_board.h>
+#include <bcm47xx.h>
+
+static void __init bcm47xx_workarounds_enable_usb_power(int usb_power)
+{
+	int err;
+
+	err = gpio_request_one(usb_power, GPIOF_OUT_INIT_HIGH, "usb_power");
+	if (err)
+		pr_err("Failed to request USB power gpio: %d\n", err);
+	else
+		gpio_free(usb_power);
+}
+
+void __init bcm47xx_workarounds(void)
+{
+	enum bcm47xx_board board = bcm47xx_board_get();
+
+	switch (board) {
+	case BCM47XX_BOARD_NETGEAR_WNR3500L:
+	case BCM47XX_BOARD_NETGEAR_WNR3500L_V2:
+		bcm47xx_workarounds_enable_usb_power(12);
+		break;
+	case BCM47XX_BOARD_NETGEAR_WNDR3400V2:
+	case BCM47XX_BOARD_NETGEAR_WNDR3400_V3:
+		bcm47xx_workarounds_enable_usb_power(21);
+		break;
+	default:
+		/* No workaround(s) needed */
+		break;
+	}
+}
diff --git a/arch/mips/bcm63xx/Kconfig b/arch/mips/bcm63xx/Kconfig
new file mode 100644
index 000000000..837f6e5a2
--- /dev/null
+++ b/arch/mips/bcm63xx/Kconfig
@@ -0,0 +1,45 @@
+# SPDX-License-Identifier: GPL-2.0
+menu "CPU support"
+	depends on BCM63XX
+
+config BCM63XX_CPU_3368
+	bool "support 3368 CPU"
+	select SYS_HAS_CPU_BMIPS4350
+	select HAVE_PCI
+
+config BCM63XX_CPU_6328
+	bool "support 6328 CPU"
+	select SYS_HAS_CPU_BMIPS4350
+	select HAVE_PCI
+
+config BCM63XX_CPU_6338
+	bool "support 6338 CPU"
+	select SYS_HAS_CPU_BMIPS32_3300
+	select HAVE_PCI
+
+config BCM63XX_CPU_6345
+	bool "support 6345 CPU"
+	select SYS_HAS_CPU_BMIPS32_3300
+
+config BCM63XX_CPU_6348
+	bool "support 6348 CPU"
+	select SYS_HAS_CPU_BMIPS32_3300
+	select HAVE_PCI
+
+config BCM63XX_CPU_6358
+	bool "support 6358 CPU"
+	select SYS_HAS_CPU_BMIPS4350
+	select HAVE_PCI
+
+config BCM63XX_CPU_6362
+	bool "support 6362 CPU"
+	select SYS_HAS_CPU_BMIPS4350
+	select HAVE_PCI
+
+config BCM63XX_CPU_6368
+	bool "support 6368 CPU"
+	select SYS_HAS_CPU_BMIPS4350
+	select HAVE_PCI
+endmenu
+
+source "arch/mips/bcm63xx/boards/Kconfig"
diff --git a/arch/mips/bcm63xx/Makefile b/arch/mips/bcm63xx/Makefile
new file mode 100644
index 000000000..d89651e53
--- /dev/null
+++ b/arch/mips/bcm63xx/Makefile
@@ -0,0 +1,8 @@
+# SPDX-License-Identifier: GPL-2.0
+obj-y		+= clk.o cpu.o cs.o gpio.o irq.o nvram.o prom.o reset.o \
+		   setup.o timer.o dev-enet.o dev-flash.o dev-pcmcia.o \
+		   dev-rng.o dev-spi.o dev-hsspi.o dev-uart.o dev-wdt.o \
+		   dev-usb-usbd.o
+obj-$(CONFIG_EARLY_PRINTK)	+= early_printk.o
+
+obj-y		+= boards/
diff --git a/arch/mips/bcm63xx/Platform b/arch/mips/bcm63xx/Platform
new file mode 100644
index 000000000..882dc40f4
--- /dev/null
+++ b/arch/mips/bcm63xx/Platform
@@ -0,0 +1,6 @@
+#
+# Broadcom BCM63XX boards
+#
+cflags-$(CONFIG_BCM63XX)	+=					\
+		-I$(srctree)/arch/mips/include/asm/mach-bcm63xx/
+load-$(CONFIG_BCM63XX)		:= 0xffffffff80010000
diff --git a/arch/mips/bcm63xx/boards/Kconfig b/arch/mips/bcm63xx/boards/Kconfig
new file mode 100644
index 000000000..492c3bd00
--- /dev/null
+++ b/arch/mips/bcm63xx/boards/Kconfig
@@ -0,0 +1,11 @@
+# SPDX-License-Identifier: GPL-2.0
+choice
+	prompt "Board support"
+	depends on BCM63XX
+	default BOARD_BCM963XX
+
+config BOARD_BCM963XX
+	bool "Generic Broadcom 963xx boards"
+	select SSB
+
+endchoice
diff --git a/arch/mips/bcm63xx/boards/Makefile b/arch/mips/bcm63xx/boards/Makefile
new file mode 100644
index 000000000..a74b9c8d0
--- /dev/null
+++ b/arch/mips/bcm63xx/boards/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0-only
+obj-$(CONFIG_BOARD_BCM963XX)		+= board_bcm963xx.o
diff --git a/arch/mips/bcm63xx/boards/board_bcm963xx.c b/arch/mips/bcm63xx/boards/board_bcm963xx.c
new file mode 100644
index 000000000..01aff80a5
--- /dev/null
+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
@@ -0,0 +1,911 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ * Copyright (C) 2008 Florian Fainelli <florian@openwrt.org>
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <linux/platform_device.h>
+#include <linux/ssb/ssb.h>
+#include <asm/addrspace.h>
+#include <bcm63xx_board.h>
+#include <bcm63xx_cpu.h>
+#include <bcm63xx_dev_uart.h>
+#include <bcm63xx_regs.h>
+#include <bcm63xx_io.h>
+#include <bcm63xx_nvram.h>
+#include <bcm63xx_dev_pci.h>
+#include <bcm63xx_dev_enet.h>
+#include <bcm63xx_dev_flash.h>
+#include <bcm63xx_dev_hsspi.h>
+#include <bcm63xx_dev_pcmcia.h>
+#include <bcm63xx_dev_spi.h>
+#include <bcm63xx_dev_usb_usbd.h>
+#include <board_bcm963xx.h>
+
+#include <uapi/linux/bcm933xx_hcs.h>
+
+#define HCS_OFFSET_128K			0x20000
+
+static struct board_info board;
+
+/*
+ * known 3368 boards
+ */
+#ifdef CONFIG_BCM63XX_CPU_3368
+static struct board_info __initdata board_cvg834g = {
+	.name = "CVG834G_E15R3921",
+	.expected_cpu_id = 0x3368,
+
+	.ephy_reset_gpio = 36,
+	.ephy_reset_gpio_flags = GPIOF_INIT_HIGH,
+	.has_pci = 1,
+	.has_uart0 = 1,
+	.has_uart1 = 1,
+
+	.has_enet0 = 1,
+	.enet0 = {
+		.has_phy = 1,
+		.use_internal_phy = 1,
+	},
+
+	.leds = {
+		{
+			.name = "CVG834G:green:power",
+			.gpio = 37,
+			.default_trigger= "default-on",
+		},
+	},
+};
+#endif /* CONFIG_BCM63XX_CPU_3368 */
+
+/*
+ * known 6328 boards
+ */
+#ifdef CONFIG_BCM63XX_CPU_6328
+static struct board_info __initdata board_96328avng = {
+	.name = "96328avng",
+	.expected_cpu_id = 0x6328,
+
+	.has_pci = 1,
+	.has_uart0 = 1,
+
+	.has_usbd = 0,
+	.usbd = {
+		.use_fullspeed = 0,
+		.port_no = 0,
+	},
+
+	.leds = {
+		{
+			.name = "96328avng::ppp-fail",
+			.gpio = 2,
+			.active_low = 1,
+		},
+		{
+			.name = "96328avng::power",
+			.gpio = 4,
+			.active_low = 1,
+			.default_trigger = "default-on",
+		},
+		{
+			.name = "96328avng::power-fail",
+			.gpio = 8,
+			.active_low = 1,
+		},
+		{
+			.name = "96328avng::wps",
+			.gpio = 9,
+			.active_low = 1,
+		},
+		{
+			.name = "96328avng::ppp",
+			.gpio = 11,
+			.active_low = 1,
+		},
+	},
+};
+#endif /* CONFIG_BCM63XX_CPU_6328 */
+
+/*
+ * known 6338 boards
+ */
+#ifdef CONFIG_BCM63XX_CPU_6338
+static struct board_info __initdata board_96338gw = {
+	.name = "96338GW",
+	.expected_cpu_id = 0x6338,
+
+	.has_ohci0 = 1,
+	.has_uart0 = 1,
+
+	.has_enet0 = 1,
+	.enet0 = {
+		.force_speed_100 = 1,
+		.force_duplex_full = 1,
+	},
+
+	.leds = {
+		{
+			.name = "adsl",
+			.gpio = 3,
+			.active_low = 1,
+		},
+		{
+			.name = "ses",
+			.gpio = 5,
+			.active_low = 1,
+		},
+		{
+			.name = "ppp-fail",
+			.gpio = 4,
+			.active_low = 1,
+		},
+		{
+			.name = "power",
+			.gpio = 0,
+			.active_low = 1,
+			.default_trigger = "default-on",
+		},
+		{
+			.name = "stop",
+			.gpio = 1,
+			.active_low = 1,
+		}
+	},
+};
+
+static struct board_info __initdata board_96338w = {
+	.name = "96338W",
+	.expected_cpu_id = 0x6338,
+
+	.has_uart0 = 1,
+
+	.has_enet0 = 1,
+	.enet0 = {
+		.force_speed_100 = 1,
+		.force_duplex_full = 1,
+	},
+
+	.leds = {
+		{
+			.name = "adsl",
+			.gpio = 3,
+			.active_low = 1,
+		},
+		{
+			.name = "ses",
+			.gpio = 5,
+			.active_low = 1,
+		},
+		{
+			.name = "ppp-fail",
+			.gpio = 4,
+			.active_low = 1,
+		},
+		{
+			.name = "power",
+			.gpio = 0,
+			.active_low = 1,
+			.default_trigger = "default-on",
+		},
+		{
+			.name = "stop",
+			.gpio = 1,
+			.active_low = 1,
+		},
+	},
+};
+#endif /* CONFIG_BCM63XX_CPU_6338 */
+
+/*
+ * known 6345 boards
+ */
+#ifdef CONFIG_BCM63XX_CPU_6345
+static struct board_info __initdata board_96345gw2 = {
+	.name = "96345GW2",
+	.expected_cpu_id = 0x6345,
+
+	.has_uart0 = 1,
+};
+#endif /* CONFIG_BCM63XX_CPU_6345 */
+
+/*
+ * known 6348 boards
+ */
+#ifdef CONFIG_BCM63XX_CPU_6348
+static struct board_info __initdata board_96348r = {
+	.name = "96348R",
+	.expected_cpu_id = 0x6348,
+
+	.has_pci = 1,
+	.has_uart0 = 1,
+
+	.has_enet0 = 1,
+	.enet0 = {
+		.has_phy = 1,
+		.use_internal_phy = 1,
+	},
+
+	.leds = {
+		{
+			.name = "adsl-fail",
+			.gpio = 2,
+			.active_low = 1,
+		},
+		{
+			.name = "ppp",
+			.gpio = 3,
+			.active_low = 1,
+		},
+		{
+			.name = "ppp-fail",
+			.gpio = 4,
+			.active_low = 1,
+		},
+		{
+			.name = "power",
+			.gpio = 0,
+			.active_low = 1,
+			.default_trigger = "default-on",
+
+		},
+		{
+			.name = "stop",
+			.gpio = 1,
+			.active_low = 1,
+		},
+	},
+};
+
+static struct board_info __initdata board_96348gw_10 = {
+	.name = "96348GW-10",
+	.expected_cpu_id = 0x6348,
+
+	.has_ohci0 = 1,
+	.has_pccard = 1,
+	.has_pci = 1,
+	.has_uart0 = 1,
+
+	.has_enet0 = 1,
+	.enet0 = {
+		.has_phy = 1,
+		.use_internal_phy = 1,
+	},
+
+	.has_enet1 = 1,
+	.enet1 = {
+		.force_speed_100 = 1,
+		.force_duplex_full = 1,
+	},
+
+	.leds = {
+		{
+			.name = "adsl-fail",
+			.gpio = 2,
+			.active_low = 1,
+		},
+		{
+			.name = "ppp",
+			.gpio = 3,
+			.active_low = 1,
+		},
+		{
+			.name = "ppp-fail",
+			.gpio = 4,
+			.active_low = 1,
+		},
+		{
+			.name = "power",
+			.gpio = 0,
+			.active_low = 1,
+			.default_trigger = "default-on",
+		},
+		{
+			.name = "stop",
+			.gpio = 1,
+			.active_low = 1,
+		},
+	},
+};
+
+static struct board_info __initdata board_96348gw_11 = {
+	.name = "96348GW-11",
+	.expected_cpu_id = 0x6348,
+
+	.has_ohci0 = 1,
+	.has_pccard = 1,
+	.has_pci = 1,
+	.has_uart0 = 1,
+
+	.has_enet0 = 1,
+	.enet0 = {
+		.has_phy = 1,
+		.use_internal_phy = 1,
+	},
+
+	.has_enet1 = 1,
+	.enet1 = {
+		.force_speed_100 = 1,
+		.force_duplex_full = 1,
+	},
+
+	.leds = {
+		{
+			.name = "adsl-fail",
+			.gpio = 2,
+			.active_low = 1,
+		},
+		{
+			.name = "ppp",
+			.gpio = 3,
+			.active_low = 1,
+		},
+		{
+			.name = "ppp-fail",
+			.gpio = 4,
+			.active_low = 1,
+		},
+		{
+			.name = "power",
+			.gpio = 0,
+			.active_low = 1,
+			.default_trigger = "default-on",
+		},
+		{
+			.name = "stop",
+			.gpio = 1,
+			.active_low = 1,
+		},
+	},
+};
+
+static struct board_info __initdata board_96348gw = {
+	.name = "96348GW",
+	.expected_cpu_id = 0x6348,
+
+	.has_ohci0 = 1,
+	.has_pci = 1,
+	.has_uart0 = 1,
+
+	.has_enet0 = 1,
+	.enet0 = {
+		.has_phy = 1,
+		.use_internal_phy = 1,
+	},
+
+	.has_enet1 = 1,
+	.enet1 = {
+		.force_speed_100 = 1,
+		.force_duplex_full = 1,
+	},
+
+	.leds = {
+		{
+			.name = "adsl-fail",
+			.gpio = 2,
+			.active_low = 1,
+		},
+		{
+			.name = "ppp",
+			.gpio = 3,
+			.active_low = 1,
+		},
+		{
+			.name = "ppp-fail",
+			.gpio = 4,
+			.active_low = 1,
+		},
+		{
+			.name = "power",
+			.gpio = 0,
+			.active_low = 1,
+			.default_trigger = "default-on",
+		},
+		{
+			.name = "stop",
+			.gpio = 1,
+			.active_low = 1,
+		},
+	},
+};
+
+static struct board_info __initdata board_FAST2404 = {
+	.name = "F@ST2404",
+	.expected_cpu_id = 0x6348,
+
+	.has_ohci0 = 1,
+	.has_pccard = 1,
+	.has_pci = 1,
+	.has_uart0 = 1,
+
+	.has_enet0 = 1,
+	.enet0 = {
+		.has_phy = 1,
+		.use_internal_phy = 1,
+	},
+
+	.has_enet1 = 1,
+	.enet1 = {
+		.force_speed_100 = 1,
+		.force_duplex_full = 1,
+	},
+};
+
+static struct board_info __initdata board_rta1025w_16 = {
+	.name = "RTA1025W_16",
+	.expected_cpu_id = 0x6348,
+
+	.has_pci = 1,
+
+	.has_enet0 = 1,
+	.enet0 = {
+		.has_phy = 1,
+		.use_internal_phy = 1,
+	},
+
+	.has_enet1 = 1,
+	.enet1 = {
+		.force_speed_100 = 1,
+		.force_duplex_full = 1,
+	},
+};
+
+static struct board_info __initdata board_DV201AMR = {
+	.name = "DV201AMR",
+	.expected_cpu_id = 0x6348,
+
+	.has_ohci0 = 1,
+	.has_pci = 1,
+	.has_uart0 = 1,
+
+	.has_enet0 = 1,
+	.enet0 = {
+		.has_phy = 1,
+		.use_internal_phy = 1,
+	},
+
+	.has_enet1 = 1,
+	.enet1 = {
+		.force_speed_100 = 1,
+		.force_duplex_full = 1,
+	},
+};
+
+static struct board_info __initdata board_96348gw_a = {
+	.name = "96348GW-A",
+	.expected_cpu_id = 0x6348,
+
+	.has_ohci0 = 1,
+	.has_pci = 1,
+	.has_uart0 = 1,
+
+	.has_enet0 = 1,
+	.enet0 = {
+		.has_phy = 1,
+		.use_internal_phy = 1,
+	},
+
+	.has_enet1 = 1,
+	.enet1 = {
+		.force_speed_100 = 1,
+		.force_duplex_full = 1,
+	},
+};
+#endif /* CONFIG_BCM63XX_CPU_6348 */
+
+/*
+ * known 6358 boards
+ */
+#ifdef CONFIG_BCM63XX_CPU_6358
+static struct board_info __initdata board_96358vw = {
+	.name = "96358VW",
+	.expected_cpu_id = 0x6358,
+
+	.has_ehci0 = 1,
+	.has_ohci0 = 1,
+	.has_pccard = 1,
+	.has_pci = 1,
+	.has_uart0 = 1,
+
+	.has_enet0 = 1,
+	.enet0 = {
+		.has_phy = 1,
+		.use_internal_phy = 1,
+	},
+
+	.has_enet1 = 1,
+	.enet1 = {
+		.force_speed_100 = 1,
+		.force_duplex_full = 1,
+	},
+
+	.leds = {
+		{
+			.name = "adsl-fail",
+			.gpio = 15,
+			.active_low = 1,
+		},
+		{
+			.name = "ppp",
+			.gpio = 22,
+			.active_low = 1,
+		},
+		{
+			.name = "ppp-fail",
+			.gpio = 23,
+			.active_low = 1,
+		},
+		{
+			.name = "power",
+			.gpio = 4,
+			.default_trigger = "default-on",
+		},
+		{
+			.name = "stop",
+			.gpio = 5,
+		},
+	},
+};
+
+static struct board_info __initdata board_96358vw2 = {
+	.name = "96358VW2",
+	.expected_cpu_id = 0x6358,
+
+	.has_ehci0 = 1,
+	.has_ohci0 = 1,
+	.has_pccard = 1,
+	.has_pci = 1,
+	.has_uart0 = 1,
+
+	.has_enet0 = 1,
+	.enet0 = {
+		.has_phy = 1,
+		.use_internal_phy = 1,
+	},
+
+	.has_enet1 = 1,
+	.enet1 = {
+		.force_speed_100 = 1,
+		.force_duplex_full = 1,
+	},
+
+	.leds = {
+		{
+			.name = "adsl",
+			.gpio = 22,
+			.active_low = 1,
+		},
+		{
+			.name = "ppp-fail",
+			.gpio = 23,
+		},
+		{
+			.name = "power",
+			.gpio = 5,
+			.active_low = 1,
+			.default_trigger = "default-on",
+		},
+		{
+			.name = "stop",
+			.gpio = 4,
+			.active_low = 1,
+		},
+	},
+};
+
+static struct board_info __initdata board_AGPFS0 = {
+	.name = "AGPF-S0",
+	.expected_cpu_id = 0x6358,
+
+	.has_ehci0 = 1,
+	.has_ohci0 = 1,
+	.has_pci = 1,
+	.has_uart0 = 1,
+
+	.has_enet0 = 1,
+	.enet0 = {
+		.has_phy = 1,
+		.use_internal_phy = 1,
+	},
+
+	.has_enet1 = 1,
+	.enet1 = {
+		.force_speed_100 = 1,
+		.force_duplex_full = 1,
+	},
+};
+
+static struct board_info __initdata board_DWVS0 = {
+	.name = "DWV-S0",
+	.expected_cpu_id = 0x6358,
+
+	.has_ehci0 = 1,
+	.has_ohci0 = 1,
+	.has_pci = 1,
+
+	.has_enet0 = 1,
+	.enet0 = {
+		.has_phy = 1,
+		.use_internal_phy = 1,
+	},
+
+	.has_enet1 = 1,
+	.enet1 = {
+		.force_speed_100 = 1,
+		.force_duplex_full = 1,
+	},
+};
+#endif /* CONFIG_BCM63XX_CPU_6358 */
+
+/*
+ * all boards
+ */
+static const struct board_info __initconst *bcm963xx_boards[] = {
+#ifdef CONFIG_BCM63XX_CPU_3368
+	&board_cvg834g,
+#endif /* CONFIG_BCM63XX_CPU_3368 */
+#ifdef CONFIG_BCM63XX_CPU_6328
+	&board_96328avng,
+#endif /* CONFIG_BCM63XX_CPU_6328 */
+#ifdef CONFIG_BCM63XX_CPU_6338
+	&board_96338gw,
+	&board_96338w,
+#endif /* CONFIG_BCM63XX_CPU_6338 */
+#ifdef CONFIG_BCM63XX_CPU_6345
+	&board_96345gw2,
+#endif /* CONFIG_BCM63XX_CPU_6345 */
+#ifdef CONFIG_BCM63XX_CPU_6348
+	&board_96348r,
+	&board_96348gw,
+	&board_96348gw_10,
+	&board_96348gw_11,
+	&board_FAST2404,
+	&board_DV201AMR,
+	&board_96348gw_a,
+	&board_rta1025w_16,
+#endif /* CONFIG_BCM63XX_CPU_6348 */
+#ifdef CONFIG_BCM63XX_CPU_6358
+	&board_96358vw,
+	&board_96358vw2,
+	&board_AGPFS0,
+	&board_DWVS0,
+#endif /* CONFIG_BCM63XX_CPU_6358 */
+};
+
+/*
+ * Register a sane SPROMv2 to make the on-board
+ * bcm4318 WLAN work
+ */
+#ifdef CONFIG_SSB_PCIHOST
+static struct ssb_sprom bcm63xx_sprom = {
+	.revision		= 0x02,
+	.board_rev		= 0x17,
+	.country_code		= 0x0,
+	.ant_available_bg	= 0x3,
+	.pa0b0			= 0x15ae,
+	.pa0b1			= 0xfa85,
+	.pa0b2			= 0xfe8d,
+	.pa1b0			= 0xffff,
+	.pa1b1			= 0xffff,
+	.pa1b2			= 0xffff,
+	.gpio0			= 0xff,
+	.gpio1			= 0xff,
+	.gpio2			= 0xff,
+	.gpio3			= 0xff,
+	.maxpwr_bg		= 0x004c,
+	.itssi_bg		= 0x00,
+	.boardflags_lo		= 0x2848,
+	.boardflags_hi		= 0x0000,
+};
+
+int bcm63xx_get_fallback_sprom(struct ssb_bus *bus, struct ssb_sprom *out)
+{
+	if (bus->bustype == SSB_BUSTYPE_PCI) {
+		memcpy(out, &bcm63xx_sprom, sizeof(struct ssb_sprom));
+		return 0;
+	} else {
+		pr_err("unable to fill SPROM for given bustype\n");
+		return -EINVAL;
+	}
+}
+#endif /* CONFIG_SSB_PCIHOST */
+
+/*
+ * return board name for /proc/cpuinfo
+ */
+const char *board_get_name(void)
+{
+	return board.name;
+}
+
+/*
+ * early init callback, read nvram data from flash and checksum it
+ */
+void __init board_prom_init(void)
+{
+	unsigned int i;
+	u8 *boot_addr, *cfe;
+	char cfe_version[32];
+	char *board_name = NULL;
+	u32 val;
+	struct bcm_hcs *hcs;
+
+	/* read base address of boot chip select (0)
+	 * 6328/6362 do not have MPI but boot from a fixed address
+	 */
+	if (BCMCPU_IS_6328() || BCMCPU_IS_6362()) {
+		val = 0x18000000;
+	} else {
+		val = bcm_mpi_readl(MPI_CSBASE_REG(0));
+		val &= MPI_CSBASE_BASE_MASK;
+	}
+	boot_addr = (u8 *)KSEG1ADDR(val);
+
+	/* dump cfe version */
+	cfe = boot_addr + BCM963XX_CFE_VERSION_OFFSET;
+	if (strstarts(cfe, "cfe-")) {
+		if(cfe[4] == 'v') {
+			if(cfe[5] == 'd')
+				snprintf(cfe_version, 11, "%s",
+					 (char *) &cfe[5]);
+			else if (cfe[10] > 0)
+				snprintf(cfe_version, sizeof(cfe_version),
+					 "%u.%u.%u-%u.%u-%u", cfe[5], cfe[6],
+					 cfe[7], cfe[8], cfe[9], cfe[10]);
+			else
+				snprintf(cfe_version, sizeof(cfe_version),
+					 "%u.%u.%u-%u.%u", cfe[5], cfe[6],
+					 cfe[7], cfe[8], cfe[9]);
+		} else {
+			snprintf(cfe_version, 12, "%s", (char *) &cfe[4]);
+		}
+	} else {
+		strcpy(cfe_version, "unknown");
+	}
+	pr_info("CFE version: %s\n", cfe_version);
+
+	bcm63xx_nvram_init(boot_addr + BCM963XX_NVRAM_OFFSET);
+
+	if (BCMCPU_IS_3368()) {
+		hcs = (struct bcm_hcs *)boot_addr;
+		board_name = hcs->filename;
+	} else {
+		board_name = bcm63xx_nvram_get_name();
+	}
+	/* find board by name */
+	for (i = 0; i < ARRAY_SIZE(bcm963xx_boards); i++) {
+		if (strncmp(board_name, bcm963xx_boards[i]->name, 16))
+			continue;
+		/* copy, board desc array is marked initdata */
+		memcpy(&board, bcm963xx_boards[i], sizeof(board));
+		break;
+	}
+
+	/* bail out if board is not found, will complain later */
+	if (!board.name[0]) {
+		char name[17];
+		memcpy(name, board_name, 16);
+		name[16] = 0;
+		pr_err("unknown bcm963xx board: %s\n", name);
+		return;
+	}
+
+	/* setup pin multiplexing depending on board enabled device,
+	 * this has to be done this early since PCI init is done
+	 * inside arch_initcall */
+	val = 0;
+
+#ifdef CONFIG_PCI
+	if (board.has_pci) {
+		bcm63xx_pci_enabled = 1;
+		if (BCMCPU_IS_6348())
+			val |= GPIO_MODE_6348_G2_PCI;
+	}
+#endif /* CONFIG_PCI */
+
+	if (board.has_pccard) {
+		if (BCMCPU_IS_6348())
+			val |= GPIO_MODE_6348_G1_MII_PCCARD;
+	}
+
+	if (board.has_enet0 && !board.enet0.use_internal_phy) {
+		if (BCMCPU_IS_6348())
+			val |= GPIO_MODE_6348_G3_EXT_MII |
+				GPIO_MODE_6348_G0_EXT_MII;
+	}
+
+	if (board.has_enet1 && !board.enet1.use_internal_phy) {
+		if (BCMCPU_IS_6348())
+			val |= GPIO_MODE_6348_G3_EXT_MII |
+				GPIO_MODE_6348_G0_EXT_MII;
+	}
+
+	bcm_gpio_writel(val, GPIO_MODE_REG);
+}
+
+/*
+ * second stage init callback, good time to panic if we couldn't
+ * identify on which board we're running since early printk is working
+ */
+void __init board_setup(void)
+{
+	if (!board.name[0])
+		panic("unable to detect bcm963xx board");
+	pr_info("board name: %s\n", board.name);
+
+	/* make sure we're running on expected cpu */
+	if (bcm63xx_get_cpu_id() != board.expected_cpu_id)
+		panic("unexpected CPU for bcm963xx board");
+}
+
+static struct gpio_led_platform_data bcm63xx_led_data;
+
+static struct platform_device bcm63xx_gpio_leds = {
+	.name			= "leds-gpio",
+	.id			= 0,
+	.dev.platform_data	= &bcm63xx_led_data,
+};
+
+/*
+ * third stage init callback, register all board devices.
+ */
+int __init board_register_devices(void)
+{
+	if (board.has_uart0)
+		bcm63xx_uart_register(0);
+
+	if (board.has_uart1)
+		bcm63xx_uart_register(1);
+
+	if (board.has_pccard)
+		bcm63xx_pcmcia_register();
+
+	if (board.has_enet0 &&
+	    !bcm63xx_nvram_get_mac_address(board.enet0.mac_addr))
+		bcm63xx_enet_register(0, &board.enet0);
+
+	if (board.has_enet1 &&
+	    !bcm63xx_nvram_get_mac_address(board.enet1.mac_addr))
+		bcm63xx_enet_register(1, &board.enet1);
+
+	if (board.has_enetsw &&
+	    !bcm63xx_nvram_get_mac_address(board.enetsw.mac_addr))
+		bcm63xx_enetsw_register(&board.enetsw);
+
+	if (board.has_usbd)
+		bcm63xx_usbd_register(&board.usbd);
+
+	/* Generate MAC address for WLAN and register our SPROM,
+	 * do this after registering enet devices
+	 */
+#ifdef CONFIG_SSB_PCIHOST
+	if (!bcm63xx_nvram_get_mac_address(bcm63xx_sprom.il0mac)) {
+		memcpy(bcm63xx_sprom.et0mac, bcm63xx_sprom.il0mac, ETH_ALEN);
+		memcpy(bcm63xx_sprom.et1mac, bcm63xx_sprom.il0mac, ETH_ALEN);
+		if (ssb_arch_register_fallback_sprom(
+				&bcm63xx_get_fallback_sprom) < 0)
+			pr_err("failed to register fallback SPROM\n");
+	}
+#endif /* CONFIG_SSB_PCIHOST */
+
+	bcm63xx_spi_register();
+
+	bcm63xx_hsspi_register();
+
+	bcm63xx_flash_register();
+
+	bcm63xx_led_data.num_leds = ARRAY_SIZE(board.leds);
+	bcm63xx_led_data.leds = board.leds;
+
+	platform_device_register(&bcm63xx_gpio_leds);
+
+	if (board.ephy_reset_gpio && board.ephy_reset_gpio_flags)
+		gpio_request_one(board.ephy_reset_gpio,
+				board.ephy_reset_gpio_flags, "ephy-reset");
+
+	return 0;
+}
diff --git a/arch/mips/bcm63xx/clk.c b/arch/mips/bcm63xx/clk.c
new file mode 100644
index 000000000..86a6e2590
--- /dev/null
+++ b/arch/mips/bcm63xx/clk.c
@@ -0,0 +1,579 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ */
+
+#include <linux/init.h>
+#include <linux/export.h>
+#include <linux/mutex.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+#include <linux/clkdev.h>
+#include <linux/delay.h>
+#include <bcm63xx_cpu.h>
+#include <bcm63xx_io.h>
+#include <bcm63xx_regs.h>
+#include <bcm63xx_reset.h>
+
+struct clk {
+	void		(*set)(struct clk *, int);
+	unsigned int	rate;
+	unsigned int	usage;
+	int		id;
+};
+
+static DEFINE_MUTEX(clocks_mutex);
+
+
+static void clk_enable_unlocked(struct clk *clk)
+{
+	if (clk->set && (clk->usage++) == 0)
+		clk->set(clk, 1);
+}
+
+static void clk_disable_unlocked(struct clk *clk)
+{
+	if (clk->set && (--clk->usage) == 0)
+		clk->set(clk, 0);
+}
+
+static void bcm_hwclock_set(u32 mask, int enable)
+{
+	u32 reg;
+
+	reg = bcm_perf_readl(PERF_CKCTL_REG);
+	if (enable)
+		reg |= mask;
+	else
+		reg &= ~mask;
+	bcm_perf_writel(reg, PERF_CKCTL_REG);
+}
+
+/*
+ * Ethernet MAC "misc" clock: dma clocks and main clock on 6348
+ */
+static void enet_misc_set(struct clk *clk, int enable)
+{
+	u32 mask;
+
+	if (BCMCPU_IS_6338())
+		mask = CKCTL_6338_ENET_EN;
+	else if (BCMCPU_IS_6345())
+		mask = CKCTL_6345_ENET_EN;
+	else if (BCMCPU_IS_6348())
+		mask = CKCTL_6348_ENET_EN;
+	else
+		/* BCMCPU_IS_6358 */
+		mask = CKCTL_6358_EMUSB_EN;
+	bcm_hwclock_set(mask, enable);
+}
+
+static struct clk clk_enet_misc = {
+	.set	= enet_misc_set,
+};
+
+/*
+ * Ethernet MAC clocks: only relevant on 6358, silently enable misc
+ * clocks
+ */
+static void enetx_set(struct clk *clk, int enable)
+{
+	if (enable)
+		clk_enable_unlocked(&clk_enet_misc);
+	else
+		clk_disable_unlocked(&clk_enet_misc);
+
+	if (BCMCPU_IS_3368() || BCMCPU_IS_6358()) {
+		u32 mask;
+
+		if (clk->id == 0)
+			mask = CKCTL_6358_ENET0_EN;
+		else
+			mask = CKCTL_6358_ENET1_EN;
+		bcm_hwclock_set(mask, enable);
+	}
+}
+
+static struct clk clk_enet0 = {
+	.id	= 0,
+	.set	= enetx_set,
+};
+
+static struct clk clk_enet1 = {
+	.id	= 1,
+	.set	= enetx_set,
+};
+
+/*
+ * Ethernet PHY clock
+ */
+static void ephy_set(struct clk *clk, int enable)
+{
+	if (BCMCPU_IS_3368() || BCMCPU_IS_6358())
+		bcm_hwclock_set(CKCTL_6358_EPHY_EN, enable);
+}
+
+
+static struct clk clk_ephy = {
+	.set	= ephy_set,
+};
+
+/*
+ * Ethernet switch SAR clock
+ */
+static void swpkt_sar_set(struct clk *clk, int enable)
+{
+	if (BCMCPU_IS_6368())
+		bcm_hwclock_set(CKCTL_6368_SWPKT_SAR_EN, enable);
+	else
+		return;
+}
+
+static struct clk clk_swpkt_sar = {
+	.set	= swpkt_sar_set,
+};
+
+/*
+ * Ethernet switch USB clock
+ */
+static void swpkt_usb_set(struct clk *clk, int enable)
+{
+	if (BCMCPU_IS_6368())
+		bcm_hwclock_set(CKCTL_6368_SWPKT_USB_EN, enable);
+	else
+		return;
+}
+
+static struct clk clk_swpkt_usb = {
+	.set	= swpkt_usb_set,
+};
+
+/*
+ * Ethernet switch clock
+ */
+static void enetsw_set(struct clk *clk, int enable)
+{
+	if (BCMCPU_IS_6328()) {
+		bcm_hwclock_set(CKCTL_6328_ROBOSW_EN, enable);
+	} else if (BCMCPU_IS_6362()) {
+		bcm_hwclock_set(CKCTL_6362_ROBOSW_EN, enable);
+	} else if (BCMCPU_IS_6368()) {
+		if (enable) {
+			clk_enable_unlocked(&clk_swpkt_sar);
+			clk_enable_unlocked(&clk_swpkt_usb);
+		} else {
+			clk_disable_unlocked(&clk_swpkt_usb);
+			clk_disable_unlocked(&clk_swpkt_sar);
+		}
+		bcm_hwclock_set(CKCTL_6368_ROBOSW_EN, enable);
+	} else {
+		return;
+	}
+
+	if (enable) {
+		/* reset switch core afer clock change */
+		bcm63xx_core_set_reset(BCM63XX_RESET_ENETSW, 1);
+		msleep(10);
+		bcm63xx_core_set_reset(BCM63XX_RESET_ENETSW, 0);
+		msleep(10);
+	}
+}
+
+static struct clk clk_enetsw = {
+	.set	= enetsw_set,
+};
+
+/*
+ * PCM clock
+ */
+static void pcm_set(struct clk *clk, int enable)
+{
+	if (BCMCPU_IS_3368())
+		bcm_hwclock_set(CKCTL_3368_PCM_EN, enable);
+	if (BCMCPU_IS_6358())
+		bcm_hwclock_set(CKCTL_6358_PCM_EN, enable);
+}
+
+static struct clk clk_pcm = {
+	.set	= pcm_set,
+};
+
+/*
+ * USB host clock
+ */
+static void usbh_set(struct clk *clk, int enable)
+{
+	if (BCMCPU_IS_6328())
+		bcm_hwclock_set(CKCTL_6328_USBH_EN, enable);
+	else if (BCMCPU_IS_6348())
+		bcm_hwclock_set(CKCTL_6348_USBH_EN, enable);
+	else if (BCMCPU_IS_6362())
+		bcm_hwclock_set(CKCTL_6362_USBH_EN, enable);
+	else if (BCMCPU_IS_6368())
+		bcm_hwclock_set(CKCTL_6368_USBH_EN, enable);
+}
+
+static struct clk clk_usbh = {
+	.set	= usbh_set,
+};
+
+/*
+ * USB device clock
+ */
+static void usbd_set(struct clk *clk, int enable)
+{
+	if (BCMCPU_IS_6328())
+		bcm_hwclock_set(CKCTL_6328_USBD_EN, enable);
+	else if (BCMCPU_IS_6362())
+		bcm_hwclock_set(CKCTL_6362_USBD_EN, enable);
+	else if (BCMCPU_IS_6368())
+		bcm_hwclock_set(CKCTL_6368_USBD_EN, enable);
+}
+
+static struct clk clk_usbd = {
+	.set	= usbd_set,
+};
+
+/*
+ * SPI clock
+ */
+static void spi_set(struct clk *clk, int enable)
+{
+	u32 mask;
+
+	if (BCMCPU_IS_6338())
+		mask = CKCTL_6338_SPI_EN;
+	else if (BCMCPU_IS_6348())
+		mask = CKCTL_6348_SPI_EN;
+	else if (BCMCPU_IS_3368() || BCMCPU_IS_6358())
+		mask = CKCTL_6358_SPI_EN;
+	else if (BCMCPU_IS_6362())
+		mask = CKCTL_6362_SPI_EN;
+	else
+		/* BCMCPU_IS_6368 */
+		mask = CKCTL_6368_SPI_EN;
+	bcm_hwclock_set(mask, enable);
+}
+
+static struct clk clk_spi = {
+	.set	= spi_set,
+};
+
+/*
+ * HSSPI clock
+ */
+static void hsspi_set(struct clk *clk, int enable)
+{
+	u32 mask;
+
+	if (BCMCPU_IS_6328())
+		mask = CKCTL_6328_HSSPI_EN;
+	else if (BCMCPU_IS_6362())
+		mask = CKCTL_6362_HSSPI_EN;
+	else
+		return;
+
+	bcm_hwclock_set(mask, enable);
+}
+
+static struct clk clk_hsspi = {
+	.set	= hsspi_set,
+};
+
+/*
+ * HSSPI PLL
+ */
+static struct clk clk_hsspi_pll;
+
+/*
+ * XTM clock
+ */
+static void xtm_set(struct clk *clk, int enable)
+{
+	if (!BCMCPU_IS_6368())
+		return;
+
+	if (enable)
+		clk_enable_unlocked(&clk_swpkt_sar);
+	else
+		clk_disable_unlocked(&clk_swpkt_sar);
+
+	bcm_hwclock_set(CKCTL_6368_SAR_EN, enable);
+
+	if (enable) {
+		/* reset sar core afer clock change */
+		bcm63xx_core_set_reset(BCM63XX_RESET_SAR, 1);
+		mdelay(1);
+		bcm63xx_core_set_reset(BCM63XX_RESET_SAR, 0);
+		mdelay(1);
+	}
+}
+
+
+static struct clk clk_xtm = {
+	.set	= xtm_set,
+};
+
+/*
+ * IPsec clock
+ */
+static void ipsec_set(struct clk *clk, int enable)
+{
+	if (BCMCPU_IS_6362())
+		bcm_hwclock_set(CKCTL_6362_IPSEC_EN, enable);
+	else if (BCMCPU_IS_6368())
+		bcm_hwclock_set(CKCTL_6368_IPSEC_EN, enable);
+}
+
+static struct clk clk_ipsec = {
+	.set	= ipsec_set,
+};
+
+/*
+ * PCIe clock
+ */
+
+static void pcie_set(struct clk *clk, int enable)
+{
+	if (BCMCPU_IS_6328())
+		bcm_hwclock_set(CKCTL_6328_PCIE_EN, enable);
+	else if (BCMCPU_IS_6362())
+		bcm_hwclock_set(CKCTL_6362_PCIE_EN, enable);
+}
+
+static struct clk clk_pcie = {
+	.set	= pcie_set,
+};
+
+/*
+ * Internal peripheral clock
+ */
+static struct clk clk_periph = {
+	.rate	= (50 * 1000 * 1000),
+};
+
+
+/*
+ * Linux clock API implementation
+ */
+int clk_enable(struct clk *clk)
+{
+	if (!clk)
+		return 0;
+	mutex_lock(&clocks_mutex);
+	clk_enable_unlocked(clk);
+	mutex_unlock(&clocks_mutex);
+	return 0;
+}
+
+EXPORT_SYMBOL(clk_enable);
+
+void clk_disable(struct clk *clk)
+{
+	if (!clk)
+		return;
+
+	mutex_lock(&clocks_mutex);
+	clk_disable_unlocked(clk);
+	mutex_unlock(&clocks_mutex);
+}
+
+EXPORT_SYMBOL(clk_disable);
+
+struct clk *clk_get_parent(struct clk *clk)
+{
+	return NULL;
+}
+EXPORT_SYMBOL(clk_get_parent);
+
+int clk_set_parent(struct clk *clk, struct clk *parent)
+{
+	return 0;
+}
+EXPORT_SYMBOL(clk_set_parent);
+
+unsigned long clk_get_rate(struct clk *clk)
+{
+	if (!clk)
+		return 0;
+
+	return clk->rate;
+}
+
+EXPORT_SYMBOL(clk_get_rate);
+
+int clk_set_rate(struct clk *clk, unsigned long rate)
+{
+	return 0;
+}
+EXPORT_SYMBOL_GPL(clk_set_rate);
+
+long clk_round_rate(struct clk *clk, unsigned long rate)
+{
+	return 0;
+}
+EXPORT_SYMBOL_GPL(clk_round_rate);
+
+static struct clk_lookup bcm3368_clks[] = {
+	/* fixed rate clocks */
+	CLKDEV_INIT(NULL, "periph", &clk_periph),
+	CLKDEV_INIT("bcm63xx_uart.0", "refclk", &clk_periph),
+	CLKDEV_INIT("bcm63xx_uart.1", "refclk", &clk_periph),
+	/* gated clocks */
+	CLKDEV_INIT(NULL, "enet0", &clk_enet0),
+	CLKDEV_INIT(NULL, "enet1", &clk_enet1),
+	CLKDEV_INIT(NULL, "ephy", &clk_ephy),
+	CLKDEV_INIT(NULL, "usbh", &clk_usbh),
+	CLKDEV_INIT(NULL, "usbd", &clk_usbd),
+	CLKDEV_INIT(NULL, "spi", &clk_spi),
+	CLKDEV_INIT(NULL, "pcm", &clk_pcm),
+	CLKDEV_INIT("bcm63xx_enet.0", "enet", &clk_enet0),
+	CLKDEV_INIT("bcm63xx_enet.1", "enet", &clk_enet1),
+};
+
+static struct clk_lookup bcm6328_clks[] = {
+	/* fixed rate clocks */
+	CLKDEV_INIT(NULL, "periph", &clk_periph),
+	CLKDEV_INIT("bcm63xx_uart.0", "refclk", &clk_periph),
+	CLKDEV_INIT("bcm63xx_uart.1", "refclk", &clk_periph),
+	CLKDEV_INIT("bcm63xx-hsspi.0", "pll", &clk_hsspi_pll),
+	/* gated clocks */
+	CLKDEV_INIT(NULL, "enetsw", &clk_enetsw),
+	CLKDEV_INIT(NULL, "usbh", &clk_usbh),
+	CLKDEV_INIT(NULL, "usbd", &clk_usbd),
+	CLKDEV_INIT(NULL, "hsspi", &clk_hsspi),
+	CLKDEV_INIT(NULL, "pcie", &clk_pcie),
+};
+
+static struct clk_lookup bcm6338_clks[] = {
+	/* fixed rate clocks */
+	CLKDEV_INIT(NULL, "periph", &clk_periph),
+	CLKDEV_INIT("bcm63xx_uart.0", "refclk", &clk_periph),
+	/* gated clocks */
+	CLKDEV_INIT(NULL, "enet0", &clk_enet0),
+	CLKDEV_INIT(NULL, "enet1", &clk_enet1),
+	CLKDEV_INIT(NULL, "ephy", &clk_ephy),
+	CLKDEV_INIT(NULL, "usbh", &clk_usbh),
+	CLKDEV_INIT(NULL, "usbd", &clk_usbd),
+	CLKDEV_INIT(NULL, "spi", &clk_spi),
+	CLKDEV_INIT("bcm63xx_enet.0", "enet", &clk_enet_misc),
+};
+
+static struct clk_lookup bcm6345_clks[] = {
+	/* fixed rate clocks */
+	CLKDEV_INIT(NULL, "periph", &clk_periph),
+	CLKDEV_INIT("bcm63xx_uart.0", "refclk", &clk_periph),
+	/* gated clocks */
+	CLKDEV_INIT(NULL, "enet0", &clk_enet0),
+	CLKDEV_INIT(NULL, "enet1", &clk_enet1),
+	CLKDEV_INIT(NULL, "ephy", &clk_ephy),
+	CLKDEV_INIT(NULL, "usbh", &clk_usbh),
+	CLKDEV_INIT(NULL, "usbd", &clk_usbd),
+	CLKDEV_INIT(NULL, "spi", &clk_spi),
+	CLKDEV_INIT("bcm63xx_enet.0", "enet", &clk_enet_misc),
+};
+
+static struct clk_lookup bcm6348_clks[] = {
+	/* fixed rate clocks */
+	CLKDEV_INIT(NULL, "periph", &clk_periph),
+	CLKDEV_INIT("bcm63xx_uart.0", "refclk", &clk_periph),
+	/* gated clocks */
+	CLKDEV_INIT(NULL, "enet0", &clk_enet0),
+	CLKDEV_INIT(NULL, "enet1", &clk_enet1),
+	CLKDEV_INIT(NULL, "ephy", &clk_ephy),
+	CLKDEV_INIT(NULL, "usbh", &clk_usbh),
+	CLKDEV_INIT(NULL, "usbd", &clk_usbd),
+	CLKDEV_INIT(NULL, "spi", &clk_spi),
+	CLKDEV_INIT("bcm63xx_enet.0", "enet", &clk_enet_misc),
+	CLKDEV_INIT("bcm63xx_enet.1", "enet", &clk_enet_misc),
+};
+
+static struct clk_lookup bcm6358_clks[] = {
+	/* fixed rate clocks */
+	CLKDEV_INIT(NULL, "periph", &clk_periph),
+	CLKDEV_INIT("bcm63xx_uart.0", "refclk", &clk_periph),
+	CLKDEV_INIT("bcm63xx_uart.1", "refclk", &clk_periph),
+	/* gated clocks */
+	CLKDEV_INIT(NULL, "enet0", &clk_enet0),
+	CLKDEV_INIT(NULL, "enet1", &clk_enet1),
+	CLKDEV_INIT(NULL, "ephy", &clk_ephy),
+	CLKDEV_INIT(NULL, "usbh", &clk_usbh),
+	CLKDEV_INIT(NULL, "usbd", &clk_usbd),
+	CLKDEV_INIT(NULL, "spi", &clk_spi),
+	CLKDEV_INIT(NULL, "pcm", &clk_pcm),
+	CLKDEV_INIT(NULL, "swpkt_sar", &clk_swpkt_sar),
+	CLKDEV_INIT(NULL, "swpkt_usb", &clk_swpkt_usb),
+	CLKDEV_INIT("bcm63xx_enet.0", "enet", &clk_enet0),
+	CLKDEV_INIT("bcm63xx_enet.1", "enet", &clk_enet1),
+};
+
+static struct clk_lookup bcm6362_clks[] = {
+	/* fixed rate clocks */
+	CLKDEV_INIT(NULL, "periph", &clk_periph),
+	CLKDEV_INIT("bcm63xx_uart.0", "refclk", &clk_periph),
+	CLKDEV_INIT("bcm63xx_uart.1", "refclk", &clk_periph),
+	CLKDEV_INIT("bcm63xx-hsspi.0", "pll", &clk_hsspi_pll),
+	/* gated clocks */
+	CLKDEV_INIT(NULL, "enetsw", &clk_enetsw),
+	CLKDEV_INIT(NULL, "usbh", &clk_usbh),
+	CLKDEV_INIT(NULL, "usbd", &clk_usbd),
+	CLKDEV_INIT(NULL, "spi", &clk_spi),
+	CLKDEV_INIT(NULL, "hsspi", &clk_hsspi),
+	CLKDEV_INIT(NULL, "pcie", &clk_pcie),
+	CLKDEV_INIT(NULL, "ipsec", &clk_ipsec),
+};
+
+static struct clk_lookup bcm6368_clks[] = {
+	/* fixed rate clocks */
+	CLKDEV_INIT(NULL, "periph", &clk_periph),
+	CLKDEV_INIT("bcm63xx_uart.0", "refclk", &clk_periph),
+	CLKDEV_INIT("bcm63xx_uart.1", "refclk", &clk_periph),
+	/* gated clocks */
+	CLKDEV_INIT(NULL, "enetsw", &clk_enetsw),
+	CLKDEV_INIT(NULL, "usbh", &clk_usbh),
+	CLKDEV_INIT(NULL, "usbd", &clk_usbd),
+	CLKDEV_INIT(NULL, "spi", &clk_spi),
+	CLKDEV_INIT(NULL, "xtm", &clk_xtm),
+	CLKDEV_INIT(NULL, "ipsec", &clk_ipsec),
+};
+
+#define HSSPI_PLL_HZ_6328	133333333
+#define HSSPI_PLL_HZ_6362	400000000
+
+static int __init bcm63xx_clk_init(void)
+{
+	switch (bcm63xx_get_cpu_id()) {
+	case BCM3368_CPU_ID:
+		clkdev_add_table(bcm3368_clks, ARRAY_SIZE(bcm3368_clks));
+		break;
+	case BCM6328_CPU_ID:
+		clk_hsspi_pll.rate = HSSPI_PLL_HZ_6328;
+		clkdev_add_table(bcm6328_clks, ARRAY_SIZE(bcm6328_clks));
+		break;
+	case BCM6338_CPU_ID:
+		clkdev_add_table(bcm6338_clks, ARRAY_SIZE(bcm6338_clks));
+		break;
+	case BCM6345_CPU_ID:
+		clkdev_add_table(bcm6345_clks, ARRAY_SIZE(bcm6345_clks));
+		break;
+	case BCM6348_CPU_ID:
+		clkdev_add_table(bcm6348_clks, ARRAY_SIZE(bcm6348_clks));
+		break;
+	case BCM6358_CPU_ID:
+		clkdev_add_table(bcm6358_clks, ARRAY_SIZE(bcm6358_clks));
+		break;
+	case BCM6362_CPU_ID:
+		clk_hsspi_pll.rate = HSSPI_PLL_HZ_6362;
+		clkdev_add_table(bcm6362_clks, ARRAY_SIZE(bcm6362_clks));
+		break;
+	case BCM6368_CPU_ID:
+		clkdev_add_table(bcm6368_clks, ARRAY_SIZE(bcm6368_clks));
+		break;
+	}
+
+	return 0;
+}
+arch_initcall(bcm63xx_clk_init);
diff --git a/arch/mips/bcm63xx/cpu.c b/arch/mips/bcm63xx/cpu.c
new file mode 100644
index 000000000..8e3e199dd
--- /dev/null
+++ b/arch/mips/bcm63xx/cpu.c
@@ -0,0 +1,385 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ * Copyright (C) 2009 Florian Fainelli <florian@openwrt.org>
+ */
+
+#include <linux/kernel.h>
+#include <linux/export.h>
+#include <linux/cpu.h>
+#include <asm/cpu.h>
+#include <asm/cpu-info.h>
+#include <asm/mipsregs.h>
+#include <bcm63xx_cpu.h>
+#include <bcm63xx_regs.h>
+#include <bcm63xx_io.h>
+#include <bcm63xx_irq.h>
+
+const unsigned long *bcm63xx_regs_base;
+EXPORT_SYMBOL(bcm63xx_regs_base);
+
+const int *bcm63xx_irqs;
+EXPORT_SYMBOL(bcm63xx_irqs);
+
+u16 bcm63xx_cpu_id __read_mostly;
+EXPORT_SYMBOL(bcm63xx_cpu_id);
+
+static u8 bcm63xx_cpu_rev;
+static unsigned int bcm63xx_cpu_freq;
+static unsigned int bcm63xx_memory_size;
+
+static const unsigned long bcm3368_regs_base[] = {
+	__GEN_CPU_REGS_TABLE(3368)
+};
+
+static const int bcm3368_irqs[] = {
+	__GEN_CPU_IRQ_TABLE(3368)
+};
+
+static const unsigned long bcm6328_regs_base[] = {
+	__GEN_CPU_REGS_TABLE(6328)
+};
+
+static const int bcm6328_irqs[] = {
+	__GEN_CPU_IRQ_TABLE(6328)
+};
+
+static const unsigned long bcm6338_regs_base[] = {
+	__GEN_CPU_REGS_TABLE(6338)
+};
+
+static const int bcm6338_irqs[] = {
+	__GEN_CPU_IRQ_TABLE(6338)
+};
+
+static const unsigned long bcm6345_regs_base[] = {
+	__GEN_CPU_REGS_TABLE(6345)
+};
+
+static const int bcm6345_irqs[] = {
+	__GEN_CPU_IRQ_TABLE(6345)
+};
+
+static const unsigned long bcm6348_regs_base[] = {
+	__GEN_CPU_REGS_TABLE(6348)
+};
+
+static const int bcm6348_irqs[] = {
+	__GEN_CPU_IRQ_TABLE(6348)
+
+};
+
+static const unsigned long bcm6358_regs_base[] = {
+	__GEN_CPU_REGS_TABLE(6358)
+};
+
+static const int bcm6358_irqs[] = {
+	__GEN_CPU_IRQ_TABLE(6358)
+
+};
+
+static const unsigned long bcm6362_regs_base[] = {
+	__GEN_CPU_REGS_TABLE(6362)
+};
+
+static const int bcm6362_irqs[] = {
+	__GEN_CPU_IRQ_TABLE(6362)
+
+};
+
+static const unsigned long bcm6368_regs_base[] = {
+	__GEN_CPU_REGS_TABLE(6368)
+};
+
+static const int bcm6368_irqs[] = {
+	__GEN_CPU_IRQ_TABLE(6368)
+
+};
+
+u8 bcm63xx_get_cpu_rev(void)
+{
+	return bcm63xx_cpu_rev;
+}
+
+EXPORT_SYMBOL(bcm63xx_get_cpu_rev);
+
+unsigned int bcm63xx_get_cpu_freq(void)
+{
+	return bcm63xx_cpu_freq;
+}
+
+unsigned int bcm63xx_get_memory_size(void)
+{
+	return bcm63xx_memory_size;
+}
+
+static unsigned int detect_cpu_clock(void)
+{
+	u16 cpu_id = bcm63xx_get_cpu_id();
+
+	switch (cpu_id) {
+	case BCM3368_CPU_ID:
+		return 300000000;
+
+	case BCM6328_CPU_ID:
+	{
+		unsigned int tmp, mips_pll_fcvo;
+
+		tmp = bcm_misc_readl(MISC_STRAPBUS_6328_REG);
+		mips_pll_fcvo = (tmp & STRAPBUS_6328_FCVO_MASK)
+				>> STRAPBUS_6328_FCVO_SHIFT;
+
+		switch (mips_pll_fcvo) {
+		case 0x12:
+		case 0x14:
+		case 0x19:
+			return 160000000;
+		case 0x1c:
+			return 192000000;
+		case 0x13:
+		case 0x15:
+			return 200000000;
+		case 0x1a:
+			return 384000000;
+		case 0x16:
+			return 400000000;
+		default:
+			return 320000000;
+		}
+
+	}
+	case BCM6338_CPU_ID:
+		/* BCM6338 has a fixed 240 Mhz frequency */
+		return 240000000;
+
+	case BCM6345_CPU_ID:
+		/* BCM6345 has a fixed 140Mhz frequency */
+		return 140000000;
+
+	case BCM6348_CPU_ID:
+	{
+		unsigned int tmp, n1, n2, m1;
+
+		/* 16MHz * (N1 + 1) * (N2 + 2) / (M1_CPU + 1) */
+		tmp = bcm_perf_readl(PERF_MIPSPLLCTL_REG);
+		n1 = (tmp & MIPSPLLCTL_N1_MASK) >> MIPSPLLCTL_N1_SHIFT;
+		n2 = (tmp & MIPSPLLCTL_N2_MASK) >> MIPSPLLCTL_N2_SHIFT;
+		m1 = (tmp & MIPSPLLCTL_M1CPU_MASK) >> MIPSPLLCTL_M1CPU_SHIFT;
+		n1 += 1;
+		n2 += 2;
+		m1 += 1;
+		return (16 * 1000000 * n1 * n2) / m1;
+	}
+
+	case BCM6358_CPU_ID:
+	{
+		unsigned int tmp, n1, n2, m1;
+
+		/* 16MHz * N1 * N2 / M1_CPU */
+		tmp = bcm_ddr_readl(DDR_DMIPSPLLCFG_REG);
+		n1 = (tmp & DMIPSPLLCFG_N1_MASK) >> DMIPSPLLCFG_N1_SHIFT;
+		n2 = (tmp & DMIPSPLLCFG_N2_MASK) >> DMIPSPLLCFG_N2_SHIFT;
+		m1 = (tmp & DMIPSPLLCFG_M1_MASK) >> DMIPSPLLCFG_M1_SHIFT;
+		return (16 * 1000000 * n1 * n2) / m1;
+	}
+
+	case BCM6362_CPU_ID:
+	{
+		unsigned int tmp, mips_pll_fcvo;
+
+		tmp = bcm_misc_readl(MISC_STRAPBUS_6362_REG);
+		mips_pll_fcvo = (tmp & STRAPBUS_6362_FCVO_MASK)
+				>> STRAPBUS_6362_FCVO_SHIFT;
+		switch (mips_pll_fcvo) {
+		case 0x03:
+		case 0x0b:
+		case 0x13:
+		case 0x1b:
+			return 240000000;
+		case 0x04:
+		case 0x0c:
+		case 0x14:
+		case 0x1c:
+			return 160000000;
+		case 0x05:
+		case 0x0e:
+		case 0x16:
+		case 0x1e:
+		case 0x1f:
+			return 400000000;
+		case 0x06:
+			return 440000000;
+		case 0x07:
+		case 0x17:
+			return 384000000;
+		case 0x15:
+		case 0x1d:
+			return 200000000;
+		default:
+			return 320000000;
+		}
+	}
+	case BCM6368_CPU_ID:
+	{
+		unsigned int tmp, p1, p2, ndiv, m1;
+
+		/* (64MHz / P1) * P2 * NDIV / M1_CPU */
+		tmp = bcm_ddr_readl(DDR_DMIPSPLLCFG_6368_REG);
+
+		p1 = (tmp & DMIPSPLLCFG_6368_P1_MASK) >>
+			DMIPSPLLCFG_6368_P1_SHIFT;
+
+		p2 = (tmp & DMIPSPLLCFG_6368_P2_MASK) >>
+			DMIPSPLLCFG_6368_P2_SHIFT;
+
+		ndiv = (tmp & DMIPSPLLCFG_6368_NDIV_MASK) >>
+			DMIPSPLLCFG_6368_NDIV_SHIFT;
+
+		tmp = bcm_ddr_readl(DDR_DMIPSPLLDIV_6368_REG);
+		m1 = (tmp & DMIPSPLLDIV_6368_MDIV_MASK) >>
+			DMIPSPLLDIV_6368_MDIV_SHIFT;
+
+		return (((64 * 1000000) / p1) * p2 * ndiv) / m1;
+	}
+
+	default:
+		panic("Failed to detect clock for CPU with id=%04X\n", cpu_id);
+	}
+}
+
+/*
+ * attempt to detect the amount of memory installed
+ */
+static unsigned int detect_memory_size(void)
+{
+	unsigned int cols = 0, rows = 0, is_32bits = 0, banks = 0;
+	u32 val;
+
+	if (BCMCPU_IS_6328() || BCMCPU_IS_6362())
+		return bcm_ddr_readl(DDR_CSEND_REG) << 24;
+
+	if (BCMCPU_IS_6345()) {
+		val = bcm_sdram_readl(SDRAM_MBASE_REG);
+		return val * 8 * 1024 * 1024;
+	}
+
+	if (BCMCPU_IS_6338() || BCMCPU_IS_6348()) {
+		val = bcm_sdram_readl(SDRAM_CFG_REG);
+		rows = (val & SDRAM_CFG_ROW_MASK) >> SDRAM_CFG_ROW_SHIFT;
+		cols = (val & SDRAM_CFG_COL_MASK) >> SDRAM_CFG_COL_SHIFT;
+		is_32bits = (val & SDRAM_CFG_32B_MASK) ? 1 : 0;
+		banks = (val & SDRAM_CFG_BANK_MASK) ? 2 : 1;
+	}
+
+	if (BCMCPU_IS_3368() || BCMCPU_IS_6358() || BCMCPU_IS_6368()) {
+		val = bcm_memc_readl(MEMC_CFG_REG);
+		rows = (val & MEMC_CFG_ROW_MASK) >> MEMC_CFG_ROW_SHIFT;
+		cols = (val & MEMC_CFG_COL_MASK) >> MEMC_CFG_COL_SHIFT;
+		is_32bits = (val & MEMC_CFG_32B_MASK) ? 0 : 1;
+		banks = 2;
+	}
+
+	/* 0 => 11 address bits ... 2 => 13 address bits */
+	rows += 11;
+
+	/* 0 => 8 address bits ... 2 => 10 address bits */
+	cols += 8;
+
+	return 1 << (cols + rows + (is_32bits + 1) + banks);
+}
+
+void __init bcm63xx_cpu_init(void)
+{
+	unsigned int tmp;
+	unsigned int cpu = smp_processor_id();
+	u32 chipid_reg;
+
+	/* soc registers location depends on cpu type */
+	chipid_reg = 0;
+
+	switch (current_cpu_type()) {
+	case CPU_BMIPS3300:
+		if ((read_c0_prid() & PRID_IMP_MASK) != PRID_IMP_BMIPS3300_ALT)
+			__cpu_name[cpu] = "Broadcom BCM6338";
+		fallthrough;
+	case CPU_BMIPS32:
+		chipid_reg = BCM_6345_PERF_BASE;
+		break;
+	case CPU_BMIPS4350:
+		switch ((read_c0_prid() & PRID_REV_MASK)) {
+		case 0x04:
+			chipid_reg = BCM_3368_PERF_BASE;
+			break;
+		case 0x10:
+			chipid_reg = BCM_6345_PERF_BASE;
+			break;
+		default:
+			chipid_reg = BCM_6368_PERF_BASE;
+			break;
+		}
+		break;
+	}
+
+	/*
+	 * really early to panic, but delaying panic would not help since we
+	 * will never get any working console
+	 */
+	if (!chipid_reg)
+		panic("unsupported Broadcom CPU");
+
+	/* read out CPU type */
+	tmp = bcm_readl(chipid_reg);
+	bcm63xx_cpu_id = (tmp & REV_CHIPID_MASK) >> REV_CHIPID_SHIFT;
+	bcm63xx_cpu_rev = (tmp & REV_REVID_MASK) >> REV_REVID_SHIFT;
+
+	switch (bcm63xx_cpu_id) {
+	case BCM3368_CPU_ID:
+		bcm63xx_regs_base = bcm3368_regs_base;
+		bcm63xx_irqs = bcm3368_irqs;
+		break;
+	case BCM6328_CPU_ID:
+		bcm63xx_regs_base = bcm6328_regs_base;
+		bcm63xx_irqs = bcm6328_irqs;
+		break;
+	case BCM6338_CPU_ID:
+		bcm63xx_regs_base = bcm6338_regs_base;
+		bcm63xx_irqs = bcm6338_irqs;
+		break;
+	case BCM6345_CPU_ID:
+		bcm63xx_regs_base = bcm6345_regs_base;
+		bcm63xx_irqs = bcm6345_irqs;
+		break;
+	case BCM6348_CPU_ID:
+		bcm63xx_regs_base = bcm6348_regs_base;
+		bcm63xx_irqs = bcm6348_irqs;
+		break;
+	case BCM6358_CPU_ID:
+		bcm63xx_regs_base = bcm6358_regs_base;
+		bcm63xx_irqs = bcm6358_irqs;
+		break;
+	case BCM6362_CPU_ID:
+		bcm63xx_regs_base = bcm6362_regs_base;
+		bcm63xx_irqs = bcm6362_irqs;
+		break;
+	case BCM6368_CPU_ID:
+		bcm63xx_regs_base = bcm6368_regs_base;
+		bcm63xx_irqs = bcm6368_irqs;
+		break;
+	default:
+		panic("unsupported broadcom CPU %x", bcm63xx_cpu_id);
+		break;
+	}
+
+	bcm63xx_cpu_freq = detect_cpu_clock();
+	bcm63xx_memory_size = detect_memory_size();
+
+	pr_info("Detected Broadcom 0x%04x CPU revision %02x\n",
+		bcm63xx_cpu_id, bcm63xx_cpu_rev);
+	pr_info("CPU frequency is %u MHz\n",
+		bcm63xx_cpu_freq / 1000000);
+	pr_info("%uMB of RAM installed\n",
+		bcm63xx_memory_size >> 20);
+}
diff --git a/arch/mips/bcm63xx/cs.c b/arch/mips/bcm63xx/cs.c
new file mode 100644
index 000000000..29205badc
--- /dev/null
+++ b/arch/mips/bcm63xx/cs.c
@@ -0,0 +1,145 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ */
+
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/export.h>
+#include <linux/spinlock.h>
+#include <linux/log2.h>
+#include <bcm63xx_cpu.h>
+#include <bcm63xx_io.h>
+#include <bcm63xx_regs.h>
+#include <bcm63xx_cs.h>
+
+static DEFINE_SPINLOCK(bcm63xx_cs_lock);
+
+/*
+ * check if given chip select exists
+ */
+static int is_valid_cs(unsigned int cs)
+{
+	if (cs > 6)
+		return 0;
+	return 1;
+}
+
+/*
+ * Configure chipselect base address and size (bytes).
+ * Size must be a power of two between 8k and 256M.
+ */
+int bcm63xx_set_cs_base(unsigned int cs, u32 base, unsigned int size)
+{
+	unsigned long flags;
+	u32 val;
+
+	if (!is_valid_cs(cs))
+		return -EINVAL;
+
+	/* sanity check on size */
+	if (size != roundup_pow_of_two(size))
+		return -EINVAL;
+
+	if (size < 8 * 1024 || size > 256 * 1024 * 1024)
+		return -EINVAL;
+
+	val = (base & MPI_CSBASE_BASE_MASK);
+	/* 8k => 0 - 256M => 15 */
+	val |= (ilog2(size) - ilog2(8 * 1024)) << MPI_CSBASE_SIZE_SHIFT;
+
+	spin_lock_irqsave(&bcm63xx_cs_lock, flags);
+	bcm_mpi_writel(val, MPI_CSBASE_REG(cs));
+	spin_unlock_irqrestore(&bcm63xx_cs_lock, flags);
+
+	return 0;
+}
+
+EXPORT_SYMBOL(bcm63xx_set_cs_base);
+
+/*
+ * configure chipselect timing (ns)
+ */
+int bcm63xx_set_cs_timing(unsigned int cs, unsigned int wait,
+			   unsigned int setup, unsigned int hold)
+{
+	unsigned long flags;
+	u32 val;
+
+	if (!is_valid_cs(cs))
+		return -EINVAL;
+
+	spin_lock_irqsave(&bcm63xx_cs_lock, flags);
+	val = bcm_mpi_readl(MPI_CSCTL_REG(cs));
+	val &= ~(MPI_CSCTL_WAIT_MASK);
+	val &= ~(MPI_CSCTL_SETUP_MASK);
+	val &= ~(MPI_CSCTL_HOLD_MASK);
+	val |= wait << MPI_CSCTL_WAIT_SHIFT;
+	val |= setup << MPI_CSCTL_SETUP_SHIFT;
+	val |= hold << MPI_CSCTL_HOLD_SHIFT;
+	bcm_mpi_writel(val, MPI_CSCTL_REG(cs));
+	spin_unlock_irqrestore(&bcm63xx_cs_lock, flags);
+
+	return 0;
+}
+
+EXPORT_SYMBOL(bcm63xx_set_cs_timing);
+
+/*
+ * configure other chipselect parameter (data bus size, ...)
+ */
+int bcm63xx_set_cs_param(unsigned int cs, u32 params)
+{
+	unsigned long flags;
+	u32 val;
+
+	if (!is_valid_cs(cs))
+		return -EINVAL;
+
+	/* none of this fields apply to pcmcia */
+	if (cs == MPI_CS_PCMCIA_COMMON ||
+	    cs == MPI_CS_PCMCIA_ATTR ||
+	    cs == MPI_CS_PCMCIA_IO)
+		return -EINVAL;
+
+	spin_lock_irqsave(&bcm63xx_cs_lock, flags);
+	val = bcm_mpi_readl(MPI_CSCTL_REG(cs));
+	val &= ~(MPI_CSCTL_DATA16_MASK);
+	val &= ~(MPI_CSCTL_SYNCMODE_MASK);
+	val &= ~(MPI_CSCTL_TSIZE_MASK);
+	val &= ~(MPI_CSCTL_ENDIANSWAP_MASK);
+	val |= params;
+	bcm_mpi_writel(val, MPI_CSCTL_REG(cs));
+	spin_unlock_irqrestore(&bcm63xx_cs_lock, flags);
+
+	return 0;
+}
+
+EXPORT_SYMBOL(bcm63xx_set_cs_param);
+
+/*
+ * set cs status (enable/disable)
+ */
+int bcm63xx_set_cs_status(unsigned int cs, int enable)
+{
+	unsigned long flags;
+	u32 val;
+
+	if (!is_valid_cs(cs))
+		return -EINVAL;
+
+	spin_lock_irqsave(&bcm63xx_cs_lock, flags);
+	val = bcm_mpi_readl(MPI_CSCTL_REG(cs));
+	if (enable)
+		val |= MPI_CSCTL_ENABLE_MASK;
+	else
+		val &= ~MPI_CSCTL_ENABLE_MASK;
+	bcm_mpi_writel(val, MPI_CSCTL_REG(cs));
+	spin_unlock_irqrestore(&bcm63xx_cs_lock, flags);
+	return 0;
+}
+
+EXPORT_SYMBOL(bcm63xx_set_cs_status);
diff --git a/arch/mips/bcm63xx/dev-enet.c b/arch/mips/bcm63xx/dev-enet.c
new file mode 100644
index 000000000..8e73d65f3
--- /dev/null
+++ b/arch/mips/bcm63xx/dev-enet.c
@@ -0,0 +1,327 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/export.h>
+#include <bcm63xx_dev_enet.h>
+#include <bcm63xx_io.h>
+#include <bcm63xx_regs.h>
+
+static const unsigned long bcm6348_regs_enetdmac[] = {
+	[ENETDMAC_CHANCFG]	= ENETDMAC_CHANCFG_REG,
+	[ENETDMAC_IR]		= ENETDMAC_IR_REG,
+	[ENETDMAC_IRMASK]	= ENETDMAC_IRMASK_REG,
+	[ENETDMAC_MAXBURST]	= ENETDMAC_MAXBURST_REG,
+};
+
+static const unsigned long bcm6345_regs_enetdmac[] = {
+	[ENETDMAC_CHANCFG]	= ENETDMA_6345_CHANCFG_REG,
+	[ENETDMAC_IR]		= ENETDMA_6345_IR_REG,
+	[ENETDMAC_IRMASK]	= ENETDMA_6345_IRMASK_REG,
+	[ENETDMAC_MAXBURST]	= ENETDMA_6345_MAXBURST_REG,
+	[ENETDMAC_BUFALLOC]	= ENETDMA_6345_BUFALLOC_REG,
+	[ENETDMAC_RSTART]	= ENETDMA_6345_RSTART_REG,
+	[ENETDMAC_FC]		= ENETDMA_6345_FC_REG,
+	[ENETDMAC_LEN]		= ENETDMA_6345_LEN_REG,
+};
+
+const unsigned long *bcm63xx_regs_enetdmac;
+EXPORT_SYMBOL(bcm63xx_regs_enetdmac);
+
+static __init void bcm63xx_enetdmac_regs_init(void)
+{
+	if (BCMCPU_IS_6345())
+		bcm63xx_regs_enetdmac = bcm6345_regs_enetdmac;
+	else
+		bcm63xx_regs_enetdmac = bcm6348_regs_enetdmac;
+}
+
+static struct resource shared_res[] = {
+	{
+		.start		= -1, /* filled at runtime */
+		.end		= -1, /* filled at runtime */
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= -1, /* filled at runtime */
+		.end		= -1, /* filled at runtime */
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= -1, /* filled at runtime */
+		.end		= -1, /* filled at runtime */
+		.flags		= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device bcm63xx_enet_shared_device = {
+	.name		= "bcm63xx_enet_shared",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(shared_res),
+	.resource	= shared_res,
+};
+
+static int shared_device_registered;
+
+static u64 enet_dmamask = DMA_BIT_MASK(32);
+
+static struct resource enet0_res[] = {
+	{
+		.start		= -1, /* filled at runtime */
+		.end		= -1, /* filled at runtime */
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= -1, /* filled at runtime */
+		.flags		= IORESOURCE_IRQ,
+	},
+	{
+		.start		= -1, /* filled at runtime */
+		.flags		= IORESOURCE_IRQ,
+	},
+	{
+		.start		= -1, /* filled at runtime */
+		.flags		= IORESOURCE_IRQ,
+	},
+};
+
+static struct bcm63xx_enet_platform_data enet0_pd;
+
+static struct platform_device bcm63xx_enet0_device = {
+	.name		= "bcm63xx_enet",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(enet0_res),
+	.resource	= enet0_res,
+	.dev		= {
+		.platform_data = &enet0_pd,
+		.dma_mask = &enet_dmamask,
+		.coherent_dma_mask = DMA_BIT_MASK(32),
+	},
+};
+
+static struct resource enet1_res[] = {
+	{
+		.start		= -1, /* filled at runtime */
+		.end		= -1, /* filled at runtime */
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= -1, /* filled at runtime */
+		.flags		= IORESOURCE_IRQ,
+	},
+	{
+		.start		= -1, /* filled at runtime */
+		.flags		= IORESOURCE_IRQ,
+	},
+	{
+		.start		= -1, /* filled at runtime */
+		.flags		= IORESOURCE_IRQ,
+	},
+};
+
+static struct bcm63xx_enet_platform_data enet1_pd;
+
+static struct platform_device bcm63xx_enet1_device = {
+	.name		= "bcm63xx_enet",
+	.id		= 1,
+	.num_resources	= ARRAY_SIZE(enet1_res),
+	.resource	= enet1_res,
+	.dev		= {
+		.platform_data = &enet1_pd,
+		.dma_mask = &enet_dmamask,
+		.coherent_dma_mask = DMA_BIT_MASK(32),
+	},
+};
+
+static struct resource enetsw_res[] = {
+	{
+		/* start & end filled at runtime */
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		/* start filled at runtime */
+		.flags		= IORESOURCE_IRQ,
+	},
+	{
+		/* start filled at runtime */
+		.flags		= IORESOURCE_IRQ,
+	},
+};
+
+static struct bcm63xx_enetsw_platform_data enetsw_pd;
+
+static struct platform_device bcm63xx_enetsw_device = {
+	.name		= "bcm63xx_enetsw",
+	.num_resources	= ARRAY_SIZE(enetsw_res),
+	.resource	= enetsw_res,
+	.dev		= {
+		.platform_data = &enetsw_pd,
+		.dma_mask = &enet_dmamask,
+		.coherent_dma_mask = DMA_BIT_MASK(32),
+	},
+};
+
+static int __init register_shared(void)
+{
+	int ret, chan_count;
+
+	if (shared_device_registered)
+		return 0;
+
+	bcm63xx_enetdmac_regs_init();
+
+	shared_res[0].start = bcm63xx_regset_address(RSET_ENETDMA);
+	shared_res[0].end = shared_res[0].start;
+	if (BCMCPU_IS_6345())
+		shared_res[0].end += (RSET_6345_ENETDMA_SIZE) - 1;
+	else
+		shared_res[0].end += (RSET_ENETDMA_SIZE)  - 1;
+
+	if (BCMCPU_IS_6328() || BCMCPU_IS_6362() || BCMCPU_IS_6368())
+		chan_count = 32;
+	else if (BCMCPU_IS_6345())
+		chan_count = 8;
+	else
+		chan_count = 16;
+
+	shared_res[1].start = bcm63xx_regset_address(RSET_ENETDMAC);
+	shared_res[1].end = shared_res[1].start;
+	shared_res[1].end += RSET_ENETDMAC_SIZE(chan_count)  - 1;
+
+	shared_res[2].start = bcm63xx_regset_address(RSET_ENETDMAS);
+	shared_res[2].end = shared_res[2].start;
+	shared_res[2].end += RSET_ENETDMAS_SIZE(chan_count)  - 1;
+
+	ret = platform_device_register(&bcm63xx_enet_shared_device);
+	if (ret)
+		return ret;
+	shared_device_registered = 1;
+
+	return 0;
+}
+
+int __init bcm63xx_enet_register(int unit,
+				 const struct bcm63xx_enet_platform_data *pd)
+{
+	struct platform_device *pdev;
+	struct bcm63xx_enet_platform_data *dpd;
+	int ret;
+
+	if (unit > 1)
+		return -ENODEV;
+
+	if (unit == 1 && (BCMCPU_IS_6338() || BCMCPU_IS_6345()))
+		return -ENODEV;
+
+	ret = register_shared();
+	if (ret)
+		return ret;
+
+	if (unit == 0) {
+		enet0_res[0].start = bcm63xx_regset_address(RSET_ENET0);
+		enet0_res[0].end = enet0_res[0].start;
+		enet0_res[0].end += RSET_ENET_SIZE - 1;
+		enet0_res[1].start = bcm63xx_get_irq_number(IRQ_ENET0);
+		enet0_res[2].start = bcm63xx_get_irq_number(IRQ_ENET0_RXDMA);
+		enet0_res[3].start = bcm63xx_get_irq_number(IRQ_ENET0_TXDMA);
+		pdev = &bcm63xx_enet0_device;
+	} else {
+		enet1_res[0].start = bcm63xx_regset_address(RSET_ENET1);
+		enet1_res[0].end = enet1_res[0].start;
+		enet1_res[0].end += RSET_ENET_SIZE - 1;
+		enet1_res[1].start = bcm63xx_get_irq_number(IRQ_ENET1);
+		enet1_res[2].start = bcm63xx_get_irq_number(IRQ_ENET1_RXDMA);
+		enet1_res[3].start = bcm63xx_get_irq_number(IRQ_ENET1_TXDMA);
+		pdev = &bcm63xx_enet1_device;
+	}
+
+	/* copy given platform data */
+	dpd = pdev->dev.platform_data;
+	memcpy(dpd, pd, sizeof(*pd));
+
+	/* adjust them in case internal phy is used */
+	if (dpd->use_internal_phy) {
+
+		/* internal phy only exists for enet0 */
+		if (unit == 1)
+			return -ENODEV;
+
+		dpd->phy_id = 1;
+		dpd->has_phy_interrupt = 1;
+		dpd->phy_interrupt = bcm63xx_get_irq_number(IRQ_ENET_PHY);
+	}
+
+	dpd->dma_chan_en_mask = ENETDMAC_CHANCFG_EN_MASK;
+	dpd->dma_chan_int_mask = ENETDMAC_IR_PKTDONE_MASK;
+	if (BCMCPU_IS_6345()) {
+		dpd->dma_chan_en_mask |= ENETDMAC_CHANCFG_CHAINING_MASK;
+		dpd->dma_chan_en_mask |= ENETDMAC_CHANCFG_WRAP_EN_MASK;
+		dpd->dma_chan_en_mask |= ENETDMAC_CHANCFG_FLOWC_EN_MASK;
+		dpd->dma_chan_int_mask |= ENETDMA_IR_BUFDONE_MASK;
+		dpd->dma_chan_int_mask |= ENETDMA_IR_NOTOWNER_MASK;
+		dpd->dma_chan_width = ENETDMA_6345_CHAN_WIDTH;
+		dpd->dma_desc_shift = ENETDMA_6345_DESC_SHIFT;
+	} else {
+		dpd->dma_has_sram = true;
+		dpd->dma_chan_width = ENETDMA_CHAN_WIDTH;
+	}
+
+	if (unit == 0) {
+		dpd->rx_chan = 0;
+		dpd->tx_chan = 1;
+	} else {
+		dpd->rx_chan = 2;
+		dpd->tx_chan = 3;
+	}
+
+	ret = platform_device_register(pdev);
+	if (ret)
+		return ret;
+	return 0;
+}
+
+int __init
+bcm63xx_enetsw_register(const struct bcm63xx_enetsw_platform_data *pd)
+{
+	int ret;
+
+	if (!BCMCPU_IS_6328() && !BCMCPU_IS_6362() && !BCMCPU_IS_6368())
+		return -ENODEV;
+
+	ret = register_shared();
+	if (ret)
+		return ret;
+
+	enetsw_res[0].start = bcm63xx_regset_address(RSET_ENETSW);
+	enetsw_res[0].end = enetsw_res[0].start;
+	enetsw_res[0].end += RSET_ENETSW_SIZE - 1;
+	enetsw_res[1].start = bcm63xx_get_irq_number(IRQ_ENETSW_RXDMA0);
+	enetsw_res[2].start = bcm63xx_get_irq_number(IRQ_ENETSW_TXDMA0);
+	if (!enetsw_res[2].start)
+		enetsw_res[2].start = -1;
+
+	memcpy(bcm63xx_enetsw_device.dev.platform_data, pd, sizeof(*pd));
+
+	if (BCMCPU_IS_6328())
+		enetsw_pd.num_ports = ENETSW_PORTS_6328;
+	else if (BCMCPU_IS_6362() || BCMCPU_IS_6368())
+		enetsw_pd.num_ports = ENETSW_PORTS_6368;
+
+	enetsw_pd.dma_has_sram = true;
+	enetsw_pd.dma_chan_width = ENETDMA_CHAN_WIDTH;
+	enetsw_pd.dma_chan_en_mask = ENETDMAC_CHANCFG_EN_MASK;
+	enetsw_pd.dma_chan_int_mask = ENETDMAC_IR_PKTDONE_MASK;
+
+	ret = platform_device_register(&bcm63xx_enetsw_device);
+	if (ret)
+		return ret;
+
+	return 0;
+}
diff --git a/arch/mips/bcm63xx/dev-flash.c b/arch/mips/bcm63xx/dev-flash.c
new file mode 100644
index 000000000..f9cc015d3
--- /dev/null
+++ b/arch/mips/bcm63xx/dev-flash.c
@@ -0,0 +1,131 @@
+/*
+ * Broadcom BCM63xx flash registration
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ * Copyright (C) 2008 Florian Fainelli <florian@openwrt.org>
+ * Copyright (C) 2012 Jonas Gorski <jonas.gorski@gmail.com>
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+
+#include <bcm63xx_cpu.h>
+#include <bcm63xx_dev_flash.h>
+#include <bcm63xx_regs.h>
+#include <bcm63xx_io.h>
+
+static struct mtd_partition mtd_partitions[] = {
+	{
+		.name		= "cfe",
+		.offset		= 0x0,
+		.size		= 0x40000,
+	}
+};
+
+static const char *bcm63xx_part_types[] = { "bcm63xxpart", NULL };
+
+static struct physmap_flash_data flash_data = {
+	.width			= 2,
+	.parts			= mtd_partitions,
+	.part_probe_types	= bcm63xx_part_types,
+};
+
+static struct resource mtd_resources[] = {
+	{
+		.start		= 0,	/* filled at runtime */
+		.end		= 0,	/* filled at runtime */
+		.flags		= IORESOURCE_MEM,
+	}
+};
+
+static struct platform_device mtd_dev = {
+	.name			= "physmap-flash",
+	.resource		= mtd_resources,
+	.num_resources		= ARRAY_SIZE(mtd_resources),
+	.dev			= {
+		.platform_data	= &flash_data,
+	},
+};
+
+static int __init bcm63xx_detect_flash_type(void)
+{
+	u32 val;
+
+	switch (bcm63xx_get_cpu_id()) {
+	case BCM6328_CPU_ID:
+		val = bcm_misc_readl(MISC_STRAPBUS_6328_REG);
+		if (val & STRAPBUS_6328_BOOT_SEL_SERIAL)
+			return BCM63XX_FLASH_TYPE_SERIAL;
+		else
+			return BCM63XX_FLASH_TYPE_NAND;
+	case BCM6338_CPU_ID:
+	case BCM6345_CPU_ID:
+	case BCM6348_CPU_ID:
+		/* no way to auto detect so assume parallel */
+		return BCM63XX_FLASH_TYPE_PARALLEL;
+	case BCM3368_CPU_ID:
+	case BCM6358_CPU_ID:
+		val = bcm_gpio_readl(GPIO_STRAPBUS_REG);
+		if (val & STRAPBUS_6358_BOOT_SEL_PARALLEL)
+			return BCM63XX_FLASH_TYPE_PARALLEL;
+		else
+			return BCM63XX_FLASH_TYPE_SERIAL;
+	case BCM6362_CPU_ID:
+		val = bcm_misc_readl(MISC_STRAPBUS_6362_REG);
+		if (val & STRAPBUS_6362_BOOT_SEL_SERIAL)
+			return BCM63XX_FLASH_TYPE_SERIAL;
+		else
+			return BCM63XX_FLASH_TYPE_NAND;
+	case BCM6368_CPU_ID:
+		val = bcm_gpio_readl(GPIO_STRAPBUS_REG);
+		switch (val & STRAPBUS_6368_BOOT_SEL_MASK) {
+		case STRAPBUS_6368_BOOT_SEL_NAND:
+			return BCM63XX_FLASH_TYPE_NAND;
+		case STRAPBUS_6368_BOOT_SEL_SERIAL:
+			return BCM63XX_FLASH_TYPE_SERIAL;
+		case STRAPBUS_6368_BOOT_SEL_PARALLEL:
+			return BCM63XX_FLASH_TYPE_PARALLEL;
+		}
+		fallthrough;
+	default:
+		return -EINVAL;
+	}
+}
+
+int __init bcm63xx_flash_register(void)
+{
+	int flash_type;
+	u32 val;
+
+	flash_type = bcm63xx_detect_flash_type();
+
+	switch (flash_type) {
+	case BCM63XX_FLASH_TYPE_PARALLEL:
+		/* read base address of boot chip select (0) */
+		val = bcm_mpi_readl(MPI_CSBASE_REG(0));
+		val &= MPI_CSBASE_BASE_MASK;
+
+		mtd_resources[0].start = val;
+		mtd_resources[0].end = 0x1FFFFFFF;
+
+		return platform_device_register(&mtd_dev);
+	case BCM63XX_FLASH_TYPE_SERIAL:
+		pr_warn("unsupported serial flash detected\n");
+		return -ENODEV;
+	case BCM63XX_FLASH_TYPE_NAND:
+		pr_warn("unsupported NAND flash detected\n");
+		return -ENODEV;
+	default:
+		pr_err("flash detection failed for BCM%x: %d\n",
+		       bcm63xx_get_cpu_id(), flash_type);
+		return -ENODEV;
+	}
+}
diff --git a/arch/mips/bcm63xx/dev-hsspi.c b/arch/mips/bcm63xx/dev-hsspi.c
new file mode 100644
index 000000000..696abc48e
--- /dev/null
+++ b/arch/mips/bcm63xx/dev-hsspi.c
@@ -0,0 +1,47 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2012 Jonas Gorski <jonas.gorski@gmail.com>
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+
+#include <bcm63xx_cpu.h>
+#include <bcm63xx_dev_hsspi.h>
+#include <bcm63xx_regs.h>
+
+static struct resource spi_resources[] = {
+	{
+		.start		= -1, /* filled at runtime */
+		.end		= -1, /* filled at runtime */
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= -1, /* filled at runtime */
+		.flags		= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bcm63xx_hsspi_device = {
+	.name		= "bcm63xx-hsspi",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(spi_resources),
+	.resource	= spi_resources,
+};
+
+int __init bcm63xx_hsspi_register(void)
+{
+	if (!BCMCPU_IS_6328() && !BCMCPU_IS_6362())
+		return -ENODEV;
+
+	spi_resources[0].start = bcm63xx_regset_address(RSET_HSSPI);
+	spi_resources[0].end = spi_resources[0].start;
+	spi_resources[0].end += RSET_HSSPI_SIZE - 1;
+	spi_resources[1].start = bcm63xx_get_irq_number(IRQ_HSSPI);
+
+	return platform_device_register(&bcm63xx_hsspi_device);
+}
diff --git a/arch/mips/bcm63xx/dev-pcmcia.c b/arch/mips/bcm63xx/dev-pcmcia.c
new file mode 100644
index 000000000..9496cd236
--- /dev/null
+++ b/arch/mips/bcm63xx/dev-pcmcia.c
@@ -0,0 +1,144 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <asm/bootinfo.h>
+#include <linux/platform_device.h>
+#include <bcm63xx_cs.h>
+#include <bcm63xx_cpu.h>
+#include <bcm63xx_dev_pcmcia.h>
+#include <bcm63xx_io.h>
+#include <bcm63xx_regs.h>
+
+static struct resource pcmcia_resources[] = {
+	/* pcmcia registers */
+	{
+		/* start & end filled at runtime */
+		.flags		= IORESOURCE_MEM,
+	},
+
+	/* pcmcia memory zone resources */
+	{
+		.start		= BCM_PCMCIA_COMMON_BASE_PA,
+		.end		= BCM_PCMCIA_COMMON_END_PA,
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= BCM_PCMCIA_ATTR_BASE_PA,
+		.end		= BCM_PCMCIA_ATTR_END_PA,
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= BCM_PCMCIA_IO_BASE_PA,
+		.end		= BCM_PCMCIA_IO_END_PA,
+		.flags		= IORESOURCE_MEM,
+	},
+
+	/* PCMCIA irq */
+	{
+		/* start filled at runtime */
+		.flags		= IORESOURCE_IRQ,
+	},
+
+	/* declare PCMCIA IO resource also */
+	{
+		.start		= BCM_PCMCIA_IO_BASE_PA,
+		.end		= BCM_PCMCIA_IO_END_PA,
+		.flags		= IORESOURCE_IO,
+	},
+};
+
+static struct bcm63xx_pcmcia_platform_data pd;
+
+static struct platform_device bcm63xx_pcmcia_device = {
+	.name		= "bcm63xx_pcmcia",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(pcmcia_resources),
+	.resource	= pcmcia_resources,
+	.dev		= {
+		.platform_data = &pd,
+	},
+};
+
+static int __init config_pcmcia_cs(unsigned int cs,
+				   u32 base, unsigned int size)
+{
+	int ret;
+
+	ret = bcm63xx_set_cs_status(cs, 0);
+	if (!ret)
+		ret = bcm63xx_set_cs_base(cs, base, size);
+	if (!ret)
+		ret = bcm63xx_set_cs_status(cs, 1);
+	return ret;
+}
+
+static const struct {
+	unsigned int	cs;
+	unsigned int	base;
+	unsigned int	size;
+} pcmcia_cs[3] __initconst = {
+	{
+		.cs	= MPI_CS_PCMCIA_COMMON,
+		.base	= BCM_PCMCIA_COMMON_BASE_PA,
+		.size	= BCM_PCMCIA_COMMON_SIZE
+	},
+	{
+		.cs	= MPI_CS_PCMCIA_ATTR,
+		.base	= BCM_PCMCIA_ATTR_BASE_PA,
+		.size	= BCM_PCMCIA_ATTR_SIZE
+	},
+	{
+		.cs	= MPI_CS_PCMCIA_IO,
+		.base	= BCM_PCMCIA_IO_BASE_PA,
+		.size	= BCM_PCMCIA_IO_SIZE
+	},
+};
+
+int __init bcm63xx_pcmcia_register(void)
+{
+	int ret, i;
+
+	if (!BCMCPU_IS_6348() && !BCMCPU_IS_6358())
+		return 0;
+
+	/* use correct pcmcia ready gpio depending on processor */
+	switch (bcm63xx_get_cpu_id()) {
+	case BCM6348_CPU_ID:
+		pd.ready_gpio = 22;
+		break;
+
+	case BCM6358_CPU_ID:
+		pd.ready_gpio = 18;
+		break;
+
+	default:
+		return -ENODEV;
+	}
+
+	pcmcia_resources[0].start = bcm63xx_regset_address(RSET_PCMCIA);
+	pcmcia_resources[0].end = pcmcia_resources[0].start +
+		RSET_PCMCIA_SIZE - 1;
+	pcmcia_resources[4].start = bcm63xx_get_irq_number(IRQ_PCMCIA);
+
+	/* configure pcmcia chip selects */
+	for (i = 0; i < 3; i++) {
+		ret = config_pcmcia_cs(pcmcia_cs[i].cs,
+				       pcmcia_cs[i].base,
+				       pcmcia_cs[i].size);
+		if (ret)
+			goto out_err;
+	}
+
+	return platform_device_register(&bcm63xx_pcmcia_device);
+
+out_err:
+	pr_err("unable to set pcmcia chip select\n");
+	return ret;
+}
diff --git a/arch/mips/bcm63xx/dev-rng.c b/arch/mips/bcm63xx/dev-rng.c
new file mode 100644
index 000000000..d277b4dc6
--- /dev/null
+++ b/arch/mips/bcm63xx/dev-rng.c
@@ -0,0 +1,40 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2011 Florian Fainelli <florian@openwrt.org>
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <bcm63xx_cpu.h>
+
+static struct resource rng_resources[] = {
+	{
+		.start		= -1, /* filled at runtime */
+		.end		= -1, /* filled at runtime */
+		.flags		= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device bcm63xx_rng_device = {
+	.name		= "bcm63xx-rng",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(rng_resources),
+	.resource	= rng_resources,
+};
+
+int __init bcm63xx_rng_register(void)
+{
+	if (!BCMCPU_IS_6368())
+		return -ENODEV;
+
+	rng_resources[0].start = bcm63xx_regset_address(RSET_RNG);
+	rng_resources[0].end = rng_resources[0].start;
+	rng_resources[0].end += RSET_RNG_SIZE - 1;
+
+	return platform_device_register(&bcm63xx_rng_device);
+}
+arch_initcall(bcm63xx_rng_register);
diff --git a/arch/mips/bcm63xx/dev-spi.c b/arch/mips/bcm63xx/dev-spi.c
new file mode 100644
index 000000000..232385441
--- /dev/null
+++ b/arch/mips/bcm63xx/dev-spi.c
@@ -0,0 +1,60 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2009-2011 Florian Fainelli <florian@openwrt.org>
+ * Copyright (C) 2010 Tanguy Bouzeloc <tanguy.bouzeloc@efixo.com>
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/export.h>
+#include <linux/platform_device.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+
+#include <bcm63xx_cpu.h>
+#include <bcm63xx_dev_spi.h>
+#include <bcm63xx_regs.h>
+
+static struct resource spi_resources[] = {
+	{
+		.start		= -1, /* filled at runtime */
+		.end		= -1, /* filled at runtime */
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		.start		= -1, /* filled at runtime */
+		.flags		= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bcm63xx_spi_device = {
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(spi_resources),
+	.resource	= spi_resources,
+};
+
+int __init bcm63xx_spi_register(void)
+{
+	if (BCMCPU_IS_6328() || BCMCPU_IS_6345())
+		return -ENODEV;
+
+	spi_resources[0].start = bcm63xx_regset_address(RSET_SPI);
+	spi_resources[0].end = spi_resources[0].start;
+	spi_resources[1].start = bcm63xx_get_irq_number(IRQ_SPI);
+
+	if (BCMCPU_IS_6338() || BCMCPU_IS_6348()) {
+		bcm63xx_spi_device.name = "bcm6348-spi",
+		spi_resources[0].end += BCM_6348_RSET_SPI_SIZE - 1;
+	}
+
+	if (BCMCPU_IS_3368() || BCMCPU_IS_6358() || BCMCPU_IS_6362() ||
+		BCMCPU_IS_6368()) {
+		bcm63xx_spi_device.name = "bcm6358-spi",
+		spi_resources[0].end += BCM_6358_RSET_SPI_SIZE - 1;
+	}
+
+	return platform_device_register(&bcm63xx_spi_device);
+}
diff --git a/arch/mips/bcm63xx/dev-uart.c b/arch/mips/bcm63xx/dev-uart.c
new file mode 100644
index 000000000..3bc7f3bfc
--- /dev/null
+++ b/arch/mips/bcm63xx/dev-uart.c
@@ -0,0 +1,76 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <bcm63xx_cpu.h>
+
+static struct resource uart0_resources[] = {
+	{
+		/* start & end filled at runtime */
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		/* start filled at runtime */
+		.flags		= IORESOURCE_IRQ,
+	},
+};
+
+static struct resource uart1_resources[] = {
+	{
+		/* start & end filled at runtime */
+		.flags		= IORESOURCE_MEM,
+	},
+	{
+		/* start filled at runtime */
+		.flags		= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device bcm63xx_uart_devices[] = {
+	{
+		.name		= "bcm63xx_uart",
+		.id		= 0,
+		.num_resources	= ARRAY_SIZE(uart0_resources),
+		.resource	= uart0_resources,
+	},
+
+	{
+		.name		= "bcm63xx_uart",
+		.id		= 1,
+		.num_resources	= ARRAY_SIZE(uart1_resources),
+		.resource	= uart1_resources,
+	}
+};
+
+int __init bcm63xx_uart_register(unsigned int id)
+{
+	if (id >= ARRAY_SIZE(bcm63xx_uart_devices))
+		return -ENODEV;
+
+	if (id == 1 && (!BCMCPU_IS_3368() && !BCMCPU_IS_6358() &&
+		!BCMCPU_IS_6368()))
+		return -ENODEV;
+
+	if (id == 0) {
+		uart0_resources[0].start = bcm63xx_regset_address(RSET_UART0);
+		uart0_resources[0].end = uart0_resources[0].start +
+			RSET_UART_SIZE - 1;
+		uart0_resources[1].start = bcm63xx_get_irq_number(IRQ_UART0);
+	}
+
+	if (id == 1) {
+		uart1_resources[0].start = bcm63xx_regset_address(RSET_UART1);
+		uart1_resources[0].end = uart1_resources[0].start +
+			RSET_UART_SIZE - 1;
+		uart1_resources[1].start = bcm63xx_get_irq_number(IRQ_UART1);
+	}
+
+	return platform_device_register(&bcm63xx_uart_devices[id]);
+}
diff --git a/arch/mips/bcm63xx/dev-usb-usbd.c b/arch/mips/bcm63xx/dev-usb-usbd.c
new file mode 100644
index 000000000..508bd9d8d
--- /dev/null
+++ b/arch/mips/bcm63xx/dev-usb-usbd.c
@@ -0,0 +1,65 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ * Copyright (C) 2012 Kevin Cernekee <cernekee@gmail.com>
+ * Copyright (C) 2012 Broadcom Corporation
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
+#include <bcm63xx_cpu.h>
+#include <bcm63xx_dev_usb_usbd.h>
+
+#define NUM_MMIO		2
+#define NUM_IRQ			7
+
+static struct resource usbd_resources[NUM_MMIO + NUM_IRQ];
+
+static u64 usbd_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device bcm63xx_usbd_device = {
+	.name		= "bcm63xx_udc",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(usbd_resources),
+	.resource	= usbd_resources,
+	.dev		= {
+		.dma_mask		= &usbd_dmamask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+};
+
+int __init bcm63xx_usbd_register(const struct bcm63xx_usbd_platform_data *pd)
+{
+	const int irq_list[NUM_IRQ] = { IRQ_USBD,
+		IRQ_USBD_RXDMA0, IRQ_USBD_TXDMA0,
+		IRQ_USBD_RXDMA1, IRQ_USBD_TXDMA1,
+		IRQ_USBD_RXDMA2, IRQ_USBD_TXDMA2 };
+	int i;
+
+	if (!BCMCPU_IS_6328() && !BCMCPU_IS_6368())
+		return 0;
+
+	usbd_resources[0].start = bcm63xx_regset_address(RSET_USBD);
+	usbd_resources[0].end = usbd_resources[0].start + RSET_USBD_SIZE - 1;
+	usbd_resources[0].flags = IORESOURCE_MEM;
+
+	usbd_resources[1].start = bcm63xx_regset_address(RSET_USBDMA);
+	usbd_resources[1].end = usbd_resources[1].start + RSET_USBDMA_SIZE - 1;
+	usbd_resources[1].flags = IORESOURCE_MEM;
+
+	for (i = 0; i < NUM_IRQ; i++) {
+		struct resource *r = &usbd_resources[NUM_MMIO + i];
+
+		r->start = r->end = bcm63xx_get_irq_number(irq_list[i]);
+		r->flags = IORESOURCE_IRQ;
+	}
+
+	platform_device_add_data(&bcm63xx_usbd_device, pd, sizeof(*pd));
+
+	return platform_device_register(&bcm63xx_usbd_device);
+}
diff --git a/arch/mips/bcm63xx/dev-wdt.c b/arch/mips/bcm63xx/dev-wdt.c
new file mode 100644
index 000000000..42130914a
--- /dev/null
+++ b/arch/mips/bcm63xx/dev-wdt.c
@@ -0,0 +1,45 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Florian Fainelli <florian@openwrt.org>
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/platform_data/bcm7038_wdt.h>
+#include <bcm63xx_cpu.h>
+
+static struct resource wdt_resources[] = {
+	{
+		.start		= -1, /* filled at runtime */
+		.end		= -1, /* filled at runtime */
+		.flags		= IORESOURCE_MEM,
+	},
+};
+
+static struct bcm7038_wdt_platform_data bcm63xx_wdt_pdata = {
+	.clk_name	= "periph",
+};
+
+static struct platform_device bcm63xx_wdt_device = {
+	.name		= "bcm63xx-wdt",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(wdt_resources),
+	.resource	= wdt_resources,
+	.dev		= {
+		.platform_data = &bcm63xx_wdt_pdata,
+	},
+};
+
+int __init bcm63xx_wdt_register(void)
+{
+	wdt_resources[0].start = bcm63xx_regset_address(RSET_WDT);
+	wdt_resources[0].end = wdt_resources[0].start;
+	wdt_resources[0].end += RSET_WDT_SIZE - 1;
+
+	return platform_device_register(&bcm63xx_wdt_device);
+}
+arch_initcall(bcm63xx_wdt_register);
diff --git a/arch/mips/bcm63xx/early_printk.c b/arch/mips/bcm63xx/early_printk.c
new file mode 100644
index 000000000..9e9ec27c2
--- /dev/null
+++ b/arch/mips/bcm63xx/early_printk.c
@@ -0,0 +1,30 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ */
+
+#include <bcm63xx_io.h>
+#include <linux/serial_bcm63xx.h>
+#include <asm/setup.h>
+
+static void wait_xfered(void)
+{
+	unsigned int val;
+
+	/* wait for any previous char to be transmitted */
+	do {
+		val = bcm_uart0_readl(UART_IR_REG);
+		if (val & UART_IR_STAT(UART_IR_TXEMPTY))
+			break;
+	} while (1);
+}
+
+void prom_putchar(char c)
+{
+	wait_xfered();
+	bcm_uart0_writel(c, UART_FIFO_REG);
+	wait_xfered();
+}
diff --git a/arch/mips/bcm63xx/gpio.c b/arch/mips/bcm63xx/gpio.c
new file mode 100644
index 000000000..5c4a233db
--- /dev/null
+++ b/arch/mips/bcm63xx/gpio.c
@@ -0,0 +1,148 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ * Copyright (C) 2008-2011 Florian Fainelli <florian@openwrt.org>
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/spinlock.h>
+#include <linux/platform_device.h>
+#include <linux/gpio/driver.h>
+
+#include <bcm63xx_cpu.h>
+#include <bcm63xx_gpio.h>
+#include <bcm63xx_io.h>
+#include <bcm63xx_regs.h>
+
+static u32 gpio_out_low_reg;
+
+static void bcm63xx_gpio_out_low_reg_init(void)
+{
+	switch (bcm63xx_get_cpu_id()) {
+	case BCM6345_CPU_ID:
+		gpio_out_low_reg = GPIO_DATA_LO_REG_6345;
+		break;
+	default:
+		gpio_out_low_reg = GPIO_DATA_LO_REG;
+		break;
+	}
+}
+
+static DEFINE_SPINLOCK(bcm63xx_gpio_lock);
+static u32 gpio_out_low, gpio_out_high;
+
+static void bcm63xx_gpio_set(struct gpio_chip *chip,
+			     unsigned gpio, int val)
+{
+	u32 reg;
+	u32 mask;
+	u32 *v;
+	unsigned long flags;
+
+	BUG_ON(gpio >= chip->ngpio);
+
+	if (gpio < 32) {
+		reg = gpio_out_low_reg;
+		mask = 1 << gpio;
+		v = &gpio_out_low;
+	} else {
+		reg = GPIO_DATA_HI_REG;
+		mask = 1 << (gpio - 32);
+		v = &gpio_out_high;
+	}
+
+	spin_lock_irqsave(&bcm63xx_gpio_lock, flags);
+	if (val)
+		*v |= mask;
+	else
+		*v &= ~mask;
+	bcm_gpio_writel(*v, reg);
+	spin_unlock_irqrestore(&bcm63xx_gpio_lock, flags);
+}
+
+static int bcm63xx_gpio_get(struct gpio_chip *chip, unsigned gpio)
+{
+	u32 reg;
+	u32 mask;
+
+	BUG_ON(gpio >= chip->ngpio);
+
+	if (gpio < 32) {
+		reg = gpio_out_low_reg;
+		mask = 1 << gpio;
+	} else {
+		reg = GPIO_DATA_HI_REG;
+		mask = 1 << (gpio - 32);
+	}
+
+	return !!(bcm_gpio_readl(reg) & mask);
+}
+
+static int bcm63xx_gpio_set_direction(struct gpio_chip *chip,
+				      unsigned gpio, int dir)
+{
+	u32 reg;
+	u32 mask;
+	u32 tmp;
+	unsigned long flags;
+
+	BUG_ON(gpio >= chip->ngpio);
+
+	if (gpio < 32) {
+		reg = GPIO_CTL_LO_REG;
+		mask = 1 << gpio;
+	} else {
+		reg = GPIO_CTL_HI_REG;
+		mask = 1 << (gpio - 32);
+	}
+
+	spin_lock_irqsave(&bcm63xx_gpio_lock, flags);
+	tmp = bcm_gpio_readl(reg);
+	if (dir == BCM63XX_GPIO_DIR_IN)
+		tmp &= ~mask;
+	else
+		tmp |= mask;
+	bcm_gpio_writel(tmp, reg);
+	spin_unlock_irqrestore(&bcm63xx_gpio_lock, flags);
+
+	return 0;
+}
+
+static int bcm63xx_gpio_direction_input(struct gpio_chip *chip, unsigned gpio)
+{
+	return bcm63xx_gpio_set_direction(chip, gpio, BCM63XX_GPIO_DIR_IN);
+}
+
+static int bcm63xx_gpio_direction_output(struct gpio_chip *chip,
+					 unsigned gpio, int value)
+{
+	bcm63xx_gpio_set(chip, gpio, value);
+	return bcm63xx_gpio_set_direction(chip, gpio, BCM63XX_GPIO_DIR_OUT);
+}
+
+
+static struct gpio_chip bcm63xx_gpio_chip = {
+	.label			= "bcm63xx-gpio",
+	.direction_input	= bcm63xx_gpio_direction_input,
+	.direction_output	= bcm63xx_gpio_direction_output,
+	.get			= bcm63xx_gpio_get,
+	.set			= bcm63xx_gpio_set,
+	.base			= 0,
+};
+
+int __init bcm63xx_gpio_init(void)
+{
+	bcm63xx_gpio_out_low_reg_init();
+
+	gpio_out_low = bcm_gpio_readl(gpio_out_low_reg);
+	if (!BCMCPU_IS_6345())
+		gpio_out_high = bcm_gpio_readl(GPIO_DATA_HI_REG);
+	bcm63xx_gpio_chip.ngpio = bcm63xx_gpio_count();
+	pr_info("registering %d GPIOs\n", bcm63xx_gpio_chip.ngpio);
+
+	return gpiochip_add_data(&bcm63xx_gpio_chip, NULL);
+}
diff --git a/arch/mips/bcm63xx/irq.c b/arch/mips/bcm63xx/irq.c
new file mode 100644
index 000000000..254801344
--- /dev/null
+++ b/arch/mips/bcm63xx/irq.c
@@ -0,0 +1,553 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ * Copyright (C) 2008 Nicolas Schichan <nschichan@freebox.fr>
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/spinlock.h>
+#include <asm/irq_cpu.h>
+#include <asm/mipsregs.h>
+#include <bcm63xx_cpu.h>
+#include <bcm63xx_regs.h>
+#include <bcm63xx_io.h>
+#include <bcm63xx_irq.h>
+
+
+static DEFINE_SPINLOCK(ipic_lock);
+static DEFINE_SPINLOCK(epic_lock);
+
+static u32 irq_stat_addr[2];
+static u32 irq_mask_addr[2];
+static void (*dispatch_internal)(int cpu);
+static int is_ext_irq_cascaded;
+static unsigned int ext_irq_count;
+static unsigned int ext_irq_start, ext_irq_end;
+static unsigned int ext_irq_cfg_reg1, ext_irq_cfg_reg2;
+static void (*internal_irq_mask)(struct irq_data *d);
+static void (*internal_irq_unmask)(struct irq_data *d, const struct cpumask *m);
+
+
+static inline u32 get_ext_irq_perf_reg(int irq)
+{
+	if (irq < 4)
+		return ext_irq_cfg_reg1;
+	return ext_irq_cfg_reg2;
+}
+
+static inline void handle_internal(int intbit)
+{
+	if (is_ext_irq_cascaded &&
+	    intbit >= ext_irq_start && intbit <= ext_irq_end)
+		do_IRQ(intbit - ext_irq_start + IRQ_EXTERNAL_BASE);
+	else
+		do_IRQ(intbit + IRQ_INTERNAL_BASE);
+}
+
+static inline int enable_irq_for_cpu(int cpu, struct irq_data *d,
+				     const struct cpumask *m)
+{
+	bool enable = cpu_online(cpu);
+
+#ifdef CONFIG_SMP
+	if (m)
+		enable &= cpumask_test_cpu(cpu, m);
+	else if (irqd_affinity_was_set(d))
+		enable &= cpumask_test_cpu(cpu, irq_data_get_affinity_mask(d));
+#endif
+	return enable;
+}
+
+/*
+ * dispatch internal devices IRQ (uart, enet, watchdog, ...). do not
+ * prioritize any interrupt relatively to another. the static counter
+ * will resume the loop where it ended the last time we left this
+ * function.
+ */
+
+#define BUILD_IPIC_INTERNAL(width)					\
+void __dispatch_internal_##width(int cpu)				\
+{									\
+	u32 pending[width / 32];					\
+	unsigned int src, tgt;						\
+	bool irqs_pending = false;					\
+	static unsigned int i[2];					\
+	unsigned int *next = &i[cpu];					\
+	unsigned long flags;						\
+									\
+	/* read registers in reverse order */				\
+	spin_lock_irqsave(&ipic_lock, flags);				\
+	for (src = 0, tgt = (width / 32); src < (width / 32); src++) {	\
+		u32 val;						\
+									\
+		val = bcm_readl(irq_stat_addr[cpu] + src * sizeof(u32)); \
+		val &= bcm_readl(irq_mask_addr[cpu] + src * sizeof(u32)); \
+		pending[--tgt] = val;					\
+									\
+		if (val)						\
+			irqs_pending = true;				\
+	}								\
+	spin_unlock_irqrestore(&ipic_lock, flags);			\
+									\
+	if (!irqs_pending)						\
+		return;							\
+									\
+	while (1) {							\
+		unsigned int to_call = *next;				\
+									\
+		*next = (*next + 1) & (width - 1);			\
+		if (pending[to_call / 32] & (1 << (to_call & 0x1f))) {	\
+			handle_internal(to_call);			\
+			break;						\
+		}							\
+	}								\
+}									\
+									\
+static void __internal_irq_mask_##width(struct irq_data *d)		\
+{									\
+	u32 val;							\
+	unsigned irq = d->irq - IRQ_INTERNAL_BASE;			\
+	unsigned reg = (irq / 32) ^ (width/32 - 1);			\
+	unsigned bit = irq & 0x1f;					\
+	unsigned long flags;						\
+	int cpu;							\
+									\
+	spin_lock_irqsave(&ipic_lock, flags);				\
+	for_each_present_cpu(cpu) {					\
+		if (!irq_mask_addr[cpu])				\
+			break;						\
+									\
+		val = bcm_readl(irq_mask_addr[cpu] + reg * sizeof(u32));\
+		val &= ~(1 << bit);					\
+		bcm_writel(val, irq_mask_addr[cpu] + reg * sizeof(u32));\
+	}								\
+	spin_unlock_irqrestore(&ipic_lock, flags);			\
+}									\
+									\
+static void __internal_irq_unmask_##width(struct irq_data *d,		\
+					  const struct cpumask *m)	\
+{									\
+	u32 val;							\
+	unsigned irq = d->irq - IRQ_INTERNAL_BASE;			\
+	unsigned reg = (irq / 32) ^ (width/32 - 1);			\
+	unsigned bit = irq & 0x1f;					\
+	unsigned long flags;						\
+	int cpu;							\
+									\
+	spin_lock_irqsave(&ipic_lock, flags);				\
+	for_each_present_cpu(cpu) {					\
+		if (!irq_mask_addr[cpu])				\
+			break;						\
+									\
+		val = bcm_readl(irq_mask_addr[cpu] + reg * sizeof(u32));\
+		if (enable_irq_for_cpu(cpu, d, m))			\
+			val |= (1 << bit);				\
+		else							\
+			val &= ~(1 << bit);				\
+		bcm_writel(val, irq_mask_addr[cpu] + reg * sizeof(u32));\
+	}								\
+	spin_unlock_irqrestore(&ipic_lock, flags);			\
+}
+
+BUILD_IPIC_INTERNAL(32);
+BUILD_IPIC_INTERNAL(64);
+
+asmlinkage void plat_irq_dispatch(void)
+{
+	u32 cause;
+
+	do {
+		cause = read_c0_cause() & read_c0_status() & ST0_IM;
+
+		if (!cause)
+			break;
+
+		if (cause & CAUSEF_IP7)
+			do_IRQ(7);
+		if (cause & CAUSEF_IP0)
+			do_IRQ(0);
+		if (cause & CAUSEF_IP1)
+			do_IRQ(1);
+		if (cause & CAUSEF_IP2)
+			dispatch_internal(0);
+		if (is_ext_irq_cascaded) {
+			if (cause & CAUSEF_IP3)
+				dispatch_internal(1);
+		} else {
+			if (cause & CAUSEF_IP3)
+				do_IRQ(IRQ_EXT_0);
+			if (cause & CAUSEF_IP4)
+				do_IRQ(IRQ_EXT_1);
+			if (cause & CAUSEF_IP5)
+				do_IRQ(IRQ_EXT_2);
+			if (cause & CAUSEF_IP6)
+				do_IRQ(IRQ_EXT_3);
+		}
+	} while (1);
+}
+
+/*
+ * internal IRQs operations: only mask/unmask on PERF irq mask
+ * register.
+ */
+static void bcm63xx_internal_irq_mask(struct irq_data *d)
+{
+	internal_irq_mask(d);
+}
+
+static void bcm63xx_internal_irq_unmask(struct irq_data *d)
+{
+	internal_irq_unmask(d, NULL);
+}
+
+/*
+ * external IRQs operations: mask/unmask and clear on PERF external
+ * irq control register.
+ */
+static void bcm63xx_external_irq_mask(struct irq_data *d)
+{
+	unsigned int irq = d->irq - IRQ_EXTERNAL_BASE;
+	u32 reg, regaddr;
+	unsigned long flags;
+
+	regaddr = get_ext_irq_perf_reg(irq);
+	spin_lock_irqsave(&epic_lock, flags);
+	reg = bcm_perf_readl(regaddr);
+
+	if (BCMCPU_IS_6348())
+		reg &= ~EXTIRQ_CFG_MASK_6348(irq % 4);
+	else
+		reg &= ~EXTIRQ_CFG_MASK(irq % 4);
+
+	bcm_perf_writel(reg, regaddr);
+	spin_unlock_irqrestore(&epic_lock, flags);
+
+	if (is_ext_irq_cascaded)
+		internal_irq_mask(irq_get_irq_data(irq + ext_irq_start));
+}
+
+static void bcm63xx_external_irq_unmask(struct irq_data *d)
+{
+	unsigned int irq = d->irq - IRQ_EXTERNAL_BASE;
+	u32 reg, regaddr;
+	unsigned long flags;
+
+	regaddr = get_ext_irq_perf_reg(irq);
+	spin_lock_irqsave(&epic_lock, flags);
+	reg = bcm_perf_readl(regaddr);
+
+	if (BCMCPU_IS_6348())
+		reg |= EXTIRQ_CFG_MASK_6348(irq % 4);
+	else
+		reg |= EXTIRQ_CFG_MASK(irq % 4);
+
+	bcm_perf_writel(reg, regaddr);
+	spin_unlock_irqrestore(&epic_lock, flags);
+
+	if (is_ext_irq_cascaded)
+		internal_irq_unmask(irq_get_irq_data(irq + ext_irq_start),
+				    NULL);
+}
+
+static void bcm63xx_external_irq_clear(struct irq_data *d)
+{
+	unsigned int irq = d->irq - IRQ_EXTERNAL_BASE;
+	u32 reg, regaddr;
+	unsigned long flags;
+
+	regaddr = get_ext_irq_perf_reg(irq);
+	spin_lock_irqsave(&epic_lock, flags);
+	reg = bcm_perf_readl(regaddr);
+
+	if (BCMCPU_IS_6348())
+		reg |= EXTIRQ_CFG_CLEAR_6348(irq % 4);
+	else
+		reg |= EXTIRQ_CFG_CLEAR(irq % 4);
+
+	bcm_perf_writel(reg, regaddr);
+	spin_unlock_irqrestore(&epic_lock, flags);
+}
+
+static int bcm63xx_external_irq_set_type(struct irq_data *d,
+					 unsigned int flow_type)
+{
+	unsigned int irq = d->irq - IRQ_EXTERNAL_BASE;
+	u32 reg, regaddr;
+	int levelsense, sense, bothedge;
+	unsigned long flags;
+
+	flow_type &= IRQ_TYPE_SENSE_MASK;
+
+	if (flow_type == IRQ_TYPE_NONE)
+		flow_type = IRQ_TYPE_LEVEL_LOW;
+
+	levelsense = sense = bothedge = 0;
+	switch (flow_type) {
+	case IRQ_TYPE_EDGE_BOTH:
+		bothedge = 1;
+		break;
+
+	case IRQ_TYPE_EDGE_RISING:
+		sense = 1;
+		break;
+
+	case IRQ_TYPE_EDGE_FALLING:
+		break;
+
+	case IRQ_TYPE_LEVEL_HIGH:
+		levelsense = 1;
+		sense = 1;
+		break;
+
+	case IRQ_TYPE_LEVEL_LOW:
+		levelsense = 1;
+		break;
+
+	default:
+		pr_err("bogus flow type combination given !\n");
+		return -EINVAL;
+	}
+
+	regaddr = get_ext_irq_perf_reg(irq);
+	spin_lock_irqsave(&epic_lock, flags);
+	reg = bcm_perf_readl(regaddr);
+	irq %= 4;
+
+	switch (bcm63xx_get_cpu_id()) {
+	case BCM6348_CPU_ID:
+		if (levelsense)
+			reg |= EXTIRQ_CFG_LEVELSENSE_6348(irq);
+		else
+			reg &= ~EXTIRQ_CFG_LEVELSENSE_6348(irq);
+		if (sense)
+			reg |= EXTIRQ_CFG_SENSE_6348(irq);
+		else
+			reg &= ~EXTIRQ_CFG_SENSE_6348(irq);
+		if (bothedge)
+			reg |= EXTIRQ_CFG_BOTHEDGE_6348(irq);
+		else
+			reg &= ~EXTIRQ_CFG_BOTHEDGE_6348(irq);
+		break;
+
+	case BCM3368_CPU_ID:
+	case BCM6328_CPU_ID:
+	case BCM6338_CPU_ID:
+	case BCM6345_CPU_ID:
+	case BCM6358_CPU_ID:
+	case BCM6362_CPU_ID:
+	case BCM6368_CPU_ID:
+		if (levelsense)
+			reg |= EXTIRQ_CFG_LEVELSENSE(irq);
+		else
+			reg &= ~EXTIRQ_CFG_LEVELSENSE(irq);
+		if (sense)
+			reg |= EXTIRQ_CFG_SENSE(irq);
+		else
+			reg &= ~EXTIRQ_CFG_SENSE(irq);
+		if (bothedge)
+			reg |= EXTIRQ_CFG_BOTHEDGE(irq);
+		else
+			reg &= ~EXTIRQ_CFG_BOTHEDGE(irq);
+		break;
+	default:
+		BUG();
+	}
+
+	bcm_perf_writel(reg, regaddr);
+	spin_unlock_irqrestore(&epic_lock, flags);
+
+	irqd_set_trigger_type(d, flow_type);
+	if (flow_type & (IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_LEVEL_HIGH))
+		irq_set_handler_locked(d, handle_level_irq);
+	else
+		irq_set_handler_locked(d, handle_edge_irq);
+
+	return IRQ_SET_MASK_OK_NOCOPY;
+}
+
+#ifdef CONFIG_SMP
+static int bcm63xx_internal_set_affinity(struct irq_data *data,
+					 const struct cpumask *dest,
+					 bool force)
+{
+	if (!irqd_irq_disabled(data))
+		internal_irq_unmask(data, dest);
+
+	return 0;
+}
+#endif
+
+static struct irq_chip bcm63xx_internal_irq_chip = {
+	.name		= "bcm63xx_ipic",
+	.irq_mask	= bcm63xx_internal_irq_mask,
+	.irq_unmask	= bcm63xx_internal_irq_unmask,
+};
+
+static struct irq_chip bcm63xx_external_irq_chip = {
+	.name		= "bcm63xx_epic",
+	.irq_ack	= bcm63xx_external_irq_clear,
+
+	.irq_mask	= bcm63xx_external_irq_mask,
+	.irq_unmask	= bcm63xx_external_irq_unmask,
+
+	.irq_set_type	= bcm63xx_external_irq_set_type,
+};
+
+static void bcm63xx_init_irq(void)
+{
+	int irq_bits;
+
+	irq_stat_addr[0] = bcm63xx_regset_address(RSET_PERF);
+	irq_mask_addr[0] = bcm63xx_regset_address(RSET_PERF);
+	irq_stat_addr[1] = bcm63xx_regset_address(RSET_PERF);
+	irq_mask_addr[1] = bcm63xx_regset_address(RSET_PERF);
+
+	switch (bcm63xx_get_cpu_id()) {
+	case BCM3368_CPU_ID:
+		irq_stat_addr[0] += PERF_IRQSTAT_3368_REG;
+		irq_mask_addr[0] += PERF_IRQMASK_3368_REG;
+		irq_stat_addr[1] = 0;
+		irq_mask_addr[1] = 0;
+		irq_bits = 32;
+		ext_irq_count = 4;
+		ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_3368;
+		break;
+	case BCM6328_CPU_ID:
+		irq_stat_addr[0] += PERF_IRQSTAT_6328_REG(0);
+		irq_mask_addr[0] += PERF_IRQMASK_6328_REG(0);
+		irq_stat_addr[1] += PERF_IRQSTAT_6328_REG(1);
+		irq_mask_addr[1] += PERF_IRQMASK_6328_REG(1);
+		irq_bits = 64;
+		ext_irq_count = 4;
+		is_ext_irq_cascaded = 1;
+		ext_irq_start = BCM_6328_EXT_IRQ0 - IRQ_INTERNAL_BASE;
+		ext_irq_end = BCM_6328_EXT_IRQ3 - IRQ_INTERNAL_BASE;
+		ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6328;
+		break;
+	case BCM6338_CPU_ID:
+		irq_stat_addr[0] += PERF_IRQSTAT_6338_REG;
+		irq_mask_addr[0] += PERF_IRQMASK_6338_REG;
+		irq_stat_addr[1] = 0;
+		irq_mask_addr[1] = 0;
+		irq_bits = 32;
+		ext_irq_count = 4;
+		ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6338;
+		break;
+	case BCM6345_CPU_ID:
+		irq_stat_addr[0] += PERF_IRQSTAT_6345_REG;
+		irq_mask_addr[0] += PERF_IRQMASK_6345_REG;
+		irq_stat_addr[1] = 0;
+		irq_mask_addr[1] = 0;
+		irq_bits = 32;
+		ext_irq_count = 4;
+		ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6345;
+		break;
+	case BCM6348_CPU_ID:
+		irq_stat_addr[0] += PERF_IRQSTAT_6348_REG;
+		irq_mask_addr[0] += PERF_IRQMASK_6348_REG;
+		irq_stat_addr[1] = 0;
+		irq_mask_addr[1] = 0;
+		irq_bits = 32;
+		ext_irq_count = 4;
+		ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6348;
+		break;
+	case BCM6358_CPU_ID:
+		irq_stat_addr[0] += PERF_IRQSTAT_6358_REG(0);
+		irq_mask_addr[0] += PERF_IRQMASK_6358_REG(0);
+		irq_stat_addr[1] += PERF_IRQSTAT_6358_REG(1);
+		irq_mask_addr[1] += PERF_IRQMASK_6358_REG(1);
+		irq_bits = 32;
+		ext_irq_count = 4;
+		is_ext_irq_cascaded = 1;
+		ext_irq_start = BCM_6358_EXT_IRQ0 - IRQ_INTERNAL_BASE;
+		ext_irq_end = BCM_6358_EXT_IRQ3 - IRQ_INTERNAL_BASE;
+		ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6358;
+		break;
+	case BCM6362_CPU_ID:
+		irq_stat_addr[0] += PERF_IRQSTAT_6362_REG(0);
+		irq_mask_addr[0] += PERF_IRQMASK_6362_REG(0);
+		irq_stat_addr[1] += PERF_IRQSTAT_6362_REG(1);
+		irq_mask_addr[1] += PERF_IRQMASK_6362_REG(1);
+		irq_bits = 64;
+		ext_irq_count = 4;
+		is_ext_irq_cascaded = 1;
+		ext_irq_start = BCM_6362_EXT_IRQ0 - IRQ_INTERNAL_BASE;
+		ext_irq_end = BCM_6362_EXT_IRQ3 - IRQ_INTERNAL_BASE;
+		ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6362;
+		break;
+	case BCM6368_CPU_ID:
+		irq_stat_addr[0] += PERF_IRQSTAT_6368_REG(0);
+		irq_mask_addr[0] += PERF_IRQMASK_6368_REG(0);
+		irq_stat_addr[1] += PERF_IRQSTAT_6368_REG(1);
+		irq_mask_addr[1] += PERF_IRQMASK_6368_REG(1);
+		irq_bits = 64;
+		ext_irq_count = 6;
+		is_ext_irq_cascaded = 1;
+		ext_irq_start = BCM_6368_EXT_IRQ0 - IRQ_INTERNAL_BASE;
+		ext_irq_end = BCM_6368_EXT_IRQ5 - IRQ_INTERNAL_BASE;
+		ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6368;
+		ext_irq_cfg_reg2 = PERF_EXTIRQ_CFG_REG2_6368;
+		break;
+	default:
+		BUG();
+	}
+
+	if (irq_bits == 32) {
+		dispatch_internal = __dispatch_internal_32;
+		internal_irq_mask = __internal_irq_mask_32;
+		internal_irq_unmask = __internal_irq_unmask_32;
+	} else {
+		dispatch_internal = __dispatch_internal_64;
+		internal_irq_mask = __internal_irq_mask_64;
+		internal_irq_unmask = __internal_irq_unmask_64;
+	}
+}
+
+void __init arch_init_irq(void)
+{
+	int i, irq;
+
+	bcm63xx_init_irq();
+	mips_cpu_irq_init();
+	for (i = IRQ_INTERNAL_BASE; i < NR_IRQS; ++i)
+		irq_set_chip_and_handler(i, &bcm63xx_internal_irq_chip,
+					 handle_level_irq);
+
+	for (i = IRQ_EXTERNAL_BASE; i < IRQ_EXTERNAL_BASE + ext_irq_count; ++i)
+		irq_set_chip_and_handler(i, &bcm63xx_external_irq_chip,
+					 handle_edge_irq);
+
+	if (!is_ext_irq_cascaded) {
+		for (i = 3; i < 3 + ext_irq_count; ++i) {
+			irq = MIPS_CPU_IRQ_BASE + i;
+			if (request_irq(irq, no_action, IRQF_NO_THREAD,
+					"cascade_extirq", NULL)) {
+				pr_err("Failed to request irq %d (cascade_extirq)\n",
+				       irq);
+			}
+		}
+	}
+
+	irq = MIPS_CPU_IRQ_BASE + 2;
+	if (request_irq(irq, no_action, IRQF_NO_THREAD,	"cascade_ip2", NULL))
+		pr_err("Failed to request irq %d (cascade_ip2)\n", irq);
+#ifdef CONFIG_SMP
+	if (is_ext_irq_cascaded) {
+		irq = MIPS_CPU_IRQ_BASE + 3;
+		if (request_irq(irq, no_action,	IRQF_NO_THREAD, "cascade_ip3",
+				NULL))
+			pr_err("Failed to request irq %d (cascade_ip3)\n", irq);
+		bcm63xx_internal_irq_chip.irq_set_affinity =
+			bcm63xx_internal_set_affinity;
+
+		cpumask_clear(irq_default_affinity);
+		cpumask_set_cpu(smp_processor_id(), irq_default_affinity);
+	}
+#endif
+}
diff --git a/arch/mips/bcm63xx/nvram.c b/arch/mips/bcm63xx/nvram.c
new file mode 100644
index 000000000..05757aed0
--- /dev/null
+++ b/arch/mips/bcm63xx/nvram.c
@@ -0,0 +1,98 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ * Copyright (C) 2008 Florian Fainelli <florian@openwrt.org>
+ * Copyright (C) 2012 Jonas Gorski <jonas.gorski@gmail.com>
+ */
+
+#define pr_fmt(fmt) "bcm63xx_nvram: " fmt
+
+#include <linux/bcm963xx_nvram.h>
+#include <linux/init.h>
+#include <linux/crc32.h>
+#include <linux/export.h>
+#include <linux/kernel.h>
+#include <linux/if_ether.h>
+
+#include <bcm63xx_nvram.h>
+
+#define BCM63XX_DEFAULT_PSI_SIZE	64
+
+static struct bcm963xx_nvram nvram;
+static int mac_addr_used;
+
+void __init bcm63xx_nvram_init(void *addr)
+{
+	u32 crc, expected_crc;
+	u8 hcs_mac_addr[ETH_ALEN] = { 0x00, 0x10, 0x18, 0xff, 0xff, 0xff };
+
+	/* extract nvram data */
+	memcpy(&nvram, addr, BCM963XX_NVRAM_V5_SIZE);
+
+	/* check checksum before using data */
+	if (bcm963xx_nvram_checksum(&nvram, &expected_crc, &crc))
+		pr_warn("nvram checksum failed, contents may be invalid (expected %08x, got %08x)\n",
+			expected_crc, crc);
+
+	/* Cable modems have a different NVRAM which is embedded in the eCos
+	 * firmware and not easily extractible, give at least a MAC address
+	 * pool.
+	 */
+	if (BCMCPU_IS_3368()) {
+		memcpy(nvram.mac_addr_base, hcs_mac_addr, ETH_ALEN);
+		nvram.mac_addr_count = 2;
+	}
+}
+
+u8 *bcm63xx_nvram_get_name(void)
+{
+	return nvram.name;
+}
+EXPORT_SYMBOL(bcm63xx_nvram_get_name);
+
+int bcm63xx_nvram_get_mac_address(u8 *mac)
+{
+	u8 *oui;
+	int count;
+
+	if (mac_addr_used >= nvram.mac_addr_count) {
+		pr_err("not enough mac addresses\n");
+		return -ENODEV;
+	}
+
+	memcpy(mac, nvram.mac_addr_base, ETH_ALEN);
+	oui = mac + ETH_ALEN/2 - 1;
+	count = mac_addr_used;
+
+	while (count--) {
+		u8 *p = mac + ETH_ALEN - 1;
+
+		do {
+			(*p)++;
+			if (*p != 0)
+				break;
+			p--;
+		} while (p != oui);
+
+		if (p == oui) {
+			pr_err("unable to fetch mac address\n");
+			return -ENODEV;
+		}
+	}
+
+	mac_addr_used++;
+	return 0;
+}
+EXPORT_SYMBOL(bcm63xx_nvram_get_mac_address);
+
+int bcm63xx_nvram_get_psi_size(void)
+{
+	if (nvram.psi_size > 0)
+		return nvram.psi_size;
+
+	return BCM63XX_DEFAULT_PSI_SIZE;
+}
+EXPORT_SYMBOL(bcm63xx_nvram_get_psi_size);
diff --git a/arch/mips/bcm63xx/prom.c b/arch/mips/bcm63xx/prom.c
new file mode 100644
index 000000000..c3a2ea62c
--- /dev/null
+++ b/arch/mips/bcm63xx/prom.c
@@ -0,0 +1,96 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ */
+
+#include <linux/init.h>
+#include <linux/memblock.h>
+#include <linux/smp.h>
+#include <asm/bootinfo.h>
+#include <asm/bmips.h>
+#include <asm/smp-ops.h>
+#include <asm/mipsregs.h>
+#include <bcm63xx_board.h>
+#include <bcm63xx_cpu.h>
+#include <bcm63xx_io.h>
+#include <bcm63xx_regs.h>
+
+void __init prom_init(void)
+{
+	u32 reg, mask;
+
+	bcm63xx_cpu_init();
+
+	/* stop any running watchdog */
+	bcm_wdt_writel(WDT_STOP_1, WDT_CTL_REG);
+	bcm_wdt_writel(WDT_STOP_2, WDT_CTL_REG);
+
+	/* disable all hardware blocks clock for now */
+	if (BCMCPU_IS_3368())
+		mask = CKCTL_3368_ALL_SAFE_EN;
+	else if (BCMCPU_IS_6328())
+		mask = CKCTL_6328_ALL_SAFE_EN;
+	else if (BCMCPU_IS_6338())
+		mask = CKCTL_6338_ALL_SAFE_EN;
+	else if (BCMCPU_IS_6345())
+		mask = CKCTL_6345_ALL_SAFE_EN;
+	else if (BCMCPU_IS_6348())
+		mask = CKCTL_6348_ALL_SAFE_EN;
+	else if (BCMCPU_IS_6358())
+		mask = CKCTL_6358_ALL_SAFE_EN;
+	else if (BCMCPU_IS_6362())
+		mask = CKCTL_6362_ALL_SAFE_EN;
+	else if (BCMCPU_IS_6368())
+		mask = CKCTL_6368_ALL_SAFE_EN;
+	else
+		mask = 0;
+
+	reg = bcm_perf_readl(PERF_CKCTL_REG);
+	reg &= ~mask;
+	bcm_perf_writel(reg, PERF_CKCTL_REG);
+
+	/* do low level board init */
+	board_prom_init();
+
+	/* set up SMP */
+	if (!register_bmips_smp_ops()) {
+		/*
+		 * BCM6328 might not have its second CPU enabled, while BCM3368
+		 * and BCM6358 need special handling for their shared TLB, so
+		 * disable SMP for now.
+		 */
+		if (BCMCPU_IS_6328()) {
+			reg = bcm_readl(BCM_6328_OTP_BASE +
+					OTP_USER_BITS_6328_REG(3));
+
+			if (reg & OTP_6328_REG3_TP1_DISABLED)
+				bmips_smp_enabled = 0;
+		} else if (BCMCPU_IS_3368() || BCMCPU_IS_6358()) {
+			bmips_smp_enabled = 0;
+		}
+
+		if (!bmips_smp_enabled)
+			return;
+
+		/*
+		 * The bootloader has set up the CPU1 reset vector at
+		 * 0xa000_0200.
+		 * This conflicts with the special interrupt vector (IV).
+		 * The bootloader has also set up CPU1 to respond to the wrong
+		 * IPI interrupt.
+		 * Here we will start up CPU1 in the background and ask it to
+		 * reconfigure itself then go back to sleep.
+		 */
+		memcpy((void *)0xa0000200, bmips_smp_movevec, 0x20);
+		__sync();
+		set_c0_cause(C_SW0);
+		cpumask_set_cpu(1, &bmips_booted_mask);
+
+		/*
+		 * FIXME: we really should have some sort of hazard barrier here
+		 */
+	}
+}
diff --git a/arch/mips/bcm63xx/reset.c b/arch/mips/bcm63xx/reset.c
new file mode 100644
index 000000000..64574e74c
--- /dev/null
+++ b/arch/mips/bcm63xx/reset.c
@@ -0,0 +1,219 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2012 Jonas Gorski <jonas.gorski@gmail.com>
+ */
+
+#include <linux/init.h>
+#include <linux/export.h>
+#include <linux/mutex.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <bcm63xx_cpu.h>
+#include <bcm63xx_io.h>
+#include <bcm63xx_regs.h>
+#include <bcm63xx_reset.h>
+
+#define __GEN_RESET_BITS_TABLE(__cpu)					\
+	[BCM63XX_RESET_SPI]		= BCM## __cpu ##_RESET_SPI,	\
+	[BCM63XX_RESET_ENET]		= BCM## __cpu ##_RESET_ENET,	\
+	[BCM63XX_RESET_USBH]		= BCM## __cpu ##_RESET_USBH,	\
+	[BCM63XX_RESET_USBD]		= BCM## __cpu ##_RESET_USBD,	\
+	[BCM63XX_RESET_DSL]		= BCM## __cpu ##_RESET_DSL,	\
+	[BCM63XX_RESET_SAR]		= BCM## __cpu ##_RESET_SAR,	\
+	[BCM63XX_RESET_EPHY]		= BCM## __cpu ##_RESET_EPHY,	\
+	[BCM63XX_RESET_ENETSW]		= BCM## __cpu ##_RESET_ENETSW,	\
+	[BCM63XX_RESET_PCM]		= BCM## __cpu ##_RESET_PCM,	\
+	[BCM63XX_RESET_MPI]		= BCM## __cpu ##_RESET_MPI,	\
+	[BCM63XX_RESET_PCIE]		= BCM## __cpu ##_RESET_PCIE,	\
+	[BCM63XX_RESET_PCIE_EXT]	= BCM## __cpu ##_RESET_PCIE_EXT,
+
+#define BCM3368_RESET_SPI	SOFTRESET_3368_SPI_MASK
+#define BCM3368_RESET_ENET	SOFTRESET_3368_ENET_MASK
+#define BCM3368_RESET_USBH	0
+#define BCM3368_RESET_USBD	SOFTRESET_3368_USBS_MASK
+#define BCM3368_RESET_DSL	0
+#define BCM3368_RESET_SAR	0
+#define BCM3368_RESET_EPHY	SOFTRESET_3368_EPHY_MASK
+#define BCM3368_RESET_ENETSW	0
+#define BCM3368_RESET_PCM	SOFTRESET_3368_PCM_MASK
+#define BCM3368_RESET_MPI	SOFTRESET_3368_MPI_MASK
+#define BCM3368_RESET_PCIE	0
+#define BCM3368_RESET_PCIE_EXT	0
+
+#define BCM6328_RESET_SPI	SOFTRESET_6328_SPI_MASK
+#define BCM6328_RESET_ENET	0
+#define BCM6328_RESET_USBH	SOFTRESET_6328_USBH_MASK
+#define BCM6328_RESET_USBD	SOFTRESET_6328_USBS_MASK
+#define BCM6328_RESET_DSL	0
+#define BCM6328_RESET_SAR	SOFTRESET_6328_SAR_MASK
+#define BCM6328_RESET_EPHY	SOFTRESET_6328_EPHY_MASK
+#define BCM6328_RESET_ENETSW	SOFTRESET_6328_ENETSW_MASK
+#define BCM6328_RESET_PCM	SOFTRESET_6328_PCM_MASK
+#define BCM6328_RESET_MPI	0
+#define BCM6328_RESET_PCIE	\
+				(SOFTRESET_6328_PCIE_MASK |		\
+				 SOFTRESET_6328_PCIE_CORE_MASK |	\
+				 SOFTRESET_6328_PCIE_HARD_MASK)
+#define BCM6328_RESET_PCIE_EXT	SOFTRESET_6328_PCIE_EXT_MASK
+
+#define BCM6338_RESET_SPI	SOFTRESET_6338_SPI_MASK
+#define BCM6338_RESET_ENET	SOFTRESET_6338_ENET_MASK
+#define BCM6338_RESET_USBH	SOFTRESET_6338_USBH_MASK
+#define BCM6338_RESET_USBD	SOFTRESET_6338_USBS_MASK
+#define BCM6338_RESET_DSL	SOFTRESET_6338_ADSL_MASK
+#define BCM6338_RESET_SAR	SOFTRESET_6338_SAR_MASK
+#define BCM6338_RESET_EPHY	0
+#define BCM6338_RESET_ENETSW	0
+#define BCM6338_RESET_PCM	0
+#define BCM6338_RESET_MPI	0
+#define BCM6338_RESET_PCIE	0
+#define BCM6338_RESET_PCIE_EXT	0
+
+#define BCM6348_RESET_SPI	SOFTRESET_6348_SPI_MASK
+#define BCM6348_RESET_ENET	SOFTRESET_6348_ENET_MASK
+#define BCM6348_RESET_USBH	SOFTRESET_6348_USBH_MASK
+#define BCM6348_RESET_USBD	SOFTRESET_6348_USBS_MASK
+#define BCM6348_RESET_DSL	SOFTRESET_6348_ADSL_MASK
+#define BCM6348_RESET_SAR	SOFTRESET_6348_SAR_MASK
+#define BCM6348_RESET_EPHY	0
+#define BCM6348_RESET_ENETSW	0
+#define BCM6348_RESET_PCM	0
+#define BCM6348_RESET_MPI	0
+#define BCM6348_RESET_PCIE	0
+#define BCM6348_RESET_PCIE_EXT	0
+
+#define BCM6358_RESET_SPI	SOFTRESET_6358_SPI_MASK
+#define BCM6358_RESET_ENET	SOFTRESET_6358_ENET_MASK
+#define BCM6358_RESET_USBH	SOFTRESET_6358_USBH_MASK
+#define BCM6358_RESET_USBD	0
+#define BCM6358_RESET_DSL	SOFTRESET_6358_ADSL_MASK
+#define BCM6358_RESET_SAR	SOFTRESET_6358_SAR_MASK
+#define BCM6358_RESET_EPHY	SOFTRESET_6358_EPHY_MASK
+#define BCM6358_RESET_ENETSW	0
+#define BCM6358_RESET_PCM	SOFTRESET_6358_PCM_MASK
+#define BCM6358_RESET_MPI	SOFTRESET_6358_MPI_MASK
+#define BCM6358_RESET_PCIE	0
+#define BCM6358_RESET_PCIE_EXT	0
+
+#define BCM6362_RESET_SPI	SOFTRESET_6362_SPI_MASK
+#define BCM6362_RESET_ENET	0
+#define BCM6362_RESET_USBH	SOFTRESET_6362_USBH_MASK
+#define BCM6362_RESET_USBD	SOFTRESET_6362_USBS_MASK
+#define BCM6362_RESET_DSL	0
+#define BCM6362_RESET_SAR	SOFTRESET_6362_SAR_MASK
+#define BCM6362_RESET_EPHY	SOFTRESET_6362_EPHY_MASK
+#define BCM6362_RESET_ENETSW	SOFTRESET_6362_ENETSW_MASK
+#define BCM6362_RESET_PCM	SOFTRESET_6362_PCM_MASK
+#define BCM6362_RESET_MPI	0
+#define BCM6362_RESET_PCIE      (SOFTRESET_6362_PCIE_MASK | \
+				 SOFTRESET_6362_PCIE_CORE_MASK)
+#define BCM6362_RESET_PCIE_EXT	SOFTRESET_6362_PCIE_EXT_MASK
+
+#define BCM6368_RESET_SPI	SOFTRESET_6368_SPI_MASK
+#define BCM6368_RESET_ENET	0
+#define BCM6368_RESET_USBH	SOFTRESET_6368_USBH_MASK
+#define BCM6368_RESET_USBD	SOFTRESET_6368_USBS_MASK
+#define BCM6368_RESET_DSL	0
+#define BCM6368_RESET_SAR	SOFTRESET_6368_SAR_MASK
+#define BCM6368_RESET_EPHY	SOFTRESET_6368_EPHY_MASK
+#define BCM6368_RESET_ENETSW	SOFTRESET_6368_ENETSW_MASK
+#define BCM6368_RESET_PCM	SOFTRESET_6368_PCM_MASK
+#define BCM6368_RESET_MPI	SOFTRESET_6368_MPI_MASK
+#define BCM6368_RESET_PCIE	0
+#define BCM6368_RESET_PCIE_EXT	0
+
+/*
+ * core reset bits
+ */
+static const u32 bcm3368_reset_bits[] = {
+	__GEN_RESET_BITS_TABLE(3368)
+};
+
+static const u32 bcm6328_reset_bits[] = {
+	__GEN_RESET_BITS_TABLE(6328)
+};
+
+static const u32 bcm6338_reset_bits[] = {
+	__GEN_RESET_BITS_TABLE(6338)
+};
+
+static const u32 bcm6348_reset_bits[] = {
+	__GEN_RESET_BITS_TABLE(6348)
+};
+
+static const u32 bcm6358_reset_bits[] = {
+	__GEN_RESET_BITS_TABLE(6358)
+};
+
+static const u32 bcm6362_reset_bits[] = {
+	__GEN_RESET_BITS_TABLE(6362)
+};
+
+static const u32 bcm6368_reset_bits[] = {
+	__GEN_RESET_BITS_TABLE(6368)
+};
+
+const u32 *bcm63xx_reset_bits;
+static int reset_reg;
+
+static int __init bcm63xx_reset_bits_init(void)
+{
+	if (BCMCPU_IS_3368()) {
+		reset_reg = PERF_SOFTRESET_6358_REG;
+		bcm63xx_reset_bits = bcm3368_reset_bits;
+	} else if (BCMCPU_IS_6328()) {
+		reset_reg = PERF_SOFTRESET_6328_REG;
+		bcm63xx_reset_bits = bcm6328_reset_bits;
+	} else if (BCMCPU_IS_6338()) {
+		reset_reg = PERF_SOFTRESET_REG;
+		bcm63xx_reset_bits = bcm6338_reset_bits;
+	} else if (BCMCPU_IS_6348()) {
+		reset_reg = PERF_SOFTRESET_REG;
+		bcm63xx_reset_bits = bcm6348_reset_bits;
+	} else if (BCMCPU_IS_6358()) {
+		reset_reg = PERF_SOFTRESET_6358_REG;
+		bcm63xx_reset_bits = bcm6358_reset_bits;
+	} else if (BCMCPU_IS_6362()) {
+		reset_reg = PERF_SOFTRESET_6362_REG;
+		bcm63xx_reset_bits = bcm6362_reset_bits;
+	} else if (BCMCPU_IS_6368()) {
+		reset_reg = PERF_SOFTRESET_6368_REG;
+		bcm63xx_reset_bits = bcm6368_reset_bits;
+	}
+
+	return 0;
+}
+
+static DEFINE_SPINLOCK(reset_mutex);
+
+static void __bcm63xx_core_set_reset(u32 mask, int enable)
+{
+	unsigned long flags;
+	u32 val;
+
+	if (!mask)
+		return;
+
+	spin_lock_irqsave(&reset_mutex, flags);
+	val = bcm_perf_readl(reset_reg);
+
+	if (enable)
+		val &= ~mask;
+	else
+		val |= mask;
+
+	bcm_perf_writel(val, reset_reg);
+	spin_unlock_irqrestore(&reset_mutex, flags);
+}
+
+void bcm63xx_core_set_reset(enum bcm63xx_core_reset core, int reset)
+{
+	__bcm63xx_core_set_reset(bcm63xx_reset_bits[core], reset);
+}
+EXPORT_SYMBOL(bcm63xx_core_set_reset);
+
+postcore_initcall(bcm63xx_reset_bits_init);
diff --git a/arch/mips/bcm63xx/setup.c b/arch/mips/bcm63xx/setup.c
new file mode 100644
index 000000000..d811e3e03
--- /dev/null
+++ b/arch/mips/bcm63xx/setup.c
@@ -0,0 +1,170 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/memblock.h>
+#include <linux/ioport.h>
+#include <linux/pm.h>
+#include <asm/bootinfo.h>
+#include <asm/time.h>
+#include <asm/reboot.h>
+#include <asm/cacheflush.h>
+#include <bcm63xx_board.h>
+#include <bcm63xx_cpu.h>
+#include <bcm63xx_regs.h>
+#include <bcm63xx_io.h>
+#include <bcm63xx_gpio.h>
+
+void bcm63xx_machine_halt(void)
+{
+	pr_info("System halted\n");
+	while (1)
+		;
+}
+
+static void bcm6348_a1_reboot(void)
+{
+	u32 reg;
+
+	/* soft reset all blocks */
+	pr_info("soft-resetting all blocks ...\n");
+	reg = bcm_perf_readl(PERF_SOFTRESET_REG);
+	reg &= ~SOFTRESET_6348_ALL;
+	bcm_perf_writel(reg, PERF_SOFTRESET_REG);
+	mdelay(10);
+
+	reg = bcm_perf_readl(PERF_SOFTRESET_REG);
+	reg |= SOFTRESET_6348_ALL;
+	bcm_perf_writel(reg, PERF_SOFTRESET_REG);
+	mdelay(10);
+
+	/* Jump to the power on address. */
+	pr_info("jumping to reset vector.\n");
+	/* set high vectors (base at 0xbfc00000 */
+	set_c0_status(ST0_BEV | ST0_ERL);
+	/* run uncached in kseg0 */
+	change_c0_config(CONF_CM_CMASK, CONF_CM_UNCACHED);
+	__flush_cache_all();
+	/* remove all wired TLB entries */
+	write_c0_wired(0);
+	__asm__ __volatile__(
+		"jr\t%0"
+		:
+		: "r" (0xbfc00000));
+	while (1)
+		;
+}
+
+void bcm63xx_machine_reboot(void)
+{
+	u32 reg, perf_regs[2] = { 0, 0 };
+	unsigned int i;
+
+	/* mask and clear all external irq */
+	switch (bcm63xx_get_cpu_id()) {
+	case BCM3368_CPU_ID:
+		perf_regs[0] = PERF_EXTIRQ_CFG_REG_3368;
+		break;
+	case BCM6328_CPU_ID:
+		perf_regs[0] = PERF_EXTIRQ_CFG_REG_6328;
+		break;
+	case BCM6338_CPU_ID:
+		perf_regs[0] = PERF_EXTIRQ_CFG_REG_6338;
+		break;
+	case BCM6345_CPU_ID:
+		perf_regs[0] = PERF_EXTIRQ_CFG_REG_6345;
+		break;
+	case BCM6348_CPU_ID:
+		perf_regs[0] = PERF_EXTIRQ_CFG_REG_6348;
+		break;
+	case BCM6358_CPU_ID:
+		perf_regs[0] = PERF_EXTIRQ_CFG_REG_6358;
+		break;
+	case BCM6362_CPU_ID:
+		perf_regs[0] = PERF_EXTIRQ_CFG_REG_6362;
+		break;
+	}
+
+	for (i = 0; i < 2; i++) {
+		if (!perf_regs[i])
+			break;
+
+		reg = bcm_perf_readl(perf_regs[i]);
+		if (BCMCPU_IS_6348()) {
+			reg &= ~EXTIRQ_CFG_MASK_ALL_6348;
+			reg |= EXTIRQ_CFG_CLEAR_ALL_6348;
+		} else {
+			reg &= ~EXTIRQ_CFG_MASK_ALL;
+			reg |= EXTIRQ_CFG_CLEAR_ALL;
+		}
+		bcm_perf_writel(reg, perf_regs[i]);
+	}
+
+	if (BCMCPU_IS_6348() && (bcm63xx_get_cpu_rev() == 0xa1))
+		bcm6348_a1_reboot();
+
+	pr_info("triggering watchdog soft-reset...\n");
+	if (BCMCPU_IS_6328()) {
+		bcm_wdt_writel(1, WDT_SOFTRESET_REG);
+	} else {
+		reg = bcm_perf_readl(PERF_SYS_PLL_CTL_REG);
+		reg |= SYS_PLL_SOFT_RESET;
+		bcm_perf_writel(reg, PERF_SYS_PLL_CTL_REG);
+	}
+	while (1)
+		;
+}
+
+static void __bcm63xx_machine_reboot(char *p)
+{
+	bcm63xx_machine_reboot();
+}
+
+/*
+ * return system type in /proc/cpuinfo
+ */
+const char *get_system_type(void)
+{
+	static char buf[128];
+	snprintf(buf, sizeof(buf), "bcm63xx/%s (0x%04x/0x%02X)",
+		 board_get_name(),
+		 bcm63xx_get_cpu_id(), bcm63xx_get_cpu_rev());
+	return buf;
+}
+
+void __init plat_time_init(void)
+{
+	mips_hpt_frequency = bcm63xx_get_cpu_freq() / 2;
+}
+
+void __init plat_mem_setup(void)
+{
+	memblock_add(0, bcm63xx_get_memory_size());
+
+	_machine_halt = bcm63xx_machine_halt;
+	_machine_restart = __bcm63xx_machine_reboot;
+	pm_power_off = bcm63xx_machine_halt;
+
+	set_io_port_base(0);
+	ioport_resource.start = 0;
+	ioport_resource.end = ~0;
+
+	board_setup();
+}
+
+int __init bcm63xx_register_devices(void)
+{
+	/* register gpiochip */
+	bcm63xx_gpio_init();
+
+	return board_register_devices();
+}
+
+arch_initcall(bcm63xx_register_devices);
diff --git a/arch/mips/bcm63xx/timer.c b/arch/mips/bcm63xx/timer.c
new file mode 100644
index 000000000..a86065854
--- /dev/null
+++ b/arch/mips/bcm63xx/timer.c
@@ -0,0 +1,206 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ */
+
+#include <linux/kernel.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/export.h>
+#include <linux/spinlock.h>
+#include <linux/interrupt.h>
+#include <linux/clk.h>
+#include <bcm63xx_cpu.h>
+#include <bcm63xx_io.h>
+#include <bcm63xx_timer.h>
+#include <bcm63xx_regs.h>
+
+static DEFINE_RAW_SPINLOCK(timer_reg_lock);
+static DEFINE_RAW_SPINLOCK(timer_data_lock);
+static struct clk *periph_clk;
+
+static struct timer_data {
+	void	(*cb)(void *);
+	void	*data;
+} timer_data[BCM63XX_TIMER_COUNT];
+
+static irqreturn_t timer_interrupt(int irq, void *dev_id)
+{
+	u32 stat;
+	int i;
+
+	raw_spin_lock(&timer_reg_lock);
+	stat = bcm_timer_readl(TIMER_IRQSTAT_REG);
+	bcm_timer_writel(stat, TIMER_IRQSTAT_REG);
+	raw_spin_unlock(&timer_reg_lock);
+
+	for (i = 0; i < BCM63XX_TIMER_COUNT; i++) {
+		if (!(stat & TIMER_IRQSTAT_TIMER_CAUSE(i)))
+			continue;
+
+		raw_spin_lock(&timer_data_lock);
+		if (!timer_data[i].cb) {
+			raw_spin_unlock(&timer_data_lock);
+			continue;
+		}
+
+		timer_data[i].cb(timer_data[i].data);
+		raw_spin_unlock(&timer_data_lock);
+	}
+
+	return IRQ_HANDLED;
+}
+
+int bcm63xx_timer_enable(int id)
+{
+	u32 reg;
+	unsigned long flags;
+
+	if (id >= BCM63XX_TIMER_COUNT)
+		return -EINVAL;
+
+	raw_spin_lock_irqsave(&timer_reg_lock, flags);
+
+	reg = bcm_timer_readl(TIMER_CTLx_REG(id));
+	reg |= TIMER_CTL_ENABLE_MASK;
+	bcm_timer_writel(reg, TIMER_CTLx_REG(id));
+
+	reg = bcm_timer_readl(TIMER_IRQSTAT_REG);
+	reg |= TIMER_IRQSTAT_TIMER_IR_EN(id);
+	bcm_timer_writel(reg, TIMER_IRQSTAT_REG);
+
+	raw_spin_unlock_irqrestore(&timer_reg_lock, flags);
+	return 0;
+}
+
+EXPORT_SYMBOL(bcm63xx_timer_enable);
+
+int bcm63xx_timer_disable(int id)
+{
+	u32 reg;
+	unsigned long flags;
+
+	if (id >= BCM63XX_TIMER_COUNT)
+		return -EINVAL;
+
+	raw_spin_lock_irqsave(&timer_reg_lock, flags);
+
+	reg = bcm_timer_readl(TIMER_CTLx_REG(id));
+	reg &= ~TIMER_CTL_ENABLE_MASK;
+	bcm_timer_writel(reg, TIMER_CTLx_REG(id));
+
+	reg = bcm_timer_readl(TIMER_IRQSTAT_REG);
+	reg &= ~TIMER_IRQSTAT_TIMER_IR_EN(id);
+	bcm_timer_writel(reg, TIMER_IRQSTAT_REG);
+
+	raw_spin_unlock_irqrestore(&timer_reg_lock, flags);
+	return 0;
+}
+
+EXPORT_SYMBOL(bcm63xx_timer_disable);
+
+int bcm63xx_timer_register(int id, void (*callback)(void *data), void *data)
+{
+	unsigned long flags;
+	int ret;
+
+	if (id >= BCM63XX_TIMER_COUNT || !callback)
+		return -EINVAL;
+
+	ret = 0;
+	raw_spin_lock_irqsave(&timer_data_lock, flags);
+	if (timer_data[id].cb) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	timer_data[id].cb = callback;
+	timer_data[id].data = data;
+
+out:
+	raw_spin_unlock_irqrestore(&timer_data_lock, flags);
+	return ret;
+}
+
+EXPORT_SYMBOL(bcm63xx_timer_register);
+
+void bcm63xx_timer_unregister(int id)
+{
+	unsigned long flags;
+
+	if (id >= BCM63XX_TIMER_COUNT)
+		return;
+
+	raw_spin_lock_irqsave(&timer_data_lock, flags);
+	timer_data[id].cb = NULL;
+	raw_spin_unlock_irqrestore(&timer_data_lock, flags);
+}
+
+EXPORT_SYMBOL(bcm63xx_timer_unregister);
+
+unsigned int bcm63xx_timer_countdown(unsigned int countdown_us)
+{
+	return (clk_get_rate(periph_clk) / (1000 * 1000)) * countdown_us;
+}
+
+EXPORT_SYMBOL(bcm63xx_timer_countdown);
+
+int bcm63xx_timer_set(int id, int monotonic, unsigned int countdown_us)
+{
+	u32 reg, countdown;
+	unsigned long flags;
+
+	if (id >= BCM63XX_TIMER_COUNT)
+		return -EINVAL;
+
+	countdown = bcm63xx_timer_countdown(countdown_us);
+	if (countdown & ~TIMER_CTL_COUNTDOWN_MASK)
+		return -EINVAL;
+
+	raw_spin_lock_irqsave(&timer_reg_lock, flags);
+	reg = bcm_timer_readl(TIMER_CTLx_REG(id));
+
+	if (monotonic)
+		reg &= ~TIMER_CTL_MONOTONIC_MASK;
+	else
+		reg |= TIMER_CTL_MONOTONIC_MASK;
+
+	reg &= ~TIMER_CTL_COUNTDOWN_MASK;
+	reg |= countdown;
+	bcm_timer_writel(reg, TIMER_CTLx_REG(id));
+
+	raw_spin_unlock_irqrestore(&timer_reg_lock, flags);
+	return 0;
+}
+
+EXPORT_SYMBOL(bcm63xx_timer_set);
+
+int bcm63xx_timer_init(void)
+{
+	int ret, irq;
+	u32 reg;
+
+	reg = bcm_timer_readl(TIMER_IRQSTAT_REG);
+	reg &= ~TIMER_IRQSTAT_TIMER0_IR_EN;
+	reg &= ~TIMER_IRQSTAT_TIMER1_IR_EN;
+	reg &= ~TIMER_IRQSTAT_TIMER2_IR_EN;
+	bcm_timer_writel(reg, TIMER_IRQSTAT_REG);
+
+	periph_clk = clk_get(NULL, "periph");
+	if (IS_ERR(periph_clk))
+		return -ENODEV;
+
+	irq = bcm63xx_get_irq_number(IRQ_TIMER);
+	ret = request_irq(irq, timer_interrupt, 0, "bcm63xx_timer", NULL);
+	if (ret) {
+		pr_err("%s: failed to register irq\n", __func__);
+		return ret;
+	}
+
+	return 0;
+}
+
+arch_initcall(bcm63xx_timer_init);
diff --git a/arch/mips/bmips/Kconfig b/arch/mips/bmips/Kconfig
new file mode 100644
index 000000000..63dfc6950
--- /dev/null
+++ b/arch/mips/bmips/Kconfig
@@ -0,0 +1,83 @@
+# SPDX-License-Identifier: GPL-2.0
+if BMIPS_GENERIC
+
+choice
+	prompt "Built-in device tree"
+	help
+	  Legacy bootloaders do not pass a DTB pointer to the kernel, so
+	  if a "wrapper" is not being used, the kernel will need to include
+	  a device tree that matches the target board.
+
+	  The builtin DTB will only be used if the firmware does not supply
+	  a valid DTB.
+
+config DT_NONE
+	bool "None"
+
+config DT_BCM93384WVG
+	bool "BCM93384WVG Zephyr CPU"
+	select BUILTIN_DTB
+
+config DT_BCM93384WVG_VIPER
+	bool "BCM93384WVG Viper CPU (EXPERIMENTAL)"
+	select BUILTIN_DTB
+
+config DT_BCM96368MVWG
+	bool "BCM96368MVWG"
+	select BUILTIN_DTB
+
+config DT_BCM9EJTAGPRB
+	bool "BCM9EJTAGPRB"
+	select BUILTIN_DTB
+
+config DT_BCM97125CBMB
+	bool "BCM97125CBMB"
+	select BUILTIN_DTB
+
+config DT_BCM97346DBSMB
+	bool "BCM97346DBSMB"
+	select BUILTIN_DTB
+
+config DT_BCM97358SVMB
+	bool "BCM97358SVMB"
+	select BUILTIN_DTB
+
+config DT_BCM97360SVMB
+	bool "BCM97360SVMB"
+	select BUILTIN_DTB
+
+config DT_BCM97362SVMB
+	bool "BCM97362SVMB"
+	select BUILTIN_DTB
+
+config DT_BCM97420C
+	bool "BCM97420C"
+	select BUILTIN_DTB
+
+config DT_BCM97425SVMB
+	bool "BCM97425SVMB"
+	select BUILTIN_DTB
+
+config DT_BCM97435SVMB
+	bool "BCM97435SVMB"
+	select BUILTIN_DTB
+
+config DT_COMTREND_VR3032U
+	bool "Comtrend VR-3032u"
+	select BUILTIN_DTB
+
+config DT_NETGEAR_CVG834G
+	bool "NETGEAR CVG834G"
+	select BUILTIN_DTB
+
+config DT_SFR_NEUFBOX4_SERCOMM
+	bool "SFR Neufbox 4 (Sercomm)"
+	select BUILTIN_DTB
+
+config DT_SFR_NEUFBOX6_SERCOMM
+	bool "SFR Neufbox 6 (Sercomm)"
+	select BUILTIN_DTB
+
+endchoice
+
+endif
diff --git a/arch/mips/bmips/Makefile b/arch/mips/bmips/Makefile
new file mode 100644
index 000000000..1165bf2ef
--- /dev/null
+++ b/arch/mips/bmips/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0-only
+obj-y		+= setup.o irq.o dma.o
diff --git a/arch/mips/bmips/Platform b/arch/mips/bmips/Platform
new file mode 100644
index 000000000..1434ea31c
--- /dev/null
+++ b/arch/mips/bmips/Platform
@@ -0,0 +1,6 @@
+#
+# Broadcom Generic BMIPS kernel
+#
+cflags-$(CONFIG_BMIPS_GENERIC)		+=				\
+		-I$(srctree)/arch/mips/include/asm/mach-bmips/
+load-$(CONFIG_BMIPS_GENERIC)		:= 0xffffffff80010000
diff --git a/arch/mips/bmips/dma.c b/arch/mips/bmips/dma.c
new file mode 100644
index 000000000..3779e7855
--- /dev/null
+++ b/arch/mips/bmips/dma.c
@@ -0,0 +1,27 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include <linux/types.h>
+#include <linux/dma-map-ops.h>
+#include <asm/bmips.h>
+#include <asm/io.h>
+
+bool bmips_rac_flush_disable;
+
+void arch_sync_dma_for_cpu_all(void)
+{
+	void __iomem *cbr = BMIPS_GET_CBR();
+	u32 cfg;
+
+	if (boot_cpu_type() != CPU_BMIPS3300 &&
+	    boot_cpu_type() != CPU_BMIPS4350 &&
+	    boot_cpu_type() != CPU_BMIPS4380)
+		return;
+
+	if (unlikely(bmips_rac_flush_disable))
+		return;
+
+	/* Flush stale data out of the readahead cache */
+	cfg = __raw_readl(cbr + BMIPS_RAC_CONFIG);
+	__raw_writel(cfg | 0x100, cbr + BMIPS_RAC_CONFIG);
+	__raw_readl(cbr + BMIPS_RAC_CONFIG);
+}
diff --git a/arch/mips/bmips/irq.c b/arch/mips/bmips/irq.c
new file mode 100644
index 000000000..c4daa590b
--- /dev/null
+++ b/arch/mips/bmips/irq.c
@@ -0,0 +1,42 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ * Copyright (C) 2014 Broadcom Corporation
+ * Author: Kevin Cernekee <cernekee@gmail.com>
+ */
+
+#include <linux/of.h>
+#include <linux/irqchip.h>
+
+#include <asm/bmips.h>
+#include <asm/irq.h>
+#include <asm/irq_cpu.h>
+#include <asm/time.h>
+
+static const struct of_device_id smp_intc_dt_match[] = {
+	{ .compatible = "brcm,bcm7038-l1-intc" },
+	{ .compatible = "brcm,bcm6345-l1-intc" },
+	{}
+};
+
+unsigned int get_c0_compare_int(void)
+{
+	return CP0_LEGACY_COMPARE_IRQ;
+}
+
+void __init arch_init_irq(void)
+{
+	struct device_node *dn;
+
+	/* Only these controllers support SMP IRQ affinity */
+	dn = of_find_matching_node(NULL, smp_intc_dt_match);
+	if (dn)
+		of_node_put(dn);
+	else
+		bmips_tp1_irqs = 0;
+
+	irqchip_init();
+}
+
+IRQCHIP_DECLARE(mips_cpu_intc, "mti,cpu-interrupt-controller",
+	     mips_cpu_irq_of_init);
diff --git a/arch/mips/bmips/setup.c b/arch/mips/bmips/setup.c
new file mode 100644
index 000000000..549a6392a
--- /dev/null
+++ b/arch/mips/bmips/setup.c
@@ -0,0 +1,219 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ * Copyright (C) 2014 Kevin Cernekee <cernekee@gmail.com>
+ */
+
+#include <linux/init.h>
+#include <linux/bitops.h>
+#include <linux/memblock.h>
+#include <linux/ioport.h>
+#include <linux/kernel.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_clk.h>
+#include <linux/of_fdt.h>
+#include <linux/of_platform.h>
+#include <linux/libfdt.h>
+#include <linux/smp.h>
+#include <asm/addrspace.h>
+#include <asm/bmips.h>
+#include <asm/bootinfo.h>
+#include <asm/cpu-type.h>
+#include <asm/mipsregs.h>
+#include <asm/prom.h>
+#include <asm/smp-ops.h>
+#include <asm/time.h>
+#include <asm/traps.h>
+#include <asm/fw/cfe/cfe_api.h>
+
+#define RELO_NORMAL_VEC		BIT(18)
+
+#define REG_BCM6328_OTP		((void __iomem *)CKSEG1ADDR(0x1000062c))
+#define BCM6328_TP1_DISABLED	BIT(9)
+
+extern bool bmips_rac_flush_disable;
+
+static const unsigned long kbase = VMLINUX_LOAD_ADDRESS & 0xfff00000;
+
+struct bmips_quirk {
+	const char		*compatible;
+	void			(*quirk_fn)(void);
+};
+
+static void kbase_setup(void)
+{
+	__raw_writel(kbase | RELO_NORMAL_VEC,
+		     BMIPS_GET_CBR() + BMIPS_RELO_VECTOR_CONTROL_1);
+	ebase = kbase;
+}
+
+static void bcm3384_viper_quirks(void)
+{
+	/*
+	 * Some experimental CM boxes are set up to let CM own the Viper TP0
+	 * and let Linux own TP1.  This requires moving the kernel
+	 * load address to a non-conflicting region (e.g. via
+	 * CONFIG_PHYSICAL_START) and supplying an alternate DTB.
+	 * If we detect this condition, we need to move the MIPS exception
+	 * vectors up to an area that we own.
+	 *
+	 * This is distinct from the OTHER special case mentioned in
+	 * smp-bmips.c (boot on TP1, but enable SMP, then TP0 becomes our
+	 * logical CPU#1).  For the Viper TP1 case, SMP is off limits.
+	 *
+	 * Also note that many BMIPS435x CPUs do not have a
+	 * BMIPS_RELO_VECTOR_CONTROL_1 register, so it isn't safe to just
+	 * write VMLINUX_LOAD_ADDRESS into that register on every SoC.
+	 */
+	board_ebase_setup = &kbase_setup;
+	bmips_smp_enabled = 0;
+}
+
+static void bcm63xx_fixup_cpu1(void)
+{
+	/*
+	 * The bootloader has set up the CPU1 reset vector at
+	 * 0xa000_0200.
+	 * This conflicts with the special interrupt vector (IV).
+	 * The bootloader has also set up CPU1 to respond to the wrong
+	 * IPI interrupt.
+	 * Here we will start up CPU1 in the background and ask it to
+	 * reconfigure itself then go back to sleep.
+	 */
+	memcpy((void *)0xa0000200, &bmips_smp_movevec, 0x20);
+	__sync();
+	set_c0_cause(C_SW0);
+	cpumask_set_cpu(1, &bmips_booted_mask);
+}
+
+static void bcm6328_quirks(void)
+{
+	/* Check CPU1 status in OTP (it is usually disabled) */
+	if (__raw_readl(REG_BCM6328_OTP) & BCM6328_TP1_DISABLED)
+		bmips_smp_enabled = 0;
+	else
+		bcm63xx_fixup_cpu1();
+}
+
+static void bcm6358_quirks(void)
+{
+	/*
+	 * BCM3368/BCM6358 need special handling for their shared TLB, so
+	 * disable SMP for now
+	 */
+	bmips_smp_enabled = 0;
+
+	/*
+	 * RAC flush causes kernel panics on BCM6358 when booting from TP1
+	 * because the bootloader is not initializing it properly.
+	 */
+	bmips_rac_flush_disable = !!(read_c0_brcm_cmt_local() & (1 << 31));
+}
+
+static void bcm6368_quirks(void)
+{
+	bcm63xx_fixup_cpu1();
+}
+
+static const struct bmips_quirk bmips_quirk_list[] = {
+	{ "brcm,bcm3368",		&bcm6358_quirks			},
+	{ "brcm,bcm3384-viper",		&bcm3384_viper_quirks		},
+	{ "brcm,bcm33843-viper",	&bcm3384_viper_quirks		},
+	{ "brcm,bcm6328",		&bcm6328_quirks			},
+	{ "brcm,bcm6358",		&bcm6358_quirks			},
+	{ "brcm,bcm6362",		&bcm6368_quirks			},
+	{ "brcm,bcm6368",		&bcm6368_quirks			},
+	{ "brcm,bcm63168",		&bcm6368_quirks			},
+	{ "brcm,bcm63268",		&bcm6368_quirks			},
+	{ },
+};
+
+static void __init bmips_init_cfe(void)
+{
+	cfe_seal = fw_arg3;
+
+	if (cfe_seal != CFE_EPTSEAL)
+		return;
+
+	cfe_init(fw_arg0, fw_arg2);
+}
+
+void __init prom_init(void)
+{
+	bmips_init_cfe();
+	bmips_cpu_setup();
+	register_bmips_smp_ops();
+}
+
+const char *get_system_type(void)
+{
+	return "Generic BMIPS kernel";
+}
+
+void __init plat_time_init(void)
+{
+	struct device_node *np;
+	u32 freq;
+
+	np = of_find_node_by_name(NULL, "cpus");
+	if (!np)
+		panic("missing 'cpus' DT node");
+	if (of_property_read_u32(np, "mips-hpt-frequency", &freq) < 0)
+		panic("missing 'mips-hpt-frequency' property");
+	of_node_put(np);
+
+	mips_hpt_frequency = freq;
+}
+
+void __init plat_mem_setup(void)
+{
+	void *dtb;
+	const struct bmips_quirk *q;
+
+	set_io_port_base(0);
+	ioport_resource.start = 0;
+	ioport_resource.end = ~0;
+
+	/* intended to somewhat resemble ARM; see Documentation/arm/booting.rst */
+	if (fw_arg0 == 0 && fw_arg1 == 0xffffffff)
+		dtb = phys_to_virt(fw_arg2);
+	else
+		dtb = get_fdt();
+
+	if (!dtb)
+		cfe_die("no dtb found");
+
+	__dt_setup_arch(dtb);
+
+	for (q = bmips_quirk_list; q->quirk_fn; q++) {
+		if (of_flat_dt_is_compatible(of_get_flat_dt_root(),
+					     q->compatible)) {
+			q->quirk_fn();
+		}
+	}
+}
+
+void __init device_tree_init(void)
+{
+	struct device_node *np;
+
+	unflatten_and_copy_device_tree();
+
+	/* Disable SMP boot unless both CPUs are listed in DT and !disabled */
+	np = of_find_node_by_name(NULL, "cpus");
+	if (np && of_get_available_child_count(np) <= 1)
+		bmips_smp_enabled = 0;
+	of_node_put(np);
+}
+
+static int __init plat_dev_init(void)
+{
+	of_clk_init(NULL);
+	return 0;
+}
+
+arch_initcall(plat_dev_init);
diff --git a/arch/mips/boot/.gitignore b/arch/mips/boot/.gitignore
new file mode 100644
index 000000000..1c7adddf2
--- /dev/null
+++ b/arch/mips/boot/.gitignore
@@ -0,0 +1,9 @@
+# SPDX-License-Identifier: GPL-2.0-only
+mkboot
+elf2ecoff
+vmlinux.*
+vmlinuz.*
+zImage
+zImage.tmp
+calc_vmlinuz_load_addr
+uImage
diff --git a/arch/mips/boot/Makefile b/arch/mips/boot/Makefile
new file mode 100644
index 000000000..196c44fa7
--- /dev/null
+++ b/arch/mips/boot/Makefile
@@ -0,0 +1,176 @@
+#
+# This file is subject to the terms and conditions of the GNU General Public
+# License.  See the file "COPYING" in the main directory of this archive
+# for more details.
+#
+# Copyright (C) 1995, 1998, 2001, 2002 by Ralf Baechle
+# Copyright (C) 2004  Maciej W. Rozycki
+#
+
+#
+# Some DECstations need all possible sections of an ECOFF executable
+#
+ifdef CONFIG_MACH_DECSTATION
+  e2eflag := -a
+endif
+
+#
+# Drop some uninteresting sections in the kernel.
+# This is only relevant for ELF kernels but doesn't hurt a.out
+#
+drop-sections := .reginfo .mdebug .comment .note .pdr .options .MIPS.options
+strip-flags   := $(addprefix --remove-section=,$(drop-sections))
+
+hostprogs := elf2ecoff
+
+suffix-y			:= bin
+suffix-$(CONFIG_KERNEL_BZIP2)	:= bz2
+suffix-$(CONFIG_KERNEL_GZIP)	:= gz
+suffix-$(CONFIG_KERNEL_LZMA)	:= lzma
+suffix-$(CONFIG_KERNEL_LZO)	:= lzo
+
+targets := vmlinux.ecoff
+quiet_cmd_ecoff = ECOFF	  $@
+      cmd_ecoff = $(obj)/elf2ecoff $(VMLINUX) $@ $(e2eflag)
+$(obj)/vmlinux.ecoff: $(obj)/elf2ecoff $(VMLINUX) FORCE
+	$(call if_changed,ecoff)
+
+targets += vmlinux.bin
+quiet_cmd_bin = OBJCOPY $@
+      cmd_bin = $(OBJCOPY) -O binary $(strip-flags) $(VMLINUX) $@
+$(obj)/vmlinux.bin: $(VMLINUX) FORCE
+	$(call if_changed,bin)
+
+targets += vmlinux.srec
+quiet_cmd_srec = OBJCOPY $@
+      cmd_srec = $(OBJCOPY) -S -O srec $(strip-flags) $(VMLINUX) $@
+$(obj)/vmlinux.srec: $(VMLINUX) FORCE
+	$(call if_changed,srec)
+
+UIMAGE_LOADADDR  = $(VMLINUX_LOAD_ADDRESS)
+UIMAGE_ENTRYADDR = $(VMLINUX_ENTRY_ADDRESS)
+
+#
+# Compressed vmlinux images
+#
+
+extra-y += vmlinux.bin.bz2
+extra-y += vmlinux.bin.gz
+extra-y += vmlinux.bin.lzma
+extra-y += vmlinux.bin.lzo
+
+$(obj)/vmlinux.bin.bz2: $(obj)/vmlinux.bin FORCE
+	$(call if_changed,bzip2)
+
+$(obj)/vmlinux.bin.gz: $(obj)/vmlinux.bin FORCE
+	$(call if_changed,gzip)
+
+$(obj)/vmlinux.bin.lzma: $(obj)/vmlinux.bin FORCE
+	$(call if_changed,lzma)
+
+$(obj)/vmlinux.bin.lzo: $(obj)/vmlinux.bin FORCE
+	$(call if_changed,lzo)
+
+#
+# Compressed u-boot images
+#
+
+targets += uImage
+targets += uImage.bin
+targets += uImage.bz2
+targets += uImage.gz
+targets += uImage.lzma
+targets += uImage.lzo
+
+$(obj)/uImage.bin: $(obj)/vmlinux.bin FORCE
+	$(call if_changed,uimage,none)
+
+$(obj)/uImage.bz2: $(obj)/vmlinux.bin.bz2 FORCE
+	$(call if_changed,uimage,bzip2)
+
+$(obj)/uImage.gz: $(obj)/vmlinux.bin.gz FORCE
+	$(call if_changed,uimage,gzip)
+
+$(obj)/uImage.lzma: $(obj)/vmlinux.bin.lzma FORCE
+	$(call if_changed,uimage,lzma)
+
+$(obj)/uImage.lzo: $(obj)/vmlinux.bin.lzo FORCE
+	$(call if_changed,uimage,lzo)
+
+$(obj)/uImage: $(obj)/uImage.$(suffix-y)
+	@ln -sf $(notdir $<) $@
+	@echo '  Image $@ is ready'
+
+#
+# Flattened Image Tree (.itb) images
+#
+
+ifeq ($(ADDR_BITS),32)
+itb_addr_cells = 1
+endif
+ifeq ($(ADDR_BITS),64)
+itb_addr_cells = 2
+endif
+
+targets += vmlinux.its.S
+
+quiet_cmd_its_cat = CAT     $@
+      cmd_its_cat = cat $(real-prereqs) >$@
+
+$(obj)/vmlinux.its.S: $(addprefix $(srctree)/arch/mips/$(PLATFORM)/,$(ITS_INPUTS)) FORCE
+	$(call if_changed,its_cat)
+
+targets += vmlinux.its
+targets += vmlinux.gz.its
+targets += vmlinux.bz2.its
+targets += vmlinux.lzma.its
+targets += vmlinux.lzo.its
+
+quiet_cmd_cpp_its_S = ITS     $@
+      cmd_cpp_its_S = $(CPP) -P -C -o $@ $< \
+		        -DKERNEL_NAME="\"Linux $(KERNELRELEASE)\"" \
+			-DVMLINUX_BINARY="\"$(3)\"" \
+			-DVMLINUX_COMPRESSION="\"$(2)\"" \
+			-DVMLINUX_LOAD_ADDRESS=$(VMLINUX_LOAD_ADDRESS) \
+			-DVMLINUX_ENTRY_ADDRESS=$(VMLINUX_ENTRY_ADDRESS) \
+			-DADDR_BITS=$(ADDR_BITS) \
+			-DADDR_CELLS=$(itb_addr_cells)
+
+$(obj)/vmlinux.its: $(obj)/vmlinux.its.S $(VMLINUX) FORCE
+	$(call if_changed,cpp_its_S,none,vmlinux.bin)
+
+$(obj)/vmlinux.gz.its: $(obj)/vmlinux.its.S $(VMLINUX) FORCE
+	$(call if_changed,cpp_its_S,gzip,vmlinux.bin.gz)
+
+$(obj)/vmlinux.bz2.its: $(obj)/vmlinux.its.S $(VMLINUX)  FORCE
+	$(call if_changed,cpp_its_S,bzip2,vmlinux.bin.bz2)
+
+$(obj)/vmlinux.lzma.its: $(obj)/vmlinux.its.S $(VMLINUX) FORCE
+	$(call if_changed,cpp_its_S,lzma,vmlinux.bin.lzma)
+
+$(obj)/vmlinux.lzo.its: $(obj)/vmlinux.its.S $(VMLINUX) FORCE
+	$(call if_changed,cpp_its_S,lzo,vmlinux.bin.lzo)
+
+targets += vmlinux.itb
+targets += vmlinux.gz.itb
+targets += vmlinux.bz2.itb
+targets += vmlinux.lzma.itb
+targets += vmlinux.lzo.itb
+
+quiet_cmd_itb-image = ITB     $@
+      cmd_itb-image = \
+		env PATH="$(objtree)/scripts/dtc:$(PATH)" \
+		$(BASH) $(MKIMAGE) \
+		-D "-I dts -O dtb -p 500 \
+			--include $(objtree)/arch/mips \
+			--warning no-unit_address_vs_reg" \
+		-f $(2) $@
+
+$(obj)/vmlinux.itb: $(obj)/vmlinux.its $(obj)/vmlinux.bin FORCE
+	$(call if_changed,itb-image,$<)
+
+$(obj)/vmlinux.%.itb: $(obj)/vmlinux.%.its $(obj)/vmlinux.bin.% FORCE
+	$(call if_changed,itb-image,$<)
+
+# for cleaning
+subdir- += compressed tools
diff --git a/arch/mips/boot/compressed/Makefile b/arch/mips/boot/compressed/Makefile
new file mode 100644
index 000000000..6cc28173b
--- /dev/null
+++ b/arch/mips/boot/compressed/Makefile
@@ -0,0 +1,219 @@
+#
+# This file is subject to the terms and conditions of the GNU General Public
+# License.
+#
+# Adapted for MIPS Pete Popov, Dan Malek
+#
+# Copyright (C) 1994 by Linus Torvalds
+# Adapted for PowerPC by Gary Thomas
+# modified by Cort (cort@cs.nmt.edu)
+#
+# Copyright (C) 2009 Lemote Inc. & DSLab, Lanzhou University
+# Author: Wu Zhangjin <wuzhangjin@gmail.com>
+#
+
+include $(srctree)/arch/mips/Kbuild.platforms
+
+# set the default size of the mallocing area for decompressing
+BOOT_HEAP_SIZE := 0x400000
+
+# Disable Function Tracer
+KBUILD_CFLAGS := $(filter-out $(CC_FLAGS_FTRACE), $(KBUILD_CFLAGS))
+
+KBUILD_CFLAGS := $(filter-out -fstack-protector, $(KBUILD_CFLAGS))
+
+# Disable lq/sq in zboot
+ifdef CONFIG_CPU_LOONGSON64
+KBUILD_CFLAGS := $(filter-out -march=loongson3a, $(KBUILD_CFLAGS)) -march=mips64r2
+endif
+
+KBUILD_CFLAGS := $(KBUILD_CFLAGS) -D__KERNEL__ -D__DISABLE_EXPORTS \
+	-DBOOT_HEAP_SIZE=$(BOOT_HEAP_SIZE) -D"VMLINUX_LOAD_ADDRESS_ULL=$(VMLINUX_LOAD_ADDRESS)ull"
+
+KBUILD_AFLAGS := $(KBUILD_AFLAGS) -D__ASSEMBLY__ \
+	-DBOOT_HEAP_SIZE=$(BOOT_HEAP_SIZE) \
+	-DKERNEL_ENTRY=$(VMLINUX_ENTRY_ADDRESS)
+
+# Prevents link failures: __sanitizer_cov_trace_pc() is not linked in.
+KCOV_INSTRUMENT		:= n
+GCOV_PROFILE := n
+UBSAN_SANITIZE := n
+KCSAN_SANITIZE			:= n
+
+# decompressor objects (linked with vmlinuz)
+vmlinuzobjs-y := $(obj)/head.o $(obj)/decompress.o $(obj)/string.o $(obj)/bswapsi.o
+
+ifdef CONFIG_DEBUG_ZBOOT
+vmlinuzobjs-$(CONFIG_DEBUG_ZBOOT)		   += $(obj)/dbg.o
+vmlinuzobjs-$(CONFIG_SYS_SUPPORTS_ZBOOT_UART16550) += $(obj)/uart-16550.o
+vmlinuzobjs-$(CONFIG_SYS_SUPPORTS_ZBOOT_UART_PROM) += $(obj)/uart-prom.o
+vmlinuzobjs-$(CONFIG_MIPS_ALCHEMY)		   += $(obj)/uart-alchemy.o
+vmlinuzobjs-$(CONFIG_ATH79)			   += $(obj)/uart-ath79.o
+endif
+
+vmlinuzobjs-$(CONFIG_KERNEL_XZ) += $(obj)/ashldi3.o
+
+vmlinuzobjs-$(CONFIG_KERNEL_ZSTD) += $(obj)/bswapdi.o $(obj)/ashldi3.o $(obj)/clz_ctz.o
+
+targets := $(notdir $(vmlinuzobjs-y))
+
+targets += vmlinux.bin
+
+OBJCOPYFLAGS_vmlinux.bin := $(OBJCOPYFLAGS) -O binary -R .comment -S
+
+$(obj)/vmlinux.bin: $(KBUILD_IMAGE) FORCE
+	$(call if_changed,objcopy)
+
+tool_$(CONFIG_KERNEL_GZIP)    = gzip
+tool_$(CONFIG_KERNEL_BZIP2)   = bzip2_with_size
+tool_$(CONFIG_KERNEL_LZ4)     = lz4_with_size
+tool_$(CONFIG_KERNEL_LZMA)    = lzma_with_size
+tool_$(CONFIG_KERNEL_LZO)     = lzo_with_size
+tool_$(CONFIG_KERNEL_XZ)      = xzkern_with_size
+tool_$(CONFIG_KERNEL_ZSTD)    = zstd22_with_size
+
+targets += vmlinux.bin.z
+
+$(obj)/vmlinux.bin.z: $(obj)/vmlinux.bin FORCE
+	$(call if_changed,$(tool_y))
+
+targets += piggy.o dummy.o
+
+OBJCOPYFLAGS_piggy.o := --add-section=.image=$(obj)/vmlinux.bin.z \
+			--set-section-flags=.image=contents,alloc,load,readonly,data
+
+$(obj)/piggy.o: $(obj)/dummy.o $(obj)/vmlinux.bin.z FORCE
+	$(call if_changed,objcopy)
+
+HOSTCFLAGS_calc_vmlinuz_load_addr.o += $(LINUXINCLUDE)
+
+# Calculate the load address of the compressed kernel image
+hostprogs := calc_vmlinuz_load_addr
+
+ifneq (0x0,$(CONFIG_ZBOOT_LOAD_ADDRESS))
+zload-y	= $(CONFIG_ZBOOT_LOAD_ADDRESS)
+endif
+
+ifneq ($(zload-y),)
+VMLINUZ_LOAD_ADDRESS := $(zload-y)
+else
+VMLINUZ_LOAD_ADDRESS = $(shell $(obj)/calc_vmlinuz_load_addr \
+		$(obj)/vmlinux.bin $(LINKER_LOAD_ADDRESS))
+endif
+UIMAGE_LOADADDR = $(VMLINUZ_LOAD_ADDRESS)
+
+vmlinuzobjs-y += $(obj)/piggy.o
+
+targets += ../../../../vmlinuz
+
+quiet_cmd_zld = LD      $@
+      cmd_zld = $(LD) $(KBUILD_LDFLAGS) -Ttext $(VMLINUZ_LOAD_ADDRESS) -T $< $(vmlinuzobjs-y) -o $@
+quiet_cmd_strip = STRIP   $@
+      cmd_strip = $(STRIP) -s $@
+
+$(objtree)/vmlinuz: $(src)/ld.script $(vmlinuzobjs-y) $(obj)/calc_vmlinuz_load_addr
+	$(call cmd,zld)
+	$(call cmd,strip)
+
+objboot := $(objtree)/arch/mips/boot
+
+$(objboot)/vmlinuz: $(objtree)/vmlinuz FORCE
+
+#
+# Some DECstations need all possible sections of an ECOFF executable
+#
+ifdef CONFIG_MACH_DECSTATION
+  e2eflag := -a
+endif
+
+# elf2ecoff can only handle 32bit image
+hostprogs += ../elf2ecoff
+
+ifdef CONFIG_32BIT
+	VMLINUZ = $(objtree)/vmlinuz
+else
+	VMLINUZ = $(objboot)/vmlinuz.32
+endif
+
+targets += ../vmlinuz.32
+
+quiet_cmd_32 = OBJCOPY $@
+      cmd_32 = $(OBJCOPY) -O $(32bit-bfd) $(OBJCOPYFLAGS) $< $@
+
+$(objboot)/vmlinuz.32: $(objtree)/vmlinuz
+	$(call cmd,32)
+
+targets += ../vmlinuz.ecoff
+
+quiet_cmd_ecoff = ECOFF	  $@
+      cmd_ecoff = $< $(VMLINUZ) $@ $(e2eflag)
+
+$(objboot)/vmlinuz.ecoff: $(objboot)/elf2ecoff $(VMLINUZ)
+	$(call cmd,ecoff)
+
+targets += ../vmlinuz.bin
+
+OBJCOPYFLAGS_vmlinuz.bin := $(OBJCOPYFLAGS) -O binary
+
+$(objboot)/vmlinuz.bin: $(objtree)/vmlinuz
+	$(call cmd,objcopy)
+
+targets += ../vmlinuz.srec
+
+OBJCOPYFLAGS_vmlinuz.srec := $(OBJCOPYFLAGS) -S -O srec
+
+$(objboot)/vmlinuz.srec: $(objtree)/vmlinuz
+	$(call cmd,objcopy)
+
+targets += ../uzImage.bin
+
+$(objboot)/uzImage.bin: $(objboot)/vmlinuz.bin FORCE
+	$(call if_changed,uimage,none)
+
+#
+# Flattened Image Tree (.itb) image
+#
+
+ifeq ($(ADDR_BITS),32)
+itb_addr_cells = 1
+endif
+ifeq ($(ADDR_BITS),64)
+itb_addr_cells = 2
+endif
+
+targets += ../vmlinuz.its.S
+
+quiet_cmd_its_cat = CAT     $@
+      cmd_its_cat = cat $(real-prereqs) >$@
+
+$(objboot)/vmlinuz.its.S: $(addprefix $(srctree)/arch/mips/$(PLATFORM)/,$(ITS_INPUTS)) FORCE
+	$(call if_changed,its_cat)
+
+targets += ../vmlinuz.its
+
+quiet_cmd_cpp_its_S = ITS     $@
+      cmd_cpp_its_S = $(CPP) -P -C -o $@ $< \
+		        -DKERNEL_NAME="\"Linux $(KERNELRELEASE)\"" \
+			-DVMLINUX_BINARY="\"$(2)\"" \
+			-DVMLINUX_COMPRESSION="\"none\"" \
+			-DVMLINUX_LOAD_ADDRESS=$(VMLINUZ_LOAD_ADDRESS) \
+			-DVMLINUX_ENTRY_ADDRESS=$(VMLINUZ_LOAD_ADDRESS) \
+			-DADDR_BITS=$(ADDR_BITS) \
+			-DADDR_CELLS=$(itb_addr_cells)
+
+$(objboot)/vmlinuz.its: $(objboot)/vmlinuz.its.S FORCE
+	$(call if_changed,cpp_its_S,vmlinuz.bin)
+
+targets += ../vmlinuz.itb
+
+quiet_cmd_itb-image = ITB     $@
+      cmd_itb-image = \
+		env PATH="$(objtree)/scripts/dtc:$(PATH)" \
+		$(BASH) $(MKIMAGE) \
+		-D "-I dts -O dtb -p 500 \
+			--include $(objtree)/arch/mips \
+			--warning no-unit_address_vs_reg" \
+		-f $(2) $@
+
+$(objboot)/vmlinuz.itb: $(objboot)/vmlinuz.its $(objboot)/vmlinuz.bin FORCE
+	$(call if_changed,itb-image,$<)
diff --git a/arch/mips/boot/compressed/ashldi3.c b/arch/mips/boot/compressed/ashldi3.c
new file mode 100644
index 000000000..f7bf6a7aa
--- /dev/null
+++ b/arch/mips/boot/compressed/ashldi3.c
@@ -0,0 +1,2 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include "../../../../lib/ashldi3.c"
diff --git a/arch/mips/boot/compressed/bswapdi.c b/arch/mips/boot/compressed/bswapdi.c
new file mode 100644
index 000000000..acb28aebb
--- /dev/null
+++ b/arch/mips/boot/compressed/bswapdi.c
@@ -0,0 +1,2 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include "../../lib/bswapdi.c"
diff --git a/arch/mips/boot/compressed/bswapsi.c b/arch/mips/boot/compressed/bswapsi.c
new file mode 100644
index 000000000..fdb9c6476
--- /dev/null
+++ b/arch/mips/boot/compressed/bswapsi.c
@@ -0,0 +1,2 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include "../../lib/bswapsi.c"
diff --git a/arch/mips/boot/compressed/calc_vmlinuz_load_addr.c b/arch/mips/boot/compressed/calc_vmlinuz_load_addr.c
new file mode 100644
index 000000000..080b926d2
--- /dev/null
+++ b/arch/mips/boot/compressed/calc_vmlinuz_load_addr.c
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2010 "Wu Zhangjin" <wuzhangjin@gmail.com>
+ */
+
+#include <sys/types.h>
+#include <sys/stat.h>
+#include <errno.h>
+#include <stdint.h>
+#include <stdio.h>
+#include <stdlib.h>
+#include <linux/sizes.h>
+
+int main(int argc, char *argv[])
+{
+	unsigned long long vmlinux_size, vmlinux_load_addr, vmlinuz_load_addr;
+	struct stat sb;
+
+	if (argc != 3) {
+		fprintf(stderr, "Usage: %s <pathname> <vmlinux_load_addr>\n",
+				argv[0]);
+		return EXIT_FAILURE;
+	}
+
+	if (stat(argv[1], &sb) == -1) {
+		perror("stat");
+		return EXIT_FAILURE;
+	}
+
+	/* Convert hex characters to dec number */
+	errno = 0;
+	if (sscanf(argv[2], "%llx", &vmlinux_load_addr) != 1) {
+		if (errno != 0)
+			perror("sscanf");
+		else
+			fprintf(stderr, "No matching characters\n");
+
+		return EXIT_FAILURE;
+	}
+
+	vmlinux_size = (uint64_t)sb.st_size;
+	vmlinuz_load_addr = vmlinux_load_addr + vmlinux_size;
+
+	/*
+	 * Align with 64KB: KEXEC needs load sections to be aligned to PAGE_SIZE,
+	 * which may be as large as 64KB depending on the kernel configuration.
+	 */
+
+	vmlinuz_load_addr += (SZ_64K - vmlinux_size % SZ_64K);
+
+	printf("0x%llx\n", vmlinuz_load_addr);
+
+	return EXIT_SUCCESS;
+}
diff --git a/arch/mips/boot/compressed/clz_ctz.c b/arch/mips/boot/compressed/clz_ctz.c
new file mode 100644
index 000000000..b4a1b6eb2
--- /dev/null
+++ b/arch/mips/boot/compressed/clz_ctz.c
@@ -0,0 +1,2 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include "../../../../lib/clz_ctz.c"
diff --git a/arch/mips/boot/compressed/dbg.c b/arch/mips/boot/compressed/dbg.c
new file mode 100644
index 000000000..f6728a8fd
--- /dev/null
+++ b/arch/mips/boot/compressed/dbg.c
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * MIPS-specific debug support for pre-boot environment
+ *
+ * NOTE: putc() is board specific, if your board have a 16550 compatible uart,
+ * please select SYS_SUPPORTS_ZBOOT_UART16550 for your machine. othewise, you
+ * need to implement your own putc().
+ */
+#include <linux/compiler.h>
+#include <linux/types.h>
+
+void __weak putc(char c)
+{
+}
+
+void puts(const char *s)
+{
+	char c;
+	while ((c = *s++) != '\0') {
+		putc(c);
+		if (c == '\n')
+			putc('\r');
+	}
+}
+
+void puthex(unsigned long long val)
+{
+
+	unsigned char buf[10];
+	int i;
+	for (i = 7; i >= 0; i--) {
+		buf[i] = "0123456789ABCDEF"[val & 0x0F];
+		val >>= 4;
+	}
+	buf[8] = '\0';
+	puts(buf);
+}
diff --git a/arch/mips/boot/compressed/decompress.c b/arch/mips/boot/compressed/decompress.c
new file mode 100644
index 000000000..c5dd41525
--- /dev/null
+++ b/arch/mips/boot/compressed/decompress.c
@@ -0,0 +1,141 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2001 MontaVista Software Inc.
+ * Author: Matt Porter <mporter@mvista.com>
+ *
+ * Copyright (C) 2009 Lemote, Inc.
+ * Author: Wu Zhangjin <wuzhangjin@gmail.com>
+ */
+
+#define DISABLE_BRANCH_PROFILING
+
+#define __NO_FORTIFY
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <linux/libfdt.h>
+
+#include <asm/addrspace.h>
+#include <asm/unaligned.h>
+#include <asm-generic/vmlinux.lds.h>
+
+/*
+ * These two variables specify the free mem region
+ * that can be used for temporary malloc area
+ */
+unsigned long free_mem_ptr;
+unsigned long free_mem_end_ptr;
+
+/* The linker tells us where the image is. */
+extern unsigned char __image_begin[], __image_end[];
+
+/* debug interfaces  */
+#ifdef CONFIG_DEBUG_ZBOOT
+extern void puts(const char *s);
+extern void puthex(unsigned long long val);
+#else
+#define puts(s) do {} while (0)
+#define puthex(val) do {} while (0)
+#endif
+
+extern char __appended_dtb[];
+
+void error(char *x)
+{
+	puts("\n\n");
+	puts(x);
+	puts("\n\n -- System halted");
+
+	while (1)
+		;	/* Halt */
+}
+
+/* activate the code for pre-boot environment */
+#define STATIC static
+
+#ifdef CONFIG_KERNEL_GZIP
+#include "../../../../lib/decompress_inflate.c"
+#endif
+
+#ifdef CONFIG_KERNEL_BZIP2
+#include "../../../../lib/decompress_bunzip2.c"
+#endif
+
+#ifdef CONFIG_KERNEL_LZ4
+#include "../../../../lib/decompress_unlz4.c"
+#endif
+
+#ifdef CONFIG_KERNEL_LZMA
+#include "../../../../lib/decompress_unlzma.c"
+#endif
+
+#ifdef CONFIG_KERNEL_LZO
+#include "../../../../lib/decompress_unlzo.c"
+#endif
+
+#ifdef CONFIG_KERNEL_XZ
+#include "../../../../lib/decompress_unxz.c"
+#endif
+
+#ifdef CONFIG_KERNEL_ZSTD
+#include "../../../../lib/decompress_unzstd.c"
+#endif
+
+const unsigned long __stack_chk_guard = 0x000a0dff;
+
+void __stack_chk_fail(void)
+{
+	error("stack-protector: Kernel stack is corrupted\n");
+}
+
+void decompress_kernel(unsigned long boot_heap_start)
+{
+	unsigned long zimage_start, zimage_size;
+
+	zimage_start = (unsigned long)(__image_begin);
+	zimage_size = (unsigned long)(__image_end) -
+	    (unsigned long)(__image_begin);
+
+	puts("zimage at:     ");
+	puthex(zimage_start);
+	puts(" ");
+	puthex(zimage_size + zimage_start);
+	puts("\n");
+
+	/* This area are prepared for mallocing when decompressing */
+	free_mem_ptr = boot_heap_start;
+	free_mem_end_ptr = boot_heap_start + BOOT_HEAP_SIZE;
+
+	/* Display standard Linux/MIPS boot prompt */
+	puts("Uncompressing Linux at load address ");
+	puthex(VMLINUX_LOAD_ADDRESS_ULL);
+	puts("\n");
+
+	/* Decompress the kernel with according algorithm */
+	__decompress((char *)zimage_start, zimage_size, 0, 0,
+		   (void *)VMLINUX_LOAD_ADDRESS_ULL, 0, 0, error);
+
+	if (IS_ENABLED(CONFIG_MIPS_RAW_APPENDED_DTB) &&
+	    fdt_magic((void *)&__appended_dtb) == FDT_MAGIC) {
+		unsigned int image_size, dtb_size;
+
+		dtb_size = fdt_totalsize((void *)&__appended_dtb);
+
+		/* last four bytes is always image size in little endian */
+		image_size = get_unaligned_le32((void *)__image_end - 4);
+
+		/* The device tree's address must be properly aligned  */
+		image_size = ALIGN(image_size, STRUCT_ALIGNMENT);
+
+		puts("Copy device tree to address  ");
+		puthex(VMLINUX_LOAD_ADDRESS_ULL + image_size);
+		puts("\n");
+
+		/* copy dtb to where the booted kernel will expect it */
+		memcpy((void *)VMLINUX_LOAD_ADDRESS_ULL + image_size,
+		       __appended_dtb, dtb_size);
+	}
+
+	/* FIXME: should we flush cache here? */
+	puts("Now, booting the kernel...\n");
+}
diff --git a/arch/mips/boot/compressed/dummy.c b/arch/mips/boot/compressed/dummy.c
new file mode 100644
index 000000000..31dbf45bf
--- /dev/null
+++ b/arch/mips/boot/compressed/dummy.c
@@ -0,0 +1,4 @@
+int main(void)
+{
+	return 0;
+}
diff --git a/arch/mips/boot/compressed/head.S b/arch/mips/boot/compressed/head.S
new file mode 100644
index 000000000..5795d0af1
--- /dev/null
+++ b/arch/mips/boot/compressed/head.S
@@ -0,0 +1,52 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994, 1995 Waldorf Electronics
+ * Written by Ralf Baechle and Andreas Busse
+ * Copyright (C) 1995 - 1999 Ralf Baechle
+ * Copyright (C) 1996 Paul M. Antoine
+ * Modified for DECStation and hence R3000 support by Paul M. Antoine
+ * Further modifications by David S. Miller and Harald Koerfgen
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ */
+
+#include <asm/asm.h>
+#include <asm/regdef.h>
+
+	LEAF(start)
+	/* Save boot rom start args */
+	move	s0, a0
+	move	s1, a1
+	move	s2, a2
+	move	s3, a3
+
+	/* Clear BSS */
+	PTR_LA	a0, _edata
+	PTR_LA	a2, _end
+1:	sw	zero, 0(a0)
+	addiu	a0, a0, 4
+	bne	a2, a0, 1b
+
+	PTR_LA	a0, (.heap)	     /* heap address */
+	PTR_LA	sp, (.stack + 8192)  /* stack address */
+
+	PTR_LA	t9, decompress_kernel
+	jalr	t9
+
+2:
+	move	a0, s0
+	move	a1, s1
+	move	a2, s2
+	move	a3, s3
+	PTR_LI	t9, KERNEL_ENTRY
+	jalr	t9
+
+3:
+	b	3b
+
+	END(start)
+
+	.comm .heap,BOOT_HEAP_SIZE,4
+	.comm .stack,4096*2,4
diff --git a/arch/mips/boot/compressed/ld.script b/arch/mips/boot/compressed/ld.script
new file mode 100644
index 000000000..0ebb66727
--- /dev/null
+++ b/arch/mips/boot/compressed/ld.script
@@ -0,0 +1,60 @@
+/*
+ * ld.script for compressed kernel support of MIPS
+ *
+ * Copyright (C) 2009 Lemote Inc.
+ * Author: Wu Zhangjin <wuzhanjing@gmail.com>
+ * Copyright (C) 2010 "Wu Zhangjin" <wuzhanjing@gmail.com>
+ */
+
+OUTPUT_ARCH(mips)
+ENTRY(start)
+PHDRS {
+	text PT_LOAD FLAGS(7); /* RWX */
+}
+SECTIONS
+{
+	/* Text and read-only data */
+	/* . = VMLINUZ_LOAD_ADDRESS; */
+	.text : {
+		*(.text)
+		*(.rodata)
+	}: text
+	/* End of text section */
+
+	/* Writable data */
+	.data : {
+		*(.data)
+		/* Put the compressed image here */
+		__image_begin = .;
+		*(.image)
+		__image_end = .;
+		CONSTRUCTORS
+		. = ALIGN(16);
+	}
+
+	.appended_dtb : {
+		__appended_dtb = .;
+		/* leave space for appended DTB */
+		. += 0x100000;
+	}
+
+	_edata = .;
+	/* End of data section */
+
+	/* BSS */
+	.bss : {
+		*(.bss)
+	}
+	. = ALIGN(16);
+	_end = .;
+
+	/* Sections to be discarded */
+	/DISCARD/ : {
+		*(.MIPS.options)
+		*(.options)
+		*(.pdr)
+		*(.reginfo)
+		*(.comment)
+		*(.note)
+	}
+}
diff --git a/arch/mips/boot/compressed/string.c b/arch/mips/boot/compressed/string.c
new file mode 100644
index 000000000..0b593b709
--- /dev/null
+++ b/arch/mips/boot/compressed/string.c
@@ -0,0 +1,46 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * arch/mips/boot/compressed/string.c
+ *
+ * Very small subset of simple string routines
+ */
+
+#include <linux/compiler_attributes.h>
+#include <linux/types.h>
+
+void *memcpy(void *dest, const void *src, size_t n)
+{
+	int i;
+	const char *s = src;
+	char *d = dest;
+
+	for (i = 0; i < n; i++)
+		d[i] = s[i];
+	return dest;
+}
+
+void *memset(void *s, int c, size_t n)
+{
+	int i;
+	char *ss = s;
+
+	for (i = 0; i < n; i++)
+		ss[i] = c;
+	return s;
+}
+
+void * __weak memmove(void *dest, const void *src, size_t n)
+{
+	unsigned int i;
+	const char *s = src;
+	char *d = dest;
+
+	if ((uintptr_t)dest < (uintptr_t)src) {
+		for (i = 0; i < n; i++)
+			d[i] = s[i];
+	} else {
+		for (i = n; i > 0; i--)
+			d[i - 1] = s[i - 1];
+	}
+	return dest;
+}
diff --git a/arch/mips/boot/compressed/uart-16550.c b/arch/mips/boot/compressed/uart-16550.c
new file mode 100644
index 000000000..96d28f211
--- /dev/null
+++ b/arch/mips/boot/compressed/uart-16550.c
@@ -0,0 +1,52 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * 16550 compatible uart based serial debug support for zboot
+ */
+
+#include <linux/types.h>
+#include <linux/serial_reg.h>
+
+#include <asm/addrspace.h>
+
+#if defined(CONFIG_MACH_LOONGSON64) || defined(CONFIG_MIPS_MALTA)
+#define UART_BASE 0x1fd003f8
+#define PORT(offset) (CKSEG1ADDR(UART_BASE) + (offset))
+#endif
+
+#ifdef CONFIG_AR7
+#include <ar7.h>
+#define PORT(offset) (CKSEG1ADDR(AR7_REGS_UART0) + (4 * offset))
+#endif
+
+#ifdef CONFIG_MACH_INGENIC
+#define INGENIC_UART_BASE_ADDR	(0x10030000 + 0x1000 * CONFIG_ZBOOT_INGENIC_UART)
+#define PORT(offset) (CKSEG1ADDR(INGENIC_UART_BASE_ADDR) + (4 * offset))
+#endif
+
+#ifndef IOTYPE
+#define IOTYPE char
+#endif
+
+#ifndef PORT
+#error please define the serial port address for your own machine
+#endif
+
+static inline unsigned int serial_in(int offset)
+{
+	return *((volatile IOTYPE *)PORT(offset)) & 0xFF;
+}
+
+static inline void serial_out(int offset, int value)
+{
+	*((volatile IOTYPE *)PORT(offset)) = value & 0xFF;
+}
+
+void putc(char c)
+{
+	int timeout = 1000000;
+
+	while (((serial_in(UART_LSR) & UART_LSR_THRE) == 0) && (timeout-- > 0))
+		;
+
+	serial_out(UART_TX, c);
+}
diff --git a/arch/mips/boot/compressed/uart-alchemy.c b/arch/mips/boot/compressed/uart-alchemy.c
new file mode 100644
index 000000000..8ec63011e
--- /dev/null
+++ b/arch/mips/boot/compressed/uart-alchemy.c
@@ -0,0 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <asm/mach-au1x00/au1000.h>
+
+void putc(char c)
+{
+	alchemy_uart_putchar(AU1000_UART0_PHYS_ADDR, c);
+}
diff --git a/arch/mips/boot/compressed/uart-ath79.c b/arch/mips/boot/compressed/uart-ath79.c
new file mode 100644
index 000000000..d68682092
--- /dev/null
+++ b/arch/mips/boot/compressed/uart-ath79.c
@@ -0,0 +1,2 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include "../../ath79/early_printk.c"
diff --git a/arch/mips/boot/compressed/uart-prom.c b/arch/mips/boot/compressed/uart-prom.c
new file mode 100644
index 000000000..a8a0a32e0
--- /dev/null
+++ b/arch/mips/boot/compressed/uart-prom.c
@@ -0,0 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <asm/setup.h>
+
+void putc(char c)
+{
+	prom_putchar(c);
+}
diff --git a/arch/mips/boot/dts/Makefile b/arch/mips/boot/dts/Makefile
new file mode 100644
index 000000000..928f38a79
--- /dev/null
+++ b/arch/mips/boot/dts/Makefile
@@ -0,0 +1,19 @@
+# SPDX-License-Identifier: GPL-2.0
+subdir-$(CONFIG_BMIPS_GENERIC)		+= brcm
+subdir-$(CONFIG_CAVIUM_OCTEON_SOC)	+= cavium-octeon
+subdir-$(CONFIG_FIT_IMAGE_FDT_MARDUK)   += img
+subdir-$(CONFIG_FIT_IMAGE_FDT_BOSTON)	+= img
+subdir-$(CONFIG_MACH_INGENIC)		+= ingenic
+subdir-$(CONFIG_LANTIQ)			+= lantiq
+subdir-$(CONFIG_MACH_LOONGSON64)	+= loongson
+subdir-$(CONFIG_SOC_VCOREIII)		+= mscc
+subdir-$(CONFIG_MIPS_MALTA)		+= mti
+subdir-$(CONFIG_LEGACY_BOARD_SEAD3)	+= mti
+subdir-$(CONFIG_FIT_IMAGE_FDT_NI169445)	+= ni
+subdir-$(CONFIG_MACH_PIC32)		+= pic32
+subdir-$(CONFIG_ATH79)			+= qca
+subdir-$(CONFIG_RALINK)			+= ralink
+subdir-$(CONFIG_MACH_REALTEK_RTL)	+= realtek
+subdir-$(CONFIG_FIT_IMAGE_FDT_XILFPGA)	+= xilfpga
+
+obj-$(CONFIG_BUILTIN_DTB)	:= $(addsuffix /, $(subdir-y))
diff --git a/arch/mips/boot/dts/brcm/Makefile b/arch/mips/boot/dts/brcm/Makefile
new file mode 100644
index 000000000..d85f446cc
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/Makefile
@@ -0,0 +1,37 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_DT_BCM93384WVG)		+= bcm93384wvg.dtb
+dtb-$(CONFIG_DT_BCM93384WVG_VIPER)	+= bcm93384wvg_viper.dtb
+dtb-$(CONFIG_DT_BCM96368MVWG)		+= bcm96368mvwg.dtb
+dtb-$(CONFIG_DT_BCM9EJTAGPRB)		+= bcm9ejtagprb.dtb
+dtb-$(CONFIG_DT_BCM97125CBMB)		+= bcm97125cbmb.dtb
+dtb-$(CONFIG_DT_BCM97346DBSMB)		+= bcm97346dbsmb.dtb
+dtb-$(CONFIG_DT_BCM97358SVMB)		+= bcm97358svmb.dtb
+dtb-$(CONFIG_DT_BCM97360SVMB)		+= bcm97360svmb.dtb
+dtb-$(CONFIG_DT_BCM97362SVMB)		+= bcm97362svmb.dtb
+dtb-$(CONFIG_DT_BCM97420C)		+= bcm97420c.dtb
+dtb-$(CONFIG_DT_BCM97425SVMB)		+= bcm97425svmb.dtb
+dtb-$(CONFIG_DT_BCM97435SVMB)		+= bcm97435svmb.dtb
+dtb-$(CONFIG_DT_COMTREND_VR3032U)	+= bcm63268-comtrend-vr-3032u.dtb
+dtb-$(CONFIG_DT_NETGEAR_CVG834G)	+= bcm3368-netgear-cvg834g.dtb
+dtb-$(CONFIG_DT_SFR_NEUFBOX4_SERCOMM)	+= bcm6358-neufbox4-sercomm.dtb
+dtb-$(CONFIG_DT_SFR_NEUFBOX6_SERCOMM)	+= bcm6362-neufbox6-sercomm.dtb
+
+dtb-$(CONFIG_DT_NONE) += \
+	bcm3368-netgear-cvg834g.dtb \
+	bcm6358-neufbox4-sercomm.dtb \
+	bcm6362-neufbox6-sercomm.dtb \
+	bcm63268-comtrend-vr-3032u.dtb \
+	bcm93384wvg.dtb \
+	bcm93384wvg_viper.dtb \
+	bcm96368mvwg.dtb \
+	bcm9ejtagprb.dtb \
+	bcm97125cbmb.dtb \
+	bcm97346dbsmb.dtb \
+	bcm97358svmb.dtb \
+	bcm97360svmb.dtb \
+	bcm97362svmb.dtb \
+	bcm97420c.dtb \
+	bcm97425svmb.dtb \
+	bcm97435svmb.dtb
+
+obj-$(CONFIG_BUILTIN_DTB)	+= $(addsuffix .o, $(dtb-y))
diff --git a/arch/mips/boot/dts/brcm/bcm3368-netgear-cvg834g.dts b/arch/mips/boot/dts/brcm/bcm3368-netgear-cvg834g.dts
new file mode 100644
index 000000000..d702a843c
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm3368-netgear-cvg834g.dts
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "bcm3368.dtsi"
+
+/ {
+	compatible = "netgear,cvg834g", "brcm,bcm3368";
+	model = "NETGEAR CVG834G";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x02000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &uart0;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/mips/boot/dts/brcm/bcm3368.dtsi b/arch/mips/boot/dts/brcm/bcm3368.dtsi
new file mode 100644
index 000000000..883ca8bed
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm3368.dtsi
@@ -0,0 +1,113 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "dt-bindings/clock/bcm3368-clock.h"
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "brcm,bcm3368";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mips-hpt-frequency = <150000000>;
+
+		cpu@0 {
+			compatible = "brcm,bmips4350";
+			device_type = "cpu";
+			reg = <0>;
+		};
+
+		cpu@1 {
+			compatible = "brcm,bmips4350";
+			device_type = "cpu";
+			reg = <1>;
+		};
+	};
+
+	clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <50000000>;
+		};
+	};
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+	};
+
+	cpu_intc: interrupt-controller {
+		#address-cells = <0>;
+		compatible = "mti,cpu-interrupt-controller";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+
+	ubus {
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		compatible = "simple-bus";
+		ranges;
+
+		clkctl: clock-controller@fff8c004 {
+			compatible = "brcm,bcm3368-clocks";
+			reg = <0xfff8c004 0x4>;
+			#clock-cells = <1>;
+		};
+
+		periph_cntl: syscon@fff8c008 {
+			compatible = "syscon";
+			reg = <0xfff8c008 0x4>;
+			native-endian;
+		};
+
+		reboot: syscon-reboot@fff8c008 {
+			compatible = "syscon-reboot";
+			regmap = <&periph_cntl>;
+			offset = <0x0>;
+			mask = <0x1>;
+		};
+
+		periph_intc: interrupt-controller@fff8c00c {
+			compatible = "brcm,bcm6345-l1-intc";
+			reg = <0xfff8c00c 0x8>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&cpu_intc>;
+			interrupts = <2>;
+		};
+
+		uart0: serial@fff8c100 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0xfff8c100 0x18>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <2>;
+
+			clocks = <&periph_clk>;
+			clock-names = "refclk";
+
+			status = "disabled";
+		};
+
+		uart1: serial@fff8c120 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0xfff8c120 0x18>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <3>;
+
+			clocks = <&periph_clk>;
+			clock-names = "refclk";
+
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/brcm/bcm3384_viper.dtsi b/arch/mips/boot/dts/brcm/bcm3384_viper.dtsi
new file mode 100644
index 000000000..eb2a9c6ed
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm3384_viper.dtsi
@@ -0,0 +1,109 @@
+// SPDX-License-Identifier: GPL-2.0
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "brcm,bcm3384-viper", "brcm,bcm33843-viper";
+
+	memory@0 {
+		device_type = "memory";
+
+		/* Typical ranges.  The bootloader should fill these in. */
+		reg = <0x06000000 0x02000000>,
+		      <0x0e000000 0x02000000>;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* 1/2 of the CPU core clock (standard MIPS behavior) */
+		mips-hpt-frequency = <300000000>;
+
+		cpu@0 {
+			compatible = "brcm,bmips4350";
+			device_type = "cpu";
+			reg = <0>;
+		};
+	};
+
+	cpu_intc: cpu_intc {
+		#address-cells = <0>;
+		compatible = "mti,cpu-interrupt-controller";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+
+	clocks {
+		periph_clk: periph_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <54000000>;
+		};
+	};
+
+	aliases {
+		uart0 = &uart0;
+	};
+
+	ubus {
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		compatible = "brcm,ubus", "simple-bus";
+		ranges;
+		/* No dma-ranges on Viper. */
+
+		periph_intc: periph_intc@14e00048 {
+			compatible = "brcm,bcm3380-l2-intc";
+			reg = <0x14e00048 0x4 0x14e0004c 0x4>,
+			      <0x14e00350 0x4 0x14e00354 0x4>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&cpu_intc>;
+			interrupts = <4>;
+		};
+
+		cmips_intc: cmips_intc@151f8048 {
+			compatible = "brcm,bcm3380-l2-intc";
+			reg = <0x151f8048 0x4 0x151f804c 0x4>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <30>;
+			brcm,int-map-mask = <0xffffffff>;
+		};
+
+		uart0: serial@14e00520 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0x14e00520 0x18>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <2>;
+			clocks = <&periph_clk>;
+			status = "disabled";
+		};
+
+		ehci0: usb@15400300 {
+			compatible = "brcm,bcm3384-ehci", "generic-ehci";
+			reg = <0x15400300 0x100>;
+			big-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <41>;
+			status = "disabled";
+		};
+
+		ohci0: usb@15400400 {
+			compatible = "brcm,bcm3384-ohci", "generic-ohci";
+			reg = <0x15400400 0x100>;
+			big-endian;
+			no-big-frame-no;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <40>;
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/brcm/bcm3384_zephyr.dtsi b/arch/mips/boot/dts/brcm/bcm3384_zephyr.dtsi
new file mode 100644
index 000000000..d7ad769a4
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm3384_zephyr.dtsi
@@ -0,0 +1,127 @@
+// SPDX-License-Identifier: GPL-2.0
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "brcm,bcm3384", "brcm,bcm33843";
+
+	memory@0 {
+		device_type = "memory";
+
+		/* Typical range.  The bootloader should fill this in. */
+		reg = <0x0 0x08000000>;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* On BMIPS5000 this is 1/8th of the CPU core clock */
+		mips-hpt-frequency = <100000000>;
+
+		cpu@0 {
+			compatible = "brcm,bmips5000";
+			device_type = "cpu";
+			reg = <0>;
+		};
+
+		cpu@1 {
+			compatible = "brcm,bmips5000";
+			device_type = "cpu";
+			reg = <1>;
+		};
+	};
+
+	cpu_intc: cpu_intc {
+		#address-cells = <0>;
+		compatible = "mti,cpu-interrupt-controller";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+
+	clocks {
+		periph_clk: periph_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <54000000>;
+		};
+	};
+
+	aliases {
+		uart0 = &uart0;
+	};
+
+	ubus {
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		compatible = "brcm,ubus", "simple-bus";
+		ranges;
+		dma-ranges = <0x00000000 0x08000000 0x08000000>,
+			     <0x08000000 0x00000000 0x08000000>;
+
+		periph_intc: periph_intc@14e00038 {
+			compatible = "brcm,bcm3380-l2-intc";
+			reg = <0x14e00038 0x4 0x14e0003c 0x4>,
+			      <0x14e00340 0x4 0x14e00344 0x4>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&cpu_intc>;
+			interrupts = <4>;
+		};
+
+		zmips_intc: zmips_intc@104b0060 {
+			compatible = "brcm,bcm3380-l2-intc";
+			reg = <0x104b0060 0x4 0x104b0064 0x4>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <29>;
+			brcm,int-map-mask = <0xffffffff>;
+		};
+
+		iop_intc: iop_intc@14e00058 {
+			compatible = "brcm,bcm3380-l2-intc";
+			reg = <0x14e00058 0x4 0x14e0005c 0x4>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&cpu_intc>;
+			interrupts = <6>;
+			brcm,int-map-mask = <0xffffffff>;
+		};
+
+		uart0: serial@14e00520 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0x14e00520 0x18>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <2>;
+			clocks = <&periph_clk>;
+			status = "disabled";
+		};
+
+		ehci0: usb@15400300 {
+			compatible = "brcm,bcm3384-ehci", "generic-ehci";
+			reg = <0x15400300 0x100>;
+			big-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <41>;
+			status = "disabled";
+		};
+
+		ohci0: usb@15400400 {
+			compatible = "brcm,bcm3384-ohci", "generic-ohci";
+			reg = <0x15400400 0x100>;
+			big-endian;
+			no-big-frame-no;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <40>;
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/brcm/bcm63268-comtrend-vr-3032u.dts b/arch/mips/boot/dts/brcm/bcm63268-comtrend-vr-3032u.dts
new file mode 100644
index 000000000..b511bc712
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm63268-comtrend-vr-3032u.dts
@@ -0,0 +1,109 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "bcm63268.dtsi"
+
+/ {
+	compatible = "comtrend,vr-3032u", "brcm,bcm63268";
+	model = "Comtrend VR-3032u";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x04000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &uart0;
+	};
+};
+
+&leds0 {
+	status = "okay";
+	brcm,serial-leds;
+	brcm,serial-dat-low;
+	brcm,serial-shift-inv;
+
+	led@0 {
+		reg = <0>;
+		brcm,hardware-controlled;
+		brcm,link-signal-sources = <0>;
+		/* GPHY0 Speed 0 */
+	};
+	led@1 {
+		reg = <1>;
+		brcm,hardware-controlled;
+		brcm,link-signal-sources = <1>;
+		/* GPHY0 Speed 1 */
+	};
+	led@2 {
+		reg = <2>;
+		active-low;
+		label = "vr-3032u:red:inet";
+	};
+	led@3 {
+		reg = <3>;
+		active-low;
+		label = "vr-3032u:green:dsl";
+	};
+	led@4 {
+		reg = <4>;
+		active-low;
+		label = "vr-3032u:green:usb";
+	};
+	led@7 {
+		reg = <7>;
+		active-low;
+		label = "vr-3032u:green:wps";
+	};
+	led@8 {
+		reg = <8>;
+		active-low;
+		label = "vr-3032u:green:inet";
+	};
+	led@9 {
+		reg = <9>;
+		brcm,hardware-controlled;
+		/* EPHY0 Activity */
+	};
+	led@10 {
+		reg = <10>;
+		brcm,hardware-controlled;
+		/* EPHY1 Activity */
+	};
+	led@11 {
+		reg = <11>;
+		brcm,hardware-controlled;
+		/* EPHY2 Activity */
+	};
+	led@12 {
+		reg = <12>;
+		brcm,hardware-controlled;
+		/* GPHY0 Activity */
+	};
+	led@13 {
+		reg = <13>;
+		brcm,hardware-controlled;
+		/* EPHY0 Speed */
+	};
+	led@14 {
+		reg = <14>;
+		brcm,hardware-controlled;
+		/* EPHY1 Speed */
+	};
+	led@15 {
+		reg = <15>;
+		brcm,hardware-controlled;
+		/* EPHY2 Speed */
+	};
+	led@20 {
+		reg = <20>;
+		active-low;
+		label = "vr-3032u:green:power";
+		default-state = "on";
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/mips/boot/dts/brcm/bcm63268.dtsi b/arch/mips/boot/dts/brcm/bcm63268.dtsi
new file mode 100644
index 000000000..8926417a8
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm63268.dtsi
@@ -0,0 +1,268 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "dt-bindings/clock/bcm63268-clock.h"
+#include "dt-bindings/reset/bcm63268-reset.h"
+#include "dt-bindings/soc/bcm63268-pm.h"
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "brcm,bcm63268";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mips-hpt-frequency = <200000000>;
+
+		cpu@0 {
+			compatible = "brcm,bmips4350";
+			device_type = "cpu";
+			reg = <0>;
+		};
+
+		cpu@1 {
+			compatible = "brcm,bmips4350";
+			device_type = "cpu";
+			reg = <1>;
+		};
+	};
+
+	clocks {
+		periph_osc: periph-osc {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <50000000>;
+			clock-output-names = "periph";
+		};
+
+		hsspi_osc: hsspi-osc {
+			compatible = "fixed-clock";
+
+			#clock-cells = <0>;
+
+			clock-frequency = <400000000>;
+			clock-output-names = "hsspi_osc";
+		};
+	};
+
+	aliases {
+		nflash = &nflash;
+		serial0 = &uart0;
+		serial1 = &uart1;
+		spi0 = &lsspi;
+		spi1 = &hsspi;
+	};
+
+	cpu_intc: interrupt-controller {
+		#address-cells = <0>;
+		compatible = "mti,cpu-interrupt-controller";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+
+	ubus {
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		compatible = "simple-bus";
+		ranges;
+
+		periph_clk: clock-controller@10000004 {
+			compatible = "brcm,bcm63268-clocks";
+			reg = <0x10000004 0x4>;
+			#clock-cells = <1>;
+		};
+
+		pll_cntl: syscon@10000008 {
+			compatible = "syscon";
+			reg = <0x10000008 0x4>;
+			native-endian;
+
+			reboot {
+				compatible = "syscon-reboot";
+				offset = <0x0>;
+				mask = <0x1>;
+			};
+		};
+
+		periph_rst: reset-controller@10000010 {
+			compatible = "brcm,bcm6345-reset";
+			reg = <0x10000010 0x4>;
+			#reset-cells = <1>;
+		};
+
+		periph_intc: interrupt-controller@10000020 {
+			compatible = "brcm,bcm6345-l1-intc";
+			reg = <0x10000020 0x20>,
+			      <0x10000040 0x20>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&cpu_intc>;
+			interrupts = <2>, <3>;
+		};
+
+		timer-mfd@10000080 {
+			compatible = "brcm,bcm7038-twd", "simple-mfd", "syscon";
+			reg = <0x10000080 0x30>;
+			ranges = <0x0 0x10000080 0x30>;
+
+			wdt: watchdog@1c {
+				compatible = "brcm,bcm7038-wdt";
+				reg = <0x1c 0xc>;
+
+				clocks = <&periph_osc>;
+				clock-names = "refclk";
+
+				timeout-sec = <30>;
+			};
+		};
+
+		uart0: serial@10000180 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0x10000180 0x18>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <5>;
+
+			clocks = <&periph_osc>;
+			clock-names = "refclk";
+
+			status = "disabled";
+		};
+
+		nflash: nand@10000200 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,nand-bcm6368",
+				     "brcm,brcmnand-v4.0",
+				     "brcm,brcmnand";
+			reg = <0x10000200 0x180>,
+			      <0x10000600 0x200>,
+			      <0x100000b0 0x10>;
+			reg-names = "nand",
+				    "nand-cache",
+				    "nand-int-base";
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <50>;
+
+			clocks = <&periph_clk BCM63268_CLK_NAND>;
+			clock-names = "nand";
+
+			status = "disabled";
+		};
+
+		uart1: serial@100001a0 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0x100001a0 0x18>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <34>;
+
+			clocks = <&periph_osc>;
+			clock-names = "refclk";
+
+			status = "disabled";
+		};
+
+		lsspi: spi@10000800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6358-spi";
+			reg = <0x10000800 0x70c>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <80>;
+
+			clocks = <&periph_clk BCM63268_CLK_SPI>;
+			clock-names = "spi";
+
+			resets = <&periph_rst BCM63268_RST_SPI>;
+
+			status = "disabled";
+		};
+
+		hsspi: spi@10001000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6328-hsspi";
+			reg = <0x10001000 0x600>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <6>;
+
+			clocks = <&periph_clk BCM63268_CLK_HSSPI>,
+				 <&hsspi_osc>;
+			clock-names = "hsspi",
+				      "pll";
+
+			resets = <&periph_rst BCM63268_RST_SPI>;
+
+			status = "disabled";
+		};
+
+		periph_pwr: power-controller@1000184c {
+			compatible = "brcm,bcm6328-power-controller";
+			reg = <0x1000184c 0x4>;
+			#power-domain-cells = <1>;
+		};
+
+		leds0: led-controller@10001900 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6328-leds";
+			reg = <0x10001900 0x24>;
+
+			status = "disabled";
+		};
+
+		ehci: usb@10002500 {
+			compatible = "brcm,bcm63268-ehci", "generic-ehci";
+			reg = <0x10002500 0x100>;
+			big-endian;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <10>;
+
+			phys = <&usbh 0>;
+			phy-names = "usb";
+
+			status = "disabled";
+		};
+
+		ohci: usb@10002600 {
+			compatible = "brcm,bcm63268-ohci", "generic-ohci";
+			reg = <0x10002600 0x100>;
+			big-endian;
+			no-big-frame-no;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <9>;
+
+			phys = <&usbh 0>;
+			phy-names = "usb";
+
+			status = "disabled";
+		};
+
+		usbh: usb-phy@10002700 {
+			compatible = "brcm,bcm63268-usbh-phy";
+			reg = <0x10002700 0x38>;
+			#phy-cells = <1>;
+
+			clocks = <&periph_clk BCM63268_CLK_USBH>;
+			clock-names = "usbh";
+
+			power-domains = <&periph_pwr BCM63268_POWER_DOMAIN_USBH>;
+
+			resets = <&periph_rst BCM63268_RST_USBH>;
+			reset-names = "usbh";
+
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/brcm/bcm6328.dtsi b/arch/mips/boot/dts/brcm/bcm6328.dtsi
new file mode 100644
index 000000000..634618d43
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm6328.dtsi
@@ -0,0 +1,240 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "dt-bindings/clock/bcm6328-clock.h"
+#include "dt-bindings/reset/bcm6328-reset.h"
+#include "dt-bindings/soc/bcm6328-pm.h"
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "brcm,bcm6328";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mips-hpt-frequency = <160000000>;
+
+		cpu@0 {
+			compatible = "brcm,bmips4350";
+			device_type = "cpu";
+			reg = <0>;
+		};
+
+		cpu@1 {
+			compatible = "brcm,bmips4350";
+			device_type = "cpu";
+			reg = <1>;
+		};
+	};
+
+	clocks {
+		periph_osc: periph-osc {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <50000000>;
+			clock-output-names = "periph";
+		};
+
+		hsspi_osc: hsspi-osc {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <133333333>;
+			clock-output-names = "hsspi_osc";
+		};
+	};
+
+	aliases {
+		nflash = &nflash;
+		serial0 = &uart0;
+		serial1 = &uart1;
+		spi1 = &hsspi;
+	};
+
+	cpu_intc: interrupt-controller {
+		#address-cells = <0>;
+		compatible = "mti,cpu-interrupt-controller";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+
+	ubus {
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		compatible = "simple-bus";
+		ranges;
+
+		periph_clk: clock-controller@10000004 {
+			compatible = "brcm,bcm6328-clocks";
+			reg = <0x10000004 0x4>;
+			#clock-cells = <1>;
+		};
+
+		periph_rst: reset-controller@10000010 {
+			compatible = "brcm,bcm6345-reset";
+			reg = <0x10000010 0x4>;
+			#reset-cells = <1>;
+		};
+
+		periph_intc: interrupt-controller@10000020 {
+			compatible = "brcm,bcm6345-l1-intc";
+			reg = <0x10000020 0x10>,
+			      <0x10000030 0x10>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&cpu_intc>;
+			interrupts = <2>, <3>;
+		};
+
+		wdt: watchdog@1000005c {
+			compatible = "brcm,bcm7038-wdt";
+			reg = <0x1000005c 0xc>;
+
+			clocks = <&periph_osc>;
+			clock-names = "refclk";
+
+			timeout-sec = <30>;
+		};
+
+		soft_reset: syscon@10000068 {
+			compatible = "syscon";
+			reg = <0x10000068 0x4>;
+			native-endian;
+
+			reboot {
+				compatible = "syscon-reboot";
+				offset = <0x0>;
+				mask = <0x1>;
+			};
+		};
+
+		uart0: serial@10000100 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0x10000100 0x18>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <28>;
+
+			clocks = <&periph_osc>;
+			clock-names = "refclk";
+
+			status = "disabled";
+		};
+
+		uart1: serial@10000120 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0x10000120 0x18>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <39>;
+
+			clocks = <&periph_osc>;
+			clock-names = "refclk";
+
+			status = "disabled";
+		};
+
+		nflash: nand@10000200 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,nand-bcm6368",
+				     "brcm,brcmnand-v2.2",
+				     "brcm,brcmnand";
+			reg = <0x10000200 0x180>,
+			      <0x10000400 0x200>,
+			      <0x10000070 0x10>;
+			reg-names = "nand",
+				    "nand-cache",
+				    "nand-int-base";
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <0>;
+
+			status = "disabled";
+		};
+
+		leds0: led-controller@10000800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6328-leds";
+			reg = <0x10000800 0x24>;
+
+			status = "disabled";
+		};
+
+		hsspi: spi@10001000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6328-hsspi";
+			reg = <0x10001000 0x600>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <29>;
+
+			clocks = <&periph_clk BCM6328_CLK_HSSPI>,
+				 <&hsspi_osc>;
+			clock-names = "hsspi",
+				      "pll";
+
+			resets = <&periph_rst BCM6328_RST_SPI>;
+			reset-names = "hsspi";
+
+			status = "disabled";
+		};
+
+		periph_pwr: power-controller@10001848 {
+			compatible = "brcm,bcm6328-power-controller";
+			reg = <0x10001848 0x4>;
+			#power-domain-cells = <1>;
+		};
+
+		ehci: usb@10002500 {
+			compatible = "brcm,bcm6328-ehci", "generic-ehci";
+			reg = <0x10002500 0x100>;
+			big-endian;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <42>;
+
+			phys = <&usbh 0>;
+			phy-names = "usb";
+
+			status = "disabled";
+		};
+
+		ohci: usb@10002600 {
+			compatible = "brcm,bcm6328-ohci", "generic-ohci";
+			reg = <0x10002600 0x100>;
+			big-endian;
+			no-big-frame-no;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <41>;
+
+			phys = <&usbh 0>;
+			phy-names = "usb";
+
+			status = "disabled";
+		};
+
+		usbh: usb-phy@10002700 {
+			compatible = "brcm,bcm6328-usbh-phy";
+			reg = <0x10002700 0x38>;
+			#phy-cells = <1>;
+
+			clocks = <&periph_clk BCM6328_CLK_USBH>;
+			clock-names = "usbh";
+
+			power-domains = <&periph_pwr BCM6328_POWER_DOMAIN_USBH>;
+
+			resets = <&periph_rst BCM6328_RST_USBH>;
+			reset-names = "usbh";
+
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/brcm/bcm6358-neufbox4-sercomm.dts b/arch/mips/boot/dts/brcm/bcm6358-neufbox4-sercomm.dts
new file mode 100644
index 000000000..c646690ee
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm6358-neufbox4-sercomm.dts
@@ -0,0 +1,48 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "bcm6358.dtsi"
+
+/ {
+	compatible = "sfr,nb4-ser", "brcm,bcm6358";
+	model = "SFR Neufbox 4 (Sercomm)";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x02000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &uart0;
+	};
+};
+
+&leds0 {
+	status = "okay";
+
+	led@0 {
+		reg = <0>;
+		active-low;
+		label = "nb4-ser:white:alarm";
+	};
+	led@2 {
+		reg = <2>;
+		active-low;
+		label = "nb4-ser:white:tv";
+	};
+	led@3 {
+		reg = <3>;
+		active-low;
+		label = "nb4-ser:white:tel";
+	};
+	led@4 {
+		reg = <4>;
+		active-low;
+		label = "nb4-ser:white:adsl";
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/mips/boot/dts/brcm/bcm6358.dtsi b/arch/mips/boot/dts/brcm/bcm6358.dtsi
new file mode 100644
index 000000000..777c4379e
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm6358.dtsi
@@ -0,0 +1,210 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "dt-bindings/clock/bcm6358-clock.h"
+#include "dt-bindings/reset/bcm6358-reset.h"
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "brcm,bcm6358";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mips-hpt-frequency = <150000000>;
+
+		cpu@0 {
+			compatible = "brcm,bmips4350";
+			device_type = "cpu";
+			reg = <0>;
+		};
+
+		cpu@1 {
+			compatible = "brcm,bmips4350";
+			device_type = "cpu";
+			reg = <1>;
+		};
+	};
+
+	clocks {
+		periph_osc: periph-osc {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <50000000>;
+			clock-output-names = "periph";
+		};
+	};
+
+	aliases {
+		pflash = &pflash;
+		serial0 = &uart0;
+		serial1 = &uart1;
+		spi0 = &lsspi;
+	};
+
+	cpu_intc: interrupt-controller {
+		#address-cells = <0>;
+		compatible = "mti,cpu-interrupt-controller";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+
+	ubus {
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		compatible = "simple-bus";
+		ranges;
+
+		periph_clk: clock-controller@fffe0004 {
+			compatible = "brcm,bcm6358-clocks";
+			reg = <0xfffe0004 0x4>;
+			#clock-cells = <1>;
+		};
+
+		pll_cntl: syscon@fffe0008 {
+			compatible = "syscon";
+			reg = <0xfffe0008 0x4>;
+			native-endian;
+
+			reboot {
+				compatible = "syscon-reboot";
+				offset = <0x0>;
+				mask = <0x1>;
+			};
+		};
+
+		periph_intc: interrupt-controller@fffe000c {
+			compatible = "brcm,bcm6345-l1-intc";
+			reg = <0xfffe000c 0x8>,
+			      <0xfffe0038 0x8>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&cpu_intc>;
+			interrupts = <2>, <3>;
+		};
+
+		periph_rst: reset-controller@fffe0034 {
+			compatible = "brcm,bcm6345-reset";
+			reg = <0xfffe0034 0x4>;
+			#reset-cells = <1>;
+		};
+
+		wdt: watchdog@fffe005c {
+			compatible = "brcm,bcm7038-wdt";
+			reg = <0xfffe005c 0xc>;
+
+			clocks = <&periph_osc>;
+			clock-names = "refclk";
+
+			timeout-sec = <30>;
+		};
+
+		leds0: led-controller@fffe00d0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6358-leds";
+			reg = <0xfffe00d0 0x8>;
+
+			status = "disabled";
+		};
+
+		uart0: serial@fffe0100 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0xfffe0100 0x18>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <2>;
+
+			clocks = <&periph_osc>;
+			clock-names = "refclk";
+
+			status = "disabled";
+		};
+
+		uart1: serial@fffe0120 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0xfffe0120 0x18>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <3>;
+
+			clocks = <&periph_osc>;
+			clock-names = "refclk";
+
+			status = "disabled";
+		};
+
+		lsspi: spi@fffe0800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6358-spi";
+			reg = <0xfffe0800 0x70c>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <1>;
+
+			clocks = <&periph_clk BCM6358_CLK_SPI>;
+			clock-names = "spi";
+
+			resets = <&periph_rst BCM6358_RST_SPI>;
+			reset-names = "spi";
+
+			status = "disabled";
+		};
+
+		ehci: usb@fffe1300 {
+			compatible = "brcm,bcm6358-ehci", "generic-ehci";
+			reg = <0xfffe1300 0x100>;
+			big-endian;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <10>;
+
+			phys = <&usbh 0>;
+			phy-names = "usb";
+
+			status = "disabled";
+		};
+
+		ohci: usb@fffe1400 {
+			compatible = "brcm,bcm6358-ohci", "generic-ohci";
+			reg = <0xfffe1400 0x100>;
+			big-endian;
+			no-big-frame-no;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <5>;
+
+			phys = <&usbh 0>;
+			phy-names = "usb";
+
+			status = "disabled";
+		};
+
+		usbh: usb-phy@fffe1500 {
+			compatible = "brcm,bcm6358-usbh-phy";
+			reg = <0xfffe1500 0x38>;
+			#phy-cells = <1>;
+
+			resets = <&periph_rst BCM6358_RST_USBH>;
+			reset-names = "usbh";
+
+			status = "disabled";
+		};
+	};
+
+	pflash: nor@1e000000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "cfi-flash";
+		reg = <0x1e000000 0x2000000>;
+		bank-width = <2>;
+
+		status = "disabled";
+	};
+};
diff --git a/arch/mips/boot/dts/brcm/bcm6362-neufbox6-sercomm.dts b/arch/mips/boot/dts/brcm/bcm6362-neufbox6-sercomm.dts
new file mode 100644
index 000000000..f83d95ca0
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm6362-neufbox6-sercomm.dts
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "bcm6362.dtsi"
+
+/ {
+	compatible = "sfr,nb6-ser", "brcm,bcm6362";
+	model = "SFR NeufBox 6 (Sercomm)";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &uart0;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/mips/boot/dts/brcm/bcm6362.dtsi b/arch/mips/boot/dts/brcm/bcm6362.dtsi
new file mode 100644
index 000000000..d74021925
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm6362.dtsi
@@ -0,0 +1,265 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "dt-bindings/clock/bcm6362-clock.h"
+#include "dt-bindings/reset/bcm6362-reset.h"
+#include "dt-bindings/soc/bcm6362-pm.h"
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "brcm,bcm6362";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mips-hpt-frequency = <200000000>;
+
+		cpu@0 {
+			compatible = "brcm,bmips4350";
+			device_type = "cpu";
+			reg = <0>;
+		};
+
+		cpu@1 {
+			compatible = "brcm,bmips4350";
+			device_type = "cpu";
+			reg = <1>;
+		};
+	};
+
+	clocks {
+		periph_osc: periph-osc {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <50000000>;
+			clock-output-names = "periph";
+		};
+
+		hsspi_osc: hsspi-osc {
+			compatible = "fixed-clock";
+
+			#clock-cells = <0>;
+
+			clock-frequency = <400000000>;
+			clock-output-names = "hsspi_osc";
+		};
+	};
+
+	aliases {
+		nflash = &nflash;
+		serial0 = &uart0;
+		serial1 = &uart1;
+		spi0 = &lsspi;
+		spi1 = &hsspi;
+	};
+
+	cpu_intc: interrupt-controller {
+		#address-cells = <0>;
+		compatible = "mti,cpu-interrupt-controller";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+
+	ubus {
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		compatible = "simple-bus";
+		ranges;
+
+		periph_clk: clock-controller@10000004 {
+			compatible = "brcm,bcm6362-clocks";
+			reg = <0x10000004 0x4>;
+			#clock-cells = <1>;
+		};
+
+		pll_cntl: syscon@10000008 {
+			compatible = "syscon";
+			reg = <0x10000008 0x4>;
+			native-endian;
+
+			reboot {
+				compatible = "syscon-reboot";
+				offset = <0x0>;
+				mask = <0x1>;
+			};
+		};
+
+		periph_rst: reset-controller@10000010 {
+			compatible = "brcm,bcm6345-reset";
+			reg = <0x10000010 0x4>;
+			#reset-cells = <1>;
+		};
+
+		periph_intc: interrupt-controller@10000020 {
+			compatible = "brcm,bcm6345-l1-intc";
+			reg = <0x10000020 0x10>,
+			      <0x10000030 0x10>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&cpu_intc>;
+			interrupts = <2>, <3>;
+		};
+
+		wdt: watchdog@1000005c {
+			compatible = "brcm,bcm7038-wdt";
+			reg = <0x1000005c 0xc>;
+
+			clocks = <&periph_osc>;
+			clock-names = "refclk";
+
+			timeout-sec = <30>;
+		};
+
+		uart0: serial@10000100 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0x10000100 0x18>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <3>;
+
+			clocks = <&periph_osc>;
+			clock-names = "refclk";
+
+			status = "disabled";
+		};
+
+		uart1: serial@10000120 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0x10000120 0x18>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <4>;
+
+			clocks = <&periph_osc>;
+			clock-names = "refclk";
+
+			status = "disabled";
+		};
+
+		nflash: nand@10000200 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,nand-bcm6368",
+				     "brcm,brcmnand-v2.2",
+				     "brcm,brcmnand";
+			reg = <0x10000200 0x180>,
+			      <0x10000600 0x200>,
+			      <0x10000070 0x10>;
+			reg-names = "nand",
+				    "nand-cache",
+				    "nand-int-base";
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <12>;
+
+			clocks = <&periph_clk BCM6362_CLK_NAND>;
+			clock-names = "nand";
+
+			status = "disabled";
+		};
+
+		lsspi: spi@10000800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6358-spi";
+			reg = <0x10000800 0x70c>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <2>;
+
+			clocks = <&periph_clk BCM6362_CLK_SPI>;
+			clock-names = "spi";
+
+			resets = <&periph_rst BCM6362_RST_SPI>;
+			reset-names = "spi";
+
+			status = "disabled";
+		};
+
+		hsspi: spi@10001000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6328-hsspi";
+			reg = <0x10001000 0x600>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <5>;
+
+			clocks = <&periph_clk BCM6362_CLK_HSSPI>,
+				 <&hsspi_osc>;
+			clock-names = "hsspi",
+				      "pll";
+
+			resets = <&periph_rst BCM6362_RST_SPI>;
+			reset-names = "hsspi";
+
+			status = "disabled";
+		};
+
+		periph_pwr: power-controller@10001848 {
+			compatible = "brcm,bcm6362-power-controller";
+			reg = <0x10001848 0x4>;
+			#power-domain-cells = <1>;
+		};
+
+		leds0: led-controller@10001900 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6328-leds";
+			reg = <0x10001900 0x24>;
+
+			status = "disabled";
+		};
+
+		ehci: usb@10002500 {
+			compatible = "brcm,bcm6362-ehci", "generic-ehci";
+			reg = <0x10002500 0x100>;
+			big-endian;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <10>;
+
+			phys = <&usbh 0>;
+			phy-names = "usb";
+
+			status = "disabled";
+		};
+
+		ohci: usb@10002600 {
+			compatible = "brcm,bcm6362-ohci", "generic-ohci";
+			reg = <0x10002600 0x100>;
+			big-endian;
+			no-big-frame-no;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <9>;
+
+			phys = <&usbh 0>;
+			phy-names = "usb";
+
+			status = "disabled";
+		};
+
+		usbh: usb-phy@10002700 {
+			compatible = "brcm,bcm6362-usbh-phy";
+			reg = <0x10002700 0x38>;
+
+			#phy-cells = <1>;
+
+			clocks = <&periph_clk BCM6362_CLK_USBH>;
+			clock-names = "usbh";
+
+			power-domains = <&periph_pwr BCM6362_POWER_DOMAIN_USBH>;
+
+			resets = <&periph_rst BCM6362_RST_USBH>;
+			reset-names = "usbh";
+
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/brcm/bcm6368.dtsi b/arch/mips/boot/dts/brcm/bcm6368.dtsi
new file mode 100644
index 000000000..fc15e2008
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm6368.dtsi
@@ -0,0 +1,247 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "dt-bindings/clock/bcm6368-clock.h"
+#include "dt-bindings/reset/bcm6368-reset.h"
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "brcm,bcm6368";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mips-hpt-frequency = <200000000>;
+
+		cpu@0 {
+			compatible = "brcm,bmips4350";
+			device_type = "cpu";
+			reg = <0>;
+		};
+
+		cpu@1 {
+			compatible = "brcm,bmips4350";
+			device_type = "cpu";
+			reg = <1>;
+		};
+	};
+
+	clocks {
+		periph_osc: periph-osc {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <50000000>;
+			clock-output-names = "periph";
+		};
+	};
+
+	aliases {
+		nflash = &nflash;
+		pflash = &pflash;
+		serial0 = &uart0;
+		serial1 = &uart1;
+		spi0 = &lsspi;
+	};
+
+	cpu_intc: interrupt-controller {
+		#address-cells = <0>;
+		compatible = "mti,cpu-interrupt-controller";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+
+	ubus {
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		compatible = "simple-bus";
+		ranges;
+
+		periph_clk: clock-controller@10000004 {
+			compatible = "brcm,bcm6368-clocks";
+			reg = <0x10000004 0x4>;
+			#clock-cells = <1>;
+		};
+
+		pll_cntl: syscon@100000008 {
+			compatible = "syscon";
+			reg = <0x10000008 0x4>;
+			native-endian;
+
+			reboot {
+				compatible = "syscon-reboot";
+				offset = <0x0>;
+				mask = <0x1>;
+			};
+		};
+
+		periph_rst: reset-controller@10000010 {
+			compatible = "brcm,bcm6345-reset";
+			reg = <0x10000010 0x4>;
+			#reset-cells = <1>;
+		};
+
+		periph_intc: interrupt-controller@10000020 {
+			compatible = "brcm,bcm6345-l1-intc";
+			reg = <0x10000020 0x10>,
+			      <0x10000030 0x10>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&cpu_intc>;
+			interrupts = <2>, <3>;
+		};
+
+		wdt: watchdog@1000005c {
+			compatible = "brcm,bcm7038-wdt";
+			reg = <0x1000005c 0xc>;
+
+			clocks = <&periph_osc>;
+			clock-names = "refclk";
+
+			timeout-sec = <30>;
+		};
+
+		leds0: led-controller@100000d0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6358-leds";
+			reg = <0x100000d0 0x8>;
+
+			status = "disabled";
+		};
+
+		uart0: serial@10000100 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0x10000100 0x18>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <2>;
+
+			clocks = <&periph_osc>;
+			clock-names = "refclk";
+
+			status = "disabled";
+		};
+
+		uart1: serial@10000120 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0x10000120 0x18>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <3>;
+
+			clocks = <&periph_osc>;
+			clock-names = "refclk";
+
+			status = "disabled";
+		};
+
+		nflash: nand@10000200 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,nand-bcm6368",
+				     "brcm,brcmnand-v2.1",
+				     "brcm,brcmnand";
+			reg = <0x10000200 0x180>,
+			      <0x10000600 0x200>,
+			      <0x10000070 0x10>;
+			reg-names = "nand",
+				    "nand-cache",
+				    "nand-int-base";
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <10>;
+
+			clocks = <&periph_clk BCM6368_CLK_NAND>;
+			clock-names = "nand";
+
+			status = "disabled";
+		};
+
+		lsspi: spi@10000800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6358-spi";
+			reg = <0x10000800 0x70c>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <1>;
+
+			clocks = <&periph_clk BCM6368_CLK_SPI>;
+			clock-names = "spi";
+
+			resets = <&periph_rst BCM6368_RST_SPI>;
+			reset-names = "spi";
+
+			status = "disabled";
+		};
+
+		ehci: usb@10001500 {
+			compatible = "brcm,bcm6368-ehci", "generic-ehci";
+			reg = <0x10001500 0x100>;
+			big-endian;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <7>;
+
+			phys = <&usbh 0>;
+			phy-names = "usb";
+
+			status = "disabled";
+		};
+
+		ohci: usb@10001600 {
+			compatible = "brcm,bcm6368-ohci", "generic-ohci";
+			reg = <0x10001600 0x100>;
+			big-endian;
+			no-big-frame-no;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <5>;
+
+			phys = <&usbh 0>;
+			phy-names = "usb";
+
+			status = "disabled";
+		};
+
+		usbh: usb-phy@10001700 {
+			compatible = "brcm,bcm6368-usbh-phy";
+			reg = <0x10001700 0x38>;
+			#phy-cells = <1>;
+
+			clocks = <&periph_clk BCM6368_CLK_USBH>;
+			clock-names = "usbh";
+
+			resets = <&periph_rst BCM6368_RST_USBH>;
+			reset-names = "usbh";
+
+			status = "disabled";
+		};
+
+		random: rng@10004180 {
+			compatible = "brcm,bcm6368-rng";
+			reg = <0x10004180 0x14>;
+
+			clocks = <&periph_clk BCM6368_CLK_IPSEC>;
+			clock-names = "ipsec";
+
+			resets = <&periph_rst BCM6368_RST_IPSEC>;
+			reset-names = "ipsec";
+		};
+	};
+
+	pflash: nor@18000000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "cfi-flash";
+		reg = <0x18000000 0x2000000>;
+		bank-width = <2>;
+
+		status = "disabled";
+	};
+};
diff --git a/arch/mips/boot/dts/brcm/bcm7125.dtsi b/arch/mips/boot/dts/brcm/bcm7125.dtsi
new file mode 100644
index 000000000..5bf77b6fc
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm7125.dtsi
@@ -0,0 +1,281 @@
+// SPDX-License-Identifier: GPL-2.0
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "brcm,bcm7125";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mips-hpt-frequency = <202500000>;
+
+		cpu@0 {
+			compatible = "brcm,bmips4380";
+			device_type = "cpu";
+			reg = <0>;
+		};
+
+		cpu@1 {
+			compatible = "brcm,bmips4380";
+			device_type = "cpu";
+			reg = <1>;
+		};
+	};
+
+	aliases {
+		uart0 = &uart0;
+	};
+
+	cpu_intc: interrupt-controller {
+		#address-cells = <0>;
+		compatible = "mti,cpu-interrupt-controller";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+
+	clocks {
+		uart_clk: uart_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <81000000>;
+		};
+
+		upg_clk: upg_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <27000000>;
+		};
+	};
+
+	rdb {
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		compatible = "simple-bus";
+		ranges = <0 0x10000000 0x01000000>;
+
+		periph_intc: interrupt-controller@441400 {
+			compatible = "brcm,bcm7038-l1-intc";
+			reg = <0x441400 0x30>, <0x441600 0x30>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&cpu_intc>;
+			interrupts = <2>, <3>;
+		};
+
+		sun_l2_intc: interrupt-controller@401800 {
+			compatible = "brcm,l2-intc";
+			reg = <0x401800 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <23>;
+		};
+
+		gisb-arb@400000 {
+			compatible = "brcm,bcm7400-gisb-arb";
+			reg = <0x400000 0xdc>;
+			native-endian;
+			interrupt-parent = <&sun_l2_intc>;
+			interrupts = <0>, <2>;
+			brcm,gisb-arb-master-mask = <0x2f7>;
+			brcm,gisb-arb-master-names = "ssp_0", "cpu_0", "pci_0",
+						     "bsp_0", "rdc_0", "rptd_0",
+						     "avd_0", "jtag_0";
+		};
+
+		upg_irq0_intc: interrupt-controller@406780 {
+			compatible = "brcm,bcm7120-l2-intc";
+			reg = <0x406780 0x8>;
+
+			brcm,int-map-mask = <0x44>, <0xf000000>, <0x100000>;
+			brcm,int-fwd-mask = <0x70000>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <18>, <19>, <20>;
+			interrupt-names = "upg_main", "upg_bsc", "upg_spi";
+		};
+
+		sun_top_ctrl: syscon@404000 {
+			compatible = "brcm,bcm7125-sun-top-ctrl", "syscon";
+			reg = <0x404000 0x60c>;
+			native-endian;
+		};
+
+		reboot {
+			compatible = "brcm,bcm7038-reboot";
+			syscon = <&sun_top_ctrl 0x8 0x14>;
+		};
+
+		uart0: serial@406b00 {
+			compatible = "ns16550a";
+			reg = <0x406b00 0x20>;
+			reg-io-width = <0x4>;
+			reg-shift = <0x2>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <21>;
+			clocks = <&uart_clk>;
+			status = "disabled";
+		};
+
+		uart1: serial@406b40 {
+			compatible = "ns16550a";
+			reg = <0x406b40 0x20>;
+			reg-io-width = <0x4>;
+			reg-shift = <0x2>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <64>;
+			clocks = <&uart_clk>;
+			status = "disabled";
+		};
+
+		uart2: serial@406b80 {
+			compatible = "ns16550a";
+			reg = <0x406b80 0x20>;
+			reg-io-width = <0x4>;
+			reg-shift = <0x2>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <65>;
+			clocks = <&uart_clk>;
+			status = "disabled";
+		};
+
+		bsca: i2c@406200 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_irq0_intc>;
+		      reg = <0x406200 0x58>;
+		      interrupts = <24>;
+		      interrupt-names = "upg_bsca";
+		      status = "disabled";
+		};
+
+		bscb: i2c@406280 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_irq0_intc>;
+		      reg = <0x406280 0x58>;
+		      interrupts = <25>;
+		      interrupt-names = "upg_bscb";
+		      status = "disabled";
+		};
+
+		bscc: i2c@406300 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_irq0_intc>;
+		      reg = <0x406300 0x58>;
+		      interrupts = <26>;
+		      interrupt-names = "upg_bscc";
+		      status = "disabled";
+		};
+
+		bscd: i2c@406380 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_irq0_intc>;
+		      reg = <0x406380 0x58>;
+		      interrupts = <27>;
+		      interrupt-names = "upg_bscd";
+		      status = "disabled";
+		};
+
+		pwma: pwm@406580 {
+			compatible = "brcm,bcm7038-pwm";
+			reg = <0x406580 0x28>;
+			#pwm-cells = <2>;
+			clocks = <&upg_clk>;
+			status = "disabled";
+		};
+
+		watchdog: watchdog@4067e8 {
+			clocks = <&upg_clk>;
+			compatible = "brcm,bcm7038-wdt";
+			reg = <0x4067e8 0x14>;
+			status = "disabled";
+		};
+
+		upg_gio: gpio@406700 {
+			compatible = "brcm,brcmstb-gpio";
+			reg = <0x406700 0x80>;
+			#gpio-cells = <2>;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			interrupt-controller;
+			interrupt-parent = <&upg_irq0_intc>;
+			interrupts = <6>;
+			brcm,gpio-bank-widths = <32 32 32 18>;
+		};
+
+		ehci0: usb@488300 {
+			compatible = "brcm,bcm7125-ehci", "generic-ehci";
+			reg = <0x488300 0x100>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <60>;
+			status = "disabled";
+		};
+
+		ohci0: usb@488400 {
+			compatible = "brcm,bcm7125-ohci", "generic-ohci";
+			reg = <0x488400 0x100>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <61>;
+			status = "disabled";
+		};
+
+		spi_l2_intc: interrupt-controller@411d00 {
+			compatible = "brcm,l2-intc";
+			reg = <0x411d00 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <79>;
+		};
+
+		qspi: spi@443000 {
+			#address-cells = <0x1>;
+			#size-cells = <0x0>;
+			compatible = "brcm,spi-bcm-qspi",
+				     "brcm,spi-brcmstb-qspi";
+			clocks = <&upg_clk>;
+			reg = <0x440920 0x4 0x443200 0x188 0x443000 0x50>;
+			reg-names = "cs_reg", "hif_mspi", "bspi";
+			interrupts = <0x0 0x1 0x2 0x3 0x4 0x5 0x6>;
+			interrupt-parent = <&spi_l2_intc>;
+			interrupt-names = "spi_lr_fullness_reached",
+					  "spi_lr_session_aborted",
+					  "spi_lr_impatient",
+					  "spi_lr_session_done",
+					  "spi_lr_overread",
+					  "mspi_done",
+					  "mspi_halted";
+			status = "disabled";
+		};
+
+		mspi: spi@406400 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,spi-bcm-qspi",
+				     "brcm,spi-brcmstb-mspi";
+			clocks = <&upg_clk>;
+			reg = <0x406400 0x180>;
+			reg-names = "mspi";
+			interrupts = <0x14>;
+			interrupt-parent = <&upg_irq0_intc>;
+			interrupt-names = "mspi_done";
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/brcm/bcm7346.dtsi b/arch/mips/boot/dts/brcm/bcm7346.dtsi
new file mode 100644
index 000000000..2afa0dada
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm7346.dtsi
@@ -0,0 +1,549 @@
+// SPDX-License-Identifier: GPL-2.0
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "brcm,bcm7346";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mips-hpt-frequency = <163125000>;
+
+		cpu@0 {
+			compatible = "brcm,bmips5000";
+			device_type = "cpu";
+			reg = <0>;
+		};
+
+		cpu@1 {
+			compatible = "brcm,bmips5000";
+			device_type = "cpu";
+			reg = <1>;
+		};
+	};
+
+	aliases {
+		uart0 = &uart0;
+	};
+
+	cpu_intc: interrupt-controller {
+		#address-cells = <0>;
+		compatible = "mti,cpu-interrupt-controller";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+
+	clocks {
+		uart_clk: uart_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <81000000>;
+		};
+
+		upg_clk: upg_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <27000000>;
+		};
+	};
+
+	rdb {
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		compatible = "simple-bus";
+		ranges = <0 0x10000000 0x01000000>;
+
+		periph_intc: interrupt-controller@411400 {
+			compatible = "brcm,bcm7038-l1-intc";
+			reg = <0x411400 0x30>, <0x411600 0x30>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&cpu_intc>;
+			interrupts = <2>, <3>;
+		};
+
+		sun_l2_intc: interrupt-controller@403000 {
+			compatible = "brcm,l2-intc";
+			reg = <0x403000 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <51>;
+		};
+
+		gisb-arb@400000 {
+			compatible = "brcm,bcm7400-gisb-arb";
+			reg = <0x400000 0xdc>;
+			native-endian;
+			interrupt-parent = <&sun_l2_intc>;
+			interrupts = <0>, <2>;
+			brcm,gisb-arb-master-mask = <0x673>;
+			brcm,gisb-arb-master-names = "ssp_0", "cpu_0", "bsp_0",
+						     "rdc_0", "raaga_0",
+						     "jtag_0", "svd_0";
+		};
+
+		upg_irq0_intc: interrupt-controller@406780 {
+			compatible = "brcm,bcm7120-l2-intc";
+			reg = <0x406780 0x8>;
+
+			brcm,int-map-mask = <0x44>, <0xf000000>;
+			brcm,int-fwd-mask = <0x70000>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <59>, <57>;
+			interrupt-names = "upg_main", "upg_bsc";
+		};
+
+		upg_aon_irq0_intc: interrupt-controller@408b80 {
+			compatible = "brcm,bcm7120-l2-intc";
+			reg = <0x408b80 0x8>;
+
+			brcm,int-map-mask = <0x40>, <0x8000000>, <0x100000>;
+			brcm,int-fwd-mask = <0>;
+			brcm,irq-can-wake;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <60>, <58>, <62>;
+			interrupt-names = "upg_main_aon", "upg_bsc_aon",
+					  "upg_spi";
+		};
+
+		sun_top_ctrl: syscon@404000 {
+			compatible = "brcm,bcm7346-sun-top-ctrl", "syscon";
+			reg = <0x404000 0x51c>;
+			native-endian;
+		};
+
+		reboot {
+			compatible = "brcm,brcmstb-reboot";
+			syscon = <&sun_top_ctrl 0x304 0x308>;
+		};
+
+		uart0: serial@406900 {
+			compatible = "ns16550a";
+			reg = <0x406900 0x20>;
+			reg-io-width = <0x4>;
+			reg-shift = <0x2>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <64>;
+			clocks = <&uart_clk>;
+			status = "disabled";
+		};
+
+		uart1: serial@406940 {
+			compatible = "ns16550a";
+			reg = <0x406940 0x20>;
+			reg-io-width = <0x4>;
+			reg-shift = <0x2>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <65>;
+			clocks = <&uart_clk>;
+			status = "disabled";
+		};
+
+		uart2: serial@406980 {
+			compatible = "ns16550a";
+			reg = <0x406980 0x20>;
+			reg-io-width = <0x4>;
+			reg-shift = <0x2>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <66>;
+			clocks = <&uart_clk>;
+			status = "disabled";
+		};
+
+		bsca: i2c@406200 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_irq0_intc>;
+		      reg = <0x406200 0x58>;
+		      interrupts = <24>;
+		      interrupt-names = "upg_bsca";
+		      status = "disabled";
+		};
+
+		bscb: i2c@406280 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_irq0_intc>;
+		      reg = <0x406280 0x58>;
+		      interrupts = <25>;
+		      interrupt-names = "upg_bscb";
+		      status = "disabled";
+		};
+
+		bscc: i2c@406300 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_irq0_intc>;
+		      reg = <0x406300 0x58>;
+		      interrupts = <26>;
+		      interrupt-names = "upg_bscc";
+		      status = "disabled";
+		};
+
+		bscd: i2c@406380 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_irq0_intc>;
+		      reg = <0x406380 0x58>;
+		      interrupts = <27>;
+		      interrupt-names = "upg_bscd";
+		      status = "disabled";
+		};
+
+		bsce: i2c@408980 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_aon_irq0_intc>;
+		      reg = <0x408980 0x58>;
+		      interrupts = <27>;
+		      interrupt-names = "upg_bsce";
+		      status = "disabled";
+		};
+
+		pwma: pwm@406580 {
+			compatible = "brcm,bcm7038-pwm";
+			reg = <0x406580 0x28>;
+			#pwm-cells = <2>;
+			clocks = <&upg_clk>;
+			status = "disabled";
+		};
+
+		pwmb: pwm@406800 {
+			compatible = "brcm,bcm7038-pwm";
+			reg = <0x406800 0x28>;
+			#pwm-cells = <2>;
+			clocks = <&upg_clk>;
+			status = "disabled";
+		};
+
+		watchdog: watchdog@4067e8 {
+			clocks = <&upg_clk>;
+			compatible = "brcm,bcm7038-wdt";
+			reg = <0x4067e8 0x14>;
+			status = "disabled";
+		};
+
+		aon_pm_l2_intc: interrupt-controller@408440 {
+			compatible = "brcm,l2-intc";
+			reg = <0x408440 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <53>;
+			brcm,irq-can-wake;
+		};
+
+		aon_ctrl: syscon@408000 {
+			compatible = "brcm,brcmstb-aon-ctrl";
+			reg = <0x408000 0x100>, <0x408200 0x200>;
+			reg-names = "aon-ctrl", "aon-sram";
+		};
+
+		timers: timer@4067c0 {
+			compatible = "brcm,brcmstb-timers";
+			reg = <0x4067c0 0x40>;
+		};
+
+		upg_gio: gpio@406700 {
+			compatible = "brcm,brcmstb-gpio";
+			reg = <0x406700 0x60>;
+			#gpio-cells = <2>;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			interrupt-controller;
+			interrupt-parent = <&upg_irq0_intc>;
+			interrupts = <6>;
+			brcm,gpio-bank-widths = <32 32 16>;
+		};
+
+		upg_gio_aon: gpio@408c00 {
+			compatible = "brcm,brcmstb-gpio";
+			reg = <0x408c00 0x60>;
+			#gpio-cells = <2>;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			interrupt-controller;
+			interrupt-parent = <&upg_aon_irq0_intc>;
+			interrupts = <6>;
+			interrupts-extended = <&upg_aon_irq0_intc 6>,
+					      <&aon_pm_l2_intc 5>;
+			wakeup-source;
+			brcm,gpio-bank-widths = <27 32 2>;
+		};
+
+		enet0: ethernet@430000 {
+			phy-mode = "internal";
+			phy-handle = <&phy1>;
+			mac-address = [ 00 10 18 36 23 1a ];
+			compatible = "brcm,genet-v2";
+			#address-cells = <0x1>;
+			#size-cells = <0x1>;
+			reg = <0x430000 0x4c8c>;
+			interrupts = <24>, <25>;
+			interrupt-parent = <&periph_intc>;
+			status = "disabled";
+
+			mdio@e14 {
+				compatible = "brcm,genet-mdio-v2";
+				#address-cells = <0x1>;
+				#size-cells = <0x0>;
+				reg = <0xe14 0x8>;
+
+				phy1: ethernet-phy@1 {
+					max-speed = <100>;
+					reg = <0x1>;
+					compatible = "brcm,40nm-ephy",
+						"ethernet-phy-ieee802.3-c22";
+				};
+			};
+		};
+
+		ehci0: usb@480300 {
+			compatible = "brcm,bcm7346-ehci", "generic-ehci";
+			reg = <0x480300 0x100>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <68>;
+			status = "disabled";
+		};
+
+		ohci0: usb@480400 {
+			compatible = "brcm,bcm7346-ohci", "generic-ohci";
+			reg = <0x480400 0x100>;
+			native-endian;
+			no-big-frame-no;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <70>;
+			status = "disabled";
+		};
+
+		ehci1: usb@480500 {
+			compatible = "brcm,bcm7346-ehci", "generic-ehci";
+			reg = <0x480500 0x100>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <69>;
+			status = "disabled";
+		};
+
+		ohci1: usb@480600 {
+			compatible = "brcm,bcm7346-ohci", "generic-ohci";
+			reg = <0x480600 0x100>;
+			native-endian;
+			no-big-frame-no;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <71>;
+			status = "disabled";
+		};
+
+		ehci2: usb@490300 {
+			compatible = "brcm,bcm7346-ehci", "generic-ehci";
+			reg = <0x490300 0x100>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <73>;
+			status = "disabled";
+		};
+
+		ohci2: usb@490400 {
+			compatible = "brcm,bcm7346-ohci", "generic-ohci";
+			reg = <0x490400 0x100>;
+			native-endian;
+			no-big-frame-no;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <75>;
+			status = "disabled";
+		};
+
+		ehci3: usb@490500 {
+			compatible = "brcm,bcm7346-ehci", "generic-ehci";
+			reg = <0x490500 0x100>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <74>;
+			status = "disabled";
+		};
+
+		ohci3: usb@490600 {
+			compatible = "brcm,bcm7346-ohci", "generic-ohci";
+			reg = <0x490600 0x100>;
+			native-endian;
+			no-big-frame-no;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <76>;
+			status = "disabled";
+		};
+
+		hif_l2_intc: interrupt-controller@411000 {
+			compatible = "brcm,l2-intc";
+			reg = <0x411000 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <30>;
+		};
+
+		nand: nand@412800 {
+			compatible = "brcm,brcmnand-v5.0", "brcm,brcmnand";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg-names = "nand";
+			reg = <0x412800 0x400>;
+			interrupt-parent = <&hif_l2_intc>;
+			interrupts = <24>;
+			status = "disabled";
+		};
+
+		sata: sata@181000 {
+			compatible = "brcm,bcm7425-ahci", "brcm,sata3-ahci";
+			reg-names = "ahci", "top-ctrl";
+			reg = <0x181000 0xa9c>, <0x180020 0x1c>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <40>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sata0: sata-port@0 {
+				reg = <0>;
+				phys = <&sata_phy0>;
+			};
+
+			sata1: sata-port@1 {
+				reg = <1>;
+				phys = <&sata_phy1>;
+			};
+		};
+
+		sata_phy: sata-phy@180100 {
+			compatible = "brcm,bcm7425-sata-phy", "brcm,phy-sata3";
+			reg = <0x180100 0x0eff>;
+			reg-names = "phy";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sata_phy0: sata-phy@0 {
+				reg = <0>;
+				#phy-cells = <0>;
+			};
+
+			sata_phy1: sata-phy@1 {
+				reg = <1>;
+				#phy-cells = <0>;
+			};
+		};
+
+		sdhci0: sdhci@413500 {
+			compatible = "brcm,bcm7425-sdhci";
+			reg = <0x413500 0x100>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <85>;
+			status = "disabled";
+		};
+
+		spi_l2_intc: interrupt-controller@411d00 {
+			compatible = "brcm,l2-intc";
+			reg = <0x411d00 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <31>;
+		};
+
+		qspi: spi@413000 {
+			#address-cells = <0x1>;
+			#size-cells = <0x0>;
+			compatible = "brcm,spi-bcm-qspi",
+				     "brcm,spi-brcmstb-qspi";
+			clocks = <&upg_clk>;
+			reg = <0x410920 0x4 0x413200 0x188 0x413000 0x50>;
+			reg-names = "cs_reg", "hif_mspi", "bspi";
+			interrupts = <0x0 0x1 0x2 0x3 0x4 0x5 0x6>;
+			interrupt-parent = <&spi_l2_intc>;
+			interrupt-names = "spi_lr_fullness_reached",
+					  "spi_lr_session_aborted",
+					  "spi_lr_impatient",
+					  "spi_lr_session_done",
+					  "spi_lr_overread",
+					  "mspi_done",
+					  "mspi_halted";
+			status = "disabled";
+		};
+
+		mspi: spi@408a00 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,spi-bcm-qspi",
+				     "brcm,spi-brcmstb-mspi";
+			clocks = <&upg_clk>;
+			reg = <0x408a00 0x180>;
+			reg-names = "mspi";
+			interrupts = <0x14>;
+			interrupt-parent = <&upg_aon_irq0_intc>;
+			interrupt-names = "mspi_done";
+			status = "disabled";
+		};
+
+		waketimer: waketimer@408e80 {
+			compatible = "brcm,brcmstb-waketimer";
+			reg = <0x408e80 0x14>;
+			interrupts = <0x3>;
+			interrupt-parent = <&aon_pm_l2_intc>;
+			interrupt-names = "timer";
+			clocks = <&upg_clk>;
+			status = "disabled";
+		};
+	};
+
+	memory_controllers {
+		compatible = "simple-bus";
+		ranges = <0x0 0x103b0000 0xa000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		memory-controller@0 {
+			compatible = "brcm,brcmstb-memc", "simple-bus";
+			ranges = <0x0 0x0 0xa000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			memc-arb@1000 {
+				compatible = "brcm,brcmstb-memc-arb";
+				reg = <0x1000 0x248>;
+			};
+
+			memc-ddr@2000 {
+				compatible = "brcm,brcmstb-memc-ddr";
+				reg = <0x2000 0x300>;
+			};
+
+			ddr-phy@6000 {
+				compatible = "brcm,brcmstb-ddr-phy";
+				reg = <0x6000 0xc8>;
+			};
+
+			shimphy@8000 {
+				compatible = "brcm,brcmstb-ddr-shimphy";
+				reg = <0x8000 0x13c>;
+			};
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/brcm/bcm7358.dtsi b/arch/mips/boot/dts/brcm/bcm7358.dtsi
new file mode 100644
index 000000000..6375fc77f
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm7358.dtsi
@@ -0,0 +1,383 @@
+// SPDX-License-Identifier: GPL-2.0
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "brcm,bcm7358";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mips-hpt-frequency = <375000000>;
+
+		cpu@0 {
+			compatible = "brcm,bmips3300";
+			device_type = "cpu";
+			reg = <0>;
+		};
+	};
+
+	aliases {
+		uart0 = &uart0;
+	};
+
+	cpu_intc: interrupt-controller {
+		#address-cells = <0>;
+		compatible = "mti,cpu-interrupt-controller";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+
+	clocks {
+		uart_clk: uart_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <81000000>;
+		};
+
+		upg_clk: upg_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <27000000>;
+		};
+	};
+
+	rdb {
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		compatible = "simple-bus";
+		ranges = <0 0x10000000 0x01000000>;
+
+		periph_intc: interrupt-controller@411400 {
+			compatible = "brcm,bcm7038-l1-intc";
+			reg = <0x411400 0x30>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&cpu_intc>;
+			interrupts = <2>;
+		};
+
+		sun_l2_intc: interrupt-controller@403000 {
+			compatible = "brcm,l2-intc";
+			reg = <0x403000 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <48>;
+		};
+
+		gisb-arb@400000 {
+			compatible = "brcm,bcm7400-gisb-arb";
+			reg = <0x400000 0xdc>;
+			native-endian;
+			interrupt-parent = <&sun_l2_intc>;
+			interrupts = <0>, <2>;
+			brcm,gisb-arb-master-mask = <0x2f3>;
+			brcm,gisb-arb-master-names = "ssp_0", "cpu_0", "bsp_0",
+						     "rdc_0", "raaga_0",
+						     "avd_0", "jtag_0";
+		};
+
+		upg_irq0_intc: interrupt-controller@406600 {
+			compatible = "brcm,bcm7120-l2-intc";
+			reg = <0x406600 0x8>;
+
+			brcm,int-map-mask = <0x44>, <0x7000000>;
+			brcm,int-fwd-mask = <0x70000>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <56>, <54>;
+			interrupt-names = "upg_main", "upg_bsc";
+		};
+
+		upg_aon_irq0_intc: interrupt-controller@408b80 {
+			compatible = "brcm,bcm7120-l2-intc";
+			reg = <0x408b80 0x8>;
+
+			brcm,int-map-mask = <0x40>, <0x8000000>, <0x100000>;
+			brcm,int-fwd-mask = <0>;
+			brcm,irq-can-wake;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <57>, <55>, <59>;
+			interrupt-names = "upg_main_aon", "upg_bsc_aon",
+					  "upg_spi";
+		};
+
+		sun_top_ctrl: syscon@404000 {
+			compatible = "brcm,bcm7358-sun-top-ctrl", "syscon";
+			reg = <0x404000 0x51c>;
+			native-endian;
+		};
+
+		reboot {
+			compatible = "brcm,brcmstb-reboot";
+			syscon = <&sun_top_ctrl 0x304 0x308>;
+		};
+
+		uart0: serial@406800 {
+			compatible = "ns16550a";
+			reg = <0x406800 0x20>;
+			reg-io-width = <0x4>;
+			reg-shift = <0x2>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <61>;
+			clocks = <&uart_clk>;
+			status = "disabled";
+		};
+
+		uart1: serial@406840 {
+			compatible = "ns16550a";
+			reg = <0x406840 0x20>;
+			reg-io-width = <0x4>;
+			reg-shift = <0x2>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <62>;
+			clocks = <&uart_clk>;
+			status = "disabled";
+		};
+
+		uart2: serial@406880 {
+			compatible = "ns16550a";
+			reg = <0x406880 0x20>;
+			reg-io-width = <0x4>;
+			reg-shift = <0x2>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <63>;
+			clocks = <&uart_clk>;
+			status = "disabled";
+		};
+
+		bsca: i2c@406200 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_irq0_intc>;
+		      reg = <0x406200 0x58>;
+		      interrupts = <24>;
+		      interrupt-names = "upg_bsca";
+		      status = "disabled";
+		};
+
+		bscb: i2c@406280 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_irq0_intc>;
+		      reg = <0x406280 0x58>;
+		      interrupts = <25>;
+		      interrupt-names = "upg_bscb";
+		      status = "disabled";
+		};
+
+		bscc: i2c@406300 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_irq0_intc>;
+		      reg = <0x406300 0x58>;
+		      interrupts = <26>;
+		      interrupt-names = "upg_bscc";
+		      status = "disabled";
+		};
+
+		bscd: i2c@408980 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_aon_irq0_intc>;
+		      reg = <0x408980 0x58>;
+		      interrupts = <27>;
+		      interrupt-names = "upg_bscd";
+		      status = "disabled";
+		};
+
+		pwma: pwm@406400 {
+			compatible = "brcm,bcm7038-pwm";
+			reg = <0x406400 0x28>;
+			#pwm-cells = <2>;
+			clocks = <&upg_clk>;
+			status = "disabled";
+		};
+
+		pwmb: pwm@406700 {
+			compatible = "brcm,bcm7038-pwm";
+			reg = <0x406700 0x28>;
+			#pwm-cells = <2>;
+			clocks = <&upg_clk>;
+			status = "disabled";
+		};
+
+		watchdog: watchdog@4066a8 {
+			clocks = <&upg_clk>;
+			compatible = "brcm,bcm7038-wdt";
+			reg = <0x4066a8 0x14>;
+			status = "disabled";
+		};
+
+		aon_pm_l2_intc: interrupt-controller@408240 {
+			compatible = "brcm,l2-intc";
+			reg = <0x408240 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <50>;
+			brcm,irq-can-wake;
+		};
+
+		upg_gio: gpio@406500 {
+			compatible = "brcm,brcmstb-gpio";
+			reg = <0x406500 0xa0>;
+			#gpio-cells = <2>;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			interrupt-controller;
+			interrupt-parent = <&upg_irq0_intc>;
+			interrupts = <6>;
+			brcm,gpio-bank-widths = <32 32 32 29 4>;
+		};
+
+		upg_gio_aon: gpio@408c00 {
+			compatible = "brcm,brcmstb-gpio";
+			reg = <0x408c00 0x60>;
+			#gpio-cells = <2>;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			interrupt-controller;
+			interrupt-parent = <&upg_aon_irq0_intc>;
+			interrupts = <6>;
+			interrupts-extended = <&upg_aon_irq0_intc 6>,
+					      <&aon_pm_l2_intc 5>;
+			wakeup-source;
+			brcm,gpio-bank-widths = <21 32 2>;
+		};
+
+		enet0: ethernet@430000 {
+			phy-mode = "internal";
+			phy-handle = <&phy1>;
+			mac-address = [ 00 10 18 36 23 1a ];
+			compatible = "brcm,genet-v2";
+			#address-cells = <0x1>;
+			#size-cells = <0x1>;
+			reg = <0x430000 0x4c8c>;
+			interrupts = <24>, <25>;
+			interrupt-parent = <&periph_intc>;
+			status = "disabled";
+
+			mdio@e14 {
+				compatible = "brcm,genet-mdio-v2";
+				#address-cells = <0x1>;
+				#size-cells = <0x0>;
+				reg = <0xe14 0x8>;
+
+				phy1: ethernet-phy@1 {
+					max-speed = <100>;
+					reg = <0x1>;
+					compatible = "brcm,40nm-ephy",
+						"ethernet-phy-ieee802.3-c22";
+				};
+			};
+		};
+
+		ehci0: usb@480300 {
+			compatible = "brcm,bcm7358-ehci", "generic-ehci";
+			reg = <0x480300 0x100>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <65>;
+			status = "disabled";
+		};
+
+		ohci0: usb@480400 {
+			compatible = "brcm,bcm7358-ohci", "generic-ohci";
+			reg = <0x480400 0x100>;
+			native-endian;
+			no-big-frame-no;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <66>;
+			status = "disabled";
+		};
+
+		hif_l2_intc: interrupt-controller@411000 {
+			compatible = "brcm,l2-intc";
+			reg = <0x411000 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <30>;
+		};
+
+		nand: nand@412800 {
+			compatible = "brcm,brcmnand-v5.0", "brcm,brcmnand";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg-names = "nand";
+			reg = <0x412800 0x400>;
+			interrupt-parent = <&hif_l2_intc>;
+			interrupts = <24>;
+			status = "disabled";
+		};
+
+		spi_l2_intc: interrupt-controller@411d00 {
+			compatible = "brcm,l2-intc";
+			reg = <0x411d00 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <31>;
+		};
+
+		qspi: spi@413000 {
+			#address-cells = <0x1>;
+			#size-cells = <0x0>;
+			compatible = "brcm,spi-bcm-qspi",
+				     "brcm,spi-brcmstb-qspi";
+			clocks = <&upg_clk>;
+			reg = <0x410920 0x4 0x413200 0x188 0x413000 0x50>;
+			reg-names = "cs_reg", "hif_mspi", "bspi";
+			interrupts = <0x0 0x1 0x2 0x3 0x4 0x5 0x6>;
+			interrupt-parent = <&spi_l2_intc>;
+			interrupt-names = "spi_lr_fullness_reached",
+					  "spi_lr_session_aborted",
+					  "spi_lr_impatient",
+					  "spi_lr_session_done",
+					  "spi_lr_overread",
+					  "mspi_done",
+					  "mspi_halted";
+			status = "disabled";
+		};
+
+		mspi: spi@408a00 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,spi-bcm-qspi",
+				     "brcm,spi-brcmstb-mspi";
+			clocks = <&upg_clk>;
+			reg = <0x408a00 0x180>;
+			reg-names = "mspi";
+			interrupts = <0x14>;
+			interrupt-parent = <&upg_aon_irq0_intc>;
+			interrupt-names = "mspi_done";
+			status = "disabled";
+		};
+
+		waketimer: waketimer@408e80 {
+			compatible = "brcm,brcmstb-waketimer";
+			reg = <0x408e80 0x14>;
+			interrupts = <0x3>;
+			interrupt-parent = <&aon_pm_l2_intc>;
+			interrupt-names = "timer";
+			clocks = <&upg_clk>;
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/brcm/bcm7360.dtsi b/arch/mips/boot/dts/brcm/bcm7360.dtsi
new file mode 100644
index 000000000..a57cacea9
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm7360.dtsi
@@ -0,0 +1,468 @@
+// SPDX-License-Identifier: GPL-2.0
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "brcm,bcm7360";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mips-hpt-frequency = <375000000>;
+
+		cpu@0 {
+			compatible = "brcm,bmips3300";
+			device_type = "cpu";
+			reg = <0>;
+		};
+	};
+
+	aliases {
+		uart0 = &uart0;
+	};
+
+	cpu_intc: interrupt-controller {
+		#address-cells = <0>;
+		compatible = "mti,cpu-interrupt-controller";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+
+	clocks {
+		uart_clk: uart_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <81000000>;
+		};
+
+		upg_clk: upg_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <27000000>;
+		};
+	};
+
+	rdb {
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		compatible = "simple-bus";
+		ranges = <0 0x10000000 0x01000000>;
+
+		periph_intc: interrupt-controller@411400 {
+			compatible = "brcm,bcm7038-l1-intc";
+			reg = <0x411400 0x30>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&cpu_intc>;
+			interrupts = <2>;
+		};
+
+		sun_l2_intc: interrupt-controller@403000 {
+			compatible = "brcm,l2-intc";
+			reg = <0x403000 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <48>;
+		};
+
+		gisb-arb@400000 {
+			compatible = "brcm,bcm7400-gisb-arb";
+			reg = <0x400000 0xdc>;
+			native-endian;
+			interrupt-parent = <&sun_l2_intc>;
+			interrupts = <0>, <2>;
+			brcm,gisb-arb-master-mask = <0x2f3>;
+			brcm,gisb-arb-master-names = "ssp_0", "cpu_0", "bsp_0",
+						     "rdc_0", "raaga_0",
+						     "avd_0", "jtag_0";
+		};
+
+		upg_irq0_intc: interrupt-controller@406600 {
+			compatible = "brcm,bcm7120-l2-intc";
+			reg = <0x406600 0x8>;
+
+			brcm,int-map-mask = <0x44>, <0x7000000>;
+			brcm,int-fwd-mask = <0x70000>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <56>, <54>;
+			interrupt-names = "upg_main", "upg_bsc";
+		};
+
+		upg_aon_irq0_intc: interrupt-controller@408b80 {
+			compatible = "brcm,bcm7120-l2-intc";
+			reg = <0x408b80 0x8>;
+
+			brcm,int-map-mask = <0x40>, <0x8000000>, <0x100000>;
+			brcm,int-fwd-mask = <0>;
+			brcm,irq-can-wake;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <57>, <55>, <59>;
+			interrupt-names = "upg_main_aon", "upg_bsc_aon",
+					  "upg_spi";
+		};
+
+		sun_top_ctrl: syscon@404000 {
+			compatible = "brcm,bcm7360-sun-top-ctrl", "syscon";
+			reg = <0x404000 0x51c>;
+			native-endian;
+		};
+
+		reboot {
+			compatible = "brcm,brcmstb-reboot";
+			syscon = <&sun_top_ctrl 0x304 0x308>;
+		};
+
+		uart0: serial@406800 {
+			compatible = "ns16550a";
+			reg = <0x406800 0x20>;
+			reg-io-width = <0x4>;
+			reg-shift = <0x2>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <61>;
+			clocks = <&uart_clk>;
+			status = "disabled";
+		};
+
+		uart1: serial@406840 {
+			compatible = "ns16550a";
+			reg = <0x406840 0x20>;
+			reg-io-width = <0x4>;
+			reg-shift = <0x2>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <62>;
+			clocks = <&uart_clk>;
+			status = "disabled";
+		};
+
+		uart2: serial@406880 {
+			compatible = "ns16550a";
+			reg = <0x406880 0x20>;
+			reg-io-width = <0x4>;
+			reg-shift = <0x2>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <63>;
+			clocks = <&uart_clk>;
+			status = "disabled";
+		};
+
+		bsca: i2c@406200 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_irq0_intc>;
+		      reg = <0x406200 0x58>;
+		      interrupts = <24>;
+		      interrupt-names = "upg_bsca";
+		      status = "disabled";
+		};
+
+		bscb: i2c@406280 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_irq0_intc>;
+		      reg = <0x406280 0x58>;
+		      interrupts = <25>;
+		      interrupt-names = "upg_bscb";
+		      status = "disabled";
+		};
+
+		bscc: i2c@406300 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_irq0_intc>;
+		      reg = <0x406300 0x58>;
+		      interrupts = <26>;
+		      interrupt-names = "upg_bscc";
+		      status = "disabled";
+		};
+
+		bscd: i2c@408980 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_aon_irq0_intc>;
+		      reg = <0x408980 0x58>;
+		      interrupts = <27>;
+		      interrupt-names = "upg_bscd";
+		      status = "disabled";
+		};
+
+		pwma: pwm@406400 {
+			compatible = "brcm,bcm7038-pwm";
+			reg = <0x406400 0x28>;
+			#pwm-cells = <2>;
+			clocks = <&upg_clk>;
+			status = "disabled";
+		};
+
+		watchdog: watchdog@4066a8 {
+			clocks = <&upg_clk>;
+			compatible = "brcm,bcm7038-wdt";
+			reg = <0x4066a8 0x14>;
+			status = "disabled";
+		};
+
+		aon_pm_l2_intc: interrupt-controller@408440 {
+			compatible = "brcm,l2-intc";
+			reg = <0x408440 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <50>;
+			brcm,irq-can-wake;
+		};
+
+		aon_ctrl: syscon@408000 {
+			compatible = "brcm,brcmstb-aon-ctrl";
+			reg = <0x408000 0x100>, <0x408200 0x200>;
+			reg-names = "aon-ctrl", "aon-sram";
+		};
+
+		timers: timer@406680 {
+			compatible = "brcm,brcmstb-timers";
+			reg = <0x406680 0x40>;
+		};
+
+		upg_gio: gpio@406500 {
+			compatible = "brcm,brcmstb-gpio";
+			reg = <0x406500 0xa0>;
+			#gpio-cells = <2>;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			interrupt-controller;
+			interrupt-parent = <&upg_irq0_intc>;
+			interrupts = <6>;
+			brcm,gpio-bank-widths = <32 32 32 29 4>;
+		};
+
+		upg_gio_aon: gpio@408c00 {
+			compatible = "brcm,brcmstb-gpio";
+			reg = <0x408c00 0x60>;
+			#gpio-cells = <2>;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			interrupt-controller;
+			interrupt-parent = <&upg_aon_irq0_intc>;
+			interrupts = <6>;
+			interrupts-extended = <&upg_aon_irq0_intc 6>,
+					      <&aon_pm_l2_intc 5>;
+			wakeup-source;
+			brcm,gpio-bank-widths = <21 32 2>;
+		};
+
+		enet0: ethernet@430000 {
+			phy-mode = "internal";
+			phy-handle = <&phy1>;
+			mac-address = [ 00 10 18 36 23 1a ];
+			compatible = "brcm,genet-v2";
+			#address-cells = <0x1>;
+			#size-cells = <0x1>;
+			reg = <0x430000 0x4c8c>;
+			interrupts = <24>, <25>;
+			interrupt-parent = <&periph_intc>;
+			status = "disabled";
+
+			mdio@e14 {
+				compatible = "brcm,genet-mdio-v2";
+				#address-cells = <0x1>;
+				#size-cells = <0x0>;
+				reg = <0xe14 0x8>;
+
+				phy1: ethernet-phy@1 {
+					max-speed = <100>;
+					reg = <0x1>;
+					compatible = "brcm,40nm-ephy",
+						"ethernet-phy-ieee802.3-c22";
+				};
+			};
+		};
+
+		ehci0: usb@480300 {
+			compatible = "brcm,bcm7360-ehci", "generic-ehci";
+			reg = <0x480300 0x100>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <65>;
+			status = "disabled";
+		};
+
+		ohci0: usb@480400 {
+			compatible = "brcm,bcm7360-ohci", "generic-ohci";
+			reg = <0x480400 0x100>;
+			native-endian;
+			no-big-frame-no;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <66>;
+			status = "disabled";
+		};
+
+		hif_l2_intc: interrupt-controller@411000 {
+			compatible = "brcm,l2-intc";
+			reg = <0x411000 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <30>;
+		};
+
+		nand: nand@412800 {
+			compatible = "brcm,brcmnand-v5.0", "brcm,brcmnand";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg-names = "nand";
+			reg = <0x412800 0x400>;
+			interrupt-parent = <&hif_l2_intc>;
+			interrupts = <24>;
+			status = "disabled";
+		};
+
+		sata: sata@181000 {
+			compatible = "brcm,bcm7425-ahci", "brcm,sata3-ahci";
+			reg-names = "ahci", "top-ctrl";
+			reg = <0x181000 0xa9c>, <0x180020 0x1c>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <86>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sata0: sata-port@0 {
+				reg = <0>;
+				phys = <&sata_phy0>;
+			};
+
+			sata1: sata-port@1 {
+				reg = <1>;
+				phys = <&sata_phy1>;
+			};
+		};
+
+		sata_phy: sata-phy@180100 {
+			compatible = "brcm,bcm7425-sata-phy", "brcm,phy-sata3";
+			reg = <0x180100 0x0eff>;
+			reg-names = "phy";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sata_phy0: sata-phy@0 {
+				reg = <0>;
+				#phy-cells = <0>;
+			};
+
+			sata_phy1: sata-phy@1 {
+				reg = <1>;
+				#phy-cells = <0>;
+			};
+		};
+
+		sdhci0: sdhci@410000 {
+			compatible = "brcm,bcm7425-sdhci";
+			reg = <0x410000 0x100>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <82>;
+			status = "disabled";
+		};
+
+		spi_l2_intc: interrupt-controller@411d00 {
+			compatible = "brcm,l2-intc";
+			reg = <0x411d00 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <31>;
+		};
+
+		qspi: spi@413000 {
+			#address-cells = <0x1>;
+			#size-cells = <0x0>;
+			compatible = "brcm,spi-bcm-qspi",
+				     "brcm,spi-brcmstb-qspi";
+			clocks = <&upg_clk>;
+			reg = <0x410920 0x4 0x413200 0x188 0x413000 0x50>;
+			reg-names = "cs_reg", "hif_mspi", "bspi";
+			interrupts = <0x0 0x1 0x2 0x3 0x4 0x5 0x6>;
+			interrupt-parent = <&spi_l2_intc>;
+			interrupt-names = "spi_lr_fullness_reached",
+					  "spi_lr_session_aborted",
+					  "spi_lr_impatient",
+					  "spi_lr_session_done",
+					  "spi_lr_overread",
+					  "mspi_done",
+					  "mspi_halted";
+			status = "disabled";
+		};
+
+		mspi: spi@408a00 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,spi-bcm-qspi",
+				     "brcm,spi-brcmstb-mspi";
+			clocks = <&upg_clk>;
+			reg = <0x408a00 0x180>;
+			reg-names = "mspi";
+			interrupts = <0x14>;
+			interrupt-parent = <&upg_aon_irq0_intc>;
+			interrupt-names = "mspi_done";
+			status = "disabled";
+		};
+
+		waketimer: waketimer@408e80 {
+			compatible = "brcm,brcmstb-waketimer";
+			reg = <0x408e80 0x14>;
+			interrupts = <0x3>;
+			interrupt-parent = <&aon_pm_l2_intc>;
+			interrupt-names = "timer";
+			clocks = <&upg_clk>;
+			status = "disabled";
+		};
+	};
+
+	memory_controllers {
+		compatible = "simple-bus";
+		ranges = <0x0 0x103b0000 0xa000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		memory-controller@0 {
+			compatible = "brcm,brcmstb-memc", "simple-bus";
+			ranges = <0x0 0x0 0xa000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			memc-arb@1000 {
+				compatible = "brcm,brcmstb-memc-arb";
+				reg = <0x1000 0x248>;
+			};
+
+			memc-ddr@2000 {
+				compatible = "brcm,brcmstb-memc-ddr";
+				reg = <0x2000 0x300>;
+			};
+
+			ddr-phy@6000 {
+				compatible = "brcm,brcmstb-ddr-phy";
+				reg = <0x6000 0xc8>;
+			};
+
+			shimphy@8000 {
+				compatible = "brcm,brcmstb-ddr-shimphy";
+				reg = <0x8000 0x13c>;
+			};
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/brcm/bcm7362.dtsi b/arch/mips/boot/dts/brcm/bcm7362.dtsi
new file mode 100644
index 000000000..728b9e9f8
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm7362.dtsi
@@ -0,0 +1,464 @@
+// SPDX-License-Identifier: GPL-2.0
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "brcm,bcm7362";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mips-hpt-frequency = <375000000>;
+
+		cpu@0 {
+			compatible = "brcm,bmips4380";
+			device_type = "cpu";
+			reg = <0>;
+		};
+
+		cpu@1 {
+			compatible = "brcm,bmips4380";
+			device_type = "cpu";
+			reg = <1>;
+		};
+	};
+
+	aliases {
+		uart0 = &uart0;
+	};
+
+	cpu_intc: interrupt-controller {
+		#address-cells = <0>;
+		compatible = "mti,cpu-interrupt-controller";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+
+	clocks {
+		uart_clk: uart_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <81000000>;
+		};
+
+		upg_clk: upg_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <27000000>;
+		};
+	};
+
+	rdb {
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		compatible = "simple-bus";
+		ranges = <0 0x10000000 0x01000000>;
+
+		periph_intc: interrupt-controller@411400 {
+			compatible = "brcm,bcm7038-l1-intc";
+			reg = <0x411400 0x30>, <0x411600 0x30>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&cpu_intc>;
+			interrupts = <2>, <3>;
+		};
+
+		sun_l2_intc: interrupt-controller@403000 {
+			compatible = "brcm,l2-intc";
+			reg = <0x403000 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <48>;
+		};
+
+		gisb-arb@400000 {
+			compatible = "brcm,bcm7400-gisb-arb";
+			reg = <0x400000 0xdc>;
+			native-endian;
+			interrupt-parent = <&sun_l2_intc>;
+			interrupts = <0>, <2>;
+			brcm,gisb-arb-master-mask = <0x2f3>;
+			brcm,gisb-arb-master-names = "ssp_0", "cpu_0", "bsp_0",
+						     "rdc_0", "raaga_0",
+						     "avd_0", "jtag_0";
+		};
+
+		upg_irq0_intc: interrupt-controller@406600 {
+			compatible = "brcm,bcm7120-l2-intc";
+			reg = <0x406600 0x8>;
+
+			brcm,int-map-mask = <0x44>, <0x7000000>;
+			brcm,int-fwd-mask = <0x70000>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <56>, <54>;
+			interrupt-names = "upg_main", "upg_bsc";
+		};
+
+		upg_aon_irq0_intc: interrupt-controller@408b80 {
+			compatible = "brcm,bcm7120-l2-intc";
+			reg = <0x408b80 0x8>;
+
+			brcm,int-map-mask = <0x40>, <0x8000000>, <0x100000>;
+			brcm,int-fwd-mask = <0>;
+			brcm,irq-can-wake;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <57>, <55>, <59>;
+			interrupt-names = "upg_main_aon", "upg_bsc_aon",
+					  "upg_spi";
+		};
+
+		sun_top_ctrl: syscon@404000 {
+			compatible = "brcm,bcm7362-sun-top-ctrl", "syscon";
+			reg = <0x404000 0x51c>;
+			native-endian;
+		};
+
+		reboot {
+			compatible = "brcm,brcmstb-reboot";
+			syscon = <&sun_top_ctrl 0x304 0x308>;
+		};
+
+		uart0: serial@406800 {
+			compatible = "ns16550a";
+			reg = <0x406800 0x20>;
+			reg-io-width = <0x4>;
+			reg-shift = <0x2>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <61>;
+			clocks = <&uart_clk>;
+			status = "disabled";
+		};
+
+		uart1: serial@406840 {
+			compatible = "ns16550a";
+			reg = <0x406840 0x20>;
+			reg-io-width = <0x4>;
+			reg-shift = <0x2>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <62>;
+			clocks = <&uart_clk>;
+			status = "disabled";
+		};
+
+		uart2: serial@406880 {
+			compatible = "ns16550a";
+			reg = <0x406880 0x20>;
+			reg-io-width = <0x4>;
+			reg-shift = <0x2>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <63>;
+			clocks = <&uart_clk>;
+			status = "disabled";
+		};
+
+		bsca: i2c@406200 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_irq0_intc>;
+		      reg = <0x406200 0x58>;
+		      interrupts = <24>;
+		      interrupt-names = "upg_bsca";
+		      status = "disabled";
+		};
+
+		bscb: i2c@406280 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_irq0_intc>;
+		      reg = <0x406280 0x58>;
+		      interrupts = <25>;
+		      interrupt-names = "upg_bscb";
+		      status = "disabled";
+		};
+
+		bscd: i2c@408980 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_aon_irq0_intc>;
+		      reg = <0x408980 0x58>;
+		      interrupts = <27>;
+		      interrupt-names = "upg_bscd";
+		      status = "disabled";
+		};
+
+		pwma: pwm@406400 {
+			compatible = "brcm,bcm7038-pwm";
+			reg = <0x406400 0x28>;
+			#pwm-cells = <2>;
+			clocks = <&upg_clk>;
+			status = "disabled";
+		};
+
+		watchdog: watchdog@4066a8 {
+			clocks = <&upg_clk>;
+			compatible = "brcm,bcm7038-wdt";
+			reg = <0x4066a8 0x14>;
+			status = "disabled";
+		};
+
+		aon_pm_l2_intc: interrupt-controller@408440 {
+			compatible = "brcm,l2-intc";
+			reg = <0x408440 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <50>;
+			brcm,irq-can-wake;
+		};
+
+		aon_ctrl: syscon@408000 {
+			compatible = "brcm,brcmstb-aon-ctrl";
+			reg = <0x408000 0x100>, <0x408200 0x200>;
+			reg-names = "aon-ctrl", "aon-sram";
+		};
+
+		timers: timer@406680 {
+			compatible = "brcm,brcmstb-timers";
+			reg = <0x406680 0x40>;
+		};
+
+		upg_gio: gpio@406500 {
+			compatible = "brcm,brcmstb-gpio";
+			reg = <0x406500 0xa0>;
+			#gpio-cells = <2>;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			interrupt-controller;
+			interrupt-parent = <&upg_irq0_intc>;
+			interrupts = <6>;
+			brcm,gpio-bank-widths = <32 32 32 29 4>;
+		};
+
+		upg_gio_aon: gpio@408c00 {
+			compatible = "brcm,brcmstb-gpio";
+			reg = <0x408c00 0x60>;
+			#gpio-cells = <2>;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			interrupt-controller;
+			interrupt-parent = <&upg_aon_irq0_intc>;
+			interrupts = <6>;
+			interrupts-extended = <&upg_aon_irq0_intc 6>,
+					      <&aon_pm_l2_intc 5>;
+			wakeup-source;
+			brcm,gpio-bank-widths = <21 32 2>;
+		};
+
+		enet0: ethernet@430000 {
+			phy-mode = "internal";
+			phy-handle = <&phy1>;
+			mac-address = [ 00 10 18 36 23 1a ];
+			compatible = "brcm,genet-v2";
+			#address-cells = <0x1>;
+			#size-cells = <0x1>;
+			reg = <0x430000 0x4c8c>;
+			interrupts = <24>, <25>;
+			interrupt-parent = <&periph_intc>;
+			status = "disabled";
+
+			mdio@e14 {
+				compatible = "brcm,genet-mdio-v2";
+				#address-cells = <0x1>;
+				#size-cells = <0x0>;
+				reg = <0xe14 0x8>;
+
+				phy1: ethernet-phy@1 {
+					max-speed = <100>;
+					reg = <0x1>;
+					compatible = "brcm,40nm-ephy",
+						"ethernet-phy-ieee802.3-c22";
+				};
+			};
+		};
+
+		ehci0: usb@480300 {
+			compatible = "brcm,bcm7362-ehci", "generic-ehci";
+			reg = <0x480300 0x100>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <65>;
+			status = "disabled";
+		};
+
+		ohci0: usb@480400 {
+			compatible = "brcm,bcm7362-ohci", "generic-ohci";
+			reg = <0x480400 0x100>;
+			native-endian;
+			no-big-frame-no;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <66>;
+			status = "disabled";
+		};
+
+		hif_l2_intc: interrupt-controller@411000 {
+			compatible = "brcm,l2-intc";
+			reg = <0x411000 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <30>;
+		};
+
+		nand: nand@412800 {
+			compatible = "brcm,brcmnand-v5.0", "brcm,brcmnand";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg-names = "nand";
+			reg = <0x412800 0x400>;
+			interrupt-parent = <&hif_l2_intc>;
+			interrupts = <24>;
+			status = "disabled";
+		};
+
+		sata: sata@181000 {
+			compatible = "brcm,bcm7425-ahci", "brcm,sata3-ahci";
+			reg-names = "ahci", "top-ctrl";
+			reg = <0x181000 0xa9c>, <0x180020 0x1c>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <86>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sata0: sata-port@0 {
+				reg = <0>;
+				phys = <&sata_phy0>;
+			};
+
+			sata1: sata-port@1 {
+				reg = <1>;
+				phys = <&sata_phy1>;
+			};
+		};
+
+		sata_phy: sata-phy@180100 {
+			compatible = "brcm,bcm7425-sata-phy", "brcm,phy-sata3";
+			reg = <0x180100 0x0eff>;
+			reg-names = "phy";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sata_phy0: sata-phy@0 {
+				reg = <0>;
+				#phy-cells = <0>;
+			};
+
+			sata_phy1: sata-phy@1 {
+				reg = <1>;
+				#phy-cells = <0>;
+			};
+		};
+
+		sdhci0: sdhci@410000 {
+			compatible = "brcm,bcm7425-sdhci";
+			reg = <0x410000 0x100>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <82>;
+			status = "disabled";
+		};
+
+		spi_l2_intc: interrupt-controller@411d00 {
+			compatible = "brcm,l2-intc";
+			reg = <0x411d00 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <31>;
+		};
+
+		qspi: spi@413000 {
+			#address-cells = <0x1>;
+			#size-cells = <0x0>;
+			compatible = "brcm,spi-bcm-qspi",
+				     "brcm,spi-brcmstb-qspi";
+			clocks = <&upg_clk>;
+			reg = <0x410920 0x4 0x413200 0x188 0x413000 0x50>;
+			reg-names = "cs_reg", "hif_mspi", "bspi";
+			interrupts = <0x0 0x1 0x2 0x3 0x4 0x5 0x6>;
+			interrupt-parent = <&spi_l2_intc>;
+			interrupt-names = "spi_lr_fullness_reached",
+					  "spi_lr_session_aborted",
+					  "spi_lr_impatient",
+					  "spi_lr_session_done",
+					  "spi_lr_overread",
+					  "mspi_done",
+					  "mspi_halted";
+			status = "disabled";
+		};
+
+		mspi: spi@408a00 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,spi-bcm-qspi",
+				     "brcm,spi-brcmstb-mspi";
+			clocks = <&upg_clk>;
+			reg = <0x408a00 0x180>;
+			reg-names = "mspi";
+			interrupts = <0x14>;
+			interrupt-parent = <&upg_aon_irq0_intc>;
+			interrupt-names = "mspi_done";
+			status = "disabled";
+		};
+
+		waketimer: waketimer@408e80 {
+			compatible = "brcm,brcmstb-waketimer";
+			reg = <0x408e80 0x14>;
+			interrupts = <0x3>;
+			interrupt-parent = <&aon_pm_l2_intc>;
+			interrupt-names = "timer";
+			clocks = <&upg_clk>;
+			status = "disabled";
+		};
+	};
+
+	memory_controllers {
+		compatible = "simple-bus";
+		ranges = <0x0 0x103b0000 0xa000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		memory-controller@0 {
+			compatible = "brcm,brcmstb-memc", "simple-bus";
+			ranges = <0x0 0x0 0xa000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			memc-arb@1000 {
+				compatible = "brcm,brcmstb-memc-arb";
+				reg = <0x1000 0x248>;
+			};
+
+			memc-ddr@2000 {
+				compatible = "brcm,brcmstb-memc-ddr";
+				reg = <0x2000 0x300>;
+			};
+
+			ddr-phy@6000 {
+				compatible = "brcm,brcmstb-ddr-phy";
+				reg = <0x6000 0xc8>;
+			};
+
+			shimphy@8000 {
+				compatible = "brcm,brcmstb-ddr-shimphy";
+				reg = <0x8000 0x13c>;
+			};
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/brcm/bcm7420.dtsi b/arch/mips/boot/dts/brcm/bcm7420.dtsi
new file mode 100644
index 000000000..9540c27f1
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm7420.dtsi
@@ -0,0 +1,342 @@
+// SPDX-License-Identifier: GPL-2.0
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "brcm,bcm7420";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mips-hpt-frequency = <93750000>;
+
+		cpu@0 {
+			compatible = "brcm,bmips5000";
+			device_type = "cpu";
+			reg = <0>;
+		};
+
+		cpu@1 {
+			compatible = "brcm,bmips5000";
+			device_type = "cpu";
+			reg = <1>;
+		};
+	};
+
+	aliases {
+		uart0 = &uart0;
+	};
+
+	cpu_intc: interrupt-controller {
+		#address-cells = <0>;
+		compatible = "mti,cpu-interrupt-controller";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+
+	clocks {
+		uart_clk: uart_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <81000000>;
+		};
+
+		upg_clk: upg_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <27000000>;
+		};
+	};
+
+	rdb {
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		compatible = "simple-bus";
+		ranges = <0 0x10000000 0x01000000>;
+
+		periph_intc: interrupt-controller@441400 {
+			compatible = "brcm,bcm7038-l1-intc";
+			reg = <0x441400 0x30>, <0x441600 0x30>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&cpu_intc>;
+			interrupts = <2>, <3>;
+		};
+
+		sun_l2_intc: interrupt-controller@401800 {
+			compatible = "brcm,l2-intc";
+			reg = <0x401800 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <23>;
+		};
+
+		gisb-arb@400000 {
+			compatible = "brcm,bcm7400-gisb-arb";
+			reg = <0x400000 0xdc>;
+			native-endian;
+			interrupt-parent = <&sun_l2_intc>;
+			interrupts = <0>, <2>;
+			brcm,gisb-arb-master-mask = <0x3ff>;
+			brcm,gisb-arb-master-names = "ssp_0", "cpu_0", "pci_0",
+						     "pcie_0", "bsp_0", "rdc_0",
+						     "rptd_0", "avd_0", "avd_1",
+						     "jtag_0";
+		};
+
+		upg_irq0_intc: interrupt-controller@406780 {
+			compatible = "brcm,bcm7120-l2-intc";
+			reg = <0x406780 0x8>;
+
+			brcm,int-map-mask = <0x44>, <0x1f000000>, <0x100000>;
+			brcm,int-fwd-mask = <0x70000>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <18>, <19>, <20>;
+			interrupt-names = "upg_main", "upg_bsc", "upg_spi";
+		};
+
+		sun_top_ctrl: syscon@404000 {
+			compatible = "brcm,bcm7420-sun-top-ctrl", "syscon";
+			reg = <0x404000 0x60c>;
+			native-endian;
+		};
+
+		reboot {
+			compatible = "brcm,bcm7038-reboot";
+			syscon = <&sun_top_ctrl 0x8 0x14>;
+		};
+
+		uart0: serial@406b00 {
+			compatible = "ns16550a";
+			reg = <0x406b00 0x20>;
+			reg-io-width = <0x4>;
+			reg-shift = <0x2>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <21>;
+			clocks = <&uart_clk>;
+			status = "disabled";
+		};
+
+		uart1: serial@406b40 {
+			compatible = "ns16550a";
+			reg = <0x406b40 0x20>;
+			reg-io-width = <0x4>;
+			reg-shift = <0x2>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <64>;
+			clocks = <&uart_clk>;
+			status = "disabled";
+		};
+
+		uart2: serial@406b80 {
+			compatible = "ns16550a";
+			reg = <0x406b80 0x20>;
+			reg-io-width = <0x4>;
+			reg-shift = <0x2>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <65>;
+			clocks = <&uart_clk>;
+			status = "disabled";
+		};
+
+		bsca: i2c@406200 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_irq0_intc>;
+		      reg = <0x406200 0x58>;
+		      interrupts = <24>;
+		      interrupt-names = "upg_bsca";
+		      status = "disabled";
+		};
+
+		bscb: i2c@406280 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_irq0_intc>;
+		      reg = <0x406280 0x58>;
+		      interrupts = <25>;
+		      interrupt-names = "upg_bscb";
+		      status = "disabled";
+		};
+
+		bscc: i2c@406300 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_irq0_intc>;
+		      reg = <0x406300 0x58>;
+		      interrupts = <26>;
+		      interrupt-names = "upg_bscc";
+		      status = "disabled";
+		};
+
+		bscd: i2c@406380 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_irq0_intc>;
+		      reg = <0x406380 0x58>;
+		      interrupts = <27>;
+		      interrupt-names = "upg_bscd";
+		      status = "disabled";
+		};
+
+		bsce: i2c@406800 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_irq0_intc>;
+		      reg = <0x406800 0x58>;
+		      interrupts = <28>;
+		      interrupt-names = "upg_bsce";
+		      status = "disabled";
+		};
+
+		pwma: pwm@406580 {
+			compatible = "brcm,bcm7038-pwm";
+			reg = <0x406580 0x28>;
+			#pwm-cells = <2>;
+			clocks = <&upg_clk>;
+			status = "disabled";
+		};
+
+		pwmb: pwm@406880 {
+			compatible = "brcm,bcm7038-pwm";
+			reg = <0x406880 0x28>;
+			#pwm-cells = <2>;
+			clocks = <&upg_clk>;
+			status = "disabled";
+		};
+
+		watchdog: watchdog@4067e8 {
+			clocks = <&upg_clk>;
+			compatible = "brcm,bcm7038-wdt";
+			reg = <0x4067e8 0x14>;
+			status = "disabled";
+		};
+
+		upg_gio: gpio@406700 {
+			compatible = "brcm,brcmstb-gpio";
+			reg = <0x406700 0x80>;
+			#gpio-cells = <2>;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			interrupt-controller;
+			interrupt-parent = <&upg_irq0_intc>;
+			interrupts = <6>;
+			brcm,gpio-bank-widths = <32 32 32 27>;
+		};
+
+		enet0: ethernet@468000 {
+			phy-mode = "internal";
+			phy-handle = <&phy1>;
+			mac-address = [ 00 10 18 36 23 1a ];
+			compatible = "brcm,genet-v1";
+			#address-cells = <0x1>;
+			#size-cells = <0x1>;
+			reg = <0x468000 0x3c8c>;
+			interrupts = <69>, <79>;
+			interrupt-parent = <&periph_intc>;
+			status = "disabled";
+
+			mdio@e14 {
+				compatible = "brcm,genet-mdio-v1";
+				#address-cells = <0x1>;
+				#size-cells = <0x0>;
+				reg = <0xe14 0x8>;
+
+				phy1: ethernet-phy@1 {
+					max-speed = <100>;
+					reg = <0x1>;
+					compatible = "brcm,65nm-ephy",
+						"ethernet-phy-ieee802.3-c22";
+				};
+			};
+		};
+
+		ehci0: usb@488300 {
+			compatible = "brcm,bcm7420-ehci", "generic-ehci";
+			reg = <0x488300 0x100>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <60>;
+			status = "disabled";
+		};
+
+		ohci0: usb@488400 {
+			compatible = "brcm,bcm7420-ohci", "generic-ohci";
+			reg = <0x488400 0x100>;
+			native-endian;
+			no-big-frame-no;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <61>;
+			status = "disabled";
+		};
+
+		ehci1: usb@488500 {
+			compatible = "brcm,bcm7420-ehci", "generic-ehci";
+			reg = <0x488500 0x100>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <55>;
+			status = "disabled";
+		};
+
+		ohci1: usb@488600 {
+			compatible = "brcm,bcm7420-ohci", "generic-ohci";
+			reg = <0x488600 0x100>;
+			native-endian;
+			no-big-frame-no;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <62>;
+			status = "disabled";
+		};
+
+		spi_l2_intc: interrupt-controller@411d00 {
+			compatible = "brcm,l2-intc";
+			reg = <0x411d00 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <78>;
+		};
+
+		qspi: spi@443000 {
+			#address-cells = <0x1>;
+			#size-cells = <0x0>;
+			compatible = "brcm,spi-bcm-qspi",
+				     "brcm,spi-brcmstb-qspi";
+			clocks = <&upg_clk>;
+			reg = <0x440920 0x4 0x443200 0x188 0x443000 0x50>;
+			reg-names = "cs_reg", "hif_mspi", "bspi";
+			interrupts = <0x0 0x1 0x2 0x3 0x4 0x5 0x6>;
+			interrupt-parent = <&spi_l2_intc>;
+			interrupt-names = "spi_lr_fullness_reached",
+					  "spi_lr_session_aborted",
+					  "spi_lr_impatient",
+					  "spi_lr_session_done",
+					  "spi_lr_overread",
+					  "mspi_done",
+					  "mspi_halted";
+			status = "disabled";
+		};
+
+		mspi: spi@406400 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,spi-bcm-qspi",
+				     "brcm,spi-brcmstb-mspi";
+			clocks = <&upg_clk>;
+			reg = <0x406400 0x180>;
+			reg-names = "mspi";
+			interrupts = <0x14>;
+			interrupt-parent = <&upg_irq0_intc>;
+			interrupt-names = "mspi_done";
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/brcm/bcm7425.dtsi b/arch/mips/boot/dts/brcm/bcm7425.dtsi
new file mode 100644
index 000000000..62588c53d
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm7425.dtsi
@@ -0,0 +1,617 @@
+// SPDX-License-Identifier: GPL-2.0
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "brcm,bcm7425";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mips-hpt-frequency = <163125000>;
+
+		cpu@0 {
+			compatible = "brcm,bmips5000";
+			device_type = "cpu";
+			reg = <0>;
+		};
+
+		cpu@1 {
+			compatible = "brcm,bmips5000";
+			device_type = "cpu";
+			reg = <1>;
+		};
+	};
+
+	aliases {
+		uart0 = &uart0;
+	};
+
+	cpu_intc: interrupt-controller {
+		#address-cells = <0>;
+		compatible = "mti,cpu-interrupt-controller";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+
+	clocks {
+		uart_clk: uart_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <81000000>;
+		};
+
+		upg_clk: upg_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <27000000>;
+		};
+	};
+
+	rdb {
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		compatible = "simple-bus";
+		ranges = <0 0x10000000 0x01000000>;
+
+		periph_intc: interrupt-controller@41a400 {
+			compatible = "brcm,bcm7038-l1-intc";
+			reg = <0x41a400 0x30>, <0x41a600 0x30>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&cpu_intc>;
+			interrupts = <2>, <3>;
+		};
+
+		sun_l2_intc: interrupt-controller@403000 {
+			compatible = "brcm,l2-intc";
+			reg = <0x403000 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <47>;
+		};
+
+		gisb-arb@400000 {
+			compatible = "brcm,bcm7400-gisb-arb";
+			reg = <0x400000 0xdc>;
+			native-endian;
+			interrupt-parent = <&sun_l2_intc>;
+			interrupts = <0>, <2>;
+			brcm,gisb-arb-master-mask = <0x177b>;
+			brcm,gisb-arb-master-names = "ssp_0", "cpu_0", "pcie_0",
+						     "bsp_0", "rdc_0",
+						     "raaga_0", "avd_1",
+						     "jtag_0", "svd_0",
+						     "vice_0";
+		};
+
+		upg_irq0_intc: interrupt-controller@406780 {
+			compatible = "brcm,bcm7120-l2-intc";
+			reg = <0x406780 0x8>;
+
+			brcm,int-map-mask = <0x44>, <0x7000000>;
+			brcm,int-fwd-mask = <0x70000>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <55>, <53>;
+			interrupt-names = "upg_main", "upg_bsc";
+		};
+
+		upg_aon_irq0_intc: interrupt-controller@409480 {
+			compatible = "brcm,bcm7120-l2-intc";
+			reg = <0x409480 0x8>;
+
+			brcm,int-map-mask = <0x40>, <0x18000000>, <0x100000>;
+			brcm,int-fwd-mask = <0>;
+			brcm,irq-can-wake;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <56>, <54>, <59>;
+			interrupt-names = "upg_main_aon", "upg_bsc_aon",
+					  "upg_spi";
+		};
+
+		sun_top_ctrl: syscon@404000 {
+			compatible = "brcm,bcm7425-sun-top-ctrl", "syscon";
+			reg = <0x404000 0x51c>;
+			native-endian;
+		};
+
+		reboot {
+			compatible = "brcm,brcmstb-reboot";
+			syscon = <&sun_top_ctrl 0x304 0x308>;
+		};
+
+		uart0: serial@406b00 {
+			compatible = "ns16550a";
+			reg = <0x406b00 0x20>;
+			reg-io-width = <0x4>;
+			reg-shift = <0x2>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <61>;
+			clocks = <&uart_clk>;
+			status = "disabled";
+		};
+
+		uart1: serial@406b40 {
+			compatible = "ns16550a";
+			reg = <0x406b40 0x20>;
+			reg-io-width = <0x4>;
+			reg-shift = <0x2>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <62>;
+			clocks = <&uart_clk>;
+			status = "disabled";
+		};
+
+		uart2: serial@406b80 {
+			compatible = "ns16550a";
+			reg = <0x406b80 0x20>;
+			reg-io-width = <0x4>;
+			reg-shift = <0x2>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <63>;
+			clocks = <&uart_clk>;
+			status = "disabled";
+		};
+
+		bsca: i2c@409180 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_aon_irq0_intc>;
+		      reg = <0x409180 0x58>;
+		      interrupts = <27>;
+		      interrupt-names = "upg_bsca";
+		      status = "disabled";
+		};
+
+		bscb: i2c@409400 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_aon_irq0_intc>;
+		      reg = <0x409400 0x58>;
+		      interrupts = <28>;
+		      interrupt-names = "upg_bscb";
+		      status = "disabled";
+		};
+
+		bscc: i2c@406200 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_irq0_intc>;
+		      reg = <0x406200 0x58>;
+		      interrupts = <24>;
+		      interrupt-names = "upg_bscc";
+		      status = "disabled";
+		};
+
+		bscd: i2c@406280 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_irq0_intc>;
+		      reg = <0x406280 0x58>;
+		      interrupts = <25>;
+		      interrupt-names = "upg_bscd";
+		      status = "disabled";
+		};
+
+		bsce: i2c@406300 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_irq0_intc>;
+		      reg = <0x406300 0x58>;
+		      interrupts = <26>;
+		      interrupt-names = "upg_bsce";
+		      status = "disabled";
+		};
+
+		pwma: pwm@406580 {
+			compatible = "brcm,bcm7038-pwm";
+			reg = <0x406580 0x28>;
+			#pwm-cells = <2>;
+			clocks = <&upg_clk>;
+			status = "disabled";
+		};
+
+		pwmb: pwm@406800 {
+			compatible = "brcm,bcm7038-pwm";
+			reg = <0x406800 0x28>;
+			#pwm-cells = <2>;
+			clocks = <&upg_clk>;
+			status = "disabled";
+		};
+
+		watchdog: watchdog@4067e8 {
+			clocks = <&upg_clk>;
+			compatible = "brcm,bcm7038-wdt";
+			reg = <0x4067e8 0x14>;
+			status = "disabled";
+		};
+
+		aon_pm_l2_intc: interrupt-controller@408440 {
+			compatible = "brcm,l2-intc";
+			reg = <0x408440 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <49>;
+			brcm,irq-can-wake;
+		};
+
+		aon_ctrl: syscon@408000 {
+			compatible = "brcm,brcmstb-aon-ctrl";
+			reg = <0x408000 0x100>, <0x408200 0x200>;
+			reg-names = "aon-ctrl", "aon-sram";
+		};
+
+		timers: timer@4067c0 {
+			compatible = "brcm,brcmstb-timers";
+			reg = <0x4067c0 0x40>;
+		};
+
+		upg_gio: gpio@406700 {
+			compatible = "brcm,brcmstb-gpio";
+			reg = <0x406700 0x80>;
+			#gpio-cells = <2>;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			interrupt-controller;
+			interrupt-parent = <&upg_irq0_intc>;
+			interrupts = <6>;
+			brcm,gpio-bank-widths = <32 32 32 21>;
+		};
+
+		upg_gio_aon: gpio@4094c0 {
+			compatible = "brcm,brcmstb-gpio";
+			reg = <0x4094c0 0x40>;
+			#gpio-cells = <2>;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			interrupt-controller;
+			interrupt-parent = <&upg_aon_irq0_intc>;
+			interrupts = <6>;
+			interrupts-extended = <&upg_aon_irq0_intc 6>,
+					      <&aon_pm_l2_intc 5>;
+			wakeup-source;
+			brcm,gpio-bank-widths = <18 4>;
+		};
+
+		enet0: ethernet@b80000 {
+			phy-mode = "internal";
+			phy-handle = <&phy1>;
+			mac-address = [ 00 10 18 36 23 1a ];
+			compatible = "brcm,genet-v3";
+			#address-cells = <0x1>;
+			#size-cells = <0x1>;
+			reg = <0xb80000 0x11c88>;
+			interrupts = <17>, <18>;
+			interrupt-parent = <&periph_intc>;
+			status = "disabled";
+
+			mdio@e14 {
+				compatible = "brcm,genet-mdio-v3";
+				#address-cells = <0x1>;
+				#size-cells = <0x0>;
+				reg = <0xe14 0x8>;
+
+				phy1: ethernet-phy@1 {
+					max-speed = <100>;
+					reg = <0x1>;
+					compatible = "brcm,40nm-ephy",
+						"ethernet-phy-ieee802.3-c22";
+				};
+			};
+		};
+
+		ehci0: usb@480300 {
+			compatible = "brcm,bcm7425-ehci", "generic-ehci";
+			reg = <0x480300 0x100>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <65>;
+			status = "disabled";
+		};
+
+		ohci0: usb@480400 {
+			compatible = "brcm,bcm7425-ohci", "generic-ohci";
+			reg = <0x480400 0x100>;
+			native-endian;
+			no-big-frame-no;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <67>;
+			status = "disabled";
+		};
+
+		ehci1: usb@480500 {
+			compatible = "brcm,bcm7425-ehci", "generic-ehci";
+			reg = <0x480500 0x100>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <66>;
+			status = "disabled";
+		};
+
+		ohci1: usb@480600 {
+			compatible = "brcm,bcm7425-ohci", "generic-ohci";
+			reg = <0x480600 0x100>;
+			native-endian;
+			no-big-frame-no;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <68>;
+			status = "disabled";
+		};
+
+		ehci2: usb@490300 {
+			compatible = "brcm,bcm7425-ehci", "generic-ehci";
+			reg = <0x490300 0x100>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <70>;
+			status = "disabled";
+		};
+
+		ohci2: usb@490400 {
+			compatible = "brcm,bcm7425-ohci", "generic-ohci";
+			reg = <0x490400 0x100>;
+			native-endian;
+			no-big-frame-no;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <72>;
+			status = "disabled";
+		};
+
+		ehci3: usb@490500 {
+			compatible = "brcm,bcm7425-ehci", "generic-ehci";
+			reg = <0x490500 0x100>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <71>;
+			status = "disabled";
+		};
+
+		ohci3: usb@490600 {
+			compatible = "brcm,bcm7425-ohci", "generic-ohci";
+			reg = <0x490600 0x100>;
+			native-endian;
+			no-big-frame-no;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <73>;
+			status = "disabled";
+		};
+
+		hif_l2_intc: interrupt-controller@41a000 {
+			compatible = "brcm,l2-intc";
+			reg = <0x41a000 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <24>;
+		};
+
+		nand: nand@41b800 {
+			compatible = "brcm,brcmnand-v5.0", "brcm,brcmnand";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg-names = "nand", "flash-edu";
+			reg = <0x41b800 0x400>, <0x41bc00 0x24>;
+			interrupt-parent = <&hif_l2_intc>;
+			interrupts = <24>;
+			status = "disabled";
+		};
+
+		sata: sata@181000 {
+			compatible = "brcm,bcm7425-ahci", "brcm,sata3-ahci";
+			reg-names = "ahci", "top-ctrl";
+			reg = <0x181000 0xa9c>, <0x180020 0x1c>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <41>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sata0: sata-port@0 {
+				reg = <0>;
+				phys = <&sata_phy0>;
+			};
+
+			sata1: sata-port@1 {
+				reg = <1>;
+				phys = <&sata_phy1>;
+			};
+		};
+
+		sata_phy: sata-phy@180100 {
+			compatible = "brcm,bcm7425-sata-phy", "brcm,phy-sata3";
+			reg = <0x180100 0x0eff>;
+			reg-names = "phy";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sata_phy0: sata-phy@0 {
+				reg = <0>;
+				#phy-cells = <0>;
+			};
+
+			sata_phy1: sata-phy@1 {
+				reg = <1>;
+				#phy-cells = <0>;
+			};
+		};
+
+		sdhci0: sdhci@419000 {
+			compatible = "brcm,bcm7425-sdhci";
+			reg = <0x419000 0x100>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <43>;
+			sd-uhs-sdr50;
+			mmc-hs200-1_8v;
+			status = "disabled";
+		};
+
+		sdhci1: sdhci@419200 {
+			compatible = "brcm,bcm7425-sdhci";
+			reg = <0x419200 0x100>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <44>;
+			sd-uhs-sdr50;
+			mmc-hs200-1_8v;
+			status = "disabled";
+		};
+
+		spi_l2_intc: interrupt-controller@41ad00 {
+			compatible = "brcm,l2-intc";
+			reg = <0x41ad00 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <25>;
+		};
+
+		qspi: spi@41c000 {
+			#address-cells = <0x1>;
+			#size-cells = <0x0>;
+			compatible = "brcm,spi-bcm-qspi",
+				     "brcm,spi-brcmstb-qspi";
+			clocks = <&upg_clk>;
+			reg = <0x419920 0x4 0x41c200 0x188 0x41c000 0x50>;
+			reg-names = "cs_reg", "hif_mspi", "bspi";
+			interrupts = <0x0 0x1 0x2 0x3 0x4 0x5 0x6>;
+			interrupt-parent = <&spi_l2_intc>;
+			interrupt-names = "spi_lr_fullness_reached",
+					  "spi_lr_session_aborted",
+					  "spi_lr_impatient",
+					  "spi_lr_session_done",
+					  "spi_lr_overread",
+					  "mspi_done",
+					  "mspi_halted";
+			status = "disabled";
+		};
+
+		mspi: spi@409200 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,spi-bcm-qspi",
+				     "brcm,spi-brcmstb-mspi";
+			clocks = <&upg_clk>;
+			reg = <0x409200 0x180>;
+			reg-names = "mspi";
+			interrupts = <0x14>;
+			interrupt-parent = <&upg_aon_irq0_intc>;
+			interrupt-names = "mspi_done";
+			status = "disabled";
+		};
+
+		waketimer: waketimer@409580 {
+			compatible = "brcm,brcmstb-waketimer";
+			reg = <0x409580 0x14>;
+			interrupts = <0x3>;
+			interrupt-parent = <&aon_pm_l2_intc>;
+			interrupt-names = "timer";
+			clocks = <&upg_clk>;
+			status = "disabled";
+		};
+	};
+
+	memory_controllers {
+		compatible = "simple-bus";
+		ranges = <0x0 0x103b0000 0x1a000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		memory-controller@0 {
+			compatible = "brcm,brcmstb-memc", "simple-bus";
+			ranges = <0x0 0x0 0xa000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			memc-arb@1000 {
+				compatible = "brcm,brcmstb-memc-arb";
+				reg = <0x1000 0x248>;
+			};
+
+			memc-ddr@2000 {
+				compatible = "brcm,brcmstb-memc-ddr";
+				reg = <0x2000 0x300>;
+			};
+
+			ddr-phy@6000 {
+				compatible = "brcm,brcmstb-ddr-phy";
+				reg = <0x6000 0xc8>;
+			};
+
+			shimphy@8000 {
+				compatible = "brcm,brcmstb-ddr-shimphy";
+				reg = <0x8000 0x13c>;
+			};
+		};
+
+		memory-controller@1 {
+			compatible = "brcm,brcmstb-memc", "simple-bus";
+			ranges = <0x0 0x10000 0xa000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			memc-arb@1000 {
+				compatible = "brcm,brcmstb-memc-arb";
+				reg = <0x1000 0x248>;
+			};
+
+			memc-ddr@2000 {
+				compatible = "brcm,brcmstb-memc-ddr";
+				reg = <0x2000 0x300>;
+			};
+
+			ddr-phy@6000 {
+				compatible = "brcm,brcmstb-ddr-phy";
+				reg = <0x6000 0xc8>;
+			};
+
+			shimphy@8000 {
+				compatible = "brcm,brcmstb-ddr-shimphy";
+				reg = <0x8000 0x13c>;
+			};
+		};
+	};
+
+	pcie_0: pcie@8b20000 {
+		status = "disabled";
+		compatible = "brcm,bcm7425-pcie";
+
+		ranges = <0x02000000 0x0 0xd0000000 0xd0000000 0x0 0x08000000
+			  0x02000000 0x0 0xd8000000 0xd8000000 0x0 0x08000000
+			  0x02000000 0x0 0xe0000000 0xe0000000 0x0 0x08000000
+			  0x02000000 0x0 0xe8000000 0xe8000000 0x0 0x08000000>;
+
+		reg = <0x10410000 0x19310>;
+		aspm-no-l0s;
+		device_type = "pci";
+		msi-controller;
+		msi-parent = <&pcie_0>;
+		#address-cells = <0x3>;
+		#size-cells = <0x2>;
+		bus-range = <0x0 0xff>;
+		interrupt-map-mask = <0x0 0x0 0x0 0x7>;
+		linux,pci-domain = <0x0>;
+
+		interrupt-parent = <&periph_intc>;
+		interrupts = <37>, <37>;
+		interrupt-names = "pcie", "msi";
+		#interrupt-cells = <0x1>;
+		interrupt-map = <0 0 0 1 &periph_intc 0x21
+				 0 0 0 1 &periph_intc 0x22
+				 0 0 0 1 &periph_intc 0x23
+				 0 0 0 1 &periph_intc 0x24>;
+	};
+};
diff --git a/arch/mips/boot/dts/brcm/bcm7435.dtsi b/arch/mips/boot/dts/brcm/bcm7435.dtsi
new file mode 100644
index 000000000..8c001b944
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm7435.dtsi
@@ -0,0 +1,632 @@
+// SPDX-License-Identifier: GPL-2.0
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "brcm,bcm7435";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mips-hpt-frequency = <175625000>;
+
+		cpu@0 {
+			compatible = "brcm,bmips5200";
+			device_type = "cpu";
+			reg = <0>;
+		};
+
+		cpu@1 {
+			compatible = "brcm,bmips5200";
+			device_type = "cpu";
+			reg = <1>;
+		};
+
+		cpu@2 {
+			compatible = "brcm,bmips5200";
+			device_type = "cpu";
+			reg = <2>;
+		};
+
+		cpu@3 {
+			compatible = "brcm,bmips5200";
+			device_type = "cpu";
+			reg = <3>;
+		};
+	};
+
+	aliases {
+		uart0 = &uart0;
+	};
+
+	cpu_intc: interrupt-controller {
+		#address-cells = <0>;
+		compatible = "mti,cpu-interrupt-controller";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+
+	clocks {
+		uart_clk: uart_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <81000000>;
+		};
+
+		upg_clk: upg_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <27000000>;
+		};
+	};
+
+	rdb {
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		compatible = "simple-bus";
+		ranges = <0 0x10000000 0x01000000>;
+
+		periph_intc: interrupt-controller@41b500 {
+			compatible = "brcm,bcm7038-l1-intc";
+			reg = <0x41b500 0x40>, <0x41b600 0x40>,
+				<0x41b700 0x40>, <0x41b800 0x40>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&cpu_intc>;
+			interrupts = <2>, <3>, <2>, <3>;
+		};
+
+		sun_l2_intc: interrupt-controller@403000 {
+			compatible = "brcm,l2-intc";
+			reg = <0x403000 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <52>;
+		};
+
+		gisb-arb@400000 {
+			compatible = "brcm,bcm7435-gisb-arb";
+			reg = <0x400000 0xdc>;
+			native-endian;
+			interrupt-parent = <&sun_l2_intc>;
+			interrupts = <0>, <2>;
+			brcm,gisb-arb-master-mask = <0xf77f>;
+			brcm,gisb-arb-master-names = "ssp_0", "cpu_0", "webcpu_0",
+						     "pcie_0", "bsp_0",
+						     "rdc_0", "raaga_0",
+						     "avd_1", "jtag_0",
+						     "svd_0", "vice_0",
+						     "vice_1", "raaga_1",
+						     "scpu";
+		};
+
+		upg_irq0_intc: interrupt-controller@406780 {
+			compatible = "brcm,bcm7120-l2-intc";
+			reg = <0x406780 0x8>;
+
+			brcm,int-map-mask = <0x44>, <0x7000000>;
+			brcm,int-fwd-mask = <0x70000>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <60>, <58>;
+			interrupt-names = "upg_main", "upg_bsc";
+		};
+
+		upg_aon_irq0_intc: interrupt-controller@409480 {
+			compatible = "brcm,bcm7120-l2-intc";
+			reg = <0x409480 0x8>;
+
+			brcm,int-map-mask = <0x40>, <0x18000000>, <0x100000>;
+			brcm,int-fwd-mask = <0>;
+			brcm,irq-can-wake;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&periph_intc>;
+			interrupts = <61>, <59>, <64>;
+			interrupt-names = "upg_main_aon", "upg_bsc_aon",
+					  "upg_spi";
+		};
+
+		sun_top_ctrl: syscon@404000 {
+			compatible = "brcm,bcm7425-sun-top-ctrl", "syscon";
+			reg = <0x404000 0x51c>;
+			native-endian;
+		};
+
+		reboot {
+			compatible = "brcm,brcmstb-reboot";
+			syscon = <&sun_top_ctrl 0x304 0x308>;
+		};
+
+		uart0: serial@406b00 {
+			compatible = "ns16550a";
+			reg = <0x406b00 0x20>;
+			reg-io-width = <0x4>;
+			reg-shift = <0x2>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <66>;
+			clocks = <&uart_clk>;
+			status = "disabled";
+		};
+
+		uart1: serial@406b40 {
+			compatible = "ns16550a";
+			reg = <0x406b40 0x20>;
+			reg-io-width = <0x4>;
+			reg-shift = <0x2>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <67>;
+			clocks = <&uart_clk>;
+			status = "disabled";
+		};
+
+		uart2: serial@406b80 {
+			compatible = "ns16550a";
+			reg = <0x406b80 0x20>;
+			reg-io-width = <0x4>;
+			reg-shift = <0x2>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <68>;
+			clocks = <&uart_clk>;
+			status = "disabled";
+		};
+
+		bsca: i2c@406300 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_irq0_intc>;
+		      reg = <0x406300 0x58>;
+		      interrupts = <26>;
+		      interrupt-names = "upg_bsca";
+		      status = "disabled";
+		};
+
+		bscb: i2c@409400 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_aon_irq0_intc>;
+		      reg = <0x409400 0x58>;
+		      interrupts = <28>;
+		      interrupt-names = "upg_bscb";
+		      status = "disabled";
+		};
+
+		bscc: i2c@406200 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_irq0_intc>;
+		      reg = <0x406200 0x58>;
+		      interrupts = <24>;
+		      interrupt-names = "upg_bscc";
+		      status = "disabled";
+		};
+
+		bscd: i2c@406280 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_irq0_intc>;
+		      reg = <0x406280 0x58>;
+		      interrupts = <25>;
+		      interrupt-names = "upg_bscd";
+		      status = "disabled";
+		};
+
+		bsce: i2c@409180 {
+		      clock-frequency = <390000>;
+		      compatible = "brcm,brcmstb-i2c";
+		      interrupt-parent = <&upg_aon_irq0_intc>;
+		      reg = <0x409180 0x58>;
+		      interrupts = <27>;
+		      interrupt-names = "upg_bsce";
+		      status = "disabled";
+		};
+
+		pwma: pwm@406580 {
+			compatible = "brcm,bcm7038-pwm";
+			reg = <0x406580 0x28>;
+			#pwm-cells = <2>;
+			clocks = <&upg_clk>;
+			status = "disabled";
+		};
+
+		pwmb: pwm@406800 {
+			compatible = "brcm,bcm7038-pwm";
+			reg = <0x406800 0x28>;
+			#pwm-cells = <2>;
+			clocks = <&upg_clk>;
+			status = "disabled";
+		};
+
+		watchdog: watchdog@4067e8 {
+			clocks = <&upg_clk>;
+			compatible = "brcm,bcm7038-wdt";
+			reg = <0x4067e8 0x14>;
+			status = "disabled";
+		};
+
+		aon_pm_l2_intc: interrupt-controller@408440 {
+			compatible = "brcm,l2-intc";
+			reg = <0x408440 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <54>;
+			brcm,irq-can-wake;
+		};
+
+		aon_ctrl: syscon@408000 {
+			compatible = "brcm,brcmstb-aon-ctrl";
+			reg = <0x408000 0x100>, <0x408200 0x200>;
+			reg-names = "aon-ctrl", "aon-sram";
+		};
+
+		timers: timer@4067c0 {
+			compatible = "brcm,brcmstb-timers";
+			reg = <0x4067c0 0x40>;
+		};
+
+		upg_gio: gpio@406700 {
+			compatible = "brcm,brcmstb-gpio";
+			reg = <0x406700 0x80>;
+			#gpio-cells = <2>;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			interrupt-controller;
+			interrupt-parent = <&upg_irq0_intc>;
+			interrupts = <6>;
+			brcm,gpio-bank-widths = <32 32 32 21>;
+		};
+
+		upg_gio_aon: gpio@4094c0 {
+			compatible = "brcm,brcmstb-gpio";
+			reg = <0x4094c0 0x40>;
+			#gpio-cells = <2>;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			interrupt-controller;
+			interrupt-parent = <&upg_aon_irq0_intc>;
+			interrupts = <6>;
+			interrupts-extended = <&upg_aon_irq0_intc 6>,
+					      <&aon_pm_l2_intc 5>;
+			wakeup-source;
+			brcm,gpio-bank-widths = <18 4>;
+		};
+
+		enet0: ethernet@b80000 {
+			phy-mode = "internal";
+			phy-handle = <&phy1>;
+			mac-address = [ 00 10 18 36 23 1a ];
+			compatible = "brcm,genet-v3";
+			#address-cells = <0x1>;
+			#size-cells = <0x1>;
+			reg = <0xb80000 0x11c88>;
+			interrupts = <17>, <18>;
+			interrupt-parent = <&periph_intc>;
+			status = "disabled";
+
+			mdio@e14 {
+				compatible = "brcm,genet-mdio-v3";
+				#address-cells = <0x1>;
+				#size-cells = <0x0>;
+				reg = <0xe14 0x8>;
+
+				phy1: ethernet-phy@1 {
+					max-speed = <100>;
+					reg = <0x1>;
+					compatible = "brcm,40nm-ephy",
+						"ethernet-phy-ieee802.3-c22";
+				};
+			};
+		};
+
+		ehci0: usb@480300 {
+			compatible = "brcm,bcm7435-ehci", "generic-ehci";
+			reg = <0x480300 0x100>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <70>;
+			status = "disabled";
+		};
+
+		ohci0: usb@480400 {
+			compatible = "brcm,bcm7435-ohci", "generic-ohci";
+			reg = <0x480400 0x100>;
+			native-endian;
+			no-big-frame-no;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <72>;
+			status = "disabled";
+		};
+
+		ehci1: usb@480500 {
+			compatible = "brcm,bcm7435-ehci", "generic-ehci";
+			reg = <0x480500 0x100>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <71>;
+			status = "disabled";
+		};
+
+		ohci1: usb@480600 {
+			compatible = "brcm,bcm7435-ohci", "generic-ohci";
+			reg = <0x480600 0x100>;
+			native-endian;
+			no-big-frame-no;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <73>;
+			status = "disabled";
+		};
+
+		ehci2: usb@490300 {
+			compatible = "brcm,bcm7435-ehci", "generic-ehci";
+			reg = <0x490300 0x100>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <75>;
+			status = "disabled";
+		};
+
+		ohci2: usb@490400 {
+			compatible = "brcm,bcm7435-ohci", "generic-ohci";
+			reg = <0x490400 0x100>;
+			native-endian;
+			no-big-frame-no;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <77>;
+			status = "disabled";
+		};
+
+		ehci3: usb@490500 {
+			compatible = "brcm,bcm7435-ehci", "generic-ehci";
+			reg = <0x490500 0x100>;
+			native-endian;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <76>;
+			status = "disabled";
+		};
+
+		ohci3: usb@490600 {
+			compatible = "brcm,bcm7435-ohci", "generic-ohci";
+			reg = <0x490600 0x100>;
+			native-endian;
+			no-big-frame-no;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <78>;
+			status = "disabled";
+		};
+
+		hif_l2_intc: interrupt-controller@41b000 {
+			compatible = "brcm,l2-intc";
+			reg = <0x41b000 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <24>;
+		};
+
+		nand: nand@41c800 {
+			compatible = "brcm,brcmnand-v6.2", "brcm,brcmnand";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg-names = "nand", "flash-dma";
+			reg = <0x41c800 0x600>, <0x41d000 0x100>;
+			interrupt-parent = <&hif_l2_intc>;
+			interrupts = <24>, <4>;
+			status = "disabled";
+		};
+
+		sata: sata@181000 {
+			compatible = "brcm,bcm7425-ahci", "brcm,sata3-ahci";
+			reg-names = "ahci", "top-ctrl";
+			reg = <0x181000 0xa9c>, <0x180020 0x1c>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <45>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sata0: sata-port@0 {
+				reg = <0>;
+				phys = <&sata_phy0>;
+			};
+
+			sata1: sata-port@1 {
+				reg = <1>;
+				phys = <&sata_phy1>;
+			};
+		};
+
+		sata_phy: sata-phy@180100 {
+			compatible = "brcm,bcm7425-sata-phy", "brcm,phy-sata3";
+			reg = <0x180100 0x0eff>;
+			reg-names = "phy";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sata_phy0: sata-phy@0 {
+				reg = <0>;
+				#phy-cells = <0>;
+			};
+
+			sata_phy1: sata-phy@1 {
+				reg = <1>;
+				#phy-cells = <0>;
+			};
+		};
+
+		sdhci0: sdhci@41a000 {
+			compatible = "brcm,bcm7425-sdhci";
+			reg = <0x41a000 0x100>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <47>;
+			sd-uhs-sdr50;
+			mmc-hs200-1_8v;
+			status = "disabled";
+		};
+
+		sdhci1: sdhci@41a200 {
+			compatible = "brcm,bcm7425-sdhci";
+			reg = <0x41a200 0x100>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <48>;
+			sd-uhs-sdr50;
+			mmc-hs200-1_8v;
+			status = "disabled";
+		};
+
+		spi_l2_intc: interrupt-controller@41bd00 {
+			compatible = "brcm,l2-intc";
+			reg = <0x41bd00 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&periph_intc>;
+			interrupts = <25>;
+		};
+
+		qspi: spi@41d200 {
+			#address-cells = <0x1>;
+			#size-cells = <0x0>;
+			compatible = "brcm,spi-bcm-qspi",
+				     "brcm,spi-brcmstb-qspi";
+			clocks = <&upg_clk>;
+			reg = <0x41a920 0x4 0x41d400 0x188 0x41d200 0x50>;
+			reg-names = "cs_reg", "hif_mspi", "bspi";
+			interrupts = <0x0 0x1 0x2 0x3 0x4 0x5 0x6>;
+			interrupt-parent = <&spi_l2_intc>;
+			interrupt-names = "spi_lr_fullness_reached",
+					  "spi_lr_session_aborted",
+					  "spi_lr_impatient",
+					  "spi_lr_session_done",
+					  "spi_lr_overread",
+					  "mspi_done",
+					  "mspi_halted";
+			status = "disabled";
+		};
+
+		mspi: spi@409200 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,spi-bcm-qspi",
+				     "brcm,spi-brcmstb-mspi";
+			clocks = <&upg_clk>;
+			reg = <0x409200 0x180>;
+			reg-names = "mspi";
+			interrupts = <0x14>;
+			interrupt-parent = <&upg_aon_irq0_intc>;
+			interrupt-names = "mspi_done";
+			status = "disabled";
+		};
+
+		waketimer: waketimer@409580 {
+			compatible = "brcm,brcmstb-waketimer";
+			reg = <0x409580 0x14>;
+			interrupts = <0x3>;
+			interrupt-parent = <&aon_pm_l2_intc>;
+			interrupt-names = "timer";
+			clocks = <&upg_clk>;
+			status = "disabled";
+		};
+	};
+
+	memory_controllers {
+		compatible = "simple-bus";
+		ranges = <0x0 0x103b0000 0x1a000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		memory-controller@0 {
+			compatible = "brcm,brcmstb-memc", "simple-bus";
+			ranges = <0x0 0x0 0xa000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			memc-arb@1000 {
+				compatible = "brcm,brcmstb-memc-arb";
+				reg = <0x1000 0x248>;
+			};
+
+			memc-ddr@2000 {
+				compatible = "brcm,brcmstb-memc-ddr";
+				reg = <0x2000 0x300>;
+			};
+
+			ddr-phy@6000 {
+				compatible = "brcm,brcmstb-ddr-phy";
+				reg = <0x6000 0xc8>;
+			};
+
+			shimphy@8000 {
+				compatible = "brcm,brcmstb-ddr-shimphy";
+				reg = <0x8000 0x13c>;
+			};
+		};
+
+		memory-controller@1 {
+			compatible = "brcm,brcmstb-memc", "simple-bus";
+			ranges = <0x0 0x10000 0xa000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			memc-arb@1000 {
+				compatible = "brcm,brcmstb-memc-arb";
+				reg = <0x1000 0x248>;
+			};
+
+			memc-ddr@2000 {
+				compatible = "brcm,brcmstb-memc-ddr";
+				reg = <0x2000 0x300>;
+			};
+
+			ddr-phy@6000 {
+				compatible = "brcm,brcmstb-ddr-phy";
+				reg = <0x6000 0xc8>;
+			};
+
+			shimphy@8000 {
+				compatible = "brcm,brcmstb-ddr-shimphy";
+				reg = <0x8000 0x13c>;
+			};
+		};
+	};
+
+	pcie_0: pcie@8b20000 {
+		status = "disabled";
+		compatible = "brcm,bcm7435-pcie";
+
+		ranges = <0x02000000 0x0 0xd0000000 0xd0000000 0x0 0x08000000
+			  0x02000000 0x0 0xd8000000 0xd8000000 0x0 0x08000000
+			  0x02000000 0x0 0xe0000000 0xe0000000 0x0 0x08000000
+			  0x02000000 0x0 0xe8000000 0xe8000000 0x0 0x08000000>;
+
+		reg = <0x10410000 0x19310>;
+		aspm-no-l0s;
+		device_type = "pci";
+		msi-controller;
+		msi-parent = <&pcie_0>;
+		#address-cells = <0x3>;
+		#size-cells = <0x2>;
+		bus-range = <0x0 0xff>;
+		interrupt-map-mask = <0x0 0x0 0x0 0x7>;
+		linux,pci-domain = <0x0>;
+
+		interrupt-parent = <&periph_intc>;
+		interrupts = <39>, <39>;
+		interrupt-names = "pcie", "msi";
+		#interrupt-cells = <0x1>;
+		interrupt-map = <0 0 0 1 &periph_intc 0x23
+				 0 0 0 1 &periph_intc 0x24
+				 0 0 0 1 &periph_intc 0x25
+				 0 0 0 1 &periph_intc 0x26>;
+	};
+};
diff --git a/arch/mips/boot/dts/brcm/bcm93384wvg.dts b/arch/mips/boot/dts/brcm/bcm93384wvg.dts
new file mode 100644
index 000000000..7d3f181b8
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm93384wvg.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "bcm3384_zephyr.dtsi"
+
+/ {
+	compatible = "brcm,bcm93384wvg", "brcm,bcm3384";
+	model = "Broadcom BCM93384WVG";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &uart0;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
diff --git a/arch/mips/boot/dts/brcm/bcm93384wvg_viper.dts b/arch/mips/boot/dts/brcm/bcm93384wvg_viper.dts
new file mode 100644
index 000000000..f845faa0d
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm93384wvg_viper.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "bcm3384_viper.dtsi"
+
+/ {
+	compatible = "brcm,bcm93384wvg-viper", "brcm,bcm3384-viper";
+	model = "Broadcom BCM93384WVG-viper";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &uart0;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
diff --git a/arch/mips/boot/dts/brcm/bcm96368mvwg.dts b/arch/mips/boot/dts/brcm/bcm96368mvwg.dts
new file mode 100644
index 000000000..f5e955085
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm96368mvwg.dts
@@ -0,0 +1,32 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "bcm6368.dtsi"
+
+/ {
+	compatible = "brcm,bcm96368mvwg", "brcm,bcm6368";
+	model = "Broadcom BCM96368MVWG";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x04000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &uart0;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+/* FIXME: need to set up USB_CTRL registers first */
+&ehci {
+	status = "disabled";
+};
+
+&ohci {
+	status = "disabled";
+};
diff --git a/arch/mips/boot/dts/brcm/bcm97125cbmb.dts b/arch/mips/boot/dts/brcm/bcm97125cbmb.dts
new file mode 100644
index 000000000..bda5f7962
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm97125cbmb.dts
@@ -0,0 +1,68 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "bcm7125.dtsi"
+
+/ {
+	compatible = "brcm,bcm97125cbmb", "brcm,bcm7125";
+	model = "Broadcom BCM97125CBMB";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &uart0;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&bsca {
+	status = "okay";
+};
+
+&bscb {
+	status = "okay";
+};
+
+&bscc {
+	status = "okay";
+};
+
+&bscd {
+	status = "okay";
+};
+
+&pwma {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
+/* FIXME: USB is wonky; disable it for now */
+&ehci0 {
+	status = "disabled";
+};
+
+&ohci0 {
+	status = "disabled";
+};
+
+&mspi {
+	status = "okay";
+};
diff --git a/arch/mips/boot/dts/brcm/bcm97346dbsmb.dts b/arch/mips/boot/dts/brcm/bcm97346dbsmb.dts
new file mode 100644
index 000000000..9f73735e8
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm97346dbsmb.dts
@@ -0,0 +1,124 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "bcm7346.dtsi"
+#include "bcm97xxx-nand-cs1-bch24.dtsi"
+
+/ {
+	compatible = "brcm,bcm97346dbsmb", "brcm,bcm7346";
+	model = "Broadcom BCM97346DBSMB";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>, <0x20000000 0x30000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &uart0;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&bsca {
+	status = "okay";
+};
+
+&bscb {
+	status = "okay";
+};
+
+&bscc {
+	status = "okay";
+};
+
+&bscd {
+	status = "okay";
+};
+
+&bsce {
+	status = "okay";
+};
+
+&pwma {
+	status = "okay";
+};
+
+&pwmb {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&enet0 {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&ehci2 {
+	status = "okay";
+};
+
+&ohci2 {
+	status = "okay";
+};
+
+&ehci3 {
+	status = "okay";
+};
+
+&ohci3 {
+	status = "okay";
+};
+
+&nand {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&sata_phy {
+	status = "okay";
+};
+
+&sdhci0 {
+	status = "okay";
+};
+
+&mspi {
+	status = "okay";
+};
+
+&waketimer {
+	status = "okay";
+};
diff --git a/arch/mips/boot/dts/brcm/bcm97358svmb.dts b/arch/mips/boot/dts/brcm/bcm97358svmb.dts
new file mode 100644
index 000000000..c17fc14d4
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm97358svmb.dts
@@ -0,0 +1,116 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "bcm7358.dtsi"
+#include "bcm97xxx-nand-cs1-bch4.dtsi"
+
+/ {
+	compatible = "brcm,bcm97358svmb", "brcm,bcm7358";
+	model = "Broadcom BCM97358SVMB";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &uart0;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&bsca {
+	status = "okay";
+};
+
+&bscb {
+	status = "okay";
+};
+
+&bscc {
+	status = "okay";
+};
+
+&bscd {
+	status = "okay";
+};
+
+&pwma {
+	status = "okay";
+};
+
+&pwmb {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&enet0 {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&nand {
+	status = "okay";
+};
+
+&qspi {
+	status = "okay";
+
+	flash@0 {
+		compatible = "m25p80";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+		spi-cpol;
+		spi-cpha;
+		use-bspi;
+		m25p,fast-read;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			flash0.cfe@0 {
+				reg = <0x0 0x200000>;
+			};
+
+			flash0.mac@200000 {
+				reg = <0x200000 0x40000>;
+			};
+
+			flash0.nvram@240000 {
+				reg = <0x240000 0x10000>;
+			};
+		};
+	};
+};
+
+&mspi {
+	status = "okay";
+};
+
+&waketimer {
+	status = "okay";
+};
diff --git a/arch/mips/boot/dts/brcm/bcm97360svmb.dts b/arch/mips/boot/dts/brcm/bcm97360svmb.dts
new file mode 100644
index 000000000..c9b76f41e
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm97360svmb.dts
@@ -0,0 +1,119 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "bcm7360.dtsi"
+
+/ {
+	compatible = "brcm,bcm97360svmb", "brcm,bcm7360";
+	model = "Broadcom BCM97360SVMB";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &uart0;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&bsca {
+	status = "okay";
+};
+
+&bscb {
+	status = "okay";
+};
+
+&bscc {
+	status = "okay";
+};
+
+&bscd {
+	status = "okay";
+};
+
+&pwma {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&enet0 {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&sata_phy {
+	status = "okay";
+};
+
+&sdhci0 {
+	status = "okay";
+};
+
+&qspi {
+	status = "okay";
+
+	flash@0 {
+		compatible = "m25p80";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+		spi-cpol;
+		spi-cpha;
+		use-bspi;
+		m25p,fast-read;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			flash0.cfe@0 {
+				reg = <0x0 0x200000>;
+			};
+
+			flash0.mac@200000 {
+				reg = <0x200000 0x40000>;
+			};
+
+			flash0.nvram@240000 {
+				reg = <0x240000 0x10000>;
+			};
+		};
+	};
+};
+
+&mspi {
+	status = "okay";
+};
+
+&waketimer {
+	status = "okay";
+};
diff --git a/arch/mips/boot/dts/brcm/bcm97362svmb.dts b/arch/mips/boot/dts/brcm/bcm97362svmb.dts
new file mode 100644
index 000000000..97aeb51b6
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm97362svmb.dts
@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "bcm7362.dtsi"
+#include "bcm97xxx-nand-cs1-bch4.dtsi"
+
+/ {
+	compatible = "brcm,bcm97362svmb", "brcm,bcm7362";
+	model = "Broadcom BCM97362SVMB";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>, <0x20000000 0x30000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &uart0;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&bsca {
+	status = "okay";
+};
+
+&bscb {
+	status = "okay";
+};
+
+&bscd {
+	status = "okay";
+};
+
+&pwma {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&enet0 {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&nand {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&sata_phy {
+	status = "okay";
+};
+
+&sdhci0 {
+	status = "okay";
+};
+
+&mspi {
+	status = "okay";
+};
+
+&waketimer {
+	status = "okay";
+};
diff --git a/arch/mips/boot/dts/brcm/bcm97420c.dts b/arch/mips/boot/dts/brcm/bcm97420c.dts
new file mode 100644
index 000000000..cc70c2dd4
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm97420c.dts
@@ -0,0 +1,90 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "bcm7420.dtsi"
+
+/ {
+	compatible = "brcm,bcm97420c", "brcm,bcm7420";
+	model = "Broadcom BCM97420C";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>,
+		      <0x20000000 0x30000000>,
+		      <0x60000000 0x10000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &uart0;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&bsca {
+	status = "okay";
+};
+
+&bscb {
+	status = "okay";
+};
+
+&bscc {
+	status = "okay";
+};
+
+&bscd {
+	status = "okay";
+};
+
+&bsce {
+	status = "okay";
+};
+
+&pwma {
+	status = "okay";
+};
+
+&pwmb {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
+/* FIXME: MAC driver comes up but cannot attach to PHY */
+&enet0 {
+	status = "disabled";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&mspi {
+	status = "okay";
+};
diff --git a/arch/mips/boot/dts/brcm/bcm97425svmb.dts b/arch/mips/boot/dts/brcm/bcm97425svmb.dts
new file mode 100644
index 000000000..289a57b91
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm97425svmb.dts
@@ -0,0 +1,163 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "bcm7425.dtsi"
+#include "bcm97xxx-nand-cs1-bch24.dtsi"
+
+/ {
+	compatible = "brcm,bcm97425svmb", "brcm,bcm7425";
+	model = "Broadcom BCM97425SVMB";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>,
+		      <0x20000000 0x30000000>,
+		      <0x90000000 0x40000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &uart0;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&bsca {
+	status = "okay";
+};
+
+&bscb {
+	status = "okay";
+};
+
+&bscc {
+	status = "okay";
+};
+
+&bscd {
+	status = "okay";
+};
+
+&bsce {
+	status = "okay";
+};
+
+&pwma {
+	status = "okay";
+};
+
+&pwmb {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&enet0 {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&ehci2 {
+	status = "okay";
+};
+
+&ohci2 {
+	status = "okay";
+};
+
+&ehci3 {
+	status = "okay";
+};
+
+&ohci3 {
+	status = "okay";
+};
+
+&nand {
+	status = "okay";
+};
+
+&sdhci0 {
+	status = "okay";
+};
+
+&sdhci1 {
+	status = "okay";
+};
+
+&qspi {
+	status = "okay";
+
+	flash@0 {
+		compatible = "m25p80";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+		spi-cpol;
+		spi-cpha;
+		use-bspi;
+		m25p,fast-read;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			flash0.cfe@0 {
+				reg = <0x0 0x200000>;
+			};
+
+			flash0.mac@200000 {
+				reg = <0x200000 0x40000>;
+			};
+
+			flash0.nvram@240000 {
+				reg = <0x240000 0x10000>;
+			};
+		};
+	};
+};
+
+&mspi {
+	status = "okay";
+};
+
+&waketimer {
+	status = "okay";
+};
+
+&pcie_0 {
+	status = "okay";
+	/* 1GB Memc0, 1GB Memc1 */
+	brcm,scb-sizes = <0 0x40000000 0 0x40000000>;
+	dma-ranges = <0x43000000 0x00000000 0x00000000 0x00000000 0x0 0x10000000
+		      0x43000000 0x00000000 0x10000000 0x20000000 0x0 0x30000000
+		      0x43000000 0x00000000 0x40000000 0x90000000 0x0 0x40000000>;
+};
diff --git a/arch/mips/boot/dts/brcm/bcm97435svmb.dts b/arch/mips/boot/dts/brcm/bcm97435svmb.dts
new file mode 100644
index 000000000..a0cf53e23
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm97435svmb.dts
@@ -0,0 +1,139 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "bcm7435.dtsi"
+#include "bcm97xxx-nand-cs1-bch24.dtsi"
+
+/ {
+	compatible = "brcm,bcm97435svmb", "brcm,bcm7435";
+	model = "Broadcom BCM97435SVMB";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>,
+		      <0x20000000 0x30000000>,
+		      <0x90000000 0x40000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &uart0;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&bsca {
+	status = "okay";
+};
+
+&bscb {
+	status = "okay";
+};
+
+&bscc {
+	status = "okay";
+};
+
+&bscd {
+	status = "okay";
+};
+
+&bsce {
+	status = "okay";
+};
+
+&pwma {
+	status = "okay";
+};
+
+&pwmb {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&enet0 {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&ehci2 {
+	status = "okay";
+};
+
+&ohci2 {
+	status = "okay";
+};
+
+&ehci3 {
+	status = "okay";
+};
+
+&ohci3 {
+	status = "okay";
+};
+
+&nand {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&sata_phy {
+	status = "okay";
+};
+
+&sdhci0 {
+	status = "okay";
+};
+
+&sdhci1 {
+	status = "okay";
+};
+
+&mspi {
+	status = "okay";
+};
+
+&waketimer {
+	status = "okay";
+};
+
+&pcie_0 {
+	status = "okay";
+	/* 1GB Memc0, 1GB Memc1 */
+	brcm,scb-sizes = <0 0x40000000 0 0x40000000>;
+	dma-ranges = <0x43000000 0x00000000 0x00000000 0x00000000 0x0 0x10000000
+		      0x43000000 0x00000000 0x10000000 0x20000000 0x0 0x30000000
+		      0x43000000 0x00000000 0x40000000 0x90000000 0x0 0x40000000>;
+};
diff --git a/arch/mips/boot/dts/brcm/bcm97xxx-nand-cs1-bch24.dtsi b/arch/mips/boot/dts/brcm/bcm97xxx-nand-cs1-bch24.dtsi
new file mode 100644
index 000000000..96c30d857
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm97xxx-nand-cs1-bch24.dtsi
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0
+&nand {
+	nandcs@1 {
+		compatible = "brcm,nandcs";
+		reg = <1>;
+		nand-on-flash-bbt;
+
+		nand-ecc-strength = <24>;
+		nand-ecc-step-size = <1024>;
+		brcm,nand-oob-sector-size = <27>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			flash1.rootfs@0 {
+				reg = <0x0 0x10000000>;
+			};
+
+			flash1.kernel@10000000 {
+				reg = <0x10000000 0x400000>;
+			};
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/brcm/bcm97xxx-nand-cs1-bch4.dtsi b/arch/mips/boot/dts/brcm/bcm97xxx-nand-cs1-bch4.dtsi
new file mode 100644
index 000000000..7b5afefbb
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm97xxx-nand-cs1-bch4.dtsi
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0
+&nand {
+	nandcs@1 {
+		compatible = "brcm,nandcs";
+		reg = <1>;
+		nand-on-flash-bbt;
+
+		nand-ecc-strength = <4>;
+		nand-ecc-step-size = <512>;
+		brcm,nand-oob-sector-size = <16>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			flash1.rootfs@0 {
+				reg = <0x0 0x10000000>;
+			};
+
+			flash1.kernel@10000000 {
+				reg = <0x10000000 0x400000>;
+			};
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/brcm/bcm9ejtagprb.dts b/arch/mips/boot/dts/brcm/bcm9ejtagprb.dts
new file mode 100644
index 000000000..615d2b977
--- /dev/null
+++ b/arch/mips/boot/dts/brcm/bcm9ejtagprb.dts
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "bcm6328.dtsi"
+
+/ {
+	compatible = "brcm,bcm9ejtagprb", "brcm,bcm6328";
+	model = "Broadcom BCM9EJTAGPRB";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &uart0;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/mips/boot/dts/cavium-octeon/Makefile b/arch/mips/boot/dts/cavium-octeon/Makefile
new file mode 100644
index 000000000..17aef35f3
--- /dev/null
+++ b/arch/mips/boot/dts/cavium-octeon/Makefile
@@ -0,0 +1,4 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_CAVIUM_OCTEON_SOC)	+= octeon_3xxx.dtb octeon_68xx.dtb
+
+obj-$(CONFIG_BUILTIN_DTB)	+= $(addsuffix .o, $(dtb-y))
diff --git a/arch/mips/boot/dts/cavium-octeon/dlink_dsr-1000n.dts b/arch/mips/boot/dts/cavium-octeon/dlink_dsr-1000n.dts
new file mode 100644
index 000000000..2fdb4baad
--- /dev/null
+++ b/arch/mips/boot/dts/cavium-octeon/dlink_dsr-1000n.dts
@@ -0,0 +1,48 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Device tree source for D-Link DSR-1000N.
+ *
+ * Written by: Aaro Koskinen <aaro.koskinen@iki.fi>
+ */
+
+/include/ "dlink_dsr-500n-1000n.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "dlink,dsr-1000n";
+
+	soc@0 {
+		uart0: serial@1180000000800 {
+			clock-frequency = <500000000>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		usb1 {
+			label = "usb1";
+			gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
+		};
+
+		usb2 {
+			label = "usb2";
+			gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
+		};
+
+		wps {
+			label = "wps";
+			gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+		};
+
+		wireless1 {
+			label = "5g";
+			gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+		};
+
+		wireless2 {
+			label = "2.4g";
+			gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/cavium-octeon/dlink_dsr-500n-1000n.dtsi b/arch/mips/boot/dts/cavium-octeon/dlink_dsr-500n-1000n.dtsi
new file mode 100644
index 000000000..b4acdb26a
--- /dev/null
+++ b/arch/mips/boot/dts/cavium-octeon/dlink_dsr-500n-1000n.dtsi
@@ -0,0 +1,55 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Device tree source for D-Link DSR-500N/1000N (common parts).
+ *
+ * Written by: Aaro Koskinen <aaro.koskinen@iki.fi>
+ */
+
+/include/ "octeon_3xxx.dtsi"
+
+/ {
+	soc@0 {
+		smi0: mdio@1180000001800 {
+			phy8: ethernet-phy@8 {
+				reg = <8>;
+				compatible = "ethernet-phy-ieee802.3-c22";
+			};
+		};
+
+		pip: pip@11800a0000000 {
+			interface@0 {
+				ethernet@0 {
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
+				};
+				ethernet@1 {
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
+				};
+				ethernet@2 {
+					phy-handle = <&phy8>;
+				};
+			};
+		};
+
+		twsi0: i2c@1180000001000 {
+			rtc@68 {
+				compatible = "dallas,ds1337";
+				reg = <0x68>;
+			};
+		};
+
+		usbn: usbn@1180068000000 {
+			refclk-frequency = <12000000>;
+			refclk-type = "crystal";
+		};
+	};
+
+	aliases {
+		pip = &pip;
+	};
+};
diff --git a/arch/mips/boot/dts/cavium-octeon/dlink_dsr-500n.dts b/arch/mips/boot/dts/cavium-octeon/dlink_dsr-500n.dts
new file mode 100644
index 000000000..e04237281
--- /dev/null
+++ b/arch/mips/boot/dts/cavium-octeon/dlink_dsr-500n.dts
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Device tree source for D-Link DSR-500N.
+ *
+ * Written by: Aaro Koskinen <aaro.koskinen@iki.fi>
+ */
+
+/include/ "dlink_dsr-500n-1000n.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "dlink,dsr-500n";
+	compatible = "dlink,dsr-500n", "cavium,octeon-3860";
+
+	soc@0 {
+		uart0: serial@1180000000800 {
+			clock-frequency = <300000000>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		usb {
+			gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
+		};
+
+		wps {
+			gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+		};
+
+		wireless {
+			label = "2.4g";
+			gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/cavium-octeon/octeon_3xxx.dts b/arch/mips/boot/dts/cavium-octeon/octeon_3xxx.dts
new file mode 100644
index 000000000..dda0559ce
--- /dev/null
+++ b/arch/mips/boot/dts/cavium-octeon/octeon_3xxx.dts
@@ -0,0 +1,406 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * OCTEON 3XXX, 5XXX, 63XX device tree skeleton.
+ *
+ * This device tree is pruned and patched by early boot code before
+ * use.	 Because of this, it contains a super-set of the available
+ * devices and properties.
+ */
+
+/include/ "octeon_3xxx.dtsi"
+
+/ {
+	soc@0 {
+		smi0: mdio@1180000001800 {
+			phy0: ethernet-phy@0 {
+				compatible = "marvell,88e1118";
+				marvell,reg-init =
+					/* Fix rx and tx clock transition timing */
+					<2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */
+					/* Adjust LED drive. */
+					<3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */
+					/* irq, blink-activity, blink-link */
+					<3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */
+				reg = <0>;
+			};
+
+			phy1: ethernet-phy@1 {
+				compatible = "marvell,88e1118";
+				marvell,reg-init =
+					/* Fix rx and tx clock transition timing */
+					<2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */
+					/* Adjust LED drive. */
+					<3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */
+					/* irq, blink-activity, blink-link */
+					<3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */
+				reg = <1>;
+			};
+
+			phy2: ethernet-phy@2 {
+				reg = <2>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy3: ethernet-phy@3 {
+				reg = <3>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy4: ethernet-phy@4 {
+				reg = <4>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy5: ethernet-phy@5 {
+				reg = <5>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+
+			phy6: ethernet-phy@6 {
+				reg = <6>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy7: ethernet-phy@7 {
+				reg = <7>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy8: ethernet-phy@8 {
+				reg = <8>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy9: ethernet-phy@9 {
+				reg = <9>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+		};
+
+		smi1: mdio@1180000001900 {
+			compatible = "cavium,octeon-3860-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x11800 0x00001900 0x0 0x40>;
+
+			phy100: ethernet-phy@1 {
+				reg = <1>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+				interrupt-parent = <&gpio>;
+				interrupts = <12 8>; /* Pin 12, active low */
+			};
+			phy101: ethernet-phy@2 {
+				reg = <2>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+				interrupt-parent = <&gpio>;
+				interrupts = <12 8>; /* Pin 12, active low */
+			};
+			phy102: ethernet-phy@3 {
+				reg = <3>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+				interrupt-parent = <&gpio>;
+				interrupts = <12 8>; /* Pin 12, active low */
+			};
+			phy103: ethernet-phy@4 {
+				reg = <4>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+				interrupt-parent = <&gpio>;
+				interrupts = <12 8>; /* Pin 12, active low */
+			};
+		};
+
+		mix0: ethernet@1070000100000 {
+			compatible = "cavium,octeon-5750-mix";
+			reg = <0x10700 0x00100000 0x0 0x100>, /* MIX */
+			      <0x11800 0xE0000000 0x0 0x300>, /* AGL */
+			      <0x11800 0xE0000400 0x0 0x400>, /* AGL_SHARED  */
+			      <0x11800 0xE0002000 0x0 0x8>;   /* AGL_PRT_CTL */
+			cell-index = <0>;
+			interrupts = <0 62>, <1 46>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			phy-handle = <&phy0>;
+		};
+
+		mix1: ethernet@1070000100800 {
+			compatible = "cavium,octeon-5750-mix";
+			reg = <0x10700 0x00100800 0x0 0x100>, /* MIX */
+			      <0x11800 0xE0000800 0x0 0x300>, /* AGL */
+			      <0x11800 0xE0000400 0x0 0x400>, /* AGL_SHARED  */
+			      <0x11800 0xE0002008 0x0 0x8>;   /* AGL_PRT_CTL */
+			cell-index = <1>;
+			interrupts = <1 18>, < 1 46>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			phy-handle = <&phy1>;
+		};
+
+		pip: pip@11800a0000000 {
+			interface@0 {
+				ethernet@0 {
+					phy-handle = <&phy2>;
+					cavium,alt-phy-handle = <&phy100>;
+					rx-delay = <0>;
+					tx-delay = <0>;
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
+				};
+				ethernet@1 {
+					phy-handle = <&phy3>;
+					cavium,alt-phy-handle = <&phy101>;
+					rx-delay = <0>;
+					tx-delay = <0>;
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
+				};
+				ethernet@2 {
+					phy-handle = <&phy4>;
+					cavium,alt-phy-handle = <&phy102>;
+					rx-delay = <0>;
+					tx-delay = <0>;
+				};
+				ethernet@3 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x3>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy5>;
+					cavium,alt-phy-handle = <&phy103>;
+				};
+				ethernet@4 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x4>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@5 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x5>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@6 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x6>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@7 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x7>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@8 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x8>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@9 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x9>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@a {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0xa>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@b {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0xb>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@c {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0xc>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@d {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0xd>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@e {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0xe>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@f {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0xf>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+			};
+
+			interface@1 {
+				ethernet@0 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x0>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy6>;
+				};
+				ethernet@1 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x1>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy7>;
+				};
+				ethernet@2 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x2>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy8>;
+				};
+				ethernet@3 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x3>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy9>;
+				};
+			};
+		};
+
+		twsi0: i2c@1180000001000 {
+			rtc@68 {
+				compatible = "dallas,ds1337";
+				reg = <0x68>;
+			};
+			tmp@4c {
+				compatible = "ti,tmp421";
+				reg = <0x4c>;
+			};
+		};
+
+		twsi1: i2c@1180000001200 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "cavium,octeon-3860-twsi";
+			reg = <0x11800 0x00001200 0x0 0x200>;
+			interrupts = <0 59>;
+			clock-frequency = <100000>;
+		};
+
+		uart1: serial@1180000000c00 {
+			compatible = "cavium,octeon-3860-uart","ns16550";
+			reg = <0x11800 0x00000c00 0x0 0x400>;
+			clock-frequency = <0>;
+			current-speed = <115200>;
+			reg-shift = <3>;
+			interrupts = <0 35>;
+		};
+
+		uart2: serial@1180000000400 {
+			compatible = "cavium,octeon-3860-uart","ns16550";
+			reg = <0x11800 0x00000400 0x0 0x400>;
+			clock-frequency = <0>;
+			current-speed = <115200>;
+			reg-shift = <3>;
+			interrupts = <1 16>;
+		};
+
+		bootbus: bootbus@1180000000000 {
+			led0: led-display@4,0 {
+				compatible = "avago,hdsp-253x";
+				reg = <4 0x20 0x20>, <4 0 0x20>;
+			};
+
+			cf0: compact-flash@5,0 {
+				compatible = "cavium,ebt3000-compact-flash";
+				reg = <5 0 0x10000>, <6 0 0x10000>;
+				cavium,bus-width = <16>;
+				cavium,true-ide;
+				cavium,dma-engine-handle = <&dma0>;
+			};
+		};
+
+		uctl: uctl@118006f000000 {
+			compatible = "cavium,octeon-6335-uctl";
+			reg = <0x11800 0x6f000000 0x0 0x100>;
+			ranges; /* Direct mapping */
+			#address-cells = <2>;
+			#size-cells = <2>;
+			/* 12MHz, 24MHz and 48MHz allowed */
+			refclk-frequency = <12000000>;
+			/* Either "crystal" or "external" */
+			refclk-type = "crystal";
+
+			ehci@16f0000000000 {
+				compatible = "cavium,octeon-6335-ehci","usb-ehci";
+				reg = <0x16f00 0x00000000 0x0 0x100>;
+				interrupts = <0 56>;
+				big-endian-regs;
+			};
+			ohci@16f0000000400 {
+				compatible = "cavium,octeon-6335-ohci","usb-ohci";
+				reg = <0x16f00 0x00000400 0x0 0x100>;
+				interrupts = <0 56>;
+				big-endian-regs;
+			};
+		};
+
+		usbn: usbn@1180068000000 {
+			/* 12MHz, 24MHz and 48MHz allowed */
+			refclk-frequency = <12000000>;
+			/* Either "crystal" or "external" */
+			refclk-type = "crystal";
+		};
+	};
+
+	aliases {
+		mix0 = &mix0;
+		mix1 = &mix1;
+		pip = &pip;
+		smi0 = &smi0;
+		smi1 = &smi1;
+		twsi0 = &twsi0;
+		twsi1 = &twsi1;
+		uart0 = &uart0;
+		uart1 = &uart1;
+		uart2 = &uart2;
+		flash0 = &flash0;
+		cf0 = &cf0;
+		uctl = &uctl;
+		usbn = &usbn;
+		led0 = &led0;
+	};
+ };
diff --git a/arch/mips/boot/dts/cavium-octeon/octeon_3xxx.dtsi b/arch/mips/boot/dts/cavium-octeon/octeon_3xxx.dtsi
new file mode 100644
index 000000000..3c296623d
--- /dev/null
+++ b/arch/mips/boot/dts/cavium-octeon/octeon_3xxx.dtsi
@@ -0,0 +1,232 @@
+// SPDX-License-Identifier: GPL-2.0
+/* OCTEON 3XXX DTS common parts. */
+
+/dts-v1/;
+
+/ {
+	compatible = "cavium,octeon-3860";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&ciu>;
+
+	soc@0 {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges; /* Direct mapping */
+
+		ciu: interrupt-controller@1070000000000 {
+			compatible = "cavium,octeon-3860-ciu";
+			interrupt-controller;
+			/* Interrupts are specified by two parts:
+			 * 1) Controller register (0 or 1)
+			 * 2) Bit within the register (0..63)
+			 */
+			#interrupt-cells = <2>;
+			reg = <0x10700 0x00000000 0x0 0x7000>;
+		};
+
+		gpio: gpio-controller@1070000000800 {
+			#gpio-cells = <2>;
+			compatible = "cavium,octeon-3860-gpio";
+			reg = <0x10700 0x00000800 0x0 0x100>;
+			gpio-controller;
+			/* Interrupts are specified by two parts:
+			 * 1) GPIO pin number (0..15)
+			 * 2) Triggering (1 - edge rising
+			 *		  2 - edge falling
+			 *		  4 - level active high
+			 *		  8 - level active low)
+			 */
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			/* The GPIO pin connect to 16 consecutive CUI bits */
+			interrupts = <0 16>, <0 17>, <0 18>, <0 19>,
+				     <0 20>, <0 21>, <0 22>, <0 23>,
+				     <0 24>, <0 25>, <0 26>, <0 27>,
+				     <0 28>, <0 29>, <0 30>, <0 31>;
+		};
+
+		smi0: mdio@1180000001800 {
+			compatible = "cavium,octeon-3860-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x11800 0x00001800 0x0 0x40>;
+		};
+
+		pip: pip@11800a0000000 {
+			compatible = "cavium,octeon-3860-pip";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x11800 0xa0000000 0x0 0x2000>;
+
+			interface@0 {
+				compatible = "cavium,octeon-3860-pip-interface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>; /* interface */
+
+				ethernet@0 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x0>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@1 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x1>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+				ethernet@2 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x2>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+			};
+
+			interface@1 {
+				compatible = "cavium,octeon-3860-pip-interface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <1>; /* interface */
+			};
+		};
+
+		twsi0: i2c@1180000001000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "cavium,octeon-3860-twsi";
+			reg = <0x11800 0x00001000 0x0 0x200>;
+			interrupts = <0 45>;
+			clock-frequency = <100000>;
+		};
+
+		uart0: serial@1180000000800 {
+			compatible = "cavium,octeon-3860-uart","ns16550";
+			reg = <0x11800 0x00000800 0x0 0x400>;
+			clock-frequency = <0>;
+			current-speed = <115200>;
+			reg-shift = <3>;
+			interrupts = <0 34>;
+		};
+
+		bootbus: bootbus@1180000000000 {
+			compatible = "cavium,octeon-3860-bootbus";
+			reg = <0x11800 0x00000000 0x0 0x200>;
+			/* The chip select number and offset */
+			#address-cells = <2>;
+			/* The size of the chip select region */
+			#size-cells = <1>;
+			ranges = <0 0  0x0 0x1f400000  0xc00000>,
+				 <1 0  0x10000 0x30000000  0>,
+				 <2 0  0x10000 0x40000000  0>,
+				 <3 0  0x10000 0x50000000  0>,
+				 <4 0  0x0 0x1d020000  0x10000>,
+				 <5 0  0x0 0x1d040000  0x10000>,
+				 <6 0  0x0 0x1d050000  0x10000>,
+				 <7 0  0x10000 0x90000000  0>;
+
+			cavium,cs-config@0 {
+				compatible = "cavium,octeon-3860-bootbus-config";
+				cavium,cs-index = <0>;
+				cavium,t-adr  = <20>;
+				cavium,t-ce   = <60>;
+				cavium,t-oe   = <60>;
+				cavium,t-we   = <45>;
+				cavium,t-rd-hld = <35>;
+				cavium,t-wr-hld = <45>;
+				cavium,t-pause	= <0>;
+				cavium,t-wait	= <0>;
+				cavium,t-page	= <35>;
+				cavium,t-rd-dly = <0>;
+
+				cavium,pages	 = <0>;
+				cavium,bus-width = <8>;
+			};
+			cavium,cs-config@4 {
+				compatible = "cavium,octeon-3860-bootbus-config";
+				cavium,cs-index = <4>;
+				cavium,t-adr  = <320>;
+				cavium,t-ce   = <320>;
+				cavium,t-oe   = <320>;
+				cavium,t-we   = <320>;
+				cavium,t-rd-hld = <320>;
+				cavium,t-wr-hld = <320>;
+				cavium,t-pause	= <320>;
+				cavium,t-wait	= <320>;
+				cavium,t-page	= <320>;
+				cavium,t-rd-dly = <0>;
+
+				cavium,pages	 = <0>;
+				cavium,bus-width = <8>;
+			};
+			cavium,cs-config@5 {
+				compatible = "cavium,octeon-3860-bootbus-config";
+				cavium,cs-index = <5>;
+				cavium,t-adr  = <5>;
+				cavium,t-ce   = <300>;
+				cavium,t-oe   = <125>;
+				cavium,t-we   = <150>;
+				cavium,t-rd-hld = <100>;
+				cavium,t-wr-hld = <30>;
+				cavium,t-pause	= <0>;
+				cavium,t-wait	= <30>;
+				cavium,t-page	= <320>;
+				cavium,t-rd-dly = <0>;
+
+				cavium,pages	 = <0>;
+				cavium,bus-width = <16>;
+			};
+			cavium,cs-config@6 {
+				compatible = "cavium,octeon-3860-bootbus-config";
+				cavium,cs-index = <6>;
+				cavium,t-adr  = <5>;
+				cavium,t-ce   = <300>;
+				cavium,t-oe   = <270>;
+				cavium,t-we   = <150>;
+				cavium,t-rd-hld = <100>;
+				cavium,t-wr-hld = <70>;
+				cavium,t-pause	= <0>;
+				cavium,t-wait	= <0>;
+				cavium,t-page	= <320>;
+				cavium,t-rd-dly = <0>;
+
+				cavium,pages	 = <0>;
+				cavium,wait-mode;
+				cavium,bus-width = <16>;
+			};
+
+			flash0: nor@0,0 {
+				compatible = "cfi-flash";
+				reg = <0 0 0x800000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+			};
+		};
+
+		dma0: dma-engine@1180000000100 {
+			compatible = "cavium,octeon-5750-bootbus-dma";
+			reg = <0x11800 0x00000100 0x0 0x8>;
+			interrupts = <0 63>;
+		};
+
+		dma1: dma-engine@1180000000108 {
+			compatible = "cavium,octeon-5750-bootbus-dma";
+			reg = <0x11800 0x00000108 0x0 0x8>;
+			interrupts = <0 63>;
+		};
+
+		usbn: usbn@1180068000000 {
+			compatible = "cavium,octeon-5750-usbn";
+			reg = <0x11800 0x68000000 0x0 0x1000>;
+			ranges; /* Direct mapping */
+			#address-cells = <2>;
+			#size-cells = <2>;
+
+			usbc@16f0010000000 {
+				compatible = "cavium,octeon-5750-usbc";
+				reg = <0x16f00 0x10000000 0x0 0x80000>;
+				interrupts = <0 56>;
+			};
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/cavium-octeon/octeon_68xx.dts b/arch/mips/boot/dts/cavium-octeon/octeon_68xx.dts
new file mode 100644
index 000000000..3d0acbb2e
--- /dev/null
+++ b/arch/mips/boot/dts/cavium-octeon/octeon_68xx.dts
@@ -0,0 +1,626 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+/*
+ * OCTEON 68XX device tree skeleton.
+ *
+ * This device tree is pruned and patched by early boot code before
+ * use.	 Because of this, it contains a super-set of the available
+ * devices and properties.
+ */
+/ {
+	compatible = "cavium,octeon-6880";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&ciu2>;
+
+	soc@0 {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges; /* Direct mapping */
+
+		ciu2: interrupt-controller@1070100000000 {
+			compatible = "cavium,octeon-6880-ciu2";
+			interrupt-controller;
+			/* Interrupts are specified by two parts:
+			 * 1) Controller register (0 or 7)
+			 * 2) Bit within the register (0..63)
+			 */
+			#address-cells = <0>;
+			#interrupt-cells = <2>;
+			reg = <0x10701 0x00000000 0x0 0x4000000>;
+		};
+
+		gpio: gpio-controller@1070000000800 {
+			#gpio-cells = <2>;
+			compatible = "cavium,octeon-3860-gpio";
+			reg = <0x10700 0x00000800 0x0 0x100>;
+			gpio-controller;
+			/* Interrupts are specified by two parts:
+			 * 1) GPIO pin number (0..15)
+			 * 2) Triggering (1 - edge rising
+			 *		  2 - edge falling
+			 *		  4 - level active high
+			 *		  8 - level active low)
+			 */
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			/* The GPIO pins connect to 16 consecutive CUI bits */
+			interrupts = <7 0>,  <7 1>,  <7 2>,  <7 3>,
+				     <7 4>,  <7 5>,  <7 6>,  <7 7>,
+				     <7 8>,  <7 9>,  <7 10>, <7 11>,
+				     <7 12>, <7 13>, <7 14>, <7 15>;
+		};
+
+		smi0: mdio@1180000003800 {
+			compatible = "cavium,octeon-3860-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x11800 0x00003800 0x0 0x40>;
+
+			phy0: ethernet-phy@6 {
+				compatible = "marvell,88e1118";
+				marvell,reg-init =
+					/* Fix rx and tx clock transition timing */
+					<2 0x15 0xffcf 0>, /* Reg 2,21 Clear bits 4, 5 */
+					/* Adjust LED drive. */
+					<3 0x11 0 0x442a>, /* Reg 3,17 <- 0442a */
+					/* irq, blink-activity, blink-link */
+					<3 0x10 0 0x0242>; /* Reg 3,16 <- 0x0242 */
+				reg = <6>;
+			};
+
+			phy1: ethernet-phy@1 {
+				cavium,qlm-trim = "4,sgmii";
+				reg = <1>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy2: ethernet-phy@2 {
+				cavium,qlm-trim = "4,sgmii";
+				reg = <2>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy3: ethernet-phy@3 {
+				cavium,qlm-trim = "4,sgmii";
+				reg = <3>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy4: ethernet-phy@4 {
+				cavium,qlm-trim = "4,sgmii";
+				reg = <4>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+		};
+
+		smi1: mdio@1180000003880 {
+			compatible = "cavium,octeon-3860-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x11800 0x00003880 0x0 0x40>;
+
+			phy41: ethernet-phy@1 {
+				cavium,qlm-trim = "0,sgmii";
+				reg = <1>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy42: ethernet-phy@2 {
+				cavium,qlm-trim = "0,sgmii";
+				reg = <2>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy43: ethernet-phy@3 {
+				cavium,qlm-trim = "0,sgmii";
+				reg = <3>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy44: ethernet-phy@4 {
+				cavium,qlm-trim = "0,sgmii";
+				reg = <4>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+		};
+
+		smi2: mdio@1180000003900 {
+			compatible = "cavium,octeon-3860-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x11800 0x00003900 0x0 0x40>;
+
+			phy21: ethernet-phy@1 {
+				cavium,qlm-trim = "2,sgmii";
+				reg = <1>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy22: ethernet-phy@2 {
+				cavium,qlm-trim = "2,sgmii";
+				reg = <2>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy23: ethernet-phy@3 {
+				cavium,qlm-trim = "2,sgmii";
+				reg = <3>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy24: ethernet-phy@4 {
+				cavium,qlm-trim = "2,sgmii";
+				reg = <4>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+		};
+
+		smi3: mdio@1180000003980 {
+			compatible = "cavium,octeon-3860-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x11800 0x00003980 0x0 0x40>;
+
+			phy11: ethernet-phy@1 {
+				cavium,qlm-trim = "3,sgmii";
+				reg = <1>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy12: ethernet-phy@2 {
+				cavium,qlm-trim = "3,sgmii";
+				reg = <2>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy13: ethernet-phy@3 {
+				cavium,qlm-trim = "3,sgmii";
+				reg = <3>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+			phy14: ethernet-phy@4 {
+				cavium,qlm-trim = "3,sgmii";
+				reg = <4>;
+				compatible = "marvell,88e1149r";
+				marvell,reg-init = <3 0x10 0 0x5777>,
+					<3 0x11 0 0x00aa>,
+					<3 0x12 0 0x4105>,
+					<3 0x13 0 0x0a60>;
+			};
+		};
+
+		mix0: ethernet@1070000100000 {
+			compatible = "cavium,octeon-5750-mix";
+			reg = <0x10700 0x00100000 0x0 0x100>, /* MIX */
+			      <0x11800 0xE0000000 0x0 0x300>, /* AGL */
+			      <0x11800 0xE0000400 0x0 0x400>, /* AGL_SHARED  */
+			      <0x11800 0xE0002000 0x0 0x8>;   /* AGL_PRT_CTL */
+			cell-index = <0>;
+			interrupts = <6 40>, <6 32>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+			phy-handle = <&phy0>;
+		};
+
+		pip: pip@11800a0000000 {
+			compatible = "cavium,octeon-3860-pip";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x11800 0xa0000000 0x0 0x2000>;
+
+			interface@4 {
+				compatible = "cavium,octeon-3860-pip-interface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x4>; /* interface */
+
+				ethernet@0 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x0>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy1>;
+				};
+				ethernet@1 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x1>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy2>;
+				};
+				ethernet@2 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x2>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy3>;
+				};
+				ethernet@3 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x3>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy4>;
+				};
+			};
+
+			interface@3 {
+				compatible = "cavium,octeon-3860-pip-interface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x3>; /* interface */
+
+				ethernet@0 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x0>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy11>;
+				};
+				ethernet@1 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x1>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy12>;
+				};
+				ethernet@2 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x2>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy13>;
+				};
+				ethernet@3 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x3>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy14>;
+				};
+			};
+
+			interface@2 {
+				compatible = "cavium,octeon-3860-pip-interface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x2>; /* interface */
+
+				ethernet@0 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x0>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy21>;
+				};
+				ethernet@1 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x1>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy22>;
+				};
+				ethernet@2 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x2>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy23>;
+				};
+				ethernet@3 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x3>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy24>;
+				};
+			};
+
+			interface@1 {
+				compatible = "cavium,octeon-3860-pip-interface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x1>; /* interface */
+
+				ethernet@0 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x0>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+				};
+			};
+
+			interface@0 {
+				compatible = "cavium,octeon-3860-pip-interface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x0>; /* interface */
+
+				ethernet@0 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x0>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy41>;
+				};
+				ethernet@1 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x1>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy42>;
+				};
+				ethernet@2 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x2>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy43>;
+				};
+				ethernet@3 {
+					compatible = "cavium,octeon-3860-pip-port";
+					reg = <0x3>; /* Port */
+					local-mac-address = [ 00 00 00 00 00 00 ];
+					phy-handle = <&phy44>;
+				};
+			};
+		};
+
+		twsi0: i2c@1180000001000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "cavium,octeon-3860-twsi";
+			reg = <0x11800 0x00001000 0x0 0x200>;
+			interrupts = <3 32>;
+			clock-frequency = <100000>;
+
+			rtc@68 {
+				compatible = "dallas,ds1337";
+				reg = <0x68>;
+			};
+			tmp@4c {
+				compatible = "ti,tmp421";
+				reg = <0x4c>;
+			};
+		};
+
+		twsi1: i2c@1180000001200 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "cavium,octeon-3860-twsi";
+			reg = <0x11800 0x00001200 0x0 0x200>;
+			interrupts = <3 33>;
+			clock-frequency = <100000>;
+		};
+
+		uart0: serial@1180000000800 {
+			compatible = "cavium,octeon-3860-uart","ns16550";
+			reg = <0x11800 0x00000800 0x0 0x400>;
+			clock-frequency = <0>;
+			current-speed = <115200>;
+			reg-shift = <3>;
+			interrupts = <3 36>;
+		};
+
+		uart1: serial@1180000000c00 {
+			compatible = "cavium,octeon-3860-uart","ns16550";
+			reg = <0x11800 0x00000c00 0x0 0x400>;
+			clock-frequency = <0>;
+			current-speed = <115200>;
+			reg-shift = <3>;
+			interrupts = <3 37>;
+		};
+
+		bootbus: bootbus@1180000000000 {
+			compatible = "cavium,octeon-3860-bootbus";
+			reg = <0x11800 0x00000000 0x0 0x200>;
+			/* The chip select number and offset */
+			#address-cells = <2>;
+			/* The size of the chip select region */
+			#size-cells = <1>;
+			ranges = <0 0  0       0x1f400000  0xc00000>,
+				 <1 0  0x10000 0x30000000  0>,
+				 <2 0  0x10000 0x40000000  0>,
+				 <3 0  0x10000 0x50000000  0>,
+				 <4 0  0       0x1d020000  0x10000>,
+				 <5 0  0       0x1d040000  0x10000>,
+				 <6 0  0       0x1d050000  0x10000>,
+				 <7 0  0x10000 0x90000000  0>;
+
+			cavium,cs-config@0 {
+				compatible = "cavium,octeon-3860-bootbus-config";
+				cavium,cs-index = <0>;
+				cavium,t-adr  = <10>;
+				cavium,t-ce   = <50>;
+				cavium,t-oe   = <50>;
+				cavium,t-we   = <35>;
+				cavium,t-rd-hld = <25>;
+				cavium,t-wr-hld = <35>;
+				cavium,t-pause	= <0>;
+				cavium,t-wait	= <300>;
+				cavium,t-page	= <25>;
+				cavium,t-rd-dly = <0>;
+
+				cavium,pages	 = <0>;
+				cavium,bus-width = <8>;
+			};
+			cavium,cs-config@4 {
+				compatible = "cavium,octeon-3860-bootbus-config";
+				cavium,cs-index = <4>;
+				cavium,t-adr  = <320>;
+				cavium,t-ce   = <320>;
+				cavium,t-oe   = <320>;
+				cavium,t-we   = <320>;
+				cavium,t-rd-hld = <320>;
+				cavium,t-wr-hld = <320>;
+				cavium,t-pause	= <320>;
+				cavium,t-wait	= <320>;
+				cavium,t-page	= <320>;
+				cavium,t-rd-dly = <0>;
+
+				cavium,pages	 = <0>;
+				cavium,bus-width = <8>;
+			};
+			cavium,cs-config@5 {
+				compatible = "cavium,octeon-3860-bootbus-config";
+				cavium,cs-index = <5>;
+				cavium,t-adr  = <0>;
+				cavium,t-ce   = <300>;
+				cavium,t-oe   = <125>;
+				cavium,t-we   = <150>;
+				cavium,t-rd-hld = <100>;
+				cavium,t-wr-hld = <300>;
+				cavium,t-pause	= <0>;
+				cavium,t-wait	= <300>;
+				cavium,t-page	= <310>;
+				cavium,t-rd-dly = <0>;
+
+				cavium,pages	 = <0>;
+				cavium,bus-width = <16>;
+			};
+			cavium,cs-config@6 {
+				compatible = "cavium,octeon-3860-bootbus-config";
+				cavium,cs-index = <6>;
+				cavium,t-adr  = <0>;
+				cavium,t-ce   = <30>;
+				cavium,t-oe   = <125>;
+				cavium,t-we   = <150>;
+				cavium,t-rd-hld = <100>;
+				cavium,t-wr-hld = <30>;
+				cavium,t-pause	= <0>;
+				cavium,t-wait	= <30>;
+				cavium,t-page	= <310>;
+				cavium,t-rd-dly = <0>;
+
+				cavium,pages	 = <0>;
+				cavium,wait-mode;
+				cavium,bus-width = <16>;
+			};
+
+			flash0: nor@0,0 {
+				compatible = "cfi-flash";
+				reg = <0 0 0x800000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				partition@0 {
+					label = "bootloader";
+					reg = <0 0x200000>;
+					read-only;
+				};
+				partition@200000 {
+					label = "kernel";
+					reg = <0x200000 0x200000>;
+				};
+				partition@400000 {
+					label = "cramfs";
+					reg = <0x400000 0x3fe000>;
+				};
+				partition@7fe000 {
+					label = "environment";
+					reg = <0x7fe000 0x2000>;
+					read-only;
+				};
+			};
+
+			led0: led-display@4,0 {
+				compatible = "avago,hdsp-253x";
+				reg = <4 0x20 0x20>, <4 0 0x20>;
+			};
+
+			compact-flash@5,0 {
+				compatible = "cavium,ebt3000-compact-flash";
+				reg = <5 0 0x10000>, <6 0 0x10000>;
+				cavium,bus-width = <16>;
+				cavium,true-ide;
+				cavium,dma-engine-handle = <&dma0>;
+			};
+		};
+
+		dma0: dma-engine@1180000000100 {
+			compatible = "cavium,octeon-5750-bootbus-dma";
+			reg = <0x11800 0x00000100 0x0 0x8>;
+			interrupts = <0 63>;
+		};
+		dma1: dma-engine@1180000000108 {
+			compatible = "cavium,octeon-5750-bootbus-dma";
+			reg = <0x11800 0x00000108 0x0 0x8>;
+			interrupts = <0 63>;
+		};
+
+		uctl: uctl@118006f000000 {
+			compatible = "cavium,octeon-6335-uctl";
+			reg = <0x11800 0x6f000000 0x0 0x100>;
+			ranges; /* Direct mapping */
+			#address-cells = <2>;
+			#size-cells = <2>;
+			/* 12MHz, 24MHz and 48MHz allowed */
+			refclk-frequency = <12000000>;
+			/* Either "crystal" or "external" */
+			refclk-type = "crystal";
+
+			ehci@16f0000000000 {
+				compatible = "cavium,octeon-6335-ehci","usb-ehci";
+				reg = <0x16f00 0x00000000 0x0 0x100>;
+				interrupts = <3 44>;
+				big-endian-regs;
+			};
+			ohci@16f0000000400 {
+				compatible = "cavium,octeon-6335-ohci","usb-ohci";
+				reg = <0x16f00 0x00000400 0x0 0x100>;
+				interrupts = <3 44>;
+				big-endian-regs;
+			};
+		};
+	};
+
+	aliases {
+		mix0 = &mix0;
+		pip = &pip;
+		smi0 = &smi0;
+		smi1 = &smi1;
+		smi2 = &smi2;
+		smi3 = &smi3;
+		twsi0 = &twsi0;
+		twsi1 = &twsi1;
+		uart0 = &uart0;
+		uart1 = &uart1;
+		uctl = &uctl;
+		led0 = &led0;
+		flash0 = &flash0;
+	};
+ };
diff --git a/arch/mips/boot/dts/cavium-octeon/ubnt_e100.dts b/arch/mips/boot/dts/cavium-octeon/ubnt_e100.dts
new file mode 100644
index 000000000..cb219b730
--- /dev/null
+++ b/arch/mips/boot/dts/cavium-octeon/ubnt_e100.dts
@@ -0,0 +1,62 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Device tree source for EdgeRouter Lite.
+ *
+ * Written by: Aaro Koskinen <aaro.koskinen@iki.fi>
+ */
+
+/include/ "octeon_3xxx.dtsi"
+
+/ {
+	model = "ubnt,e100";
+
+	soc@0 {
+		smi0: mdio@1180000001800 {
+			phy5: ethernet-phy@5 {
+				reg = <5>;
+				compatible = "ethernet-phy-ieee802.3-c22";
+			};
+			phy6: ethernet-phy@6 {
+				reg = <6>;
+				compatible = "ethernet-phy-ieee802.3-c22";
+			};
+			phy7: ethernet-phy@7 {
+				reg = <7>;
+				compatible = "ethernet-phy-ieee802.3-c22";
+			};
+		};
+
+		pip: pip@11800a0000000 {
+			interface@0 {
+				ethernet@0 {
+					phy-handle = <&phy7>;
+					rx-delay = <0>;
+					tx-delay = <0x10>;
+				};
+				ethernet@1 {
+					phy-handle = <&phy6>;
+					rx-delay = <0>;
+					tx-delay = <0x10>;
+				};
+				ethernet@2 {
+					phy-handle = <&phy5>;
+					rx-delay = <0>;
+					tx-delay = <0x10>;
+				};
+			};
+		};
+
+		uart0: serial@1180000000800 {
+			clock-frequency = <500000000>;
+		};
+
+		usbn: usbn@1180068000000 {
+			refclk-frequency = <12000000>;
+			refclk-type = "crystal";
+		};
+	};
+
+	aliases {
+		pip = &pip;
+	};
+};
diff --git a/arch/mips/boot/dts/img/Makefile b/arch/mips/boot/dts/img/Makefile
new file mode 100644
index 000000000..ebb47490b
--- /dev/null
+++ b/arch/mips/boot/dts/img/Makefile
@@ -0,0 +1,4 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_FIT_IMAGE_FDT_BOSTON)	+= boston.dtb
+
+dtb-$(CONFIG_FIT_IMAGE_FDT_MARDUK)	+= pistachio_marduk.dtb
diff --git a/arch/mips/boot/dts/img/boston.dts b/arch/mips/boot/dts/img/boston.dts
new file mode 100644
index 000000000..84328afa3
--- /dev/null
+++ b/arch/mips/boot/dts/img/boston.dts
@@ -0,0 +1,237 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include <dt-bindings/clock/boston-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/mips-gic.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "img,boston";
+
+	chosen {
+		stdout-path = "uart0:115200";
+	};
+
+	aliases {
+		uart0 = &uart0;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "img,mips";
+			reg = <0>;
+			clocks = <&clk_boston BOSTON_CLK_CPU>;
+		};
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>;
+	};
+
+	pci0: pci@10000000 {
+		compatible = "xlnx,axi-pcie-host-1.00.a";
+		device_type = "pci";
+		reg = <0x10000000 0x2000000>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SHARED 2 IRQ_TYPE_LEVEL_HIGH>;
+
+		ranges = <0x02000000 0 0x40000000
+			  0x40000000 0 0x40000000>;
+
+		bus-range = <0x00 0xff>;
+
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pci0_intc 1>,
+				<0 0 0 2 &pci0_intc 2>,
+				<0 0 0 3 &pci0_intc 3>,
+				<0 0 0 4 &pci0_intc 4>;
+
+		pci0_intc: interrupt-controller {
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+		};
+	};
+
+	pci1: pci@12000000 {
+		compatible = "xlnx,axi-pcie-host-1.00.a";
+		device_type = "pci";
+		reg = <0x12000000 0x2000000>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SHARED 1 IRQ_TYPE_LEVEL_HIGH>;
+
+		ranges = <0x02000000 0 0x20000000
+			  0x20000000 0 0x20000000>;
+
+		bus-range = <0x00 0xff>;
+
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pci1_intc 1>,
+				<0 0 0 2 &pci1_intc 2>,
+				<0 0 0 3 &pci1_intc 3>,
+				<0 0 0 4 &pci1_intc 4>;
+
+		pci1_intc: interrupt-controller {
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+		};
+	};
+
+	pci2: pci@14000000 {
+		compatible = "xlnx,axi-pcie-host-1.00.a";
+		device_type = "pci";
+		reg = <0x14000000 0x2000000>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SHARED 0 IRQ_TYPE_LEVEL_HIGH>;
+
+		ranges = <0x02000000 0 0x16000000
+			  0x16000000 0 0x100000>;
+
+		bus-range = <0x00 0xff>;
+
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pci2_intc 1>,
+				<0 0 0 2 &pci2_intc 2>,
+				<0 0 0 3 &pci2_intc 3>,
+				<0 0 0 4 &pci2_intc 4>;
+
+		pci2_intc: interrupt-controller {
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+		};
+
+		pci2_root@0,0,0 {
+			compatible = "pci10ee,7021";
+			reg = <0x00000000 0 0 0 0>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+			#interrupt-cells = <1>;
+
+			eg20t_bridge@1,0,0 {
+				compatible = "pci8086,8800";
+				reg = <0x00010000 0 0 0 0>;
+
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+
+				eg20t_phub@2,0,0 {
+					compatible = "pci8086,8801";
+					reg = <0x00020000 0 0 0 0>;
+					intel,eg20t-prefetch = <0>;
+				};
+
+				eg20t_mac@2,0,1 {
+					compatible = "pci8086,8802";
+					reg = <0x00020100 0 0 0 0>;
+					phy-reset-gpios = <&eg20t_gpio 6
+							   GPIO_ACTIVE_LOW>;
+				};
+
+				eg20t_gpio: eg20t_gpio@2,0,2 {
+					compatible = "pci8086,8803";
+					reg = <0x00020200 0 0 0 0>;
+
+					gpio-controller;
+					#gpio-cells = <2>;
+				};
+
+				eg20t_i2c@2,12,2 {
+					compatible = "pci8086,8817";
+					reg = <0x00026200 0 0 0 0>;
+
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					rtc@68 {
+						compatible = "st,m41t81s";
+						reg = <0x68>;
+					};
+				};
+			};
+		};
+	};
+
+	gic: interrupt-controller@16120000 {
+		compatible = "mti,gic";
+		reg = <0x16120000 0x20000>;
+
+		interrupt-controller;
+		#interrupt-cells = <3>;
+
+		timer {
+			compatible = "mti,gic-timer";
+			interrupts = <GIC_LOCAL 1 IRQ_TYPE_NONE>;
+			clocks = <&clk_boston BOSTON_CLK_CPU>;
+		};
+	};
+
+	cdmm@16140000 {
+		compatible = "mti,mips-cdmm";
+		reg = <0x16140000 0x8000>;
+	};
+
+	cpc@16200000 {
+		compatible = "mti,mips-cpc";
+		reg = <0x16200000 0x8000>;
+	};
+
+	plat_regs: system-controller@17ffd000 {
+		compatible = "img,boston-platform-regs", "syscon";
+		reg = <0x17ffd000 0x1000>;
+
+		clk_boston: clock {
+			compatible = "img,boston-clock";
+			#clock-cells = <1>;
+		};
+	};
+
+	reboot: syscon-reboot {
+		compatible = "syscon-reboot";
+		regmap = <&plat_regs>;
+		offset = <0x10>;
+		mask = <0x10>;
+	};
+
+	uart0: uart@17ffe000 {
+		compatible = "ns16550a";
+		reg = <0x17ffe000 0x1000>;
+		reg-shift = <2>;
+
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SHARED 3 IRQ_TYPE_LEVEL_HIGH>;
+
+		clocks = <&clk_boston BOSTON_CLK_SYS>;
+	};
+
+	lcd: lcd@17fff000 {
+		compatible = "img,boston-lcd";
+		reg = <0x17fff000 0x8>;
+	};
+};
diff --git a/arch/mips/boot/dts/img/pistachio.dtsi b/arch/mips/boot/dts/img/pistachio.dtsi
new file mode 100644
index 000000000..b1db8b8f4
--- /dev/null
+++ b/arch/mips/boot/dts/img/pistachio.dtsi
@@ -0,0 +1,930 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2015, 2016 Imagination Technologies Ltd.
+ * Copyright (C) 2015 Google, Inc.
+ */
+
+#include <dt-bindings/clock/pistachio-clk.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/mips-gic.h>
+#include <dt-bindings/reset/pistachio-resets.h>
+
+/ {
+	compatible = "img,pistachio";
+
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "mti,interaptiv";
+			reg = <0>;
+			clocks = <&clk_core CLK_MIPS_PLL>;
+			clock-names = "cpu";
+			clock-latency = <1000>;
+			operating-points = <
+				/* kHz    uV(dummy) */
+				546000 1150000
+				520000 1100000
+				494000 1000000
+				468000 950000
+				442000 900000
+				416000 800000
+			>;
+		};
+	};
+
+	i2c0: i2c@18100000 {
+		compatible = "img,scb-i2c";
+		reg = <0x18100000 0x200>;
+		interrupts = <GIC_SHARED 2 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clk_periph PERIPH_CLK_I2C0>,
+			 <&cr_periph SYS_CLK_I2C0>;
+		clock-names = "scb", "sys";
+		assigned-clocks = <&clk_periph PERIPH_CLK_I2C0_PRE_DIV>,
+				  <&clk_periph PERIPH_CLK_I2C0_DIV>;
+		assigned-clock-rates = <100000000>, <33333334>;
+		status = "disabled";
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c0_pins>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	i2c1: i2c@18100200 {
+		compatible = "img,scb-i2c";
+		reg = <0x18100200 0x200>;
+		interrupts = <GIC_SHARED 3 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clk_periph PERIPH_CLK_I2C1>,
+			 <&cr_periph SYS_CLK_I2C1>;
+		clock-names = "scb", "sys";
+		assigned-clocks = <&clk_periph PERIPH_CLK_I2C1_PRE_DIV>,
+				  <&clk_periph PERIPH_CLK_I2C1_DIV>;
+		assigned-clock-rates = <100000000>, <33333334>;
+		status = "disabled";
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c1_pins>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	i2c2: i2c@18100400 {
+		compatible = "img,scb-i2c";
+		reg = <0x18100400 0x200>;
+		interrupts = <GIC_SHARED 4 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clk_periph PERIPH_CLK_I2C2>,
+			 <&cr_periph SYS_CLK_I2C2>;
+		clock-names = "scb", "sys";
+		assigned-clocks = <&clk_periph PERIPH_CLK_I2C2_PRE_DIV>,
+				  <&clk_periph PERIPH_CLK_I2C2_DIV>;
+		assigned-clock-rates = <100000000>, <33333334>;
+		status = "disabled";
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c2_pins>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	i2c3: i2c@18100600 {
+		compatible = "img,scb-i2c";
+		reg = <0x18100600 0x200>;
+		interrupts = <GIC_SHARED 5 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clk_periph PERIPH_CLK_I2C3>,
+			 <&cr_periph SYS_CLK_I2C3>;
+		clock-names = "scb", "sys";
+		assigned-clocks = <&clk_periph PERIPH_CLK_I2C3_PRE_DIV>,
+				  <&clk_periph PERIPH_CLK_I2C3_DIV>;
+		assigned-clock-rates = <100000000>, <33333334>;
+		status = "disabled";
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c3_pins>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	i2s_in: i2s-in@18100800 {
+		compatible = "img,i2s-in";
+		reg = <0x18100800 0x200>;
+		interrupts = <GIC_SHARED 7 IRQ_TYPE_LEVEL_HIGH>;
+		dmas = <&mdc 30 0xffffffff 0>;
+		dma-names = "rx";
+		clocks = <&cr_periph SYS_CLK_I2S_IN>;
+		clock-names = "sys";
+		img,i2s-channels = <6>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2s_in_pins>;
+		status = "disabled";
+
+		#sound-dai-cells = <0>;
+	};
+
+	i2s_out: i2s-out@18100a00 {
+		compatible = "img,i2s-out";
+		reg = <0x18100a00 0x200>;
+		interrupts = <GIC_SHARED 13 IRQ_TYPE_LEVEL_HIGH>;
+		dmas = <&mdc 23 0xffffffff 0>;
+		dma-names = "tx";
+		clocks = <&cr_periph SYS_CLK_I2S_OUT>,
+			 <&clk_core CLK_I2S>;
+		clock-names = "sys", "ref";
+		assigned-clocks = <&clk_core CLK_I2S_DIV>;
+		assigned-clock-rates = <12288000>;
+		img,i2s-channels = <6>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2s_out_pins>;
+		status = "disabled";
+		resets = <&pistachio_reset PISTACHIO_RESET_I2S_OUT>;
+		reset-names = "rst";
+		#sound-dai-cells = <0>;
+	};
+
+	parallel_out: parallel-audio-out@18100c00 {
+		compatible = "img,parallel-out";
+		reg = <0x18100c00 0x100>;
+		interrupts = <GIC_SHARED 19 IRQ_TYPE_LEVEL_HIGH>;
+		dmas = <&mdc 16 0xffffffff 0>;
+		dma-names = "tx";
+		clocks = <&cr_periph SYS_CLK_PAUD_OUT>,
+			 <&clk_core CLK_AUDIO_DAC>;
+		clock-names = "sys", "ref";
+		assigned-clocks = <&clk_core CLK_AUDIO_DAC_DIV>;
+		assigned-clock-rates = <12288000>;
+		status = "disabled";
+		resets = <&pistachio_reset PISTACHIO_RESET_PRL_OUT>;
+		reset-names = "rst";
+		#sound-dai-cells = <0>;
+	};
+
+	spdif_out: spdif-out@18100d00 {
+		compatible = "img,spdif-out";
+		reg = <0x18100d00 0x100>;
+		interrupts = <GIC_SHARED 21 IRQ_TYPE_LEVEL_HIGH>;
+		dmas = <&mdc 14 0xffffffff 0>;
+		dma-names = "tx";
+		clocks = <&cr_periph SYS_CLK_SPDIF_OUT>,
+			 <&clk_core CLK_SPDIF>;
+		clock-names = "sys", "ref";
+		assigned-clocks = <&clk_core CLK_SPDIF_DIV>;
+		assigned-clock-rates = <12288000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&spdif_out_pin>;
+		status = "disabled";
+		resets = <&pistachio_reset PISTACHIO_RESET_SPDIF_OUT>;
+		reset-names = "rst";
+		#sound-dai-cells = <0>;
+	};
+
+	spdif_in: spdif-in@18100e00 {
+		compatible = "img,spdif-in";
+		reg = <0x18100e00 0x100>;
+		interrupts = <GIC_SHARED 20 IRQ_TYPE_LEVEL_HIGH>;
+		dmas = <&mdc 15 0xffffffff 0>;
+		dma-names = "rx";
+		clocks = <&cr_periph SYS_CLK_SPDIF_IN>;
+		clock-names = "sys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&spdif_in_pin>;
+		status = "disabled";
+
+		#sound-dai-cells = <0>;
+	};
+
+	internal_dac: internal-dac {
+		compatible = "img,pistachio-internal-dac";
+		img,cr-top = <&cr_top>;
+		img,voltage-select = <1>;
+
+		#sound-dai-cells = <0>;
+	};
+
+	spfi0: spi@18100f00 {
+		compatible = "img,spfi";
+		reg = <0x18100f00 0x100>;
+		interrupts = <GIC_SHARED 22 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clk_core CLK_SPI0>, <&cr_periph SYS_CLK_SPI0_MASTER>;
+		clock-names = "sys", "spfi";
+		dmas = <&mdc 9 0xffffffff 0>, <&mdc 10 0xffffffff 0>;
+		dma-names = "rx", "tx";
+		spfi-max-frequency = <50000000>;
+		status = "disabled";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	spfi1: spi@18101000 {
+		compatible = "img,spfi";
+		reg = <0x18101000 0x100>;
+		interrupts = <GIC_SHARED 26 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clk_core CLK_SPI1>, <&cr_periph SYS_CLK_SPI1>;
+		clock-names = "sys", "spfi";
+		dmas = <&mdc 1 0xffffffff 0>, <&mdc 2 0xffffffff 0>;
+		dma-names = "rx", "tx";
+		img,supports-quad-mode;
+		spfi-max-frequency = <50000000>;
+		status = "disabled";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	pwm: pwm@18101300 {
+		compatible = "img,pistachio-pwm";
+		reg = <0x18101300 0x100>;
+		clocks = <&clk_periph PERIPH_CLK_PWM>,
+			 <&cr_periph SYS_CLK_PWM>;
+		clock-names = "pwm", "sys";
+		img,cr-periph = <&cr_periph>;
+		#pwm-cells = <2>;
+		status = "disabled";
+	};
+
+	uart0: uart@18101400 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x18101400 0x100>;
+		interrupts = <GIC_SHARED 24 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clk_core CLK_UART0>, <&cr_periph SYS_CLK_UART0>;
+		clock-names = "baudclk", "apb_pclk";
+		assigned-clocks = <&clk_core CLK_UART0_INTERNAL_DIV>,
+				  <&clk_core CLK_UART0_DIV>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		pinctrl-0 = <&uart0_pins>, <&uart0_rts_cts_pins>;
+		pinctrl-names = "default";
+		status = "disabled";
+	};
+
+	uart1: uart@18101500 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x18101500 0x100>;
+		interrupts = <GIC_SHARED 25 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clk_core CLK_UART1>, <&cr_periph SYS_CLK_UART1>;
+		clock-names = "baudclk", "apb_pclk";
+		assigned-clocks = <&clk_core CLK_UART1_INTERNAL_DIV>,
+				  <&clk_core CLK_UART1_DIV>;
+		assigned-clock-rates = <114278400>, <1843200>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		pinctrl-0 = <&uart1_pins>;
+		pinctrl-names = "default";
+		status = "disabled";
+	};
+
+	adc: adc@18101600 {
+		compatible = "cosmic,10001-adc";
+		reg = <0x18101600 0x24>;
+		adc-reserved-channels = <0x30>;
+		clocks = <&clk_core CLK_AUX_ADC>;
+		clock-names = "adc";
+		assigned-clocks = <&clk_core CLK_AUX_ADC_INTERNAL_DIV>,
+				  <&clk_core CLK_AUX_ADC_DIV>;
+		assigned-clock-rates = <100000000>, <1000000>;
+		status = "disabled";
+
+		#io-channel-cells = <1>;
+	};
+
+	pinctrl: pinctrl@18101c00 {
+		compatible = "img,pistachio-system-pinctrl";
+		reg = <0x18101c00 0x400>;
+
+		gpio0: gpio0 {
+			interrupts = <GIC_SHARED 71 IRQ_TYPE_LEVEL_HIGH>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pinctrl 0 0 16>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio1: gpio1 {
+			interrupts = <GIC_SHARED 72 IRQ_TYPE_LEVEL_HIGH>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pinctrl 0 16 16>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio2: gpio2 {
+			interrupts = <GIC_SHARED 73 IRQ_TYPE_LEVEL_HIGH>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pinctrl 0 32 16>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio3: gpio3 {
+			interrupts = <GIC_SHARED 74 IRQ_TYPE_LEVEL_HIGH>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pinctrl 0 48 16>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio4: gpio4 {
+			interrupts = <GIC_SHARED 75 IRQ_TYPE_LEVEL_HIGH>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pinctrl 0 64 16>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio5: gpio5 {
+			interrupts = <GIC_SHARED 76 IRQ_TYPE_LEVEL_HIGH>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pinctrl 0 80 10>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		i2c0_pins: i2c0-pins {
+			pin_i2c0: i2c0 {
+				pins = "mfio28", "mfio29";
+				function = "i2c0";
+				drive-strength = <4>;
+			};
+		};
+
+		i2c1_pins: i2c1-pins {
+			pin_i2c1: i2c1 {
+				pins = "mfio30", "mfio31";
+				function = "i2c1";
+				drive-strength = <4>;
+			};
+		};
+
+		i2c2_pins: i2c2-pins {
+			pin_i2c2: i2c2 {
+				pins = "mfio32", "mfio33";
+				function = "i2c2";
+				drive-strength = <4>;
+			};
+		};
+
+		i2c3_pins: i2c3-pins {
+			pin_i2c3: i2c3 {
+				pins = "mfio34", "mfio35";
+				function = "i2c3";
+				drive-strength = <4>;
+			};
+		};
+
+		spim0_pins: spim0-pins {
+			pin_spim0: spim0 {
+				pins = "mfio9", "mfio10";
+				function = "spim0";
+				drive-strength = <4>;
+			};
+			spim0_clk: spim0-clk {
+				pins = "mfio8";
+				function = "spim0";
+				drive-strength = <4>;
+			};
+		};
+
+		spim0_cs0_alt_pin: spim0-cs0-alt-pin {
+			spim0-cs0 {
+				pins = "mfio2";
+				drive-strength = <2>;
+			};
+		};
+
+		spim0_cs1_pin: spim0-cs1-pin {
+			spim0-cs1 {
+				pins = "mfio1";
+				drive-strength = <2>;
+			};
+		};
+
+		spim0_cs2_pin: spim0-cs2-pin {
+			spim0-cs2 {
+				pins = "mfio55";
+				drive-strength = <2>;
+			};
+		};
+
+		spim0_cs2_alt_pin: spim0-cs2-alt-pin {
+			spim0-cs2 {
+				pins = "mfio28";
+				drive-strength = <2>;
+			};
+		};
+
+		spim0_cs3_pin: spim0-cs3-pin {
+			spim0-cs3 {
+				pins = "mfio56";
+				drive-strength = <2>;
+			};
+		};
+
+		spim0_cs3_alt_pin: spim0-cs3-alt-pin {
+			spim0-cs3 {
+				pins = "mfio29";
+				drive-strength = <2>;
+			};
+		};
+
+		spim0_cs4_pin: spim0-cs4-pin {
+			spim0-cs4 {
+				pins = "mfio57";
+				drive-strength = <2>;
+			};
+		};
+
+		spim0_cs4_alt_pin: spim0-cs4-alt-pin {
+			spim0-cs4 {
+				pins = "mfio30";
+				drive-strength = <2>;
+			};
+		};
+
+		spim1_pins: spim1-pins {
+			spim1 {
+				pins = "mfio3", "mfio4", "mfio5";
+				function = "spim1";
+				drive-strength = <2>;
+			};
+		};
+
+		spim1_quad_pins: spim1-quad-pins {
+			spim1-quad {
+				pins = "mfio6", "mfio7";
+				function = "spim1";
+				drive-strength = <2>;
+			};
+		};
+
+		spim1_cs0_pin: spim1-cs0-pins {
+			spim1-cs0 {
+				pins = "mfio0";
+				function = "spim1";
+				drive-strength = <2>;
+			};
+		};
+
+		spim1_cs1_pin: spim1-cs1-pin {
+			spim1-cs1 {
+				pins = "mfio1";
+				function = "spim1";
+				drive-strength = <2>;
+			};
+		};
+
+		spim1_cs1_alt_pin: spim1-cs1-alt-pin {
+			spim1-cs1 {
+				pins = "mfio58";
+				function = "spim1";
+				drive-strength = <2>;
+			};
+		};
+
+		spim1_cs2_pin: spim1-cs2-pin {
+			spim1-cs2 {
+				pins = "mfio2";
+				function = "spim1";
+				drive-strength = <2>;
+			};
+		};
+
+		spim1_cs2_alt0_pin: spim1-cs2-alt0-pin {
+			spim1-cs2 {
+				pins = "mfio31";
+				function = "spim1";
+				drive-strength = <2>;
+			};
+		};
+
+		spim1_cs2_alt1_pin: spim1-cs2-alt1-pin {
+			spim1-cs2 {
+				pins = "mfio55";
+				function = "spim1";
+				drive-strength = <2>;
+			};
+		};
+
+		spim1_cs3_pin: spim1-cs3-pin {
+			spim1-cs3 {
+				pins = "mfio56";
+				function = "spim1";
+				drive-strength = <2>;
+			};
+		};
+
+		spim1_cs4_pin: spim1-cs4-pin {
+			spim1-cs4 {
+				pins = "mfio57";
+				function = "spim1";
+				drive-strength = <2>;
+			};
+		};
+
+		uart0_pins: uart0-pins {
+			uart0 {
+				pins = "mfio55", "mfio56";
+				function = "uart0";
+				drive-strength = <2>;
+			};
+		};
+
+		uart0_rts_cts_pins: uart0-rts-cts-pins {
+			uart0-rts-cts {
+				pins = "mfio57", "mfio58";
+				function = "uart0";
+				drive-strength = <2>;
+			};
+		};
+
+		uart1_pins: uart1-pins {
+			uart1 {
+				pins = "mfio59", "mfio60";
+				function = "uart1";
+				drive-strength = <2>;
+			};
+		};
+
+		uart1_rts_cts_pins: uart1-rts-cts-pins {
+			uart1-rts-cts {
+				  pins = "mfio1", "mfio2";
+				  function = "uart1";
+				  drive-strength = <2>;
+			};
+		};
+
+		enet_pins: enet-pins {
+			pin_enet: enet {
+				pins = "mfio63", "mfio64", "mfio65", "mfio66",
+				       "mfio67", "mfio68", "mfio69", "mfio70";
+				function = "eth";
+				slew-rate = <1>;
+				drive-strength = <4>;
+			};
+			pin_enet_phy_clk: enet-phy-clk {
+				pins = "mfio71";
+				function = "eth";
+				slew-rate = <1>;
+				drive-strength = <8>;
+			};
+		};
+
+		sdhost_pins: sdhost-pins {
+			pin_sdhost_clk: sdhost-clk {
+				pins = "mfio15";
+				function = "sdhost";
+				slew-rate = <1>;
+				drive-strength = <4>;
+			};
+			pin_sdhost_cmd: sdhost-cmd {
+				pins = "mfio16";
+				function = "sdhost";
+				slew-rate = <1>;
+				drive-strength = <4>;
+			};
+			pin_sdhost_data: sdhost-data {
+				pins = "mfio17", "mfio18", "mfio19", "mfio20",
+				       "mfio21", "mfio22", "mfio23", "mfio24";
+				function = "sdhost";
+				slew-rate = <1>;
+				drive-strength = <4>;
+			};
+			pin_sdhost_power_select: sdhost-power-select {
+				pins = "mfio25";
+				function = "sdhost";
+				slew-rate = <1>;
+				drive-strength = <2>;
+			};
+			pin_sdhost_card_detect: sdhost-card-detect {
+				pins = "mfio26";
+				function = "sdhost";
+				drive-strength = <2>;
+			};
+			pin_sdhost_write_protect: sdhost-write-protect {
+				pins = "mfio27";
+				function = "sdhost";
+				drive-strength = <2>;
+			};
+		};
+
+		ir_pin: ir-pin {
+			ir-data {
+				pins = "mfio72";
+				function = "ir";
+				drive-strength = <2>;
+			};
+		};
+
+		pwmpdm0_pin: pwmpdm0-pin {
+			pwmpdm0 {
+				pins = "mfio73";
+				function = "pwmpdm";
+				drive-strength = <2>;
+			};
+		};
+
+		pwmpdm1_pin: pwmpdm1-pin {
+			pwmpdm1 {
+				pins = "mfio74";
+				function = "pwmpdm";
+				drive-strength = <2>;
+			};
+		};
+
+		pwmpdm2_pin: pwmpdm2-pin {
+			pwmpdm2 {
+				pins = "mfio75";
+				function = "pwmpdm";
+				drive-strength = <2>;
+			};
+		};
+
+		pwmpdm3_pin: pwmpdm3-pin {
+			pwmpdm3 {
+				pins = "mfio76";
+				function = "pwmpdm";
+				drive-strength = <2>;
+			};
+		};
+
+		dac_clk_pin: dac-clk-pin {
+			pin_dac_clk: dac-clk {
+				pins = "mfio45";
+				function = "i2s_dac_clk";
+				drive-strength = <4>;
+			};
+		};
+
+		i2s_mclk_pin: i2s-mclk-pin {
+			pin_i2s_mclk: i2s-mclk {
+				pins = "mfio36";
+				function = "i2s_out";
+				drive-strength = <4>;
+			};
+		};
+
+		spdif_out_pin: spdif-out-pin {
+			spdif-out {
+				pins = "mfio61";
+				function = "spdif_out";
+				slew-rate = <1>;
+				drive-strength = <2>;
+			};
+		};
+
+		spdif_in_pin: spdif-in-pin {
+			spdif-in {
+				pins = "mfio62";
+				function = "spdif_in";
+				drive-strength = <2>;
+			};
+		};
+
+		i2s_out_pins: i2s-out-pins {
+			pins_i2s_out_clk: i2s-out-clk {
+				pins = "mfio37", "mfio38";
+				function = "i2s_out";
+				drive-strength = <4>;
+			};
+			pins_i2s_out: i2s-out {
+				pins = "mfio39", "mfio40",
+				       "mfio41", "mfio42",
+				       "mfio43", "mfio44";
+				function = "i2s_out";
+				drive-strength = <2>;
+			};
+		};
+
+		i2s_in_pins: i2s-in-pins {
+			i2s-in {
+				pins = "mfio47", "mfio48", "mfio49",
+				       "mfio50", "mfio51", "mfio52",
+				       "mfio53", "mfio54";
+				function = "i2s_in";
+				drive-strength = <2>;
+			};
+		};
+	};
+
+	timer: timer@18102000 {
+		compatible = "img,pistachio-gptimer";
+		reg = <0x18102000 0x100>;
+		interrupts = <GIC_SHARED 60 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clk_periph PERIPH_CLK_COUNTER_FAST>,
+			 <&cr_periph SYS_CLK_TIMER>;
+		clock-names = "fast", "sys";
+		img,cr-periph = <&cr_periph>;
+	};
+
+	wdt: watchdog@18102100 {
+		compatible = "img,pdc-wdt";
+		reg = <0x18102100 0x100>;
+		interrupts = <GIC_SHARED 52 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clk_periph PERIPH_CLK_WD>, <&cr_periph SYS_CLK_WD>;
+		clock-names = "wdt", "sys";
+		assigned-clocks = <&clk_periph PERIPH_CLK_WD_PRE_DIV>,
+				  <&clk_periph PERIPH_CLK_WD_DIV>;
+		assigned-clock-rates = <4000000>, <32768>;
+	};
+
+	ir: ir@18102200 {
+		compatible = "img,ir-rev1";
+		reg = <0x18102200 0x100>;
+		interrupts = <GIC_SHARED 51 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clk_periph PERIPH_CLK_IR>, <&cr_periph SYS_CLK_IR>;
+		clock-names = "core", "sys";
+		assigned-clocks = <&clk_periph PERIPH_CLK_IR_PRE_DIV>,
+				  <&clk_periph PERIPH_CLK_IR_DIV>;
+		assigned-clock-rates = <4000000>, <32768>;
+		pinctrl-0 = <&ir_pin>;
+		pinctrl-names = "default";
+		status = "disabled";
+	};
+
+	usb: usb@18120000 {
+		compatible = "snps,dwc2";
+		reg = <0x18120000 0x1c000>;
+		interrupts = <GIC_SHARED 49 IRQ_TYPE_LEVEL_HIGH>;
+		phys = <&usb_phy>;
+		phy-names = "usb2-phy";
+		g-tx-fifo-size = <256 256 256 256>;
+		status = "disabled";
+	};
+
+	enet: ethernet@18140000 {
+		compatible = "snps,dwmac";
+		reg = <0x18140000 0x2000>;
+		interrupts = <GIC_SHARED 50 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "macirq";
+		clocks = <&clk_core CLK_ENET>, <&cr_periph SYS_CLK_ENET>;
+		clock-names = "stmmaceth", "pclk";
+		assigned-clocks = <&clk_core CLK_ENET_MUX>,
+				  <&clk_core CLK_ENET_DIV>;
+		assigned-clock-parents = <&clk_core CLK_SYS_INTERNAL_DIV>;
+		assigned-clock-rates = <0>, <50000000>;
+		pinctrl-0 = <&enet_pins>;
+		pinctrl-names = "default";
+		phy-mode = "rmii";
+		status = "disabled";
+	};
+
+	sdhost: mmc@18142000 {
+		compatible = "img,pistachio-dw-mshc";
+		reg = <0x18142000 0x400>;
+		interrupts = <GIC_SHARED 39 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clk_core CLK_SD_HOST>, <&cr_periph SYS_CLK_SD_HOST>;
+		clock-names = "ciu", "biu";
+		pinctrl-0 = <&sdhost_pins>;
+		pinctrl-names = "default";
+		fifo-depth = <0x20>;
+		clock-frequency = <50000000>;
+		bus-width = <8>;
+		cap-mmc-highspeed;
+		cap-sd-highspeed;
+		status = "disabled";
+	};
+
+	sram: sram@1b000000 {
+		compatible = "mmio-sram";
+		reg = <0x1b000000 0x10000>;
+	};
+
+	mdc: dma-controller@18143000 {
+		compatible = "img,pistachio-mdc-dma";
+		reg = <0x18143000 0x1000>;
+		interrupts = <GIC_SHARED 27 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SHARED 28 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SHARED 29 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SHARED 30 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SHARED 31 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SHARED 32 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SHARED 33 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SHARED 34 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SHARED 35 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SHARED 36 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SHARED 37 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SHARED 38 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cr_periph SYS_CLK_MDC>;
+		clock-names = "sys";
+
+		img,max-burst-multiplier = <16>;
+		img,cr-periph = <&cr_periph>;
+
+		#dma-cells = <3>;
+	};
+
+	clk_core: clk@18144000 {
+		compatible = "img,pistachio-clk", "syscon";
+		clocks = <&xtal>, <&cr_top EXT_CLK_AUDIO_IN>,
+			 <&cr_top EXT_CLK_ENET_IN>;
+		clock-names = "xtal", "audio_refclk_ext_gate",
+			      "ext_enet_in_gate";
+		reg = <0x18144000 0x800>;
+		#clock-cells = <1>;
+	};
+
+	clk_periph: clk@18144800 {
+		compatible = "img,pistachio-clk-periph";
+		reg = <0x18144800 0x1000>;
+		clocks = <&clk_core CLK_PERIPH_SYS>;
+		clock-names = "periph_sys_core";
+		#clock-cells = <1>;
+	};
+
+	cr_periph: clk@18148000 {
+		compatible = "img,pistachio-cr-periph", "syscon", "simple-bus";
+		reg = <0x18148000 0x1000>;
+		clocks = <&clk_periph PERIPH_CLK_SYS>;
+		clock-names = "sys";
+		#clock-cells = <1>;
+
+		pistachio_reset: reset-controller {
+			compatible = "img,pistachio-reset";
+			#reset-cells = <1>;
+		};
+	};
+
+	cr_top: clk@18149000 {
+		compatible = "img,pistachio-cr-top", "syscon";
+		reg = <0x18149000 0x200>;
+		#clock-cells = <1>;
+	};
+
+	hash: hash@18149600 {
+		compatible = "img,hash-accelerator";
+		reg = <0x18149600 0x100>, <0x18101100 0x4>;
+		interrupts = <GIC_SHARED 59 IRQ_TYPE_LEVEL_HIGH>;
+		dmas = <&mdc 8 0xffffffff 0>;
+		dma-names = "tx";
+		clocks = <&cr_periph SYS_CLK_HASH>,
+			 <&clk_periph PERIPH_CLK_ROM>;
+		clock-names = "sys", "hash";
+	};
+
+	gic: interrupt-controller@1bdc0000 {
+		compatible = "mti,gic";
+		reg = <0x1bdc0000 0x20000>;
+
+		interrupt-controller;
+		#interrupt-cells = <3>;
+
+		timer {
+			compatible = "mti,gic-timer";
+			interrupts = <GIC_LOCAL 1 IRQ_TYPE_NONE>;
+			clocks = <&clk_core CLK_MIPS>;
+		};
+	};
+
+	cpc: cpc@1bde0000 {
+		compatible = "mti,mips-cpc";
+		reg = <0x1bde0000 0x10000>;
+	};
+
+	cdmm: cdmm@1bdf0000 {
+		compatible = "mti,mips-cdmm";
+		reg = <0x1bdf0000 0x10000>;
+	};
+
+	usb_phy: usb-phy {
+		compatible = "img,pistachio-usb-phy";
+		clocks = <&clk_core CLK_USB_PHY>;
+		clock-names = "usb_phy";
+		assigned-clocks = <&clk_core CLK_USB_PHY_DIV>;
+		assigned-clock-rates = <50000000>;
+		img,refclk = <0x2>;
+		img,cr-top = <&cr_top>;
+		#phy-cells = <0>;
+	};
+
+	xtal: xtal {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <52000000>;
+		clock-output-names = "xtal";
+	};
+};
diff --git a/arch/mips/boot/dts/img/pistachio_marduk.dts b/arch/mips/boot/dts/img/pistachio_marduk.dts
new file mode 100644
index 000000000..a8da2f992
--- /dev/null
+++ b/arch/mips/boot/dts/img/pistachio_marduk.dts
@@ -0,0 +1,161 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2015, 2016 Imagination Technologies Ltd.
+ *
+ * IMG Marduk board is also known as Creator Ci40.
+ */
+
+/dts-v1/;
+
+#include "pistachio.dtsi"
+
+/ {
+	model = "IMG Marduk (Creator Ci40)";
+	compatible = "img,pistachio-marduk", "img,pistachio";
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+		ethernet0 = &enet;
+		spi0 = &spfi0;
+		spi1 = &spfi1;
+	};
+
+	chosen {
+		bootargs = "root=/dev/sda1 rootwait ro lpj=723968";
+		stdout-path = "serial1:115200";
+	};
+
+	memory {
+		device_type = "memory";
+		reg =  <0x00000000 0x10000000>;
+	};
+
+	reg_1v8: fixed-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "aux_adc_vref";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+	};
+
+	internal_dac_supply: internal-dac-supply {
+		compatible = "regulator-fixed";
+		regulator-name = "internal_dac_supply";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	led-controller {
+		compatible = "pwm-leds";
+
+		led-1 {
+			label = "marduk:red:heartbeat";
+			pwms = <&pwm 3 300000>;
+			max-brightness = <255>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+		button-1 {
+			label = "Button 1";
+			linux,code = <0x101>; /* BTN_1 */
+			gpios = <&gpio3 6 GPIO_ACTIVE_LOW>;
+		};
+		button-2 {
+			label = "Button 2";
+			linux,code = <0x102>; /* BTN_2 */
+			gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&internal_dac {
+	VDD-supply = <&internal_dac_supply>;
+};
+
+&spfi1 {
+	status = "okay";
+
+	pinctrl-0 = <&spim1_pins>, <&spim1_quad_pins>, <&spim1_cs0_pin>,
+		    <&spim1_cs1_pin>;
+	pinctrl-names = "default";
+	cs-gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>, <&gpio0 1 GPIO_ACTIVE_HIGH>;
+
+	flash@0 {
+		compatible = "spansion,s25fl016k", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+	assigned-clock-rates = <114278400>, <1843200>;
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&usb {
+	status = "okay";
+};
+
+&enet {
+	status = "okay";
+};
+
+&pin_enet {
+	drive-strength = <2>;
+};
+
+&pin_enet_phy_clk {
+	drive-strength = <2>;
+};
+
+&sdhost {
+	status = "okay";
+	bus-width = <4>;
+	disable-wp;
+};
+
+&pin_sdhost_cmd {
+	drive-strength = <2>;
+};
+
+&pin_sdhost_data {
+	drive-strength = <2>;
+};
+
+&pwm {
+	status = "okay";
+
+	pinctrl-0 = <&pwmpdm0_pin>, <&pwmpdm1_pin>, <&pwmpdm2_pin>,
+		    <&pwmpdm3_pin>;
+	pinctrl-names = "default";
+};
+
+&adc {
+	status = "okay";
+	vref-supply = <&reg_1v8>;
+	adc-reserved-channels = <0x10>;
+};
+
+&i2c2 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	tpm@20 {
+		compatible = "infineon,slb9645tt";
+		reg = <0x20>;
+	};
+
+};
+
+&i2c3 {
+	status = "okay";
+	clock-frequency = <400000>;
+};
diff --git a/arch/mips/boot/dts/ingenic/Makefile b/arch/mips/boot/dts/ingenic/Makefile
new file mode 100644
index 000000000..54aa0c4e6
--- /dev/null
+++ b/arch/mips/boot/dts/ingenic/Makefile
@@ -0,0 +1,9 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_JZ4740_QI_LB60)	+= qi_lb60.dtb
+dtb-$(CONFIG_JZ4740_RS90)	+= rs90.dtb
+dtb-$(CONFIG_JZ4770_GCW0)	+= gcw0.dtb
+dtb-$(CONFIG_JZ4780_CI20)	+= ci20.dtb
+dtb-$(CONFIG_X1000_CU1000_NEO)	+= cu1000-neo.dtb
+dtb-$(CONFIG_X1830_CU1830_NEO)	+= cu1830-neo.dtb
+
+obj-$(CONFIG_BUILTIN_DTB)	+= $(addsuffix .o, $(dtb-y))
diff --git a/arch/mips/boot/dts/ingenic/ci20.dts b/arch/mips/boot/dts/ingenic/ci20.dts
new file mode 100644
index 000000000..8f21d2304
--- /dev/null
+++ b/arch/mips/boot/dts/ingenic/ci20.dts
@@ -0,0 +1,598 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "jz4780.dtsi"
+#include <dt-bindings/clock/ingenic,tcu.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/regulator/active-semi,8865-regulator.h>
+
+/ {
+	compatible = "img,ci20", "ingenic,jz4780";
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+		serial3 = &uart3;
+		serial4 = &uart4;
+	};
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x10000000
+		       0x30000000 0x30000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		switch {
+			label = "ci20:sw1";
+			linux,code = <KEY_F13>;
+			gpios = <&gpd 17 GPIO_ACTIVE_HIGH>;
+			wakeup-source;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led0 {
+			label = "ci20:red:led0";
+			gpios = <&gpc 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "none";
+		};
+
+		led1 {
+			label = "ci20:red:led1";
+			gpios = <&gpc 2 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "nand-disk";
+		};
+
+		led2 {
+			label = "ci20:red:led2";
+			gpios = <&gpc 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "cpu1";
+		};
+
+		led3 {
+			label = "ci20:red:led3";
+			gpios = <&gpc 0 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "cpu0";
+		};
+	};
+
+	eth0_power: fixedregulator@0 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "eth0_power";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&gpb 25 GPIO_ACTIVE_LOW>;
+		enable-active-high;
+	};
+
+	hdmi_out: connector {
+		compatible = "hdmi-connector";
+		label = "HDMI OUT";
+		type = "a";
+
+		ddc-en-gpios = <&gpa 25 GPIO_ACTIVE_HIGH>;
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&dw_hdmi_out>;
+			};
+		};
+	};
+
+	ir: ir {
+		compatible = "gpio-ir-receiver";
+		gpios = <&gpe 3 GPIO_ACTIVE_LOW>;
+	};
+
+	wlan0_power: fixedregulator@1 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wlan0_power";
+
+		gpio = <&gpb 19 GPIO_ACTIVE_LOW>;
+		enable-active-high;
+	};
+
+	otg_power: fixedregulator@2 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "otg_power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpio = <&gpf 15 GPIO_ACTIVE_LOW>;
+		enable-active-high;
+	};
+};
+
+&ext {
+	clock-frequency = <48000000>;
+};
+
+&cgu {
+	/*
+	 * Use the 32.768 kHz oscillator as the parent of the RTC for a higher
+	 * precision.
+	 */
+	assigned-clocks = <&cgu JZ4780_CLK_OTGPHY>, <&cgu JZ4780_CLK_RTC>,
+			  <&cgu JZ4780_CLK_SSIPLL>, <&cgu JZ4780_CLK_SSI>,
+			  <&cgu JZ4780_CLK_HDMI>;
+	assigned-clock-parents = <0>, <&cgu JZ4780_CLK_RTCLK>,
+				 <&cgu JZ4780_CLK_MPLL>,
+				 <&cgu JZ4780_CLK_SSIPLL>;
+	assigned-clock-rates = <48000000>, <0>, <54000000>, <0>, <27000000>;
+};
+
+&tcu {
+	/*
+	 * 750 kHz for the system timers and clocksource,
+	 * use channel #0 and #1 for the per cpu system timers,
+	 * and use channel #2 for the clocksource.
+	 *
+	 * 3000 kHz for the OST timer to provide a higher
+	 * precision clocksource.
+	 */
+	assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER1>,
+					  <&tcu TCU_CLK_TIMER2>, <&tcu TCU_CLK_OST>;
+	assigned-clock-rates = <750000>, <750000>, <750000>, <3000000>;
+};
+
+&mmc0 {
+	status = "okay";
+
+	bus-width = <4>;
+	max-frequency = <50000000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_mmc0>;
+
+	cd-gpios = <&gpf 20 GPIO_ACTIVE_LOW>;
+};
+
+&mmc1 {
+	status = "okay";
+
+	bus-width = <4>;
+	max-frequency = <50000000>;
+	non-removable;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_mmc1>;
+
+	brcmf: wifi@1 {
+/*		reg = <4>;*/
+		compatible = "brcm,bcm4330-fmac";
+		vcc-supply = <&wlan0_power>;
+		device-wakeup-gpios = <&gpd 9 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&gpf 7 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_uart0>;
+};
+
+&uart1 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_uart1>;
+};
+
+&uart2 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_uart2>;
+	uart-has-rtscts;
+
+	bluetooth {
+		compatible = "brcm,bcm4330-bt";
+		reset-gpios = <&gpf 8 GPIO_ACTIVE_HIGH>;
+		vcc-supply = <&wlan0_power>;
+		device-wakeup-gpios = <&gpf 5 GPIO_ACTIVE_HIGH>;
+		host-wakeup-gpios = <&gpf 6 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&gpf 4 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&uart3 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_uart3>;
+};
+
+&uart4 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_uart4>;
+};
+
+&i2c0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_i2c0>;
+
+	clock-frequency = <400000>;
+
+	act8600: act8600@5a {
+		compatible = "active-semi,act8600";
+		reg = <0x5a>;
+		status = "okay";
+
+		regulators {
+			vddcore: SUDCDC1 {
+				regulator-name = "DCDC_REG1";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+			};
+			vddmem: SUDCDC2 {
+				regulator-name = "DCDC_REG2";
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+			};
+			vcc_33: SUDCDC3 {
+				regulator-name = "DCDC_REG3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+			vcc_50: SUDCDC4 {
+				regulator-name = "SUDCDC_REG4";
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5000000>;
+				regulator-always-on;
+			};
+			vcc_25: LDO_REG5 {
+				regulator-name = "LDO_REG5";
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <2500000>;
+				regulator-always-on;
+			};
+			wifi_io: LDO_REG6 {
+				regulator-name = "LDO_REG6";
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <2500000>;
+				regulator-always-on;
+			};
+			vcc_28: LDO_REG7 {
+				regulator-name = "LDO_REG7";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-always-on;
+			};
+			vcc_15: LDO_REG8 {
+				regulator-name = "LDO_REG8";
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+			};
+			vrtc_18: LDO_REG9 {
+				regulator-name = "LDO_REG9";
+				/* Despite the datasheet stating 3.3V
+				 * for REG9 and the driver expecting that,
+				 * REG9 outputs 1.8V.
+				 * Likely the CI20 uses a proprietary
+				 * factory programmed chip variant.
+				 * Since this is a simple on/off LDO the
+				 * exact values do not matter.
+				 */
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+			vcc_11: LDO_REG10 {
+				regulator-name = "LDO_REG10";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&i2c1 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_i2c1>;
+
+};
+
+&i2c2 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_i2c2>;
+
+};
+
+&i2c3 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_i2c3>;
+
+};
+
+&i2c4 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_i2c4>;
+
+	clock-frequency = <400000>;
+
+		rtc@51 {
+			compatible = "nxp,pcf8563";
+			reg = <0x51>;
+
+			interrupt-parent = <&gpf>;
+			interrupts = <30 IRQ_TYPE_LEVEL_LOW>;
+		};
+};
+
+&nemc {
+	status = "okay";
+
+	nandc: nand-controller@1 {
+		compatible = "ingenic,jz4780-nand";
+		reg = <1 0 0x1000000>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ingenic,bch-controller = <&bch>;
+
+		ingenic,nemc-tAS = <10>;
+		ingenic,nemc-tAH = <5>;
+		ingenic,nemc-tBP = <10>;
+		ingenic,nemc-tAW = <15>;
+		ingenic,nemc-tSTRV = <100>;
+
+		/*
+		 * Only CLE/ALE are needed for the devices that are connected, rather
+		 * than the full address line set.
+		 */
+		pinctrl-names = "default";
+		pinctrl-0 = <&pins_nemc>;
+
+		nand@1 {
+			reg = <1>;
+
+			nand-ecc-step-size = <1024>;
+			nand-ecc-strength = <24>;
+			nand-ecc-mode = "hw";
+			nand-on-flash-bbt;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&pins_nemc_cs1>;
+
+			partitions {
+				compatible = "fixed-partitions";
+				#address-cells = <2>;
+				#size-cells = <2>;
+
+				partition@0 {
+					label = "u-boot-spl";
+					reg = <0x0 0x0 0x0 0x800000>;
+				};
+
+				partition@800000 {
+					label = "u-boot";
+					reg = <0x0 0x800000 0x0 0x200000>;
+				};
+
+				partition@a00000 {
+					label = "u-boot-env";
+					reg = <0x0 0xa00000 0x0 0x200000>;
+				};
+
+				partition@c00000 {
+					label = "boot";
+					reg = <0x0 0xc00000 0x0 0x4000000>;
+				};
+
+				partition@4c00000 {
+					label = "system";
+					reg = <0x0 0x4c00000 0x1 0xfb400000>;
+				};
+			};
+		};
+	};
+
+	dm9000@6 {
+		compatible = "davicom,dm9000";
+		davicom,no-eeprom;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pins_nemc_cs6>;
+
+		reg = <6 0 1   /* addr */
+		       6 2 1>; /* data */
+
+		ingenic,nemc-tAS = <15>;
+		ingenic,nemc-tAH = <10>;
+		ingenic,nemc-tBP = <20>;
+		ingenic,nemc-tAW = <50>;
+		ingenic,nemc-tSTRV = <100>;
+
+		reset-gpios = <&gpf 12 GPIO_ACTIVE_LOW>;
+		vcc-supply = <&eth0_power>;
+
+		interrupt-parent = <&gpe>;
+		interrupts = <19 4>;
+
+		nvmem-cells = <&eth0_addr>;
+		nvmem-cell-names = "mac-address";
+	};
+};
+
+&bch {
+	status = "okay";
+};
+
+&otg_phy {
+	status = "okay";
+
+	vcc-supply = <&otg_power>;
+};
+
+&otg {
+	status = "okay";
+};
+
+&pinctrl {
+	pins_uart0: uart0 {
+		function = "uart0";
+		groups = "uart0-data";
+		bias-disable;
+	};
+
+	pins_uart1: uart1 {
+		function = "uart1";
+		groups = "uart1-data";
+		bias-disable;
+	};
+
+	pins_uart2: uart2 {
+		function = "uart2";
+		groups = "uart2-data", "uart2-hwflow";
+		bias-disable;
+	};
+
+	pins_uart3: uart3 {
+		function = "uart3";
+		groups = "uart3-data", "uart3-hwflow";
+		bias-disable;
+	};
+
+	pins_uart4: uart4 {
+		function = "uart4";
+		groups = "uart4-data";
+		bias-disable;
+	};
+
+	pins_i2c0: i2c0 {
+		function = "i2c0";
+		groups = "i2c0-data";
+		bias-disable;
+	};
+
+	pins_i2c1: i2c1 {
+		function = "i2c1";
+		groups = "i2c1-data";
+		bias-disable;
+	};
+
+	pins_i2c2: i2c2 {
+		function = "i2c2";
+		groups = "i2c2-data";
+		bias-disable;
+	};
+
+	pins_i2c3: i2c3 {
+		function = "i2c3";
+		groups = "i2c3-data";
+		bias-disable;
+	};
+
+	pins_i2c4: i2c4 {
+		function = "i2c4";
+		groups = "i2c4-data-e";
+		bias-disable;
+	};
+
+	pins_hdmi_ddc: hdmi_ddc {
+		function = "hdmi-ddc";
+		groups = "hdmi-ddc";
+		bias-disable;
+	};
+
+	pins_nemc: nemc {
+		function = "nemc";
+		groups = "nemc-data", "nemc-cle-ale", "nemc-rd-we", "nemc-frd-fwe";
+		bias-disable;
+	};
+
+	pins_nemc_cs1: nemc-cs1 {
+		function = "nemc-cs1";
+		groups = "nemc-cs1";
+		bias-disable;
+	};
+
+	pins_nemc_cs6: nemc-cs6 {
+		function = "nemc-cs6";
+		groups = "nemc-cs6";
+		bias-disable;
+	};
+
+	pins_mmc0: mmc0 {
+		function = "mmc0";
+		groups = "mmc0-1bit-e", "mmc0-4bit-e";
+		bias-disable;
+	};
+
+	pins_mmc1: mmc1 {
+		function = "mmc1";
+		groups = "mmc1-1bit-d", "mmc1-4bit-d";
+		bias-disable;
+	};
+};
+
+&hdmi {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_hdmi_ddc>;
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			dw_hdmi_in: endpoint {
+				remote-endpoint = <&lcd_out>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+			dw_hdmi_out: endpoint {
+				remote-endpoint = <&hdmi_con>;
+			};
+		};
+	};
+};
+
+&lcdc0 {
+	status = "okay";
+
+	port {
+		lcd_out: endpoint {
+			remote-endpoint = <&dw_hdmi_in>;
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/ingenic/cu1000-neo.dts b/arch/mips/boot/dts/ingenic/cu1000-neo.dts
new file mode 100644
index 000000000..c89abf94e
--- /dev/null
+++ b/arch/mips/boot/dts/ingenic/cu1000-neo.dts
@@ -0,0 +1,221 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "x1000.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/ingenic,sysost.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "yna,cu1000-neo", "ingenic,x1000e";
+	model = "YSH & ATIL General Board CU1000-Neo";
+
+	aliases {
+		serial2 = &uart2;
+	};
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x04000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-0 {
+			gpios = <&gpb 21 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+		};
+	};
+
+	wlan_pwrseq: msc1-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+
+		reset-gpios = <&gpc 17 GPIO_ACTIVE_LOW>;
+		post-power-on-delay-ms = <200>;
+	};
+};
+
+&exclk {
+	clock-frequency = <24000000>;
+};
+
+&cgu {
+	/*
+	 * Use the 32.768 kHz oscillator as the parent of the RTC for a higher
+	 * precision.
+	 */
+	assigned-clocks = <&cgu X1000_CLK_RTC>;
+	assigned-clock-parents = <&cgu X1000_CLK_RTCLK>;
+};
+
+&ost {
+	/* 1500 kHz for the system timer and clocksource */
+	assigned-clocks = <&ost OST_CLK_EVENT_TIMER>, <&ost OST_CLK_GLOBAL_TIMER>;
+	assigned-clock-rates = <1500000>, <1500000>;
+};
+
+&uart2 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_uart2>;
+};
+
+&ssi {
+	status = "okay";
+
+	num-cs = <2>;
+	cs-gpios = <0>, <&gpc 20 GPIO_ACTIVE_LOW>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_ssi>;
+
+	sc16is752: expander@0 {
+		compatible = "nxp,sc16is752";
+		reg = <0>; /* CE0 */
+
+		spi-rx-bus-width = <1>;
+		spi-tx-bus-width = <1>;
+		spi-max-frequency = <4000000>;
+
+		clocks = <&exclk_sc16is752>;
+
+		interrupt-parent = <&gpc>;
+		interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		exclk_sc16is752: sc16is752 {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <48000000>;
+		};
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	clock-frequency = <400000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_i2c0>;
+
+	ads7830: adc@48 {
+		compatible = "ti,ads7830";
+		reg = <0x48>;
+	};
+};
+
+&msc0 {
+	status = "okay";
+
+	bus-width = <8>;
+	max-frequency = <50000000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_msc0>;
+
+	non-removable;
+};
+
+&msc1 {
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	bus-width = <4>;
+	max-frequency = <50000000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_msc1>;
+
+	non-removable;
+
+	mmc-pwrseq = <&wlan_pwrseq>;
+
+	ap6212a: wifi@1 {
+		compatible = "brcm,bcm4329-fmac";
+		reg = <1>;
+
+		interrupt-parent = <&gpc>;
+		interrupts = <16 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-names = "host-wake";
+
+		brcm,drive-strength = <10>;
+	};
+};
+
+&mac {
+	status = "okay";
+
+	phy-mode = "rmii";
+	phy-handle = <&lan8720a>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_mac>;
+
+	snps,reset-gpio = <&gpc 23 GPIO_ACTIVE_LOW>; /* PC23 */
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 30000>;
+};
+
+&mdio {
+	status = "okay";
+
+	lan8720a: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0007.c0f0", "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&otg_phy {
+	status = "okay";
+};
+
+&otg {
+	status = "okay";
+};
+
+&pinctrl {
+	pins_uart2: uart2 {
+		function = "uart2";
+		groups = "uart2-data-d";
+		bias-pull-up;
+	};
+
+	pins_ssi: ssi {
+		function = "ssi";
+		groups = "ssi-dt-d", "ssi-dr-d", "ssi-clk-d", "ssi-ce0-d";
+		bias-disable;
+	};
+
+	pins_i2c0: i2c0 {
+		function = "i2c0";
+		groups = "i2c0-data";
+		bias-pull-up;
+	};
+
+	pins_msc0: msc0 {
+		function = "mmc0";
+		groups = "mmc0-1bit", "mmc0-4bit", "mmc0-8bit";
+		bias-disable;
+	};
+
+	pins_msc1: msc1 {
+		function = "mmc1";
+		groups = "mmc1-1bit", "mmc1-4bit";
+		bias-disable;
+	};
+
+	pins_mac: mac {
+		function = "mac";
+		groups = "mac";
+		bias-disable;
+	};
+};
diff --git a/arch/mips/boot/dts/ingenic/cu1830-neo.dts b/arch/mips/boot/dts/ingenic/cu1830-neo.dts
new file mode 100644
index 000000000..3c7784983
--- /dev/null
+++ b/arch/mips/boot/dts/ingenic/cu1830-neo.dts
@@ -0,0 +1,224 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "x1830.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/ingenic,sysost.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "yna,cu1830-neo", "ingenic,x1830";
+	model = "YSH & ATIL General Board CU1830-Neo";
+
+	aliases {
+		serial1 = &uart1;
+	};
+
+	chosen {
+		stdout-path = "serial1:115200n8";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-0 {
+			gpios = <&gpc 17 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+		};
+	};
+
+	wlan_pwrseq: msc1-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+
+		reset-gpios = <&gpc 13 GPIO_ACTIVE_LOW>;
+		post-power-on-delay-ms = <200>;
+	};
+};
+
+&exclk {
+	clock-frequency = <24000000>;
+};
+
+&cgu {
+	/*
+	 * Use the 32.768 kHz oscillator as the parent of the RTC for a higher
+	 * precision.
+	 */
+	assigned-clocks = <&cgu X1830_CLK_RTC>;
+	assigned-clock-parents = <&cgu X1830_CLK_RTCLK>;
+};
+
+&ost {
+	/* 1500 kHz for the system timer and clocksource */
+	assigned-clocks = <&ost OST_CLK_EVENT_TIMER>, <&ost OST_CLK_GLOBAL_TIMER>;
+	assigned-clock-rates = <1500000>, <1500000>;
+};
+
+&uart1 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_uart1>;
+};
+
+&ssi0 {
+	status = "okay";
+
+	num-cs = <2>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_ssi0>;
+
+	sc16is752: expander@0 {
+		compatible = "nxp,sc16is752";
+		reg = <0>; /* CE0 */
+
+		spi-rx-bus-width = <1>;
+		spi-tx-bus-width = <1>;
+		spi-max-frequency = <4000000>;
+
+		clocks = <&exclk_sc16is752>;
+
+		interrupt-parent = <&gpb>;
+		interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		exclk_sc16is752: sc16is752 {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <48000000>;
+		};
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	clock-frequency = <400000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_i2c0>;
+
+	ads7830: adc@48 {
+		compatible = "ti,ads7830";
+		reg = <0x48>;
+	};
+};
+
+&dtrng {
+	status = "okay";
+};
+
+&msc0 {
+	status = "okay";
+
+	bus-width = <4>;
+	max-frequency = <50000000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_msc0>;
+
+	non-removable;
+};
+
+&msc1 {
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	bus-width = <4>;
+	max-frequency = <50000000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_msc1>;
+
+	non-removable;
+
+	mmc-pwrseq = <&wlan_pwrseq>;
+
+	ap6212a: wifi@1 {
+		compatible = "brcm,bcm4329-fmac";
+		reg = <1>;
+
+		interrupt-parent = <&gpc>;
+		interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-names = "host-wake";
+
+		brcm,drive-strength = <10>;
+	};
+};
+
+&mac {
+	status = "okay";
+
+	phy-mode = "rmii";
+	phy-handle = <&ip101gr>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_mac>;
+
+	snps,reset-gpio = <&gpb 28 GPIO_ACTIVE_LOW>; /* PB28 */
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 30000>;
+};
+
+&mdio {
+	status = "okay";
+
+	ip101gr: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0243.0c54", "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&otg_phy {
+	status = "okay";
+};
+
+&otg {
+	status = "okay";
+};
+
+&pinctrl {
+	pins_uart1: uart1 {
+		function = "uart1";
+		groups = "uart1-data";
+		bias-pull-up;
+	};
+
+	pins_ssi0: ssi0 {
+		function = "ssi0";
+		groups = "ssi0-dt", "ssi0-dr", "ssi0-clk", "ssi0-ce0", "ssi0-ce1";
+		bias-disable;
+	};
+
+	pins_i2c0: i2c0 {
+		function = "i2c0";
+		groups = "i2c0-data";
+		bias-pull-up;
+	};
+
+	pins_msc0: msc0 {
+		function = "mmc0";
+		groups = "mmc0-1bit", "mmc0-4bit";
+		bias-disable;
+	};
+
+	pins_msc1: msc1 {
+		function = "mmc1";
+		groups = "mmc1-1bit", "mmc1-4bit";
+		bias-disable;
+	};
+
+	pins_mac: mac {
+		function = "mac";
+		groups = "mac";
+		bias-disable;
+	};
+};
diff --git a/arch/mips/boot/dts/ingenic/gcw0.dts b/arch/mips/boot/dts/ingenic/gcw0.dts
new file mode 100644
index 000000000..5d33f26fd
--- /dev/null
+++ b/arch/mips/boot/dts/ingenic/gcw0.dts
@@ -0,0 +1,542 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "jz4770.dtsi"
+#include <dt-bindings/clock/ingenic,tcu.h>
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/iio/adc/ingenic,adc.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	compatible = "gcw,zero", "ingenic,jz4770";
+	model = "GCW Zero";
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+		serial2 = &uart2;
+		serial3 = &uart3;
+	};
+
+	memory: memory {
+		device_type = "memory";
+		reg = <0x0 0x10000000>,
+		      <0x30000000 0x10000000>;
+	};
+
+	chosen {
+		stdout-path = "serial2:57600n8";
+	};
+
+	vcc: regulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc";
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	mmc1_power: regulator@1 {
+		compatible = "regulator-fixed";
+		regulator-name = "mmc1_vcc";
+		gpio = <&gpe 9 0>;
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc>;
+	};
+
+	headphones_amp: analog-amplifier@0 {
+		compatible = "simple-audio-amplifier";
+		enable-gpios = <&gpf 3 GPIO_ACTIVE_LOW>;
+		enable-delay-ms = <50>;
+
+		VCC-supply = <&ldo5>;
+		sound-name-prefix = "Headphones Amp";
+	};
+
+	speaker_amp: analog-amplifier@1 {
+		compatible = "simple-audio-amplifier";
+		enable-gpios = <&gpf 20 GPIO_ACTIVE_HIGH>;
+
+		VCC-supply = <&ldo5>;
+		sound-name-prefix = "Speaker Amp";
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+
+		simple-audio-card,name = "gcw0-audio";
+		simple-audio-card,format = "i2s";
+
+		simple-audio-card,widgets =
+			"Speaker", "Speaker",
+			"Headphone", "Headphones",
+			"Microphone", "Built-in Mic";
+		simple-audio-card,routing =
+			"Headphones Amp INL", "LHPOUT",
+			"Headphones Amp INR", "RHPOUT",
+			"Headphones", "Headphones Amp OUTL",
+			"Headphones", "Headphones Amp OUTR",
+			"Speaker Amp INL", "LOUT",
+			"Speaker Amp INR", "ROUT",
+			"Speaker", "Speaker Amp OUTL",
+			"Speaker", "Speaker Amp OUTR",
+			"LLINEIN", "Cap-less",
+			"RLINEIN", "Cap-less",
+			"Built-in Mic", "MICBIAS",
+			"MIC1P", "Built-in Mic",
+			"MIC1N", "Built-in Mic";
+		simple-audio-card,pin-switches = "Speaker", "Headphones";
+
+		simple-audio-card,hp-det-gpio = <&gpf 21 GPIO_ACTIVE_LOW>;
+		simple-audio-card,aux-devs = <&speaker_amp>, <&headphones_amp>;
+
+		simple-audio-card,bitclock-master = <&dai_codec>;
+		simple-audio-card,frame-master = <&dai_codec>;
+
+		dai_cpu: simple-audio-card,cpu {
+			sound-dai = <&aic>;
+		};
+
+		dai_codec: simple-audio-card,codec {
+			sound-dai = <&codec>;
+		};
+	};
+
+	rumble {
+		compatible = "pwm-vibrator";
+		pwms = <&pwm 4 2000000 0>;
+		pwm-names = "enable";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pins_pwm4>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 1 40000 0>;
+		power-supply = <&vcc>;
+
+		brightness-levels = <0 16 32 48 64 80 96 112 128
+				     144 160 176 192 208 224 240 255>;
+		default-brightness-level = <12>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pins_pwm1>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		button-0 {
+			label = "D-pad up";
+			linux,code = <KEY_UP>;
+			linux,can-disable;
+			gpios = <&gpe 21 GPIO_ACTIVE_LOW>;
+		};
+
+		button-1 {
+			label = "D-pad down";
+			linux,code = <KEY_DOWN>;
+			linux,can-disable;
+			gpios = <&gpe 25 GPIO_ACTIVE_LOW>;
+		};
+
+		button-2 {
+			label = "D-pad left";
+			linux,code = <KEY_LEFT>;
+			linux,can-disable;
+			gpios = <&gpe 23 GPIO_ACTIVE_LOW>;
+		};
+
+		button-3 {
+			label = "D-pad right";
+			linux,code = <KEY_RIGHT>;
+			linux,can-disable;
+			gpios = <&gpe 24 GPIO_ACTIVE_LOW>;
+		};
+
+		button-4 {
+			label = "Button A";
+			linux,code = <KEY_LEFTCTRL>;
+			linux,can-disable;
+			gpios = <&gpe 29 GPIO_ACTIVE_LOW>;
+		};
+
+		button-5 {
+			label = "Button B";
+			linux,code = <KEY_LEFTALT>;
+			linux,can-disable;
+			gpios = <&gpe 20 GPIO_ACTIVE_LOW>;
+		};
+
+		button-6 {
+			label = "Button Y";
+			linux,code = <KEY_SPACE>;
+			linux,can-disable;
+			gpios = <&gpe 27 GPIO_ACTIVE_LOW>;
+		};
+
+		button-7 {
+			label = "Button X";
+			linux,code = <KEY_LEFTSHIFT>;
+			linux,can-disable;
+			gpios = <&gpe 28 GPIO_ACTIVE_LOW>;
+		};
+
+		button-8 {
+			label = "Left shoulder button";
+			linux,code = <KEY_TAB>;
+			linux,can-disable;
+			gpios = <&gpb 20 GPIO_ACTIVE_LOW>;
+		};
+
+		button-9 {
+			label = "Right shoulder button";
+			linux,code = <KEY_BACKSPACE>;
+			linux,can-disable;
+			gpios = <&gpe 26 GPIO_ACTIVE_LOW>;
+		};
+
+		button-10 {
+			label = "Start button";
+			linux,code = <KEY_ENTER>;
+			linux,can-disable;
+			gpios = <&gpb 21 GPIO_ACTIVE_LOW>;
+		};
+
+		button-11 {
+			label = "Select button";
+			linux,code = <KEY_ESC>;
+			linux,can-disable;
+			/*
+			 * This is the only button that is active high,
+			 * since it doubles as BOOT_SEL1.
+			 */
+			gpios = <&gpd 18 GPIO_ACTIVE_HIGH>;
+		};
+
+		button-12 {
+			label = "Power slider";
+			linux,code = <KEY_POWER>;
+			linux,can-disable;
+			gpios = <&gpa 30 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+
+		button-13 {
+			label = "Power hold";
+			linux,code = <KEY_PAUSE>;
+			linux,can-disable;
+			gpios = <&gpf 11 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	i2c3: i2c-controller@3 {
+		compatible = "i2c-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		sda-gpios = <&gpd 5 GPIO_ACTIVE_HIGH>;
+		scl-gpios = <&gpd 4 GPIO_ACTIVE_HIGH>;
+		i2c-gpio,delay-us = <2>; /* 250 kHz */
+
+		act8600: pmic@5a {
+			compatible = "active-semi,act8600";
+			reg = <0x5a>;
+
+			regulators {
+				/* USB OTG */
+				otg_vbus: SUDCDC_REG4 {
+					/*
+					 * 5.3V instead of 5.0V to compensate
+					 * for the voltage drop of a diode
+					 * between the regulator and the
+					 * connector.
+					 */
+					regulator-min-microvolt = <5300000>;
+					regulator-max-microvolt = <5300000>;
+					inl-supply = <&vcc>;
+				};
+
+				/*
+				 * When this is off, there is no sound, but also
+				 * no USB networking.
+				 */
+				ldo5: LDO5 {
+					regulator-min-microvolt = <2500000>;
+					regulator-max-microvolt = <2500000>;
+					inl-supply = <&vcc>;
+				};
+
+				/* LCD panel and FM radio */
+				ldo6: LDO6 {
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					inl-supply = <&vcc>;
+				};
+
+				/* ??? */
+				LDO7 {
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					/*regulator-always-on;*/
+					inl-supply = <&vcc>;
+				};
+
+				/*
+				 * The colors on the LCD are wrong when this is
+				 * off. Which is strange, since the LCD panel
+				 * data sheet only mentions a 3.3V input.
+				 */
+				LDO8 {
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					inl-supply = <&vcc>;
+				};
+
+				/* RTC fixed 3.3V */
+				LDO_REG9 {
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+					inl-supply = <&vcc>;
+				};
+
+				/* Unused fixed 1.2V */
+				LDO_REG10 {
+					inl-supply = <&vcc>;
+				};
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led {
+			gpios = <&gpb 30 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+	};
+
+	spi {
+		compatible = "spi-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		sck-gpios = <&gpe 15 GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpe 17 GPIO_ACTIVE_HIGH>;
+		cs-gpios = <&gpe 16 GPIO_ACTIVE_HIGH>;
+		num-chipselects = <1>;
+
+		nt39016@0 {
+			compatible = "kingdisplay,kd035g6-54nt";
+			reg = <0>;
+
+			spi-max-frequency = <3125000>;
+			spi-3wire;
+
+			reset-gpios = <&gpe 2 GPIO_ACTIVE_LOW>;
+
+			backlight = <&backlight>;
+			power-supply = <&ldo6>;
+
+			port {
+				panel_input: endpoint {
+					remote-endpoint = <&panel_output>;
+				};
+			};
+		};
+	};
+
+	connector {
+		compatible = "gpio-usb-b-connector", "usb-b-connector";
+		label = "mini-USB";
+		type = "mini";
+
+		/*
+		 * USB OTG is not yet working reliably, the ID detection
+		 * mechanism tends to fry easily for unknown reasons.
+		 * Until this is fixed, disable OTG by not providing the
+		 * ID GPIO to the driver.
+		 */
+		//id-gpios = <&gpf 18 GPIO_ACTIVE_LOW>;
+
+		vbus-gpios = <&gpb 5 GPIO_ACTIVE_HIGH>;
+		vbus-supply = <&otg_vbus>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pins_otg>;
+
+		port {
+			usb_ep: endpoint {
+				remote-endpoint = <&usb_otg_ep>;
+			};
+		};
+	};
+};
+
+&ext {
+	clock-frequency = <12000000>;
+};
+
+&pinctrl {
+	pins_lcd: lcd {
+		function = "lcd";
+		groups = "lcd-24bit";
+	};
+
+	pins_uart2: uart2 {
+		function = "uart2";
+		groups = "uart2-data";
+	};
+
+	pins_mmc0: mmc0 {
+		function = "mmc0";
+		groups = "mmc0-1bit-a", "mmc0-4bit-a";
+	};
+
+	pins_mmc1: mmc1 {
+		function = "mmc1";
+		groups = "mmc1-1bit-d", "mmc1-4bit-d";
+	};
+
+	pins_otg: otg {
+		otg-vbus-pin {
+			function = "otg";
+			groups = "otg-vbus";
+		};
+
+		vbus-pin {
+			pins = "PB5";
+			bias-disable;
+		};
+	};
+
+	pins_pwm1: pwm1 {
+		function = "pwm1";
+		groups = "pwm1";
+	};
+
+	pins_pwm4: pwm4 {
+		function = "pwm4";
+		groups = "pwm4";
+	};
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_uart2>;
+
+	status = "okay";
+};
+
+&cgu {
+	/*
+	 * Put high-speed peripherals under PLL1, such that we can change the
+	 * PLL0 frequency on demand without having to suspend peripherals.
+	 * We use a rate of 432 MHz, which is the least common multiple of
+	 * 27 MHz (required by TV encoder) and 48 MHz (required by USB host).
+	 * Put the GPU under PLL0 since we want a higher frequency.
+	 * Use the 32 kHz oscillator as the parent of the RTC for a higher
+	 * precision.
+	 */
+	assigned-clocks =
+		<&cgu JZ4770_CLK_PLL1>,
+		<&cgu JZ4770_CLK_GPU>,
+		<&cgu JZ4770_CLK_RTC>,
+		<&cgu JZ4770_CLK_UHC>,
+		<&cgu JZ4770_CLK_LPCLK_MUX>,
+		<&cgu JZ4770_CLK_MMC0_MUX>,
+		<&cgu JZ4770_CLK_MMC1_MUX>;
+	assigned-clock-parents =
+		<0>,
+		<&cgu JZ4770_CLK_PLL0>,
+		<&cgu JZ4770_CLK_OSC32K>,
+		<&cgu JZ4770_CLK_PLL1>,
+		<&cgu JZ4770_CLK_PLL1>,
+		<&cgu JZ4770_CLK_PLL1>,
+		<&cgu JZ4770_CLK_PLL1>;
+	assigned-clock-rates =
+		<432000000>,
+		<600000000>;
+};
+
+&uhc {
+	/* The WiFi module is connected to the UHC. */
+	status = "okay";
+};
+
+&tcu {
+	/*
+	 * 750 kHz for the system timer and clocksource, 12 MHz for the OST,
+	 * and use RTC as the parent for the watchdog clock
+	 */
+	assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER2>,
+			  <&tcu TCU_CLK_OST>, <&tcu TCU_CLK_WDT>;
+	assigned-clock-parents = <0>, <0>, <0>, <&cgu JZ4770_CLK_RTC>;
+	assigned-clock-rates = <750000>, <750000>, <12000000>;
+
+	/* PWM1 is in use, so use channel #2 for the clocksource */
+	ingenic,pwm-channels-mask = <0xfa>;
+};
+
+&usb_otg {
+	port {
+		usb_otg_ep: endpoint {
+			remote-endpoint = <&usb_ep>;
+		};
+	};
+};
+
+&otg_phy {
+	vcc-supply = <&ldo5>;
+};
+
+&rtc {
+	clocks = <&cgu JZ4770_CLK_RTC>;
+	clock-names = "rtc";
+
+	system-power-controller;
+};
+
+&mmc0 {
+	status = "okay";
+
+	bus-width = <4>;
+	max-frequency = <48000000>;
+	vmmc-supply = <&vcc>;
+	non-removable;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_mmc0>;
+};
+
+&mmc1 {
+	status = "okay";
+
+	bus-width = <4>;
+	max-frequency = <48000000>;
+	cd-gpios = <&gpb 2 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&mmc1_power>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_mmc1>;
+};
+
+&lcd {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_lcd>;
+
+	port {
+		panel_output: endpoint {
+			remote-endpoint = <&panel_input>;
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/ingenic/gcw0_proto.dts b/arch/mips/boot/dts/ingenic/gcw0_proto.dts
new file mode 100644
index 000000000..02df22f8a
--- /dev/null
+++ b/arch/mips/boot/dts/ingenic/gcw0_proto.dts
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "gcw0.dts"
+
+/ {
+	model = "GCW Zero Prototype";
+};
+
+&memory {
+	/* Prototype has only 256 MiB of RAM */
+	reg = <0x0 0x10000000>;
+};
diff --git a/arch/mips/boot/dts/ingenic/jz4725b.dtsi b/arch/mips/boot/dts/ingenic/jz4725b.dtsi
new file mode 100644
index 000000000..e9e48022f
--- /dev/null
+++ b/arch/mips/boot/dts/ingenic/jz4725b.dtsi
@@ -0,0 +1,378 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/clock/ingenic,jz4725b-cgu.h>
+#include <dt-bindings/clock/ingenic,tcu.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "ingenic,jz4725b";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "ingenic,xburst-mxu1.0";
+			reg = <0>;
+
+			clocks = <&cgu JZ4725B_CLK_CCLK>;
+			clock-names = "cpu";
+		};
+	};
+
+	cpuintc: interrupt-controller {
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		compatible = "mti,cpu-interrupt-controller";
+	};
+
+	intc: interrupt-controller@10001000 {
+		compatible = "ingenic,jz4725b-intc", "ingenic,jz4740-intc";
+		reg = <0x10001000 0x14>;
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&cpuintc>;
+		interrupts = <2>;
+	};
+
+	ext: ext {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+	};
+
+	osc32k: osc32k {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+	};
+
+	cgu: clock-controller@10000000 {
+		compatible = "ingenic,jz4725b-cgu";
+		reg = <0x10000000 0x100>;
+
+		clocks = <&ext>, <&osc32k>;
+		clock-names = "ext", "osc32k";
+
+		#clock-cells = <1>;
+	};
+
+	tcu: timer@10002000 {
+		compatible = "ingenic,jz4725b-tcu", "simple-mfd";
+		reg = <0x10002000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x10002000 0x1000>;
+
+		#clock-cells = <1>;
+
+		clocks = <&cgu JZ4725B_CLK_RTC>,
+			 <&cgu JZ4725B_CLK_EXT>,
+			 <&cgu JZ4725B_CLK_PCLK>,
+			 <&cgu JZ4725B_CLK_TCU>;
+		clock-names = "rtc", "ext", "pclk", "tcu";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <23>, <22>, <21>;
+
+		watchdog: watchdog@0 {
+			compatible = "ingenic,jz4725b-watchdog", "ingenic,jz4740-watchdog";
+			reg = <0x0 0xc>;
+
+			clocks = <&tcu TCU_CLK_WDT>;
+			clock-names = "wdt";
+		};
+
+		pwm: pwm@60 {
+			compatible = "ingenic,jz4725b-pwm";
+			reg = <0x60 0x40>;
+
+			#pwm-cells = <3>;
+
+			clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER1>,
+				 <&tcu TCU_CLK_TIMER2>, <&tcu TCU_CLK_TIMER3>,
+				 <&tcu TCU_CLK_TIMER4>, <&tcu TCU_CLK_TIMER5>;
+			clock-names = "timer0", "timer1", "timer2",
+				      "timer3", "timer4", "timer5";
+		};
+
+		ost: timer@e0 {
+			compatible = "ingenic,jz4725b-ost";
+			reg = <0xe0 0x20>;
+
+			clocks = <&tcu TCU_CLK_OST>;
+			clock-names = "ost";
+
+			interrupts = <15>;
+		};
+	};
+
+	rtc_dev: rtc@10003000 {
+		compatible = "ingenic,jz4725b-rtc", "ingenic,jz4740-rtc";
+		reg = <0x10003000 0x40>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <6>;
+
+		clocks = <&cgu JZ4725B_CLK_RTC>;
+		clock-names = "rtc";
+	};
+
+	pinctrl: pinctrl@10010000 {
+		compatible = "ingenic,jz4725b-pinctrl";
+		reg = <0x10010000 0x400>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpa: gpio@0 {
+			compatible = "ingenic,jz4725b-gpio";
+			reg = <0>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 0 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <16>;
+		};
+
+		gpb: gpio@1 {
+			compatible = "ingenic,jz4725b-gpio";
+			reg = <1>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 32 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <15>;
+		};
+
+		gpc: gpio@2 {
+			compatible = "ingenic,jz4725b-gpio";
+			reg = <2>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 64 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <14>;
+		};
+
+		gpd: gpio@3 {
+			compatible = "ingenic,jz4725b-gpio";
+			reg = <3>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 96 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <13>;
+		};
+	};
+
+	aic: audio-controller@10020000 {
+		compatible = "ingenic,jz4725b-i2s", "ingenic,jz4740-i2s";
+		reg = <0x10020000 0x38>;
+
+		#sound-dai-cells = <0>;
+
+		clocks = <&cgu JZ4725B_CLK_AIC>,
+			 <&cgu JZ4725B_CLK_I2S>,
+			 <&cgu JZ4725B_CLK_EXT>,
+			 <&cgu JZ4725B_CLK_PLL_HALF>;
+		clock-names = "aic", "i2s", "ext", "pll half";
+
+		interrupt-parent = <&intc>;
+		interrupts = <10>;
+
+		dmas = <&dmac 25 0xffffffff>, <&dmac 24 0xffffffff>;
+		dma-names = "rx", "tx";
+	};
+
+	codec: audio-codec@100200a4 {
+		compatible = "ingenic,jz4725b-codec";
+		reg = <0x100200a4 0x8>;
+
+		#sound-dai-cells = <0>;
+
+		clocks = <&cgu JZ4725B_CLK_AIC>;
+		clock-names = "aic";
+	};
+
+	mmc0: mmc@10021000 {
+		compatible = "ingenic,jz4725b-mmc";
+		reg = <0x10021000 0x1000>;
+
+		clocks = <&cgu JZ4725B_CLK_MMC0>;
+		clock-names = "mmc";
+
+		interrupt-parent = <&intc>;
+		interrupts = <25>;
+
+		dmas = <&dmac 27 0xffffffff>, <&dmac 26 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		cap-sd-highspeed;
+		cap-mmc-highspeed;
+		cap-sdio-irq;
+	};
+
+	mmc1: mmc@10022000 {
+		compatible = "ingenic,jz4725b-mmc";
+		reg = <0x10022000 0x1000>;
+
+		clocks = <&cgu JZ4725B_CLK_MMC1>;
+		clock-names = "mmc";
+
+		interrupt-parent = <&intc>;
+		interrupts = <24>;
+
+		dmas = <&dmac 31 0xffffffff>, <&dmac 30 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		cap-sd-highspeed;
+		cap-mmc-highspeed;
+		cap-sdio-irq;
+	};
+
+	uart: serial@10030000 {
+		compatible = "ingenic,jz4725b-uart", "ingenic,jz4740-uart";
+		reg = <0x10030000 0x100>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <9>;
+
+		clocks = <&ext>, <&cgu JZ4725B_CLK_UART>;
+		clock-names = "baud", "module";
+	};
+
+	adc: adc@10070000 {
+		compatible = "ingenic,jz4725b-adc";
+		#io-channel-cells = <1>;
+
+		reg = <0x10070000 0x30>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x10070000 0x30>;
+
+		clocks = <&cgu JZ4725B_CLK_ADC>;
+		clock-names = "adc";
+
+		interrupt-parent = <&intc>;
+		interrupts = <18>;
+	};
+
+	nemc: memory-controller@13010000 {
+		compatible = "ingenic,jz4725b-nemc", "ingenic,jz4740-nemc";
+		reg = <0x13010000 0x10000>;
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges = <1 0 0x18000000 0x4000000>, <2 0 0x14000000 0x4000000>,
+			 <3 0 0x0c000000 0x4000000>, <4 0 0x08000000 0x4000000>;
+
+		clocks = <&cgu JZ4725B_CLK_MCLK>;
+	};
+
+	dmac: dma-controller@13020000 {
+		compatible = "ingenic,jz4725b-dma";
+		reg = <0x13020000 0xd8>, <0x13020300 0x14>;
+
+		#dma-cells = <2>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <29>;
+
+		clocks = <&cgu JZ4725B_CLK_DMA>;
+	};
+
+	udc: usb@13040000 {
+		compatible = "ingenic,jz4725b-musb", "ingenic,jz4740-musb";
+		reg = <0x13040000 0x10000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <27>;
+		interrupt-names = "mc";
+
+		clocks = <&cgu JZ4725B_CLK_UDC>;
+		clock-names = "udc";
+	};
+
+	lcd: lcd-controller@13050000 {
+		compatible = "ingenic,jz4725b-lcd";
+		reg = <0x13050000 0x130>; /* tbc */
+
+		interrupt-parent = <&intc>;
+		interrupts = <31>;
+
+		clocks = <&cgu JZ4725B_CLK_LCD>;
+		clock-names = "lcd_pclk";
+
+		lcd_ports: ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@8 {
+				reg = <8>;
+
+				ipu_output: endpoint {
+					remote-endpoint = <&ipu_input>;
+				};
+			};
+		};
+	};
+
+	ipu: ipu@13080000 {
+		compatible = "ingenic,jz4725b-ipu";
+		reg = <0x13080000 0x64>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <30>;
+
+		clocks = <&cgu JZ4725B_CLK_IPU>;
+		clock-names = "ipu";
+
+		port {
+			ipu_input: endpoint {
+				remote-endpoint = <&ipu_output>;
+			};
+		};
+	};
+
+	bch: ecc-controller@130d0000 {
+		compatible = "ingenic,jz4725b-bch";
+		reg = <0x130d0000 0x44>;
+
+		clocks = <&cgu JZ4725B_CLK_BCH>;
+	};
+
+	rom: memory@1fc00000 {
+		compatible = "mtd-rom";
+		probe-type = "map_rom";
+		reg = <0x1fc00000 0x2000>;
+
+		bank-width = <4>;
+		device-width = <1>;
+	};
+};
diff --git a/arch/mips/boot/dts/ingenic/jz4740.dtsi b/arch/mips/boot/dts/ingenic/jz4740.dtsi
new file mode 100644
index 000000000..7f76cba03
--- /dev/null
+++ b/arch/mips/boot/dts/ingenic/jz4740.dtsi
@@ -0,0 +1,334 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/clock/ingenic,jz4740-cgu.h>
+#include <dt-bindings/clock/ingenic,tcu.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "ingenic,jz4740";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "ingenic,xburst-mxu1.0";
+			reg = <0>;
+
+			clocks = <&cgu JZ4740_CLK_CCLK>;
+			clock-names = "cpu";
+		};
+	};
+
+	cpuintc: interrupt-controller {
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		compatible = "mti,cpu-interrupt-controller";
+	};
+
+	intc: interrupt-controller@10001000 {
+		compatible = "ingenic,jz4740-intc";
+		reg = <0x10001000 0x14>;
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&cpuintc>;
+		interrupts = <2>;
+	};
+
+	ext: ext {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+	};
+
+	rtc: rtc {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+	};
+
+	cgu: jz4740-cgu@10000000 {
+		compatible = "ingenic,jz4740-cgu";
+		reg = <0x10000000 0x100>;
+
+		clocks = <&ext>, <&rtc>;
+		clock-names = "ext", "rtc";
+
+		#clock-cells = <1>;
+	};
+
+	tcu: timer@10002000 {
+		compatible = "ingenic,jz4740-tcu", "simple-mfd";
+		reg = <0x10002000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x10002000 0x1000>;
+
+		#clock-cells = <1>;
+
+		clocks = <&cgu JZ4740_CLK_RTC>,
+			 <&cgu JZ4740_CLK_EXT>,
+			 <&cgu JZ4740_CLK_PCLK>,
+			 <&cgu JZ4740_CLK_TCU>;
+		clock-names = "rtc", "ext", "pclk", "tcu";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <23 22 21>;
+
+		watchdog: watchdog@0 {
+			compatible = "ingenic,jz4740-watchdog";
+			reg = <0x0 0xc>;
+
+			clocks = <&tcu TCU_CLK_WDT>;
+			clock-names = "wdt";
+		};
+
+		pwm: pwm@40 {
+			compatible = "ingenic,jz4740-pwm";
+			reg = <0x40 0x80>;
+
+			#pwm-cells = <3>;
+
+			clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER1>,
+				 <&tcu TCU_CLK_TIMER2>, <&tcu TCU_CLK_TIMER3>,
+				 <&tcu TCU_CLK_TIMER4>, <&tcu TCU_CLK_TIMER5>,
+				 <&tcu TCU_CLK_TIMER6>, <&tcu TCU_CLK_TIMER7>;
+			clock-names = "timer0", "timer1", "timer2", "timer3",
+				      "timer4", "timer5", "timer6", "timer7";
+		};
+	};
+
+	rtc_dev: rtc@10003000 {
+		compatible = "ingenic,jz4740-rtc";
+		reg = <0x10003000 0x40>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <15>;
+
+		clocks = <&cgu JZ4740_CLK_RTC>;
+		clock-names = "rtc";
+	};
+
+	pinctrl: pin-controller@10010000 {
+		compatible = "ingenic,jz4740-pinctrl";
+		reg = <0x10010000 0x400>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpa: gpio@0 {
+			compatible = "ingenic,jz4740-gpio";
+			reg = <0>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 0 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <28>;
+		};
+
+		gpb: gpio@1 {
+			compatible = "ingenic,jz4740-gpio";
+			reg = <1>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 32 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <27>;
+		};
+
+		gpc: gpio@2 {
+			compatible = "ingenic,jz4740-gpio";
+			reg = <2>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 64 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <26>;
+		};
+
+		gpd: gpio@3 {
+			compatible = "ingenic,jz4740-gpio";
+			reg = <3>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 96 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <25>;
+		};
+	};
+
+	aic: audio-controller@10020000 {
+		compatible = "ingenic,jz4740-i2s";
+		reg = <0x10020000 0x38>;
+
+		#sound-dai-cells = <0>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <18>;
+
+		clocks = <&cgu JZ4740_CLK_AIC>,
+			 <&cgu JZ4740_CLK_I2S>,
+			 <&cgu JZ4740_CLK_EXT>,
+			 <&cgu JZ4740_CLK_PLL_HALF>;
+		clock-names = "aic", "i2s", "ext", "pll half";
+
+		dmas = <&dmac 25 0xffffffff>, <&dmac 24 0xffffffff>;
+		dma-names = "rx", "tx";
+	};
+
+	codec: audio-codec@100200a4 {
+		compatible = "ingenic,jz4740-codec";
+		reg = <0x10020080 0x8>;
+
+		#sound-dai-cells = <0>;
+
+		clocks = <&cgu JZ4740_CLK_AIC>;
+		clock-names = "aic";
+	};
+
+	mmc: mmc@10021000 {
+		compatible = "ingenic,jz4740-mmc";
+		reg = <0x10021000 0x1000>;
+
+		clocks = <&cgu JZ4740_CLK_MMC>;
+		clock-names = "mmc";
+
+		interrupt-parent = <&intc>;
+		interrupts = <14>;
+
+		dmas = <&dmac 27 0xffffffff>, <&dmac 26 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		cap-sd-highspeed;
+		cap-mmc-highspeed;
+		cap-sdio-irq;
+	};
+
+	uart0: serial@10030000 {
+		compatible = "ingenic,jz4740-uart";
+		reg = <0x10030000 0x100>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <9>;
+
+		clocks = <&ext>, <&cgu JZ4740_CLK_UART0>;
+		clock-names = "baud", "module";
+	};
+
+	uart1: serial@10031000 {
+		compatible = "ingenic,jz4740-uart";
+		reg = <0x10031000 0x100>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <8>;
+
+		clocks = <&ext>, <&cgu JZ4740_CLK_UART1>;
+		clock-names = "baud", "module";
+	};
+
+	adc: adc@10070000 {
+		compatible = "ingenic,jz4740-adc";
+		reg = <0x10070000 0x30>;
+		#io-channel-cells = <1>;
+
+		clocks = <&cgu JZ4740_CLK_ADC>;
+		clock-names = "adc";
+
+		interrupt-parent = <&intc>;
+		interrupts = <12>;
+	};
+
+	nemc: memory-controller@13010000 {
+		compatible = "ingenic,jz4740-nemc";
+		reg = <0x13010000 0x54>;
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges = <1 0 0x18000000 0x4000000>,
+			 <2 0 0x14000000 0x4000000>,
+			 <3 0 0x0c000000 0x4000000>,
+			 <4 0 0x08000000 0x4000000>;
+
+		clocks = <&cgu JZ4740_CLK_MCLK>;
+	};
+
+	ecc: ecc-controller@13010100 {
+		compatible = "ingenic,jz4740-ecc";
+		reg = <0x13010100 0x2C>;
+
+		clocks = <&cgu JZ4740_CLK_MCLK>;
+	};
+
+	dmac: dma-controller@13020000 {
+		compatible = "ingenic,jz4740-dma";
+		reg = <0x13020000 0xbc>, <0x13020300 0x14>;
+		#dma-cells = <2>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <20>;
+
+		clocks = <&cgu JZ4740_CLK_DMA>;
+	};
+
+	uhc: usb@13030000 {
+		compatible = "ingenic,jz4740-ohci", "generic-ohci";
+		reg = <0x13030000 0x1000>;
+
+		clocks = <&cgu JZ4740_CLK_UHC>;
+		assigned-clocks = <&cgu JZ4740_CLK_UHC>;
+		assigned-clock-rates = <48000000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <3>;
+
+		status = "disabled";
+	};
+
+	udc: usb@13040000 {
+		compatible = "ingenic,jz4740-musb";
+		reg = <0x13040000 0x10000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <24>;
+		interrupt-names = "mc";
+
+		clocks = <&cgu JZ4740_CLK_UDC>;
+		clock-names = "udc";
+	};
+
+	lcd: lcd-controller@13050000 {
+		compatible = "ingenic,jz4740-lcd";
+		reg = <0x13050000 0x60>; /* LCDCMD1+4 */
+
+		interrupt-parent = <&intc>;
+		interrupts = <30>;
+
+		clocks = <&cgu JZ4740_CLK_LCD_PCLK>, <&cgu JZ4740_CLK_LCD>;
+		clock-names = "lcd_pclk", "lcd";
+	};
+};
diff --git a/arch/mips/boot/dts/ingenic/jz4770.dtsi b/arch/mips/boot/dts/ingenic/jz4770.dtsi
new file mode 100644
index 000000000..bda0a3a86
--- /dev/null
+++ b/arch/mips/boot/dts/ingenic/jz4770.dtsi
@@ -0,0 +1,471 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/clock/ingenic,jz4770-cgu.h>
+#include <dt-bindings/clock/ingenic,tcu.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "ingenic,jz4770";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "ingenic,xburst-fpu1.0-mxu1.1";
+			reg = <0>;
+
+			clocks = <&cgu JZ4770_CLK_CCLK>;
+			clock-names = "cpu";
+		};
+	};
+
+	cpuintc: interrupt-controller {
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		compatible = "mti,cpu-interrupt-controller";
+	};
+
+	intc: interrupt-controller@10001000 {
+		compatible = "ingenic,jz4770-intc";
+		reg = <0x10001000 0x40>;
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&cpuintc>;
+		interrupts = <2>;
+	};
+
+	ext: ext {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+	};
+
+	osc32k: osc32k {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+	};
+
+	cgu: jz4770-cgu@10000000 {
+		compatible = "ingenic,jz4770-cgu", "simple-mfd";
+		reg = <0x10000000 0x100>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x10000000 0x100>;
+
+		clocks = <&ext>, <&osc32k>;
+		clock-names = "ext", "osc32k";
+
+		#clock-cells = <1>;
+
+		otg_phy: usb-phy@3c {
+			compatible = "ingenic,jz4770-phy";
+			reg = <0x3c 0x10>;
+
+			clocks = <&cgu JZ4770_CLK_OTG_PHY>;
+
+			#phy-cells = <0>;
+		};
+	};
+
+	tcu: timer@10002000 {
+		compatible = "ingenic,jz4770-tcu", "simple-mfd";
+		reg = <0x10002000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x10002000 0x1000>;
+
+		#clock-cells = <1>;
+
+		clocks = <&cgu JZ4770_CLK_RTC>,
+			 <&cgu JZ4770_CLK_EXT>,
+			 <&cgu JZ4770_CLK_PCLK>;
+		clock-names = "rtc", "ext", "pclk";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <27 26 25>;
+
+		watchdog: watchdog@0 {
+			compatible = "ingenic,jz4770-watchdog",
+				     "ingenic,jz4740-watchdog";
+			reg = <0x0 0xc>;
+
+			clocks = <&tcu TCU_CLK_WDT>;
+			clock-names = "wdt";
+		};
+
+		pwm: pwm@40 {
+			compatible = "ingenic,jz4770-pwm", "ingenic,jz4740-pwm";
+			reg = <0x40 0x80>;
+
+			#pwm-cells = <3>;
+
+			clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER1>,
+				 <&tcu TCU_CLK_TIMER2>, <&tcu TCU_CLK_TIMER3>,
+				 <&tcu TCU_CLK_TIMER4>, <&tcu TCU_CLK_TIMER5>,
+				 <&tcu TCU_CLK_TIMER6>, <&tcu TCU_CLK_TIMER7>;
+			clock-names = "timer0", "timer1", "timer2", "timer3",
+				      "timer4", "timer5", "timer6", "timer7";
+		};
+
+		ost: timer@e0 {
+			compatible = "ingenic,jz4770-ost";
+			reg = <0xe0 0x20>;
+
+			clocks = <&tcu TCU_CLK_OST>;
+			clock-names = "ost";
+
+			interrupts = <15>;
+		};
+	};
+
+	rtc: rtc@10003000 {
+		compatible = "ingenic,jz4770-rtc", "ingenic,jz4760-rtc";
+		reg = <0x10003000 0x40>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <32>;
+	};
+
+	pinctrl: pin-controller@10010000 {
+		compatible = "ingenic,jz4770-pinctrl";
+		reg = <0x10010000 0x600>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpa: gpio@0 {
+			compatible = "ingenic,jz4770-gpio";
+			reg = <0>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 0 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <17>;
+		};
+
+		gpb: gpio@1 {
+			compatible = "ingenic,jz4770-gpio";
+			reg = <1>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 32 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <16>;
+		};
+
+		gpc: gpio@2 {
+			compatible = "ingenic,jz4770-gpio";
+			reg = <2>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 64 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <15>;
+		};
+
+		gpd: gpio@3 {
+			compatible = "ingenic,jz4770-gpio";
+			reg = <3>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 96 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <14>;
+		};
+
+		gpe: gpio@4 {
+			compatible = "ingenic,jz4770-gpio";
+			reg = <4>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 128 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <13>;
+		};
+
+		gpf: gpio@5 {
+			compatible = "ingenic,jz4770-gpio";
+			reg = <5>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 160 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <12>;
+		};
+	};
+
+	aic: audio-controller@10020000 {
+		compatible = "ingenic,jz4770-i2s";
+		reg = <0x10020000 0x94>;
+
+		#sound-dai-cells = <0>;
+
+		clocks = <&cgu JZ4770_CLK_AIC>, <&cgu JZ4770_CLK_I2S>,
+			 <&cgu JZ4770_CLK_EXT>, <&cgu JZ4770_CLK_PLL0>;
+		clock-names = "aic", "i2s", "ext", "pll half";
+
+		interrupt-parent = <&intc>;
+		interrupts = <34>;
+
+		dmas = <&dmac0 25 0xffffffff>, <&dmac0 24 0xffffffff>;
+		dma-names = "rx", "tx";
+	};
+
+	codec: audio-codec@100200a0 {
+		compatible = "ingenic,jz4770-codec";
+		reg = <0x100200a4 0x8>;
+
+		#sound-dai-cells = <0>;
+
+		clocks = <&cgu JZ4770_CLK_AIC>;
+		clock-names = "aic";
+	};
+
+	mmc0: mmc@10021000 {
+		compatible = "ingenic,jz4770-mmc", "ingenic,jz4760-mmc";
+		reg = <0x10021000 0x1000>;
+
+		clocks = <&cgu JZ4770_CLK_MMC0>;
+		clock-names = "mmc";
+
+		interrupt-parent = <&intc>;
+		interrupts = <37>;
+
+		dmas = <&dmac1 27 0xffffffff>, <&dmac1 26 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		cap-sd-highspeed;
+		cap-mmc-highspeed;
+		cap-sdio-irq;
+
+		status = "disabled";
+	};
+
+	mmc1: mmc@10022000 {
+		compatible = "ingenic,jz4770-mmc", "ingenic,jz4760-mmc";
+		reg = <0x10022000 0x1000>;
+
+		clocks = <&cgu JZ4770_CLK_MMC1>;
+		clock-names = "mmc";
+
+		interrupt-parent = <&intc>;
+		interrupts = <36>;
+
+		dmas = <&dmac1 31 0xffffffff>, <&dmac1 30 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		cap-sd-highspeed;
+		cap-mmc-highspeed;
+		cap-sdio-irq;
+
+		status = "disabled";
+	};
+
+	mmc2: mmc@10023000 {
+		compatible = "ingenic,jz4770-mmc", "ingenic,jz4760-mmc";
+		reg = <0x10023000 0x1000>;
+
+		clocks = <&cgu JZ4770_CLK_MMC2>;
+		clock-names = "mmc";
+
+		interrupt-parent = <&intc>;
+		interrupts = <35>;
+
+		dmas = <&dmac1 37 0xffffffff>, <&dmac1 36 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		cap-sd-highspeed;
+		cap-mmc-highspeed;
+		cap-sdio-irq;
+
+		status = "disabled";
+	};
+
+	uart0: serial@10030000 {
+		compatible = "ingenic,jz4770-uart";
+		reg = <0x10030000 0x100>;
+
+		clocks = <&ext>, <&cgu JZ4770_CLK_UART0>;
+		clock-names = "baud", "module";
+
+		interrupt-parent = <&intc>;
+		interrupts = <5>;
+
+		status = "disabled";
+	};
+
+	uart1: serial@10031000 {
+		compatible = "ingenic,jz4770-uart";
+		reg = <0x10031000 0x100>;
+
+		clocks = <&ext>, <&cgu JZ4770_CLK_UART1>;
+		clock-names = "baud", "module";
+
+		interrupt-parent = <&intc>;
+		interrupts = <4>;
+
+		status = "disabled";
+	};
+
+	uart2: serial@10032000 {
+		compatible = "ingenic,jz4770-uart";
+		reg = <0x10032000 0x100>;
+
+		clocks = <&ext>, <&cgu JZ4770_CLK_UART2>;
+		clock-names = "baud", "module";
+
+		interrupt-parent = <&intc>;
+		interrupts = <3>;
+
+		status = "disabled";
+	};
+
+	uart3: serial@10033000 {
+		compatible = "ingenic,jz4770-uart";
+		reg = <0x10033000 0x100>;
+
+		clocks = <&ext>, <&cgu JZ4770_CLK_UART3>;
+		clock-names = "baud", "module";
+
+		interrupt-parent = <&intc>;
+		interrupts = <2>;
+
+		status = "disabled";
+	};
+
+	adc: adc@10070000 {
+		compatible = "ingenic,jz4770-adc";
+		reg = <0x10070000 0x30>;
+
+		#io-channel-cells = <1>;
+
+		clocks = <&cgu JZ4770_CLK_ADC>;
+		clock-names = "adc";
+
+		interrupt-parent = <&intc>;
+		interrupts = <18>;
+	};
+
+	gpu: gpu@13040000 {
+		compatible = "vivante,gc";
+		reg = <0x13040000 0x10000>;
+
+		clocks = <&cgu JZ4770_CLK_GPU>,
+			 <&cgu JZ4770_CLK_GPU>,
+			 <&cgu JZ4770_CLK_GPU>;
+		clock-names = "bus", "core", "shader";
+
+		interrupt-parent = <&intc>;
+		interrupts = <6>;
+	};
+
+	lcd: lcd-controller@13050000 {
+		compatible = "ingenic,jz4770-lcd";
+		reg = <0x13050000 0x130>; /* tbc */
+
+		interrupt-parent = <&intc>;
+		interrupts = <31>;
+
+		clocks = <&cgu JZ4770_CLK_LPCLK_MUX>;
+		clock-names = "lcd_pclk";
+	};
+
+	dmac0: dma-controller@13420000 {
+		compatible = "ingenic,jz4770-dma";
+		reg = <0x13420000 0xC0>, <0x13420300 0x20>;
+
+		#dma-cells = <2>;
+
+		clocks = <&cgu JZ4770_CLK_DMA>;
+		interrupt-parent = <&intc>;
+		interrupts = <24>;
+	};
+
+	dmac1: dma-controller@13420100 {
+		compatible = "ingenic,jz4770-dma";
+		reg = <0x13420100 0xC0>, <0x13420400 0x20>;
+
+		#dma-cells = <2>;
+
+		clocks = <&cgu JZ4770_CLK_DMA>;
+		interrupt-parent = <&intc>;
+		interrupts = <23>;
+	};
+
+	uhc: usb@13430000 {
+		compatible = "generic-ohci";
+		reg = <0x13430000 0x1000>;
+
+		clocks = <&cgu JZ4770_CLK_UHC>, <&cgu JZ4770_CLK_UHC_PHY>;
+		assigned-clocks = <&cgu JZ4770_CLK_UHC>;
+		assigned-clock-rates = <48000000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <20>;
+
+		status = "disabled";
+	};
+
+	usb_otg: usb@13440000 {
+		compatible = "ingenic,jz4770-musb";
+		reg = <0x13440000 0x10000>;
+
+		clocks = <&cgu JZ4770_CLK_OTG>;
+		clock-names = "udc";
+
+		interrupt-parent = <&intc>;
+		interrupts = <21>;
+		interrupt-names = "mc";
+
+		phys = <&otg_phy>;
+
+		usb-role-switch;
+	};
+
+	rom: memory@1fc00000 {
+		compatible = "mtd-rom";
+		probe-type = "map_rom";
+		reg = <0x1fc00000 0x2000>;
+
+		bank-width = <4>;
+		device-width = <1>;
+	};
+};
diff --git a/arch/mips/boot/dts/ingenic/jz4780.dtsi b/arch/mips/boot/dts/ingenic/jz4780.dtsi
new file mode 100644
index 000000000..c182a656d
--- /dev/null
+++ b/arch/mips/boot/dts/ingenic/jz4780.dtsi
@@ -0,0 +1,598 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/clock/ingenic,jz4780-cgu.h>
+#include <dt-bindings/clock/ingenic,tcu.h>
+#include <dt-bindings/dma/jz4780-dma.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "ingenic,jz4780";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "ingenic,xburst-fpu1.0-mxu1.1";
+			reg = <0>;
+
+			clocks = <&cgu JZ4780_CLK_CPU>;
+			clock-names = "cpu";
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "ingenic,xburst-fpu1.0-mxu1.1";
+			reg = <1>;
+
+			clocks = <&cgu JZ4780_CLK_CORE1>;
+			clock-names = "cpu";
+		};
+	};
+
+	cpuintc: interrupt-controller {
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		compatible = "mti,cpu-interrupt-controller";
+	};
+
+	intc: interrupt-controller@10001000 {
+		compatible = "ingenic,jz4780-intc";
+		reg = <0x10001000 0x50>;
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&cpuintc>;
+		interrupts = <2>;
+	};
+
+	ext: ext {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+	};
+
+	rtc: rtc {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+	};
+
+	cgu: jz4780-cgu@10000000 {
+		compatible = "ingenic,jz4780-cgu", "simple-mfd";
+		reg = <0x10000000 0x100>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x10000000 0x100>;
+
+		#clock-cells = <1>;
+
+		clocks = <&ext>, <&rtc>;
+		clock-names = "ext", "rtc";
+
+		otg_phy: usb-phy@3c {
+			compatible = "ingenic,jz4780-phy";
+			reg = <0x3c 0x10>;
+
+			clocks = <&cgu JZ4780_CLK_OTG1>;
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		rng: rng@d8 {
+			compatible = "ingenic,jz4780-rng";
+			reg = <0xd8 0x8>;
+
+			status = "disabled";
+		};
+	};
+
+	tcu: timer@10002000 {
+		compatible = "ingenic,jz4780-tcu",
+			     "ingenic,jz4770-tcu",
+			     "simple-mfd";
+		reg = <0x10002000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x10002000 0x1000>;
+
+		#clock-cells = <1>;
+
+		clocks = <&cgu JZ4780_CLK_RTCLK>,
+			 <&cgu JZ4780_CLK_EXCLK>,
+			 <&cgu JZ4780_CLK_PCLK>;
+		clock-names = "rtc", "ext", "pclk";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <27 26 25>;
+
+		watchdog: watchdog@0 {
+			compatible = "ingenic,jz4780-watchdog";
+			reg = <0x0 0xc>;
+
+			clocks = <&tcu TCU_CLK_WDT>;
+			clock-names = "wdt";
+		};
+
+		pwm: pwm@40 {
+			compatible = "ingenic,jz4780-pwm", "ingenic,jz4740-pwm";
+			reg = <0x40 0x80>;
+
+			#pwm-cells = <3>;
+
+			clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER1>,
+				 <&tcu TCU_CLK_TIMER2>, <&tcu TCU_CLK_TIMER3>,
+				 <&tcu TCU_CLK_TIMER4>, <&tcu TCU_CLK_TIMER5>,
+				 <&tcu TCU_CLK_TIMER6>, <&tcu TCU_CLK_TIMER7>;
+			clock-names = "timer0", "timer1", "timer2", "timer3",
+				      "timer4", "timer5", "timer6", "timer7";
+		};
+
+		ost: timer@e0 {
+			compatible = "ingenic,jz4780-ost", "ingenic,jz4770-ost";
+			reg = <0xe0 0x20>;
+
+			clocks = <&tcu TCU_CLK_OST>;
+			clock-names = "ost";
+
+			interrupts = <15>;
+		};
+	};
+
+	rtc_dev: rtc@10003000 {
+		compatible = "ingenic,jz4780-rtc";
+		reg = <0x10003000 0x4c>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <32>;
+
+		clocks = <&cgu JZ4780_CLK_RTCLK>;
+		clock-names = "rtc";
+	};
+
+	pinctrl: pin-controller@10010000 {
+		compatible = "ingenic,jz4780-pinctrl";
+		reg = <0x10010000 0x600>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpa: gpio@0 {
+			compatible = "ingenic,jz4780-gpio";
+			reg = <0>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 0 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <17>;
+		};
+
+		gpb: gpio@1 {
+			compatible = "ingenic,jz4780-gpio";
+			reg = <1>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 32 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <16>;
+		};
+
+		gpc: gpio@2 {
+			compatible = "ingenic,jz4780-gpio";
+			reg = <2>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 64 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <15>;
+		};
+
+		gpd: gpio@3 {
+			compatible = "ingenic,jz4780-gpio";
+			reg = <3>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 96 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <14>;
+		};
+
+		gpe: gpio@4 {
+			compatible = "ingenic,jz4780-gpio";
+			reg = <4>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 128 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <13>;
+		};
+
+		gpf: gpio@5 {
+			compatible = "ingenic,jz4780-gpio";
+			reg = <5>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 160 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <12>;
+		};
+	};
+
+	spi0: spi@10043000 {
+		compatible = "ingenic,jz4780-spi";
+		reg = <0x10043000 0x1c>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <8>;
+
+		clocks = <&cgu JZ4780_CLK_SSI0>;
+		clock-names = "spi";
+
+		dmas = <&dma JZ4780_DMA_SSI0_RX 0xffffffff>,
+		       <&dma JZ4780_DMA_SSI0_TX 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		status = "disabled";
+	};
+
+	uart0: serial@10030000 {
+		compatible = "ingenic,jz4780-uart";
+		reg = <0x10030000 0x100>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <51>;
+
+		clocks = <&ext>, <&cgu JZ4780_CLK_UART0>;
+		clock-names = "baud", "module";
+
+		status = "disabled";
+	};
+
+	uart1: serial@10031000 {
+		compatible = "ingenic,jz4780-uart";
+		reg = <0x10031000 0x100>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <50>;
+
+		clocks = <&ext>, <&cgu JZ4780_CLK_UART1>;
+		clock-names = "baud", "module";
+
+		status = "disabled";
+	};
+
+	uart2: serial@10032000 {
+		compatible = "ingenic,jz4780-uart";
+		reg = <0x10032000 0x100>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <49>;
+
+		clocks = <&ext>, <&cgu JZ4780_CLK_UART2>;
+		clock-names = "baud", "module";
+
+		status = "disabled";
+	};
+
+	uart3: serial@10033000 {
+		compatible = "ingenic,jz4780-uart";
+		reg = <0x10033000 0x100>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <48>;
+
+		clocks = <&ext>, <&cgu JZ4780_CLK_UART3>;
+		clock-names = "baud", "module";
+
+		status = "disabled";
+	};
+
+	uart4: serial@10034000 {
+		compatible = "ingenic,jz4780-uart";
+		reg = <0x10034000 0x100>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <34>;
+
+		clocks = <&ext>, <&cgu JZ4780_CLK_UART4>;
+		clock-names = "baud", "module";
+
+		status = "disabled";
+	};
+
+	spi1: spi@10044000 {
+		compatible = "ingenic,jz4780-spi";
+		reg = <0x10044000 0x1c>;
+		#address-cells = <1>;
+		#size-sells = <0>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <7>;
+
+		clocks = <&cgu JZ4780_CLK_SSI1>;
+		clock-names = "spi";
+
+		dmas = <&dma JZ4780_DMA_SSI1_RX 0xffffffff>,
+		       <&dma JZ4780_DMA_SSI1_TX 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		status = "disabled";
+	};
+
+	i2c0: i2c@10050000 {
+		compatible = "ingenic,jz4780-i2c", "ingenic,jz4770-i2c";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reg = <0x10050000 0x1000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <60>;
+
+		clocks = <&cgu JZ4780_CLK_SMB0>;
+		clock-frequency = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pins_i2c0_data>;
+
+		status = "disabled";
+	};
+
+	i2c1: i2c@10051000 {
+		compatible = "ingenic,jz4780-i2c", "ingenic,jz4770-i2c";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x10051000 0x1000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <59>;
+
+		clocks = <&cgu JZ4780_CLK_SMB1>;
+		clock-frequency = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pins_i2c1_data>;
+
+		status = "disabled";
+	};
+
+	i2c2: i2c@10052000 {
+		compatible = "ingenic,jz4780-i2c", "ingenic,jz4770-i2c";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x10052000 0x1000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <58>;
+
+		clocks = <&cgu JZ4780_CLK_SMB2>;
+		clock-frequency = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pins_i2c2_data>;
+
+		status = "disabled";
+	};
+
+	i2c3: i2c@10053000 {
+		compatible = "ingenic,jz4780-i2c", "ingenic,jz4770-i2c";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x10053000 0x1000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <57>;
+
+		clocks = <&cgu JZ4780_CLK_SMB3>;
+		clock-frequency = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pins_i2c3_data>;
+
+		status = "disabled";
+	};
+
+	i2c4: i2c@10054000 {
+		compatible = "ingenic,jz4780-i2c", "ingenic,jz4770-i2c";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x10054000 0x1000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <56>;
+
+		clocks = <&cgu JZ4780_CLK_SMB4>;
+		clock-frequency = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pins_i2c4_data>;
+
+		status = "disabled";
+	};
+
+	hdmi: hdmi@10180000 {
+		compatible = "ingenic,jz4780-dw-hdmi";
+		reg = <0x10180000 0x8000>;
+		reg-io-width = <4>;
+
+		clocks = <&cgu JZ4780_CLK_AHB0>, <&cgu JZ4780_CLK_HDMI>;
+		clock-names = "iahb", "isfr";
+
+		interrupt-parent = <&intc>;
+		interrupts = <3>;
+
+		status = "disabled";
+	};
+
+	lcdc0: lcdc0@13050000 {
+		compatible = "ingenic,jz4780-lcd";
+		reg = <0x13050000 0x1800>;
+
+		clocks = <&cgu JZ4780_CLK_TVE>, <&cgu JZ4780_CLK_LCD0PIXCLK>;
+		clock-names = "lcd", "lcd_pclk";
+
+		interrupt-parent = <&intc>;
+		interrupts = <31>;
+
+		status = "disabled";
+	};
+
+	lcdc1: lcdc1@130a0000 {
+		compatible = "ingenic,jz4780-lcd";
+		reg = <0x130a0000 0x1800>;
+
+		clocks = <&cgu JZ4780_CLK_TVE>, <&cgu JZ4780_CLK_LCD1PIXCLK>;
+		clock-names = "lcd", "lcd_pclk";
+
+		interrupt-parent = <&intc>;
+		interrupts = <23>;
+
+		status = "disabled";
+	};
+
+	nemc: nemc@13410000 {
+		compatible = "ingenic,jz4780-nemc", "simple-mfd";
+		reg = <0x13410000 0x10000>;
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges = <0 0 0x13410000 0x10000>,
+			 <1 0 0x1b000000 0x1000000>,
+			 <2 0 0x1a000000 0x1000000>,
+			 <3 0 0x19000000 0x1000000>,
+			 <4 0 0x18000000 0x1000000>,
+			 <5 0 0x17000000 0x1000000>,
+			 <6 0 0x16000000 0x1000000>;
+
+		clocks = <&cgu JZ4780_CLK_NEMC>;
+
+		status = "disabled";
+
+		efuse: efuse@d0 {
+			reg = <0 0xd0 0x30>;
+			compatible = "ingenic,jz4780-efuse";
+
+			clocks = <&cgu JZ4780_CLK_AHB2>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			eth0_addr: eth-mac-addr@22 {
+				reg = <0x22 0x6>;
+			};
+		};
+	};
+
+	dma: dma@13420000 {
+		compatible = "ingenic,jz4780-dma";
+		reg = <0x13420000 0x400>, <0x13421000 0x40>;
+		#dma-cells = <2>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <10>;
+
+		clocks = <&cgu JZ4780_CLK_PDMA>;
+	};
+
+	mmc0: mmc@13450000 {
+		compatible = "ingenic,jz4780-mmc";
+		reg = <0x13450000 0x1000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <37>;
+
+		clocks = <&cgu JZ4780_CLK_MSC0>;
+		clock-names = "mmc";
+
+		cap-sd-highspeed;
+		cap-mmc-highspeed;
+		cap-sdio-irq;
+		dmas = <&dma JZ4780_DMA_MSC0_RX 0xffffffff>,
+		       <&dma JZ4780_DMA_MSC0_TX 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		status = "disabled";
+	};
+
+	mmc1: mmc@13460000 {
+		compatible = "ingenic,jz4780-mmc";
+		reg = <0x13460000 0x1000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <36>;
+
+		clocks = <&cgu JZ4780_CLK_MSC1>;
+		clock-names = "mmc";
+
+		cap-sd-highspeed;
+		cap-mmc-highspeed;
+		cap-sdio-irq;
+		dmas = <&dma JZ4780_DMA_MSC1_RX 0xffffffff>,
+		       <&dma JZ4780_DMA_MSC1_TX 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		status = "disabled";
+	};
+
+	bch: bch@134d0000 {
+		compatible = "ingenic,jz4780-bch";
+		reg = <0x134d0000 0x10000>;
+
+		clocks = <&cgu JZ4780_CLK_BCH>;
+
+		status = "disabled";
+	};
+
+	otg: usb@13500000 {
+		compatible = "ingenic,jz4780-otg";
+		reg = <0x13500000 0x40000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <21>;
+
+		clocks = <&cgu JZ4780_CLK_UHC>;
+		clock-names = "otg";
+
+		phys = <&otg_phy>;
+		phy-names = "usb2-phy";
+
+		g-rx-fifo-size = <768>;
+		g-np-tx-fifo-size = <256>;
+		g-tx-fifo-size = <256 256 256 256 256 256 256 512>;
+
+		status = "disabled";
+	};
+};
diff --git a/arch/mips/boot/dts/ingenic/qi_lb60.dts b/arch/mips/boot/dts/ingenic/qi_lb60.dts
new file mode 100644
index 000000000..ba0218971
--- /dev/null
+++ b/arch/mips/boot/dts/ingenic/qi_lb60.dts
@@ -0,0 +1,363 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "jz4740.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/iio/adc/ingenic,adc.h>
+#include <dt-bindings/clock/ingenic,tcu.h>
+#include <dt-bindings/input/input.h>
+
+#define KEY_QI_QI	KEY_F13
+#define KEY_QI_UPRED	KEY_RIGHTALT
+#define KEY_QI_VOLUP	KEY_VOLUMEUP
+#define KEY_QI_VOLDOWN	KEY_VOLUMEDOWN
+#define KEY_QI_FN	KEY_LEFTCTRL
+
+/ {
+	compatible = "qi,lb60", "ingenic,jz4740";
+	model = "Ben Nanonote";
+
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x2000000>;
+	};
+
+	chosen {
+		stdout-path = &uart0;
+	};
+
+	vcc: regulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc";
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	mmc_power: regulator@1 {
+		compatible = "regulator-fixed";
+		regulator-name = "mmc_vcc";
+		gpio = <&gpd 2 0>;
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	amp_supply: regulator@2 {
+		compatible = "regulator-fixed";
+		regulator-name = "amp_supply";
+		gpio = <&gpd 4 0>;
+		enable-active-high;
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	amp: analog-amplifier {
+		compatible = "simple-audio-amplifier";
+		enable-gpios = <&gpb 29 GPIO_ACTIVE_HIGH>;
+		VCC-supply = <&amp_supply>;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+
+		simple-audio-card,name = "QI LB60";
+		simple-audio-card,format = "i2s";
+
+		simple-audio-card,widgets =
+			"Speaker", "Speaker",
+			"Microphone", "Mic";
+		simple-audio-card,routing =
+			"MIC", "Mic",
+			"Speaker", "OUTL",
+			"Speaker", "OUTR",
+			"INL", "LOUT",
+			"INR", "ROUT";
+
+		simple-audio-card,aux-devs = <&amp>;
+
+		simple-audio-card,bitclock-master = <&dai_codec>;
+		simple-audio-card,frame-master = <&dai_codec>;
+
+		dai_cpu: simple-audio-card,cpu {
+			sound-dai = <&aic>;
+		};
+
+		dai_codec: simple-audio-card,codec {
+			sound-dai = <&codec>;
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		key {
+			label = "Power";
+			wakeup-source;
+			linux,code = <KEY_POWER>;
+			gpios = <&gpd 29 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	keyboard {
+		compatible = "gpio-matrix-keypad";
+
+		col-scan-delay-us = <10>;
+		debounce-delay-ms = <10>;
+		wakeup-source;
+
+		row-gpios = <&gpd 18 0>, <&gpd 19 0>, <&gpd 20 0>, <&gpd 21 0>,
+			    <&gpd 22 0>, <&gpd 23 0>, <&gpd 24 0>, <&gpd 26 0>;
+		col-gpios = <&gpc 10 0>, <&gpc 11 0>, <&gpc 12 0>, <&gpc 13 0>,
+			    <&gpc 14 0>, <&gpc 15 0>, <&gpc 16 0>, <&gpc 17 0>;
+		gpio-activelow;
+
+		linux,keymap =
+			<MATRIX_KEY(0, 0, KEY_F1)>,	/* S2 */
+			<MATRIX_KEY(0, 1, KEY_F2)>,	/* S3 */
+			<MATRIX_KEY(0, 2, KEY_F3)>,	/* S4 */
+			<MATRIX_KEY(0, 3, KEY_F4)>,	/* S5 */
+			<MATRIX_KEY(0, 4, KEY_F5)>,	/* S6 */
+			<MATRIX_KEY(0, 5, KEY_F6)>,	/* S7 */
+			<MATRIX_KEY(0, 6, KEY_F7)>,	/* S8 */
+
+			<MATRIX_KEY(1, 0, KEY_Q)>,	/* S10 */
+			<MATRIX_KEY(1, 1, KEY_W)>,	/* S11 */
+			<MATRIX_KEY(1, 2, KEY_E)>,	/* S12 */
+			<MATRIX_KEY(1, 3, KEY_R)>,	/* S13 */
+			<MATRIX_KEY(1, 4, KEY_T)>,	/* S14 */
+			<MATRIX_KEY(1, 5, KEY_Y)>,	/* S15 */
+			<MATRIX_KEY(1, 6, KEY_U)>,	/* S16 */
+			<MATRIX_KEY(1, 7, KEY_I)>,	/* S17 */
+			<MATRIX_KEY(2, 0, KEY_A)>,	/* S18 */
+			<MATRIX_KEY(2, 1, KEY_S)>,	/* S19 */
+			<MATRIX_KEY(2, 2, KEY_D)>,	/* S20 */
+			<MATRIX_KEY(2, 3, KEY_F)>,	/* S21 */
+			<MATRIX_KEY(2, 4, KEY_G)>,	/* S22 */
+			<MATRIX_KEY(2, 5, KEY_H)>,	/* S23 */
+			<MATRIX_KEY(2, 6, KEY_J)>,	/* S24 */
+			<MATRIX_KEY(2, 7, KEY_K)>,	/* S25 */
+			<MATRIX_KEY(3, 0, KEY_ESC)>,	/* S26 */
+			<MATRIX_KEY(3, 1, KEY_Z)>,	/* S27 */
+			<MATRIX_KEY(3, 2, KEY_X)>,	/* S28 */
+			<MATRIX_KEY(3, 3, KEY_C)>,	/* S29 */
+			<MATRIX_KEY(3, 4, KEY_V)>,	/* S30 */
+			<MATRIX_KEY(3, 5, KEY_B)>,	/* S31 */
+			<MATRIX_KEY(3, 6, KEY_N)>,	/* S32 */
+			<MATRIX_KEY(3, 7, KEY_M)>,	/* S33 */
+			<MATRIX_KEY(4, 0, KEY_TAB)>,	/* S34 */
+			<MATRIX_KEY(4, 1, KEY_CAPSLOCK)>,	/* S35 */
+			<MATRIX_KEY(4, 2, KEY_BACKSLASH)>,	/* S36 */
+			<MATRIX_KEY(4, 3, KEY_APOSTROPHE)>,	/* S37 */
+			<MATRIX_KEY(4, 4, KEY_COMMA)>,	/* S38 */
+			<MATRIX_KEY(4, 5, KEY_DOT)>,	/* S39 */
+			<MATRIX_KEY(4, 6, KEY_SLASH)>,	/* S40 */
+			<MATRIX_KEY(4, 7, KEY_UP)>,	/* S41 */
+			<MATRIX_KEY(5, 0, KEY_O)>,	/* S42 */
+			<MATRIX_KEY(5, 1, KEY_L)>,	/* S43 */
+			<MATRIX_KEY(5, 2, KEY_EQUAL)>,	/* S44 */
+			<MATRIX_KEY(5, 3, KEY_QI_UPRED)>,	/* S45 */
+			<MATRIX_KEY(5, 4, KEY_SPACE)>,	/* S46 */
+			<MATRIX_KEY(5, 5, KEY_QI_QI)>,	/* S47 */
+			<MATRIX_KEY(5, 6, KEY_RIGHTCTRL)>,	/* S48 */
+			<MATRIX_KEY(5, 7, KEY_LEFT)>,	/* S49 */
+			<MATRIX_KEY(6, 0, KEY_F8)>,	/* S50 */
+			<MATRIX_KEY(6, 1, KEY_P)>,	/* S51 */
+			<MATRIX_KEY(6, 2, KEY_BACKSPACE)>,/* S52 */
+			<MATRIX_KEY(6, 3, KEY_ENTER)>,	/* S53 */
+			<MATRIX_KEY(6, 4, KEY_QI_VOLUP)>,	/* S54 */
+			<MATRIX_KEY(6, 5, KEY_QI_VOLDOWN)>,	/* S55 */
+			<MATRIX_KEY(6, 6, KEY_DOWN)>,	/* S56 */
+			<MATRIX_KEY(6, 7, KEY_RIGHT)>,	/* S57 */
+
+			<MATRIX_KEY(7, 0, KEY_LEFTSHIFT)>,	/* S58 */
+			<MATRIX_KEY(7, 1, KEY_LEFTALT)>, /* S59 */
+			<MATRIX_KEY(7, 2, KEY_QI_FN)>;	/* S60 */
+	};
+
+	spi {
+		compatible = "spi-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		sck-gpios = <&gpc 23 GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpc 22 GPIO_ACTIVE_HIGH>;
+		cs-gpios = <&gpc 21 GPIO_ACTIVE_LOW>;
+		num-chipselects = <1>;
+	};
+
+	usb_charger: charger {
+		compatible = "gpio-charger";
+		charger-type = "usb-sdp";
+		gpios = <&gpd 28 GPIO_ACTIVE_LOW>;
+		status-gpios = <&gpc 27 GPIO_ACTIVE_LOW>;
+	};
+
+	simple_battery: battery {
+		compatible = "simple-battery";
+		voltage-min-design-microvolt = <3600000>;
+		voltage-max-design-microvolt = <4200000>;
+	};
+
+	pmu {
+		compatible = "ingenic,jz4740-battery";
+		io-channels = <&adc INGENIC_ADC_BATTERY>;
+		io-channel-names = "battery";
+		power-supplies = <&usb_charger>;
+		monitored-battery = <&simple_battery>;
+	};
+
+	hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc INGENIC_ADC_AUX>;
+	};
+
+	panel: panel {
+		compatible = "giantplus,gpm940b0";
+
+		power-supply = <&vcc>;
+
+		port {
+			panel_input: endpoint {
+				remote-endpoint = <&panel_output>;
+			};
+		};
+	};
+
+	usb_phy: usb-phy {
+		compatible = "usb-nop-xceiv";
+		#phy-cells = <0>;
+
+		vcc-supply = <&vcc>;
+	};
+};
+
+&ext {
+	clock-frequency = <12000000>;
+};
+
+&rtc_dev {
+	system-power-controller;
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_uart0>;
+};
+
+&uart1 {
+	status = "disabled";
+};
+
+&nemc {
+	nandc: nand-controller@1 {
+		compatible = "ingenic,jz4740-nand";
+		reg = <1 0 0x4000000>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ecc-engine = <&ecc>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pins_nemc>;
+
+		rb-gpios = <&gpc 30 GPIO_ACTIVE_HIGH>;
+
+		nand@1 {
+			reg = <1>;
+
+			nand-ecc-step-size = <512>;
+			nand-ecc-strength = <4>;
+			nand-ecc-mode = "hw";
+			nand-is-boot-medium;
+			nand-on-flash-bbt;
+
+			partitions {
+				compatible = "fixed-partitions";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				partition@0 {
+					label = "boot";
+					reg = <0x0 0x400000>;
+				};
+
+				partition@400000 {
+					label = "kernel";
+					reg = <0x400000 0x400000>;
+				};
+
+				partition@800000 {
+					label = "rootfs";
+					reg = <0x800000 0x0>;
+				};
+			};
+		};
+	};
+};
+
+&lcd {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_lcd>;
+
+	port {
+		panel_output: endpoint {
+			remote-endpoint = <&panel_input>;
+		};
+	};
+};
+
+&udc {
+	phys = <&usb_phy>;
+};
+
+&pinctrl {
+	pins_lcd: lcd {
+		function = "lcd";
+		groups = "lcd-8bit";
+	};
+
+	pins_nemc: nemc {
+		function = "nand";
+		groups = "nand-fre-fwe", "nand-cs1";
+	};
+
+	pins_uart0: uart0 {
+		function = "uart0";
+		groups = "uart0-data";
+		bias-disable;
+	};
+
+	pins_mmc: mmc {
+		mmc {
+			function = "mmc";
+			groups = "mmc-1bit", "mmc-4bit";
+			bias-disable;
+		};
+
+		mmc-gpios {
+			pins = "PD0", "PD2";
+			bias-disable;
+		};
+	};
+};
+
+&mmc {
+	bus-width = <4>;
+	max-frequency = <24000000>;
+	cd-gpios = <&gpd 0 GPIO_ACTIVE_HIGH>;
+	vmmc-supply = <&mmc_power>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_mmc>;
+};
+
+&tcu {
+	/* 750 kHz for the system timer and clocksource */
+	assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER1>;
+	assigned-clock-rates = <750000>, <750000>;
+};
diff --git a/arch/mips/boot/dts/ingenic/rs90.dts b/arch/mips/boot/dts/ingenic/rs90.dts
new file mode 100644
index 000000000..e8df70dd4
--- /dev/null
+++ b/arch/mips/boot/dts/ingenic/rs90.dts
@@ -0,0 +1,327 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "jz4725b.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/iio/adc/ingenic,adc.h>
+#include <dt-bindings/input/linux-event-codes.h>
+
+/ {
+	compatible = "ylm,rs90", "ingenic,jz4725b";
+	model = "RS-90";
+
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x2000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		vmem: video-memory@1f00000 {
+			compatible = "shared-dma-pool";
+			reg = <0x1f00000 0x100000>;
+			reusable;
+		};
+	};
+
+	vcc: regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vcc";
+		regulaor-min-microvolt = <3300000>;
+		regulaor-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 3 40000 0>;
+
+		brightness-levels = <0 16 32 48 64 80 112 144 192 255>;
+		default-brightness-level = <8>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pins_pwm3>;
+
+		power-supply = <&vcc>;
+	};
+
+	keys@0 {
+		compatible = "gpio-keys";
+
+		key-0 {
+			label = "D-pad up";
+			linux,code = <KEY_UP>;
+			gpios = <&gpc 10 GPIO_ACTIVE_LOW>;
+		};
+
+		key-1 {
+			label = "D-pad down";
+			linux,code = <KEY_DOWN>;
+			gpios = <&gpc 11 GPIO_ACTIVE_LOW>;
+		};
+
+		key-2 {
+			label = "D-pad left";
+			linux,code = <KEY_LEFT>;
+			gpios = <&gpb 31 GPIO_ACTIVE_LOW>;
+		};
+
+		key-3 {
+			label = "D-pad right";
+			linux,code = <KEY_RIGHT>;
+			gpios = <&gpd 21 GPIO_ACTIVE_LOW>;
+		};
+
+		key-4 {
+			label = "Button A";
+			linux,code = <KEY_LEFTCTRL>;
+			gpios = <&gpc 31 GPIO_ACTIVE_LOW>;
+		};
+
+		key-5 {
+			label = "Button B";
+			linux,code = <KEY_LEFTALT>;
+			gpios = <&gpc 30 GPIO_ACTIVE_LOW>;
+		};
+
+		key-6 {
+			label = "Right shoulder button";
+			linux,code = <KEY_BACKSPACE>;
+			gpios = <&gpc 12 GPIO_ACTIVE_LOW>;
+			debounce-interval = <10>;
+		};
+
+		key-7 {
+			label = "Start button";
+			linux,code = <KEY_ENTER>;
+			gpios = <&gpd 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	keys@1 {
+		compatible = "adc-keys";
+		io-channels = <&adc INGENIC_ADC_AUX>;
+		io-channel-names = "buttons";
+		keyup-threshold-microvolt = <1400000>;
+		poll-interval = <30>;
+
+		key@0 {
+			label = "Left shoulder button";
+			linux,code = <KEY_TAB>;
+			press-threshold-microvolt = <800000>;
+		};
+
+		key@1 {
+			label = "Select button";
+			linux,code = <KEY_ESC>;
+			press-threshold-microvolt = <1100000>;
+		};
+	};
+
+	amp: analog-amplifier {
+		compatible = "simple-audio-amplifier";
+		enable-gpios = <&gpc 15 GPIO_ACTIVE_HIGH>;
+
+		VCC-supply = <&vcc>;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+
+		simple-audio-card,name = "rs90-audio";
+		simple-audio-card,format = "i2s";
+
+		simple-audio-card,widgets =
+			"Speaker", "Speaker",
+			"Headphone", "Headphones";
+		simple-audio-card,routing =
+			"INL", "LHPOUT",
+			"INR", "RHPOUT",
+			"Headphones", "LHPOUT",
+			"Headphones", "RHPOUT",
+			"Speaker", "OUTL",
+			"Speaker", "OUTR";
+		simple-audio-card,pin-switches = "Speaker";
+
+		simple-audio-card,hp-det-gpio = <&gpd 16 GPIO_ACTIVE_LOW>;
+		simple-audio-card,aux-devs = <&amp>;
+
+		simple-audio-card,bitclock-master = <&dai_codec>;
+		simple-audio-card,frame-master = <&dai_codec>;
+
+		dai_cpu: simple-audio-card,cpu {
+			sound-dai = <&aic>;
+		};
+
+		dai_codec: simple-audio-card,codec {
+			sound-dai = <&codec>;
+		};
+
+	};
+
+	usb_phy: usb-phy {
+		compatible = "usb-nop-xceiv";
+		#phy-cells = <0>;
+
+		clocks = <&cgu JZ4725B_CLK_UDC_PHY>;
+		clock-names = "main_clk";
+		vcc-supply = <&vcc>;
+	};
+
+	panel {
+		compatible = "sharp,ls020b1dd01d";
+
+		backlight = <&backlight>;
+		power-supply = <&vcc>;
+
+		port {
+			panel_input: endpoint {
+				remote-endpoint = <&panel_output>;
+			};
+		};
+	};
+};
+
+&ext {
+	clock-frequency = <12000000>;
+};
+
+&rtc_dev {
+	system-power-controller;
+};
+
+&udc {
+	phys = <&usb_phy>;
+};
+
+&pinctrl {
+	pins_mmc1: mmc1 {
+		function = "mmc1";
+		groups = "mmc1-1bit";
+	};
+
+	pins_nemc: nemc {
+		function = "nand";
+		groups = "nand-cs1", "nand-cle-ale", "nand-fre-fwe";
+	};
+
+	pins_pwm3: pwm3 {
+		function = "pwm3";
+		groups = "pwm3";
+		bias-disable;
+	};
+
+	pins_lcd: lcd {
+		function = "lcd";
+		groups = "lcd-8bit", "lcd-16bit", "lcd-special";
+	};
+};
+
+&mmc0 {
+	status = "disabled";
+};
+
+&mmc1 {
+	bus-width = <1>;
+	max-frequency = <48000000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_mmc1>;
+
+	cd-gpios = <&gpc 20 GPIO_ACTIVE_LOW>;
+};
+
+&uart {
+	/*
+	 * The pins for RX/TX are used for the right shoulder button and
+	 * backlight PWM.
+	 */
+	status = "disabled";
+};
+
+&nemc {
+	nandc: nand-controller@1 {
+		compatible = "ingenic,jz4725b-nand";
+		reg = <1 0 0x4000000>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ecc-engine = <&bch>;
+
+		ingenic,nemc-tAS = <10>;
+		ingenic,nemc-tAH = <5>;
+		ingenic,nemc-tBP = <10>;
+		ingenic,nemc-tAW = <15>;
+		ingenic,nemc-tSTRV = <100>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pins_nemc>;
+
+		rb-gpios = <&gpc 27 GPIO_ACTIVE_HIGH>;
+
+		nand@1 {
+			reg = <1>;
+
+			nand-ecc-step-size = <512>;
+			nand-ecc-strength = <8>;
+			nand-ecc-mode = "hw";
+			nand-is-boot-medium;
+			nand-on-flash-bbt;
+
+			partitions {
+				compatible = "fixed-partitions";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				partition@0 {
+					label = "bootloader";
+					reg = <0x0 0x20000>;
+				};
+
+				partition@20000 {
+					label = "system";
+					reg = <0x20000 0x0>;
+				};
+			};
+		};
+	};
+};
+
+&cgu {
+	/* Use 32kHz oscillator as the parent of the RTC clock */
+	assigned-clocks = <&cgu JZ4725B_CLK_RTC>;
+	assigned-clock-parents = <&cgu JZ4725B_CLK_OSC32K>;
+};
+
+&tcu {
+	/*
+	 * 750 kHz for the system timer and clocksource, and use RTC as the
+	 * parent for the watchdog clock.
+	 */
+	assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER1>, <&tcu TCU_CLK_WDT>;
+	assigned-clock-parents = <0>, <0>, <&cgu JZ4725B_CLK_RTC>;
+	assigned-clock-rates = <750000>, <750000>;
+};
+
+&lcd {
+	memory-region = <&vmem>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_lcd>;
+};
+
+&lcd_ports {
+	port@0 {
+		reg = <0>;
+
+		panel_output: endpoint {
+			remote-endpoint = <&panel_input>;
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/ingenic/x1000.dtsi b/arch/mips/boot/dts/ingenic/x1000.dtsi
new file mode 100644
index 000000000..42e69664e
--- /dev/null
+++ b/arch/mips/boot/dts/ingenic/x1000.dtsi
@@ -0,0 +1,420 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/clock/ingenic,tcu.h>
+#include <dt-bindings/clock/ingenic,x1000-cgu.h>
+#include <dt-bindings/dma/x1000-dma.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "ingenic,x1000", "ingenic,x1000e";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "ingenic,xburst-fpu1.0-mxu1.1";
+			reg = <0>;
+
+			clocks = <&cgu X1000_CLK_CPU>;
+			clock-names = "cpu";
+		};
+	};
+
+	cpuintc: interrupt-controller {
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		compatible = "mti,cpu-interrupt-controller";
+	};
+
+	intc: interrupt-controller@10001000 {
+		compatible = "ingenic,x1000-intc", "ingenic,jz4780-intc";
+		reg = <0x10001000 0x50>;
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&cpuintc>;
+		interrupts = <2>;
+	};
+
+	exclk: ext {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+	};
+
+	rtclk: rtc {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+	};
+
+	cgu: x1000-cgu@10000000 {
+		compatible = "ingenic,x1000-cgu", "simple-mfd";
+		reg = <0x10000000 0x100>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x10000000 0x100>;
+
+		#clock-cells = <1>;
+
+		clocks = <&exclk>, <&rtclk>;
+		clock-names = "ext", "rtc";
+
+		otg_phy: usb-phy@3c {
+			compatible = "ingenic,x1000-phy";
+			reg = <0x3c 0x10>;
+
+			clocks = <&cgu X1000_CLK_OTGPHY>;
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		rng: rng@d8 {
+			compatible = "ingenic,x1000-rng";
+			reg = <0xd8 0x8>;
+
+			status = "disabled";
+		};
+
+		mac_phy_ctrl: mac-phy-ctrl@e8 {
+			compatible = "syscon";
+			reg = <0xe8 0x4>;
+		};
+	};
+
+	ost: timer@12000000 {
+		compatible = "ingenic,x1000-ost";
+		reg = <0x12000000 0x3c>;
+
+		#clock-cells = <1>;
+
+		clocks = <&cgu X1000_CLK_OST>;
+		clock-names = "ost";
+
+		interrupt-parent = <&cpuintc>;
+		interrupts = <3>;
+	};
+
+	tcu: timer@10002000 {
+		compatible = "ingenic,x1000-tcu", "simple-mfd";
+		reg = <0x10002000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x10002000 0x1000>;
+
+		#clock-cells = <1>;
+
+		clocks = <&cgu X1000_CLK_RTCLK>,
+			 <&cgu X1000_CLK_EXCLK>,
+			 <&cgu X1000_CLK_PCLK>,
+			 <&cgu X1000_CLK_TCU>;
+		clock-names = "rtc", "ext", "pclk", "tcu";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <27 26 25>;
+
+		wdt: watchdog@0 {
+			compatible = "ingenic,x1000-watchdog", "ingenic,jz4780-watchdog";
+			reg = <0x0 0x10>;
+
+			clocks = <&tcu TCU_CLK_WDT>;
+			clock-names = "wdt";
+		};
+
+		pwm: pwm@40 {
+			compatible = "ingenic,x1000-pwm";
+			reg = <0x40 0x50>;
+
+			#pwm-cells = <3>;
+
+			clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER1>,
+				 <&tcu TCU_CLK_TIMER2>, <&tcu TCU_CLK_TIMER3>,
+				 <&tcu TCU_CLK_TIMER4>;
+			clock-names = "timer0", "timer1", "timer2", "timer3", "timer4";
+		};
+	};
+
+	rtc: rtc@10003000 {
+		compatible = "ingenic,x1000-rtc", "ingenic,jz4780-rtc";
+		reg = <0x10003000 0x4c>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <32>;
+
+		clocks = <&cgu X1000_CLK_RTCLK>;
+		clock-names = "rtc";
+	};
+
+	pinctrl: pin-controller@10010000 {
+		compatible = "ingenic,x1000-pinctrl";
+		reg = <0x10010000 0x800>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpa: gpio@0 {
+			compatible = "ingenic,x1000-gpio";
+			reg = <0>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 0 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <17>;
+		};
+
+		gpb: gpio@1 {
+			compatible = "ingenic,x1000-gpio";
+			reg = <1>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 32 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <16>;
+		};
+
+		gpc: gpio@2 {
+			compatible = "ingenic,x1000-gpio";
+			reg = <2>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 64 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <15>;
+		};
+
+		gpd: gpio@3 {
+			compatible = "ingenic,x1000-gpio";
+			reg = <3>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 96 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <14>;
+		};
+	};
+
+	uart0: serial@10030000 {
+		compatible = "ingenic,x1000-uart";
+		reg = <0x10030000 0x100>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <51>;
+
+		clocks = <&exclk>, <&cgu X1000_CLK_UART0>;
+		clock-names = "baud", "module";
+
+		status = "disabled";
+	};
+
+	uart1: serial@10031000 {
+		compatible = "ingenic,x1000-uart";
+		reg = <0x10031000 0x100>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <50>;
+
+		clocks = <&exclk>, <&cgu X1000_CLK_UART1>;
+		clock-names = "baud", "module";
+
+		status = "disabled";
+	};
+
+	uart2: serial@10032000 {
+		compatible = "ingenic,x1000-uart";
+		reg = <0x10032000 0x100>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <49>;
+
+		clocks = <&exclk>, <&cgu X1000_CLK_UART2>;
+		clock-names = "baud", "module";
+
+		status = "disabled";
+	};
+
+	ssi: spi@10043000 {
+		compatible = "ingenic,x1000-spi";
+		reg = <0x10043000 0x20>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <8>;
+
+		clocks = <&cgu X1000_CLK_SSI>;
+		clock-names = "spi";
+
+		dmas = <&pdma X1000_DMA_SSI0_RX 0xffffffff>,
+			   <&pdma X1000_DMA_SSI0_TX 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		status = "disabled";
+	};
+
+	i2c0: i2c-controller@10050000 {
+		compatible = "ingenic,x1000-i2c";
+		reg = <0x10050000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <60>;
+
+		clocks = <&cgu X1000_CLK_I2C0>;
+
+		status = "disabled";
+	};
+
+	i2c1: i2c-controller@10051000 {
+		compatible = "ingenic,x1000-i2c";
+		reg = <0x10051000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <59>;
+
+		clocks = <&cgu X1000_CLK_I2C1>;
+
+		status = "disabled";
+	};
+
+	i2c2: i2c-controller@10052000 {
+		compatible = "ingenic,x1000-i2c";
+		reg = <0x10052000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <58>;
+
+		clocks = <&cgu X1000_CLK_I2C2>;
+
+		status = "disabled";
+	};
+
+	pdma: dma-controller@13420000 {
+		compatible = "ingenic,x1000-dma";
+		reg = <0x13420000 0x400>, <0x13421000 0x40>;
+
+		#dma-cells = <2>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <10>;
+
+		clocks = <&cgu X1000_CLK_PDMA>;
+	};
+
+	msc0: mmc@13450000 {
+		compatible = "ingenic,x1000-mmc";
+		reg = <0x13450000 0x1000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <37>;
+
+		clocks = <&cgu X1000_CLK_MSC0>;
+		clock-names = "mmc";
+
+		cap-sd-highspeed;
+		cap-mmc-highspeed;
+		cap-sdio-irq;
+
+		dmas = <&pdma X1000_DMA_MSC0_RX 0xffffffff>,
+			   <&pdma X1000_DMA_MSC0_TX 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		status = "disabled";
+	};
+
+	msc1: mmc@13460000 {
+		compatible = "ingenic,x1000-mmc";
+		reg = <0x13460000 0x1000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <36>;
+
+		clocks = <&cgu X1000_CLK_MSC1>;
+		clock-names = "mmc";
+
+		cap-sd-highspeed;
+		cap-mmc-highspeed;
+		cap-sdio-irq;
+
+		dmas = <&pdma X1000_DMA_MSC1_RX 0xffffffff>,
+			   <&pdma X1000_DMA_MSC1_TX 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		status = "disabled";
+	};
+
+	mac: ethernet@134b0000 {
+		compatible = "ingenic,x1000-mac", "snps,dwmac";
+		reg = <0x134b0000 0x2000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <55>;
+		interrupt-names = "macirq";
+
+		clocks = <&cgu X1000_CLK_MAC>;
+		clock-names = "stmmaceth";
+
+		mode-reg = <&mac_phy_ctrl>;
+
+		status = "disabled";
+
+		mdio: mdio {
+			compatible = "snps,dwmac-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+	};
+
+	otg: usb@13500000 {
+		compatible = "ingenic,x1000-otg";
+		reg = <0x13500000 0x40000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <21>;
+
+		clocks = <&cgu X1000_CLK_OTG>;
+		clock-names = "otg";
+
+		phys = <&otg_phy>;
+		phy-names = "usb2-phy";
+
+		g-rx-fifo-size = <768>;
+		g-np-tx-fifo-size = <256>;
+		g-tx-fifo-size = <256 256 256 256 256 256 256 512>;
+
+		status = "disabled";
+	};
+};
diff --git a/arch/mips/boot/dts/ingenic/x1830.dtsi b/arch/mips/boot/dts/ingenic/x1830.dtsi
new file mode 100644
index 000000000..65a5da71c
--- /dev/null
+++ b/arch/mips/boot/dts/ingenic/x1830.dtsi
@@ -0,0 +1,430 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/clock/ingenic,tcu.h>
+#include <dt-bindings/clock/ingenic,x1830-cgu.h>
+#include <dt-bindings/dma/x1830-dma.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "ingenic,x1830";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "ingenic,xburst-fpu2.0-mxu2.0";
+			reg = <0>;
+
+			clocks = <&cgu X1830_CLK_CPU>;
+			clock-names = "cpu";
+		};
+	};
+
+	cpuintc: interrupt-controller {
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		compatible = "mti,cpu-interrupt-controller";
+	};
+
+	intc: interrupt-controller@10001000 {
+		compatible = "ingenic,x1830-intc", "ingenic,jz4780-intc";
+		reg = <0x10001000 0x50>;
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&cpuintc>;
+		interrupts = <2>;
+	};
+
+	exclk: ext {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+	};
+
+	rtclk: rtc {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+	};
+
+	cgu: x1830-cgu@10000000 {
+		compatible = "ingenic,x1830-cgu", "simple-mfd";
+		reg = <0x10000000 0x100>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x10000000 0x100>;
+
+		#clock-cells = <1>;
+
+		clocks = <&exclk>, <&rtclk>;
+		clock-names = "ext", "rtc";
+
+		otg_phy: usb-phy@3c {
+			compatible = "ingenic,x1830-phy";
+			reg = <0x3c 0x10>;
+
+			clocks = <&cgu X1830_CLK_OTGPHY>;
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		mac_phy_ctrl: mac-phy-ctrl@e8 {
+			compatible = "syscon";
+			reg = <0xe8 0x4>;
+		};
+	};
+
+	ost: timer@12000000 {
+		compatible = "ingenic,x1830-ost", "ingenic,x1000-ost";
+		reg = <0x12000000 0x3c>;
+
+		#clock-cells = <1>;
+
+		clocks = <&cgu X1830_CLK_OST>;
+		clock-names = "ost";
+
+		interrupt-parent = <&cpuintc>;
+		interrupts = <4>;
+	};
+
+	tcu: timer@10002000 {
+		compatible = "ingenic,x1830-tcu", "ingenic,x1000-tcu", "simple-mfd";
+		reg = <0x10002000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x10002000 0x1000>;
+
+		#clock-cells = <1>;
+
+		clocks = <&cgu X1830_CLK_RTCLK>,
+			 <&cgu X1830_CLK_EXCLK>,
+			 <&cgu X1830_CLK_PCLK>,
+			 <&cgu X1830_CLK_TCU>;
+		clock-names = "rtc", "ext", "pclk", "tcu";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <27 26 25>;
+
+		wdt: watchdog@0 {
+			compatible = "ingenic,x1830-watchdog", "ingenic,jz4780-watchdog";
+			reg = <0x0 0x10>;
+
+			clocks = <&tcu TCU_CLK_WDT>;
+			clock-names = "wdt";
+		};
+
+		pwm: pwm@40 {
+			compatible = "ingenic,x1830-pwm", "ingenic,jz4740-pwm";
+			reg = <0x40 0x80>;
+
+			#pwm-cells = <3>;
+
+			clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER1>,
+				 <&tcu TCU_CLK_TIMER2>, <&tcu TCU_CLK_TIMER3>,
+				 <&tcu TCU_CLK_TIMER4>, <&tcu TCU_CLK_TIMER5>,
+				 <&tcu TCU_CLK_TIMER6>, <&tcu TCU_CLK_TIMER7>;
+			clock-names = "timer0", "timer1", "timer2", "timer3",
+				      "timer4", "timer5", "timer6", "timer7";
+		};
+	};
+
+	rtc: rtc@10003000 {
+		compatible = "ingenic,x1830-rtc", "ingenic,jz4780-rtc";
+		reg = <0x10003000 0x4c>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <32>;
+
+		clocks = <&cgu X1830_CLK_RTCLK>;
+		clock-names = "rtc";
+	};
+
+	pinctrl: pin-controller@10010000 {
+		compatible = "ingenic,x1830-pinctrl";
+		reg = <0x10010000 0x800>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpa: gpio@0 {
+			compatible = "ingenic,x1830-gpio";
+			reg = <0>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 0 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <17>;
+		};
+
+		gpb: gpio@1 {
+			compatible = "ingenic,x1830-gpio";
+			reg = <1>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 32 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <16>;
+		};
+
+		gpc: gpio@2 {
+			compatible = "ingenic,x1830-gpio";
+			reg = <2>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 64 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <15>;
+		};
+
+		gpd: gpio@3 {
+			compatible = "ingenic,x1830-gpio";
+			reg = <3>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 96 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <14>;
+		};
+	};
+
+	uart0: serial@10030000 {
+		compatible = "ingenic,x1830-uart", "ingenic,x1000-uart";
+		reg = <0x10030000 0x100>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <51>;
+
+		clocks = <&exclk>, <&cgu X1830_CLK_UART0>;
+		clock-names = "baud", "module";
+
+		status = "disabled";
+	};
+
+	uart1: serial@10031000 {
+		compatible = "ingenic,x1830-uart", "ingenic,x1000-uart";
+		reg = <0x10031000 0x100>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <50>;
+
+		clocks = <&exclk>, <&cgu X1830_CLK_UART1>;
+		clock-names = "baud", "module";
+
+		status = "disabled";
+	};
+
+	ssi0: spi@10043000 {
+		compatible = "ingenic,x1830-spi", "ingenic,x1000-spi";
+		reg = <0x10043000 0x20>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <9>;
+
+		clocks = <&cgu X1830_CLK_SSI0>;
+		clock-names = "spi";
+
+		dmas = <&pdma X1830_DMA_SSI0_RX 0xffffffff>,
+			   <&pdma X1830_DMA_SSI0_TX 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		status = "disabled";
+	};
+
+	ssi1: spi@10044000 {
+		compatible = "ingenic,x1830-spi", "ingenic,x1000-spi";
+		reg = <0x10044000 0x20>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <8>;
+
+		clocks = <&cgu X1830_CLK_SSI1>;
+		clock-names = "spi";
+
+		dmas = <&pdma X1830_DMA_SSI1_RX 0xffffffff>,
+			   <&pdma X1830_DMA_SSI1_TX 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		status = "disabled";
+	};
+
+	i2c0: i2c-controller@10050000 {
+		compatible = "ingenic,x1830-i2c", "ingenic,x1000-i2c";
+		reg = <0x10050000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <60>;
+
+		clocks = <&cgu X1830_CLK_SMB0>;
+
+		status = "disabled";
+	};
+
+	i2c1: i2c-controller@10051000 {
+		compatible = "ingenic,x1830-i2c", "ingenic,x1000-i2c";
+		reg = <0x10051000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <59>;
+
+		clocks = <&cgu X1830_CLK_SMB1>;
+
+		status = "disabled";
+	};
+
+	i2c2: i2c-controller@10052000 {
+		compatible = "ingenic,x1830-i2c", "ingenic,x1000-i2c";
+		reg = <0x10052000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <58>;
+
+		clocks = <&cgu X1830_CLK_SMB2>;
+
+		status = "disabled";
+	};
+
+	dtrng: trng@10072000 {
+		compatible = "ingenic,x1830-dtrng";
+		reg = <0x10072000 0xc>;
+
+		clocks = <&cgu X1830_CLK_DTRNG>;
+
+		status = "disabled";
+	};
+
+	pdma: dma-controller@13420000 {
+		compatible = "ingenic,x1830-dma";
+		reg = <0x13420000 0x400>, <0x13421000 0x40>;
+
+		#dma-cells = <2>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <10>;
+
+		clocks = <&cgu X1830_CLK_PDMA>;
+	};
+
+	msc0: mmc@13450000 {
+		compatible = "ingenic,x1830-mmc", "ingenic,x1000-mmc";
+		reg = <0x13450000 0x1000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <37>;
+
+		clocks = <&cgu X1830_CLK_MSC0>;
+		clock-names = "mmc";
+
+		cap-sd-highspeed;
+		cap-mmc-highspeed;
+		cap-sdio-irq;
+
+		dmas = <&pdma X1830_DMA_MSC0_RX 0xffffffff>,
+			   <&pdma X1830_DMA_MSC0_TX 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		status = "disabled";
+	};
+
+	msc1: mmc@13460000 {
+		compatible = "ingenic,x1830-mmc", "ingenic,x1000-mmc";
+		reg = <0x13460000 0x1000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <36>;
+
+		clocks = <&cgu X1830_CLK_MSC1>;
+		clock-names = "mmc";
+
+		cap-sd-highspeed;
+		cap-mmc-highspeed;
+		cap-sdio-irq;
+
+		dmas = <&pdma X1830_DMA_MSC1_RX 0xffffffff>,
+			   <&pdma X1830_DMA_MSC1_TX 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		status = "disabled";
+	};
+
+	mac: ethernet@134b0000 {
+		compatible = "ingenic,x1830-mac", "snps,dwmac";
+		reg = <0x134b0000 0x2000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <55>;
+		interrupt-names = "macirq";
+
+		clocks = <&cgu X1830_CLK_MAC>;
+		clock-names = "stmmaceth";
+
+		mode-reg = <&mac_phy_ctrl>;
+
+		status = "disabled";
+
+		mdio: mdio {
+			compatible = "snps,dwmac-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+	};
+
+	otg: usb@13500000 {
+		compatible = "ingenic,x1830-otg";
+		reg = <0x13500000 0x40000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <21>;
+
+		clocks = <&cgu X1830_CLK_OTG>;
+		clock-names = "otg";
+
+		phys = <&otg_phy>;
+		phy-names = "usb2-phy";
+
+		g-rx-fifo-size = <768>;
+		g-np-tx-fifo-size = <256>;
+		g-tx-fifo-size = <256 256 256 256 256 256 256 512>;
+
+		status = "disabled";
+	};
+};
diff --git a/arch/mips/boot/dts/lantiq/Makefile b/arch/mips/boot/dts/lantiq/Makefile
new file mode 100644
index 000000000..ae6e3e21e
--- /dev/null
+++ b/arch/mips/boot/dts/lantiq/Makefile
@@ -0,0 +1,4 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_DT_EASY50712)	+= danube_easy50712.dtb
+
+obj-$(CONFIG_BUILTIN_DTB)	+= $(addsuffix .o, $(dtb-y))
diff --git a/arch/mips/boot/dts/lantiq/danube.dtsi b/arch/mips/boot/dts/lantiq/danube.dtsi
new file mode 100644
index 000000000..510be63c8
--- /dev/null
+++ b/arch/mips/boot/dts/lantiq/danube.dtsi
@@ -0,0 +1,106 @@
+// SPDX-License-Identifier: GPL-2.0
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "lantiq,xway", "lantiq,danube";
+
+	cpus {
+		cpu@0 {
+			compatible = "mips,mips24Kc";
+		};
+	};
+
+	biu@1f800000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "lantiq,biu", "simple-bus";
+		reg = <0x1f800000 0x800000>;
+		ranges = <0x0 0x1f800000 0x7fffff>;
+
+		icu0: icu@80200 {
+			#interrupt-cells = <1>;
+			interrupt-controller;
+			compatible = "lantiq,icu";
+			reg = <0x80200 0x120>;
+		};
+
+		watchdog@803f0 {
+			compatible = "lantiq,wdt";
+			reg = <0x803f0 0x10>;
+		};
+	};
+
+	sram@1f000000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "lantiq,sram";
+		reg = <0x1f000000 0x800000>;
+		ranges = <0x0 0x1f000000 0x7fffff>;
+
+		eiu0: eiu@101000 {
+			#interrupt-cells = <1>;
+			interrupt-controller;
+			interrupt-parent;
+			compatible = "lantiq,eiu-xway";
+			reg = <0x101000 0x1000>;
+		};
+
+		pmu0: pmu@102000 {
+			compatible = "lantiq,pmu-xway";
+			reg = <0x102000 0x1000>;
+		};
+
+		cgu0: cgu@103000 {
+			compatible = "lantiq,cgu-xway";
+			reg = <0x103000 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		rcu0: rcu@203000 {
+			compatible = "lantiq,rcu-xway";
+			reg = <0x203000 0x1000>;
+		};
+	};
+
+	fpi@10000000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "lantiq,fpi", "simple-bus";
+		ranges = <0x0 0x10000000 0xeefffff>;
+		reg = <0x10000000 0xef00000>;
+
+		gptu@e100a00 {
+			compatible = "lantiq,gptu-xway";
+			reg = <0xe100a00 0x100>;
+		};
+
+		serial@e100c00 {
+			compatible = "lantiq,asc";
+			reg = <0xe100c00 0x400>;
+			interrupt-parent = <&icu0>;
+			interrupts = <112 113 114>;
+		};
+
+		dma0: dma@e104100 {
+			compatible = "lantiq,dma-xway";
+			reg = <0xe104100 0x800>;
+		};
+
+		ebu0: ebu@e105300 {
+			compatible = "lantiq,ebu-xway";
+			reg = <0xe105300 0x100>;
+		};
+
+		pci0: pci@e105400 {
+			#address-cells = <3>;
+			#size-cells = <2>;
+			#interrupt-cells = <1>;
+			compatible = "lantiq,pci-xway";
+			bus-range = <0x0 0x0>;
+			ranges = <0x2000000 0 0x8000000 0x8000000 0 0x2000000	/* pci memory */
+				  0x1000000 0 0x00000000 0xae00000 0 0x200000>; /* io space */
+			reg = <0x7000000 0x8000		/* config space */
+				0xe105400 0x400>;	/* pci bridge */
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/lantiq/danube_easy50712.dts b/arch/mips/boot/dts/lantiq/danube_easy50712.dts
new file mode 100644
index 000000000..1ce20b7d0
--- /dev/null
+++ b/arch/mips/boot/dts/lantiq/danube_easy50712.dts
@@ -0,0 +1,115 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+/include/ "danube.dtsi"
+
+/ {
+	chosen {
+		bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x2000000>;
+	};
+
+	fpi@10000000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		localbus@0 {
+			#address-cells = <2>;
+			#size-cells = <1>;
+			ranges = <0 0 0x0 0x3ffffff /* addrsel0 */
+				1 0 0x4000000 0x4000010>; /* addsel1 */
+			compatible = "lantiq,localbus", "simple-bus";
+
+			nor-boot@0 {
+				compatible = "lantiq,nor";
+				bank-width = <2>;
+				reg = <0 0x0 0x2000000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				partition@0 {
+					label = "uboot";
+					reg = <0x00000 0x10000>; /* 64 KB */
+				};
+
+				partition@10000 {
+					label = "uboot_env";
+					reg = <0x10000 0x10000>; /* 64 KB */
+				};
+
+				partition@20000 {
+					label = "linux";
+					reg = <0x20000 0x3d0000>;
+				};
+
+				partition@400000 {
+					label = "rootfs";
+					reg = <0x400000 0x400000>;
+				};
+			};
+		};
+
+		gpio: pinmux@e100b10 {
+			compatible = "lantiq,danube-pinctrl";
+			pinctrl-names = "default";
+			pinctrl-0 = <&state_default>;
+
+			#gpio-cells = <2>;
+			gpio-controller;
+			reg = <0xe100b10 0xa0>;
+
+			state_default: pinmux {
+				stp {
+					lantiq,groups = "stp";
+					lantiq,function = "stp";
+				};
+				exin {
+					lantiq,groups = "exin1";
+					lantiq,function = "exin";
+				};
+				pci {
+					lantiq,groups = "gnt1";
+					lantiq,function = "pci";
+				};
+				conf_out {
+					lantiq,pins = "io4", "io5", "io6"; /* stp */
+					lantiq,open-drain;
+					lantiq,pull = <0>;
+				};
+			};
+		};
+
+		etop@e180000 {
+			compatible = "lantiq,etop-xway";
+			reg = <0xe180000 0x40000>;
+			interrupt-parent = <&icu0>;
+			interrupts = <73 78>;
+			phy-mode = "rmii";
+			mac-address = [ 00 11 22 33 44 55 ];
+		};
+
+		stp0: stp@e100bb0 {
+			#gpio-cells = <2>;
+			compatible = "lantiq,gpio-stp-xway";
+			gpio-controller;
+			reg = <0xe100bb0 0x40>;
+
+			lantiq,shadow = <0xfff>;
+			lantiq,groups = <0x3>;
+		};
+
+		pci@e105400 {
+			lantiq,bus-clock = <33333333>;
+			interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+			interrupt-map = <
+				0x7000 0 0 1 &icu0 29 1 // slot 14, irq 29
+			>;
+			gpios-reset = <&gpio 21 0>;
+			req-mask = <0x1>;		/* GNT1 */
+		};
+
+	};
+};
diff --git a/arch/mips/boot/dts/loongson/Makefile b/arch/mips/boot/dts/loongson/Makefile
new file mode 100644
index 000000000..5c6433e44
--- /dev/null
+++ b/arch/mips/boot/dts/loongson/Makefile
@@ -0,0 +1,9 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_MACH_LOONGSON64)	+= loongson64_2core_2k1000.dtb
+dtb-$(CONFIG_MACH_LOONGSON64)	+= loongson64c_4core_ls7a.dtb
+dtb-$(CONFIG_MACH_LOONGSON64)	+= loongson64c_4core_rs780e.dtb
+dtb-$(CONFIG_MACH_LOONGSON64)	+= loongson64c_8core_rs780e.dtb
+dtb-$(CONFIG_MACH_LOONGSON64)	+= loongson64g_4core_ls7a.dtb
+dtb-$(CONFIG_MACH_LOONGSON64)	+= loongson64v_4core_virtio.dtb
+
+obj-$(CONFIG_BUILTIN_DTB)	+= $(addsuffix .o, $(dtb-y))
diff --git a/arch/mips/boot/dts/loongson/loongson64-2k1000.dtsi b/arch/mips/boot/dts/loongson/loongson64-2k1000.dtsi
new file mode 100644
index 000000000..c16b52130
--- /dev/null
+++ b/arch/mips/boot/dts/loongson/loongson64-2k1000.dtsi
@@ -0,0 +1,293 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/dts-v1/;
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "loongson,loongson2k1000";
+
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "loongson,gs264";
+			reg = <0x0>;
+			#clock-cells = <1>;
+			clocks = <&cpu_clk>;
+		};
+	};
+
+	memory@200000 {
+		compatible = "memory";
+		device_type = "memory";
+		reg = <0x00000000 0x00200000 0x00000000 0x0ee00000>, /* 238 MB at 2 MB */
+			<0x00000000 0x20000000 0x00000000 0x1f000000>, /* 496 MB at 512 MB */
+			<0x00000001 0x10000000 0x00000001 0xb0000000>; /* 6912 MB at 4352MB */
+	};
+
+	cpu_clk: cpu_clk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <800000000>;
+	};
+
+	cpuintc: interrupt-controller {
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		compatible = "mti,cpu-interrupt-controller";
+	};
+
+	package0: bus@10000000 {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges = <0 0x10000000 0 0x10000000 0 0x10000000 /* ioports */
+			0 0x40000000 0 0x40000000 0 0x40000000
+			0xfe 0x00000000 0xfe 0x00000000 0 0x40000000>;
+
+		pm: reset-controller@1fe07000 {
+			compatible = "loongson,ls2k-pm";
+			reg = <0 0x1fe07000 0 0x422>;
+		};
+
+		liointc0: interrupt-controller@1fe11400 {
+			compatible = "loongson,liointc-2.0";
+			reg = <0 0x1fe11400 0 0x40>,
+				<0 0x1fe11040 0 0x8>,
+				<0 0x1fe11140 0 0x8>;
+			reg-names = "main", "isr0", "isr1";
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&cpuintc>;
+			interrupts = <2>;
+			interrupt-names = "int0";
+
+			loongson,parent_int_map = <0xffffffff>, /* int0 */
+						<0x00000000>, /* int1 */
+						<0x00000000>, /* int2 */
+						<0x00000000>; /* int3 */
+		};
+
+		liointc1: interrupt-controller@1fe11440 {
+			compatible = "loongson,liointc-2.0";
+			reg = <0 0x1fe11440 0 0x40>,
+				<0 0x1fe11048 0 0x8>,
+				<0 0x1fe11148 0 0x8>;
+			reg-names = "main", "isr0", "isr1";
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&cpuintc>;
+			interrupts = <3>;
+			interrupt-names = "int1";
+
+			loongson,parent_int_map = <0x00000000>, /* int0 */
+						<0xffffffff>, /* int1 */
+						<0x00000000>, /* int2 */
+						<0x00000000>; /* int3 */
+		};
+
+		uart0: serial@1fe00000 {
+			compatible = "ns16550a";
+			reg = <0 0x1fe00000 0 0x8>;
+			clock-frequency = <125000000>;
+			interrupt-parent = <&liointc0>;
+			interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+			no-loopback-test;
+		};
+
+		pci@1a000000 {
+			compatible = "loongson,ls2k-pci";
+			device_type = "pci";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			#interrupt-cells = <2>;
+
+			reg = <0 0x1a000000 0 0x02000000>,
+				<0xfe 0x00000000 0 0x20000000>;
+
+			ranges = <0x01000000 0x0 0x00000000 0x0 0x18000000  0x0 0x00010000>,
+				 <0x02000000 0x0 0x40000000 0x0 0x40000000  0x0 0x40000000>;
+
+			gmac@3,0 {
+				compatible = "pci0014,7a03.0",
+						   "pci0014,7a03",
+						   "pciclass0c0320",
+						   "pciclass0c03";
+
+				reg = <0x1800 0x0 0x0 0x0 0x0>;
+				interrupts = <12 IRQ_TYPE_LEVEL_LOW>,
+					     <13 IRQ_TYPE_LEVEL_LOW>;
+				interrupt-names = "macirq", "eth_lpi";
+				interrupt-parent = <&liointc0>;
+				phy-mode = "rgmii";
+				mdio {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					compatible = "snps,dwmac-mdio";
+					phy0: ethernet-phy@0 {
+						reg = <0>;
+					};
+				};
+			};
+
+			gmac@3,1 {
+				compatible = "pci0014,7a03.0",
+						   "pci0014,7a03",
+						   "pciclass0c0320",
+						   "pciclass0c03",
+						   "loongson, pci-gmac";
+
+				reg = <0x1900 0x0 0x0 0x0 0x0>;
+				interrupts = <14 IRQ_TYPE_LEVEL_LOW>,
+					     <15 IRQ_TYPE_LEVEL_LOW>;
+				interrupt-names = "macirq", "eth_lpi";
+				interrupt-parent = <&liointc0>;
+				phy-mode = "rgmii";
+				mdio {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					compatible = "snps,dwmac-mdio";
+					phy1: ethernet-phy@1 {
+						reg = <0>;
+					};
+				};
+			};
+
+			ehci@4,1 {
+				compatible = "pci0014,7a14.0",
+						   "pci0014,7a14",
+						   "pciclass0c0320",
+						   "pciclass0c03";
+
+				reg = <0x2100 0x0 0x0 0x0 0x0>;
+				interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
+				interrupt-parent = <&liointc1>;
+			};
+
+			ohci@4,2 {
+				compatible = "pci0014,7a24.0",
+						   "pci0014,7a24",
+						   "pciclass0c0310",
+						   "pciclass0c03";
+
+				reg = <0x2200 0x0 0x0 0x0 0x0>;
+				interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+				interrupt-parent = <&liointc1>;
+			};
+
+			sata@8,0 {
+				compatible = "pci0014,7a08.0",
+						   "pci0014,7a08",
+						   "pciclass010601",
+						   "pciclass0106";
+
+				reg = <0x4000 0x0 0x0 0x0 0x0>;
+				interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+				interrupt-parent = <&liointc0>;
+			};
+
+			pci_bridge@9,0 {
+				compatible = "pci0014,7a19.0",
+						   "pci0014,7a19",
+						   "pciclass060400",
+						   "pciclass0604";
+
+				reg = <0x4800 0x0 0x0 0x0 0x0>;
+				#interrupt-cells = <1>;
+				interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+				interrupt-parent = <&liointc1>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &liointc1 0 IRQ_TYPE_LEVEL_LOW>;
+				external-facing;
+			};
+
+			pci_bridge@a,0 {
+				compatible = "pci0014,7a09.0",
+						   "pci0014,7a09",
+						   "pciclass060400",
+						   "pciclass0604";
+
+				reg = <0x5000 0x0 0x0 0x0 0x0>;
+				#interrupt-cells = <1>;
+				interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+				interrupt-parent = <&liointc1>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &liointc1 1 IRQ_TYPE_LEVEL_LOW>;
+				external-facing;
+			};
+
+			pci_bridge@b,0 {
+				compatible = "pci0014,7a09.0",
+						   "pci0014,7a09",
+						   "pciclass060400",
+						   "pciclass0604";
+
+				reg = <0x5800 0x0 0x0 0x0 0x0>;
+				#interrupt-cells = <1>;
+				interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+				interrupt-parent = <&liointc1>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &liointc1 2 IRQ_TYPE_LEVEL_LOW>;
+				external-facing;
+			};
+
+			pci_bridge@c,0 {
+				compatible = "pci0014,7a09.0",
+						   "pci0014,7a09",
+						   "pciclass060400",
+						   "pciclass0604";
+
+				reg = <0x6000 0x0 0x0 0x0 0x0>;
+				#interrupt-cells = <1>;
+				interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+				interrupt-parent = <&liointc1>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &liointc1 3 IRQ_TYPE_LEVEL_LOW>;
+				external-facing;
+			};
+
+			pci_bridge@d,0 {
+				compatible = "pci0014,7a19.0",
+						   "pci0014,7a19",
+						   "pciclass060400",
+						   "pciclass0604";
+
+				reg = <0x6800 0x0 0x0 0x0 0x0>;
+				#interrupt-cells = <1>;
+				interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+				interrupt-parent = <&liointc1>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &liointc1 4 IRQ_TYPE_LEVEL_LOW>;
+				external-facing;
+			};
+
+			pci_bridge@e,0 {
+				compatible = "pci0014,7a09.0",
+						   "pci0014,7a09",
+						   "pciclass060400",
+						   "pciclass0604";
+
+				reg = <0x7000 0x0 0x0 0x0 0x0>;
+				#interrupt-cells = <1>;
+				interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+				interrupt-parent = <&liointc1>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &liointc1 5 IRQ_TYPE_LEVEL_LOW>;
+				external-facing;
+			};
+
+		};
+	};
+};
+
diff --git a/arch/mips/boot/dts/loongson/loongson64_2core_2k1000.dts b/arch/mips/boot/dts/loongson/loongson64_2core_2k1000.dts
new file mode 100644
index 000000000..e31d2ee65
--- /dev/null
+++ b/arch/mips/boot/dts/loongson/loongson64_2core_2k1000.dts
@@ -0,0 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/dts-v1/;
+
+#include "loongson64-2k1000.dtsi"
+
+/ {
+	compatible = "loongson,loongson64-2core-2k1000";
+};
+
diff --git a/arch/mips/boot/dts/loongson/loongson64c-package.dtsi b/arch/mips/boot/dts/loongson/loongson64c-package.dtsi
new file mode 100644
index 000000000..5bb876a4d
--- /dev/null
+++ b/arch/mips/boot/dts/loongson/loongson64c-package.dtsi
@@ -0,0 +1,64 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpuintc: interrupt-controller {
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		compatible = "mti,cpu-interrupt-controller";
+	};
+
+	package0: bus@1fe00000 {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges = <0 0x1fe00000 0 0x1fe00000 0x100000
+			0 0x3ff00000 0 0x3ff00000 0x100000
+			/* 3A HT Config Space */
+			0xefd 0xfb000000 0xefd 0xfb000000 0x10000000
+			/* 3B HT Config Space */
+			0x1efd 0xfb000000 0x1efd 0xfb000000 0x10000000>;
+
+		liointc: interrupt-controller@3ff01400 {
+			compatible = "loongson,liointc-1.0";
+			reg = <0 0x3ff01400 0x64>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&cpuintc>;
+			interrupts = <2>, <3>;
+			interrupt-names = "int0", "int1";
+
+			loongson,parent_int_map = <0xf0ffffff>, /* int0 */
+						<0x0f000000>, /* int1 */
+						<0x00000000>, /* int2 */
+						<0x00000000>; /* int3 */
+
+		};
+
+		cpu_uart0: serial@1fe001e0 {
+			compatible = "ns16550a";
+			reg = <0 0x1fe001e0 0x8>;
+			clock-frequency = <33000000>;
+			interrupt-parent = <&liointc>;
+			interrupts = <10 IRQ_TYPE_LEVEL_HIGH>;
+			no-loopback-test;
+		};
+
+		cpu_uart1: serial@1fe001e8 {
+			status = "disabled";
+			compatible = "ns16550a";
+			reg = <0 0x1fe001e8 0x8>;
+			clock-frequency = <33000000>;
+			interrupts = <10 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-parent = <&liointc>;
+			no-loopback-test;
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/loongson/loongson64c_4core_ls7a.dts b/arch/mips/boot/dts/loongson/loongson64c_4core_ls7a.dts
new file mode 100644
index 000000000..c7ea4f1c0
--- /dev/null
+++ b/arch/mips/boot/dts/loongson/loongson64c_4core_ls7a.dts
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/dts-v1/;
+
+#include "loongson64c-package.dtsi"
+#include "ls7a-pch.dtsi"
+
+/ {
+	compatible = "loongson,loongson64c-4core-ls7a";
+};
+
+&package0 {
+	htvec: interrupt-controller@efdfb000080 {
+		compatible = "loongson,htvec-1.0";
+		reg = <0xefd 0xfb000080 0x40>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&liointc>;
+		interrupts = <24 IRQ_TYPE_LEVEL_HIGH>,
+			     <25 IRQ_TYPE_LEVEL_HIGH>,
+			     <26 IRQ_TYPE_LEVEL_HIGH>,
+			     <27 IRQ_TYPE_LEVEL_HIGH>;
+	};
+};
+
+&pch {
+	msi: msi-controller@2ff00000 {
+		compatible = "loongson,pch-msi-1.0";
+		reg = <0 0x2ff00000 0 0x8>;
+		interrupt-controller;
+		msi-controller;
+		loongson,msi-base-vec = <64>;
+		loongson,msi-num-vecs = <64>;
+		interrupt-parent = <&htvec>;
+	};
+};
diff --git a/arch/mips/boot/dts/loongson/loongson64c_4core_rs780e.dts b/arch/mips/boot/dts/loongson/loongson64c_4core_rs780e.dts
new file mode 100644
index 000000000..d681a295d
--- /dev/null
+++ b/arch/mips/boot/dts/loongson/loongson64c_4core_rs780e.dts
@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/dts-v1/;
+
+#include "loongson64c-package.dtsi"
+#include "rs780e-pch.dtsi"
+
+/ {
+	compatible = "loongson,loongson64c-4core-rs780e";
+};
+
+&package0 {
+	htpic: interrupt-controller@efdfb000080 {
+		compatible = "loongson,htpic-1.0";
+		reg = <0xefd 0xfb000080 0x40>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&liointc>;
+		interrupts = <24 IRQ_TYPE_LEVEL_HIGH>,
+				<25 IRQ_TYPE_LEVEL_HIGH>,
+				<26 IRQ_TYPE_LEVEL_HIGH>,
+				<27 IRQ_TYPE_LEVEL_HIGH>;
+	};
+};
diff --git a/arch/mips/boot/dts/loongson/loongson64c_8core_rs780e.dts b/arch/mips/boot/dts/loongson/loongson64c_8core_rs780e.dts
new file mode 100644
index 000000000..3c2044142
--- /dev/null
+++ b/arch/mips/boot/dts/loongson/loongson64c_8core_rs780e.dts
@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/dts-v1/;
+
+#include "loongson64c-package.dtsi"
+#include "rs780e-pch.dtsi"
+
+/ {
+	compatible = "loongson,loongson64c-8core-rs780e";
+};
+
+&package0 {
+	htpic: interrupt-controller@1efdfb000080 {
+		compatible = "loongson,htpic-1.0";
+		reg = <0x1efd 0xfb000080 0x40>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&liointc>;
+		interrupts = <24 IRQ_TYPE_LEVEL_HIGH>,
+				<25 IRQ_TYPE_LEVEL_HIGH>,
+				<26 IRQ_TYPE_LEVEL_HIGH>,
+				<27 IRQ_TYPE_LEVEL_HIGH>;
+	};
+};
diff --git a/arch/mips/boot/dts/loongson/loongson64g-package.dtsi b/arch/mips/boot/dts/loongson/loongson64g-package.dtsi
new file mode 100644
index 000000000..d4314f62c
--- /dev/null
+++ b/arch/mips/boot/dts/loongson/loongson64g-package.dtsi
@@ -0,0 +1,61 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpuintc: interrupt-controller {
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		compatible = "mti,cpu-interrupt-controller";
+	};
+
+	package0: bus@1fe00000 {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges = <0 0x1fe00000 0 0x1fe00000 0x100000
+			0 0x3ff00000 0 0x3ff00000 0x100000
+			0xefd 0xfb000000 0xefd 0xfb000000 0x10000000>;
+
+		liointc: interrupt-controller@3ff01400 {
+			compatible = "loongson,liointc-1.0";
+			reg = <0 0x3ff01400 0x64>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&cpuintc>;
+			interrupts = <2>, <3>;
+			interrupt-names = "int0", "int1";
+
+			loongson,parent_int_map = <0x00ffffff>, /* int0 */
+						<0xff000000>, /* int1 */
+						<0x00000000>, /* int2 */
+						<0x00000000>; /* int3 */
+
+		};
+
+		cpu_uart0: serial@1fe00100 {
+			compatible = "ns16550a";
+			reg = <0 0x1fe00100 0x10>;
+			clock-frequency = <100000000>;
+			interrupt-parent = <&liointc>;
+			interrupts = <10 IRQ_TYPE_LEVEL_HIGH>;
+			no-loopback-test;
+		};
+
+		cpu_uart1: serial@1fe00110 {
+			status = "disabled";
+			compatible = "ns16550a";
+			reg = <0 0x1fe00110 0x10>;
+			clock-frequency = <100000000>;
+			interrupts = <15 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-parent = <&liointc>;
+			no-loopback-test;
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/loongson/loongson64g_4core_ls7a.dts b/arch/mips/boot/dts/loongson/loongson64g_4core_ls7a.dts
new file mode 100644
index 000000000..c945f8565
--- /dev/null
+++ b/arch/mips/boot/dts/loongson/loongson64g_4core_ls7a.dts
@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/dts-v1/;
+
+#include "loongson64g-package.dtsi"
+#include "ls7a-pch.dtsi"
+
+/ {
+	compatible = "loongson,loongson64g-4core-ls7a";
+};
+
+&package0 {
+	htvec: interrupt-controller@efdfb000080 {
+		compatible = "loongson,htvec-1.0";
+		reg = <0xefd 0xfb000080 0x40>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&liointc>;
+		interrupts = <24 IRQ_TYPE_LEVEL_HIGH>,
+			     <25 IRQ_TYPE_LEVEL_HIGH>,
+			     <26 IRQ_TYPE_LEVEL_HIGH>,
+			     <27 IRQ_TYPE_LEVEL_HIGH>,
+			     <28 IRQ_TYPE_LEVEL_HIGH>,
+			     <29 IRQ_TYPE_LEVEL_HIGH>,
+			     <30 IRQ_TYPE_LEVEL_HIGH>,
+			     <31 IRQ_TYPE_LEVEL_HIGH>;
+	};
+};
+
+&pch {
+	msi: msi-controller@2ff00000 {
+		compatible = "loongson,pch-msi-1.0";
+		reg = <0 0x2ff00000 0 0x8>;
+		interrupt-controller;
+		msi-controller;
+		loongson,msi-base-vec = <64>;
+		loongson,msi-num-vecs = <192>;
+		interrupt-parent = <&htvec>;
+	};
+};
diff --git a/arch/mips/boot/dts/loongson/loongson64v_4core_virtio.dts b/arch/mips/boot/dts/loongson/loongson64v_4core_virtio.dts
new file mode 100644
index 000000000..d0588d81e
--- /dev/null
+++ b/arch/mips/boot/dts/loongson/loongson64v_4core_virtio.dts
@@ -0,0 +1,102 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/dts-v1/;
+/ {
+	compatible = "loongson,loongson64v-4core-virtio";
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpuintc: interrupt-controller {
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		compatible = "mti,cpu-interrupt-controller";
+	};
+
+	package0: bus@1fe00000 {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges = <0 0x1fe00000 0 0x1fe00000 0x100000
+			0 0x3ff00000 0 0x3ff00000 0x100000
+			0xefd 0xfb000000 0xefd 0xfb000000 0x10000000>;
+
+		liointc: interrupt-controller@3ff01400 {
+			compatible = "loongson,liointc-1.0";
+			reg = <0 0x3ff01400 0x64>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&cpuintc>;
+			interrupts = <2>, <3>;
+			interrupt-names = "int0", "int1";
+
+			loongson,parent_int_map = <0x00000001>, /* int0 */
+						<0xfffffffe>, /* int1 */
+						<0x00000000>, /* int2 */
+						<0x00000000>; /* int3 */
+
+		};
+
+		cpu_uart0: serial@1fe001e0 {
+			compatible = "ns16550a";
+			reg = <0 0x1fe001e0 0x8>;
+			clock-frequency = <33000000>;
+			interrupt-parent = <&liointc>;
+			interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+			no-loopback-test;
+		};
+	};
+
+	bus@10000000 {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges = <0 0x10000000 0 0x10000000 0 0x10000000 /* PIO & CONF & APB */
+				0 0x40000000 0 0x40000000 0 0x40000000>; /* PCI MEM */
+
+		rtc0: rtc@10081000 {
+			compatible = "google,goldfish-rtc";
+			reg = <0 0x10081000 0 0x1000>;
+			interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-parent = <&liointc>;
+		};
+
+		pci@1a000000 {
+			compatible = "pci-host-ecam-generic";
+			device_type = "pci";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			#interrupt-cells = <1>;
+
+			bus-range = <0x0 0x1f>;
+			reg = <0 0x1a000000 0 0x02000000>;
+
+			ranges = <0x01000000 0x0 0x00004000 0x0 0x18004000 0x0 0x0000c000>,
+				 <0x02000000 0x0 0x40000000 0x0 0x40000000 0x0 0x40000000>;
+
+			interrupt-map = <
+				0x0000 0x0 0x0  0x1  &liointc  0x2 IRQ_TYPE_LEVEL_HIGH
+				0x0800 0x0 0x0  0x1  &liointc  0x3 IRQ_TYPE_LEVEL_HIGH
+				0x1000 0x0 0x0  0x1  &liointc  0x4 IRQ_TYPE_LEVEL_HIGH
+				0x1800 0x0 0x0  0x1  &liointc  0x5 IRQ_TYPE_LEVEL_HIGH
+				>;
+
+			interrupt-map-mask = <0x1800 0x0 0x0  0x7>;
+		};
+
+		isa@18000000 {
+			compatible = "isa";
+			#address-cells = <2>;
+			#size-cells = <1>;
+			ranges = <1 0 0 0x18000000 0x4000>;
+		};
+	};
+
+	hypervisor {
+		compatible = "linux,kvm";
+	};
+};
diff --git a/arch/mips/boot/dts/loongson/ls7a-pch.dtsi b/arch/mips/boot/dts/loongson/ls7a-pch.dtsi
new file mode 100644
index 000000000..ed99ee316
--- /dev/null
+++ b/arch/mips/boot/dts/loongson/ls7a-pch.dtsi
@@ -0,0 +1,418 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/ {
+	pch: bus@10000000 {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges = <0 0x10000000 0 0x10000000 0 0x10000000 /* PIO & CONF & APB */
+				0 0x20000000 0 0x20000000 0 0x10000000
+				0 0x40000000 0 0x40000000 0 0x40000000 /* PCI MEM */
+				0xe00 0x00000000 0xe00 0x00000000 0x100 0x0000000>;
+
+		pic: interrupt-controller@10000000 {
+			compatible = "loongson,pch-pic-1.0";
+			reg = <0 0x10000000 0 0x400>;
+			interrupt-controller;
+			interrupt-parent = <&htvec>;
+			loongson,pic-base-vec = <0>;
+			#interrupt-cells = <2>;
+		};
+
+		ls7a_uart0: serial@10080000 {
+			compatible = "ns16550a";
+			reg = <0 0x10080000 0 0x100>;
+			clock-frequency = <50000000>;
+			interrupt-parent = <&pic>;
+			interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
+			no-loopback-test;
+		};
+
+		ls7a_uart1: serial@10080100 {
+			status = "disabled";
+			compatible = "ns16550a";
+			reg = <0 0x10080100 0 0x100>;
+			clock-frequency = <50000000>;
+			interrupt-parent = <&pic>;
+			interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
+			no-loopback-test;
+		};
+
+		ls7a_uart2: serial@10080200 {
+			status = "disabled";
+			compatible = "ns16550a";
+			reg = <0 0x10080200 0 0x100>;
+			clock-frequency = <50000000>;
+			interrupt-parent = <&pic>;
+			interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
+			no-loopback-test;
+		};
+
+		ls7a_uart3: serial@10080300 {
+			status = "disabled";
+			compatible = "ns16550a";
+			reg = <0 0x10080300 0 0x100>;
+			clock-frequency = <50000000>;
+			interrupt-parent = <&pic>;
+			interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
+			no-loopback-test;
+		};
+
+		pci@1a000000 {
+			compatible = "loongson,ls7a-pci";
+			device_type = "pci";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			#interrupt-cells = <2>;
+			msi-parent = <&msi>;
+
+			reg = <0 0x1a000000 0 0x02000000>,
+				<0xefe 0x00000000 0 0x20000000>;
+
+			ranges = <0x01000000 0x0 0x00020000 0x0 0x18020000 0x0 0x00020000>,
+				 <0x02000000 0x0 0x40000000 0x0 0x40000000 0x0 0x40000000>;
+
+			ohci@4,0 {
+				compatible = "pci0014,7a24.0",
+						   "pci0014,7a24",
+						   "pciclass0c0310",
+						   "pciclass0c03";
+
+				reg = <0x2000 0x0 0x0 0x0 0x0>;
+				interrupts = <49 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-parent = <&pic>;
+			};
+
+			ehci@4,1 {
+				compatible = "pci0014,7a14.0",
+						   "pci0014,7a14",
+						   "pciclass0c0320",
+						   "pciclass0c03";
+
+				reg = <0x2100 0x0 0x0 0x0 0x0>;
+				interrupts = <48 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-parent = <&pic>;
+			};
+
+			ohci@5,0 {
+				compatible = "pci0014,7a24.0",
+						   "pci0014,7a24",
+						   "pciclass0c0310",
+						   "pciclass0c03";
+
+				reg = <0x2800 0x0 0x0 0x0 0x0>;
+				interrupts = <51 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-parent = <&pic>;
+			};
+
+			ehci@5,1 {
+				compatible = "pci0014,7a14.0",
+						   "pci0014,7a14",
+						   "pciclass0c0320",
+						   "pciclass0c03";
+
+				reg = <0x2900 0x0 0x0 0x0 0x0>;
+				interrupts = <50 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-parent = <&pic>;
+			};
+
+			sata@8,0 {
+				compatible = "pci0014,7a08.0",
+						   "pci0014,7a08",
+						   "pciclass010601",
+						   "pciclass0106";
+
+				reg = <0x4000 0x0 0x0 0x0 0x0>;
+				interrupts = <16 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-parent = <&pic>;
+			};
+
+			sata@8,1 {
+				compatible = "pci0014,7a08.0",
+						   "pci0014,7a08",
+						   "pciclass010601",
+						   "pciclass0106";
+
+				reg = <0x4100 0x0 0x0 0x0 0x0>;
+				interrupts = <17 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-parent = <&pic>;
+			};
+
+			sata@8,2 {
+				compatible = "pci0014,7a08.0",
+						   "pci0014,7a08",
+						   "pciclass010601",
+						   "pciclass0106";
+
+				reg = <0x4200 0x0 0x0 0x0 0x0>;
+				interrupts = <18 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-parent = <&pic>;
+			};
+
+			gpu@6,0 {
+				compatible = "pci0014,7a15.0",
+						   "pci0014,7a15",
+						   "pciclass030200",
+						   "pciclass0302";
+
+				reg = <0x3000 0x0 0x0 0x0 0x0>;
+				interrupts = <29 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-parent = <&pic>;
+			};
+
+			dc@6,1 {
+				compatible = "pci0014,7a06.0",
+						   "pci0014,7a06",
+						   "pciclass030000",
+						   "pciclass0300";
+
+				reg = <0x3100 0x0 0x0 0x0 0x0>;
+				interrupts = <28 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-parent = <&pic>;
+			};
+
+			hda@7,0 {
+				compatible = "pci0014,7a07.0",
+						   "pci0014,7a07",
+						   "pciclass040300",
+						   "pciclass0403";
+
+				reg = <0x3800 0x0 0x0 0x0 0x0>;
+				interrupts = <58 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-parent = <&pic>;
+			};
+
+			gmac@3,0 {
+				compatible = "pci0014,7a03.0",
+						   "pci0014,7a03",
+						   "pciclass020000",
+						   "pciclass0200";
+
+				reg = <0x1800 0x0 0x0 0x0 0x0>;
+				interrupts = <12 IRQ_TYPE_LEVEL_HIGH>,
+					     <13 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "macirq", "eth_lpi";
+				interrupt-parent = <&pic>;
+				phy-mode = "rgmii";
+				mdio {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					compatible = "snps,dwmac-mdio";
+					phy0: ethernet-phy@0 {
+						reg = <0>;
+					};
+				};
+			};
+
+			gmac@3,1 {
+				compatible = "pci0014,7a03.0",
+						   "pci0014,7a03",
+						   "pciclass020000",
+						   "pciclass0200",
+						   "loongson, pci-gmac";
+
+				reg = <0x1900 0x0 0x0 0x0 0x0>;
+				interrupts = <14 IRQ_TYPE_LEVEL_HIGH>,
+					     <15 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "macirq", "eth_lpi";
+				interrupt-parent = <&pic>;
+				phy-mode = "rgmii";
+				mdio {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					compatible = "snps,dwmac-mdio";
+					phy1: ethernet-phy@1 {
+						reg = <0>;
+					};
+				};
+			};
+
+			pci_bridge@9,0 {
+				compatible = "pci0014,7a19.1",
+						   "pci0014,7a19",
+						   "pciclass060400",
+						   "pciclass0604";
+
+				reg = <0x4800 0x0 0x0 0x0 0x0>;
+				interrupts = <32 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-parent = <&pic>;
+
+				#interrupt-cells = <1>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &pic 32 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			pci_bridge@a,0 {
+				compatible = "pci0014,7a09.1",
+						   "pci0014,7a09",
+						   "pciclass060400",
+						   "pciclass0604";
+
+				reg = <0x5000 0x0 0x0 0x0 0x0>;
+				interrupts = <33 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-parent = <&pic>;
+
+				#interrupt-cells = <1>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &pic 33 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			pci_bridge@b,0 {
+				compatible = "pci0014,7a09.1",
+						   "pci0014,7a09",
+						   "pciclass060400",
+						   "pciclass0604";
+
+				reg = <0x5800 0x0 0x0 0x0 0x0>;
+				interrupts = <34 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-parent = <&pic>;
+
+				#interrupt-cells = <1>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &pic 34 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			pci_bridge@c,0 {
+				compatible = "pci0014,7a09.1",
+						   "pci0014,7a09",
+						   "pciclass060400",
+						   "pciclass0604";
+
+				reg = <0x6000 0x0 0x0 0x0 0x0>;
+				interrupts = <35 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-parent = <&pic>;
+
+				#interrupt-cells = <1>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &pic 35 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			pci_bridge@d,0 {
+				compatible = "pci0014,7a19.1",
+						   "pci0014,7a19",
+						   "pciclass060400",
+						   "pciclass0604";
+
+				reg = <0x6800 0x0 0x0 0x0 0x0>;
+				interrupts = <36 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-parent = <&pic>;
+
+				#interrupt-cells = <1>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &pic 36 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			pci_bridge@e,0 {
+				compatible = "pci0014,7a09.1",
+						   "pci0014,7a09",
+						   "pciclass060400",
+						   "pciclass0604";
+
+				reg = <0x7000 0x0 0x0 0x0 0x0>;
+				interrupts = <37 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-parent = <&pic>;
+
+				#interrupt-cells = <1>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &pic 37 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			pci_bridge@f,0 {
+				compatible = "pci0014,7a29.1",
+						   "pci0014,7a29",
+						   "pciclass060400",
+						   "pciclass0604";
+
+				reg = <0x7800 0x0 0x0 0x0 0x0>;
+				interrupts = <40 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-parent = <&pic>;
+
+				#interrupt-cells = <1>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &pic 40 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			pci_bridge@10,0 {
+				compatible = "pci0014,7a19.1",
+						   "pci0014,7a19",
+						   "pciclass060400",
+						   "pciclass0604";
+
+				reg = <0x8000 0x0 0x0 0x0 0x0>;
+				interrupts = <41 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-parent = <&pic>;
+
+				#interrupt-cells = <1>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &pic 41 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			pci_bridge@11,0 {
+				compatible = "pci0014,7a29.1",
+						   "pci0014,7a29",
+						   "pciclass060400",
+						   "pciclass0604";
+
+				reg = <0x8800 0x0 0x0 0x0 0x0>;
+				interrupts = <42 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-parent = <&pic>;
+
+				#interrupt-cells = <1>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &pic 42 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			pci_bridge@12,0 {
+				compatible = "pci0014,7a19.1",
+						   "pci0014,7a19",
+						   "pciclass060400",
+						   "pciclass0604";
+
+				reg = <0x9000 0x0 0x0 0x0 0x0>;
+				interrupts = <43 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-parent = <&pic>;
+
+				#interrupt-cells = <1>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &pic 43 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			pci_bridge@13,0 {
+				compatible = "pci0014,7a29.1",
+						   "pci0014,7a29",
+						   "pciclass060400",
+						   "pciclass0604";
+
+				reg = <0x9800 0x0 0x0 0x0 0x0>;
+				interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-parent = <&pic>;
+
+				#interrupt-cells = <1>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &pic 38 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			pci_bridge@14,0 {
+				compatible = "pci0014,7a19.1",
+						   "pci0014,7a19",
+						   "pciclass060400",
+						   "pciclass0604";
+
+				reg = <0xa000 0x0 0x0 0x0 0x0>;
+				interrupts = <39 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-parent = <&pic>;
+
+				#interrupt-cells = <1>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &pic 39 IRQ_TYPE_LEVEL_HIGH>;
+			};
+		};
+
+		isa@18000000 {
+			compatible = "isa";
+			#address-cells = <2>;
+			#size-cells = <1>;
+			ranges = <1 0 0 0x18000000 0x20000>;
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/loongson/rs780e-pch.dtsi b/arch/mips/boot/dts/loongson/rs780e-pch.dtsi
new file mode 100644
index 000000000..6f459511e
--- /dev/null
+++ b/arch/mips/boot/dts/loongson/rs780e-pch.dtsi
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/ {
+	bus@10000000 {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges = <0 0x10000000 0 0x10000000 0 0x10000000
+				0 0x40000000 0 0x40000000 0 0x40000000
+				0xfd 0xfe000000 0xfd 0xfe000000  0 0x2000000 /* PCI Config Space */>;
+
+		pci@1a000000 {
+			compatible = "loongson,rs780e-pci";
+			device_type = "pci";
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			reg = <0 0x1a000000 0 0x02000000>;
+
+			ranges = <0x01000000 0 0x00004000 0 0x18004000 0 0x0000c000>,
+				 <0x02000000 0 0x40000000 0 0x40000000 0 0x40000000>;
+		};
+
+		isa@18000000 {
+			compatible = "isa";
+			#address-cells = <2>;
+			#size-cells = <1>;
+			ranges = <1 0 0 0x18000000 0x4000>;
+
+			rtc0: rtc@70 {
+				compatible = "motorola,mc146818";
+				reg = <1 0x70 0x8>;
+				interrupts = <8>;
+				interrupt-parent = <&htpic>;
+			};
+
+			acpi@800 {
+				compatible = "loongson,rs780e-acpi";
+				reg = <1 0x800 0x100>;
+			};
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/mscc/Makefile b/arch/mips/boot/dts/mscc/Makefile
new file mode 100644
index 000000000..eeb6b7aae
--- /dev/null
+++ b/arch/mips/boot/dts/mscc/Makefile
@@ -0,0 +1,13 @@
+# SPDX-License-Identifier: GPL-2.0-only
+dtb-$(CONFIG_SOC_VCOREIII)	+= \
+	jaguar2_pcb110.dtb \
+	jaguar2_pcb111.dtb \
+	jaguar2_pcb118.dtb \
+	luton_pcb091.dtb \
+	ocelot_pcb120.dtb \
+	ocelot_pcb123.dtb \
+	serval_pcb105.dtb \
+	serval_pcb106.dtb
+
+
+obj-$(CONFIG_BUILTIN_DTB)	+= $(addsuffix .o, $(dtb-y))
diff --git a/arch/mips/boot/dts/mscc/jaguar2.dtsi b/arch/mips/boot/dts/mscc/jaguar2.dtsi
new file mode 100644
index 000000000..42b2b0a51
--- /dev/null
+++ b/arch/mips/boot/dts/mscc/jaguar2.dtsi
@@ -0,0 +1,167 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Microsemi Corporation
+ */
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "mscc,jr2";
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart2;
+		gpio0 = &gpio;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "mips,mips24KEc";
+			device_type = "cpu";
+			clocks = <&cpu_clk>;
+			reg = <0>;
+		};
+	};
+
+	cpuintc: interrupt-controller {
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		compatible = "mti,cpu-interrupt-controller";
+	};
+
+	cpu_clk: cpu-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <500000000>;
+	};
+
+	ahb_clk: ahb-clk {
+		compatible = "fixed-factor-clock";
+		#clock-cells = <0>;
+		clocks = <&cpu_clk>;
+		clock-div = <2>;
+		clock-mult = <1>;
+	};
+
+	ahb: ahb {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		interrupt-parent = <&intc>;
+
+		cpu_ctrl: syscon@70000000 {
+			compatible = "mscc,ocelot-cpu-syscon", "syscon";
+			reg = <0x70000000 0x2c>;
+		};
+
+		intc: interrupt-controller@70000070 {
+			compatible = "mscc,jaguar2-icpu-intr";
+			reg = <0x70000070 0x94>;
+			#interrupt-cells = <1>;
+			interrupt-controller;
+			interrupt-parent = <&cpuintc>;
+			interrupts = <2>;
+		};
+
+		uart0: serial@70100000 {
+			pinctrl-0 = <&uart_pins>;
+			pinctrl-names = "default";
+			compatible = "ns16550a";
+			reg = <0x70100000 0x20>;
+			interrupts = <6>;
+			clocks = <&ahb_clk>;
+			reg-io-width = <4>;
+			reg-shift = <2>;
+
+			status = "disabled";
+		};
+
+		uart2: serial@70100800 {
+			pinctrl-0 = <&uart2_pins>;
+			pinctrl-names = "default";
+			compatible = "ns16550a";
+			reg = <0x70100800 0x20>;
+			interrupts = <7>;
+			clocks = <&ahb_clk>;
+			reg-io-width = <4>;
+			reg-shift = <2>;
+
+			status = "disabled";
+		};
+
+		gpio: pinctrl@71010038 {
+			compatible = "mscc,jaguar2-pinctrl";
+			reg = <0x71010038 0x90>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&gpio 0 0 64>;
+
+			uart_pins: uart-pins {
+				pins = "GPIO_10", "GPIO_11";
+				function = "uart";
+			};
+
+			uart2_pins: uart2-pins {
+				pins = "GPIO_24", "GPIO_25";
+				function = "uart2";
+			};
+
+			cs1_pins: cs1-pins {
+				pins = "GPIO_16";
+				function = "si";
+			};
+
+			cs2_pins: cs2-pins {
+				pins = "GPIO_17";
+				function = "si";
+			};
+
+			cs3_pins: cs3-pins {
+				pins = "GPIO_18";
+				function = "si";
+			};
+
+			i2c_pins: i2c-pins {
+				pins = "GPIO_14", "GPIO_15";
+				function = "twi";
+			};
+
+			i2c2_pins: i2c2-pins {
+				pins = "GPIO_28", "GPIO_29";
+				function = "twi2";
+			};
+		};
+
+		i2c0: i2c@70100400 {
+			compatible = "mscc,ocelot-i2c", "snps,designware-i2c";
+			status = "disabled";
+			pinctrl-0 = <&i2c_pins>;
+			pinctrl-names = "default";
+			reg = <0x70100400 0x100>, <0x700001b8 0x8>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <8>;
+			clock-frequency = <100000>;
+			clocks = <&ahb_clk>;
+		};
+
+		i2c2: i2c@70100c00 {
+			compatible = "mscc,ocelot-i2c", "snps,designware-i2c";
+			status = "disabled";
+			pinctrl-0 = <&i2c2_pins>;
+			pinctrl-names = "default";
+			reg = <0x70100c00 0x100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <8>;
+			clock-frequency = <100000>;
+			clocks = <&ahb_clk>;
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/mscc/jaguar2_common.dtsi b/arch/mips/boot/dts/mscc/jaguar2_common.dtsi
new file mode 100644
index 000000000..679ff0d8e
--- /dev/null
+++ b/arch/mips/boot/dts/mscc/jaguar2_common.dtsi
@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Microsemi Corporation
+ */
+
+#include "jaguar2.dtsi"
+
+/ {
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+	i2c-sda-hold-time-ns = <300>;
+};
diff --git a/arch/mips/boot/dts/mscc/jaguar2_pcb110.dts b/arch/mips/boot/dts/mscc/jaguar2_pcb110.dts
new file mode 100644
index 000000000..0ea7bc5b5
--- /dev/null
+++ b/arch/mips/boot/dts/mscc/jaguar2_pcb110.dts
@@ -0,0 +1,267 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Microsemi Corporation
+ */
+
+/dts-v1/;
+#include "jaguar2_common.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Jaguar2 Cu8-Sfp16 PCB110 Reference Board";
+	compatible = "mscc,jr2-pcb110", "mscc,jr2";
+
+	aliases {
+		i2c0    = &i2c0;
+		i2c108  = &i2c108;
+		i2c109  = &i2c109;
+		i2c110  = &i2c110;
+		i2c111  = &i2c111;
+		i2c112  = &i2c112;
+		i2c113  = &i2c113;
+		i2c114  = &i2c114;
+		i2c115  = &i2c115;
+		i2c116  = &i2c116;
+		i2c117  = &i2c117;
+		i2c118  = &i2c118;
+		i2c119  = &i2c119;
+		i2c120  = &i2c120;
+		i2c121  = &i2c121;
+		i2c122  = &i2c122;
+		i2c123  = &i2c123;
+		i2c124  = &i2c124;
+		i2c125  = &i2c125;
+		i2c126  = &i2c126;
+		i2c127  = &i2c127;
+		i2c128  = &i2c128;
+		i2c129  = &i2c129;
+		i2c130  = &i2c130;
+		i2c131  = &i2c131;
+		i2c149  = &i2c149;
+		i2c150  = &i2c150;
+		i2c151  = &i2c151;
+		i2c152  = &i2c152;
+	};
+	i2c0_imux: i2c0-imux {
+		compatible = "i2c-mux-pinctrl";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-parent = <&i2c0>;
+		pinctrl-names =
+			"i2c149", "i2c150", "i2c151", "i2c152", "idle";
+		pinctrl-0 = <&i2cmux_0>;
+		pinctrl-1 = <&i2cmux_1>;
+		pinctrl-2 = <&i2cmux_2>;
+		pinctrl-3 = <&i2cmux_3>;
+		pinctrl-4 = <&i2cmux_pins_i>;
+		i2c149: i2c@0 {
+			reg = <0x0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c150: i2c@1 {
+			reg = <0x1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c151: i2c@2 {
+			reg = <0x2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c152: i2c@3 {
+			reg = <0x3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+	i2c0_emux: i2c0-emux {
+		compatible = "i2c-mux-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-parent = <&i2c0>;
+		mux-gpios = <&gpio 51 GPIO_ACTIVE_HIGH
+			     &gpio 52 GPIO_ACTIVE_HIGH
+			     &gpio 53 GPIO_ACTIVE_HIGH
+			     &gpio 58 GPIO_ACTIVE_HIGH
+			     &gpio 59 GPIO_ACTIVE_HIGH>;
+		idle-state = <0x0>;
+		i2c108: i2c@10 {
+			reg = <0x10>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c109: i2c@11 {
+			reg = <0x11>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c110: i2c@12 {
+			reg = <0x12>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c111: i2c@13 {
+			reg = <0x13>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c112: i2c@14 {
+			reg = <0x14>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c113: i2c@15 {
+			reg = <0x15>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c114: i2c@16 {
+			reg = <0x16>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c115: i2c@17 {
+			reg = <0x17>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c116: i2c@8 {
+			reg = <0x8>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c117: i2c@9 {
+			reg = <0x9>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c118: i2c@a {
+			reg = <0xa>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c119: i2c@b {
+			reg = <0xb>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c120: i2c@c {
+			reg = <0xc>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c121: i2c@d {
+			reg = <0xd>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c122: i2c@e {
+			reg = <0xe>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c123: i2c@f {
+			reg = <0xf>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&gpio {
+	synce_pins: synce-pins {
+		// GPIO 16 == SI_nCS1
+		pins = "GPIO_16";
+		function = "si";
+	};
+	synce_builtin_pins: synce-builtin-pins {
+		// GPIO 49 == SI_nCS13
+		pins = "GPIO_49";
+		function = "si";
+	};
+	i2cmux_pins_i: i2cmux-pins {
+		pins = "GPIO_17", "GPIO_18", "GPIO_20", "GPIO_21";
+		function = "twi_scl_m";
+		output-low;
+	};
+	i2cmux_0: i2cmux-0-pins {
+		pins = "GPIO_17";
+		function = "twi_scl_m";
+		output-high;
+	};
+	i2cmux_1: i2cmux-1-pins {
+		pins = "GPIO_18";
+		function = "twi_scl_m";
+		output-high;
+	};
+	i2cmux_2: i2cmux-2-pins {
+		pins = "GPIO_20";
+		function = "twi_scl_m";
+		output-high;
+	};
+	i2cmux_3: i2cmux-3-pins {
+		pins = "GPIO_21";
+		function = "twi_scl_m";
+		output-high;
+	};
+};
+
+&i2c0 {
+	pca9545@70 {
+		compatible = "nxp,pca9545";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+		i2c124: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+		i2c125: i2c@1 {
+			/* FMC B */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+		i2c126: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+		i2c127: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+	pca9545@71 {
+		compatible = "nxp,pca9545";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+		i2c128: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+		i2c129: i2c@1 {
+			/* FMC B */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+		i2c130: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+		i2c131: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/mscc/jaguar2_pcb111.dts b/arch/mips/boot/dts/mscc/jaguar2_pcb111.dts
new file mode 100644
index 000000000..05d8c6a96
--- /dev/null
+++ b/arch/mips/boot/dts/mscc/jaguar2_pcb111.dts
@@ -0,0 +1,107 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2018 Microsemi Corporation
+ */
+
+/dts-v1/;
+#include "jaguar2_common.dtsi"
+
+/ {
+	model = "Jaguar2 Cu48 PCB111 Reference Board";
+	compatible = "mscc,jr2-pcb111", "mscc,jr2";
+
+	aliases {
+		i2c0    = &i2c0;
+		i2c149  = &i2c149;
+		i2c150  = &i2c150;
+		i2c151  = &i2c151;
+		i2c152  = &i2c152;
+		i2c203  = &i2c203;
+	};
+
+	i2c0_imux: i2c0-imux {
+		compatible = "i2c-mux-pinctrl";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-parent = <&i2c0>;
+		pinctrl-names =
+			"i2c149", "i2c150", "i2c151", "i2c152", "i2c203", "idle";
+		pinctrl-0 = <&i2cmux_0>;
+		pinctrl-1 = <&i2cmux_1>;
+		pinctrl-2 = <&i2cmux_2>;
+		pinctrl-3 = <&i2cmux_3>;
+		pinctrl-4 = <&i2cmux_pins_i>; // Added by convention for PoE
+		pinctrl-5 = <&i2cmux_pins_i>;
+		i2c149: i2c@0 {
+			reg = <0x0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c150: i2c@1 {
+			reg = <0x1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c151: i2c@2 {
+			reg = <0x2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c152: i2c@3 {
+			reg = <0x3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c203: i2c@4 {
+			reg = <0x4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&gpio {
+	synce_builtin_pins: synce-builtin-pins {
+		// GPIO 49 == SI_nCS13
+		pins = "GPIO_49";
+		function = "si";
+	};
+	cpld_pins: cpld-pins {
+		// GPIO 50 == SI_nCS14
+		pins = "GPIO_50";
+		function = "si";
+	};
+	cpld_fifo_pins: synce-builtin-pins {
+		// GPIO 51 == SI_nCS15
+		pins = "GPIO_51";
+		function = "si";
+	};
+};
+
+&gpio {
+	i2cmux_pins_i: i2cmux-pins {
+		pins = "GPIO_17", "GPIO_18";
+		function = "twi_scl_m";
+		output-low;
+	};
+	i2cmux_0: i2cmux-0-pins {
+		pins = "GPIO_17";
+		function = "twi_scl_m";
+		output-high;
+	};
+	i2cmux_1: i2cmux-1-pins {
+		pins = "GPIO_18";
+		function = "twi_scl_m";
+		output-high;
+	};
+	i2cmux_2: i2cmux-2-pins {
+		pins = "GPIO_20";
+		function = "twi_scl_m";
+		output-high;
+	};
+	i2cmux_3: i2cmux-3-pins {
+		pins = "GPIO_21";
+		function = "twi_scl_m";
+		output-high;
+	};
+};
diff --git a/arch/mips/boot/dts/mscc/jaguar2_pcb118.dts b/arch/mips/boot/dts/mscc/jaguar2_pcb118.dts
new file mode 100644
index 000000000..cf2cf591a
--- /dev/null
+++ b/arch/mips/boot/dts/mscc/jaguar2_pcb118.dts
@@ -0,0 +1,57 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2018 Microsemi Corporation
+ */
+
+/dts-v1/;
+#include "jaguar2_common.dtsi"
+
+/ {
+	model = "Jaguar2/Aquantia PCB118 Reference Board";
+	compatible = "mscc,jr2-pcb118", "mscc,jr2";
+
+	aliases {
+		i2c150  = &i2c150;
+		i2c151  = &i2c151;
+	};
+
+	i2c0_imux: i2c0-imux {
+		compatible = "i2c-mux-pinctrl";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-parent = <&i2c0>;
+		pinctrl-names =
+			"i2c150", "i2c151", "idle";
+		pinctrl-0 = <&i2cmux_0>;
+		pinctrl-1 = <&i2cmux_1>;
+		pinctrl-2 = <&i2cmux_pins_i>;
+		i2c150: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c151: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&gpio {
+	i2cmux_pins_i: i2cmux-pins {
+		pins = "GPIO_17", "GPIO_16";
+		function = "twi_scl_m";
+		output-low;
+	};
+	i2cmux_0: i2cmux-0-pins {
+		pins = "GPIO_17";
+		function = "twi_scl_m";
+		output-high;
+	};
+	i2cmux_1: i2cmux-1-pins {
+		pins = "GPIO_16";
+		function = "twi_scl_m";
+		output-high;
+	};
+};
diff --git a/arch/mips/boot/dts/mscc/luton.dtsi b/arch/mips/boot/dts/mscc/luton.dtsi
new file mode 100644
index 000000000..2a170b84c
--- /dev/null
+++ b/arch/mips/boot/dts/mscc/luton.dtsi
@@ -0,0 +1,116 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/* Copyright (c) 2020 Microsemi Corporation */
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "mscc,luton";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "mips,mips24KEc";
+			device_type = "cpu";
+			clocks = <&cpu_clk>;
+			reg = <0>;
+		};
+	};
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	cpuintc: interrupt-controller {
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		compatible = "mti,cpu-interrupt-controller";
+	};
+
+	cpu_clk: cpu-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <416666666>;
+	};
+
+	ahb_clk: ahb-clk {
+		compatible = "fixed-factor-clock";
+		#clock-cells = <0>;
+		clocks = <&cpu_clk>;
+		clock-div = <2>;
+		clock-mult = <1>;
+	};
+
+	ahb@60000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x60000000 0x20000000>;
+
+		interrupt-parent = <&intc>;
+
+		cpu_ctrl: syscon@10000000 {
+			compatible = "mscc,ocelot-cpu-syscon", "syscon";
+			reg = <0x10000000 0x2c>;
+		};
+
+		intc: interrupt-controller@10000084 {
+			compatible = "mscc,luton-icpu-intr";
+			reg = <0x10000084 0x70>;
+			#interrupt-cells = <1>;
+			interrupt-controller;
+			interrupt-parent = <&cpuintc>;
+			interrupts = <2>;
+		};
+
+		uart0: serial@10100000 {
+			pinctrl-0 = <&uart_pins>;
+			pinctrl-names = "default";
+			compatible = "ns16550a";
+			reg = <0x10100000 0x20>;
+			interrupts = <6>;
+			clocks = <&ahb_clk>;
+			reg-io-width = <4>;
+			reg-shift = <2>;
+
+			status = "disabled";
+		};
+
+		i2c0: i2c@10100400 {
+			compatible = "mscc,ocelot-i2c", "snps,designware-i2c";
+			pinctrl-0 = <&i2c_pins>;
+			pinctrl-names = "default";
+			reg = <0x10100400 0x100>, <0x100002a4 0x8>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <11>;
+			clocks = <&ahb_clk>;
+
+			status = "disabled";
+		};
+
+		gpio: pinctrl@70068 {
+			compatible = "mscc,luton-pinctrl";
+			reg = <0x70068 0x28>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&gpio 0 0 32>;
+			interrupt-controller;
+			interrupts = <13>;
+			#interrupt-cells = <2>;
+
+			i2c_pins: i2c-pins {
+				pins = "GPIO_5", "GPIO_6";
+				function = "twi";
+			};
+
+			uart_pins: uart-pins {
+				pins = "GPIO_30", "GPIO_31";
+				function = "uart";
+			};
+
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/mscc/luton_pcb091.dts b/arch/mips/boot/dts/mscc/luton_pcb091.dts
new file mode 100644
index 000000000..26ef6285d
--- /dev/null
+++ b/arch/mips/boot/dts/mscc/luton_pcb091.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Microsemi Corporation
+ */
+
+/dts-v1/;
+
+#include "luton.dtsi"
+
+/ {
+	model = "Luton10 PCB091 Reference Board";
+	compatible = "mscc,luton-pcb091", "mscc,luton";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+	i2c-sda-hold-time-ns = <300>;
+};
diff --git a/arch/mips/boot/dts/mscc/ocelot.dtsi b/arch/mips/boot/dts/mscc/ocelot.dtsi
new file mode 100644
index 000000000..6bd8a1ad9
--- /dev/null
+++ b/arch/mips/boot/dts/mscc/ocelot.dtsi
@@ -0,0 +1,279 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/* Copyright (c) 2017 Microsemi Corporation */
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "mscc,ocelot";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "mips,mips24KEc";
+			device_type = "cpu";
+			clocks = <&cpu_clk>;
+			reg = <0>;
+		};
+	};
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	cpuintc: interrupt-controller {
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		compatible = "mti,cpu-interrupt-controller";
+	};
+
+	cpu_clk: cpu-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <500000000>;
+	};
+
+	ahb_clk: ahb-clk {
+		compatible = "fixed-factor-clock";
+		#clock-cells = <0>;
+		clocks = <&cpu_clk>;
+		clock-div = <2>;
+		clock-mult = <1>;
+	};
+
+	ahb@70000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x70000000 0x2000000>;
+
+		interrupt-parent = <&intc>;
+
+		cpu_ctrl: syscon@0 {
+			compatible = "mscc,ocelot-cpu-syscon", "syscon";
+			reg = <0x0 0x2c>;
+		};
+
+		intc: interrupt-controller@70 {
+			compatible = "mscc,ocelot-icpu-intr";
+			reg = <0x70 0x70>;
+			#interrupt-cells = <1>;
+			interrupt-controller;
+			interrupt-parent = <&cpuintc>;
+			interrupts = <2>;
+		};
+
+		uart0: serial@100000 {
+			pinctrl-0 = <&uart_pins>;
+			pinctrl-names = "default";
+			compatible = "ns16550a";
+			reg = <0x100000 0x20>;
+			interrupts = <6>;
+			clocks = <&ahb_clk>;
+			reg-io-width = <4>;
+			reg-shift = <2>;
+
+			status = "disabled";
+		};
+
+		i2c: i2c@100400 {
+			compatible = "mscc,ocelot-i2c", "snps,designware-i2c";
+			pinctrl-0 = <&i2c_pins>;
+			pinctrl-names = "default";
+			reg = <0x100400 0x100>, <0x198 0x8>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <8>;
+			clocks = <&ahb_clk>;
+
+			status = "disabled";
+		};
+
+		uart2: serial@100800 {
+			pinctrl-0 = <&uart2_pins>;
+			pinctrl-names = "default";
+			compatible = "ns16550a";
+			reg = <0x100800 0x20>;
+			interrupts = <7>;
+			clocks = <&ahb_clk>;
+			reg-io-width = <4>;
+			reg-shift = <2>;
+
+			status = "disabled";
+		};
+
+		spi: spi@101000 {
+			compatible = "mscc,ocelot-spi", "snps,dw-apb-ssi";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x101000 0x100>, <0x3c 0x18>;
+			interrupts = <9>;
+			clocks = <&ahb_clk>;
+
+			status = "disabled";
+		};
+
+		switch@1010000 {
+			compatible = "mscc,vsc7514-switch";
+			reg = <0x1010000 0x10000>,
+			      <0x1030000 0x10000>,
+			      <0x1080000 0x100>,
+			      <0x10e0000 0x10000>,
+			      <0x11e0000 0x100>,
+			      <0x11f0000 0x100>,
+			      <0x1200000 0x100>,
+			      <0x1210000 0x100>,
+			      <0x1220000 0x100>,
+			      <0x1230000 0x100>,
+			      <0x1240000 0x100>,
+			      <0x1250000 0x100>,
+			      <0x1260000 0x100>,
+			      <0x1270000 0x100>,
+			      <0x1280000 0x100>,
+			      <0x1800000 0x80000>,
+			      <0x1880000 0x10000>,
+			      <0x1040000 0x10000>,
+			      <0x1050000 0x10000>,
+			      <0x1060000 0x10000>,
+			      <0x1a0 0x1c4>;
+			reg-names = "sys", "rew", "qs", "ptp", "port0", "port1",
+				    "port2", "port3", "port4", "port5", "port6",
+				    "port7", "port8", "port9", "port10", "qsys",
+				    "ana", "s0", "s1", "s2", "fdma";
+			interrupts = <18 21 22 16>;
+			interrupt-names = "ptp_rdy", "xtr", "inj", "fdma";
+
+			ethernet-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port0: port@0 {
+					reg = <0>;
+					status = "disabled";
+				};
+				port1: port@1 {
+					reg = <1>;
+					status = "disabled";
+				};
+				port2: port@2 {
+					reg = <2>;
+					status = "disabled";
+				};
+				port3: port@3 {
+					reg = <3>;
+					status = "disabled";
+				};
+				port4: port@4 {
+					reg = <4>;
+					status = "disabled";
+				};
+				port5: port@5 {
+					reg = <5>;
+					status = "disabled";
+				};
+				port6: port@6 {
+					reg = <6>;
+					status = "disabled";
+				};
+				port7: port@7 {
+					reg = <7>;
+					status = "disabled";
+				};
+				port8: port@8 {
+					reg = <8>;
+					status = "disabled";
+				};
+				port9: port@9 {
+					reg = <9>;
+					status = "disabled";
+				};
+				port10: port@10 {
+					reg = <10>;
+					status = "disabled";
+				};
+			};
+		};
+
+		reset@1070008 {
+			compatible = "mscc,ocelot-chip-reset";
+			reg = <0x1070008 0x4>;
+		};
+
+		gpio: pinctrl@1070034 {
+			compatible = "mscc,ocelot-pinctrl";
+			reg = <0x1070034 0x68>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&gpio 0 0 22>;
+			interrupt-controller;
+			interrupts = <13>;
+			#interrupt-cells = <2>;
+
+			i2c_pins: i2c-pins {
+				pins = "GPIO_16", "GPIO_17";
+				function = "twi";
+			};
+
+			uart_pins: uart-pins {
+				pins = "GPIO_6", "GPIO_7";
+				function = "uart";
+			};
+
+			uart2_pins: uart2-pins {
+				pins = "GPIO_12", "GPIO_13";
+				function = "uart2";
+			};
+
+			miim1_pins: miim1-pins {
+				pins = "GPIO_14", "GPIO_15";
+				function = "miim";
+			};
+
+		};
+
+		mdio0: mdio@107009c {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "mscc,ocelot-miim";
+			reg = <0x107009c 0x24>, <0x10700f0 0x8>;
+			interrupts = <14>;
+			status = "disabled";
+
+			phy0: ethernet-phy@0 {
+				reg = <0>;
+			};
+			phy1: ethernet-phy@1 {
+				reg = <1>;
+			};
+			phy2: ethernet-phy@2 {
+				reg = <2>;
+			};
+			phy3: ethernet-phy@3 {
+				reg = <3>;
+			};
+		};
+
+		mdio1: mdio@10700c0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "mscc,ocelot-miim";
+			reg = <0x10700c0 0x24>;
+			interrupts = <15>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&miim1_pins>;
+			status = "disabled";
+		};
+
+		hsio: syscon@10d0000 {
+			compatible = "mscc,ocelot-hsio", "syscon", "simple-mfd";
+			reg = <0x10d0000 0x10000>;
+
+			serdes: serdes {
+				compatible = "mscc,vsc7514-serdes";
+				#phy-cells = <2>;
+			};
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/mscc/ocelot_pcb120.dts b/arch/mips/boot/dts/mscc/ocelot_pcb120.dts
new file mode 100644
index 000000000..d348742c2
--- /dev/null
+++ b/arch/mips/boot/dts/mscc/ocelot_pcb120.dts
@@ -0,0 +1,129 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/* Copyright (c) 2017 Microsemi Corporation */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/phy/phy-ocelot-serdes.h>
+#include "ocelot.dtsi"
+
+/ {
+	compatible = "mscc,ocelot-pcb120", "mscc,ocelot";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0e000000>;
+	};
+};
+
+&gpio {
+	phy_int_pins: phy-int-pins {
+		pins = "GPIO_4";
+		function = "gpio";
+	};
+
+	phy_load_save_pins: phy-load-save-pins {
+		pins = "GPIO_10";
+		function = "ptp2";
+	};
+};
+
+&mdio0 {
+	status = "okay";
+};
+
+&mdio1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&miim1_pins>, <&phy_int_pins>, <&phy_load_save_pins>;
+
+	phy7: ethernet-phy@0 {
+		reg = <0>;
+		interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-parent = <&gpio>;
+		load-save-gpios = <&gpio 10 GPIO_ACTIVE_HIGH>;
+	};
+	phy6: ethernet-phy@1 {
+		reg = <1>;
+		interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-parent = <&gpio>;
+		load-save-gpios = <&gpio 10 GPIO_ACTIVE_HIGH>;
+	};
+	phy5: ethernet-phy@2 {
+		reg = <2>;
+		interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-parent = <&gpio>;
+		load-save-gpios = <&gpio 10 GPIO_ACTIVE_HIGH>;
+	};
+	phy4: ethernet-phy@3 {
+		reg = <3>;
+		interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-parent = <&gpio>;
+		load-save-gpios = <&gpio 10 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&port0 {
+	status = "okay";
+	phy-handle = <&phy0>;
+	phy-mode = "internal";
+};
+
+&port1 {
+	status = "okay";
+	phy-handle = <&phy1>;
+	phy-mode = "internal";
+};
+
+&port2 {
+	status = "okay";
+	phy-handle = <&phy2>;
+	phy-mode = "internal";
+};
+
+&port3 {
+	status = "okay";
+	phy-handle = <&phy3>;
+	phy-mode = "internal";
+};
+
+&port4 {
+	status = "okay";
+	phy-handle = <&phy7>;
+	phy-mode = "sgmii";
+	phys = <&serdes 4 SERDES1G(2)>;
+};
+
+&port5 {
+	status = "okay";
+	phy-handle = <&phy4>;
+	phy-mode = "sgmii";
+	phys = <&serdes 5 SERDES1G(5)>;
+};
+
+&port6 {
+	status = "okay";
+	phy-handle = <&phy6>;
+	phy-mode = "sgmii";
+	phys = <&serdes 6 SERDES1G(3)>;
+};
+
+&port9 {
+	status = "okay";
+	phy-handle = <&phy5>;
+	phy-mode = "sgmii";
+	phys = <&serdes 9 SERDES1G(4)>;
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
diff --git a/arch/mips/boot/dts/mscc/ocelot_pcb123.dts b/arch/mips/boot/dts/mscc/ocelot_pcb123.dts
new file mode 100644
index 000000000..0185045c7
--- /dev/null
+++ b/arch/mips/boot/dts/mscc/ocelot_pcb123.dts
@@ -0,0 +1,71 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/* Copyright (c) 2017 Microsemi Corporation */
+
+/dts-v1/;
+
+#include "ocelot.dtsi"
+
+/ {
+	compatible = "mscc,ocelot-pcb123", "mscc,ocelot";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0e000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&spi {
+	status = "okay";
+
+	flash@0 {
+		compatible = "macronix,mx25l25635f", "jedec,spi-nor";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+	};
+};
+
+&i2c {
+	clock-frequency = <100000>;
+	i2c-sda-hold-time-ns = <300>;
+	status = "okay";
+};
+
+&mdio0 {
+	status = "okay";
+};
+
+&port0 {
+	status = "okay";
+	phy-handle = <&phy0>;
+	phy-mode = "internal";
+};
+
+&port1 {
+	status = "okay";
+	phy-handle = <&phy1>;
+	phy-mode = "internal";
+};
+
+&port2 {
+	status = "okay";
+	phy-handle = <&phy2>;
+	phy-mode = "internal";
+};
+
+&port3 {
+	status = "okay";
+	phy-handle = <&phy3>;
+	phy-mode = "internal";
+};
diff --git a/arch/mips/boot/dts/mscc/serval.dtsi b/arch/mips/boot/dts/mscc/serval.dtsi
new file mode 100644
index 000000000..089ce89df
--- /dev/null
+++ b/arch/mips/boot/dts/mscc/serval.dtsi
@@ -0,0 +1,153 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2018 Microsemi Corporation
+ */
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "mscc,serval";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "mips,mips24KEc";
+			device_type = "cpu";
+			clocks = <&cpu_clk>;
+			reg = <0>;
+		};
+	};
+
+	aliases {
+		serial0 = &uart0;
+		gpio0 = &gpio;
+	};
+
+	cpuintc: interrupt-controller {
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		compatible = "mti,cpu-interrupt-controller";
+	};
+
+	cpu_clk: cpu-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <416666666>;
+	};
+
+	ahb_clk: ahb-clk {
+		compatible = "fixed-factor-clock";
+		#clock-cells = <0>;
+		clocks = <&cpu_clk>;
+		clock-div = <2>;
+		clock-mult = <1>;
+	};
+
+	ahb: ahb {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		interrupt-parent = <&intc>;
+
+		cpu_ctrl: syscon@70000000 {
+			compatible = "mscc,ocelot-cpu-syscon", "syscon";
+			reg = <0x70000000 0x2c>;
+		};
+
+		intc: interrupt-controller@70000070 {
+			compatible = "mscc,serval-icpu-intr";
+			reg = <0x70000070 0x70>;
+			#interrupt-cells = <1>;
+			interrupt-controller;
+			interrupt-parent = <&cpuintc>;
+			interrupts = <2>;
+		};
+
+		uart0: serial@70100000 {
+			pinctrl-0 = <&uart_pins>;
+			pinctrl-names = "default";
+			compatible = "ns16550a";
+			reg = <0x70100000 0x20>;
+			interrupts = <6>;
+			clocks = <&ahb_clk>;
+			reg-io-width = <4>;
+			reg-shift = <2>;
+
+			status = "disabled";
+		};
+
+		uart2: serial@70100800 {
+			pinctrl-0 = <&uart2_pins>;
+			pinctrl-names = "default";
+			compatible = "ns16550a";
+			reg = <0x70100800 0x20>;
+			interrupts = <7>;
+			clocks = <&ahb_clk>;
+			reg-io-width = <4>;
+			reg-shift = <2>;
+
+			status = "disabled";
+		};
+
+		gpio: pinctrl@71070034 {
+			compatible = "mscc,serval-pinctrl";
+			reg = <0x71070034 0x28>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&gpio 0 0 22>;
+
+			sgpio_pins: sgpio-pins {
+				pins = "GPIO_0", "GPIO_2", "GPIO_3", "GPIO_1";
+				function = "sg0";
+			};
+
+			i2c_pins: i2c-pins {
+				pins = "GPIO_6", "GPIO_7";
+				function = "twi";
+			};
+
+			uart_pins: uart-pins {
+				pins = "GPIO_26", "GPIO_27";
+				function = "uart";
+			};
+
+			uart2_pins: uart2-pins {
+				pins = "GPIO_13", "GPIO_14";
+				function = "uart2";
+			};
+
+			cs1_pins: cs1-pins {
+				pins = "GPIO_8";
+				function = "si";
+			};
+
+			irqext0_pins: irqext0-pins {
+				pins = "GPIO_28";
+				function = "irq0";
+			};
+
+			irqext1_pins: irqext1-pins {
+				pins = "GPIO_29";
+				function = "irq1";
+			};
+		};
+
+		i2c0: i2c@70100400 {
+			compatible = "mscc,ocelot-i2c", "snps,designware-i2c";
+			status = "disabled";
+			pinctrl-0 = <&i2c_pins>;
+			pinctrl-names = "default";
+			reg = <0x70100400 0x100>, <0x70000190 0x8>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <8>;
+			clock-frequency = <100000>;
+			clocks = <&ahb_clk>;
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/mscc/serval_common.dtsi b/arch/mips/boot/dts/mscc/serval_common.dtsi
new file mode 100644
index 000000000..0893de420
--- /dev/null
+++ b/arch/mips/boot/dts/mscc/serval_common.dtsi
@@ -0,0 +1,127 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Microsemi Corporation
+ */
+
+#include "serval.dtsi"
+
+/ {
+	aliases {
+		serial0 = &uart0;
+		i2c104  = &i2c104;
+		i2c105  = &i2c105;
+		i2c106  = &i2c106;
+		i2c107  = &i2c107;
+		i2c108  = &i2c108;
+		i2c109  = &i2c109;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	i2c0_imux: i2c0-imux{
+		compatible = "i2c-mux-pinctrl";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-parent = <&i2c0>;
+		pinctrl-names =
+		"i2c104", "i2c105", "i2c106", "i2c107",
+		"i2c108", "i2c109", "idle";
+		pinctrl-0 = <&i2cmux_0>;
+		pinctrl-1 = <&i2cmux_1>;
+		pinctrl-2 = <&i2cmux_2>;
+		pinctrl-3 = <&i2cmux_3>;
+		pinctrl-4 = <&i2cmux_4>;
+		pinctrl-5 = <&i2cmux_5>;
+		pinctrl-6 = <&i2cmux_pins_i>;
+		i2c104: i2c_sfp0@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c105: i2c_sfp1@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c106: i2c_sfp2@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c107: i2c_sfp3@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c108: i2c_sfp4@4 {
+			reg = <4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c109: i2c_sfp5@5 {
+			reg = <5>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+};
+
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&gpio {
+	i2c_pins: i2c-pins {
+		pins = "GPIO_7"; /* No "default" scl for i2c0 */
+		function = "twi";
+	};
+	i2cmux_pins_i: i2cmux-pins {
+		pins = "GPIO_11", "GPIO_12", "GPIO_18", "GPIO_19",
+			"GPIO_20", "GPIO_21";
+		function = "twi_scl_m";
+		output-low;
+	};
+	i2cmux_0: i2cmux-0-pins {
+		pins = "GPIO_11";
+		function = "twi_scl_m";
+		output-high;
+	};
+	i2cmux_1: i2cmux-1-pins {
+		pins = "GPIO_12";
+		function = "twi_scl_m";
+		output-high;
+	};
+	i2cmux_2: i2cmux-2-pins {
+		pins = "GPIO_18";
+		function = "twi_scl_m";
+		output-high;
+	};
+	i2cmux_3: i2cmux-3-pins {
+		pins = "GPIO_19";
+		function = "twi_scl_m";
+		output-high;
+	};
+	i2cmux_4: i2cmux-4-pins {
+		pins = "GPIO_20";
+		function = "twi_scl_m";
+		output-high;
+	};
+	i2cmux_5: i2cmux-5-pins {
+		pins = "GPIO_21";
+		function = "twi_scl_m";
+		output-high;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+	i2c-sda-hold-time-ns = <300>;
+};
+
diff --git a/arch/mips/boot/dts/mscc/serval_pcb105.dts b/arch/mips/boot/dts/mscc/serval_pcb105.dts
new file mode 100644
index 000000000..a1b0012b7
--- /dev/null
+++ b/arch/mips/boot/dts/mscc/serval_pcb105.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2018 Microsemi Corporation
+ */
+
+/dts-v1/;
+#include "serval_common.dtsi"
+
+/ {
+	model = "Serval PCB105 Reference Board";
+	compatible = "mscc,serval-pcb105", "mscc,serval";
+
+	aliases {
+	};
+
+};
+
diff --git a/arch/mips/boot/dts/mscc/serval_pcb106.dts b/arch/mips/boot/dts/mscc/serval_pcb106.dts
new file mode 100644
index 000000000..237be7c8d
--- /dev/null
+++ b/arch/mips/boot/dts/mscc/serval_pcb106.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2018 Microsemi Corporation
+ */
+
+/dts-v1/;
+#include "serval_common.dtsi"
+
+/ {
+	model = "Serval PCB106 Reference Board";
+	compatible = "mscc,serval-pcb106", "mscc,serval";
+
+	aliases {
+	};
+
+};
+
diff --git a/arch/mips/boot/dts/mti/Makefile b/arch/mips/boot/dts/mti/Makefile
new file mode 100644
index 000000000..b5f742699
--- /dev/null
+++ b/arch/mips/boot/dts/mti/Makefile
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_MIPS_MALTA)	+= malta.dtb
+dtb-$(CONFIG_LEGACY_BOARD_SEAD3)	+= sead3.dtb
+
+obj-$(CONFIG_BUILTIN_DTB)	+= $(addsuffix .o, $(dtb-y))
diff --git a/arch/mips/boot/dts/mti/malta.dts b/arch/mips/boot/dts/mti/malta.dts
new file mode 100644
index 000000000..f03279b1c
--- /dev/null
+++ b/arch/mips/boot/dts/mti/malta.dts
@@ -0,0 +1,117 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/mips-gic.h>
+
+/memreserve/ 0x00000000 0x00001000;	/* YAMON exception vectors */
+/memreserve/ 0x00001000 0x000ef000;	/* YAMON */
+/memreserve/ 0x000f0000 0x00010000;	/* PIIX4 ISA memory */
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "mti,malta";
+
+	cpu_intc: interrupt-controller {
+		compatible = "mti,cpu-interrupt-controller";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+
+	gic: interrupt-controller@1bdc0000 {
+		compatible = "mti,gic";
+		reg = <0x1bdc0000 0x20000>;
+
+		interrupt-controller;
+		#interrupt-cells = <3>;
+
+		/*
+		 * Declare the interrupt-parent even though the mti,gic
+		 * binding doesn't require it, such that the kernel can
+		 * figure out that cpu_intc is the root interrupt
+		 * controller & should be probed first.
+		 */
+		interrupt-parent = <&cpu_intc>;
+
+		timer {
+			compatible = "mti,gic-timer";
+			interrupts = <GIC_LOCAL 1 IRQ_TYPE_NONE>;
+		};
+	};
+
+	i8259: interrupt-controller@20 {
+		compatible = "intel,i8259";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SHARED 3 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	flash@1e000000 {
+		compatible = "intel,dt28f160", "cfi-flash";
+		reg = <0x1e000000 0x400000>;
+		bank-width = <4>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			yamon@0 {
+				label = "YAMON";
+				reg = <0x0 0x100000>;
+				read-only;
+			};
+
+			user-fs@100000 {
+				label = "User FS";
+				reg = <0x100000 0x2e0000>;
+			};
+
+			board-config@3e0000 {
+				label = "Board Config";
+				reg = <0x3e0000 0x20000>;
+				read-only;
+			};
+		};
+	};
+
+	fpga_regs: system-controller@1f000000 {
+		compatible = "mti,malta-fpga", "syscon", "simple-mfd";
+		reg = <0x1f000000 0x1000>;
+		native-endian;
+
+		lcd@410 {
+			compatible = "mti,malta-lcd";
+			offset = <0x410>;
+		};
+
+		reboot {
+			compatible = "syscon-reboot";
+			regmap = <&fpga_regs>;
+			offset = <0x500>;
+			mask = <0x42>;
+		};
+	};
+
+	isa {
+		compatible = "isa";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges = <1 0 0 0x1000>;
+
+		rtc@70 {
+			compatible = "motorola,mc146818";
+			reg = <1 0x70 0x8>;
+
+			interrupt-parent = <&i8259>;
+			interrupts = <8>;
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/mti/sead3.dts b/arch/mips/boot/dts/mti/sead3.dts
new file mode 100644
index 000000000..046c97a29
--- /dev/null
+++ b/arch/mips/boot/dts/mti/sead3.dts
@@ -0,0 +1,259 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+/memreserve/ 0x00000000 0x00001000;	// reserved
+/memreserve/ 0x00001000 0x000ef000;	// ROM data
+/memreserve/ 0x000f0000 0x004cc000;	// reserved
+
+#include <dt-bindings/interrupt-controller/mips-gic.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "mti,sead-3";
+	model = "MIPS SEAD-3";
+
+	chosen {
+		stdout-path = "serial1:115200";
+	};
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+	};
+
+	cpus {
+		cpu@0 {
+			compatible = "mti,mips14KEc", "mti,mips14Kc";
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+
+	cpu_intc: interrupt-controller {
+		compatible = "mti,cpu-interrupt-controller";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+
+	gic: interrupt-controller@1b1c0000 {
+		compatible = "mti,gic";
+		reg = <0x1b1c0000 0x20000>;
+
+		interrupt-controller;
+		#interrupt-cells = <3>;
+
+		/*
+		 * Declare the interrupt-parent even though the mti,gic
+		 * binding doesn't require it, such that the kernel can
+		 * figure out that cpu_intc is the root interrupt
+		 * controller & should be probed first.
+		 */
+		interrupt-parent = <&cpu_intc>;
+	};
+
+	usb@1b200000 {
+		compatible = "generic-ehci";
+		reg = <0x1b200000 0x1000>;
+
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SHARED 0 IRQ_TYPE_LEVEL_HIGH>; /* GIC 0 or CPU 6 */
+
+		has-transaction-translator;
+	};
+
+	flash@1c000000 {
+		compatible = "intel,28f128j3", "cfi-flash";
+		reg = <0x1c000000 0x2000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		bank-width = <4>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			user-fs@0 {
+				label = "User FS";
+				reg = <0x0 0x1fc0000>;
+			};
+
+			board-config@3e0000 {
+				label = "Board Config";
+				reg = <0x1fc0000 0x40000>;
+			};
+		};
+	};
+
+	fpga_regs: system-controller@1f000000 {
+		compatible = "mti,sead3-fpga", "syscon", "simple-mfd";
+		reg = <0x1f000000 0x200>;
+
+		reboot {
+			compatible = "syscon-reboot";
+			regmap = <&fpga_regs>;
+			offset = <0x50>;
+			mask = <0x4d>;
+		};
+
+		poweroff {
+			compatible = "restart-poweroff";
+		};
+	};
+
+	system-controller@1f000200 {
+		compatible = "mti,sead3-cpld", "syscon", "simple-mfd";
+		reg = <0x1f000200 0x300>;
+
+		led@10.0 {
+			compatible = "register-bit-led";
+			offset = <0x10>;
+			mask = <0x1>;
+			label = "pled0";
+		};
+		led@10.1 {
+			compatible = "register-bit-led";
+			offset = <0x10>;
+			mask = <0x2>;
+			label = "pled1";
+		};
+		led@10.2 {
+			compatible = "register-bit-led";
+			offset = <0x10>;
+			mask = <0x4>;
+			label = "pled2";
+		};
+		led@10.3 {
+			compatible = "register-bit-led";
+			offset = <0x10>;
+			mask = <0x8>;
+			label = "pled3";
+		};
+		led@10.4 {
+			compatible = "register-bit-led";
+			offset = <0x10>;
+			mask = <0x10>;
+			label = "pled4";
+		};
+		led@10.5 {
+			compatible = "register-bit-led";
+			offset = <0x10>;
+			mask = <0x20>;
+			label = "pled5";
+		};
+		led@10.6 {
+			compatible = "register-bit-led";
+			offset = <0x10>;
+			mask = <0x40>;
+			label = "pled6";
+		};
+		led@10.7 {
+			compatible = "register-bit-led";
+			offset = <0x10>;
+			mask = <0x80>;
+			label = "pled7";
+		};
+
+		led@18.0 {
+			compatible = "register-bit-led";
+			offset = <0x18>;
+			mask = <0x1>;
+			label = "fled0";
+		};
+		led@18.1 {
+			compatible = "register-bit-led";
+			offset = <0x18>;
+			mask = <0x2>;
+			label = "fled1";
+		};
+		led@18.2 {
+			compatible = "register-bit-led";
+			offset = <0x18>;
+			mask = <0x4>;
+			label = "fled2";
+		};
+		led@18.3 {
+			compatible = "register-bit-led";
+			offset = <0x18>;
+			mask = <0x8>;
+			label = "fled3";
+		};
+		led@18.4 {
+			compatible = "register-bit-led";
+			offset = <0x18>;
+			mask = <0x10>;
+			label = "fled4";
+		};
+		led@18.5 {
+			compatible = "register-bit-led";
+			offset = <0x18>;
+			mask = <0x20>;
+			label = "fled5";
+		};
+		led@18.6 {
+			compatible = "register-bit-led";
+			offset = <0x18>;
+			mask = <0x40>;
+			label = "fled6";
+		};
+		led@18.7 {
+			compatible = "register-bit-led";
+			offset = <0x18>;
+			mask = <0x80>;
+			label = "fled7";
+		};
+
+		lcd@200 {
+			compatible = "mti,sead3-lcd";
+			offset = <0x200>;
+		};
+	};
+
+	/* UART connected to FTDI & miniUSB socket */
+	uart0: uart@1f000900 {
+		compatible = "ns16550a";
+		reg = <0x1f000900 0x20>;
+		reg-io-width = <4>;
+		reg-shift = <2>;
+
+		clock-frequency = <14745600>;
+
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SHARED 3 IRQ_TYPE_LEVEL_HIGH>; /* GIC 3 or CPU 4 */
+
+		no-loopback-test;
+	};
+
+	/* UART connected to RS232 socket */
+	uart1: uart@1f000800 {
+		compatible = "ns16550a";
+		reg = <0x1f000800 0x20>;
+		reg-io-width = <4>;
+		reg-shift = <2>;
+
+		clock-frequency = <14745600>;
+
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SHARED 2 IRQ_TYPE_LEVEL_HIGH>; /* GIC 2 or CPU 4 */
+
+		no-loopback-test;
+	};
+
+	ethernet@1f010000 {
+		compatible = "smsc,lan9115";
+		reg = <0x1f010000 0x10000>;
+		reg-io-width = <4>;
+
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SHARED 0 IRQ_TYPE_LEVEL_HIGH>; /* GIC 0 or CPU 6 */
+
+		phy-mode = "mii";
+		smsc,irq-push-pull;
+		smsc,save-mac-address;
+	};
+};
diff --git a/arch/mips/boot/dts/ni/169445.dts b/arch/mips/boot/dts/ni/169445.dts
new file mode 100644
index 000000000..5389ef46c
--- /dev/null
+++ b/arch/mips/boot/dts/ni/169445.dts
@@ -0,0 +1,100 @@
+/dts-v1/;
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "ni,169445";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "mti,mips14KEc";
+			clocks = <&baseclk>;
+			reg = <0>;
+		};
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x10000000>;
+	};
+
+	baseclk: baseclock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+	};
+
+	cpu_intc: interrupt-controller {
+		#address-cells = <0>;
+		compatible = "mti,cpu-interrupt-controller";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+
+	ahb@1f300000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x1f300000 0x80FFF>;
+
+		gpio1: gpio@10 {
+			compatible = "ni,169445-nand-gpio";
+			reg = <0x10 0x4>;
+			reg-names = "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		gpio2: gpio@14 {
+			compatible = "ni,169445-nand-gpio";
+			reg = <0x14 0x4>;
+			reg-names = "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			no-output;
+		};
+
+		nand@0 {
+			compatible = "gpio-control-nand";
+			nand-on-flash-bbt;
+			nand-ecc-mode = "soft_bch";
+			nand-ecc-step-size = <512>;
+			nand-ecc-strength = <4>;
+			reg = <0x0 4>;
+			gpios = <&gpio2 0 0>, /* rdy */
+				<&gpio1 1 0>, /* nce */
+				<&gpio1 2 0>, /* ale */
+				<&gpio1 3 0>, /* cle */
+				<&gpio1 4 0>; /* nwp */
+		};
+
+		serial@80000 {
+			compatible = "ns16550a";
+			reg = <0x80000 0x1000>;
+			interrupt-parent = <&cpu_intc>;
+			interrupts = <6>;
+			clocks = <&baseclk>;
+			reg-shift = <0>;
+		};
+
+		ethernet@40000 {
+			compatible = "snps,dwmac-4.10a";
+			interrupt-parent = <&cpu_intc>;
+			interrupts = <5>;
+			interrupt-names = "macirq";
+			reg = <0x40000 0x2000>;
+			clock-names = "stmmaceth", "pclk";
+			clocks = <&baseclk>, <&baseclk>;
+
+			phy-mode = "rgmii";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/ni/Makefile b/arch/mips/boot/dts/ni/Makefile
new file mode 100644
index 000000000..93867e1a5
--- /dev/null
+++ b/arch/mips/boot/dts/ni/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0-only
+dtb-$(CONFIG_FIT_IMAGE_FDT_NI169445)	+= 169445.dtb
diff --git a/arch/mips/boot/dts/pic32/Makefile b/arch/mips/boot/dts/pic32/Makefile
new file mode 100644
index 000000000..fb57f3632
--- /dev/null
+++ b/arch/mips/boot/dts/pic32/Makefile
@@ -0,0 +1,7 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_DTB_PIC32_MZDA_SK)		+= pic32mzda_sk.dtb
+
+dtb-$(CONFIG_DTB_PIC32_NONE)		+= \
+					pic32mzda_sk.dtb
+
+obj-$(CONFIG_BUILTIN_DTB)	+= $(addsuffix .o, $(dtb-y))
diff --git a/arch/mips/boot/dts/pic32/pic32mzda.dtsi b/arch/mips/boot/dts/pic32/pic32mzda.dtsi
new file mode 100644
index 000000000..f1e3dad6b
--- /dev/null
+++ b/arch/mips/boot/dts/pic32/pic32mzda.dtsi
@@ -0,0 +1,298 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2015 Microchip Technology Inc.  All rights reserved.
+ */
+#include <dt-bindings/clock/microchip,pic32-clock.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	interrupt-parent = <&evic>;
+
+	aliases {
+		gpio0 = &gpio0;
+		gpio1 = &gpio1;
+		gpio2 = &gpio2;
+		gpio3 = &gpio3;
+		gpio4 = &gpio4;
+		gpio5 = &gpio5;
+		gpio6 = &gpio6;
+		gpio7 = &gpio7;
+		gpio8 = &gpio8;
+		gpio9 = &gpio9;
+		serial0 = &uart1;
+		serial1 = &uart2;
+		serial2 = &uart3;
+		serial3 = &uart4;
+		serial4 = &uart5;
+		serial5 = &uart6;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "mti,mips14KEc";
+			device_type = "cpu";
+		};
+	};
+
+	soc {
+		compatible = "microchip,pic32mzda-infra";
+		interrupts = <0 IRQ_TYPE_EDGE_RISING>;
+	};
+
+	/* external clock input on TxCLKI pin */
+	txcki: txcki_clk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <4000000>;
+		status = "disabled";
+	};
+
+	/* external input on REFCLKIx pin */
+	refix: refix_clk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+		status = "disabled";
+	};
+
+	rootclk: clock-controller@1f801200 {
+		compatible = "microchip,pic32mzda-clk";
+		reg = <0x1f801200 0x200>;
+		#clock-cells = <1>;
+		microchip,pic32mzda-sosc;
+	};
+
+	evic: interrupt-controller@1f810000 {
+		compatible = "microchip,pic32mzda-evic";
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		reg = <0x1f810000 0x1000>;
+		microchip,external-irqs = <3 8 13 18 23>;
+	};
+
+	pic32_pinctrl: pinctrl@1f801400{
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "microchip,pic32mzda-pinctrl";
+		reg = <0x1f801400 0x400>;
+		clocks = <&rootclk PB1CLK>;
+	};
+
+	/* PORTA */
+	gpio0: gpio0@1f860000 {
+		compatible = "microchip,pic32mzda-gpio";
+		reg = <0x1f860000 0x100>;
+		interrupts = <118 IRQ_TYPE_LEVEL_HIGH>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		clocks = <&rootclk PB4CLK>;
+		microchip,gpio-bank = <0>;
+		gpio-ranges = <&pic32_pinctrl 0 0 16>;
+	};
+
+	/* PORTB */
+	gpio1: gpio1@1f860100 {
+		compatible = "microchip,pic32mzda-gpio";
+		reg = <0x1f860100 0x100>;
+		interrupts = <119 IRQ_TYPE_LEVEL_HIGH>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		clocks = <&rootclk PB4CLK>;
+		microchip,gpio-bank = <1>;
+		gpio-ranges = <&pic32_pinctrl 0 16 16>;
+	};
+
+	/* PORTC */
+	gpio2: gpio2@1f860200 {
+		compatible = "microchip,pic32mzda-gpio";
+		reg = <0x1f860200 0x100>;
+		interrupts = <120 IRQ_TYPE_LEVEL_HIGH>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		clocks = <&rootclk PB4CLK>;
+		microchip,gpio-bank = <2>;
+		gpio-ranges = <&pic32_pinctrl 0 32 16>;
+	};
+
+	/* PORTD */
+	gpio3: gpio3@1f860300 {
+		compatible = "microchip,pic32mzda-gpio";
+		reg = <0x1f860300 0x100>;
+		interrupts = <121 IRQ_TYPE_LEVEL_HIGH>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		clocks = <&rootclk PB4CLK>;
+		microchip,gpio-bank = <3>;
+		gpio-ranges = <&pic32_pinctrl 0 48 16>;
+	};
+
+	/* PORTE */
+	gpio4: gpio4@1f860400 {
+		compatible = "microchip,pic32mzda-gpio";
+		reg = <0x1f860400 0x100>;
+		interrupts = <122 IRQ_TYPE_LEVEL_HIGH>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		clocks = <&rootclk PB4CLK>;
+		microchip,gpio-bank = <4>;
+		gpio-ranges = <&pic32_pinctrl 0 64 16>;
+	};
+
+	/* PORTF */
+	gpio5: gpio5@1f860500 {
+		compatible = "microchip,pic32mzda-gpio";
+		reg = <0x1f860500 0x100>;
+		interrupts = <123 IRQ_TYPE_LEVEL_HIGH>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		clocks = <&rootclk PB4CLK>;
+		microchip,gpio-bank = <5>;
+		gpio-ranges = <&pic32_pinctrl 0 80 16>;
+	};
+
+	/* PORTG */
+	gpio6: gpio6@1f860600 {
+		compatible = "microchip,pic32mzda-gpio";
+		reg = <0x1f860600 0x100>;
+		interrupts = <124 IRQ_TYPE_LEVEL_HIGH>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		clocks = <&rootclk PB4CLK>;
+		microchip,gpio-bank = <6>;
+		gpio-ranges = <&pic32_pinctrl 0 96 16>;
+	};
+
+	/* PORTH */
+	gpio7: gpio7@1f860700 {
+		compatible = "microchip,pic32mzda-gpio";
+		reg = <0x1f860700 0x100>;
+		interrupts = <125 IRQ_TYPE_LEVEL_HIGH>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		clocks = <&rootclk PB4CLK>;
+		microchip,gpio-bank = <7>;
+		gpio-ranges = <&pic32_pinctrl 0 112 16>;
+	};
+
+	/* PORTI does not exist */
+
+	/* PORTJ */
+	gpio8: gpio8@1f860800 {
+		compatible = "microchip,pic32mzda-gpio";
+		reg = <0x1f860800 0x100>;
+		interrupts = <126 IRQ_TYPE_LEVEL_HIGH>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		clocks = <&rootclk PB4CLK>;
+		microchip,gpio-bank = <8>;
+		gpio-ranges = <&pic32_pinctrl 0 128 16>;
+	};
+
+	/* PORTK */
+	gpio9: gpio9@1f860900 {
+		compatible = "microchip,pic32mzda-gpio";
+		reg = <0x1f860900 0x100>;
+		interrupts = <127 IRQ_TYPE_LEVEL_HIGH>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		clocks = <&rootclk PB4CLK>;
+		microchip,gpio-bank = <9>;
+		gpio-ranges = <&pic32_pinctrl 0 144 16>;
+	};
+
+	sdhci: sdhci@1f8ec000 {
+		compatible = "microchip,pic32mzda-sdhci";
+		reg = <0x1f8ec000 0x100>;
+		interrupts = <191 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&rootclk REF4CLK>, <&rootclk PB5CLK>;
+		clock-names = "base_clk", "sys_clk";
+		bus-width = <4>;
+		cap-sd-highspeed;
+		status = "disabled";
+	};
+
+	uart1: serial@1f822000 {
+		compatible = "microchip,pic32mzda-uart";
+		reg = <0x1f822000 0x50>;
+		interrupts = <112 IRQ_TYPE_LEVEL_HIGH>,
+			<113 IRQ_TYPE_LEVEL_HIGH>,
+			<114 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&rootclk PB2CLK>;
+		status = "disabled";
+	};
+
+	uart2: serial@1f822200 {
+		compatible = "microchip,pic32mzda-uart";
+		reg = <0x1f822200 0x50>;
+		interrupts = <145 IRQ_TYPE_LEVEL_HIGH>,
+			<146 IRQ_TYPE_LEVEL_HIGH>,
+			<147 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&rootclk PB2CLK>;
+		status = "disabled";
+	};
+
+	uart3: serial@1f822400 {
+		compatible = "microchip,pic32mzda-uart";
+		reg = <0x1f822400 0x50>;
+		interrupts = <157 IRQ_TYPE_LEVEL_HIGH>,
+			<158 IRQ_TYPE_LEVEL_HIGH>,
+			<159 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&rootclk PB2CLK>;
+		status = "disabled";
+	};
+
+	uart4: serial@1f822600 {
+		compatible = "microchip,pic32mzda-uart";
+		reg = <0x1f822600 0x50>;
+		interrupts = <170 IRQ_TYPE_LEVEL_HIGH>,
+			<171 IRQ_TYPE_LEVEL_HIGH>,
+			<172 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&rootclk PB2CLK>;
+		status = "disabled";
+	};
+
+	uart5: serial@1f822800 {
+		compatible = "microchip,pic32mzda-uart";
+		reg = <0x1f822800 0x50>;
+		interrupts = <179 IRQ_TYPE_LEVEL_HIGH>,
+			<180 IRQ_TYPE_LEVEL_HIGH>,
+			<181 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&rootclk PB2CLK>;
+		status = "disabled";
+	};
+
+	uart6: serial@1f822A00 {
+		compatible = "microchip,pic32mzda-uart";
+		reg = <0x1f822A00 0x50>;
+		interrupts = <188 IRQ_TYPE_LEVEL_HIGH>,
+			<189 IRQ_TYPE_LEVEL_HIGH>,
+			<190 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&rootclk PB2CLK>;
+		status = "disabled";
+	};
+};
diff --git a/arch/mips/boot/dts/pic32/pic32mzda_sk.dts b/arch/mips/boot/dts/pic32/pic32mzda_sk.dts
new file mode 100644
index 000000000..ab70637bb
--- /dev/null
+++ b/arch/mips/boot/dts/pic32/pic32mzda_sk.dts
@@ -0,0 +1,145 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2015 Microchip Technology Inc.  All rights reserved.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+#include "pic32mzda.dtsi"
+
+/ {
+	compatible = "microchip,pic32mzda-sk", "microchip,pic32mzda";
+	model = "Microchip PIC32MZDA Starter Kit";
+
+	memory {
+		device_type = "memory";
+		reg = <0x08000000 0x08000000>;
+	};
+
+	chosen {
+		bootargs = "earlyprintk=ttyPIC1,115200n8r console=ttyPIC1,115200n8";
+	};
+
+	leds0 {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&user_leds_s0>;
+
+		led@1 {
+			label = "pic32mzda_sk:red:led1";
+			gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led@2 {
+			label = "pic32mzda_sk:yellow:led2";
+			gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+		};
+
+		led@3 {
+			label = "pic32mzda_sk:green:led3";
+			gpios = <&gpio7 2 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+	keys0 {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&user_buttons_s0>;
+		pinctrl-names = "default";
+
+		button-1 {
+			label = "ESC";
+			linux,code = <1>;
+			gpios = <&gpio1 12 0>;
+		};
+
+		button-2 {
+			label = "Home";
+			linux,code = <102>;
+			gpios = <&gpio1 13 0>;
+		};
+
+		button-3 {
+			label = "Menu";
+			linux,code = <139>;
+			gpios = <&gpio1 14 0>;
+		};
+	};
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&sdhci {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdhc1>;
+	status = "okay";
+	assigned-clocks = <&rootclk REF2CLK>, <&rootclk REF4CLK>,
+		<&rootclk REF5CLK>;
+	assigned-clock-rates = <50000000>, <25000000>, <40000000>;
+};
+
+&pic32_pinctrl {
+
+	pinctrl_sdhc1: sdhc1_pins0 {
+		pins = "A6", "D4", "G13", "G12", "G14", "A7", "A0";
+		microchip,digital;
+	};
+
+	user_leds_s0: user_leds_s0 {
+		pins = "H0", "H1", "H2";
+		output-low;
+		microchip,digital;
+	};
+
+	user_buttons_s0: user_buttons_s0 {
+		pins = "B12", "B13", "B14";
+		microchip,digital;
+		input-enable;
+		bias-pull-up;
+	};
+
+	pinctrl_uart2: pinctrl_uart2 {
+		uart2-tx {
+			pins = "G9";
+			function = "U2TX";
+			microchip,digital;
+			output-high;
+		};
+		uart2-rx {
+			pins = "B0";
+			function = "U2RX";
+			microchip,digital;
+			input-enable;
+		};
+	};
+
+	pinctrl_uart4: uart4-0 {
+		uart4-tx {
+			pins = "C3";
+			function = "U4TX";
+			microchip,digital;
+			output-high;
+		};
+		uart4-rx {
+			pins = "E8";
+			function = "U4RX";
+			microchip,digital;
+			input-enable;
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/qca/Makefile b/arch/mips/boot/dts/qca/Makefile
new file mode 100644
index 000000000..6749f7706
--- /dev/null
+++ b/arch/mips/boot/dts/qca/Makefile
@@ -0,0 +1,8 @@
+# SPDX-License-Identifier: GPL-2.0
+# All DTBs
+dtb-$(CONFIG_ATH79)			+= ar9132_tl_wr1043nd_v1.dtb
+dtb-$(CONFIG_ATH79)			+= ar9331_dpt_module.dtb
+dtb-$(CONFIG_ATH79)			+= ar9331_dragino_ms14.dtb
+dtb-$(CONFIG_ATH79)			+= ar9331_omega.dtb
+dtb-$(CONFIG_ATH79)			+= ar9331_openembed_som9331_board.dtb
+dtb-$(CONFIG_ATH79)			+= ar9331_tl_mr3020.dtb
diff --git a/arch/mips/boot/dts/qca/ar9132.dtsi b/arch/mips/boot/dts/qca/ar9132.dtsi
new file mode 100644
index 000000000..61dcfa5b6
--- /dev/null
+++ b/arch/mips/boot/dts/qca/ar9132.dtsi
@@ -0,0 +1,171 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/clock/ath79-clk.h>
+
+/ {
+	compatible = "qca,ar9132";
+
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "mips,mips24Kc";
+			clocks = <&pll ATH79_CLK_CPU>;
+			reg = <0>;
+		};
+	};
+
+	cpuintc: interrupt-controller {
+		compatible = "qca,ar9132-cpu-intc", "qca,ar7100-cpu-intc";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		qca,ddr-wb-channel-interrupts = <2>, <3>, <4>, <5>;
+		qca,ddr-wb-channels = <&ddr_ctrl 3>, <&ddr_ctrl 2>,
+					<&ddr_ctrl 0>, <&ddr_ctrl 1>;
+	};
+
+	ahb {
+		compatible = "simple-bus";
+		ranges;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		interrupt-parent = <&cpuintc>;
+
+		apb {
+			compatible = "simple-bus";
+			ranges;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			interrupt-parent = <&miscintc>;
+
+			ddr_ctrl: memory-controller@18000000 {
+				compatible = "qca,ar9132-ddr-controller",
+						"qca,ar7240-ddr-controller";
+				reg = <0x18000000 0x100>;
+
+				#qca,ddr-wb-channel-cells = <1>;
+			};
+
+			uart: uart@18020000 {
+				compatible = "ns8250";
+				reg = <0x18020000 0x20>;
+				interrupts = <3>;
+
+				clocks = <&pll ATH79_CLK_AHB>;
+				clock-names = "uart";
+
+				reg-io-width = <4>;
+				reg-shift = <2>;
+				no-loopback-test;
+
+				status = "disabled";
+			};
+
+			gpio: gpio@18040000 {
+				compatible = "qca,ar9132-gpio",
+						"qca,ar7100-gpio";
+				reg = <0x18040000 0x30>;
+				interrupts = <2>;
+
+				ngpios = <22>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
+
+			pll: pll-controller@18050000 {
+				compatible = "qca,ar9132-pll",
+						"qca,ar9130-pll";
+				reg = <0x18050000 0x20>;
+
+				clock-names = "ref";
+				/* The board must provides the ref clock */
+
+				#clock-cells = <1>;
+				clock-output-names = "cpu", "ddr", "ahb";
+			};
+
+			wdt: wdt@18060008 {
+				compatible = "qca,ar7130-wdt";
+				reg = <0x18060008 0x8>;
+
+				interrupts = <4>;
+
+				clocks = <&pll ATH79_CLK_AHB>;
+				clock-names = "wdt";
+			};
+
+			miscintc: interrupt-controller@18060010 {
+				compatible = "qca,ar9132-misc-intc",
+					   "qca,ar7100-misc-intc";
+				reg = <0x18060010 0x8>;
+
+				interrupt-parent = <&cpuintc>;
+				interrupts = <6>;
+
+				interrupt-controller;
+				#interrupt-cells = <1>;
+			};
+
+			rst: reset-controller@1806001c {
+				compatible = "qca,ar9132-reset",
+						"qca,ar7100-reset";
+				reg = <0x1806001c 0x4>;
+
+				#reset-cells = <1>;
+			};
+		};
+
+		usb: usb@1b000100 {
+			compatible = "qca,ar7100-ehci", "generic-ehci";
+			reg = <0x1b000100 0x100>;
+
+			interrupts = <3>;
+			resets = <&rst 5>;
+
+			has-transaction-translator;
+
+			phy-names = "usb";
+			phys = <&usb_phy>;
+
+			status = "disabled";
+		};
+
+		spi: spi@1f000000 {
+			compatible = "qca,ar9132-spi", "qca,ar7100-spi";
+			reg = <0x1f000000 0x10>;
+
+			clocks = <&pll ATH79_CLK_AHB>;
+			clock-names = "ahb";
+
+			status = "disabled";
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
+	usb_phy: usb-phy {
+		compatible = "qca,ar7100-usb-phy";
+
+		reset-names = "phy", "suspend-override";
+		resets = <&rst 4>, <&rst 3>;
+
+		#phy-cells = <0>;
+
+		status = "disabled";
+	};
+};
diff --git a/arch/mips/boot/dts/qca/ar9132_tl_wr1043nd_v1.dts b/arch/mips/boot/dts/qca/ar9132_tl_wr1043nd_v1.dts
new file mode 100644
index 000000000..f3dff4009
--- /dev/null
+++ b/arch/mips/boot/dts/qca/ar9132_tl_wr1043nd_v1.dts
@@ -0,0 +1,110 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "ar9132.dtsi"
+
+/ {
+	compatible = "tplink,tl-wr1043nd-v1", "qca,ar9132";
+	model = "TP-Link TL-WR1043ND Version 1";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x2000000>;
+	};
+
+	extosc: ref {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <40000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-0 {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+
+		button-1 {
+			label = "qss";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led@0 {
+			label = "tp-link:green:usb";
+			gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+		};
+
+		led@1 {
+			label = "tp-link:green:system";
+			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led@2 {
+			label = "tp-link:green:qss";
+			gpios = <&gpio 5 GPIO_ACTIVE_HIGH>;
+		};
+
+		led@3 {
+			label = "tp-link:green:wlan";
+			gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&uart {
+	status = "okay";
+};
+
+&pll {
+	clocks = <&extosc>;
+};
+
+&usb {
+	status = "okay";
+};
+
+&usb_phy {
+	status = "okay";
+};
+
+&spi {
+	status = "okay";
+	num-cs = <1>;
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "s25sl064a";
+		reg = <0>;
+		spi-max-frequency = <25000000>;
+
+		partition@0 {
+			label = "u-boot";
+			reg = <0x000000 0x020000>;
+		};
+
+		partition@1 {
+			label = "firmware";
+			reg = <0x020000 0x7D0000>;
+		};
+
+		partition@2 {
+			label = "art";
+			reg = <0x7F0000 0x010000>;
+			read-only;
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/qca/ar9331.dtsi b/arch/mips/boot/dts/qca/ar9331.dtsi
new file mode 100644
index 000000000..c4102b280
--- /dev/null
+++ b/arch/mips/boot/dts/qca/ar9331.dtsi
@@ -0,0 +1,301 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/clock/ath79-clk.h>
+
+/ {
+	compatible = "qca,ar9331";
+
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "mips,mips24Kc";
+			clocks = <&pll ATH79_CLK_CPU>;
+			reg = <0>;
+		};
+	};
+
+	cpuintc: interrupt-controller {
+		compatible = "qca,ar7100-cpu-intc";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		qca,ddr-wb-channel-interrupts = <2>, <3>;
+		qca,ddr-wb-channels = <&ddr_ctrl 3>, <&ddr_ctrl 2>;
+	};
+
+	ref: ref {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+	};
+
+	ahb {
+		compatible = "simple-bus";
+		ranges;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		interrupt-parent = <&cpuintc>;
+
+		apb {
+			compatible = "simple-bus";
+			ranges;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			interrupt-parent = <&miscintc>;
+
+			ddr_ctrl: memory-controller@18000000 {
+				compatible = "qca,ar7240-ddr-controller";
+				reg = <0x18000000 0x100>;
+
+				#qca,ddr-wb-channel-cells = <1>;
+			};
+
+			uart: serial@18020000 {
+				compatible = "qca,ar9330-uart";
+				reg = <0x18020000 0x14>;
+
+				interrupts = <3>;
+
+				clocks = <&ref>;
+				clock-names = "uart";
+
+				status = "disabled";
+			};
+
+			gpio: gpio@18040000 {
+				compatible = "qca,ar7100-gpio";
+				reg = <0x18040000 0x34>;
+				interrupts = <2>;
+
+				ngpios = <30>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				interrupt-controller;
+				#interrupt-cells = <2>;
+
+				status = "disabled";
+			};
+
+			pll: pll-controller@18050000 {
+				compatible = "qca,ar9330-pll";
+				reg = <0x18050000 0x100>;
+
+				clocks = <&ref>;
+				clock-names = "ref";
+
+				#clock-cells = <1>;
+			};
+
+			miscintc: interrupt-controller@18060010 {
+				compatible = "qca,ar7240-misc-intc";
+				reg = <0x18060010 0x8>;
+
+				interrupt-parent = <&cpuintc>;
+				interrupts = <6>;
+
+				interrupt-controller;
+				#interrupt-cells = <1>;
+			};
+
+			rst: reset-controller@1806001c {
+				compatible = "qca,ar7100-reset";
+				reg = <0x1806001c 0x4>;
+
+				#reset-cells = <1>;
+			};
+		};
+
+		eth0: ethernet@19000000 {
+			compatible = "qca,ar9330-eth";
+			reg = <0x19000000 0x200>;
+			interrupts = <4>;
+
+			resets = <&rst 9>, <&rst 22>;
+			reset-names = "mac", "mdio";
+			clocks = <&pll ATH79_CLK_AHB>, <&pll ATH79_CLK_AHB>;
+			clock-names = "eth", "mdio";
+
+			phy-mode = "mii";
+			phy-handle = <&phy_port4>;
+
+			status = "disabled";
+		};
+
+		eth1: ethernet@1a000000 {
+			compatible = "qca,ar9330-eth";
+			reg = <0x1a000000 0x200>;
+			interrupts = <5>;
+			resets = <&rst 13>, <&rst 23>;
+			reset-names = "mac", "mdio";
+			clocks = <&pll ATH79_CLK_AHB>, <&pll ATH79_CLK_AHB>;
+			clock-names = "eth", "mdio";
+
+			phy-mode = "gmii";
+
+			status = "disabled";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+				pause;
+			};
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				switch10: switch@10 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					compatible = "qca,ar9331-switch";
+					reg = <0x10>;
+					resets = <&rst 8>;
+					reset-names = "switch";
+
+					interrupt-parent = <&miscintc>;
+					interrupts = <12>;
+
+					interrupt-controller;
+					#interrupt-cells = <1>;
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						switch_port0: port@0 {
+							reg = <0x0>;
+							label = "cpu";
+							ethernet = <&eth1>;
+
+							phy-mode = "gmii";
+
+							fixed-link {
+								speed = <1000>;
+								full-duplex;
+								pause;
+							};
+						};
+
+						switch_port1: port@1 {
+							reg = <0x1>;
+							phy-handle = <&phy_port0>;
+							phy-mode = "internal";
+
+							status = "disabled";
+						};
+
+						switch_port2: port@2 {
+							reg = <0x2>;
+							phy-handle = <&phy_port1>;
+							phy-mode = "internal";
+
+							status = "disabled";
+						};
+
+						switch_port3: port@3 {
+							reg = <0x3>;
+							phy-handle = <&phy_port2>;
+							phy-mode = "internal";
+
+							status = "disabled";
+						};
+
+						switch_port4: port@4 {
+							reg = <0x4>;
+							phy-handle = <&phy_port3>;
+							phy-mode = "internal";
+
+							status = "disabled";
+						};
+					};
+
+					mdio {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						interrupt-parent = <&switch10>;
+
+						phy_port0: phy@0 {
+							reg = <0x0>;
+							interrupts = <0>;
+							status = "disabled";
+						};
+
+						phy_port1: phy@1 {
+							reg = <0x1>;
+							interrupts = <0>;
+							status = "disabled";
+						};
+
+						phy_port2: phy@2 {
+							reg = <0x2>;
+							interrupts = <0>;
+							status = "disabled";
+						};
+
+						phy_port3: phy@3 {
+							reg = <0x3>;
+							interrupts = <0>;
+							status = "disabled";
+						};
+
+						phy_port4: phy@4 {
+							reg = <0x4>;
+							interrupts = <0>;
+							status = "disabled";
+						};
+					};
+				};
+			};
+		};
+
+		usb: usb@1b000100 {
+			compatible = "chipidea,usb2";
+			reg = <0x1b000000 0x200>;
+
+			interrupts = <3>;
+			resets = <&rst 5>;
+
+			phy-names = "usb-phy";
+			phys = <&usb_phy>;
+
+			status = "disabled";
+		};
+
+		spi: spi@1f000000 {
+			compatible = "qca,ar7100-spi";
+			reg = <0x1f000000 0x10>;
+
+			clocks = <&pll ATH79_CLK_AHB>;
+			clock-names = "ahb";
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+	};
+
+	usb_phy: usb-phy {
+		compatible = "qca,ar7100-usb-phy";
+
+		reset-names = "phy", "suspend-override";
+		resets = <&rst 4>, <&rst 3>;
+
+		#phy-cells = <0>;
+
+		status = "disabled";
+	};
+};
diff --git a/arch/mips/boot/dts/qca/ar9331_dpt_module.dts b/arch/mips/boot/dts/qca/ar9331_dpt_module.dts
new file mode 100644
index 000000000..c857cd22f
--- /dev/null
+++ b/arch/mips/boot/dts/qca/ar9331_dpt_module.dts
@@ -0,0 +1,99 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+#include "ar9331.dtsi"
+
+/ {
+	model = "DPTechnics DPT-Module";
+	compatible = "dptechnics,dpt-module";
+
+	aliases {
+		serial0 = &uart;
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x4000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-0 {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&ref {
+	clock-frequency = <25000000>;
+};
+
+&uart {
+	status = "okay";
+};
+
+&gpio {
+	status = "okay";
+};
+
+&usb {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb_phy {
+	status = "okay";
+};
+
+&spi {
+	num-chipselects = <1>;
+	status = "okay";
+
+	/* Winbond 25Q128FVSG SPI flash */
+	spiflash: w25q128@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "winbond,w25q128", "jedec,spi-nor";
+		spi-max-frequency = <104000000>;
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+};
+
+&eth1 {
+	status = "okay";
+};
+
+&switch_port1 {
+	label = "lan0";
+	status = "okay";
+};
+
+&phy_port0 {
+	status = "okay";
+};
+
+&phy_port4 {
+	status = "okay";
+};
diff --git a/arch/mips/boot/dts/qca/ar9331_dragino_ms14.dts b/arch/mips/boot/dts/qca/ar9331_dragino_ms14.dts
new file mode 100644
index 000000000..40e4c5da0
--- /dev/null
+++ b/arch/mips/boot/dts/qca/ar9331_dragino_ms14.dts
@@ -0,0 +1,100 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "ar9331.dtsi"
+
+/ {
+	model = "Dragino MS14 (Dragino 2)";
+	compatible = "dragino,ms14";
+
+	aliases {
+		serial0 = &uart;
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x4000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		wlan {
+			label = "dragino2:red:wlan";
+			gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		lan {
+			label = "dragino2:red:lan";
+			gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		wan {
+			label = "dragino2:red:wan";
+			gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		system {
+			label = "dragino2:red:system";
+			gpios = <&gpio 28 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-0 {
+			label = "jumpstart";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+		};
+
+		button-1 {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&ref {
+	clock-frequency = <25000000>;
+};
+
+&uart {
+	status = "okay";
+};
+
+&gpio {
+	status = "okay";
+};
+
+&usb {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb_phy {
+	status = "okay";
+};
+
+&spi {
+	num-chipselects = <1>;
+	status = "okay";
+
+	/* Winbond 25Q128BVFG SPI flash */
+	spiflash: w25q128@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "winbond,w25q128", "jedec,spi-nor";
+		spi-max-frequency = <104000000>;
+		reg = <0>;
+	};
+};
diff --git a/arch/mips/boot/dts/qca/ar9331_omega.dts b/arch/mips/boot/dts/qca/ar9331_omega.dts
new file mode 100644
index 000000000..ed184d861
--- /dev/null
+++ b/arch/mips/boot/dts/qca/ar9331_omega.dts
@@ -0,0 +1,76 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "ar9331.dtsi"
+
+/ {
+	model = "Onion Omega";
+	compatible = "onion,omega";
+
+	aliases {
+		serial0 = &uart;
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x4000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		system {
+			label = "onion:amber:system";
+			gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-0 {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&ref {
+	clock-frequency = <25000000>;
+};
+
+&uart {
+	status = "okay";
+};
+
+&gpio {
+	status = "okay";
+};
+
+&usb {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb_phy {
+	status = "okay";
+};
+
+&spi {
+	num-chipselects = <1>;
+	status = "okay";
+
+	/* Winbond 25Q128FVSG SPI flash */
+	spiflash: w25q128@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "winbond,w25q128", "jedec,spi-nor";
+		spi-max-frequency = <104000000>;
+		reg = <0>;
+	};
+};
diff --git a/arch/mips/boot/dts/qca/ar9331_openembed_som9331_board.dts b/arch/mips/boot/dts/qca/ar9331_openembed_som9331_board.dts
new file mode 100644
index 000000000..dc65ebd60
--- /dev/null
+++ b/arch/mips/boot/dts/qca/ar9331_openembed_som9331_board.dts
@@ -0,0 +1,108 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+#include "ar9331.dtsi"
+
+/ {
+	model = "OpenEmbed SOM9331 Board";
+	compatible = "openembed,som9331";
+
+	aliases {
+		serial0 = &uart;
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x4000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-0 {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&ref {
+	clock-frequency = <25000000>;
+};
+
+&uart {
+	status = "okay";
+};
+
+&gpio {
+	status = "okay";
+};
+
+&usb {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb_phy {
+	status = "okay";
+};
+
+&spi {
+	num-chipselects = <1>;
+	status = "okay";
+
+	/* Winbond 25Q64FVSIG SPI flash */
+	spiflash: w25q64@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "winbond,w25q64", "jedec,spi-nor";
+		spi-max-frequency = <104000000>;
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+};
+
+&eth1 {
+	status = "okay";
+};
+
+&switch_port1 {
+	label = "lan0";
+	status = "okay";
+};
+
+&switch_port3 {
+	label = "lan1";
+	status = "okay";
+};
+
+&phy_port0 {
+	status = "okay";
+};
+
+&phy_port2 {
+	status = "okay";
+};
+
+&phy_port4 {
+	status = "okay";
+};
diff --git a/arch/mips/boot/dts/qca/ar9331_tl_mr3020.dts b/arch/mips/boot/dts/qca/ar9331_tl_mr3020.dts
new file mode 100644
index 000000000..5f424c2cd
--- /dev/null
+++ b/arch/mips/boot/dts/qca/ar9331_tl_mr3020.dts
@@ -0,0 +1,116 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "ar9331.dtsi"
+
+/ {
+	model = "TP-Link TL-MR3020";
+	compatible = "tplink,tl-mr3020";
+
+	aliases {
+		serial0 = &uart;
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x2000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		wlan {
+			label = "tp-link:green:wlan";
+			gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		lan {
+			label = "tp-link:green:lan";
+			gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		wps {
+			label = "tp-link:green:wps";
+			gpios = <&gpio 26 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led3g {
+			label = "tp-link:green:3g";
+			gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-0 {
+			label = "wps";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
+		};
+
+		button-1 {
+			label = "sw1";
+			linux,code = <BTN_0>;
+			gpios = <&gpio 18 GPIO_ACTIVE_HIGH>;
+		};
+
+		button-2 {
+			label = "sw2";
+			linux,code = <BTN_1>;
+			gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	reg_usb_vbus: reg_usb_vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&ref {
+	clock-frequency = <25000000>;
+};
+
+&uart {
+	status = "okay";
+};
+
+&gpio {
+	status = "okay";
+};
+
+&usb {
+	dr_mode = "host";
+	vbus-supply = <&reg_usb_vbus>;
+	status = "okay";
+};
+
+&usb_phy {
+	status = "okay";
+};
+
+&spi {
+	num-chipselects = <1>;
+	status = "okay";
+
+	/* Spansion S25FL032PIF SPI flash */
+	spiflash: s25sl032p@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "spansion,s25sl032p", "jedec,spi-nor";
+		spi-max-frequency = <104000000>;
+		reg = <0>;
+	};
+};
diff --git a/arch/mips/boot/dts/ralink/Makefile b/arch/mips/boot/dts/ralink/Makefile
new file mode 100644
index 000000000..11732b8c8
--- /dev/null
+++ b/arch/mips/boot/dts/ralink/Makefile
@@ -0,0 +1,13 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_DTB_RT2880_EVAL)	+= rt2880_eval.dtb
+dtb-$(CONFIG_DTB_RT305X_EVAL)	+= rt3052_eval.dtb
+dtb-$(CONFIG_DTB_RT3883_EVAL)	+= rt3883_eval.dtb
+dtb-$(CONFIG_DTB_MT7620A_EVAL)	+= mt7620a_eval.dtb
+dtb-$(CONFIG_DTB_OMEGA2P)	+= omega2p.dtb
+dtb-$(CONFIG_DTB_VOCORE2)	+= vocore2.dtb
+
+dtb-$(CONFIG_SOC_MT7621) += \
+	mt7621-gnubee-gb-pc1.dtb \
+	mt7621-gnubee-gb-pc2.dtb
+
+obj-$(CONFIG_BUILTIN_DTB)	+= $(addsuffix .o, $(dtb-y))
diff --git a/arch/mips/boot/dts/ralink/gardena_smart_gateway_mt7688.dts b/arch/mips/boot/dts/ralink/gardena_smart_gateway_mt7688.dts
new file mode 100644
index 000000000..179558161
--- /dev/null
+++ b/arch/mips/boot/dts/ralink/gardena_smart_gateway_mt7688.dts
@@ -0,0 +1,205 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2019 Stefan Roese <sr@denx.de>
+ */
+
+/dts-v1/;
+
+/include/ "mt7628a.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	compatible = "gardena,smart-gateway-mt7688", "ralink,mt7688a-soc",
+		     "ralink,mt7628a-soc";
+	model = "GARDENA smart Gateway (MT7688)";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x8000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinmux_gpio_gpio>;	/* GPIO11 */
+
+		button {
+			label = "USER_BTN1";
+			gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+			linux,code =<KEY_PROG1> ;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinmux_pwm0_gpio>,	/* GPIO18 */
+			    <&pinmux_pwm1_gpio>,	/* GPIO19 */
+			    <&pinmux_sdmode_gpio>,	/* GPIO22..29 */
+			    <&pinmux_p0led_an_gpio>;	/* GPIO43 */
+		/*
+		 * <&pinmux_i2s_gpio> (covers GPIO0..3) is needed here as
+		 * well for GPIO3. But this is already claimed for uart1
+		 * (see below). So we can't include it in this LED node.
+		 */
+
+		power_blue {
+			label = "smartgw:power:blue";
+			gpios = <&gpio 18 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		power_green {
+			label = "smartgw:power:green";
+			gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		power_red {
+			label = "smartgw:power:red";
+			gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		radio_blue {
+			label = "smartgw:radio:blue";
+			gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		radio_green {
+			label = "smartgw:radio:green";
+			gpios = <&gpio 24 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		radio_red {
+			label = "smartgw:radio:red";
+			gpios = <&gpio 25 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		internet_blue {
+			label = "smartgw:internet:blue";
+			gpios = <&gpio 26 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		internet_green {
+			label = "smartgw:internet:green";
+			gpios = <&gpio 27 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		internet_red {
+			label = "smartgw:internet:red";
+			gpios = <&gpio 28 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		ethernet_link {
+			label = "smartgw:eth:link";
+			gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "netdev";
+		};
+
+		ethernet_activity {
+			label = "smartgw:eth:act";
+			gpios = <&gpio 43 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "netdev";
+		};
+	};
+
+	aliases {
+		serial0 = &uart0;
+	};
+};
+
+&i2c {
+	status = "okay";
+};
+
+&spi {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinmux_spi_spi>, <&pinmux_spi_cs1_cs>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "uboot";
+				reg = <0x0 0xa0000>;
+				read-only;
+			};
+
+			partition@a0000 {
+				label = "uboot_env0";
+				reg = <0xa0000 0x10000>;
+			};
+
+			partition@b0000 {
+				label = "uboot_env1";
+				reg = <0xb0000 0x10000>;
+			};
+
+			factory: partition@c0000 {
+				label = "factory";
+				reg = <0xc0000 0x10000>;
+				read-only;
+			};
+		};
+	};
+
+	nand_flash@1 {
+		compatible = "spi-nand";
+		linux,mtd-name = "gd5f";
+		reg = <1>;
+		spi-max-frequency = <40000000>;
+	};
+};
+
+&uart1 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinmux_i2s_gpio>;		/* GPIO0..3 */
+
+	fifo-size = <8>;
+	tx-threshold = <8>;
+
+	rts-gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+	cts-gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+};
+
+&uart2 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinmux_p2led_an_gpio>,	/* GPIO41 */
+		    <&pinmux_p3led_an_gpio>;	/* GPIO40 */
+
+	rts-gpios = <&gpio 40 GPIO_ACTIVE_LOW>;
+	cts-gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&wmac {
+	status = "okay";
+	mediatek,mtd-eeprom = <&factory 0x0000>;
+};
diff --git a/arch/mips/boot/dts/ralink/mt7620a.dtsi b/arch/mips/boot/dts/ralink/mt7620a.dtsi
new file mode 100644
index 000000000..1f6e5320f
--- /dev/null
+++ b/arch/mips/boot/dts/ralink/mt7620a.dtsi
@@ -0,0 +1,59 @@
+// SPDX-License-Identifier: GPL-2.0
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "ralink,mtk7620a-soc";
+
+	cpus {
+		cpu@0 {
+			compatible = "mips,mips24KEc";
+		};
+	};
+
+	cpuintc: cpuintc {
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		compatible = "mti,cpu-interrupt-controller";
+	};
+
+	palmbus@10000000 {
+		compatible = "palmbus";
+		reg = <0x10000000 0x200000>;
+                ranges = <0x0 0x10000000 0x1FFFFF>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		sysc@0 {
+			compatible = "ralink,mt7620a-sysc";
+			reg = <0x0 0x100>;
+		};
+
+		intc: intc@200 {
+			compatible = "ralink,mt7620a-intc", "ralink,rt2880-intc";
+			reg = <0x200 0x100>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&cpuintc>;
+			interrupts = <2>;
+		};
+
+		memc@300 {
+			compatible = "ralink,mt7620a-memc", "ralink,rt3050-memc";
+			reg = <0x300 0x100>;
+		};
+
+		uartlite@c00 {
+			compatible = "ralink,mt7620a-uart", "ralink,rt2880-uart", "ns16550a";
+			reg = <0xc00 0x100>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <12>;
+
+			reg-shift = <2>;
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/ralink/mt7620a_eval.dts b/arch/mips/boot/dts/ralink/mt7620a_eval.dts
new file mode 100644
index 000000000..8de8f89f3
--- /dev/null
+++ b/arch/mips/boot/dts/ralink/mt7620a_eval.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+/include/ "mt7620a.dtsi"
+
+/ {
+	compatible = "ralink,mt7620a-eval-board", "ralink,mt7620a-soc";
+	model = "Ralink MT7620A evaluation board";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x2000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,57600";
+	};
+};
diff --git a/arch/mips/boot/dts/ralink/mt7621-gnubee-gb-pc1.dts b/arch/mips/boot/dts/ralink/mt7621-gnubee-gb-pc1.dts
new file mode 100644
index 000000000..0128bd8fa
--- /dev/null
+++ b/arch/mips/boot/dts/ralink/mt7621-gnubee-gb-pc1.dts
@@ -0,0 +1,112 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/dts-v1/;
+
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	compatible = "gnubee,gb-pc1", "mediatek,mt7621-soc";
+	model = "GB-PC1";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x1c000000>,
+		      <0x20000000 0x04000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,57600";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-reset {
+			label = "reset";
+			gpios = <&gpio 18 GPIO_ACTIVE_HIGH>;
+			linux,code = <KEY_RESTART>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		power {
+			label = "green:power";
+			gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		system {
+			label = "green:system";
+			gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "disk-activity";
+		};
+	};
+};
+
+&mmc {
+	status = "okay";
+};
+
+&spi0 {
+	status = "okay";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+		broken-flash-reset;
+
+		partition@0 {
+			label = "u-boot";
+			reg = <0x0 0x30000>;
+			read-only;
+		};
+
+		partition@30000 {
+			label = "u-boot-env";
+			reg = <0x30000 0x10000>;
+			read-only;
+		};
+
+		factory: partition@40000 {
+			label = "factory";
+			reg = <0x40000 0x10000>;
+			read-only;
+		};
+
+		partition@50000 {
+			label = "firmware";
+			reg = <0x50000 0x1fb0000>;
+		};
+	};
+};
+
+&pcie {
+	status = "okay";
+};
+
+&gmac1 {
+	status = "okay";
+	phy-handle = <&ethphy4>;
+};
+
+&mdio {
+	ethphy4: ethernet-phy@4 {
+		reg = <4>;
+	};
+};
+
+&switch0 {
+	ports {
+		port@0 {
+			status = "okay";
+			label = "ethblack";
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/ralink/mt7621-gnubee-gb-pc2.dts b/arch/mips/boot/dts/ralink/mt7621-gnubee-gb-pc2.dts
new file mode 100644
index 000000000..751555538
--- /dev/null
+++ b/arch/mips/boot/dts/ralink/mt7621-gnubee-gb-pc2.dts
@@ -0,0 +1,138 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/dts-v1/;
+
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	compatible = "gnubee,gb-pc2", "mediatek,mt7621-soc";
+	model = "GB-PC2";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x1c000000>,
+		      <0x20000000 0x04000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,57600";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-reset {
+			label = "reset";
+			gpios = <&gpio 18 GPIO_ACTIVE_HIGH>;
+			linux,code = <KEY_RESTART>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		ethblack-green {
+			label = "green:ethblack";
+			gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+		};
+
+		ethblue-green {
+			label = "green:ethblue";
+			gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+		};
+
+		ethyellow-green {
+			label = "green:ethyellow";
+			gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+		};
+
+		ethyellow-orange {
+			label = "orange:ethyellow";
+			gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+		};
+
+		power {
+			label = "green:power";
+			gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		system {
+			label = "green:system";
+			gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "disk-activity";
+		};
+	};
+};
+
+&mmc {
+	status = "okay";
+};
+
+&spi0 {
+	status = "okay";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+		broken-flash-reset;
+
+		partition@0 {
+			label = "u-boot";
+			reg = <0x0 0x30000>;
+			read-only;
+		};
+
+		partition@30000 {
+			label = "u-boot-env";
+			reg = <0x30000 0x10000>;
+			read-only;
+		};
+
+		factory: partition@40000 {
+			label = "factory";
+			reg = <0x40000 0x10000>;
+			read-only;
+		};
+
+		partition@50000 {
+			label = "firmware";
+			reg = <0x50000 0x1fb0000>;
+		};
+	};
+};
+
+&pcie {
+	status = "okay";
+};
+
+&gmac1 {
+	status = "okay";
+	phy-handle = <&ethphy5>;
+};
+
+&mdio {
+	ethphy5: ethernet-phy@5 {
+		reg = <5>;
+		phy-mode = "rgmii-rxid";
+	};
+};
+
+&switch0 {
+	ports {
+		port@0 {
+			status = "okay";
+			label = "ethblack";
+		};
+
+		port@4 {
+			status = "okay";
+			label = "ethblue";
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/ralink/mt7621.dtsi b/arch/mips/boot/dts/ralink/mt7621.dtsi
new file mode 100644
index 000000000..f3f4c1f26
--- /dev/null
+++ b/arch/mips/boot/dts/ralink/mt7621.dtsi
@@ -0,0 +1,490 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+#include <dt-bindings/interrupt-controller/mips-gic.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/mt7621-clk.h>
+#include <dt-bindings/reset/mt7621-reset.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "mediatek,mt7621-soc";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "mips,mips1004Kc";
+			reg = <0>;
+		};
+
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "mips,mips1004Kc";
+			reg = <1>;
+		};
+	};
+
+	cpuintc: cpuintc {
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		compatible = "mti,cpu-interrupt-controller";
+	};
+
+	mmc_fixed_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "mmc_power";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	mmc_fixed_1v8_io: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "mmc_io";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	palmbus: palmbus@1e000000 {
+		compatible = "palmbus";
+		reg = <0x1e000000 0x100000>;
+		ranges = <0x0 0x1e000000 0x0fffff>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		sysc: syscon@0 {
+			compatible = "mediatek,mt7621-sysc", "syscon";
+			reg = <0x0 0x100>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			ralink,memctl = <&memc>;
+			clock-output-names = "xtal", "cpu", "bus",
+					     "50m", "125m", "150m",
+					     "250m", "270m";
+		};
+
+		wdt: wdt@100 {
+			compatible = "mediatek,mt7621-wdt";
+			reg = <0x100 0x100>;
+		};
+
+		gpio: gpio@600 {
+			#gpio-cells = <2>;
+			#interrupt-cells = <2>;
+			compatible = "mediatek,mt7621-gpio";
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 0 95>;
+			interrupt-controller;
+			reg = <0x600 0x100>;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SHARED 12 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		i2c: i2c@900 {
+			compatible = "mediatek,mt7621-i2c";
+			reg = <0x900 0x100>;
+
+			clocks = <&sysc MT7621_CLK_I2C>;
+			clock-names = "i2c";
+			resets = <&sysc MT7621_RST_I2C>;
+			reset-names = "i2c";
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c_pins>;
+		};
+
+		memc: memory-controller@5000 {
+			compatible = "mediatek,mt7621-memc", "syscon";
+			reg = <0x5000 0x1000>;
+		};
+
+		serial0: serial@c00 {
+			compatible = "ns16550a";
+			reg = <0xc00 0x100>;
+
+			clocks = <&sysc MT7621_CLK_UART1>;
+
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SHARED 26 IRQ_TYPE_LEVEL_HIGH>;
+
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			no-loopback-test;
+		};
+
+		spi0: spi@b00 {
+			status = "disabled";
+
+			compatible = "ralink,mt7621-spi";
+			reg = <0xb00 0x100>;
+
+			clocks = <&sysc MT7621_CLK_SPI>;
+			clock-names = "spi";
+
+			resets = <&sysc MT7621_RST_SPI>;
+			reset-names = "spi";
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi_pins>;
+		};
+	};
+
+	pinctrl: pinctrl {
+		compatible = "ralink,mt7621-pinctrl";
+
+		i2c_pins: i2c0-pins {
+			pinmux {
+				groups = "i2c";
+				function = "i2c";
+			};
+		};
+
+		spi_pins: spi0-pins {
+			pinmux {
+				groups = "spi";
+				function = "spi";
+			};
+		};
+
+		uart1_pins: uart1-pins {
+			pinmux {
+				groups = "uart1";
+				function = "uart1";
+			};
+		};
+
+		uart2_pins: uart2-pins {
+			pinmux {
+				groups = "uart2";
+				function = "uart2";
+			};
+		};
+
+		uart3_pins: uart3-pins {
+			pinmux {
+				groups = "uart3";
+				function = "uart3";
+			};
+		};
+
+		rgmii1_pins: rgmii1-pins {
+			pinmux {
+				groups = "rgmii1";
+				function = "rgmii1";
+			};
+		};
+
+		rgmii2_pins: rgmii2-pins {
+			pinmux {
+				groups = "rgmii2";
+				function = "rgmii2";
+			};
+		};
+
+		mdio_pins: mdio0-pins {
+			pinmux {
+				groups = "mdio";
+				function = "mdio";
+			};
+		};
+
+		pcie_pins: pcie0-pins {
+			pinmux {
+				groups = "pcie";
+				function = "gpio";
+			};
+		};
+
+		nand_pins: nand0-pins {
+			spi-pinmux {
+				groups = "spi";
+				function = "nand1";
+			};
+
+			sdhci-pinmux {
+				groups = "sdhci";
+				function = "nand2";
+			};
+		};
+
+		sdhci_pins: sdhci0-pins {
+			pinmux {
+				groups = "sdhci";
+				function = "sdhci";
+			};
+		};
+	};
+
+	mmc: mmc@1e130000 {
+		status = "disabled";
+
+		compatible = "mediatek,mt7620-mmc";
+		reg = <0x1e130000 0x4000>;
+
+		bus-width = <4>;
+		max-frequency = <48000000>;
+		cap-sd-highspeed;
+		cap-mmc-highspeed;
+		vmmc-supply = <&mmc_fixed_3v3>;
+		vqmmc-supply = <&mmc_fixed_1v8_io>;
+		disable-wp;
+
+		pinctrl-names = "default", "state_uhs";
+		pinctrl-0 = <&sdhci_pins>;
+		pinctrl-1 = <&sdhci_pins>;
+
+		clocks = <&sysc MT7621_CLK_SHXC>,
+			 <&sysc MT7621_CLK_50M>;
+		clock-names = "source", "hclk";
+
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SHARED 20 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	usb: usb@1e1c0000 {
+		compatible = "mediatek,mt8173-xhci", "mediatek,mtk-xhci";
+		reg = <0x1e1c0000 0x1000
+		       0x1e1d0700 0x0100>;
+		reg-names = "mac", "ippc";
+
+		clocks = <&sysc MT7621_CLK_XTAL>;
+		clock-names = "sys_ck";
+
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SHARED 22 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	gic: interrupt-controller@1fbc0000 {
+		compatible = "mti,gic";
+		reg = <0x1fbc0000 0x2000>;
+
+		interrupt-controller;
+		#interrupt-cells = <3>;
+
+		mti,reserved-cpu-vectors = <7>;
+
+		timer {
+			compatible = "mti,gic-timer";
+			interrupts = <GIC_LOCAL 1 IRQ_TYPE_NONE>;
+			clocks = <&sysc MT7621_CLK_CPU>;
+		};
+	};
+
+	cpc: cpc@1fbf0000 {
+		compatible = "mti,mips-cpc";
+		reg = <0x1fbf0000 0x8000>;
+	};
+
+	cdmm: cdmm@1fbf8000 {
+		compatible = "mti,mips-cdmm";
+		reg = <0x1fbf8000 0x8000>;
+	};
+
+	ethernet: ethernet@1e100000 {
+		compatible = "mediatek,mt7621-eth";
+		reg = <0x1e100000 0x10000>;
+
+		clocks = <&sysc MT7621_CLK_FE>,
+			 <&sysc MT7621_CLK_ETH>;
+		clock-names = "fe", "ethif";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		resets = <&sysc MT7621_RST_FE &sysc MT7621_RST_ETH>;
+		reset-names = "fe", "eth";
+
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SHARED 3 IRQ_TYPE_LEVEL_HIGH>;
+
+		mediatek,ethsys = <&sysc>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&mdio_pins>, <&rgmii1_pins>, <&rgmii2_pins>;
+
+		gmac0: mac@0 {
+			compatible = "mediatek,eth-mac";
+			reg = <0>;
+			phy-mode = "trgmii";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+				pause;
+			};
+		};
+
+		gmac1: mac@1 {
+			compatible = "mediatek,eth-mac";
+			reg = <1>;
+			status = "disabled";
+			phy-mode = "rgmii";
+		};
+
+		mdio: mdio-bus {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			switch0: switch@1f {
+				compatible = "mediatek,mt7621";
+				reg = <0x1f>;
+				mediatek,mcm;
+				resets = <&sysc MT7621_RST_MCM>;
+				reset-names = "mcm";
+				interrupt-controller;
+				#interrupt-cells = <1>;
+				interrupts = <GIC_SHARED 23 IRQ_TYPE_LEVEL_HIGH>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						status = "disabled";
+						reg = <0>;
+						label = "lan0";
+					};
+
+					port@1 {
+						status = "disabled";
+						reg = <1>;
+						label = "lan1";
+					};
+
+					port@2 {
+						status = "disabled";
+						reg = <2>;
+						label = "lan2";
+					};
+
+					port@3 {
+						status = "disabled";
+						reg = <3>;
+						label = "lan3";
+					};
+
+					port@4 {
+						status = "disabled";
+						reg = <4>;
+						label = "lan4";
+					};
+
+					port@6 {
+						reg = <6>;
+						label = "cpu";
+						ethernet = <&gmac0>;
+						phy-mode = "trgmii";
+
+						fixed-link {
+							speed = <1000>;
+							full-duplex;
+							pause;
+						};
+					};
+				};
+			};
+		};
+	};
+
+	pcie: pcie@1e140000 {
+		compatible = "mediatek,mt7621-pci";
+		reg = <0x1e140000 0x100>, /* host-pci bridge registers */
+		      <0x1e142000 0x100>, /* pcie port 0 RC control registers */
+		      <0x1e143000 0x100>, /* pcie port 1 RC control registers */
+		      <0x1e144000 0x100>; /* pcie port 2 RC control registers */
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pcie_pins>;
+
+		device_type = "pci";
+
+		ranges = <0x02000000 0 0x60000000 0x60000000 0 0x10000000>, /* pci memory */
+			 <0x01000000 0 0x00000000 0x1e160000 0 0x00010000>; /* io space */
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0xF800 0 0 0>;
+		interrupt-map = <0x0000 0 0 0 &gic GIC_SHARED 4 IRQ_TYPE_LEVEL_HIGH>,
+				<0x0800 0 0 0 &gic GIC_SHARED 24 IRQ_TYPE_LEVEL_HIGH>,
+				<0x1000 0 0 0 &gic GIC_SHARED 25 IRQ_TYPE_LEVEL_HIGH>;
+
+		status = "disabled";
+
+		reset-gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+
+		pcie@0,0 {
+			reg = <0x0000 0 0 0 0>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0>;
+			interrupt-map = <0 0 0 0 &gic GIC_SHARED 4 IRQ_TYPE_LEVEL_HIGH>;
+			resets = <&sysc MT7621_RST_PCIE0>;
+			clocks = <&sysc MT7621_CLK_PCIE0>;
+			phys = <&pcie0_phy 1>;
+			phy-names = "pcie-phy0";
+			ranges;
+		};
+
+		pcie@1,0 {
+			reg = <0x0800 0 0 0 0>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0>;
+			interrupt-map = <0 0 0 0 &gic GIC_SHARED 24 IRQ_TYPE_LEVEL_HIGH>;
+			resets = <&sysc MT7621_RST_PCIE1>;
+			clocks = <&sysc MT7621_CLK_PCIE1>;
+			phys = <&pcie0_phy 1>;
+			phy-names = "pcie-phy1";
+			ranges;
+		};
+
+		pcie@2,0 {
+			reg = <0x1000 0 0 0 0>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0>;
+			interrupt-map = <0 0 0 0 &gic GIC_SHARED 25 IRQ_TYPE_LEVEL_HIGH>;
+			resets = <&sysc MT7621_RST_PCIE2>;
+			clocks = <&sysc MT7621_CLK_PCIE2>;
+			phys = <&pcie2_phy 0>;
+			phy-names = "pcie-phy2";
+			ranges;
+		};
+	};
+
+	pcie0_phy: pcie-phy@1e149000 {
+		compatible = "mediatek,mt7621-pci-phy";
+		reg = <0x1e149000 0x0700>;
+		clocks = <&sysc MT7621_CLK_XTAL>;
+		#phy-cells = <1>;
+	};
+
+	pcie2_phy: pcie-phy@1e14a000 {
+		compatible = "mediatek,mt7621-pci-phy";
+		reg = <0x1e14a000 0x0700>;
+		clocks = <&sysc MT7621_CLK_XTAL>;
+		#phy-cells = <1>;
+	};
+};
diff --git a/arch/mips/boot/dts/ralink/mt7628a.dtsi b/arch/mips/boot/dts/ralink/mt7628a.dtsi
new file mode 100644
index 000000000..45bf96a3d
--- /dev/null
+++ b/arch/mips/boot/dts/ralink/mt7628a.dtsi
@@ -0,0 +1,298 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "ralink,mt7628a-soc";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "mti,mips24KEc";
+			device_type = "cpu";
+			reg = <0>;
+		};
+	};
+
+	resetc: reset-controller {
+		compatible = "ralink,rt2880-reset";
+		#reset-cells = <1>;
+	};
+
+	cpuintc: interrupt-controller {
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		compatible = "mti,cpu-interrupt-controller";
+	};
+
+	palmbus@10000000 {
+		compatible = "palmbus";
+		reg = <0x10000000 0x200000>;
+		ranges = <0x0 0x10000000 0x1FFFFF>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		sysc: system-controller@0 {
+			compatible = "ralink,mt7620a-sysc", "syscon";
+			reg = <0x0 0x60>;
+		};
+
+		pinmux: pinmux@60 {
+			compatible = "pinctrl-single";
+			reg = <0x60 0x8>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#pinctrl-cells = <2>;
+			pinctrl-single,bit-per-mux;
+			pinctrl-single,register-width = <32>;
+			pinctrl-single,function-mask = <0x1>;
+
+			pinmux_gpio_gpio: pinmux_gpio_gpio {
+				pinctrl-single,bits = <0x0 0x0 0x3>;
+			};
+
+			pinmux_spi_cs1_cs: pinmux_spi_cs1_cs {
+				pinctrl-single,bits = <0x0 0x0 0x30>;
+			};
+
+			pinmux_i2s_gpio: pinmux_i2s_gpio {
+				pinctrl-single,bits = <0x0 0x40 0xc0>;
+			};
+
+			pinmux_uart0_uart: pinmux_uart0_uart0 {
+				pinctrl-single,bits = <0x0 0x0 0x300>;
+			};
+
+			pinmux_sdmode_sdxc: pinmux_sdmode_sdxc {
+				pinctrl-single,bits = <0x0 0x0 0xc00>;
+			};
+
+			pinmux_sdmode_gpio: pinmux_sdmode_gpio {
+				pinctrl-single,bits = <0x0 0x400 0xc00>;
+			};
+
+			pinmux_spi_spi: pinmux_spi_spi {
+				pinctrl-single,bits = <0x0 0x0 0x1000>;
+			};
+
+			pinmux_refclk_gpio: pinmux_refclk_gpio {
+				pinctrl-single,bits = <0x0 0x40000 0x40000>;
+			};
+
+			pinmux_i2c_i2c: pinmux_i2c_i2c {
+				pinctrl-single,bits = <0x0 0x0 0x300000>;
+			};
+
+			pinmux_uart1_uart: pinmux_uart1_uart1 {
+				pinctrl-single,bits = <0x0 0x0 0x3000000>;
+			};
+
+			pinmux_uart2_uart: pinmux_uart2_uart {
+				pinctrl-single,bits = <0x0 0x0 0xc000000>;
+			};
+
+			pinmux_pwm0_pwm: pinmux_pwm0_pwm {
+				pinctrl-single,bits = <0x0 0x0 0x30000000>;
+			};
+
+			pinmux_pwm0_gpio: pinmux_pwm0_gpio {
+				pinctrl-single,bits = <0x0 0x10000000
+						       0x30000000>;
+			};
+
+			pinmux_pwm1_pwm: pinmux_pwm1_pwm {
+				pinctrl-single,bits = <0x0 0x0 0xc0000000>;
+			};
+
+			pinmux_pwm1_gpio: pinmux_pwm1_gpio {
+				pinctrl-single,bits = <0x0 0x40000000
+						       0xc0000000>;
+			};
+
+			pinmux_p0led_an_gpio: pinmux_p0led_an_gpio {
+				pinctrl-single,bits = <0x4 0x4 0xc>;
+			};
+
+			pinmux_p1led_an_gpio: pinmux_p1led_an_gpio {
+				pinctrl-single,bits = <0x4 0x10 0x30>;
+			};
+
+			pinmux_p2led_an_gpio: pinmux_p2led_an_gpio {
+				pinctrl-single,bits = <0x4 0x40 0xc0>;
+			};
+
+			pinmux_p3led_an_gpio: pinmux_p3led_an_gpio {
+				pinctrl-single,bits = <0x4 0x100 0x300>;
+			};
+
+			pinmux_p4led_an_gpio: pinmux_p4led_an_gpio {
+				pinctrl-single,bits = <0x4 0x400 0xc00>;
+			};
+		};
+
+		watchdog: watchdog@100 {
+			compatible = "mediatek,mt7621-wdt";
+			reg = <0x100 0x30>;
+
+			resets = <&resetc 8>;
+			reset-names = "wdt";
+
+			interrupt-parent = <&intc>;
+			interrupts = <24>;
+
+			status = "disabled";
+		};
+
+		intc: interrupt-controller@200 {
+			compatible = "ralink,rt2880-intc";
+			reg = <0x200 0x100>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			resets = <&resetc 9>;
+			reset-names = "intc";
+
+			interrupt-parent = <&cpuintc>;
+			interrupts = <2>;
+
+			ralink,intc-registers = <0x9c 0xa0
+						 0x6c 0xa4
+						 0x80 0x78>;
+		};
+
+		memory-controller@300 {
+			compatible = "ralink,mt7620a-memc";
+			reg = <0x300 0x100>;
+		};
+
+		gpio: gpio@600 {
+			compatible = "mediatek,mt7621-gpio";
+			reg = <0x600 0x100>;
+
+			gpio-controller;
+			interrupt-controller;
+			#gpio-cells = <2>;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <6>;
+		};
+
+		spi: spi@b00 {
+			compatible = "ralink,mt7621-spi";
+			reg = <0xb00 0x100>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinmux_spi_spi>;
+
+			resets = <&resetc 18>;
+			reset-names = "spi";
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		i2c: i2c@900 {
+			compatible = "mediatek,mt7621-i2c";
+			reg = <0x900 0x100>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinmux_i2c_i2c>;
+
+			resets = <&resetc 16>;
+			reset-names = "i2c";
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		uart0: uartlite@c00 {
+			compatible = "ns16550a";
+			reg = <0xc00 0x100>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinmux_uart0_uart>;
+
+			resets = <&resetc 12>;
+			reset-names = "uart0";
+
+			interrupt-parent = <&intc>;
+			interrupts = <20>;
+
+			reg-shift = <2>;
+		};
+
+		uart1: uart1@d00 {
+			compatible = "ns16550a";
+			reg = <0xd00 0x100>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinmux_uart1_uart>;
+
+			resets = <&resetc 19>;
+			reset-names = "uart1";
+
+			interrupt-parent = <&intc>;
+			interrupts = <21>;
+
+			reg-shift = <2>;
+		};
+
+		uart2: uart2@e00 {
+			compatible = "ns16550a";
+			reg = <0xe00 0x100>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinmux_uart2_uart>;
+
+			resets = <&resetc 20>;
+			reset-names = "uart2";
+
+			interrupt-parent = <&intc>;
+			interrupts = <22>;
+
+			reg-shift = <2>;
+		};
+	};
+
+	usb_phy: usb-phy@10120000 {
+		compatible = "mediatek,mt7628-usbphy";
+		reg = <0x10120000 0x1000>;
+
+		#phy-cells = <0>;
+
+		ralink,sysctl = <&sysc>;
+		resets = <&resetc 22 &resetc 25>;
+		reset-names = "host", "device";
+	};
+
+	usb@101c0000 {
+		compatible = "generic-ehci";
+		reg = <0x101c0000 0x1000>;
+
+		phys = <&usb_phy>;
+		phy-names = "usb";
+
+		interrupt-parent = <&intc>;
+		interrupts = <18>;
+	};
+
+	wmac: wmac@10300000 {
+		compatible = "mediatek,mt7628-wmac";
+		reg = <0x10300000 0x100000>;
+
+		interrupt-parent = <&cpuintc>;
+		interrupts = <6>;
+
+		status = "disabled";
+	};
+};
diff --git a/arch/mips/boot/dts/ralink/omega2p.dts b/arch/mips/boot/dts/ralink/omega2p.dts
new file mode 100644
index 000000000..5884fd48f
--- /dev/null
+++ b/arch/mips/boot/dts/ralink/omega2p.dts
@@ -0,0 +1,18 @@
+/dts-v1/;
+
+/include/ "mt7628a.dtsi"
+
+/ {
+	compatible = "onion,omega2+", "ralink,mt7688a-soc", "ralink,mt7628a-soc";
+	model = "Onion Omega2+";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x8000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &uart0;
+	};
+};
diff --git a/arch/mips/boot/dts/ralink/rt2880.dtsi b/arch/mips/boot/dts/ralink/rt2880.dtsi
new file mode 100644
index 000000000..8fc1987d9
--- /dev/null
+++ b/arch/mips/boot/dts/ralink/rt2880.dtsi
@@ -0,0 +1,59 @@
+// SPDX-License-Identifier: GPL-2.0
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "ralink,rt2880-soc";
+
+	cpus {
+		cpu@0 {
+			compatible = "mips,mips4KEc";
+		};
+	};
+
+	cpuintc: cpuintc {
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		compatible = "mti,cpu-interrupt-controller";
+	};
+
+	palmbus@300000 {
+		compatible = "palmbus";
+		reg = <0x300000 0x200000>;
+                ranges = <0x0 0x300000 0x1FFFFF>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		sysc@0 {
+			compatible = "ralink,rt2880-sysc";
+			reg = <0x0 0x100>;
+		};
+
+		intc: intc@200 {
+			compatible = "ralink,rt2880-intc";
+			reg = <0x200 0x100>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&cpuintc>;
+			interrupts = <2>;
+		};
+
+		memc@300 {
+			compatible = "ralink,rt2880-memc";
+			reg = <0x300 0x100>;
+		};
+
+		uartlite@c00 {
+			compatible = "ralink,rt2880-uart", "ns16550a";
+			reg = <0xc00 0x100>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <8>;
+
+			reg-shift = <2>;
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/ralink/rt2880_eval.dts b/arch/mips/boot/dts/ralink/rt2880_eval.dts
new file mode 100644
index 000000000..759bc1dd5
--- /dev/null
+++ b/arch/mips/boot/dts/ralink/rt2880_eval.dts
@@ -0,0 +1,48 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+/include/ "rt2880.dtsi"
+
+/ {
+	compatible = "ralink,rt2880-eval-board", "ralink,rt2880-soc";
+	model = "Ralink RT2880 evaluation board";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x8000000 0x2000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,57600";
+	};
+
+	cfi@1f000000 {
+		compatible = "cfi-flash";
+		reg = <0x1f000000 0x400000>;
+
+		bank-width = <2>;
+		device-width = <2>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "uboot";
+			reg = <0x0 0x30000>;
+			read-only;
+		};
+		partition@30000 {
+			label = "uboot-env";
+			reg = <0x30000 0x10000>;
+			read-only;
+		};
+		partition@40000 {
+			label = "calibration";
+			reg = <0x40000 0x10000>;
+			read-only;
+		};
+		partition@50000 {
+			label = "linux";
+			reg = <0x50000 0x3b0000>;
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/ralink/rt3050.dtsi b/arch/mips/boot/dts/ralink/rt3050.dtsi
new file mode 100644
index 000000000..23062333a
--- /dev/null
+++ b/arch/mips/boot/dts/ralink/rt3050.dtsi
@@ -0,0 +1,69 @@
+// SPDX-License-Identifier: GPL-2.0
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "ralink,rt3050-soc", "ralink,rt3052-soc", "ralink,rt3350-soc";
+
+	cpus {
+		cpu@0 {
+			compatible = "mips,mips24KEc";
+		};
+	};
+
+	cpuintc: cpuintc {
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		compatible = "mti,cpu-interrupt-controller";
+	};
+
+	palmbus@10000000 {
+		compatible = "palmbus";
+		reg = <0x10000000 0x200000>;
+		ranges = <0x0 0x10000000 0x1FFFFF>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		sysc@0 {
+			compatible = "ralink,rt3052-sysc", "ralink,rt3050-sysc";
+			reg = <0x0 0x100>;
+		};
+
+		intc: intc@200 {
+			compatible = "ralink,rt3052-intc", "ralink,rt2880-intc";
+			reg = <0x200 0x100>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&cpuintc>;
+			interrupts = <2>;
+		};
+
+		memc@300 {
+			compatible = "ralink,rt3052-memc", "ralink,rt3050-memc";
+			reg = <0x300 0x100>;
+		};
+
+		uartlite@c00 {
+			compatible = "ralink,rt3052-uart", "ralink,rt2880-uart", "ns16550a";
+			reg = <0xc00 0x100>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <12>;
+
+			reg-shift = <2>;
+		};
+	};
+
+	usb@101c0000 {
+		compatible = "ralink,rt3050-usb", "snps,dwc2";
+		reg = <0x101c0000 40000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <18>;
+
+		status = "disabled";
+	};
+};
diff --git a/arch/mips/boot/dts/ralink/rt3052_eval.dts b/arch/mips/boot/dts/ralink/rt3052_eval.dts
new file mode 100644
index 000000000..6408ff629
--- /dev/null
+++ b/arch/mips/boot/dts/ralink/rt3052_eval.dts
@@ -0,0 +1,52 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "rt3050.dtsi"
+
+/ {
+	compatible = "ralink,rt3052-eval-board", "ralink,rt3052-soc";
+	model = "Ralink RT3052 evaluation board";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x2000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,57600";
+	};
+
+	cfi@1f000000 {
+		compatible = "cfi-flash";
+		reg = <0x1f000000 0x800000>;
+
+		bank-width = <2>;
+		device-width = <2>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "uboot";
+			reg = <0x0 0x30000>;
+			read-only;
+		};
+		partition@30000 {
+			label = "uboot-env";
+			reg = <0x30000 0x10000>;
+			read-only;
+		};
+		partition@40000 {
+			label = "calibration";
+			reg = <0x40000 0x10000>;
+			read-only;
+		};
+		partition@50000 {
+			label = "linux";
+			reg = <0x50000 0x7b0000>;
+		};
+	};
+
+	usb@101c0000 {
+		status = "okay";
+	};
+};
diff --git a/arch/mips/boot/dts/ralink/rt3883.dtsi b/arch/mips/boot/dts/ralink/rt3883.dtsi
new file mode 100644
index 000000000..61132cf15
--- /dev/null
+++ b/arch/mips/boot/dts/ralink/rt3883.dtsi
@@ -0,0 +1,59 @@
+// SPDX-License-Identifier: GPL-2.0
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "ralink,rt3883-soc";
+
+	cpus {
+		cpu@0 {
+			compatible = "mips,mips74Kc";
+		};
+	};
+
+	cpuintc: cpuintc {
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		compatible = "mti,cpu-interrupt-controller";
+	};
+
+	palmbus@10000000 {
+		compatible = "palmbus";
+		reg = <0x10000000 0x200000>;
+		ranges = <0x0 0x10000000 0x1FFFFF>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		sysc@0 {
+			compatible = "ralink,rt3883-sysc", "ralink,rt3050-sysc";
+			reg = <0x0 0x100>;
+		};
+
+		intc: intc@200 {
+			compatible = "ralink,rt3883-intc", "ralink,rt2880-intc";
+			reg = <0x200 0x100>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interrupt-parent = <&cpuintc>;
+			interrupts = <2>;
+		};
+
+		memc@300 {
+			compatible = "ralink,rt3883-memc", "ralink,rt3050-memc";
+			reg = <0x300 0x100>;
+		};
+
+		uartlite@c00 {
+			compatible = "ralink,rt3883-uart", "ralink,rt2880-uart", "ns16550a";
+			reg = <0xc00 0x100>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <12>;
+
+			reg-shift = <2>;
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/ralink/rt3883_eval.dts b/arch/mips/boot/dts/ralink/rt3883_eval.dts
new file mode 100644
index 000000000..c22bc84df
--- /dev/null
+++ b/arch/mips/boot/dts/ralink/rt3883_eval.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+/include/ "rt3883.dtsi"
+
+/ {
+	compatible = "ralink,rt3883-eval-board", "ralink,rt3883-soc";
+	model = "Ralink RT3883 evaluation board";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x2000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,57600";
+	};
+};
diff --git a/arch/mips/boot/dts/ralink/vocore2.dts b/arch/mips/boot/dts/ralink/vocore2.dts
new file mode 100644
index 000000000..fa8a5f8f2
--- /dev/null
+++ b/arch/mips/boot/dts/ralink/vocore2.dts
@@ -0,0 +1,18 @@
+/dts-v1/;
+
+#include "mt7628a.dtsi"
+
+/ {
+	compatible = "vocore,vocore2", "ralink,mt7628a-soc";
+	model = "VoCore2";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x8000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS2,115200";
+		stdout-path = &uart2;
+	};
+};
diff --git a/arch/mips/boot/dts/realtek/Makefile b/arch/mips/boot/dts/realtek/Makefile
new file mode 100644
index 000000000..fba4e9318
--- /dev/null
+++ b/arch/mips/boot/dts/realtek/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-y	+= cisco_sg220-26.dtb
diff --git a/arch/mips/boot/dts/realtek/cisco_sg220-26.dts b/arch/mips/boot/dts/realtek/cisco_sg220-26.dts
new file mode 100644
index 000000000..1cdbb0929
--- /dev/null
+++ b/arch/mips/boot/dts/realtek/cisco_sg220-26.dts
@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR BSD-2-Clause
+
+/dts-v1/;
+
+#include "rtl83xx.dtsi"
+#include "rtl838x.dtsi"
+
+/ {
+	model = "Cisco SG220-26";
+	compatible = "cisco,sg220-26", "realtek,rtl8382-soc";
+
+	chosen {
+		stdout-path = "serial0:9600n8";
+		bootargs = "earlycon console=ttyS0,9600";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x8000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/mips/boot/dts/realtek/rtl838x.dtsi b/arch/mips/boot/dts/realtek/rtl838x.dtsi
new file mode 100644
index 000000000..6cc4ff5c0
--- /dev/null
+++ b/arch/mips/boot/dts/realtek/rtl838x.dtsi
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR BSD-2-Clause
+
+/ {
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "mips,mips4KEc";
+			reg = <0>;
+			clocks = <&baseclk 0>;
+			clock-names = "cpu";
+		};
+	};
+
+	baseclk: baseclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <500000000>;
+	};
+};
diff --git a/arch/mips/boot/dts/realtek/rtl83xx.dtsi b/arch/mips/boot/dts/realtek/rtl83xx.dtsi
new file mode 100644
index 000000000..de65a111b
--- /dev/null
+++ b/arch/mips/boot/dts/realtek/rtl83xx.dtsi
@@ -0,0 +1,59 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR BSD-2-Clause
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+	};
+
+	cpuintc: cpuintc {
+		compatible = "mti,cpu-interrupt-controller";
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+	};
+
+	soc: soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x18000000 0x10000>;
+
+		uart0: uart@2000 {
+			compatible = "ns16550a";
+			reg = <0x2000 0x100>;
+
+			clock-frequency = <200000000>;
+
+			interrupt-parent = <&cpuintc>;
+			interrupts = <31>;
+
+			reg-io-width = <1>;
+			reg-shift = <2>;
+			fifo-size = <1>;
+			no-loopback-test;
+
+			status = "disabled";
+		};
+
+		uart1: uart@2100 {
+			compatible = "ns16550a";
+			reg = <0x2100 0x100>;
+
+			clock-frequency = <200000000>;
+
+			interrupt-parent = <&cpuintc>;
+			interrupts = <30>;
+
+			reg-io-width = <1>;
+			reg-shift = <2>;
+			fifo-size = <1>;
+			no-loopback-test;
+
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/mips/boot/dts/xilfpga/Makefile b/arch/mips/boot/dts/xilfpga/Makefile
new file mode 100644
index 000000000..69ca00590
--- /dev/null
+++ b/arch/mips/boot/dts/xilfpga/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_FIT_IMAGE_FDT_XILFPGA)	+= nexys4ddr.dtb
diff --git a/arch/mips/boot/dts/xilfpga/microAptiv.dtsi b/arch/mips/boot/dts/xilfpga/microAptiv.dtsi
new file mode 100644
index 000000000..87b2b1f9a
--- /dev/null
+++ b/arch/mips/boot/dts/xilfpga/microAptiv.dtsi
@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: GPL-2.0
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "img,xilfpga";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "mips,m14Kc";
+			clocks	= <&ext>;
+			reg = <0>;
+		};
+	};
+
+	ext: ext {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+	};
+};
diff --git a/arch/mips/boot/dts/xilfpga/nexys4ddr.dts b/arch/mips/boot/dts/xilfpga/nexys4ddr.dts
new file mode 100644
index 000000000..cc8dbea09
--- /dev/null
+++ b/arch/mips/boot/dts/xilfpga/nexys4ddr.dts
@@ -0,0 +1,118 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "microAptiv.dtsi"
+
+/ {
+	compatible = "digilent,nexys4ddr";
+
+	aliases {
+		serial0 = &axi_uart16550;
+	};
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+
+	cpuintc: interrupt-controller {
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		compatible = "mti,cpu-interrupt-controller";
+	};
+
+	axi_intc: interrupt-controller@10200000 {
+		#interrupt-cells = <1>;
+		compatible = "xlnx,xps-intc-1.00.a";
+		interrupt-controller;
+		reg = <0x10200000 0x10000>;
+		xlnx,kind-of-intr = <0x0>;
+		xlnx,num-intr-inputs = <0x6>;
+
+		interrupt-parent = <&cpuintc>;
+		interrupts = <6>;
+	};
+
+	axi_gpio: gpio@10600000 {
+		#gpio-cells = <1>;
+		compatible = "xlnx,xps-gpio-1.00.a";
+		gpio-controller;
+		reg = <0x10600000 0x10000>;
+		xlnx,all-inputs = <0x0>;
+		xlnx,dout-default = <0x0>;
+		xlnx,gpio-width = <0x16>;
+		xlnx,interrupt-present = <0x0>;
+		xlnx,is-dual = <0x0>;
+		xlnx,tri-default = <0xffffffff>;
+	} ;
+
+	axi_ethernetlite: ethernet@10e00000 {
+		compatible = "xlnx,xps-ethernetlite-3.00.a";
+		device_type = "network";
+		interrupt-parent = <&axi_intc>;
+		interrupts = <1>;
+		phy-handle = <&phy0>;
+		reg = <0x10e00000 0x10000>;
+		xlnx,duplex = <0x1>;
+		xlnx,include-global-buffers = <0x1>;
+		xlnx,include-internal-loopback = <0x0>;
+		xlnx,include-mdio = <0x1>;
+		xlnx,instance = "axi_ethernetlite_inst";
+		xlnx,rx-ping-pong = <0x1>;
+		xlnx,s-axi-id-width = <0x1>;
+		xlnx,tx-ping-pong = <0x1>;
+		xlnx,use-internal = <0x0>;
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			phy0: phy@1 {
+				device_type = "ethernet-phy";
+				reg = <1>;
+			};
+		};
+	};
+
+	axi_uart16550: serial@10400000 {
+		compatible = "ns16550a";
+		reg = <0x10400000 0x10000>;
+
+		reg-shift = <2>;
+		reg-offset = <0x1000>;
+
+		clocks	= <&ext>;
+
+		interrupt-parent = <&axi_intc>;
+		interrupts = <0>;
+	};
+
+	axi_i2c: i2c@10a00000 {
+	    compatible = "xlnx,xps-iic-2.00.a";
+	    interrupt-parent = <&axi_intc>;
+	    interrupts = <4>;
+	    reg = < 0x10a00000 0x10000 >;
+	    clocks = <&ext>;
+	    xlnx,clk-freq = <0x5f5e100>;
+	    xlnx,family = "Artix7";
+	    xlnx,gpo-width = <0x1>;
+	    xlnx,iic-freq = <0x186a0>;
+	    xlnx,scl-inertial-delay = <0x0>;
+	    xlnx,sda-inertial-delay = <0x0>;
+	    xlnx,ten-bit-adr = <0x0>;
+	    #address-cells = <1>;
+	    #size-cells = <0>;
+
+	    ad7420@4b {
+		compatible = "adi,adt7420";
+		reg = <0x4b>;
+	    };
+	} ;
+};
+
+&ext {
+	clock-frequency = <50000000>;
+};
diff --git a/arch/mips/boot/ecoff.h b/arch/mips/boot/ecoff.h
new file mode 100644
index 000000000..5be79ebfc
--- /dev/null
+++ b/arch/mips/boot/ecoff.h
@@ -0,0 +1,65 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Some ECOFF definitions.
+ */
+
+#include <stdint.h>
+
+typedef struct filehdr {
+	uint16_t	f_magic;	/* magic number */
+	uint16_t	f_nscns;	/* number of sections */
+	int32_t		f_timdat;	/* time & date stamp */
+	int32_t		f_symptr;	/* file pointer to symbolic header */
+	int32_t		f_nsyms;	/* sizeof(symbolic hdr) */
+	uint16_t	f_opthdr;	/* sizeof(optional hdr) */
+	uint16_t	f_flags;	/* flags */
+} FILHDR;
+#define FILHSZ	sizeof(FILHDR)
+
+#define MIPSEBMAGIC	0x160
+#define MIPSELMAGIC	0x162
+
+typedef struct scnhdr {
+	char		s_name[8];	/* section name */
+	int32_t		s_paddr;	/* physical address, aliased s_nlib */
+	int32_t		s_vaddr;	/* virtual address */
+	int32_t		s_size;		/* section size */
+	int32_t		s_scnptr;	/* file ptr to raw data for section */
+	int32_t		s_relptr;	/* file ptr to relocation */
+	int32_t		s_lnnoptr;	/* file ptr to gp histogram */
+	uint16_t	s_nreloc;	/* number of relocation entries */
+	uint16_t	s_nlnno;	/* number of gp histogram entries */
+	int32_t		s_flags;	/* flags */
+} SCNHDR;
+#define SCNHSZ		sizeof(SCNHDR)
+#define SCNROUND	((int32_t)16)
+
+typedef struct aouthdr {
+	int16_t	magic;		/* see above				*/
+	int16_t	vstamp;		/* version stamp			*/
+	int32_t	tsize;		/* text size in bytes, padded to DW bdry*/
+	int32_t	dsize;		/* initialized data "  "		*/
+	int32_t	bsize;		/* uninitialized data "	  "		*/
+	int32_t	entry;		/* entry pt.				*/
+	int32_t	text_start;	/* base of text used for this file	*/
+	int32_t	data_start;	/* base of data used for this file	*/
+	int32_t	bss_start;	/* base of bss used for this file	*/
+	int32_t	gprmask;	/* general purpose register mask	*/
+	int32_t	cprmask[4];	/* co-processor register masks		*/
+	int32_t	gp_value;	/* the gp value used for this object	*/
+} AOUTHDR;
+#define AOUTHSZ sizeof(AOUTHDR)
+
+#define OMAGIC		0407
+#define NMAGIC		0410
+#define ZMAGIC		0413
+#define SMAGIC		0411
+#define LIBMAGIC	0443
+
+#define N_TXTOFF(f, a) \
+ ((a).magic == ZMAGIC || (a).magic == LIBMAGIC ? 0 : \
+  ((a).vstamp < 23 ? \
+   ((FILHSZ + AOUTHSZ + (f).f_nscns * SCNHSZ + 7) & 0xfffffff8) : \
+   ((FILHSZ + AOUTHSZ + (f).f_nscns * SCNHSZ + SCNROUND-1) & ~(SCNROUND-1)) ) )
+#define N_DATOFF(f, a) \
+  N_TXTOFF(f, a) + (a).tsize;
diff --git a/arch/mips/boot/elf2ecoff.c b/arch/mips/boot/elf2ecoff.c
new file mode 100644
index 000000000..6972b9723
--- /dev/null
+++ b/arch/mips/boot/elf2ecoff.c
@@ -0,0 +1,621 @@
+/*
+ * Copyright (c) 1995
+ *	Ted Lemon (hereinafter referred to as the author)
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in the
+ *    documentation and/or other materials provided with the distribution.
+ * 3. The name of the author may not be used to endorse or promote products
+ *    derived from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND
+ * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED.  IN NO EVENT SHALL THE AUTHOR BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
+ * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+ * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
+ * SUCH DAMAGE.
+ */
+
+/* elf2ecoff.c
+
+   This program converts an elf executable to an ECOFF executable.
+   No symbol table is retained.	  This is useful primarily in building
+   net-bootable kernels for machines (e.g., DECstation and Alpha) which
+   only support the ECOFF object file format. */
+
+#include <stdio.h>
+#include <string.h>
+#include <errno.h>
+#include <sys/types.h>
+#include <fcntl.h>
+#include <unistd.h>
+#include <elf.h>
+#include <limits.h>
+#include <netinet/in.h>
+#include <stdlib.h>
+#include <stdint.h>
+#include <inttypes.h>
+
+#include "ecoff.h"
+
+/*
+ * Some extra ELF definitions
+ */
+#define PT_MIPS_REGINFO 	0x70000000	/* Register usage information */
+#define PT_MIPS_ABIFLAGS	0x70000003	/* Records ABI related flags  */
+
+/* -------------------------------------------------------------------- */
+
+struct sect {
+	uint32_t vaddr;
+	uint32_t len;
+};
+
+int *symTypeTable;
+int must_convert_endian;
+int format_bigendian;
+
+static void copy(int out, int in, off_t offset, off_t size)
+{
+	char ibuf[4096];
+	int remaining, cur, count;
+
+	/* Go to the start of the ELF symbol table... */
+	if (lseek(in, offset, SEEK_SET) < 0) {
+		perror("copy: lseek");
+		exit(1);
+	}
+
+	remaining = size;
+	while (remaining) {
+		cur = remaining;
+		if (cur > sizeof ibuf)
+			cur = sizeof ibuf;
+		remaining -= cur;
+		if ((count = read(in, ibuf, cur)) != cur) {
+			fprintf(stderr, "copy: read: %s\n",
+				count ? strerror(errno) :
+				"premature end of file");
+			exit(1);
+		}
+		if ((count = write(out, ibuf, cur)) != cur) {
+			perror("copy: write");
+			exit(1);
+		}
+	}
+}
+
+/*
+ * Combine two segments, which must be contiguous.   If pad is true, it's
+ * okay for there to be padding between.
+ */
+static void combine(struct sect *base, struct sect *new, int pad)
+{
+	if (!base->len)
+		*base = *new;
+	else if (new->len) {
+		if (base->vaddr + base->len != new->vaddr) {
+			if (pad)
+				base->len = new->vaddr - base->vaddr;
+			else {
+				fprintf(stderr,
+					"Non-contiguous data can't be converted.\n");
+				exit(1);
+			}
+		}
+		base->len += new->len;
+	}
+}
+
+static int phcmp(const void *v1, const void *v2)
+{
+	const Elf32_Phdr *h1 = v1;
+	const Elf32_Phdr *h2 = v2;
+
+	if (h1->p_vaddr > h2->p_vaddr)
+		return 1;
+	else if (h1->p_vaddr < h2->p_vaddr)
+		return -1;
+	else
+		return 0;
+}
+
+static char *saveRead(int file, off_t offset, off_t len, char *name)
+{
+	char *tmp;
+	int count;
+	off_t off;
+	if ((off = lseek(file, offset, SEEK_SET)) < 0) {
+		fprintf(stderr, "%s: fseek: %s\n", name, strerror(errno));
+		exit(1);
+	}
+	if (!(tmp = (char *) malloc(len))) {
+		fprintf(stderr, "%s: Can't allocate %ld bytes.\n", name,
+			len);
+		exit(1);
+	}
+	count = read(file, tmp, len);
+	if (count != len) {
+		fprintf(stderr, "%s: read: %s.\n",
+			name,
+			count ? strerror(errno) : "End of file reached");
+		exit(1);
+	}
+	return tmp;
+}
+
+#define swab16(x) \
+	((uint16_t)( \
+		(((uint16_t)(x) & (uint16_t)0x00ffU) << 8) | \
+		(((uint16_t)(x) & (uint16_t)0xff00U) >> 8) ))
+
+#define swab32(x) \
+	((unsigned int)( \
+		(((uint32_t)(x) & (uint32_t)0x000000ffUL) << 24) | \
+		(((uint32_t)(x) & (uint32_t)0x0000ff00UL) <<  8) | \
+		(((uint32_t)(x) & (uint32_t)0x00ff0000UL) >>  8) | \
+		(((uint32_t)(x) & (uint32_t)0xff000000UL) >> 24) ))
+
+static void convert_elf_hdr(Elf32_Ehdr * e)
+{
+	e->e_type = swab16(e->e_type);
+	e->e_machine = swab16(e->e_machine);
+	e->e_version = swab32(e->e_version);
+	e->e_entry = swab32(e->e_entry);
+	e->e_phoff = swab32(e->e_phoff);
+	e->e_shoff = swab32(e->e_shoff);
+	e->e_flags = swab32(e->e_flags);
+	e->e_ehsize = swab16(e->e_ehsize);
+	e->e_phentsize = swab16(e->e_phentsize);
+	e->e_phnum = swab16(e->e_phnum);
+	e->e_shentsize = swab16(e->e_shentsize);
+	e->e_shnum = swab16(e->e_shnum);
+	e->e_shstrndx = swab16(e->e_shstrndx);
+}
+
+static void convert_elf_phdrs(Elf32_Phdr * p, int num)
+{
+	int i;
+
+	for (i = 0; i < num; i++, p++) {
+		p->p_type = swab32(p->p_type);
+		p->p_offset = swab32(p->p_offset);
+		p->p_vaddr = swab32(p->p_vaddr);
+		p->p_paddr = swab32(p->p_paddr);
+		p->p_filesz = swab32(p->p_filesz);
+		p->p_memsz = swab32(p->p_memsz);
+		p->p_flags = swab32(p->p_flags);
+		p->p_align = swab32(p->p_align);
+	}
+
+}
+
+static void convert_elf_shdrs(Elf32_Shdr * s, int num)
+{
+	int i;
+
+	for (i = 0; i < num; i++, s++) {
+		s->sh_name = swab32(s->sh_name);
+		s->sh_type = swab32(s->sh_type);
+		s->sh_flags = swab32(s->sh_flags);
+		s->sh_addr = swab32(s->sh_addr);
+		s->sh_offset = swab32(s->sh_offset);
+		s->sh_size = swab32(s->sh_size);
+		s->sh_link = swab32(s->sh_link);
+		s->sh_info = swab32(s->sh_info);
+		s->sh_addralign = swab32(s->sh_addralign);
+		s->sh_entsize = swab32(s->sh_entsize);
+	}
+}
+
+static void convert_ecoff_filehdr(struct filehdr *f)
+{
+	f->f_magic = swab16(f->f_magic);
+	f->f_nscns = swab16(f->f_nscns);
+	f->f_timdat = swab32(f->f_timdat);
+	f->f_symptr = swab32(f->f_symptr);
+	f->f_nsyms = swab32(f->f_nsyms);
+	f->f_opthdr = swab16(f->f_opthdr);
+	f->f_flags = swab16(f->f_flags);
+}
+
+static void convert_ecoff_aouthdr(struct aouthdr *a)
+{
+	a->magic = swab16(a->magic);
+	a->vstamp = swab16(a->vstamp);
+	a->tsize = swab32(a->tsize);
+	a->dsize = swab32(a->dsize);
+	a->bsize = swab32(a->bsize);
+	a->entry = swab32(a->entry);
+	a->text_start = swab32(a->text_start);
+	a->data_start = swab32(a->data_start);
+	a->bss_start = swab32(a->bss_start);
+	a->gprmask = swab32(a->gprmask);
+	a->cprmask[0] = swab32(a->cprmask[0]);
+	a->cprmask[1] = swab32(a->cprmask[1]);
+	a->cprmask[2] = swab32(a->cprmask[2]);
+	a->cprmask[3] = swab32(a->cprmask[3]);
+	a->gp_value = swab32(a->gp_value);
+}
+
+static void convert_ecoff_esecs(struct scnhdr *s, int num)
+{
+	int i;
+
+	for (i = 0; i < num; i++, s++) {
+		s->s_paddr = swab32(s->s_paddr);
+		s->s_vaddr = swab32(s->s_vaddr);
+		s->s_size = swab32(s->s_size);
+		s->s_scnptr = swab32(s->s_scnptr);
+		s->s_relptr = swab32(s->s_relptr);
+		s->s_lnnoptr = swab32(s->s_lnnoptr);
+		s->s_nreloc = swab16(s->s_nreloc);
+		s->s_nlnno = swab16(s->s_nlnno);
+		s->s_flags = swab32(s->s_flags);
+	}
+}
+
+int main(int argc, char *argv[])
+{
+	Elf32_Ehdr ex;
+	Elf32_Phdr *ph;
+	Elf32_Shdr *sh;
+	int i, pad;
+	struct sect text, data, bss;
+	struct filehdr efh;
+	struct aouthdr eah;
+	struct scnhdr esecs[6];
+	int infile, outfile;
+	uint32_t cur_vma = UINT32_MAX;
+	int addflag = 0;
+	int nosecs;
+
+	text.len = data.len = bss.len = 0;
+	text.vaddr = data.vaddr = bss.vaddr = 0;
+
+	/* Check args... */
+	if (argc < 3 || argc > 4) {
+	      usage:
+		fprintf(stderr,
+			"usage: elf2ecoff <elf executable> <ecoff executable> [-a]\n");
+		exit(1);
+	}
+	if (argc == 4) {
+		if (strcmp(argv[3], "-a"))
+			goto usage;
+		addflag = 1;
+	}
+
+	/* Try the input file... */
+	if ((infile = open(argv[1], O_RDONLY)) < 0) {
+		fprintf(stderr, "Can't open %s for read: %s\n",
+			argv[1], strerror(errno));
+		exit(1);
+	}
+
+	/* Read the header, which is at the beginning of the file... */
+	i = read(infile, &ex, sizeof ex);
+	if (i != sizeof ex) {
+		fprintf(stderr, "ex: %s: %s.\n",
+			argv[1],
+			i ? strerror(errno) : "End of file reached");
+		exit(1);
+	}
+
+	if (ex.e_ident[EI_DATA] == ELFDATA2MSB)
+		format_bigendian = 1;
+
+	if (ntohs(0xaa55) == 0xaa55) {
+		if (!format_bigendian)
+			must_convert_endian = 1;
+	} else {
+		if (format_bigendian)
+			must_convert_endian = 1;
+	}
+	if (must_convert_endian)
+		convert_elf_hdr(&ex);
+
+	/* Read the program headers... */
+	ph = (Elf32_Phdr *) saveRead(infile, ex.e_phoff,
+				     ex.e_phnum * sizeof(Elf32_Phdr),
+				     "ph");
+	if (must_convert_endian)
+		convert_elf_phdrs(ph, ex.e_phnum);
+	/* Read the section headers... */
+	sh = (Elf32_Shdr *) saveRead(infile, ex.e_shoff,
+				     ex.e_shnum * sizeof(Elf32_Shdr),
+				     "sh");
+	if (must_convert_endian)
+		convert_elf_shdrs(sh, ex.e_shnum);
+
+	/* Figure out if we can cram the program header into an ECOFF
+	   header...  Basically, we can't handle anything but loadable
+	   segments, but we can ignore some kinds of segments.	We can't
+	   handle holes in the address space.  Segments may be out of order,
+	   so we sort them first. */
+
+	qsort(ph, ex.e_phnum, sizeof(Elf32_Phdr), phcmp);
+
+	for (i = 0; i < ex.e_phnum; i++) {
+		/* Section types we can ignore... */
+		switch (ph[i].p_type) {
+		case PT_NULL:
+		case PT_NOTE:
+		case PT_PHDR:
+		case PT_MIPS_REGINFO:
+		case PT_MIPS_ABIFLAGS:
+			continue;
+
+		case PT_LOAD:
+			/* Writable (data) segment? */
+			if (ph[i].p_flags & PF_W) {
+				struct sect ndata, nbss;
+
+				ndata.vaddr = ph[i].p_vaddr;
+				ndata.len = ph[i].p_filesz;
+				nbss.vaddr = ph[i].p_vaddr + ph[i].p_filesz;
+				nbss.len = ph[i].p_memsz - ph[i].p_filesz;
+
+				combine(&data, &ndata, 0);
+				combine(&bss, &nbss, 1);
+			} else {
+				struct sect ntxt;
+
+				ntxt.vaddr = ph[i].p_vaddr;
+				ntxt.len = ph[i].p_filesz;
+
+				combine(&text, &ntxt, 0);
+			}
+			/* Remember the lowest segment start address. */
+			if (ph[i].p_vaddr < cur_vma)
+				cur_vma = ph[i].p_vaddr;
+			break;
+
+		default:
+			/* Section types we can't handle... */
+			fprintf(stderr,
+				"Program header %d type %d can't be converted.\n",
+				ex.e_phnum, ph[i].p_type);
+			exit(1);
+		}
+	}
+
+	/* Sections must be in order to be converted... */
+	if (text.vaddr > data.vaddr || data.vaddr > bss.vaddr ||
+	    text.vaddr + text.len > data.vaddr
+	    || data.vaddr + data.len > bss.vaddr) {
+		fprintf(stderr,
+			"Sections ordering prevents a.out conversion.\n");
+		exit(1);
+	}
+
+	/* If there's a data section but no text section, then the loader
+	   combined everything into one section.   That needs to be the
+	   text section, so just make the data section zero length following
+	   text. */
+	if (data.len && !text.len) {
+		text = data;
+		data.vaddr = text.vaddr + text.len;
+		data.len = 0;
+	}
+
+	/* If there is a gap between text and data, we'll fill it when we copy
+	   the data, so update the length of the text segment as represented in
+	   a.out to reflect that, since a.out doesn't allow gaps in the program
+	   address space. */
+	if (text.vaddr + text.len < data.vaddr)
+		text.len = data.vaddr - text.vaddr;
+
+	/* We now have enough information to cons up an a.out header... */
+	eah.magic = OMAGIC;
+	eah.vstamp = 200;
+	eah.tsize = text.len;
+	eah.dsize = data.len;
+	eah.bsize = bss.len;
+	eah.entry = ex.e_entry;
+	eah.text_start = text.vaddr;
+	eah.data_start = data.vaddr;
+	eah.bss_start = bss.vaddr;
+	eah.gprmask = 0xf3fffffe;
+	memset(&eah.cprmask, '\0', sizeof eah.cprmask);
+	eah.gp_value = 0;	/* unused. */
+
+	if (format_bigendian)
+		efh.f_magic = MIPSEBMAGIC;
+	else
+		efh.f_magic = MIPSELMAGIC;
+	if (addflag)
+		nosecs = 6;
+	else
+		nosecs = 3;
+	efh.f_nscns = nosecs;
+	efh.f_timdat = 0;	/* bogus */
+	efh.f_symptr = 0;
+	efh.f_nsyms = 0;
+	efh.f_opthdr = sizeof eah;
+	efh.f_flags = 0x100f;	/* Stripped, not sharable. */
+
+	memset(esecs, 0, sizeof esecs);
+	strcpy(esecs[0].s_name, ".text");
+	strcpy(esecs[1].s_name, ".data");
+	strcpy(esecs[2].s_name, ".bss");
+	if (addflag) {
+		strcpy(esecs[3].s_name, ".rdata");
+		strcpy(esecs[4].s_name, ".sdata");
+		strcpy(esecs[5].s_name, ".sbss");
+	}
+	esecs[0].s_paddr = esecs[0].s_vaddr = eah.text_start;
+	esecs[1].s_paddr = esecs[1].s_vaddr = eah.data_start;
+	esecs[2].s_paddr = esecs[2].s_vaddr = eah.bss_start;
+	if (addflag) {
+		esecs[3].s_paddr = esecs[3].s_vaddr = 0;
+		esecs[4].s_paddr = esecs[4].s_vaddr = 0;
+		esecs[5].s_paddr = esecs[5].s_vaddr = 0;
+	}
+	esecs[0].s_size = eah.tsize;
+	esecs[1].s_size = eah.dsize;
+	esecs[2].s_size = eah.bsize;
+	if (addflag) {
+		esecs[3].s_size = 0;
+		esecs[4].s_size = 0;
+		esecs[5].s_size = 0;
+	}
+	esecs[0].s_scnptr = N_TXTOFF(efh, eah);
+	esecs[1].s_scnptr = N_DATOFF(efh, eah);
+#define ECOFF_SEGMENT_ALIGNMENT(a) 0x10
+#define ECOFF_ROUND(s, a) (((s)+(a)-1)&~((a)-1))
+	esecs[2].s_scnptr = esecs[1].s_scnptr +
+	    ECOFF_ROUND(esecs[1].s_size, ECOFF_SEGMENT_ALIGNMENT(&eah));
+	if (addflag) {
+		esecs[3].s_scnptr = 0;
+		esecs[4].s_scnptr = 0;
+		esecs[5].s_scnptr = 0;
+	}
+	esecs[0].s_relptr = esecs[1].s_relptr = esecs[2].s_relptr = 0;
+	esecs[0].s_lnnoptr = esecs[1].s_lnnoptr = esecs[2].s_lnnoptr = 0;
+	esecs[0].s_nreloc = esecs[1].s_nreloc = esecs[2].s_nreloc = 0;
+	esecs[0].s_nlnno = esecs[1].s_nlnno = esecs[2].s_nlnno = 0;
+	if (addflag) {
+		esecs[3].s_relptr = esecs[4].s_relptr
+		    = esecs[5].s_relptr = 0;
+		esecs[3].s_lnnoptr = esecs[4].s_lnnoptr
+		    = esecs[5].s_lnnoptr = 0;
+		esecs[3].s_nreloc = esecs[4].s_nreloc = esecs[5].s_nreloc =
+		    0;
+		esecs[3].s_nlnno = esecs[4].s_nlnno = esecs[5].s_nlnno = 0;
+	}
+	esecs[0].s_flags = 0x20;
+	esecs[1].s_flags = 0x40;
+	esecs[2].s_flags = 0x82;
+	if (addflag) {
+		esecs[3].s_flags = 0x100;
+		esecs[4].s_flags = 0x200;
+		esecs[5].s_flags = 0x400;
+	}
+
+	/* Make the output file... */
+	if ((outfile = open(argv[2], O_WRONLY | O_CREAT, 0777)) < 0) {
+		fprintf(stderr, "Unable to create %s: %s\n", argv[2],
+			strerror(errno));
+		exit(1);
+	}
+
+	if (must_convert_endian)
+		convert_ecoff_filehdr(&efh);
+	/* Write the headers... */
+	i = write(outfile, &efh, sizeof efh);
+	if (i != sizeof efh) {
+		perror("efh: write");
+		exit(1);
+
+		for (i = 0; i < nosecs; i++) {
+			printf
+			    ("Section %d: %s phys %"PRIx32"  size %"PRIx32"\t file offset %"PRIx32"\n",
+			     i, esecs[i].s_name, esecs[i].s_paddr,
+			     esecs[i].s_size, esecs[i].s_scnptr);
+		}
+	}
+	fprintf(stderr, "wrote %d byte file header.\n", i);
+
+	if (must_convert_endian)
+		convert_ecoff_aouthdr(&eah);
+	i = write(outfile, &eah, sizeof eah);
+	if (i != sizeof eah) {
+		perror("eah: write");
+		exit(1);
+	}
+	fprintf(stderr, "wrote %d byte a.out header.\n", i);
+
+	if (must_convert_endian)
+		convert_ecoff_esecs(&esecs[0], nosecs);
+	i = write(outfile, &esecs, nosecs * sizeof(struct scnhdr));
+	if (i != nosecs * sizeof(struct scnhdr)) {
+		perror("esecs: write");
+		exit(1);
+	}
+	fprintf(stderr, "wrote %d bytes of section headers.\n", i);
+
+	pad = (sizeof(efh) + sizeof(eah) + nosecs * sizeof(struct scnhdr)) & 15;
+	if (pad) {
+		pad = 16 - pad;
+		i = write(outfile, "\0\0\0\0\0\0\0\0\0\0\0\0\0\0", pad);
+		if (i < 0) {
+			perror("ipad: write");
+			exit(1);
+		}
+		fprintf(stderr, "wrote %d byte pad.\n", i);
+	}
+
+	/*
+	 * Copy the loadable sections.	 Zero-fill any gaps less than 64k;
+	 * complain about any zero-filling, and die if we're asked to zero-fill
+	 * more than 64k.
+	 */
+	for (i = 0; i < ex.e_phnum; i++) {
+		/* Unprocessable sections were handled above, so just verify that
+		   the section can be loaded before copying. */
+		if (ph[i].p_type == PT_LOAD && ph[i].p_filesz) {
+			if (cur_vma != ph[i].p_vaddr) {
+				uint32_t gap = ph[i].p_vaddr - cur_vma;
+				char obuf[1024];
+				if (gap > 65536) {
+					fprintf(stderr,
+						"Intersegment gap (%"PRId32" bytes) too large.\n",
+						gap);
+					exit(1);
+				}
+				fprintf(stderr,
+					"Warning: %d byte intersegment gap.\n",
+					gap);
+				memset(obuf, 0, sizeof obuf);
+				while (gap) {
+					int count =
+					    write(outfile, obuf,
+						  (gap >
+						   sizeof obuf ? sizeof
+						   obuf : gap));
+					if (count < 0) {
+						fprintf(stderr,
+							"Error writing gap: %s\n",
+							strerror(errno));
+						exit(1);
+					}
+					gap -= count;
+				}
+			}
+			fprintf(stderr, "writing %d bytes...\n",
+				ph[i].p_filesz);
+			copy(outfile, infile, ph[i].p_offset,
+			     ph[i].p_filesz);
+			cur_vma = ph[i].p_vaddr + ph[i].p_filesz;
+		}
+	}
+
+	/*
+	 * Write a page of padding for boot PROMS that read entire pages.
+	 * Without this, they may attempt to read past the end of the
+	 * data section, incur an error, and refuse to boot.
+	 */
+	{
+		char obuf[4096];
+		memset(obuf, 0, sizeof obuf);
+		if (write(outfile, obuf, sizeof(obuf)) != sizeof(obuf)) {
+			fprintf(stderr, "Error writing PROM padding: %s\n",
+				strerror(errno));
+			exit(1);
+		}
+	}
+
+	/* Looks like we won... */
+	exit(0);
+}
diff --git a/arch/mips/boot/tools/.gitignore b/arch/mips/boot/tools/.gitignore
new file mode 100644
index 000000000..d36dc7cf9
--- /dev/null
+++ b/arch/mips/boot/tools/.gitignore
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0-only
+relocs
diff --git a/arch/mips/boot/tools/Makefile b/arch/mips/boot/tools/Makefile
new file mode 100644
index 000000000..592e05a51
--- /dev/null
+++ b/arch/mips/boot/tools/Makefile
@@ -0,0 +1,9 @@
+# SPDX-License-Identifier: GPL-2.0
+
+hostprogs	+= relocs
+relocs-objs	+= relocs_32.o
+relocs-objs	+= relocs_64.o
+relocs-objs	+= relocs_main.o
+PHONY += relocs
+relocs: $(obj)/relocs
+	@:
diff --git a/arch/mips/boot/tools/relocs.c b/arch/mips/boot/tools/relocs.c
new file mode 100644
index 000000000..02fc85f3e
--- /dev/null
+++ b/arch/mips/boot/tools/relocs.c
@@ -0,0 +1,681 @@
+// SPDX-License-Identifier: GPL-2.0
+/* This is included from relocs_32/64.c */
+
+#define ElfW(type)		_ElfW(ELF_BITS, type)
+#define _ElfW(bits, type)	__ElfW(bits, type)
+#define __ElfW(bits, type)	Elf##bits##_##type
+
+#define Elf_Addr		ElfW(Addr)
+#define Elf_Ehdr		ElfW(Ehdr)
+#define Elf_Phdr		ElfW(Phdr)
+#define Elf_Shdr		ElfW(Shdr)
+#define Elf_Sym			ElfW(Sym)
+
+static Elf_Ehdr ehdr;
+
+struct relocs {
+	uint32_t	*offset;
+	unsigned long	count;
+	unsigned long	size;
+};
+
+static struct relocs relocs;
+
+struct section {
+	Elf_Shdr       shdr;
+	struct section *link;
+	Elf_Sym        *symtab;
+	Elf_Rel        *reltab;
+	char           *strtab;
+	long           shdr_offset;
+};
+static struct section *secs;
+
+static const char * const regex_sym_kernel = {
+/* Symbols matching these regex's should never be relocated */
+	"^(__crc_)",
+};
+
+static regex_t sym_regex_c;
+
+static int regex_skip_reloc(const char *sym_name)
+{
+	return !regexec(&sym_regex_c, sym_name, 0, NULL, 0);
+}
+
+static void regex_init(void)
+{
+	char errbuf[128];
+	int err;
+
+	err = regcomp(&sym_regex_c, regex_sym_kernel,
+			REG_EXTENDED|REG_NOSUB);
+
+	if (err) {
+		regerror(err, &sym_regex_c, errbuf, sizeof(errbuf));
+		die("%s", errbuf);
+	}
+}
+
+static const char *rel_type(unsigned type)
+{
+	static const char * const type_name[] = {
+#define REL_TYPE(X)[X] = #X
+		REL_TYPE(R_MIPS_NONE),
+		REL_TYPE(R_MIPS_16),
+		REL_TYPE(R_MIPS_32),
+		REL_TYPE(R_MIPS_REL32),
+		REL_TYPE(R_MIPS_26),
+		REL_TYPE(R_MIPS_HI16),
+		REL_TYPE(R_MIPS_LO16),
+		REL_TYPE(R_MIPS_GPREL16),
+		REL_TYPE(R_MIPS_LITERAL),
+		REL_TYPE(R_MIPS_GOT16),
+		REL_TYPE(R_MIPS_PC16),
+		REL_TYPE(R_MIPS_CALL16),
+		REL_TYPE(R_MIPS_GPREL32),
+		REL_TYPE(R_MIPS_64),
+		REL_TYPE(R_MIPS_HIGHER),
+		REL_TYPE(R_MIPS_HIGHEST),
+		REL_TYPE(R_MIPS_PC21_S2),
+		REL_TYPE(R_MIPS_PC26_S2),
+#undef REL_TYPE
+	};
+	const char *name = "unknown type rel type name";
+
+	if (type < ARRAY_SIZE(type_name) && type_name[type])
+		name = type_name[type];
+	return name;
+}
+
+static const char *sec_name(unsigned shndx)
+{
+	const char *sec_strtab;
+	const char *name;
+
+	sec_strtab = secs[ehdr.e_shstrndx].strtab;
+	if (shndx < ehdr.e_shnum)
+		name = sec_strtab + secs[shndx].shdr.sh_name;
+	else if (shndx == SHN_ABS)
+		name = "ABSOLUTE";
+	else if (shndx == SHN_COMMON)
+		name = "COMMON";
+	else
+		name = "<noname>";
+	return name;
+}
+
+static struct section *sec_lookup(const char *secname)
+{
+	int i;
+
+	for (i = 0; i < ehdr.e_shnum; i++)
+		if (strcmp(secname, sec_name(i)) == 0)
+			return &secs[i];
+
+	return NULL;
+}
+
+static const char *sym_name(const char *sym_strtab, Elf_Sym *sym)
+{
+	const char *name;
+
+	if (sym->st_name)
+		name = sym_strtab + sym->st_name;
+	else
+		name = sec_name(sym->st_shndx);
+	return name;
+}
+
+#if BYTE_ORDER == LITTLE_ENDIAN
+#define le16_to_cpu(val) (val)
+#define le32_to_cpu(val) (val)
+#define le64_to_cpu(val) (val)
+#define be16_to_cpu(val) bswap_16(val)
+#define be32_to_cpu(val) bswap_32(val)
+#define be64_to_cpu(val) bswap_64(val)
+
+#define cpu_to_le16(val) (val)
+#define cpu_to_le32(val) (val)
+#define cpu_to_le64(val) (val)
+#define cpu_to_be16(val) bswap_16(val)
+#define cpu_to_be32(val) bswap_32(val)
+#define cpu_to_be64(val) bswap_64(val)
+#endif
+#if BYTE_ORDER == BIG_ENDIAN
+#define le16_to_cpu(val) bswap_16(val)
+#define le32_to_cpu(val) bswap_32(val)
+#define le64_to_cpu(val) bswap_64(val)
+#define be16_to_cpu(val) (val)
+#define be32_to_cpu(val) (val)
+#define be64_to_cpu(val) (val)
+
+#define cpu_to_le16(val) bswap_16(val)
+#define cpu_to_le32(val) bswap_32(val)
+#define cpu_to_le64(val) bswap_64(val)
+#define cpu_to_be16(val) (val)
+#define cpu_to_be32(val) (val)
+#define cpu_to_be64(val) (val)
+#endif
+
+static uint16_t elf16_to_cpu(uint16_t val)
+{
+	if (ehdr.e_ident[EI_DATA] == ELFDATA2LSB)
+		return le16_to_cpu(val);
+	else
+		return be16_to_cpu(val);
+}
+
+static uint32_t elf32_to_cpu(uint32_t val)
+{
+	if (ehdr.e_ident[EI_DATA] == ELFDATA2LSB)
+		return le32_to_cpu(val);
+	else
+		return be32_to_cpu(val);
+}
+
+static uint32_t cpu_to_elf32(uint32_t val)
+{
+	if (ehdr.e_ident[EI_DATA] == ELFDATA2LSB)
+		return cpu_to_le32(val);
+	else
+		return cpu_to_be32(val);
+}
+
+#define elf_half_to_cpu(x)	elf16_to_cpu(x)
+#define elf_word_to_cpu(x)	elf32_to_cpu(x)
+
+#if ELF_BITS == 64
+static uint64_t elf64_to_cpu(uint64_t val)
+{
+	if (ehdr.e_ident[EI_DATA] == ELFDATA2LSB)
+		return le64_to_cpu(val);
+	else
+		return be64_to_cpu(val);
+}
+#define elf_addr_to_cpu(x)	elf64_to_cpu(x)
+#define elf_off_to_cpu(x)	elf64_to_cpu(x)
+#define elf_xword_to_cpu(x)	elf64_to_cpu(x)
+#else
+#define elf_addr_to_cpu(x)	elf32_to_cpu(x)
+#define elf_off_to_cpu(x)	elf32_to_cpu(x)
+#define elf_xword_to_cpu(x)	elf32_to_cpu(x)
+#endif
+
+static void read_ehdr(FILE *fp)
+{
+	if (fread(&ehdr, sizeof(ehdr), 1, fp) != 1)
+		die("Cannot read ELF header: %s\n", strerror(errno));
+
+	if (memcmp(ehdr.e_ident, ELFMAG, SELFMAG) != 0)
+		die("No ELF magic\n");
+
+	if (ehdr.e_ident[EI_CLASS] != ELF_CLASS)
+		die("Not a %d bit executable\n", ELF_BITS);
+
+	if ((ehdr.e_ident[EI_DATA] != ELFDATA2LSB) &&
+	    (ehdr.e_ident[EI_DATA] != ELFDATA2MSB))
+		die("Unknown ELF Endianness\n");
+
+	if (ehdr.e_ident[EI_VERSION] != EV_CURRENT)
+		die("Unknown ELF version\n");
+
+	/* Convert the fields to native endian */
+	ehdr.e_type      = elf_half_to_cpu(ehdr.e_type);
+	ehdr.e_machine   = elf_half_to_cpu(ehdr.e_machine);
+	ehdr.e_version   = elf_word_to_cpu(ehdr.e_version);
+	ehdr.e_entry     = elf_addr_to_cpu(ehdr.e_entry);
+	ehdr.e_phoff     = elf_off_to_cpu(ehdr.e_phoff);
+	ehdr.e_shoff     = elf_off_to_cpu(ehdr.e_shoff);
+	ehdr.e_flags     = elf_word_to_cpu(ehdr.e_flags);
+	ehdr.e_ehsize    = elf_half_to_cpu(ehdr.e_ehsize);
+	ehdr.e_phentsize = elf_half_to_cpu(ehdr.e_phentsize);
+	ehdr.e_phnum     = elf_half_to_cpu(ehdr.e_phnum);
+	ehdr.e_shentsize = elf_half_to_cpu(ehdr.e_shentsize);
+	ehdr.e_shnum     = elf_half_to_cpu(ehdr.e_shnum);
+	ehdr.e_shstrndx  = elf_half_to_cpu(ehdr.e_shstrndx);
+
+	if ((ehdr.e_type != ET_EXEC) && (ehdr.e_type != ET_DYN))
+		die("Unsupported ELF header type\n");
+
+	if (ehdr.e_machine != ELF_MACHINE)
+		die("Not for %s\n", ELF_MACHINE_NAME);
+
+	if (ehdr.e_version != EV_CURRENT)
+		die("Unknown ELF version\n");
+
+	if (ehdr.e_ehsize != sizeof(Elf_Ehdr))
+		die("Bad Elf header size\n");
+
+	if (ehdr.e_phentsize != sizeof(Elf_Phdr))
+		die("Bad program header entry\n");
+
+	if (ehdr.e_shentsize != sizeof(Elf_Shdr))
+		die("Bad section header entry\n");
+
+	if (ehdr.e_shstrndx >= ehdr.e_shnum)
+		die("String table index out of bounds\n");
+}
+
+static void read_shdrs(FILE *fp)
+{
+	int i;
+	Elf_Shdr shdr;
+
+	secs = calloc(ehdr.e_shnum, sizeof(struct section));
+	if (!secs)
+		die("Unable to allocate %d section headers\n", ehdr.e_shnum);
+
+	if (fseek(fp, ehdr.e_shoff, SEEK_SET) < 0)
+		die("Seek to %d failed: %s\n", ehdr.e_shoff, strerror(errno));
+
+	for (i = 0; i < ehdr.e_shnum; i++) {
+		struct section *sec = &secs[i];
+
+		sec->shdr_offset = ftell(fp);
+		if (fread(&shdr, sizeof(shdr), 1, fp) != 1)
+			die("Cannot read ELF section headers %d/%d: %s\n",
+			    i, ehdr.e_shnum, strerror(errno));
+		sec->shdr.sh_name      = elf_word_to_cpu(shdr.sh_name);
+		sec->shdr.sh_type      = elf_word_to_cpu(shdr.sh_type);
+		sec->shdr.sh_flags     = elf_xword_to_cpu(shdr.sh_flags);
+		sec->shdr.sh_addr      = elf_addr_to_cpu(shdr.sh_addr);
+		sec->shdr.sh_offset    = elf_off_to_cpu(shdr.sh_offset);
+		sec->shdr.sh_size      = elf_xword_to_cpu(shdr.sh_size);
+		sec->shdr.sh_link      = elf_word_to_cpu(shdr.sh_link);
+		sec->shdr.sh_info      = elf_word_to_cpu(shdr.sh_info);
+		sec->shdr.sh_addralign = elf_xword_to_cpu(shdr.sh_addralign);
+		sec->shdr.sh_entsize   = elf_xword_to_cpu(shdr.sh_entsize);
+		if (sec->shdr.sh_link < ehdr.e_shnum)
+			sec->link = &secs[sec->shdr.sh_link];
+	}
+}
+
+static void read_strtabs(FILE *fp)
+{
+	int i;
+
+	for (i = 0; i < ehdr.e_shnum; i++) {
+		struct section *sec = &secs[i];
+
+		if (sec->shdr.sh_type != SHT_STRTAB)
+			continue;
+
+		sec->strtab = malloc(sec->shdr.sh_size);
+		if (!sec->strtab)
+			die("malloc of %d bytes for strtab failed\n",
+			    sec->shdr.sh_size);
+
+		if (fseek(fp, sec->shdr.sh_offset, SEEK_SET) < 0)
+			die("Seek to %d failed: %s\n",
+			    sec->shdr.sh_offset, strerror(errno));
+
+		if (fread(sec->strtab, 1, sec->shdr.sh_size, fp) !=
+		    sec->shdr.sh_size)
+			die("Cannot read symbol table: %s\n", strerror(errno));
+	}
+}
+
+static void read_symtabs(FILE *fp)
+{
+	int i, j;
+
+	for (i = 0; i < ehdr.e_shnum; i++) {
+		struct section *sec = &secs[i];
+		if (sec->shdr.sh_type != SHT_SYMTAB)
+			continue;
+
+		sec->symtab = malloc(sec->shdr.sh_size);
+		if (!sec->symtab)
+			die("malloc of %d bytes for symtab failed\n",
+			    sec->shdr.sh_size);
+
+		if (fseek(fp, sec->shdr.sh_offset, SEEK_SET) < 0)
+			die("Seek to %d failed: %s\n",
+			    sec->shdr.sh_offset, strerror(errno));
+
+		if (fread(sec->symtab, 1, sec->shdr.sh_size, fp) !=
+		    sec->shdr.sh_size)
+			die("Cannot read symbol table: %s\n", strerror(errno));
+
+		for (j = 0; j < sec->shdr.sh_size/sizeof(Elf_Sym); j++) {
+			Elf_Sym *sym = &sec->symtab[j];
+
+			sym->st_name  = elf_word_to_cpu(sym->st_name);
+			sym->st_value = elf_addr_to_cpu(sym->st_value);
+			sym->st_size  = elf_xword_to_cpu(sym->st_size);
+			sym->st_shndx = elf_half_to_cpu(sym->st_shndx);
+		}
+	}
+}
+
+static void read_relocs(FILE *fp)
+{
+	static unsigned long base;
+	int i, j;
+
+	if (!base) {
+		struct section *sec = sec_lookup(".text");
+
+		if (!sec)
+			die("Could not find .text section\n");
+
+		base = sec->shdr.sh_addr;
+	}
+
+	for (i = 0; i < ehdr.e_shnum; i++) {
+		struct section *sec = &secs[i];
+
+		if (sec->shdr.sh_type != SHT_REL_TYPE)
+			continue;
+
+		sec->reltab = malloc(sec->shdr.sh_size);
+		if (!sec->reltab)
+			die("malloc of %d bytes for relocs failed\n",
+			    sec->shdr.sh_size);
+
+		if (fseek(fp, sec->shdr.sh_offset, SEEK_SET) < 0)
+			die("Seek to %d failed: %s\n",
+			    sec->shdr.sh_offset, strerror(errno));
+
+		if (fread(sec->reltab, 1, sec->shdr.sh_size, fp) !=
+		    sec->shdr.sh_size)
+			die("Cannot read symbol table: %s\n", strerror(errno));
+
+		for (j = 0; j < sec->shdr.sh_size/sizeof(Elf_Rel); j++) {
+			Elf_Rel *rel = &sec->reltab[j];
+
+			rel->r_offset = elf_addr_to_cpu(rel->r_offset);
+			/* Set offset into kernel image */
+			rel->r_offset -= base;
+#if (ELF_BITS == 32)
+			rel->r_info   = elf_xword_to_cpu(rel->r_info);
+#else
+			/* Convert MIPS64 RELA format - only the symbol
+			 * index needs converting to native endianness
+			 */
+			rel->r_info   = rel->r_info;
+			ELF_R_SYM(rel->r_info) = elf32_to_cpu(ELF_R_SYM(rel->r_info));
+#endif
+#if (SHT_REL_TYPE == SHT_RELA)
+			rel->r_addend = elf_xword_to_cpu(rel->r_addend);
+#endif
+		}
+	}
+}
+
+static void remove_relocs(FILE *fp)
+{
+	int i;
+	Elf_Shdr shdr;
+
+	for (i = 0; i < ehdr.e_shnum; i++) {
+		struct section *sec = &secs[i];
+
+		if (sec->shdr.sh_type != SHT_REL_TYPE)
+			continue;
+
+		if (fseek(fp, sec->shdr_offset, SEEK_SET) < 0)
+			die("Seek to %d failed: %s\n",
+			    sec->shdr_offset, strerror(errno));
+
+		if (fread(&shdr, sizeof(shdr), 1, fp) != 1)
+			die("Cannot read ELF section headers %d/%d: %s\n",
+			    i, ehdr.e_shnum, strerror(errno));
+
+		/* Set relocation section size to 0, effectively removing it.
+		 * This is necessary due to lack of support for relocations
+		 * in objcopy when creating 32bit elf from 64bit elf.
+		 */
+		shdr.sh_size = 0;
+
+		if (fseek(fp, sec->shdr_offset, SEEK_SET) < 0)
+			die("Seek to %d failed: %s\n",
+			    sec->shdr_offset, strerror(errno));
+
+		if (fwrite(&shdr, sizeof(shdr), 1, fp) != 1)
+			die("Cannot write ELF section headers %d/%d: %s\n",
+			    i, ehdr.e_shnum, strerror(errno));
+	}
+}
+
+static void add_reloc(struct relocs *r, uint32_t offset, unsigned type)
+{
+	/* Relocation representation in binary table:
+	 * |76543210|76543210|76543210|76543210|
+	 * |  Type  |  offset from _text >> 2  |
+	 */
+	offset >>= 2;
+	if (offset > 0x00FFFFFF)
+		die("Kernel image exceeds maximum size for relocation!\n");
+
+	offset = (offset & 0x00FFFFFF) | ((type & 0xFF) << 24);
+
+	if (r->count == r->size) {
+		unsigned long newsize = r->size + 50000;
+		void *mem = realloc(r->offset, newsize * sizeof(r->offset[0]));
+
+		if (!mem)
+			die("realloc failed\n");
+
+		r->offset = mem;
+		r->size = newsize;
+	}
+	r->offset[r->count++] = offset;
+}
+
+static void walk_relocs(int (*process)(struct section *sec, Elf_Rel *rel,
+			Elf_Sym *sym, const char *symname))
+{
+	int i;
+
+	/* Walk through the relocations */
+	for (i = 0; i < ehdr.e_shnum; i++) {
+		char *sym_strtab;
+		Elf_Sym *sh_symtab;
+		struct section *sec_applies, *sec_symtab;
+		int j;
+		struct section *sec = &secs[i];
+
+		if (sec->shdr.sh_type != SHT_REL_TYPE)
+			continue;
+
+		sec_symtab  = sec->link;
+		sec_applies = &secs[sec->shdr.sh_info];
+		if (!(sec_applies->shdr.sh_flags & SHF_ALLOC))
+			continue;
+
+		sh_symtab = sec_symtab->symtab;
+		sym_strtab = sec_symtab->link->strtab;
+		for (j = 0; j < sec->shdr.sh_size/sizeof(Elf_Rel); j++) {
+			Elf_Rel *rel = &sec->reltab[j];
+			Elf_Sym *sym = &sh_symtab[ELF_R_SYM(rel->r_info)];
+			const char *symname = sym_name(sym_strtab, sym);
+
+			process(sec, rel, sym, symname);
+		}
+	}
+}
+
+static int do_reloc(struct section *sec, Elf_Rel *rel, Elf_Sym *sym,
+		      const char *symname)
+{
+	unsigned r_type = ELF_R_TYPE(rel->r_info);
+	unsigned bind = ELF_ST_BIND(sym->st_info);
+
+	if ((bind == STB_WEAK) && (sym->st_value == 0)) {
+		/* Don't relocate weak symbols without a target */
+		return 0;
+	}
+
+	if (regex_skip_reloc(symname))
+		return 0;
+
+	switch (r_type) {
+	case R_MIPS_NONE:
+	case R_MIPS_REL32:
+	case R_MIPS_PC16:
+	case R_MIPS_PC21_S2:
+	case R_MIPS_PC26_S2:
+		/*
+		 * NONE can be ignored and PC relative relocations don't
+		 * need to be adjusted.
+		 */
+	case R_MIPS_HIGHEST:
+	case R_MIPS_HIGHER:
+		/* We support relocating within the same 4Gb segment only,
+		 * thus leaving the top 32bits unchanged
+		 */
+	case R_MIPS_LO16:
+		/* We support relocating by 64k jumps only
+		 * thus leaving the bottom 16bits unchanged
+		 */
+		break;
+
+	case R_MIPS_64:
+	case R_MIPS_32:
+	case R_MIPS_26:
+	case R_MIPS_HI16:
+		add_reloc(&relocs, rel->r_offset, r_type);
+		break;
+
+	default:
+		die("Unsupported relocation type: %s (%d)\n",
+		    rel_type(r_type), r_type);
+		break;
+	}
+
+	return 0;
+}
+
+static int write_reloc_as_bin(uint32_t v, FILE *f)
+{
+	unsigned char buf[4];
+
+	v = cpu_to_elf32(v);
+
+	memcpy(buf, &v, sizeof(uint32_t));
+	return fwrite(buf, 1, 4, f);
+}
+
+static int write_reloc_as_text(uint32_t v, FILE *f)
+{
+	int res;
+
+	res = fprintf(f, "\t.long 0x%08"PRIx32"\n", v);
+	if (res < 0)
+		return res;
+	else
+		return sizeof(uint32_t);
+}
+
+static void emit_relocs(int as_text, int as_bin, FILE *outf)
+{
+	int i;
+	int (*write_reloc)(uint32_t, FILE *) = write_reloc_as_bin;
+	int size = 0;
+	int size_reserved;
+	struct section *sec_reloc;
+
+	sec_reloc = sec_lookup(".data.reloc");
+	if (!sec_reloc)
+		die("Could not find relocation section\n");
+
+	size_reserved = sec_reloc->shdr.sh_size;
+
+	/* Collect up the relocations */
+	walk_relocs(do_reloc);
+
+	/* Print the relocations */
+	if (as_text) {
+		/* Print the relocations in a form suitable that
+		 * gas will like.
+		 */
+		printf(".section \".data.reloc\",\"a\"\n");
+		printf(".balign 4\n");
+		/* Output text to stdout */
+		write_reloc = write_reloc_as_text;
+		outf = stdout;
+	} else if (as_bin) {
+		/* Output raw binary to stdout */
+		outf = stdout;
+	} else {
+		/* Seek to offset of the relocation section.
+		* Each relocation is then written into the
+		* vmlinux kernel image.
+		*/
+		if (fseek(outf, sec_reloc->shdr.sh_offset, SEEK_SET) < 0) {
+			die("Seek to %d failed: %s\n",
+				sec_reloc->shdr.sh_offset, strerror(errno));
+		}
+	}
+
+	for (i = 0; i < relocs.count; i++)
+		size += write_reloc(relocs.offset[i], outf);
+
+	/* Print a stop, but only if we've actually written some relocs */
+	if (size)
+		size += write_reloc(0, outf);
+
+	if (size > size_reserved)
+		/* Die, but suggest a value for CONFIG_RELOCATION_TABLE_SIZE
+		 * which will fix this problem and allow a bit of headroom
+		 * if more kernel features are enabled
+		 */
+		die("Relocations overflow available space!\n" \
+		    "Please adjust CONFIG_RELOCATION_TABLE_SIZE " \
+		    "to at least 0x%08x\n", (size + 0x1000) & ~0xFFF);
+}
+
+/*
+ * As an aid to debugging problems with different linkers
+ * print summary information about the relocs.
+ * Since different linkers tend to emit the sections in
+ * different orders we use the section names in the output.
+ */
+static int do_reloc_info(struct section *sec, Elf_Rel *rel, ElfW(Sym) *sym,
+				const char *symname)
+{
+	printf("%16s  0x%08x  %16s  %40s  %16s\n",
+		sec_name(sec->shdr.sh_info),
+		(unsigned int)rel->r_offset,
+		rel_type(ELF_R_TYPE(rel->r_info)),
+		symname,
+		sec_name(sym->st_shndx));
+	return 0;
+}
+
+static void print_reloc_info(void)
+{
+	printf("%16s  %10s  %16s  %40s  %16s\n",
+		"reloc section",
+		"offset",
+		"reloc type",
+		"symbol",
+		"symbol section");
+	walk_relocs(do_reloc_info);
+}
+
+#if ELF_BITS == 64
+# define process process_64
+#else
+# define process process_32
+#endif
+
+void process(FILE *fp, int as_text, int as_bin,
+	     int show_reloc_info, int keep_relocs)
+{
+	regex_init();
+	read_ehdr(fp);
+	read_shdrs(fp);
+	read_strtabs(fp);
+	read_symtabs(fp);
+	read_relocs(fp);
+	if (show_reloc_info) {
+		print_reloc_info();
+		return;
+	}
+	emit_relocs(as_text, as_bin, fp);
+	if (!keep_relocs)
+		remove_relocs(fp);
+}
diff --git a/arch/mips/boot/tools/relocs.h b/arch/mips/boot/tools/relocs.h
new file mode 100644
index 000000000..607ff0103
--- /dev/null
+++ b/arch/mips/boot/tools/relocs.h
@@ -0,0 +1,46 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef RELOCS_H
+#define RELOCS_H
+
+#include <stdio.h>
+#include <stdarg.h>
+#include <stdlib.h>
+#include <stdint.h>
+#include <inttypes.h>
+#include <string.h>
+#include <errno.h>
+#include <unistd.h>
+#include <elf.h>
+#include <byteswap.h>
+#define USE_BSD
+#include <endian.h>
+#include <regex.h>
+
+void die(char *fmt, ...);
+
+/*
+ * Introduced for MIPSr6
+ */
+#ifndef R_MIPS_PC21_S2
+#define R_MIPS_PC21_S2		60
+#endif
+
+#ifndef R_MIPS_PC26_S2
+#define R_MIPS_PC26_S2		61
+#endif
+
+#define ARRAY_SIZE(x) (sizeof(x) / sizeof((x)[0]))
+
+enum symtype {
+	S_ABS,
+	S_REL,
+	S_SEG,
+	S_LIN,
+	S_NSYMTYPES
+};
+
+void process_32(FILE *fp, int as_text, int as_bin,
+		int show_reloc_info, int keep_relocs);
+void process_64(FILE *fp, int as_text, int as_bin,
+		int show_reloc_info, int keep_relocs);
+#endif /* RELOCS_H */
diff --git a/arch/mips/boot/tools/relocs_32.c b/arch/mips/boot/tools/relocs_32.c
new file mode 100644
index 000000000..428bea489
--- /dev/null
+++ b/arch/mips/boot/tools/relocs_32.c
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "relocs.h"
+
+#define ELF_BITS 32
+
+#define ELF_MACHINE		EM_MIPS
+#define ELF_MACHINE_NAME	"MIPS"
+#define SHT_REL_TYPE		SHT_REL
+#define Elf_Rel			ElfW(Rel)
+
+#define ELF_CLASS		ELFCLASS32
+#define ELF_R_SYM(val)		ELF32_R_SYM(val)
+#define ELF_R_TYPE(val)		ELF32_R_TYPE(val)
+#define ELF_ST_TYPE(o)		ELF32_ST_TYPE(o)
+#define ELF_ST_BIND(o)		ELF32_ST_BIND(o)
+#define ELF_ST_VISIBILITY(o)	ELF32_ST_VISIBILITY(o)
+
+#include "relocs.c"
diff --git a/arch/mips/boot/tools/relocs_64.c b/arch/mips/boot/tools/relocs_64.c
new file mode 100644
index 000000000..154015d74
--- /dev/null
+++ b/arch/mips/boot/tools/relocs_64.c
@@ -0,0 +1,31 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "relocs.h"
+
+#define ELF_BITS 64
+
+#define ELF_MACHINE             EM_MIPS
+#define ELF_MACHINE_NAME        "MIPS64"
+#define SHT_REL_TYPE            SHT_RELA
+#define Elf_Rel                 Elf64_Rela
+
+typedef uint8_t Elf64_Byte;
+
+typedef union {
+	struct {
+		Elf64_Word r_sym;	/* Symbol index.  */
+		Elf64_Byte r_ssym;	/* Special symbol.  */
+		Elf64_Byte r_type3;	/* Third relocation.  */
+		Elf64_Byte r_type2;	/* Second relocation.  */
+		Elf64_Byte r_type;	/* First relocation.  */
+	} fields;
+	Elf64_Xword unused;
+} Elf64_Mips_Rela;
+
+#define ELF_CLASS               ELFCLASS64
+#define ELF_R_SYM(val)          (((Elf64_Mips_Rela *)(&val))->fields.r_sym)
+#define ELF_R_TYPE(val)         (((Elf64_Mips_Rela *)(&val))->fields.r_type)
+#define ELF_ST_TYPE(o)          ELF64_ST_TYPE(o)
+#define ELF_ST_BIND(o)          ELF64_ST_BIND(o)
+#define ELF_ST_VISIBILITY(o)    ELF64_ST_VISIBILITY(o)
+
+#include "relocs.c"
diff --git a/arch/mips/boot/tools/relocs_main.c b/arch/mips/boot/tools/relocs_main.c
new file mode 100644
index 000000000..e2453a564
--- /dev/null
+++ b/arch/mips/boot/tools/relocs_main.c
@@ -0,0 +1,85 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include <stdio.h>
+#include <stdint.h>
+#include <stdarg.h>
+#include <stdlib.h>
+#include <string.h>
+#include <errno.h>
+#include <endian.h>
+#include <elf.h>
+
+#include "relocs.h"
+
+void die(char *fmt, ...)
+{
+	va_list ap;
+
+	va_start(ap, fmt);
+	vfprintf(stderr, fmt, ap);
+	va_end(ap);
+	exit(1);
+}
+
+static void usage(void)
+{
+	die("relocs [--reloc-info|--text|--bin|--keep] vmlinux\n");
+}
+
+int main(int argc, char **argv)
+{
+	int show_reloc_info, as_text, as_bin, keep_relocs;
+	const char *fname;
+	FILE *fp;
+	int i;
+	unsigned char e_ident[EI_NIDENT];
+
+	show_reloc_info = 0;
+	as_text = 0;
+	as_bin = 0;
+	keep_relocs = 0;
+	fname = NULL;
+	for (i = 1; i < argc; i++) {
+		char *arg = argv[i];
+
+		if (*arg == '-') {
+			if (strcmp(arg, "--reloc-info") == 0) {
+				show_reloc_info = 1;
+				continue;
+			}
+			if (strcmp(arg, "--text") == 0) {
+				as_text = 1;
+				continue;
+			}
+			if (strcmp(arg, "--bin") == 0) {
+				as_bin = 1;
+				continue;
+			}
+			if (strcmp(arg, "--keep") == 0) {
+				keep_relocs = 1;
+				continue;
+			}
+		} else if (!fname) {
+			fname = arg;
+			continue;
+		}
+		usage();
+	}
+	if (!fname)
+		usage();
+
+	fp = fopen(fname, "r+");
+	if (!fp)
+		die("Cannot open %s: %s\n", fname, strerror(errno));
+
+	if (fread(&e_ident, 1, EI_NIDENT, fp) != EI_NIDENT)
+		die("Cannot read %s: %s", fname, strerror(errno));
+
+	rewind(fp);
+	if (e_ident[EI_CLASS] == ELFCLASS64)
+		process_64(fp, as_text,  as_bin, show_reloc_info, keep_relocs);
+	else
+		process_32(fp, as_text, as_bin, show_reloc_info, keep_relocs);
+	fclose(fp);
+	return 0;
+}
diff --git a/arch/mips/cavium-octeon/Kconfig b/arch/mips/cavium-octeon/Kconfig
new file mode 100644
index 000000000..c1899f109
--- /dev/null
+++ b/arch/mips/cavium-octeon/Kconfig
@@ -0,0 +1,91 @@
+# SPDX-License-Identifier: GPL-2.0
+if CPU_CAVIUM_OCTEON
+
+config CAVIUM_CN63XXP1
+	bool "Enable CN63XXP1 errata workarounds"
+	default "n"
+	help
+	  The CN63XXP1 chip requires build time workarounds to
+	  function reliably, select this option to enable them.  These
+	  workarounds will cause a slight decrease in performance on
+	  non-CN63XXP1 hardware, so it is recommended to select "n"
+	  unless it is known the workarounds are needed.
+
+config CAVIUM_OCTEON_CVMSEG_SIZE
+	int "Number of L1 cache lines reserved for CVMSEG memory"
+	range 0 54
+	default 1
+	help
+	  CVMSEG LM is a segment that accesses portions of the dcache as a
+	  local memory; the larger CVMSEG is, the smaller the cache is.
+	  This selects the size of CVMSEG LM, which is in cache blocks. The
+	  legally range is from zero to 54 cache blocks (i.e. CVMSEG LM is
+	  between zero and 6192 bytes).
+
+endif # CPU_CAVIUM_OCTEON
+
+if CAVIUM_OCTEON_SOC
+
+config CAVIUM_OCTEON_LOCK_L2
+	bool "Lock often used kernel code in the L2"
+	default "y"
+	help
+	  Enable locking parts of the kernel into the L2 cache.
+
+config CAVIUM_OCTEON_LOCK_L2_TLB
+	bool "Lock the TLB handler in L2"
+	depends on CAVIUM_OCTEON_LOCK_L2
+	default "y"
+	help
+	  Lock the low level TLB fast path into L2.
+
+config CAVIUM_OCTEON_LOCK_L2_EXCEPTION
+	bool "Lock the exception handler in L2"
+	depends on CAVIUM_OCTEON_LOCK_L2
+	default "y"
+	help
+	  Lock the low level exception handler into L2.
+
+config CAVIUM_OCTEON_LOCK_L2_LOW_LEVEL_INTERRUPT
+	bool "Lock the interrupt handler in L2"
+	depends on CAVIUM_OCTEON_LOCK_L2
+	default "y"
+	help
+	  Lock the low level interrupt handler into L2.
+
+config CAVIUM_OCTEON_LOCK_L2_INTERRUPT
+	bool "Lock the 2nd level interrupt handler in L2"
+	depends on CAVIUM_OCTEON_LOCK_L2
+	default "y"
+	help
+	  Lock the 2nd level interrupt handler in L2.
+
+config CAVIUM_OCTEON_LOCK_L2_MEMCPY
+	bool "Lock memcpy() in L2"
+	depends on CAVIUM_OCTEON_LOCK_L2
+	default "y"
+	help
+	  Lock the kernel's implementation of memcpy() into L2.
+
+config CAVIUM_RESERVE32
+	int "Memory to reserve for user processes shared region (MB)"
+	range 0 1536
+	default "0"
+	help
+	  Reserve a shared memory region for user processes to use for hardware
+	  memory buffers. This is required for 32bit applications to be able to
+	  send and receive packets directly. Applications access this memory by
+	  memory mapping /dev/mem for the addresses in /proc/octeon_info. For
+	  optimal performance with HugeTLBs, keep this size an even number of
+	  megabytes.
+
+config OCTEON_ILM
+	tristate "Module to measure interrupt latency using Octeon CIU Timer"
+	help
+	  This driver is a module to measure interrupt latency using the
+	  the CIU Timers on Octeon.
+
+	  To compile this driver as a module, choose M here.  The module
+	  will be called octeon-ilm
+
+endif # CAVIUM_OCTEON_SOC
diff --git a/arch/mips/cavium-octeon/Makefile b/arch/mips/cavium-octeon/Makefile
new file mode 100644
index 000000000..7c02e5429
--- /dev/null
+++ b/arch/mips/cavium-octeon/Makefile
@@ -0,0 +1,21 @@
+#
+# Makefile for the Cavium Octeon specific kernel interface routines
+# under Linux.
+#
+# This file is subject to the terms and conditions of the GNU General Public
+# License.  See the file "COPYING" in the main directory of this archive
+# for more details.
+#
+# Copyright (C) 2005-2009 Cavium Networks
+#
+
+obj-y := cpu.o setup.o octeon-platform.o octeon-irq.o csrc-octeon.o
+obj-y += dma-octeon.o
+obj-y += octeon-memcpy.o
+obj-y += executive/
+obj-y += crypto/
+
+obj-$(CONFIG_MTD)		      += flash_setup.o
+obj-$(CONFIG_SMP)		      += smp.o
+obj-$(CONFIG_OCTEON_ILM)	      += oct_ilm.o
+obj-$(CONFIG_USB)		      += octeon-usb.o
diff --git a/arch/mips/cavium-octeon/Platform b/arch/mips/cavium-octeon/Platform
new file mode 100644
index 000000000..4adef38de
--- /dev/null
+++ b/arch/mips/cavium-octeon/Platform
@@ -0,0 +1,6 @@
+#
+# Cavium Octeon
+#
+cflags-$(CONFIG_CAVIUM_OCTEON_SOC)	+=				\
+		-I$(srctree)/arch/mips/include/asm/mach-cavium-octeon
+load-$(CONFIG_CAVIUM_OCTEON_SOC)	+= 0xffffffff81100000
diff --git a/arch/mips/cavium-octeon/cpu.c b/arch/mips/cavium-octeon/cpu.c
new file mode 100644
index 000000000..036d56cc4
--- /dev/null
+++ b/arch/mips/cavium-octeon/cpu.c
@@ -0,0 +1,50 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2009 Wind River Systems,
+ *   written by Ralf Baechle <ralf@linux-mips.org>
+ */
+#include <linux/init.h>
+#include <linux/irqflags.h>
+#include <linux/notifier.h>
+#include <linux/prefetch.h>
+#include <linux/ptrace.h>
+#include <linux/sched.h>
+#include <linux/sched/task_stack.h>
+
+#include <asm/cop2.h>
+#include <asm/current.h>
+#include <asm/mipsregs.h>
+#include <asm/page.h>
+#include <asm/octeon/octeon.h>
+
+static int cnmips_cu2_call(struct notifier_block *nfb, unsigned long action,
+	void *data)
+{
+	unsigned long flags;
+	unsigned int status;
+
+	switch (action) {
+	case CU2_EXCEPTION:
+		prefetch(&current->thread.cp2);
+		local_irq_save(flags);
+		KSTK_STATUS(current) |= ST0_CU2;
+		status = read_c0_status();
+		write_c0_status(status | ST0_CU2);
+		octeon_cop2_restore(&(current->thread.cp2));
+		write_c0_status(status & ~ST0_CU2);
+		local_irq_restore(flags);
+
+		return NOTIFY_BAD;	/* Don't call default notifier */
+	}
+
+	return NOTIFY_OK;		/* Let default notifier send signals */
+}
+
+static int __init cnmips_cu2_setup(void)
+{
+	return cu2_notifier(cnmips_cu2_call, 0);
+}
+early_initcall(cnmips_cu2_setup);
diff --git a/arch/mips/cavium-octeon/crypto/Makefile b/arch/mips/cavium-octeon/crypto/Makefile
new file mode 100644
index 000000000..db26c73fa
--- /dev/null
+++ b/arch/mips/cavium-octeon/crypto/Makefile
@@ -0,0 +1,11 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# OCTEON-specific crypto modules.
+#
+
+obj-y += octeon-crypto.o
+
+obj-$(CONFIG_CRYPTO_MD5_OCTEON)		+= octeon-md5.o
+obj-$(CONFIG_CRYPTO_SHA1_OCTEON)	+= octeon-sha1.o
+obj-$(CONFIG_CRYPTO_SHA256_OCTEON)	+= octeon-sha256.o
+obj-$(CONFIG_CRYPTO_SHA512_OCTEON)	+= octeon-sha512.o
diff --git a/arch/mips/cavium-octeon/crypto/octeon-crypto.c b/arch/mips/cavium-octeon/crypto/octeon-crypto.c
new file mode 100644
index 000000000..cfb4a146c
--- /dev/null
+++ b/arch/mips/cavium-octeon/crypto/octeon-crypto.c
@@ -0,0 +1,69 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2004-2012 Cavium Networks
+ */
+
+#include <asm/cop2.h>
+#include <linux/export.h>
+#include <linux/interrupt.h>
+#include <linux/sched/task_stack.h>
+
+#include "octeon-crypto.h"
+
+/**
+ * Enable access to Octeon's COP2 crypto hardware for kernel use. Wrap any
+ * crypto operations in calls to octeon_crypto_enable/disable in order to make
+ * sure the state of COP2 isn't corrupted if userspace is also performing
+ * hardware crypto operations. Allocate the state parameter on the stack.
+ * Returns with preemption disabled.
+ *
+ * @state: Pointer to state structure to store current COP2 state in.
+ *
+ * Returns: Flags to be passed to octeon_crypto_disable()
+ */
+unsigned long octeon_crypto_enable(struct octeon_cop2_state *state)
+{
+	int status;
+	unsigned long flags;
+
+	preempt_disable();
+	local_irq_save(flags);
+	status = read_c0_status();
+	write_c0_status(status | ST0_CU2);
+	if (KSTK_STATUS(current) & ST0_CU2) {
+		octeon_cop2_save(&(current->thread.cp2));
+		KSTK_STATUS(current) &= ~ST0_CU2;
+		status &= ~ST0_CU2;
+	} else if (status & ST0_CU2) {
+		octeon_cop2_save(state);
+	}
+	local_irq_restore(flags);
+	return status & ST0_CU2;
+}
+EXPORT_SYMBOL_GPL(octeon_crypto_enable);
+
+/**
+ * Disable access to Octeon's COP2 crypto hardware in the kernel. This must be
+ * called after an octeon_crypto_enable() before any context switch or return to
+ * userspace.
+ *
+ * @state:	Pointer to COP2 state to restore
+ * @flags:	Return value from octeon_crypto_enable()
+ */
+void octeon_crypto_disable(struct octeon_cop2_state *state,
+			   unsigned long crypto_flags)
+{
+	unsigned long flags;
+
+	local_irq_save(flags);
+	if (crypto_flags & ST0_CU2)
+		octeon_cop2_restore(state);
+	else
+		write_c0_status(read_c0_status() & ~ST0_CU2);
+	local_irq_restore(flags);
+	preempt_enable();
+}
+EXPORT_SYMBOL_GPL(octeon_crypto_disable);
diff --git a/arch/mips/cavium-octeon/crypto/octeon-crypto.h b/arch/mips/cavium-octeon/crypto/octeon-crypto.h
new file mode 100644
index 000000000..cb68f9e28
--- /dev/null
+++ b/arch/mips/cavium-octeon/crypto/octeon-crypto.h
@@ -0,0 +1,224 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2012-2013 Cavium Inc., All Rights Reserved.
+ *
+ * MD5/SHA1/SHA256/SHA512 instruction definitions added by
+ * Aaro Koskinen <aaro.koskinen@iki.fi>.
+ *
+ */
+#ifndef __LINUX_OCTEON_CRYPTO_H
+#define __LINUX_OCTEON_CRYPTO_H
+
+#include <linux/sched.h>
+#include <asm/mipsregs.h>
+
+#define OCTEON_CR_OPCODE_PRIORITY 300
+
+extern unsigned long octeon_crypto_enable(struct octeon_cop2_state *state);
+extern void octeon_crypto_disable(struct octeon_cop2_state *state,
+				  unsigned long flags);
+
+/*
+ * Macros needed to implement MD5/SHA1/SHA256:
+ */
+
+/*
+ * The index can be 0-1 (MD5) or 0-2 (SHA1), 0-3 (SHA256).
+ */
+#define write_octeon_64bit_hash_dword(value, index)	\
+do {							\
+	__asm__ __volatile__ (				\
+	"dmtc2 %[rt],0x0048+" STR(index)		\
+	:						\
+	: [rt] "d" (cpu_to_be64(value)));		\
+} while (0)
+
+/*
+ * The index can be 0-1 (MD5) or 0-2 (SHA1), 0-3 (SHA256).
+ */
+#define read_octeon_64bit_hash_dword(index)		\
+({							\
+	__be64 __value;					\
+							\
+	__asm__ __volatile__ (				\
+	"dmfc2 %[rt],0x0048+" STR(index)		\
+	: [rt] "=d" (__value)				\
+	: );						\
+							\
+	be64_to_cpu(__value);				\
+})
+
+/*
+ * The index can be 0-6.
+ */
+#define write_octeon_64bit_block_dword(value, index)	\
+do {							\
+	__asm__ __volatile__ (				\
+	"dmtc2 %[rt],0x0040+" STR(index)		\
+	:						\
+	: [rt] "d" (cpu_to_be64(value)));		\
+} while (0)
+
+/*
+ * The value is the final block dword (64-bit).
+ */
+#define octeon_md5_start(value)				\
+do {							\
+	__asm__ __volatile__ (				\
+	"dmtc2 %[rt],0x4047"				\
+	:						\
+	: [rt] "d" (cpu_to_be64(value)));		\
+} while (0)
+
+/*
+ * The value is the final block dword (64-bit).
+ */
+#define octeon_sha1_start(value)			\
+do {							\
+	__asm__ __volatile__ (				\
+	"dmtc2 %[rt],0x4057"				\
+	:						\
+	: [rt] "d" (value));				\
+} while (0)
+
+/*
+ * The value is the final block dword (64-bit).
+ */
+#define octeon_sha256_start(value)			\
+do {							\
+	__asm__ __volatile__ (				\
+	"dmtc2 %[rt],0x404f"				\
+	:						\
+	: [rt] "d" (value));				\
+} while (0)
+
+/*
+ * Macros needed to implement SHA512:
+ */
+
+/*
+ * The index can be 0-7.
+ */
+#define write_octeon_64bit_hash_sha512(value, index)	\
+do {							\
+	__asm__ __volatile__ (				\
+	"dmtc2 %[rt],0x0250+" STR(index)		\
+	:						\
+	: [rt] "d" (value));				\
+} while (0)
+
+/*
+ * The index can be 0-7.
+ */
+#define read_octeon_64bit_hash_sha512(index)		\
+({							\
+	u64 __value;					\
+							\
+	__asm__ __volatile__ (				\
+	"dmfc2 %[rt],0x0250+" STR(index)		\
+	: [rt] "=d" (__value)				\
+	: );						\
+							\
+	__value;					\
+})
+
+/*
+ * The index can be 0-14.
+ */
+#define write_octeon_64bit_block_sha512(value, index)	\
+do {							\
+	__asm__ __volatile__ (				\
+	"dmtc2 %[rt],0x0240+" STR(index)		\
+	:						\
+	: [rt] "d" (value));				\
+} while (0)
+
+/*
+ * The value is the final block word (64-bit).
+ */
+#define octeon_sha512_start(value)			\
+do {							\
+	__asm__ __volatile__ (				\
+	"dmtc2 %[rt],0x424f"				\
+	:						\
+	: [rt] "d" (value));				\
+} while (0)
+
+/*
+ * The value is the final block dword (64-bit).
+ */
+#define octeon_sha1_start(value)			\
+do {							\
+	__asm__ __volatile__ (				\
+	"dmtc2 %[rt],0x4057"				\
+	:						\
+	: [rt] "d" (value));				\
+} while (0)
+
+/*
+ * The value is the final block dword (64-bit).
+ */
+#define octeon_sha256_start(value)			\
+do {							\
+	__asm__ __volatile__ (				\
+	"dmtc2 %[rt],0x404f"				\
+	:						\
+	: [rt] "d" (value));				\
+} while (0)
+
+/*
+ * Macros needed to implement SHA512:
+ */
+
+/*
+ * The index can be 0-7.
+ */
+#define write_octeon_64bit_hash_sha512(value, index)	\
+do {							\
+	__asm__ __volatile__ (				\
+	"dmtc2 %[rt],0x0250+" STR(index)		\
+	:						\
+	: [rt] "d" (value));				\
+} while (0)
+
+/*
+ * The index can be 0-7.
+ */
+#define read_octeon_64bit_hash_sha512(index)		\
+({							\
+	u64 __value;					\
+							\
+	__asm__ __volatile__ (				\
+	"dmfc2 %[rt],0x0250+" STR(index)		\
+	: [rt] "=d" (__value)				\
+	: );						\
+							\
+	__value;					\
+})
+
+/*
+ * The index can be 0-14.
+ */
+#define write_octeon_64bit_block_sha512(value, index)	\
+do {							\
+	__asm__ __volatile__ (				\
+	"dmtc2 %[rt],0x0240+" STR(index)		\
+	:						\
+	: [rt] "d" (value));				\
+} while (0)
+
+/*
+ * The value is the final block word (64-bit).
+ */
+#define octeon_sha512_start(value)			\
+do {							\
+	__asm__ __volatile__ (				\
+	"dmtc2 %[rt],0x424f"				\
+	:						\
+	: [rt] "d" (value));				\
+} while (0)
+
+#endif /* __LINUX_OCTEON_CRYPTO_H */
diff --git a/arch/mips/cavium-octeon/crypto/octeon-md5.c b/arch/mips/cavium-octeon/crypto/octeon-md5.c
new file mode 100644
index 000000000..5ee4ade99
--- /dev/null
+++ b/arch/mips/cavium-octeon/crypto/octeon-md5.c
@@ -0,0 +1,208 @@
+/*
+ * Cryptographic API.
+ *
+ * MD5 Message Digest Algorithm (RFC1321).
+ *
+ * Adapted for OCTEON by Aaro Koskinen <aaro.koskinen@iki.fi>.
+ *
+ * Based on crypto/md5.c, which is:
+ *
+ * Derived from cryptoapi implementation, originally based on the
+ * public domain implementation written by Colin Plumb in 1993.
+ *
+ * Copyright (c) Cryptoapi developers.
+ * Copyright (c) 2002 James Morris <jmorris@intercode.com.au>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ */
+
+#include <crypto/md5.h>
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/module.h>
+#include <linux/string.h>
+#include <asm/byteorder.h>
+#include <asm/octeon/octeon.h>
+#include <crypto/internal/hash.h>
+
+#include "octeon-crypto.h"
+
+/*
+ * We pass everything as 64-bit. OCTEON can handle misaligned data.
+ */
+
+static void octeon_md5_store_hash(struct md5_state *ctx)
+{
+	u64 *hash = (u64 *)ctx->hash;
+
+	write_octeon_64bit_hash_dword(hash[0], 0);
+	write_octeon_64bit_hash_dword(hash[1], 1);
+}
+
+static void octeon_md5_read_hash(struct md5_state *ctx)
+{
+	u64 *hash = (u64 *)ctx->hash;
+
+	hash[0] = read_octeon_64bit_hash_dword(0);
+	hash[1] = read_octeon_64bit_hash_dword(1);
+}
+
+static void octeon_md5_transform(const void *_block)
+{
+	const u64 *block = _block;
+
+	write_octeon_64bit_block_dword(block[0], 0);
+	write_octeon_64bit_block_dword(block[1], 1);
+	write_octeon_64bit_block_dword(block[2], 2);
+	write_octeon_64bit_block_dword(block[3], 3);
+	write_octeon_64bit_block_dword(block[4], 4);
+	write_octeon_64bit_block_dword(block[5], 5);
+	write_octeon_64bit_block_dword(block[6], 6);
+	octeon_md5_start(block[7]);
+}
+
+static int octeon_md5_init(struct shash_desc *desc)
+{
+	struct md5_state *mctx = shash_desc_ctx(desc);
+
+	mctx->hash[0] = MD5_H0;
+	mctx->hash[1] = MD5_H1;
+	mctx->hash[2] = MD5_H2;
+	mctx->hash[3] = MD5_H3;
+	cpu_to_le32_array(mctx->hash, 4);
+	mctx->byte_count = 0;
+
+	return 0;
+}
+
+static int octeon_md5_update(struct shash_desc *desc, const u8 *data,
+			     unsigned int len)
+{
+	struct md5_state *mctx = shash_desc_ctx(desc);
+	const u32 avail = sizeof(mctx->block) - (mctx->byte_count & 0x3f);
+	struct octeon_cop2_state state;
+	unsigned long flags;
+
+	mctx->byte_count += len;
+
+	if (avail > len) {
+		memcpy((char *)mctx->block + (sizeof(mctx->block) - avail),
+		       data, len);
+		return 0;
+	}
+
+	memcpy((char *)mctx->block + (sizeof(mctx->block) - avail), data,
+	       avail);
+
+	flags = octeon_crypto_enable(&state);
+	octeon_md5_store_hash(mctx);
+
+	octeon_md5_transform(mctx->block);
+	data += avail;
+	len -= avail;
+
+	while (len >= sizeof(mctx->block)) {
+		octeon_md5_transform(data);
+		data += sizeof(mctx->block);
+		len -= sizeof(mctx->block);
+	}
+
+	octeon_md5_read_hash(mctx);
+	octeon_crypto_disable(&state, flags);
+
+	memcpy(mctx->block, data, len);
+
+	return 0;
+}
+
+static int octeon_md5_final(struct shash_desc *desc, u8 *out)
+{
+	struct md5_state *mctx = shash_desc_ctx(desc);
+	const unsigned int offset = mctx->byte_count & 0x3f;
+	char *p = (char *)mctx->block + offset;
+	int padding = 56 - (offset + 1);
+	struct octeon_cop2_state state;
+	unsigned long flags;
+
+	*p++ = 0x80;
+
+	flags = octeon_crypto_enable(&state);
+	octeon_md5_store_hash(mctx);
+
+	if (padding < 0) {
+		memset(p, 0x00, padding + sizeof(u64));
+		octeon_md5_transform(mctx->block);
+		p = (char *)mctx->block;
+		padding = 56;
+	}
+
+	memset(p, 0, padding);
+	mctx->block[14] = mctx->byte_count << 3;
+	mctx->block[15] = mctx->byte_count >> 29;
+	cpu_to_le32_array(mctx->block + 14, 2);
+	octeon_md5_transform(mctx->block);
+
+	octeon_md5_read_hash(mctx);
+	octeon_crypto_disable(&state, flags);
+
+	memcpy(out, mctx->hash, sizeof(mctx->hash));
+	memset(mctx, 0, sizeof(*mctx));
+
+	return 0;
+}
+
+static int octeon_md5_export(struct shash_desc *desc, void *out)
+{
+	struct md5_state *ctx = shash_desc_ctx(desc);
+
+	memcpy(out, ctx, sizeof(*ctx));
+	return 0;
+}
+
+static int octeon_md5_import(struct shash_desc *desc, const void *in)
+{
+	struct md5_state *ctx = shash_desc_ctx(desc);
+
+	memcpy(ctx, in, sizeof(*ctx));
+	return 0;
+}
+
+static struct shash_alg alg = {
+	.digestsize	=	MD5_DIGEST_SIZE,
+	.init		=	octeon_md5_init,
+	.update		=	octeon_md5_update,
+	.final		=	octeon_md5_final,
+	.export		=	octeon_md5_export,
+	.import		=	octeon_md5_import,
+	.descsize	=	sizeof(struct md5_state),
+	.statesize	=	sizeof(struct md5_state),
+	.base		=	{
+		.cra_name	=	"md5",
+		.cra_driver_name=	"octeon-md5",
+		.cra_priority	=	OCTEON_CR_OPCODE_PRIORITY,
+		.cra_blocksize	=	MD5_HMAC_BLOCK_SIZE,
+		.cra_module	=	THIS_MODULE,
+	}
+};
+
+static int __init md5_mod_init(void)
+{
+	if (!octeon_has_crypto())
+		return -ENOTSUPP;
+	return crypto_register_shash(&alg);
+}
+
+static void __exit md5_mod_fini(void)
+{
+	crypto_unregister_shash(&alg);
+}
+
+module_init(md5_mod_init);
+module_exit(md5_mod_fini);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("MD5 Message Digest Algorithm (OCTEON)");
+MODULE_AUTHOR("Aaro Koskinen <aaro.koskinen@iki.fi>");
diff --git a/arch/mips/cavium-octeon/crypto/octeon-sha1.c b/arch/mips/cavium-octeon/crypto/octeon-sha1.c
new file mode 100644
index 000000000..37a07b3c4
--- /dev/null
+++ b/arch/mips/cavium-octeon/crypto/octeon-sha1.c
@@ -0,0 +1,223 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Cryptographic API.
+ *
+ * SHA1 Secure Hash Algorithm.
+ *
+ * Adapted for OCTEON by Aaro Koskinen <aaro.koskinen@iki.fi>.
+ *
+ * Based on crypto/sha1_generic.c, which is:
+ *
+ * Copyright (c) Alan Smithee.
+ * Copyright (c) Andrew McDonald <andrew@mcdonald.org.uk>
+ * Copyright (c) Jean-Francois Dive <jef@linuxbe.org>
+ */
+
+#include <linux/mm.h>
+#include <crypto/sha1.h>
+#include <crypto/sha1_base.h>
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/module.h>
+#include <asm/byteorder.h>
+#include <asm/octeon/octeon.h>
+#include <crypto/internal/hash.h>
+
+#include "octeon-crypto.h"
+
+/*
+ * We pass everything as 64-bit. OCTEON can handle misaligned data.
+ */
+
+static void octeon_sha1_store_hash(struct sha1_state *sctx)
+{
+	u64 *hash = (u64 *)sctx->state;
+	union {
+		u32 word[2];
+		u64 dword;
+	} hash_tail = { { sctx->state[4], } };
+
+	write_octeon_64bit_hash_dword(hash[0], 0);
+	write_octeon_64bit_hash_dword(hash[1], 1);
+	write_octeon_64bit_hash_dword(hash_tail.dword, 2);
+	memzero_explicit(&hash_tail.word[0], sizeof(hash_tail.word[0]));
+}
+
+static void octeon_sha1_read_hash(struct sha1_state *sctx)
+{
+	u64 *hash = (u64 *)sctx->state;
+	union {
+		u32 word[2];
+		u64 dword;
+	} hash_tail;
+
+	hash[0]		= read_octeon_64bit_hash_dword(0);
+	hash[1]		= read_octeon_64bit_hash_dword(1);
+	hash_tail.dword	= read_octeon_64bit_hash_dword(2);
+	sctx->state[4]	= hash_tail.word[0];
+	memzero_explicit(&hash_tail.dword, sizeof(hash_tail.dword));
+}
+
+static void octeon_sha1_transform(const void *_block)
+{
+	const u64 *block = _block;
+
+	write_octeon_64bit_block_dword(block[0], 0);
+	write_octeon_64bit_block_dword(block[1], 1);
+	write_octeon_64bit_block_dword(block[2], 2);
+	write_octeon_64bit_block_dword(block[3], 3);
+	write_octeon_64bit_block_dword(block[4], 4);
+	write_octeon_64bit_block_dword(block[5], 5);
+	write_octeon_64bit_block_dword(block[6], 6);
+	octeon_sha1_start(block[7]);
+}
+
+static void __octeon_sha1_update(struct sha1_state *sctx, const u8 *data,
+				 unsigned int len)
+{
+	unsigned int partial;
+	unsigned int done;
+	const u8 *src;
+
+	partial = sctx->count % SHA1_BLOCK_SIZE;
+	sctx->count += len;
+	done = 0;
+	src = data;
+
+	if ((partial + len) >= SHA1_BLOCK_SIZE) {
+		if (partial) {
+			done = -partial;
+			memcpy(sctx->buffer + partial, data,
+			       done + SHA1_BLOCK_SIZE);
+			src = sctx->buffer;
+		}
+
+		do {
+			octeon_sha1_transform(src);
+			done += SHA1_BLOCK_SIZE;
+			src = data + done;
+		} while (done + SHA1_BLOCK_SIZE <= len);
+
+		partial = 0;
+	}
+	memcpy(sctx->buffer + partial, src, len - done);
+}
+
+static int octeon_sha1_update(struct shash_desc *desc, const u8 *data,
+			unsigned int len)
+{
+	struct sha1_state *sctx = shash_desc_ctx(desc);
+	struct octeon_cop2_state state;
+	unsigned long flags;
+
+	/*
+	 * Small updates never reach the crypto engine, so the generic sha1 is
+	 * faster because of the heavyweight octeon_crypto_enable() /
+	 * octeon_crypto_disable().
+	 */
+	if ((sctx->count % SHA1_BLOCK_SIZE) + len < SHA1_BLOCK_SIZE)
+		return crypto_sha1_update(desc, data, len);
+
+	flags = octeon_crypto_enable(&state);
+	octeon_sha1_store_hash(sctx);
+
+	__octeon_sha1_update(sctx, data, len);
+
+	octeon_sha1_read_hash(sctx);
+	octeon_crypto_disable(&state, flags);
+
+	return 0;
+}
+
+static int octeon_sha1_final(struct shash_desc *desc, u8 *out)
+{
+	struct sha1_state *sctx = shash_desc_ctx(desc);
+	static const u8 padding[64] = { 0x80, };
+	struct octeon_cop2_state state;
+	__be32 *dst = (__be32 *)out;
+	unsigned int pad_len;
+	unsigned long flags;
+	unsigned int index;
+	__be64 bits;
+	int i;
+
+	/* Save number of bits. */
+	bits = cpu_to_be64(sctx->count << 3);
+
+	/* Pad out to 56 mod 64. */
+	index = sctx->count & 0x3f;
+	pad_len = (index < 56) ? (56 - index) : ((64+56) - index);
+
+	flags = octeon_crypto_enable(&state);
+	octeon_sha1_store_hash(sctx);
+
+	__octeon_sha1_update(sctx, padding, pad_len);
+
+	/* Append length (before padding). */
+	__octeon_sha1_update(sctx, (const u8 *)&bits, sizeof(bits));
+
+	octeon_sha1_read_hash(sctx);
+	octeon_crypto_disable(&state, flags);
+
+	/* Store state in digest */
+	for (i = 0; i < 5; i++)
+		dst[i] = cpu_to_be32(sctx->state[i]);
+
+	/* Zeroize sensitive information. */
+	memset(sctx, 0, sizeof(*sctx));
+
+	return 0;
+}
+
+static int octeon_sha1_export(struct shash_desc *desc, void *out)
+{
+	struct sha1_state *sctx = shash_desc_ctx(desc);
+
+	memcpy(out, sctx, sizeof(*sctx));
+	return 0;
+}
+
+static int octeon_sha1_import(struct shash_desc *desc, const void *in)
+{
+	struct sha1_state *sctx = shash_desc_ctx(desc);
+
+	memcpy(sctx, in, sizeof(*sctx));
+	return 0;
+}
+
+static struct shash_alg octeon_sha1_alg = {
+	.digestsize	=	SHA1_DIGEST_SIZE,
+	.init		=	sha1_base_init,
+	.update		=	octeon_sha1_update,
+	.final		=	octeon_sha1_final,
+	.export		=	octeon_sha1_export,
+	.import		=	octeon_sha1_import,
+	.descsize	=	sizeof(struct sha1_state),
+	.statesize	=	sizeof(struct sha1_state),
+	.base		=	{
+		.cra_name	=	"sha1",
+		.cra_driver_name=	"octeon-sha1",
+		.cra_priority	=	OCTEON_CR_OPCODE_PRIORITY,
+		.cra_blocksize	=	SHA1_BLOCK_SIZE,
+		.cra_module	=	THIS_MODULE,
+	}
+};
+
+static int __init octeon_sha1_mod_init(void)
+{
+	if (!octeon_has_crypto())
+		return -ENOTSUPP;
+	return crypto_register_shash(&octeon_sha1_alg);
+}
+
+static void __exit octeon_sha1_mod_fini(void)
+{
+	crypto_unregister_shash(&octeon_sha1_alg);
+}
+
+module_init(octeon_sha1_mod_init);
+module_exit(octeon_sha1_mod_fini);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("SHA1 Secure Hash Algorithm (OCTEON)");
+MODULE_AUTHOR("Aaro Koskinen <aaro.koskinen@iki.fi>");
diff --git a/arch/mips/cavium-octeon/crypto/octeon-sha256.c b/arch/mips/cavium-octeon/crypto/octeon-sha256.c
new file mode 100644
index 000000000..435e4a6e7
--- /dev/null
+++ b/arch/mips/cavium-octeon/crypto/octeon-sha256.c
@@ -0,0 +1,241 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Cryptographic API.
+ *
+ * SHA-224 and SHA-256 Secure Hash Algorithm.
+ *
+ * Adapted for OCTEON by Aaro Koskinen <aaro.koskinen@iki.fi>.
+ *
+ * Based on crypto/sha256_generic.c, which is:
+ *
+ * Copyright (c) Jean-Luc Cooke <jlcooke@certainkey.com>
+ * Copyright (c) Andrew McDonald <andrew@mcdonald.org.uk>
+ * Copyright (c) 2002 James Morris <jmorris@intercode.com.au>
+ * SHA224 Support Copyright 2007 Intel Corporation <jonathan.lynch@intel.com>
+ */
+
+#include <linux/mm.h>
+#include <crypto/sha2.h>
+#include <crypto/sha256_base.h>
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/module.h>
+#include <asm/byteorder.h>
+#include <asm/octeon/octeon.h>
+#include <crypto/internal/hash.h>
+
+#include "octeon-crypto.h"
+
+/*
+ * We pass everything as 64-bit. OCTEON can handle misaligned data.
+ */
+
+static void octeon_sha256_store_hash(struct sha256_state *sctx)
+{
+	u64 *hash = (u64 *)sctx->state;
+
+	write_octeon_64bit_hash_dword(hash[0], 0);
+	write_octeon_64bit_hash_dword(hash[1], 1);
+	write_octeon_64bit_hash_dword(hash[2], 2);
+	write_octeon_64bit_hash_dword(hash[3], 3);
+}
+
+static void octeon_sha256_read_hash(struct sha256_state *sctx)
+{
+	u64 *hash = (u64 *)sctx->state;
+
+	hash[0] = read_octeon_64bit_hash_dword(0);
+	hash[1] = read_octeon_64bit_hash_dword(1);
+	hash[2] = read_octeon_64bit_hash_dword(2);
+	hash[3] = read_octeon_64bit_hash_dword(3);
+}
+
+static void octeon_sha256_transform(const void *_block)
+{
+	const u64 *block = _block;
+
+	write_octeon_64bit_block_dword(block[0], 0);
+	write_octeon_64bit_block_dword(block[1], 1);
+	write_octeon_64bit_block_dword(block[2], 2);
+	write_octeon_64bit_block_dword(block[3], 3);
+	write_octeon_64bit_block_dword(block[4], 4);
+	write_octeon_64bit_block_dword(block[5], 5);
+	write_octeon_64bit_block_dword(block[6], 6);
+	octeon_sha256_start(block[7]);
+}
+
+static void __octeon_sha256_update(struct sha256_state *sctx, const u8 *data,
+				   unsigned int len)
+{
+	unsigned int partial;
+	unsigned int done;
+	const u8 *src;
+
+	partial = sctx->count % SHA256_BLOCK_SIZE;
+	sctx->count += len;
+	done = 0;
+	src = data;
+
+	if ((partial + len) >= SHA256_BLOCK_SIZE) {
+		if (partial) {
+			done = -partial;
+			memcpy(sctx->buf + partial, data,
+			       done + SHA256_BLOCK_SIZE);
+			src = sctx->buf;
+		}
+
+		do {
+			octeon_sha256_transform(src);
+			done += SHA256_BLOCK_SIZE;
+			src = data + done;
+		} while (done + SHA256_BLOCK_SIZE <= len);
+
+		partial = 0;
+	}
+	memcpy(sctx->buf + partial, src, len - done);
+}
+
+static int octeon_sha256_update(struct shash_desc *desc, const u8 *data,
+				unsigned int len)
+{
+	struct sha256_state *sctx = shash_desc_ctx(desc);
+	struct octeon_cop2_state state;
+	unsigned long flags;
+
+	/*
+	 * Small updates never reach the crypto engine, so the generic sha256 is
+	 * faster because of the heavyweight octeon_crypto_enable() /
+	 * octeon_crypto_disable().
+	 */
+	if ((sctx->count % SHA256_BLOCK_SIZE) + len < SHA256_BLOCK_SIZE)
+		return crypto_sha256_update(desc, data, len);
+
+	flags = octeon_crypto_enable(&state);
+	octeon_sha256_store_hash(sctx);
+
+	__octeon_sha256_update(sctx, data, len);
+
+	octeon_sha256_read_hash(sctx);
+	octeon_crypto_disable(&state, flags);
+
+	return 0;
+}
+
+static int octeon_sha256_final(struct shash_desc *desc, u8 *out)
+{
+	struct sha256_state *sctx = shash_desc_ctx(desc);
+	static const u8 padding[64] = { 0x80, };
+	struct octeon_cop2_state state;
+	__be32 *dst = (__be32 *)out;
+	unsigned int pad_len;
+	unsigned long flags;
+	unsigned int index;
+	__be64 bits;
+	int i;
+
+	/* Save number of bits. */
+	bits = cpu_to_be64(sctx->count << 3);
+
+	/* Pad out to 56 mod 64. */
+	index = sctx->count & 0x3f;
+	pad_len = (index < 56) ? (56 - index) : ((64+56) - index);
+
+	flags = octeon_crypto_enable(&state);
+	octeon_sha256_store_hash(sctx);
+
+	__octeon_sha256_update(sctx, padding, pad_len);
+
+	/* Append length (before padding). */
+	__octeon_sha256_update(sctx, (const u8 *)&bits, sizeof(bits));
+
+	octeon_sha256_read_hash(sctx);
+	octeon_crypto_disable(&state, flags);
+
+	/* Store state in digest */
+	for (i = 0; i < 8; i++)
+		dst[i] = cpu_to_be32(sctx->state[i]);
+
+	/* Zeroize sensitive information. */
+	memset(sctx, 0, sizeof(*sctx));
+
+	return 0;
+}
+
+static int octeon_sha224_final(struct shash_desc *desc, u8 *hash)
+{
+	u8 D[SHA256_DIGEST_SIZE];
+
+	octeon_sha256_final(desc, D);
+
+	memcpy(hash, D, SHA224_DIGEST_SIZE);
+	memzero_explicit(D, SHA256_DIGEST_SIZE);
+
+	return 0;
+}
+
+static int octeon_sha256_export(struct shash_desc *desc, void *out)
+{
+	struct sha256_state *sctx = shash_desc_ctx(desc);
+
+	memcpy(out, sctx, sizeof(*sctx));
+	return 0;
+}
+
+static int octeon_sha256_import(struct shash_desc *desc, const void *in)
+{
+	struct sha256_state *sctx = shash_desc_ctx(desc);
+
+	memcpy(sctx, in, sizeof(*sctx));
+	return 0;
+}
+
+static struct shash_alg octeon_sha256_algs[2] = { {
+	.digestsize	=	SHA256_DIGEST_SIZE,
+	.init		=	sha256_base_init,
+	.update		=	octeon_sha256_update,
+	.final		=	octeon_sha256_final,
+	.export		=	octeon_sha256_export,
+	.import		=	octeon_sha256_import,
+	.descsize	=	sizeof(struct sha256_state),
+	.statesize	=	sizeof(struct sha256_state),
+	.base		=	{
+		.cra_name	=	"sha256",
+		.cra_driver_name=	"octeon-sha256",
+		.cra_priority	=	OCTEON_CR_OPCODE_PRIORITY,
+		.cra_blocksize	=	SHA256_BLOCK_SIZE,
+		.cra_module	=	THIS_MODULE,
+	}
+}, {
+	.digestsize	=	SHA224_DIGEST_SIZE,
+	.init		=	sha224_base_init,
+	.update		=	octeon_sha256_update,
+	.final		=	octeon_sha224_final,
+	.descsize	=	sizeof(struct sha256_state),
+	.base		=	{
+		.cra_name	=	"sha224",
+		.cra_driver_name=	"octeon-sha224",
+		.cra_blocksize	=	SHA224_BLOCK_SIZE,
+		.cra_module	=	THIS_MODULE,
+	}
+} };
+
+static int __init octeon_sha256_mod_init(void)
+{
+	if (!octeon_has_crypto())
+		return -ENOTSUPP;
+	return crypto_register_shashes(octeon_sha256_algs,
+				       ARRAY_SIZE(octeon_sha256_algs));
+}
+
+static void __exit octeon_sha256_mod_fini(void)
+{
+	crypto_unregister_shashes(octeon_sha256_algs,
+				  ARRAY_SIZE(octeon_sha256_algs));
+}
+
+module_init(octeon_sha256_mod_init);
+module_exit(octeon_sha256_mod_fini);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("SHA-224 and SHA-256 Secure Hash Algorithm (OCTEON)");
+MODULE_AUTHOR("Aaro Koskinen <aaro.koskinen@iki.fi>");
diff --git a/arch/mips/cavium-octeon/crypto/octeon-sha512.c b/arch/mips/cavium-octeon/crypto/octeon-sha512.c
new file mode 100644
index 000000000..2dee9354e
--- /dev/null
+++ b/arch/mips/cavium-octeon/crypto/octeon-sha512.c
@@ -0,0 +1,238 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Cryptographic API.
+ *
+ * SHA-512 and SHA-384 Secure Hash Algorithm.
+ *
+ * Adapted for OCTEON by Aaro Koskinen <aaro.koskinen@iki.fi>.
+ *
+ * Based on crypto/sha512_generic.c, which is:
+ *
+ * Copyright (c) Jean-Luc Cooke <jlcooke@certainkey.com>
+ * Copyright (c) Andrew McDonald <andrew@mcdonald.org.uk>
+ * Copyright (c) 2003 Kyle McMartin <kyle@debian.org>
+ */
+
+#include <linux/mm.h>
+#include <crypto/sha2.h>
+#include <crypto/sha512_base.h>
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/module.h>
+#include <asm/byteorder.h>
+#include <asm/octeon/octeon.h>
+#include <crypto/internal/hash.h>
+
+#include "octeon-crypto.h"
+
+/*
+ * We pass everything as 64-bit. OCTEON can handle misaligned data.
+ */
+
+static void octeon_sha512_store_hash(struct sha512_state *sctx)
+{
+	write_octeon_64bit_hash_sha512(sctx->state[0], 0);
+	write_octeon_64bit_hash_sha512(sctx->state[1], 1);
+	write_octeon_64bit_hash_sha512(sctx->state[2], 2);
+	write_octeon_64bit_hash_sha512(sctx->state[3], 3);
+	write_octeon_64bit_hash_sha512(sctx->state[4], 4);
+	write_octeon_64bit_hash_sha512(sctx->state[5], 5);
+	write_octeon_64bit_hash_sha512(sctx->state[6], 6);
+	write_octeon_64bit_hash_sha512(sctx->state[7], 7);
+}
+
+static void octeon_sha512_read_hash(struct sha512_state *sctx)
+{
+	sctx->state[0] = read_octeon_64bit_hash_sha512(0);
+	sctx->state[1] = read_octeon_64bit_hash_sha512(1);
+	sctx->state[2] = read_octeon_64bit_hash_sha512(2);
+	sctx->state[3] = read_octeon_64bit_hash_sha512(3);
+	sctx->state[4] = read_octeon_64bit_hash_sha512(4);
+	sctx->state[5] = read_octeon_64bit_hash_sha512(5);
+	sctx->state[6] = read_octeon_64bit_hash_sha512(6);
+	sctx->state[7] = read_octeon_64bit_hash_sha512(7);
+}
+
+static void octeon_sha512_transform(const void *_block)
+{
+	const u64 *block = _block;
+
+	write_octeon_64bit_block_sha512(block[0], 0);
+	write_octeon_64bit_block_sha512(block[1], 1);
+	write_octeon_64bit_block_sha512(block[2], 2);
+	write_octeon_64bit_block_sha512(block[3], 3);
+	write_octeon_64bit_block_sha512(block[4], 4);
+	write_octeon_64bit_block_sha512(block[5], 5);
+	write_octeon_64bit_block_sha512(block[6], 6);
+	write_octeon_64bit_block_sha512(block[7], 7);
+	write_octeon_64bit_block_sha512(block[8], 8);
+	write_octeon_64bit_block_sha512(block[9], 9);
+	write_octeon_64bit_block_sha512(block[10], 10);
+	write_octeon_64bit_block_sha512(block[11], 11);
+	write_octeon_64bit_block_sha512(block[12], 12);
+	write_octeon_64bit_block_sha512(block[13], 13);
+	write_octeon_64bit_block_sha512(block[14], 14);
+	octeon_sha512_start(block[15]);
+}
+
+static void __octeon_sha512_update(struct sha512_state *sctx, const u8 *data,
+				   unsigned int len)
+{
+	unsigned int part_len;
+	unsigned int index;
+	unsigned int i;
+
+	/* Compute number of bytes mod 128. */
+	index = sctx->count[0] % SHA512_BLOCK_SIZE;
+
+	/* Update number of bytes. */
+	if ((sctx->count[0] += len) < len)
+		sctx->count[1]++;
+
+	part_len = SHA512_BLOCK_SIZE - index;
+
+	/* Transform as many times as possible. */
+	if (len >= part_len) {
+		memcpy(&sctx->buf[index], data, part_len);
+		octeon_sha512_transform(sctx->buf);
+
+		for (i = part_len; i + SHA512_BLOCK_SIZE <= len;
+			i += SHA512_BLOCK_SIZE)
+			octeon_sha512_transform(&data[i]);
+
+		index = 0;
+	} else {
+		i = 0;
+	}
+
+	/* Buffer remaining input. */
+	memcpy(&sctx->buf[index], &data[i], len - i);
+}
+
+static int octeon_sha512_update(struct shash_desc *desc, const u8 *data,
+				unsigned int len)
+{
+	struct sha512_state *sctx = shash_desc_ctx(desc);
+	struct octeon_cop2_state state;
+	unsigned long flags;
+
+	/*
+	 * Small updates never reach the crypto engine, so the generic sha512 is
+	 * faster because of the heavyweight octeon_crypto_enable() /
+	 * octeon_crypto_disable().
+	 */
+	if ((sctx->count[0] % SHA512_BLOCK_SIZE) + len < SHA512_BLOCK_SIZE)
+		return crypto_sha512_update(desc, data, len);
+
+	flags = octeon_crypto_enable(&state);
+	octeon_sha512_store_hash(sctx);
+
+	__octeon_sha512_update(sctx, data, len);
+
+	octeon_sha512_read_hash(sctx);
+	octeon_crypto_disable(&state, flags);
+
+	return 0;
+}
+
+static int octeon_sha512_final(struct shash_desc *desc, u8 *hash)
+{
+	struct sha512_state *sctx = shash_desc_ctx(desc);
+	static u8 padding[128] = { 0x80, };
+	struct octeon_cop2_state state;
+	__be64 *dst = (__be64 *)hash;
+	unsigned int pad_len;
+	unsigned long flags;
+	unsigned int index;
+	__be64 bits[2];
+	int i;
+
+	/* Save number of bits. */
+	bits[1] = cpu_to_be64(sctx->count[0] << 3);
+	bits[0] = cpu_to_be64(sctx->count[1] << 3 | sctx->count[0] >> 61);
+
+	/* Pad out to 112 mod 128. */
+	index = sctx->count[0] & 0x7f;
+	pad_len = (index < 112) ? (112 - index) : ((128+112) - index);
+
+	flags = octeon_crypto_enable(&state);
+	octeon_sha512_store_hash(sctx);
+
+	__octeon_sha512_update(sctx, padding, pad_len);
+
+	/* Append length (before padding). */
+	__octeon_sha512_update(sctx, (const u8 *)bits, sizeof(bits));
+
+	octeon_sha512_read_hash(sctx);
+	octeon_crypto_disable(&state, flags);
+
+	/* Store state in digest. */
+	for (i = 0; i < 8; i++)
+		dst[i] = cpu_to_be64(sctx->state[i]);
+
+	/* Zeroize sensitive information. */
+	memset(sctx, 0, sizeof(struct sha512_state));
+
+	return 0;
+}
+
+static int octeon_sha384_final(struct shash_desc *desc, u8 *hash)
+{
+	u8 D[64];
+
+	octeon_sha512_final(desc, D);
+
+	memcpy(hash, D, 48);
+	memzero_explicit(D, 64);
+
+	return 0;
+}
+
+static struct shash_alg octeon_sha512_algs[2] = { {
+	.digestsize	=	SHA512_DIGEST_SIZE,
+	.init		=	sha512_base_init,
+	.update		=	octeon_sha512_update,
+	.final		=	octeon_sha512_final,
+	.descsize	=	sizeof(struct sha512_state),
+	.base		=	{
+		.cra_name	=	"sha512",
+		.cra_driver_name=	"octeon-sha512",
+		.cra_priority	=	OCTEON_CR_OPCODE_PRIORITY,
+		.cra_blocksize	=	SHA512_BLOCK_SIZE,
+		.cra_module	=	THIS_MODULE,
+	}
+}, {
+	.digestsize	=	SHA384_DIGEST_SIZE,
+	.init		=	sha384_base_init,
+	.update		=	octeon_sha512_update,
+	.final		=	octeon_sha384_final,
+	.descsize	=	sizeof(struct sha512_state),
+	.base		=	{
+		.cra_name	=	"sha384",
+		.cra_driver_name=	"octeon-sha384",
+		.cra_priority	=	OCTEON_CR_OPCODE_PRIORITY,
+		.cra_blocksize	=	SHA384_BLOCK_SIZE,
+		.cra_module	=	THIS_MODULE,
+	}
+} };
+
+static int __init octeon_sha512_mod_init(void)
+{
+	if (!octeon_has_crypto())
+		return -ENOTSUPP;
+	return crypto_register_shashes(octeon_sha512_algs,
+				       ARRAY_SIZE(octeon_sha512_algs));
+}
+
+static void __exit octeon_sha512_mod_fini(void)
+{
+	crypto_unregister_shashes(octeon_sha512_algs,
+				  ARRAY_SIZE(octeon_sha512_algs));
+}
+
+module_init(octeon_sha512_mod_init);
+module_exit(octeon_sha512_mod_fini);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("SHA-512 and SHA-384 Secure Hash Algorithms (OCTEON)");
+MODULE_AUTHOR("Aaro Koskinen <aaro.koskinen@iki.fi>");
diff --git a/arch/mips/cavium-octeon/csrc-octeon.c b/arch/mips/cavium-octeon/csrc-octeon.c
new file mode 100644
index 000000000..124817609
--- /dev/null
+++ b/arch/mips/cavium-octeon/csrc-octeon.c
@@ -0,0 +1,214 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2007 by Ralf Baechle
+ * Copyright (C) 2009, 2012 Cavium, Inc.
+ */
+#include <linux/clocksource.h>
+#include <linux/sched/clock.h>
+#include <linux/export.h>
+#include <linux/init.h>
+#include <linux/smp.h>
+
+#include <asm/cpu-info.h>
+#include <asm/cpu-type.h>
+#include <asm/time.h>
+
+#include <asm/octeon/octeon.h>
+#include <asm/octeon/cvmx-ipd-defs.h>
+#include <asm/octeon/cvmx-mio-defs.h>
+#include <asm/octeon/cvmx-rst-defs.h>
+#include <asm/octeon/cvmx-fpa-defs.h>
+
+static u64 f;
+static u64 rdiv;
+static u64 sdiv;
+static u64 octeon_udelay_factor;
+static u64 octeon_ndelay_factor;
+
+void __init octeon_setup_delays(void)
+{
+	octeon_udelay_factor = octeon_get_clock_rate() / 1000000;
+	/*
+	 * For __ndelay we divide by 2^16, so the factor is multiplied
+	 * by the same amount.
+	 */
+	octeon_ndelay_factor = (octeon_udelay_factor * 0x10000ull) / 1000ull;
+
+	preset_lpj = octeon_get_clock_rate() / HZ;
+
+	if (current_cpu_type() == CPU_CAVIUM_OCTEON2) {
+		union cvmx_mio_rst_boot rst_boot;
+
+		rst_boot.u64 = cvmx_read_csr(CVMX_MIO_RST_BOOT);
+		rdiv = rst_boot.s.c_mul;	/* CPU clock */
+		sdiv = rst_boot.s.pnr_mul;	/* I/O clock */
+		f = (0x8000000000000000ull / sdiv) * 2;
+	} else if (current_cpu_type() == CPU_CAVIUM_OCTEON3) {
+		union cvmx_rst_boot rst_boot;
+
+		rst_boot.u64 = cvmx_read_csr(CVMX_RST_BOOT);
+		rdiv = rst_boot.s.c_mul;	/* CPU clock */
+		sdiv = rst_boot.s.pnr_mul;	/* I/O clock */
+		f = (0x8000000000000000ull / sdiv) * 2;
+	}
+
+}
+
+/*
+ * Set the current core's cvmcount counter to the value of the
+ * IPD_CLK_COUNT.  We do this on all cores as they are brought
+ * on-line.  This allows for a read from a local cpu register to
+ * access a synchronized counter.
+ *
+ * On CPU_CAVIUM_OCTEON2 the IPD_CLK_COUNT is scaled by rdiv/sdiv.
+ */
+void octeon_init_cvmcount(void)
+{
+	u64 clk_reg;
+	unsigned long flags;
+	unsigned loops = 2;
+
+	clk_reg = octeon_has_feature(OCTEON_FEATURE_FPA3) ?
+		CVMX_FPA_CLK_COUNT : CVMX_IPD_CLK_COUNT;
+
+	/* Clobber loops so GCC will not unroll the following while loop. */
+	asm("" : "+r" (loops));
+
+	local_irq_save(flags);
+	/*
+	 * Loop several times so we are executing from the cache,
+	 * which should give more deterministic timing.
+	 */
+	while (loops--) {
+		u64 clk_count = cvmx_read_csr(clk_reg);
+		if (rdiv != 0) {
+			clk_count *= rdiv;
+			if (f != 0) {
+				asm("dmultu\t%[cnt],%[f]\n\t"
+				    "mfhi\t%[cnt]"
+				    : [cnt] "+r" (clk_count)
+				    : [f] "r" (f)
+				    : "hi", "lo");
+			}
+		}
+		write_c0_cvmcount(clk_count);
+	}
+	local_irq_restore(flags);
+}
+
+static u64 octeon_cvmcount_read(struct clocksource *cs)
+{
+	return read_c0_cvmcount();
+}
+
+static struct clocksource clocksource_mips = {
+	.name		= "OCTEON_CVMCOUNT",
+	.read		= octeon_cvmcount_read,
+	.mask		= CLOCKSOURCE_MASK(64),
+	.flags		= CLOCK_SOURCE_IS_CONTINUOUS,
+};
+
+unsigned long long notrace sched_clock(void)
+{
+	/* 64-bit arithmatic can overflow, so use 128-bit.  */
+	u64 t1, t2, t3;
+	unsigned long long rv;
+	u64 mult = clocksource_mips.mult;
+	u64 shift = clocksource_mips.shift;
+	u64 cnt = read_c0_cvmcount();
+
+	asm (
+		"dmultu\t%[cnt],%[mult]\n\t"
+		"nor\t%[t1],$0,%[shift]\n\t"
+		"mfhi\t%[t2]\n\t"
+		"mflo\t%[t3]\n\t"
+		"dsll\t%[t2],%[t2],1\n\t"
+		"dsrlv\t%[rv],%[t3],%[shift]\n\t"
+		"dsllv\t%[t1],%[t2],%[t1]\n\t"
+		"or\t%[rv],%[t1],%[rv]\n\t"
+		: [rv] "=&r" (rv), [t1] "=&r" (t1), [t2] "=&r" (t2), [t3] "=&r" (t3)
+		: [cnt] "r" (cnt), [mult] "r" (mult), [shift] "r" (shift)
+		: "hi", "lo");
+	return rv;
+}
+
+void __init plat_time_init(void)
+{
+	clocksource_mips.rating = 300;
+	clocksource_register_hz(&clocksource_mips, octeon_get_clock_rate());
+}
+
+void __udelay(unsigned long us)
+{
+	u64 cur, end, inc;
+
+	cur = read_c0_cvmcount();
+
+	inc = us * octeon_udelay_factor;
+	end = cur + inc;
+
+	while (end > cur)
+		cur = read_c0_cvmcount();
+}
+EXPORT_SYMBOL(__udelay);
+
+void __ndelay(unsigned long ns)
+{
+	u64 cur, end, inc;
+
+	cur = read_c0_cvmcount();
+
+	inc = ((ns * octeon_ndelay_factor) >> 16);
+	end = cur + inc;
+
+	while (end > cur)
+		cur = read_c0_cvmcount();
+}
+EXPORT_SYMBOL(__ndelay);
+
+void __delay(unsigned long loops)
+{
+	u64 cur, end;
+
+	cur = read_c0_cvmcount();
+	end = cur + loops;
+
+	while (end > cur)
+		cur = read_c0_cvmcount();
+}
+EXPORT_SYMBOL(__delay);
+
+
+/**
+ * octeon_io_clk_delay - wait for a given number of io clock cycles to pass.
+ *
+ * We scale the wait by the clock ratio, and then wait for the
+ * corresponding number of core clocks.
+ *
+ * @count: The number of clocks to wait.
+ */
+void octeon_io_clk_delay(unsigned long count)
+{
+	u64 cur, end;
+
+	cur = read_c0_cvmcount();
+	if (rdiv != 0) {
+		end = count * rdiv;
+		if (f != 0) {
+			asm("dmultu\t%[cnt],%[f]\n\t"
+				"mfhi\t%[cnt]"
+				: [cnt] "+r" (end)
+				: [f] "r" (f)
+				: "hi", "lo");
+		}
+		end = cur + end;
+	} else {
+		end = cur + count;
+	}
+	while (end > cur)
+		cur = read_c0_cvmcount();
+}
+EXPORT_SYMBOL(octeon_io_clk_delay);
diff --git a/arch/mips/cavium-octeon/dma-octeon.c b/arch/mips/cavium-octeon/dma-octeon.c
new file mode 100644
index 000000000..9fbba6a8f
--- /dev/null
+++ b/arch/mips/cavium-octeon/dma-octeon.c
@@ -0,0 +1,239 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2000  Ani Joshi <ajoshi@unixbox.com>
+ * Copyright (C) 2000, 2001  Ralf Baechle <ralf@gnu.org>
+ * Copyright (C) 2005 Ilya A. Volynets-Evenbakh <ilya@total-knowledge.com>
+ * swiped from i386, and cloned for MIPS by Geert, polished by Ralf.
+ * IP32 changes by Ilya.
+ * Copyright (C) 2010 Cavium Networks, Inc.
+ */
+#include <linux/dma-direct.h>
+#include <linux/memblock.h>
+#include <linux/swiotlb.h>
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+
+#include <asm/bootinfo.h>
+
+#include <asm/octeon/octeon.h>
+
+#ifdef CONFIG_PCI
+#include <linux/pci.h>
+#include <asm/octeon/pci-octeon.h>
+#include <asm/octeon/cvmx-npi-defs.h>
+#include <asm/octeon/cvmx-pci-defs.h>
+
+struct octeon_dma_map_ops {
+	dma_addr_t (*phys_to_dma)(struct device *dev, phys_addr_t paddr);
+	phys_addr_t (*dma_to_phys)(struct device *dev, dma_addr_t daddr);
+};
+
+static dma_addr_t octeon_hole_phys_to_dma(phys_addr_t paddr)
+{
+	if (paddr >= CVMX_PCIE_BAR1_PHYS_BASE && paddr < (CVMX_PCIE_BAR1_PHYS_BASE + CVMX_PCIE_BAR1_PHYS_SIZE))
+		return paddr - CVMX_PCIE_BAR1_PHYS_BASE + CVMX_PCIE_BAR1_RC_BASE;
+	else
+		return paddr;
+}
+
+static phys_addr_t octeon_hole_dma_to_phys(dma_addr_t daddr)
+{
+	if (daddr >= CVMX_PCIE_BAR1_RC_BASE)
+		return daddr + CVMX_PCIE_BAR1_PHYS_BASE - CVMX_PCIE_BAR1_RC_BASE;
+	else
+		return daddr;
+}
+
+static dma_addr_t octeon_gen1_phys_to_dma(struct device *dev, phys_addr_t paddr)
+{
+	if (paddr >= 0x410000000ull && paddr < 0x420000000ull)
+		paddr -= 0x400000000ull;
+	return octeon_hole_phys_to_dma(paddr);
+}
+
+static phys_addr_t octeon_gen1_dma_to_phys(struct device *dev, dma_addr_t daddr)
+{
+	daddr = octeon_hole_dma_to_phys(daddr);
+
+	if (daddr >= 0x10000000ull && daddr < 0x20000000ull)
+		daddr += 0x400000000ull;
+
+	return daddr;
+}
+
+static const struct octeon_dma_map_ops octeon_gen1_ops = {
+	.phys_to_dma	= octeon_gen1_phys_to_dma,
+	.dma_to_phys	= octeon_gen1_dma_to_phys,
+};
+
+static dma_addr_t octeon_gen2_phys_to_dma(struct device *dev, phys_addr_t paddr)
+{
+	return octeon_hole_phys_to_dma(paddr);
+}
+
+static phys_addr_t octeon_gen2_dma_to_phys(struct device *dev, dma_addr_t daddr)
+{
+	return octeon_hole_dma_to_phys(daddr);
+}
+
+static const struct octeon_dma_map_ops octeon_gen2_ops = {
+	.phys_to_dma	= octeon_gen2_phys_to_dma,
+	.dma_to_phys	= octeon_gen2_dma_to_phys,
+};
+
+static dma_addr_t octeon_big_phys_to_dma(struct device *dev, phys_addr_t paddr)
+{
+	if (paddr >= 0x410000000ull && paddr < 0x420000000ull)
+		paddr -= 0x400000000ull;
+
+	/* Anything in the BAR1 hole or above goes via BAR2 */
+	if (paddr >= 0xf0000000ull)
+		paddr = OCTEON_BAR2_PCI_ADDRESS + paddr;
+
+	return paddr;
+}
+
+static phys_addr_t octeon_big_dma_to_phys(struct device *dev, dma_addr_t daddr)
+{
+	if (daddr >= OCTEON_BAR2_PCI_ADDRESS)
+		daddr -= OCTEON_BAR2_PCI_ADDRESS;
+
+	if (daddr >= 0x10000000ull && daddr < 0x20000000ull)
+		daddr += 0x400000000ull;
+	return daddr;
+}
+
+static const struct octeon_dma_map_ops octeon_big_ops = {
+	.phys_to_dma	= octeon_big_phys_to_dma,
+	.dma_to_phys	= octeon_big_dma_to_phys,
+};
+
+static dma_addr_t octeon_small_phys_to_dma(struct device *dev,
+					   phys_addr_t paddr)
+{
+	if (paddr >= 0x410000000ull && paddr < 0x420000000ull)
+		paddr -= 0x400000000ull;
+
+	/* Anything not in the BAR1 range goes via BAR2 */
+	if (paddr >= octeon_bar1_pci_phys && paddr < octeon_bar1_pci_phys + 0x8000000ull)
+		paddr = paddr - octeon_bar1_pci_phys;
+	else
+		paddr = OCTEON_BAR2_PCI_ADDRESS + paddr;
+
+	return paddr;
+}
+
+static phys_addr_t octeon_small_dma_to_phys(struct device *dev,
+					    dma_addr_t daddr)
+{
+	if (daddr >= OCTEON_BAR2_PCI_ADDRESS)
+		daddr -= OCTEON_BAR2_PCI_ADDRESS;
+	else
+		daddr += octeon_bar1_pci_phys;
+
+	if (daddr >= 0x10000000ull && daddr < 0x20000000ull)
+		daddr += 0x400000000ull;
+	return daddr;
+}
+
+static const struct octeon_dma_map_ops octeon_small_ops = {
+	.phys_to_dma	= octeon_small_phys_to_dma,
+	.dma_to_phys	= octeon_small_dma_to_phys,
+};
+
+static const struct octeon_dma_map_ops *octeon_pci_dma_ops;
+
+void __init octeon_pci_dma_init(void)
+{
+	switch (octeon_dma_bar_type) {
+	case OCTEON_DMA_BAR_TYPE_PCIE:
+		octeon_pci_dma_ops = &octeon_gen1_ops;
+		break;
+	case OCTEON_DMA_BAR_TYPE_PCIE2:
+		octeon_pci_dma_ops = &octeon_gen2_ops;
+		break;
+	case OCTEON_DMA_BAR_TYPE_BIG:
+		octeon_pci_dma_ops = &octeon_big_ops;
+		break;
+	case OCTEON_DMA_BAR_TYPE_SMALL:
+		octeon_pci_dma_ops = &octeon_small_ops;
+		break;
+	default:
+		BUG();
+	}
+}
+#endif /* CONFIG_PCI */
+
+dma_addr_t phys_to_dma(struct device *dev, phys_addr_t paddr)
+{
+#ifdef CONFIG_PCI
+	if (dev && dev_is_pci(dev))
+		return octeon_pci_dma_ops->phys_to_dma(dev, paddr);
+#endif
+	return paddr;
+}
+
+phys_addr_t dma_to_phys(struct device *dev, dma_addr_t daddr)
+{
+#ifdef CONFIG_PCI
+	if (dev && dev_is_pci(dev))
+		return octeon_pci_dma_ops->dma_to_phys(dev, daddr);
+#endif
+	return daddr;
+}
+
+void __init plat_swiotlb_setup(void)
+{
+	phys_addr_t start, end;
+	phys_addr_t max_addr;
+	phys_addr_t addr_size;
+	size_t swiotlbsize;
+	u64 i;
+
+	max_addr = 0;
+	addr_size = 0;
+
+	for_each_mem_range(i, &start, &end) {
+		/* These addresses map low for PCI. */
+		if (start > 0x410000000ull && !OCTEON_IS_OCTEON2())
+			continue;
+
+		addr_size += (end - start);
+
+		if (max_addr < end)
+			max_addr = end;
+	}
+
+	swiotlbsize = PAGE_SIZE;
+
+#ifdef CONFIG_PCI
+	/*
+	 * For OCTEON_DMA_BAR_TYPE_SMALL, size the iotlb at 1/4 memory
+	 * size to a maximum of 64MB
+	 */
+	if (OCTEON_IS_MODEL(OCTEON_CN31XX)
+	    || OCTEON_IS_MODEL(OCTEON_CN38XX_PASS2)) {
+		swiotlbsize = addr_size / 4;
+		if (swiotlbsize > 64 * (1<<20))
+			swiotlbsize = 64 * (1<<20);
+	} else if (max_addr > 0xf0000000ul) {
+		/*
+		 * Otherwise only allocate a big iotlb if there is
+		 * memory past the BAR1 hole.
+		 */
+		swiotlbsize = 64 * (1<<20);
+	}
+#endif
+#ifdef CONFIG_USB_OHCI_HCD_PLATFORM
+	/* OCTEON II ohci is only 32-bit. */
+	if (OCTEON_IS_OCTEON2() && max_addr >= 0x100000000ul)
+		swiotlbsize = 64 * (1<<20);
+#endif
+
+	swiotlb_adjust_size(swiotlbsize);
+	swiotlb_init(true, SWIOTLB_VERBOSE);
+}
diff --git a/arch/mips/cavium-octeon/executive/Makefile b/arch/mips/cavium-octeon/executive/Makefile
new file mode 100644
index 000000000..50b427879
--- /dev/null
+++ b/arch/mips/cavium-octeon/executive/Makefile
@@ -0,0 +1,19 @@
+#
+# Makefile for the Cavium Octeon specific kernel interface routines
+# under Linux.
+#
+# This file is subject to the terms and conditions of the GNU General Public
+# License.  See the file "COPYING" in the main directory of this archive
+# for more details.
+#
+# Copyright (C) 2005-2008 Cavium Networks
+#
+
+obj-y += cvmx-bootmem.o cvmx-l2c.o cvmx-sysinfo.o octeon-model.o
+obj-y += cvmx-pko.o cvmx-spi.o cvmx-cmd-queue.o \
+	cvmx-helper-board.o cvmx-helper.o cvmx-helper-xaui.o \
+	cvmx-helper-rgmii.o cvmx-helper-sgmii.o cvmx-helper-npi.o \
+	cvmx-helper-loop.o cvmx-helper-spi.o cvmx-helper-util.o \
+	cvmx-interrupt-decodes.o cvmx-interrupt-rsl.o
+
+obj-y += cvmx-helper-errata.o cvmx-helper-jtag.o cvmx-boot-vector.o
diff --git a/arch/mips/cavium-octeon/executive/cvmx-boot-vector.c b/arch/mips/cavium-octeon/executive/cvmx-boot-vector.c
new file mode 100644
index 000000000..b7019d218
--- /dev/null
+++ b/arch/mips/cavium-octeon/executive/cvmx-boot-vector.c
@@ -0,0 +1,167 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2004-2017 Cavium, Inc.
+ */
+
+
+/*
+  We install this program at the bootvector:
+------------------------------------
+	.set noreorder
+	.set nomacro
+	.set noat
+reset_vector:
+	dmtc0	$k0, $31, 0	# Save $k0 to DESAVE
+	dmtc0	$k1, $31, 3	# Save $k1 to KScratch2
+
+	mfc0	$k0, $12, 0	# Status
+	mfc0	$k1, $15, 1	# Ebase
+
+	ori	$k0, 0x84	# Enable 64-bit addressing, set
+				# ERL (should already be set)
+	andi	$k1, 0x3ff	# mask out core ID
+
+	mtc0	$k0, $12, 0	# Status
+	sll	$k1, 5
+
+	lui	$k0, 0xbfc0
+	cache	17, 0($0)	# Core-14345, clear L1 Dcache virtual
+				# tags if the core hit an NMI
+
+	ld	$k0, 0x78($k0)	# k0 <- (bfc00078) pointer to the reset vector
+	synci	0($0)		# Invalidate ICache to get coherent
+				# view of target code.
+
+	daddu	$k0, $k0, $k1
+	nop
+
+	ld	$k0, 0($k0)	# k0 <- core specific target address
+	dmfc0	$k1, $31, 3	# Restore $k1 from KScratch2
+
+	beqz	$k0, wait_loop	# Spin in wait loop
+	nop
+
+	jr	$k0
+	nop
+
+	nop			# NOPs needed here to fill delay slots
+	nop			# on endian reversal of previous instructions
+
+wait_loop:
+	wait
+	nop
+
+	b	wait_loop
+	nop
+
+	nop
+	nop
+------------------------------------
+
+0000000000000000 <reset_vector>:
+   0:	40baf800	dmtc0	k0,c0_desave
+   4:	40bbf803	dmtc0	k1,c0_kscratch2
+
+   8:	401a6000	mfc0	k0,c0_status
+   c:	401b7801	mfc0	k1,c0_ebase
+
+  10:	375a0084	ori	k0,k0,0x84
+  14:	337b03ff	andi	k1,k1,0x3ff
+
+  18:	409a6000	mtc0	k0,c0_status
+  1c:	001bd940	sll	k1,k1,0x5
+
+  20:	3c1abfc0	lui	k0,0xbfc0
+  24:	bc110000	cache	0x11,0(zero)
+
+  28:	df5a0078	ld	k0,120(k0)
+  2c:	041f0000	synci	0(zero)
+
+  30:	035bd02d	daddu	k0,k0,k1
+  34:	00000000	nop
+
+  38:	df5a0000	ld	k0,0(k0)
+  3c:	403bf803	dmfc0	k1,c0_kscratch2
+
+  40:	13400005	beqz	k0,58 <wait_loop>
+  44:	00000000	nop
+
+  48:	03400008	jr	k0
+  4c:	00000000	nop
+
+  50:	00000000	nop
+  54:	00000000	nop
+
+0000000000000058 <wait_loop>:
+  58:	42000020	wait
+  5c:	00000000	nop
+
+  60:	1000fffd	b	58 <wait_loop>
+  64:	00000000	nop
+
+  68:	00000000	nop
+  6c:	00000000	nop
+
+ */
+
+#include <asm/octeon/cvmx-boot-vector.h>
+
+static unsigned long long _cvmx_bootvector_data[16] = {
+	0x40baf80040bbf803ull,  /* patch low order 8-bits if no KScratch*/
+	0x401a6000401b7801ull,
+	0x375a0084337b03ffull,
+	0x409a6000001bd940ull,
+	0x3c1abfc0bc110000ull,
+	0xdf5a0078041f0000ull,
+	0x035bd02d00000000ull,
+	0xdf5a0000403bf803ull,  /* patch low order 8-bits if no KScratch*/
+	0x1340000500000000ull,
+	0x0340000800000000ull,
+	0x0000000000000000ull,
+	0x4200002000000000ull,
+	0x1000fffd00000000ull,
+	0x0000000000000000ull,
+	OCTEON_BOOT_MOVEABLE_MAGIC1,
+	0 /* To be filled in with address of vector block*/
+};
+
+/* 2^10 CPUs */
+#define VECTOR_TABLE_SIZE (1024 * sizeof(struct cvmx_boot_vector_element))
+
+static void cvmx_boot_vector_init(void *mem)
+{
+	uint64_t kseg0_mem;
+	int i;
+
+	memset(mem, 0, VECTOR_TABLE_SIZE);
+	kseg0_mem = cvmx_ptr_to_phys(mem) | 0x8000000000000000ull;
+
+	for (i = 0; i < 15; i++) {
+		uint64_t v = _cvmx_bootvector_data[i];
+
+		if (OCTEON_IS_OCTEON1PLUS() && (i == 0 || i == 7))
+			v &= 0xffffffff00000000ull; /* KScratch not availble. */
+		cvmx_write_csr(CVMX_MIO_BOOT_LOC_ADR, i * 8);
+		cvmx_write_csr(CVMX_MIO_BOOT_LOC_DAT, v);
+	}
+	cvmx_write_csr(CVMX_MIO_BOOT_LOC_ADR, 15 * 8);
+	cvmx_write_csr(CVMX_MIO_BOOT_LOC_DAT, kseg0_mem);
+	cvmx_write_csr(CVMX_MIO_BOOT_LOC_CFGX(0), 0x81fc0000);
+}
+
+/**
+ * Get a pointer to the per-core table of reset vector pointers
+ *
+ */
+struct cvmx_boot_vector_element *cvmx_boot_vector_get(void)
+{
+	struct cvmx_boot_vector_element *ret;
+
+	ret = cvmx_bootmem_alloc_named_range_once(VECTOR_TABLE_SIZE, 0,
+		(1ull << 32) - 1, 8, "__boot_vector1__", cvmx_boot_vector_init);
+	return ret;
+}
+EXPORT_SYMBOL(cvmx_boot_vector_get);
diff --git a/arch/mips/cavium-octeon/executive/cvmx-bootmem.c b/arch/mips/cavium-octeon/executive/cvmx-bootmem.c
new file mode 100644
index 000000000..306cee07c
--- /dev/null
+++ b/arch/mips/cavium-octeon/executive/cvmx-bootmem.c
@@ -0,0 +1,796 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ * Simple allocate only memory allocator.  Used to allocate memory at
+ * application start time.
+ */
+
+#include <linux/export.h>
+#include <linux/kernel.h>
+
+#include <asm/octeon/cvmx.h>
+#include <asm/octeon/cvmx-spinlock.h>
+#include <asm/octeon/cvmx-bootmem.h>
+
+/*#define DEBUG */
+
+
+static struct cvmx_bootmem_desc *cvmx_bootmem_desc;
+
+/* See header file for descriptions of functions */
+
+/*
+ * This macro returns a member of the
+ * cvmx_bootmem_named_block_desc_t structure. These members can't
+ * be directly addressed as they might be in memory not directly
+ * reachable. In the case where bootmem is compiled with
+ * LINUX_HOST, the structure itself might be located on a remote
+ * Octeon. The argument "field" is the member name of the
+ * cvmx_bootmem_named_block_desc_t to read. Regardless of the type
+ * of the field, the return type is always a uint64_t. The "addr"
+ * parameter is the physical address of the structure.
+ */
+#define CVMX_BOOTMEM_NAMED_GET_FIELD(addr, field)			\
+	__cvmx_bootmem_desc_get(addr,					\
+		offsetof(struct cvmx_bootmem_named_block_desc, field),	\
+		sizeof_field(struct cvmx_bootmem_named_block_desc, field))
+
+/*
+ * This function is the implementation of the get macros defined
+ * for individual structure members. The argument are generated
+ * by the macros inorder to read only the needed memory.
+ *
+ * @param base   64bit physical address of the complete structure
+ * @param offset Offset from the beginning of the structure to the member being
+ *               accessed.
+ * @param size   Size of the structure member.
+ *
+ * @return Value of the structure member promoted into a uint64_t.
+ */
+static inline uint64_t __cvmx_bootmem_desc_get(uint64_t base, int offset,
+					       int size)
+{
+	base = (1ull << 63) | (base + offset);
+	switch (size) {
+	case 4:
+		return cvmx_read64_uint32(base);
+	case 8:
+		return cvmx_read64_uint64(base);
+	default:
+		return 0;
+	}
+}
+
+/*
+ * Wrapper functions are provided for reading/writing the size and
+ * next block values as these may not be directly addressible (in 32
+ * bit applications, for instance.)  Offsets of data elements in
+ * bootmem list, must match cvmx_bootmem_block_header_t.
+ */
+#define NEXT_OFFSET 0
+#define SIZE_OFFSET 8
+
+static void cvmx_bootmem_phy_set_size(uint64_t addr, uint64_t size)
+{
+	cvmx_write64_uint64((addr + SIZE_OFFSET) | (1ull << 63), size);
+}
+
+static void cvmx_bootmem_phy_set_next(uint64_t addr, uint64_t next)
+{
+	cvmx_write64_uint64((addr + NEXT_OFFSET) | (1ull << 63), next);
+}
+
+static uint64_t cvmx_bootmem_phy_get_size(uint64_t addr)
+{
+	return cvmx_read64_uint64((addr + SIZE_OFFSET) | (1ull << 63));
+}
+
+static uint64_t cvmx_bootmem_phy_get_next(uint64_t addr)
+{
+	return cvmx_read64_uint64((addr + NEXT_OFFSET) | (1ull << 63));
+}
+
+/*
+ * Allocate a block of memory from the free list that was
+ * passed to the application by the bootloader within a specified
+ * address range. This is an allocate-only algorithm, so
+ * freeing memory is not possible. Allocation will fail if
+ * memory cannot be allocated in the requested range.
+ *
+ * @size:      Size in bytes of block to allocate
+ * @min_addr:  defines the minimum address of the range
+ * @max_addr:  defines the maximum address of the range
+ * @alignment: Alignment required - must be power of 2
+ * Returns pointer to block of memory, NULL on error
+ */
+static void *cvmx_bootmem_alloc_range(uint64_t size, uint64_t alignment,
+				      uint64_t min_addr, uint64_t max_addr)
+{
+	int64_t address;
+	address =
+	    cvmx_bootmem_phy_alloc(size, min_addr, max_addr, alignment, 0);
+
+	if (address > 0)
+		return cvmx_phys_to_ptr(address);
+	else
+		return NULL;
+}
+
+void *cvmx_bootmem_alloc_address(uint64_t size, uint64_t address,
+				 uint64_t alignment)
+{
+	return cvmx_bootmem_alloc_range(size, alignment, address,
+					address + size);
+}
+
+void *cvmx_bootmem_alloc_named_range(uint64_t size, uint64_t min_addr,
+				     uint64_t max_addr, uint64_t align,
+				     char *name)
+{
+	int64_t addr;
+
+	addr = cvmx_bootmem_phy_named_block_alloc(size, min_addr, max_addr,
+						  align, name, 0);
+	if (addr >= 0)
+		return cvmx_phys_to_ptr(addr);
+	else
+		return NULL;
+}
+
+void *cvmx_bootmem_alloc_named(uint64_t size, uint64_t alignment, char *name)
+{
+    return cvmx_bootmem_alloc_named_range(size, 0, 0, alignment, name);
+}
+EXPORT_SYMBOL(cvmx_bootmem_alloc_named);
+
+void cvmx_bootmem_lock(void)
+{
+	cvmx_spinlock_lock((cvmx_spinlock_t *) &(cvmx_bootmem_desc->lock));
+}
+
+void cvmx_bootmem_unlock(void)
+{
+	cvmx_spinlock_unlock((cvmx_spinlock_t *) &(cvmx_bootmem_desc->lock));
+}
+
+int cvmx_bootmem_init(void *mem_desc_ptr)
+{
+	/* Here we set the global pointer to the bootmem descriptor
+	 * block.  This pointer will be used directly, so we will set
+	 * it up to be directly usable by the application.  It is set
+	 * up as follows for the various runtime/ABI combinations:
+	 *
+	 * Linux 64 bit: Set XKPHYS bit
+	 * Linux 32 bit: use mmap to create mapping, use virtual address
+	 * CVMX 64 bit:	 use physical address directly
+	 * CVMX 32 bit:	 use physical address directly
+	 *
+	 * Note that the CVMX environment assumes the use of 1-1 TLB
+	 * mappings so that the physical addresses can be used
+	 * directly
+	 */
+	if (!cvmx_bootmem_desc) {
+#if   defined(CVMX_ABI_64)
+		/* Set XKPHYS bit */
+		cvmx_bootmem_desc = cvmx_phys_to_ptr(CAST64(mem_desc_ptr));
+#else
+		cvmx_bootmem_desc = (struct cvmx_bootmem_desc *) mem_desc_ptr;
+#endif
+	}
+
+	return 0;
+}
+
+/*
+ * The cvmx_bootmem_phy* functions below return 64 bit physical
+ * addresses, and expose more features that the cvmx_bootmem_functions
+ * above.  These are required for full memory space access in 32 bit
+ * applications, as well as for using some advance features.  Most
+ * applications should not need to use these.
+ */
+
+int64_t cvmx_bootmem_phy_alloc(uint64_t req_size, uint64_t address_min,
+			       uint64_t address_max, uint64_t alignment,
+			       uint32_t flags)
+{
+
+	uint64_t head_addr;
+	uint64_t ent_addr;
+	/* points to previous list entry, NULL current entry is head of list */
+	uint64_t prev_addr = 0;
+	uint64_t new_ent_addr = 0;
+	uint64_t desired_min_addr;
+
+#ifdef DEBUG
+	cvmx_dprintf("cvmx_bootmem_phy_alloc: req_size: 0x%llx, "
+		     "min_addr: 0x%llx, max_addr: 0x%llx, align: 0x%llx\n",
+		     (unsigned long long)req_size,
+		     (unsigned long long)address_min,
+		     (unsigned long long)address_max,
+		     (unsigned long long)alignment);
+#endif
+
+	if (cvmx_bootmem_desc->major_version > 3) {
+		cvmx_dprintf("ERROR: Incompatible bootmem descriptor "
+			     "version: %d.%d at addr: %p\n",
+			     (int)cvmx_bootmem_desc->major_version,
+			     (int)cvmx_bootmem_desc->minor_version,
+			     cvmx_bootmem_desc);
+		goto error_out;
+	}
+
+	/*
+	 * Do a variety of checks to validate the arguments.  The
+	 * allocator code will later assume that these checks have
+	 * been made.  We validate that the requested constraints are
+	 * not self-contradictory before we look through the list of
+	 * available memory.
+	 */
+
+	/* 0 is not a valid req_size for this allocator */
+	if (!req_size)
+		goto error_out;
+
+	/* Round req_size up to mult of minimum alignment bytes */
+	req_size = (req_size + (CVMX_BOOTMEM_ALIGNMENT_SIZE - 1)) &
+		~(CVMX_BOOTMEM_ALIGNMENT_SIZE - 1);
+
+	/*
+	 * Convert !0 address_min and 0 address_max to special case of
+	 * range that specifies an exact memory block to allocate.  Do
+	 * this before other checks and adjustments so that this
+	 * tranformation will be validated.
+	 */
+	if (address_min && !address_max)
+		address_max = address_min + req_size;
+	else if (!address_min && !address_max)
+		address_max = ~0ull;  /* If no limits given, use max limits */
+
+
+	/*
+	 * Enforce minimum alignment (this also keeps the minimum free block
+	 * req_size the same as the alignment req_size.
+	 */
+	if (alignment < CVMX_BOOTMEM_ALIGNMENT_SIZE)
+		alignment = CVMX_BOOTMEM_ALIGNMENT_SIZE;
+
+	/*
+	 * Adjust address minimum based on requested alignment (round
+	 * up to meet alignment).  Do this here so we can reject
+	 * impossible requests up front. (NOP for address_min == 0)
+	 */
+	if (alignment)
+		address_min = ALIGN(address_min, alignment);
+
+	/*
+	 * Reject inconsistent args.  We have adjusted these, so this
+	 * may fail due to our internal changes even if this check
+	 * would pass for the values the user supplied.
+	 */
+	if (req_size > address_max - address_min)
+		goto error_out;
+
+	/* Walk through the list entries - first fit found is returned */
+
+	if (!(flags & CVMX_BOOTMEM_FLAG_NO_LOCKING))
+		cvmx_bootmem_lock();
+	head_addr = cvmx_bootmem_desc->head_addr;
+	ent_addr = head_addr;
+	for (; ent_addr;
+	     prev_addr = ent_addr,
+	     ent_addr = cvmx_bootmem_phy_get_next(ent_addr)) {
+		uint64_t usable_base, usable_max;
+		uint64_t ent_size = cvmx_bootmem_phy_get_size(ent_addr);
+
+		if (cvmx_bootmem_phy_get_next(ent_addr)
+		    && ent_addr > cvmx_bootmem_phy_get_next(ent_addr)) {
+			cvmx_dprintf("Internal bootmem_alloc() error: ent: "
+				"0x%llx, next: 0x%llx\n",
+				(unsigned long long)ent_addr,
+				(unsigned long long)
+				cvmx_bootmem_phy_get_next(ent_addr));
+			goto error_out;
+		}
+
+		/*
+		 * Determine if this is an entry that can satisfy the
+		 * request Check to make sure entry is large enough to
+		 * satisfy request.
+		 */
+		usable_base =
+		    ALIGN(max(address_min, ent_addr), alignment);
+		usable_max = min(address_max, ent_addr + ent_size);
+		/*
+		 * We should be able to allocate block at address
+		 * usable_base.
+		 */
+
+		desired_min_addr = usable_base;
+		/*
+		 * Determine if request can be satisfied from the
+		 * current entry.
+		 */
+		if (!((ent_addr + ent_size) > usable_base
+				&& ent_addr < address_max
+				&& req_size <= usable_max - usable_base))
+			continue;
+		/*
+		 * We have found an entry that has room to satisfy the
+		 * request, so allocate it from this entry.  If end
+		 * CVMX_BOOTMEM_FLAG_END_ALLOC set, then allocate from
+		 * the end of this block rather than the beginning.
+		 */
+		if (flags & CVMX_BOOTMEM_FLAG_END_ALLOC) {
+			desired_min_addr = usable_max - req_size;
+			/*
+			 * Align desired address down to required
+			 * alignment.
+			 */
+			desired_min_addr &= ~(alignment - 1);
+		}
+
+		/* Match at start of entry */
+		if (desired_min_addr == ent_addr) {
+			if (req_size < ent_size) {
+				/*
+				 * big enough to create a new block
+				 * from top portion of block.
+				 */
+				new_ent_addr = ent_addr + req_size;
+				cvmx_bootmem_phy_set_next(new_ent_addr,
+					cvmx_bootmem_phy_get_next(ent_addr));
+				cvmx_bootmem_phy_set_size(new_ent_addr,
+							ent_size -
+							req_size);
+
+				/*
+				 * Adjust next pointer as following
+				 * code uses this.
+				 */
+				cvmx_bootmem_phy_set_next(ent_addr,
+							new_ent_addr);
+			}
+
+			/*
+			 * adjust prev ptr or head to remove this
+			 * entry from list.
+			 */
+			if (prev_addr)
+				cvmx_bootmem_phy_set_next(prev_addr,
+					cvmx_bootmem_phy_get_next(ent_addr));
+			else
+				/*
+				 * head of list being returned, so
+				 * update head ptr.
+				 */
+				cvmx_bootmem_desc->head_addr =
+					cvmx_bootmem_phy_get_next(ent_addr);
+
+			if (!(flags & CVMX_BOOTMEM_FLAG_NO_LOCKING))
+				cvmx_bootmem_unlock();
+			return desired_min_addr;
+		}
+		/*
+		 * block returned doesn't start at beginning of entry,
+		 * so we know that we will be splitting a block off
+		 * the front of this one.  Create a new block from the
+		 * beginning, add to list, and go to top of loop
+		 * again.
+		 *
+		 * create new block from high portion of
+		 * block, so that top block starts at desired
+		 * addr.
+		 */
+		new_ent_addr = desired_min_addr;
+		cvmx_bootmem_phy_set_next(new_ent_addr,
+					cvmx_bootmem_phy_get_next
+					(ent_addr));
+		cvmx_bootmem_phy_set_size(new_ent_addr,
+					cvmx_bootmem_phy_get_size
+					(ent_addr) -
+					(desired_min_addr -
+						ent_addr));
+		cvmx_bootmem_phy_set_size(ent_addr,
+					desired_min_addr - ent_addr);
+		cvmx_bootmem_phy_set_next(ent_addr, new_ent_addr);
+		/* Loop again to handle actual alloc from new block */
+	}
+error_out:
+	/* We didn't find anything, so return error */
+	if (!(flags & CVMX_BOOTMEM_FLAG_NO_LOCKING))
+		cvmx_bootmem_unlock();
+	return -1;
+}
+
+int __cvmx_bootmem_phy_free(uint64_t phy_addr, uint64_t size, uint32_t flags)
+{
+	uint64_t cur_addr;
+	uint64_t prev_addr = 0; /* zero is invalid */
+	int retval = 0;
+
+#ifdef DEBUG
+	cvmx_dprintf("__cvmx_bootmem_phy_free addr: 0x%llx, size: 0x%llx\n",
+		     (unsigned long long)phy_addr, (unsigned long long)size);
+#endif
+	if (cvmx_bootmem_desc->major_version > 3) {
+		cvmx_dprintf("ERROR: Incompatible bootmem descriptor "
+			     "version: %d.%d at addr: %p\n",
+			     (int)cvmx_bootmem_desc->major_version,
+			     (int)cvmx_bootmem_desc->minor_version,
+			     cvmx_bootmem_desc);
+		return 0;
+	}
+
+	/* 0 is not a valid size for this allocator */
+	if (!size)
+		return 0;
+
+	if (!(flags & CVMX_BOOTMEM_FLAG_NO_LOCKING))
+		cvmx_bootmem_lock();
+	cur_addr = cvmx_bootmem_desc->head_addr;
+	if (cur_addr == 0 || phy_addr < cur_addr) {
+		/* add at front of list - special case with changing head ptr */
+		if (cur_addr && phy_addr + size > cur_addr)
+			goto bootmem_free_done; /* error, overlapping section */
+		else if (phy_addr + size == cur_addr) {
+			/* Add to front of existing first block */
+			cvmx_bootmem_phy_set_next(phy_addr,
+						  cvmx_bootmem_phy_get_next
+						  (cur_addr));
+			cvmx_bootmem_phy_set_size(phy_addr,
+						  cvmx_bootmem_phy_get_size
+						  (cur_addr) + size);
+			cvmx_bootmem_desc->head_addr = phy_addr;
+
+		} else {
+			/* New block before first block.  OK if cur_addr is 0 */
+			cvmx_bootmem_phy_set_next(phy_addr, cur_addr);
+			cvmx_bootmem_phy_set_size(phy_addr, size);
+			cvmx_bootmem_desc->head_addr = phy_addr;
+		}
+		retval = 1;
+		goto bootmem_free_done;
+	}
+
+	/* Find place in list to add block */
+	while (cur_addr && phy_addr > cur_addr) {
+		prev_addr = cur_addr;
+		cur_addr = cvmx_bootmem_phy_get_next(cur_addr);
+	}
+
+	if (!cur_addr) {
+		/*
+		 * We have reached the end of the list, add on to end,
+		 * checking to see if we need to combine with last
+		 * block
+		 */
+		if (prev_addr + cvmx_bootmem_phy_get_size(prev_addr) ==
+		    phy_addr) {
+			cvmx_bootmem_phy_set_size(prev_addr,
+						  cvmx_bootmem_phy_get_size
+						  (prev_addr) + size);
+		} else {
+			cvmx_bootmem_phy_set_next(prev_addr, phy_addr);
+			cvmx_bootmem_phy_set_size(phy_addr, size);
+			cvmx_bootmem_phy_set_next(phy_addr, 0);
+		}
+		retval = 1;
+		goto bootmem_free_done;
+	} else {
+		/*
+		 * insert between prev and cur nodes, checking for
+		 * merge with either/both.
+		 */
+		if (prev_addr + cvmx_bootmem_phy_get_size(prev_addr) ==
+		    phy_addr) {
+			/* Merge with previous */
+			cvmx_bootmem_phy_set_size(prev_addr,
+						  cvmx_bootmem_phy_get_size
+						  (prev_addr) + size);
+			if (phy_addr + size == cur_addr) {
+				/* Also merge with current */
+				cvmx_bootmem_phy_set_size(prev_addr,
+					cvmx_bootmem_phy_get_size(cur_addr) +
+					cvmx_bootmem_phy_get_size(prev_addr));
+				cvmx_bootmem_phy_set_next(prev_addr,
+					cvmx_bootmem_phy_get_next(cur_addr));
+			}
+			retval = 1;
+			goto bootmem_free_done;
+		} else if (phy_addr + size == cur_addr) {
+			/* Merge with current */
+			cvmx_bootmem_phy_set_size(phy_addr,
+						  cvmx_bootmem_phy_get_size
+						  (cur_addr) + size);
+			cvmx_bootmem_phy_set_next(phy_addr,
+						  cvmx_bootmem_phy_get_next
+						  (cur_addr));
+			cvmx_bootmem_phy_set_next(prev_addr, phy_addr);
+			retval = 1;
+			goto bootmem_free_done;
+		}
+
+		/* It is a standalone block, add in between prev and cur */
+		cvmx_bootmem_phy_set_size(phy_addr, size);
+		cvmx_bootmem_phy_set_next(phy_addr, cur_addr);
+		cvmx_bootmem_phy_set_next(prev_addr, phy_addr);
+
+	}
+	retval = 1;
+
+bootmem_free_done:
+	if (!(flags & CVMX_BOOTMEM_FLAG_NO_LOCKING))
+		cvmx_bootmem_unlock();
+	return retval;
+
+}
+
+/*
+ * Finds a named memory block by name.
+ * Also used for finding an unused entry in the named block table.
+ *
+ * @name: Name of memory block to find.	 If NULL pointer given, then
+ *	  finds unused descriptor, if available.
+ *
+ * @flags: Flags to control options for the allocation.
+ *
+ * Returns Pointer to memory block descriptor, NULL if not found.
+ *	   If NULL returned when name parameter is NULL, then no memory
+ *	   block descriptors are available.
+ */
+static struct cvmx_bootmem_named_block_desc *
+	cvmx_bootmem_phy_named_block_find(char *name, uint32_t flags)
+{
+	unsigned int i;
+	struct cvmx_bootmem_named_block_desc *named_block_array_ptr;
+
+#ifdef DEBUG
+	cvmx_dprintf("cvmx_bootmem_phy_named_block_find: %s\n", name);
+#endif
+	/*
+	 * Lock the structure to make sure that it is not being
+	 * changed while we are examining it.
+	 */
+	if (!(flags & CVMX_BOOTMEM_FLAG_NO_LOCKING))
+		cvmx_bootmem_lock();
+
+	/* Use XKPHYS for 64 bit linux */
+	named_block_array_ptr = (struct cvmx_bootmem_named_block_desc *)
+	    cvmx_phys_to_ptr(cvmx_bootmem_desc->named_block_array_addr);
+
+#ifdef DEBUG
+	cvmx_dprintf
+	    ("cvmx_bootmem_phy_named_block_find: named_block_array_ptr: %p\n",
+	     named_block_array_ptr);
+#endif
+	if (cvmx_bootmem_desc->major_version == 3) {
+		for (i = 0;
+		     i < cvmx_bootmem_desc->named_block_num_blocks; i++) {
+			if ((name && named_block_array_ptr[i].size
+			     && !strncmp(name, named_block_array_ptr[i].name,
+					 cvmx_bootmem_desc->named_block_name_len
+					 - 1))
+			    || (!name && !named_block_array_ptr[i].size)) {
+				if (!(flags & CVMX_BOOTMEM_FLAG_NO_LOCKING))
+					cvmx_bootmem_unlock();
+
+				return &(named_block_array_ptr[i]);
+			}
+		}
+	} else {
+		cvmx_dprintf("ERROR: Incompatible bootmem descriptor "
+			     "version: %d.%d at addr: %p\n",
+			     (int)cvmx_bootmem_desc->major_version,
+			     (int)cvmx_bootmem_desc->minor_version,
+			     cvmx_bootmem_desc);
+	}
+	if (!(flags & CVMX_BOOTMEM_FLAG_NO_LOCKING))
+		cvmx_bootmem_unlock();
+
+	return NULL;
+}
+
+void *cvmx_bootmem_alloc_named_range_once(uint64_t size, uint64_t min_addr,
+					  uint64_t max_addr, uint64_t align,
+					  char *name,
+					  void (*init) (void *))
+{
+	int64_t addr;
+	void *ptr;
+	uint64_t named_block_desc_addr;
+
+	named_block_desc_addr = (uint64_t)
+		cvmx_bootmem_phy_named_block_find(name,
+						  (uint32_t)CVMX_BOOTMEM_FLAG_NO_LOCKING);
+
+	if (named_block_desc_addr) {
+		addr = CVMX_BOOTMEM_NAMED_GET_FIELD(named_block_desc_addr,
+						    base_addr);
+		return cvmx_phys_to_ptr(addr);
+	}
+
+	addr = cvmx_bootmem_phy_named_block_alloc(size, min_addr, max_addr,
+						  align, name,
+						  (uint32_t)CVMX_BOOTMEM_FLAG_NO_LOCKING);
+
+	if (addr < 0)
+		return NULL;
+	ptr = cvmx_phys_to_ptr(addr);
+
+	if (init)
+		init(ptr);
+	else
+		memset(ptr, 0, size);
+
+	return ptr;
+}
+EXPORT_SYMBOL(cvmx_bootmem_alloc_named_range_once);
+
+struct cvmx_bootmem_named_block_desc *cvmx_bootmem_find_named_block(char *name)
+{
+	return cvmx_bootmem_phy_named_block_find(name, 0);
+}
+EXPORT_SYMBOL(cvmx_bootmem_find_named_block);
+
+/*
+ * Frees a named block.
+ *
+ * @name:   name of block to free
+ * @flags:  flags for passing options
+ *
+ * Returns 0 on failure
+ *	   1 on success
+ */
+static int cvmx_bootmem_phy_named_block_free(char *name, uint32_t flags)
+{
+	struct cvmx_bootmem_named_block_desc *named_block_ptr;
+
+	if (cvmx_bootmem_desc->major_version != 3) {
+		cvmx_dprintf("ERROR: Incompatible bootmem descriptor version: "
+			     "%d.%d at addr: %p\n",
+			     (int)cvmx_bootmem_desc->major_version,
+			     (int)cvmx_bootmem_desc->minor_version,
+			     cvmx_bootmem_desc);
+		return 0;
+	}
+#ifdef DEBUG
+	cvmx_dprintf("cvmx_bootmem_phy_named_block_free: %s\n", name);
+#endif
+
+	/*
+	 * Take lock here, as name lookup/block free/name free need to
+	 * be atomic.
+	 */
+	cvmx_bootmem_lock();
+
+	named_block_ptr =
+	    cvmx_bootmem_phy_named_block_find(name,
+					      CVMX_BOOTMEM_FLAG_NO_LOCKING);
+	if (named_block_ptr) {
+#ifdef DEBUG
+		cvmx_dprintf("cvmx_bootmem_phy_named_block_free: "
+			     "%s, base: 0x%llx, size: 0x%llx\n",
+			     name,
+			     (unsigned long long)named_block_ptr->base_addr,
+			     (unsigned long long)named_block_ptr->size);
+#endif
+		__cvmx_bootmem_phy_free(named_block_ptr->base_addr,
+					named_block_ptr->size,
+					CVMX_BOOTMEM_FLAG_NO_LOCKING);
+		named_block_ptr->size = 0;
+		/* Set size to zero to indicate block not used. */
+	}
+
+	cvmx_bootmem_unlock();
+	return named_block_ptr != NULL; /* 0 on failure, 1 on success */
+}
+
+int cvmx_bootmem_free_named(char *name)
+{
+	return cvmx_bootmem_phy_named_block_free(name, 0);
+}
+
+int64_t cvmx_bootmem_phy_named_block_alloc(uint64_t size, uint64_t min_addr,
+					   uint64_t max_addr,
+					   uint64_t alignment,
+					   char *name,
+					   uint32_t flags)
+{
+	int64_t addr_allocated;
+	struct cvmx_bootmem_named_block_desc *named_block_desc_ptr;
+
+#ifdef DEBUG
+	cvmx_dprintf("cvmx_bootmem_phy_named_block_alloc: size: 0x%llx, min: "
+		     "0x%llx, max: 0x%llx, align: 0x%llx, name: %s\n",
+		     (unsigned long long)size,
+		     (unsigned long long)min_addr,
+		     (unsigned long long)max_addr,
+		     (unsigned long long)alignment,
+		     name);
+#endif
+	if (cvmx_bootmem_desc->major_version != 3) {
+		cvmx_dprintf("ERROR: Incompatible bootmem descriptor version: "
+			     "%d.%d at addr: %p\n",
+			     (int)cvmx_bootmem_desc->major_version,
+			     (int)cvmx_bootmem_desc->minor_version,
+			     cvmx_bootmem_desc);
+		return -1;
+	}
+
+	/*
+	 * Take lock here, as name lookup/block alloc/name add need to
+	 * be atomic.
+	 */
+	if (!(flags & CVMX_BOOTMEM_FLAG_NO_LOCKING))
+		cvmx_spinlock_lock((cvmx_spinlock_t *)&(cvmx_bootmem_desc->lock));
+
+	/* Get pointer to first available named block descriptor */
+	named_block_desc_ptr =
+		cvmx_bootmem_phy_named_block_find(NULL,
+						  flags | CVMX_BOOTMEM_FLAG_NO_LOCKING);
+
+	/*
+	 * Check to see if name already in use, return error if name
+	 * not available or no more room for blocks.
+	 */
+	if (cvmx_bootmem_phy_named_block_find(name,
+					      flags | CVMX_BOOTMEM_FLAG_NO_LOCKING) || !named_block_desc_ptr) {
+		if (!(flags & CVMX_BOOTMEM_FLAG_NO_LOCKING))
+			cvmx_spinlock_unlock((cvmx_spinlock_t *)&(cvmx_bootmem_desc->lock));
+		return -1;
+	}
+
+
+	/*
+	 * Round size up to mult of minimum alignment bytes We need
+	 * the actual size allocated to allow for blocks to be
+	 * coalesced when they are freed. The alloc routine does the
+	 * same rounding up on all allocations.
+	 */
+	size = ALIGN(size, CVMX_BOOTMEM_ALIGNMENT_SIZE);
+
+	addr_allocated = cvmx_bootmem_phy_alloc(size, min_addr, max_addr,
+						alignment,
+						flags | CVMX_BOOTMEM_FLAG_NO_LOCKING);
+	if (addr_allocated >= 0) {
+		named_block_desc_ptr->base_addr = addr_allocated;
+		named_block_desc_ptr->size = size;
+		strncpy(named_block_desc_ptr->name, name,
+			cvmx_bootmem_desc->named_block_name_len);
+		named_block_desc_ptr->name[cvmx_bootmem_desc->named_block_name_len - 1] = 0;
+	}
+
+	if (!(flags & CVMX_BOOTMEM_FLAG_NO_LOCKING))
+		cvmx_spinlock_unlock((cvmx_spinlock_t *)&(cvmx_bootmem_desc->lock));
+	return addr_allocated;
+}
+
+struct cvmx_bootmem_desc *cvmx_bootmem_get_desc(void)
+{
+	return cvmx_bootmem_desc;
+}
diff --git a/arch/mips/cavium-octeon/executive/cvmx-cmd-queue.c b/arch/mips/cavium-octeon/executive/cvmx-cmd-queue.c
new file mode 100644
index 000000000..aa7bbf8d0
--- /dev/null
+++ b/arch/mips/cavium-octeon/executive/cvmx-cmd-queue.c
@@ -0,0 +1,303 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ * Support functions for managing command queues used for
+ * various hardware blocks.
+ */
+
+#include <linux/kernel.h>
+
+#include <asm/octeon/octeon.h>
+
+#include <asm/octeon/cvmx-config.h>
+#include <asm/octeon/cvmx-fpa.h>
+#include <asm/octeon/cvmx-cmd-queue.h>
+
+#include <asm/octeon/cvmx-npei-defs.h>
+#include <asm/octeon/cvmx-pexp-defs.h>
+#include <asm/octeon/cvmx-pko-defs.h>
+
+/*
+ * This application uses this pointer to access the global queue
+ * state. It points to a bootmem named block.
+ */
+__cvmx_cmd_queue_all_state_t *__cvmx_cmd_queue_state_ptr;
+EXPORT_SYMBOL_GPL(__cvmx_cmd_queue_state_ptr);
+
+/*
+ * Initialize the Global queue state pointer.
+ *
+ * Returns CVMX_CMD_QUEUE_SUCCESS or a failure code
+ */
+static cvmx_cmd_queue_result_t __cvmx_cmd_queue_init_state_ptr(void)
+{
+	char *alloc_name = "cvmx_cmd_queues";
+	extern uint64_t octeon_reserve32_memory;
+
+	if (likely(__cvmx_cmd_queue_state_ptr))
+		return CVMX_CMD_QUEUE_SUCCESS;
+
+	if (octeon_reserve32_memory)
+		__cvmx_cmd_queue_state_ptr =
+		    cvmx_bootmem_alloc_named_range(sizeof(*__cvmx_cmd_queue_state_ptr),
+						   octeon_reserve32_memory,
+						   octeon_reserve32_memory +
+						   (CONFIG_CAVIUM_RESERVE32 <<
+						    20) - 1, 128, alloc_name);
+	else
+		__cvmx_cmd_queue_state_ptr =
+		    cvmx_bootmem_alloc_named(sizeof(*__cvmx_cmd_queue_state_ptr),
+					    128,
+					    alloc_name);
+	if (__cvmx_cmd_queue_state_ptr)
+		memset(__cvmx_cmd_queue_state_ptr, 0,
+		       sizeof(*__cvmx_cmd_queue_state_ptr));
+	else {
+		struct cvmx_bootmem_named_block_desc *block_desc =
+		    cvmx_bootmem_find_named_block(alloc_name);
+		if (block_desc)
+			__cvmx_cmd_queue_state_ptr =
+			    cvmx_phys_to_ptr(block_desc->base_addr);
+		else {
+			cvmx_dprintf
+			    ("ERROR: cvmx_cmd_queue_initialize: Unable to get named block %s.\n",
+			     alloc_name);
+			return CVMX_CMD_QUEUE_NO_MEMORY;
+		}
+	}
+	return CVMX_CMD_QUEUE_SUCCESS;
+}
+
+/*
+ * Initialize a command queue for use. The initial FPA buffer is
+ * allocated and the hardware unit is configured to point to the
+ * new command queue.
+ *
+ * @queue_id:  Hardware command queue to initialize.
+ * @max_depth: Maximum outstanding commands that can be queued.
+ * @fpa_pool:  FPA pool the command queues should come from.
+ * @pool_size: Size of each buffer in the FPA pool (bytes)
+ *
+ * Returns CVMX_CMD_QUEUE_SUCCESS or a failure code
+ */
+cvmx_cmd_queue_result_t cvmx_cmd_queue_initialize(cvmx_cmd_queue_id_t queue_id,
+						  int max_depth, int fpa_pool,
+						  int pool_size)
+{
+	__cvmx_cmd_queue_state_t *qstate;
+	cvmx_cmd_queue_result_t result = __cvmx_cmd_queue_init_state_ptr();
+	if (result != CVMX_CMD_QUEUE_SUCCESS)
+		return result;
+
+	qstate = __cvmx_cmd_queue_get_state(queue_id);
+	if (qstate == NULL)
+		return CVMX_CMD_QUEUE_INVALID_PARAM;
+
+	/*
+	 * We artificially limit max_depth to 1<<20 words. It is an
+	 * arbitrary limit.
+	 */
+	if (CVMX_CMD_QUEUE_ENABLE_MAX_DEPTH) {
+		if ((max_depth < 0) || (max_depth > 1 << 20))
+			return CVMX_CMD_QUEUE_INVALID_PARAM;
+	} else if (max_depth != 0)
+		return CVMX_CMD_QUEUE_INVALID_PARAM;
+
+	if ((fpa_pool < 0) || (fpa_pool > 7))
+		return CVMX_CMD_QUEUE_INVALID_PARAM;
+	if ((pool_size < 128) || (pool_size > 65536))
+		return CVMX_CMD_QUEUE_INVALID_PARAM;
+
+	/* See if someone else has already initialized the queue */
+	if (qstate->base_ptr_div128) {
+		if (max_depth != (int)qstate->max_depth) {
+			cvmx_dprintf("ERROR: cvmx_cmd_queue_initialize: "
+				"Queue already initialized with different "
+				"max_depth (%d).\n",
+			     (int)qstate->max_depth);
+			return CVMX_CMD_QUEUE_INVALID_PARAM;
+		}
+		if (fpa_pool != qstate->fpa_pool) {
+			cvmx_dprintf("ERROR: cvmx_cmd_queue_initialize: "
+				"Queue already initialized with different "
+				"FPA pool (%u).\n",
+			     qstate->fpa_pool);
+			return CVMX_CMD_QUEUE_INVALID_PARAM;
+		}
+		if ((pool_size >> 3) - 1 != qstate->pool_size_m1) {
+			cvmx_dprintf("ERROR: cvmx_cmd_queue_initialize: "
+				"Queue already initialized with different "
+				"FPA pool size (%u).\n",
+			     (qstate->pool_size_m1 + 1) << 3);
+			return CVMX_CMD_QUEUE_INVALID_PARAM;
+		}
+		CVMX_SYNCWS;
+		return CVMX_CMD_QUEUE_ALREADY_SETUP;
+	} else {
+		union cvmx_fpa_ctl_status status;
+		void *buffer;
+
+		status.u64 = cvmx_read_csr(CVMX_FPA_CTL_STATUS);
+		if (!status.s.enb) {
+			cvmx_dprintf("ERROR: cvmx_cmd_queue_initialize: "
+				     "FPA is not enabled.\n");
+			return CVMX_CMD_QUEUE_NO_MEMORY;
+		}
+		buffer = cvmx_fpa_alloc(fpa_pool);
+		if (buffer == NULL) {
+			cvmx_dprintf("ERROR: cvmx_cmd_queue_initialize: "
+				     "Unable to allocate initial buffer.\n");
+			return CVMX_CMD_QUEUE_NO_MEMORY;
+		}
+
+		memset(qstate, 0, sizeof(*qstate));
+		qstate->max_depth = max_depth;
+		qstate->fpa_pool = fpa_pool;
+		qstate->pool_size_m1 = (pool_size >> 3) - 1;
+		qstate->base_ptr_div128 = cvmx_ptr_to_phys(buffer) / 128;
+		/*
+		 * We zeroed the now serving field so we need to also
+		 * zero the ticket.
+		 */
+		__cvmx_cmd_queue_state_ptr->
+		    ticket[__cvmx_cmd_queue_get_index(queue_id)] = 0;
+		CVMX_SYNCWS;
+		return CVMX_CMD_QUEUE_SUCCESS;
+	}
+}
+
+/*
+ * Shutdown a queue a free it's command buffers to the FPA. The
+ * hardware connected to the queue must be stopped before this
+ * function is called.
+ *
+ * @queue_id: Queue to shutdown
+ *
+ * Returns CVMX_CMD_QUEUE_SUCCESS or a failure code
+ */
+cvmx_cmd_queue_result_t cvmx_cmd_queue_shutdown(cvmx_cmd_queue_id_t queue_id)
+{
+	__cvmx_cmd_queue_state_t *qptr = __cvmx_cmd_queue_get_state(queue_id);
+	if (qptr == NULL) {
+		cvmx_dprintf("ERROR: cvmx_cmd_queue_shutdown: Unable to "
+			     "get queue information.\n");
+		return CVMX_CMD_QUEUE_INVALID_PARAM;
+	}
+
+	if (cvmx_cmd_queue_length(queue_id) > 0) {
+		cvmx_dprintf("ERROR: cvmx_cmd_queue_shutdown: Queue still "
+			     "has data in it.\n");
+		return CVMX_CMD_QUEUE_FULL;
+	}
+
+	__cvmx_cmd_queue_lock(queue_id, qptr);
+	if (qptr->base_ptr_div128) {
+		cvmx_fpa_free(cvmx_phys_to_ptr
+			      ((uint64_t) qptr->base_ptr_div128 << 7),
+			      qptr->fpa_pool, 0);
+		qptr->base_ptr_div128 = 0;
+	}
+	__cvmx_cmd_queue_unlock(qptr);
+
+	return CVMX_CMD_QUEUE_SUCCESS;
+}
+
+/*
+ * Return the number of command words pending in the queue. This
+ * function may be relatively slow for some hardware units.
+ *
+ * @queue_id: Hardware command queue to query
+ *
+ * Returns Number of outstanding commands
+ */
+int cvmx_cmd_queue_length(cvmx_cmd_queue_id_t queue_id)
+{
+	if (CVMX_ENABLE_PARAMETER_CHECKING) {
+		if (__cvmx_cmd_queue_get_state(queue_id) == NULL)
+			return CVMX_CMD_QUEUE_INVALID_PARAM;
+	}
+
+	/*
+	 * The cast is here so gcc with check that all values in the
+	 * cvmx_cmd_queue_id_t enumeration are here.
+	 */
+	switch ((cvmx_cmd_queue_id_t) (queue_id & 0xff0000)) {
+	case CVMX_CMD_QUEUE_PKO_BASE:
+		/*
+		 * FIXME: Need atomic lock on
+		 * CVMX_PKO_REG_READ_IDX. Right now we are normally
+		 * called with the queue lock, so that is a SLIGHT
+		 * amount of protection.
+		 */
+		cvmx_write_csr(CVMX_PKO_REG_READ_IDX, queue_id & 0xffff);
+		if (OCTEON_IS_MODEL(OCTEON_CN3XXX)) {
+			union cvmx_pko_mem_debug9 debug9;
+			debug9.u64 = cvmx_read_csr(CVMX_PKO_MEM_DEBUG9);
+			return debug9.cn38xx.doorbell;
+		} else {
+			union cvmx_pko_mem_debug8 debug8;
+			debug8.u64 = cvmx_read_csr(CVMX_PKO_MEM_DEBUG8);
+			return debug8.cn50xx.doorbell;
+		}
+	case CVMX_CMD_QUEUE_ZIP:
+	case CVMX_CMD_QUEUE_DFA:
+	case CVMX_CMD_QUEUE_RAID:
+		/* FIXME: Implement other lengths */
+		return 0;
+	case CVMX_CMD_QUEUE_DMA_BASE:
+		{
+			union cvmx_npei_dmax_counts dmax_counts;
+			dmax_counts.u64 =
+			    cvmx_read_csr(CVMX_PEXP_NPEI_DMAX_COUNTS
+					  (queue_id & 0x7));
+			return dmax_counts.s.dbell;
+		}
+	case CVMX_CMD_QUEUE_END:
+		return CVMX_CMD_QUEUE_INVALID_PARAM;
+	}
+	return CVMX_CMD_QUEUE_INVALID_PARAM;
+}
+
+/*
+ * Return the command buffer to be written to. The purpose of this
+ * function is to allow CVMX routine access t othe low level buffer
+ * for initial hardware setup. User applications should not call this
+ * function directly.
+ *
+ * @queue_id: Command queue to query
+ *
+ * Returns Command buffer or NULL on failure
+ */
+void *cvmx_cmd_queue_buffer(cvmx_cmd_queue_id_t queue_id)
+{
+	__cvmx_cmd_queue_state_t *qptr = __cvmx_cmd_queue_get_state(queue_id);
+	if (qptr && qptr->base_ptr_div128)
+		return cvmx_phys_to_ptr((uint64_t) qptr->base_ptr_div128 << 7);
+	else
+		return NULL;
+}
diff --git a/arch/mips/cavium-octeon/executive/cvmx-helper-board.c b/arch/mips/cavium-octeon/executive/cvmx-helper-board.c
new file mode 100644
index 000000000..0fd9ac76e
--- /dev/null
+++ b/arch/mips/cavium-octeon/executive/cvmx-helper-board.c
@@ -0,0 +1,348 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ *
+ * Helper functions to abstract board specific data about
+ * network ports from the rest of the cvmx-helper files.
+ */
+
+#include <linux/bug.h>
+#include <asm/octeon/octeon.h>
+#include <asm/octeon/cvmx-bootinfo.h>
+
+#include <asm/octeon/cvmx-config.h>
+
+#include <asm/octeon/cvmx-helper.h>
+#include <asm/octeon/cvmx-helper-util.h>
+#include <asm/octeon/cvmx-helper-board.h>
+
+#include <asm/octeon/cvmx-gmxx-defs.h>
+#include <asm/octeon/cvmx-asxx-defs.h>
+
+/*
+ * Return the MII PHY address associated with the given IPD
+ * port. A result of -1 means there isn't a MII capable PHY
+ * connected to this port. On chips supporting multiple MII
+ * busses the bus number is encoded in bits <15:8>.
+ *
+ * This function must be modified for every new Octeon board.
+ * Internally it uses switch statements based on the cvmx_sysinfo
+ * data to determine board types and revisions. It replies on the
+ * fact that every Octeon board receives a unique board type
+ * enumeration from the bootloader.
+ *
+ * @ipd_port: Octeon IPD port to get the MII address for.
+ *
+ * Returns MII PHY address and bus number or -1.
+ */
+int cvmx_helper_board_get_mii_address(int ipd_port)
+{
+	switch (cvmx_sysinfo_get()->board_type) {
+	case CVMX_BOARD_TYPE_SIM:
+		/* Simulator doesn't have MII */
+		return -1;
+	case CVMX_BOARD_TYPE_EBT3000:
+	case CVMX_BOARD_TYPE_EBT5800:
+	case CVMX_BOARD_TYPE_THUNDER:
+	case CVMX_BOARD_TYPE_NICPRO2:
+		/* Interface 0 is SPI4, interface 1 is RGMII */
+		if ((ipd_port >= 16) && (ipd_port < 20))
+			return ipd_port - 16;
+		else
+			return -1;
+	case CVMX_BOARD_TYPE_KODAMA:
+	case CVMX_BOARD_TYPE_EBH3100:
+	case CVMX_BOARD_TYPE_HIKARI:
+	case CVMX_BOARD_TYPE_CN3010_EVB_HS5:
+	case CVMX_BOARD_TYPE_CN3005_EVB_HS5:
+	case CVMX_BOARD_TYPE_CN3020_EVB_HS5:
+		/*
+		 * Port 0 is WAN connected to a PHY, Port 1 is GMII
+		 * connected to a switch
+		 */
+		if (ipd_port == 0)
+			return 4;
+		else if (ipd_port == 1)
+			return 9;
+		else
+			return -1;
+	case CVMX_BOARD_TYPE_NAC38:
+		/* Board has 8 RGMII ports PHYs are 0-7 */
+		if ((ipd_port >= 0) && (ipd_port < 4))
+			return ipd_port;
+		else if ((ipd_port >= 16) && (ipd_port < 20))
+			return ipd_port - 16 + 4;
+		else
+			return -1;
+	case CVMX_BOARD_TYPE_EBH3000:
+		/* Board has dual SPI4 and no PHYs */
+		return -1;
+	case CVMX_BOARD_TYPE_EBH5200:
+	case CVMX_BOARD_TYPE_EBH5201:
+	case CVMX_BOARD_TYPE_EBT5200:
+		/* Board has 2 management ports */
+		if ((ipd_port >= CVMX_HELPER_BOARD_MGMT_IPD_PORT) &&
+		    (ipd_port < (CVMX_HELPER_BOARD_MGMT_IPD_PORT + 2)))
+			return ipd_port - CVMX_HELPER_BOARD_MGMT_IPD_PORT;
+		/*
+		 * Board has 4 SGMII ports. The PHYs start right after the MII
+		 * ports MII0 = 0, MII1 = 1, SGMII = 2-5.
+		 */
+		if ((ipd_port >= 0) && (ipd_port < 4))
+			return ipd_port + 2;
+		else
+			return -1;
+	case CVMX_BOARD_TYPE_EBH5600:
+	case CVMX_BOARD_TYPE_EBH5601:
+	case CVMX_BOARD_TYPE_EBH5610:
+		/* Board has 1 management port */
+		if (ipd_port == CVMX_HELPER_BOARD_MGMT_IPD_PORT)
+			return 0;
+		/*
+		 * Board has 8 SGMII ports. 4 connect out, two connect
+		 * to a switch, and 2 loop to each other
+		 */
+		if ((ipd_port >= 0) && (ipd_port < 4))
+			return ipd_port + 1;
+		else
+			return -1;
+	case CVMX_BOARD_TYPE_CUST_NB5:
+		if (ipd_port == 2)
+			return 4;
+		else
+			return -1;
+	case CVMX_BOARD_TYPE_NIC_XLE_4G:
+		/* Board has 4 SGMII ports. connected QLM3(interface 1) */
+		if ((ipd_port >= 16) && (ipd_port < 20))
+			return ipd_port - 16 + 1;
+		else
+			return -1;
+	case CVMX_BOARD_TYPE_NIC_XLE_10G:
+	case CVMX_BOARD_TYPE_NIC10E:
+		return -1;
+	case CVMX_BOARD_TYPE_NIC4E:
+		if (ipd_port >= 0 && ipd_port <= 3)
+			return (ipd_port + 0x1f) & 0x1f;
+		else
+			return -1;
+	case CVMX_BOARD_TYPE_NIC2E:
+		if (ipd_port >= 0 && ipd_port <= 1)
+			return ipd_port + 1;
+		else
+			return -1;
+	case CVMX_BOARD_TYPE_BBGW_REF:
+		/*
+		 * No PHYs are connected to Octeon, everything is
+		 * through switch.
+		 */
+		return -1;
+
+	case CVMX_BOARD_TYPE_CUST_WSX16:
+		if (ipd_port >= 0 && ipd_port <= 3)
+			return ipd_port;
+		else if (ipd_port >= 16 && ipd_port <= 19)
+			return ipd_port - 16 + 4;
+		else
+			return -1;
+	case CVMX_BOARD_TYPE_UBNT_E100:
+		if (ipd_port >= 0 && ipd_port <= 2)
+			return 7 - ipd_port;
+		else
+			return -1;
+	case CVMX_BOARD_TYPE_KONTRON_S1901:
+		if (ipd_port == CVMX_HELPER_BOARD_MGMT_IPD_PORT)
+			return 1;
+		else
+			return -1;
+
+	}
+
+	/* Some unknown board. Somebody forgot to update this function... */
+	cvmx_dprintf
+	    ("cvmx_helper_board_get_mii_address: Unknown board type %d\n",
+	     cvmx_sysinfo_get()->board_type);
+	return -1;
+}
+
+/*
+ * This function is the board specific method of determining an
+ * ethernet ports link speed. Most Octeon boards have Marvell PHYs
+ * and are handled by the fall through case. This function must be
+ * updated for boards that don't have the normal Marvell PHYs.
+ *
+ * This function must be modified for every new Octeon board.
+ * Internally it uses switch statements based on the cvmx_sysinfo
+ * data to determine board types and revisions. It relies on the
+ * fact that every Octeon board receives a unique board type
+ * enumeration from the bootloader.
+ *
+ * @ipd_port: IPD input port associated with the port we want to get link
+ *		   status for.
+ *
+ * Returns The ports link status. If the link isn't fully resolved, this must
+ *	   return zero.
+ */
+union cvmx_helper_link_info __cvmx_helper_board_link_get(int ipd_port)
+{
+	union cvmx_helper_link_info result;
+
+	WARN_ONCE(!octeon_is_simulation(),
+	     "Using deprecated link status - please update your DT");
+
+	/* Unless we fix it later, all links are defaulted to down */
+	result.u64 = 0;
+
+	if (octeon_is_simulation()) {
+		/* The simulator gives you a simulated 1Gbps full duplex link */
+		result.s.link_up = 1;
+		result.s.full_duplex = 1;
+		result.s.speed = 1000;
+		return result;
+	}
+
+	if (OCTEON_IS_MODEL(OCTEON_CN3XXX)
+		   || OCTEON_IS_MODEL(OCTEON_CN58XX)
+		   || OCTEON_IS_MODEL(OCTEON_CN50XX)) {
+		/*
+		 * We don't have a PHY address, so attempt to use
+		 * in-band status. It is really important that boards
+		 * not supporting in-band status never get
+		 * here. Reading broken in-band status tends to do bad
+		 * things
+		 */
+		union cvmx_gmxx_rxx_rx_inbnd inband_status;
+		int interface = cvmx_helper_get_interface_num(ipd_port);
+		int index = cvmx_helper_get_interface_index_num(ipd_port);
+		inband_status.u64 =
+		    cvmx_read_csr(CVMX_GMXX_RXX_RX_INBND(index, interface));
+
+		result.s.link_up = inband_status.s.status;
+		result.s.full_duplex = inband_status.s.duplex;
+		switch (inband_status.s.speed) {
+		case 0: /* 10 Mbps */
+			result.s.speed = 10;
+			break;
+		case 1: /* 100 Mbps */
+			result.s.speed = 100;
+			break;
+		case 2: /* 1 Gbps */
+			result.s.speed = 1000;
+			break;
+		case 3: /* Illegal */
+			result.u64 = 0;
+			break;
+		}
+	} else {
+		/*
+		 * We don't have a PHY address and we don't have
+		 * in-band status. There is no way to determine the
+		 * link speed. Return down assuming this port isn't
+		 * wired
+		 */
+		result.u64 = 0;
+	}
+
+	/* If link is down, return all fields as zero. */
+	if (!result.s.link_up)
+		result.u64 = 0;
+
+	return result;
+}
+
+/*
+ * This function is called by cvmx_helper_interface_probe() after it
+ * determines the number of ports Octeon can support on a specific
+ * interface. This function is the per board location to override
+ * this value. It is called with the number of ports Octeon might
+ * support and should return the number of actual ports on the
+ * board.
+ *
+ * This function must be modified for every new Octeon board.
+ * Internally it uses switch statements based on the cvmx_sysinfo
+ * data to determine board types and revisions. It relies on the
+ * fact that every Octeon board receives a unique board type
+ * enumeration from the bootloader.
+ *
+ * @interface: Interface to probe
+ * @supported_ports:
+ *		    Number of ports Octeon supports.
+ *
+ * Returns Number of ports the actual board supports. Many times this will
+ *	   simple be "support_ports".
+ */
+int __cvmx_helper_board_interface_probe(int interface, int supported_ports)
+{
+	switch (cvmx_sysinfo_get()->board_type) {
+	case CVMX_BOARD_TYPE_CN3005_EVB_HS5:
+		if (interface == 0)
+			return 2;
+		break;
+	case CVMX_BOARD_TYPE_BBGW_REF:
+		if (interface == 0)
+			return 2;
+		break;
+	case CVMX_BOARD_TYPE_NIC_XLE_4G:
+		if (interface == 0)
+			return 0;
+		break;
+		/* The 2nd interface on the EBH5600 is connected to the Marvel switch,
+		   which we don't support. Disable ports connected to it */
+	case CVMX_BOARD_TYPE_EBH5600:
+		if (interface == 1)
+			return 0;
+		break;
+	}
+	return supported_ports;
+}
+
+/*
+ * Get the clock type used for the USB block based on board type.
+ * Used by the USB code for auto configuration of clock type.
+ *
+ * Return USB clock type enumeration
+ */
+enum cvmx_helper_board_usb_clock_types __cvmx_helper_board_usb_get_clock_type(void)
+{
+	switch (cvmx_sysinfo_get()->board_type) {
+	case CVMX_BOARD_TYPE_BBGW_REF:
+	case CVMX_BOARD_TYPE_LANAI2_A:
+	case CVMX_BOARD_TYPE_LANAI2_U:
+	case CVMX_BOARD_TYPE_LANAI2_G:
+	case CVMX_BOARD_TYPE_NIC10E_66:
+	case CVMX_BOARD_TYPE_UBNT_E100:
+		return USB_CLOCK_TYPE_CRYSTAL_12;
+	case CVMX_BOARD_TYPE_NIC10E:
+		return USB_CLOCK_TYPE_REF_12;
+	default:
+		break;
+	}
+	/* Most boards except NIC10e use a 12MHz crystal */
+	if (OCTEON_IS_OCTEON2())
+		return USB_CLOCK_TYPE_CRYSTAL_12;
+	return USB_CLOCK_TYPE_REF_48;
+}
diff --git a/arch/mips/cavium-octeon/executive/cvmx-helper-errata.c b/arch/mips/cavium-octeon/executive/cvmx-helper-errata.c
new file mode 100644
index 000000000..4b26fedec
--- /dev/null
+++ b/arch/mips/cavium-octeon/executive/cvmx-helper-errata.c
@@ -0,0 +1,73 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/**
+ *
+ * Fixes and workaround for Octeon chip errata. This file
+ * contains functions called by cvmx-helper to workaround known
+ * chip errata. For the most part, code doesn't need to call
+ * these functions directly.
+ *
+ */
+#include <linux/export.h>
+
+#include <asm/octeon/octeon.h>
+
+#include <asm/octeon/cvmx-helper-jtag.h>
+
+/**
+ * Due to errata G-720, the 2nd order CDR circuit on CN52XX pass
+ * 1 doesn't work properly. The following code disables 2nd order
+ * CDR for the specified QLM.
+ *
+ * @qlm:    QLM to disable 2nd order CDR for.
+ */
+void __cvmx_helper_errata_qlm_disable_2nd_order_cdr(int qlm)
+{
+	int lane;
+	cvmx_helper_qlm_jtag_init();
+	/* We need to load all four lanes of the QLM, a total of 1072 bits */
+	for (lane = 0; lane < 4; lane++) {
+		/*
+		 * Each lane has 268 bits. We need to set
+		 * cfg_cdr_incx<67:64> = 3 and cfg_cdr_secord<77> =
+		 * 1. All other bits are zero. Bits go in LSB first,
+		 * so start off with the zeros for bits <63:0>.
+		 */
+		cvmx_helper_qlm_jtag_shift_zeros(qlm, 63 - 0 + 1);
+		/* cfg_cdr_incx<67:64>=3 */
+		cvmx_helper_qlm_jtag_shift(qlm, 67 - 64 + 1, 3);
+		/* Zeros for bits <76:68> */
+		cvmx_helper_qlm_jtag_shift_zeros(qlm, 76 - 68 + 1);
+		/* cfg_cdr_secord<77>=1 */
+		cvmx_helper_qlm_jtag_shift(qlm, 77 - 77 + 1, 1);
+		/* Zeros for bits <267:78> */
+		cvmx_helper_qlm_jtag_shift_zeros(qlm, 267 - 78 + 1);
+	}
+	cvmx_helper_qlm_jtag_update(qlm);
+}
+EXPORT_SYMBOL(__cvmx_helper_errata_qlm_disable_2nd_order_cdr);
diff --git a/arch/mips/cavium-octeon/executive/cvmx-helper-jtag.c b/arch/mips/cavium-octeon/executive/cvmx-helper-jtag.c
new file mode 100644
index 000000000..607b4e659
--- /dev/null
+++ b/arch/mips/cavium-octeon/executive/cvmx-helper-jtag.c
@@ -0,0 +1,144 @@
+
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/**
+ *
+ * Helper utilities for qlm_jtag.
+ *
+ */
+
+#include <asm/octeon/octeon.h>
+#include <asm/octeon/cvmx-helper-jtag.h>
+
+
+/**
+ * Initialize the internal QLM JTAG logic to allow programming
+ * of the JTAG chain by the cvmx_helper_qlm_jtag_*() functions.
+ * These functions should only be used at the direction of Cavium
+ * Networks. Programming incorrect values into the JTAG chain
+ * can cause chip damage.
+ */
+void cvmx_helper_qlm_jtag_init(void)
+{
+	union cvmx_ciu_qlm_jtgc jtgc;
+	uint32_t clock_div = 0;
+	uint32_t divisor = cvmx_sysinfo_get()->cpu_clock_hz / (25 * 1000000);
+	divisor = (divisor - 1) >> 2;
+	/* Convert the divisor into a power of 2 shift */
+	while (divisor) {
+		clock_div++;
+		divisor = divisor >> 1;
+	}
+
+	/*
+	 * Clock divider for QLM JTAG operations.  eclk is divided by
+	 * 2^(CLK_DIV + 2)
+	 */
+	jtgc.u64 = 0;
+	jtgc.s.clk_div = clock_div;
+	jtgc.s.mux_sel = 0;
+	if (OCTEON_IS_MODEL(OCTEON_CN52XX))
+		jtgc.s.bypass = 0x3;
+	else
+		jtgc.s.bypass = 0xf;
+	cvmx_write_csr(CVMX_CIU_QLM_JTGC, jtgc.u64);
+	cvmx_read_csr(CVMX_CIU_QLM_JTGC);
+}
+
+/**
+ * Write up to 32bits into the QLM jtag chain. Bits are shifted
+ * into the MSB and out the LSB, so you should shift in the low
+ * order bits followed by the high order bits. The JTAG chain is
+ * 4 * 268 bits long, or 1072.
+ *
+ * @qlm:    QLM to shift value into
+ * @bits:   Number of bits to shift in (1-32).
+ * @data:   Data to shift in. Bit 0 enters the chain first, followed by
+ *		 bit 1, etc.
+ *
+ * Returns The low order bits of the JTAG chain that shifted out of the
+ *	   circle.
+ */
+uint32_t cvmx_helper_qlm_jtag_shift(int qlm, int bits, uint32_t data)
+{
+	union cvmx_ciu_qlm_jtgd jtgd;
+	jtgd.u64 = 0;
+	jtgd.s.shift = 1;
+	jtgd.s.shft_cnt = bits - 1;
+	jtgd.s.shft_reg = data;
+	if (!OCTEON_IS_MODEL(OCTEON_CN56XX_PASS1_X))
+		jtgd.s.select = 1 << qlm;
+	cvmx_write_csr(CVMX_CIU_QLM_JTGD, jtgd.u64);
+	do {
+		jtgd.u64 = cvmx_read_csr(CVMX_CIU_QLM_JTGD);
+	} while (jtgd.s.shift);
+	return jtgd.s.shft_reg >> (32 - bits);
+}
+
+/**
+ * Shift long sequences of zeros into the QLM JTAG chain. It is
+ * common to need to shift more than 32 bits of zeros into the
+ * chain. This function is a convience wrapper around
+ * cvmx_helper_qlm_jtag_shift() to shift more than 32 bits of
+ * zeros at a time.
+ *
+ * @qlm:    QLM to shift zeros into
+ * @bits:
+ */
+void cvmx_helper_qlm_jtag_shift_zeros(int qlm, int bits)
+{
+	while (bits > 0) {
+		int n = bits;
+		if (n > 32)
+			n = 32;
+		cvmx_helper_qlm_jtag_shift(qlm, n, 0);
+		bits -= n;
+	}
+}
+
+/**
+ * Program the QLM JTAG chain into all lanes of the QLM. You must
+ * have already shifted in 268*4, or 1072 bits into the JTAG
+ * chain. Updating invalid values can possibly cause chip damage.
+ *
+ * @qlm:    QLM to program
+ */
+void cvmx_helper_qlm_jtag_update(int qlm)
+{
+	union cvmx_ciu_qlm_jtgd jtgd;
+
+	/* Update the new data */
+	jtgd.u64 = 0;
+	jtgd.s.update = 1;
+	if (!OCTEON_IS_MODEL(OCTEON_CN56XX_PASS1_X))
+		jtgd.s.select = 1 << qlm;
+	cvmx_write_csr(CVMX_CIU_QLM_JTGD, jtgd.u64);
+	do {
+		jtgd.u64 = cvmx_read_csr(CVMX_CIU_QLM_JTGD);
+	} while (jtgd.s.update);
+}
diff --git a/arch/mips/cavium-octeon/executive/cvmx-helper-loop.c b/arch/mips/cavium-octeon/executive/cvmx-helper-loop.c
new file mode 100644
index 000000000..bfbd46115
--- /dev/null
+++ b/arch/mips/cavium-octeon/executive/cvmx-helper-loop.c
@@ -0,0 +1,85 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ * Functions for LOOP initialization, configuration,
+ * and monitoring.
+ */
+#include <asm/octeon/octeon.h>
+
+#include <asm/octeon/cvmx-config.h>
+
+#include <asm/octeon/cvmx-helper.h>
+#include <asm/octeon/cvmx-pip-defs.h>
+
+/**
+ * Probe a LOOP interface and determine the number of ports
+ * connected to it. The LOOP interface should still be down
+ * after this call.
+ *
+ * @interface: Interface to probe
+ *
+ * Returns Number of ports on the interface. Zero to disable.
+ */
+int __cvmx_helper_loop_probe(int interface)
+{
+	union cvmx_ipd_sub_port_fcs ipd_sub_port_fcs;
+	int num_ports = 4;
+	int port;
+
+	/* We need to disable length checking so packet < 64 bytes and jumbo
+	   frames don't get errors */
+	for (port = 0; port < num_ports; port++) {
+		union cvmx_pip_prt_cfgx port_cfg;
+		int ipd_port = cvmx_helper_get_ipd_port(interface, port);
+		port_cfg.u64 = cvmx_read_csr(CVMX_PIP_PRT_CFGX(ipd_port));
+		port_cfg.s.maxerr_en = 0;
+		port_cfg.s.minerr_en = 0;
+		cvmx_write_csr(CVMX_PIP_PRT_CFGX(ipd_port), port_cfg.u64);
+	}
+
+	/* Disable FCS stripping for loopback ports */
+	ipd_sub_port_fcs.u64 = cvmx_read_csr(CVMX_IPD_SUB_PORT_FCS);
+	ipd_sub_port_fcs.s.port_bit2 = 0;
+	cvmx_write_csr(CVMX_IPD_SUB_PORT_FCS, ipd_sub_port_fcs.u64);
+	return num_ports;
+}
+
+/**
+ * Bringup and enable a LOOP interface. After this call packet
+ * I/O should be fully functional. This is called with IPD
+ * enabled but PKO disabled.
+ *
+ * @interface: Interface to bring up
+ *
+ * Returns Zero on success, negative on failure
+ */
+int __cvmx_helper_loop_enable(int interface)
+{
+	/* Do nothing. */
+	return 0;
+}
diff --git a/arch/mips/cavium-octeon/executive/cvmx-helper-npi.c b/arch/mips/cavium-octeon/executive/cvmx-helper-npi.c
new file mode 100644
index 000000000..cb210d2ef
--- /dev/null
+++ b/arch/mips/cavium-octeon/executive/cvmx-helper-npi.c
@@ -0,0 +1,101 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ * Functions for NPI initialization, configuration,
+ * and monitoring.
+ */
+#include <asm/octeon/octeon.h>
+
+#include <asm/octeon/cvmx-config.h>
+
+#include <asm/octeon/cvmx-helper.h>
+
+#include <asm/octeon/cvmx-pip-defs.h>
+
+/**
+ * Probe a NPI interface and determine the number of ports
+ * connected to it. The NPI interface should still be down
+ * after this call.
+ *
+ * @interface: Interface to probe
+ *
+ * Returns Number of ports on the interface. Zero to disable.
+ */
+int __cvmx_helper_npi_probe(int interface)
+{
+#if CVMX_PKO_QUEUES_PER_PORT_PCI > 0
+	if (OCTEON_IS_MODEL(OCTEON_CN38XX) || OCTEON_IS_MODEL(OCTEON_CN58XX))
+		return 4;
+	else if (OCTEON_IS_MODEL(OCTEON_CN56XX)
+		 && !OCTEON_IS_MODEL(OCTEON_CN56XX_PASS1_X))
+		/* The packet engines didn't exist before pass 2 */
+		return 4;
+	else if (OCTEON_IS_MODEL(OCTEON_CN52XX)
+		 && !OCTEON_IS_MODEL(OCTEON_CN52XX_PASS1_X))
+		/* The packet engines didn't exist before pass 2 */
+		return 4;
+#endif
+	return 0;
+}
+
+/**
+ * Bringup and enable a NPI interface. After this call packet
+ * I/O should be fully functional. This is called with IPD
+ * enabled but PKO disabled.
+ *
+ * @interface: Interface to bring up
+ *
+ * Returns Zero on success, negative on failure
+ */
+int __cvmx_helper_npi_enable(int interface)
+{
+	/*
+	 * On CN50XX, CN52XX, and CN56XX we need to disable length
+	 * checking so packet < 64 bytes and jumbo frames don't get
+	 * errors.
+	 */
+	if (!OCTEON_IS_MODEL(OCTEON_CN3XXX) &&
+	    !OCTEON_IS_MODEL(OCTEON_CN58XX)) {
+		int num_ports = cvmx_helper_ports_on_interface(interface);
+		int port;
+		for (port = 0; port < num_ports; port++) {
+			union cvmx_pip_prt_cfgx port_cfg;
+			int ipd_port =
+			    cvmx_helper_get_ipd_port(interface, port);
+			port_cfg.u64 =
+			    cvmx_read_csr(CVMX_PIP_PRT_CFGX(ipd_port));
+			port_cfg.s.maxerr_en = 0;
+			port_cfg.s.minerr_en = 0;
+			cvmx_write_csr(CVMX_PIP_PRT_CFGX(ipd_port),
+				       port_cfg.u64);
+		}
+	}
+
+	/* Enables are controlled by the remote host, so nothing to do here */
+	return 0;
+}
diff --git a/arch/mips/cavium-octeon/executive/cvmx-helper-rgmii.c b/arch/mips/cavium-octeon/executive/cvmx-helper-rgmii.c
new file mode 100644
index 000000000..a8c3be4eb
--- /dev/null
+++ b/arch/mips/cavium-octeon/executive/cvmx-helper-rgmii.c
@@ -0,0 +1,451 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (C) 2003-2018 Cavium, Inc.
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ * Functions for RGMII/GMII/MII initialization, configuration,
+ * and monitoring.
+ */
+#include <asm/octeon/octeon.h>
+
+#include <asm/octeon/cvmx-config.h>
+
+#include <asm/octeon/cvmx-pko.h>
+#include <asm/octeon/cvmx-helper.h>
+#include <asm/octeon/cvmx-helper-board.h>
+
+#include <asm/octeon/cvmx-npi-defs.h>
+#include <asm/octeon/cvmx-gmxx-defs.h>
+#include <asm/octeon/cvmx-asxx-defs.h>
+#include <asm/octeon/cvmx-dbg-defs.h>
+
+/*
+ * Probe RGMII ports and determine the number present
+ *
+ * @interface: Interface to probe
+ *
+ * Returns Number of RGMII/GMII/MII ports (0-4).
+ */
+int __cvmx_helper_rgmii_probe(int interface)
+{
+	int num_ports = 0;
+	union cvmx_gmxx_inf_mode mode;
+	mode.u64 = cvmx_read_csr(CVMX_GMXX_INF_MODE(interface));
+
+	if (mode.s.type) {
+		if (OCTEON_IS_MODEL(OCTEON_CN38XX)
+		    || OCTEON_IS_MODEL(OCTEON_CN58XX)) {
+			cvmx_dprintf("ERROR: RGMII initialize called in "
+				     "SPI interface\n");
+		} else if (OCTEON_IS_MODEL(OCTEON_CN31XX)
+			   || OCTEON_IS_MODEL(OCTEON_CN30XX)
+			   || OCTEON_IS_MODEL(OCTEON_CN50XX)) {
+			/*
+			 * On these chips "type" says we're in
+			 * GMII/MII mode. This limits us to 2 ports
+			 */
+			num_ports = 2;
+		} else {
+			cvmx_dprintf("ERROR: Unsupported Octeon model in %s\n",
+				     __func__);
+		}
+	} else {
+		if (OCTEON_IS_MODEL(OCTEON_CN38XX)
+		    || OCTEON_IS_MODEL(OCTEON_CN58XX)) {
+			num_ports = 4;
+		} else if (OCTEON_IS_MODEL(OCTEON_CN31XX)
+			   || OCTEON_IS_MODEL(OCTEON_CN30XX)
+			   || OCTEON_IS_MODEL(OCTEON_CN50XX)) {
+			num_ports = 3;
+		} else {
+			cvmx_dprintf("ERROR: Unsupported Octeon model in %s\n",
+				     __func__);
+		}
+	}
+	return num_ports;
+}
+
+/*
+ * Put an RGMII interface in loopback mode. Internal packets sent
+ * out will be received back again on the same port. Externally
+ * received packets will echo back out.
+ *
+ * @port:   IPD port number to loop.
+ */
+void cvmx_helper_rgmii_internal_loopback(int port)
+{
+	int interface = (port >> 4) & 1;
+	int index = port & 0xf;
+	uint64_t tmp;
+
+	union cvmx_gmxx_prtx_cfg gmx_cfg;
+	gmx_cfg.u64 = 0;
+	gmx_cfg.s.duplex = 1;
+	gmx_cfg.s.slottime = 1;
+	gmx_cfg.s.speed = 1;
+	cvmx_write_csr(CVMX_GMXX_TXX_CLK(index, interface), 1);
+	cvmx_write_csr(CVMX_GMXX_TXX_SLOT(index, interface), 0x200);
+	cvmx_write_csr(CVMX_GMXX_TXX_BURST(index, interface), 0x2000);
+	cvmx_write_csr(CVMX_GMXX_PRTX_CFG(index, interface), gmx_cfg.u64);
+	tmp = cvmx_read_csr(CVMX_ASXX_PRT_LOOP(interface));
+	cvmx_write_csr(CVMX_ASXX_PRT_LOOP(interface), (1 << index) | tmp);
+	tmp = cvmx_read_csr(CVMX_ASXX_TX_PRT_EN(interface));
+	cvmx_write_csr(CVMX_ASXX_TX_PRT_EN(interface), (1 << index) | tmp);
+	tmp = cvmx_read_csr(CVMX_ASXX_RX_PRT_EN(interface));
+	cvmx_write_csr(CVMX_ASXX_RX_PRT_EN(interface), (1 << index) | tmp);
+	gmx_cfg.s.en = 1;
+	cvmx_write_csr(CVMX_GMXX_PRTX_CFG(index, interface), gmx_cfg.u64);
+}
+
+/*
+ * Workaround ASX setup errata with CN38XX pass1
+ *
+ * @interface: Interface to setup
+ * @port:      Port to setup (0..3)
+ * @cpu_clock_hz:
+ *		    Chip frequency in Hertz
+ *
+ * Returns Zero on success, negative on failure
+ */
+static int __cvmx_helper_errata_asx_pass1(int interface, int port,
+					  int cpu_clock_hz)
+{
+	/* Set hi water mark as per errata GMX-4 */
+	if (cpu_clock_hz >= 325000000 && cpu_clock_hz < 375000000)
+		cvmx_write_csr(CVMX_ASXX_TX_HI_WATERX(port, interface), 12);
+	else if (cpu_clock_hz >= 375000000 && cpu_clock_hz < 437000000)
+		cvmx_write_csr(CVMX_ASXX_TX_HI_WATERX(port, interface), 11);
+	else if (cpu_clock_hz >= 437000000 && cpu_clock_hz < 550000000)
+		cvmx_write_csr(CVMX_ASXX_TX_HI_WATERX(port, interface), 10);
+	else if (cpu_clock_hz >= 550000000 && cpu_clock_hz < 687000000)
+		cvmx_write_csr(CVMX_ASXX_TX_HI_WATERX(port, interface), 9);
+	else
+		cvmx_dprintf("Illegal clock frequency (%d). "
+			"CVMX_ASXX_TX_HI_WATERX not set\n", cpu_clock_hz);
+	return 0;
+}
+
+/*
+ * Configure all of the ASX, GMX, and PKO registers required
+ * to get RGMII to function on the supplied interface.
+ *
+ * @interface: PKO Interface to configure (0 or 1)
+ *
+ * Returns Zero on success
+ */
+int __cvmx_helper_rgmii_enable(int interface)
+{
+	int num_ports = cvmx_helper_ports_on_interface(interface);
+	int port;
+	struct cvmx_sysinfo *sys_info_ptr = cvmx_sysinfo_get();
+	union cvmx_gmxx_inf_mode mode;
+	union cvmx_asxx_tx_prt_en asx_tx;
+	union cvmx_asxx_rx_prt_en asx_rx;
+
+	mode.u64 = cvmx_read_csr(CVMX_GMXX_INF_MODE(interface));
+
+	if (mode.s.en == 0)
+		return -1;
+	if ((OCTEON_IS_MODEL(OCTEON_CN38XX) ||
+	     OCTEON_IS_MODEL(OCTEON_CN58XX)) && mode.s.type == 1)
+		/* Ignore SPI interfaces */
+		return -1;
+
+	/* Configure the ASX registers needed to use the RGMII ports */
+	asx_tx.u64 = 0;
+	asx_tx.s.prt_en = cvmx_build_mask(num_ports);
+	cvmx_write_csr(CVMX_ASXX_TX_PRT_EN(interface), asx_tx.u64);
+
+	asx_rx.u64 = 0;
+	asx_rx.s.prt_en = cvmx_build_mask(num_ports);
+	cvmx_write_csr(CVMX_ASXX_RX_PRT_EN(interface), asx_rx.u64);
+
+	/* Configure the GMX registers needed to use the RGMII ports */
+	for (port = 0; port < num_ports; port++) {
+		/* Setting of CVMX_GMXX_TXX_THRESH has been moved to
+		   __cvmx_helper_setup_gmx() */
+
+		if (cvmx_octeon_is_pass1())
+			__cvmx_helper_errata_asx_pass1(interface, port,
+						       sys_info_ptr->
+						       cpu_clock_hz);
+		else {
+			/*
+			 * Configure more flexible RGMII preamble
+			 * checking. Pass 1 doesn't support this
+			 * feature.
+			 */
+			union cvmx_gmxx_rxx_frm_ctl frm_ctl;
+			frm_ctl.u64 =
+			    cvmx_read_csr(CVMX_GMXX_RXX_FRM_CTL
+					  (port, interface));
+			/* New field, so must be compile time */
+			frm_ctl.s.pre_free = 1;
+			cvmx_write_csr(CVMX_GMXX_RXX_FRM_CTL(port, interface),
+				       frm_ctl.u64);
+		}
+
+		/*
+		 * Each pause frame transmitted will ask for about 10M
+		 * bit times before resume.  If buffer space comes
+		 * available before that time has expired, an XON
+		 * pause frame (0 time) will be transmitted to restart
+		 * the flow.
+		 */
+		cvmx_write_csr(CVMX_GMXX_TXX_PAUSE_PKT_TIME(port, interface),
+			       20000);
+		cvmx_write_csr(CVMX_GMXX_TXX_PAUSE_PKT_INTERVAL
+			       (port, interface), 19000);
+
+		if (OCTEON_IS_MODEL(OCTEON_CN50XX)) {
+			cvmx_write_csr(CVMX_ASXX_TX_CLK_SETX(port, interface),
+				       16);
+			cvmx_write_csr(CVMX_ASXX_RX_CLK_SETX(port, interface),
+				       16);
+		} else {
+			cvmx_write_csr(CVMX_ASXX_TX_CLK_SETX(port, interface),
+				       24);
+			cvmx_write_csr(CVMX_ASXX_RX_CLK_SETX(port, interface),
+				       24);
+		}
+	}
+
+	__cvmx_helper_setup_gmx(interface, num_ports);
+
+	/* enable the ports now */
+	for (port = 0; port < num_ports; port++) {
+		union cvmx_gmxx_prtx_cfg gmx_cfg;
+
+		gmx_cfg.u64 =
+		    cvmx_read_csr(CVMX_GMXX_PRTX_CFG(port, interface));
+		gmx_cfg.s.en = 1;
+		cvmx_write_csr(CVMX_GMXX_PRTX_CFG(port, interface),
+			       gmx_cfg.u64);
+	}
+	__cvmx_interrupt_asxx_enable(interface);
+	__cvmx_interrupt_gmxx_enable(interface);
+
+	return 0;
+}
+
+/*
+ * Return the link state of an IPD/PKO port as returned by
+ * auto negotiation. The result of this function may not match
+ * Octeon's link config if auto negotiation has changed since
+ * the last call to cvmx_helper_link_set().
+ *
+ * @ipd_port: IPD/PKO port to query
+ *
+ * Returns Link state
+ */
+union cvmx_helper_link_info __cvmx_helper_rgmii_link_get(int ipd_port)
+{
+	int interface = cvmx_helper_get_interface_num(ipd_port);
+	int index = cvmx_helper_get_interface_index_num(ipd_port);
+	union cvmx_asxx_prt_loop asxx_prt_loop;
+
+	asxx_prt_loop.u64 = cvmx_read_csr(CVMX_ASXX_PRT_LOOP(interface));
+	if (asxx_prt_loop.s.int_loop & (1 << index)) {
+		/* Force 1Gbps full duplex on internal loopback */
+		union cvmx_helper_link_info result;
+		result.u64 = 0;
+		result.s.full_duplex = 1;
+		result.s.link_up = 1;
+		result.s.speed = 1000;
+		return result;
+	} else
+		return __cvmx_helper_board_link_get(ipd_port);
+}
+
+/*
+ * Configure an IPD/PKO port for the specified link state. This
+ * function does not influence auto negotiation at the PHY level.
+ * The passed link state must always match the link state returned
+ * by cvmx_helper_link_get().
+ *
+ * @ipd_port:  IPD/PKO port to configure
+ * @link_info: The new link state
+ *
+ * Returns Zero on success, negative on failure
+ */
+int __cvmx_helper_rgmii_link_set(int ipd_port,
+				 union cvmx_helper_link_info link_info)
+{
+	int result = 0;
+	int interface = cvmx_helper_get_interface_num(ipd_port);
+	int index = cvmx_helper_get_interface_index_num(ipd_port);
+	union cvmx_gmxx_prtx_cfg original_gmx_cfg;
+	union cvmx_gmxx_prtx_cfg new_gmx_cfg;
+	union cvmx_pko_mem_queue_qos pko_mem_queue_qos;
+	union cvmx_pko_mem_queue_qos pko_mem_queue_qos_save[16];
+	union cvmx_gmxx_tx_ovr_bp gmx_tx_ovr_bp;
+	union cvmx_gmxx_tx_ovr_bp gmx_tx_ovr_bp_save;
+	int i;
+
+	/* Ignore speed sets in the simulator */
+	if (cvmx_sysinfo_get()->board_type == CVMX_BOARD_TYPE_SIM)
+		return 0;
+
+	/* Read the current settings so we know the current enable state */
+	original_gmx_cfg.u64 =
+	    cvmx_read_csr(CVMX_GMXX_PRTX_CFG(index, interface));
+	new_gmx_cfg = original_gmx_cfg;
+
+	/* Disable the lowest level RX */
+	cvmx_write_csr(CVMX_ASXX_RX_PRT_EN(interface),
+		       cvmx_read_csr(CVMX_ASXX_RX_PRT_EN(interface)) &
+				     ~(1 << index));
+
+	memset(pko_mem_queue_qos_save, 0, sizeof(pko_mem_queue_qos_save));
+	/* Disable all queues so that TX should become idle */
+	for (i = 0; i < cvmx_pko_get_num_queues(ipd_port); i++) {
+		int queue = cvmx_pko_get_base_queue(ipd_port) + i;
+		cvmx_write_csr(CVMX_PKO_REG_READ_IDX, queue);
+		pko_mem_queue_qos.u64 = cvmx_read_csr(CVMX_PKO_MEM_QUEUE_QOS);
+		pko_mem_queue_qos.s.pid = ipd_port;
+		pko_mem_queue_qos.s.qid = queue;
+		pko_mem_queue_qos_save[i] = pko_mem_queue_qos;
+		pko_mem_queue_qos.s.qos_mask = 0;
+		cvmx_write_csr(CVMX_PKO_MEM_QUEUE_QOS, pko_mem_queue_qos.u64);
+	}
+
+	/* Disable backpressure */
+	gmx_tx_ovr_bp.u64 = cvmx_read_csr(CVMX_GMXX_TX_OVR_BP(interface));
+	gmx_tx_ovr_bp_save = gmx_tx_ovr_bp;
+	gmx_tx_ovr_bp.s.bp &= ~(1 << index);
+	gmx_tx_ovr_bp.s.en |= 1 << index;
+	cvmx_write_csr(CVMX_GMXX_TX_OVR_BP(interface), gmx_tx_ovr_bp.u64);
+	cvmx_read_csr(CVMX_GMXX_TX_OVR_BP(interface));
+
+	/*
+	 * Poll the GMX state machine waiting for it to become
+	 * idle. Preferably we should only change speed when it is
+	 * idle. If it doesn't become idle we will still do the speed
+	 * change, but there is a slight chance that GMX will
+	 * lockup.
+	 */
+	cvmx_write_csr(CVMX_NPI_DBG_SELECT,
+		       interface * 0x800 + index * 0x100 + 0x880);
+	CVMX_WAIT_FOR_FIELD64(CVMX_DBG_DATA, union cvmx_dbg_data, data & 7,
+			==, 0, 10000);
+	CVMX_WAIT_FOR_FIELD64(CVMX_DBG_DATA, union cvmx_dbg_data, data & 0xf,
+			==, 0, 10000);
+
+	/* Disable the port before we make any changes */
+	new_gmx_cfg.s.en = 0;
+	cvmx_write_csr(CVMX_GMXX_PRTX_CFG(index, interface), new_gmx_cfg.u64);
+	cvmx_read_csr(CVMX_GMXX_PRTX_CFG(index, interface));
+
+	/* Set full/half duplex */
+	if (cvmx_octeon_is_pass1())
+		/* Half duplex is broken for 38XX Pass 1 */
+		new_gmx_cfg.s.duplex = 1;
+	else if (!link_info.s.link_up)
+		/* Force full duplex on down links */
+		new_gmx_cfg.s.duplex = 1;
+	else
+		new_gmx_cfg.s.duplex = link_info.s.full_duplex;
+
+	/* Set the link speed. Anything unknown is set to 1Gbps */
+	if (link_info.s.speed == 10) {
+		new_gmx_cfg.s.slottime = 0;
+		new_gmx_cfg.s.speed = 0;
+	} else if (link_info.s.speed == 100) {
+		new_gmx_cfg.s.slottime = 0;
+		new_gmx_cfg.s.speed = 0;
+	} else {
+		new_gmx_cfg.s.slottime = 1;
+		new_gmx_cfg.s.speed = 1;
+	}
+
+	/* Adjust the clocks */
+	if (link_info.s.speed == 10) {
+		cvmx_write_csr(CVMX_GMXX_TXX_CLK(index, interface), 50);
+		cvmx_write_csr(CVMX_GMXX_TXX_SLOT(index, interface), 0x40);
+		cvmx_write_csr(CVMX_GMXX_TXX_BURST(index, interface), 0);
+	} else if (link_info.s.speed == 100) {
+		cvmx_write_csr(CVMX_GMXX_TXX_CLK(index, interface), 5);
+		cvmx_write_csr(CVMX_GMXX_TXX_SLOT(index, interface), 0x40);
+		cvmx_write_csr(CVMX_GMXX_TXX_BURST(index, interface), 0);
+	} else {
+		cvmx_write_csr(CVMX_GMXX_TXX_CLK(index, interface), 1);
+		cvmx_write_csr(CVMX_GMXX_TXX_SLOT(index, interface), 0x200);
+		cvmx_write_csr(CVMX_GMXX_TXX_BURST(index, interface), 0x2000);
+	}
+
+	if (OCTEON_IS_MODEL(OCTEON_CN30XX) || OCTEON_IS_MODEL(OCTEON_CN50XX)) {
+		if ((link_info.s.speed == 10) || (link_info.s.speed == 100)) {
+			union cvmx_gmxx_inf_mode mode;
+			mode.u64 = cvmx_read_csr(CVMX_GMXX_INF_MODE(interface));
+
+	/*
+	 * Port	 .en  .type  .p0mii  Configuration
+	 * ----	 ---  -----  ------  -----------------------------------------
+	 *  X	   0	 X	X    All links are disabled.
+	 *  0	   1	 X	0    Port 0 is RGMII
+	 *  0	   1	 X	1    Port 0 is MII
+	 *  1	   1	 0	X    Ports 1 and 2 are configured as RGMII ports.
+	 *  1	   1	 1	X    Port 1: GMII/MII; Port 2: disabled. GMII or
+	 *			     MII port is selected by GMX_PRT1_CFG[SPEED].
+	 */
+
+			/* In MII mode, CLK_CNT = 1. */
+			if (((index == 0) && (mode.s.p0mii == 1))
+			    || ((index != 0) && (mode.s.type == 1))) {
+				cvmx_write_csr(CVMX_GMXX_TXX_CLK
+					       (index, interface), 1);
+			}
+		}
+	}
+
+	/* Do a read to make sure all setup stuff is complete */
+	cvmx_read_csr(CVMX_GMXX_PRTX_CFG(index, interface));
+
+	/* Save the new GMX setting without enabling the port */
+	cvmx_write_csr(CVMX_GMXX_PRTX_CFG(index, interface), new_gmx_cfg.u64);
+
+	/* Enable the lowest level RX */
+	cvmx_write_csr(CVMX_ASXX_RX_PRT_EN(interface),
+		       cvmx_read_csr(CVMX_ASXX_RX_PRT_EN(interface)) | (1 <<
+									index));
+
+	/* Re-enable the TX path */
+	for (i = 0; i < cvmx_pko_get_num_queues(ipd_port); i++) {
+		int queue = cvmx_pko_get_base_queue(ipd_port) + i;
+		cvmx_write_csr(CVMX_PKO_REG_READ_IDX, queue);
+		cvmx_write_csr(CVMX_PKO_MEM_QUEUE_QOS,
+			       pko_mem_queue_qos_save[i].u64);
+	}
+
+	/* Restore backpressure */
+	cvmx_write_csr(CVMX_GMXX_TX_OVR_BP(interface), gmx_tx_ovr_bp_save.u64);
+
+	/* Restore the GMX enable state. Port config is complete */
+	new_gmx_cfg.s.en = original_gmx_cfg.s.en;
+	cvmx_write_csr(CVMX_GMXX_PRTX_CFG(index, interface), new_gmx_cfg.u64);
+
+	return result;
+}
diff --git a/arch/mips/cavium-octeon/executive/cvmx-helper-sgmii.c b/arch/mips/cavium-octeon/executive/cvmx-helper-sgmii.c
new file mode 100644
index 000000000..e07d8f15e
--- /dev/null
+++ b/arch/mips/cavium-octeon/executive/cvmx-helper-sgmii.c
@@ -0,0 +1,515 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (C) 2003-2018 Cavium, Inc.
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ * Functions for SGMII initialization, configuration,
+ * and monitoring.
+ */
+
+#include <asm/octeon/octeon.h>
+
+#include <asm/octeon/cvmx-config.h>
+
+#include <asm/octeon/cvmx-helper.h>
+#include <asm/octeon/cvmx-helper-board.h>
+
+#include <asm/octeon/cvmx-gmxx-defs.h>
+#include <asm/octeon/cvmx-pcsx-defs.h>
+#include <asm/octeon/cvmx-pcsxx-defs.h>
+
+/**
+ * Perform initialization required only once for an SGMII port.
+ *
+ * @interface: Interface to init
+ * @index:     Index of prot on the interface
+ *
+ * Returns Zero on success, negative on failure
+ */
+static int __cvmx_helper_sgmii_hardware_init_one_time(int interface, int index)
+{
+	const uint64_t clock_mhz = cvmx_sysinfo_get()->cpu_clock_hz / 1000000;
+	union cvmx_pcsx_miscx_ctl_reg pcs_misc_ctl_reg;
+	union cvmx_pcsx_linkx_timer_count_reg pcsx_linkx_timer_count_reg;
+	union cvmx_gmxx_prtx_cfg gmxx_prtx_cfg;
+
+	/* Disable GMX */
+	gmxx_prtx_cfg.u64 = cvmx_read_csr(CVMX_GMXX_PRTX_CFG(index, interface));
+	gmxx_prtx_cfg.s.en = 0;
+	cvmx_write_csr(CVMX_GMXX_PRTX_CFG(index, interface), gmxx_prtx_cfg.u64);
+
+	/*
+	 * Write PCS*_LINK*_TIMER_COUNT_REG[COUNT] with the
+	 * appropriate value. 1000BASE-X specifies a 10ms
+	 * interval. SGMII specifies a 1.6ms interval.
+	 */
+	pcs_misc_ctl_reg.u64 =
+	    cvmx_read_csr(CVMX_PCSX_MISCX_CTL_REG(index, interface));
+	pcsx_linkx_timer_count_reg.u64 =
+	    cvmx_read_csr(CVMX_PCSX_LINKX_TIMER_COUNT_REG(index, interface));
+	if (pcs_misc_ctl_reg.s.mode) {
+		/* 1000BASE-X */
+		pcsx_linkx_timer_count_reg.s.count =
+		    (10000ull * clock_mhz) >> 10;
+	} else {
+		/* SGMII */
+		pcsx_linkx_timer_count_reg.s.count =
+		    (1600ull * clock_mhz) >> 10;
+	}
+	cvmx_write_csr(CVMX_PCSX_LINKX_TIMER_COUNT_REG(index, interface),
+		       pcsx_linkx_timer_count_reg.u64);
+
+	/*
+	 * Write the advertisement register to be used as the
+	 * tx_Config_Reg<D15:D0> of the autonegotiation.  In
+	 * 1000BASE-X mode, tx_Config_Reg<D15:D0> is PCS*_AN*_ADV_REG.
+	 * In SGMII PHY mode, tx_Config_Reg<D15:D0> is
+	 * PCS*_SGM*_AN_ADV_REG.  In SGMII MAC mode,
+	 * tx_Config_Reg<D15:D0> is the fixed value 0x4001, so this
+	 * step can be skipped.
+	 */
+	if (pcs_misc_ctl_reg.s.mode) {
+		/* 1000BASE-X */
+		union cvmx_pcsx_anx_adv_reg pcsx_anx_adv_reg;
+		pcsx_anx_adv_reg.u64 =
+		    cvmx_read_csr(CVMX_PCSX_ANX_ADV_REG(index, interface));
+		pcsx_anx_adv_reg.s.rem_flt = 0;
+		pcsx_anx_adv_reg.s.pause = 3;
+		pcsx_anx_adv_reg.s.hfd = 1;
+		pcsx_anx_adv_reg.s.fd = 1;
+		cvmx_write_csr(CVMX_PCSX_ANX_ADV_REG(index, interface),
+			       pcsx_anx_adv_reg.u64);
+	} else {
+		union cvmx_pcsx_miscx_ctl_reg pcsx_miscx_ctl_reg;
+		pcsx_miscx_ctl_reg.u64 =
+		    cvmx_read_csr(CVMX_PCSX_MISCX_CTL_REG(index, interface));
+		if (pcsx_miscx_ctl_reg.s.mac_phy) {
+			/* PHY Mode */
+			union cvmx_pcsx_sgmx_an_adv_reg pcsx_sgmx_an_adv_reg;
+			pcsx_sgmx_an_adv_reg.u64 =
+			    cvmx_read_csr(CVMX_PCSX_SGMX_AN_ADV_REG
+					  (index, interface));
+			pcsx_sgmx_an_adv_reg.s.link = 1;
+			pcsx_sgmx_an_adv_reg.s.dup = 1;
+			pcsx_sgmx_an_adv_reg.s.speed = 2;
+			cvmx_write_csr(CVMX_PCSX_SGMX_AN_ADV_REG
+				       (index, interface),
+				       pcsx_sgmx_an_adv_reg.u64);
+		} else {
+			/* MAC Mode - Nothing to do */
+		}
+	}
+	return 0;
+}
+
+/**
+ * Initialize the SERTES link for the first time or after a loss
+ * of link.
+ *
+ * @interface: Interface to init
+ * @index:     Index of prot on the interface
+ *
+ * Returns Zero on success, negative on failure
+ */
+static int __cvmx_helper_sgmii_hardware_init_link(int interface, int index)
+{
+	union cvmx_pcsx_mrx_control_reg control_reg;
+
+	/*
+	 * Take PCS through a reset sequence.
+	 * PCS*_MR*_CONTROL_REG[PWR_DN] should be cleared to zero.
+	 * Write PCS*_MR*_CONTROL_REG[RESET]=1 (while not changing the
+	 * value of the other PCS*_MR*_CONTROL_REG bits).  Read
+	 * PCS*_MR*_CONTROL_REG[RESET] until it changes value to
+	 * zero.
+	 */
+	control_reg.u64 =
+	    cvmx_read_csr(CVMX_PCSX_MRX_CONTROL_REG(index, interface));
+	if (cvmx_sysinfo_get()->board_type != CVMX_BOARD_TYPE_SIM) {
+		control_reg.s.reset = 1;
+		cvmx_write_csr(CVMX_PCSX_MRX_CONTROL_REG(index, interface),
+			       control_reg.u64);
+		if (CVMX_WAIT_FOR_FIELD64
+		    (CVMX_PCSX_MRX_CONTROL_REG(index, interface),
+		     union cvmx_pcsx_mrx_control_reg, reset, ==, 0, 10000)) {
+			cvmx_dprintf("SGMII%d: Timeout waiting for port %d "
+				     "to finish reset\n",
+			     interface, index);
+			return -1;
+		}
+	}
+
+	/*
+	 * Write PCS*_MR*_CONTROL_REG[RST_AN]=1 to ensure a fresh
+	 * sgmii negotiation starts.
+	 */
+	control_reg.s.rst_an = 1;
+	control_reg.s.an_en = 1;
+	control_reg.s.pwr_dn = 0;
+	cvmx_write_csr(CVMX_PCSX_MRX_CONTROL_REG(index, interface),
+		       control_reg.u64);
+
+	/*
+	 * Wait for PCS*_MR*_STATUS_REG[AN_CPT] to be set, indicating
+	 * that sgmii autonegotiation is complete. In MAC mode this
+	 * isn't an ethernet link, but a link between Octeon and the
+	 * PHY.
+	 */
+	if ((cvmx_sysinfo_get()->board_type != CVMX_BOARD_TYPE_SIM) &&
+	    CVMX_WAIT_FOR_FIELD64(CVMX_PCSX_MRX_STATUS_REG(index, interface),
+				  union cvmx_pcsx_mrx_status_reg, an_cpt, ==, 1,
+				  10000)) {
+		/* cvmx_dprintf("SGMII%d: Port %d link timeout\n", interface, index); */
+		return -1;
+	}
+	return 0;
+}
+
+/**
+ * Configure an SGMII link to the specified speed after the SERTES
+ * link is up.
+ *
+ * @interface: Interface to init
+ * @index:     Index of prot on the interface
+ * @link_info: Link state to configure
+ *
+ * Returns Zero on success, negative on failure
+ */
+static int __cvmx_helper_sgmii_hardware_init_link_speed(int interface,
+							int index,
+							union cvmx_helper_link_info
+							link_info)
+{
+	int is_enabled;
+	union cvmx_gmxx_prtx_cfg gmxx_prtx_cfg;
+	union cvmx_pcsx_miscx_ctl_reg pcsx_miscx_ctl_reg;
+
+	/* Disable GMX before we make any changes. Remember the enable state */
+	gmxx_prtx_cfg.u64 = cvmx_read_csr(CVMX_GMXX_PRTX_CFG(index, interface));
+	is_enabled = gmxx_prtx_cfg.s.en;
+	gmxx_prtx_cfg.s.en = 0;
+	cvmx_write_csr(CVMX_GMXX_PRTX_CFG(index, interface), gmxx_prtx_cfg.u64);
+
+	/* Wait for GMX to be idle */
+	if (CVMX_WAIT_FOR_FIELD64
+	    (CVMX_GMXX_PRTX_CFG(index, interface), union cvmx_gmxx_prtx_cfg,
+	     rx_idle, ==, 1, 10000)
+	    || CVMX_WAIT_FOR_FIELD64(CVMX_GMXX_PRTX_CFG(index, interface),
+				     union cvmx_gmxx_prtx_cfg, tx_idle, ==, 1,
+				     10000)) {
+		cvmx_dprintf
+		    ("SGMII%d: Timeout waiting for port %d to be idle\n",
+		     interface, index);
+		return -1;
+	}
+
+	/* Read GMX CFG again to make sure the disable completed */
+	gmxx_prtx_cfg.u64 = cvmx_read_csr(CVMX_GMXX_PRTX_CFG(index, interface));
+
+	/*
+	 * Get the misc control for PCS. We will need to set the
+	 * duplication amount.
+	 */
+	pcsx_miscx_ctl_reg.u64 =
+	    cvmx_read_csr(CVMX_PCSX_MISCX_CTL_REG(index, interface));
+
+	/*
+	 * Use GMXENO to force the link down if the status we get says
+	 * it should be down.
+	 */
+	pcsx_miscx_ctl_reg.s.gmxeno = !link_info.s.link_up;
+
+	/* Only change the duplex setting if the link is up */
+	if (link_info.s.link_up)
+		gmxx_prtx_cfg.s.duplex = link_info.s.full_duplex;
+
+	/* Do speed based setting for GMX */
+	switch (link_info.s.speed) {
+	case 10:
+		gmxx_prtx_cfg.s.speed = 0;
+		gmxx_prtx_cfg.s.speed_msb = 1;
+		gmxx_prtx_cfg.s.slottime = 0;
+		/* Setting from GMX-603 */
+		pcsx_miscx_ctl_reg.s.samp_pt = 25;
+		cvmx_write_csr(CVMX_GMXX_TXX_SLOT(index, interface), 64);
+		cvmx_write_csr(CVMX_GMXX_TXX_BURST(index, interface), 0);
+		break;
+	case 100:
+		gmxx_prtx_cfg.s.speed = 0;
+		gmxx_prtx_cfg.s.speed_msb = 0;
+		gmxx_prtx_cfg.s.slottime = 0;
+		pcsx_miscx_ctl_reg.s.samp_pt = 0x5;
+		cvmx_write_csr(CVMX_GMXX_TXX_SLOT(index, interface), 64);
+		cvmx_write_csr(CVMX_GMXX_TXX_BURST(index, interface), 0);
+		break;
+	case 1000:
+		gmxx_prtx_cfg.s.speed = 1;
+		gmxx_prtx_cfg.s.speed_msb = 0;
+		gmxx_prtx_cfg.s.slottime = 1;
+		pcsx_miscx_ctl_reg.s.samp_pt = 1;
+		cvmx_write_csr(CVMX_GMXX_TXX_SLOT(index, interface), 512);
+		cvmx_write_csr(CVMX_GMXX_TXX_BURST(index, interface), 8192);
+		break;
+	default:
+		break;
+	}
+
+	/* Write the new misc control for PCS */
+	cvmx_write_csr(CVMX_PCSX_MISCX_CTL_REG(index, interface),
+		       pcsx_miscx_ctl_reg.u64);
+
+	/* Write the new GMX settings with the port still disabled */
+	cvmx_write_csr(CVMX_GMXX_PRTX_CFG(index, interface), gmxx_prtx_cfg.u64);
+
+	/* Read GMX CFG again to make sure the config completed */
+	gmxx_prtx_cfg.u64 = cvmx_read_csr(CVMX_GMXX_PRTX_CFG(index, interface));
+
+	/* Restore the enabled / disabled state */
+	gmxx_prtx_cfg.s.en = is_enabled;
+	cvmx_write_csr(CVMX_GMXX_PRTX_CFG(index, interface), gmxx_prtx_cfg.u64);
+
+	return 0;
+}
+
+/**
+ * Bring up the SGMII interface to be ready for packet I/O but
+ * leave I/O disabled using the GMX override. This function
+ * follows the bringup documented in 10.6.3 of the manual.
+ *
+ * @interface: Interface to bringup
+ * @num_ports: Number of ports on the interface
+ *
+ * Returns Zero on success, negative on failure
+ */
+static int __cvmx_helper_sgmii_hardware_init(int interface, int num_ports)
+{
+	int index;
+
+	__cvmx_helper_setup_gmx(interface, num_ports);
+
+	for (index = 0; index < num_ports; index++) {
+		int ipd_port = cvmx_helper_get_ipd_port(interface, index);
+		__cvmx_helper_sgmii_hardware_init_one_time(interface, index);
+		/* Linux kernel driver will call ....link_set with the
+		 * proper link state. In the simulator there is no
+		 * link state polling and hence it is set from
+		 * here.
+		 */
+		if (cvmx_sysinfo_get()->board_type == CVMX_BOARD_TYPE_SIM)
+			__cvmx_helper_sgmii_link_set(ipd_port,
+				       __cvmx_helper_sgmii_link_get(ipd_port));
+	}
+
+	return 0;
+}
+
+int __cvmx_helper_sgmii_enumerate(int interface)
+{
+	return 4;
+}
+/**
+ * Probe a SGMII interface and determine the number of ports
+ * connected to it. The SGMII interface should still be down after
+ * this call.
+ *
+ * @interface: Interface to probe
+ *
+ * Returns Number of ports on the interface. Zero to disable.
+ */
+int __cvmx_helper_sgmii_probe(int interface)
+{
+	union cvmx_gmxx_inf_mode mode;
+
+	/*
+	 * Due to errata GMX-700 on CN56XXp1.x and CN52XXp1.x, the
+	 * interface needs to be enabled before IPD otherwise per port
+	 * backpressure may not work properly
+	 */
+	mode.u64 = cvmx_read_csr(CVMX_GMXX_INF_MODE(interface));
+	mode.s.en = 1;
+	cvmx_write_csr(CVMX_GMXX_INF_MODE(interface), mode.u64);
+	return __cvmx_helper_sgmii_enumerate(interface);
+}
+
+/**
+ * Bringup and enable a SGMII interface. After this call packet
+ * I/O should be fully functional. This is called with IPD
+ * enabled but PKO disabled.
+ *
+ * @interface: Interface to bring up
+ *
+ * Returns Zero on success, negative on failure
+ */
+int __cvmx_helper_sgmii_enable(int interface)
+{
+	int num_ports = cvmx_helper_ports_on_interface(interface);
+	int index;
+
+	__cvmx_helper_sgmii_hardware_init(interface, num_ports);
+
+	for (index = 0; index < num_ports; index++) {
+		union cvmx_gmxx_prtx_cfg gmxx_prtx_cfg;
+		gmxx_prtx_cfg.u64 =
+		    cvmx_read_csr(CVMX_GMXX_PRTX_CFG(index, interface));
+		gmxx_prtx_cfg.s.en = 1;
+		cvmx_write_csr(CVMX_GMXX_PRTX_CFG(index, interface),
+			       gmxx_prtx_cfg.u64);
+		__cvmx_interrupt_pcsx_intx_en_reg_enable(index, interface);
+	}
+	__cvmx_interrupt_pcsxx_int_en_reg_enable(interface);
+	__cvmx_interrupt_gmxx_enable(interface);
+	return 0;
+}
+
+/**
+ * Return the link state of an IPD/PKO port as returned by
+ * auto negotiation. The result of this function may not match
+ * Octeon's link config if auto negotiation has changed since
+ * the last call to cvmx_helper_link_set().
+ *
+ * @ipd_port: IPD/PKO port to query
+ *
+ * Returns Link state
+ */
+union cvmx_helper_link_info __cvmx_helper_sgmii_link_get(int ipd_port)
+{
+	union cvmx_helper_link_info result;
+	union cvmx_pcsx_miscx_ctl_reg pcs_misc_ctl_reg;
+	int interface = cvmx_helper_get_interface_num(ipd_port);
+	int index = cvmx_helper_get_interface_index_num(ipd_port);
+	union cvmx_pcsx_mrx_control_reg pcsx_mrx_control_reg;
+
+	result.u64 = 0;
+
+	if (cvmx_sysinfo_get()->board_type == CVMX_BOARD_TYPE_SIM) {
+		/* The simulator gives you a simulated 1Gbps full duplex link */
+		result.s.link_up = 1;
+		result.s.full_duplex = 1;
+		result.s.speed = 1000;
+		return result;
+	}
+
+	pcsx_mrx_control_reg.u64 =
+	    cvmx_read_csr(CVMX_PCSX_MRX_CONTROL_REG(index, interface));
+	if (pcsx_mrx_control_reg.s.loopbck1) {
+		/* Force 1Gbps full duplex link for internal loopback */
+		result.s.link_up = 1;
+		result.s.full_duplex = 1;
+		result.s.speed = 1000;
+		return result;
+	}
+
+	pcs_misc_ctl_reg.u64 =
+	    cvmx_read_csr(CVMX_PCSX_MISCX_CTL_REG(index, interface));
+	if (pcs_misc_ctl_reg.s.mode) {
+		/* 1000BASE-X */
+		/* FIXME */
+	} else {
+		union cvmx_pcsx_miscx_ctl_reg pcsx_miscx_ctl_reg;
+		pcsx_miscx_ctl_reg.u64 =
+		    cvmx_read_csr(CVMX_PCSX_MISCX_CTL_REG(index, interface));
+		if (pcsx_miscx_ctl_reg.s.mac_phy) {
+			/* PHY Mode */
+			union cvmx_pcsx_mrx_status_reg pcsx_mrx_status_reg;
+			union cvmx_pcsx_anx_results_reg pcsx_anx_results_reg;
+
+			/*
+			 * Don't bother continuing if the SERTES low
+			 * level link is down
+			 */
+			pcsx_mrx_status_reg.u64 =
+			    cvmx_read_csr(CVMX_PCSX_MRX_STATUS_REG
+					  (index, interface));
+			if (pcsx_mrx_status_reg.s.lnk_st == 0) {
+				if (__cvmx_helper_sgmii_hardware_init_link
+				    (interface, index) != 0)
+					return result;
+			}
+
+			/* Read the autoneg results */
+			pcsx_anx_results_reg.u64 =
+			    cvmx_read_csr(CVMX_PCSX_ANX_RESULTS_REG
+					  (index, interface));
+			if (pcsx_anx_results_reg.s.an_cpt) {
+				/*
+				 * Auto negotiation is complete. Set
+				 * status accordingly.
+				 */
+				result.s.full_duplex =
+				    pcsx_anx_results_reg.s.dup;
+				result.s.link_up =
+				    pcsx_anx_results_reg.s.link_ok;
+				switch (pcsx_anx_results_reg.s.spd) {
+				case 0:
+					result.s.speed = 10;
+					break;
+				case 1:
+					result.s.speed = 100;
+					break;
+				case 2:
+					result.s.speed = 1000;
+					break;
+				default:
+					result.s.speed = 0;
+					result.s.link_up = 0;
+					break;
+				}
+			} else {
+				/*
+				 * Auto negotiation isn't
+				 * complete. Return link down.
+				 */
+				result.s.speed = 0;
+				result.s.link_up = 0;
+			}
+		} else {	/* MAC Mode */
+
+			result = __cvmx_helper_board_link_get(ipd_port);
+		}
+	}
+	return result;
+}
+
+/**
+ * Configure an IPD/PKO port for the specified link state. This
+ * function does not influence auto negotiation at the PHY level.
+ * The passed link state must always match the link state returned
+ * by cvmx_helper_link_get().
+ *
+ * @ipd_port:  IPD/PKO port to configure
+ * @link_info: The new link state
+ *
+ * Returns Zero on success, negative on failure
+ */
+int __cvmx_helper_sgmii_link_set(int ipd_port,
+				 union cvmx_helper_link_info link_info)
+{
+	int interface = cvmx_helper_get_interface_num(ipd_port);
+	int index = cvmx_helper_get_interface_index_num(ipd_port);
+	__cvmx_helper_sgmii_hardware_init_link(interface, index);
+	return __cvmx_helper_sgmii_hardware_init_link_speed(interface, index,
+							    link_info);
+}
diff --git a/arch/mips/cavium-octeon/executive/cvmx-helper-spi.c b/arch/mips/cavium-octeon/executive/cvmx-helper-spi.c
new file mode 100644
index 000000000..525914e9b
--- /dev/null
+++ b/arch/mips/cavium-octeon/executive/cvmx-helper-spi.c
@@ -0,0 +1,202 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (C) 2003-2018 Cavium, Inc.
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ * Functions for SPI initialization, configuration,
+ * and monitoring.
+ */
+#include <asm/octeon/octeon.h>
+
+#include <asm/octeon/cvmx-config.h>
+#include <asm/octeon/cvmx-spi.h>
+#include <asm/octeon/cvmx-helper.h>
+
+#include <asm/octeon/cvmx-pip-defs.h>
+#include <asm/octeon/cvmx-pko-defs.h>
+#include <asm/octeon/cvmx-spxx-defs.h>
+#include <asm/octeon/cvmx-stxx-defs.h>
+
+/*
+ * CVMX_HELPER_SPI_TIMEOUT is used to determine how long the SPI
+ * initialization routines wait for SPI training. You can override the
+ * value using executive-config.h if necessary.
+ */
+#ifndef CVMX_HELPER_SPI_TIMEOUT
+#define CVMX_HELPER_SPI_TIMEOUT 10
+#endif
+
+int __cvmx_helper_spi_enumerate(int interface)
+{
+	if ((cvmx_sysinfo_get()->board_type != CVMX_BOARD_TYPE_SIM) &&
+	    cvmx_spi4000_is_present(interface)) {
+		return 10;
+	} else {
+		return 16;
+	}
+}
+
+/**
+ * Probe a SPI interface and determine the number of ports
+ * connected to it. The SPI interface should still be down after
+ * this call.
+ *
+ * @interface: Interface to probe
+ *
+ * Returns Number of ports on the interface. Zero to disable.
+ */
+int __cvmx_helper_spi_probe(int interface)
+{
+	int num_ports = 0;
+
+	if ((cvmx_sysinfo_get()->board_type != CVMX_BOARD_TYPE_SIM) &&
+	    cvmx_spi4000_is_present(interface)) {
+		num_ports = 10;
+	} else {
+		union cvmx_pko_reg_crc_enable enable;
+		num_ports = 16;
+		/*
+		 * Unlike the SPI4000, most SPI devices don't
+		 * automatically put on the L2 CRC. For everything
+		 * except for the SPI4000 have PKO append the L2 CRC
+		 * to the packet.
+		 */
+		enable.u64 = cvmx_read_csr(CVMX_PKO_REG_CRC_ENABLE);
+		enable.s.enable |= 0xffff << (interface * 16);
+		cvmx_write_csr(CVMX_PKO_REG_CRC_ENABLE, enable.u64);
+	}
+	__cvmx_helper_setup_gmx(interface, num_ports);
+	return num_ports;
+}
+
+/**
+ * Bringup and enable a SPI interface. After this call packet I/O
+ * should be fully functional. This is called with IPD enabled but
+ * PKO disabled.
+ *
+ * @interface: Interface to bring up
+ *
+ * Returns Zero on success, negative on failure
+ */
+int __cvmx_helper_spi_enable(int interface)
+{
+	/*
+	 * Normally the ethernet L2 CRC is checked and stripped in the
+	 * GMX block.  When you are using SPI, this isn' the case and
+	 * IPD needs to check the L2 CRC.
+	 */
+	int num_ports = cvmx_helper_ports_on_interface(interface);
+	int ipd_port;
+	for (ipd_port = interface * 16; ipd_port < interface * 16 + num_ports;
+	     ipd_port++) {
+		union cvmx_pip_prt_cfgx port_config;
+		port_config.u64 = cvmx_read_csr(CVMX_PIP_PRT_CFGX(ipd_port));
+		port_config.s.crc_en = 1;
+		cvmx_write_csr(CVMX_PIP_PRT_CFGX(ipd_port), port_config.u64);
+	}
+
+	if (cvmx_sysinfo_get()->board_type != CVMX_BOARD_TYPE_SIM) {
+		cvmx_spi_start_interface(interface, CVMX_SPI_MODE_DUPLEX,
+					 CVMX_HELPER_SPI_TIMEOUT, num_ports);
+		if (cvmx_spi4000_is_present(interface))
+			cvmx_spi4000_initialize(interface);
+	}
+	__cvmx_interrupt_spxx_int_msk_enable(interface);
+	__cvmx_interrupt_stxx_int_msk_enable(interface);
+	__cvmx_interrupt_gmxx_enable(interface);
+	return 0;
+}
+
+/**
+ * Return the link state of an IPD/PKO port as returned by
+ * auto negotiation. The result of this function may not match
+ * Octeon's link config if auto negotiation has changed since
+ * the last call to cvmx_helper_link_set().
+ *
+ * @ipd_port: IPD/PKO port to query
+ *
+ * Returns Link state
+ */
+union cvmx_helper_link_info __cvmx_helper_spi_link_get(int ipd_port)
+{
+	union cvmx_helper_link_info result;
+	int interface = cvmx_helper_get_interface_num(ipd_port);
+	int index = cvmx_helper_get_interface_index_num(ipd_port);
+	result.u64 = 0;
+
+	if (cvmx_sysinfo_get()->board_type == CVMX_BOARD_TYPE_SIM) {
+		/* The simulator gives you a simulated full duplex link */
+		result.s.link_up = 1;
+		result.s.full_duplex = 1;
+		result.s.speed = 10000;
+	} else if (cvmx_spi4000_is_present(interface)) {
+		union cvmx_gmxx_rxx_rx_inbnd inband =
+		    cvmx_spi4000_check_speed(interface, index);
+		result.s.link_up = inband.s.status;
+		result.s.full_duplex = inband.s.duplex;
+		switch (inband.s.speed) {
+		case 0: /* 10 Mbps */
+			result.s.speed = 10;
+			break;
+		case 1: /* 100 Mbps */
+			result.s.speed = 100;
+			break;
+		case 2: /* 1 Gbps */
+			result.s.speed = 1000;
+			break;
+		case 3: /* Illegal */
+			result.s.speed = 0;
+			result.s.link_up = 0;
+			break;
+		}
+	} else {
+		/* For generic SPI we can't determine the link, just return some
+		   sane results */
+		result.s.link_up = 1;
+		result.s.full_duplex = 1;
+		result.s.speed = 10000;
+	}
+	return result;
+}
+
+/**
+ * Configure an IPD/PKO port for the specified link state. This
+ * function does not influence auto negotiation at the PHY level.
+ * The passed link state must always match the link state returned
+ * by cvmx_helper_link_get().
+ *
+ * @ipd_port:  IPD/PKO port to configure
+ * @link_info: The new link state
+ *
+ * Returns Zero on success, negative on failure
+ */
+int __cvmx_helper_spi_link_set(int ipd_port, union cvmx_helper_link_info link_info)
+{
+	/* Nothing to do. If we have a SPI4000 then the setup was already performed
+	   by cvmx_spi4000_check_speed(). If not then there isn't any link
+	   info */
+	return 0;
+}
diff --git a/arch/mips/cavium-octeon/executive/cvmx-helper-util.c b/arch/mips/cavium-octeon/executive/cvmx-helper-util.c
new file mode 100644
index 000000000..53b912745
--- /dev/null
+++ b/arch/mips/cavium-octeon/executive/cvmx-helper-util.c
@@ -0,0 +1,363 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ * Small helper utilities.
+ */
+#include <linux/kernel.h>
+
+#include <asm/octeon/octeon.h>
+
+#include <asm/octeon/cvmx-config.h>
+
+#include <asm/octeon/cvmx-fpa.h>
+#include <asm/octeon/cvmx-pip.h>
+#include <asm/octeon/cvmx-pko.h>
+#include <asm/octeon/cvmx-ipd.h>
+#include <asm/octeon/cvmx-spi.h>
+
+#include <asm/octeon/cvmx-helper.h>
+#include <asm/octeon/cvmx-helper-util.h>
+
+#include <asm/octeon/cvmx-ipd-defs.h>
+
+/**
+ * Convert a interface mode into a human readable string
+ *
+ * @mode:   Mode to convert
+ *
+ * Returns String
+ */
+const char *cvmx_helper_interface_mode_to_string(cvmx_helper_interface_mode_t
+						 mode)
+{
+	switch (mode) {
+	case CVMX_HELPER_INTERFACE_MODE_DISABLED:
+		return "DISABLED";
+	case CVMX_HELPER_INTERFACE_MODE_RGMII:
+		return "RGMII";
+	case CVMX_HELPER_INTERFACE_MODE_GMII:
+		return "GMII";
+	case CVMX_HELPER_INTERFACE_MODE_SPI:
+		return "SPI";
+	case CVMX_HELPER_INTERFACE_MODE_PCIE:
+		return "PCIE";
+	case CVMX_HELPER_INTERFACE_MODE_XAUI:
+		return "XAUI";
+	case CVMX_HELPER_INTERFACE_MODE_SGMII:
+		return "SGMII";
+	case CVMX_HELPER_INTERFACE_MODE_PICMG:
+		return "PICMG";
+	case CVMX_HELPER_INTERFACE_MODE_NPI:
+		return "NPI";
+	case CVMX_HELPER_INTERFACE_MODE_LOOP:
+		return "LOOP";
+	}
+	return "UNKNOWN";
+}
+
+/**
+ * Setup Random Early Drop on a specific input queue
+ *
+ * @queue:  Input queue to setup RED on (0-7)
+ * @pass_thresh:
+ *		 Packets will begin slowly dropping when there are less than
+ *		 this many packet buffers free in FPA 0.
+ * @drop_thresh:
+ *		 All incoming packets will be dropped when there are less
+ *		 than this many free packet buffers in FPA 0.
+ * Returns Zero on success. Negative on failure
+ */
+static int cvmx_helper_setup_red_queue(int queue, int pass_thresh,
+				       int drop_thresh)
+{
+	union cvmx_ipd_qosx_red_marks red_marks;
+	union cvmx_ipd_red_quex_param red_param;
+
+	/* Set RED to begin dropping packets when there are pass_thresh buffers
+	   left. It will linearly drop more packets until reaching drop_thresh
+	   buffers */
+	red_marks.u64 = 0;
+	red_marks.s.drop = drop_thresh;
+	red_marks.s.pass = pass_thresh;
+	cvmx_write_csr(CVMX_IPD_QOSX_RED_MARKS(queue), red_marks.u64);
+
+	/* Use the actual queue 0 counter, not the average */
+	red_param.u64 = 0;
+	red_param.s.prb_con =
+	    (255ul << 24) / (red_marks.s.pass - red_marks.s.drop);
+	red_param.s.avg_con = 1;
+	red_param.s.new_con = 255;
+	red_param.s.use_pcnt = 1;
+	cvmx_write_csr(CVMX_IPD_RED_QUEX_PARAM(queue), red_param.u64);
+	return 0;
+}
+
+/**
+ * Setup Random Early Drop to automatically begin dropping packets.
+ *
+ * @pass_thresh:
+ *		 Packets will begin slowly dropping when there are less than
+ *		 this many packet buffers free in FPA 0.
+ * @drop_thresh:
+ *		 All incoming packets will be dropped when there are less
+ *		 than this many free packet buffers in FPA 0.
+ * Returns Zero on success. Negative on failure
+ */
+int cvmx_helper_setup_red(int pass_thresh, int drop_thresh)
+{
+	union cvmx_ipd_portx_bp_page_cnt page_cnt;
+	union cvmx_ipd_bp_prt_red_end ipd_bp_prt_red_end;
+	union cvmx_ipd_red_port_enable red_port_enable;
+	int queue;
+	int interface;
+	int port;
+
+	/* Disable backpressure based on queued buffers. It needs SW support */
+	page_cnt.u64 = 0;
+	page_cnt.s.bp_enb = 0;
+	page_cnt.s.page_cnt = 100;
+	for (interface = 0; interface < 2; interface++) {
+		for (port = cvmx_helper_get_first_ipd_port(interface);
+		     port < cvmx_helper_get_last_ipd_port(interface); port++)
+			cvmx_write_csr(CVMX_IPD_PORTX_BP_PAGE_CNT(port),
+				       page_cnt.u64);
+	}
+
+	for (queue = 0; queue < 8; queue++)
+		cvmx_helper_setup_red_queue(queue, pass_thresh, drop_thresh);
+
+	/* Shutoff the dropping based on the per port page count. SW isn't
+	   decrementing it right now */
+	ipd_bp_prt_red_end.u64 = 0;
+	ipd_bp_prt_red_end.s.prt_enb = 0;
+	cvmx_write_csr(CVMX_IPD_BP_PRT_RED_END, ipd_bp_prt_red_end.u64);
+
+	red_port_enable.u64 = 0;
+	red_port_enable.s.prt_enb = 0xfffffffffull;
+	red_port_enable.s.avg_dly = 10000;
+	red_port_enable.s.prb_dly = 10000;
+	cvmx_write_csr(CVMX_IPD_RED_PORT_ENABLE, red_port_enable.u64);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(cvmx_helper_setup_red);
+
+/**
+ * Setup the common GMX settings that determine the number of
+ * ports. These setting apply to almost all configurations of all
+ * chips.
+ *
+ * @interface: Interface to configure
+ * @num_ports: Number of ports on the interface
+ *
+ * Returns Zero on success, negative on failure
+ */
+int __cvmx_helper_setup_gmx(int interface, int num_ports)
+{
+	union cvmx_gmxx_tx_prts gmx_tx_prts;
+	union cvmx_gmxx_rx_prts gmx_rx_prts;
+	union cvmx_pko_reg_gmx_port_mode pko_mode;
+	union cvmx_gmxx_txx_thresh gmx_tx_thresh;
+	int index;
+
+	/* Tell GMX the number of TX ports on this interface */
+	gmx_tx_prts.u64 = cvmx_read_csr(CVMX_GMXX_TX_PRTS(interface));
+	gmx_tx_prts.s.prts = num_ports;
+	cvmx_write_csr(CVMX_GMXX_TX_PRTS(interface), gmx_tx_prts.u64);
+
+	/* Tell GMX the number of RX ports on this interface.  This only
+	 ** applies to *GMII and XAUI ports */
+	if (cvmx_helper_interface_get_mode(interface) ==
+	    CVMX_HELPER_INTERFACE_MODE_RGMII
+	    || cvmx_helper_interface_get_mode(interface) ==
+	    CVMX_HELPER_INTERFACE_MODE_SGMII
+	    || cvmx_helper_interface_get_mode(interface) ==
+	    CVMX_HELPER_INTERFACE_MODE_GMII
+	    || cvmx_helper_interface_get_mode(interface) ==
+	    CVMX_HELPER_INTERFACE_MODE_XAUI) {
+		if (num_ports > 4) {
+			cvmx_dprintf("__cvmx_helper_setup_gmx: Illegal "
+				     "num_ports\n");
+			return -1;
+		}
+
+		gmx_rx_prts.u64 = cvmx_read_csr(CVMX_GMXX_RX_PRTS(interface));
+		gmx_rx_prts.s.prts = num_ports;
+		cvmx_write_csr(CVMX_GMXX_RX_PRTS(interface), gmx_rx_prts.u64);
+	}
+
+	/* Skip setting CVMX_PKO_REG_GMX_PORT_MODE on 30XX, 31XX, and 50XX */
+	if (!OCTEON_IS_MODEL(OCTEON_CN30XX) && !OCTEON_IS_MODEL(OCTEON_CN31XX)
+	    && !OCTEON_IS_MODEL(OCTEON_CN50XX)) {
+		/* Tell PKO the number of ports on this interface */
+		pko_mode.u64 = cvmx_read_csr(CVMX_PKO_REG_GMX_PORT_MODE);
+		if (interface == 0) {
+			if (num_ports == 1)
+				pko_mode.s.mode0 = 4;
+			else if (num_ports == 2)
+				pko_mode.s.mode0 = 3;
+			else if (num_ports <= 4)
+				pko_mode.s.mode0 = 2;
+			else if (num_ports <= 8)
+				pko_mode.s.mode0 = 1;
+			else
+				pko_mode.s.mode0 = 0;
+		} else {
+			if (num_ports == 1)
+				pko_mode.s.mode1 = 4;
+			else if (num_ports == 2)
+				pko_mode.s.mode1 = 3;
+			else if (num_ports <= 4)
+				pko_mode.s.mode1 = 2;
+			else if (num_ports <= 8)
+				pko_mode.s.mode1 = 1;
+			else
+				pko_mode.s.mode1 = 0;
+		}
+		cvmx_write_csr(CVMX_PKO_REG_GMX_PORT_MODE, pko_mode.u64);
+	}
+
+	/*
+	 * Set GMX to buffer as much data as possible before starting
+	 * transmit.  This reduces the chances that we have a TX under
+	 * run due to memory contention. Any packet that fits entirely
+	 * in the GMX FIFO can never have an under run regardless of
+	 * memory load.
+	 */
+	gmx_tx_thresh.u64 = cvmx_read_csr(CVMX_GMXX_TXX_THRESH(0, interface));
+	if (OCTEON_IS_MODEL(OCTEON_CN30XX) || OCTEON_IS_MODEL(OCTEON_CN31XX)
+	    || OCTEON_IS_MODEL(OCTEON_CN50XX)) {
+		/* These chips have a fixed max threshold of 0x40 */
+		gmx_tx_thresh.s.cnt = 0x40;
+	} else {
+		/* Choose the max value for the number of ports */
+		if (num_ports <= 1)
+			gmx_tx_thresh.s.cnt = 0x100 / 1;
+		else if (num_ports == 2)
+			gmx_tx_thresh.s.cnt = 0x100 / 2;
+		else
+			gmx_tx_thresh.s.cnt = 0x100 / 4;
+	}
+	/*
+	 * SPI and XAUI can have lots of ports but the GMX hardware
+	 * only ever has a max of 4.
+	 */
+	if (num_ports > 4)
+		num_ports = 4;
+	for (index = 0; index < num_ports; index++)
+		cvmx_write_csr(CVMX_GMXX_TXX_THRESH(index, interface),
+			       gmx_tx_thresh.u64);
+
+	return 0;
+}
+
+/**
+ * Returns the IPD/PKO port number for a port on the given
+ * interface.
+ *
+ * @interface: Interface to use
+ * @port:      Port on the interface
+ *
+ * Returns IPD/PKO port number
+ */
+int cvmx_helper_get_ipd_port(int interface, int port)
+{
+	switch (interface) {
+	case 0:
+		return port;
+	case 1:
+		return port + 16;
+	case 2:
+		return port + 32;
+	case 3:
+		return port + 36;
+	case 4:
+		return port + 40;
+	case 5:
+		return port + 44;
+	}
+	return -1;
+}
+EXPORT_SYMBOL_GPL(cvmx_helper_get_ipd_port);
+
+/**
+ * Returns the interface number for an IPD/PKO port number.
+ *
+ * @ipd_port: IPD/PKO port number
+ *
+ * Returns Interface number
+ */
+int cvmx_helper_get_interface_num(int ipd_port)
+{
+	if (ipd_port < 16)
+		return 0;
+	else if (ipd_port < 32)
+		return 1;
+	else if (ipd_port < 36)
+		return 2;
+	else if (ipd_port < 40)
+		return 3;
+	else if (ipd_port < 44)
+		return 4;
+	else if (ipd_port < 48)
+		return 5;
+	else
+		cvmx_dprintf("cvmx_helper_get_interface_num: Illegal IPD "
+			     "port number\n");
+
+	return -1;
+}
+EXPORT_SYMBOL_GPL(cvmx_helper_get_interface_num);
+
+/**
+ * Returns the interface index number for an IPD/PKO port
+ * number.
+ *
+ * @ipd_port: IPD/PKO port number
+ *
+ * Returns Interface index number
+ */
+int cvmx_helper_get_interface_index_num(int ipd_port)
+{
+	if (ipd_port < 32)
+		return ipd_port & 15;
+	else if (ipd_port < 36)
+		return ipd_port & 3;
+	else if (ipd_port < 40)
+		return ipd_port & 3;
+	else if (ipd_port < 44)
+		return ipd_port & 3;
+	else if (ipd_port < 48)
+		return ipd_port & 3;
+	else
+		cvmx_dprintf("cvmx_helper_get_interface_index_num: "
+			     "Illegal IPD port number\n");
+
+	return -1;
+}
+EXPORT_SYMBOL_GPL(cvmx_helper_get_interface_index_num);
diff --git a/arch/mips/cavium-octeon/executive/cvmx-helper-xaui.c b/arch/mips/cavium-octeon/executive/cvmx-helper-xaui.c
new file mode 100644
index 000000000..a92632223
--- /dev/null
+++ b/arch/mips/cavium-octeon/executive/cvmx-helper-xaui.c
@@ -0,0 +1,322 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (C) 2003-2018 Cavium, Inc.
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ * Functions for XAUI initialization, configuration,
+ * and monitoring.
+ *
+ */
+
+#include <asm/octeon/octeon.h>
+
+#include <asm/octeon/cvmx-config.h>
+
+#include <asm/octeon/cvmx-helper.h>
+
+#include <asm/octeon/cvmx-pko-defs.h>
+#include <asm/octeon/cvmx-gmxx-defs.h>
+#include <asm/octeon/cvmx-pcsx-defs.h>
+#include <asm/octeon/cvmx-pcsxx-defs.h>
+
+int __cvmx_helper_xaui_enumerate(int interface)
+{
+	union cvmx_gmxx_hg2_control gmx_hg2_control;
+
+	/* If HiGig2 is enabled return 16 ports, otherwise return 1 port */
+	gmx_hg2_control.u64 = cvmx_read_csr(CVMX_GMXX_HG2_CONTROL(interface));
+	if (gmx_hg2_control.s.hg2tx_en)
+		return 16;
+	else
+		return 1;
+}
+
+/*
+ * Probe a XAUI interface and determine the number of ports
+ * connected to it. The XAUI interface should still be down
+ * after this call.
+ *
+ * @interface: Interface to probe
+ *
+ * Returns Number of ports on the interface. Zero to disable.
+ */
+int __cvmx_helper_xaui_probe(int interface)
+{
+	int i;
+	union cvmx_gmxx_inf_mode mode;
+
+	/*
+	 * Due to errata GMX-700 on CN56XXp1.x and CN52XXp1.x, the
+	 * interface needs to be enabled before IPD otherwise per port
+	 * backpressure may not work properly.
+	 */
+	mode.u64 = cvmx_read_csr(CVMX_GMXX_INF_MODE(interface));
+	mode.s.en = 1;
+	cvmx_write_csr(CVMX_GMXX_INF_MODE(interface), mode.u64);
+
+	__cvmx_helper_setup_gmx(interface, 1);
+
+	/*
+	 * Setup PKO to support 16 ports for HiGig2 virtual
+	 * ports. We're pointing all of the PKO packet ports for this
+	 * interface to the XAUI. This allows us to use HiGig2
+	 * backpressure per port.
+	 */
+	for (i = 0; i < 16; i++) {
+		union cvmx_pko_mem_port_ptrs pko_mem_port_ptrs;
+		pko_mem_port_ptrs.u64 = 0;
+		/*
+		 * We set each PKO port to have equal priority in a
+		 * round robin fashion.
+		 */
+		pko_mem_port_ptrs.s.static_p = 0;
+		pko_mem_port_ptrs.s.qos_mask = 0xff;
+		/* All PKO ports map to the same XAUI hardware port */
+		pko_mem_port_ptrs.s.eid = interface * 4;
+		pko_mem_port_ptrs.s.pid = interface * 16 + i;
+		cvmx_write_csr(CVMX_PKO_MEM_PORT_PTRS, pko_mem_port_ptrs.u64);
+	}
+	return __cvmx_helper_xaui_enumerate(interface);
+}
+
+/*
+ * Bringup and enable a XAUI interface. After this call packet
+ * I/O should be fully functional. This is called with IPD
+ * enabled but PKO disabled.
+ *
+ * @interface: Interface to bring up
+ *
+ * Returns Zero on success, negative on failure
+ */
+int __cvmx_helper_xaui_enable(int interface)
+{
+	union cvmx_gmxx_prtx_cfg gmx_cfg;
+	union cvmx_pcsxx_control1_reg xauiCtl;
+	union cvmx_pcsxx_misc_ctl_reg xauiMiscCtl;
+	union cvmx_gmxx_tx_xaui_ctl gmxXauiTxCtl;
+	union cvmx_gmxx_rxx_int_en gmx_rx_int_en;
+	union cvmx_gmxx_tx_int_en gmx_tx_int_en;
+	union cvmx_pcsxx_int_en_reg pcsx_int_en_reg;
+
+	/* Setup PKND */
+	if (octeon_has_feature(OCTEON_FEATURE_PKND)) {
+		gmx_cfg.u64 = cvmx_read_csr(CVMX_GMXX_PRTX_CFG(0, interface));
+		gmx_cfg.s.pknd = cvmx_helper_get_ipd_port(interface, 0);
+		cvmx_write_csr(CVMX_GMXX_PRTX_CFG(0, interface), gmx_cfg.u64);
+	}
+
+	/* (1) Interface has already been enabled. */
+
+	/* (2) Disable GMX. */
+	xauiMiscCtl.u64 = cvmx_read_csr(CVMX_PCSXX_MISC_CTL_REG(interface));
+	xauiMiscCtl.s.gmxeno = 1;
+	cvmx_write_csr(CVMX_PCSXX_MISC_CTL_REG(interface), xauiMiscCtl.u64);
+
+	/* (3) Disable GMX and PCSX interrupts. */
+	gmx_rx_int_en.u64 = cvmx_read_csr(CVMX_GMXX_RXX_INT_EN(0, interface));
+	cvmx_write_csr(CVMX_GMXX_RXX_INT_EN(0, interface), 0x0);
+	gmx_tx_int_en.u64 = cvmx_read_csr(CVMX_GMXX_TX_INT_EN(interface));
+	cvmx_write_csr(CVMX_GMXX_TX_INT_EN(interface), 0x0);
+	pcsx_int_en_reg.u64 = cvmx_read_csr(CVMX_PCSXX_INT_EN_REG(interface));
+	cvmx_write_csr(CVMX_PCSXX_INT_EN_REG(interface), 0x0);
+
+	/* (4) Bring up the PCSX and GMX reconciliation layer. */
+	/* (4)a Set polarity and lane swapping. */
+	/* (4)b */
+	gmxXauiTxCtl.u64 = cvmx_read_csr(CVMX_GMXX_TX_XAUI_CTL(interface));
+	/* Enable better IFG packing and improves performance */
+	gmxXauiTxCtl.s.dic_en = 1;
+	gmxXauiTxCtl.s.uni_en = 0;
+	cvmx_write_csr(CVMX_GMXX_TX_XAUI_CTL(interface), gmxXauiTxCtl.u64);
+
+	/* (4)c Aply reset sequence */
+	xauiCtl.u64 = cvmx_read_csr(CVMX_PCSXX_CONTROL1_REG(interface));
+	xauiCtl.s.lo_pwr = 0;
+
+	/* Issuing a reset here seems to hang some CN66XX/CN68XX chips. */
+	if (!OCTEON_IS_MODEL(OCTEON_CN66XX) &&
+	    !OCTEON_IS_MODEL(OCTEON_CN68XX_PASS1_X) &&
+	    !OCTEON_IS_MODEL(OCTEON_CN68XX_PASS2_X))
+		xauiCtl.s.reset = 1;
+
+	cvmx_write_csr(CVMX_PCSXX_CONTROL1_REG(interface), xauiCtl.u64);
+
+	/* Wait for PCS to come out of reset */
+	if (CVMX_WAIT_FOR_FIELD64
+	    (CVMX_PCSXX_CONTROL1_REG(interface), union cvmx_pcsxx_control1_reg,
+	     reset, ==, 0, 10000))
+		return -1;
+	/* Wait for PCS to be aligned */
+	if (CVMX_WAIT_FOR_FIELD64
+	    (CVMX_PCSXX_10GBX_STATUS_REG(interface),
+	     union cvmx_pcsxx_10gbx_status_reg, alignd, ==, 1, 10000))
+		return -1;
+	/* Wait for RX to be ready */
+	if (CVMX_WAIT_FOR_FIELD64
+	    (CVMX_GMXX_RX_XAUI_CTL(interface), union cvmx_gmxx_rx_xaui_ctl,
+		    status, ==, 0, 10000))
+		return -1;
+
+	/* (6) Configure GMX */
+	gmx_cfg.u64 = cvmx_read_csr(CVMX_GMXX_PRTX_CFG(0, interface));
+	gmx_cfg.s.en = 0;
+	cvmx_write_csr(CVMX_GMXX_PRTX_CFG(0, interface), gmx_cfg.u64);
+
+	/* Wait for GMX RX to be idle */
+	if (CVMX_WAIT_FOR_FIELD64
+	    (CVMX_GMXX_PRTX_CFG(0, interface), union cvmx_gmxx_prtx_cfg,
+		    rx_idle, ==, 1, 10000))
+		return -1;
+	/* Wait for GMX TX to be idle */
+	if (CVMX_WAIT_FOR_FIELD64
+	    (CVMX_GMXX_PRTX_CFG(0, interface), union cvmx_gmxx_prtx_cfg,
+		    tx_idle, ==, 1, 10000))
+		return -1;
+
+	/* GMX configure */
+	gmx_cfg.u64 = cvmx_read_csr(CVMX_GMXX_PRTX_CFG(0, interface));
+	gmx_cfg.s.speed = 1;
+	gmx_cfg.s.speed_msb = 0;
+	gmx_cfg.s.slottime = 1;
+	cvmx_write_csr(CVMX_GMXX_TX_PRTS(interface), 1);
+	cvmx_write_csr(CVMX_GMXX_TXX_SLOT(0, interface), 512);
+	cvmx_write_csr(CVMX_GMXX_TXX_BURST(0, interface), 8192);
+	cvmx_write_csr(CVMX_GMXX_PRTX_CFG(0, interface), gmx_cfg.u64);
+
+	/* (7) Clear out any error state */
+	cvmx_write_csr(CVMX_GMXX_RXX_INT_REG(0, interface),
+		       cvmx_read_csr(CVMX_GMXX_RXX_INT_REG(0, interface)));
+	cvmx_write_csr(CVMX_GMXX_TX_INT_REG(interface),
+		       cvmx_read_csr(CVMX_GMXX_TX_INT_REG(interface)));
+	cvmx_write_csr(CVMX_PCSXX_INT_REG(interface),
+		       cvmx_read_csr(CVMX_PCSXX_INT_REG(interface)));
+
+	/* Wait for receive link */
+	if (CVMX_WAIT_FOR_FIELD64
+	    (CVMX_PCSXX_STATUS1_REG(interface), union cvmx_pcsxx_status1_reg,
+	     rcv_lnk, ==, 1, 10000))
+		return -1;
+	if (CVMX_WAIT_FOR_FIELD64
+	    (CVMX_PCSXX_STATUS2_REG(interface), union cvmx_pcsxx_status2_reg,
+	     xmtflt, ==, 0, 10000))
+		return -1;
+	if (CVMX_WAIT_FOR_FIELD64
+	    (CVMX_PCSXX_STATUS2_REG(interface), union cvmx_pcsxx_status2_reg,
+	     rcvflt, ==, 0, 10000))
+		return -1;
+
+	cvmx_write_csr(CVMX_GMXX_RXX_INT_EN(0, interface), gmx_rx_int_en.u64);
+	cvmx_write_csr(CVMX_GMXX_TX_INT_EN(interface), gmx_tx_int_en.u64);
+	cvmx_write_csr(CVMX_PCSXX_INT_EN_REG(interface), pcsx_int_en_reg.u64);
+
+	/* (8) Enable packet reception */
+	xauiMiscCtl.s.gmxeno = 0;
+	cvmx_write_csr(CVMX_PCSXX_MISC_CTL_REG(interface), xauiMiscCtl.u64);
+
+	gmx_cfg.u64 = cvmx_read_csr(CVMX_GMXX_PRTX_CFG(0, interface));
+	gmx_cfg.s.en = 1;
+	cvmx_write_csr(CVMX_GMXX_PRTX_CFG(0, interface), gmx_cfg.u64);
+
+	__cvmx_interrupt_pcsx_intx_en_reg_enable(0, interface);
+	__cvmx_interrupt_pcsx_intx_en_reg_enable(1, interface);
+	__cvmx_interrupt_pcsx_intx_en_reg_enable(2, interface);
+	__cvmx_interrupt_pcsx_intx_en_reg_enable(3, interface);
+	__cvmx_interrupt_pcsxx_int_en_reg_enable(interface);
+	__cvmx_interrupt_gmxx_enable(interface);
+
+	return 0;
+}
+
+/*
+ * Return the link state of an IPD/PKO port as returned by
+ * auto negotiation. The result of this function may not match
+ * Octeon's link config if auto negotiation has changed since
+ * the last call to cvmx_helper_link_set().
+ *
+ * @ipd_port: IPD/PKO port to query
+ *
+ * Returns Link state
+ */
+union cvmx_helper_link_info __cvmx_helper_xaui_link_get(int ipd_port)
+{
+	int interface = cvmx_helper_get_interface_num(ipd_port);
+	union cvmx_gmxx_tx_xaui_ctl gmxx_tx_xaui_ctl;
+	union cvmx_gmxx_rx_xaui_ctl gmxx_rx_xaui_ctl;
+	union cvmx_pcsxx_status1_reg pcsxx_status1_reg;
+	union cvmx_helper_link_info result;
+
+	gmxx_tx_xaui_ctl.u64 = cvmx_read_csr(CVMX_GMXX_TX_XAUI_CTL(interface));
+	gmxx_rx_xaui_ctl.u64 = cvmx_read_csr(CVMX_GMXX_RX_XAUI_CTL(interface));
+	pcsxx_status1_reg.u64 =
+	    cvmx_read_csr(CVMX_PCSXX_STATUS1_REG(interface));
+	result.u64 = 0;
+
+	/* Only return a link if both RX and TX are happy */
+	if ((gmxx_tx_xaui_ctl.s.ls == 0) && (gmxx_rx_xaui_ctl.s.status == 0) &&
+	    (pcsxx_status1_reg.s.rcv_lnk == 1)) {
+		result.s.link_up = 1;
+		result.s.full_duplex = 1;
+		result.s.speed = 10000;
+	} else {
+		/* Disable GMX and PCSX interrupts. */
+		cvmx_write_csr(CVMX_GMXX_RXX_INT_EN(0, interface), 0x0);
+		cvmx_write_csr(CVMX_GMXX_TX_INT_EN(interface), 0x0);
+		cvmx_write_csr(CVMX_PCSXX_INT_EN_REG(interface), 0x0);
+	}
+	return result;
+}
+
+/*
+ * Configure an IPD/PKO port for the specified link state. This
+ * function does not influence auto negotiation at the PHY level.
+ * The passed link state must always match the link state returned
+ * by cvmx_helper_link_get().
+ *
+ * @ipd_port:  IPD/PKO port to configure
+ * @link_info: The new link state
+ *
+ * Returns Zero on success, negative on failure
+ */
+int __cvmx_helper_xaui_link_set(int ipd_port, union cvmx_helper_link_info link_info)
+{
+	int interface = cvmx_helper_get_interface_num(ipd_port);
+	union cvmx_gmxx_tx_xaui_ctl gmxx_tx_xaui_ctl;
+	union cvmx_gmxx_rx_xaui_ctl gmxx_rx_xaui_ctl;
+
+	gmxx_tx_xaui_ctl.u64 = cvmx_read_csr(CVMX_GMXX_TX_XAUI_CTL(interface));
+	gmxx_rx_xaui_ctl.u64 = cvmx_read_csr(CVMX_GMXX_RX_XAUI_CTL(interface));
+
+	/* If the link shouldn't be up, then just return */
+	if (!link_info.s.link_up)
+		return 0;
+
+	/* Do nothing if both RX and TX are happy */
+	if ((gmxx_tx_xaui_ctl.s.ls == 0) && (gmxx_rx_xaui_ctl.s.status == 0))
+		return 0;
+
+	/* Bring the link up */
+	return __cvmx_helper_xaui_enable(interface);
+}
diff --git a/arch/mips/cavium-octeon/executive/cvmx-helper.c b/arch/mips/cavium-octeon/executive/cvmx-helper.c
new file mode 100644
index 000000000..9abfc4bf9
--- /dev/null
+++ b/arch/mips/cavium-octeon/executive/cvmx-helper.c
@@ -0,0 +1,1172 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ *
+ * Helper functions for common, but complicated tasks.
+ *
+ */
+#include <linux/bug.h>
+#include <asm/octeon/octeon.h>
+
+#include <asm/octeon/cvmx-config.h>
+
+#include <asm/octeon/cvmx-fpa.h>
+#include <asm/octeon/cvmx-pip.h>
+#include <asm/octeon/cvmx-pko.h>
+#include <asm/octeon/cvmx-ipd.h>
+#include <asm/octeon/cvmx-spi.h>
+#include <asm/octeon/cvmx-helper.h>
+#include <asm/octeon/cvmx-helper-board.h>
+
+#include <asm/octeon/cvmx-pip-defs.h>
+#include <asm/octeon/cvmx-asxx-defs.h>
+
+/* Port count per interface */
+static int interface_port_count[9];
+
+/**
+ * Return the number of interfaces the chip has. Each interface
+ * may have multiple ports. Most chips support two interfaces,
+ * but the CNX0XX and CNX1XX are exceptions. These only support
+ * one interface.
+ *
+ * Returns Number of interfaces on chip
+ */
+int cvmx_helper_get_number_of_interfaces(void)
+{
+	if (OCTEON_IS_MODEL(OCTEON_CN68XX))
+		return 9;
+	if (OCTEON_IS_MODEL(OCTEON_CN66XX)) {
+		if (OCTEON_IS_MODEL(OCTEON_CN66XX_PASS1_0))
+			return 7;
+		else
+			return 8;
+	}
+	if (OCTEON_IS_MODEL(OCTEON_CN56XX) || OCTEON_IS_MODEL(OCTEON_CN52XX))
+		return 4;
+	if (OCTEON_IS_MODEL(OCTEON_CN7XXX))
+		return 5;
+	else
+		return 3;
+}
+EXPORT_SYMBOL_GPL(cvmx_helper_get_number_of_interfaces);
+
+/**
+ * Return the number of ports on an interface. Depending on the
+ * chip and configuration, this can be 1-16. A value of 0
+ * specifies that the interface doesn't exist or isn't usable.
+ *
+ * @interface: Interface to get the port count for
+ *
+ * Returns Number of ports on interface. Can be Zero.
+ */
+int cvmx_helper_ports_on_interface(int interface)
+{
+	return interface_port_count[interface];
+}
+EXPORT_SYMBOL_GPL(cvmx_helper_ports_on_interface);
+
+/**
+ * @INTERNAL
+ * Return interface mode for CN68xx.
+ */
+static cvmx_helper_interface_mode_t __cvmx_get_mode_cn68xx(int interface)
+{
+	union cvmx_mio_qlmx_cfg qlm_cfg;
+	switch (interface) {
+	case 0:
+		qlm_cfg.u64 = cvmx_read_csr(CVMX_MIO_QLMX_CFG(0));
+		/* QLM is disabled when QLM SPD is 15. */
+		if (qlm_cfg.s.qlm_spd == 15)
+			return CVMX_HELPER_INTERFACE_MODE_DISABLED;
+
+		if (qlm_cfg.s.qlm_cfg == 2)
+			return CVMX_HELPER_INTERFACE_MODE_SGMII;
+		else if (qlm_cfg.s.qlm_cfg == 3)
+			return CVMX_HELPER_INTERFACE_MODE_XAUI;
+		else
+			return CVMX_HELPER_INTERFACE_MODE_DISABLED;
+	case 2:
+	case 3:
+	case 4:
+		qlm_cfg.u64 = cvmx_read_csr(CVMX_MIO_QLMX_CFG(interface));
+		/* QLM is disabled when QLM SPD is 15. */
+		if (qlm_cfg.s.qlm_spd == 15)
+			return CVMX_HELPER_INTERFACE_MODE_DISABLED;
+
+		if (qlm_cfg.s.qlm_cfg == 2)
+			return CVMX_HELPER_INTERFACE_MODE_SGMII;
+		else if (qlm_cfg.s.qlm_cfg == 3)
+			return CVMX_HELPER_INTERFACE_MODE_XAUI;
+		else
+			return CVMX_HELPER_INTERFACE_MODE_DISABLED;
+	case 7:
+		qlm_cfg.u64 = cvmx_read_csr(CVMX_MIO_QLMX_CFG(3));
+		/* QLM is disabled when QLM SPD is 15. */
+		if (qlm_cfg.s.qlm_spd == 15) {
+			return CVMX_HELPER_INTERFACE_MODE_DISABLED;
+		} else if (qlm_cfg.s.qlm_cfg != 0) {
+			qlm_cfg.u64 = cvmx_read_csr(CVMX_MIO_QLMX_CFG(1));
+			if (qlm_cfg.s.qlm_cfg != 0)
+				return CVMX_HELPER_INTERFACE_MODE_DISABLED;
+		}
+		return CVMX_HELPER_INTERFACE_MODE_NPI;
+	case 8:
+		return CVMX_HELPER_INTERFACE_MODE_LOOP;
+	default:
+		return CVMX_HELPER_INTERFACE_MODE_DISABLED;
+	}
+}
+
+/**
+ * @INTERNAL
+ * Return interface mode for an Octeon II
+ */
+static cvmx_helper_interface_mode_t __cvmx_get_mode_octeon2(int interface)
+{
+	union cvmx_gmxx_inf_mode mode;
+
+	if (OCTEON_IS_MODEL(OCTEON_CN68XX))
+		return __cvmx_get_mode_cn68xx(interface);
+
+	if (interface == 2)
+		return CVMX_HELPER_INTERFACE_MODE_NPI;
+
+	if (interface == 3)
+		return CVMX_HELPER_INTERFACE_MODE_LOOP;
+
+	/* Only present in CN63XX & CN66XX Octeon model */
+	if ((OCTEON_IS_MODEL(OCTEON_CN63XX) &&
+	     (interface == 4 || interface == 5)) ||
+	    (OCTEON_IS_MODEL(OCTEON_CN66XX) &&
+	     interface >= 4 && interface <= 7)) {
+		return CVMX_HELPER_INTERFACE_MODE_DISABLED;
+	}
+
+	if (OCTEON_IS_MODEL(OCTEON_CN66XX)) {
+		union cvmx_mio_qlmx_cfg mio_qlm_cfg;
+
+		/* QLM2 is SGMII0 and QLM1 is SGMII1 */
+		if (interface == 0)
+			mio_qlm_cfg.u64 = cvmx_read_csr(CVMX_MIO_QLMX_CFG(2));
+		else if (interface == 1)
+			mio_qlm_cfg.u64 = cvmx_read_csr(CVMX_MIO_QLMX_CFG(1));
+		else
+			return CVMX_HELPER_INTERFACE_MODE_DISABLED;
+
+		if (mio_qlm_cfg.s.qlm_spd == 15)
+			return CVMX_HELPER_INTERFACE_MODE_DISABLED;
+
+		if (mio_qlm_cfg.s.qlm_cfg == 9)
+			return CVMX_HELPER_INTERFACE_MODE_SGMII;
+		else if (mio_qlm_cfg.s.qlm_cfg == 11)
+			return CVMX_HELPER_INTERFACE_MODE_XAUI;
+		else
+			return CVMX_HELPER_INTERFACE_MODE_DISABLED;
+	} else if (OCTEON_IS_MODEL(OCTEON_CN61XX)) {
+		union cvmx_mio_qlmx_cfg qlm_cfg;
+
+		if (interface == 0) {
+			qlm_cfg.u64 = cvmx_read_csr(CVMX_MIO_QLMX_CFG(2));
+			if (qlm_cfg.s.qlm_cfg == 2)
+				return CVMX_HELPER_INTERFACE_MODE_SGMII;
+			else if (qlm_cfg.s.qlm_cfg == 3)
+				return CVMX_HELPER_INTERFACE_MODE_XAUI;
+			else
+				return CVMX_HELPER_INTERFACE_MODE_DISABLED;
+		} else if (interface == 1) {
+			qlm_cfg.u64 = cvmx_read_csr(CVMX_MIO_QLMX_CFG(0));
+			if (qlm_cfg.s.qlm_cfg == 2)
+				return CVMX_HELPER_INTERFACE_MODE_SGMII;
+			else if (qlm_cfg.s.qlm_cfg == 3)
+				return CVMX_HELPER_INTERFACE_MODE_XAUI;
+			else
+				return CVMX_HELPER_INTERFACE_MODE_DISABLED;
+		}
+	} else if (OCTEON_IS_MODEL(OCTEON_CNF71XX)) {
+		if (interface == 0) {
+			union cvmx_mio_qlmx_cfg qlm_cfg;
+			qlm_cfg.u64 = cvmx_read_csr(CVMX_MIO_QLMX_CFG(0));
+			if (qlm_cfg.s.qlm_cfg == 2)
+				return CVMX_HELPER_INTERFACE_MODE_SGMII;
+		}
+		return CVMX_HELPER_INTERFACE_MODE_DISABLED;
+	}
+
+	if (interface == 1 && OCTEON_IS_MODEL(OCTEON_CN63XX))
+		return CVMX_HELPER_INTERFACE_MODE_DISABLED;
+
+	mode.u64 = cvmx_read_csr(CVMX_GMXX_INF_MODE(interface));
+
+	if (OCTEON_IS_MODEL(OCTEON_CN63XX)) {
+		switch (mode.cn61xx.mode) {
+		case 0:
+			return CVMX_HELPER_INTERFACE_MODE_SGMII;
+		case 1:
+			return CVMX_HELPER_INTERFACE_MODE_XAUI;
+		default:
+			return CVMX_HELPER_INTERFACE_MODE_DISABLED;
+		}
+	} else {
+		if (!mode.s.en)
+			return CVMX_HELPER_INTERFACE_MODE_DISABLED;
+
+		if (mode.s.type)
+			return CVMX_HELPER_INTERFACE_MODE_GMII;
+		else
+			return CVMX_HELPER_INTERFACE_MODE_RGMII;
+	}
+}
+
+/**
+ * @INTERNAL
+ * Return interface mode for CN7XXX.
+ */
+static cvmx_helper_interface_mode_t __cvmx_get_mode_cn7xxx(int interface)
+{
+	union cvmx_gmxx_inf_mode mode;
+
+	mode.u64 = cvmx_read_csr(CVMX_GMXX_INF_MODE(interface));
+
+	switch (interface) {
+	case 0:
+	case 1:
+		switch (mode.cn68xx.mode) {
+		case 0:
+			return CVMX_HELPER_INTERFACE_MODE_DISABLED;
+		case 1:
+		case 2:
+			return CVMX_HELPER_INTERFACE_MODE_SGMII;
+		case 3:
+			return CVMX_HELPER_INTERFACE_MODE_XAUI;
+		default:
+			return CVMX_HELPER_INTERFACE_MODE_SGMII;
+		}
+	case 2:
+		return CVMX_HELPER_INTERFACE_MODE_NPI;
+	case 3:
+		return CVMX_HELPER_INTERFACE_MODE_LOOP;
+	case 4:
+		/* TODO: Implement support for AGL (RGMII). */
+		return CVMX_HELPER_INTERFACE_MODE_DISABLED;
+	default:
+		return CVMX_HELPER_INTERFACE_MODE_DISABLED;
+	}
+}
+
+/**
+ * Get the operating mode of an interface. Depending on the Octeon
+ * chip and configuration, this function returns an enumeration
+ * of the type of packet I/O supported by an interface.
+ *
+ * @interface: Interface to probe
+ *
+ * Returns Mode of the interface. Unknown or unsupported interfaces return
+ *	   DISABLED.
+ */
+cvmx_helper_interface_mode_t cvmx_helper_interface_get_mode(int interface)
+{
+	union cvmx_gmxx_inf_mode mode;
+
+	if (interface < 0 ||
+	    interface >= cvmx_helper_get_number_of_interfaces())
+		return CVMX_HELPER_INTERFACE_MODE_DISABLED;
+
+	/*
+	 * OCTEON III models
+	 */
+	if (OCTEON_IS_MODEL(OCTEON_CN7XXX))
+		return __cvmx_get_mode_cn7xxx(interface);
+
+	/*
+	 * Octeon II models
+	 */
+	if (OCTEON_IS_MODEL(OCTEON_CN6XXX) || OCTEON_IS_MODEL(OCTEON_CNF71XX))
+		return __cvmx_get_mode_octeon2(interface);
+
+	/*
+	 * Octeon and Octeon Plus models
+	 */
+	if (interface == 2)
+		return CVMX_HELPER_INTERFACE_MODE_NPI;
+
+	if (interface == 3) {
+		if (OCTEON_IS_MODEL(OCTEON_CN56XX)
+		    || OCTEON_IS_MODEL(OCTEON_CN52XX))
+			return CVMX_HELPER_INTERFACE_MODE_LOOP;
+		else
+			return CVMX_HELPER_INTERFACE_MODE_DISABLED;
+	}
+
+	/* Interface 1 is always disabled on CN31XX and CN30XX */
+	if ((interface == 1)
+	    && (OCTEON_IS_MODEL(OCTEON_CN31XX) || OCTEON_IS_MODEL(OCTEON_CN30XX)
+		|| OCTEON_IS_MODEL(OCTEON_CN50XX)
+		|| OCTEON_IS_MODEL(OCTEON_CN52XX)))
+		return CVMX_HELPER_INTERFACE_MODE_DISABLED;
+
+	mode.u64 = cvmx_read_csr(CVMX_GMXX_INF_MODE(interface));
+
+	if (OCTEON_IS_MODEL(OCTEON_CN56XX) || OCTEON_IS_MODEL(OCTEON_CN52XX)) {
+		switch (mode.cn52xx.mode) {
+		case 0:
+			return CVMX_HELPER_INTERFACE_MODE_DISABLED;
+		case 1:
+			return CVMX_HELPER_INTERFACE_MODE_XAUI;
+		case 2:
+			return CVMX_HELPER_INTERFACE_MODE_SGMII;
+		case 3:
+			return CVMX_HELPER_INTERFACE_MODE_PICMG;
+		default:
+			return CVMX_HELPER_INTERFACE_MODE_DISABLED;
+		}
+	} else {
+		if (!mode.s.en)
+			return CVMX_HELPER_INTERFACE_MODE_DISABLED;
+
+		if (mode.s.type) {
+			if (OCTEON_IS_MODEL(OCTEON_CN38XX)
+			    || OCTEON_IS_MODEL(OCTEON_CN58XX))
+				return CVMX_HELPER_INTERFACE_MODE_SPI;
+			else
+				return CVMX_HELPER_INTERFACE_MODE_GMII;
+		} else
+			return CVMX_HELPER_INTERFACE_MODE_RGMII;
+	}
+}
+EXPORT_SYMBOL_GPL(cvmx_helper_interface_get_mode);
+
+/**
+ * Configure the IPD/PIP tagging and QoS options for a specific
+ * port. This function determines the POW work queue entry
+ * contents for a port. The setup performed here is controlled by
+ * the defines in executive-config.h.
+ *
+ * @ipd_port: Port to configure. This follows the IPD numbering, not the
+ *		   per interface numbering
+ *
+ * Returns Zero on success, negative on failure
+ */
+static int __cvmx_helper_port_setup_ipd(int ipd_port)
+{
+	union cvmx_pip_prt_cfgx port_config;
+	union cvmx_pip_prt_tagx tag_config;
+
+	port_config.u64 = cvmx_read_csr(CVMX_PIP_PRT_CFGX(ipd_port));
+	tag_config.u64 = cvmx_read_csr(CVMX_PIP_PRT_TAGX(ipd_port));
+
+	/* Have each port go to a different POW queue */
+	port_config.s.qos = ipd_port & 0x7;
+
+	/* Process the headers and place the IP header in the work queue */
+	port_config.s.mode = CVMX_HELPER_INPUT_PORT_SKIP_MODE;
+
+	tag_config.s.ip6_src_flag = CVMX_HELPER_INPUT_TAG_IPV6_SRC_IP;
+	tag_config.s.ip6_dst_flag = CVMX_HELPER_INPUT_TAG_IPV6_DST_IP;
+	tag_config.s.ip6_sprt_flag = CVMX_HELPER_INPUT_TAG_IPV6_SRC_PORT;
+	tag_config.s.ip6_dprt_flag = CVMX_HELPER_INPUT_TAG_IPV6_DST_PORT;
+	tag_config.s.ip6_nxth_flag = CVMX_HELPER_INPUT_TAG_IPV6_NEXT_HEADER;
+	tag_config.s.ip4_src_flag = CVMX_HELPER_INPUT_TAG_IPV4_SRC_IP;
+	tag_config.s.ip4_dst_flag = CVMX_HELPER_INPUT_TAG_IPV4_DST_IP;
+	tag_config.s.ip4_sprt_flag = CVMX_HELPER_INPUT_TAG_IPV4_SRC_PORT;
+	tag_config.s.ip4_dprt_flag = CVMX_HELPER_INPUT_TAG_IPV4_DST_PORT;
+	tag_config.s.ip4_pctl_flag = CVMX_HELPER_INPUT_TAG_IPV4_PROTOCOL;
+	tag_config.s.inc_prt_flag = CVMX_HELPER_INPUT_TAG_INPUT_PORT;
+	tag_config.s.tcp6_tag_type = CVMX_HELPER_INPUT_TAG_TYPE;
+	tag_config.s.tcp4_tag_type = CVMX_HELPER_INPUT_TAG_TYPE;
+	tag_config.s.ip6_tag_type = CVMX_HELPER_INPUT_TAG_TYPE;
+	tag_config.s.ip4_tag_type = CVMX_HELPER_INPUT_TAG_TYPE;
+	tag_config.s.non_tag_type = CVMX_HELPER_INPUT_TAG_TYPE;
+	/* Put all packets in group 0. Other groups can be used by the app */
+	tag_config.s.grp = 0;
+
+	cvmx_pip_config_port(ipd_port, port_config, tag_config);
+
+	return 0;
+}
+
+/**
+ * This function sets the interface_port_count[interface] correctly,
+ * without modifying any hardware configuration.  Hardware setup of
+ * the ports will be performed later.
+ *
+ * @interface: Interface to probe
+ *
+ * Returns Zero on success, negative on failure
+ */
+int cvmx_helper_interface_enumerate(int interface)
+{
+	switch (cvmx_helper_interface_get_mode(interface)) {
+		/* These types don't support ports to IPD/PKO */
+	case CVMX_HELPER_INTERFACE_MODE_DISABLED:
+	case CVMX_HELPER_INTERFACE_MODE_PCIE:
+		interface_port_count[interface] = 0;
+		break;
+		/* XAUI is a single high speed port */
+	case CVMX_HELPER_INTERFACE_MODE_XAUI:
+		interface_port_count[interface] =
+		    __cvmx_helper_xaui_enumerate(interface);
+		break;
+		/*
+		 * RGMII/GMII/MII are all treated about the same. Most
+		 * functions refer to these ports as RGMII.
+		 */
+	case CVMX_HELPER_INTERFACE_MODE_RGMII:
+	case CVMX_HELPER_INTERFACE_MODE_GMII:
+		interface_port_count[interface] =
+		    __cvmx_helper_rgmii_enumerate(interface);
+		break;
+		/*
+		 * SPI4 can have 1-16 ports depending on the device at
+		 * the other end.
+		 */
+	case CVMX_HELPER_INTERFACE_MODE_SPI:
+		interface_port_count[interface] =
+		    __cvmx_helper_spi_enumerate(interface);
+		break;
+		/*
+		 * SGMII can have 1-4 ports depending on how many are
+		 * hooked up.
+		 */
+	case CVMX_HELPER_INTERFACE_MODE_SGMII:
+	case CVMX_HELPER_INTERFACE_MODE_PICMG:
+		interface_port_count[interface] =
+		    __cvmx_helper_sgmii_enumerate(interface);
+		break;
+		/* PCI target Network Packet Interface */
+	case CVMX_HELPER_INTERFACE_MODE_NPI:
+		interface_port_count[interface] =
+		    __cvmx_helper_npi_enumerate(interface);
+		break;
+		/*
+		 * Special loopback only ports. These are not the same
+		 * as other ports in loopback mode.
+		 */
+	case CVMX_HELPER_INTERFACE_MODE_LOOP:
+		interface_port_count[interface] =
+		    __cvmx_helper_loop_enumerate(interface);
+		break;
+	}
+
+	interface_port_count[interface] =
+	    __cvmx_helper_board_interface_probe(interface,
+						interface_port_count
+						[interface]);
+
+	/* Make sure all global variables propagate to other cores */
+	CVMX_SYNCWS;
+
+	return 0;
+}
+
+/**
+ * This function probes an interface to determine the actual
+ * number of hardware ports connected to it. It doesn't setup the
+ * ports or enable them. The main goal here is to set the global
+ * interface_port_count[interface] correctly. Hardware setup of the
+ * ports will be performed later.
+ *
+ * @interface: Interface to probe
+ *
+ * Returns Zero on success, negative on failure
+ */
+int cvmx_helper_interface_probe(int interface)
+{
+	cvmx_helper_interface_enumerate(interface);
+	/* At this stage in the game we don't want packets to be moving yet.
+	   The following probe calls should perform hardware setup
+	   needed to determine port counts. Receive must still be disabled */
+	switch (cvmx_helper_interface_get_mode(interface)) {
+		/* These types don't support ports to IPD/PKO */
+	case CVMX_HELPER_INTERFACE_MODE_DISABLED:
+	case CVMX_HELPER_INTERFACE_MODE_PCIE:
+		break;
+		/* XAUI is a single high speed port */
+	case CVMX_HELPER_INTERFACE_MODE_XAUI:
+		__cvmx_helper_xaui_probe(interface);
+		break;
+		/*
+		 * RGMII/GMII/MII are all treated about the same. Most
+		 * functions refer to these ports as RGMII.
+		 */
+	case CVMX_HELPER_INTERFACE_MODE_RGMII:
+	case CVMX_HELPER_INTERFACE_MODE_GMII:
+		__cvmx_helper_rgmii_probe(interface);
+		break;
+		/*
+		 * SPI4 can have 1-16 ports depending on the device at
+		 * the other end.
+		 */
+	case CVMX_HELPER_INTERFACE_MODE_SPI:
+		__cvmx_helper_spi_probe(interface);
+		break;
+		/*
+		 * SGMII can have 1-4 ports depending on how many are
+		 * hooked up.
+		 */
+	case CVMX_HELPER_INTERFACE_MODE_SGMII:
+	case CVMX_HELPER_INTERFACE_MODE_PICMG:
+		__cvmx_helper_sgmii_probe(interface);
+		break;
+		/* PCI target Network Packet Interface */
+	case CVMX_HELPER_INTERFACE_MODE_NPI:
+		__cvmx_helper_npi_probe(interface);
+		break;
+		/*
+		 * Special loopback only ports. These are not the same
+		 * as other ports in loopback mode.
+		 */
+	case CVMX_HELPER_INTERFACE_MODE_LOOP:
+		__cvmx_helper_loop_probe(interface);
+		break;
+	}
+
+	/* Make sure all global variables propagate to other cores */
+	CVMX_SYNCWS;
+
+	return 0;
+}
+
+/**
+ * Setup the IPD/PIP for the ports on an interface. Packet
+ * classification and tagging are set for every port on the
+ * interface. The number of ports on the interface must already
+ * have been probed.
+ *
+ * @interface: Interface to setup IPD/PIP for
+ *
+ * Returns Zero on success, negative on failure
+ */
+static int __cvmx_helper_interface_setup_ipd(int interface)
+{
+	int ipd_port = cvmx_helper_get_ipd_port(interface, 0);
+	int num_ports = interface_port_count[interface];
+
+	while (num_ports--) {
+		__cvmx_helper_port_setup_ipd(ipd_port);
+		ipd_port++;
+	}
+	return 0;
+}
+
+/**
+ * Setup global setting for IPD/PIP not related to a specific
+ * interface or port. This must be called before IPD is enabled.
+ *
+ * Returns Zero on success, negative on failure.
+ */
+static int __cvmx_helper_global_setup_ipd(void)
+{
+	/* Setup the global packet input options */
+	cvmx_ipd_config(CVMX_FPA_PACKET_POOL_SIZE / 8,
+			CVMX_HELPER_FIRST_MBUFF_SKIP / 8,
+			CVMX_HELPER_NOT_FIRST_MBUFF_SKIP / 8,
+			/* The +8 is to account for the next ptr */
+			(CVMX_HELPER_FIRST_MBUFF_SKIP + 8) / 128,
+			/* The +8 is to account for the next ptr */
+			(CVMX_HELPER_NOT_FIRST_MBUFF_SKIP + 8) / 128,
+			CVMX_FPA_WQE_POOL,
+			CVMX_IPD_OPC_MODE_STT,
+			CVMX_HELPER_ENABLE_BACK_PRESSURE);
+	return 0;
+}
+
+/**
+ * Setup the PKO for the ports on an interface. The number of
+ * queues per port and the priority of each PKO output queue
+ * is set here. PKO must be disabled when this function is called.
+ *
+ * @interface: Interface to setup PKO for
+ *
+ * Returns Zero on success, negative on failure
+ */
+static int __cvmx_helper_interface_setup_pko(int interface)
+{
+	/*
+	 * Each packet output queue has an associated priority. The
+	 * higher the priority, the more often it can send a packet. A
+	 * priority of 8 means it can send in all 8 rounds of
+	 * contention. We're going to make each queue one less than
+	 * the last.  The vector of priorities has been extended to
+	 * support CN5xxx CPUs, where up to 16 queues can be
+	 * associated to a port.  To keep backward compatibility we
+	 * don't change the initial 8 priorities and replicate them in
+	 * the second half.  With per-core PKO queues (PKO lockless
+	 * operation) all queues have the same priority.
+	 */
+	uint64_t priorities[16] =
+	    { 8, 7, 6, 5, 4, 3, 2, 1, 8, 7, 6, 5, 4, 3, 2, 1 };
+
+	/*
+	 * Setup the IPD/PIP and PKO for the ports discovered
+	 * above. Here packet classification, tagging and output
+	 * priorities are set.
+	 */
+	int ipd_port = cvmx_helper_get_ipd_port(interface, 0);
+	int num_ports = interface_port_count[interface];
+	while (num_ports--) {
+		cvmx_pko_config_port(ipd_port,
+				     cvmx_pko_get_base_queue_per_core(ipd_port,
+								      0),
+				     cvmx_pko_get_num_queues(ipd_port),
+				     priorities);
+		ipd_port++;
+	}
+	return 0;
+}
+
+/**
+ * Setup global setting for PKO not related to a specific
+ * interface or port. This must be called before PKO is enabled.
+ *
+ * Returns Zero on success, negative on failure.
+ */
+static int __cvmx_helper_global_setup_pko(void)
+{
+	/*
+	 * Disable tagwait FAU timeout. This needs to be done before
+	 * anyone might start packet output using tags.
+	 */
+	union cvmx_iob_fau_timeout fau_to;
+	fau_to.u64 = 0;
+	fau_to.s.tout_val = 0xfff;
+	fau_to.s.tout_enb = 0;
+	cvmx_write_csr(CVMX_IOB_FAU_TIMEOUT, fau_to.u64);
+
+	if (OCTEON_IS_MODEL(OCTEON_CN68XX)) {
+		union cvmx_pko_reg_min_pkt min_pkt;
+
+		min_pkt.u64 = 0;
+		min_pkt.s.size1 = 59;
+		min_pkt.s.size2 = 59;
+		min_pkt.s.size3 = 59;
+		min_pkt.s.size4 = 59;
+		min_pkt.s.size5 = 59;
+		min_pkt.s.size6 = 59;
+		min_pkt.s.size7 = 59;
+		cvmx_write_csr(CVMX_PKO_REG_MIN_PKT, min_pkt.u64);
+	}
+
+	return 0;
+}
+
+/**
+ * Setup global backpressure setting.
+ *
+ * Returns Zero on success, negative on failure
+ */
+static int __cvmx_helper_global_setup_backpressure(void)
+{
+#if CVMX_HELPER_DISABLE_RGMII_BACKPRESSURE
+	/* Disable backpressure if configured to do so */
+	/* Disable backpressure (pause frame) generation */
+	int num_interfaces = cvmx_helper_get_number_of_interfaces();
+	int interface;
+	for (interface = 0; interface < num_interfaces; interface++) {
+		switch (cvmx_helper_interface_get_mode(interface)) {
+		case CVMX_HELPER_INTERFACE_MODE_DISABLED:
+		case CVMX_HELPER_INTERFACE_MODE_PCIE:
+		case CVMX_HELPER_INTERFACE_MODE_NPI:
+		case CVMX_HELPER_INTERFACE_MODE_LOOP:
+		case CVMX_HELPER_INTERFACE_MODE_XAUI:
+			break;
+		case CVMX_HELPER_INTERFACE_MODE_RGMII:
+		case CVMX_HELPER_INTERFACE_MODE_GMII:
+		case CVMX_HELPER_INTERFACE_MODE_SPI:
+		case CVMX_HELPER_INTERFACE_MODE_SGMII:
+		case CVMX_HELPER_INTERFACE_MODE_PICMG:
+			cvmx_gmx_set_backpressure_override(interface, 0xf);
+			break;
+		}
+	}
+#endif
+
+	return 0;
+}
+
+/**
+ * Enable packet input/output from the hardware. This function is
+ * called after all internal setup is complete and IPD is enabled.
+ * After this function completes, packets will be accepted from the
+ * hardware ports. PKO should still be disabled to make sure packets
+ * aren't sent out partially setup hardware.
+ *
+ * @interface: Interface to enable
+ *
+ * Returns Zero on success, negative on failure
+ */
+static int __cvmx_helper_packet_hardware_enable(int interface)
+{
+	int result = 0;
+	switch (cvmx_helper_interface_get_mode(interface)) {
+		/* These types don't support ports to IPD/PKO */
+	case CVMX_HELPER_INTERFACE_MODE_DISABLED:
+	case CVMX_HELPER_INTERFACE_MODE_PCIE:
+		/* Nothing to do */
+		break;
+		/* XAUI is a single high speed port */
+	case CVMX_HELPER_INTERFACE_MODE_XAUI:
+		result = __cvmx_helper_xaui_enable(interface);
+		break;
+		/*
+		 * RGMII/GMII/MII are all treated about the same. Most
+		 * functions refer to these ports as RGMII
+		 */
+	case CVMX_HELPER_INTERFACE_MODE_RGMII:
+	case CVMX_HELPER_INTERFACE_MODE_GMII:
+		result = __cvmx_helper_rgmii_enable(interface);
+		break;
+		/*
+		 * SPI4 can have 1-16 ports depending on the device at
+		 * the other end
+		 */
+	case CVMX_HELPER_INTERFACE_MODE_SPI:
+		result = __cvmx_helper_spi_enable(interface);
+		break;
+		/*
+		 * SGMII can have 1-4 ports depending on how many are
+		 * hooked up
+		 */
+	case CVMX_HELPER_INTERFACE_MODE_SGMII:
+	case CVMX_HELPER_INTERFACE_MODE_PICMG:
+		result = __cvmx_helper_sgmii_enable(interface);
+		break;
+		/* PCI target Network Packet Interface */
+	case CVMX_HELPER_INTERFACE_MODE_NPI:
+		result = __cvmx_helper_npi_enable(interface);
+		break;
+		/*
+		 * Special loopback only ports. These are not the same
+		 * as other ports in loopback mode
+		 */
+	case CVMX_HELPER_INTERFACE_MODE_LOOP:
+		result = __cvmx_helper_loop_enable(interface);
+		break;
+	}
+	return result;
+}
+
+/**
+ * Function to adjust internal IPD pointer alignments
+ *
+ * Returns 0 on success
+ *	   !0 on failure
+ */
+static int __cvmx_helper_errata_fix_ipd_ptr_alignment(void)
+{
+#define FIX_IPD_FIRST_BUFF_PAYLOAD_BYTES \
+     (CVMX_FPA_PACKET_POOL_SIZE-8-CVMX_HELPER_FIRST_MBUFF_SKIP)
+#define FIX_IPD_NON_FIRST_BUFF_PAYLOAD_BYTES \
+	(CVMX_FPA_PACKET_POOL_SIZE-8-CVMX_HELPER_NOT_FIRST_MBUFF_SKIP)
+#define FIX_IPD_OUTPORT 0
+	/* Ports 0-15 are interface 0, 16-31 are interface 1 */
+#define INTERFACE(port) (port >> 4)
+#define INDEX(port) (port & 0xf)
+	uint64_t *p64;
+	union cvmx_pko_command_word0 pko_command;
+	union cvmx_buf_ptr g_buffer, pkt_buffer;
+	struct cvmx_wqe *work;
+	int size, num_segs = 0, wqe_pcnt, pkt_pcnt;
+	union cvmx_gmxx_prtx_cfg gmx_cfg;
+	int retry_cnt;
+	int retry_loop_cnt;
+	int i;
+
+	/* Save values for restore at end */
+	uint64_t prtx_cfg =
+	    cvmx_read_csr(CVMX_GMXX_PRTX_CFG
+			  (INDEX(FIX_IPD_OUTPORT), INTERFACE(FIX_IPD_OUTPORT)));
+	uint64_t tx_ptr_en =
+	    cvmx_read_csr(CVMX_ASXX_TX_PRT_EN(INTERFACE(FIX_IPD_OUTPORT)));
+	uint64_t rx_ptr_en =
+	    cvmx_read_csr(CVMX_ASXX_RX_PRT_EN(INTERFACE(FIX_IPD_OUTPORT)));
+	uint64_t rxx_jabber =
+	    cvmx_read_csr(CVMX_GMXX_RXX_JABBER
+			  (INDEX(FIX_IPD_OUTPORT), INTERFACE(FIX_IPD_OUTPORT)));
+	uint64_t frame_max =
+	    cvmx_read_csr(CVMX_GMXX_RXX_FRM_MAX
+			  (INDEX(FIX_IPD_OUTPORT), INTERFACE(FIX_IPD_OUTPORT)));
+
+	/* Configure port to gig FDX as required for loopback mode */
+	cvmx_helper_rgmii_internal_loopback(FIX_IPD_OUTPORT);
+
+	/*
+	 * Disable reception on all ports so if traffic is present it
+	 * will not interfere.
+	 */
+	cvmx_write_csr(CVMX_ASXX_RX_PRT_EN(INTERFACE(FIX_IPD_OUTPORT)), 0);
+
+	__delay(100000000ull);
+
+	for (retry_loop_cnt = 0; retry_loop_cnt < 10; retry_loop_cnt++) {
+		retry_cnt = 100000;
+		wqe_pcnt = cvmx_read_csr(CVMX_IPD_PTR_COUNT);
+		pkt_pcnt = (wqe_pcnt >> 7) & 0x7f;
+		wqe_pcnt &= 0x7f;
+
+		num_segs = (2 + pkt_pcnt - wqe_pcnt) & 3;
+
+		if (num_segs == 0)
+			goto fix_ipd_exit;
+
+		num_segs += 1;
+
+		size =
+		    FIX_IPD_FIRST_BUFF_PAYLOAD_BYTES +
+		    ((num_segs - 1) * FIX_IPD_NON_FIRST_BUFF_PAYLOAD_BYTES) -
+		    (FIX_IPD_NON_FIRST_BUFF_PAYLOAD_BYTES / 2);
+
+		cvmx_write_csr(CVMX_ASXX_PRT_LOOP(INTERFACE(FIX_IPD_OUTPORT)),
+			       1 << INDEX(FIX_IPD_OUTPORT));
+		CVMX_SYNC;
+
+		g_buffer.u64 = 0;
+		g_buffer.s.addr =
+		    cvmx_ptr_to_phys(cvmx_fpa_alloc(CVMX_FPA_WQE_POOL));
+		if (g_buffer.s.addr == 0) {
+			cvmx_dprintf("WARNING: FIX_IPD_PTR_ALIGNMENT "
+				     "buffer allocation failure.\n");
+			goto fix_ipd_exit;
+		}
+
+		g_buffer.s.pool = CVMX_FPA_WQE_POOL;
+		g_buffer.s.size = num_segs;
+
+		pkt_buffer.u64 = 0;
+		pkt_buffer.s.addr =
+		    cvmx_ptr_to_phys(cvmx_fpa_alloc(CVMX_FPA_PACKET_POOL));
+		if (pkt_buffer.s.addr == 0) {
+			cvmx_dprintf("WARNING: FIX_IPD_PTR_ALIGNMENT "
+				     "buffer allocation failure.\n");
+			goto fix_ipd_exit;
+		}
+		pkt_buffer.s.i = 1;
+		pkt_buffer.s.pool = CVMX_FPA_PACKET_POOL;
+		pkt_buffer.s.size = FIX_IPD_FIRST_BUFF_PAYLOAD_BYTES;
+
+		p64 = (uint64_t *) cvmx_phys_to_ptr(pkt_buffer.s.addr);
+		p64[0] = 0xffffffffffff0000ull;
+		p64[1] = 0x08004510ull;
+		p64[2] = ((uint64_t) (size - 14) << 48) | 0x5ae740004000ull;
+		p64[3] = 0x3a5fc0a81073c0a8ull;
+
+		for (i = 0; i < num_segs; i++) {
+			if (i > 0)
+				pkt_buffer.s.size =
+				    FIX_IPD_NON_FIRST_BUFF_PAYLOAD_BYTES;
+
+			if (i == (num_segs - 1))
+				pkt_buffer.s.i = 0;
+
+			*(uint64_t *) cvmx_phys_to_ptr(g_buffer.s.addr +
+						       8 * i) = pkt_buffer.u64;
+		}
+
+		/* Build the PKO command */
+		pko_command.u64 = 0;
+		pko_command.s.segs = num_segs;
+		pko_command.s.total_bytes = size;
+		pko_command.s.dontfree = 0;
+		pko_command.s.gather = 1;
+
+		gmx_cfg.u64 =
+		    cvmx_read_csr(CVMX_GMXX_PRTX_CFG
+				  (INDEX(FIX_IPD_OUTPORT),
+				   INTERFACE(FIX_IPD_OUTPORT)));
+		gmx_cfg.s.en = 1;
+		cvmx_write_csr(CVMX_GMXX_PRTX_CFG
+			       (INDEX(FIX_IPD_OUTPORT),
+				INTERFACE(FIX_IPD_OUTPORT)), gmx_cfg.u64);
+		cvmx_write_csr(CVMX_ASXX_TX_PRT_EN(INTERFACE(FIX_IPD_OUTPORT)),
+			       1 << INDEX(FIX_IPD_OUTPORT));
+		cvmx_write_csr(CVMX_ASXX_RX_PRT_EN(INTERFACE(FIX_IPD_OUTPORT)),
+			       1 << INDEX(FIX_IPD_OUTPORT));
+
+		cvmx_write_csr(CVMX_GMXX_RXX_JABBER
+			       (INDEX(FIX_IPD_OUTPORT),
+				INTERFACE(FIX_IPD_OUTPORT)), 65392 - 14 - 4);
+		cvmx_write_csr(CVMX_GMXX_RXX_FRM_MAX
+			       (INDEX(FIX_IPD_OUTPORT),
+				INTERFACE(FIX_IPD_OUTPORT)), 65392 - 14 - 4);
+
+		cvmx_pko_send_packet_prepare(FIX_IPD_OUTPORT,
+					     cvmx_pko_get_base_queue
+					     (FIX_IPD_OUTPORT),
+					     CVMX_PKO_LOCK_CMD_QUEUE);
+		cvmx_pko_send_packet_finish(FIX_IPD_OUTPORT,
+					    cvmx_pko_get_base_queue
+					    (FIX_IPD_OUTPORT), pko_command,
+					    g_buffer, CVMX_PKO_LOCK_CMD_QUEUE);
+
+		CVMX_SYNC;
+
+		do {
+			work = cvmx_pow_work_request_sync(CVMX_POW_WAIT);
+			retry_cnt--;
+		} while ((work == NULL) && (retry_cnt > 0));
+
+		if (!retry_cnt)
+			cvmx_dprintf("WARNING: FIX_IPD_PTR_ALIGNMENT "
+				     "get_work() timeout occurred.\n");
+
+		/* Free packet */
+		if (work)
+			cvmx_helper_free_packet_data(work);
+	}
+
+fix_ipd_exit:
+
+	/* Return CSR configs to saved values */
+	cvmx_write_csr(CVMX_GMXX_PRTX_CFG
+		       (INDEX(FIX_IPD_OUTPORT), INTERFACE(FIX_IPD_OUTPORT)),
+		       prtx_cfg);
+	cvmx_write_csr(CVMX_ASXX_TX_PRT_EN(INTERFACE(FIX_IPD_OUTPORT)),
+		       tx_ptr_en);
+	cvmx_write_csr(CVMX_ASXX_RX_PRT_EN(INTERFACE(FIX_IPD_OUTPORT)),
+		       rx_ptr_en);
+	cvmx_write_csr(CVMX_GMXX_RXX_JABBER
+		       (INDEX(FIX_IPD_OUTPORT), INTERFACE(FIX_IPD_OUTPORT)),
+		       rxx_jabber);
+	cvmx_write_csr(CVMX_GMXX_RXX_FRM_MAX
+		       (INDEX(FIX_IPD_OUTPORT), INTERFACE(FIX_IPD_OUTPORT)),
+		       frame_max);
+	cvmx_write_csr(CVMX_ASXX_PRT_LOOP(INTERFACE(FIX_IPD_OUTPORT)), 0);
+
+	CVMX_SYNC;
+	if (num_segs)
+		cvmx_dprintf("WARNING: FIX_IPD_PTR_ALIGNMENT failed.\n");
+
+	return !!num_segs;
+
+}
+
+/**
+ * Called after all internal packet IO paths are setup. This
+ * function enables IPD/PIP and begins packet input and output.
+ *
+ * Returns Zero on success, negative on failure
+ */
+int cvmx_helper_ipd_and_packet_input_enable(void)
+{
+	int num_interfaces;
+	int interface;
+
+	/* Enable IPD */
+	cvmx_ipd_enable();
+
+	/*
+	 * Time to enable hardware ports packet input and output. Note
+	 * that at this point IPD/PIP must be fully functional and PKO
+	 * must be disabled
+	 */
+	num_interfaces = cvmx_helper_get_number_of_interfaces();
+	for (interface = 0; interface < num_interfaces; interface++) {
+		if (cvmx_helper_ports_on_interface(interface) > 0)
+			__cvmx_helper_packet_hardware_enable(interface);
+	}
+
+	/* Finally enable PKO now that the entire path is up and running */
+	cvmx_pko_enable();
+
+	if ((OCTEON_IS_MODEL(OCTEON_CN31XX_PASS1)
+	     || OCTEON_IS_MODEL(OCTEON_CN30XX_PASS1))
+	    && (cvmx_sysinfo_get()->board_type != CVMX_BOARD_TYPE_SIM))
+		__cvmx_helper_errata_fix_ipd_ptr_alignment();
+	return 0;
+}
+EXPORT_SYMBOL_GPL(cvmx_helper_ipd_and_packet_input_enable);
+
+/**
+ * Initialize the PIP, IPD, and PKO hardware to support
+ * simple priority based queues for the ethernet ports. Each
+ * port is configured with a number of priority queues based
+ * on CVMX_PKO_QUEUES_PER_PORT_* where each queue is lower
+ * priority than the previous.
+ *
+ * Returns Zero on success, non-zero on failure
+ */
+int cvmx_helper_initialize_packet_io_global(void)
+{
+	int result = 0;
+	int interface;
+	union cvmx_l2c_cfg l2c_cfg;
+	const int num_interfaces = cvmx_helper_get_number_of_interfaces();
+
+	/*
+	 * CN52XX pass 1: Due to a bug in 2nd order CDR, it needs to
+	 * be disabled.
+	 */
+	if (OCTEON_IS_MODEL(OCTEON_CN52XX_PASS1_0))
+		__cvmx_helper_errata_qlm_disable_2nd_order_cdr(1);
+
+	/*
+	 * Tell L2 to give the IOB statically higher priority compared
+	 * to the cores. This avoids conditions where IO blocks might
+	 * be starved under very high L2 loads.
+	 */
+	l2c_cfg.u64 = cvmx_read_csr(CVMX_L2C_CFG);
+	l2c_cfg.s.lrf_arb_mode = 0;
+	l2c_cfg.s.rfb_arb_mode = 0;
+	cvmx_write_csr(CVMX_L2C_CFG, l2c_cfg.u64);
+
+	cvmx_pko_initialize_global();
+	for (interface = 0; interface < num_interfaces; interface++) {
+		result |= cvmx_helper_interface_probe(interface);
+		if (cvmx_helper_ports_on_interface(interface) > 0)
+			cvmx_dprintf("Interface %d has %d ports (%s)\n",
+				     interface,
+				     cvmx_helper_ports_on_interface(interface),
+				     cvmx_helper_interface_mode_to_string
+				     (cvmx_helper_interface_get_mode
+				      (interface)));
+		result |= __cvmx_helper_interface_setup_ipd(interface);
+		result |= __cvmx_helper_interface_setup_pko(interface);
+	}
+
+	result |= __cvmx_helper_global_setup_ipd();
+	result |= __cvmx_helper_global_setup_pko();
+
+	/* Enable any flow control and backpressure */
+	result |= __cvmx_helper_global_setup_backpressure();
+
+#if CVMX_HELPER_ENABLE_IPD
+	result |= cvmx_helper_ipd_and_packet_input_enable();
+#endif
+	return result;
+}
+EXPORT_SYMBOL_GPL(cvmx_helper_initialize_packet_io_global);
+
+/**
+ * Return the link state of an IPD/PKO port as returned by
+ * auto negotiation. The result of this function may not match
+ * Octeon's link config if auto negotiation has changed since
+ * the last call to cvmx_helper_link_set().
+ *
+ * @ipd_port: IPD/PKO port to query
+ *
+ * Returns Link state
+ */
+union cvmx_helper_link_info cvmx_helper_link_get(int ipd_port)
+{
+	union cvmx_helper_link_info result;
+	int interface = cvmx_helper_get_interface_num(ipd_port);
+	int index = cvmx_helper_get_interface_index_num(ipd_port);
+
+	/* The default result will be a down link unless the code below
+	   changes it */
+	result.u64 = 0;
+
+	if (index >= cvmx_helper_ports_on_interface(interface))
+		return result;
+
+	switch (cvmx_helper_interface_get_mode(interface)) {
+	case CVMX_HELPER_INTERFACE_MODE_DISABLED:
+	case CVMX_HELPER_INTERFACE_MODE_PCIE:
+		/* Network links are not supported */
+		break;
+	case CVMX_HELPER_INTERFACE_MODE_XAUI:
+		result = __cvmx_helper_xaui_link_get(ipd_port);
+		break;
+	case CVMX_HELPER_INTERFACE_MODE_GMII:
+		if (index == 0)
+			result = __cvmx_helper_rgmii_link_get(ipd_port);
+		else {
+			WARN_ONCE(1, "Using deprecated link status - please update your DT");
+			result.s.full_duplex = 1;
+			result.s.link_up = 1;
+			result.s.speed = 1000;
+		}
+		break;
+	case CVMX_HELPER_INTERFACE_MODE_RGMII:
+		result = __cvmx_helper_rgmii_link_get(ipd_port);
+		break;
+	case CVMX_HELPER_INTERFACE_MODE_SPI:
+		result = __cvmx_helper_spi_link_get(ipd_port);
+		break;
+	case CVMX_HELPER_INTERFACE_MODE_SGMII:
+	case CVMX_HELPER_INTERFACE_MODE_PICMG:
+		result = __cvmx_helper_sgmii_link_get(ipd_port);
+		break;
+	case CVMX_HELPER_INTERFACE_MODE_NPI:
+	case CVMX_HELPER_INTERFACE_MODE_LOOP:
+		/* Network links are not supported */
+		break;
+	}
+	return result;
+}
+EXPORT_SYMBOL_GPL(cvmx_helper_link_get);
+
+/**
+ * Configure an IPD/PKO port for the specified link state. This
+ * function does not influence auto negotiation at the PHY level.
+ * The passed link state must always match the link state returned
+ * by cvmx_helper_link_get().
+ *
+ * @ipd_port:  IPD/PKO port to configure
+ * @link_info: The new link state
+ *
+ * Returns Zero on success, negative on failure
+ */
+int cvmx_helper_link_set(int ipd_port, union cvmx_helper_link_info link_info)
+{
+	int result = -1;
+	int interface = cvmx_helper_get_interface_num(ipd_port);
+	int index = cvmx_helper_get_interface_index_num(ipd_port);
+
+	if (index >= cvmx_helper_ports_on_interface(interface))
+		return -1;
+
+	switch (cvmx_helper_interface_get_mode(interface)) {
+	case CVMX_HELPER_INTERFACE_MODE_DISABLED:
+	case CVMX_HELPER_INTERFACE_MODE_PCIE:
+		break;
+	case CVMX_HELPER_INTERFACE_MODE_XAUI:
+		result = __cvmx_helper_xaui_link_set(ipd_port, link_info);
+		break;
+		/*
+		 * RGMII/GMII/MII are all treated about the same. Most
+		 * functions refer to these ports as RGMII.
+		 */
+	case CVMX_HELPER_INTERFACE_MODE_RGMII:
+	case CVMX_HELPER_INTERFACE_MODE_GMII:
+		result = __cvmx_helper_rgmii_link_set(ipd_port, link_info);
+		break;
+	case CVMX_HELPER_INTERFACE_MODE_SPI:
+		result = __cvmx_helper_spi_link_set(ipd_port, link_info);
+		break;
+	case CVMX_HELPER_INTERFACE_MODE_SGMII:
+	case CVMX_HELPER_INTERFACE_MODE_PICMG:
+		result = __cvmx_helper_sgmii_link_set(ipd_port, link_info);
+		break;
+	case CVMX_HELPER_INTERFACE_MODE_NPI:
+	case CVMX_HELPER_INTERFACE_MODE_LOOP:
+		break;
+	}
+	return result;
+}
+EXPORT_SYMBOL_GPL(cvmx_helper_link_set);
diff --git a/arch/mips/cavium-octeon/executive/cvmx-interrupt-decodes.c b/arch/mips/cavium-octeon/executive/cvmx-interrupt-decodes.c
new file mode 100644
index 000000000..67d6da21d
--- /dev/null
+++ b/arch/mips/cavium-octeon/executive/cvmx-interrupt-decodes.c
@@ -0,0 +1,378 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2009 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ *
+ * Automatically generated functions useful for enabling
+ * and decoding RSL_INT_BLOCKS interrupts.
+ *
+ */
+
+#include <asm/octeon/octeon.h>
+
+#include <asm/octeon/cvmx-gmxx-defs.h>
+#include <asm/octeon/cvmx-pcsx-defs.h>
+#include <asm/octeon/cvmx-pcsxx-defs.h>
+#include <asm/octeon/cvmx-spxx-defs.h>
+#include <asm/octeon/cvmx-stxx-defs.h>
+
+#ifndef PRINT_ERROR
+#define PRINT_ERROR(format, ...)
+#endif
+
+
+/**
+ * __cvmx_interrupt_gmxx_rxx_int_en_enable - enable all interrupt bits in cvmx_gmxx_rxx_int_en_t
+ * @index: interrupt register offset
+ * @block: interrupt register block_id
+ */
+void __cvmx_interrupt_gmxx_rxx_int_en_enable(int index, int block)
+{
+	union cvmx_gmxx_rxx_int_en gmx_rx_int_en;
+	cvmx_write_csr(CVMX_GMXX_RXX_INT_REG(index, block),
+		       cvmx_read_csr(CVMX_GMXX_RXX_INT_REG(index, block)));
+	gmx_rx_int_en.u64 = 0;
+	if (OCTEON_IS_MODEL(OCTEON_CN56XX)) {
+		/* Skipping gmx_rx_int_en.s.reserved_29_63 */
+		gmx_rx_int_en.s.hg2cc = 1;
+		gmx_rx_int_en.s.hg2fld = 1;
+		gmx_rx_int_en.s.undat = 1;
+		gmx_rx_int_en.s.uneop = 1;
+		gmx_rx_int_en.s.unsop = 1;
+		gmx_rx_int_en.s.bad_term = 1;
+		gmx_rx_int_en.s.bad_seq = 1;
+		gmx_rx_int_en.s.rem_fault = 1;
+		gmx_rx_int_en.s.loc_fault = 1;
+		gmx_rx_int_en.s.pause_drp = 1;
+		/* Skipping gmx_rx_int_en.s.reserved_16_18 */
+		/*gmx_rx_int_en.s.ifgerr = 1; */
+		/*gmx_rx_int_en.s.coldet = 1; // Collision detect */
+		/*gmx_rx_int_en.s.falerr = 1; // False carrier error or extend error after slottime */
+		/*gmx_rx_int_en.s.rsverr = 1; // RGMII reserved opcodes */
+		/*gmx_rx_int_en.s.pcterr = 1; // Bad Preamble / Protocol */
+		gmx_rx_int_en.s.ovrerr = 1;
+		/* Skipping gmx_rx_int_en.s.reserved_9_9 */
+		gmx_rx_int_en.s.skperr = 1;
+		gmx_rx_int_en.s.rcverr = 1;
+		/* Skipping gmx_rx_int_en.s.reserved_5_6 */
+		/*gmx_rx_int_en.s.fcserr = 1; // FCS errors are handled when we get work */
+		gmx_rx_int_en.s.jabber = 1;
+		/* Skipping gmx_rx_int_en.s.reserved_2_2 */
+		gmx_rx_int_en.s.carext = 1;
+		/* Skipping gmx_rx_int_en.s.reserved_0_0 */
+	}
+	if (OCTEON_IS_MODEL(OCTEON_CN30XX)) {
+		/* Skipping gmx_rx_int_en.s.reserved_19_63 */
+		/*gmx_rx_int_en.s.phy_dupx = 1; */
+		/*gmx_rx_int_en.s.phy_spd = 1; */
+		/*gmx_rx_int_en.s.phy_link = 1; */
+		/*gmx_rx_int_en.s.ifgerr = 1; */
+		/*gmx_rx_int_en.s.coldet = 1; // Collision detect */
+		/*gmx_rx_int_en.s.falerr = 1; // False carrier error or extend error after slottime */
+		/*gmx_rx_int_en.s.rsverr = 1; // RGMII reserved opcodes */
+		/*gmx_rx_int_en.s.pcterr = 1; // Bad Preamble / Protocol */
+		gmx_rx_int_en.s.ovrerr = 1;
+		gmx_rx_int_en.s.niberr = 1;
+		gmx_rx_int_en.s.skperr = 1;
+		gmx_rx_int_en.s.rcverr = 1;
+		/*gmx_rx_int_en.s.lenerr = 1; // Length errors are handled when we get work */
+		gmx_rx_int_en.s.alnerr = 1;
+		/*gmx_rx_int_en.s.fcserr = 1; // FCS errors are handled when we get work */
+		gmx_rx_int_en.s.jabber = 1;
+		gmx_rx_int_en.s.maxerr = 1;
+		gmx_rx_int_en.s.carext = 1;
+		gmx_rx_int_en.s.minerr = 1;
+	}
+	if (OCTEON_IS_MODEL(OCTEON_CN50XX)) {
+		/* Skipping gmx_rx_int_en.s.reserved_20_63 */
+		gmx_rx_int_en.s.pause_drp = 1;
+		/*gmx_rx_int_en.s.phy_dupx = 1; */
+		/*gmx_rx_int_en.s.phy_spd = 1; */
+		/*gmx_rx_int_en.s.phy_link = 1; */
+		/*gmx_rx_int_en.s.ifgerr = 1; */
+		/*gmx_rx_int_en.s.coldet = 1; // Collision detect */
+		/*gmx_rx_int_en.s.falerr = 1; // False carrier error or extend error after slottime */
+		/*gmx_rx_int_en.s.rsverr = 1; // RGMII reserved opcodes */
+		/*gmx_rx_int_en.s.pcterr = 1; // Bad Preamble / Protocol */
+		gmx_rx_int_en.s.ovrerr = 1;
+		gmx_rx_int_en.s.niberr = 1;
+		gmx_rx_int_en.s.skperr = 1;
+		gmx_rx_int_en.s.rcverr = 1;
+		/* Skipping gmx_rx_int_en.s.reserved_6_6 */
+		gmx_rx_int_en.s.alnerr = 1;
+		/*gmx_rx_int_en.s.fcserr = 1; // FCS errors are handled when we get work */
+		gmx_rx_int_en.s.jabber = 1;
+		/* Skipping gmx_rx_int_en.s.reserved_2_2 */
+		gmx_rx_int_en.s.carext = 1;
+		/* Skipping gmx_rx_int_en.s.reserved_0_0 */
+	}
+	if (OCTEON_IS_MODEL(OCTEON_CN38XX)) {
+		/* Skipping gmx_rx_int_en.s.reserved_19_63 */
+		/*gmx_rx_int_en.s.phy_dupx = 1; */
+		/*gmx_rx_int_en.s.phy_spd = 1; */
+		/*gmx_rx_int_en.s.phy_link = 1; */
+		/*gmx_rx_int_en.s.ifgerr = 1; */
+		/*gmx_rx_int_en.s.coldet = 1; // Collision detect */
+		/*gmx_rx_int_en.s.falerr = 1; // False carrier error or extend error after slottime */
+		/*gmx_rx_int_en.s.rsverr = 1; // RGMII reserved opcodes */
+		/*gmx_rx_int_en.s.pcterr = 1; // Bad Preamble / Protocol */
+		gmx_rx_int_en.s.ovrerr = 1;
+		gmx_rx_int_en.s.niberr = 1;
+		gmx_rx_int_en.s.skperr = 1;
+		gmx_rx_int_en.s.rcverr = 1;
+		/*gmx_rx_int_en.s.lenerr = 1; // Length errors are handled when we get work */
+		gmx_rx_int_en.s.alnerr = 1;
+		/*gmx_rx_int_en.s.fcserr = 1; // FCS errors are handled when we get work */
+		gmx_rx_int_en.s.jabber = 1;
+		gmx_rx_int_en.s.maxerr = 1;
+		gmx_rx_int_en.s.carext = 1;
+		gmx_rx_int_en.s.minerr = 1;
+	}
+	if (OCTEON_IS_MODEL(OCTEON_CN31XX)) {
+		/* Skipping gmx_rx_int_en.s.reserved_19_63 */
+		/*gmx_rx_int_en.s.phy_dupx = 1; */
+		/*gmx_rx_int_en.s.phy_spd = 1; */
+		/*gmx_rx_int_en.s.phy_link = 1; */
+		/*gmx_rx_int_en.s.ifgerr = 1; */
+		/*gmx_rx_int_en.s.coldet = 1; // Collision detect */
+		/*gmx_rx_int_en.s.falerr = 1; // False carrier error or extend error after slottime */
+		/*gmx_rx_int_en.s.rsverr = 1; // RGMII reserved opcodes */
+		/*gmx_rx_int_en.s.pcterr = 1; // Bad Preamble / Protocol */
+		gmx_rx_int_en.s.ovrerr = 1;
+		gmx_rx_int_en.s.niberr = 1;
+		gmx_rx_int_en.s.skperr = 1;
+		gmx_rx_int_en.s.rcverr = 1;
+		/*gmx_rx_int_en.s.lenerr = 1; // Length errors are handled when we get work */
+		gmx_rx_int_en.s.alnerr = 1;
+		/*gmx_rx_int_en.s.fcserr = 1; // FCS errors are handled when we get work */
+		gmx_rx_int_en.s.jabber = 1;
+		gmx_rx_int_en.s.maxerr = 1;
+		gmx_rx_int_en.s.carext = 1;
+		gmx_rx_int_en.s.minerr = 1;
+	}
+	if (OCTEON_IS_MODEL(OCTEON_CN58XX)) {
+		/* Skipping gmx_rx_int_en.s.reserved_20_63 */
+		gmx_rx_int_en.s.pause_drp = 1;
+		/*gmx_rx_int_en.s.phy_dupx = 1; */
+		/*gmx_rx_int_en.s.phy_spd = 1; */
+		/*gmx_rx_int_en.s.phy_link = 1; */
+		/*gmx_rx_int_en.s.ifgerr = 1; */
+		/*gmx_rx_int_en.s.coldet = 1; // Collision detect */
+		/*gmx_rx_int_en.s.falerr = 1; // False carrier error or extend error after slottime */
+		/*gmx_rx_int_en.s.rsverr = 1; // RGMII reserved opcodes */
+		/*gmx_rx_int_en.s.pcterr = 1; // Bad Preamble / Protocol */
+		gmx_rx_int_en.s.ovrerr = 1;
+		gmx_rx_int_en.s.niberr = 1;
+		gmx_rx_int_en.s.skperr = 1;
+		gmx_rx_int_en.s.rcverr = 1;
+		/*gmx_rx_int_en.s.lenerr = 1; // Length errors are handled when we get work */
+		gmx_rx_int_en.s.alnerr = 1;
+		/*gmx_rx_int_en.s.fcserr = 1; // FCS errors are handled when we get work */
+		gmx_rx_int_en.s.jabber = 1;
+		gmx_rx_int_en.s.maxerr = 1;
+		gmx_rx_int_en.s.carext = 1;
+		gmx_rx_int_en.s.minerr = 1;
+	}
+	if (OCTEON_IS_MODEL(OCTEON_CN52XX)) {
+		/* Skipping gmx_rx_int_en.s.reserved_29_63 */
+		gmx_rx_int_en.s.hg2cc = 1;
+		gmx_rx_int_en.s.hg2fld = 1;
+		gmx_rx_int_en.s.undat = 1;
+		gmx_rx_int_en.s.uneop = 1;
+		gmx_rx_int_en.s.unsop = 1;
+		gmx_rx_int_en.s.bad_term = 1;
+		gmx_rx_int_en.s.bad_seq = 0;
+		gmx_rx_int_en.s.rem_fault = 1;
+		gmx_rx_int_en.s.loc_fault = 0;
+		gmx_rx_int_en.s.pause_drp = 1;
+		/* Skipping gmx_rx_int_en.s.reserved_16_18 */
+		/*gmx_rx_int_en.s.ifgerr = 1; */
+		/*gmx_rx_int_en.s.coldet = 1; // Collision detect */
+		/*gmx_rx_int_en.s.falerr = 1; // False carrier error or extend error after slottime */
+		/*gmx_rx_int_en.s.rsverr = 1; // RGMII reserved opcodes */
+		/*gmx_rx_int_en.s.pcterr = 1; // Bad Preamble / Protocol */
+		gmx_rx_int_en.s.ovrerr = 1;
+		/* Skipping gmx_rx_int_en.s.reserved_9_9 */
+		gmx_rx_int_en.s.skperr = 1;
+		gmx_rx_int_en.s.rcverr = 1;
+		/* Skipping gmx_rx_int_en.s.reserved_5_6 */
+		/*gmx_rx_int_en.s.fcserr = 1; // FCS errors are handled when we get work */
+		gmx_rx_int_en.s.jabber = 1;
+		/* Skipping gmx_rx_int_en.s.reserved_2_2 */
+		gmx_rx_int_en.s.carext = 1;
+		/* Skipping gmx_rx_int_en.s.reserved_0_0 */
+	}
+	cvmx_write_csr(CVMX_GMXX_RXX_INT_EN(index, block), gmx_rx_int_en.u64);
+}
+/**
+ * __cvmx_interrupt_pcsx_intx_en_reg_enable - enable all interrupt bits in cvmx_pcsx_intx_en_reg_t
+ * @index: interrupt register offset
+ * @block: interrupt register block_id
+ */
+void __cvmx_interrupt_pcsx_intx_en_reg_enable(int index, int block)
+{
+	union cvmx_pcsx_intx_en_reg pcs_int_en_reg;
+	cvmx_write_csr(CVMX_PCSX_INTX_REG(index, block),
+		       cvmx_read_csr(CVMX_PCSX_INTX_REG(index, block)));
+	pcs_int_en_reg.u64 = 0;
+	if (OCTEON_IS_MODEL(OCTEON_CN56XX)) {
+		/* Skipping pcs_int_en_reg.s.reserved_12_63 */
+		/*pcs_int_en_reg.s.dup = 1; // This happens during normal operation */
+		pcs_int_en_reg.s.sync_bad_en = 1;
+		pcs_int_en_reg.s.an_bad_en = 1;
+		pcs_int_en_reg.s.rxlock_en = 1;
+		pcs_int_en_reg.s.rxbad_en = 1;
+		/*pcs_int_en_reg.s.rxerr_en = 1; // This happens during normal operation */
+		pcs_int_en_reg.s.txbad_en = 1;
+		pcs_int_en_reg.s.txfifo_en = 1;
+		pcs_int_en_reg.s.txfifu_en = 1;
+		pcs_int_en_reg.s.an_err_en = 1;
+		/*pcs_int_en_reg.s.xmit_en = 1; // This happens during normal operation */
+		/*pcs_int_en_reg.s.lnkspd_en = 1; // This happens during normal operation */
+	}
+	if (OCTEON_IS_MODEL(OCTEON_CN52XX)) {
+		/* Skipping pcs_int_en_reg.s.reserved_12_63 */
+		/*pcs_int_en_reg.s.dup = 1; // This happens during normal operation */
+		pcs_int_en_reg.s.sync_bad_en = 1;
+		pcs_int_en_reg.s.an_bad_en = 1;
+		pcs_int_en_reg.s.rxlock_en = 1;
+		pcs_int_en_reg.s.rxbad_en = 1;
+		/*pcs_int_en_reg.s.rxerr_en = 1; // This happens during normal operation */
+		pcs_int_en_reg.s.txbad_en = 1;
+		pcs_int_en_reg.s.txfifo_en = 1;
+		pcs_int_en_reg.s.txfifu_en = 1;
+		pcs_int_en_reg.s.an_err_en = 1;
+		/*pcs_int_en_reg.s.xmit_en = 1; // This happens during normal operation */
+		/*pcs_int_en_reg.s.lnkspd_en = 1; // This happens during normal operation */
+	}
+	cvmx_write_csr(CVMX_PCSX_INTX_EN_REG(index, block), pcs_int_en_reg.u64);
+}
+/**
+ * __cvmx_interrupt_pcsxx_int_en_reg_enable - enable all interrupt bits in cvmx_pcsxx_int_en_reg_t
+ * @index: interrupt register block_id
+ */
+void __cvmx_interrupt_pcsxx_int_en_reg_enable(int index)
+{
+	union cvmx_pcsxx_int_en_reg pcsx_int_en_reg;
+	cvmx_write_csr(CVMX_PCSXX_INT_REG(index),
+		       cvmx_read_csr(CVMX_PCSXX_INT_REG(index)));
+	pcsx_int_en_reg.u64 = 0;
+	if (OCTEON_IS_MODEL(OCTEON_CN56XX)) {
+		/* Skipping pcsx_int_en_reg.s.reserved_6_63 */
+		pcsx_int_en_reg.s.algnlos_en = 1;
+		pcsx_int_en_reg.s.synlos_en = 1;
+		pcsx_int_en_reg.s.bitlckls_en = 1;
+		pcsx_int_en_reg.s.rxsynbad_en = 1;
+		pcsx_int_en_reg.s.rxbad_en = 1;
+		pcsx_int_en_reg.s.txflt_en = 1;
+	}
+	if (OCTEON_IS_MODEL(OCTEON_CN52XX)) {
+		/* Skipping pcsx_int_en_reg.s.reserved_6_63 */
+		pcsx_int_en_reg.s.algnlos_en = 1;
+		pcsx_int_en_reg.s.synlos_en = 1;
+		pcsx_int_en_reg.s.bitlckls_en = 0;	/* Happens if XAUI module is not installed */
+		pcsx_int_en_reg.s.rxsynbad_en = 1;
+		pcsx_int_en_reg.s.rxbad_en = 1;
+		pcsx_int_en_reg.s.txflt_en = 1;
+	}
+	cvmx_write_csr(CVMX_PCSXX_INT_EN_REG(index), pcsx_int_en_reg.u64);
+}
+
+/**
+ * __cvmx_interrupt_spxx_int_msk_enable - enable all interrupt bits in cvmx_spxx_int_msk_t
+ * @index: interrupt register block_id
+ */
+void __cvmx_interrupt_spxx_int_msk_enable(int index)
+{
+	union cvmx_spxx_int_msk spx_int_msk;
+	cvmx_write_csr(CVMX_SPXX_INT_REG(index),
+		       cvmx_read_csr(CVMX_SPXX_INT_REG(index)));
+	spx_int_msk.u64 = 0;
+	if (OCTEON_IS_MODEL(OCTEON_CN38XX)) {
+		/* Skipping spx_int_msk.s.reserved_12_63 */
+		spx_int_msk.s.calerr = 1;
+		spx_int_msk.s.syncerr = 1;
+		spx_int_msk.s.diperr = 1;
+		spx_int_msk.s.tpaovr = 1;
+		spx_int_msk.s.rsverr = 1;
+		spx_int_msk.s.drwnng = 1;
+		spx_int_msk.s.clserr = 1;
+		spx_int_msk.s.spiovr = 1;
+		/* Skipping spx_int_msk.s.reserved_2_3 */
+		spx_int_msk.s.abnorm = 1;
+		spx_int_msk.s.prtnxa = 1;
+	}
+	if (OCTEON_IS_MODEL(OCTEON_CN58XX)) {
+		/* Skipping spx_int_msk.s.reserved_12_63 */
+		spx_int_msk.s.calerr = 1;
+		spx_int_msk.s.syncerr = 1;
+		spx_int_msk.s.diperr = 1;
+		spx_int_msk.s.tpaovr = 1;
+		spx_int_msk.s.rsverr = 1;
+		spx_int_msk.s.drwnng = 1;
+		spx_int_msk.s.clserr = 1;
+		spx_int_msk.s.spiovr = 1;
+		/* Skipping spx_int_msk.s.reserved_2_3 */
+		spx_int_msk.s.abnorm = 1;
+		spx_int_msk.s.prtnxa = 1;
+	}
+	cvmx_write_csr(CVMX_SPXX_INT_MSK(index), spx_int_msk.u64);
+}
+/**
+ * __cvmx_interrupt_stxx_int_msk_enable - enable all interrupt bits in cvmx_stxx_int_msk_t
+ * @index: interrupt register block_id
+ */
+void __cvmx_interrupt_stxx_int_msk_enable(int index)
+{
+	union cvmx_stxx_int_msk stx_int_msk;
+	cvmx_write_csr(CVMX_STXX_INT_REG(index),
+		       cvmx_read_csr(CVMX_STXX_INT_REG(index)));
+	stx_int_msk.u64 = 0;
+	if (OCTEON_IS_MODEL(OCTEON_CN38XX)) {
+		/* Skipping stx_int_msk.s.reserved_8_63 */
+		stx_int_msk.s.frmerr = 1;
+		stx_int_msk.s.unxfrm = 1;
+		stx_int_msk.s.nosync = 1;
+		stx_int_msk.s.diperr = 1;
+		stx_int_msk.s.datovr = 1;
+		stx_int_msk.s.ovrbst = 1;
+		stx_int_msk.s.calpar1 = 1;
+		stx_int_msk.s.calpar0 = 1;
+	}
+	if (OCTEON_IS_MODEL(OCTEON_CN58XX)) {
+		/* Skipping stx_int_msk.s.reserved_8_63 */
+		stx_int_msk.s.frmerr = 1;
+		stx_int_msk.s.unxfrm = 1;
+		stx_int_msk.s.nosync = 1;
+		stx_int_msk.s.diperr = 1;
+		stx_int_msk.s.datovr = 1;
+		stx_int_msk.s.ovrbst = 1;
+		stx_int_msk.s.calpar1 = 1;
+		stx_int_msk.s.calpar0 = 1;
+	}
+	cvmx_write_csr(CVMX_STXX_INT_MSK(index), stx_int_msk.u64);
+}
diff --git a/arch/mips/cavium-octeon/executive/cvmx-interrupt-rsl.c b/arch/mips/cavium-octeon/executive/cvmx-interrupt-rsl.c
new file mode 100644
index 000000000..d23f46736
--- /dev/null
+++ b/arch/mips/cavium-octeon/executive/cvmx-interrupt-rsl.c
@@ -0,0 +1,140 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ * Utility functions to decode Octeon's RSL_INT_BLOCKS
+ * interrupts into error messages.
+ */
+
+#include <asm/octeon/octeon.h>
+
+#include <asm/octeon/cvmx-asxx-defs.h>
+#include <asm/octeon/cvmx-gmxx-defs.h>
+
+#ifndef PRINT_ERROR
+#define PRINT_ERROR(format, ...)
+#endif
+
+void __cvmx_interrupt_gmxx_rxx_int_en_enable(int index, int block);
+
+/**
+ * Enable ASX error interrupts that exist on CN3XXX, CN50XX, and
+ * CN58XX.
+ *
+ * @block:  Interface to enable 0-1
+ */
+void __cvmx_interrupt_asxx_enable(int block)
+{
+	int mask;
+	union cvmx_asxx_int_en csr;
+	/*
+	 * CN38XX and CN58XX have two interfaces with 4 ports per
+	 * interface. All other chips have a max of 3 ports on
+	 * interface 0
+	 */
+	if (OCTEON_IS_MODEL(OCTEON_CN38XX) || OCTEON_IS_MODEL(OCTEON_CN58XX))
+		mask = 0xf;	/* Set enables for 4 ports */
+	else
+		mask = 0x7;	/* Set enables for 3 ports */
+
+	/* Enable interface interrupts */
+	csr.u64 = cvmx_read_csr(CVMX_ASXX_INT_EN(block));
+	csr.s.txpsh = mask;
+	csr.s.txpop = mask;
+	csr.s.ovrflw = mask;
+	cvmx_write_csr(CVMX_ASXX_INT_EN(block), csr.u64);
+}
+/**
+ * Enable GMX error reporting for the supplied interface
+ *
+ * @interface: Interface to enable
+ */
+void __cvmx_interrupt_gmxx_enable(int interface)
+{
+	union cvmx_gmxx_inf_mode mode;
+	union cvmx_gmxx_tx_int_en gmx_tx_int_en;
+	int num_ports;
+	int index;
+
+	mode.u64 = cvmx_read_csr(CVMX_GMXX_INF_MODE(interface));
+
+	if (OCTEON_IS_MODEL(OCTEON_CN56XX) || OCTEON_IS_MODEL(OCTEON_CN52XX)) {
+		if (mode.s.en) {
+			switch (mode.cn52xx.mode) {
+			case 1: /* XAUI */
+				num_ports = 1;
+				break;
+			case 2: /* SGMII */
+			case 3: /* PICMG */
+				num_ports = 4;
+				break;
+			default:	/* Disabled */
+				num_ports = 0;
+				break;
+			}
+		} else
+			num_ports = 0;
+	} else {
+		if (mode.s.en) {
+			if (OCTEON_IS_MODEL(OCTEON_CN38XX)
+			    || OCTEON_IS_MODEL(OCTEON_CN58XX)) {
+				/*
+				 * SPI on CN38XX and CN58XX report all
+				 * errors through port 0.  RGMII needs
+				 * to check all 4 ports
+				 */
+				if (mode.s.type)
+					num_ports = 1;
+				else
+					num_ports = 4;
+			} else {
+				/*
+				 * CN30XX, CN31XX, and CN50XX have two
+				 * or three ports. GMII and MII has 2,
+				 * RGMII has three
+				 */
+				if (mode.s.type)
+					num_ports = 2;
+				else
+					num_ports = 3;
+			}
+		} else
+			num_ports = 0;
+	}
+
+	gmx_tx_int_en.u64 = 0;
+	if (num_ports) {
+		if (OCTEON_IS_MODEL(OCTEON_CN38XX)
+		    || OCTEON_IS_MODEL(OCTEON_CN58XX))
+			gmx_tx_int_en.cn38xx.ncb_nxa = 1;
+		gmx_tx_int_en.s.pko_nxa = 1;
+	}
+	gmx_tx_int_en.s.undflw = (1 << num_ports) - 1;
+	cvmx_write_csr(CVMX_GMXX_TX_INT_EN(interface), gmx_tx_int_en.u64);
+	for (index = 0; index < num_ports; index++)
+		__cvmx_interrupt_gmxx_rxx_int_en_enable(index, interface);
+}
diff --git a/arch/mips/cavium-octeon/executive/cvmx-l2c.c b/arch/mips/cavium-octeon/executive/cvmx-l2c.c
new file mode 100644
index 000000000..33b303691
--- /dev/null
+++ b/arch/mips/cavium-octeon/executive/cvmx-l2c.c
@@ -0,0 +1,919 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2017 Cavium, Inc.
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ * Implementation of the Level 2 Cache (L2C) control,
+ * measurement, and debugging facilities.
+ */
+
+#include <linux/compiler.h>
+#include <linux/irqflags.h>
+#include <asm/octeon/cvmx.h>
+#include <asm/octeon/cvmx-l2c.h>
+#include <asm/octeon/cvmx-spinlock.h>
+
+/*
+ * This spinlock is used internally to ensure that only one core is
+ * performing certain L2 operations at a time.
+ *
+ * NOTE: This only protects calls from within a single application -
+ * if multiple applications or operating systems are running, then it
+ * is up to the user program to coordinate between them.
+ */
+static cvmx_spinlock_t cvmx_l2c_spinlock;
+
+int cvmx_l2c_get_core_way_partition(uint32_t core)
+{
+	uint32_t field;
+
+	/* Validate the core number */
+	if (core >= cvmx_octeon_num_cores())
+		return -1;
+
+	if (OCTEON_IS_MODEL(OCTEON_CN63XX))
+		return cvmx_read_csr(CVMX_L2C_WPAR_PPX(core)) & 0xffff;
+
+	/*
+	 * Use the lower two bits of the coreNumber to determine the
+	 * bit offset of the UMSK[] field in the L2C_SPAR register.
+	 */
+	field = (core & 0x3) * 8;
+
+	/*
+	 * Return the UMSK[] field from the appropriate L2C_SPAR
+	 * register based on the coreNumber.
+	 */
+
+	switch (core & 0xC) {
+	case 0x0:
+		return (cvmx_read_csr(CVMX_L2C_SPAR0) & (0xFF << field)) >> field;
+	case 0x4:
+		return (cvmx_read_csr(CVMX_L2C_SPAR1) & (0xFF << field)) >> field;
+	case 0x8:
+		return (cvmx_read_csr(CVMX_L2C_SPAR2) & (0xFF << field)) >> field;
+	case 0xC:
+		return (cvmx_read_csr(CVMX_L2C_SPAR3) & (0xFF << field)) >> field;
+	}
+	return 0;
+}
+
+int cvmx_l2c_set_core_way_partition(uint32_t core, uint32_t mask)
+{
+	uint32_t field;
+	uint32_t valid_mask;
+
+	valid_mask = (0x1 << cvmx_l2c_get_num_assoc()) - 1;
+
+	mask &= valid_mask;
+
+	/* A UMSK setting which blocks all L2C Ways is an error on some chips */
+	if (mask == valid_mask && !OCTEON_IS_MODEL(OCTEON_CN63XX))
+		return -1;
+
+	/* Validate the core number */
+	if (core >= cvmx_octeon_num_cores())
+		return -1;
+
+	if (OCTEON_IS_MODEL(OCTEON_CN63XX)) {
+		cvmx_write_csr(CVMX_L2C_WPAR_PPX(core), mask);
+		return 0;
+	}
+
+	/*
+	 * Use the lower two bits of core to determine the bit offset of the
+	 * UMSK[] field in the L2C_SPAR register.
+	 */
+	field = (core & 0x3) * 8;
+
+	/*
+	 * Assign the new mask setting to the UMSK[] field in the appropriate
+	 * L2C_SPAR register based on the core_num.
+	 *
+	 */
+	switch (core & 0xC) {
+	case 0x0:
+		cvmx_write_csr(CVMX_L2C_SPAR0,
+			       (cvmx_read_csr(CVMX_L2C_SPAR0) & ~(0xFF << field)) |
+			       mask << field);
+		break;
+	case 0x4:
+		cvmx_write_csr(CVMX_L2C_SPAR1,
+			       (cvmx_read_csr(CVMX_L2C_SPAR1) & ~(0xFF << field)) |
+			       mask << field);
+		break;
+	case 0x8:
+		cvmx_write_csr(CVMX_L2C_SPAR2,
+			       (cvmx_read_csr(CVMX_L2C_SPAR2) & ~(0xFF << field)) |
+			       mask << field);
+		break;
+	case 0xC:
+		cvmx_write_csr(CVMX_L2C_SPAR3,
+			       (cvmx_read_csr(CVMX_L2C_SPAR3) & ~(0xFF << field)) |
+			       mask << field);
+		break;
+	}
+	return 0;
+}
+
+int cvmx_l2c_set_hw_way_partition(uint32_t mask)
+{
+	uint32_t valid_mask;
+
+	valid_mask = (0x1 << cvmx_l2c_get_num_assoc()) - 1;
+	mask &= valid_mask;
+
+	/* A UMSK setting which blocks all L2C Ways is an error on some chips */
+	if (mask == valid_mask	&& !OCTEON_IS_MODEL(OCTEON_CN63XX))
+		return -1;
+
+	if (OCTEON_IS_MODEL(OCTEON_CN63XX))
+		cvmx_write_csr(CVMX_L2C_WPAR_IOBX(0), mask);
+	else
+		cvmx_write_csr(CVMX_L2C_SPAR4,
+			       (cvmx_read_csr(CVMX_L2C_SPAR4) & ~0xFF) | mask);
+	return 0;
+}
+
+int cvmx_l2c_get_hw_way_partition(void)
+{
+	if (OCTEON_IS_MODEL(OCTEON_CN63XX))
+		return cvmx_read_csr(CVMX_L2C_WPAR_IOBX(0)) & 0xffff;
+	else
+		return cvmx_read_csr(CVMX_L2C_SPAR4) & (0xFF);
+}
+
+void cvmx_l2c_config_perf(uint32_t counter, enum cvmx_l2c_event event,
+			  uint32_t clear_on_read)
+{
+	if (OCTEON_IS_MODEL(OCTEON_CN5XXX) || OCTEON_IS_MODEL(OCTEON_CN3XXX)) {
+		union cvmx_l2c_pfctl pfctl;
+
+		pfctl.u64 = cvmx_read_csr(CVMX_L2C_PFCTL);
+
+		switch (counter) {
+		case 0:
+			pfctl.s.cnt0sel = event;
+			pfctl.s.cnt0ena = 1;
+			pfctl.s.cnt0rdclr = clear_on_read;
+			break;
+		case 1:
+			pfctl.s.cnt1sel = event;
+			pfctl.s.cnt1ena = 1;
+			pfctl.s.cnt1rdclr = clear_on_read;
+			break;
+		case 2:
+			pfctl.s.cnt2sel = event;
+			pfctl.s.cnt2ena = 1;
+			pfctl.s.cnt2rdclr = clear_on_read;
+			break;
+		case 3:
+		default:
+			pfctl.s.cnt3sel = event;
+			pfctl.s.cnt3ena = 1;
+			pfctl.s.cnt3rdclr = clear_on_read;
+			break;
+		}
+
+		cvmx_write_csr(CVMX_L2C_PFCTL, pfctl.u64);
+	} else {
+		union cvmx_l2c_tadx_prf l2c_tadx_prf;
+		int tad;
+
+		cvmx_dprintf("L2C performance counter events are different for this chip, mapping 'event' to cvmx_l2c_tad_event_t\n");
+		if (clear_on_read)
+			cvmx_dprintf("L2C counters don't support clear on read for this chip\n");
+
+		l2c_tadx_prf.u64 = cvmx_read_csr(CVMX_L2C_TADX_PRF(0));
+
+		switch (counter) {
+		case 0:
+			l2c_tadx_prf.s.cnt0sel = event;
+			break;
+		case 1:
+			l2c_tadx_prf.s.cnt1sel = event;
+			break;
+		case 2:
+			l2c_tadx_prf.s.cnt2sel = event;
+			break;
+		default:
+		case 3:
+			l2c_tadx_prf.s.cnt3sel = event;
+			break;
+		}
+		for (tad = 0; tad < CVMX_L2C_TADS; tad++)
+			cvmx_write_csr(CVMX_L2C_TADX_PRF(tad),
+				       l2c_tadx_prf.u64);
+	}
+}
+
+uint64_t cvmx_l2c_read_perf(uint32_t counter)
+{
+	switch (counter) {
+	case 0:
+		if (OCTEON_IS_MODEL(OCTEON_CN5XXX) || OCTEON_IS_MODEL(OCTEON_CN3XXX))
+			return cvmx_read_csr(CVMX_L2C_PFC0);
+		else {
+			uint64_t counter = 0;
+			int tad;
+
+			for (tad = 0; tad < CVMX_L2C_TADS; tad++)
+				counter += cvmx_read_csr(CVMX_L2C_TADX_PFC0(tad));
+			return counter;
+		}
+	case 1:
+		if (OCTEON_IS_MODEL(OCTEON_CN5XXX) || OCTEON_IS_MODEL(OCTEON_CN3XXX))
+			return cvmx_read_csr(CVMX_L2C_PFC1);
+		else {
+			uint64_t counter = 0;
+			int tad;
+
+			for (tad = 0; tad < CVMX_L2C_TADS; tad++)
+				counter += cvmx_read_csr(CVMX_L2C_TADX_PFC1(tad));
+			return counter;
+		}
+	case 2:
+		if (OCTEON_IS_MODEL(OCTEON_CN5XXX) || OCTEON_IS_MODEL(OCTEON_CN3XXX))
+			return cvmx_read_csr(CVMX_L2C_PFC2);
+		else {
+			uint64_t counter = 0;
+			int tad;
+
+			for (tad = 0; tad < CVMX_L2C_TADS; tad++)
+				counter += cvmx_read_csr(CVMX_L2C_TADX_PFC2(tad));
+			return counter;
+		}
+	case 3:
+	default:
+		if (OCTEON_IS_MODEL(OCTEON_CN5XXX) || OCTEON_IS_MODEL(OCTEON_CN3XXX))
+			return cvmx_read_csr(CVMX_L2C_PFC3);
+		else {
+			uint64_t counter = 0;
+			int tad;
+
+			for (tad = 0; tad < CVMX_L2C_TADS; tad++)
+				counter += cvmx_read_csr(CVMX_L2C_TADX_PFC3(tad));
+			return counter;
+		}
+	}
+}
+
+/*
+ * @INTERNAL
+ * Helper function use to fault in cache lines for L2 cache locking
+ *
+ * @addr:   Address of base of memory region to read into L2 cache
+ * @len:    Length (in bytes) of region to fault in
+ */
+static void fault_in(uint64_t addr, int len)
+{
+	char *ptr;
+
+	/*
+	 * Adjust addr and length so we get all cache lines even for
+	 * small ranges spanning two cache lines.
+	 */
+	len += addr & CVMX_CACHE_LINE_MASK;
+	addr &= ~CVMX_CACHE_LINE_MASK;
+	ptr = cvmx_phys_to_ptr(addr);
+	/*
+	 * Invalidate L1 cache to make sure all loads result in data
+	 * being in L2.
+	 */
+	CVMX_DCACHE_INVALIDATE;
+	while (len > 0) {
+		READ_ONCE(*ptr);
+		len -= CVMX_CACHE_LINE_SIZE;
+		ptr += CVMX_CACHE_LINE_SIZE;
+	}
+}
+
+int cvmx_l2c_lock_line(uint64_t addr)
+{
+	if (OCTEON_IS_MODEL(OCTEON_CN63XX)) {
+		int shift = CVMX_L2C_TAG_ADDR_ALIAS_SHIFT;
+		uint64_t assoc = cvmx_l2c_get_num_assoc();
+		uint64_t tag = addr >> shift;
+		uint64_t index = CVMX_ADD_SEG(CVMX_MIPS_SPACE_XKPHYS, cvmx_l2c_address_to_index(addr) << CVMX_L2C_IDX_ADDR_SHIFT);
+		uint64_t way;
+		union cvmx_l2c_tadx_tag l2c_tadx_tag;
+
+		CVMX_CACHE_LCKL2(CVMX_ADD_SEG(CVMX_MIPS_SPACE_XKPHYS, addr), 0);
+
+		/* Make sure we were able to lock the line */
+		for (way = 0; way < assoc; way++) {
+			CVMX_CACHE_LTGL2I(index | (way << shift), 0);
+			/* make sure CVMX_L2C_TADX_TAG is updated */
+			CVMX_SYNC;
+			l2c_tadx_tag.u64 = cvmx_read_csr(CVMX_L2C_TADX_TAG(0));
+			if (l2c_tadx_tag.s.valid && l2c_tadx_tag.s.tag == tag)
+				break;
+		}
+
+		/* Check if a valid line is found */
+		if (way >= assoc) {
+			/* cvmx_dprintf("ERROR: cvmx_l2c_lock_line: line not found for locking at 0x%llx address\n", (unsigned long long)addr); */
+			return -1;
+		}
+
+		/* Check if lock bit is not set */
+		if (!l2c_tadx_tag.s.lock) {
+			/* cvmx_dprintf("ERROR: cvmx_l2c_lock_line: Not able to lock at 0x%llx address\n", (unsigned long long)addr); */
+			return -1;
+		}
+		return way;
+	} else {
+		int retval = 0;
+		union cvmx_l2c_dbg l2cdbg;
+		union cvmx_l2c_lckbase lckbase;
+		union cvmx_l2c_lckoff lckoff;
+		union cvmx_l2t_err l2t_err;
+
+		cvmx_spinlock_lock(&cvmx_l2c_spinlock);
+
+		l2cdbg.u64 = 0;
+		lckbase.u64 = 0;
+		lckoff.u64 = 0;
+
+		/* Clear l2t error bits if set */
+		l2t_err.u64 = cvmx_read_csr(CVMX_L2T_ERR);
+		l2t_err.s.lckerr = 1;
+		l2t_err.s.lckerr2 = 1;
+		cvmx_write_csr(CVMX_L2T_ERR, l2t_err.u64);
+
+		addr &= ~CVMX_CACHE_LINE_MASK;
+
+		/* Set this core as debug core */
+		l2cdbg.s.ppnum = cvmx_get_core_num();
+		CVMX_SYNC;
+		cvmx_write_csr(CVMX_L2C_DBG, l2cdbg.u64);
+		cvmx_read_csr(CVMX_L2C_DBG);
+
+		lckoff.s.lck_offset = 0; /* Only lock 1 line at a time */
+		cvmx_write_csr(CVMX_L2C_LCKOFF, lckoff.u64);
+		cvmx_read_csr(CVMX_L2C_LCKOFF);
+
+		if (((union cvmx_l2c_cfg)(cvmx_read_csr(CVMX_L2C_CFG))).s.idxalias) {
+			int alias_shift = CVMX_L2C_IDX_ADDR_SHIFT + 2 * CVMX_L2_SET_BITS - 1;
+			uint64_t addr_tmp = addr ^ (addr & ((1 << alias_shift) - 1)) >> CVMX_L2_SET_BITS;
+
+			lckbase.s.lck_base = addr_tmp >> 7;
+
+		} else {
+			lckbase.s.lck_base = addr >> 7;
+		}
+
+		lckbase.s.lck_ena = 1;
+		cvmx_write_csr(CVMX_L2C_LCKBASE, lckbase.u64);
+		/* Make sure it gets there */
+		cvmx_read_csr(CVMX_L2C_LCKBASE);
+
+		fault_in(addr, CVMX_CACHE_LINE_SIZE);
+
+		lckbase.s.lck_ena = 0;
+		cvmx_write_csr(CVMX_L2C_LCKBASE, lckbase.u64);
+		/* Make sure it gets there */
+		cvmx_read_csr(CVMX_L2C_LCKBASE);
+
+		/* Stop being debug core */
+		cvmx_write_csr(CVMX_L2C_DBG, 0);
+		cvmx_read_csr(CVMX_L2C_DBG);
+
+		l2t_err.u64 = cvmx_read_csr(CVMX_L2T_ERR);
+		if (l2t_err.s.lckerr || l2t_err.s.lckerr2)
+			retval = 1;  /* We were unable to lock the line */
+
+		cvmx_spinlock_unlock(&cvmx_l2c_spinlock);
+		return retval;
+	}
+}
+
+int cvmx_l2c_lock_mem_region(uint64_t start, uint64_t len)
+{
+	int retval = 0;
+
+	/* Round start/end to cache line boundaries */
+	len += start & CVMX_CACHE_LINE_MASK;
+	start &= ~CVMX_CACHE_LINE_MASK;
+	len = (len + CVMX_CACHE_LINE_MASK) & ~CVMX_CACHE_LINE_MASK;
+
+	while (len) {
+		retval += cvmx_l2c_lock_line(start);
+		start += CVMX_CACHE_LINE_SIZE;
+		len -= CVMX_CACHE_LINE_SIZE;
+	}
+	return retval;
+}
+
+void cvmx_l2c_flush(void)
+{
+	uint64_t assoc, set;
+	uint64_t n_assoc, n_set;
+
+	n_set = cvmx_l2c_get_num_sets();
+	n_assoc = cvmx_l2c_get_num_assoc();
+
+	if (OCTEON_IS_MODEL(OCTEON_CN6XXX)) {
+		uint64_t address;
+		/* These may look like constants, but they aren't... */
+		int assoc_shift = CVMX_L2C_TAG_ADDR_ALIAS_SHIFT;
+		int set_shift = CVMX_L2C_IDX_ADDR_SHIFT;
+
+		for (set = 0; set < n_set; set++) {
+			for (assoc = 0; assoc < n_assoc; assoc++) {
+				address = CVMX_ADD_SEG(CVMX_MIPS_SPACE_XKPHYS,
+						       (assoc << assoc_shift) | (set << set_shift));
+				CVMX_CACHE_WBIL2I(address, 0);
+			}
+		}
+	} else {
+		for (set = 0; set < n_set; set++)
+			for (assoc = 0; assoc < n_assoc; assoc++)
+				cvmx_l2c_flush_line(assoc, set);
+	}
+}
+
+
+int cvmx_l2c_unlock_line(uint64_t address)
+{
+
+	if (OCTEON_IS_MODEL(OCTEON_CN63XX)) {
+		int assoc;
+		union cvmx_l2c_tag tag;
+		uint32_t tag_addr;
+		uint32_t index = cvmx_l2c_address_to_index(address);
+
+		tag_addr = ((address >> CVMX_L2C_TAG_ADDR_ALIAS_SHIFT) & ((1 << CVMX_L2C_TAG_ADDR_ALIAS_SHIFT) - 1));
+
+		/*
+		 * For 63XX, we can flush a line by using the physical
+		 * address directly, so finding the cache line used by
+		 * the address is only required to provide the proper
+		 * return value for the function.
+		 */
+		for (assoc = 0; assoc < CVMX_L2_ASSOC; assoc++) {
+			tag = cvmx_l2c_get_tag(assoc, index);
+
+			if (tag.s.V && (tag.s.addr == tag_addr)) {
+				CVMX_CACHE_WBIL2(CVMX_ADD_SEG(CVMX_MIPS_SPACE_XKPHYS, address), 0);
+				return tag.s.L;
+			}
+		}
+	} else {
+		int assoc;
+		union cvmx_l2c_tag tag;
+		uint32_t tag_addr;
+
+		uint32_t index = cvmx_l2c_address_to_index(address);
+
+		/* Compute portion of address that is stored in tag */
+		tag_addr = ((address >> CVMX_L2C_TAG_ADDR_ALIAS_SHIFT) & ((1 << CVMX_L2C_TAG_ADDR_ALIAS_SHIFT) - 1));
+		for (assoc = 0; assoc < CVMX_L2_ASSOC; assoc++) {
+			tag = cvmx_l2c_get_tag(assoc, index);
+
+			if (tag.s.V && (tag.s.addr == tag_addr)) {
+				cvmx_l2c_flush_line(assoc, index);
+				return tag.s.L;
+			}
+		}
+	}
+	return 0;
+}
+
+int cvmx_l2c_unlock_mem_region(uint64_t start, uint64_t len)
+{
+	int num_unlocked = 0;
+	/* Round start/end to cache line boundaries */
+	len += start & CVMX_CACHE_LINE_MASK;
+	start &= ~CVMX_CACHE_LINE_MASK;
+	len = (len + CVMX_CACHE_LINE_MASK) & ~CVMX_CACHE_LINE_MASK;
+	while (len > 0) {
+		num_unlocked += cvmx_l2c_unlock_line(start);
+		start += CVMX_CACHE_LINE_SIZE;
+		len -= CVMX_CACHE_LINE_SIZE;
+	}
+
+	return num_unlocked;
+}
+
+/*
+ * Internal l2c tag types.  These are converted to a generic structure
+ * that can be used on all chips.
+ */
+union __cvmx_l2c_tag {
+	uint64_t u64;
+	struct cvmx_l2c_tag_cn50xx {
+		__BITFIELD_FIELD(uint64_t reserved:40,
+		__BITFIELD_FIELD(uint64_t V:1,		/* Line valid */
+		__BITFIELD_FIELD(uint64_t D:1,		/* Line dirty */
+		__BITFIELD_FIELD(uint64_t L:1,		/* Line locked */
+		__BITFIELD_FIELD(uint64_t U:1,		/* Use, LRU eviction */
+		__BITFIELD_FIELD(uint64_t addr:20,	/* Phys addr (33..14) */
+		;))))))
+	} cn50xx;
+	struct cvmx_l2c_tag_cn30xx {
+		__BITFIELD_FIELD(uint64_t reserved:41,
+		__BITFIELD_FIELD(uint64_t V:1,		/* Line valid */
+		__BITFIELD_FIELD(uint64_t D:1,		/* Line dirty */
+		__BITFIELD_FIELD(uint64_t L:1,		/* Line locked */
+		__BITFIELD_FIELD(uint64_t U:1,		/* Use, LRU eviction */
+		__BITFIELD_FIELD(uint64_t addr:19,	/* Phys addr (33..15) */
+		;))))))
+	} cn30xx;
+	struct cvmx_l2c_tag_cn31xx {
+		__BITFIELD_FIELD(uint64_t reserved:42,
+		__BITFIELD_FIELD(uint64_t V:1,		/* Line valid */
+		__BITFIELD_FIELD(uint64_t D:1,		/* Line dirty */
+		__BITFIELD_FIELD(uint64_t L:1,		/* Line locked */
+		__BITFIELD_FIELD(uint64_t U:1,		/* Use, LRU eviction */
+		__BITFIELD_FIELD(uint64_t addr:18,	/* Phys addr (33..16) */
+		;))))))
+	} cn31xx;
+	struct cvmx_l2c_tag_cn38xx {
+		__BITFIELD_FIELD(uint64_t reserved:43,
+		__BITFIELD_FIELD(uint64_t V:1,		/* Line valid */
+		__BITFIELD_FIELD(uint64_t D:1,		/* Line dirty */
+		__BITFIELD_FIELD(uint64_t L:1,		/* Line locked */
+		__BITFIELD_FIELD(uint64_t U:1,		/* Use, LRU eviction */
+		__BITFIELD_FIELD(uint64_t addr:17,	/* Phys addr (33..17) */
+		;))))))
+	} cn38xx;
+	struct cvmx_l2c_tag_cn58xx {
+		__BITFIELD_FIELD(uint64_t reserved:44,
+		__BITFIELD_FIELD(uint64_t V:1,		/* Line valid */
+		__BITFIELD_FIELD(uint64_t D:1,		/* Line dirty */
+		__BITFIELD_FIELD(uint64_t L:1,		/* Line locked */
+		__BITFIELD_FIELD(uint64_t U:1,		/* Use, LRU eviction */
+		__BITFIELD_FIELD(uint64_t addr:16,	/* Phys addr (33..18) */
+		;))))))
+	} cn58xx;
+	struct cvmx_l2c_tag_cn58xx cn56xx;	/* 2048 sets */
+	struct cvmx_l2c_tag_cn31xx cn52xx;	/* 512 sets */
+};
+
+
+/*
+ * @INTERNAL
+ * Function to read a L2C tag.  This code make the current core
+ * the 'debug core' for the L2.  This code must only be executed by
+ * 1 core at a time.
+ *
+ * @assoc:  Association (way) of the tag to dump
+ * @index:  Index of the cacheline
+ *
+ * Returns The Octeon model specific tag structure.  This is
+ *	   translated by a wrapper function to a generic form that is
+ *	   easier for applications to use.
+ */
+static union __cvmx_l2c_tag __read_l2_tag(uint64_t assoc, uint64_t index)
+{
+
+	uint64_t debug_tag_addr = CVMX_ADD_SEG(CVMX_MIPS_SPACE_XKPHYS, (index << 7) + 96);
+	uint64_t core = cvmx_get_core_num();
+	union __cvmx_l2c_tag tag_val;
+	uint64_t dbg_addr = CVMX_L2C_DBG;
+	unsigned long flags;
+	union cvmx_l2c_dbg debug_val;
+
+	debug_val.u64 = 0;
+	/*
+	 * For low core count parts, the core number is always small
+	 * enough to stay in the correct field and not set any
+	 * reserved bits.
+	 */
+	debug_val.s.ppnum = core;
+	debug_val.s.l2t = 1;
+	debug_val.s.set = assoc;
+
+	local_irq_save(flags);
+	/*
+	 * Make sure core is quiet (no prefetches, etc.) before
+	 * entering debug mode.
+	 */
+	CVMX_SYNC;
+	/* Flush L1 to make sure debug load misses L1 */
+	CVMX_DCACHE_INVALIDATE;
+
+	/*
+	 * The following must be done in assembly as when in debug
+	 * mode all data loads from L2 return special debug data, not
+	 * normal memory contents.  Also, interrupts must be disabled,
+	 * since if an interrupt occurs while in debug mode the ISR
+	 * will get debug data from all its memory * reads instead of
+	 * the contents of memory.
+	 */
+
+	asm volatile (
+		".set push\n\t"
+		".set mips64\n\t"
+		".set noreorder\n\t"
+		"sd    %[dbg_val], 0(%[dbg_addr])\n\t"	 /* Enter debug mode, wait for store */
+		"ld    $0, 0(%[dbg_addr])\n\t"
+		"ld    %[tag_val], 0(%[tag_addr])\n\t"	 /* Read L2C tag data */
+		"sd    $0, 0(%[dbg_addr])\n\t"		/* Exit debug mode, wait for store */
+		"ld    $0, 0(%[dbg_addr])\n\t"
+		"cache 9, 0($0)\n\t"		 /* Invalidate dcache to discard debug data */
+		".set pop"
+		: [tag_val] "=r" (tag_val)
+		: [dbg_addr] "r" (dbg_addr), [dbg_val] "r" (debug_val), [tag_addr] "r" (debug_tag_addr)
+		: "memory");
+
+	local_irq_restore(flags);
+
+	return tag_val;
+}
+
+
+union cvmx_l2c_tag cvmx_l2c_get_tag(uint32_t association, uint32_t index)
+{
+	union cvmx_l2c_tag tag;
+
+	tag.u64 = 0;
+	if ((int)association >= cvmx_l2c_get_num_assoc()) {
+		cvmx_dprintf("ERROR: cvmx_l2c_get_tag association out of range\n");
+		return tag;
+	}
+	if ((int)index >= cvmx_l2c_get_num_sets()) {
+		cvmx_dprintf("ERROR: cvmx_l2c_get_tag index out of range (arg: %d, max: %d)\n",
+			     (int)index, cvmx_l2c_get_num_sets());
+		return tag;
+	}
+	if (OCTEON_IS_MODEL(OCTEON_CN63XX)) {
+		union cvmx_l2c_tadx_tag l2c_tadx_tag;
+		uint64_t address = CVMX_ADD_SEG(CVMX_MIPS_SPACE_XKPHYS,
+						(association << CVMX_L2C_TAG_ADDR_ALIAS_SHIFT) |
+						(index << CVMX_L2C_IDX_ADDR_SHIFT));
+		/*
+		 * Use L2 cache Index load tag cache instruction, as
+		 * hardware loads the virtual tag for the L2 cache
+		 * block with the contents of L2C_TAD0_TAG
+		 * register.
+		 */
+		CVMX_CACHE_LTGL2I(address, 0);
+		CVMX_SYNC;   /* make sure CVMX_L2C_TADX_TAG is updated */
+		l2c_tadx_tag.u64 = cvmx_read_csr(CVMX_L2C_TADX_TAG(0));
+
+		tag.s.V	    = l2c_tadx_tag.s.valid;
+		tag.s.D	    = l2c_tadx_tag.s.dirty;
+		tag.s.L	    = l2c_tadx_tag.s.lock;
+		tag.s.U	    = l2c_tadx_tag.s.use;
+		tag.s.addr  = l2c_tadx_tag.s.tag;
+	} else {
+		union __cvmx_l2c_tag tmp_tag;
+		/* __read_l2_tag is intended for internal use only */
+		tmp_tag = __read_l2_tag(association, index);
+
+		/*
+		 * Convert all tag structure types to generic version,
+		 * as it can represent all models.
+		 */
+		if (OCTEON_IS_MODEL(OCTEON_CN58XX) || OCTEON_IS_MODEL(OCTEON_CN56XX)) {
+			tag.s.V	   = tmp_tag.cn58xx.V;
+			tag.s.D	   = tmp_tag.cn58xx.D;
+			tag.s.L	   = tmp_tag.cn58xx.L;
+			tag.s.U	   = tmp_tag.cn58xx.U;
+			tag.s.addr = tmp_tag.cn58xx.addr;
+		} else if (OCTEON_IS_MODEL(OCTEON_CN38XX)) {
+			tag.s.V	   = tmp_tag.cn38xx.V;
+			tag.s.D	   = tmp_tag.cn38xx.D;
+			tag.s.L	   = tmp_tag.cn38xx.L;
+			tag.s.U	   = tmp_tag.cn38xx.U;
+			tag.s.addr = tmp_tag.cn38xx.addr;
+		} else if (OCTEON_IS_MODEL(OCTEON_CN31XX) || OCTEON_IS_MODEL(OCTEON_CN52XX)) {
+			tag.s.V	   = tmp_tag.cn31xx.V;
+			tag.s.D	   = tmp_tag.cn31xx.D;
+			tag.s.L	   = tmp_tag.cn31xx.L;
+			tag.s.U	   = tmp_tag.cn31xx.U;
+			tag.s.addr = tmp_tag.cn31xx.addr;
+		} else if (OCTEON_IS_MODEL(OCTEON_CN30XX)) {
+			tag.s.V	   = tmp_tag.cn30xx.V;
+			tag.s.D	   = tmp_tag.cn30xx.D;
+			tag.s.L	   = tmp_tag.cn30xx.L;
+			tag.s.U	   = tmp_tag.cn30xx.U;
+			tag.s.addr = tmp_tag.cn30xx.addr;
+		} else if (OCTEON_IS_MODEL(OCTEON_CN50XX)) {
+			tag.s.V	   = tmp_tag.cn50xx.V;
+			tag.s.D	   = tmp_tag.cn50xx.D;
+			tag.s.L	   = tmp_tag.cn50xx.L;
+			tag.s.U	   = tmp_tag.cn50xx.U;
+			tag.s.addr = tmp_tag.cn50xx.addr;
+		} else {
+			cvmx_dprintf("Unsupported OCTEON Model in %s\n", __func__);
+		}
+	}
+	return tag;
+}
+
+uint32_t cvmx_l2c_address_to_index(uint64_t addr)
+{
+	uint64_t idx = addr >> CVMX_L2C_IDX_ADDR_SHIFT;
+	int indxalias = 0;
+
+	if (OCTEON_IS_MODEL(OCTEON_CN6XXX)) {
+		union cvmx_l2c_ctl l2c_ctl;
+
+		l2c_ctl.u64 = cvmx_read_csr(CVMX_L2C_CTL);
+		indxalias = !l2c_ctl.s.disidxalias;
+	} else {
+		union cvmx_l2c_cfg l2c_cfg;
+
+		l2c_cfg.u64 = cvmx_read_csr(CVMX_L2C_CFG);
+		indxalias = l2c_cfg.s.idxalias;
+	}
+
+	if (indxalias) {
+		if (OCTEON_IS_MODEL(OCTEON_CN63XX)) {
+			uint32_t a_14_12 = (idx / (CVMX_L2C_MEMBANK_SELECT_SIZE/(1<<CVMX_L2C_IDX_ADDR_SHIFT))) & 0x7;
+
+			idx ^= idx / cvmx_l2c_get_num_sets();
+			idx ^= a_14_12;
+		} else {
+			idx ^= ((addr & CVMX_L2C_ALIAS_MASK) >> CVMX_L2C_TAG_ADDR_ALIAS_SHIFT);
+		}
+	}
+	idx &= CVMX_L2C_IDX_MASK;
+	return idx;
+}
+
+int cvmx_l2c_get_cache_size_bytes(void)
+{
+	return cvmx_l2c_get_num_sets() * cvmx_l2c_get_num_assoc() *
+		CVMX_CACHE_LINE_SIZE;
+}
+
+/*
+ * Return log base 2 of the number of sets in the L2 cache
+ */
+int cvmx_l2c_get_set_bits(void)
+{
+	int l2_set_bits;
+
+	if (OCTEON_IS_MODEL(OCTEON_CN56XX) || OCTEON_IS_MODEL(OCTEON_CN58XX))
+		l2_set_bits = 11;	/* 2048 sets */
+	else if (OCTEON_IS_MODEL(OCTEON_CN38XX) || OCTEON_IS_MODEL(OCTEON_CN63XX))
+		l2_set_bits = 10;	/* 1024 sets */
+	else if (OCTEON_IS_MODEL(OCTEON_CN31XX) || OCTEON_IS_MODEL(OCTEON_CN52XX))
+		l2_set_bits = 9;	/* 512 sets */
+	else if (OCTEON_IS_MODEL(OCTEON_CN30XX))
+		l2_set_bits = 8;	/* 256 sets */
+	else if (OCTEON_IS_MODEL(OCTEON_CN50XX))
+		l2_set_bits = 7;	/* 128 sets */
+	else {
+		cvmx_dprintf("Unsupported OCTEON Model in %s\n", __func__);
+		l2_set_bits = 11;	/* 2048 sets */
+	}
+	return l2_set_bits;
+}
+
+/* Return the number of sets in the L2 Cache */
+int cvmx_l2c_get_num_sets(void)
+{
+	return 1 << cvmx_l2c_get_set_bits();
+}
+
+/* Return the number of associations in the L2 Cache */
+int cvmx_l2c_get_num_assoc(void)
+{
+	int l2_assoc;
+
+	if (OCTEON_IS_MODEL(OCTEON_CN56XX) ||
+	    OCTEON_IS_MODEL(OCTEON_CN52XX) ||
+	    OCTEON_IS_MODEL(OCTEON_CN58XX) ||
+	    OCTEON_IS_MODEL(OCTEON_CN50XX) ||
+	    OCTEON_IS_MODEL(OCTEON_CN38XX))
+		l2_assoc = 8;
+	else if (OCTEON_IS_MODEL(OCTEON_CN63XX))
+		l2_assoc = 16;
+	else if (OCTEON_IS_MODEL(OCTEON_CN31XX) ||
+		 OCTEON_IS_MODEL(OCTEON_CN30XX))
+		l2_assoc = 4;
+	else {
+		cvmx_dprintf("Unsupported OCTEON Model in %s\n", __func__);
+		l2_assoc = 8;
+	}
+
+	/* Check to see if part of the cache is disabled */
+	if (OCTEON_IS_MODEL(OCTEON_CN63XX)) {
+		union cvmx_mio_fus_dat3 mio_fus_dat3;
+
+		mio_fus_dat3.u64 = cvmx_read_csr(CVMX_MIO_FUS_DAT3);
+		/*
+		 * cvmx_mio_fus_dat3.s.l2c_crip fuses map as follows
+		 * <2> will be not used for 63xx
+		 * <1> disables 1/2 ways
+		 * <0> disables 1/4 ways
+		 * They are cumulative, so for 63xx:
+		 * <1> <0>
+		 * 0 0 16-way 2MB cache
+		 * 0 1 12-way 1.5MB cache
+		 * 1 0 8-way 1MB cache
+		 * 1 1 4-way 512KB cache
+		 */
+
+		if (mio_fus_dat3.s.l2c_crip == 3)
+			l2_assoc = 4;
+		else if (mio_fus_dat3.s.l2c_crip == 2)
+			l2_assoc = 8;
+		else if (mio_fus_dat3.s.l2c_crip == 1)
+			l2_assoc = 12;
+	} else {
+		uint64_t l2d_fus3;
+
+		l2d_fus3 = cvmx_read_csr(CVMX_L2D_FUS3);
+		/*
+		 * Using shifts here, as bit position names are
+		 * different for each model but they all mean the
+		 * same.
+		 */
+		if ((l2d_fus3 >> 35) & 0x1)
+			l2_assoc = l2_assoc >> 2;
+		else if ((l2d_fus3 >> 34) & 0x1)
+			l2_assoc = l2_assoc >> 1;
+	}
+	return l2_assoc;
+}
+
+/*
+ * Flush a line from the L2 cache
+ * This should only be called from one core at a time, as this routine
+ * sets the core to the 'debug' core in order to flush the line.
+ *
+ * @assoc:  Association (or way) to flush
+ * @index:  Index to flush
+ */
+void cvmx_l2c_flush_line(uint32_t assoc, uint32_t index)
+{
+	/* Check the range of the index. */
+	if (index > (uint32_t)cvmx_l2c_get_num_sets()) {
+		cvmx_dprintf("ERROR: cvmx_l2c_flush_line index out of range.\n");
+		return;
+	}
+
+	/* Check the range of association. */
+	if (assoc > (uint32_t)cvmx_l2c_get_num_assoc()) {
+		cvmx_dprintf("ERROR: cvmx_l2c_flush_line association out of range.\n");
+		return;
+	}
+
+	if (OCTEON_IS_MODEL(OCTEON_CN63XX)) {
+		uint64_t address;
+		/* Create the address based on index and association.
+		 * Bits<20:17> select the way of the cache block involved in
+		 *	       the operation
+		 * Bits<16:7> of the effect address select the index
+		 */
+		address = CVMX_ADD_SEG(CVMX_MIPS_SPACE_XKPHYS,
+				(assoc << CVMX_L2C_TAG_ADDR_ALIAS_SHIFT) |
+				(index << CVMX_L2C_IDX_ADDR_SHIFT));
+		CVMX_CACHE_WBIL2I(address, 0);
+	} else {
+		union cvmx_l2c_dbg l2cdbg;
+
+		l2cdbg.u64 = 0;
+		if (!OCTEON_IS_MODEL(OCTEON_CN30XX))
+			l2cdbg.s.ppnum = cvmx_get_core_num();
+		l2cdbg.s.finv = 1;
+
+		l2cdbg.s.set = assoc;
+		cvmx_spinlock_lock(&cvmx_l2c_spinlock);
+		/*
+		 * Enter debug mode, and make sure all other writes
+		 * complete before we enter debug mode
+		 */
+		CVMX_SYNC;
+		cvmx_write_csr(CVMX_L2C_DBG, l2cdbg.u64);
+		cvmx_read_csr(CVMX_L2C_DBG);
+
+		CVMX_PREPARE_FOR_STORE(CVMX_ADD_SEG(CVMX_MIPS_SPACE_XKPHYS,
+						    index * CVMX_CACHE_LINE_SIZE),
+				       0);
+		/* Exit debug mode */
+		CVMX_SYNC;
+		cvmx_write_csr(CVMX_L2C_DBG, 0);
+		cvmx_read_csr(CVMX_L2C_DBG);
+		cvmx_spinlock_unlock(&cvmx_l2c_spinlock);
+	}
+}
diff --git a/arch/mips/cavium-octeon/executive/cvmx-pko.c b/arch/mips/cavium-octeon/executive/cvmx-pko.c
new file mode 100644
index 000000000..15faca494
--- /dev/null
+++ b/arch/mips/cavium-octeon/executive/cvmx-pko.c
@@ -0,0 +1,632 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ * Support library for the hardware Packet Output unit.
+ */
+
+#include <asm/octeon/octeon.h>
+
+#include <asm/octeon/cvmx-config.h>
+#include <asm/octeon/cvmx-pko.h>
+#include <asm/octeon/cvmx-helper.h>
+
+/*
+ * Internal state of packet output
+ */
+
+static int __cvmx_pko_int(int interface, int index)
+{
+	switch (interface) {
+	case 0:
+		return index;
+	case 1:
+		return 4;
+	case 2:
+		return index + 0x08;
+	case 3:
+		return index + 0x0c;
+	case 4:
+		return index + 0x10;
+	case 5:
+		return 0x1c;
+	case 6:
+		return 0x1d;
+	case 7:
+		return 0x1e;
+	case 8:
+		return 0x1f;
+	default:
+		return -1;
+	}
+}
+
+static void __cvmx_pko_iport_config(int pko_port)
+{
+	int queue;
+	const int num_queues = 1;
+	const int base_queue = pko_port;
+	const int static_priority_end = 1;
+	const int static_priority_base = 1;
+
+	for (queue = 0; queue < num_queues; queue++) {
+		union cvmx_pko_mem_iqueue_ptrs config;
+		cvmx_cmd_queue_result_t cmd_res;
+		uint64_t *buf_ptr;
+
+		config.u64		= 0;
+		config.s.index		= queue;
+		config.s.qid		= base_queue + queue;
+		config.s.ipid		= pko_port;
+		config.s.tail		= (queue == (num_queues - 1));
+		config.s.s_tail		= (queue == static_priority_end);
+		config.s.static_p	= (static_priority_base >= 0);
+		config.s.static_q	= (queue <= static_priority_end);
+		config.s.qos_mask	= 0xff;
+
+		cmd_res = cvmx_cmd_queue_initialize(
+				CVMX_CMD_QUEUE_PKO(base_queue + queue),
+				CVMX_PKO_MAX_QUEUE_DEPTH,
+				CVMX_FPA_OUTPUT_BUFFER_POOL,
+				(CVMX_FPA_OUTPUT_BUFFER_POOL_SIZE -
+				 CVMX_PKO_COMMAND_BUFFER_SIZE_ADJUST * 8));
+
+		WARN(cmd_res,
+		     "%s: cmd_res=%d pko_port=%d base_queue=%d num_queues=%d queue=%d\n",
+			__func__, (int)cmd_res, pko_port, base_queue,
+			num_queues, queue);
+
+		buf_ptr = (uint64_t *)cvmx_cmd_queue_buffer(
+				CVMX_CMD_QUEUE_PKO(base_queue + queue));
+		config.s.buf_ptr = cvmx_ptr_to_phys(buf_ptr) >> 7;
+		CVMX_SYNCWS;
+		cvmx_write_csr(CVMX_PKO_MEM_IQUEUE_PTRS, config.u64);
+	}
+}
+
+static void __cvmx_pko_queue_alloc_o68(void)
+{
+	int port;
+
+	for (port = 0; port < 48; port++)
+		__cvmx_pko_iport_config(port);
+}
+
+static void __cvmx_pko_port_map_o68(void)
+{
+	int port;
+	int interface, index;
+	cvmx_helper_interface_mode_t mode;
+	union cvmx_pko_mem_iport_ptrs config;
+
+	/*
+	 * Initialize every iport with the invalid eid.
+	 */
+	config.u64 = 0;
+	config.s.eid = 31; /* Invalid */
+	for (port = 0; port < 128; port++) {
+		config.s.ipid = port;
+		cvmx_write_csr(CVMX_PKO_MEM_IPORT_PTRS, config.u64);
+	}
+
+	/*
+	 * Set up PKO_MEM_IPORT_PTRS
+	 */
+	for (port = 0; port < 48; port++) {
+		interface = cvmx_helper_get_interface_num(port);
+		index = cvmx_helper_get_interface_index_num(port);
+		mode = cvmx_helper_interface_get_mode(interface);
+		if (mode == CVMX_HELPER_INTERFACE_MODE_DISABLED)
+			continue;
+
+		config.s.ipid = port;
+		config.s.qos_mask = 0xff;
+		config.s.crc = 1;
+		config.s.min_pkt = 1;
+		config.s.intr = __cvmx_pko_int(interface, index);
+		config.s.eid = config.s.intr;
+		config.s.pipe = (mode == CVMX_HELPER_INTERFACE_MODE_LOOP) ?
+			index : port;
+		cvmx_write_csr(CVMX_PKO_MEM_IPORT_PTRS, config.u64);
+	}
+}
+
+static void __cvmx_pko_chip_init(void)
+{
+	int i;
+
+	if (OCTEON_IS_MODEL(OCTEON_CN68XX)) {
+		__cvmx_pko_port_map_o68();
+		__cvmx_pko_queue_alloc_o68();
+		return;
+	}
+
+	/*
+	 * Initialize queues
+	 */
+	for (i = 0; i < CVMX_PKO_MAX_OUTPUT_QUEUES; i++) {
+		const uint64_t priority = 8;
+
+		cvmx_pko_config_port(CVMX_PKO_MEM_QUEUE_PTRS_ILLEGAL_PID, i, 1,
+				     &priority);
+	}
+}
+
+/*
+ * Call before any other calls to initialize the packet
+ * output system.  This does chip global config, and should only be
+ * done by one core.
+ */
+
+void cvmx_pko_initialize_global(void)
+{
+	union cvmx_pko_reg_cmd_buf config;
+
+	/*
+	 * Set the size of the PKO command buffers to an odd number of
+	 * 64bit words. This allows the normal two word send to stay
+	 * aligned and never span a command word buffer.
+	 */
+	config.u64 = 0;
+	config.s.pool = CVMX_FPA_OUTPUT_BUFFER_POOL;
+	config.s.size = CVMX_FPA_OUTPUT_BUFFER_POOL_SIZE / 8 - 1;
+
+	cvmx_write_csr(CVMX_PKO_REG_CMD_BUF, config.u64);
+
+	/*
+	 * Chip-specific setup.
+	 */
+	__cvmx_pko_chip_init();
+
+	/*
+	 * If we aren't using all of the queues optimize PKO's
+	 * internal memory.
+	 */
+	if (OCTEON_IS_MODEL(OCTEON_CN38XX) || OCTEON_IS_MODEL(OCTEON_CN58XX)
+	    || OCTEON_IS_MODEL(OCTEON_CN56XX)
+	    || OCTEON_IS_MODEL(OCTEON_CN52XX)) {
+		int num_interfaces = cvmx_helper_get_number_of_interfaces();
+		int last_port =
+		    cvmx_helper_get_last_ipd_port(num_interfaces - 1);
+		int max_queues =
+		    cvmx_pko_get_base_queue(last_port) +
+		    cvmx_pko_get_num_queues(last_port);
+		if (OCTEON_IS_MODEL(OCTEON_CN38XX)) {
+			if (max_queues <= 32)
+				cvmx_write_csr(CVMX_PKO_REG_QUEUE_MODE, 2);
+			else if (max_queues <= 64)
+				cvmx_write_csr(CVMX_PKO_REG_QUEUE_MODE, 1);
+		} else {
+			if (max_queues <= 64)
+				cvmx_write_csr(CVMX_PKO_REG_QUEUE_MODE, 2);
+			else if (max_queues <= 128)
+				cvmx_write_csr(CVMX_PKO_REG_QUEUE_MODE, 1);
+		}
+	}
+}
+
+/*
+ * Enables the packet output hardware. It must already be
+ * configured.
+ */
+void cvmx_pko_enable(void)
+{
+	union cvmx_pko_reg_flags flags;
+
+	flags.u64 = cvmx_read_csr(CVMX_PKO_REG_FLAGS);
+	if (flags.s.ena_pko)
+		cvmx_dprintf
+		    ("Warning: Enabling PKO when PKO already enabled.\n");
+
+	flags.s.ena_dwb = 1;
+	flags.s.ena_pko = 1;
+	/*
+	 * always enable big endian for 3-word command. Does nothing
+	 * for 2-word.
+	 */
+	flags.s.store_be = 1;
+	cvmx_write_csr(CVMX_PKO_REG_FLAGS, flags.u64);
+}
+
+/*
+ * Disables the packet output. Does not affect any configuration.
+ */
+void cvmx_pko_disable(void)
+{
+	union cvmx_pko_reg_flags pko_reg_flags;
+	pko_reg_flags.u64 = cvmx_read_csr(CVMX_PKO_REG_FLAGS);
+	pko_reg_flags.s.ena_pko = 0;
+	cvmx_write_csr(CVMX_PKO_REG_FLAGS, pko_reg_flags.u64);
+}
+EXPORT_SYMBOL_GPL(cvmx_pko_disable);
+
+/*
+ * Reset the packet output.
+ */
+static void __cvmx_pko_reset(void)
+{
+	union cvmx_pko_reg_flags pko_reg_flags;
+	pko_reg_flags.u64 = cvmx_read_csr(CVMX_PKO_REG_FLAGS);
+	pko_reg_flags.s.reset = 1;
+	cvmx_write_csr(CVMX_PKO_REG_FLAGS, pko_reg_flags.u64);
+}
+
+/*
+ * Shutdown and free resources required by packet output.
+ */
+void cvmx_pko_shutdown(void)
+{
+	union cvmx_pko_mem_queue_ptrs config;
+	int queue;
+
+	cvmx_pko_disable();
+
+	for (queue = 0; queue < CVMX_PKO_MAX_OUTPUT_QUEUES; queue++) {
+		config.u64 = 0;
+		config.s.tail = 1;
+		config.s.index = 0;
+		config.s.port = CVMX_PKO_MEM_QUEUE_PTRS_ILLEGAL_PID;
+		config.s.queue = queue & 0x7f;
+		config.s.qos_mask = 0;
+		config.s.buf_ptr = 0;
+		if (!OCTEON_IS_MODEL(OCTEON_CN3XXX)) {
+			union cvmx_pko_reg_queue_ptrs1 config1;
+			config1.u64 = 0;
+			config1.s.qid7 = queue >> 7;
+			cvmx_write_csr(CVMX_PKO_REG_QUEUE_PTRS1, config1.u64);
+		}
+		cvmx_write_csr(CVMX_PKO_MEM_QUEUE_PTRS, config.u64);
+		cvmx_cmd_queue_shutdown(CVMX_CMD_QUEUE_PKO(queue));
+	}
+	__cvmx_pko_reset();
+}
+EXPORT_SYMBOL_GPL(cvmx_pko_shutdown);
+
+/*
+ * Configure a output port and the associated queues for use.
+ *
+ * @port:	Port to configure.
+ * @base_queue: First queue number to associate with this port.
+ * @num_queues: Number of queues to associate with this port
+ * @priority:	Array of priority levels for each queue. Values are
+ *		     allowed to be 0-8. A value of 8 get 8 times the traffic
+ *		     of a value of 1.  A value of 0 indicates that no rounds
+ *		     will be participated in. These priorities can be changed
+ *		     on the fly while the pko is enabled. A priority of 9
+ *		     indicates that static priority should be used.  If static
+ *		     priority is used all queues with static priority must be
+ *		     contiguous starting at the base_queue, and lower numbered
+ *		     queues have higher priority than higher numbered queues.
+ *		     There must be num_queues elements in the array.
+ */
+cvmx_pko_status_t cvmx_pko_config_port(uint64_t port, uint64_t base_queue,
+				       uint64_t num_queues,
+				       const uint64_t priority[])
+{
+	cvmx_pko_status_t result_code;
+	uint64_t queue;
+	union cvmx_pko_mem_queue_ptrs config;
+	union cvmx_pko_reg_queue_ptrs1 config1;
+	int static_priority_base = -1;
+	int static_priority_end = -1;
+
+	if (OCTEON_IS_MODEL(OCTEON_CN68XX))
+		return CVMX_PKO_SUCCESS;
+
+	if ((port >= CVMX_PKO_NUM_OUTPUT_PORTS)
+	    && (port != CVMX_PKO_MEM_QUEUE_PTRS_ILLEGAL_PID)) {
+		cvmx_dprintf("ERROR: cvmx_pko_config_port: Invalid port %llu\n",
+			     (unsigned long long)port);
+		return CVMX_PKO_INVALID_PORT;
+	}
+
+	if (base_queue + num_queues > CVMX_PKO_MAX_OUTPUT_QUEUES) {
+		cvmx_dprintf
+		    ("ERROR: cvmx_pko_config_port: Invalid queue range %llu\n",
+		     (unsigned long long)(base_queue + num_queues));
+		return CVMX_PKO_INVALID_QUEUE;
+	}
+
+	if (port != CVMX_PKO_MEM_QUEUE_PTRS_ILLEGAL_PID) {
+		/*
+		 * Validate the static queue priority setup and set
+		 * static_priority_base and static_priority_end
+		 * accordingly.
+		 */
+		for (queue = 0; queue < num_queues; queue++) {
+			/* Find first queue of static priority */
+			if (static_priority_base == -1
+			    && priority[queue] ==
+			    CVMX_PKO_QUEUE_STATIC_PRIORITY)
+				static_priority_base = queue;
+			/* Find last queue of static priority */
+			if (static_priority_base != -1
+			    && static_priority_end == -1
+			    && priority[queue] != CVMX_PKO_QUEUE_STATIC_PRIORITY
+			    && queue)
+				static_priority_end = queue - 1;
+			else if (static_priority_base != -1
+				 && static_priority_end == -1
+				 && queue == num_queues - 1)
+				/* all queues are static priority */
+				static_priority_end = queue;
+			/*
+			 * Check to make sure all static priority
+			 * queues are contiguous.  Also catches some
+			 * cases of static priorities not starting at
+			 * queue 0.
+			 */
+			if (static_priority_end != -1
+			    && (int)queue > static_priority_end
+			    && priority[queue] ==
+			    CVMX_PKO_QUEUE_STATIC_PRIORITY) {
+				cvmx_dprintf("ERROR: cvmx_pko_config_port: "
+					     "Static priority queues aren't "
+					     "contiguous or don't start at "
+					     "base queue. q: %d, eq: %d\n",
+					(int)queue, static_priority_end);
+				return CVMX_PKO_INVALID_PRIORITY;
+			}
+		}
+		if (static_priority_base > 0) {
+			cvmx_dprintf("ERROR: cvmx_pko_config_port: Static "
+				     "priority queues don't start at base "
+				     "queue. sq: %d\n",
+				static_priority_base);
+			return CVMX_PKO_INVALID_PRIORITY;
+		}
+#if 0
+		cvmx_dprintf("Port %d: Static priority queue base: %d, "
+			     "end: %d\n", port,
+			static_priority_base, static_priority_end);
+#endif
+	}
+	/*
+	 * At this point, static_priority_base and static_priority_end
+	 * are either both -1, or are valid start/end queue
+	 * numbers.
+	 */
+
+	result_code = CVMX_PKO_SUCCESS;
+
+#ifdef PKO_DEBUG
+	cvmx_dprintf("num queues: %d (%lld,%lld)\n", num_queues,
+		     CVMX_PKO_QUEUES_PER_PORT_INTERFACE0,
+		     CVMX_PKO_QUEUES_PER_PORT_INTERFACE1);
+#endif
+
+	for (queue = 0; queue < num_queues; queue++) {
+		uint64_t *buf_ptr = NULL;
+
+		config1.u64 = 0;
+		config1.s.idx3 = queue >> 3;
+		config1.s.qid7 = (base_queue + queue) >> 7;
+
+		config.u64 = 0;
+		config.s.tail = queue == (num_queues - 1);
+		config.s.index = queue;
+		config.s.port = port;
+		config.s.queue = base_queue + queue;
+
+		if (!cvmx_octeon_is_pass1()) {
+			config.s.static_p = static_priority_base >= 0;
+			config.s.static_q = (int)queue <= static_priority_end;
+			config.s.s_tail = (int)queue == static_priority_end;
+		}
+		/*
+		 * Convert the priority into an enable bit field. Try
+		 * to space the bits out evenly so the packet don't
+		 * get grouped up
+		 */
+		switch ((int)priority[queue]) {
+		case 0:
+			config.s.qos_mask = 0x00;
+			break;
+		case 1:
+			config.s.qos_mask = 0x01;
+			break;
+		case 2:
+			config.s.qos_mask = 0x11;
+			break;
+		case 3:
+			config.s.qos_mask = 0x49;
+			break;
+		case 4:
+			config.s.qos_mask = 0x55;
+			break;
+		case 5:
+			config.s.qos_mask = 0x57;
+			break;
+		case 6:
+			config.s.qos_mask = 0x77;
+			break;
+		case 7:
+			config.s.qos_mask = 0x7f;
+			break;
+		case 8:
+			config.s.qos_mask = 0xff;
+			break;
+		case CVMX_PKO_QUEUE_STATIC_PRIORITY:
+			if (!cvmx_octeon_is_pass1()) {
+				config.s.qos_mask = 0xff;
+				break;
+			}
+			fallthrough;	/* to the error case, when Pass 1 */
+		default:
+			cvmx_dprintf("ERROR: cvmx_pko_config_port: Invalid "
+				     "priority %llu\n",
+				(unsigned long long)priority[queue]);
+			config.s.qos_mask = 0xff;
+			result_code = CVMX_PKO_INVALID_PRIORITY;
+			break;
+		}
+
+		if (port != CVMX_PKO_MEM_QUEUE_PTRS_ILLEGAL_PID) {
+			cvmx_cmd_queue_result_t cmd_res =
+			    cvmx_cmd_queue_initialize(CVMX_CMD_QUEUE_PKO
+						      (base_queue + queue),
+						      CVMX_PKO_MAX_QUEUE_DEPTH,
+						      CVMX_FPA_OUTPUT_BUFFER_POOL,
+						      CVMX_FPA_OUTPUT_BUFFER_POOL_SIZE
+						      -
+						      CVMX_PKO_COMMAND_BUFFER_SIZE_ADJUST
+						      * 8);
+			if (cmd_res != CVMX_CMD_QUEUE_SUCCESS) {
+				switch (cmd_res) {
+				case CVMX_CMD_QUEUE_NO_MEMORY:
+					cvmx_dprintf("ERROR: "
+						     "cvmx_pko_config_port: "
+						     "Unable to allocate "
+						     "output buffer.\n");
+					return CVMX_PKO_NO_MEMORY;
+				case CVMX_CMD_QUEUE_ALREADY_SETUP:
+					cvmx_dprintf
+					    ("ERROR: cvmx_pko_config_port: Port already setup.\n");
+					return CVMX_PKO_PORT_ALREADY_SETUP;
+				case CVMX_CMD_QUEUE_INVALID_PARAM:
+				default:
+					cvmx_dprintf
+					    ("ERROR: cvmx_pko_config_port: Command queue initialization failed.\n");
+					return CVMX_PKO_CMD_QUEUE_INIT_ERROR;
+				}
+			}
+
+			buf_ptr =
+			    (uint64_t *)
+			    cvmx_cmd_queue_buffer(CVMX_CMD_QUEUE_PKO
+						  (base_queue + queue));
+			config.s.buf_ptr = cvmx_ptr_to_phys(buf_ptr);
+		} else
+			config.s.buf_ptr = 0;
+
+		CVMX_SYNCWS;
+
+		if (!OCTEON_IS_MODEL(OCTEON_CN3XXX))
+			cvmx_write_csr(CVMX_PKO_REG_QUEUE_PTRS1, config1.u64);
+		cvmx_write_csr(CVMX_PKO_MEM_QUEUE_PTRS, config.u64);
+	}
+
+	return result_code;
+}
+
+#ifdef PKO_DEBUG
+/*
+ * Show map of ports -> queues for different cores.
+ */
+void cvmx_pko_show_queue_map()
+{
+	int core, port;
+	int pko_output_ports = 36;
+
+	cvmx_dprintf("port");
+	for (port = 0; port < pko_output_ports; port++)
+		cvmx_dprintf("%3d ", port);
+	cvmx_dprintf("\n");
+
+	for (core = 0; core < CVMX_MAX_CORES; core++) {
+		cvmx_dprintf("\n%2d: ", core);
+		for (port = 0; port < pko_output_ports; port++) {
+			cvmx_dprintf("%3d ",
+				     cvmx_pko_get_base_queue_per_core(port,
+								      core));
+		}
+	}
+	cvmx_dprintf("\n");
+}
+#endif
+
+/*
+ * Rate limit a PKO port to a max packets/sec. This function is only
+ * supported on CN51XX and higher, excluding CN58XX.
+ *
+ * @port:      Port to rate limit
+ * @packets_s: Maximum packet/sec
+ * @burst:     Maximum number of packets to burst in a row before rate
+ *		    limiting cuts in.
+ *
+ * Returns Zero on success, negative on failure
+ */
+int cvmx_pko_rate_limit_packets(int port, int packets_s, int burst)
+{
+	union cvmx_pko_mem_port_rate0 pko_mem_port_rate0;
+	union cvmx_pko_mem_port_rate1 pko_mem_port_rate1;
+
+	pko_mem_port_rate0.u64 = 0;
+	pko_mem_port_rate0.s.pid = port;
+	pko_mem_port_rate0.s.rate_pkt =
+	    cvmx_sysinfo_get()->cpu_clock_hz / packets_s / 16;
+	/* No cost per word since we are limited by packets/sec, not bits/sec */
+	pko_mem_port_rate0.s.rate_word = 0;
+
+	pko_mem_port_rate1.u64 = 0;
+	pko_mem_port_rate1.s.pid = port;
+	pko_mem_port_rate1.s.rate_lim =
+	    ((uint64_t) pko_mem_port_rate0.s.rate_pkt * burst) >> 8;
+
+	cvmx_write_csr(CVMX_PKO_MEM_PORT_RATE0, pko_mem_port_rate0.u64);
+	cvmx_write_csr(CVMX_PKO_MEM_PORT_RATE1, pko_mem_port_rate1.u64);
+	return 0;
+}
+
+/*
+ * Rate limit a PKO port to a max bits/sec. This function is only
+ * supported on CN51XX and higher, excluding CN58XX.
+ *
+ * @port:   Port to rate limit
+ * @bits_s: PKO rate limit in bits/sec
+ * @burst:  Maximum number of bits to burst before rate
+ *		 limiting cuts in.
+ *
+ * Returns Zero on success, negative on failure
+ */
+int cvmx_pko_rate_limit_bits(int port, uint64_t bits_s, int burst)
+{
+	union cvmx_pko_mem_port_rate0 pko_mem_port_rate0;
+	union cvmx_pko_mem_port_rate1 pko_mem_port_rate1;
+	uint64_t clock_rate = cvmx_sysinfo_get()->cpu_clock_hz;
+	uint64_t tokens_per_bit = clock_rate * 16 / bits_s;
+
+	pko_mem_port_rate0.u64 = 0;
+	pko_mem_port_rate0.s.pid = port;
+	/*
+	 * Each packet has a 12 bytes of interframe gap, an 8 byte
+	 * preamble, and a 4 byte CRC. These are not included in the
+	 * per word count. Multiply by 8 to covert to bits and divide
+	 * by 256 for limit granularity.
+	 */
+	pko_mem_port_rate0.s.rate_pkt = (12 + 8 + 4) * 8 * tokens_per_bit / 256;
+	/* Each 8 byte word has 64bits */
+	pko_mem_port_rate0.s.rate_word = 64 * tokens_per_bit;
+
+	pko_mem_port_rate1.u64 = 0;
+	pko_mem_port_rate1.s.pid = port;
+	pko_mem_port_rate1.s.rate_lim = tokens_per_bit * burst / 256;
+
+	cvmx_write_csr(CVMX_PKO_MEM_PORT_RATE0, pko_mem_port_rate0.u64);
+	cvmx_write_csr(CVMX_PKO_MEM_PORT_RATE1, pko_mem_port_rate1.u64);
+	return 0;
+}
diff --git a/arch/mips/cavium-octeon/executive/cvmx-spi.c b/arch/mips/cavium-octeon/executive/cvmx-spi.c
new file mode 100644
index 000000000..eb9333e84
--- /dev/null
+++ b/arch/mips/cavium-octeon/executive/cvmx-spi.c
@@ -0,0 +1,668 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ *
+ * Support library for the SPI
+ */
+#include <asm/octeon/octeon.h>
+
+#include <asm/octeon/cvmx-config.h>
+
+#include <asm/octeon/cvmx-pko.h>
+#include <asm/octeon/cvmx-spi.h>
+
+#include <asm/octeon/cvmx-spxx-defs.h>
+#include <asm/octeon/cvmx-stxx-defs.h>
+#include <asm/octeon/cvmx-srxx-defs.h>
+
+#define INVOKE_CB(function_p, args...)		\
+	do {					\
+		if (function_p) {		\
+			res = function_p(args); \
+			if (res)		\
+				return res;	\
+		}				\
+	} while (0)
+
+#if CVMX_ENABLE_DEBUG_PRINTS
+static const char *modes[] =
+    { "UNKNOWN", "TX Halfplex", "Rx Halfplex", "Duplex" };
+#endif
+
+/* Default callbacks, can be overridden
+ *  using cvmx_spi_get_callbacks/cvmx_spi_set_callbacks
+ */
+static cvmx_spi_callbacks_t cvmx_spi_callbacks = {
+	.reset_cb = cvmx_spi_reset_cb,
+	.calendar_setup_cb = cvmx_spi_calendar_setup_cb,
+	.clock_detect_cb = cvmx_spi_clock_detect_cb,
+	.training_cb = cvmx_spi_training_cb,
+	.calendar_sync_cb = cvmx_spi_calendar_sync_cb,
+	.interface_up_cb = cvmx_spi_interface_up_cb
+};
+
+/*
+ * Get current SPI4 initialization callbacks
+ *
+ * @callbacks:	Pointer to the callbacks structure.to fill
+ *
+ * Returns Pointer to cvmx_spi_callbacks_t structure.
+ */
+void cvmx_spi_get_callbacks(cvmx_spi_callbacks_t *callbacks)
+{
+	memcpy(callbacks, &cvmx_spi_callbacks, sizeof(cvmx_spi_callbacks));
+}
+
+/*
+ * Set new SPI4 initialization callbacks
+ *
+ * @new_callbacks:  Pointer to an updated callbacks structure.
+ */
+void cvmx_spi_set_callbacks(cvmx_spi_callbacks_t *new_callbacks)
+{
+	memcpy(&cvmx_spi_callbacks, new_callbacks, sizeof(cvmx_spi_callbacks));
+}
+
+/*
+ * Initialize and start the SPI interface.
+ *
+ * @interface: The identifier of the packet interface to configure and
+ *		    use as a SPI interface.
+ * @mode:      The operating mode for the SPI interface. The interface
+ *		    can operate as a full duplex (both Tx and Rx data paths
+ *		    active) or as a halfplex (either the Tx data path is
+ *		    active or the Rx data path is active, but not both).
+ * @timeout:   Timeout to wait for clock synchronization in seconds
+ * @num_ports: Number of SPI ports to configure
+ *
+ * Returns Zero on success, negative of failure.
+ */
+int cvmx_spi_start_interface(int interface, cvmx_spi_mode_t mode, int timeout,
+			     int num_ports)
+{
+	int res = -1;
+
+	if (!(OCTEON_IS_MODEL(OCTEON_CN38XX) || OCTEON_IS_MODEL(OCTEON_CN58XX)))
+		return res;
+
+	/* Callback to perform SPI4 reset */
+	INVOKE_CB(cvmx_spi_callbacks.reset_cb, interface, mode);
+
+	/* Callback to perform calendar setup */
+	INVOKE_CB(cvmx_spi_callbacks.calendar_setup_cb, interface, mode,
+		  num_ports);
+
+	/* Callback to perform clock detection */
+	INVOKE_CB(cvmx_spi_callbacks.clock_detect_cb, interface, mode, timeout);
+
+	/* Callback to perform SPI4 link training */
+	INVOKE_CB(cvmx_spi_callbacks.training_cb, interface, mode, timeout);
+
+	/* Callback to perform calendar sync */
+	INVOKE_CB(cvmx_spi_callbacks.calendar_sync_cb, interface, mode,
+		  timeout);
+
+	/* Callback to handle interface coming up */
+	INVOKE_CB(cvmx_spi_callbacks.interface_up_cb, interface, mode);
+
+	return res;
+}
+
+/*
+ * This routine restarts the SPI interface after it has lost synchronization
+ * with its correspondent system.
+ *
+ * @interface: The identifier of the packet interface to configure and
+ *		    use as a SPI interface.
+ * @mode:      The operating mode for the SPI interface. The interface
+ *		    can operate as a full duplex (both Tx and Rx data paths
+ *		    active) or as a halfplex (either the Tx data path is
+ *		    active or the Rx data path is active, but not both).
+ * @timeout:   Timeout to wait for clock synchronization in seconds
+ *
+ * Returns Zero on success, negative of failure.
+ */
+int cvmx_spi_restart_interface(int interface, cvmx_spi_mode_t mode, int timeout)
+{
+	int res = -1;
+
+	if (!(OCTEON_IS_MODEL(OCTEON_CN38XX) || OCTEON_IS_MODEL(OCTEON_CN58XX)))
+		return res;
+
+	cvmx_dprintf("SPI%d: Restart %s\n", interface, modes[mode]);
+
+	/* Callback to perform SPI4 reset */
+	INVOKE_CB(cvmx_spi_callbacks.reset_cb, interface, mode);
+
+	/* NOTE: Calendar setup is not performed during restart */
+	/*	 Refer to cvmx_spi_start_interface() for the full sequence */
+
+	/* Callback to perform clock detection */
+	INVOKE_CB(cvmx_spi_callbacks.clock_detect_cb, interface, mode, timeout);
+
+	/* Callback to perform SPI4 link training */
+	INVOKE_CB(cvmx_spi_callbacks.training_cb, interface, mode, timeout);
+
+	/* Callback to perform calendar sync */
+	INVOKE_CB(cvmx_spi_callbacks.calendar_sync_cb, interface, mode,
+		  timeout);
+
+	/* Callback to handle interface coming up */
+	INVOKE_CB(cvmx_spi_callbacks.interface_up_cb, interface, mode);
+
+	return res;
+}
+EXPORT_SYMBOL_GPL(cvmx_spi_restart_interface);
+
+/*
+ * Callback to perform SPI4 reset
+ *
+ * @interface: The identifier of the packet interface to configure and
+ *		    use as a SPI interface.
+ * @mode:      The operating mode for the SPI interface. The interface
+ *		    can operate as a full duplex (both Tx and Rx data paths
+ *		    active) or as a halfplex (either the Tx data path is
+ *		    active or the Rx data path is active, but not both).
+ *
+ * Returns Zero on success, non-zero error code on failure (will cause
+ * SPI initialization to abort)
+ */
+int cvmx_spi_reset_cb(int interface, cvmx_spi_mode_t mode)
+{
+	union cvmx_spxx_dbg_deskew_ctl spxx_dbg_deskew_ctl;
+	union cvmx_spxx_clk_ctl spxx_clk_ctl;
+	union cvmx_spxx_bist_stat spxx_bist_stat;
+	union cvmx_spxx_int_msk spxx_int_msk;
+	union cvmx_stxx_int_msk stxx_int_msk;
+	union cvmx_spxx_trn4_ctl spxx_trn4_ctl;
+	int index;
+	uint64_t MS = cvmx_sysinfo_get()->cpu_clock_hz / 1000;
+
+	/* Disable SPI error events while we run BIST */
+	spxx_int_msk.u64 = cvmx_read_csr(CVMX_SPXX_INT_MSK(interface));
+	cvmx_write_csr(CVMX_SPXX_INT_MSK(interface), 0);
+	stxx_int_msk.u64 = cvmx_read_csr(CVMX_STXX_INT_MSK(interface));
+	cvmx_write_csr(CVMX_STXX_INT_MSK(interface), 0);
+
+	/* Run BIST in the SPI interface */
+	cvmx_write_csr(CVMX_SRXX_COM_CTL(interface), 0);
+	cvmx_write_csr(CVMX_STXX_COM_CTL(interface), 0);
+	spxx_clk_ctl.u64 = 0;
+	spxx_clk_ctl.s.runbist = 1;
+	cvmx_write_csr(CVMX_SPXX_CLK_CTL(interface), spxx_clk_ctl.u64);
+	__delay(10 * MS);
+	spxx_bist_stat.u64 = cvmx_read_csr(CVMX_SPXX_BIST_STAT(interface));
+	if (spxx_bist_stat.s.stat0)
+		cvmx_dprintf
+		    ("ERROR SPI%d: BIST failed on receive datapath FIFO\n",
+		     interface);
+	if (spxx_bist_stat.s.stat1)
+		cvmx_dprintf("ERROR SPI%d: BIST failed on RX calendar table\n",
+			     interface);
+	if (spxx_bist_stat.s.stat2)
+		cvmx_dprintf("ERROR SPI%d: BIST failed on TX calendar table\n",
+			     interface);
+
+	/* Clear the calendar table after BIST to fix parity errors */
+	for (index = 0; index < 32; index++) {
+		union cvmx_srxx_spi4_calx srxx_spi4_calx;
+		union cvmx_stxx_spi4_calx stxx_spi4_calx;
+
+		srxx_spi4_calx.u64 = 0;
+		srxx_spi4_calx.s.oddpar = 1;
+		cvmx_write_csr(CVMX_SRXX_SPI4_CALX(index, interface),
+			       srxx_spi4_calx.u64);
+
+		stxx_spi4_calx.u64 = 0;
+		stxx_spi4_calx.s.oddpar = 1;
+		cvmx_write_csr(CVMX_STXX_SPI4_CALX(index, interface),
+			       stxx_spi4_calx.u64);
+	}
+
+	/* Re enable reporting of error interrupts */
+	cvmx_write_csr(CVMX_SPXX_INT_REG(interface),
+		       cvmx_read_csr(CVMX_SPXX_INT_REG(interface)));
+	cvmx_write_csr(CVMX_SPXX_INT_MSK(interface), spxx_int_msk.u64);
+	cvmx_write_csr(CVMX_STXX_INT_REG(interface),
+		       cvmx_read_csr(CVMX_STXX_INT_REG(interface)));
+	cvmx_write_csr(CVMX_STXX_INT_MSK(interface), stxx_int_msk.u64);
+
+	/* Setup the CLKDLY right in the middle */
+	spxx_clk_ctl.u64 = 0;
+	spxx_clk_ctl.s.seetrn = 0;
+	spxx_clk_ctl.s.clkdly = 0x10;
+	spxx_clk_ctl.s.runbist = 0;
+	spxx_clk_ctl.s.statdrv = 0;
+	/* This should always be on the opposite edge as statdrv */
+	spxx_clk_ctl.s.statrcv = 1;
+	spxx_clk_ctl.s.sndtrn = 0;
+	spxx_clk_ctl.s.drptrn = 0;
+	spxx_clk_ctl.s.rcvtrn = 0;
+	spxx_clk_ctl.s.srxdlck = 0;
+	cvmx_write_csr(CVMX_SPXX_CLK_CTL(interface), spxx_clk_ctl.u64);
+	__delay(100 * MS);
+
+	/* Reset SRX0 DLL */
+	spxx_clk_ctl.s.srxdlck = 1;
+	cvmx_write_csr(CVMX_SPXX_CLK_CTL(interface), spxx_clk_ctl.u64);
+
+	/* Waiting for Inf0 Spi4 RX DLL to lock */
+	__delay(100 * MS);
+
+	/* Enable dynamic alignment */
+	spxx_trn4_ctl.s.trntest = 0;
+	spxx_trn4_ctl.s.jitter = 1;
+	spxx_trn4_ctl.s.clr_boot = 1;
+	spxx_trn4_ctl.s.set_boot = 0;
+	if (OCTEON_IS_MODEL(OCTEON_CN58XX))
+		spxx_trn4_ctl.s.maxdist = 3;
+	else
+		spxx_trn4_ctl.s.maxdist = 8;
+	spxx_trn4_ctl.s.macro_en = 1;
+	spxx_trn4_ctl.s.mux_en = 1;
+	cvmx_write_csr(CVMX_SPXX_TRN4_CTL(interface), spxx_trn4_ctl.u64);
+
+	spxx_dbg_deskew_ctl.u64 = 0;
+	cvmx_write_csr(CVMX_SPXX_DBG_DESKEW_CTL(interface),
+		       spxx_dbg_deskew_ctl.u64);
+
+	return 0;
+}
+
+/*
+ * Callback to setup calendar and miscellaneous settings before clock detection
+ *
+ * @interface: The identifier of the packet interface to configure and
+ *		    use as a SPI interface.
+ * @mode:      The operating mode for the SPI interface. The interface
+ *		    can operate as a full duplex (both Tx and Rx data paths
+ *		    active) or as a halfplex (either the Tx data path is
+ *		    active or the Rx data path is active, but not both).
+ * @num_ports: Number of ports to configure on SPI
+ *
+ * Returns Zero on success, non-zero error code on failure (will cause
+ * SPI initialization to abort)
+ */
+int cvmx_spi_calendar_setup_cb(int interface, cvmx_spi_mode_t mode,
+			       int num_ports)
+{
+	int port;
+	int index;
+	if (mode & CVMX_SPI_MODE_RX_HALFPLEX) {
+		union cvmx_srxx_com_ctl srxx_com_ctl;
+		union cvmx_srxx_spi4_stat srxx_spi4_stat;
+
+		/* SRX0 number of Ports */
+		srxx_com_ctl.u64 = 0;
+		srxx_com_ctl.s.prts = num_ports - 1;
+		srxx_com_ctl.s.st_en = 0;
+		srxx_com_ctl.s.inf_en = 0;
+		cvmx_write_csr(CVMX_SRXX_COM_CTL(interface), srxx_com_ctl.u64);
+
+		/* SRX0 Calendar Table. This round robbins through all ports */
+		port = 0;
+		index = 0;
+		while (port < num_ports) {
+			union cvmx_srxx_spi4_calx srxx_spi4_calx;
+			srxx_spi4_calx.u64 = 0;
+			srxx_spi4_calx.s.prt0 = port++;
+			srxx_spi4_calx.s.prt1 = port++;
+			srxx_spi4_calx.s.prt2 = port++;
+			srxx_spi4_calx.s.prt3 = port++;
+			srxx_spi4_calx.s.oddpar =
+			    ~(cvmx_dpop(srxx_spi4_calx.u64) & 1);
+			cvmx_write_csr(CVMX_SRXX_SPI4_CALX(index, interface),
+				       srxx_spi4_calx.u64);
+			index++;
+		}
+		srxx_spi4_stat.u64 = 0;
+		srxx_spi4_stat.s.len = num_ports;
+		srxx_spi4_stat.s.m = 1;
+		cvmx_write_csr(CVMX_SRXX_SPI4_STAT(interface),
+			       srxx_spi4_stat.u64);
+	}
+
+	if (mode & CVMX_SPI_MODE_TX_HALFPLEX) {
+		union cvmx_stxx_arb_ctl stxx_arb_ctl;
+		union cvmx_gmxx_tx_spi_max gmxx_tx_spi_max;
+		union cvmx_gmxx_tx_spi_thresh gmxx_tx_spi_thresh;
+		union cvmx_gmxx_tx_spi_ctl gmxx_tx_spi_ctl;
+		union cvmx_stxx_spi4_stat stxx_spi4_stat;
+		union cvmx_stxx_spi4_dat stxx_spi4_dat;
+
+		/* STX0 Config */
+		stxx_arb_ctl.u64 = 0;
+		stxx_arb_ctl.s.igntpa = 0;
+		stxx_arb_ctl.s.mintrn = 0;
+		cvmx_write_csr(CVMX_STXX_ARB_CTL(interface), stxx_arb_ctl.u64);
+
+		gmxx_tx_spi_max.u64 = 0;
+		gmxx_tx_spi_max.s.max1 = 8;
+		gmxx_tx_spi_max.s.max2 = 4;
+		gmxx_tx_spi_max.s.slice = 0;
+		cvmx_write_csr(CVMX_GMXX_TX_SPI_MAX(interface),
+			       gmxx_tx_spi_max.u64);
+
+		gmxx_tx_spi_thresh.u64 = 0;
+		gmxx_tx_spi_thresh.s.thresh = 4;
+		cvmx_write_csr(CVMX_GMXX_TX_SPI_THRESH(interface),
+			       gmxx_tx_spi_thresh.u64);
+
+		gmxx_tx_spi_ctl.u64 = 0;
+		gmxx_tx_spi_ctl.s.tpa_clr = 0;
+		gmxx_tx_spi_ctl.s.cont_pkt = 0;
+		cvmx_write_csr(CVMX_GMXX_TX_SPI_CTL(interface),
+			       gmxx_tx_spi_ctl.u64);
+
+		/* STX0 Training Control */
+		stxx_spi4_dat.u64 = 0;
+		/*Minimum needed by dynamic alignment */
+		stxx_spi4_dat.s.alpha = 32;
+		stxx_spi4_dat.s.max_t = 0xFFFF; /*Minimum interval is 0x20 */
+		cvmx_write_csr(CVMX_STXX_SPI4_DAT(interface),
+			       stxx_spi4_dat.u64);
+
+		/* STX0 Calendar Table. This round robbins through all ports */
+		port = 0;
+		index = 0;
+		while (port < num_ports) {
+			union cvmx_stxx_spi4_calx stxx_spi4_calx;
+			stxx_spi4_calx.u64 = 0;
+			stxx_spi4_calx.s.prt0 = port++;
+			stxx_spi4_calx.s.prt1 = port++;
+			stxx_spi4_calx.s.prt2 = port++;
+			stxx_spi4_calx.s.prt3 = port++;
+			stxx_spi4_calx.s.oddpar =
+			    ~(cvmx_dpop(stxx_spi4_calx.u64) & 1);
+			cvmx_write_csr(CVMX_STXX_SPI4_CALX(index, interface),
+				       stxx_spi4_calx.u64);
+			index++;
+		}
+		stxx_spi4_stat.u64 = 0;
+		stxx_spi4_stat.s.len = num_ports;
+		stxx_spi4_stat.s.m = 1;
+		cvmx_write_csr(CVMX_STXX_SPI4_STAT(interface),
+			       stxx_spi4_stat.u64);
+	}
+
+	return 0;
+}
+
+/*
+ * Callback to perform clock detection
+ *
+ * @interface: The identifier of the packet interface to configure and
+ *		    use as a SPI interface.
+ * @mode:      The operating mode for the SPI interface. The interface
+ *		    can operate as a full duplex (both Tx and Rx data paths
+ *		    active) or as a halfplex (either the Tx data path is
+ *		    active or the Rx data path is active, but not both).
+ * @timeout:   Timeout to wait for clock synchronization in seconds
+ *
+ * Returns Zero on success, non-zero error code on failure (will cause
+ * SPI initialization to abort)
+ */
+int cvmx_spi_clock_detect_cb(int interface, cvmx_spi_mode_t mode, int timeout)
+{
+	int clock_transitions;
+	union cvmx_spxx_clk_stat stat;
+	uint64_t timeout_time;
+	uint64_t MS = cvmx_sysinfo_get()->cpu_clock_hz / 1000;
+
+	/*
+	 * Regardless of operating mode, both Tx and Rx clocks must be
+	 * present for the SPI interface to operate.
+	 */
+	cvmx_dprintf("SPI%d: Waiting to see TsClk...\n", interface);
+	timeout_time = cvmx_get_cycle() + 1000ull * MS * timeout;
+	/*
+	 * Require 100 clock transitions in order to avoid any noise
+	 * in the beginning.
+	 */
+	clock_transitions = 100;
+	do {
+		stat.u64 = cvmx_read_csr(CVMX_SPXX_CLK_STAT(interface));
+		if (stat.s.s4clk0 && stat.s.s4clk1 && clock_transitions) {
+			/*
+			 * We've seen a clock transition, so decrement
+			 * the number we still need.
+			 */
+			clock_transitions--;
+			cvmx_write_csr(CVMX_SPXX_CLK_STAT(interface), stat.u64);
+			stat.s.s4clk0 = 0;
+			stat.s.s4clk1 = 0;
+		}
+		if (cvmx_get_cycle() > timeout_time) {
+			cvmx_dprintf("SPI%d: Timeout\n", interface);
+			return -1;
+		}
+	} while (stat.s.s4clk0 == 0 || stat.s.s4clk1 == 0);
+
+	cvmx_dprintf("SPI%d: Waiting to see RsClk...\n", interface);
+	timeout_time = cvmx_get_cycle() + 1000ull * MS * timeout;
+	/*
+	 * Require 100 clock transitions in order to avoid any noise in the
+	 * beginning.
+	 */
+	clock_transitions = 100;
+	do {
+		stat.u64 = cvmx_read_csr(CVMX_SPXX_CLK_STAT(interface));
+		if (stat.s.d4clk0 && stat.s.d4clk1 && clock_transitions) {
+			/*
+			 * We've seen a clock transition, so decrement
+			 * the number we still need
+			 */
+			clock_transitions--;
+			cvmx_write_csr(CVMX_SPXX_CLK_STAT(interface), stat.u64);
+			stat.s.d4clk0 = 0;
+			stat.s.d4clk1 = 0;
+		}
+		if (cvmx_get_cycle() > timeout_time) {
+			cvmx_dprintf("SPI%d: Timeout\n", interface);
+			return -1;
+		}
+	} while (stat.s.d4clk0 == 0 || stat.s.d4clk1 == 0);
+
+	return 0;
+}
+
+/*
+ * Callback to perform link training
+ *
+ * @interface: The identifier of the packet interface to configure and
+ *		    use as a SPI interface.
+ * @mode:      The operating mode for the SPI interface. The interface
+ *		    can operate as a full duplex (both Tx and Rx data paths
+ *		    active) or as a halfplex (either the Tx data path is
+ *		    active or the Rx data path is active, but not both).
+ * @timeout:   Timeout to wait for link to be trained (in seconds)
+ *
+ * Returns Zero on success, non-zero error code on failure (will cause
+ * SPI initialization to abort)
+ */
+int cvmx_spi_training_cb(int interface, cvmx_spi_mode_t mode, int timeout)
+{
+	union cvmx_spxx_trn4_ctl spxx_trn4_ctl;
+	union cvmx_spxx_clk_stat stat;
+	uint64_t MS = cvmx_sysinfo_get()->cpu_clock_hz / 1000;
+	uint64_t timeout_time = cvmx_get_cycle() + 1000ull * MS * timeout;
+	int rx_training_needed;
+
+	/* SRX0 & STX0 Inf0 Links are configured - begin training */
+	union cvmx_spxx_clk_ctl spxx_clk_ctl;
+	spxx_clk_ctl.u64 = 0;
+	spxx_clk_ctl.s.seetrn = 0;
+	spxx_clk_ctl.s.clkdly = 0x10;
+	spxx_clk_ctl.s.runbist = 0;
+	spxx_clk_ctl.s.statdrv = 0;
+	/* This should always be on the opposite edge as statdrv */
+	spxx_clk_ctl.s.statrcv = 1;
+	spxx_clk_ctl.s.sndtrn = 1;
+	spxx_clk_ctl.s.drptrn = 1;
+	spxx_clk_ctl.s.rcvtrn = 1;
+	spxx_clk_ctl.s.srxdlck = 1;
+	cvmx_write_csr(CVMX_SPXX_CLK_CTL(interface), spxx_clk_ctl.u64);
+	__delay(1000 * MS);
+
+	/* SRX0 clear the boot bit */
+	spxx_trn4_ctl.u64 = cvmx_read_csr(CVMX_SPXX_TRN4_CTL(interface));
+	spxx_trn4_ctl.s.clr_boot = 1;
+	cvmx_write_csr(CVMX_SPXX_TRN4_CTL(interface), spxx_trn4_ctl.u64);
+
+	/* Wait for the training sequence to complete */
+	cvmx_dprintf("SPI%d: Waiting for training\n", interface);
+	__delay(1000 * MS);
+	/* Wait a really long time here */
+	timeout_time = cvmx_get_cycle() + 1000ull * MS * 600;
+	/*
+	 * The HRM says we must wait for 34 + 16 * MAXDIST training sequences.
+	 * We'll be pessimistic and wait for a lot more.
+	 */
+	rx_training_needed = 500;
+	do {
+		stat.u64 = cvmx_read_csr(CVMX_SPXX_CLK_STAT(interface));
+		if (stat.s.srxtrn && rx_training_needed) {
+			rx_training_needed--;
+			cvmx_write_csr(CVMX_SPXX_CLK_STAT(interface), stat.u64);
+			stat.s.srxtrn = 0;
+		}
+		if (cvmx_get_cycle() > timeout_time) {
+			cvmx_dprintf("SPI%d: Timeout\n", interface);
+			return -1;
+		}
+	} while (stat.s.srxtrn == 0);
+
+	return 0;
+}
+
+/*
+ * Callback to perform calendar data synchronization
+ *
+ * @interface: The identifier of the packet interface to configure and
+ *		    use as a SPI interface.
+ * @mode:      The operating mode for the SPI interface. The interface
+ *		    can operate as a full duplex (both Tx and Rx data paths
+ *		    active) or as a halfplex (either the Tx data path is
+ *		    active or the Rx data path is active, but not both).
+ * @timeout:   Timeout to wait for calendar data in seconds
+ *
+ * Returns Zero on success, non-zero error code on failure (will cause
+ * SPI initialization to abort)
+ */
+int cvmx_spi_calendar_sync_cb(int interface, cvmx_spi_mode_t mode, int timeout)
+{
+	uint64_t MS = cvmx_sysinfo_get()->cpu_clock_hz / 1000;
+	if (mode & CVMX_SPI_MODE_RX_HALFPLEX) {
+		/* SRX0 interface should be good, send calendar data */
+		union cvmx_srxx_com_ctl srxx_com_ctl;
+		cvmx_dprintf
+		    ("SPI%d: Rx is synchronized, start sending calendar data\n",
+		     interface);
+		srxx_com_ctl.u64 = cvmx_read_csr(CVMX_SRXX_COM_CTL(interface));
+		srxx_com_ctl.s.inf_en = 1;
+		srxx_com_ctl.s.st_en = 1;
+		cvmx_write_csr(CVMX_SRXX_COM_CTL(interface), srxx_com_ctl.u64);
+	}
+
+	if (mode & CVMX_SPI_MODE_TX_HALFPLEX) {
+		/* STX0 has achieved sync */
+		/* The corespondant board should be sending calendar data */
+		/* Enable the STX0 STAT receiver. */
+		union cvmx_spxx_clk_stat stat;
+		uint64_t timeout_time;
+		union cvmx_stxx_com_ctl stxx_com_ctl;
+		stxx_com_ctl.u64 = 0;
+		stxx_com_ctl.s.st_en = 1;
+		cvmx_write_csr(CVMX_STXX_COM_CTL(interface), stxx_com_ctl.u64);
+
+		/* Waiting for calendar sync on STX0 STAT */
+		cvmx_dprintf("SPI%d: Waiting to sync on STX[%d] STAT\n",
+			     interface, interface);
+		timeout_time = cvmx_get_cycle() + 1000ull * MS * timeout;
+		/* SPX0_CLK_STAT - SPX0_CLK_STAT[STXCAL] should be 1 (bit10) */
+		do {
+			stat.u64 = cvmx_read_csr(CVMX_SPXX_CLK_STAT(interface));
+			if (cvmx_get_cycle() > timeout_time) {
+				cvmx_dprintf("SPI%d: Timeout\n", interface);
+				return -1;
+			}
+		} while (stat.s.stxcal == 0);
+	}
+
+	return 0;
+}
+
+/*
+ * Callback to handle interface up
+ *
+ * @interface: The identifier of the packet interface to configure and
+ *		    use as a SPI interface.
+ * @mode:      The operating mode for the SPI interface. The interface
+ *		    can operate as a full duplex (both Tx and Rx data paths
+ *		    active) or as a halfplex (either the Tx data path is
+ *		    active or the Rx data path is active, but not both).
+ *
+ * Returns Zero on success, non-zero error code on failure (will cause
+ * SPI initialization to abort)
+ */
+int cvmx_spi_interface_up_cb(int interface, cvmx_spi_mode_t mode)
+{
+	union cvmx_gmxx_rxx_frm_min gmxx_rxx_frm_min;
+	union cvmx_gmxx_rxx_frm_max gmxx_rxx_frm_max;
+	union cvmx_gmxx_rxx_jabber gmxx_rxx_jabber;
+
+	if (mode & CVMX_SPI_MODE_RX_HALFPLEX) {
+		union cvmx_srxx_com_ctl srxx_com_ctl;
+		srxx_com_ctl.u64 = cvmx_read_csr(CVMX_SRXX_COM_CTL(interface));
+		srxx_com_ctl.s.inf_en = 1;
+		cvmx_write_csr(CVMX_SRXX_COM_CTL(interface), srxx_com_ctl.u64);
+		cvmx_dprintf("SPI%d: Rx is now up\n", interface);
+	}
+
+	if (mode & CVMX_SPI_MODE_TX_HALFPLEX) {
+		union cvmx_stxx_com_ctl stxx_com_ctl;
+		stxx_com_ctl.u64 = cvmx_read_csr(CVMX_STXX_COM_CTL(interface));
+		stxx_com_ctl.s.inf_en = 1;
+		cvmx_write_csr(CVMX_STXX_COM_CTL(interface), stxx_com_ctl.u64);
+		cvmx_dprintf("SPI%d: Tx is now up\n", interface);
+	}
+
+	gmxx_rxx_frm_min.u64 = 0;
+	gmxx_rxx_frm_min.s.len = 64;
+	cvmx_write_csr(CVMX_GMXX_RXX_FRM_MIN(0, interface),
+		       gmxx_rxx_frm_min.u64);
+	gmxx_rxx_frm_max.u64 = 0;
+	gmxx_rxx_frm_max.s.len = 64 * 1024 - 4;
+	cvmx_write_csr(CVMX_GMXX_RXX_FRM_MAX(0, interface),
+		       gmxx_rxx_frm_max.u64);
+	gmxx_rxx_jabber.u64 = 0;
+	gmxx_rxx_jabber.s.cnt = 64 * 1024 - 4;
+	cvmx_write_csr(CVMX_GMXX_RXX_JABBER(0, interface), gmxx_rxx_jabber.u64);
+
+	return 0;
+}
diff --git a/arch/mips/cavium-octeon/executive/cvmx-sysinfo.c b/arch/mips/cavium-octeon/executive/cvmx-sysinfo.c
new file mode 100644
index 000000000..30ecba134
--- /dev/null
+++ b/arch/mips/cavium-octeon/executive/cvmx-sysinfo.c
@@ -0,0 +1,53 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ * This module provides system/board/application information obtained
+ * by the bootloader.
+ */
+#include <linux/export.h>
+
+#include <asm/octeon/cvmx.h>
+#include <asm/octeon/cvmx-sysinfo.h>
+
+/*
+ * This structure defines the private state maintained by sysinfo module.
+ */
+static struct cvmx_sysinfo sysinfo;	   /* system information */
+
+/*
+ * Returns the application information as obtained
+ * by the bootloader.  This provides the core mask of the cores
+ * running the same application image, as well as the physical
+ * memory regions available to the core.
+ */
+struct cvmx_sysinfo *cvmx_sysinfo_get(void)
+{
+	return &sysinfo;
+}
+EXPORT_SYMBOL(cvmx_sysinfo_get);
+
diff --git a/arch/mips/cavium-octeon/executive/octeon-model.c b/arch/mips/cavium-octeon/executive/octeon-model.c
new file mode 100644
index 000000000..657dbad96
--- /dev/null
+++ b/arch/mips/cavium-octeon/executive/octeon-model.c
@@ -0,0 +1,511 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2017 Cavium, Inc.
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#include <asm/octeon/octeon.h>
+
+enum octeon_feature_bits __octeon_feature_bits __read_mostly;
+EXPORT_SYMBOL_GPL(__octeon_feature_bits);
+
+/**
+ * Read a byte of fuse data
+ * @byte_addr:	 address to read
+ *
+ * Returns fuse value: 0 or 1
+ */
+static uint8_t __init cvmx_fuse_read_byte(int byte_addr)
+{
+	union cvmx_mio_fus_rcmd read_cmd;
+
+	read_cmd.u64 = 0;
+	read_cmd.s.addr = byte_addr;
+	read_cmd.s.pend = 1;
+	cvmx_write_csr(CVMX_MIO_FUS_RCMD, read_cmd.u64);
+	while ((read_cmd.u64 = cvmx_read_csr(CVMX_MIO_FUS_RCMD))
+	       && read_cmd.s.pend)
+		;
+	return read_cmd.s.dat;
+}
+
+/*
+ * Version of octeon_model_get_string() that takes buffer as argument,
+ * as running early in u-boot static/global variables don't work when
+ * running from flash.
+ */
+static const char *__init octeon_model_get_string_buffer(uint32_t chip_id,
+							 char *buffer)
+{
+	const char *family;
+	const char *core_model;
+	char pass[4];
+	int clock_mhz;
+	const char *suffix;
+	int num_cores;
+	union cvmx_mio_fus_dat2 fus_dat2;
+	union cvmx_mio_fus_dat3 fus_dat3;
+	char fuse_model[10];
+	uint32_t fuse_data = 0;
+	uint64_t l2d_fus3 = 0;
+
+	if (OCTEON_IS_MODEL(OCTEON_CN3XXX) || OCTEON_IS_MODEL(OCTEON_CN5XXX))
+		l2d_fus3 = (cvmx_read_csr(CVMX_L2D_FUS3) >> 34) & 0x3;
+	fus_dat2.u64 = cvmx_read_csr(CVMX_MIO_FUS_DAT2);
+	fus_dat3.u64 = cvmx_read_csr(CVMX_MIO_FUS_DAT3);
+	num_cores = cvmx_octeon_num_cores();
+
+	/* Make sure the non existent devices look disabled */
+	switch ((chip_id >> 8) & 0xff) {
+	case 6:		/* CN50XX */
+	case 2:		/* CN30XX */
+		fus_dat3.s.nodfa_dte = 1;
+		fus_dat3.s.nozip = 1;
+		break;
+	case 4:		/* CN57XX or CN56XX */
+		fus_dat3.s.nodfa_dte = 1;
+		break;
+	default:
+		break;
+	}
+
+	/* Make a guess at the suffix */
+	/* NSP = everything */
+	/* EXP = No crypto */
+	/* SCP = No DFA, No zip */
+	/* CP = No DFA, No crypto, No zip */
+	if (fus_dat3.s.nodfa_dte) {
+		if (fus_dat2.s.nocrypto)
+			suffix = "CP";
+		else
+			suffix = "SCP";
+	} else if (fus_dat2.s.nocrypto)
+		suffix = "EXP";
+	else
+		suffix = "NSP";
+
+	if (!fus_dat2.s.nocrypto)
+		__octeon_feature_bits |= OCTEON_HAS_CRYPTO;
+
+	/*
+	 * Assume pass number is encoded using <5:3><2:0>. Exceptions
+	 * will be fixed later.
+	 */
+	sprintf(pass, "%d.%d", (int)((chip_id >> 3) & 7) + 1, (int)chip_id & 7);
+
+	/*
+	 * Use the number of cores to determine the last 2 digits of
+	 * the model number. There are some exceptions that are fixed
+	 * later.
+	 */
+	switch (num_cores) {
+	case 48:
+		core_model = "90";
+		break;
+	case 44:
+		core_model = "88";
+		break;
+	case 40:
+		core_model = "85";
+		break;
+	case 32:
+		core_model = "80";
+		break;
+	case 24:
+		core_model = "70";
+		break;
+	case 16:
+		core_model = "60";
+		break;
+	case 15:
+		core_model = "58";
+		break;
+	case 14:
+		core_model = "55";
+		break;
+	case 13:
+		core_model = "52";
+		break;
+	case 12:
+		core_model = "50";
+		break;
+	case 11:
+		core_model = "48";
+		break;
+	case 10:
+		core_model = "45";
+		break;
+	case 9:
+		core_model = "42";
+		break;
+	case 8:
+		core_model = "40";
+		break;
+	case 7:
+		core_model = "38";
+		break;
+	case 6:
+		core_model = "34";
+		break;
+	case 5:
+		core_model = "32";
+		break;
+	case 4:
+		core_model = "30";
+		break;
+	case 3:
+		core_model = "25";
+		break;
+	case 2:
+		core_model = "20";
+		break;
+	case 1:
+		core_model = "10";
+		break;
+	default:
+		core_model = "XX";
+		break;
+	}
+
+	/* Now figure out the family, the first two digits */
+	switch ((chip_id >> 8) & 0xff) {
+	case 0:		/* CN38XX, CN37XX or CN36XX */
+		if (l2d_fus3) {
+			/*
+			 * For some unknown reason, the 16 core one is
+			 * called 37 instead of 36.
+			 */
+			if (num_cores >= 16)
+				family = "37";
+			else
+				family = "36";
+		} else
+			family = "38";
+		/*
+		 * This series of chips didn't follow the standard
+		 * pass numbering.
+		 */
+		switch (chip_id & 0xf) {
+		case 0:
+			strcpy(pass, "1.X");
+			break;
+		case 1:
+			strcpy(pass, "2.X");
+			break;
+		case 3:
+			strcpy(pass, "3.X");
+			break;
+		default:
+			strcpy(pass, "X.X");
+			break;
+		}
+		break;
+	case 1:		/* CN31XX or CN3020 */
+		if ((chip_id & 0x10) || l2d_fus3)
+			family = "30";
+		else
+			family = "31";
+		/*
+		 * This series of chips didn't follow the standard
+		 * pass numbering.
+		 */
+		switch (chip_id & 0xf) {
+		case 0:
+			strcpy(pass, "1.0");
+			break;
+		case 2:
+			strcpy(pass, "1.1");
+			break;
+		default:
+			strcpy(pass, "X.X");
+			break;
+		}
+		break;
+	case 2:		/* CN3010 or CN3005 */
+		family = "30";
+		/* A chip with half cache is an 05 */
+		if (l2d_fus3)
+			core_model = "05";
+		/*
+		 * This series of chips didn't follow the standard
+		 * pass numbering.
+		 */
+		switch (chip_id & 0xf) {
+		case 0:
+			strcpy(pass, "1.0");
+			break;
+		case 2:
+			strcpy(pass, "1.1");
+			break;
+		default:
+			strcpy(pass, "X.X");
+			break;
+		}
+		break;
+	case 3:		/* CN58XX */
+		family = "58";
+		/* Special case. 4 core, half cache (CP with half cache) */
+		if ((num_cores == 4) && l2d_fus3 && !strncmp(suffix, "CP", 2))
+			core_model = "29";
+
+		/* Pass 1 uses different encodings for pass numbers */
+		if ((chip_id & 0xFF) < 0x8) {
+			switch (chip_id & 0x3) {
+			case 0:
+				strcpy(pass, "1.0");
+				break;
+			case 1:
+				strcpy(pass, "1.1");
+				break;
+			case 3:
+				strcpy(pass, "1.2");
+				break;
+			default:
+				strcpy(pass, "1.X");
+				break;
+			}
+		}
+		break;
+	case 4:		/* CN57XX, CN56XX, CN55XX, CN54XX */
+		if (fus_dat2.cn56xx.raid_en) {
+			if (l2d_fus3)
+				family = "55";
+			else
+				family = "57";
+			if (fus_dat2.cn56xx.nocrypto)
+				suffix = "SP";
+			else
+				suffix = "SSP";
+		} else {
+			if (fus_dat2.cn56xx.nocrypto)
+				suffix = "CP";
+			else {
+				suffix = "NSP";
+				if (fus_dat3.s.nozip)
+					suffix = "SCP";
+
+				if (fus_dat3.cn38xx.bar2_en)
+					suffix = "NSPB2";
+			}
+			if (l2d_fus3)
+				family = "54";
+			else
+				family = "56";
+		}
+		break;
+	case 6:		/* CN50XX */
+		family = "50";
+		break;
+	case 7:		/* CN52XX */
+		if (l2d_fus3)
+			family = "51";
+		else
+			family = "52";
+		break;
+	case 0x93:		/* CN61XX */
+		family = "61";
+		if (fus_dat2.cn61xx.nocrypto && fus_dat2.cn61xx.dorm_crypto)
+			suffix = "AP";
+		if (fus_dat2.cn61xx.nocrypto)
+			suffix = "CP";
+		else if (fus_dat2.cn61xx.dorm_crypto)
+			suffix = "DAP";
+		else if (fus_dat3.cn61xx.nozip)
+			suffix = "SCP";
+		break;
+	case 0x90:		/* CN63XX */
+		family = "63";
+		if (fus_dat3.s.l2c_crip == 2)
+			family = "62";
+		if (num_cores == 6)	/* Other core counts match generic */
+			core_model = "35";
+		if (fus_dat2.cn63xx.nocrypto)
+			suffix = "CP";
+		else if (fus_dat2.cn63xx.dorm_crypto)
+			suffix = "DAP";
+		else if (fus_dat3.cn61xx.nozip)
+			suffix = "SCP";
+		else
+			suffix = "AAP";
+		break;
+	case 0x92:		/* CN66XX */
+		family = "66";
+		if (num_cores == 6)	/* Other core counts match generic */
+			core_model = "35";
+		if (fus_dat2.cn66xx.nocrypto && fus_dat2.cn66xx.dorm_crypto)
+			suffix = "AP";
+		if (fus_dat2.cn66xx.nocrypto)
+			suffix = "CP";
+		else if (fus_dat2.cn66xx.dorm_crypto)
+			suffix = "DAP";
+		else if (fus_dat3.cn61xx.nozip)
+			suffix = "SCP";
+		else
+			suffix = "AAP";
+		break;
+	case 0x91:		/* CN68XX */
+		family = "68";
+		if (fus_dat2.cn68xx.nocrypto && fus_dat3.cn61xx.nozip)
+			suffix = "CP";
+		else if (fus_dat2.cn68xx.dorm_crypto)
+			suffix = "DAP";
+		else if (fus_dat3.cn61xx.nozip)
+			suffix = "SCP";
+		else if (fus_dat2.cn68xx.nocrypto)
+			suffix = "SP";
+		else
+			suffix = "AAP";
+		break;
+	case 0x94:		/* CNF71XX */
+		family = "F71";
+		if (fus_dat3.cn61xx.nozip)
+			suffix = "SCP";
+		else
+			suffix = "AAP";
+		break;
+	case 0x95:		/* CN78XX */
+		if (num_cores == 6)	/* Other core counts match generic */
+			core_model = "35";
+		if (OCTEON_IS_MODEL(OCTEON_CN76XX))
+			family = "76";
+		else
+			family = "78";
+		if (fus_dat3.cn78xx.l2c_crip == 2)
+			family = "77";
+		if (fus_dat3.cn78xx.nozip
+		    && fus_dat3.cn78xx.nodfa_dte
+		    && fus_dat3.cn78xx.nohna_dte) {
+			if (fus_dat3.cn78xx.nozip &&
+				!fus_dat2.cn78xx.raid_en &&
+				fus_dat3.cn78xx.nohna_dte) {
+				suffix = "CP";
+			} else {
+				suffix = "SCP";
+			}
+		} else if (fus_dat2.cn78xx.raid_en == 0)
+			suffix = "HCP";
+		else
+			suffix = "AAP";
+		break;
+	case 0x96:		/* CN70XX */
+		family = "70";
+		if (cvmx_read_csr(CVMX_MIO_FUS_PDF) & (0x1ULL << 32))
+			family = "71";
+		if (fus_dat2.cn70xx.nocrypto)
+			suffix = "CP";
+		else if (fus_dat3.cn70xx.nodfa_dte)
+			suffix = "SCP";
+		else
+			suffix = "AAP";
+		break;
+	case 0x97:		/* CN73XX */
+		if (num_cores == 6)	/* Other core counts match generic */
+			core_model = "35";
+		family = "73";
+		if (fus_dat3.cn73xx.l2c_crip == 2)
+			family = "72";
+		if (fus_dat3.cn73xx.nozip
+				&& fus_dat3.cn73xx.nodfa_dte
+				&& fus_dat3.cn73xx.nohna_dte) {
+			if (!fus_dat2.cn73xx.raid_en)
+				suffix = "CP";
+			else
+				suffix = "SCP";
+		} else
+			suffix = "AAP";
+		break;
+	case 0x98:		/* CN75XX */
+		family = "F75";
+		if (fus_dat3.cn78xx.nozip
+		    && fus_dat3.cn78xx.nodfa_dte
+		    && fus_dat3.cn78xx.nohna_dte)
+			suffix = "SCP";
+		else
+			suffix = "AAP";
+		break;
+	default:
+		family = "XX";
+		core_model = "XX";
+		strcpy(pass, "X.X");
+		suffix = "XXX";
+		break;
+	}
+
+	clock_mhz = octeon_get_clock_rate() / 1000000;
+	if (family[0] != '3') {
+		int fuse_base = 384 / 8;
+		if (family[0] == '6')
+			fuse_base = 832 / 8;
+
+		/* Check for model in fuses, overrides normal decode */
+		/* This is _not_ valid for Octeon CN3XXX models */
+		fuse_data |= cvmx_fuse_read_byte(fuse_base + 3);
+		fuse_data = fuse_data << 8;
+		fuse_data |= cvmx_fuse_read_byte(fuse_base + 2);
+		fuse_data = fuse_data << 8;
+		fuse_data |= cvmx_fuse_read_byte(fuse_base + 1);
+		fuse_data = fuse_data << 8;
+		fuse_data |= cvmx_fuse_read_byte(fuse_base);
+		if (fuse_data & 0x7ffff) {
+			int model = fuse_data & 0x3fff;
+			int suffix = (fuse_data >> 14) & 0x1f;
+			if (suffix && model) {
+				/* Have both number and suffix in fuses, so both */
+				sprintf(fuse_model, "%d%c", model, 'A' + suffix - 1);
+				core_model = "";
+				family = fuse_model;
+			} else if (suffix && !model) {
+				/* Only have suffix, so add suffix to 'normal' model number */
+				sprintf(fuse_model, "%s%c", core_model, 'A' + suffix - 1);
+				core_model = fuse_model;
+			} else {
+				/* Don't have suffix, so just use model from fuses */
+				sprintf(fuse_model, "%d", model);
+				core_model = "";
+				family = fuse_model;
+			}
+		}
+	}
+	sprintf(buffer, "CN%s%sp%s-%d-%s", family, core_model, pass, clock_mhz, suffix);
+	return buffer;
+}
+
+/**
+ * Given the chip processor ID from COP0, this function returns a
+ * string representing the chip model number. The string is of the
+ * form CNXXXXpX.X-FREQ-SUFFIX.
+ * - XXXX = The chip model number
+ * - X.X = Chip pass number
+ * - FREQ = Current frequency in Mhz
+ * - SUFFIX = NSP, EXP, SCP, SSP, or CP
+ *
+ * @chip_id: Chip ID
+ *
+ * Returns Model string
+ */
+const char *__init octeon_model_get_string(uint32_t chip_id)
+{
+	static char buffer[32];
+	return octeon_model_get_string_buffer(chip_id, buffer);
+}
diff --git a/arch/mips/cavium-octeon/flash_setup.c b/arch/mips/cavium-octeon/flash_setup.c
new file mode 100644
index 000000000..c8a8c6d35
--- /dev/null
+++ b/arch/mips/cavium-octeon/flash_setup.c
@@ -0,0 +1,143 @@
+/*
+ *   Octeon Bootbus flash setup
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2007, 2008 Cavium Networks
+ */
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/semaphore.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/of_platform.h>
+#include <linux/mtd/partitions.h>
+
+#include <asm/octeon/octeon.h>
+
+static struct map_info flash_map;
+static struct mtd_info *mymtd;
+static const char *part_probe_types[] = {
+	"cmdlinepart",
+#ifdef CONFIG_MTD_REDBOOT_PARTS
+	"RedBoot",
+#endif
+	NULL
+};
+
+static map_word octeon_flash_map_read(struct map_info *map, unsigned long ofs)
+{
+	map_word r;
+
+	down(&octeon_bootbus_sem);
+	r = inline_map_read(map, ofs);
+	up(&octeon_bootbus_sem);
+
+	return r;
+}
+
+static void octeon_flash_map_write(struct map_info *map, const map_word datum,
+				   unsigned long ofs)
+{
+	down(&octeon_bootbus_sem);
+	inline_map_write(map, datum, ofs);
+	up(&octeon_bootbus_sem);
+}
+
+static void octeon_flash_map_copy_from(struct map_info *map, void *to,
+				       unsigned long from, ssize_t len)
+{
+	down(&octeon_bootbus_sem);
+	inline_map_copy_from(map, to, from, len);
+	up(&octeon_bootbus_sem);
+}
+
+static void octeon_flash_map_copy_to(struct map_info *map, unsigned long to,
+				     const void *from, ssize_t len)
+{
+	down(&octeon_bootbus_sem);
+	inline_map_copy_to(map, to, from, len);
+	up(&octeon_bootbus_sem);
+}
+
+/*
+ * Module/ driver initialization.
+ *
+ * Returns Zero on success
+ */
+static int octeon_flash_probe(struct platform_device *pdev)
+{
+	union cvmx_mio_boot_reg_cfgx region_cfg;
+	u32 cs;
+	int r;
+	struct device_node *np = pdev->dev.of_node;
+
+	r = of_property_read_u32(np, "reg", &cs);
+	if (r)
+		return r;
+
+	/*
+	 * Read the bootbus region 0 setup to determine the base
+	 * address of the flash.
+	 */
+	region_cfg.u64 = cvmx_read_csr(CVMX_MIO_BOOT_REG_CFGX(cs));
+	if (region_cfg.s.en) {
+		/*
+		 * The bootloader always takes the flash and sets its
+		 * address so the entire flash fits below
+		 * 0x1fc00000. This way the flash aliases to
+		 * 0x1fc00000 for booting. Software can access the
+		 * full flash at the true address, while core boot can
+		 * access 4MB.
+		 */
+		/* Use this name so old part lines work */
+		flash_map.name = "phys_mapped_flash";
+		flash_map.phys = region_cfg.s.base << 16;
+		flash_map.size = 0x1fc00000 - flash_map.phys;
+		/* 8-bit bus (0 + 1) or 16-bit bus (1 + 1) */
+		flash_map.bankwidth = region_cfg.s.width + 1;
+		flash_map.virt = ioremap(flash_map.phys, flash_map.size);
+		pr_notice("Bootbus flash: Setting flash for %luMB flash at "
+			  "0x%08llx\n", flash_map.size >> 20, flash_map.phys);
+		WARN_ON(!map_bankwidth_supported(flash_map.bankwidth));
+		flash_map.read = octeon_flash_map_read;
+		flash_map.write = octeon_flash_map_write;
+		flash_map.copy_from = octeon_flash_map_copy_from;
+		flash_map.copy_to = octeon_flash_map_copy_to;
+		mymtd = do_map_probe("cfi_probe", &flash_map);
+		if (mymtd) {
+			mymtd->owner = THIS_MODULE;
+			mtd_device_parse_register(mymtd, part_probe_types,
+						  NULL, NULL, 0);
+		} else {
+			pr_err("Failed to register MTD device for flash\n");
+		}
+	}
+	return 0;
+}
+
+static const struct of_device_id of_flash_match[] = {
+	{
+		.compatible	= "cfi-flash",
+	},
+	{ },
+};
+MODULE_DEVICE_TABLE(of, of_flash_match);
+
+static struct platform_driver of_flash_driver = {
+	.driver = {
+		.name = "octeon-of-flash",
+		.of_match_table = of_flash_match,
+	},
+	.probe		= octeon_flash_probe,
+};
+
+static int octeon_flash_init(void)
+{
+	return platform_driver_register(&of_flash_driver);
+}
+late_initcall(octeon_flash_init);
+
+MODULE_LICENSE("GPL");
diff --git a/arch/mips/cavium-octeon/oct_ilm.c b/arch/mips/cavium-octeon/oct_ilm.c
new file mode 100644
index 000000000..dc05262e8
--- /dev/null
+++ b/arch/mips/cavium-octeon/oct_ilm.c
@@ -0,0 +1,171 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include <linux/fs.h>
+#include <linux/interrupt.h>
+#include <asm/octeon/octeon.h>
+#include <asm/octeon/cvmx-ciu-defs.h>
+#include <asm/octeon/cvmx.h>
+#include <linux/debugfs.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/seq_file.h>
+
+#define TIMER_NUM 3
+
+static bool reset_stats;
+
+struct latency_info {
+	u64 io_interval;
+	u64 cpu_interval;
+	u64 timer_start1;
+	u64 timer_start2;
+	u64 max_latency;
+	u64 min_latency;
+	u64 latency_sum;
+	u64 average_latency;
+	u64 interrupt_cnt;
+};
+
+static struct latency_info li;
+static struct dentry *dir;
+
+static int oct_ilm_show(struct seq_file *m, void *v)
+{
+	u64 cpuclk, avg, max, min;
+	struct latency_info curr_li = li;
+
+	cpuclk = octeon_get_clock_rate();
+
+	max = (curr_li.max_latency * 1000000000) / cpuclk;
+	min = (curr_li.min_latency * 1000000000) / cpuclk;
+	avg = (curr_li.latency_sum * 1000000000) / (cpuclk * curr_li.interrupt_cnt);
+
+	seq_printf(m, "cnt: %10lld, avg: %7lld ns, max: %7lld ns, min: %7lld ns\n",
+		   curr_li.interrupt_cnt, avg, max, min);
+	return 0;
+}
+DEFINE_SHOW_ATTRIBUTE(oct_ilm);
+
+static int reset_statistics(void *data, u64 value)
+{
+	reset_stats = true;
+	return 0;
+}
+
+DEFINE_DEBUGFS_ATTRIBUTE(reset_statistics_ops, NULL, reset_statistics, "%llu\n");
+
+static void init_debugfs(void)
+{
+	dir = debugfs_create_dir("oct_ilm", 0);
+	debugfs_create_file("statistics", 0222, dir, NULL, &oct_ilm_fops);
+	debugfs_create_file("reset", 0222, dir, NULL, &reset_statistics_ops);
+}
+
+static void init_latency_info(struct latency_info *li, int startup)
+{
+	/* interval in milli seconds after which the interrupt will
+	 * be triggered
+	 */
+	int interval = 1;
+
+	if (startup) {
+		/* Calculating by the amounts io clock and cpu clock would
+		 *  increment in interval amount of ms
+		 */
+		li->io_interval = (octeon_get_io_clock_rate() * interval) / 1000;
+		li->cpu_interval = (octeon_get_clock_rate() * interval) / 1000;
+	}
+	li->timer_start1 = 0;
+	li->timer_start2 = 0;
+	li->max_latency = 0;
+	li->min_latency = (u64)-1;
+	li->latency_sum = 0;
+	li->interrupt_cnt = 0;
+}
+
+
+static void start_timer(int timer, u64 interval)
+{
+	union cvmx_ciu_timx timx;
+	unsigned long flags;
+
+	timx.u64 = 0;
+	timx.s.one_shot = 1;
+	timx.s.len = interval;
+	raw_local_irq_save(flags);
+	li.timer_start1 = read_c0_cvmcount();
+	cvmx_write_csr(CVMX_CIU_TIMX(timer), timx.u64);
+	/* Read it back to force wait until register is written. */
+	timx.u64 = cvmx_read_csr(CVMX_CIU_TIMX(timer));
+	li.timer_start2 = read_c0_cvmcount();
+	raw_local_irq_restore(flags);
+}
+
+
+static irqreturn_t cvm_oct_ciu_timer_interrupt(int cpl, void *dev_id)
+{
+	u64 last_latency;
+	u64 last_int_cnt;
+
+	if (reset_stats) {
+		init_latency_info(&li, 0);
+		reset_stats = false;
+	} else {
+		last_int_cnt = read_c0_cvmcount();
+		last_latency = last_int_cnt - (li.timer_start1 + li.cpu_interval);
+		li.interrupt_cnt++;
+		li.latency_sum += last_latency;
+		if (last_latency > li.max_latency)
+			li.max_latency = last_latency;
+		if (last_latency < li.min_latency)
+			li.min_latency = last_latency;
+	}
+	start_timer(TIMER_NUM, li.io_interval);
+	return IRQ_HANDLED;
+}
+
+static void disable_timer(int timer)
+{
+	union cvmx_ciu_timx timx;
+
+	timx.s.one_shot = 0;
+	timx.s.len = 0;
+	cvmx_write_csr(CVMX_CIU_TIMX(timer), timx.u64);
+	/* Read it back to force immediate write of timer register*/
+	timx.u64 = cvmx_read_csr(CVMX_CIU_TIMX(timer));
+}
+
+static __init int oct_ilm_module_init(void)
+{
+	int rc;
+	int irq = OCTEON_IRQ_TIMER0 + TIMER_NUM;
+
+	init_debugfs();
+
+	rc = request_irq(irq, cvm_oct_ciu_timer_interrupt, IRQF_NO_THREAD,
+			 "oct_ilm", 0);
+	if (rc) {
+		WARN(1, "Could not acquire IRQ %d", irq);
+		goto err_irq;
+	}
+
+	init_latency_info(&li, 1);
+	start_timer(TIMER_NUM, li.io_interval);
+
+	return 0;
+err_irq:
+	debugfs_remove_recursive(dir);
+	return rc;
+}
+
+static __exit void oct_ilm_module_exit(void)
+{
+	disable_timer(TIMER_NUM);
+	debugfs_remove_recursive(dir);
+	free_irq(OCTEON_IRQ_TIMER0 + TIMER_NUM, 0);
+}
+
+module_exit(oct_ilm_module_exit);
+module_init(oct_ilm_module_init);
+MODULE_AUTHOR("Venkat Subbiah, Cavium");
+MODULE_DESCRIPTION("Measures interrupt latency on Octeon chips.");
+MODULE_LICENSE("GPL");
diff --git a/arch/mips/cavium-octeon/octeon-irq.c b/arch/mips/cavium-octeon/octeon-irq.c
new file mode 100644
index 000000000..fd8043f6f
--- /dev/null
+++ b/arch/mips/cavium-octeon/octeon-irq.c
@@ -0,0 +1,3007 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2004-2016 Cavium, Inc.
+ */
+
+#include <linux/of_address.h>
+#include <linux/interrupt.h>
+#include <linux/irqdomain.h>
+#include <linux/bitops.h>
+#include <linux/of_irq.h>
+#include <linux/percpu.h>
+#include <linux/slab.h>
+#include <linux/irq.h>
+#include <linux/smp.h>
+#include <linux/of.h>
+
+#include <asm/octeon/octeon.h>
+#include <asm/octeon/cvmx-ciu2-defs.h>
+#include <asm/octeon/cvmx-ciu3-defs.h>
+
+static DEFINE_PER_CPU(unsigned long, octeon_irq_ciu0_en_mirror);
+static DEFINE_PER_CPU(unsigned long, octeon_irq_ciu1_en_mirror);
+static DEFINE_PER_CPU(raw_spinlock_t, octeon_irq_ciu_spinlock);
+static DEFINE_PER_CPU(unsigned int, octeon_irq_ciu3_idt_ip2);
+
+static DEFINE_PER_CPU(unsigned int, octeon_irq_ciu3_idt_ip3);
+static DEFINE_PER_CPU(struct octeon_ciu3_info *, octeon_ciu3_info);
+#define CIU3_MBOX_PER_CORE 10
+
+/*
+ * The 8 most significant bits of the intsn identify the interrupt major block.
+ * Each major block might use its own interrupt domain. Thus 256 domains are
+ * needed.
+ */
+#define MAX_CIU3_DOMAINS		256
+
+typedef irq_hw_number_t (*octeon_ciu3_intsn2hw_t)(struct irq_domain *, unsigned int);
+
+/* Information for each ciu3 in the system */
+struct octeon_ciu3_info {
+	u64			ciu3_addr;
+	int			node;
+	struct irq_domain	*domain[MAX_CIU3_DOMAINS];
+	octeon_ciu3_intsn2hw_t	intsn2hw[MAX_CIU3_DOMAINS];
+};
+
+/* Each ciu3 in the system uses its own data (one ciu3 per node) */
+static struct octeon_ciu3_info	*octeon_ciu3_info_per_node[4];
+
+struct octeon_irq_ciu_domain_data {
+	int num_sum;  /* number of sum registers (2 or 3). */
+};
+
+/* Register offsets from ciu3_addr */
+#define CIU3_CONST		0x220
+#define CIU3_IDT_CTL(_idt)	((_idt) * 8 + 0x110000)
+#define CIU3_IDT_PP(_idt, _idx)	((_idt) * 32 + (_idx) * 8 + 0x120000)
+#define CIU3_IDT_IO(_idt)	((_idt) * 8 + 0x130000)
+#define CIU3_DEST_PP_INT(_pp_ip) ((_pp_ip) * 8 + 0x200000)
+#define CIU3_DEST_IO_INT(_io)	((_io) * 8 + 0x210000)
+#define CIU3_ISC_CTL(_intsn)	((_intsn) * 8 + 0x80000000)
+#define CIU3_ISC_W1C(_intsn)	((_intsn) * 8 + 0x90000000)
+#define CIU3_ISC_W1S(_intsn)	((_intsn) * 8 + 0xa0000000)
+
+static __read_mostly int octeon_irq_ciu_to_irq[8][64];
+
+struct octeon_ciu_chip_data {
+	union {
+		struct {		/* only used for ciu3 */
+			u64 ciu3_addr;
+			unsigned int intsn;
+		};
+		struct {		/* only used for ciu/ciu2 */
+			u8 line;
+			u8 bit;
+		};
+	};
+	int gpio_line;
+	int current_cpu;	/* Next CPU expected to take this irq */
+	int ciu_node; /* NUMA node number of the CIU */
+};
+
+struct octeon_core_chip_data {
+	struct mutex core_irq_mutex;
+	bool current_en;
+	bool desired_en;
+	u8 bit;
+};
+
+#define MIPS_CORE_IRQ_LINES 8
+
+static struct octeon_core_chip_data octeon_irq_core_chip_data[MIPS_CORE_IRQ_LINES];
+
+static int octeon_irq_set_ciu_mapping(int irq, int line, int bit, int gpio_line,
+				      struct irq_chip *chip,
+				      irq_flow_handler_t handler)
+{
+	struct octeon_ciu_chip_data *cd;
+
+	cd = kzalloc(sizeof(*cd), GFP_KERNEL);
+	if (!cd)
+		return -ENOMEM;
+
+	irq_set_chip_and_handler(irq, chip, handler);
+
+	cd->line = line;
+	cd->bit = bit;
+	cd->gpio_line = gpio_line;
+
+	irq_set_chip_data(irq, cd);
+	octeon_irq_ciu_to_irq[line][bit] = irq;
+	return 0;
+}
+
+static void octeon_irq_free_cd(struct irq_domain *d, unsigned int irq)
+{
+	struct irq_data *data = irq_get_irq_data(irq);
+	struct octeon_ciu_chip_data *cd = irq_data_get_irq_chip_data(data);
+
+	irq_set_chip_data(irq, NULL);
+	kfree(cd);
+}
+
+static int octeon_irq_force_ciu_mapping(struct irq_domain *domain,
+					int irq, int line, int bit)
+{
+	struct device_node *of_node;
+	int ret;
+
+	of_node = irq_domain_get_of_node(domain);
+	if (!of_node)
+		return -EINVAL;
+	ret = irq_alloc_desc_at(irq, of_node_to_nid(of_node));
+	if (ret < 0)
+		return ret;
+
+	return irq_domain_associate(domain, irq, line << 6 | bit);
+}
+
+static int octeon_coreid_for_cpu(int cpu)
+{
+#ifdef CONFIG_SMP
+	return cpu_logical_map(cpu);
+#else
+	return cvmx_get_core_num();
+#endif
+}
+
+static int octeon_cpu_for_coreid(int coreid)
+{
+#ifdef CONFIG_SMP
+	return cpu_number_map(coreid);
+#else
+	return smp_processor_id();
+#endif
+}
+
+static void octeon_irq_core_ack(struct irq_data *data)
+{
+	struct octeon_core_chip_data *cd = irq_data_get_irq_chip_data(data);
+	unsigned int bit = cd->bit;
+
+	/*
+	 * We don't need to disable IRQs to make these atomic since
+	 * they are already disabled earlier in the low level
+	 * interrupt code.
+	 */
+	clear_c0_status(0x100 << bit);
+	/* The two user interrupts must be cleared manually. */
+	if (bit < 2)
+		clear_c0_cause(0x100 << bit);
+}
+
+static void octeon_irq_core_eoi(struct irq_data *data)
+{
+	struct octeon_core_chip_data *cd = irq_data_get_irq_chip_data(data);
+
+	/*
+	 * We don't need to disable IRQs to make these atomic since
+	 * they are already disabled earlier in the low level
+	 * interrupt code.
+	 */
+	set_c0_status(0x100 << cd->bit);
+}
+
+static void octeon_irq_core_set_enable_local(void *arg)
+{
+	struct irq_data *data = arg;
+	struct octeon_core_chip_data *cd = irq_data_get_irq_chip_data(data);
+	unsigned int mask = 0x100 << cd->bit;
+
+	/*
+	 * Interrupts are already disabled, so these are atomic.
+	 */
+	if (cd->desired_en)
+		set_c0_status(mask);
+	else
+		clear_c0_status(mask);
+
+}
+
+static void octeon_irq_core_disable(struct irq_data *data)
+{
+	struct octeon_core_chip_data *cd = irq_data_get_irq_chip_data(data);
+	cd->desired_en = false;
+}
+
+static void octeon_irq_core_enable(struct irq_data *data)
+{
+	struct octeon_core_chip_data *cd = irq_data_get_irq_chip_data(data);
+	cd->desired_en = true;
+}
+
+static void octeon_irq_core_bus_lock(struct irq_data *data)
+{
+	struct octeon_core_chip_data *cd = irq_data_get_irq_chip_data(data);
+
+	mutex_lock(&cd->core_irq_mutex);
+}
+
+static void octeon_irq_core_bus_sync_unlock(struct irq_data *data)
+{
+	struct octeon_core_chip_data *cd = irq_data_get_irq_chip_data(data);
+
+	if (cd->desired_en != cd->current_en) {
+		on_each_cpu(octeon_irq_core_set_enable_local, data, 1);
+
+		cd->current_en = cd->desired_en;
+	}
+
+	mutex_unlock(&cd->core_irq_mutex);
+}
+
+static struct irq_chip octeon_irq_chip_core = {
+	.name = "Core",
+	.irq_enable = octeon_irq_core_enable,
+	.irq_disable = octeon_irq_core_disable,
+	.irq_ack = octeon_irq_core_ack,
+	.irq_eoi = octeon_irq_core_eoi,
+	.irq_bus_lock = octeon_irq_core_bus_lock,
+	.irq_bus_sync_unlock = octeon_irq_core_bus_sync_unlock,
+
+	.irq_cpu_online = octeon_irq_core_eoi,
+	.irq_cpu_offline = octeon_irq_core_ack,
+	.flags = IRQCHIP_ONOFFLINE_ENABLED,
+};
+
+static void __init octeon_irq_init_core(void)
+{
+	int i;
+	int irq;
+	struct octeon_core_chip_data *cd;
+
+	for (i = 0; i < MIPS_CORE_IRQ_LINES; i++) {
+		cd = &octeon_irq_core_chip_data[i];
+		cd->current_en = false;
+		cd->desired_en = false;
+		cd->bit = i;
+		mutex_init(&cd->core_irq_mutex);
+
+		irq = OCTEON_IRQ_SW0 + i;
+		irq_set_chip_data(irq, cd);
+		irq_set_chip_and_handler(irq, &octeon_irq_chip_core,
+					 handle_percpu_irq);
+	}
+}
+
+static int next_cpu_for_irq(struct irq_data *data)
+{
+
+#ifdef CONFIG_SMP
+	int cpu;
+	const struct cpumask *mask = irq_data_get_affinity_mask(data);
+	int weight = cpumask_weight(mask);
+	struct octeon_ciu_chip_data *cd = irq_data_get_irq_chip_data(data);
+
+	if (weight > 1) {
+		cpu = cd->current_cpu;
+		for (;;) {
+			cpu = cpumask_next(cpu, mask);
+			if (cpu >= nr_cpu_ids) {
+				cpu = -1;
+				continue;
+			} else if (cpumask_test_cpu(cpu, cpu_online_mask)) {
+				break;
+			}
+		}
+	} else if (weight == 1) {
+		cpu = cpumask_first(mask);
+	} else {
+		cpu = smp_processor_id();
+	}
+	cd->current_cpu = cpu;
+	return cpu;
+#else
+	return smp_processor_id();
+#endif
+}
+
+static void octeon_irq_ciu_enable(struct irq_data *data)
+{
+	int cpu = next_cpu_for_irq(data);
+	int coreid = octeon_coreid_for_cpu(cpu);
+	unsigned long *pen;
+	unsigned long flags;
+	struct octeon_ciu_chip_data *cd;
+	raw_spinlock_t *lock = &per_cpu(octeon_irq_ciu_spinlock, cpu);
+
+	cd = irq_data_get_irq_chip_data(data);
+
+	raw_spin_lock_irqsave(lock, flags);
+	if (cd->line == 0) {
+		pen = &per_cpu(octeon_irq_ciu0_en_mirror, cpu);
+		__set_bit(cd->bit, pen);
+		/*
+		 * Must be visible to octeon_irq_ip{2,3}_ciu() before
+		 * enabling the irq.
+		 */
+		wmb();
+		cvmx_write_csr(CVMX_CIU_INTX_EN0(coreid * 2), *pen);
+	} else {
+		pen = &per_cpu(octeon_irq_ciu1_en_mirror, cpu);
+		__set_bit(cd->bit, pen);
+		/*
+		 * Must be visible to octeon_irq_ip{2,3}_ciu() before
+		 * enabling the irq.
+		 */
+		wmb();
+		cvmx_write_csr(CVMX_CIU_INTX_EN1(coreid * 2 + 1), *pen);
+	}
+	raw_spin_unlock_irqrestore(lock, flags);
+}
+
+static void octeon_irq_ciu_enable_local(struct irq_data *data)
+{
+	unsigned long *pen;
+	unsigned long flags;
+	struct octeon_ciu_chip_data *cd;
+	raw_spinlock_t *lock = this_cpu_ptr(&octeon_irq_ciu_spinlock);
+
+	cd = irq_data_get_irq_chip_data(data);
+
+	raw_spin_lock_irqsave(lock, flags);
+	if (cd->line == 0) {
+		pen = this_cpu_ptr(&octeon_irq_ciu0_en_mirror);
+		__set_bit(cd->bit, pen);
+		/*
+		 * Must be visible to octeon_irq_ip{2,3}_ciu() before
+		 * enabling the irq.
+		 */
+		wmb();
+		cvmx_write_csr(CVMX_CIU_INTX_EN0(cvmx_get_core_num() * 2), *pen);
+	} else {
+		pen = this_cpu_ptr(&octeon_irq_ciu1_en_mirror);
+		__set_bit(cd->bit, pen);
+		/*
+		 * Must be visible to octeon_irq_ip{2,3}_ciu() before
+		 * enabling the irq.
+		 */
+		wmb();
+		cvmx_write_csr(CVMX_CIU_INTX_EN1(cvmx_get_core_num() * 2 + 1), *pen);
+	}
+	raw_spin_unlock_irqrestore(lock, flags);
+}
+
+static void octeon_irq_ciu_disable_local(struct irq_data *data)
+{
+	unsigned long *pen;
+	unsigned long flags;
+	struct octeon_ciu_chip_data *cd;
+	raw_spinlock_t *lock = this_cpu_ptr(&octeon_irq_ciu_spinlock);
+
+	cd = irq_data_get_irq_chip_data(data);
+
+	raw_spin_lock_irqsave(lock, flags);
+	if (cd->line == 0) {
+		pen = this_cpu_ptr(&octeon_irq_ciu0_en_mirror);
+		__clear_bit(cd->bit, pen);
+		/*
+		 * Must be visible to octeon_irq_ip{2,3}_ciu() before
+		 * enabling the irq.
+		 */
+		wmb();
+		cvmx_write_csr(CVMX_CIU_INTX_EN0(cvmx_get_core_num() * 2), *pen);
+	} else {
+		pen = this_cpu_ptr(&octeon_irq_ciu1_en_mirror);
+		__clear_bit(cd->bit, pen);
+		/*
+		 * Must be visible to octeon_irq_ip{2,3}_ciu() before
+		 * enabling the irq.
+		 */
+		wmb();
+		cvmx_write_csr(CVMX_CIU_INTX_EN1(cvmx_get_core_num() * 2 + 1), *pen);
+	}
+	raw_spin_unlock_irqrestore(lock, flags);
+}
+
+static void octeon_irq_ciu_disable_all(struct irq_data *data)
+{
+	unsigned long flags;
+	unsigned long *pen;
+	int cpu;
+	struct octeon_ciu_chip_data *cd;
+	raw_spinlock_t *lock;
+
+	cd = irq_data_get_irq_chip_data(data);
+
+	for_each_online_cpu(cpu) {
+		int coreid = octeon_coreid_for_cpu(cpu);
+		lock = &per_cpu(octeon_irq_ciu_spinlock, cpu);
+		if (cd->line == 0)
+			pen = &per_cpu(octeon_irq_ciu0_en_mirror, cpu);
+		else
+			pen = &per_cpu(octeon_irq_ciu1_en_mirror, cpu);
+
+		raw_spin_lock_irqsave(lock, flags);
+		__clear_bit(cd->bit, pen);
+		/*
+		 * Must be visible to octeon_irq_ip{2,3}_ciu() before
+		 * enabling the irq.
+		 */
+		wmb();
+		if (cd->line == 0)
+			cvmx_write_csr(CVMX_CIU_INTX_EN0(coreid * 2), *pen);
+		else
+			cvmx_write_csr(CVMX_CIU_INTX_EN1(coreid * 2 + 1), *pen);
+		raw_spin_unlock_irqrestore(lock, flags);
+	}
+}
+
+static void octeon_irq_ciu_enable_all(struct irq_data *data)
+{
+	unsigned long flags;
+	unsigned long *pen;
+	int cpu;
+	struct octeon_ciu_chip_data *cd;
+	raw_spinlock_t *lock;
+
+	cd = irq_data_get_irq_chip_data(data);
+
+	for_each_online_cpu(cpu) {
+		int coreid = octeon_coreid_for_cpu(cpu);
+		lock = &per_cpu(octeon_irq_ciu_spinlock, cpu);
+		if (cd->line == 0)
+			pen = &per_cpu(octeon_irq_ciu0_en_mirror, cpu);
+		else
+			pen = &per_cpu(octeon_irq_ciu1_en_mirror, cpu);
+
+		raw_spin_lock_irqsave(lock, flags);
+		__set_bit(cd->bit, pen);
+		/*
+		 * Must be visible to octeon_irq_ip{2,3}_ciu() before
+		 * enabling the irq.
+		 */
+		wmb();
+		if (cd->line == 0)
+			cvmx_write_csr(CVMX_CIU_INTX_EN0(coreid * 2), *pen);
+		else
+			cvmx_write_csr(CVMX_CIU_INTX_EN1(coreid * 2 + 1), *pen);
+		raw_spin_unlock_irqrestore(lock, flags);
+	}
+}
+
+/*
+ * Enable the irq on the next core in the affinity set for chips that
+ * have the EN*_W1{S,C} registers.
+ */
+static void octeon_irq_ciu_enable_v2(struct irq_data *data)
+{
+	u64 mask;
+	int cpu = next_cpu_for_irq(data);
+	struct octeon_ciu_chip_data *cd;
+
+	cd = irq_data_get_irq_chip_data(data);
+	mask = 1ull << (cd->bit);
+
+	/*
+	 * Called under the desc lock, so these should never get out
+	 * of sync.
+	 */
+	if (cd->line == 0) {
+		int index = octeon_coreid_for_cpu(cpu) * 2;
+		set_bit(cd->bit, &per_cpu(octeon_irq_ciu0_en_mirror, cpu));
+		cvmx_write_csr(CVMX_CIU_INTX_EN0_W1S(index), mask);
+	} else {
+		int index = octeon_coreid_for_cpu(cpu) * 2 + 1;
+		set_bit(cd->bit, &per_cpu(octeon_irq_ciu1_en_mirror, cpu));
+		cvmx_write_csr(CVMX_CIU_INTX_EN1_W1S(index), mask);
+	}
+}
+
+/*
+ * Enable the irq in the sum2 registers.
+ */
+static void octeon_irq_ciu_enable_sum2(struct irq_data *data)
+{
+	u64 mask;
+	int cpu = next_cpu_for_irq(data);
+	int index = octeon_coreid_for_cpu(cpu);
+	struct octeon_ciu_chip_data *cd;
+
+	cd = irq_data_get_irq_chip_data(data);
+	mask = 1ull << (cd->bit);
+
+	cvmx_write_csr(CVMX_CIU_EN2_PPX_IP4_W1S(index), mask);
+}
+
+/*
+ * Disable the irq in the sum2 registers.
+ */
+static void octeon_irq_ciu_disable_local_sum2(struct irq_data *data)
+{
+	u64 mask;
+	int cpu = next_cpu_for_irq(data);
+	int index = octeon_coreid_for_cpu(cpu);
+	struct octeon_ciu_chip_data *cd;
+
+	cd = irq_data_get_irq_chip_data(data);
+	mask = 1ull << (cd->bit);
+
+	cvmx_write_csr(CVMX_CIU_EN2_PPX_IP4_W1C(index), mask);
+}
+
+static void octeon_irq_ciu_ack_sum2(struct irq_data *data)
+{
+	u64 mask;
+	int cpu = next_cpu_for_irq(data);
+	int index = octeon_coreid_for_cpu(cpu);
+	struct octeon_ciu_chip_data *cd;
+
+	cd = irq_data_get_irq_chip_data(data);
+	mask = 1ull << (cd->bit);
+
+	cvmx_write_csr(CVMX_CIU_SUM2_PPX_IP4(index), mask);
+}
+
+static void octeon_irq_ciu_disable_all_sum2(struct irq_data *data)
+{
+	int cpu;
+	struct octeon_ciu_chip_data *cd;
+	u64 mask;
+
+	cd = irq_data_get_irq_chip_data(data);
+	mask = 1ull << (cd->bit);
+
+	for_each_online_cpu(cpu) {
+		int coreid = octeon_coreid_for_cpu(cpu);
+
+		cvmx_write_csr(CVMX_CIU_EN2_PPX_IP4_W1C(coreid), mask);
+	}
+}
+
+/*
+ * Enable the irq on the current CPU for chips that
+ * have the EN*_W1{S,C} registers.
+ */
+static void octeon_irq_ciu_enable_local_v2(struct irq_data *data)
+{
+	u64 mask;
+	struct octeon_ciu_chip_data *cd;
+
+	cd = irq_data_get_irq_chip_data(data);
+	mask = 1ull << (cd->bit);
+
+	if (cd->line == 0) {
+		int index = cvmx_get_core_num() * 2;
+		set_bit(cd->bit, this_cpu_ptr(&octeon_irq_ciu0_en_mirror));
+		cvmx_write_csr(CVMX_CIU_INTX_EN0_W1S(index), mask);
+	} else {
+		int index = cvmx_get_core_num() * 2 + 1;
+		set_bit(cd->bit, this_cpu_ptr(&octeon_irq_ciu1_en_mirror));
+		cvmx_write_csr(CVMX_CIU_INTX_EN1_W1S(index), mask);
+	}
+}
+
+static void octeon_irq_ciu_disable_local_v2(struct irq_data *data)
+{
+	u64 mask;
+	struct octeon_ciu_chip_data *cd;
+
+	cd = irq_data_get_irq_chip_data(data);
+	mask = 1ull << (cd->bit);
+
+	if (cd->line == 0) {
+		int index = cvmx_get_core_num() * 2;
+		clear_bit(cd->bit, this_cpu_ptr(&octeon_irq_ciu0_en_mirror));
+		cvmx_write_csr(CVMX_CIU_INTX_EN0_W1C(index), mask);
+	} else {
+		int index = cvmx_get_core_num() * 2 + 1;
+		clear_bit(cd->bit, this_cpu_ptr(&octeon_irq_ciu1_en_mirror));
+		cvmx_write_csr(CVMX_CIU_INTX_EN1_W1C(index), mask);
+	}
+}
+
+/*
+ * Write to the W1C bit in CVMX_CIU_INTX_SUM0 to clear the irq.
+ */
+static void octeon_irq_ciu_ack(struct irq_data *data)
+{
+	u64 mask;
+	struct octeon_ciu_chip_data *cd;
+
+	cd = irq_data_get_irq_chip_data(data);
+	mask = 1ull << (cd->bit);
+
+	if (cd->line == 0) {
+		int index = cvmx_get_core_num() * 2;
+		cvmx_write_csr(CVMX_CIU_INTX_SUM0(index), mask);
+	} else {
+		cvmx_write_csr(CVMX_CIU_INT_SUM1, mask);
+	}
+}
+
+/*
+ * Disable the irq on the all cores for chips that have the EN*_W1{S,C}
+ * registers.
+ */
+static void octeon_irq_ciu_disable_all_v2(struct irq_data *data)
+{
+	int cpu;
+	u64 mask;
+	struct octeon_ciu_chip_data *cd;
+
+	cd = irq_data_get_irq_chip_data(data);
+	mask = 1ull << (cd->bit);
+
+	if (cd->line == 0) {
+		for_each_online_cpu(cpu) {
+			int index = octeon_coreid_for_cpu(cpu) * 2;
+			clear_bit(cd->bit,
+				&per_cpu(octeon_irq_ciu0_en_mirror, cpu));
+			cvmx_write_csr(CVMX_CIU_INTX_EN0_W1C(index), mask);
+		}
+	} else {
+		for_each_online_cpu(cpu) {
+			int index = octeon_coreid_for_cpu(cpu) * 2 + 1;
+			clear_bit(cd->bit,
+				&per_cpu(octeon_irq_ciu1_en_mirror, cpu));
+			cvmx_write_csr(CVMX_CIU_INTX_EN1_W1C(index), mask);
+		}
+	}
+}
+
+/*
+ * Enable the irq on the all cores for chips that have the EN*_W1{S,C}
+ * registers.
+ */
+static void octeon_irq_ciu_enable_all_v2(struct irq_data *data)
+{
+	int cpu;
+	u64 mask;
+	struct octeon_ciu_chip_data *cd;
+
+	cd = irq_data_get_irq_chip_data(data);
+	mask = 1ull << (cd->bit);
+
+	if (cd->line == 0) {
+		for_each_online_cpu(cpu) {
+			int index = octeon_coreid_for_cpu(cpu) * 2;
+			set_bit(cd->bit,
+				&per_cpu(octeon_irq_ciu0_en_mirror, cpu));
+			cvmx_write_csr(CVMX_CIU_INTX_EN0_W1S(index), mask);
+		}
+	} else {
+		for_each_online_cpu(cpu) {
+			int index = octeon_coreid_for_cpu(cpu) * 2 + 1;
+			set_bit(cd->bit,
+				&per_cpu(octeon_irq_ciu1_en_mirror, cpu));
+			cvmx_write_csr(CVMX_CIU_INTX_EN1_W1S(index), mask);
+		}
+	}
+}
+
+static int octeon_irq_ciu_set_type(struct irq_data *data, unsigned int t)
+{
+	irqd_set_trigger_type(data, t);
+
+	if (t & IRQ_TYPE_EDGE_BOTH)
+		irq_set_handler_locked(data, handle_edge_irq);
+	else
+		irq_set_handler_locked(data, handle_level_irq);
+
+	return IRQ_SET_MASK_OK;
+}
+
+static void octeon_irq_gpio_setup(struct irq_data *data)
+{
+	union cvmx_gpio_bit_cfgx cfg;
+	struct octeon_ciu_chip_data *cd;
+	u32 t = irqd_get_trigger_type(data);
+
+	cd = irq_data_get_irq_chip_data(data);
+
+	cfg.u64 = 0;
+	cfg.s.int_en = 1;
+	cfg.s.int_type = (t & IRQ_TYPE_EDGE_BOTH) != 0;
+	cfg.s.rx_xor = (t & (IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_EDGE_FALLING)) != 0;
+
+	/* 140 nS glitch filter*/
+	cfg.s.fil_cnt = 7;
+	cfg.s.fil_sel = 3;
+
+	cvmx_write_csr(CVMX_GPIO_BIT_CFGX(cd->gpio_line), cfg.u64);
+}
+
+static void octeon_irq_ciu_enable_gpio_v2(struct irq_data *data)
+{
+	octeon_irq_gpio_setup(data);
+	octeon_irq_ciu_enable_v2(data);
+}
+
+static void octeon_irq_ciu_enable_gpio(struct irq_data *data)
+{
+	octeon_irq_gpio_setup(data);
+	octeon_irq_ciu_enable(data);
+}
+
+static int octeon_irq_ciu_gpio_set_type(struct irq_data *data, unsigned int t)
+{
+	irqd_set_trigger_type(data, t);
+	octeon_irq_gpio_setup(data);
+
+	if (t & IRQ_TYPE_EDGE_BOTH)
+		irq_set_handler_locked(data, handle_edge_irq);
+	else
+		irq_set_handler_locked(data, handle_level_irq);
+
+	return IRQ_SET_MASK_OK;
+}
+
+static void octeon_irq_ciu_disable_gpio_v2(struct irq_data *data)
+{
+	struct octeon_ciu_chip_data *cd;
+
+	cd = irq_data_get_irq_chip_data(data);
+	cvmx_write_csr(CVMX_GPIO_BIT_CFGX(cd->gpio_line), 0);
+
+	octeon_irq_ciu_disable_all_v2(data);
+}
+
+static void octeon_irq_ciu_disable_gpio(struct irq_data *data)
+{
+	struct octeon_ciu_chip_data *cd;
+
+	cd = irq_data_get_irq_chip_data(data);
+	cvmx_write_csr(CVMX_GPIO_BIT_CFGX(cd->gpio_line), 0);
+
+	octeon_irq_ciu_disable_all(data);
+}
+
+static void octeon_irq_ciu_gpio_ack(struct irq_data *data)
+{
+	struct octeon_ciu_chip_data *cd;
+	u64 mask;
+
+	cd = irq_data_get_irq_chip_data(data);
+	mask = 1ull << (cd->gpio_line);
+
+	cvmx_write_csr(CVMX_GPIO_INT_CLR, mask);
+}
+
+#ifdef CONFIG_SMP
+
+static void octeon_irq_cpu_offline_ciu(struct irq_data *data)
+{
+	int cpu = smp_processor_id();
+	cpumask_t new_affinity;
+	const struct cpumask *mask = irq_data_get_affinity_mask(data);
+
+	if (!cpumask_test_cpu(cpu, mask))
+		return;
+
+	if (cpumask_weight(mask) > 1) {
+		/*
+		 * It has multi CPU affinity, just remove this CPU
+		 * from the affinity set.
+		 */
+		cpumask_copy(&new_affinity, mask);
+		cpumask_clear_cpu(cpu, &new_affinity);
+	} else {
+		/* Otherwise, put it on lowest numbered online CPU. */
+		cpumask_clear(&new_affinity);
+		cpumask_set_cpu(cpumask_first(cpu_online_mask), &new_affinity);
+	}
+	irq_set_affinity_locked(data, &new_affinity, false);
+}
+
+static int octeon_irq_ciu_set_affinity(struct irq_data *data,
+				       const struct cpumask *dest, bool force)
+{
+	int cpu;
+	bool enable_one = !irqd_irq_disabled(data) && !irqd_irq_masked(data);
+	unsigned long flags;
+	struct octeon_ciu_chip_data *cd;
+	unsigned long *pen;
+	raw_spinlock_t *lock;
+
+	cd = irq_data_get_irq_chip_data(data);
+
+	/*
+	 * For non-v2 CIU, we will allow only single CPU affinity.
+	 * This removes the need to do locking in the .ack/.eoi
+	 * functions.
+	 */
+	if (cpumask_weight(dest) != 1)
+		return -EINVAL;
+
+	if (!enable_one)
+		return 0;
+
+
+	for_each_online_cpu(cpu) {
+		int coreid = octeon_coreid_for_cpu(cpu);
+
+		lock = &per_cpu(octeon_irq_ciu_spinlock, cpu);
+		raw_spin_lock_irqsave(lock, flags);
+
+		if (cd->line == 0)
+			pen = &per_cpu(octeon_irq_ciu0_en_mirror, cpu);
+		else
+			pen = &per_cpu(octeon_irq_ciu1_en_mirror, cpu);
+
+		if (cpumask_test_cpu(cpu, dest) && enable_one) {
+			enable_one = false;
+			__set_bit(cd->bit, pen);
+		} else {
+			__clear_bit(cd->bit, pen);
+		}
+		/*
+		 * Must be visible to octeon_irq_ip{2,3}_ciu() before
+		 * enabling the irq.
+		 */
+		wmb();
+
+		if (cd->line == 0)
+			cvmx_write_csr(CVMX_CIU_INTX_EN0(coreid * 2), *pen);
+		else
+			cvmx_write_csr(CVMX_CIU_INTX_EN1(coreid * 2 + 1), *pen);
+
+		raw_spin_unlock_irqrestore(lock, flags);
+	}
+	return 0;
+}
+
+/*
+ * Set affinity for the irq for chips that have the EN*_W1{S,C}
+ * registers.
+ */
+static int octeon_irq_ciu_set_affinity_v2(struct irq_data *data,
+					  const struct cpumask *dest,
+					  bool force)
+{
+	int cpu;
+	bool enable_one = !irqd_irq_disabled(data) && !irqd_irq_masked(data);
+	u64 mask;
+	struct octeon_ciu_chip_data *cd;
+
+	if (!enable_one)
+		return 0;
+
+	cd = irq_data_get_irq_chip_data(data);
+	mask = 1ull << cd->bit;
+
+	if (cd->line == 0) {
+		for_each_online_cpu(cpu) {
+			unsigned long *pen = &per_cpu(octeon_irq_ciu0_en_mirror, cpu);
+			int index = octeon_coreid_for_cpu(cpu) * 2;
+			if (cpumask_test_cpu(cpu, dest) && enable_one) {
+				enable_one = false;
+				set_bit(cd->bit, pen);
+				cvmx_write_csr(CVMX_CIU_INTX_EN0_W1S(index), mask);
+			} else {
+				clear_bit(cd->bit, pen);
+				cvmx_write_csr(CVMX_CIU_INTX_EN0_W1C(index), mask);
+			}
+		}
+	} else {
+		for_each_online_cpu(cpu) {
+			unsigned long *pen = &per_cpu(octeon_irq_ciu1_en_mirror, cpu);
+			int index = octeon_coreid_for_cpu(cpu) * 2 + 1;
+			if (cpumask_test_cpu(cpu, dest) && enable_one) {
+				enable_one = false;
+				set_bit(cd->bit, pen);
+				cvmx_write_csr(CVMX_CIU_INTX_EN1_W1S(index), mask);
+			} else {
+				clear_bit(cd->bit, pen);
+				cvmx_write_csr(CVMX_CIU_INTX_EN1_W1C(index), mask);
+			}
+		}
+	}
+	return 0;
+}
+
+static int octeon_irq_ciu_set_affinity_sum2(struct irq_data *data,
+					    const struct cpumask *dest,
+					    bool force)
+{
+	int cpu;
+	bool enable_one = !irqd_irq_disabled(data) && !irqd_irq_masked(data);
+	u64 mask;
+	struct octeon_ciu_chip_data *cd;
+
+	if (!enable_one)
+		return 0;
+
+	cd = irq_data_get_irq_chip_data(data);
+	mask = 1ull << cd->bit;
+
+	for_each_online_cpu(cpu) {
+		int index = octeon_coreid_for_cpu(cpu);
+
+		if (cpumask_test_cpu(cpu, dest) && enable_one) {
+			enable_one = false;
+			cvmx_write_csr(CVMX_CIU_EN2_PPX_IP4_W1S(index), mask);
+		} else {
+			cvmx_write_csr(CVMX_CIU_EN2_PPX_IP4_W1C(index), mask);
+		}
+	}
+	return 0;
+}
+#endif
+
+static unsigned int edge_startup(struct irq_data *data)
+{
+	/* ack any pending edge-irq at startup, so there is
+	 * an _edge_ to fire on when the event reappears.
+	 */
+	data->chip->irq_ack(data);
+	data->chip->irq_enable(data);
+	return 0;
+}
+
+/*
+ * Newer octeon chips have support for lockless CIU operation.
+ */
+static struct irq_chip octeon_irq_chip_ciu_v2 = {
+	.name = "CIU",
+	.irq_enable = octeon_irq_ciu_enable_v2,
+	.irq_disable = octeon_irq_ciu_disable_all_v2,
+	.irq_mask = octeon_irq_ciu_disable_local_v2,
+	.irq_unmask = octeon_irq_ciu_enable_v2,
+#ifdef CONFIG_SMP
+	.irq_set_affinity = octeon_irq_ciu_set_affinity_v2,
+	.irq_cpu_offline = octeon_irq_cpu_offline_ciu,
+#endif
+};
+
+static struct irq_chip octeon_irq_chip_ciu_v2_edge = {
+	.name = "CIU",
+	.irq_enable = octeon_irq_ciu_enable_v2,
+	.irq_disable = octeon_irq_ciu_disable_all_v2,
+	.irq_ack = octeon_irq_ciu_ack,
+	.irq_mask = octeon_irq_ciu_disable_local_v2,
+	.irq_unmask = octeon_irq_ciu_enable_v2,
+#ifdef CONFIG_SMP
+	.irq_set_affinity = octeon_irq_ciu_set_affinity_v2,
+	.irq_cpu_offline = octeon_irq_cpu_offline_ciu,
+#endif
+};
+
+/*
+ * Newer octeon chips have support for lockless CIU operation.
+ */
+static struct irq_chip octeon_irq_chip_ciu_sum2 = {
+	.name = "CIU",
+	.irq_enable = octeon_irq_ciu_enable_sum2,
+	.irq_disable = octeon_irq_ciu_disable_all_sum2,
+	.irq_mask = octeon_irq_ciu_disable_local_sum2,
+	.irq_unmask = octeon_irq_ciu_enable_sum2,
+#ifdef CONFIG_SMP
+	.irq_set_affinity = octeon_irq_ciu_set_affinity_sum2,
+	.irq_cpu_offline = octeon_irq_cpu_offline_ciu,
+#endif
+};
+
+static struct irq_chip octeon_irq_chip_ciu_sum2_edge = {
+	.name = "CIU",
+	.irq_enable = octeon_irq_ciu_enable_sum2,
+	.irq_disable = octeon_irq_ciu_disable_all_sum2,
+	.irq_ack = octeon_irq_ciu_ack_sum2,
+	.irq_mask = octeon_irq_ciu_disable_local_sum2,
+	.irq_unmask = octeon_irq_ciu_enable_sum2,
+#ifdef CONFIG_SMP
+	.irq_set_affinity = octeon_irq_ciu_set_affinity_sum2,
+	.irq_cpu_offline = octeon_irq_cpu_offline_ciu,
+#endif
+};
+
+static struct irq_chip octeon_irq_chip_ciu = {
+	.name = "CIU",
+	.irq_enable = octeon_irq_ciu_enable,
+	.irq_disable = octeon_irq_ciu_disable_all,
+	.irq_mask = octeon_irq_ciu_disable_local,
+	.irq_unmask = octeon_irq_ciu_enable,
+#ifdef CONFIG_SMP
+	.irq_set_affinity = octeon_irq_ciu_set_affinity,
+	.irq_cpu_offline = octeon_irq_cpu_offline_ciu,
+#endif
+};
+
+static struct irq_chip octeon_irq_chip_ciu_edge = {
+	.name = "CIU",
+	.irq_enable = octeon_irq_ciu_enable,
+	.irq_disable = octeon_irq_ciu_disable_all,
+	.irq_ack = octeon_irq_ciu_ack,
+	.irq_mask = octeon_irq_ciu_disable_local,
+	.irq_unmask = octeon_irq_ciu_enable,
+#ifdef CONFIG_SMP
+	.irq_set_affinity = octeon_irq_ciu_set_affinity,
+	.irq_cpu_offline = octeon_irq_cpu_offline_ciu,
+#endif
+};
+
+/* The mbox versions don't do any affinity or round-robin. */
+static struct irq_chip octeon_irq_chip_ciu_mbox_v2 = {
+	.name = "CIU-M",
+	.irq_enable = octeon_irq_ciu_enable_all_v2,
+	.irq_disable = octeon_irq_ciu_disable_all_v2,
+	.irq_ack = octeon_irq_ciu_disable_local_v2,
+	.irq_eoi = octeon_irq_ciu_enable_local_v2,
+
+	.irq_cpu_online = octeon_irq_ciu_enable_local_v2,
+	.irq_cpu_offline = octeon_irq_ciu_disable_local_v2,
+	.flags = IRQCHIP_ONOFFLINE_ENABLED,
+};
+
+static struct irq_chip octeon_irq_chip_ciu_mbox = {
+	.name = "CIU-M",
+	.irq_enable = octeon_irq_ciu_enable_all,
+	.irq_disable = octeon_irq_ciu_disable_all,
+	.irq_ack = octeon_irq_ciu_disable_local,
+	.irq_eoi = octeon_irq_ciu_enable_local,
+
+	.irq_cpu_online = octeon_irq_ciu_enable_local,
+	.irq_cpu_offline = octeon_irq_ciu_disable_local,
+	.flags = IRQCHIP_ONOFFLINE_ENABLED,
+};
+
+static struct irq_chip octeon_irq_chip_ciu_gpio_v2 = {
+	.name = "CIU-GPIO",
+	.irq_enable = octeon_irq_ciu_enable_gpio_v2,
+	.irq_disable = octeon_irq_ciu_disable_gpio_v2,
+	.irq_ack = octeon_irq_ciu_gpio_ack,
+	.irq_mask = octeon_irq_ciu_disable_local_v2,
+	.irq_unmask = octeon_irq_ciu_enable_v2,
+	.irq_set_type = octeon_irq_ciu_gpio_set_type,
+#ifdef CONFIG_SMP
+	.irq_set_affinity = octeon_irq_ciu_set_affinity_v2,
+	.irq_cpu_offline = octeon_irq_cpu_offline_ciu,
+#endif
+	.flags = IRQCHIP_SET_TYPE_MASKED,
+};
+
+static struct irq_chip octeon_irq_chip_ciu_gpio = {
+	.name = "CIU-GPIO",
+	.irq_enable = octeon_irq_ciu_enable_gpio,
+	.irq_disable = octeon_irq_ciu_disable_gpio,
+	.irq_mask = octeon_irq_ciu_disable_local,
+	.irq_unmask = octeon_irq_ciu_enable,
+	.irq_ack = octeon_irq_ciu_gpio_ack,
+	.irq_set_type = octeon_irq_ciu_gpio_set_type,
+#ifdef CONFIG_SMP
+	.irq_set_affinity = octeon_irq_ciu_set_affinity,
+	.irq_cpu_offline = octeon_irq_cpu_offline_ciu,
+#endif
+	.flags = IRQCHIP_SET_TYPE_MASKED,
+};
+
+/*
+ * Watchdog interrupts are special.  They are associated with a single
+ * core, so we hardwire the affinity to that core.
+ */
+static void octeon_irq_ciu_wd_enable(struct irq_data *data)
+{
+	unsigned long flags;
+	unsigned long *pen;
+	int coreid = data->irq - OCTEON_IRQ_WDOG0;	/* Bit 0-63 of EN1 */
+	int cpu = octeon_cpu_for_coreid(coreid);
+	raw_spinlock_t *lock = &per_cpu(octeon_irq_ciu_spinlock, cpu);
+
+	raw_spin_lock_irqsave(lock, flags);
+	pen = &per_cpu(octeon_irq_ciu1_en_mirror, cpu);
+	__set_bit(coreid, pen);
+	/*
+	 * Must be visible to octeon_irq_ip{2,3}_ciu() before enabling
+	 * the irq.
+	 */
+	wmb();
+	cvmx_write_csr(CVMX_CIU_INTX_EN1(coreid * 2 + 1), *pen);
+	raw_spin_unlock_irqrestore(lock, flags);
+}
+
+/*
+ * Watchdog interrupts are special.  They are associated with a single
+ * core, so we hardwire the affinity to that core.
+ */
+static void octeon_irq_ciu1_wd_enable_v2(struct irq_data *data)
+{
+	int coreid = data->irq - OCTEON_IRQ_WDOG0;
+	int cpu = octeon_cpu_for_coreid(coreid);
+
+	set_bit(coreid, &per_cpu(octeon_irq_ciu1_en_mirror, cpu));
+	cvmx_write_csr(CVMX_CIU_INTX_EN1_W1S(coreid * 2 + 1), 1ull << coreid);
+}
+
+
+static struct irq_chip octeon_irq_chip_ciu_wd_v2 = {
+	.name = "CIU-W",
+	.irq_enable = octeon_irq_ciu1_wd_enable_v2,
+	.irq_disable = octeon_irq_ciu_disable_all_v2,
+	.irq_mask = octeon_irq_ciu_disable_local_v2,
+	.irq_unmask = octeon_irq_ciu_enable_local_v2,
+};
+
+static struct irq_chip octeon_irq_chip_ciu_wd = {
+	.name = "CIU-W",
+	.irq_enable = octeon_irq_ciu_wd_enable,
+	.irq_disable = octeon_irq_ciu_disable_all,
+	.irq_mask = octeon_irq_ciu_disable_local,
+	.irq_unmask = octeon_irq_ciu_enable_local,
+};
+
+static bool octeon_irq_ciu_is_edge(unsigned int line, unsigned int bit)
+{
+	bool edge = false;
+
+	if (line == 0)
+		switch (bit) {
+		case 48 ... 49: /* GMX DRP */
+		case 50: /* IPD_DRP */
+		case 52 ... 55: /* Timers */
+		case 58: /* MPI */
+			edge = true;
+			break;
+		default:
+			break;
+		}
+	else /* line == 1 */
+		switch (bit) {
+		case 47: /* PTP */
+			edge = true;
+			break;
+		default:
+			break;
+		}
+	return edge;
+}
+
+struct octeon_irq_gpio_domain_data {
+	unsigned int base_hwirq;
+};
+
+static int octeon_irq_gpio_xlat(struct irq_domain *d,
+				struct device_node *node,
+				const u32 *intspec,
+				unsigned int intsize,
+				unsigned long *out_hwirq,
+				unsigned int *out_type)
+{
+	unsigned int type;
+	unsigned int pin;
+	unsigned int trigger;
+
+	if (irq_domain_get_of_node(d) != node)
+		return -EINVAL;
+
+	if (intsize < 2)
+		return -EINVAL;
+
+	pin = intspec[0];
+	if (pin >= 16)
+		return -EINVAL;
+
+	trigger = intspec[1];
+
+	switch (trigger) {
+	case 1:
+		type = IRQ_TYPE_EDGE_RISING;
+		break;
+	case 2:
+		type = IRQ_TYPE_EDGE_FALLING;
+		break;
+	case 4:
+		type = IRQ_TYPE_LEVEL_HIGH;
+		break;
+	case 8:
+		type = IRQ_TYPE_LEVEL_LOW;
+		break;
+	default:
+		pr_err("Error: (%pOFn) Invalid irq trigger specification: %x\n",
+		       node,
+		       trigger);
+		type = IRQ_TYPE_LEVEL_LOW;
+		break;
+	}
+	*out_type = type;
+	*out_hwirq = pin;
+
+	return 0;
+}
+
+static int octeon_irq_ciu_xlat(struct irq_domain *d,
+			       struct device_node *node,
+			       const u32 *intspec,
+			       unsigned int intsize,
+			       unsigned long *out_hwirq,
+			       unsigned int *out_type)
+{
+	unsigned int ciu, bit;
+	struct octeon_irq_ciu_domain_data *dd = d->host_data;
+
+	ciu = intspec[0];
+	bit = intspec[1];
+
+	if (ciu >= dd->num_sum || bit > 63)
+		return -EINVAL;
+
+	*out_hwirq = (ciu << 6) | bit;
+	*out_type = 0;
+
+	return 0;
+}
+
+static struct irq_chip *octeon_irq_ciu_chip;
+static struct irq_chip *octeon_irq_ciu_chip_edge;
+static struct irq_chip *octeon_irq_gpio_chip;
+
+static int octeon_irq_ciu_map(struct irq_domain *d,
+			      unsigned int virq, irq_hw_number_t hw)
+{
+	int rv;
+	unsigned int line = hw >> 6;
+	unsigned int bit = hw & 63;
+	struct octeon_irq_ciu_domain_data *dd = d->host_data;
+
+	if (line >= dd->num_sum || octeon_irq_ciu_to_irq[line][bit] != 0)
+		return -EINVAL;
+
+	if (line == 2) {
+		if (octeon_irq_ciu_is_edge(line, bit))
+			rv = octeon_irq_set_ciu_mapping(virq, line, bit, 0,
+				&octeon_irq_chip_ciu_sum2_edge,
+				handle_edge_irq);
+		else
+			rv = octeon_irq_set_ciu_mapping(virq, line, bit, 0,
+				&octeon_irq_chip_ciu_sum2,
+				handle_level_irq);
+	} else {
+		if (octeon_irq_ciu_is_edge(line, bit))
+			rv = octeon_irq_set_ciu_mapping(virq, line, bit, 0,
+				octeon_irq_ciu_chip_edge,
+				handle_edge_irq);
+		else
+			rv = octeon_irq_set_ciu_mapping(virq, line, bit, 0,
+				octeon_irq_ciu_chip,
+				handle_level_irq);
+	}
+	return rv;
+}
+
+static int octeon_irq_gpio_map(struct irq_domain *d,
+			       unsigned int virq, irq_hw_number_t hw)
+{
+	struct octeon_irq_gpio_domain_data *gpiod = d->host_data;
+	unsigned int line, bit;
+	int r;
+
+	line = (hw + gpiod->base_hwirq) >> 6;
+	bit = (hw + gpiod->base_hwirq) & 63;
+	if (line >= ARRAY_SIZE(octeon_irq_ciu_to_irq) ||
+		octeon_irq_ciu_to_irq[line][bit] != 0)
+		return -EINVAL;
+
+	/*
+	 * Default to handle_level_irq. If the DT contains a different
+	 * trigger type, it will call the irq_set_type callback and
+	 * the handler gets updated.
+	 */
+	r = octeon_irq_set_ciu_mapping(virq, line, bit, hw,
+				       octeon_irq_gpio_chip, handle_level_irq);
+	return r;
+}
+
+static const struct irq_domain_ops octeon_irq_domain_ciu_ops = {
+	.map = octeon_irq_ciu_map,
+	.unmap = octeon_irq_free_cd,
+	.xlate = octeon_irq_ciu_xlat,
+};
+
+static const struct irq_domain_ops octeon_irq_domain_gpio_ops = {
+	.map = octeon_irq_gpio_map,
+	.unmap = octeon_irq_free_cd,
+	.xlate = octeon_irq_gpio_xlat,
+};
+
+static void octeon_irq_ip2_ciu(void)
+{
+	const unsigned long core_id = cvmx_get_core_num();
+	u64 ciu_sum = cvmx_read_csr(CVMX_CIU_INTX_SUM0(core_id * 2));
+
+	ciu_sum &= __this_cpu_read(octeon_irq_ciu0_en_mirror);
+	if (likely(ciu_sum)) {
+		int bit = fls64(ciu_sum) - 1;
+		int irq = octeon_irq_ciu_to_irq[0][bit];
+		if (likely(irq))
+			do_IRQ(irq);
+		else
+			spurious_interrupt();
+	} else {
+		spurious_interrupt();
+	}
+}
+
+static void octeon_irq_ip3_ciu(void)
+{
+	u64 ciu_sum = cvmx_read_csr(CVMX_CIU_INT_SUM1);
+
+	ciu_sum &= __this_cpu_read(octeon_irq_ciu1_en_mirror);
+	if (likely(ciu_sum)) {
+		int bit = fls64(ciu_sum) - 1;
+		int irq = octeon_irq_ciu_to_irq[1][bit];
+		if (likely(irq))
+			do_IRQ(irq);
+		else
+			spurious_interrupt();
+	} else {
+		spurious_interrupt();
+	}
+}
+
+static void octeon_irq_ip4_ciu(void)
+{
+	int coreid = cvmx_get_core_num();
+	u64 ciu_sum = cvmx_read_csr(CVMX_CIU_SUM2_PPX_IP4(coreid));
+	u64 ciu_en = cvmx_read_csr(CVMX_CIU_EN2_PPX_IP4(coreid));
+
+	ciu_sum &= ciu_en;
+	if (likely(ciu_sum)) {
+		int bit = fls64(ciu_sum) - 1;
+		int irq = octeon_irq_ciu_to_irq[2][bit];
+
+		if (likely(irq))
+			do_IRQ(irq);
+		else
+			spurious_interrupt();
+	} else {
+		spurious_interrupt();
+	}
+}
+
+static bool octeon_irq_use_ip4;
+
+static void octeon_irq_local_enable_ip4(void *arg)
+{
+	set_c0_status(STATUSF_IP4);
+}
+
+static void octeon_irq_ip4_mask(void)
+{
+	clear_c0_status(STATUSF_IP4);
+	spurious_interrupt();
+}
+
+static void (*octeon_irq_ip2)(void);
+static void (*octeon_irq_ip3)(void);
+static void (*octeon_irq_ip4)(void);
+
+void (*octeon_irq_setup_secondary)(void);
+
+void octeon_irq_set_ip4_handler(octeon_irq_ip4_handler_t h)
+{
+	octeon_irq_ip4 = h;
+	octeon_irq_use_ip4 = true;
+	on_each_cpu(octeon_irq_local_enable_ip4, NULL, 1);
+}
+
+static void octeon_irq_percpu_enable(void)
+{
+	irq_cpu_online();
+}
+
+static void octeon_irq_init_ciu_percpu(void)
+{
+	int coreid = cvmx_get_core_num();
+
+
+	__this_cpu_write(octeon_irq_ciu0_en_mirror, 0);
+	__this_cpu_write(octeon_irq_ciu1_en_mirror, 0);
+	wmb();
+	raw_spin_lock_init(this_cpu_ptr(&octeon_irq_ciu_spinlock));
+	/*
+	 * Disable All CIU Interrupts. The ones we need will be
+	 * enabled later.  Read the SUM register so we know the write
+	 * completed.
+	 */
+	cvmx_write_csr(CVMX_CIU_INTX_EN0((coreid * 2)), 0);
+	cvmx_write_csr(CVMX_CIU_INTX_EN0((coreid * 2 + 1)), 0);
+	cvmx_write_csr(CVMX_CIU_INTX_EN1((coreid * 2)), 0);
+	cvmx_write_csr(CVMX_CIU_INTX_EN1((coreid * 2 + 1)), 0);
+	cvmx_read_csr(CVMX_CIU_INTX_SUM0((coreid * 2)));
+}
+
+static void octeon_irq_init_ciu2_percpu(void)
+{
+	u64 regx, ipx;
+	int coreid = cvmx_get_core_num();
+	u64 base = CVMX_CIU2_EN_PPX_IP2_WRKQ(coreid);
+
+	/*
+	 * Disable All CIU2 Interrupts. The ones we need will be
+	 * enabled later.  Read the SUM register so we know the write
+	 * completed.
+	 *
+	 * There are 9 registers and 3 IPX levels with strides 0x1000
+	 * and 0x200 respectively.  Use loops to clear them.
+	 */
+	for (regx = 0; regx <= 0x8000; regx += 0x1000) {
+		for (ipx = 0; ipx <= 0x400; ipx += 0x200)
+			cvmx_write_csr(base + regx + ipx, 0);
+	}
+
+	cvmx_read_csr(CVMX_CIU2_SUM_PPX_IP2(coreid));
+}
+
+static void octeon_irq_setup_secondary_ciu(void)
+{
+	octeon_irq_init_ciu_percpu();
+	octeon_irq_percpu_enable();
+
+	/* Enable the CIU lines */
+	set_c0_status(STATUSF_IP3 | STATUSF_IP2);
+	if (octeon_irq_use_ip4)
+		set_c0_status(STATUSF_IP4);
+	else
+		clear_c0_status(STATUSF_IP4);
+}
+
+static void octeon_irq_setup_secondary_ciu2(void)
+{
+	octeon_irq_init_ciu2_percpu();
+	octeon_irq_percpu_enable();
+
+	/* Enable the CIU lines */
+	set_c0_status(STATUSF_IP3 | STATUSF_IP2);
+	if (octeon_irq_use_ip4)
+		set_c0_status(STATUSF_IP4);
+	else
+		clear_c0_status(STATUSF_IP4);
+}
+
+static int __init octeon_irq_init_ciu(
+	struct device_node *ciu_node, struct device_node *parent)
+{
+	int i, r;
+	struct irq_chip *chip;
+	struct irq_chip *chip_edge;
+	struct irq_chip *chip_mbox;
+	struct irq_chip *chip_wd;
+	struct irq_domain *ciu_domain = NULL;
+	struct octeon_irq_ciu_domain_data *dd;
+
+	dd = kzalloc(sizeof(*dd), GFP_KERNEL);
+	if (!dd)
+		return -ENOMEM;
+
+	octeon_irq_init_ciu_percpu();
+	octeon_irq_setup_secondary = octeon_irq_setup_secondary_ciu;
+
+	octeon_irq_ip2 = octeon_irq_ip2_ciu;
+	octeon_irq_ip3 = octeon_irq_ip3_ciu;
+	if ((OCTEON_IS_OCTEON2() || OCTEON_IS_OCTEON3())
+		&& !OCTEON_IS_MODEL(OCTEON_CN63XX)) {
+		octeon_irq_ip4 =  octeon_irq_ip4_ciu;
+		dd->num_sum = 3;
+		octeon_irq_use_ip4 = true;
+	} else {
+		octeon_irq_ip4 = octeon_irq_ip4_mask;
+		dd->num_sum = 2;
+		octeon_irq_use_ip4 = false;
+	}
+	if (OCTEON_IS_MODEL(OCTEON_CN58XX_PASS2_X) ||
+	    OCTEON_IS_MODEL(OCTEON_CN56XX_PASS2_X) ||
+	    OCTEON_IS_MODEL(OCTEON_CN52XX_PASS2_X) ||
+	    OCTEON_IS_OCTEON2() || OCTEON_IS_OCTEON3()) {
+		chip = &octeon_irq_chip_ciu_v2;
+		chip_edge = &octeon_irq_chip_ciu_v2_edge;
+		chip_mbox = &octeon_irq_chip_ciu_mbox_v2;
+		chip_wd = &octeon_irq_chip_ciu_wd_v2;
+		octeon_irq_gpio_chip = &octeon_irq_chip_ciu_gpio_v2;
+	} else {
+		chip = &octeon_irq_chip_ciu;
+		chip_edge = &octeon_irq_chip_ciu_edge;
+		chip_mbox = &octeon_irq_chip_ciu_mbox;
+		chip_wd = &octeon_irq_chip_ciu_wd;
+		octeon_irq_gpio_chip = &octeon_irq_chip_ciu_gpio;
+	}
+	octeon_irq_ciu_chip = chip;
+	octeon_irq_ciu_chip_edge = chip_edge;
+
+	/* Mips internal */
+	octeon_irq_init_core();
+
+	ciu_domain = irq_domain_add_tree(
+		ciu_node, &octeon_irq_domain_ciu_ops, dd);
+	irq_set_default_host(ciu_domain);
+
+	/* CIU_0 */
+	for (i = 0; i < 16; i++) {
+		r = octeon_irq_force_ciu_mapping(
+			ciu_domain, i + OCTEON_IRQ_WORKQ0, 0, i + 0);
+		if (r)
+			goto err;
+	}
+
+	r = irq_alloc_desc_at(OCTEON_IRQ_MBOX0, -1);
+	if (r < 0) {
+		pr_err("Failed to allocate desc for %s\n", "OCTEON_IRQ_MBOX0");
+		goto err;
+	}
+	r = octeon_irq_set_ciu_mapping(
+		OCTEON_IRQ_MBOX0, 0, 32, 0, chip_mbox, handle_percpu_irq);
+	if (r)
+		goto err;
+	r = irq_alloc_desc_at(OCTEON_IRQ_MBOX1, -1);
+	if (r < 0) {
+		pr_err("Failed to allocate desc for %s\n", "OCTEON_IRQ_MBOX1");
+		goto err;
+	}
+	r = octeon_irq_set_ciu_mapping(
+		OCTEON_IRQ_MBOX1, 0, 33, 0, chip_mbox, handle_percpu_irq);
+	if (r)
+		goto err;
+
+	for (i = 0; i < 4; i++) {
+		r = octeon_irq_force_ciu_mapping(
+			ciu_domain, i + OCTEON_IRQ_PCI_INT0, 0, i + 36);
+		if (r)
+			goto err;
+	}
+	for (i = 0; i < 4; i++) {
+		r = octeon_irq_force_ciu_mapping(
+			ciu_domain, i + OCTEON_IRQ_PCI_MSI0, 0, i + 40);
+		if (r)
+			goto err;
+	}
+
+	r = octeon_irq_force_ciu_mapping(ciu_domain, OCTEON_IRQ_TWSI, 0, 45);
+	if (r)
+		goto err;
+
+	r = octeon_irq_force_ciu_mapping(ciu_domain, OCTEON_IRQ_RML, 0, 46);
+	if (r)
+		goto err;
+
+	for (i = 0; i < 4; i++) {
+		r = octeon_irq_force_ciu_mapping(
+			ciu_domain, i + OCTEON_IRQ_TIMER0, 0, i + 52);
+		if (r)
+			goto err;
+	}
+
+	r = octeon_irq_force_ciu_mapping(ciu_domain, OCTEON_IRQ_TWSI2, 0, 59);
+	if (r)
+		goto err;
+
+	r = irq_alloc_descs(OCTEON_IRQ_WDOG0, OCTEON_IRQ_WDOG0, 16, -1);
+	if (r < 0) {
+		pr_err("Failed to allocate desc for %s\n", "OCTEON_IRQ_WDOGx");
+		goto err;
+	}
+	/* CIU_1 */
+	for (i = 0; i < 16; i++) {
+		r = octeon_irq_set_ciu_mapping(
+			i + OCTEON_IRQ_WDOG0, 1, i + 0, 0, chip_wd,
+			handle_level_irq);
+		if (r)
+			goto err;
+	}
+
+	/* Enable the CIU lines */
+	set_c0_status(STATUSF_IP3 | STATUSF_IP2);
+	if (octeon_irq_use_ip4)
+		set_c0_status(STATUSF_IP4);
+	else
+		clear_c0_status(STATUSF_IP4);
+
+	return 0;
+err:
+	return r;
+}
+
+static int __init octeon_irq_init_gpio(
+	struct device_node *gpio_node, struct device_node *parent)
+{
+	struct octeon_irq_gpio_domain_data *gpiod;
+	u32 interrupt_cells;
+	unsigned int base_hwirq;
+	int r;
+
+	r = of_property_read_u32(parent, "#interrupt-cells", &interrupt_cells);
+	if (r)
+		return r;
+
+	if (interrupt_cells == 1) {
+		u32 v;
+
+		r = of_property_read_u32_index(gpio_node, "interrupts", 0, &v);
+		if (r) {
+			pr_warn("No \"interrupts\" property.\n");
+			return r;
+		}
+		base_hwirq = v;
+	} else if (interrupt_cells == 2) {
+		u32 v0, v1;
+
+		r = of_property_read_u32_index(gpio_node, "interrupts", 0, &v0);
+		if (r) {
+			pr_warn("No \"interrupts\" property.\n");
+			return r;
+		}
+		r = of_property_read_u32_index(gpio_node, "interrupts", 1, &v1);
+		if (r) {
+			pr_warn("No \"interrupts\" property.\n");
+			return r;
+		}
+		base_hwirq = (v0 << 6) | v1;
+	} else {
+		pr_warn("Bad \"#interrupt-cells\" property: %u\n",
+			interrupt_cells);
+		return -EINVAL;
+	}
+
+	gpiod = kzalloc(sizeof(*gpiod), GFP_KERNEL);
+	if (gpiod) {
+		/* gpio domain host_data is the base hwirq number. */
+		gpiod->base_hwirq = base_hwirq;
+		irq_domain_add_linear(
+			gpio_node, 16, &octeon_irq_domain_gpio_ops, gpiod);
+	} else {
+		pr_warn("Cannot allocate memory for GPIO irq_domain.\n");
+		return -ENOMEM;
+	}
+
+	/*
+	 * Clear the OF_POPULATED flag that was set by of_irq_init()
+	 * so that all GPIO devices will be probed.
+	 */
+	of_node_clear_flag(gpio_node, OF_POPULATED);
+
+	return 0;
+}
+/*
+ * Watchdog interrupts are special.  They are associated with a single
+ * core, so we hardwire the affinity to that core.
+ */
+static void octeon_irq_ciu2_wd_enable(struct irq_data *data)
+{
+	u64 mask;
+	u64 en_addr;
+	int coreid = data->irq - OCTEON_IRQ_WDOG0;
+	struct octeon_ciu_chip_data *cd;
+
+	cd = irq_data_get_irq_chip_data(data);
+	mask = 1ull << (cd->bit);
+
+	en_addr = CVMX_CIU2_EN_PPX_IP2_WRKQ_W1S(coreid) +
+		(0x1000ull * cd->line);
+	cvmx_write_csr(en_addr, mask);
+
+}
+
+static void octeon_irq_ciu2_enable(struct irq_data *data)
+{
+	u64 mask;
+	u64 en_addr;
+	int cpu = next_cpu_for_irq(data);
+	int coreid = octeon_coreid_for_cpu(cpu);
+	struct octeon_ciu_chip_data *cd;
+
+	cd = irq_data_get_irq_chip_data(data);
+	mask = 1ull << (cd->bit);
+
+	en_addr = CVMX_CIU2_EN_PPX_IP2_WRKQ_W1S(coreid) +
+		(0x1000ull * cd->line);
+	cvmx_write_csr(en_addr, mask);
+}
+
+static void octeon_irq_ciu2_enable_local(struct irq_data *data)
+{
+	u64 mask;
+	u64 en_addr;
+	int coreid = cvmx_get_core_num();
+	struct octeon_ciu_chip_data *cd;
+
+	cd = irq_data_get_irq_chip_data(data);
+	mask = 1ull << (cd->bit);
+
+	en_addr = CVMX_CIU2_EN_PPX_IP2_WRKQ_W1S(coreid) +
+		(0x1000ull * cd->line);
+	cvmx_write_csr(en_addr, mask);
+
+}
+
+static void octeon_irq_ciu2_disable_local(struct irq_data *data)
+{
+	u64 mask;
+	u64 en_addr;
+	int coreid = cvmx_get_core_num();
+	struct octeon_ciu_chip_data *cd;
+
+	cd = irq_data_get_irq_chip_data(data);
+	mask = 1ull << (cd->bit);
+
+	en_addr = CVMX_CIU2_EN_PPX_IP2_WRKQ_W1C(coreid) +
+		(0x1000ull * cd->line);
+	cvmx_write_csr(en_addr, mask);
+
+}
+
+static void octeon_irq_ciu2_ack(struct irq_data *data)
+{
+	u64 mask;
+	u64 en_addr;
+	int coreid = cvmx_get_core_num();
+	struct octeon_ciu_chip_data *cd;
+
+	cd = irq_data_get_irq_chip_data(data);
+	mask = 1ull << (cd->bit);
+
+	en_addr = CVMX_CIU2_RAW_PPX_IP2_WRKQ(coreid) + (0x1000ull * cd->line);
+	cvmx_write_csr(en_addr, mask);
+
+}
+
+static void octeon_irq_ciu2_disable_all(struct irq_data *data)
+{
+	int cpu;
+	u64 mask;
+	struct octeon_ciu_chip_data *cd;
+
+	cd = irq_data_get_irq_chip_data(data);
+	mask = 1ull << (cd->bit);
+
+	for_each_online_cpu(cpu) {
+		u64 en_addr = CVMX_CIU2_EN_PPX_IP2_WRKQ_W1C(
+			octeon_coreid_for_cpu(cpu)) + (0x1000ull * cd->line);
+		cvmx_write_csr(en_addr, mask);
+	}
+}
+
+static void octeon_irq_ciu2_mbox_enable_all(struct irq_data *data)
+{
+	int cpu;
+	u64 mask;
+
+	mask = 1ull << (data->irq - OCTEON_IRQ_MBOX0);
+
+	for_each_online_cpu(cpu) {
+		u64 en_addr = CVMX_CIU2_EN_PPX_IP3_MBOX_W1S(
+			octeon_coreid_for_cpu(cpu));
+		cvmx_write_csr(en_addr, mask);
+	}
+}
+
+static void octeon_irq_ciu2_mbox_disable_all(struct irq_data *data)
+{
+	int cpu;
+	u64 mask;
+
+	mask = 1ull << (data->irq - OCTEON_IRQ_MBOX0);
+
+	for_each_online_cpu(cpu) {
+		u64 en_addr = CVMX_CIU2_EN_PPX_IP3_MBOX_W1C(
+			octeon_coreid_for_cpu(cpu));
+		cvmx_write_csr(en_addr, mask);
+	}
+}
+
+static void octeon_irq_ciu2_mbox_enable_local(struct irq_data *data)
+{
+	u64 mask;
+	u64 en_addr;
+	int coreid = cvmx_get_core_num();
+
+	mask = 1ull << (data->irq - OCTEON_IRQ_MBOX0);
+	en_addr = CVMX_CIU2_EN_PPX_IP3_MBOX_W1S(coreid);
+	cvmx_write_csr(en_addr, mask);
+}
+
+static void octeon_irq_ciu2_mbox_disable_local(struct irq_data *data)
+{
+	u64 mask;
+	u64 en_addr;
+	int coreid = cvmx_get_core_num();
+
+	mask = 1ull << (data->irq - OCTEON_IRQ_MBOX0);
+	en_addr = CVMX_CIU2_EN_PPX_IP3_MBOX_W1C(coreid);
+	cvmx_write_csr(en_addr, mask);
+}
+
+#ifdef CONFIG_SMP
+static int octeon_irq_ciu2_set_affinity(struct irq_data *data,
+					const struct cpumask *dest, bool force)
+{
+	int cpu;
+	bool enable_one = !irqd_irq_disabled(data) && !irqd_irq_masked(data);
+	u64 mask;
+	struct octeon_ciu_chip_data *cd;
+
+	if (!enable_one)
+		return 0;
+
+	cd = irq_data_get_irq_chip_data(data);
+	mask = 1ull << cd->bit;
+
+	for_each_online_cpu(cpu) {
+		u64 en_addr;
+		if (cpumask_test_cpu(cpu, dest) && enable_one) {
+			enable_one = false;
+			en_addr = CVMX_CIU2_EN_PPX_IP2_WRKQ_W1S(
+				octeon_coreid_for_cpu(cpu)) +
+				(0x1000ull * cd->line);
+		} else {
+			en_addr = CVMX_CIU2_EN_PPX_IP2_WRKQ_W1C(
+				octeon_coreid_for_cpu(cpu)) +
+				(0x1000ull * cd->line);
+		}
+		cvmx_write_csr(en_addr, mask);
+	}
+
+	return 0;
+}
+#endif
+
+static void octeon_irq_ciu2_enable_gpio(struct irq_data *data)
+{
+	octeon_irq_gpio_setup(data);
+	octeon_irq_ciu2_enable(data);
+}
+
+static void octeon_irq_ciu2_disable_gpio(struct irq_data *data)
+{
+	struct octeon_ciu_chip_data *cd;
+
+	cd = irq_data_get_irq_chip_data(data);
+
+	cvmx_write_csr(CVMX_GPIO_BIT_CFGX(cd->gpio_line), 0);
+
+	octeon_irq_ciu2_disable_all(data);
+}
+
+static struct irq_chip octeon_irq_chip_ciu2 = {
+	.name = "CIU2-E",
+	.irq_enable = octeon_irq_ciu2_enable,
+	.irq_disable = octeon_irq_ciu2_disable_all,
+	.irq_mask = octeon_irq_ciu2_disable_local,
+	.irq_unmask = octeon_irq_ciu2_enable,
+#ifdef CONFIG_SMP
+	.irq_set_affinity = octeon_irq_ciu2_set_affinity,
+	.irq_cpu_offline = octeon_irq_cpu_offline_ciu,
+#endif
+};
+
+static struct irq_chip octeon_irq_chip_ciu2_edge = {
+	.name = "CIU2-E",
+	.irq_enable = octeon_irq_ciu2_enable,
+	.irq_disable = octeon_irq_ciu2_disable_all,
+	.irq_ack = octeon_irq_ciu2_ack,
+	.irq_mask = octeon_irq_ciu2_disable_local,
+	.irq_unmask = octeon_irq_ciu2_enable,
+#ifdef CONFIG_SMP
+	.irq_set_affinity = octeon_irq_ciu2_set_affinity,
+	.irq_cpu_offline = octeon_irq_cpu_offline_ciu,
+#endif
+};
+
+static struct irq_chip octeon_irq_chip_ciu2_mbox = {
+	.name = "CIU2-M",
+	.irq_enable = octeon_irq_ciu2_mbox_enable_all,
+	.irq_disable = octeon_irq_ciu2_mbox_disable_all,
+	.irq_ack = octeon_irq_ciu2_mbox_disable_local,
+	.irq_eoi = octeon_irq_ciu2_mbox_enable_local,
+
+	.irq_cpu_online = octeon_irq_ciu2_mbox_enable_local,
+	.irq_cpu_offline = octeon_irq_ciu2_mbox_disable_local,
+	.flags = IRQCHIP_ONOFFLINE_ENABLED,
+};
+
+static struct irq_chip octeon_irq_chip_ciu2_wd = {
+	.name = "CIU2-W",
+	.irq_enable = octeon_irq_ciu2_wd_enable,
+	.irq_disable = octeon_irq_ciu2_disable_all,
+	.irq_mask = octeon_irq_ciu2_disable_local,
+	.irq_unmask = octeon_irq_ciu2_enable_local,
+};
+
+static struct irq_chip octeon_irq_chip_ciu2_gpio = {
+	.name = "CIU-GPIO",
+	.irq_enable = octeon_irq_ciu2_enable_gpio,
+	.irq_disable = octeon_irq_ciu2_disable_gpio,
+	.irq_ack = octeon_irq_ciu_gpio_ack,
+	.irq_mask = octeon_irq_ciu2_disable_local,
+	.irq_unmask = octeon_irq_ciu2_enable,
+	.irq_set_type = octeon_irq_ciu_gpio_set_type,
+#ifdef CONFIG_SMP
+	.irq_set_affinity = octeon_irq_ciu2_set_affinity,
+	.irq_cpu_offline = octeon_irq_cpu_offline_ciu,
+#endif
+	.flags = IRQCHIP_SET_TYPE_MASKED,
+};
+
+static int octeon_irq_ciu2_xlat(struct irq_domain *d,
+				struct device_node *node,
+				const u32 *intspec,
+				unsigned int intsize,
+				unsigned long *out_hwirq,
+				unsigned int *out_type)
+{
+	unsigned int ciu, bit;
+
+	ciu = intspec[0];
+	bit = intspec[1];
+
+	*out_hwirq = (ciu << 6) | bit;
+	*out_type = 0;
+
+	return 0;
+}
+
+static bool octeon_irq_ciu2_is_edge(unsigned int line, unsigned int bit)
+{
+	bool edge = false;
+
+	if (line == 3) /* MIO */
+		switch (bit) {
+		case 2:	 /* IPD_DRP */
+		case 8 ... 11: /* Timers */
+		case 48: /* PTP */
+			edge = true;
+			break;
+		default:
+			break;
+		}
+	else if (line == 6) /* PKT */
+		switch (bit) {
+		case 52 ... 53: /* ILK_DRP */
+		case 8 ... 12:	/* GMX_DRP */
+			edge = true;
+			break;
+		default:
+			break;
+		}
+	return edge;
+}
+
+static int octeon_irq_ciu2_map(struct irq_domain *d,
+			       unsigned int virq, irq_hw_number_t hw)
+{
+	unsigned int line = hw >> 6;
+	unsigned int bit = hw & 63;
+
+	/*
+	 * Don't map irq if it is reserved for GPIO.
+	 * (Line 7 are the GPIO lines.)
+	 */
+	if (line == 7)
+		return 0;
+
+	if (line > 7 || octeon_irq_ciu_to_irq[line][bit] != 0)
+		return -EINVAL;
+
+	if (octeon_irq_ciu2_is_edge(line, bit))
+		octeon_irq_set_ciu_mapping(virq, line, bit, 0,
+					   &octeon_irq_chip_ciu2_edge,
+					   handle_edge_irq);
+	else
+		octeon_irq_set_ciu_mapping(virq, line, bit, 0,
+					   &octeon_irq_chip_ciu2,
+					   handle_level_irq);
+
+	return 0;
+}
+
+static const struct irq_domain_ops octeon_irq_domain_ciu2_ops = {
+	.map = octeon_irq_ciu2_map,
+	.unmap = octeon_irq_free_cd,
+	.xlate = octeon_irq_ciu2_xlat,
+};
+
+static void octeon_irq_ciu2(void)
+{
+	int line;
+	int bit;
+	int irq;
+	u64 src_reg, src, sum;
+	const unsigned long core_id = cvmx_get_core_num();
+
+	sum = cvmx_read_csr(CVMX_CIU2_SUM_PPX_IP2(core_id)) & 0xfful;
+
+	if (unlikely(!sum))
+		goto spurious;
+
+	line = fls64(sum) - 1;
+	src_reg = CVMX_CIU2_SRC_PPX_IP2_WRKQ(core_id) + (0x1000 * line);
+	src = cvmx_read_csr(src_reg);
+
+	if (unlikely(!src))
+		goto spurious;
+
+	bit = fls64(src) - 1;
+	irq = octeon_irq_ciu_to_irq[line][bit];
+	if (unlikely(!irq))
+		goto spurious;
+
+	do_IRQ(irq);
+	goto out;
+
+spurious:
+	spurious_interrupt();
+out:
+	/* CN68XX pass 1.x has an errata that accessing the ACK registers
+		can stop interrupts from propagating */
+	if (OCTEON_IS_MODEL(OCTEON_CN68XX))
+		cvmx_read_csr(CVMX_CIU2_INTR_CIU_READY);
+	else
+		cvmx_read_csr(CVMX_CIU2_ACK_PPX_IP2(core_id));
+	return;
+}
+
+static void octeon_irq_ciu2_mbox(void)
+{
+	int line;
+
+	const unsigned long core_id = cvmx_get_core_num();
+	u64 sum = cvmx_read_csr(CVMX_CIU2_SUM_PPX_IP3(core_id)) >> 60;
+
+	if (unlikely(!sum))
+		goto spurious;
+
+	line = fls64(sum) - 1;
+
+	do_IRQ(OCTEON_IRQ_MBOX0 + line);
+	goto out;
+
+spurious:
+	spurious_interrupt();
+out:
+	/* CN68XX pass 1.x has an errata that accessing the ACK registers
+		can stop interrupts from propagating */
+	if (OCTEON_IS_MODEL(OCTEON_CN68XX))
+		cvmx_read_csr(CVMX_CIU2_INTR_CIU_READY);
+	else
+		cvmx_read_csr(CVMX_CIU2_ACK_PPX_IP3(core_id));
+	return;
+}
+
+static int __init octeon_irq_init_ciu2(
+	struct device_node *ciu_node, struct device_node *parent)
+{
+	unsigned int i, r;
+	struct irq_domain *ciu_domain = NULL;
+
+	octeon_irq_init_ciu2_percpu();
+	octeon_irq_setup_secondary = octeon_irq_setup_secondary_ciu2;
+
+	octeon_irq_gpio_chip = &octeon_irq_chip_ciu2_gpio;
+	octeon_irq_ip2 = octeon_irq_ciu2;
+	octeon_irq_ip3 = octeon_irq_ciu2_mbox;
+	octeon_irq_ip4 = octeon_irq_ip4_mask;
+
+	/* Mips internal */
+	octeon_irq_init_core();
+
+	ciu_domain = irq_domain_add_tree(
+		ciu_node, &octeon_irq_domain_ciu2_ops, NULL);
+	irq_set_default_host(ciu_domain);
+
+	/* CUI2 */
+	for (i = 0; i < 64; i++) {
+		r = octeon_irq_force_ciu_mapping(
+			ciu_domain, i + OCTEON_IRQ_WORKQ0, 0, i);
+		if (r)
+			goto err;
+	}
+
+	for (i = 0; i < 32; i++) {
+		r = octeon_irq_set_ciu_mapping(i + OCTEON_IRQ_WDOG0, 1, i, 0,
+			&octeon_irq_chip_ciu2_wd, handle_level_irq);
+		if (r)
+			goto err;
+	}
+
+	for (i = 0; i < 4; i++) {
+		r = octeon_irq_force_ciu_mapping(
+			ciu_domain, i + OCTEON_IRQ_TIMER0, 3, i + 8);
+		if (r)
+			goto err;
+	}
+
+	for (i = 0; i < 4; i++) {
+		r = octeon_irq_force_ciu_mapping(
+			ciu_domain, i + OCTEON_IRQ_PCI_INT0, 4, i);
+		if (r)
+			goto err;
+	}
+
+	for (i = 0; i < 4; i++) {
+		r = octeon_irq_force_ciu_mapping(
+			ciu_domain, i + OCTEON_IRQ_PCI_MSI0, 4, i + 8);
+		if (r)
+			goto err;
+	}
+
+	irq_set_chip_and_handler(OCTEON_IRQ_MBOX0, &octeon_irq_chip_ciu2_mbox, handle_percpu_irq);
+	irq_set_chip_and_handler(OCTEON_IRQ_MBOX1, &octeon_irq_chip_ciu2_mbox, handle_percpu_irq);
+	irq_set_chip_and_handler(OCTEON_IRQ_MBOX2, &octeon_irq_chip_ciu2_mbox, handle_percpu_irq);
+	irq_set_chip_and_handler(OCTEON_IRQ_MBOX3, &octeon_irq_chip_ciu2_mbox, handle_percpu_irq);
+
+	/* Enable the CIU lines */
+	set_c0_status(STATUSF_IP3 | STATUSF_IP2);
+	clear_c0_status(STATUSF_IP4);
+	return 0;
+err:
+	return r;
+}
+
+struct octeon_irq_cib_host_data {
+	raw_spinlock_t lock;
+	u64 raw_reg;
+	u64 en_reg;
+	int max_bits;
+};
+
+struct octeon_irq_cib_chip_data {
+	struct octeon_irq_cib_host_data *host_data;
+	int bit;
+};
+
+static void octeon_irq_cib_enable(struct irq_data *data)
+{
+	unsigned long flags;
+	u64 en;
+	struct octeon_irq_cib_chip_data *cd = irq_data_get_irq_chip_data(data);
+	struct octeon_irq_cib_host_data *host_data = cd->host_data;
+
+	raw_spin_lock_irqsave(&host_data->lock, flags);
+	en = cvmx_read_csr(host_data->en_reg);
+	en |= 1ull << cd->bit;
+	cvmx_write_csr(host_data->en_reg, en);
+	raw_spin_unlock_irqrestore(&host_data->lock, flags);
+}
+
+static void octeon_irq_cib_disable(struct irq_data *data)
+{
+	unsigned long flags;
+	u64 en;
+	struct octeon_irq_cib_chip_data *cd = irq_data_get_irq_chip_data(data);
+	struct octeon_irq_cib_host_data *host_data = cd->host_data;
+
+	raw_spin_lock_irqsave(&host_data->lock, flags);
+	en = cvmx_read_csr(host_data->en_reg);
+	en &= ~(1ull << cd->bit);
+	cvmx_write_csr(host_data->en_reg, en);
+	raw_spin_unlock_irqrestore(&host_data->lock, flags);
+}
+
+static int octeon_irq_cib_set_type(struct irq_data *data, unsigned int t)
+{
+	irqd_set_trigger_type(data, t);
+	return IRQ_SET_MASK_OK;
+}
+
+static struct irq_chip octeon_irq_chip_cib = {
+	.name = "CIB",
+	.irq_enable = octeon_irq_cib_enable,
+	.irq_disable = octeon_irq_cib_disable,
+	.irq_mask = octeon_irq_cib_disable,
+	.irq_unmask = octeon_irq_cib_enable,
+	.irq_set_type = octeon_irq_cib_set_type,
+};
+
+static int octeon_irq_cib_xlat(struct irq_domain *d,
+				   struct device_node *node,
+				   const u32 *intspec,
+				   unsigned int intsize,
+				   unsigned long *out_hwirq,
+				   unsigned int *out_type)
+{
+	unsigned int type = 0;
+
+	if (intsize == 2)
+		type = intspec[1];
+
+	switch (type) {
+	case 0: /* unofficial value, but we might as well let it work. */
+	case 4: /* official value for level triggering. */
+		*out_type = IRQ_TYPE_LEVEL_HIGH;
+		break;
+	case 1: /* official value for edge triggering. */
+		*out_type = IRQ_TYPE_EDGE_RISING;
+		break;
+	default: /* Nothing else is acceptable. */
+		return -EINVAL;
+	}
+
+	*out_hwirq = intspec[0];
+
+	return 0;
+}
+
+static int octeon_irq_cib_map(struct irq_domain *d,
+			      unsigned int virq, irq_hw_number_t hw)
+{
+	struct octeon_irq_cib_host_data *host_data = d->host_data;
+	struct octeon_irq_cib_chip_data *cd;
+
+	if (hw >= host_data->max_bits) {
+		pr_err("ERROR: %s mapping %u is too big!\n",
+		       irq_domain_get_of_node(d)->name, (unsigned)hw);
+		return -EINVAL;
+	}
+
+	cd = kzalloc(sizeof(*cd), GFP_KERNEL);
+	if (!cd)
+		return -ENOMEM;
+
+	cd->host_data = host_data;
+	cd->bit = hw;
+
+	irq_set_chip_and_handler(virq, &octeon_irq_chip_cib,
+				 handle_simple_irq);
+	irq_set_chip_data(virq, cd);
+	return 0;
+}
+
+static const struct irq_domain_ops octeon_irq_domain_cib_ops = {
+	.map = octeon_irq_cib_map,
+	.unmap = octeon_irq_free_cd,
+	.xlate = octeon_irq_cib_xlat,
+};
+
+/* Chain to real handler. */
+static irqreturn_t octeon_irq_cib_handler(int my_irq, void *data)
+{
+	u64 en;
+	u64 raw;
+	u64 bits;
+	int i;
+	int irq;
+	struct irq_domain *cib_domain = data;
+	struct octeon_irq_cib_host_data *host_data = cib_domain->host_data;
+
+	en = cvmx_read_csr(host_data->en_reg);
+	raw = cvmx_read_csr(host_data->raw_reg);
+
+	bits = en & raw;
+
+	for (i = 0; i < host_data->max_bits; i++) {
+		if ((bits & 1ull << i) == 0)
+			continue;
+		irq = irq_find_mapping(cib_domain, i);
+		if (!irq) {
+			unsigned long flags;
+
+			pr_err("ERROR: CIB bit %d@%llx IRQ unhandled, disabling\n",
+				i, host_data->raw_reg);
+			raw_spin_lock_irqsave(&host_data->lock, flags);
+			en = cvmx_read_csr(host_data->en_reg);
+			en &= ~(1ull << i);
+			cvmx_write_csr(host_data->en_reg, en);
+			cvmx_write_csr(host_data->raw_reg, 1ull << i);
+			raw_spin_unlock_irqrestore(&host_data->lock, flags);
+		} else {
+			struct irq_desc *desc = irq_to_desc(irq);
+			struct irq_data *irq_data = irq_desc_get_irq_data(desc);
+			/* If edge, acknowledge the bit we will be sending. */
+			if (irqd_get_trigger_type(irq_data) &
+				IRQ_TYPE_EDGE_BOTH)
+				cvmx_write_csr(host_data->raw_reg, 1ull << i);
+			generic_handle_irq_desc(desc);
+		}
+	}
+
+	return IRQ_HANDLED;
+}
+
+static int __init octeon_irq_init_cib(struct device_node *ciu_node,
+				      struct device_node *parent)
+{
+	const __be32 *addr;
+	u32 val;
+	struct octeon_irq_cib_host_data *host_data;
+	int parent_irq;
+	int r;
+	struct irq_domain *cib_domain;
+
+	parent_irq = irq_of_parse_and_map(ciu_node, 0);
+	if (!parent_irq) {
+		pr_err("ERROR: Couldn't acquire parent_irq for %pOFn\n",
+			ciu_node);
+		return -EINVAL;
+	}
+
+	host_data = kzalloc(sizeof(*host_data), GFP_KERNEL);
+	if (!host_data)
+		return -ENOMEM;
+	raw_spin_lock_init(&host_data->lock);
+
+	addr = of_get_address(ciu_node, 0, NULL, NULL);
+	if (!addr) {
+		pr_err("ERROR: Couldn't acquire reg(0) %pOFn\n", ciu_node);
+		return -EINVAL;
+	}
+	host_data->raw_reg = (u64)phys_to_virt(
+		of_translate_address(ciu_node, addr));
+
+	addr = of_get_address(ciu_node, 1, NULL, NULL);
+	if (!addr) {
+		pr_err("ERROR: Couldn't acquire reg(1) %pOFn\n", ciu_node);
+		return -EINVAL;
+	}
+	host_data->en_reg = (u64)phys_to_virt(
+		of_translate_address(ciu_node, addr));
+
+	r = of_property_read_u32(ciu_node, "cavium,max-bits", &val);
+	if (r) {
+		pr_err("ERROR: Couldn't read cavium,max-bits from %pOFn\n",
+			ciu_node);
+		return r;
+	}
+	host_data->max_bits = val;
+
+	cib_domain = irq_domain_add_linear(ciu_node, host_data->max_bits,
+					   &octeon_irq_domain_cib_ops,
+					   host_data);
+	if (!cib_domain) {
+		pr_err("ERROR: Couldn't irq_domain_add_linear()\n");
+		return -ENOMEM;
+	}
+
+	cvmx_write_csr(host_data->en_reg, 0); /* disable all IRQs */
+	cvmx_write_csr(host_data->raw_reg, ~0); /* ack any outstanding */
+
+	r = request_irq(parent_irq, octeon_irq_cib_handler,
+			IRQF_NO_THREAD, "cib", cib_domain);
+	if (r) {
+		pr_err("request_irq cib failed %d\n", r);
+		return r;
+	}
+	pr_info("CIB interrupt controller probed: %llx %d\n",
+		host_data->raw_reg, host_data->max_bits);
+	return 0;
+}
+
+int octeon_irq_ciu3_xlat(struct irq_domain *d,
+			 struct device_node *node,
+			 const u32 *intspec,
+			 unsigned int intsize,
+			 unsigned long *out_hwirq,
+			 unsigned int *out_type)
+{
+	struct octeon_ciu3_info *ciu3_info = d->host_data;
+	unsigned int hwirq, type, intsn_major;
+	union cvmx_ciu3_iscx_ctl isc;
+
+	if (intsize < 2)
+		return -EINVAL;
+	hwirq = intspec[0];
+	type = intspec[1];
+
+	if (hwirq >= (1 << 20))
+		return -EINVAL;
+
+	intsn_major = hwirq >> 12;
+	switch (intsn_major) {
+	case 0x04: /* Software handled separately. */
+		return -EINVAL;
+	default:
+		break;
+	}
+
+	isc.u64 =  cvmx_read_csr(ciu3_info->ciu3_addr + CIU3_ISC_CTL(hwirq));
+	if (!isc.s.imp)
+		return -EINVAL;
+
+	switch (type) {
+	case 4: /* official value for level triggering. */
+		*out_type = IRQ_TYPE_LEVEL_HIGH;
+		break;
+	case 0: /* unofficial value, but we might as well let it work. */
+	case 1: /* official value for edge triggering. */
+		*out_type = IRQ_TYPE_EDGE_RISING;
+		break;
+	default: /* Nothing else is acceptable. */
+		return -EINVAL;
+	}
+
+	*out_hwirq = hwirq;
+
+	return 0;
+}
+
+void octeon_irq_ciu3_enable(struct irq_data *data)
+{
+	int cpu;
+	union cvmx_ciu3_iscx_ctl isc_ctl;
+	union cvmx_ciu3_iscx_w1c isc_w1c;
+	u64 isc_ctl_addr;
+
+	struct octeon_ciu_chip_data *cd;
+
+	cpu = next_cpu_for_irq(data);
+
+	cd = irq_data_get_irq_chip_data(data);
+
+	isc_w1c.u64 = 0;
+	isc_w1c.s.en = 1;
+	cvmx_write_csr(cd->ciu3_addr + CIU3_ISC_W1C(cd->intsn), isc_w1c.u64);
+
+	isc_ctl_addr = cd->ciu3_addr + CIU3_ISC_CTL(cd->intsn);
+	isc_ctl.u64 = 0;
+	isc_ctl.s.en = 1;
+	isc_ctl.s.idt = per_cpu(octeon_irq_ciu3_idt_ip2, cpu);
+	cvmx_write_csr(isc_ctl_addr, isc_ctl.u64);
+	cvmx_read_csr(isc_ctl_addr);
+}
+
+void octeon_irq_ciu3_disable(struct irq_data *data)
+{
+	u64 isc_ctl_addr;
+	union cvmx_ciu3_iscx_w1c isc_w1c;
+
+	struct octeon_ciu_chip_data *cd;
+
+	cd = irq_data_get_irq_chip_data(data);
+
+	isc_w1c.u64 = 0;
+	isc_w1c.s.en = 1;
+
+	isc_ctl_addr = cd->ciu3_addr + CIU3_ISC_CTL(cd->intsn);
+	cvmx_write_csr(cd->ciu3_addr + CIU3_ISC_W1C(cd->intsn), isc_w1c.u64);
+	cvmx_write_csr(isc_ctl_addr, 0);
+	cvmx_read_csr(isc_ctl_addr);
+}
+
+void octeon_irq_ciu3_ack(struct irq_data *data)
+{
+	u64 isc_w1c_addr;
+	union cvmx_ciu3_iscx_w1c isc_w1c;
+	struct octeon_ciu_chip_data *cd;
+	u32 trigger_type = irqd_get_trigger_type(data);
+
+	/*
+	 * We use a single irq_chip, so we have to do nothing to ack a
+	 * level interrupt.
+	 */
+	if (!(trigger_type & IRQ_TYPE_EDGE_BOTH))
+		return;
+
+	cd = irq_data_get_irq_chip_data(data);
+
+	isc_w1c.u64 = 0;
+	isc_w1c.s.raw = 1;
+
+	isc_w1c_addr = cd->ciu3_addr + CIU3_ISC_W1C(cd->intsn);
+	cvmx_write_csr(isc_w1c_addr, isc_w1c.u64);
+	cvmx_read_csr(isc_w1c_addr);
+}
+
+void octeon_irq_ciu3_mask(struct irq_data *data)
+{
+	union cvmx_ciu3_iscx_w1c isc_w1c;
+	u64 isc_w1c_addr;
+	struct octeon_ciu_chip_data *cd;
+
+	cd = irq_data_get_irq_chip_data(data);
+
+	isc_w1c.u64 = 0;
+	isc_w1c.s.en = 1;
+
+	isc_w1c_addr = cd->ciu3_addr + CIU3_ISC_W1C(cd->intsn);
+	cvmx_write_csr(isc_w1c_addr, isc_w1c.u64);
+	cvmx_read_csr(isc_w1c_addr);
+}
+
+void octeon_irq_ciu3_mask_ack(struct irq_data *data)
+{
+	union cvmx_ciu3_iscx_w1c isc_w1c;
+	u64 isc_w1c_addr;
+	struct octeon_ciu_chip_data *cd;
+	u32 trigger_type = irqd_get_trigger_type(data);
+
+	cd = irq_data_get_irq_chip_data(data);
+
+	isc_w1c.u64 = 0;
+	isc_w1c.s.en = 1;
+
+	/*
+	 * We use a single irq_chip, so only ack an edge (!level)
+	 * interrupt.
+	 */
+	if (trigger_type & IRQ_TYPE_EDGE_BOTH)
+		isc_w1c.s.raw = 1;
+
+	isc_w1c_addr = cd->ciu3_addr + CIU3_ISC_W1C(cd->intsn);
+	cvmx_write_csr(isc_w1c_addr, isc_w1c.u64);
+	cvmx_read_csr(isc_w1c_addr);
+}
+
+#ifdef CONFIG_SMP
+static int octeon_irq_ciu3_set_affinity(struct irq_data *data,
+					const struct cpumask *dest, bool force)
+{
+	union cvmx_ciu3_iscx_ctl isc_ctl;
+	union cvmx_ciu3_iscx_w1c isc_w1c;
+	u64 isc_ctl_addr;
+	int cpu;
+	bool enable_one = !irqd_irq_disabled(data) && !irqd_irq_masked(data);
+	struct octeon_ciu_chip_data *cd = irq_data_get_irq_chip_data(data);
+
+	if (!cpumask_subset(dest, cpumask_of_node(cd->ciu_node)))
+		return -EINVAL;
+
+	if (!enable_one)
+		return IRQ_SET_MASK_OK;
+
+	cd = irq_data_get_irq_chip_data(data);
+	cpu = cpumask_first(dest);
+	if (cpu >= nr_cpu_ids)
+		cpu = smp_processor_id();
+	cd->current_cpu = cpu;
+
+	isc_w1c.u64 = 0;
+	isc_w1c.s.en = 1;
+	cvmx_write_csr(cd->ciu3_addr + CIU3_ISC_W1C(cd->intsn), isc_w1c.u64);
+
+	isc_ctl_addr = cd->ciu3_addr + CIU3_ISC_CTL(cd->intsn);
+	isc_ctl.u64 = 0;
+	isc_ctl.s.en = 1;
+	isc_ctl.s.idt = per_cpu(octeon_irq_ciu3_idt_ip2, cpu);
+	cvmx_write_csr(isc_ctl_addr, isc_ctl.u64);
+	cvmx_read_csr(isc_ctl_addr);
+
+	return IRQ_SET_MASK_OK;
+}
+#endif
+
+static struct irq_chip octeon_irq_chip_ciu3 = {
+	.name = "CIU3",
+	.irq_startup = edge_startup,
+	.irq_enable = octeon_irq_ciu3_enable,
+	.irq_disable = octeon_irq_ciu3_disable,
+	.irq_ack = octeon_irq_ciu3_ack,
+	.irq_mask = octeon_irq_ciu3_mask,
+	.irq_mask_ack = octeon_irq_ciu3_mask_ack,
+	.irq_unmask = octeon_irq_ciu3_enable,
+	.irq_set_type = octeon_irq_ciu_set_type,
+#ifdef CONFIG_SMP
+	.irq_set_affinity = octeon_irq_ciu3_set_affinity,
+	.irq_cpu_offline = octeon_irq_cpu_offline_ciu,
+#endif
+};
+
+int octeon_irq_ciu3_mapx(struct irq_domain *d, unsigned int virq,
+			 irq_hw_number_t hw, struct irq_chip *chip)
+{
+	struct octeon_ciu3_info *ciu3_info = d->host_data;
+	struct octeon_ciu_chip_data *cd = kzalloc_node(sizeof(*cd), GFP_KERNEL,
+						       ciu3_info->node);
+	if (!cd)
+		return -ENOMEM;
+	cd->intsn = hw;
+	cd->current_cpu = -1;
+	cd->ciu3_addr = ciu3_info->ciu3_addr;
+	cd->ciu_node = ciu3_info->node;
+	irq_set_chip_and_handler(virq, chip, handle_edge_irq);
+	irq_set_chip_data(virq, cd);
+
+	return 0;
+}
+
+static int octeon_irq_ciu3_map(struct irq_domain *d,
+			       unsigned int virq, irq_hw_number_t hw)
+{
+	return octeon_irq_ciu3_mapx(d, virq, hw, &octeon_irq_chip_ciu3);
+}
+
+static const struct irq_domain_ops octeon_dflt_domain_ciu3_ops = {
+	.map = octeon_irq_ciu3_map,
+	.unmap = octeon_irq_free_cd,
+	.xlate = octeon_irq_ciu3_xlat,
+};
+
+static void octeon_irq_ciu3_ip2(void)
+{
+	union cvmx_ciu3_destx_pp_int dest_pp_int;
+	struct octeon_ciu3_info *ciu3_info;
+	u64 ciu3_addr;
+
+	ciu3_info = __this_cpu_read(octeon_ciu3_info);
+	ciu3_addr = ciu3_info->ciu3_addr;
+
+	dest_pp_int.u64 = cvmx_read_csr(ciu3_addr + CIU3_DEST_PP_INT(3 * cvmx_get_local_core_num()));
+
+	if (likely(dest_pp_int.s.intr)) {
+		irq_hw_number_t intsn = dest_pp_int.s.intsn;
+		irq_hw_number_t hw;
+		struct irq_domain *domain;
+		/* Get the domain to use from the major block */
+		int block = intsn >> 12;
+		int ret;
+
+		domain = ciu3_info->domain[block];
+		if (ciu3_info->intsn2hw[block])
+			hw = ciu3_info->intsn2hw[block](domain, intsn);
+		else
+			hw = intsn;
+
+		irq_enter();
+		ret = generic_handle_domain_irq(domain, hw);
+		irq_exit();
+
+		if (ret < 0) {
+			union cvmx_ciu3_iscx_w1c isc_w1c;
+			u64 isc_w1c_addr = ciu3_addr + CIU3_ISC_W1C(intsn);
+
+			isc_w1c.u64 = 0;
+			isc_w1c.s.en = 1;
+			cvmx_write_csr(isc_w1c_addr, isc_w1c.u64);
+			cvmx_read_csr(isc_w1c_addr);
+			spurious_interrupt();
+		}
+	} else {
+		spurious_interrupt();
+	}
+}
+
+/*
+ * 10 mbox per core starting from zero.
+ * Base mbox is core * 10
+ */
+static unsigned int octeon_irq_ciu3_base_mbox_intsn(int core)
+{
+	/* SW (mbox) are 0x04 in bits 12..19 */
+	return 0x04000 + CIU3_MBOX_PER_CORE * core;
+}
+
+static unsigned int octeon_irq_ciu3_mbox_intsn_for_core(int core, unsigned int mbox)
+{
+	return octeon_irq_ciu3_base_mbox_intsn(core) + mbox;
+}
+
+static unsigned int octeon_irq_ciu3_mbox_intsn_for_cpu(int cpu, unsigned int mbox)
+{
+	int local_core = octeon_coreid_for_cpu(cpu) & 0x3f;
+
+	return octeon_irq_ciu3_mbox_intsn_for_core(local_core, mbox);
+}
+
+static void octeon_irq_ciu3_mbox(void)
+{
+	union cvmx_ciu3_destx_pp_int dest_pp_int;
+	struct octeon_ciu3_info *ciu3_info;
+	u64 ciu3_addr;
+	int core = cvmx_get_local_core_num();
+
+	ciu3_info = __this_cpu_read(octeon_ciu3_info);
+	ciu3_addr = ciu3_info->ciu3_addr;
+
+	dest_pp_int.u64 = cvmx_read_csr(ciu3_addr + CIU3_DEST_PP_INT(1 + 3 * core));
+
+	if (likely(dest_pp_int.s.intr)) {
+		irq_hw_number_t intsn = dest_pp_int.s.intsn;
+		int mbox = intsn - octeon_irq_ciu3_base_mbox_intsn(core);
+
+		if (likely(mbox >= 0 && mbox < CIU3_MBOX_PER_CORE)) {
+			do_IRQ(mbox + OCTEON_IRQ_MBOX0);
+		} else {
+			union cvmx_ciu3_iscx_w1c isc_w1c;
+			u64 isc_w1c_addr = ciu3_addr + CIU3_ISC_W1C(intsn);
+
+			isc_w1c.u64 = 0;
+			isc_w1c.s.en = 1;
+			cvmx_write_csr(isc_w1c_addr, isc_w1c.u64);
+			cvmx_read_csr(isc_w1c_addr);
+			spurious_interrupt();
+		}
+	} else {
+		spurious_interrupt();
+	}
+}
+
+void octeon_ciu3_mbox_send(int cpu, unsigned int mbox)
+{
+	struct octeon_ciu3_info *ciu3_info;
+	unsigned int intsn;
+	union cvmx_ciu3_iscx_w1s isc_w1s;
+	u64 isc_w1s_addr;
+
+	if (WARN_ON_ONCE(mbox >= CIU3_MBOX_PER_CORE))
+		return;
+
+	intsn = octeon_irq_ciu3_mbox_intsn_for_cpu(cpu, mbox);
+	ciu3_info = per_cpu(octeon_ciu3_info, cpu);
+	isc_w1s_addr = ciu3_info->ciu3_addr + CIU3_ISC_W1S(intsn);
+
+	isc_w1s.u64 = 0;
+	isc_w1s.s.raw = 1;
+
+	cvmx_write_csr(isc_w1s_addr, isc_w1s.u64);
+	cvmx_read_csr(isc_w1s_addr);
+}
+
+static void octeon_irq_ciu3_mbox_set_enable(struct irq_data *data, int cpu, bool en)
+{
+	struct octeon_ciu3_info *ciu3_info;
+	unsigned int intsn;
+	u64 isc_ctl_addr, isc_w1c_addr;
+	union cvmx_ciu3_iscx_ctl isc_ctl;
+	unsigned int mbox = data->irq - OCTEON_IRQ_MBOX0;
+
+	intsn = octeon_irq_ciu3_mbox_intsn_for_cpu(cpu, mbox);
+	ciu3_info = per_cpu(octeon_ciu3_info, cpu);
+	isc_w1c_addr = ciu3_info->ciu3_addr + CIU3_ISC_W1C(intsn);
+	isc_ctl_addr = ciu3_info->ciu3_addr + CIU3_ISC_CTL(intsn);
+
+	isc_ctl.u64 = 0;
+	isc_ctl.s.en = 1;
+
+	cvmx_write_csr(isc_w1c_addr, isc_ctl.u64);
+	cvmx_write_csr(isc_ctl_addr, 0);
+	if (en) {
+		unsigned int idt = per_cpu(octeon_irq_ciu3_idt_ip3, cpu);
+
+		isc_ctl.u64 = 0;
+		isc_ctl.s.en = 1;
+		isc_ctl.s.idt = idt;
+		cvmx_write_csr(isc_ctl_addr, isc_ctl.u64);
+	}
+	cvmx_read_csr(isc_ctl_addr);
+}
+
+static void octeon_irq_ciu3_mbox_enable(struct irq_data *data)
+{
+	int cpu;
+	unsigned int mbox = data->irq - OCTEON_IRQ_MBOX0;
+
+	WARN_ON(mbox >= CIU3_MBOX_PER_CORE);
+
+	for_each_online_cpu(cpu)
+		octeon_irq_ciu3_mbox_set_enable(data, cpu, true);
+}
+
+static void octeon_irq_ciu3_mbox_disable(struct irq_data *data)
+{
+	int cpu;
+	unsigned int mbox = data->irq - OCTEON_IRQ_MBOX0;
+
+	WARN_ON(mbox >= CIU3_MBOX_PER_CORE);
+
+	for_each_online_cpu(cpu)
+		octeon_irq_ciu3_mbox_set_enable(data, cpu, false);
+}
+
+static void octeon_irq_ciu3_mbox_ack(struct irq_data *data)
+{
+	struct octeon_ciu3_info *ciu3_info;
+	unsigned int intsn;
+	u64 isc_w1c_addr;
+	union cvmx_ciu3_iscx_w1c isc_w1c;
+	unsigned int mbox = data->irq - OCTEON_IRQ_MBOX0;
+
+	intsn = octeon_irq_ciu3_mbox_intsn_for_core(cvmx_get_local_core_num(), mbox);
+
+	isc_w1c.u64 = 0;
+	isc_w1c.s.raw = 1;
+
+	ciu3_info = __this_cpu_read(octeon_ciu3_info);
+	isc_w1c_addr = ciu3_info->ciu3_addr + CIU3_ISC_W1C(intsn);
+	cvmx_write_csr(isc_w1c_addr, isc_w1c.u64);
+	cvmx_read_csr(isc_w1c_addr);
+}
+
+static void octeon_irq_ciu3_mbox_cpu_online(struct irq_data *data)
+{
+	octeon_irq_ciu3_mbox_set_enable(data, smp_processor_id(), true);
+}
+
+static void octeon_irq_ciu3_mbox_cpu_offline(struct irq_data *data)
+{
+	octeon_irq_ciu3_mbox_set_enable(data, smp_processor_id(), false);
+}
+
+static int octeon_irq_ciu3_alloc_resources(struct octeon_ciu3_info *ciu3_info)
+{
+	u64 b = ciu3_info->ciu3_addr;
+	int idt_ip2, idt_ip3, idt_ip4;
+	int unused_idt2;
+	int core = cvmx_get_local_core_num();
+	int i;
+
+	__this_cpu_write(octeon_ciu3_info, ciu3_info);
+
+	/*
+	 * 4 idt per core starting from 1 because zero is reserved.
+	 * Base idt per core is 4 * core + 1
+	 */
+	idt_ip2 = core * 4 + 1;
+	idt_ip3 = core * 4 + 2;
+	idt_ip4 = core * 4 + 3;
+	unused_idt2 = core * 4 + 4;
+	__this_cpu_write(octeon_irq_ciu3_idt_ip2, idt_ip2);
+	__this_cpu_write(octeon_irq_ciu3_idt_ip3, idt_ip3);
+
+	/* ip2 interrupts for this CPU */
+	cvmx_write_csr(b + CIU3_IDT_CTL(idt_ip2), 0);
+	cvmx_write_csr(b + CIU3_IDT_PP(idt_ip2, 0), 1ull << core);
+	cvmx_write_csr(b + CIU3_IDT_IO(idt_ip2), 0);
+
+	/* ip3 interrupts for this CPU */
+	cvmx_write_csr(b + CIU3_IDT_CTL(idt_ip3), 1);
+	cvmx_write_csr(b + CIU3_IDT_PP(idt_ip3, 0), 1ull << core);
+	cvmx_write_csr(b + CIU3_IDT_IO(idt_ip3), 0);
+
+	/* ip4 interrupts for this CPU */
+	cvmx_write_csr(b + CIU3_IDT_CTL(idt_ip4), 2);
+	cvmx_write_csr(b + CIU3_IDT_PP(idt_ip4, 0), 0);
+	cvmx_write_csr(b + CIU3_IDT_IO(idt_ip4), 0);
+
+	cvmx_write_csr(b + CIU3_IDT_CTL(unused_idt2), 0);
+	cvmx_write_csr(b + CIU3_IDT_PP(unused_idt2, 0), 0);
+	cvmx_write_csr(b + CIU3_IDT_IO(unused_idt2), 0);
+
+	for (i = 0; i < CIU3_MBOX_PER_CORE; i++) {
+		unsigned int intsn = octeon_irq_ciu3_mbox_intsn_for_core(core, i);
+
+		cvmx_write_csr(b + CIU3_ISC_W1C(intsn), 2);
+		cvmx_write_csr(b + CIU3_ISC_CTL(intsn), 0);
+	}
+
+	return 0;
+}
+
+static void octeon_irq_setup_secondary_ciu3(void)
+{
+	struct octeon_ciu3_info *ciu3_info;
+
+	ciu3_info = octeon_ciu3_info_per_node[cvmx_get_node_num()];
+	octeon_irq_ciu3_alloc_resources(ciu3_info);
+	irq_cpu_online();
+
+	/* Enable the CIU lines */
+	set_c0_status(STATUSF_IP3 | STATUSF_IP2);
+	if (octeon_irq_use_ip4)
+		set_c0_status(STATUSF_IP4);
+	else
+		clear_c0_status(STATUSF_IP4);
+}
+
+static struct irq_chip octeon_irq_chip_ciu3_mbox = {
+	.name = "CIU3-M",
+	.irq_enable = octeon_irq_ciu3_mbox_enable,
+	.irq_disable = octeon_irq_ciu3_mbox_disable,
+	.irq_ack = octeon_irq_ciu3_mbox_ack,
+
+	.irq_cpu_online = octeon_irq_ciu3_mbox_cpu_online,
+	.irq_cpu_offline = octeon_irq_ciu3_mbox_cpu_offline,
+	.flags = IRQCHIP_ONOFFLINE_ENABLED,
+};
+
+static int __init octeon_irq_init_ciu3(struct device_node *ciu_node,
+				       struct device_node *parent)
+{
+	int i;
+	int node;
+	struct irq_domain *domain;
+	struct octeon_ciu3_info *ciu3_info;
+	const __be32 *zero_addr;
+	u64 base_addr;
+	union cvmx_ciu3_const consts;
+
+	node = 0; /* of_node_to_nid(ciu_node); */
+	ciu3_info = kzalloc_node(sizeof(*ciu3_info), GFP_KERNEL, node);
+
+	if (!ciu3_info)
+		return -ENOMEM;
+
+	zero_addr = of_get_address(ciu_node, 0, NULL, NULL);
+	if (WARN_ON(!zero_addr))
+		return -EINVAL;
+
+	base_addr = of_translate_address(ciu_node, zero_addr);
+	base_addr = (u64)phys_to_virt(base_addr);
+
+	ciu3_info->ciu3_addr = base_addr;
+	ciu3_info->node = node;
+
+	consts.u64 = cvmx_read_csr(base_addr + CIU3_CONST);
+
+	octeon_irq_setup_secondary = octeon_irq_setup_secondary_ciu3;
+
+	octeon_irq_ip2 = octeon_irq_ciu3_ip2;
+	octeon_irq_ip3 = octeon_irq_ciu3_mbox;
+	octeon_irq_ip4 = octeon_irq_ip4_mask;
+
+	if (node == cvmx_get_node_num()) {
+		/* Mips internal */
+		octeon_irq_init_core();
+
+		/* Only do per CPU things if it is the CIU of the boot node. */
+		i = irq_alloc_descs_from(OCTEON_IRQ_MBOX0, 8, node);
+		WARN_ON(i < 0);
+
+		for (i = 0; i < 8; i++)
+			irq_set_chip_and_handler(i + OCTEON_IRQ_MBOX0,
+						 &octeon_irq_chip_ciu3_mbox, handle_percpu_irq);
+	}
+
+	/*
+	 * Initialize all domains to use the default domain. Specific major
+	 * blocks will overwrite the default domain as needed.
+	 */
+	domain = irq_domain_add_tree(ciu_node, &octeon_dflt_domain_ciu3_ops,
+				     ciu3_info);
+	for (i = 0; i < MAX_CIU3_DOMAINS; i++)
+		ciu3_info->domain[i] = domain;
+
+	octeon_ciu3_info_per_node[node] = ciu3_info;
+
+	if (node == cvmx_get_node_num()) {
+		/* Only do per CPU things if it is the CIU of the boot node. */
+		octeon_irq_ciu3_alloc_resources(ciu3_info);
+		if (node == 0)
+			irq_set_default_host(domain);
+
+		octeon_irq_use_ip4 = false;
+		/* Enable the CIU lines */
+		set_c0_status(STATUSF_IP2 | STATUSF_IP3);
+		clear_c0_status(STATUSF_IP4);
+	}
+
+	return 0;
+}
+
+static struct of_device_id ciu_types[] __initdata = {
+	{.compatible = "cavium,octeon-3860-ciu", .data = octeon_irq_init_ciu},
+	{.compatible = "cavium,octeon-3860-gpio", .data = octeon_irq_init_gpio},
+	{.compatible = "cavium,octeon-6880-ciu2", .data = octeon_irq_init_ciu2},
+	{.compatible = "cavium,octeon-7890-ciu3", .data = octeon_irq_init_ciu3},
+	{.compatible = "cavium,octeon-7130-cib", .data = octeon_irq_init_cib},
+	{}
+};
+
+void __init arch_init_irq(void)
+{
+#ifdef CONFIG_SMP
+	/* Set the default affinity to the boot cpu. */
+	cpumask_clear(irq_default_affinity);
+	cpumask_set_cpu(smp_processor_id(), irq_default_affinity);
+#endif
+	of_irq_init(ciu_types);
+}
+
+asmlinkage void plat_irq_dispatch(void)
+{
+	unsigned long cop0_cause;
+	unsigned long cop0_status;
+
+	while (1) {
+		cop0_cause = read_c0_cause();
+		cop0_status = read_c0_status();
+		cop0_cause &= cop0_status;
+		cop0_cause &= ST0_IM;
+
+		if (cop0_cause & STATUSF_IP2)
+			octeon_irq_ip2();
+		else if (cop0_cause & STATUSF_IP3)
+			octeon_irq_ip3();
+		else if (cop0_cause & STATUSF_IP4)
+			octeon_irq_ip4();
+		else if (cop0_cause)
+			do_IRQ(fls(cop0_cause) - 9 + MIPS_CPU_IRQ_BASE);
+		else
+			break;
+	}
+}
+
+#ifdef CONFIG_HOTPLUG_CPU
+
+void octeon_fixup_irqs(void)
+{
+	irq_cpu_offline();
+}
+
+#endif /* CONFIG_HOTPLUG_CPU */
+
+struct irq_domain *octeon_irq_get_block_domain(int node, uint8_t block)
+{
+	struct octeon_ciu3_info *ciu3_info;
+
+	ciu3_info = octeon_ciu3_info_per_node[node & CVMX_NODE_MASK];
+	return ciu3_info->domain[block];
+}
+EXPORT_SYMBOL(octeon_irq_get_block_domain);
diff --git a/arch/mips/cavium-octeon/octeon-memcpy.S b/arch/mips/cavium-octeon/octeon-memcpy.S
new file mode 100644
index 000000000..25860fba6
--- /dev/null
+++ b/arch/mips/cavium-octeon/octeon-memcpy.S
@@ -0,0 +1,484 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Unified implementation of memcpy, memmove and the __copy_user backend.
+ *
+ * Copyright (C) 1998, 99, 2000, 01, 2002 Ralf Baechle (ralf@gnu.org)
+ * Copyright (C) 1999, 2000, 01, 2002 Silicon Graphics, Inc.
+ * Copyright (C) 2002 Broadcom, Inc.
+ *   memcpy/copy_user author: Mark Vandevoorde
+ *
+ * Mnemonic names for arguments to memcpy/__copy_user
+ */
+
+#include <asm/asm.h>
+#include <asm/asm-offsets.h>
+#include <asm/export.h>
+#include <asm/regdef.h>
+
+#define dst a0
+#define src a1
+#define len a2
+
+/*
+ * Spec
+ *
+ * memcpy copies len bytes from src to dst and sets v0 to dst.
+ * It assumes that
+ *   - src and dst don't overlap
+ *   - src is readable
+ *   - dst is writable
+ * memcpy uses the standard calling convention
+ *
+ * __copy_user copies up to len bytes from src to dst and sets a2 (len) to
+ * the number of uncopied bytes due to an exception caused by a read or write.
+ * __copy_user assumes that src and dst don't overlap, and that the call is
+ * implementing one of the following:
+ *   copy_to_user
+ *     - src is readable  (no exceptions when reading src)
+ *   copy_from_user
+ *     - dst is writable  (no exceptions when writing dst)
+ * __copy_user uses a non-standard calling convention; see
+ * arch/mips/include/asm/uaccess.h
+ *
+ * When an exception happens on a load, the handler must
+ # ensure that all of the destination buffer is overwritten to prevent
+ * leaking information to user mode programs.
+ */
+
+/*
+ * Implementation
+ */
+
+/*
+ * The exception handler for loads requires that:
+ *  1- AT contain the address of the byte just past the end of the source
+ *     of the copy,
+ *  2- src_entry <= src < AT, and
+ *  3- (dst - src) == (dst_entry - src_entry),
+ * The _entry suffix denotes values when __copy_user was called.
+ *
+ * (1) is set up up by uaccess.h and maintained by not writing AT in copy_user
+ * (2) is met by incrementing src by the number of bytes copied
+ * (3) is met by not doing loads between a pair of increments of dst and src
+ *
+ * The exception handlers for stores adjust len (if necessary) and return.
+ * These handlers do not need to overwrite any data.
+ *
+ * For __rmemcpy and memmove an exception is always a kernel bug, therefore
+ * they're not protected.
+ */
+
+#define EXC(inst_reg,addr,handler)		\
+9:	inst_reg, addr;				\
+	.section __ex_table,"a";		\
+	PTR_WD	9b, handler;			\
+	.previous
+
+/*
+ * Only on the 64-bit kernel we can made use of 64-bit registers.
+ */
+
+#define LOAD   ld
+#define LOADL  ldl
+#define LOADR  ldr
+#define STOREL sdl
+#define STORER sdr
+#define STORE  sd
+#define ADD    daddu
+#define SUB    dsubu
+#define SRL    dsrl
+#define SRA    dsra
+#define SLL    dsll
+#define SLLV   dsllv
+#define SRLV   dsrlv
+#define NBYTES 8
+#define LOG_NBYTES 3
+
+/*
+ * As we are sharing code base with the mips32 tree (which use the o32 ABI
+ * register definitions). We need to redefine the register definitions from
+ * the n64 ABI register naming to the o32 ABI register naming.
+ */
+#undef t0
+#undef t1
+#undef t2
+#undef t3
+#define t0	$8
+#define t1	$9
+#define t2	$10
+#define t3	$11
+#define t4	$12
+#define t5	$13
+#define t6	$14
+#define t7	$15
+
+#ifdef CONFIG_CPU_LITTLE_ENDIAN
+#define LDFIRST LOADR
+#define LDREST	LOADL
+#define STFIRST STORER
+#define STREST	STOREL
+#define SHIFT_DISCARD SLLV
+#else
+#define LDFIRST LOADL
+#define LDREST	LOADR
+#define STFIRST STOREL
+#define STREST	STORER
+#define SHIFT_DISCARD SRLV
+#endif
+
+#define FIRST(unit) ((unit)*NBYTES)
+#define REST(unit)  (FIRST(unit)+NBYTES-1)
+#define UNIT(unit)  FIRST(unit)
+
+#define ADDRMASK (NBYTES-1)
+
+	.text
+	.set	noreorder
+	.set	noat
+
+/*
+ * A combined memcpy/__copy_user
+ * __copy_user sets len to 0 for success; else to an upper bound of
+ * the number of uncopied bytes.
+ * memcpy sets v0 to dst.
+ */
+	.align	5
+LEAF(memcpy)					/* a0=dst a1=src a2=len */
+EXPORT_SYMBOL(memcpy)
+	move	v0, dst				/* return value */
+__memcpy:
+FEXPORT(__raw_copy_from_user)
+EXPORT_SYMBOL(__raw_copy_from_user)
+FEXPORT(__raw_copy_to_user)
+EXPORT_SYMBOL(__raw_copy_to_user)
+	/*
+	 * Note: dst & src may be unaligned, len may be 0
+	 * Temps
+	 */
+	#
+	# Octeon doesn't care if the destination is unaligned. The hardware
+	# can fix it faster than we can special case the assembly.
+	#
+	pref	0, 0(src)
+	sltu	t0, len, NBYTES		# Check if < 1 word
+	bnez	t0, copy_bytes_checklen
+	 and	t0, src, ADDRMASK	# Check if src unaligned
+	bnez	t0, src_unaligned
+	 sltu	t0, len, 4*NBYTES	# Check if < 4 words
+	bnez	t0, less_than_4units
+	 sltu	t0, len, 8*NBYTES	# Check if < 8 words
+	bnez	t0, less_than_8units
+	 sltu	t0, len, 16*NBYTES	# Check if < 16 words
+	bnez	t0, cleanup_both_aligned
+	 sltu	t0, len, 128+1		# Check if len < 129
+	bnez	t0, 1f			# Skip prefetch if len is too short
+	 sltu	t0, len, 256+1		# Check if len < 257
+	bnez	t0, 1f			# Skip prefetch if len is too short
+	 pref	0, 128(src)		# We must not prefetch invalid addresses
+	#
+	# This is where we loop if there is more than 128 bytes left
+2:	pref	0, 256(src)		# We must not prefetch invalid addresses
+	#
+	# This is where we loop if we can't prefetch anymore
+1:
+EXC(	LOAD	t0, UNIT(0)(src),	l_exc)
+EXC(	LOAD	t1, UNIT(1)(src),	l_exc_copy)
+EXC(	LOAD	t2, UNIT(2)(src),	l_exc_copy)
+EXC(	LOAD	t3, UNIT(3)(src),	l_exc_copy)
+	SUB	len, len, 16*NBYTES
+EXC(	STORE	t0, UNIT(0)(dst),	s_exc_p16u)
+EXC(	STORE	t1, UNIT(1)(dst),	s_exc_p15u)
+EXC(	STORE	t2, UNIT(2)(dst),	s_exc_p14u)
+EXC(	STORE	t3, UNIT(3)(dst),	s_exc_p13u)
+EXC(	LOAD	t0, UNIT(4)(src),	l_exc_copy)
+EXC(	LOAD	t1, UNIT(5)(src),	l_exc_copy)
+EXC(	LOAD	t2, UNIT(6)(src),	l_exc_copy)
+EXC(	LOAD	t3, UNIT(7)(src),	l_exc_copy)
+EXC(	STORE	t0, UNIT(4)(dst),	s_exc_p12u)
+EXC(	STORE	t1, UNIT(5)(dst),	s_exc_p11u)
+EXC(	STORE	t2, UNIT(6)(dst),	s_exc_p10u)
+	ADD	src, src, 16*NBYTES
+EXC(	STORE	t3, UNIT(7)(dst),	s_exc_p9u)
+	ADD	dst, dst, 16*NBYTES
+EXC(	LOAD	t0, UNIT(-8)(src),	l_exc_copy_rewind16)
+EXC(	LOAD	t1, UNIT(-7)(src),	l_exc_copy_rewind16)
+EXC(	LOAD	t2, UNIT(-6)(src),	l_exc_copy_rewind16)
+EXC(	LOAD	t3, UNIT(-5)(src),	l_exc_copy_rewind16)
+EXC(	STORE	t0, UNIT(-8)(dst),	s_exc_p8u)
+EXC(	STORE	t1, UNIT(-7)(dst),	s_exc_p7u)
+EXC(	STORE	t2, UNIT(-6)(dst),	s_exc_p6u)
+EXC(	STORE	t3, UNIT(-5)(dst),	s_exc_p5u)
+EXC(	LOAD	t0, UNIT(-4)(src),	l_exc_copy_rewind16)
+EXC(	LOAD	t1, UNIT(-3)(src),	l_exc_copy_rewind16)
+EXC(	LOAD	t2, UNIT(-2)(src),	l_exc_copy_rewind16)
+EXC(	LOAD	t3, UNIT(-1)(src),	l_exc_copy_rewind16)
+EXC(	STORE	t0, UNIT(-4)(dst),	s_exc_p4u)
+EXC(	STORE	t1, UNIT(-3)(dst),	s_exc_p3u)
+EXC(	STORE	t2, UNIT(-2)(dst),	s_exc_p2u)
+EXC(	STORE	t3, UNIT(-1)(dst),	s_exc_p1u)
+	sltu	t0, len, 256+1		# See if we can prefetch more
+	beqz	t0, 2b
+	 sltu	t0, len, 128		# See if we can loop more time
+	beqz	t0, 1b
+	 nop
+	#
+	# Jump here if there are less than 16*NBYTES left.
+	#
+cleanup_both_aligned:
+	beqz	len, done
+	 sltu	t0, len, 8*NBYTES
+	bnez	t0, less_than_8units
+	 nop
+EXC(	LOAD	t0, UNIT(0)(src),	l_exc)
+EXC(	LOAD	t1, UNIT(1)(src),	l_exc_copy)
+EXC(	LOAD	t2, UNIT(2)(src),	l_exc_copy)
+EXC(	LOAD	t3, UNIT(3)(src),	l_exc_copy)
+	SUB	len, len, 8*NBYTES
+EXC(	STORE	t0, UNIT(0)(dst),	s_exc_p8u)
+EXC(	STORE	t1, UNIT(1)(dst),	s_exc_p7u)
+EXC(	STORE	t2, UNIT(2)(dst),	s_exc_p6u)
+EXC(	STORE	t3, UNIT(3)(dst),	s_exc_p5u)
+EXC(	LOAD	t0, UNIT(4)(src),	l_exc_copy)
+EXC(	LOAD	t1, UNIT(5)(src),	l_exc_copy)
+EXC(	LOAD	t2, UNIT(6)(src),	l_exc_copy)
+EXC(	LOAD	t3, UNIT(7)(src),	l_exc_copy)
+EXC(	STORE	t0, UNIT(4)(dst),	s_exc_p4u)
+EXC(	STORE	t1, UNIT(5)(dst),	s_exc_p3u)
+EXC(	STORE	t2, UNIT(6)(dst),	s_exc_p2u)
+EXC(	STORE	t3, UNIT(7)(dst),	s_exc_p1u)
+	ADD	src, src, 8*NBYTES
+	beqz	len, done
+	 ADD	dst, dst, 8*NBYTES
+	#
+	# Jump here if there are less than 8*NBYTES left.
+	#
+less_than_8units:
+	sltu	t0, len, 4*NBYTES
+	bnez	t0, less_than_4units
+	 nop
+EXC(	LOAD	t0, UNIT(0)(src),	l_exc)
+EXC(	LOAD	t1, UNIT(1)(src),	l_exc_copy)
+EXC(	LOAD	t2, UNIT(2)(src),	l_exc_copy)
+EXC(	LOAD	t3, UNIT(3)(src),	l_exc_copy)
+	SUB	len, len, 4*NBYTES
+EXC(	STORE	t0, UNIT(0)(dst),	s_exc_p4u)
+EXC(	STORE	t1, UNIT(1)(dst),	s_exc_p3u)
+EXC(	STORE	t2, UNIT(2)(dst),	s_exc_p2u)
+EXC(	STORE	t3, UNIT(3)(dst),	s_exc_p1u)
+	ADD	src, src, 4*NBYTES
+	beqz	len, done
+	 ADD	dst, dst, 4*NBYTES
+	#
+	# Jump here if there are less than 4*NBYTES left. This means
+	# we may need to copy up to 3 NBYTES words.
+	#
+less_than_4units:
+	sltu	t0, len, 1*NBYTES
+	bnez	t0, copy_bytes_checklen
+	 nop
+	#
+	# 1) Copy NBYTES, then check length again
+	#
+EXC(	LOAD	t0, 0(src),		l_exc)
+	SUB	len, len, NBYTES
+	sltu	t1, len, 8
+EXC(	STORE	t0, 0(dst),		s_exc_p1u)
+	ADD	src, src, NBYTES
+	bnez	t1, copy_bytes_checklen
+	 ADD	dst, dst, NBYTES
+	#
+	# 2) Copy NBYTES, then check length again
+	#
+EXC(	LOAD	t0, 0(src),		l_exc)
+	SUB	len, len, NBYTES
+	sltu	t1, len, 8
+EXC(	STORE	t0, 0(dst),		s_exc_p1u)
+	ADD	src, src, NBYTES
+	bnez	t1, copy_bytes_checklen
+	 ADD	dst, dst, NBYTES
+	#
+	# 3) Copy NBYTES, then check length again
+	#
+EXC(	LOAD	t0, 0(src),		l_exc)
+	SUB	len, len, NBYTES
+	ADD	src, src, NBYTES
+	ADD	dst, dst, NBYTES
+	b copy_bytes_checklen
+EXC(	 STORE	t0, -8(dst),		s_exc_p1u)
+
+src_unaligned:
+#define rem t8
+	SRL	t0, len, LOG_NBYTES+2	 # +2 for 4 units/iter
+	beqz	t0, cleanup_src_unaligned
+	 and	rem, len, (4*NBYTES-1)	 # rem = len % 4*NBYTES
+1:
+/*
+ * Avoid consecutive LD*'s to the same register since some mips
+ * implementations can't issue them in the same cycle.
+ * It's OK to load FIRST(N+1) before REST(N) because the two addresses
+ * are to the same unit (unless src is aligned, but it's not).
+ */
+EXC(	LDFIRST t0, FIRST(0)(src),	l_exc)
+EXC(	LDFIRST t1, FIRST(1)(src),	l_exc_copy)
+	SUB	len, len, 4*NBYTES
+EXC(	LDREST	t0, REST(0)(src),	l_exc_copy)
+EXC(	LDREST	t1, REST(1)(src),	l_exc_copy)
+EXC(	LDFIRST t2, FIRST(2)(src),	l_exc_copy)
+EXC(	LDFIRST t3, FIRST(3)(src),	l_exc_copy)
+EXC(	LDREST	t2, REST(2)(src),	l_exc_copy)
+EXC(	LDREST	t3, REST(3)(src),	l_exc_copy)
+	ADD	src, src, 4*NBYTES
+EXC(	STORE	t0, UNIT(0)(dst),	s_exc_p4u)
+EXC(	STORE	t1, UNIT(1)(dst),	s_exc_p3u)
+EXC(	STORE	t2, UNIT(2)(dst),	s_exc_p2u)
+EXC(	STORE	t3, UNIT(3)(dst),	s_exc_p1u)
+	bne	len, rem, 1b
+	 ADD	dst, dst, 4*NBYTES
+
+cleanup_src_unaligned:
+	beqz	len, done
+	 and	rem, len, NBYTES-1  # rem = len % NBYTES
+	beq	rem, len, copy_bytes
+	 nop
+1:
+EXC(	LDFIRST t0, FIRST(0)(src),	l_exc)
+EXC(	LDREST	t0, REST(0)(src),	l_exc_copy)
+	SUB	len, len, NBYTES
+EXC(	STORE	t0, 0(dst),		s_exc_p1u)
+	ADD	src, src, NBYTES
+	bne	len, rem, 1b
+	 ADD	dst, dst, NBYTES
+
+copy_bytes_checklen:
+	beqz	len, done
+	 nop
+copy_bytes:
+	/* 0 < len < NBYTES  */
+#define COPY_BYTE(N)			\
+EXC(	lb	t0, N(src), l_exc);	\
+	SUB	len, len, 1;		\
+	beqz	len, done;		\
+EXC(	 sb	t0, N(dst), s_exc_p1)
+
+	COPY_BYTE(0)
+	COPY_BYTE(1)
+	COPY_BYTE(2)
+	COPY_BYTE(3)
+	COPY_BYTE(4)
+	COPY_BYTE(5)
+EXC(	lb	t0, NBYTES-2(src), l_exc)
+	SUB	len, len, 1
+	jr	ra
+EXC(	 sb	t0, NBYTES-2(dst), s_exc_p1)
+done:
+	jr	ra
+	 nop
+	END(memcpy)
+
+l_exc_copy_rewind16:
+	/* Rewind src and dst by 16*NBYTES for l_exc_copy */
+	SUB	src, src, 16*NBYTES
+	SUB	dst, dst, 16*NBYTES
+l_exc_copy:
+	/*
+	 * Copy bytes from src until faulting load address (or until a
+	 * lb faults)
+	 *
+	 * When reached by a faulting LDFIRST/LDREST, THREAD_BUADDR($28)
+	 * may be more than a byte beyond the last address.
+	 * Hence, the lb below may get an exception.
+	 *
+	 * Assumes src < THREAD_BUADDR($28)
+	 */
+	LOAD	t0, TI_TASK($28)
+	LOAD	t0, THREAD_BUADDR(t0)
+1:
+EXC(	lb	t1, 0(src),	l_exc)
+	ADD	src, src, 1
+	sb	t1, 0(dst)	# can't fault -- we're copy_from_user
+	bne	src, t0, 1b
+	 ADD	dst, dst, 1
+l_exc:
+	LOAD	t0, TI_TASK($28)
+	LOAD	t0, THREAD_BUADDR(t0)	# t0 is just past last good address
+	SUB	len, AT, t0		# len number of uncopied bytes
+	jr	ra
+	 nop
+
+
+#define SEXC(n)				\
+s_exc_p ## n ## u:			\
+	jr	ra;			\
+	 ADD	len, len, n*NBYTES
+
+SEXC(16)
+SEXC(15)
+SEXC(14)
+SEXC(13)
+SEXC(12)
+SEXC(11)
+SEXC(10)
+SEXC(9)
+SEXC(8)
+SEXC(7)
+SEXC(6)
+SEXC(5)
+SEXC(4)
+SEXC(3)
+SEXC(2)
+SEXC(1)
+
+s_exc_p1:
+	jr	ra
+	 ADD	len, len, 1
+s_exc:
+	jr	ra
+	 nop
+
+	.align	5
+LEAF(memmove)
+EXPORT_SYMBOL(memmove)
+	ADD	t0, a0, a2
+	ADD	t1, a1, a2
+	sltu	t0, a1, t0			# dst + len <= src -> memcpy
+	sltu	t1, a0, t1			# dst >= src + len -> memcpy
+	and	t0, t1
+	beqz	t0, __memcpy
+	 move	v0, a0				/* return value */
+	beqz	a2, r_out
+	END(memmove)
+
+	/* fall through to __rmemcpy */
+LEAF(__rmemcpy)					/* a0=dst a1=src a2=len */
+	 sltu	t0, a1, a0
+	beqz	t0, r_end_bytes_up		# src >= dst
+	 nop
+	ADD	a0, a2				# dst = dst + len
+	ADD	a1, a2				# src = src + len
+
+r_end_bytes:
+	lb	t0, -1(a1)
+	SUB	a2, a2, 0x1
+	sb	t0, -1(a0)
+	SUB	a1, a1, 0x1
+	bnez	a2, r_end_bytes
+	 SUB	a0, a0, 0x1
+
+r_out:
+	jr	ra
+	 move	a2, zero
+
+r_end_bytes_up:
+	lb	t0, (a1)
+	SUB	a2, a2, 0x1
+	sb	t0, (a0)
+	ADD	a1, a1, 0x1
+	bnez	a2, r_end_bytes_up
+	 ADD	a0, a0, 0x1
+
+	jr	ra
+	 move	a2, zero
+	END(__rmemcpy)
diff --git a/arch/mips/cavium-octeon/octeon-platform.c b/arch/mips/cavium-octeon/octeon-platform.c
new file mode 100644
index 000000000..ce05c0dd3
--- /dev/null
+++ b/arch/mips/cavium-octeon/octeon-platform.c
@@ -0,0 +1,1141 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2004-2017 Cavium, Inc.
+ * Copyright (C) 2008 Wind River Systems
+ */
+
+#include <linux/etherdevice.h>
+#include <linux/of_platform.h>
+#include <linux/of_fdt.h>
+#include <linux/libfdt.h>
+
+#include <asm/octeon/octeon.h>
+#include <asm/octeon/cvmx-helper-board.h>
+
+#ifdef CONFIG_USB
+#include <linux/usb/ehci_def.h>
+#include <linux/usb/ehci_pdriver.h>
+#include <linux/usb/ohci_pdriver.h>
+#include <asm/octeon/cvmx-uctlx-defs.h>
+
+#define CVMX_UAHCX_EHCI_USBCMD	(CVMX_ADD_IO_SEG(0x00016F0000000010ull))
+#define CVMX_UAHCX_OHCI_USBCMD	(CVMX_ADD_IO_SEG(0x00016F0000000408ull))
+
+static DEFINE_MUTEX(octeon2_usb_clocks_mutex);
+
+static int octeon2_usb_clock_start_cnt;
+
+static int __init octeon2_usb_reset(void)
+{
+	union cvmx_uctlx_clk_rst_ctl clk_rst_ctl;
+	u32 ucmd;
+
+	if (!OCTEON_IS_OCTEON2())
+		return 0;
+
+	clk_rst_ctl.u64 = cvmx_read_csr(CVMX_UCTLX_CLK_RST_CTL(0));
+	if (clk_rst_ctl.s.hrst) {
+		ucmd = cvmx_read64_uint32(CVMX_UAHCX_EHCI_USBCMD);
+		ucmd &= ~CMD_RUN;
+		cvmx_write64_uint32(CVMX_UAHCX_EHCI_USBCMD, ucmd);
+		mdelay(2);
+		ucmd |= CMD_RESET;
+		cvmx_write64_uint32(CVMX_UAHCX_EHCI_USBCMD, ucmd);
+		ucmd = cvmx_read64_uint32(CVMX_UAHCX_OHCI_USBCMD);
+		ucmd |= CMD_RUN;
+		cvmx_write64_uint32(CVMX_UAHCX_OHCI_USBCMD, ucmd);
+	}
+
+	return 0;
+}
+arch_initcall(octeon2_usb_reset);
+
+static void octeon2_usb_clocks_start(struct device *dev)
+{
+	u64 div;
+	union cvmx_uctlx_if_ena if_ena;
+	union cvmx_uctlx_clk_rst_ctl clk_rst_ctl;
+	union cvmx_uctlx_uphy_portx_ctl_status port_ctl_status;
+	int i;
+	unsigned long io_clk_64_to_ns;
+	u32 clock_rate = 12000000;
+	bool is_crystal_clock = false;
+
+
+	mutex_lock(&octeon2_usb_clocks_mutex);
+
+	octeon2_usb_clock_start_cnt++;
+	if (octeon2_usb_clock_start_cnt != 1)
+		goto exit;
+
+	io_clk_64_to_ns = 64000000000ull / octeon_get_io_clock_rate();
+
+	if (dev->of_node) {
+		struct device_node *uctl_node;
+		const char *clock_type;
+
+		uctl_node = of_get_parent(dev->of_node);
+		if (!uctl_node) {
+			dev_err(dev, "No UCTL device node\n");
+			goto exit;
+		}
+		i = of_property_read_u32(uctl_node,
+					 "refclk-frequency", &clock_rate);
+		if (i) {
+			dev_err(dev, "No UCTL \"refclk-frequency\"\n");
+			of_node_put(uctl_node);
+			goto exit;
+		}
+		i = of_property_read_string(uctl_node,
+					    "refclk-type", &clock_type);
+		of_node_put(uctl_node);
+		if (!i && strcmp("crystal", clock_type) == 0)
+			is_crystal_clock = true;
+	}
+
+	/*
+	 * Step 1: Wait for voltages stable.  That surely happened
+	 * before starting the kernel.
+	 *
+	 * Step 2: Enable  SCLK of UCTL by writing UCTL0_IF_ENA[EN] = 1
+	 */
+	if_ena.u64 = 0;
+	if_ena.s.en = 1;
+	cvmx_write_csr(CVMX_UCTLX_IF_ENA(0), if_ena.u64);
+
+	for (i = 0; i <= 1; i++) {
+		port_ctl_status.u64 =
+			cvmx_read_csr(CVMX_UCTLX_UPHY_PORTX_CTL_STATUS(i, 0));
+		/* Set txvreftune to 15 to obtain compliant 'eye' diagram. */
+		port_ctl_status.s.txvreftune = 15;
+		port_ctl_status.s.txrisetune = 1;
+		port_ctl_status.s.txpreemphasistune = 1;
+		cvmx_write_csr(CVMX_UCTLX_UPHY_PORTX_CTL_STATUS(i, 0),
+			       port_ctl_status.u64);
+	}
+
+	/* Step 3: Configure the reference clock, PHY, and HCLK */
+	clk_rst_ctl.u64 = cvmx_read_csr(CVMX_UCTLX_CLK_RST_CTL(0));
+
+	/*
+	 * If the UCTL looks like it has already been started, skip
+	 * the initialization, otherwise bus errors are obtained.
+	 */
+	if (clk_rst_ctl.s.hrst)
+		goto end_clock;
+	/* 3a */
+	clk_rst_ctl.s.p_por = 1;
+	clk_rst_ctl.s.hrst = 0;
+	clk_rst_ctl.s.p_prst = 0;
+	clk_rst_ctl.s.h_clkdiv_rst = 0;
+	clk_rst_ctl.s.o_clkdiv_rst = 0;
+	clk_rst_ctl.s.h_clkdiv_en = 0;
+	clk_rst_ctl.s.o_clkdiv_en = 0;
+	cvmx_write_csr(CVMX_UCTLX_CLK_RST_CTL(0), clk_rst_ctl.u64);
+
+	/* 3b */
+	clk_rst_ctl.s.p_refclk_sel = is_crystal_clock ? 0 : 1;
+	switch (clock_rate) {
+	default:
+		pr_err("Invalid UCTL clock rate of %u, using 12000000 instead\n",
+			clock_rate);
+		fallthrough;
+	case 12000000:
+		clk_rst_ctl.s.p_refclk_div = 0;
+		break;
+	case 24000000:
+		clk_rst_ctl.s.p_refclk_div = 1;
+		break;
+	case 48000000:
+		clk_rst_ctl.s.p_refclk_div = 2;
+		break;
+	}
+	cvmx_write_csr(CVMX_UCTLX_CLK_RST_CTL(0), clk_rst_ctl.u64);
+
+	/* 3c */
+	div = octeon_get_io_clock_rate() / 130000000ull;
+
+	switch (div) {
+	case 0:
+		div = 1;
+		break;
+	case 1:
+	case 2:
+	case 3:
+	case 4:
+		break;
+	case 5:
+		div = 4;
+		break;
+	case 6:
+	case 7:
+		div = 6;
+		break;
+	case 8:
+	case 9:
+	case 10:
+	case 11:
+		div = 8;
+		break;
+	default:
+		div = 12;
+		break;
+	}
+	clk_rst_ctl.s.h_div = div;
+	cvmx_write_csr(CVMX_UCTLX_CLK_RST_CTL(0), clk_rst_ctl.u64);
+	/* Read it back, */
+	clk_rst_ctl.u64 = cvmx_read_csr(CVMX_UCTLX_CLK_RST_CTL(0));
+	clk_rst_ctl.s.h_clkdiv_en = 1;
+	cvmx_write_csr(CVMX_UCTLX_CLK_RST_CTL(0), clk_rst_ctl.u64);
+	/* 3d */
+	clk_rst_ctl.s.h_clkdiv_rst = 1;
+	cvmx_write_csr(CVMX_UCTLX_CLK_RST_CTL(0), clk_rst_ctl.u64);
+
+	/* 3e: delay 64 io clocks */
+	ndelay(io_clk_64_to_ns);
+
+	/*
+	 * Step 4: Program the power-on reset field in the UCTL
+	 * clock-reset-control register.
+	 */
+	clk_rst_ctl.s.p_por = 0;
+	cvmx_write_csr(CVMX_UCTLX_CLK_RST_CTL(0), clk_rst_ctl.u64);
+
+	/* Step 5:    Wait 3 ms for the PHY clock to start. */
+	mdelay(3);
+
+	/* Steps 6..9 for ATE only, are skipped. */
+
+	/* Step 10: Configure the OHCI_CLK48 and OHCI_CLK12 clocks. */
+	/* 10a */
+	clk_rst_ctl.s.o_clkdiv_rst = 1;
+	cvmx_write_csr(CVMX_UCTLX_CLK_RST_CTL(0), clk_rst_ctl.u64);
+
+	/* 10b */
+	clk_rst_ctl.s.o_clkdiv_en = 1;
+	cvmx_write_csr(CVMX_UCTLX_CLK_RST_CTL(0), clk_rst_ctl.u64);
+
+	/* 10c */
+	ndelay(io_clk_64_to_ns);
+
+	/*
+	 * Step 11: Program the PHY reset field:
+	 * UCTL0_CLK_RST_CTL[P_PRST] = 1
+	 */
+	clk_rst_ctl.s.p_prst = 1;
+	cvmx_write_csr(CVMX_UCTLX_CLK_RST_CTL(0), clk_rst_ctl.u64);
+
+	/* Step 11b */
+	udelay(1);
+
+	/* Step 11c */
+	clk_rst_ctl.s.p_prst = 0;
+	cvmx_write_csr(CVMX_UCTLX_CLK_RST_CTL(0), clk_rst_ctl.u64);
+
+	/* Step 11d */
+	mdelay(1);
+
+	/* Step 11e */
+	clk_rst_ctl.s.p_prst = 1;
+	cvmx_write_csr(CVMX_UCTLX_CLK_RST_CTL(0), clk_rst_ctl.u64);
+
+	/* Step 12: Wait 1 uS. */
+	udelay(1);
+
+	/* Step 13: Program the HRESET_N field: UCTL0_CLK_RST_CTL[HRST] = 1 */
+	clk_rst_ctl.s.hrst = 1;
+	cvmx_write_csr(CVMX_UCTLX_CLK_RST_CTL(0), clk_rst_ctl.u64);
+
+end_clock:
+	/* Set uSOF cycle period to 60,000 bits. */
+	cvmx_write_csr(CVMX_UCTLX_EHCI_FLA(0), 0x20ull);
+
+exit:
+	mutex_unlock(&octeon2_usb_clocks_mutex);
+}
+
+static void octeon2_usb_clocks_stop(void)
+{
+	mutex_lock(&octeon2_usb_clocks_mutex);
+	octeon2_usb_clock_start_cnt--;
+	mutex_unlock(&octeon2_usb_clocks_mutex);
+}
+
+static int octeon_ehci_power_on(struct platform_device *pdev)
+{
+	octeon2_usb_clocks_start(&pdev->dev);
+	return 0;
+}
+
+static void octeon_ehci_power_off(struct platform_device *pdev)
+{
+	octeon2_usb_clocks_stop();
+}
+
+static struct usb_ehci_pdata octeon_ehci_pdata = {
+	/* Octeon EHCI matches CPU endianness. */
+#ifdef __BIG_ENDIAN
+	.big_endian_mmio	= 1,
+#endif
+	/*
+	 * We can DMA from anywhere. But the descriptors must be in
+	 * the lower 4GB.
+	 */
+	.dma_mask_64	= 0,
+	.power_on	= octeon_ehci_power_on,
+	.power_off	= octeon_ehci_power_off,
+};
+
+static void __init octeon_ehci_hw_start(struct device *dev)
+{
+	union cvmx_uctlx_ehci_ctl ehci_ctl;
+
+	octeon2_usb_clocks_start(dev);
+
+	ehci_ctl.u64 = cvmx_read_csr(CVMX_UCTLX_EHCI_CTL(0));
+	/* Use 64-bit addressing. */
+	ehci_ctl.s.ehci_64b_addr_en = 1;
+	ehci_ctl.s.l2c_addr_msb = 0;
+#ifdef __BIG_ENDIAN
+	ehci_ctl.s.l2c_buff_emod = 1; /* Byte swapped. */
+	ehci_ctl.s.l2c_desc_emod = 1; /* Byte swapped. */
+#else
+	ehci_ctl.s.l2c_buff_emod = 0; /* not swapped. */
+	ehci_ctl.s.l2c_desc_emod = 0; /* not swapped. */
+	ehci_ctl.s.inv_reg_a2 = 1;
+#endif
+	cvmx_write_csr(CVMX_UCTLX_EHCI_CTL(0), ehci_ctl.u64);
+
+	octeon2_usb_clocks_stop();
+}
+
+static int __init octeon_ehci_device_init(void)
+{
+	struct platform_device *pd;
+	struct device_node *ehci_node;
+	int ret = 0;
+
+	ehci_node = of_find_node_by_name(NULL, "ehci");
+	if (!ehci_node)
+		return 0;
+
+	pd = of_find_device_by_node(ehci_node);
+	of_node_put(ehci_node);
+	if (!pd)
+		return 0;
+
+	pd->dev.platform_data = &octeon_ehci_pdata;
+	octeon_ehci_hw_start(&pd->dev);
+	put_device(&pd->dev);
+
+	return ret;
+}
+device_initcall(octeon_ehci_device_init);
+
+static int octeon_ohci_power_on(struct platform_device *pdev)
+{
+	octeon2_usb_clocks_start(&pdev->dev);
+	return 0;
+}
+
+static void octeon_ohci_power_off(struct platform_device *pdev)
+{
+	octeon2_usb_clocks_stop();
+}
+
+static struct usb_ohci_pdata octeon_ohci_pdata = {
+	/* Octeon OHCI matches CPU endianness. */
+#ifdef __BIG_ENDIAN
+	.big_endian_mmio	= 1,
+#endif
+	.power_on	= octeon_ohci_power_on,
+	.power_off	= octeon_ohci_power_off,
+};
+
+static void __init octeon_ohci_hw_start(struct device *dev)
+{
+	union cvmx_uctlx_ohci_ctl ohci_ctl;
+
+	octeon2_usb_clocks_start(dev);
+
+	ohci_ctl.u64 = cvmx_read_csr(CVMX_UCTLX_OHCI_CTL(0));
+	ohci_ctl.s.l2c_addr_msb = 0;
+#ifdef __BIG_ENDIAN
+	ohci_ctl.s.l2c_buff_emod = 1; /* Byte swapped. */
+	ohci_ctl.s.l2c_desc_emod = 1; /* Byte swapped. */
+#else
+	ohci_ctl.s.l2c_buff_emod = 0; /* not swapped. */
+	ohci_ctl.s.l2c_desc_emod = 0; /* not swapped. */
+	ohci_ctl.s.inv_reg_a2 = 1;
+#endif
+	cvmx_write_csr(CVMX_UCTLX_OHCI_CTL(0), ohci_ctl.u64);
+
+	octeon2_usb_clocks_stop();
+}
+
+static int __init octeon_ohci_device_init(void)
+{
+	struct platform_device *pd;
+	struct device_node *ohci_node;
+	int ret = 0;
+
+	ohci_node = of_find_node_by_name(NULL, "ohci");
+	if (!ohci_node)
+		return 0;
+
+	pd = of_find_device_by_node(ohci_node);
+	of_node_put(ohci_node);
+	if (!pd)
+		return 0;
+
+	pd->dev.platform_data = &octeon_ohci_pdata;
+	octeon_ohci_hw_start(&pd->dev);
+	put_device(&pd->dev);
+
+	return ret;
+}
+device_initcall(octeon_ohci_device_init);
+
+#endif /* CONFIG_USB */
+
+/* Octeon Random Number Generator.  */
+static int __init octeon_rng_device_init(void)
+{
+	struct platform_device *pd;
+	int ret = 0;
+
+	struct resource rng_resources[] = {
+		{
+			.flags	= IORESOURCE_MEM,
+			.start	= XKPHYS_TO_PHYS(CVMX_RNM_CTL_STATUS),
+			.end	= XKPHYS_TO_PHYS(CVMX_RNM_CTL_STATUS) + 0xf
+		}, {
+			.flags	= IORESOURCE_MEM,
+			.start	= cvmx_build_io_address(8, 0),
+			.end	= cvmx_build_io_address(8, 0) + 0x7
+		}
+	};
+
+	pd = platform_device_alloc("octeon_rng", -1);
+	if (!pd) {
+		ret = -ENOMEM;
+		goto out;
+	}
+
+	ret = platform_device_add_resources(pd, rng_resources,
+					    ARRAY_SIZE(rng_resources));
+	if (ret)
+		goto fail;
+
+	ret = platform_device_add(pd);
+	if (ret)
+		goto fail;
+
+	return ret;
+fail:
+	platform_device_put(pd);
+
+out:
+	return ret;
+}
+device_initcall(octeon_rng_device_init);
+
+static const struct of_device_id octeon_ids[] __initconst = {
+	{ .compatible = "simple-bus", },
+	{ .compatible = "cavium,octeon-6335-uctl", },
+	{ .compatible = "cavium,octeon-5750-usbn", },
+	{ .compatible = "cavium,octeon-3860-bootbus", },
+	{ .compatible = "cavium,mdio-mux", },
+	{ .compatible = "gpio-leds", },
+	{ .compatible = "cavium,octeon-7130-usb-uctl", },
+	{},
+};
+
+static bool __init octeon_has_88e1145(void)
+{
+	return !OCTEON_IS_MODEL(OCTEON_CN52XX) &&
+	       !OCTEON_IS_MODEL(OCTEON_CN6XXX) &&
+	       !OCTEON_IS_MODEL(OCTEON_CN56XX);
+}
+
+static bool __init octeon_has_fixed_link(int ipd_port)
+{
+	switch (cvmx_sysinfo_get()->board_type) {
+	case CVMX_BOARD_TYPE_CN3005_EVB_HS5:
+	case CVMX_BOARD_TYPE_CN3010_EVB_HS5:
+	case CVMX_BOARD_TYPE_CN3020_EVB_HS5:
+	case CVMX_BOARD_TYPE_CUST_NB5:
+	case CVMX_BOARD_TYPE_EBH3100:
+		/* Port 1 on these boards is always gigabit. */
+		return ipd_port == 1;
+	case CVMX_BOARD_TYPE_BBGW_REF:
+		/* Ports 0 and 1 connect to the switch. */
+		return ipd_port == 0 || ipd_port == 1;
+	}
+	return false;
+}
+
+static void __init octeon_fdt_set_phy(int eth, int phy_addr)
+{
+	const __be32 *phy_handle;
+	const __be32 *alt_phy_handle;
+	const __be32 *reg;
+	u32 phandle;
+	int phy;
+	int alt_phy;
+	const char *p;
+	int current_len;
+	char new_name[20];
+
+	phy_handle = fdt_getprop(initial_boot_params, eth, "phy-handle", NULL);
+	if (!phy_handle)
+		return;
+
+	phandle = be32_to_cpup(phy_handle);
+	phy = fdt_node_offset_by_phandle(initial_boot_params, phandle);
+
+	alt_phy_handle = fdt_getprop(initial_boot_params, eth, "cavium,alt-phy-handle", NULL);
+	if (alt_phy_handle) {
+		u32 alt_phandle = be32_to_cpup(alt_phy_handle);
+
+		alt_phy = fdt_node_offset_by_phandle(initial_boot_params, alt_phandle);
+	} else {
+		alt_phy = -1;
+	}
+
+	if (phy_addr < 0 || phy < 0) {
+		/* Delete the PHY things */
+		fdt_nop_property(initial_boot_params, eth, "phy-handle");
+		/* This one may fail */
+		fdt_nop_property(initial_boot_params, eth, "cavium,alt-phy-handle");
+		if (phy >= 0)
+			fdt_nop_node(initial_boot_params, phy);
+		if (alt_phy >= 0)
+			fdt_nop_node(initial_boot_params, alt_phy);
+		return;
+	}
+
+	if (phy_addr >= 256 && alt_phy > 0) {
+		const struct fdt_property *phy_prop;
+		struct fdt_property *alt_prop;
+		fdt32_t phy_handle_name;
+
+		/* Use the alt phy node instead.*/
+		phy_prop = fdt_get_property(initial_boot_params, eth, "phy-handle", NULL);
+		phy_handle_name = phy_prop->nameoff;
+		fdt_nop_node(initial_boot_params, phy);
+		fdt_nop_property(initial_boot_params, eth, "phy-handle");
+		alt_prop = fdt_get_property_w(initial_boot_params, eth, "cavium,alt-phy-handle", NULL);
+		alt_prop->nameoff = phy_handle_name;
+		phy = alt_phy;
+	}
+
+	phy_addr &= 0xff;
+
+	if (octeon_has_88e1145()) {
+		fdt_nop_property(initial_boot_params, phy, "marvell,reg-init");
+		memset(new_name, 0, sizeof(new_name));
+		strcpy(new_name, "marvell,88e1145");
+		p = fdt_getprop(initial_boot_params, phy, "compatible",
+				&current_len);
+		if (p && current_len >= strlen(new_name))
+			fdt_setprop_inplace(initial_boot_params, phy,
+					"compatible", new_name, current_len);
+	}
+
+	reg = fdt_getprop(initial_boot_params, phy, "reg", NULL);
+	if (phy_addr == be32_to_cpup(reg))
+		return;
+
+	fdt_setprop_inplace_cell(initial_boot_params, phy, "reg", phy_addr);
+
+	snprintf(new_name, sizeof(new_name), "ethernet-phy@%x", phy_addr);
+
+	p = fdt_get_name(initial_boot_params, phy, &current_len);
+	if (p && current_len == strlen(new_name))
+		fdt_set_name(initial_boot_params, phy, new_name);
+	else
+		pr_err("Error: could not rename ethernet phy: <%s>", p);
+}
+
+static void __init octeon_fdt_set_mac_addr(int n, u64 *pmac)
+{
+	const u8 *old_mac;
+	int old_len;
+	u8 new_mac[6];
+	u64 mac = *pmac;
+	int r;
+
+	old_mac = fdt_getprop(initial_boot_params, n, "local-mac-address",
+			      &old_len);
+	if (!old_mac || old_len != 6 || is_valid_ether_addr(old_mac))
+		return;
+
+	new_mac[0] = (mac >> 40) & 0xff;
+	new_mac[1] = (mac >> 32) & 0xff;
+	new_mac[2] = (mac >> 24) & 0xff;
+	new_mac[3] = (mac >> 16) & 0xff;
+	new_mac[4] = (mac >> 8) & 0xff;
+	new_mac[5] = mac & 0xff;
+
+	r = fdt_setprop_inplace(initial_boot_params, n, "local-mac-address",
+				new_mac, sizeof(new_mac));
+
+	if (r) {
+		pr_err("Setting \"local-mac-address\" failed %d", r);
+		return;
+	}
+	*pmac = mac + 1;
+}
+
+static void __init octeon_fdt_rm_ethernet(int node)
+{
+	const __be32 *phy_handle;
+
+	phy_handle = fdt_getprop(initial_boot_params, node, "phy-handle", NULL);
+	if (phy_handle) {
+		u32 ph = be32_to_cpup(phy_handle);
+		int p = fdt_node_offset_by_phandle(initial_boot_params, ph);
+
+		if (p >= 0)
+			fdt_nop_node(initial_boot_params, p);
+	}
+	fdt_nop_node(initial_boot_params, node);
+}
+
+static void __init _octeon_rx_tx_delay(int eth, int rx_delay, int tx_delay)
+{
+	fdt_setprop_inplace_cell(initial_boot_params, eth, "rx-delay",
+				 rx_delay);
+	fdt_setprop_inplace_cell(initial_boot_params, eth, "tx-delay",
+				 tx_delay);
+}
+
+static void __init octeon_rx_tx_delay(int eth, int iface, int port)
+{
+	switch (cvmx_sysinfo_get()->board_type) {
+	case CVMX_BOARD_TYPE_CN3005_EVB_HS5:
+		if (iface == 0) {
+			if (port == 0) {
+				/*
+				 * Boards with gigabit WAN ports need a
+				 * different setting that is compatible with
+				 * 100 Mbit settings
+				 */
+				_octeon_rx_tx_delay(eth, 0xc, 0x0c);
+				return;
+			} else if (port == 1) {
+				/* Different config for switch port. */
+				_octeon_rx_tx_delay(eth, 0x0, 0x0);
+				return;
+			}
+		}
+		break;
+	case CVMX_BOARD_TYPE_UBNT_E100:
+		if (iface == 0 && port <= 2) {
+			_octeon_rx_tx_delay(eth, 0x0, 0x10);
+			return;
+		}
+		break;
+	}
+	fdt_nop_property(initial_boot_params, eth, "rx-delay");
+	fdt_nop_property(initial_boot_params, eth, "tx-delay");
+}
+
+static void __init octeon_fdt_pip_port(int iface, int i, int p, int max)
+{
+	char name_buffer[20];
+	int eth;
+	int phy_addr;
+	int ipd_port;
+	int fixed_link;
+
+	snprintf(name_buffer, sizeof(name_buffer), "ethernet@%x", p);
+	eth = fdt_subnode_offset(initial_boot_params, iface, name_buffer);
+	if (eth < 0)
+		return;
+	if (p > max) {
+		pr_debug("Deleting port %x:%x\n", i, p);
+		octeon_fdt_rm_ethernet(eth);
+		return;
+	}
+	if (OCTEON_IS_MODEL(OCTEON_CN68XX))
+		ipd_port = (0x100 * i) + (0x10 * p) + 0x800;
+	else
+		ipd_port = 16 * i + p;
+
+	phy_addr = cvmx_helper_board_get_mii_address(ipd_port);
+	octeon_fdt_set_phy(eth, phy_addr);
+
+	fixed_link = fdt_subnode_offset(initial_boot_params, eth, "fixed-link");
+	if (fixed_link < 0)
+		WARN_ON(octeon_has_fixed_link(ipd_port));
+	else if (!octeon_has_fixed_link(ipd_port))
+		fdt_nop_node(initial_boot_params, fixed_link);
+	octeon_rx_tx_delay(eth, i, p);
+}
+
+static void __init octeon_fdt_pip_iface(int pip, int idx)
+{
+	char name_buffer[20];
+	int iface;
+	int p;
+	int count = 0;
+
+	snprintf(name_buffer, sizeof(name_buffer), "interface@%d", idx);
+	iface = fdt_subnode_offset(initial_boot_params, pip, name_buffer);
+	if (iface < 0)
+		return;
+
+	if (cvmx_helper_interface_enumerate(idx) == 0)
+		count = cvmx_helper_ports_on_interface(idx);
+
+	for (p = 0; p < 16; p++)
+		octeon_fdt_pip_port(iface, idx, p, count - 1);
+}
+
+void __init octeon_fill_mac_addresses(void)
+{
+	const char *alias_prop;
+	char name_buffer[20];
+	u64 mac_addr_base;
+	int aliases;
+	int pip;
+	int i;
+
+	aliases = fdt_path_offset(initial_boot_params, "/aliases");
+	if (aliases < 0)
+		return;
+
+	mac_addr_base =
+		((octeon_bootinfo->mac_addr_base[0] & 0xffull)) << 40 |
+		((octeon_bootinfo->mac_addr_base[1] & 0xffull)) << 32 |
+		((octeon_bootinfo->mac_addr_base[2] & 0xffull)) << 24 |
+		((octeon_bootinfo->mac_addr_base[3] & 0xffull)) << 16 |
+		((octeon_bootinfo->mac_addr_base[4] & 0xffull)) << 8 |
+		 (octeon_bootinfo->mac_addr_base[5] & 0xffull);
+
+	for (i = 0; i < 2; i++) {
+		int mgmt;
+
+		snprintf(name_buffer, sizeof(name_buffer), "mix%d", i);
+		alias_prop = fdt_getprop(initial_boot_params, aliases,
+					 name_buffer, NULL);
+		if (!alias_prop)
+			continue;
+		mgmt = fdt_path_offset(initial_boot_params, alias_prop);
+		if (mgmt < 0)
+			continue;
+		octeon_fdt_set_mac_addr(mgmt, &mac_addr_base);
+	}
+
+	alias_prop = fdt_getprop(initial_boot_params, aliases, "pip", NULL);
+	if (!alias_prop)
+		return;
+
+	pip = fdt_path_offset(initial_boot_params, alias_prop);
+	if (pip < 0)
+		return;
+
+	for (i = 0; i <= 4; i++) {
+		int iface;
+		int p;
+
+		snprintf(name_buffer, sizeof(name_buffer), "interface@%d", i);
+		iface = fdt_subnode_offset(initial_boot_params, pip,
+					   name_buffer);
+		if (iface < 0)
+			continue;
+		for (p = 0; p < 16; p++) {
+			int eth;
+
+			snprintf(name_buffer, sizeof(name_buffer),
+				 "ethernet@%x", p);
+			eth = fdt_subnode_offset(initial_boot_params, iface,
+						 name_buffer);
+			if (eth < 0)
+				continue;
+			octeon_fdt_set_mac_addr(eth, &mac_addr_base);
+		}
+	}
+}
+
+int __init octeon_prune_device_tree(void)
+{
+	int i, max_port, uart_mask;
+	const char *pip_path;
+	const char *alias_prop;
+	char name_buffer[20];
+	int aliases;
+
+	if (fdt_check_header(initial_boot_params))
+		panic("Corrupt Device Tree.");
+
+	WARN(octeon_bootinfo->board_type == CVMX_BOARD_TYPE_CUST_DSR1000N,
+	     "Built-in DTB booting is deprecated on %s. Please switch to use appended DTB.",
+	     cvmx_board_type_to_string(octeon_bootinfo->board_type));
+
+	aliases = fdt_path_offset(initial_boot_params, "/aliases");
+	if (aliases < 0) {
+		pr_err("Error: No /aliases node in device tree.");
+		return -EINVAL;
+	}
+
+	if (OCTEON_IS_MODEL(OCTEON_CN52XX) || OCTEON_IS_MODEL(OCTEON_CN63XX))
+		max_port = 2;
+	else if (OCTEON_IS_MODEL(OCTEON_CN56XX) || OCTEON_IS_MODEL(OCTEON_CN68XX))
+		max_port = 1;
+	else
+		max_port = 0;
+
+	if (octeon_bootinfo->board_type == CVMX_BOARD_TYPE_NIC10E)
+		max_port = 0;
+
+	for (i = 0; i < 2; i++) {
+		int mgmt;
+
+		snprintf(name_buffer, sizeof(name_buffer),
+			 "mix%d", i);
+		alias_prop = fdt_getprop(initial_boot_params, aliases,
+					name_buffer, NULL);
+		if (alias_prop) {
+			mgmt = fdt_path_offset(initial_boot_params, alias_prop);
+			if (mgmt < 0)
+				continue;
+			if (i >= max_port) {
+				pr_debug("Deleting mix%d\n", i);
+				octeon_fdt_rm_ethernet(mgmt);
+				fdt_nop_property(initial_boot_params, aliases,
+						 name_buffer);
+			} else {
+				int phy_addr = cvmx_helper_board_get_mii_address(CVMX_HELPER_BOARD_MGMT_IPD_PORT + i);
+
+				octeon_fdt_set_phy(mgmt, phy_addr);
+			}
+		}
+	}
+
+	pip_path = fdt_getprop(initial_boot_params, aliases, "pip", NULL);
+	if (pip_path) {
+		int pip = fdt_path_offset(initial_boot_params, pip_path);
+
+		if (pip	 >= 0)
+			for (i = 0; i <= 4; i++)
+				octeon_fdt_pip_iface(pip, i);
+	}
+
+	/* I2C */
+	if (OCTEON_IS_MODEL(OCTEON_CN52XX) ||
+	    OCTEON_IS_MODEL(OCTEON_CN63XX) ||
+	    OCTEON_IS_MODEL(OCTEON_CN68XX) ||
+	    OCTEON_IS_MODEL(OCTEON_CN56XX))
+		max_port = 2;
+	else
+		max_port = 1;
+
+	for (i = 0; i < 2; i++) {
+		int i2c;
+
+		snprintf(name_buffer, sizeof(name_buffer),
+			 "twsi%d", i);
+		alias_prop = fdt_getprop(initial_boot_params, aliases,
+					name_buffer, NULL);
+
+		if (alias_prop) {
+			i2c = fdt_path_offset(initial_boot_params, alias_prop);
+			if (i2c < 0)
+				continue;
+			if (i >= max_port) {
+				pr_debug("Deleting twsi%d\n", i);
+				fdt_nop_node(initial_boot_params, i2c);
+				fdt_nop_property(initial_boot_params, aliases,
+						 name_buffer);
+			}
+		}
+	}
+
+	/* SMI/MDIO */
+	if (OCTEON_IS_MODEL(OCTEON_CN68XX))
+		max_port = 4;
+	else if (OCTEON_IS_MODEL(OCTEON_CN52XX) ||
+		 OCTEON_IS_MODEL(OCTEON_CN63XX) ||
+		 OCTEON_IS_MODEL(OCTEON_CN56XX))
+		max_port = 2;
+	else
+		max_port = 1;
+
+	for (i = 0; i < 2; i++) {
+		int i2c;
+
+		snprintf(name_buffer, sizeof(name_buffer),
+			 "smi%d", i);
+		alias_prop = fdt_getprop(initial_boot_params, aliases,
+					name_buffer, NULL);
+		if (alias_prop) {
+			i2c = fdt_path_offset(initial_boot_params, alias_prop);
+			if (i2c < 0)
+				continue;
+			if (i >= max_port) {
+				pr_debug("Deleting smi%d\n", i);
+				fdt_nop_node(initial_boot_params, i2c);
+				fdt_nop_property(initial_boot_params, aliases,
+						 name_buffer);
+			}
+		}
+	}
+
+	/* Serial */
+	uart_mask = 3;
+
+	/* Right now CN52XX is the only chip with a third uart */
+	if (OCTEON_IS_MODEL(OCTEON_CN52XX))
+		uart_mask |= 4; /* uart2 */
+
+	for (i = 0; i < 3; i++) {
+		int uart;
+
+		snprintf(name_buffer, sizeof(name_buffer),
+			 "uart%d", i);
+		alias_prop = fdt_getprop(initial_boot_params, aliases,
+					name_buffer, NULL);
+
+		if (alias_prop) {
+			uart = fdt_path_offset(initial_boot_params, alias_prop);
+			if (uart_mask & (1 << i)) {
+				__be32 f;
+
+				f = cpu_to_be32(octeon_get_io_clock_rate());
+				fdt_setprop_inplace(initial_boot_params,
+						    uart, "clock-frequency",
+						    &f, sizeof(f));
+				continue;
+			}
+			pr_debug("Deleting uart%d\n", i);
+			fdt_nop_node(initial_boot_params, uart);
+			fdt_nop_property(initial_boot_params, aliases,
+					 name_buffer);
+		}
+	}
+
+	/* Compact Flash */
+	alias_prop = fdt_getprop(initial_boot_params, aliases,
+				 "cf0", NULL);
+	if (alias_prop) {
+		union cvmx_mio_boot_reg_cfgx mio_boot_reg_cfg;
+		unsigned long base_ptr, region_base, region_size;
+		unsigned long region1_base = 0;
+		unsigned long region1_size = 0;
+		int cs, bootbus;
+		bool is_16bit = false;
+		bool is_true_ide = false;
+		__be32 new_reg[6];
+		__be32 *ranges;
+		int len;
+
+		int cf = fdt_path_offset(initial_boot_params, alias_prop);
+
+		base_ptr = 0;
+		if (octeon_bootinfo->major_version == 1
+			&& octeon_bootinfo->minor_version >= 1) {
+			if (octeon_bootinfo->compact_flash_common_base_addr)
+				base_ptr = octeon_bootinfo->compact_flash_common_base_addr;
+		} else {
+			base_ptr = 0x1d000800;
+		}
+
+		if (!base_ptr)
+			goto no_cf;
+
+		/* Find CS0 region. */
+		for (cs = 0; cs < 8; cs++) {
+			mio_boot_reg_cfg.u64 = cvmx_read_csr(CVMX_MIO_BOOT_REG_CFGX(cs));
+			region_base = mio_boot_reg_cfg.s.base << 16;
+			region_size = (mio_boot_reg_cfg.s.size + 1) << 16;
+			if (mio_boot_reg_cfg.s.en && base_ptr >= region_base
+				&& base_ptr < region_base + region_size) {
+				is_16bit = mio_boot_reg_cfg.s.width;
+				break;
+			}
+		}
+		if (cs >= 7) {
+			/* cs and cs + 1 are CS0 and CS1, both must be less than 8. */
+			goto no_cf;
+		}
+
+		if (!(base_ptr & 0xfffful)) {
+			/*
+			 * Boot loader signals availability of DMA (true_ide
+			 * mode) by setting low order bits of base_ptr to
+			 * zero.
+			 */
+
+			/* Asume that CS1 immediately follows. */
+			mio_boot_reg_cfg.u64 =
+				cvmx_read_csr(CVMX_MIO_BOOT_REG_CFGX(cs + 1));
+			region1_base = mio_boot_reg_cfg.s.base << 16;
+			region1_size = (mio_boot_reg_cfg.s.size + 1) << 16;
+			if (!mio_boot_reg_cfg.s.en)
+				goto no_cf;
+			is_true_ide = true;
+
+		} else {
+			fdt_nop_property(initial_boot_params, cf, "cavium,true-ide");
+			fdt_nop_property(initial_boot_params, cf, "cavium,dma-engine-handle");
+			if (!is_16bit) {
+				__be32 width = cpu_to_be32(8);
+
+				fdt_setprop_inplace(initial_boot_params, cf,
+						"cavium,bus-width", &width, sizeof(width));
+			}
+		}
+		new_reg[0] = cpu_to_be32(cs);
+		new_reg[1] = cpu_to_be32(0);
+		new_reg[2] = cpu_to_be32(0x10000);
+		new_reg[3] = cpu_to_be32(cs + 1);
+		new_reg[4] = cpu_to_be32(0);
+		new_reg[5] = cpu_to_be32(0x10000);
+		fdt_setprop_inplace(initial_boot_params, cf,
+				    "reg",  new_reg, sizeof(new_reg));
+
+		bootbus = fdt_parent_offset(initial_boot_params, cf);
+		if (bootbus < 0)
+			goto no_cf;
+		ranges = fdt_getprop_w(initial_boot_params, bootbus, "ranges", &len);
+		if (!ranges || len < (5 * 8 * sizeof(__be32)))
+			goto no_cf;
+
+		ranges[(cs * 5) + 2] = cpu_to_be32(region_base >> 32);
+		ranges[(cs * 5) + 3] = cpu_to_be32(region_base & 0xffffffff);
+		ranges[(cs * 5) + 4] = cpu_to_be32(region_size);
+		if (is_true_ide) {
+			cs++;
+			ranges[(cs * 5) + 2] = cpu_to_be32(region1_base >> 32);
+			ranges[(cs * 5) + 3] = cpu_to_be32(region1_base & 0xffffffff);
+			ranges[(cs * 5) + 4] = cpu_to_be32(region1_size);
+		}
+		goto end_cf;
+no_cf:
+		fdt_nop_node(initial_boot_params, cf);
+
+end_cf:
+		;
+	}
+
+	/* 8 char LED */
+	alias_prop = fdt_getprop(initial_boot_params, aliases,
+				 "led0", NULL);
+	if (alias_prop) {
+		union cvmx_mio_boot_reg_cfgx mio_boot_reg_cfg;
+		unsigned long base_ptr, region_base, region_size;
+		int cs, bootbus;
+		__be32 new_reg[6];
+		__be32 *ranges;
+		int len;
+		int led = fdt_path_offset(initial_boot_params, alias_prop);
+
+		base_ptr = octeon_bootinfo->led_display_base_addr;
+		if (base_ptr == 0)
+			goto no_led;
+		/* Find CS0 region. */
+		for (cs = 0; cs < 8; cs++) {
+			mio_boot_reg_cfg.u64 = cvmx_read_csr(CVMX_MIO_BOOT_REG_CFGX(cs));
+			region_base = mio_boot_reg_cfg.s.base << 16;
+			region_size = (mio_boot_reg_cfg.s.size + 1) << 16;
+			if (mio_boot_reg_cfg.s.en && base_ptr >= region_base
+				&& base_ptr < region_base + region_size)
+				break;
+		}
+
+		if (cs > 7)
+			goto no_led;
+
+		new_reg[0] = cpu_to_be32(cs);
+		new_reg[1] = cpu_to_be32(0x20);
+		new_reg[2] = cpu_to_be32(0x20);
+		new_reg[3] = cpu_to_be32(cs);
+		new_reg[4] = cpu_to_be32(0);
+		new_reg[5] = cpu_to_be32(0x20);
+		fdt_setprop_inplace(initial_boot_params, led,
+				    "reg",  new_reg, sizeof(new_reg));
+
+		bootbus = fdt_parent_offset(initial_boot_params, led);
+		if (bootbus < 0)
+			goto no_led;
+		ranges = fdt_getprop_w(initial_boot_params, bootbus, "ranges", &len);
+		if (!ranges || len < (5 * 8 * sizeof(__be32)))
+			goto no_led;
+
+		ranges[(cs * 5) + 2] = cpu_to_be32(region_base >> 32);
+		ranges[(cs * 5) + 3] = cpu_to_be32(region_base & 0xffffffff);
+		ranges[(cs * 5) + 4] = cpu_to_be32(region_size);
+		goto end_led;
+
+no_led:
+		fdt_nop_node(initial_boot_params, led);
+end_led:
+		;
+	}
+
+#ifdef CONFIG_USB
+	/* OHCI/UHCI USB */
+	alias_prop = fdt_getprop(initial_boot_params, aliases,
+				 "uctl", NULL);
+	if (alias_prop) {
+		int uctl = fdt_path_offset(initial_boot_params, alias_prop);
+
+		if (uctl >= 0 && (!OCTEON_IS_MODEL(OCTEON_CN6XXX) ||
+				  octeon_bootinfo->board_type == CVMX_BOARD_TYPE_NIC2E)) {
+			pr_debug("Deleting uctl\n");
+			fdt_nop_node(initial_boot_params, uctl);
+			fdt_nop_property(initial_boot_params, aliases, "uctl");
+		} else if (octeon_bootinfo->board_type == CVMX_BOARD_TYPE_NIC10E ||
+			   octeon_bootinfo->board_type == CVMX_BOARD_TYPE_NIC4E) {
+			/* Missing "refclk-type" defaults to crystal. */
+			fdt_nop_property(initial_boot_params, uctl, "refclk-type");
+		}
+	}
+
+	/* DWC2 USB */
+	alias_prop = fdt_getprop(initial_boot_params, aliases,
+				 "usbn", NULL);
+	if (alias_prop) {
+		int usbn = fdt_path_offset(initial_boot_params, alias_prop);
+
+		if (usbn >= 0 && (current_cpu_type() == CPU_CAVIUM_OCTEON2 ||
+				  !octeon_has_feature(OCTEON_FEATURE_USB))) {
+			pr_debug("Deleting usbn\n");
+			fdt_nop_node(initial_boot_params, usbn);
+			fdt_nop_property(initial_boot_params, aliases, "usbn");
+		} else  {
+			__be32 new_f[1];
+			enum cvmx_helper_board_usb_clock_types c;
+
+			c = __cvmx_helper_board_usb_get_clock_type();
+			switch (c) {
+			case USB_CLOCK_TYPE_REF_48:
+				new_f[0] = cpu_to_be32(48000000);
+				fdt_setprop_inplace(initial_boot_params, usbn,
+						    "refclk-frequency",  new_f, sizeof(new_f));
+				fallthrough;
+			case USB_CLOCK_TYPE_REF_12:
+				/* Missing "refclk-type" defaults to external. */
+				fdt_nop_property(initial_boot_params, usbn, "refclk-type");
+				break;
+			default:
+				break;
+			}
+		}
+	}
+#endif
+
+	return 0;
+}
+
+static int __init octeon_publish_devices(void)
+{
+	return of_platform_populate(NULL, octeon_ids, NULL, NULL);
+}
+arch_initcall(octeon_publish_devices);
diff --git a/arch/mips/cavium-octeon/octeon-usb.c b/arch/mips/cavium-octeon/octeon-usb.c
new file mode 100644
index 000000000..5cffe1ed2
--- /dev/null
+++ b/arch/mips/cavium-octeon/octeon-usb.c
@@ -0,0 +1,550 @@
+/*
+ * XHCI HCD glue for Cavium Octeon III SOCs.
+ *
+ * Copyright (C) 2010-2017 Cavium Networks
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/mutex.h>
+#include <linux/delay.h>
+#include <linux/of_platform.h>
+#include <linux/io.h>
+
+#include <asm/octeon/octeon.h>
+
+/* USB Control Register */
+union cvm_usbdrd_uctl_ctl {
+	uint64_t u64;
+	struct cvm_usbdrd_uctl_ctl_s {
+	/* 1 = BIST and set all USB RAMs to 0x0, 0 = BIST */
+	__BITFIELD_FIELD(uint64_t clear_bist:1,
+	/* 1 = Start BIST and cleared by hardware */
+	__BITFIELD_FIELD(uint64_t start_bist:1,
+	/* Reference clock select for SuperSpeed and HighSpeed PLLs:
+	 *	0x0 = Both PLLs use DLMC_REF_CLK0 for reference clock
+	 *	0x1 = Both PLLs use DLMC_REF_CLK1 for reference clock
+	 *	0x2 = SuperSpeed PLL uses DLMC_REF_CLK0 for reference clock &
+	 *	      HighSpeed PLL uses PLL_REF_CLK for reference clck
+	 *	0x3 = SuperSpeed PLL uses DLMC_REF_CLK1 for reference clock &
+	 *	      HighSpeed PLL uses PLL_REF_CLK for reference clck
+	 */
+	__BITFIELD_FIELD(uint64_t ref_clk_sel:2,
+	/* 1 = Spread-spectrum clock enable, 0 = SS clock disable */
+	__BITFIELD_FIELD(uint64_t ssc_en:1,
+	/* Spread-spectrum clock modulation range:
+	 *	0x0 = -4980 ppm downspread
+	 *	0x1 = -4492 ppm downspread
+	 *	0x2 = -4003 ppm downspread
+	 *	0x3 - 0x7 = Reserved
+	 */
+	__BITFIELD_FIELD(uint64_t ssc_range:3,
+	/* Enable non-standard oscillator frequencies:
+	 *	[55:53] = modules -1
+	 *	[52:47] = 2's complement push amount, 0 = Feature disabled
+	 */
+	__BITFIELD_FIELD(uint64_t ssc_ref_clk_sel:9,
+	/* Reference clock multiplier for non-standard frequencies:
+	 *	0x19 = 100MHz on DLMC_REF_CLK* if REF_CLK_SEL = 0x0 or 0x1
+	 *	0x28 = 125MHz on DLMC_REF_CLK* if REF_CLK_SEL = 0x0 or 0x1
+	 *	0x32 =  50MHz on DLMC_REF_CLK* if REF_CLK_SEL = 0x0 or 0x1
+	 *	Other Values = Reserved
+	 */
+	__BITFIELD_FIELD(uint64_t mpll_multiplier:7,
+	/* Enable reference clock to prescaler for SuperSpeed functionality.
+	 * Should always be set to "1"
+	 */
+	__BITFIELD_FIELD(uint64_t ref_ssp_en:1,
+	/* Divide the reference clock by 2 before entering the
+	 * REF_CLK_FSEL divider:
+	 *	If REF_CLK_SEL = 0x0 or 0x1, then only 0x0 is legal
+	 *	If REF_CLK_SEL = 0x2 or 0x3, then:
+	 *		0x1 = DLMC_REF_CLK* is 125MHz
+	 *		0x0 = DLMC_REF_CLK* is another supported frequency
+	 */
+	__BITFIELD_FIELD(uint64_t ref_clk_div2:1,
+	/* Select reference clock freqnuency for both PLL blocks:
+	 *	0x27 = REF_CLK_SEL is 0x0 or 0x1
+	 *	0x07 = REF_CLK_SEL is 0x2 or 0x3
+	 */
+	__BITFIELD_FIELD(uint64_t ref_clk_fsel:6,
+	/* Reserved */
+	__BITFIELD_FIELD(uint64_t reserved_31_31:1,
+	/* Controller clock enable. */
+	__BITFIELD_FIELD(uint64_t h_clk_en:1,
+	/* Select bypass input to controller clock divider:
+	 *	0x0 = Use divided coprocessor clock from H_CLKDIV
+	 *	0x1 = Use clock from GPIO pins
+	 */
+	__BITFIELD_FIELD(uint64_t h_clk_byp_sel:1,
+	/* Reset controller clock divider. */
+	__BITFIELD_FIELD(uint64_t h_clkdiv_rst:1,
+	/* Reserved */
+	__BITFIELD_FIELD(uint64_t reserved_27_27:1,
+	/* Clock divider select:
+	 *	0x0 = divide by 1
+	 *	0x1 = divide by 2
+	 *	0x2 = divide by 4
+	 *	0x3 = divide by 6
+	 *	0x4 = divide by 8
+	 *	0x5 = divide by 16
+	 *	0x6 = divide by 24
+	 *	0x7 = divide by 32
+	 */
+	__BITFIELD_FIELD(uint64_t h_clkdiv_sel:3,
+	/* Reserved */
+	__BITFIELD_FIELD(uint64_t reserved_22_23:2,
+	/* USB3 port permanently attached: 0x0 = No, 0x1 = Yes */
+	__BITFIELD_FIELD(uint64_t usb3_port_perm_attach:1,
+	/* USB2 port permanently attached: 0x0 = No, 0x1 = Yes */
+	__BITFIELD_FIELD(uint64_t usb2_port_perm_attach:1,
+	/* Reserved */
+	__BITFIELD_FIELD(uint64_t reserved_19_19:1,
+	/* Disable SuperSpeed PHY: 0x0 = No, 0x1 = Yes */
+	__BITFIELD_FIELD(uint64_t usb3_port_disable:1,
+	/* Reserved */
+	__BITFIELD_FIELD(uint64_t reserved_17_17:1,
+	/* Disable HighSpeed PHY: 0x0 = No, 0x1 = Yes */
+	__BITFIELD_FIELD(uint64_t usb2_port_disable:1,
+	/* Reserved */
+	__BITFIELD_FIELD(uint64_t reserved_15_15:1,
+	/* Enable PHY SuperSpeed block power: 0x0 = No, 0x1 = Yes */
+	__BITFIELD_FIELD(uint64_t ss_power_en:1,
+	/* Reserved */
+	__BITFIELD_FIELD(uint64_t reserved_13_13:1,
+	/* Enable PHY HighSpeed block power: 0x0 = No, 0x1 = Yes */
+	__BITFIELD_FIELD(uint64_t hs_power_en:1,
+	/* Reserved */
+	__BITFIELD_FIELD(uint64_t reserved_5_11:7,
+	/* Enable USB UCTL interface clock: 0xx = No, 0x1 = Yes */
+	__BITFIELD_FIELD(uint64_t csclk_en:1,
+	/* Controller mode: 0x0 = Host, 0x1 = Device */
+	__BITFIELD_FIELD(uint64_t drd_mode:1,
+	/* PHY reset */
+	__BITFIELD_FIELD(uint64_t uphy_rst:1,
+	/* Software reset UAHC */
+	__BITFIELD_FIELD(uint64_t uahc_rst:1,
+	/* Software resets UCTL */
+	__BITFIELD_FIELD(uint64_t uctl_rst:1,
+	;)))))))))))))))))))))))))))))))))
+	} s;
+};
+
+/* UAHC Configuration Register */
+union cvm_usbdrd_uctl_host_cfg {
+	uint64_t u64;
+	struct cvm_usbdrd_uctl_host_cfg_s {
+	/* Reserved */
+	__BITFIELD_FIELD(uint64_t reserved_60_63:4,
+	/* Indicates minimum value of all received BELT values */
+	__BITFIELD_FIELD(uint64_t host_current_belt:12,
+	/* Reserved */
+	__BITFIELD_FIELD(uint64_t reserved_38_47:10,
+	/* HS jitter adjustment */
+	__BITFIELD_FIELD(uint64_t fla:6,
+	/* Reserved */
+	__BITFIELD_FIELD(uint64_t reserved_29_31:3,
+	/* Bus-master enable: 0x0 = Disabled (stall DMAs), 0x1 = enabled */
+	__BITFIELD_FIELD(uint64_t bme:1,
+	/* Overcurrent protection enable: 0x0 = unavailable, 0x1 = available */
+	__BITFIELD_FIELD(uint64_t oci_en:1,
+	/* Overcurrent sene selection:
+	 *	0x0 = Overcurrent indication from off-chip is active-low
+	 *	0x1 = Overcurrent indication from off-chip is active-high
+	 */
+	__BITFIELD_FIELD(uint64_t oci_active_high_en:1,
+	/* Port power control enable: 0x0 = unavailable, 0x1 = available */
+	__BITFIELD_FIELD(uint64_t ppc_en:1,
+	/* Port power control sense selection:
+	 *	0x0 = Port power to off-chip is active-low
+	 *	0x1 = Port power to off-chip is active-high
+	 */
+	__BITFIELD_FIELD(uint64_t ppc_active_high_en:1,
+	/* Reserved */
+	__BITFIELD_FIELD(uint64_t reserved_0_23:24,
+	;)))))))))))
+	} s;
+};
+
+/* UCTL Shim Features Register */
+union cvm_usbdrd_uctl_shim_cfg {
+	uint64_t u64;
+	struct cvm_usbdrd_uctl_shim_cfg_s {
+	/* Out-of-bound UAHC register access: 0 = read, 1 = write */
+	__BITFIELD_FIELD(uint64_t xs_ncb_oob_wrn:1,
+	/* Reserved */
+	__BITFIELD_FIELD(uint64_t reserved_60_62:3,
+	/* SRCID error log for out-of-bound UAHC register access:
+	 *	[59:58] = chipID
+	 *	[57] = Request source: 0 = core, 1 = NCB-device
+	 *	[56:51] = Core/NCB-device number, [56] always 0 for NCB devices
+	 *	[50:48] = SubID
+	 */
+	__BITFIELD_FIELD(uint64_t xs_ncb_oob_osrc:12,
+	/* Error log for bad UAHC DMA access: 0 = Read log, 1 = Write log */
+	__BITFIELD_FIELD(uint64_t xm_bad_dma_wrn:1,
+	/* Reserved */
+	__BITFIELD_FIELD(uint64_t reserved_44_46:3,
+	/* Encoded error type for bad UAHC DMA */
+	__BITFIELD_FIELD(uint64_t xm_bad_dma_type:4,
+	/* Reserved */
+	__BITFIELD_FIELD(uint64_t reserved_13_39:27,
+	/* Select the IOI read command used by DMA accesses */
+	__BITFIELD_FIELD(uint64_t dma_read_cmd:1,
+	/* Reserved */
+	__BITFIELD_FIELD(uint64_t reserved_10_11:2,
+	/* Select endian format for DMA accesses to the L2c:
+	 *	0x0 = Little endian
+	 *`	0x1 = Big endian
+	 *	0x2 = Reserved
+	 *	0x3 = Reserved
+	 */
+	__BITFIELD_FIELD(uint64_t dma_endian_mode:2,
+	/* Reserved */
+	__BITFIELD_FIELD(uint64_t reserved_2_7:6,
+	/* Select endian format for IOI CSR access to UAHC:
+	 *	0x0 = Little endian
+	 *`	0x1 = Big endian
+	 *	0x2 = Reserved
+	 *	0x3 = Reserved
+	 */
+	__BITFIELD_FIELD(uint64_t csr_endian_mode:2,
+	;))))))))))))
+	} s;
+};
+
+#define OCTEON_H_CLKDIV_SEL		8
+#define OCTEON_MIN_H_CLK_RATE		150000000
+#define OCTEON_MAX_H_CLK_RATE		300000000
+
+static DEFINE_MUTEX(dwc3_octeon_clocks_mutex);
+static uint8_t clk_div[OCTEON_H_CLKDIV_SEL] = {1, 2, 4, 6, 8, 16, 24, 32};
+
+
+static int dwc3_octeon_config_power(struct device *dev, u64 base)
+{
+#define UCTL_HOST_CFG	0xe0
+	union cvm_usbdrd_uctl_host_cfg uctl_host_cfg;
+	union cvmx_gpio_bit_cfgx gpio_bit;
+	uint32_t gpio_pwr[3];
+	int gpio, len, power_active_low;
+	struct device_node *node = dev->of_node;
+	int index = (base >> 24) & 1;
+
+	if (of_find_property(node, "power", &len) != NULL) {
+		if (len == 12) {
+			of_property_read_u32_array(node, "power", gpio_pwr, 3);
+			power_active_low = gpio_pwr[2] & 0x01;
+			gpio = gpio_pwr[1];
+		} else if (len == 8) {
+			of_property_read_u32_array(node, "power", gpio_pwr, 2);
+			power_active_low = 0;
+			gpio = gpio_pwr[1];
+		} else {
+			dev_err(dev, "dwc3 controller clock init failure.\n");
+			return -EINVAL;
+		}
+		if ((OCTEON_IS_MODEL(OCTEON_CN73XX) ||
+		    OCTEON_IS_MODEL(OCTEON_CNF75XX))
+		    && gpio <= 31) {
+			gpio_bit.u64 = cvmx_read_csr(CVMX_GPIO_BIT_CFGX(gpio));
+			gpio_bit.s.tx_oe = 1;
+			gpio_bit.s.output_sel = (index == 0 ? 0x14 : 0x15);
+			cvmx_write_csr(CVMX_GPIO_BIT_CFGX(gpio), gpio_bit.u64);
+		} else if (gpio <= 15) {
+			gpio_bit.u64 = cvmx_read_csr(CVMX_GPIO_BIT_CFGX(gpio));
+			gpio_bit.s.tx_oe = 1;
+			gpio_bit.s.output_sel = (index == 0 ? 0x14 : 0x19);
+			cvmx_write_csr(CVMX_GPIO_BIT_CFGX(gpio), gpio_bit.u64);
+		} else {
+			gpio_bit.u64 = cvmx_read_csr(CVMX_GPIO_XBIT_CFGX(gpio));
+			gpio_bit.s.tx_oe = 1;
+			gpio_bit.s.output_sel = (index == 0 ? 0x14 : 0x19);
+			cvmx_write_csr(CVMX_GPIO_XBIT_CFGX(gpio), gpio_bit.u64);
+		}
+
+		/* Enable XHCI power control and set if active high or low. */
+		uctl_host_cfg.u64 = cvmx_read_csr(base + UCTL_HOST_CFG);
+		uctl_host_cfg.s.ppc_en = 1;
+		uctl_host_cfg.s.ppc_active_high_en = !power_active_low;
+		cvmx_write_csr(base + UCTL_HOST_CFG, uctl_host_cfg.u64);
+	} else {
+		/* Disable XHCI power control and set if active high. */
+		uctl_host_cfg.u64 = cvmx_read_csr(base + UCTL_HOST_CFG);
+		uctl_host_cfg.s.ppc_en = 0;
+		uctl_host_cfg.s.ppc_active_high_en = 0;
+		cvmx_write_csr(base + UCTL_HOST_CFG, uctl_host_cfg.u64);
+		dev_warn(dev, "dwc3 controller clock init failure.\n");
+	}
+	return 0;
+}
+
+static int dwc3_octeon_clocks_start(struct device *dev, u64 base)
+{
+	union cvm_usbdrd_uctl_ctl uctl_ctl;
+	int ref_clk_sel = 2;
+	u64 div;
+	u32 clock_rate;
+	int mpll_mul;
+	int i;
+	u64 h_clk_rate;
+	u64 uctl_ctl_reg = base;
+
+	if (dev->of_node) {
+		const char *ss_clock_type;
+		const char *hs_clock_type;
+
+		i = of_property_read_u32(dev->of_node,
+					 "refclk-frequency", &clock_rate);
+		if (i) {
+			pr_err("No UCTL \"refclk-frequency\"\n");
+			return -EINVAL;
+		}
+		i = of_property_read_string(dev->of_node,
+					    "refclk-type-ss", &ss_clock_type);
+		if (i) {
+			pr_err("No UCTL \"refclk-type-ss\"\n");
+			return -EINVAL;
+		}
+		i = of_property_read_string(dev->of_node,
+					    "refclk-type-hs", &hs_clock_type);
+		if (i) {
+			pr_err("No UCTL \"refclk-type-hs\"\n");
+			return -EINVAL;
+		}
+		if (strcmp("dlmc_ref_clk0", ss_clock_type) == 0) {
+			if (strcmp(hs_clock_type, "dlmc_ref_clk0") == 0)
+				ref_clk_sel = 0;
+			else if (strcmp(hs_clock_type, "pll_ref_clk") == 0)
+				ref_clk_sel = 2;
+			else
+				pr_err("Invalid HS clock type %s, using  pll_ref_clk instead\n",
+				       hs_clock_type);
+		} else if (strcmp(ss_clock_type, "dlmc_ref_clk1") == 0) {
+			if (strcmp(hs_clock_type, "dlmc_ref_clk1") == 0)
+				ref_clk_sel = 1;
+			else if (strcmp(hs_clock_type, "pll_ref_clk") == 0)
+				ref_clk_sel = 3;
+			else {
+				pr_err("Invalid HS clock type %s, using  pll_ref_clk instead\n",
+				       hs_clock_type);
+				ref_clk_sel = 3;
+			}
+		} else
+			pr_err("Invalid SS clock type %s, using  dlmc_ref_clk0 instead\n",
+			       ss_clock_type);
+
+		if ((ref_clk_sel == 0 || ref_clk_sel == 1) &&
+				  (clock_rate != 100000000))
+			pr_err("Invalid UCTL clock rate of %u, using 100000000 instead\n",
+			       clock_rate);
+
+	} else {
+		pr_err("No USB UCTL device node\n");
+		return -EINVAL;
+	}
+
+	/*
+	 * Step 1: Wait for all voltages to be stable...that surely
+	 *         happened before starting the kernel. SKIP
+	 */
+
+	/* Step 2: Select GPIO for overcurrent indication, if desired. SKIP */
+
+	/* Step 3: Assert all resets. */
+	uctl_ctl.u64 = cvmx_read_csr(uctl_ctl_reg);
+	uctl_ctl.s.uphy_rst = 1;
+	uctl_ctl.s.uahc_rst = 1;
+	uctl_ctl.s.uctl_rst = 1;
+	cvmx_write_csr(uctl_ctl_reg, uctl_ctl.u64);
+
+	/* Step 4a: Reset the clock dividers. */
+	uctl_ctl.u64 = cvmx_read_csr(uctl_ctl_reg);
+	uctl_ctl.s.h_clkdiv_rst = 1;
+	cvmx_write_csr(uctl_ctl_reg, uctl_ctl.u64);
+
+	/* Step 4b: Select controller clock frequency. */
+	for (div = 0; div < OCTEON_H_CLKDIV_SEL; div++) {
+		h_clk_rate = octeon_get_io_clock_rate() / clk_div[div];
+		if (h_clk_rate <= OCTEON_MAX_H_CLK_RATE &&
+				 h_clk_rate >= OCTEON_MIN_H_CLK_RATE)
+			break;
+	}
+	uctl_ctl.u64 = cvmx_read_csr(uctl_ctl_reg);
+	uctl_ctl.s.h_clkdiv_sel = div;
+	uctl_ctl.s.h_clk_en = 1;
+	cvmx_write_csr(uctl_ctl_reg, uctl_ctl.u64);
+	uctl_ctl.u64 = cvmx_read_csr(uctl_ctl_reg);
+	if ((div != uctl_ctl.s.h_clkdiv_sel) || (!uctl_ctl.s.h_clk_en)) {
+		dev_err(dev, "dwc3 controller clock init failure.\n");
+			return -EINVAL;
+	}
+
+	/* Step 4c: Deassert the controller clock divider reset. */
+	uctl_ctl.u64 = cvmx_read_csr(uctl_ctl_reg);
+	uctl_ctl.s.h_clkdiv_rst = 0;
+	cvmx_write_csr(uctl_ctl_reg, uctl_ctl.u64);
+
+	/* Step 5a: Reference clock configuration. */
+	uctl_ctl.u64 = cvmx_read_csr(uctl_ctl_reg);
+	uctl_ctl.s.ref_clk_sel = ref_clk_sel;
+	uctl_ctl.s.ref_clk_fsel = 0x07;
+	uctl_ctl.s.ref_clk_div2 = 0;
+	switch (clock_rate) {
+	default:
+		dev_err(dev, "Invalid ref_clk %u, using 100000000 instead\n",
+			clock_rate);
+		fallthrough;
+	case 100000000:
+		mpll_mul = 0x19;
+		if (ref_clk_sel < 2)
+			uctl_ctl.s.ref_clk_fsel = 0x27;
+		break;
+	case 50000000:
+		mpll_mul = 0x32;
+		break;
+	case 125000000:
+		mpll_mul = 0x28;
+		break;
+	}
+	uctl_ctl.s.mpll_multiplier = mpll_mul;
+
+	/* Step 5b: Configure and enable spread-spectrum for SuperSpeed. */
+	uctl_ctl.s.ssc_en = 1;
+
+	/* Step 5c: Enable SuperSpeed. */
+	uctl_ctl.s.ref_ssp_en = 1;
+
+	/* Step 5d: Configure PHYs. SKIP */
+
+	/* Step 6a & 6b: Power up PHYs. */
+	uctl_ctl.s.hs_power_en = 1;
+	uctl_ctl.s.ss_power_en = 1;
+	cvmx_write_csr(uctl_ctl_reg, uctl_ctl.u64);
+
+	/* Step 7: Wait 10 controller-clock cycles to take effect. */
+	udelay(10);
+
+	/* Step 8a: Deassert UCTL reset signal. */
+	uctl_ctl.u64 = cvmx_read_csr(uctl_ctl_reg);
+	uctl_ctl.s.uctl_rst = 0;
+	cvmx_write_csr(uctl_ctl_reg, uctl_ctl.u64);
+
+	/* Step 8b: Wait 10 controller-clock cycles. */
+	udelay(10);
+
+	/* Steo 8c: Setup power-power control. */
+	if (dwc3_octeon_config_power(dev, base)) {
+		dev_err(dev, "Error configuring power.\n");
+		return -EINVAL;
+	}
+
+	/* Step 8d: Deassert UAHC reset signal. */
+	uctl_ctl.u64 = cvmx_read_csr(uctl_ctl_reg);
+	uctl_ctl.s.uahc_rst = 0;
+	cvmx_write_csr(uctl_ctl_reg, uctl_ctl.u64);
+
+	/* Step 8e: Wait 10 controller-clock cycles. */
+	udelay(10);
+
+	/* Step 9: Enable conditional coprocessor clock of UCTL. */
+	uctl_ctl.u64 = cvmx_read_csr(uctl_ctl_reg);
+	uctl_ctl.s.csclk_en = 1;
+	cvmx_write_csr(uctl_ctl_reg, uctl_ctl.u64);
+
+	/*Step 10: Set for host mode only. */
+	uctl_ctl.u64 = cvmx_read_csr(uctl_ctl_reg);
+	uctl_ctl.s.drd_mode = 0;
+	cvmx_write_csr(uctl_ctl_reg, uctl_ctl.u64);
+
+	return 0;
+}
+
+static void __init dwc3_octeon_set_endian_mode(u64 base)
+{
+#define UCTL_SHIM_CFG	0xe8
+	union cvm_usbdrd_uctl_shim_cfg shim_cfg;
+
+	shim_cfg.u64 = cvmx_read_csr(base + UCTL_SHIM_CFG);
+#ifdef __BIG_ENDIAN
+	shim_cfg.s.dma_endian_mode = 1;
+	shim_cfg.s.csr_endian_mode = 1;
+#else
+	shim_cfg.s.dma_endian_mode = 0;
+	shim_cfg.s.csr_endian_mode = 0;
+#endif
+	cvmx_write_csr(base + UCTL_SHIM_CFG, shim_cfg.u64);
+}
+
+#define CVMX_USBDRDX_UCTL_CTL(index)				\
+		(CVMX_ADD_IO_SEG(0x0001180068000000ull) +	\
+		((index & 1) * 0x1000000ull))
+static void __init dwc3_octeon_phy_reset(u64 base)
+{
+	union cvm_usbdrd_uctl_ctl uctl_ctl;
+	int index = (base >> 24) & 1;
+
+	uctl_ctl.u64 = cvmx_read_csr(CVMX_USBDRDX_UCTL_CTL(index));
+	uctl_ctl.s.uphy_rst = 0;
+	cvmx_write_csr(CVMX_USBDRDX_UCTL_CTL(index), uctl_ctl.u64);
+}
+
+static int __init dwc3_octeon_device_init(void)
+{
+	const char compat_node_name[] = "cavium,octeon-7130-usb-uctl";
+	struct platform_device *pdev;
+	struct device_node *node;
+	struct resource *res;
+	void __iomem *base;
+
+	/*
+	 * There should only be three universal controllers, "uctl"
+	 * in the device tree. Two USB and a SATA, which we ignore.
+	 */
+	node = NULL;
+	do {
+		node = of_find_node_by_name(node, "uctl");
+		if (!node)
+			return -ENODEV;
+
+		if (of_device_is_compatible(node, compat_node_name)) {
+			pdev = of_find_device_by_node(node);
+			if (!pdev)
+				return -ENODEV;
+
+			/*
+			 * The code below maps in the registers necessary for
+			 * setting up the clocks and reseting PHYs. We must
+			 * release the resources so the dwc3 subsystem doesn't
+			 * know the difference.
+			 */
+			base = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
+			if (IS_ERR(base)) {
+				put_device(&pdev->dev);
+				return PTR_ERR(base);
+			}
+
+			mutex_lock(&dwc3_octeon_clocks_mutex);
+			dwc3_octeon_clocks_start(&pdev->dev, (u64)base);
+			dwc3_octeon_set_endian_mode((u64)base);
+			dwc3_octeon_phy_reset((u64)base);
+			dev_info(&pdev->dev, "clocks initialized.\n");
+			mutex_unlock(&dwc3_octeon_clocks_mutex);
+			devm_iounmap(&pdev->dev, base);
+			devm_release_mem_region(&pdev->dev, res->start,
+						resource_size(res));
+			put_device(&pdev->dev);
+		}
+	} while (node != NULL);
+
+	return 0;
+}
+device_initcall(dwc3_octeon_device_init);
+
+MODULE_AUTHOR("David Daney <david.daney@cavium.com>");
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("USB driver for OCTEON III SoC");
diff --git a/arch/mips/cavium-octeon/octeon_boot.h b/arch/mips/cavium-octeon/octeon_boot.h
new file mode 100644
index 000000000..9eab66f3b
--- /dev/null
+++ b/arch/mips/cavium-octeon/octeon_boot.h
@@ -0,0 +1,81 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * (C) Copyright 2004, 2005 Cavium Networks
+ */
+
+#ifndef __OCTEON_BOOT_H__
+#define __OCTEON_BOOT_H__
+
+#include <linux/types.h>
+
+struct boot_init_vector {
+	/* First stage address - in ram instead of flash */
+	uint64_t code_addr;
+	/* Setup code for application, NOT application entry point */
+	uint32_t app_start_func_addr;
+	/* k0 is used for global data - needs to be passed to other cores */
+	uint32_t k0_val;
+	/* Address of boot info block structure */
+	uint64_t boot_info_addr;
+	uint32_t flags;		/* flags */
+	uint32_t pad;
+};
+
+/* similar to bootloader's linux_app_boot_info but without global data */
+struct linux_app_boot_info {
+#ifdef __BIG_ENDIAN_BITFIELD
+	uint32_t labi_signature;
+	uint32_t start_core0_addr;
+	uint32_t avail_coremask;
+	uint32_t pci_console_active;
+	uint32_t icache_prefetch_disable;
+	uint32_t padding;
+	uint64_t InitTLBStart_addr;
+	uint32_t start_app_addr;
+	uint32_t cur_exception_base;
+	uint32_t no_mark_private_data;
+	uint32_t compact_flash_common_base_addr;
+	uint32_t compact_flash_attribute_base_addr;
+	uint32_t led_display_base_addr;
+#else
+	uint32_t start_core0_addr;
+	uint32_t labi_signature;
+
+	uint32_t pci_console_active;
+	uint32_t avail_coremask;
+
+	uint32_t padding;
+	uint32_t icache_prefetch_disable;
+
+	uint64_t InitTLBStart_addr;
+
+	uint32_t cur_exception_base;
+	uint32_t start_app_addr;
+
+	uint32_t compact_flash_common_base_addr;
+	uint32_t no_mark_private_data;
+
+	uint32_t led_display_base_addr;
+	uint32_t compact_flash_attribute_base_addr;
+#endif
+};
+
+/* If not to copy a lot of bootloader's structures
+   here is only offset of requested member */
+#define AVAIL_COREMASK_OFFSET_IN_LINUX_APP_BOOT_BLOCK	 0x765c
+
+/* hardcoded in bootloader */
+#define	 LABI_ADDR_IN_BOOTLOADER			 0x700
+
+#define LINUX_APP_BOOT_BLOCK_NAME "linux-app-boot"
+
+#define LABI_SIGNATURE 0xAABBCC01
+
+/*  from uboot-headers/octeon_mem_map.h */
+#define EXCEPTION_BASE_INCR	(4 * 1024)
+			       /* Increment size for exception base addresses (4k minimum) */
+#define EXCEPTION_BASE_BASE	0
+#define BOOTLOADER_PRIV_DATA_BASE	(EXCEPTION_BASE_BASE + 0x800)
+#define BOOTLOADER_BOOT_VECTOR		(BOOTLOADER_PRIV_DATA_BASE)
+
+#endif /* __OCTEON_BOOT_H__ */
diff --git a/arch/mips/cavium-octeon/setup.c b/arch/mips/cavium-octeon/setup.c
new file mode 100644
index 000000000..a71727f7a
--- /dev/null
+++ b/arch/mips/cavium-octeon/setup.c
@@ -0,0 +1,1258 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2004-2007 Cavium Networks
+ * Copyright (C) 2008, 2009 Wind River Systems
+ *   written by Ralf Baechle <ralf@linux-mips.org>
+ */
+#include <linux/compiler.h>
+#include <linux/vmalloc.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/console.h>
+#include <linux/delay.h>
+#include <linux/export.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/memblock.h>
+#include <linux/serial.h>
+#include <linux/smp.h>
+#include <linux/types.h>
+#include <linux/string.h>	/* for memset */
+#include <linux/tty.h>
+#include <linux/time.h>
+#include <linux/platform_device.h>
+#include <linux/serial_core.h>
+#include <linux/serial_8250.h>
+#include <linux/of_fdt.h>
+#include <linux/libfdt.h>
+#include <linux/kexec.h>
+
+#include <asm/processor.h>
+#include <asm/reboot.h>
+#include <asm/smp-ops.h>
+#include <asm/irq_cpu.h>
+#include <asm/mipsregs.h>
+#include <asm/bootinfo.h>
+#include <asm/sections.h>
+#include <asm/fw/fw.h>
+#include <asm/setup.h>
+#include <asm/prom.h>
+#include <asm/time.h>
+
+#include <asm/octeon/octeon.h>
+#include <asm/octeon/pci-octeon.h>
+#include <asm/octeon/cvmx-rst-defs.h>
+
+/*
+ * TRUE for devices having registers with little-endian byte
+ * order, FALSE for registers with native-endian byte order.
+ * PCI mandates little-endian, USB and SATA are configuraable,
+ * but we chose little-endian for these.
+ */
+const bool octeon_should_swizzle_table[256] = {
+	[0x00] = true,	/* bootbus/CF */
+	[0x1b] = true,	/* PCI mmio window */
+	[0x1c] = true,	/* PCI mmio window */
+	[0x1d] = true,	/* PCI mmio window */
+	[0x1e] = true,	/* PCI mmio window */
+	[0x68] = true,	/* OCTEON III USB */
+	[0x69] = true,	/* OCTEON III USB */
+	[0x6c] = true,	/* OCTEON III SATA */
+	[0x6f] = true,	/* OCTEON II USB */
+};
+EXPORT_SYMBOL(octeon_should_swizzle_table);
+
+#ifdef CONFIG_PCI
+extern void pci_console_init(const char *arg);
+#endif
+
+static unsigned long long max_memory = ULLONG_MAX;
+static unsigned long long reserve_low_mem;
+
+DEFINE_SEMAPHORE(octeon_bootbus_sem);
+EXPORT_SYMBOL(octeon_bootbus_sem);
+
+static struct octeon_boot_descriptor *octeon_boot_desc_ptr;
+
+struct cvmx_bootinfo *octeon_bootinfo;
+EXPORT_SYMBOL(octeon_bootinfo);
+
+#ifdef CONFIG_KEXEC
+#ifdef CONFIG_SMP
+/*
+ * Wait for relocation code is prepared and send
+ * secondary CPUs to spin until kernel is relocated.
+ */
+static void octeon_kexec_smp_down(void *ignored)
+{
+	int cpu = smp_processor_id();
+
+	local_irq_disable();
+	set_cpu_online(cpu, false);
+	while (!atomic_read(&kexec_ready_to_reboot))
+		cpu_relax();
+
+	asm volatile (
+	"	sync						\n"
+	"	synci	($0)					\n");
+
+	kexec_reboot();
+}
+#endif
+
+#define OCTEON_DDR0_BASE    (0x0ULL)
+#define OCTEON_DDR0_SIZE    (0x010000000ULL)
+#define OCTEON_DDR1_BASE    (0x410000000ULL)
+#define OCTEON_DDR1_SIZE    (0x010000000ULL)
+#define OCTEON_DDR2_BASE    (0x020000000ULL)
+#define OCTEON_DDR2_SIZE    (0x3e0000000ULL)
+#define OCTEON_MAX_PHY_MEM_SIZE (16*1024*1024*1024ULL)
+
+static struct kimage *kimage_ptr;
+
+static void kexec_bootmem_init(uint64_t mem_size, uint32_t low_reserved_bytes)
+{
+	int64_t addr;
+	struct cvmx_bootmem_desc *bootmem_desc;
+
+	bootmem_desc = cvmx_bootmem_get_desc();
+
+	if (mem_size > OCTEON_MAX_PHY_MEM_SIZE) {
+		mem_size = OCTEON_MAX_PHY_MEM_SIZE;
+		pr_err("Error: requested memory too large,"
+		       "truncating to maximum size\n");
+	}
+
+	bootmem_desc->major_version = CVMX_BOOTMEM_DESC_MAJ_VER;
+	bootmem_desc->minor_version = CVMX_BOOTMEM_DESC_MIN_VER;
+
+	addr = (OCTEON_DDR0_BASE + reserve_low_mem + low_reserved_bytes);
+	bootmem_desc->head_addr = 0;
+
+	if (mem_size <= OCTEON_DDR0_SIZE) {
+		__cvmx_bootmem_phy_free(addr,
+				mem_size - reserve_low_mem -
+				low_reserved_bytes, 0);
+		return;
+	}
+
+	__cvmx_bootmem_phy_free(addr,
+			OCTEON_DDR0_SIZE - reserve_low_mem -
+			low_reserved_bytes, 0);
+
+	mem_size -= OCTEON_DDR0_SIZE;
+
+	if (mem_size > OCTEON_DDR1_SIZE) {
+		__cvmx_bootmem_phy_free(OCTEON_DDR1_BASE, OCTEON_DDR1_SIZE, 0);
+		__cvmx_bootmem_phy_free(OCTEON_DDR2_BASE,
+				mem_size - OCTEON_DDR1_SIZE, 0);
+	} else
+		__cvmx_bootmem_phy_free(OCTEON_DDR1_BASE, mem_size, 0);
+}
+
+static int octeon_kexec_prepare(struct kimage *image)
+{
+	int i;
+	char *bootloader = "kexec";
+
+	octeon_boot_desc_ptr->argc = 0;
+	for (i = 0; i < image->nr_segments; i++) {
+		if (!strncmp(bootloader, (char *)image->segment[i].buf,
+				strlen(bootloader))) {
+			/*
+			 * convert command line string to array
+			 * of parameters (as bootloader does).
+			 */
+			int argc = 0, offt;
+			char *str = (char *)image->segment[i].buf;
+			char *ptr = strchr(str, ' ');
+			while (ptr && (OCTEON_ARGV_MAX_ARGS > argc)) {
+				*ptr = '\0';
+				if (ptr[1] != ' ') {
+					offt = (int)(ptr - str + 1);
+					octeon_boot_desc_ptr->argv[argc] =
+						image->segment[i].mem + offt;
+					argc++;
+				}
+				ptr = strchr(ptr + 1, ' ');
+			}
+			octeon_boot_desc_ptr->argc = argc;
+			break;
+		}
+	}
+
+	/*
+	 * Information about segments will be needed during pre-boot memory
+	 * initialization.
+	 */
+	kimage_ptr = image;
+	return 0;
+}
+
+static void octeon_generic_shutdown(void)
+{
+	int i;
+#ifdef CONFIG_SMP
+	int cpu;
+#endif
+	struct cvmx_bootmem_desc *bootmem_desc;
+	void *named_block_array_ptr;
+
+	bootmem_desc = cvmx_bootmem_get_desc();
+	named_block_array_ptr =
+		cvmx_phys_to_ptr(bootmem_desc->named_block_array_addr);
+
+#ifdef CONFIG_SMP
+	/* disable watchdogs */
+	for_each_online_cpu(cpu)
+		cvmx_write_csr(CVMX_CIU_WDOGX(cpu_logical_map(cpu)), 0);
+#else
+	cvmx_write_csr(CVMX_CIU_WDOGX(cvmx_get_core_num()), 0);
+#endif
+	if (kimage_ptr != kexec_crash_image) {
+		memset(named_block_array_ptr,
+			0x0,
+			CVMX_BOOTMEM_NUM_NAMED_BLOCKS *
+			sizeof(struct cvmx_bootmem_named_block_desc));
+		/*
+		 * Mark all memory (except low 0x100000 bytes) as free.
+		 * It is the same thing that bootloader does.
+		 */
+		kexec_bootmem_init(octeon_bootinfo->dram_size*1024ULL*1024ULL,
+				0x100000);
+		/*
+		 * Allocate all segments to avoid their corruption during boot.
+		 */
+		for (i = 0; i < kimage_ptr->nr_segments; i++)
+			cvmx_bootmem_alloc_address(
+				kimage_ptr->segment[i].memsz + 2*PAGE_SIZE,
+				kimage_ptr->segment[i].mem - PAGE_SIZE,
+				PAGE_SIZE);
+	} else {
+		/*
+		 * Do not mark all memory as free. Free only named sections
+		 * leaving the rest of memory unchanged.
+		 */
+		struct cvmx_bootmem_named_block_desc *ptr =
+			(struct cvmx_bootmem_named_block_desc *)
+			named_block_array_ptr;
+
+		for (i = 0; i < bootmem_desc->named_block_num_blocks; i++)
+			if (ptr[i].size)
+				cvmx_bootmem_free_named(ptr[i].name);
+	}
+	kexec_args[2] = 1UL; /* running on octeon_main_processor */
+	kexec_args[3] = (unsigned long)octeon_boot_desc_ptr;
+#ifdef CONFIG_SMP
+	secondary_kexec_args[2] = 0UL; /* running on secondary cpu */
+	secondary_kexec_args[3] = (unsigned long)octeon_boot_desc_ptr;
+#endif
+}
+
+static void octeon_shutdown(void)
+{
+	octeon_generic_shutdown();
+#ifdef CONFIG_SMP
+	smp_call_function(octeon_kexec_smp_down, NULL, 0);
+	smp_wmb();
+	while (num_online_cpus() > 1) {
+		cpu_relax();
+		mdelay(1);
+	}
+#endif
+}
+
+static void octeon_crash_shutdown(struct pt_regs *regs)
+{
+	octeon_generic_shutdown();
+	default_machine_crash_shutdown(regs);
+}
+
+#ifdef CONFIG_SMP
+void octeon_crash_smp_send_stop(void)
+{
+	int cpu;
+
+	/* disable watchdogs */
+	for_each_online_cpu(cpu)
+		cvmx_write_csr(CVMX_CIU_WDOGX(cpu_logical_map(cpu)), 0);
+}
+#endif
+
+#endif /* CONFIG_KEXEC */
+
+uint64_t octeon_reserve32_memory;
+EXPORT_SYMBOL(octeon_reserve32_memory);
+
+#ifdef CONFIG_KEXEC
+/* crashkernel cmdline parameter is parsed _after_ memory setup
+ * we also parse it here (workaround for EHB5200) */
+static uint64_t crashk_size, crashk_base;
+#endif
+
+static int octeon_uart;
+
+extern asmlinkage void handle_int(void);
+
+/**
+ * octeon_is_simulation - Return non-zero if we are currently running
+ * in the Octeon simulator
+ *
+ * Return: non-0 if running in the Octeon simulator, 0 otherwise
+ */
+int octeon_is_simulation(void)
+{
+	return octeon_bootinfo->board_type == CVMX_BOARD_TYPE_SIM;
+}
+EXPORT_SYMBOL(octeon_is_simulation);
+
+/**
+ * octeon_is_pci_host - Return true if Octeon is in PCI Host mode. This means
+ * Linux can control the PCI bus.
+ *
+ * Return: Non-zero if Octeon is in host mode.
+ */
+int octeon_is_pci_host(void)
+{
+#ifdef CONFIG_PCI
+	return octeon_bootinfo->config_flags & CVMX_BOOTINFO_CFG_FLAG_PCI_HOST;
+#else
+	return 0;
+#endif
+}
+
+/**
+ * octeon_get_clock_rate - Get the clock rate of Octeon
+ *
+ * Return: Clock rate in HZ
+ */
+uint64_t octeon_get_clock_rate(void)
+{
+	struct cvmx_sysinfo *sysinfo = cvmx_sysinfo_get();
+
+	return sysinfo->cpu_clock_hz;
+}
+EXPORT_SYMBOL(octeon_get_clock_rate);
+
+static u64 octeon_io_clock_rate;
+
+u64 octeon_get_io_clock_rate(void)
+{
+	return octeon_io_clock_rate;
+}
+EXPORT_SYMBOL(octeon_get_io_clock_rate);
+
+
+/**
+ * octeon_write_lcd - Write to the LCD display connected to the bootbus.
+ * @s:	    String to write
+ *
+ * This display exists on most Cavium evaluation boards. If it doesn't exist,
+ * then this function doesn't do anything.
+ */
+static void octeon_write_lcd(const char *s)
+{
+	if (octeon_bootinfo->led_display_base_addr) {
+		void __iomem *lcd_address =
+			ioremap(octeon_bootinfo->led_display_base_addr,
+					8);
+		int i;
+		for (i = 0; i < 8; i++, s++) {
+			if (*s)
+				iowrite8(*s, lcd_address + i);
+			else
+				iowrite8(' ', lcd_address + i);
+		}
+		iounmap(lcd_address);
+	}
+}
+
+/**
+ * octeon_get_boot_uart - Return the console uart passed by the bootloader
+ *
+ * Return: uart number (0 or 1)
+ */
+static int octeon_get_boot_uart(void)
+{
+	return (octeon_boot_desc_ptr->flags & OCTEON_BL_FLAG_CONSOLE_UART1) ?
+		1 : 0;
+}
+
+/**
+ * octeon_get_boot_coremask - Get the coremask Linux was booted on.
+ *
+ * Return: Core mask
+ */
+int octeon_get_boot_coremask(void)
+{
+	return octeon_boot_desc_ptr->core_mask;
+}
+
+/**
+ * octeon_check_cpu_bist - Check the hardware BIST results for a CPU
+ */
+void octeon_check_cpu_bist(void)
+{
+	const int coreid = cvmx_get_core_num();
+	unsigned long long mask;
+	unsigned long long bist_val;
+
+	/* Check BIST results for COP0 registers */
+	mask = 0x1f00000000ull;
+	bist_val = read_octeon_c0_icacheerr();
+	if (bist_val & mask)
+		pr_err("Core%d BIST Failure: CacheErr(icache) = 0x%llx\n",
+		       coreid, bist_val);
+
+	bist_val = read_octeon_c0_dcacheerr();
+	if (bist_val & 1)
+		pr_err("Core%d L1 Dcache parity error: "
+		       "CacheErr(dcache) = 0x%llx\n",
+		       coreid, bist_val);
+
+	mask = 0xfc00000000000000ull;
+	bist_val = read_c0_cvmmemctl();
+	if (bist_val & mask)
+		pr_err("Core%d BIST Failure: COP0_CVM_MEM_CTL = 0x%llx\n",
+		       coreid, bist_val);
+
+	write_octeon_c0_dcacheerr(0);
+}
+
+/**
+ * octeon_restart - Reboot Octeon
+ *
+ * @command: Command to pass to the bootloader. Currently ignored.
+ */
+static void octeon_restart(char *command)
+{
+	/* Disable all watchdogs before soft reset. They don't get cleared */
+#ifdef CONFIG_SMP
+	int cpu;
+	for_each_online_cpu(cpu)
+		cvmx_write_csr(CVMX_CIU_WDOGX(cpu_logical_map(cpu)), 0);
+#else
+	cvmx_write_csr(CVMX_CIU_WDOGX(cvmx_get_core_num()), 0);
+#endif
+
+	mb();
+	while (1)
+		if (OCTEON_IS_OCTEON3())
+			cvmx_write_csr(CVMX_RST_SOFT_RST, 1);
+		else
+			cvmx_write_csr(CVMX_CIU_SOFT_RST, 1);
+}
+
+
+/**
+ * octeon_kill_core - Permanently stop a core.
+ *
+ * @arg: Ignored.
+ */
+static void octeon_kill_core(void *arg)
+{
+	if (octeon_is_simulation())
+		/* A break instruction causes the simulator stop a core */
+		asm volatile ("break" ::: "memory");
+
+	local_irq_disable();
+	/* Disable watchdog on this core. */
+	cvmx_write_csr(CVMX_CIU_WDOGX(cvmx_get_core_num()), 0);
+	/* Spin in a low power mode. */
+	while (true)
+		asm volatile ("wait" ::: "memory");
+}
+
+
+/**
+ * octeon_halt - Halt the system
+ */
+static void octeon_halt(void)
+{
+	smp_call_function(octeon_kill_core, NULL, 0);
+
+	switch (octeon_bootinfo->board_type) {
+	case CVMX_BOARD_TYPE_NAO38:
+		/* Driving a 1 to GPIO 12 shuts off this board */
+		cvmx_write_csr(CVMX_GPIO_BIT_CFGX(12), 1);
+		cvmx_write_csr(CVMX_GPIO_TX_SET, 0x1000);
+		break;
+	default:
+		octeon_write_lcd("PowerOff");
+		break;
+	}
+
+	octeon_kill_core(NULL);
+}
+
+static char __read_mostly octeon_system_type[80];
+
+static void __init init_octeon_system_type(void)
+{
+	char const *board_type;
+
+	board_type = cvmx_board_type_to_string(octeon_bootinfo->board_type);
+	if (board_type == NULL) {
+		struct device_node *root;
+		int ret;
+
+		root = of_find_node_by_path("/");
+		ret = of_property_read_string(root, "model", &board_type);
+		of_node_put(root);
+		if (ret)
+			board_type = "Unsupported Board";
+	}
+
+	snprintf(octeon_system_type, sizeof(octeon_system_type), "%s (%s)",
+		 board_type, octeon_model_get_string(read_c0_prid()));
+}
+
+/**
+ * octeon_board_type_string - Return a string representing the system type
+ *
+ * Return: system type string
+ */
+const char *octeon_board_type_string(void)
+{
+	return octeon_system_type;
+}
+
+const char *get_system_type(void)
+	__attribute__ ((alias("octeon_board_type_string")));
+
+void octeon_user_io_init(void)
+{
+	union octeon_cvmemctl cvmmemctl;
+
+	/* Get the current settings for CP0_CVMMEMCTL_REG */
+	cvmmemctl.u64 = read_c0_cvmmemctl();
+	/* R/W If set, marked write-buffer entries time out the same
+	 * as other entries; if clear, marked write-buffer entries
+	 * use the maximum timeout. */
+	cvmmemctl.s.dismarkwblongto = 1;
+	/* R/W If set, a merged store does not clear the write-buffer
+	 * entry timeout state. */
+	cvmmemctl.s.dismrgclrwbto = 0;
+	/* R/W Two bits that are the MSBs of the resultant CVMSEG LM
+	 * word location for an IOBDMA. The other 8 bits come from the
+	 * SCRADDR field of the IOBDMA. */
+	cvmmemctl.s.iobdmascrmsb = 0;
+	/* R/W If set, SYNCWS and SYNCS only order marked stores; if
+	 * clear, SYNCWS and SYNCS only order unmarked
+	 * stores. SYNCWSMARKED has no effect when DISSYNCWS is
+	 * set. */
+	cvmmemctl.s.syncwsmarked = 0;
+	/* R/W If set, SYNCWS acts as SYNCW and SYNCS acts as SYNC. */
+	cvmmemctl.s.dissyncws = 0;
+	/* R/W If set, no stall happens on write buffer full. */
+	if (OCTEON_IS_MODEL(OCTEON_CN38XX_PASS2))
+		cvmmemctl.s.diswbfst = 1;
+	else
+		cvmmemctl.s.diswbfst = 0;
+	/* R/W If set (and SX set), supervisor-level loads/stores can
+	 * use XKPHYS addresses with <48>==0 */
+	cvmmemctl.s.xkmemenas = 0;
+
+	/* R/W If set (and UX set), user-level loads/stores can use
+	 * XKPHYS addresses with VA<48>==0 */
+	cvmmemctl.s.xkmemenau = 0;
+
+	/* R/W If set (and SX set), supervisor-level loads/stores can
+	 * use XKPHYS addresses with VA<48>==1 */
+	cvmmemctl.s.xkioenas = 0;
+
+	/* R/W If set (and UX set), user-level loads/stores can use
+	 * XKPHYS addresses with VA<48>==1 */
+	cvmmemctl.s.xkioenau = 0;
+
+	/* R/W If set, all stores act as SYNCW (NOMERGE must be set
+	 * when this is set) RW, reset to 0. */
+	cvmmemctl.s.allsyncw = 0;
+
+	/* R/W If set, no stores merge, and all stores reach the
+	 * coherent bus in order. */
+	cvmmemctl.s.nomerge = 0;
+	/* R/W Selects the bit in the counter used for DID time-outs 0
+	 * = 231, 1 = 230, 2 = 229, 3 = 214. Actual time-out is
+	 * between 1x and 2x this interval. For example, with
+	 * DIDTTO=3, expiration interval is between 16K and 32K. */
+	cvmmemctl.s.didtto = 0;
+	/* R/W If set, the (mem) CSR clock never turns off. */
+	cvmmemctl.s.csrckalwys = 0;
+	/* R/W If set, mclk never turns off. */
+	cvmmemctl.s.mclkalwys = 0;
+	/* R/W Selects the bit in the counter used for write buffer
+	 * flush time-outs (WBFLT+11) is the bit position in an
+	 * internal counter used to determine expiration. The write
+	 * buffer expires between 1x and 2x this interval. For
+	 * example, with WBFLT = 0, a write buffer expires between 2K
+	 * and 4K cycles after the write buffer entry is allocated. */
+	cvmmemctl.s.wbfltime = 0;
+	/* R/W If set, do not put Istream in the L2 cache. */
+	cvmmemctl.s.istrnol2 = 0;
+
+	/*
+	 * R/W The write buffer threshold. As per erratum Core-14752
+	 * for CN63XX, a sc/scd might fail if the write buffer is
+	 * full.  Lowering WBTHRESH greatly lowers the chances of the
+	 * write buffer ever being full and triggering the erratum.
+	 */
+	if (OCTEON_IS_MODEL(OCTEON_CN63XX_PASS1_X))
+		cvmmemctl.s.wbthresh = 4;
+	else
+		cvmmemctl.s.wbthresh = 10;
+
+	/* R/W If set, CVMSEG is available for loads/stores in
+	 * kernel/debug mode. */
+#if CONFIG_CAVIUM_OCTEON_CVMSEG_SIZE > 0
+	cvmmemctl.s.cvmsegenak = 1;
+#else
+	cvmmemctl.s.cvmsegenak = 0;
+#endif
+	/* R/W If set, CVMSEG is available for loads/stores in
+	 * supervisor mode. */
+	cvmmemctl.s.cvmsegenas = 0;
+	/* R/W If set, CVMSEG is available for loads/stores in user
+	 * mode. */
+	cvmmemctl.s.cvmsegenau = 0;
+
+	write_c0_cvmmemctl(cvmmemctl.u64);
+
+	/* Setup of CVMSEG is done in kernel-entry-init.h */
+	if (smp_processor_id() == 0)
+		pr_notice("CVMSEG size: %d cache lines (%d bytes)\n",
+			  CONFIG_CAVIUM_OCTEON_CVMSEG_SIZE,
+			  CONFIG_CAVIUM_OCTEON_CVMSEG_SIZE * 128);
+
+	if (octeon_has_feature(OCTEON_FEATURE_FAU)) {
+		union cvmx_iob_fau_timeout fau_timeout;
+
+		/* Set a default for the hardware timeouts */
+		fau_timeout.u64 = 0;
+		fau_timeout.s.tout_val = 0xfff;
+		/* Disable tagwait FAU timeout */
+		fau_timeout.s.tout_enb = 0;
+		cvmx_write_csr(CVMX_IOB_FAU_TIMEOUT, fau_timeout.u64);
+	}
+
+	if ((!OCTEON_IS_MODEL(OCTEON_CN68XX) &&
+	     !OCTEON_IS_MODEL(OCTEON_CN7XXX)) ||
+	    OCTEON_IS_MODEL(OCTEON_CN70XX)) {
+		union cvmx_pow_nw_tim nm_tim;
+
+		nm_tim.u64 = 0;
+		/* 4096 cycles */
+		nm_tim.s.nw_tim = 3;
+		cvmx_write_csr(CVMX_POW_NW_TIM, nm_tim.u64);
+	}
+
+	write_octeon_c0_icacheerr(0);
+	write_c0_derraddr1(0);
+}
+
+/**
+ * prom_init - Early entry point for arch setup
+ */
+void __init prom_init(void)
+{
+	struct cvmx_sysinfo *sysinfo;
+	const char *arg;
+	char *p;
+	int i;
+	u64 t;
+	int argc;
+	/*
+	 * The bootloader passes a pointer to the boot descriptor in
+	 * $a3, this is available as fw_arg3.
+	 */
+	octeon_boot_desc_ptr = (struct octeon_boot_descriptor *)fw_arg3;
+	octeon_bootinfo =
+		cvmx_phys_to_ptr(octeon_boot_desc_ptr->cvmx_desc_vaddr);
+	cvmx_bootmem_init(cvmx_phys_to_ptr(octeon_bootinfo->phy_mem_desc_addr));
+
+	sysinfo = cvmx_sysinfo_get();
+	memset(sysinfo, 0, sizeof(*sysinfo));
+	sysinfo->system_dram_size = octeon_bootinfo->dram_size << 20;
+	sysinfo->phy_mem_desc_addr = (u64)phys_to_virt(octeon_bootinfo->phy_mem_desc_addr);
+
+	if ((octeon_bootinfo->major_version > 1) ||
+	    (octeon_bootinfo->major_version == 1 &&
+	     octeon_bootinfo->minor_version >= 4))
+		cvmx_coremask_copy(&sysinfo->core_mask,
+				   &octeon_bootinfo->ext_core_mask);
+	else
+		cvmx_coremask_set64(&sysinfo->core_mask,
+				    octeon_bootinfo->core_mask);
+
+	/* Some broken u-boot pass garbage in upper bits, clear them out */
+	if (!OCTEON_IS_MODEL(OCTEON_CN78XX))
+		for (i = 512; i < 1024; i++)
+			cvmx_coremask_clear_core(&sysinfo->core_mask, i);
+
+	sysinfo->exception_base_addr = octeon_bootinfo->exception_base_addr;
+	sysinfo->cpu_clock_hz = octeon_bootinfo->eclock_hz;
+	sysinfo->dram_data_rate_hz = octeon_bootinfo->dclock_hz * 2;
+	sysinfo->board_type = octeon_bootinfo->board_type;
+	sysinfo->board_rev_major = octeon_bootinfo->board_rev_major;
+	sysinfo->board_rev_minor = octeon_bootinfo->board_rev_minor;
+	memcpy(sysinfo->mac_addr_base, octeon_bootinfo->mac_addr_base,
+	       sizeof(sysinfo->mac_addr_base));
+	sysinfo->mac_addr_count = octeon_bootinfo->mac_addr_count;
+	memcpy(sysinfo->board_serial_number,
+	       octeon_bootinfo->board_serial_number,
+	       sizeof(sysinfo->board_serial_number));
+	sysinfo->compact_flash_common_base_addr =
+		octeon_bootinfo->compact_flash_common_base_addr;
+	sysinfo->compact_flash_attribute_base_addr =
+		octeon_bootinfo->compact_flash_attribute_base_addr;
+	sysinfo->led_display_base_addr = octeon_bootinfo->led_display_base_addr;
+	sysinfo->dfa_ref_clock_hz = octeon_bootinfo->dfa_ref_clock_hz;
+	sysinfo->bootloader_config_flags = octeon_bootinfo->config_flags;
+
+	if (OCTEON_IS_OCTEON2()) {
+		/* I/O clock runs at a different rate than the CPU. */
+		union cvmx_mio_rst_boot rst_boot;
+		rst_boot.u64 = cvmx_read_csr(CVMX_MIO_RST_BOOT);
+		octeon_io_clock_rate = 50000000 * rst_boot.s.pnr_mul;
+	} else if (OCTEON_IS_OCTEON3()) {
+		/* I/O clock runs at a different rate than the CPU. */
+		union cvmx_rst_boot rst_boot;
+		rst_boot.u64 = cvmx_read_csr(CVMX_RST_BOOT);
+		octeon_io_clock_rate = 50000000 * rst_boot.s.pnr_mul;
+	} else {
+		octeon_io_clock_rate = sysinfo->cpu_clock_hz;
+	}
+
+	t = read_c0_cvmctl();
+	if ((t & (1ull << 27)) == 0) {
+		/*
+		 * Setup the multiplier save/restore code if
+		 * CvmCtl[NOMUL] clear.
+		 */
+		void *save;
+		void *save_end;
+		void *restore;
+		void *restore_end;
+		int save_len;
+		int restore_len;
+		int save_max = (char *)octeon_mult_save_end -
+			(char *)octeon_mult_save;
+		int restore_max = (char *)octeon_mult_restore_end -
+			(char *)octeon_mult_restore;
+		if (current_cpu_data.cputype == CPU_CAVIUM_OCTEON3) {
+			save = octeon_mult_save3;
+			save_end = octeon_mult_save3_end;
+			restore = octeon_mult_restore3;
+			restore_end = octeon_mult_restore3_end;
+		} else {
+			save = octeon_mult_save2;
+			save_end = octeon_mult_save2_end;
+			restore = octeon_mult_restore2;
+			restore_end = octeon_mult_restore2_end;
+		}
+		save_len = (char *)save_end - (char *)save;
+		restore_len = (char *)restore_end - (char *)restore;
+		if (!WARN_ON(save_len > save_max ||
+				restore_len > restore_max)) {
+			memcpy(octeon_mult_save, save, save_len);
+			memcpy(octeon_mult_restore, restore, restore_len);
+		}
+	}
+
+	/*
+	 * Only enable the LED controller if we're running on a CN38XX, CN58XX,
+	 * or CN56XX. The CN30XX and CN31XX don't have an LED controller.
+	 */
+	if (!octeon_is_simulation() &&
+	    octeon_has_feature(OCTEON_FEATURE_LED_CONTROLLER)) {
+		cvmx_write_csr(CVMX_LED_EN, 0);
+		cvmx_write_csr(CVMX_LED_PRT, 0);
+		cvmx_write_csr(CVMX_LED_DBG, 0);
+		cvmx_write_csr(CVMX_LED_PRT_FMT, 0);
+		cvmx_write_csr(CVMX_LED_UDD_CNTX(0), 32);
+		cvmx_write_csr(CVMX_LED_UDD_CNTX(1), 32);
+		cvmx_write_csr(CVMX_LED_UDD_DATX(0), 0);
+		cvmx_write_csr(CVMX_LED_UDD_DATX(1), 0);
+		cvmx_write_csr(CVMX_LED_EN, 1);
+	}
+
+	/*
+	 * We need to temporarily allocate all memory in the reserve32
+	 * region. This makes sure the kernel doesn't allocate this
+	 * memory when it is getting memory from the
+	 * bootloader. Later, after the memory allocations are
+	 * complete, the reserve32 will be freed.
+	 *
+	 * Allocate memory for RESERVED32 aligned on 2MB boundary. This
+	 * is in case we later use hugetlb entries with it.
+	 */
+	if (CONFIG_CAVIUM_RESERVE32) {
+		int64_t addr =
+			cvmx_bootmem_phy_named_block_alloc(CONFIG_CAVIUM_RESERVE32 << 20,
+							   0, 0, 2 << 20,
+							   "CAVIUM_RESERVE32", 0);
+		if (addr < 0)
+			pr_err("Failed to allocate CAVIUM_RESERVE32 memory area\n");
+		else
+			octeon_reserve32_memory = addr;
+	}
+
+#ifdef CONFIG_CAVIUM_OCTEON_LOCK_L2
+	if (cvmx_read_csr(CVMX_L2D_FUS3) & (3ull << 34)) {
+		pr_info("Skipping L2 locking due to reduced L2 cache size\n");
+	} else {
+		uint32_t __maybe_unused ebase = read_c0_ebase() & 0x3ffff000;
+#ifdef CONFIG_CAVIUM_OCTEON_LOCK_L2_TLB
+		/* TLB refill */
+		cvmx_l2c_lock_mem_region(ebase, 0x100);
+#endif
+#ifdef CONFIG_CAVIUM_OCTEON_LOCK_L2_EXCEPTION
+		/* General exception */
+		cvmx_l2c_lock_mem_region(ebase + 0x180, 0x80);
+#endif
+#ifdef CONFIG_CAVIUM_OCTEON_LOCK_L2_LOW_LEVEL_INTERRUPT
+		/* Interrupt handler */
+		cvmx_l2c_lock_mem_region(ebase + 0x200, 0x80);
+#endif
+#ifdef CONFIG_CAVIUM_OCTEON_LOCK_L2_INTERRUPT
+		cvmx_l2c_lock_mem_region(__pa_symbol(handle_int), 0x100);
+		cvmx_l2c_lock_mem_region(__pa_symbol(plat_irq_dispatch), 0x80);
+#endif
+#ifdef CONFIG_CAVIUM_OCTEON_LOCK_L2_MEMCPY
+		cvmx_l2c_lock_mem_region(__pa_symbol(memcpy), 0x480);
+#endif
+	}
+#endif
+
+	octeon_check_cpu_bist();
+
+	octeon_uart = octeon_get_boot_uart();
+
+#ifdef CONFIG_SMP
+	octeon_write_lcd("LinuxSMP");
+#else
+	octeon_write_lcd("Linux");
+#endif
+
+	octeon_setup_delays();
+
+	/*
+	 * BIST should always be enabled when doing a soft reset. L2
+	 * Cache locking for instance is not cleared unless BIST is
+	 * enabled.  Unfortunately due to a chip errata G-200 for
+	 * Cn38XX and CN31XX, BIST must be disabled on these parts.
+	 */
+	if (OCTEON_IS_MODEL(OCTEON_CN38XX_PASS2) ||
+	    OCTEON_IS_MODEL(OCTEON_CN31XX))
+		cvmx_write_csr(CVMX_CIU_SOFT_BIST, 0);
+	else
+		cvmx_write_csr(CVMX_CIU_SOFT_BIST, 1);
+
+	/* Default to 64MB in the simulator to speed things up */
+	if (octeon_is_simulation())
+		max_memory = 64ull << 20;
+
+	arg = strstr(arcs_cmdline, "mem=");
+	if (arg) {
+		max_memory = memparse(arg + 4, &p);
+		if (max_memory == 0)
+			max_memory = 32ull << 30;
+		if (*p == '@')
+			reserve_low_mem = memparse(p + 1, &p);
+	}
+
+	arcs_cmdline[0] = 0;
+	argc = octeon_boot_desc_ptr->argc;
+	for (i = 0; i < argc; i++) {
+		const char *arg =
+			cvmx_phys_to_ptr(octeon_boot_desc_ptr->argv[i]);
+		if ((strncmp(arg, "MEM=", 4) == 0) ||
+		    (strncmp(arg, "mem=", 4) == 0)) {
+			max_memory = memparse(arg + 4, &p);
+			if (max_memory == 0)
+				max_memory = 32ull << 30;
+			if (*p == '@')
+				reserve_low_mem = memparse(p + 1, &p);
+#ifdef CONFIG_KEXEC
+		} else if (strncmp(arg, "crashkernel=", 12) == 0) {
+			crashk_size = memparse(arg+12, &p);
+			if (*p == '@')
+				crashk_base = memparse(p+1, &p);
+			strcat(arcs_cmdline, " ");
+			strcat(arcs_cmdline, arg);
+			/*
+			 * To do: switch parsing to new style, something like:
+			 * parse_crashkernel(arg, sysinfo->system_dram_size,
+			 *		  &crashk_size, &crashk_base);
+			 */
+#endif
+		} else if (strlen(arcs_cmdline) + strlen(arg) + 1 <
+			   sizeof(arcs_cmdline) - 1) {
+			strcat(arcs_cmdline, " ");
+			strcat(arcs_cmdline, arg);
+		}
+	}
+
+	if (strstr(arcs_cmdline, "console=") == NULL) {
+		if (octeon_uart == 1)
+			strcat(arcs_cmdline, " console=ttyS1,115200");
+		else
+			strcat(arcs_cmdline, " console=ttyS0,115200");
+	}
+
+	mips_hpt_frequency = octeon_get_clock_rate();
+
+	octeon_init_cvmcount();
+
+	_machine_restart = octeon_restart;
+	_machine_halt = octeon_halt;
+
+#ifdef CONFIG_KEXEC
+	_machine_kexec_shutdown = octeon_shutdown;
+	_machine_crash_shutdown = octeon_crash_shutdown;
+	_machine_kexec_prepare = octeon_kexec_prepare;
+#ifdef CONFIG_SMP
+	_crash_smp_send_stop = octeon_crash_smp_send_stop;
+#endif
+#endif
+
+	octeon_user_io_init();
+	octeon_setup_smp();
+}
+
+/* Exclude a single page from the regions obtained in plat_mem_setup. */
+#ifndef CONFIG_CRASH_DUMP
+static __init void memory_exclude_page(u64 addr, u64 *mem, u64 *size)
+{
+	if (addr > *mem && addr < *mem + *size) {
+		u64 inc = addr - *mem;
+		memblock_add(*mem, inc);
+		*mem += inc;
+		*size -= inc;
+	}
+
+	if (addr == *mem && *size > PAGE_SIZE) {
+		*mem += PAGE_SIZE;
+		*size -= PAGE_SIZE;
+	}
+}
+#endif /* CONFIG_CRASH_DUMP */
+
+void __init fw_init_cmdline(void)
+{
+	int i;
+
+	octeon_boot_desc_ptr = (struct octeon_boot_descriptor *)fw_arg3;
+	for (i = 0; i < octeon_boot_desc_ptr->argc; i++) {
+		const char *arg =
+			cvmx_phys_to_ptr(octeon_boot_desc_ptr->argv[i]);
+		if (strlen(arcs_cmdline) + strlen(arg) + 1 <
+			   sizeof(arcs_cmdline) - 1) {
+			strcat(arcs_cmdline, " ");
+			strcat(arcs_cmdline, arg);
+		}
+	}
+}
+
+void __init *plat_get_fdt(void)
+{
+	octeon_bootinfo =
+		cvmx_phys_to_ptr(octeon_boot_desc_ptr->cvmx_desc_vaddr);
+	return phys_to_virt(octeon_bootinfo->fdt_addr);
+}
+
+void __init plat_mem_setup(void)
+{
+	uint64_t mem_alloc_size;
+	uint64_t total;
+	uint64_t crashk_end;
+#ifndef CONFIG_CRASH_DUMP
+	int64_t memory;
+#endif
+
+	total = 0;
+	crashk_end = 0;
+
+	/*
+	 * The Mips memory init uses the first memory location for
+	 * some memory vectors. When SPARSEMEM is in use, it doesn't
+	 * verify that the size is big enough for the final
+	 * vectors. Making the smallest chuck 4MB seems to be enough
+	 * to consistently work.
+	 */
+	mem_alloc_size = 4 << 20;
+	if (mem_alloc_size > max_memory)
+		mem_alloc_size = max_memory;
+
+/* Crashkernel ignores bootmem list. It relies on mem=X@Y option */
+#ifdef CONFIG_CRASH_DUMP
+	memblock_add(reserve_low_mem, max_memory);
+	total += max_memory;
+#else
+#ifdef CONFIG_KEXEC
+	if (crashk_size > 0) {
+		memblock_add(crashk_base, crashk_size);
+		crashk_end = crashk_base + crashk_size;
+	}
+#endif
+	/*
+	 * When allocating memory, we want incrementing addresses,
+	 * which is handled by memblock
+	 */
+	cvmx_bootmem_lock();
+	while (total < max_memory) {
+		memory = cvmx_bootmem_phy_alloc(mem_alloc_size,
+						__pa_symbol(&_end), -1,
+						0x100000,
+						CVMX_BOOTMEM_FLAG_NO_LOCKING);
+		if (memory >= 0) {
+			u64 size = mem_alloc_size;
+#ifdef CONFIG_KEXEC
+			uint64_t end;
+#endif
+
+			/*
+			 * exclude a page at the beginning and end of
+			 * the 256MB PCIe 'hole' so the kernel will not
+			 * try to allocate multi-page buffers that
+			 * span the discontinuity.
+			 */
+			memory_exclude_page(CVMX_PCIE_BAR1_PHYS_BASE,
+					    &memory, &size);
+			memory_exclude_page(CVMX_PCIE_BAR1_PHYS_BASE +
+					    CVMX_PCIE_BAR1_PHYS_SIZE,
+					    &memory, &size);
+#ifdef CONFIG_KEXEC
+			end = memory + mem_alloc_size;
+
+			/*
+			 * This function automatically merges address regions
+			 * next to each other if they are received in
+			 * incrementing order
+			 */
+			if (memory < crashk_base && end >  crashk_end) {
+				/* region is fully in */
+				memblock_add(memory, crashk_base - memory);
+				total += crashk_base - memory;
+				memblock_add(crashk_end, end - crashk_end);
+				total += end - crashk_end;
+				continue;
+			}
+
+			if (memory >= crashk_base && end <= crashk_end)
+				/*
+				 * Entire memory region is within the new
+				 *  kernel's memory, ignore it.
+				 */
+				continue;
+
+			if (memory > crashk_base && memory < crashk_end &&
+			    end > crashk_end) {
+				/*
+				 * Overlap with the beginning of the region,
+				 * reserve the beginning.
+				  */
+				mem_alloc_size -= crashk_end - memory;
+				memory = crashk_end;
+			} else if (memory < crashk_base && end > crashk_base &&
+				   end < crashk_end)
+				/*
+				 * Overlap with the beginning of the region,
+				 * chop of end.
+				 */
+				mem_alloc_size -= end - crashk_base;
+#endif
+			memblock_add(memory, mem_alloc_size);
+			total += mem_alloc_size;
+			/* Recovering mem_alloc_size */
+			mem_alloc_size = 4 << 20;
+		} else {
+			break;
+		}
+	}
+	cvmx_bootmem_unlock();
+#endif /* CONFIG_CRASH_DUMP */
+
+	/*
+	 * Now that we've allocated the kernel memory it is safe to
+	 * free the reserved region. We free it here so that builtin
+	 * drivers can use the memory.
+	 */
+	if (octeon_reserve32_memory)
+		cvmx_bootmem_free_named("CAVIUM_RESERVE32");
+
+	if (total == 0)
+		panic("Unable to allocate memory from "
+		      "cvmx_bootmem_phy_alloc");
+}
+
+/*
+ * Emit one character to the boot UART.	 Exported for use by the
+ * watchdog timer.
+ */
+void prom_putchar(char c)
+{
+	uint64_t lsrval;
+
+	/* Spin until there is room */
+	do {
+		lsrval = cvmx_read_csr(CVMX_MIO_UARTX_LSR(octeon_uart));
+	} while ((lsrval & 0x20) == 0);
+
+	/* Write the byte */
+	cvmx_write_csr(CVMX_MIO_UARTX_THR(octeon_uart), c & 0xffull);
+}
+EXPORT_SYMBOL(prom_putchar);
+
+void __init prom_free_prom_memory(void)
+{
+	if (OCTEON_IS_MODEL(OCTEON_CN6XXX)) {
+		/* Check for presence of Core-14449 fix.  */
+		u32 insn;
+		u32 *foo;
+
+		foo = &insn;
+
+		asm volatile("# before" : : : "memory");
+		prefetch(foo);
+		asm volatile(
+			".set push\n\t"
+			".set noreorder\n\t"
+			"bal 1f\n\t"
+			"nop\n"
+			"1:\tlw %0,-12($31)\n\t"
+			".set pop\n\t"
+			: "=r" (insn) : : "$31", "memory");
+
+		if ((insn >> 26) != 0x33)
+			panic("No PREF instruction at Core-14449 probe point.");
+
+		if (((insn >> 16) & 0x1f) != 28)
+			panic("OCTEON II DCache prefetch workaround not in place (%04x).\n"
+			      "Please build kernel with proper options (CONFIG_CAVIUM_CN63XXP1).",
+			      insn);
+	}
+}
+
+void __init octeon_fill_mac_addresses(void);
+
+void __init device_tree_init(void)
+{
+	const void *fdt;
+	bool do_prune;
+	bool fill_mac;
+
+#ifdef CONFIG_MIPS_ELF_APPENDED_DTB
+	if (!fdt_check_header(&__appended_dtb)) {
+		fdt = &__appended_dtb;
+		do_prune = false;
+		fill_mac = true;
+		pr_info("Using appended Device Tree.\n");
+	} else
+#endif
+	if (octeon_bootinfo->minor_version >= 3 && octeon_bootinfo->fdt_addr) {
+		fdt = phys_to_virt(octeon_bootinfo->fdt_addr);
+		if (fdt_check_header(fdt))
+			panic("Corrupt Device Tree passed to kernel.");
+		do_prune = false;
+		fill_mac = false;
+		pr_info("Using passed Device Tree.\n");
+	} else if (OCTEON_IS_MODEL(OCTEON_CN68XX)) {
+		fdt = &__dtb_octeon_68xx_begin;
+		do_prune = true;
+		fill_mac = true;
+	} else {
+		fdt = &__dtb_octeon_3xxx_begin;
+		do_prune = true;
+		fill_mac = true;
+	}
+
+	initial_boot_params = (void *)fdt;
+
+	if (do_prune) {
+		octeon_prune_device_tree();
+		pr_info("Using internal Device Tree.\n");
+	}
+	if (fill_mac)
+		octeon_fill_mac_addresses();
+	unflatten_and_copy_device_tree();
+	init_octeon_system_type();
+}
+
+static int __initdata disable_octeon_edac_p;
+
+static int __init disable_octeon_edac(char *str)
+{
+	disable_octeon_edac_p = 1;
+	return 0;
+}
+early_param("disable_octeon_edac", disable_octeon_edac);
+
+static char *edac_device_names[] = {
+	"octeon_l2c_edac",
+	"octeon_pc_edac",
+};
+
+static int __init edac_devinit(void)
+{
+	struct platform_device *dev;
+	int i, err = 0;
+	int num_lmc;
+	char *name;
+
+	if (disable_octeon_edac_p)
+		return 0;
+
+	for (i = 0; i < ARRAY_SIZE(edac_device_names); i++) {
+		name = edac_device_names[i];
+		dev = platform_device_register_simple(name, -1, NULL, 0);
+		if (IS_ERR(dev)) {
+			pr_err("Registration of %s failed!\n", name);
+			err = PTR_ERR(dev);
+		}
+	}
+
+	num_lmc = OCTEON_IS_MODEL(OCTEON_CN68XX) ? 4 :
+		(OCTEON_IS_MODEL(OCTEON_CN56XX) ? 2 : 1);
+	for (i = 0; i < num_lmc; i++) {
+		dev = platform_device_register_simple("octeon_lmc_edac",
+						      i, NULL, 0);
+		if (IS_ERR(dev)) {
+			pr_err("Registration of octeon_lmc_edac %d failed!\n", i);
+			err = PTR_ERR(dev);
+		}
+	}
+
+	return err;
+}
+device_initcall(edac_devinit);
+
+static void __initdata *octeon_dummy_iospace;
+
+static int __init octeon_no_pci_init(void)
+{
+	/*
+	 * Initially assume there is no PCI. The PCI/PCIe platform code will
+	 * later re-initialize these to correct values if they are present.
+	 */
+	octeon_dummy_iospace = vzalloc(IO_SPACE_LIMIT);
+	set_io_port_base((unsigned long)octeon_dummy_iospace);
+	ioport_resource.start = MAX_RESOURCE;
+	ioport_resource.end = 0;
+	return 0;
+}
+core_initcall(octeon_no_pci_init);
+
+static int __init octeon_no_pci_release(void)
+{
+	/*
+	 * Release the allocated memory if a real IO space is there.
+	 */
+	if ((unsigned long)octeon_dummy_iospace != mips_io_port_base)
+		vfree(octeon_dummy_iospace);
+	return 0;
+}
+late_initcall(octeon_no_pci_release);
diff --git a/arch/mips/cavium-octeon/smp.c b/arch/mips/cavium-octeon/smp.c
new file mode 100644
index 000000000..89954f5f8
--- /dev/null
+++ b/arch/mips/cavium-octeon/smp.c
@@ -0,0 +1,518 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2004-2008, 2009, 2010 Cavium Networks
+ */
+#include <linux/cpu.h>
+#include <linux/delay.h>
+#include <linux/smp.h>
+#include <linux/interrupt.h>
+#include <linux/kernel_stat.h>
+#include <linux/sched.h>
+#include <linux/sched/hotplug.h>
+#include <linux/sched/task_stack.h>
+#include <linux/init.h>
+#include <linux/export.h>
+#include <linux/kexec.h>
+
+#include <asm/mmu_context.h>
+#include <asm/time.h>
+#include <asm/setup.h>
+
+#include <asm/octeon/octeon.h>
+
+#include "octeon_boot.h"
+
+volatile unsigned long octeon_processor_boot = 0xff;
+volatile unsigned long octeon_processor_sp;
+volatile unsigned long octeon_processor_gp;
+#ifdef CONFIG_RELOCATABLE
+volatile unsigned long octeon_processor_relocated_kernel_entry;
+#endif /* CONFIG_RELOCATABLE */
+
+#ifdef CONFIG_HOTPLUG_CPU
+uint64_t octeon_bootloader_entry_addr;
+EXPORT_SYMBOL(octeon_bootloader_entry_addr);
+#endif
+
+extern void kernel_entry(unsigned long arg1, ...);
+
+static void octeon_icache_flush(void)
+{
+	asm volatile ("synci 0($0)\n");
+}
+
+static void (*octeon_message_functions[8])(void) = {
+	scheduler_ipi,
+	generic_smp_call_function_interrupt,
+	octeon_icache_flush,
+};
+
+static irqreturn_t mailbox_interrupt(int irq, void *dev_id)
+{
+	u64 mbox_clrx = CVMX_CIU_MBOX_CLRX(cvmx_get_core_num());
+	u64 action;
+	int i;
+
+	/*
+	 * Make sure the function array initialization remains
+	 * correct.
+	 */
+	BUILD_BUG_ON(SMP_RESCHEDULE_YOURSELF != (1 << 0));
+	BUILD_BUG_ON(SMP_CALL_FUNCTION       != (1 << 1));
+	BUILD_BUG_ON(SMP_ICACHE_FLUSH        != (1 << 2));
+
+	/*
+	 * Load the mailbox register to figure out what we're supposed
+	 * to do.
+	 */
+	action = cvmx_read_csr(mbox_clrx);
+
+	if (OCTEON_IS_MODEL(OCTEON_CN68XX))
+		action &= 0xff;
+	else
+		action &= 0xffff;
+
+	/* Clear the mailbox to clear the interrupt */
+	cvmx_write_csr(mbox_clrx, action);
+
+	for (i = 0; i < ARRAY_SIZE(octeon_message_functions) && action;) {
+		if (action & 1) {
+			void (*fn)(void) = octeon_message_functions[i];
+
+			if (fn)
+				fn();
+		}
+		action >>= 1;
+		i++;
+	}
+	return IRQ_HANDLED;
+}
+
+/*
+ * Cause the function described by call_data to be executed on the passed
+ * cpu.	 When the function has finished, increment the finished field of
+ * call_data.
+ */
+void octeon_send_ipi_single(int cpu, unsigned int action)
+{
+	int coreid = cpu_logical_map(cpu);
+	/*
+	pr_info("SMP: Mailbox send cpu=%d, coreid=%d, action=%u\n", cpu,
+	       coreid, action);
+	*/
+	cvmx_write_csr(CVMX_CIU_MBOX_SETX(coreid), action);
+}
+
+static inline void octeon_send_ipi_mask(const struct cpumask *mask,
+					unsigned int action)
+{
+	unsigned int i;
+
+	for_each_cpu(i, mask)
+		octeon_send_ipi_single(i, action);
+}
+
+/*
+ * Detect available CPUs, populate cpu_possible_mask
+ */
+static void octeon_smp_hotplug_setup(void)
+{
+#ifdef CONFIG_HOTPLUG_CPU
+	struct linux_app_boot_info *labi;
+
+	if (!setup_max_cpus)
+		return;
+
+	labi = (struct linux_app_boot_info *)PHYS_TO_XKSEG_CACHED(LABI_ADDR_IN_BOOTLOADER);
+	if (labi->labi_signature != LABI_SIGNATURE) {
+		pr_info("The bootloader on this board does not support HOTPLUG_CPU.");
+		return;
+	}
+
+	octeon_bootloader_entry_addr = labi->InitTLBStart_addr;
+#endif
+}
+
+static void __init octeon_smp_setup(void)
+{
+	const int coreid = cvmx_get_core_num();
+	int cpus;
+	int id;
+	struct cvmx_sysinfo *sysinfo = cvmx_sysinfo_get();
+
+#ifdef CONFIG_HOTPLUG_CPU
+	int core_mask = octeon_get_boot_coremask();
+	unsigned int num_cores = cvmx_octeon_num_cores();
+#endif
+
+	/* The present CPUs are initially just the boot cpu (CPU 0). */
+	for (id = 0; id < NR_CPUS; id++) {
+		set_cpu_possible(id, id == 0);
+		set_cpu_present(id, id == 0);
+	}
+
+	__cpu_number_map[coreid] = 0;
+	__cpu_logical_map[0] = coreid;
+
+	/* The present CPUs get the lowest CPU numbers. */
+	cpus = 1;
+	for (id = 0; id < NR_CPUS; id++) {
+		if ((id != coreid) && cvmx_coremask_is_core_set(&sysinfo->core_mask, id)) {
+			set_cpu_possible(cpus, true);
+			set_cpu_present(cpus, true);
+			__cpu_number_map[id] = cpus;
+			__cpu_logical_map[cpus] = id;
+			cpus++;
+		}
+	}
+
+#ifdef CONFIG_HOTPLUG_CPU
+	/*
+	 * The possible CPUs are all those present on the chip.	 We
+	 * will assign CPU numbers for possible cores as well.	Cores
+	 * are always consecutively numberd from 0.
+	 */
+	for (id = 0; setup_max_cpus && octeon_bootloader_entry_addr &&
+		     id < num_cores && id < NR_CPUS; id++) {
+		if (!(core_mask & (1 << id))) {
+			set_cpu_possible(cpus, true);
+			__cpu_number_map[id] = cpus;
+			__cpu_logical_map[cpus] = id;
+			cpus++;
+		}
+	}
+#endif
+
+	octeon_smp_hotplug_setup();
+}
+
+
+#ifdef CONFIG_RELOCATABLE
+int plat_post_relocation(long offset)
+{
+	unsigned long entry = (unsigned long)kernel_entry;
+
+	/* Send secondaries into relocated kernel */
+	octeon_processor_relocated_kernel_entry = entry + offset;
+
+	return 0;
+}
+#endif /* CONFIG_RELOCATABLE */
+
+/*
+ * Firmware CPU startup hook
+ */
+static int octeon_boot_secondary(int cpu, struct task_struct *idle)
+{
+	int count;
+
+	pr_info("SMP: Booting CPU%02d (CoreId %2d)...\n", cpu,
+		cpu_logical_map(cpu));
+
+	octeon_processor_sp = __KSTK_TOS(idle);
+	octeon_processor_gp = (unsigned long)(task_thread_info(idle));
+	octeon_processor_boot = cpu_logical_map(cpu);
+	mb();
+
+	count = 10000;
+	while (octeon_processor_sp && count) {
+		/* Waiting for processor to get the SP and GP */
+		udelay(1);
+		count--;
+	}
+	if (count == 0) {
+		pr_err("Secondary boot timeout\n");
+		return -ETIMEDOUT;
+	}
+
+	return 0;
+}
+
+/*
+ * After we've done initial boot, this function is called to allow the
+ * board code to clean up state, if needed
+ */
+static void octeon_init_secondary(void)
+{
+	unsigned int sr;
+
+	sr = set_c0_status(ST0_BEV);
+	write_c0_ebase((u32)ebase);
+	write_c0_status(sr);
+
+	octeon_check_cpu_bist();
+	octeon_init_cvmcount();
+
+	octeon_irq_setup_secondary();
+}
+
+/*
+ * Callout to firmware before smp_init
+ */
+static void __init octeon_prepare_cpus(unsigned int max_cpus)
+{
+	/*
+	 * Only the low order mailbox bits are used for IPIs, leave
+	 * the other bits alone.
+	 */
+	cvmx_write_csr(CVMX_CIU_MBOX_CLRX(cvmx_get_core_num()), 0xffff);
+	if (request_irq(OCTEON_IRQ_MBOX0, mailbox_interrupt,
+			IRQF_PERCPU | IRQF_NO_THREAD, "SMP-IPI",
+			mailbox_interrupt)) {
+		panic("Cannot request_irq(OCTEON_IRQ_MBOX0)");
+	}
+}
+
+/*
+ * Last chance for the board code to finish SMP initialization before
+ * the CPU is "online".
+ */
+static void octeon_smp_finish(void)
+{
+	octeon_user_io_init();
+
+	/* to generate the first CPU timer interrupt */
+	write_c0_compare(read_c0_count() + mips_hpt_frequency / HZ);
+	local_irq_enable();
+}
+
+#ifdef CONFIG_HOTPLUG_CPU
+
+/* State of each CPU. */
+static DEFINE_PER_CPU(int, cpu_state);
+
+static int octeon_cpu_disable(void)
+{
+	unsigned int cpu = smp_processor_id();
+
+	if (!octeon_bootloader_entry_addr)
+		return -ENOTSUPP;
+
+	set_cpu_online(cpu, false);
+	calculate_cpu_foreign_map();
+	octeon_fixup_irqs();
+
+	__flush_cache_all();
+	local_flush_tlb_all();
+
+	return 0;
+}
+
+static void octeon_cpu_die(unsigned int cpu)
+{
+	int coreid = cpu_logical_map(cpu);
+	uint32_t mask, new_mask;
+	const struct cvmx_bootmem_named_block_desc *block_desc;
+
+	while (per_cpu(cpu_state, cpu) != CPU_DEAD)
+		cpu_relax();
+
+	/*
+	 * This is a bit complicated strategics of getting/settig available
+	 * cores mask, copied from bootloader
+	 */
+
+	mask = 1 << coreid;
+	/* LINUX_APP_BOOT_BLOCK is initialized in bootoct binary */
+	block_desc = cvmx_bootmem_find_named_block(LINUX_APP_BOOT_BLOCK_NAME);
+
+	if (!block_desc) {
+		struct linux_app_boot_info *labi;
+
+		labi = (struct linux_app_boot_info *)PHYS_TO_XKSEG_CACHED(LABI_ADDR_IN_BOOTLOADER);
+
+		labi->avail_coremask |= mask;
+		new_mask = labi->avail_coremask;
+	} else {		       /* alternative, already initialized */
+		uint32_t *p = (uint32_t *)PHYS_TO_XKSEG_CACHED(block_desc->base_addr +
+							       AVAIL_COREMASK_OFFSET_IN_LINUX_APP_BOOT_BLOCK);
+		*p |= mask;
+		new_mask = *p;
+	}
+
+	pr_info("Reset core %d. Available Coremask = 0x%x \n", coreid, new_mask);
+	mb();
+	cvmx_write_csr(CVMX_CIU_PP_RST, 1 << coreid);
+	cvmx_write_csr(CVMX_CIU_PP_RST, 0);
+}
+
+void play_dead(void)
+{
+	int cpu = cpu_number_map(cvmx_get_core_num());
+
+	idle_task_exit();
+	octeon_processor_boot = 0xff;
+	per_cpu(cpu_state, cpu) = CPU_DEAD;
+
+	mb();
+
+	while (1)	/* core will be reset here */
+		;
+}
+
+static void start_after_reset(void)
+{
+	kernel_entry(0, 0, 0);	/* set a2 = 0 for secondary core */
+}
+
+static int octeon_update_boot_vector(unsigned int cpu)
+{
+
+	int coreid = cpu_logical_map(cpu);
+	uint32_t avail_coremask;
+	const struct cvmx_bootmem_named_block_desc *block_desc;
+	struct boot_init_vector *boot_vect =
+		(struct boot_init_vector *)PHYS_TO_XKSEG_CACHED(BOOTLOADER_BOOT_VECTOR);
+
+	block_desc = cvmx_bootmem_find_named_block(LINUX_APP_BOOT_BLOCK_NAME);
+
+	if (!block_desc) {
+		struct linux_app_boot_info *labi;
+
+		labi = (struct linux_app_boot_info *)PHYS_TO_XKSEG_CACHED(LABI_ADDR_IN_BOOTLOADER);
+
+		avail_coremask = labi->avail_coremask;
+		labi->avail_coremask &= ~(1 << coreid);
+	} else {		       /* alternative, already initialized */
+		avail_coremask = *(uint32_t *)PHYS_TO_XKSEG_CACHED(
+			block_desc->base_addr + AVAIL_COREMASK_OFFSET_IN_LINUX_APP_BOOT_BLOCK);
+	}
+
+	if (!(avail_coremask & (1 << coreid))) {
+		/* core not available, assume, that caught by simple-executive */
+		cvmx_write_csr(CVMX_CIU_PP_RST, 1 << coreid);
+		cvmx_write_csr(CVMX_CIU_PP_RST, 0);
+	}
+
+	boot_vect[coreid].app_start_func_addr =
+		(uint32_t) (unsigned long) start_after_reset;
+	boot_vect[coreid].code_addr = octeon_bootloader_entry_addr;
+
+	mb();
+
+	cvmx_write_csr(CVMX_CIU_NMI, (1 << coreid) & avail_coremask);
+
+	return 0;
+}
+
+static int register_cavium_notifier(void)
+{
+	return cpuhp_setup_state_nocalls(CPUHP_MIPS_SOC_PREPARE,
+					 "mips/cavium:prepare",
+					 octeon_update_boot_vector, NULL);
+}
+late_initcall(register_cavium_notifier);
+
+#endif	/* CONFIG_HOTPLUG_CPU */
+
+static const struct plat_smp_ops octeon_smp_ops = {
+	.send_ipi_single	= octeon_send_ipi_single,
+	.send_ipi_mask		= octeon_send_ipi_mask,
+	.init_secondary		= octeon_init_secondary,
+	.smp_finish		= octeon_smp_finish,
+	.boot_secondary		= octeon_boot_secondary,
+	.smp_setup		= octeon_smp_setup,
+	.prepare_cpus		= octeon_prepare_cpus,
+#ifdef CONFIG_HOTPLUG_CPU
+	.cpu_disable		= octeon_cpu_disable,
+	.cpu_die		= octeon_cpu_die,
+#endif
+#ifdef CONFIG_KEXEC
+	.kexec_nonboot_cpu	= kexec_nonboot_cpu_jump,
+#endif
+};
+
+static irqreturn_t octeon_78xx_reched_interrupt(int irq, void *dev_id)
+{
+	scheduler_ipi();
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t octeon_78xx_call_function_interrupt(int irq, void *dev_id)
+{
+	generic_smp_call_function_interrupt();
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t octeon_78xx_icache_flush_interrupt(int irq, void *dev_id)
+{
+	octeon_icache_flush();
+	return IRQ_HANDLED;
+}
+
+/*
+ * Callout to firmware before smp_init
+ */
+static void octeon_78xx_prepare_cpus(unsigned int max_cpus)
+{
+	if (request_irq(OCTEON_IRQ_MBOX0 + 0,
+			octeon_78xx_reched_interrupt,
+			IRQF_PERCPU | IRQF_NO_THREAD, "Scheduler",
+			octeon_78xx_reched_interrupt)) {
+		panic("Cannot request_irq for SchedulerIPI");
+	}
+	if (request_irq(OCTEON_IRQ_MBOX0 + 1,
+			octeon_78xx_call_function_interrupt,
+			IRQF_PERCPU | IRQF_NO_THREAD, "SMP-Call",
+			octeon_78xx_call_function_interrupt)) {
+		panic("Cannot request_irq for SMP-Call");
+	}
+	if (request_irq(OCTEON_IRQ_MBOX0 + 2,
+			octeon_78xx_icache_flush_interrupt,
+			IRQF_PERCPU | IRQF_NO_THREAD, "ICache-Flush",
+			octeon_78xx_icache_flush_interrupt)) {
+		panic("Cannot request_irq for ICache-Flush");
+	}
+}
+
+static void octeon_78xx_send_ipi_single(int cpu, unsigned int action)
+{
+	int i;
+
+	for (i = 0; i < 8; i++) {
+		if (action & 1)
+			octeon_ciu3_mbox_send(cpu, i);
+		action >>= 1;
+	}
+}
+
+static void octeon_78xx_send_ipi_mask(const struct cpumask *mask,
+				      unsigned int action)
+{
+	unsigned int cpu;
+
+	for_each_cpu(cpu, mask)
+		octeon_78xx_send_ipi_single(cpu, action);
+}
+
+static const struct plat_smp_ops octeon_78xx_smp_ops = {
+	.send_ipi_single	= octeon_78xx_send_ipi_single,
+	.send_ipi_mask		= octeon_78xx_send_ipi_mask,
+	.init_secondary		= octeon_init_secondary,
+	.smp_finish		= octeon_smp_finish,
+	.boot_secondary		= octeon_boot_secondary,
+	.smp_setup		= octeon_smp_setup,
+	.prepare_cpus		= octeon_78xx_prepare_cpus,
+#ifdef CONFIG_HOTPLUG_CPU
+	.cpu_disable		= octeon_cpu_disable,
+	.cpu_die		= octeon_cpu_die,
+#endif
+#ifdef CONFIG_KEXEC
+	.kexec_nonboot_cpu	= kexec_nonboot_cpu_jump,
+#endif
+};
+
+void __init octeon_setup_smp(void)
+{
+	const struct plat_smp_ops *ops;
+
+	if (octeon_has_feature(OCTEON_FEATURE_CIU3))
+		ops = &octeon_78xx_smp_ops;
+	else
+		ops = &octeon_smp_ops;
+
+	register_smp_ops(ops);
+}
diff --git a/arch/mips/cobalt/Makefile b/arch/mips/cobalt/Makefile
new file mode 100644
index 000000000..f0e2c26c8
--- /dev/null
+++ b/arch/mips/cobalt/Makefile
@@ -0,0 +1,8 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Makefile for the Cobalt micro systems family specific parts of the kernel
+#
+
+obj-y := buttons.o irq.o lcd.o led.o mtd.o reset.o rtc.o serial.o setup.o time.o
+
+obj-$(CONFIG_PCI)		+= pci.o
diff --git a/arch/mips/cobalt/Platform b/arch/mips/cobalt/Platform
new file mode 100644
index 000000000..4254895ad
--- /dev/null
+++ b/arch/mips/cobalt/Platform
@@ -0,0 +1,5 @@
+#
+# Cobalt Server
+#
+cflags-$(CONFIG_MIPS_COBALT)	+= -I$(srctree)/arch/mips/include/asm/mach-cobalt
+load-$(CONFIG_MIPS_COBALT)	+= 0xffffffff80080000
diff --git a/arch/mips/cobalt/buttons.c b/arch/mips/cobalt/buttons.c
new file mode 100644
index 000000000..0f9299fe5
--- /dev/null
+++ b/arch/mips/cobalt/buttons.c
@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *  Cobalt buttons platform device.
+ *
+ *  Copyright (C) 2007  Yoichi Yuasa <yuasa@linux-mips.org>
+ */
+
+#include <linux/platform_device.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+
+static struct resource cobalt_buttons_resource __initdata = {
+	.start	= 0x1d000000,
+	.end	= 0x1d000003,
+	.flags	= IORESOURCE_MEM,
+};
+
+static __init int cobalt_add_buttons(void)
+{
+	struct platform_device *pd;
+	int error;
+
+	pd = platform_device_alloc("Cobalt buttons", -1);
+	if (!pd)
+		return -ENOMEM;
+
+	error = platform_device_add_resources(pd, &cobalt_buttons_resource, 1);
+	if (error)
+		goto err_free_device;
+
+	error = platform_device_add(pd);
+	if (error)
+		goto err_free_device;
+
+	return 0;
+
+ err_free_device:
+	platform_device_put(pd);
+	return error;
+}
+device_initcall(cobalt_add_buttons);
diff --git a/arch/mips/cobalt/irq.c b/arch/mips/cobalt/irq.c
new file mode 100644
index 000000000..ead5ae413
--- /dev/null
+++ b/arch/mips/cobalt/irq.c
@@ -0,0 +1,64 @@
+/*
+ * IRQ vector handles
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995, 1996, 1997, 2003 by Ralf Baechle
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/pci.h>
+
+#include <asm/i8259.h>
+#include <asm/irq_cpu.h>
+#include <asm/irq_gt641xx.h>
+#include <asm/gt64120.h>
+
+#include <irq.h>
+
+asmlinkage void plat_irq_dispatch(void)
+{
+	unsigned pending = read_c0_status() & read_c0_cause() & ST0_IM;
+	int irq;
+
+	if (pending & CAUSEF_IP2)
+		gt641xx_irq_dispatch();
+	else if (pending & CAUSEF_IP6) {
+		irq = i8259_irq();
+		if (irq < 0)
+			spurious_interrupt();
+		else
+			do_IRQ(irq);
+	} else if (pending & CAUSEF_IP3)
+		do_IRQ(MIPS_CPU_IRQ_BASE + 3);
+	else if (pending & CAUSEF_IP4)
+		do_IRQ(MIPS_CPU_IRQ_BASE + 4);
+	else if (pending & CAUSEF_IP5)
+		do_IRQ(MIPS_CPU_IRQ_BASE + 5);
+	else if (pending & CAUSEF_IP7)
+		do_IRQ(MIPS_CPU_IRQ_BASE + 7);
+	else
+		spurious_interrupt();
+}
+
+void __init arch_init_irq(void)
+{
+	mips_cpu_irq_init();
+	gt641xx_irq_init();
+	init_i8259_irqs();
+
+	if (request_irq(GT641XX_CASCADE_IRQ, no_action, IRQF_NO_THREAD,
+			"cascade", NULL)) {
+		pr_err("Failed to request irq %d (cascade)\n",
+		       GT641XX_CASCADE_IRQ);
+	}
+	if (request_irq(I8259_CASCADE_IRQ, no_action, IRQF_NO_THREAD,
+			"cascade", NULL)) {
+		pr_err("Failed to request irq %d (cascade)\n",
+		       I8259_CASCADE_IRQ);
+	}
+}
diff --git a/arch/mips/cobalt/lcd.c b/arch/mips/cobalt/lcd.c
new file mode 100644
index 000000000..7d43b5ec3
--- /dev/null
+++ b/arch/mips/cobalt/lcd.c
@@ -0,0 +1,42 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *  Registration of Cobalt LCD platform device.
+ *
+ *  Copyright (C) 2008  Yoichi Yuasa <yuasa@linux-mips.org>
+ */
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/ioport.h>
+#include <linux/platform_device.h>
+
+static struct resource cobalt_lcd_resource __initdata = {
+	.start	= 0x1f000000,
+	.end	= 0x1f00001f,
+	.flags	= IORESOURCE_MEM,
+};
+
+static __init int cobalt_lcd_add(void)
+{
+	struct platform_device *pdev;
+	int retval;
+
+	pdev = platform_device_alloc("cobalt-lcd", -1);
+	if (!pdev)
+		return -ENOMEM;
+
+	retval = platform_device_add_resources(pdev, &cobalt_lcd_resource, 1);
+	if (retval)
+		goto err_free_device;
+
+	retval = platform_device_add(pdev);
+	if (retval)
+		goto err_free_device;
+
+	return 0;
+
+err_free_device:
+	platform_device_put(pdev);
+
+	return retval;
+}
+device_initcall(cobalt_lcd_add);
diff --git a/arch/mips/cobalt/led.c b/arch/mips/cobalt/led.c
new file mode 100644
index 000000000..196660cac
--- /dev/null
+++ b/arch/mips/cobalt/led.c
@@ -0,0 +1,49 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *  Registration of Cobalt LED platform device.
+ *
+ *  Copyright (C) 2007	Yoichi Yuasa <yuasa@linux-mips.org>
+ */
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/ioport.h>
+#include <linux/platform_device.h>
+
+#include <cobalt.h>
+
+static struct resource cobalt_led_resource __initdata = {
+	.start	= 0x1c000000,
+	.end	= 0x1c000000,
+	.flags	= IORESOURCE_MEM,
+};
+
+static __init int cobalt_led_add(void)
+{
+	struct platform_device *pdev;
+	int retval;
+
+	if (cobalt_board_id == COBALT_BRD_ID_QUBE1 ||
+	    cobalt_board_id == COBALT_BRD_ID_QUBE2)
+		pdev = platform_device_alloc("cobalt-qube-leds", -1);
+	else
+		pdev = platform_device_alloc("cobalt-raq-leds", -1);
+
+	if (!pdev)
+		return -ENOMEM;
+
+	retval = platform_device_add_resources(pdev, &cobalt_led_resource, 1);
+	if (retval)
+		goto err_free_device;
+
+	retval = platform_device_add(pdev);
+	if (retval)
+		goto err_free_device;
+
+	return 0;
+
+err_free_device:
+	platform_device_put(pdev);
+
+	return retval;
+}
+device_initcall(cobalt_led_add);
diff --git a/arch/mips/cobalt/mtd.c b/arch/mips/cobalt/mtd.c
new file mode 100644
index 000000000..95f579d8c
--- /dev/null
+++ b/arch/mips/cobalt/mtd.c
@@ -0,0 +1,47 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *  Registration of Cobalt MTD device.
+ *
+ *  Copyright (C) 2006  Yoichi Yuasa <yuasa@linux-mips.org>
+ */
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+
+static struct mtd_partition cobalt_mtd_partitions[] = {
+	{
+		.name	= "firmware",
+		.offset = 0x0,
+		.size	= 0x80000,
+	},
+};
+
+static struct physmap_flash_data cobalt_flash_data = {
+	.width		= 1,
+	.nr_parts	= 1,
+	.parts		= cobalt_mtd_partitions,
+};
+
+static struct resource cobalt_mtd_resource = {
+	.start	= 0x1fc00000,
+	.end	= 0x1fc7ffff,
+	.flags	= IORESOURCE_MEM,
+};
+
+static struct platform_device cobalt_mtd = {
+	.name		= "physmap-flash",
+	.dev		= {
+		.platform_data	= &cobalt_flash_data,
+	},
+	.num_resources	= 1,
+	.resource	= &cobalt_mtd_resource,
+};
+
+static int __init cobalt_mtd_init(void)
+{
+	platform_device_register(&cobalt_mtd);
+
+	return 0;
+}
+device_initcall(cobalt_mtd_init);
diff --git a/arch/mips/cobalt/pci.c b/arch/mips/cobalt/pci.c
new file mode 100644
index 000000000..85ec9cc31
--- /dev/null
+++ b/arch/mips/cobalt/pci.c
@@ -0,0 +1,48 @@
+/*
+ * Register PCI controller.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1996, 1997, 2004, 05 by Ralf Baechle (ralf@linux-mips.org)
+ * Copyright (C) 2001, 2002, 2003 by Liam Davies (ldavies@agile.tv)
+ *
+ */
+#include <linux/init.h>
+#include <linux/pci.h>
+
+#include <asm/gt64120.h>
+
+extern struct pci_ops gt64xxx_pci0_ops;
+
+static struct resource cobalt_mem_resource = {
+	.start	= GT_DEF_PCI0_MEM0_BASE,
+	.end	= GT_DEF_PCI0_MEM0_BASE + GT_DEF_PCI0_MEM0_SIZE - 1,
+	.name	= "PCI memory",
+	.flags	= IORESOURCE_MEM,
+};
+
+static struct resource cobalt_io_resource = {
+	.start	= 0x1000,
+	.end	= 0xffffffUL,
+	.name	= "PCI I/O",
+	.flags	= IORESOURCE_IO,
+};
+
+static struct pci_controller cobalt_pci_controller = {
+	.pci_ops	= &gt64xxx_pci0_ops,
+	.mem_resource	= &cobalt_mem_resource,
+	.io_resource	= &cobalt_io_resource,
+	.io_offset	= 0 - GT_DEF_PCI0_IO_BASE,
+	.io_map_base	= CKSEG1ADDR(GT_DEF_PCI0_IO_BASE),
+};
+
+static int __init cobalt_pci_init(void)
+{
+	register_pci_controller(&cobalt_pci_controller);
+
+	return 0;
+}
+
+arch_initcall(cobalt_pci_init);
diff --git a/arch/mips/cobalt/reset.c b/arch/mips/cobalt/reset.c
new file mode 100644
index 000000000..4eedd481d
--- /dev/null
+++ b/arch/mips/cobalt/reset.c
@@ -0,0 +1,52 @@
+/*
+ * Cobalt Reset operations
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995, 1996, 1997 by Ralf Baechle
+ * Copyright (C) 2001 by Liam Davies (ldavies@agile.tv)
+ */
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/leds.h>
+
+#include <asm/idle.h>
+#include <asm/processor.h>
+
+#include <cobalt.h>
+
+#define RESET_PORT	((void __iomem *)CKSEG1ADDR(0x1c000000))
+#define RESET		0x0f
+
+DEFINE_LED_TRIGGER(power_off_led_trigger);
+
+static int __init ledtrig_power_off_init(void)
+{
+	led_trigger_register_simple("power-off", &power_off_led_trigger);
+	return 0;
+}
+device_initcall(ledtrig_power_off_init);
+
+void cobalt_machine_halt(void)
+{
+	/*
+	 * turn on power off LED on RaQ
+	 */
+	led_trigger_event(power_off_led_trigger, LED_FULL);
+
+	local_irq_disable();
+	while (1) {
+		if (cpu_wait)
+			cpu_wait();
+	}
+}
+
+void cobalt_machine_restart(char *command)
+{
+	writeb(RESET, RESET_PORT);
+
+	/* we should never get here */
+	cobalt_machine_halt();
+}
diff --git a/arch/mips/cobalt/rtc.c b/arch/mips/cobalt/rtc.c
new file mode 100644
index 000000000..0f9ca45da
--- /dev/null
+++ b/arch/mips/cobalt/rtc.c
@@ -0,0 +1,51 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *  Registration of Cobalt RTC platform device.
+ *
+ *  Copyright (C) 2007  Yoichi Yuasa <yuasa@linux-mips.org>
+ */
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/ioport.h>
+#include <linux/mc146818rtc.h>
+#include <linux/platform_device.h>
+
+static struct resource cobalt_rtc_resource[] __initdata = {
+	{
+		.start	= 0x70,
+		.end	= 0x77,
+		.flags	= IORESOURCE_IO,
+	},
+	{
+		.start	= RTC_IRQ,
+		.end	= RTC_IRQ,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static __init int cobalt_rtc_add(void)
+{
+	struct platform_device *pdev;
+	int retval;
+
+	pdev = platform_device_alloc("rtc_cmos", -1);
+	if (!pdev)
+		return -ENOMEM;
+
+	retval = platform_device_add_resources(pdev, cobalt_rtc_resource,
+					       ARRAY_SIZE(cobalt_rtc_resource));
+	if (retval)
+		goto err_free_device;
+
+	retval = platform_device_add(pdev);
+	if (retval)
+		goto err_free_device;
+
+	return 0;
+
+err_free_device:
+	platform_device_put(pdev);
+
+	return retval;
+}
+device_initcall(cobalt_rtc_add);
diff --git a/arch/mips/cobalt/serial.c b/arch/mips/cobalt/serial.c
new file mode 100644
index 000000000..5fb676719
--- /dev/null
+++ b/arch/mips/cobalt/serial.c
@@ -0,0 +1,73 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *  Registration of Cobalt UART platform device.
+ *
+ *  Copyright (C) 2007  Yoichi Yuasa <yuasa@linux-mips.org>
+ */
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/ioport.h>
+#include <linux/platform_device.h>
+#include <linux/serial_8250.h>
+
+#include <cobalt.h>
+#include <irq.h>
+
+static struct resource cobalt_uart_resource[] __initdata = {
+	{
+		.start	= 0x1c800000,
+		.end	= 0x1c800007,
+		.flags	= IORESOURCE_MEM,
+	},
+	{
+		.start	= SERIAL_IRQ,
+		.end	= SERIAL_IRQ,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct plat_serial8250_port cobalt_serial8250_port[] = {
+	{
+		.irq		= SERIAL_IRQ,
+		.uartclk	= 18432000,
+		.iotype		= UPIO_MEM,
+		.flags		= UPF_IOREMAP | UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.mapbase	= 0x1c800000,
+	},
+	{},
+};
+
+static __init int cobalt_uart_add(void)
+{
+	struct platform_device *pdev;
+	int retval;
+
+	/*
+	 * Cobalt Qube1 has no UART.
+	 */
+	if (cobalt_board_id == COBALT_BRD_ID_QUBE1)
+		return 0;
+
+	pdev = platform_device_alloc("serial8250", -1);
+	if (!pdev)
+		return -ENOMEM;
+
+	pdev->id = PLAT8250_DEV_PLATFORM;
+	pdev->dev.platform_data = cobalt_serial8250_port;
+
+	retval = platform_device_add_resources(pdev, cobalt_uart_resource, ARRAY_SIZE(cobalt_uart_resource));
+	if (retval)
+		goto err_free_device;
+
+	retval = platform_device_add(pdev);
+	if (retval)
+		goto err_free_device;
+
+	return 0;
+
+err_free_device:
+	platform_device_put(pdev);
+
+	return retval;
+}
+device_initcall(cobalt_uart_add);
diff --git a/arch/mips/cobalt/setup.c b/arch/mips/cobalt/setup.c
new file mode 100644
index 000000000..2e099d55a
--- /dev/null
+++ b/arch/mips/cobalt/setup.c
@@ -0,0 +1,119 @@
+/*
+ * Setup pointers to hardware dependent routines.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1996, 1997, 2004, 05 by Ralf Baechle (ralf@linux-mips.org)
+ * Copyright (C) 2001, 2002, 2003 by Liam Davies (ldavies@agile.tv)
+ *
+ */
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/ioport.h>
+#include <linux/memblock.h>
+#include <linux/pm.h>
+
+#include <asm/bootinfo.h>
+#include <asm/reboot.h>
+#include <asm/setup.h>
+#include <asm/gt64120.h>
+
+#include <cobalt.h>
+
+extern void cobalt_machine_restart(char *command);
+extern void cobalt_machine_halt(void);
+
+const char *get_system_type(void)
+{
+	switch (cobalt_board_id) {
+		case COBALT_BRD_ID_QUBE1:
+			return "Cobalt Qube";
+		case COBALT_BRD_ID_RAQ1:
+			return "Cobalt RaQ";
+		case COBALT_BRD_ID_QUBE2:
+			return "Cobalt Qube2";
+		case COBALT_BRD_ID_RAQ2:
+			return "Cobalt RaQ2";
+	}
+	return "MIPS Cobalt";
+}
+
+/*
+ * Cobalt doesn't have PS/2 keyboard/mouse interfaces,
+ * keyboard controller is never used.
+ * Also PCI-ISA bridge DMA controller is never used.
+ */
+static struct resource cobalt_reserved_resources[] = {
+	{	/* dma1 */
+		.start	= 0x00,
+		.end	= 0x1f,
+		.name	= "reserved",
+		.flags	= IORESOURCE_BUSY | IORESOURCE_IO,
+	},
+	{	/* keyboard */
+		.start	= 0x60,
+		.end	= 0x6f,
+		.name	= "reserved",
+		.flags	= IORESOURCE_BUSY | IORESOURCE_IO,
+	},
+	{	/* dma page reg */
+		.start	= 0x80,
+		.end	= 0x8f,
+		.name	= "reserved",
+		.flags	= IORESOURCE_BUSY | IORESOURCE_IO,
+	},
+	{	/* dma2 */
+		.start	= 0xc0,
+		.end	= 0xdf,
+		.name	= "reserved",
+		.flags	= IORESOURCE_BUSY | IORESOURCE_IO,
+	},
+};
+
+void __init plat_mem_setup(void)
+{
+	int i;
+
+	_machine_restart = cobalt_machine_restart;
+	_machine_halt = cobalt_machine_halt;
+	pm_power_off = cobalt_machine_halt;
+
+	set_io_port_base(CKSEG1ADDR(GT_DEF_PCI0_IO_BASE));
+
+	/* I/O port resource */
+	ioport_resource.end = 0x01ffffff;
+
+	/* These resources have been reserved by VIA SuperI/O chip. */
+	for (i = 0; i < ARRAY_SIZE(cobalt_reserved_resources); i++)
+		request_resource(&ioport_resource, cobalt_reserved_resources + i);
+}
+
+/*
+ * Prom init. We read our one and only communication with the firmware.
+ * Grab the amount of installed memory.
+ * Better boot loaders (CoLo) pass a command line too :-)
+ */
+
+void __init prom_init(void)
+{
+	unsigned long memsz;
+	int argc, i;
+	char **argv;
+
+	memsz = fw_arg0 & 0x7fff0000;
+	argc = fw_arg0 & 0x0000ffff;
+	argv = (char **)fw_arg1;
+
+	for (i = 1; i < argc; i++) {
+		strlcat(arcs_cmdline, argv[i], COMMAND_LINE_SIZE);
+		if (i < (argc - 1))
+			strlcat(arcs_cmdline, " ", COMMAND_LINE_SIZE);
+	}
+
+	memblock_add(0, memsz);
+
+	setup_8250_early_printk_port(CKSEG1ADDR(0x1c800000), 0, 0);
+}
diff --git a/arch/mips/cobalt/time.c b/arch/mips/cobalt/time.c
new file mode 100644
index 000000000..1b6fa6649
--- /dev/null
+++ b/arch/mips/cobalt/time.c
@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *  Cobalt time initialization.
+ *
+ *  Copyright (C) 2007  Yoichi Yuasa <yuasa@linux-mips.org>
+ */
+#include <linux/i8253.h>
+#include <linux/init.h>
+
+#include <asm/gt64120.h>
+#include <asm/time.h>
+
+#define GT641XX_BASE_CLOCK	50000000	/* 50MHz */
+
+void __init plat_time_init(void)
+{
+	u32 start, end;
+	int i = HZ / 10;
+
+	setup_pit_timer();
+
+	gt641xx_set_base_clock(GT641XX_BASE_CLOCK);
+
+	/*
+	 * MIPS counter frequency is measured during a 100msec interval
+	 * using GT64111 timer0.
+	 */
+	while (!gt641xx_timer0_state())
+		;
+
+	start = read_c0_count();
+
+	while (i--)
+		while (!gt641xx_timer0_state())
+			;
+
+	end = read_c0_count();
+
+	mips_hpt_frequency = (end - start) * 10;
+	printk(KERN_INFO "MIPS counter frequency %dHz\n", mips_hpt_frequency);
+}
diff --git a/arch/mips/configs/ar7_defconfig b/arch/mips/configs/ar7_defconfig
new file mode 100644
index 000000000..ed4a63887
--- /dev/null
+++ b/arch/mips/configs/ar7_defconfig
@@ -0,0 +1,120 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_KERNEL_LZMA=y
+CONFIG_SYSVIPC=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_RELAY=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_EXPERT=y
+# CONFIG_ELF_CORE is not set
+# CONFIG_KALLSYMS is not set
+# CONFIG_VM_EVENT_COUNTERS is not set
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_AR7=y
+CONFIG_HZ_100=y
+CONFIG_KEXEC=y
+# CONFIG_SECCOMP is not set
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_BSD_DISKLABEL=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_MULTIPLE_TABLES=y
+CONFIG_IP_ROUTE_MULTIPATH=y
+CONFIG_IP_ROUTE_VERBOSE=y
+CONFIG_IP_MROUTE=y
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_DIAG is not set
+CONFIG_TCP_CONG_ADVANCED=y
+# CONFIG_TCP_CONG_BIC is not set
+# CONFIG_TCP_CONG_CUBIC is not set
+CONFIG_TCP_CONG_WESTWOOD=y
+# CONFIG_TCP_CONG_HTCP is not set
+# CONFIG_IPV6 is not set
+CONFIG_NETFILTER=y
+# CONFIG_BRIDGE_NETFILTER is not set
+CONFIG_NF_CONNTRACK=m
+CONFIG_NF_CONNTRACK_MARK=y
+CONFIG_NF_CONNTRACK_FTP=m
+CONFIG_NF_CONNTRACK_IRC=m
+CONFIG_NF_CONNTRACK_TFTP=m
+CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
+CONFIG_NETFILTER_XT_MATCH_LIMIT=m
+CONFIG_NETFILTER_XT_MATCH_MAC=m
+CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_STATE=m
+CONFIG_IP_NF_IPTABLES=m
+CONFIG_IP_NF_FILTER=m
+CONFIG_IP_NF_TARGET_REJECT=m
+CONFIG_IP_NF_MANGLE=m
+CONFIG_IP_NF_RAW=m
+CONFIG_ATM=m
+CONFIG_ATM_BR2684=m
+CONFIG_ATM_BR2684_IPFILTER=y
+CONFIG_BRIDGE=y
+CONFIG_VLAN_8021Q=y
+CONFIG_NET_SCHED=y
+CONFIG_NET_CLS_ACT=y
+CONFIG_NET_ACT_POLICE=y
+CONFIG_HAMRADIO=y
+CONFIG_CFG80211=m
+CONFIG_MAC80211=m
+CONFIG_MTD=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_CFI_STAA=y
+CONFIG_MTD_COMPLEX_MAPPINGS=y
+CONFIG_MTD_PHYSMAP=y
+CONFIG_NETDEVICES=y
+CONFIG_CPMAC=y
+CONFIG_FIXED_PHY=y
+CONFIG_PPP=m
+CONFIG_PPP_FILTER=y
+CONFIG_PPP_MULTILINK=y
+CONFIG_PPPOATM=m
+CONFIG_PPPOE=m
+CONFIG_PPP_ASYNC=m
+# CONFIG_INPUT is not set
+# CONFIG_SERIO is not set
+# CONFIG_VT is not set
+# CONFIG_LEGACY_PTYS is not set
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=2
+CONFIG_SERIAL_8250_RUNTIME_UARTS=2
+CONFIG_HW_RANDOM=y
+CONFIG_GPIO_SYSFS=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_AR7_WDT=y
+# CONFIG_USB_SUPPORT is not set
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+# CONFIG_DNOTIFY is not set
+CONFIG_PROC_KCORE=y
+# CONFIG_PROC_PAGE_MONITOR is not set
+CONFIG_TMPFS=y
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_SUMMARY=y
+CONFIG_JFFS2_COMPRESSION_OPTIONS=y
+CONFIG_SQUASHFS=y
+# CONFIG_CRYPTO_HW is not set
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_DEBUG_FS=y
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE="rootfstype=squashfs,jffs2"
diff --git a/arch/mips/configs/ath25_defconfig b/arch/mips/configs/ath25_defconfig
new file mode 100644
index 000000000..afd1c1624
--- /dev/null
+++ b/arch/mips/configs/ath25_defconfig
@@ -0,0 +1,111 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SYSVIPC=y
+# CONFIG_CROSS_MEMORY_ATTACH is not set
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_BLK_DEV_INITRD=y
+# CONFIG_RD_GZIP is not set
+# CONFIG_RD_BZIP2 is not set
+# CONFIG_RD_XZ is not set
+# CONFIG_RD_LZO is not set
+# CONFIG_RD_LZ4 is not set
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+# CONFIG_FHANDLE is not set
+# CONFIG_AIO is not set
+CONFIG_EMBEDDED=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+# CONFIG_SLUB_DEBUG is not set
+# CONFIG_COMPAT_BRK is not set
+CONFIG_ATH25=y
+CONFIG_HZ_100=y
+# CONFIG_SECCOMP is not set
+# CONFIG_SUSPEND is not set
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_COMPACTION is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+# CONFIG_IPV6 is not set
+CONFIG_CFG80211=m
+CONFIG_MAC80211=m
+CONFIG_MAC80211_DEBUGFS=y
+CONFIG_MTD=y
+CONFIG_MTD_REDBOOT_PARTS=y
+CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-2
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_ADV_OPTIONS=y
+CONFIG_MTD_CFI_GEOMETRY=y
+# CONFIG_MTD_MAP_BANK_WIDTH_1 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_4 is not set
+# CONFIG_MTD_CFI_I2 is not set
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_COMPLEX_MAPPINGS=y
+CONFIG_MTD_PHYSMAP=y
+CONFIG_NETDEVICES=y
+# CONFIG_ETHERNET is not set
+# CONFIG_WLAN_VENDOR_ADMTEK is not set
+CONFIG_ATH5K=m
+# CONFIG_WLAN_VENDOR_ATMEL is not set
+# CONFIG_WLAN_VENDOR_BROADCOM is not set
+# CONFIG_WLAN_VENDOR_CISCO is not set
+# CONFIG_WLAN_VENDOR_INTEL is not set
+# CONFIG_WLAN_VENDOR_INTERSIL is not set
+# CONFIG_WLAN_VENDOR_MARVELL is not set
+# CONFIG_WLAN_VENDOR_MEDIATEK is not set
+# CONFIG_WLAN_VENDOR_RALINK is not set
+# CONFIG_WLAN_VENDOR_REALTEK is not set
+# CONFIG_WLAN_VENDOR_RSI is not set
+# CONFIG_WLAN_VENDOR_ST is not set
+# CONFIG_WLAN_VENDOR_TI is not set
+# CONFIG_WLAN_VENDOR_ZYDAS is not set
+CONFIG_INPUT=m
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+# CONFIG_VT is not set
+# CONFIG_LEGACY_PTYS is not set
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+# CONFIG_SERIAL_8250_PCI is not set
+CONFIG_SERIAL_8250_NR_UARTS=1
+CONFIG_SERIAL_8250_RUNTIME_UARTS=1
+# CONFIG_HW_RANDOM is not set
+# CONFIG_HWMON is not set
+# CONFIG_VGA_ARB is not set
+CONFIG_USB=m
+CONFIG_USB_EHCI_HCD=m
+CONFIG_LEDS_CLASS=y
+# CONFIG_IOMMU_SUPPORT is not set
+# CONFIG_DNOTIFY is not set
+# CONFIG_PROC_PAGE_MONITOR is not set
+CONFIG_TMPFS=y
+CONFIG_TMPFS_XATTR=y
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_SUMMARY=y
+CONFIG_JFFS2_FS_XATTR=y
+# CONFIG_JFFS2_FS_POSIX_ACL is not set
+# CONFIG_JFFS2_FS_SECURITY is not set
+CONFIG_JFFS2_COMPRESSION_OPTIONS=y
+# CONFIG_JFFS2_ZLIB is not set
+CONFIG_SQUASHFS=y
+CONFIG_SQUASHFS_FILE_DIRECT=y
+CONFIG_SQUASHFS_DECOMP_MULTI_PERCPU=y
+# CONFIG_SQUASHFS_ZLIB is not set
+CONFIG_SQUASHFS_XZ=y
+# CONFIG_XZ_DEC_X86 is not set
+# CONFIG_XZ_DEC_POWERPC is not set
+# CONFIG_XZ_DEC_IA64 is not set
+# CONFIG_XZ_DEC_ARM is not set
+# CONFIG_XZ_DEC_ARMTHUMB is not set
+# CONFIG_XZ_DEC_SPARC is not set
+CONFIG_PRINTK_TIME=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_DEBUG_FS=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_FTRACE is not set
diff --git a/arch/mips/configs/ath79_defconfig b/arch/mips/configs/ath79_defconfig
new file mode 100644
index 000000000..0b741716c
--- /dev/null
+++ b/arch/mips/configs/ath79_defconfig
@@ -0,0 +1,89 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SYSVIPC=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_BLK_DEV_INITRD=y
+# CONFIG_RD_GZIP is not set
+# CONFIG_AIO is not set
+# CONFIG_KALLSYMS is not set
+CONFIG_EMBEDDED=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+# CONFIG_SLUB_DEBUG is not set
+# CONFIG_COMPAT_BRK is not set
+CONFIG_ATH79=y
+CONFIG_HZ_100=y
+# CONFIG_SECCOMP is not set
+CONFIG_PCI=y
+# CONFIG_SUSPEND is not set
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+# CONFIG_IPV6 is not set
+CONFIG_CFG80211=m
+CONFIG_MAC80211=m
+CONFIG_MAC80211_DEBUGFS=y
+CONFIG_MTD=y
+CONFIG_MTD_REDBOOT_PARTS=y
+CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-2
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_JEDECPROBE=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_COMPLEX_MAPPINGS=y
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_SPI_NOR=y
+CONFIG_NETDEVICES=y
+CONFIG_ATH9K=m
+CONFIG_ATH9K_AHB=y
+CONFIG_INPUT=m
+# CONFIG_KEYBOARD_ATKBD is not set
+CONFIG_KEYBOARD_GPIO_POLLED=m
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_MISC=y
+# CONFIG_SERIO is not set
+# CONFIG_VT is not set
+# CONFIG_LEGACY_PTYS is not set
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+# CONFIG_SERIAL_8250_PCI is not set
+CONFIG_SERIAL_8250_NR_UARTS=1
+CONFIG_SERIAL_8250_RUNTIME_UARTS=1
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_SERIAL_AR933X=y
+CONFIG_SERIAL_AR933X_CONSOLE=y
+# CONFIG_HW_RANDOM is not set
+CONFIG_I2C=y
+# CONFIG_I2C_COMPAT is not set
+# CONFIG_I2C_HELPER_AUTO is not set
+CONFIG_I2C_GPIO=y
+CONFIG_SPI=y
+CONFIG_SPI_ATH79=y
+CONFIG_SPI_GPIO=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_GPIO_PCF857X=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_ATH79_WDT=y
+# CONFIG_VGA_ARB is not set
+# CONFIG_HID is not set
+# CONFIG_USB_HID is not set
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+CONFIG_USB_OHCI_HCD=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+# CONFIG_IOMMU_SUPPORT is not set
+# CONFIG_DNOTIFY is not set
+# CONFIG_PROC_PAGE_MONITOR is not set
+CONFIG_CRC_ITU_T=m
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_DEBUG_FS=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_FTRACE is not set
diff --git a/arch/mips/configs/bcm47xx_defconfig b/arch/mips/configs/bcm47xx_defconfig
new file mode 100644
index 000000000..22ffde722
--- /dev/null
+++ b/arch/mips/configs/bcm47xx_defconfig
@@ -0,0 +1,81 @@
+CONFIG_SYSVIPC=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_EMBEDDED=y
+CONFIG_SLAB=y
+CONFIG_BCM47XX=y
+CONFIG_PCI=y
+# CONFIG_SUSPEND is not set
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_MULTIPLE_TABLES=y
+CONFIG_IP_ROUTE_MULTIPATH=y
+CONFIG_IP_MROUTE=y
+CONFIG_IP_MROUTE_MULTIPLE_TABLES=y
+CONFIG_SYN_COOKIES=y
+CONFIG_TCP_CONG_ADVANCED=y
+CONFIG_IPV6_MULTIPLE_TABLES=y
+CONFIG_IPV6_SUBTREES=y
+CONFIG_IPV6_MROUTE=y
+CONFIG_NETFILTER=y
+CONFIG_VLAN_8021Q=y
+CONFIG_NET_SCHED=y
+CONFIG_NET_SCH_FQ_CODEL=y
+CONFIG_HAMRADIO=y
+CONFIG_CFG80211=y
+CONFIG_MAC80211=y
+CONFIG_MTD=y
+CONFIG_MTD_BCM47XX_PARTS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_COMPLEX_MAPPINGS=y
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_BCM47XXSFLASH=y
+CONFIG_MTD_RAW_NAND=y
+CONFIG_MTD_NAND_BCM47XXNFLASH=y
+CONFIG_NETDEVICES=y
+CONFIG_B44=y
+CONFIG_TIGON3=y
+CONFIG_ATH5K=y
+CONFIG_B43=y
+CONFIG_B43LEGACY=y
+CONFIG_BRCMSMAC=y
+CONFIG_ISDN=y
+CONFIG_SERIAL_8250=y
+# CONFIG_SERIAL_8250_DEPRECATED_OPTIONS is not set
+CONFIG_SERIAL_8250_CONSOLE=y
+# CONFIG_SERIAL_8250_PCI is not set
+CONFIG_SERIAL_8250_NR_UARTS=2
+CONFIG_SERIAL_8250_RUNTIME_UARTS=2
+CONFIG_SERIAL_8250_EXTENDED=y
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+CONFIG_HW_RANDOM=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_WATCHDOG=y
+CONFIG_BCM47XX_WDT=y
+CONFIG_SSB_DRIVER_GIGE=y
+CONFIG_BCMA_DRIVER_GMAC_CMN=y
+CONFIG_USB=y
+CONFIG_USB_HCD_BCMA=y
+CONFIG_USB_HCD_SSB=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+CONFIG_CRC32_SARWATE=y
+CONFIG_PRINTK_TIME=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
+CONFIG_DEBUG_INFO_REDUCED=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_DEBUG_FS=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE="console=ttyS0,115200"
diff --git a/arch/mips/configs/bcm63xx_defconfig b/arch/mips/configs/bcm63xx_defconfig
new file mode 100644
index 000000000..34d0ca638
--- /dev/null
+++ b/arch/mips/configs/bcm63xx_defconfig
@@ -0,0 +1,66 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+# CONFIG_SWAP is not set
+CONFIG_NO_HZ=y
+CONFIG_EXPERT=y
+# CONFIG_FUTEX is not set
+# CONFIG_EPOLL is not set
+# CONFIG_SIGNALFD is not set
+# CONFIG_TIMERFD is not set
+# CONFIG_EVENTFD is not set
+# CONFIG_SHMEM is not set
+# CONFIG_AIO is not set
+# CONFIG_VM_EVENT_COUNTERS is not set
+# CONFIG_SLUB_DEBUG is not set
+CONFIG_BCM63XX=y
+CONFIG_BCM63XX_CPU_6338=y
+CONFIG_BCM63XX_CPU_6345=y
+CONFIG_BCM63XX_CPU_6348=y
+CONFIG_BCM63XX_CPU_6358=y
+# CONFIG_SECCOMP is not set
+CONFIG_PCI=y
+CONFIG_PCCARD=y
+CONFIG_PCMCIA_BCM63XX=y
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_NET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+# CONFIG_INET_DIAG is not set
+# CONFIG_IPV6 is not set
+CONFIG_CFG80211=y
+CONFIG_NL80211_TESTMODE=y
+CONFIG_MAC80211=y
+# CONFIG_STANDALONE is not set
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+CONFIG_MTD=y
+CONFIG_MTD_BCM63XX_PARTS=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_PHYSMAP=y
+# CONFIG_BLK_DEV is not set
+CONFIG_NETDEVICES=y
+CONFIG_BCM63XX_ENET=y
+CONFIG_BCM63XX_PHY=y
+CONFIG_B43=y
+# CONFIG_B43_PHY_LP is not set
+# CONFIG_INPUT is not set
+# CONFIG_SERIO is not set
+# CONFIG_VT is not set
+# CONFIG_UNIX98_PTYS is not set
+CONFIG_SERIAL_BCM63XX=y
+CONFIG_SERIAL_BCM63XX_CONSOLE=y
+# CONFIG_HW_RANDOM is not set
+# CONFIG_HWMON is not set
+# CONFIG_VGA_ARB is not set
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+CONFIG_USB_OHCI_HCD=y
+# CONFIG_FILE_LOCKING is not set
+# CONFIG_DNOTIFY is not set
+CONFIG_PROC_KCORE=y
+# CONFIG_NETWORK_FILESYSTEMS is not set
+# CONFIG_CRYPTO_HW is not set
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE="console=ttyS0,115200"
diff --git a/arch/mips/configs/bigsur_defconfig b/arch/mips/configs/bigsur_defconfig
new file mode 100644
index 000000000..d15961f00
--- /dev/null
+++ b/arch/mips/configs/bigsur_defconfig
@@ -0,0 +1,248 @@
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_AUDIT=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_TASKSTATS=y
+CONFIG_TASK_DELAY_ACCT=y
+CONFIG_TASK_XACCT=y
+CONFIG_TASK_IO_ACCOUNTING=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=16
+CONFIG_NAMESPACES=y
+CONFIG_USER_NS=y
+CONFIG_RELAY=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_EXPERT=y
+CONFIG_SLAB=y
+CONFIG_SIBYTE_BIGSUR=y
+CONFIG_64BIT=y
+CONFIG_SMP=y
+CONFIG_HZ_1000=y
+CONFIG_PCI=y
+CONFIG_PCI_DEBUG=y
+CONFIG_MIPS32_O32=y
+CONFIG_MIPS32_N32=y
+CONFIG_PM=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_XFRM_USER=m
+CONFIG_NET_KEY=y
+CONFIG_NET_KEY_MIGRATE=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_MROUTE=y
+CONFIG_IP_PIMSM_V1=y
+CONFIG_IP_PIMSM_V2=y
+CONFIG_INET_AH=m
+CONFIG_INET_ESP=m
+CONFIG_INET_IPCOMP=m
+CONFIG_TCP_MD5SIG=y
+CONFIG_IPV6_ROUTER_PREF=y
+CONFIG_IPV6_ROUTE_INFO=y
+CONFIG_IPV6_OPTIMISTIC_DAD=y
+CONFIG_INET6_AH=m
+CONFIG_INET6_ESP=m
+CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_MIP6=m
+CONFIG_IPV6_SIT_6RD=y
+CONFIG_IPV6_TUNNEL=m
+CONFIG_IPV6_MULTIPLE_TABLES=y
+CONFIG_IPV6_SUBTREES=y
+CONFIG_NETLABEL=y
+CONFIG_NETFILTER=y
+# CONFIG_NETFILTER_ADVANCED is not set
+CONFIG_IP_VS=m
+CONFIG_IP_VS_IPV6=y
+CONFIG_IP_VS_PROTO_TCP=y
+CONFIG_IP_VS_PROTO_UDP=y
+CONFIG_IP_VS_PROTO_ESP=y
+CONFIG_IP_VS_PROTO_AH=y
+CONFIG_IP_VS_PROTO_SCTP=y
+CONFIG_IP_VS_RR=m
+CONFIG_IP_VS_WRR=m
+CONFIG_IP_VS_LC=m
+CONFIG_IP_VS_WLC=m
+CONFIG_IP_VS_LBLC=m
+CONFIG_IP_VS_LBLCR=m
+CONFIG_IP_VS_DH=m
+CONFIG_IP_VS_SH=m
+CONFIG_IP_VS_SED=m
+CONFIG_IP_VS_NQ=m
+CONFIG_IP_VS_FTP=m
+CONFIG_IP_DCCP=m
+CONFIG_BRIDGE=m
+CONFIG_VLAN_8021Q=m
+CONFIG_VLAN_8021Q_GVRP=y
+CONFIG_HAMRADIO=y
+CONFIG_AX25=m
+CONFIG_NETROM=m
+CONFIG_ROSE=m
+CONFIG_MKISS=m
+CONFIG_6PACK=m
+CONFIG_BPQETHER=m
+CONFIG_BAYCOM_SER_FDX=m
+CONFIG_BAYCOM_SER_HDX=m
+CONFIG_YAM=m
+CONFIG_FW_LOADER=m
+CONFIG_BLK_DEV_LOOP=m
+CONFIG_BLK_DEV_NBD=m
+CONFIG_EEPROM_LEGACY=y
+CONFIG_EEPROM_MAX6875=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_CHR_DEV_ST=y
+CONFIG_BLK_DEV_SR=y
+CONFIG_CHR_DEV_SG=m
+CONFIG_CHR_DEV_SCH=m
+CONFIG_ATA=y
+CONFIG_SATA_SIL24=y
+CONFIG_PATA_CMD64X=y
+CONFIG_PATA_IT8213=m
+CONFIG_PATA_SIL680=y
+CONFIG_ATA_GENERIC=y
+CONFIG_PATA_LEGACY=y
+CONFIG_NETDEVICES=y
+CONFIG_SB1250_MAC=y
+CONFIG_CHELSIO_T3=m
+CONFIG_NETXEN_NIC=m
+CONFIG_PPP=m
+CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_FILTER=y
+CONFIG_PPP_MPPE=m
+CONFIG_PPP_MULTILINK=y
+CONFIG_PPPOE=m
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
+CONFIG_SLIP=m
+CONFIG_SLIP_COMPRESSED=y
+CONFIG_SLIP_SMART=y
+CONFIG_SLIP_MODE_SLIP6=y
+# CONFIG_INPUT is not set
+CONFIG_SERIO_RAW=m
+# CONFIG_VT is not set
+CONFIG_SERIAL_NONSTANDARD=y
+# CONFIG_HW_RANDOM is not set
+CONFIG_I2C=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_SIBYTE=y
+CONFIG_I2C_DEBUG_CORE=y
+CONFIG_I2C_DEBUG_ALGO=y
+CONFIG_I2C_DEBUG_BUS=y
+# CONFIG_HWMON is not set
+CONFIG_EXT2_FS=m
+CONFIG_EXT2_FS_XATTR=y
+CONFIG_EXT2_FS_POSIX_ACL=y
+CONFIG_EXT2_FS_SECURITY=y
+CONFIG_EXT3_FS=m
+CONFIG_EXT3_FS_POSIX_ACL=y
+CONFIG_EXT3_FS_SECURITY=y
+CONFIG_EXT4_FS=y
+CONFIG_QUOTA=y
+CONFIG_QUOTA_NETLINK_INTERFACE=y
+# CONFIG_PRINT_QUOTA_WARNING is not set
+CONFIG_QFMT_V2=m
+CONFIG_AUTOFS4_FS=m
+CONFIG_FUSE_FS=m
+CONFIG_ISO9660_FS=m
+CONFIG_JOLIET=y
+CONFIG_ZISOFS=y
+CONFIG_UDF_FS=m
+CONFIG_MSDOS_FS=m
+CONFIG_VFAT_FS=m
+CONFIG_NTFS_FS=m
+CONFIG_NTFS_RW=y
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_NFS_FS=y
+CONFIG_ROOT_NFS=y
+CONFIG_NLS_CODEPAGE_437=m
+CONFIG_NLS_CODEPAGE_737=m
+CONFIG_NLS_CODEPAGE_775=m
+CONFIG_NLS_CODEPAGE_850=m
+CONFIG_NLS_CODEPAGE_852=m
+CONFIG_NLS_CODEPAGE_855=m
+CONFIG_NLS_CODEPAGE_857=m
+CONFIG_NLS_CODEPAGE_860=m
+CONFIG_NLS_CODEPAGE_861=m
+CONFIG_NLS_CODEPAGE_862=m
+CONFIG_NLS_CODEPAGE_863=m
+CONFIG_NLS_CODEPAGE_864=m
+CONFIG_NLS_CODEPAGE_865=m
+CONFIG_NLS_CODEPAGE_866=m
+CONFIG_NLS_CODEPAGE_869=m
+CONFIG_NLS_CODEPAGE_936=m
+CONFIG_NLS_CODEPAGE_950=m
+CONFIG_NLS_CODEPAGE_932=m
+CONFIG_NLS_CODEPAGE_949=m
+CONFIG_NLS_CODEPAGE_874=m
+CONFIG_NLS_ISO8859_8=m
+CONFIG_NLS_CODEPAGE_1250=m
+CONFIG_NLS_CODEPAGE_1251=m
+CONFIG_NLS_ASCII=m
+CONFIG_NLS_ISO8859_1=m
+CONFIG_NLS_ISO8859_2=m
+CONFIG_NLS_ISO8859_3=m
+CONFIG_NLS_ISO8859_4=m
+CONFIG_NLS_ISO8859_5=m
+CONFIG_NLS_ISO8859_6=m
+CONFIG_NLS_ISO8859_7=m
+CONFIG_NLS_ISO8859_9=m
+CONFIG_NLS_ISO8859_13=m
+CONFIG_NLS_ISO8859_14=m
+CONFIG_NLS_ISO8859_15=m
+CONFIG_NLS_KOI8_R=m
+CONFIG_NLS_KOI8_U=m
+CONFIG_NLS_UTF8=m
+CONFIG_KEYS=y
+CONFIG_SECURITY=y
+CONFIG_SECURITY_NETWORK=y
+CONFIG_SECURITY_NETWORK_XFRM=y
+CONFIG_SECURITY_SELINUX=y
+CONFIG_SECURITY_SELINUX_BOOTPARAM=y
+CONFIG_SECURITY_SELINUX_DISABLE=y
+CONFIG_DEFAULT_SECURITY_DAC=y
+CONFIG_CRYPTO_NULL=y
+CONFIG_CRYPTO_CCM=m
+CONFIG_CRYPTO_GCM=m
+CONFIG_CRYPTO_CTS=m
+CONFIG_CRYPTO_LRW=m
+CONFIG_CRYPTO_PCBC=m
+CONFIG_CRYPTO_XTS=m
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_XCBC=m
+CONFIG_CRYPTO_VMAC=m
+CONFIG_CRYPTO_MD4=m
+CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_RMD160=m
+CONFIG_CRYPTO_SHA512=m
+CONFIG_CRYPTO_WP512=m
+CONFIG_CRYPTO_ANUBIS=m
+CONFIG_CRYPTO_BLOWFISH=m
+CONFIG_CRYPTO_CAMELLIA=m
+CONFIG_CRYPTO_CAST6=m
+CONFIG_CRYPTO_FCRYPT=m
+CONFIG_CRYPTO_KHAZAD=m
+CONFIG_CRYPTO_SEED=m
+CONFIG_CRYPTO_SERPENT=m
+CONFIG_CRYPTO_TEA=m
+CONFIG_CRYPTO_TWOFISH=m
+CONFIG_CRYPTO_LZO=m
+CONFIG_CRC_T10DIF=m
+CONFIG_CRC7=m
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_MEMORY_INIT=y
+CONFIG_DETECT_HUNG_TASK=y
+CONFIG_DEBUG_LIST=y
diff --git a/arch/mips/configs/bmips_be_defconfig b/arch/mips/configs/bmips_be_defconfig
new file mode 100644
index 000000000..daef132d0
--- /dev/null
+++ b/arch/mips/configs/bmips_be_defconfig
@@ -0,0 +1,76 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+# CONFIG_SWAP is not set
+CONFIG_NO_HZ=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_EXPERT=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+# CONFIG_SLUB_DEBUG is not set
+CONFIG_BMIPS_GENERIC=y
+CONFIG_HIGHMEM=y
+CONFIG_SMP=y
+CONFIG_NR_CPUS=4
+# CONFIG_SECCOMP is not set
+CONFIG_MIPS_O32_FP64_SUPPORT=y
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_PACKET_DIAG=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+# CONFIG_INET_DIAG is not set
+CONFIG_CFG80211=y
+CONFIG_NL80211_TESTMODE=y
+CONFIG_MAC80211=y
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+# CONFIG_STANDALONE is not set
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+CONFIG_MTD=y
+CONFIG_MTD_BCM63XX_PARTS=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_PHYSMAP=y
+# CONFIG_BLK_DEV is not set
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_NETDEVICES=y
+CONFIG_BCMGENET=y
+CONFIG_USB_USBNET=y
+# CONFIG_INPUT is not set
+# CONFIG_SERIO is not set
+# CONFIG_VT is not set
+CONFIG_SERIAL_BCM63XX=y
+CONFIG_SERIAL_BCM63XX_CONSOLE=y
+# CONFIG_HW_RANDOM is not set
+CONFIG_POWER_RESET=y
+CONFIG_POWER_RESET_SYSCON=y
+CONFIG_POWER_SUPPLY=y
+# CONFIG_HWMON is not set
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+CONFIG_USB_EHCI_HCD_PLATFORM=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_HCD_PLATFORM=y
+CONFIG_USB_STORAGE=y
+CONFIG_EXT4_FS=y
+CONFIG_EXT4_FS_POSIX_ACL=y
+CONFIG_EXT4_FS_SECURITY=y
+# CONFIG_DNOTIFY is not set
+CONFIG_FUSE_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_NFS_FS=y
+CONFIG_CIFS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+# CONFIG_CRYPTO_HW is not set
+CONFIG_PRINTK_TIME=y
+CONFIG_DEBUG_FS=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE="earlycon"
diff --git a/arch/mips/configs/bmips_stb_defconfig b/arch/mips/configs/bmips_stb_defconfig
new file mode 100644
index 000000000..cd0dc37c3
--- /dev/null
+++ b/arch/mips/configs/bmips_stb_defconfig
@@ -0,0 +1,210 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+# CONFIG_SWAP is not set
+CONFIG_NO_HZ=y
+CONFIG_HZ=1000
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_EXPERT=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+# CONFIG_SLUB_DEBUG is not set
+CONFIG_BMIPS_GENERIC=y
+CONFIG_CPU_LITTLE_ENDIAN=y
+CONFIG_HIGHMEM=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_SMP=y
+CONFIG_NR_CPUS=4
+# CONFIG_SECCOMP is not set
+CONFIG_MIPS_O32_FP64_SUPPORT=y
+# CONFIG_RD_GZIP is not set
+# CONFIG_RD_BZIP2 is not set
+# CONFIG_RD_LZMA is not set
+CONFIG_RD_XZ=y
+# CONFIG_RD_LZO is not set
+# CONFIG_RD_LZ4 is not set
+CONFIG_PCI=y
+CONFIG_PCI_MSI=y
+CONFIG_PCIEASPM_POWERSAVE=y
+CONFIG_PCIEPORTBUS=y
+CONFIG_PCIE_BRCMSTB=y
+CONFIG_CPU_FREQ=y
+CONFIG_CPU_FREQ_STAT=y
+CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
+CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
+CONFIG_CPU_FREQ_GOV_POWERSAVE=y
+CONFIG_CPU_FREQ_GOV_USERSPACE=y
+CONFIG_CPU_FREQ_GOV_ONDEMAND=y
+CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y
+CONFIG_BMIPS_CPUFREQ=y
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_PACKET_DIAG=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+# CONFIG_INET_DIAG is not set
+CONFIG_CFG80211=y
+CONFIG_NL80211_TESTMODE=y
+CONFIG_WIRELESS=y
+CONFIG_MAC80211=y
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+# CONFIG_STANDALONE is not set
+# CONFIG_PREVENT_FIRMWARE_BUILD is not set
+CONFIG_BRCMSTB_GISB_ARB=y
+CONFIG_MODULES=y
+CONFIG_MODULE_FORCE_LOAD=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+CONFIG_IP_MROUTE=y
+CONFIG_IP_PIMSM_V1=y
+CONFIG_IP_PIMSM_V2=y
+CONFIG_INET_UDP_DIAG=y
+CONFIG_TCP_CONG_ADVANCED=y
+CONFIG_TCP_CONG_BIC=y
+# CONFIG_TCP_CONG_WESTWOOD is not set
+# CONFIG_TCP_CONG_HTCP is not set
+# CONFIG_IPV6 is not set
+CONFIG_IP_NF_IPTABLES=y
+CONFIG_IP_NF_FILTER=y
+CONFIG_NETFILTER=y
+CONFIG_NETFILTER_XTABLES=y
+CONFIG_BRIDGE=y
+CONFIG_BRIDGE_NETFILTER=m
+CONFIG_BRIDGE_NF_EBTABLES=m
+CONFIG_BRIDGE_EBT_BROUTE=m
+CONFIG_NET_DSA=y
+CONFIG_NET_SWITCHDEV=y
+CONFIG_DMA_CMA=y
+CONFIG_CMA_ALIGNMENT=12
+CONFIG_SPI=y
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_JEDECPROBE=y
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_CFI_STAA=y
+CONFIG_MTD_ROM=y
+CONFIG_MTD_ABSENT=y
+CONFIG_MTD_PHYSMAP_OF=y
+CONFIG_MTD_NAND_BRCMNAND=y
+CONFIG_MTD_SPI_NOR=y
+# CONFIG_MTD_SPI_NOR_USE_4K_SECTORS is not set
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_GLUEBI=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_SIZE=8192
+# CONFIG_BLK_DEV is not set
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_CHR_DEV_SG=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_NETDEVICES=y
+CONFIG_VLAN_8021Q=y
+CONFIG_MACVLAN=y
+CONFIG_BCMGENET=y
+CONFIG_USB_USBNET=y
+CONFIG_INPUT_EVDEV=y
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_MISC=y
+CONFIG_INPUT_UINPUT=y
+# CONFIG_SERIO is not set
+CONFIG_VT=y
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_SERIAL_8250=y
+# CONFIG_SERIAL_8250_DEPRECATED_OPTIONS is not set
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_OF_PLATFORM=y
+# CONFIG_HW_RANDOM is not set
+CONFIG_POWER_RESET=y
+CONFIG_POWER_RESET_BRCMSTB=y
+CONFIG_POWER_RESET_SYSCON=y
+CONFIG_POWER_SUPPLY=y
+# CONFIG_HWMON is not set
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+CONFIG_USB_EHCI_HCD_PLATFORM=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_HCD_PLATFORM=y
+CONFIG_USB_STORAGE=y
+CONFIG_SOC_BRCMSTB=y
+CONFIG_MMC=y
+CONFIG_MMC_BLOCK_MINORS=16
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
+CONFIG_EXT4_FS=y
+CONFIG_EXT4_FS_POSIX_ACL=y
+CONFIG_EXT4_FS_SECURITY=y
+# CONFIG_DNOTIFY is not set
+CONFIG_PROC_KCORE=y
+CONFIG_CIFS=y
+CONFIG_JBD2_DEBUG=y
+CONFIG_FUSE_FS=y
+CONFIG_FHANDLE=y
+CONFIG_CGROUPS=y
+CONFIG_CUSE=y
+CONFIG_ISO9660_FS=y
+CONFIG_JOLIET=y
+CONFIG_ZISOFS=y
+CONFIG_UDF_FS=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_TMPFS=y
+CONFIG_JFFS2_FS=y
+CONFIG_UBIFS_FS=y
+CONFIG_SQUASHFS=y
+CONFIG_SQUASHFS_LZO=y
+CONFIG_SQUASHFS_XZ=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_V4=y
+CONFIG_NFS_V4_1=y
+CONFIG_NFS_V4_2=y
+CONFIG_ROOT_NFS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_PRINTK_TIME=y
+CONFIG_DYNAMIC_DEBUG=y
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_DEBUG_INFO_REDUCED is not set
+CONFIG_DEBUG_FS=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_LOCKUP_DETECTOR=y
+CONFIG_DEBUG_USER=y
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE="earlycon"
+# CONFIG_MIPS_CMDLINE_FROM_DTB is not set
+CONFIG_MIPS_CMDLINE_DTB_EXTEND=y
+# CONFIG_MIPS_CMDLINE_FROM_BOOTLOADER is not set
+# CONFIG_CRYPTO_HW is not set
+CONFIG_FW_CFE=y
+CONFIG_ATA=y
+CONFIG_SATA_AHCI_PLATFORM=y
+CONFIG_GENERIC_PHY=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_PHY_BRCM_USB=y
+CONFIG_PHY_BRCM_SATA=y
+CONFIG_PM_DEBUG=y
+CONFIG_SYSVIPC=y
+CONFIG_FUNCTION_GRAPH_TRACER=y
+CONFIG_DYNAMIC_FTRACE=y
+CONFIG_FUNCTION_TRACER=y
+CONFIG_FUNCTION_PROFILER=y
+CONFIG_IRQSOFF_TRACER=y
+CONFIG_SCHED_TRACER=y
+CONFIG_BLK_DEV_IO_TRACE=y
+CONFIG_FTRACE_SYSCALLS=y
+CONFIG_TRACER_SNAPSHOT=y
+CONFIG_TRACER_SNAPSHOT_PER_CPU_SWAP=y
+CONFIG_STACK_TRACER=y
+CONFIG_AHCI_BRCM=y
+CONFIG_MTD_RAW_NAND=y
diff --git a/arch/mips/configs/cavium_octeon_defconfig b/arch/mips/configs/cavium_octeon_defconfig
new file mode 100644
index 000000000..0bc2e3cc5
--- /dev/null
+++ b/arch/mips/configs/cavium_octeon_defconfig
@@ -0,0 +1,167 @@
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_PREEMPT=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_RELAY=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_EXPERT=y
+CONFIG_SLAB=y
+CONFIG_CAVIUM_OCTEON_SOC=y
+CONFIG_CAVIUM_CN63XXP1=y
+CONFIG_CAVIUM_OCTEON_CVMSEG_SIZE=2
+CONFIG_OCTEON_ILM=m
+CONFIG_SMP=y
+CONFIG_NR_CPUS=32
+CONFIG_HZ_100=y
+CONFIG_PCI=y
+CONFIG_PCI_MSI=y
+CONFIG_MIPS32_O32=y
+CONFIG_MIPS32_N32=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_TRANSPARENT_HUGEPAGE=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_MULTIPLE_TABLES=y
+CONFIG_IP_ROUTE_MULTIPATH=y
+CONFIG_IP_ROUTE_VERBOSE=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+CONFIG_IP_MROUTE=y
+CONFIG_IP_PIMSM_V1=y
+CONFIG_IP_PIMSM_V2=y
+CONFIG_SYN_COOKIES=y
+CONFIG_DEVTMPFS=y
+# CONFIG_FW_LOADER is not set
+CONFIG_MTD=y
+# CONFIG_MTD_OF_PARTS is not set
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_SLRAM=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_EEPROM_AT24=y
+CONFIG_EEPROM_AT25=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_ATA=y
+CONFIG_SATA_AHCI=y
+CONFIG_SATA_AHCI_PLATFORM=y
+CONFIG_PATA_OCTEON_CF=y
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_3COM is not set
+# CONFIG_NET_VENDOR_ADAPTEC is not set
+# CONFIG_NET_VENDOR_ALTEON is not set
+# CONFIG_NET_VENDOR_AMD is not set
+# CONFIG_NET_VENDOR_ATHEROS is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_BROCADE is not set
+# CONFIG_NET_VENDOR_CHELSIO is not set
+# CONFIG_NET_VENDOR_CISCO is not set
+# CONFIG_NET_VENDOR_DEC is not set
+# CONFIG_NET_VENDOR_DLINK is not set
+# CONFIG_NET_VENDOR_EMULEX is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MELLANOX is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_MYRI is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_NVIDIA is not set
+# CONFIG_NET_VENDOR_OKI is not set
+# CONFIG_NET_VENDOR_QLOGIC is not set
+# CONFIG_NET_VENDOR_RDC is not set
+# CONFIG_NET_VENDOR_REALTEK is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SILAN is not set
+# CONFIG_NET_VENDOR_SIS is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_SUN is not set
+# CONFIG_NET_VENDOR_TEHUTI is not set
+# CONFIG_NET_VENDOR_TI is not set
+# CONFIG_NET_VENDOR_TOSHIBA is not set
+# CONFIG_NET_VENDOR_VIA is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+CONFIG_BCM87XX_PHY=y
+CONFIG_BROADCOM_PHY=y
+CONFIG_MARVELL_PHY=y
+# CONFIG_WLAN is not set
+# CONFIG_INPUT is not set
+# CONFIG_SERIO is not set
+# CONFIG_VT is not set
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=2
+CONFIG_SERIAL_8250_RUNTIME_UARTS=2
+CONFIG_SERIAL_8250_DW=y
+CONFIG_I2C=y
+CONFIG_I2C_OCTEON=y
+CONFIG_SPI=y
+CONFIG_SPI_OCTEON=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_USB=y
+# CONFIG_USB_PCI is not set
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_HCD_PLATFORM=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_HCD_PLATFORM=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_DWC3=y
+CONFIG_MMC=y
+# CONFIG_PWRSEQ_EMMC is not set
+# CONFIG_PWRSEQ_SIMPLE is not set
+CONFIG_MMC_CAVIUM_OCTEON=y
+CONFIG_EDAC=y
+CONFIG_EDAC_OCTEON_PC=y
+CONFIG_EDAC_OCTEON_L2C=y
+CONFIG_EDAC_OCTEON_LMC=y
+CONFIG_EDAC_OCTEON_PCI=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_DS1307=y
+CONFIG_STAGING=y
+CONFIG_OCTEON_ETHERNET=y
+CONFIG_USB_OCTEON_HCD=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_RAS=y
+CONFIG_EXT4_FS=y
+CONFIG_EXT4_FS_POSIX_ACL=y
+CONFIG_EXT4_FS_SECURITY=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_HUGETLBFS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V4=y
+CONFIG_NFS_V4_1=y
+CONFIG_ROOT_NFS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
+CONFIG_SECURITY=y
+CONFIG_SECURITY_NETWORK=y
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_MD5_OCTEON=y
+CONFIG_CRYPTO_SHA1_OCTEON=m
+CONFIG_CRYPTO_SHA256_OCTEON=m
+CONFIG_CRYPTO_SHA512_OCTEON=m
+CONFIG_CRYPTO_DES=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
+CONFIG_DEBUG_FS=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_SCHED_DEBUG is not set
diff --git a/arch/mips/configs/ci20_defconfig b/arch/mips/configs/ci20_defconfig
new file mode 100644
index 000000000..11f08b6a3
--- /dev/null
+++ b/arch/mips/configs/ci20_defconfig
@@ -0,0 +1,213 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_KERNEL_XZ=y
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_CGROUPS=y
+CONFIG_MEMCG=y
+CONFIG_CGROUP_SCHED=y
+CONFIG_CGROUP_FREEZER=y
+CONFIG_CGROUP_DEVICE=y
+CONFIG_CGROUP_CPUACCT=y
+CONFIG_NAMESPACES=y
+CONFIG_USER_NS=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_KALLSYMS_ALL=y
+CONFIG_EMBEDDED=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_MACH_INGENIC_SOC=y
+CONFIG_JZ4780_CI20=y
+CONFIG_HIGHMEM=y
+CONFIG_HZ_100=y
+# CONFIG_SECCOMP is not set
+# CONFIG_SUSPEND is not set
+CONFIG_MODULES=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+# CONFIG_COMPACTION is not set
+CONFIG_CMA=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+# CONFIG_INET_DIAG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_WIRELESS is not set
+CONFIG_DEVTMPFS=y
+CONFIG_FW_LOADER=m
+# CONFIG_ALLOW_DEV_COREDUMP is not set
+CONFIG_MTD=y
+CONFIG_MTD_RAW_NAND=y
+CONFIG_MTD_NAND_JZ4780=y
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_FASTMAP=y
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_ARC is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+CONFIG_DM9000=y
+CONFIG_DM9000_FORCE_SIMPLE_PHY_POLL=y
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_QUALCOMM is not set
+# CONFIG_NET_VENDOR_ROCKER is not set
+# CONFIG_NET_VENDOR_SAMSUNG is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_VIA is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+# CONFIG_WLAN is not set
+CONFIG_KEYBOARD_GPIO=m
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_LEGACY_PTY_COUNT=2
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=5
+CONFIG_SERIAL_8250_RUNTIME_UARTS=5
+CONFIG_SERIAL_8250_INGENIC=y
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_I2C=y
+CONFIG_I2C_JZ4780=y
+CONFIG_SPI=y
+CONFIG_SPI_GPIO=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_POWER_SUPPLY=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_JZ4740_WDT=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_DEBUG=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_REGULATOR_ACT8865=y
+CONFIG_RC_CORE=m
+CONFIG_LIRC=y
+CONFIG_RC_DEVICES=y
+CONFIG_IR_GPIO_CIR=m
+CONFIG_IR_GPIO_TX=m
+CONFIG_MEDIA_SUPPORT=m
+CONFIG_DRM=m
+CONFIG_DRM_INGENIC=m
+CONFIG_DRM_INGENIC_DW_HDMI=m
+CONFIG_DRM_DISPLAY_CONNECTOR=m
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_FB=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+# CONFIG_HID is not set
+CONFIG_USB=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_DWC2=y
+CONFIG_USB_SERIAL=y
+CONFIG_USB_SERIAL_CH341=y
+CONFIG_USB_GADGET=y
+CONFIG_MMC=y
+CONFIG_MMC_JZ4740=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_ONESHOT=y
+CONFIG_LEDS_TRIGGER_MTD=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_BACKLIGHT=m
+CONFIG_LEDS_TRIGGER_CPU=y
+CONFIG_LEDS_TRIGGER_ACTIVITY=y
+CONFIG_LEDS_TRIGGER_GPIO=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+CONFIG_LEDS_TRIGGER_TRANSIENT=y
+CONFIG_LEDS_TRIGGER_CAMERA=m
+CONFIG_LEDS_TRIGGER_PANIC=y
+CONFIG_LEDS_TRIGGER_NETDEV=y
+CONFIG_LEDS_TRIGGER_PATTERN=y
+CONFIG_LEDS_TRIGGER_AUDIO=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_JZ4740=y
+CONFIG_DMADEVICES=y
+CONFIG_DMA_JZ4780=y
+CONFIG_INGENIC_OST=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_MEMORY=y
+CONFIG_JZ4780_NEMC=y
+CONFIG_PWM=y
+CONFIG_PWM_JZ4740=m
+CONFIG_NVMEM_JZ4780_EFUSE=y
+CONFIG_JZ4770_PHY=y
+CONFIG_EXT4_FS=y
+# CONFIG_DNOTIFY is not set
+CONFIG_AUTOFS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_UTF8=y
+CONFIG_PROC_KCORE=y
+# CONFIG_PROC_PAGE_MONITOR is not set
+CONFIG_TMPFS=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_UBIFS_FS=y
+CONFIG_NFS_FS=y
+CONFIG_ROOT_NFS=y
+CONFIG_NLS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_737=y
+CONFIG_NLS_CODEPAGE_775=y
+CONFIG_NLS_CODEPAGE_850=y
+CONFIG_NLS_CODEPAGE_852=y
+CONFIG_NLS_CODEPAGE_855=y
+CONFIG_NLS_CODEPAGE_857=y
+CONFIG_NLS_CODEPAGE_860=y
+CONFIG_NLS_CODEPAGE_861=y
+CONFIG_NLS_CODEPAGE_862=y
+CONFIG_NLS_CODEPAGE_863=y
+CONFIG_NLS_CODEPAGE_864=y
+CONFIG_NLS_CODEPAGE_865=y
+CONFIG_NLS_CODEPAGE_866=y
+CONFIG_NLS_CODEPAGE_869=y
+CONFIG_NLS_CODEPAGE_936=y
+CONFIG_NLS_CODEPAGE_950=y
+CONFIG_NLS_CODEPAGE_932=y
+CONFIG_NLS_CODEPAGE_949=y
+CONFIG_NLS_CODEPAGE_874=y
+CONFIG_NLS_ISO8859_8=y
+CONFIG_NLS_CODEPAGE_1250=y
+CONFIG_NLS_CODEPAGE_1251=y
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_ISO8859_2=y
+CONFIG_NLS_ISO8859_3=y
+CONFIG_NLS_ISO8859_4=y
+CONFIG_NLS_ISO8859_5=y
+CONFIG_NLS_ISO8859_6=y
+CONFIG_NLS_ISO8859_7=y
+CONFIG_NLS_ISO8859_9=y
+CONFIG_NLS_ISO8859_13=y
+CONFIG_NLS_ISO8859_14=y
+CONFIG_NLS_ISO8859_15=y
+CONFIG_NLS_KOI8_R=y
+CONFIG_NLS_KOI8_U=y
+CONFIG_NLS_UTF8=y
+CONFIG_DMA_CMA=y
+CONFIG_CMA_SIZE_MBYTES=32
+CONFIG_PRINTK_TIME=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_FS=y
+CONFIG_PANIC_ON_OOPS=y
+CONFIG_PANIC_TIMEOUT=10
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_PREEMPT is not set
+CONFIG_STACKTRACE=y
+# CONFIG_FTRACE is not set
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE="earlycon console=ttyS4,115200 clk_ignore_unused"
diff --git a/arch/mips/configs/cobalt_defconfig b/arch/mips/configs/cobalt_defconfig
new file mode 100644
index 000000000..e835730ea
--- /dev/null
+++ b/arch/mips/configs/cobalt_defconfig
@@ -0,0 +1,73 @@
+CONFIG_SYSVIPC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_RELAY=y
+CONFIG_EXPERT=y
+CONFIG_MIPS_COBALT=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_XFRM_USER=y
+CONFIG_NET_KEY=y
+CONFIG_NET_KEY_MIGRATE=y
+CONFIG_INET=y
+# CONFIG_IPV6 is not set
+CONFIG_MTD=y
+CONFIG_MTD_JEDECPROBE=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_PHYSMAP=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_RAID_ATTRS=y
+CONFIG_BLK_DEV_SD=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_ATA=y
+CONFIG_PATA_VIA=y
+CONFIG_NETDEVICES=y
+CONFIG_NET_TULIP=y
+CONFIG_DE2104X=y
+CONFIG_TULIP=y
+CONFIG_INPUT_EVDEV=y
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_MISC=y
+CONFIG_INPUT_COBALT_BTNS=y
+# CONFIG_SERIO is not set
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+# CONFIG_SERIAL_8250_PCI is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_HWMON is not set
+CONFIG_FB=y
+CONFIG_FB_COBALT=y
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_HID=m
+CONFIG_USB=m
+CONFIG_USB_EHCI_HCD=m
+# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+CONFIG_USB_OHCI_HCD=m
+CONFIG_USB_STORAGE=m
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_COBALT_QUBE=y
+CONFIG_LEDS_COBALT_RAQ=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_CMOS=y
+CONFIG_EXT2_FS=y
+CONFIG_EXT2_FS_XATTR=y
+CONFIG_EXT2_FS_POSIX_ACL=y
+CONFIG_EXT2_FS_SECURITY=y
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_POSIX_ACL=y
+CONFIG_EXT3_FS_SECURITY=y
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFSD=y
+CONFIG_NFSD_V3_ACL=y
+CONFIG_LIBCRC32C=y
diff --git a/arch/mips/configs/cu1000-neo_defconfig b/arch/mips/configs/cu1000-neo_defconfig
new file mode 100644
index 000000000..1cbc9302e
--- /dev/null
+++ b/arch/mips/configs/cu1000-neo_defconfig
@@ -0,0 +1,127 @@
+CONFIG_SYSVIPC=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_CGROUPS=y
+CONFIG_MEMCG=y
+CONFIG_CGROUP_SCHED=y
+CONFIG_CGROUP_FREEZER=y
+CONFIG_CGROUP_DEVICE=y
+CONFIG_CGROUP_CPUACCT=y
+CONFIG_NAMESPACES=y
+CONFIG_USER_NS=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_KALLSYMS_ALL=y
+CONFIG_EMBEDDED=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_MACH_INGENIC_SOC=y
+CONFIG_X1000_CU1000_NEO=y
+CONFIG_HIGHMEM=y
+CONFIG_HZ_100=y
+# CONFIG_SECCOMP is not set
+# CONFIG_SUSPEND is not set
+CONFIG_MODULES=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+# CONFIG_COMPACTION is not set
+CONFIG_CMA=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_CFG80211=m
+CONFIG_UEVENT_HELPER=y
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+# CONFIG_ALLOW_DEV_COREDUMP is not set
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_NETDEVICES=y
+CONFIG_STMMAC_ETH=y
+CONFIG_SMSC_PHY=y
+CONFIG_BRCMFMAC=m
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_LEGACY_PTY_COUNT=2
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=3
+CONFIG_SERIAL_8250_RUNTIME_UARTS=3
+CONFIG_SERIAL_8250_INGENIC=y
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_SERIAL_SC16IS7XX=y
+# CONFIG_SERIAL_SC16IS7XX_I2C is not set
+CONFIG_SERIAL_SC16IS7XX_SPI=y
+CONFIG_I2C=y
+CONFIG_I2C_JZ4780=y
+CONFIG_SPI=y
+CONFIG_SPI_INGENIC=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_SENSORS_ADS7828=m
+CONFIG_WATCHDOG=y
+CONFIG_JZ4740_WDT=y
+# CONFIG_VGA_CONSOLE is not set
+# CONFIG_HID is not set
+CONFIG_USB=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_DWC2=y
+CONFIG_USB_SERIAL=y
+CONFIG_USB_SERIAL_CH341=y
+CONFIG_USB_GADGET=y
+CONFIG_MMC=y
+CONFIG_MMC_JZ4740=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_JZ4740=y
+CONFIG_DMADEVICES=y
+CONFIG_DMA_JZ4780=y
+# CONFIG_INGENIC_TIMER is not set
+CONFIG_INGENIC_SYSOST=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_JZ4770_PHY=y
+CONFIG_EXT4_FS=y
+# CONFIG_DNOTIFY is not set
+CONFIG_AUTOFS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_UTF8=y
+CONFIG_PROC_KCORE=y
+# CONFIG_PROC_PAGE_MONITOR is not set
+CONFIG_TMPFS=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_NFS_FS=y
+CONFIG_NLS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_936=y
+CONFIG_NLS_CODEPAGE_950=y
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
+CONFIG_CRYPTO_ECHAINIV=y
+CONFIG_CRYPTO_AES=y
+CONFIG_CRYPTO_DEFLATE=y
+CONFIG_CRYPTO_LZO=y
+CONFIG_PRINTK_TIME=y
+CONFIG_CONSOLE_LOGLEVEL_DEFAULT=15
+CONFIG_CONSOLE_LOGLEVEL_QUIET=15
+CONFIG_MESSAGE_LOGLEVEL_DEFAULT=7
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_FS=y
+CONFIG_PANIC_ON_OOPS=y
+CONFIG_PANIC_TIMEOUT=10
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_PREEMPT is not set
+CONFIG_STACKTRACE=y
+# CONFIG_FTRACE is not set
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE="earlycon clk_ignore_unused"
diff --git a/arch/mips/configs/cu1830-neo_defconfig b/arch/mips/configs/cu1830-neo_defconfig
new file mode 100644
index 000000000..a0f73f3cd
--- /dev/null
+++ b/arch/mips/configs/cu1830-neo_defconfig
@@ -0,0 +1,130 @@
+CONFIG_SYSVIPC=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_CGROUPS=y
+CONFIG_MEMCG=y
+CONFIG_CGROUP_SCHED=y
+CONFIG_CGROUP_FREEZER=y
+CONFIG_CGROUP_DEVICE=y
+CONFIG_CGROUP_CPUACCT=y
+CONFIG_NAMESPACES=y
+CONFIG_USER_NS=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_KALLSYMS_ALL=y
+CONFIG_EMBEDDED=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_MACH_INGENIC_SOC=y
+CONFIG_X1830_CU1830_NEO=y
+CONFIG_HIGHMEM=y
+CONFIG_HZ_100=y
+# CONFIG_SECCOMP is not set
+# CONFIG_SUSPEND is not set
+CONFIG_MODULES=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+# CONFIG_COMPACTION is not set
+CONFIG_CMA=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_CFG80211=m
+CONFIG_UEVENT_HELPER=y
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+# CONFIG_ALLOW_DEV_COREDUMP is not set
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_MD=y
+CONFIG_BLK_DEV_MD=m
+CONFIG_BLK_DEV_DM=m
+CONFIG_NETDEVICES=y
+CONFIG_STMMAC_ETH=y
+CONFIG_ICPLUS_PHY=y
+CONFIG_BRCMFMAC=m
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_LEGACY_PTY_COUNT=2
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=2
+CONFIG_SERIAL_8250_RUNTIME_UARTS=2
+CONFIG_SERIAL_8250_INGENIC=y
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_SERIAL_SC16IS7XX=y
+# CONFIG_SERIAL_SC16IS7XX_I2C is not set
+CONFIG_SERIAL_SC16IS7XX_SPI=y
+CONFIG_I2C=y
+CONFIG_I2C_JZ4780=y
+CONFIG_SPI=y
+CONFIG_SPI_INGENIC=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_SENSORS_ADS7828=m
+CONFIG_WATCHDOG=y
+CONFIG_JZ4740_WDT=y
+# CONFIG_VGA_CONSOLE is not set
+# CONFIG_HID is not set
+CONFIG_USB=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_DWC2=y
+CONFIG_USB_SERIAL=y
+CONFIG_USB_SERIAL_CH341=y
+CONFIG_USB_GADGET=y
+CONFIG_MMC=y
+CONFIG_MMC_JZ4740=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_JZ4740=y
+CONFIG_DMADEVICES=y
+CONFIG_DMA_JZ4780=y
+# CONFIG_INGENIC_TIMER is not set
+CONFIG_INGENIC_SYSOST=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_JZ4770_PHY=y
+CONFIG_EXT4_FS=y
+# CONFIG_DNOTIFY is not set
+CONFIG_AUTOFS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_UTF8=y
+CONFIG_PROC_KCORE=y
+# CONFIG_PROC_PAGE_MONITOR is not set
+CONFIG_TMPFS=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_NFS_FS=y
+CONFIG_NLS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_936=y
+CONFIG_NLS_CODEPAGE_950=y
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
+CONFIG_CRYPTO_ECHAINIV=y
+CONFIG_CRYPTO_AES=y
+CONFIG_CRYPTO_DEFLATE=y
+CONFIG_CRYPTO_LZO=y
+CONFIG_PRINTK_TIME=y
+CONFIG_CONSOLE_LOGLEVEL_DEFAULT=15
+CONFIG_CONSOLE_LOGLEVEL_QUIET=15
+CONFIG_MESSAGE_LOGLEVEL_DEFAULT=7
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_FS=y
+CONFIG_PANIC_ON_OOPS=y
+CONFIG_PANIC_TIMEOUT=10
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_PREEMPT is not set
+CONFIG_STACKTRACE=y
+# CONFIG_FTRACE is not set
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE="earlycon clk_ignore_unused"
diff --git a/arch/mips/configs/db1xxx_defconfig b/arch/mips/configs/db1xxx_defconfig
new file mode 100644
index 000000000..af070be1b
--- /dev/null
+++ b/arch/mips/configs/db1xxx_defconfig
@@ -0,0 +1,224 @@
+CONFIG_LOCALVERSION="-db1xxx"
+CONFIG_KERNEL_XZ=y
+CONFIG_DEFAULT_HOSTNAME="db1xxx"
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_AUDIT=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_LOG_BUF_SHIFT=16
+CONFIG_CGROUPS=y
+CONFIG_MEMCG=y
+CONFIG_BLK_CGROUP=y
+CONFIG_CGROUP_SCHED=y
+CONFIG_CFS_BANDWIDTH=y
+CONFIG_RT_GROUP_SCHED=y
+CONFIG_CGROUP_FREEZER=y
+CONFIG_CGROUP_DEVICE=y
+CONFIG_CGROUP_CPUACCT=y
+CONFIG_KALLSYMS_ALL=y
+CONFIG_EMBEDDED=y
+CONFIG_SLAB=y
+CONFIG_MIPS_ALCHEMY=y
+CONFIG_HZ_100=y
+CONFIG_PCI=y
+CONFIG_PCCARD=y
+CONFIG_PCMCIA_ALCHEMY_DEVBOARD=y
+CONFIG_FIRMWARE_MEMMAP=y
+CONFIG_BLK_DEV_BSGLIB=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_CMA=y
+CONFIG_CMA_DEBUG=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_PACKET_DIAG=y
+CONFIG_UNIX=y
+CONFIG_UNIX_DIAG=y
+CONFIG_XFRM_USER=y
+CONFIG_XFRM_SUB_POLICY=y
+CONFIG_XFRM_MIGRATE=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_FIB_TRIE_STATS=y
+CONFIG_NET_IPIP=y
+CONFIG_NET_IPGRE_DEMUX=y
+CONFIG_NET_IPGRE=y
+CONFIG_NET_IPGRE_BROADCAST=y
+CONFIG_SYN_COOKIES=y
+CONFIG_INET_AH=y
+CONFIG_INET_ESP=y
+CONFIG_INET_IPCOMP=y
+CONFIG_INET_UDP_DIAG=y
+CONFIG_TCP_CONG_ADVANCED=y
+CONFIG_TCP_CONG_VENO=y
+CONFIG_DEFAULT_VENO=y
+CONFIG_IPV6_ROUTER_PREF=y
+CONFIG_IPV6_ROUTE_INFO=y
+CONFIG_IPV6_OPTIMISTIC_DAD=y
+CONFIG_INET6_AH=y
+CONFIG_INET6_ESP=y
+CONFIG_INET6_IPCOMP=y
+CONFIG_IPV6_MIP6=y
+CONFIG_IPV6_VTI=y
+CONFIG_IPV6_SIT_6RD=y
+CONFIG_IPV6_GRE=y
+CONFIG_IPV6_MULTIPLE_TABLES=y
+CONFIG_IPV6_SUBTREES=y
+CONFIG_IPV6_MROUTE=y
+CONFIG_IPV6_MROUTE_MULTIPLE_TABLES=y
+CONFIG_IPV6_PIMSM_V2=y
+CONFIG_BRIDGE=y
+CONFIG_NETLINK_DIAG=y
+CONFIG_BT=y
+CONFIG_BT_RFCOMM=y
+CONFIG_BT_RFCOMM_TTY=y
+CONFIG_BT_BNEP=y
+CONFIG_BT_BNEP_MC_FILTER=y
+CONFIG_BT_BNEP_PROTO_FILTER=y
+CONFIG_BT_HIDP=y
+CONFIG_BT_HCIBTUSB=y
+CONFIG_CFG80211=y
+CONFIG_CFG80211_WEXT=y
+CONFIG_MAC80211=y
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_ADV_OPTIONS=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_SST25L=y
+CONFIG_MTD_RAW_NAND=y
+CONFIG_MTD_NAND_ECC_SW_BCH=y
+CONFIG_MTD_NAND_AU1550=y
+CONFIG_MTD_NAND_PLATFORM=y
+CONFIG_MTD_SPI_NOR=y
+CONFIG_EEPROM_AT24=y
+CONFIG_EEPROM_AT25=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_CHR_DEV_SG=y
+CONFIG_ATA=y
+CONFIG_PATA_HPT37X=y
+CONFIG_PATA_HPT3X2N=y
+CONFIG_PATA_PCMCIA=y
+CONFIG_PATA_PLATFORM=y
+CONFIG_NETDEVICES=y
+CONFIG_NLMON=y
+CONFIG_PCMCIA_3C589=y
+CONFIG_MIPS_AU1X00_ENET=y
+CONFIG_SMC91X=y
+CONFIG_SMSC911X=y
+CONFIG_AMD_PHY=y
+CONFIG_SMSC_PHY=y
+CONFIG_INPUT_EVDEV=y
+CONFIG_KEYBOARD_GPIO=y
+CONFIG_INPUT_TOUCHSCREEN=y
+CONFIG_TOUCHSCREEN_ADS7846=y
+CONFIG_TOUCHSCREEN_WM97XX=y
+CONFIG_INPUT_MISC=y
+CONFIG_INPUT_UINPUT=y
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_TTY_PRINTK=y
+CONFIG_I2C=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_AU1550=y
+CONFIG_SPI=y
+CONFIG_SPI_AU1550=y
+CONFIG_SPI_GPIO=y
+CONFIG_SENSORS_ADM1025=y
+CONFIG_SENSORS_LM70=y
+CONFIG_FB=y
+CONFIG_FB_AU1100=y
+CONFIG_FB_AU1200=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_HRTIMER=y
+CONFIG_SND_DYNAMIC_MINORS=y
+CONFIG_SND_SEQUENCER=y
+CONFIG_SND_AC97_POWER_SAVE=y
+CONFIG_SND_AC97_POWER_SAVE_DEFAULT=1
+CONFIG_SND_SOC=y
+CONFIG_SND_SOC_AU1XPSC=y
+CONFIG_SND_SOC_AU1XAUDIO=y
+CONFIG_SND_SOC_DB1000=y
+CONFIG_SND_SOC_DB1200=y
+CONFIG_HIDRAW=y
+CONFIG_UHID=y
+CONFIG_HID_LOGITECH=y
+CONFIG_HID_LOGITECH_DJ=y
+CONFIG_USB_HIDDEV=y
+CONFIG_USB=y
+CONFIG_USB_DYNAMIC_MINORS=y
+CONFIG_USB_OTG=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_ROOT_HUB_TT=y
+CONFIG_USB_EHCI_HCD_PLATFORM=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_HCD_PLATFORM=y
+CONFIG_USB_STORAGE=y
+CONFIG_MMC=y
+CONFIG_SDIO_UART=y
+CONFIG_MMC_AU1X=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_AU1XXX=y
+CONFIG_EXT4_FS=y
+CONFIG_EXT4_FS_POSIX_ACL=y
+CONFIG_EXT4_FS_SECURITY=y
+CONFIG_XFS_FS=y
+CONFIG_XFS_POSIX_ACL=y
+CONFIG_F2FS_FS=y
+CONFIG_F2FS_FS_SECURITY=y
+CONFIG_FANOTIFY=y
+CONFIG_FUSE_FS=y
+CONFIG_CUSE=y
+CONFIG_VFAT_FS=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_SUMMARY=y
+CONFIG_JFFS2_COMPRESSION_OPTIONS=y
+CONFIG_JFFS2_LZO=y
+CONFIG_JFFS2_RUBIN=y
+CONFIG_SQUASHFS=y
+CONFIG_SQUASHFS_FILE_DIRECT=y
+CONFIG_SQUASHFS_XATTR=y
+CONFIG_SQUASHFS_LZO=y
+CONFIG_SQUASHFS_XZ=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_V4=y
+CONFIG_NFS_V4_1=y
+CONFIG_NFS_V4_2=y
+CONFIG_NFS_V4_1_IMPLEMENTATION_ID_DOMAIN="local"
+CONFIG_NFS_V4_1_MIGRATION=y
+CONFIG_NFSD=y
+CONFIG_NFSD_V3_ACL=y
+CONFIG_NFSD_V4=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_850=y
+CONFIG_NLS_CODEPAGE_852=y
+CONFIG_NLS_CODEPAGE_1250=y
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_ISO8859_2=y
+CONFIG_NLS_ISO8859_15=y
+CONFIG_NLS_UTF8=y
+CONFIG_SECURITYFS=y
+CONFIG_CRYPTO_USER=y
+CONFIG_CRYPTO_CRYPTD=y
+CONFIG_CRYPTO_USER_API_HASH=y
+CONFIG_CRYPTO_USER_API_SKCIPHER=y
+CONFIG_CRC32_SLICEBY4=y
+CONFIG_FONTS=y
+CONFIG_FONT_8x8=y
+CONFIG_MAGIC_SYSRQ=y
diff --git a/arch/mips/configs/decstation_64_defconfig b/arch/mips/configs/decstation_64_defconfig
new file mode 100644
index 000000000..49ec15752
--- /dev/null
+++ b/arch/mips/configs/decstation_64_defconfig
@@ -0,0 +1,213 @@
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_LOG_BUF_SHIFT=15
+CONFIG_EXPERT=y
+# CONFIG_SGETMASK_SYSCALL is not set
+# CONFIG_SYSFS_SYSCALL is not set
+CONFIG_BPF_SYSCALL=y
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_MACH_DECSTATION=y
+CONFIG_64BIT=y
+CONFIG_PAGE_SIZE_16KB=y
+CONFIG_TC=y
+CONFIG_MIPS32_O32=y
+CONFIG_MIPS32_N32=y
+# CONFIG_SUSPEND is not set
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_OSF_PARTITION=y
+# CONFIG_EFI_PARTITION is not set
+CONFIG_TRANSPARENT_HUGEPAGE=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_NET_KEY=m
+CONFIG_NET_KEY_MIGRATE=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_SYN_COOKIES=y
+CONFIG_INET_AH=m
+CONFIG_INET_ESP=m
+CONFIG_INET_IPCOMP=m
+CONFIG_TCP_MD5SIG=y
+CONFIG_IPV6_ROUTER_PREF=y
+CONFIG_IPV6_ROUTE_INFO=y
+CONFIG_INET6_AH=m
+CONFIG_INET6_ESP=m
+CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_MIP6=m
+CONFIG_IPV6_MULTIPLE_TABLES=y
+CONFIG_IPV6_SUBTREES=y
+CONFIG_NETWORK_SECMARK=y
+CONFIG_IP_SCTP=m
+CONFIG_VLAN_8021Q=m
+# CONFIG_WIRELESS is not set
+# CONFIG_UEVENT_HELPER is not set
+# CONFIG_FW_LOADER is not set
+# CONFIG_ALLOW_DEV_COREDUMP is not set
+CONFIG_MTD=m
+CONFIG_MTD_BLOCK=m
+CONFIG_MTD_BLOCK_RO=m
+CONFIG_MTD_MS02NV=m
+CONFIG_BLK_DEV_LOOP=m
+CONFIG_BLK_DEV_RAM=m
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_CHR_DEV_ST=m
+CONFIG_BLK_DEV_SR=m
+CONFIG_CHR_DEV_SG=m
+CONFIG_SCSI_CONSTANTS=y
+CONFIG_SCSI_SPI_ATTRS=m
+CONFIG_ISCSI_TCP=m
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_ALACRITECH is not set
+# CONFIG_NET_VENDOR_AMAZON is not set
+CONFIG_DECLANCE=y
+# CONFIG_NET_VENDOR_AQUANTIA is not set
+# CONFIG_NET_VENDOR_ARC is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_CADENCE is not set
+# CONFIG_NET_VENDOR_CAVIUM is not set
+# CONFIG_NET_VENDOR_CORTINA is not set
+# CONFIG_NET_VENDOR_EZCHIP is not set
+# CONFIG_NET_VENDOR_HUAWEI is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_MICROCHIP is not set
+# CONFIG_NET_VENDOR_MICROSEMI is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_NETRONOME is not set
+# CONFIG_NET_VENDOR_NI is not set
+# CONFIG_NET_VENDOR_QUALCOMM is not set
+# CONFIG_NET_VENDOR_RENESAS is not set
+# CONFIG_NET_VENDOR_ROCKER is not set
+# CONFIG_NET_VENDOR_SAMSUNG is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SOLARFLARE is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_SOCIONEXT is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_SYNOPSYS is not set
+# CONFIG_NET_VENDOR_VIA is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+# CONFIG_NET_VENDOR_XILINX is not set
+CONFIG_FDDI=y
+CONFIG_DEFZA=y
+CONFIG_DEFXX=y
+# CONFIG_WLAN is not set
+# CONFIG_KEYBOARD_ATKBD is not set
+CONFIG_KEYBOARD_LKKBD=y
+# CONFIG_MOUSE_PS2 is not set
+CONFIG_MOUSE_VSXXXAA=y
+# CONFIG_HW_RANDOM is not set
+# CONFIG_HWMON is not set
+CONFIG_FB=y
+CONFIG_FB_TGA=y
+CONFIG_FB_PMAG_AA=y
+CONFIG_FB_PMAG_BA=y
+CONFIG_FB_PMAGB_B=y
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_DUMMY_CONSOLE_COLUMNS=160
+CONFIG_DUMMY_CONSOLE_ROWS=64
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_VGA16 is not set
+# CONFIG_LOGO_LINUX_CLUT224 is not set
+# CONFIG_HID is not set
+# CONFIG_USB_SUPPORT is not set
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_INTF_DEV_UIE_EMUL=y
+CONFIG_RTC_DRV_CMOS=y
+# CONFIG_MIPS_PLATFORM_DEVICES is not set
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_EXT2_FS=y
+CONFIG_EXT2_FS_XATTR=y
+CONFIG_EXT2_FS_POSIX_ACL=y
+CONFIG_EXT2_FS_SECURITY=y
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_POSIX_ACL=y
+CONFIG_EXT3_FS_SECURITY=y
+CONFIG_ISO9660_FS=y
+CONFIG_JOLIET=y
+CONFIG_PROC_KCORE=y
+CONFIG_PROC_CHILDREN=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_HUGETLBFS=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_UFS_FS=y
+CONFIG_UFS_FS_WRITE=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_SWAP=y
+CONFIG_ROOT_NFS=y
+CONFIG_NFSD=m
+CONFIG_NFSD_V3_ACL=y
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+CONFIG_NLS_ISO8859_8=m
+CONFIG_NLS_ASCII=m
+CONFIG_NLS_ISO8859_1=m
+CONFIG_NLS_ISO8859_2=m
+CONFIG_NLS_ISO8859_3=m
+CONFIG_NLS_ISO8859_4=m
+CONFIG_NLS_ISO8859_5=m
+CONFIG_NLS_ISO8859_6=m
+CONFIG_NLS_ISO8859_7=m
+CONFIG_NLS_ISO8859_9=m
+CONFIG_NLS_ISO8859_13=m
+CONFIG_NLS_ISO8859_14=m
+CONFIG_NLS_ISO8859_15=m
+CONFIG_NLS_UTF8=m
+CONFIG_CRYPTO_RSA=m
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_CCM=m
+CONFIG_CRYPTO_GCM=m
+CONFIG_CRYPTO_CHACHA20POLY1305=m
+CONFIG_CRYPTO_CTS=m
+CONFIG_CRYPTO_LRW=m
+CONFIG_CRYPTO_OFB=m
+CONFIG_CRYPTO_PCBC=m
+CONFIG_CRYPTO_XTS=m
+CONFIG_CRYPTO_KEYWRAP=m
+CONFIG_CRYPTO_CMAC=m
+CONFIG_CRYPTO_XCBC=m
+CONFIG_CRYPTO_VMAC=m
+CONFIG_CRYPTO_CRC32=m
+CONFIG_CRYPTO_CRCT10DIF=m
+CONFIG_CRYPTO_MD4=m
+CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_RMD160=m
+CONFIG_CRYPTO_SHA512=m
+CONFIG_CRYPTO_WP512=m
+CONFIG_CRYPTO_ANUBIS=m
+CONFIG_CRYPTO_ARC4=m
+CONFIG_CRYPTO_BLOWFISH=m
+CONFIG_CRYPTO_CAMELLIA=m
+CONFIG_CRYPTO_CAST5=m
+CONFIG_CRYPTO_CAST6=m
+CONFIG_CRYPTO_FCRYPT=m
+CONFIG_CRYPTO_KHAZAD=m
+CONFIG_CRYPTO_SEED=m
+CONFIG_CRYPTO_SERPENT=m
+CONFIG_CRYPTO_TEA=m
+CONFIG_CRYPTO_TWOFISH=m
+CONFIG_CRYPTO_LZO=m
+CONFIG_CRYPTO_842=m
+CONFIG_CRYPTO_LZ4=m
+CONFIG_CRYPTO_LZ4HC=m
+CONFIG_CRYPTO_ANSI_CPRNG=m
+CONFIG_CRYPTO_DRBG_HASH=y
+CONFIG_CRYPTO_DRBG_CTR=y
+# CONFIG_CRYPTO_HW is not set
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_FTRACE is not set
diff --git a/arch/mips/configs/decstation_defconfig b/arch/mips/configs/decstation_defconfig
new file mode 100644
index 000000000..5cec4c096
--- /dev/null
+++ b/arch/mips/configs/decstation_defconfig
@@ -0,0 +1,209 @@
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_LOG_BUF_SHIFT=15
+CONFIG_EXPERT=y
+# CONFIG_SGETMASK_SYSCALL is not set
+# CONFIG_SYSFS_SYSCALL is not set
+CONFIG_BPF_SYSCALL=y
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_MACH_DECSTATION=y
+CONFIG_CPU_R3000=y
+CONFIG_TC=y
+# CONFIG_SUSPEND is not set
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_OSF_PARTITION=y
+# CONFIG_EFI_PARTITION is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_NET_KEY=m
+CONFIG_NET_KEY_MIGRATE=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_SYN_COOKIES=y
+CONFIG_INET_AH=m
+CONFIG_INET_ESP=m
+CONFIG_INET_IPCOMP=m
+CONFIG_TCP_MD5SIG=y
+CONFIG_IPV6_ROUTER_PREF=y
+CONFIG_IPV6_ROUTE_INFO=y
+CONFIG_INET6_AH=m
+CONFIG_INET6_ESP=m
+CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_MIP6=m
+CONFIG_IPV6_MULTIPLE_TABLES=y
+CONFIG_IPV6_SUBTREES=y
+CONFIG_NETWORK_SECMARK=y
+CONFIG_IP_SCTP=m
+CONFIG_VLAN_8021Q=m
+# CONFIG_WIRELESS is not set
+# CONFIG_UEVENT_HELPER is not set
+# CONFIG_FW_LOADER is not set
+# CONFIG_ALLOW_DEV_COREDUMP is not set
+CONFIG_MTD=m
+CONFIG_MTD_BLOCK=m
+CONFIG_MTD_BLOCK_RO=m
+CONFIG_MTD_MS02NV=m
+CONFIG_BLK_DEV_LOOP=m
+CONFIG_BLK_DEV_RAM=m
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_CHR_DEV_ST=m
+CONFIG_BLK_DEV_SR=m
+CONFIG_CHR_DEV_SG=m
+CONFIG_SCSI_CONSTANTS=y
+CONFIG_SCSI_SPI_ATTRS=m
+CONFIG_ISCSI_TCP=m
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_ALACRITECH is not set
+# CONFIG_NET_VENDOR_AMAZON is not set
+CONFIG_DECLANCE=y
+# CONFIG_NET_VENDOR_AQUANTIA is not set
+# CONFIG_NET_VENDOR_ARC is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_CADENCE is not set
+# CONFIG_NET_VENDOR_CAVIUM is not set
+# CONFIG_NET_VENDOR_CORTINA is not set
+# CONFIG_NET_VENDOR_EZCHIP is not set
+# CONFIG_NET_VENDOR_HUAWEI is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_MICROCHIP is not set
+# CONFIG_NET_VENDOR_MICROSEMI is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_NETRONOME is not set
+# CONFIG_NET_VENDOR_NI is not set
+# CONFIG_NET_VENDOR_QUALCOMM is not set
+# CONFIG_NET_VENDOR_RENESAS is not set
+# CONFIG_NET_VENDOR_ROCKER is not set
+# CONFIG_NET_VENDOR_SAMSUNG is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SOLARFLARE is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_SOCIONEXT is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_SYNOPSYS is not set
+# CONFIG_NET_VENDOR_VIA is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+# CONFIG_NET_VENDOR_XILINX is not set
+CONFIG_FDDI=y
+CONFIG_DEFZA=y
+CONFIG_DEFXX=y
+# CONFIG_WLAN is not set
+# CONFIG_KEYBOARD_ATKBD is not set
+CONFIG_KEYBOARD_LKKBD=y
+# CONFIG_MOUSE_PS2 is not set
+CONFIG_MOUSE_VSXXXAA=y
+# CONFIG_HW_RANDOM is not set
+# CONFIG_HWMON is not set
+CONFIG_FB=y
+CONFIG_FB_TGA=y
+CONFIG_FB_PMAG_AA=y
+CONFIG_FB_PMAG_BA=y
+CONFIG_FB_PMAGB_B=y
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_DUMMY_CONSOLE_COLUMNS=160
+CONFIG_DUMMY_CONSOLE_ROWS=64
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_VGA16 is not set
+# CONFIG_LOGO_LINUX_CLUT224 is not set
+# CONFIG_HID is not set
+# CONFIG_USB_SUPPORT is not set
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_INTF_DEV_UIE_EMUL=y
+CONFIG_RTC_DRV_CMOS=y
+# CONFIG_MIPS_PLATFORM_DEVICES is not set
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_EXT2_FS=y
+CONFIG_EXT2_FS_XATTR=y
+CONFIG_EXT2_FS_POSIX_ACL=y
+CONFIG_EXT2_FS_SECURITY=y
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_POSIX_ACL=y
+CONFIG_EXT3_FS_SECURITY=y
+CONFIG_ISO9660_FS=y
+CONFIG_JOLIET=y
+CONFIG_PROC_KCORE=y
+CONFIG_PROC_CHILDREN=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_UFS_FS=y
+CONFIG_UFS_FS_WRITE=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_SWAP=y
+CONFIG_ROOT_NFS=y
+CONFIG_NFSD=m
+CONFIG_NFSD_V3_ACL=y
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+CONFIG_NLS_ISO8859_8=m
+CONFIG_NLS_ASCII=m
+CONFIG_NLS_ISO8859_1=m
+CONFIG_NLS_ISO8859_2=m
+CONFIG_NLS_ISO8859_3=m
+CONFIG_NLS_ISO8859_4=m
+CONFIG_NLS_ISO8859_5=m
+CONFIG_NLS_ISO8859_6=m
+CONFIG_NLS_ISO8859_7=m
+CONFIG_NLS_ISO8859_9=m
+CONFIG_NLS_ISO8859_13=m
+CONFIG_NLS_ISO8859_14=m
+CONFIG_NLS_ISO8859_15=m
+CONFIG_NLS_UTF8=m
+CONFIG_CRYPTO_RSA=m
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_CCM=m
+CONFIG_CRYPTO_GCM=m
+CONFIG_CRYPTO_CHACHA20POLY1305=m
+CONFIG_CRYPTO_CTS=m
+CONFIG_CRYPTO_LRW=m
+CONFIG_CRYPTO_OFB=m
+CONFIG_CRYPTO_PCBC=m
+CONFIG_CRYPTO_XTS=m
+CONFIG_CRYPTO_KEYWRAP=m
+CONFIG_CRYPTO_CMAC=m
+CONFIG_CRYPTO_XCBC=m
+CONFIG_CRYPTO_VMAC=m
+CONFIG_CRYPTO_CRC32=m
+CONFIG_CRYPTO_CRCT10DIF=m
+CONFIG_CRYPTO_MD4=m
+CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_RMD160=m
+CONFIG_CRYPTO_SHA512=m
+CONFIG_CRYPTO_WP512=m
+CONFIG_CRYPTO_ANUBIS=m
+CONFIG_CRYPTO_ARC4=m
+CONFIG_CRYPTO_BLOWFISH=m
+CONFIG_CRYPTO_CAMELLIA=m
+CONFIG_CRYPTO_CAST5=m
+CONFIG_CRYPTO_CAST6=m
+CONFIG_CRYPTO_FCRYPT=m
+CONFIG_CRYPTO_KHAZAD=m
+CONFIG_CRYPTO_SEED=m
+CONFIG_CRYPTO_SERPENT=m
+CONFIG_CRYPTO_TEA=m
+CONFIG_CRYPTO_TWOFISH=m
+CONFIG_CRYPTO_LZO=m
+CONFIG_CRYPTO_842=m
+CONFIG_CRYPTO_LZ4=m
+CONFIG_CRYPTO_LZ4HC=m
+CONFIG_CRYPTO_ANSI_CPRNG=m
+CONFIG_CRYPTO_DRBG_HASH=y
+CONFIG_CRYPTO_DRBG_CTR=y
+# CONFIG_CRYPTO_HW is not set
+CONFIG_FRAME_WARN=2048
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_FTRACE is not set
diff --git a/arch/mips/configs/decstation_r4k_defconfig b/arch/mips/configs/decstation_r4k_defconfig
new file mode 100644
index 000000000..af37e26d9
--- /dev/null
+++ b/arch/mips/configs/decstation_r4k_defconfig
@@ -0,0 +1,209 @@
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_LOG_BUF_SHIFT=15
+CONFIG_EXPERT=y
+# CONFIG_SGETMASK_SYSCALL is not set
+# CONFIG_SYSFS_SYSCALL is not set
+CONFIG_BPF_SYSCALL=y
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_MACH_DECSTATION=y
+CONFIG_TC=y
+# CONFIG_SUSPEND is not set
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_OSF_PARTITION=y
+# CONFIG_EFI_PARTITION is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_NET_KEY=m
+CONFIG_NET_KEY_MIGRATE=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_SYN_COOKIES=y
+CONFIG_INET_AH=m
+CONFIG_INET_ESP=m
+CONFIG_INET_IPCOMP=m
+CONFIG_TCP_MD5SIG=y
+CONFIG_IPV6_ROUTER_PREF=y
+CONFIG_IPV6_ROUTE_INFO=y
+CONFIG_INET6_AH=m
+CONFIG_INET6_ESP=m
+CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_MIP6=m
+CONFIG_IPV6_MULTIPLE_TABLES=y
+CONFIG_IPV6_SUBTREES=y
+CONFIG_NETWORK_SECMARK=y
+CONFIG_IP_SCTP=m
+CONFIG_VLAN_8021Q=m
+# CONFIG_WIRELESS is not set
+# CONFIG_UEVENT_HELPER is not set
+# CONFIG_FW_LOADER is not set
+# CONFIG_ALLOW_DEV_COREDUMP is not set
+CONFIG_MTD=m
+CONFIG_MTD_BLOCK=m
+CONFIG_MTD_BLOCK_RO=m
+CONFIG_MTD_MS02NV=m
+CONFIG_BLK_DEV_LOOP=m
+CONFIG_BLK_DEV_RAM=m
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_CHR_DEV_ST=m
+CONFIG_BLK_DEV_SR=m
+CONFIG_CHR_DEV_SG=m
+CONFIG_SCSI_CONSTANTS=y
+CONFIG_SCSI_SPI_ATTRS=m
+CONFIG_ISCSI_TCP=m
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_ALACRITECH is not set
+# CONFIG_NET_VENDOR_AMAZON is not set
+CONFIG_DECLANCE=y
+# CONFIG_NET_VENDOR_AQUANTIA is not set
+# CONFIG_NET_VENDOR_ARC is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_CADENCE is not set
+# CONFIG_NET_VENDOR_CAVIUM is not set
+# CONFIG_NET_VENDOR_CORTINA is not set
+# CONFIG_NET_VENDOR_EZCHIP is not set
+# CONFIG_NET_VENDOR_HUAWEI is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_MICROCHIP is not set
+# CONFIG_NET_VENDOR_MICROSEMI is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_NETRONOME is not set
+# CONFIG_NET_VENDOR_NI is not set
+# CONFIG_NET_VENDOR_QUALCOMM is not set
+# CONFIG_NET_VENDOR_RENESAS is not set
+# CONFIG_NET_VENDOR_ROCKER is not set
+# CONFIG_NET_VENDOR_SAMSUNG is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SOLARFLARE is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_SOCIONEXT is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_SYNOPSYS is not set
+# CONFIG_NET_VENDOR_VIA is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+# CONFIG_NET_VENDOR_XILINX is not set
+CONFIG_FDDI=y
+CONFIG_DEFZA=y
+CONFIG_DEFXX=y
+# CONFIG_WLAN is not set
+# CONFIG_KEYBOARD_ATKBD is not set
+CONFIG_KEYBOARD_LKKBD=y
+# CONFIG_MOUSE_PS2 is not set
+CONFIG_MOUSE_VSXXXAA=y
+# CONFIG_SERIAL_DZ is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_HWMON is not set
+CONFIG_FB=y
+CONFIG_FB_TGA=y
+CONFIG_FB_PMAG_AA=y
+CONFIG_FB_PMAG_BA=y
+CONFIG_FB_PMAGB_B=y
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_DUMMY_CONSOLE_COLUMNS=160
+CONFIG_DUMMY_CONSOLE_ROWS=64
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_VGA16 is not set
+# CONFIG_LOGO_LINUX_CLUT224 is not set
+# CONFIG_HID is not set
+# CONFIG_USB_SUPPORT is not set
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_INTF_DEV_UIE_EMUL=y
+CONFIG_RTC_DRV_CMOS=y
+# CONFIG_MIPS_PLATFORM_DEVICES is not set
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_EXT2_FS=y
+CONFIG_EXT2_FS_XATTR=y
+CONFIG_EXT2_FS_POSIX_ACL=y
+CONFIG_EXT2_FS_SECURITY=y
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_POSIX_ACL=y
+CONFIG_EXT3_FS_SECURITY=y
+CONFIG_ISO9660_FS=y
+CONFIG_JOLIET=y
+CONFIG_PROC_KCORE=y
+CONFIG_PROC_CHILDREN=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_UFS_FS=y
+CONFIG_UFS_FS_WRITE=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_SWAP=y
+CONFIG_ROOT_NFS=y
+CONFIG_NFSD=m
+CONFIG_NFSD_V3_ACL=y
+# CONFIG_RPCSEC_GSS_KRB5 is not set
+CONFIG_NLS_ISO8859_8=m
+CONFIG_NLS_ASCII=m
+CONFIG_NLS_ISO8859_1=m
+CONFIG_NLS_ISO8859_2=m
+CONFIG_NLS_ISO8859_3=m
+CONFIG_NLS_ISO8859_4=m
+CONFIG_NLS_ISO8859_5=m
+CONFIG_NLS_ISO8859_6=m
+CONFIG_NLS_ISO8859_7=m
+CONFIG_NLS_ISO8859_9=m
+CONFIG_NLS_ISO8859_13=m
+CONFIG_NLS_ISO8859_14=m
+CONFIG_NLS_ISO8859_15=m
+CONFIG_NLS_UTF8=m
+CONFIG_CRYPTO_RSA=m
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_CCM=m
+CONFIG_CRYPTO_GCM=m
+CONFIG_CRYPTO_CHACHA20POLY1305=m
+CONFIG_CRYPTO_CTS=m
+CONFIG_CRYPTO_LRW=m
+CONFIG_CRYPTO_OFB=m
+CONFIG_CRYPTO_PCBC=m
+CONFIG_CRYPTO_XTS=m
+CONFIG_CRYPTO_KEYWRAP=m
+CONFIG_CRYPTO_CMAC=m
+CONFIG_CRYPTO_XCBC=m
+CONFIG_CRYPTO_VMAC=m
+CONFIG_CRYPTO_CRC32=m
+CONFIG_CRYPTO_CRCT10DIF=m
+CONFIG_CRYPTO_MD4=m
+CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_RMD160=m
+CONFIG_CRYPTO_SHA512=m
+CONFIG_CRYPTO_WP512=m
+CONFIG_CRYPTO_ANUBIS=m
+CONFIG_CRYPTO_ARC4=m
+CONFIG_CRYPTO_BLOWFISH=m
+CONFIG_CRYPTO_CAMELLIA=m
+CONFIG_CRYPTO_CAST5=m
+CONFIG_CRYPTO_CAST6=m
+CONFIG_CRYPTO_FCRYPT=m
+CONFIG_CRYPTO_KHAZAD=m
+CONFIG_CRYPTO_SEED=m
+CONFIG_CRYPTO_SERPENT=m
+CONFIG_CRYPTO_TEA=m
+CONFIG_CRYPTO_TWOFISH=m
+CONFIG_CRYPTO_LZO=m
+CONFIG_CRYPTO_842=m
+CONFIG_CRYPTO_LZ4=m
+CONFIG_CRYPTO_LZ4HC=m
+CONFIG_CRYPTO_ANSI_CPRNG=m
+CONFIG_CRYPTO_DRBG_HASH=y
+CONFIG_CRYPTO_DRBG_CTR=y
+# CONFIG_CRYPTO_HW is not set
+CONFIG_FRAME_WARN=2048
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_FTRACE is not set
diff --git a/arch/mips/configs/fuloong2e_defconfig b/arch/mips/configs/fuloong2e_defconfig
new file mode 100644
index 000000000..843d6a5a4
--- /dev/null
+++ b/arch/mips/configs/fuloong2e_defconfig
@@ -0,0 +1,224 @@
+CONFIG_LOCALVERSION="-fuloong2e"
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT_VOLUNTARY=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_NAMESPACES=y
+CONFIG_USER_NS=y
+CONFIG_EXPERT=y
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_PROFILING=y
+CONFIG_MACH_LOONGSON2EF=y
+CONFIG_PCI=y
+CONFIG_MIPS32_O32=y
+CONFIG_MIPS32_N32=y
+# CONFIG_SUSPEND is not set
+CONFIG_HIBERNATION=y
+CONFIG_PM_STD_PARTITION="/dev/sda3"
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_BINFMT_MISC=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_NET_IPIP=m
+# CONFIG_INET_DIAG is not set
+# CONFIG_IPV6 is not set
+CONFIG_NETFILTER=y
+CONFIG_NETFILTER_NETLINK_LOG=m
+CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
+CONFIG_NETFILTER_XT_TARGET_MARK=m
+CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_TARGET_TRACE=m
+CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP=m
+CONFIG_NETFILTER_XT_MATCH_COMMENT=m
+CONFIG_NETFILTER_XT_MATCH_DCCP=m
+CONFIG_NETFILTER_XT_MATCH_ESP=m
+CONFIG_NETFILTER_XT_MATCH_IPRANGE=m
+CONFIG_NETFILTER_XT_MATCH_LENGTH=m
+CONFIG_NETFILTER_XT_MATCH_LIMIT=m
+CONFIG_NETFILTER_XT_MATCH_MAC=m
+CONFIG_NETFILTER_XT_MATCH_MARK=m
+CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_OWNER=m
+CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
+CONFIG_NETFILTER_XT_MATCH_QUOTA=m
+CONFIG_NETFILTER_XT_MATCH_RATEEST=m
+CONFIG_NETFILTER_XT_MATCH_REALM=m
+CONFIG_NETFILTER_XT_MATCH_RECENT=m
+CONFIG_NETFILTER_XT_MATCH_SCTP=m
+CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
+CONFIG_NETFILTER_XT_MATCH_STRING=m
+CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
+CONFIG_NETFILTER_XT_MATCH_TIME=m
+CONFIG_NETFILTER_XT_MATCH_U32=m
+CONFIG_IP_NF_IPTABLES=m
+CONFIG_IP_NF_MATCH_AH=m
+CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_TTL=m
+CONFIG_IP_NF_FILTER=m
+CONFIG_IP_NF_TARGET_REJECT=m
+CONFIG_IP_NF_MANGLE=m
+CONFIG_IP_NF_TARGET_ECN=m
+CONFIG_IP_NF_TARGET_TTL=m
+CONFIG_IP_NF_RAW=m
+CONFIG_IP_NF_ARPTABLES=m
+CONFIG_IP_NF_ARPFILTER=m
+CONFIG_IP_NF_ARP_MANGLE=m
+CONFIG_PHONET=m
+CONFIG_NET_9P=m
+CONFIG_FW_LOADER=m
+CONFIG_MTD=m
+CONFIG_MTD_BLOCK=m
+CONFIG_MTD_CFI=m
+CONFIG_MTD_JEDECPROBE=m
+CONFIG_MTD_CFI_ADV_OPTIONS=y
+CONFIG_MTD_CFI_AMDSTD=m
+CONFIG_MTD_CFI_STAA=m
+CONFIG_MTD_PHYSMAP=m
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=m
+CONFIG_CDROM_PKTCDVD=m
+CONFIG_ATA_OVER_ETH=m
+CONFIG_BLK_DEV_SD=y
+CONFIG_BLK_DEV_SR=y
+CONFIG_CHR_DEV_SG=y
+CONFIG_SCSI_CONSTANTS=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_ATA=y
+CONFIG_PATA_VIA=y
+CONFIG_ATA_GENERIC=y
+CONFIG_PATA_LEGACY=y
+CONFIG_NETDEVICES=y
+CONFIG_NET_FC=y
+CONFIG_MACVLAN=m
+CONFIG_VETH=m
+CONFIG_8139TOO=y
+# CONFIG_8139TOO_PIO is not set
+CONFIG_PHYLIB=m
+CONFIG_CICADA_PHY=m
+CONFIG_DAVICOM_PHY=m
+CONFIG_LXT_PHY=m
+CONFIG_MARVELL_PHY=m
+CONFIG_QSEMI_PHY=m
+CONFIG_PPP=m
+CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_FILTER=y
+CONFIG_PPP_MPPE=m
+CONFIG_PPP_MULTILINK=y
+CONFIG_PPPOE=m
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
+CONFIG_SLIP=m
+CONFIG_SLIP_COMPRESSED=y
+CONFIG_SLIP_SMART=y
+CONFIG_SLIP_MODE_SLIP6=y
+CONFIG_INPUT_FF_MEMLESS=y
+CONFIG_MOUSE_SERIAL=y
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=2
+CONFIG_SERIAL_8250_RUNTIME_UARTS=2
+CONFIG_HW_RANDOM=y
+CONFIG_I2C=m
+CONFIG_I2C_CHARDEV=m
+CONFIG_I2C_VIAPRO=m
+# CONFIG_HWMON is not set
+CONFIG_FB=y
+CONFIG_FB_RADEON=y
+# CONFIG_FB_RADEON_I2C is not set
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_SOUND=y
+CONFIG_SND=m
+CONFIG_SND_SEQUENCER=m
+CONFIG_SND_SEQ_DUMMY=m
+CONFIG_SND_VIA82XX=m
+CONFIG_HIDRAW=y
+# CONFIG_USB_HID is not set
+CONFIG_HID_PID=y
+CONFIG_USB_KBD=y
+CONFIG_USB_MOUSE=y
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_OTG_PRODUCTLIST=y
+CONFIG_USB_C67X00_HCD=m
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_ROOT_HUB_TT=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_UHCI_HCD=m
+CONFIG_USB_R8A66597_HCD=m
+CONFIG_USB_ACM=y
+CONFIG_USB_PRINTER=y
+CONFIG_USB_WDM=m
+CONFIG_USB_TMC=m
+CONFIG_USB_STORAGE=y
+CONFIG_USB_STORAGE_ONETOUCH=y
+CONFIG_USB_STORAGE_CYPRESS_ATACB=y
+CONFIG_USB_ISP1760=m
+CONFIG_USB_SEVSEG=m
+CONFIG_USB_ISIGHTFW=m
+CONFIG_UIO=m
+CONFIG_UIO_CIF=m
+CONFIG_EXT2_FS=y
+CONFIG_EXT3_FS=y
+CONFIG_EXT4_FS_POSIX_ACL=y
+CONFIG_EXT4_FS_SECURITY=y
+CONFIG_REISERFS_FS=m
+CONFIG_AUTOFS4_FS=y
+CONFIG_FUSE_FS=y
+CONFIG_ISO9660_FS=m
+CONFIG_JOLIET=y
+CONFIG_ZISOFS=y
+CONFIG_UDF_FS=m
+CONFIG_MSDOS_FS=m
+CONFIG_VFAT_FS=m
+CONFIG_FAT_DEFAULT_CODEPAGE=936
+CONFIG_FAT_DEFAULT_IOCHARSET="utf8"
+CONFIG_NTFS_FS=m
+CONFIG_NTFS_RW=y
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_OMFS_FS=m
+CONFIG_NFS_FS=m
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_V4=m
+CONFIG_NFSD=m
+CONFIG_NFSD_V3_ACL=y
+CONFIG_NFSD_V4=y
+CONFIG_CIFS=m
+CONFIG_CIFS_STATS2=y
+CONFIG_CIFS_XATTR=y
+CONFIG_CIFS_POSIX=y
+CONFIG_CIFS_DEBUG2=y
+CONFIG_NLS_DEFAULT="utf8"
+CONFIG_NLS_CODEPAGE_936=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
+CONFIG_CRYPTO_AUTHENC=m
+CONFIG_CRYPTO_GCM=m
+CONFIG_CRYPTO_CTS=m
+CONFIG_CRYPTO_PCBC=m
+CONFIG_CRYPTO_XTS=m
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_RMD160=m
+CONFIG_CRYPTO_SEED=m
+CONFIG_CRYPTO_DEFLATE=m
+CONFIG_CRYPTO_LZO=m
+# CONFIG_CRYPTO_HW is not set
+CONFIG_CRC_CCITT=y
+CONFIG_CRC7=m
diff --git a/arch/mips/configs/gcw0_defconfig b/arch/mips/configs/gcw0_defconfig
new file mode 100644
index 000000000..460683b52
--- /dev/null
+++ b/arch/mips/configs/gcw0_defconfig
@@ -0,0 +1,151 @@
+CONFIG_DEFAULT_HOSTNAME="gcw0"
+CONFIG_NO_HZ_IDLE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT_VOLUNTARY=y
+CONFIG_EMBEDDED=y
+CONFIG_PROFILING=y
+CONFIG_MACH_INGENIC_SOC=y
+CONFIG_JZ4770_GCW0=y
+CONFIG_HIGHMEM=y
+# CONFIG_SECCOMP is not set
+CONFIG_MIPS_RAW_APPENDED_DTB=y
+CONFIG_MIPS_CMDLINE_DTB_EXTEND=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BOUNCE is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_CFG80211=y
+CONFIG_MAC80211=m
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_LOOP_MIN_COUNT=0
+CONFIG_NETDEVICES=y
+# CONFIG_ETHERNET is not set
+# CONFIG_WLAN_VENDOR_ADMTEK is not set
+# CONFIG_WLAN_VENDOR_ATH is not set
+# CONFIG_WLAN_VENDOR_ATMEL is not set
+# CONFIG_WLAN_VENDOR_BROADCOM is not set
+# CONFIG_WLAN_VENDOR_CISCO is not set
+# CONFIG_WLAN_VENDOR_INTEL is not set
+# CONFIG_WLAN_VENDOR_INTERSIL is not set
+# CONFIG_WLAN_VENDOR_MARVELL is not set
+# CONFIG_WLAN_VENDOR_MEDIATEK is not set
+# CONFIG_WLAN_VENDOR_RALINK is not set
+CONFIG_RTL8192CU=m
+# CONFIG_RTLWIFI_DEBUG is not set
+# CONFIG_WLAN_VENDOR_RSI is not set
+# CONFIG_WLAN_VENDOR_ST is not set
+# CONFIG_WLAN_VENDOR_TI is not set
+# CONFIG_WLAN_VENDOR_ZYDAS is not set
+# CONFIG_WLAN_VENDOR_QUANTENNA is not set
+CONFIG_INPUT_EVDEV=y
+# CONFIG_KEYBOARD_ATKBD is not set
+CONFIG_KEYBOARD_GPIO=y
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_JOYSTICK=y
+CONFIG_INPUT_MISC=y
+CONFIG_INPUT_UINPUT=y
+CONFIG_INPUT_PWM_VIBRA=y
+# CONFIG_SERIO is not set
+CONFIG_SERIAL_8250=y
+# CONFIG_SERIAL_8250_DEPRECATED_OPTIONS is not set
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_INGENIC=y
+CONFIG_HW_RANDOM=y
+CONFIG_I2C_GPIO=y
+CONFIG_SPI=y
+CONFIG_SPI_GPIO=y
+CONFIG_POWER_SUPPLY=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_JZ4740_WDT=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_REGULATOR_ACT8865=y
+CONFIG_DRM=y
+CONFIG_DRM_FBDEV_OVERALLOC=300
+CONFIG_DRM_PANEL_NOVATEK_NT39016=y
+CONFIG_DRM_INGENIC=y
+CONFIG_DRM_ETNAVIV=y
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+CONFIG_BACKLIGHT_PWM=y
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+# CONFIG_LOGO_LINUX_VGA16 is not set
+CONFIG_SOUND=y
+CONFIG_SND=y
+# CONFIG_SND_SUPPORT_OLD_API is not set
+# CONFIG_SND_PROC_FS is not set
+# CONFIG_SND_DRIVERS is not set
+# CONFIG_SND_SPI is not set
+# CONFIG_SND_MIPS is not set
+# CONFIG_SND_USB is not set
+CONFIG_SND_SOC=y
+CONFIG_SND_JZ4740_SOC_I2S=y
+CONFIG_SND_SOC_JZ4770_CODEC=y
+CONFIG_SND_SOC_SIMPLE_AMPLIFIER=y
+CONFIG_SND_SIMPLE_CARD=y
+CONFIG_USB_CONN_GPIO=y
+CONFIG_USB=y
+CONFIG_USB_OTG=y
+CONFIG_USB_OTG_DISABLE_EXTERNAL_HUB=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_HCD_PLATFORM=y
+CONFIG_USB_MUSB_HDRC=y
+CONFIG_USB_MUSB_GADGET=y
+CONFIG_USB_MUSB_JZ4740=y
+CONFIG_USB_INVENTRA_DMA=y
+CONFIG_JZ4770_PHY=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_VBUS_DRAW=500
+CONFIG_USB_ETH=y
+CONFIG_MMC=y
+# CONFIG_PWRSEQ_EMMC is not set
+# CONFIG_PWRSEQ_SIMPLE is not set
+CONFIG_MMC_JZ4740=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+CONFIG_LEDS_TRIGGER_PANIC=y
+CONFIG_RTC_CLASS=y
+# CONFIG_RTC_NVMEM is not set
+CONFIG_RTC_DRV_JZ4740=y
+CONFIG_DMADEVICES=y
+CONFIG_DMA_JZ4780=y
+# CONFIG_VIRTIO_MENU is not set
+CONFIG_STAGING=y
+CONFIG_R8188EU=m
+CONFIG_INGENIC_OST=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_IIO=y
+CONFIG_IIO_BUFFER=y
+CONFIG_IIO_BUFFER_CB=y
+CONFIG_IIO_KFIFO_BUF=y
+CONFIG_MXC6255=m
+CONFIG_INGENIC_ADC=y
+CONFIG_PWM=y
+CONFIG_PWM_JZ4740=y
+CONFIG_EXT4_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_SQUASHFS=y
+CONFIG_SQUASHFS_FILE_DIRECT=y
+CONFIG_SQUASHFS_DECOMP_MULTI=y
+# CONFIG_NETWORK_FILESYSTEMS is not set
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
+CONFIG_LSM="lockdown,yama,loadpin,safesetid,integrity"
+CONFIG_CRYPTO_ECHAINIV=y
+CONFIG_FONTS=y
+CONFIG_FONT_6x10=y
+CONFIG_DEBUG_FS=y
diff --git a/arch/mips/configs/generic/32r1.config b/arch/mips/configs/generic/32r1.config
new file mode 100644
index 000000000..a11cd8715
--- /dev/null
+++ b/arch/mips/configs/generic/32r1.config
@@ -0,0 +1,2 @@
+CONFIG_CPU_MIPS32_R1=y
+CONFIG_HIGHMEM=y
diff --git a/arch/mips/configs/generic/32r2.config b/arch/mips/configs/generic/32r2.config
new file mode 100644
index 000000000..9570672d4
--- /dev/null
+++ b/arch/mips/configs/generic/32r2.config
@@ -0,0 +1,3 @@
+CONFIG_CPU_MIPS32_R2=y
+CONFIG_MIPS_O32_FP64_SUPPORT=y
+CONFIG_HIGHMEM=y
diff --git a/arch/mips/configs/generic/32r6.config b/arch/mips/configs/generic/32r6.config
new file mode 100644
index 000000000..1a5d5ea4a
--- /dev/null
+++ b/arch/mips/configs/generic/32r6.config
@@ -0,0 +1,4 @@
+CONFIG_CPU_MIPS32_R6=y
+CONFIG_HIGHMEM=y
+
+CONFIG_CRYPTO_CRC32_MIPS=y
diff --git a/arch/mips/configs/generic/64r1.config b/arch/mips/configs/generic/64r1.config
new file mode 100644
index 000000000..7c1ea7e7b
--- /dev/null
+++ b/arch/mips/configs/generic/64r1.config
@@ -0,0 +1,4 @@
+CONFIG_CPU_MIPS64_R1=y
+CONFIG_64BIT=y
+CONFIG_MIPS32_O32=y
+CONFIG_MIPS32_N32=y
diff --git a/arch/mips/configs/generic/64r2.config b/arch/mips/configs/generic/64r2.config
new file mode 100644
index 000000000..b4d31ae8b
--- /dev/null
+++ b/arch/mips/configs/generic/64r2.config
@@ -0,0 +1,5 @@
+CONFIG_CPU_MIPS64_R2=y
+CONFIG_MIPS_O32_FP64_SUPPORT=y
+CONFIG_64BIT=y
+CONFIG_MIPS32_O32=y
+CONFIG_MIPS32_N32=y
diff --git a/arch/mips/configs/generic/64r6.config b/arch/mips/configs/generic/64r6.config
new file mode 100644
index 000000000..5dd8e8503
--- /dev/null
+++ b/arch/mips/configs/generic/64r6.config
@@ -0,0 +1,6 @@
+CONFIG_CPU_MIPS64_R6=y
+CONFIG_64BIT=y
+CONFIG_MIPS32_O32=y
+CONFIG_MIPS32_N32=y
+
+CONFIG_CRYPTO_CRC32_MIPS=y
diff --git a/arch/mips/configs/generic/board-boston.config b/arch/mips/configs/generic/board-boston.config
new file mode 100644
index 000000000..19560a45b
--- /dev/null
+++ b/arch/mips/configs/generic/board-boston.config
@@ -0,0 +1,48 @@
+CONFIG_FIT_IMAGE_FDT_BOSTON=y
+
+CONFIG_ATA=y
+CONFIG_SATA_AHCI=y
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+
+CONFIG_AUXDISPLAY=y
+CONFIG_IMG_ASCII_LCD=y
+
+CONFIG_COMMON_CLK_BOSTON=y
+
+CONFIG_DMADEVICES=y
+CONFIG_PCH_DMA=y
+
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_GPIO_PCH=y
+
+CONFIG_I2C=y
+CONFIG_I2C_EG20T=y
+
+CONFIG_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PCI=y
+
+CONFIG_NETDEVICES=y
+CONFIG_PCH_GBE=y
+
+CONFIG_PCI=y
+CONFIG_PCI_MSI=y
+CONFIG_PCIE_XILINX=y
+
+CONFIG_PCH_PHUB=y
+
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_M41T80=y
+
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_OF_PLATFORM=y
+
+CONFIG_SPI=y
+CONFIG_SPI_TOPCLIFF_PCH=y
+
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_OHCI_HCD=y
diff --git a/arch/mips/configs/generic/board-marduk.config b/arch/mips/configs/generic/board-marduk.config
new file mode 100644
index 000000000..05ca34cd5
--- /dev/null
+++ b/arch/mips/configs/generic/board-marduk.config
@@ -0,0 +1,53 @@
+CONFIG_FIT_IMAGE_FDT_MARDUK=y
+
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+
+CONFIG_CLKSRC_PISTACHIO=y
+
+CONFIG_COMMON_CLK_PISTACHIO=y
+
+CONFIG_DMADEVICES=y
+CONFIG_IMG_MDC_DMA=y
+
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_GPIO_PCH=y
+
+CONFIG_I2C=y
+CONFIG_I2C_IMG=y
+
+CONFIG_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_DW=y
+CONFIG_MMC_DW_PLTFM=y
+
+CONFIG_NETDEVICES=y
+CONFIG_STMMAC_ETH=y
+CONFIG_STMMAC_PLATFORM=y
+
+CONFIG_PHY_PISTACHIO_USB=y
+
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_PISTACHIO=y
+
+CONFIG_RESET_PISTACHIO=y
+
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_SERIAL_8250_DW=y
+
+CONFIG_SPI=y
+CONFIG_SRAM=y
+
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_DWC2=y
+
+CONFIG_CRYPTO_DEV_IMGTEC_HASH=y
+CONFIG_IMGPDC_WDT=y
+CONFIG_IR_IMG=y
+CONFIG_CC10001_ADC=y
+CONFIG_SND_SOC_IMG=y
diff --git a/arch/mips/configs/generic/board-ni169445.config b/arch/mips/configs/generic/board-ni169445.config
new file mode 100644
index 000000000..fc3580e4e
--- /dev/null
+++ b/arch/mips/configs/generic/board-ni169445.config
@@ -0,0 +1,29 @@
+# require CONFIG_CPU_MIPS32_R2=y
+# require CONFIG_CPU_LITTLE_ENDIAN=y
+
+CONFIG_FIT_IMAGE_FDT_NI169445=y
+
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_OF_PLATFORM=y
+
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_GPIO_GENERIC_PLATFORM=y
+
+CONFIG_MTD=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CMDLINE_PARTS=y
+
+CONFIG_MTD_NAND_ECC_SW_HAMMING=y
+CONFIG_MTD_NAND_ECC_SW_BCH=y
+CONFIG_MTD_RAW_NAND=y
+CONFIG_MTD_NAND_GPIO=y
+
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_BLOCK=y
+
+CONFIG_NETDEVICES=y
+CONFIG_STMMAC_ETH=y
+CONFIG_STMMAC_PLATFORM=y
+CONFIG_DWMAC_GENERIC=y
diff --git a/arch/mips/configs/generic/board-ocelot.config b/arch/mips/configs/generic/board-ocelot.config
new file mode 100644
index 000000000..8cfbafa53
--- /dev/null
+++ b/arch/mips/configs/generic/board-ocelot.config
@@ -0,0 +1,50 @@
+# require CONFIG_CPU_MIPS32_R2=y
+
+CONFIG_LEGACY_BOARD_OCELOT=y
+CONFIG_FIT_IMAGE_FDT_OCELOT=y
+
+CONFIG_BRIDGE=y
+CONFIG_GENERIC_PHY=y
+
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_RAW_NAND=y
+CONFIG_MTD_NAND_PLATFORM=y
+CONFIG_MTD_SPI_NOR=y
+CONFIG_MTD_UBI=y
+
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_OF_PLATFORM=y
+
+CONFIG_NETDEVICES=y
+CONFIG_NET_SWITCHDEV=y
+CONFIG_NET_DSA=y
+CONFIG_MSCC_OCELOT_SWITCH=y
+CONFIG_MDIO_MSCC_MIIM=y
+CONFIG_MICROSEMI_PHY=y
+
+CONFIG_I2C=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_MUX=y
+CONFIG_I2C_DESIGNWARE_PLATFORM=y
+
+CONFIG_SPI=y
+CONFIG_SPI_BITBANG=y
+CONFIG_SPI_DESIGNWARE=y
+CONFIG_SPI_DW_MMIO=y
+CONFIG_SPI_SPIDEV=y
+
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_OCELOT=y
+
+CONFIG_GPIO_SYSFS=y
+
+CONFIG_POWER_RESET=y
+CONFIG_POWER_RESET_OCELOT_RESET=y
+
+CONFIG_MAGIC_SYSRQ=y
diff --git a/arch/mips/configs/generic/board-ranchu.config b/arch/mips/configs/generic/board-ranchu.config
new file mode 100644
index 000000000..640aac845
--- /dev/null
+++ b/arch/mips/configs/generic/board-ranchu.config
@@ -0,0 +1,29 @@
+CONFIG_VIRT_BOARD_RANCHU=y
+
+CONFIG_BATTERY_GOLDFISH=y
+CONFIG_FB=y
+CONFIG_FB_GOLDFISH=y
+CONFIG_GOLDFISH=y
+CONFIG_STAGING=y
+CONFIG_GOLDFISH_PIC=y
+CONFIG_GOLDFISH_PIPE=y
+CONFIG_GOLDFISH_TTY=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_GOLDFISH=y
+
+CONFIG_INPUT_EVDEV=y
+CONFIG_INPUT_KEYBOARD=y
+CONFIG_KEYBOARD_GOLDFISH_EVENTS=y
+
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_POWER_SUPPLY=y
+CONFIG_POWER_RESET=y
+CONFIG_POWER_RESET_SYSCON=y
+CONFIG_POWER_RESET_SYSCON_POWEROFF=y
+
+CONFIG_VIRTIO_BLK=y
+CONFIG_VIRTIO_CONSOLE=y
+CONFIG_VIRTIO_MMIO=y
+CONFIG_VIRTIO_MMIO_CMDLINE_DEVICES=y
+CONFIG_NETDEVICES=y
+CONFIG_VIRTIO_NET=y
diff --git a/arch/mips/configs/generic/board-sead-3.config b/arch/mips/configs/generic/board-sead-3.config
new file mode 100644
index 000000000..df49a592d
--- /dev/null
+++ b/arch/mips/configs/generic/board-sead-3.config
@@ -0,0 +1,34 @@
+# require CONFIG_32BIT=y
+
+CONFIG_LEGACY_BOARD_SEAD3=y
+
+CONFIG_AUXDISPLAY=y
+CONFIG_IMG_ASCII_LCD=y
+
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_SYSCON=y
+
+CONFIG_MMC=y
+CONFIG_MMC_SPI=y
+
+CONFIG_MTD=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_OF_PARTS=y
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_PHYSMAP_OF=y
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_GLUEBI=y
+
+CONFIG_NETDEVICES=y
+CONFIG_SMSC911X=y
+CONFIG_SMSC_PHY=y
+
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_OF_PLATFORM=y
+
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
diff --git a/arch/mips/configs/generic/board-xilfpga.config b/arch/mips/configs/generic/board-xilfpga.config
new file mode 100644
index 000000000..9cce57385
--- /dev/null
+++ b/arch/mips/configs/generic/board-xilfpga.config
@@ -0,0 +1,22 @@
+# require CONFIG_CPU_MIPS32_R2=y
+# require CONFIG_CPU_LITTLE_ENDIAN=y
+
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_GPIO_XILINX=y
+CONFIG_PANIC_ON_OOPS=y
+CONFIG_FIT_IMAGE_FDT_XILFPGA=y
+CONFIG_I2C=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_XILINX=y
+CONFIG_SENSORS_ADT7410=y
+CONFIG_TMPFS=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_NETDEVICES=y
+CONFIG_XILINX_EMACLITE=y
+CONFIG_SMSC_PHY=y
diff --git a/arch/mips/configs/generic/eb.config b/arch/mips/configs/generic/eb.config
new file mode 100644
index 000000000..c5cdc99a6
--- /dev/null
+++ b/arch/mips/configs/generic/eb.config
@@ -0,0 +1 @@
+CONFIG_CPU_BIG_ENDIAN=y
diff --git a/arch/mips/configs/generic/el.config b/arch/mips/configs/generic/el.config
new file mode 100644
index 000000000..ee43fdb3b
--- /dev/null
+++ b/arch/mips/configs/generic/el.config
@@ -0,0 +1 @@
+CONFIG_CPU_LITTLE_ENDIAN=y
diff --git a/arch/mips/configs/generic/micro32r2.config b/arch/mips/configs/generic/micro32r2.config
new file mode 100644
index 000000000..b701fe7aa
--- /dev/null
+++ b/arch/mips/configs/generic/micro32r2.config
@@ -0,0 +1,4 @@
+CONFIG_CPU_MIPS32_R2=y
+CONFIG_CPU_MICROMIPS=y
+CONFIG_MIPS_O32_FP64_SUPPORT=y
+CONFIG_HIGHMEM=y
diff --git a/arch/mips/configs/generic_defconfig b/arch/mips/configs/generic_defconfig
new file mode 100644
index 000000000..c2cd2b181
--- /dev/null
+++ b/arch/mips/configs/generic_defconfig
@@ -0,0 +1,91 @@
+CONFIG_SYSVIPC=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_MEMCG=y
+CONFIG_BLK_CGROUP=y
+CONFIG_CFS_BANDWIDTH=y
+CONFIG_RT_GROUP_SCHED=y
+CONFIG_CGROUP_PIDS=y
+CONFIG_CGROUP_FREEZER=y
+CONFIG_CPUSETS=y
+CONFIG_CGROUP_DEVICE=y
+CONFIG_CGROUP_CPUACCT=y
+CONFIG_NAMESPACES=y
+CONFIG_USER_NS=y
+CONFIG_SCHED_AUTOGROUP=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_BPF_SYSCALL=y
+CONFIG_USERFAULTFD=y
+CONFIG_EMBEDDED=y
+# CONFIG_SLUB_DEBUG is not set
+# CONFIG_COMPAT_BRK is not set
+CONFIG_CPU_LITTLE_ENDIAN=y
+CONFIG_MIPS_CPS=y
+CONFIG_HIGHMEM=y
+CONFIG_NR_CPUS=16
+CONFIG_MIPS_O32_FP64_SUPPORT=y
+CONFIG_JUMP_LABEL=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_TRIM_UNUSED_KSYMS=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_NETFILTER=y
+# CONFIG_WIRELESS is not set
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+CONFIG_SCSI=y
+CONFIG_HW_RANDOM=y
+# CONFIG_HWMON is not set
+CONFIG_MFD_SYSCON=y
+CONFIG_HID_A4TECH=y
+CONFIG_HID_APPLE=y
+CONFIG_HID_BELKIN=y
+CONFIG_HID_CHERRY=y
+CONFIG_HID_CHICONY=y
+CONFIG_HID_CYPRESS=y
+CONFIG_HID_EZKEY=y
+CONFIG_HID_KENSINGTON=y
+CONFIG_HID_LOGITECH=y
+CONFIG_HID_MICROSOFT=y
+CONFIG_HID_MONTEREY=y
+# CONFIG_MIPS_PLATFORM_DEVICES is not set
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_EXT4_FS=y
+CONFIG_EXT4_FS_POSIX_ACL=y
+CONFIG_EXT4_FS_SECURITY=y
+CONFIG_FS_ENCRYPTION=y
+CONFIG_FANOTIFY=y
+CONFIG_FUSE_FS=y
+CONFIG_CUSE=y
+CONFIG_OVERLAY_FS=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+# CONFIG_MISC_FILESYSTEMS is not set
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_V4=y
+CONFIG_NFS_V4_1=y
+CONFIG_NFS_V4_2=y
+CONFIG_ROOT_NFS=y
+# CONFIG_XZ_DEC_X86 is not set
+# CONFIG_XZ_DEC_POWERPC is not set
+# CONFIG_XZ_DEC_IA64 is not set
+# CONFIG_XZ_DEC_ARM is not set
+# CONFIG_XZ_DEC_ARMTHUMB is not set
+# CONFIG_XZ_DEC_SPARC is not set
+CONFIG_PRINTK_TIME=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
+CONFIG_DEBUG_INFO_REDUCED=y
+CONFIG_DEBUG_FS=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_FTRACE is not set
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE="earlycon"
diff --git a/arch/mips/configs/gpr_defconfig b/arch/mips/configs/gpr_defconfig
new file mode 100644
index 000000000..eb755650f
--- /dev/null
+++ b/arch/mips/configs/gpr_defconfig
@@ -0,0 +1,295 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT_VOLUNTARY=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_RELAY=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_EXPERT=y
+CONFIG_SLAB=y
+CONFIG_PROFILING=y
+CONFIG_MIPS_ALCHEMY=y
+CONFIG_MIPS_GPR=y
+CONFIG_PCI=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_BINFMT_MISC=m
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_MULTIPLE_TABLES=y
+CONFIG_IP_ROUTE_MULTIPATH=y
+CONFIG_IP_ROUTE_VERBOSE=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_SYN_COOKIES=y
+# CONFIG_IPV6 is not set
+CONFIG_NETWORK_SECMARK=y
+CONFIG_NETFILTER=y
+CONFIG_NETFILTER_NETLINK_LOG=m
+CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
+CONFIG_NETFILTER_XT_TARGET_DSCP=m
+CONFIG_NETFILTER_XT_TARGET_MARK=m
+CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_TARGET_SECMARK=m
+CONFIG_NETFILTER_XT_MATCH_COMMENT=m
+CONFIG_NETFILTER_XT_MATCH_DSCP=m
+CONFIG_NETFILTER_XT_MATCH_ESP=m
+CONFIG_NETFILTER_XT_MATCH_LENGTH=m
+CONFIG_NETFILTER_XT_MATCH_LIMIT=m
+CONFIG_NETFILTER_XT_MATCH_MAC=m
+CONFIG_NETFILTER_XT_MATCH_MARK=m
+CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_PHYSDEV=m
+CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
+CONFIG_NETFILTER_XT_MATCH_QUOTA=m
+CONFIG_NETFILTER_XT_MATCH_REALM=m
+CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
+CONFIG_NETFILTER_XT_MATCH_STRING=m
+CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
+CONFIG_IP_NF_IPTABLES=m
+CONFIG_IP_NF_MATCH_AH=m
+CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_TTL=m
+CONFIG_IP_NF_FILTER=m
+CONFIG_IP_NF_TARGET_REJECT=m
+CONFIG_IP_NF_MANGLE=m
+CONFIG_IP_NF_TARGET_ECN=m
+CONFIG_IP_NF_TARGET_TTL=m
+CONFIG_IP_NF_RAW=m
+CONFIG_IP_NF_ARPTABLES=m
+CONFIG_IP_NF_ARPFILTER=m
+CONFIG_IP_NF_ARP_MANGLE=m
+CONFIG_BRIDGE_NF_EBTABLES=m
+CONFIG_BRIDGE_EBT_BROUTE=m
+CONFIG_BRIDGE_EBT_T_FILTER=m
+CONFIG_BRIDGE_EBT_T_NAT=m
+CONFIG_BRIDGE_EBT_802_3=m
+CONFIG_BRIDGE_EBT_AMONG=m
+CONFIG_BRIDGE_EBT_ARP=m
+CONFIG_BRIDGE_EBT_IP=m
+CONFIG_BRIDGE_EBT_LIMIT=m
+CONFIG_BRIDGE_EBT_MARK=m
+CONFIG_BRIDGE_EBT_PKTTYPE=m
+CONFIG_BRIDGE_EBT_STP=m
+CONFIG_BRIDGE_EBT_VLAN=m
+CONFIG_BRIDGE_EBT_ARPREPLY=m
+CONFIG_BRIDGE_EBT_DNAT=m
+CONFIG_BRIDGE_EBT_MARK_T=m
+CONFIG_BRIDGE_EBT_REDIRECT=m
+CONFIG_BRIDGE_EBT_SNAT=m
+CONFIG_BRIDGE_EBT_LOG=m
+CONFIG_IP_DCCP=m
+CONFIG_IP_SCTP=m
+CONFIG_TIPC=m
+CONFIG_ATM=y
+CONFIG_ATM_CLIP=y
+CONFIG_ATM_LANE=m
+CONFIG_ATM_MPOA=m
+CONFIG_ATM_BR2684=m
+CONFIG_BRIDGE=m
+CONFIG_VLAN_8021Q=m
+CONFIG_LLC2=m
+CONFIG_ATALK=m
+CONFIG_DEV_APPLETALK=m
+CONFIG_IPDDP=m
+CONFIG_IPDDP_ENCAP=y
+CONFIG_X25=m
+CONFIG_LAPB=m
+CONFIG_NET_SCHED=y
+CONFIG_NET_SCH_CBQ=m
+CONFIG_NET_SCH_HTB=m
+CONFIG_NET_SCH_HFSC=m
+CONFIG_NET_SCH_ATM=m
+CONFIG_NET_SCH_PRIO=m
+CONFIG_NET_SCH_RED=m
+CONFIG_NET_SCH_SFQ=m
+CONFIG_NET_SCH_TEQL=m
+CONFIG_NET_SCH_TBF=m
+CONFIG_NET_SCH_GRED=m
+CONFIG_NET_SCH_DSMARK=m
+CONFIG_NET_SCH_NETEM=m
+CONFIG_NET_SCH_INGRESS=m
+CONFIG_NET_CLS_BASIC=m
+CONFIG_NET_CLS_TCINDEX=m
+CONFIG_NET_CLS_ROUTE4=m
+CONFIG_NET_CLS_FW=m
+CONFIG_NET_CLS_U32=m
+CONFIG_CLS_U32_MARK=y
+CONFIG_NET_CLS_RSVP=m
+CONFIG_NET_CLS_RSVP6=m
+CONFIG_NET_EMATCH=y
+CONFIG_NET_EMATCH_CMP=m
+CONFIG_NET_EMATCH_NBYTE=m
+CONFIG_NET_EMATCH_U32=m
+CONFIG_NET_EMATCH_META=m
+CONFIG_NET_EMATCH_TEXT=m
+CONFIG_NET_CLS_ACT=y
+CONFIG_NET_ACT_POLICE=y
+CONFIG_NET_PKTGEN=m
+CONFIG_HAMRADIO=y
+CONFIG_AX25=m
+# CONFIG_AX25_DAMA_SLAVE is not set
+CONFIG_NETROM=m
+CONFIG_ROSE=m
+CONFIG_MKISS=m
+CONFIG_6PACK=m
+CONFIG_BPQETHER=m
+CONFIG_BAYCOM_SER_FDX=m
+CONFIG_BAYCOM_SER_HDX=m
+CONFIG_YAM=m
+CONFIG_CFG80211=y
+CONFIG_MAC80211=y
+CONFIG_MTD=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_RAM=m
+CONFIG_MTD_COMPLEX_MAPPINGS=y
+CONFIG_MTD_PHYSMAP=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_SIZE=65536
+CONFIG_TIFM_CORE=m
+CONFIG_SCSI=m
+CONFIG_BLK_DEV_SD=m
+CONFIG_CHR_DEV_SG=m
+CONFIG_SCSI_LOGGING=y
+CONFIG_SCSI_SPI_ATTRS=m
+CONFIG_SCSI_FC_ATTRS=m
+CONFIG_SCSI_ISCSI_ATTRS=m
+CONFIG_SCSI_SAS_LIBSAS=m
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_NETDEVICES=y
+CONFIG_NET_FC=y
+CONFIG_NETCONSOLE=m
+CONFIG_ATM_TCP=m
+CONFIG_ATM_LANAI=m
+CONFIG_ATM_ENI=m
+CONFIG_ATM_NICSTAR=m
+CONFIG_ATM_IDT77252=m
+CONFIG_ATM_IA=m
+CONFIG_ATM_FORE200E=m
+CONFIG_ATM_HE=m
+CONFIG_ATM_HE_USE_SUNI=y
+CONFIG_MIPS_AU1X00_ENET=y
+CONFIG_CICADA_PHY=m
+CONFIG_DAVICOM_PHY=m
+CONFIG_LXT_PHY=m
+CONFIG_MARVELL_PHY=m
+CONFIG_QSEMI_PHY=m
+CONFIG_SMSC_PHY=m
+CONFIG_VITESSE_PHY=m
+CONFIG_PPP=m
+CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_FILTER=y
+CONFIG_PPP_MPPE=m
+CONFIG_PPP_MULTILINK=y
+CONFIG_PPPOATM=m
+CONFIG_PPPOE=m
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
+CONFIG_SLIP=m
+CONFIG_SLIP_COMPRESSED=y
+CONFIG_SLIP_SMART=y
+CONFIG_SLIP_MODE_SLIP6=y
+CONFIG_ATH_DEBUG=y
+CONFIG_ATH5K=y
+CONFIG_ATH5K_DEBUG=y
+CONFIG_WAN=y
+CONFIG_HDLC=m
+CONFIG_HDLC_RAW=m
+CONFIG_HDLC_RAW_ETH=m
+CONFIG_HDLC_CISCO=m
+CONFIG_HDLC_FR=m
+CONFIG_HDLC_PPP=m
+CONFIG_HDLC_X25=m
+CONFIG_PCI200SYN=m
+CONFIG_WANXL=m
+CONFIG_FARSYNC=m
+CONFIG_LAPBETHER=m
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+# CONFIG_SERIAL_8250_PCI is not set
+CONFIG_HW_RANDOM=y
+CONFIG_I2C=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_GPIO=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_SENSORS_LM83=y
+CONFIG_WATCHDOG=y
+CONFIG_WATCHDOG_NOWAYOUT=y
+CONFIG_SSB=m
+CONFIG_SSB_DRIVER_PCICORE=y
+# CONFIG_VGA_ARB is not set
+# CONFIG_LCD_CLASS_DEVICE is not set
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_USB_HID=m
+CONFIG_USB_HIDDEV=y
+CONFIG_USB_KBD=m
+CONFIG_USB_MOUSE=m
+CONFIG_USB=y
+CONFIG_USB_MON=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_ROOT_HUB_TT=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_HCD_PLATFORM=y
+CONFIG_USB_STORAGE=m
+CONFIG_USB_SERIAL=y
+CONFIG_USB_SERIAL_GENERIC=y
+CONFIG_USB_SERIAL_SIERRAWIRELESS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+# CONFIG_DNOTIFY is not set
+# CONFIG_INOTIFY_USER is not set
+CONFIG_ISO9660_FS=m
+CONFIG_JOLIET=y
+CONFIG_ZISOFS=y
+CONFIG_UDF_FS=m
+CONFIG_MSDOS_FS=m
+CONFIG_VFAT_FS=m
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_COMPRESSION_OPTIONS=y
+CONFIG_JFFS2_RUBIN=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V4=y
+CONFIG_ROOT_NFS=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_850=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_CRYPTO_AUTHENC=m
+CONFIG_CRYPTO_TEST=m
+CONFIG_CRYPTO_PCBC=m
+CONFIG_CRYPTO_MD4=m
+CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_SHA512=m
+CONFIG_CRYPTO_WP512=m
+CONFIG_CRYPTO_ANUBIS=m
+CONFIG_CRYPTO_BLOWFISH=m
+CONFIG_CRYPTO_CAST5=m
+CONFIG_CRYPTO_CAST6=m
+CONFIG_CRYPTO_KHAZAD=m
+CONFIG_CRYPTO_SERPENT=m
+CONFIG_CRYPTO_TEA=m
+CONFIG_CRYPTO_TWOFISH=m
+CONFIG_CRYPTO_DEFLATE=m
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE="console=ttyS0,115200 root=/dev/nfs rw ip=auto"
diff --git a/arch/mips/configs/ip22_defconfig b/arch/mips/configs/ip22_defconfig
new file mode 100644
index 000000000..13df29901
--- /dev/null
+++ b/arch/mips/configs/ip22_defconfig
@@ -0,0 +1,334 @@
+CONFIG_SYSVIPC=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT_VOLUNTARY=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_NAMESPACES=y
+CONFIG_USER_NS=y
+CONFIG_RELAY=y
+CONFIG_EXPERT=y
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_SGI_IP22=y
+CONFIG_ARC_CONSOLE=y
+CONFIG_CPU_R5000=y
+CONFIG_HZ_1000=y
+# CONFIG_SUSPEND is not set
+CONFIG_PM=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_BINFMT_MISC=m
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_XFRM_USER=m
+CONFIG_NET_KEY=y
+CONFIG_NET_KEY_MIGRATE=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_INET_AH=m
+CONFIG_INET_ESP=m
+CONFIG_INET_IPCOMP=m
+CONFIG_TCP_MD5SIG=y
+CONFIG_IPV6_ROUTER_PREF=y
+CONFIG_IPV6_ROUTE_INFO=y
+CONFIG_IPV6_OPTIMISTIC_DAD=y
+CONFIG_INET6_AH=m
+CONFIG_INET6_ESP=m
+CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_MIP6=m
+CONFIG_IPV6_TUNNEL=m
+CONFIG_IPV6_MULTIPLE_TABLES=y
+CONFIG_IPV6_SUBTREES=y
+CONFIG_IPV6_MROUTE=y
+CONFIG_IPV6_PIMSM_V2=y
+CONFIG_NETWORK_SECMARK=y
+CONFIG_NETFILTER=y
+CONFIG_NF_CONNTRACK=m
+CONFIG_NF_CONNTRACK_SECMARK=y
+CONFIG_NF_CONNTRACK_EVENTS=y
+CONFIG_NF_CONNTRACK_AMANDA=m
+CONFIG_NF_CONNTRACK_FTP=m
+CONFIG_NF_CONNTRACK_H323=m
+CONFIG_NF_CONNTRACK_IRC=m
+CONFIG_NF_CONNTRACK_PPTP=m
+CONFIG_NF_CONNTRACK_SANE=m
+CONFIG_NF_CONNTRACK_SIP=m
+CONFIG_NF_CONNTRACK_TFTP=m
+CONFIG_NF_CT_NETLINK=m
+CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
+CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
+CONFIG_NETFILTER_XT_TARGET_CONNSECMARK=m
+CONFIG_NETFILTER_XT_TARGET_DSCP=m
+CONFIG_NETFILTER_XT_TARGET_MARK=m
+CONFIG_NETFILTER_XT_TARGET_NFLOG=m
+CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_TARGET_TPROXY=m
+CONFIG_NETFILTER_XT_TARGET_TRACE=m
+CONFIG_NETFILTER_XT_TARGET_SECMARK=m
+CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
+CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP=m
+CONFIG_NETFILTER_XT_MATCH_COMMENT=m
+CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
+CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
+CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
+CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+CONFIG_NETFILTER_XT_MATCH_DCCP=m
+CONFIG_NETFILTER_XT_MATCH_DSCP=m
+CONFIG_NETFILTER_XT_MATCH_ESP=m
+CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
+CONFIG_NETFILTER_XT_MATCH_HELPER=m
+CONFIG_NETFILTER_XT_MATCH_IPRANGE=m
+CONFIG_NETFILTER_XT_MATCH_LENGTH=m
+CONFIG_NETFILTER_XT_MATCH_LIMIT=m
+CONFIG_NETFILTER_XT_MATCH_MAC=m
+CONFIG_NETFILTER_XT_MATCH_MARK=m
+CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_OWNER=m
+CONFIG_NETFILTER_XT_MATCH_POLICY=m
+CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
+CONFIG_NETFILTER_XT_MATCH_QUOTA=m
+CONFIG_NETFILTER_XT_MATCH_RATEEST=m
+CONFIG_NETFILTER_XT_MATCH_REALM=m
+CONFIG_NETFILTER_XT_MATCH_RECENT=m
+CONFIG_NETFILTER_XT_MATCH_SOCKET=m
+CONFIG_NETFILTER_XT_MATCH_STATE=m
+CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
+CONFIG_NETFILTER_XT_MATCH_STRING=m
+CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
+CONFIG_NETFILTER_XT_MATCH_TIME=m
+CONFIG_NETFILTER_XT_MATCH_U32=m
+CONFIG_IP_VS=m
+CONFIG_IP_VS_IPV6=y
+CONFIG_IP_VS_PROTO_TCP=y
+CONFIG_IP_VS_PROTO_UDP=y
+CONFIG_IP_VS_PROTO_ESP=y
+CONFIG_IP_VS_PROTO_AH=y
+CONFIG_IP_VS_RR=m
+CONFIG_IP_VS_WRR=m
+CONFIG_IP_VS_LC=m
+CONFIG_IP_VS_WLC=m
+CONFIG_IP_VS_LBLC=m
+CONFIG_IP_VS_LBLCR=m
+CONFIG_IP_VS_DH=m
+CONFIG_IP_VS_SH=m
+CONFIG_IP_VS_SED=m
+CONFIG_IP_VS_NQ=m
+CONFIG_IP_NF_IPTABLES=m
+CONFIG_IP_NF_MATCH_AH=m
+CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_TTL=m
+CONFIG_IP_NF_FILTER=m
+CONFIG_IP_NF_TARGET_REJECT=m
+CONFIG_IP_NF_MANGLE=m
+CONFIG_IP_NF_TARGET_CLUSTERIP=m
+CONFIG_IP_NF_TARGET_ECN=m
+CONFIG_IP_NF_TARGET_TTL=m
+CONFIG_IP_NF_RAW=m
+CONFIG_IP_NF_ARPTABLES=m
+CONFIG_IP_NF_ARPFILTER=m
+CONFIG_IP_NF_ARP_MANGLE=m
+CONFIG_IP6_NF_MATCH_AH=m
+CONFIG_IP6_NF_MATCH_EUI64=m
+CONFIG_IP6_NF_MATCH_FRAG=m
+CONFIG_IP6_NF_MATCH_OPTS=m
+CONFIG_IP6_NF_MATCH_HL=m
+CONFIG_IP6_NF_MATCH_IPV6HEADER=m
+CONFIG_IP6_NF_MATCH_MH=m
+CONFIG_IP6_NF_MATCH_RT=m
+CONFIG_IP6_NF_TARGET_HL=m
+CONFIG_IP6_NF_FILTER=m
+CONFIG_IP6_NF_TARGET_REJECT=m
+CONFIG_IP6_NF_MANGLE=m
+CONFIG_IP6_NF_RAW=m
+CONFIG_PHONET=m
+CONFIG_NET_SCHED=y
+CONFIG_NET_SCH_CBQ=m
+CONFIG_NET_SCH_HTB=m
+CONFIG_NET_SCH_HFSC=m
+CONFIG_NET_SCH_PRIO=m
+CONFIG_NET_SCH_RED=m
+CONFIG_NET_SCH_SFQ=m
+CONFIG_NET_SCH_TEQL=m
+CONFIG_NET_SCH_TBF=m
+CONFIG_NET_SCH_GRED=m
+CONFIG_NET_SCH_DSMARK=m
+CONFIG_NET_SCH_NETEM=m
+CONFIG_NET_SCH_INGRESS=m
+CONFIG_NET_CLS_BASIC=m
+CONFIG_NET_CLS_TCINDEX=m
+CONFIG_NET_CLS_ROUTE4=m
+CONFIG_NET_CLS_FW=m
+CONFIG_NET_CLS_U32=m
+CONFIG_NET_CLS_RSVP=m
+CONFIG_NET_CLS_RSVP6=m
+CONFIG_NET_CLS_FLOW=m
+CONFIG_NET_CLS_ACT=y
+CONFIG_NET_ACT_POLICE=y
+CONFIG_NET_ACT_GACT=m
+CONFIG_GACT_PROB=y
+CONFIG_NET_ACT_MIRRED=m
+CONFIG_NET_ACT_IPT=m
+CONFIG_NET_ACT_NAT=m
+CONFIG_NET_ACT_PEDIT=m
+CONFIG_NET_ACT_SIMP=m
+CONFIG_NET_ACT_SKBEDIT=m
+CONFIG_RFKILL=m
+CONFIG_CONNECTOR=m
+CONFIG_CDROM_PKTCDVD=m
+CONFIG_ATA_OVER_ETH=m
+CONFIG_RAID_ATTRS=m
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_CHR_DEV_ST=y
+CONFIG_BLK_DEV_SR=y
+CONFIG_CHR_DEV_SCH=m
+CONFIG_SCSI_CONSTANTS=y
+CONFIG_SCSI_SCAN_ASYNC=y
+CONFIG_SCSI_SPI_ATTRS=m
+CONFIG_ISCSI_TCP=m
+CONFIG_SGIWD93_SCSI=y
+CONFIG_NETDEVICES=y
+CONFIG_BONDING=m
+CONFIG_DUMMY=m
+CONFIG_EQUALIZER=m
+CONFIG_MACVLAN=m
+CONFIG_TUN=m
+CONFIG_VETH=m
+CONFIG_SGISEEQ=y
+CONFIG_SMC91X=m
+CONFIG_MDIO_BITBANG=m
+CONFIG_PHYLIB=m
+CONFIG_CICADA_PHY=m
+CONFIG_DAVICOM_PHY=m
+CONFIG_LXT_PHY=m
+CONFIG_MARVELL_PHY=m
+CONFIG_QSEMI_PHY=m
+CONFIG_REALTEK_PHY=m
+CONFIG_HOSTAP=m
+CONFIG_INPUT_MOUSEDEV=m
+CONFIG_MOUSE_PS2=m
+# CONFIG_MOUSE_PS2_ALPS is not set
+# CONFIG_MOUSE_PS2_SYNAPTICS is not set
+CONFIG_MOUSE_SERIAL=m
+CONFIG_SERIO_RAW=m
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_SERIAL_IP22_ZILOG=m
+# CONFIG_HW_RANDOM is not set
+# CONFIG_HWMON is not set
+CONFIG_THERMAL=y
+CONFIG_WATCHDOG=y
+CONFIG_INDYDOG=m
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_SGI_NEWPORT_CONSOLE=y
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+# CONFIG_LOGO_LINUX_VGA16 is not set
+# CONFIG_LOGO_LINUX_CLUT224 is not set
+CONFIG_HIDRAW=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_INTF_DEV_UIE_EMUL=y
+CONFIG_RTC_DRV_DS1286=y
+CONFIG_EXT2_FS=m
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_POSIX_ACL=y
+CONFIG_EXT3_FS_SECURITY=y
+CONFIG_XFS_FS=m
+CONFIG_XFS_QUOTA=y
+CONFIG_QUOTA=y
+CONFIG_QUOTA_NETLINK_INTERFACE=y
+# CONFIG_PRINT_QUOTA_WARNING is not set
+CONFIG_QFMT_V2=m
+CONFIG_AUTOFS4_FS=m
+CONFIG_FUSE_FS=m
+CONFIG_ISO9660_FS=m
+CONFIG_JOLIET=y
+CONFIG_ZISOFS=y
+CONFIG_UDF_FS=m
+CONFIG_MSDOS_FS=m
+CONFIG_VFAT_FS=m
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_EFS_FS=m
+CONFIG_MINIX_FS=m
+CONFIG_OMFS_FS=m
+CONFIG_UFS_FS=m
+CONFIG_NFS_FS=m
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFSD=m
+CONFIG_NFSD_V3_ACL=y
+CONFIG_CIFS=m
+CONFIG_CIFS_UPCALL=y
+CONFIG_CODA_FS=m
+CONFIG_NLS_CODEPAGE_437=m
+CONFIG_NLS_CODEPAGE_737=m
+CONFIG_NLS_CODEPAGE_775=m
+CONFIG_NLS_CODEPAGE_850=m
+CONFIG_NLS_CODEPAGE_852=m
+CONFIG_NLS_CODEPAGE_855=m
+CONFIG_NLS_CODEPAGE_857=m
+CONFIG_NLS_CODEPAGE_860=m
+CONFIG_NLS_CODEPAGE_861=m
+CONFIG_NLS_CODEPAGE_862=m
+CONFIG_NLS_CODEPAGE_863=m
+CONFIG_NLS_CODEPAGE_864=m
+CONFIG_NLS_CODEPAGE_865=m
+CONFIG_NLS_CODEPAGE_866=m
+CONFIG_NLS_CODEPAGE_869=m
+CONFIG_NLS_CODEPAGE_936=m
+CONFIG_NLS_CODEPAGE_950=m
+CONFIG_NLS_CODEPAGE_932=m
+CONFIG_NLS_CODEPAGE_949=m
+CONFIG_NLS_CODEPAGE_874=m
+CONFIG_NLS_ISO8859_8=m
+CONFIG_NLS_CODEPAGE_1250=m
+CONFIG_NLS_CODEPAGE_1251=m
+CONFIG_NLS_ASCII=m
+CONFIG_NLS_ISO8859_1=m
+CONFIG_NLS_ISO8859_2=m
+CONFIG_NLS_ISO8859_3=m
+CONFIG_NLS_ISO8859_4=m
+CONFIG_NLS_ISO8859_5=m
+CONFIG_NLS_ISO8859_6=m
+CONFIG_NLS_ISO8859_7=m
+CONFIG_NLS_ISO8859_9=m
+CONFIG_NLS_ISO8859_13=m
+CONFIG_NLS_ISO8859_14=m
+CONFIG_NLS_ISO8859_15=m
+CONFIG_NLS_KOI8_R=m
+CONFIG_NLS_KOI8_U=m
+CONFIG_NLS_UTF8=m
+CONFIG_KEYS=y
+CONFIG_CRYPTO_CRYPTD=m
+CONFIG_CRYPTO_GCM=m
+CONFIG_CRYPTO_CTS=m
+CONFIG_CRYPTO_LRW=m
+CONFIG_CRYPTO_PCBC=m
+CONFIG_CRYPTO_XTS=m
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_XCBC=m
+CONFIG_CRYPTO_RMD160=m
+CONFIG_CRYPTO_WP512=m
+CONFIG_CRYPTO_ANUBIS=m
+CONFIG_CRYPTO_BLOWFISH=m
+CONFIG_CRYPTO_CAMELLIA=m
+CONFIG_CRYPTO_CAST5=m
+CONFIG_CRYPTO_CAST6=m
+CONFIG_CRYPTO_FCRYPT=m
+CONFIG_CRYPTO_KHAZAD=m
+CONFIG_CRYPTO_SEED=m
+CONFIG_CRYPTO_SERPENT=m
+CONFIG_CRYPTO_TEA=m
+CONFIG_CRYPTO_TWOFISH=m
+CONFIG_CRYPTO_LZO=m
+# CONFIG_CRYPTO_HW is not set
+CONFIG_CRC_T10DIF=m
+CONFIG_DEBUG_MEMORY_INIT=y
diff --git a/arch/mips/configs/ip27_defconfig b/arch/mips/configs/ip27_defconfig
new file mode 100644
index 000000000..3e86f8106
--- /dev/null
+++ b/arch/mips/configs/ip27_defconfig
@@ -0,0 +1,325 @@
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=15
+CONFIG_CGROUPS=y
+CONFIG_CPUSETS=y
+CONFIG_RELAY=y
+CONFIG_EXPERT=y
+CONFIG_SLAB=y
+CONFIG_SGI_IP27=y
+CONFIG_NUMA=y
+CONFIG_SMP=y
+CONFIG_HZ_1000=y
+CONFIG_PCI=y
+CONFIG_MIPS32_O32=y
+CONFIG_MIPS32_N32=y
+CONFIG_PM=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=65536
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_XFRM_USER=m
+CONFIG_XFRM_STATISTICS=y
+CONFIG_NET_KEY=y
+CONFIG_NET_KEY_MIGRATE=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_TCP_MD5SIG=y
+CONFIG_IPV6_ROUTER_PREF=y
+CONFIG_IPV6_ROUTE_INFO=y
+CONFIG_IPV6_OPTIMISTIC_DAD=y
+CONFIG_INET6_AH=m
+CONFIG_INET6_ESP=m
+CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_MIP6=m
+CONFIG_IPV6_SIT=m
+CONFIG_IPV6_SIT_6RD=y
+CONFIG_IPV6_TUNNEL=m
+CONFIG_IPV6_MULTIPLE_TABLES=y
+CONFIG_IPV6_SUBTREES=y
+CONFIG_IPV6_MROUTE=y
+CONFIG_IPV6_PIMSM_V2=y
+CONFIG_NETWORK_SECMARK=y
+CONFIG_NET_SCHED=y
+CONFIG_NET_SCH_CBQ=m
+CONFIG_NET_SCH_HTB=m
+CONFIG_NET_SCH_HFSC=m
+CONFIG_NET_SCH_PRIO=m
+CONFIG_NET_SCH_MULTIQ=y
+CONFIG_NET_SCH_RED=m
+CONFIG_NET_SCH_SFQ=m
+CONFIG_NET_SCH_TEQL=m
+CONFIG_NET_SCH_TBF=m
+CONFIG_NET_SCH_GRED=m
+CONFIG_NET_SCH_DSMARK=m
+CONFIG_NET_SCH_NETEM=m
+CONFIG_NET_SCH_INGRESS=m
+CONFIG_NET_CLS_BASIC=m
+CONFIG_NET_CLS_TCINDEX=m
+CONFIG_NET_CLS_ROUTE4=m
+CONFIG_NET_CLS_FW=m
+CONFIG_NET_CLS_U32=m
+CONFIG_CLS_U32_MARK=y
+CONFIG_NET_CLS_RSVP=m
+CONFIG_NET_CLS_RSVP6=m
+CONFIG_NET_CLS_FLOW=m
+CONFIG_NET_CLS_CGROUP=y
+CONFIG_NET_CLS_ACT=y
+CONFIG_NET_ACT_POLICE=y
+CONFIG_NET_ACT_GACT=m
+CONFIG_GACT_PROB=y
+CONFIG_NET_ACT_MIRRED=m
+CONFIG_NET_ACT_NAT=m
+CONFIG_NET_ACT_PEDIT=m
+CONFIG_NET_ACT_SKBEDIT=m
+CONFIG_CFG80211=m
+CONFIG_MAC80211=m
+CONFIG_RFKILL=m
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_CDROM_PKTCDVD=m
+CONFIG_ATA_OVER_ETH=m
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_CHR_DEV_ST=y
+CONFIG_BLK_DEV_SR=m
+CONFIG_CHR_DEV_SG=m
+CONFIG_CHR_DEV_SCH=m
+CONFIG_SCSI_CONSTANTS=y
+CONFIG_SCSI_LOGGING=y
+CONFIG_SCSI_SCAN_ASYNC=y
+CONFIG_SCSI_SPI_ATTRS=y
+CONFIG_SCSI_FC_ATTRS=y
+CONFIG_SCSI_CXGB3_ISCSI=m
+CONFIG_SCSI_BNX2_ISCSI=m
+CONFIG_BE2ISCSI=m
+CONFIG_SCSI_HPSA=m
+CONFIG_SCSI_3W_SAS=m
+CONFIG_SCSI_AIC94XX=m
+# CONFIG_AIC94XX_DEBUG is not set
+CONFIG_SCSI_MVSAS=m
+# CONFIG_SCSI_MVSAS_DEBUG is not set
+CONFIG_SCSI_MPT2SAS=m
+CONFIG_LIBFC=m
+CONFIG_SCSI_QLOGIC_1280=y
+CONFIG_SCSI_PMCRAID=m
+CONFIG_SCSI_BFA_FC=m
+CONFIG_SCSI_DH=y
+CONFIG_SCSI_DH_RDAC=m
+CONFIG_SCSI_DH_HP_SW=m
+CONFIG_SCSI_DH_EMC=m
+CONFIG_SCSI_DH_ALUA=m
+CONFIG_MD=y
+CONFIG_BLK_DEV_MD=y
+CONFIG_MD_LINEAR=m
+CONFIG_MD_RAID0=y
+CONFIG_MD_RAID1=y
+CONFIG_MD_RAID10=m
+CONFIG_MD_RAID456=y
+CONFIG_MD_MULTIPATH=m
+CONFIG_MD_FAULTY=m
+CONFIG_BLK_DEV_DM=m
+CONFIG_DM_CRYPT=m
+CONFIG_DM_SNAPSHOT=m
+CONFIG_DM_MIRROR=m
+CONFIG_DM_LOG_USERSPACE=m
+CONFIG_DM_ZERO=m
+CONFIG_DM_MULTIPATH=m
+CONFIG_DM_MULTIPATH_QL=m
+CONFIG_DM_MULTIPATH_ST=m
+CONFIG_DM_UEVENT=y
+CONFIG_IFB=m
+CONFIG_MACVLAN=m
+CONFIG_VETH=m
+CONFIG_ATL2=m
+CONFIG_ATL1E=m
+CONFIG_ATL1C=m
+CONFIG_B44=m
+CONFIG_BNX2X=m
+CONFIG_ENIC=m
+CONFIG_DNET=m
+CONFIG_BE2NET=m
+CONFIG_E1000E=m
+CONFIG_IGB=m
+CONFIG_IGBVF=m
+CONFIG_IXGBE=m
+CONFIG_JME=m
+CONFIG_MLX4_EN=m
+# CONFIG_MLX4_DEBUG is not set
+CONFIG_KS8851_MLL=m
+CONFIG_AX88796=m
+CONFIG_AX88796_93CX6=y
+CONFIG_ETHOC=m
+CONFIG_QLA3XXX=m
+CONFIG_NETXEN_NIC=m
+CONFIG_SFC=m
+CONFIG_SGI_IOC3_ETH=y
+CONFIG_SMC91X=m
+CONFIG_SMSC911X=m
+CONFIG_NIU=m
+CONFIG_TEHUTI=m
+CONFIG_VIA_VELOCITY=m
+CONFIG_PHYLIB=y
+CONFIG_CICADA_PHY=m
+CONFIG_DAVICOM_PHY=m
+CONFIG_ICPLUS_PHY=m
+CONFIG_LSI_ET1011C_PHY=m
+CONFIG_LXT_PHY=m
+CONFIG_MARVELL_PHY=m
+CONFIG_NATIONAL_PHY=m
+CONFIG_QSEMI_PHY=m
+CONFIG_REALTEK_PHY=m
+CONFIG_SMSC_PHY=m
+CONFIG_STE10XP=m
+CONFIG_VITESSE_PHY=m
+CONFIG_ADM8211=m
+CONFIG_ATH5K=m
+CONFIG_ATH9K=m
+CONFIG_ATMEL=m
+CONFIG_PCI_ATMEL=m
+CONFIG_B43=m
+CONFIG_B43LEGACY=m
+# CONFIG_B43LEGACY_DEBUG is not set
+CONFIG_IPW2100=m
+CONFIG_IPW2100_MONITOR=y
+CONFIG_IPW2100_DEBUG=y
+CONFIG_IPW2200=m
+CONFIG_IPW2200_MONITOR=y
+CONFIG_IPW2200_PROMISCUOUS=y
+CONFIG_IPW2200_QOS=y
+CONFIG_IPW2200_DEBUG=y
+CONFIG_IWL4965=m
+CONFIG_IWL3945=m
+CONFIG_IWLWIFI=m
+CONFIG_HOSTAP=m
+CONFIG_HOSTAP_FIRMWARE=y
+CONFIG_HOSTAP_FIRMWARE_NVRAM=y
+CONFIG_HOSTAP_PLX=m
+CONFIG_HOSTAP_PCI=m
+CONFIG_HERMES=m
+# CONFIG_HERMES_CACHE_FW_ON_INIT is not set
+CONFIG_PLX_HERMES=m
+CONFIG_TMD_HERMES=m
+CONFIG_NORTEL_HERMES=m
+CONFIG_P54_COMMON=m
+CONFIG_P54_PCI=m
+CONFIG_LIBERTAS=m
+CONFIG_LIBERTAS_THINFIRM=m
+CONFIG_MWL8K=m
+CONFIG_RT2X00=m
+CONFIG_RT2400PCI=m
+CONFIG_RT2500PCI=m
+CONFIG_RT61PCI=m
+CONFIG_RT2800PCI=m
+CONFIG_RTL8180=m
+CONFIG_WL1251=m
+CONFIG_WL12XX=m
+# CONFIG_INPUT is not set
+CONFIG_SERIO_LIBPS2=m
+CONFIG_SERIO_RAW=m
+CONFIG_SERIO_ALTERA_PS2=m
+# CONFIG_VT is not set
+CONFIG_NOZOMI=m
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_EXTENDED=y
+CONFIG_SERIAL_8250_MANY_PORTS=y
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+CONFIG_HW_RANDOM_TIMERIOMEM=m
+CONFIG_I2C_CHARDEV=m
+CONFIG_I2C_ALI1535=m
+CONFIG_I2C_ALI1563=m
+CONFIG_I2C_ALI15X3=m
+CONFIG_I2C_AMD756=m
+CONFIG_I2C_AMD8111=m
+CONFIG_I2C_I801=m
+CONFIG_I2C_ISCH=m
+CONFIG_I2C_PIIX4=m
+CONFIG_I2C_NFORCE2=m
+CONFIG_I2C_SIS5595=m
+CONFIG_I2C_SIS630=m
+CONFIG_I2C_SIS96X=m
+CONFIG_I2C_VIA=m
+CONFIG_I2C_VIAPRO=m
+CONFIG_I2C_OCORES=m
+CONFIG_I2C_PCA_PLATFORM=m
+CONFIG_I2C_SIMTEC=m
+CONFIG_I2C_TAOS_EVM=m
+CONFIG_I2C_STUB=m
+# CONFIG_HWMON is not set
+CONFIG_THERMAL=y
+CONFIG_MFD_PCF50633=m
+CONFIG_PCF50633_ADC=m
+CONFIG_PCF50633_GPIO=m
+# CONFIG_VGA_ARB is not set
+CONFIG_LEDS_LP3944=m
+CONFIG_LEDS_PCA955X=m
+CONFIG_LEDS_BD2802=m
+CONFIG_LEDS_TRIGGER_TIMER=m
+CONFIG_LEDS_TRIGGER_HEARTBEAT=m
+CONFIG_LEDS_TRIGGER_BACKLIGHT=m
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=m
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_M48T35=y
+CONFIG_UIO=y
+CONFIG_UIO_AEC=m
+CONFIG_UIO_SERCOS3=m
+CONFIG_UIO_PCI_GENERIC=m
+CONFIG_EXT2_FS=y
+CONFIG_EXT2_FS_XATTR=y
+CONFIG_EXT2_FS_POSIX_ACL=y
+CONFIG_EXT2_FS_SECURITY=y
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_POSIX_ACL=y
+CONFIG_EXT3_FS_SECURITY=y
+CONFIG_XFS_FS=m
+CONFIG_XFS_QUOTA=y
+CONFIG_XFS_POSIX_ACL=y
+CONFIG_BTRFS_FS=m
+CONFIG_BTRFS_FS_POSIX_ACL=y
+CONFIG_QUOTA_NETLINK_INTERFACE=y
+CONFIG_FUSE_FS=m
+CONFIG_CUSE=m
+CONFIG_FSCACHE=m
+CONFIG_FSCACHE_STATS=y
+CONFIG_CACHEFILES=m
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_SQUASHFS=m
+CONFIG_OMFS_FS=m
+CONFIG_NFS_FS=y
+CONFIG_SECURITYFS=y
+CONFIG_CRYPTO_CRYPTD=m
+CONFIG_CRYPTO_CTS=m
+CONFIG_CRYPTO_LRW=m
+CONFIG_CRYPTO_PCBC=m
+CONFIG_CRYPTO_XTS=m
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_XCBC=m
+CONFIG_CRYPTO_VMAC=m
+CONFIG_CRYPTO_MD4=m
+CONFIG_CRYPTO_RMD160=m
+CONFIG_CRYPTO_SHA512=m
+CONFIG_CRYPTO_WP512=m
+CONFIG_CRYPTO_ANUBIS=m
+CONFIG_CRYPTO_BLOWFISH=m
+CONFIG_CRYPTO_CAMELLIA=m
+CONFIG_CRYPTO_CAST5=m
+CONFIG_CRYPTO_CAST6=m
+CONFIG_CRYPTO_FCRYPT=m
+CONFIG_CRYPTO_KHAZAD=m
+CONFIG_CRYPTO_SEED=m
+CONFIG_CRYPTO_SERPENT=m
+CONFIG_CRYPTO_TEA=m
+CONFIG_CRYPTO_TWOFISH=m
+CONFIG_CRYPTO_LZO=m
+CONFIG_CRC_T10DIF=m
diff --git a/arch/mips/configs/ip28_defconfig b/arch/mips/configs/ip28_defconfig
new file mode 100644
index 000000000..ba13eea05
--- /dev/null
+++ b/arch/mips/configs/ip28_defconfig
@@ -0,0 +1,66 @@
+CONFIG_SYSVIPC=y
+CONFIG_PREEMPT_VOLUNTARY=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_RELAY=y
+CONFIG_EXPERT=y
+CONFIG_SLAB=y
+CONFIG_SGI_IP28=y
+CONFIG_ARC_CONSOLE=y
+CONFIG_EISA=y
+CONFIG_MIPS32_O32=y
+CONFIG_MIPS32_N32=y
+# CONFIG_SUSPEND is not set
+CONFIG_PM=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_NET_KEY=y
+CONFIG_NET_KEY_MIGRATE=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_TCP_MD5SIG=y
+# CONFIG_IPV6 is not set
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_BLK_DEV_SR=y
+CONFIG_SCSI_CONSTANTS=y
+CONFIG_SGIWD93_SCSI=y
+CONFIG_NETDEVICES=y
+CONFIG_DUMMY=m
+CONFIG_SGISEEQ=y
+# CONFIG_MOUSE_PS2_ALPS is not set
+# CONFIG_MOUSE_PS2_SYNAPTICS is not set
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_SERIAL_IP22_ZILOG=y
+CONFIG_SERIAL_IP22_ZILOG_CONSOLE=y
+# CONFIG_HW_RANDOM is not set
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_INDYDOG=y
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_EXT2_FS=y
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_POSIX_ACL=y
+CONFIG_EXT3_FS_SECURITY=y
+CONFIG_QUOTA=y
+CONFIG_PROC_KCORE=y
+# CONFIG_PROC_PAGE_MONITOR is not set
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3_ACL=y
+CONFIG_ROOT_NFS=y
+CONFIG_CRYPTO_MANAGER=y
+# CONFIG_CRYPTO_HW is not set
+CONFIG_MAGIC_SYSRQ=y
diff --git a/arch/mips/configs/ip32_defconfig b/arch/mips/configs/ip32_defconfig
new file mode 100644
index 000000000..8ced2224c
--- /dev/null
+++ b/arch/mips/configs/ip32_defconfig
@@ -0,0 +1,186 @@
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_AUDIT=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_RELAY=y
+CONFIG_EXPERT=y
+CONFIG_SLAB=y
+CONFIG_PROFILING=y
+CONFIG_SGI_IP32=y
+# CONFIG_SECCOMP is not set
+CONFIG_PCI=y
+CONFIG_MIPS32_O32=y
+CONFIG_MIPS32_N32=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_SGI_PARTITION=y
+CONFIG_BINFMT_MISC=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_XFRM_USER=y
+CONFIG_NET_KEY=y
+CONFIG_NET_KEY_MIGRATE=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_NET_IPIP=m
+CONFIG_INET_AH=m
+CONFIG_INET_ESP=m
+CONFIG_INET_IPCOMP=m
+CONFIG_TCP_CONG_ADVANCED=y
+CONFIG_TCP_MD5SIG=y
+CONFIG_INET6_AH=m
+CONFIG_INET6_ESP=m
+CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_TUNNEL=m
+CONFIG_NETWORK_SECMARK=y
+CONFIG_CONNECTOR=y
+CONFIG_BLK_DEV_LOOP=m
+CONFIG_BLK_DEV_NBD=m
+CONFIG_RAID_ATTRS=y
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_BLK_DEV_SR=y
+CONFIG_CHR_DEV_SG=m
+CONFIG_SCSI_CONSTANTS=y
+CONFIG_SCSI_LOGGING=y
+CONFIG_SCSI_SCAN_ASYNC=y
+CONFIG_SCSI_SAS_LIBSAS=y
+CONFIG_SCSI_AIC7XXX=y
+CONFIG_AIC7XXX_RESET_DELAY_MS=15000
+CONFIG_NETDEVICES=y
+CONFIG_BONDING=m
+CONFIG_DUMMY=m
+CONFIG_NET_TULIP=y
+CONFIG_DE2104X=m
+CONFIG_TULIP=m
+CONFIG_TULIP_MMIO=y
+CONFIG_SGI_O2MACE_ETH=y
+CONFIG_INPUT_EVDEV=m
+CONFIG_SERIO_MACEPS2=y
+CONFIG_SERIO_RAW=y
+# CONFIG_CONSOLE_TRANSLATIONS is not set
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_HW_RANDOM=y
+CONFIG_WATCHDOG=y
+CONFIG_FB=y
+CONFIG_FIRMWARE_EDID=y
+CONFIG_FB_GBE=y
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+# CONFIG_LOGO_LINUX_VGA16 is not set
+# CONFIG_LOGO_LINUX_CLUT224 is not set
+# CONFIG_USB_SUPPORT is not set
+CONFIG_RTC_CLASS=y
+# CONFIG_RTC_HCTOSYS is not set
+# CONFIG_RTC_INTF_SYSFS is not set
+# CONFIG_RTC_INTF_PROC is not set
+CONFIG_RTC_DRV_DS1685_FAMILY=y
+CONFIG_EXT2_FS=y
+CONFIG_EXT2_FS_XATTR=y
+CONFIG_EXT2_FS_POSIX_ACL=y
+CONFIG_EXT2_FS_SECURITY=y
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_POSIX_ACL=y
+CONFIG_EXT3_FS_SECURITY=y
+CONFIG_QUOTA=y
+CONFIG_QFMT_V1=m
+CONFIG_QFMT_V2=m
+CONFIG_AUTOFS4_FS=m
+CONFIG_FUSE_FS=m
+CONFIG_ISO9660_FS=m
+CONFIG_JOLIET=y
+CONFIG_ZISOFS=y
+CONFIG_UDF_FS=m
+CONFIG_MSDOS_FS=m
+CONFIG_VFAT_FS=m
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_NFS_FS=y
+CONFIG_ROOT_NFS=y
+CONFIG_NFSD=m
+CONFIG_CIFS=m
+CONFIG_NLS=y
+CONFIG_NLS_CODEPAGE_437=m
+CONFIG_NLS_CODEPAGE_737=m
+CONFIG_NLS_CODEPAGE_775=m
+CONFIG_NLS_CODEPAGE_850=m
+CONFIG_NLS_CODEPAGE_852=m
+CONFIG_NLS_CODEPAGE_855=m
+CONFIG_NLS_CODEPAGE_857=m
+CONFIG_NLS_CODEPAGE_860=m
+CONFIG_NLS_CODEPAGE_861=m
+CONFIG_NLS_CODEPAGE_862=m
+CONFIG_NLS_CODEPAGE_863=m
+CONFIG_NLS_CODEPAGE_864=m
+CONFIG_NLS_CODEPAGE_865=m
+CONFIG_NLS_CODEPAGE_866=m
+CONFIG_NLS_CODEPAGE_869=m
+CONFIG_NLS_CODEPAGE_936=m
+CONFIG_NLS_CODEPAGE_950=m
+CONFIG_NLS_CODEPAGE_932=m
+CONFIG_NLS_CODEPAGE_949=m
+CONFIG_NLS_CODEPAGE_874=m
+CONFIG_NLS_ISO8859_8=m
+CONFIG_NLS_CODEPAGE_1250=m
+CONFIG_NLS_CODEPAGE_1251=m
+CONFIG_NLS_ASCII=m
+CONFIG_NLS_ISO8859_1=m
+CONFIG_NLS_ISO8859_2=m
+CONFIG_NLS_ISO8859_3=m
+CONFIG_NLS_ISO8859_4=m
+CONFIG_NLS_ISO8859_5=m
+CONFIG_NLS_ISO8859_6=m
+CONFIG_NLS_ISO8859_7=m
+CONFIG_NLS_ISO8859_9=m
+CONFIG_NLS_ISO8859_13=m
+CONFIG_NLS_ISO8859_14=m
+CONFIG_NLS_ISO8859_15=m
+CONFIG_NLS_KOI8_R=m
+CONFIG_NLS_KOI8_U=m
+CONFIG_NLS_UTF8=m
+CONFIG_KEYS=y
+CONFIG_CRYPTO_NULL=y
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_ECB=y
+CONFIG_CRYPTO_LRW=y
+CONFIG_CRYPTO_PCBC=y
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_XCBC=y
+CONFIG_CRYPTO_MD4=y
+CONFIG_CRYPTO_MICHAEL_MIC=y
+CONFIG_CRYPTO_SHA1=y
+CONFIG_CRYPTO_SHA256=y
+CONFIG_CRYPTO_SHA512=y
+CONFIG_CRYPTO_WP512=y
+CONFIG_CRYPTO_ANUBIS=y
+CONFIG_CRYPTO_ARC4=y
+CONFIG_CRYPTO_BLOWFISH=y
+CONFIG_CRYPTO_CAMELLIA=y
+CONFIG_CRYPTO_CAST5=y
+CONFIG_CRYPTO_CAST6=y
+CONFIG_CRYPTO_DES=y
+CONFIG_CRYPTO_FCRYPT=y
+CONFIG_CRYPTO_KHAZAD=y
+CONFIG_CRYPTO_SERPENT=y
+CONFIG_CRYPTO_TEA=y
+CONFIG_CRYPTO_TWOFISH=y
+CONFIG_CRYPTO_DEFLATE=y
+CONFIG_CRC_T10DIF=y
+CONFIG_LIBCRC32C=y
+CONFIG_FONTS=y
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y
+CONFIG_MAGIC_SYSRQ=y
diff --git a/arch/mips/configs/jazz_defconfig b/arch/mips/configs/jazz_defconfig
new file mode 100644
index 000000000..106b21cb6
--- /dev/null
+++ b/arch/mips/configs/jazz_defconfig
@@ -0,0 +1,94 @@
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT_VOLUNTARY=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_RELAY=y
+CONFIG_EXPERT=y
+CONFIG_SLAB=y
+CONFIG_MACH_JAZZ=y
+CONFIG_OLIVETTI_M700=y
+CONFIG_MIPS_MAGNUM_4000=y
+CONFIG_CPU_LITTLE_ENDIAN=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_BINFMT_MISC=m
+CONFIG_NET=y
+CONFIG_PACKET=m
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_NET_IPIP=m
+CONFIG_INET6_AH=m
+CONFIG_INET6_ESP=m
+CONFIG_INET6_IPCOMP=m
+CONFIG_PARPORT=m
+CONFIG_PARPORT_PC=m
+CONFIG_PARPORT_1284=y
+CONFIG_DEVTMPFS=y
+CONFIG_BLK_DEV_FD=m
+CONFIG_BLK_DEV_LOOP=m
+CONFIG_BLK_DEV_NBD=m
+CONFIG_BLK_DEV_RAM=m
+CONFIG_CDROM_PKTCDVD=m
+CONFIG_ATA_OVER_ETH=m
+CONFIG_RAID_ATTRS=m
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_CHR_DEV_ST=m
+CONFIG_BLK_DEV_SR=m
+CONFIG_SCSI_CONSTANTS=y
+CONFIG_SCSI_SCAN_ASYNC=y
+CONFIG_ISCSI_TCP=m
+CONFIG_SCSI_PPA=m
+CONFIG_SCSI_IMM=m
+CONFIG_JAZZ_ESP=y
+CONFIG_ATA=y
+CONFIG_PATA_LEGACY=y
+CONFIG_NETDEVICES=y
+CONFIG_BONDING=m
+CONFIG_DUMMY=m
+CONFIG_EQUALIZER=m
+CONFIG_TUN=m
+CONFIG_MIPS_JAZZ_SONIC=y
+CONFIG_NE2000=m
+CONFIG_SERIO_PARKBD=m
+CONFIG_SERIO_RAW=m
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_EXTENDED=y
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+CONFIG_SERIAL_8250_DETECT_IRQ=y
+CONFIG_SERIAL_8250_RSA=y
+CONFIG_FB=y
+CONFIG_FB_G364=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+# CONFIG_HWMON is not set
+CONFIG_EXT2_FS=m
+CONFIG_EXT3_FS=y
+CONFIG_REISERFS_FS=m
+CONFIG_REISERFS_FS_XATTR=y
+CONFIG_REISERFS_FS_POSIX_ACL=y
+CONFIG_REISERFS_FS_SECURITY=y
+CONFIG_XFS_FS=m
+CONFIG_XFS_QUOTA=y
+CONFIG_AUTOFS4_FS=m
+CONFIG_FUSE_FS=m
+CONFIG_ISO9660_FS=m
+CONFIG_JOLIET=y
+CONFIG_ZISOFS=y
+CONFIG_UDF_FS=m
+CONFIG_MSDOS_FS=m
+CONFIG_VFAT_FS=m
+CONFIG_NTFS_FS=m
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_UFS_FS=m
+CONFIG_NFS_FS=m
+CONFIG_NFSD=m
+CONFIG_CIFS=m
diff --git a/arch/mips/configs/lemote2f_defconfig b/arch/mips/configs/lemote2f_defconfig
new file mode 100644
index 000000000..7e598d338
--- /dev/null
+++ b/arch/mips/configs/lemote2f_defconfig
@@ -0,0 +1,339 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SYSVIPC=y
+CONFIG_AUDIT=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=15
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_EXPERT=y
+CONFIG_PROFILING=y
+CONFIG_MACH_LOONGSON2EF=y
+CONFIG_LEMOTE_MACH2F=y
+CONFIG_KEXEC=y
+# CONFIG_SECCOMP is not set
+CONFIG_PCI=y
+CONFIG_MIPS32_O32=y
+CONFIG_MIPS32_N32=y
+CONFIG_HIBERNATION=y
+CONFIG_PM_STD_PARTITION="/dev/hda3"
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_BLK_DEV_INTEGRITY=y
+CONFIG_MQ_IOSCHED_DEADLINE=m
+CONFIG_BINFMT_MISC=m
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_XFRM_USER=m
+CONFIG_NET_KEY=m
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_MULTIPLE_TABLES=y
+CONFIG_IP_ROUTE_MULTIPATH=y
+CONFIG_IP_ROUTE_VERBOSE=y
+CONFIG_NET_IPIP=m
+CONFIG_IP_MROUTE=y
+CONFIG_IP_PIMSM_V1=y
+CONFIG_IP_PIMSM_V2=y
+CONFIG_SYN_COOKIES=y
+CONFIG_TCP_CONG_ADVANCED=y
+CONFIG_TCP_CONG_BIC=y
+CONFIG_DEFAULT_BIC=y
+CONFIG_TCP_MD5SIG=y
+CONFIG_IPV6_ROUTER_PREF=y
+CONFIG_IPV6_TUNNEL=m
+CONFIG_IPV6_MULTIPLE_TABLES=y
+CONFIG_IPV6_SUBTREES=y
+CONFIG_NETWORK_SECMARK=y
+CONFIG_NETFILTER=y
+CONFIG_BRIDGE=m
+CONFIG_VLAN_8021Q=m
+CONFIG_NET_SCHED=y
+CONFIG_NET_EMATCH=y
+CONFIG_NET_CLS_ACT=y
+CONFIG_BT=m
+CONFIG_BT_RFCOMM=m
+CONFIG_BT_RFCOMM_TTY=y
+CONFIG_BT_BNEP=m
+CONFIG_BT_BNEP_MC_FILTER=y
+CONFIG_BT_BNEP_PROTO_FILTER=y
+CONFIG_BT_HIDP=m
+CONFIG_BT_HCIBTUSB=m
+CONFIG_BT_HCIBFUSB=m
+CONFIG_BT_HCIVHCI=m
+CONFIG_CFG80211=m
+CONFIG_MAC80211=m
+CONFIG_MAC80211_LEDS=y
+CONFIG_RFKILL=m
+CONFIG_RFKILL_INPUT=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_SIZE=8192
+CONFIG_BLK_DEV_SD=y
+CONFIG_CHR_DEV_SG=m
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_ATA=y
+CONFIG_PATA_AMD=y
+CONFIG_MD=y
+CONFIG_BLK_DEV_MD=m
+CONFIG_MD_LINEAR=m
+CONFIG_MD_RAID0=m
+CONFIG_MD_RAID1=m
+CONFIG_MD_RAID10=m
+CONFIG_MD_RAID456=m
+CONFIG_MD_MULTIPATH=m
+CONFIG_MD_FAULTY=m
+CONFIG_BLK_DEV_DM=m
+CONFIG_DM_DEBUG=y
+CONFIG_DM_CRYPT=m
+CONFIG_DM_SNAPSHOT=m
+CONFIG_DM_MIRROR=m
+CONFIG_DM_LOG_USERSPACE=m
+CONFIG_DM_ZERO=m
+CONFIG_DM_MULTIPATH=m
+CONFIG_DM_MULTIPATH_QL=m
+CONFIG_DM_MULTIPATH_ST=m
+CONFIG_DM_DELAY=m
+CONFIG_DM_UEVENT=y
+CONFIG_NETDEVICES=y
+CONFIG_DUMMY=m
+CONFIG_NETCONSOLE=m
+CONFIG_TUN=m
+CONFIG_VETH=m
+CONFIG_8139TOO=y
+# CONFIG_8139TOO_PIO is not set
+CONFIG_R8169=y
+CONFIG_USB_USBNET=m
+CONFIG_USB_NET_CDC_EEM=m
+CONFIG_INPUT_EVDEV=y
+# CONFIG_MOUSE_PS2_ALPS is not set
+# CONFIG_MOUSE_PS2_LOGIPS2PP is not set
+# CONFIG_MOUSE_PS2_TRACKPOINT is not set
+CONFIG_MOUSE_APPLETOUCH=m
+# CONFIG_SERIO_SERPORT is not set
+CONFIG_LEGACY_PTY_COUNT=16
+CONFIG_SERIAL_NONSTANDARD=y
+CONFIG_SERIAL_8250=m
+# CONFIG_SERIAL_8250_PCI is not set
+CONFIG_SERIAL_8250_NR_UARTS=16
+CONFIG_SERIAL_8250_EXTENDED=y
+CONFIG_SERIAL_8250_MANY_PORTS=y
+CONFIG_SERIAL_8250_FOURPORT=y
+CONFIG_HW_RANDOM=y
+CONFIG_GPIO_LOONGSON=y
+CONFIG_THERMAL=y
+CONFIG_MEDIA_SUPPORT=m
+CONFIG_FB=y
+CONFIG_FIRMWARE_EDID=y
+CONFIG_FB_MODE_HELPERS=y
+CONFIG_FB_TILEBLITTING=y
+CONFIG_FB_SIS=y
+CONFIG_FB_SIS_300=y
+CONFIG_FB_SIS_315=y
+# CONFIG_LCD_CLASS_DEVICE is not set
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+# CONFIG_LOGO_LINUX_VGA16 is not set
+CONFIG_SOUND=m
+CONFIG_SND=m
+CONFIG_SND_HRTIMER=m
+CONFIG_SND_SEQUENCER=m
+CONFIG_SND_SEQ_DUMMY=m
+CONFIG_SND_DUMMY=m
+CONFIG_SND_VIRMIDI=m
+CONFIG_SND_SERIAL_U16550=m
+CONFIG_SND_MPU401=m
+CONFIG_SND_AC97_POWER_SAVE=y
+CONFIG_SND_AC97_POWER_SAVE_DEFAULT=10
+CONFIG_SND_CS5535AUDIO=m
+# CONFIG_SND_MIPS is not set
+CONFIG_SND_USB_AUDIO=m
+CONFIG_SND_USB_CAIAQ=m
+CONFIG_SND_USB_CAIAQ_INPUT=y
+CONFIG_HIDRAW=y
+CONFIG_HID_A4TECH=m
+CONFIG_HID_APPLE=m
+CONFIG_HID_BELKIN=m
+CONFIG_HID_CHERRY=m
+CONFIG_HID_CHICONY=m
+CONFIG_HID_CYPRESS=m
+CONFIG_HID_DRAGONRISE=m
+CONFIG_DRAGONRISE_FF=y
+CONFIG_HID_EZKEY=m
+CONFIG_HID_KYE=m
+CONFIG_HID_GYRATION=m
+CONFIG_HID_TWINHAN=m
+CONFIG_HID_KENSINGTON=m
+CONFIG_HID_LOGITECH=m
+CONFIG_LOGITECH_FF=y
+CONFIG_LOGIRUMBLEPAD2_FF=y
+CONFIG_HID_MICROSOFT=m
+CONFIG_HID_MONTEREY=m
+CONFIG_HID_NTRIG=m
+CONFIG_HID_PANTHERLORD=m
+CONFIG_PANTHERLORD_FF=y
+CONFIG_HID_PETALYNX=m
+CONFIG_HID_SAMSUNG=m
+CONFIG_HID_SONY=m
+CONFIG_HID_SUNPLUS=m
+CONFIG_HID_GREENASIA=m
+CONFIG_GREENASIA_FF=y
+CONFIG_HID_SMARTJOYPLUS=m
+CONFIG_SMARTJOYPLUS_FF=y
+CONFIG_HID_TOPSEED=m
+CONFIG_HID_THRUSTMASTER=m
+CONFIG_THRUSTMASTER_FF=y
+CONFIG_HID_WACOM=m
+CONFIG_HID_ZEROPLUS=m
+CONFIG_ZEROPLUS_FF=y
+CONFIG_USB_HIDDEV=y
+CONFIG_USB=y
+CONFIG_USB_DYNAMIC_MINORS=y
+CONFIG_USB_OTG_PRODUCTLIST=y
+CONFIG_USB_MON=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_ROOT_HUB_TT=y
+# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_UHCI_HCD=m
+CONFIG_USB_ACM=m
+CONFIG_USB_PRINTER=m
+CONFIG_USB_WDM=m
+CONFIG_USB_STORAGE=m
+CONFIG_USB_STORAGE_DATAFAB=m
+CONFIG_USB_STORAGE_FREECOM=m
+CONFIG_USB_STORAGE_ISD200=m
+CONFIG_USB_STORAGE_USBAT=m
+CONFIG_USB_STORAGE_SDDR09=m
+CONFIG_USB_STORAGE_SDDR55=m
+CONFIG_USB_STORAGE_JUMPSHOT=m
+CONFIG_USB_STORAGE_ALAUDA=m
+CONFIG_USB_SERIAL=m
+CONFIG_USB_SERIAL_GENERIC=y
+CONFIG_USB_GADGET=m
+CONFIG_MMC=m
+CONFIG_LEDS_CLASS=y
+CONFIG_STAGING=y
+CONFIG_EXT2_FS=m
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_POSIX_ACL=y
+CONFIG_EXT3_FS_SECURITY=y
+CONFIG_REISERFS_FS=m
+CONFIG_REISERFS_PROC_INFO=y
+CONFIG_REISERFS_FS_XATTR=y
+CONFIG_JFS_FS=m
+CONFIG_JFS_POSIX_ACL=y
+CONFIG_XFS_FS=m
+CONFIG_XFS_QUOTA=y
+CONFIG_XFS_POSIX_ACL=y
+CONFIG_BTRFS_FS=m
+CONFIG_QUOTA=y
+CONFIG_QFMT_V2=m
+CONFIG_AUTOFS4_FS=m
+CONFIG_FSCACHE=m
+CONFIG_CACHEFILES=m
+CONFIG_ISO9660_FS=m
+CONFIG_JOLIET=y
+CONFIG_ZISOFS=y
+CONFIG_MSDOS_FS=m
+CONFIG_VFAT_FS=m
+CONFIG_NTFS_FS=m
+CONFIG_NTFS_RW=y
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_CRAMFS=m
+CONFIG_SQUASHFS=m
+CONFIG_SQUASHFS_EMBEDDED=y
+CONFIG_ROMFS_FS=m
+CONFIG_NFS_FS=m
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFSD=m
+CONFIG_NFSD_V4=y
+CONFIG_CIFS=m
+CONFIG_NLS_DEFAULT="utf8"
+CONFIG_NLS_CODEPAGE_437=m
+CONFIG_NLS_CODEPAGE_737=m
+CONFIG_NLS_CODEPAGE_775=m
+CONFIG_NLS_CODEPAGE_850=m
+CONFIG_NLS_CODEPAGE_852=m
+CONFIG_NLS_CODEPAGE_855=m
+CONFIG_NLS_CODEPAGE_857=m
+CONFIG_NLS_CODEPAGE_860=m
+CONFIG_NLS_CODEPAGE_861=m
+CONFIG_NLS_CODEPAGE_862=m
+CONFIG_NLS_CODEPAGE_863=m
+CONFIG_NLS_CODEPAGE_864=m
+CONFIG_NLS_CODEPAGE_865=m
+CONFIG_NLS_CODEPAGE_866=m
+CONFIG_NLS_CODEPAGE_869=m
+CONFIG_NLS_CODEPAGE_936=m
+CONFIG_NLS_CODEPAGE_950=m
+CONFIG_NLS_CODEPAGE_932=m
+CONFIG_NLS_CODEPAGE_949=m
+CONFIG_NLS_CODEPAGE_874=m
+CONFIG_NLS_ISO8859_8=m
+CONFIG_NLS_CODEPAGE_1250=m
+CONFIG_NLS_CODEPAGE_1251=m
+CONFIG_NLS_ASCII=m
+CONFIG_NLS_ISO8859_1=m
+CONFIG_NLS_ISO8859_2=m
+CONFIG_NLS_ISO8859_3=m
+CONFIG_NLS_ISO8859_4=m
+CONFIG_NLS_ISO8859_5=m
+CONFIG_NLS_ISO8859_6=m
+CONFIG_NLS_ISO8859_7=m
+CONFIG_NLS_ISO8859_9=m
+CONFIG_NLS_ISO8859_13=m
+CONFIG_NLS_ISO8859_14=m
+CONFIG_NLS_ISO8859_15=m
+CONFIG_NLS_KOI8_R=m
+CONFIG_NLS_KOI8_U=m
+CONFIG_NLS_UTF8=y
+CONFIG_CRYPTO_CRYPTD=m
+CONFIG_CRYPTO_AUTHENC=m
+CONFIG_CRYPTO_TEST=m
+CONFIG_CRYPTO_LRW=m
+CONFIG_CRYPTO_PCBC=m
+CONFIG_CRYPTO_XTS=m
+CONFIG_CRYPTO_XCBC=m
+CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_RMD160=m
+CONFIG_CRYPTO_SHA1=m
+CONFIG_CRYPTO_WP512=m
+CONFIG_CRYPTO_ANUBIS=m
+CONFIG_CRYPTO_BLOWFISH=m
+CONFIG_CRYPTO_CAMELLIA=m
+CONFIG_CRYPTO_CAST5=m
+CONFIG_CRYPTO_CAST6=m
+CONFIG_CRYPTO_FCRYPT=m
+CONFIG_CRYPTO_KHAZAD=m
+CONFIG_CRYPTO_SEED=m
+CONFIG_CRYPTO_SERPENT=m
+CONFIG_CRYPTO_TEA=m
+CONFIG_CRYPTO_TWOFISH=m
+CONFIG_CRYPTO_DEFLATE=m
+CONFIG_CRYPTO_LZO=m
+CONFIG_FONTS=y
+CONFIG_FONT_8x8=y
+CONFIG_FONT_6x11=y
+CONFIG_FONT_7x14=y
+CONFIG_FONT_PEARL_8x8=y
+CONFIG_FONT_ACORN_8x8=y
+CONFIG_FONT_MINI_4x6=y
+CONFIG_FONT_10x18=y
+CONFIG_FONT_SUN8x16=y
+CONFIG_FONT_SUN12x22=y
+CONFIG_PRINTK_TIME=y
+CONFIG_FRAME_WARN=1024
+CONFIG_STRIP_ASM_SYMS=y
diff --git a/arch/mips/configs/loongson1b_defconfig b/arch/mips/configs/loongson1b_defconfig
new file mode 100644
index 000000000..68207b31d
--- /dev/null
+++ b/arch/mips/configs/loongson1b_defconfig
@@ -0,0 +1,120 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_KERNEL_XZ=y
+CONFIG_SYSVIPC=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=16
+CONFIG_NAMESPACES=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_EXPERT=y
+CONFIG_PERF_EVENTS=y
+# CONFIG_COMPAT_BRK is not set
+CONFIG_MACH_LOONGSON32=y
+# CONFIG_SECCOMP is not set
+# CONFIG_SUSPEND is not set
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_DIAG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_WIRELESS is not set
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+# CONFIG_STANDALONE is not set
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_RAW_NAND=y
+CONFIG_MTD_UBI=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_SCSI=m
+# CONFIG_SCSI_PROC_FS is not set
+CONFIG_BLK_DEV_SD=m
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+CONFIG_STMMAC_ETH=y
+# CONFIG_NET_VENDOR_WIZNET is not set
+# CONFIG_WLAN is not set
+CONFIG_INPUT_EVDEV=y
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_LEGACY_PTY_COUNT=8
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+# CONFIG_HW_RANDOM is not set
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_LOONGSON1=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_WATCHDOG_NOWAYOUT=y
+CONFIG_WATCHDOG_SYSFS=y
+CONFIG_LOONGSON1_WDT=y
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_HID_GENERIC=m
+CONFIG_USB_HID=m
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_EHCI_HCD=y
+# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+CONFIG_USB_EHCI_HCD_PLATFORM=y
+CONFIG_USB_STORAGE=m
+CONFIG_USB_SERIAL=m
+CONFIG_USB_SERIAL_PL2303=m
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_LOONGSON1=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_EXT2_FS=y
+CONFIG_EXT2_FS_XATTR=y
+CONFIG_EXT2_FS_POSIX_ACL=y
+CONFIG_EXT2_FS_SECURITY=y
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_POSIX_ACL=y
+CONFIG_EXT3_FS_SECURITY=y
+# CONFIG_DNOTIFY is not set
+CONFIG_VFAT_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_UBIFS_FS=y
+CONFIG_UBIFS_FS_ADVANCED_COMPR=y
+CONFIG_UBIFS_ATIME_SUPPORT=y
+CONFIG_NFS_FS=y
+CONFIG_ROOT_NFS=y
+CONFIG_NLS_CODEPAGE_437=m
+CONFIG_NLS_ISO8859_1=m
+# CONFIG_CRYPTO_ECHAINIV is not set
+# CONFIG_CRYPTO_HW is not set
+CONFIG_DYNAMIC_DEBUG=y
+CONFIG_DEBUG_FS=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_PREEMPT is not set
+# CONFIG_FTRACE is not set
+# CONFIG_EARLY_PRINTK is not set
diff --git a/arch/mips/configs/loongson1c_defconfig b/arch/mips/configs/loongson1c_defconfig
new file mode 100644
index 000000000..c3910a9de
--- /dev/null
+++ b/arch/mips/configs/loongson1c_defconfig
@@ -0,0 +1,121 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_KERNEL_XZ=y
+CONFIG_SYSVIPC=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=16
+CONFIG_NAMESPACES=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_EXPERT=y
+CONFIG_PERF_EVENTS=y
+# CONFIG_COMPAT_BRK is not set
+CONFIG_MACH_LOONGSON32=y
+CONFIG_LOONGSON1_LS1C=y
+# CONFIG_SECCOMP is not set
+# CONFIG_SUSPEND is not set
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_DIAG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_WIRELESS is not set
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+# CONFIG_STANDALONE is not set
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_RAW_NAND=y
+CONFIG_MTD_UBI=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_SCSI=m
+# CONFIG_SCSI_PROC_FS is not set
+CONFIG_BLK_DEV_SD=m
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+CONFIG_STMMAC_ETH=y
+# CONFIG_NET_VENDOR_WIZNET is not set
+# CONFIG_WLAN is not set
+CONFIG_INPUT_EVDEV=y
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_LEGACY_PTY_COUNT=8
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+# CONFIG_HW_RANDOM is not set
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_LOONGSON1=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_WATCHDOG_NOWAYOUT=y
+CONFIG_WATCHDOG_SYSFS=y
+CONFIG_LOONGSON1_WDT=y
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_HID_GENERIC=m
+CONFIG_USB_HID=m
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_EHCI_HCD=y
+# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+CONFIG_USB_EHCI_HCD_PLATFORM=y
+CONFIG_USB_STORAGE=m
+CONFIG_USB_SERIAL=m
+CONFIG_USB_SERIAL_PL2303=m
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_LOONGSON1=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_EXT2_FS=y
+CONFIG_EXT2_FS_XATTR=y
+CONFIG_EXT2_FS_POSIX_ACL=y
+CONFIG_EXT2_FS_SECURITY=y
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_POSIX_ACL=y
+CONFIG_EXT3_FS_SECURITY=y
+# CONFIG_DNOTIFY is not set
+CONFIG_VFAT_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_UBIFS_FS=y
+CONFIG_UBIFS_FS_ADVANCED_COMPR=y
+CONFIG_UBIFS_ATIME_SUPPORT=y
+CONFIG_NFS_FS=y
+CONFIG_ROOT_NFS=y
+CONFIG_NLS_CODEPAGE_437=m
+CONFIG_NLS_ISO8859_1=m
+# CONFIG_CRYPTO_ECHAINIV is not set
+# CONFIG_CRYPTO_HW is not set
+CONFIG_DYNAMIC_DEBUG=y
+CONFIG_DEBUG_FS=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_PREEMPT is not set
+# CONFIG_FTRACE is not set
+# CONFIG_EARLY_PRINTK is not set
diff --git a/arch/mips/configs/loongson2k_defconfig b/arch/mips/configs/loongson2k_defconfig
new file mode 100644
index 000000000..728bef666
--- /dev/null
+++ b/arch/mips/configs/loongson2k_defconfig
@@ -0,0 +1,350 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_KERNEL_LZMA=y
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_AUDIT=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_TASKSTATS=y
+CONFIG_TASK_DELAY_ACCT=y
+CONFIG_TASK_XACCT=y
+CONFIG_TASK_IO_ACCOUNTING=y
+CONFIG_MEMCG=y
+CONFIG_BLK_CGROUP=y
+CONFIG_SCHED_AUTOGROUP=y
+CONFIG_SYSFS_DEPRECATED=y
+CONFIG_RELAY=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_EMBEDDED=y
+CONFIG_MACH_LOONGSON64=y
+# CONFIG_CPU_LOONGSON3_CPUCFG_EMULATION is not set
+CONFIG_HZ_256=y
+CONFIG_MIPS32_O32=y
+CONFIG_MIPS32_N32=y
+CONFIG_MODULES=y
+CONFIG_MODULE_FORCE_LOAD=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_MQ_IOSCHED_DEADLINE=m
+CONFIG_IOSCHED_BFQ=y
+CONFIG_BFQ_GROUP_IOSCHED=y
+CONFIG_BINFMT_MISC=m
+CONFIG_KSM=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_XFRM_USER=y
+CONFIG_NET_KEY=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_MULTIPLE_TABLES=y
+CONFIG_IP_ROUTE_MULTIPATH=y
+CONFIG_IP_ROUTE_VERBOSE=y
+CONFIG_NETFILTER=y
+CONFIG_NETFILTER_NETLINK_LOG=m
+CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
+CONFIG_NETFILTER_XT_TARGET_MARK=m
+CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_MATCH_COMMENT=m
+CONFIG_NETFILTER_XT_MATCH_DCCP=m
+CONFIG_NETFILTER_XT_MATCH_ESP=m
+CONFIG_NETFILTER_XT_MATCH_LENGTH=m
+CONFIG_NETFILTER_XT_MATCH_LIMIT=m
+CONFIG_NETFILTER_XT_MATCH_MAC=m
+CONFIG_NETFILTER_XT_MATCH_MARK=m
+CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
+CONFIG_NETFILTER_XT_MATCH_QUOTA=m
+CONFIG_NETFILTER_XT_MATCH_REALM=m
+CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
+CONFIG_NETFILTER_XT_MATCH_STRING=m
+CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
+CONFIG_IP_VS=m
+CONFIG_IP_NF_IPTABLES=m
+CONFIG_IP_NF_MATCH_AH=m
+CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_TTL=m
+CONFIG_IP_NF_FILTER=m
+CONFIG_IP_NF_TARGET_REJECT=m
+CONFIG_IP_NF_MANGLE=m
+CONFIG_IP_NF_TARGET_ECN=m
+CONFIG_IP_NF_TARGET_TTL=m
+CONFIG_IP_NF_RAW=m
+CONFIG_IP_NF_ARPTABLES=m
+CONFIG_IP_NF_ARPFILTER=m
+CONFIG_IP_NF_ARP_MANGLE=m
+CONFIG_IP_SCTP=m
+CONFIG_L2TP=m
+CONFIG_BRIDGE=m
+CONFIG_CFG80211=m
+CONFIG_CFG80211_WEXT=y
+CONFIG_MAC80211=m
+CONFIG_RFKILL=m
+CONFIG_RFKILL_INPUT=y
+CONFIG_PCIEPORTBUS=y
+CONFIG_HOTPLUG_PCI_PCIE=y
+CONFIG_PCIEASPM_PERFORMANCE=y
+CONFIG_HOTPLUG_PCI=y
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+CONFIG_MTD=m
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_SIZE=8192
+CONFIG_RAID_ATTRS=m
+CONFIG_BLK_DEV_SD=y
+CONFIG_BLK_DEV_SR=y
+CONFIG_CHR_DEV_SG=y
+CONFIG_CHR_DEV_SCH=m
+CONFIG_SCSI_CONSTANTS=y
+CONFIG_SCSI_LOGGING=y
+CONFIG_SCSI_SPI_ATTRS=m
+CONFIG_SCSI_FC_ATTRS=m
+CONFIG_ISCSI_TCP=m
+CONFIG_MEGARAID_NEWGEN=y
+CONFIG_MEGARAID_MM=y
+CONFIG_MEGARAID_MAILBOX=y
+CONFIG_MEGARAID_LEGACY=y
+CONFIG_MEGARAID_SAS=y
+CONFIG_ATA=y
+CONFIG_SATA_AHCI=y
+CONFIG_PATA_ATIIXP=y
+CONFIG_MD=y
+CONFIG_BLK_DEV_MD=m
+CONFIG_MD_LINEAR=m
+CONFIG_MD_RAID0=m
+CONFIG_MD_RAID1=m
+CONFIG_MD_RAID10=m
+CONFIG_MD_RAID456=m
+CONFIG_MD_MULTIPATH=m
+CONFIG_BLK_DEV_DM=m
+CONFIG_DM_CRYPT=m
+CONFIG_DM_SNAPSHOT=m
+CONFIG_DM_MIRROR=m
+CONFIG_DM_ZERO=m
+CONFIG_TARGET_CORE=m
+CONFIG_TCM_IBLOCK=m
+CONFIG_TCM_FILEIO=m
+CONFIG_TCM_PSCSI=m
+CONFIG_LOOPBACK_TARGET=m
+CONFIG_ISCSI_TARGET=m
+CONFIG_NETDEVICES=y
+CONFIG_TUN=m
+# CONFIG_NET_VENDOR_3COM is not set
+# CONFIG_NET_VENDOR_ADAPTEC is not set
+# CONFIG_NET_VENDOR_ALTEON is not set
+# CONFIG_NET_VENDOR_AMD is not set
+# CONFIG_NET_VENDOR_ARC is not set
+# CONFIG_NET_VENDOR_ATHEROS is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_BROCADE is not set
+# CONFIG_NET_VENDOR_CHELSIO is not set
+# CONFIG_NET_VENDOR_CIRRUS is not set
+# CONFIG_NET_VENDOR_CISCO is not set
+# CONFIG_NET_VENDOR_DEC is not set
+# CONFIG_NET_VENDOR_DLINK is not set
+# CONFIG_NET_VENDOR_EMULEX is not set
+# CONFIG_NET_VENDOR_I825XX is not set
+CONFIG_E1000=y
+CONFIG_E1000E=y
+CONFIG_IGB=y
+CONFIG_IXGB=y
+CONFIG_IXGBE=y
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MELLANOX is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_MICROCHIP is not set
+# CONFIG_NET_VENDOR_MICROSEMI is not set
+# CONFIG_NET_VENDOR_MYRI is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_NETERION is not set
+# CONFIG_NET_VENDOR_NETRONOME is not set
+# CONFIG_NET_VENDOR_NI is not set
+# CONFIG_NET_VENDOR_NVIDIA is not set
+# CONFIG_NET_VENDOR_OKI is not set
+# CONFIG_NET_VENDOR_PACKET_ENGINES is not set
+# CONFIG_NET_VENDOR_PENSANDO is not set
+# CONFIG_NET_VENDOR_QLOGIC is not set
+# CONFIG_NET_VENDOR_QUALCOMM is not set
+# CONFIG_NET_VENDOR_RDC is not set
+CONFIG_8139CP=y
+CONFIG_8139TOO=y
+# CONFIG_8139TOO_PIO is not set
+CONFIG_R8169=y
+# CONFIG_NET_VENDOR_RENESAS is not set
+# CONFIG_NET_VENDOR_ROCKER is not set
+# CONFIG_NET_VENDOR_SAMSUNG is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SOLARFLARE is not set
+# CONFIG_NET_VENDOR_SILAN is not set
+# CONFIG_NET_VENDOR_SIS is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+CONFIG_STMMAC_ETH=y
+# CONFIG_NET_VENDOR_SUN is not set
+# CONFIG_NET_VENDOR_TEHUTI is not set
+# CONFIG_NET_VENDOR_TI is not set
+# CONFIG_NET_VENDOR_TOSHIBA is not set
+# CONFIG_NET_VENDOR_VIA is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+CONFIG_PPP=m
+CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_FILTER=y
+CONFIG_PPP_MPPE=m
+CONFIG_PPP_MULTILINK=y
+CONFIG_PPPOE=m
+CONFIG_PPPOL2TP=m
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
+CONFIG_ATH9K=m
+CONFIG_HOSTAP=m
+CONFIG_INPUT_LEDS=m
+CONFIG_INPUT_SPARSEKMAP=y
+CONFIG_INPUT_EVDEV=y
+# CONFIG_KEYBOARD_ATKBD is not set
+CONFIG_KEYBOARD_XTKBD=m
+# CONFIG_MOUSE_PS2 is not set
+CONFIG_INPUT_MISC=y
+CONFIG_INPUT_UINPUT=m
+# CONFIG_SERIO_I8042 is not set
+CONFIG_SERIO_SERPORT=m
+CONFIG_SERIO_LIBPS2=y
+CONFIG_SERIO_RAW=m
+CONFIG_LEGACY_PTY_COUNT=16
+CONFIG_SERIAL_8250=y
+# CONFIG_SERIAL_8250_16550A_VARIANTS is not set
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=16
+CONFIG_SERIAL_8250_EXTENDED=y
+CONFIG_SERIAL_8250_MANY_PORTS=y
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+CONFIG_SERIAL_8250_RSA=y
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_SERIAL_NONSTANDARD=y
+CONFIG_HW_RANDOM=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_PIIX4=y
+CONFIG_GPIO_LOONGSON=y
+CONFIG_SENSORS_LM75=m
+CONFIG_SENSORS_LM93=m
+CONFIG_SENSORS_W83627HF=m
+# CONFIG_MEDIA_CEC_SUPPORT is not set
+CONFIG_MEDIA_SUPPORT=m
+# CONFIG_MEDIA_CONTROLLER is not set
+CONFIG_MEDIA_USB_SUPPORT=y
+CONFIG_USB_VIDEO_CLASS=m
+CONFIG_DRM=y
+CONFIG_DRM_RADEON=y
+CONFIG_FB_RADEON=y
+CONFIG_LCD_CLASS_DEVICE=y
+CONFIG_LCD_PLATFORM=m
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
+CONFIG_LOGO=y
+CONFIG_SOUND=y
+CONFIG_SND=y
+CONFIG_SND_VERBOSE_PRINTK=y
+CONFIG_SND_SEQUENCER=y
+CONFIG_SND_SEQ_DUMMY=m
+# CONFIG_SND_ISA is not set
+CONFIG_SND_HDA_INTEL=y
+CONFIG_SND_HDA_HWDEP=y
+CONFIG_SND_HDA_PATCH_LOADER=y
+CONFIG_SND_HDA_CODEC_REALTEK=y
+CONFIG_SND_HDA_CODEC_ANALOG=y
+CONFIG_SND_HDA_CODEC_SIGMATEL=y
+CONFIG_SND_HDA_CODEC_VIA=y
+CONFIG_SND_HDA_CODEC_CONEXANT=y
+# CONFIG_SND_USB is not set
+CONFIG_SND_SOC=y
+CONFIG_HID_A4TECH=m
+CONFIG_HID_SUNPLUS=m
+CONFIG_USB=y
+CONFIG_USB_MON=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_ROOT_HUB_TT=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_UHCI_HCD=m
+CONFIG_USB_STORAGE=y
+CONFIG_USB_SERIAL=m
+CONFIG_USB_SERIAL_OPTION=m
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_CMOS=y
+CONFIG_DMADEVICES=y
+# CONFIG_CPU_HWMON is not set
+CONFIG_PM_DEVFREQ=y
+CONFIG_DEVFREQ_GOV_SIMPLE_ONDEMAND=y
+CONFIG_DEVFREQ_GOV_PERFORMANCE=y
+CONFIG_DEVFREQ_GOV_POWERSAVE=y
+CONFIG_DEVFREQ_GOV_USERSPACE=y
+CONFIG_EXT2_FS=y
+CONFIG_EXT2_FS_XATTR=y
+CONFIG_EXT2_FS_POSIX_ACL=y
+CONFIG_EXT2_FS_SECURITY=y
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_POSIX_ACL=y
+CONFIG_EXT3_FS_SECURITY=y
+CONFIG_XFS_FS=y
+CONFIG_XFS_QUOTA=y
+CONFIG_XFS_POSIX_ACL=y
+CONFIG_QUOTA=y
+# CONFIG_PRINT_QUOTA_WARNING is not set
+CONFIG_AUTOFS4_FS=y
+CONFIG_FUSE_FS=m
+CONFIG_ISO9660_FS=m
+CONFIG_JOLIET=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_CODEPAGE=936
+CONFIG_FAT_DEFAULT_IOCHARSET="gb2312"
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_CRAMFS=m
+CONFIG_SQUASHFS=y
+CONFIG_SQUASHFS_XATTR=y
+CONFIG_NFS_FS=m
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_V4=m
+CONFIG_NFSD=m
+CONFIG_NFSD_V3_ACL=y
+CONFIG_NFSD_V4=y
+CONFIG_CIFS=m
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_936=y
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_UTF8=y
+CONFIG_SECURITY=y
+CONFIG_SECURITYFS=y
+CONFIG_SECURITY_NETWORK=y
+CONFIG_SECURITY_PATH=y
+CONFIG_SECURITY_SELINUX=y
+CONFIG_SECURITY_SELINUX_BOOTPARAM=y
+CONFIG_SECURITY_SELINUX_DISABLE=y
+CONFIG_DEFAULT_SECURITY_DAC=y
+CONFIG_CRYPTO_SEQIV=m
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_MD5=y
+CONFIG_CRYPTO_WP512=m
+CONFIG_CRYPTO_BLOWFISH=m
+CONFIG_CRYPTO_CAST5=m
+CONFIG_CRYPTO_CAST6=m
+CONFIG_CRYPTO_SERPENT=m
+CONFIG_CRYPTO_TWOFISH=m
+CONFIG_CRYPTO_DEFLATE=m
+CONFIG_PRINTK_TIME=y
+CONFIG_FRAME_WARN=1024
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_PREEMPT is not set
+# CONFIG_FTRACE is not set
diff --git a/arch/mips/configs/loongson3_defconfig b/arch/mips/configs/loongson3_defconfig
new file mode 100644
index 000000000..aca66a5f3
--- /dev/null
+++ b/arch/mips/configs/loongson3_defconfig
@@ -0,0 +1,406 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_KERNEL_LZMA=y
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_AUDIT=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_TASKSTATS=y
+CONFIG_TASK_DELAY_ACCT=y
+CONFIG_TASK_XACCT=y
+CONFIG_TASK_IO_ACCOUNTING=y
+CONFIG_MEMCG=y
+CONFIG_BLK_CGROUP=y
+CONFIG_CGROUP_PIDS=y
+CONFIG_CGROUP_FREEZER=y
+CONFIG_CPUSETS=y
+CONFIG_CGROUP_DEVICE=y
+CONFIG_CGROUP_CPUACCT=y
+CONFIG_NAMESPACES=y
+CONFIG_USER_NS=y
+CONFIG_SCHED_AUTOGROUP=y
+CONFIG_SYSFS_DEPRECATED=y
+CONFIG_RELAY=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_BPF_SYSCALL=y
+CONFIG_EMBEDDED=y
+CONFIG_PERF_EVENTS=y
+CONFIG_MACH_LOONGSON64=y
+CONFIG_CPU_HAS_MSA=y
+CONFIG_NUMA=y
+CONFIG_NR_CPUS=16
+CONFIG_HZ_256=y
+CONFIG_KEXEC=y
+CONFIG_MIPS32_O32=y
+CONFIG_MIPS32_N32=y
+CONFIG_VIRTUALIZATION=y
+CONFIG_KVM=m
+CONFIG_KPROBES=y
+CONFIG_MODULES=y
+CONFIG_MODULE_FORCE_LOAD=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_MQ_IOSCHED_DEADLINE=m
+CONFIG_IOSCHED_BFQ=y
+CONFIG_BFQ_GROUP_IOSCHED=y
+CONFIG_BINFMT_MISC=m
+CONFIG_KSM=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_XFRM_USER=y
+CONFIG_NET_KEY=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_MULTIPLE_TABLES=y
+CONFIG_IP_ROUTE_MULTIPATH=y
+CONFIG_IP_ROUTE_VERBOSE=y
+CONFIG_NETFILTER=y
+CONFIG_BRIDGE_NETFILTER=m
+CONFIG_NETFILTER_NETLINK_LOG=m
+CONFIG_NF_CONNTRACK=m
+CONFIG_NF_CONNTRACK_SNMP=m
+CONFIG_NF_TABLES=m
+CONFIG_NFT_CT=m
+CONFIG_NFT_NAT=m
+CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
+CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
+CONFIG_NETFILTER_XT_TARGET_MARK=m
+CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_MATCH_COMMENT=m
+CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+CONFIG_NETFILTER_XT_MATCH_DCCP=m
+CONFIG_NETFILTER_XT_MATCH_ESP=m
+CONFIG_NETFILTER_XT_MATCH_LENGTH=m
+CONFIG_NETFILTER_XT_MATCH_LIMIT=m
+CONFIG_NETFILTER_XT_MATCH_MAC=m
+CONFIG_NETFILTER_XT_MATCH_MARK=m
+CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
+CONFIG_NETFILTER_XT_MATCH_QUOTA=m
+CONFIG_NETFILTER_XT_MATCH_REALM=m
+CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
+CONFIG_NETFILTER_XT_MATCH_STRING=m
+CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
+CONFIG_IP_SET=m
+CONFIG_IP_VS=m
+CONFIG_NF_TABLES_IPV4=y
+CONFIG_NF_TABLES_ARP=y
+CONFIG_IP_NF_IPTABLES=m
+CONFIG_IP_NF_MATCH_AH=m
+CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_RPFILTER=m
+CONFIG_IP_NF_MATCH_TTL=m
+CONFIG_IP_NF_FILTER=m
+CONFIG_IP_NF_TARGET_REJECT=m
+CONFIG_IP_NF_NAT=m
+CONFIG_IP_NF_TARGET_MASQUERADE=m
+CONFIG_IP_NF_MANGLE=m
+CONFIG_IP_NF_TARGET_ECN=m
+CONFIG_IP_NF_TARGET_TTL=m
+CONFIG_IP_NF_RAW=m
+CONFIG_IP_NF_SECURITY=m
+CONFIG_IP_NF_ARPTABLES=m
+CONFIG_IP_NF_ARPFILTER=m
+CONFIG_IP_NF_ARP_MANGLE=m
+CONFIG_NF_TABLES_IPV6=y
+CONFIG_IP6_NF_IPTABLES=m
+CONFIG_IP6_NF_MATCH_RPFILTER=m
+CONFIG_IP6_NF_FILTER=m
+CONFIG_IP6_NF_TARGET_REJECT=m
+CONFIG_IP6_NF_MANGLE=m
+CONFIG_IP6_NF_RAW=m
+CONFIG_IP6_NF_SECURITY=m
+CONFIG_IP6_NF_NAT=m
+CONFIG_IP6_NF_TARGET_MASQUERADE=m
+CONFIG_NF_TABLES_BRIDGE=m
+CONFIG_BRIDGE_NF_EBTABLES=m
+CONFIG_BRIDGE_EBT_T_FILTER=m
+CONFIG_BRIDGE_EBT_T_NAT=m
+CONFIG_IP_SCTP=m
+CONFIG_L2TP=m
+CONFIG_BRIDGE=m
+CONFIG_VSOCKETS=m
+CONFIG_VIRTIO_VSOCKETS=m
+CONFIG_BPF_JIT=y
+CONFIG_CFG80211=m
+CONFIG_CFG80211_WEXT=y
+CONFIG_MAC80211=m
+CONFIG_RFKILL=m
+CONFIG_RFKILL_INPUT=y
+CONFIG_NET_9P=m
+CONFIG_NET_9P_VIRTIO=m
+CONFIG_PCIEPORTBUS=y
+# CONFIG_PCIEASPM is not set
+CONFIG_HOTPLUG_PCI=y
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+CONFIG_MTD=m
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_SIZE=8192
+CONFIG_VIRTIO_BLK=y
+CONFIG_RAID_ATTRS=m
+CONFIG_BLK_DEV_SD=y
+CONFIG_BLK_DEV_SR=y
+CONFIG_CHR_DEV_SG=y
+CONFIG_CHR_DEV_SCH=m
+CONFIG_SCSI_CONSTANTS=y
+CONFIG_SCSI_LOGGING=y
+CONFIG_SCSI_SPI_ATTRS=m
+CONFIG_SCSI_FC_ATTRS=m
+CONFIG_ISCSI_TCP=m
+CONFIG_MEGARAID_NEWGEN=y
+CONFIG_MEGARAID_MM=y
+CONFIG_MEGARAID_MAILBOX=y
+CONFIG_MEGARAID_LEGACY=y
+CONFIG_MEGARAID_SAS=y
+CONFIG_SCSI_VIRTIO=y
+CONFIG_ATA=y
+CONFIG_SATA_AHCI=y
+CONFIG_PATA_ATIIXP=y
+CONFIG_MD=y
+CONFIG_BLK_DEV_MD=m
+CONFIG_MD_LINEAR=m
+CONFIG_MD_RAID0=m
+CONFIG_MD_RAID1=m
+CONFIG_MD_RAID10=m
+CONFIG_MD_RAID456=m
+CONFIG_MD_MULTIPATH=m
+CONFIG_BLK_DEV_DM=m
+CONFIG_DM_CRYPT=m
+CONFIG_DM_SNAPSHOT=m
+CONFIG_DM_MIRROR=m
+CONFIG_DM_ZERO=m
+CONFIG_TARGET_CORE=m
+CONFIG_TCM_IBLOCK=m
+CONFIG_TCM_FILEIO=m
+CONFIG_TCM_PSCSI=m
+CONFIG_LOOPBACK_TARGET=m
+CONFIG_ISCSI_TARGET=m
+CONFIG_NETDEVICES=y
+CONFIG_DUMMY=m
+CONFIG_TUN=m
+CONFIG_VETH=m
+CONFIG_VIRTIO_NET=m
+# CONFIG_NET_VENDOR_3COM is not set
+# CONFIG_NET_VENDOR_ADAPTEC is not set
+# CONFIG_NET_VENDOR_ALTEON is not set
+# CONFIG_NET_VENDOR_AMD is not set
+# CONFIG_NET_VENDOR_ARC is not set
+# CONFIG_NET_VENDOR_ATHEROS is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_BROCADE is not set
+# CONFIG_NET_VENDOR_CHELSIO is not set
+# CONFIG_NET_VENDOR_CIRRUS is not set
+# CONFIG_NET_VENDOR_CISCO is not set
+# CONFIG_NET_VENDOR_DEC is not set
+# CONFIG_NET_VENDOR_DLINK is not set
+# CONFIG_NET_VENDOR_EMULEX is not set
+# CONFIG_NET_VENDOR_I825XX is not set
+CONFIG_E1000=y
+CONFIG_E1000E=y
+CONFIG_IGB=y
+CONFIG_IXGB=y
+CONFIG_IXGBE=y
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MELLANOX is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_MYRI is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_NVIDIA is not set
+# CONFIG_NET_VENDOR_OKI is not set
+# CONFIG_NET_VENDOR_QLOGIC is not set
+# CONFIG_NET_VENDOR_RDC is not set
+CONFIG_8139CP=m
+CONFIG_8139TOO=m
+CONFIG_R8169=y
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SILAN is not set
+# CONFIG_NET_VENDOR_SIS is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_SUN is not set
+# CONFIG_NET_VENDOR_TEHUTI is not set
+# CONFIG_NET_VENDOR_TI is not set
+# CONFIG_NET_VENDOR_TOSHIBA is not set
+# CONFIG_NET_VENDOR_VIA is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+CONFIG_PPP=m
+CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_FILTER=y
+CONFIG_PPP_MPPE=m
+CONFIG_PPP_MULTILINK=y
+CONFIG_PPPOE=m
+CONFIG_PPPOL2TP=m
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
+CONFIG_ATH9K=m
+CONFIG_HOSTAP=m
+CONFIG_INPUT_SPARSEKMAP=y
+CONFIG_INPUT_MOUSEDEV=y
+CONFIG_INPUT_MOUSEDEV_PSAUX=y
+CONFIG_INPUT_EVDEV=y
+CONFIG_KEYBOARD_XTKBD=m
+CONFIG_MOUSE_PS2_SENTELIC=y
+CONFIG_MOUSE_SERIAL=m
+CONFIG_INPUT_MISC=y
+CONFIG_INPUT_UINPUT=m
+CONFIG_SERIO_SERPORT=m
+CONFIG_SERIO_RAW=m
+CONFIG_LEGACY_PTY_COUNT=16
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=16
+CONFIG_SERIAL_8250_EXTENDED=y
+CONFIG_SERIAL_8250_MANY_PORTS=y
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+CONFIG_SERIAL_8250_RSA=y
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_SERIAL_NONSTANDARD=y
+CONFIG_VIRTIO_CONSOLE=y
+CONFIG_HW_RANDOM=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_PIIX4=y
+CONFIG_GPIO_LOONGSON=y
+CONFIG_SENSORS_LM75=m
+CONFIG_SENSORS_LM93=m
+CONFIG_SENSORS_W83627HF=m
+CONFIG_MEDIA_SUPPORT=m
+CONFIG_MEDIA_USB_SUPPORT=y
+CONFIG_USB_VIDEO_CLASS=m
+CONFIG_DRM=y
+CONFIG_DRM_RADEON=m
+CONFIG_DRM_QXL=y
+CONFIG_DRM_VIRTIO_GPU=y
+CONFIG_FB=y
+CONFIG_FB_RADEON=y
+CONFIG_LCD_CLASS_DEVICE=y
+CONFIG_LCD_PLATFORM=m
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
+CONFIG_LOGO=y
+CONFIG_SOUND=y
+CONFIG_SND=m
+CONFIG_SND_SEQUENCER=m
+CONFIG_SND_SEQ_DUMMY=m
+# CONFIG_SND_ISA is not set
+CONFIG_SND_HDA_INTEL=m
+CONFIG_SND_HDA_PATCH_LOADER=y
+CONFIG_SND_HDA_CODEC_REALTEK=m
+CONFIG_SND_HDA_CODEC_SIGMATEL=m
+CONFIG_SND_HDA_CODEC_HDMI=m
+CONFIG_SND_HDA_CODEC_CONEXANT=m
+# CONFIG_SND_USB is not set
+CONFIG_HIDRAW=y
+CONFIG_HID_A4TECH=m
+CONFIG_HID_SUNPLUS=m
+CONFIG_HID_PID=y
+CONFIG_USB_HIDDEV=y
+CONFIG_USB=y
+CONFIG_USB_MON=y
+CONFIG_USB_XHCI_HCD=m
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_ROOT_HUB_TT=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_UHCI_HCD=m
+CONFIG_USB_STORAGE=m
+CONFIG_USB_SERIAL=m
+CONFIG_USB_SERIAL_PL2303=m
+CONFIG_USB_SERIAL_OPTION=m
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_CMOS=y
+CONFIG_RTC_DRV_GOLDFISH=y
+CONFIG_DMADEVICES=y
+CONFIG_VIRTIO_PCI=y
+CONFIG_VIRTIO_BALLOON=m
+CONFIG_VIRTIO_INPUT=y
+CONFIG_VIRTIO_MMIO=y
+CONFIG_VHOST_NET=m
+CONFIG_VHOST_SCSI=m
+CONFIG_VHOST_VSOCK=m
+CONFIG_GOLDFISH=y
+CONFIG_PM_DEVFREQ=y
+CONFIG_DEVFREQ_GOV_SIMPLE_ONDEMAND=y
+CONFIG_DEVFREQ_GOV_PERFORMANCE=y
+CONFIG_DEVFREQ_GOV_POWERSAVE=y
+CONFIG_DEVFREQ_GOV_USERSPACE=y
+CONFIG_EXT2_FS=y
+CONFIG_EXT2_FS_XATTR=y
+CONFIG_EXT2_FS_POSIX_ACL=y
+CONFIG_EXT2_FS_SECURITY=y
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_POSIX_ACL=y
+CONFIG_EXT3_FS_SECURITY=y
+CONFIG_XFS_FS=y
+CONFIG_XFS_POSIX_ACL=y
+CONFIG_QUOTA=y
+# CONFIG_PRINT_QUOTA_WARNING is not set
+CONFIG_QFMT_V1=m
+CONFIG_QFMT_V2=m
+CONFIG_AUTOFS4_FS=y
+CONFIG_FUSE_FS=m
+CONFIG_VIRTIO_FS=m
+CONFIG_FSCACHE=m
+CONFIG_ISO9660_FS=m
+CONFIG_JOLIET=y
+CONFIG_MSDOS_FS=m
+CONFIG_VFAT_FS=m
+CONFIG_FAT_DEFAULT_CODEPAGE=936
+CONFIG_FAT_DEFAULT_IOCHARSET="gb2312"
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_CRAMFS=m
+CONFIG_SQUASHFS=y
+CONFIG_SQUASHFS_XATTR=y
+CONFIG_NFS_FS=m
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_V4=m
+CONFIG_NFSD=m
+CONFIG_NFSD_V3_ACL=y
+CONFIG_NFSD_V4=y
+CONFIG_CIFS=m
+CONFIG_9P_FS=m
+CONFIG_9P_FSCACHE=y
+CONFIG_9P_FS_POSIX_ACL=y
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_936=y
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_UTF8=y
+CONFIG_SECURITY=y
+CONFIG_SECURITYFS=y
+CONFIG_SECURITY_NETWORK=y
+CONFIG_SECURITY_PATH=y
+CONFIG_SECURITY_SELINUX=y
+CONFIG_SECURITY_SELINUX_BOOTPARAM=y
+CONFIG_SECURITY_SELINUX_DISABLE=y
+CONFIG_DEFAULT_SECURITY_DAC=y
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_MD5=y
+CONFIG_CRYPTO_WP512=m
+CONFIG_CRYPTO_BLOWFISH=m
+CONFIG_CRYPTO_CAST5=m
+CONFIG_CRYPTO_CAST6=m
+CONFIG_CRYPTO_SERPENT=m
+CONFIG_CRYPTO_TWOFISH=m
+CONFIG_CRYPTO_DEFLATE=m
+CONFIG_PRINTK_TIME=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_FS=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_PREEMPT is not set
+CONFIG_FUNCTION_TRACER=y
+CONFIG_FTRACE_SYSCALLS=y
+CONFIG_CMDLINE_BOOL=y
+CONFIG_CMDLINE="ieee754=relaxed"
diff --git a/arch/mips/configs/malta_defconfig b/arch/mips/configs/malta_defconfig
new file mode 100644
index 000000000..265d38dff
--- /dev/null
+++ b/arch/mips/configs/malta_defconfig
@@ -0,0 +1,417 @@
+CONFIG_SYSVIPC=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_LOG_BUF_SHIFT=15
+CONFIG_NAMESPACES=y
+CONFIG_RELAY=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_EXPERT=y
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_MIPS_MALTA=y
+CONFIG_CPU_LITTLE_ENDIAN=y
+CONFIG_CPU_MIPS32_R2=y
+CONFIG_PAGE_SIZE_16KB=y
+CONFIG_NR_CPUS=8
+CONFIG_HZ_100=y
+CONFIG_PCI=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_XFRM_USER=m
+CONFIG_NET_KEY=y
+CONFIG_NET_KEY_MIGRATE=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_MULTIPLE_TABLES=y
+CONFIG_IP_ROUTE_MULTIPATH=y
+CONFIG_IP_ROUTE_VERBOSE=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_NET_IPIP=m
+CONFIG_IP_MROUTE=y
+CONFIG_IP_PIMSM_V1=y
+CONFIG_IP_PIMSM_V2=y
+CONFIG_SYN_COOKIES=y
+CONFIG_INET_AH=m
+CONFIG_INET_ESP=m
+CONFIG_INET_IPCOMP=m
+CONFIG_TCP_MD5SIG=y
+CONFIG_IPV6_ROUTER_PREF=y
+CONFIG_IPV6_ROUTE_INFO=y
+CONFIG_IPV6_OPTIMISTIC_DAD=y
+CONFIG_INET6_AH=m
+CONFIG_INET6_ESP=m
+CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_TUNNEL=m
+CONFIG_IPV6_MROUTE=y
+CONFIG_IPV6_PIMSM_V2=y
+CONFIG_NETWORK_SECMARK=y
+CONFIG_NETFILTER=y
+CONFIG_NF_CONNTRACK=m
+CONFIG_NF_CONNTRACK_SECMARK=y
+CONFIG_NF_CONNTRACK_EVENTS=y
+CONFIG_NF_CONNTRACK_AMANDA=m
+CONFIG_NF_CONNTRACK_FTP=m
+CONFIG_NF_CONNTRACK_H323=m
+CONFIG_NF_CONNTRACK_IRC=m
+CONFIG_NF_CONNTRACK_PPTP=m
+CONFIG_NF_CONNTRACK_SANE=m
+CONFIG_NF_CONNTRACK_SIP=m
+CONFIG_NF_CONNTRACK_TFTP=m
+CONFIG_NF_CT_NETLINK=m
+CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
+CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
+CONFIG_NETFILTER_XT_TARGET_MARK=m
+CONFIG_NETFILTER_XT_TARGET_NFLOG=m
+CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_TARGET_TPROXY=m
+CONFIG_NETFILTER_XT_TARGET_TRACE=m
+CONFIG_NETFILTER_XT_TARGET_SECMARK=m
+CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
+CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP=m
+CONFIG_NETFILTER_XT_MATCH_COMMENT=m
+CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
+CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
+CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
+CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+CONFIG_NETFILTER_XT_MATCH_DCCP=m
+CONFIG_NETFILTER_XT_MATCH_ESP=m
+CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
+CONFIG_NETFILTER_XT_MATCH_HELPER=m
+CONFIG_NETFILTER_XT_MATCH_IPRANGE=m
+CONFIG_NETFILTER_XT_MATCH_LENGTH=m
+CONFIG_NETFILTER_XT_MATCH_LIMIT=m
+CONFIG_NETFILTER_XT_MATCH_MAC=m
+CONFIG_NETFILTER_XT_MATCH_MARK=m
+CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_OWNER=m
+CONFIG_NETFILTER_XT_MATCH_POLICY=m
+CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
+CONFIG_NETFILTER_XT_MATCH_QUOTA=m
+CONFIG_NETFILTER_XT_MATCH_RATEEST=m
+CONFIG_NETFILTER_XT_MATCH_REALM=m
+CONFIG_NETFILTER_XT_MATCH_RECENT=m
+CONFIG_NETFILTER_XT_MATCH_SOCKET=m
+CONFIG_NETFILTER_XT_MATCH_STATE=m
+CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
+CONFIG_NETFILTER_XT_MATCH_STRING=m
+CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
+CONFIG_NETFILTER_XT_MATCH_TIME=m
+CONFIG_NETFILTER_XT_MATCH_U32=m
+CONFIG_IP_VS=m
+CONFIG_IP_VS_IPV6=y
+CONFIG_IP_VS_PROTO_TCP=y
+CONFIG_IP_VS_PROTO_UDP=y
+CONFIG_IP_VS_PROTO_ESP=y
+CONFIG_IP_VS_PROTO_AH=y
+CONFIG_IP_VS_RR=m
+CONFIG_IP_VS_WRR=m
+CONFIG_IP_VS_LC=m
+CONFIG_IP_VS_WLC=m
+CONFIG_IP_VS_LBLC=m
+CONFIG_IP_VS_LBLCR=m
+CONFIG_IP_VS_DH=m
+CONFIG_IP_VS_SH=m
+CONFIG_IP_VS_SED=m
+CONFIG_IP_VS_NQ=m
+CONFIG_IP_NF_IPTABLES=m
+CONFIG_IP_NF_MATCH_AH=m
+CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_TTL=m
+CONFIG_IP_NF_FILTER=m
+CONFIG_IP_NF_TARGET_REJECT=m
+CONFIG_IP_NF_MANGLE=m
+CONFIG_IP_NF_TARGET_CLUSTERIP=m
+CONFIG_IP_NF_TARGET_ECN=m
+CONFIG_IP_NF_TARGET_TTL=m
+CONFIG_IP_NF_RAW=m
+CONFIG_IP_NF_ARPTABLES=m
+CONFIG_IP_NF_ARPFILTER=m
+CONFIG_IP_NF_ARP_MANGLE=m
+CONFIG_IP6_NF_MATCH_AH=m
+CONFIG_IP6_NF_MATCH_EUI64=m
+CONFIG_IP6_NF_MATCH_FRAG=m
+CONFIG_IP6_NF_MATCH_OPTS=m
+CONFIG_IP6_NF_MATCH_HL=m
+CONFIG_IP6_NF_MATCH_IPV6HEADER=m
+CONFIG_IP6_NF_MATCH_MH=m
+CONFIG_IP6_NF_MATCH_RT=m
+CONFIG_IP6_NF_TARGET_HL=m
+CONFIG_IP6_NF_FILTER=m
+CONFIG_IP6_NF_TARGET_REJECT=m
+CONFIG_IP6_NF_MANGLE=m
+CONFIG_IP6_NF_RAW=m
+CONFIG_BRIDGE_NF_EBTABLES=m
+CONFIG_BRIDGE_EBT_BROUTE=m
+CONFIG_BRIDGE_EBT_T_FILTER=m
+CONFIG_BRIDGE_EBT_T_NAT=m
+CONFIG_BRIDGE_EBT_802_3=m
+CONFIG_BRIDGE_EBT_AMONG=m
+CONFIG_BRIDGE_EBT_ARP=m
+CONFIG_BRIDGE_EBT_IP=m
+CONFIG_BRIDGE_EBT_IP6=m
+CONFIG_BRIDGE_EBT_LIMIT=m
+CONFIG_BRIDGE_EBT_MARK=m
+CONFIG_BRIDGE_EBT_PKTTYPE=m
+CONFIG_BRIDGE_EBT_STP=m
+CONFIG_BRIDGE_EBT_VLAN=m
+CONFIG_BRIDGE_EBT_ARPREPLY=m
+CONFIG_BRIDGE_EBT_DNAT=m
+CONFIG_BRIDGE_EBT_MARK_T=m
+CONFIG_BRIDGE_EBT_REDIRECT=m
+CONFIG_BRIDGE_EBT_SNAT=m
+CONFIG_BRIDGE_EBT_LOG=m
+CONFIG_BRIDGE_EBT_NFLOG=m
+CONFIG_IP_SCTP=m
+CONFIG_BRIDGE=m
+CONFIG_VLAN_8021Q=m
+CONFIG_VLAN_8021Q_GVRP=y
+CONFIG_ATALK=m
+CONFIG_DEV_APPLETALK=m
+CONFIG_IPDDP=m
+CONFIG_IPDDP_ENCAP=y
+CONFIG_PHONET=m
+CONFIG_NET_SCHED=y
+CONFIG_NET_SCH_CBQ=m
+CONFIG_NET_SCH_HTB=m
+CONFIG_NET_SCH_HFSC=m
+CONFIG_NET_SCH_PRIO=m
+CONFIG_NET_SCH_RED=m
+CONFIG_NET_SCH_SFQ=m
+CONFIG_NET_SCH_TEQL=m
+CONFIG_NET_SCH_TBF=m
+CONFIG_NET_SCH_GRED=m
+CONFIG_NET_SCH_DSMARK=m
+CONFIG_NET_SCH_NETEM=m
+CONFIG_NET_SCH_INGRESS=m
+CONFIG_NET_CLS_BASIC=m
+CONFIG_NET_CLS_TCINDEX=m
+CONFIG_NET_CLS_ROUTE4=m
+CONFIG_NET_CLS_FW=m
+CONFIG_NET_CLS_U32=m
+CONFIG_NET_CLS_RSVP=m
+CONFIG_NET_CLS_RSVP6=m
+CONFIG_NET_CLS_FLOW=m
+CONFIG_NET_CLS_ACT=y
+CONFIG_NET_ACT_POLICE=y
+CONFIG_NET_ACT_GACT=m
+CONFIG_GACT_PROB=y
+CONFIG_NET_ACT_MIRRED=m
+CONFIG_NET_ACT_IPT=m
+CONFIG_NET_ACT_NAT=m
+CONFIG_NET_ACT_PEDIT=m
+CONFIG_NET_ACT_SIMP=m
+CONFIG_NET_ACT_SKBEDIT=m
+CONFIG_CFG80211=m
+CONFIG_MAC80211=m
+CONFIG_MAC80211_MESH=y
+CONFIG_RFKILL=m
+CONFIG_DEVTMPFS=y
+CONFIG_CONNECTOR=m
+CONFIG_MTD=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_OOPS=m
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_CFI_STAA=y
+CONFIG_MTD_PHYSMAP_OF=y
+CONFIG_MTD_UBI=m
+CONFIG_MTD_UBI_GLUEBI=m
+CONFIG_BLK_DEV_FD=m
+CONFIG_BLK_DEV_LOOP=m
+CONFIG_BLK_DEV_NBD=m
+CONFIG_BLK_DEV_RAM=y
+CONFIG_CDROM_PKTCDVD=m
+CONFIG_ATA_OVER_ETH=m
+CONFIG_RAID_ATTRS=m
+CONFIG_BLK_DEV_SD=y
+CONFIG_CHR_DEV_ST=m
+CONFIG_BLK_DEV_SR=y
+CONFIG_CHR_DEV_SG=m
+CONFIG_SCSI_CONSTANTS=y
+CONFIG_SCSI_LOGGING=y
+CONFIG_SCSI_SCAN_ASYNC=y
+CONFIG_SCSI_FC_ATTRS=m
+CONFIG_ISCSI_TCP=m
+CONFIG_BLK_DEV_3W_XXXX_RAID=m
+CONFIG_SCSI_3W_9XXX=m
+CONFIG_SCSI_ACARD=m
+CONFIG_SCSI_AACRAID=m
+CONFIG_SCSI_AIC7XXX=m
+CONFIG_AIC7XXX_RESET_DELAY_MS=15000
+# CONFIG_AIC7XXX_DEBUG_ENABLE is not set
+CONFIG_ATA=y
+CONFIG_ATA_PIIX=y
+CONFIG_PATA_LEGACY=y
+CONFIG_MD=y
+CONFIG_BLK_DEV_MD=m
+CONFIG_MD_LINEAR=m
+CONFIG_MD_RAID0=m
+CONFIG_MD_RAID1=m
+CONFIG_MD_RAID10=m
+CONFIG_MD_RAID456=m
+CONFIG_MD_MULTIPATH=m
+CONFIG_MD_FAULTY=m
+CONFIG_BLK_DEV_DM=m
+CONFIG_DM_CRYPT=m
+CONFIG_DM_SNAPSHOT=m
+CONFIG_DM_MIRROR=m
+CONFIG_DM_ZERO=m
+CONFIG_DM_MULTIPATH=m
+CONFIG_NETDEVICES=y
+CONFIG_BONDING=m
+CONFIG_DUMMY=m
+CONFIG_EQUALIZER=m
+CONFIG_IFB=m
+CONFIG_MACVLAN=m
+CONFIG_TUN=m
+CONFIG_VETH=m
+# CONFIG_NET_VENDOR_3COM is not set
+CONFIG_PCNET32=y
+CONFIG_CHELSIO_T3=m
+CONFIG_AX88796=m
+CONFIG_NETXEN_NIC=m
+CONFIG_TC35815=m
+CONFIG_BROADCOM_PHY=m
+CONFIG_CICADA_PHY=m
+CONFIG_DAVICOM_PHY=m
+CONFIG_ICPLUS_PHY=m
+CONFIG_LXT_PHY=m
+CONFIG_MARVELL_PHY=m
+CONFIG_QSEMI_PHY=m
+CONFIG_REALTEK_PHY=m
+CONFIG_SMSC_PHY=m
+CONFIG_VITESSE_PHY=m
+CONFIG_ATMEL=m
+CONFIG_PCI_ATMEL=m
+CONFIG_IPW2100=m
+CONFIG_IPW2100_MONITOR=y
+CONFIG_HOSTAP=m
+CONFIG_HOSTAP_FIRMWARE=y
+CONFIG_HOSTAP_FIRMWARE_NVRAM=y
+CONFIG_HOSTAP_PLX=m
+CONFIG_HOSTAP_PCI=m
+CONFIG_LIBERTAS=m
+CONFIG_INPUT_MOUSEDEV=y
+CONFIG_MOUSE_PS2_ELANTECH=y
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_POWER_RESET=y
+CONFIG_POWER_RESET_PIIX4_POWEROFF=y
+CONFIG_POWER_RESET_SYSCON=y
+# CONFIG_HWMON is not set
+CONFIG_FB=y
+CONFIG_FB_CIRRUS=y
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_HID=m
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_CMOS=y
+CONFIG_UIO=m
+CONFIG_UIO_CIF=m
+CONFIG_EXT2_FS=y
+CONFIG_EXT3_FS=y
+CONFIG_REISERFS_FS=m
+CONFIG_REISERFS_PROC_INFO=y
+CONFIG_REISERFS_FS_XATTR=y
+CONFIG_REISERFS_FS_POSIX_ACL=y
+CONFIG_REISERFS_FS_SECURITY=y
+CONFIG_JFS_FS=m
+CONFIG_JFS_POSIX_ACL=y
+CONFIG_JFS_SECURITY=y
+CONFIG_XFS_FS=m
+CONFIG_XFS_QUOTA=y
+CONFIG_XFS_POSIX_ACL=y
+CONFIG_QUOTA=y
+CONFIG_QFMT_V2=y
+CONFIG_FUSE_FS=m
+CONFIG_ISO9660_FS=m
+CONFIG_JOLIET=y
+CONFIG_ZISOFS=y
+CONFIG_UDF_FS=m
+CONFIG_MSDOS_FS=m
+CONFIG_VFAT_FS=m
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_AFFS_FS=m
+CONFIG_HFS_FS=m
+CONFIG_HFSPLUS_FS=m
+CONFIG_BEFS_FS=m
+CONFIG_BFS_FS=m
+CONFIG_EFS_FS=m
+CONFIG_JFFS2_FS=m
+CONFIG_JFFS2_FS_XATTR=y
+CONFIG_JFFS2_COMPRESSION_OPTIONS=y
+CONFIG_JFFS2_RUBIN=y
+CONFIG_CRAMFS=m
+CONFIG_VXFS_FS=m
+CONFIG_MINIX_FS=m
+CONFIG_ROMFS_FS=m
+CONFIG_SYSV_FS=m
+CONFIG_UFS_FS=m
+CONFIG_NFS_FS=y
+CONFIG_ROOT_NFS=y
+CONFIG_NFSD=y
+CONFIG_NLS_CODEPAGE_437=m
+CONFIG_NLS_CODEPAGE_737=m
+CONFIG_NLS_CODEPAGE_775=m
+CONFIG_NLS_CODEPAGE_850=m
+CONFIG_NLS_CODEPAGE_852=m
+CONFIG_NLS_CODEPAGE_855=m
+CONFIG_NLS_CODEPAGE_857=m
+CONFIG_NLS_CODEPAGE_860=m
+CONFIG_NLS_CODEPAGE_861=m
+CONFIG_NLS_CODEPAGE_862=m
+CONFIG_NLS_CODEPAGE_863=m
+CONFIG_NLS_CODEPAGE_864=m
+CONFIG_NLS_CODEPAGE_865=m
+CONFIG_NLS_CODEPAGE_866=m
+CONFIG_NLS_CODEPAGE_869=m
+CONFIG_NLS_CODEPAGE_936=m
+CONFIG_NLS_CODEPAGE_950=m
+CONFIG_NLS_CODEPAGE_932=m
+CONFIG_NLS_CODEPAGE_949=m
+CONFIG_NLS_CODEPAGE_874=m
+CONFIG_NLS_ISO8859_8=m
+CONFIG_NLS_CODEPAGE_1250=m
+CONFIG_NLS_CODEPAGE_1251=m
+CONFIG_NLS_ASCII=m
+CONFIG_NLS_ISO8859_1=m
+CONFIG_NLS_ISO8859_2=m
+CONFIG_NLS_ISO8859_3=m
+CONFIG_NLS_ISO8859_4=m
+CONFIG_NLS_ISO8859_5=m
+CONFIG_NLS_ISO8859_6=m
+CONFIG_NLS_ISO8859_7=m
+CONFIG_NLS_ISO8859_9=m
+CONFIG_NLS_ISO8859_13=m
+CONFIG_NLS_ISO8859_14=m
+CONFIG_NLS_ISO8859_15=m
+CONFIG_NLS_KOI8_R=m
+CONFIG_NLS_KOI8_U=m
+CONFIG_CRYPTO_CRYPTD=m
+CONFIG_CRYPTO_LRW=m
+CONFIG_CRYPTO_PCBC=m
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_XCBC=m
+CONFIG_CRYPTO_MD4=m
+CONFIG_CRYPTO_SHA512=m
+CONFIG_CRYPTO_WP512=m
+CONFIG_CRYPTO_ANUBIS=m
+CONFIG_CRYPTO_BLOWFISH=m
+CONFIG_CRYPTO_CAMELLIA=m
+CONFIG_CRYPTO_CAST5=m
+CONFIG_CRYPTO_CAST6=m
+CONFIG_CRYPTO_FCRYPT=m
+CONFIG_CRYPTO_KHAZAD=m
+CONFIG_CRYPTO_SERPENT=m
+CONFIG_CRYPTO_TEA=m
+CONFIG_CRYPTO_TWOFISH=m
diff --git a/arch/mips/configs/malta_kvm_defconfig b/arch/mips/configs/malta_kvm_defconfig
new file mode 100644
index 000000000..1d2b248c7
--- /dev/null
+++ b/arch/mips/configs/malta_kvm_defconfig
@@ -0,0 +1,426 @@
+CONFIG_SYSVIPC=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_LOG_BUF_SHIFT=15
+CONFIG_NAMESPACES=y
+CONFIG_RELAY=y
+CONFIG_EXPERT=y
+CONFIG_PERF_EVENTS=y
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_MIPS_MALTA=y
+CONFIG_CPU_LITTLE_ENDIAN=y
+CONFIG_CPU_MIPS32_R2=y
+CONFIG_PAGE_SIZE_16KB=y
+CONFIG_NR_CPUS=8
+CONFIG_HZ_100=y
+CONFIG_PCI=y
+CONFIG_VIRTUALIZATION=y
+CONFIG_KVM=m
+CONFIG_KVM_MIPS_DEBUG_COP0_COUNTERS=y
+CONFIG_VHOST_NET=m
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_XFRM_USER=m
+CONFIG_NET_KEY=y
+CONFIG_NET_KEY_MIGRATE=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_MULTIPLE_TABLES=y
+CONFIG_IP_ROUTE_MULTIPATH=y
+CONFIG_IP_ROUTE_VERBOSE=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_NET_IPIP=m
+CONFIG_IP_MROUTE=y
+CONFIG_IP_PIMSM_V1=y
+CONFIG_IP_PIMSM_V2=y
+CONFIG_SYN_COOKIES=y
+CONFIG_INET_AH=m
+CONFIG_INET_ESP=m
+CONFIG_INET_IPCOMP=m
+CONFIG_TCP_MD5SIG=y
+CONFIG_IPV6_ROUTER_PREF=y
+CONFIG_IPV6_ROUTE_INFO=y
+CONFIG_IPV6_OPTIMISTIC_DAD=y
+CONFIG_INET6_AH=m
+CONFIG_INET6_ESP=m
+CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_TUNNEL=m
+CONFIG_IPV6_MROUTE=y
+CONFIG_IPV6_PIMSM_V2=y
+CONFIG_NETWORK_SECMARK=y
+CONFIG_NETFILTER=y
+CONFIG_NF_CONNTRACK=m
+CONFIG_NF_CONNTRACK_SECMARK=y
+CONFIG_NF_CONNTRACK_EVENTS=y
+CONFIG_NF_CONNTRACK_AMANDA=m
+CONFIG_NF_CONNTRACK_FTP=m
+CONFIG_NF_CONNTRACK_H323=m
+CONFIG_NF_CONNTRACK_IRC=m
+CONFIG_NF_CONNTRACK_PPTP=m
+CONFIG_NF_CONNTRACK_SANE=m
+CONFIG_NF_CONNTRACK_SIP=m
+CONFIG_NF_CONNTRACK_TFTP=m
+CONFIG_NF_CT_NETLINK=m
+CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
+CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
+CONFIG_NETFILTER_XT_TARGET_MARK=m
+CONFIG_NETFILTER_XT_TARGET_NFLOG=m
+CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_TARGET_TPROXY=m
+CONFIG_NETFILTER_XT_TARGET_TRACE=m
+CONFIG_NETFILTER_XT_TARGET_SECMARK=m
+CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
+CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP=m
+CONFIG_NETFILTER_XT_MATCH_COMMENT=m
+CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
+CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
+CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
+CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+CONFIG_NETFILTER_XT_MATCH_DCCP=m
+CONFIG_NETFILTER_XT_MATCH_ESP=m
+CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
+CONFIG_NETFILTER_XT_MATCH_HELPER=m
+CONFIG_NETFILTER_XT_MATCH_IPRANGE=m
+CONFIG_NETFILTER_XT_MATCH_LENGTH=m
+CONFIG_NETFILTER_XT_MATCH_LIMIT=m
+CONFIG_NETFILTER_XT_MATCH_MAC=m
+CONFIG_NETFILTER_XT_MATCH_MARK=m
+CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_OWNER=m
+CONFIG_NETFILTER_XT_MATCH_POLICY=m
+CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
+CONFIG_NETFILTER_XT_MATCH_QUOTA=m
+CONFIG_NETFILTER_XT_MATCH_RATEEST=m
+CONFIG_NETFILTER_XT_MATCH_REALM=m
+CONFIG_NETFILTER_XT_MATCH_RECENT=m
+CONFIG_NETFILTER_XT_MATCH_SOCKET=m
+CONFIG_NETFILTER_XT_MATCH_STATE=m
+CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
+CONFIG_NETFILTER_XT_MATCH_STRING=m
+CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
+CONFIG_NETFILTER_XT_MATCH_TIME=m
+CONFIG_NETFILTER_XT_MATCH_U32=m
+CONFIG_IP_VS=m
+CONFIG_IP_VS_IPV6=y
+CONFIG_IP_VS_PROTO_TCP=y
+CONFIG_IP_VS_PROTO_UDP=y
+CONFIG_IP_VS_PROTO_ESP=y
+CONFIG_IP_VS_PROTO_AH=y
+CONFIG_IP_VS_RR=m
+CONFIG_IP_VS_WRR=m
+CONFIG_IP_VS_LC=m
+CONFIG_IP_VS_WLC=m
+CONFIG_IP_VS_LBLC=m
+CONFIG_IP_VS_LBLCR=m
+CONFIG_IP_VS_DH=m
+CONFIG_IP_VS_SH=m
+CONFIG_IP_VS_SED=m
+CONFIG_IP_VS_NQ=m
+CONFIG_IP_NF_IPTABLES=m
+CONFIG_IP_NF_MATCH_AH=m
+CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_TTL=m
+CONFIG_IP_NF_FILTER=m
+CONFIG_IP_NF_TARGET_REJECT=m
+CONFIG_IP_NF_MANGLE=m
+CONFIG_IP_NF_TARGET_CLUSTERIP=m
+CONFIG_IP_NF_TARGET_ECN=m
+CONFIG_IP_NF_TARGET_TTL=m
+CONFIG_IP_NF_RAW=m
+CONFIG_IP_NF_ARPTABLES=m
+CONFIG_IP_NF_ARPFILTER=m
+CONFIG_IP_NF_ARP_MANGLE=m
+CONFIG_IP6_NF_MATCH_AH=m
+CONFIG_IP6_NF_MATCH_EUI64=m
+CONFIG_IP6_NF_MATCH_FRAG=m
+CONFIG_IP6_NF_MATCH_OPTS=m
+CONFIG_IP6_NF_MATCH_HL=m
+CONFIG_IP6_NF_MATCH_IPV6HEADER=m
+CONFIG_IP6_NF_MATCH_MH=m
+CONFIG_IP6_NF_MATCH_RT=m
+CONFIG_IP6_NF_TARGET_HL=m
+CONFIG_IP6_NF_FILTER=m
+CONFIG_IP6_NF_TARGET_REJECT=m
+CONFIG_IP6_NF_MANGLE=m
+CONFIG_IP6_NF_RAW=m
+CONFIG_BRIDGE_NF_EBTABLES=m
+CONFIG_BRIDGE_EBT_BROUTE=m
+CONFIG_BRIDGE_EBT_T_FILTER=m
+CONFIG_BRIDGE_EBT_T_NAT=m
+CONFIG_BRIDGE_EBT_802_3=m
+CONFIG_BRIDGE_EBT_AMONG=m
+CONFIG_BRIDGE_EBT_ARP=m
+CONFIG_BRIDGE_EBT_IP=m
+CONFIG_BRIDGE_EBT_IP6=m
+CONFIG_BRIDGE_EBT_LIMIT=m
+CONFIG_BRIDGE_EBT_MARK=m
+CONFIG_BRIDGE_EBT_PKTTYPE=m
+CONFIG_BRIDGE_EBT_STP=m
+CONFIG_BRIDGE_EBT_VLAN=m
+CONFIG_BRIDGE_EBT_ARPREPLY=m
+CONFIG_BRIDGE_EBT_DNAT=m
+CONFIG_BRIDGE_EBT_MARK_T=m
+CONFIG_BRIDGE_EBT_REDIRECT=m
+CONFIG_BRIDGE_EBT_SNAT=m
+CONFIG_BRIDGE_EBT_LOG=m
+CONFIG_BRIDGE_EBT_NFLOG=m
+CONFIG_IP_SCTP=m
+CONFIG_BRIDGE=m
+CONFIG_VLAN_8021Q=m
+CONFIG_VLAN_8021Q_GVRP=y
+CONFIG_ATALK=m
+CONFIG_DEV_APPLETALK=m
+CONFIG_IPDDP=m
+CONFIG_IPDDP_ENCAP=y
+CONFIG_PHONET=m
+CONFIG_NET_SCHED=y
+CONFIG_NET_SCH_CBQ=m
+CONFIG_NET_SCH_HTB=m
+CONFIG_NET_SCH_HFSC=m
+CONFIG_NET_SCH_PRIO=m
+CONFIG_NET_SCH_RED=m
+CONFIG_NET_SCH_SFQ=m
+CONFIG_NET_SCH_TEQL=m
+CONFIG_NET_SCH_TBF=m
+CONFIG_NET_SCH_GRED=m
+CONFIG_NET_SCH_DSMARK=m
+CONFIG_NET_SCH_NETEM=m
+CONFIG_NET_SCH_INGRESS=m
+CONFIG_NET_CLS_BASIC=m
+CONFIG_NET_CLS_TCINDEX=m
+CONFIG_NET_CLS_ROUTE4=m
+CONFIG_NET_CLS_FW=m
+CONFIG_NET_CLS_U32=m
+CONFIG_NET_CLS_RSVP=m
+CONFIG_NET_CLS_RSVP6=m
+CONFIG_NET_CLS_FLOW=m
+CONFIG_NET_CLS_ACT=y
+CONFIG_NET_ACT_POLICE=y
+CONFIG_NET_ACT_GACT=m
+CONFIG_GACT_PROB=y
+CONFIG_NET_ACT_MIRRED=m
+CONFIG_NET_ACT_IPT=m
+CONFIG_NET_ACT_NAT=m
+CONFIG_NET_ACT_PEDIT=m
+CONFIG_NET_ACT_SIMP=m
+CONFIG_NET_ACT_SKBEDIT=m
+CONFIG_CFG80211=m
+CONFIG_MAC80211=m
+CONFIG_MAC80211_MESH=y
+CONFIG_RFKILL=m
+CONFIG_DEVTMPFS=y
+CONFIG_CONNECTOR=m
+CONFIG_MTD=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_OOPS=m
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_CFI_STAA=y
+CONFIG_MTD_PHYSMAP_OF=y
+CONFIG_MTD_UBI=m
+CONFIG_MTD_UBI_GLUEBI=m
+CONFIG_BLK_DEV_FD=m
+CONFIG_BLK_DEV_LOOP=m
+CONFIG_BLK_DEV_NBD=m
+CONFIG_BLK_DEV_RAM=y
+CONFIG_CDROM_PKTCDVD=m
+CONFIG_ATA_OVER_ETH=m
+CONFIG_RAID_ATTRS=m
+CONFIG_BLK_DEV_SD=y
+CONFIG_CHR_DEV_ST=m
+CONFIG_BLK_DEV_SR=y
+CONFIG_CHR_DEV_SG=m
+CONFIG_SCSI_CONSTANTS=y
+CONFIG_SCSI_LOGGING=y
+CONFIG_SCSI_SCAN_ASYNC=y
+CONFIG_SCSI_FC_ATTRS=m
+CONFIG_ISCSI_TCP=m
+CONFIG_BLK_DEV_3W_XXXX_RAID=m
+CONFIG_SCSI_3W_9XXX=m
+CONFIG_SCSI_ACARD=m
+CONFIG_SCSI_AACRAID=m
+CONFIG_SCSI_AIC7XXX=m
+CONFIG_AIC7XXX_RESET_DELAY_MS=15000
+# CONFIG_AIC7XXX_DEBUG_ENABLE is not set
+CONFIG_ATA=y
+CONFIG_ATA_PIIX=y
+CONFIG_PATA_IT8213=m
+CONFIG_PATA_OLDPIIX=y
+CONFIG_PATA_MPIIX=y
+CONFIG_ATA_GENERIC=y
+CONFIG_PATA_LEGACY=y
+CONFIG_MD=y
+CONFIG_BLK_DEV_MD=m
+CONFIG_MD_LINEAR=m
+CONFIG_MD_RAID0=m
+CONFIG_MD_RAID1=m
+CONFIG_MD_RAID10=m
+CONFIG_MD_RAID456=m
+CONFIG_MD_MULTIPATH=m
+CONFIG_MD_FAULTY=m
+CONFIG_BLK_DEV_DM=m
+CONFIG_DM_CRYPT=m
+CONFIG_DM_SNAPSHOT=m
+CONFIG_DM_MIRROR=m
+CONFIG_DM_ZERO=m
+CONFIG_DM_MULTIPATH=m
+CONFIG_NETDEVICES=y
+CONFIG_BONDING=m
+CONFIG_DUMMY=m
+CONFIG_EQUALIZER=m
+CONFIG_IFB=m
+CONFIG_MACVLAN=m
+CONFIG_TUN=m
+CONFIG_VETH=m
+CONFIG_PCNET32=y
+CONFIG_CHELSIO_T3=m
+CONFIG_AX88796=m
+CONFIG_NETXEN_NIC=m
+CONFIG_TC35815=m
+CONFIG_BROADCOM_PHY=m
+CONFIG_CICADA_PHY=m
+CONFIG_DAVICOM_PHY=m
+CONFIG_ICPLUS_PHY=m
+CONFIG_LXT_PHY=m
+CONFIG_MARVELL_PHY=m
+CONFIG_QSEMI_PHY=m
+CONFIG_REALTEK_PHY=m
+CONFIG_SMSC_PHY=m
+CONFIG_VITESSE_PHY=m
+CONFIG_ATMEL=m
+CONFIG_PCI_ATMEL=m
+CONFIG_IPW2100=m
+CONFIG_IPW2100_MONITOR=y
+CONFIG_HOSTAP=m
+CONFIG_HOSTAP_FIRMWARE=y
+CONFIG_HOSTAP_FIRMWARE_NVRAM=y
+CONFIG_HOSTAP_PLX=m
+CONFIG_HOSTAP_PCI=m
+CONFIG_LIBERTAS=m
+CONFIG_INPUT_MOUSEDEV=y
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_POWER_RESET=y
+CONFIG_POWER_RESET_PIIX4_POWEROFF=y
+CONFIG_POWER_RESET_SYSCON=y
+# CONFIG_HWMON is not set
+CONFIG_FB=y
+CONFIG_FB_CIRRUS=y
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_HID=m
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_CMOS=y
+CONFIG_UIO=m
+CONFIG_UIO_CIF=m
+CONFIG_EXT2_FS=y
+CONFIG_EXT3_FS=y
+CONFIG_REISERFS_FS=m
+CONFIG_REISERFS_PROC_INFO=y
+CONFIG_REISERFS_FS_XATTR=y
+CONFIG_REISERFS_FS_POSIX_ACL=y
+CONFIG_REISERFS_FS_SECURITY=y
+CONFIG_JFS_FS=m
+CONFIG_JFS_POSIX_ACL=y
+CONFIG_JFS_SECURITY=y
+CONFIG_XFS_FS=m
+CONFIG_XFS_QUOTA=y
+CONFIG_XFS_POSIX_ACL=y
+CONFIG_QUOTA=y
+CONFIG_QFMT_V2=y
+CONFIG_FUSE_FS=m
+CONFIG_ISO9660_FS=m
+CONFIG_JOLIET=y
+CONFIG_ZISOFS=y
+CONFIG_UDF_FS=m
+CONFIG_MSDOS_FS=m
+CONFIG_VFAT_FS=m
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_AFFS_FS=m
+CONFIG_HFS_FS=m
+CONFIG_HFSPLUS_FS=m
+CONFIG_BEFS_FS=m
+CONFIG_BFS_FS=m
+CONFIG_EFS_FS=m
+CONFIG_JFFS2_FS=m
+CONFIG_JFFS2_FS_XATTR=y
+CONFIG_JFFS2_COMPRESSION_OPTIONS=y
+CONFIG_JFFS2_RUBIN=y
+CONFIG_CRAMFS=m
+CONFIG_VXFS_FS=m
+CONFIG_MINIX_FS=m
+CONFIG_ROMFS_FS=m
+CONFIG_SYSV_FS=m
+CONFIG_UFS_FS=m
+CONFIG_NFS_FS=y
+CONFIG_ROOT_NFS=y
+CONFIG_NFSD=y
+CONFIG_NLS_CODEPAGE_437=m
+CONFIG_NLS_CODEPAGE_737=m
+CONFIG_NLS_CODEPAGE_775=m
+CONFIG_NLS_CODEPAGE_850=m
+CONFIG_NLS_CODEPAGE_852=m
+CONFIG_NLS_CODEPAGE_855=m
+CONFIG_NLS_CODEPAGE_857=m
+CONFIG_NLS_CODEPAGE_860=m
+CONFIG_NLS_CODEPAGE_861=m
+CONFIG_NLS_CODEPAGE_862=m
+CONFIG_NLS_CODEPAGE_863=m
+CONFIG_NLS_CODEPAGE_864=m
+CONFIG_NLS_CODEPAGE_865=m
+CONFIG_NLS_CODEPAGE_866=m
+CONFIG_NLS_CODEPAGE_869=m
+CONFIG_NLS_CODEPAGE_936=m
+CONFIG_NLS_CODEPAGE_950=m
+CONFIG_NLS_CODEPAGE_932=m
+CONFIG_NLS_CODEPAGE_949=m
+CONFIG_NLS_CODEPAGE_874=m
+CONFIG_NLS_ISO8859_8=m
+CONFIG_NLS_CODEPAGE_1250=m
+CONFIG_NLS_CODEPAGE_1251=m
+CONFIG_NLS_ASCII=m
+CONFIG_NLS_ISO8859_1=m
+CONFIG_NLS_ISO8859_2=m
+CONFIG_NLS_ISO8859_3=m
+CONFIG_NLS_ISO8859_4=m
+CONFIG_NLS_ISO8859_5=m
+CONFIG_NLS_ISO8859_6=m
+CONFIG_NLS_ISO8859_7=m
+CONFIG_NLS_ISO8859_9=m
+CONFIG_NLS_ISO8859_13=m
+CONFIG_NLS_ISO8859_14=m
+CONFIG_NLS_ISO8859_15=m
+CONFIG_NLS_KOI8_R=m
+CONFIG_NLS_KOI8_U=m
+CONFIG_CRYPTO_CRYPTD=m
+CONFIG_CRYPTO_LRW=m
+CONFIG_CRYPTO_PCBC=m
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_XCBC=m
+CONFIG_CRYPTO_MD4=m
+CONFIG_CRYPTO_SHA512=m
+CONFIG_CRYPTO_WP512=m
+CONFIG_CRYPTO_ANUBIS=m
+CONFIG_CRYPTO_BLOWFISH=m
+CONFIG_CRYPTO_CAMELLIA=m
+CONFIG_CRYPTO_CAST5=m
+CONFIG_CRYPTO_CAST6=m
+CONFIG_CRYPTO_FCRYPT=m
+CONFIG_CRYPTO_KHAZAD=m
+CONFIG_CRYPTO_SERPENT=m
+CONFIG_CRYPTO_TEA=m
+CONFIG_CRYPTO_TWOFISH=m
+CONFIG_RCU_CPU_STALL_TIMEOUT=60
+CONFIG_ENABLE_DEFAULT_TRACERS=y
diff --git a/arch/mips/configs/malta_qemu_32r6_defconfig b/arch/mips/configs/malta_qemu_32r6_defconfig
new file mode 100644
index 000000000..fd63a2b15
--- /dev/null
+++ b/arch/mips/configs/malta_qemu_32r6_defconfig
@@ -0,0 +1,183 @@
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_AUDIT=y
+CONFIG_NO_HZ=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=15
+CONFIG_EMBEDDED=y
+CONFIG_SLAB=y
+CONFIG_MIPS_MALTA=y
+CONFIG_CPU_LITTLE_ENDIAN=y
+CONFIG_CPU_MIPS32_R6=y
+CONFIG_PAGE_SIZE_16KB=y
+CONFIG_HZ_100=y
+CONFIG_PCI=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_XFRM_USER=m
+CONFIG_NET_KEY=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_MULTIPLE_TABLES=y
+CONFIG_IP_ROUTE_MULTIPATH=y
+CONFIG_IP_ROUTE_VERBOSE=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_NET_IPIP=m
+CONFIG_IP_MROUTE=y
+CONFIG_IP_PIMSM_V1=y
+CONFIG_IP_PIMSM_V2=y
+CONFIG_SYN_COOKIES=y
+CONFIG_INET_AH=m
+CONFIG_INET_ESP=m
+CONFIG_INET_IPCOMP=m
+CONFIG_INET6_AH=m
+CONFIG_INET6_ESP=m
+CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_TUNNEL=m
+CONFIG_BRIDGE=m
+CONFIG_VLAN_8021Q=m
+CONFIG_ATALK=m
+CONFIG_DEV_APPLETALK=m
+CONFIG_IPDDP=m
+CONFIG_IPDDP_ENCAP=y
+CONFIG_NET_SCHED=y
+CONFIG_NET_SCH_CBQ=m
+CONFIG_NET_SCH_HTB=m
+CONFIG_NET_SCH_HFSC=m
+CONFIG_NET_SCH_PRIO=m
+CONFIG_NET_SCH_RED=m
+CONFIG_NET_SCH_SFQ=m
+CONFIG_NET_SCH_TEQL=m
+CONFIG_NET_SCH_TBF=m
+CONFIG_NET_SCH_GRED=m
+CONFIG_NET_SCH_DSMARK=m
+CONFIG_NET_SCH_NETEM=m
+CONFIG_NET_SCH_INGRESS=m
+CONFIG_NET_CLS_BASIC=m
+CONFIG_NET_CLS_TCINDEX=m
+CONFIG_NET_CLS_ROUTE4=m
+CONFIG_NET_CLS_FW=m
+CONFIG_NET_CLS_U32=m
+CONFIG_NET_CLS_RSVP=m
+CONFIG_NET_CLS_RSVP6=m
+CONFIG_NET_CLS_ACT=y
+CONFIG_NET_ACT_POLICE=y
+# CONFIG_WIRELESS is not set
+CONFIG_DEVTMPFS=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_CHR_DEV_SG=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_ATA=y
+CONFIG_ATA_PIIX=y
+CONFIG_PATA_OLDPIIX=y
+CONFIG_PATA_MPIIX=y
+CONFIG_ATA_GENERIC=y
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_3COM is not set
+# CONFIG_NET_VENDOR_ADAPTEC is not set
+# CONFIG_NET_VENDOR_ALTEON is not set
+CONFIG_PCNET32=y
+# CONFIG_NET_VENDOR_ATHEROS is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_BROCADE is not set
+# CONFIG_NET_VENDOR_CHELSIO is not set
+# CONFIG_NET_VENDOR_CISCO is not set
+# CONFIG_NET_VENDOR_DEC is not set
+# CONFIG_NET_VENDOR_DLINK is not set
+# CONFIG_NET_VENDOR_EMULEX is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MELLANOX is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_MYRI is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_NVIDIA is not set
+# CONFIG_NET_VENDOR_OKI is not set
+# CONFIG_NET_VENDOR_QLOGIC is not set
+# CONFIG_NET_VENDOR_RDC is not set
+# CONFIG_NET_VENDOR_REALTEK is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SILAN is not set
+# CONFIG_NET_VENDOR_SIS is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_SUN is not set
+# CONFIG_NET_VENDOR_TEHUTI is not set
+# CONFIG_NET_VENDOR_TI is not set
+# CONFIG_NET_VENDOR_TOSHIBA is not set
+# CONFIG_NET_VENDOR_VIA is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+# CONFIG_WLAN is not set
+CONFIG_INPUT_MOUSEDEV=y
+# CONFIG_VT is not set
+CONFIG_LEGACY_PTY_COUNT=4
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_HW_RANDOM=y
+CONFIG_POWER_RESET=y
+CONFIG_POWER_RESET_PIIX4_POWEROFF=y
+CONFIG_POWER_RESET_SYSCON=y
+# CONFIG_HWMON is not set
+CONFIG_FB=y
+CONFIG_FIRMWARE_EDID=y
+CONFIG_FB_MATROX=y
+CONFIG_FB_MATROX_G=y
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+CONFIG_USB_UHCI_HCD=y
+CONFIG_USB_STORAGE=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_DISK=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_BACKLIGHT=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_CMOS=y
+CONFIG_EXT2_FS=y
+CONFIG_EXT3_FS=y
+CONFIG_XFS_FS=y
+CONFIG_XFS_QUOTA=y
+CONFIG_XFS_POSIX_ACL=y
+CONFIG_QUOTA=y
+CONFIG_QFMT_V2=y
+CONFIG_MSDOS_FS=m
+CONFIG_VFAT_FS=m
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_NFS_FS=y
+CONFIG_ROOT_NFS=y
+CONFIG_CIFS=m
+CONFIG_CIFS_XATTR=y
+CONFIG_CIFS_POSIX=y
+CONFIG_NLS_CODEPAGE_437=m
+CONFIG_NLS_ISO8859_1=m
+CONFIG_CRYPTO_PCBC=m
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_WP512=m
+CONFIG_CRYPTO_ANUBIS=m
+CONFIG_CRYPTO_BLOWFISH=m
+CONFIG_CRYPTO_CAST5=m
+CONFIG_CRYPTO_CAST6=m
+CONFIG_CRYPTO_KHAZAD=m
+CONFIG_CRYPTO_SERPENT=m
+CONFIG_CRYPTO_TEA=m
+CONFIG_CRYPTO_TWOFISH=m
+# CONFIG_CRYPTO_HW is not set
+# CONFIG_FTRACE is not set
diff --git a/arch/mips/configs/maltaaprp_defconfig b/arch/mips/configs/maltaaprp_defconfig
new file mode 100644
index 000000000..1f07e354c
--- /dev/null
+++ b/arch/mips/configs/maltaaprp_defconfig
@@ -0,0 +1,184 @@
+CONFIG_LOCALVERSION="aprp"
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_AUDIT=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=15
+CONFIG_EMBEDDED=y
+CONFIG_SLAB=y
+CONFIG_MIPS_MALTA=y
+CONFIG_CPU_LITTLE_ENDIAN=y
+CONFIG_CPU_MIPS32_R2=y
+CONFIG_MIPS_VPE_LOADER=y
+CONFIG_MIPS_VPE_APSP_API=y
+CONFIG_NR_CPUS=2
+CONFIG_HZ_100=y
+CONFIG_PCI=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_XFRM_USER=m
+CONFIG_NET_KEY=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_MULTIPLE_TABLES=y
+CONFIG_IP_ROUTE_MULTIPATH=y
+CONFIG_IP_ROUTE_VERBOSE=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_NET_IPIP=m
+CONFIG_IP_MROUTE=y
+CONFIG_IP_PIMSM_V1=y
+CONFIG_IP_PIMSM_V2=y
+CONFIG_SYN_COOKIES=y
+CONFIG_INET_AH=m
+CONFIG_INET_ESP=m
+CONFIG_INET_IPCOMP=m
+CONFIG_INET6_AH=m
+CONFIG_INET6_ESP=m
+CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_TUNNEL=m
+CONFIG_BRIDGE=m
+CONFIG_VLAN_8021Q=m
+CONFIG_ATALK=m
+CONFIG_DEV_APPLETALK=m
+CONFIG_IPDDP=m
+CONFIG_IPDDP_ENCAP=y
+CONFIG_NET_SCHED=y
+CONFIG_NET_SCH_CBQ=m
+CONFIG_NET_SCH_HTB=m
+CONFIG_NET_SCH_HFSC=m
+CONFIG_NET_SCH_PRIO=m
+CONFIG_NET_SCH_RED=m
+CONFIG_NET_SCH_SFQ=m
+CONFIG_NET_SCH_TEQL=m
+CONFIG_NET_SCH_TBF=m
+CONFIG_NET_SCH_GRED=m
+CONFIG_NET_SCH_DSMARK=m
+CONFIG_NET_SCH_NETEM=m
+CONFIG_NET_SCH_INGRESS=m
+CONFIG_NET_CLS_BASIC=m
+CONFIG_NET_CLS_TCINDEX=m
+CONFIG_NET_CLS_ROUTE4=m
+CONFIG_NET_CLS_FW=m
+CONFIG_NET_CLS_U32=m
+CONFIG_NET_CLS_RSVP=m
+CONFIG_NET_CLS_RSVP6=m
+CONFIG_NET_CLS_ACT=y
+CONFIG_NET_ACT_POLICE=y
+# CONFIG_WIRELESS is not set
+CONFIG_DEVTMPFS=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_CHR_DEV_SG=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_ATA=y
+CONFIG_ATA_PIIX=y
+CONFIG_PATA_OLDPIIX=y
+CONFIG_PATA_MPIIX=y
+CONFIG_ATA_GENERIC=y
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_3COM is not set
+# CONFIG_NET_VENDOR_ADAPTEC is not set
+# CONFIG_NET_VENDOR_ALTEON is not set
+CONFIG_PCNET32=y
+# CONFIG_NET_VENDOR_ATHEROS is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_BROCADE is not set
+# CONFIG_NET_VENDOR_CHELSIO is not set
+# CONFIG_NET_VENDOR_CISCO is not set
+# CONFIG_NET_VENDOR_DEC is not set
+# CONFIG_NET_VENDOR_DLINK is not set
+# CONFIG_NET_VENDOR_EMULEX is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MELLANOX is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_MYRI is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_NVIDIA is not set
+# CONFIG_NET_VENDOR_OKI is not set
+# CONFIG_NET_VENDOR_QLOGIC is not set
+# CONFIG_NET_VENDOR_RDC is not set
+# CONFIG_NET_VENDOR_REALTEK is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SILAN is not set
+# CONFIG_NET_VENDOR_SIS is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_SUN is not set
+# CONFIG_NET_VENDOR_TEHUTI is not set
+# CONFIG_NET_VENDOR_TI is not set
+# CONFIG_NET_VENDOR_TOSHIBA is not set
+# CONFIG_NET_VENDOR_VIA is not set
+# CONFIG_WLAN is not set
+CONFIG_INPUT_MOUSEDEV=y
+# CONFIG_VT is not set
+CONFIG_LEGACY_PTY_COUNT=16
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_HW_RANDOM=y
+CONFIG_POWER_RESET=y
+CONFIG_POWER_RESET_PIIX4_POWEROFF=y
+CONFIG_POWER_RESET_SYSCON=y
+# CONFIG_HWMON is not set
+CONFIG_FB=y
+CONFIG_FIRMWARE_EDID=y
+CONFIG_FB_MATROX=y
+CONFIG_FB_MATROX_G=y
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+CONFIG_USB_UHCI_HCD=y
+CONFIG_USB_STORAGE=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_DISK=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_BACKLIGHT=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_CMOS=y
+CONFIG_EXT2_FS=y
+CONFIG_EXT3_FS=y
+CONFIG_XFS_FS=y
+CONFIG_XFS_QUOTA=y
+CONFIG_XFS_POSIX_ACL=y
+CONFIG_QUOTA=y
+CONFIG_QFMT_V2=y
+CONFIG_MSDOS_FS=m
+CONFIG_VFAT_FS=m
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_NFS_FS=y
+CONFIG_ROOT_NFS=y
+CONFIG_CIFS=m
+CONFIG_CIFS_XATTR=y
+CONFIG_CIFS_POSIX=y
+CONFIG_NLS_CODEPAGE_437=m
+CONFIG_NLS_ISO8859_1=m
+CONFIG_CRYPTO_PCBC=m
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_WP512=m
+CONFIG_CRYPTO_ANUBIS=m
+CONFIG_CRYPTO_BLOWFISH=m
+CONFIG_CRYPTO_CAST5=m
+CONFIG_CRYPTO_CAST6=m
+CONFIG_CRYPTO_KHAZAD=m
+CONFIG_CRYPTO_SERPENT=m
+CONFIG_CRYPTO_TEA=m
+CONFIG_CRYPTO_TWOFISH=m
+# CONFIG_CRYPTO_HW is not set
+# CONFIG_FTRACE is not set
diff --git a/arch/mips/configs/maltasmvp_defconfig b/arch/mips/configs/maltasmvp_defconfig
new file mode 100644
index 000000000..5cd3eca23
--- /dev/null
+++ b/arch/mips/configs/maltasmvp_defconfig
@@ -0,0 +1,185 @@
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_AUDIT=y
+CONFIG_NO_HZ=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=15
+CONFIG_EMBEDDED=y
+CONFIG_SLAB=y
+CONFIG_MIPS_MALTA=y
+CONFIG_CPU_LITTLE_ENDIAN=y
+CONFIG_CPU_MIPS32_R2=y
+CONFIG_PAGE_SIZE_16KB=y
+CONFIG_SCHED_SMT=y
+CONFIG_MIPS_CPS=y
+CONFIG_NR_CPUS=8
+CONFIG_HZ_100=y
+CONFIG_PCI=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_XFRM_USER=m
+CONFIG_NET_KEY=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_MULTIPLE_TABLES=y
+CONFIG_IP_ROUTE_MULTIPATH=y
+CONFIG_IP_ROUTE_VERBOSE=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_NET_IPIP=m
+CONFIG_IP_MROUTE=y
+CONFIG_IP_PIMSM_V1=y
+CONFIG_IP_PIMSM_V2=y
+CONFIG_SYN_COOKIES=y
+CONFIG_INET_AH=m
+CONFIG_INET_ESP=m
+CONFIG_INET_IPCOMP=m
+CONFIG_INET6_AH=m
+CONFIG_INET6_ESP=m
+CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_TUNNEL=m
+CONFIG_BRIDGE=m
+CONFIG_VLAN_8021Q=m
+CONFIG_ATALK=m
+CONFIG_DEV_APPLETALK=m
+CONFIG_IPDDP=m
+CONFIG_IPDDP_ENCAP=y
+CONFIG_NET_SCHED=y
+CONFIG_NET_SCH_CBQ=m
+CONFIG_NET_SCH_HTB=m
+CONFIG_NET_SCH_HFSC=m
+CONFIG_NET_SCH_PRIO=m
+CONFIG_NET_SCH_RED=m
+CONFIG_NET_SCH_SFQ=m
+CONFIG_NET_SCH_TEQL=m
+CONFIG_NET_SCH_TBF=m
+CONFIG_NET_SCH_GRED=m
+CONFIG_NET_SCH_DSMARK=m
+CONFIG_NET_SCH_NETEM=m
+CONFIG_NET_SCH_INGRESS=m
+CONFIG_NET_CLS_BASIC=m
+CONFIG_NET_CLS_TCINDEX=m
+CONFIG_NET_CLS_ROUTE4=m
+CONFIG_NET_CLS_FW=m
+CONFIG_NET_CLS_U32=m
+CONFIG_NET_CLS_RSVP=m
+CONFIG_NET_CLS_RSVP6=m
+CONFIG_NET_CLS_ACT=y
+CONFIG_NET_ACT_POLICE=y
+# CONFIG_WIRELESS is not set
+CONFIG_DEVTMPFS=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_CHR_DEV_SG=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_ATA=y
+# CONFIG_SATA_PMP is not set
+CONFIG_ATA_PIIX=y
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_3COM is not set
+# CONFIG_NET_VENDOR_ADAPTEC is not set
+# CONFIG_NET_VENDOR_ALTEON is not set
+CONFIG_PCNET32=y
+# CONFIG_NET_VENDOR_ATHEROS is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_BROCADE is not set
+# CONFIG_NET_VENDOR_CHELSIO is not set
+# CONFIG_NET_VENDOR_CISCO is not set
+# CONFIG_NET_VENDOR_DEC is not set
+# CONFIG_NET_VENDOR_DLINK is not set
+# CONFIG_NET_VENDOR_EMULEX is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MELLANOX is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_MYRI is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_NVIDIA is not set
+# CONFIG_NET_VENDOR_OKI is not set
+# CONFIG_NET_VENDOR_QLOGIC is not set
+# CONFIG_NET_VENDOR_RDC is not set
+# CONFIG_NET_VENDOR_REALTEK is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SILAN is not set
+# CONFIG_NET_VENDOR_SIS is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_SUN is not set
+# CONFIG_NET_VENDOR_TEHUTI is not set
+# CONFIG_NET_VENDOR_TI is not set
+# CONFIG_NET_VENDOR_TOSHIBA is not set
+# CONFIG_NET_VENDOR_VIA is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+# CONFIG_WLAN is not set
+CONFIG_INPUT_MOUSEDEV=y
+# CONFIG_VT is not set
+CONFIG_LEGACY_PTY_COUNT=4
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_HW_RANDOM=y
+CONFIG_POWER_RESET=y
+CONFIG_POWER_RESET_PIIX4_POWEROFF=y
+CONFIG_POWER_RESET_SYSCON=y
+# CONFIG_HWMON is not set
+CONFIG_FB=y
+CONFIG_FIRMWARE_EDID=y
+CONFIG_FB_MATROX=y
+CONFIG_FB_MATROX_G=y
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+CONFIG_USB_UHCI_HCD=y
+CONFIG_USB_STORAGE=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_BACKLIGHT=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_CMOS=y
+CONFIG_EXT2_FS=y
+CONFIG_EXT3_FS=y
+CONFIG_EXT3_FS_POSIX_ACL=y
+CONFIG_EXT3_FS_SECURITY=y
+CONFIG_XFS_FS=y
+CONFIG_XFS_QUOTA=y
+CONFIG_XFS_POSIX_ACL=y
+CONFIG_QUOTA=y
+CONFIG_QFMT_V2=y
+CONFIG_MSDOS_FS=m
+CONFIG_VFAT_FS=m
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_NFS_FS=y
+CONFIG_ROOT_NFS=y
+CONFIG_CIFS=m
+CONFIG_CIFS_XATTR=y
+CONFIG_CIFS_POSIX=y
+CONFIG_NLS_CODEPAGE_437=m
+CONFIG_NLS_ISO8859_1=m
+CONFIG_CRYPTO_PCBC=m
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_WP512=m
+CONFIG_CRYPTO_ANUBIS=m
+CONFIG_CRYPTO_BLOWFISH=m
+CONFIG_CRYPTO_CAST5=m
+CONFIG_CRYPTO_CAST6=m
+CONFIG_CRYPTO_KHAZAD=m
+CONFIG_CRYPTO_SERPENT=m
+CONFIG_CRYPTO_TEA=m
+CONFIG_CRYPTO_TWOFISH=m
+# CONFIG_CRYPTO_HW is not set
+# CONFIG_FTRACE is not set
diff --git a/arch/mips/configs/maltasmvp_eva_defconfig b/arch/mips/configs/maltasmvp_eva_defconfig
new file mode 100644
index 000000000..45688e742
--- /dev/null
+++ b/arch/mips/configs/maltasmvp_eva_defconfig
@@ -0,0 +1,187 @@
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_AUDIT=y
+CONFIG_NO_HZ=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=15
+CONFIG_EMBEDDED=y
+CONFIG_SLAB=y
+CONFIG_MIPS_MALTA=y
+CONFIG_CPU_LITTLE_ENDIAN=y
+CONFIG_CPU_MIPS32_R2=y
+CONFIG_CPU_MIPS32_3_5_FEATURES=y
+CONFIG_PAGE_SIZE_16KB=y
+CONFIG_SCHED_SMT=y
+CONFIG_MIPS_CPS=y
+CONFIG_NR_CPUS=8
+CONFIG_HZ_100=y
+CONFIG_PCI=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_XFRM_USER=m
+CONFIG_NET_KEY=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_MULTIPLE_TABLES=y
+CONFIG_IP_ROUTE_MULTIPATH=y
+CONFIG_IP_ROUTE_VERBOSE=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_NET_IPIP=m
+CONFIG_IP_MROUTE=y
+CONFIG_IP_PIMSM_V1=y
+CONFIG_IP_PIMSM_V2=y
+CONFIG_SYN_COOKIES=y
+CONFIG_INET_AH=m
+CONFIG_INET_ESP=m
+CONFIG_INET_IPCOMP=m
+CONFIG_INET6_AH=m
+CONFIG_INET6_ESP=m
+CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_TUNNEL=m
+CONFIG_BRIDGE=m
+CONFIG_VLAN_8021Q=m
+CONFIG_ATALK=m
+CONFIG_DEV_APPLETALK=m
+CONFIG_IPDDP=m
+CONFIG_IPDDP_ENCAP=y
+CONFIG_NET_SCHED=y
+CONFIG_NET_SCH_CBQ=m
+CONFIG_NET_SCH_HTB=m
+CONFIG_NET_SCH_HFSC=m
+CONFIG_NET_SCH_PRIO=m
+CONFIG_NET_SCH_RED=m
+CONFIG_NET_SCH_SFQ=m
+CONFIG_NET_SCH_TEQL=m
+CONFIG_NET_SCH_TBF=m
+CONFIG_NET_SCH_GRED=m
+CONFIG_NET_SCH_DSMARK=m
+CONFIG_NET_SCH_NETEM=m
+CONFIG_NET_SCH_INGRESS=m
+CONFIG_NET_CLS_BASIC=m
+CONFIG_NET_CLS_TCINDEX=m
+CONFIG_NET_CLS_ROUTE4=m
+CONFIG_NET_CLS_FW=m
+CONFIG_NET_CLS_U32=m
+CONFIG_NET_CLS_RSVP=m
+CONFIG_NET_CLS_RSVP6=m
+CONFIG_NET_CLS_ACT=y
+CONFIG_NET_ACT_POLICE=y
+# CONFIG_WIRELESS is not set
+CONFIG_DEVTMPFS=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_CHR_DEV_SG=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_ATA=y
+CONFIG_ATA_PIIX=y
+CONFIG_PATA_OLDPIIX=y
+CONFIG_PATA_MPIIX=y
+CONFIG_ATA_GENERIC=y
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_3COM is not set
+# CONFIG_NET_VENDOR_ADAPTEC is not set
+# CONFIG_NET_VENDOR_ALTEON is not set
+CONFIG_PCNET32=y
+# CONFIG_NET_VENDOR_ATHEROS is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_BROCADE is not set
+# CONFIG_NET_VENDOR_CHELSIO is not set
+# CONFIG_NET_VENDOR_CISCO is not set
+# CONFIG_NET_VENDOR_DEC is not set
+# CONFIG_NET_VENDOR_DLINK is not set
+# CONFIG_NET_VENDOR_EMULEX is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MELLANOX is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_MYRI is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_NVIDIA is not set
+# CONFIG_NET_VENDOR_OKI is not set
+# CONFIG_NET_VENDOR_QLOGIC is not set
+# CONFIG_NET_VENDOR_RDC is not set
+# CONFIG_NET_VENDOR_REALTEK is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SILAN is not set
+# CONFIG_NET_VENDOR_SIS is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_SUN is not set
+# CONFIG_NET_VENDOR_TEHUTI is not set
+# CONFIG_NET_VENDOR_TI is not set
+# CONFIG_NET_VENDOR_TOSHIBA is not set
+# CONFIG_NET_VENDOR_VIA is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+# CONFIG_WLAN is not set
+CONFIG_INPUT_MOUSEDEV=y
+# CONFIG_VT is not set
+CONFIG_LEGACY_PTY_COUNT=4
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_HW_RANDOM=y
+CONFIG_POWER_RESET=y
+CONFIG_POWER_RESET_PIIX4_POWEROFF=y
+CONFIG_POWER_RESET_SYSCON=y
+# CONFIG_HWMON is not set
+CONFIG_FB=y
+CONFIG_FIRMWARE_EDID=y
+CONFIG_FB_MATROX=y
+CONFIG_FB_MATROX_G=y
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+CONFIG_USB_UHCI_HCD=y
+CONFIG_USB_STORAGE=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_DISK=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_BACKLIGHT=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_CMOS=y
+CONFIG_EXT2_FS=y
+CONFIG_EXT3_FS=y
+CONFIG_XFS_FS=y
+CONFIG_XFS_QUOTA=y
+CONFIG_XFS_POSIX_ACL=y
+CONFIG_QUOTA=y
+CONFIG_QFMT_V2=y
+CONFIG_MSDOS_FS=m
+CONFIG_VFAT_FS=m
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_NFS_FS=y
+CONFIG_ROOT_NFS=y
+CONFIG_CIFS=m
+CONFIG_CIFS_XATTR=y
+CONFIG_CIFS_POSIX=y
+CONFIG_NLS_CODEPAGE_437=m
+CONFIG_NLS_ISO8859_1=m
+CONFIG_CRYPTO_PCBC=m
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_WP512=m
+CONFIG_CRYPTO_ANUBIS=m
+CONFIG_CRYPTO_BLOWFISH=m
+CONFIG_CRYPTO_CAST5=m
+CONFIG_CRYPTO_CAST6=m
+CONFIG_CRYPTO_KHAZAD=m
+CONFIG_CRYPTO_SERPENT=m
+CONFIG_CRYPTO_TEA=m
+CONFIG_CRYPTO_TWOFISH=m
+# CONFIG_CRYPTO_HW is not set
+# CONFIG_FTRACE is not set
diff --git a/arch/mips/configs/maltaup_defconfig b/arch/mips/configs/maltaup_defconfig
new file mode 100644
index 000000000..136f96578
--- /dev/null
+++ b/arch/mips/configs/maltaup_defconfig
@@ -0,0 +1,183 @@
+CONFIG_LOCALVERSION="up"
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_AUDIT=y
+CONFIG_NO_HZ=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=15
+CONFIG_EMBEDDED=y
+CONFIG_SLAB=y
+CONFIG_MIPS_MALTA=y
+CONFIG_CPU_LITTLE_ENDIAN=y
+CONFIG_CPU_MIPS32_R2=y
+CONFIG_NR_CPUS=2
+CONFIG_HZ_100=y
+CONFIG_PCI=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_XFRM_USER=m
+CONFIG_NET_KEY=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_MULTIPLE_TABLES=y
+CONFIG_IP_ROUTE_MULTIPATH=y
+CONFIG_IP_ROUTE_VERBOSE=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_NET_IPIP=m
+CONFIG_IP_MROUTE=y
+CONFIG_IP_PIMSM_V1=y
+CONFIG_IP_PIMSM_V2=y
+CONFIG_SYN_COOKIES=y
+CONFIG_INET_AH=m
+CONFIG_INET_ESP=m
+CONFIG_INET_IPCOMP=m
+CONFIG_INET6_AH=m
+CONFIG_INET6_ESP=m
+CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_TUNNEL=m
+CONFIG_BRIDGE=m
+CONFIG_VLAN_8021Q=m
+CONFIG_ATALK=m
+CONFIG_DEV_APPLETALK=m
+CONFIG_IPDDP=m
+CONFIG_IPDDP_ENCAP=y
+CONFIG_NET_SCHED=y
+CONFIG_NET_SCH_CBQ=m
+CONFIG_NET_SCH_HTB=m
+CONFIG_NET_SCH_HFSC=m
+CONFIG_NET_SCH_PRIO=m
+CONFIG_NET_SCH_RED=m
+CONFIG_NET_SCH_SFQ=m
+CONFIG_NET_SCH_TEQL=m
+CONFIG_NET_SCH_TBF=m
+CONFIG_NET_SCH_GRED=m
+CONFIG_NET_SCH_DSMARK=m
+CONFIG_NET_SCH_NETEM=m
+CONFIG_NET_SCH_INGRESS=m
+CONFIG_NET_CLS_BASIC=m
+CONFIG_NET_CLS_TCINDEX=m
+CONFIG_NET_CLS_ROUTE4=m
+CONFIG_NET_CLS_FW=m
+CONFIG_NET_CLS_U32=m
+CONFIG_NET_CLS_RSVP=m
+CONFIG_NET_CLS_RSVP6=m
+CONFIG_NET_CLS_ACT=y
+CONFIG_NET_ACT_POLICE=y
+# CONFIG_WIRELESS is not set
+CONFIG_DEVTMPFS=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_CHR_DEV_SG=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_ATA=y
+CONFIG_ATA_PIIX=y
+CONFIG_PATA_OLDPIIX=y
+CONFIG_PATA_MPIIX=y
+CONFIG_ATA_GENERIC=y
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_3COM is not set
+# CONFIG_NET_VENDOR_ADAPTEC is not set
+# CONFIG_NET_VENDOR_ALTEON is not set
+CONFIG_PCNET32=y
+# CONFIG_NET_VENDOR_ATHEROS is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_BROCADE is not set
+# CONFIG_NET_VENDOR_CHELSIO is not set
+# CONFIG_NET_VENDOR_CISCO is not set
+# CONFIG_NET_VENDOR_DEC is not set
+# CONFIG_NET_VENDOR_DLINK is not set
+# CONFIG_NET_VENDOR_EMULEX is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MELLANOX is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_MYRI is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_NVIDIA is not set
+# CONFIG_NET_VENDOR_OKI is not set
+# CONFIG_NET_VENDOR_QLOGIC is not set
+# CONFIG_NET_VENDOR_RDC is not set
+# CONFIG_NET_VENDOR_REALTEK is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SILAN is not set
+# CONFIG_NET_VENDOR_SIS is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_SUN is not set
+# CONFIG_NET_VENDOR_TEHUTI is not set
+# CONFIG_NET_VENDOR_TI is not set
+# CONFIG_NET_VENDOR_TOSHIBA is not set
+# CONFIG_NET_VENDOR_VIA is not set
+# CONFIG_WLAN is not set
+CONFIG_INPUT_MOUSEDEV=y
+# CONFIG_VT is not set
+CONFIG_LEGACY_PTY_COUNT=16
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_HW_RANDOM=y
+CONFIG_POWER_RESET=y
+CONFIG_POWER_RESET_PIIX4_POWEROFF=y
+CONFIG_POWER_RESET_SYSCON=y
+# CONFIG_HWMON is not set
+CONFIG_FB=y
+CONFIG_FIRMWARE_EDID=y
+CONFIG_FB_MATROX=y
+CONFIG_FB_MATROX_G=y
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+CONFIG_USB_UHCI_HCD=y
+CONFIG_USB_STORAGE=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_DISK=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_BACKLIGHT=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_CMOS=y
+CONFIG_EXT2_FS=y
+CONFIG_EXT3_FS=y
+CONFIG_XFS_FS=y
+CONFIG_XFS_QUOTA=y
+CONFIG_XFS_POSIX_ACL=y
+CONFIG_QUOTA=y
+CONFIG_QFMT_V2=y
+CONFIG_MSDOS_FS=m
+CONFIG_VFAT_FS=m
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_NFS_FS=y
+CONFIG_ROOT_NFS=y
+CONFIG_CIFS=m
+CONFIG_CIFS_XATTR=y
+CONFIG_CIFS_POSIX=y
+CONFIG_NLS_CODEPAGE_437=m
+CONFIG_NLS_ISO8859_1=m
+CONFIG_CRYPTO_PCBC=m
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_WP512=m
+CONFIG_CRYPTO_ANUBIS=m
+CONFIG_CRYPTO_BLOWFISH=m
+CONFIG_CRYPTO_CAST5=m
+CONFIG_CRYPTO_CAST6=m
+CONFIG_CRYPTO_KHAZAD=m
+CONFIG_CRYPTO_SERPENT=m
+CONFIG_CRYPTO_TEA=m
+CONFIG_CRYPTO_TWOFISH=m
+# CONFIG_CRYPTO_HW is not set
+# CONFIG_FTRACE is not set
diff --git a/arch/mips/configs/maltaup_xpa_defconfig b/arch/mips/configs/maltaup_xpa_defconfig
new file mode 100644
index 000000000..75b8da8d9
--- /dev/null
+++ b/arch/mips/configs/maltaup_xpa_defconfig
@@ -0,0 +1,423 @@
+CONFIG_SYSVIPC=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=15
+CONFIG_NAMESPACES=y
+CONFIG_RELAY=y
+CONFIG_EXPERT=y
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_MIPS_MALTA=y
+CONFIG_CPU_LITTLE_ENDIAN=y
+CONFIG_CPU_MIPS32_R2=y
+CONFIG_CPU_MIPS32_R5_FEATURES=y
+CONFIG_CPU_MIPS32_R5_XPA=y
+CONFIG_PAGE_SIZE_16KB=y
+CONFIG_NR_CPUS=2
+CONFIG_HZ_100=y
+CONFIG_PCI=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_XFRM_USER=m
+CONFIG_NET_KEY=y
+CONFIG_NET_KEY_MIGRATE=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_MULTIPLE_TABLES=y
+CONFIG_IP_ROUTE_MULTIPATH=y
+CONFIG_IP_ROUTE_VERBOSE=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_NET_IPIP=m
+CONFIG_IP_MROUTE=y
+CONFIG_IP_PIMSM_V1=y
+CONFIG_IP_PIMSM_V2=y
+CONFIG_SYN_COOKIES=y
+CONFIG_INET_AH=m
+CONFIG_INET_ESP=m
+CONFIG_INET_IPCOMP=m
+CONFIG_TCP_MD5SIG=y
+CONFIG_IPV6_ROUTER_PREF=y
+CONFIG_IPV6_ROUTE_INFO=y
+CONFIG_IPV6_OPTIMISTIC_DAD=y
+CONFIG_INET6_AH=m
+CONFIG_INET6_ESP=m
+CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_TUNNEL=m
+CONFIG_IPV6_MROUTE=y
+CONFIG_IPV6_PIMSM_V2=y
+CONFIG_NETWORK_SECMARK=y
+CONFIG_NETFILTER=y
+CONFIG_NF_CONNTRACK=m
+CONFIG_NF_CONNTRACK_SECMARK=y
+CONFIG_NF_CONNTRACK_EVENTS=y
+CONFIG_NF_CONNTRACK_AMANDA=m
+CONFIG_NF_CONNTRACK_FTP=m
+CONFIG_NF_CONNTRACK_H323=m
+CONFIG_NF_CONNTRACK_IRC=m
+CONFIG_NF_CONNTRACK_PPTP=m
+CONFIG_NF_CONNTRACK_SANE=m
+CONFIG_NF_CONNTRACK_SIP=m
+CONFIG_NF_CONNTRACK_TFTP=m
+CONFIG_NF_CT_NETLINK=m
+CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
+CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
+CONFIG_NETFILTER_XT_TARGET_MARK=m
+CONFIG_NETFILTER_XT_TARGET_NFLOG=m
+CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_TARGET_TRACE=m
+CONFIG_NETFILTER_XT_TARGET_SECMARK=m
+CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
+CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP=m
+CONFIG_NETFILTER_XT_MATCH_COMMENT=m
+CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
+CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
+CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
+CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+CONFIG_NETFILTER_XT_MATCH_DCCP=m
+CONFIG_NETFILTER_XT_MATCH_ESP=m
+CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
+CONFIG_NETFILTER_XT_MATCH_HELPER=m
+CONFIG_NETFILTER_XT_MATCH_IPRANGE=m
+CONFIG_NETFILTER_XT_MATCH_LENGTH=m
+CONFIG_NETFILTER_XT_MATCH_LIMIT=m
+CONFIG_NETFILTER_XT_MATCH_MAC=m
+CONFIG_NETFILTER_XT_MATCH_MARK=m
+CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_OWNER=m
+CONFIG_NETFILTER_XT_MATCH_POLICY=m
+CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
+CONFIG_NETFILTER_XT_MATCH_QUOTA=m
+CONFIG_NETFILTER_XT_MATCH_RATEEST=m
+CONFIG_NETFILTER_XT_MATCH_REALM=m
+CONFIG_NETFILTER_XT_MATCH_RECENT=m
+CONFIG_NETFILTER_XT_MATCH_STATE=m
+CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
+CONFIG_NETFILTER_XT_MATCH_STRING=m
+CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
+CONFIG_NETFILTER_XT_MATCH_TIME=m
+CONFIG_NETFILTER_XT_MATCH_U32=m
+CONFIG_IP_VS=m
+CONFIG_IP_VS_IPV6=y
+CONFIG_IP_VS_PROTO_TCP=y
+CONFIG_IP_VS_PROTO_UDP=y
+CONFIG_IP_VS_PROTO_ESP=y
+CONFIG_IP_VS_PROTO_AH=y
+CONFIG_IP_VS_RR=m
+CONFIG_IP_VS_WRR=m
+CONFIG_IP_VS_LC=m
+CONFIG_IP_VS_WLC=m
+CONFIG_IP_VS_LBLC=m
+CONFIG_IP_VS_LBLCR=m
+CONFIG_IP_VS_DH=m
+CONFIG_IP_VS_SH=m
+CONFIG_IP_VS_SED=m
+CONFIG_IP_VS_NQ=m
+CONFIG_IP_NF_IPTABLES=m
+CONFIG_IP_NF_MATCH_AH=m
+CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_TTL=m
+CONFIG_IP_NF_FILTER=m
+CONFIG_IP_NF_TARGET_REJECT=m
+CONFIG_IP_NF_MANGLE=m
+CONFIG_IP_NF_TARGET_CLUSTERIP=m
+CONFIG_IP_NF_TARGET_ECN=m
+CONFIG_IP_NF_TARGET_TTL=m
+CONFIG_IP_NF_RAW=m
+CONFIG_IP_NF_ARPTABLES=m
+CONFIG_IP_NF_ARPFILTER=m
+CONFIG_IP_NF_ARP_MANGLE=m
+CONFIG_IP6_NF_MATCH_AH=m
+CONFIG_IP6_NF_MATCH_EUI64=m
+CONFIG_IP6_NF_MATCH_FRAG=m
+CONFIG_IP6_NF_MATCH_OPTS=m
+CONFIG_IP6_NF_MATCH_HL=m
+CONFIG_IP6_NF_MATCH_IPV6HEADER=m
+CONFIG_IP6_NF_MATCH_MH=m
+CONFIG_IP6_NF_MATCH_RT=m
+CONFIG_IP6_NF_TARGET_HL=m
+CONFIG_IP6_NF_FILTER=m
+CONFIG_IP6_NF_TARGET_REJECT=m
+CONFIG_IP6_NF_MANGLE=m
+CONFIG_IP6_NF_RAW=m
+CONFIG_BRIDGE_NF_EBTABLES=m
+CONFIG_BRIDGE_EBT_BROUTE=m
+CONFIG_BRIDGE_EBT_T_FILTER=m
+CONFIG_BRIDGE_EBT_T_NAT=m
+CONFIG_BRIDGE_EBT_802_3=m
+CONFIG_BRIDGE_EBT_AMONG=m
+CONFIG_BRIDGE_EBT_ARP=m
+CONFIG_BRIDGE_EBT_IP=m
+CONFIG_BRIDGE_EBT_IP6=m
+CONFIG_BRIDGE_EBT_LIMIT=m
+CONFIG_BRIDGE_EBT_MARK=m
+CONFIG_BRIDGE_EBT_PKTTYPE=m
+CONFIG_BRIDGE_EBT_STP=m
+CONFIG_BRIDGE_EBT_VLAN=m
+CONFIG_BRIDGE_EBT_ARPREPLY=m
+CONFIG_BRIDGE_EBT_DNAT=m
+CONFIG_BRIDGE_EBT_MARK_T=m
+CONFIG_BRIDGE_EBT_REDIRECT=m
+CONFIG_BRIDGE_EBT_SNAT=m
+CONFIG_BRIDGE_EBT_LOG=m
+CONFIG_BRIDGE_EBT_NFLOG=m
+CONFIG_IP_SCTP=m
+CONFIG_BRIDGE=m
+CONFIG_VLAN_8021Q=m
+CONFIG_VLAN_8021Q_GVRP=y
+CONFIG_ATALK=m
+CONFIG_DEV_APPLETALK=m
+CONFIG_IPDDP=m
+CONFIG_IPDDP_ENCAP=y
+CONFIG_PHONET=m
+CONFIG_NET_SCHED=y
+CONFIG_NET_SCH_CBQ=m
+CONFIG_NET_SCH_HTB=m
+CONFIG_NET_SCH_HFSC=m
+CONFIG_NET_SCH_PRIO=m
+CONFIG_NET_SCH_RED=m
+CONFIG_NET_SCH_SFQ=m
+CONFIG_NET_SCH_TEQL=m
+CONFIG_NET_SCH_TBF=m
+CONFIG_NET_SCH_GRED=m
+CONFIG_NET_SCH_DSMARK=m
+CONFIG_NET_SCH_NETEM=m
+CONFIG_NET_SCH_INGRESS=m
+CONFIG_NET_CLS_BASIC=m
+CONFIG_NET_CLS_TCINDEX=m
+CONFIG_NET_CLS_ROUTE4=m
+CONFIG_NET_CLS_FW=m
+CONFIG_NET_CLS_U32=m
+CONFIG_NET_CLS_RSVP=m
+CONFIG_NET_CLS_RSVP6=m
+CONFIG_NET_CLS_FLOW=m
+CONFIG_NET_CLS_ACT=y
+CONFIG_NET_ACT_POLICE=y
+CONFIG_NET_ACT_GACT=m
+CONFIG_GACT_PROB=y
+CONFIG_NET_ACT_MIRRED=m
+CONFIG_NET_ACT_IPT=m
+CONFIG_NET_ACT_NAT=m
+CONFIG_NET_ACT_PEDIT=m
+CONFIG_NET_ACT_SIMP=m
+CONFIG_NET_ACT_SKBEDIT=m
+CONFIG_CFG80211=m
+CONFIG_MAC80211=m
+CONFIG_MAC80211_MESH=y
+CONFIG_RFKILL=m
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+CONFIG_CONNECTOR=m
+CONFIG_MTD=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_OOPS=m
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_CFI_STAA=y
+CONFIG_MTD_PHYSMAP_OF=y
+CONFIG_MTD_UBI=m
+CONFIG_MTD_UBI_GLUEBI=m
+CONFIG_BLK_DEV_FD=m
+CONFIG_BLK_DEV_LOOP=m
+CONFIG_BLK_DEV_NBD=m
+CONFIG_BLK_DEV_RAM=y
+CONFIG_CDROM_PKTCDVD=m
+CONFIG_ATA_OVER_ETH=m
+CONFIG_RAID_ATTRS=m
+CONFIG_BLK_DEV_SD=y
+CONFIG_CHR_DEV_ST=m
+CONFIG_BLK_DEV_SR=y
+CONFIG_CHR_DEV_SG=m
+CONFIG_SCSI_CONSTANTS=y
+CONFIG_SCSI_LOGGING=y
+CONFIG_SCSI_SCAN_ASYNC=y
+CONFIG_SCSI_FC_ATTRS=m
+CONFIG_ISCSI_TCP=m
+CONFIG_BLK_DEV_3W_XXXX_RAID=m
+CONFIG_SCSI_3W_9XXX=m
+CONFIG_SCSI_ACARD=m
+CONFIG_SCSI_AACRAID=m
+CONFIG_SCSI_AIC7XXX=m
+CONFIG_AIC7XXX_RESET_DELAY_MS=15000
+# CONFIG_AIC7XXX_DEBUG_ENABLE is not set
+CONFIG_ATA=y
+CONFIG_ATA_PIIX=y
+CONFIG_PATA_IT8213=m
+CONFIG_PATA_OLDPIIX=y
+CONFIG_PATA_MPIIX=y
+CONFIG_ATA_GENERIC=y
+CONFIG_PATA_LEGACY=y
+CONFIG_MD=y
+CONFIG_BLK_DEV_MD=m
+CONFIG_MD_LINEAR=m
+CONFIG_MD_RAID0=m
+CONFIG_MD_RAID1=m
+CONFIG_MD_RAID10=m
+CONFIG_MD_RAID456=m
+CONFIG_MD_MULTIPATH=m
+CONFIG_MD_FAULTY=m
+CONFIG_BLK_DEV_DM=m
+CONFIG_DM_CRYPT=m
+CONFIG_DM_SNAPSHOT=m
+CONFIG_DM_MIRROR=m
+CONFIG_DM_ZERO=m
+CONFIG_DM_MULTIPATH=m
+CONFIG_NETDEVICES=y
+CONFIG_BONDING=m
+CONFIG_DUMMY=m
+CONFIG_EQUALIZER=m
+CONFIG_IFB=m
+CONFIG_MACVLAN=m
+CONFIG_TUN=m
+CONFIG_VETH=m
+# CONFIG_NET_VENDOR_3COM is not set
+CONFIG_PCNET32=y
+CONFIG_CHELSIO_T3=m
+CONFIG_AX88796=m
+CONFIG_NETXEN_NIC=m
+CONFIG_TC35815=m
+CONFIG_BROADCOM_PHY=m
+CONFIG_CICADA_PHY=m
+CONFIG_DAVICOM_PHY=m
+CONFIG_ICPLUS_PHY=m
+CONFIG_LXT_PHY=m
+CONFIG_MARVELL_PHY=m
+CONFIG_QSEMI_PHY=m
+CONFIG_REALTEK_PHY=m
+CONFIG_SMSC_PHY=m
+CONFIG_VITESSE_PHY=m
+CONFIG_ATMEL=m
+CONFIG_PCI_ATMEL=m
+CONFIG_IPW2100=m
+CONFIG_IPW2100_MONITOR=y
+CONFIG_HOSTAP=m
+CONFIG_HOSTAP_FIRMWARE=y
+CONFIG_HOSTAP_FIRMWARE_NVRAM=y
+CONFIG_HOSTAP_PLX=m
+CONFIG_HOSTAP_PCI=m
+CONFIG_LIBERTAS=m
+CONFIG_INPUT_MOUSEDEV=y
+CONFIG_MOUSE_PS2_ELANTECH=y
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_POWER_RESET=y
+CONFIG_POWER_RESET_PIIX4_POWEROFF=y
+CONFIG_POWER_RESET_SYSCON=y
+# CONFIG_HWMON is not set
+CONFIG_FB=y
+CONFIG_FB_CIRRUS=y
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_HID=m
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_CMOS=y
+CONFIG_UIO=m
+CONFIG_UIO_CIF=m
+CONFIG_EXT2_FS=y
+CONFIG_EXT3_FS=y
+CONFIG_REISERFS_FS=m
+CONFIG_REISERFS_PROC_INFO=y
+CONFIG_REISERFS_FS_XATTR=y
+CONFIG_REISERFS_FS_POSIX_ACL=y
+CONFIG_REISERFS_FS_SECURITY=y
+CONFIG_JFS_FS=m
+CONFIG_JFS_POSIX_ACL=y
+CONFIG_JFS_SECURITY=y
+CONFIG_XFS_FS=m
+CONFIG_XFS_QUOTA=y
+CONFIG_XFS_POSIX_ACL=y
+CONFIG_QUOTA=y
+CONFIG_QFMT_V2=y
+CONFIG_FUSE_FS=m
+CONFIG_ISO9660_FS=m
+CONFIG_JOLIET=y
+CONFIG_ZISOFS=y
+CONFIG_UDF_FS=m
+CONFIG_MSDOS_FS=m
+CONFIG_VFAT_FS=m
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_AFFS_FS=m
+CONFIG_HFS_FS=m
+CONFIG_HFSPLUS_FS=m
+CONFIG_BEFS_FS=m
+CONFIG_BFS_FS=m
+CONFIG_EFS_FS=m
+CONFIG_JFFS2_FS=m
+CONFIG_JFFS2_FS_XATTR=y
+CONFIG_JFFS2_COMPRESSION_OPTIONS=y
+CONFIG_JFFS2_RUBIN=y
+CONFIG_CRAMFS=m
+CONFIG_VXFS_FS=m
+CONFIG_MINIX_FS=m
+CONFIG_ROMFS_FS=m
+CONFIG_SYSV_FS=m
+CONFIG_UFS_FS=m
+CONFIG_NFS_FS=y
+CONFIG_ROOT_NFS=y
+CONFIG_NFSD=y
+CONFIG_NLS_CODEPAGE_437=m
+CONFIG_NLS_CODEPAGE_737=m
+CONFIG_NLS_CODEPAGE_775=m
+CONFIG_NLS_CODEPAGE_850=m
+CONFIG_NLS_CODEPAGE_852=m
+CONFIG_NLS_CODEPAGE_855=m
+CONFIG_NLS_CODEPAGE_857=m
+CONFIG_NLS_CODEPAGE_860=m
+CONFIG_NLS_CODEPAGE_861=m
+CONFIG_NLS_CODEPAGE_862=m
+CONFIG_NLS_CODEPAGE_863=m
+CONFIG_NLS_CODEPAGE_864=m
+CONFIG_NLS_CODEPAGE_865=m
+CONFIG_NLS_CODEPAGE_866=m
+CONFIG_NLS_CODEPAGE_869=m
+CONFIG_NLS_CODEPAGE_936=m
+CONFIG_NLS_CODEPAGE_950=m
+CONFIG_NLS_CODEPAGE_932=m
+CONFIG_NLS_CODEPAGE_949=m
+CONFIG_NLS_CODEPAGE_874=m
+CONFIG_NLS_ISO8859_8=m
+CONFIG_NLS_CODEPAGE_1250=m
+CONFIG_NLS_CODEPAGE_1251=m
+CONFIG_NLS_ASCII=m
+CONFIG_NLS_ISO8859_1=m
+CONFIG_NLS_ISO8859_2=m
+CONFIG_NLS_ISO8859_3=m
+CONFIG_NLS_ISO8859_4=m
+CONFIG_NLS_ISO8859_5=m
+CONFIG_NLS_ISO8859_6=m
+CONFIG_NLS_ISO8859_7=m
+CONFIG_NLS_ISO8859_9=m
+CONFIG_NLS_ISO8859_13=m
+CONFIG_NLS_ISO8859_14=m
+CONFIG_NLS_ISO8859_15=m
+CONFIG_NLS_KOI8_R=m
+CONFIG_NLS_KOI8_U=m
+CONFIG_CRYPTO_CRYPTD=m
+CONFIG_CRYPTO_LRW=m
+CONFIG_CRYPTO_PCBC=m
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_XCBC=m
+CONFIG_CRYPTO_MD4=m
+CONFIG_CRYPTO_SHA512=m
+CONFIG_CRYPTO_WP512=m
+CONFIG_CRYPTO_ANUBIS=m
+CONFIG_CRYPTO_BLOWFISH=m
+CONFIG_CRYPTO_CAMELLIA=m
+CONFIG_CRYPTO_CAST5=m
+CONFIG_CRYPTO_CAST6=m
+CONFIG_CRYPTO_FCRYPT=m
+CONFIG_CRYPTO_KHAZAD=m
+CONFIG_CRYPTO_SERPENT=m
+CONFIG_CRYPTO_TEA=m
+CONFIG_CRYPTO_TWOFISH=m
diff --git a/arch/mips/configs/mtx1_defconfig b/arch/mips/configs/mtx1_defconfig
new file mode 100644
index 000000000..edf9634aa
--- /dev/null
+++ b/arch/mips/configs/mtx1_defconfig
@@ -0,0 +1,684 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_AUDIT=y
+CONFIG_PREEMPT_VOLUNTARY=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_RELAY=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_EXPERT=y
+CONFIG_SLAB=y
+CONFIG_PROFILING=y
+CONFIG_MIPS_ALCHEMY=y
+CONFIG_MIPS_MTX1=y
+CONFIG_PCI=y
+CONFIG_PCCARD=m
+CONFIG_YENTA=m
+CONFIG_PD6729=m
+CONFIG_I82092=m
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_ACORN_PARTITION=y
+CONFIG_ACORN_PARTITION_ICS=y
+CONFIG_ACORN_PARTITION_RISCIX=y
+CONFIG_OSF_PARTITION=y
+CONFIG_AMIGA_PARTITION=y
+CONFIG_ATARI_PARTITION=y
+CONFIG_MAC_PARTITION=y
+CONFIG_BSD_DISKLABEL=y
+CONFIG_MINIX_SUBPARTITION=y
+CONFIG_SOLARIS_X86_PARTITION=y
+CONFIG_UNIXWARE_DISKLABEL=y
+CONFIG_LDM_PARTITION=y
+CONFIG_SGI_PARTITION=y
+CONFIG_ULTRIX_PARTITION=y
+CONFIG_SUN_PARTITION=y
+CONFIG_KARMA_PARTITION=y
+CONFIG_BINFMT_MISC=m
+CONFIG_NET=y
+CONFIG_PACKET=m
+CONFIG_UNIX=y
+CONFIG_XFRM_USER=m
+CONFIG_NET_KEY=m
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_MULTIPLE_TABLES=y
+CONFIG_IP_ROUTE_MULTIPATH=y
+CONFIG_IP_ROUTE_VERBOSE=y
+CONFIG_NET_IPIP=m
+CONFIG_IP_MROUTE=y
+CONFIG_IP_PIMSM_V1=y
+CONFIG_IP_PIMSM_V2=y
+CONFIG_SYN_COOKIES=y
+CONFIG_INET_AH=m
+CONFIG_INET_ESP=m
+CONFIG_INET_IPCOMP=m
+CONFIG_INET6_AH=m
+CONFIG_INET6_ESP=m
+CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_TUNNEL=m
+CONFIG_NETWORK_SECMARK=y
+CONFIG_NETFILTER=y
+CONFIG_NETFILTER_NETLINK_LOG=m
+CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
+CONFIG_NETFILTER_XT_TARGET_DSCP=m
+CONFIG_NETFILTER_XT_TARGET_MARK=m
+CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_TARGET_SECMARK=m
+CONFIG_NETFILTER_XT_MATCH_COMMENT=m
+CONFIG_NETFILTER_XT_MATCH_DSCP=m
+CONFIG_NETFILTER_XT_MATCH_ESP=m
+CONFIG_NETFILTER_XT_MATCH_LENGTH=m
+CONFIG_NETFILTER_XT_MATCH_LIMIT=m
+CONFIG_NETFILTER_XT_MATCH_MAC=m
+CONFIG_NETFILTER_XT_MATCH_MARK=m
+CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_POLICY=m
+CONFIG_NETFILTER_XT_MATCH_PHYSDEV=m
+CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
+CONFIG_NETFILTER_XT_MATCH_QUOTA=m
+CONFIG_NETFILTER_XT_MATCH_REALM=m
+CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
+CONFIG_NETFILTER_XT_MATCH_STRING=m
+CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
+CONFIG_IP_NF_IPTABLES=m
+CONFIG_IP_NF_MATCH_AH=m
+CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_TTL=m
+CONFIG_IP_NF_FILTER=m
+CONFIG_IP_NF_TARGET_REJECT=m
+CONFIG_IP_NF_MANGLE=m
+CONFIG_IP_NF_TARGET_ECN=m
+CONFIG_IP_NF_TARGET_TTL=m
+CONFIG_IP_NF_RAW=m
+CONFIG_IP_NF_ARPTABLES=m
+CONFIG_IP_NF_ARPFILTER=m
+CONFIG_IP_NF_ARP_MANGLE=m
+CONFIG_IP6_NF_IPTABLES=m
+CONFIG_IP6_NF_MATCH_AH=m
+CONFIG_IP6_NF_MATCH_EUI64=m
+CONFIG_IP6_NF_MATCH_FRAG=m
+CONFIG_IP6_NF_MATCH_OPTS=m
+CONFIG_IP6_NF_MATCH_HL=m
+CONFIG_IP6_NF_MATCH_IPV6HEADER=m
+CONFIG_IP6_NF_MATCH_RT=m
+CONFIG_IP6_NF_TARGET_HL=m
+CONFIG_IP6_NF_FILTER=m
+CONFIG_IP6_NF_TARGET_REJECT=m
+CONFIG_IP6_NF_MANGLE=m
+CONFIG_IP6_NF_RAW=m
+CONFIG_BRIDGE_NF_EBTABLES=m
+CONFIG_BRIDGE_EBT_BROUTE=m
+CONFIG_BRIDGE_EBT_T_FILTER=m
+CONFIG_BRIDGE_EBT_T_NAT=m
+CONFIG_BRIDGE_EBT_802_3=m
+CONFIG_BRIDGE_EBT_AMONG=m
+CONFIG_BRIDGE_EBT_ARP=m
+CONFIG_BRIDGE_EBT_IP=m
+CONFIG_BRIDGE_EBT_LIMIT=m
+CONFIG_BRIDGE_EBT_MARK=m
+CONFIG_BRIDGE_EBT_PKTTYPE=m
+CONFIG_BRIDGE_EBT_STP=m
+CONFIG_BRIDGE_EBT_VLAN=m
+CONFIG_BRIDGE_EBT_ARPREPLY=m
+CONFIG_BRIDGE_EBT_DNAT=m
+CONFIG_BRIDGE_EBT_MARK_T=m
+CONFIG_BRIDGE_EBT_REDIRECT=m
+CONFIG_BRIDGE_EBT_SNAT=m
+CONFIG_BRIDGE_EBT_LOG=m
+CONFIG_IP_DCCP=m
+CONFIG_IP_SCTP=m
+CONFIG_TIPC=m
+CONFIG_ATM=y
+CONFIG_ATM_CLIP=y
+CONFIG_ATM_LANE=m
+CONFIG_ATM_MPOA=m
+CONFIG_ATM_BR2684=m
+CONFIG_BRIDGE=m
+CONFIG_VLAN_8021Q=m
+CONFIG_LLC2=m
+CONFIG_ATALK=m
+CONFIG_DEV_APPLETALK=m
+CONFIG_IPDDP=m
+CONFIG_IPDDP_ENCAP=y
+CONFIG_X25=m
+CONFIG_LAPB=m
+CONFIG_NET_SCHED=y
+CONFIG_NET_SCH_CBQ=m
+CONFIG_NET_SCH_HTB=m
+CONFIG_NET_SCH_HFSC=m
+CONFIG_NET_SCH_ATM=m
+CONFIG_NET_SCH_PRIO=m
+CONFIG_NET_SCH_RED=m
+CONFIG_NET_SCH_SFQ=m
+CONFIG_NET_SCH_TEQL=m
+CONFIG_NET_SCH_TBF=m
+CONFIG_NET_SCH_GRED=m
+CONFIG_NET_SCH_DSMARK=m
+CONFIG_NET_SCH_NETEM=m
+CONFIG_NET_SCH_INGRESS=m
+CONFIG_NET_CLS_BASIC=m
+CONFIG_NET_CLS_TCINDEX=m
+CONFIG_NET_CLS_ROUTE4=m
+CONFIG_NET_CLS_FW=m
+CONFIG_NET_CLS_U32=m
+CONFIG_CLS_U32_MARK=y
+CONFIG_NET_CLS_RSVP=m
+CONFIG_NET_CLS_RSVP6=m
+CONFIG_NET_EMATCH=y
+CONFIG_NET_EMATCH_CMP=m
+CONFIG_NET_EMATCH_NBYTE=m
+CONFIG_NET_EMATCH_U32=m
+CONFIG_NET_EMATCH_META=m
+CONFIG_NET_EMATCH_TEXT=m
+CONFIG_NET_CLS_ACT=y
+CONFIG_NET_ACT_POLICE=y
+CONFIG_NET_PKTGEN=m
+CONFIG_HAMRADIO=y
+CONFIG_AX25=m
+# CONFIG_AX25_DAMA_SLAVE is not set
+CONFIG_NETROM=m
+CONFIG_ROSE=m
+CONFIG_MKISS=m
+CONFIG_6PACK=m
+CONFIG_BPQETHER=m
+CONFIG_BAYCOM_SER_FDX=m
+CONFIG_BAYCOM_SER_HDX=m
+CONFIG_YAM=m
+CONFIG_BT=m
+CONFIG_BT_RFCOMM=m
+CONFIG_BT_RFCOMM_TTY=y
+CONFIG_BT_BNEP=m
+CONFIG_BT_BNEP_MC_FILTER=y
+CONFIG_BT_BNEP_PROTO_FILTER=y
+CONFIG_BT_HIDP=m
+CONFIG_BT_HCIUART=m
+CONFIG_BT_HCIUART_H4=y
+CONFIG_BT_HCIUART_BCSP=y
+CONFIG_BT_HCIBCM203X=m
+CONFIG_BT_HCIBPA10X=m
+CONFIG_BT_HCIBFUSB=m
+CONFIG_BT_HCIDTL1=m
+CONFIG_BT_HCIBT3C=m
+CONFIG_BT_HCIBLUECARD=m
+CONFIG_BT_HCIVHCI=m
+CONFIG_CONNECTOR=m
+CONFIG_MTD=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_RAM=m
+CONFIG_MTD_COMPLEX_MAPPINGS=y
+CONFIG_MTD_PHYSMAP=y
+CONFIG_BLK_DEV_NBD=m
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_SIZE=65536
+CONFIG_SCSI=m
+CONFIG_BLK_DEV_SD=m
+CONFIG_CHR_DEV_SG=m
+CONFIG_SCSI_LOGGING=y
+CONFIG_SCSI_SPI_ATTRS=m
+CONFIG_SCSI_FC_ATTRS=m
+CONFIG_SCSI_ISCSI_ATTRS=m
+CONFIG_SCSI_SAS_LIBSAS=m
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_NETDEVICES=y
+CONFIG_BONDING=m
+CONFIG_DUMMY=m
+CONFIG_EQUALIZER=m
+CONFIG_NET_FC=y
+CONFIG_NETCONSOLE=m
+CONFIG_TUN=m
+CONFIG_ARCNET=m
+CONFIG_ARCNET_1201=m
+CONFIG_ARCNET_1051=m
+CONFIG_ARCNET_RAW=m
+CONFIG_ARCNET_CAP=m
+CONFIG_ARCNET_COM90xx=m
+CONFIG_ARCNET_COM90xxIO=m
+CONFIG_ARCNET_RIM_I=m
+CONFIG_ARCNET_COM20020=m
+CONFIG_ARCNET_COM20020_PCI=m
+CONFIG_ARCNET_COM20020_CS=m
+CONFIG_ATM_TCP=m
+CONFIG_ATM_LANAI=m
+CONFIG_ATM_ENI=m
+CONFIG_ATM_NICSTAR=m
+CONFIG_ATM_IDT77252=m
+CONFIG_ATM_IA=m
+CONFIG_ATM_FORE200E=m
+CONFIG_ATM_HE=m
+CONFIG_ATM_HE_USE_SUNI=y
+CONFIG_PCMCIA_3C574=m
+CONFIG_PCMCIA_3C589=m
+CONFIG_VORTEX=m
+CONFIG_TYPHOON=m
+CONFIG_ADAPTEC_STARFIRE=m
+CONFIG_ACENIC=m
+CONFIG_AMD8111_ETH=m
+CONFIG_PCNET32=m
+CONFIG_PCMCIA_NMCLAN=m
+CONFIG_B44=m
+CONFIG_BNX2=m
+CONFIG_TIGON3=m
+CONFIG_CHELSIO_T1=m
+CONFIG_NET_TULIP=y
+CONFIG_DE2104X=m
+CONFIG_TULIP=m
+CONFIG_WINBOND_840=m
+CONFIG_DM9102=m
+CONFIG_ULI526X=m
+CONFIG_PCMCIA_XIRCOM=m
+CONFIG_DL2K=m
+CONFIG_SUNDANCE=m
+CONFIG_PCMCIA_FMVJ18X=m
+CONFIG_E100=m
+CONFIG_E1000=m
+CONFIG_IXGB=m
+CONFIG_SKGE=m
+CONFIG_SKY2=m
+CONFIG_MYRI10GE=m
+CONFIG_FEALNX=m
+CONFIG_NATSEMI=m
+CONFIG_NS83820=m
+CONFIG_S2IO=m
+CONFIG_PCMCIA_AXNET=m
+CONFIG_NE2K_PCI=m
+CONFIG_PCMCIA_PCNET=m
+CONFIG_FORCEDETH=m
+CONFIG_HAMACHI=m
+CONFIG_YELLOWFIN=m
+CONFIG_QLA3XXX=m
+CONFIG_8139CP=m
+CONFIG_8139TOO=m
+# CONFIG_8139TOO_PIO is not set
+CONFIG_8139TOO_8129=y
+CONFIG_R8169=m
+CONFIG_SIS900=m
+CONFIG_SIS190=m
+CONFIG_PCMCIA_SMC91C92=m
+CONFIG_EPIC100=m
+CONFIG_HAPPYMEAL=m
+CONFIG_SUNGEM=m
+CONFIG_CASSINI=m
+CONFIG_TLAN=m
+CONFIG_VIA_RHINE=m
+CONFIG_VIA_VELOCITY=m
+CONFIG_PCMCIA_XIRC2PS=m
+CONFIG_FDDI=y
+CONFIG_DEFXX=m
+CONFIG_SKFP=m
+CONFIG_HIPPI=y
+CONFIG_ROADRUNNER=m
+CONFIG_CICADA_PHY=m
+CONFIG_DAVICOM_PHY=m
+CONFIG_LXT_PHY=m
+CONFIG_MARVELL_PHY=m
+CONFIG_QSEMI_PHY=m
+CONFIG_SMSC_PHY=m
+CONFIG_VITESSE_PHY=m
+CONFIG_PPP=m
+CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_FILTER=y
+CONFIG_PPP_MPPE=m
+CONFIG_PPP_MULTILINK=y
+CONFIG_PPPOATM=m
+CONFIG_PPPOE=m
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
+CONFIG_SLIP=m
+CONFIG_SLIP_COMPRESSED=y
+CONFIG_SLIP_SMART=y
+CONFIG_SLIP_MODE_SLIP6=y
+CONFIG_USB_CATC=m
+CONFIG_USB_KAWETH=m
+CONFIG_USB_PEGASUS=m
+CONFIG_USB_RTL8150=m
+CONFIG_USB_USBNET=m
+CONFIG_USB_NET_GL620A=m
+CONFIG_USB_NET_PLUSB=m
+CONFIG_USB_NET_MCS7830=m
+CONFIG_USB_NET_RNDIS_HOST=m
+CONFIG_USB_ALI_M5632=y
+CONFIG_USB_AN2720=y
+CONFIG_USB_EPSON2888=y
+CONFIG_USB_SIERRA_NET=m
+CONFIG_WAN=y
+CONFIG_HDLC=m
+CONFIG_HDLC_RAW=m
+CONFIG_HDLC_RAW_ETH=m
+CONFIG_HDLC_CISCO=m
+CONFIG_HDLC_FR=m
+CONFIG_HDLC_PPP=m
+CONFIG_HDLC_X25=m
+CONFIG_PCI200SYN=m
+CONFIG_WANXL=m
+CONFIG_FARSYNC=m
+CONFIG_LAPBETHER=m
+# CONFIG_KEYBOARD_ATKBD is not set
+CONFIG_KEYBOARD_GPIO=y
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_SERIO_SERPORT=m
+CONFIG_SERIO_PCIPS2=m
+CONFIG_SERIO_LIBPS2=y
+CONFIG_SERIO_RAW=m
+CONFIG_GAMEPORT=m
+CONFIG_GAMEPORT_NS558=m
+CONFIG_GAMEPORT_L4=m
+CONFIG_GAMEPORT_EMU10K1=m
+CONFIG_GAMEPORT_FM801=m
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_SERIAL_8250=m
+CONFIG_SERIAL_8250_CS=m
+CONFIG_SERIAL_8250_NR_UARTS=48
+CONFIG_SERIAL_8250_EXTENDED=y
+CONFIG_SERIAL_8250_MANY_PORTS=y
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+CONFIG_SERIAL_8250_RSA=y
+CONFIG_SERIAL_JSM=m
+CONFIG_HW_RANDOM=y
+CONFIG_I2C=m
+CONFIG_I2C_CHARDEV=m
+CONFIG_I2C_GPIO=m
+CONFIG_GPIO_SYSFS=y
+CONFIG_SENSORS_ADM1021=m
+CONFIG_SENSORS_ADM1025=m
+CONFIG_SENSORS_ADM1026=m
+CONFIG_SENSORS_ADM1031=m
+CONFIG_SENSORS_ADM9240=m
+CONFIG_SENSORS_ATXP1=m
+CONFIG_SENSORS_DS1621=m
+CONFIG_SENSORS_F71805F=m
+CONFIG_SENSORS_GL518SM=m
+CONFIG_SENSORS_GL520SM=m
+CONFIG_SENSORS_IT87=m
+CONFIG_SENSORS_MAX1619=m
+CONFIG_SENSORS_LM63=m
+CONFIG_SENSORS_LM75=m
+CONFIG_SENSORS_LM77=m
+CONFIG_SENSORS_LM78=m
+CONFIG_SENSORS_LM80=m
+CONFIG_SENSORS_LM83=m
+CONFIG_SENSORS_LM85=m
+CONFIG_SENSORS_LM87=m
+CONFIG_SENSORS_LM90=m
+CONFIG_SENSORS_LM92=m
+CONFIG_SENSORS_PC87360=m
+CONFIG_SENSORS_PCF8591=m
+CONFIG_SENSORS_SIS5595=m
+CONFIG_SENSORS_SMSC47M1=m
+CONFIG_SENSORS_SMSC47M192=m
+CONFIG_SENSORS_SMSC47B397=m
+CONFIG_SENSORS_VIA686A=m
+CONFIG_SENSORS_VT1211=m
+CONFIG_SENSORS_VT8231=m
+CONFIG_SENSORS_W83781D=m
+CONFIG_SENSORS_W83791D=m
+CONFIG_SENSORS_W83792D=m
+CONFIG_SENSORS_W83L785TS=m
+CONFIG_SENSORS_W83627HF=m
+CONFIG_SENSORS_W83627EHF=m
+CONFIG_WATCHDOG=y
+CONFIG_WATCHDOG_NOWAYOUT=y
+CONFIG_WDT_MTX1=y
+# CONFIG_VGA_ARB is not set
+# CONFIG_LCD_CLASS_DEVICE is not set
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_SOUND=m
+CONFIG_SND=m
+CONFIG_SND_SEQUENCER=m
+CONFIG_SND_SEQ_DUMMY=m
+CONFIG_SND_DUMMY=m
+CONFIG_SND_VIRMIDI=m
+CONFIG_SND_MTPAV=m
+CONFIG_SND_SERIAL_U16550=m
+CONFIG_SND_MPU401=m
+CONFIG_SND_AD1889=m
+CONFIG_SND_ATIIXP=m
+CONFIG_SND_ATIIXP_MODEM=m
+CONFIG_SND_AU8810=m
+CONFIG_SND_AU8820=m
+CONFIG_SND_AU8830=m
+CONFIG_SND_BT87X=m
+CONFIG_SND_CA0106=m
+CONFIG_SND_CMIPCI=m
+CONFIG_SND_CS4281=m
+CONFIG_SND_CS46XX=m
+CONFIG_SND_DARLA20=m
+CONFIG_SND_GINA20=m
+CONFIG_SND_LAYLA20=m
+CONFIG_SND_DARLA24=m
+CONFIG_SND_GINA24=m
+CONFIG_SND_LAYLA24=m
+CONFIG_SND_MONA=m
+CONFIG_SND_MIA=m
+CONFIG_SND_ECHO3G=m
+CONFIG_SND_INDIGO=m
+CONFIG_SND_INDIGOIO=m
+CONFIG_SND_INDIGODJ=m
+CONFIG_SND_ENS1370=m
+CONFIG_SND_ENS1371=m
+CONFIG_SND_FM801=m
+CONFIG_SND_HDSP=m
+CONFIG_SND_HDSPM=m
+CONFIG_SND_ICE1724=m
+CONFIG_SND_INTEL8X0=m
+CONFIG_SND_INTEL8X0M=m
+CONFIG_SND_KORG1212=m
+CONFIG_SND_MIXART=m
+CONFIG_SND_NM256=m
+CONFIG_SND_PCXHR=m
+CONFIG_SND_RIPTIDE=m
+CONFIG_SND_RME32=m
+CONFIG_SND_RME96=m
+CONFIG_SND_RME9652=m
+CONFIG_SND_VIA82XX=m
+CONFIG_SND_VIA82XX_MODEM=m
+CONFIG_SND_VX222=m
+CONFIG_SND_YMFPCI=m
+CONFIG_SND_HDA_INTEL=m
+CONFIG_SND_USB_AUDIO=m
+CONFIG_SND_VXPOCKET=m
+CONFIG_SND_PDAUDIOCF=m
+CONFIG_USB_HIDDEV=y
+CONFIG_USB_KBD=m
+CONFIG_USB_MOUSE=m
+CONFIG_USB=m
+CONFIG_USB_MON=m
+CONFIG_USB_EHCI_HCD=m
+CONFIG_USB_EHCI_ROOT_HUB_TT=y
+CONFIG_USB_OHCI_HCD=m
+CONFIG_USB_OHCI_HCD_PLATFORM=m
+CONFIG_USB_UHCI_HCD=m
+CONFIG_USB_U132_HCD=m
+CONFIG_USB_SL811_HCD=m
+CONFIG_USB_SL811_CS=m
+CONFIG_USB_ACM=m
+CONFIG_USB_PRINTER=m
+CONFIG_USB_STORAGE=m
+CONFIG_USB_STORAGE_DATAFAB=m
+CONFIG_USB_STORAGE_FREECOM=m
+CONFIG_USB_STORAGE_ISD200=m
+CONFIG_USB_STORAGE_USBAT=m
+CONFIG_USB_STORAGE_SDDR09=m
+CONFIG_USB_STORAGE_SDDR55=m
+CONFIG_USB_STORAGE_JUMPSHOT=m
+CONFIG_USB_STORAGE_ALAUDA=m
+CONFIG_USB_STORAGE_KARMA=m
+CONFIG_USB_MDC800=m
+CONFIG_USB_MICROTEK=m
+CONFIG_USB_SERIAL=m
+CONFIG_USB_SERIAL_GENERIC=y
+CONFIG_USB_SERIAL_AIRCABLE=m
+CONFIG_USB_SERIAL_ARK3116=m
+CONFIG_USB_SERIAL_BELKIN=m
+CONFIG_USB_SERIAL_WHITEHEAT=m
+CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
+CONFIG_USB_SERIAL_CYPRESS_M8=m
+CONFIG_USB_SERIAL_EMPEG=m
+CONFIG_USB_SERIAL_FTDI_SIO=m
+CONFIG_USB_SERIAL_VISOR=m
+CONFIG_USB_SERIAL_IPAQ=m
+CONFIG_USB_SERIAL_IR=m
+CONFIG_USB_SERIAL_EDGEPORT=m
+CONFIG_USB_SERIAL_EDGEPORT_TI=m
+CONFIG_USB_SERIAL_GARMIN=m
+CONFIG_USB_SERIAL_IPW=m
+CONFIG_USB_SERIAL_KEYSPAN_PDA=m
+CONFIG_USB_SERIAL_KEYSPAN=m
+CONFIG_USB_SERIAL_KLSI=m
+CONFIG_USB_SERIAL_KOBIL_SCT=m
+CONFIG_USB_SERIAL_MCT_U232=m
+CONFIG_USB_SERIAL_MOS7720=m
+CONFIG_USB_SERIAL_MOS7840=m
+CONFIG_USB_SERIAL_NAVMAN=m
+CONFIG_USB_SERIAL_PL2303=m
+CONFIG_USB_SERIAL_SAFE=m
+CONFIG_USB_SERIAL_SIERRAWIRELESS=m
+CONFIG_USB_SERIAL_TI=m
+CONFIG_USB_SERIAL_CYBERJACK=m
+CONFIG_USB_SERIAL_OPTION=m
+CONFIG_USB_SERIAL_OMNINET=m
+CONFIG_USB_EMI62=m
+CONFIG_USB_EMI26=m
+CONFIG_USB_ADUTUX=m
+CONFIG_USB_LEGOTOWER=m
+CONFIG_USB_LCD=m
+CONFIG_USB_CYPRESS_CY7C63=m
+CONFIG_USB_CYTHERM=m
+CONFIG_USB_IDMOUSE=m
+CONFIG_USB_FTDI_ELAN=m
+CONFIG_USB_APPLEDISPLAY=m
+CONFIG_USB_SISUSBVGA=m
+CONFIG_USB_LD=m
+CONFIG_USB_TRANCEVIBRATOR=m
+CONFIG_USB_TEST=m
+CONFIG_USB_ATM=m
+CONFIG_USB_SPEEDTOUCH=m
+CONFIG_USB_CXACRU=m
+CONFIG_USB_UEAGLEATM=m
+CONFIG_USB_XUSBATM=m
+CONFIG_USB_GADGET=m
+CONFIG_USB_ZERO=m
+CONFIG_USB_ETH=m
+CONFIG_USB_GADGETFS=m
+CONFIG_USB_MASS_STORAGE=m
+CONFIG_USB_G_SERIAL=m
+CONFIG_USB_MIDI_GADGET=m
+CONFIG_MMC=m
+CONFIG_MMC_SDHCI=m
+CONFIG_MMC_TIFM_SD=m
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_INTF_DEV_UIE_EMUL=y
+CONFIG_RTC_DRV_TEST=m
+CONFIG_RTC_DRV_DS1307=m
+CONFIG_RTC_DRV_DS1672=m
+CONFIG_RTC_DRV_RS5C372=m
+CONFIG_RTC_DRV_ISL1208=m
+CONFIG_RTC_DRV_X1205=m
+CONFIG_RTC_DRV_PCF8563=m
+CONFIG_RTC_DRV_PCF8583=m
+CONFIG_RTC_DRV_DS1553=m
+CONFIG_RTC_DRV_DS1742=m
+CONFIG_RTC_DRV_M48T86=m
+CONFIG_RTC_DRV_V3020=m
+CONFIG_EXT2_FS=m
+CONFIG_EXT2_FS_XATTR=y
+CONFIG_EXT2_FS_POSIX_ACL=y
+CONFIG_EXT2_FS_SECURITY=y
+CONFIG_EXT3_FS=m
+CONFIG_EXT3_FS_POSIX_ACL=y
+CONFIG_EXT3_FS_SECURITY=y
+CONFIG_QUOTA=y
+CONFIG_AUTOFS4_FS=y
+CONFIG_FUSE_FS=m
+CONFIG_ISO9660_FS=m
+CONFIG_JOLIET=y
+CONFIG_ZISOFS=y
+CONFIG_UDF_FS=m
+CONFIG_MSDOS_FS=m
+CONFIG_VFAT_FS=m
+CONFIG_NTFS_FS=m
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_XATTR=y
+CONFIG_JFFS2_COMPRESSION_OPTIONS=y
+CONFIG_CRAMFS=y
+CONFIG_SQUASHFS=y
+CONFIG_NFS_FS=m
+CONFIG_NFS_V4=m
+CONFIG_NFSD=m
+CONFIG_NFSD_V4=y
+CONFIG_CIFS=m
+CONFIG_CODA_FS=m
+CONFIG_AFS_FS=m
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="cp437"
+CONFIG_NLS_CODEPAGE_437=m
+CONFIG_NLS_CODEPAGE_737=m
+CONFIG_NLS_CODEPAGE_775=m
+CONFIG_NLS_CODEPAGE_850=m
+CONFIG_NLS_CODEPAGE_852=m
+CONFIG_NLS_CODEPAGE_855=m
+CONFIG_NLS_CODEPAGE_857=m
+CONFIG_NLS_CODEPAGE_860=m
+CONFIG_NLS_CODEPAGE_861=m
+CONFIG_NLS_CODEPAGE_862=m
+CONFIG_NLS_CODEPAGE_863=m
+CONFIG_NLS_CODEPAGE_864=m
+CONFIG_NLS_CODEPAGE_865=m
+CONFIG_NLS_CODEPAGE_866=m
+CONFIG_NLS_CODEPAGE_869=m
+CONFIG_NLS_CODEPAGE_936=m
+CONFIG_NLS_CODEPAGE_950=m
+CONFIG_NLS_CODEPAGE_932=m
+CONFIG_NLS_CODEPAGE_949=m
+CONFIG_NLS_CODEPAGE_874=m
+CONFIG_NLS_ISO8859_8=m
+CONFIG_NLS_CODEPAGE_1250=m
+CONFIG_NLS_CODEPAGE_1251=m
+CONFIG_NLS_ASCII=m
+CONFIG_NLS_ISO8859_1=m
+CONFIG_NLS_ISO8859_2=m
+CONFIG_NLS_ISO8859_3=m
+CONFIG_NLS_ISO8859_4=m
+CONFIG_NLS_ISO8859_5=m
+CONFIG_NLS_ISO8859_6=m
+CONFIG_NLS_ISO8859_7=m
+CONFIG_NLS_ISO8859_9=m
+CONFIG_NLS_ISO8859_13=m
+CONFIG_NLS_ISO8859_14=m
+CONFIG_NLS_ISO8859_15=m
+CONFIG_NLS_KOI8_R=m
+CONFIG_NLS_KOI8_U=m
+CONFIG_NLS_UTF8=m
+CONFIG_CRYPTO_TEST=m
+CONFIG_CRYPTO_PCBC=m
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_MD5=y
+CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_WP512=m
+CONFIG_CRYPTO_ANUBIS=m
+CONFIG_CRYPTO_BLOWFISH=m
+CONFIG_CRYPTO_CAST6=m
+CONFIG_CRYPTO_KHAZAD=m
+CONFIG_CRYPTO_SERPENT=m
+CONFIG_CRYPTO_TEA=m
+CONFIG_CRYPTO_TWOFISH=m
+CONFIG_MAGIC_SYSRQ=y
diff --git a/arch/mips/configs/omega2p_defconfig b/arch/mips/configs/omega2p_defconfig
new file mode 100644
index 000000000..91fe2822f
--- /dev/null
+++ b/arch/mips/configs/omega2p_defconfig
@@ -0,0 +1,124 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_CGROUPS=y
+CONFIG_MEMCG=y
+CONFIG_CGROUP_SCHED=y
+CONFIG_CGROUP_FREEZER=y
+CONFIG_CGROUP_DEVICE=y
+CONFIG_CGROUP_CPUACCT=y
+CONFIG_NAMESPACES=y
+CONFIG_USER_NS=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_KALLSYMS_ALL=y
+CONFIG_EMBEDDED=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+# CONFIG_SLUB_DEBUG is not set
+# CONFIG_COMPAT_BRK is not set
+CONFIG_RALINK=y
+CONFIG_SOC_MT7620=y
+CONFIG_DTB_OMEGA2P=y
+CONFIG_CPU_MIPS32_R2=y
+CONFIG_HZ_100=y
+# CONFIG_SECCOMP is not set
+CONFIG_MIPS_CMDLINE_FROM_BOOTLOADER=y
+# CONFIG_SUSPEND is not set
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+# CONFIG_COMPACTION is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+# CONFIG_INET_DIAG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_WIRELESS is not set
+CONFIG_DEVTMPFS=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_ALLOW_DEV_COREDUMP is not set
+CONFIG_NETDEVICES=y
+# CONFIG_ETHERNET is not set
+# CONFIG_WLAN is not set
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_LEGACY_PTY_COUNT=2
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=3
+CONFIG_SERIAL_8250_RUNTIME_UARTS=3
+CONFIG_SERIAL_OF_PLATFORM=y
+# CONFIG_HW_RANDOM is not set
+# CONFIG_HWMON is not set
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_HCD_PLATFORM=y
+CONFIG_MMC=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_MEMORY=y
+CONFIG_PHY_RALINK_USB=y
+# CONFIG_DNOTIFY is not set
+CONFIG_PROC_KCORE=y
+# CONFIG_PROC_PAGE_MONITOR is not set
+CONFIG_TMPFS=y
+CONFIG_CONFIGFS_FS=y
+# CONFIG_NETWORK_FILESYSTEMS is not set
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_737=y
+CONFIG_NLS_CODEPAGE_775=y
+CONFIG_NLS_CODEPAGE_850=y
+CONFIG_NLS_CODEPAGE_852=y
+CONFIG_NLS_CODEPAGE_855=y
+CONFIG_NLS_CODEPAGE_857=y
+CONFIG_NLS_CODEPAGE_860=y
+CONFIG_NLS_CODEPAGE_861=y
+CONFIG_NLS_CODEPAGE_862=y
+CONFIG_NLS_CODEPAGE_863=y
+CONFIG_NLS_CODEPAGE_864=y
+CONFIG_NLS_CODEPAGE_865=y
+CONFIG_NLS_CODEPAGE_866=y
+CONFIG_NLS_CODEPAGE_869=y
+CONFIG_NLS_CODEPAGE_936=y
+CONFIG_NLS_CODEPAGE_950=y
+CONFIG_NLS_CODEPAGE_932=y
+CONFIG_NLS_CODEPAGE_949=y
+CONFIG_NLS_CODEPAGE_874=y
+CONFIG_NLS_ISO8859_8=y
+CONFIG_NLS_CODEPAGE_1250=y
+CONFIG_NLS_CODEPAGE_1251=y
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_ISO8859_2=y
+CONFIG_NLS_ISO8859_3=y
+CONFIG_NLS_ISO8859_4=y
+CONFIG_NLS_ISO8859_5=y
+CONFIG_NLS_ISO8859_6=y
+CONFIG_NLS_ISO8859_7=y
+CONFIG_NLS_ISO8859_9=y
+CONFIG_NLS_ISO8859_13=y
+CONFIG_NLS_ISO8859_14=y
+CONFIG_NLS_ISO8859_15=y
+CONFIG_NLS_KOI8_R=y
+CONFIG_NLS_KOI8_U=y
+CONFIG_NLS_UTF8=y
+CONFIG_CRYPTO_DEFLATE=y
+CONFIG_CRYPTO_LZO=y
+CONFIG_CRC16=y
+CONFIG_XZ_DEC=y
+CONFIG_PRINTK_TIME=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_DEBUG_FS=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_PANIC_TIMEOUT=10
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_PREEMPT is not set
+CONFIG_STACKTRACE=y
+# CONFIG_FTRACE is not set
diff --git a/arch/mips/configs/pic32mzda_defconfig b/arch/mips/configs/pic32mzda_defconfig
new file mode 100644
index 000000000..48dd02d01
--- /dev/null
+++ b/arch/mips/configs/pic32mzda_defconfig
@@ -0,0 +1,86 @@
+CONFIG_SYSVIPC=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT_VOLUNTARY=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_RELAY=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_EMBEDDED=y
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_MACH_PIC32=y
+CONFIG_DTB_PIC32_MZDA_SK=y
+CONFIG_HZ_100=y
+# CONFIG_SECCOMP is not set
+# CONFIG_SUSPEND is not set
+CONFIG_JUMP_LABEL=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+CONFIG_BLK_DEV_BSGLIB=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_SGI_PARTITION=y
+CONFIG_BINFMT_MISC=m
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+# CONFIG_ALLOW_DEV_COREDUMP is not set
+CONFIG_BLK_DEV_LOOP=m
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_SCSI_CONSTANTS=y
+CONFIG_SCSI_SCAN_ASYNC=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_INPUT_LEDS=m
+CONFIG_INPUT_MOUSEDEV=m
+CONFIG_INPUT_EVDEV=y
+CONFIG_INPUT_EVBUG=m
+# CONFIG_KEYBOARD_ATKBD is not set
+CONFIG_KEYBOARD_GPIO=m
+CONFIG_KEYBOARD_GPIO_POLLED=m
+# CONFIG_MOUSE_PS2 is not set
+# CONFIG_SERIO is not set
+CONFIG_SERIAL_PIC32=y
+CONFIG_SERIAL_PIC32_CONSOLE=y
+CONFIG_HW_RANDOM=y
+CONFIG_GPIO_SYSFS=y
+# CONFIG_HWMON is not set
+CONFIG_HIDRAW=y
+# CONFIG_USB_SUPPORT is not set
+CONFIG_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
+CONFIG_MMC_SDHCI_MICROCHIP_PIC32=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=m
+CONFIG_LEDS_TRIGGER_ONESHOT=m
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_GPIO=m
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+# CONFIG_MIPS_PLATFORM_DEVICES is not set
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_EXT4_FS=y
+CONFIG_EXT4_FS_POSIX_ACL=y
+CONFIG_EXT4_FS_SECURITY=y
+CONFIG_AUTOFS4_FS=m
+CONFIG_FUSE_FS=m
+CONFIG_FSCACHE=m
+CONFIG_ISO9660_FS=m
+CONFIG_JOLIET=y
+CONFIG_ZISOFS=y
+CONFIG_UDF_FS=m
+CONFIG_MSDOS_FS=m
+CONFIG_VFAT_FS=m
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_SQUASHFS=m
+CONFIG_SQUASHFS_XATTR=y
+CONFIG_SQUASHFS_LZ4=y
+CONFIG_SQUASHFS_LZO=y
+CONFIG_SQUASHFS_XZ=y
diff --git a/arch/mips/configs/qi_lb60_defconfig b/arch/mips/configs/qi_lb60_defconfig
new file mode 100644
index 000000000..7e5d9741b
--- /dev/null
+++ b/arch/mips/configs/qi_lb60_defconfig
@@ -0,0 +1,177 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SYSVIPC=y
+# CONFIG_CROSS_MEMORY_ATTACH is not set
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_KALLSYMS_ALL=y
+CONFIG_EMBEDDED=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_MACH_INGENIC_SOC=y
+CONFIG_JZ4740_QI_LB60=y
+CONFIG_HZ_100=y
+# CONFIG_SECCOMP is not set
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_EFI_PARTITION is not set
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_CMA=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_MULTIPLE_TABLES=y
+CONFIG_IP_ROUTE_MULTIPATH=y
+CONFIG_IP_ROUTE_VERBOSE=y
+CONFIG_IP_MROUTE=y
+CONFIG_IP_MROUTE_MULTIPLE_TABLES=y
+# CONFIG_INET_DIAG is not set
+CONFIG_TCP_CONG_ADVANCED=y
+# CONFIG_TCP_CONG_BIC is not set
+# CONFIG_TCP_CONG_CUBIC is not set
+CONFIG_TCP_CONG_WESTWOOD=y
+# CONFIG_TCP_CONG_HTCP is not set
+# CONFIG_IPV6 is not set
+CONFIG_MTD=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_RAW_NAND=y
+CONFIG_MTD_NAND_JZ4780=y
+CONFIG_MTD_NAND_JZ4740_ECC=y
+CONFIG_MTD_UBI=y
+CONFIG_NETDEVICES=y
+# CONFIG_WLAN is not set
+CONFIG_INPUT_EVDEV=y
+# CONFIG_KEYBOARD_ATKBD is not set
+CONFIG_KEYBOARD_GPIO=y
+CONFIG_KEYBOARD_MATRIX=y
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_MISC=y
+# CONFIG_SERIO is not set
+CONFIG_LEGACY_PTY_COUNT=2
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+# CONFIG_SERIAL_8250_DMA is not set
+CONFIG_SERIAL_8250_NR_UARTS=2
+CONFIG_SERIAL_8250_RUNTIME_UARTS=2
+CONFIG_SERIAL_8250_INGENIC=y
+# CONFIG_HW_RANDOM is not set
+CONFIG_SPI=y
+CONFIG_SPI_GPIO=y
+CONFIG_POWER_SUPPLY=y
+CONFIG_BATTERY_INGENIC=y
+CONFIG_CHARGER_GPIO=y
+CONFIG_SENSORS_IIO_HWMON=y
+CONFIG_WATCHDOG=y
+CONFIG_JZ4740_WDT=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_DRM=y
+CONFIG_DRM_FBDEV_OVERALLOC=200
+CONFIG_DRM_PANEL_SIMPLE=y
+CONFIG_DRM_INGENIC=y
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+# CONFIG_LOGO_LINUX_VGA16 is not set
+# CONFIG_LOGO_LINUX_CLUT224 is not set
+CONFIG_SOUND=y
+CONFIG_SND=y
+# CONFIG_SND_SUPPORT_OLD_API is not set
+# CONFIG_SND_VERBOSE_PROCFS is not set
+# CONFIG_SND_DRIVERS is not set
+# CONFIG_SND_SPI is not set
+# CONFIG_SND_MIPS is not set
+CONFIG_SND_SOC=y
+CONFIG_SND_JZ4740_SOC_I2S=y
+CONFIG_SND_SOC_JZ4740_CODEC=y
+CONFIG_SND_SOC_SIMPLE_AMPLIFIER=y
+CONFIG_SND_SIMPLE_CARD=y
+CONFIG_USB_MUSB_HDRC=y
+CONFIG_USB_MUSB_JZ4740=y
+CONFIG_USB_INVENTRA_DMA=y
+CONFIG_NOP_USB_XCEIV=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_DEBUG=y
+CONFIG_USB_ETH=y
+# CONFIG_USB_ETH_RNDIS is not set
+CONFIG_MMC=y
+CONFIG_MMC_JZ4740=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_JZ4740=y
+CONFIG_DMADEVICES=y
+CONFIG_DMA_JZ4780=y
+CONFIG_MEMORY=y
+CONFIG_JZ4780_NEMC=y
+CONFIG_IIO=y
+CONFIG_INGENIC_ADC=y
+CONFIG_PWM=y
+CONFIG_PWM_JZ4740=y
+CONFIG_EXT4_FS=y
+# CONFIG_DNOTIFY is not set
+CONFIG_VFAT_FS=y
+CONFIG_PROC_KCORE=y
+# CONFIG_PROC_PAGE_MONITOR is not set
+CONFIG_TMPFS=y
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_SUMMARY=y
+CONFIG_JFFS2_COMPRESSION_OPTIONS=y
+# CONFIG_JFFS2_ZLIB is not set
+CONFIG_UBIFS_FS=y
+CONFIG_UBIFS_FS_ADVANCED_COMPR=y
+# CONFIG_NETWORK_FILESYSTEMS is not set
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_737=y
+CONFIG_NLS_CODEPAGE_775=y
+CONFIG_NLS_CODEPAGE_850=y
+CONFIG_NLS_CODEPAGE_852=y
+CONFIG_NLS_CODEPAGE_855=y
+CONFIG_NLS_CODEPAGE_857=y
+CONFIG_NLS_CODEPAGE_860=y
+CONFIG_NLS_CODEPAGE_861=y
+CONFIG_NLS_CODEPAGE_862=y
+CONFIG_NLS_CODEPAGE_863=y
+CONFIG_NLS_CODEPAGE_864=y
+CONFIG_NLS_CODEPAGE_865=y
+CONFIG_NLS_CODEPAGE_866=y
+CONFIG_NLS_CODEPAGE_869=y
+CONFIG_NLS_CODEPAGE_936=y
+CONFIG_NLS_CODEPAGE_950=y
+CONFIG_NLS_CODEPAGE_932=y
+CONFIG_NLS_CODEPAGE_949=y
+CONFIG_NLS_CODEPAGE_874=y
+CONFIG_NLS_ISO8859_8=y
+CONFIG_NLS_CODEPAGE_1250=y
+CONFIG_NLS_CODEPAGE_1251=y
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_ISO8859_2=y
+CONFIG_NLS_ISO8859_3=y
+CONFIG_NLS_ISO8859_4=y
+CONFIG_NLS_ISO8859_5=y
+CONFIG_NLS_ISO8859_6=y
+CONFIG_NLS_ISO8859_7=y
+CONFIG_NLS_ISO8859_9=y
+CONFIG_NLS_ISO8859_13=y
+CONFIG_NLS_ISO8859_14=y
+CONFIG_NLS_ISO8859_15=y
+CONFIG_NLS_KOI8_R=y
+CONFIG_NLS_KOI8_U=y
+CONFIG_NLS_UTF8=y
+CONFIG_FONTS=y
+CONFIG_FONT_SUN8x16=y
+CONFIG_PRINTK_TIME=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_READABLE_ASM=y
+CONFIG_KGDB=y
+CONFIG_DEBUG_KMEMLEAK=y
+CONFIG_DEBUG_MEMORY_INIT=y
+CONFIG_DEBUG_STACKOVERFLOW=y
+CONFIG_PANIC_ON_OOPS=y
+# CONFIG_FTRACE is not set
diff --git a/arch/mips/configs/rb532_defconfig b/arch/mips/configs/rb532_defconfig
new file mode 100644
index 000000000..93306f5e0
--- /dev/null
+++ b/arch/mips/configs/rb532_defconfig
@@ -0,0 +1,162 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SYSVIPC=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_EXPERT=y
+# CONFIG_ELF_CORE is not set
+# CONFIG_KALLSYMS is not set
+# CONFIG_VM_EVENT_COUNTERS is not set
+CONFIG_SLAB=y
+CONFIG_MIKROTIK_RB532=y
+CONFIG_HZ_100=y
+# CONFIG_SECCOMP is not set
+CONFIG_PCI=y
+# CONFIG_PCI_QUIRKS is not set
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_MAC_PARTITION=y
+CONFIG_BSD_DISKLABEL=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_MULTIPLE_TABLES=y
+CONFIG_IP_ROUTE_MULTIPATH=y
+CONFIG_IP_ROUTE_VERBOSE=y
+CONFIG_SYN_COOKIES=y
+CONFIG_INET_DIAG=m
+CONFIG_TCP_CONG_ADVANCED=y
+CONFIG_TCP_CONG_CUBIC=m
+CONFIG_TCP_CONG_HSTCP=m
+CONFIG_TCP_CONG_HYBLA=m
+CONFIG_TCP_CONG_VEGAS=y
+CONFIG_TCP_CONG_SCALABLE=m
+CONFIG_TCP_CONG_LP=m
+CONFIG_TCP_CONG_VENO=m
+CONFIG_TCP_CONG_YEAH=m
+CONFIG_TCP_CONG_ILLINOIS=m
+# CONFIG_IPV6 is not set
+CONFIG_NETFILTER=y
+# CONFIG_BRIDGE_NETFILTER is not set
+CONFIG_NF_CONNTRACK=y
+CONFIG_NF_CONNTRACK_MARK=y
+CONFIG_NF_CONNTRACK_FTP=m
+CONFIG_NF_CONNTRACK_IRC=m
+CONFIG_NF_CONNTRACK_TFTP=m
+CONFIG_NETFILTER_XT_TARGET_NFLOG=m
+CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_TARGET_TRACE=m
+CONFIG_NETFILTER_XT_MATCH_COMMENT=m
+CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
+CONFIG_NETFILTER_XT_MATCH_DCCP=m
+CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
+CONFIG_NETFILTER_XT_MATCH_LIMIT=y
+CONFIG_NETFILTER_XT_MATCH_MULTIPORT=y
+CONFIG_NETFILTER_XT_MATCH_REALM=m
+CONFIG_NETFILTER_XT_MATCH_SCTP=m
+CONFIG_NETFILTER_XT_MATCH_STATE=y
+CONFIG_NETFILTER_XT_MATCH_U32=m
+CONFIG_IP_NF_IPTABLES=y
+CONFIG_IP_NF_FILTER=y
+CONFIG_IP_NF_TARGET_REJECT=y
+CONFIG_IP_NF_MANGLE=y
+CONFIG_IP_NF_RAW=m
+CONFIG_BRIDGE=y
+CONFIG_VLAN_8021Q=y
+CONFIG_LLC2=m
+CONFIG_NET_SCHED=y
+CONFIG_NET_SCH_CBQ=m
+CONFIG_NET_SCH_PRIO=m
+CONFIG_NET_SCH_NETEM=m
+CONFIG_NET_CLS_BASIC=m
+CONFIG_NET_CLS_TCINDEX=m
+CONFIG_NET_CLS_ROUTE4=m
+CONFIG_NET_CLS_FW=m
+CONFIG_NET_CLS_U32=m
+CONFIG_CLS_U32_PERF=y
+CONFIG_CLS_U32_MARK=y
+CONFIG_NET_CLS_RSVP=m
+CONFIG_NET_CLS_RSVP6=m
+CONFIG_NET_EMATCH=y
+CONFIG_NET_EMATCH_CMP=m
+CONFIG_NET_EMATCH_NBYTE=m
+CONFIG_NET_EMATCH_U32=m
+CONFIG_NET_EMATCH_META=m
+CONFIG_NET_EMATCH_TEXT=m
+CONFIG_NET_CLS_ACT=y
+CONFIG_NET_ACT_POLICE=y
+CONFIG_NET_ACT_GACT=m
+CONFIG_GACT_PROB=y
+CONFIG_NET_ACT_MIRRED=m
+CONFIG_NET_ACT_IPT=m
+CONFIG_NET_ACT_PEDIT=m
+CONFIG_HAMRADIO=y
+CONFIG_MTD=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_BLOCK2MTD=y
+CONFIG_MTD_RAW_NAND=y
+CONFIG_MTD_NAND_PLATFORM=y
+CONFIG_ATA=y
+# CONFIG_ATA_VERBOSE_ERROR is not set
+# CONFIG_SATA_PMP is not set
+CONFIG_PATA_RB532=y
+CONFIG_NETDEVICES=y
+CONFIG_IFB=m
+CONFIG_KORINA=y
+CONFIG_VIA_RHINE=y
+CONFIG_PPP=m
+CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_FILTER=y
+CONFIG_PPP_MULTILINK=y
+CONFIG_PPPOE=m
+CONFIG_PPP_ASYNC=m
+# CONFIG_KEYBOARD_ATKBD is not set
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_MISC=y
+CONFIG_INPUT_RB532_BUTTON=y
+# CONFIG_SERIO is not set
+# CONFIG_VT is not set
+# CONFIG_LEGACY_PTYS is not set
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+# CONFIG_SERIAL_8250_PCI is not set
+CONFIG_SERIAL_8250_NR_UARTS=2
+CONFIG_SERIAL_8250_RUNTIME_UARTS=2
+CONFIG_HW_RANDOM=y
+CONFIG_GPIO_SYSFS=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_WATCHDOG_NOWAYOUT=y
+CONFIG_RC32434_WDT=y
+# CONFIG_VGA_ARB is not set
+# CONFIG_HID is not set
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_MIKROTIK_RB532=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+CONFIG_EXT2_FS=y
+# CONFIG_DNOTIFY is not set
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_CONFIGFS_FS=y
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_SUMMARY=y
+CONFIG_JFFS2_COMPRESSION_OPTIONS=y
+CONFIG_SQUASHFS=y
+CONFIG_CRYPTO_TEST=m
+# CONFIG_CRYPTO_HW is not set
+CONFIG_CRC16=m
+CONFIG_STRIP_ASM_SYMS=y
diff --git a/arch/mips/configs/rbtx49xx_defconfig b/arch/mips/configs/rbtx49xx_defconfig
new file mode 100644
index 000000000..30c195f28
--- /dev/null
+++ b/arch/mips/configs/rbtx49xx_defconfig
@@ -0,0 +1,84 @@
+CONFIG_SYSVIPC=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_EXPERT=y
+# CONFIG_EPOLL is not set
+CONFIG_SLAB=y
+CONFIG_MACH_TX49XX=y
+CONFIG_TOSHIBA_RBTX4927=y
+# CONFIG_SECCOMP is not set
+CONFIG_PCI=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_PNP=y
+# CONFIG_IPV6 is not set
+# CONFIG_WIRELESS is not set
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_BLOCK=m
+CONFIG_MTD_BLOCK_RO=m
+CONFIG_MTD_CFI=y
+CONFIG_MTD_JEDECPROBE=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_COMPLEX_MAPPINGS=y
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_RAW_NAND=m
+CONFIG_MTD_NAND_TXX9NDFMC=m
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_SIZE=8192
+CONFIG_NETDEVICES=y
+CONFIG_NE2000=y
+CONFIG_SMC91X=y
+CONFIG_TC35815=y
+# CONFIG_WLAN is not set
+# CONFIG_INPUT is not set
+# CONFIG_SERIO is not set
+# CONFIG_VT is not set
+CONFIG_SERIAL_TXX9_CONSOLE=y
+CONFIG_SERIAL_TXX9_STDSERIAL=y
+CONFIG_SPI=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_TXX9_WDT=m
+# CONFIG_VGA_ARB is not set
+CONFIG_SOUND=m
+CONFIG_SND=m
+# CONFIG_SND_SUPPORT_OLD_API is not set
+# CONFIG_SND_VERBOSE_PROCFS is not set
+# CONFIG_SND_DRIVERS is not set
+# CONFIG_SND_PCI is not set
+# CONFIG_SND_SPI is not set
+# CONFIG_SND_MIPS is not set
+CONFIG_SND_SOC=m
+# CONFIG_USB_SUPPORT is not set
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_DISK=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_INTF_DEV_UIE_EMUL=y
+CONFIG_RTC_DRV_RS5C348=y
+CONFIG_RTC_DRV_DS1742=y
+CONFIG_DMADEVICES=y
+CONFIG_TXX9_DMAC=m
+# CONFIG_DNOTIFY is not set
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_JFFS2_FS=m
+CONFIG_NFS_FS=y
+CONFIG_ROOT_NFS=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_DEBUG_FS=y
diff --git a/arch/mips/configs/rm200_defconfig b/arch/mips/configs/rm200_defconfig
new file mode 100644
index 000000000..9932a593e
--- /dev/null
+++ b/arch/mips/configs/rm200_defconfig
@@ -0,0 +1,404 @@
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_PREEMPT_VOLUNTARY=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_RELAY=y
+CONFIG_EXPERT=y
+CONFIG_SLAB=y
+CONFIG_SNI_RM=y
+CONFIG_CPU_LITTLE_ENDIAN=y
+CONFIG_ARC_CONSOLE=y
+CONFIG_HZ_1000=y
+CONFIG_PCI=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_BINFMT_MISC=m
+CONFIG_NET=y
+CONFIG_PACKET=m
+CONFIG_UNIX=y
+CONFIG_NET_KEY=m
+CONFIG_NET_KEY_MIGRATE=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_NET_IPIP=m
+CONFIG_IP_MROUTE=y
+CONFIG_IP_PIMSM_V1=y
+CONFIG_IP_PIMSM_V2=y
+CONFIG_TCP_MD5SIG=y
+CONFIG_IPV6_ROUTER_PREF=y
+CONFIG_IPV6_ROUTE_INFO=y
+CONFIG_INET6_AH=m
+CONFIG_INET6_ESP=m
+CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_MIP6=m
+CONFIG_IPV6_TUNNEL=m
+CONFIG_IPV6_MULTIPLE_TABLES=y
+CONFIG_IPV6_SUBTREES=y
+CONFIG_NETWORK_SECMARK=y
+CONFIG_NETFILTER=y
+CONFIG_NF_CONNTRACK=m
+CONFIG_NF_CONNTRACK_SECMARK=y
+CONFIG_NF_CONNTRACK_EVENTS=y
+CONFIG_NF_CONNTRACK_AMANDA=m
+CONFIG_NF_CONNTRACK_FTP=m
+CONFIG_NF_CONNTRACK_H323=m
+CONFIG_NF_CONNTRACK_IRC=m
+CONFIG_NF_CONNTRACK_PPTP=m
+CONFIG_NF_CONNTRACK_SANE=m
+CONFIG_NF_CONNTRACK_SIP=m
+CONFIG_NF_CONNTRACK_TFTP=m
+CONFIG_NF_CT_NETLINK=m
+CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
+CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
+CONFIG_NETFILTER_XT_TARGET_DSCP=m
+CONFIG_NETFILTER_XT_TARGET_MARK=m
+CONFIG_NETFILTER_XT_TARGET_NFLOG=m
+CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_TARGET_SECMARK=m
+CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
+CONFIG_NETFILTER_XT_MATCH_COMMENT=m
+CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
+CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
+CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+CONFIG_NETFILTER_XT_MATCH_DCCP=m
+CONFIG_NETFILTER_XT_MATCH_DSCP=m
+CONFIG_NETFILTER_XT_MATCH_ESP=m
+CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
+CONFIG_NETFILTER_XT_MATCH_HELPER=m
+CONFIG_NETFILTER_XT_MATCH_LENGTH=m
+CONFIG_NETFILTER_XT_MATCH_LIMIT=m
+CONFIG_NETFILTER_XT_MATCH_MAC=m
+CONFIG_NETFILTER_XT_MATCH_MARK=m
+CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_POLICY=m
+CONFIG_NETFILTER_XT_MATCH_PHYSDEV=m
+CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
+CONFIG_NETFILTER_XT_MATCH_QUOTA=m
+CONFIG_NETFILTER_XT_MATCH_REALM=m
+CONFIG_NETFILTER_XT_MATCH_STATE=m
+CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
+CONFIG_NETFILTER_XT_MATCH_STRING=m
+CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
+CONFIG_IP_NF_IPTABLES=m
+CONFIG_IP_NF_MATCH_AH=m
+CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_TTL=m
+CONFIG_IP_NF_FILTER=m
+CONFIG_IP_NF_TARGET_REJECT=m
+CONFIG_IP_NF_MANGLE=m
+CONFIG_IP_NF_TARGET_CLUSTERIP=m
+CONFIG_IP_NF_TARGET_ECN=m
+CONFIG_IP_NF_TARGET_TTL=m
+CONFIG_IP_NF_RAW=m
+CONFIG_IP_NF_ARPTABLES=m
+CONFIG_IP_NF_ARPFILTER=m
+CONFIG_IP_NF_ARP_MANGLE=m
+CONFIG_IP6_NF_IPTABLES=m
+CONFIG_IP6_NF_MATCH_AH=m
+CONFIG_IP6_NF_MATCH_EUI64=m
+CONFIG_IP6_NF_MATCH_FRAG=m
+CONFIG_IP6_NF_MATCH_OPTS=m
+CONFIG_IP6_NF_MATCH_HL=m
+CONFIG_IP6_NF_MATCH_IPV6HEADER=m
+CONFIG_IP6_NF_MATCH_MH=m
+CONFIG_IP6_NF_MATCH_RT=m
+CONFIG_IP6_NF_TARGET_HL=m
+CONFIG_IP6_NF_FILTER=m
+CONFIG_IP6_NF_TARGET_REJECT=m
+CONFIG_IP6_NF_MANGLE=m
+CONFIG_IP6_NF_RAW=m
+CONFIG_BRIDGE_NF_EBTABLES=m
+CONFIG_BRIDGE_EBT_BROUTE=m
+CONFIG_BRIDGE_EBT_T_FILTER=m
+CONFIG_BRIDGE_EBT_T_NAT=m
+CONFIG_BRIDGE_EBT_802_3=m
+CONFIG_BRIDGE_EBT_AMONG=m
+CONFIG_BRIDGE_EBT_ARP=m
+CONFIG_BRIDGE_EBT_IP=m
+CONFIG_BRIDGE_EBT_LIMIT=m
+CONFIG_BRIDGE_EBT_MARK=m
+CONFIG_BRIDGE_EBT_PKTTYPE=m
+CONFIG_BRIDGE_EBT_STP=m
+CONFIG_BRIDGE_EBT_VLAN=m
+CONFIG_BRIDGE_EBT_ARPREPLY=m
+CONFIG_BRIDGE_EBT_DNAT=m
+CONFIG_BRIDGE_EBT_MARK_T=m
+CONFIG_BRIDGE_EBT_REDIRECT=m
+CONFIG_BRIDGE_EBT_SNAT=m
+CONFIG_BRIDGE_EBT_LOG=m
+CONFIG_BRIDGE=m
+CONFIG_NET_SCHED=y
+CONFIG_NET_SCH_CBQ=m
+CONFIG_NET_SCH_HTB=m
+CONFIG_NET_SCH_HFSC=m
+CONFIG_NET_SCH_PRIO=m
+CONFIG_NET_SCH_RED=m
+CONFIG_NET_SCH_SFQ=m
+CONFIG_NET_SCH_TEQL=m
+CONFIG_NET_SCH_TBF=m
+CONFIG_NET_SCH_GRED=m
+CONFIG_NET_SCH_DSMARK=m
+CONFIG_NET_SCH_NETEM=m
+CONFIG_NET_CLS_BASIC=m
+CONFIG_NET_CLS_TCINDEX=m
+CONFIG_NET_CLS_ROUTE4=m
+CONFIG_NET_CLS_FW=m
+CONFIG_NET_CLS_U32=m
+CONFIG_NET_CLS_RSVP=m
+CONFIG_NET_CLS_RSVP6=m
+CONFIG_HAMRADIO=y
+CONFIG_AX25=m
+CONFIG_NETROM=m
+CONFIG_ROSE=m
+CONFIG_MKISS=m
+CONFIG_6PACK=m
+CONFIG_BPQETHER=m
+CONFIG_CONNECTOR=m
+CONFIG_PARPORT=m
+CONFIG_PARPORT_PC=m
+CONFIG_PARPORT_SERIAL=m
+CONFIG_PARPORT_1284=y
+CONFIG_BLK_DEV_FD=m
+CONFIG_PARIDE=m
+CONFIG_PARIDE_PD=m
+CONFIG_PARIDE_PCD=m
+CONFIG_PARIDE_PF=m
+CONFIG_PARIDE_PT=m
+CONFIG_PARIDE_PG=m
+CONFIG_PARIDE_ATEN=m
+CONFIG_PARIDE_BPCK=m
+CONFIG_PARIDE_BPCK6=m
+CONFIG_PARIDE_COMM=m
+CONFIG_PARIDE_DSTR=m
+CONFIG_PARIDE_FIT2=m
+CONFIG_PARIDE_FIT3=m
+CONFIG_PARIDE_EPAT=m
+CONFIG_PARIDE_EPIA=m
+CONFIG_PARIDE_FRIQ=m
+CONFIG_PARIDE_FRPW=m
+CONFIG_PARIDE_KBIC=m
+CONFIG_PARIDE_KTTI=m
+CONFIG_PARIDE_ON20=m
+CONFIG_PARIDE_ON26=m
+CONFIG_BLK_DEV_LOOP=m
+CONFIG_BLK_DEV_NBD=m
+CONFIG_BLK_DEV_RAM=m
+CONFIG_CDROM_PKTCDVD=m
+CONFIG_ATA_OVER_ETH=m
+CONFIG_RAID_ATTRS=m
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_CHR_DEV_ST=m
+CONFIG_BLK_DEV_SR=m
+CONFIG_SCSI_CONSTANTS=y
+CONFIG_SCSI_SCAN_ASYNC=y
+CONFIG_SCSI_FC_ATTRS=y
+CONFIG_ISCSI_TCP=m
+CONFIG_SCSI_AIC94XX=m
+# CONFIG_AIC94XX_DEBUG is not set
+CONFIG_MEGARAID_NEWGEN=y
+CONFIG_MEGARAID_MM=m
+CONFIG_MEGARAID_MAILBOX=m
+CONFIG_SCSI_PPA=m
+CONFIG_SCSI_IMM=m
+CONFIG_SCSI_SYM53C8XX_2=y
+CONFIG_MD=y
+CONFIG_BLK_DEV_MD=m
+CONFIG_MD_LINEAR=m
+CONFIG_MD_RAID0=m
+CONFIG_MD_RAID1=m
+CONFIG_MD_RAID10=m
+CONFIG_MD_RAID456=m
+CONFIG_MD_MULTIPATH=m
+CONFIG_MD_FAULTY=m
+CONFIG_BLK_DEV_DM=m
+CONFIG_DM_SNAPSHOT=m
+CONFIG_DM_MIRROR=m
+CONFIG_DM_ZERO=m
+CONFIG_DM_MULTIPATH=m
+CONFIG_NETDEVICES=y
+CONFIG_BONDING=m
+CONFIG_DUMMY=m
+CONFIG_EQUALIZER=m
+CONFIG_TUN=m
+CONFIG_PCNET32=y
+CONFIG_CHELSIO_T3=m
+CONFIG_NE2000=m
+CONFIG_QLA3XXX=m
+CONFIG_NETXEN_NIC=m
+CONFIG_VIA_VELOCITY=m
+CONFIG_CICADA_PHY=m
+CONFIG_DAVICOM_PHY=m
+CONFIG_LXT_PHY=m
+CONFIG_MARVELL_PHY=m
+CONFIG_QSEMI_PHY=m
+CONFIG_SMSC_PHY=m
+CONFIG_VITESSE_PHY=m
+CONFIG_PLIP=m
+CONFIG_USB_CATC=m
+CONFIG_USB_KAWETH=m
+CONFIG_USB_PEGASUS=m
+CONFIG_USB_RTL8150=m
+CONFIG_USB_USBNET=m
+# CONFIG_USB_NET_CDC_SUBSET is not set
+CONFIG_INPUT_FF_MEMLESS=m
+CONFIG_SERIO_PARKBD=m
+CONFIG_SERIO_RAW=m
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_SERIAL_8250=m
+CONFIG_SERIAL_8250_EXTENDED=y
+CONFIG_SERIAL_8250_SHARE_IRQ=y
+CONFIG_SERIAL_8250_DETECT_IRQ=y
+CONFIG_SERIAL_8250_RSA=y
+CONFIG_PRINTER=m
+CONFIG_PPDEV=m
+# CONFIG_HW_RANDOM is not set
+CONFIG_W1=m
+# CONFIG_HWMON is not set
+CONFIG_HID_PID=y
+CONFIG_USB_HIDDEV=y
+CONFIG_USB_KBD=m
+CONFIG_USB_MOUSE=m
+CONFIG_USB=m
+CONFIG_USB_MON=m
+CONFIG_USB_EHCI_HCD=m
+# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+CONFIG_USB_OHCI_HCD=m
+CONFIG_USB_UHCI_HCD=m
+CONFIG_USB_ACM=m
+CONFIG_USB_PRINTER=m
+CONFIG_USB_STORAGE=m
+CONFIG_USB_STORAGE_DATAFAB=m
+CONFIG_USB_STORAGE_FREECOM=m
+CONFIG_USB_STORAGE_SDDR09=m
+CONFIG_USB_STORAGE_SDDR55=m
+CONFIG_USB_STORAGE_JUMPSHOT=m
+CONFIG_USB_MDC800=m
+CONFIG_USB_MICROTEK=m
+CONFIG_USB_USS720=m
+CONFIG_USB_SERIAL=m
+CONFIG_USB_SERIAL_GENERIC=y
+CONFIG_USB_SERIAL_BELKIN=m
+CONFIG_USB_SERIAL_WHITEHEAT=m
+CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
+CONFIG_USB_SERIAL_CYPRESS_M8=m
+CONFIG_USB_SERIAL_EMPEG=m
+CONFIG_USB_SERIAL_FTDI_SIO=m
+CONFIG_USB_SERIAL_VISOR=m
+CONFIG_USB_SERIAL_IPAQ=m
+CONFIG_USB_SERIAL_IR=m
+CONFIG_USB_SERIAL_EDGEPORT=m
+CONFIG_USB_SERIAL_EDGEPORT_TI=m
+CONFIG_USB_SERIAL_KEYSPAN_PDA=m
+CONFIG_USB_SERIAL_KEYSPAN=m
+CONFIG_USB_SERIAL_KLSI=m
+CONFIG_USB_SERIAL_KOBIL_SCT=m
+CONFIG_USB_SERIAL_MCT_U232=m
+CONFIG_USB_SERIAL_PL2303=m
+CONFIG_USB_SERIAL_SAFE=m
+CONFIG_USB_SERIAL_SAFE_PADDED=y
+CONFIG_USB_SERIAL_CYBERJACK=m
+CONFIG_USB_SERIAL_OMNINET=m
+CONFIG_USB_LEGOTOWER=m
+CONFIG_USB_LCD=m
+CONFIG_USB_CYTHERM=m
+CONFIG_USB_SISUSBVGA=m
+CONFIG_USB_LD=m
+CONFIG_USB_TEST=m
+CONFIG_EXT2_FS=m
+CONFIG_EXT3_FS=y
+CONFIG_REISERFS_FS=m
+CONFIG_REISERFS_FS_XATTR=y
+CONFIG_REISERFS_FS_POSIX_ACL=y
+CONFIG_REISERFS_FS_SECURITY=y
+CONFIG_XFS_FS=m
+CONFIG_XFS_QUOTA=y
+CONFIG_AUTOFS4_FS=m
+CONFIG_FUSE_FS=m
+CONFIG_ISO9660_FS=m
+CONFIG_JOLIET=y
+CONFIG_ZISOFS=y
+CONFIG_UDF_FS=m
+CONFIG_MSDOS_FS=m
+CONFIG_VFAT_FS=m
+CONFIG_NTFS_FS=m
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_ADFS_FS=m
+CONFIG_AFFS_FS=m
+CONFIG_HFS_FS=m
+CONFIG_BEFS_FS=m
+CONFIG_BFS_FS=m
+CONFIG_EFS_FS=m
+CONFIG_CRAMFS=m
+CONFIG_VXFS_FS=m
+CONFIG_MINIX_FS=m
+CONFIG_HPFS_FS=m
+CONFIG_QNX4FS_FS=m
+CONFIG_ROMFS_FS=m
+CONFIG_SYSV_FS=m
+CONFIG_UFS_FS=m
+CONFIG_NFS_FS=m
+CONFIG_NFSD=m
+CONFIG_CIFS=m
+CONFIG_CODA_FS=m
+CONFIG_AFS_FS=m
+CONFIG_NLS_CODEPAGE_437=m
+CONFIG_NLS_CODEPAGE_737=m
+CONFIG_NLS_CODEPAGE_775=m
+CONFIG_NLS_CODEPAGE_850=m
+CONFIG_NLS_CODEPAGE_852=m
+CONFIG_NLS_CODEPAGE_855=m
+CONFIG_NLS_CODEPAGE_857=m
+CONFIG_NLS_CODEPAGE_860=m
+CONFIG_NLS_CODEPAGE_861=m
+CONFIG_NLS_CODEPAGE_862=m
+CONFIG_NLS_CODEPAGE_863=m
+CONFIG_NLS_CODEPAGE_864=m
+CONFIG_NLS_CODEPAGE_865=m
+CONFIG_NLS_CODEPAGE_866=m
+CONFIG_NLS_CODEPAGE_869=m
+CONFIG_NLS_CODEPAGE_936=m
+CONFIG_NLS_CODEPAGE_950=m
+CONFIG_NLS_CODEPAGE_932=m
+CONFIG_NLS_CODEPAGE_949=m
+CONFIG_NLS_CODEPAGE_874=m
+CONFIG_NLS_ISO8859_8=m
+CONFIG_NLS_CODEPAGE_1250=m
+CONFIG_NLS_CODEPAGE_1251=m
+CONFIG_NLS_ASCII=m
+CONFIG_NLS_ISO8859_1=m
+CONFIG_NLS_ISO8859_2=m
+CONFIG_NLS_ISO8859_3=m
+CONFIG_NLS_ISO8859_4=m
+CONFIG_NLS_ISO8859_5=m
+CONFIG_NLS_ISO8859_6=m
+CONFIG_NLS_ISO8859_7=m
+CONFIG_NLS_ISO8859_9=m
+CONFIG_NLS_ISO8859_13=m
+CONFIG_NLS_ISO8859_14=m
+CONFIG_NLS_ISO8859_15=m
+CONFIG_NLS_KOI8_R=m
+CONFIG_NLS_KOI8_U=m
+CONFIG_NLS_UTF8=m
+CONFIG_CRYPTO_LRW=m
+CONFIG_CRYPTO_PCBC=m
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_XCBC=m
+CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_WP512=m
+CONFIG_CRYPTO_ANUBIS=m
+CONFIG_CRYPTO_BLOWFISH=m
+CONFIG_CRYPTO_CAMELLIA=m
+CONFIG_CRYPTO_CAST6=m
+CONFIG_CRYPTO_FCRYPT=m
+CONFIG_CRYPTO_KHAZAD=m
+CONFIG_CRYPTO_SERPENT=m
+CONFIG_CRYPTO_TEA=m
+CONFIG_CRYPTO_TWOFISH=m
diff --git a/arch/mips/configs/rs90_defconfig b/arch/mips/configs/rs90_defconfig
new file mode 100644
index 000000000..7ce3b814f
--- /dev/null
+++ b/arch/mips/configs/rs90_defconfig
@@ -0,0 +1,181 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_DEFAULT_HOSTNAME="rs90"
+# CONFIG_CROSS_MEMORY_ATTACH is not set
+CONFIG_NO_HZ_IDLE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT_VOLUNTARY=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_LD_DEAD_CODE_DATA_ELIMINATION=y
+# CONFIG_SGETMASK_SYSCALL is not set
+# CONFIG_SYSFS_SYSCALL is not set
+# CONFIG_ELF_CORE is not set
+# CONFIG_BASE_FULL is not set
+# CONFIG_TIMERFD is not set
+# CONFIG_AIO is not set
+# CONFIG_IO_URING is not set
+# CONFIG_ADVISE_SYSCALLS is not set
+# CONFIG_KALLSYMS is not set
+CONFIG_EMBEDDED=y
+# CONFIG_PERF_EVENTS is not set
+CONFIG_SLAB=y
+CONFIG_PROFILING=y
+CONFIG_MACH_INGENIC_SOC=y
+CONFIG_JZ4740_RS90=y
+CONFIG_PAGE_SIZE_16KB=y
+CONFIG_HZ_100=y
+# CONFIG_SECCOMP is not set
+CONFIG_MIPS_CMDLINE_DTB_EXTEND=y
+# CONFIG_SUSPEND is not set
+CONFIG_PM=y
+CONFIG_CPU_FREQ=y
+CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE=y
+CONFIG_CPUFREQ_DT=y
+CONFIG_JUMP_LABEL=y
+# CONFIG_STACKPROTECTOR is not set
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_EFI_PARTITION is not set
+# CONFIG_MQ_IOSCHED_DEADLINE is not set
+# CONFIG_MQ_IOSCHED_KYBER is not set
+CONFIG_FRONTSWAP=y
+CONFIG_CMA=y
+CONFIG_ZSMALLOC=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_MULTIPLE_TABLES=y
+CONFIG_IP_ROUTE_MULTIPATH=y
+CONFIG_IP_ROUTE_VERBOSE=y
+CONFIG_IP_MROUTE=y
+CONFIG_IP_MROUTE_MULTIPLE_TABLES=y
+# CONFIG_INET_DIAG is not set
+CONFIG_TCP_CONG_ADVANCED=y
+# CONFIG_TCP_CONG_BIC is not set
+# CONFIG_TCP_CONG_CUBIC is not set
+# CONFIG_TCP_CONG_HTCP is not set
+# CONFIG_IPV6 is not set
+# CONFIG_WIRELESS is not set
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+CONFIG_MTD=y
+CONFIG_MTD_RAW_NAND=y
+CONFIG_MTD_NAND_JZ4780=y
+CONFIG_MTD_NAND_JZ4725B_BCH=y
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_FASTMAP=y
+CONFIG_ZRAM=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_LOOP_MIN_COUNT=0
+CONFIG_NETDEVICES=y
+# CONFIG_ETHERNET is not set
+# CONFIG_WLAN is not set
+CONFIG_INPUT_EVDEV=y
+CONFIG_KEYBOARD_ADC=y
+# CONFIG_KEYBOARD_ATKBD is not set
+CONFIG_KEYBOARD_GPIO=y
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+CONFIG_LEGACY_PTY_COUNT=2
+# CONFIG_HW_RANDOM is not set
+# CONFIG_DEVMEM is not set
+# CONFIG_I2C_COMPAT is not set
+# CONFIG_I2C_HELPER_AUTO is not set
+CONFIG_POWER_SUPPLY=y
+CONFIG_BATTERY_INGENIC=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+# CONFIG_WATCHDOG_HANDLE_BOOT_ENABLED is not set
+CONFIG_JZ4740_WDT=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_DRM=y
+CONFIG_DRM_FBDEV_OVERALLOC=300
+CONFIG_DRM_PANEL_SIMPLE=y
+CONFIG_DRM_INGENIC=y
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+CONFIG_BACKLIGHT_PWM=y
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+# CONFIG_LOGO_LINUX_VGA16 is not set
+# CONFIG_LOGO_LINUX_CLUT224 is not set
+CONFIG_SOUND=y
+CONFIG_SND=y
+# CONFIG_SND_PCM_TIMER is not set
+# CONFIG_SND_SUPPORT_OLD_API is not set
+# CONFIG_SND_PROC_FS is not set
+# CONFIG_SND_DRIVERS is not set
+# CONFIG_SND_MIPS is not set
+CONFIG_SND_SOC=y
+CONFIG_SND_JZ4740_SOC_I2S=y
+CONFIG_SND_SOC_JZ4725B_CODEC=y
+CONFIG_SND_SOC_SIMPLE_AMPLIFIER=y
+CONFIG_SND_SIMPLE_CARD=y
+# CONFIG_HID is not set
+CONFIG_USB_MUSB_HDRC=y
+CONFIG_USB_MUSB_JZ4740=y
+CONFIG_USB_INVENTRA_DMA=y
+CONFIG_NOP_USB_XCEIV=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_VBUS_DRAW=500
+CONFIG_USB_CONFIGFS=y
+CONFIG_USB_CONFIGFS_ECM_SUBSET=y
+CONFIG_USB_CONFIGFS_RNDIS=y
+CONFIG_USB_CONFIGFS_F_FS=y
+CONFIG_MMC=y
+# CONFIG_PWRSEQ_EMMC is not set
+# CONFIG_PWRSEQ_SIMPLE is not set
+CONFIG_MMC_JZ4740=y
+CONFIG_RTC_CLASS=y
+# CONFIG_RTC_HCTOSYS is not set
+# CONFIG_RTC_SYSTOHC is not set
+# CONFIG_RTC_NVMEM is not set
+# CONFIG_RTC_INTF_PROC is not set
+CONFIG_RTC_DRV_JZ4740=y
+CONFIG_DMADEVICES=y
+CONFIG_DMA_JZ4780=y
+# CONFIG_VIRTIO_MENU is not set
+# CONFIG_MIPS_PLATFORM_DEVICES is not set
+CONFIG_INGENIC_OST=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_MEMORY=y
+CONFIG_JZ4780_NEMC=y
+CONFIG_IIO=y
+CONFIG_INGENIC_ADC=y
+CONFIG_IIO_RESCALE=y
+CONFIG_PWM=y
+CONFIG_PWM_JZ4740=y
+# CONFIG_NVMEM is not set
+CONFIG_EXT4_FS=y
+# CONFIG_DNOTIFY is not set
+CONFIG_VFAT_FS=y
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_UBIFS_FS=y
+CONFIG_UBIFS_FS_ADVANCED_COMPR=y
+# CONFIG_UBIFS_FS_ZSTD is not set
+# CONFIG_UBIFS_FS_XATTR is not set
+CONFIG_SQUASHFS=y
+CONFIG_SQUASHFS_FILE_DIRECT=y
+CONFIG_SQUASHFS_DECOMP_MULTI=y
+CONFIG_SQUASHFS_LZO=y
+CONFIG_SQUASHFS_4K_DEVBLK_SIZE=y
+# CONFIG_NETWORK_FILESYSTEMS is not set
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
+# CONFIG_CRYPTO_HW is not set
+CONFIG_FONTS=y
+CONFIG_FONT_6x10=y
+# CONFIG_SYMBOLIC_ERRNAME is not set
+CONFIG_STRIP_ASM_SYMS=y
+# CONFIG_SECTION_MISMATCH_WARN_ONLY is not set
+# CONFIG_DEBUG_MISC is not set
+CONFIG_PANIC_ON_OOPS=y
+# CONFIG_FTRACE is not set
+# CONFIG_RUNTIME_TESTING_MENU is not set
diff --git a/arch/mips/configs/rt305x_defconfig b/arch/mips/configs/rt305x_defconfig
new file mode 100644
index 000000000..bf017d493
--- /dev/null
+++ b/arch/mips/configs/rt305x_defconfig
@@ -0,0 +1,145 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SYSVIPC=y
+# CONFIG_CROSS_MEMORY_ATTACH is not set
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_BLK_DEV_INITRD=y
+# CONFIG_RD_GZIP is not set
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+# CONFIG_AIO is not set
+CONFIG_KALLSYMS_ALL=y
+CONFIG_EMBEDDED=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+# CONFIG_SLUB_DEBUG is not set
+# CONFIG_COMPAT_BRK is not set
+CONFIG_RALINK=y
+CONFIG_DTB_RT305X_EVAL=y
+CONFIG_CPU_MIPS32_R2=y
+CONFIG_HZ_100=y
+# CONFIG_SECCOMP is not set
+# CONFIG_SUSPEND is not set
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_COREDUMP is not set
+# CONFIG_COMPACTION is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_MULTIPLE_TABLES=y
+CONFIG_IP_ROUTE_MULTIPATH=y
+CONFIG_IP_ROUTE_VERBOSE=y
+CONFIG_IP_MROUTE=y
+CONFIG_IP_MROUTE_MULTIPLE_TABLES=y
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_DIAG is not set
+CONFIG_TCP_CONG_ADVANCED=y
+# CONFIG_TCP_CONG_BIC is not set
+# CONFIG_TCP_CONG_WESTWOOD is not set
+# CONFIG_TCP_CONG_HTCP is not set
+# CONFIG_IPV6 is not set
+CONFIG_NETFILTER=y
+# CONFIG_BRIDGE_NETFILTER is not set
+CONFIG_NF_CONNTRACK=m
+CONFIG_NF_CONNTRACK_FTP=m
+CONFIG_NF_CONNTRACK_IRC=m
+CONFIG_NETFILTER_XT_TARGET_CT=m
+CONFIG_NETFILTER_XT_TARGET_LOG=m
+CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
+CONFIG_NETFILTER_XT_MATCH_COMMENT=m
+CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+CONFIG_NETFILTER_XT_MATCH_LIMIT=m
+CONFIG_NETFILTER_XT_MATCH_MAC=m
+CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_STATE=m
+CONFIG_IP_NF_IPTABLES=m
+CONFIG_IP_NF_FILTER=m
+CONFIG_IP_NF_TARGET_REJECT=m
+CONFIG_IP_NF_MANGLE=m
+CONFIG_IP_NF_RAW=m
+CONFIG_BRIDGE=y
+# CONFIG_BRIDGE_IGMP_SNOOPING is not set
+CONFIG_VLAN_8021Q=y
+CONFIG_NET_SCHED=y
+CONFIG_HAMRADIO=y
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_COMPLEX_MAPPINGS=y
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_PHYSMAP_OF=y
+CONFIG_MTD_SPI_NOR=y
+CONFIG_EEPROM_93CX6=m
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_WIZNET is not set
+CONFIG_PHYLIB=y
+CONFIG_PPP=m
+CONFIG_PPP_FILTER=y
+CONFIG_PPP_MULTILINK=y
+CONFIG_PPPOE=m
+CONFIG_PPP_ASYNC=m
+CONFIG_ISDN=y
+CONFIG_INPUT=m
+# CONFIG_KEYBOARD_ATKBD is not set
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_MISC=y
+# CONFIG_SERIO is not set
+# CONFIG_VT is not set
+# CONFIG_LEGACY_PTYS is not set
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_RUNTIME_UARTS=2
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_SPI=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+# CONFIG_HID is not set
+# CONFIG_USB_HID is not set
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_STORAGE_DEBUG=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+CONFIG_STAGING=y
+# CONFIG_IOMMU_SUPPORT is not set
+# CONFIG_DNOTIFY is not set
+# CONFIG_PROC_PAGE_MONITOR is not set
+CONFIG_TMPFS=y
+CONFIG_TMPFS_XATTR=y
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_SUMMARY=y
+CONFIG_JFFS2_FS_XATTR=y
+# CONFIG_JFFS2_FS_POSIX_ACL is not set
+# CONFIG_JFFS2_FS_SECURITY is not set
+CONFIG_JFFS2_COMPRESSION_OPTIONS=y
+# CONFIG_JFFS2_ZLIB is not set
+CONFIG_SQUASHFS=y
+# CONFIG_SQUASHFS_ZLIB is not set
+CONFIG_SQUASHFS_XZ=y
+CONFIG_CRYPTO_ARC4=m
+CONFIG_CRC_ITU_T=m
+CONFIG_CRC32_SARWATE=y
+# CONFIG_XZ_DEC_X86 is not set
+# CONFIG_XZ_DEC_POWERPC is not set
+# CONFIG_XZ_DEC_IA64 is not set
+# CONFIG_XZ_DEC_ARM is not set
+# CONFIG_XZ_DEC_ARMTHUMB is not set
+# CONFIG_XZ_DEC_SPARC is not set
+CONFIG_PRINTK_TIME=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_DEBUG_FS=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_FTRACE is not set
+CONFIG_CMDLINE_BOOL=y
diff --git a/arch/mips/configs/sb1250_swarm_defconfig b/arch/mips/configs/sb1250_swarm_defconfig
new file mode 100644
index 000000000..030186f89
--- /dev/null
+++ b/arch/mips/configs/sb1250_swarm_defconfig
@@ -0,0 +1,103 @@
+CONFIG_SYSVIPC=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_LOG_BUF_SHIFT=15
+CONFIG_CGROUPS=y
+CONFIG_CPUSETS=y
+# CONFIG_PROC_PID_CPUSET is not set
+CONFIG_CGROUP_CPUACCT=y
+CONFIG_NAMESPACES=y
+CONFIG_RELAY=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_EXPERT=y
+# CONFIG_COMPAT_BRK is not set
+CONFIG_SLAB=y
+CONFIG_SIBYTE_SWARM=y
+CONFIG_CPU_SB1_PASS_2_2=y
+CONFIG_64BIT=y
+CONFIG_SMP=y
+CONFIG_NR_CPUS=2
+CONFIG_HZ_1000=y
+CONFIG_MIPS32_O32=y
+CONFIG_PM=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_XFRM_USER=m
+CONFIG_NET_KEY=y
+CONFIG_NET_KEY_MIGRATE=y
+CONFIG_INET=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_TCP_MD5SIG=y
+# CONFIG_IPV6 is not set
+CONFIG_NETWORK_SECMARK=y
+CONFIG_CFG80211=m
+CONFIG_MAC80211=m
+CONFIG_RFKILL=m
+CONFIG_PCI=y
+CONFIG_FW_LOADER=m
+CONFIG_CONNECTOR=m
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_SIZE=9220
+CONFIG_CDROM_PKTCDVD=m
+CONFIG_ATA_OVER_ETH=m
+CONFIG_RAID_ATTRS=m
+CONFIG_BLK_DEV_SD=y
+CONFIG_BLK_DEV_SR=y
+CONFIG_CHR_DEV_SG=y
+CONFIG_SCSI_CONSTANTS=y
+# CONFIG_SCSI_LOWLEVEL is not set
+CONFIG_ATA=y
+# CONFIG_ATA_BMDMA is not set
+CONFIG_PATA_PLATFORM=y
+CONFIG_NETDEVICES=y
+CONFIG_MACVLAN=m
+CONFIG_SB1250_MAC=y
+CONFIG_BROADCOM_PHY=y
+# CONFIG_INPUT is not set
+CONFIG_SERIO_RAW=m
+# CONFIG_VT is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_HWMON is not set
+CONFIG_USB=y
+CONFIG_USB_MON=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_EXT2_FS=y
+CONFIG_EXT2_FS_XATTR=y
+CONFIG_EXT2_FS_POSIX_ACL=y
+CONFIG_EXT2_FS_SECURITY=y
+CONFIG_FUSE_FS=m
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+CONFIG_NFS_FS=y
+CONFIG_ROOT_NFS=y
+CONFIG_CRYPTO_CRYPTD=m
+CONFIG_CRYPTO_AUTHENC=m
+CONFIG_CRYPTO_CBC=m
+CONFIG_CRYPTO_LRW=m
+CONFIG_CRYPTO_PCBC=m
+CONFIG_CRYPTO_XTS=m
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_XCBC=m
+CONFIG_CRYPTO_MD4=m
+CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_SHA512=m
+CONFIG_CRYPTO_WP512=m
+CONFIG_CRYPTO_BLOWFISH=m
+CONFIG_CRYPTO_CAMELLIA=m
+CONFIG_CRYPTO_CAST5=m
+CONFIG_CRYPTO_CAST6=m
+CONFIG_CRYPTO_DES=m
+CONFIG_CRYPTO_FCRYPT=m
+CONFIG_CRYPTO_SERPENT=m
+CONFIG_CRYPTO_TWOFISH=m
+CONFIG_CRYPTO_DEFLATE=m
+CONFIG_CRYPTO_LZO=m
+# CONFIG_CRYPTO_HW is not set
+CONFIG_CRC16=m
diff --git a/arch/mips/configs/vocore2_defconfig b/arch/mips/configs/vocore2_defconfig
new file mode 100644
index 000000000..e47d4cc33
--- /dev/null
+++ b/arch/mips/configs/vocore2_defconfig
@@ -0,0 +1,124 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SYSVIPC=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_CGROUPS=y
+CONFIG_MEMCG=y
+CONFIG_CGROUP_SCHED=y
+CONFIG_CGROUP_FREEZER=y
+CONFIG_CGROUP_DEVICE=y
+CONFIG_CGROUP_CPUACCT=y
+CONFIG_NAMESPACES=y
+CONFIG_USER_NS=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_KALLSYMS_ALL=y
+CONFIG_EMBEDDED=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+# CONFIG_SLUB_DEBUG is not set
+# CONFIG_COMPAT_BRK is not set
+CONFIG_RALINK=y
+CONFIG_SOC_MT7620=y
+CONFIG_DTB_VOCORE2=y
+CONFIG_CPU_MIPS32_R2=y
+CONFIG_HZ_100=y
+# CONFIG_SECCOMP is not set
+CONFIG_MIPS_CMDLINE_FROM_BOOTLOADER=y
+# CONFIG_SUSPEND is not set
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+# CONFIG_COMPACTION is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+# CONFIG_INET_DIAG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_WIRELESS is not set
+CONFIG_DEVTMPFS=y
+# CONFIG_FW_LOADER is not set
+# CONFIG_ALLOW_DEV_COREDUMP is not set
+CONFIG_NETDEVICES=y
+# CONFIG_ETHERNET is not set
+# CONFIG_WLAN is not set
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_LEGACY_PTY_COUNT=2
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_NR_UARTS=3
+CONFIG_SERIAL_8250_RUNTIME_UARTS=3
+CONFIG_SERIAL_OF_PLATFORM=y
+# CONFIG_HW_RANDOM is not set
+# CONFIG_HWMON is not set
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_HCD_PLATFORM=y
+CONFIG_MMC=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_MEMORY=y
+CONFIG_PHY_RALINK_USB=y
+# CONFIG_DNOTIFY is not set
+CONFIG_PROC_KCORE=y
+# CONFIG_PROC_PAGE_MONITOR is not set
+CONFIG_TMPFS=y
+CONFIG_CONFIGFS_FS=y
+# CONFIG_NETWORK_FILESYSTEMS is not set
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_737=y
+CONFIG_NLS_CODEPAGE_775=y
+CONFIG_NLS_CODEPAGE_850=y
+CONFIG_NLS_CODEPAGE_852=y
+CONFIG_NLS_CODEPAGE_855=y
+CONFIG_NLS_CODEPAGE_857=y
+CONFIG_NLS_CODEPAGE_860=y
+CONFIG_NLS_CODEPAGE_861=y
+CONFIG_NLS_CODEPAGE_862=y
+CONFIG_NLS_CODEPAGE_863=y
+CONFIG_NLS_CODEPAGE_864=y
+CONFIG_NLS_CODEPAGE_865=y
+CONFIG_NLS_CODEPAGE_866=y
+CONFIG_NLS_CODEPAGE_869=y
+CONFIG_NLS_CODEPAGE_936=y
+CONFIG_NLS_CODEPAGE_950=y
+CONFIG_NLS_CODEPAGE_932=y
+CONFIG_NLS_CODEPAGE_949=y
+CONFIG_NLS_CODEPAGE_874=y
+CONFIG_NLS_ISO8859_8=y
+CONFIG_NLS_CODEPAGE_1250=y
+CONFIG_NLS_CODEPAGE_1251=y
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_ISO8859_2=y
+CONFIG_NLS_ISO8859_3=y
+CONFIG_NLS_ISO8859_4=y
+CONFIG_NLS_ISO8859_5=y
+CONFIG_NLS_ISO8859_6=y
+CONFIG_NLS_ISO8859_7=y
+CONFIG_NLS_ISO8859_9=y
+CONFIG_NLS_ISO8859_13=y
+CONFIG_NLS_ISO8859_14=y
+CONFIG_NLS_ISO8859_15=y
+CONFIG_NLS_KOI8_R=y
+CONFIG_NLS_KOI8_U=y
+CONFIG_NLS_UTF8=y
+CONFIG_CRYPTO_DEFLATE=y
+CONFIG_CRYPTO_LZO=y
+CONFIG_CRC16=y
+CONFIG_XZ_DEC=y
+CONFIG_PRINTK_TIME=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_DEBUG_FS=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_PANIC_TIMEOUT=10
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_DEBUG_PREEMPT is not set
+CONFIG_STACKTRACE=y
+# CONFIG_FTRACE is not set
diff --git a/arch/mips/configs/xway_defconfig b/arch/mips/configs/xway_defconfig
new file mode 100644
index 000000000..eb5acf1f2
--- /dev/null
+++ b/arch/mips/configs/xway_defconfig
@@ -0,0 +1,151 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SYSVIPC=y
+# CONFIG_CROSS_MEMORY_ATTACH is not set
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_BLK_DEV_INITRD=y
+# CONFIG_RD_GZIP is not set
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+# CONFIG_AIO is not set
+CONFIG_KALLSYMS_ALL=y
+CONFIG_EMBEDDED=y
+# CONFIG_VM_EVENT_COUNTERS is not set
+# CONFIG_SLUB_DEBUG is not set
+# CONFIG_COMPAT_BRK is not set
+CONFIG_LANTIQ=y
+CONFIG_PCI_LANTIQ=y
+CONFIG_CPU_MIPS32_R2=y
+CONFIG_MIPS_VPE_LOADER=y
+CONFIG_NR_CPUS=2
+CONFIG_HZ_100=y
+# CONFIG_SECCOMP is not set
+CONFIG_PCI=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_COREDUMP is not set
+# CONFIG_COMPACTION is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_MULTIPLE_TABLES=y
+CONFIG_IP_ROUTE_MULTIPATH=y
+CONFIG_IP_ROUTE_VERBOSE=y
+CONFIG_IP_MROUTE=y
+CONFIG_IP_MROUTE_MULTIPLE_TABLES=y
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_DIAG is not set
+CONFIG_TCP_CONG_ADVANCED=y
+# CONFIG_TCP_CONG_BIC is not set
+# CONFIG_TCP_CONG_WESTWOOD is not set
+# CONFIG_TCP_CONG_HTCP is not set
+# CONFIG_IPV6 is not set
+CONFIG_NETFILTER=y
+# CONFIG_BRIDGE_NETFILTER is not set
+CONFIG_NF_CONNTRACK=m
+CONFIG_NF_CONNTRACK_FTP=m
+CONFIG_NF_CONNTRACK_IRC=m
+CONFIG_NETFILTER_XT_TARGET_CT=m
+CONFIG_NETFILTER_XT_TARGET_LOG=m
+CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
+CONFIG_NETFILTER_XT_MATCH_COMMENT=m
+CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+CONFIG_NETFILTER_XT_MATCH_LIMIT=m
+CONFIG_NETFILTER_XT_MATCH_MAC=m
+CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_STATE=m
+CONFIG_IP_NF_IPTABLES=m
+CONFIG_IP_NF_FILTER=m
+CONFIG_IP_NF_TARGET_REJECT=m
+CONFIG_IP_NF_MANGLE=m
+CONFIG_IP_NF_RAW=m
+CONFIG_BRIDGE=y
+# CONFIG_BRIDGE_IGMP_SNOOPING is not set
+CONFIG_VLAN_8021Q=y
+CONFIG_NET_SCHED=y
+CONFIG_HAMRADIO=y
+CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_COMPLEX_MAPPINGS=y
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_PHYSMAP_OF=y
+CONFIG_MTD_LANTIQ=y
+CONFIG_MTD_RAW_NAND=y
+CONFIG_MTD_NAND_XWAY=y
+CONFIG_EEPROM_93CX6=m
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_NETDEVICES=y
+CONFIG_LANTIQ_ETOP=y
+# CONFIG_NET_VENDOR_WIZNET is not set
+CONFIG_PHYLIB=y
+CONFIG_INTEL_XWAY_PHY=y
+CONFIG_PPP=m
+CONFIG_PPP_FILTER=y
+CONFIG_PPP_MULTILINK=y
+CONFIG_PPPOE=m
+CONFIG_PPP_ASYNC=m
+CONFIG_ISDN=y
+CONFIG_INPUT=m
+# CONFIG_KEYBOARD_ATKBD is not set
+# CONFIG_INPUT_MOUSE is not set
+CONFIG_INPUT_MISC=y
+# CONFIG_SERIO is not set
+# CONFIG_VT is not set
+# CONFIG_LEGACY_PTYS is not set
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_RUNTIME_UARTS=2
+CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_SERIAL_LANTIQ=y
+CONFIG_SPI=y
+CONFIG_GPIO_MM_LANTIQ=y
+CONFIG_GPIO_STP_XWAY=y
+# CONFIG_HWMON is not set
+CONFIG_WATCHDOG=y
+CONFIG_LANTIQ_WDT=y
+# CONFIG_HID is not set
+# CONFIG_USB_HID is not set
+CONFIG_USB=y
+CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_STORAGE_DEBUG=y
+CONFIG_USB_DWC2=y
+CONFIG_USB_DWC2_PCI=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+CONFIG_STAGING=y
+# CONFIG_IOMMU_SUPPORT is not set
+# CONFIG_DNOTIFY is not set
+# CONFIG_PROC_PAGE_MONITOR is not set
+CONFIG_TMPFS=y
+CONFIG_TMPFS_XATTR=y
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_SUMMARY=y
+CONFIG_JFFS2_FS_XATTR=y
+# CONFIG_JFFS2_FS_POSIX_ACL is not set
+# CONFIG_JFFS2_FS_SECURITY is not set
+CONFIG_JFFS2_COMPRESSION_OPTIONS=y
+# CONFIG_JFFS2_ZLIB is not set
+CONFIG_SQUASHFS=y
+# CONFIG_SQUASHFS_ZLIB is not set
+CONFIG_SQUASHFS_XZ=y
+CONFIG_CRYPTO_ARC4=m
+CONFIG_CRC_ITU_T=m
+CONFIG_CRC32_SARWATE=y
+CONFIG_PRINTK_TIME=y
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_DEBUG_FS=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_FTRACE is not set
+CONFIG_CMDLINE_BOOL=y
diff --git a/arch/mips/crypto/.gitignore b/arch/mips/crypto/.gitignore
new file mode 100644
index 000000000..0d47d4f21
--- /dev/null
+++ b/arch/mips/crypto/.gitignore
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0-only
+poly1305-core.S
diff --git a/arch/mips/crypto/Kconfig b/arch/mips/crypto/Kconfig
new file mode 100644
index 000000000..9003a5c1e
--- /dev/null
+++ b/arch/mips/crypto/Kconfig
@@ -0,0 +1,74 @@
+# SPDX-License-Identifier: GPL-2.0
+
+menu "Accelerated Cryptographic Algorithms for CPU (mips)"
+
+config CRYPTO_CRC32_MIPS
+	tristate "CRC32c and CRC32"
+	depends on MIPS_CRC_SUPPORT
+	select CRYPTO_HASH
+	help
+	  CRC32c and CRC32 CRC algorithms
+
+	  Architecture: mips
+
+config CRYPTO_POLY1305_MIPS
+	tristate "Hash functions: Poly1305"
+	depends on MIPS
+	select CRYPTO_ARCH_HAVE_LIB_POLY1305
+	help
+	  Poly1305 authenticator algorithm (RFC7539)
+
+	  Architecture: mips
+
+config CRYPTO_MD5_OCTEON
+	tristate "Digests: MD5 (OCTEON)"
+	depends on CPU_CAVIUM_OCTEON
+	select CRYPTO_MD5
+	select CRYPTO_HASH
+	help
+	  MD5 message digest algorithm (RFC1321)
+
+	  Architecture: mips OCTEON using crypto instructions, when available
+
+config CRYPTO_SHA1_OCTEON
+	tristate "Hash functions: SHA-1 (OCTEON)"
+	depends on CPU_CAVIUM_OCTEON
+	select CRYPTO_SHA1
+	select CRYPTO_HASH
+	help
+	  SHA-1 secure hash algorithm (FIPS 180)
+
+	  Architecture: mips OCTEON
+
+config CRYPTO_SHA256_OCTEON
+	tristate "Hash functions: SHA-224 and SHA-256 (OCTEON)"
+	depends on CPU_CAVIUM_OCTEON
+	select CRYPTO_SHA256
+	select CRYPTO_HASH
+	help
+	  SHA-224 and SHA-256 secure hash algorithms (FIPS 180)
+
+	  Architecture: mips OCTEON using crypto instructions, when available
+
+config CRYPTO_SHA512_OCTEON
+	tristate "Hash functions: SHA-384 and SHA-512 (OCTEON)"
+	depends on CPU_CAVIUM_OCTEON
+	select CRYPTO_SHA512
+	select CRYPTO_HASH
+	help
+	  SHA-384 and SHA-512 secure hash algorithms (FIPS 180)
+
+	  Architecture: mips OCTEON using crypto instructions, when available
+
+config CRYPTO_CHACHA_MIPS
+	tristate "Ciphers: ChaCha20, XChaCha20, XChaCha12 (MIPS32r2)"
+	depends on CPU_MIPS32_R2
+	select CRYPTO_SKCIPHER
+	select CRYPTO_ARCH_HAVE_LIB_CHACHA
+	help
+	  Length-preserving ciphers: ChaCha20, XChaCha20, and XChaCha12
+	  stream cipher algorithms
+
+	  Architecture: MIPS32r2
+
+endmenu
diff --git a/arch/mips/crypto/Makefile b/arch/mips/crypto/Makefile
new file mode 100644
index 000000000..5e4105ccc
--- /dev/null
+++ b/arch/mips/crypto/Makefile
@@ -0,0 +1,24 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Makefile for MIPS crypto files..
+#
+
+obj-$(CONFIG_CRYPTO_CRC32_MIPS) += crc32-mips.o
+
+obj-$(CONFIG_CRYPTO_CHACHA_MIPS) += chacha-mips.o
+chacha-mips-y := chacha-core.o chacha-glue.o
+AFLAGS_chacha-core.o += -O2 # needed to fill branch delay slots
+
+obj-$(CONFIG_CRYPTO_POLY1305_MIPS) += poly1305-mips.o
+poly1305-mips-y := poly1305-core.o poly1305-glue.o
+
+perlasm-flavour-$(CONFIG_32BIT) := o32
+perlasm-flavour-$(CONFIG_64BIT) := 64
+
+quiet_cmd_perlasm = PERLASM $@
+      cmd_perlasm = $(PERL) $(<) $(perlasm-flavour-y) $(@)
+
+$(obj)/poly1305-core.S: $(src)/poly1305-mips.pl FORCE
+	$(call if_changed,perlasm)
+
+targets += poly1305-core.S
diff --git a/arch/mips/crypto/chacha-core.S b/arch/mips/crypto/chacha-core.S
new file mode 100644
index 000000000..5755f69cf
--- /dev/null
+++ b/arch/mips/crypto/chacha-core.S
@@ -0,0 +1,497 @@
+/* SPDX-License-Identifier: GPL-2.0 OR MIT */
+/*
+ * Copyright (C) 2016-2018 René van Dorst <opensource@vdorst.com>. All Rights Reserved.
+ * Copyright (C) 2015-2019 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
+ */
+
+#define MASK_U32		0x3c
+#define CHACHA20_BLOCK_SIZE	64
+#define STACK_SIZE		32
+
+#define X0	$t0
+#define X1	$t1
+#define X2	$t2
+#define X3	$t3
+#define X4	$t4
+#define X5	$t5
+#define X6	$t6
+#define X7	$t7
+#define X8	$t8
+#define X9	$t9
+#define X10	$v1
+#define X11	$s6
+#define X12	$s5
+#define X13	$s4
+#define X14	$s3
+#define X15	$s2
+/* Use regs which are overwritten on exit for Tx so we don't leak clear data. */
+#define T0	$s1
+#define T1	$s0
+#define T(n)	T ## n
+#define X(n)	X ## n
+
+/* Input arguments */
+#define STATE		$a0
+#define OUT		$a1
+#define IN		$a2
+#define BYTES		$a3
+
+/* Output argument */
+/* NONCE[0] is kept in a register and not in memory.
+ * We don't want to touch original value in memory.
+ * Must be incremented every loop iteration.
+ */
+#define NONCE_0		$v0
+
+/* SAVED_X and SAVED_CA are set in the jump table.
+ * Use regs which are overwritten on exit else we don't leak clear data.
+ * They are used to handling the last bytes which are not multiple of 4.
+ */
+#define SAVED_X		X15
+#define SAVED_CA	$s7
+
+#define IS_UNALIGNED	$s7
+
+#if __BYTE_ORDER__ == __ORDER_BIG_ENDIAN__
+#define MSB 0
+#define LSB 3
+#define ROTx rotl
+#define ROTR(n) rotr n, 24
+#define	CPU_TO_LE32(n) \
+	wsbh	n; \
+	rotr	n, 16;
+#else
+#define MSB 3
+#define LSB 0
+#define ROTx rotr
+#define CPU_TO_LE32(n)
+#define ROTR(n)
+#endif
+
+#define FOR_EACH_WORD(x) \
+	x( 0); \
+	x( 1); \
+	x( 2); \
+	x( 3); \
+	x( 4); \
+	x( 5); \
+	x( 6); \
+	x( 7); \
+	x( 8); \
+	x( 9); \
+	x(10); \
+	x(11); \
+	x(12); \
+	x(13); \
+	x(14); \
+	x(15);
+
+#define FOR_EACH_WORD_REV(x) \
+	x(15); \
+	x(14); \
+	x(13); \
+	x(12); \
+	x(11); \
+	x(10); \
+	x( 9); \
+	x( 8); \
+	x( 7); \
+	x( 6); \
+	x( 5); \
+	x( 4); \
+	x( 3); \
+	x( 2); \
+	x( 1); \
+	x( 0);
+
+#define PLUS_ONE_0	 1
+#define PLUS_ONE_1	 2
+#define PLUS_ONE_2	 3
+#define PLUS_ONE_3	 4
+#define PLUS_ONE_4	 5
+#define PLUS_ONE_5	 6
+#define PLUS_ONE_6	 7
+#define PLUS_ONE_7	 8
+#define PLUS_ONE_8	 9
+#define PLUS_ONE_9	10
+#define PLUS_ONE_10	11
+#define PLUS_ONE_11	12
+#define PLUS_ONE_12	13
+#define PLUS_ONE_13	14
+#define PLUS_ONE_14	15
+#define PLUS_ONE_15	16
+#define PLUS_ONE(x)	PLUS_ONE_ ## x
+#define _CONCAT3(a,b,c)	a ## b ## c
+#define CONCAT3(a,b,c)	_CONCAT3(a,b,c)
+
+#define STORE_UNALIGNED(x) \
+CONCAT3(.Lchacha_mips_xor_unaligned_, PLUS_ONE(x), _b: ;) \
+	.if (x != 12); \
+		lw	T0, (x*4)(STATE); \
+	.endif; \
+	lwl	T1, (x*4)+MSB ## (IN); \
+	lwr	T1, (x*4)+LSB ## (IN); \
+	.if (x == 12); \
+		addu	X ## x, NONCE_0; \
+	.else; \
+		addu	X ## x, T0; \
+	.endif; \
+	CPU_TO_LE32(X ## x); \
+	xor	X ## x, T1; \
+	swl	X ## x, (x*4)+MSB ## (OUT); \
+	swr	X ## x, (x*4)+LSB ## (OUT);
+
+#define STORE_ALIGNED(x) \
+CONCAT3(.Lchacha_mips_xor_aligned_, PLUS_ONE(x), _b: ;) \
+	.if (x != 12); \
+		lw	T0, (x*4)(STATE); \
+	.endif; \
+	lw	T1, (x*4) ## (IN); \
+	.if (x == 12); \
+		addu	X ## x, NONCE_0; \
+	.else; \
+		addu	X ## x, T0; \
+	.endif; \
+	CPU_TO_LE32(X ## x); \
+	xor	X ## x, T1; \
+	sw	X ## x, (x*4) ## (OUT);
+
+/* Jump table macro.
+ * Used for setup and handling the last bytes, which are not multiple of 4.
+ * X15 is free to store Xn
+ * Every jumptable entry must be equal in size.
+ */
+#define JMPTBL_ALIGNED(x) \
+.Lchacha_mips_jmptbl_aligned_ ## x: ; \
+	.set	noreorder; \
+	b	.Lchacha_mips_xor_aligned_ ## x ## _b; \
+	.if (x == 12); \
+		addu	SAVED_X, X ## x, NONCE_0; \
+	.else; \
+		addu	SAVED_X, X ## x, SAVED_CA; \
+	.endif; \
+	.set	reorder
+
+#define JMPTBL_UNALIGNED(x) \
+.Lchacha_mips_jmptbl_unaligned_ ## x: ; \
+	.set	noreorder; \
+	b	.Lchacha_mips_xor_unaligned_ ## x ## _b; \
+	.if (x == 12); \
+		addu	SAVED_X, X ## x, NONCE_0; \
+	.else; \
+		addu	SAVED_X, X ## x, SAVED_CA; \
+	.endif; \
+	.set	reorder
+
+#define AXR(A, B, C, D,  K, L, M, N,  V, W, Y, Z,  S) \
+	addu	X(A), X(K); \
+	addu	X(B), X(L); \
+	addu	X(C), X(M); \
+	addu	X(D), X(N); \
+	xor	X(V), X(A); \
+	xor	X(W), X(B); \
+	xor	X(Y), X(C); \
+	xor	X(Z), X(D); \
+	rotl	X(V), S;    \
+	rotl	X(W), S;    \
+	rotl	X(Y), S;    \
+	rotl	X(Z), S;
+
+.text
+.set	reorder
+.set	noat
+.globl	chacha_crypt_arch
+.ent	chacha_crypt_arch
+chacha_crypt_arch:
+	.frame	$sp, STACK_SIZE, $ra
+
+	/* Load number of rounds */
+	lw	$at, 16($sp)
+
+	addiu	$sp, -STACK_SIZE
+
+	/* Return bytes = 0. */
+	beqz	BYTES, .Lchacha_mips_end
+
+	lw	NONCE_0, 48(STATE)
+
+	/* Save s0-s7 */
+	sw	$s0,  0($sp)
+	sw	$s1,  4($sp)
+	sw	$s2,  8($sp)
+	sw	$s3, 12($sp)
+	sw	$s4, 16($sp)
+	sw	$s5, 20($sp)
+	sw	$s6, 24($sp)
+	sw	$s7, 28($sp)
+
+	/* Test IN or OUT is unaligned.
+	 * IS_UNALIGNED = ( IN | OUT ) & 0x00000003
+	 */
+	or	IS_UNALIGNED, IN, OUT
+	andi	IS_UNALIGNED, 0x3
+
+	b	.Lchacha_rounds_start
+
+.align 4
+.Loop_chacha_rounds:
+	addiu	IN,  CHACHA20_BLOCK_SIZE
+	addiu	OUT, CHACHA20_BLOCK_SIZE
+	addiu	NONCE_0, 1
+
+.Lchacha_rounds_start:
+	lw	X0,  0(STATE)
+	lw	X1,  4(STATE)
+	lw	X2,  8(STATE)
+	lw	X3,  12(STATE)
+
+	lw	X4,  16(STATE)
+	lw	X5,  20(STATE)
+	lw	X6,  24(STATE)
+	lw	X7,  28(STATE)
+	lw	X8,  32(STATE)
+	lw	X9,  36(STATE)
+	lw	X10, 40(STATE)
+	lw	X11, 44(STATE)
+
+	move	X12, NONCE_0
+	lw	X13, 52(STATE)
+	lw	X14, 56(STATE)
+	lw	X15, 60(STATE)
+
+.Loop_chacha_xor_rounds:
+	addiu	$at, -2
+	AXR( 0, 1, 2, 3,  4, 5, 6, 7, 12,13,14,15, 16);
+	AXR( 8, 9,10,11, 12,13,14,15,  4, 5, 6, 7, 12);
+	AXR( 0, 1, 2, 3,  4, 5, 6, 7, 12,13,14,15,  8);
+	AXR( 8, 9,10,11, 12,13,14,15,  4, 5, 6, 7,  7);
+	AXR( 0, 1, 2, 3,  5, 6, 7, 4, 15,12,13,14, 16);
+	AXR(10,11, 8, 9, 15,12,13,14,  5, 6, 7, 4, 12);
+	AXR( 0, 1, 2, 3,  5, 6, 7, 4, 15,12,13,14,  8);
+	AXR(10,11, 8, 9, 15,12,13,14,  5, 6, 7, 4,  7);
+	bnez	$at, .Loop_chacha_xor_rounds
+
+	addiu	BYTES, -(CHACHA20_BLOCK_SIZE)
+
+	/* Is data src/dst unaligned? Jump */
+	bnez	IS_UNALIGNED, .Loop_chacha_unaligned
+
+	/* Set number rounds here to fill delayslot. */
+	lw	$at, (STACK_SIZE+16)($sp)
+
+	/* BYTES < 0, it has no full block. */
+	bltz	BYTES, .Lchacha_mips_no_full_block_aligned
+
+	FOR_EACH_WORD_REV(STORE_ALIGNED)
+
+	/* BYTES > 0? Loop again. */
+	bgtz	BYTES, .Loop_chacha_rounds
+
+	/* Place this here to fill delay slot */
+	addiu	NONCE_0, 1
+
+	/* BYTES < 0? Handle last bytes */
+	bltz	BYTES, .Lchacha_mips_xor_bytes
+
+.Lchacha_mips_xor_done:
+	/* Restore used registers */
+	lw	$s0,  0($sp)
+	lw	$s1,  4($sp)
+	lw	$s2,  8($sp)
+	lw	$s3, 12($sp)
+	lw	$s4, 16($sp)
+	lw	$s5, 20($sp)
+	lw	$s6, 24($sp)
+	lw	$s7, 28($sp)
+
+	/* Write NONCE_0 back to right location in state */
+	sw	NONCE_0, 48(STATE)
+
+.Lchacha_mips_end:
+	addiu	$sp, STACK_SIZE
+	jr	$ra
+
+.Lchacha_mips_no_full_block_aligned:
+	/* Restore the offset on BYTES */
+	addiu	BYTES, CHACHA20_BLOCK_SIZE
+
+	/* Get number of full WORDS */
+	andi	$at, BYTES, MASK_U32
+
+	/* Load upper half of jump table addr */
+	lui	T0, %hi(.Lchacha_mips_jmptbl_aligned_0)
+
+	/* Calculate lower half jump table offset */
+	ins	T0, $at, 1, 6
+
+	/* Add offset to STATE */
+	addu	T1, STATE, $at
+
+	/* Add lower half jump table addr */
+	addiu	T0, %lo(.Lchacha_mips_jmptbl_aligned_0)
+
+	/* Read value from STATE */
+	lw	SAVED_CA, 0(T1)
+
+	/* Store remaining bytecounter as negative value */
+	subu	BYTES, $at, BYTES
+
+	jr	T0
+
+	/* Jump table */
+	FOR_EACH_WORD(JMPTBL_ALIGNED)
+
+
+.Loop_chacha_unaligned:
+	/* Set number rounds here to fill delayslot. */
+	lw	$at, (STACK_SIZE+16)($sp)
+
+	/* BYTES > 0, it has no full block. */
+	bltz	BYTES, .Lchacha_mips_no_full_block_unaligned
+
+	FOR_EACH_WORD_REV(STORE_UNALIGNED)
+
+	/* BYTES > 0? Loop again. */
+	bgtz	BYTES, .Loop_chacha_rounds
+
+	/* Write NONCE_0 back to right location in state */
+	sw	NONCE_0, 48(STATE)
+
+	.set noreorder
+	/* Fall through to byte handling */
+	bgez	BYTES, .Lchacha_mips_xor_done
+.Lchacha_mips_xor_unaligned_0_b:
+.Lchacha_mips_xor_aligned_0_b:
+	/* Place this here to fill delay slot */
+	addiu	NONCE_0, 1
+	.set reorder
+
+.Lchacha_mips_xor_bytes:
+	addu	IN, $at
+	addu	OUT, $at
+	/* First byte */
+	lbu	T1, 0(IN)
+	addiu	$at, BYTES, 1
+	CPU_TO_LE32(SAVED_X)
+	ROTR(SAVED_X)
+	xor	T1, SAVED_X
+	sb	T1, 0(OUT)
+	beqz	$at, .Lchacha_mips_xor_done
+	/* Second byte */
+	lbu	T1, 1(IN)
+	addiu	$at, BYTES, 2
+	ROTx	SAVED_X, 8
+	xor	T1, SAVED_X
+	sb	T1, 1(OUT)
+	beqz	$at, .Lchacha_mips_xor_done
+	/* Third byte */
+	lbu	T1, 2(IN)
+	ROTx	SAVED_X, 8
+	xor	T1, SAVED_X
+	sb	T1, 2(OUT)
+	b	.Lchacha_mips_xor_done
+
+.Lchacha_mips_no_full_block_unaligned:
+	/* Restore the offset on BYTES */
+	addiu	BYTES, CHACHA20_BLOCK_SIZE
+
+	/* Get number of full WORDS */
+	andi	$at, BYTES, MASK_U32
+
+	/* Load upper half of jump table addr */
+	lui	T0, %hi(.Lchacha_mips_jmptbl_unaligned_0)
+
+	/* Calculate lower half jump table offset */
+	ins	T0, $at, 1, 6
+
+	/* Add offset to STATE */
+	addu	T1, STATE, $at
+
+	/* Add lower half jump table addr */
+	addiu	T0, %lo(.Lchacha_mips_jmptbl_unaligned_0)
+
+	/* Read value from STATE */
+	lw	SAVED_CA, 0(T1)
+
+	/* Store remaining bytecounter as negative value */
+	subu	BYTES, $at, BYTES
+
+	jr	T0
+
+	/* Jump table */
+	FOR_EACH_WORD(JMPTBL_UNALIGNED)
+.end chacha_crypt_arch
+.set at
+
+/* Input arguments
+ * STATE	$a0
+ * OUT		$a1
+ * NROUND	$a2
+ */
+
+#undef X12
+#undef X13
+#undef X14
+#undef X15
+
+#define X12	$a3
+#define X13	$at
+#define X14	$v0
+#define X15	STATE
+
+.set noat
+.globl	hchacha_block_arch
+.ent	hchacha_block_arch
+hchacha_block_arch:
+	.frame	$sp, STACK_SIZE, $ra
+
+	addiu	$sp, -STACK_SIZE
+
+	/* Save X11(s6) */
+	sw	X11, 0($sp)
+
+	lw	X0,  0(STATE)
+	lw	X1,  4(STATE)
+	lw	X2,  8(STATE)
+	lw	X3,  12(STATE)
+	lw	X4,  16(STATE)
+	lw	X5,  20(STATE)
+	lw	X6,  24(STATE)
+	lw	X7,  28(STATE)
+	lw	X8,  32(STATE)
+	lw	X9,  36(STATE)
+	lw	X10, 40(STATE)
+	lw	X11, 44(STATE)
+	lw	X12, 48(STATE)
+	lw	X13, 52(STATE)
+	lw	X14, 56(STATE)
+	lw	X15, 60(STATE)
+
+.Loop_hchacha_xor_rounds:
+	addiu	$a2, -2
+	AXR( 0, 1, 2, 3,  4, 5, 6, 7, 12,13,14,15, 16);
+	AXR( 8, 9,10,11, 12,13,14,15,  4, 5, 6, 7, 12);
+	AXR( 0, 1, 2, 3,  4, 5, 6, 7, 12,13,14,15,  8);
+	AXR( 8, 9,10,11, 12,13,14,15,  4, 5, 6, 7,  7);
+	AXR( 0, 1, 2, 3,  5, 6, 7, 4, 15,12,13,14, 16);
+	AXR(10,11, 8, 9, 15,12,13,14,  5, 6, 7, 4, 12);
+	AXR( 0, 1, 2, 3,  5, 6, 7, 4, 15,12,13,14,  8);
+	AXR(10,11, 8, 9, 15,12,13,14,  5, 6, 7, 4,  7);
+	bnez	$a2, .Loop_hchacha_xor_rounds
+
+	/* Restore used register */
+	lw	X11, 0($sp)
+
+	sw	X0,  0(OUT)
+	sw	X1,  4(OUT)
+	sw	X2,  8(OUT)
+	sw	X3,  12(OUT)
+	sw	X12, 16(OUT)
+	sw	X13, 20(OUT)
+	sw	X14, 24(OUT)
+	sw	X15, 28(OUT)
+
+	addiu	$sp, STACK_SIZE
+	jr	$ra
+.end hchacha_block_arch
+.set at
diff --git a/arch/mips/crypto/chacha-glue.c b/arch/mips/crypto/chacha-glue.c
new file mode 100644
index 000000000..d1fd23e6e
--- /dev/null
+++ b/arch/mips/crypto/chacha-glue.c
@@ -0,0 +1,152 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * MIPS accelerated ChaCha and XChaCha stream ciphers,
+ * including ChaCha20 (RFC7539)
+ *
+ * Copyright (C) 2019 Linaro, Ltd. <ard.biesheuvel@linaro.org>
+ */
+
+#include <asm/byteorder.h>
+#include <crypto/algapi.h>
+#include <crypto/internal/chacha.h>
+#include <crypto/internal/skcipher.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+
+asmlinkage void chacha_crypt_arch(u32 *state, u8 *dst, const u8 *src,
+				  unsigned int bytes, int nrounds);
+EXPORT_SYMBOL(chacha_crypt_arch);
+
+asmlinkage void hchacha_block_arch(const u32 *state, u32 *stream, int nrounds);
+EXPORT_SYMBOL(hchacha_block_arch);
+
+void chacha_init_arch(u32 *state, const u32 *key, const u8 *iv)
+{
+	chacha_init_generic(state, key, iv);
+}
+EXPORT_SYMBOL(chacha_init_arch);
+
+static int chacha_mips_stream_xor(struct skcipher_request *req,
+				  const struct chacha_ctx *ctx, const u8 *iv)
+{
+	struct skcipher_walk walk;
+	u32 state[16];
+	int err;
+
+	err = skcipher_walk_virt(&walk, req, false);
+
+	chacha_init_generic(state, ctx->key, iv);
+
+	while (walk.nbytes > 0) {
+		unsigned int nbytes = walk.nbytes;
+
+		if (nbytes < walk.total)
+			nbytes = round_down(nbytes, walk.stride);
+
+		chacha_crypt(state, walk.dst.virt.addr, walk.src.virt.addr,
+			     nbytes, ctx->nrounds);
+		err = skcipher_walk_done(&walk, walk.nbytes - nbytes);
+	}
+
+	return err;
+}
+
+static int chacha_mips(struct skcipher_request *req)
+{
+	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
+	struct chacha_ctx *ctx = crypto_skcipher_ctx(tfm);
+
+	return chacha_mips_stream_xor(req, ctx, req->iv);
+}
+
+static int xchacha_mips(struct skcipher_request *req)
+{
+	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
+	struct chacha_ctx *ctx = crypto_skcipher_ctx(tfm);
+	struct chacha_ctx subctx;
+	u32 state[16];
+	u8 real_iv[16];
+
+	chacha_init_generic(state, ctx->key, req->iv);
+
+	hchacha_block(state, subctx.key, ctx->nrounds);
+	subctx.nrounds = ctx->nrounds;
+
+	memcpy(&real_iv[0], req->iv + 24, 8);
+	memcpy(&real_iv[8], req->iv + 16, 8);
+	return chacha_mips_stream_xor(req, &subctx, real_iv);
+}
+
+static struct skcipher_alg algs[] = {
+	{
+		.base.cra_name		= "chacha20",
+		.base.cra_driver_name	= "chacha20-mips",
+		.base.cra_priority	= 200,
+		.base.cra_blocksize	= 1,
+		.base.cra_ctxsize	= sizeof(struct chacha_ctx),
+		.base.cra_module	= THIS_MODULE,
+
+		.min_keysize		= CHACHA_KEY_SIZE,
+		.max_keysize		= CHACHA_KEY_SIZE,
+		.ivsize			= CHACHA_IV_SIZE,
+		.chunksize		= CHACHA_BLOCK_SIZE,
+		.setkey			= chacha20_setkey,
+		.encrypt		= chacha_mips,
+		.decrypt		= chacha_mips,
+	}, {
+		.base.cra_name		= "xchacha20",
+		.base.cra_driver_name	= "xchacha20-mips",
+		.base.cra_priority	= 200,
+		.base.cra_blocksize	= 1,
+		.base.cra_ctxsize	= sizeof(struct chacha_ctx),
+		.base.cra_module	= THIS_MODULE,
+
+		.min_keysize		= CHACHA_KEY_SIZE,
+		.max_keysize		= CHACHA_KEY_SIZE,
+		.ivsize			= XCHACHA_IV_SIZE,
+		.chunksize		= CHACHA_BLOCK_SIZE,
+		.setkey			= chacha20_setkey,
+		.encrypt		= xchacha_mips,
+		.decrypt		= xchacha_mips,
+	}, {
+		.base.cra_name		= "xchacha12",
+		.base.cra_driver_name	= "xchacha12-mips",
+		.base.cra_priority	= 200,
+		.base.cra_blocksize	= 1,
+		.base.cra_ctxsize	= sizeof(struct chacha_ctx),
+		.base.cra_module	= THIS_MODULE,
+
+		.min_keysize		= CHACHA_KEY_SIZE,
+		.max_keysize		= CHACHA_KEY_SIZE,
+		.ivsize			= XCHACHA_IV_SIZE,
+		.chunksize		= CHACHA_BLOCK_SIZE,
+		.setkey			= chacha12_setkey,
+		.encrypt		= xchacha_mips,
+		.decrypt		= xchacha_mips,
+	}
+};
+
+static int __init chacha_simd_mod_init(void)
+{
+	return IS_REACHABLE(CONFIG_CRYPTO_SKCIPHER) ?
+		crypto_register_skciphers(algs, ARRAY_SIZE(algs)) : 0;
+}
+
+static void __exit chacha_simd_mod_fini(void)
+{
+	if (IS_REACHABLE(CONFIG_CRYPTO_SKCIPHER))
+		crypto_unregister_skciphers(algs, ARRAY_SIZE(algs));
+}
+
+module_init(chacha_simd_mod_init);
+module_exit(chacha_simd_mod_fini);
+
+MODULE_DESCRIPTION("ChaCha and XChaCha stream ciphers (MIPS accelerated)");
+MODULE_AUTHOR("Ard Biesheuvel <ard.biesheuvel@linaro.org>");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS_CRYPTO("chacha20");
+MODULE_ALIAS_CRYPTO("chacha20-mips");
+MODULE_ALIAS_CRYPTO("xchacha20");
+MODULE_ALIAS_CRYPTO("xchacha20-mips");
+MODULE_ALIAS_CRYPTO("xchacha12");
+MODULE_ALIAS_CRYPTO("xchacha12-mips");
diff --git a/arch/mips/crypto/crc32-mips.c b/arch/mips/crypto/crc32-mips.c
new file mode 100644
index 000000000..3e4f5ba10
--- /dev/null
+++ b/arch/mips/crypto/crc32-mips.c
@@ -0,0 +1,352 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * crc32-mips.c - CRC32 and CRC32C using optional MIPSr6 instructions
+ *
+ * Module based on arm64/crypto/crc32-arm.c
+ *
+ * Copyright (C) 2014 Linaro Ltd <yazen.ghannam@linaro.org>
+ * Copyright (C) 2018 MIPS Tech, LLC
+ */
+
+#include <linux/cpufeature.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/string.h>
+#include <asm/mipsregs.h>
+#include <asm/unaligned.h>
+
+#include <crypto/internal/hash.h>
+
+enum crc_op_size {
+	b, h, w, d,
+};
+
+enum crc_type {
+	crc32,
+	crc32c,
+};
+
+#ifndef TOOLCHAIN_SUPPORTS_CRC
+#define _ASM_SET_CRC(OP, SZ, TYPE)					  \
+_ASM_MACRO_3R(OP, rt, rs, rt2,						  \
+	".ifnc	\\rt, \\rt2\n\t"					  \
+	".error	\"invalid operands \\\"" #OP " \\rt,\\rs,\\rt2\\\"\"\n\t" \
+	".endif\n\t"							  \
+	_ASM_INSN_IF_MIPS(0x7c00000f | (__rt << 16) | (__rs << 21) |	  \
+			  ((SZ) <<  6) | ((TYPE) << 8))			  \
+	_ASM_INSN32_IF_MM(0x00000030 | (__rs << 16) | (__rt << 21) |	  \
+			  ((SZ) << 14) | ((TYPE) << 3)))
+#define _ASM_UNSET_CRC(op, SZ, TYPE) ".purgem " #op "\n\t"
+#else /* !TOOLCHAIN_SUPPORTS_CRC */
+#define _ASM_SET_CRC(op, SZ, TYPE) ".set\tcrc\n\t"
+#define _ASM_UNSET_CRC(op, SZ, TYPE)
+#endif
+
+#define __CRC32(crc, value, op, SZ, TYPE)		\
+do {							\
+	__asm__ __volatile__(				\
+		".set	push\n\t"			\
+		_ASM_SET_CRC(op, SZ, TYPE)		\
+		#op "	%0, %1, %0\n\t"			\
+		_ASM_UNSET_CRC(op, SZ, TYPE)		\
+		".set	pop"				\
+		: "+r" (crc)				\
+		: "r" (value));				\
+} while (0)
+
+#define _CRC32_crc32b(crc, value)	__CRC32(crc, value, crc32b, 0, 0)
+#define _CRC32_crc32h(crc, value)	__CRC32(crc, value, crc32h, 1, 0)
+#define _CRC32_crc32w(crc, value)	__CRC32(crc, value, crc32w, 2, 0)
+#define _CRC32_crc32d(crc, value)	__CRC32(crc, value, crc32d, 3, 0)
+#define _CRC32_crc32cb(crc, value)	__CRC32(crc, value, crc32cb, 0, 1)
+#define _CRC32_crc32ch(crc, value)	__CRC32(crc, value, crc32ch, 1, 1)
+#define _CRC32_crc32cw(crc, value)	__CRC32(crc, value, crc32cw, 2, 1)
+#define _CRC32_crc32cd(crc, value)	__CRC32(crc, value, crc32cd, 3, 1)
+
+#define _CRC32(crc, value, size, op) \
+	_CRC32_##op##size(crc, value)
+
+#define CRC32(crc, value, size) \
+	_CRC32(crc, value, size, crc32)
+
+#define CRC32C(crc, value, size) \
+	_CRC32(crc, value, size, crc32c)
+
+static u32 crc32_mips_le_hw(u32 crc_, const u8 *p, unsigned int len)
+{
+	u32 crc = crc_;
+
+#ifdef CONFIG_64BIT
+	while (len >= sizeof(u64)) {
+		u64 value = get_unaligned_le64(p);
+
+		CRC32(crc, value, d);
+		p += sizeof(u64);
+		len -= sizeof(u64);
+	}
+
+	if (len & sizeof(u32)) {
+#else /* !CONFIG_64BIT */
+	while (len >= sizeof(u32)) {
+#endif
+		u32 value = get_unaligned_le32(p);
+
+		CRC32(crc, value, w);
+		p += sizeof(u32);
+		len -= sizeof(u32);
+	}
+
+	if (len & sizeof(u16)) {
+		u16 value = get_unaligned_le16(p);
+
+		CRC32(crc, value, h);
+		p += sizeof(u16);
+	}
+
+	if (len & sizeof(u8)) {
+		u8 value = *p++;
+
+		CRC32(crc, value, b);
+	}
+
+	return crc;
+}
+
+static u32 crc32c_mips_le_hw(u32 crc_, const u8 *p, unsigned int len)
+{
+	u32 crc = crc_;
+
+#ifdef CONFIG_64BIT
+	while (len >= sizeof(u64)) {
+		u64 value = get_unaligned_le64(p);
+
+		CRC32C(crc, value, d);
+		p += sizeof(u64);
+		len -= sizeof(u64);
+	}
+
+	if (len & sizeof(u32)) {
+#else /* !CONFIG_64BIT */
+	while (len >= sizeof(u32)) {
+#endif
+		u32 value = get_unaligned_le32(p);
+
+		CRC32C(crc, value, w);
+		p += sizeof(u32);
+		len -= sizeof(u32);
+	}
+
+	if (len & sizeof(u16)) {
+		u16 value = get_unaligned_le16(p);
+
+		CRC32C(crc, value, h);
+		p += sizeof(u16);
+	}
+
+	if (len & sizeof(u8)) {
+		u8 value = *p++;
+
+		CRC32C(crc, value, b);
+	}
+	return crc;
+}
+
+#define CHKSUM_BLOCK_SIZE	1
+#define CHKSUM_DIGEST_SIZE	4
+
+struct chksum_ctx {
+	u32 key;
+};
+
+struct chksum_desc_ctx {
+	u32 crc;
+};
+
+static int chksum_init(struct shash_desc *desc)
+{
+	struct chksum_ctx *mctx = crypto_shash_ctx(desc->tfm);
+	struct chksum_desc_ctx *ctx = shash_desc_ctx(desc);
+
+	ctx->crc = mctx->key;
+
+	return 0;
+}
+
+/*
+ * Setting the seed allows arbitrary accumulators and flexible XOR policy
+ * If your algorithm starts with ~0, then XOR with ~0 before you set
+ * the seed.
+ */
+static int chksum_setkey(struct crypto_shash *tfm, const u8 *key,
+			 unsigned int keylen)
+{
+	struct chksum_ctx *mctx = crypto_shash_ctx(tfm);
+
+	if (keylen != sizeof(mctx->key))
+		return -EINVAL;
+	mctx->key = get_unaligned_le32(key);
+	return 0;
+}
+
+static int chksum_update(struct shash_desc *desc, const u8 *data,
+			 unsigned int length)
+{
+	struct chksum_desc_ctx *ctx = shash_desc_ctx(desc);
+
+	ctx->crc = crc32_mips_le_hw(ctx->crc, data, length);
+	return 0;
+}
+
+static int chksumc_update(struct shash_desc *desc, const u8 *data,
+			 unsigned int length)
+{
+	struct chksum_desc_ctx *ctx = shash_desc_ctx(desc);
+
+	ctx->crc = crc32c_mips_le_hw(ctx->crc, data, length);
+	return 0;
+}
+
+static int chksum_final(struct shash_desc *desc, u8 *out)
+{
+	struct chksum_desc_ctx *ctx = shash_desc_ctx(desc);
+
+	put_unaligned_le32(ctx->crc, out);
+	return 0;
+}
+
+static int chksumc_final(struct shash_desc *desc, u8 *out)
+{
+	struct chksum_desc_ctx *ctx = shash_desc_ctx(desc);
+
+	put_unaligned_le32(~ctx->crc, out);
+	return 0;
+}
+
+static int __chksum_finup(u32 crc, const u8 *data, unsigned int len, u8 *out)
+{
+	put_unaligned_le32(crc32_mips_le_hw(crc, data, len), out);
+	return 0;
+}
+
+static int __chksumc_finup(u32 crc, const u8 *data, unsigned int len, u8 *out)
+{
+	put_unaligned_le32(~crc32c_mips_le_hw(crc, data, len), out);
+	return 0;
+}
+
+static int chksum_finup(struct shash_desc *desc, const u8 *data,
+			unsigned int len, u8 *out)
+{
+	struct chksum_desc_ctx *ctx = shash_desc_ctx(desc);
+
+	return __chksum_finup(ctx->crc, data, len, out);
+}
+
+static int chksumc_finup(struct shash_desc *desc, const u8 *data,
+			unsigned int len, u8 *out)
+{
+	struct chksum_desc_ctx *ctx = shash_desc_ctx(desc);
+
+	return __chksumc_finup(ctx->crc, data, len, out);
+}
+
+static int chksum_digest(struct shash_desc *desc, const u8 *data,
+			 unsigned int length, u8 *out)
+{
+	struct chksum_ctx *mctx = crypto_shash_ctx(desc->tfm);
+
+	return __chksum_finup(mctx->key, data, length, out);
+}
+
+static int chksumc_digest(struct shash_desc *desc, const u8 *data,
+			 unsigned int length, u8 *out)
+{
+	struct chksum_ctx *mctx = crypto_shash_ctx(desc->tfm);
+
+	return __chksumc_finup(mctx->key, data, length, out);
+}
+
+static int chksum_cra_init(struct crypto_tfm *tfm)
+{
+	struct chksum_ctx *mctx = crypto_tfm_ctx(tfm);
+
+	mctx->key = ~0;
+	return 0;
+}
+
+static struct shash_alg crc32_alg = {
+	.digestsize		=	CHKSUM_DIGEST_SIZE,
+	.setkey			=	chksum_setkey,
+	.init			=	chksum_init,
+	.update			=	chksum_update,
+	.final			=	chksum_final,
+	.finup			=	chksum_finup,
+	.digest			=	chksum_digest,
+	.descsize		=	sizeof(struct chksum_desc_ctx),
+	.base			=	{
+		.cra_name		=	"crc32",
+		.cra_driver_name	=	"crc32-mips-hw",
+		.cra_priority		=	300,
+		.cra_flags		=	CRYPTO_ALG_OPTIONAL_KEY,
+		.cra_blocksize		=	CHKSUM_BLOCK_SIZE,
+		.cra_alignmask		=	0,
+		.cra_ctxsize		=	sizeof(struct chksum_ctx),
+		.cra_module		=	THIS_MODULE,
+		.cra_init		=	chksum_cra_init,
+	}
+};
+
+static struct shash_alg crc32c_alg = {
+	.digestsize		=	CHKSUM_DIGEST_SIZE,
+	.setkey			=	chksum_setkey,
+	.init			=	chksum_init,
+	.update			=	chksumc_update,
+	.final			=	chksumc_final,
+	.finup			=	chksumc_finup,
+	.digest			=	chksumc_digest,
+	.descsize		=	sizeof(struct chksum_desc_ctx),
+	.base			=	{
+		.cra_name		=	"crc32c",
+		.cra_driver_name	=	"crc32c-mips-hw",
+		.cra_priority		=	300,
+		.cra_flags		=	CRYPTO_ALG_OPTIONAL_KEY,
+		.cra_blocksize		=	CHKSUM_BLOCK_SIZE,
+		.cra_alignmask		=	0,
+		.cra_ctxsize		=	sizeof(struct chksum_ctx),
+		.cra_module		=	THIS_MODULE,
+		.cra_init		=	chksum_cra_init,
+	}
+};
+
+static int __init crc32_mod_init(void)
+{
+	int err;
+
+	err = crypto_register_shash(&crc32_alg);
+
+	if (err)
+		return err;
+
+	err = crypto_register_shash(&crc32c_alg);
+
+	if (err) {
+		crypto_unregister_shash(&crc32_alg);
+		return err;
+	}
+
+	return 0;
+}
+
+static void __exit crc32_mod_exit(void)
+{
+	crypto_unregister_shash(&crc32_alg);
+	crypto_unregister_shash(&crc32c_alg);
+}
+
+MODULE_AUTHOR("Marcin Nowakowski <marcin.nowakowski@mips.com");
+MODULE_DESCRIPTION("CRC32 and CRC32C using optional MIPS instructions");
+MODULE_LICENSE("GPL v2");
+
+module_cpu_feature_match(MIPS_CRC32, crc32_mod_init);
+module_exit(crc32_mod_exit);
diff --git a/arch/mips/crypto/poly1305-glue.c b/arch/mips/crypto/poly1305-glue.c
new file mode 100644
index 000000000..bc6110fb9
--- /dev/null
+++ b/arch/mips/crypto/poly1305-glue.c
@@ -0,0 +1,191 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * OpenSSL/Cryptogams accelerated Poly1305 transform for MIPS
+ *
+ * Copyright (C) 2019 Linaro Ltd. <ard.biesheuvel@linaro.org>
+ */
+
+#include <asm/unaligned.h>
+#include <crypto/algapi.h>
+#include <crypto/internal/hash.h>
+#include <crypto/internal/poly1305.h>
+#include <linux/cpufeature.h>
+#include <linux/crypto.h>
+#include <linux/module.h>
+
+asmlinkage void poly1305_init_mips(void *state, const u8 *key);
+asmlinkage void poly1305_blocks_mips(void *state, const u8 *src, u32 len, u32 hibit);
+asmlinkage void poly1305_emit_mips(void *state, u8 *digest, const u32 *nonce);
+
+void poly1305_init_arch(struct poly1305_desc_ctx *dctx, const u8 key[POLY1305_KEY_SIZE])
+{
+	poly1305_init_mips(&dctx->h, key);
+	dctx->s[0] = get_unaligned_le32(key + 16);
+	dctx->s[1] = get_unaligned_le32(key + 20);
+	dctx->s[2] = get_unaligned_le32(key + 24);
+	dctx->s[3] = get_unaligned_le32(key + 28);
+	dctx->buflen = 0;
+}
+EXPORT_SYMBOL(poly1305_init_arch);
+
+static int mips_poly1305_init(struct shash_desc *desc)
+{
+	struct poly1305_desc_ctx *dctx = shash_desc_ctx(desc);
+
+	dctx->buflen = 0;
+	dctx->rset = 0;
+	dctx->sset = false;
+
+	return 0;
+}
+
+static void mips_poly1305_blocks(struct poly1305_desc_ctx *dctx, const u8 *src,
+				 u32 len, u32 hibit)
+{
+	if (unlikely(!dctx->sset)) {
+		if (!dctx->rset) {
+			poly1305_init_mips(&dctx->h, src);
+			src += POLY1305_BLOCK_SIZE;
+			len -= POLY1305_BLOCK_SIZE;
+			dctx->rset = 1;
+		}
+		if (len >= POLY1305_BLOCK_SIZE) {
+			dctx->s[0] = get_unaligned_le32(src +  0);
+			dctx->s[1] = get_unaligned_le32(src +  4);
+			dctx->s[2] = get_unaligned_le32(src +  8);
+			dctx->s[3] = get_unaligned_le32(src + 12);
+			src += POLY1305_BLOCK_SIZE;
+			len -= POLY1305_BLOCK_SIZE;
+			dctx->sset = true;
+		}
+		if (len < POLY1305_BLOCK_SIZE)
+			return;
+	}
+
+	len &= ~(POLY1305_BLOCK_SIZE - 1);
+
+	poly1305_blocks_mips(&dctx->h, src, len, hibit);
+}
+
+static int mips_poly1305_update(struct shash_desc *desc, const u8 *src,
+				unsigned int len)
+{
+	struct poly1305_desc_ctx *dctx = shash_desc_ctx(desc);
+
+	if (unlikely(dctx->buflen)) {
+		u32 bytes = min(len, POLY1305_BLOCK_SIZE - dctx->buflen);
+
+		memcpy(dctx->buf + dctx->buflen, src, bytes);
+		src += bytes;
+		len -= bytes;
+		dctx->buflen += bytes;
+
+		if (dctx->buflen == POLY1305_BLOCK_SIZE) {
+			mips_poly1305_blocks(dctx, dctx->buf, POLY1305_BLOCK_SIZE, 1);
+			dctx->buflen = 0;
+		}
+	}
+
+	if (likely(len >= POLY1305_BLOCK_SIZE)) {
+		mips_poly1305_blocks(dctx, src, len, 1);
+		src += round_down(len, POLY1305_BLOCK_SIZE);
+		len %= POLY1305_BLOCK_SIZE;
+	}
+
+	if (unlikely(len)) {
+		dctx->buflen = len;
+		memcpy(dctx->buf, src, len);
+	}
+	return 0;
+}
+
+void poly1305_update_arch(struct poly1305_desc_ctx *dctx, const u8 *src,
+			  unsigned int nbytes)
+{
+	if (unlikely(dctx->buflen)) {
+		u32 bytes = min(nbytes, POLY1305_BLOCK_SIZE - dctx->buflen);
+
+		memcpy(dctx->buf + dctx->buflen, src, bytes);
+		src += bytes;
+		nbytes -= bytes;
+		dctx->buflen += bytes;
+
+		if (dctx->buflen == POLY1305_BLOCK_SIZE) {
+			poly1305_blocks_mips(&dctx->h, dctx->buf,
+					     POLY1305_BLOCK_SIZE, 1);
+			dctx->buflen = 0;
+		}
+	}
+
+	if (likely(nbytes >= POLY1305_BLOCK_SIZE)) {
+		unsigned int len = round_down(nbytes, POLY1305_BLOCK_SIZE);
+
+		poly1305_blocks_mips(&dctx->h, src, len, 1);
+		src += len;
+		nbytes %= POLY1305_BLOCK_SIZE;
+	}
+
+	if (unlikely(nbytes)) {
+		dctx->buflen = nbytes;
+		memcpy(dctx->buf, src, nbytes);
+	}
+}
+EXPORT_SYMBOL(poly1305_update_arch);
+
+void poly1305_final_arch(struct poly1305_desc_ctx *dctx, u8 *dst)
+{
+	if (unlikely(dctx->buflen)) {
+		dctx->buf[dctx->buflen++] = 1;
+		memset(dctx->buf + dctx->buflen, 0,
+		       POLY1305_BLOCK_SIZE - dctx->buflen);
+		poly1305_blocks_mips(&dctx->h, dctx->buf, POLY1305_BLOCK_SIZE, 0);
+	}
+
+	poly1305_emit_mips(&dctx->h, dst, dctx->s);
+	*dctx = (struct poly1305_desc_ctx){};
+}
+EXPORT_SYMBOL(poly1305_final_arch);
+
+static int mips_poly1305_final(struct shash_desc *desc, u8 *dst)
+{
+	struct poly1305_desc_ctx *dctx = shash_desc_ctx(desc);
+
+	if (unlikely(!dctx->sset))
+		return -ENOKEY;
+
+	poly1305_final_arch(dctx, dst);
+	return 0;
+}
+
+static struct shash_alg mips_poly1305_alg = {
+	.init			= mips_poly1305_init,
+	.update			= mips_poly1305_update,
+	.final			= mips_poly1305_final,
+	.digestsize		= POLY1305_DIGEST_SIZE,
+	.descsize		= sizeof(struct poly1305_desc_ctx),
+
+	.base.cra_name		= "poly1305",
+	.base.cra_driver_name	= "poly1305-mips",
+	.base.cra_priority	= 200,
+	.base.cra_blocksize	= POLY1305_BLOCK_SIZE,
+	.base.cra_module	= THIS_MODULE,
+};
+
+static int __init mips_poly1305_mod_init(void)
+{
+	return IS_REACHABLE(CONFIG_CRYPTO_HASH) ?
+		crypto_register_shash(&mips_poly1305_alg) : 0;
+}
+
+static void __exit mips_poly1305_mod_exit(void)
+{
+	if (IS_REACHABLE(CONFIG_CRYPTO_HASH))
+		crypto_unregister_shash(&mips_poly1305_alg);
+}
+
+module_init(mips_poly1305_mod_init);
+module_exit(mips_poly1305_mod_exit);
+
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS_CRYPTO("poly1305");
+MODULE_ALIAS_CRYPTO("poly1305-mips");
diff --git a/arch/mips/crypto/poly1305-mips.pl b/arch/mips/crypto/poly1305-mips.pl
new file mode 100644
index 000000000..b05bab884
--- /dev/null
+++ b/arch/mips/crypto/poly1305-mips.pl
@@ -0,0 +1,1273 @@
+#!/usr/bin/env perl
+# SPDX-License-Identifier: GPL-1.0+ OR BSD-3-Clause
+#
+# ====================================================================
+# Written by Andy Polyakov, @dot-asm, originally for the OpenSSL
+# project.
+# ====================================================================
+
+# Poly1305 hash for MIPS.
+#
+# May 2016
+#
+# Numbers are cycles per processed byte with poly1305_blocks alone.
+#
+#		IALU/gcc
+# R1x000	~5.5/+130%	(big-endian)
+# Octeon II	2.50/+70%	(little-endian)
+#
+# March 2019
+#
+# Add 32-bit code path.
+#
+# October 2019
+#
+# Modulo-scheduling reduction allows to omit dependency chain at the
+# end of inner loop and improve performance. Also optimize MIPS32R2
+# code path for MIPS 1004K core. Per René von Dorst's suggestions.
+#
+#		IALU/gcc
+# R1x000	~9.8/?		(big-endian)
+# Octeon II	3.65/+140%	(little-endian)
+# MT7621/1004K	4.75/?		(little-endian)
+#
+######################################################################
+# There is a number of MIPS ABI in use, O32 and N32/64 are most
+# widely used. Then there is a new contender: NUBI. It appears that if
+# one picks the latter, it's possible to arrange code in ABI neutral
+# manner. Therefore let's stick to NUBI register layout:
+#
+($zero,$at,$t0,$t1,$t2)=map("\$$_",(0..2,24,25));
+($a0,$a1,$a2,$a3,$a4,$a5,$a6,$a7)=map("\$$_",(4..11));
+($s0,$s1,$s2,$s3,$s4,$s5,$s6,$s7,$s8,$s9,$s10,$s11)=map("\$$_",(12..23));
+($gp,$tp,$sp,$fp,$ra)=map("\$$_",(3,28..31));
+#
+# The return value is placed in $a0. Following coding rules facilitate
+# interoperability:
+#
+# - never ever touch $tp, "thread pointer", former $gp [o32 can be
+#   excluded from the rule, because it's specified volatile];
+# - copy return value to $t0, former $v0 [or to $a0 if you're adapting
+#   old code];
+# - on O32 populate $a4-$a7 with 'lw $aN,4*N($sp)' if necessary;
+#
+# For reference here is register layout for N32/64 MIPS ABIs:
+#
+# ($zero,$at,$v0,$v1)=map("\$$_",(0..3));
+# ($a0,$a1,$a2,$a3,$a4,$a5,$a6,$a7)=map("\$$_",(4..11));
+# ($t0,$t1,$t2,$t3,$t8,$t9)=map("\$$_",(12..15,24,25));
+# ($s0,$s1,$s2,$s3,$s4,$s5,$s6,$s7)=map("\$$_",(16..23));
+# ($gp,$sp,$fp,$ra)=map("\$$_",(28..31));
+#
+# <appro@openssl.org>
+#
+######################################################################
+
+$flavour = shift || "64"; # supported flavours are o32,n32,64,nubi32,nubi64
+
+$v0 = ($flavour =~ /nubi/i) ? $a0 : $t0;
+
+if ($flavour =~ /64|n32/i) {{{
+######################################################################
+# 64-bit code path
+#
+
+my ($ctx,$inp,$len,$padbit) = ($a0,$a1,$a2,$a3);
+my ($in0,$in1,$tmp0,$tmp1,$tmp2,$tmp3,$tmp4) = ($a4,$a5,$a6,$a7,$at,$t0,$t1);
+
+$code.=<<___;
+#if (defined(_MIPS_ARCH_MIPS64R3) || defined(_MIPS_ARCH_MIPS64R5) || \\
+     defined(_MIPS_ARCH_MIPS64R6)) \\
+     && !defined(_MIPS_ARCH_MIPS64R2)
+# define _MIPS_ARCH_MIPS64R2
+#endif
+
+#if defined(_MIPS_ARCH_MIPS64R6)
+# define dmultu(rs,rt)
+# define mflo(rd,rs,rt)	dmulu	rd,rs,rt
+# define mfhi(rd,rs,rt)	dmuhu	rd,rs,rt
+#else
+# define dmultu(rs,rt)		dmultu	rs,rt
+# define mflo(rd,rs,rt)	mflo	rd
+# define mfhi(rd,rs,rt)	mfhi	rd
+#endif
+
+#ifdef	__KERNEL__
+# define poly1305_init   poly1305_init_mips
+# define poly1305_blocks poly1305_blocks_mips
+# define poly1305_emit   poly1305_emit_mips
+#endif
+
+#if defined(__MIPSEB__) && !defined(MIPSEB)
+# define MIPSEB
+#endif
+
+#ifdef MIPSEB
+# define MSB 0
+# define LSB 7
+#else
+# define MSB 7
+# define LSB 0
+#endif
+
+.text
+.set	noat
+.set	noreorder
+
+.align	5
+.globl	poly1305_init
+.ent	poly1305_init
+poly1305_init:
+	.frame	$sp,0,$ra
+	.set	reorder
+
+	sd	$zero,0($ctx)
+	sd	$zero,8($ctx)
+	sd	$zero,16($ctx)
+
+	beqz	$inp,.Lno_key
+
+#if defined(_MIPS_ARCH_MIPS64R6)
+	andi	$tmp0,$inp,7		# $inp % 8
+	dsubu	$inp,$inp,$tmp0		# align $inp
+	sll	$tmp0,$tmp0,3		# byte to bit offset
+	ld	$in0,0($inp)
+	ld	$in1,8($inp)
+	beqz	$tmp0,.Laligned_key
+	ld	$tmp2,16($inp)
+
+	subu	$tmp1,$zero,$tmp0
+# ifdef	MIPSEB
+	dsllv	$in0,$in0,$tmp0
+	dsrlv	$tmp3,$in1,$tmp1
+	dsllv	$in1,$in1,$tmp0
+	dsrlv	$tmp2,$tmp2,$tmp1
+# else
+	dsrlv	$in0,$in0,$tmp0
+	dsllv	$tmp3,$in1,$tmp1
+	dsrlv	$in1,$in1,$tmp0
+	dsllv	$tmp2,$tmp2,$tmp1
+# endif
+	or	$in0,$in0,$tmp3
+	or	$in1,$in1,$tmp2
+.Laligned_key:
+#else
+	ldl	$in0,0+MSB($inp)
+	ldl	$in1,8+MSB($inp)
+	ldr	$in0,0+LSB($inp)
+	ldr	$in1,8+LSB($inp)
+#endif
+#ifdef	MIPSEB
+# if defined(_MIPS_ARCH_MIPS64R2)
+	dsbh	$in0,$in0		# byte swap
+	 dsbh	$in1,$in1
+	dshd	$in0,$in0
+	 dshd	$in1,$in1
+# else
+	ori	$tmp0,$zero,0xFF
+	dsll	$tmp2,$tmp0,32
+	or	$tmp0,$tmp2		# 0x000000FF000000FF
+
+	and	$tmp1,$in0,$tmp0	# byte swap
+	 and	$tmp3,$in1,$tmp0
+	dsrl	$tmp2,$in0,24
+	 dsrl	$tmp4,$in1,24
+	dsll	$tmp1,24
+	 dsll	$tmp3,24
+	and	$tmp2,$tmp0
+	 and	$tmp4,$tmp0
+	dsll	$tmp0,8			# 0x0000FF000000FF00
+	or	$tmp1,$tmp2
+	 or	$tmp3,$tmp4
+	and	$tmp2,$in0,$tmp0
+	 and	$tmp4,$in1,$tmp0
+	dsrl	$in0,8
+	 dsrl	$in1,8
+	dsll	$tmp2,8
+	 dsll	$tmp4,8
+	and	$in0,$tmp0
+	 and	$in1,$tmp0
+	or	$tmp1,$tmp2
+	 or	$tmp3,$tmp4
+	or	$in0,$tmp1
+	 or	$in1,$tmp3
+	dsrl	$tmp1,$in0,32
+	 dsrl	$tmp3,$in1,32
+	dsll	$in0,32
+	 dsll	$in1,32
+	or	$in0,$tmp1
+	 or	$in1,$tmp3
+# endif
+#endif
+	li	$tmp0,1
+	dsll	$tmp0,32		# 0x0000000100000000
+	daddiu	$tmp0,-63		# 0x00000000ffffffc1
+	dsll	$tmp0,28		# 0x0ffffffc10000000
+	daddiu	$tmp0,-1		# 0x0ffffffc0fffffff
+
+	and	$in0,$tmp0
+	daddiu	$tmp0,-3		# 0x0ffffffc0ffffffc
+	and	$in1,$tmp0
+
+	sd	$in0,24($ctx)
+	dsrl	$tmp0,$in1,2
+	sd	$in1,32($ctx)
+	daddu	$tmp0,$in1		# s1 = r1 + (r1 >> 2)
+	sd	$tmp0,40($ctx)
+
+.Lno_key:
+	li	$v0,0			# return 0
+	jr	$ra
+.end	poly1305_init
+___
+{
+my $SAVED_REGS_MASK = ($flavour =~ /nubi/i) ? "0x0003f000" : "0x00030000";
+
+my ($h0,$h1,$h2,$r0,$r1,$rs1,$d0,$d1,$d2) =
+   ($s0,$s1,$s2,$s3,$s4,$s5,$in0,$in1,$t2);
+my ($shr,$shl) = ($s6,$s7);		# used on R6
+
+$code.=<<___;
+.align	5
+.globl	poly1305_blocks
+.ent	poly1305_blocks
+poly1305_blocks:
+	.set	noreorder
+	dsrl	$len,4			# number of complete blocks
+	bnez	$len,poly1305_blocks_internal
+	nop
+	jr	$ra
+	nop
+.end	poly1305_blocks
+
+.align	5
+.ent	poly1305_blocks_internal
+poly1305_blocks_internal:
+	.set	noreorder
+#if defined(_MIPS_ARCH_MIPS64R6)
+	.frame	$sp,8*8,$ra
+	.mask	$SAVED_REGS_MASK|0x000c0000,-8
+	dsubu	$sp,8*8
+	sd	$s7,56($sp)
+	sd	$s6,48($sp)
+#else
+	.frame	$sp,6*8,$ra
+	.mask	$SAVED_REGS_MASK,-8
+	dsubu	$sp,6*8
+#endif
+	sd	$s5,40($sp)
+	sd	$s4,32($sp)
+___
+$code.=<<___ if ($flavour =~ /nubi/i);	# optimize non-nubi prologue
+	sd	$s3,24($sp)
+	sd	$s2,16($sp)
+	sd	$s1,8($sp)
+	sd	$s0,0($sp)
+___
+$code.=<<___;
+	.set	reorder
+
+#if defined(_MIPS_ARCH_MIPS64R6)
+	andi	$shr,$inp,7
+	dsubu	$inp,$inp,$shr		# align $inp
+	sll	$shr,$shr,3		# byte to bit offset
+	subu	$shl,$zero,$shr
+#endif
+
+	ld	$h0,0($ctx)		# load hash value
+	ld	$h1,8($ctx)
+	ld	$h2,16($ctx)
+
+	ld	$r0,24($ctx)		# load key
+	ld	$r1,32($ctx)
+	ld	$rs1,40($ctx)
+
+	dsll	$len,4
+	daddu	$len,$inp		# end of buffer
+	b	.Loop
+
+.align	4
+.Loop:
+#if defined(_MIPS_ARCH_MIPS64R6)
+	ld	$in0,0($inp)		# load input
+	ld	$in1,8($inp)
+	beqz	$shr,.Laligned_inp
+
+	ld	$tmp2,16($inp)
+# ifdef	MIPSEB
+	dsllv	$in0,$in0,$shr
+	dsrlv	$tmp3,$in1,$shl
+	dsllv	$in1,$in1,$shr
+	dsrlv	$tmp2,$tmp2,$shl
+# else
+	dsrlv	$in0,$in0,$shr
+	dsllv	$tmp3,$in1,$shl
+	dsrlv	$in1,$in1,$shr
+	dsllv	$tmp2,$tmp2,$shl
+# endif
+	or	$in0,$in0,$tmp3
+	or	$in1,$in1,$tmp2
+.Laligned_inp:
+#else
+	ldl	$in0,0+MSB($inp)	# load input
+	ldl	$in1,8+MSB($inp)
+	ldr	$in0,0+LSB($inp)
+	ldr	$in1,8+LSB($inp)
+#endif
+	daddiu	$inp,16
+#ifdef	MIPSEB
+# if defined(_MIPS_ARCH_MIPS64R2)
+	dsbh	$in0,$in0		# byte swap
+	 dsbh	$in1,$in1
+	dshd	$in0,$in0
+	 dshd	$in1,$in1
+# else
+	ori	$tmp0,$zero,0xFF
+	dsll	$tmp2,$tmp0,32
+	or	$tmp0,$tmp2		# 0x000000FF000000FF
+
+	and	$tmp1,$in0,$tmp0	# byte swap
+	 and	$tmp3,$in1,$tmp0
+	dsrl	$tmp2,$in0,24
+	 dsrl	$tmp4,$in1,24
+	dsll	$tmp1,24
+	 dsll	$tmp3,24
+	and	$tmp2,$tmp0
+	 and	$tmp4,$tmp0
+	dsll	$tmp0,8			# 0x0000FF000000FF00
+	or	$tmp1,$tmp2
+	 or	$tmp3,$tmp4
+	and	$tmp2,$in0,$tmp0
+	 and	$tmp4,$in1,$tmp0
+	dsrl	$in0,8
+	 dsrl	$in1,8
+	dsll	$tmp2,8
+	 dsll	$tmp4,8
+	and	$in0,$tmp0
+	 and	$in1,$tmp0
+	or	$tmp1,$tmp2
+	 or	$tmp3,$tmp4
+	or	$in0,$tmp1
+	 or	$in1,$tmp3
+	dsrl	$tmp1,$in0,32
+	 dsrl	$tmp3,$in1,32
+	dsll	$in0,32
+	 dsll	$in1,32
+	or	$in0,$tmp1
+	 or	$in1,$tmp3
+# endif
+#endif
+	dsrl	$tmp1,$h2,2		# modulo-scheduled reduction
+	andi	$h2,$h2,3
+	dsll	$tmp0,$tmp1,2
+
+	daddu	$d0,$h0,$in0		# accumulate input
+	 daddu	$tmp1,$tmp0
+	sltu	$tmp0,$d0,$h0
+	daddu	$d0,$d0,$tmp1		# ... and residue
+	sltu	$tmp1,$d0,$tmp1
+	daddu	$d1,$h1,$in1
+	daddu	$tmp0,$tmp1
+	sltu	$tmp1,$d1,$h1
+	daddu	$d1,$tmp0
+
+	dmultu	($r0,$d0)		# h0*r0
+	 daddu	$d2,$h2,$padbit
+	 sltu	$tmp0,$d1,$tmp0
+	mflo	($h0,$r0,$d0)
+	mfhi	($h1,$r0,$d0)
+
+	dmultu	($rs1,$d1)		# h1*5*r1
+	 daddu	$d2,$tmp1
+	 daddu	$d2,$tmp0
+	mflo	($tmp0,$rs1,$d1)
+	mfhi	($tmp1,$rs1,$d1)
+
+	dmultu	($r1,$d0)		# h0*r1
+	mflo	($tmp2,$r1,$d0)
+	mfhi	($h2,$r1,$d0)
+	 daddu	$h0,$tmp0
+	 daddu	$h1,$tmp1
+	 sltu	$tmp0,$h0,$tmp0
+
+	dmultu	($r0,$d1)		# h1*r0
+	 daddu	$h1,$tmp0
+	 daddu	$h1,$tmp2
+	mflo	($tmp0,$r0,$d1)
+	mfhi	($tmp1,$r0,$d1)
+
+	dmultu	($rs1,$d2)		# h2*5*r1
+	 sltu	$tmp2,$h1,$tmp2
+	 daddu	$h2,$tmp2
+	mflo	($tmp2,$rs1,$d2)
+
+	dmultu	($r0,$d2)		# h2*r0
+	 daddu	$h1,$tmp0
+	 daddu	$h2,$tmp1
+	mflo	($tmp3,$r0,$d2)
+	 sltu	$tmp0,$h1,$tmp0
+	 daddu	$h2,$tmp0
+
+	daddu	$h1,$tmp2
+	sltu	$tmp2,$h1,$tmp2
+	daddu	$h2,$tmp2
+	daddu	$h2,$tmp3
+
+	bne	$inp,$len,.Loop
+
+	sd	$h0,0($ctx)		# store hash value
+	sd	$h1,8($ctx)
+	sd	$h2,16($ctx)
+
+	.set	noreorder
+#if defined(_MIPS_ARCH_MIPS64R6)
+	ld	$s7,56($sp)
+	ld	$s6,48($sp)
+#endif
+	ld	$s5,40($sp)		# epilogue
+	ld	$s4,32($sp)
+___
+$code.=<<___ if ($flavour =~ /nubi/i);	# optimize non-nubi epilogue
+	ld	$s3,24($sp)
+	ld	$s2,16($sp)
+	ld	$s1,8($sp)
+	ld	$s0,0($sp)
+___
+$code.=<<___;
+	jr	$ra
+#if defined(_MIPS_ARCH_MIPS64R6)
+	daddu	$sp,8*8
+#else
+	daddu	$sp,6*8
+#endif
+.end	poly1305_blocks_internal
+___
+}
+{
+my ($ctx,$mac,$nonce) = ($a0,$a1,$a2);
+
+$code.=<<___;
+.align	5
+.globl	poly1305_emit
+.ent	poly1305_emit
+poly1305_emit:
+	.frame	$sp,0,$ra
+	.set	reorder
+
+	ld	$tmp2,16($ctx)
+	ld	$tmp0,0($ctx)
+	ld	$tmp1,8($ctx)
+
+	li	$in0,-4			# final reduction
+	dsrl	$in1,$tmp2,2
+	and	$in0,$tmp2
+	andi	$tmp2,$tmp2,3
+	daddu	$in0,$in1
+
+	daddu	$tmp0,$tmp0,$in0
+	sltu	$in1,$tmp0,$in0
+	 daddiu	$in0,$tmp0,5		# compare to modulus
+	daddu	$tmp1,$tmp1,$in1
+	 sltiu	$tmp3,$in0,5
+	sltu	$tmp4,$tmp1,$in1
+	 daddu	$in1,$tmp1,$tmp3
+	daddu	$tmp2,$tmp2,$tmp4
+	 sltu	$tmp3,$in1,$tmp3
+	 daddu	$tmp2,$tmp2,$tmp3
+
+	dsrl	$tmp2,2			# see if it carried/borrowed
+	dsubu	$tmp2,$zero,$tmp2
+
+	xor	$in0,$tmp0
+	xor	$in1,$tmp1
+	and	$in0,$tmp2
+	and	$in1,$tmp2
+	xor	$in0,$tmp0
+	xor	$in1,$tmp1
+
+	lwu	$tmp0,0($nonce)		# load nonce
+	lwu	$tmp1,4($nonce)
+	lwu	$tmp2,8($nonce)
+	lwu	$tmp3,12($nonce)
+	dsll	$tmp1,32
+	dsll	$tmp3,32
+	or	$tmp0,$tmp1
+	or	$tmp2,$tmp3
+
+	daddu	$in0,$tmp0		# accumulate nonce
+	daddu	$in1,$tmp2
+	sltu	$tmp0,$in0,$tmp0
+	daddu	$in1,$tmp0
+
+	dsrl	$tmp0,$in0,8		# write mac value
+	dsrl	$tmp1,$in0,16
+	dsrl	$tmp2,$in0,24
+	sb	$in0,0($mac)
+	dsrl	$tmp3,$in0,32
+	sb	$tmp0,1($mac)
+	dsrl	$tmp0,$in0,40
+	sb	$tmp1,2($mac)
+	dsrl	$tmp1,$in0,48
+	sb	$tmp2,3($mac)
+	dsrl	$tmp2,$in0,56
+	sb	$tmp3,4($mac)
+	dsrl	$tmp3,$in1,8
+	sb	$tmp0,5($mac)
+	dsrl	$tmp0,$in1,16
+	sb	$tmp1,6($mac)
+	dsrl	$tmp1,$in1,24
+	sb	$tmp2,7($mac)
+
+	sb	$in1,8($mac)
+	dsrl	$tmp2,$in1,32
+	sb	$tmp3,9($mac)
+	dsrl	$tmp3,$in1,40
+	sb	$tmp0,10($mac)
+	dsrl	$tmp0,$in1,48
+	sb	$tmp1,11($mac)
+	dsrl	$tmp1,$in1,56
+	sb	$tmp2,12($mac)
+	sb	$tmp3,13($mac)
+	sb	$tmp0,14($mac)
+	sb	$tmp1,15($mac)
+
+	jr	$ra
+.end	poly1305_emit
+.rdata
+.asciiz	"Poly1305 for MIPS64, CRYPTOGAMS by \@dot-asm"
+.align	2
+___
+}
+}}} else {{{
+######################################################################
+# 32-bit code path
+#
+
+my ($ctx,$inp,$len,$padbit) = ($a0,$a1,$a2,$a3);
+my ($in0,$in1,$in2,$in3,$tmp0,$tmp1,$tmp2,$tmp3) =
+   ($a4,$a5,$a6,$a7,$at,$t0,$t1,$t2);
+
+$code.=<<___;
+#if (defined(_MIPS_ARCH_MIPS32R3) || defined(_MIPS_ARCH_MIPS32R5) || \\
+     defined(_MIPS_ARCH_MIPS32R6)) \\
+     && !defined(_MIPS_ARCH_MIPS32R2)
+# define _MIPS_ARCH_MIPS32R2
+#endif
+
+#if defined(_MIPS_ARCH_MIPS32R6)
+# define multu(rs,rt)
+# define mflo(rd,rs,rt)	mulu	rd,rs,rt
+# define mfhi(rd,rs,rt)	muhu	rd,rs,rt
+#else
+# define multu(rs,rt)	multu	rs,rt
+# define mflo(rd,rs,rt)	mflo	rd
+# define mfhi(rd,rs,rt)	mfhi	rd
+#endif
+
+#ifdef	__KERNEL__
+# define poly1305_init   poly1305_init_mips
+# define poly1305_blocks poly1305_blocks_mips
+# define poly1305_emit   poly1305_emit_mips
+#endif
+
+#if defined(__MIPSEB__) && !defined(MIPSEB)
+# define MIPSEB
+#endif
+
+#ifdef MIPSEB
+# define MSB 0
+# define LSB 3
+#else
+# define MSB 3
+# define LSB 0
+#endif
+
+.text
+.set	noat
+.set	noreorder
+
+.align	5
+.globl	poly1305_init
+.ent	poly1305_init
+poly1305_init:
+	.frame	$sp,0,$ra
+	.set	reorder
+
+	sw	$zero,0($ctx)
+	sw	$zero,4($ctx)
+	sw	$zero,8($ctx)
+	sw	$zero,12($ctx)
+	sw	$zero,16($ctx)
+
+	beqz	$inp,.Lno_key
+
+#if defined(_MIPS_ARCH_MIPS32R6)
+	andi	$tmp0,$inp,3		# $inp % 4
+	subu	$inp,$inp,$tmp0		# align $inp
+	sll	$tmp0,$tmp0,3		# byte to bit offset
+	lw	$in0,0($inp)
+	lw	$in1,4($inp)
+	lw	$in2,8($inp)
+	lw	$in3,12($inp)
+	beqz	$tmp0,.Laligned_key
+
+	lw	$tmp2,16($inp)
+	subu	$tmp1,$zero,$tmp0
+# ifdef	MIPSEB
+	sllv	$in0,$in0,$tmp0
+	srlv	$tmp3,$in1,$tmp1
+	sllv	$in1,$in1,$tmp0
+	or	$in0,$in0,$tmp3
+	srlv	$tmp3,$in2,$tmp1
+	sllv	$in2,$in2,$tmp0
+	or	$in1,$in1,$tmp3
+	srlv	$tmp3,$in3,$tmp1
+	sllv	$in3,$in3,$tmp0
+	or	$in2,$in2,$tmp3
+	srlv	$tmp2,$tmp2,$tmp1
+	or	$in3,$in3,$tmp2
+# else
+	srlv	$in0,$in0,$tmp0
+	sllv	$tmp3,$in1,$tmp1
+	srlv	$in1,$in1,$tmp0
+	or	$in0,$in0,$tmp3
+	sllv	$tmp3,$in2,$tmp1
+	srlv	$in2,$in2,$tmp0
+	or	$in1,$in1,$tmp3
+	sllv	$tmp3,$in3,$tmp1
+	srlv	$in3,$in3,$tmp0
+	or	$in2,$in2,$tmp3
+	sllv	$tmp2,$tmp2,$tmp1
+	or	$in3,$in3,$tmp2
+# endif
+.Laligned_key:
+#else
+	lwl	$in0,0+MSB($inp)
+	lwl	$in1,4+MSB($inp)
+	lwl	$in2,8+MSB($inp)
+	lwl	$in3,12+MSB($inp)
+	lwr	$in0,0+LSB($inp)
+	lwr	$in1,4+LSB($inp)
+	lwr	$in2,8+LSB($inp)
+	lwr	$in3,12+LSB($inp)
+#endif
+#ifdef	MIPSEB
+# if defined(_MIPS_ARCH_MIPS32R2)
+	wsbh	$in0,$in0		# byte swap
+	wsbh	$in1,$in1
+	wsbh	$in2,$in2
+	wsbh	$in3,$in3
+	rotr	$in0,$in0,16
+	rotr	$in1,$in1,16
+	rotr	$in2,$in2,16
+	rotr	$in3,$in3,16
+# else
+	srl	$tmp0,$in0,24		# byte swap
+	srl	$tmp1,$in0,8
+	andi	$tmp2,$in0,0xFF00
+	sll	$in0,$in0,24
+	andi	$tmp1,0xFF00
+	sll	$tmp2,$tmp2,8
+	or	$in0,$tmp0
+	 srl	$tmp0,$in1,24
+	or	$tmp1,$tmp2
+	 srl	$tmp2,$in1,8
+	or	$in0,$tmp1
+	 andi	$tmp1,$in1,0xFF00
+	 sll	$in1,$in1,24
+	 andi	$tmp2,0xFF00
+	 sll	$tmp1,$tmp1,8
+	 or	$in1,$tmp0
+	srl	$tmp0,$in2,24
+	 or	$tmp2,$tmp1
+	srl	$tmp1,$in2,8
+	 or	$in1,$tmp2
+	andi	$tmp2,$in2,0xFF00
+	sll	$in2,$in2,24
+	andi	$tmp1,0xFF00
+	sll	$tmp2,$tmp2,8
+	or	$in2,$tmp0
+	 srl	$tmp0,$in3,24
+	or	$tmp1,$tmp2
+	 srl	$tmp2,$in3,8
+	or	$in2,$tmp1
+	 andi	$tmp1,$in3,0xFF00
+	 sll	$in3,$in3,24
+	 andi	$tmp2,0xFF00
+	 sll	$tmp1,$tmp1,8
+	 or	$in3,$tmp0
+	 or	$tmp2,$tmp1
+	 or	$in3,$tmp2
+# endif
+#endif
+	lui	$tmp0,0x0fff
+	ori	$tmp0,0xffff		# 0x0fffffff
+	and	$in0,$in0,$tmp0
+	subu	$tmp0,3			# 0x0ffffffc
+	and	$in1,$in1,$tmp0
+	and	$in2,$in2,$tmp0
+	and	$in3,$in3,$tmp0
+
+	sw	$in0,20($ctx)
+	sw	$in1,24($ctx)
+	sw	$in2,28($ctx)
+	sw	$in3,32($ctx)
+
+	srl	$tmp1,$in1,2
+	srl	$tmp2,$in2,2
+	srl	$tmp3,$in3,2
+	addu	$in1,$in1,$tmp1		# s1 = r1 + (r1 >> 2)
+	addu	$in2,$in2,$tmp2
+	addu	$in3,$in3,$tmp3
+	sw	$in1,36($ctx)
+	sw	$in2,40($ctx)
+	sw	$in3,44($ctx)
+.Lno_key:
+	li	$v0,0
+	jr	$ra
+.end	poly1305_init
+___
+{
+my $SAVED_REGS_MASK = ($flavour =~ /nubi/i) ? "0x00fff000" : "0x00ff0000";
+
+my ($h0,$h1,$h2,$h3,$h4, $r0,$r1,$r2,$r3, $rs1,$rs2,$rs3) =
+   ($s0,$s1,$s2,$s3,$s4, $s5,$s6,$s7,$s8, $s9,$s10,$s11);
+my ($d0,$d1,$d2,$d3) =
+   ($a4,$a5,$a6,$a7);
+my $shr = $t2;		# used on R6
+my $one = $t2;		# used on R2
+
+$code.=<<___;
+.globl	poly1305_blocks
+.align	5
+.ent	poly1305_blocks
+poly1305_blocks:
+	.frame	$sp,16*4,$ra
+	.mask	$SAVED_REGS_MASK,-4
+	.set	noreorder
+	subu	$sp, $sp,4*12
+	sw	$s11,4*11($sp)
+	sw	$s10,4*10($sp)
+	sw	$s9, 4*9($sp)
+	sw	$s8, 4*8($sp)
+	sw	$s7, 4*7($sp)
+	sw	$s6, 4*6($sp)
+	sw	$s5, 4*5($sp)
+	sw	$s4, 4*4($sp)
+___
+$code.=<<___ if ($flavour =~ /nubi/i);	# optimize non-nubi prologue
+	sw	$s3, 4*3($sp)
+	sw	$s2, 4*2($sp)
+	sw	$s1, 4*1($sp)
+	sw	$s0, 4*0($sp)
+___
+$code.=<<___;
+	.set	reorder
+
+	srl	$len,4			# number of complete blocks
+	li	$one,1
+	beqz	$len,.Labort
+
+#if defined(_MIPS_ARCH_MIPS32R6)
+	andi	$shr,$inp,3
+	subu	$inp,$inp,$shr		# align $inp
+	sll	$shr,$shr,3		# byte to bit offset
+#endif
+
+	lw	$h0,0($ctx)		# load hash value
+	lw	$h1,4($ctx)
+	lw	$h2,8($ctx)
+	lw	$h3,12($ctx)
+	lw	$h4,16($ctx)
+
+	lw	$r0,20($ctx)		# load key
+	lw	$r1,24($ctx)
+	lw	$r2,28($ctx)
+	lw	$r3,32($ctx)
+	lw	$rs1,36($ctx)
+	lw	$rs2,40($ctx)
+	lw	$rs3,44($ctx)
+
+	sll	$len,4
+	addu	$len,$len,$inp		# end of buffer
+	b	.Loop
+
+.align	4
+.Loop:
+#if defined(_MIPS_ARCH_MIPS32R6)
+	lw	$d0,0($inp)		# load input
+	lw	$d1,4($inp)
+	lw	$d2,8($inp)
+	lw	$d3,12($inp)
+	beqz	$shr,.Laligned_inp
+
+	lw	$t0,16($inp)
+	subu	$t1,$zero,$shr
+# ifdef	MIPSEB
+	sllv	$d0,$d0,$shr
+	srlv	$at,$d1,$t1
+	sllv	$d1,$d1,$shr
+	or	$d0,$d0,$at
+	srlv	$at,$d2,$t1
+	sllv	$d2,$d2,$shr
+	or	$d1,$d1,$at
+	srlv	$at,$d3,$t1
+	sllv	$d3,$d3,$shr
+	or	$d2,$d2,$at
+	srlv	$t0,$t0,$t1
+	or	$d3,$d3,$t0
+# else
+	srlv	$d0,$d0,$shr
+	sllv	$at,$d1,$t1
+	srlv	$d1,$d1,$shr
+	or	$d0,$d0,$at
+	sllv	$at,$d2,$t1
+	srlv	$d2,$d2,$shr
+	or	$d1,$d1,$at
+	sllv	$at,$d3,$t1
+	srlv	$d3,$d3,$shr
+	or	$d2,$d2,$at
+	sllv	$t0,$t0,$t1
+	or	$d3,$d3,$t0
+# endif
+.Laligned_inp:
+#else
+	lwl	$d0,0+MSB($inp)		# load input
+	lwl	$d1,4+MSB($inp)
+	lwl	$d2,8+MSB($inp)
+	lwl	$d3,12+MSB($inp)
+	lwr	$d0,0+LSB($inp)
+	lwr	$d1,4+LSB($inp)
+	lwr	$d2,8+LSB($inp)
+	lwr	$d3,12+LSB($inp)
+#endif
+#ifdef	MIPSEB
+# if defined(_MIPS_ARCH_MIPS32R2)
+	wsbh	$d0,$d0			# byte swap
+	wsbh	$d1,$d1
+	wsbh	$d2,$d2
+	wsbh	$d3,$d3
+	rotr	$d0,$d0,16
+	rotr	$d1,$d1,16
+	rotr	$d2,$d2,16
+	rotr	$d3,$d3,16
+# else
+	srl	$at,$d0,24		# byte swap
+	srl	$t0,$d0,8
+	andi	$t1,$d0,0xFF00
+	sll	$d0,$d0,24
+	andi	$t0,0xFF00
+	sll	$t1,$t1,8
+	or	$d0,$at
+	 srl	$at,$d1,24
+	or	$t0,$t1
+	 srl	$t1,$d1,8
+	or	$d0,$t0
+	 andi	$t0,$d1,0xFF00
+	 sll	$d1,$d1,24
+	 andi	$t1,0xFF00
+	 sll	$t0,$t0,8
+	 or	$d1,$at
+	srl	$at,$d2,24
+	 or	$t1,$t0
+	srl	$t0,$d2,8
+	 or	$d1,$t1
+	andi	$t1,$d2,0xFF00
+	sll	$d2,$d2,24
+	andi	$t0,0xFF00
+	sll	$t1,$t1,8
+	or	$d2,$at
+	 srl	$at,$d3,24
+	or	$t0,$t1
+	 srl	$t1,$d3,8
+	or	$d2,$t0
+	 andi	$t0,$d3,0xFF00
+	 sll	$d3,$d3,24
+	 andi	$t1,0xFF00
+	 sll	$t0,$t0,8
+	 or	$d3,$at
+	 or	$t1,$t0
+	 or	$d3,$t1
+# endif
+#endif
+	srl	$t0,$h4,2		# modulo-scheduled reduction
+	andi	$h4,$h4,3
+	sll	$at,$t0,2
+
+	addu	$d0,$d0,$h0		# accumulate input
+	 addu	$t0,$t0,$at
+	sltu	$h0,$d0,$h0
+	addu	$d0,$d0,$t0		# ... and residue
+	sltu	$at,$d0,$t0
+
+	addu	$d1,$d1,$h1
+	 addu	$h0,$h0,$at		# carry
+	sltu	$h1,$d1,$h1
+	addu	$d1,$d1,$h0
+	sltu	$h0,$d1,$h0
+
+	addu	$d2,$d2,$h2
+	 addu	$h1,$h1,$h0		# carry
+	sltu	$h2,$d2,$h2
+	addu	$d2,$d2,$h1
+	sltu	$h1,$d2,$h1
+
+	addu	$d3,$d3,$h3
+	 addu	$h2,$h2,$h1		# carry
+	sltu	$h3,$d3,$h3
+	addu	$d3,$d3,$h2
+
+#if defined(_MIPS_ARCH_MIPS32R2) && !defined(_MIPS_ARCH_MIPS32R6)
+	multu	$r0,$d0			# d0*r0
+	 sltu	$h2,$d3,$h2
+	maddu	$rs3,$d1		# d1*s3
+	 addu	$h3,$h3,$h2		# carry
+	maddu	$rs2,$d2		# d2*s2
+	 addu	$h4,$h4,$padbit
+	maddu	$rs1,$d3		# d3*s1
+	 addu	$h4,$h4,$h3
+	mfhi	$at
+	mflo	$h0
+
+	multu	$r1,$d0			# d0*r1
+	maddu	$r0,$d1			# d1*r0
+	maddu	$rs3,$d2		# d2*s3
+	maddu	$rs2,$d3		# d3*s2
+	maddu	$rs1,$h4		# h4*s1
+	maddu	$at,$one		# hi*1
+	mfhi	$at
+	mflo	$h1
+
+	multu	$r2,$d0			# d0*r2
+	maddu	$r1,$d1			# d1*r1
+	maddu	$r0,$d2			# d2*r0
+	maddu	$rs3,$d3		# d3*s3
+	maddu	$rs2,$h4		# h4*s2
+	maddu	$at,$one		# hi*1
+	mfhi	$at
+	mflo	$h2
+
+	mul	$t0,$r0,$h4		# h4*r0
+
+	multu	$r3,$d0			# d0*r3
+	maddu	$r2,$d1			# d1*r2
+	maddu	$r1,$d2			# d2*r1
+	maddu	$r0,$d3			# d3*r0
+	maddu	$rs3,$h4		# h4*s3
+	maddu	$at,$one		# hi*1
+	mfhi	$at
+	mflo	$h3
+
+	 addiu	$inp,$inp,16
+
+	addu	$h4,$t0,$at
+#else
+	multu	($r0,$d0)		# d0*r0
+	mflo	($h0,$r0,$d0)
+	mfhi	($h1,$r0,$d0)
+
+	 sltu	$h2,$d3,$h2
+	 addu	$h3,$h3,$h2		# carry
+
+	multu	($rs3,$d1)		# d1*s3
+	mflo	($at,$rs3,$d1)
+	mfhi	($t0,$rs3,$d1)
+
+	 addu	$h4,$h4,$padbit
+	 addiu	$inp,$inp,16
+	 addu	$h4,$h4,$h3
+
+	multu	($rs2,$d2)		# d2*s2
+	mflo	($a3,$rs2,$d2)
+	mfhi	($t1,$rs2,$d2)
+	 addu	$h0,$h0,$at
+	 addu	$h1,$h1,$t0
+	multu	($rs1,$d3)		# d3*s1
+	 sltu	$at,$h0,$at
+	 addu	$h1,$h1,$at
+
+	mflo	($at,$rs1,$d3)
+	mfhi	($t0,$rs1,$d3)
+	 addu	$h0,$h0,$a3
+	 addu	$h1,$h1,$t1
+	multu	($r1,$d0)		# d0*r1
+	 sltu	$a3,$h0,$a3
+	 addu	$h1,$h1,$a3
+
+
+	mflo	($a3,$r1,$d0)
+	mfhi	($h2,$r1,$d0)
+	 addu	$h0,$h0,$at
+	 addu	$h1,$h1,$t0
+	multu	($r0,$d1)		# d1*r0
+	 sltu	$at,$h0,$at
+	 addu	$h1,$h1,$at
+
+	mflo	($at,$r0,$d1)
+	mfhi	($t0,$r0,$d1)
+	 addu	$h1,$h1,$a3
+	 sltu	$a3,$h1,$a3
+	multu	($rs3,$d2)		# d2*s3
+	 addu	$h2,$h2,$a3
+
+	mflo	($a3,$rs3,$d2)
+	mfhi	($t1,$rs3,$d2)
+	 addu	$h1,$h1,$at
+	 addu	$h2,$h2,$t0
+	multu	($rs2,$d3)		# d3*s2
+	 sltu	$at,$h1,$at
+	 addu	$h2,$h2,$at
+
+	mflo	($at,$rs2,$d3)
+	mfhi	($t0,$rs2,$d3)
+	 addu	$h1,$h1,$a3
+	 addu	$h2,$h2,$t1
+	multu	($rs1,$h4)		# h4*s1
+	 sltu	$a3,$h1,$a3
+	 addu	$h2,$h2,$a3
+
+	mflo	($a3,$rs1,$h4)
+	 addu	$h1,$h1,$at
+	 addu	$h2,$h2,$t0
+	multu	($r2,$d0)		# d0*r2
+	 sltu	$at,$h1,$at
+	 addu	$h2,$h2,$at
+
+
+	mflo	($at,$r2,$d0)
+	mfhi	($h3,$r2,$d0)
+	 addu	$h1,$h1,$a3
+	 sltu	$a3,$h1,$a3
+	multu	($r1,$d1)		# d1*r1
+	 addu	$h2,$h2,$a3
+
+	mflo	($a3,$r1,$d1)
+	mfhi	($t1,$r1,$d1)
+	 addu	$h2,$h2,$at
+	 sltu	$at,$h2,$at
+	multu	($r0,$d2)		# d2*r0
+	 addu	$h3,$h3,$at
+
+	mflo	($at,$r0,$d2)
+	mfhi	($t0,$r0,$d2)
+	 addu	$h2,$h2,$a3
+	 addu	$h3,$h3,$t1
+	multu	($rs3,$d3)		# d3*s3
+	 sltu	$a3,$h2,$a3
+	 addu	$h3,$h3,$a3
+
+	mflo	($a3,$rs3,$d3)
+	mfhi	($t1,$rs3,$d3)
+	 addu	$h2,$h2,$at
+	 addu	$h3,$h3,$t0
+	multu	($rs2,$h4)		# h4*s2
+	 sltu	$at,$h2,$at
+	 addu	$h3,$h3,$at
+
+	mflo	($at,$rs2,$h4)
+	 addu	$h2,$h2,$a3
+	 addu	$h3,$h3,$t1
+	multu	($r3,$d0)		# d0*r3
+	 sltu	$a3,$h2,$a3
+	 addu	$h3,$h3,$a3
+
+
+	mflo	($a3,$r3,$d0)
+	mfhi	($t1,$r3,$d0)
+	 addu	$h2,$h2,$at
+	 sltu	$at,$h2,$at
+	multu	($r2,$d1)		# d1*r2
+	 addu	$h3,$h3,$at
+
+	mflo	($at,$r2,$d1)
+	mfhi	($t0,$r2,$d1)
+	 addu	$h3,$h3,$a3
+	 sltu	$a3,$h3,$a3
+	multu	($r0,$d3)		# d3*r0
+	 addu	$t1,$t1,$a3
+
+	mflo	($a3,$r0,$d3)
+	mfhi	($d3,$r0,$d3)
+	 addu	$h3,$h3,$at
+	 addu	$t1,$t1,$t0
+	multu	($r1,$d2)		# d2*r1
+	 sltu	$at,$h3,$at
+	 addu	$t1,$t1,$at
+
+	mflo	($at,$r1,$d2)
+	mfhi	($t0,$r1,$d2)
+	 addu	$h3,$h3,$a3
+	 addu	$t1,$t1,$d3
+	multu	($rs3,$h4)		# h4*s3
+	 sltu	$a3,$h3,$a3
+	 addu	$t1,$t1,$a3
+
+	mflo	($a3,$rs3,$h4)
+	 addu	$h3,$h3,$at
+	 addu	$t1,$t1,$t0
+	multu	($r0,$h4)		# h4*r0
+	 sltu	$at,$h3,$at
+	 addu	$t1,$t1,$at
+
+
+	mflo	($h4,$r0,$h4)
+	 addu	$h3,$h3,$a3
+	 sltu	$a3,$h3,$a3
+	 addu	$t1,$t1,$a3
+	addu	$h4,$h4,$t1
+
+	li	$padbit,1		# if we loop, padbit is 1
+#endif
+	bne	$inp,$len,.Loop
+
+	sw	$h0,0($ctx)		# store hash value
+	sw	$h1,4($ctx)
+	sw	$h2,8($ctx)
+	sw	$h3,12($ctx)
+	sw	$h4,16($ctx)
+
+	.set	noreorder
+.Labort:
+	lw	$s11,4*11($sp)
+	lw	$s10,4*10($sp)
+	lw	$s9, 4*9($sp)
+	lw	$s8, 4*8($sp)
+	lw	$s7, 4*7($sp)
+	lw	$s6, 4*6($sp)
+	lw	$s5, 4*5($sp)
+	lw	$s4, 4*4($sp)
+___
+$code.=<<___ if ($flavour =~ /nubi/i);	# optimize non-nubi prologue
+	lw	$s3, 4*3($sp)
+	lw	$s2, 4*2($sp)
+	lw	$s1, 4*1($sp)
+	lw	$s0, 4*0($sp)
+___
+$code.=<<___;
+	jr	$ra
+	addu	$sp,$sp,4*12
+.end	poly1305_blocks
+___
+}
+{
+my ($ctx,$mac,$nonce,$tmp4) = ($a0,$a1,$a2,$a3);
+
+$code.=<<___;
+.align	5
+.globl	poly1305_emit
+.ent	poly1305_emit
+poly1305_emit:
+	.frame	$sp,0,$ra
+	.set	reorder
+
+	lw	$tmp4,16($ctx)
+	lw	$tmp0,0($ctx)
+	lw	$tmp1,4($ctx)
+	lw	$tmp2,8($ctx)
+	lw	$tmp3,12($ctx)
+
+	li	$in0,-4			# final reduction
+	srl	$ctx,$tmp4,2
+	and	$in0,$in0,$tmp4
+	andi	$tmp4,$tmp4,3
+	addu	$ctx,$ctx,$in0
+
+	addu	$tmp0,$tmp0,$ctx
+	sltu	$ctx,$tmp0,$ctx
+	 addiu	$in0,$tmp0,5		# compare to modulus
+	addu	$tmp1,$tmp1,$ctx
+	 sltiu	$in1,$in0,5
+	sltu	$ctx,$tmp1,$ctx
+	 addu	$in1,$in1,$tmp1
+	addu	$tmp2,$tmp2,$ctx
+	 sltu	$in2,$in1,$tmp1
+	sltu	$ctx,$tmp2,$ctx
+	 addu	$in2,$in2,$tmp2
+	addu	$tmp3,$tmp3,$ctx
+	 sltu	$in3,$in2,$tmp2
+	sltu	$ctx,$tmp3,$ctx
+	 addu	$in3,$in3,$tmp3
+	addu	$tmp4,$tmp4,$ctx
+	 sltu	$ctx,$in3,$tmp3
+	 addu	$ctx,$tmp4
+
+	srl	$ctx,2			# see if it carried/borrowed
+	subu	$ctx,$zero,$ctx
+
+	xor	$in0,$tmp0
+	xor	$in1,$tmp1
+	xor	$in2,$tmp2
+	xor	$in3,$tmp3
+	and	$in0,$ctx
+	and	$in1,$ctx
+	and	$in2,$ctx
+	and	$in3,$ctx
+	xor	$in0,$tmp0
+	xor	$in1,$tmp1
+	xor	$in2,$tmp2
+	xor	$in3,$tmp3
+
+	lw	$tmp0,0($nonce)		# load nonce
+	lw	$tmp1,4($nonce)
+	lw	$tmp2,8($nonce)
+	lw	$tmp3,12($nonce)
+
+	addu	$in0,$tmp0		# accumulate nonce
+	sltu	$ctx,$in0,$tmp0
+
+	addu	$in1,$tmp1
+	sltu	$tmp1,$in1,$tmp1
+	addu	$in1,$ctx
+	sltu	$ctx,$in1,$ctx
+	addu	$ctx,$tmp1
+
+	addu	$in2,$tmp2
+	sltu	$tmp2,$in2,$tmp2
+	addu	$in2,$ctx
+	sltu	$ctx,$in2,$ctx
+	addu	$ctx,$tmp2
+
+	addu	$in3,$tmp3
+	addu	$in3,$ctx
+
+	srl	$tmp0,$in0,8		# write mac value
+	srl	$tmp1,$in0,16
+	srl	$tmp2,$in0,24
+	sb	$in0, 0($mac)
+	sb	$tmp0,1($mac)
+	srl	$tmp0,$in1,8
+	sb	$tmp1,2($mac)
+	srl	$tmp1,$in1,16
+	sb	$tmp2,3($mac)
+	srl	$tmp2,$in1,24
+	sb	$in1, 4($mac)
+	sb	$tmp0,5($mac)
+	srl	$tmp0,$in2,8
+	sb	$tmp1,6($mac)
+	srl	$tmp1,$in2,16
+	sb	$tmp2,7($mac)
+	srl	$tmp2,$in2,24
+	sb	$in2, 8($mac)
+	sb	$tmp0,9($mac)
+	srl	$tmp0,$in3,8
+	sb	$tmp1,10($mac)
+	srl	$tmp1,$in3,16
+	sb	$tmp2,11($mac)
+	srl	$tmp2,$in3,24
+	sb	$in3, 12($mac)
+	sb	$tmp0,13($mac)
+	sb	$tmp1,14($mac)
+	sb	$tmp2,15($mac)
+
+	jr	$ra
+.end	poly1305_emit
+.rdata
+.asciiz	"Poly1305 for MIPS32, CRYPTOGAMS by \@dot-asm"
+.align	2
+___
+}
+}}}
+
+$output=pop and open STDOUT,">$output";
+print $code;
+close STDOUT;
diff --git a/arch/mips/dec/Makefile b/arch/mips/dec/Makefile
new file mode 100644
index 000000000..c9f62f1da
--- /dev/null
+++ b/arch/mips/dec/Makefile
@@ -0,0 +1,10 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Makefile for the DECstation family specific parts of the kernel
+#
+
+obj-y		:= ecc-berr.o int-handler.o ioasic-irq.o kn01-berr.o \
+		   kn02-irq.o kn02xa-berr.o platform.o reset.o setup.o time.o
+
+obj-$(CONFIG_TC)		+= tc.o
+obj-$(CONFIG_CPU_HAS_WB)	+= wbflush.o
diff --git a/arch/mips/dec/Platform b/arch/mips/dec/Platform
new file mode 100644
index 000000000..c82391e83
--- /dev/null
+++ b/arch/mips/dec/Platform
@@ -0,0 +1,7 @@
+#
+# DECstation family
+#
+cflags-$(CONFIG_MACH_DECSTATION)	+= \
+			-I$(srctree)/arch/mips/include/asm/mach-dec
+libs-$(CONFIG_MACH_DECSTATION)		+= arch/mips/dec/prom/
+load-$(CONFIG_MACH_DECSTATION)		+= 0xffffffff80040000
diff --git a/arch/mips/dec/ecc-berr.c b/arch/mips/dec/ecc-berr.c
new file mode 100644
index 000000000..1eb356fdd
--- /dev/null
+++ b/arch/mips/dec/ecc-berr.c
@@ -0,0 +1,274 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *	Bus error event handling code for systems equipped with ECC
+ *	handling logic, i.e. DECstation/DECsystem 5000/200 (KN02),
+ *	5000/240 (KN03), 5000/260 (KN05) and DECsystem 5900 (KN03),
+ *	5900/260 (KN05) systems.
+ *
+ *	Copyright (c) 2003, 2005  Maciej W. Rozycki
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/types.h>
+
+#include <asm/addrspace.h>
+#include <asm/bootinfo.h>
+#include <asm/cpu.h>
+#include <asm/cpu-type.h>
+#include <asm/irq_regs.h>
+#include <asm/processor.h>
+#include <asm/ptrace.h>
+#include <asm/traps.h>
+
+#include <asm/dec/ecc.h>
+#include <asm/dec/kn02.h>
+#include <asm/dec/kn03.h>
+#include <asm/dec/kn05.h>
+
+static volatile u32 *kn0x_erraddr;
+static volatile u32 *kn0x_chksyn;
+
+static inline void dec_ecc_be_ack(void)
+{
+	*kn0x_erraddr = 0;			/* any write clears the IRQ */
+	iob();
+}
+
+static int dec_ecc_be_backend(struct pt_regs *regs, int is_fixup, int invoker)
+{
+	static const char excstr[] = "exception";
+	static const char intstr[] = "interrupt";
+	static const char cpustr[] = "CPU";
+	static const char dmastr[] = "DMA";
+	static const char readstr[] = "read";
+	static const char mreadstr[] = "memory read";
+	static const char writestr[] = "write";
+	static const char mwritstr[] = "partial memory write";
+	static const char timestr[] = "timeout";
+	static const char overstr[] = "overrun";
+	static const char eccstr[] = "ECC error";
+
+	const char *kind, *agent, *cycle, *event;
+	const char *status = "", *xbit = "", *fmt = "";
+	unsigned long address;
+	u16 syn = 0, sngl;
+
+	int i = 0;
+
+	u32 erraddr = *kn0x_erraddr;
+	u32 chksyn = *kn0x_chksyn;
+	int action = MIPS_BE_FATAL;
+
+	/* For non-ECC ack ASAP, so that any subsequent errors get caught. */
+	if ((erraddr & (KN0X_EAR_VALID | KN0X_EAR_ECCERR)) == KN0X_EAR_VALID)
+		dec_ecc_be_ack();
+
+	kind = invoker ? intstr : excstr;
+
+	if (!(erraddr & KN0X_EAR_VALID)) {
+		/* No idea what happened. */
+		printk(KERN_ALERT "Unidentified bus error %s\n", kind);
+		return action;
+	}
+
+	agent = (erraddr & KN0X_EAR_CPU) ? cpustr : dmastr;
+
+	if (erraddr & KN0X_EAR_ECCERR) {
+		/* An ECC error on a CPU or DMA transaction. */
+		cycle = (erraddr & KN0X_EAR_WRITE) ? mwritstr : mreadstr;
+		event = eccstr;
+	} else {
+		/* A CPU timeout or a DMA overrun. */
+		cycle = (erraddr & KN0X_EAR_WRITE) ? writestr : readstr;
+		event = (erraddr & KN0X_EAR_CPU) ? timestr : overstr;
+	}
+
+	address = erraddr & KN0X_EAR_ADDRESS;
+	/* For ECC errors on reads adjust for MT pipelining. */
+	if ((erraddr & (KN0X_EAR_WRITE | KN0X_EAR_ECCERR)) == KN0X_EAR_ECCERR)
+		address = (address & ~0xfffLL) | ((address - 5) & 0xfffLL);
+	address <<= 2;
+
+	/* Only CPU errors are fixable. */
+	if (erraddr & KN0X_EAR_CPU && is_fixup)
+		action = MIPS_BE_FIXUP;
+
+	if (erraddr & KN0X_EAR_ECCERR) {
+		static const u8 data_sbit[32] = {
+			0x4f, 0x4a, 0x52, 0x54, 0x57, 0x58, 0x5b, 0x5d,
+			0x23, 0x25, 0x26, 0x29, 0x2a, 0x2c, 0x31, 0x34,
+			0x0e, 0x0b, 0x13, 0x15, 0x16, 0x19, 0x1a, 0x1c,
+			0x62, 0x64, 0x67, 0x68, 0x6b, 0x6d, 0x70, 0x75,
+		};
+		static const u8 data_mbit[25] = {
+			0x07, 0x0d, 0x1f,
+			0x2f, 0x32, 0x37, 0x38, 0x3b, 0x3d, 0x3e,
+			0x43, 0x45, 0x46, 0x49, 0x4c, 0x51, 0x5e,
+			0x61, 0x6e, 0x73, 0x76, 0x79, 0x7a, 0x7c, 0x7f,
+		};
+		static const char sbestr[] = "corrected single";
+		static const char dbestr[] = "uncorrectable double";
+		static const char mbestr[] = "uncorrectable multiple";
+
+		if (!(address & 0x4))
+			syn = chksyn;			/* Low bank. */
+		else
+			syn = chksyn >> 16;		/* High bank. */
+
+		if (!(syn & KN0X_ESR_VLDLO)) {
+			/* Ack now, no rewrite will happen. */
+			dec_ecc_be_ack();
+
+			fmt = KERN_ALERT "%s" "invalid\n";
+		} else {
+			sngl = syn & KN0X_ESR_SNGLO;
+			syn &= KN0X_ESR_SYNLO;
+
+			/*
+			 * Multibit errors may be tagged incorrectly;
+			 * check the syndrome explicitly.
+			 */
+			for (i = 0; i < 25; i++)
+				if (syn == data_mbit[i])
+					break;
+
+			if (i < 25) {
+				status = mbestr;
+			} else if (!sngl) {
+				status = dbestr;
+			} else {
+				volatile u32 *ptr =
+					(void *)CKSEG1ADDR(address);
+
+				*ptr = *ptr;		/* Rewrite. */
+				iob();
+
+				status = sbestr;
+				action = MIPS_BE_DISCARD;
+			}
+
+			/* Ack now, now we've rewritten (or not). */
+			dec_ecc_be_ack();
+
+			if (syn && syn == (syn & -syn)) {
+				if (syn == 0x01) {
+					fmt = KERN_ALERT "%s"
+					      "%#04x -- %s bit error "
+					      "at check bit C%s\n";
+					xbit = "X";
+				} else {
+					fmt = KERN_ALERT "%s"
+					      "%#04x -- %s bit error "
+					      "at check bit C%s%u\n";
+				}
+				i = syn >> 2;
+			} else {
+				for (i = 0; i < 32; i++)
+					if (syn == data_sbit[i])
+						break;
+				if (i < 32)
+					fmt = KERN_ALERT "%s"
+					      "%#04x -- %s bit error "
+					      "at data bit D%s%u\n";
+				else
+					fmt = KERN_ALERT "%s"
+					      "%#04x -- %s bit error\n";
+			}
+		}
+	}
+
+	if (action != MIPS_BE_FIXUP)
+		printk(KERN_ALERT "Bus error %s: %s %s %s at %#010lx\n",
+			kind, agent, cycle, event, address);
+
+	if (action != MIPS_BE_FIXUP && erraddr & KN0X_EAR_ECCERR)
+		printk(fmt, "  ECC syndrome ", syn, status, xbit, i);
+
+	return action;
+}
+
+int dec_ecc_be_handler(struct pt_regs *regs, int is_fixup)
+{
+	return dec_ecc_be_backend(regs, is_fixup, 0);
+}
+
+irqreturn_t dec_ecc_be_interrupt(int irq, void *dev_id)
+{
+	struct pt_regs *regs = get_irq_regs();
+
+	int action = dec_ecc_be_backend(regs, 0, 1);
+
+	if (action == MIPS_BE_DISCARD)
+		return IRQ_HANDLED;
+
+	/*
+	 * FIXME: Find the affected processes and kill them, otherwise
+	 * we must die.
+	 *
+	 * The interrupt is asynchronously delivered thus EPC and RA
+	 * may be irrelevant, but are printed for a reference.
+	 */
+	printk(KERN_ALERT "Fatal bus interrupt, epc == %08lx, ra == %08lx\n",
+	       regs->cp0_epc, regs->regs[31]);
+	die("Unrecoverable bus error", regs);
+}
+
+
+/*
+ * Initialization differs a bit between KN02 and KN03/KN05, so we
+ * need two variants.  Once set up, all systems can be handled the
+ * same way.
+ */
+static inline void dec_kn02_be_init(void)
+{
+	volatile u32 *csr = (void *)CKSEG1ADDR(KN02_SLOT_BASE + KN02_CSR);
+
+	kn0x_erraddr = (void *)CKSEG1ADDR(KN02_SLOT_BASE + KN02_ERRADDR);
+	kn0x_chksyn = (void *)CKSEG1ADDR(KN02_SLOT_BASE + KN02_CHKSYN);
+
+	/* Preset write-only bits of the Control Register cache. */
+	cached_kn02_csr = *csr | KN02_CSR_LEDS;
+
+	/* Set normal ECC detection and generation. */
+	cached_kn02_csr &= ~(KN02_CSR_DIAGCHK | KN02_CSR_DIAGGEN);
+	/* Enable ECC correction. */
+	cached_kn02_csr |= KN02_CSR_CORRECT;
+	*csr = cached_kn02_csr;
+	iob();
+}
+
+static inline void dec_kn03_be_init(void)
+{
+	volatile u32 *mcr = (void *)CKSEG1ADDR(KN03_SLOT_BASE + IOASIC_MCR);
+	volatile u32 *mbcs = (void *)CKSEG1ADDR(KN4K_SLOT_BASE + KN4K_MB_CSR);
+
+	kn0x_erraddr = (void *)CKSEG1ADDR(KN03_SLOT_BASE + IOASIC_ERRADDR);
+	kn0x_chksyn = (void *)CKSEG1ADDR(KN03_SLOT_BASE + IOASIC_CHKSYN);
+
+	/*
+	 * Set normal ECC detection and generation, enable ECC correction.
+	 * For KN05 we also need to make sure EE (?) is enabled in the MB.
+	 * Otherwise DBE/IBE exceptions would be masked but bus error
+	 * interrupts would still arrive, resulting in an inevitable crash
+	 * if get_dbe() triggers one.
+	 */
+	*mcr = (*mcr & ~(KN03_MCR_DIAGCHK | KN03_MCR_DIAGGEN)) |
+	       KN03_MCR_CORRECT;
+	if (current_cpu_type() == CPU_R4400SC)
+		*mbcs |= KN4K_MB_CSR_EE;
+	fast_iob();
+}
+
+void __init dec_ecc_be_init(void)
+{
+	if (mips_machtype == MACH_DS5000_200)
+		dec_kn02_be_init();
+	else
+		dec_kn03_be_init();
+
+	/* Clear any leftover errors from the firmware. */
+	dec_ecc_be_ack();
+}
diff --git a/arch/mips/dec/int-handler.S b/arch/mips/dec/int-handler.S
new file mode 100644
index 000000000..011d1d678
--- /dev/null
+++ b/arch/mips/dec/int-handler.S
@@ -0,0 +1,311 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 1995, 1996, 1997 Paul M. Antoine and Harald Koerfgen
+ * Copyright (C) 2000, 2001, 2002, 2003, 2005  Maciej W. Rozycki
+ *
+ * Written by Ralf Baechle and Andreas Busse, modified for DECstation
+ * support by Paul Antoine and Harald Koerfgen.
+ *
+ * completely rewritten:
+ * Copyright (C) 1998 Harald Koerfgen
+ *
+ * Rewritten extensively for controller-driven IRQ support
+ * by Maciej W. Rozycki.
+ */
+
+#include <asm/addrspace.h>
+#include <asm/asm.h>
+#include <asm/mipsregs.h>
+#include <asm/regdef.h>
+#include <asm/stackframe.h>
+
+#include <asm/dec/interrupts.h>
+#include <asm/dec/ioasic_addrs.h>
+#include <asm/dec/ioasic_ints.h>
+#include <asm/dec/kn01.h>
+#include <asm/dec/kn02.h>
+#include <asm/dec/kn02xa.h>
+#include <asm/dec/kn03.h>
+
+#define KN02_CSR_BASE		CKSEG1ADDR(KN02_SLOT_BASE + KN02_CSR)
+#define KN02XA_IOASIC_BASE	CKSEG1ADDR(KN02XA_SLOT_BASE + IOASIC_IOCTL)
+#define KN03_IOASIC_BASE	CKSEG1ADDR(KN03_SLOT_BASE + IOASIC_IOCTL)
+
+		.text
+		.set	noreorder
+/*
+ * plat_irq_dispatch: Interrupt handler for DECstations
+ *
+ * We follow the model in the Indy interrupt code by David Miller, where he
+ * says: a lot of complication here is taken away because:
+ *
+ * 1) We handle one interrupt and return, sitting in a loop
+ *    and moving across all the pending IRQ bits in the cause
+ *    register is _NOT_ the answer, the common case is one
+ *    pending IRQ so optimize in that direction.
+ *
+ * 2) We need not check against bits in the status register
+ *    IRQ mask, that would make this routine slow as hell.
+ *
+ * 3) Linux only thinks in terms of all IRQs on or all IRQs
+ *    off, nothing in between like BSD spl() brain-damage.
+ *
+ * Furthermore, the IRQs on the DECstations look basically (barring
+ * software IRQs which we don't use at all) like...
+ *
+ * DS2100/3100's, aka kn01, aka Pmax:
+ *
+ *	MIPS IRQ	Source
+ *	--------	------
+ *	       0	Software (ignored)
+ *	       1	Software (ignored)
+ *	       2	SCSI
+ *	       3	Lance Ethernet
+ *	       4	DZ11 serial
+ *	       5	RTC
+ *	       6	Memory Controller & Video
+ *	       7	FPU
+ *
+ * DS5000/200, aka kn02, aka 3max:
+ *
+ *	MIPS IRQ	Source
+ *	--------	------
+ *	       0	Software (ignored)
+ *	       1	Software (ignored)
+ *	       2	TurboChannel
+ *	       3	RTC
+ *	       4	Reserved
+ *	       5	Memory Controller
+ *	       6	Reserved
+ *	       7	FPU
+ *
+ * DS5000/1xx's, aka kn02ba, aka 3min:
+ *
+ *	MIPS IRQ	Source
+ *	--------	------
+ *	       0	Software (ignored)
+ *	       1	Software (ignored)
+ *	       2	TurboChannel Slot 0
+ *	       3	TurboChannel Slot 1
+ *	       4	TurboChannel Slot 2
+ *	       5	TurboChannel Slot 3 (ASIC)
+ *	       6	Halt button
+ *	       7	FPU/R4k timer
+ *
+ * DS5000/2x's, aka kn02ca, aka maxine:
+ *
+ *	MIPS IRQ	Source
+ *	--------	------
+ *	       0	Software (ignored)
+ *	       1	Software (ignored)
+ *	       2	Periodic Interrupt (100usec)
+ *	       3	RTC
+ *	       4	I/O write timeout
+ *	       5	TurboChannel (ASIC)
+ *	       6	Halt Keycode from Access.Bus keyboard (CTRL-ALT-ENTER)
+ *	       7	FPU/R4k timer
+ *
+ * DS5000/2xx's, aka kn03, aka 3maxplus:
+ *
+ *	MIPS IRQ	Source
+ *	--------	------
+ *	       0	Software (ignored)
+ *	       1	Software (ignored)
+ *	       2	System Board (ASIC)
+ *	       3	RTC
+ *	       4	Reserved
+ *	       5	Memory
+ *	       6	Halt Button
+ *	       7	FPU/R4k timer
+ *
+ * We handle the IRQ according to _our_ priority (see setup.c),
+ * then we just return.  If multiple IRQs are pending then we will
+ * just take another exception, big deal.
+ */
+		.align	5
+		NESTED(plat_irq_dispatch, PT_SIZE, ra)
+		.set	noreorder
+
+		/*
+		 * Get pending Interrupts
+		 */
+		mfc0	t0,CP0_CAUSE		# get pending interrupts
+		mfc0	t1,CP0_STATUS
+#if defined(CONFIG_32BIT) && defined(CONFIG_MIPS_FP_SUPPORT)
+		lw	t2,cpu_fpu_mask
+#endif
+		andi	t0,ST0_IM		# CAUSE.CE may be non-zero!
+		and	t0,t1			# isolate allowed ones
+
+		beqz	t0,spurious
+
+#if defined(CONFIG_32BIT) && defined(CONFIG_MIPS_FP_SUPPORT)
+		 and	t2,t0
+		bnez	t2,fpu			# handle FPU immediately
+#endif
+
+		/*
+		 * Find irq with highest priority
+		 */
+		# open coded PTR_LA t1, cpu_mask_nr_tbl
+#if defined(CONFIG_32BIT) || defined(KBUILD_64BIT_SYM32)
+		# open coded la t1, cpu_mask_nr_tbl
+		lui	t1, %hi(cpu_mask_nr_tbl)
+		addiu	t1, %lo(cpu_mask_nr_tbl)
+#else
+#error GCC `-msym32' option required for 64-bit DECstation builds
+#endif
+1:		lw	t2,(t1)
+		nop
+		and	t2,t0
+		beqz	t2,1b
+		 addu	t1,2*PTRSIZE		# delay slot
+
+		/*
+		 * Do the low-level stuff
+		 */
+		lw	a0,(-PTRSIZE)(t1)
+		nop
+		bgez	a0,handle_it		# irq_nr >= 0?
+						# irq_nr < 0: it is an address
+		 nop
+		jr	a0
+						# a trick to save a branch:
+		 lui	t2,(KN03_IOASIC_BASE>>16)&0xffff
+						# upper part of IOASIC Address
+
+/*
+ * Handle "IRQ Controller" Interrupts
+ * Masked Interrupts are still visible and have to be masked "by hand".
+ */
+		FEXPORT(kn02_io_int)		# 3max
+		lui	t0,(KN02_CSR_BASE>>16)&0xffff
+						# get interrupt status and mask
+		lw	t0,(t0)
+		nop
+		andi	t1,t0,KN02_IRQ_ALL
+		b	1f
+		 srl	t0,16			# shift interrupt mask
+
+		FEXPORT(kn02xa_io_int)		# 3min/maxine
+		lui	t2,(KN02XA_IOASIC_BASE>>16)&0xffff
+						# upper part of IOASIC Address
+
+		FEXPORT(kn03_io_int)		# 3max+ (t2 loaded earlier)
+		lw	t0,IO_REG_SIR(t2)	# get status: IOASIC sir
+		lw	t1,IO_REG_SIMR(t2)	# get mask:   IOASIC simr
+		nop
+
+1:		and	t0,t1			# mask out allowed ones
+
+		beqz	t0,spurious
+
+		/*
+		 * Find irq with highest priority
+		 */
+		# open coded PTR_LA t1,asic_mask_nr_tbl
+#if defined(CONFIG_32BIT) || defined(KBUILD_64BIT_SYM32)
+		# open coded la t1, asic_mask_nr_tbl
+		lui	t1, %hi(asic_mask_nr_tbl)
+		addiu	t1, %lo(asic_mask_nr_tbl)
+#else
+#error GCC `-msym32' option required for 64-bit DECstation builds
+#endif
+2:		lw	t2,(t1)
+		nop
+		and	t2,t0
+		beq	zero,t2,2b
+		 addu	t1,2*PTRSIZE		# delay slot
+
+		/*
+		 * Do the low-level stuff
+		 */
+		lw	a0,%lo(-PTRSIZE)(t1)
+		nop
+		bgez	a0,handle_it		# irq_nr >= 0?
+						# irq_nr < 0: it is an address
+		 nop
+		jr	a0
+		 nop				# delay slot
+
+/*
+ * Dispatch low-priority interrupts.  We reconsider all status
+ * bits again, which looks like a lose, but it makes the code
+ * simple and O(log n), so it gets compensated.
+ */
+		FEXPORT(cpu_all_int)		# HALT, timers, software junk
+		li	a0,DEC_CPU_IRQ_BASE
+		srl	t0,CAUSEB_IP
+		li	t1,CAUSEF_IP>>CAUSEB_IP	# mask
+		b	1f
+		 li	t2,4			# nr of bits / 2
+
+		FEXPORT(kn02_all_int)		# impossible ?
+		li	a0,KN02_IRQ_BASE
+		li	t1,KN02_IRQ_ALL		# mask
+		b	1f
+		 li	t2,4			# nr of bits / 2
+
+		FEXPORT(asic_all_int)		# various I/O ASIC junk
+		li	a0,IO_IRQ_BASE
+		li	t1,IO_IRQ_ALL		# mask
+		b	1f
+		 li	t2,8			# nr of bits / 2
+
+/*
+ * Dispatch DMA interrupts -- O(log n).
+ */
+		FEXPORT(asic_dma_int)		# I/O ASIC DMA events
+		li	a0,IO_IRQ_BASE+IO_INR_DMA
+		srl	t0,IO_INR_DMA
+		li	t1,IO_IRQ_DMA>>IO_INR_DMA # mask
+		li	t2,8			# nr of bits / 2
+
+		/*
+		 * Find irq with highest priority.
+		 * Highest irq number takes precedence.
+		 */
+1:		srlv	t3,t1,t2
+2:		xor	t1,t3
+		and	t3,t0,t1
+		beqz	t3,3f
+		 nop
+		move	t0,t3
+		addu	a0,t2
+3:		srl	t2,1
+		bnez	t2,2b
+		 srlv	t3,t1,t2
+
+handle_it:
+		j	dec_irq_dispatch
+		 nop
+
+#if defined(CONFIG_32BIT) && defined(CONFIG_MIPS_FP_SUPPORT)
+fpu:
+		lw	t0,fpu_kstat_irq
+		nop
+		lw	t1,(t0)
+		nop
+		addu	t1,1
+		j	handle_fpe_int
+		 sw	t1,(t0)
+#endif
+
+spurious:
+		j	spurious_interrupt
+		 nop
+		END(plat_irq_dispatch)
+
+/*
+ * Generic unimplemented interrupt routines -- cpu_mask_nr_tbl
+ * and asic_mask_nr_tbl are initialized to point all interrupts here.
+ * The tables are then filled in by machine-specific initialisation
+ * in dec_setup().
+ */
+		FEXPORT(dec_intr_unimplemented)
+		move	a1,t0			# cheats way of printing an arg!
+		ASM_PANIC("Unimplemented cpu interrupt! CP0_CAUSE: 0x%08x");
+
+		FEXPORT(asic_intr_unimplemented)
+		move	a1,t0			# cheats way of printing an arg!
+		ASM_PANIC("Unimplemented asic interrupt! ASIC ISR: 0x%08x");
diff --git a/arch/mips/dec/ioasic-irq.c b/arch/mips/dec/ioasic-irq.c
new file mode 100644
index 000000000..971f7b467
--- /dev/null
+++ b/arch/mips/dec/ioasic-irq.c
@@ -0,0 +1,112 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *	DEC I/O ASIC interrupts.
+ *
+ *	Copyright (c) 2002, 2003, 2013  Maciej W. Rozycki
+ */
+
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <linux/types.h>
+
+#include <asm/dec/ioasic.h>
+#include <asm/dec/ioasic_addrs.h>
+#include <asm/dec/ioasic_ints.h>
+
+static int ioasic_irq_base;
+
+static void unmask_ioasic_irq(struct irq_data *d)
+{
+	u32 simr;
+
+	simr = ioasic_read(IO_REG_SIMR);
+	simr |= (1 << (d->irq - ioasic_irq_base));
+	ioasic_write(IO_REG_SIMR, simr);
+}
+
+static void mask_ioasic_irq(struct irq_data *d)
+{
+	u32 simr;
+
+	simr = ioasic_read(IO_REG_SIMR);
+	simr &= ~(1 << (d->irq - ioasic_irq_base));
+	ioasic_write(IO_REG_SIMR, simr);
+}
+
+static void ack_ioasic_irq(struct irq_data *d)
+{
+	mask_ioasic_irq(d);
+	fast_iob();
+}
+
+static struct irq_chip ioasic_irq_type = {
+	.name = "IO-ASIC",
+	.irq_ack = ack_ioasic_irq,
+	.irq_mask = mask_ioasic_irq,
+	.irq_mask_ack = ack_ioasic_irq,
+	.irq_unmask = unmask_ioasic_irq,
+};
+
+static void clear_ioasic_dma_irq(struct irq_data *d)
+{
+	u32 sir;
+
+	sir = ~(1 << (d->irq - ioasic_irq_base));
+	ioasic_write(IO_REG_SIR, sir);
+	fast_iob();
+}
+
+static struct irq_chip ioasic_dma_irq_type = {
+	.name = "IO-ASIC-DMA",
+	.irq_ack = clear_ioasic_dma_irq,
+	.irq_mask = mask_ioasic_irq,
+	.irq_unmask = unmask_ioasic_irq,
+	.irq_eoi = clear_ioasic_dma_irq,
+};
+
+/*
+ * I/O ASIC implements two kinds of DMA interrupts, informational and
+ * error interrupts.
+ *
+ * The former do not stop DMA and should be cleared as soon as possible
+ * so that if they retrigger before the handler has completed, usually as
+ * a side effect of actions taken by the handler, then they are reissued.
+ * These use the `handle_edge_irq' handler that clears the request right
+ * away.
+ *
+ * The latter stop DMA and do not resume it until the interrupt has been
+ * cleared.  This cannot be done until after a corrective action has been
+ * taken and this also means they will not retrigger.  Therefore they use
+ * the `handle_fasteoi_irq' handler that only clears the request on the
+ * way out.  Because MIPS processor interrupt inputs, one of which the I/O
+ * ASIC is cascaded to, are level-triggered it is recommended that error
+ * DMA interrupt action handlers are registered with the IRQF_ONESHOT flag
+ * set so that they are run with the interrupt line masked.
+ *
+ * This mask has `1' bits in the positions of informational interrupts.
+ */
+#define IO_IRQ_DMA_INFO							\
+	(IO_IRQ_MASK(IO_INR_SCC0A_RXDMA) |				\
+	 IO_IRQ_MASK(IO_INR_SCC1A_RXDMA) |				\
+	 IO_IRQ_MASK(IO_INR_ISDN_TXDMA) |				\
+	 IO_IRQ_MASK(IO_INR_ISDN_RXDMA) |				\
+	 IO_IRQ_MASK(IO_INR_ASC_DMA))
+
+void __init init_ioasic_irqs(int base)
+{
+	int i;
+
+	/* Mask interrupts. */
+	ioasic_write(IO_REG_SIMR, 0);
+	fast_iob();
+
+	for (i = base; i < base + IO_INR_DMA; i++)
+		irq_set_chip_and_handler(i, &ioasic_irq_type,
+					 handle_level_irq);
+	for (; i < base + IO_IRQ_LINES; i++)
+		irq_set_chip_and_handler(i, &ioasic_dma_irq_type,
+					 1 << (i - base) & IO_IRQ_DMA_INFO ?
+					 handle_edge_irq : handle_fasteoi_irq);
+
+	ioasic_irq_base = base;
+}
diff --git a/arch/mips/dec/kn01-berr.c b/arch/mips/dec/kn01-berr.c
new file mode 100644
index 000000000..76efed7bc
--- /dev/null
+++ b/arch/mips/dec/kn01-berr.c
@@ -0,0 +1,196 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *	Bus error event handling code for DECstation/DECsystem 3100
+ *	and 2100 (KN01) systems equipped with parity error detection
+ *	logic.
+ *
+ *	Copyright (c) 2005  Maciej W. Rozycki
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/spinlock.h>
+#include <linux/types.h>
+
+#include <asm/inst.h>
+#include <asm/irq_regs.h>
+#include <asm/mipsregs.h>
+#include <asm/page.h>
+#include <asm/ptrace.h>
+#include <asm/traps.h>
+#include <linux/uaccess.h>
+
+#include <asm/dec/kn01.h>
+
+
+/* CP0 hazard avoidance. */
+#define BARRIER				\
+	__asm__ __volatile__(		\
+		".set	push\n\t"	\
+		".set	noreorder\n\t"	\
+		"nop\n\t"		\
+		".set	pop\n\t")
+
+/*
+ * Bits 7:0 of the Control Register are write-only -- the
+ * corresponding bits of the Status Register have a different
+ * meaning.  Hence we use a cache.  It speeds up things a bit
+ * as well.
+ *
+ * There is no default value -- it has to be initialized.
+ */
+u16 cached_kn01_csr;
+static DEFINE_RAW_SPINLOCK(kn01_lock);
+
+
+static inline void dec_kn01_be_ack(void)
+{
+	volatile u16 *csr = (void *)CKSEG1ADDR(KN01_SLOT_BASE + KN01_CSR);
+	unsigned long flags;
+
+	raw_spin_lock_irqsave(&kn01_lock, flags);
+
+	*csr = cached_kn01_csr | KN01_CSR_MEMERR;	/* Clear bus IRQ. */
+	iob();
+
+	raw_spin_unlock_irqrestore(&kn01_lock, flags);
+}
+
+static int dec_kn01_be_backend(struct pt_regs *regs, int is_fixup, int invoker)
+{
+	volatile u32 *kn01_erraddr = (void *)CKSEG1ADDR(KN01_SLOT_BASE +
+							KN01_ERRADDR);
+
+	static const char excstr[] = "exception";
+	static const char intstr[] = "interrupt";
+	static const char cpustr[] = "CPU";
+	static const char mreadstr[] = "memory read";
+	static const char readstr[] = "read";
+	static const char writestr[] = "write";
+	static const char timestr[] = "timeout";
+	static const char paritystr[] = "parity error";
+
+	int data = regs->cp0_cause & 4;
+	unsigned int __user *pc = (unsigned int __user *)regs->cp0_epc +
+				  ((regs->cp0_cause & CAUSEF_BD) != 0);
+	union mips_instruction insn;
+	unsigned long entrylo, offset;
+	long asid, entryhi, vaddr;
+
+	const char *kind, *agent, *cycle, *event;
+	unsigned long address;
+
+	u32 erraddr = *kn01_erraddr;
+	int action = MIPS_BE_FATAL;
+
+	/* Ack ASAP, so that any subsequent errors get caught. */
+	dec_kn01_be_ack();
+
+	kind = invoker ? intstr : excstr;
+
+	agent = cpustr;
+
+	if (invoker)
+		address = erraddr;
+	else {
+		/* Bloody hardware doesn't record the address for reads... */
+		if (data) {
+			/* This never faults. */
+			__get_user(insn.word, pc);
+			vaddr = regs->regs[insn.i_format.rs] +
+				insn.i_format.simmediate;
+		} else
+			vaddr = (long)pc;
+		if (KSEGX(vaddr) == CKSEG0 || KSEGX(vaddr) == CKSEG1)
+			address = CPHYSADDR(vaddr);
+		else {
+			/* Peek at what physical address the CPU used. */
+			asid = read_c0_entryhi();
+			entryhi = asid & (PAGE_SIZE - 1);
+			entryhi |= vaddr & ~(PAGE_SIZE - 1);
+			write_c0_entryhi(entryhi);
+			BARRIER;
+			tlb_probe();
+			/* No need to check for presence. */
+			tlb_read();
+			entrylo = read_c0_entrylo0();
+			write_c0_entryhi(asid);
+			offset = vaddr & (PAGE_SIZE - 1);
+			address = (entrylo & ~(PAGE_SIZE - 1)) | offset;
+		}
+	}
+
+	/* Treat low 256MB as memory, high -- as I/O. */
+	if (address < 0x10000000) {
+		cycle = mreadstr;
+		event = paritystr;
+	} else {
+		cycle = invoker ? writestr : readstr;
+		event = timestr;
+	}
+
+	if (is_fixup)
+		action = MIPS_BE_FIXUP;
+
+	if (action != MIPS_BE_FIXUP)
+		printk(KERN_ALERT "Bus error %s: %s %s %s at %#010lx\n",
+			kind, agent, cycle, event, address);
+
+	return action;
+}
+
+int dec_kn01_be_handler(struct pt_regs *regs, int is_fixup)
+{
+	return dec_kn01_be_backend(regs, is_fixup, 0);
+}
+
+irqreturn_t dec_kn01_be_interrupt(int irq, void *dev_id)
+{
+	volatile u16 *csr = (void *)CKSEG1ADDR(KN01_SLOT_BASE + KN01_CSR);
+	struct pt_regs *regs = get_irq_regs();
+	int action;
+
+	if (!(*csr & KN01_CSR_MEMERR))
+		return IRQ_NONE;		/* Must have been video. */
+
+	action = dec_kn01_be_backend(regs, 0, 1);
+
+	if (action == MIPS_BE_DISCARD)
+		return IRQ_HANDLED;
+
+	/*
+	 * FIXME: Find the affected processes and kill them, otherwise
+	 * we must die.
+	 *
+	 * The interrupt is asynchronously delivered thus EPC and RA
+	 * may be irrelevant, but are printed for a reference.
+	 */
+	printk(KERN_ALERT "Fatal bus interrupt, epc == %08lx, ra == %08lx\n",
+	       regs->cp0_epc, regs->regs[31]);
+	die("Unrecoverable bus error", regs);
+}
+
+
+void __init dec_kn01_be_init(void)
+{
+	volatile u16 *csr = (void *)CKSEG1ADDR(KN01_SLOT_BASE + KN01_CSR);
+	unsigned long flags;
+
+	raw_spin_lock_irqsave(&kn01_lock, flags);
+
+	/* Preset write-only bits of the Control Register cache. */
+	cached_kn01_csr = *csr;
+	cached_kn01_csr &= KN01_CSR_STATUS | KN01_CSR_PARDIS | KN01_CSR_TXDIS;
+	cached_kn01_csr |= KN01_CSR_LEDS;
+
+	/* Enable parity error detection. */
+	cached_kn01_csr &= ~KN01_CSR_PARDIS;
+	*csr = cached_kn01_csr;
+	iob();
+
+	raw_spin_unlock_irqrestore(&kn01_lock, flags);
+
+	/* Clear any leftover errors from the firmware. */
+	dec_kn01_be_ack();
+}
diff --git a/arch/mips/dec/kn02-irq.c b/arch/mips/dec/kn02-irq.c
new file mode 100644
index 000000000..7e18de574
--- /dev/null
+++ b/arch/mips/dec/kn02-irq.c
@@ -0,0 +1,75 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *	DECstation 5000/200 (KN02) Control and Status Register
+ *	interrupts.
+ *
+ *	Copyright (c) 2002, 2003, 2005  Maciej W. Rozycki
+ */
+
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <linux/types.h>
+
+#include <asm/dec/kn02.h>
+
+
+/*
+ * Bits 7:0 of the Control Register are write-only -- the
+ * corresponding bits of the Status Register have a different
+ * meaning.  Hence we use a cache.  It speeds up things a bit
+ * as well.
+ *
+ * There is no default value -- it has to be initialized.
+ */
+u32 cached_kn02_csr;
+
+static int kn02_irq_base;
+
+static void unmask_kn02_irq(struct irq_data *d)
+{
+	volatile u32 *csr = (volatile u32 *)CKSEG1ADDR(KN02_SLOT_BASE +
+						       KN02_CSR);
+
+	cached_kn02_csr |= (1 << (d->irq - kn02_irq_base + 16));
+	*csr = cached_kn02_csr;
+}
+
+static void mask_kn02_irq(struct irq_data *d)
+{
+	volatile u32 *csr = (volatile u32 *)CKSEG1ADDR(KN02_SLOT_BASE +
+						       KN02_CSR);
+
+	cached_kn02_csr &= ~(1 << (d->irq - kn02_irq_base + 16));
+	*csr = cached_kn02_csr;
+}
+
+static void ack_kn02_irq(struct irq_data *d)
+{
+	mask_kn02_irq(d);
+	iob();
+}
+
+static struct irq_chip kn02_irq_type = {
+	.name = "KN02-CSR",
+	.irq_ack = ack_kn02_irq,
+	.irq_mask = mask_kn02_irq,
+	.irq_mask_ack = ack_kn02_irq,
+	.irq_unmask = unmask_kn02_irq,
+};
+
+void __init init_kn02_irqs(int base)
+{
+	volatile u32 *csr = (volatile u32 *)CKSEG1ADDR(KN02_SLOT_BASE +
+						       KN02_CSR);
+	int i;
+
+	/* Mask interrupts. */
+	cached_kn02_csr &= ~KN02_CSR_IOINTEN;
+	*csr = cached_kn02_csr;
+	iob();
+
+	for (i = base; i < base + KN02_IRQ_LINES; i++)
+		irq_set_chip_and_handler(i, &kn02_irq_type, handle_level_irq);
+
+	kn02_irq_base = base;
+}
diff --git a/arch/mips/dec/kn02xa-berr.c b/arch/mips/dec/kn02xa-berr.c
new file mode 100644
index 000000000..9699fc4e6
--- /dev/null
+++ b/arch/mips/dec/kn02xa-berr.c
@@ -0,0 +1,135 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *	Bus error event handling code for 5000-series systems equipped
+ *	with parity error detection logic, i.e. DECstation/DECsystem
+ *	5000/120, /125, /133 (KN02-BA), 5000/150 (KN04-BA) and Personal
+ *	DECstation/DECsystem 5000/20, /25, /33 (KN02-CA), 5000/50
+ *	(KN04-CA) systems.
+ *
+ *	Copyright (c) 2005  Maciej W. Rozycki
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+
+#include <asm/addrspace.h>
+#include <asm/cpu-type.h>
+#include <asm/irq_regs.h>
+#include <asm/ptrace.h>
+#include <asm/traps.h>
+
+#include <asm/dec/kn02ca.h>
+#include <asm/dec/kn02xa.h>
+#include <asm/dec/kn05.h>
+
+static inline void dec_kn02xa_be_ack(void)
+{
+	volatile u32 *mer = (void *)CKSEG1ADDR(KN02XA_MER);
+	volatile u32 *mem_intr = (void *)CKSEG1ADDR(KN02XA_MEM_INTR);
+
+	*mer = KN02CA_MER_INTR;		/* Clear errors; keep the ARC IRQ. */
+	*mem_intr = 0;			/* Any write clears the bus IRQ. */
+	iob();
+}
+
+static int dec_kn02xa_be_backend(struct pt_regs *regs, int is_fixup,
+				 int invoker)
+{
+	volatile u32 *kn02xa_mer = (void *)CKSEG1ADDR(KN02XA_MER);
+	volatile u32 *kn02xa_ear = (void *)CKSEG1ADDR(KN02XA_EAR);
+
+	static const char excstr[] = "exception";
+	static const char intstr[] = "interrupt";
+	static const char cpustr[] = "CPU";
+	static const char mreadstr[] = "memory read";
+	static const char readstr[] = "read";
+	static const char writestr[] = "write";
+	static const char timestr[] = "timeout";
+	static const char paritystr[] = "parity error";
+	static const char lanestat[][4] = { " OK", "BAD" };
+
+	const char *kind, *agent, *cycle, *event;
+	unsigned long address;
+
+	u32 mer = *kn02xa_mer;
+	u32 ear = *kn02xa_ear;
+	int action = MIPS_BE_FATAL;
+
+	/* Ack ASAP, so that any subsequent errors get caught. */
+	dec_kn02xa_be_ack();
+
+	kind = invoker ? intstr : excstr;
+
+	/* No DMA errors? */
+	agent = cpustr;
+
+	address = ear & KN02XA_EAR_ADDRESS;
+
+	/* Low 256MB is decoded as memory, high -- as TC. */
+	if (address < 0x10000000) {
+		cycle = mreadstr;
+		event = paritystr;
+	} else {
+		cycle = invoker ? writestr : readstr;
+		event = timestr;
+	}
+
+	if (is_fixup)
+		action = MIPS_BE_FIXUP;
+
+	if (action != MIPS_BE_FIXUP)
+		printk(KERN_ALERT "Bus error %s: %s %s %s at %#010lx\n",
+			kind, agent, cycle, event, address);
+
+	if (action != MIPS_BE_FIXUP && address < 0x10000000)
+		printk(KERN_ALERT "  Byte lane status %#3x -- "
+		       "#3: %s, #2: %s, #1: %s, #0: %s\n",
+		       (mer & KN02XA_MER_BYTERR) >> 8,
+		       lanestat[(mer & KN02XA_MER_BYTERR_3) != 0],
+		       lanestat[(mer & KN02XA_MER_BYTERR_2) != 0],
+		       lanestat[(mer & KN02XA_MER_BYTERR_1) != 0],
+		       lanestat[(mer & KN02XA_MER_BYTERR_0) != 0]);
+
+	return action;
+}
+
+int dec_kn02xa_be_handler(struct pt_regs *regs, int is_fixup)
+{
+	return dec_kn02xa_be_backend(regs, is_fixup, 0);
+}
+
+irqreturn_t dec_kn02xa_be_interrupt(int irq, void *dev_id)
+{
+	struct pt_regs *regs = get_irq_regs();
+	int action = dec_kn02xa_be_backend(regs, 0, 1);
+
+	if (action == MIPS_BE_DISCARD)
+		return IRQ_HANDLED;
+
+	/*
+	 * FIXME: Find the affected processes and kill them, otherwise
+	 * we must die.
+	 *
+	 * The interrupt is asynchronously delivered thus EPC and RA
+	 * may be irrelevant, but are printed for a reference.
+	 */
+	printk(KERN_ALERT "Fatal bus interrupt, epc == %08lx, ra == %08lx\n",
+	       regs->cp0_epc, regs->regs[31]);
+	die("Unrecoverable bus error", regs);
+}
+
+
+void __init dec_kn02xa_be_init(void)
+{
+	volatile u32 *mbcs = (void *)CKSEG1ADDR(KN4K_SLOT_BASE + KN4K_MB_CSR);
+
+	/* For KN04 we need to make sure EE (?) is enabled in the MB.  */
+	if (current_cpu_type() == CPU_R4000SC)
+		*mbcs |= KN4K_MB_CSR_EE;
+	fast_iob();
+
+	/* Clear any leftover errors from the firmware. */
+	dec_kn02xa_be_ack();
+}
diff --git a/arch/mips/dec/platform.c b/arch/mips/dec/platform.c
new file mode 100644
index 000000000..c4fcb8c58
--- /dev/null
+++ b/arch/mips/dec/platform.c
@@ -0,0 +1,40 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *	DEC platform devices.
+ *
+ *	Copyright (c) 2014  Maciej W. Rozycki
+ */
+
+#include <linux/ioport.h>
+#include <linux/kernel.h>
+#include <linux/mc146818rtc.h>
+#include <linux/platform_device.h>
+
+static struct resource dec_rtc_resources[] = {
+	{
+		.name = "rtc",
+		.flags = IORESOURCE_MEM,
+	},
+};
+
+static struct cmos_rtc_board_info dec_rtc_info = {
+	.flags = CMOS_RTC_FLAGS_NOFREQ,
+	.address_space = 64,
+};
+
+static struct platform_device dec_rtc_device = {
+	.name = "rtc_cmos",
+	.id = PLATFORM_DEVID_NONE,
+	.dev.platform_data = &dec_rtc_info,
+	.resource = dec_rtc_resources,
+	.num_resources = ARRAY_SIZE(dec_rtc_resources),
+};
+
+static int __init dec_add_devices(void)
+{
+	dec_rtc_resources[0].start = RTC_PORT(0);
+	dec_rtc_resources[0].end = RTC_PORT(0) + dec_kn_slot_size - 1;
+	return platform_device_register(&dec_rtc_device);
+}
+
+device_initcall(dec_add_devices);
diff --git a/arch/mips/dec/prom/Makefile b/arch/mips/dec/prom/Makefile
new file mode 100644
index 000000000..2bad87551
--- /dev/null
+++ b/arch/mips/dec/prom/Makefile
@@ -0,0 +1,9 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Makefile for the DECstation prom monitor library routines
+# under Linux.
+#
+
+lib-y			+= init.o memory.o cmdline.o identify.o console.o
+
+lib-$(CONFIG_CPU_R3000)	+= locore.o
diff --git a/arch/mips/dec/prom/cmdline.c b/arch/mips/dec/prom/cmdline.c
new file mode 100644
index 000000000..3ed63280a
--- /dev/null
+++ b/arch/mips/dec/prom/cmdline.c
@@ -0,0 +1,40 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * cmdline.c: read the command line passed to us by the PROM.
+ *
+ * Copyright (C) 1998 Harald Koerfgen
+ * Copyright (C) 2002, 2004  Maciej W. Rozycki
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <linux/types.h>
+
+#include <asm/bootinfo.h>
+#include <asm/dec/prom.h>
+
+#undef PROM_DEBUG
+
+void __init prom_init_cmdline(s32 argc, s32 *argv, u32 magic)
+{
+	char *arg;
+	int start_arg, i;
+
+	/*
+	 * collect args and prepare cmd_line
+	 */
+	if (!prom_is_rex(magic))
+		start_arg = 1;
+	else
+		start_arg = 2;
+	for (i = start_arg; i < argc; i++) {
+		arg = (void *)(long)(argv[i]);
+		strcat(arcs_cmdline, arg);
+		if (i < (argc - 1))
+			strcat(arcs_cmdline, " ");
+	}
+
+#ifdef PROM_DEBUG
+	printk("arcs_cmdline: %s\n", &(arcs_cmdline[0]));
+#endif
+}
diff --git a/arch/mips/dec/prom/console.c b/arch/mips/dec/prom/console.c
new file mode 100644
index 000000000..31a8441d8
--- /dev/null
+++ b/arch/mips/dec/prom/console.c
@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *	DECstation PROM-based early console support.
+ *
+ *	Copyright (C) 2004, 2007  Maciej W. Rozycki
+ */
+#include <linux/console.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/string.h>
+
+#include <asm/dec/prom.h>
+
+static void __init prom_console_write(struct console *con, const char *s,
+				      unsigned int c)
+{
+	char buf[81];
+	unsigned int chunk = sizeof(buf) - 1;
+
+	while (c > 0) {
+		if (chunk > c)
+			chunk = c;
+		memcpy(buf, s, chunk);
+		buf[chunk] = '\0';
+		prom_printf("%s", buf);
+		s += chunk;
+		c -= chunk;
+	}
+}
+
+static struct console promcons __initdata = {
+	.name	= "prom",
+	.write	= prom_console_write,
+	.flags	= CON_BOOT | CON_PRINTBUFFER,
+	.index	= -1,
+};
+
+void __init register_prom_console(void)
+{
+	register_console(&promcons);
+}
diff --git a/arch/mips/dec/prom/dectypes.h b/arch/mips/dec/prom/dectypes.h
new file mode 100644
index 000000000..9fcbcc7cd
--- /dev/null
+++ b/arch/mips/dec/prom/dectypes.h
@@ -0,0 +1,15 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef DECTYPES
+#define DECTYPES
+
+#define DS2100_3100	1	/* DS2100/3100	Pmax		*/
+#define DS5000_200	2	/* DS5000/200	3max		*/
+#define DS5000_1XX	3	/* DS5000/1xx	kmin		*/
+#define DS5000_2X0	4	/* DS5000/2x0	3max+		*/
+#define DS5800		5	/* DS5800	Isis		*/
+#define DS5400		6	/* DS5400	MIPSfair	*/
+#define DS5000_XX	7	/* DS5000/xx	maxine		*/
+#define DS5500		11	/* DS5500	MIPSfair-2	*/
+#define DS5100		12	/* DS5100	MIPSmate	*/
+
+#endif
diff --git a/arch/mips/dec/prom/identify.c b/arch/mips/dec/prom/identify.c
new file mode 100644
index 000000000..80cd14cd1
--- /dev/null
+++ b/arch/mips/dec/prom/identify.c
@@ -0,0 +1,187 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * identify.c: machine identification code.
+ *
+ * Copyright (C) 1998 Harald Koerfgen and Paul M. Antoine
+ * Copyright (C) 2002, 2003, 2004, 2005  Maciej W. Rozycki
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/mc146818rtc.h>
+#include <linux/export.h>
+#include <linux/string.h>
+#include <linux/types.h>
+
+#include <asm/bootinfo.h>
+
+#include <asm/dec/ioasic.h>
+#include <asm/dec/ioasic_addrs.h>
+#include <asm/dec/kn01.h>
+#include <asm/dec/kn02.h>
+#include <asm/dec/kn02ba.h>
+#include <asm/dec/kn02ca.h>
+#include <asm/dec/kn03.h>
+#include <asm/dec/kn230.h>
+#include <asm/dec/prom.h>
+#include <asm/dec/system.h>
+
+#include "dectypes.h"
+
+static const char *dec_system_strings[] = {
+	[MACH_DSUNKNOWN]	"unknown DECstation",
+	[MACH_DS23100]		"DECstation 2100/3100",
+	[MACH_DS5100]		"DECsystem 5100",
+	[MACH_DS5000_200]	"DECstation 5000/200",
+	[MACH_DS5000_1XX]	"DECstation 5000/1xx",
+	[MACH_DS5000_XX]	"Personal DECstation 5000/xx",
+	[MACH_DS5000_2X0]	"DECstation 5000/2x0",
+	[MACH_DS5400]		"DECsystem 5400",
+	[MACH_DS5500]		"DECsystem 5500",
+	[MACH_DS5800]		"DECsystem 5800",
+	[MACH_DS5900]		"DECsystem 5900",
+};
+
+const char *get_system_type(void)
+{
+#define STR_BUF_LEN	64
+	static char system[STR_BUF_LEN];
+	static int called = 0;
+
+	if (called == 0) {
+		called = 1;
+		snprintf(system, STR_BUF_LEN, "Digital %s",
+			 dec_system_strings[mips_machtype]);
+	}
+
+	return system;
+}
+
+
+/*
+ * Setup essential system-specific memory addresses.  We need them
+ * early.  Semantically the functions belong to prom/init.c, but they
+ * are compact enough we want them inlined. --macro
+ */
+volatile u8 *dec_rtc_base;
+
+EXPORT_SYMBOL(dec_rtc_base);
+
+static inline void prom_init_kn01(void)
+{
+	dec_kn_slot_base = KN01_SLOT_BASE;
+	dec_kn_slot_size = KN01_SLOT_SIZE;
+
+	dec_rtc_base = (void *)CKSEG1ADDR(dec_kn_slot_base + KN01_RTC);
+}
+
+static inline void prom_init_kn230(void)
+{
+	dec_kn_slot_base = KN01_SLOT_BASE;
+	dec_kn_slot_size = KN01_SLOT_SIZE;
+
+	dec_rtc_base = (void *)CKSEG1ADDR(dec_kn_slot_base + KN01_RTC);
+}
+
+static inline void prom_init_kn02(void)
+{
+	dec_kn_slot_base = KN02_SLOT_BASE;
+	dec_kn_slot_size = KN02_SLOT_SIZE;
+	dec_tc_bus = 1;
+
+	dec_rtc_base = (void *)CKSEG1ADDR(dec_kn_slot_base + KN02_RTC);
+}
+
+static inline void prom_init_kn02xa(void)
+{
+	dec_kn_slot_base = KN02XA_SLOT_BASE;
+	dec_kn_slot_size = IOASIC_SLOT_SIZE;
+	dec_tc_bus = 1;
+
+	ioasic_base = (void *)CKSEG1ADDR(dec_kn_slot_base + IOASIC_IOCTL);
+	dec_rtc_base = (void *)CKSEG1ADDR(dec_kn_slot_base + IOASIC_TOY);
+}
+
+static inline void prom_init_kn03(void)
+{
+	dec_kn_slot_base = KN03_SLOT_BASE;
+	dec_kn_slot_size = IOASIC_SLOT_SIZE;
+	dec_tc_bus = 1;
+
+	ioasic_base = (void *)CKSEG1ADDR(dec_kn_slot_base + IOASIC_IOCTL);
+	dec_rtc_base = (void *)CKSEG1ADDR(dec_kn_slot_base + IOASIC_TOY);
+}
+
+
+void __init prom_identify_arch(u32 magic)
+{
+	unsigned char dec_cpunum, dec_firmrev, dec_etc, dec_systype;
+	u32 dec_sysid;
+
+	if (!prom_is_rex(magic)) {
+		dec_sysid = simple_strtoul(prom_getenv("systype"),
+					   (char **)0, 0);
+	} else {
+		dec_sysid = rex_getsysid();
+		if (dec_sysid == 0) {
+			printk("Zero sysid returned from PROM! "
+			       "Assuming a PMAX-like machine.\n");
+			dec_sysid = 1;
+		}
+	}
+
+	dec_cpunum = (dec_sysid & 0xff000000) >> 24;
+	dec_systype = (dec_sysid & 0xff0000) >> 16;
+	dec_firmrev = (dec_sysid & 0xff00) >> 8;
+	dec_etc = dec_sysid & 0xff;
+
+	/*
+	 * FIXME: This may not be an exhaustive list of DECStations/Servers!
+	 * Put all model-specific initialisation calls here.
+	 */
+	switch (dec_systype) {
+	case DS2100_3100:
+		mips_machtype = MACH_DS23100;
+		prom_init_kn01();
+		break;
+	case DS5100:		/* DS5100 MIPSMATE */
+		mips_machtype = MACH_DS5100;
+		prom_init_kn230();
+		break;
+	case DS5000_200:	/* DS5000 3max */
+		mips_machtype = MACH_DS5000_200;
+		prom_init_kn02();
+		break;
+	case DS5000_1XX:	/* DS5000/100 3min */
+		mips_machtype = MACH_DS5000_1XX;
+		prom_init_kn02xa();
+		break;
+	case DS5000_2X0:	/* DS5000/240 3max+ or DS5900 bigmax */
+		mips_machtype = MACH_DS5000_2X0;
+		prom_init_kn03();
+		if (!(ioasic_read(IO_REG_SIR) & KN03_IO_INR_3MAXP))
+			mips_machtype = MACH_DS5900;
+		break;
+	case DS5000_XX:		/* Personal DS5000/xx maxine */
+		mips_machtype = MACH_DS5000_XX;
+		prom_init_kn02xa();
+		break;
+	case DS5800:		/* DS5800 Isis */
+		mips_machtype = MACH_DS5800;
+		break;
+	case DS5400:		/* DS5400 MIPSfair */
+		mips_machtype = MACH_DS5400;
+		break;
+	case DS5500:		/* DS5500 MIPSfair-2 */
+		mips_machtype = MACH_DS5500;
+		break;
+	default:
+		mips_machtype = MACH_DSUNKNOWN;
+		break;
+	}
+
+	if (mips_machtype == MACH_DSUNKNOWN)
+		printk("This is an %s, id is %x\n",
+		       dec_system_strings[mips_machtype], dec_systype);
+	else
+		printk("This is a %s\n", dec_system_strings[mips_machtype]);
+}
diff --git a/arch/mips/dec/prom/init.c b/arch/mips/dec/prom/init.c
new file mode 100644
index 000000000..cb12eb211
--- /dev/null
+++ b/arch/mips/dec/prom/init.c
@@ -0,0 +1,137 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * init.c: PROM library initialisation code.
+ *
+ * Copyright (C) 1998 Harald Koerfgen
+ * Copyright (C) 2002, 2004  Maciej W. Rozycki
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/linkage.h>
+#include <linux/smp.h>
+#include <linux/string.h>
+#include <linux/types.h>
+
+#include <asm/bootinfo.h>
+#include <asm/cpu.h>
+#include <asm/cpu-type.h>
+#include <asm/processor.h>
+
+#include <asm/dec/prom.h>
+
+
+int (*__rex_bootinit)(void);
+int (*__rex_bootread)(void);
+int (*__rex_getbitmap)(memmap *);
+unsigned long *(*__rex_slot_address)(int);
+void *(*__rex_gettcinfo)(void);
+int (*__rex_getsysid)(void);
+void (*__rex_clear_cache)(void);
+
+int (*__prom_getchar)(void);
+char *(*__prom_getenv)(char *);
+int (*__prom_printf)(char *, ...);
+
+int (*__pmax_open)(char*, int);
+int (*__pmax_lseek)(int, long, int);
+int (*__pmax_read)(int, void *, int);
+int (*__pmax_close)(int);
+
+
+/*
+ * Detect which PROM the DECSTATION has, and set the callback vectors
+ * appropriately.
+ */
+void __init which_prom(s32 magic, s32 *prom_vec)
+{
+	/*
+	 * No sign of the REX PROM's magic number means we assume a non-REX
+	 * machine (i.e. we're on a DS2100/3100, DS5100 or DS5000/2xx)
+	 */
+	if (prom_is_rex(magic)) {
+		/*
+		 * Set up prom abstraction structure with REX entry points.
+		 */
+		__rex_bootinit =
+			(void *)(long)*(prom_vec + REX_PROM_BOOTINIT);
+		__rex_bootread =
+			(void *)(long)*(prom_vec + REX_PROM_BOOTREAD);
+		__rex_getbitmap =
+			(void *)(long)*(prom_vec + REX_PROM_GETBITMAP);
+		__prom_getchar =
+			(void *)(long)*(prom_vec + REX_PROM_GETCHAR);
+		__prom_getenv =
+			(void *)(long)*(prom_vec + REX_PROM_GETENV);
+		__rex_getsysid =
+			(void *)(long)*(prom_vec + REX_PROM_GETSYSID);
+		__rex_gettcinfo =
+			(void *)(long)*(prom_vec + REX_PROM_GETTCINFO);
+		__prom_printf =
+			(void *)(long)*(prom_vec + REX_PROM_PRINTF);
+		__rex_slot_address =
+			(void *)(long)*(prom_vec + REX_PROM_SLOTADDR);
+		__rex_clear_cache =
+			(void *)(long)*(prom_vec + REX_PROM_CLEARCACHE);
+	} else {
+		/*
+		 * Set up prom abstraction structure with non-REX entry points.
+		 */
+		__prom_getchar = (void *)PMAX_PROM_GETCHAR;
+		__prom_getenv = (void *)PMAX_PROM_GETENV;
+		__prom_printf = (void *)PMAX_PROM_PRINTF;
+		__pmax_open = (void *)PMAX_PROM_OPEN;
+		__pmax_lseek = (void *)PMAX_PROM_LSEEK;
+		__pmax_read = (void *)PMAX_PROM_READ;
+		__pmax_close = (void *)PMAX_PROM_CLOSE;
+	}
+}
+
+void __init prom_init(void)
+{
+	extern void dec_machine_halt(void);
+	static const char cpu_msg[] __initconst =
+		"Sorry, this kernel is compiled for a wrong CPU type!\n";
+	s32 argc = fw_arg0;
+	s32 *argv = (void *)fw_arg1;
+	u32 magic = fw_arg2;
+	s32 *prom_vec = (void *)fw_arg3;
+
+	/*
+	 * Determine which PROM we have
+	 * (and therefore which machine we're on!)
+	 */
+	which_prom(magic, prom_vec);
+
+	if (prom_is_rex(magic))
+		rex_clear_cache();
+
+	/* Register the early console.  */
+	register_prom_console();
+
+	/* Were we compiled with the right CPU option? */
+#if defined(CONFIG_CPU_R3000)
+	if ((current_cpu_type() == CPU_R4000SC) ||
+	    (current_cpu_type() == CPU_R4400SC)) {
+		static const char r4k_msg[] __initconst =
+			"Please recompile with \"CONFIG_CPU_R4X00 = y\".\n";
+		printk(cpu_msg);
+		printk(r4k_msg);
+		dec_machine_halt();
+	}
+#endif
+
+#if defined(CONFIG_CPU_R4X00)
+	if ((current_cpu_type() == CPU_R3000) ||
+	    (current_cpu_type() == CPU_R3000A)) {
+		static const char r3k_msg[] __initconst =
+			"Please recompile with \"CONFIG_CPU_R3000 = y\".\n";
+		printk(cpu_msg);
+		printk(r3k_msg);
+		dec_machine_halt();
+	}
+#endif
+
+	prom_meminit(magic);
+	prom_identify_arch(magic);
+	prom_init_cmdline(argc, argv, magic);
+}
diff --git a/arch/mips/dec/prom/locore.S b/arch/mips/dec/prom/locore.S
new file mode 100644
index 000000000..0eb8fab62
--- /dev/null
+++ b/arch/mips/dec/prom/locore.S
@@ -0,0 +1,30 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * locore.S
+ */
+#include <asm/asm.h>
+#include <asm/regdef.h>
+#include <asm/mipsregs.h>
+
+	.text
+
+/*
+ * Simple general exception handling routine. This one is used for the
+ * Memory sizing routine for pmax machines. HK
+ */
+
+NESTED(genexcept_early, 0, sp)
+	.set	noat
+	.set	noreorder
+
+	mfc0	k0, CP0_STATUS
+	la	k1, mem_err
+
+	sw	k0, 0(k1)
+
+	mfc0	k0, CP0_EPC
+	nop
+	addiu	k0, 4		# skip the causing instruction
+	jr	k0
+	 rfe
+END(genexcept_early)
diff --git a/arch/mips/dec/prom/memory.c b/arch/mips/dec/prom/memory.c
new file mode 100644
index 000000000..44490c30d
--- /dev/null
+++ b/arch/mips/dec/prom/memory.c
@@ -0,0 +1,117 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * memory.c: memory initialisation code.
+ *
+ * Copyright (C) 1998 Harald Koerfgen, Frieder Streffer and Paul M. Antoine
+ * Copyright (C) 2000, 2002  Maciej W. Rozycki
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/mm.h>
+#include <linux/memblock.h>
+#include <linux/types.h>
+
+#include <asm/addrspace.h>
+#include <asm/dec/machtype.h>
+#include <asm/dec/prom.h>
+#include <asm/page.h>
+#include <asm/sections.h>
+
+
+volatile unsigned long mem_err;		/* So we know an error occurred */
+
+/*
+ * Probe memory in 4MB chunks, waiting for an error to tell us we've fallen
+ * off the end of real memory.  Only suitable for the 2100/3100's (PMAX).
+ */
+
+#define CHUNK_SIZE 0x400000
+
+static __init void pmax_setup_memory_region(void)
+{
+	volatile unsigned char *memory_page, dummy;
+	char old_handler[0x80];
+	extern char genexcept_early;
+
+	/* Install exception handler */
+	memcpy(&old_handler, (void *)(CKSEG0 + 0x80), 0x80);
+	memcpy((void *)(CKSEG0 + 0x80), &genexcept_early, 0x80);
+
+	/* read unmapped and uncached (KSEG1)
+	 * DECstations have at least 4MB RAM
+	 * Assume less than 480MB of RAM, as this is max for 5000/2xx
+	 * FIXME this should be replaced by the first free page!
+	 */
+	for (memory_page = (unsigned char *)CKSEG1 + CHUNK_SIZE;
+	     mem_err == 0 && memory_page < (unsigned char *)CKSEG1 + 0x1e00000;
+	     memory_page += CHUNK_SIZE) {
+		dummy = *memory_page;
+	}
+	memcpy((void *)(CKSEG0 + 0x80), &old_handler, 0x80);
+
+	memblock_add(0, (unsigned long)memory_page - CKSEG1 - CHUNK_SIZE);
+}
+
+/*
+ * Use the REX prom calls to get hold of the memory bitmap, and thence
+ * determine memory size.
+ */
+static __init void rex_setup_memory_region(void)
+{
+	int i, bitmap_size;
+	unsigned long mem_start = 0, mem_size = 0;
+	memmap *bm;
+
+	/* some free 64k */
+	bm = (memmap *)CKSEG0ADDR(0x28000);
+
+	bitmap_size = rex_getbitmap(bm);
+
+	for (i = 0; i < bitmap_size; i++) {
+		/* FIXME: very simplistically only add full sets of pages */
+		if (bm->bitmap[i] == 0xff)
+			mem_size += (8 * bm->pagesize);
+		else if (!mem_size)
+			mem_start += (8 * bm->pagesize);
+		else {
+			memblock_add(mem_start, mem_size);
+			mem_start += mem_size + (8 * bm->pagesize);
+			mem_size = 0;
+		}
+	}
+	if (mem_size)
+		memblock_add(mem_start, mem_size);
+}
+
+void __init prom_meminit(u32 magic)
+{
+	if (!prom_is_rex(magic))
+		pmax_setup_memory_region();
+	else
+		rex_setup_memory_region();
+}
+
+void __init prom_free_prom_memory(void)
+{
+	unsigned long end;
+
+	/*
+	 * Free everything below the kernel itself but leave
+	 * the first page reserved for the exception handlers.
+	 */
+
+#if IS_ENABLED(CONFIG_DECLANCE)
+	/*
+	 * Leave 128 KB reserved for Lance memory for
+	 * IOASIC DECstations.
+	 *
+	 * XXX: save this address for use in dec_lance.c?
+	 */
+	if (IOASIC)
+		end = __pa(&_text) - 0x00020000;
+	else
+#endif
+		end = __pa(&_text);
+
+	free_init_pages("unused PROM memory", PAGE_SIZE, end);
+}
diff --git a/arch/mips/dec/reset.c b/arch/mips/dec/reset.c
new file mode 100644
index 000000000..3df01f1da
--- /dev/null
+++ b/arch/mips/dec/reset.c
@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Reset a DECstation machine.
+ *
+ * Copyright (C) 199x  the Anonymous
+ * Copyright (C) 2001, 2002, 2003  Maciej W. Rozycki
+ */
+#include <linux/interrupt.h>
+#include <linux/linkage.h>
+
+#include <asm/addrspace.h>
+
+typedef void __noreturn (* noret_func_t)(void);
+
+static inline void __noreturn back_to_prom(void)
+{
+	noret_func_t func = (void *)CKSEG1ADDR(0x1fc00000);
+
+	func();
+}
+
+void __noreturn dec_machine_restart(char *command)
+{
+	back_to_prom();
+}
+
+void __noreturn dec_machine_halt(void)
+{
+	back_to_prom();
+}
+
+void __noreturn dec_machine_power_off(void)
+{
+    /* DECstations don't have a software power switch */
+	back_to_prom();
+}
+
+irqreturn_t dec_intr_halt(int irq, void *dev_id)
+{
+	dec_machine_halt();
+}
diff --git a/arch/mips/dec/setup.c b/arch/mips/dec/setup.c
new file mode 100644
index 000000000..6c3704f51
--- /dev/null
+++ b/arch/mips/dec/setup.c
@@ -0,0 +1,784 @@
+/*
+ * System-specific setup, especially interrupts.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1998 Harald Koerfgen
+ * Copyright (C) 2000, 2001, 2002, 2003, 2005, 2020  Maciej W. Rozycki
+ */
+#include <linux/console.h>
+#include <linux/export.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/irq.h>
+#include <linux/irqnr.h>
+#include <linux/memblock.h>
+#include <linux/param.h>
+#include <linux/percpu-defs.h>
+#include <linux/sched.h>
+#include <linux/spinlock.h>
+#include <linux/types.h>
+#include <linux/pm.h>
+
+#include <asm/addrspace.h>
+#include <asm/bootinfo.h>
+#include <asm/cpu.h>
+#include <asm/cpu-features.h>
+#include <asm/cpu-type.h>
+#include <asm/irq.h>
+#include <asm/irq_cpu.h>
+#include <asm/mipsregs.h>
+#include <asm/page.h>
+#include <asm/reboot.h>
+#include <asm/sections.h>
+#include <asm/time.h>
+#include <asm/traps.h>
+#include <asm/wbflush.h>
+
+#include <asm/dec/interrupts.h>
+#include <asm/dec/ioasic.h>
+#include <asm/dec/ioasic_addrs.h>
+#include <asm/dec/ioasic_ints.h>
+#include <asm/dec/kn01.h>
+#include <asm/dec/kn02.h>
+#include <asm/dec/kn02ba.h>
+#include <asm/dec/kn02ca.h>
+#include <asm/dec/kn03.h>
+#include <asm/dec/kn230.h>
+#include <asm/dec/system.h>
+
+
+extern void dec_machine_restart(char *command);
+extern void dec_machine_halt(void);
+extern void dec_machine_power_off(void);
+extern irqreturn_t dec_intr_halt(int irq, void *dev_id);
+
+unsigned long dec_kn_slot_base, dec_kn_slot_size;
+
+EXPORT_SYMBOL(dec_kn_slot_base);
+EXPORT_SYMBOL(dec_kn_slot_size);
+
+int dec_tc_bus;
+
+DEFINE_SPINLOCK(ioasic_ssr_lock);
+EXPORT_SYMBOL(ioasic_ssr_lock);
+
+volatile u32 *ioasic_base;
+
+EXPORT_SYMBOL(ioasic_base);
+
+/*
+ * IRQ routing and priority tables.  Priorities are set as follows:
+ *
+ *		KN01	KN230	KN02	KN02-BA	KN02-CA	KN03
+ *
+ * MEMORY	CPU	CPU	CPU	ASIC	CPU	CPU
+ * RTC		CPU	CPU	CPU	ASIC	CPU	CPU
+ * DMA		-	-	-	ASIC	ASIC	ASIC
+ * SERIAL0	CPU	CPU	CSR	ASIC	ASIC	ASIC
+ * SERIAL1	-	-	-	ASIC	-	ASIC
+ * SCSI		CPU	CPU	CSR	ASIC	ASIC	ASIC
+ * ETHERNET	CPU	*	CSR	ASIC	ASIC	ASIC
+ * other	-	-	-	ASIC	-	-
+ * TC2		-	-	CSR	CPU	ASIC	ASIC
+ * TC1		-	-	CSR	CPU	ASIC	ASIC
+ * TC0		-	-	CSR	CPU	ASIC	ASIC
+ * other	-	CPU	-	CPU	ASIC	ASIC
+ * other	-	-	-	-	CPU	CPU
+ *
+ * * -- shared with SCSI
+ */
+
+int dec_interrupt[DEC_NR_INTS] = {
+	[0 ... DEC_NR_INTS - 1] = -1
+};
+
+EXPORT_SYMBOL(dec_interrupt);
+
+int_ptr cpu_mask_nr_tbl[DEC_MAX_CPU_INTS][2] = {
+	{ { .i = ~0 }, { .p = dec_intr_unimplemented } },
+};
+int_ptr asic_mask_nr_tbl[DEC_MAX_ASIC_INTS][2] = {
+	{ { .i = ~0 }, { .p = asic_intr_unimplemented } },
+};
+int cpu_fpu_mask = DEC_CPU_IRQ_MASK(DEC_CPU_INR_FPU);
+int *fpu_kstat_irq;
+
+static irq_handler_t busirq_handler;
+static unsigned int busirq_flags = IRQF_NO_THREAD;
+
+/*
+ * Bus error (DBE/IBE exceptions and bus interrupts) handling setup.
+ */
+static void __init dec_be_init(void)
+{
+	switch (mips_machtype) {
+	case MACH_DS23100:	/* DS2100/DS3100 Pmin/Pmax */
+		mips_set_be_handler(dec_kn01_be_handler);
+		busirq_handler = dec_kn01_be_interrupt;
+		busirq_flags |= IRQF_SHARED;
+		dec_kn01_be_init();
+		break;
+	case MACH_DS5000_1XX:	/* DS5000/1xx 3min */
+	case MACH_DS5000_XX:	/* DS5000/xx Maxine */
+		mips_set_be_handler(dec_kn02xa_be_handler);
+		busirq_handler = dec_kn02xa_be_interrupt;
+		dec_kn02xa_be_init();
+		break;
+	case MACH_DS5000_200:	/* DS5000/200 3max */
+	case MACH_DS5000_2X0:	/* DS5000/240 3max+ */
+	case MACH_DS5900:	/* DS5900 bigmax */
+		mips_set_be_handler(dec_ecc_be_handler);
+		busirq_handler = dec_ecc_be_interrupt;
+		dec_ecc_be_init();
+		break;
+	}
+}
+
+void __init plat_mem_setup(void)
+{
+	board_be_init = dec_be_init;
+
+	wbflush_setup();
+
+	_machine_restart = dec_machine_restart;
+	_machine_halt = dec_machine_halt;
+	pm_power_off = dec_machine_power_off;
+
+	ioport_resource.start = ~0UL;
+	ioport_resource.end = 0UL;
+
+	/* Stay away from the firmware working memory area for now. */
+	memblock_reserve(PHYS_OFFSET, __pa_symbol(&_text) - PHYS_OFFSET);
+}
+
+/*
+ * Machine-specific initialisation for KN01, aka DS2100 (aka Pmin)
+ * or DS3100 (aka Pmax).
+ */
+static int kn01_interrupt[DEC_NR_INTS] __initdata = {
+	[DEC_IRQ_CASCADE]	= -1,
+	[DEC_IRQ_AB_RECV]	= -1,
+	[DEC_IRQ_AB_XMIT]	= -1,
+	[DEC_IRQ_DZ11]		= DEC_CPU_IRQ_NR(KN01_CPU_INR_DZ11),
+	[DEC_IRQ_ASC]		= -1,
+	[DEC_IRQ_FLOPPY]	= -1,
+	[DEC_IRQ_FPU]		= DEC_CPU_IRQ_NR(DEC_CPU_INR_FPU),
+	[DEC_IRQ_HALT]		= -1,
+	[DEC_IRQ_ISDN]		= -1,
+	[DEC_IRQ_LANCE]		= DEC_CPU_IRQ_NR(KN01_CPU_INR_LANCE),
+	[DEC_IRQ_BUS]		= DEC_CPU_IRQ_NR(KN01_CPU_INR_BUS),
+	[DEC_IRQ_PSU]		= -1,
+	[DEC_IRQ_RTC]		= DEC_CPU_IRQ_NR(KN01_CPU_INR_RTC),
+	[DEC_IRQ_SCC0]		= -1,
+	[DEC_IRQ_SCC1]		= -1,
+	[DEC_IRQ_SII]		= DEC_CPU_IRQ_NR(KN01_CPU_INR_SII),
+	[DEC_IRQ_TC0]		= -1,
+	[DEC_IRQ_TC1]		= -1,
+	[DEC_IRQ_TC2]		= -1,
+	[DEC_IRQ_TIMER]		= -1,
+	[DEC_IRQ_VIDEO]		= DEC_CPU_IRQ_NR(KN01_CPU_INR_VIDEO),
+	[DEC_IRQ_ASC_MERR]	= -1,
+	[DEC_IRQ_ASC_ERR]	= -1,
+	[DEC_IRQ_ASC_DMA]	= -1,
+	[DEC_IRQ_FLOPPY_ERR]	= -1,
+	[DEC_IRQ_ISDN_ERR]	= -1,
+	[DEC_IRQ_ISDN_RXDMA]	= -1,
+	[DEC_IRQ_ISDN_TXDMA]	= -1,
+	[DEC_IRQ_LANCE_MERR]	= -1,
+	[DEC_IRQ_SCC0A_RXERR]	= -1,
+	[DEC_IRQ_SCC0A_RXDMA]	= -1,
+	[DEC_IRQ_SCC0A_TXERR]	= -1,
+	[DEC_IRQ_SCC0A_TXDMA]	= -1,
+	[DEC_IRQ_AB_RXERR]	= -1,
+	[DEC_IRQ_AB_RXDMA]	= -1,
+	[DEC_IRQ_AB_TXERR]	= -1,
+	[DEC_IRQ_AB_TXDMA]	= -1,
+	[DEC_IRQ_SCC1A_RXERR]	= -1,
+	[DEC_IRQ_SCC1A_RXDMA]	= -1,
+	[DEC_IRQ_SCC1A_TXERR]	= -1,
+	[DEC_IRQ_SCC1A_TXDMA]	= -1,
+};
+
+static int_ptr kn01_cpu_mask_nr_tbl[][2] __initdata = {
+	{ { .i = DEC_CPU_IRQ_MASK(KN01_CPU_INR_BUS) },
+		{ .i = DEC_CPU_IRQ_NR(KN01_CPU_INR_BUS) } },
+	{ { .i = DEC_CPU_IRQ_MASK(KN01_CPU_INR_RTC) },
+		{ .i = DEC_CPU_IRQ_NR(KN01_CPU_INR_RTC) } },
+	{ { .i = DEC_CPU_IRQ_MASK(KN01_CPU_INR_DZ11) },
+		{ .i = DEC_CPU_IRQ_NR(KN01_CPU_INR_DZ11) } },
+	{ { .i = DEC_CPU_IRQ_MASK(KN01_CPU_INR_SII) },
+		{ .i = DEC_CPU_IRQ_NR(KN01_CPU_INR_SII) } },
+	{ { .i = DEC_CPU_IRQ_MASK(KN01_CPU_INR_LANCE) },
+		{ .i = DEC_CPU_IRQ_NR(KN01_CPU_INR_LANCE) } },
+	{ { .i = DEC_CPU_IRQ_ALL },
+		{ .p = cpu_all_int } },
+};
+
+static void __init dec_init_kn01(void)
+{
+	/* IRQ routing. */
+	memcpy(&dec_interrupt, &kn01_interrupt,
+		sizeof(kn01_interrupt));
+
+	/* CPU IRQ priorities. */
+	memcpy(&cpu_mask_nr_tbl, &kn01_cpu_mask_nr_tbl,
+		sizeof(kn01_cpu_mask_nr_tbl));
+
+	mips_cpu_irq_init();
+
+}				/* dec_init_kn01 */
+
+
+/*
+ * Machine-specific initialisation for KN230, aka DS5100, aka MIPSmate.
+ */
+static int kn230_interrupt[DEC_NR_INTS] __initdata = {
+	[DEC_IRQ_CASCADE]	= -1,
+	[DEC_IRQ_AB_RECV]	= -1,
+	[DEC_IRQ_AB_XMIT]	= -1,
+	[DEC_IRQ_DZ11]		= DEC_CPU_IRQ_NR(KN230_CPU_INR_DZ11),
+	[DEC_IRQ_ASC]		= -1,
+	[DEC_IRQ_FLOPPY]	= -1,
+	[DEC_IRQ_FPU]		= DEC_CPU_IRQ_NR(DEC_CPU_INR_FPU),
+	[DEC_IRQ_HALT]		= DEC_CPU_IRQ_NR(KN230_CPU_INR_HALT),
+	[DEC_IRQ_ISDN]		= -1,
+	[DEC_IRQ_LANCE]		= DEC_CPU_IRQ_NR(KN230_CPU_INR_LANCE),
+	[DEC_IRQ_BUS]		= DEC_CPU_IRQ_NR(KN230_CPU_INR_BUS),
+	[DEC_IRQ_PSU]		= -1,
+	[DEC_IRQ_RTC]		= DEC_CPU_IRQ_NR(KN230_CPU_INR_RTC),
+	[DEC_IRQ_SCC0]		= -1,
+	[DEC_IRQ_SCC1]		= -1,
+	[DEC_IRQ_SII]		= DEC_CPU_IRQ_NR(KN230_CPU_INR_SII),
+	[DEC_IRQ_TC0]		= -1,
+	[DEC_IRQ_TC1]		= -1,
+	[DEC_IRQ_TC2]		= -1,
+	[DEC_IRQ_TIMER]		= -1,
+	[DEC_IRQ_VIDEO]		= -1,
+	[DEC_IRQ_ASC_MERR]	= -1,
+	[DEC_IRQ_ASC_ERR]	= -1,
+	[DEC_IRQ_ASC_DMA]	= -1,
+	[DEC_IRQ_FLOPPY_ERR]	= -1,
+	[DEC_IRQ_ISDN_ERR]	= -1,
+	[DEC_IRQ_ISDN_RXDMA]	= -1,
+	[DEC_IRQ_ISDN_TXDMA]	= -1,
+	[DEC_IRQ_LANCE_MERR]	= -1,
+	[DEC_IRQ_SCC0A_RXERR]	= -1,
+	[DEC_IRQ_SCC0A_RXDMA]	= -1,
+	[DEC_IRQ_SCC0A_TXERR]	= -1,
+	[DEC_IRQ_SCC0A_TXDMA]	= -1,
+	[DEC_IRQ_AB_RXERR]	= -1,
+	[DEC_IRQ_AB_RXDMA]	= -1,
+	[DEC_IRQ_AB_TXERR]	= -1,
+	[DEC_IRQ_AB_TXDMA]	= -1,
+	[DEC_IRQ_SCC1A_RXERR]	= -1,
+	[DEC_IRQ_SCC1A_RXDMA]	= -1,
+	[DEC_IRQ_SCC1A_TXERR]	= -1,
+	[DEC_IRQ_SCC1A_TXDMA]	= -1,
+};
+
+static int_ptr kn230_cpu_mask_nr_tbl[][2] __initdata = {
+	{ { .i = DEC_CPU_IRQ_MASK(KN230_CPU_INR_BUS) },
+		{ .i = DEC_CPU_IRQ_NR(KN230_CPU_INR_BUS) } },
+	{ { .i = DEC_CPU_IRQ_MASK(KN230_CPU_INR_RTC) },
+		{ .i = DEC_CPU_IRQ_NR(KN230_CPU_INR_RTC) } },
+	{ { .i = DEC_CPU_IRQ_MASK(KN230_CPU_INR_DZ11) },
+		{ .i = DEC_CPU_IRQ_NR(KN230_CPU_INR_DZ11) } },
+	{ { .i = DEC_CPU_IRQ_MASK(KN230_CPU_INR_SII) },
+		{ .i = DEC_CPU_IRQ_NR(KN230_CPU_INR_SII) } },
+	{ { .i = DEC_CPU_IRQ_ALL },
+		{ .p = cpu_all_int } },
+};
+
+static void __init dec_init_kn230(void)
+{
+	/* IRQ routing. */
+	memcpy(&dec_interrupt, &kn230_interrupt,
+		sizeof(kn230_interrupt));
+
+	/* CPU IRQ priorities. */
+	memcpy(&cpu_mask_nr_tbl, &kn230_cpu_mask_nr_tbl,
+		sizeof(kn230_cpu_mask_nr_tbl));
+
+	mips_cpu_irq_init();
+
+}				/* dec_init_kn230 */
+
+
+/*
+ * Machine-specific initialisation for KN02, aka DS5000/200, aka 3max.
+ */
+static int kn02_interrupt[DEC_NR_INTS] __initdata = {
+	[DEC_IRQ_CASCADE]	= DEC_CPU_IRQ_NR(KN02_CPU_INR_CASCADE),
+	[DEC_IRQ_AB_RECV]	= -1,
+	[DEC_IRQ_AB_XMIT]	= -1,
+	[DEC_IRQ_DZ11]		= KN02_IRQ_NR(KN02_CSR_INR_DZ11),
+	[DEC_IRQ_ASC]		= KN02_IRQ_NR(KN02_CSR_INR_ASC),
+	[DEC_IRQ_FLOPPY]	= -1,
+	[DEC_IRQ_FPU]		= DEC_CPU_IRQ_NR(DEC_CPU_INR_FPU),
+	[DEC_IRQ_HALT]		= -1,
+	[DEC_IRQ_ISDN]		= -1,
+	[DEC_IRQ_LANCE]		= KN02_IRQ_NR(KN02_CSR_INR_LANCE),
+	[DEC_IRQ_BUS]		= DEC_CPU_IRQ_NR(KN02_CPU_INR_BUS),
+	[DEC_IRQ_PSU]		= -1,
+	[DEC_IRQ_RTC]		= DEC_CPU_IRQ_NR(KN02_CPU_INR_RTC),
+	[DEC_IRQ_SCC0]		= -1,
+	[DEC_IRQ_SCC1]		= -1,
+	[DEC_IRQ_SII]		= -1,
+	[DEC_IRQ_TC0]		= KN02_IRQ_NR(KN02_CSR_INR_TC0),
+	[DEC_IRQ_TC1]		= KN02_IRQ_NR(KN02_CSR_INR_TC1),
+	[DEC_IRQ_TC2]		= KN02_IRQ_NR(KN02_CSR_INR_TC2),
+	[DEC_IRQ_TIMER]		= -1,
+	[DEC_IRQ_VIDEO]		= -1,
+	[DEC_IRQ_ASC_MERR]	= -1,
+	[DEC_IRQ_ASC_ERR]	= -1,
+	[DEC_IRQ_ASC_DMA]	= -1,
+	[DEC_IRQ_FLOPPY_ERR]	= -1,
+	[DEC_IRQ_ISDN_ERR]	= -1,
+	[DEC_IRQ_ISDN_RXDMA]	= -1,
+	[DEC_IRQ_ISDN_TXDMA]	= -1,
+	[DEC_IRQ_LANCE_MERR]	= -1,
+	[DEC_IRQ_SCC0A_RXERR]	= -1,
+	[DEC_IRQ_SCC0A_RXDMA]	= -1,
+	[DEC_IRQ_SCC0A_TXERR]	= -1,
+	[DEC_IRQ_SCC0A_TXDMA]	= -1,
+	[DEC_IRQ_AB_RXERR]	= -1,
+	[DEC_IRQ_AB_RXDMA]	= -1,
+	[DEC_IRQ_AB_TXERR]	= -1,
+	[DEC_IRQ_AB_TXDMA]	= -1,
+	[DEC_IRQ_SCC1A_RXERR]	= -1,
+	[DEC_IRQ_SCC1A_RXDMA]	= -1,
+	[DEC_IRQ_SCC1A_TXERR]	= -1,
+	[DEC_IRQ_SCC1A_TXDMA]	= -1,
+};
+
+static int_ptr kn02_cpu_mask_nr_tbl[][2] __initdata = {
+	{ { .i = DEC_CPU_IRQ_MASK(KN02_CPU_INR_BUS) },
+		{ .i = DEC_CPU_IRQ_NR(KN02_CPU_INR_BUS) } },
+	{ { .i = DEC_CPU_IRQ_MASK(KN02_CPU_INR_RTC) },
+		{ .i = DEC_CPU_IRQ_NR(KN02_CPU_INR_RTC) } },
+	{ { .i = DEC_CPU_IRQ_MASK(KN02_CPU_INR_CASCADE) },
+		{ .p = kn02_io_int } },
+	{ { .i = DEC_CPU_IRQ_ALL },
+		{ .p = cpu_all_int } },
+};
+
+static int_ptr kn02_asic_mask_nr_tbl[][2] __initdata = {
+	{ { .i = KN02_IRQ_MASK(KN02_CSR_INR_DZ11) },
+		{ .i = KN02_IRQ_NR(KN02_CSR_INR_DZ11) } },
+	{ { .i = KN02_IRQ_MASK(KN02_CSR_INR_ASC) },
+		{ .i = KN02_IRQ_NR(KN02_CSR_INR_ASC) } },
+	{ { .i = KN02_IRQ_MASK(KN02_CSR_INR_LANCE) },
+		{ .i = KN02_IRQ_NR(KN02_CSR_INR_LANCE) } },
+	{ { .i = KN02_IRQ_MASK(KN02_CSR_INR_TC2) },
+		{ .i = KN02_IRQ_NR(KN02_CSR_INR_TC2) } },
+	{ { .i = KN02_IRQ_MASK(KN02_CSR_INR_TC1) },
+		{ .i = KN02_IRQ_NR(KN02_CSR_INR_TC1) } },
+	{ { .i = KN02_IRQ_MASK(KN02_CSR_INR_TC0) },
+		{ .i = KN02_IRQ_NR(KN02_CSR_INR_TC0) } },
+	{ { .i = KN02_IRQ_ALL },
+		{ .p = kn02_all_int } },
+};
+
+static void __init dec_init_kn02(void)
+{
+	/* IRQ routing. */
+	memcpy(&dec_interrupt, &kn02_interrupt,
+		sizeof(kn02_interrupt));
+
+	/* CPU IRQ priorities. */
+	memcpy(&cpu_mask_nr_tbl, &kn02_cpu_mask_nr_tbl,
+		sizeof(kn02_cpu_mask_nr_tbl));
+
+	/* KN02 CSR IRQ priorities. */
+	memcpy(&asic_mask_nr_tbl, &kn02_asic_mask_nr_tbl,
+		sizeof(kn02_asic_mask_nr_tbl));
+
+	mips_cpu_irq_init();
+	init_kn02_irqs(KN02_IRQ_BASE);
+
+}				/* dec_init_kn02 */
+
+
+/*
+ * Machine-specific initialisation for KN02-BA, aka DS5000/1xx
+ * (xx = 20, 25, 33), aka 3min.  Also applies to KN04(-BA), aka
+ * DS5000/150, aka 4min.
+ */
+static int kn02ba_interrupt[DEC_NR_INTS] __initdata = {
+	[DEC_IRQ_CASCADE]	= DEC_CPU_IRQ_NR(KN02BA_CPU_INR_CASCADE),
+	[DEC_IRQ_AB_RECV]	= -1,
+	[DEC_IRQ_AB_XMIT]	= -1,
+	[DEC_IRQ_DZ11]		= -1,
+	[DEC_IRQ_ASC]		= IO_IRQ_NR(KN02BA_IO_INR_ASC),
+	[DEC_IRQ_FLOPPY]	= -1,
+	[DEC_IRQ_FPU]		= DEC_CPU_IRQ_NR(DEC_CPU_INR_FPU),
+	[DEC_IRQ_HALT]		= DEC_CPU_IRQ_NR(KN02BA_CPU_INR_HALT),
+	[DEC_IRQ_ISDN]		= -1,
+	[DEC_IRQ_LANCE]		= IO_IRQ_NR(KN02BA_IO_INR_LANCE),
+	[DEC_IRQ_BUS]		= IO_IRQ_NR(KN02BA_IO_INR_BUS),
+	[DEC_IRQ_PSU]		= IO_IRQ_NR(KN02BA_IO_INR_PSU),
+	[DEC_IRQ_RTC]		= IO_IRQ_NR(KN02BA_IO_INR_RTC),
+	[DEC_IRQ_SCC0]		= IO_IRQ_NR(KN02BA_IO_INR_SCC0),
+	[DEC_IRQ_SCC1]		= IO_IRQ_NR(KN02BA_IO_INR_SCC1),
+	[DEC_IRQ_SII]		= -1,
+	[DEC_IRQ_TC0]		= DEC_CPU_IRQ_NR(KN02BA_CPU_INR_TC0),
+	[DEC_IRQ_TC1]		= DEC_CPU_IRQ_NR(KN02BA_CPU_INR_TC1),
+	[DEC_IRQ_TC2]		= DEC_CPU_IRQ_NR(KN02BA_CPU_INR_TC2),
+	[DEC_IRQ_TIMER]		= -1,
+	[DEC_IRQ_VIDEO]		= -1,
+	[DEC_IRQ_ASC_MERR]	= IO_IRQ_NR(IO_INR_ASC_MERR),
+	[DEC_IRQ_ASC_ERR]	= IO_IRQ_NR(IO_INR_ASC_ERR),
+	[DEC_IRQ_ASC_DMA]	= IO_IRQ_NR(IO_INR_ASC_DMA),
+	[DEC_IRQ_FLOPPY_ERR]	= -1,
+	[DEC_IRQ_ISDN_ERR]	= -1,
+	[DEC_IRQ_ISDN_RXDMA]	= -1,
+	[DEC_IRQ_ISDN_TXDMA]	= -1,
+	[DEC_IRQ_LANCE_MERR]	= IO_IRQ_NR(IO_INR_LANCE_MERR),
+	[DEC_IRQ_SCC0A_RXERR]	= IO_IRQ_NR(IO_INR_SCC0A_RXERR),
+	[DEC_IRQ_SCC0A_RXDMA]	= IO_IRQ_NR(IO_INR_SCC0A_RXDMA),
+	[DEC_IRQ_SCC0A_TXERR]	= IO_IRQ_NR(IO_INR_SCC0A_TXERR),
+	[DEC_IRQ_SCC0A_TXDMA]	= IO_IRQ_NR(IO_INR_SCC0A_TXDMA),
+	[DEC_IRQ_AB_RXERR]	= -1,
+	[DEC_IRQ_AB_RXDMA]	= -1,
+	[DEC_IRQ_AB_TXERR]	= -1,
+	[DEC_IRQ_AB_TXDMA]	= -1,
+	[DEC_IRQ_SCC1A_RXERR]	= IO_IRQ_NR(IO_INR_SCC1A_RXERR),
+	[DEC_IRQ_SCC1A_RXDMA]	= IO_IRQ_NR(IO_INR_SCC1A_RXDMA),
+	[DEC_IRQ_SCC1A_TXERR]	= IO_IRQ_NR(IO_INR_SCC1A_TXERR),
+	[DEC_IRQ_SCC1A_TXDMA]	= IO_IRQ_NR(IO_INR_SCC1A_TXDMA),
+};
+
+static int_ptr kn02ba_cpu_mask_nr_tbl[][2] __initdata = {
+	{ { .i = DEC_CPU_IRQ_MASK(KN02BA_CPU_INR_CASCADE) },
+		{ .p = kn02xa_io_int } },
+	{ { .i = DEC_CPU_IRQ_MASK(KN02BA_CPU_INR_TC2) },
+		{ .i = DEC_CPU_IRQ_NR(KN02BA_CPU_INR_TC2) } },
+	{ { .i = DEC_CPU_IRQ_MASK(KN02BA_CPU_INR_TC1) },
+		{ .i = DEC_CPU_IRQ_NR(KN02BA_CPU_INR_TC1) } },
+	{ { .i = DEC_CPU_IRQ_MASK(KN02BA_CPU_INR_TC0) },
+		{ .i = DEC_CPU_IRQ_NR(KN02BA_CPU_INR_TC0) } },
+	{ { .i = DEC_CPU_IRQ_ALL },
+		{ .p = cpu_all_int } },
+};
+
+static int_ptr kn02ba_asic_mask_nr_tbl[][2] __initdata = {
+	{ { .i = IO_IRQ_MASK(KN02BA_IO_INR_BUS) },
+		{ .i = IO_IRQ_NR(KN02BA_IO_INR_BUS) } },
+	{ { .i = IO_IRQ_MASK(KN02BA_IO_INR_RTC) },
+		{ .i = IO_IRQ_NR(KN02BA_IO_INR_RTC) } },
+	{ { .i = IO_IRQ_DMA },
+		{ .p = asic_dma_int } },
+	{ { .i = IO_IRQ_MASK(KN02BA_IO_INR_SCC0) },
+		{ .i = IO_IRQ_NR(KN02BA_IO_INR_SCC0) } },
+	{ { .i = IO_IRQ_MASK(KN02BA_IO_INR_SCC1) },
+		{ .i = IO_IRQ_NR(KN02BA_IO_INR_SCC1) } },
+	{ { .i = IO_IRQ_MASK(KN02BA_IO_INR_ASC) },
+		{ .i = IO_IRQ_NR(KN02BA_IO_INR_ASC) } },
+	{ { .i = IO_IRQ_MASK(KN02BA_IO_INR_LANCE) },
+		{ .i = IO_IRQ_NR(KN02BA_IO_INR_LANCE) } },
+	{ { .i = IO_IRQ_ALL },
+		{ .p = asic_all_int } },
+};
+
+static void __init dec_init_kn02ba(void)
+{
+	/* IRQ routing. */
+	memcpy(&dec_interrupt, &kn02ba_interrupt,
+		sizeof(kn02ba_interrupt));
+
+	/* CPU IRQ priorities. */
+	memcpy(&cpu_mask_nr_tbl, &kn02ba_cpu_mask_nr_tbl,
+		sizeof(kn02ba_cpu_mask_nr_tbl));
+
+	/* I/O ASIC IRQ priorities. */
+	memcpy(&asic_mask_nr_tbl, &kn02ba_asic_mask_nr_tbl,
+		sizeof(kn02ba_asic_mask_nr_tbl));
+
+	mips_cpu_irq_init();
+	init_ioasic_irqs(IO_IRQ_BASE);
+
+}				/* dec_init_kn02ba */
+
+
+/*
+ * Machine-specific initialisation for KN02-CA, aka DS5000/xx,
+ * (xx = 20, 25, 33), aka MAXine.  Also applies to KN04(-CA), aka
+ * DS5000/50, aka 4MAXine.
+ */
+static int kn02ca_interrupt[DEC_NR_INTS] __initdata = {
+	[DEC_IRQ_CASCADE]	= DEC_CPU_IRQ_NR(KN02CA_CPU_INR_CASCADE),
+	[DEC_IRQ_AB_RECV]	= IO_IRQ_NR(KN02CA_IO_INR_AB_RECV),
+	[DEC_IRQ_AB_XMIT]	= IO_IRQ_NR(KN02CA_IO_INR_AB_XMIT),
+	[DEC_IRQ_DZ11]		= -1,
+	[DEC_IRQ_ASC]		= IO_IRQ_NR(KN02CA_IO_INR_ASC),
+	[DEC_IRQ_FLOPPY]	= IO_IRQ_NR(KN02CA_IO_INR_FLOPPY),
+	[DEC_IRQ_FPU]		= DEC_CPU_IRQ_NR(DEC_CPU_INR_FPU),
+	[DEC_IRQ_HALT]		= DEC_CPU_IRQ_NR(KN02CA_CPU_INR_HALT),
+	[DEC_IRQ_ISDN]		= IO_IRQ_NR(KN02CA_IO_INR_ISDN),
+	[DEC_IRQ_LANCE]		= IO_IRQ_NR(KN02CA_IO_INR_LANCE),
+	[DEC_IRQ_BUS]		= DEC_CPU_IRQ_NR(KN02CA_CPU_INR_BUS),
+	[DEC_IRQ_PSU]		= -1,
+	[DEC_IRQ_RTC]		= DEC_CPU_IRQ_NR(KN02CA_CPU_INR_RTC),
+	[DEC_IRQ_SCC0]		= IO_IRQ_NR(KN02CA_IO_INR_SCC0),
+	[DEC_IRQ_SCC1]		= -1,
+	[DEC_IRQ_SII]		= -1,
+	[DEC_IRQ_TC0]		= IO_IRQ_NR(KN02CA_IO_INR_TC0),
+	[DEC_IRQ_TC1]		= IO_IRQ_NR(KN02CA_IO_INR_TC1),
+	[DEC_IRQ_TC2]		= -1,
+	[DEC_IRQ_TIMER]		= DEC_CPU_IRQ_NR(KN02CA_CPU_INR_TIMER),
+	[DEC_IRQ_VIDEO]		= IO_IRQ_NR(KN02CA_IO_INR_VIDEO),
+	[DEC_IRQ_ASC_MERR]	= IO_IRQ_NR(IO_INR_ASC_MERR),
+	[DEC_IRQ_ASC_ERR]	= IO_IRQ_NR(IO_INR_ASC_ERR),
+	[DEC_IRQ_ASC_DMA]	= IO_IRQ_NR(IO_INR_ASC_DMA),
+	[DEC_IRQ_FLOPPY_ERR]	= IO_IRQ_NR(IO_INR_FLOPPY_ERR),
+	[DEC_IRQ_ISDN_ERR]	= IO_IRQ_NR(IO_INR_ISDN_ERR),
+	[DEC_IRQ_ISDN_RXDMA]	= IO_IRQ_NR(IO_INR_ISDN_RXDMA),
+	[DEC_IRQ_ISDN_TXDMA]	= IO_IRQ_NR(IO_INR_ISDN_TXDMA),
+	[DEC_IRQ_LANCE_MERR]	= IO_IRQ_NR(IO_INR_LANCE_MERR),
+	[DEC_IRQ_SCC0A_RXERR]	= IO_IRQ_NR(IO_INR_SCC0A_RXERR),
+	[DEC_IRQ_SCC0A_RXDMA]	= IO_IRQ_NR(IO_INR_SCC0A_RXDMA),
+	[DEC_IRQ_SCC0A_TXERR]	= IO_IRQ_NR(IO_INR_SCC0A_TXERR),
+	[DEC_IRQ_SCC0A_TXDMA]	= IO_IRQ_NR(IO_INR_SCC0A_TXDMA),
+	[DEC_IRQ_AB_RXERR]	= IO_IRQ_NR(IO_INR_AB_RXERR),
+	[DEC_IRQ_AB_RXDMA]	= IO_IRQ_NR(IO_INR_AB_RXDMA),
+	[DEC_IRQ_AB_TXERR]	= IO_IRQ_NR(IO_INR_AB_TXERR),
+	[DEC_IRQ_AB_TXDMA]	= IO_IRQ_NR(IO_INR_AB_TXDMA),
+	[DEC_IRQ_SCC1A_RXERR]	= -1,
+	[DEC_IRQ_SCC1A_RXDMA]	= -1,
+	[DEC_IRQ_SCC1A_TXERR]	= -1,
+	[DEC_IRQ_SCC1A_TXDMA]	= -1,
+};
+
+static int_ptr kn02ca_cpu_mask_nr_tbl[][2] __initdata = {
+	{ { .i = DEC_CPU_IRQ_MASK(KN02CA_CPU_INR_BUS) },
+		{ .i = DEC_CPU_IRQ_NR(KN02CA_CPU_INR_BUS) } },
+	{ { .i = DEC_CPU_IRQ_MASK(KN02CA_CPU_INR_RTC) },
+		{ .i = DEC_CPU_IRQ_NR(KN02CA_CPU_INR_RTC) } },
+	{ { .i = DEC_CPU_IRQ_MASK(KN02CA_CPU_INR_CASCADE) },
+		{ .p = kn02xa_io_int } },
+	{ { .i = DEC_CPU_IRQ_ALL },
+		{ .p = cpu_all_int } },
+};
+
+static int_ptr kn02ca_asic_mask_nr_tbl[][2] __initdata = {
+	{ { .i = IO_IRQ_DMA },
+		{ .p = asic_dma_int } },
+	{ { .i = IO_IRQ_MASK(KN02CA_IO_INR_SCC0) },
+		{ .i = IO_IRQ_NR(KN02CA_IO_INR_SCC0) } },
+	{ { .i = IO_IRQ_MASK(KN02CA_IO_INR_ASC) },
+		{ .i = IO_IRQ_NR(KN02CA_IO_INR_ASC) } },
+	{ { .i = IO_IRQ_MASK(KN02CA_IO_INR_LANCE) },
+		{ .i = IO_IRQ_NR(KN02CA_IO_INR_LANCE) } },
+	{ { .i = IO_IRQ_MASK(KN02CA_IO_INR_TC1) },
+		{ .i = IO_IRQ_NR(KN02CA_IO_INR_TC1) } },
+	{ { .i = IO_IRQ_MASK(KN02CA_IO_INR_TC0) },
+		{ .i = IO_IRQ_NR(KN02CA_IO_INR_TC0) } },
+	{ { .i = IO_IRQ_ALL },
+		{ .p = asic_all_int } },
+};
+
+static void __init dec_init_kn02ca(void)
+{
+	/* IRQ routing. */
+	memcpy(&dec_interrupt, &kn02ca_interrupt,
+		sizeof(kn02ca_interrupt));
+
+	/* CPU IRQ priorities. */
+	memcpy(&cpu_mask_nr_tbl, &kn02ca_cpu_mask_nr_tbl,
+		sizeof(kn02ca_cpu_mask_nr_tbl));
+
+	/* I/O ASIC IRQ priorities. */
+	memcpy(&asic_mask_nr_tbl, &kn02ca_asic_mask_nr_tbl,
+		sizeof(kn02ca_asic_mask_nr_tbl));
+
+	mips_cpu_irq_init();
+	init_ioasic_irqs(IO_IRQ_BASE);
+
+}				/* dec_init_kn02ca */
+
+
+/*
+ * Machine-specific initialisation for KN03, aka DS5000/240,
+ * aka 3max+ and DS5900, aka BIGmax.  Also applies to KN05, aka
+ * DS5000/260, aka 4max+ and DS5900/260.
+ */
+static int kn03_interrupt[DEC_NR_INTS] __initdata = {
+	[DEC_IRQ_CASCADE]	= DEC_CPU_IRQ_NR(KN03_CPU_INR_CASCADE),
+	[DEC_IRQ_AB_RECV]	= -1,
+	[DEC_IRQ_AB_XMIT]	= -1,
+	[DEC_IRQ_DZ11]		= -1,
+	[DEC_IRQ_ASC]		= IO_IRQ_NR(KN03_IO_INR_ASC),
+	[DEC_IRQ_FLOPPY]	= -1,
+	[DEC_IRQ_FPU]		= DEC_CPU_IRQ_NR(DEC_CPU_INR_FPU),
+	[DEC_IRQ_HALT]		= DEC_CPU_IRQ_NR(KN03_CPU_INR_HALT),
+	[DEC_IRQ_ISDN]		= -1,
+	[DEC_IRQ_LANCE]		= IO_IRQ_NR(KN03_IO_INR_LANCE),
+	[DEC_IRQ_BUS]		= DEC_CPU_IRQ_NR(KN03_CPU_INR_BUS),
+	[DEC_IRQ_PSU]		= IO_IRQ_NR(KN03_IO_INR_PSU),
+	[DEC_IRQ_RTC]		= DEC_CPU_IRQ_NR(KN03_CPU_INR_RTC),
+	[DEC_IRQ_SCC0]		= IO_IRQ_NR(KN03_IO_INR_SCC0),
+	[DEC_IRQ_SCC1]		= IO_IRQ_NR(KN03_IO_INR_SCC1),
+	[DEC_IRQ_SII]		= -1,
+	[DEC_IRQ_TC0]		= IO_IRQ_NR(KN03_IO_INR_TC0),
+	[DEC_IRQ_TC1]		= IO_IRQ_NR(KN03_IO_INR_TC1),
+	[DEC_IRQ_TC2]		= IO_IRQ_NR(KN03_IO_INR_TC2),
+	[DEC_IRQ_TIMER]		= -1,
+	[DEC_IRQ_VIDEO]		= -1,
+	[DEC_IRQ_ASC_MERR]	= IO_IRQ_NR(IO_INR_ASC_MERR),
+	[DEC_IRQ_ASC_ERR]	= IO_IRQ_NR(IO_INR_ASC_ERR),
+	[DEC_IRQ_ASC_DMA]	= IO_IRQ_NR(IO_INR_ASC_DMA),
+	[DEC_IRQ_FLOPPY_ERR]	= -1,
+	[DEC_IRQ_ISDN_ERR]	= -1,
+	[DEC_IRQ_ISDN_RXDMA]	= -1,
+	[DEC_IRQ_ISDN_TXDMA]	= -1,
+	[DEC_IRQ_LANCE_MERR]	= IO_IRQ_NR(IO_INR_LANCE_MERR),
+	[DEC_IRQ_SCC0A_RXERR]	= IO_IRQ_NR(IO_INR_SCC0A_RXERR),
+	[DEC_IRQ_SCC0A_RXDMA]	= IO_IRQ_NR(IO_INR_SCC0A_RXDMA),
+	[DEC_IRQ_SCC0A_TXERR]	= IO_IRQ_NR(IO_INR_SCC0A_TXERR),
+	[DEC_IRQ_SCC0A_TXDMA]	= IO_IRQ_NR(IO_INR_SCC0A_TXDMA),
+	[DEC_IRQ_AB_RXERR]	= -1,
+	[DEC_IRQ_AB_RXDMA]	= -1,
+	[DEC_IRQ_AB_TXERR]	= -1,
+	[DEC_IRQ_AB_TXDMA]	= -1,
+	[DEC_IRQ_SCC1A_RXERR]	= IO_IRQ_NR(IO_INR_SCC1A_RXERR),
+	[DEC_IRQ_SCC1A_RXDMA]	= IO_IRQ_NR(IO_INR_SCC1A_RXDMA),
+	[DEC_IRQ_SCC1A_TXERR]	= IO_IRQ_NR(IO_INR_SCC1A_TXERR),
+	[DEC_IRQ_SCC1A_TXDMA]	= IO_IRQ_NR(IO_INR_SCC1A_TXDMA),
+};
+
+static int_ptr kn03_cpu_mask_nr_tbl[][2] __initdata = {
+	{ { .i = DEC_CPU_IRQ_MASK(KN03_CPU_INR_BUS) },
+		{ .i = DEC_CPU_IRQ_NR(KN03_CPU_INR_BUS) } },
+	{ { .i = DEC_CPU_IRQ_MASK(KN03_CPU_INR_RTC) },
+		{ .i = DEC_CPU_IRQ_NR(KN03_CPU_INR_RTC) } },
+	{ { .i = DEC_CPU_IRQ_MASK(KN03_CPU_INR_CASCADE) },
+		{ .p = kn03_io_int } },
+	{ { .i = DEC_CPU_IRQ_ALL },
+		{ .p = cpu_all_int } },
+};
+
+static int_ptr kn03_asic_mask_nr_tbl[][2] __initdata = {
+	{ { .i = IO_IRQ_DMA },
+		{ .p = asic_dma_int } },
+	{ { .i = IO_IRQ_MASK(KN03_IO_INR_SCC0) },
+		{ .i = IO_IRQ_NR(KN03_IO_INR_SCC0) } },
+	{ { .i = IO_IRQ_MASK(KN03_IO_INR_SCC1) },
+		{ .i = IO_IRQ_NR(KN03_IO_INR_SCC1) } },
+	{ { .i = IO_IRQ_MASK(KN03_IO_INR_ASC) },
+		{ .i = IO_IRQ_NR(KN03_IO_INR_ASC) } },
+	{ { .i = IO_IRQ_MASK(KN03_IO_INR_LANCE) },
+		{ .i = IO_IRQ_NR(KN03_IO_INR_LANCE) } },
+	{ { .i = IO_IRQ_MASK(KN03_IO_INR_TC2) },
+		{ .i = IO_IRQ_NR(KN03_IO_INR_TC2) } },
+	{ { .i = IO_IRQ_MASK(KN03_IO_INR_TC1) },
+		{ .i = IO_IRQ_NR(KN03_IO_INR_TC1) } },
+	{ { .i = IO_IRQ_MASK(KN03_IO_INR_TC0) },
+		{ .i = IO_IRQ_NR(KN03_IO_INR_TC0) } },
+	{ { .i = IO_IRQ_ALL },
+		{ .p = asic_all_int } },
+};
+
+static void __init dec_init_kn03(void)
+{
+	/* IRQ routing. */
+	memcpy(&dec_interrupt, &kn03_interrupt,
+		sizeof(kn03_interrupt));
+
+	/* CPU IRQ priorities. */
+	memcpy(&cpu_mask_nr_tbl, &kn03_cpu_mask_nr_tbl,
+		sizeof(kn03_cpu_mask_nr_tbl));
+
+	/* I/O ASIC IRQ priorities. */
+	memcpy(&asic_mask_nr_tbl, &kn03_asic_mask_nr_tbl,
+		sizeof(kn03_asic_mask_nr_tbl));
+
+	mips_cpu_irq_init();
+	init_ioasic_irqs(IO_IRQ_BASE);
+
+}				/* dec_init_kn03 */
+
+
+void __init arch_init_irq(void)
+{
+	switch (mips_machtype) {
+	case MACH_DS23100:	/* DS2100/DS3100 Pmin/Pmax */
+		dec_init_kn01();
+		break;
+	case MACH_DS5100:	/* DS5100 MIPSmate */
+		dec_init_kn230();
+		break;
+	case MACH_DS5000_200:	/* DS5000/200 3max */
+		dec_init_kn02();
+		break;
+	case MACH_DS5000_1XX:	/* DS5000/1xx 3min */
+		dec_init_kn02ba();
+		break;
+	case MACH_DS5000_2X0:	/* DS5000/240 3max+ */
+	case MACH_DS5900:	/* DS5900 bigmax */
+		dec_init_kn03();
+		break;
+	case MACH_DS5000_XX:	/* Personal DS5000/xx */
+		dec_init_kn02ca();
+		break;
+	case MACH_DS5800:	/* DS5800 Isis */
+		panic("Don't know how to set this up!");
+		break;
+	case MACH_DS5400:	/* DS5400 MIPSfair */
+		panic("Don't know how to set this up!");
+		break;
+	case MACH_DS5500:	/* DS5500 MIPSfair-2 */
+		panic("Don't know how to set this up!");
+		break;
+	}
+
+	/* Free the FPU interrupt if the exception is present. */
+	if (!cpu_has_nofpuex) {
+		cpu_fpu_mask = 0;
+		dec_interrupt[DEC_IRQ_FPU] = -1;
+	}
+	/* Free the halt interrupt unused on R4k systems.  */
+	if (current_cpu_type() == CPU_R4000SC ||
+	    current_cpu_type() == CPU_R4400SC)
+		dec_interrupt[DEC_IRQ_HALT] = -1;
+
+	/* Register board interrupts: FPU and cascade. */
+	if (IS_ENABLED(CONFIG_MIPS_FP_SUPPORT) &&
+	    dec_interrupt[DEC_IRQ_FPU] >= 0 && cpu_has_fpu) {
+		struct irq_desc *desc_fpu;
+		int irq_fpu;
+
+		irq_fpu = dec_interrupt[DEC_IRQ_FPU];
+		if (request_irq(irq_fpu, no_action, IRQF_NO_THREAD, "fpu",
+				NULL))
+			pr_err("Failed to register fpu interrupt\n");
+		desc_fpu = irq_to_desc(irq_fpu);
+		fpu_kstat_irq = this_cpu_ptr(desc_fpu->kstat_irqs);
+	}
+	if (dec_interrupt[DEC_IRQ_CASCADE] >= 0) {
+		if (request_irq(dec_interrupt[DEC_IRQ_CASCADE], no_action,
+				IRQF_NO_THREAD, "cascade", NULL))
+			pr_err("Failed to register cascade interrupt\n");
+	}
+	/* Register the bus error interrupt. */
+	if (dec_interrupt[DEC_IRQ_BUS] >= 0 && busirq_handler) {
+		if (request_irq(dec_interrupt[DEC_IRQ_BUS], busirq_handler,
+				busirq_flags, "bus error", busirq_handler))
+			pr_err("Failed to register bus error interrupt\n");
+	}
+	/* Register the HALT interrupt. */
+	if (dec_interrupt[DEC_IRQ_HALT] >= 0) {
+		if (request_irq(dec_interrupt[DEC_IRQ_HALT], dec_intr_halt,
+				IRQF_NO_THREAD, "halt", NULL))
+			pr_err("Failed to register halt interrupt\n");
+	}
+}
+
+asmlinkage unsigned int dec_irq_dispatch(unsigned int irq)
+{
+	do_IRQ(irq);
+	return 0;
+}
diff --git a/arch/mips/dec/tc.c b/arch/mips/dec/tc.c
new file mode 100644
index 000000000..dba583976
--- /dev/null
+++ b/arch/mips/dec/tc.c
@@ -0,0 +1,95 @@
+/*
+ *	TURBOchannel architecture calls.
+ *
+ *	Copyright (c) Harald Koerfgen, 1998
+ *	Copyright (c) 2001, 2003, 2005, 2006  Maciej W. Rozycki
+ *	Copyright (c) 2005  James Simmons
+ *
+ *	This file is subject to the terms and conditions of the GNU
+ *	General Public License.  See the file "COPYING" in the main
+ *	directory of this archive for more details.
+ */
+#include <linux/compiler.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/string.h>
+#include <linux/tc.h>
+#include <linux/types.h>
+
+#include <asm/addrspace.h>
+#include <asm/bootinfo.h>
+#include <asm/paccess.h>
+
+#include <asm/dec/interrupts.h>
+#include <asm/dec/prom.h>
+#include <asm/dec/system.h>
+
+/*
+ * Protected read byte from TURBOchannel slot space.
+ */
+int tc_preadb(u8 *valp, void __iomem *addr)
+{
+	return get_dbe(*valp, (u8 *)addr);
+}
+
+/*
+ * Get TURBOchannel bus information as specified by the spec, plus
+ * the slot space base address and the number of slots.
+ */
+int __init tc_bus_get_info(struct tc_bus *tbus)
+{
+	if (!dec_tc_bus)
+		return -ENXIO;
+
+	memcpy(&tbus->info, rex_gettcinfo(), sizeof(tbus->info));
+	tbus->slot_base = CPHYSADDR((long)rex_slot_address(0));
+
+	switch (mips_machtype) {
+	case MACH_DS5000_200:
+		tbus->num_tcslots = 7;
+		break;
+	case MACH_DS5000_2X0:
+	case MACH_DS5900:
+		tbus->ext_slot_base = 0x20000000;
+		tbus->ext_slot_size = 0x20000000;
+		fallthrough;
+	case MACH_DS5000_1XX:
+		tbus->num_tcslots = 3;
+		break;
+	case MACH_DS5000_XX:
+		tbus->num_tcslots = 2;
+	default:
+		break;
+	}
+	return 0;
+}
+
+/*
+ * Get the IRQ for the specified slot.
+ */
+void __init tc_device_get_irq(struct tc_dev *tdev)
+{
+	switch (tdev->slot) {
+	case 0:
+		tdev->interrupt = dec_interrupt[DEC_IRQ_TC0];
+		break;
+	case 1:
+		tdev->interrupt = dec_interrupt[DEC_IRQ_TC1];
+		break;
+	case 2:
+		tdev->interrupt = dec_interrupt[DEC_IRQ_TC2];
+		break;
+	/*
+	 * Yuck! DS5000/200 onboard devices
+	 */
+	case 5:
+		tdev->interrupt = dec_interrupt[DEC_IRQ_TC5];
+		break;
+	case 6:
+		tdev->interrupt = dec_interrupt[DEC_IRQ_TC6];
+		break;
+	default:
+		tdev->interrupt = -1;
+		break;
+	}
+}
diff --git a/arch/mips/dec/time.c b/arch/mips/dec/time.c
new file mode 100644
index 000000000..c38686f89
--- /dev/null
+++ b/arch/mips/dec/time.c
@@ -0,0 +1,172 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ *  Copyright (C) 1991, 1992, 1995  Linus Torvalds
+ *  Copyright (C) 2000, 2003  Maciej W. Rozycki
+ *
+ * This file contains the time handling details for PC-style clocks as
+ * found in some MIPS systems.
+ *
+ */
+#include <linux/bcd.h>
+#include <linux/init.h>
+#include <linux/mc146818rtc.h>
+#include <linux/param.h>
+
+#include <asm/cpu-features.h>
+#include <asm/ds1287.h>
+#include <asm/time.h>
+#include <asm/dec/interrupts.h>
+#include <asm/dec/ioasic.h>
+#include <asm/dec/machtype.h>
+
+void read_persistent_clock64(struct timespec64 *ts)
+{
+	unsigned int year, mon, day, hour, min, sec, real_year;
+	unsigned long flags;
+
+	spin_lock_irqsave(&rtc_lock, flags);
+
+	do {
+		sec = CMOS_READ(RTC_SECONDS);
+		min = CMOS_READ(RTC_MINUTES);
+		hour = CMOS_READ(RTC_HOURS);
+		day = CMOS_READ(RTC_DAY_OF_MONTH);
+		mon = CMOS_READ(RTC_MONTH);
+		year = CMOS_READ(RTC_YEAR);
+		/*
+		 * The PROM will reset the year to either '72 or '73.
+		 * Therefore we store the real year separately, in one
+		 * of unused BBU RAM locations.
+		 */
+		real_year = CMOS_READ(RTC_DEC_YEAR);
+	} while (sec != CMOS_READ(RTC_SECONDS));
+
+	spin_unlock_irqrestore(&rtc_lock, flags);
+
+	if (!(CMOS_READ(RTC_CONTROL) & RTC_DM_BINARY) || RTC_ALWAYS_BCD) {
+		sec = bcd2bin(sec);
+		min = bcd2bin(min);
+		hour = bcd2bin(hour);
+		day = bcd2bin(day);
+		mon = bcd2bin(mon);
+		year = bcd2bin(year);
+	}
+
+	year += real_year - 72 + 2000;
+
+	ts->tv_sec = mktime64(year, mon, day, hour, min, sec);
+	ts->tv_nsec = 0;
+}
+
+/*
+ * In order to set the CMOS clock precisely, update_persistent_clock64 has to
+ * be called 500 ms after the second nowtime has started, because when
+ * nowtime is written into the registers of the CMOS clock, it will
+ * jump to the next second precisely 500 ms later.  Check the Dallas
+ * DS1287 data sheet for details.
+ */
+int update_persistent_clock64(struct timespec64 now)
+{
+	time64_t nowtime = now.tv_sec;
+	int retval = 0;
+	int real_seconds, real_minutes, cmos_minutes;
+	unsigned char save_control, save_freq_select;
+
+	/* irq are locally disabled here */
+	spin_lock(&rtc_lock);
+	/* tell the clock it's being set */
+	save_control = CMOS_READ(RTC_CONTROL);
+	CMOS_WRITE((save_control | RTC_SET), RTC_CONTROL);
+
+	/* stop and reset prescaler */
+	save_freq_select = CMOS_READ(RTC_FREQ_SELECT);
+	CMOS_WRITE((save_freq_select | RTC_DIV_RESET2), RTC_FREQ_SELECT);
+
+	cmos_minutes = CMOS_READ(RTC_MINUTES);
+	if (!(save_control & RTC_DM_BINARY) || RTC_ALWAYS_BCD)
+		cmos_minutes = bcd2bin(cmos_minutes);
+
+	/*
+	 * since we're only adjusting minutes and seconds,
+	 * don't interfere with hour overflow. This avoids
+	 * messing with unknown time zones but requires your
+	 * RTC not to be off by more than 15 minutes
+	 */
+	real_minutes = div_s64_rem(nowtime, 60, &real_seconds);
+	if (((abs(real_minutes - cmos_minutes) + 15) / 30) & 1)
+		real_minutes += 30;	/* correct for half hour time zone */
+	real_minutes %= 60;
+
+	if (abs(real_minutes - cmos_minutes) < 30) {
+		if (!(save_control & RTC_DM_BINARY) || RTC_ALWAYS_BCD) {
+			real_seconds = bin2bcd(real_seconds);
+			real_minutes = bin2bcd(real_minutes);
+		}
+		CMOS_WRITE(real_seconds, RTC_SECONDS);
+		CMOS_WRITE(real_minutes, RTC_MINUTES);
+	} else {
+		printk_once(KERN_NOTICE
+		       "set_rtc_mmss: can't update from %d to %d\n",
+		       cmos_minutes, real_minutes);
+		retval = -1;
+	}
+
+	/* The following flags have to be released exactly in this order,
+	 * otherwise the DS1287 will not reset the oscillator and will not
+	 * update precisely 500 ms later.  You won't find this mentioned
+	 * in the Dallas Semiconductor data sheets, but who believes data
+	 * sheets anyway ...                           -- Markus Kuhn
+	 */
+	CMOS_WRITE(save_control, RTC_CONTROL);
+	CMOS_WRITE(save_freq_select, RTC_FREQ_SELECT);
+	spin_unlock(&rtc_lock);
+
+	return retval;
+}
+
+void __init plat_time_init(void)
+{
+	int ioasic_clock = 0;
+	u32 start, end;
+	int i = HZ / 8;
+
+	/* Set up the rate of periodic DS1287 interrupts. */
+	ds1287_set_base_clock(HZ);
+
+	/* On some I/O ASIC systems we have the I/O ASIC's counter.  */
+	if (IOASIC)
+		ioasic_clock = dec_ioasic_clocksource_init() == 0;
+	if (cpu_has_counter) {
+		ds1287_timer_state();
+		while (!ds1287_timer_state())
+			;
+
+		start = read_c0_count();
+
+		while (i--)
+			while (!ds1287_timer_state())
+				;
+
+		end = read_c0_count();
+
+		mips_hpt_frequency = (end - start) * 8;
+		printk(KERN_INFO "MIPS counter frequency %dHz\n",
+			mips_hpt_frequency);
+
+		/*
+		 * All R4k DECstations suffer from the CP0 Count erratum,
+		 * so we can't use the timer as a clock source, and a clock
+		 * event both at a time.  An accurate wall clock is more
+		 * important than a high-precision interval timer so only
+		 * use the timer as a clock source, and not a clock event
+		 * if there's no I/O ASIC counter available to serve as a
+		 * clock source.
+		 */
+		if (!ioasic_clock) {
+			init_r4k_clocksource();
+			mips_hpt_frequency = 0;
+		}
+	}
+
+	ds1287_clockevent_init(dec_interrupt[DEC_IRQ_RTC]);
+}
diff --git a/arch/mips/dec/wbflush.c b/arch/mips/dec/wbflush.c
new file mode 100644
index 000000000..dad64d178
--- /dev/null
+++ b/arch/mips/dec/wbflush.c
@@ -0,0 +1,92 @@
+/*
+ * Setup the right wbflush routine for the different DECstations.
+ *
+ * Created with information from:
+ *	DECstation 3100 Desktop Workstation Functional Specification
+ *	DECstation 5000/200 KN02 System Module Functional Specification
+ *	mipsel-linux-objdump --disassemble vmunix | grep "wbflush" :-)
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1998 Harald Koerfgen
+ * Copyright (C) 2002 Maciej W. Rozycki
+ */
+
+#include <linux/export.h>
+#include <linux/init.h>
+
+#include <asm/bootinfo.h>
+#include <asm/wbflush.h>
+#include <asm/barrier.h>
+
+static void wbflush_kn01(void);
+static void wbflush_kn210(void);
+static void wbflush_mips(void);
+
+void (*__wbflush) (void);
+
+void __init wbflush_setup(void)
+{
+	switch (mips_machtype) {
+	case MACH_DS23100:
+	case MACH_DS5000_200:	/* DS5000 3max */
+		__wbflush = wbflush_kn01;
+		break;
+	case MACH_DS5100:	/* DS5100 MIPSMATE */
+		__wbflush = wbflush_kn210;
+		break;
+	case MACH_DS5000_1XX:	/* DS5000/100 3min */
+	case MACH_DS5000_XX:	/* Personal DS5000/2x */
+	case MACH_DS5000_2X0:	/* DS5000/240 3max+ */
+	case MACH_DS5900:	/* DS5900 bigmax */
+	default:
+		__wbflush = wbflush_mips;
+		break;
+	}
+}
+
+/*
+ * For the DS3100 and DS5000/200 the R2020/R3220 writeback buffer functions
+ * as part of Coprocessor 0.
+ */
+static void wbflush_kn01(void)
+{
+    asm(".set\tpush\n\t"
+	".set\tnoreorder\n\t"
+	"1:\tbc0f\t1b\n\t"
+	"nop\n\t"
+	".set\tpop");
+}
+
+/*
+ * For the DS5100 the writeback buffer seems to be a part of Coprocessor 3.
+ * But CP3 has to enabled first.
+ */
+static void wbflush_kn210(void)
+{
+    asm(".set\tpush\n\t"
+	".set\tnoreorder\n\t"
+	"mfc0\t$2,$12\n\t"
+	"lui\t$3,0x8000\n\t"
+	"or\t$3,$2,$3\n\t"
+	"mtc0\t$3,$12\n\t"
+	"nop\n"
+	"1:\tbc3f\t1b\n\t"
+	"nop\n\t"
+	"mtc0\t$2,$12\n\t"
+	"nop\n\t"
+	".set\tpop"
+	: : : "$2", "$3");
+}
+
+/*
+ * I/O ASIC systems use a standard writeback buffer that gets flushed
+ * upon an uncached read.
+ */
+static void wbflush_mips(void)
+{
+	__fast_iob();
+}
+EXPORT_SYMBOL(__wbflush);
diff --git a/arch/mips/fw/arc/Makefile b/arch/mips/fw/arc/Makefile
new file mode 100644
index 000000000..64d685efc
--- /dev/null
+++ b/arch/mips/fw/arc/Makefile
@@ -0,0 +1,15 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Makefile for the ARC prom monitor library routines under Linux.
+#
+
+ifdef CONFIG_ARC_CMDLINE_ONLY
+lib-y				+= cmdline.o
+else
+lib-y				+= cmdline.o env.o file.o identify.o init.o \
+				   misc.o
+endif
+
+lib-$(CONFIG_ARC_MEMORY)	+= memory.o
+lib-$(CONFIG_ARC_CONSOLE)	+= arc_con.o
+lib-$(CONFIG_ARC_PROMLIB)	+= promlib.o
diff --git a/arch/mips/fw/arc/arc_con.c b/arch/mips/fw/arc/arc_con.c
new file mode 100644
index 000000000..7fdce236b
--- /dev/null
+++ b/arch/mips/fw/arc/arc_con.c
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Wrap-around code for a console using the
+ * ARC io-routines.
+ *
+ * Copyright (c) 1998 Harald Koerfgen
+ * Copyright (c) 2001 Ralf Baechle
+ * Copyright (c) 2002 Thiemo Seufer
+ */
+#include <linux/tty.h>
+#include <linux/major.h>
+#include <linux/init.h>
+#include <linux/console.h>
+#include <linux/fs.h>
+#include <asm/setup.h>
+#include <asm/sgialib.h>
+
+static void prom_console_write(struct console *co, const char *s,
+			       unsigned count)
+{
+	/* Do each character */
+	while (count--) {
+		if (*s == '\n')
+			prom_putchar('\r');
+		prom_putchar(*s++);
+	}
+}
+
+static int prom_console_setup(struct console *co, char *options)
+{
+	if (prom_flags & PROM_FLAG_USE_AS_CONSOLE)
+		return 0;
+	return -ENODEV;
+}
+
+static struct console arc_cons = {
+	.name		= "arc",
+	.write		= prom_console_write,
+	.setup		= prom_console_setup,
+	.flags		= CON_PRINTBUFFER,
+	.index		= -1,
+};
+
+/*
+ *    Register console.
+ */
+
+static int __init arc_console_init(void)
+{
+	register_console(&arc_cons);
+
+	return 0;
+}
+console_initcall(arc_console_init);
diff --git a/arch/mips/fw/arc/cmdline.c b/arch/mips/fw/arc/cmdline.c
new file mode 100644
index 000000000..155c5e911
--- /dev/null
+++ b/arch/mips/fw/arc/cmdline.c
@@ -0,0 +1,110 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * cmdline.c: Kernel command line creation using ARCS argc/argv.
+ *
+ * Copyright (C) 1996 David S. Miller (davem@davemloft.net)
+ */
+#include <linux/bug.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/string.h>
+
+#include <asm/sgialib.h>
+#include <asm/bootinfo.h>
+
+#undef DEBUG_CMDLINE
+
+/*
+ * A 32-bit ARC PROM pass arguments and environment as 32-bit pointer.
+ * These macro take care of sign extension.
+ */
+#define prom_argv(index) ((char *) (long)argv[(index)])
+
+static char *ignored[] = {
+	"ConsoleIn=",
+	"ConsoleOut=",
+	"SystemPartition=",
+	"OSLoader=",
+	"OSLoadPartition=",
+	"OSLoadFilename=",
+	"OSLoadOptions="
+};
+
+static char *used_arc[][2] = {
+	{ "OSLoadPartition=", "root=" },
+	{ "OSLoadOptions=", "" }
+};
+
+static char __init *move_firmware_args(int argc, LONG *argv, char *cp)
+{
+	char *s;
+	int actr, i;
+
+	actr = 1; /* Always ignore argv[0] */
+
+	while (actr < argc) {
+		for(i = 0; i < ARRAY_SIZE(used_arc); i++) {
+			int len = strlen(used_arc[i][0]);
+
+			if (!strncmp(prom_argv(actr), used_arc[i][0], len)) {
+			/* Ok, we want it. First append the replacement... */
+				strcat(cp, used_arc[i][1]);
+				cp += strlen(used_arc[i][1]);
+				/* ... and now the argument */
+				s = strchr(prom_argv(actr), '=');
+				if (s) {
+					s++;
+					strcpy(cp, s);
+					cp += strlen(s);
+				}
+				*cp++ = ' ';
+				break;
+			}
+		}
+		actr++;
+	}
+
+	return cp;
+}
+
+void __init prom_init_cmdline(int argc, LONG *argv)
+{
+	char *cp;
+	int actr, i;
+
+	actr = 1; /* Always ignore argv[0] */
+
+	cp = arcs_cmdline;
+	/*
+	 * Move ARC variables to the beginning to make sure they can be
+	 * overridden by later arguments.
+	 */
+	cp = move_firmware_args(argc, argv, cp);
+
+	while (actr < argc) {
+		for (i = 0; i < ARRAY_SIZE(ignored); i++) {
+			int len = strlen(ignored[i]);
+
+			if (!strncmp(prom_argv(actr), ignored[i], len))
+				goto pic_cont;
+		}
+		/* Ok, we want it. */
+		strcpy(cp, prom_argv(actr));
+		cp += strlen(prom_argv(actr));
+		*cp++ = ' ';
+
+	pic_cont:
+		actr++;
+	}
+
+	if (cp != arcs_cmdline)		/* get rid of trailing space */
+		--cp;
+	*cp = '\0';
+
+#ifdef DEBUG_CMDLINE
+	printk(KERN_DEBUG "prom cmdline: %s\n", arcs_cmdline);
+#endif
+}
diff --git a/arch/mips/fw/arc/env.c b/arch/mips/fw/arc/env.c
new file mode 100644
index 000000000..02407a7bb
--- /dev/null
+++ b/arch/mips/fw/arc/env.c
@@ -0,0 +1,21 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * env.c: ARCS environment variable routines.
+ *
+ * Copyright (C) 1996 David S. Miller (davem@davemloft.net)
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/string.h>
+
+#include <asm/fw/arc/types.h>
+#include <asm/sgialib.h>
+
+PCHAR __init
+ArcGetEnvironmentVariable(CHAR *name)
+{
+	return (CHAR *) ARC_CALL1(get_evar, name);
+}
diff --git a/arch/mips/fw/arc/file.c b/arch/mips/fw/arc/file.c
new file mode 100644
index 000000000..b0d8535c8
--- /dev/null
+++ b/arch/mips/fw/arc/file.c
@@ -0,0 +1,25 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * ARC firmware interface.
+ *
+ * Copyright (C) 1994, 1995, 1996, 1999 Ralf Baechle
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ */
+
+#include <asm/fw/arc/types.h>
+#include <asm/sgialib.h>
+
+LONG
+ArcRead(ULONG FileID, VOID *Buffer, ULONG N, ULONG *Count)
+{
+	return ARC_CALL4(read, FileID, Buffer, N, Count);
+}
+
+LONG
+ArcWrite(ULONG FileID, PVOID Buffer, ULONG N, PULONG Count)
+{
+	return ARC_CALL4(write, FileID, Buffer, N, Count);
+}
diff --git a/arch/mips/fw/arc/identify.c b/arch/mips/fw/arc/identify.c
new file mode 100644
index 000000000..5527e0f54
--- /dev/null
+++ b/arch/mips/fw/arc/identify.c
@@ -0,0 +1,111 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * identify.c: identify machine by looking up system identifier
+ *
+ * Copyright (C) 1998 Thomas Bogendoerfer
+ *
+ * This code is based on arch/mips/sgi/kernel/system.c, which is
+ *
+ * Copyright (C) 1996 David S. Miller (davem@davemloft.net)
+ */
+#include <linux/bug.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/string.h>
+
+#include <asm/sgialib.h>
+#include <asm/bootinfo.h>
+
+struct smatch {
+	char *arcname;
+	char *liname;
+	int flags;
+};
+
+static struct smatch mach_table[] = {
+	{
+		.arcname	= "SGI-IP22",
+		.liname		= "SGI Indy",
+		.flags		= PROM_FLAG_ARCS,
+	}, {
+		.arcname	= "SGI-IP28",
+		.liname		= "SGI IP28",
+		.flags		= PROM_FLAG_ARCS,
+	}, {
+		.arcname	= "SGI-IP30",
+		.liname		= "SGI Octane",
+		.flags		= PROM_FLAG_ARCS,
+	}, {
+		.arcname	= "SGI-IP32",
+		.liname		= "SGI O2",
+		.flags		= PROM_FLAG_ARCS,
+	}, {
+		.arcname	= "Microsoft-Jazz",
+		.liname		= "Jazz MIPS_Magnum_4000",
+		.flags		= 0,
+	}, {
+		.arcname	= "PICA-61",
+		.liname		= "Jazz Acer_PICA_61",
+		.flags		= 0,
+	}, {
+		.arcname	= "RM200PCI",
+		.liname		= "SNI RM200_PCI",
+		.flags		= PROM_FLAG_DONT_FREE_TEMP,
+	}, {
+		.arcname	= "RM200PCI-R5K",
+		.liname		= "SNI RM200_PCI-R5K",
+		.flags		= PROM_FLAG_DONT_FREE_TEMP,
+	}
+};
+
+int prom_flags;
+
+static struct smatch * __init string_to_mach(const char *s)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(mach_table); i++) {
+		if (!strcmp(s, mach_table[i].arcname))
+			return &mach_table[i];
+	}
+
+	panic("Yeee, could not determine architecture type <%s>", s);
+}
+
+char *system_type;
+
+const char *get_system_type(void)
+{
+	return system_type;
+}
+
+static pcomponent * __init ArcGetChild(pcomponent *Current)
+{
+	return (pcomponent *) ARC_CALL1(child_component, Current);
+}
+
+void __init prom_identify_arch(void)
+{
+	pcomponent *p;
+	struct smatch *mach;
+	const char *iname;
+
+	/*
+	 * The root component tells us what machine architecture we have here.
+	 */
+	p = ArcGetChild(PROM_NULL_COMPONENT);
+	if (p == NULL) {
+		iname = "Unknown";
+	} else
+		iname = (char *) (long) p->iname;
+
+	printk("ARCH: %s\n", iname);
+	mach = string_to_mach(iname);
+	system_type = mach->liname;
+
+	prom_flags = mach->flags;
+}
diff --git a/arch/mips/fw/arc/init.c b/arch/mips/fw/arc/init.c
new file mode 100644
index 000000000..f9d1dea9b
--- /dev/null
+++ b/arch/mips/fw/arc/init.c
@@ -0,0 +1,51 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * PROM library initialisation code.
+ *
+ * Copyright (C) 1996 David S. Miller (davem@davemloft.net)
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+
+#include <asm/bootinfo.h>
+#include <asm/sgialib.h>
+#include <asm/smp-ops.h>
+
+#undef DEBUG_PROM_INIT
+
+/* Master romvec interface. */
+struct linux_romvec *romvec;
+
+#if defined(CONFIG_64BIT) && defined(CONFIG_FW_ARC32)
+/* stack for calling 32bit ARC prom */
+u64 o32_stk[4096];
+#endif
+
+void __init prom_init(void)
+{
+	PSYSTEM_PARAMETER_BLOCK pb = PROMBLOCK;
+
+	romvec = ROMVECTOR;
+
+	if (pb->magic != 0x53435241) {
+		printk(KERN_CRIT "Aieee, bad prom vector magic %08lx\n",
+		       (unsigned long) pb->magic);
+		while(1)
+			;
+	}
+
+	prom_init_cmdline(fw_arg0, (LONG *)fw_arg1);
+	prom_identify_arch();
+	printk(KERN_INFO "PROMLIB: ARC firmware Version %d Revision %d\n",
+	       pb->ver, pb->rev);
+	prom_meminit();
+
+#ifdef DEBUG_PROM_INIT
+	pr_info("Press a key to reboot\n");
+	ArcRead(0, &c, 1, &cnt);
+	ArcEnterInteractiveMode();
+#endif
+}
diff --git a/arch/mips/fw/arc/memory.c b/arch/mips/fw/arc/memory.c
new file mode 100644
index 000000000..66188739f
--- /dev/null
+++ b/arch/mips/fw/arc/memory.c
@@ -0,0 +1,192 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * memory.c: PROM library functions for acquiring/using memory descriptors
+ *	     given to us from the ARCS firmware.
+ *
+ * Copyright (C) 1996 by David S. Miller
+ * Copyright (C) 1999, 2000, 2001 by Ralf Baechle
+ * Copyright (C) 1999, 2000 by Silicon Graphics, Inc.
+ *
+ * PROM library functions for acquiring/using memory descriptors given to us
+ * from the ARCS firmware.  This is only used when CONFIG_ARC_MEMORY is set
+ * because on some machines like SGI IP27 the ARC memory configuration data
+ * completely bogus and alternate easier to use mechanisms are available.
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/sched.h>
+#include <linux/mm.h>
+#include <linux/memblock.h>
+#include <linux/swap.h>
+
+#include <asm/sgialib.h>
+#include <asm/page.h>
+#include <asm/bootinfo.h>
+
+#undef DEBUG
+
+#define MAX_PROM_MEM 5
+static phys_addr_t prom_mem_base[MAX_PROM_MEM] __initdata;
+static phys_addr_t prom_mem_size[MAX_PROM_MEM] __initdata;
+static unsigned int nr_prom_mem __initdata;
+
+/*
+ * For ARC firmware memory functions the unit of measuring memory is always
+ * a 4k page of memory
+ */
+#define ARC_PAGE_SHIFT	12
+
+struct linux_mdesc * __init ArcGetMemoryDescriptor(struct linux_mdesc *Current)
+{
+	return (struct linux_mdesc *) ARC_CALL1(get_mdesc, Current);
+}
+
+#ifdef DEBUG /* convenient for debugging */
+static char *arcs_mtypes[8] = {
+	"Exception Block",
+	"ARCS Romvec Page",
+	"Free/Contig RAM",
+	"Generic Free RAM",
+	"Bad Memory",
+	"Standalone Program Pages",
+	"ARCS Temp Storage Area",
+	"ARCS Permanent Storage Area"
+};
+
+static char *arc_mtypes[8] = {
+	"Exception Block",
+	"SystemParameterBlock",
+	"FreeMemory",
+	"Bad Memory",
+	"LoadedProgram",
+	"FirmwareTemporary",
+	"FirmwarePermanent",
+	"FreeContiguous"
+};
+#define mtypes(a) (prom_flags & PROM_FLAG_ARCS) ? arcs_mtypes[a.arcs] \
+						: arc_mtypes[a.arc]
+#endif
+
+enum {
+	mem_free, mem_prom_used, mem_reserved
+};
+
+static inline int memtype_classify_arcs(union linux_memtypes type)
+{
+	switch (type.arcs) {
+	case arcs_fcontig:
+	case arcs_free:
+		return mem_free;
+	case arcs_atmp:
+		return mem_prom_used;
+	case arcs_eblock:
+	case arcs_rvpage:
+	case arcs_bmem:
+	case arcs_prog:
+	case arcs_aperm:
+		return mem_reserved;
+	default:
+		BUG();
+	}
+	while(1);				/* Nuke warning.  */
+}
+
+static inline int memtype_classify_arc(union linux_memtypes type)
+{
+	switch (type.arc) {
+	case arc_free:
+	case arc_fcontig:
+		return mem_free;
+	case arc_atmp:
+		return mem_prom_used;
+	case arc_eblock:
+	case arc_rvpage:
+	case arc_bmem:
+	case arc_prog:
+	case arc_aperm:
+		return mem_reserved;
+	default:
+		BUG();
+	}
+	while(1);				/* Nuke warning.  */
+}
+
+static int __init prom_memtype_classify(union linux_memtypes type)
+{
+	if (prom_flags & PROM_FLAG_ARCS)	/* SGI is ``different'' ... */
+		return memtype_classify_arcs(type);
+
+	return memtype_classify_arc(type);
+}
+
+void __weak __init prom_meminit(void)
+{
+	struct linux_mdesc *p;
+
+#ifdef DEBUG
+	int i = 0;
+
+	printk("ARCS MEMORY DESCRIPTOR dump:\n");
+	p = ArcGetMemoryDescriptor(PROM_NULL_MDESC);
+	while(p) {
+		printk("[%d,%p]: base<%08lx> pages<%08lx> type<%s>\n",
+		       i, p, p->base, p->pages, mtypes(p->type));
+		p = ArcGetMemoryDescriptor(p);
+		i++;
+	}
+#endif
+
+	nr_prom_mem = 0;
+	p = PROM_NULL_MDESC;
+	while ((p = ArcGetMemoryDescriptor(p))) {
+		unsigned long base, size;
+		long type;
+
+		base = p->base << ARC_PAGE_SHIFT;
+		size = p->pages << ARC_PAGE_SHIFT;
+		type = prom_memtype_classify(p->type);
+
+		/* ignore mirrored RAM on IP28/IP30 */
+		if (base < PHYS_OFFSET)
+			continue;
+
+		memblock_add(base, size);
+
+		if (type == mem_reserved)
+			memblock_reserve(base, size);
+
+		if (type == mem_prom_used) {
+			memblock_reserve(base, size);
+			if (nr_prom_mem >= 5) {
+				pr_err("Too many ROM DATA regions");
+				continue;
+			}
+			prom_mem_base[nr_prom_mem] = base;
+			prom_mem_size[nr_prom_mem] = size;
+			nr_prom_mem++;
+		}
+	}
+}
+
+void __weak __init prom_cleanup(void)
+{
+}
+
+void __init prom_free_prom_memory(void)
+{
+	int i;
+
+	if (prom_flags & PROM_FLAG_DONT_FREE_TEMP)
+		return;
+
+	for (i = 0; i < nr_prom_mem; i++) {
+		free_init_pages("prom memory",
+			prom_mem_base[i], prom_mem_base[i] + prom_mem_size[i]);
+	}
+	/*
+	 * at this point it isn't safe to call PROM functions
+	 * give platforms a way to do PROM cleanups
+	 */
+	prom_cleanup();
+}
diff --git a/arch/mips/fw/arc/misc.c b/arch/mips/fw/arc/misc.c
new file mode 100644
index 000000000..d5b2d5901
--- /dev/null
+++ b/arch/mips/fw/arc/misc.c
@@ -0,0 +1,36 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Miscellaneous ARCS PROM routines.
+ *
+ * Copyright (C) 1996 David S. Miller (davem@davemloft.net)
+ * Copyright (C) 1999 Ralf Baechle (ralf@gnu.org)
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ */
+#include <linux/compiler.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/irqflags.h>
+
+#include <asm/bcache.h>
+
+#include <asm/fw/arc/types.h>
+#include <asm/sgialib.h>
+#include <asm/bootinfo.h>
+
+VOID __noreturn
+ArcEnterInteractiveMode(VOID)
+{
+	bc_disable();
+	local_irq_disable();
+	ARC_CALL0(imode);
+
+	unreachable();
+}
+
+DISPLAY_STATUS * __init ArcGetDisplayStatus(ULONG FileID)
+{
+	return (DISPLAY_STATUS *) ARC_CALL1(GetDisplayStatus, FileID);
+}
diff --git a/arch/mips/fw/arc/promlib.c b/arch/mips/fw/arc/promlib.c
new file mode 100644
index 000000000..5e9e840a9
--- /dev/null
+++ b/arch/mips/fw/arc/promlib.c
@@ -0,0 +1,61 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1996 David S. Miller (dm@sgi.com)
+ * Compatibility with board caches, Ulf Carlsson
+ */
+#include <linux/kernel.h>
+#include <asm/sgialib.h>
+#include <asm/bcache.h>
+#include <asm/setup.h>
+
+#if defined(CONFIG_64BIT) && defined(CONFIG_FW_ARC32)
+/*
+ * For 64bit kernels working with a 32bit ARC PROM pointer arguments
+ * for ARC calls need to reside in CKEG0/1. But as soon as the kernel
+ * switches to it's first kernel thread stack is set to an address in
+ * XKPHYS, so anything on stack can't be used anymore. This is solved
+ * by using a * static declartion variables are put into BSS, which is
+ * linked to a CKSEG0 address. Since this is only used on UP platforms
+ * there is not spinlock needed
+ */
+#define O32_STATIC	static
+#else
+#define O32_STATIC
+#endif
+
+/*
+ * IP22 boardcache is not compatible with board caches.	 Thus we disable it
+ * during romvec action.  Since r4xx0.c is always compiled and linked with your
+ * kernel, this shouldn't cause any harm regardless what MIPS processor you
+ * have.
+ *
+ * The ARC write and read functions seem to interfere with the serial lines
+ * in some way. You should be careful with them.
+ */
+
+void prom_putchar(char c)
+{
+	O32_STATIC ULONG cnt;
+	O32_STATIC CHAR it;
+
+	it = c;
+
+	bc_disable();
+	ArcWrite(1, &it, 1, &cnt);
+	bc_enable();
+}
+
+char prom_getchar(void)
+{
+	O32_STATIC ULONG cnt;
+	O32_STATIC CHAR c;
+
+	bc_disable();
+	ArcRead(0, &c, 1, &cnt);
+	bc_enable();
+
+	return c;
+}
diff --git a/arch/mips/fw/cfe/Makefile b/arch/mips/fw/cfe/Makefile
new file mode 100644
index 000000000..55b77633e
--- /dev/null
+++ b/arch/mips/fw/cfe/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Makefile for the Broadcom Common Firmware Environment support
+#
+
+lib-y += cfe_api.o
diff --git a/arch/mips/fw/cfe/cfe_api.c b/arch/mips/fw/cfe/cfe_api.c
new file mode 100644
index 000000000..dcdfd962d
--- /dev/null
+++ b/arch/mips/fw/cfe/cfe_api.c
@@ -0,0 +1,480 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2000, 2001, 2002 Broadcom Corporation
+ */
+
+/*
+ *
+ * Broadcom Common Firmware Environment (CFE)
+ *
+ * This module contains device function stubs (small routines to
+ * call the standard "iocb" interface entry point to CFE).
+ * There should be one routine here per iocb function call.
+ *
+ * Authors:  Mitch Lichtenberg, Chris Demetriou
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/printk.h>
+#include <asm/mipsregs.h>
+#include <asm/fw/cfe/cfe_api.h>
+#include "cfe_api_int.h"
+
+unsigned long __initdata cfe_seal;
+
+/* Cast from a native pointer to a cfe_xptr_t and back.	 */
+#define XPTR_FROM_NATIVE(n)	((cfe_xptr_t) (intptr_t) (n))
+#define NATIVE_FROM_XPTR(x)	((void *) (intptr_t) (x))
+
+int cfe_iocb_dispatch(struct cfe_xiocb *xiocb);
+
+/*
+ * Declare the dispatch function with args of "intptr_t".
+ * This makes sure whatever model we're compiling in
+ * puts the pointers in a single register.  For example,
+ * combining -mlong64 and -mips1 or -mips2 would lead to
+ * trouble, since the handle and IOCB pointer will be
+ * passed in two registers each, and CFE expects one.
+ */
+
+static int (*cfe_dispfunc) (intptr_t handle, intptr_t xiocb);
+static u64 cfe_handle;
+
+int cfe_init(u64 handle, u64 ept)
+{
+	cfe_dispfunc = NATIVE_FROM_XPTR(ept);
+	cfe_handle = handle;
+	return 0;
+}
+
+int cfe_iocb_dispatch(struct cfe_xiocb * xiocb)
+{
+	if (!cfe_dispfunc)
+		return -1;
+	return (*cfe_dispfunc) ((intptr_t) cfe_handle, (intptr_t) xiocb);
+}
+
+int cfe_close(int handle)
+{
+	struct cfe_xiocb xiocb;
+
+	xiocb.xiocb_fcode = CFE_CMD_DEV_CLOSE;
+	xiocb.xiocb_status = 0;
+	xiocb.xiocb_handle = handle;
+	xiocb.xiocb_flags = 0;
+	xiocb.xiocb_psize = 0;
+
+	cfe_iocb_dispatch(&xiocb);
+
+	return xiocb.xiocb_status;
+
+}
+
+int cfe_cpu_start(int cpu, void (*fn) (void), long sp, long gp, long a1)
+{
+	struct cfe_xiocb xiocb;
+
+	xiocb.xiocb_fcode = CFE_CMD_FW_CPUCTL;
+	xiocb.xiocb_status = 0;
+	xiocb.xiocb_handle = 0;
+	xiocb.xiocb_flags = 0;
+	xiocb.xiocb_psize = sizeof(struct xiocb_cpuctl);
+	xiocb.plist.xiocb_cpuctl.cpu_number = cpu;
+	xiocb.plist.xiocb_cpuctl.cpu_command = CFE_CPU_CMD_START;
+	xiocb.plist.xiocb_cpuctl.gp_val = gp;
+	xiocb.plist.xiocb_cpuctl.sp_val = sp;
+	xiocb.plist.xiocb_cpuctl.a1_val = a1;
+	xiocb.plist.xiocb_cpuctl.start_addr = (long) fn;
+
+	cfe_iocb_dispatch(&xiocb);
+
+	return xiocb.xiocb_status;
+}
+
+int cfe_cpu_stop(int cpu)
+{
+	struct cfe_xiocb xiocb;
+
+	xiocb.xiocb_fcode = CFE_CMD_FW_CPUCTL;
+	xiocb.xiocb_status = 0;
+	xiocb.xiocb_handle = 0;
+	xiocb.xiocb_flags = 0;
+	xiocb.xiocb_psize = sizeof(struct xiocb_cpuctl);
+	xiocb.plist.xiocb_cpuctl.cpu_number = cpu;
+	xiocb.plist.xiocb_cpuctl.cpu_command = CFE_CPU_CMD_STOP;
+
+	cfe_iocb_dispatch(&xiocb);
+
+	return xiocb.xiocb_status;
+}
+
+int cfe_enumenv(int idx, char *name, int namelen, char *val, int vallen)
+{
+	struct cfe_xiocb xiocb;
+
+	xiocb.xiocb_fcode = CFE_CMD_ENV_SET;
+	xiocb.xiocb_status = 0;
+	xiocb.xiocb_handle = 0;
+	xiocb.xiocb_flags = 0;
+	xiocb.xiocb_psize = sizeof(struct xiocb_envbuf);
+	xiocb.plist.xiocb_envbuf.enum_idx = idx;
+	xiocb.plist.xiocb_envbuf.name_ptr = XPTR_FROM_NATIVE(name);
+	xiocb.plist.xiocb_envbuf.name_length = namelen;
+	xiocb.plist.xiocb_envbuf.val_ptr = XPTR_FROM_NATIVE(val);
+	xiocb.plist.xiocb_envbuf.val_length = vallen;
+
+	cfe_iocb_dispatch(&xiocb);
+
+	return xiocb.xiocb_status;
+}
+
+int
+cfe_enummem(int idx, int flags, u64 *start, u64 *length, u64 *type)
+{
+	struct cfe_xiocb xiocb;
+
+	xiocb.xiocb_fcode = CFE_CMD_FW_MEMENUM;
+	xiocb.xiocb_status = 0;
+	xiocb.xiocb_handle = 0;
+	xiocb.xiocb_flags = flags;
+	xiocb.xiocb_psize = sizeof(struct xiocb_meminfo);
+	xiocb.plist.xiocb_meminfo.mi_idx = idx;
+
+	cfe_iocb_dispatch(&xiocb);
+
+	if (xiocb.xiocb_status < 0)
+		return xiocb.xiocb_status;
+
+	*start = xiocb.plist.xiocb_meminfo.mi_addr;
+	*length = xiocb.plist.xiocb_meminfo.mi_size;
+	*type = xiocb.plist.xiocb_meminfo.mi_type;
+
+	return 0;
+}
+
+int cfe_exit(int warm, int status)
+{
+	struct cfe_xiocb xiocb;
+
+	xiocb.xiocb_fcode = CFE_CMD_FW_RESTART;
+	xiocb.xiocb_status = 0;
+	xiocb.xiocb_handle = 0;
+	xiocb.xiocb_flags = warm ? CFE_FLG_WARMSTART : 0;
+	xiocb.xiocb_psize = sizeof(struct xiocb_exitstat);
+	xiocb.plist.xiocb_exitstat.status = status;
+
+	cfe_iocb_dispatch(&xiocb);
+
+	return xiocb.xiocb_status;
+}
+
+int cfe_flushcache(int flg)
+{
+	struct cfe_xiocb xiocb;
+
+	xiocb.xiocb_fcode = CFE_CMD_FW_FLUSHCACHE;
+	xiocb.xiocb_status = 0;
+	xiocb.xiocb_handle = 0;
+	xiocb.xiocb_flags = flg;
+	xiocb.xiocb_psize = 0;
+
+	cfe_iocb_dispatch(&xiocb);
+
+	return xiocb.xiocb_status;
+}
+
+int cfe_getdevinfo(char *name)
+{
+	struct cfe_xiocb xiocb;
+
+	xiocb.xiocb_fcode = CFE_CMD_DEV_GETINFO;
+	xiocb.xiocb_status = 0;
+	xiocb.xiocb_handle = 0;
+	xiocb.xiocb_flags = 0;
+	xiocb.xiocb_psize = sizeof(struct xiocb_buffer);
+	xiocb.plist.xiocb_buffer.buf_offset = 0;
+	xiocb.plist.xiocb_buffer.buf_ptr = XPTR_FROM_NATIVE(name);
+	xiocb.plist.xiocb_buffer.buf_length = strlen(name);
+
+	cfe_iocb_dispatch(&xiocb);
+
+	if (xiocb.xiocb_status < 0)
+		return xiocb.xiocb_status;
+	return xiocb.plist.xiocb_buffer.buf_ioctlcmd;
+}
+
+int cfe_getenv(char *name, char *dest, int destlen)
+{
+	struct cfe_xiocb xiocb;
+
+	*dest = 0;
+
+	xiocb.xiocb_fcode = CFE_CMD_ENV_GET;
+	xiocb.xiocb_status = 0;
+	xiocb.xiocb_handle = 0;
+	xiocb.xiocb_flags = 0;
+	xiocb.xiocb_psize = sizeof(struct xiocb_envbuf);
+	xiocb.plist.xiocb_envbuf.enum_idx = 0;
+	xiocb.plist.xiocb_envbuf.name_ptr = XPTR_FROM_NATIVE(name);
+	xiocb.plist.xiocb_envbuf.name_length = strlen(name);
+	xiocb.plist.xiocb_envbuf.val_ptr = XPTR_FROM_NATIVE(dest);
+	xiocb.plist.xiocb_envbuf.val_length = destlen;
+
+	cfe_iocb_dispatch(&xiocb);
+
+	return xiocb.xiocb_status;
+}
+
+int cfe_getfwinfo(cfe_fwinfo_t * info)
+{
+	struct cfe_xiocb xiocb;
+
+	xiocb.xiocb_fcode = CFE_CMD_FW_GETINFO;
+	xiocb.xiocb_status = 0;
+	xiocb.xiocb_handle = 0;
+	xiocb.xiocb_flags = 0;
+	xiocb.xiocb_psize = sizeof(struct xiocb_fwinfo);
+
+	cfe_iocb_dispatch(&xiocb);
+
+	if (xiocb.xiocb_status < 0)
+		return xiocb.xiocb_status;
+
+	info->fwi_version = xiocb.plist.xiocb_fwinfo.fwi_version;
+	info->fwi_totalmem = xiocb.plist.xiocb_fwinfo.fwi_totalmem;
+	info->fwi_flags = xiocb.plist.xiocb_fwinfo.fwi_flags;
+	info->fwi_boardid = xiocb.plist.xiocb_fwinfo.fwi_boardid;
+	info->fwi_bootarea_va = xiocb.plist.xiocb_fwinfo.fwi_bootarea_va;
+	info->fwi_bootarea_pa = xiocb.plist.xiocb_fwinfo.fwi_bootarea_pa;
+	info->fwi_bootarea_size =
+	    xiocb.plist.xiocb_fwinfo.fwi_bootarea_size;
+
+	return 0;
+}
+
+int cfe_getstdhandle(int flg)
+{
+	struct cfe_xiocb xiocb;
+
+	xiocb.xiocb_fcode = CFE_CMD_DEV_GETHANDLE;
+	xiocb.xiocb_status = 0;
+	xiocb.xiocb_handle = 0;
+	xiocb.xiocb_flags = flg;
+	xiocb.xiocb_psize = 0;
+
+	cfe_iocb_dispatch(&xiocb);
+
+	if (xiocb.xiocb_status < 0)
+		return xiocb.xiocb_status;
+	return xiocb.xiocb_handle;
+}
+
+int64_t
+cfe_getticks(void)
+{
+	struct cfe_xiocb xiocb;
+
+	xiocb.xiocb_fcode = CFE_CMD_FW_GETTIME;
+	xiocb.xiocb_status = 0;
+	xiocb.xiocb_handle = 0;
+	xiocb.xiocb_flags = 0;
+	xiocb.xiocb_psize = sizeof(struct xiocb_time);
+	xiocb.plist.xiocb_time.ticks = 0;
+
+	cfe_iocb_dispatch(&xiocb);
+
+	return xiocb.plist.xiocb_time.ticks;
+
+}
+
+int cfe_inpstat(int handle)
+{
+	struct cfe_xiocb xiocb;
+
+	xiocb.xiocb_fcode = CFE_CMD_DEV_INPSTAT;
+	xiocb.xiocb_status = 0;
+	xiocb.xiocb_handle = handle;
+	xiocb.xiocb_flags = 0;
+	xiocb.xiocb_psize = sizeof(struct xiocb_inpstat);
+	xiocb.plist.xiocb_inpstat.inp_status = 0;
+
+	cfe_iocb_dispatch(&xiocb);
+
+	if (xiocb.xiocb_status < 0)
+		return xiocb.xiocb_status;
+	return xiocb.plist.xiocb_inpstat.inp_status;
+}
+
+int
+cfe_ioctl(int handle, unsigned int ioctlnum, unsigned char *buffer,
+	  int length, int *retlen, u64 offset)
+{
+	struct cfe_xiocb xiocb;
+
+	xiocb.xiocb_fcode = CFE_CMD_DEV_IOCTL;
+	xiocb.xiocb_status = 0;
+	xiocb.xiocb_handle = handle;
+	xiocb.xiocb_flags = 0;
+	xiocb.xiocb_psize = sizeof(struct xiocb_buffer);
+	xiocb.plist.xiocb_buffer.buf_offset = offset;
+	xiocb.plist.xiocb_buffer.buf_ioctlcmd = ioctlnum;
+	xiocb.plist.xiocb_buffer.buf_ptr = XPTR_FROM_NATIVE(buffer);
+	xiocb.plist.xiocb_buffer.buf_length = length;
+
+	cfe_iocb_dispatch(&xiocb);
+
+	if (retlen)
+		*retlen = xiocb.plist.xiocb_buffer.buf_retlen;
+	return xiocb.xiocb_status;
+}
+
+int cfe_open(char *name)
+{
+	struct cfe_xiocb xiocb;
+
+	xiocb.xiocb_fcode = CFE_CMD_DEV_OPEN;
+	xiocb.xiocb_status = 0;
+	xiocb.xiocb_handle = 0;
+	xiocb.xiocb_flags = 0;
+	xiocb.xiocb_psize = sizeof(struct xiocb_buffer);
+	xiocb.plist.xiocb_buffer.buf_offset = 0;
+	xiocb.plist.xiocb_buffer.buf_ptr = XPTR_FROM_NATIVE(name);
+	xiocb.plist.xiocb_buffer.buf_length = strlen(name);
+
+	cfe_iocb_dispatch(&xiocb);
+
+	if (xiocb.xiocb_status < 0)
+		return xiocb.xiocb_status;
+	return xiocb.xiocb_handle;
+}
+
+int cfe_read(int handle, unsigned char *buffer, int length)
+{
+	return cfe_readblk(handle, 0, buffer, length);
+}
+
+int cfe_readblk(int handle, s64 offset, unsigned char *buffer, int length)
+{
+	struct cfe_xiocb xiocb;
+
+	xiocb.xiocb_fcode = CFE_CMD_DEV_READ;
+	xiocb.xiocb_status = 0;
+	xiocb.xiocb_handle = handle;
+	xiocb.xiocb_flags = 0;
+	xiocb.xiocb_psize = sizeof(struct xiocb_buffer);
+	xiocb.plist.xiocb_buffer.buf_offset = offset;
+	xiocb.plist.xiocb_buffer.buf_ptr = XPTR_FROM_NATIVE(buffer);
+	xiocb.plist.xiocb_buffer.buf_length = length;
+
+	cfe_iocb_dispatch(&xiocb);
+
+	if (xiocb.xiocb_status < 0)
+		return xiocb.xiocb_status;
+	return xiocb.plist.xiocb_buffer.buf_retlen;
+}
+
+int cfe_setenv(char *name, char *val)
+{
+	struct cfe_xiocb xiocb;
+
+	xiocb.xiocb_fcode = CFE_CMD_ENV_SET;
+	xiocb.xiocb_status = 0;
+	xiocb.xiocb_handle = 0;
+	xiocb.xiocb_flags = 0;
+	xiocb.xiocb_psize = sizeof(struct xiocb_envbuf);
+	xiocb.plist.xiocb_envbuf.enum_idx = 0;
+	xiocb.plist.xiocb_envbuf.name_ptr = XPTR_FROM_NATIVE(name);
+	xiocb.plist.xiocb_envbuf.name_length = strlen(name);
+	xiocb.plist.xiocb_envbuf.val_ptr = XPTR_FROM_NATIVE(val);
+	xiocb.plist.xiocb_envbuf.val_length = strlen(val);
+
+	cfe_iocb_dispatch(&xiocb);
+
+	return xiocb.xiocb_status;
+}
+
+int cfe_write(int handle, const char *buffer, int length)
+{
+	return cfe_writeblk(handle, 0, buffer, length);
+}
+
+int cfe_writeblk(int handle, s64 offset, const char *buffer, int length)
+{
+	struct cfe_xiocb xiocb;
+
+	xiocb.xiocb_fcode = CFE_CMD_DEV_WRITE;
+	xiocb.xiocb_status = 0;
+	xiocb.xiocb_handle = handle;
+	xiocb.xiocb_flags = 0;
+	xiocb.xiocb_psize = sizeof(struct xiocb_buffer);
+	xiocb.plist.xiocb_buffer.buf_offset = offset;
+	xiocb.plist.xiocb_buffer.buf_ptr = XPTR_FROM_NATIVE(buffer);
+	xiocb.plist.xiocb_buffer.buf_length = length;
+
+	cfe_iocb_dispatch(&xiocb);
+
+	if (xiocb.xiocb_status < 0)
+		return xiocb.xiocb_status;
+	return xiocb.plist.xiocb_buffer.buf_retlen;
+}
+
+void __init cfe_die(char *fmt, ...)
+{
+	unsigned int prid, __maybe_unused rev;
+	char msg[128];
+	va_list ap;
+	int handle;
+	unsigned int count;
+
+	va_start(ap, fmt);
+	vsprintf(msg, fmt, ap);
+	strcat(msg, "\r\n");
+
+	if (cfe_seal != CFE_EPTSEAL)
+		goto no_cfe;
+
+	prid = read_c0_prid();
+	if ((prid & PRID_COMP_MASK) != PRID_COMP_BROADCOM)
+		goto no_cfe;
+
+	rev = prid & PRID_REV_MASK;
+
+	/* disable XKS01 so that CFE can access the registers */
+	switch (prid & PRID_IMP_MASK) {
+#ifdef CONFIG_CPU_BMIPS4380
+	case PRID_IMP_BMIPS43XX:
+		if (rev >= PRID_REV_BMIPS4380_LO &&
+		    rev <= PRID_REV_BMIPS4380_HI)
+			__write_32bit_c0_register($22, 3,
+				__read_32bit_c0_register($22, 3) & ~BIT(12));
+		break;
+#endif
+#ifdef CONFIG_CPU_BMIPS5000
+	case PRID_IMP_BMIPS5000:
+	case PRID_IMP_BMIPS5200:
+		__write_32bit_c0_register($22, 5,
+			__read_32bit_c0_register($22, 5) & ~BIT(8));
+		break;
+#endif
+	default:
+		break;
+	}
+
+	handle = cfe_getstdhandle(CFE_STDHANDLE_CONSOLE);
+	if (handle < 0)
+		goto no_cfe;
+
+	cfe_write(handle, msg, strlen(msg));
+
+	for (count = 0; count < 0x7fffffff; count++)
+		mb();
+	cfe_exit(0, 1);
+	while (1)
+		;
+
+no_cfe:
+	/* probably won't print anywhere useful */
+	panic("%s", msg);
+
+	va_end(ap);
+}
diff --git a/arch/mips/fw/cfe/cfe_api_int.h b/arch/mips/fw/cfe/cfe_api_int.h
new file mode 100644
index 000000000..61a665d44
--- /dev/null
+++ b/arch/mips/fw/cfe/cfe_api_int.h
@@ -0,0 +1,135 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2000, 2001, 2002 Broadcom Corporation
+ */
+#ifndef CFE_API_INT_H
+#define CFE_API_INT_H
+
+/*
+ * Constants.
+ */
+#define CFE_CMD_FW_GETINFO	0
+#define CFE_CMD_FW_RESTART	1
+#define CFE_CMD_FW_BOOT		2
+#define CFE_CMD_FW_CPUCTL	3
+#define CFE_CMD_FW_GETTIME      4
+#define CFE_CMD_FW_MEMENUM	5
+#define CFE_CMD_FW_FLUSHCACHE	6
+
+#define CFE_CMD_DEV_GETHANDLE	9
+#define CFE_CMD_DEV_ENUM	10
+#define CFE_CMD_DEV_OPEN	11
+#define CFE_CMD_DEV_INPSTAT	12
+#define CFE_CMD_DEV_READ	13
+#define CFE_CMD_DEV_WRITE	14
+#define CFE_CMD_DEV_IOCTL	15
+#define CFE_CMD_DEV_CLOSE	16
+#define CFE_CMD_DEV_GETINFO	17
+
+#define CFE_CMD_ENV_ENUM	20
+#define CFE_CMD_ENV_GET		22
+#define CFE_CMD_ENV_SET		23
+#define CFE_CMD_ENV_DEL		24
+
+#define CFE_CMD_MAX		32
+
+#define CFE_CMD_VENDOR_USE	0x8000	/* codes above this are for customer use */
+
+/*
+ * Structures.
+ */
+
+/* eeek, signed "pointers" */
+typedef s64 cfe_xptr_t;
+
+struct xiocb_buffer {
+	u64 buf_offset;		/* offset on device (bytes) */
+	cfe_xptr_t  buf_ptr;		/* pointer to a buffer */
+	u64 buf_length;		/* length of this buffer */
+	u64 buf_retlen;		/* returned length (for read ops) */
+	u64 buf_ioctlcmd;	/* IOCTL command (used only for IOCTLs) */
+};
+
+struct xiocb_inpstat {
+	u64 inp_status;		/* 1 means input available */
+};
+
+struct xiocb_envbuf {
+	s64 enum_idx;		/* 0-based enumeration index */
+	cfe_xptr_t name_ptr;		/* name string buffer */
+	s64 name_length;		/* size of name buffer */
+	cfe_xptr_t val_ptr;		/* value string buffer */
+	s64 val_length;		/* size of value string buffer */
+};
+
+struct xiocb_cpuctl {
+	u64 cpu_number;		/* cpu number to control */
+	u64 cpu_command;	/* command to issue to CPU */
+	u64 start_addr;		/* CPU start address */
+	u64 gp_val;		/* starting GP value */
+	u64 sp_val;		/* starting SP value */
+	u64 a1_val;		/* starting A1 value */
+};
+
+struct xiocb_time {
+	s64 ticks;		/* current time in ticks */
+};
+
+struct xiocb_exitstat{
+	s64 status;
+};
+
+struct xiocb_meminfo {
+	s64 mi_idx;		/* 0-based enumeration index */
+	s64 mi_type;		/* type of memory block */
+	u64 mi_addr;		/* physical start address */
+	u64 mi_size;		/* block size */
+};
+
+struct xiocb_fwinfo {
+	s64 fwi_version;		/* major, minor, eco version */
+	s64 fwi_totalmem;	/* total installed mem */
+	s64 fwi_flags;		/* various flags */
+	s64 fwi_boardid;		/* board ID */
+	s64 fwi_bootarea_va;	/* VA of boot area */
+	s64 fwi_bootarea_pa;	/* PA of boot area */
+	s64 fwi_bootarea_size;	/* size of boot area */
+	s64 fwi_reserved1;
+	s64 fwi_reserved2;
+	s64 fwi_reserved3;
+};
+
+struct cfe_xiocb {
+	u64 xiocb_fcode;	/* IOCB function code */
+	s64 xiocb_status;	/* return status */
+	s64 xiocb_handle;	/* file/device handle */
+	u64 xiocb_flags;	/* flags for this IOCB */
+	u64 xiocb_psize;	/* size of parameter list */
+	union {
+		/* buffer parameters */
+		struct xiocb_buffer xiocb_buffer;
+
+		/* input status parameters */
+		struct xiocb_inpstat xiocb_inpstat;
+
+		/* environment function parameters */
+		struct xiocb_envbuf xiocb_envbuf;
+
+		/* CPU control parameters */
+		struct xiocb_cpuctl xiocb_cpuctl;
+
+		/* timer parameters */
+		struct xiocb_time xiocb_time;
+
+		/* memory arena info parameters */
+		struct xiocb_meminfo xiocb_meminfo;
+
+		/* firmware information */
+		struct xiocb_fwinfo xiocb_fwinfo;
+
+		/* Exit Status */
+		struct xiocb_exitstat xiocb_exitstat;
+	} plist;
+};
+
+#endif /* CFE_API_INT_H */
diff --git a/arch/mips/fw/lib/Makefile b/arch/mips/fw/lib/Makefile
new file mode 100644
index 000000000..cf9634548
--- /dev/null
+++ b/arch/mips/fw/lib/Makefile
@@ -0,0 +1,8 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Makefile for generic prom monitor library routines under Linux.
+#
+
+lib-y			+= cmdline.o
+
+lib-$(CONFIG_64BIT)	+= call_o32.o
diff --git a/arch/mips/fw/lib/call_o32.S b/arch/mips/fw/lib/call_o32.S
new file mode 100644
index 000000000..ee856709e
--- /dev/null
+++ b/arch/mips/fw/lib/call_o32.S
@@ -0,0 +1,104 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ *	O32 interface for the 64 (or N32) ABI.
+ *
+ *	Copyright (C) 2002, 2014  Maciej W. Rozycki
+ */
+
+#include <asm/asm.h>
+#include <asm/regdef.h>
+
+/* O32 register size.  */
+#define O32_SZREG	4
+/* Maximum number of arguments supported.  Must be even!  */
+#define O32_ARGC	32
+/* Number of static registers we save.  */
+#define O32_STATC	11
+/* Argument area frame size.  */
+#define O32_ARGSZ	(O32_SZREG * O32_ARGC)
+/* Static register save area frame size.  */
+#define O32_STATSZ	(SZREG * O32_STATC)
+/* Stack pointer register save area frame size.  */
+#define O32_SPSZ	SZREG
+/* Combined area frame size.  */
+#define O32_FRAMESZ	(O32_ARGSZ + O32_SPSZ + O32_STATSZ)
+/* Switched stack frame size.  */
+#define O32_NFRAMESZ	(O32_ARGSZ + O32_SPSZ)
+
+		.text
+
+/*
+ * O32 function call dispatcher, for interfacing 32-bit ROM routines.
+ *
+ * The standard 64 (N32) calling sequence is supported, with a0 holding
+ * a function pointer, a1 a pointer to the new stack to call the
+ * function with or 0 if no stack switching is requested, a2-a7 -- the
+ * function call's first six arguments, and the stack -- the remaining
+ * arguments (up to O32_ARGC, including a2-a7).  Static registers, gp
+ * and fp are preserved, v0 holds the result.  This code relies on the
+ * called o32 function for sp and ra restoration and this dispatcher has
+ * to be placed in a KSEGx (or KUSEG) address space.  Any pointers
+ * passed have to point to addresses within one of these spaces as well.
+ */
+NESTED(call_o32, O32_FRAMESZ, ra)
+		REG_SUBU	sp,O32_FRAMESZ
+
+		REG_S		ra,O32_FRAMESZ-1*SZREG(sp)
+		REG_S		fp,O32_FRAMESZ-2*SZREG(sp)
+		REG_S		gp,O32_FRAMESZ-3*SZREG(sp)
+		REG_S		s7,O32_FRAMESZ-4*SZREG(sp)
+		REG_S		s6,O32_FRAMESZ-5*SZREG(sp)
+		REG_S		s5,O32_FRAMESZ-6*SZREG(sp)
+		REG_S		s4,O32_FRAMESZ-7*SZREG(sp)
+		REG_S		s3,O32_FRAMESZ-8*SZREG(sp)
+		REG_S		s2,O32_FRAMESZ-9*SZREG(sp)
+		REG_S		s1,O32_FRAMESZ-10*SZREG(sp)
+		REG_S		s0,O32_FRAMESZ-11*SZREG(sp)
+
+		move		jp,a0
+
+		move		fp,sp
+		beqz		a1,0f
+		REG_SUBU	fp,a1,O32_NFRAMESZ
+0:
+		REG_S		sp,O32_NFRAMESZ-1*SZREG(fp)
+
+		sll		a0,a2,zero
+		sll		a1,a3,zero
+		sll		a2,a4,zero
+		sll		a3,a5,zero
+		sw		a6,4*O32_SZREG(fp)
+		sw		a7,5*O32_SZREG(fp)
+
+		PTR_LA		t0,O32_FRAMESZ(sp)
+		PTR_LA		t1,6*O32_SZREG(fp)
+		li		t2,O32_ARGC-6
+1:
+		lw		t3,(t0)
+		REG_ADDU	t0,SZREG
+		sw		t3,(t1)
+		REG_SUBU	t2,1
+		REG_ADDU	t1,O32_SZREG
+		bnez		t2,1b
+
+		move		sp,fp
+
+		jalr		jp
+
+		REG_L		sp,O32_NFRAMESZ-1*SZREG(sp)
+
+		REG_L		s0,O32_FRAMESZ-11*SZREG(sp)
+		REG_L		s1,O32_FRAMESZ-10*SZREG(sp)
+		REG_L		s2,O32_FRAMESZ-9*SZREG(sp)
+		REG_L		s3,O32_FRAMESZ-8*SZREG(sp)
+		REG_L		s4,O32_FRAMESZ-7*SZREG(sp)
+		REG_L		s5,O32_FRAMESZ-6*SZREG(sp)
+		REG_L		s6,O32_FRAMESZ-5*SZREG(sp)
+		REG_L		s7,O32_FRAMESZ-4*SZREG(sp)
+		REG_L		gp,O32_FRAMESZ-3*SZREG(sp)
+		REG_L		fp,O32_FRAMESZ-2*SZREG(sp)
+		REG_L		ra,O32_FRAMESZ-1*SZREG(sp)
+
+		REG_ADDU	sp,O32_FRAMESZ
+		jr		ra
+END(call_o32)
diff --git a/arch/mips/fw/lib/cmdline.c b/arch/mips/fw/lib/cmdline.c
new file mode 100644
index 000000000..892765b74
--- /dev/null
+++ b/arch/mips/fw/lib/cmdline.c
@@ -0,0 +1,103 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2012 MIPS Technologies, Inc.  All rights reserved.
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/string.h>
+
+#include <asm/addrspace.h>
+#include <asm/fw/fw.h>
+
+int fw_argc;
+int *_fw_argv;
+int *_fw_envp;
+
+#ifndef CONFIG_HAVE_PLAT_FW_INIT_CMDLINE
+void __init fw_init_cmdline(void)
+{
+	int i;
+
+	/* Validate command line parameters. */
+	if ((fw_arg0 >= CKSEG0) || (fw_arg1 < CKSEG0)) {
+		fw_argc = 0;
+		_fw_argv = NULL;
+	} else {
+		fw_argc = (fw_arg0 & 0x0000ffff);
+		_fw_argv = (int *)fw_arg1;
+	}
+
+	/* Validate environment pointer. */
+	if (fw_arg2 < CKSEG0)
+		_fw_envp = NULL;
+	else
+		_fw_envp = (int *)fw_arg2;
+
+	for (i = 1; i < fw_argc; i++) {
+		strlcat(arcs_cmdline, fw_argv(i), COMMAND_LINE_SIZE);
+		if (i < (fw_argc - 1))
+			strlcat(arcs_cmdline, " ", COMMAND_LINE_SIZE);
+	}
+}
+#endif
+
+char * __init fw_getcmdline(void)
+{
+	return &(arcs_cmdline[0]);
+}
+
+char *fw_getenv(char *envname)
+{
+	char *result = NULL;
+
+	if (_fw_envp != NULL && fw_envp(0) != NULL) {
+		/*
+		 * Return a pointer to the given environment variable.
+		 * YAMON uses "name", "value" pairs, while U-Boot uses
+		 * "name=value".
+		 */
+		int i, yamon, index = 0;
+
+		yamon = (strchr(fw_envp(index), '=') == NULL);
+		i = strlen(envname);
+
+		while (fw_envp(index)) {
+			if (strncmp(envname, fw_envp(index), i) == 0) {
+				if (yamon) {
+					result = fw_envp(index + 1);
+					break;
+				} else if (fw_envp(index)[i] == '=') {
+					result = fw_envp(index) + i + 1;
+					break;
+				}
+			}
+
+			/* Increment array index. */
+			if (yamon)
+				index += 2;
+			else
+				index += 1;
+		}
+	}
+
+	return result;
+}
+
+unsigned long fw_getenvl(char *envname)
+{
+	unsigned long envl = 0UL;
+	char *str;
+	int tmp;
+
+	str = fw_getenv(envname);
+	if (str) {
+		tmp = kstrtoul(str, 0, &envl);
+		if (tmp)
+			envl = 0;
+	}
+
+	return envl;
+}
diff --git a/arch/mips/fw/sni/Makefile b/arch/mips/fw/sni/Makefile
new file mode 100644
index 000000000..e5ba8e86b
--- /dev/null
+++ b/arch/mips/fw/sni/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Makefile for the SNI prom monitor routines under Linux.
+#
+
+lib-$(CONFIG_FW_SNIPROM)	+= sniprom.o
diff --git a/arch/mips/fw/sni/sniprom.c b/arch/mips/fw/sni/sniprom.c
new file mode 100644
index 000000000..74975e115
--- /dev/null
+++ b/arch/mips/fw/sni/sniprom.c
@@ -0,0 +1,149 @@
+/*
+ * Big Endian PROM code for SNI RM machines
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2005-2006 Florian Lohoff (flo@rfc822.org)
+ * Copyright (C) 2005-2006 Thomas Bogendoerfer (tsbogend@alpha.franken.de)
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/memblock.h>
+#include <linux/string.h>
+#include <linux/console.h>
+
+#include <asm/addrspace.h>
+#include <asm/sni.h>
+#include <asm/mipsprom.h>
+#include <asm/mipsregs.h>
+#include <asm/bootinfo.h>
+#include <asm/setup.h>
+
+/* special SNI prom calls */
+/*
+ * This does not exist in all proms - SINIX compares
+ * the prom env variable "version" against "2.0008"
+ * or greater. If lesser it tries to probe interesting
+ * registers
+ */
+#define PROM_GET_MEMCONF	58
+#define PROM_GET_HWCONF		61
+
+#define PROM_VEC		(u64 *)CKSEG1ADDR(0x1fc00000)
+#define PROM_ENTRY(x)		(PROM_VEC + (x))
+
+#define ___prom_putchar		((int *(*)(int))PROM_ENTRY(PROM_PUTCHAR))
+#define ___prom_getenv		((char *(*)(char *))PROM_ENTRY(PROM_GETENV))
+#define ___prom_get_memconf	((void (*)(void *))PROM_ENTRY(PROM_GET_MEMCONF))
+#define ___prom_get_hwconf	((u32 (*)(void))PROM_ENTRY(PROM_GET_HWCONF))
+
+#ifdef CONFIG_64BIT
+
+/* O32 stack has to be 8-byte aligned. */
+static u64 o32_stk[4096];
+#define O32_STK	  (&o32_stk[ARRAY_SIZE(o32_stk)])
+
+#define __PROM_O32(fun, arg) fun arg __asm__(#fun); \
+				     __asm__(#fun " = call_o32")
+
+int   __PROM_O32(__prom_putchar, (int *(*)(int), void *, int));
+char *__PROM_O32(__prom_getenv, (char *(*)(char *), void *, char *));
+void  __PROM_O32(__prom_get_memconf, (void (*)(void *), void *, void *));
+u32   __PROM_O32(__prom_get_hwconf, (u32 (*)(void), void *));
+
+#define _prom_putchar(x)     __prom_putchar(___prom_putchar, O32_STK, x)
+#define _prom_getenv(x)	     __prom_getenv(___prom_getenv, O32_STK, x)
+#define _prom_get_memconf(x) __prom_get_memconf(___prom_get_memconf, O32_STK, x)
+#define _prom_get_hwconf()   __prom_get_hwconf(___prom_get_hwconf, O32_STK)
+
+#else
+#define _prom_putchar(x)     ___prom_putchar(x)
+#define _prom_getenv(x)	     ___prom_getenv(x)
+#define _prom_get_memconf(x) ___prom_get_memconf(x)
+#define _prom_get_hwconf(x)  ___prom_get_hwconf(x)
+#endif
+
+void prom_putchar(char c)
+{
+	_prom_putchar(c);
+}
+
+
+char *prom_getenv(char *s)
+{
+	return _prom_getenv(s);
+}
+
+void *prom_get_hwconf(void)
+{
+	u32 hwconf = _prom_get_hwconf();
+
+	if (hwconf == 0xffffffff)
+		return NULL;
+
+	return (void *)CKSEG1ADDR(hwconf);
+}
+
+/*
+ * /proc/cpuinfo system type
+ *
+ */
+char *system_type = "Unknown";
+const char *get_system_type(void)
+{
+	return system_type;
+}
+
+static void __init sni_mem_init(void)
+{
+	int i, memsize;
+	struct membank {
+		u32		size;
+		u32		base;
+		u32		size2;
+		u32		pad1;
+		u32		pad2;
+	} memconf[8];
+	int brd_type = *(unsigned char *)SNI_IDPROM_BRDTYPE;
+
+
+	/* MemSIZE from prom in 16MByte chunks */
+	memsize = *((unsigned char *) SNI_IDPROM_MEMSIZE) * 16;
+
+	pr_debug("IDProm memsize: %u MByte\n", memsize);
+
+	/* get memory bank layout from prom */
+	_prom_get_memconf(&memconf);
+
+	pr_debug("prom_get_mem_conf memory configuration:\n");
+	for (i = 0; i < 8 && memconf[i].size; i++) {
+		if (brd_type == SNI_BRD_PCI_TOWER ||
+		    brd_type == SNI_BRD_PCI_TOWER_CPLUS) {
+			if (memconf[i].base >= 0x20000000 &&
+			    memconf[i].base <  0x30000000)
+				memconf[i].base -= 0x20000000;
+		}
+		pr_debug("Bank%d: %08x @ %08x\n", i,
+			memconf[i].size, memconf[i].base);
+		memblock_add(memconf[i].base, memconf[i].size);
+	}
+}
+
+void __init prom_init(void)
+{
+	int argc = fw_arg0;
+	u32 *argv = (u32 *)CKSEG0ADDR(fw_arg1);
+	int i;
+
+	sni_mem_init();
+
+	/* copy prom cmdline parameters to kernel cmdline */
+	for (i = 1; i < argc; i++) {
+		strcat(arcs_cmdline, (char *)CKSEG0ADDR(argv[i]));
+		if (i < (argc - 1))
+			strcat(arcs_cmdline, " ");
+	}
+}
diff --git a/arch/mips/generic/Kconfig b/arch/mips/generic/Kconfig
new file mode 100644
index 000000000..7dc5b3821
--- /dev/null
+++ b/arch/mips/generic/Kconfig
@@ -0,0 +1,127 @@
+# SPDX-License-Identifier: GPL-2.0
+if MIPS_GENERIC_KERNEL
+
+config LEGACY_BOARDS
+	bool
+	help
+	  Select this from your board if the board must use a legacy, non-UHI,
+	  boot protocol. This will cause the kernel to scan through the list of
+	  supported machines calling their detect functions in turn if the
+	  kernel is booted without being provided with an FDT via the UHI
+	  boot protocol.
+
+config YAMON_DT_SHIM
+	bool
+	help
+	  Select this from your board if the board uses the YAMON bootloader
+	  and you wish to include code which helps translate various
+	  YAMON-provided environment variables into a device tree properties.
+
+comment "Legacy (non-UHI/non-FIT) Boards"
+
+config LEGACY_BOARD_SEAD3
+	bool "Support MIPS SEAD-3 boards"
+	select LEGACY_BOARDS
+	select YAMON_DT_SHIM
+	help
+	  Enable this to include support for booting on MIPS SEAD-3 FPGA-based
+	  development boards, which boot using a legacy boot protocol.
+
+comment "MSCC Ocelot doesn't work with SEAD3 enabled"
+	depends on LEGACY_BOARD_SEAD3
+
+config LEGACY_BOARD_OCELOT
+	bool "Legacy support for Ocelot based boards"
+	depends on LEGACY_BOARD_SEAD3=n
+	select LEGACY_BOARDS
+	select SOC_VCOREIII
+	select SYS_HAS_EARLY_PRINTK
+	select USE_GENERIC_EARLY_PRINTK_8250
+
+config SOC_VCOREIII
+	bool
+	select GPIOLIB
+	select MSCC_OCELOT_IRQ
+	select MSCC_OCELOT #will be removed when driver no more use it
+
+#Will be removed when the driver using it will be converted to SOC_VCOREIII
+config MSCC_OCELOT
+	bool
+
+comment "FIT/UHI Boards"
+
+config FIT_IMAGE_FDT_BOSTON
+	bool "Include FDT for MIPS Boston boards"
+	help
+	  Enable this to include the FDT for the MIPS Boston development board
+	  from Imagination Technologies in the FIT kernel image. You should
+	  enable this if you wish to boot on a MIPS Boston board, as it is
+	  expected by the bootloader.
+
+config FIT_IMAGE_FDT_MARDUK
+	bool "Include FDT for IMG Pistachio Marduk (CI40) boards"
+	help
+	  Enable this to include the FDT for the IMG Pistachio Marduk (CI40)
+	  from Imagination Technologies in the FIT kernel image.
+
+config FIT_IMAGE_FDT_NI169445
+	bool "Include FDT for NI 169445"
+	help
+	  Enable this to include the FDT for the 169445 platform from
+	  National Instruments in the FIT kernel image.
+
+config FIT_IMAGE_FDT_XILFPGA
+	bool "Include FDT for Xilfpga"
+	help
+	  Enable this to include the FDT for the MIPSfpga platform
+	  from Imagination Technologies in the FIT kernel image.
+
+config FIT_IMAGE_FDT_OCELOT
+	bool "Include FDT for Microsemi Ocelot development platforms"
+	select SOC_VCOREIII
+	help
+	  Enable this to include the FDT for the Ocelot development platforms
+	  from Microsemi in the FIT kernel image.
+	  This requires u-boot on the platform.
+
+config FIT_IMAGE_FDT_LUTON
+	bool "Include FDT for Microsemi Luton development platforms"
+	select SOC_VCOREIII
+	help
+	  Enable this to include the FDT for the Luton development platforms
+	  from Microsemi in the FIT kernel image.
+	  This requires u-boot on the platform.
+
+config FIT_IMAGE_FDT_JAGUAR2
+	bool "Include FDT for Microsemi Jaguar2 development platforms"
+	select SOC_VCOREIII
+	help
+	  Enable this to include the FDT for the Jaguar2 development platforms
+	  from Microsemi in the FIT kernel image.
+	  This requires u-boot on the platform.
+
+config FIT_IMAGE_FDT_SERVAL
+	bool "Include FDT for Microsemi Serval development platforms"
+	select SOC_VCOREIII
+	help
+	  Enable this to include the FDT for the Serval development platforms
+	  from Microsemi in the FIT kernel image.
+	  This requires u-boot on the platform.
+
+config BOARD_INGENIC
+	bool "Support boards based on Ingenic SoCs"
+	select MACH_INGENIC_GENERIC
+	help
+	  Enable support for boards based on Ingenic SoCs.
+
+config VIRT_BOARD_RANCHU
+	bool "Support Ranchu platform for Android emulator"
+	help
+	  This enables support for the platform used by Android emulator.
+
+	  Ranchu platform consists of a set of virtual devices. This platform
+	  enables emulation of variety of virtual configurations while using
+	  Android emulator. Android emulator is based on Qemu, and contains
+	  the support for the same set of virtual devices.
+
+endif
diff --git a/arch/mips/generic/Makefile b/arch/mips/generic/Makefile
new file mode 100644
index 000000000..e37a59bae
--- /dev/null
+++ b/arch/mips/generic/Makefile
@@ -0,0 +1,15 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+#
+# Copyright (C) 2016 Imagination Technologies
+# Author: Paul Burton <paul.burton@mips.com>
+#
+
+obj-y += init.o
+obj-y += irq.o
+obj-y += proc.o
+
+obj-$(CONFIG_YAMON_DT_SHIM)		+= yamon-dt.o
+obj-$(CONFIG_LEGACY_BOARD_SEAD3)	+= board-sead3.o
+obj-$(CONFIG_LEGACY_BOARD_OCELOT)	+= board-ocelot.o
+obj-$(CONFIG_MACH_INGENIC)			+= board-ingenic.o
+obj-$(CONFIG_VIRT_BOARD_RANCHU)		+= board-ranchu.o
diff --git a/arch/mips/generic/Platform b/arch/mips/generic/Platform
new file mode 100644
index 000000000..0c03623f3
--- /dev/null
+++ b/arch/mips/generic/Platform
@@ -0,0 +1,26 @@
+#
+# Copyright (C) 2016 Imagination Technologies
+# Author: Paul Burton <paul.burton@mips.com>
+#
+# This program is free software; you can redistribute it and/or modify it
+# under the terms of the GNU General Public License as published by the
+# Free Software Foundation;  either version 2 of the  License, or (at your
+# option) any later version.
+#
+
+# Note: order matters, keep the asm/mach-generic include last.
+cflags-$(CONFIG_MACH_INGENIC_SOC)	+= -I$(srctree)/arch/mips/include/asm/mach-ingenic
+cflags-$(CONFIG_MIPS_GENERIC)	+= -I$(srctree)/arch/mips/include/asm/mach-generic
+
+load-$(CONFIG_MIPS_GENERIC)	+= 0xffffffff80100000
+all-$(CONFIG_MIPS_GENERIC)	+= vmlinux.gz.itb
+
+its-y					:= vmlinux.its.S
+its-$(CONFIG_FIT_IMAGE_FDT_BOSTON)	+= board-boston.its.S
+its-$(CONFIG_FIT_IMAGE_FDT_NI169445)	+= board-ni169445.its.S
+its-$(CONFIG_FIT_IMAGE_FDT_OCELOT)	+= board-ocelot.its.S
+its-$(CONFIG_FIT_IMAGE_FDT_LUTON)	+= board-luton.its.S
+its-$(CONFIG_FIT_IMAGE_FDT_JAGUAR2)	+= board-jaguar2.its.S
+its-$(CONFIG_FIT_IMAGE_FDT_SERVAL)	+= board-serval.its.S
+its-$(CONFIG_FIT_IMAGE_FDT_XILFPGA)	+= board-xilfpga.its.S
+its-$(CONFIG_FIT_IMAGE_FDT_MARDUK)	+= board-marduk.its.S
diff --git a/arch/mips/generic/board-boston.its.S b/arch/mips/generic/board-boston.its.S
new file mode 100644
index 000000000..c45ad2759
--- /dev/null
+++ b/arch/mips/generic/board-boston.its.S
@@ -0,0 +1,22 @@
+/ {
+	images {
+		fdt-boston {
+			description = "img,boston Device Tree";
+			data = /incbin/("boot/dts/img/boston.dtb");
+			type = "flat_dt";
+			arch = "mips";
+			compression = "none";
+			hash {
+				algo = "sha1";
+			};
+		};
+	};
+
+	configurations {
+		conf-boston {
+			description = "Boston Linux kernel";
+			kernel = "kernel";
+			fdt = "fdt-boston";
+		};
+	};
+};
diff --git a/arch/mips/generic/board-ingenic.c b/arch/mips/generic/board-ingenic.c
new file mode 100644
index 000000000..c422bbc89
--- /dev/null
+++ b/arch/mips/generic/board-ingenic.c
@@ -0,0 +1,143 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Support for Ingenic SoCs
+ *
+ * Copyright (C) 2009-2010, Lars-Peter Clausen <lars@metafoo.de>
+ * Copyright (C) 2011, Maarten ter Huurne <maarten@treewalker.org>
+ * Copyright (C) 2020 Paul Cercueil <paul@crapouillou.net>
+ */
+
+#include <linux/clk.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_fdt.h>
+#include <linux/pm.h>
+#include <linux/sizes.h>
+#include <linux/suspend.h>
+#include <linux/types.h>
+
+#include <asm/bootinfo.h>
+#include <asm/machine.h>
+#include <asm/reboot.h>
+
+static __init char *ingenic_get_system_type(unsigned long machtype)
+{
+	switch (machtype) {
+	case MACH_INGENIC_X2100:
+		return "X2100";
+	case MACH_INGENIC_X2000H:
+		return "X2000H";
+	case MACH_INGENIC_X2000E:
+		return "X2000E";
+	case MACH_INGENIC_X2000:
+		return "X2000";
+	case MACH_INGENIC_X1830:
+		return "X1830";
+	case MACH_INGENIC_X1000E:
+		return "X1000E";
+	case MACH_INGENIC_X1000:
+		return "X1000";
+	case MACH_INGENIC_JZ4780:
+		return "JZ4780";
+	case MACH_INGENIC_JZ4775:
+		return "JZ4775";
+	case MACH_INGENIC_JZ4770:
+		return "JZ4770";
+	case MACH_INGENIC_JZ4760B:
+		return "JZ4760B";
+	case MACH_INGENIC_JZ4760:
+		return "JZ4760";
+	case MACH_INGENIC_JZ4755:
+		return "JZ4755";
+	case MACH_INGENIC_JZ4750:
+		return "JZ4750";
+	case MACH_INGENIC_JZ4725B:
+		return "JZ4725B";
+	case MACH_INGENIC_JZ4730:
+		return "JZ4730";
+	default:
+		return "JZ4740";
+	}
+}
+
+static __init const void *ingenic_fixup_fdt(const void *fdt, const void *match_data)
+{
+	/*
+	 * Old devicetree files for the qi,lb60 board did not have a /memory
+	 * node. Hardcode the memory info here.
+	 */
+	if (!fdt_node_check_compatible(fdt, 0, "qi,lb60") &&
+	    fdt_path_offset(fdt, "/memory") < 0)
+		early_init_dt_add_memory_arch(0, SZ_32M);
+
+	mips_machtype = (unsigned long)match_data;
+	system_type = ingenic_get_system_type(mips_machtype);
+
+	return fdt;
+}
+
+static const struct of_device_id ingenic_of_match[] __initconst = {
+	{ .compatible = "ingenic,jz4730", .data = (void *)MACH_INGENIC_JZ4730 },
+	{ .compatible = "ingenic,jz4740", .data = (void *)MACH_INGENIC_JZ4740 },
+	{ .compatible = "ingenic,jz4725b", .data = (void *)MACH_INGENIC_JZ4725B },
+	{ .compatible = "ingenic,jz4750", .data = (void *)MACH_INGENIC_JZ4750 },
+	{ .compatible = "ingenic,jz4755", .data = (void *)MACH_INGENIC_JZ4755 },
+	{ .compatible = "ingenic,jz4760", .data = (void *)MACH_INGENIC_JZ4760 },
+	{ .compatible = "ingenic,jz4760b", .data = (void *)MACH_INGENIC_JZ4760B },
+	{ .compatible = "ingenic,jz4770", .data = (void *)MACH_INGENIC_JZ4770 },
+	{ .compatible = "ingenic,jz4775", .data = (void *)MACH_INGENIC_JZ4775 },
+	{ .compatible = "ingenic,jz4780", .data = (void *)MACH_INGENIC_JZ4780 },
+	{ .compatible = "ingenic,x1000", .data = (void *)MACH_INGENIC_X1000 },
+	{ .compatible = "ingenic,x1000e", .data = (void *)MACH_INGENIC_X1000E },
+	{ .compatible = "ingenic,x1830", .data = (void *)MACH_INGENIC_X1830 },
+	{ .compatible = "ingenic,x2000", .data = (void *)MACH_INGENIC_X2000 },
+	{ .compatible = "ingenic,x2000e", .data = (void *)MACH_INGENIC_X2000E },
+	{ .compatible = "ingenic,x2000h", .data = (void *)MACH_INGENIC_X2000H },
+	{ .compatible = "ingenic,x2100", .data = (void *)MACH_INGENIC_X2100 },
+	{}
+};
+
+MIPS_MACHINE(ingenic) = {
+	.matches = ingenic_of_match,
+	.fixup_fdt = ingenic_fixup_fdt,
+};
+
+static void ingenic_wait_instr(void)
+{
+	__asm__(".set push;\n"
+		".set mips3;\n"
+		"wait;\n"
+		".set pop;\n"
+	);
+}
+
+static void ingenic_halt(void)
+{
+	for (;;)
+		ingenic_wait_instr();
+}
+
+static int __maybe_unused ingenic_pm_enter(suspend_state_t state)
+{
+	ingenic_wait_instr();
+
+	return 0;
+}
+
+static const struct platform_suspend_ops ingenic_pm_ops __maybe_unused = {
+	.valid = suspend_valid_only_mem,
+	.enter = ingenic_pm_enter,
+};
+
+static int __init ingenic_pm_init(void)
+{
+	if (boot_cpu_type() == CPU_XBURST) {
+		if (IS_ENABLED(CONFIG_PM_SLEEP))
+			suspend_set_ops(&ingenic_pm_ops);
+		_machine_halt = ingenic_halt;
+	}
+
+	return 0;
+
+}
+late_initcall(ingenic_pm_init);
diff --git a/arch/mips/generic/board-jaguar2.its.S b/arch/mips/generic/board-jaguar2.its.S
new file mode 100644
index 000000000..c2b8d479b
--- /dev/null
+++ b/arch/mips/generic/board-jaguar2.its.S
@@ -0,0 +1,40 @@
+/* SPDX-License-Identifier: (GPL-2.0 OR MIT) */
+/ {
+	images {
+		fdt-jaguar2_pcb110 {
+			description = "MSCC Jaguar2 PCB110 Device Tree";
+			data = /incbin/("boot/dts/mscc/jaguar2_pcb110.dtb");
+			type = "flat_dt";
+			arch = "mips";
+			compression = "none";
+			hash {
+				algo = "sha1";
+			};
+		};
+		fdt-jaguar2_pcb111 {
+			description = "MSCC Jaguar2 PCB111 Device Tree";
+			data = /incbin/("boot/dts/mscc/jaguar2_pcb111.dtb");
+			type = "flat_dt";
+			arch = "mips";
+			compression = "none";
+			hash {
+				algo = "sha1";
+			};
+		};
+	};
+
+	configurations {
+		pcb110 {
+			description = "Jaguar2 Linux kernel";
+			kernel = "kernel";
+			fdt = "fdt-jaguar2_pcb110";
+			ramdisk = "ramdisk";
+		};
+		pcb111 {
+			description = "Jaguar2 Linux kernel";
+			kernel = "kernel";
+			fdt = "fdt-jaguar2_pcb111";
+			ramdisk = "ramdisk";
+		};
+	};
+};
diff --git a/arch/mips/generic/board-luton.its.S b/arch/mips/generic/board-luton.its.S
new file mode 100644
index 000000000..bd9837c9a
--- /dev/null
+++ b/arch/mips/generic/board-luton.its.S
@@ -0,0 +1,23 @@
+/* SPDX-License-Identifier: (GPL-2.0 OR MIT) */
+/ {
+	images {
+		fdt-luton_pcb091 {
+			description = "MSCC Luton PCB091 Device Tree";
+			data = /incbin/("boot/dts/mscc/luton_pcb091.dtb");
+			type = "flat_dt";
+			arch = "mips";
+			compression = "none";
+			hash {
+				algo = "sha1";
+			};
+		};
+	};
+
+	configurations {
+		pcb091 {
+			description = "Luton Linux kernel";
+			kernel = "kernel";
+			fdt = "fdt-luton_pcb091";
+		};
+	};
+};
diff --git a/arch/mips/generic/board-marduk.its.S b/arch/mips/generic/board-marduk.its.S
new file mode 100644
index 000000000..4f633794d
--- /dev/null
+++ b/arch/mips/generic/board-marduk.its.S
@@ -0,0 +1,22 @@
+/ {
+	images {
+		fdt-marduk {
+			description = "img,pistachio-marduk Device Tree";
+			data = /incbin/("boot/dts/img/pistachio_marduk.dtb");
+			type = "flat_dt";
+			arch = "mips";
+			compression = "none";
+			hash {
+				algo = "sha1";
+			};
+		};
+	};
+
+	configurations {
+		conf-marduk {
+			description = "Marduk Linux kernel";
+			kernel = "kernel";
+			fdt = "fdt-marduk";
+		};
+	};
+};
diff --git a/arch/mips/generic/board-ni169445.its.S b/arch/mips/generic/board-ni169445.its.S
new file mode 100644
index 000000000..0a2e8f7a8
--- /dev/null
+++ b/arch/mips/generic/board-ni169445.its.S
@@ -0,0 +1,22 @@
+/ {
+	images {
+		fdt-ni169445 {
+			description = "NI 169445 device tree";
+			data = /incbin/("boot/dts/ni/169445.dtb");
+			type = "flat_dt";
+			arch = "mips";
+			compression = "none";
+			hash {
+				algo = "sha1";
+			};
+		};
+	};
+
+	configurations {
+		conf-ni169445 {
+			description = "NI 169445 Linux Kernel";
+			kernel = "kernel";
+			fdt = "fdt-ni169445";
+		};
+	};
+};
diff --git a/arch/mips/generic/board-ocelot.c b/arch/mips/generic/board-ocelot.c
new file mode 100644
index 000000000..7115410ac
--- /dev/null
+++ b/arch/mips/generic/board-ocelot.c
@@ -0,0 +1,78 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Microsemi MIPS SoC support
+ *
+ * Copyright (c) 2017 Microsemi Corporation
+ */
+#include <asm/machine.h>
+#include <asm/prom.h>
+
+#define DEVCPU_GCB_CHIP_REGS_CHIP_ID	0x71070000
+#define CHIP_ID_PART_ID			GENMASK(27, 12)
+
+#define OCELOT_PART_ID			(0x7514 << 12)
+
+#define UART_UART			0x70100000
+
+static __init bool ocelot_detect(void)
+{
+	u32 rev;
+	int idx;
+
+	/* Look for the TLB entry set up by redboot before trying to use it */
+	write_c0_entryhi(DEVCPU_GCB_CHIP_REGS_CHIP_ID);
+	mtc0_tlbw_hazard();
+	tlb_probe();
+	tlb_probe_hazard();
+	idx = read_c0_index();
+	if (idx < 0)
+		return false;
+
+	/* A TLB entry exists, lets assume its usable and check the CHIP ID */
+	rev = __raw_readl((void __iomem *)DEVCPU_GCB_CHIP_REGS_CHIP_ID);
+
+	if ((rev & CHIP_ID_PART_ID) != OCELOT_PART_ID)
+		return false;
+
+	/* Copy command line from bootloader early for Initrd detection */
+	if (fw_arg0 < 10 && (fw_arg1 & 0xFFF00000) == 0x80000000) {
+		unsigned int prom_argc = fw_arg0;
+		const char **prom_argv = (const char **)fw_arg1;
+
+		if (prom_argc > 1 && strlen(prom_argv[1]) > 0)
+			/* ignore all built-in args if any f/w args given */
+			strcpy(arcs_cmdline, prom_argv[1]);
+	}
+
+	return true;
+}
+
+static void __init ocelot_earlyprintk_init(void)
+{
+	void __iomem *uart_base;
+
+	uart_base = ioremap(UART_UART, 0x20);
+	setup_8250_early_printk_port((unsigned long)uart_base, 2, 50000);
+}
+
+static void __init ocelot_late_init(void)
+{
+	ocelot_earlyprintk_init();
+}
+
+static __init const void *ocelot_fixup_fdt(const void *fdt,
+					   const void *match_data)
+{
+	/* This has to be done so late because ioremap needs to work */
+	late_time_init = ocelot_late_init;
+
+	return fdt;
+}
+
+extern char __dtb_ocelot_pcb123_begin[];
+
+MIPS_MACHINE(ocelot) = {
+	.fdt = __dtb_ocelot_pcb123_begin,
+	.fixup_fdt = ocelot_fixup_fdt,
+	.detect = ocelot_detect,
+};
diff --git a/arch/mips/generic/board-ocelot.its.S b/arch/mips/generic/board-ocelot.its.S
new file mode 100644
index 000000000..8c7e3a1b6
--- /dev/null
+++ b/arch/mips/generic/board-ocelot.its.S
@@ -0,0 +1,40 @@
+/* SPDX-License-Identifier: (GPL-2.0 OR MIT) */
+/ {
+	images {
+		fdt-ocelot_pcb123 {
+			description = "MSCC Ocelot PCB123 Device Tree";
+			data = /incbin/("boot/dts/mscc/ocelot_pcb123.dtb");
+			type = "flat_dt";
+			arch = "mips";
+			compression = "none";
+			hash {
+				algo = "sha1";
+			};
+		};
+
+		fdt-ocelot_pcb120 {
+			description = "MSCC Ocelot PCB120 Device Tree";
+			data = /incbin/("boot/dts/mscc/ocelot_pcb120.dtb");
+			type = "flat_dt";
+			arch = "mips";
+			compression = "none";
+			hash {
+				algo = "sha1";
+			};
+		};
+	};
+
+	configurations {
+		conf-ocelot_pcb123 {
+			description = "Ocelot Linux kernel";
+			kernel = "kernel";
+			fdt = "fdt-ocelot_pcb123";
+		};
+
+		conf-ocelot_pcb120 {
+			description = "Ocelot Linux kernel";
+			kernel = "kernel";
+			fdt = "fdt-ocelot_pcb120";
+		};
+	};
+};
diff --git a/arch/mips/generic/board-ranchu.c b/arch/mips/generic/board-ranchu.c
new file mode 100644
index 000000000..930c45041
--- /dev/null
+++ b/arch/mips/generic/board-ranchu.c
@@ -0,0 +1,90 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Support code for virtual Ranchu board for MIPS.
+ *
+ * Author: Miodrag Dinic <miodrag.dinic@mips.com>
+ */
+
+#include <linux/of_address.h>
+#include <linux/types.h>
+
+#include <asm/machine.h>
+#include <asm/mipsregs.h>
+#include <asm/time.h>
+
+#define GOLDFISH_TIMER_LOW		0x00
+#define GOLDFISH_TIMER_HIGH		0x04
+
+static __init u64 read_rtc_time(void __iomem *base)
+{
+	u32 time_low;
+	u32 time_high;
+
+	/*
+	 * Reading the low address latches the high value
+	 * as well so there is no fear that we may read
+	 * inaccurate high value.
+	 */
+	time_low = readl(base + GOLDFISH_TIMER_LOW);
+	time_high = readl(base + GOLDFISH_TIMER_HIGH);
+
+	return ((u64)time_high << 32) | time_low;
+}
+
+static __init unsigned int ranchu_measure_hpt_freq(void)
+{
+	u64 rtc_start, rtc_current, rtc_delta;
+	unsigned int start, count;
+	struct device_node *np;
+	void __iomem *rtc_base;
+
+	np = of_find_compatible_node(NULL, NULL, "google,goldfish-rtc");
+	if (!np)
+		panic("%s(): Failed to find 'google,goldfish-rtc' dt node!",
+		      __func__);
+
+	rtc_base = of_iomap(np, 0);
+	of_node_put(np);
+	if (!rtc_base)
+		panic("%s(): Failed to ioremap Goldfish RTC base!", __func__);
+
+	/*
+	 * Poll the nanosecond resolution RTC for one
+	 * second to calibrate the CPU frequency.
+	 */
+	rtc_start = read_rtc_time(rtc_base);
+	start = read_c0_count();
+
+	do {
+		rtc_current = read_rtc_time(rtc_base);
+		rtc_delta = rtc_current - rtc_start;
+	} while (rtc_delta < NSEC_PER_SEC);
+
+	count = read_c0_count() - start;
+
+	/*
+	 * Make sure the frequency will be a round number.
+	 * Without this correction, the returned value may vary
+	 * between subsequent emulation executions.
+	 *
+	 * TODO: Set this value using device tree.
+	 */
+	count += 5000;
+	count -= count % 10000;
+
+	iounmap(rtc_base);
+
+	return count;
+}
+
+static const struct of_device_id ranchu_of_match[] __initconst = {
+	{
+		.compatible = "mti,ranchu",
+	},
+	{}
+};
+
+MIPS_MACHINE(ranchu) = {
+	.matches = ranchu_of_match,
+	.measure_hpt_freq = ranchu_measure_hpt_freq,
+};
diff --git a/arch/mips/generic/board-sead3.c b/arch/mips/generic/board-sead3.c
new file mode 100644
index 000000000..748ef4228
--- /dev/null
+++ b/arch/mips/generic/board-sead3.c
@@ -0,0 +1,220 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2016 Imagination Technologies
+ * Author: Paul Burton <paul.burton@mips.com>
+ */
+
+#define pr_fmt(fmt) "sead3: " fmt
+
+#include <linux/errno.h>
+#include <linux/libfdt.h>
+#include <linux/printk.h>
+#include <linux/sizes.h>
+
+#include <asm/fw/fw.h>
+#include <asm/io.h>
+#include <asm/machine.h>
+#include <asm/yamon-dt.h>
+
+#define SEAD_CONFIG			CKSEG1ADDR(0x1b100110)
+#define SEAD_CONFIG_GIC_PRESENT		BIT(1)
+
+#define MIPS_REVISION			CKSEG1ADDR(0x1fc00010)
+#define MIPS_REVISION_MACHINE		(0xf << 4)
+#define MIPS_REVISION_MACHINE_SEAD3	(0x4 << 4)
+
+/*
+ * Maximum 384MB RAM at physical address 0, preceding any I/O.
+ */
+static struct yamon_mem_region mem_regions[] __initdata = {
+	/* start	size */
+	{ 0,		SZ_256M + SZ_128M },
+	{}
+};
+
+static __init bool sead3_detect(void)
+{
+	uint32_t rev;
+
+	rev = __raw_readl((void *)MIPS_REVISION);
+	return (rev & MIPS_REVISION_MACHINE) == MIPS_REVISION_MACHINE_SEAD3;
+}
+
+static __init int append_memory(void *fdt)
+{
+	return yamon_dt_append_memory(fdt, mem_regions);
+}
+
+static __init int remove_gic(void *fdt)
+{
+	const unsigned int cpu_ehci_int = 2;
+	const unsigned int cpu_uart_int = 4;
+	const unsigned int cpu_eth_int = 6;
+	int gic_off, cpu_off, uart_off, eth_off, ehci_off, err;
+	uint32_t cfg, cpu_phandle;
+
+	/* leave the GIC node intact if a GIC is present */
+	cfg = __raw_readl((uint32_t *)SEAD_CONFIG);
+	if (cfg & SEAD_CONFIG_GIC_PRESENT)
+		return 0;
+
+	gic_off = fdt_node_offset_by_compatible(fdt, -1, "mti,gic");
+	if (gic_off < 0) {
+		pr_err("unable to find DT GIC node: %d\n", gic_off);
+		return gic_off;
+	}
+
+	err = fdt_nop_node(fdt, gic_off);
+	if (err) {
+		pr_err("unable to nop GIC node\n");
+		return err;
+	}
+
+	cpu_off = fdt_node_offset_by_compatible(fdt, -1,
+			"mti,cpu-interrupt-controller");
+	if (cpu_off < 0) {
+		pr_err("unable to find CPU intc node: %d\n", cpu_off);
+		return cpu_off;
+	}
+
+	cpu_phandle = fdt_get_phandle(fdt, cpu_off);
+	if (!cpu_phandle) {
+		pr_err("unable to get CPU intc phandle\n");
+		return -EINVAL;
+	}
+
+	uart_off = fdt_node_offset_by_compatible(fdt, -1, "ns16550a");
+	while (uart_off >= 0) {
+		err = fdt_setprop_u32(fdt, uart_off, "interrupt-parent",
+				      cpu_phandle);
+		if (err) {
+			pr_warn("unable to set UART interrupt-parent: %d\n",
+				err);
+			return err;
+		}
+
+		err = fdt_setprop_u32(fdt, uart_off, "interrupts",
+				      cpu_uart_int);
+		if (err) {
+			pr_err("unable to set UART interrupts property: %d\n",
+			       err);
+			return err;
+		}
+
+		uart_off = fdt_node_offset_by_compatible(fdt, uart_off,
+							 "ns16550a");
+	}
+	if (uart_off != -FDT_ERR_NOTFOUND) {
+		pr_err("error searching for UART DT node: %d\n", uart_off);
+		return uart_off;
+	}
+
+	eth_off = fdt_node_offset_by_compatible(fdt, -1, "smsc,lan9115");
+	if (eth_off < 0) {
+		pr_err("unable to find ethernet DT node: %d\n", eth_off);
+		return eth_off;
+	}
+
+	err = fdt_setprop_u32(fdt, eth_off, "interrupt-parent", cpu_phandle);
+	if (err) {
+		pr_err("unable to set ethernet interrupt-parent: %d\n", err);
+		return err;
+	}
+
+	err = fdt_setprop_u32(fdt, eth_off, "interrupts", cpu_eth_int);
+	if (err) {
+		pr_err("unable to set ethernet interrupts property: %d\n", err);
+		return err;
+	}
+
+	ehci_off = fdt_node_offset_by_compatible(fdt, -1, "generic-ehci");
+	if (ehci_off < 0) {
+		pr_err("unable to find EHCI DT node: %d\n", ehci_off);
+		return ehci_off;
+	}
+
+	err = fdt_setprop_u32(fdt, ehci_off, "interrupt-parent", cpu_phandle);
+	if (err) {
+		pr_err("unable to set EHCI interrupt-parent: %d\n", err);
+		return err;
+	}
+
+	err = fdt_setprop_u32(fdt, ehci_off, "interrupts", cpu_ehci_int);
+	if (err) {
+		pr_err("unable to set EHCI interrupts property: %d\n", err);
+		return err;
+	}
+
+	return 0;
+}
+
+static const struct mips_fdt_fixup sead3_fdt_fixups[] __initconst = {
+	{ yamon_dt_append_cmdline, "append command line" },
+	{ append_memory, "append memory" },
+	{ remove_gic, "remove GIC when not present" },
+	{ yamon_dt_serial_config, "append serial configuration" },
+	{ },
+};
+
+static __init const void *sead3_fixup_fdt(const void *fdt,
+					  const void *match_data)
+{
+	static unsigned char fdt_buf[16 << 10] __initdata;
+	int err;
+
+	if (fdt_check_header(fdt))
+		panic("Corrupt DT");
+
+	/* if this isn't SEAD3, something went wrong */
+	BUG_ON(fdt_node_check_compatible(fdt, 0, "mti,sead-3"));
+
+	fw_init_cmdline();
+
+	err = apply_mips_fdt_fixups(fdt_buf, sizeof(fdt_buf),
+				    fdt, sead3_fdt_fixups);
+	if (err)
+		panic("Unable to fixup FDT: %d", err);
+
+	return fdt_buf;
+}
+
+static __init unsigned int sead3_measure_hpt_freq(void)
+{
+	void __iomem *status_reg = (void __iomem *)0xbf000410;
+	unsigned int freq, orig, tick = 0;
+	unsigned long flags;
+
+	local_irq_save(flags);
+
+	orig = readl(status_reg) & 0x2;		      /* get original sample */
+	/* wait for transition */
+	while ((readl(status_reg) & 0x2) == orig)
+		;
+	orig = orig ^ 0x2;			      /* flip the bit */
+
+	write_c0_count(0);
+
+	/* wait 1 second (the sampling clock transitions every 10ms) */
+	while (tick < 100) {
+		/* wait for transition */
+		while ((readl(status_reg) & 0x2) == orig)
+			;
+		orig = orig ^ 0x2;			      /* flip the bit */
+		tick++;
+	}
+
+	freq = read_c0_count();
+
+	local_irq_restore(flags);
+
+	return freq;
+}
+
+extern char __dtb_sead3_begin[];
+
+MIPS_MACHINE(sead3) = {
+	.fdt = __dtb_sead3_begin,
+	.detect = sead3_detect,
+	.fixup_fdt = sead3_fixup_fdt,
+	.measure_hpt_freq = sead3_measure_hpt_freq,
+};
diff --git a/arch/mips/generic/board-serval.its.S b/arch/mips/generic/board-serval.its.S
new file mode 100644
index 000000000..dde833efe
--- /dev/null
+++ b/arch/mips/generic/board-serval.its.S
@@ -0,0 +1,24 @@
+/* SPDX-License-Identifier: (GPL-2.0 OR MIT) */
+/ {
+	images {
+		fdt-serval_pcb105 {
+			description = "MSCC Serval PCB105 Device Tree";
+			data = /incbin/("boot/dts/mscc/serval_pcb105.dtb");
+			type = "flat_dt";
+			arch = "mips";
+			compression = "none";
+			hash {
+				algo = "sha1";
+			};
+		};
+	};
+
+	configurations {
+		pcb105 {
+			description = "Serval Linux kernel";
+			kernel = "kernel";
+			fdt = "fdt-serval_pcb105";
+			ramdisk = "ramdisk";
+		};
+	};
+};
diff --git a/arch/mips/generic/board-xilfpga.its.S b/arch/mips/generic/board-xilfpga.its.S
new file mode 100644
index 000000000..08c1e900e
--- /dev/null
+++ b/arch/mips/generic/board-xilfpga.its.S
@@ -0,0 +1,22 @@
+/ {
+	images {
+		fdt-xilfpga {
+			description = "MIPSfpga (xilfpga) Device Tree";
+			data = /incbin/("boot/dts/xilfpga/nexys4ddr.dtb");
+			type = "flat_dt";
+			arch = "mips";
+			compression = "none";
+			hash {
+				algo = "sha1";
+			};
+		};
+	};
+
+	configurations {
+		conf-xilfpga {
+			description = "MIPSfpga Linux kernel";
+			kernel = "kernel";
+			fdt = "fdt-xilfpga";
+		};
+	};
+};
diff --git a/arch/mips/generic/init.c b/arch/mips/generic/init.c
new file mode 100644
index 000000000..1d712eac1
--- /dev/null
+++ b/arch/mips/generic/init.c
@@ -0,0 +1,204 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2016 Imagination Technologies
+ * Author: Paul Burton <paul.burton@mips.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/clocksource.h>
+#include <linux/init.h>
+#include <linux/irqchip.h>
+#include <linux/of_clk.h>
+#include <linux/of_fdt.h>
+
+#include <asm/bootinfo.h>
+#include <asm/fw/fw.h>
+#include <asm/irq_cpu.h>
+#include <asm/machine.h>
+#include <asm/mips-cps.h>
+#include <asm/prom.h>
+#include <asm/smp-ops.h>
+#include <asm/time.h>
+
+static __initconst const void *fdt;
+static __initconst const struct mips_machine *mach;
+static __initconst const void *mach_match_data;
+
+void __init prom_init(void)
+{
+	plat_get_fdt();
+	BUG_ON(!fdt);
+}
+
+void __init *plat_get_fdt(void)
+{
+	const struct mips_machine *check_mach;
+	const struct of_device_id *match;
+
+	if (fdt)
+		/* Already set up */
+		return (void *)fdt;
+
+	fdt = (void *)get_fdt();
+	if (fdt && !fdt_check_header(fdt)) {
+		/*
+		 * We have been provided with the appropriate device tree for
+		 * the board. Make use of it & search for any machine struct
+		 * based upon the root compatible string.
+		 */
+		for_each_mips_machine(check_mach) {
+			match = mips_machine_is_compatible(check_mach, fdt);
+			if (match) {
+				mach = check_mach;
+				mach_match_data = match->data;
+				break;
+			}
+		}
+	} else if (IS_ENABLED(CONFIG_LEGACY_BOARDS)) {
+		/*
+		 * We weren't booted using the UHI boot protocol, but do
+		 * support some number of boards with legacy boot protocols.
+		 * Attempt to find the right one.
+		 */
+		for_each_mips_machine(check_mach) {
+			if (!check_mach->detect)
+				continue;
+
+			if (!check_mach->detect())
+				continue;
+
+			mach = check_mach;
+		}
+
+		/*
+		 * If we don't recognise the machine then we can't continue, so
+		 * die here.
+		 */
+		BUG_ON(!mach);
+
+		/* Retrieve the machine's FDT */
+		fdt = mach->fdt;
+	}
+	return (void *)fdt;
+}
+
+#ifdef CONFIG_RELOCATABLE
+
+void __init plat_fdt_relocated(void *new_location)
+{
+	/*
+	 * reset fdt as the cached value would point to the location
+	 * before relocations happened and update the location argument
+	 * if it was passed using UHI
+	 */
+	fdt = NULL;
+
+	if (fw_arg0 == -2)
+		fw_arg1 = (unsigned long)new_location;
+}
+
+#endif /* CONFIG_RELOCATABLE */
+
+void __init plat_mem_setup(void)
+{
+	if (mach && mach->fixup_fdt)
+		fdt = mach->fixup_fdt(fdt, mach_match_data);
+
+	fw_init_cmdline();
+	__dt_setup_arch((void *)fdt);
+}
+
+void __init device_tree_init(void)
+{
+	unflatten_and_copy_device_tree();
+	mips_cpc_probe();
+
+	if (!register_cps_smp_ops())
+		return;
+	if (!register_vsmp_smp_ops())
+		return;
+
+	register_up_smp_ops();
+}
+
+int __init apply_mips_fdt_fixups(void *fdt_out, size_t fdt_out_size,
+				 const void *fdt_in,
+				 const struct mips_fdt_fixup *fixups)
+{
+	int err;
+
+	err = fdt_open_into(fdt_in, fdt_out, fdt_out_size);
+	if (err) {
+		pr_err("Failed to open FDT\n");
+		return err;
+	}
+
+	for (; fixups->apply; fixups++) {
+		err = fixups->apply(fdt_out);
+		if (err) {
+			pr_err("Failed to apply FDT fixup \"%s\"\n",
+			       fixups->description);
+			return err;
+		}
+	}
+
+	err = fdt_pack(fdt_out);
+	if (err)
+		pr_err("Failed to pack FDT\n");
+	return err;
+}
+
+void __init plat_time_init(void)
+{
+	struct device_node *np;
+	struct clk *clk;
+
+	of_clk_init(NULL);
+
+	if (!cpu_has_counter) {
+		mips_hpt_frequency = 0;
+	} else if (mach && mach->measure_hpt_freq) {
+		mips_hpt_frequency = mach->measure_hpt_freq();
+	} else {
+		np = of_get_cpu_node(0, NULL);
+		if (!np) {
+			pr_err("Failed to get CPU node\n");
+			return;
+		}
+
+		clk = of_clk_get(np, 0);
+		if (IS_ERR(clk)) {
+			pr_err("Failed to get CPU clock: %ld\n", PTR_ERR(clk));
+			return;
+		}
+
+		mips_hpt_frequency = clk_get_rate(clk);
+		clk_put(clk);
+
+		switch (boot_cpu_type()) {
+		case CPU_20KC:
+		case CPU_25KF:
+			/* The counter runs at the CPU clock rate */
+			break;
+		default:
+			/* The counter runs at half the CPU clock rate */
+			mips_hpt_frequency /= 2;
+			break;
+		}
+	}
+
+	timer_probe();
+}
+
+void __init arch_init_irq(void)
+{
+	struct device_node *intc_node;
+
+	intc_node = of_find_compatible_node(NULL, NULL,
+					    "mti,cpu-interrupt-controller");
+	if (!cpu_has_veic && !intc_node)
+		mips_cpu_irq_init();
+	of_node_put(intc_node);
+
+	irqchip_init();
+}
diff --git a/arch/mips/generic/irq.c b/arch/mips/generic/irq.c
new file mode 100644
index 000000000..933119262
--- /dev/null
+++ b/arch/mips/generic/irq.c
@@ -0,0 +1,61 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2016 Imagination Technologies
+ * Author: Paul Burton <paul.burton@mips.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/clocksource.h>
+#include <linux/init.h>
+#include <linux/types.h>
+
+#include <asm/irq.h>
+#include <asm/mips-cps.h>
+#include <asm/time.h>
+
+int get_c0_fdc_int(void)
+{
+	int mips_cpu_fdc_irq;
+
+	if (mips_gic_present())
+		mips_cpu_fdc_irq = gic_get_c0_fdc_int();
+	else if (cpu_has_veic)
+		panic("Unimplemented!");
+	else if (cp0_fdc_irq >= 0)
+		mips_cpu_fdc_irq = MIPS_CPU_IRQ_BASE + cp0_fdc_irq;
+	else
+		mips_cpu_fdc_irq = -1;
+
+	return mips_cpu_fdc_irq;
+}
+
+int get_c0_perfcount_int(void)
+{
+	int mips_cpu_perf_irq;
+
+	if (mips_gic_present())
+		mips_cpu_perf_irq = gic_get_c0_perfcount_int();
+	else if (cpu_has_veic)
+		panic("Unimplemented!");
+	else if (cp0_perfcount_irq >= 0)
+		mips_cpu_perf_irq = MIPS_CPU_IRQ_BASE + cp0_perfcount_irq;
+	else
+		mips_cpu_perf_irq = -1;
+
+	return mips_cpu_perf_irq;
+}
+
+unsigned int get_c0_compare_int(void)
+{
+	int mips_cpu_timer_irq;
+
+	if (mips_gic_present())
+		mips_cpu_timer_irq = gic_get_c0_compare_int();
+	else if (cpu_has_veic)
+		panic("Unimplemented!");
+	else
+		mips_cpu_timer_irq = MIPS_CPU_IRQ_BASE + cp0_compare_irq;
+
+	return mips_cpu_timer_irq;
+}
diff --git a/arch/mips/generic/proc.c b/arch/mips/generic/proc.c
new file mode 100644
index 000000000..cce2fde21
--- /dev/null
+++ b/arch/mips/generic/proc.c
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2016 Imagination Technologies
+ * Author: Paul Burton <paul.burton@mips.com>
+ */
+
+#include <linux/of.h>
+
+#include <asm/bootinfo.h>
+
+char *system_type;
+
+const char *get_system_type(void)
+{
+	const char *str;
+	int err;
+
+	if (system_type)
+		return system_type;
+
+	err = of_property_read_string(of_root, "model", &str);
+	if (!err)
+		return str;
+
+	err = of_property_read_string_index(of_root, "compatible", 0, &str);
+	if (!err)
+		return str;
+
+	return "Unknown";
+}
diff --git a/arch/mips/generic/vmlinux.its.S b/arch/mips/generic/vmlinux.its.S
new file mode 100644
index 000000000..3e2546765
--- /dev/null
+++ b/arch/mips/generic/vmlinux.its.S
@@ -0,0 +1,32 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/dts-v1/;
+
+/ {
+	description = KERNEL_NAME;
+	#address-cells = <ADDR_CELLS>;
+
+	images {
+		kernel {
+			description = KERNEL_NAME;
+			data = /incbin/(VMLINUX_BINARY);
+			type = "kernel";
+			arch = "mips";
+			os = "linux";
+			compression = VMLINUX_COMPRESSION;
+			load = /bits/ ADDR_BITS <VMLINUX_LOAD_ADDRESS>;
+			entry = /bits/ ADDR_BITS <VMLINUX_ENTRY_ADDRESS>;
+			hash {
+				algo = "sha1";
+			};
+		};
+	};
+
+	configurations {
+		default = "conf-default";
+
+		conf-default {
+			description = "Generic Linux kernel";
+			kernel = "kernel";
+		};
+	};
+};
diff --git a/arch/mips/generic/yamon-dt.c b/arch/mips/generic/yamon-dt.c
new file mode 100644
index 000000000..a07a5edbc
--- /dev/null
+++ b/arch/mips/generic/yamon-dt.c
@@ -0,0 +1,232 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2016 Imagination Technologies
+ * Author: Paul Burton <paul.burton@mips.com>
+ */
+
+#define pr_fmt(fmt) "yamon-dt: " fmt
+
+#include <linux/bug.h>
+#include <linux/errno.h>
+#include <linux/kernel.h>
+#include <linux/libfdt.h>
+#include <linux/printk.h>
+
+#include <asm/fw/fw.h>
+#include <asm/yamon-dt.h>
+
+#define MAX_MEM_ARRAY_ENTRIES	2
+
+__init int yamon_dt_append_cmdline(void *fdt)
+{
+	int err, chosen_off;
+
+	/* find or add chosen node */
+	chosen_off = fdt_path_offset(fdt, "/chosen");
+	if (chosen_off == -FDT_ERR_NOTFOUND)
+		chosen_off = fdt_add_subnode(fdt, 0, "chosen");
+	if (chosen_off < 0) {
+		pr_err("Unable to find or add DT chosen node: %d\n",
+		       chosen_off);
+		return chosen_off;
+	}
+
+	err = fdt_setprop_string(fdt, chosen_off, "bootargs", fw_getcmdline());
+	if (err) {
+		pr_err("Unable to set bootargs property: %d\n", err);
+		return err;
+	}
+
+	return 0;
+}
+
+static unsigned int __init gen_fdt_mem_array(
+					const struct yamon_mem_region *regions,
+					__be32 *mem_array,
+					unsigned int max_entries,
+					unsigned long memsize)
+{
+	const struct yamon_mem_region *mr;
+	unsigned long size;
+	unsigned int entries = 0;
+
+	for (mr = regions; mr->size && memsize; ++mr) {
+		if (entries >= max_entries) {
+			pr_warn("Number of regions exceeds max %u\n",
+				max_entries);
+			break;
+		}
+
+		/* How much of the remaining RAM fits in the next region? */
+		size = min_t(unsigned long, memsize, mr->size);
+		memsize -= size;
+
+		/* Emit a memory region */
+		*(mem_array++) = cpu_to_be32(mr->start);
+		*(mem_array++) = cpu_to_be32(size);
+		++entries;
+
+		/* Discard the next mr->discard bytes */
+		memsize -= min_t(unsigned long, memsize, mr->discard);
+	}
+	return entries;
+}
+
+__init int yamon_dt_append_memory(void *fdt,
+				  const struct yamon_mem_region *regions)
+{
+	unsigned long phys_memsize = 0, memsize;
+	__be32 mem_array[2 * MAX_MEM_ARRAY_ENTRIES];
+	unsigned int mem_entries;
+	int i, err, mem_off;
+	char *var, param_name[10], *var_names[] = {
+		"ememsize", "memsize",
+	};
+
+	/* find memory size from the bootloader environment */
+	for (i = 0; i < ARRAY_SIZE(var_names); i++) {
+		var = fw_getenv(var_names[i]);
+		if (!var)
+			continue;
+
+		err = kstrtoul(var, 0, &phys_memsize);
+		if (!err)
+			break;
+
+		pr_warn("Failed to read the '%s' env variable '%s'\n",
+			var_names[i], var);
+	}
+
+	if (!phys_memsize) {
+		pr_warn("The bootloader didn't provide memsize: defaulting to 32MB\n");
+		phys_memsize = 32 << 20;
+	}
+
+	/* default to using all available RAM */
+	memsize = phys_memsize;
+
+	/* allow the user to override the usable memory */
+	for (i = 0; i < ARRAY_SIZE(var_names); i++) {
+		snprintf(param_name, sizeof(param_name), "%s=", var_names[i]);
+		var = strstr(arcs_cmdline, param_name);
+		if (!var)
+			continue;
+
+		memsize = memparse(var + strlen(param_name), NULL);
+	}
+
+	/* if the user says there's more RAM than we thought, believe them */
+	phys_memsize = max_t(unsigned long, phys_memsize, memsize);
+
+	/* find or add a memory node */
+	mem_off = fdt_path_offset(fdt, "/memory");
+	if (mem_off == -FDT_ERR_NOTFOUND)
+		mem_off = fdt_add_subnode(fdt, 0, "memory");
+	if (mem_off < 0) {
+		pr_err("Unable to find or add memory DT node: %d\n", mem_off);
+		return mem_off;
+	}
+
+	err = fdt_setprop_string(fdt, mem_off, "device_type", "memory");
+	if (err) {
+		pr_err("Unable to set memory node device_type: %d\n", err);
+		return err;
+	}
+
+	mem_entries = gen_fdt_mem_array(regions, mem_array,
+					MAX_MEM_ARRAY_ENTRIES, phys_memsize);
+	err = fdt_setprop(fdt, mem_off, "reg",
+			  mem_array, mem_entries * 2 * sizeof(mem_array[0]));
+	if (err) {
+		pr_err("Unable to set memory regs property: %d\n", err);
+		return err;
+	}
+
+	mem_entries = gen_fdt_mem_array(regions, mem_array,
+					MAX_MEM_ARRAY_ENTRIES, memsize);
+	err = fdt_setprop(fdt, mem_off, "linux,usable-memory",
+			  mem_array, mem_entries * 2 * sizeof(mem_array[0]));
+	if (err) {
+		pr_err("Unable to set linux,usable-memory property: %d\n", err);
+		return err;
+	}
+
+	return 0;
+}
+
+__init int yamon_dt_serial_config(void *fdt)
+{
+	const char *yamontty, *mode_var;
+	char mode_var_name[9], path[20], parity;
+	unsigned int uart, baud, stop_bits;
+	bool hw_flow;
+	int chosen_off, err;
+
+	yamontty = fw_getenv("yamontty");
+	if (!yamontty || !strcmp(yamontty, "tty0")) {
+		uart = 0;
+	} else if (!strcmp(yamontty, "tty1")) {
+		uart = 1;
+	} else {
+		pr_warn("yamontty environment variable '%s' invalid\n",
+			yamontty);
+		uart = 0;
+	}
+
+	baud = stop_bits = 0;
+	parity = 0;
+	hw_flow = false;
+
+	snprintf(mode_var_name, sizeof(mode_var_name), "modetty%u", uart);
+	mode_var = fw_getenv(mode_var_name);
+	if (mode_var) {
+		while (mode_var[0] >= '0' && mode_var[0] <= '9') {
+			baud *= 10;
+			baud += mode_var[0] - '0';
+			mode_var++;
+		}
+		if (mode_var[0] == ',')
+			mode_var++;
+		if (mode_var[0])
+			parity = mode_var[0];
+		if (mode_var[0] == ',')
+			mode_var++;
+		if (mode_var[0])
+			stop_bits = mode_var[0] - '0';
+		if (mode_var[0] == ',')
+			mode_var++;
+		if (!strcmp(mode_var, "hw"))
+			hw_flow = true;
+	}
+
+	if (!baud)
+		baud = 38400;
+
+	if (parity != 'e' && parity != 'n' && parity != 'o')
+		parity = 'n';
+
+	if (stop_bits != 7 && stop_bits != 8)
+		stop_bits = 8;
+
+	WARN_ON(snprintf(path, sizeof(path), "serial%u:%u%c%u%s",
+			 uart, baud, parity, stop_bits,
+			 hw_flow ? "r" : "") >= sizeof(path));
+
+	/* find or add chosen node */
+	chosen_off = fdt_path_offset(fdt, "/chosen");
+	if (chosen_off == -FDT_ERR_NOTFOUND)
+		chosen_off = fdt_add_subnode(fdt, 0, "chosen");
+	if (chosen_off < 0) {
+		pr_err("Unable to find or add DT chosen node: %d\n",
+		       chosen_off);
+		return chosen_off;
+	}
+
+	err = fdt_setprop_string(fdt, chosen_off, "stdout-path", path);
+	if (err) {
+		pr_err("Unable to set stdout-path property: %d\n", err);
+		return err;
+	}
+
+	return 0;
+}
diff --git a/arch/mips/include/asm/Kbuild b/arch/mips/include/asm/Kbuild
new file mode 100644
index 000000000..dee172716
--- /dev/null
+++ b/arch/mips/include/asm/Kbuild
@@ -0,0 +1,16 @@
+# SPDX-License-Identifier: GPL-2.0
+# MIPS headers
+generated-y += syscall_table_n32.h
+generated-y += syscall_table_n64.h
+generated-y += syscall_table_o32.h
+generated-y += unistd_nr_n32.h
+generated-y += unistd_nr_n64.h
+generated-y += unistd_nr_o32.h
+
+generic-y += export.h
+generic-y += kvm_para.h
+generic-y += mcs_spinlock.h
+generic-y += parport.h
+generic-y += qrwlock.h
+generic-y += qspinlock.h
+generic-y += user.h
diff --git a/arch/mips/include/asm/abi.h b/arch/mips/include/asm/abi.h
new file mode 100644
index 000000000..dba7f4b6b
--- /dev/null
+++ b/arch/mips/include/asm/abi.h
@@ -0,0 +1,32 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2005, 06 by Ralf Baechle (ralf@linux-mips.org)
+ * Copyright (C) 2005 MIPS Technologies, Inc.
+ */
+#ifndef _ASM_ABI_H
+#define _ASM_ABI_H
+
+#include <linux/signal_types.h>
+
+#include <asm/signal.h>
+#include <asm/siginfo.h>
+#include <asm/vdso.h>
+
+struct mips_abi {
+	int (* const setup_frame)(void *sig_return, struct ksignal *ksig,
+				  struct pt_regs *regs, sigset_t *set);
+	int (* const setup_rt_frame)(void *sig_return, struct ksignal *ksig,
+				     struct pt_regs *regs, sigset_t *set);
+	const unsigned long	restart;
+
+	unsigned	off_sc_fpregs;
+	unsigned	off_sc_fpc_csr;
+	unsigned	off_sc_used_math;
+
+	struct mips_vdso_image *vdso;
+};
+
+#endif /* _ASM_ABI_H */
diff --git a/arch/mips/include/asm/addrspace.h b/arch/mips/include/asm/addrspace.h
new file mode 100644
index 000000000..59a48c60a
--- /dev/null
+++ b/arch/mips/include/asm/addrspace.h
@@ -0,0 +1,144 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1996, 99 Ralf Baechle
+ * Copyright (C) 2000, 2002  Maciej W. Rozycki
+ * Copyright (C) 1990, 1999 by Silicon Graphics, Inc.
+ */
+#ifndef _ASM_ADDRSPACE_H
+#define _ASM_ADDRSPACE_H
+
+#include <spaces.h>
+
+/*
+ *  Configure language
+ */
+#ifdef __ASSEMBLY__
+#define _ATYPE_
+#define _ATYPE32_
+#define _ATYPE64_
+#define _CONST64_(x)	x
+#else
+#define _ATYPE_		__PTRDIFF_TYPE__
+#define _ATYPE32_	int
+#define _ATYPE64_	__s64
+#ifdef CONFIG_64BIT
+#define _CONST64_(x)	x ## L
+#else
+#define _CONST64_(x)	x ## LL
+#endif
+#endif
+
+/*
+ *  32-bit MIPS address spaces
+ */
+#ifdef __ASSEMBLY__
+#define _ACAST32_
+#define _ACAST64_
+#else
+#define _ACAST32_		(_ATYPE_)(_ATYPE32_)	/* widen if necessary */
+#define _ACAST64_		(_ATYPE64_)		/* do _not_ narrow */
+#endif
+
+/*
+ * Returns the kernel segment base of a given address
+ */
+#define KSEGX(a)		((_ACAST32_(a)) & _ACAST32_(0xe0000000))
+
+/*
+ * Returns the physical address of a CKSEGx / XKPHYS address
+ */
+#define CPHYSADDR(a)		((_ACAST32_(a)) & 0x1fffffff)
+#define XPHYSADDR(a)		((_ACAST64_(a)) &			\
+				 _CONST64_(0x0000ffffffffffff))
+
+#ifdef CONFIG_64BIT
+
+/*
+ * Memory segments (64bit kernel mode addresses)
+ * The compatibility segments use the full 64-bit sign extended value.  Note
+ * the R8000 doesn't have them so don't reference these in generic MIPS code.
+ */
+#define XKUSEG			_CONST64_(0x0000000000000000)
+#define XKSSEG			_CONST64_(0x4000000000000000)
+#define XKPHYS			_CONST64_(0x8000000000000000)
+#define XKSEG			_CONST64_(0xc000000000000000)
+#define CKSEG0			_CONST64_(0xffffffff80000000)
+#define CKSEG1			_CONST64_(0xffffffffa0000000)
+#define CKSSEG			_CONST64_(0xffffffffc0000000)
+#define CKSEG3			_CONST64_(0xffffffffe0000000)
+
+#define CKSEG0ADDR(a)		(CPHYSADDR(a) | CKSEG0)
+#define CKSEG1ADDR(a)		(CPHYSADDR(a) | CKSEG1)
+#define CKSEG2ADDR(a)		(CPHYSADDR(a) | CKSEG2)
+#define CKSEG3ADDR(a)		(CPHYSADDR(a) | CKSEG3)
+
+#else
+
+#define CKSEG0ADDR(a)		(CPHYSADDR(a) | KSEG0)
+#define CKSEG1ADDR(a)		(CPHYSADDR(a) | KSEG1)
+#define CKSEG2ADDR(a)		(CPHYSADDR(a) | KSEG2)
+#define CKSEG3ADDR(a)		(CPHYSADDR(a) | KSEG3)
+
+/*
+ * Map an address to a certain kernel segment
+ */
+#define KSEG0ADDR(a)		(CPHYSADDR(a) | KSEG0)
+#define KSEG1ADDR(a)		(CPHYSADDR(a) | KSEG1)
+#define KSEG2ADDR(a)		(CPHYSADDR(a) | KSEG2)
+#define KSEG3ADDR(a)		(CPHYSADDR(a) | KSEG3)
+
+/*
+ * Memory segments (32bit kernel mode addresses)
+ * These are the traditional names used in the 32-bit universe.
+ */
+#define KUSEG			0x00000000
+#define KSEG0			0x80000000
+#define KSEG1			0xa0000000
+#define KSEG2			0xc0000000
+#define KSEG3			0xe0000000
+
+#define CKUSEG			0x00000000
+#define CKSEG0			0x80000000
+#define CKSEG1			0xa0000000
+#define CKSEG2			0xc0000000
+#define CKSEG3			0xe0000000
+
+#endif
+
+/*
+ * Cache modes for XKPHYS address conversion macros
+ */
+#define K_CALG_COH_EXCL1_NOL2	0
+#define K_CALG_COH_SHRL1_NOL2	1
+#define K_CALG_UNCACHED		2
+#define K_CALG_NONCOHERENT	3
+#define K_CALG_COH_EXCL		4
+#define K_CALG_COH_SHAREABLE	5
+#define K_CALG_NOTUSED		6
+#define K_CALG_UNCACHED_ACCEL	7
+
+/*
+ * 64-bit address conversions
+ */
+#define PHYS_TO_XKSEG_UNCACHED(p)	PHYS_TO_XKPHYS(K_CALG_UNCACHED, (p))
+#define PHYS_TO_XKSEG_CACHED(p)		PHYS_TO_XKPHYS(K_CALG_COH_SHAREABLE, (p))
+#define XKPHYS_TO_PHYS(p)		((p) & TO_PHYS_MASK)
+#define PHYS_TO_XKPHYS(cm, a)		(XKPHYS | (_ACAST64_(cm) << 59) | (a))
+
+/*
+ * The ultimate limited of the 64-bit MIPS architecture:  2 bits for selecting
+ * the region, 3 bits for the CCA mode.  This leaves 59 bits of which the
+ * R8000 implements most with its 48-bit physical address space.
+ */
+#define TO_PHYS_MASK	_CONST64_(0x07ffffffffffffff)	/* 2^^59 - 1 */
+
+#define COMPAT_K1BASE32		_CONST64_(0xffffffffa0000000)
+#define PHYS_TO_COMPATK1(x)	((x) | COMPAT_K1BASE32) /* 32-bit compat k1 */
+
+#define KDM_TO_PHYS(x)		(_ACAST64_ (x) & TO_PHYS_MASK)
+#define PHYS_TO_K0(x)		(_ACAST64_ (x) | CAC_BASE)
+
+#endif /* _ASM_ADDRSPACE_H */
diff --git a/arch/mips/include/asm/amon.h b/arch/mips/include/asm/amon.h
new file mode 100644
index 000000000..3cc03c64a
--- /dev/null
+++ b/arch/mips/include/asm/amon.h
@@ -0,0 +1,12 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2013 Imagination Technologies Ltd.
+ *
+ * Arbitrary Monitor Support (AMON)
+ */
+int amon_cpu_avail(int cpu);
+int amon_cpu_start(int cpu, unsigned long pc, unsigned long sp,
+		   unsigned long gp, unsigned long a0);
diff --git a/arch/mips/include/asm/arch_hweight.h b/arch/mips/include/asm/arch_hweight.h
new file mode 100644
index 000000000..712a7445e
--- /dev/null
+++ b/arch/mips/include/asm/arch_hweight.h
@@ -0,0 +1,38 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ */
+#ifndef _ASM_ARCH_HWEIGHT_H
+#define _ASM_ARCH_HWEIGHT_H
+
+#ifdef ARCH_HAS_USABLE_BUILTIN_POPCOUNT
+
+#include <asm/types.h>
+
+static inline unsigned int __arch_hweight32(unsigned int w)
+{
+	return __builtin_popcount(w);
+}
+
+static inline unsigned int __arch_hweight16(unsigned int w)
+{
+	return __builtin_popcount(w & 0xffff);
+}
+
+static inline unsigned int __arch_hweight8(unsigned int w)
+{
+	return __builtin_popcount(w & 0xff);
+}
+
+static inline unsigned long __arch_hweight64(__u64 w)
+{
+	return __builtin_popcountll(w);
+}
+
+#else
+#include <asm-generic/bitops/arch_hweight.h>
+#endif
+
+#endif /* _ASM_ARCH_HWEIGHT_H */
diff --git a/arch/mips/include/asm/asm-eva.h b/arch/mips/include/asm/asm-eva.h
new file mode 100644
index 000000000..e327ebc76
--- /dev/null
+++ b/arch/mips/include/asm/asm-eva.h
@@ -0,0 +1,190 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2014 Imagination Technologies Ltd.
+ *
+ */
+
+#ifndef __ASM_ASM_EVA_H
+#define __ASM_ASM_EVA_H
+
+#ifndef __ASSEMBLY__
+
+/* Kernel variants */
+
+#define kernel_cache(op, base)		"cache " op ", " base "\n"
+#define kernel_pref(hint, base)		"pref " hint ", " base "\n"
+#define kernel_ll(reg, addr)		"ll " reg ", " addr "\n"
+#define kernel_sc(reg, addr)		"sc " reg ", " addr "\n"
+#define kernel_lw(reg, addr)		"lw " reg ", " addr "\n"
+#define kernel_lwl(reg, addr)		"lwl " reg ", " addr "\n"
+#define kernel_lwr(reg, addr)		"lwr " reg ", " addr "\n"
+#define kernel_lh(reg, addr)		"lh " reg ", " addr "\n"
+#define kernel_lb(reg, addr)		"lb " reg ", " addr "\n"
+#define kernel_lbu(reg, addr)		"lbu " reg ", " addr "\n"
+#define kernel_sw(reg, addr)		"sw " reg ", " addr "\n"
+#define kernel_swl(reg, addr)		"swl " reg ", " addr "\n"
+#define kernel_swr(reg, addr)		"swr " reg ", " addr "\n"
+#define kernel_sh(reg, addr)		"sh " reg ", " addr "\n"
+#define kernel_sb(reg, addr)		"sb " reg ", " addr "\n"
+
+#ifdef CONFIG_32BIT
+/*
+ * No 'sd' or 'ld' instructions in 32-bit but the code will
+ * do the correct thing
+ */
+#define kernel_sd(reg, addr)		user_sw(reg, addr)
+#define kernel_ld(reg, addr)		user_lw(reg, addr)
+#else
+#define kernel_sd(reg, addr)		"sd " reg", " addr "\n"
+#define kernel_ld(reg, addr)		"ld " reg", " addr "\n"
+#endif /* CONFIG_32BIT */
+
+#ifdef CONFIG_EVA
+
+#define __BUILD_EVA_INSN(insn, reg, addr)				\
+				"	.set	push\n"			\
+				"	.set	mips0\n"		\
+				"	.set	eva\n"			\
+				"	"insn" "reg", "addr "\n"	\
+				"	.set	pop\n"
+
+#define user_cache(op, base)		__BUILD_EVA_INSN("cachee", op, base)
+#define user_pref(hint, base)		__BUILD_EVA_INSN("prefe", hint, base)
+#define user_ll(reg, addr)		__BUILD_EVA_INSN("lle", reg, addr)
+#define user_sc(reg, addr)		__BUILD_EVA_INSN("sce", reg, addr)
+#define user_lw(reg, addr)		__BUILD_EVA_INSN("lwe", reg, addr)
+#define user_lwl(reg, addr)		__BUILD_EVA_INSN("lwle", reg, addr)
+#define user_lwr(reg, addr)		__BUILD_EVA_INSN("lwre", reg, addr)
+#define user_lh(reg, addr)		__BUILD_EVA_INSN("lhe", reg, addr)
+#define user_lb(reg, addr)		__BUILD_EVA_INSN("lbe", reg, addr)
+#define user_lbu(reg, addr)		__BUILD_EVA_INSN("lbue", reg, addr)
+/* No 64-bit EVA instruction for loading double words */
+#define user_ld(reg, addr)		user_lw(reg, addr)
+#define user_sw(reg, addr)		__BUILD_EVA_INSN("swe", reg, addr)
+#define user_swl(reg, addr)		__BUILD_EVA_INSN("swle", reg, addr)
+#define user_swr(reg, addr)		__BUILD_EVA_INSN("swre", reg, addr)
+#define user_sh(reg, addr)		__BUILD_EVA_INSN("she", reg, addr)
+#define user_sb(reg, addr)		__BUILD_EVA_INSN("sbe", reg, addr)
+/* No 64-bit EVA instruction for storing double words */
+#define user_sd(reg, addr)		user_sw(reg, addr)
+
+#else
+
+#define user_cache(op, base)		kernel_cache(op, base)
+#define user_pref(hint, base)		kernel_pref(hint, base)
+#define user_ll(reg, addr)		kernel_ll(reg, addr)
+#define user_sc(reg, addr)		kernel_sc(reg, addr)
+#define user_lw(reg, addr)		kernel_lw(reg, addr)
+#define user_lwl(reg, addr)		kernel_lwl(reg, addr)
+#define user_lwr(reg, addr)		kernel_lwr(reg, addr)
+#define user_lh(reg, addr)		kernel_lh(reg, addr)
+#define user_lb(reg, addr)		kernel_lb(reg, addr)
+#define user_lbu(reg, addr)		kernel_lbu(reg, addr)
+#define user_sw(reg, addr)		kernel_sw(reg, addr)
+#define user_swl(reg, addr)		kernel_swl(reg, addr)
+#define user_swr(reg, addr)		kernel_swr(reg, addr)
+#define user_sh(reg, addr)		kernel_sh(reg, addr)
+#define user_sb(reg, addr)		kernel_sb(reg, addr)
+
+#ifdef CONFIG_32BIT
+#define user_sd(reg, addr)		kernel_sw(reg, addr)
+#define user_ld(reg, addr)		kernel_lw(reg, addr)
+#else
+#define user_sd(reg, addr)		kernel_sd(reg, addr)
+#define user_ld(reg, addr)		kernel_ld(reg, addr)
+#endif /* CONFIG_32BIT */
+
+#endif /* CONFIG_EVA */
+
+#else /* __ASSEMBLY__ */
+
+#define kernel_cache(op, base)		cache op, base
+#define kernel_pref(hint, base)		pref hint, base
+#define kernel_ll(reg, addr)		ll reg, addr
+#define kernel_sc(reg, addr)		sc reg, addr
+#define kernel_lw(reg, addr)		lw reg, addr
+#define kernel_lwl(reg, addr)		lwl reg, addr
+#define kernel_lwr(reg, addr)		lwr reg, addr
+#define kernel_lh(reg, addr)		lh reg, addr
+#define kernel_lb(reg, addr)		lb reg, addr
+#define kernel_lbu(reg, addr)		lbu reg, addr
+#define kernel_sw(reg, addr)		sw reg, addr
+#define kernel_swl(reg, addr)		swl reg, addr
+#define kernel_swr(reg, addr)		swr reg, addr
+#define kernel_sh(reg, addr)		sh reg, addr
+#define kernel_sb(reg, addr)		sb reg, addr
+
+#ifdef CONFIG_32BIT
+/*
+ * No 'sd' or 'ld' instructions in 32-bit but the code will
+ * do the correct thing
+ */
+#define kernel_sd(reg, addr)		user_sw(reg, addr)
+#define kernel_ld(reg, addr)		user_lw(reg, addr)
+#else
+#define kernel_sd(reg, addr)		sd reg, addr
+#define kernel_ld(reg, addr)		ld reg, addr
+#endif /* CONFIG_32BIT */
+
+#ifdef CONFIG_EVA
+
+#define __BUILD_EVA_INSN(insn, reg, addr)			\
+				.set	push;			\
+				.set	mips0;			\
+				.set	eva;			\
+				insn reg, addr;			\
+				.set	pop;
+
+#define user_cache(op, base)		__BUILD_EVA_INSN(cachee, op, base)
+#define user_pref(hint, base)		__BUILD_EVA_INSN(prefe, hint, base)
+#define user_ll(reg, addr)		__BUILD_EVA_INSN(lle, reg, addr)
+#define user_sc(reg, addr)		__BUILD_EVA_INSN(sce, reg, addr)
+#define user_lw(reg, addr)		__BUILD_EVA_INSN(lwe, reg, addr)
+#define user_lwl(reg, addr)		__BUILD_EVA_INSN(lwle, reg, addr)
+#define user_lwr(reg, addr)		__BUILD_EVA_INSN(lwre, reg, addr)
+#define user_lh(reg, addr)		__BUILD_EVA_INSN(lhe, reg, addr)
+#define user_lb(reg, addr)		__BUILD_EVA_INSN(lbe, reg, addr)
+#define user_lbu(reg, addr)		__BUILD_EVA_INSN(lbue, reg, addr)
+/* No 64-bit EVA instruction for loading double words */
+#define user_ld(reg, addr)		user_lw(reg, addr)
+#define user_sw(reg, addr)		__BUILD_EVA_INSN(swe, reg, addr)
+#define user_swl(reg, addr)		__BUILD_EVA_INSN(swle, reg, addr)
+#define user_swr(reg, addr)		__BUILD_EVA_INSN(swre, reg, addr)
+#define user_sh(reg, addr)		__BUILD_EVA_INSN(she, reg, addr)
+#define user_sb(reg, addr)		__BUILD_EVA_INSN(sbe, reg, addr)
+/* No 64-bit EVA instruction for loading double words */
+#define user_sd(reg, addr)		user_sw(reg, addr)
+#else
+
+#define user_cache(op, base)		kernel_cache(op, base)
+#define user_pref(hint, base)		kernel_pref(hint, base)
+#define user_ll(reg, addr)		kernel_ll(reg, addr)
+#define user_sc(reg, addr)		kernel_sc(reg, addr)
+#define user_lw(reg, addr)		kernel_lw(reg, addr)
+#define user_lwl(reg, addr)		kernel_lwl(reg, addr)
+#define user_lwr(reg, addr)		kernel_lwr(reg, addr)
+#define user_lh(reg, addr)		kernel_lh(reg, addr)
+#define user_lb(reg, addr)		kernel_lb(reg, addr)
+#define user_lbu(reg, addr)		kernel_lbu(reg, addr)
+#define user_sw(reg, addr)		kernel_sw(reg, addr)
+#define user_swl(reg, addr)		kernel_swl(reg, addr)
+#define user_swr(reg, addr)		kernel_swr(reg, addr)
+#define user_sh(reg, addr)		kernel_sh(reg, addr)
+#define user_sb(reg, addr)		kernel_sb(reg, addr)
+
+#ifdef CONFIG_32BIT
+#define user_sd(reg, addr)		kernel_sw(reg, addr)
+#define user_ld(reg, addr)		kernel_lw(reg, addr)
+#else
+#define user_sd(reg, addr)		kernel_sd(reg, addr)
+#define user_ld(reg, addr)		kernel_ld(reg, addr)
+#endif /* CONFIG_32BIT */
+
+#endif /* CONFIG_EVA */
+
+#endif /* __ASSEMBLY__ */
+
+#endif /* __ASM_ASM_EVA_H */
diff --git a/arch/mips/include/asm/asm-offsets.h b/arch/mips/include/asm/asm-offsets.h
new file mode 100644
index 000000000..d370ee36a
--- /dev/null
+++ b/arch/mips/include/asm/asm-offsets.h
@@ -0,0 +1 @@
+#include <generated/asm-offsets.h>
diff --git a/arch/mips/include/asm/asm-prototypes.h b/arch/mips/include/asm/asm-prototypes.h
new file mode 100644
index 000000000..f901ed043
--- /dev/null
+++ b/arch/mips/include/asm/asm-prototypes.h
@@ -0,0 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#include <asm/checksum.h>
+#include <asm/page.h>
+#include <asm/fpu.h>
+#include <asm-generic/asm-prototypes.h>
+#include <linux/uaccess.h>
+#include <asm/ftrace.h>
+#include <asm/mmu_context.h>
diff --git a/arch/mips/include/asm/asm.h b/arch/mips/include/asm/asm.h
new file mode 100644
index 000000000..336ac9b65
--- /dev/null
+++ b/arch/mips/include/asm/asm.h
@@ -0,0 +1,353 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995, 1996, 1997, 1999, 2001 by Ralf Baechle
+ * Copyright (C) 1999 by Silicon Graphics, Inc.
+ * Copyright (C) 2001 MIPS Technologies, Inc.
+ * Copyright (C) 2002  Maciej W. Rozycki
+ *
+ * Some useful macros for MIPS assembler code
+ *
+ * Some of the routines below contain useless nops that will be optimized
+ * away by gas in -O mode. These nops are however required to fill delay
+ * slots in noreorder mode.
+ */
+#ifndef __ASM_ASM_H
+#define __ASM_ASM_H
+
+#include <asm/sgidefs.h>
+#include <asm/asm-eva.h>
+#include <asm/isa-rev.h>
+
+#ifndef __VDSO__
+/*
+ * Emit CFI data in .debug_frame sections, not .eh_frame sections.
+ * We don't do DWARF unwinding at runtime, so only the offline DWARF
+ * information is useful to anyone. Note we should change this if we
+ * ever decide to enable DWARF unwinding at runtime.
+ */
+#define CFI_SECTIONS	.cfi_sections .debug_frame
+#else
+ /*
+  * For the vDSO, emit both runtime unwind information and debug
+  * symbols for the .dbg file.
+  */
+#define CFI_SECTIONS
+#endif
+
+/*
+ * LEAF - declare leaf routine
+ */
+#define LEAF(symbol)					\
+		CFI_SECTIONS;				\
+		.globl	symbol;				\
+		.align	2;				\
+		.type	symbol, @function;		\
+		.ent	symbol, 0;			\
+symbol:		.frame	sp, 0, ra;			\
+		.cfi_startproc;				\
+		.insn
+
+/*
+ * NESTED - declare nested routine entry point
+ */
+#define NESTED(symbol, framesize, rpc)			\
+		CFI_SECTIONS;				\
+		.globl	symbol;				\
+		.align	2;				\
+		.type	symbol, @function;		\
+		.ent	symbol, 0;			\
+symbol:		.frame	sp, framesize, rpc;		\
+		.cfi_startproc;				\
+		.insn
+
+/*
+ * END - mark end of function
+ */
+#define END(function)					\
+		.cfi_endproc;				\
+		.end	function;			\
+		.size	function, .-function
+
+/*
+ * EXPORT - export definition of symbol
+ */
+#define EXPORT(symbol)					\
+		.globl	symbol;				\
+symbol:
+
+/*
+ * FEXPORT - export definition of a function symbol
+ */
+#define FEXPORT(symbol)					\
+		.globl	symbol;				\
+		.type	symbol, @function;		\
+symbol:		.insn
+
+/*
+ * ABS - export absolute symbol
+ */
+#define ABS(symbol,value)				\
+		.globl	symbol;				\
+symbol		=	value
+
+#define TEXT(msg)					\
+		.pushsection .data;			\
+8:		.asciiz msg;				\
+		.popsection;
+
+#define ASM_PANIC(msg)					\
+		.set	push;				\
+		.set	reorder;			\
+		PTR_LA	a0, 8f;				\
+		jal	panic;				\
+9:		b	9b;				\
+		.set	pop;				\
+		TEXT(msg)
+
+/*
+ * Print formatted string
+ */
+#ifdef CONFIG_PRINTK
+#define ASM_PRINT(string)				\
+		.set	push;				\
+		.set	reorder;			\
+		PTR_LA	a0, 8f;				\
+		jal	_printk;			\
+		.set	pop;				\
+		TEXT(string)
+#else
+#define ASM_PRINT(string)
+#endif
+
+/*
+ * Stack alignment
+ */
+#if (_MIPS_SIM == _MIPS_SIM_ABI32)
+#define ALSZ	7
+#define ALMASK	~7
+#endif
+#if (_MIPS_SIM == _MIPS_SIM_NABI32) || (_MIPS_SIM == _MIPS_SIM_ABI64)
+#define ALSZ	15
+#define ALMASK	~15
+#endif
+
+/*
+ * Macros to handle different pointer/register sizes for 32/64-bit code
+ */
+
+/*
+ * Size of a register
+ */
+#ifdef __mips64
+#define SZREG	8
+#else
+#define SZREG	4
+#endif
+
+/*
+ * Use the following macros in assemblercode to load/store registers,
+ * pointers etc.
+ */
+#if (_MIPS_SIM == _MIPS_SIM_ABI32)
+#define REG_S		sw
+#define REG_L		lw
+#define REG_SUBU	subu
+#define REG_ADDU	addu
+#endif
+#if (_MIPS_SIM == _MIPS_SIM_NABI32) || (_MIPS_SIM == _MIPS_SIM_ABI64)
+#define REG_S		sd
+#define REG_L		ld
+#define REG_SUBU	dsubu
+#define REG_ADDU	daddu
+#endif
+
+/*
+ * How to add/sub/load/store/shift C int variables.
+ */
+#if (_MIPS_SZINT == 32)
+#define INT_ADD		add
+#define INT_ADDU	addu
+#define INT_ADDI	addi
+#define INT_ADDIU	addiu
+#define INT_SUB		sub
+#define INT_SUBU	subu
+#define INT_L		lw
+#define INT_S		sw
+#define INT_SLL		sll
+#define INT_SLLV	sllv
+#define INT_SRL		srl
+#define INT_SRLV	srlv
+#define INT_SRA		sra
+#define INT_SRAV	srav
+#endif
+
+#if (_MIPS_SZINT == 64)
+#define INT_ADD		dadd
+#define INT_ADDU	daddu
+#define INT_ADDI	daddi
+#define INT_ADDIU	daddiu
+#define INT_SUB		dsub
+#define INT_SUBU	dsubu
+#define INT_L		ld
+#define INT_S		sd
+#define INT_SLL		dsll
+#define INT_SLLV	dsllv
+#define INT_SRL		dsrl
+#define INT_SRLV	dsrlv
+#define INT_SRA		dsra
+#define INT_SRAV	dsrav
+#endif
+
+/*
+ * How to add/sub/load/store/shift C long variables.
+ */
+#if (_MIPS_SZLONG == 32)
+#define LONG_ADD	add
+#define LONG_ADDU	addu
+#define LONG_ADDI	addi
+#define LONG_ADDIU	addiu
+#define LONG_SUB	sub
+#define LONG_SUBU	subu
+#define LONG_L		lw
+#define LONG_LL		ll
+#define LONG_SC		sc
+#define LONG_S		sw
+#define LONG_SP		swp
+#define LONG_SLL	sll
+#define LONG_SLLV	sllv
+#define LONG_SRL	srl
+#define LONG_SRLV	srlv
+#define LONG_SRA	sra
+#define LONG_SRAV	srav
+#define LONG_INS	ins
+#define LONG_EXT	ext
+
+#ifdef __ASSEMBLY__
+#define LONG		.word
+#endif
+#define LONGSIZE	4
+#define LONGMASK	3
+#define LONGLOG		2
+#endif
+
+#if (_MIPS_SZLONG == 64)
+#define LONG_ADD	dadd
+#define LONG_ADDU	daddu
+#define LONG_ADDI	daddi
+#define LONG_ADDIU	daddiu
+#define LONG_SUB	dsub
+#define LONG_SUBU	dsubu
+#define LONG_L		ld
+#define LONG_LL		lld
+#define LONG_SC		scd
+#define LONG_S		sd
+#define LONG_SP		sdp
+#define LONG_SLL	dsll
+#define LONG_SLLV	dsllv
+#define LONG_SRL	dsrl
+#define LONG_SRLV	dsrlv
+#define LONG_SRA	dsra
+#define LONG_SRAV	dsrav
+#define LONG_INS	dins
+#define LONG_EXT	dext
+
+#ifdef __ASSEMBLY__
+#define LONG		.dword
+#endif
+#define LONGSIZE	8
+#define LONGMASK	7
+#define LONGLOG		3
+#endif
+
+/*
+ * How to add/sub/load/store/shift pointers.
+ */
+#if (_MIPS_SZPTR == 32)
+#define PTR_ADD		add
+#define PTR_ADDU	addu
+#define PTR_ADDI	addi
+#define PTR_ADDIU	addiu
+#define PTR_SUB		sub
+#define PTR_SUBU	subu
+#define PTR_L		lw
+#define PTR_S		sw
+#define PTR_LA		la
+#define PTR_LI		li
+#define PTR_SLL		sll
+#define PTR_SLLV	sllv
+#define PTR_SRL		srl
+#define PTR_SRLV	srlv
+#define PTR_SRA		sra
+#define PTR_SRAV	srav
+
+#define PTR_SCALESHIFT	2
+
+#define PTR_WD		.word
+#define PTRSIZE		4
+#define PTRLOG		2
+#endif
+
+#if (_MIPS_SZPTR == 64)
+#define PTR_ADD		dadd
+#define PTR_ADDU	daddu
+#define PTR_ADDI	daddi
+#define PTR_ADDIU	daddiu
+#define PTR_SUB		dsub
+#define PTR_SUBU	dsubu
+#define PTR_L		ld
+#define PTR_S		sd
+#define PTR_LA		dla
+#define PTR_LI		dli
+#define PTR_SLL		dsll
+#define PTR_SLLV	dsllv
+#define PTR_SRL		dsrl
+#define PTR_SRLV	dsrlv
+#define PTR_SRA		dsra
+#define PTR_SRAV	dsrav
+
+#define PTR_SCALESHIFT	3
+
+#define PTR_WD		.dword
+#define PTRSIZE		8
+#define PTRLOG		3
+#endif
+
+/*
+ * Some cp0 registers were extended to 64bit for MIPS III.
+ */
+#if (_MIPS_SIM == _MIPS_SIM_ABI32)
+#define MFC0		mfc0
+#define MTC0		mtc0
+#endif
+#if (_MIPS_SIM == _MIPS_SIM_NABI32) || (_MIPS_SIM == _MIPS_SIM_ABI64)
+#define MFC0		dmfc0
+#define MTC0		dmtc0
+#endif
+
+#define SSNOP		sll zero, zero, 1
+
+/*
+ * Using a branch-likely instruction to check the result of an sc instruction
+ * works around a bug present in R10000 CPUs prior to revision 3.0 that could
+ * cause ll-sc sequences to execute non-atomically.
+ */
+#ifdef CONFIG_WAR_R10000_LLSC
+# define SC_BEQZ	beqzl
+#elif MIPS_ISA_REV >= 6
+# define SC_BEQZ	beqzc
+#else
+# define SC_BEQZ	beqz
+#endif
+
+#ifdef CONFIG_SGI_IP28
+/* Inhibit speculative stores to volatile (e.g.DMA) or invalid addresses. */
+#include <asm/cacheops.h>
+#define R10KCBARRIER(addr)  cache   Cache_Barrier, addr;
+#else
+#define R10KCBARRIER(addr)
+#endif
+
+#endif /* __ASM_ASM_H */
diff --git a/arch/mips/include/asm/asmmacro-32.h b/arch/mips/include/asm/asmmacro-32.h
new file mode 100644
index 000000000..1c08c1f79
--- /dev/null
+++ b/arch/mips/include/asm/asmmacro-32.h
@@ -0,0 +1,91 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * asmmacro.h: Assembler macros to make things easier to read.
+ *
+ * Copyright (C) 1996 David S. Miller (davem@davemloft.net)
+ * Copyright (C) 1998, 1999, 2003 Ralf Baechle
+ */
+#ifndef _ASM_ASMMACRO_32_H
+#define _ASM_ASMMACRO_32_H
+
+#include <asm/asm-offsets.h>
+#include <asm/regdef.h>
+#include <asm/fpregdef.h>
+#include <asm/mipsregs.h>
+
+	.macro	fpu_save_single thread tmp=t0
+	.set push
+	SET_HARDFLOAT
+	cfc1	\tmp,  fcr31
+	s.d	$f0,  THREAD_FPR0(\thread)
+	s.d	$f2,  THREAD_FPR2(\thread)
+	s.d	$f4,  THREAD_FPR4(\thread)
+	s.d	$f6,  THREAD_FPR6(\thread)
+	s.d	$f8,  THREAD_FPR8(\thread)
+	s.d	$f10, THREAD_FPR10(\thread)
+	s.d	$f12, THREAD_FPR12(\thread)
+	s.d	$f14, THREAD_FPR14(\thread)
+	s.d	$f16, THREAD_FPR16(\thread)
+	s.d	$f18, THREAD_FPR18(\thread)
+	s.d	$f20, THREAD_FPR20(\thread)
+	s.d	$f22, THREAD_FPR22(\thread)
+	s.d	$f24, THREAD_FPR24(\thread)
+	s.d	$f26, THREAD_FPR26(\thread)
+	s.d	$f28, THREAD_FPR28(\thread)
+	s.d	$f30, THREAD_FPR30(\thread)
+	sw	\tmp, THREAD_FCR31(\thread)
+	.set pop
+	.endm
+
+	.macro	fpu_restore_single thread tmp=t0
+	.set push
+	SET_HARDFLOAT
+	lw	\tmp, THREAD_FCR31(\thread)
+	l.d	$f0,  THREAD_FPR0(\thread)
+	l.d	$f2,  THREAD_FPR2(\thread)
+	l.d	$f4,  THREAD_FPR4(\thread)
+	l.d	$f6,  THREAD_FPR6(\thread)
+	l.d	$f8,  THREAD_FPR8(\thread)
+	l.d	$f10, THREAD_FPR10(\thread)
+	l.d	$f12, THREAD_FPR12(\thread)
+	l.d	$f14, THREAD_FPR14(\thread)
+	l.d	$f16, THREAD_FPR16(\thread)
+	l.d	$f18, THREAD_FPR18(\thread)
+	l.d	$f20, THREAD_FPR20(\thread)
+	l.d	$f22, THREAD_FPR22(\thread)
+	l.d	$f24, THREAD_FPR24(\thread)
+	l.d	$f26, THREAD_FPR26(\thread)
+	l.d	$f28, THREAD_FPR28(\thread)
+	l.d	$f30, THREAD_FPR30(\thread)
+	ctc1	\tmp, fcr31
+	.set pop
+	.endm
+
+	.macro	cpu_save_nonscratch thread
+	LONG_S	s0, THREAD_REG16(\thread)
+	LONG_S	s1, THREAD_REG17(\thread)
+	LONG_S	s2, THREAD_REG18(\thread)
+	LONG_S	s3, THREAD_REG19(\thread)
+	LONG_S	s4, THREAD_REG20(\thread)
+	LONG_S	s5, THREAD_REG21(\thread)
+	LONG_S	s6, THREAD_REG22(\thread)
+	LONG_S	s7, THREAD_REG23(\thread)
+	LONG_S	sp, THREAD_REG29(\thread)
+	LONG_S	fp, THREAD_REG30(\thread)
+	.endm
+
+	.macro	cpu_restore_nonscratch thread
+	LONG_L	s0, THREAD_REG16(\thread)
+	LONG_L	s1, THREAD_REG17(\thread)
+	LONG_L	s2, THREAD_REG18(\thread)
+	LONG_L	s3, THREAD_REG19(\thread)
+	LONG_L	s4, THREAD_REG20(\thread)
+	LONG_L	s5, THREAD_REG21(\thread)
+	LONG_L	s6, THREAD_REG22(\thread)
+	LONG_L	s7, THREAD_REG23(\thread)
+	LONG_L	sp, THREAD_REG29(\thread)
+	LONG_L	fp, THREAD_REG30(\thread)
+	LONG_L	ra, THREAD_REG31(\thread)
+	.endm
+
+#endif /* _ASM_ASMMACRO_32_H */
diff --git a/arch/mips/include/asm/asmmacro-64.h b/arch/mips/include/asm/asmmacro-64.h
new file mode 100644
index 000000000..68039dee5
--- /dev/null
+++ b/arch/mips/include/asm/asmmacro-64.h
@@ -0,0 +1,44 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * asmmacro.h: Assembler macros to make things easier to read.
+ *
+ * Copyright (C) 1996 David S. Miller (davem@davemloft.net)
+ * Copyright (C) 1998, 1999 Ralf Baechle
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_ASMMACRO_64_H
+#define _ASM_ASMMACRO_64_H
+
+#include <asm/asm-offsets.h>
+#include <asm/regdef.h>
+#include <asm/fpregdef.h>
+#include <asm/mipsregs.h>
+
+	.macro	cpu_save_nonscratch thread
+	LONG_S	s0, THREAD_REG16(\thread)
+	LONG_S	s1, THREAD_REG17(\thread)
+	LONG_S	s2, THREAD_REG18(\thread)
+	LONG_S	s3, THREAD_REG19(\thread)
+	LONG_S	s4, THREAD_REG20(\thread)
+	LONG_S	s5, THREAD_REG21(\thread)
+	LONG_S	s6, THREAD_REG22(\thread)
+	LONG_S	s7, THREAD_REG23(\thread)
+	LONG_S	sp, THREAD_REG29(\thread)
+	LONG_S	fp, THREAD_REG30(\thread)
+	.endm
+
+	.macro	cpu_restore_nonscratch thread
+	LONG_L	s0, THREAD_REG16(\thread)
+	LONG_L	s1, THREAD_REG17(\thread)
+	LONG_L	s2, THREAD_REG18(\thread)
+	LONG_L	s3, THREAD_REG19(\thread)
+	LONG_L	s4, THREAD_REG20(\thread)
+	LONG_L	s5, THREAD_REG21(\thread)
+	LONG_L	s6, THREAD_REG22(\thread)
+	LONG_L	s7, THREAD_REG23(\thread)
+	LONG_L	sp, THREAD_REG29(\thread)
+	LONG_L	fp, THREAD_REG30(\thread)
+	LONG_L	ra, THREAD_REG31(\thread)
+	.endm
+
+#endif /* _ASM_ASMMACRO_64_H */
diff --git a/arch/mips/include/asm/asmmacro.h b/arch/mips/include/asm/asmmacro.h
new file mode 100644
index 000000000..ca83ada70
--- /dev/null
+++ b/arch/mips/include/asm/asmmacro.h
@@ -0,0 +1,658 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003 Ralf Baechle
+ */
+#ifndef _ASM_ASMMACRO_H
+#define _ASM_ASMMACRO_H
+
+#include <asm/hazards.h>
+#include <asm/asm-offsets.h>
+#include <asm/msa.h>
+
+#ifdef CONFIG_32BIT
+#include <asm/asmmacro-32.h>
+#endif
+#ifdef CONFIG_64BIT
+#include <asm/asmmacro-64.h>
+#endif
+
+/* preprocessor replaces the fp in ".set fp=64" with $30 otherwise */
+#undef fp
+
+/*
+ * Helper macros for generating raw instruction encodings.
+ */
+#ifdef CONFIG_CPU_MICROMIPS
+	.macro	insn32_if_mm enc
+	.insn
+	.hword ((\enc) >> 16)
+	.hword ((\enc) & 0xffff)
+	.endm
+
+	.macro	insn_if_mips enc
+	.endm
+#else
+	.macro	insn32_if_mm enc
+	.endm
+
+	.macro	insn_if_mips enc
+	.insn
+	.word (\enc)
+	.endm
+#endif
+
+#ifdef CONFIG_CPU_HAS_DIEI
+	.macro	local_irq_enable reg=t0
+	ei
+	irq_enable_hazard
+	.endm
+
+	.macro	local_irq_disable reg=t0
+	di
+	irq_disable_hazard
+	.endm
+#else /* !CONFIG_CPU_MIPSR2 && !CONFIG_CPU_MIPSR5 && !CONFIG_CPU_MIPSR6 */
+	.macro	local_irq_enable reg=t0
+	mfc0	\reg, CP0_STATUS
+	ori	\reg, \reg, 1
+	mtc0	\reg, CP0_STATUS
+	irq_enable_hazard
+	.endm
+
+	.macro	local_irq_disable reg=t0
+#ifdef CONFIG_PREEMPTION
+	lw      \reg, TI_PRE_COUNT($28)
+	addi    \reg, \reg, 1
+	sw      \reg, TI_PRE_COUNT($28)
+#endif
+	mfc0	\reg, CP0_STATUS
+	ori	\reg, \reg, 1
+	xori	\reg, \reg, 1
+	mtc0	\reg, CP0_STATUS
+	irq_disable_hazard
+#ifdef CONFIG_PREEMPTION
+	lw      \reg, TI_PRE_COUNT($28)
+	addi    \reg, \reg, -1
+	sw      \reg, TI_PRE_COUNT($28)
+#endif
+	.endm
+#endif  /* !CONFIG_CPU_MIPSR2 && !CONFIG_CPU_MIPSR5 && !CONFIG_CPU_MIPSR6 */
+
+	.macro	fpu_save_16even thread tmp=t0
+	.set	push
+	SET_HARDFLOAT
+	cfc1	\tmp, fcr31
+	sdc1	$f0,  THREAD_FPR0(\thread)
+	sdc1	$f2,  THREAD_FPR2(\thread)
+	sdc1	$f4,  THREAD_FPR4(\thread)
+	sdc1	$f6,  THREAD_FPR6(\thread)
+	sdc1	$f8,  THREAD_FPR8(\thread)
+	sdc1	$f10, THREAD_FPR10(\thread)
+	sdc1	$f12, THREAD_FPR12(\thread)
+	sdc1	$f14, THREAD_FPR14(\thread)
+	sdc1	$f16, THREAD_FPR16(\thread)
+	sdc1	$f18, THREAD_FPR18(\thread)
+	sdc1	$f20, THREAD_FPR20(\thread)
+	sdc1	$f22, THREAD_FPR22(\thread)
+	sdc1	$f24, THREAD_FPR24(\thread)
+	sdc1	$f26, THREAD_FPR26(\thread)
+	sdc1	$f28, THREAD_FPR28(\thread)
+	sdc1	$f30, THREAD_FPR30(\thread)
+	sw	\tmp, THREAD_FCR31(\thread)
+	.set	pop
+	.endm
+
+	.macro	fpu_save_16odd thread
+	.set	push
+	.set	mips64r2
+	.set	fp=64
+	SET_HARDFLOAT
+	sdc1	$f1,  THREAD_FPR1(\thread)
+	sdc1	$f3,  THREAD_FPR3(\thread)
+	sdc1	$f5,  THREAD_FPR5(\thread)
+	sdc1	$f7,  THREAD_FPR7(\thread)
+	sdc1	$f9,  THREAD_FPR9(\thread)
+	sdc1	$f11, THREAD_FPR11(\thread)
+	sdc1	$f13, THREAD_FPR13(\thread)
+	sdc1	$f15, THREAD_FPR15(\thread)
+	sdc1	$f17, THREAD_FPR17(\thread)
+	sdc1	$f19, THREAD_FPR19(\thread)
+	sdc1	$f21, THREAD_FPR21(\thread)
+	sdc1	$f23, THREAD_FPR23(\thread)
+	sdc1	$f25, THREAD_FPR25(\thread)
+	sdc1	$f27, THREAD_FPR27(\thread)
+	sdc1	$f29, THREAD_FPR29(\thread)
+	sdc1	$f31, THREAD_FPR31(\thread)
+	.set	pop
+	.endm
+
+	.macro	fpu_save_double thread status tmp
+#if defined(CONFIG_64BIT) || defined(CONFIG_CPU_MIPSR2) || \
+    defined(CONFIG_CPU_MIPSR5) || defined(CONFIG_CPU_MIPSR6)
+	sll	\tmp, \status, 5
+	bgez	\tmp, 10f
+	fpu_save_16odd \thread
+10:
+#endif
+	fpu_save_16even \thread \tmp
+	.endm
+
+	.macro	fpu_restore_16even thread tmp=t0
+	.set	push
+	SET_HARDFLOAT
+	lw	\tmp, THREAD_FCR31(\thread)
+	ldc1	$f0,  THREAD_FPR0(\thread)
+	ldc1	$f2,  THREAD_FPR2(\thread)
+	ldc1	$f4,  THREAD_FPR4(\thread)
+	ldc1	$f6,  THREAD_FPR6(\thread)
+	ldc1	$f8,  THREAD_FPR8(\thread)
+	ldc1	$f10, THREAD_FPR10(\thread)
+	ldc1	$f12, THREAD_FPR12(\thread)
+	ldc1	$f14, THREAD_FPR14(\thread)
+	ldc1	$f16, THREAD_FPR16(\thread)
+	ldc1	$f18, THREAD_FPR18(\thread)
+	ldc1	$f20, THREAD_FPR20(\thread)
+	ldc1	$f22, THREAD_FPR22(\thread)
+	ldc1	$f24, THREAD_FPR24(\thread)
+	ldc1	$f26, THREAD_FPR26(\thread)
+	ldc1	$f28, THREAD_FPR28(\thread)
+	ldc1	$f30, THREAD_FPR30(\thread)
+	ctc1	\tmp, fcr31
+	.set	pop
+	.endm
+
+	.macro	fpu_restore_16odd thread
+	.set	push
+	.set	mips64r2
+	.set	fp=64
+	SET_HARDFLOAT
+	ldc1	$f1,  THREAD_FPR1(\thread)
+	ldc1	$f3,  THREAD_FPR3(\thread)
+	ldc1	$f5,  THREAD_FPR5(\thread)
+	ldc1	$f7,  THREAD_FPR7(\thread)
+	ldc1	$f9,  THREAD_FPR9(\thread)
+	ldc1	$f11, THREAD_FPR11(\thread)
+	ldc1	$f13, THREAD_FPR13(\thread)
+	ldc1	$f15, THREAD_FPR15(\thread)
+	ldc1	$f17, THREAD_FPR17(\thread)
+	ldc1	$f19, THREAD_FPR19(\thread)
+	ldc1	$f21, THREAD_FPR21(\thread)
+	ldc1	$f23, THREAD_FPR23(\thread)
+	ldc1	$f25, THREAD_FPR25(\thread)
+	ldc1	$f27, THREAD_FPR27(\thread)
+	ldc1	$f29, THREAD_FPR29(\thread)
+	ldc1	$f31, THREAD_FPR31(\thread)
+	.set	pop
+	.endm
+
+	.macro	fpu_restore_double thread status tmp
+#if defined(CONFIG_64BIT) || defined(CONFIG_CPU_MIPSR2) || \
+    defined(CONFIG_CPU_MIPSR5) || defined(CONFIG_CPU_MIPSR6)
+	sll	\tmp, \status, 5
+	bgez	\tmp, 10f				# 16 register mode?
+
+	fpu_restore_16odd \thread
+10:
+#endif
+	fpu_restore_16even \thread \tmp
+	.endm
+
+#if defined(CONFIG_CPU_MIPSR2) || defined(CONFIG_CPU_MIPSR5) || \
+    defined(CONFIG_CPU_MIPSR6)
+	.macro	_EXT	rd, rs, p, s
+	ext	\rd, \rs, \p, \s
+	.endm
+#else /* !CONFIG_CPU_MIPSR2 && !CONFIG_CPU_MIPSR5 && !CONFIG_CPU_MIPSR6 */
+	.macro	_EXT	rd, rs, p, s
+	srl	\rd, \rs, \p
+	andi	\rd, \rd, (1 << \s) - 1
+	.endm
+#endif /* !CONFIG_CPU_MIPSR2 && !CONFIG_CPU_MIPSR5 && !CONFIG_CPU_MIPSR6 */
+
+/*
+ * Temporary until all gas have MT ASE support
+ */
+	.macro	DMT	reg=0
+	.word	0x41600bc1 | (\reg << 16)
+	.endm
+
+	.macro	EMT	reg=0
+	.word	0x41600be1 | (\reg << 16)
+	.endm
+
+	.macro	DVPE	reg=0
+	.word	0x41600001 | (\reg << 16)
+	.endm
+
+	.macro	EVPE	reg=0
+	.word	0x41600021 | (\reg << 16)
+	.endm
+
+	.macro	MFTR	rt=0, rd=0, u=0, sel=0
+	 .word	0x41000000 | (\rt << 16) | (\rd << 11) | (\u << 5) | (\sel)
+	.endm
+
+	.macro	MTTR	rt=0, rd=0, u=0, sel=0
+	 .word	0x41800000 | (\rt << 16) | (\rd << 11) | (\u << 5) | (\sel)
+	.endm
+
+#ifdef TOOLCHAIN_SUPPORTS_MSA
+	.macro	_cfcmsa	rd, cs
+	.set	push
+	.set	mips32r2
+	.set	fp=64
+	.set	msa
+	cfcmsa	\rd, $\cs
+	.set	pop
+	.endm
+
+	.macro	_ctcmsa	cd, rs
+	.set	push
+	.set	mips32r2
+	.set	fp=64
+	.set	msa
+	ctcmsa	$\cd, \rs
+	.set	pop
+	.endm
+
+	.macro	ld_b	wd, off, base
+	.set	push
+	.set	mips32r2
+	.set	fp=64
+	.set	msa
+	ld.b	$w\wd, \off(\base)
+	.set	pop
+	.endm
+
+	.macro	ld_h	wd, off, base
+	.set	push
+	.set	mips32r2
+	.set	fp=64
+	.set	msa
+	ld.h	$w\wd, \off(\base)
+	.set	pop
+	.endm
+
+	.macro	ld_w	wd, off, base
+	.set	push
+	.set	mips32r2
+	.set	fp=64
+	.set	msa
+	ld.w	$w\wd, \off(\base)
+	.set	pop
+	.endm
+
+	.macro	ld_d	wd, off, base
+	.set	push
+	.set	mips32r2
+	.set	fp=64
+	.set	msa
+	ld.d	$w\wd, \off(\base)
+	.set	pop
+	.endm
+
+	.macro	st_b	wd, off, base
+	.set	push
+	.set	mips32r2
+	.set	fp=64
+	.set	msa
+	st.b	$w\wd, \off(\base)
+	.set	pop
+	.endm
+
+	.macro	st_h	wd, off, base
+	.set	push
+	.set	mips32r2
+	.set	fp=64
+	.set	msa
+	st.h	$w\wd, \off(\base)
+	.set	pop
+	.endm
+
+	.macro	st_w	wd, off, base
+	.set	push
+	.set	mips32r2
+	.set	fp=64
+	.set	msa
+	st.w	$w\wd, \off(\base)
+	.set	pop
+	.endm
+
+	.macro	st_d	wd, off, base
+	.set	push
+	.set	mips32r2
+	.set	fp=64
+	.set	msa
+	st.d	$w\wd, \off(\base)
+	.set	pop
+	.endm
+
+	.macro	copy_s_w	ws, n
+	.set	push
+	.set	mips32r2
+	.set	fp=64
+	.set	msa
+	copy_s.w $1, $w\ws[\n]
+	.set	pop
+	.endm
+
+	.macro	copy_s_d	ws, n
+	.set	push
+	.set	mips64r2
+	.set	fp=64
+	.set	msa
+	copy_s.d $1, $w\ws[\n]
+	.set	pop
+	.endm
+
+	.macro	insert_w	wd, n
+	.set	push
+	.set	mips32r2
+	.set	fp=64
+	.set	msa
+	insert.w $w\wd[\n], $1
+	.set	pop
+	.endm
+
+	.macro	insert_d	wd, n
+	.set	push
+	.set	mips64r2
+	.set	fp=64
+	.set	msa
+	insert.d $w\wd[\n], $1
+	.set	pop
+	.endm
+#else
+
+	/*
+	 * Temporary until all toolchains in use include MSA support.
+	 */
+	.macro	_cfcmsa	rd, cs
+	.set	push
+	.set	noat
+	SET_HARDFLOAT
+	insn_if_mips 0x787e0059 | (\cs << 11)
+	insn32_if_mm 0x587e0056 | (\cs << 11)
+	move	\rd, $1
+	.set	pop
+	.endm
+
+	.macro	_ctcmsa	cd, rs
+	.set	push
+	.set	noat
+	SET_HARDFLOAT
+	move	$1, \rs
+	insn_if_mips 0x783e0819 | (\cd << 6)
+	insn32_if_mm 0x583e0816 | (\cd << 6)
+	.set	pop
+	.endm
+
+	.macro	ld_b	wd, off, base
+	.set	push
+	.set	noat
+	SET_HARDFLOAT
+	PTR_ADDU $1, \base, \off
+	insn_if_mips 0x78000820 | (\wd << 6)
+	insn32_if_mm 0x58000807 | (\wd << 6)
+	.set	pop
+	.endm
+
+	.macro	ld_h	wd, off, base
+	.set	push
+	.set	noat
+	SET_HARDFLOAT
+	PTR_ADDU $1, \base, \off
+	insn_if_mips 0x78000821 | (\wd << 6)
+	insn32_if_mm 0x58000817 | (\wd << 6)
+	.set	pop
+	.endm
+
+	.macro	ld_w	wd, off, base
+	.set	push
+	.set	noat
+	SET_HARDFLOAT
+	PTR_ADDU $1, \base, \off
+	insn_if_mips 0x78000822 | (\wd << 6)
+	insn32_if_mm 0x58000827 | (\wd << 6)
+	.set	pop
+	.endm
+
+	.macro	ld_d	wd, off, base
+	.set	push
+	.set	noat
+	SET_HARDFLOAT
+	PTR_ADDU $1, \base, \off
+	insn_if_mips 0x78000823 | (\wd << 6)
+	insn32_if_mm 0x58000837 | (\wd << 6)
+	.set	pop
+	.endm
+
+	.macro	st_b	wd, off, base
+	.set	push
+	.set	noat
+	SET_HARDFLOAT
+	PTR_ADDU $1, \base, \off
+	insn_if_mips 0x78000824 | (\wd << 6)
+	insn32_if_mm 0x5800080f | (\wd << 6)
+	.set	pop
+	.endm
+
+	.macro	st_h	wd, off, base
+	.set	push
+	.set	noat
+	SET_HARDFLOAT
+	PTR_ADDU $1, \base, \off
+	insn_if_mips 0x78000825 | (\wd << 6)
+	insn32_if_mm 0x5800081f | (\wd << 6)
+	.set	pop
+	.endm
+
+	.macro	st_w	wd, off, base
+	.set	push
+	.set	noat
+	SET_HARDFLOAT
+	PTR_ADDU $1, \base, \off
+	insn_if_mips 0x78000826 | (\wd << 6)
+	insn32_if_mm 0x5800082f | (\wd << 6)
+	.set	pop
+	.endm
+
+	.macro	st_d	wd, off, base
+	.set	push
+	.set	noat
+	SET_HARDFLOAT
+	PTR_ADDU $1, \base, \off
+	insn_if_mips 0x78000827 | (\wd << 6)
+	insn32_if_mm 0x5800083f | (\wd << 6)
+	.set	pop
+	.endm
+
+	.macro	copy_s_w	ws, n
+	.set	push
+	.set	noat
+	SET_HARDFLOAT
+	insn_if_mips 0x78b00059 | (\n << 16) | (\ws << 11)
+	insn32_if_mm 0x58b00056 | (\n << 16) | (\ws << 11)
+	.set	pop
+	.endm
+
+	.macro	copy_s_d	ws, n
+	.set	push
+	.set	noat
+	SET_HARDFLOAT
+	insn_if_mips 0x78b80059 | (\n << 16) | (\ws << 11)
+	insn32_if_mm 0x58b80056 | (\n << 16) | (\ws << 11)
+	.set	pop
+	.endm
+
+	.macro	insert_w	wd, n
+	.set	push
+	.set	noat
+	SET_HARDFLOAT
+	insn_if_mips 0x79300819 | (\n << 16) | (\wd << 6)
+	insn32_if_mm 0x59300816 | (\n << 16) | (\wd << 6)
+	.set	pop
+	.endm
+
+	.macro	insert_d	wd, n
+	.set	push
+	.set	noat
+	SET_HARDFLOAT
+	insn_if_mips 0x79380819 | (\n << 16) | (\wd << 6)
+	insn32_if_mm 0x59380816 | (\n << 16) | (\wd << 6)
+	.set	pop
+	.endm
+#endif
+
+#ifdef TOOLCHAIN_SUPPORTS_MSA
+#define FPR_BASE_OFFS	THREAD_FPR0
+#define FPR_BASE	$1
+#else
+#define FPR_BASE_OFFS	0
+#define FPR_BASE	\thread
+#endif
+
+	.macro	msa_save_all	thread
+	.set	push
+	.set	noat
+#ifdef TOOLCHAIN_SUPPORTS_MSA
+	PTR_ADDU FPR_BASE, \thread, FPR_BASE_OFFS
+#endif
+	st_d	 0, THREAD_FPR0  - FPR_BASE_OFFS, FPR_BASE
+	st_d	 1, THREAD_FPR1  - FPR_BASE_OFFS, FPR_BASE
+	st_d	 2, THREAD_FPR2  - FPR_BASE_OFFS, FPR_BASE
+	st_d	 3, THREAD_FPR3  - FPR_BASE_OFFS, FPR_BASE
+	st_d	 4, THREAD_FPR4  - FPR_BASE_OFFS, FPR_BASE
+	st_d	 5, THREAD_FPR5  - FPR_BASE_OFFS, FPR_BASE
+	st_d	 6, THREAD_FPR6  - FPR_BASE_OFFS, FPR_BASE
+	st_d	 7, THREAD_FPR7  - FPR_BASE_OFFS, FPR_BASE
+	st_d	 8, THREAD_FPR8  - FPR_BASE_OFFS, FPR_BASE
+	st_d	 9, THREAD_FPR9  - FPR_BASE_OFFS, FPR_BASE
+	st_d	10, THREAD_FPR10 - FPR_BASE_OFFS, FPR_BASE
+	st_d	11, THREAD_FPR11 - FPR_BASE_OFFS, FPR_BASE
+	st_d	12, THREAD_FPR12 - FPR_BASE_OFFS, FPR_BASE
+	st_d	13, THREAD_FPR13 - FPR_BASE_OFFS, FPR_BASE
+	st_d	14, THREAD_FPR14 - FPR_BASE_OFFS, FPR_BASE
+	st_d	15, THREAD_FPR15 - FPR_BASE_OFFS, FPR_BASE
+	st_d	16, THREAD_FPR16 - FPR_BASE_OFFS, FPR_BASE
+	st_d	17, THREAD_FPR17 - FPR_BASE_OFFS, FPR_BASE
+	st_d	18, THREAD_FPR18 - FPR_BASE_OFFS, FPR_BASE
+	st_d	19, THREAD_FPR19 - FPR_BASE_OFFS, FPR_BASE
+	st_d	20, THREAD_FPR20 - FPR_BASE_OFFS, FPR_BASE
+	st_d	21, THREAD_FPR21 - FPR_BASE_OFFS, FPR_BASE
+	st_d	22, THREAD_FPR22 - FPR_BASE_OFFS, FPR_BASE
+	st_d	23, THREAD_FPR23 - FPR_BASE_OFFS, FPR_BASE
+	st_d	24, THREAD_FPR24 - FPR_BASE_OFFS, FPR_BASE
+	st_d	25, THREAD_FPR25 - FPR_BASE_OFFS, FPR_BASE
+	st_d	26, THREAD_FPR26 - FPR_BASE_OFFS, FPR_BASE
+	st_d	27, THREAD_FPR27 - FPR_BASE_OFFS, FPR_BASE
+	st_d	28, THREAD_FPR28 - FPR_BASE_OFFS, FPR_BASE
+	st_d	29, THREAD_FPR29 - FPR_BASE_OFFS, FPR_BASE
+	st_d	30, THREAD_FPR30 - FPR_BASE_OFFS, FPR_BASE
+	st_d	31, THREAD_FPR31 - FPR_BASE_OFFS, FPR_BASE
+	SET_HARDFLOAT
+	_cfcmsa	$1, MSA_CSR
+	sw	$1, THREAD_MSA_CSR(\thread)
+	.set	pop
+	.endm
+
+	.macro	msa_restore_all	thread
+	.set	push
+	.set	noat
+	SET_HARDFLOAT
+	lw	$1, THREAD_MSA_CSR(\thread)
+	_ctcmsa	MSA_CSR, $1
+#ifdef TOOLCHAIN_SUPPORTS_MSA
+	PTR_ADDU FPR_BASE, \thread, FPR_BASE_OFFS
+#endif
+	ld_d	 0, THREAD_FPR0  - FPR_BASE_OFFS, FPR_BASE
+	ld_d	 1, THREAD_FPR1  - FPR_BASE_OFFS, FPR_BASE
+	ld_d	 2, THREAD_FPR2  - FPR_BASE_OFFS, FPR_BASE
+	ld_d	 3, THREAD_FPR3  - FPR_BASE_OFFS, FPR_BASE
+	ld_d	 4, THREAD_FPR4  - FPR_BASE_OFFS, FPR_BASE
+	ld_d	 5, THREAD_FPR5  - FPR_BASE_OFFS, FPR_BASE
+	ld_d	 6, THREAD_FPR6  - FPR_BASE_OFFS, FPR_BASE
+	ld_d	 7, THREAD_FPR7  - FPR_BASE_OFFS, FPR_BASE
+	ld_d	 8, THREAD_FPR8  - FPR_BASE_OFFS, FPR_BASE
+	ld_d	 9, THREAD_FPR9  - FPR_BASE_OFFS, FPR_BASE
+	ld_d	10, THREAD_FPR10 - FPR_BASE_OFFS, FPR_BASE
+	ld_d	11, THREAD_FPR11 - FPR_BASE_OFFS, FPR_BASE
+	ld_d	12, THREAD_FPR12 - FPR_BASE_OFFS, FPR_BASE
+	ld_d	13, THREAD_FPR13 - FPR_BASE_OFFS, FPR_BASE
+	ld_d	14, THREAD_FPR14 - FPR_BASE_OFFS, FPR_BASE
+	ld_d	15, THREAD_FPR15 - FPR_BASE_OFFS, FPR_BASE
+	ld_d	16, THREAD_FPR16 - FPR_BASE_OFFS, FPR_BASE
+	ld_d	17, THREAD_FPR17 - FPR_BASE_OFFS, FPR_BASE
+	ld_d	18, THREAD_FPR18 - FPR_BASE_OFFS, FPR_BASE
+	ld_d	19, THREAD_FPR19 - FPR_BASE_OFFS, FPR_BASE
+	ld_d	20, THREAD_FPR20 - FPR_BASE_OFFS, FPR_BASE
+	ld_d	21, THREAD_FPR21 - FPR_BASE_OFFS, FPR_BASE
+	ld_d	22, THREAD_FPR22 - FPR_BASE_OFFS, FPR_BASE
+	ld_d	23, THREAD_FPR23 - FPR_BASE_OFFS, FPR_BASE
+	ld_d	24, THREAD_FPR24 - FPR_BASE_OFFS, FPR_BASE
+	ld_d	25, THREAD_FPR25 - FPR_BASE_OFFS, FPR_BASE
+	ld_d	26, THREAD_FPR26 - FPR_BASE_OFFS, FPR_BASE
+	ld_d	27, THREAD_FPR27 - FPR_BASE_OFFS, FPR_BASE
+	ld_d	28, THREAD_FPR28 - FPR_BASE_OFFS, FPR_BASE
+	ld_d	29, THREAD_FPR29 - FPR_BASE_OFFS, FPR_BASE
+	ld_d	30, THREAD_FPR30 - FPR_BASE_OFFS, FPR_BASE
+	ld_d	31, THREAD_FPR31 - FPR_BASE_OFFS, FPR_BASE
+	.set pop
+	.endm
+
+#undef FPR_BASE_OFFS
+#undef FPR_BASE
+
+	.macro	msa_init_upper wd
+#ifdef CONFIG_64BIT
+	insert_d \wd, 1
+#else
+	insert_w \wd, 2
+	insert_w \wd, 3
+#endif
+	.endm
+
+	.macro	msa_init_all_upper
+	.set	push
+	.set	noat
+	SET_HARDFLOAT
+	not	$1, zero
+	msa_init_upper	0
+	msa_init_upper	1
+	msa_init_upper	2
+	msa_init_upper	3
+	msa_init_upper	4
+	msa_init_upper	5
+	msa_init_upper	6
+	msa_init_upper	7
+	msa_init_upper	8
+	msa_init_upper	9
+	msa_init_upper	10
+	msa_init_upper	11
+	msa_init_upper	12
+	msa_init_upper	13
+	msa_init_upper	14
+	msa_init_upper	15
+	msa_init_upper	16
+	msa_init_upper	17
+	msa_init_upper	18
+	msa_init_upper	19
+	msa_init_upper	20
+	msa_init_upper	21
+	msa_init_upper	22
+	msa_init_upper	23
+	msa_init_upper	24
+	msa_init_upper	25
+	msa_init_upper	26
+	msa_init_upper	27
+	msa_init_upper	28
+	msa_init_upper	29
+	msa_init_upper	30
+	msa_init_upper	31
+	.set	pop
+	.endm
+
+#endif /* _ASM_ASMMACRO_H */
diff --git a/arch/mips/include/asm/atomic.h b/arch/mips/include/asm/atomic.h
new file mode 100644
index 000000000..712fb5a6a
--- /dev/null
+++ b/arch/mips/include/asm/atomic.h
@@ -0,0 +1,269 @@
+/*
+ * Atomic operations that C can't guarantee us.  Useful for
+ * resource counting etc..
+ *
+ * But use these as seldom as possible since they are much more slower
+ * than regular operations.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1996, 97, 99, 2000, 03, 04, 06 by Ralf Baechle
+ */
+#ifndef _ASM_ATOMIC_H
+#define _ASM_ATOMIC_H
+
+#include <linux/irqflags.h>
+#include <linux/types.h>
+#include <asm/asm.h>
+#include <asm/barrier.h>
+#include <asm/compiler.h>
+#include <asm/cpu-features.h>
+#include <asm/cmpxchg.h>
+#include <asm/sync.h>
+
+#define ATOMIC_OPS(pfx, type)						\
+static __always_inline type arch_##pfx##_read(const pfx##_t *v)		\
+{									\
+	return READ_ONCE(v->counter);					\
+}									\
+									\
+static __always_inline void arch_##pfx##_set(pfx##_t *v, type i)	\
+{									\
+	WRITE_ONCE(v->counter, i);					\
+}									\
+									\
+static __always_inline type						\
+arch_##pfx##_cmpxchg(pfx##_t *v, type o, type n)			\
+{									\
+	return arch_cmpxchg(&v->counter, o, n);				\
+}									\
+									\
+static __always_inline type arch_##pfx##_xchg(pfx##_t *v, type n)	\
+{									\
+	return arch_xchg(&v->counter, n);				\
+}
+
+ATOMIC_OPS(atomic, int)
+
+#ifdef CONFIG_64BIT
+# define ATOMIC64_INIT(i)	{ (i) }
+ATOMIC_OPS(atomic64, s64)
+#endif
+
+#define ATOMIC_OP(pfx, op, type, c_op, asm_op, ll, sc)			\
+static __inline__ void arch_##pfx##_##op(type i, pfx##_t * v)		\
+{									\
+	type temp;							\
+									\
+	if (!kernel_uses_llsc) {					\
+		unsigned long flags;					\
+									\
+		raw_local_irq_save(flags);				\
+		v->counter c_op i;					\
+		raw_local_irq_restore(flags);				\
+		return;							\
+	}								\
+									\
+	__asm__ __volatile__(						\
+	"	.set	push					\n"	\
+	"	.set	" MIPS_ISA_LEVEL "			\n"	\
+	"	" __SYNC(full, loongson3_war) "			\n"	\
+	"1:	" #ll "	%0, %1		# " #pfx "_" #op "	\n"	\
+	"	" #asm_op " %0, %2				\n"	\
+	"	" #sc "	%0, %1					\n"	\
+	"\t" __stringify(SC_BEQZ) "	%0, 1b			\n"	\
+	"	.set	pop					\n"	\
+	: "=&r" (temp), "+" GCC_OFF_SMALL_ASM() (v->counter)		\
+	: "Ir" (i) : __LLSC_CLOBBER);					\
+}
+
+#define ATOMIC_OP_RETURN(pfx, op, type, c_op, asm_op, ll, sc)		\
+static __inline__ type							\
+arch_##pfx##_##op##_return_relaxed(type i, pfx##_t * v)			\
+{									\
+	type temp, result;						\
+									\
+	if (!kernel_uses_llsc) {					\
+		unsigned long flags;					\
+									\
+		raw_local_irq_save(flags);				\
+		result = v->counter;					\
+		result c_op i;						\
+		v->counter = result;					\
+		raw_local_irq_restore(flags);				\
+		return result;						\
+	}								\
+									\
+	__asm__ __volatile__(						\
+	"	.set	push					\n"	\
+	"	.set	" MIPS_ISA_LEVEL "			\n"	\
+	"	" __SYNC(full, loongson3_war) "			\n"	\
+	"1:	" #ll "	%1, %2		# " #pfx "_" #op "_return\n"	\
+	"	" #asm_op " %0, %1, %3				\n"	\
+	"	" #sc "	%0, %2					\n"	\
+	"\t" __stringify(SC_BEQZ) "	%0, 1b			\n"	\
+	"	" #asm_op " %0, %1, %3				\n"	\
+	"	.set	pop					\n"	\
+	: "=&r" (result), "=&r" (temp),					\
+	  "+" GCC_OFF_SMALL_ASM() (v->counter)				\
+	: "Ir" (i) : __LLSC_CLOBBER);					\
+									\
+	return result;							\
+}
+
+#define ATOMIC_FETCH_OP(pfx, op, type, c_op, asm_op, ll, sc)		\
+static __inline__ type							\
+arch_##pfx##_fetch_##op##_relaxed(type i, pfx##_t * v)			\
+{									\
+	int temp, result;						\
+									\
+	if (!kernel_uses_llsc) {					\
+		unsigned long flags;					\
+									\
+		raw_local_irq_save(flags);				\
+		result = v->counter;					\
+		v->counter c_op i;					\
+		raw_local_irq_restore(flags);				\
+		return result;						\
+	}								\
+									\
+	__asm__ __volatile__(						\
+	"	.set	push					\n"	\
+	"	.set	" MIPS_ISA_LEVEL "			\n"	\
+	"	" __SYNC(full, loongson3_war) "			\n"	\
+	"1:	" #ll "	%1, %2		# " #pfx "_fetch_" #op "\n"	\
+	"	" #asm_op " %0, %1, %3				\n"	\
+	"	" #sc "	%0, %2					\n"	\
+	"\t" __stringify(SC_BEQZ) "	%0, 1b			\n"	\
+	"	.set	pop					\n"	\
+	"	move	%0, %1					\n"	\
+	: "=&r" (result), "=&r" (temp),					\
+	  "+" GCC_OFF_SMALL_ASM() (v->counter)				\
+	: "Ir" (i) : __LLSC_CLOBBER);					\
+									\
+	return result;							\
+}
+
+#undef ATOMIC_OPS
+#define ATOMIC_OPS(pfx, op, type, c_op, asm_op, ll, sc)			\
+	ATOMIC_OP(pfx, op, type, c_op, asm_op, ll, sc)			\
+	ATOMIC_OP_RETURN(pfx, op, type, c_op, asm_op, ll, sc)		\
+	ATOMIC_FETCH_OP(pfx, op, type, c_op, asm_op, ll, sc)
+
+ATOMIC_OPS(atomic, add, int, +=, addu, ll, sc)
+ATOMIC_OPS(atomic, sub, int, -=, subu, ll, sc)
+
+#define arch_atomic_add_return_relaxed	arch_atomic_add_return_relaxed
+#define arch_atomic_sub_return_relaxed	arch_atomic_sub_return_relaxed
+#define arch_atomic_fetch_add_relaxed	arch_atomic_fetch_add_relaxed
+#define arch_atomic_fetch_sub_relaxed	arch_atomic_fetch_sub_relaxed
+
+#ifdef CONFIG_64BIT
+ATOMIC_OPS(atomic64, add, s64, +=, daddu, lld, scd)
+ATOMIC_OPS(atomic64, sub, s64, -=, dsubu, lld, scd)
+# define arch_atomic64_add_return_relaxed	arch_atomic64_add_return_relaxed
+# define arch_atomic64_sub_return_relaxed	arch_atomic64_sub_return_relaxed
+# define arch_atomic64_fetch_add_relaxed	arch_atomic64_fetch_add_relaxed
+# define arch_atomic64_fetch_sub_relaxed	arch_atomic64_fetch_sub_relaxed
+#endif /* CONFIG_64BIT */
+
+#undef ATOMIC_OPS
+#define ATOMIC_OPS(pfx, op, type, c_op, asm_op, ll, sc)			\
+	ATOMIC_OP(pfx, op, type, c_op, asm_op, ll, sc)			\
+	ATOMIC_FETCH_OP(pfx, op, type, c_op, asm_op, ll, sc)
+
+ATOMIC_OPS(atomic, and, int, &=, and, ll, sc)
+ATOMIC_OPS(atomic, or, int, |=, or, ll, sc)
+ATOMIC_OPS(atomic, xor, int, ^=, xor, ll, sc)
+
+#define arch_atomic_fetch_and_relaxed	arch_atomic_fetch_and_relaxed
+#define arch_atomic_fetch_or_relaxed	arch_atomic_fetch_or_relaxed
+#define arch_atomic_fetch_xor_relaxed	arch_atomic_fetch_xor_relaxed
+
+#ifdef CONFIG_64BIT
+ATOMIC_OPS(atomic64, and, s64, &=, and, lld, scd)
+ATOMIC_OPS(atomic64, or, s64, |=, or, lld, scd)
+ATOMIC_OPS(atomic64, xor, s64, ^=, xor, lld, scd)
+# define arch_atomic64_fetch_and_relaxed	arch_atomic64_fetch_and_relaxed
+# define arch_atomic64_fetch_or_relaxed		arch_atomic64_fetch_or_relaxed
+# define arch_atomic64_fetch_xor_relaxed	arch_atomic64_fetch_xor_relaxed
+#endif
+
+#undef ATOMIC_OPS
+#undef ATOMIC_FETCH_OP
+#undef ATOMIC_OP_RETURN
+#undef ATOMIC_OP
+
+/*
+ * atomic_sub_if_positive - conditionally subtract integer from atomic variable
+ * @i: integer value to subtract
+ * @v: pointer of type atomic_t
+ *
+ * Atomically test @v and subtract @i if @v is greater or equal than @i.
+ * The function returns the old value of @v minus @i.
+ */
+#define ATOMIC_SIP_OP(pfx, type, op, ll, sc)				\
+static __inline__ type arch_##pfx##_sub_if_positive(type i, pfx##_t * v)	\
+{									\
+	type temp, result;						\
+									\
+	smp_mb__before_atomic();					\
+									\
+	if (!kernel_uses_llsc) {					\
+		unsigned long flags;					\
+									\
+		raw_local_irq_save(flags);				\
+		result = v->counter;					\
+		result -= i;						\
+		if (result >= 0)					\
+			v->counter = result;				\
+		raw_local_irq_restore(flags);				\
+		smp_mb__after_atomic();					\
+		return result;						\
+	}								\
+									\
+	__asm__ __volatile__(						\
+	"	.set	push					\n"	\
+	"	.set	" MIPS_ISA_LEVEL "			\n"	\
+	"	" __SYNC(full, loongson3_war) "			\n"	\
+	"1:	" #ll "	%1, %2		# atomic_sub_if_positive\n"	\
+	"	.set	pop					\n"	\
+	"	" #op "	%0, %1, %3				\n"	\
+	"	move	%1, %0					\n"	\
+	"	bltz	%0, 2f					\n"	\
+	"	.set	push					\n"	\
+	"	.set	" MIPS_ISA_LEVEL "			\n"	\
+	"	" #sc "	%1, %2					\n"	\
+	"	" __stringify(SC_BEQZ) "	%1, 1b		\n"	\
+	"2:	" __SYNC(full, loongson3_war) "			\n"	\
+	"	.set	pop					\n"	\
+	: "=&r" (result), "=&r" (temp),					\
+	  "+" GCC_OFF_SMALL_ASM() (v->counter)				\
+	: "Ir" (i)							\
+	: __LLSC_CLOBBER);						\
+									\
+	/*								\
+	 * In the Loongson3 workaround case we already have a		\
+	 * completion barrier at 2: above, which is needed due to the	\
+	 * bltz that can branch	to code outside of the LL/SC loop. As	\
+	 * such, we don't need to emit another barrier here.		\
+	 */								\
+	if (__SYNC_loongson3_war == 0)					\
+		smp_mb__after_atomic();					\
+									\
+	return result;							\
+}
+
+ATOMIC_SIP_OP(atomic, int, subu, ll, sc)
+#define arch_atomic_dec_if_positive(v)	arch_atomic_sub_if_positive(1, v)
+
+#ifdef CONFIG_64BIT
+ATOMIC_SIP_OP(atomic64, s64, dsubu, lld, scd)
+#define arch_atomic64_dec_if_positive(v)	arch_atomic64_sub_if_positive(1, v)
+#endif
+
+#undef ATOMIC_SIP_OP
+
+#endif /* _ASM_ATOMIC_H */
diff --git a/arch/mips/include/asm/barrier.h b/arch/mips/include/asm/barrier.h
new file mode 100644
index 000000000..49ff172a7
--- /dev/null
+++ b/arch/mips/include/asm/barrier.h
@@ -0,0 +1,142 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2006 by Ralf Baechle (ralf@linux-mips.org)
+ */
+#ifndef __ASM_BARRIER_H
+#define __ASM_BARRIER_H
+
+#include <asm/addrspace.h>
+#include <asm/sync.h>
+
+static inline void __sync(void)
+{
+	asm volatile(__SYNC(full, always) ::: "memory");
+}
+
+static inline void rmb(void)
+{
+	asm volatile(__SYNC(rmb, always) ::: "memory");
+}
+#define rmb rmb
+
+static inline void wmb(void)
+{
+	asm volatile(__SYNC(wmb, always) ::: "memory");
+}
+#define wmb wmb
+
+#define fast_mb()	__sync()
+
+#define __fast_iob()				\
+	__asm__ __volatile__(			\
+		".set	push\n\t"		\
+		".set	noreorder\n\t"		\
+		"lw	$0,%0\n\t"		\
+		"nop\n\t"			\
+		".set	pop"			\
+		: /* no output */		\
+		: "m" (*(int *)CKSEG1)		\
+		: "memory")
+#ifdef CONFIG_CPU_CAVIUM_OCTEON
+# define fast_iob()	do { } while (0)
+#else /* ! CONFIG_CPU_CAVIUM_OCTEON */
+# ifdef CONFIG_SGI_IP28
+#  define fast_iob()				\
+	__asm__ __volatile__(			\
+		".set	push\n\t"		\
+		".set	noreorder\n\t"		\
+		"lw	$0,%0\n\t"		\
+		"sync\n\t"			\
+		"lw	$0,%0\n\t"		\
+		".set	pop"			\
+		: /* no output */		\
+		: "m" (*(int *)CKSEG1ADDR(0x1fa00004)) \
+		: "memory")
+# else
+#  define fast_iob()				\
+	do {					\
+		__sync();			\
+		__fast_iob();			\
+	} while (0)
+# endif
+#endif /* CONFIG_CPU_CAVIUM_OCTEON */
+
+#ifdef CONFIG_CPU_HAS_WB
+
+#include <asm/wbflush.h>
+
+#define mb()		wbflush()
+#define iob()		wbflush()
+
+#else /* !CONFIG_CPU_HAS_WB */
+
+#define mb()		fast_mb()
+#define iob()		fast_iob()
+
+#endif /* !CONFIG_CPU_HAS_WB */
+
+#if defined(CONFIG_WEAK_ORDERING)
+# define __smp_mb()	__sync()
+# define __smp_rmb()	rmb()
+# define __smp_wmb()	wmb()
+#else
+# define __smp_mb()	barrier()
+# define __smp_rmb()	barrier()
+# define __smp_wmb()	barrier()
+#endif
+
+/*
+ * When LL/SC does imply order, it must also be a compiler barrier to avoid the
+ * compiler from reordering where the CPU will not. When it does not imply
+ * order, the compiler is also free to reorder across the LL/SC loop and
+ * ordering will be done by smp_llsc_mb() and friends.
+ */
+#if defined(CONFIG_WEAK_REORDERING_BEYOND_LLSC) && defined(CONFIG_SMP)
+# define __WEAK_LLSC_MB		sync
+# define smp_llsc_mb() \
+	__asm__ __volatile__(__stringify(__WEAK_LLSC_MB) : : :"memory")
+# define __LLSC_CLOBBER
+#else
+# define __WEAK_LLSC_MB
+# define smp_llsc_mb()		do { } while (0)
+# define __LLSC_CLOBBER		"memory"
+#endif
+
+#ifdef CONFIG_CPU_CAVIUM_OCTEON
+#define smp_mb__before_llsc() smp_wmb()
+#define __smp_mb__before_llsc() __smp_wmb()
+/* Cause previous writes to become visible on all CPUs as soon as possible */
+#define nudge_writes() __asm__ __volatile__(".set push\n\t"		\
+					    ".set arch=octeon\n\t"	\
+					    "syncw\n\t"			\
+					    ".set pop" : : : "memory")
+#else
+#define smp_mb__before_llsc() smp_llsc_mb()
+#define __smp_mb__before_llsc() smp_llsc_mb()
+#define nudge_writes() mb()
+#endif
+
+/*
+ * In the Loongson3 LL/SC workaround case, all of our LL/SC loops already have
+ * a completion barrier immediately preceding the LL instruction. Therefore we
+ * can skip emitting a barrier from __smp_mb__before_atomic().
+ */
+#ifdef CONFIG_CPU_LOONGSON3_WORKAROUNDS
+# define __smp_mb__before_atomic()
+#else
+# define __smp_mb__before_atomic()	__smp_mb__before_llsc()
+#endif
+
+#define __smp_mb__after_atomic()	smp_llsc_mb()
+
+static inline void sync_ginv(void)
+{
+	asm volatile(__SYNC(ginv, always));
+}
+
+#include <asm-generic/barrier.h>
+
+#endif /* __ASM_BARRIER_H */
diff --git a/arch/mips/include/asm/bcache.h b/arch/mips/include/asm/bcache.h
new file mode 100644
index 000000000..a00857b13
--- /dev/null
+++ b/arch/mips/include/asm/bcache.h
@@ -0,0 +1,87 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (c) 1997, 1999 by Ralf Baechle
+ * Copyright (c) 1999 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_BCACHE_H
+#define _ASM_BCACHE_H
+
+#include <linux/types.h>
+
+/* Some R4000 / R4400 / R4600 / R5000 machines may have a non-dma-coherent,
+   chipset implemented caches.	On machines with other CPUs the CPU does the
+   cache thing itself. */
+struct bcache_ops {
+	void (*bc_enable)(void);
+	void (*bc_disable)(void);
+	void (*bc_wback_inv)(unsigned long page, unsigned long size);
+	void (*bc_inv)(unsigned long page, unsigned long size);
+	void (*bc_prefetch_enable)(void);
+	void (*bc_prefetch_disable)(void);
+	bool (*bc_prefetch_is_enabled)(void);
+};
+
+extern void indy_sc_init(void);
+
+#ifdef CONFIG_BOARD_SCACHE
+
+extern struct bcache_ops *bcops;
+
+static inline void bc_enable(void)
+{
+	bcops->bc_enable();
+}
+
+static inline void bc_disable(void)
+{
+	bcops->bc_disable();
+}
+
+static inline void bc_wback_inv(unsigned long page, unsigned long size)
+{
+	bcops->bc_wback_inv(page, size);
+}
+
+static inline void bc_inv(unsigned long page, unsigned long size)
+{
+	bcops->bc_inv(page, size);
+}
+
+static inline void bc_prefetch_enable(void)
+{
+	if (bcops->bc_prefetch_enable)
+		bcops->bc_prefetch_enable();
+}
+
+static inline void bc_prefetch_disable(void)
+{
+	if (bcops->bc_prefetch_disable)
+		bcops->bc_prefetch_disable();
+}
+
+static inline bool bc_prefetch_is_enabled(void)
+{
+	if (bcops->bc_prefetch_is_enabled)
+		return bcops->bc_prefetch_is_enabled();
+
+	return false;
+}
+
+#else /* !defined(CONFIG_BOARD_SCACHE) */
+
+/* Not R4000 / R4400 / R4600 / R5000.  */
+
+#define bc_enable() do { } while (0)
+#define bc_disable() do { } while (0)
+#define bc_wback_inv(page, size) do { } while (0)
+#define bc_inv(page, size) do { } while (0)
+#define bc_prefetch_enable() do { } while (0)
+#define bc_prefetch_disable() do { } while (0)
+#define bc_prefetch_is_enabled() 0
+
+#endif /* !defined(CONFIG_BOARD_SCACHE) */
+
+#endif /* _ASM_BCACHE_H */
diff --git a/arch/mips/include/asm/bitops.h b/arch/mips/include/asm/bitops.h
new file mode 100644
index 000000000..b4bf754f7
--- /dev/null
+++ b/arch/mips/include/asm/bitops.h
@@ -0,0 +1,460 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (c) 1994 - 1997, 99, 2000, 06, 07  Ralf Baechle (ralf@linux-mips.org)
+ * Copyright (c) 1999, 2000  Silicon Graphics, Inc.
+ */
+#ifndef _ASM_BITOPS_H
+#define _ASM_BITOPS_H
+
+#ifndef _LINUX_BITOPS_H
+#error only <linux/bitops.h> can be included directly
+#endif
+
+#include <linux/bits.h>
+#include <linux/compiler.h>
+#include <linux/types.h>
+#include <asm/asm.h>
+#include <asm/barrier.h>
+#include <asm/byteorder.h>		/* sigh ... */
+#include <asm/compiler.h>
+#include <asm/cpu-features.h>
+#include <asm/sgidefs.h>
+
+#define __bit_op(mem, insn, inputs...) do {			\
+	unsigned long __temp;					\
+								\
+	asm volatile(						\
+	"	.set		push			\n"	\
+	"	.set		" MIPS_ISA_LEVEL "	\n"	\
+	"	" __SYNC(full, loongson3_war) "		\n"	\
+	"1:	" __stringify(LONG_LL)	"	%0, %1	\n"	\
+	"	" insn		"			\n"	\
+	"	" __stringify(LONG_SC)	"	%0, %1	\n"	\
+	"	" __stringify(SC_BEQZ)	"	%0, 1b	\n"	\
+	"	.set		pop			\n"	\
+	: "=&r"(__temp), "+" GCC_OFF_SMALL_ASM()(mem)		\
+	: inputs						\
+	: __LLSC_CLOBBER);					\
+} while (0)
+
+#define __test_bit_op(mem, ll_dst, insn, inputs...) ({		\
+	unsigned long __orig, __temp;				\
+								\
+	asm volatile(						\
+	"	.set		push			\n"	\
+	"	.set		" MIPS_ISA_LEVEL "	\n"	\
+	"	" __SYNC(full, loongson3_war) "		\n"	\
+	"1:	" __stringify(LONG_LL) " "	ll_dst ", %2\n"	\
+	"	" insn		"			\n"	\
+	"	" __stringify(LONG_SC)	"	%1, %2	\n"	\
+	"	" __stringify(SC_BEQZ)	"	%1, 1b	\n"	\
+	"	.set		pop			\n"	\
+	: "=&r"(__orig), "=&r"(__temp),				\
+	  "+" GCC_OFF_SMALL_ASM()(mem)				\
+	: inputs						\
+	: __LLSC_CLOBBER);					\
+								\
+	__orig;							\
+})
+
+/*
+ * These are the "slower" versions of the functions and are in bitops.c.
+ * These functions call raw_local_irq_{save,restore}().
+ */
+void __mips_set_bit(unsigned long nr, volatile unsigned long *addr);
+void __mips_clear_bit(unsigned long nr, volatile unsigned long *addr);
+void __mips_change_bit(unsigned long nr, volatile unsigned long *addr);
+int __mips_test_and_set_bit_lock(unsigned long nr,
+				 volatile unsigned long *addr);
+int __mips_test_and_clear_bit(unsigned long nr,
+			      volatile unsigned long *addr);
+int __mips_test_and_change_bit(unsigned long nr,
+			       volatile unsigned long *addr);
+
+
+/*
+ * set_bit - Atomically set a bit in memory
+ * @nr: the bit to set
+ * @addr: the address to start counting from
+ *
+ * This function is atomic and may not be reordered.  See __set_bit()
+ * if you do not require the atomic guarantees.
+ * Note that @nr may be almost arbitrarily large; this function is not
+ * restricted to acting on a single-word quantity.
+ */
+static inline void set_bit(unsigned long nr, volatile unsigned long *addr)
+{
+	volatile unsigned long *m = &addr[BIT_WORD(nr)];
+	int bit = nr % BITS_PER_LONG;
+
+	if (!kernel_uses_llsc) {
+		__mips_set_bit(nr, addr);
+		return;
+	}
+
+	if ((MIPS_ISA_REV >= 2) && __builtin_constant_p(bit) && (bit >= 16)) {
+		__bit_op(*m, __stringify(LONG_INS) " %0, %3, %2, 1", "i"(bit), "r"(~0));
+		return;
+	}
+
+	__bit_op(*m, "or\t%0, %2", "ir"(BIT(bit)));
+}
+
+/*
+ * clear_bit - Clears a bit in memory
+ * @nr: Bit to clear
+ * @addr: Address to start counting from
+ *
+ * clear_bit() is atomic and may not be reordered.  However, it does
+ * not contain a memory barrier, so if it is used for locking purposes,
+ * you should call smp_mb__before_atomic() and/or smp_mb__after_atomic()
+ * in order to ensure changes are visible on other processors.
+ */
+static inline void clear_bit(unsigned long nr, volatile unsigned long *addr)
+{
+	volatile unsigned long *m = &addr[BIT_WORD(nr)];
+	int bit = nr % BITS_PER_LONG;
+
+	if (!kernel_uses_llsc) {
+		__mips_clear_bit(nr, addr);
+		return;
+	}
+
+	if ((MIPS_ISA_REV >= 2) && __builtin_constant_p(bit)) {
+		__bit_op(*m, __stringify(LONG_INS) " %0, $0, %2, 1", "i"(bit));
+		return;
+	}
+
+	__bit_op(*m, "and\t%0, %2", "ir"(~BIT(bit)));
+}
+
+/*
+ * clear_bit_unlock - Clears a bit in memory
+ * @nr: Bit to clear
+ * @addr: Address to start counting from
+ *
+ * clear_bit() is atomic and implies release semantics before the memory
+ * operation. It can be used for an unlock.
+ */
+static inline void clear_bit_unlock(unsigned long nr, volatile unsigned long *addr)
+{
+	smp_mb__before_atomic();
+	clear_bit(nr, addr);
+}
+
+/*
+ * change_bit - Toggle a bit in memory
+ * @nr: Bit to change
+ * @addr: Address to start counting from
+ *
+ * change_bit() is atomic and may not be reordered.
+ * Note that @nr may be almost arbitrarily large; this function is not
+ * restricted to acting on a single-word quantity.
+ */
+static inline void change_bit(unsigned long nr, volatile unsigned long *addr)
+{
+	volatile unsigned long *m = &addr[BIT_WORD(nr)];
+	int bit = nr % BITS_PER_LONG;
+
+	if (!kernel_uses_llsc) {
+		__mips_change_bit(nr, addr);
+		return;
+	}
+
+	__bit_op(*m, "xor\t%0, %2", "ir"(BIT(bit)));
+}
+
+/*
+ * test_and_set_bit_lock - Set a bit and return its old value
+ * @nr: Bit to set
+ * @addr: Address to count from
+ *
+ * This operation is atomic and implies acquire ordering semantics
+ * after the memory operation.
+ */
+static inline int test_and_set_bit_lock(unsigned long nr,
+	volatile unsigned long *addr)
+{
+	volatile unsigned long *m = &addr[BIT_WORD(nr)];
+	int bit = nr % BITS_PER_LONG;
+	unsigned long res, orig;
+
+	if (!kernel_uses_llsc) {
+		res = __mips_test_and_set_bit_lock(nr, addr);
+	} else {
+		orig = __test_bit_op(*m, "%0",
+				     "or\t%1, %0, %3",
+				     "ir"(BIT(bit)));
+		res = (orig & BIT(bit)) != 0;
+	}
+
+	smp_llsc_mb();
+
+	return res;
+}
+
+/*
+ * test_and_set_bit - Set a bit and return its old value
+ * @nr: Bit to set
+ * @addr: Address to count from
+ *
+ * This operation is atomic and cannot be reordered.
+ * It also implies a memory barrier.
+ */
+static inline int test_and_set_bit(unsigned long nr,
+	volatile unsigned long *addr)
+{
+	smp_mb__before_atomic();
+	return test_and_set_bit_lock(nr, addr);
+}
+
+/*
+ * test_and_clear_bit - Clear a bit and return its old value
+ * @nr: Bit to clear
+ * @addr: Address to count from
+ *
+ * This operation is atomic and cannot be reordered.
+ * It also implies a memory barrier.
+ */
+static inline int test_and_clear_bit(unsigned long nr,
+	volatile unsigned long *addr)
+{
+	volatile unsigned long *m = &addr[BIT_WORD(nr)];
+	int bit = nr % BITS_PER_LONG;
+	unsigned long res, orig;
+
+	smp_mb__before_atomic();
+
+	if (!kernel_uses_llsc) {
+		res = __mips_test_and_clear_bit(nr, addr);
+	} else if ((MIPS_ISA_REV >= 2) && __builtin_constant_p(nr)) {
+		res = __test_bit_op(*m, "%1",
+				    __stringify(LONG_EXT) " %0, %1, %3, 1;"
+				    __stringify(LONG_INS) " %1, $0, %3, 1",
+				    "i"(bit));
+	} else {
+		orig = __test_bit_op(*m, "%0",
+				     "or\t%1, %0, %3;"
+				     "xor\t%1, %1, %3",
+				     "ir"(BIT(bit)));
+		res = (orig & BIT(bit)) != 0;
+	}
+
+	smp_llsc_mb();
+
+	return res;
+}
+
+/*
+ * test_and_change_bit - Change a bit and return its old value
+ * @nr: Bit to change
+ * @addr: Address to count from
+ *
+ * This operation is atomic and cannot be reordered.
+ * It also implies a memory barrier.
+ */
+static inline int test_and_change_bit(unsigned long nr,
+	volatile unsigned long *addr)
+{
+	volatile unsigned long *m = &addr[BIT_WORD(nr)];
+	int bit = nr % BITS_PER_LONG;
+	unsigned long res, orig;
+
+	smp_mb__before_atomic();
+
+	if (!kernel_uses_llsc) {
+		res = __mips_test_and_change_bit(nr, addr);
+	} else {
+		orig = __test_bit_op(*m, "%0",
+				     "xor\t%1, %0, %3",
+				     "ir"(BIT(bit)));
+		res = (orig & BIT(bit)) != 0;
+	}
+
+	smp_llsc_mb();
+
+	return res;
+}
+
+#undef __bit_op
+#undef __test_bit_op
+
+#include <asm-generic/bitops/non-atomic.h>
+
+/*
+ * __clear_bit_unlock - Clears a bit in memory
+ * @nr: Bit to clear
+ * @addr: Address to start counting from
+ *
+ * __clear_bit() is non-atomic and implies release semantics before the memory
+ * operation. It can be used for an unlock if no other CPUs can concurrently
+ * modify other bits in the word.
+ */
+static inline void __clear_bit_unlock(unsigned long nr, volatile unsigned long *addr)
+{
+	smp_mb__before_llsc();
+	__clear_bit(nr, addr);
+	nudge_writes();
+}
+
+/*
+ * Return the bit position (0..63) of the most significant 1 bit in a word
+ * Returns -1 if no 1 bit exists
+ */
+static __always_inline unsigned long __fls(unsigned long word)
+{
+	int num;
+
+	if (BITS_PER_LONG == 32 && !__builtin_constant_p(word) &&
+	    __builtin_constant_p(cpu_has_clo_clz) && cpu_has_clo_clz) {
+		__asm__(
+		"	.set	push					\n"
+		"	.set	"MIPS_ISA_LEVEL"			\n"
+		"	clz	%0, %1					\n"
+		"	.set	pop					\n"
+		: "=r" (num)
+		: "r" (word));
+
+		return 31 - num;
+	}
+
+	if (BITS_PER_LONG == 64 && !__builtin_constant_p(word) &&
+	    __builtin_constant_p(cpu_has_mips64) && cpu_has_mips64) {
+		__asm__(
+		"	.set	push					\n"
+		"	.set	"MIPS_ISA_LEVEL"			\n"
+		"	dclz	%0, %1					\n"
+		"	.set	pop					\n"
+		: "=r" (num)
+		: "r" (word));
+
+		return 63 - num;
+	}
+
+	num = BITS_PER_LONG - 1;
+
+#if BITS_PER_LONG == 64
+	if (!(word & (~0ul << 32))) {
+		num -= 32;
+		word <<= 32;
+	}
+#endif
+	if (!(word & (~0ul << (BITS_PER_LONG-16)))) {
+		num -= 16;
+		word <<= 16;
+	}
+	if (!(word & (~0ul << (BITS_PER_LONG-8)))) {
+		num -= 8;
+		word <<= 8;
+	}
+	if (!(word & (~0ul << (BITS_PER_LONG-4)))) {
+		num -= 4;
+		word <<= 4;
+	}
+	if (!(word & (~0ul << (BITS_PER_LONG-2)))) {
+		num -= 2;
+		word <<= 2;
+	}
+	if (!(word & (~0ul << (BITS_PER_LONG-1))))
+		num -= 1;
+	return num;
+}
+
+/*
+ * __ffs - find first bit in word.
+ * @word: The word to search
+ *
+ * Returns 0..SZLONG-1
+ * Undefined if no bit exists, so code should check against 0 first.
+ */
+static __always_inline unsigned long __ffs(unsigned long word)
+{
+	return __fls(word & -word);
+}
+
+/*
+ * fls - find last bit set.
+ * @word: The word to search
+ *
+ * This is defined the same way as ffs.
+ * Note fls(0) = 0, fls(1) = 1, fls(0x80000000) = 32.
+ */
+static inline int fls(unsigned int x)
+{
+	int r;
+
+	if (!__builtin_constant_p(x) &&
+	    __builtin_constant_p(cpu_has_clo_clz) && cpu_has_clo_clz) {
+		__asm__(
+		"	.set	push					\n"
+		"	.set	"MIPS_ISA_LEVEL"			\n"
+		"	clz	%0, %1					\n"
+		"	.set	pop					\n"
+		: "=r" (x)
+		: "r" (x));
+
+		return 32 - x;
+	}
+
+	r = 32;
+	if (!x)
+		return 0;
+	if (!(x & 0xffff0000u)) {
+		x <<= 16;
+		r -= 16;
+	}
+	if (!(x & 0xff000000u)) {
+		x <<= 8;
+		r -= 8;
+	}
+	if (!(x & 0xf0000000u)) {
+		x <<= 4;
+		r -= 4;
+	}
+	if (!(x & 0xc0000000u)) {
+		x <<= 2;
+		r -= 2;
+	}
+	if (!(x & 0x80000000u)) {
+		x <<= 1;
+		r -= 1;
+	}
+	return r;
+}
+
+#include <asm-generic/bitops/fls64.h>
+
+/*
+ * ffs - find first bit set.
+ * @word: The word to search
+ *
+ * This is defined the same way as
+ * the libc and compiler builtin ffs routines, therefore
+ * differs in spirit from the below ffz (man ffs).
+ */
+static inline int ffs(int word)
+{
+	if (!word)
+		return 0;
+
+	return fls(word & -word);
+}
+
+#include <asm-generic/bitops/ffz.h>
+
+#ifdef __KERNEL__
+
+#include <asm-generic/bitops/sched.h>
+
+#include <asm/arch_hweight.h>
+#include <asm-generic/bitops/const_hweight.h>
+
+#include <asm-generic/bitops/le.h>
+#include <asm-generic/bitops/ext2-atomic.h>
+
+#endif /* __KERNEL__ */
+
+#endif /* _ASM_BITOPS_H */
diff --git a/arch/mips/include/asm/bitrev.h b/arch/mips/include/asm/bitrev.h
new file mode 100644
index 000000000..8a2538e08
--- /dev/null
+++ b/arch/mips/include/asm/bitrev.h
@@ -0,0 +1,31 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __MIPS_ASM_BITREV_H__
+#define __MIPS_ASM_BITREV_H__
+
+#include <linux/swab.h>
+
+static __always_inline __attribute_const__ u32 __arch_bitrev32(u32 x)
+{
+	u32 ret;
+
+	asm("bitswap	%0, %1" : "=r"(ret) : "r"(__swab32(x)));
+	return ret;
+}
+
+static __always_inline __attribute_const__ u16 __arch_bitrev16(u16 x)
+{
+	u16 ret;
+
+	asm("bitswap	%0, %1" : "=r"(ret) : "r"(__swab16(x)));
+	return ret;
+}
+
+static __always_inline __attribute_const__ u8 __arch_bitrev8(u8 x)
+{
+	u8 ret;
+
+	asm("bitswap	%0, %1" : "=r"(ret) : "r"(x));
+	return ret;
+}
+
+#endif /* __MIPS_ASM_BITREV_H__ */
diff --git a/arch/mips/include/asm/bmips-spaces.h b/arch/mips/include/asm/bmips-spaces.h
new file mode 100644
index 000000000..febc4c30a
--- /dev/null
+++ b/arch/mips/include/asm/bmips-spaces.h
@@ -0,0 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_BMIPS_SPACES_H
+#define __ASM_BMIPS_SPACES_H
+
+/* Avoid collisions with system base register (SBR) region on BMIPS3300 */
+#define FIXADDR_TOP		((unsigned long)(long)(int)0xff000000)
+
+#endif /* __ASM_BMIPS_SPACES_H */
diff --git a/arch/mips/include/asm/bmips.h b/arch/mips/include/asm/bmips.h
new file mode 100644
index 000000000..581a6a3c6
--- /dev/null
+++ b/arch/mips/include/asm/bmips.h
@@ -0,0 +1,128 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2011 by Kevin Cernekee (cernekee@gmail.com)
+ *
+ * Definitions for BMIPS processors
+ */
+#ifndef _ASM_BMIPS_H
+#define _ASM_BMIPS_H
+
+#include <linux/compiler.h>
+#include <linux/linkage.h>
+#include <asm/addrspace.h>
+#include <asm/mipsregs.h>
+#include <asm/hazards.h>
+
+/* NOTE: the CBR register returns a PA, and it can be above 0xff00_0000 */
+#define BMIPS_GET_CBR()			((void __iomem *)(CKSEG1 | \
+					 (unsigned long) \
+					 ((read_c0_brcm_cbr() >> 18) << 18)))
+
+#define BMIPS_RAC_CONFIG		0x00000000
+#define BMIPS_RAC_ADDRESS_RANGE		0x00000004
+#define BMIPS_RAC_CONFIG_1		0x00000008
+#define BMIPS_L2_CONFIG			0x0000000c
+#define BMIPS_LMB_CONTROL		0x0000001c
+#define BMIPS_SYSTEM_BASE		0x00000020
+#define BMIPS_PERF_GLOBAL_CONTROL	0x00020000
+#define BMIPS_PERF_CONTROL_0		0x00020004
+#define BMIPS_PERF_CONTROL_1		0x00020008
+#define BMIPS_PERF_COUNTER_0		0x00020010
+#define BMIPS_PERF_COUNTER_1		0x00020014
+#define BMIPS_PERF_COUNTER_2		0x00020018
+#define BMIPS_PERF_COUNTER_3		0x0002001c
+#define BMIPS_RELO_VECTOR_CONTROL_0	0x00030000
+#define BMIPS_RELO_VECTOR_CONTROL_1	0x00038000
+
+#define BMIPS_NMI_RESET_VEC		0x80000000
+#define BMIPS_WARM_RESTART_VEC		0x80000380
+
+#define ZSCM_REG_BASE			0x97000000
+
+#if !defined(__ASSEMBLY__)
+
+#include <linux/cpumask.h>
+#include <asm/r4kcache.h>
+#include <asm/smp-ops.h>
+
+extern const struct plat_smp_ops bmips43xx_smp_ops;
+extern const struct plat_smp_ops bmips5000_smp_ops;
+
+static inline int register_bmips_smp_ops(void)
+{
+#if IS_ENABLED(CONFIG_CPU_BMIPS) && IS_ENABLED(CONFIG_SMP)
+	switch (current_cpu_type()) {
+	case CPU_BMIPS32:
+	case CPU_BMIPS3300:
+		return register_up_smp_ops();
+	case CPU_BMIPS4350:
+	case CPU_BMIPS4380:
+		register_smp_ops(&bmips43xx_smp_ops);
+		break;
+	case CPU_BMIPS5000:
+		register_smp_ops(&bmips5000_smp_ops);
+		break;
+	default:
+		return -ENODEV;
+	}
+
+	return 0;
+#else
+	return -ENODEV;
+#endif
+}
+
+extern char bmips_reset_nmi_vec[];
+extern char bmips_reset_nmi_vec_end[];
+extern char bmips_smp_movevec[];
+extern char bmips_smp_int_vec[];
+extern char bmips_smp_int_vec_end[];
+
+extern int bmips_smp_enabled;
+extern int bmips_cpu_offset;
+extern cpumask_t bmips_booted_mask;
+extern unsigned long bmips_tp1_irqs;
+
+extern void bmips_ebase_setup(void);
+extern asmlinkage void plat_wired_tlb_setup(void);
+extern void bmips_cpu_setup(void);
+
+static inline unsigned long bmips_read_zscm_reg(unsigned int offset)
+{
+	unsigned long ret;
+
+	barrier();
+	cache_op(Index_Load_Tag_S, ZSCM_REG_BASE + offset);
+	__sync();
+	_ssnop();
+	_ssnop();
+	_ssnop();
+	_ssnop();
+	_ssnop();
+	_ssnop();
+	_ssnop();
+	ret = read_c0_ddatalo();
+	_ssnop();
+
+	return ret;
+}
+
+static inline void bmips_write_zscm_reg(unsigned int offset, unsigned long data)
+{
+	write_c0_ddatalo(data);
+	_ssnop();
+	_ssnop();
+	_ssnop();
+	cache_op(Index_Store_Tag_S, ZSCM_REG_BASE + offset);
+	_ssnop();
+	_ssnop();
+	_ssnop();
+	barrier();
+}
+
+#endif /* !defined(__ASSEMBLY__) */
+
+#endif /* _ASM_BMIPS_H */
diff --git a/arch/mips/include/asm/bootinfo.h b/arch/mips/include/asm/bootinfo.h
new file mode 100644
index 000000000..2128ba903
--- /dev/null
+++ b/arch/mips/include/asm/bootinfo.h
@@ -0,0 +1,189 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file COPYING in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995, 1996, 2003 by Ralf Baechle
+ * Copyright (C) 1995, 1996 Andreas Busse
+ * Copyright (C) 1995, 1996 Stoned Elipot
+ * Copyright (C) 1995, 1996 Paul M. Antoine.
+ * Copyright (C) 2009       Zhang Le
+ */
+#ifndef _ASM_BOOTINFO_H
+#define _ASM_BOOTINFO_H
+
+#include <linux/types.h>
+#include <asm/setup.h>
+
+/*
+ * The MACH_ IDs are sort of equivalent to PCI product IDs.  As such the
+ * numbers do not necessarily reflect technical relations or similarities
+ * between systems.
+ */
+
+/*
+ * Valid machtype values for group unknown
+ */
+#define  MACH_UNKNOWN		0	/* whatever...			*/
+
+/*
+ * Valid machtype for group DEC
+ */
+#define  MACH_DSUNKNOWN		0
+#define  MACH_DS23100		1	/* DECstation 2100 or 3100	*/
+#define  MACH_DS5100		2	/* DECsystem 5100		*/
+#define  MACH_DS5000_200	3	/* DECstation 5000/200		*/
+#define  MACH_DS5000_1XX	4	/* DECstation 5000/120, 125, 133, 150 */
+#define  MACH_DS5000_XX		5	/* DECstation 5000/20, 25, 33, 50 */
+#define  MACH_DS5000_2X0	6	/* DECstation 5000/240, 260	*/
+#define  MACH_DS5400		7	/* DECsystem 5400		*/
+#define  MACH_DS5500		8	/* DECsystem 5500		*/
+#define  MACH_DS5800		9	/* DECsystem 5800		*/
+#define  MACH_DS5900		10	/* DECsystem 5900		*/
+
+/*
+ * Valid machtype for group Mikrotik
+ */
+#define MACH_MIKROTIK_RB532	0	/* Mikrotik RouterBoard 532	*/
+#define MACH_MIKROTIK_RB532A	1	/* Mikrotik RouterBoard 532A	*/
+
+/*
+ * Valid machtype for Loongson family
+ */
+enum loongson2ef_machine_type {
+	MACH_LOONGSON_UNKNOWN,
+	MACH_LEMOTE_FL2E,
+	MACH_LEMOTE_FL2F,
+	MACH_LEMOTE_ML2F7,
+	MACH_LEMOTE_YL2F89,
+	MACH_DEXXON_GDIUM2F10,
+	MACH_LEMOTE_NAS,
+	MACH_LEMOTE_LL2F,
+	MACH_LOONGSON_END
+};
+
+/*
+ * Valid machtype for group INGENIC
+ */
+enum ingenic_machine_type {
+	MACH_INGENIC_UNKNOWN,
+	MACH_INGENIC_JZ4720,
+	MACH_INGENIC_JZ4725,
+	MACH_INGENIC_JZ4725B,
+	MACH_INGENIC_JZ4730,
+	MACH_INGENIC_JZ4740,
+	MACH_INGENIC_JZ4750,
+	MACH_INGENIC_JZ4755,
+	MACH_INGENIC_JZ4760,
+	MACH_INGENIC_JZ4760B,
+	MACH_INGENIC_JZ4770,
+	MACH_INGENIC_JZ4775,
+	MACH_INGENIC_JZ4780,
+	MACH_INGENIC_X1000,
+	MACH_INGENIC_X1000E,
+	MACH_INGENIC_X1830,
+	MACH_INGENIC_X2000,
+	MACH_INGENIC_X2000E,
+	MACH_INGENIC_X2000H,
+	MACH_INGENIC_X2100,
+};
+
+extern char *system_type;
+const char *get_system_type(void);
+
+extern unsigned long mips_machtype;
+
+extern void detect_memory_region(phys_addr_t start, phys_addr_t sz_min,  phys_addr_t sz_max);
+
+extern void prom_init(void);
+extern void prom_free_prom_memory(void);
+extern void prom_cleanup(void);
+
+extern void free_init_pages(const char *what,
+			    unsigned long begin, unsigned long end);
+
+extern void (*free_init_pages_eva)(void *begin, void *end);
+
+/*
+ * Initial kernel command line, usually setup by prom_init()
+ */
+extern char arcs_cmdline[COMMAND_LINE_SIZE];
+
+/*
+ * Registers a0, a1, a2 and a3 as passed to the kernel entry by firmware
+ */
+extern unsigned long fw_arg0, fw_arg1, fw_arg2, fw_arg3;
+
+#ifdef CONFIG_USE_OF
+#include <linux/libfdt.h>
+#include <linux/of_fdt.h>
+
+extern char __appended_dtb[];
+
+static inline void *get_fdt(void)
+{
+	if (IS_ENABLED(CONFIG_MIPS_RAW_APPENDED_DTB) ||
+	    IS_ENABLED(CONFIG_MIPS_ELF_APPENDED_DTB))
+		if (fdt_magic(&__appended_dtb) == FDT_MAGIC)
+			return &__appended_dtb;
+
+	if (fw_arg0 == -2) /* UHI interface */
+		return (void *)fw_arg1;
+
+	if (IS_ENABLED(CONFIG_BUILTIN_DTB))
+		if (&__dtb_start != &__dtb_end)
+			return &__dtb_start;
+
+	return NULL;
+}
+#endif
+
+/*
+ * Platform memory detection hook called by arch_mem_init()
+ */
+extern void plat_mem_setup(void);
+
+#ifdef CONFIG_SWIOTLB
+/*
+ * Optional platform hook to call swiotlb_setup().
+ */
+extern void plat_swiotlb_setup(void);
+
+#else
+
+static inline void plat_swiotlb_setup(void) {}
+
+#endif /* CONFIG_SWIOTLB */
+
+#ifdef CONFIG_USE_OF
+/**
+ * plat_get_fdt() - Return a pointer to the platform's device tree blob
+ *
+ * This function provides a platform independent API to get a pointer to the
+ * flattened device tree blob. The interface between bootloader and kernel
+ * is not consistent across platforms so it is necessary to provide this
+ * API such that common startup code can locate the FDT.
+ *
+ * This is used by the KASLR code to get command line arguments and random
+ * seed from the device tree. Any platform wishing to use KASLR should
+ * provide this API and select SYS_SUPPORTS_RELOCATABLE.
+ *
+ * Return: Pointer to the flattened device tree blob.
+ */
+extern void *plat_get_fdt(void);
+
+#ifdef CONFIG_RELOCATABLE
+
+/**
+ * plat_fdt_relocated() - Update platform's information about relocated dtb
+ *
+ * This function provides a platform-independent API to set platform's
+ * information about relocated DTB if it needs to be moved due to kernel
+ * relocation occurring at boot.
+ */
+void plat_fdt_relocated(void *new_location);
+
+#endif /* CONFIG_RELOCATABLE */
+#endif /* CONFIG_USE_OF */
+
+#endif /* _ASM_BOOTINFO_H */
diff --git a/arch/mips/include/asm/branch.h b/arch/mips/include/asm/branch.h
new file mode 100644
index 000000000..fa3dcbf56
--- /dev/null
+++ b/arch/mips/include/asm/branch.h
@@ -0,0 +1,103 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1996, 1997, 1998, 2001 by Ralf Baechle
+ */
+#ifndef _ASM_BRANCH_H
+#define _ASM_BRANCH_H
+
+#include <asm/cpu-features.h>
+#include <asm/mipsregs.h>
+#include <asm/ptrace.h>
+#include <asm/inst.h>
+
+extern int __isa_exception_epc(struct pt_regs *regs);
+extern int __compute_return_epc(struct pt_regs *regs);
+extern int __compute_return_epc_for_insn(struct pt_regs *regs,
+					 union mips_instruction insn);
+extern int __microMIPS_compute_return_epc(struct pt_regs *regs);
+extern int __MIPS16e_compute_return_epc(struct pt_regs *regs);
+
+/*
+ * microMIPS bitfields
+ */
+#define MM_POOL32A_MINOR_MASK	0x3f
+#define MM_POOL32A_MINOR_SHIFT	0x6
+#define MM_MIPS32_COND_FC	0x30
+
+int isBranchInstr(struct pt_regs *regs,
+	struct mm_decoded_insn dec_insn, unsigned long *contpc);
+
+extern int __mm_isBranchInstr(struct pt_regs *regs,
+	struct mm_decoded_insn dec_insn, unsigned long *contpc);
+
+static inline int mm_isBranchInstr(struct pt_regs *regs,
+	struct mm_decoded_insn dec_insn, unsigned long *contpc)
+{
+	if (!cpu_has_mmips)
+		return 0;
+
+	return __mm_isBranchInstr(regs, dec_insn, contpc);
+}
+
+static inline int delay_slot(struct pt_regs *regs)
+{
+	return regs->cp0_cause & CAUSEF_BD;
+}
+
+static inline void clear_delay_slot(struct pt_regs *regs)
+{
+	regs->cp0_cause &= ~CAUSEF_BD;
+}
+
+static inline void set_delay_slot(struct pt_regs *regs)
+{
+	regs->cp0_cause |= CAUSEF_BD;
+}
+
+static inline unsigned long exception_epc(struct pt_regs *regs)
+{
+	if (likely(!delay_slot(regs)))
+		return regs->cp0_epc;
+
+	if (get_isa16_mode(regs->cp0_epc))
+		return __isa_exception_epc(regs);
+
+	return regs->cp0_epc + 4;
+}
+
+#define BRANCH_LIKELY_TAKEN 0x0001
+
+static inline int compute_return_epc(struct pt_regs *regs)
+{
+	if (get_isa16_mode(regs->cp0_epc)) {
+		if (cpu_has_mmips)
+			return __microMIPS_compute_return_epc(regs);
+		if (cpu_has_mips16)
+			return __MIPS16e_compute_return_epc(regs);
+	} else if (!delay_slot(regs)) {
+		regs->cp0_epc += 4;
+		return 0;
+	}
+
+	return __compute_return_epc(regs);
+}
+
+static inline int MIPS16e_compute_return_epc(struct pt_regs *regs,
+					     union mips16e_instruction *inst)
+{
+	if (likely(!delay_slot(regs))) {
+		if (inst->ri.opcode == MIPS16e_extend_op) {
+			regs->cp0_epc += 4;
+			return 0;
+		}
+		regs->cp0_epc += 2;
+		return 0;
+	}
+
+	return __MIPS16e_compute_return_epc(regs);
+}
+
+#endif /* _ASM_BRANCH_H */
diff --git a/arch/mips/include/asm/break.h b/arch/mips/include/asm/break.h
new file mode 100644
index 000000000..0ef11429a
--- /dev/null
+++ b/arch/mips/include/asm/break.h
@@ -0,0 +1,26 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995, 2003 by Ralf Baechle
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ */
+#ifndef __ASM_BREAK_H
+#define __ASM_BREAK_H
+
+#ifdef __UAPI_ASM_BREAK_H
+#error "Error: Do not directly include <uapi/asm/break.h>"
+#endif
+#include <uapi/asm/break.h>
+
+/*
+ * Break codes used internally to the kernel.
+ */
+#define BRK_KDB		513	/* Used in KDB_ENTER() */
+#define BRK_MEMU	514	/* Used by FPU emulator */
+#define BRK_KPROBE_BP	515	/* Kprobe break */
+#define BRK_KPROBE_SSTEPBP 516	/* Kprobe single step software implementation */
+#define BRK_MULOVF	1023	/* Multiply overflow */
+
+#endif /* __ASM_BREAK_H */
diff --git a/arch/mips/include/asm/bug.h b/arch/mips/include/asm/bug.h
new file mode 100644
index 000000000..745dc160a
--- /dev/null
+++ b/arch/mips/include/asm/bug.h
@@ -0,0 +1,44 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_BUG_H
+#define __ASM_BUG_H
+
+#include <linux/compiler.h>
+#include <asm/sgidefs.h>
+
+#ifdef CONFIG_BUG
+
+#include <asm/break.h>
+
+static inline void __noreturn BUG(void)
+{
+	__asm__ __volatile__("break %0" : : "i" (BRK_BUG));
+	unreachable();
+}
+
+#define HAVE_ARCH_BUG
+
+#if (_MIPS_ISA > _MIPS_ISA_MIPS1)
+
+static inline void  __BUG_ON(unsigned long condition)
+{
+	if (__builtin_constant_p(condition)) {
+		if (condition)
+			BUG();
+		else
+			return;
+	}
+	__asm__ __volatile__("tne $0, %0, %1"
+			     : : "r" (condition), "i" (BRK_BUG));
+}
+
+#define BUG_ON(C) __BUG_ON((unsigned long)(C))
+
+#define HAVE_ARCH_BUG_ON
+
+#endif /* _MIPS_ISA > _MIPS_ISA_MIPS1 */
+
+#endif
+
+#include <asm-generic/bug.h>
+
+#endif /* __ASM_BUG_H */
diff --git a/arch/mips/include/asm/bugs.h b/arch/mips/include/asm/bugs.h
new file mode 100644
index 000000000..8d4cf2986
--- /dev/null
+++ b/arch/mips/include/asm/bugs.h
@@ -0,0 +1,36 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2007  Maciej W. Rozycki
+ */
+#ifndef _ASM_BUGS_H
+#define _ASM_BUGS_H
+
+#include <linux/bug.h>
+#include <linux/smp.h>
+
+#include <asm/cpu.h>
+#include <asm/cpu-info.h>
+
+extern int daddiu_bug;
+
+extern void check_bugs64_early(void);
+
+extern void check_bugs32(void);
+extern void check_bugs64(void);
+
+static inline void check_bugs_early(void)
+{
+	if (IS_ENABLED(CONFIG_CPU_R4X00_BUGS64))
+		check_bugs64_early();
+}
+
+static inline int r4k_daddiu_bug(void)
+{
+	if (!IS_ENABLED(CONFIG_CPU_R4X00_BUGS64))
+		return 0;
+
+	WARN_ON(daddiu_bug < 0);
+	return daddiu_bug != 0;
+}
+
+#endif /* _ASM_BUGS_H */
diff --git a/arch/mips/include/asm/cache.h b/arch/mips/include/asm/cache.h
new file mode 100644
index 000000000..29187e12b
--- /dev/null
+++ b/arch/mips/include/asm/cache.h
@@ -0,0 +1,19 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1997, 98, 99, 2000, 2003 Ralf Baechle
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_CACHE_H
+#define _ASM_CACHE_H
+
+#include <kmalloc.h>
+
+#define L1_CACHE_SHIFT		CONFIG_MIPS_L1_CACHE_SHIFT
+#define L1_CACHE_BYTES		(1 << L1_CACHE_SHIFT)
+
+#define __read_mostly __section(".data..read_mostly")
+
+#endif /* _ASM_CACHE_H */
diff --git a/arch/mips/include/asm/cacheflush.h b/arch/mips/include/asm/cacheflush.h
new file mode 100644
index 000000000..b3dc9c589
--- /dev/null
+++ b/arch/mips/include/asm/cacheflush.h
@@ -0,0 +1,147 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994, 95, 96, 97, 98, 99, 2000, 01, 02, 03 by Ralf Baechle
+ * Copyright (C) 1999, 2000, 2001 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_CACHEFLUSH_H
+#define _ASM_CACHEFLUSH_H
+
+/* Keep includes the same across arches.  */
+#include <linux/mm.h>
+#include <asm/cpu-features.h>
+
+/* Cache flushing:
+ *
+ *  - flush_cache_all() flushes entire cache
+ *  - flush_cache_mm(mm) flushes the specified mm context's cache lines
+ *  - flush_cache_dup mm(mm) handles cache flushing when forking
+ *  - flush_cache_page(mm, vmaddr, pfn) flushes a single page
+ *  - flush_cache_range(vma, start, end) flushes a range of pages
+ *  - flush_icache_range(start, end) flush a range of instructions
+ *  - flush_dcache_page(pg) flushes(wback&invalidates) a page for dcache
+ *
+ * MIPS specific flush operations:
+ *
+ *  - flush_icache_all() flush the entire instruction cache
+ *  - flush_data_cache_page() flushes a page from the data cache
+ *  - __flush_icache_user_range(start, end) flushes range of user instructions
+ */
+
+ /*
+ * This flag is used to indicate that the page pointed to by a pte
+ * is dirty and requires cleaning before returning it to the user.
+ */
+#define PG_dcache_dirty			PG_arch_1
+
+#define Page_dcache_dirty(page)		\
+	test_bit(PG_dcache_dirty, &(page)->flags)
+#define SetPageDcacheDirty(page)	\
+	set_bit(PG_dcache_dirty, &(page)->flags)
+#define ClearPageDcacheDirty(page)	\
+	clear_bit(PG_dcache_dirty, &(page)->flags)
+
+extern void (*flush_cache_all)(void);
+extern void (*__flush_cache_all)(void);
+extern void (*flush_cache_mm)(struct mm_struct *mm);
+#define flush_cache_dup_mm(mm)	do { (void) (mm); } while (0)
+extern void (*flush_cache_range)(struct vm_area_struct *vma,
+	unsigned long start, unsigned long end);
+extern void (*flush_cache_page)(struct vm_area_struct *vma, unsigned long page, unsigned long pfn);
+extern void __flush_dcache_page(struct page *page);
+
+#define ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE 1
+static inline void flush_dcache_page(struct page *page)
+{
+	if (cpu_has_dc_aliases)
+		__flush_dcache_page(page);
+	else if (!cpu_has_ic_fills_f_dc)
+		SetPageDcacheDirty(page);
+}
+
+#define flush_dcache_mmap_lock(mapping)		do { } while (0)
+#define flush_dcache_mmap_unlock(mapping)	do { } while (0)
+
+#define ARCH_HAS_FLUSH_ANON_PAGE
+extern void __flush_anon_page(struct page *, unsigned long);
+static inline void flush_anon_page(struct vm_area_struct *vma,
+	struct page *page, unsigned long vmaddr)
+{
+	if (cpu_has_dc_aliases && PageAnon(page))
+		__flush_anon_page(page, vmaddr);
+}
+
+static inline void flush_icache_page(struct vm_area_struct *vma,
+	struct page *page)
+{
+}
+
+extern void (*flush_icache_range)(unsigned long start, unsigned long end);
+extern void (*local_flush_icache_range)(unsigned long start, unsigned long end);
+extern void (*__flush_icache_user_range)(unsigned long start,
+					 unsigned long end);
+extern void (*__local_flush_icache_user_range)(unsigned long start,
+					       unsigned long end);
+
+extern void (*__flush_cache_vmap)(void);
+
+static inline void flush_cache_vmap(unsigned long start, unsigned long end)
+{
+	if (cpu_has_dc_aliases)
+		__flush_cache_vmap();
+}
+
+extern void (*__flush_cache_vunmap)(void);
+
+static inline void flush_cache_vunmap(unsigned long start, unsigned long end)
+{
+	if (cpu_has_dc_aliases)
+		__flush_cache_vunmap();
+}
+
+extern void copy_to_user_page(struct vm_area_struct *vma,
+	struct page *page, unsigned long vaddr, void *dst, const void *src,
+	unsigned long len);
+
+extern void copy_from_user_page(struct vm_area_struct *vma,
+	struct page *page, unsigned long vaddr, void *dst, const void *src,
+	unsigned long len);
+
+extern void (*flush_icache_all)(void);
+extern void (*local_flush_data_cache_page)(void * addr);
+extern void (*flush_data_cache_page)(unsigned long addr);
+
+/* Run kernel code uncached, useful for cache probing functions. */
+unsigned long run_uncached(void *func);
+
+extern void *kmap_coherent(struct page *page, unsigned long addr);
+extern void kunmap_coherent(void);
+extern void *kmap_noncoherent(struct page *page, unsigned long addr);
+
+static inline void kunmap_noncoherent(void)
+{
+	kunmap_coherent();
+}
+
+#define ARCH_IMPLEMENTS_FLUSH_KERNEL_VMAP_RANGE 1
+/*
+ * For now flush_kernel_vmap_range and invalidate_kernel_vmap_range both do a
+ * cache writeback and invalidate operation.
+ */
+extern void (*__flush_kernel_vmap_range)(unsigned long vaddr, int size);
+
+static inline void flush_kernel_vmap_range(void *vaddr, int size)
+{
+	if (cpu_has_dc_aliases)
+		__flush_kernel_vmap_range((unsigned long) vaddr, size);
+}
+
+static inline void invalidate_kernel_vmap_range(void *vaddr, int size)
+{
+	if (cpu_has_dc_aliases)
+		__flush_kernel_vmap_range((unsigned long) vaddr, size);
+}
+
+#endif /* _ASM_CACHEFLUSH_H */
diff --git a/arch/mips/include/asm/cacheops.h b/arch/mips/include/asm/cacheops.h
new file mode 100644
index 000000000..50253efec
--- /dev/null
+++ b/arch/mips/include/asm/cacheops.h
@@ -0,0 +1,116 @@
+/*
+ * Cache operations for the cache instruction.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * (C) Copyright 1996, 97, 99, 2002, 03 Ralf Baechle
+ * (C) Copyright 1999 Silicon Graphics, Inc.
+ */
+#ifndef __ASM_CACHEOPS_H
+#define __ASM_CACHEOPS_H
+
+/*
+ * Most cache ops are split into a 2 bit field identifying the cache, and a 3
+ * bit field identifying the cache operation.
+ */
+#define CacheOp_Cache			0x03
+#define CacheOp_Op			0x1c
+
+#define Cache_I				0x00
+#define Cache_D				0x01
+#define Cache_T				0x02
+#define Cache_V				0x02 /* Loongson-3 */
+#define Cache_S				0x03
+
+#define Index_Writeback_Inv		0x00
+#define Index_Load_Tag			0x04
+#define Index_Store_Tag			0x08
+#define Hit_Invalidate			0x10
+#define Hit_Writeback_Inv		0x14	/* not with Cache_I though */
+#define Hit_Writeback			0x18
+
+/*
+ * Cache Operations available on all MIPS processors with R4000-style caches
+ */
+#define Index_Invalidate_I		(Cache_I | Index_Writeback_Inv)
+#define Index_Writeback_Inv_D		(Cache_D | Index_Writeback_Inv)
+#define Index_Load_Tag_I		(Cache_I | Index_Load_Tag)
+#define Index_Load_Tag_D		(Cache_D | Index_Load_Tag)
+#define Index_Store_Tag_I		(Cache_I | Index_Store_Tag)
+#define Index_Store_Tag_D		(Cache_D | Index_Store_Tag)
+#define Hit_Invalidate_I		(Cache_I | Hit_Invalidate)
+#define Hit_Invalidate_D		(Cache_D | Hit_Invalidate)
+#define Hit_Writeback_Inv_D		(Cache_D | Hit_Writeback_Inv)
+
+/*
+ * R4000-specific cacheops
+ */
+#define Create_Dirty_Excl_D		(Cache_D | 0x0c)
+#define Fill_I				(Cache_I | 0x14)
+#define Hit_Writeback_I			(Cache_I | Hit_Writeback)
+#define Hit_Writeback_D			(Cache_D | Hit_Writeback)
+
+/*
+ * R4000SC and R4400SC-specific cacheops
+ */
+#define Cache_SI			0x02
+#define Cache_SD			0x03
+
+#define Index_Invalidate_SI		(Cache_SI | Index_Writeback_Inv)
+#define Index_Writeback_Inv_SD		(Cache_SD | Index_Writeback_Inv)
+#define Index_Load_Tag_SI		(Cache_SI | Index_Load_Tag)
+#define Index_Load_Tag_SD		(Cache_SD | Index_Load_Tag)
+#define Index_Store_Tag_SI		(Cache_SI | Index_Store_Tag)
+#define Index_Store_Tag_SD		(Cache_SD | Index_Store_Tag)
+#define Create_Dirty_Excl_SD		(Cache_SD | 0x0c)
+#define Hit_Invalidate_SI		(Cache_SI | Hit_Invalidate)
+#define Hit_Invalidate_SD		(Cache_SD | Hit_Invalidate)
+#define Hit_Writeback_Inv_SD		(Cache_SD | Hit_Writeback_Inv)
+#define Hit_Writeback_SD		(Cache_SD | Hit_Writeback)
+#define Hit_Set_Virtual_SI		(Cache_SI | 0x1c)
+#define Hit_Set_Virtual_SD		(Cache_SD | 0x1c)
+
+/*
+ * R5000-specific cacheops
+ */
+#define R5K_Page_Invalidate_S		(Cache_S | 0x14)
+
+/*
+ * RM7000-specific cacheops
+ */
+#define Page_Invalidate_T		(Cache_T | 0x14)
+#define Index_Store_Tag_T		(Cache_T | Index_Store_Tag)
+#define Index_Load_Tag_T		(Cache_T | Index_Load_Tag)
+
+/*
+ * R10000-specific cacheops
+ *
+ * Cacheops 0x02, 0x06, 0x0a, 0x0c-0x0e, 0x16, 0x1a and 0x1e are unused.
+ * Most of the _S cacheops are identical to the R4000SC _SD cacheops.
+ */
+#define Index_Writeback_Inv_S		(Cache_S | Index_Writeback_Inv)
+#define Index_Load_Tag_S		(Cache_S | Index_Load_Tag)
+#define Index_Store_Tag_S		(Cache_S | Index_Store_Tag)
+#define Hit_Invalidate_S		(Cache_S | Hit_Invalidate)
+#define Cache_Barrier			0x14
+#define Hit_Writeback_Inv_S		(Cache_S | Hit_Writeback_Inv)
+#define Index_Load_Data_I		(Cache_I | 0x18)
+#define Index_Load_Data_D		(Cache_D | 0x18)
+#define Index_Load_Data_S		(Cache_S | 0x18)
+#define Index_Store_Data_I		(Cache_I | 0x1c)
+#define Index_Store_Data_D		(Cache_D | 0x1c)
+#define Index_Store_Data_S		(Cache_S | 0x1c)
+
+/*
+ * Loongson2-specific cacheops
+ */
+#define Hit_Invalidate_I_Loongson2	(Cache_I | 0x00)
+
+/*
+ * Loongson3-specific cacheops
+ */
+#define Index_Writeback_Inv_V		(Cache_V | Index_Writeback_Inv)
+
+#endif	/* __ASM_CACHEOPS_H */
diff --git a/arch/mips/include/asm/cdmm.h b/arch/mips/include/asm/cdmm.h
new file mode 100644
index 000000000..c06dbf8ba
--- /dev/null
+++ b/arch/mips/include/asm/cdmm.h
@@ -0,0 +1,109 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2014 Imagination Technologies Ltd.
+ */
+#ifndef __ASM_CDMM_H
+#define __ASM_CDMM_H
+
+#include <linux/device.h>
+#include <linux/mod_devicetable.h>
+
+/**
+ * struct mips_cdmm_device - Represents a single device on a CDMM bus.
+ * @dev:	Driver model device object.
+ * @cpu:	CPU which can access this device.
+ * @res:	MMIO resource.
+ * @type:	Device type identifier.
+ * @rev:	Device revision number.
+ */
+struct mips_cdmm_device {
+	struct device		dev;
+	unsigned int		cpu;
+	struct resource		res;
+	unsigned int		type;
+	unsigned int		rev;
+};
+
+/**
+ * struct mips_cdmm_driver - Represents a driver for a CDMM device.
+ * @drv:	Driver model driver object.
+ * @probe	Callback for probing newly discovered devices.
+ * @remove:	Callback to remove the device.
+ * @shutdown:	Callback on system shutdown.
+ * @cpu_down:	Callback when the parent CPU is going down.
+ *		Any CPU pinned threads/timers should be disabled.
+ * @cpu_up:	Callback when the parent CPU is coming back up again.
+ *		CPU pinned threads/timers can be restarted.
+ * @id_table:	Table for CDMM IDs to match against.
+ */
+struct mips_cdmm_driver {
+	struct device_driver	drv;
+	int			(*probe)(struct mips_cdmm_device *);
+	int			(*remove)(struct mips_cdmm_device *);
+	void			(*shutdown)(struct mips_cdmm_device *);
+	int			(*cpu_down)(struct mips_cdmm_device *);
+	int			(*cpu_up)(struct mips_cdmm_device *);
+	const struct mips_cdmm_device_id *id_table;
+};
+
+/**
+ * mips_cdmm_phys_base() - Choose a physical base address for CDMM region.
+ *
+ * Picking a suitable physical address at which to map the CDMM region is
+ * platform specific, so this function can be defined by platform code to
+ * pick a suitable value if none is configured by the bootloader.
+ *
+ * This address must be 32kB aligned, and the region occupies a maximum of 32kB
+ * of physical address space which must not be used for anything else.
+ *
+ * Returns:	Physical base address for CDMM region, or 0 on failure.
+ */
+phys_addr_t mips_cdmm_phys_base(void);
+
+extern struct bus_type mips_cdmm_bustype;
+void __iomem *mips_cdmm_early_probe(unsigned int dev_type);
+
+#define to_mips_cdmm_device(d)	container_of(d, struct mips_cdmm_device, dev)
+
+#define mips_cdmm_get_drvdata(d)	dev_get_drvdata(&d->dev)
+#define mips_cdmm_set_drvdata(d, p)	dev_set_drvdata(&d->dev, p)
+
+int mips_cdmm_driver_register(struct mips_cdmm_driver *);
+void mips_cdmm_driver_unregister(struct mips_cdmm_driver *);
+
+/*
+ * module_mips_cdmm_driver() - Helper macro for drivers that don't do
+ * anything special in module init/exit.  This eliminates a lot of
+ * boilerplate.  Each module may only use this macro once, and
+ * calling it replaces module_init() and module_exit()
+ */
+#define module_mips_cdmm_driver(__mips_cdmm_driver) \
+	module_driver(__mips_cdmm_driver, mips_cdmm_driver_register, \
+			mips_cdmm_driver_unregister)
+
+/*
+ * builtin_mips_cdmm_driver() - Helper macro for drivers that don't do anything
+ * special in init and have no exit. This eliminates some boilerplate. Each
+ * driver may only use this macro once, and calling it replaces device_initcall
+ * (or in some cases, the legacy __initcall). This is meant to be a direct
+ * parallel of module_mips_cdmm_driver() above but without the __exit stuff that
+ * is not used for builtin cases.
+ */
+#define builtin_mips_cdmm_driver(__mips_cdmm_driver) \
+	builtin_driver(__mips_cdmm_driver, mips_cdmm_driver_register)
+
+/* drivers/tty/mips_ejtag_fdc.c */
+
+#ifdef CONFIG_MIPS_EJTAG_FDC_EARLYCON
+int setup_early_fdc_console(void);
+#else
+static inline int setup_early_fdc_console(void)
+{
+	return -ENODEV;
+}
+#endif
+
+#endif /* __ASM_CDMM_H */
diff --git a/arch/mips/include/asm/cevt-r4k.h b/arch/mips/include/asm/cevt-r4k.h
new file mode 100644
index 000000000..2e13a038d
--- /dev/null
+++ b/arch/mips/include/asm/cevt-r4k.h
@@ -0,0 +1,29 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Kevin D. Kissell
+ */
+
+/*
+ * Definitions used for common event timer implementation
+ * for MIPS 4K-type processors and their MIPS MT variants.
+ * Avoids unsightly extern declarations in C files.
+ */
+#ifndef __ASM_CEVT_R4K_H
+#define __ASM_CEVT_R4K_H
+
+#include <linux/clockchips.h>
+#include <asm/time.h>
+
+DECLARE_PER_CPU(struct clock_event_device, mips_clockevent_device);
+
+void mips_event_handler(struct clock_event_device *dev);
+int c0_compare_int_usable(void);
+irqreturn_t c0_compare_interrupt(int, void *);
+
+extern struct irqaction c0_compare_irqaction;
+extern int cp0_timer_irq_installed;
+
+#endif /* __ASM_CEVT_R4K_H */
diff --git a/arch/mips/include/asm/checksum.h b/arch/mips/include/asm/checksum.h
new file mode 100644
index 000000000..4044eaf98
--- /dev/null
+++ b/arch/mips/include/asm/checksum.h
@@ -0,0 +1,252 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995, 96, 97, 98, 99, 2001 by Ralf Baechle
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ * Copyright (C) 2001 Thiemo Seufer.
+ * Copyright (C) 2002 Maciej W. Rozycki
+ * Copyright (C) 2014 Imagination Technologies Ltd.
+ */
+#ifndef _ASM_CHECKSUM_H
+#define _ASM_CHECKSUM_H
+
+#ifdef CONFIG_GENERIC_CSUM
+#include <asm-generic/checksum.h>
+#else
+
+#include <linux/in6.h>
+
+#include <linux/uaccess.h>
+
+/*
+ * computes the checksum of a memory block at buff, length len,
+ * and adds in "sum" (32-bit)
+ *
+ * returns a 32-bit number suitable for feeding into itself
+ * or csum_tcpudp_magic
+ *
+ * this function must be called with even lengths, except
+ * for the last fragment, which may be odd
+ *
+ * it's best to have buff aligned on a 32-bit boundary
+ */
+__wsum csum_partial(const void *buff, int len, __wsum sum);
+
+__wsum __csum_partial_copy_from_user(const void __user *src, void *dst, int len);
+__wsum __csum_partial_copy_to_user(const void *src, void __user *dst, int len);
+
+#define _HAVE_ARCH_COPY_AND_CSUM_FROM_USER
+static inline
+__wsum csum_and_copy_from_user(const void __user *src, void *dst, int len)
+{
+	might_fault();
+	if (!access_ok(src, len))
+		return 0;
+	return __csum_partial_copy_from_user(src, dst, len);
+}
+
+/*
+ * Copy and checksum to user
+ */
+#define HAVE_CSUM_COPY_USER
+static inline
+__wsum csum_and_copy_to_user(const void *src, void __user *dst, int len)
+{
+	might_fault();
+	if (!access_ok(dst, len))
+		return 0;
+	return __csum_partial_copy_to_user(src, dst, len);
+}
+
+/*
+ * the same as csum_partial, but copies from user space (but on MIPS
+ * we have just one address space, so this is identical to the above)
+ */
+#define _HAVE_ARCH_CSUM_AND_COPY
+__wsum __csum_partial_copy_nocheck(const void *src, void *dst, int len);
+static inline __wsum csum_partial_copy_nocheck(const void *src, void *dst, int len)
+{
+	return __csum_partial_copy_nocheck(src, dst, len);
+}
+
+/*
+ *	Fold a partial checksum without adding pseudo headers
+ */
+static inline __sum16 csum_fold(__wsum csum)
+{
+	u32 sum = (__force u32)csum;
+
+	sum += (sum << 16);
+	csum = (__force __wsum)(sum < (__force u32)csum);
+	sum >>= 16;
+	sum += (__force u32)csum;
+
+	return (__force __sum16)~sum;
+}
+#define csum_fold csum_fold
+
+/*
+ *	This is a version of ip_compute_csum() optimized for IP headers,
+ *	which always checksum on 4 octet boundaries.
+ *
+ *	By Jorge Cwik <jorge@laser.satlink.net>, adapted for linux by
+ *	Arnt Gulbrandsen.
+ */
+static inline __sum16 ip_fast_csum(const void *iph, unsigned int ihl)
+{
+	const unsigned int *word = iph;
+	const unsigned int *stop = word + ihl;
+	unsigned int csum;
+	int carry;
+
+	csum = word[0];
+	csum += word[1];
+	carry = (csum < word[1]);
+	csum += carry;
+
+	csum += word[2];
+	carry = (csum < word[2]);
+	csum += carry;
+
+	csum += word[3];
+	carry = (csum < word[3]);
+	csum += carry;
+
+	word += 4;
+	do {
+		csum += *word;
+		carry = (csum < *word);
+		csum += carry;
+		word++;
+	} while (word != stop);
+
+	return csum_fold(csum);
+}
+#define ip_fast_csum ip_fast_csum
+
+static inline __wsum csum_tcpudp_nofold(__be32 saddr, __be32 daddr,
+					__u32 len, __u8 proto,
+					__wsum isum)
+{
+	const unsigned int sh32 = IS_ENABLED(CONFIG_64BIT) ? 32 : 0;
+	unsigned long sum = (__force unsigned long)daddr;
+	unsigned long tmp;
+	__u32 osum;
+
+	tmp = (__force unsigned long)saddr;
+	sum += tmp;
+
+	if (IS_ENABLED(CONFIG_32BIT))
+		sum += sum < tmp;
+
+	/*
+	 * We know PROTO + LEN has the sign bit clear, so cast to a signed
+	 * type to avoid an extraneous zero-extension where TMP is 64-bit.
+	 */
+	tmp = (__s32)(proto + len);
+	tmp <<= IS_ENABLED(CONFIG_CPU_LITTLE_ENDIAN) ? 8 : 0;
+	sum += tmp;
+	if (IS_ENABLED(CONFIG_32BIT))
+		sum += sum < tmp;
+
+	tmp = (__force unsigned long)isum;
+	sum += tmp;
+
+	if (IS_ENABLED(CONFIG_32BIT)) {
+		sum += sum < tmp;
+		osum = sum;
+	} else if (IS_ENABLED(CONFIG_64BIT)) {
+		tmp = sum << sh32;
+		sum += tmp;
+		osum = sum < tmp;
+		osum += sum >> sh32;
+	} else {
+		BUILD_BUG();
+	}
+
+	return (__force __wsum)osum;
+}
+#define csum_tcpudp_nofold csum_tcpudp_nofold
+
+/*
+ * this routine is used for miscellaneous IP-like checksums, mainly
+ * in icmp.c
+ */
+static inline __sum16 ip_compute_csum(const void *buff, int len)
+{
+	return csum_fold(csum_partial(buff, len, 0));
+}
+
+#define _HAVE_ARCH_IPV6_CSUM
+static __inline__ __sum16 csum_ipv6_magic(const struct in6_addr *saddr,
+					  const struct in6_addr *daddr,
+					  __u32 len, __u8 proto,
+					  __wsum sum)
+{
+	__wsum tmp;
+
+	__asm__(
+	"	.set	push		# csum_ipv6_magic\n"
+	"	.set	noreorder	\n"
+	"	.set	noat		\n"
+	"	addu	%0, %5		# proto (long in network byte order)\n"
+	"	sltu	$1, %0, %5	\n"
+	"	addu	%0, $1		\n"
+
+	"	addu	%0, %6		# csum\n"
+	"	sltu	$1, %0, %6	\n"
+	"	lw	%1, 0(%2)	# four words source address\n"
+	"	addu	%0, $1		\n"
+	"	addu	%0, %1		\n"
+	"	sltu	$1, %0, %1	\n"
+
+	"	lw	%1, 4(%2)	\n"
+	"	addu	%0, $1		\n"
+	"	addu	%0, %1		\n"
+	"	sltu	$1, %0, %1	\n"
+
+	"	lw	%1, 8(%2)	\n"
+	"	addu	%0, $1		\n"
+	"	addu	%0, %1		\n"
+	"	sltu	$1, %0, %1	\n"
+
+	"	lw	%1, 12(%2)	\n"
+	"	addu	%0, $1		\n"
+	"	addu	%0, %1		\n"
+	"	sltu	$1, %0, %1	\n"
+
+	"	lw	%1, 0(%3)	\n"
+	"	addu	%0, $1		\n"
+	"	addu	%0, %1		\n"
+	"	sltu	$1, %0, %1	\n"
+
+	"	lw	%1, 4(%3)	\n"
+	"	addu	%0, $1		\n"
+	"	addu	%0, %1		\n"
+	"	sltu	$1, %0, %1	\n"
+
+	"	lw	%1, 8(%3)	\n"
+	"	addu	%0, $1		\n"
+	"	addu	%0, %1		\n"
+	"	sltu	$1, %0, %1	\n"
+
+	"	lw	%1, 12(%3)	\n"
+	"	addu	%0, $1		\n"
+	"	addu	%0, %1		\n"
+	"	sltu	$1, %0, %1	\n"
+
+	"	addu	%0, $1		# Add final carry\n"
+	"	.set	pop"
+	: "=&r" (sum), "=&r" (tmp)
+	: "r" (saddr), "r" (daddr),
+	  "0" (htonl(len)), "r" (htonl(proto)), "r" (sum));
+
+	return csum_fold(sum);
+}
+
+#include <asm-generic/checksum.h>
+#endif /* CONFIG_GENERIC_CSUM */
+
+#endif /* _ASM_CHECKSUM_H */
diff --git a/arch/mips/include/asm/clocksource.h b/arch/mips/include/asm/clocksource.h
new file mode 100644
index 000000000..2f1ebbea3
--- /dev/null
+++ b/arch/mips/include/asm/clocksource.h
@@ -0,0 +1,11 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2015 Imagination Technologies
+ * Author: Alex Smith <alex.smith@imgtec.com>
+ */
+#ifndef __ASM_CLOCKSOURCE_H
+#define __ASM_CLOCKSOURCE_H
+
+#include <asm/vdso/clocksource.h>
+
+#endif /* __ASM_CLOCKSOURCE_H */
diff --git a/arch/mips/include/asm/cmp.h b/arch/mips/include/asm/cmp.h
new file mode 100644
index 000000000..e9e87504b
--- /dev/null
+++ b/arch/mips/include/asm/cmp.h
@@ -0,0 +1,18 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _ASM_CMP_H
+#define _ASM_CMP_H
+
+/*
+ * Definitions for CMP multitasking on MIPS cores
+ */
+struct task_struct;
+
+extern void cmp_smp_setup(void);
+extern void cmp_smp_finish(void);
+extern void cmp_boot_secondary(int cpu, struct task_struct *t);
+extern void cmp_init_secondary(void);
+extern void cmp_prepare_cpus(unsigned int max_cpus);
+
+/* This is platform specific */
+extern void cmp_send_ipi(int cpu, unsigned int action);
+#endif /*  _ASM_CMP_H */
diff --git a/arch/mips/include/asm/cmpxchg.h b/arch/mips/include/asm/cmpxchg.h
new file mode 100644
index 000000000..7ec9493b2
--- /dev/null
+++ b/arch/mips/include/asm/cmpxchg.h
@@ -0,0 +1,326 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003, 06, 07 by Ralf Baechle (ralf@linux-mips.org)
+ */
+#ifndef __ASM_CMPXCHG_H
+#define __ASM_CMPXCHG_H
+
+#include <linux/bug.h>
+#include <linux/irqflags.h>
+#include <asm/asm.h>
+#include <asm/compiler.h>
+#include <asm/sync.h>
+
+/*
+ * These functions doesn't exist, so if they are called you'll either:
+ *
+ * - Get an error at compile-time due to __compiletime_error, if supported by
+ *   your compiler.
+ *
+ * or:
+ *
+ * - Get an error at link-time due to the call to the missing function.
+ */
+extern unsigned long __cmpxchg_called_with_bad_pointer(void)
+	__compiletime_error("Bad argument size for cmpxchg");
+extern unsigned long __cmpxchg64_unsupported(void)
+	__compiletime_error("cmpxchg64 not available; cpu_has_64bits may be false");
+extern unsigned long __xchg_called_with_bad_pointer(void)
+	__compiletime_error("Bad argument size for xchg");
+
+#define __xchg_asm(ld, st, m, val)					\
+({									\
+	__typeof(*(m)) __ret;						\
+									\
+	if (kernel_uses_llsc) {						\
+		__asm__ __volatile__(					\
+		"	.set	push				\n"	\
+		"	.set	noat				\n"	\
+		"	.set	push				\n"	\
+		"	.set	" MIPS_ISA_ARCH_LEVEL "		\n"	\
+		"	" __SYNC(full, loongson3_war) "		\n"	\
+		"1:	" ld "	%0, %2		# __xchg_asm	\n"	\
+		"	.set	pop				\n"	\
+		"	move	$1, %z3				\n"	\
+		"	.set	" MIPS_ISA_ARCH_LEVEL "		\n"	\
+		"	" st "	$1, %1				\n"	\
+		"\t" __stringify(SC_BEQZ)	"	$1, 1b	\n"	\
+		"	.set	pop				\n"	\
+		: "=&r" (__ret), "=" GCC_OFF_SMALL_ASM() (*m)		\
+		: GCC_OFF_SMALL_ASM() (*m), "Jr" (val)			\
+		: __LLSC_CLOBBER);					\
+	} else {							\
+		unsigned long __flags;					\
+									\
+		raw_local_irq_save(__flags);				\
+		__ret = *m;						\
+		*m = val;						\
+		raw_local_irq_restore(__flags);				\
+	}								\
+									\
+	__ret;								\
+})
+
+extern unsigned long __xchg_small(volatile void *ptr, unsigned long val,
+				  unsigned int size);
+
+static __always_inline
+unsigned long __xchg(volatile void *ptr, unsigned long x, int size)
+{
+	switch (size) {
+	case 1:
+	case 2:
+		return __xchg_small(ptr, x, size);
+
+	case 4:
+		return __xchg_asm("ll", "sc", (volatile u32 *)ptr, x);
+
+	case 8:
+		if (!IS_ENABLED(CONFIG_64BIT))
+			return __xchg_called_with_bad_pointer();
+
+		return __xchg_asm("lld", "scd", (volatile u64 *)ptr, x);
+
+	default:
+		return __xchg_called_with_bad_pointer();
+	}
+}
+
+#define arch_xchg(ptr, x)						\
+({									\
+	__typeof__(*(ptr)) __res;					\
+									\
+	/*								\
+	 * In the Loongson3 workaround case __xchg_asm() already	\
+	 * contains a completion barrier prior to the LL, so we don't	\
+	 * need to emit an extra one here.				\
+	 */								\
+	if (__SYNC_loongson3_war == 0)					\
+		smp_mb__before_llsc();					\
+									\
+	__res = (__typeof__(*(ptr)))					\
+		__xchg((ptr), (unsigned long)(x), sizeof(*(ptr)));	\
+									\
+	smp_llsc_mb();							\
+									\
+	__res;								\
+})
+
+#define __cmpxchg_asm(ld, st, m, old, new)				\
+({									\
+	__typeof(*(m)) __ret;						\
+									\
+	if (kernel_uses_llsc) {						\
+		__asm__ __volatile__(					\
+		"	.set	push				\n"	\
+		"	.set	noat				\n"	\
+		"	.set	push				\n"	\
+		"	.set	"MIPS_ISA_ARCH_LEVEL"		\n"	\
+		"	" __SYNC(full, loongson3_war) "		\n"	\
+		"1:	" ld "	%0, %2		# __cmpxchg_asm \n"	\
+		"	bne	%0, %z3, 2f			\n"	\
+		"	.set	pop				\n"	\
+		"	move	$1, %z4				\n"	\
+		"	.set	"MIPS_ISA_ARCH_LEVEL"		\n"	\
+		"	" st "	$1, %1				\n"	\
+		"\t" __stringify(SC_BEQZ)	"	$1, 1b	\n"	\
+		"	.set	pop				\n"	\
+		"2:	" __SYNC(full, loongson3_war) "		\n"	\
+		: "=&r" (__ret), "=" GCC_OFF_SMALL_ASM() (*m)		\
+		: GCC_OFF_SMALL_ASM() (*m), "Jr" (old), "Jr" (new)	\
+		: __LLSC_CLOBBER);					\
+	} else {							\
+		unsigned long __flags;					\
+									\
+		raw_local_irq_save(__flags);				\
+		__ret = *m;						\
+		if (__ret == old)					\
+			*m = new;					\
+		raw_local_irq_restore(__flags);				\
+	}								\
+									\
+	__ret;								\
+})
+
+extern unsigned long __cmpxchg_small(volatile void *ptr, unsigned long old,
+				     unsigned long new, unsigned int size);
+
+static __always_inline
+unsigned long __cmpxchg(volatile void *ptr, unsigned long old,
+			unsigned long new, unsigned int size)
+{
+	switch (size) {
+	case 1:
+	case 2:
+		return __cmpxchg_small(ptr, old, new, size);
+
+	case 4:
+		return __cmpxchg_asm("ll", "sc", (volatile u32 *)ptr,
+				     (u32)old, new);
+
+	case 8:
+		/* lld/scd are only available for MIPS64 */
+		if (!IS_ENABLED(CONFIG_64BIT))
+			return __cmpxchg_called_with_bad_pointer();
+
+		return __cmpxchg_asm("lld", "scd", (volatile u64 *)ptr,
+				     (u64)old, new);
+
+	default:
+		return __cmpxchg_called_with_bad_pointer();
+	}
+}
+
+#define arch_cmpxchg_local(ptr, old, new)				\
+	((__typeof__(*(ptr)))						\
+		__cmpxchg((ptr),					\
+			  (unsigned long)(__typeof__(*(ptr)))(old),	\
+			  (unsigned long)(__typeof__(*(ptr)))(new),	\
+			  sizeof(*(ptr))))
+
+#define arch_cmpxchg(ptr, old, new)					\
+({									\
+	__typeof__(*(ptr)) __res;					\
+									\
+	/*								\
+	 * In the Loongson3 workaround case __cmpxchg_asm() already	\
+	 * contains a completion barrier prior to the LL, so we don't	\
+	 * need to emit an extra one here.				\
+	 */								\
+	if (__SYNC_loongson3_war == 0)					\
+		smp_mb__before_llsc();					\
+									\
+	__res = arch_cmpxchg_local((ptr), (old), (new));		\
+									\
+	/*								\
+	 * In the Loongson3 workaround case __cmpxchg_asm() already	\
+	 * contains a completion barrier after the SC, so we don't	\
+	 * need to emit an extra one here.				\
+	 */								\
+	if (__SYNC_loongson3_war == 0)					\
+		smp_llsc_mb();						\
+									\
+	__res;								\
+})
+
+#ifdef CONFIG_64BIT
+#define arch_cmpxchg64_local(ptr, o, n)					\
+  ({									\
+	BUILD_BUG_ON(sizeof(*(ptr)) != 8);				\
+	arch_cmpxchg_local((ptr), (o), (n));				\
+  })
+
+#define arch_cmpxchg64(ptr, o, n)					\
+  ({									\
+	BUILD_BUG_ON(sizeof(*(ptr)) != 8);				\
+	arch_cmpxchg((ptr), (o), (n));					\
+  })
+#else
+
+# include <asm-generic/cmpxchg-local.h>
+# define arch_cmpxchg64_local(ptr, o, n) __generic_cmpxchg64_local((ptr), (o), (n))
+
+# ifdef CONFIG_SMP
+
+static inline unsigned long __cmpxchg64(volatile void *ptr,
+					unsigned long long old,
+					unsigned long long new)
+{
+	unsigned long long tmp, ret;
+	unsigned long flags;
+
+	/*
+	 * The assembly below has to combine 32 bit values into a 64 bit
+	 * register, and split 64 bit values from one register into two. If we
+	 * were to take an interrupt in the middle of this we'd only save the
+	 * least significant 32 bits of each register & probably clobber the
+	 * most significant 32 bits of the 64 bit values we're using. In order
+	 * to avoid this we must disable interrupts.
+	 */
+	local_irq_save(flags);
+
+	asm volatile(
+	"	.set	push				\n"
+	"	.set	" MIPS_ISA_ARCH_LEVEL "		\n"
+	/* Load 64 bits from ptr */
+	"	" __SYNC(full, loongson3_war) "		\n"
+	"1:	lld	%L0, %3		# __cmpxchg64	\n"
+	"	.set	pop				\n"
+	/*
+	 * Split the 64 bit value we loaded into the 2 registers that hold the
+	 * ret variable.
+	 */
+	"	dsra	%M0, %L0, 32			\n"
+	"	sll	%L0, %L0, 0			\n"
+	/*
+	 * Compare ret against old, breaking out of the loop if they don't
+	 * match.
+	 */
+	"	bne	%M0, %M4, 2f			\n"
+	"	bne	%L0, %L4, 2f			\n"
+	/*
+	 * Combine the 32 bit halves from the 2 registers that hold the new
+	 * variable into a single 64 bit register.
+	 */
+#  if MIPS_ISA_REV >= 2
+	"	move	%L1, %L5			\n"
+	"	dins	%L1, %M5, 32, 32		\n"
+#  else
+	"	dsll	%L1, %L5, 32			\n"
+	"	dsrl	%L1, %L1, 32			\n"
+	"	.set	noat				\n"
+	"	dsll	$at, %M5, 32			\n"
+	"	or	%L1, %L1, $at			\n"
+	"	.set	at				\n"
+#  endif
+	"	.set	push				\n"
+	"	.set	" MIPS_ISA_ARCH_LEVEL "		\n"
+	/* Attempt to store new at ptr */
+	"	scd	%L1, %2				\n"
+	/* If we failed, loop! */
+	"\t" __stringify(SC_BEQZ) "	%L1, 1b		\n"
+	"2:	" __SYNC(full, loongson3_war) "		\n"
+	"	.set	pop				\n"
+	: "=&r"(ret),
+	  "=&r"(tmp),
+	  "=" GCC_OFF_SMALL_ASM() (*(unsigned long long *)ptr)
+	: GCC_OFF_SMALL_ASM() (*(unsigned long long *)ptr),
+	  "r" (old),
+	  "r" (new)
+	: "memory");
+
+	local_irq_restore(flags);
+	return ret;
+}
+
+#  define arch_cmpxchg64(ptr, o, n) ({					\
+	unsigned long long __old = (__typeof__(*(ptr)))(o);		\
+	unsigned long long __new = (__typeof__(*(ptr)))(n);		\
+	__typeof__(*(ptr)) __res;					\
+									\
+	/*								\
+	 * We can only use cmpxchg64 if we know that the CPU supports	\
+	 * 64-bits, ie. lld & scd. Our call to __cmpxchg64_unsupported	\
+	 * will cause a build error unless cpu_has_64bits is a		\
+	 * compile-time constant 1.					\
+	 */								\
+	if (cpu_has_64bits && kernel_uses_llsc) {			\
+		smp_mb__before_llsc();					\
+		__res = __cmpxchg64((ptr), __old, __new);		\
+		smp_llsc_mb();						\
+	} else {							\
+		__res = __cmpxchg64_unsupported();			\
+	}								\
+									\
+	__res;								\
+})
+
+# else /* !CONFIG_SMP */
+#  define arch_cmpxchg64(ptr, o, n) arch_cmpxchg64_local((ptr), (o), (n))
+# endif /* !CONFIG_SMP */
+#endif /* !CONFIG_64BIT */
+
+#endif /* __ASM_CMPXCHG_H */
diff --git a/arch/mips/include/asm/compat-signal.h b/arch/mips/include/asm/compat-signal.h
new file mode 100644
index 000000000..c3b7a2550
--- /dev/null
+++ b/arch/mips/include/asm/compat-signal.h
@@ -0,0 +1,29 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_COMPAT_SIGNAL_H
+#define __ASM_COMPAT_SIGNAL_H
+
+#include <linux/bug.h>
+#include <linux/compat.h>
+#include <linux/compiler.h>
+
+#include <asm/signal.h>
+#include <asm/siginfo.h>
+
+#include <linux/uaccess.h>
+
+static inline int __copy_conv_sigset_to_user(compat_sigset_t __user *d,
+	const sigset_t *s)
+{
+	BUILD_BUG_ON(sizeof(*d) != sizeof(*s));
+	BUILD_BUG_ON(_NSIG_WORDS != 2);
+
+	return put_compat_sigset(d, s, sizeof(*d));
+}
+
+static inline int __copy_conv_sigset_from_user(sigset_t *d,
+	const compat_sigset_t __user *s)
+{
+	return get_compat_sigset(d, s);
+}
+
+#endif /* __ASM_COMPAT_SIGNAL_H */
diff --git a/arch/mips/include/asm/compat.h b/arch/mips/include/asm/compat.h
new file mode 100644
index 000000000..ec01dc000
--- /dev/null
+++ b/arch/mips/include/asm/compat.h
@@ -0,0 +1,158 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _ASM_COMPAT_H
+#define _ASM_COMPAT_H
+/*
+ * Architecture specific compatibility types
+ */
+#include <linux/thread_info.h>
+#include <linux/types.h>
+#include <asm/page.h>
+#include <asm/ptrace.h>
+
+#define __compat_uid_t	__compat_uid_t
+typedef s32		__compat_uid_t;
+typedef s32		__compat_gid_t;
+
+typedef __compat_uid_t	__compat_uid32_t;
+typedef __compat_gid_t	__compat_gid32_t;
+#define __compat_uid32_t __compat_uid32_t
+
+#define compat_statfs		compat_statfs
+#define compat_ipc64_perm	compat_ipc64_perm
+
+#define _COMPAT_NSIG		128		/* Don't ask !$@#% ...	*/
+#define _COMPAT_NSIG_BPW	32
+typedef u32		compat_sigset_word;
+
+#define COMPAT_RLIM_INFINITY	0x7fffffffUL
+
+#include <asm-generic/compat.h>
+
+#define COMPAT_UTS_MACHINE	"mips\0\0\0"
+
+typedef u32		compat_nlink_t;
+
+struct compat_stat {
+	compat_dev_t	st_dev;
+	s32		st_pad1[3];
+	compat_ino_t	st_ino;
+	compat_mode_t	st_mode;
+	compat_nlink_t	st_nlink;
+	__compat_uid_t	st_uid;
+	__compat_gid_t	st_gid;
+	compat_dev_t	st_rdev;
+	s32		st_pad2[2];
+	compat_off_t	st_size;
+	s32		st_pad3;
+	old_time32_t	st_atime;
+	s32		st_atime_nsec;
+	old_time32_t	st_mtime;
+	s32		st_mtime_nsec;
+	old_time32_t	st_ctime;
+	s32		st_ctime_nsec;
+	s32		st_blksize;
+	s32		st_blocks;
+	s32		st_pad4[14];
+};
+
+#define __ARCH_COMPAT_FLOCK_EXTRA_SYSID		s32 l_sysid;
+#define __ARCH_COMPAT_FLOCK_PAD			s32 pad[4];
+
+struct compat_statfs {
+	int		f_type;
+	int		f_bsize;
+	int		f_frsize;
+	int		f_blocks;
+	int		f_bfree;
+	int		f_files;
+	int		f_ffree;
+	int		f_bavail;
+	compat_fsid_t	f_fsid;
+	int		f_namelen;
+	int		f_flags;
+	int		f_spare[5];
+};
+
+struct compat_ipc64_perm {
+	compat_key_t key;
+	__compat_uid32_t uid;
+	__compat_gid32_t gid;
+	__compat_uid32_t cuid;
+	__compat_gid32_t cgid;
+	compat_mode_t mode;
+	unsigned short seq;
+	unsigned short __pad2;
+	compat_ulong_t __unused1;
+	compat_ulong_t __unused2;
+};
+
+struct compat_semid64_ds {
+	struct compat_ipc64_perm sem_perm;
+	compat_ulong_t	sem_otime;
+	compat_ulong_t	sem_ctime;
+	compat_ulong_t	sem_nsems;
+	compat_ulong_t	sem_otime_high;
+	compat_ulong_t	sem_ctime_high;
+};
+
+struct compat_msqid64_ds {
+	struct compat_ipc64_perm msg_perm;
+#ifndef CONFIG_CPU_LITTLE_ENDIAN
+	compat_ulong_t	msg_stime_high;
+#endif
+	compat_ulong_t	msg_stime;
+#ifdef CONFIG_CPU_LITTLE_ENDIAN
+	compat_ulong_t	msg_stime_high;
+#endif
+#ifndef CONFIG_CPU_LITTLE_ENDIAN
+	compat_ulong_t	msg_rtime_high;
+#endif
+	compat_ulong_t	msg_rtime;
+#ifdef CONFIG_CPU_LITTLE_ENDIAN
+	compat_ulong_t	msg_rtime_high;
+#endif
+#ifndef CONFIG_CPU_LITTLE_ENDIAN
+	compat_ulong_t	msg_ctime_high;
+#endif
+	compat_ulong_t	msg_ctime;
+#ifdef CONFIG_CPU_LITTLE_ENDIAN
+	compat_ulong_t	msg_ctime_high;
+#endif
+	compat_ulong_t	msg_cbytes;
+	compat_ulong_t	msg_qnum;
+	compat_ulong_t	msg_qbytes;
+	compat_pid_t	msg_lspid;
+	compat_pid_t	msg_lrpid;
+	compat_ulong_t	__unused4;
+	compat_ulong_t	__unused5;
+};
+
+struct compat_shmid64_ds {
+	struct compat_ipc64_perm shm_perm;
+	compat_size_t	shm_segsz;
+	compat_ulong_t	shm_atime;
+	compat_ulong_t	shm_dtime;
+	compat_ulong_t	shm_ctime;
+	compat_pid_t	shm_cpid;
+	compat_pid_t	shm_lpid;
+	compat_ulong_t	shm_nattch;
+	compat_ushort_t	shm_atime_high;
+	compat_ushort_t	shm_dtime_high;
+	compat_ushort_t	shm_ctime_high;
+	compat_ushort_t	__unused2;
+};
+
+/* MIPS has unusual order of fields in stack_t */
+typedef struct compat_sigaltstack {
+	compat_uptr_t			ss_sp;
+	compat_size_t			ss_size;
+	int				ss_flags;
+} compat_stack_t;
+#define compat_sigaltstack compat_sigaltstack
+
+static inline int is_compat_task(void)
+{
+	return test_thread_flag(TIF_32BIT_ADDR);
+}
+
+#endif /* _ASM_COMPAT_H */
diff --git a/arch/mips/include/asm/compiler.h b/arch/mips/include/asm/compiler.h
new file mode 100644
index 000000000..2b06090a7
--- /dev/null
+++ b/arch/mips/include/asm/compiler.h
@@ -0,0 +1,66 @@
+/*
+ * Copyright (C) 2004, 2007  Maciej W. Rozycki
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#ifndef _ASM_COMPILER_H
+#define _ASM_COMPILER_H
+
+/*
+ * With GCC 4.5 onwards we can use __builtin_unreachable to indicate to the
+ * compiler that a particular code path will never be hit. This allows it to be
+ * optimised out of the generated binary.
+ *
+ * Unfortunately at least GCC 4.6.3 through 7.3.0 inclusive suffer from a bug
+ * that can lead to instructions from beyond an unreachable statement being
+ * incorrectly reordered into earlier delay slots if the unreachable statement
+ * is the only content of a case in a switch statement. This can lead to
+ * seemingly random behaviour, such as invalid memory accesses from incorrectly
+ * reordered loads or stores. See this potential GCC fix for details:
+ *
+ *   https://gcc.gnu.org/ml/gcc-patches/2015-09/msg00360.html
+ *
+ * It is unclear whether GCC 8 onwards suffer from the same issue - nothing
+ * relevant is mentioned in GCC 8 release notes and nothing obviously relevant
+ * stands out in GCC commit logs, but these newer GCC versions generate very
+ * different code for the testcase which doesn't exhibit the bug.
+ *
+ * GCC also handles stack allocation suboptimally when calling noreturn
+ * functions or calling __builtin_unreachable():
+ *
+ *   https://gcc.gnu.org/bugzilla/show_bug.cgi?id=82365
+ *
+ * We work around both of these issues by placing a volatile asm statement,
+ * which GCC is prevented from reordering past, prior to __builtin_unreachable
+ * calls.
+ *
+ * The .insn statement is required to ensure that any branches to the
+ * statement, which sadly must be kept due to the asm statement, are known to
+ * be branches to code and satisfy linker requirements for microMIPS kernels.
+ */
+#undef barrier_before_unreachable
+#define barrier_before_unreachable() asm volatile(".insn")
+
+#define GCC_OFF_SMALL_ASM() "ZC"
+
+#ifdef CONFIG_CPU_MIPSR6
+#define MIPS_ISA_LEVEL "mips64r6"
+#define MIPS_ISA_ARCH_LEVEL MIPS_ISA_LEVEL
+#define MIPS_ISA_LEVEL_RAW mips64r6
+#define MIPS_ISA_ARCH_LEVEL_RAW MIPS_ISA_LEVEL_RAW
+#elif defined(CONFIG_CPU_MIPSR5)
+#define MIPS_ISA_LEVEL "mips64r5"
+#define MIPS_ISA_ARCH_LEVEL MIPS_ISA_LEVEL
+#define MIPS_ISA_LEVEL_RAW mips64r5
+#define MIPS_ISA_ARCH_LEVEL_RAW MIPS_ISA_LEVEL_RAW
+#else
+/* MIPS64 is a superset of MIPS32 */
+#define MIPS_ISA_LEVEL "mips64r2"
+#define MIPS_ISA_ARCH_LEVEL "arch=r4000"
+#define MIPS_ISA_LEVEL_RAW mips64r2
+#define MIPS_ISA_ARCH_LEVEL_RAW MIPS_ISA_LEVEL_RAW
+#endif /* CONFIG_CPU_MIPSR6 */
+
+#endif /* _ASM_COMPILER_H */
diff --git a/arch/mips/include/asm/cop2.h b/arch/mips/include/asm/cop2.h
new file mode 100644
index 000000000..01b05be23
--- /dev/null
+++ b/arch/mips/include/asm/cop2.h
@@ -0,0 +1,61 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2009 Wind River Systems,
+ *   written by Ralf Baechle <ralf@linux-mips.org>
+ */
+#ifndef __ASM_COP2_H
+#define __ASM_COP2_H
+
+#include <linux/notifier.h>
+
+#if defined(CONFIG_CPU_CAVIUM_OCTEON)
+
+extern void octeon_cop2_save(struct octeon_cop2_state *);
+extern void octeon_cop2_restore(struct octeon_cop2_state *);
+
+#define cop2_save(r)		octeon_cop2_save(&(r)->thread.cp2)
+#define cop2_restore(r)		octeon_cop2_restore(&(r)->thread.cp2)
+
+#define cop2_present		1
+#define cop2_lazy_restore	1
+
+#elif defined(CONFIG_CPU_LOONGSON64)
+
+#define cop2_present		1
+#define cop2_lazy_restore	1
+#define cop2_save(r)		do { (void)(r); } while (0)
+#define cop2_restore(r)		do { (void)(r); } while (0)
+
+#else
+
+#define cop2_present		0
+#define cop2_lazy_restore	0
+#define cop2_save(r)		do { (void)(r); } while (0)
+#define cop2_restore(r)		do { (void)(r); } while (0)
+#endif
+
+enum cu2_ops {
+	CU2_EXCEPTION,
+	CU2_LWC2_OP,
+	CU2_LDC2_OP,
+	CU2_SWC2_OP,
+	CU2_SDC2_OP,
+};
+
+extern int register_cu2_notifier(struct notifier_block *nb);
+extern int cu2_notifier_call_chain(unsigned long val, void *v);
+
+#define cu2_notifier(fn, pri)						\
+({									\
+	static struct notifier_block fn##_nb = {			\
+		.notifier_call = fn,					\
+		.priority = pri						\
+	};								\
+									\
+	register_cu2_notifier(&fn##_nb);				\
+})
+
+#endif /* __ASM_COP2_H */
diff --git a/arch/mips/include/asm/cpu-features.h b/arch/mips/include/asm/cpu-features.h
new file mode 100644
index 000000000..e0a4da4cf
--- /dev/null
+++ b/arch/mips/include/asm/cpu-features.h
@@ -0,0 +1,754 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003, 2004 Ralf Baechle
+ * Copyright (C) 2004  Maciej W. Rozycki
+ */
+#ifndef __ASM_CPU_FEATURES_H
+#define __ASM_CPU_FEATURES_H
+
+#include <asm/cpu.h>
+#include <asm/cpu-info.h>
+#include <asm/isa-rev.h>
+#include <cpu-feature-overrides.h>
+
+#define __ase(ase)			(cpu_data[0].ases & (ase))
+#define __isa(isa)			(cpu_data[0].isa_level & (isa))
+#define __opt(opt)			(cpu_data[0].options & (opt))
+
+/*
+ * Check if MIPS_ISA_REV is >= isa *and* an option or ASE is detected during
+ * boot (typically by cpu_probe()).
+ *
+ * Note that these should only be used in cases where a kernel built for an
+ * older ISA *cannot* run on a CPU which supports the feature in question. For
+ * example this may be used for features introduced with MIPSr6, since a kernel
+ * built for an older ISA cannot run on a MIPSr6 CPU. This should not be used
+ * for MIPSr2 features however, since a MIPSr1 or earlier kernel might run on a
+ * MIPSr2 CPU.
+ */
+#define __isa_ge_and_ase(isa, ase)	((MIPS_ISA_REV >= (isa)) && __ase(ase))
+#define __isa_ge_and_opt(isa, opt)	((MIPS_ISA_REV >= (isa)) && __opt(opt))
+
+/*
+ * Check if MIPS_ISA_REV is >= isa *or* an option or ASE is detected during
+ * boot (typically by cpu_probe()).
+ *
+ * These are for use with features that are optional up until a particular ISA
+ * revision & then become required.
+ */
+#define __isa_ge_or_ase(isa, ase)	((MIPS_ISA_REV >= (isa)) || __ase(ase))
+#define __isa_ge_or_opt(isa, opt)	((MIPS_ISA_REV >= (isa)) || __opt(opt))
+
+/*
+ * Check if MIPS_ISA_REV is < isa *and* an option or ASE is detected during
+ * boot (typically by cpu_probe()).
+ *
+ * These are for use with features that are optional up until a particular ISA
+ * revision & are then removed - ie. no longer present in any CPU implementing
+ * the given ISA revision.
+ */
+#define __isa_lt_and_ase(isa, ase)	((MIPS_ISA_REV < (isa)) && __ase(ase))
+#define __isa_lt_and_opt(isa, opt)	((MIPS_ISA_REV < (isa)) && __opt(opt))
+
+/*
+ * Similarly allow for ISA level checks that take into account knowledge of the
+ * ISA targeted by the kernel build, provided by MIPS_ISA_REV.
+ */
+#define __isa_ge_and_flag(isa, flag)	((MIPS_ISA_REV >= (isa)) && __isa(flag))
+#define __isa_ge_or_flag(isa, flag)	((MIPS_ISA_REV >= (isa)) || __isa(flag))
+#define __isa_lt_and_flag(isa, flag)	((MIPS_ISA_REV < (isa)) && __isa(flag))
+#define __isa_range(ge, lt) \
+	((MIPS_ISA_REV >= (ge)) && (MIPS_ISA_REV < (lt)))
+#define __isa_range_or_flag(ge, lt, flag) \
+	(__isa_range(ge, lt) || ((MIPS_ISA_REV < (lt)) && __isa(flag)))
+#define __isa_range_and_ase(ge, lt, ase) \
+	(__isa_range(ge, lt) && __ase(ase))
+
+/*
+ * SMP assumption: Options of CPU 0 are a superset of all processors.
+ * This is true for all known MIPS systems.
+ */
+#ifndef cpu_has_tlb
+#define cpu_has_tlb		__opt(MIPS_CPU_TLB)
+#endif
+#ifndef cpu_has_ftlb
+#define cpu_has_ftlb		__opt(MIPS_CPU_FTLB)
+#endif
+#ifndef cpu_has_tlbinv
+#define cpu_has_tlbinv		__opt(MIPS_CPU_TLBINV)
+#endif
+#ifndef cpu_has_segments
+#define cpu_has_segments	__opt(MIPS_CPU_SEGMENTS)
+#endif
+#ifndef cpu_has_eva
+#define cpu_has_eva		__opt(MIPS_CPU_EVA)
+#endif
+#ifndef cpu_has_htw
+#define cpu_has_htw		__opt(MIPS_CPU_HTW)
+#endif
+#ifndef cpu_has_ldpte
+#define cpu_has_ldpte		__opt(MIPS_CPU_LDPTE)
+#endif
+#ifndef cpu_has_rixiex
+#define cpu_has_rixiex		__isa_ge_or_opt(6, MIPS_CPU_RIXIEX)
+#endif
+#ifndef cpu_has_maar
+#define cpu_has_maar		__opt(MIPS_CPU_MAAR)
+#endif
+#ifndef cpu_has_rw_llb
+#define cpu_has_rw_llb		__isa_ge_or_opt(6, MIPS_CPU_RW_LLB)
+#endif
+
+/*
+ * For the moment we don't consider R6000 and R8000 so we can assume that
+ * anything that doesn't support R4000-style exceptions and interrupts is
+ * R3000-like.  Users should still treat these two macro definitions as
+ * opaque.
+ */
+#ifndef cpu_has_3kex
+#define cpu_has_3kex		(!cpu_has_4kex)
+#endif
+#ifndef cpu_has_4kex
+#define cpu_has_4kex		__isa_ge_or_opt(1, MIPS_CPU_4KEX)
+#endif
+#ifndef cpu_has_3k_cache
+#define cpu_has_3k_cache	__isa_lt_and_opt(1, MIPS_CPU_3K_CACHE)
+#endif
+#ifndef cpu_has_4k_cache
+#define cpu_has_4k_cache	__isa_ge_or_opt(1, MIPS_CPU_4K_CACHE)
+#endif
+#ifndef cpu_has_octeon_cache
+#define cpu_has_octeon_cache						\
+({									\
+	int __res;							\
+									\
+	switch (boot_cpu_type()) {					\
+	case CPU_CAVIUM_OCTEON:						\
+	case CPU_CAVIUM_OCTEON_PLUS:					\
+	case CPU_CAVIUM_OCTEON2:					\
+	case CPU_CAVIUM_OCTEON3:					\
+		__res = 1;						\
+		break;							\
+									\
+	default:							\
+		__res = 0;						\
+	}								\
+									\
+	__res;								\
+})
+#endif
+/* Don't override `cpu_has_fpu' to 1 or the "nofpu" option won't work.  */
+#ifndef cpu_has_fpu
+# ifdef CONFIG_MIPS_FP_SUPPORT
+#  define cpu_has_fpu		(current_cpu_data.options & MIPS_CPU_FPU)
+#  define raw_cpu_has_fpu	(raw_current_cpu_data.options & MIPS_CPU_FPU)
+# else
+#  define cpu_has_fpu		0
+#  define raw_cpu_has_fpu	0
+# endif
+#else
+# if cpu_has_fpu
+#  error "Forcing `cpu_has_fpu' to non-zero is not supported"
+# endif
+# define raw_cpu_has_fpu	cpu_has_fpu
+#endif
+#ifndef cpu_has_32fpr
+#define cpu_has_32fpr		__isa_ge_or_opt(1, MIPS_CPU_32FPR)
+#endif
+#ifndef cpu_has_counter
+#define cpu_has_counter		__opt(MIPS_CPU_COUNTER)
+#endif
+#ifndef cpu_has_watch
+#define cpu_has_watch		__opt(MIPS_CPU_WATCH)
+#endif
+#ifndef cpu_has_divec
+#define cpu_has_divec		__isa_ge_or_opt(1, MIPS_CPU_DIVEC)
+#endif
+#ifndef cpu_has_vce
+#define cpu_has_vce		__opt(MIPS_CPU_VCE)
+#endif
+#ifndef cpu_has_cache_cdex_p
+#define cpu_has_cache_cdex_p	__opt(MIPS_CPU_CACHE_CDEX_P)
+#endif
+#ifndef cpu_has_cache_cdex_s
+#define cpu_has_cache_cdex_s	__opt(MIPS_CPU_CACHE_CDEX_S)
+#endif
+#ifndef cpu_has_prefetch
+#define cpu_has_prefetch	__isa_ge_or_opt(1, MIPS_CPU_PREFETCH)
+#endif
+#ifndef cpu_has_mcheck
+#define cpu_has_mcheck		__isa_ge_or_opt(1, MIPS_CPU_MCHECK)
+#endif
+#ifndef cpu_has_ejtag
+#define cpu_has_ejtag		__opt(MIPS_CPU_EJTAG)
+#endif
+#ifndef cpu_has_llsc
+#define cpu_has_llsc		__isa_ge_or_opt(1, MIPS_CPU_LLSC)
+#endif
+#ifndef kernel_uses_llsc
+#define kernel_uses_llsc	cpu_has_llsc
+#endif
+#ifndef cpu_has_guestctl0ext
+#define cpu_has_guestctl0ext	__opt(MIPS_CPU_GUESTCTL0EXT)
+#endif
+#ifndef cpu_has_guestctl1
+#define cpu_has_guestctl1	__opt(MIPS_CPU_GUESTCTL1)
+#endif
+#ifndef cpu_has_guestctl2
+#define cpu_has_guestctl2	__opt(MIPS_CPU_GUESTCTL2)
+#endif
+#ifndef cpu_has_guestid
+#define cpu_has_guestid		__opt(MIPS_CPU_GUESTID)
+#endif
+#ifndef cpu_has_drg
+#define cpu_has_drg		__opt(MIPS_CPU_DRG)
+#endif
+#ifndef cpu_has_mips16
+#define cpu_has_mips16		__isa_lt_and_ase(6, MIPS_ASE_MIPS16)
+#endif
+#ifndef cpu_has_mips16e2
+#define cpu_has_mips16e2	__isa_lt_and_ase(6, MIPS_ASE_MIPS16E2)
+#endif
+#ifndef cpu_has_mdmx
+#define cpu_has_mdmx		__isa_lt_and_ase(6, MIPS_ASE_MDMX)
+#endif
+#ifndef cpu_has_mips3d
+#define cpu_has_mips3d		__isa_lt_and_ase(6, MIPS_ASE_MIPS3D)
+#endif
+#ifndef cpu_has_smartmips
+#define cpu_has_smartmips	__isa_lt_and_ase(6, MIPS_ASE_SMARTMIPS)
+#endif
+
+#ifndef cpu_has_rixi
+#define cpu_has_rixi		__isa_ge_or_opt(6, MIPS_CPU_RIXI)
+#endif
+
+#ifndef cpu_has_mmips
+# if defined(__mips_micromips)
+#  define cpu_has_mmips		1
+# elif defined(CONFIG_SYS_SUPPORTS_MICROMIPS)
+#  define cpu_has_mmips		__opt(MIPS_CPU_MICROMIPS)
+# else
+#  define cpu_has_mmips		0
+# endif
+#endif
+
+#ifndef cpu_has_lpa
+#define cpu_has_lpa		__opt(MIPS_CPU_LPA)
+#endif
+#ifndef cpu_has_mvh
+#define cpu_has_mvh		__opt(MIPS_CPU_MVH)
+#endif
+#ifndef cpu_has_xpa
+#define cpu_has_xpa		(cpu_has_lpa && cpu_has_mvh)
+#endif
+#ifndef cpu_has_vtag_icache
+#define cpu_has_vtag_icache	(cpu_data[0].icache.flags & MIPS_CACHE_VTAG)
+#endif
+#ifndef cpu_has_dc_aliases
+#define cpu_has_dc_aliases	(cpu_data[0].dcache.flags & MIPS_CACHE_ALIASES)
+#endif
+#ifndef cpu_has_ic_fills_f_dc
+#define cpu_has_ic_fills_f_dc	(cpu_data[0].icache.flags & MIPS_CACHE_IC_F_DC)
+#endif
+#ifndef cpu_has_pindexed_dcache
+#define cpu_has_pindexed_dcache	(cpu_data[0].dcache.flags & MIPS_CACHE_PINDEX)
+#endif
+
+/*
+ * I-Cache snoops remote store.	 This only matters on SMP.  Some multiprocessors
+ * such as the R10000 have I-Caches that snoop local stores; the embedded ones
+ * don't.  For maintaining I-cache coherency this means we need to flush the
+ * D-cache all the way back to whever the I-cache does refills from, so the
+ * I-cache has a chance to see the new data at all.  Then we have to flush the
+ * I-cache also.
+ * Note we may have been rescheduled and may no longer be running on the CPU
+ * that did the store so we can't optimize this into only doing the flush on
+ * the local CPU.
+ */
+#ifndef cpu_icache_snoops_remote_store
+#ifdef CONFIG_SMP
+#define cpu_icache_snoops_remote_store	(cpu_data[0].icache.flags & MIPS_IC_SNOOPS_REMOTE)
+#else
+#define cpu_icache_snoops_remote_store	1
+#endif
+#endif
+
+#ifndef cpu_has_mips_1
+# define cpu_has_mips_1		(MIPS_ISA_REV < 6)
+#endif
+#ifndef cpu_has_mips_2
+# define cpu_has_mips_2		__isa_lt_and_flag(6, MIPS_CPU_ISA_II)
+#endif
+#ifndef cpu_has_mips_3
+# define cpu_has_mips_3		__isa_lt_and_flag(6, MIPS_CPU_ISA_III)
+#endif
+#ifndef cpu_has_mips_4
+# define cpu_has_mips_4		__isa_lt_and_flag(6, MIPS_CPU_ISA_IV)
+#endif
+#ifndef cpu_has_mips_5
+# define cpu_has_mips_5		__isa_lt_and_flag(6, MIPS_CPU_ISA_V)
+#endif
+#ifndef cpu_has_mips32r1
+# define cpu_has_mips32r1	__isa_range_or_flag(1, 6, MIPS_CPU_ISA_M32R1)
+#endif
+#ifndef cpu_has_mips32r2
+# define cpu_has_mips32r2	__isa_range_or_flag(2, 6, MIPS_CPU_ISA_M32R2)
+#endif
+#ifndef cpu_has_mips32r5
+# define cpu_has_mips32r5	__isa_range_or_flag(5, 6, MIPS_CPU_ISA_M32R5)
+#endif
+#ifndef cpu_has_mips32r6
+# define cpu_has_mips32r6	__isa_ge_or_flag(6, MIPS_CPU_ISA_M32R6)
+#endif
+#ifndef cpu_has_mips64r1
+# define cpu_has_mips64r1	(cpu_has_64bits && \
+				 __isa_range_or_flag(1, 6, MIPS_CPU_ISA_M64R1))
+#endif
+#ifndef cpu_has_mips64r2
+# define cpu_has_mips64r2	(cpu_has_64bits && \
+				 __isa_range_or_flag(2, 6, MIPS_CPU_ISA_M64R2))
+#endif
+#ifndef cpu_has_mips64r5
+# define cpu_has_mips64r5	(cpu_has_64bits && \
+				 __isa_range_or_flag(5, 6, MIPS_CPU_ISA_M64R5))
+#endif
+#ifndef cpu_has_mips64r6
+# define cpu_has_mips64r6	__isa_ge_and_flag(6, MIPS_CPU_ISA_M64R6)
+#endif
+
+/*
+ * Shortcuts ...
+ */
+#define cpu_has_mips_2_3_4_5	(cpu_has_mips_2 | cpu_has_mips_3_4_5)
+#define cpu_has_mips_3_4_5	(cpu_has_mips_3 | cpu_has_mips_4_5)
+#define cpu_has_mips_4_5	(cpu_has_mips_4 | cpu_has_mips_5)
+
+#define cpu_has_mips_2_3_4_5_r	(cpu_has_mips_2 | cpu_has_mips_3_4_5_r)
+#define cpu_has_mips_3_4_5_r	(cpu_has_mips_3 | cpu_has_mips_4_5_r)
+#define cpu_has_mips_4_5_r	(cpu_has_mips_4 | cpu_has_mips_5_r)
+#define cpu_has_mips_5_r	(cpu_has_mips_5 | cpu_has_mips_r)
+
+#define cpu_has_mips_3_4_5_64_r2_r6					\
+				(cpu_has_mips_3 | cpu_has_mips_4_5_64_r2_r6)
+#define cpu_has_mips_4_5_64_r2_r6					\
+				(cpu_has_mips_4_5 | cpu_has_mips64r1 |	\
+				 cpu_has_mips_r2 | cpu_has_mips_r5 | \
+				 cpu_has_mips_r6)
+
+#define cpu_has_mips32	(cpu_has_mips32r1 | cpu_has_mips32r2 | \
+			 cpu_has_mips32r5 | cpu_has_mips32r6)
+#define cpu_has_mips64	(cpu_has_mips64r1 | cpu_has_mips64r2 | \
+			 cpu_has_mips64r5 | cpu_has_mips64r6)
+#define cpu_has_mips_r1 (cpu_has_mips32r1 | cpu_has_mips64r1)
+#define cpu_has_mips_r2 (cpu_has_mips32r2 | cpu_has_mips64r2)
+#define cpu_has_mips_r5	(cpu_has_mips32r5 | cpu_has_mips64r5)
+#define cpu_has_mips_r6	(cpu_has_mips32r6 | cpu_has_mips64r6)
+#define cpu_has_mips_r	(cpu_has_mips32r1 | cpu_has_mips32r2 | \
+			 cpu_has_mips32r5 | cpu_has_mips32r6 | \
+			 cpu_has_mips64r1 | cpu_has_mips64r2 | \
+			 cpu_has_mips64r5 | cpu_has_mips64r6)
+
+/* MIPSR2 - MIPSR6 have a lot of similarities */
+#define cpu_has_mips_r2_r6	(cpu_has_mips_r2 | cpu_has_mips_r5 | \
+				 cpu_has_mips_r6)
+
+/*
+ * cpu_has_mips_r2_exec_hazard - return if IHB is required on current processor
+ *
+ * Returns non-zero value if the current processor implementation requires
+ * an IHB instruction to deal with an instruction hazard as per MIPS R2
+ * architecture specification, zero otherwise.
+ */
+#ifndef cpu_has_mips_r2_exec_hazard
+#define cpu_has_mips_r2_exec_hazard					\
+({									\
+	int __res;							\
+									\
+	switch (boot_cpu_type()) {					\
+	case CPU_M14KC:							\
+	case CPU_74K:							\
+	case CPU_1074K:							\
+	case CPU_PROAPTIV:						\
+	case CPU_P5600:							\
+	case CPU_M5150:							\
+	case CPU_QEMU_GENERIC:						\
+	case CPU_CAVIUM_OCTEON:						\
+	case CPU_CAVIUM_OCTEON_PLUS:					\
+	case CPU_CAVIUM_OCTEON2:					\
+	case CPU_CAVIUM_OCTEON3:					\
+		__res = 0;						\
+		break;							\
+									\
+	default:							\
+		__res = 1;						\
+	}								\
+									\
+	__res;								\
+})
+#endif
+
+/*
+ * MIPS32, MIPS64, VR5500, IDT32332, IDT32334 and maybe a few other
+ * pre-MIPS32/MIPS64 processors have CLO, CLZ.	The IDT RC64574 is 64-bit and
+ * has CLO and CLZ but not DCLO nor DCLZ.  For 64-bit kernels
+ * cpu_has_clo_clz also indicates the availability of DCLO and DCLZ.
+ */
+#ifndef cpu_has_clo_clz
+#define cpu_has_clo_clz	cpu_has_mips_r
+#endif
+
+/*
+ * MIPS32 R2, MIPS64 R2, Loongson 3A and Octeon have WSBH.
+ * MIPS64 R2, Loongson 3A and Octeon have WSBH, DSBH and DSHD.
+ * This indicates the availability of WSBH and in case of 64 bit CPUs also
+ * DSBH and DSHD.
+ */
+#ifndef cpu_has_wsbh
+#define cpu_has_wsbh		cpu_has_mips_r2
+#endif
+
+#ifndef cpu_has_dsp
+#define cpu_has_dsp		__ase(MIPS_ASE_DSP)
+#endif
+
+#ifndef cpu_has_dsp2
+#define cpu_has_dsp2		__ase(MIPS_ASE_DSP2P)
+#endif
+
+#ifndef cpu_has_dsp3
+#define cpu_has_dsp3		__ase(MIPS_ASE_DSP3)
+#endif
+
+#ifndef cpu_has_loongson_mmi
+#define cpu_has_loongson_mmi		__ase(MIPS_ASE_LOONGSON_MMI)
+#endif
+
+#ifndef cpu_has_loongson_cam
+#define cpu_has_loongson_cam		__ase(MIPS_ASE_LOONGSON_CAM)
+#endif
+
+#ifndef cpu_has_loongson_ext
+#define cpu_has_loongson_ext		__ase(MIPS_ASE_LOONGSON_EXT)
+#endif
+
+#ifndef cpu_has_loongson_ext2
+#define cpu_has_loongson_ext2		__ase(MIPS_ASE_LOONGSON_EXT2)
+#endif
+
+#ifndef cpu_has_mipsmt
+#define cpu_has_mipsmt		__isa_range_and_ase(2, 6, MIPS_ASE_MIPSMT)
+#endif
+
+#ifndef cpu_has_vp
+#define cpu_has_vp		__isa_ge_and_opt(6, MIPS_CPU_VP)
+#endif
+
+#ifndef cpu_has_userlocal
+#define cpu_has_userlocal	__isa_ge_or_opt(6, MIPS_CPU_ULRI)
+#endif
+
+#ifdef CONFIG_32BIT
+# ifndef cpu_has_nofpuex
+# define cpu_has_nofpuex	__isa_lt_and_opt(1, MIPS_CPU_NOFPUEX)
+# endif
+# ifndef cpu_has_64bits
+# define cpu_has_64bits		(cpu_data[0].isa_level & MIPS_CPU_ISA_64BIT)
+# endif
+# ifndef cpu_has_64bit_zero_reg
+# define cpu_has_64bit_zero_reg	(cpu_data[0].isa_level & MIPS_CPU_ISA_64BIT)
+# endif
+# ifndef cpu_has_64bit_gp_regs
+# define cpu_has_64bit_gp_regs		0
+# endif
+# ifndef cpu_vmbits
+# define cpu_vmbits 31
+# endif
+#endif
+
+#ifdef CONFIG_64BIT
+# ifndef cpu_has_nofpuex
+# define cpu_has_nofpuex		0
+# endif
+# ifndef cpu_has_64bits
+# define cpu_has_64bits			1
+# endif
+# ifndef cpu_has_64bit_zero_reg
+# define cpu_has_64bit_zero_reg		1
+# endif
+# ifndef cpu_has_64bit_gp_regs
+# define cpu_has_64bit_gp_regs		1
+# endif
+# ifndef cpu_vmbits
+# define cpu_vmbits cpu_data[0].vmbits
+# define __NEED_VMBITS_PROBE
+# endif
+#endif
+
+#if defined(CONFIG_CPU_MIPSR2_IRQ_VI) && !defined(cpu_has_vint)
+# define cpu_has_vint		__opt(MIPS_CPU_VINT)
+#elif !defined(cpu_has_vint)
+# define cpu_has_vint			0
+#endif
+
+#if defined(CONFIG_CPU_MIPSR2_IRQ_EI) && !defined(cpu_has_veic)
+# define cpu_has_veic		__opt(MIPS_CPU_VEIC)
+#elif !defined(cpu_has_veic)
+# define cpu_has_veic			0
+#endif
+
+#ifndef cpu_has_inclusive_pcaches
+#define cpu_has_inclusive_pcaches	__opt(MIPS_CPU_INCLUSIVE_CACHES)
+#endif
+
+#ifndef cpu_dcache_line_size
+#define cpu_dcache_line_size()	cpu_data[0].dcache.linesz
+#endif
+#ifndef cpu_icache_line_size
+#define cpu_icache_line_size()	cpu_data[0].icache.linesz
+#endif
+#ifndef cpu_scache_line_size
+#define cpu_scache_line_size()	cpu_data[0].scache.linesz
+#endif
+#ifndef cpu_tcache_line_size
+#define cpu_tcache_line_size()	cpu_data[0].tcache.linesz
+#endif
+
+#ifndef cpu_hwrena_impl_bits
+#define cpu_hwrena_impl_bits		0
+#endif
+
+#ifndef cpu_has_perf_cntr_intr_bit
+#define cpu_has_perf_cntr_intr_bit	__opt(MIPS_CPU_PCI)
+#endif
+
+#ifndef cpu_has_vz
+#define cpu_has_vz		__ase(MIPS_ASE_VZ)
+#endif
+
+#if defined(CONFIG_CPU_HAS_MSA) && !defined(cpu_has_msa)
+# define cpu_has_msa		__ase(MIPS_ASE_MSA)
+#elif !defined(cpu_has_msa)
+# define cpu_has_msa		0
+#endif
+
+#ifndef cpu_has_ufr
+# define cpu_has_ufr		__opt(MIPS_CPU_UFR)
+#endif
+
+#ifndef cpu_has_fre
+# define cpu_has_fre		__opt(MIPS_CPU_FRE)
+#endif
+
+#ifndef cpu_has_cdmm
+# define cpu_has_cdmm		__opt(MIPS_CPU_CDMM)
+#endif
+
+#ifndef cpu_has_small_pages
+# define cpu_has_small_pages	__opt(MIPS_CPU_SP)
+#endif
+
+#ifndef cpu_has_nan_legacy
+#define cpu_has_nan_legacy	__isa_lt_and_opt(6, MIPS_CPU_NAN_LEGACY)
+#endif
+#ifndef cpu_has_nan_2008
+#define cpu_has_nan_2008	__isa_ge_or_opt(6, MIPS_CPU_NAN_2008)
+#endif
+
+#ifndef cpu_has_ebase_wg
+# define cpu_has_ebase_wg	__opt(MIPS_CPU_EBASE_WG)
+#endif
+
+#ifndef cpu_has_badinstr
+# define cpu_has_badinstr	__isa_ge_or_opt(6, MIPS_CPU_BADINSTR)
+#endif
+
+#ifndef cpu_has_badinstrp
+# define cpu_has_badinstrp	__isa_ge_or_opt(6, MIPS_CPU_BADINSTRP)
+#endif
+
+#ifndef cpu_has_contextconfig
+# define cpu_has_contextconfig	__opt(MIPS_CPU_CTXTC)
+#endif
+
+#ifndef cpu_has_perf
+# define cpu_has_perf		__opt(MIPS_CPU_PERF)
+#endif
+
+#ifndef cpu_has_mac2008_only
+# define cpu_has_mac2008_only	__opt(MIPS_CPU_MAC_2008_ONLY)
+#endif
+
+#ifndef cpu_has_ftlbparex
+# define cpu_has_ftlbparex	__opt(MIPS_CPU_FTLBPAREX)
+#endif
+
+#ifndef cpu_has_gsexcex
+# define cpu_has_gsexcex	__opt(MIPS_CPU_GSEXCEX)
+#endif
+
+#ifdef CONFIG_SMP
+/*
+ * Some systems share FTLB RAMs between threads within a core (siblings in
+ * kernel parlance). This means that FTLB entries may become invalid at almost
+ * any point when an entry is evicted due to a sibling thread writing an entry
+ * to the shared FTLB RAM.
+ *
+ * This is only relevant to SMP systems, and the only systems that exhibit this
+ * property implement MIPSr6 or higher so we constrain support for this to
+ * kernels that will run on such systems.
+ */
+# ifndef cpu_has_shared_ftlb_ram
+#  define cpu_has_shared_ftlb_ram \
+	__isa_ge_and_opt(6, MIPS_CPU_SHARED_FTLB_RAM)
+# endif
+
+/*
+ * Some systems take this a step further & share FTLB entries between siblings.
+ * This is implemented as TLB writes happening as usual, but if an entry
+ * written by a sibling exists in the shared FTLB for a translation which would
+ * otherwise cause a TLB refill exception then the CPU will use the entry
+ * written by its sibling rather than triggering a refill & writing a matching
+ * TLB entry for itself.
+ *
+ * This is naturally only valid if a TLB entry is known to be suitable for use
+ * on all siblings in a CPU, and so it only takes effect when MMIDs are in use
+ * rather than ASIDs or when a TLB entry is marked global.
+ */
+# ifndef cpu_has_shared_ftlb_entries
+#  define cpu_has_shared_ftlb_entries \
+	__isa_ge_and_opt(6, MIPS_CPU_SHARED_FTLB_ENTRIES)
+# endif
+#endif /* SMP */
+
+#ifndef cpu_has_shared_ftlb_ram
+# define cpu_has_shared_ftlb_ram 0
+#endif
+#ifndef cpu_has_shared_ftlb_entries
+# define cpu_has_shared_ftlb_entries 0
+#endif
+
+#ifdef CONFIG_MIPS_MT_SMP
+# define cpu_has_mipsmt_pertccounters \
+	__isa_lt_and_opt(6, MIPS_CPU_MT_PER_TC_PERF_COUNTERS)
+#else
+# define cpu_has_mipsmt_pertccounters 0
+#endif /* CONFIG_MIPS_MT_SMP */
+
+/*
+ * We only enable MMID support for configurations which natively support 64 bit
+ * atomics because getting good performance from the allocator relies upon
+ * efficient atomic64_*() functions.
+ */
+#ifndef cpu_has_mmid
+# ifdef CONFIG_GENERIC_ATOMIC64
+#  define cpu_has_mmid		0
+# else
+#  define cpu_has_mmid		__isa_ge_and_opt(6, MIPS_CPU_MMID)
+# endif
+#endif
+
+#ifndef cpu_has_mm_sysad
+# define cpu_has_mm_sysad	__opt(MIPS_CPU_MM_SYSAD)
+#endif
+
+#ifndef cpu_has_mm_full
+# define cpu_has_mm_full	__opt(MIPS_CPU_MM_FULL)
+#endif
+
+/*
+ * Guest capabilities
+ */
+#ifndef cpu_guest_has_conf1
+#define cpu_guest_has_conf1	(cpu_data[0].guest.conf & (1 << 1))
+#endif
+#ifndef cpu_guest_has_conf2
+#define cpu_guest_has_conf2	(cpu_data[0].guest.conf & (1 << 2))
+#endif
+#ifndef cpu_guest_has_conf3
+#define cpu_guest_has_conf3	(cpu_data[0].guest.conf & (1 << 3))
+#endif
+#ifndef cpu_guest_has_conf4
+#define cpu_guest_has_conf4	(cpu_data[0].guest.conf & (1 << 4))
+#endif
+#ifndef cpu_guest_has_conf5
+#define cpu_guest_has_conf5	(cpu_data[0].guest.conf & (1 << 5))
+#endif
+#ifndef cpu_guest_has_conf6
+#define cpu_guest_has_conf6	(cpu_data[0].guest.conf & (1 << 6))
+#endif
+#ifndef cpu_guest_has_conf7
+#define cpu_guest_has_conf7	(cpu_data[0].guest.conf & (1 << 7))
+#endif
+#ifndef cpu_guest_has_fpu
+#define cpu_guest_has_fpu	(cpu_data[0].guest.options & MIPS_CPU_FPU)
+#endif
+#ifndef cpu_guest_has_watch
+#define cpu_guest_has_watch	(cpu_data[0].guest.options & MIPS_CPU_WATCH)
+#endif
+#ifndef cpu_guest_has_contextconfig
+#define cpu_guest_has_contextconfig (cpu_data[0].guest.options & MIPS_CPU_CTXTC)
+#endif
+#ifndef cpu_guest_has_segments
+#define cpu_guest_has_segments	(cpu_data[0].guest.options & MIPS_CPU_SEGMENTS)
+#endif
+#ifndef cpu_guest_has_badinstr
+#define cpu_guest_has_badinstr	(cpu_data[0].guest.options & MIPS_CPU_BADINSTR)
+#endif
+#ifndef cpu_guest_has_badinstrp
+#define cpu_guest_has_badinstrp	(cpu_data[0].guest.options & MIPS_CPU_BADINSTRP)
+#endif
+#ifndef cpu_guest_has_htw
+#define cpu_guest_has_htw	(cpu_data[0].guest.options & MIPS_CPU_HTW)
+#endif
+#ifndef cpu_guest_has_ldpte
+#define cpu_guest_has_ldpte	(cpu_data[0].guest.options & MIPS_CPU_LDPTE)
+#endif
+#ifndef cpu_guest_has_mvh
+#define cpu_guest_has_mvh	(cpu_data[0].guest.options & MIPS_CPU_MVH)
+#endif
+#ifndef cpu_guest_has_msa
+#define cpu_guest_has_msa	(cpu_data[0].guest.ases & MIPS_ASE_MSA)
+#endif
+#ifndef cpu_guest_has_kscr
+#define cpu_guest_has_kscr(n)	(cpu_data[0].guest.kscratch_mask & (1u << (n)))
+#endif
+#ifndef cpu_guest_has_rw_llb
+#define cpu_guest_has_rw_llb	(cpu_has_mips_r6 || (cpu_data[0].guest.options & MIPS_CPU_RW_LLB))
+#endif
+#ifndef cpu_guest_has_perf
+#define cpu_guest_has_perf	(cpu_data[0].guest.options & MIPS_CPU_PERF)
+#endif
+#ifndef cpu_guest_has_maar
+#define cpu_guest_has_maar	(cpu_data[0].guest.options & MIPS_CPU_MAAR)
+#endif
+#ifndef cpu_guest_has_userlocal
+#define cpu_guest_has_userlocal	(cpu_data[0].guest.options & MIPS_CPU_ULRI)
+#endif
+
+/*
+ * Guest dynamic capabilities
+ */
+#ifndef cpu_guest_has_dyn_fpu
+#define cpu_guest_has_dyn_fpu	(cpu_data[0].guest.options_dyn & MIPS_CPU_FPU)
+#endif
+#ifndef cpu_guest_has_dyn_watch
+#define cpu_guest_has_dyn_watch	(cpu_data[0].guest.options_dyn & MIPS_CPU_WATCH)
+#endif
+#ifndef cpu_guest_has_dyn_contextconfig
+#define cpu_guest_has_dyn_contextconfig (cpu_data[0].guest.options_dyn & MIPS_CPU_CTXTC)
+#endif
+#ifndef cpu_guest_has_dyn_perf
+#define cpu_guest_has_dyn_perf	(cpu_data[0].guest.options_dyn & MIPS_CPU_PERF)
+#endif
+#ifndef cpu_guest_has_dyn_msa
+#define cpu_guest_has_dyn_msa	(cpu_data[0].guest.ases_dyn & MIPS_ASE_MSA)
+#endif
+#ifndef cpu_guest_has_dyn_maar
+#define cpu_guest_has_dyn_maar	(cpu_data[0].guest.options_dyn & MIPS_CPU_MAAR)
+#endif
+
+#endif /* __ASM_CPU_FEATURES_H */
diff --git a/arch/mips/include/asm/cpu-info.h b/arch/mips/include/asm/cpu-info.h
new file mode 100644
index 000000000..a600670d0
--- /dev/null
+++ b/arch/mips/include/asm/cpu-info.h
@@ -0,0 +1,219 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994 Waldorf GMBH
+ * Copyright (C) 1995, 1996, 1997, 1998, 1999, 2001, 2002, 2003 Ralf Baechle
+ * Copyright (C) 1996 Paul M. Antoine
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ * Copyright (C) 2004  Maciej W. Rozycki
+ */
+#ifndef __ASM_CPU_INFO_H
+#define __ASM_CPU_INFO_H
+
+#include <linux/cache.h>
+#include <linux/types.h>
+
+#include <asm/mipsregs.h>
+
+/*
+ * Descriptor for a cache
+ */
+struct cache_desc {
+	unsigned int waysize;	/* Bytes per way */
+	unsigned short sets;	/* Number of lines per set */
+	unsigned char ways;	/* Number of ways */
+	unsigned char linesz;	/* Size of line in bytes */
+	unsigned char waybit;	/* Bits to select in a cache set */
+	unsigned char flags;	/* Flags describing cache properties */
+};
+
+struct guest_info {
+	unsigned long		ases;
+	unsigned long		ases_dyn;
+	unsigned long long	options;
+	unsigned long long	options_dyn;
+	int			tlbsize;
+	u8			conf;
+	u8			kscratch_mask;
+};
+
+/*
+ * Flag definitions
+ */
+#define MIPS_CACHE_NOT_PRESENT	0x00000001
+#define MIPS_CACHE_VTAG		0x00000002	/* Virtually tagged cache */
+#define MIPS_CACHE_ALIASES	0x00000004	/* Cache could have aliases */
+#define MIPS_CACHE_IC_F_DC	0x00000008	/* Ic can refill from D-cache */
+#define MIPS_IC_SNOOPS_REMOTE	0x00000010	/* Ic snoops remote stores */
+#define MIPS_CACHE_PINDEX	0x00000020	/* Physically indexed cache */
+
+struct cpuinfo_mips {
+	u64			asid_cache;
+#ifdef CONFIG_MIPS_ASID_BITS_VARIABLE
+	unsigned long		asid_mask;
+#endif
+
+	/*
+	 * Capability and feature descriptor structure for MIPS CPU
+	 */
+	unsigned long		ases;
+	unsigned long long	options;
+	unsigned int		udelay_val;
+	unsigned int		processor_id;
+	unsigned int		fpu_id;
+	unsigned int		fpu_csr31;
+	unsigned int		fpu_msk31;
+	unsigned int		msa_id;
+	unsigned int		cputype;
+	int			isa_level;
+	int			tlbsize;
+	int			tlbsizevtlb;
+	int			tlbsizeftlbsets;
+	int			tlbsizeftlbways;
+	struct cache_desc	icache; /* Primary I-cache */
+	struct cache_desc	dcache; /* Primary D or combined I/D cache */
+	struct cache_desc	vcache; /* Victim cache, between pcache and scache */
+	struct cache_desc	scache; /* Secondary cache */
+	struct cache_desc	tcache; /* Tertiary/split secondary cache */
+	int			srsets; /* Shadow register sets */
+	int			package;/* physical package number */
+	unsigned int		globalnumber;
+#ifdef CONFIG_64BIT
+	int			vmbits; /* Virtual memory size in bits */
+#endif
+	void			*data;	/* Additional data */
+	unsigned int		watch_reg_count;   /* Number that exist */
+	unsigned int		watch_reg_use_cnt; /* Usable by ptrace */
+#define NUM_WATCH_REGS 4
+	u16			watch_reg_masks[NUM_WATCH_REGS];
+	unsigned int		kscratch_mask; /* Usable KScratch mask. */
+	/*
+	 * Cache Coherency attribute for write-combine memory writes.
+	 * (shifted by _CACHE_SHIFT)
+	 */
+	unsigned int		writecombine;
+	/*
+	 * Simple counter to prevent enabling HTW in nested
+	 * htw_start/htw_stop calls
+	 */
+	unsigned int		htw_seq;
+
+	/* VZ & Guest features */
+	struct guest_info	guest;
+	unsigned int		gtoffset_mask;
+	unsigned int		guestid_mask;
+	unsigned int		guestid_cache;
+
+#ifdef CONFIG_CPU_LOONGSON3_CPUCFG_EMULATION
+	/* CPUCFG data for this CPU, synthesized at probe time.
+	 *
+	 * CPUCFG select 0 is PRId, 4 and above are unimplemented for now.
+	 * So the only stored values are for CPUCFG selects 1-3 inclusive.
+	 */
+	u32 loongson3_cpucfg_data[3];
+#endif
+} __attribute__((aligned(SMP_CACHE_BYTES)));
+
+extern struct cpuinfo_mips cpu_data[];
+#define current_cpu_data cpu_data[smp_processor_id()]
+#define raw_current_cpu_data cpu_data[raw_smp_processor_id()]
+#define boot_cpu_data cpu_data[0]
+
+extern void cpu_probe(void);
+extern void cpu_report(void);
+
+extern const char *__cpu_name[];
+#define cpu_name_string()	__cpu_name[raw_smp_processor_id()]
+
+struct seq_file;
+struct notifier_block;
+
+extern int register_proc_cpuinfo_notifier(struct notifier_block *nb);
+extern int proc_cpuinfo_notifier_call_chain(unsigned long val, void *v);
+
+#define proc_cpuinfo_notifier(fn, pri)					\
+({									\
+	static struct notifier_block fn##_nb = {			\
+		.notifier_call = fn,					\
+		.priority = pri						\
+	};								\
+									\
+	register_proc_cpuinfo_notifier(&fn##_nb);			\
+})
+
+struct proc_cpuinfo_notifier_args {
+	struct seq_file *m;
+	unsigned long n;
+};
+
+static inline unsigned int cpu_cluster(struct cpuinfo_mips *cpuinfo)
+{
+	/* Optimisation for systems where multiple clusters aren't used */
+	if (!IS_ENABLED(CONFIG_CPU_MIPSR5) && !IS_ENABLED(CONFIG_CPU_MIPSR6))
+		return 0;
+
+	return (cpuinfo->globalnumber & MIPS_GLOBALNUMBER_CLUSTER) >>
+		MIPS_GLOBALNUMBER_CLUSTER_SHF;
+}
+
+static inline unsigned int cpu_core(struct cpuinfo_mips *cpuinfo)
+{
+	return (cpuinfo->globalnumber & MIPS_GLOBALNUMBER_CORE) >>
+		MIPS_GLOBALNUMBER_CORE_SHF;
+}
+
+static inline unsigned int cpu_vpe_id(struct cpuinfo_mips *cpuinfo)
+{
+	/* Optimisation for systems where VP(E)s aren't used */
+	if (!IS_ENABLED(CONFIG_MIPS_MT_SMP) && !IS_ENABLED(CONFIG_CPU_MIPSR6))
+		return 0;
+
+	return (cpuinfo->globalnumber & MIPS_GLOBALNUMBER_VP) >>
+		MIPS_GLOBALNUMBER_VP_SHF;
+}
+
+extern void cpu_set_cluster(struct cpuinfo_mips *cpuinfo, unsigned int cluster);
+extern void cpu_set_core(struct cpuinfo_mips *cpuinfo, unsigned int core);
+extern void cpu_set_vpe_id(struct cpuinfo_mips *cpuinfo, unsigned int vpe);
+
+static inline bool cpus_are_siblings(int cpua, int cpub)
+{
+	struct cpuinfo_mips *infoa = &cpu_data[cpua];
+	struct cpuinfo_mips *infob = &cpu_data[cpub];
+	unsigned int gnuma, gnumb;
+
+	if (infoa->package != infob->package)
+		return false;
+
+	gnuma = infoa->globalnumber & ~MIPS_GLOBALNUMBER_VP;
+	gnumb = infob->globalnumber & ~MIPS_GLOBALNUMBER_VP;
+	if (gnuma != gnumb)
+		return false;
+
+	return true;
+}
+
+static inline unsigned long cpu_asid_inc(void)
+{
+	return 1 << CONFIG_MIPS_ASID_SHIFT;
+}
+
+static inline unsigned long cpu_asid_mask(struct cpuinfo_mips *cpuinfo)
+{
+#ifdef CONFIG_MIPS_ASID_BITS_VARIABLE
+	return cpuinfo->asid_mask;
+#endif
+	return ((1 << CONFIG_MIPS_ASID_BITS) - 1) << CONFIG_MIPS_ASID_SHIFT;
+}
+
+static inline void set_cpu_asid_mask(struct cpuinfo_mips *cpuinfo,
+				     unsigned long asid_mask)
+{
+#ifdef CONFIG_MIPS_ASID_BITS_VARIABLE
+	cpuinfo->asid_mask = asid_mask;
+#endif
+}
+
+#endif /* __ASM_CPU_INFO_H */
diff --git a/arch/mips/include/asm/cpu-type.h b/arch/mips/include/asm/cpu-type.h
new file mode 100644
index 000000000..a4a66bd93
--- /dev/null
+++ b/arch/mips/include/asm/cpu-type.h
@@ -0,0 +1,203 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003, 2004 Ralf Baechle
+ * Copyright (C) 2004  Maciej W. Rozycki
+ */
+#ifndef __ASM_CPU_TYPE_H
+#define __ASM_CPU_TYPE_H
+
+#include <linux/smp.h>
+#include <linux/compiler.h>
+
+static inline int __pure __get_cpu_type(const int cpu_type)
+{
+	switch (cpu_type) {
+#if defined(CONFIG_SYS_HAS_CPU_LOONGSON2E) || \
+    defined(CONFIG_SYS_HAS_CPU_LOONGSON2F)
+	case CPU_LOONGSON2EF:
+#endif
+
+#ifdef CONFIG_SYS_HAS_CPU_LOONGSON64
+	case CPU_LOONGSON64:
+#endif
+
+#if defined(CONFIG_SYS_HAS_CPU_LOONGSON1B) || \
+    defined(CONFIG_SYS_HAS_CPU_LOONGSON1C)
+	case CPU_LOONGSON32:
+#endif
+
+#ifdef CONFIG_SYS_HAS_CPU_MIPS32_R1
+	case CPU_4KC:
+	case CPU_ALCHEMY:
+	case CPU_PR4450:
+#endif
+
+#if defined(CONFIG_SYS_HAS_CPU_MIPS32_R1) || \
+    defined(CONFIG_SYS_HAS_CPU_MIPS32_R2)
+	case CPU_4KEC:
+	case CPU_XBURST:
+#endif
+
+#ifdef CONFIG_SYS_HAS_CPU_MIPS32_R2
+	case CPU_4KSC:
+	case CPU_24K:
+	case CPU_34K:
+	case CPU_1004K:
+	case CPU_74K:
+	case CPU_1074K:
+	case CPU_M14KC:
+	case CPU_M14KEC:
+	case CPU_INTERAPTIV:
+	case CPU_PROAPTIV:
+#endif
+
+#ifdef CONFIG_SYS_HAS_CPU_MIPS32_R5
+	case CPU_M5150:
+	case CPU_P5600:
+#endif
+
+#if defined(CONFIG_SYS_HAS_CPU_MIPS32_R2) || \
+    defined(CONFIG_SYS_HAS_CPU_MIPS32_R5) || \
+    defined(CONFIG_SYS_HAS_CPU_MIPS32_R6) || \
+    defined(CONFIG_SYS_HAS_CPU_MIPS64_R2) || \
+    defined(CONFIG_SYS_HAS_CPU_MIPS64_R5) || \
+    defined(CONFIG_SYS_HAS_CPU_MIPS64_R6)
+	case CPU_QEMU_GENERIC:
+#endif
+
+#ifdef CONFIG_SYS_HAS_CPU_MIPS64_R1
+	case CPU_5KC:
+	case CPU_5KE:
+	case CPU_20KC:
+	case CPU_25KF:
+	case CPU_SB1:
+	case CPU_SB1A:
+#endif
+
+#ifdef CONFIG_SYS_HAS_CPU_MIPS64_R2
+	/*
+	 * All MIPS64 R2 processors have their own special symbols.  That is,
+	 * there currently is no pure R2 core
+	 */
+#endif
+
+#ifdef CONFIG_SYS_HAS_CPU_MIPS32_R6
+	case CPU_M6250:
+#endif
+
+#ifdef CONFIG_SYS_HAS_CPU_MIPS64_R6
+	case CPU_I6400:
+	case CPU_I6500:
+	case CPU_P6600:
+#endif
+
+#ifdef CONFIG_SYS_HAS_CPU_R3000
+	case CPU_R2000:
+	case CPU_R3000:
+	case CPU_R3000A:
+	case CPU_R3041:
+	case CPU_R3051:
+	case CPU_R3052:
+	case CPU_R3081:
+	case CPU_R3081E:
+#endif
+
+#ifdef CONFIG_SYS_HAS_CPU_R4300
+	case CPU_R4300:
+	case CPU_R4310:
+#endif
+
+#ifdef CONFIG_SYS_HAS_CPU_R4X00
+	case CPU_R4000PC:
+	case CPU_R4000SC:
+	case CPU_R4000MC:
+	case CPU_R4200:
+	case CPU_R4400PC:
+	case CPU_R4400SC:
+	case CPU_R4400MC:
+	case CPU_R4600:
+	case CPU_R4700:
+	case CPU_R4640:
+	case CPU_R4650:
+#endif
+
+#ifdef CONFIG_SYS_HAS_CPU_TX49XX
+	case CPU_TX49XX:
+#endif
+
+#ifdef CONFIG_SYS_HAS_CPU_R5000
+	case CPU_R5000:
+#endif
+
+#ifdef CONFIG_SYS_HAS_CPU_R5500
+	case CPU_R5500:
+#endif
+
+#ifdef CONFIG_SYS_HAS_CPU_NEVADA
+	case CPU_NEVADA:
+#endif
+
+#ifdef CONFIG_SYS_HAS_CPU_R10000
+	case CPU_R10000:
+	case CPU_R12000:
+	case CPU_R14000:
+	case CPU_R16000:
+#endif
+#ifdef CONFIG_SYS_HAS_CPU_RM7000
+	case CPU_RM7000:
+	case CPU_SR71000:
+#endif
+#ifdef CONFIG_SYS_HAS_CPU_SB1
+	case CPU_SB1:
+	case CPU_SB1A:
+#endif
+#ifdef CONFIG_SYS_HAS_CPU_CAVIUM_OCTEON
+	case CPU_CAVIUM_OCTEON:
+	case CPU_CAVIUM_OCTEON_PLUS:
+	case CPU_CAVIUM_OCTEON2:
+	case CPU_CAVIUM_OCTEON3:
+#endif
+
+#if defined(CONFIG_SYS_HAS_CPU_BMIPS32_3300) || \
+	defined (CONFIG_SYS_HAS_CPU_MIPS32_R1)
+	case CPU_BMIPS32:
+	case CPU_BMIPS3300:
+#endif
+
+#ifdef CONFIG_SYS_HAS_CPU_BMIPS4350
+	case CPU_BMIPS4350:
+#endif
+
+#ifdef CONFIG_SYS_HAS_CPU_BMIPS4380
+	case CPU_BMIPS4380:
+#endif
+
+#ifdef CONFIG_SYS_HAS_CPU_BMIPS5000
+	case CPU_BMIPS5000:
+#endif
+		break;
+	default:
+		unreachable();
+	}
+
+	return cpu_type;
+}
+
+static inline int __pure current_cpu_type(void)
+{
+	const int cpu_type = current_cpu_data.cputype;
+
+	return __get_cpu_type(cpu_type);
+}
+
+static inline int __pure boot_cpu_type(void)
+{
+	const int cpu_type = cpu_data[0].cputype;
+
+	return __get_cpu_type(cpu_type);
+}
+
+#endif /* __ASM_CPU_TYPE_H */
diff --git a/arch/mips/include/asm/cpu.h b/arch/mips/include/asm/cpu.h
new file mode 100644
index 000000000..ecb9854cb
--- /dev/null
+++ b/arch/mips/include/asm/cpu.h
@@ -0,0 +1,444 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * cpu.h: Values of the PRId register used to match up
+ *	  various MIPS cpu types.
+ *
+ * Copyright (C) 1996 David S. Miller (davem@davemloft.net)
+ * Copyright (C) 2004, 2013  Maciej W. Rozycki
+ */
+#ifndef _ASM_CPU_H
+#define _ASM_CPU_H
+
+#include <linux/bits.h>
+
+/*
+   As of the MIPS32 and MIPS64 specs from MTI, the PRId register (CP0
+   register 15, select 0) is defined in this (backwards compatible) way:
+
+  +----------------+----------------+----------------+----------------+
+  | Company Options| Company ID	    | Processor ID   | Revision	      |
+  +----------------+----------------+----------------+----------------+
+   31		 24 23		  16 15		    8 7
+
+   I don't have docs for all the previous processors, but my impression is
+   that bits 16-23 have been 0 for all MIPS processors before the MIPS32/64
+   spec.
+*/
+
+#define PRID_OPT_MASK		0xff000000
+
+/*
+ * Assigned Company values for bits 23:16 of the PRId register.
+ */
+
+#define PRID_COMP_MASK		0xff0000
+
+#define PRID_COMP_LEGACY	0x000000
+#define PRID_COMP_MIPS		0x010000
+#define PRID_COMP_BROADCOM	0x020000
+#define PRID_COMP_ALCHEMY	0x030000
+#define PRID_COMP_SIBYTE	0x040000
+#define PRID_COMP_SANDCRAFT	0x050000
+#define PRID_COMP_NXP		0x060000
+#define PRID_COMP_TOSHIBA	0x070000
+#define PRID_COMP_LSI		0x080000
+#define PRID_COMP_LEXRA		0x0b0000
+#define PRID_COMP_NETLOGIC	0x0c0000
+#define PRID_COMP_CAVIUM	0x0d0000
+#define PRID_COMP_LOONGSON	0x140000
+#define PRID_COMP_INGENIC_13	0x130000	/* X2000, X2100 */
+#define PRID_COMP_INGENIC_D0	0xd00000	/* JZ4730, JZ4740, JZ4750, JZ4755, JZ4760, X1830 */
+#define PRID_COMP_INGENIC_D1	0xd10000	/* JZ4770, JZ4775, X1000 */
+#define PRID_COMP_INGENIC_E1	0xe10000	/* JZ4780 */
+
+/*
+ * Assigned Processor ID (implementation) values for bits 15:8 of the PRId
+ * register.  In order to detect a certain CPU type exactly eventually
+ * additional registers may need to be examined.
+ */
+
+#define PRID_IMP_MASK		0xff00
+
+/*
+ * These are valid when 23:16 == PRID_COMP_LEGACY
+ */
+
+#define PRID_IMP_R2000		0x0100
+#define PRID_IMP_AU1_REV1	0x0100
+#define PRID_IMP_AU1_REV2	0x0200
+#define PRID_IMP_R3000		0x0200		/* Same as R2000A  */
+#define PRID_IMP_R6000		0x0300		/* Same as R3000A  */
+#define PRID_IMP_R4000		0x0400
+#define PRID_IMP_R6000A		0x0600
+#define PRID_IMP_R10000		0x0900
+#define PRID_IMP_R4300		0x0b00
+#define PRID_IMP_VR41XX		0x0c00
+#define PRID_IMP_R12000		0x0e00
+#define PRID_IMP_R14000		0x0f00		/* R14K && R16K */
+#define PRID_IMP_R8000		0x1000
+#define PRID_IMP_PR4450		0x1200
+#define PRID_IMP_R4600		0x2000
+#define PRID_IMP_R4700		0x2100
+#define PRID_IMP_TX39		0x2200
+#define PRID_IMP_R4640		0x2200
+#define PRID_IMP_R4650		0x2200		/* Same as R4640 */
+#define PRID_IMP_R5000		0x2300
+#define PRID_IMP_TX49		0x2d00
+#define PRID_IMP_SONIC		0x2400
+#define PRID_IMP_MAGIC		0x2500
+#define PRID_IMP_RM7000		0x2700
+#define PRID_IMP_NEVADA		0x2800		/* RM5260 ??? */
+#define PRID_IMP_RM9000		0x3400
+#define PRID_IMP_LOONGSON_32	0x4200  /* Loongson-1 */
+#define PRID_IMP_R5432		0x5400
+#define PRID_IMP_R5500		0x5500
+#define PRID_IMP_LOONGSON_64R	0x6100  /* Reduced Loongson-2 */
+#define PRID_IMP_LOONGSON_64C	0x6300  /* Classic Loongson-2 and Loongson-3 */
+#define PRID_IMP_LOONGSON_64G	0xc000  /* Generic Loongson-2 and Loongson-3 */
+
+#define PRID_IMP_UNKNOWN	0xff00
+
+/*
+ * These are the PRID's for when 23:16 == PRID_COMP_MIPS
+ */
+
+#define PRID_IMP_QEMU_GENERIC	0x0000
+#define PRID_IMP_4KC		0x8000
+#define PRID_IMP_5KC		0x8100
+#define PRID_IMP_20KC		0x8200
+#define PRID_IMP_4KEC		0x8400
+#define PRID_IMP_4KSC		0x8600
+#define PRID_IMP_25KF		0x8800
+#define PRID_IMP_5KE		0x8900
+#define PRID_IMP_4KECR2		0x9000
+#define PRID_IMP_4KEMPR2	0x9100
+#define PRID_IMP_4KSD		0x9200
+#define PRID_IMP_24K		0x9300
+#define PRID_IMP_34K		0x9500
+#define PRID_IMP_24KE		0x9600
+#define PRID_IMP_74K		0x9700
+#define PRID_IMP_1004K		0x9900
+#define PRID_IMP_1074K		0x9a00
+#define PRID_IMP_M14KC		0x9c00
+#define PRID_IMP_M14KEC		0x9e00
+#define PRID_IMP_INTERAPTIV_UP	0xa000
+#define PRID_IMP_INTERAPTIV_MP	0xa100
+#define PRID_IMP_PROAPTIV_UP	0xa200
+#define PRID_IMP_PROAPTIV_MP	0xa300
+#define PRID_IMP_P6600		0xa400
+#define PRID_IMP_M5150		0xa700
+#define PRID_IMP_P5600		0xa800
+#define PRID_IMP_I6400		0xa900
+#define PRID_IMP_M6250		0xab00
+#define PRID_IMP_I6500		0xb000
+
+/*
+ * These are the PRID's for when 23:16 == PRID_COMP_SIBYTE
+ */
+
+#define PRID_IMP_SB1		0x0100
+#define PRID_IMP_SB1A		0x1100
+
+/*
+ * These are the PRID's for when 23:16 == PRID_COMP_SANDCRAFT
+ */
+
+#define PRID_IMP_SR71000	0x0400
+
+/*
+ * These are the PRID's for when 23:16 == PRID_COMP_BROADCOM
+ */
+
+#define PRID_IMP_BMIPS32_REV4	0x4000
+#define PRID_IMP_BMIPS32_REV8	0x8000
+#define PRID_IMP_BMIPS3300	0x9000
+#define PRID_IMP_BMIPS3300_ALT	0x9100
+#define PRID_IMP_BMIPS3300_BUG	0x0000
+#define PRID_IMP_BMIPS43XX	0xa000
+#define PRID_IMP_BMIPS5000	0x5a00
+#define PRID_IMP_BMIPS5200	0x5b00
+
+#define PRID_REV_BMIPS4380_LO	0x0040
+#define PRID_REV_BMIPS4380_HI	0x006f
+
+/*
+ * These are the PRID's for when 23:16 == PRID_COMP_CAVIUM
+ */
+
+#define PRID_IMP_CAVIUM_CN38XX 0x0000
+#define PRID_IMP_CAVIUM_CN31XX 0x0100
+#define PRID_IMP_CAVIUM_CN30XX 0x0200
+#define PRID_IMP_CAVIUM_CN58XX 0x0300
+#define PRID_IMP_CAVIUM_CN56XX 0x0400
+#define PRID_IMP_CAVIUM_CN50XX 0x0600
+#define PRID_IMP_CAVIUM_CN52XX 0x0700
+#define PRID_IMP_CAVIUM_CN63XX 0x9000
+#define PRID_IMP_CAVIUM_CN68XX 0x9100
+#define PRID_IMP_CAVIUM_CN66XX 0x9200
+#define PRID_IMP_CAVIUM_CN61XX 0x9300
+#define PRID_IMP_CAVIUM_CNF71XX 0x9400
+#define PRID_IMP_CAVIUM_CN78XX 0x9500
+#define PRID_IMP_CAVIUM_CN70XX 0x9600
+#define PRID_IMP_CAVIUM_CN73XX 0x9700
+#define PRID_IMP_CAVIUM_CNF75XX 0x9800
+
+/*
+ * These are the PRID's for when 23:16 == PRID_COMP_INGENIC_*
+ */
+
+#define PRID_IMP_XBURST_REV1	0x0200	/* XBurst®1 with MXU1.0/MXU1.1 SIMD ISA	*/
+#define PRID_IMP_XBURST_REV2	0x0100	/* XBurst®1 with MXU2.0 SIMD ISA		*/
+#define PRID_IMP_XBURST2		0x2000	/* XBurst®2 with MXU2.1 SIMD ISA		*/
+
+/*
+ * These are the PRID's for when 23:16 == PRID_COMP_NETLOGIC
+ */
+#define PRID_IMP_NETLOGIC_XLR732	0x0000
+#define PRID_IMP_NETLOGIC_XLR716	0x0200
+#define PRID_IMP_NETLOGIC_XLR532	0x0900
+#define PRID_IMP_NETLOGIC_XLR308	0x0600
+#define PRID_IMP_NETLOGIC_XLR532C	0x0800
+#define PRID_IMP_NETLOGIC_XLR516C	0x0a00
+#define PRID_IMP_NETLOGIC_XLR508C	0x0b00
+#define PRID_IMP_NETLOGIC_XLR308C	0x0f00
+#define PRID_IMP_NETLOGIC_XLS608	0x8000
+#define PRID_IMP_NETLOGIC_XLS408	0x8800
+#define PRID_IMP_NETLOGIC_XLS404	0x8c00
+#define PRID_IMP_NETLOGIC_XLS208	0x8e00
+#define PRID_IMP_NETLOGIC_XLS204	0x8f00
+#define PRID_IMP_NETLOGIC_XLS108	0xce00
+#define PRID_IMP_NETLOGIC_XLS104	0xcf00
+#define PRID_IMP_NETLOGIC_XLS616B	0x4000
+#define PRID_IMP_NETLOGIC_XLS608B	0x4a00
+#define PRID_IMP_NETLOGIC_XLS416B	0x4400
+#define PRID_IMP_NETLOGIC_XLS412B	0x4c00
+#define PRID_IMP_NETLOGIC_XLS408B	0x4e00
+#define PRID_IMP_NETLOGIC_XLS404B	0x4f00
+#define PRID_IMP_NETLOGIC_AU13XX	0x8000
+
+#define PRID_IMP_NETLOGIC_XLP8XX	0x1000
+#define PRID_IMP_NETLOGIC_XLP3XX	0x1100
+#define PRID_IMP_NETLOGIC_XLP2XX	0x1200
+#define PRID_IMP_NETLOGIC_XLP9XX	0x1500
+#define PRID_IMP_NETLOGIC_XLP5XX	0x1300
+
+/*
+ * Particular Revision values for bits 7:0 of the PRId register.
+ */
+
+#define PRID_REV_MASK		0x00ff
+
+/*
+ * Definitions for 7:0 on legacy processors
+ */
+
+#define PRID_REV_TX4927			0x0022
+#define PRID_REV_TX4937			0x0030
+#define PRID_REV_R4400			0x0040
+#define PRID_REV_R3000A			0x0030
+#define PRID_REV_R3000			0x0020
+#define PRID_REV_R2000A			0x0010
+#define PRID_REV_TX3912			0x0010
+#define PRID_REV_TX3922			0x0030
+#define PRID_REV_TX3927			0x0040
+#define PRID_REV_VR4111			0x0050
+#define PRID_REV_VR4181			0x0050	/* Same as VR4111 */
+#define PRID_REV_VR4121			0x0060
+#define PRID_REV_VR4122			0x0070
+#define PRID_REV_VR4181A		0x0070	/* Same as VR4122 */
+#define PRID_REV_VR4130			0x0080
+#define PRID_REV_34K_V1_0_2		0x0022
+#define PRID_REV_LOONGSON1B		0x0020
+#define PRID_REV_LOONGSON1C		0x0020	/* Same as Loongson-1B */
+#define PRID_REV_LOONGSON2E		0x0002
+#define PRID_REV_LOONGSON2F		0x0003
+#define PRID_REV_LOONGSON2K_R1_0	0x0000
+#define PRID_REV_LOONGSON2K_R1_1	0x0001
+#define PRID_REV_LOONGSON2K_R1_2	0x0002
+#define PRID_REV_LOONGSON2K_R1_3	0x0003
+#define PRID_REV_LOONGSON3A_R1		0x0005
+#define PRID_REV_LOONGSON3B_R1		0x0006
+#define PRID_REV_LOONGSON3B_R2		0x0007
+#define PRID_REV_LOONGSON3A_R2_0	0x0008
+#define PRID_REV_LOONGSON3A_R3_0	0x0009
+#define PRID_REV_LOONGSON3A_R2_1	0x000c
+#define PRID_REV_LOONGSON3A_R3_1	0x000d
+
+/*
+ * Older processors used to encode processor version and revision in two
+ * 4-bit bitfields, the 4K seems to simply count up and even newer MTI cores
+ * have switched to use the 8-bits as 3:3:2 bitfield with the last field as
+ * the patch number.  *ARGH*
+ */
+#define PRID_REV_ENCODE_44(ver, rev)					\
+	((ver) << 4 | (rev))
+#define PRID_REV_ENCODE_332(ver, rev, patch)				\
+	((ver) << 5 | (rev) << 2 | (patch))
+
+/*
+ * FPU implementation/revision register (CP1 control register 0).
+ *
+ * +---------------------------------+----------------+----------------+
+ * | 0				     | Implementation | Revision       |
+ * +---------------------------------+----------------+----------------+
+ *  31				   16 15	     8 7	      0
+ */
+
+#define FPIR_IMP_MASK		0xff00
+
+#define FPIR_IMP_NONE		0x0000
+
+#if !defined(__ASSEMBLY__)
+
+enum cpu_type_enum {
+	CPU_UNKNOWN,
+
+	/*
+	 * R2000 class processors
+	 */
+	CPU_R2000, CPU_R3000, CPU_R3000A, CPU_R3041, CPU_R3051, CPU_R3052,
+	CPU_R3081, CPU_R3081E,
+
+	/*
+	 * R4000 class processors
+	 */
+	CPU_R4000PC, CPU_R4000SC, CPU_R4000MC, CPU_R4200, CPU_R4300, CPU_R4310,
+	CPU_R4400PC, CPU_R4400SC, CPU_R4400MC, CPU_R4600, CPU_R4640, CPU_R4650,
+	CPU_R4700, CPU_R5000, CPU_R5500, CPU_NEVADA, CPU_R10000,
+	CPU_R12000, CPU_R14000, CPU_R16000, CPU_RM7000,
+	CPU_SR71000, CPU_TX49XX,
+
+	/*
+	 * MIPS32 class processors
+	 */
+	CPU_4KC, CPU_4KEC, CPU_4KSC, CPU_24K, CPU_34K, CPU_1004K, CPU_74K,
+	CPU_ALCHEMY, CPU_PR4450, CPU_BMIPS32, CPU_BMIPS3300, CPU_BMIPS4350,
+	CPU_BMIPS4380, CPU_BMIPS5000, CPU_XBURST, CPU_LOONGSON32, CPU_M14KC,
+	CPU_M14KEC, CPU_INTERAPTIV, CPU_P5600, CPU_PROAPTIV, CPU_1074K,
+	CPU_M5150, CPU_I6400, CPU_P6600, CPU_M6250,
+
+	/*
+	 * MIPS64 class processors
+	 */
+	CPU_5KC, CPU_5KE, CPU_20KC, CPU_25KF, CPU_SB1, CPU_SB1A, CPU_LOONGSON2EF,
+	CPU_LOONGSON64, CPU_CAVIUM_OCTEON, CPU_CAVIUM_OCTEON_PLUS,
+	CPU_CAVIUM_OCTEON2, CPU_CAVIUM_OCTEON3, CPU_I6500,
+
+	CPU_QEMU_GENERIC,
+
+	CPU_LAST
+};
+
+#endif /* !__ASSEMBLY */
+
+/*
+ * ISA Level encodings
+ *
+ */
+#define MIPS_CPU_ISA_II		0x00000001
+#define MIPS_CPU_ISA_III	0x00000002
+#define MIPS_CPU_ISA_IV		0x00000004
+#define MIPS_CPU_ISA_V		0x00000008
+#define MIPS_CPU_ISA_M32R1	0x00000010
+#define MIPS_CPU_ISA_M32R2	0x00000020
+#define MIPS_CPU_ISA_M64R1	0x00000040
+#define MIPS_CPU_ISA_M64R2	0x00000080
+#define MIPS_CPU_ISA_M32R5	0x00000100
+#define MIPS_CPU_ISA_M64R5	0x00000200
+#define MIPS_CPU_ISA_M32R6	0x00000400
+#define MIPS_CPU_ISA_M64R6	0x00000800
+
+#define MIPS_CPU_ISA_32BIT (MIPS_CPU_ISA_II | MIPS_CPU_ISA_M32R1 | \
+	MIPS_CPU_ISA_M32R2 | MIPS_CPU_ISA_M32R5 | MIPS_CPU_ISA_M32R6)
+#define MIPS_CPU_ISA_64BIT (MIPS_CPU_ISA_III | MIPS_CPU_ISA_IV | \
+	MIPS_CPU_ISA_V | MIPS_CPU_ISA_M64R1 | MIPS_CPU_ISA_M64R2 | \
+	MIPS_CPU_ISA_M64R5 | MIPS_CPU_ISA_M64R6)
+
+/*
+ * CPU Option encodings
+ */
+#define MIPS_CPU_TLB		BIT_ULL( 0)	/* CPU has TLB */
+#define MIPS_CPU_4KEX		BIT_ULL( 1)	/* "R4K" exception model */
+#define MIPS_CPU_3K_CACHE	BIT_ULL( 2)	/* R3000-style caches */
+#define MIPS_CPU_4K_CACHE	BIT_ULL( 3)	/* R4000-style caches */
+#define MIPS_CPU_FPU		BIT_ULL( 5)	/* CPU has FPU */
+#define MIPS_CPU_32FPR		BIT_ULL( 6)	/* 32 dbl. prec. FP registers */
+#define MIPS_CPU_COUNTER	BIT_ULL( 7)	/* Cycle count/compare */
+#define MIPS_CPU_WATCH		BIT_ULL( 8)	/* watchpoint registers */
+#define MIPS_CPU_DIVEC		BIT_ULL( 9)	/* dedicated interrupt vector */
+#define MIPS_CPU_VCE		BIT_ULL(10)	/* virt. coherence conflict possible */
+#define MIPS_CPU_CACHE_CDEX_P	BIT_ULL(11)	/* Create_Dirty_Exclusive CACHE op */
+#define MIPS_CPU_CACHE_CDEX_S	BIT_ULL(12)	/* ... same for seconary cache ... */
+#define MIPS_CPU_MCHECK		BIT_ULL(13)	/* Machine check exception */
+#define MIPS_CPU_EJTAG		BIT_ULL(14)	/* EJTAG exception */
+#define MIPS_CPU_NOFPUEX	BIT_ULL(15)	/* no FPU exception */
+#define MIPS_CPU_LLSC		BIT_ULL(16)	/* CPU has ll/sc instructions */
+#define MIPS_CPU_INCLUSIVE_CACHES BIT_ULL(17)	/* P-cache subset enforced */
+#define MIPS_CPU_PREFETCH	BIT_ULL(18)	/* CPU has usable prefetch */
+#define MIPS_CPU_VINT		BIT_ULL(19)	/* CPU supports MIPSR2 vectored interrupts */
+#define MIPS_CPU_VEIC		BIT_ULL(20)	/* CPU supports MIPSR2 external interrupt controller mode */
+#define MIPS_CPU_ULRI		BIT_ULL(21)	/* CPU has ULRI feature */
+#define MIPS_CPU_PCI		BIT_ULL(22)	/* CPU has Perf Ctr Int indicator */
+#define MIPS_CPU_RIXI		BIT_ULL(23)	/* CPU has TLB Read/eXec Inhibit */
+#define MIPS_CPU_MICROMIPS	BIT_ULL(24)	/* CPU has microMIPS capability */
+#define MIPS_CPU_TLBINV		BIT_ULL(25)	/* CPU supports TLBINV/F */
+#define MIPS_CPU_SEGMENTS	BIT_ULL(26)	/* CPU supports Segmentation Control registers */
+#define MIPS_CPU_EVA		BIT_ULL(27)	/* CPU supports Enhanced Virtual Addressing */
+#define MIPS_CPU_HTW		BIT_ULL(28)	/* CPU support Hardware Page Table Walker */
+#define MIPS_CPU_RIXIEX		BIT_ULL(29)	/* CPU has unique exception codes for {Read, Execute}-Inhibit exceptions */
+#define MIPS_CPU_MAAR		BIT_ULL(30)	/* MAAR(I) registers are present */
+#define MIPS_CPU_FRE		BIT_ULL(31)	/* FRE & UFE bits implemented */
+#define MIPS_CPU_RW_LLB		BIT_ULL(32)	/* LLADDR/LLB writes are allowed */
+#define MIPS_CPU_LPA		BIT_ULL(33)	/* CPU supports Large Physical Addressing */
+#define MIPS_CPU_CDMM		BIT_ULL(34)	/* CPU has Common Device Memory Map */
+#define MIPS_CPU_SP		BIT_ULL(36)	/* Small (1KB) page support */
+#define MIPS_CPU_FTLB		BIT_ULL(37)	/* CPU has Fixed-page-size TLB */
+#define MIPS_CPU_NAN_LEGACY	BIT_ULL(38)	/* Legacy NaN implemented */
+#define MIPS_CPU_NAN_2008	BIT_ULL(39)	/* 2008 NaN implemented */
+#define MIPS_CPU_VP		BIT_ULL(40)	/* MIPSr6 Virtual Processors (multi-threading) */
+#define MIPS_CPU_LDPTE		BIT_ULL(41)	/* CPU has ldpte/lddir instructions */
+#define MIPS_CPU_MVH		BIT_ULL(42)	/* CPU supports MFHC0/MTHC0 */
+#define MIPS_CPU_EBASE_WG	BIT_ULL(43)	/* CPU has EBase.WG */
+#define MIPS_CPU_BADINSTR	BIT_ULL(44)	/* CPU has BadInstr register */
+#define MIPS_CPU_BADINSTRP	BIT_ULL(45)	/* CPU has BadInstrP register */
+#define MIPS_CPU_CTXTC		BIT_ULL(46)	/* CPU has [X]ConfigContext registers */
+#define MIPS_CPU_PERF		BIT_ULL(47)	/* CPU has MIPS performance counters */
+#define MIPS_CPU_GUESTCTL0EXT	BIT_ULL(48)	/* CPU has VZ GuestCtl0Ext register */
+#define MIPS_CPU_GUESTCTL1	BIT_ULL(49)	/* CPU has VZ GuestCtl1 register */
+#define MIPS_CPU_GUESTCTL2	BIT_ULL(50)	/* CPU has VZ GuestCtl2 register */
+#define MIPS_CPU_GUESTID	BIT_ULL(51)	/* CPU uses VZ ASE GuestID feature */
+#define MIPS_CPU_DRG		BIT_ULL(52)	/* CPU has VZ Direct Root to Guest (DRG) */
+#define MIPS_CPU_UFR		BIT_ULL(53)	/* CPU supports User mode FR switching */
+#define MIPS_CPU_SHARED_FTLB_RAM \
+				BIT_ULL(54)	/* CPU shares FTLB RAM with another */
+#define MIPS_CPU_SHARED_FTLB_ENTRIES \
+				BIT_ULL(55)	/* CPU shares FTLB entries with another */
+#define MIPS_CPU_MT_PER_TC_PERF_COUNTERS \
+				BIT_ULL(56)	/* CPU has perf counters implemented per TC (MIPSMT ASE) */
+#define MIPS_CPU_MMID		BIT_ULL(57)	/* CPU supports MemoryMapIDs */
+#define MIPS_CPU_MM_SYSAD	BIT_ULL(58)	/* CPU supports write-through SysAD Valid merge */
+#define MIPS_CPU_MM_FULL	BIT_ULL(59)	/* CPU supports write-through full merge */
+#define MIPS_CPU_MAC_2008_ONLY	BIT_ULL(60)	/* CPU Only support MAC2008 Fused multiply-add instruction */
+#define MIPS_CPU_FTLBPAREX	BIT_ULL(61)	/* CPU has FTLB parity exception */
+#define MIPS_CPU_GSEXCEX	BIT_ULL(62)	/* CPU has GSExc exception */
+
+/*
+ * CPU ASE encodings
+ */
+#define MIPS_ASE_MIPS16		0x00000001 /* code compression */
+#define MIPS_ASE_MDMX		0x00000002 /* MIPS digital media extension */
+#define MIPS_ASE_MIPS3D		0x00000004 /* MIPS-3D */
+#define MIPS_ASE_SMARTMIPS	0x00000008 /* SmartMIPS */
+#define MIPS_ASE_DSP		0x00000010 /* Signal Processing ASE */
+#define MIPS_ASE_MIPSMT		0x00000020 /* CPU supports MIPS MT */
+#define MIPS_ASE_DSP2P		0x00000040 /* Signal Processing ASE Rev 2 */
+#define MIPS_ASE_VZ		0x00000080 /* Virtualization ASE */
+#define MIPS_ASE_MSA		0x00000100 /* MIPS SIMD Architecture */
+#define MIPS_ASE_DSP3		0x00000200 /* Signal Processing ASE Rev 3*/
+#define MIPS_ASE_MIPS16E2	0x00000400 /* MIPS16e2 */
+#define MIPS_ASE_LOONGSON_MMI	0x00000800 /* Loongson MultiMedia extensions Instructions */
+#define MIPS_ASE_LOONGSON_CAM	0x00001000 /* Loongson CAM */
+#define MIPS_ASE_LOONGSON_EXT	0x00002000 /* Loongson EXTensions */
+#define MIPS_ASE_LOONGSON_EXT2	0x00004000 /* Loongson EXTensions R2 */
+
+#endif /* _ASM_CPU_H */
diff --git a/arch/mips/include/asm/cpufeature.h b/arch/mips/include/asm/cpufeature.h
new file mode 100644
index 000000000..ba9e62faf
--- /dev/null
+++ b/arch/mips/include/asm/cpufeature.h
@@ -0,0 +1,22 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * CPU feature definitions for module loading, used by
+ * module_cpu_feature_match(), see uapi/asm/hwcap.h for MIPS CPU features.
+ */
+
+#ifndef __ASM_CPUFEATURE_H
+#define __ASM_CPUFEATURE_H
+
+#include <uapi/asm/hwcap.h>
+#include <asm/elf.h>
+
+#define MAX_CPU_FEATURES (8 * sizeof(elf_hwcap))
+
+#define cpu_feature(x)		ilog2(HWCAP_ ## x)
+
+static inline bool cpu_have_feature(unsigned int num)
+{
+	return elf_hwcap & (1UL << num);
+}
+
+#endif /* __ASM_CPUFEATURE_H */
diff --git a/arch/mips/include/asm/debug.h b/arch/mips/include/asm/debug.h
new file mode 100644
index 000000000..c7013e1cb
--- /dev/null
+++ b/arch/mips/include/asm/debug.h
@@ -0,0 +1,18 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2015 Imagination Technologies
+ */
+
+#ifndef __MIPS_ASM_DEBUG_H__
+#define __MIPS_ASM_DEBUG_H__
+
+#include <linux/dcache.h>
+
+/*
+ * mips_debugfs_dir corresponds to the "mips" directory at the top level
+ * of the DebugFS hierarchy. MIPS-specific DebugFS entires should be
+ * placed beneath this directory.
+ */
+extern struct dentry *mips_debugfs_dir;
+
+#endif /* __MIPS_ASM_DEBUG_H__ */
diff --git a/arch/mips/include/asm/dec/ecc.h b/arch/mips/include/asm/dec/ecc.h
new file mode 100644
index 000000000..c3a3f71f1
--- /dev/null
+++ b/arch/mips/include/asm/dec/ecc.h
@@ -0,0 +1,51 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ *	include/asm-mips/dec/ecc.h
+ *
+ *	ECC handling logic definitions common to DECstation/DECsystem
+ *	5000/200 (KN02), 5000/240 (KN03), 5000/260 (KN05) and
+ *	DECsystem 5900 (KN03), 5900/260 (KN05) systems.
+ *
+ *	Copyright (C) 2003  Maciej W. Rozycki
+ */
+#ifndef __ASM_MIPS_DEC_ECC_H
+#define __ASM_MIPS_DEC_ECC_H
+
+/*
+ * Error Address Register bits.
+ * The register is r/wc -- any write clears it.
+ */
+#define KN0X_EAR_VALID		(1<<31)		/* error data valid, bus IRQ */
+#define KN0X_EAR_CPU		(1<<30)		/* CPU/DMA transaction */
+#define KN0X_EAR_WRITE		(1<<29)		/* write/read transaction */
+#define KN0X_EAR_ECCERR		(1<<28)		/* ECC/timeout or overrun */
+#define KN0X_EAR_RES_27		(1<<27)		/* unused */
+#define KN0X_EAR_ADDRESS	(0x7ffffff<<0)	/* address involved */
+
+/*
+ * Error Syndrome Register bits.
+ * The register is frozen when EAR.VALID is set, otherwise it records bits
+ * from the last memory read.  The register is r/wc -- any write clears it.
+ */
+#define KN0X_ESR_VLDHI		(1<<31)		/* error data valid hi word */
+#define KN0X_ESR_CHKHI		(0x7f<<24)	/* check bits read from mem */
+#define KN0X_ESR_SNGHI		(1<<23)		/* single/double bit error */
+#define KN0X_ESR_SYNHI		(0x7f<<16)	/* syndrome from ECC logic */
+#define KN0X_ESR_VLDLO		(1<<15)		/* error data valid lo word */
+#define KN0X_ESR_CHKLO		(0x7f<<8)	/* check bits read from mem */
+#define KN0X_ESR_SNGLO		(1<<7)		/* single/double bit error */
+#define KN0X_ESR_SYNLO		(0x7f<<0)	/* syndrome from ECC logic */
+
+
+#ifndef __ASSEMBLY__
+
+#include <linux/interrupt.h>
+
+struct pt_regs;
+
+extern void dec_ecc_be_init(void);
+extern int dec_ecc_be_handler(struct pt_regs *regs, int is_fixup);
+extern irqreturn_t dec_ecc_be_interrupt(int irq, void *dev_id);
+#endif
+
+#endif /* __ASM_MIPS_DEC_ECC_H */
diff --git a/arch/mips/include/asm/dec/interrupts.h b/arch/mips/include/asm/dec/interrupts.h
new file mode 100644
index 000000000..e10d34106
--- /dev/null
+++ b/arch/mips/include/asm/dec/interrupts.h
@@ -0,0 +1,126 @@
+/*
+ * Miscellaneous definitions used to initialise the interrupt vector table
+ * with the machine-specific interrupt routines.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1997 by Paul M. Antoine.
+ * reworked 1998 by Harald Koerfgen.
+ * Copyright (C) 2001, 2002, 2003  Maciej W. Rozycki
+ */
+
+#ifndef __ASM_DEC_INTERRUPTS_H
+#define __ASM_DEC_INTERRUPTS_H
+
+#include <irq.h>
+#include <asm/mipsregs.h>
+
+
+/*
+ * The list of possible system devices which provide an
+ * interrupt.  Not all devices exist on a given system.
+ */
+#define DEC_IRQ_CASCADE		0	/* cascade from CSR or I/O ASIC */
+
+/* Ordinary interrupts */
+#define DEC_IRQ_AB_RECV		1	/* ACCESS.bus receive */
+#define DEC_IRQ_AB_XMIT		2	/* ACCESS.bus transmit */
+#define DEC_IRQ_DZ11		3	/* DZ11 (DC7085) serial */
+#define DEC_IRQ_ASC		4	/* ASC (NCR53C94) SCSI */
+#define DEC_IRQ_FLOPPY		5	/* 82077 FDC */
+#define DEC_IRQ_FPU		6	/* R3k FPU */
+#define DEC_IRQ_HALT		7	/* HALT button or from ACCESS.Bus */
+#define DEC_IRQ_ISDN		8	/* Am79C30A ISDN */
+#define DEC_IRQ_LANCE		9	/* LANCE (Am7990) Ethernet */
+#define DEC_IRQ_BUS		10	/* memory, I/O bus read/write errors */
+#define DEC_IRQ_PSU		11	/* power supply unit warning */
+#define DEC_IRQ_RTC		12	/* DS1287 RTC */
+#define DEC_IRQ_SCC0		13	/* SCC (Z85C30) serial #0 */
+#define DEC_IRQ_SCC1		14	/* SCC (Z85C30) serial #1 */
+#define DEC_IRQ_SII		15	/* SII (DC7061) SCSI */
+#define DEC_IRQ_TC0		16	/* TURBOchannel slot #0 */
+#define DEC_IRQ_TC1		17	/* TURBOchannel slot #1 */
+#define DEC_IRQ_TC2		18	/* TURBOchannel slot #2 */
+#define DEC_IRQ_TIMER		19	/* ARC periodic timer */
+#define DEC_IRQ_VIDEO		20	/* framebuffer */
+
+/* I/O ASIC DMA interrupts */
+#define DEC_IRQ_ASC_MERR	21	/* ASC memory read error */
+#define DEC_IRQ_ASC_ERR		22	/* ASC page overrun */
+#define DEC_IRQ_ASC_DMA		23	/* ASC buffer pointer loaded */
+#define DEC_IRQ_FLOPPY_ERR	24	/* FDC error */
+#define DEC_IRQ_ISDN_ERR	25	/* ISDN memory read/overrun error */
+#define DEC_IRQ_ISDN_RXDMA	26	/* ISDN recv buffer pointer loaded */
+#define DEC_IRQ_ISDN_TXDMA	27	/* ISDN xmit buffer pointer loaded */
+#define DEC_IRQ_LANCE_MERR	28	/* LANCE memory read error */
+#define DEC_IRQ_SCC0A_RXERR	29	/* SCC0A (printer) receive overrun */
+#define DEC_IRQ_SCC0A_RXDMA	30	/* SCC0A receive half page */
+#define DEC_IRQ_SCC0A_TXERR	31	/* SCC0A xmit memory read/overrun */
+#define DEC_IRQ_SCC0A_TXDMA	32	/* SCC0A transmit page end */
+#define DEC_IRQ_AB_RXERR	33	/* ACCESS.bus receive overrun */
+#define DEC_IRQ_AB_RXDMA	34	/* ACCESS.bus receive half page */
+#define DEC_IRQ_AB_TXERR	35	/* ACCESS.bus xmit memory read/ovrn */
+#define DEC_IRQ_AB_TXDMA	36	/* ACCESS.bus transmit page end */
+#define DEC_IRQ_SCC1A_RXERR	37	/* SCC1A (modem) receive overrun */
+#define DEC_IRQ_SCC1A_RXDMA	38	/* SCC1A receive half page */
+#define DEC_IRQ_SCC1A_TXERR	39	/* SCC1A xmit memory read/overrun */
+#define DEC_IRQ_SCC1A_TXDMA	40	/* SCC1A transmit page end */
+
+/* TC5 & TC6 are virtual slots for KN02's onboard devices */
+#define DEC_IRQ_TC5		DEC_IRQ_ASC	/* virtual PMAZ-AA */
+#define DEC_IRQ_TC6		DEC_IRQ_LANCE	/* virtual PMAD-AA */
+
+#define DEC_NR_INTS		41
+
+
+/* Largest of cpu mask_nr tables. */
+#define DEC_MAX_CPU_INTS	6
+/* Largest of asic mask_nr tables. */
+#define DEC_MAX_ASIC_INTS	9
+
+
+/*
+ * CPU interrupt bits common to all systems.
+ */
+#define DEC_CPU_INR_FPU		7	/* R3k FPU */
+#define DEC_CPU_INR_SW1		1	/* software #1 */
+#define DEC_CPU_INR_SW0		0	/* software #0 */
+
+#define DEC_CPU_IRQ_BASE	MIPS_CPU_IRQ_BASE	/* first IRQ assigned to CPU */
+
+#define DEC_CPU_IRQ_NR(n)	((n) + DEC_CPU_IRQ_BASE)
+#define DEC_CPU_IRQ_MASK(n)	(1 << ((n) + CAUSEB_IP))
+#define DEC_CPU_IRQ_ALL		(0xff << CAUSEB_IP)
+
+
+#ifndef __ASSEMBLY__
+
+/*
+ * Interrupt table structures to hide differences between systems.
+ */
+typedef union { int i; void *p; } int_ptr;
+extern int dec_interrupt[DEC_NR_INTS];
+extern int_ptr cpu_mask_nr_tbl[DEC_MAX_CPU_INTS][2];
+extern int_ptr asic_mask_nr_tbl[DEC_MAX_ASIC_INTS][2];
+extern int cpu_fpu_mask;
+
+
+/*
+ * Common interrupt routine prototypes for all DECStations
+ */
+extern void kn02_io_int(void);
+extern void kn02xa_io_int(void);
+extern void kn03_io_int(void);
+extern void asic_dma_int(void);
+extern void asic_all_int(void);
+extern void kn02_all_int(void);
+extern void cpu_all_int(void);
+
+extern void dec_intr_unimplemented(void);
+extern void asic_intr_unimplemented(void);
+
+#endif /* __ASSEMBLY__ */
+
+#endif
diff --git a/arch/mips/include/asm/dec/ioasic.h b/arch/mips/include/asm/dec/ioasic.h
new file mode 100644
index 000000000..6d912f095
--- /dev/null
+++ b/arch/mips/include/asm/dec/ioasic.h
@@ -0,0 +1,34 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ *	include/asm-mips/dec/ioasic.h
+ *
+ *	DEC I/O ASIC access operations.
+ *
+ *	Copyright (C) 2000, 2002, 2003  Maciej W. Rozycki
+ */
+
+#ifndef __ASM_DEC_IOASIC_H
+#define __ASM_DEC_IOASIC_H
+
+#include <linux/spinlock.h>
+#include <linux/types.h>
+
+extern spinlock_t ioasic_ssr_lock;
+
+extern volatile u32 *ioasic_base;
+
+static inline void ioasic_write(unsigned int reg, u32 v)
+{
+	ioasic_base[reg / 4] = v;
+}
+
+static inline u32 ioasic_read(unsigned int reg)
+{
+	return ioasic_base[reg / 4];
+}
+
+extern void init_ioasic_irqs(int base);
+
+extern int dec_ioasic_clocksource_init(void);
+
+#endif /* __ASM_DEC_IOASIC_H */
diff --git a/arch/mips/include/asm/dec/ioasic_addrs.h b/arch/mips/include/asm/dec/ioasic_addrs.h
new file mode 100644
index 000000000..8bd95971f
--- /dev/null
+++ b/arch/mips/include/asm/dec/ioasic_addrs.h
@@ -0,0 +1,152 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Definitions for the address map in the JUNKIO Asic
+ *
+ * Created with Information from:
+ *
+ * "DEC 3000 300/400/500/600/700/800/900 AXP Models System Programmer's Manual"
+ *
+ * and the Mach Sources
+ *
+ * Copyright (C) 199x  the Anonymous
+ * Copyright (C) 2002, 2003  Maciej W. Rozycki
+ */
+
+#ifndef __ASM_MIPS_DEC_IOASIC_ADDRS_H
+#define __ASM_MIPS_DEC_IOASIC_ADDRS_H
+
+#define IOASIC_SLOT_SIZE 0x00040000
+
+/*
+ * Address ranges decoded by the I/O ASIC for onboard devices.
+ */
+#define IOASIC_SYS_ROM	(0*IOASIC_SLOT_SIZE)	/* system board ROM */
+#define IOASIC_IOCTL	(1*IOASIC_SLOT_SIZE)	/* I/O ASIC */
+#define IOASIC_ESAR	(2*IOASIC_SLOT_SIZE)	/* LANCE MAC address chip */
+#define IOASIC_LANCE	(3*IOASIC_SLOT_SIZE)	/* LANCE Ethernet */
+#define IOASIC_SCC0	(4*IOASIC_SLOT_SIZE)	/* SCC #0 */
+#define IOASIC_VDAC_HI	(5*IOASIC_SLOT_SIZE)	/* VDAC (maxine) */
+#define IOASIC_SCC1	(6*IOASIC_SLOT_SIZE)	/* SCC #1 (3min, 3max+) */
+#define IOASIC_VDAC_LO	(7*IOASIC_SLOT_SIZE)	/* VDAC (maxine) */
+#define IOASIC_TOY	(8*IOASIC_SLOT_SIZE)	/* RTC */
+#define IOASIC_ISDN	(9*IOASIC_SLOT_SIZE)	/* ISDN (maxine) */
+#define IOASIC_ERRADDR	(9*IOASIC_SLOT_SIZE)	/* bus error address (3max+) */
+#define IOASIC_CHKSYN	(10*IOASIC_SLOT_SIZE)	/* ECC syndrome (3max+) */
+#define IOASIC_ACC_BUS	(10*IOASIC_SLOT_SIZE)	/* ACCESS.bus (maxine) */
+#define IOASIC_MCR	(11*IOASIC_SLOT_SIZE)	/* memory control (3max+) */
+#define IOASIC_FLOPPY	(11*IOASIC_SLOT_SIZE)	/* FDC (maxine) */
+#define IOASIC_SCSI	(12*IOASIC_SLOT_SIZE)	/* ASC SCSI */
+#define IOASIC_FDC_DMA	(13*IOASIC_SLOT_SIZE)	/* FDC DMA (maxine) */
+#define IOASIC_SCSI_DMA	(14*IOASIC_SLOT_SIZE)	/* ??? */
+#define IOASIC_RES_15	(15*IOASIC_SLOT_SIZE)	/* unused? */
+
+
+/*
+ * Offsets for I/O ASIC registers
+ * (relative to (dec_kn_slot_base + IOASIC_IOCTL)).
+ */
+					/* all systems */
+#define IO_REG_SCSI_DMA_P	0x00	/* SCSI DMA Pointer */
+#define IO_REG_SCSI_DMA_BP	0x10	/* SCSI DMA Buffer Pointer */
+#define IO_REG_LANCE_DMA_P	0x20	/* LANCE DMA Pointer */
+#define IO_REG_SCC0A_T_DMA_P	0x30	/* SCC0A Transmit DMA Pointer */
+#define IO_REG_SCC0A_R_DMA_P	0x40	/* SCC0A Receive DMA Pointer */
+
+					/* except Maxine */
+#define IO_REG_SCC1A_T_DMA_P	0x50	/* SCC1A Transmit DMA Pointer */
+#define IO_REG_SCC1A_R_DMA_P	0x60	/* SCC1A Receive DMA Pointer */
+
+					/* Maxine */
+#define IO_REG_AB_T_DMA_P	0x50	/* ACCESS.bus Transmit DMA Pointer */
+#define IO_REG_AB_R_DMA_P	0x60	/* ACCESS.bus Receive DMA Pointer */
+#define IO_REG_FLOPPY_DMA_P	0x70	/* Floppy DMA Pointer */
+#define IO_REG_ISDN_T_DMA_P	0x80	/* ISDN Transmit DMA Pointer */
+#define IO_REG_ISDN_T_DMA_BP	0x90	/* ISDN Transmit DMA Buffer Pointer */
+#define IO_REG_ISDN_R_DMA_P	0xa0	/* ISDN Receive DMA Pointer */
+#define IO_REG_ISDN_R_DMA_BP	0xb0	/* ISDN Receive DMA Buffer Pointer */
+
+					/* all systems */
+#define IO_REG_DATA_0		0xc0	/* System Data Buffer 0 */
+#define IO_REG_DATA_1		0xd0	/* System Data Buffer 1 */
+#define IO_REG_DATA_2		0xe0	/* System Data Buffer 2 */
+#define IO_REG_DATA_3		0xf0	/* System Data Buffer 3 */
+
+					/* all systems */
+#define IO_REG_SSR		0x100	/* System Support Register */
+#define IO_REG_SIR		0x110	/* System Interrupt Register */
+#define IO_REG_SIMR		0x120	/* System Interrupt Mask Reg. */
+#define IO_REG_SAR		0x130	/* System Address Register */
+
+					/* Maxine */
+#define IO_REG_ISDN_T_DATA	0x140	/* ISDN Xmit Data Register */
+#define IO_REG_ISDN_R_DATA	0x150	/* ISDN Receive Data Register */
+
+					/* all systems */
+#define IO_REG_LANCE_SLOT	0x160	/* LANCE I/O Slot Register */
+#define IO_REG_SCSI_SLOT	0x170	/* SCSI Slot Register */
+#define IO_REG_SCC0A_SLOT	0x180	/* SCC0A DMA Slot Register */
+
+					/* except Maxine */
+#define IO_REG_SCC1A_SLOT	0x190	/* SCC1A DMA Slot Register */
+
+					/* Maxine */
+#define IO_REG_AB_SLOT		0x190	/* ACCESS.bus DMA Slot Register */
+#define IO_REG_FLOPPY_SLOT	0x1a0	/* Floppy Slot Register */
+
+					/* all systems */
+#define IO_REG_SCSI_SCR		0x1b0	/* SCSI Partial-Word DMA Control */
+#define IO_REG_SCSI_SDR0	0x1c0	/* SCSI DMA Partial Word 0 */
+#define IO_REG_SCSI_SDR1	0x1d0	/* SCSI DMA Partial Word 1 */
+#define IO_REG_FCTR		0x1e0	/* Free-Running Counter */
+#define IO_REG_RES_31		0x1f0	/* unused */
+
+
+/*
+ * The upper 16 bits of the System Support Register are a part of the
+ * I/O ASIC's internal DMA engine and thus are common to all I/O ASIC
+ * machines.  The exception is the Maxine, which makes use of the
+ * FLOPPY and ISDN bits (otherwise unused) and has a different SCC
+ * wiring.
+ */
+						/* all systems */
+#define IO_SSR_SCC0A_TX_DMA_EN	(1<<31)		/* SCC0A transmit DMA enable */
+#define IO_SSR_SCC0A_RX_DMA_EN	(1<<30)		/* SCC0A receive DMA enable */
+#define IO_SSR_RES_27		(1<<27)		/* unused */
+#define IO_SSR_RES_26		(1<<26)		/* unused */
+#define IO_SSR_RES_25		(1<<25)		/* unused */
+#define IO_SSR_RES_24		(1<<24)		/* unused */
+#define IO_SSR_RES_23		(1<<23)		/* unused */
+#define IO_SSR_SCSI_DMA_DIR	(1<<18)		/* SCSI DMA direction */
+#define IO_SSR_SCSI_DMA_EN	(1<<17)		/* SCSI DMA enable */
+#define IO_SSR_LANCE_DMA_EN	(1<<16)		/* LANCE DMA enable */
+
+						/* except Maxine */
+#define IO_SSR_SCC1A_TX_DMA_EN	(1<<29)		/* SCC1A transmit DMA enable */
+#define IO_SSR_SCC1A_RX_DMA_EN	(1<<28)		/* SCC1A receive DMA enable */
+#define IO_SSR_RES_22		(1<<22)		/* unused */
+#define IO_SSR_RES_21		(1<<21)		/* unused */
+#define IO_SSR_RES_20		(1<<20)		/* unused */
+#define IO_SSR_RES_19		(1<<19)		/* unused */
+
+						/* Maxine */
+#define IO_SSR_AB_TX_DMA_EN	(1<<29)		/* ACCESS.bus xmit DMA enable */
+#define IO_SSR_AB_RX_DMA_EN	(1<<28)		/* ACCESS.bus recv DMA enable */
+#define IO_SSR_FLOPPY_DMA_DIR	(1<<22)		/* Floppy DMA direction */
+#define IO_SSR_FLOPPY_DMA_EN	(1<<21)		/* Floppy DMA enable */
+#define IO_SSR_ISDN_TX_DMA_EN	(1<<20)		/* ISDN transmit DMA enable */
+#define IO_SSR_ISDN_RX_DMA_EN	(1<<19)		/* ISDN receive DMA enable */
+
+/*
+ * The lower 16 bits are system-specific.  Bits 15,11:8 are common and
+ * defined here.  The rest is defined in system-specific headers.
+ */
+#define KN0X_IO_SSR_DIAGDN	(1<<15)		/* diagnostic jumper */
+#define KN0X_IO_SSR_SCC_RST	(1<<11)		/* ~SCC0,1 (Z85C30) reset */
+#define KN0X_IO_SSR_RTC_RST	(1<<10)		/* ~RTC (DS1287) reset */
+#define KN0X_IO_SSR_ASC_RST	(1<<9)		/* ~ASC (NCR53C94) reset */
+#define KN0X_IO_SSR_LANCE_RST	(1<<8)		/* ~LANCE (Am7990) reset */
+
+#endif /* __ASM_MIPS_DEC_IOASIC_ADDRS_H */
diff --git a/arch/mips/include/asm/dec/ioasic_ints.h b/arch/mips/include/asm/dec/ioasic_ints.h
new file mode 100644
index 000000000..9aaa98696
--- /dev/null
+++ b/arch/mips/include/asm/dec/ioasic_ints.h
@@ -0,0 +1,74 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Definitions for the interrupt related bits in the I/O ASIC
+ * interrupt status register (and the interrupt mask register, of course)
+ *
+ * Created with Information from:
+ *
+ * "DEC 3000 300/400/500/600/700/800/900 AXP Models System Programmer's Manual"
+ *
+ * and the Mach Sources
+ *
+ * Copyright (C) 199x  the Anonymous
+ * Copyright (C) 2002  Maciej W. Rozycki
+ */
+
+#ifndef __ASM_DEC_IOASIC_INTS_H
+#define __ASM_DEC_IOASIC_INTS_H
+
+/*
+ * The upper 16 bits are a part of the I/O ASIC's internal DMA engine
+ * and thus are common to all I/O ASIC machines.  The exception is
+ * the Maxine, which makes use of the FLOPPY and ISDN bits (otherwise
+ * unused) and has a different SCC wiring.
+ */
+					/* all systems */
+#define IO_INR_SCC0A_TXDMA	31	/* SCC0A transmit page end */
+#define IO_INR_SCC0A_TXERR	30	/* SCC0A transmit memory read error */
+#define IO_INR_SCC0A_RXDMA	29	/* SCC0A receive half page */
+#define IO_INR_SCC0A_RXERR	28	/* SCC0A receive overrun */
+#define IO_INR_ASC_DMA		19	/* ASC buffer pointer loaded */
+#define IO_INR_ASC_ERR		18	/* ASC page overrun */
+#define IO_INR_ASC_MERR		17	/* ASC memory read error */
+#define IO_INR_LANCE_MERR	16	/* LANCE memory read error */
+
+					/* except Maxine */
+#define IO_INR_SCC1A_TXDMA	27	/* SCC1A transmit page end */
+#define IO_INR_SCC1A_TXERR	26	/* SCC1A transmit memory read error */
+#define IO_INR_SCC1A_RXDMA	25	/* SCC1A receive half page */
+#define IO_INR_SCC1A_RXERR	24	/* SCC1A receive overrun */
+#define IO_INR_RES_23		23	/* unused */
+#define IO_INR_RES_22		22	/* unused */
+#define IO_INR_RES_21		21	/* unused */
+#define IO_INR_RES_20		20	/* unused */
+
+					/* Maxine */
+#define IO_INR_AB_TXDMA		27	/* ACCESS.bus transmit page end */
+#define IO_INR_AB_TXERR		26	/* ACCESS.bus xmit memory read error */
+#define IO_INR_AB_RXDMA		25	/* ACCESS.bus receive half page */
+#define IO_INR_AB_RXERR		24	/* ACCESS.bus receive overrun */
+#define IO_INR_FLOPPY_ERR	23	/* FDC error */
+#define IO_INR_ISDN_TXDMA	22	/* ISDN xmit buffer pointer loaded */
+#define IO_INR_ISDN_RXDMA	21	/* ISDN recv buffer pointer loaded */
+#define IO_INR_ISDN_ERR		20	/* ISDN memory read/overrun error */
+
+#define IO_INR_DMA		16	/* first DMA IRQ */
+
+/*
+ * The lower 16 bits are system-specific and thus defined in
+ * system-specific headers.
+ */
+
+
+#define IO_IRQ_BASE		8	/* first IRQ assigned to I/O ASIC */
+#define IO_IRQ_LINES		32	/* number of I/O ASIC interrupts */
+
+#define IO_IRQ_NR(n)		((n) + IO_IRQ_BASE)
+#define IO_IRQ_MASK(n)		(1 << (n))
+#define IO_IRQ_ALL		0x0000ffff
+#define IO_IRQ_DMA		0xffff0000
+
+#endif /* __ASM_DEC_IOASIC_INTS_H */
diff --git a/arch/mips/include/asm/dec/kn01.h b/arch/mips/include/asm/dec/kn01.h
new file mode 100644
index 000000000..88d9ffd74
--- /dev/null
+++ b/arch/mips/include/asm/dec/kn01.h
@@ -0,0 +1,89 @@
+/*
+ * Hardware info about DECstation DS2100/3100 systems (otherwise known as
+ * pmin/pmax or KN01).
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995,1996 by Paul M. Antoine, some code and definitions
+ * are by courtesy of Chris Fraser.
+ * Copyright (C) 2002, 2003, 2005  Maciej W. Rozycki
+ */
+#ifndef __ASM_MIPS_DEC_KN01_H
+#define __ASM_MIPS_DEC_KN01_H
+
+#define KN01_SLOT_BASE	0x10000000
+#define KN01_SLOT_SIZE	0x01000000
+
+/*
+ * Address ranges for devices.
+ */
+#define KN01_PMASK	(0*KN01_SLOT_SIZE)	/* color plane mask */
+#define KN01_PCC	(1*KN01_SLOT_SIZE)	/* PCC (DC503) cursor */
+#define KN01_VDAC	(2*KN01_SLOT_SIZE)	/* color map */
+#define KN01_RES_3	(3*KN01_SLOT_SIZE)	/* unused */
+#define KN01_RES_4	(4*KN01_SLOT_SIZE)	/* unused */
+#define KN01_RES_5	(5*KN01_SLOT_SIZE)	/* unused */
+#define KN01_RES_6	(6*KN01_SLOT_SIZE)	/* unused */
+#define KN01_ERRADDR	(7*KN01_SLOT_SIZE)	/* write error address */
+#define KN01_LANCE	(8*KN01_SLOT_SIZE)	/* LANCE (Am7990) Ethernet */
+#define KN01_LANCE_MEM	(9*KN01_SLOT_SIZE)	/* LANCE buffer memory */
+#define KN01_SII	(10*KN01_SLOT_SIZE)	/* SII (DC7061) SCSI */
+#define KN01_SII_MEM	(11*KN01_SLOT_SIZE)	/* SII buffer memory */
+#define KN01_DZ11	(12*KN01_SLOT_SIZE)	/* DZ11 (DC7085) serial */
+#define KN01_RTC	(13*KN01_SLOT_SIZE)	/* DS1287 RTC (bytes #0) */
+#define KN01_ESAR	(13*KN01_SLOT_SIZE)	/* MAC address (bytes #1) */
+#define KN01_CSR	(14*KN01_SLOT_SIZE)	/* system ctrl & status reg */
+#define KN01_SYS_ROM	(15*KN01_SLOT_SIZE)	/* system board ROM */
+
+
+/*
+ * Frame buffer memory address.
+ */
+#define KN01_VFB_MEM	0x0fc00000
+
+/*
+ * CPU interrupt bits.
+ */
+#define KN01_CPU_INR_BUS	6	/* memory, I/O bus read/write errors */
+#define KN01_CPU_INR_VIDEO	6	/* PCC area detect #2 */
+#define KN01_CPU_INR_RTC	5	/* DS1287 RTC */
+#define KN01_CPU_INR_DZ11	4	/* DZ11 (DC7085) serial */
+#define KN01_CPU_INR_LANCE	3	/* LANCE (Am7990) Ethernet */
+#define KN01_CPU_INR_SII	2	/* SII (DC7061) SCSI */
+
+
+/*
+ * System Control & Status Register bits.
+ */
+#define KN01_CSR_MNFMOD		(1<<15)	/* MNFMOD manufacturing jumper */
+#define KN01_CSR_STATUS		(1<<14)	/* self-test result status output */
+#define KN01_CSR_PARDIS		(1<<13)	/* parity error disable */
+#define KN01_CSR_CRSRTST	(1<<12)	/* PCC test output */
+#define KN01_CSR_MONO		(1<<11)	/* mono/color fb SIMM installed */
+#define KN01_CSR_MEMERR		(1<<10)	/* write timeout error status & ack*/
+#define KN01_CSR_VINT		(1<<9)	/* PCC area detect #2 status & ack */
+#define KN01_CSR_TXDIS		(1<<8)	/* DZ11 transmit disable */
+#define KN01_CSR_VBGTRG		(1<<2)	/* blue DAC voltage over green (r/o) */
+#define KN01_CSR_VRGTRG		(1<<1)	/* red DAC voltage over green (r/o) */
+#define KN01_CSR_VRGTRB		(1<<0)	/* red DAC voltage over blue (r/o) */
+#define KN01_CSR_LEDS		(0xff<<0) /* ~diagnostic LEDs (w/o) */
+
+
+#ifndef __ASSEMBLY__
+
+#include <linux/interrupt.h>
+#include <linux/spinlock.h>
+#include <linux/types.h>
+
+struct pt_regs;
+
+extern u16 cached_kn01_csr;
+
+extern void dec_kn01_be_init(void);
+extern int dec_kn01_be_handler(struct pt_regs *regs, int is_fixup);
+extern irqreturn_t dec_kn01_be_interrupt(int irq, void *dev_id);
+#endif
+
+#endif /* __ASM_MIPS_DEC_KN01_H */
diff --git a/arch/mips/include/asm/dec/kn02.h b/arch/mips/include/asm/dec/kn02.h
new file mode 100644
index 000000000..93430b5f4
--- /dev/null
+++ b/arch/mips/include/asm/dec/kn02.h
@@ -0,0 +1,91 @@
+/*
+ * Hardware info about DECstation 5000/200 systems (otherwise known as
+ * 3max or KN02).
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995,1996 by Paul M. Antoine, some code and definitions
+ * are by courtesy of Chris Fraser.
+ * Copyright (C) 2002, 2003, 2005  Maciej W. Rozycki
+ */
+#ifndef __ASM_MIPS_DEC_KN02_H
+#define __ASM_MIPS_DEC_KN02_H
+
+#define KN02_SLOT_BASE	0x1fc00000
+#define KN02_SLOT_SIZE	0x00080000
+
+/*
+ * Address ranges decoded by the "system slot" logic for onboard devices.
+ */
+#define KN02_SYS_ROM	(0*KN02_SLOT_SIZE)	/* system board ROM */
+#define KN02_RES_1	(1*KN02_SLOT_SIZE)	/* unused */
+#define KN02_CHKSYN	(2*KN02_SLOT_SIZE)	/* ECC syndrome */
+#define KN02_ERRADDR	(3*KN02_SLOT_SIZE)	/* bus error address */
+#define KN02_DZ11	(4*KN02_SLOT_SIZE)	/* DZ11 (DC7085) serial */
+#define KN02_RTC	(5*KN02_SLOT_SIZE)	/* DS1287 RTC */
+#define KN02_CSR	(6*KN02_SLOT_SIZE)	/* system ctrl & status reg */
+#define KN02_SYS_ROM_7	(7*KN02_SLOT_SIZE)	/* system board ROM (alias) */
+
+
+/*
+ * System Control & Status Register bits.
+ */
+#define KN02_CSR_RES_28		(0xf<<28)	/* unused */
+#define KN02_CSR_PSU		(1<<27)		/* power supply unit warning */
+#define KN02_CSR_NVRAM		(1<<26)		/* ~NVRAM clear jumper */
+#define KN02_CSR_REFEVEN	(1<<25)		/* mem refresh bank toggle */
+#define KN02_CSR_NRMOD		(1<<24)		/* ~NRMOD manufact. jumper */
+#define KN02_CSR_IOINTEN	(0xff<<16)	/* IRQ mask bits */
+#define KN02_CSR_DIAGCHK	(1<<15)		/* diagn/norml ECC reads */
+#define KN02_CSR_DIAGGEN	(1<<14)		/* diagn/norml ECC writes */
+#define KN02_CSR_CORRECT	(1<<13)		/* ECC correct/check */
+#define KN02_CSR_LEDIAG		(1<<12)		/* ECC diagn. latch strobe */
+#define KN02_CSR_TXDIS		(1<<11)		/* DZ11 transmit disable */
+#define KN02_CSR_BNK32M		(1<<10)		/* 32M/8M stride */
+#define KN02_CSR_DIAGDN		(1<<9)		/* DIAGDN manufact. jumper */
+#define KN02_CSR_BAUD38		(1<<8)		/* DZ11 38/19kbps ext. rate */
+#define KN02_CSR_IOINT		(0xff<<0)	/* IRQ status bits (r/o) */
+#define KN02_CSR_LEDS		(0xff<<0)	/* ~diagnostic LEDs (w/o) */
+
+
+/*
+ * CPU interrupt bits.
+ */
+#define KN02_CPU_INR_RES_6	6	/* unused */
+#define KN02_CPU_INR_BUS	5	/* memory, I/O bus read/write errors */
+#define KN02_CPU_INR_RES_4	4	/* unused */
+#define KN02_CPU_INR_RTC	3	/* DS1287 RTC */
+#define KN02_CPU_INR_CASCADE	2	/* CSR cascade */
+
+/*
+ * CSR interrupt bits.
+ */
+#define KN02_CSR_INR_DZ11	7	/* DZ11 (DC7085) serial */
+#define KN02_CSR_INR_LANCE	6	/* LANCE (Am7990) Ethernet */
+#define KN02_CSR_INR_ASC	5	/* ASC (NCR53C94) SCSI */
+#define KN02_CSR_INR_RES_4	4	/* unused */
+#define KN02_CSR_INR_RES_3	3	/* unused */
+#define KN02_CSR_INR_TC2	2	/* TURBOchannel slot #2 */
+#define KN02_CSR_INR_TC1	1	/* TURBOchannel slot #1 */
+#define KN02_CSR_INR_TC0	0	/* TURBOchannel slot #0 */
+
+
+#define KN02_IRQ_BASE		8	/* first IRQ assigned to CSR */
+#define KN02_IRQ_LINES		8	/* number of CSR interrupts */
+
+#define KN02_IRQ_NR(n)		((n) + KN02_IRQ_BASE)
+#define KN02_IRQ_MASK(n)	(1 << (n))
+#define KN02_IRQ_ALL		0xff
+
+
+#ifndef __ASSEMBLY__
+
+#include <linux/types.h>
+
+extern u32 cached_kn02_csr;
+extern void init_kn02_irqs(int base);
+#endif
+
+#endif /* __ASM_MIPS_DEC_KN02_H */
diff --git a/arch/mips/include/asm/dec/kn02ba.h b/arch/mips/include/asm/dec/kn02ba.h
new file mode 100644
index 000000000..81a6cc1c5
--- /dev/null
+++ b/arch/mips/include/asm/dec/kn02ba.h
@@ -0,0 +1,63 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ *	include/asm-mips/dec/kn02ba.h
+ *
+ *	DECstation 5000/1xx (3min or KN02-BA) definitions.
+ *
+ *	Copyright (C) 2002, 2003  Maciej W. Rozycki
+ */
+#ifndef __ASM_MIPS_DEC_KN02BA_H
+#define __ASM_MIPS_DEC_KN02BA_H
+
+#include <asm/dec/kn02xa.h>		/* For common definitions. */
+
+/*
+ * CPU interrupt bits.
+ */
+#define KN02BA_CPU_INR_HALT	6	/* HALT button */
+#define KN02BA_CPU_INR_CASCADE	5	/* I/O ASIC cascade */
+#define KN02BA_CPU_INR_TC2	4	/* TURBOchannel slot #2 */
+#define KN02BA_CPU_INR_TC1	3	/* TURBOchannel slot #1 */
+#define KN02BA_CPU_INR_TC0	2	/* TURBOchannel slot #0 */
+
+/*
+ * I/O ASIC interrupt bits.  Star marks denote non-IRQ status bits.
+ */
+#define KN02BA_IO_INR_RES_15	15	/* unused */
+#define KN02BA_IO_INR_NVRAM	14	/* (*) NVRAM clear jumper */
+#define KN02BA_IO_INR_RES_13	13	/* unused */
+#define KN02BA_IO_INR_BUS	12	/* memory, I/O bus read/write errors */
+#define KN02BA_IO_INR_RES_11	11	/* unused */
+#define KN02BA_IO_INR_NRMOD	10	/* (*) NRMOD manufacturing jumper */
+#define KN02BA_IO_INR_ASC	9	/* ASC (NCR53C94) SCSI */
+#define KN02BA_IO_INR_LANCE	8	/* LANCE (Am7990) Ethernet */
+#define KN02BA_IO_INR_SCC1	7	/* SCC (Z85C30) serial #1 */
+#define KN02BA_IO_INR_SCC0	6	/* SCC (Z85C30) serial #0 */
+#define KN02BA_IO_INR_RTC	5	/* DS1287 RTC */
+#define KN02BA_IO_INR_PSU	4	/* power supply unit warning */
+#define KN02BA_IO_INR_RES_3	3	/* unused */
+#define KN02BA_IO_INR_ASC_DATA	2	/* SCSI data ready (for PIO) */
+#define KN02BA_IO_INR_PBNC	1	/* ~HALT button debouncer */
+#define KN02BA_IO_INR_PBNO	0	/* HALT button debouncer */
+
+
+/*
+ * Memory Error Register bits.
+ */
+#define KN02BA_MER_RES_27	(1<<27)		/* unused */
+
+/*
+ * Memory Size Register bits.
+ */
+#define KN02BA_MSR_RES_17	(0x3ff<<17)	/* unused */
+
+/*
+ * I/O ASIC System Support Register bits.
+ */
+#define KN02BA_IO_SSR_TXDIS1	(1<<14)		/* SCC1 transmit disable */
+#define KN02BA_IO_SSR_TXDIS0	(1<<13)		/* SCC0 transmit disable */
+#define KN02BA_IO_SSR_RES_12	(1<<12)		/* unused */
+
+#define KN02BA_IO_SSR_LEDS	(0xff<<0)	/* ~diagnostic LEDs */
+
+#endif /* __ASM_MIPS_DEC_KN02BA_H */
diff --git a/arch/mips/include/asm/dec/kn02ca.h b/arch/mips/include/asm/dec/kn02ca.h
new file mode 100644
index 000000000..a466101eb
--- /dev/null
+++ b/arch/mips/include/asm/dec/kn02ca.h
@@ -0,0 +1,75 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ *	include/asm-mips/dec/kn02ca.h
+ *
+ *	Personal DECstation 5000/xx (Maxine or KN02-CA) definitions.
+ *
+ *	Copyright (C) 2002, 2003  Maciej W. Rozycki
+ */
+#ifndef __ASM_MIPS_DEC_KN02CA_H
+#define __ASM_MIPS_DEC_KN02CA_H
+
+#include <asm/dec/kn02xa.h>		/* For common definitions. */
+
+/*
+ * CPU interrupt bits.
+ */
+#define KN02CA_CPU_INR_HALT	6	/* HALT from ACCESS.Bus */
+#define KN02CA_CPU_INR_CASCADE	5	/* I/O ASIC cascade */
+#define KN02CA_CPU_INR_BUS	4	/* memory, I/O bus read/write errors */
+#define KN02CA_CPU_INR_RTC	3	/* DS1287 RTC */
+#define KN02CA_CPU_INR_TIMER	2	/* ARC periodic timer */
+
+/*
+ * I/O ASIC interrupt bits.  Star marks denote non-IRQ status bits.
+ */
+#define KN02CA_IO_INR_FLOPPY	15	/* 82077 FDC */
+#define KN02CA_IO_INR_NVRAM	14	/* (*) NVRAM clear jumper */
+#define KN02CA_IO_INR_POWERON	13	/* (*) ACCESS.Bus/power-on reset */
+#define KN02CA_IO_INR_TC0	12	/* TURBOchannel slot #0 */
+#define KN02CA_IO_INR_TIMER	12	/* ARC periodic timer (?) */
+#define KN02CA_IO_INR_ISDN	11	/* Am79C30A ISDN */
+#define KN02CA_IO_INR_NRMOD	10	/* (*) NRMOD manufacturing jumper */
+#define KN02CA_IO_INR_ASC	9	/* ASC (NCR53C94) SCSI */
+#define KN02CA_IO_INR_LANCE	8	/* LANCE (Am7990) Ethernet */
+#define KN02CA_IO_INR_HDFLOPPY	7	/* (*) HD (1.44MB) floppy status */
+#define KN02CA_IO_INR_SCC0	6	/* SCC (Z85C30) serial #0 */
+#define KN02CA_IO_INR_TC1	5	/* TURBOchannel slot #1 */
+#define KN02CA_IO_INR_XDFLOPPY	4	/* (*) XD (2.88MB) floppy status */
+#define KN02CA_IO_INR_VIDEO	3	/* framebuffer */
+#define KN02CA_IO_INR_XVIDEO	2	/* ~framebuffer */
+#define KN02CA_IO_INR_AB_XMIT	1	/* ACCESS.bus transmit */
+#define KN02CA_IO_INR_AB_RECV	0	/* ACCESS.bus receive */
+
+
+/*
+ * Memory Error Register bits.
+ */
+#define KN02CA_MER_INTR		(1<<27)		/* ARC IRQ status & ack */
+
+/*
+ * Memory Size Register bits.
+ */
+#define KN02CA_MSR_INTREN	(1<<26)		/* ARC periodic IRQ enable */
+#define KN02CA_MSR_MS10EN	(1<<25)		/* 10/1ms IRQ period select */
+#define KN02CA_MSR_PFORCE	(0xf<<21)	/* byte lane error force */
+#define KN02CA_MSR_MABEN	(1<<20)		/* A side VFB address enable */
+#define KN02CA_MSR_LASTBANK	(0x7<<17)	/* onboard RAM bank # */
+
+/*
+ * I/O ASIC System Support Register bits.
+ */
+#define KN03CA_IO_SSR_RES_14	(1<<14)		/* unused */
+#define KN03CA_IO_SSR_RES_13	(1<<13)		/* unused */
+#define KN03CA_IO_SSR_ISDN_RST	(1<<12)		/* ~ISDN (Am79C30A) reset */
+
+#define KN03CA_IO_SSR_FLOPPY_RST (1<<7)		/* ~FDC (82077) reset */
+#define KN03CA_IO_SSR_VIDEO_RST	(1<<6)		/* ~framebuffer reset */
+#define KN03CA_IO_SSR_AB_RST	(1<<5)		/* ACCESS.bus reset */
+#define KN03CA_IO_SSR_RES_4	(1<<4)		/* unused */
+#define KN03CA_IO_SSR_RES_3	(1<<4)		/* unused */
+#define KN03CA_IO_SSR_RES_2	(1<<2)		/* unused */
+#define KN03CA_IO_SSR_RES_1	(1<<1)		/* unused */
+#define KN03CA_IO_SSR_LED	(1<<0)		/* power LED */
+
+#endif /* __ASM_MIPS_DEC_KN02CA_H */
diff --git a/arch/mips/include/asm/dec/kn02xa.h b/arch/mips/include/asm/dec/kn02xa.h
new file mode 100644
index 000000000..b56b4577f
--- /dev/null
+++ b/arch/mips/include/asm/dec/kn02xa.h
@@ -0,0 +1,84 @@
+/*
+ * Hardware info common to DECstation 5000/1xx systems (otherwise
+ * known as 3min or kn02ba) and Personal DECstations 5000/xx ones
+ * (otherwise known as maxine or kn02ca).
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995,1996 by Paul M. Antoine, some code and definitions
+ * are by courtesy of Chris Fraser.
+ * Copyright (C) 2000, 2002, 2003, 2005  Maciej W. Rozycki
+ *
+ * These are addresses which have to be known early in the boot process.
+ * For other addresses refer to tc.h, ioasic_addrs.h and friends.
+ */
+#ifndef __ASM_MIPS_DEC_KN02XA_H
+#define __ASM_MIPS_DEC_KN02XA_H
+
+#include <asm/dec/ioasic_addrs.h>
+
+#define KN02XA_SLOT_BASE	0x1c000000
+
+/*
+ * Memory control ASIC registers.
+ */
+#define KN02XA_MER		0x0c400000	/* memory error register */
+#define KN02XA_MSR		0x0c800000	/* memory size register */
+
+/*
+ * CPU control ASIC registers.
+ */
+#define KN02XA_MEM_CONF		0x0e000000	/* write timeout config */
+#define KN02XA_EAR		0x0e000004	/* error address register */
+#define KN02XA_BOOT0		0x0e000008	/* boot 0 register */
+#define KN02XA_MEM_INTR		0x0e00000c	/* write err IRQ stat & ack */
+
+/*
+ * Memory Error Register bits, common definitions.
+ * The rest is defined in system-specific headers.
+ */
+#define KN02XA_MER_RES_28	(0xf<<28)	/* unused */
+#define KN02XA_MER_RES_17	(0x3ff<<17)	/* unused */
+#define KN02XA_MER_PAGERR	(1<<16)		/* 2k page boundary error */
+#define KN02XA_MER_TRANSERR	(1<<15)		/* transfer length error */
+#define KN02XA_MER_PARDIS	(1<<14)		/* parity error disable */
+#define KN02XA_MER_SIZE		(1<<13)		/* r/o mirror of MSR_SIZE */
+#define KN02XA_MER_RES_12	(1<<12)		/* unused */
+#define KN02XA_MER_BYTERR	(0xf<<8)	/* byte lane error bitmask: */
+#define KN02XA_MER_BYTERR_3	(0x8<<8)	/* byte lane #3 */
+#define KN02XA_MER_BYTERR_2	(0x4<<8)	/* byte lane #2 */
+#define KN02XA_MER_BYTERR_1	(0x2<<8)	/* byte lane #1 */
+#define KN02XA_MER_BYTERR_0	(0x1<<8)	/* byte lane #0 */
+#define KN02XA_MER_RES_0	(0xff<<0)	/* unused */
+
+/*
+ * Memory Size Register bits, common definitions.
+ * The rest is defined in system-specific headers.
+ */
+#define KN02XA_MSR_RES_27	(0x1f<<27)	/* unused */
+#define KN02XA_MSR_RES_14	(0x7<<14)	/* unused */
+#define KN02XA_MSR_SIZE		(1<<13)		/* 16M/4M stride */
+#define KN02XA_MSR_RES_0	(0x1fff<<0)	/* unused */
+
+/*
+ * Error Address Register bits.
+ */
+#define KN02XA_EAR_RES_29	(0x7<<29)	/* unused */
+#define KN02XA_EAR_ADDRESS	(0x7ffffff<<2)	/* address involved */
+#define KN02XA_EAR_RES_0	(0x3<<0)	/* unused */
+
+
+#ifndef __ASSEMBLY__
+
+#include <linux/interrupt.h>
+
+struct pt_regs;
+
+extern void dec_kn02xa_be_init(void);
+extern int dec_kn02xa_be_handler(struct pt_regs *regs, int is_fixup);
+extern irqreturn_t dec_kn02xa_be_interrupt(int irq, void *dev_id);
+#endif
+
+#endif /* __ASM_MIPS_DEC_KN02XA_H */
diff --git a/arch/mips/include/asm/dec/kn03.h b/arch/mips/include/asm/dec/kn03.h
new file mode 100644
index 000000000..edede923f
--- /dev/null
+++ b/arch/mips/include/asm/dec/kn03.h
@@ -0,0 +1,74 @@
+/*
+ * Hardware info about DECstation 5000/2x0 systems (otherwise known as
+ * 3max+) and DECsystem 5900 systems (otherwise known as bigmax) which
+ * differ mechanically but are otherwise identical (both are known as
+ * KN03).
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995,1996 by Paul M. Antoine, some code and definitions
+ * are by courtesy of Chris Fraser.
+ * Copyright (C) 2000, 2002, 2003, 2005  Maciej W. Rozycki
+ */
+#ifndef __ASM_MIPS_DEC_KN03_H
+#define __ASM_MIPS_DEC_KN03_H
+
+#include <asm/dec/ecc.h>
+#include <asm/dec/ioasic_addrs.h>
+
+#define KN03_SLOT_BASE		0x1f800000
+
+/*
+ * CPU interrupt bits.
+ */
+#define KN03_CPU_INR_HALT	6	/* HALT button */
+#define KN03_CPU_INR_BUS	5	/* memory, I/O bus read/write errors */
+#define KN03_CPU_INR_RES_4	4	/* unused */
+#define KN03_CPU_INR_RTC	3	/* DS1287 RTC */
+#define KN03_CPU_INR_CASCADE	2	/* I/O ASIC cascade */
+
+/*
+ * I/O ASIC interrupt bits.  Star marks denote non-IRQ status bits.
+ */
+#define KN03_IO_INR_3MAXP	15	/* (*) 3max+/bigmax ID */
+#define KN03_IO_INR_NVRAM	14	/* (*) NVRAM clear jumper */
+#define KN03_IO_INR_TC2		13	/* TURBOchannel slot #2 */
+#define KN03_IO_INR_TC1		12	/* TURBOchannel slot #1 */
+#define KN03_IO_INR_TC0		11	/* TURBOchannel slot #0 */
+#define KN03_IO_INR_NRMOD	10	/* (*) NRMOD manufacturing jumper */
+#define KN03_IO_INR_ASC		9	/* ASC (NCR53C94) SCSI */
+#define KN03_IO_INR_LANCE	8	/* LANCE (Am7990) Ethernet */
+#define KN03_IO_INR_SCC1	7	/* SCC (Z85C30) serial #1 */
+#define KN03_IO_INR_SCC0	6	/* SCC (Z85C30) serial #0 */
+#define KN03_IO_INR_RTC		5	/* DS1287 RTC */
+#define KN03_IO_INR_PSU		4	/* power supply unit warning */
+#define KN03_IO_INR_RES_3	3	/* unused */
+#define KN03_IO_INR_ASC_DATA	2	/* SCSI data ready (for PIO) */
+#define KN03_IO_INR_PBNC	1	/* ~HALT button debouncer */
+#define KN03_IO_INR_PBNO	0	/* HALT button debouncer */
+
+
+/*
+ * Memory Control Register bits.
+ */
+#define KN03_MCR_RES_16		(0xffff<<16)	/* unused */
+#define KN03_MCR_DIAGCHK	(1<<15)		/* diagn/norml ECC reads */
+#define KN03_MCR_DIAGGEN	(1<<14)		/* diagn/norml ECC writes */
+#define KN03_MCR_CORRECT	(1<<13)		/* ECC correct/check */
+#define KN03_MCR_RES_11		(0x3<<12)	/* unused */
+#define KN03_MCR_BNK32M		(1<<10)		/* 32M/8M stride */
+#define KN03_MCR_RES_7		(0x7<<7)	/* unused */
+#define KN03_MCR_CHECK		(0x7f<<0)	/* diagnostic check bits */
+
+/*
+ * I/O ASIC System Support Register bits.
+ */
+#define KN03_IO_SSR_TXDIS1	(1<<14)		/* SCC1 transmit disable */
+#define KN03_IO_SSR_TXDIS0	(1<<13)		/* SCC0 transmit disable */
+#define KN03_IO_SSR_RES_12	(1<<12)		/* unused */
+
+#define KN03_IO_SSR_LEDS	(0xff<<0)	/* ~diagnostic LEDs */
+
+#endif /* __ASM_MIPS_DEC_KN03_H */
diff --git a/arch/mips/include/asm/dec/kn05.h b/arch/mips/include/asm/dec/kn05.h
new file mode 100644
index 000000000..3b1524e9f
--- /dev/null
+++ b/arch/mips/include/asm/dec/kn05.h
@@ -0,0 +1,81 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ *	include/asm-mips/dec/kn05.h
+ *
+ *	DECstation/DECsystem 5000/260 (4max+ or KN05), 5000/150 (4min
+ *	or KN04-BA), Personal DECstation/DECsystem 5000/50 (4maxine or
+ *	KN04-CA) and DECsystem 5900/260 (KN05) R4k CPU card MB ASIC
+ *	definitions.
+ *
+ *	Copyright (C) 2002, 2003, 2005, 2008  Maciej W. Rozycki
+ *
+ *	WARNING!  All this information is pure guesswork based on the
+ *	ROM.  It is provided here in hope it will give someone some
+ *	food for thought.  No documentation for the KN05 nor the KN04
+ *	module has been located so far.
+ */
+#ifndef __ASM_MIPS_DEC_KN05_H
+#define __ASM_MIPS_DEC_KN05_H
+
+#include <asm/dec/ioasic_addrs.h>
+
+/*
+ * The oncard MB (Memory Buffer) ASIC provides an additional address
+ * decoder.  Certain address ranges within the "high" 16 slots are
+ * passed to the I/O ASIC's decoder like with the KN03 or KN02-BA/CA.
+ * Others are handled locally.  "Low" slots are always passed.
+ */
+#define KN4K_SLOT_BASE	0x1fc00000
+
+#define KN4K_MB_ROM	(0*IOASIC_SLOT_SIZE)	/* KN05/KN04 card ROM */
+#define KN4K_IOCTL	(1*IOASIC_SLOT_SIZE)	/* I/O ASIC */
+#define KN4K_ESAR	(2*IOASIC_SLOT_SIZE)	/* LANCE MAC address chip */
+#define KN4K_LANCE	(3*IOASIC_SLOT_SIZE)	/* LANCE Ethernet */
+#define KN4K_MB_INT	(4*IOASIC_SLOT_SIZE)	/* MB interrupt register */
+#define KN4K_MB_EA	(5*IOASIC_SLOT_SIZE)	/* MB error address? */
+#define KN4K_MB_EC	(6*IOASIC_SLOT_SIZE)	/* MB error ??? */
+#define KN4K_MB_CSR	(7*IOASIC_SLOT_SIZE)	/* MB control & status */
+#define KN4K_RES_08	(8*IOASIC_SLOT_SIZE)	/* unused? */
+#define KN4K_RES_09	(9*IOASIC_SLOT_SIZE)	/* unused? */
+#define KN4K_RES_10	(10*IOASIC_SLOT_SIZE)	/* unused? */
+#define KN4K_RES_11	(11*IOASIC_SLOT_SIZE)	/* unused? */
+#define KN4K_SCSI	(12*IOASIC_SLOT_SIZE)	/* ASC SCSI */
+#define KN4K_RES_13	(13*IOASIC_SLOT_SIZE)	/* unused? */
+#define KN4K_RES_14	(14*IOASIC_SLOT_SIZE)	/* unused? */
+#define KN4K_RES_15	(15*IOASIC_SLOT_SIZE)	/* unused? */
+
+/*
+ * MB ASIC interrupt bits.
+ */
+#define KN4K_MB_INR_MB		4	/* ??? */
+#define KN4K_MB_INR_MT		3	/* memory, I/O bus read/write errors */
+#define KN4K_MB_INR_RES_2	2	/* unused */
+#define KN4K_MB_INR_RTC		1	/* RTC */
+#define KN4K_MB_INR_TC		0	/* I/O ASIC cascade */
+
+/*
+ * Bits for the MB interrupt register.
+ * The register appears read-only.
+ */
+#define KN4K_MB_INT_IRQ		(0x1f<<0)	/* CPU Int[4:0] status. */
+#define KN4K_MB_INT_IRQ_N(n)	(1<<(n))	/* Individual status bits. */
+
+/*
+ * Bits for the MB control & status register.
+ * Set to 0x00bf8001 for KN05 and to 0x003f8000 for KN04 by the firmware.
+ */
+#define KN4K_MB_CSR_PF		(1<<0)		/* PreFetching enable? */
+#define KN4K_MB_CSR_F		(1<<1)		/* ??? */
+#define KN4K_MB_CSR_ECC		(0xff<<2)	/* ??? */
+#define KN4K_MB_CSR_OD		(1<<10)		/* ??? */
+#define KN4K_MB_CSR_CP		(1<<11)		/* ??? */
+#define KN4K_MB_CSR_UNC		(1<<12)		/* ??? */
+#define KN4K_MB_CSR_IM		(1<<13)		/* ??? */
+#define KN4K_MB_CSR_NC		(1<<14)		/* ??? */
+#define KN4K_MB_CSR_EE		(1<<15)		/* (bus) Exception Enable? */
+#define KN4K_MB_CSR_MSK		(0x1f<<16)	/* CPU Int[4:0] mask */
+#define KN4K_MB_CSR_MSK_N(n)	(1<<((n)+16))	/* Individual mask bits. */
+#define KN4K_MB_CSR_FW		(1<<21)		/* ??? */
+#define KN4K_MB_CSR_W		(1<<31)		/* ??? */
+
+#endif /* __ASM_MIPS_DEC_KN05_H */
diff --git a/arch/mips/include/asm/dec/kn230.h b/arch/mips/include/asm/dec/kn230.h
new file mode 100644
index 000000000..cb13a7799
--- /dev/null
+++ b/arch/mips/include/asm/dec/kn230.h
@@ -0,0 +1,22 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ *	include/asm-mips/dec/kn230.h
+ *
+ *	DECsystem 5100 (MIPSmate or KN230) definitions.
+ *
+ *	Copyright (C) 2002, 2003  Maciej W. Rozycki
+ */
+#ifndef __ASM_MIPS_DEC_KN230_H
+#define __ASM_MIPS_DEC_KN230_H
+
+/*
+ * CPU interrupt bits.
+ */
+#define KN230_CPU_INR_HALT	6	/* HALT button */
+#define KN230_CPU_INR_BUS	5	/* memory, I/O bus read/write errors */
+#define KN230_CPU_INR_RTC	4	/* DS1287 RTC */
+#define KN230_CPU_INR_SII	3	/* SII (DC7061) SCSI */
+#define KN230_CPU_INR_LANCE	3	/* LANCE (Am7990) Ethernet */
+#define KN230_CPU_INR_DZ11	2	/* DZ11 (DC7085) serial */
+
+#endif /* __ASM_MIPS_DEC_KN230_H */
diff --git a/arch/mips/include/asm/dec/machtype.h b/arch/mips/include/asm/dec/machtype.h
new file mode 100644
index 000000000..a6ecdebc4
--- /dev/null
+++ b/arch/mips/include/asm/dec/machtype.h
@@ -0,0 +1,27 @@
+/*
+ * Various machine type macros
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (c) 1998, 2000 Harald Koerfgen
+ */
+
+#ifndef __ASM_DEC_MACHTYPE_H
+#define __ASM_DEC_MACHTYPE_H
+
+#include <asm/bootinfo.h>
+
+#define TURBOCHANNEL	(mips_machtype == MACH_DS5000_200 || \
+			 mips_machtype == MACH_DS5000_1XX || \
+			 mips_machtype == MACH_DS5000_XX  || \
+			 mips_machtype == MACH_DS5000_2X0 || \
+			 mips_machtype == MACH_DS5900)
+
+#define IOASIC		(mips_machtype == MACH_DS5000_1XX || \
+			 mips_machtype == MACH_DS5000_XX  || \
+			 mips_machtype == MACH_DS5000_2X0 || \
+			 mips_machtype == MACH_DS5900)
+
+#endif
diff --git a/arch/mips/include/asm/dec/prom.h b/arch/mips/include/asm/dec/prom.h
new file mode 100644
index 000000000..908e96e3a
--- /dev/null
+++ b/arch/mips/include/asm/dec/prom.h
@@ -0,0 +1,165 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ *	include/asm-mips/dec/prom.h
+ *
+ *	DECstation PROM interface.
+ *
+ *	Copyright (C) 2002  Maciej W. Rozycki
+ *
+ *	Based on arch/mips/dec/prom/prom.h by the Anonymous.
+ */
+#ifndef _ASM_DEC_PROM_H
+#define _ASM_DEC_PROM_H
+
+#include <linux/types.h>
+
+#include <asm/addrspace.h>
+
+/*
+ * PMAX/3MAX PROM entry points for DS2100/3100's and DS5000/2xx's.
+ * Many of these will work for MIPSen as well!
+ */
+#define VEC_RESET		(u64 *)CKSEG1ADDR(0x1fc00000)
+							/* Prom base address */
+
+#define PMAX_PROM_ENTRY(x)	(VEC_RESET + (x))	/* Prom jump table */
+
+#define PMAX_PROM_HALT		PMAX_PROM_ENTRY(2)	/* valid on MIPSen */
+#define PMAX_PROM_AUTOBOOT	PMAX_PROM_ENTRY(5)	/* valid on MIPSen */
+#define PMAX_PROM_OPEN		PMAX_PROM_ENTRY(6)
+#define PMAX_PROM_READ		PMAX_PROM_ENTRY(7)
+#define PMAX_PROM_CLOSE		PMAX_PROM_ENTRY(10)
+#define PMAX_PROM_LSEEK		PMAX_PROM_ENTRY(11)
+#define PMAX_PROM_GETCHAR	PMAX_PROM_ENTRY(12)
+#define PMAX_PROM_PUTCHAR	PMAX_PROM_ENTRY(13)	/* 12 on MIPSen */
+#define PMAX_PROM_GETS		PMAX_PROM_ENTRY(15)
+#define PMAX_PROM_PRINTF	PMAX_PROM_ENTRY(17)
+#define PMAX_PROM_GETENV	PMAX_PROM_ENTRY(33)	/* valid on MIPSen */
+
+
+/*
+ * Magic number indicating REX PROM available on DECstation.  Found in
+ * register a2 on transfer of control to program from PROM.
+ */
+#define REX_PROM_MAGIC		0x30464354
+
+/* KN04 and KN05 are REX PROMs, so only do the check for R3k systems.  */
+static inline bool prom_is_rex(u32 magic)
+{
+	return !IS_ENABLED(CONFIG_CPU_R3000) || magic == REX_PROM_MAGIC;
+}
+
+/*
+ * 3MIN/MAXINE PROM entry points for DS5000/1xx's, DS5000/xx's and
+ * DS5000/2x0.
+ */
+#define REX_PROM_GETBITMAP	0x84/4	/* get mem bitmap */
+#define REX_PROM_GETCHAR	0x24/4	/* getch() */
+#define REX_PROM_GETENV		0x64/4	/* get env. variable */
+#define REX_PROM_GETSYSID	0x80/4	/* get system id */
+#define REX_PROM_GETTCINFO	0xa4/4
+#define REX_PROM_PRINTF		0x30/4	/* printf() */
+#define REX_PROM_SLOTADDR	0x6c/4	/* slotaddr */
+#define REX_PROM_BOOTINIT	0x54/4	/* open() */
+#define REX_PROM_BOOTREAD	0x58/4	/* read() */
+#define REX_PROM_CLEARCACHE	0x7c/4
+
+
+/*
+ * Used by rex_getbitmap().
+ */
+typedef struct {
+	int pagesize;
+	unsigned char bitmap[];
+} memmap;
+
+
+/*
+ * Function pointers as read from a PROM's callback vector.
+ */
+extern int (*__rex_bootinit)(void);
+extern int (*__rex_bootread)(void);
+extern int (*__rex_getbitmap)(memmap *);
+extern unsigned long *(*__rex_slot_address)(int);
+extern void *(*__rex_gettcinfo)(void);
+extern int (*__rex_getsysid)(void);
+extern void (*__rex_clear_cache)(void);
+
+extern int (*__prom_getchar)(void);
+extern char *(*__prom_getenv)(char *);
+extern int (*__prom_printf)(char *, ...);
+
+extern int (*__pmax_open)(char*, int);
+extern int (*__pmax_lseek)(int, long, int);
+extern int (*__pmax_read)(int, void *, int);
+extern int (*__pmax_close)(int);
+
+
+#ifdef CONFIG_64BIT
+
+/*
+ * On MIPS64 we have to call PROM functions via a helper
+ * dispatcher to accommodate ABI incompatibilities.
+ */
+#define __DEC_PROM_O32(fun, arg) fun arg __asm__(#fun); \
+				 __asm__(#fun " = call_o32")
+
+int __DEC_PROM_O32(_rex_bootinit, (int (*)(void), void *));
+int __DEC_PROM_O32(_rex_bootread, (int (*)(void), void *));
+int __DEC_PROM_O32(_rex_getbitmap, (int (*)(memmap *), void *, memmap *));
+unsigned long *__DEC_PROM_O32(_rex_slot_address,
+			     (unsigned long *(*)(int), void *, int));
+void *__DEC_PROM_O32(_rex_gettcinfo, (void *(*)(void), void *));
+int __DEC_PROM_O32(_rex_getsysid, (int (*)(void), void *));
+void __DEC_PROM_O32(_rex_clear_cache, (void (*)(void), void *));
+
+int __DEC_PROM_O32(_prom_getchar, (int (*)(void), void *));
+char *__DEC_PROM_O32(_prom_getenv, (char *(*)(char *), void *, char *));
+int __DEC_PROM_O32(_prom_printf, (int (*)(char *, ...), void *, char *, ...));
+
+
+#define rex_bootinit()		_rex_bootinit(__rex_bootinit, NULL)
+#define rex_bootread()		_rex_bootread(__rex_bootread, NULL)
+#define rex_getbitmap(x)	_rex_getbitmap(__rex_getbitmap, NULL, x)
+#define rex_slot_address(x)	_rex_slot_address(__rex_slot_address, NULL, x)
+#define rex_gettcinfo()		_rex_gettcinfo(__rex_gettcinfo, NULL)
+#define rex_getsysid()		_rex_getsysid(__rex_getsysid, NULL)
+#define rex_clear_cache()	_rex_clear_cache(__rex_clear_cache, NULL)
+
+#define prom_getchar()		_prom_getchar(__prom_getchar, NULL)
+#define prom_getenv(x)		_prom_getenv(__prom_getenv, NULL, x)
+#define prom_printf(x...)	_prom_printf(__prom_printf, NULL, x)
+
+#else /* !CONFIG_64BIT */
+
+/*
+ * On plain MIPS we just call PROM functions directly.
+ */
+#define rex_bootinit		__rex_bootinit
+#define rex_bootread		__rex_bootread
+#define rex_getbitmap		__rex_getbitmap
+#define rex_slot_address	__rex_slot_address
+#define rex_gettcinfo		__rex_gettcinfo
+#define rex_getsysid		__rex_getsysid
+#define rex_clear_cache		__rex_clear_cache
+
+#define prom_getchar		__prom_getchar
+#define prom_getenv		__prom_getenv
+#define prom_printf		__prom_printf
+
+#define pmax_open		__pmax_open
+#define pmax_lseek		__pmax_lseek
+#define pmax_read		__pmax_read
+#define pmax_close		__pmax_close
+
+#endif /* !CONFIG_64BIT */
+
+
+extern void prom_meminit(u32);
+extern void prom_identify_arch(u32);
+extern void prom_init_cmdline(s32, s32 *, u32);
+
+extern void register_prom_console(void);
+extern void unregister_prom_console(void);
+
+#endif /* _ASM_DEC_PROM_H */
diff --git a/arch/mips/include/asm/dec/system.h b/arch/mips/include/asm/dec/system.h
new file mode 100644
index 000000000..d0873fd4e
--- /dev/null
+++ b/arch/mips/include/asm/dec/system.h
@@ -0,0 +1,15 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ *	include/asm-mips/dec/system.h
+ *
+ *	Generic DECstation/DECsystem bits.
+ *
+ *	Copyright (C) 2005, 2006  Maciej W. Rozycki
+ */
+#ifndef __ASM_DEC_SYSTEM_H
+#define __ASM_DEC_SYSTEM_H
+
+extern unsigned long dec_kn_slot_base, dec_kn_slot_size;
+extern int dec_tc_bus;
+
+#endif /* __ASM_DEC_SYSTEM_H */
diff --git a/arch/mips/include/asm/delay.h b/arch/mips/include/asm/delay.h
new file mode 100644
index 000000000..dc0a5f77a
--- /dev/null
+++ b/arch/mips/include/asm/delay.h
@@ -0,0 +1,32 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994 by Waldorf Electronics
+ * Copyright (C) 1995 - 2000, 01, 03 by Ralf Baechle
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ * Copyright (C) 2007  Maciej W. Rozycki
+ */
+#ifndef _ASM_DELAY_H
+#define _ASM_DELAY_H
+
+#include <linux/param.h>
+
+extern void __delay(unsigned long loops);
+extern void __ndelay(unsigned long ns);
+extern void __udelay(unsigned long us);
+
+#define ndelay(ns) __ndelay(ns)
+#define udelay(us) __udelay(us)
+
+/* make sure "usecs *= ..." in udelay do not overflow. */
+#if HZ >= 1000
+#define MAX_UDELAY_MS	1
+#elif HZ <= 200
+#define MAX_UDELAY_MS	5
+#else
+#define MAX_UDELAY_MS	(1000 / HZ)
+#endif
+
+#endif /* _ASM_DELAY_H */
diff --git a/arch/mips/include/asm/div64.h b/arch/mips/include/asm/div64.h
new file mode 100644
index 000000000..ceece76fc
--- /dev/null
+++ b/arch/mips/include/asm/div64.h
@@ -0,0 +1,91 @@
+/*
+ * Copyright (C) 2000, 2004, 2021  Maciej W. Rozycki
+ * Copyright (C) 2003, 07 Ralf Baechle (ralf@linux-mips.org)
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#ifndef __ASM_DIV64_H
+#define __ASM_DIV64_H
+
+#include <asm/bitsperlong.h>
+
+#if BITS_PER_LONG == 32
+
+/*
+ * No traps on overflows for any of these...
+ */
+
+#define do_div64_32(res, high, low, base) ({				\
+	unsigned long __cf, __tmp, __tmp2, __i;				\
+	unsigned long __quot32, __mod32;				\
+									\
+	__asm__(							\
+	"	.set	push					\n"	\
+	"	.set	noat					\n"	\
+	"	.set	noreorder				\n"	\
+	"	move	%2, $0					\n"	\
+	"	move	%3, $0					\n"	\
+	"	b	1f					\n"	\
+	"	 li	%4, 0x21				\n"	\
+	"0:							\n"	\
+	"	sll	$1, %0, 0x1				\n"	\
+	"	srl	%3, %0, 0x1f				\n"	\
+	"	or	%0, $1, %5				\n"	\
+	"	sll	%1, %1, 0x1				\n"	\
+	"	sll	%2, %2, 0x1				\n"	\
+	"1:							\n"	\
+	"	bnez	%3, 2f					\n"	\
+	"	 sltu	%5, %0, %z6				\n"	\
+	"	bnez	%5, 3f					\n"	\
+	"2:							\n"	\
+	"	 addiu	%4, %4, -1				\n"	\
+	"	subu	%0, %0, %z6				\n"	\
+	"	addiu	%2, %2, 1				\n"	\
+	"3:							\n"	\
+	"	bnez	%4, 0b					\n"	\
+	"	 srl	%5, %1, 0x1f				\n"	\
+	"	.set	pop"						\
+	: "=&r" (__mod32), "=&r" (__tmp),				\
+	  "=&r" (__quot32), "=&r" (__cf),				\
+	  "=&r" (__i), "=&r" (__tmp2)					\
+	: "Jr" (base), "0" (high), "1" (low));				\
+									\
+	(res) = __quot32;						\
+	__mod32;							\
+})
+
+#define __div64_32(n, base) ({						\
+	unsigned long __upper, __low, __high, __radix;			\
+	unsigned long long __quot;					\
+	unsigned long long __div;					\
+	unsigned long __mod;						\
+									\
+	__div = (*n);							\
+	__radix = (base);						\
+									\
+	__high = __div >> 32;						\
+	__low = __div;							\
+									\
+	if (__high < __radix) {						\
+		__upper = __high;					\
+		__high = 0;						\
+	} else {							\
+		__upper = __high % __radix;				\
+		__high /= __radix;					\
+	}								\
+									\
+	__mod = do_div64_32(__low, __upper, __low, __radix);		\
+									\
+	__quot = __high;						\
+	__quot = __quot << 32 | __low;					\
+	(*n) = __quot;							\
+	__mod;								\
+})
+
+#endif /* BITS_PER_LONG == 32 */
+
+#include <asm-generic/div64.h>
+
+#endif /* __ASM_DIV64_H */
diff --git a/arch/mips/include/asm/dma-direct.h b/arch/mips/include/asm/dma-direct.h
new file mode 100644
index 000000000..9a6401183
--- /dev/null
+++ b/arch/mips/include/asm/dma-direct.h
@@ -0,0 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _MIPS_DMA_DIRECT_H
+#define _MIPS_DMA_DIRECT_H 1
+
+dma_addr_t phys_to_dma(struct device *dev, phys_addr_t paddr);
+phys_addr_t dma_to_phys(struct device *dev, dma_addr_t daddr);
+
+#endif /* _MIPS_DMA_DIRECT_H */
diff --git a/arch/mips/include/asm/dma-mapping.h b/arch/mips/include/asm/dma-mapping.h
new file mode 100644
index 000000000..34de7b17b
--- /dev/null
+++ b/arch/mips/include/asm/dma-mapping.h
@@ -0,0 +1,18 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _ASM_DMA_MAPPING_H
+#define _ASM_DMA_MAPPING_H
+
+#include <linux/swiotlb.h>
+
+extern const struct dma_map_ops jazz_dma_ops;
+
+static inline const struct dma_map_ops *get_arch_dma_ops(struct bus_type *bus)
+{
+#if defined(CONFIG_MACH_JAZZ)
+	return &jazz_dma_ops;
+#else
+	return NULL;
+#endif
+}
+
+#endif /* _ASM_DMA_MAPPING_H */
diff --git a/arch/mips/include/asm/dma.h b/arch/mips/include/asm/dma.h
new file mode 100644
index 000000000..d6186e6be
--- /dev/null
+++ b/arch/mips/include/asm/dma.h
@@ -0,0 +1,310 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * linux/include/asm/dma.h: Defines for using and allocating dma channels.
+ * Written by Hennus Bergman, 1992.
+ * High DMA channel support & info by Hannu Savolainen
+ * and John Boyd, Nov. 1992.
+ *
+ * NOTE: all this is true *only* for ISA/EISA expansions on Mips boards
+ * and can only be used for expansion cards. Onboard DMA controllers, such
+ * as the R4030 on Jazz boards behave totally different!
+ */
+
+#ifndef _ASM_DMA_H
+#define _ASM_DMA_H
+
+#include <asm/io.h>			/* need byte IO */
+#include <linux/spinlock.h>		/* And spinlocks */
+#include <linux/delay.h>
+
+
+#ifdef HAVE_REALLY_SLOW_DMA_CONTROLLER
+#define dma_outb	outb_p
+#else
+#define dma_outb	outb
+#endif
+
+#define dma_inb		inb
+
+/*
+ * NOTES about DMA transfers:
+ *
+ *  controller 1: channels 0-3, byte operations, ports 00-1F
+ *  controller 2: channels 4-7, word operations, ports C0-DF
+ *
+ *  - ALL registers are 8 bits only, regardless of transfer size
+ *  - channel 4 is not used - cascades 1 into 2.
+ *  - channels 0-3 are byte - addresses/counts are for physical bytes
+ *  - channels 5-7 are word - addresses/counts are for physical words
+ *  - transfers must not cross physical 64K (0-3) or 128K (5-7) boundaries
+ *  - transfer count loaded to registers is 1 less than actual count
+ *  - controller 2 offsets are all even (2x offsets for controller 1)
+ *  - page registers for 5-7 don't use data bit 0, represent 128K pages
+ *  - page registers for 0-3 use bit 0, represent 64K pages
+ *
+ * DMA transfers are limited to the lower 16MB of _physical_ memory.
+ * Note that addresses loaded into registers must be _physical_ addresses,
+ * not logical addresses (which may differ if paging is active).
+ *
+ *  Address mapping for channels 0-3:
+ *
+ *   A23 ... A16 A15 ... A8  A7 ... A0	  (Physical addresses)
+ *    |	 ...  |	  |  ... |   |	... |
+ *    |	 ...  |	  |  ... |   |	... |
+ *    |	 ...  |	  |  ... |   |	... |
+ *   P7	 ...  P0  A7 ... A0  A7 ... A0
+ * |	Page	| Addr MSB | Addr LSB |	  (DMA registers)
+ *
+ *  Address mapping for channels 5-7:
+ *
+ *   A23 ... A17 A16 A15 ... A9 A8 A7 ... A1 A0	   (Physical addresses)
+ *    |	 ...  |	  \   \	  ... \	 \  \  ... \  \
+ *    |	 ...  |	   \   \   ... \  \  \	... \  (not used)
+ *    |	 ...  |	    \	\   ... \  \  \	 ... \
+ *   P7	 ...  P1 (0) A7 A6  ... A0 A7 A6 ... A0
+ * |	  Page	    |  Addr MSB	  |  Addr LSB  |   (DMA registers)
+ *
+ * Again, channels 5-7 transfer _physical_ words (16 bits), so addresses
+ * and counts _must_ be word-aligned (the lowest address bit is _ignored_ at
+ * the hardware level, so odd-byte transfers aren't possible).
+ *
+ * Transfer count (_not # bytes_) is limited to 64K, represented as actual
+ * count - 1 : 64K => 0xFFFF, 1 => 0x0000.  Thus, count is always 1 or more,
+ * and up to 128K bytes may be transferred on channels 5-7 in one operation.
+ *
+ */
+
+#ifndef CONFIG_GENERIC_ISA_DMA_SUPPORT_BROKEN
+#define MAX_DMA_CHANNELS	8
+#endif
+
+/*
+ * The maximum address in KSEG0 that we can perform a DMA transfer to on this
+ * platform.  This describes only the PC style part of the DMA logic like on
+ * Deskstations or Acer PICA but not the much more versatile DMA logic used
+ * for the local devices on Acer PICA or Magnums.
+ */
+#if defined(CONFIG_SGI_IP22) || defined(CONFIG_SGI_IP28)
+/* don't care; ISA bus master won't work, ISA slave DMA supports 32bit addr */
+#define MAX_DMA_ADDRESS		PAGE_OFFSET
+#else
+#define MAX_DMA_ADDRESS		(PAGE_OFFSET + 0x01000000)
+#endif
+#define MAX_DMA_PFN		PFN_DOWN(virt_to_phys((void *)MAX_DMA_ADDRESS))
+
+#ifndef MAX_DMA32_PFN
+#define MAX_DMA32_PFN		(1UL << (32 - PAGE_SHIFT))
+#endif
+
+/* 8237 DMA controllers */
+#define IO_DMA1_BASE	0x00	/* 8 bit slave DMA, channels 0..3 */
+#define IO_DMA2_BASE	0xC0	/* 16 bit master DMA, ch 4(=slave input)..7 */
+
+/* DMA controller registers */
+#define DMA1_CMD_REG		0x08	/* command register (w) */
+#define DMA1_STAT_REG		0x08	/* status register (r) */
+#define DMA1_REQ_REG		0x09	/* request register (w) */
+#define DMA1_MASK_REG		0x0A	/* single-channel mask (w) */
+#define DMA1_MODE_REG		0x0B	/* mode register (w) */
+#define DMA1_CLEAR_FF_REG	0x0C	/* clear pointer flip-flop (w) */
+#define DMA1_TEMP_REG		0x0D	/* Temporary Register (r) */
+#define DMA1_RESET_REG		0x0D	/* Master Clear (w) */
+#define DMA1_CLR_MASK_REG	0x0E	/* Clear Mask */
+#define DMA1_MASK_ALL_REG	0x0F	/* all-channels mask (w) */
+
+#define DMA2_CMD_REG		0xD0	/* command register (w) */
+#define DMA2_STAT_REG		0xD0	/* status register (r) */
+#define DMA2_REQ_REG		0xD2	/* request register (w) */
+#define DMA2_MASK_REG		0xD4	/* single-channel mask (w) */
+#define DMA2_MODE_REG		0xD6	/* mode register (w) */
+#define DMA2_CLEAR_FF_REG	0xD8	/* clear pointer flip-flop (w) */
+#define DMA2_TEMP_REG		0xDA	/* Temporary Register (r) */
+#define DMA2_RESET_REG		0xDA	/* Master Clear (w) */
+#define DMA2_CLR_MASK_REG	0xDC	/* Clear Mask */
+#define DMA2_MASK_ALL_REG	0xDE	/* all-channels mask (w) */
+
+#define DMA_ADDR_0		0x00	/* DMA address registers */
+#define DMA_ADDR_1		0x02
+#define DMA_ADDR_2		0x04
+#define DMA_ADDR_3		0x06
+#define DMA_ADDR_4		0xC0
+#define DMA_ADDR_5		0xC4
+#define DMA_ADDR_6		0xC8
+#define DMA_ADDR_7		0xCC
+
+#define DMA_CNT_0		0x01	/* DMA count registers */
+#define DMA_CNT_1		0x03
+#define DMA_CNT_2		0x05
+#define DMA_CNT_3		0x07
+#define DMA_CNT_4		0xC2
+#define DMA_CNT_5		0xC6
+#define DMA_CNT_6		0xCA
+#define DMA_CNT_7		0xCE
+
+#define DMA_PAGE_0		0x87	/* DMA page registers */
+#define DMA_PAGE_1		0x83
+#define DMA_PAGE_2		0x81
+#define DMA_PAGE_3		0x82
+#define DMA_PAGE_5		0x8B
+#define DMA_PAGE_6		0x89
+#define DMA_PAGE_7		0x8A
+
+#define DMA_MODE_READ	0x44	/* I/O to memory, no autoinit, increment, single mode */
+#define DMA_MODE_WRITE	0x48	/* memory to I/O, no autoinit, increment, single mode */
+#define DMA_MODE_CASCADE 0xC0	/* pass thru DREQ->HRQ, DACK<-HLDA only */
+
+#define DMA_AUTOINIT	0x10
+
+extern spinlock_t  dma_spin_lock;
+
+static __inline__ unsigned long claim_dma_lock(void)
+{
+	unsigned long flags;
+	spin_lock_irqsave(&dma_spin_lock, flags);
+	return flags;
+}
+
+static __inline__ void release_dma_lock(unsigned long flags)
+{
+	spin_unlock_irqrestore(&dma_spin_lock, flags);
+}
+
+/* enable/disable a specific DMA channel */
+static __inline__ void enable_dma(unsigned int dmanr)
+{
+	if (dmanr<=3)
+		dma_outb(dmanr,	 DMA1_MASK_REG);
+	else
+		dma_outb(dmanr & 3,  DMA2_MASK_REG);
+}
+
+static __inline__ void disable_dma(unsigned int dmanr)
+{
+	if (dmanr<=3)
+		dma_outb(dmanr | 4,  DMA1_MASK_REG);
+	else
+		dma_outb((dmanr & 3) | 4,  DMA2_MASK_REG);
+}
+
+/* Clear the 'DMA Pointer Flip Flop'.
+ * Write 0 for LSB/MSB, 1 for MSB/LSB access.
+ * Use this once to initialize the FF to a known state.
+ * After that, keep track of it. :-)
+ * --- In order to do that, the DMA routines below should ---
+ * --- only be used while holding the DMA lock ! ---
+ */
+static __inline__ void clear_dma_ff(unsigned int dmanr)
+{
+	if (dmanr<=3)
+		dma_outb(0,  DMA1_CLEAR_FF_REG);
+	else
+		dma_outb(0,  DMA2_CLEAR_FF_REG);
+}
+
+/* set mode (above) for a specific DMA channel */
+static __inline__ void set_dma_mode(unsigned int dmanr, char mode)
+{
+	if (dmanr<=3)
+		dma_outb(mode | dmanr,	DMA1_MODE_REG);
+	else
+		dma_outb(mode | (dmanr&3),  DMA2_MODE_REG);
+}
+
+/* Set only the page register bits of the transfer address.
+ * This is used for successive transfers when we know the contents of
+ * the lower 16 bits of the DMA current address register, but a 64k boundary
+ * may have been crossed.
+ */
+static __inline__ void set_dma_page(unsigned int dmanr, char pagenr)
+{
+	switch(dmanr) {
+		case 0:
+			dma_outb(pagenr, DMA_PAGE_0);
+			break;
+		case 1:
+			dma_outb(pagenr, DMA_PAGE_1);
+			break;
+		case 2:
+			dma_outb(pagenr, DMA_PAGE_2);
+			break;
+		case 3:
+			dma_outb(pagenr, DMA_PAGE_3);
+			break;
+		case 5:
+			dma_outb(pagenr & 0xfe, DMA_PAGE_5);
+			break;
+		case 6:
+			dma_outb(pagenr & 0xfe, DMA_PAGE_6);
+			break;
+		case 7:
+			dma_outb(pagenr & 0xfe, DMA_PAGE_7);
+			break;
+	}
+}
+
+
+/* Set transfer address & page bits for specific DMA channel.
+ * Assumes dma flipflop is clear.
+ */
+static __inline__ void set_dma_addr(unsigned int dmanr, unsigned int a)
+{
+	set_dma_page(dmanr, a>>16);
+	if (dmanr <= 3)	 {
+	    dma_outb( a & 0xff, ((dmanr&3)<<1) + IO_DMA1_BASE );
+	    dma_outb( (a>>8) & 0xff, ((dmanr&3)<<1) + IO_DMA1_BASE );
+	}  else	 {
+	    dma_outb( (a>>1) & 0xff, ((dmanr&3)<<2) + IO_DMA2_BASE );
+	    dma_outb( (a>>9) & 0xff, ((dmanr&3)<<2) + IO_DMA2_BASE );
+	}
+}
+
+
+/* Set transfer size (max 64k for DMA0..3, 128k for DMA5..7) for
+ * a specific DMA channel.
+ * You must ensure the parameters are valid.
+ * NOTE: from a manual: "the number of transfers is one more
+ * than the initial word count"! This is taken into account.
+ * Assumes dma flip-flop is clear.
+ * NOTE 2: "count" represents _bytes_ and must be even for channels 5-7.
+ */
+static __inline__ void set_dma_count(unsigned int dmanr, unsigned int count)
+{
+	count--;
+	if (dmanr <= 3)	 {
+	    dma_outb( count & 0xff, ((dmanr&3)<<1) + 1 + IO_DMA1_BASE );
+	    dma_outb( (count>>8) & 0xff, ((dmanr&3)<<1) + 1 + IO_DMA1_BASE );
+	} else {
+	    dma_outb( (count>>1) & 0xff, ((dmanr&3)<<2) + 2 + IO_DMA2_BASE );
+	    dma_outb( (count>>9) & 0xff, ((dmanr&3)<<2) + 2 + IO_DMA2_BASE );
+	}
+}
+
+
+/* Get DMA residue count. After a DMA transfer, this
+ * should return zero. Reading this while a DMA transfer is
+ * still in progress will return unpredictable results.
+ * If called before the channel has been used, it may return 1.
+ * Otherwise, it returns the number of _bytes_ left to transfer.
+ *
+ * Assumes DMA flip-flop is clear.
+ */
+static __inline__ int get_dma_residue(unsigned int dmanr)
+{
+	unsigned int io_port = (dmanr<=3)? ((dmanr&3)<<1) + 1 + IO_DMA1_BASE
+					 : ((dmanr&3)<<2) + 2 + IO_DMA2_BASE;
+
+	/* using short to get 16-bit wrap around */
+	unsigned short count;
+
+	count = 1 + dma_inb(io_port);
+	count += dma_inb(io_port) << 8;
+
+	return (dmanr<=3)? count : (count<<1);
+}
+
+
+/* These are in kernel/dma.c: */
+extern int request_dma(unsigned int dmanr, const char * device_id);	/* reserve a DMA channel */
+extern void free_dma(unsigned int dmanr);	/* release it again */
+
+#endif /* _ASM_DMA_H */
diff --git a/arch/mips/include/asm/dmi.h b/arch/mips/include/asm/dmi.h
new file mode 100644
index 000000000..dc397f630
--- /dev/null
+++ b/arch/mips/include/asm/dmi.h
@@ -0,0 +1,20 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _ASM_DMI_H
+#define _ASM_DMI_H
+
+#include <linux/io.h>
+#include <linux/memblock.h>
+
+#define dmi_early_remap(x, l)		ioremap(x, l)
+#define dmi_early_unmap(x, l)		iounmap(x)
+#define dmi_remap(x, l)			ioremap_cache(x, l)
+#define dmi_unmap(x)			iounmap(x)
+
+/* MIPS initialize DMI scan before SLAB is ready, so we use memblock here */
+#define dmi_alloc(l)			memblock_alloc_low(l, PAGE_SIZE)
+
+#if defined(CONFIG_MACH_LOONGSON64)
+#define SMBIOS_ENTRY_POINT_SCAN_START	0xFFFE000
+#endif
+
+#endif /* _ASM_DMI_H */
diff --git a/arch/mips/include/asm/ds1287.h b/arch/mips/include/asm/ds1287.h
new file mode 100644
index 000000000..46cfb01f9
--- /dev/null
+++ b/arch/mips/include/asm/ds1287.h
@@ -0,0 +1,14 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ *  DS1287 timer functions.
+ *
+ *  Copyright (C) 2008  Yoichi Yuasa <yuasa@linux-mips.org>
+ */
+#ifndef __ASM_DS1287_H
+#define __ASM_DS1287_H
+
+extern int ds1287_timer_state(void);
+extern void ds1287_set_base_clock(unsigned int clock);
+extern int ds1287_clockevent_init(int irq);
+
+#endif
diff --git a/arch/mips/include/asm/dsemul.h b/arch/mips/include/asm/dsemul.h
new file mode 100644
index 000000000..08bfe8fa3
--- /dev/null
+++ b/arch/mips/include/asm/dsemul.h
@@ -0,0 +1,115 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2016 Imagination Technologies
+ * Author: Paul Burton <paul.burton@mips.com>
+ */
+
+#ifndef __MIPS_ASM_DSEMUL_H__
+#define __MIPS_ASM_DSEMUL_H__
+
+#include <asm/break.h>
+#include <asm/inst.h>
+
+/* Break instruction with special math emu break code set */
+#define BREAK_MATH(micromips)	(((micromips) ? 0x7 : 0xd) | (BRK_MEMU << 16))
+
+/* When used as a frame index, indicates the lack of a frame */
+#define BD_EMUFRAME_NONE	((int)BIT(31))
+
+struct mm_struct;
+struct pt_regs;
+struct task_struct;
+
+/**
+ * mips_dsemul() - 'Emulate' an instruction from a branch delay slot
+ * @regs:	User thread register context.
+ * @ir:		The instruction to be 'emulated'.
+ * @branch_pc:	The PC of the branch instruction.
+ * @cont_pc:	The PC to continue at following 'emulation'.
+ *
+ * Emulate or execute an arbitrary MIPS instruction within the context of
+ * the current user thread. This is used primarily to handle instructions
+ * in the delay slots of emulated branch instructions, for example FP
+ * branch instructions on systems without an FPU.
+ *
+ * Return: Zero on success, negative if ir is a NOP, signal number on failure.
+ */
+extern int mips_dsemul(struct pt_regs *regs, mips_instruction ir,
+		       unsigned long branch_pc, unsigned long cont_pc);
+
+/**
+ * do_dsemulret() - Return from a delay slot 'emulation' frame
+ * @xcp:	User thread register context.
+ *
+ * Call in response to the BRK_MEMU break instruction used to return to
+ * the kernel from branch delay slot 'emulation' frames following a call
+ * to mips_dsemul(). Restores the user thread PC to the value that was
+ * passed as the cpc parameter to mips_dsemul().
+ *
+ * Return: True if an emulation frame was returned from, else false.
+ */
+#ifdef CONFIG_MIPS_FP_SUPPORT
+extern bool do_dsemulret(struct pt_regs *xcp);
+#else
+static inline bool do_dsemulret(struct pt_regs *xcp)
+{
+	return false;
+}
+#endif
+
+/**
+ * dsemul_thread_cleanup() - Cleanup thread 'emulation' frame
+ * @tsk: The task structure associated with the thread
+ *
+ * If the thread @tsk has a branch delay slot 'emulation' frame
+ * allocated to it then free that frame.
+ *
+ * Return: True if a frame was freed, else false.
+ */
+#ifdef CONFIG_MIPS_FP_SUPPORT
+extern bool dsemul_thread_cleanup(struct task_struct *tsk);
+#else
+static inline bool dsemul_thread_cleanup(struct task_struct *tsk)
+{
+	return false;
+}
+#endif
+/**
+ * dsemul_thread_rollback() - Rollback from an 'emulation' frame
+ * @regs:	User thread register context.
+ *
+ * If the current thread, whose register context is represented by @regs,
+ * is executing within a delay slot 'emulation' frame then exit that
+ * frame. The PC will be rolled back to the branch if the instruction
+ * that was being 'emulated' has not yet executed, or advanced to the
+ * continuation PC if it has.
+ *
+ * Return: True if a frame was exited, else false.
+ */
+#ifdef CONFIG_MIPS_FP_SUPPORT
+extern bool dsemul_thread_rollback(struct pt_regs *regs);
+#else
+static inline bool dsemul_thread_rollback(struct pt_regs *regs)
+{
+	return false;
+}
+#endif
+
+/**
+ * dsemul_mm_cleanup() - Cleanup per-mm delay slot 'emulation' state
+ * @mm:		The struct mm_struct to cleanup state for.
+ *
+ * Cleanup state for the given @mm, ensuring that any memory allocated
+ * for delay slot 'emulation' book-keeping is freed. This is to be called
+ * before @mm is freed in order to avoid memory leaks.
+ */
+#ifdef CONFIG_MIPS_FP_SUPPORT
+extern void dsemul_mm_cleanup(struct mm_struct *mm);
+#else
+static inline void dsemul_mm_cleanup(struct mm_struct *mm)
+{
+	/* no-op */
+}
+#endif
+
+#endif /* __MIPS_ASM_DSEMUL_H__ */
diff --git a/arch/mips/include/asm/dsp.h b/arch/mips/include/asm/dsp.h
new file mode 100644
index 000000000..77fe0d675
--- /dev/null
+++ b/arch/mips/include/asm/dsp.h
@@ -0,0 +1,81 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2005 Mips Technologies
+ * Author: Chris Dearman, chris@mips.com derived from fpu.h
+ */
+#ifndef _ASM_DSP_H
+#define _ASM_DSP_H
+
+#include <asm/cpu.h>
+#include <asm/cpu-features.h>
+#include <asm/hazards.h>
+#include <asm/mipsregs.h>
+
+#define DSP_DEFAULT	0x00000000
+#define DSP_MASK	0x3f
+
+#define __enable_dsp_hazard()						\
+do {									\
+	asm("_ehb");							\
+} while (0)
+
+static inline void __init_dsp(void)
+{
+	mthi1(0);
+	mtlo1(0);
+	mthi2(0);
+	mtlo2(0);
+	mthi3(0);
+	mtlo3(0);
+	wrdsp(DSP_DEFAULT, DSP_MASK);
+}
+
+static inline void init_dsp(void)
+{
+	if (cpu_has_dsp)
+		__init_dsp();
+}
+
+#define __save_dsp(tsk)							\
+do {									\
+	tsk->thread.dsp.dspr[0] = mfhi1();				\
+	tsk->thread.dsp.dspr[1] = mflo1();				\
+	tsk->thread.dsp.dspr[2] = mfhi2();				\
+	tsk->thread.dsp.dspr[3] = mflo2();				\
+	tsk->thread.dsp.dspr[4] = mfhi3();				\
+	tsk->thread.dsp.dspr[5] = mflo3();				\
+	tsk->thread.dsp.dspcontrol = rddsp(DSP_MASK);			\
+} while (0)
+
+#define save_dsp(tsk)							\
+do {									\
+	if (cpu_has_dsp)						\
+		__save_dsp(tsk);					\
+} while (0)
+
+#define __restore_dsp(tsk)						\
+do {									\
+	mthi1(tsk->thread.dsp.dspr[0]);					\
+	mtlo1(tsk->thread.dsp.dspr[1]);					\
+	mthi2(tsk->thread.dsp.dspr[2]);					\
+	mtlo2(tsk->thread.dsp.dspr[3]);					\
+	mthi3(tsk->thread.dsp.dspr[4]);					\
+	mtlo3(tsk->thread.dsp.dspr[5]);					\
+	wrdsp(tsk->thread.dsp.dspcontrol, DSP_MASK);			\
+} while (0)
+
+#define restore_dsp(tsk)						\
+do {									\
+	if (cpu_has_dsp)						\
+		__restore_dsp(tsk);					\
+} while (0)
+
+#define __get_dsp_regs(tsk)						\
+({									\
+	if (tsk == current)						\
+		__save_dsp(current);					\
+									\
+	tsk->thread.dsp.dspr;						\
+})
+
+#endif /* _ASM_DSP_H */
diff --git a/arch/mips/include/asm/edac.h b/arch/mips/include/asm/edac.h
new file mode 100644
index 000000000..c5d147744
--- /dev/null
+++ b/arch/mips/include/asm/edac.h
@@ -0,0 +1,38 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef ASM_EDAC_H
+#define ASM_EDAC_H
+
+#include <asm/compiler.h>
+
+/* ECC atomic, DMA, SMP and interrupt safe scrub function */
+
+static inline void edac_atomic_scrub(void *va, u32 size)
+{
+	unsigned long *virt_addr = va;
+	unsigned long temp;
+	u32 i;
+
+	for (i = 0; i < size / sizeof(unsigned long); i++) {
+		/*
+		 * Very carefully read and write to memory atomically
+		 * so we are interrupt, DMA and SMP safe.
+		 *
+		 * Intel: asm("lock; addl $0, %0"::"m"(*virt_addr));
+		 */
+
+		__asm__ __volatile__ (
+		"	.set	push					\n"
+		"	.set	mips2					\n"
+		"1:	ll	%0, %1		# edac_atomic_scrub	\n"
+		"	addu	%0, $0					\n"
+		"	sc	%0, %1					\n"
+		"	beqz	%0, 1b					\n"
+		"	.set	pop					\n"
+		: "=&r" (temp), "=" GCC_OFF_SMALL_ASM() (*virt_addr)
+		: GCC_OFF_SMALL_ASM() (*virt_addr));
+
+		virt_addr++;
+	}
+}
+
+#endif
diff --git a/arch/mips/include/asm/elf.h b/arch/mips/include/asm/elf.h
new file mode 100644
index 000000000..dc8d28637
--- /dev/null
+++ b/arch/mips/include/asm/elf.h
@@ -0,0 +1,520 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Much of this is taken from binutils and GNU libc ...
+ */
+#ifndef _ASM_ELF_H
+#define _ASM_ELF_H
+
+#include <linux/auxvec.h>
+#include <linux/fs.h>
+#include <linux/mm_types.h>
+
+#include <uapi/linux/elf.h>
+
+#include <asm/current.h>
+
+/* ELF header e_flags defines. */
+/* MIPS architecture level. */
+#define EF_MIPS_ARCH_1		0x00000000	/* -mips1 code.	 */
+#define EF_MIPS_ARCH_2		0x10000000	/* -mips2 code.	 */
+#define EF_MIPS_ARCH_3		0x20000000	/* -mips3 code.	 */
+#define EF_MIPS_ARCH_4		0x30000000	/* -mips4 code.	 */
+#define EF_MIPS_ARCH_5		0x40000000	/* -mips5 code.	 */
+#define EF_MIPS_ARCH_32		0x50000000	/* MIPS32 code.	 */
+#define EF_MIPS_ARCH_64		0x60000000	/* MIPS64 code.	 */
+#define EF_MIPS_ARCH_32R2	0x70000000	/* MIPS32 R2 code.  */
+#define EF_MIPS_ARCH_64R2	0x80000000	/* MIPS64 R2 code.  */
+
+/* The ABI of a file. */
+#define EF_MIPS_ABI_O32		0x00001000	/* O32 ABI.  */
+#define EF_MIPS_ABI_O64		0x00002000	/* O32 extended for 64 bit.  */
+
+#define PT_MIPS_REGINFO		0x70000000
+#define PT_MIPS_RTPROC		0x70000001
+#define PT_MIPS_OPTIONS		0x70000002
+#define PT_MIPS_ABIFLAGS	0x70000003
+
+/* Flags in the e_flags field of the header */
+#define EF_MIPS_NOREORDER	0x00000001
+#define EF_MIPS_PIC		0x00000002
+#define EF_MIPS_CPIC		0x00000004
+#define EF_MIPS_ABI2		0x00000020
+#define EF_MIPS_OPTIONS_FIRST	0x00000080
+#define EF_MIPS_32BITMODE	0x00000100
+#define EF_MIPS_FP64		0x00000200
+#define EF_MIPS_NAN2008		0x00000400
+#define EF_MIPS_ABI		0x0000f000
+#define EF_MIPS_ARCH		0xf0000000
+
+#define DT_MIPS_RLD_VERSION	0x70000001
+#define DT_MIPS_TIME_STAMP	0x70000002
+#define DT_MIPS_ICHECKSUM	0x70000003
+#define DT_MIPS_IVERSION	0x70000004
+#define DT_MIPS_FLAGS		0x70000005
+	#define RHF_NONE	0x00000000
+	#define RHF_HARDWAY	0x00000001
+	#define RHF_NOTPOT	0x00000002
+	#define RHF_SGI_ONLY	0x00000010
+#define DT_MIPS_BASE_ADDRESS	0x70000006
+#define DT_MIPS_CONFLICT	0x70000008
+#define DT_MIPS_LIBLIST		0x70000009
+#define DT_MIPS_LOCAL_GOTNO	0x7000000a
+#define DT_MIPS_CONFLICTNO	0x7000000b
+#define DT_MIPS_LIBLISTNO	0x70000010
+#define DT_MIPS_SYMTABNO	0x70000011
+#define DT_MIPS_UNREFEXTNO	0x70000012
+#define DT_MIPS_GOTSYM		0x70000013
+#define DT_MIPS_HIPAGENO	0x70000014
+#define DT_MIPS_RLD_MAP		0x70000016
+
+#define R_MIPS_NONE		0
+#define R_MIPS_16		1
+#define R_MIPS_32		2
+#define R_MIPS_REL32		3
+#define R_MIPS_26		4
+#define R_MIPS_HI16		5
+#define R_MIPS_LO16		6
+#define R_MIPS_GPREL16		7
+#define R_MIPS_LITERAL		8
+#define R_MIPS_GOT16		9
+#define R_MIPS_PC16		10
+#define R_MIPS_CALL16		11
+#define R_MIPS_GPREL32		12
+/* The remaining relocs are defined on Irix, although they are not
+   in the MIPS ELF ABI.	 */
+#define R_MIPS_UNUSED1		13
+#define R_MIPS_UNUSED2		14
+#define R_MIPS_UNUSED3		15
+#define R_MIPS_SHIFT5		16
+#define R_MIPS_SHIFT6		17
+#define R_MIPS_64		18
+#define R_MIPS_GOT_DISP		19
+#define R_MIPS_GOT_PAGE		20
+#define R_MIPS_GOT_OFST		21
+/*
+ * The following two relocation types are specified in the MIPS ABI
+ * conformance guide version 1.2 but not yet in the psABI.
+ */
+#define R_MIPS_GOTHI16		22
+#define R_MIPS_GOTLO16		23
+#define R_MIPS_SUB		24
+#define R_MIPS_INSERT_A		25
+#define R_MIPS_INSERT_B		26
+#define R_MIPS_DELETE		27
+#define R_MIPS_HIGHER		28
+#define R_MIPS_HIGHEST		29
+/*
+ * The following two relocation types are specified in the MIPS ABI
+ * conformance guide version 1.2 but not yet in the psABI.
+ */
+#define R_MIPS_CALLHI16		30
+#define R_MIPS_CALLLO16		31
+/*
+ * Introduced for MIPSr6.
+ */
+#define R_MIPS_PC21_S2		60
+#define R_MIPS_PC26_S2		61
+/*
+ * This range is reserved for vendor specific relocations.
+ */
+#define R_MIPS_LOVENDOR		100
+#define R_MIPS_HIVENDOR		127
+
+#define SHN_MIPS_ACCOMON	0xff00		/* Allocated common symbols */
+#define SHN_MIPS_TEXT		0xff01		/* Allocated test symbols.  */
+#define SHN_MIPS_DATA		0xff02		/* Allocated data symbols.  */
+#define SHN_MIPS_SCOMMON	0xff03		/* Small common symbols */
+#define SHN_MIPS_SUNDEFINED	0xff04		/* Small undefined symbols */
+
+#define SHT_MIPS_LIST		0x70000000
+#define SHT_MIPS_CONFLICT	0x70000002
+#define SHT_MIPS_GPTAB		0x70000003
+#define SHT_MIPS_UCODE		0x70000004
+#define SHT_MIPS_DEBUG		0x70000005
+#define SHT_MIPS_REGINFO	0x70000006
+#define SHT_MIPS_PACKAGE	0x70000007
+#define SHT_MIPS_PACKSYM	0x70000008
+#define SHT_MIPS_RELD		0x70000009
+#define SHT_MIPS_IFACE		0x7000000b
+#define SHT_MIPS_CONTENT	0x7000000c
+#define SHT_MIPS_OPTIONS	0x7000000d
+#define SHT_MIPS_SHDR		0x70000010
+#define SHT_MIPS_FDESC		0x70000011
+#define SHT_MIPS_EXTSYM		0x70000012
+#define SHT_MIPS_DENSE		0x70000013
+#define SHT_MIPS_PDESC		0x70000014
+#define SHT_MIPS_LOCSYM		0x70000015
+#define SHT_MIPS_AUXSYM		0x70000016
+#define SHT_MIPS_OPTSYM		0x70000017
+#define SHT_MIPS_LOCSTR		0x70000018
+#define SHT_MIPS_LINE		0x70000019
+#define SHT_MIPS_RFDESC		0x7000001a
+#define SHT_MIPS_DELTASYM	0x7000001b
+#define SHT_MIPS_DELTAINST	0x7000001c
+#define SHT_MIPS_DELTACLASS	0x7000001d
+#define SHT_MIPS_DWARF		0x7000001e
+#define SHT_MIPS_DELTADECL	0x7000001f
+#define SHT_MIPS_SYMBOL_LIB	0x70000020
+#define SHT_MIPS_EVENTS		0x70000021
+#define SHT_MIPS_TRANSLATE	0x70000022
+#define SHT_MIPS_PIXIE		0x70000023
+#define SHT_MIPS_XLATE		0x70000024
+#define SHT_MIPS_XLATE_DEBUG	0x70000025
+#define SHT_MIPS_WHIRL		0x70000026
+#define SHT_MIPS_EH_REGION	0x70000027
+#define SHT_MIPS_XLATE_OLD	0x70000028
+#define SHT_MIPS_PDR_EXCEPTION	0x70000029
+
+#define SHF_MIPS_GPREL		0x10000000
+#define SHF_MIPS_MERGE		0x20000000
+#define SHF_MIPS_ADDR		0x40000000
+#define SHF_MIPS_STRING		0x80000000
+#define SHF_MIPS_NOSTRIP	0x08000000
+#define SHF_MIPS_LOCAL		0x04000000
+#define SHF_MIPS_NAMES		0x02000000
+#define SHF_MIPS_NODUPES	0x01000000
+
+#define MIPS_ABI_FP_ANY		0	/* FP ABI doesn't matter */
+#define MIPS_ABI_FP_DOUBLE	1	/* -mdouble-float */
+#define MIPS_ABI_FP_SINGLE	2	/* -msingle-float */
+#define MIPS_ABI_FP_SOFT	3	/* -msoft-float */
+#define MIPS_ABI_FP_OLD_64	4	/* -mips32r2 -mfp64 */
+#define MIPS_ABI_FP_XX		5	/* -mfpxx */
+#define MIPS_ABI_FP_64		6	/* -mips32r2 -mfp64 */
+#define MIPS_ABI_FP_64A		7	/* -mips32r2 -mfp64 -mno-odd-spreg */
+
+struct mips_elf_abiflags_v0 {
+	uint16_t version;	/* Version of flags structure */
+	uint8_t isa_level;	/* The level of the ISA: 1-5, 32, 64 */
+	uint8_t isa_rev;	/* The revision of ISA: 0 for MIPS V and below,
+				   1-n otherwise */
+	uint8_t gpr_size;	/* The size of general purpose registers */
+	uint8_t cpr1_size;	/* The size of co-processor 1 registers */
+	uint8_t cpr2_size;	/* The size of co-processor 2 registers */
+	uint8_t fp_abi;		/* The floating-point ABI */
+	uint32_t isa_ext;	/* Mask of processor-specific extensions */
+	uint32_t ases;		/* Mask of ASEs used */
+	uint32_t flags1;	/* Mask of general flags */
+	uint32_t flags2;
+};
+
+/* ELF register definitions */
+#define ELF_NGREG	45
+#define ELF_NFPREG	33
+
+typedef unsigned long elf_greg_t;
+typedef elf_greg_t elf_gregset_t[ELF_NGREG];
+
+typedef double elf_fpreg_t;
+typedef elf_fpreg_t elf_fpregset_t[ELF_NFPREG];
+
+void mips_dump_regs32(u32 *uregs, const struct pt_regs *regs);
+void mips_dump_regs64(u64 *uregs, const struct pt_regs *regs);
+
+#ifdef CONFIG_32BIT
+/*
+ * This is used to ensure we don't load something for the wrong architecture.
+ */
+#define elf_check_arch elf32_check_arch
+
+/*
+ * These are used to set parameters in the core dumps.
+ */
+#define ELF_CLASS	ELFCLASS32
+
+#define ELF_CORE_COPY_REGS(dest, regs) \
+	mips_dump_regs32((u32 *)&(dest), (regs));
+
+#endif /* CONFIG_32BIT */
+
+#ifdef CONFIG_64BIT
+/*
+ * This is used to ensure we don't load something for the wrong architecture.
+ */
+#define elf_check_arch elf64_check_arch
+#define compat_elf_check_arch elf32_check_arch
+
+/*
+ * These are used to set parameters in the core dumps.
+ */
+#define ELF_CLASS	ELFCLASS64
+
+#define ELF_CORE_COPY_REGS(dest, regs) \
+	mips_dump_regs64((u64 *)&(dest), (regs));
+
+#endif /* CONFIG_64BIT */
+
+/*
+ * These are used to set parameters in the core dumps.
+ */
+#ifdef __MIPSEB__
+#define ELF_DATA	ELFDATA2MSB
+#elif defined(__MIPSEL__)
+#define ELF_DATA	ELFDATA2LSB
+#endif
+#define ELF_ARCH	EM_MIPS
+
+/*
+ * In order to be sure that we don't attempt to execute an O32 binary which
+ * requires 64 bit FP (FR=1) on a system which does not support it we refuse
+ * to execute any binary which has bits specified by the following macro set
+ * in its ELF header flags.
+ */
+#ifdef CONFIG_MIPS_O32_FP64_SUPPORT
+# define __MIPS_O32_FP64_MUST_BE_ZERO	0
+#else
+# define __MIPS_O32_FP64_MUST_BE_ZERO	EF_MIPS_FP64
+#endif
+
+#define mips_elf_check_machine(x) ((x)->e_machine == EM_MIPS)
+
+#define vmcore_elf32_check_arch mips_elf_check_machine
+#define vmcore_elf64_check_arch mips_elf_check_machine
+
+/*
+ * Return non-zero if HDR identifies an o32 or n32 ELF binary.
+ */
+#define elf32_check_arch(hdr)						\
+({									\
+	int __res = 1;							\
+	struct elfhdr *__h = (hdr);					\
+									\
+	if (!mips_elf_check_machine(__h))				\
+		__res = 0;						\
+	if (__h->e_ident[EI_CLASS] != ELFCLASS32)			\
+		__res = 0;						\
+	if ((__h->e_flags & EF_MIPS_ABI2) != 0) {			\
+		if (!IS_ENABLED(CONFIG_MIPS32_N32) ||			\
+		     (__h->e_flags & EF_MIPS_ABI))			\
+			__res = 0;					\
+	} else {							\
+		if (IS_ENABLED(CONFIG_64BIT) && !IS_ENABLED(CONFIG_MIPS32_O32)) \
+			__res = 0;					\
+		if (((__h->e_flags & EF_MIPS_ABI) != 0) &&		\
+		    ((__h->e_flags & EF_MIPS_ABI) != EF_MIPS_ABI_O32))	\
+			__res = 0;					\
+		if (__h->e_flags & __MIPS_O32_FP64_MUST_BE_ZERO)	\
+			__res = 0;					\
+	}								\
+	__res;								\
+})
+
+/*
+ * Return non-zero if HDR identifies an n64 ELF binary.
+ */
+#define elf64_check_arch(hdr)						\
+({									\
+	int __res = 1;							\
+	struct elfhdr *__h = (hdr);					\
+									\
+	if (!mips_elf_check_machine(__h))				\
+		__res = 0;						\
+	if (__h->e_ident[EI_CLASS] != ELFCLASS64)			\
+		__res = 0;						\
+									\
+	__res;								\
+})
+
+struct mips_abi;
+
+extern struct mips_abi mips_abi;
+extern struct mips_abi mips_abi_32;
+extern struct mips_abi mips_abi_n32;
+
+#ifdef CONFIG_32BIT
+
+#define SET_PERSONALITY2(ex, state)					\
+do {									\
+	clear_thread_flag(TIF_HYBRID_FPREGS);				\
+	set_thread_flag(TIF_32BIT_FPREGS);				\
+									\
+	current->thread.abi = &mips_abi;				\
+									\
+	mips_set_personality_fp(state);					\
+	mips_set_personality_nan(state);				\
+									\
+	if (personality(current->personality) != PER_LINUX)		\
+		set_personality(PER_LINUX);				\
+} while (0)
+
+#endif /* CONFIG_32BIT */
+
+#ifdef CONFIG_64BIT
+
+#ifdef CONFIG_MIPS32_N32
+#define __SET_PERSONALITY32_N32()					\
+	do {								\
+		set_thread_flag(TIF_32BIT_ADDR);			\
+									\
+		current->thread.abi = &mips_abi_n32;			\
+	} while (0)
+#else
+#define __SET_PERSONALITY32_N32()					\
+	do { } while (0)
+#endif
+
+#ifdef CONFIG_MIPS32_O32
+#define __SET_PERSONALITY32_O32(ex, state)				\
+	do {								\
+		set_thread_flag(TIF_32BIT_REGS);			\
+		set_thread_flag(TIF_32BIT_ADDR);			\
+		clear_thread_flag(TIF_HYBRID_FPREGS);			\
+		set_thread_flag(TIF_32BIT_FPREGS);			\
+									\
+		current->thread.abi = &mips_abi_32;			\
+									\
+		mips_set_personality_fp(state);				\
+	} while (0)
+#else
+#define __SET_PERSONALITY32_O32(ex, state)				\
+	do { } while (0)
+#endif
+
+#ifdef CONFIG_MIPS32_COMPAT
+#define __SET_PERSONALITY32(ex, state)					\
+do {									\
+	if ((((ex).e_flags & EF_MIPS_ABI2) != 0) &&			\
+	     ((ex).e_flags & EF_MIPS_ABI) == 0)				\
+		__SET_PERSONALITY32_N32();				\
+	else								\
+		__SET_PERSONALITY32_O32(ex, state);			\
+} while (0)
+#else
+#define __SET_PERSONALITY32(ex, state) do { } while (0)
+#endif
+
+#define SET_PERSONALITY2(ex, state)					\
+do {									\
+	unsigned int p;							\
+									\
+	clear_thread_flag(TIF_32BIT_REGS);				\
+	clear_thread_flag(TIF_32BIT_FPREGS);				\
+	clear_thread_flag(TIF_HYBRID_FPREGS);				\
+	clear_thread_flag(TIF_32BIT_ADDR);				\
+	current->personality &= ~READ_IMPLIES_EXEC;			\
+									\
+	if ((ex).e_ident[EI_CLASS] == ELFCLASS32)			\
+		__SET_PERSONALITY32(ex, state);				\
+	else								\
+		current->thread.abi = &mips_abi;			\
+									\
+	mips_set_personality_nan(state);				\
+									\
+	p = personality(current->personality);				\
+	if (p != PER_LINUX32 && p != PER_LINUX)				\
+		set_personality(PER_LINUX);				\
+} while (0)
+
+#endif /* CONFIG_64BIT */
+
+#define CORE_DUMP_USE_REGSET
+#define ELF_EXEC_PAGESIZE	PAGE_SIZE
+
+/* This yields a mask that user programs can use to figure out what
+   instruction set this cpu supports.  This could be done in userspace,
+   but it's not easy, and we've already done it here.  */
+
+#define ELF_HWCAP	(elf_hwcap)
+extern unsigned int elf_hwcap;
+#include <asm/hwcap.h>
+
+/*
+ * This yields a string that ld.so will use to load implementation
+ * specific libraries for optimization.	 This is more specific in
+ * intent than poking at uname or /proc/cpuinfo.
+ */
+
+#define ELF_PLATFORM  __elf_platform
+extern const char *__elf_platform;
+
+#define ELF_BASE_PLATFORM  __elf_base_platform
+extern const char *__elf_base_platform;
+
+/*
+ * See comments in asm-alpha/elf.h, this is the same thing
+ * on the MIPS.
+ */
+#define ELF_PLAT_INIT(_r, load_addr)	do { \
+	_r->regs[1] = _r->regs[2] = _r->regs[3] = _r->regs[4] = 0;	\
+	_r->regs[5] = _r->regs[6] = _r->regs[7] = _r->regs[8] = 0;	\
+	_r->regs[9] = _r->regs[10] = _r->regs[11] = _r->regs[12] = 0;	\
+	_r->regs[13] = _r->regs[14] = _r->regs[15] = _r->regs[16] = 0;	\
+	_r->regs[17] = _r->regs[18] = _r->regs[19] = _r->regs[20] = 0;	\
+	_r->regs[21] = _r->regs[22] = _r->regs[23] = _r->regs[24] = 0;	\
+	_r->regs[25] = _r->regs[26] = _r->regs[27] = _r->regs[28] = 0;	\
+	_r->regs[30] = _r->regs[31] = 0;				\
+} while (0)
+
+/* This is the location that an ET_DYN program is loaded if exec'ed.  Typical
+   use of this is to invoke "./ld.so someprog" to test out a new version of
+   the loader.	We need to make sure that it is out of the way of the program
+   that it will "exec", and that there is sufficient room for the brk.	*/
+
+#define ELF_ET_DYN_BASE		(TASK_SIZE / 3 * 2)
+
+/* update AT_VECTOR_SIZE_ARCH if the number of NEW_AUX_ENT entries changes */
+#define ARCH_DLINFO							\
+do {									\
+	NEW_AUX_ENT(AT_SYSINFO_EHDR,					\
+		    (unsigned long)current->mm->context.vdso);		\
+} while (0)
+
+#define ARCH_HAS_SETUP_ADDITIONAL_PAGES 1
+struct linux_binprm;
+extern int arch_setup_additional_pages(struct linux_binprm *bprm,
+				       int uses_interp);
+
+#ifdef CONFIG_MIPS_FP_SUPPORT
+
+struct arch_elf_state {
+	int nan_2008;
+	int fp_abi;
+	int interp_fp_abi;
+	int overall_fp_mode;
+};
+
+#define MIPS_ABI_FP_UNKNOWN	(-1)	/* Unknown FP ABI (kernel internal) */
+
+#define INIT_ARCH_ELF_STATE {			\
+	.nan_2008 = -1,				\
+	.fp_abi = MIPS_ABI_FP_UNKNOWN,		\
+	.interp_fp_abi = MIPS_ABI_FP_UNKNOWN,	\
+	.overall_fp_mode = -1,			\
+}
+
+extern int arch_elf_pt_proc(void *ehdr, void *phdr, struct file *elf,
+			    bool is_interp, struct arch_elf_state *state);
+
+extern int arch_check_elf(void *ehdr, bool has_interpreter, void *interp_ehdr,
+			  struct arch_elf_state *state);
+
+/* Whether to accept legacy-NaN and 2008-NaN user binaries.  */
+extern bool mips_use_nan_legacy;
+extern bool mips_use_nan_2008;
+
+extern void mips_set_personality_nan(struct arch_elf_state *state);
+extern void mips_set_personality_fp(struct arch_elf_state *state);
+
+#else /* !CONFIG_MIPS_FP_SUPPORT */
+
+struct arch_elf_state;
+
+static inline void mips_set_personality_nan(struct arch_elf_state *state)
+{
+	/* no-op */
+}
+
+static inline void mips_set_personality_fp(struct arch_elf_state *state)
+{
+	/* no-op */
+}
+
+#endif /* !CONFIG_MIPS_FP_SUPPORT */
+
+#define elf_read_implies_exec(ex, stk) mips_elf_read_implies_exec(&(ex), stk)
+extern int mips_elf_read_implies_exec(void *elf_ex, int exstack);
+
+#endif /* _ASM_ELF_H */
diff --git a/arch/mips/include/asm/elfcore-compat.h b/arch/mips/include/asm/elfcore-compat.h
new file mode 100644
index 000000000..2f0f0103c
--- /dev/null
+++ b/arch/mips/include/asm/elfcore-compat.h
@@ -0,0 +1,29 @@
+#ifndef _ASM_MIPS_ELFCORE_COMPAT_H
+#define _ASM_MIPS_ELFCORE_COMPAT_H
+
+/*
+ * On mips we have two 32bit ABIs - o32 and n32.  The latter
+ * has bigger registers, so we use it for compat_elf_regset_t.
+ * The former uses o32_elf_prstatus and PRSTATUS_SIZE/SET_PR_FPVALID
+ * are used to choose the size and location of ->pr_fpvalid of
+ * the layout actually used.
+ */
+typedef elf_gregset_t compat_elf_gregset_t;
+
+struct o32_elf_prstatus
+{
+	struct compat_elf_prstatus_common	common;
+	unsigned int 			pr_reg[ELF_NGREG];
+	compat_int_t			pr_fpvalid;
+};
+
+#define PRSTATUS_SIZE \
+	(!test_thread_flag(TIF_32BIT_REGS) \
+		? sizeof(struct compat_elf_prstatus) \
+		: sizeof(struct o32_elf_prstatus))
+#define SET_PR_FPVALID(S) \
+	(*(!test_thread_flag(TIF_32BIT_REGS) \
+		? &(S)->pr_fpvalid 	\
+		: &((struct o32_elf_prstatus *)(S))->pr_fpvalid) = 1)
+
+#endif
diff --git a/arch/mips/include/asm/errno.h b/arch/mips/include/asm/errno.h
new file mode 100644
index 000000000..21d91cdfe
--- /dev/null
+++ b/arch/mips/include/asm/errno.h
@@ -0,0 +1,17 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995, 1999, 2001, 2002 by Ralf Baechle
+ */
+#ifndef _ASM_ERRNO_H
+#define _ASM_ERRNO_H
+
+#include <uapi/asm/errno.h>
+
+
+/* The biggest error number defined here or in <linux/errno.h>. */
+#define EMAXERRNO	1133
+
+#endif /* _ASM_ERRNO_H */
diff --git a/arch/mips/include/asm/eva.h b/arch/mips/include/asm/eva.h
new file mode 100644
index 000000000..a3d1807f2
--- /dev/null
+++ b/arch/mips/include/asm/eva.h
@@ -0,0 +1,43 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2014, Imagination Technologies Ltd.
+ *
+ * EVA functions for generic code
+ */
+
+#ifndef _ASM_EVA_H
+#define _ASM_EVA_H
+
+#include <kernel-entry-init.h>
+
+#ifdef __ASSEMBLY__
+
+#ifdef CONFIG_EVA
+
+/*
+ * EVA early init code
+ *
+ * Platforms must define their own 'platform_eva_init' macro in
+ * their kernel-entry-init.h header. This macro usually does the
+ * platform specific configuration of the segmentation registers,
+ * and it is normally called from assembly code.
+ *
+ */
+
+.macro eva_init
+platform_eva_init
+.endm
+
+#else
+
+.macro eva_init
+.endm
+
+#endif /* CONFIG_EVA */
+
+#endif /* __ASSEMBLY__ */
+
+#endif
diff --git a/arch/mips/include/asm/exec.h b/arch/mips/include/asm/exec.h
new file mode 100644
index 000000000..c1f6afa4b
--- /dev/null
+++ b/arch/mips/include/asm/exec.h
@@ -0,0 +1,17 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994, 95, 96, 97, 98, 99, 2003, 06 by Ralf Baechle
+ * Copyright (C) 1996 by Paul M. Antoine
+ * Copyright (C) 1999 Silicon Graphics
+ * Kevin D. Kissell, kevink@mips.org and Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 2000 MIPS Technologies, Inc.
+ */
+#ifndef _ASM_EXEC_H
+#define _ASM_EXEC_H
+
+extern unsigned long arch_align_stack(unsigned long sp);
+
+#endif /* _ASM_EXEC_H */
diff --git a/arch/mips/include/asm/extable.h b/arch/mips/include/asm/extable.h
new file mode 100644
index 000000000..78d0ae156
--- /dev/null
+++ b/arch/mips/include/asm/extable.h
@@ -0,0 +1,14 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _ASM_EXTABLE_H
+#define _ASM_EXTABLE_H
+
+struct exception_table_entry
+{
+	unsigned long insn;
+	unsigned long nextinsn;
+};
+
+struct pt_regs;
+extern int fixup_exception(struct pt_regs *regs);
+
+#endif
diff --git a/arch/mips/include/asm/fb.h b/arch/mips/include/asm/fb.h
new file mode 100644
index 000000000..bd3f68c9d
--- /dev/null
+++ b/arch/mips/include/asm/fb.h
@@ -0,0 +1,19 @@
+#ifndef _ASM_FB_H_
+#define _ASM_FB_H_
+
+#include <linux/fb.h>
+#include <linux/fs.h>
+#include <asm/page.h>
+
+static inline void fb_pgprotect(struct file *file, struct vm_area_struct *vma,
+				unsigned long off)
+{
+	vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot);
+}
+
+static inline int fb_is_primary_device(struct fb_info *info)
+{
+	return 0;
+}
+
+#endif /* _ASM_FB_H_ */
diff --git a/arch/mips/include/asm/fixmap.h b/arch/mips/include/asm/fixmap.h
new file mode 100644
index 000000000..beea14761
--- /dev/null
+++ b/arch/mips/include/asm/fixmap.h
@@ -0,0 +1,79 @@
+/*
+ * fixmap.h: compile-time virtual memory allocation
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1998 Ingo Molnar
+ *
+ * Support of BIGMEM added by Gerhard Wichert, Siemens AG, July 1999
+ */
+
+#ifndef _ASM_FIXMAP_H
+#define _ASM_FIXMAP_H
+
+#include <asm/page.h>
+#include <spaces.h>
+#ifdef CONFIG_HIGHMEM
+#include <linux/threads.h>
+#include <asm/kmap_size.h>
+#endif
+
+/*
+ * Here we define all the compile-time 'special' virtual
+ * addresses. The point is to have a constant address at
+ * compile time, but to set the physical address only
+ * in the boot process. We allocate these special  addresses
+ * from the end of virtual memory (0xfffff000) backwards.
+ * Also this lets us do fail-safe vmalloc(), we
+ * can guarantee that these special addresses and
+ * vmalloc()-ed addresses never overlap.
+ *
+ * these 'compile-time allocated' memory buffers are
+ * fixed-size 4k pages. (or larger if used with an increment
+ * highger than 1) use fixmap_set(idx,phys) to associate
+ * physical memory with fixmap indices.
+ *
+ * TLB entries of such buffers will not be flushed across
+ * task switches.
+ */
+
+/*
+ * on UP currently we will have no trace of the fixmap mechanizm,
+ * no page table allocations, etc. This might change in the
+ * future, say framebuffers for the console driver(s) could be
+ * fix-mapped?
+ */
+enum fixed_addresses {
+#define FIX_N_COLOURS 8
+	FIX_CMAP_BEGIN,
+	FIX_CMAP_END = FIX_CMAP_BEGIN + (FIX_N_COLOURS * 2),
+#ifdef CONFIG_HIGHMEM
+	/* reserved pte's for temporary kernel mappings */
+	FIX_KMAP_BEGIN = FIX_CMAP_END + 1,
+	FIX_KMAP_END = FIX_KMAP_BEGIN + (KM_MAX_IDX * NR_CPUS) - 1,
+#endif
+	__end_of_fixed_addresses
+};
+
+/*
+ * used by vmalloc.c.
+ *
+ * Leave one empty page between vmalloc'ed areas and
+ * the start of the fixmap, and leave one page empty
+ * at the top of mem..
+ */
+#define FIXADDR_SIZE	(__end_of_fixed_addresses << PAGE_SHIFT)
+#define FIXADDR_START	(FIXADDR_TOP - FIXADDR_SIZE)
+
+#include <asm-generic/fixmap.h>
+
+/*
+ * Called from pgtable_init()
+ */
+extern void fixrange_init(unsigned long start, unsigned long end,
+	pgd_t *pgd_base);
+
+
+#endif
diff --git a/arch/mips/include/asm/floppy.h b/arch/mips/include/asm/floppy.h
new file mode 100644
index 000000000..021d09ae5
--- /dev/null
+++ b/arch/mips/include/asm/floppy.h
@@ -0,0 +1,56 @@
+/*
+ * Architecture specific parts of the Floppy driver
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995 - 2000 Ralf Baechle
+ */
+#ifndef _ASM_FLOPPY_H
+#define _ASM_FLOPPY_H
+
+#include <asm/io.h>
+
+static inline void fd_cacheflush(char * addr, long size)
+{
+	dma_cache_wback_inv((unsigned long)addr, size);
+}
+
+#define MAX_BUFFER_SECTORS 24
+
+
+/*
+ * And on Mips's the CMOS info fails also ...
+ *
+ * FIXME: This information should come from the ARC configuration tree
+ *	  or wherever a particular machine has stored this ...
+ */
+#define FLOPPY0_TYPE		fd_drive_type(0)
+#define FLOPPY1_TYPE		fd_drive_type(1)
+
+#define FDC1			fd_getfdaddr1()
+
+#define N_FDC 1			/* do you *really* want a second controller? */
+#define N_DRIVE 8
+
+/*
+ * The DMA channel used by the floppy controller cannot access data at
+ * addresses >= 16MB
+ *
+ * Went back to the 1MB limit, as some people had problems with the floppy
+ * driver otherwise. It doesn't matter much for performance anyway, as most
+ * floppy accesses go through the track buffer.
+ *
+ * On MIPSes using vdma, this actually means that *all* transfers go thru
+ * the * track buffer since 0x1000000 is always smaller than KSEG0/1.
+ * Actually this needs to be a bit more complicated since the so much different
+ * hardware available with MIPS CPUs ...
+ */
+#define CROSS_64KB(a, s) ((unsigned long)(a)/K_64 != ((unsigned long)(a) + (s) - 1) / K_64)
+
+#define EXTRA_FLOPPY_PARAMS
+
+#include <floppy.h>
+
+#endif /* _ASM_FLOPPY_H */
diff --git a/arch/mips/include/asm/fpregdef.h b/arch/mips/include/asm/fpregdef.h
new file mode 100644
index 000000000..f184ba088
--- /dev/null
+++ b/arch/mips/include/asm/fpregdef.h
@@ -0,0 +1,113 @@
+/*
+ * Definitions for the FPU register names
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995, 1999 Ralf Baechle
+ * Copyright (C) 1985 MIPS Computer Systems, Inc.
+ * Copyright (C) 1990 - 1992, 1999 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_FPREGDEF_H
+#define _ASM_FPREGDEF_H
+
+#include <asm/sgidefs.h>
+
+/*
+ * starting with binutils 2.24.51.20140729, MIPS binutils warn about mixing
+ * hardfloat and softfloat object files.  The kernel build uses soft-float by
+ * default, so we also need to pass -msoft-float along to GAS if it supports it.
+ * But this in turn causes assembler errors in files which access hardfloat
+ * registers.  We detect if GAS supports "-msoft-float" in the Makefile and
+ * explicitly put ".set hardfloat" where floating point registers are touched.
+ */
+#ifdef GAS_HAS_SET_HARDFLOAT
+#define SET_HARDFLOAT .set hardfloat
+#else
+#define SET_HARDFLOAT
+#endif
+
+#if _MIPS_SIM == _MIPS_SIM_ABI32
+
+/*
+ * These definitions only cover the R3000-ish 16/32 register model.
+ * But we're trying to be R3000 friendly anyway ...
+ */
+#define fv0	$f0	 /* return value */
+#define fv0f	$f1
+#define fv1	$f2
+#define fv1f	$f3
+#define fa0	$f12	 /* argument registers */
+#define fa0f	$f13
+#define fa1	$f14
+#define fa1f	$f15
+#define ft0	$f4	 /* caller saved */
+#define ft0f	$f5
+#define ft1	$f6
+#define ft1f	$f7
+#define ft2	$f8
+#define ft2f	$f9
+#define ft3	$f10
+#define ft3f	$f11
+#define ft4	$f16
+#define ft4f	$f17
+#define ft5	$f18
+#define ft5f	$f19
+#define fs0	$f20	 /* callee saved */
+#define fs0f	$f21
+#define fs1	$f22
+#define fs1f	$f23
+#define fs2	$f24
+#define fs2f	$f25
+#define fs3	$f26
+#define fs3f	$f27
+#define fs4	$f28
+#define fs4f	$f29
+#define fs5	$f30
+#define fs5f	$f31
+
+#define fcr31	$31	 /* FPU status register */
+
+#endif /* _MIPS_SIM == _MIPS_SIM_ABI32 */
+
+#if _MIPS_SIM == _MIPS_SIM_ABI64 || _MIPS_SIM == _MIPS_SIM_NABI32
+
+#define fv0	$f0	/* return value */
+#define fv1	$f2
+#define fa0	$f12	/* argument registers */
+#define fa1	$f13
+#define fa2	$f14
+#define fa3	$f15
+#define fa4	$f16
+#define fa5	$f17
+#define fa6	$f18
+#define fa7	$f19
+#define ft0	$f4	/* caller saved */
+#define ft1	$f5
+#define ft2	$f6
+#define ft3	$f7
+#define ft4	$f8
+#define ft5	$f9
+#define ft6	$f10
+#define ft7	$f11
+#define ft8	$f20
+#define ft9	$f21
+#define ft10	$f22
+#define ft11	$f23
+#define ft12	$f1
+#define ft13	$f3
+#define fs0	$f24	/* callee saved */
+#define fs1	$f25
+#define fs2	$f26
+#define fs3	$f27
+#define fs4	$f28
+#define fs5	$f29
+#define fs6	$f30
+#define fs7	$f31
+
+#define fcr31	$31
+
+#endif /* _MIPS_SIM == _MIPS_SIM_ABI64 || _MIPS_SIM == _MIPS_SIM_NABI32 */
+
+#endif /* _ASM_FPREGDEF_H */
diff --git a/arch/mips/include/asm/fpu.h b/arch/mips/include/asm/fpu.h
new file mode 100644
index 000000000..86310d6e1
--- /dev/null
+++ b/arch/mips/include/asm/fpu.h
@@ -0,0 +1,328 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2002 MontaVista Software Inc.
+ * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net
+ */
+#ifndef _ASM_FPU_H
+#define _ASM_FPU_H
+
+#include <linux/sched.h>
+#include <linux/sched/task_stack.h>
+#include <linux/ptrace.h>
+#include <linux/thread_info.h>
+#include <linux/bitops.h>
+
+#include <asm/mipsregs.h>
+#include <asm/cpu.h>
+#include <asm/cpu-features.h>
+#include <asm/fpu_emulator.h>
+#include <asm/hazards.h>
+#include <asm/ptrace.h>
+#include <asm/processor.h>
+#include <asm/current.h>
+#include <asm/msa.h>
+
+#ifdef CONFIG_MIPS_MT_FPAFF
+#include <asm/mips_mt.h>
+#endif
+
+/*
+ * This enum specifies a mode in which we want the FPU to operate, for cores
+ * which implement the Status.FR bit. Note that the bottom bit of the value
+ * purposefully matches the desired value of the Status.FR bit.
+ */
+enum fpu_mode {
+	FPU_32BIT = 0,		/* FR = 0 */
+	FPU_64BIT,		/* FR = 1, FRE = 0 */
+	FPU_AS_IS,
+	FPU_HYBRID,		/* FR = 1, FRE = 1 */
+
+#define FPU_FR_MASK		0x1
+};
+
+#ifdef CONFIG_MIPS_FP_SUPPORT
+
+extern void _save_fp(struct task_struct *);
+extern void _restore_fp(struct task_struct *);
+
+#define __disable_fpu()							\
+do {									\
+	clear_c0_status(ST0_CU1);					\
+	disable_fpu_hazard();						\
+} while (0)
+
+static inline int __enable_fpu(enum fpu_mode mode)
+{
+	int fr;
+
+	switch (mode) {
+	case FPU_AS_IS:
+		/* just enable the FPU in its current mode */
+		set_c0_status(ST0_CU1);
+		enable_fpu_hazard();
+		return 0;
+
+	case FPU_HYBRID:
+		if (!cpu_has_fre)
+			return SIGFPE;
+
+		/* set FRE */
+		set_c0_config5(MIPS_CONF5_FRE);
+		goto fr_common;
+
+	case FPU_64BIT:
+#if !(defined(CONFIG_CPU_MIPSR2) || defined(CONFIG_CPU_MIPSR5) || \
+      defined(CONFIG_CPU_MIPSR6) || defined(CONFIG_64BIT))
+		/* we only have a 32-bit FPU */
+		return SIGFPE;
+#endif
+		/* fallthrough */
+	case FPU_32BIT:
+		if (cpu_has_fre) {
+			/* clear FRE */
+			clear_c0_config5(MIPS_CONF5_FRE);
+		}
+fr_common:
+		/* set CU1 & change FR appropriately */
+		fr = (int)mode & FPU_FR_MASK;
+		change_c0_status(ST0_CU1 | ST0_FR, ST0_CU1 | (fr ? ST0_FR : 0));
+		enable_fpu_hazard();
+
+		/* check FR has the desired value */
+		if (!!(read_c0_status() & ST0_FR) == !!fr)
+			return 0;
+
+		/* unsupported FR value */
+		__disable_fpu();
+		return SIGFPE;
+
+	default:
+		BUG();
+	}
+
+	return SIGFPE;
+}
+
+#define clear_fpu_owner()	clear_thread_flag(TIF_USEDFPU)
+
+static inline int __is_fpu_owner(void)
+{
+	return test_thread_flag(TIF_USEDFPU);
+}
+
+static inline int is_fpu_owner(void)
+{
+	return cpu_has_fpu && __is_fpu_owner();
+}
+
+static inline int __own_fpu(void)
+{
+	enum fpu_mode mode;
+	int ret;
+
+	if (test_thread_flag(TIF_HYBRID_FPREGS))
+		mode = FPU_HYBRID;
+	else
+		mode = !test_thread_flag(TIF_32BIT_FPREGS);
+
+	ret = __enable_fpu(mode);
+	if (ret)
+		return ret;
+
+	KSTK_STATUS(current) |= ST0_CU1;
+	if (mode == FPU_64BIT || mode == FPU_HYBRID)
+		KSTK_STATUS(current) |= ST0_FR;
+	else /* mode == FPU_32BIT */
+		KSTK_STATUS(current) &= ~ST0_FR;
+
+	set_thread_flag(TIF_USEDFPU);
+	return 0;
+}
+
+static inline int own_fpu_inatomic(int restore)
+{
+	int ret = 0;
+
+	if (cpu_has_fpu && !__is_fpu_owner()) {
+		ret = __own_fpu();
+		if (restore && !ret)
+			_restore_fp(current);
+	}
+	return ret;
+}
+
+static inline int own_fpu(int restore)
+{
+	int ret;
+
+	preempt_disable();
+	ret = own_fpu_inatomic(restore);
+	preempt_enable();
+	return ret;
+}
+
+static inline void lose_fpu_inatomic(int save, struct task_struct *tsk)
+{
+	if (is_msa_enabled()) {
+		if (save) {
+			save_msa(tsk);
+			tsk->thread.fpu.fcr31 =
+					read_32bit_cp1_register(CP1_STATUS);
+		}
+		disable_msa();
+		clear_tsk_thread_flag(tsk, TIF_USEDMSA);
+		__disable_fpu();
+	} else if (is_fpu_owner()) {
+		if (save)
+			_save_fp(tsk);
+		__disable_fpu();
+	} else {
+		/* FPU should not have been left enabled with no owner */
+		WARN(read_c0_status() & ST0_CU1,
+		     "Orphaned FPU left enabled");
+	}
+	KSTK_STATUS(tsk) &= ~ST0_CU1;
+	clear_tsk_thread_flag(tsk, TIF_USEDFPU);
+}
+
+static inline void lose_fpu(int save)
+{
+	preempt_disable();
+	lose_fpu_inatomic(save, current);
+	preempt_enable();
+}
+
+/**
+ * init_fp_ctx() - Initialize task FP context
+ * @target: The task whose FP context should be initialized.
+ *
+ * Initializes the FP context of the target task to sane default values if that
+ * target task does not already have valid FP context. Once the context has
+ * been initialized, the task will be marked as having used FP & thus having
+ * valid FP context.
+ *
+ * Returns: true if context is initialized, else false.
+ */
+static inline bool init_fp_ctx(struct task_struct *target)
+{
+	/* If FP has been used then the target already has context */
+	if (tsk_used_math(target))
+		return false;
+
+	/* Begin with data registers set to all 1s... */
+	memset(&target->thread.fpu.fpr, ~0, sizeof(target->thread.fpu.fpr));
+
+	/* FCSR has been preset by `mips_set_personality_nan'.  */
+
+	/*
+	 * Record that the target has "used" math, such that the context
+	 * just initialised, and any modifications made by the caller,
+	 * aren't discarded.
+	 */
+	set_stopped_child_used_math(target);
+
+	return true;
+}
+
+static inline void save_fp(struct task_struct *tsk)
+{
+	if (cpu_has_fpu)
+		_save_fp(tsk);
+}
+
+static inline void restore_fp(struct task_struct *tsk)
+{
+	if (cpu_has_fpu)
+		_restore_fp(tsk);
+}
+
+static inline union fpureg *get_fpu_regs(struct task_struct *tsk)
+{
+	if (tsk == current) {
+		preempt_disable();
+		if (is_fpu_owner())
+			_save_fp(current);
+		preempt_enable();
+	}
+
+	return tsk->thread.fpu.fpr;
+}
+
+#else /* !CONFIG_MIPS_FP_SUPPORT */
+
+/*
+ * When FP support is disabled we provide only a minimal set of stub functions
+ * to avoid callers needing to care too much about CONFIG_MIPS_FP_SUPPORT.
+ */
+
+static inline int __enable_fpu(enum fpu_mode mode)
+{
+	return SIGILL;
+}
+
+static inline void __disable_fpu(void)
+{
+	/* no-op */
+}
+
+
+static inline int is_fpu_owner(void)
+{
+	return 0;
+}
+
+static inline void clear_fpu_owner(void)
+{
+	/* no-op */
+}
+
+static inline int own_fpu_inatomic(int restore)
+{
+	return SIGILL;
+}
+
+static inline int own_fpu(int restore)
+{
+	return SIGILL;
+}
+
+static inline void lose_fpu_inatomic(int save, struct task_struct *tsk)
+{
+	/* no-op */
+}
+
+static inline void lose_fpu(int save)
+{
+	/* no-op */
+}
+
+static inline bool init_fp_ctx(struct task_struct *target)
+{
+	return false;
+}
+
+/*
+ * The following functions should only be called in paths where we know that FP
+ * support is enabled, typically a path where own_fpu() or __enable_fpu() have
+ * returned successfully. When CONFIG_MIPS_FP_SUPPORT=n it is known at compile
+ * time that this should never happen, so calls to these functions should be
+ * optimized away & never actually be emitted.
+ */
+
+extern void save_fp(struct task_struct *tsk)
+	__compiletime_error("save_fp() should not be called when CONFIG_MIPS_FP_SUPPORT=n");
+
+extern void _save_fp(struct task_struct *)
+	__compiletime_error("_save_fp() should not be called when CONFIG_MIPS_FP_SUPPORT=n");
+
+extern void restore_fp(struct task_struct *tsk)
+	__compiletime_error("restore_fp() should not be called when CONFIG_MIPS_FP_SUPPORT=n");
+
+extern void _restore_fp(struct task_struct *)
+	__compiletime_error("_restore_fp() should not be called when CONFIG_MIPS_FP_SUPPORT=n");
+
+extern union fpureg *get_fpu_regs(struct task_struct *tsk)
+	__compiletime_error("get_fpu_regs() should not be called when CONFIG_MIPS_FP_SUPPORT=n");
+
+#endif /* !CONFIG_MIPS_FP_SUPPORT */
+#endif /* _ASM_FPU_H */
diff --git a/arch/mips/include/asm/fpu_emulator.h b/arch/mips/include/asm/fpu_emulator.h
new file mode 100644
index 000000000..f67759e81
--- /dev/null
+++ b/arch/mips/include/asm/fpu_emulator.h
@@ -0,0 +1,187 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *
+ * Further private data for which no space exists in mips_fpu_struct.
+ * This should be subsumed into the mips_fpu_struct structure as
+ * defined in processor.h as soon as the absurd wired absolute assembler
+ * offsets become dynamic at compile time.
+ *
+ * Kevin D. Kissell, kevink@mips.com and Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 2000 MIPS Technologies, Inc.  All rights reserved.
+ */
+#ifndef _ASM_FPU_EMULATOR_H
+#define _ASM_FPU_EMULATOR_H
+
+#include <linux/sched.h>
+#include <asm/dsemul.h>
+#include <asm/thread_info.h>
+#include <asm/inst.h>
+#include <asm/local.h>
+#include <asm/processor.h>
+
+#ifdef CONFIG_DEBUG_FS
+
+struct mips_fpu_emulator_stats {
+	unsigned long emulated;
+	unsigned long loads;
+	unsigned long stores;
+	unsigned long branches;
+	unsigned long cp1ops;
+	unsigned long cp1xops;
+	unsigned long errors;
+	unsigned long ieee754_inexact;
+	unsigned long ieee754_underflow;
+	unsigned long ieee754_overflow;
+	unsigned long ieee754_zerodiv;
+	unsigned long ieee754_invalidop;
+	unsigned long ds_emul;
+
+	unsigned long abs_s;
+	unsigned long abs_d;
+	unsigned long add_s;
+	unsigned long add_d;
+	unsigned long bc1eqz;
+	unsigned long bc1nez;
+	unsigned long ceil_w_s;
+	unsigned long ceil_w_d;
+	unsigned long ceil_l_s;
+	unsigned long ceil_l_d;
+	unsigned long class_s;
+	unsigned long class_d;
+	unsigned long cmp_af_s;
+	unsigned long cmp_af_d;
+	unsigned long cmp_eq_s;
+	unsigned long cmp_eq_d;
+	unsigned long cmp_le_s;
+	unsigned long cmp_le_d;
+	unsigned long cmp_lt_s;
+	unsigned long cmp_lt_d;
+	unsigned long cmp_ne_s;
+	unsigned long cmp_ne_d;
+	unsigned long cmp_or_s;
+	unsigned long cmp_or_d;
+	unsigned long cmp_ueq_s;
+	unsigned long cmp_ueq_d;
+	unsigned long cmp_ule_s;
+	unsigned long cmp_ule_d;
+	unsigned long cmp_ult_s;
+	unsigned long cmp_ult_d;
+	unsigned long cmp_un_s;
+	unsigned long cmp_un_d;
+	unsigned long cmp_une_s;
+	unsigned long cmp_une_d;
+	unsigned long cmp_saf_s;
+	unsigned long cmp_saf_d;
+	unsigned long cmp_seq_s;
+	unsigned long cmp_seq_d;
+	unsigned long cmp_sle_s;
+	unsigned long cmp_sle_d;
+	unsigned long cmp_slt_s;
+	unsigned long cmp_slt_d;
+	unsigned long cmp_sne_s;
+	unsigned long cmp_sne_d;
+	unsigned long cmp_sor_s;
+	unsigned long cmp_sor_d;
+	unsigned long cmp_sueq_s;
+	unsigned long cmp_sueq_d;
+	unsigned long cmp_sule_s;
+	unsigned long cmp_sule_d;
+	unsigned long cmp_sult_s;
+	unsigned long cmp_sult_d;
+	unsigned long cmp_sun_s;
+	unsigned long cmp_sun_d;
+	unsigned long cmp_sune_s;
+	unsigned long cmp_sune_d;
+	unsigned long cvt_d_l;
+	unsigned long cvt_d_s;
+	unsigned long cvt_d_w;
+	unsigned long cvt_l_s;
+	unsigned long cvt_l_d;
+	unsigned long cvt_s_d;
+	unsigned long cvt_s_l;
+	unsigned long cvt_s_w;
+	unsigned long cvt_w_s;
+	unsigned long cvt_w_d;
+	unsigned long div_s;
+	unsigned long div_d;
+	unsigned long floor_w_s;
+	unsigned long floor_w_d;
+	unsigned long floor_l_s;
+	unsigned long floor_l_d;
+	unsigned long maddf_s;
+	unsigned long maddf_d;
+	unsigned long max_s;
+	unsigned long max_d;
+	unsigned long maxa_s;
+	unsigned long maxa_d;
+	unsigned long min_s;
+	unsigned long min_d;
+	unsigned long mina_s;
+	unsigned long mina_d;
+	unsigned long mov_s;
+	unsigned long mov_d;
+	unsigned long msubf_s;
+	unsigned long msubf_d;
+	unsigned long mul_s;
+	unsigned long mul_d;
+	unsigned long neg_s;
+	unsigned long neg_d;
+	unsigned long recip_s;
+	unsigned long recip_d;
+	unsigned long rint_s;
+	unsigned long rint_d;
+	unsigned long round_w_s;
+	unsigned long round_w_d;
+	unsigned long round_l_s;
+	unsigned long round_l_d;
+	unsigned long rsqrt_s;
+	unsigned long rsqrt_d;
+	unsigned long sel_s;
+	unsigned long sel_d;
+	unsigned long seleqz_s;
+	unsigned long seleqz_d;
+	unsigned long selnez_s;
+	unsigned long selnez_d;
+	unsigned long sqrt_s;
+	unsigned long sqrt_d;
+	unsigned long sub_s;
+	unsigned long sub_d;
+	unsigned long trunc_w_s;
+	unsigned long trunc_w_d;
+	unsigned long trunc_l_s;
+	unsigned long trunc_l_d;
+};
+
+DECLARE_PER_CPU(struct mips_fpu_emulator_stats, fpuemustats);
+
+#define MIPS_FPU_EMU_INC_STATS(M)					\
+do {									\
+	preempt_disable();						\
+	__this_cpu_inc(fpuemustats.M);					\
+	preempt_enable();						\
+} while (0)
+
+#else
+#define MIPS_FPU_EMU_INC_STATS(M) do { } while (0)
+#endif /* CONFIG_DEBUG_FS */
+
+extern int fpu_emulator_cop1Handler(struct pt_regs *xcp,
+				    struct mips_fpu_struct *ctx, int has_fpu,
+				    void __user **fault_addr);
+void force_fcr31_sig(unsigned long fcr31, void __user *fault_addr,
+		     struct task_struct *tsk);
+int process_fpemu_return(int sig, void __user *fault_addr,
+			 unsigned long fcr31);
+
+/*
+ * Mask the FCSR Cause bits according to the Enable bits, observing
+ * that Unimplemented is always enabled.
+ */
+static inline unsigned long mask_fcr31_x(unsigned long fcr31)
+{
+	return fcr31 & (FPU_CSR_UNI_X |
+			((fcr31 & FPU_CSR_ALL_E) <<
+			 (ffs(FPU_CSR_ALL_X) - ffs(FPU_CSR_ALL_E))));
+}
+
+#endif /* _ASM_FPU_EMULATOR_H */
diff --git a/arch/mips/include/asm/ftrace.h b/arch/mips/include/asm/ftrace.h
new file mode 100644
index 000000000..db497a816
--- /dev/null
+++ b/arch/mips/include/asm/ftrace.h
@@ -0,0 +1,90 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive for
+ * more details.
+ *
+ * Copyright (C) 2009 DSLab, Lanzhou University, China
+ * Author: Wu Zhangjin <wuzhangjin@gmail.com>
+ */
+
+#ifndef _ASM_MIPS_FTRACE_H
+#define _ASM_MIPS_FTRACE_H
+
+#ifdef CONFIG_FUNCTION_TRACER
+
+#define MCOUNT_ADDR ((unsigned long)(_mcount))
+#define MCOUNT_INSN_SIZE 4		/* sizeof mcount call */
+
+#ifndef __ASSEMBLY__
+extern void _mcount(void);
+#define mcount _mcount
+
+#define safe_load(load, src, dst, error)		\
+do {							\
+	asm volatile (					\
+		"1: " load " %[tmp_dst], 0(%[tmp_src])\n"	\
+		"   li %[tmp_err], 0\n"			\
+		"2: .insn\n"				\
+							\
+		".section .fixup, \"ax\"\n"		\
+		"3: li %[tmp_err], 1\n"			\
+		"   j 2b\n"				\
+		".previous\n"				\
+							\
+		".section\t__ex_table,\"a\"\n\t"	\
+		STR(PTR_WD) "\t1b, 3b\n\t"		\
+		".previous\n"				\
+							\
+		: [tmp_dst] "=&r" (dst), [tmp_err] "=r" (error)\
+		: [tmp_src] "r" (src)			\
+		: "memory"				\
+	);						\
+} while (0)
+
+#define safe_store(store, src, dst, error)	\
+do {						\
+	asm volatile (				\
+		"1: " store " %[tmp_src], 0(%[tmp_dst])\n"\
+		"   li %[tmp_err], 0\n"		\
+		"2: .insn\n"			\
+						\
+		".section .fixup, \"ax\"\n"	\
+		"3: li %[tmp_err], 1\n"		\
+		"   j 2b\n"			\
+		".previous\n"			\
+						\
+		".section\t__ex_table,\"a\"\n\t"\
+		STR(PTR_WD) "\t1b, 3b\n\t"	\
+		".previous\n"			\
+						\
+		: [tmp_err] "=r" (error)	\
+		: [tmp_dst] "r" (dst), [tmp_src] "r" (src)\
+		: "memory"			\
+	);					\
+} while (0)
+
+#define safe_load_code(dst, src, error) \
+	safe_load(STR(lw), src, dst, error)
+#define safe_store_code(src, dst, error) \
+	safe_store(STR(sw), src, dst, error)
+
+#define safe_load_stack(dst, src, error) \
+	safe_load(STR(PTR_L), src, dst, error)
+
+#define safe_store_stack(src, dst, error) \
+	safe_store(STR(PTR_S), src, dst, error)
+
+
+#ifdef CONFIG_DYNAMIC_FTRACE
+static inline unsigned long ftrace_call_adjust(unsigned long addr)
+{
+	return addr;
+}
+
+struct dyn_arch_ftrace {
+};
+
+#endif /*  CONFIG_DYNAMIC_FTRACE */
+#endif /* __ASSEMBLY__ */
+#endif /* CONFIG_FUNCTION_TRACER */
+#endif /* _ASM_MIPS_FTRACE_H */
diff --git a/arch/mips/include/asm/futex.h b/arch/mips/include/asm/futex.h
new file mode 100644
index 000000000..05832eb24
--- /dev/null
+++ b/arch/mips/include/asm/futex.h
@@ -0,0 +1,210 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (c) 2006  Ralf Baechle (ralf@linux-mips.org)
+ */
+#ifndef _ASM_FUTEX_H
+#define _ASM_FUTEX_H
+
+#ifdef __KERNEL__
+
+#include <linux/futex.h>
+#include <linux/uaccess.h>
+#include <asm/asm-eva.h>
+#include <asm/barrier.h>
+#include <asm/compiler.h>
+#include <asm/errno.h>
+#include <asm/sync.h>
+
+#define arch_futex_atomic_op_inuser arch_futex_atomic_op_inuser
+#define futex_atomic_cmpxchg_inatomic futex_atomic_cmpxchg_inatomic
+#include <asm-generic/futex.h>
+
+#define __futex_atomic_op(op, insn, ret, oldval, uaddr, oparg)		\
+{									\
+	if (cpu_has_llsc && IS_ENABLED(CONFIG_WAR_R10000_LLSC)) {	\
+		__asm__ __volatile__(					\
+		"	.set	push				\n"	\
+		"	.set	noat				\n"	\
+		"	.set	push				\n"	\
+		"	.set	arch=r4000			\n"	\
+		"1:	ll	%1, %4	# __futex_atomic_op	\n"	\
+		"	.set	pop				\n"	\
+		"	" insn	"				\n"	\
+		"	.set	arch=r4000			\n"	\
+		"2:	sc	$1, %2				\n"	\
+		"	beqzl	$1, 1b				\n"	\
+		__stringify(__WEAK_LLSC_MB) "			\n"	\
+		"3:						\n"	\
+		"	.insn					\n"	\
+		"	.set	pop				\n"	\
+		"	.section .fixup,\"ax\"			\n"	\
+		"4:	li	%0, %6				\n"	\
+		"	j	3b				\n"	\
+		"	.previous				\n"	\
+		"	.section __ex_table,\"a\"		\n"	\
+		"	"__UA_ADDR "\t1b, 4b			\n"	\
+		"	"__UA_ADDR "\t2b, 4b			\n"	\
+		"	.previous				\n"	\
+		: "=r" (ret), "=&r" (oldval),				\
+		  "=" GCC_OFF_SMALL_ASM() (*uaddr)				\
+		: "0" (0), GCC_OFF_SMALL_ASM() (*uaddr), "Jr" (oparg),	\
+		  "i" (-EFAULT)						\
+		: "memory");						\
+	} else if (cpu_has_llsc) {					\
+		__asm__ __volatile__(					\
+		"	.set	push				\n"	\
+		"	.set	noat				\n"	\
+		"	.set	push				\n"	\
+		"	.set	"MIPS_ISA_ARCH_LEVEL"		\n"	\
+		"	" __SYNC(full, loongson3_war) "		\n"	\
+		"1:	"user_ll("%1", "%4")" # __futex_atomic_op\n"	\
+		"	.set	pop				\n"	\
+		"	" insn	"				\n"	\
+		"	.set	"MIPS_ISA_ARCH_LEVEL"		\n"	\
+		"2:	"user_sc("$1", "%2")"			\n"	\
+		"	beqz	$1, 1b				\n"	\
+		__stringify(__WEAK_LLSC_MB) "			\n"	\
+		"3:						\n"	\
+		"	.insn					\n"	\
+		"	.set	pop				\n"	\
+		"	.section .fixup,\"ax\"			\n"	\
+		"4:	li	%0, %6				\n"	\
+		"	j	3b				\n"	\
+		"	.previous				\n"	\
+		"	.section __ex_table,\"a\"		\n"	\
+		"	"__UA_ADDR "\t1b, 4b			\n"	\
+		"	"__UA_ADDR "\t2b, 4b			\n"	\
+		"	.previous				\n"	\
+		: "=r" (ret), "=&r" (oldval),				\
+		  "=" GCC_OFF_SMALL_ASM() (*uaddr)				\
+		: "0" (0), GCC_OFF_SMALL_ASM() (*uaddr), "Jr" (oparg),	\
+		  "i" (-EFAULT)						\
+		: "memory");						\
+	} else {							\
+		/* fallback for non-SMP */				\
+		ret = futex_atomic_op_inuser_local(op, oparg, oval, uaddr);	\
+	}								\
+}
+
+static inline int
+arch_futex_atomic_op_inuser(int op, int oparg, int *oval, u32 __user *uaddr)
+{
+	int oldval = 0, ret;
+
+	if (!access_ok(uaddr, sizeof(u32)))
+		return -EFAULT;
+
+	switch (op) {
+	case FUTEX_OP_SET:
+		__futex_atomic_op(op, "move $1, %z5", ret, oldval, uaddr, oparg);
+		break;
+
+	case FUTEX_OP_ADD:
+		__futex_atomic_op(op, "addu $1, %1, %z5",
+				  ret, oldval, uaddr, oparg);
+		break;
+	case FUTEX_OP_OR:
+		__futex_atomic_op(op, "or	$1, %1, %z5",
+				  ret, oldval, uaddr, oparg);
+		break;
+	case FUTEX_OP_ANDN:
+		__futex_atomic_op(op, "and	$1, %1, %z5",
+				  ret, oldval, uaddr, ~oparg);
+		break;
+	case FUTEX_OP_XOR:
+		__futex_atomic_op(op, "xor	$1, %1, %z5",
+				  ret, oldval, uaddr, oparg);
+		break;
+	default:
+		ret = -ENOSYS;
+	}
+
+	if (!ret)
+		*oval = oldval;
+
+	return ret;
+}
+
+static inline int
+futex_atomic_cmpxchg_inatomic(u32 *uval, u32 __user *uaddr,
+			      u32 oldval, u32 newval)
+{
+	int ret = 0;
+	u32 val;
+
+	if (!access_ok(uaddr, sizeof(u32)))
+		return -EFAULT;
+
+	if (cpu_has_llsc && IS_ENABLED(CONFIG_WAR_R10000_LLSC)) {
+		__asm__ __volatile__(
+		"# futex_atomic_cmpxchg_inatomic			\n"
+		"	.set	push					\n"
+		"	.set	noat					\n"
+		"	.set	push					\n"
+		"	.set	arch=r4000				\n"
+		"1:	ll	%1, %3					\n"
+		"	bne	%1, %z4, 3f				\n"
+		"	.set	pop					\n"
+		"	move	$1, %z5					\n"
+		"	.set	arch=r4000				\n"
+		"2:	sc	$1, %2					\n"
+		"	beqzl	$1, 1b					\n"
+		__stringify(__WEAK_LLSC_MB) "				\n"
+		"3:							\n"
+		"	.insn						\n"
+		"	.set	pop					\n"
+		"	.section .fixup,\"ax\"				\n"
+		"4:	li	%0, %6					\n"
+		"	j	3b					\n"
+		"	.previous					\n"
+		"	.section __ex_table,\"a\"			\n"
+		"	"__UA_ADDR "\t1b, 4b				\n"
+		"	"__UA_ADDR "\t2b, 4b				\n"
+		"	.previous					\n"
+		: "+r" (ret), "=&r" (val), "=" GCC_OFF_SMALL_ASM() (*uaddr)
+		: GCC_OFF_SMALL_ASM() (*uaddr), "Jr" (oldval), "Jr" (newval),
+		  "i" (-EFAULT)
+		: "memory");
+	} else if (cpu_has_llsc) {
+		__asm__ __volatile__(
+		"# futex_atomic_cmpxchg_inatomic			\n"
+		"	.set	push					\n"
+		"	.set	noat					\n"
+		"	.set	push					\n"
+		"	.set	"MIPS_ISA_ARCH_LEVEL"			\n"
+		"	" __SYNC(full, loongson3_war) "			\n"
+		"1:	"user_ll("%1", "%3")"				\n"
+		"	bne	%1, %z4, 3f				\n"
+		"	.set	pop					\n"
+		"	move	$1, %z5					\n"
+		"	.set	"MIPS_ISA_ARCH_LEVEL"			\n"
+		"2:	"user_sc("$1", "%2")"				\n"
+		"	beqz	$1, 1b					\n"
+		"3:	" __SYNC_ELSE(full, loongson3_war, __WEAK_LLSC_MB) "\n"
+		"	.insn						\n"
+		"	.set	pop					\n"
+		"	.section .fixup,\"ax\"				\n"
+		"4:	li	%0, %6					\n"
+		"	j	3b					\n"
+		"	.previous					\n"
+		"	.section __ex_table,\"a\"			\n"
+		"	"__UA_ADDR "\t1b, 4b				\n"
+		"	"__UA_ADDR "\t2b, 4b				\n"
+		"	.previous					\n"
+		: "+r" (ret), "=&r" (val), "=" GCC_OFF_SMALL_ASM() (*uaddr)
+		: GCC_OFF_SMALL_ASM() (*uaddr), "Jr" (oldval), "Jr" (newval),
+		  "i" (-EFAULT)
+		: "memory");
+	} else {
+		return futex_atomic_cmpxchg_inatomic_local(uval, uaddr, oldval, newval);
+	}
+
+	*uval = val;
+	return ret;
+}
+
+#endif
+#endif /* _ASM_FUTEX_H */
diff --git a/arch/mips/include/asm/fw/arc/hinv.h b/arch/mips/include/asm/fw/arc/hinv.h
new file mode 100644
index 000000000..d67b6a90f
--- /dev/null
+++ b/arch/mips/include/asm/fw/arc/hinv.h
@@ -0,0 +1,176 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * ARCS hardware/memory inventory/configuration and system ID definitions.
+ */
+#ifndef _ASM_ARC_HINV_H
+#define _ASM_ARC_HINV_H
+
+#include <asm/sgidefs.h>
+#include <asm/fw/arc/types.h>
+
+/* configuration query defines */
+typedef enum configclass {
+	SystemClass,
+	ProcessorClass,
+	CacheClass,
+#ifndef _NT_PROM
+	MemoryClass,
+	AdapterClass,
+	ControllerClass,
+	PeripheralClass
+#else	/* _NT_PROM */
+	AdapterClass,
+	ControllerClass,
+	PeripheralClass,
+	MemoryClass
+#endif	/* _NT_PROM */
+} CONFIGCLASS;
+
+typedef enum configtype {
+	ARC,
+	CPU,
+	FPU,
+	PrimaryICache,
+	PrimaryDCache,
+	SecondaryICache,
+	SecondaryDCache,
+	SecondaryCache,
+#ifndef _NT_PROM
+	Memory,
+#endif
+	EISAAdapter,
+	TCAdapter,
+	SCSIAdapter,
+	DTIAdapter,
+	MultiFunctionAdapter,
+	DiskController,
+	TapeController,
+	CDROMController,
+	WORMController,
+	SerialController,
+	NetworkController,
+	DisplayController,
+	ParallelController,
+	PointerController,
+	KeyboardController,
+	AudioController,
+	OtherController,
+	DiskPeripheral,
+	FloppyDiskPeripheral,
+	TapePeripheral,
+	ModemPeripheral,
+	MonitorPeripheral,
+	PrinterPeripheral,
+	PointerPeripheral,
+	KeyboardPeripheral,
+	TerminalPeripheral,
+	LinePeripheral,
+	NetworkPeripheral,
+#ifdef	_NT_PROM
+	Memory,
+#endif
+	OtherPeripheral,
+
+	/* new stuff for IP30 */
+	/* added without moving anything */
+	/* except ANONYMOUS. */
+
+	XTalkAdapter,
+	PCIAdapter,
+	GIOAdapter,
+	TPUAdapter,
+
+	Anonymous
+} CONFIGTYPE;
+
+typedef enum {
+	Failed = 1,
+	ReadOnly = 2,
+	Removable = 4,
+	ConsoleIn = 8,
+	ConsoleOut = 16,
+	Input = 32,
+	Output = 64
+} IDENTIFIERFLAG;
+
+#ifndef NULL			/* for GetChild(NULL); */
+#define NULL	0
+#endif
+
+union key_u {
+	struct {
+#ifdef	_MIPSEB
+		unsigned char  c_bsize;		/* block size in lines */
+		unsigned char  c_lsize;		/* line size in bytes/tag */
+		unsigned short c_size;		/* cache size in 4K pages */
+#else	/* _MIPSEL */
+		unsigned short c_size;		/* cache size in 4K pages */
+		unsigned char  c_lsize;		/* line size in bytes/tag */
+		unsigned char  c_bsize;		/* block size in lines */
+#endif	/* _MIPSEL */
+	} cache;
+	ULONG FullKey;
+};
+
+#if _MIPS_SIM == _MIPS_SIM_ABI64
+#define SGI_ARCS_VERS	64			/* sgi 64-bit version */
+#define SGI_ARCS_REV	0			/* rev .00 */
+#else
+#define SGI_ARCS_VERS	1			/* first version */
+#define SGI_ARCS_REV	10			/* rev .10, 3/04/92 */
+#endif
+
+typedef struct {
+	CONFIGCLASS	Class;
+	CONFIGTYPE	Type;
+	IDENTIFIERFLAG	Flags;
+	USHORT		Version;
+	USHORT		Revision;
+	ULONG		Key;
+	ULONG		AffinityMask;
+	ULONG		ConfigurationDataSize;
+	ULONG		IdentifierLength;
+	char		*Identifier;
+} COMPONENT;
+
+/* internal structure that holds pathname parsing data */
+struct cfgdata {
+	char *name;			/* full name */
+	int minlen;			/* minimum length to match */
+	CONFIGTYPE type;		/* type of token */
+};
+
+/* System ID */
+typedef struct {
+	CHAR VendorId[8];
+	CHAR ProductId[8];
+} SYSTEMID;
+
+/* memory query functions */
+typedef enum memorytype {
+	ExceptionBlock,
+	SPBPage,			/* ARCS == SystemParameterBlock */
+#ifndef _NT_PROM
+	FreeContiguous,
+	FreeMemory,
+	BadMemory,
+	LoadedProgram,
+	FirmwareTemporary,
+	FirmwarePermanent
+#else	/* _NT_PROM */
+	FreeMemory,
+	BadMemory,
+	LoadedProgram,
+	FirmwareTemporary,
+	FirmwarePermanent,
+	FreeContiguous
+#endif	/* _NT_PROM */
+} MEMORYTYPE;
+
+typedef struct {
+	MEMORYTYPE	Type;
+	LONG		BasePage;
+	LONG		PageCount;
+} MEMORYDESCRIPTOR;
+
+#endif /* _ASM_ARC_HINV_H */
diff --git a/arch/mips/include/asm/fw/arc/types.h b/arch/mips/include/asm/fw/arc/types.h
new file mode 100644
index 000000000..ad1638061
--- /dev/null
+++ b/arch/mips/include/asm/fw/arc/types.h
@@ -0,0 +1,86 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright 1999 Ralf Baechle (ralf@gnu.org)
+ * Copyright 1999 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_ARC_TYPES_H
+#define _ASM_ARC_TYPES_H
+
+
+#ifdef CONFIG_FW_ARC32
+
+typedef char		CHAR;
+typedef short		SHORT;
+typedef long		LARGE_INTEGER __attribute__ ((__mode__ (__DI__)));
+typedef long		LONG __attribute__ ((__mode__ (__SI__)));
+typedef unsigned char	UCHAR;
+typedef unsigned short	USHORT;
+typedef unsigned long	ULONG __attribute__ ((__mode__ (__SI__)));
+typedef void		VOID;
+
+/* The pointer types.  Note that we're using a 64-bit compiler but all
+   pointer in the ARC structures are only 32-bit, so we need some disgusting
+   workarounds.	 Keep your vomit bag handy.  */
+typedef LONG		_PCHAR;
+typedef LONG		_PSHORT;
+typedef LONG		_PLARGE_INTEGER;
+typedef LONG		_PLONG;
+typedef LONG		_PUCHAR;
+typedef LONG		_PUSHORT;
+typedef LONG		_PULONG;
+typedef LONG		_PVOID;
+
+#endif /* CONFIG_FW_ARC32 */
+
+#ifdef CONFIG_FW_ARC64
+
+typedef char		CHAR;
+typedef short		SHORT;
+typedef long		LARGE_INTEGER __attribute__ ((__mode__ (__DI__)));
+typedef long		LONG __attribute__ ((__mode__ (__DI__)));
+typedef unsigned char	UCHAR;
+typedef unsigned short	USHORT;
+typedef unsigned long	ULONG __attribute__ ((__mode__ (__DI__)));
+typedef void		VOID;
+
+/* The pointer types.  We're 64-bit and the firmware is also 64-bit, so
+   live is sane ...  */
+typedef CHAR		*_PCHAR;
+typedef SHORT		*_PSHORT;
+typedef LARGE_INTEGER	*_PLARGE_INTEGER;
+typedef LONG		*_PLONG;
+typedef UCHAR		*_PUCHAR;
+typedef USHORT		*_PUSHORT;
+typedef ULONG		*_PULONG;
+typedef VOID		*_PVOID;
+
+#endif /* CONFIG_FW_ARC64  */
+
+typedef CHAR		*PCHAR;
+typedef SHORT		*PSHORT;
+typedef LARGE_INTEGER	*PLARGE_INTEGER;
+typedef LONG		*PLONG;
+typedef UCHAR		*PUCHAR;
+typedef USHORT		*PUSHORT;
+typedef ULONG		*PULONG;
+typedef VOID		*PVOID;
+
+/*
+ * Return type of ArcGetDisplayStatus()
+ */
+typedef struct {
+	USHORT	CursorXPosition;
+	USHORT	CursorYPosition;
+	USHORT	CursorMaxXPosition;
+	USHORT	CursorMaxYPosition;
+	USHORT	ForegroundColor;
+	USHORT	BackgroundColor;
+	UCHAR	HighIntensity;
+	UCHAR	Underscored;
+	UCHAR	ReverseVideo;
+} DISPLAY_STATUS;
+
+#endif /* _ASM_ARC_TYPES_H */
diff --git a/arch/mips/include/asm/fw/cfe/cfe_api.h b/arch/mips/include/asm/fw/cfe/cfe_api.h
new file mode 100644
index 000000000..25df2f4de
--- /dev/null
+++ b/arch/mips/include/asm/fw/cfe/cfe_api.h
@@ -0,0 +1,111 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2000, 2001, 2002 Broadcom Corporation
+ */
+/*
+ * Broadcom Common Firmware Environment (CFE)
+ *
+ * This file contains declarations for doing callbacks to
+ * cfe from an application.  It should be the only header
+ * needed by the application to use this library
+ *
+ * Authors:  Mitch Lichtenberg, Chris Demetriou
+ */
+#ifndef CFE_API_H
+#define CFE_API_H
+
+#include <linux/types.h>
+#include <linux/string.h>
+
+typedef long intptr_t;
+
+
+/*
+ * Constants
+ */
+
+/* Seal indicating CFE's presence, passed to user program. */
+#define CFE_EPTSEAL 0x43464531
+
+#define CFE_MI_RESERVED 0	/* memory is reserved, do not use */
+#define CFE_MI_AVAILABLE 1	/* memory is available */
+
+#define CFE_FLG_WARMSTART     0x00000001
+#define CFE_FLG_FULL_ARENA    0x00000001
+#define CFE_FLG_ENV_PERMANENT 0x00000001
+
+#define CFE_CPU_CMD_START 1
+#define CFE_CPU_CMD_STOP 0
+
+#define CFE_STDHANDLE_CONSOLE	0
+
+#define CFE_DEV_NETWORK		1
+#define CFE_DEV_DISK		2
+#define CFE_DEV_FLASH		3
+#define CFE_DEV_SERIAL		4
+#define CFE_DEV_CPU		5
+#define CFE_DEV_NVRAM		6
+#define CFE_DEV_CLOCK		7
+#define CFE_DEV_OTHER		8
+#define CFE_DEV_MASK		0x0F
+
+#define CFE_CACHE_FLUSH_D	1
+#define CFE_CACHE_INVAL_I	2
+#define CFE_CACHE_INVAL_D	4
+#define CFE_CACHE_INVAL_L2	8
+
+#define CFE_FWI_64BIT		0x00000001
+#define CFE_FWI_32BIT		0x00000002
+#define CFE_FWI_RELOC		0x00000004
+#define CFE_FWI_UNCACHED	0x00000008
+#define CFE_FWI_MULTICPU	0x00000010
+#define CFE_FWI_FUNCSIM		0x00000020
+#define CFE_FWI_RTLSIM		0x00000040
+
+typedef struct {
+	int64_t fwi_version;		/* major, minor, eco version */
+	int64_t fwi_totalmem;		/* total installed mem */
+	int64_t fwi_flags;		/* various flags */
+	int64_t fwi_boardid;		/* board ID */
+	int64_t fwi_bootarea_va;	/* VA of boot area */
+	int64_t fwi_bootarea_pa;	/* PA of boot area */
+	int64_t fwi_bootarea_size;	/* size of boot area */
+} cfe_fwinfo_t;
+
+
+/*
+ * Defines and prototypes for functions which take no arguments.
+ */
+int64_t cfe_getticks(void);
+
+/*
+ * Defines and prototypes for the rest of the functions.
+ */
+int cfe_close(int handle);
+int cfe_cpu_start(int cpu, void (*fn) (void), long sp, long gp, long a1);
+int cfe_cpu_stop(int cpu);
+int cfe_enumenv(int idx, char *name, int namelen, char *val, int vallen);
+int cfe_enummem(int idx, int flags, uint64_t * start, uint64_t * length,
+		uint64_t * type);
+int cfe_exit(int warm, int status);
+int cfe_flushcache(int flg);
+int cfe_getdevinfo(char *name);
+int cfe_getenv(char *name, char *dest, int destlen);
+int cfe_getfwinfo(cfe_fwinfo_t * info);
+int cfe_getstdhandle(int flg);
+int cfe_init(uint64_t handle, uint64_t ept);
+int cfe_inpstat(int handle);
+int cfe_ioctl(int handle, unsigned int ioctlnum, unsigned char *buffer,
+	      int length, int *retlen, uint64_t offset);
+int cfe_open(char *name);
+int cfe_read(int handle, unsigned char *buffer, int length);
+int cfe_readblk(int handle, int64_t offset, unsigned char *buffer,
+		int length);
+int cfe_setenv(char *name, char *val);
+int cfe_write(int handle, const char *buffer, int length);
+int cfe_writeblk(int handle, int64_t offset, const char *buffer,
+		 int length);
+extern unsigned long cfe_seal;
+__printf(1, 2) void cfe_die(char *fmt, ...);
+
+#endif				/* CFE_API_H */
diff --git a/arch/mips/include/asm/fw/cfe/cfe_error.h b/arch/mips/include/asm/fw/cfe/cfe_error.h
new file mode 100644
index 000000000..2f04a39fd
--- /dev/null
+++ b/arch/mips/include/asm/fw/cfe/cfe_error.h
@@ -0,0 +1,67 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2000, 2001, 2002 Broadcom Corporation
+ */
+
+/*
+ * Broadcom Common Firmware Environment (CFE)
+ *
+ * CFE's global error code list is here.
+ *
+ * Author:  Mitch Lichtenberg
+ */
+
+#define CFE_OK			 0
+#define CFE_ERR			-1	/* generic error */
+#define CFE_ERR_INV_COMMAND	-2
+#define CFE_ERR_EOF		-3
+#define CFE_ERR_IOERR		-4
+#define CFE_ERR_NOMEM		-5
+#define CFE_ERR_DEVNOTFOUND	-6
+#define CFE_ERR_DEVOPEN		-7
+#define CFE_ERR_INV_PARAM	-8
+#define CFE_ERR_ENVNOTFOUND	-9
+#define CFE_ERR_ENVREADONLY	-10
+
+#define CFE_ERR_NOTELF		-11
+#define CFE_ERR_NOT32BIT	-12
+#define CFE_ERR_WRONGENDIAN	-13
+#define CFE_ERR_BADELFVERS	-14
+#define CFE_ERR_NOTMIPS		-15
+#define CFE_ERR_BADELFFMT	-16
+#define CFE_ERR_BADADDR		-17
+
+#define CFE_ERR_FILENOTFOUND	-18
+#define CFE_ERR_UNSUPPORTED	-19
+
+#define CFE_ERR_HOSTUNKNOWN	-20
+
+#define CFE_ERR_TIMEOUT		-21
+
+#define CFE_ERR_PROTOCOLERR	-22
+
+#define CFE_ERR_NETDOWN		-23
+#define CFE_ERR_NONAMESERVER	-24
+
+#define CFE_ERR_NOHANDLES	-25
+#define CFE_ERR_ALREADYBOUND	-26
+
+#define CFE_ERR_CANNOTSET	-27
+#define CFE_ERR_NOMORE		-28
+#define CFE_ERR_BADFILESYS	-29
+#define CFE_ERR_FSNOTAVAIL	-30
+
+#define CFE_ERR_INVBOOTBLOCK	-31
+#define CFE_ERR_WRONGDEVTYPE	-32
+#define CFE_ERR_BBCHECKSUM	-33
+#define CFE_ERR_BOOTPROGCHKSUM	-34
+
+#define CFE_ERR_LDRNOTAVAIL	-35
+
+#define CFE_ERR_NOTREADY	-36
+
+#define CFE_ERR_GETMEM		-37
+#define CFE_ERR_SETMEM		-38
+
+#define CFE_ERR_NOTCONN		-39
+#define CFE_ERR_ADDRINUSE	-40
diff --git a/arch/mips/include/asm/fw/fw.h b/arch/mips/include/asm/fw/fw.h
new file mode 100644
index 000000000..d0494ce4b
--- /dev/null
+++ b/arch/mips/include/asm/fw/fw.h
@@ -0,0 +1,31 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2012 MIPS Technologies, Inc.
+ */
+#ifndef __ASM_FW_H_
+#define __ASM_FW_H_
+
+#include <asm/bootinfo.h>	/* For cleaner code... */
+
+extern int fw_argc;
+extern int *_fw_argv;
+extern int *_fw_envp;
+
+/*
+ * Most firmware like YAMON, PMON, etc. pass arguments and environment
+ * variables as 32-bit pointers. These take care of sign extension.
+ */
+#define fw_argv(index)		((char *)(long)_fw_argv[(index)])
+#define fw_envp(index)		((char *)(long)_fw_envp[(index)])
+
+extern void fw_init_cmdline(void);
+extern char *fw_getcmdline(void);
+extern void fw_meminit(void);
+extern char *fw_getenv(char *name);
+extern unsigned long fw_getenvl(char *name);
+extern void fw_init_early_console(void);
+
+#endif /* __ASM_FW_H_ */
diff --git a/arch/mips/include/asm/ginvt.h b/arch/mips/include/asm/ginvt.h
new file mode 100644
index 000000000..87b2974ff
--- /dev/null
+++ b/arch/mips/include/asm/ginvt.h
@@ -0,0 +1,59 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __MIPS_ASM_GINVT_H__
+#define __MIPS_ASM_GINVT_H__
+
+#include <asm/mipsregs.h>
+
+enum ginvt_type {
+	GINVT_FULL,
+	GINVT_VA,
+	GINVT_MMID,
+};
+
+#ifdef TOOLCHAIN_SUPPORTS_GINV
+# define _ASM_SET_GINV	".set	ginv\n"
+# define _ASM_UNSET_GINV
+#else
+# define _ASM_SET_GINV							\
+	_ASM_MACRO_1R1I(ginvt, rs, type,				\
+			_ASM_INSN_IF_MIPS(0x7c0000bd | (__rs << 21) | (\\type << 8))	\
+			_ASM_INSN32_IF_MM(0x0000717c | (__rs << 16) | (\\type << 9)))
+# define _ASM_UNSET_GINV ".purgem ginvt\n"
+#endif
+
+static __always_inline void ginvt(unsigned long addr, enum ginvt_type type)
+{
+	asm volatile(
+		".set	push\n"
+		_ASM_SET_GINV
+		"	ginvt	%0, %1\n"
+		_ASM_UNSET_GINV
+		".set	pop"
+		: /* no outputs */
+		: "r"(addr), "i"(type)
+		: "memory");
+}
+
+static inline void ginvt_full(void)
+{
+	ginvt(0, GINVT_FULL);
+}
+
+static inline void ginvt_va(unsigned long addr)
+{
+	addr &= PAGE_MASK << 1;
+	ginvt(addr, GINVT_VA);
+}
+
+static inline void ginvt_mmid(void)
+{
+	ginvt(0, GINVT_MMID);
+}
+
+static inline void ginvt_va_mmid(unsigned long addr)
+{
+	addr &= PAGE_MASK << 1;
+	ginvt(addr, GINVT_VA | GINVT_MMID);
+}
+
+#endif /* __MIPS_ASM_GINVT_H__ */
diff --git a/arch/mips/include/asm/gio_device.h b/arch/mips/include/asm/gio_device.h
new file mode 100644
index 000000000..159087f53
--- /dev/null
+++ b/arch/mips/include/asm/gio_device.h
@@ -0,0 +1,53 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#include <linux/device.h>
+#include <linux/mod_devicetable.h>
+
+struct gio_device_id {
+	__u8 id;
+};
+
+struct gio_device {
+	struct device	dev;
+	struct resource resource;
+	unsigned int	irq;
+	unsigned int	slotno;
+
+	const char	*name;
+	struct gio_device_id id;
+	unsigned	id32:1;
+	unsigned	gio64:1;
+};
+#define to_gio_device(d) container_of(d, struct gio_device, dev)
+
+struct gio_driver {
+	const char    *name;
+	struct module *owner;
+	const struct gio_device_id *id_table;
+
+	int  (*probe)(struct gio_device *, const struct gio_device_id *);
+	void (*remove)(struct gio_device *);
+	void (*shutdown)(struct gio_device *);
+
+	struct device_driver driver;
+};
+#define to_gio_driver(drv) container_of(drv, struct gio_driver, driver)
+
+extern struct gio_device *gio_dev_get(struct gio_device *);
+extern void gio_dev_put(struct gio_device *);
+
+extern int gio_device_register(struct gio_device *);
+extern void gio_device_unregister(struct gio_device *);
+extern void gio_release_dev(struct device *);
+
+static inline void gio_device_free(struct gio_device *dev)
+{
+	gio_release_dev(&dev->dev);
+}
+
+extern int gio_register_driver(struct gio_driver *);
+extern void gio_unregister_driver(struct gio_driver *);
+
+#define gio_get_drvdata(_dev)	     dev_get_drvdata(&(_dev)->dev)
+#define gio_set_drvdata(_dev, data)  dev_set_drvdata(&(_dev)->dev, (data))
+
+extern void gio_set_master(struct gio_device *);
diff --git a/arch/mips/include/asm/gt64120.h b/arch/mips/include/asm/gt64120.h
new file mode 100644
index 000000000..5d68d7265
--- /dev/null
+++ b/arch/mips/include/asm/gt64120.h
@@ -0,0 +1,566 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (C) 2000, 2004, 2005  MIPS Technologies, Inc.
+ *	All rights reserved.
+ *	Authors: Carsten Langgaard <carstenl@mips.com>
+ *		 Maciej W. Rozycki <macro@mips.com>
+ * Copyright (C) 2005 Ralf Baechle (ralf@linux-mips.org)
+ */
+#ifndef _ASM_GT64120_H
+#define _ASM_GT64120_H
+
+#include <asm/addrspace.h>
+#include <asm/byteorder.h>
+
+#define MSK(n)			((1 << (n)) - 1)
+
+/*
+ *  Register offset addresses
+ */
+/* CPU Configuration.  */
+#define GT_CPU_OFS		0x000
+
+#define GT_MULTI_OFS		0x120
+
+/* CPU Address Decode.	*/
+#define GT_SCS10LD_OFS		0x008
+#define GT_SCS10HD_OFS		0x010
+#define GT_SCS32LD_OFS		0x018
+#define GT_SCS32HD_OFS		0x020
+#define GT_CS20LD_OFS		0x028
+#define GT_CS20HD_OFS		0x030
+#define GT_CS3BOOTLD_OFS	0x038
+#define GT_CS3BOOTHD_OFS	0x040
+#define GT_PCI0IOLD_OFS		0x048
+#define GT_PCI0IOHD_OFS		0x050
+#define GT_PCI0M0LD_OFS		0x058
+#define GT_PCI0M0HD_OFS		0x060
+#define GT_ISD_OFS		0x068
+
+#define GT_PCI0M1LD_OFS		0x080
+#define GT_PCI0M1HD_OFS		0x088
+#define GT_PCI1IOLD_OFS		0x090
+#define GT_PCI1IOHD_OFS		0x098
+#define GT_PCI1M0LD_OFS		0x0a0
+#define GT_PCI1M0HD_OFS		0x0a8
+#define GT_PCI1M1LD_OFS		0x0b0
+#define GT_PCI1M1HD_OFS		0x0b8
+#define GT_PCI1M1LD_OFS		0x0b0
+#define GT_PCI1M1HD_OFS		0x0b8
+
+#define GT_SCS10AR_OFS		0x0d0
+#define GT_SCS32AR_OFS		0x0d8
+#define GT_CS20R_OFS		0x0e0
+#define GT_CS3BOOTR_OFS		0x0e8
+
+#define GT_PCI0IOREMAP_OFS	0x0f0
+#define GT_PCI0M0REMAP_OFS	0x0f8
+#define GT_PCI0M1REMAP_OFS	0x100
+#define GT_PCI1IOREMAP_OFS	0x108
+#define GT_PCI1M0REMAP_OFS	0x110
+#define GT_PCI1M1REMAP_OFS	0x118
+
+/* CPU Error Report.  */
+#define GT_CPUERR_ADDRLO_OFS	0x070
+#define GT_CPUERR_ADDRHI_OFS	0x078
+
+#define GT_CPUERR_DATALO_OFS	0x128			/* GT-64120A only  */
+#define GT_CPUERR_DATAHI_OFS	0x130			/* GT-64120A only  */
+#define GT_CPUERR_PARITY_OFS	0x138			/* GT-64120A only  */
+
+/* CPU Sync Barrier.  */
+#define GT_PCI0SYNC_OFS		0x0c0
+#define GT_PCI1SYNC_OFS		0x0c8
+
+/* SDRAM and Device Address Decode.  */
+#define GT_SCS0LD_OFS		0x400
+#define GT_SCS0HD_OFS		0x404
+#define GT_SCS1LD_OFS		0x408
+#define GT_SCS1HD_OFS		0x40c
+#define GT_SCS2LD_OFS		0x410
+#define GT_SCS2HD_OFS		0x414
+#define GT_SCS3LD_OFS		0x418
+#define GT_SCS3HD_OFS		0x41c
+#define GT_CS0LD_OFS		0x420
+#define GT_CS0HD_OFS		0x424
+#define GT_CS1LD_OFS		0x428
+#define GT_CS1HD_OFS		0x42c
+#define GT_CS2LD_OFS		0x430
+#define GT_CS2HD_OFS		0x434
+#define GT_CS3LD_OFS		0x438
+#define GT_CS3HD_OFS		0x43c
+#define GT_BOOTLD_OFS		0x440
+#define GT_BOOTHD_OFS		0x444
+
+#define GT_ADERR_OFS		0x470
+
+/* SDRAM Configuration.	 */
+#define GT_SDRAM_CFG_OFS	0x448
+
+#define GT_SDRAM_OPMODE_OFS	0x474
+#define GT_SDRAM_BM_OFS		0x478
+#define GT_SDRAM_ADDRDECODE_OFS 0x47c
+
+/* SDRAM Parameters.  */
+#define GT_SDRAM_B0_OFS		0x44c
+#define GT_SDRAM_B1_OFS		0x450
+#define GT_SDRAM_B2_OFS		0x454
+#define GT_SDRAM_B3_OFS		0x458
+
+/* Device Parameters.  */
+#define GT_DEV_B0_OFS		0x45c
+#define GT_DEV_B1_OFS		0x460
+#define GT_DEV_B2_OFS		0x464
+#define GT_DEV_B3_OFS		0x468
+#define GT_DEV_BOOT_OFS		0x46c
+
+/* ECC.	 */
+#define GT_ECC_ERRDATALO	0x480			/* GT-64120A only  */
+#define GT_ECC_ERRDATAHI	0x484			/* GT-64120A only  */
+#define GT_ECC_MEM		0x488			/* GT-64120A only  */
+#define GT_ECC_CALC		0x48c			/* GT-64120A only  */
+#define GT_ECC_ERRADDR		0x490			/* GT-64120A only  */
+
+/* DMA Record.	*/
+#define GT_DMA0_CNT_OFS		0x800
+#define GT_DMA1_CNT_OFS		0x804
+#define GT_DMA2_CNT_OFS		0x808
+#define GT_DMA3_CNT_OFS		0x80c
+#define GT_DMA0_SA_OFS		0x810
+#define GT_DMA1_SA_OFS		0x814
+#define GT_DMA2_SA_OFS		0x818
+#define GT_DMA3_SA_OFS		0x81c
+#define GT_DMA0_DA_OFS		0x820
+#define GT_DMA1_DA_OFS		0x824
+#define GT_DMA2_DA_OFS		0x828
+#define GT_DMA3_DA_OFS		0x82c
+#define GT_DMA0_NEXT_OFS	0x830
+#define GT_DMA1_NEXT_OFS	0x834
+#define GT_DMA2_NEXT_OFS	0x838
+#define GT_DMA3_NEXT_OFS	0x83c
+
+#define GT_DMA0_CUR_OFS		0x870
+#define GT_DMA1_CUR_OFS		0x874
+#define GT_DMA2_CUR_OFS		0x878
+#define GT_DMA3_CUR_OFS		0x87c
+
+/* DMA Channel Control.	 */
+#define GT_DMA0_CTRL_OFS	0x840
+#define GT_DMA1_CTRL_OFS	0x844
+#define GT_DMA2_CTRL_OFS	0x848
+#define GT_DMA3_CTRL_OFS	0x84c
+
+/* DMA Arbiter.	 */
+#define GT_DMA_ARB_OFS		0x860
+
+/* Timer/Counter.  */
+#define GT_TC0_OFS		0x850
+#define GT_TC1_OFS		0x854
+#define GT_TC2_OFS		0x858
+#define GT_TC3_OFS		0x85c
+
+#define GT_TC_CONTROL_OFS	0x864
+
+/* PCI Internal.  */
+#define GT_PCI0_CMD_OFS		0xc00
+#define GT_PCI0_TOR_OFS		0xc04
+#define GT_PCI0_BS_SCS10_OFS	0xc08
+#define GT_PCI0_BS_SCS32_OFS	0xc0c
+#define GT_PCI0_BS_CS20_OFS	0xc10
+#define GT_PCI0_BS_CS3BT_OFS	0xc14
+
+#define GT_PCI1_IACK_OFS	0xc30
+#define GT_PCI0_IACK_OFS	0xc34
+
+#define GT_PCI0_BARE_OFS	0xc3c
+#define GT_PCI0_PREFMBR_OFS	0xc40
+
+#define GT_PCI0_SCS10_BAR_OFS	0xc48
+#define GT_PCI0_SCS32_BAR_OFS	0xc4c
+#define GT_PCI0_CS20_BAR_OFS	0xc50
+#define GT_PCI0_CS3BT_BAR_OFS	0xc54
+#define GT_PCI0_SSCS10_BAR_OFS	0xc58
+#define GT_PCI0_SSCS32_BAR_OFS	0xc5c
+
+#define GT_PCI0_SCS3BT_BAR_OFS	0xc64
+
+#define GT_PCI1_CMD_OFS		0xc80
+#define GT_PCI1_TOR_OFS		0xc84
+#define GT_PCI1_BS_SCS10_OFS	0xc88
+#define GT_PCI1_BS_SCS32_OFS	0xc8c
+#define GT_PCI1_BS_CS20_OFS	0xc90
+#define GT_PCI1_BS_CS3BT_OFS	0xc94
+
+#define GT_PCI1_BARE_OFS	0xcbc
+#define GT_PCI1_PREFMBR_OFS	0xcc0
+
+#define GT_PCI1_SCS10_BAR_OFS	0xcc8
+#define GT_PCI1_SCS32_BAR_OFS	0xccc
+#define GT_PCI1_CS20_BAR_OFS	0xcd0
+#define GT_PCI1_CS3BT_BAR_OFS	0xcd4
+#define GT_PCI1_SSCS10_BAR_OFS	0xcd8
+#define GT_PCI1_SSCS32_BAR_OFS	0xcdc
+
+#define GT_PCI1_SCS3BT_BAR_OFS	0xce4
+
+#define GT_PCI1_CFGADDR_OFS	0xcf0
+#define GT_PCI1_CFGDATA_OFS	0xcf4
+#define GT_PCI0_CFGADDR_OFS	0xcf8
+#define GT_PCI0_CFGDATA_OFS	0xcfc
+
+/* Interrupts.	*/
+#define GT_INTRCAUSE_OFS	0xc18
+#define GT_INTRMASK_OFS		0xc1c
+
+#define GT_PCI0_ICMASK_OFS	0xc24
+#define GT_PCI0_SERR0MASK_OFS	0xc28
+
+#define GT_CPU_INTSEL_OFS	0xc70
+#define GT_PCI0_INTSEL_OFS	0xc74
+
+#define GT_HINTRCAUSE_OFS	0xc98
+#define GT_HINTRMASK_OFS	0xc9c
+
+#define GT_PCI0_HICMASK_OFS	0xca4
+#define GT_PCI1_SERR1MASK_OFS	0xca8
+
+
+/*
+ * I2O Support Registers
+ */
+#define INBOUND_MESSAGE_REGISTER0_PCI_SIDE		0x010
+#define INBOUND_MESSAGE_REGISTER1_PCI_SIDE		0x014
+#define OUTBOUND_MESSAGE_REGISTER0_PCI_SIDE		0x018
+#define OUTBOUND_MESSAGE_REGISTER1_PCI_SIDE		0x01c
+#define INBOUND_DOORBELL_REGISTER_PCI_SIDE		0x020
+#define INBOUND_INTERRUPT_CAUSE_REGISTER_PCI_SIDE	0x024
+#define INBOUND_INTERRUPT_MASK_REGISTER_PCI_SIDE	0x028
+#define OUTBOUND_DOORBELL_REGISTER_PCI_SIDE		0x02c
+#define OUTBOUND_INTERRUPT_CAUSE_REGISTER_PCI_SIDE	0x030
+#define OUTBOUND_INTERRUPT_MASK_REGISTER_PCI_SIDE	0x034
+#define INBOUND_QUEUE_PORT_VIRTUAL_REGISTER_PCI_SIDE	0x040
+#define OUTBOUND_QUEUE_PORT_VIRTUAL_REGISTER_PCI_SIDE	0x044
+#define QUEUE_CONTROL_REGISTER_PCI_SIDE			0x050
+#define QUEUE_BASE_ADDRESS_REGISTER_PCI_SIDE		0x054
+#define INBOUND_FREE_HEAD_POINTER_REGISTER_PCI_SIDE	0x060
+#define INBOUND_FREE_TAIL_POINTER_REGISTER_PCI_SIDE	0x064
+#define INBOUND_POST_HEAD_POINTER_REGISTER_PCI_SIDE	0x068
+#define INBOUND_POST_TAIL_POINTER_REGISTER_PCI_SIDE	0x06c
+#define OUTBOUND_FREE_HEAD_POINTER_REGISTER_PCI_SIDE	0x070
+#define OUTBOUND_FREE_TAIL_POINTER_REGISTER_PCI_SIDE	0x074
+#define OUTBOUND_POST_HEAD_POINTER_REGISTER_PCI_SIDE	0x078
+#define OUTBOUND_POST_TAIL_POINTER_REGISTER_PCI_SIDE	0x07c
+
+#define INBOUND_MESSAGE_REGISTER0_CPU_SIDE		0x1c10
+#define INBOUND_MESSAGE_REGISTER1_CPU_SIDE		0x1c14
+#define OUTBOUND_MESSAGE_REGISTER0_CPU_SIDE		0x1c18
+#define OUTBOUND_MESSAGE_REGISTER1_CPU_SIDE		0x1c1c
+#define INBOUND_DOORBELL_REGISTER_CPU_SIDE		0x1c20
+#define INBOUND_INTERRUPT_CAUSE_REGISTER_CPU_SIDE	0x1c24
+#define INBOUND_INTERRUPT_MASK_REGISTER_CPU_SIDE	0x1c28
+#define OUTBOUND_DOORBELL_REGISTER_CPU_SIDE		0x1c2c
+#define OUTBOUND_INTERRUPT_CAUSE_REGISTER_CPU_SIDE	0x1c30
+#define OUTBOUND_INTERRUPT_MASK_REGISTER_CPU_SIDE	0x1c34
+#define INBOUND_QUEUE_PORT_VIRTUAL_REGISTER_CPU_SIDE	0x1c40
+#define OUTBOUND_QUEUE_PORT_VIRTUAL_REGISTER_CPU_SIDE	0x1c44
+#define QUEUE_CONTROL_REGISTER_CPU_SIDE			0x1c50
+#define QUEUE_BASE_ADDRESS_REGISTER_CPU_SIDE		0x1c54
+#define INBOUND_FREE_HEAD_POINTER_REGISTER_CPU_SIDE	0x1c60
+#define INBOUND_FREE_TAIL_POINTER_REGISTER_CPU_SIDE	0x1c64
+#define INBOUND_POST_HEAD_POINTER_REGISTER_CPU_SIDE	0x1c68
+#define INBOUND_POST_TAIL_POINTER_REGISTER_CPU_SIDE	0x1c6c
+#define OUTBOUND_FREE_HEAD_POINTER_REGISTER_CPU_SIDE	0x1c70
+#define OUTBOUND_FREE_TAIL_POINTER_REGISTER_CPU_SIDE	0x1c74
+#define OUTBOUND_POST_HEAD_POINTER_REGISTER_CPU_SIDE	0x1c78
+#define OUTBOUND_POST_TAIL_POINTER_REGISTER_CPU_SIDE	0x1c7c
+
+/*
+ *  Register encodings
+ */
+#define GT_CPU_ENDIAN_SHF	12
+#define GT_CPU_ENDIAN_MSK	(MSK(1) << GT_CPU_ENDIAN_SHF)
+#define GT_CPU_ENDIAN_BIT	GT_CPU_ENDIAN_MSK
+#define GT_CPU_WR_SHF		16
+#define GT_CPU_WR_MSK		(MSK(1) << GT_CPU_WR_SHF)
+#define GT_CPU_WR_BIT		GT_CPU_WR_MSK
+#define GT_CPU_WR_DXDXDXDX	0
+#define GT_CPU_WR_DDDD		1
+
+
+#define GT_PCI_DCRM_SHF		21
+#define GT_PCI_LD_SHF		0
+#define GT_PCI_LD_MSK		(MSK(15) << GT_PCI_LD_SHF)
+#define GT_PCI_HD_SHF		0
+#define GT_PCI_HD_MSK		(MSK(7) << GT_PCI_HD_SHF)
+#define GT_PCI_REMAP_SHF	0
+#define GT_PCI_REMAP_MSK	(MSK(11) << GT_PCI_REMAP_SHF)
+
+
+#define GT_CFGADDR_CFGEN_SHF	31
+#define GT_CFGADDR_CFGEN_MSK	(MSK(1) << GT_CFGADDR_CFGEN_SHF)
+#define GT_CFGADDR_CFGEN_BIT	GT_CFGADDR_CFGEN_MSK
+
+#define GT_CFGADDR_BUSNUM_SHF	16
+#define GT_CFGADDR_BUSNUM_MSK	(MSK(8) << GT_CFGADDR_BUSNUM_SHF)
+
+#define GT_CFGADDR_DEVNUM_SHF	11
+#define GT_CFGADDR_DEVNUM_MSK	(MSK(5) << GT_CFGADDR_DEVNUM_SHF)
+
+#define GT_CFGADDR_FUNCNUM_SHF	8
+#define GT_CFGADDR_FUNCNUM_MSK	(MSK(3) << GT_CFGADDR_FUNCNUM_SHF)
+
+#define GT_CFGADDR_REGNUM_SHF	2
+#define GT_CFGADDR_REGNUM_MSK	(MSK(6) << GT_CFGADDR_REGNUM_SHF)
+
+
+#define GT_SDRAM_BM_ORDER_SHF	2
+#define GT_SDRAM_BM_ORDER_MSK	(MSK(1) << GT_SDRAM_BM_ORDER_SHF)
+#define GT_SDRAM_BM_ORDER_BIT	GT_SDRAM_BM_ORDER_MSK
+#define GT_SDRAM_BM_ORDER_SUB	1
+#define GT_SDRAM_BM_ORDER_LIN	0
+
+#define GT_SDRAM_BM_RSVD_ALL1	0xffb
+
+
+#define GT_SDRAM_ADDRDECODE_ADDR_SHF	0
+#define GT_SDRAM_ADDRDECODE_ADDR_MSK	(MSK(3) << GT_SDRAM_ADDRDECODE_ADDR_SHF)
+#define GT_SDRAM_ADDRDECODE_ADDR_0	0
+#define GT_SDRAM_ADDRDECODE_ADDR_1	1
+#define GT_SDRAM_ADDRDECODE_ADDR_2	2
+#define GT_SDRAM_ADDRDECODE_ADDR_3	3
+#define GT_SDRAM_ADDRDECODE_ADDR_4	4
+#define GT_SDRAM_ADDRDECODE_ADDR_5	5
+#define GT_SDRAM_ADDRDECODE_ADDR_6	6
+#define GT_SDRAM_ADDRDECODE_ADDR_7	7
+
+
+#define GT_SDRAM_B0_CASLAT_SHF		0
+#define GT_SDRAM_B0_CASLAT_MSK		(MSK(2) << GT_SDRAM_B0__SHF)
+#define GT_SDRAM_B0_CASLAT_2		1
+#define GT_SDRAM_B0_CASLAT_3		2
+
+#define GT_SDRAM_B0_FTDIS_SHF		2
+#define GT_SDRAM_B0_FTDIS_MSK		(MSK(1) << GT_SDRAM_B0_FTDIS_SHF)
+#define GT_SDRAM_B0_FTDIS_BIT		GT_SDRAM_B0_FTDIS_MSK
+
+#define GT_SDRAM_B0_SRASPRCHG_SHF	3
+#define GT_SDRAM_B0_SRASPRCHG_MSK	(MSK(1) << GT_SDRAM_B0_SRASPRCHG_SHF)
+#define GT_SDRAM_B0_SRASPRCHG_BIT	GT_SDRAM_B0_SRASPRCHG_MSK
+#define GT_SDRAM_B0_SRASPRCHG_2		0
+#define GT_SDRAM_B0_SRASPRCHG_3		1
+
+#define GT_SDRAM_B0_B0COMPAB_SHF	4
+#define GT_SDRAM_B0_B0COMPAB_MSK	(MSK(1) << GT_SDRAM_B0_B0COMPAB_SHF)
+#define GT_SDRAM_B0_B0COMPAB_BIT	GT_SDRAM_B0_B0COMPAB_MSK
+
+#define GT_SDRAM_B0_64BITINT_SHF	5
+#define GT_SDRAM_B0_64BITINT_MSK	(MSK(1) << GT_SDRAM_B0_64BITINT_SHF)
+#define GT_SDRAM_B0_64BITINT_BIT	GT_SDRAM_B0_64BITINT_MSK
+#define GT_SDRAM_B0_64BITINT_2		0
+#define GT_SDRAM_B0_64BITINT_4		1
+
+#define GT_SDRAM_B0_BW_SHF		6
+#define GT_SDRAM_B0_BW_MSK		(MSK(1) << GT_SDRAM_B0_BW_SHF)
+#define GT_SDRAM_B0_BW_BIT		GT_SDRAM_B0_BW_MSK
+#define GT_SDRAM_B0_BW_32		0
+#define GT_SDRAM_B0_BW_64		1
+
+#define GT_SDRAM_B0_BLODD_SHF		7
+#define GT_SDRAM_B0_BLODD_MSK		(MSK(1) << GT_SDRAM_B0_BLODD_SHF)
+#define GT_SDRAM_B0_BLODD_BIT		GT_SDRAM_B0_BLODD_MSK
+
+#define GT_SDRAM_B0_PAR_SHF		8
+#define GT_SDRAM_B0_PAR_MSK		(MSK(1) << GT_SDRAM_B0_PAR_SHF)
+#define GT_SDRAM_B0_PAR_BIT		GT_SDRAM_B0_PAR_MSK
+
+#define GT_SDRAM_B0_BYPASS_SHF		9
+#define GT_SDRAM_B0_BYPASS_MSK		(MSK(1) << GT_SDRAM_B0_BYPASS_SHF)
+#define GT_SDRAM_B0_BYPASS_BIT		GT_SDRAM_B0_BYPASS_MSK
+
+#define GT_SDRAM_B0_SRAS2SCAS_SHF	10
+#define GT_SDRAM_B0_SRAS2SCAS_MSK	(MSK(1) << GT_SDRAM_B0_SRAS2SCAS_SHF)
+#define GT_SDRAM_B0_SRAS2SCAS_BIT	GT_SDRAM_B0_SRAS2SCAS_MSK
+#define GT_SDRAM_B0_SRAS2SCAS_2		0
+#define GT_SDRAM_B0_SRAS2SCAS_3		1
+
+#define GT_SDRAM_B0_SIZE_SHF		11
+#define GT_SDRAM_B0_SIZE_MSK		(MSK(1) << GT_SDRAM_B0_SIZE_SHF)
+#define GT_SDRAM_B0_SIZE_BIT		GT_SDRAM_B0_SIZE_MSK
+#define GT_SDRAM_B0_SIZE_16M		0
+#define GT_SDRAM_B0_SIZE_64M		1
+
+#define GT_SDRAM_B0_EXTPAR_SHF		12
+#define GT_SDRAM_B0_EXTPAR_MSK		(MSK(1) << GT_SDRAM_B0_EXTPAR_SHF)
+#define GT_SDRAM_B0_EXTPAR_BIT		GT_SDRAM_B0_EXTPAR_MSK
+
+#define GT_SDRAM_B0_BLEN_SHF		13
+#define GT_SDRAM_B0_BLEN_MSK		(MSK(1) << GT_SDRAM_B0_BLEN_SHF)
+#define GT_SDRAM_B0_BLEN_BIT		GT_SDRAM_B0_BLEN_MSK
+#define GT_SDRAM_B0_BLEN_8		0
+#define GT_SDRAM_B0_BLEN_4		1
+
+
+#define GT_SDRAM_CFG_REFINT_SHF		0
+#define GT_SDRAM_CFG_REFINT_MSK		(MSK(14) << GT_SDRAM_CFG_REFINT_SHF)
+
+#define GT_SDRAM_CFG_NINTERLEAVE_SHF	14
+#define GT_SDRAM_CFG_NINTERLEAVE_MSK	(MSK(1) << GT_SDRAM_CFG_NINTERLEAVE_SHF)
+#define GT_SDRAM_CFG_NINTERLEAVE_BIT	GT_SDRAM_CFG_NINTERLEAVE_MSK
+
+#define GT_SDRAM_CFG_RMW_SHF		15
+#define GT_SDRAM_CFG_RMW_MSK		(MSK(1) << GT_SDRAM_CFG_RMW_SHF)
+#define GT_SDRAM_CFG_RMW_BIT		GT_SDRAM_CFG_RMW_MSK
+
+#define GT_SDRAM_CFG_NONSTAGREF_SHF	16
+#define GT_SDRAM_CFG_NONSTAGREF_MSK	(MSK(1) << GT_SDRAM_CFG_NONSTAGREF_SHF)
+#define GT_SDRAM_CFG_NONSTAGREF_BIT	GT_SDRAM_CFG_NONSTAGREF_MSK
+
+#define GT_SDRAM_CFG_DUPCNTL_SHF	19
+#define GT_SDRAM_CFG_DUPCNTL_MSK	(MSK(1) << GT_SDRAM_CFG_DUPCNTL_SHF)
+#define GT_SDRAM_CFG_DUPCNTL_BIT	GT_SDRAM_CFG_DUPCNTL_MSK
+
+#define GT_SDRAM_CFG_DUPBA_SHF		20
+#define GT_SDRAM_CFG_DUPBA_MSK		(MSK(1) << GT_SDRAM_CFG_DUPBA_SHF)
+#define GT_SDRAM_CFG_DUPBA_BIT		GT_SDRAM_CFG_DUPBA_MSK
+
+#define GT_SDRAM_CFG_DUPEOT0_SHF	21
+#define GT_SDRAM_CFG_DUPEOT0_MSK	(MSK(1) << GT_SDRAM_CFG_DUPEOT0_SHF)
+#define GT_SDRAM_CFG_DUPEOT0_BIT	GT_SDRAM_CFG_DUPEOT0_MSK
+
+#define GT_SDRAM_CFG_DUPEOT1_SHF	22
+#define GT_SDRAM_CFG_DUPEOT1_MSK	(MSK(1) << GT_SDRAM_CFG_DUPEOT1_SHF)
+#define GT_SDRAM_CFG_DUPEOT1_BIT	GT_SDRAM_CFG_DUPEOT1_MSK
+
+#define GT_SDRAM_OPMODE_OP_SHF		0
+#define GT_SDRAM_OPMODE_OP_MSK		(MSK(3) << GT_SDRAM_OPMODE_OP_SHF)
+#define GT_SDRAM_OPMODE_OP_NORMAL	0
+#define GT_SDRAM_OPMODE_OP_NOP		1
+#define GT_SDRAM_OPMODE_OP_PRCHG	2
+#define GT_SDRAM_OPMODE_OP_MODE		3
+#define GT_SDRAM_OPMODE_OP_CBR		4
+
+#define GT_TC_CONTROL_ENTC0_SHF		0
+#define GT_TC_CONTROL_ENTC0_MSK		(MSK(1) << GT_TC_CONTROL_ENTC0_SHF)
+#define GT_TC_CONTROL_ENTC0_BIT		GT_TC_CONTROL_ENTC0_MSK
+#define GT_TC_CONTROL_SELTC0_SHF	1
+#define GT_TC_CONTROL_SELTC0_MSK	(MSK(1) << GT_TC_CONTROL_SELTC0_SHF)
+#define GT_TC_CONTROL_SELTC0_BIT	GT_TC_CONTROL_SELTC0_MSK
+
+
+#define GT_PCI0_BARE_SWSCS3BOOTDIS_SHF	0
+#define GT_PCI0_BARE_SWSCS3BOOTDIS_MSK	(MSK(1) << GT_PCI0_BARE_SWSCS3BOOTDIS_SHF)
+#define GT_PCI0_BARE_SWSCS3BOOTDIS_BIT	GT_PCI0_BARE_SWSCS3BOOTDIS_MSK
+
+#define GT_PCI0_BARE_SWSCS32DIS_SHF	1
+#define GT_PCI0_BARE_SWSCS32DIS_MSK	(MSK(1) << GT_PCI0_BARE_SWSCS32DIS_SHF)
+#define GT_PCI0_BARE_SWSCS32DIS_BIT	GT_PCI0_BARE_SWSCS32DIS_MSK
+
+#define GT_PCI0_BARE_SWSCS10DIS_SHF	2
+#define GT_PCI0_BARE_SWSCS10DIS_MSK	(MSK(1) << GT_PCI0_BARE_SWSCS10DIS_SHF)
+#define GT_PCI0_BARE_SWSCS10DIS_BIT	GT_PCI0_BARE_SWSCS10DIS_MSK
+
+#define GT_PCI0_BARE_INTIODIS_SHF	3
+#define GT_PCI0_BARE_INTIODIS_MSK	(MSK(1) << GT_PCI0_BARE_INTIODIS_SHF)
+#define GT_PCI0_BARE_INTIODIS_BIT	GT_PCI0_BARE_INTIODIS_MSK
+
+#define GT_PCI0_BARE_INTMEMDIS_SHF	4
+#define GT_PCI0_BARE_INTMEMDIS_MSK	(MSK(1) << GT_PCI0_BARE_INTMEMDIS_SHF)
+#define GT_PCI0_BARE_INTMEMDIS_BIT	GT_PCI0_BARE_INTMEMDIS_MSK
+
+#define GT_PCI0_BARE_CS3BOOTDIS_SHF	5
+#define GT_PCI0_BARE_CS3BOOTDIS_MSK	(MSK(1) << GT_PCI0_BARE_CS3BOOTDIS_SHF)
+#define GT_PCI0_BARE_CS3BOOTDIS_BIT	GT_PCI0_BARE_CS3BOOTDIS_MSK
+
+#define GT_PCI0_BARE_CS20DIS_SHF	6
+#define GT_PCI0_BARE_CS20DIS_MSK	(MSK(1) << GT_PCI0_BARE_CS20DIS_SHF)
+#define GT_PCI0_BARE_CS20DIS_BIT	GT_PCI0_BARE_CS20DIS_MSK
+
+#define GT_PCI0_BARE_SCS32DIS_SHF	7
+#define GT_PCI0_BARE_SCS32DIS_MSK	(MSK(1) << GT_PCI0_BARE_SCS32DIS_SHF)
+#define GT_PCI0_BARE_SCS32DIS_BIT	GT_PCI0_BARE_SCS32DIS_MSK
+
+#define GT_PCI0_BARE_SCS10DIS_SHF	8
+#define GT_PCI0_BARE_SCS10DIS_MSK	(MSK(1) << GT_PCI0_BARE_SCS10DIS_SHF)
+#define GT_PCI0_BARE_SCS10DIS_BIT	GT_PCI0_BARE_SCS10DIS_MSK
+
+
+#define GT_INTRCAUSE_MASABORT0_SHF	18
+#define GT_INTRCAUSE_MASABORT0_MSK	(MSK(1) << GT_INTRCAUSE_MASABORT0_SHF)
+#define GT_INTRCAUSE_MASABORT0_BIT	GT_INTRCAUSE_MASABORT0_MSK
+
+#define GT_INTRCAUSE_TARABORT0_SHF	19
+#define GT_INTRCAUSE_TARABORT0_MSK	(MSK(1) << GT_INTRCAUSE_TARABORT0_SHF)
+#define GT_INTRCAUSE_TARABORT0_BIT	GT_INTRCAUSE_TARABORT0_MSK
+
+
+#define GT_PCI0_CFGADDR_REGNUM_SHF	2
+#define GT_PCI0_CFGADDR_REGNUM_MSK	(MSK(6) << GT_PCI0_CFGADDR_REGNUM_SHF)
+#define GT_PCI0_CFGADDR_FUNCTNUM_SHF	8
+#define GT_PCI0_CFGADDR_FUNCTNUM_MSK	(MSK(3) << GT_PCI0_CFGADDR_FUNCTNUM_SHF)
+#define GT_PCI0_CFGADDR_DEVNUM_SHF	11
+#define GT_PCI0_CFGADDR_DEVNUM_MSK	(MSK(5) << GT_PCI0_CFGADDR_DEVNUM_SHF)
+#define GT_PCI0_CFGADDR_BUSNUM_SHF	16
+#define GT_PCI0_CFGADDR_BUSNUM_MSK	(MSK(8) << GT_PCI0_CFGADDR_BUSNUM_SHF)
+#define GT_PCI0_CFGADDR_CONFIGEN_SHF	31
+#define GT_PCI0_CFGADDR_CONFIGEN_MSK	(MSK(1) << GT_PCI0_CFGADDR_CONFIGEN_SHF)
+#define GT_PCI0_CFGADDR_CONFIGEN_BIT	GT_PCI0_CFGADDR_CONFIGEN_MSK
+
+#define GT_PCI0_CMD_MBYTESWAP_SHF	0
+#define GT_PCI0_CMD_MBYTESWAP_MSK	(MSK(1) << GT_PCI0_CMD_MBYTESWAP_SHF)
+#define GT_PCI0_CMD_MBYTESWAP_BIT	GT_PCI0_CMD_MBYTESWAP_MSK
+#define GT_PCI0_CMD_MWORDSWAP_SHF	10
+#define GT_PCI0_CMD_MWORDSWAP_MSK	(MSK(1) << GT_PCI0_CMD_MWORDSWAP_SHF)
+#define GT_PCI0_CMD_MWORDSWAP_BIT	GT_PCI0_CMD_MWORDSWAP_MSK
+#define GT_PCI0_CMD_SBYTESWAP_SHF	16
+#define GT_PCI0_CMD_SBYTESWAP_MSK	(MSK(1) << GT_PCI0_CMD_SBYTESWAP_SHF)
+#define GT_PCI0_CMD_SBYTESWAP_BIT	GT_PCI0_CMD_SBYTESWAP_MSK
+#define GT_PCI0_CMD_SWORDSWAP_SHF	11
+#define GT_PCI0_CMD_SWORDSWAP_MSK	(MSK(1) << GT_PCI0_CMD_SWORDSWAP_SHF)
+#define GT_PCI0_CMD_SWORDSWAP_BIT	GT_PCI0_CMD_SWORDSWAP_MSK
+
+#define GT_INTR_T0EXP_SHF		8
+#define GT_INTR_T0EXP_MSK		(MSK(1) << GT_INTR_T0EXP_SHF)
+#define GT_INTR_T0EXP_BIT		GT_INTR_T0EXP_MSK
+#define GT_INTR_RETRYCTR0_SHF		20
+#define GT_INTR_RETRYCTR0_MSK		(MSK(1) << GT_INTR_RETRYCTR0_SHF)
+#define GT_INTR_RETRYCTR0_BIT		GT_INTR_RETRYCTR0_MSK
+
+/*
+ *  Misc
+ */
+#define GT_DEF_PCI0_IO_BASE	0x10000000UL
+#define GT_DEF_PCI0_IO_SIZE	0x02000000UL
+#define GT_DEF_PCI0_MEM0_BASE	0x12000000UL
+#define GT_DEF_PCI0_MEM0_SIZE	0x02000000UL
+#define GT_DEF_BASE		0x14000000UL
+
+#define GT_MAX_BANKSIZE		(256 * 1024 * 1024)	/* Max 256MB bank  */
+#define GT_LATTIM_MIN		6			/* Minimum lat	*/
+
+/*
+ * The gt64120_dep.h file must define the following macros
+ *
+ *   GT_READ(ofs, data_pointer)
+ *   GT_WRITE(ofs, data)	   - read/write GT64120 registers in 32bit
+ *
+ *   TIMER	- gt64120 timer irq, temporary solution until
+ *		  full gt64120 cascade interrupt support is in place
+ */
+
+#include <mach-gt64120.h>
+
+/*
+ * Because of an error/peculiarity in the Galileo chip, we need to swap the
+ * bytes when running bigendian.  We also provide non-swapping versions.
+ */
+#define __GT_READ(ofs)							\
+	(*(volatile u32 *)(GT64120_BASE+(ofs)))
+#define __GT_WRITE(ofs, data)						\
+	do { *(volatile u32 *)(GT64120_BASE+(ofs)) = (data); } while (0)
+#define GT_READ(ofs)		le32_to_cpu(__GT_READ(ofs))
+#define GT_WRITE(ofs, data)	__GT_WRITE(ofs, cpu_to_le32(data))
+
+extern void gt641xx_set_base_clock(unsigned int clock);
+extern int gt641xx_timer0_state(void);
+
+#endif /* _ASM_GT64120_H */
diff --git a/arch/mips/include/asm/hardirq.h b/arch/mips/include/asm/hardirq.h
new file mode 100644
index 000000000..c977a86c2
--- /dev/null
+++ b/arch/mips/include/asm/hardirq.h
@@ -0,0 +1,18 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1997, 98, 99, 2000, 01, 05 Ralf Baechle (ralf@linux-mips.org)
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ * Copyright (C) 2001 MIPS Technologies, Inc.
+ */
+#ifndef _ASM_HARDIRQ_H
+#define _ASM_HARDIRQ_H
+
+extern void ack_bad_irq(unsigned int irq);
+#define ack_bad_irq ack_bad_irq
+
+#include <asm-generic/hardirq.h>
+
+#endif /* _ASM_HARDIRQ_H */
diff --git a/arch/mips/include/asm/hazards.h b/arch/mips/include/asm/hazards.h
new file mode 100644
index 000000000..cb16be93b
--- /dev/null
+++ b/arch/mips/include/asm/hazards.h
@@ -0,0 +1,422 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003, 04, 07 Ralf Baechle <ralf@linux-mips.org>
+ * Copyright (C) MIPS Technologies, Inc.
+ *   written by Ralf Baechle <ralf@linux-mips.org>
+ */
+#ifndef _ASM_HAZARDS_H
+#define _ASM_HAZARDS_H
+
+#include <linux/stringify.h>
+#include <asm/compiler.h>
+
+#define ___ssnop							\
+	sll	$0, $0, 1
+
+#define ___ehb								\
+	sll	$0, $0, 3
+
+/*
+ * TLB hazards
+ */
+#if (defined(CONFIG_CPU_MIPSR2) || defined(CONFIG_CPU_MIPSR5) || \
+     defined(CONFIG_CPU_MIPSR6)) && \
+    !defined(CONFIG_CPU_CAVIUM_OCTEON) && !defined(CONFIG_CPU_LOONGSON64)
+
+/*
+ * MIPSR2 defines ehb for hazard avoidance
+ */
+
+#define __mtc0_tlbw_hazard						\
+	___ehb
+
+#define __mtc0_tlbr_hazard						\
+	___ehb
+
+#define __tlbw_use_hazard						\
+	___ehb
+
+#define __tlb_read_hazard						\
+	___ehb
+
+#define __tlb_probe_hazard						\
+	___ehb
+
+#define __irq_enable_hazard						\
+	___ehb
+
+#define __irq_disable_hazard						\
+	___ehb
+
+#define __back_to_back_c0_hazard					\
+	___ehb
+
+/*
+ * gcc has a tradition of misscompiling the previous construct using the
+ * address of a label as argument to inline assembler.	Gas otoh has the
+ * annoying difference between la and dla which are only usable for 32-bit
+ * rsp. 64-bit code, so can't be used without conditional compilation.
+ * The alternative is switching the assembler to 64-bit code which happens
+ * to work right even for 32-bit code...
+ */
+#define instruction_hazard()						\
+do {									\
+	unsigned long tmp;						\
+									\
+	__asm__ __volatile__(						\
+	"	.set	push					\n"	\
+	"	.set "MIPS_ISA_LEVEL"				\n"	\
+	"	dla	%0, 1f					\n"	\
+	"	jr.hb	%0					\n"	\
+	"	.set	pop					\n"	\
+	"1:							\n"	\
+	: "=r" (tmp));							\
+} while (0)
+
+#elif (defined(CONFIG_CPU_MIPSR1) && !defined(CONFIG_MIPS_ALCHEMY)) || \
+	defined(CONFIG_CPU_BMIPS)
+
+/*
+ * These are slightly complicated by the fact that we guarantee R1 kernels to
+ * run fine on R2 processors.
+ */
+
+#define __mtc0_tlbw_hazard						\
+	___ssnop;							\
+	___ssnop;							\
+	___ehb
+
+#define __mtc0_tlbr_hazard						\
+	___ssnop;							\
+	___ssnop;							\
+	___ehb
+
+#define __tlbw_use_hazard						\
+	___ssnop;							\
+	___ssnop;							\
+	___ssnop;							\
+	___ehb
+
+#define __tlb_read_hazard						\
+	___ssnop;							\
+	___ssnop;							\
+	___ssnop;							\
+	___ehb
+
+#define __tlb_probe_hazard						\
+	___ssnop;							\
+	___ssnop;							\
+	___ssnop;							\
+	___ehb
+
+#define __irq_enable_hazard						\
+	___ssnop;							\
+	___ssnop;							\
+	___ssnop;							\
+	___ehb
+
+#define __irq_disable_hazard						\
+	___ssnop;							\
+	___ssnop;							\
+	___ssnop;							\
+	___ehb
+
+#define __back_to_back_c0_hazard					\
+	___ssnop;							\
+	___ssnop;							\
+	___ssnop;							\
+	___ehb
+
+/*
+ * gcc has a tradition of misscompiling the previous construct using the
+ * address of a label as argument to inline assembler.	Gas otoh has the
+ * annoying difference between la and dla which are only usable for 32-bit
+ * rsp. 64-bit code, so can't be used without conditional compilation.
+ * The alternative is switching the assembler to 64-bit code which happens
+ * to work right even for 32-bit code...
+ */
+#define __instruction_hazard()						\
+do {									\
+	unsigned long tmp;						\
+									\
+	__asm__ __volatile__(						\
+	"	.set	push					\n"	\
+	"	.set	mips64r2				\n"	\
+	"	dla	%0, 1f					\n"	\
+	"	jr.hb	%0					\n"	\
+	"	.set	pop					\n"	\
+	"1:							\n"	\
+	: "=r" (tmp));							\
+} while (0)
+
+#define instruction_hazard()						\
+do {									\
+	if (cpu_has_mips_r2_r6)						\
+		__instruction_hazard();					\
+} while (0)
+
+#elif defined(CONFIG_MIPS_ALCHEMY) || defined(CONFIG_CPU_CAVIUM_OCTEON) || \
+	defined(CONFIG_CPU_LOONGSON2EF) || defined(CONFIG_CPU_LOONGSON64) || \
+	defined(CONFIG_CPU_R10000) || defined(CONFIG_CPU_R5500)
+
+/*
+ * R10000 rocks - all hazards handled in hardware, so this becomes a nobrainer.
+ */
+
+#define __mtc0_tlbw_hazard
+
+#define __mtc0_tlbr_hazard
+
+#define __tlbw_use_hazard
+
+#define __tlb_read_hazard
+
+#define __tlb_probe_hazard
+
+#define __irq_enable_hazard
+
+#define __irq_disable_hazard
+
+#define __back_to_back_c0_hazard
+
+#define instruction_hazard() do { } while (0)
+
+#elif defined(CONFIG_CPU_SB1)
+
+/*
+ * Mostly like R4000 for historic reasons
+ */
+#define __mtc0_tlbw_hazard
+
+#define __mtc0_tlbr_hazard
+
+#define __tlbw_use_hazard
+
+#define __tlb_read_hazard
+
+#define __tlb_probe_hazard
+
+#define __irq_enable_hazard
+
+#define __irq_disable_hazard						\
+	___ssnop;							\
+	___ssnop;							\
+	___ssnop
+
+#define __back_to_back_c0_hazard
+
+#define instruction_hazard() do { } while (0)
+
+#else
+
+/*
+ * Finally the catchall case for all other processors including R4000, R4400,
+ * R4600, R4700, R5000, RM7000, NEC VR41xx etc.
+ *
+ * The taken branch will result in a two cycle penalty for the two killed
+ * instructions on R4000 / R4400.  Other processors only have a single cycle
+ * hazard so this is nice trick to have an optimal code for a range of
+ * processors.
+ */
+#define __mtc0_tlbw_hazard						\
+	nop;								\
+	nop
+
+#define __mtc0_tlbr_hazard						\
+	nop;								\
+	nop
+
+#define __tlbw_use_hazard						\
+	nop;								\
+	nop;								\
+	nop
+
+#define __tlb_read_hazard						\
+	nop;								\
+	nop;								\
+	nop
+
+#define __tlb_probe_hazard						\
+	nop;								\
+	nop;								\
+	nop
+
+#define __irq_enable_hazard						\
+	___ssnop;							\
+	___ssnop;							\
+	___ssnop
+
+#define __irq_disable_hazard						\
+	nop;								\
+	nop;								\
+	nop
+
+#define __back_to_back_c0_hazard					\
+	___ssnop;							\
+	___ssnop;							\
+	___ssnop
+
+#define instruction_hazard() do { } while (0)
+
+#endif
+
+
+/* FPU hazards */
+
+#if defined(CONFIG_CPU_SB1)
+
+#define __enable_fpu_hazard						\
+	.set	push;							\
+	.set	mips64;							\
+	.set	noreorder;						\
+	___ssnop;							\
+	bnezl	$0, .+4;						\
+	___ssnop;							\
+	.set	pop
+
+#define __disable_fpu_hazard
+
+#elif defined(CONFIG_CPU_MIPSR2) || defined(CONFIG_CPU_MIPSR5) || \
+      defined(CONFIG_CPU_MIPSR6)
+
+#define __enable_fpu_hazard						\
+	___ehb
+
+#define __disable_fpu_hazard						\
+	___ehb
+
+#else
+
+#define __enable_fpu_hazard						\
+	nop;								\
+	nop;								\
+	nop;								\
+	nop
+
+#define __disable_fpu_hazard						\
+	___ehb
+
+#endif
+
+#ifdef __ASSEMBLY__
+
+#define _ssnop ___ssnop
+#define	_ehb ___ehb
+#define mtc0_tlbw_hazard __mtc0_tlbw_hazard
+#define mtc0_tlbr_hazard __mtc0_tlbr_hazard
+#define tlbw_use_hazard __tlbw_use_hazard
+#define tlb_read_hazard __tlb_read_hazard
+#define tlb_probe_hazard __tlb_probe_hazard
+#define irq_enable_hazard __irq_enable_hazard
+#define irq_disable_hazard __irq_disable_hazard
+#define back_to_back_c0_hazard __back_to_back_c0_hazard
+#define enable_fpu_hazard __enable_fpu_hazard
+#define disable_fpu_hazard __disable_fpu_hazard
+
+#else
+
+#define _ssnop()							\
+do {									\
+	__asm__ __volatile__(						\
+	__stringify(___ssnop)						\
+	);								\
+} while (0)
+
+#define	_ehb()								\
+do {									\
+	__asm__ __volatile__(						\
+	__stringify(___ehb)						\
+	);								\
+} while (0)
+
+
+#define mtc0_tlbw_hazard()						\
+do {									\
+	__asm__ __volatile__(						\
+	__stringify(__mtc0_tlbw_hazard)					\
+	);								\
+} while (0)
+
+
+#define mtc0_tlbr_hazard()						\
+do {									\
+	__asm__ __volatile__(						\
+	__stringify(__mtc0_tlbr_hazard)					\
+	);								\
+} while (0)
+
+
+#define tlbw_use_hazard()						\
+do {									\
+	__asm__ __volatile__(						\
+	__stringify(__tlbw_use_hazard)					\
+	);								\
+} while (0)
+
+
+#define tlb_read_hazard()						\
+do {									\
+	__asm__ __volatile__(						\
+	__stringify(__tlb_read_hazard)					\
+	);								\
+} while (0)
+
+
+#define tlb_probe_hazard()						\
+do {									\
+	__asm__ __volatile__(						\
+	__stringify(__tlb_probe_hazard)					\
+	);								\
+} while (0)
+
+
+#define irq_enable_hazard()						\
+do {									\
+	__asm__ __volatile__(						\
+	__stringify(__irq_enable_hazard)				\
+	);								\
+} while (0)
+
+
+#define irq_disable_hazard()						\
+do {									\
+	__asm__ __volatile__(						\
+	__stringify(__irq_disable_hazard)				\
+	);								\
+} while (0)
+
+
+#define back_to_back_c0_hazard() 					\
+do {									\
+	__asm__ __volatile__(						\
+	__stringify(__back_to_back_c0_hazard)				\
+	);								\
+} while (0)
+
+
+#define enable_fpu_hazard()						\
+do {									\
+	__asm__ __volatile__(						\
+	__stringify(__enable_fpu_hazard)				\
+	);								\
+} while (0)
+
+
+#define disable_fpu_hazard()						\
+do {									\
+	__asm__ __volatile__(						\
+	__stringify(__disable_fpu_hazard)				\
+	);								\
+} while (0)
+
+/*
+ * MIPS R2 instruction hazard barrier.   Needs to be called as a subroutine.
+ */
+extern void mips_ihb(void);
+
+#endif /* __ASSEMBLY__  */
+
+#endif /* _ASM_HAZARDS_H */
diff --git a/arch/mips/include/asm/highmem.h b/arch/mips/include/asm/highmem.h
new file mode 100644
index 000000000..92a380210
--- /dev/null
+++ b/arch/mips/include/asm/highmem.h
@@ -0,0 +1,60 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * highmem.h: virtual kernel memory mappings for high memory
+ *
+ * Used in CONFIG_HIGHMEM systems for memory pages which
+ * are not addressable by direct kernel virtual addresses.
+ *
+ * Copyright (C) 1999 Gerhard Wichert, Siemens AG
+ *		      Gerhard.Wichert@pdb.siemens.de
+ *
+ *
+ * Redesigned the x86 32-bit VM architecture to deal with
+ * up to 16 Terabyte physical memory. With current x86 CPUs
+ * we now support up to 64 Gigabytes physical RAM.
+ *
+ * Copyright (C) 1999 Ingo Molnar <mingo@redhat.com>
+ */
+#ifndef _ASM_HIGHMEM_H
+#define _ASM_HIGHMEM_H
+
+#ifdef __KERNEL__
+
+#include <linux/bug.h>
+#include <linux/interrupt.h>
+#include <linux/uaccess.h>
+#include <asm/cpu-features.h>
+#include <asm/kmap_size.h>
+
+/* declarations for highmem.c */
+extern unsigned long highstart_pfn, highend_pfn;
+
+extern pte_t *pkmap_page_table;
+
+/*
+ * Right now we initialize only a single pte table. It can be extended
+ * easily, subsequent pte tables have to be allocated in one physical
+ * chunk of RAM.
+ */
+#if defined(CONFIG_PHYS_ADDR_T_64BIT) || defined(CONFIG_MIPS_HUGE_TLB_SUPPORT)
+#define LAST_PKMAP 512
+#else
+#define LAST_PKMAP 1024
+#endif
+
+#define LAST_PKMAP_MASK (LAST_PKMAP-1)
+#define PKMAP_NR(virt)	((virt-PKMAP_BASE) >> PAGE_SHIFT)
+#define PKMAP_ADDR(nr)	(PKMAP_BASE + ((nr) << PAGE_SHIFT))
+
+#define ARCH_HAS_KMAP_FLUSH_TLB
+extern void kmap_flush_tlb(unsigned long addr);
+
+#define flush_cache_kmaps()	BUG_ON(cpu_has_dc_aliases)
+
+#define arch_kmap_local_set_pte(mm, vaddr, ptep, ptev)	set_pte(ptep, ptev)
+#define arch_kmap_local_post_map(vaddr, pteval)	local_flush_tlb_one(vaddr)
+#define arch_kmap_local_post_unmap(vaddr)	local_flush_tlb_one(vaddr)
+
+#endif /* __KERNEL__ */
+
+#endif /* _ASM_HIGHMEM_H */
diff --git a/arch/mips/include/asm/hpet.h b/arch/mips/include/asm/hpet.h
new file mode 100644
index 000000000..d47268ece
--- /dev/null
+++ b/arch/mips/include/asm/hpet.h
@@ -0,0 +1,74 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _ASM_HPET_H
+#define _ASM_HPET_H
+
+#ifdef CONFIG_RS780_HPET
+
+#define HPET_MMAP_SIZE		1024
+
+#define HPET_ID			0x000
+#define HPET_PERIOD		0x004
+#define HPET_CFG		0x010
+#define HPET_STATUS		0x020
+#define HPET_COUNTER	0x0f0
+
+#define HPET_Tn_CFG(n)		(0x100 + 0x20 * n)
+#define HPET_Tn_CMP(n)		(0x108 + 0x20 * n)
+#define HPET_Tn_ROUTE(n)	(0x110 + 0x20 * n)
+
+#define HPET_T0_IRS		0x001
+#define HPET_T1_IRS		0x002
+#define HPET_T3_IRS		0x004
+
+#define HPET_T0_CFG		0x100
+#define HPET_T0_CMP		0x108
+#define HPET_T0_ROUTE	0x110
+#define HPET_T1_CFG		0x120
+#define HPET_T1_CMP		0x128
+#define HPET_T1_ROUTE	0x130
+#define HPET_T2_CFG		0x140
+#define HPET_T2_CMP		0x148
+#define HPET_T2_ROUTE	0x150
+
+#define HPET_ID_REV			0x000000ff
+#define HPET_ID_NUMBER		0x00001f00
+#define HPET_ID_64BIT		0x00002000
+#define HPET_ID_LEGSUP		0x00008000
+#define HPET_ID_VENDOR		0xffff0000
+#define HPET_ID_NUMBER_SHIFT	8
+#define HPET_ID_VENDOR_SHIFT	16
+
+#define HPET_CFG_ENABLE		0x001
+#define HPET_CFG_LEGACY		0x002
+#define HPET_LEGACY_8254		2
+#define HPET_LEGACY_RTC		8
+
+#define HPET_TN_LEVEL		0x0002
+#define HPET_TN_ENABLE		0x0004
+#define HPET_TN_PERIODIC	0x0008
+#define HPET_TN_PERIODIC_CAP	0x0010
+#define HPET_TN_64BIT_CAP	0x0020
+#define HPET_TN_SETVAL		0x0040
+#define HPET_TN_32BIT		0x0100
+#define HPET_TN_ROUTE		0x3e00
+#define HPET_TN_FSB			0x4000
+#define HPET_TN_FSB_CAP		0x8000
+#define HPET_TN_ROUTE_SHIFT	9
+
+/* Max HPET Period is 10^8 femto sec as in HPET spec */
+#define HPET_MAX_PERIOD		100000000UL
+/*
+ * Min HPET period is 10^5 femto sec just for safety. If it is less than this,
+ * then 32 bit HPET counter wrapsaround in less than 0.5 sec.
+ */
+#define HPET_MIN_PERIOD		100000UL
+
+#define HPET_ADDR		0x20000
+#define HPET_MMIO_ADDR	0x90000e0000020000
+#define HPET_FREQ		14318780
+#define HPET_COMPARE_VAL	((HPET_FREQ + HZ / 2) / HZ)
+#define HPET_T0_IRQ		0
+
+extern void __init setup_hpet_timer(void);
+#endif /* CONFIG_RS780_HPET */
+#endif /* _ASM_HPET_H */
diff --git a/arch/mips/include/asm/hugetlb.h b/arch/mips/include/asm/hugetlb.h
new file mode 100644
index 000000000..fd69c8808
--- /dev/null
+++ b/arch/mips/include/asm/hugetlb.h
@@ -0,0 +1,89 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008, 2009 Cavium Networks, Inc.
+ */
+
+#ifndef __ASM_HUGETLB_H
+#define __ASM_HUGETLB_H
+
+#include <asm/page.h>
+
+#define __HAVE_ARCH_PREPARE_HUGEPAGE_RANGE
+static inline int prepare_hugepage_range(struct file *file,
+					 unsigned long addr,
+					 unsigned long len)
+{
+	unsigned long task_size = STACK_TOP;
+	struct hstate *h = hstate_file(file);
+
+	if (len & ~huge_page_mask(h))
+		return -EINVAL;
+	if (addr & ~huge_page_mask(h))
+		return -EINVAL;
+	if (len > task_size)
+		return -ENOMEM;
+	if (task_size - len < addr)
+		return -EINVAL;
+	return 0;
+}
+
+#define __HAVE_ARCH_HUGE_PTEP_GET_AND_CLEAR
+static inline pte_t huge_ptep_get_and_clear(struct mm_struct *mm,
+					    unsigned long addr, pte_t *ptep)
+{
+	pte_t clear;
+	pte_t pte = *ptep;
+
+	pte_val(clear) = (unsigned long)invalid_pte_table;
+	set_pte_at(mm, addr, ptep, clear);
+	return pte;
+}
+
+#define __HAVE_ARCH_HUGE_PTEP_CLEAR_FLUSH
+static inline pte_t huge_ptep_clear_flush(struct vm_area_struct *vma,
+					  unsigned long addr, pte_t *ptep)
+{
+	pte_t pte;
+
+	/*
+	 * clear the huge pte entry firstly, so that the other smp threads will
+	 * not get old pte entry after finishing flush_tlb_page and before
+	 * setting new huge pte entry
+	 */
+	pte = huge_ptep_get_and_clear(vma->vm_mm, addr, ptep);
+	flush_tlb_page(vma, addr);
+	return pte;
+}
+
+#define __HAVE_ARCH_HUGE_PTE_NONE
+static inline int huge_pte_none(pte_t pte)
+{
+	unsigned long val = pte_val(pte) & ~_PAGE_GLOBAL;
+	return !val || (val == (unsigned long)invalid_pte_table);
+}
+
+#define __HAVE_ARCH_HUGE_PTEP_SET_ACCESS_FLAGS
+static inline int huge_ptep_set_access_flags(struct vm_area_struct *vma,
+					     unsigned long addr,
+					     pte_t *ptep, pte_t pte,
+					     int dirty)
+{
+	int changed = !pte_same(*ptep, pte);
+
+	if (changed) {
+		set_pte_at(vma->vm_mm, addr, ptep, pte);
+		/*
+		 * There could be some standard sized pages in there,
+		 * get them all.
+		 */
+		flush_tlb_range(vma, addr, addr + HPAGE_SIZE);
+	}
+	return changed;
+}
+
+#include <asm-generic/hugetlb.h>
+
+#endif /* __ASM_HUGETLB_H */
diff --git a/arch/mips/include/asm/hw_irq.h b/arch/mips/include/asm/hw_irq.h
new file mode 100644
index 000000000..9e8ef5994
--- /dev/null
+++ b/arch/mips/include/asm/hw_irq.h
@@ -0,0 +1,20 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2000, 2001, 2002 by Ralf Baechle
+ */
+#ifndef __ASM_HW_IRQ_H
+#define __ASM_HW_IRQ_H
+
+#include <linux/atomic.h>
+
+extern atomic_t irq_err_count;
+
+/*
+ * interrupt-retrigger: NOP for now. This may not be appropriate for all
+ * machines, we'll see ...
+ */
+
+#endif /* __ASM_HW_IRQ_H */
diff --git a/arch/mips/include/asm/i8259.h b/arch/mips/include/asm/i8259.h
new file mode 100644
index 000000000..a54b9649d
--- /dev/null
+++ b/arch/mips/include/asm/i8259.h
@@ -0,0 +1,93 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ *	include/asm-mips/i8259.h
+ *
+ *	i8259A interrupt definitions.
+ *
+ *	Copyright (C) 2003  Maciej W. Rozycki
+ *	Copyright (C) 2003  Ralf Baechle <ralf@linux-mips.org>
+ */
+#ifndef _ASM_I8259_H
+#define _ASM_I8259_H
+
+#include <linux/compiler.h>
+#include <linux/spinlock.h>
+
+#include <asm/io.h>
+#include <irq.h>
+
+/* i8259A PIC registers */
+#define PIC_MASTER_CMD		0x20
+#define PIC_MASTER_IMR		0x21
+#define PIC_MASTER_ISR		PIC_MASTER_CMD
+#define PIC_MASTER_POLL		PIC_MASTER_ISR
+#define PIC_MASTER_OCW3		PIC_MASTER_ISR
+#define PIC_SLAVE_CMD		0xa0
+#define PIC_SLAVE_IMR		0xa1
+
+/* i8259A PIC related value */
+#define PIC_CASCADE_IR		2
+#define MASTER_ICW4_DEFAULT	0x01
+#define SLAVE_ICW4_DEFAULT	0x01
+#define PIC_ICW4_AEOI		2
+
+extern raw_spinlock_t i8259A_lock;
+
+extern void make_8259A_irq(unsigned int irq);
+
+extern void init_i8259_irqs(void);
+extern struct irq_domain *__init_i8259_irqs(struct device_node *node);
+
+/**
+ * i8159_set_poll() - Override the i8259 polling function
+ * @poll: pointer to platform-specific polling function
+ *
+ * Call this to override the generic i8259 polling function, which directly
+ * accesses i8259 registers, with a platform specific one which may be faster
+ * in cases where hardware provides a more optimal means of polling for an
+ * interrupt.
+ */
+extern void i8259_set_poll(int (*poll)(void));
+
+/*
+ * Do the traditional i8259 interrupt polling thing.  This is for the few
+ * cases where no better interrupt acknowledge method is available and we
+ * absolutely must touch the i8259.
+ */
+static inline int i8259_irq(void)
+{
+	int irq;
+
+	raw_spin_lock(&i8259A_lock);
+
+	/* Perform an interrupt acknowledge cycle on controller 1. */
+	outb(0x0C, PIC_MASTER_CMD);		/* prepare for poll */
+	irq = inb(PIC_MASTER_CMD) & 7;
+	if (irq == PIC_CASCADE_IR) {
+		/*
+		 * Interrupt is cascaded so perform interrupt
+		 * acknowledge on controller 2.
+		 */
+		outb(0x0C, PIC_SLAVE_CMD);		/* prepare for poll */
+		irq = (inb(PIC_SLAVE_CMD) & 7) + 8;
+	}
+
+	if (unlikely(irq == 7)) {
+		/*
+		 * This may be a spurious interrupt.
+		 *
+		 * Read the interrupt status register (ISR). If the most
+		 * significant bit is not set then there is no valid
+		 * interrupt.
+		 */
+		outb(0x0B, PIC_MASTER_ISR);		/* ISR register */
+		if(~inb(PIC_MASTER_ISR) & 0x80)
+			irq = -1;
+	}
+
+	raw_spin_unlock(&i8259A_lock);
+
+	return likely(irq >= 0) ? irq + I8259A_IRQ_BASE : irq;
+}
+
+#endif /* _ASM_I8259_H */
diff --git a/arch/mips/include/asm/ide.h b/arch/mips/include/asm/ide.h
new file mode 100644
index 000000000..bb674c3b0
--- /dev/null
+++ b/arch/mips/include/asm/ide.h
@@ -0,0 +1,13 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * This file contains the MIPS architecture specific IDE code.
+ */
+#ifndef __ASM_IDE_H
+#define __ASM_IDE_H
+
+#include <ide.h>
+
+#endif /* __ASM_IDE_H */
diff --git a/arch/mips/include/asm/idle.h b/arch/mips/include/asm/idle.h
new file mode 100644
index 000000000..0992cad9c
--- /dev/null
+++ b/arch/mips/include/asm/idle.h
@@ -0,0 +1,32 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_IDLE_H
+#define __ASM_IDLE_H
+
+#include <linux/cpuidle.h>
+#include <linux/linkage.h>
+
+extern void (*cpu_wait)(void);
+extern void r4k_wait(void);
+extern asmlinkage void __r4k_wait(void);
+extern void r4k_wait_irqoff(void);
+
+static inline int using_rollback_handler(void)
+{
+	return cpu_wait == r4k_wait;
+}
+
+extern void __init check_wait(void);
+
+extern int mips_cpuidle_wait_enter(struct cpuidle_device *dev,
+				   struct cpuidle_driver *drv, int index);
+
+#define MIPS_CPUIDLE_WAIT_STATE {\
+	.enter			= mips_cpuidle_wait_enter,\
+	.exit_latency		= 1,\
+	.target_residency	= 1,\
+	.power_usage		= UINT_MAX,\
+	.name			= "wait",\
+	.desc			= "MIPS wait",\
+}
+
+#endif /* __ASM_IDLE_H  */
diff --git a/arch/mips/include/asm/inst.h b/arch/mips/include/asm/inst.h
new file mode 100644
index 000000000..2f98ced30
--- /dev/null
+++ b/arch/mips/include/asm/inst.h
@@ -0,0 +1,88 @@
+/*
+ * Format of an instruction in memory.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1996, 2000 by Ralf Baechle
+ * Copyright (C) 2006 by Thiemo Seufer
+ */
+#ifndef _ASM_INST_H
+#define _ASM_INST_H
+
+#include <uapi/asm/inst.h>
+
+/* HACHACHAHCAHC ...  */
+
+/* In case some other massaging is needed, keep MIPSInst as wrapper */
+
+#define MIPSInst(x) x
+
+#define I_OPCODE_SFT	26
+#define MIPSInst_OPCODE(x) (MIPSInst(x) >> I_OPCODE_SFT)
+
+#define I_JTARGET_SFT	0
+#define MIPSInst_JTARGET(x) (MIPSInst(x) & 0x03ffffff)
+
+#define I_RS_SFT	21
+#define MIPSInst_RS(x) ((MIPSInst(x) & 0x03e00000) >> I_RS_SFT)
+
+#define I_RT_SFT	16
+#define MIPSInst_RT(x) ((MIPSInst(x) & 0x001f0000) >> I_RT_SFT)
+
+#define I_IMM_SFT	0
+#define MIPSInst_SIMM(x) ((int)((short)(MIPSInst(x) & 0xffff)))
+#define MIPSInst_UIMM(x) (MIPSInst(x) & 0xffff)
+
+#define I_CACHEOP_SFT	18
+#define MIPSInst_CACHEOP(x) ((MIPSInst(x) & 0x001c0000) >> I_CACHEOP_SFT)
+
+#define I_CACHESEL_SFT	16
+#define MIPSInst_CACHESEL(x) ((MIPSInst(x) & 0x00030000) >> I_CACHESEL_SFT)
+
+#define I_RD_SFT	11
+#define MIPSInst_RD(x) ((MIPSInst(x) & 0x0000f800) >> I_RD_SFT)
+
+#define I_RE_SFT	6
+#define MIPSInst_RE(x) ((MIPSInst(x) & 0x000007c0) >> I_RE_SFT)
+
+#define I_FUNC_SFT	0
+#define MIPSInst_FUNC(x) (MIPSInst(x) & 0x0000003f)
+
+#define I_FFMT_SFT	21
+#define MIPSInst_FFMT(x) ((MIPSInst(x) & 0x01e00000) >> I_FFMT_SFT)
+
+#define I_FT_SFT	16
+#define MIPSInst_FT(x) ((MIPSInst(x) & 0x001f0000) >> I_FT_SFT)
+
+#define I_FS_SFT	11
+#define MIPSInst_FS(x) ((MIPSInst(x) & 0x0000f800) >> I_FS_SFT)
+
+#define I_FD_SFT	6
+#define MIPSInst_FD(x) ((MIPSInst(x) & 0x000007c0) >> I_FD_SFT)
+
+#define I_FR_SFT	21
+#define MIPSInst_FR(x) ((MIPSInst(x) & 0x03e00000) >> I_FR_SFT)
+
+#define I_FMA_FUNC_SFT	3
+#define MIPSInst_FMA_FUNC(x) ((MIPSInst(x) & 0x00000038) >> I_FMA_FUNC_SFT)
+
+#define I_FMA_FFMT_SFT	0
+#define MIPSInst_FMA_FFMT(x) (MIPSInst(x) & 0x00000007)
+
+typedef unsigned int mips_instruction;
+
+/* microMIPS instruction decode structure. Do NOT export!!! */
+struct mm_decoded_insn {
+	mips_instruction insn;
+	mips_instruction next_insn;
+	int pc_inc;
+	int next_pc_inc;
+	int micro_mips_mode;
+};
+
+/* Recode table from 16-bit register notation to 32-bit GPR. Do NOT export!!! */
+extern const int reg16to32[];
+
+#endif /* _ASM_INST_H */
diff --git a/arch/mips/include/asm/io.h b/arch/mips/include/asm/io.h
new file mode 100644
index 000000000..e6d5ccaa3
--- /dev/null
+++ b/arch/mips/include/asm/io.h
@@ -0,0 +1,560 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994, 1995 Waldorf GmbH
+ * Copyright (C) 1994 - 2000, 06 Ralf Baechle
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ * Copyright (C) 2004, 2005  MIPS Technologies, Inc.  All rights reserved.
+ *	Author: Maciej W. Rozycki <macro@mips.com>
+ */
+#ifndef _ASM_IO_H
+#define _ASM_IO_H
+
+#define ARCH_HAS_IOREMAP_WC
+
+#include <linux/compiler.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/irqflags.h>
+
+#include <asm/addrspace.h>
+#include <asm/barrier.h>
+#include <asm/bug.h>
+#include <asm/byteorder.h>
+#include <asm/cpu.h>
+#include <asm/cpu-features.h>
+#include <asm-generic/iomap.h>
+#include <asm/page.h>
+#include <asm/pgtable-bits.h>
+#include <asm/processor.h>
+#include <asm/string.h>
+#include <mangle-port.h>
+
+/*
+ * Raw operations are never swapped in software.  OTOH values that raw
+ * operations are working on may or may not have been swapped by the bus
+ * hardware.  An example use would be for flash memory that's used for
+ * execute in place.
+ */
+# define __raw_ioswabb(a, x)	(x)
+# define __raw_ioswabw(a, x)	(x)
+# define __raw_ioswabl(a, x)	(x)
+# define __raw_ioswabq(a, x)	(x)
+# define ____raw_ioswabq(a, x)	(x)
+
+# define __relaxed_ioswabb ioswabb
+# define __relaxed_ioswabw ioswabw
+# define __relaxed_ioswabl ioswabl
+# define __relaxed_ioswabq ioswabq
+
+/* ioswab[bwlq], __mem_ioswab[bwlq] are defined in mangle-port.h */
+
+/*
+ * On MIPS I/O ports are memory mapped, so we access them using normal
+ * load/store instructions. mips_io_port_base is the virtual address to
+ * which all ports are being mapped.  For sake of efficiency some code
+ * assumes that this is an address that can be loaded with a single lui
+ * instruction, so the lower 16 bits must be zero.  Should be true on
+ * any sane architecture; generic code does not use this assumption.
+ */
+extern unsigned long mips_io_port_base;
+
+static inline void set_io_port_base(unsigned long base)
+{
+	mips_io_port_base = base;
+}
+
+/*
+ * Provide the necessary definitions for generic iomap. We make use of
+ * mips_io_port_base for iomap(), but we don't reserve any low addresses for
+ * use with I/O ports.
+ */
+
+#define HAVE_ARCH_PIO_SIZE
+#define PIO_OFFSET	mips_io_port_base
+#define PIO_MASK	IO_SPACE_LIMIT
+#define PIO_RESERVED	0x0UL
+
+/*
+ * Enforce in-order execution of data I/O.  In the MIPS architecture
+ * these are equivalent to corresponding platform-specific memory
+ * barriers defined in <asm/barrier.h>.  API pinched from PowerPC,
+ * with sync additionally defined.
+ */
+#define iobarrier_rw() mb()
+#define iobarrier_r() rmb()
+#define iobarrier_w() wmb()
+#define iobarrier_sync() iob()
+
+/*
+ *     virt_to_phys    -       map virtual addresses to physical
+ *     @address: address to remap
+ *
+ *     The returned physical address is the physical (CPU) mapping for
+ *     the memory address given. It is only valid to use this function on
+ *     addresses directly mapped or allocated via kmalloc.
+ *
+ *     This function does not give bus mappings for DMA transfers. In
+ *     almost all conceivable cases a device driver should not be using
+ *     this function
+ */
+static inline unsigned long __virt_to_phys_nodebug(volatile const void *address)
+{
+	return __pa(address);
+}
+
+#ifdef CONFIG_DEBUG_VIRTUAL
+extern phys_addr_t __virt_to_phys(volatile const void *x);
+#else
+#define __virt_to_phys(x)	__virt_to_phys_nodebug(x)
+#endif
+
+#define virt_to_phys virt_to_phys
+static inline phys_addr_t virt_to_phys(const volatile void *x)
+{
+	return __virt_to_phys(x);
+}
+
+/*
+ *     phys_to_virt    -       map physical address to virtual
+ *     @address: address to remap
+ *
+ *     The returned virtual address is a current CPU mapping for
+ *     the memory address given. It is only valid to use this function on
+ *     addresses that have a kernel mapping
+ *
+ *     This function does not handle bus mappings for DMA transfers. In
+ *     almost all conceivable cases a device driver should not be using
+ *     this function
+ */
+static inline void * phys_to_virt(unsigned long address)
+{
+	return __va(address);
+}
+
+/*
+ * ISA I/O bus memory addresses are 1:1 with the physical address.
+ */
+static inline unsigned long isa_virt_to_bus(volatile void *address)
+{
+	return virt_to_phys(address);
+}
+
+static inline void *isa_bus_to_virt(unsigned long address)
+{
+	return phys_to_virt(address);
+}
+
+/*
+ * Change "struct page" to physical address.
+ */
+#define page_to_phys(page)	((dma_addr_t)page_to_pfn(page) << PAGE_SHIFT)
+
+void __iomem *ioremap_prot(phys_addr_t offset, unsigned long size,
+		unsigned long prot_val);
+void iounmap(const volatile void __iomem *addr);
+
+/*
+ * ioremap     -   map bus memory into CPU space
+ * @offset:    bus address of the memory
+ * @size:      size of the resource to map
+ *
+ * ioremap performs a platform specific sequence of operations to
+ * make bus memory CPU accessible via the readb/readw/readl/writeb/
+ * writew/writel functions and the other mmio helpers. The returned
+ * address is not guaranteed to be usable directly as a virtual
+ * address.
+ */
+#define ioremap(offset, size)						\
+	ioremap_prot((offset), (size), _CACHE_UNCACHED)
+#define ioremap_uc		ioremap
+
+/*
+ * ioremap_cache -	map bus memory into CPU space
+ * @offset:	    bus address of the memory
+ * @size:	    size of the resource to map
+ *
+ * ioremap_cache performs a platform specific sequence of operations to
+ * make bus memory CPU accessible via the readb/readw/readl/writeb/
+ * writew/writel functions and the other mmio helpers. The returned
+ * address is not guaranteed to be usable directly as a virtual
+ * address.
+ *
+ * This version of ioremap ensures that the memory is marked cachable by
+ * the CPU.  Also enables full write-combining.	 Useful for some
+ * memory-like regions on I/O busses.
+ */
+#define ioremap_cache(offset, size)					\
+	ioremap_prot((offset), (size), _page_cachable_default)
+
+/*
+ * ioremap_wc     -   map bus memory into CPU space
+ * @offset:    bus address of the memory
+ * @size:      size of the resource to map
+ *
+ * ioremap_wc performs a platform specific sequence of operations to
+ * make bus memory CPU accessible via the readb/readw/readl/writeb/
+ * writew/writel functions and the other mmio helpers. The returned
+ * address is not guaranteed to be usable directly as a virtual
+ * address.
+ *
+ * This version of ioremap ensures that the memory is marked uncachable
+ * but accelerated by means of write-combining feature. It is specifically
+ * useful for PCIe prefetchable windows, which may vastly improve a
+ * communications performance. If it was determined on boot stage, what
+ * CPU CCA doesn't support UCA, the method shall fall-back to the
+ * _CACHE_UNCACHED option (see cpu_probe() method).
+ */
+#define ioremap_wc(offset, size)					\
+	ioremap_prot((offset), (size), boot_cpu_data.writecombine)
+
+#if defined(CONFIG_CPU_CAVIUM_OCTEON) || defined(CONFIG_CPU_LOONGSON64)
+#define war_io_reorder_wmb()		wmb()
+#else
+#define war_io_reorder_wmb()		barrier()
+#endif
+
+#define __BUILD_MEMORY_SINGLE(pfx, bwlq, type, barrier, relax, irq)	\
+									\
+static inline void pfx##write##bwlq(type val,				\
+				    volatile void __iomem *mem)		\
+{									\
+	volatile type *__mem;						\
+	type __val;							\
+									\
+	if (barrier)							\
+		iobarrier_rw();						\
+	else								\
+		war_io_reorder_wmb();					\
+									\
+	__mem = (void *)__swizzle_addr_##bwlq((unsigned long)(mem));	\
+									\
+	__val = pfx##ioswab##bwlq(__mem, val);				\
+									\
+	if (sizeof(type) != sizeof(u64) || sizeof(u64) == sizeof(long)) \
+		*__mem = __val;						\
+	else if (cpu_has_64bits) {					\
+		unsigned long __flags;					\
+		type __tmp;						\
+									\
+		if (irq)						\
+			local_irq_save(__flags);			\
+		__asm__ __volatile__(					\
+			".set	push"		"\t\t# __writeq""\n\t"	\
+			".set	arch=r4000"			"\n\t"	\
+			"dsll32 %L0, %L0, 0"			"\n\t"	\
+			"dsrl32 %L0, %L0, 0"			"\n\t"	\
+			"dsll32 %M0, %M0, 0"			"\n\t"	\
+			"or	%L0, %L0, %M0"			"\n\t"	\
+			"sd	%L0, %2"			"\n\t"	\
+			".set	pop"				"\n"	\
+			: "=r" (__tmp)					\
+			: "0" (__val), "m" (*__mem));			\
+		if (irq)						\
+			local_irq_restore(__flags);			\
+	} else								\
+		BUG();							\
+}									\
+									\
+static inline type pfx##read##bwlq(const volatile void __iomem *mem)	\
+{									\
+	volatile type *__mem;						\
+	type __val;							\
+									\
+	__mem = (void *)__swizzle_addr_##bwlq((unsigned long)(mem));	\
+									\
+	if (barrier)							\
+		iobarrier_rw();						\
+									\
+	if (sizeof(type) != sizeof(u64) || sizeof(u64) == sizeof(long)) \
+		__val = *__mem;						\
+	else if (cpu_has_64bits) {					\
+		unsigned long __flags;					\
+									\
+		if (irq)						\
+			local_irq_save(__flags);			\
+		__asm__ __volatile__(					\
+			".set	push"		"\t\t# __readq" "\n\t"	\
+			".set	arch=r4000"			"\n\t"	\
+			"ld	%L0, %1"			"\n\t"	\
+			"dsra32 %M0, %L0, 0"			"\n\t"	\
+			"sll	%L0, %L0, 0"			"\n\t"	\
+			".set	pop"				"\n"	\
+			: "=r" (__val)					\
+			: "m" (*__mem));				\
+		if (irq)						\
+			local_irq_restore(__flags);			\
+	} else {							\
+		__val = 0;						\
+		BUG();							\
+	}								\
+									\
+	/* prevent prefetching of coherent DMA data prematurely */	\
+	if (!relax)							\
+		rmb();							\
+	return pfx##ioswab##bwlq(__mem, __val);				\
+}
+
+#define __BUILD_IOPORT_SINGLE(pfx, bwlq, type, barrier, relax, p)	\
+									\
+static inline void pfx##out##bwlq##p(type val, unsigned long port)	\
+{									\
+	volatile type *__addr;						\
+	type __val;							\
+									\
+	if (barrier)							\
+		iobarrier_rw();						\
+	else								\
+		war_io_reorder_wmb();					\
+									\
+	__addr = (void *)__swizzle_addr_##bwlq(mips_io_port_base + port); \
+									\
+	__val = pfx##ioswab##bwlq(__addr, val);				\
+									\
+	/* Really, we want this to be atomic */				\
+	BUILD_BUG_ON(sizeof(type) > sizeof(unsigned long));		\
+									\
+	*__addr = __val;						\
+}									\
+									\
+static inline type pfx##in##bwlq##p(unsigned long port)			\
+{									\
+	volatile type *__addr;						\
+	type __val;							\
+									\
+	__addr = (void *)__swizzle_addr_##bwlq(mips_io_port_base + port); \
+									\
+	BUILD_BUG_ON(sizeof(type) > sizeof(unsigned long));		\
+									\
+	if (barrier)							\
+		iobarrier_rw();						\
+									\
+	__val = *__addr;						\
+									\
+	/* prevent prefetching of coherent DMA data prematurely */	\
+	if (!relax)							\
+		rmb();							\
+	return pfx##ioswab##bwlq(__addr, __val);			\
+}
+
+#define __BUILD_MEMORY_PFX(bus, bwlq, type, relax)			\
+									\
+__BUILD_MEMORY_SINGLE(bus, bwlq, type, 1, relax, 1)
+
+#define BUILDIO_MEM(bwlq, type)						\
+									\
+__BUILD_MEMORY_PFX(__raw_, bwlq, type, 0)				\
+__BUILD_MEMORY_PFX(__relaxed_, bwlq, type, 1)				\
+__BUILD_MEMORY_PFX(__mem_, bwlq, type, 0)				\
+__BUILD_MEMORY_PFX(, bwlq, type, 0)
+
+BUILDIO_MEM(b, u8)
+BUILDIO_MEM(w, u16)
+BUILDIO_MEM(l, u32)
+#ifdef CONFIG_64BIT
+BUILDIO_MEM(q, u64)
+#else
+__BUILD_MEMORY_PFX(__raw_, q, u64, 0)
+__BUILD_MEMORY_PFX(__mem_, q, u64, 0)
+#endif
+
+#define __BUILD_IOPORT_PFX(bus, bwlq, type)				\
+	__BUILD_IOPORT_SINGLE(bus, bwlq, type, 1, 0,)			\
+	__BUILD_IOPORT_SINGLE(bus, bwlq, type, 1, 0, _p)
+
+#define BUILDIO_IOPORT(bwlq, type)					\
+	__BUILD_IOPORT_PFX(, bwlq, type)				\
+	__BUILD_IOPORT_PFX(__mem_, bwlq, type)
+
+BUILDIO_IOPORT(b, u8)
+BUILDIO_IOPORT(w, u16)
+BUILDIO_IOPORT(l, u32)
+#ifdef CONFIG_64BIT
+BUILDIO_IOPORT(q, u64)
+#endif
+
+#define __BUILDIO(bwlq, type)						\
+									\
+__BUILD_MEMORY_SINGLE(____raw_, bwlq, type, 1, 0, 0)
+
+__BUILDIO(q, u64)
+
+#define readb_relaxed			__relaxed_readb
+#define readw_relaxed			__relaxed_readw
+#define readl_relaxed			__relaxed_readl
+#ifdef CONFIG_64BIT
+#define readq_relaxed			__relaxed_readq
+#endif
+
+#define writeb_relaxed			__relaxed_writeb
+#define writew_relaxed			__relaxed_writew
+#define writel_relaxed			__relaxed_writel
+#ifdef CONFIG_64BIT
+#define writeq_relaxed			__relaxed_writeq
+#endif
+
+#define readb_be(addr)							\
+	__raw_readb((__force unsigned *)(addr))
+#define readw_be(addr)							\
+	be16_to_cpu(__raw_readw((__force unsigned *)(addr)))
+#define readl_be(addr)							\
+	be32_to_cpu(__raw_readl((__force unsigned *)(addr)))
+#define readq_be(addr)							\
+	be64_to_cpu(__raw_readq((__force unsigned *)(addr)))
+
+#define writeb_be(val, addr)						\
+	__raw_writeb((val), (__force unsigned *)(addr))
+#define writew_be(val, addr)						\
+	__raw_writew(cpu_to_be16((val)), (__force unsigned *)(addr))
+#define writel_be(val, addr)						\
+	__raw_writel(cpu_to_be32((val)), (__force unsigned *)(addr))
+#define writeq_be(val, addr)						\
+	__raw_writeq(cpu_to_be64((val)), (__force unsigned *)(addr))
+
+/*
+ * Some code tests for these symbols
+ */
+#ifdef CONFIG_64BIT
+#define readq				readq
+#define writeq				writeq
+#endif
+
+#define __BUILD_MEMORY_STRING(bwlq, type)				\
+									\
+static inline void writes##bwlq(volatile void __iomem *mem,		\
+				const void *addr, unsigned int count)	\
+{									\
+	const volatile type *__addr = addr;				\
+									\
+	while (count--) {						\
+		__mem_write##bwlq(*__addr, mem);			\
+		__addr++;						\
+	}								\
+}									\
+									\
+static inline void reads##bwlq(volatile void __iomem *mem, void *addr,	\
+			       unsigned int count)			\
+{									\
+	volatile type *__addr = addr;					\
+									\
+	while (count--) {						\
+		*__addr = __mem_read##bwlq(mem);			\
+		__addr++;						\
+	}								\
+}
+
+#define __BUILD_IOPORT_STRING(bwlq, type)				\
+									\
+static inline void outs##bwlq(unsigned long port, const void *addr,	\
+			      unsigned int count)			\
+{									\
+	const volatile type *__addr = addr;				\
+									\
+	while (count--) {						\
+		__mem_out##bwlq(*__addr, port);				\
+		__addr++;						\
+	}								\
+}									\
+									\
+static inline void ins##bwlq(unsigned long port, void *addr,		\
+			     unsigned int count)			\
+{									\
+	volatile type *__addr = addr;					\
+									\
+	while (count--) {						\
+		*__addr = __mem_in##bwlq(port);				\
+		__addr++;						\
+	}								\
+}
+
+#define BUILDSTRING(bwlq, type)						\
+									\
+__BUILD_MEMORY_STRING(bwlq, type)					\
+__BUILD_IOPORT_STRING(bwlq, type)
+
+BUILDSTRING(b, u8)
+BUILDSTRING(w, u16)
+BUILDSTRING(l, u32)
+#ifdef CONFIG_64BIT
+BUILDSTRING(q, u64)
+#endif
+
+static inline void memset_io(volatile void __iomem *addr, unsigned char val, int count)
+{
+	memset((void __force *) addr, val, count);
+}
+static inline void memcpy_fromio(void *dst, const volatile void __iomem *src, int count)
+{
+	memcpy(dst, (void __force *) src, count);
+}
+static inline void memcpy_toio(volatile void __iomem *dst, const void *src, int count)
+{
+	memcpy((void __force *) dst, src, count);
+}
+
+/*
+ * The caches on some architectures aren't dma-coherent and have need to
+ * handle this in software.  There are three types of operations that
+ * can be applied to dma buffers.
+ *
+ *  - dma_cache_wback_inv(start, size) makes caches and coherent by
+ *    writing the content of the caches back to memory, if necessary.
+ *    The function also invalidates the affected part of the caches as
+ *    necessary before DMA transfers from outside to memory.
+ *  - dma_cache_wback(start, size) makes caches and coherent by
+ *    writing the content of the caches back to memory, if necessary.
+ *    The function also invalidates the affected part of the caches as
+ *    necessary before DMA transfers from outside to memory.
+ *  - dma_cache_inv(start, size) invalidates the affected parts of the
+ *    caches.  Dirty lines of the caches may be written back or simply
+ *    be discarded.  This operation is necessary before dma operations
+ *    to the memory.
+ *
+ * This API used to be exported; it now is for arch code internal use only.
+ */
+#ifdef CONFIG_DMA_NONCOHERENT
+
+extern void (*_dma_cache_wback_inv)(unsigned long start, unsigned long size);
+extern void (*_dma_cache_wback)(unsigned long start, unsigned long size);
+extern void (*_dma_cache_inv)(unsigned long start, unsigned long size);
+
+#define dma_cache_wback_inv(start, size)	_dma_cache_wback_inv(start, size)
+#define dma_cache_wback(start, size)		_dma_cache_wback(start, size)
+#define dma_cache_inv(start, size)		_dma_cache_inv(start, size)
+
+#else /* Sane hardware */
+
+#define dma_cache_wback_inv(start,size) \
+	do { (void) (start); (void) (size); } while (0)
+#define dma_cache_wback(start,size)	\
+	do { (void) (start); (void) (size); } while (0)
+#define dma_cache_inv(start,size)	\
+	do { (void) (start); (void) (size); } while (0)
+
+#endif /* CONFIG_DMA_NONCOHERENT */
+
+/*
+ * Read a 32-bit register that requires a 64-bit read cycle on the bus.
+ * Avoid interrupt mucking, just adjust the address for 4-byte access.
+ * Assume the addresses are 8-byte aligned.
+ */
+#ifdef __MIPSEB__
+#define __CSR_32_ADJUST 4
+#else
+#define __CSR_32_ADJUST 0
+#endif
+
+#define csr_out32(v, a) (*(volatile u32 *)((unsigned long)(a) + __CSR_32_ADJUST) = (v))
+#define csr_in32(a)    (*(volatile u32 *)((unsigned long)(a) + __CSR_32_ADJUST))
+
+/*
+ * Convert a physical pointer to a virtual kernel pointer for /dev/mem
+ * access
+ */
+#define xlate_dev_mem_ptr(p)	__va(p)
+
+void __ioread64_copy(void *to, const void __iomem *from, size_t count);
+
+#endif /* _ASM_IO_H */
diff --git a/arch/mips/include/asm/ip32/crime.h b/arch/mips/include/asm/ip32/crime.h
new file mode 100644
index 000000000..16c94a27b
--- /dev/null
+++ b/arch/mips/include/asm/ip32/crime.h
@@ -0,0 +1,158 @@
+/*
+ * Definitions for the SGI CRIME (CPU, Rendering, Interconnect and Memory
+ * Engine)
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2000 Harald Koerfgen
+ */
+
+#ifndef __ASM_CRIME_H__
+#define __ASM_CRIME_H__
+
+/*
+ * Address map
+ */
+#define CRIME_BASE	0x14000000	/* physical */
+
+struct sgi_crime {
+	volatile unsigned long id;
+#define CRIME_ID_MASK			0xff
+#define CRIME_ID_IDBITS			0xf0
+#define CRIME_ID_IDVALUE		0xa0
+#define CRIME_ID_REV			0x0f
+#define CRIME_REV_PETTY			0x00
+#define CRIME_REV_11			0x11
+#define CRIME_REV_13			0x13
+#define CRIME_REV_14			0x14
+
+	volatile unsigned long control;
+#define CRIME_CONTROL_MASK		0x3fff
+#define CRIME_CONTROL_TRITON_SYSADC	0x2000
+#define CRIME_CONTROL_CRIME_SYSADC	0x1000
+#define CRIME_CONTROL_HARD_RESET	0x0800
+#define CRIME_CONTROL_SOFT_RESET	0x0400
+#define CRIME_CONTROL_DOG_ENA		0x0200
+#define CRIME_CONTROL_ENDIANESS		0x0100
+#define CRIME_CONTROL_ENDIAN_BIG	0x0100
+#define CRIME_CONTROL_ENDIAN_LITTLE	0x0000
+#define CRIME_CONTROL_CQUEUE_HWM	0x000f
+#define CRIME_CONTROL_CQUEUE_SHFT	0
+#define CRIME_CONTROL_WBUF_HWM		0x00f0
+#define CRIME_CONTROL_WBUF_SHFT		8
+
+	volatile unsigned long istat;
+	volatile unsigned long imask;
+	volatile unsigned long soft_int;
+	volatile unsigned long hard_int;
+#define MACE_VID_IN1_INT		BIT(0)
+#define MACE_VID_IN2_INT		BIT(1)
+#define MACE_VID_OUT_INT		BIT(2)
+#define MACE_ETHERNET_INT		BIT(3)
+#define MACE_SUPERIO_INT		BIT(4)
+#define MACE_MISC_INT			BIT(5)
+#define MACE_AUDIO_INT			BIT(6)
+#define MACE_PCI_BRIDGE_INT		BIT(7)
+#define MACEPCI_SCSI0_INT		BIT(8)
+#define MACEPCI_SCSI1_INT		BIT(9)
+#define MACEPCI_SLOT0_INT		BIT(10)
+#define MACEPCI_SLOT1_INT		BIT(11)
+#define MACEPCI_SLOT2_INT		BIT(12)
+#define MACEPCI_SHARED0_INT		BIT(13)
+#define MACEPCI_SHARED1_INT		BIT(14)
+#define MACEPCI_SHARED2_INT		BIT(15)
+#define CRIME_GBE0_INT			BIT(16)
+#define CRIME_GBE1_INT			BIT(17)
+#define CRIME_GBE2_INT			BIT(18)
+#define CRIME_GBE3_INT			BIT(19)
+#define CRIME_CPUERR_INT		BIT(20)
+#define CRIME_MEMERR_INT		BIT(21)
+#define CRIME_RE_EMPTY_E_INT		BIT(22)
+#define CRIME_RE_FULL_E_INT		BIT(23)
+#define CRIME_RE_IDLE_E_INT		BIT(24)
+#define CRIME_RE_EMPTY_L_INT		BIT(25)
+#define CRIME_RE_FULL_L_INT		BIT(26)
+#define CRIME_RE_IDLE_L_INT		BIT(27)
+#define CRIME_SOFT0_INT			BIT(28)
+#define CRIME_SOFT1_INT			BIT(29)
+#define CRIME_SOFT2_INT			BIT(30)
+#define CRIME_SYSCORERR_INT		CRIME_SOFT2_INT
+#define CRIME_VICE_INT			BIT(31)
+/* Masks for deciding who handles the interrupt */
+#define CRIME_MACE_INT_MASK		0x8f
+#define CRIME_MACEISA_INT_MASK		0x70
+#define CRIME_MACEPCI_INT_MASK		0xff00
+#define CRIME_CRIME_INT_MASK		0xffff0000
+
+	volatile unsigned long watchdog;
+#define CRIME_DOG_POWER_ON_RESET	0x00010000
+#define CRIME_DOG_WARM_RESET		0x00080000
+#define CRIME_DOG_TIMEOUT		(CRIME_DOG_POWER_ON_RESET|CRIME_DOG_WARM_RESET)
+#define CRIME_DOG_VALUE			0x00007fff
+
+	volatile unsigned long timer;
+#define CRIME_MASTER_FREQ		66666500	/* Crime upcounter frequency */
+#define CRIME_NS_PER_TICK		15		/* for delay_calibrate */
+
+	volatile unsigned long cpu_error_addr;
+#define CRIME_CPU_ERROR_ADDR_MASK	0x3ffffffff
+
+	volatile unsigned long cpu_error_stat;
+#define CRIME_CPU_ERROR_MASK		0x7		/* cpu error stat is 3 bits */
+#define CRIME_CPU_ERROR_CPU_ILL_ADDR	0x4
+#define CRIME_CPU_ERROR_VICE_WRT_PRTY	0x2
+#define CRIME_CPU_ERROR_CPU_WRT_PRTY	0x1
+
+	unsigned long _pad0[54];
+
+	volatile unsigned long mc_ctrl;
+	volatile unsigned long bank_ctrl[8];
+#define CRIME_MEM_BANK_CONTROL_MASK		0x11f	/* 9 bits 7:5 reserved */
+#define CRIME_MEM_BANK_CONTROL_ADDR		0x01f
+#define CRIME_MEM_BANK_CONTROL_SDRAM_SIZE	0x100
+#define CRIME_MAXBANKS				8
+
+	volatile unsigned long mem_ref_counter;
+#define CRIME_MEM_REF_COUNTER_MASK	0x3ff		/* 10bit */
+
+	volatile unsigned long mem_error_stat;
+#define CRIME_MEM_ERROR_STAT_MASK	0x0ff7ffff	/* 28-bit register */
+#define CRIME_MEM_ERROR_MACE_ID		0x0000007f
+#define CRIME_MEM_ERROR_MACE_ACCESS	0x00000080
+#define CRIME_MEM_ERROR_RE_ID		0x00007f00
+#define CRIME_MEM_ERROR_RE_ACCESS	0x00008000
+#define CRIME_MEM_ERROR_GBE_ACCESS	0x00010000
+#define CRIME_MEM_ERROR_VICE_ACCESS	0x00020000
+#define CRIME_MEM_ERROR_CPU_ACCESS	0x00040000
+#define CRIME_MEM_ERROR_RESERVED	0x00080000
+#define CRIME_MEM_ERROR_SOFT_ERR	0x00100000
+#define CRIME_MEM_ERROR_HARD_ERR	0x00200000
+#define CRIME_MEM_ERROR_MULTIPLE	0x00400000
+#define CRIME_MEM_ERROR_ECC		0x01800000
+#define CRIME_MEM_ERROR_MEM_ECC_RD	0x00800000
+#define CRIME_MEM_ERROR_MEM_ECC_RMW	0x01000000
+#define CRIME_MEM_ERROR_INV		0x0e000000
+#define CRIME_MEM_ERROR_INV_MEM_ADDR_RD 0x02000000
+#define CRIME_MEM_ERROR_INV_MEM_ADDR_WR 0x04000000
+#define CRIME_MEM_ERROR_INV_MEM_ADDR_RMW 0x08000000
+
+	volatile unsigned long mem_error_addr;
+#define CRIME_MEM_ERROR_ADDR_MASK	0x3fffffff
+
+	volatile unsigned long mem_ecc_syn;
+#define CRIME_MEM_ERROR_ECC_SYN_MASK	0xffffffff
+
+	volatile unsigned long mem_ecc_chk;
+#define CRIME_MEM_ERROR_ECC_CHK_MASK	0xffffffff
+
+	volatile unsigned long mem_ecc_repl;
+#define CRIME_MEM_ERROR_ECC_REPL_MASK	0xffffffff
+};
+
+extern struct sgi_crime __iomem *crime;
+
+#define CRIME_HI_MEM_BASE	0x40000000	/* this is where whole 1G of RAM is mapped */
+
+#endif /* __ASM_CRIME_H__ */
diff --git a/arch/mips/include/asm/ip32/ip32_ints.h b/arch/mips/include/asm/ip32/ip32_ints.h
new file mode 100644
index 000000000..72e3368de
--- /dev/null
+++ b/arch/mips/include/asm/ip32/ip32_ints.h
@@ -0,0 +1,114 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2000 Harald Koerfgen
+ */
+
+#ifndef __ASM_IP32_INTS_H
+#define __ASM_IP32_INTS_H
+
+#include <asm/irq.h>
+
+/*
+ * This list reflects the assignment of interrupt numbers to
+ * interrupting events.	 Order is fairly irrelevant to handling
+ * priority.  This differs from irix.
+ */
+
+enum ip32_irq_no {
+	/*
+	 * CPU interrupts are 0 ... 7
+	 */
+
+	CRIME_IRQ_BASE			= MIPS_CPU_IRQ_BASE + 8,
+
+	/*
+	 * MACE
+	 */
+	MACE_VID_IN1_IRQ		= CRIME_IRQ_BASE,
+	MACE_VID_IN2_IRQ,
+	MACE_VID_OUT_IRQ,
+	MACE_ETHERNET_IRQ,
+	/* SUPERIO, MISC, and AUDIO are MACEISA */
+	__MACE_SUPERIO,
+	__MACE_MISC,
+	__MACE_AUDIO,
+	MACE_PCI_BRIDGE_IRQ,
+
+	/*
+	 * MACEPCI
+	 */
+	MACEPCI_SCSI0_IRQ,
+	MACEPCI_SCSI1_IRQ,
+	MACEPCI_SLOT0_IRQ,
+	MACEPCI_SLOT1_IRQ,
+	MACEPCI_SLOT2_IRQ,
+	MACEPCI_SHARED0_IRQ,
+	MACEPCI_SHARED1_IRQ,
+	MACEPCI_SHARED2_IRQ,
+
+	/*
+	 * CRIME
+	 */
+	CRIME_GBE0_IRQ,
+	CRIME_GBE1_IRQ,
+	CRIME_GBE2_IRQ,
+	CRIME_GBE3_IRQ,
+	CRIME_CPUERR_IRQ,
+	CRIME_MEMERR_IRQ,
+	CRIME_RE_EMPTY_E_IRQ,
+	CRIME_RE_FULL_E_IRQ,
+	CRIME_RE_IDLE_E_IRQ,
+	CRIME_RE_EMPTY_L_IRQ,
+	CRIME_RE_FULL_L_IRQ,
+	CRIME_RE_IDLE_L_IRQ,
+	CRIME_SOFT0_IRQ,
+	CRIME_SOFT1_IRQ,
+	CRIME_SOFT2_IRQ,
+	CRIME_SYSCORERR_IRQ		= CRIME_SOFT2_IRQ,
+	CRIME_VICE_IRQ,
+
+	/*
+	 * MACEISA
+	 */
+	MACEISA_AUDIO_SW_IRQ,
+	MACEISA_AUDIO_SC_IRQ,
+	MACEISA_AUDIO1_DMAT_IRQ,
+	MACEISA_AUDIO1_OF_IRQ,
+	MACEISA_AUDIO2_DMAT_IRQ,
+	MACEISA_AUDIO2_MERR_IRQ,
+	MACEISA_AUDIO3_DMAT_IRQ,
+	MACEISA_AUDIO3_MERR_IRQ,
+	MACEISA_RTC_IRQ,
+	MACEISA_KEYB_IRQ,
+	/* MACEISA_KEYB_POLL is not an IRQ */
+	__MACEISA_KEYB_POLL,
+	MACEISA_MOUSE_IRQ,
+	/* MACEISA_MOUSE_POLL is not an IRQ */
+	__MACEISA_MOUSE_POLL,
+	MACEISA_TIMER0_IRQ,
+	MACEISA_TIMER1_IRQ,
+	MACEISA_TIMER2_IRQ,
+	MACEISA_PARALLEL_IRQ,
+	MACEISA_PAR_CTXA_IRQ,
+	MACEISA_PAR_CTXB_IRQ,
+	MACEISA_PAR_MERR_IRQ,
+	MACEISA_SERIAL1_IRQ,
+	MACEISA_SERIAL1_TDMAT_IRQ,
+	MACEISA_SERIAL1_TDMAPR_IRQ,
+	MACEISA_SERIAL1_TDMAME_IRQ,
+	MACEISA_SERIAL1_RDMAT_IRQ,
+	MACEISA_SERIAL1_RDMAOR_IRQ,
+	MACEISA_SERIAL2_IRQ,
+	MACEISA_SERIAL2_TDMAT_IRQ,
+	MACEISA_SERIAL2_TDMAPR_IRQ,
+	MACEISA_SERIAL2_TDMAME_IRQ,
+	MACEISA_SERIAL2_RDMAT_IRQ,
+	MACEISA_SERIAL2_RDMAOR_IRQ,
+
+	IP32_IRQ_MAX			= MACEISA_SERIAL2_RDMAOR_IRQ
+};
+
+#endif /* __ASM_IP32_INTS_H */
diff --git a/arch/mips/include/asm/ip32/mace.h b/arch/mips/include/asm/ip32/mace.h
new file mode 100644
index 000000000..253ed7ea8
--- /dev/null
+++ b/arch/mips/include/asm/ip32/mace.h
@@ -0,0 +1,365 @@
+/*
+ * Definitions for the SGI MACE (Multimedia, Audio and Communications Engine)
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2000 Harald Koerfgen
+ * Copyright (C) 2004 Ladislav Michl
+ */
+
+#ifndef __ASM_MACE_H__
+#define __ASM_MACE_H__
+
+/*
+ * Address map
+ */
+#define MACE_BASE	0x1f000000	/* physical */
+
+/*
+ * PCI interface
+ */
+struct mace_pci {
+	volatile unsigned int error_addr;
+	volatile unsigned int error;
+#define MACEPCI_ERROR_MASTER_ABORT		BIT(31)
+#define MACEPCI_ERROR_TARGET_ABORT		BIT(30)
+#define MACEPCI_ERROR_DATA_PARITY_ERR		BIT(29)
+#define MACEPCI_ERROR_RETRY_ERR			BIT(28)
+#define MACEPCI_ERROR_ILLEGAL_CMD		BIT(27)
+#define MACEPCI_ERROR_SYSTEM_ERR		BIT(26)
+#define MACEPCI_ERROR_INTERRUPT_TEST		BIT(25)
+#define MACEPCI_ERROR_PARITY_ERR		BIT(24)
+#define MACEPCI_ERROR_OVERRUN			BIT(23)
+#define MACEPCI_ERROR_RSVD			BIT(22)
+#define MACEPCI_ERROR_MEMORY_ADDR		BIT(21)
+#define MACEPCI_ERROR_CONFIG_ADDR		BIT(20)
+#define MACEPCI_ERROR_MASTER_ABORT_ADDR_VALID	BIT(19)
+#define MACEPCI_ERROR_TARGET_ABORT_ADDR_VALID	BIT(18)
+#define MACEPCI_ERROR_DATA_PARITY_ADDR_VALID	BIT(17)
+#define MACEPCI_ERROR_RETRY_ADDR_VALID		BIT(16)
+#define MACEPCI_ERROR_SIG_TABORT		BIT(4)
+#define MACEPCI_ERROR_DEVSEL_MASK		0xc0
+#define MACEPCI_ERROR_DEVSEL_FAST		0
+#define MACEPCI_ERROR_DEVSEL_MED		0x40
+#define MACEPCI_ERROR_DEVSEL_SLOW		0x80
+#define MACEPCI_ERROR_FBB			BIT(1)
+#define MACEPCI_ERROR_66MHZ			BIT(0)
+	volatile unsigned int control;
+#define MACEPCI_CONTROL_INT(x)			BIT(x)
+#define MACEPCI_CONTROL_INT_MASK		0xff
+#define MACEPCI_CONTROL_SERR_ENA		BIT(8)
+#define MACEPCI_CONTROL_ARB_N6			BIT(9)
+#define MACEPCI_CONTROL_PARITY_ERR		BIT(10)
+#define MACEPCI_CONTROL_MRMRA_ENA		BIT(11)
+#define MACEPCI_CONTROL_ARB_N3			BIT(12)
+#define MACEPCI_CONTROL_ARB_N4			BIT(13)
+#define MACEPCI_CONTROL_ARB_N5			BIT(14)
+#define MACEPCI_CONTROL_PARK_LIU		BIT(15)
+#define MACEPCI_CONTROL_INV_INT(x)		BIT(16+x)
+#define MACEPCI_CONTROL_INV_INT_MASK		0x00ff0000
+#define MACEPCI_CONTROL_OVERRUN_INT		BIT(24)
+#define MACEPCI_CONTROL_PARITY_INT		BIT(25)
+#define MACEPCI_CONTROL_SERR_INT		BIT(26)
+#define MACEPCI_CONTROL_IT_INT			BIT(27)
+#define MACEPCI_CONTROL_RE_INT			BIT(28)
+#define MACEPCI_CONTROL_DPED_INT		BIT(29)
+#define MACEPCI_CONTROL_TAR_INT			BIT(30)
+#define MACEPCI_CONTROL_MAR_INT			BIT(31)
+	volatile unsigned int rev;
+	unsigned int _pad[0xcf8/4 - 4];
+	volatile unsigned int config_addr;
+	union {
+		volatile unsigned char b[4];
+		volatile unsigned short w[2];
+		volatile unsigned int l;
+	} config_data;
+};
+#define MACEPCI_LOW_MEMORY		0x1a000000
+#define MACEPCI_LOW_IO			0x18000000
+#define MACEPCI_SWAPPED_VIEW		0
+#define MACEPCI_NATIVE_VIEW		0x40000000
+#define MACEPCI_IO			0x80000000
+#define MACEPCI_HI_MEMORY		0x280000000
+#define MACEPCI_HI_IO			0x100000000
+
+/*
+ * Video interface
+ */
+struct mace_video {
+	unsigned long xxx;	/* later... */
+};
+
+/*
+ * Ethernet interface
+ */
+struct mace_ethernet {
+	volatile u64 mac_ctrl;
+	volatile unsigned long int_stat;
+	volatile unsigned long dma_ctrl;
+	volatile unsigned long timer;
+	volatile unsigned long tx_int_al;
+	volatile unsigned long rx_int_al;
+	volatile unsigned long tx_info;
+	volatile unsigned long tx_info_al;
+	volatile unsigned long rx_buff;
+	volatile unsigned long rx_buff_al1;
+	volatile unsigned long rx_buff_al2;
+	volatile unsigned long diag;
+	volatile unsigned long phy_data;
+	volatile unsigned long phy_regs;
+	volatile unsigned long phy_trans_go;
+	volatile unsigned long backoff_seed;
+	/*===================================*/
+	volatile unsigned long imq_reserved[4];
+	volatile unsigned long mac_addr;
+	volatile unsigned long mac_addr2;
+	volatile unsigned long mcast_filter;
+	volatile unsigned long tx_ring_base;
+	/* Following are read-only registers for debugging */
+	volatile unsigned long tx_pkt1_hdr;
+	volatile unsigned long tx_pkt1_ptr[3];
+	volatile unsigned long tx_pkt2_hdr;
+	volatile unsigned long tx_pkt2_ptr[3];
+	/*===================================*/
+	volatile unsigned long rx_fifo;
+};
+
+/*
+ * Peripherals
+ */
+
+/* Audio registers */
+struct mace_audio {
+	volatile unsigned long control;
+	volatile unsigned long codec_control;		/* codec status control */
+	volatile unsigned long codec_mask;		/* codec status input mask */
+	volatile unsigned long codec_read;		/* codec status read data */
+	struct {
+		volatile unsigned long control;		/* channel control */
+		volatile unsigned long read_ptr;	/* channel read pointer */
+		volatile unsigned long write_ptr;	/* channel write pointer */
+		volatile unsigned long depth;		/* channel depth */
+	} chan[3];
+};
+
+
+/* register definitions for parallel port DMA */
+struct mace_parport {
+	/* 0 - do nothing,
+	 * 1 - pulse terminal count to the device after buffer is drained */
+#define MACEPAR_CONTEXT_LASTFLAG	BIT(63)
+	/* Should not cross 4K page boundary */
+#define MACEPAR_CONTEXT_DATA_BOUND	0x0000000000001000UL
+#define MACEPAR_CONTEXT_DATALEN_MASK	0x00000fff00000000UL
+#define MACEPAR_CONTEXT_DATALEN_SHIFT	32
+	/* Can be arbitrarily aligned on any byte boundary on output,
+	 * 64 byte aligned on input */
+#define MACEPAR_CONTEXT_BASEADDR_MASK	0x00000000ffffffffUL
+	volatile u64 context_a;
+	volatile u64 context_b;
+	/* 0 - mem->device, 1 - device->mem */
+#define MACEPAR_CTLSTAT_DIRECTION	BIT(0)
+	/* 0 - channel frozen, 1 - channel enabled */
+#define MACEPAR_CTLSTAT_ENABLE		BIT(1)
+	/* 0 - channel active, 1 - complete channel reset */
+#define MACEPAR_CTLSTAT_RESET		BIT(2)
+#define MACEPAR_CTLSTAT_CTXB_VALID	BIT(3)
+#define MACEPAR_CTLSTAT_CTXA_VALID	BIT(4)
+	volatile u64 cntlstat;		/* Control/Status register */
+#define MACEPAR_DIAG_CTXINUSE		BIT(0)
+	/* 1 - Dma engine is enabled and processing something */
+#define MACEPAR_DIAG_DMACTIVE		BIT(1)
+	/* Counter of bytes left */
+#define MACEPAR_DIAG_CTRMASK		0x0000000000003ffcUL
+#define MACEPAR_DIAG_CTRSHIFT		2
+	volatile u64 diagnostic;	/* RO: diagnostic register */
+};
+
+/* ISA Control and DMA registers */
+struct mace_isactrl {
+	volatile unsigned long ringbase;
+#define MACEISA_RINGBUFFERS_SIZE	(8 * 4096)
+
+	volatile unsigned long misc;
+#define MACEISA_FLASH_WE		BIT(0)	/* 1=> Enable FLASH writes */
+#define MACEISA_PWD_CLEAR		BIT(1)	/* 1=> PWD CLEAR jumper detected */
+#define MACEISA_NIC_DEASSERT		BIT(2)
+#define MACEISA_NIC_DATA		BIT(3)
+#define MACEISA_LED_RED			BIT(4)	/* 0=> Illuminate red LED */
+#define MACEISA_LED_GREEN		BIT(5)	/* 0=> Illuminate green LED */
+#define MACEISA_DP_RAM_ENABLE		BIT(6)
+
+	volatile unsigned long istat;
+	volatile unsigned long imask;
+#define MACEISA_AUDIO_SW_INT		BIT(0)
+#define MACEISA_AUDIO_SC_INT		BIT(1)
+#define MACEISA_AUDIO1_DMAT_INT		BIT(2)
+#define MACEISA_AUDIO1_OF_INT		BIT(3)
+#define MACEISA_AUDIO2_DMAT_INT		BIT(4)
+#define MACEISA_AUDIO2_MERR_INT		BIT(5)
+#define MACEISA_AUDIO3_DMAT_INT		BIT(6)
+#define MACEISA_AUDIO3_MERR_INT		BIT(7)
+#define MACEISA_RTC_INT			BIT(8)
+#define MACEISA_KEYB_INT		BIT(9)
+#define MACEISA_KEYB_POLL_INT		BIT(10)
+#define MACEISA_MOUSE_INT		BIT(11)
+#define MACEISA_MOUSE_POLL_INT		BIT(12)
+#define MACEISA_TIMER0_INT		BIT(13)
+#define MACEISA_TIMER1_INT		BIT(14)
+#define MACEISA_TIMER2_INT		BIT(15)
+#define MACEISA_PARALLEL_INT		BIT(16)
+#define MACEISA_PAR_CTXA_INT		BIT(17)
+#define MACEISA_PAR_CTXB_INT		BIT(18)
+#define MACEISA_PAR_MERR_INT		BIT(19)
+#define MACEISA_SERIAL1_INT		BIT(20)
+#define MACEISA_SERIAL1_TDMAT_INT	BIT(21)
+#define MACEISA_SERIAL1_TDMAPR_INT	BIT(22)
+#define MACEISA_SERIAL1_TDMAME_INT	BIT(23)
+#define MACEISA_SERIAL1_RDMAT_INT	BIT(24)
+#define MACEISA_SERIAL1_RDMAOR_INT	BIT(25)
+#define MACEISA_SERIAL2_INT		BIT(26)
+#define MACEISA_SERIAL2_TDMAT_INT	BIT(27)
+#define MACEISA_SERIAL2_TDMAPR_INT	BIT(28)
+#define MACEISA_SERIAL2_TDMAME_INT	BIT(29)
+#define MACEISA_SERIAL2_RDMAT_INT	BIT(30)
+#define MACEISA_SERIAL2_RDMAOR_INT	BIT(31)
+
+	volatile unsigned long _pad[0x2000/8 - 4];
+
+	volatile unsigned long dp_ram[0x400];
+	struct mace_parport parport;
+};
+
+/* Keyboard & Mouse registers
+ * -> drivers/input/serio/maceps2.c */
+struct mace_ps2port {
+	volatile unsigned long tx;
+	volatile unsigned long rx;
+	volatile unsigned long control;
+	volatile unsigned long status;
+};
+
+struct mace_ps2 {
+	struct mace_ps2port keyb;
+	struct mace_ps2port mouse;
+};
+
+/* I2C registers
+ * -> drivers/i2c/algos/i2c-algo-sgi.c */
+struct mace_i2c {
+	volatile unsigned long config;
+#define MACEI2C_RESET		BIT(0)
+#define MACEI2C_FAST		BIT(1)
+#define MACEI2C_DATA_OVERRIDE	BIT(2)
+#define MACEI2C_CLOCK_OVERRIDE	BIT(3)
+#define MACEI2C_DATA_STATUS	BIT(4)
+#define MACEI2C_CLOCK_STATUS	BIT(5)
+	volatile unsigned long control;
+	volatile unsigned long data;
+};
+
+/* Timer registers */
+typedef union {
+	volatile unsigned long ust_msc;
+	struct reg {
+		volatile unsigned int ust;
+		volatile unsigned int msc;
+	} reg;
+} timer_reg;
+
+struct mace_timers {
+	volatile unsigned long ust;
+#define MACE_UST_PERIOD_NS	960
+
+	volatile unsigned long compare1;
+	volatile unsigned long compare2;
+	volatile unsigned long compare3;
+
+	timer_reg audio_in;
+	timer_reg audio_out1;
+	timer_reg audio_out2;
+	timer_reg video_in1;
+	timer_reg video_in2;
+	timer_reg video_out;
+};
+
+struct mace_perif {
+	struct mace_audio audio;
+	char _pad0[0x10000 - sizeof(struct mace_audio)];
+
+	struct mace_isactrl ctrl;
+	char _pad1[0x10000 - sizeof(struct mace_isactrl)];
+
+	struct mace_ps2 ps2;
+	char _pad2[0x10000 - sizeof(struct mace_ps2)];
+
+	struct mace_i2c i2c;
+	char _pad3[0x10000 - sizeof(struct mace_i2c)];
+
+	struct mace_timers timers;
+	char _pad4[0x10000 - sizeof(struct mace_timers)];
+};
+
+
+/*
+ * ISA peripherals
+ */
+
+/* Parallel port */
+struct mace_parallel {
+};
+
+struct mace_ecp1284 {	/* later... */
+};
+
+/* Serial port */
+struct mace_serial {
+	volatile unsigned long xxx;	/* later... */
+};
+
+struct mace_isa {
+	struct mace_parallel parallel;
+	char _pad1[0x8000 - sizeof(struct mace_parallel)];
+
+	struct mace_ecp1284 ecp1284;
+	char _pad2[0x8000 - sizeof(struct mace_ecp1284)];
+
+	struct mace_serial serial1;
+	char _pad3[0x8000 - sizeof(struct mace_serial)];
+
+	struct mace_serial serial2;
+	char _pad4[0x8000 - sizeof(struct mace_serial)];
+
+	volatile unsigned char rtc[0x10000];
+};
+
+struct sgi_mace {
+	char _reserved[0x80000];
+
+	struct mace_pci pci;
+	char _pad0[0x80000 - sizeof(struct mace_pci)];
+
+	struct mace_video video_in1;
+	char _pad1[0x80000 - sizeof(struct mace_video)];
+
+	struct mace_video video_in2;
+	char _pad2[0x80000 - sizeof(struct mace_video)];
+
+	struct mace_video video_out;
+	char _pad3[0x80000 - sizeof(struct mace_video)];
+
+	struct mace_ethernet eth;
+	char _pad4[0x80000 - sizeof(struct mace_ethernet)];
+
+	struct mace_perif perif;
+	char _pad5[0x80000 - sizeof(struct mace_perif)];
+
+	struct mace_isa isa;
+	char _pad6[0x80000 - sizeof(struct mace_isa)];
+};
+
+extern struct sgi_mace __iomem *mace;
+
+#endif /* __ASM_MACE_H__ */
diff --git a/arch/mips/include/asm/irq.h b/arch/mips/include/asm/irq.h
new file mode 100644
index 000000000..44f9824c1
--- /dev/null
+++ b/arch/mips/include/asm/irq.h
@@ -0,0 +1,84 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994 by Waldorf GMBH, written by Ralf Baechle
+ * Copyright (C) 1995, 96, 97, 98, 99, 2000, 01, 02, 03 by Ralf Baechle
+ */
+#ifndef _ASM_IRQ_H
+#define _ASM_IRQ_H
+
+#include <linux/linkage.h>
+#include <linux/smp.h>
+
+#include <asm/mipsmtregs.h>
+
+#include <irq.h>
+
+#define IRQ_STACK_SIZE			THREAD_SIZE
+#define IRQ_STACK_START			(IRQ_STACK_SIZE - 16)
+
+extern void __init init_IRQ(void);
+extern void *irq_stack[NR_CPUS];
+
+/*
+ * The highest address on the IRQ stack contains a dummy frame put down in
+ * genex.S (handle_int & except_vec_vi_handler) which is structured as follows:
+ *
+ *   top ------------
+ *       | task sp  | <- irq_stack[cpu] + IRQ_STACK_START
+ *       ------------
+ *       |          | <- First frame of IRQ context
+ *       ------------
+ *
+ * task sp holds a copy of the task stack pointer where the struct pt_regs
+ * from exception entry can be found.
+ */
+
+static inline bool on_irq_stack(int cpu, unsigned long sp)
+{
+	unsigned long low = (unsigned long)irq_stack[cpu];
+	unsigned long high = low + IRQ_STACK_SIZE;
+
+	return (low <= sp && sp <= high);
+}
+
+#ifdef CONFIG_I8259
+static inline int irq_canonicalize(int irq)
+{
+	return ((irq == I8259A_IRQ_BASE + 2) ? I8259A_IRQ_BASE + 9 : irq);
+}
+#else
+#define irq_canonicalize(irq) (irq)	/* Sane hardware, sane code ... */
+#endif
+
+asmlinkage void plat_irq_dispatch(void);
+
+extern void do_IRQ(unsigned int irq);
+
+struct irq_domain;
+extern void do_domain_IRQ(struct irq_domain *domain, unsigned int irq);
+
+extern void arch_init_irq(void);
+extern void spurious_interrupt(void);
+
+/*
+ * Before R2 the timer and performance counter interrupts were both fixed to
+ * IE7.	 Since R2 their number has to be read from the c0_intctl register.
+ */
+#define CP0_LEGACY_COMPARE_IRQ 7
+#define CP0_LEGACY_PERFCNT_IRQ 7
+
+extern int cp0_compare_irq;
+extern int cp0_compare_irq_shift;
+extern int cp0_perfcount_irq;
+extern int cp0_fdc_irq;
+
+extern int get_c0_fdc_int(void);
+
+void arch_trigger_cpumask_backtrace(const struct cpumask *mask,
+				    bool exclude_self);
+#define arch_trigger_cpumask_backtrace arch_trigger_cpumask_backtrace
+
+#endif /* _ASM_IRQ_H */
diff --git a/arch/mips/include/asm/irq_cpu.h b/arch/mips/include/asm/irq_cpu.h
new file mode 100644
index 000000000..83d7331ab
--- /dev/null
+++ b/arch/mips/include/asm/irq_cpu.h
@@ -0,0 +1,20 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ *	include/asm-mips/irq_cpu.h
+ *
+ *	MIPS CPU interrupt definitions.
+ *
+ *	Copyright (C) 2002  Maciej W. Rozycki
+ */
+#ifndef _ASM_IRQ_CPU_H
+#define _ASM_IRQ_CPU_H
+
+extern void mips_cpu_irq_init(void);
+
+#ifdef CONFIG_IRQ_DOMAIN
+struct device_node;
+extern int mips_cpu_irq_of_init(struct device_node *of_node,
+				struct device_node *parent);
+#endif
+
+#endif /* _ASM_IRQ_CPU_H */
diff --git a/arch/mips/include/asm/irq_gt641xx.h b/arch/mips/include/asm/irq_gt641xx.h
new file mode 100644
index 000000000..d689c1c6c
--- /dev/null
+++ b/arch/mips/include/asm/irq_gt641xx.h
@@ -0,0 +1,47 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ *  Galileo/Marvell GT641xx IRQ definitions.
+ *
+ *  Copyright (C) 2007  Yoichi Yuasa <yuasa@linux-mips.org>
+ */
+#ifndef _ASM_IRQ_GT641XX_H
+#define _ASM_IRQ_GT641XX_H
+
+#ifndef GT641XX_IRQ_BASE
+#define GT641XX_IRQ_BASE		8
+#endif
+
+#define GT641XX_MEMORY_OUT_OF_RANGE_IRQ		(GT641XX_IRQ_BASE + 1)
+#define GT641XX_DMA_OUT_OF_RANGE_IRQ		(GT641XX_IRQ_BASE + 2)
+#define GT641XX_CPU_ACCESS_OUT_OF_RANGE_IRQ	(GT641XX_IRQ_BASE + 3)
+#define GT641XX_DMA0_IRQ			(GT641XX_IRQ_BASE + 4)
+#define GT641XX_DMA1_IRQ			(GT641XX_IRQ_BASE + 5)
+#define GT641XX_DMA2_IRQ			(GT641XX_IRQ_BASE + 6)
+#define GT641XX_DMA3_IRQ			(GT641XX_IRQ_BASE + 7)
+#define GT641XX_TIMER0_IRQ			(GT641XX_IRQ_BASE + 8)
+#define GT641XX_TIMER1_IRQ			(GT641XX_IRQ_BASE + 9)
+#define GT641XX_TIMER2_IRQ			(GT641XX_IRQ_BASE + 10)
+#define GT641XX_TIMER3_IRQ			(GT641XX_IRQ_BASE + 11)
+#define GT641XX_PCI_0_MASTER_READ_ERROR_IRQ	(GT641XX_IRQ_BASE + 12)
+#define GT641XX_PCI_0_SLAVE_WRITE_ERROR_IRQ	(GT641XX_IRQ_BASE + 13)
+#define GT641XX_PCI_0_MASTER_WRITE_ERROR_IRQ	(GT641XX_IRQ_BASE + 14)
+#define GT641XX_PCI_0_SLAVE_READ_ERROR_IRQ	(GT641XX_IRQ_BASE + 15)
+#define GT641XX_PCI_0_ADDRESS_ERROR_IRQ		(GT641XX_IRQ_BASE + 16)
+#define GT641XX_MEMORY_ERROR_IRQ		(GT641XX_IRQ_BASE + 17)
+#define GT641XX_PCI_0_MASTER_ABORT_IRQ		(GT641XX_IRQ_BASE + 18)
+#define GT641XX_PCI_0_TARGET_ABORT_IRQ		(GT641XX_IRQ_BASE + 19)
+#define GT641XX_PCI_0_RETRY_TIMEOUT_IRQ		(GT641XX_IRQ_BASE + 20)
+#define GT641XX_CPU_INT0_IRQ			(GT641XX_IRQ_BASE + 21)
+#define GT641XX_CPU_INT1_IRQ			(GT641XX_IRQ_BASE + 22)
+#define GT641XX_CPU_INT2_IRQ			(GT641XX_IRQ_BASE + 23)
+#define GT641XX_CPU_INT3_IRQ			(GT641XX_IRQ_BASE + 24)
+#define GT641XX_CPU_INT4_IRQ			(GT641XX_IRQ_BASE + 25)
+#define GT641XX_PCI_INT0_IRQ			(GT641XX_IRQ_BASE + 26)
+#define GT641XX_PCI_INT1_IRQ			(GT641XX_IRQ_BASE + 27)
+#define GT641XX_PCI_INT2_IRQ			(GT641XX_IRQ_BASE + 28)
+#define GT641XX_PCI_INT3_IRQ			(GT641XX_IRQ_BASE + 29)
+
+extern void gt641xx_irq_dispatch(void);
+extern void gt641xx_irq_init(void);
+
+#endif /* _ASM_IRQ_GT641XX_H */
diff --git a/arch/mips/include/asm/irq_regs.h b/arch/mips/include/asm/irq_regs.h
new file mode 100644
index 000000000..7795dc02c
--- /dev/null
+++ b/arch/mips/include/asm/irq_regs.h
@@ -0,0 +1,28 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ *
+ * Copyright (C) 2006 Ralf Baechle (ralf@linux-mips.org)
+ */
+#ifndef __ASM_IRQ_REGS_H
+#define __ASM_IRQ_REGS_H
+
+#define ARCH_HAS_OWN_IRQ_REGS
+
+#include <linux/thread_info.h>
+
+static inline struct pt_regs *get_irq_regs(void)
+{
+	return current_thread_info()->regs;
+}
+
+static inline struct pt_regs *set_irq_regs(struct pt_regs *new_regs)
+{
+	struct pt_regs *old_regs;
+
+	old_regs = get_irq_regs();
+	current_thread_info()->regs = new_regs;
+
+	return old_regs;
+}
+
+#endif /* __ASM_IRQ_REGS_H */
diff --git a/arch/mips/include/asm/irqflags.h b/arch/mips/include/asm/irqflags.h
new file mode 100644
index 000000000..f5b8300f4
--- /dev/null
+++ b/arch/mips/include/asm/irqflags.h
@@ -0,0 +1,185 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994, 95, 96, 97, 98, 99, 2003 by Ralf Baechle
+ * Copyright (C) 1996 by Paul M. Antoine
+ * Copyright (C) 1999 Silicon Graphics
+ * Copyright (C) 2000 MIPS Technologies, Inc.
+ */
+#ifndef _ASM_IRQFLAGS_H
+#define _ASM_IRQFLAGS_H
+
+#ifndef __ASSEMBLY__
+
+#include <linux/compiler.h>
+#include <linux/stringify.h>
+#include <asm/compiler.h>
+#include <asm/hazards.h>
+
+#if defined(CONFIG_CPU_HAS_DIEI)
+
+static inline void arch_local_irq_disable(void)
+{
+	__asm__ __volatile__(
+	"	.set	push						\n"
+	"	.set	noat						\n"
+	"	di							\n"
+	"	" __stringify(__irq_disable_hazard) "			\n"
+	"	.set	pop						\n"
+	: /* no outputs */
+	: /* no inputs */
+	: "memory");
+}
+
+static inline unsigned long arch_local_irq_save(void)
+{
+	unsigned long flags;
+
+	asm __volatile__(
+	"	.set	push						\n"
+	"	.set	reorder						\n"
+	"	.set	noat						\n"
+#if defined(CONFIG_CPU_LOONGSON64) || defined(CONFIG_CPU_LOONGSON32)
+	"	mfc0	%[flags], $12					\n"
+	"	di							\n"
+#else
+	"	di	%[flags]					\n"
+#endif
+	"	andi	%[flags], 1					\n"
+	"	" __stringify(__irq_disable_hazard) "			\n"
+	"	.set	pop						\n"
+	: [flags] "=r" (flags)
+	: /* no inputs */
+	: "memory");
+
+	return flags;
+}
+
+static inline void arch_local_irq_restore(unsigned long flags)
+{
+	unsigned long __tmp1;
+
+	__asm__ __volatile__(
+	"	.set	push						\n"
+	"	.set	noreorder					\n"
+	"	.set	noat						\n"
+#if defined(CONFIG_IRQ_MIPS_CPU)
+	/*
+	 * Slow, but doesn't suffer from a relatively unlikely race
+	 * condition we're having since days 1.
+	 */
+	"	beqz	%[flags], 1f					\n"
+	"	di							\n"
+	"	ei							\n"
+	"1:								\n"
+#else
+	/*
+	 * Fast, dangerous.  Life is fun, life is good.
+	 */
+	"	mfc0	$1, $12						\n"
+	"	ins	$1, %[flags], 0, 1				\n"
+	"	mtc0	$1, $12						\n"
+#endif
+	"	" __stringify(__irq_disable_hazard) "			\n"
+	"	.set	pop						\n"
+	: [flags] "=r" (__tmp1)
+	: "0" (flags)
+	: "memory");
+}
+
+#else
+/* Functions that require preempt_{dis,en}able() are in mips-atomic.c */
+void arch_local_irq_disable(void);
+unsigned long arch_local_irq_save(void);
+void arch_local_irq_restore(unsigned long flags);
+#endif /* CONFIG_CPU_HAS_DIEI */
+
+static inline void arch_local_irq_enable(void)
+{
+	__asm__ __volatile__(
+	"	.set	push						\n"
+	"	.set	reorder						\n"
+	"	.set	noat						\n"
+#if defined(CONFIG_CPU_HAS_DIEI)
+	"	ei							\n"
+#else
+	"	mfc0	$1,$12						\n"
+	"	ori	$1,0x1f						\n"
+	"	xori	$1,0x1e						\n"
+	"	mtc0	$1,$12						\n"
+#endif
+	"	" __stringify(__irq_enable_hazard) "			\n"
+	"	.set	pop						\n"
+	: /* no outputs */
+	: /* no inputs */
+	: "memory");
+}
+
+static inline unsigned long arch_local_save_flags(void)
+{
+	unsigned long flags;
+
+	asm __volatile__(
+	"	.set	push						\n"
+	"	.set	reorder						\n"
+	"	mfc0	%[flags], $12					\n"
+	"	.set	pop						\n"
+	: [flags] "=r" (flags));
+
+	return flags;
+}
+
+
+static inline int arch_irqs_disabled_flags(unsigned long flags)
+{
+	return !(flags & 1);
+}
+
+static inline int arch_irqs_disabled(void)
+{
+	return arch_irqs_disabled_flags(arch_local_save_flags());
+}
+
+#endif /* #ifndef __ASSEMBLY__ */
+
+/*
+ * Do the CPU's IRQ-state tracing from assembly code.
+ */
+#ifdef CONFIG_TRACE_IRQFLAGS
+/* Reload some registers clobbered by trace_hardirqs_on */
+#ifdef CONFIG_64BIT
+# define TRACE_IRQS_RELOAD_REGS						\
+	LONG_L	$11, PT_R11(sp);					\
+	LONG_L	$10, PT_R10(sp);					\
+	LONG_L	$9, PT_R9(sp);						\
+	LONG_L	$8, PT_R8(sp);						\
+	LONG_L	$7, PT_R7(sp);						\
+	LONG_L	$6, PT_R6(sp);						\
+	LONG_L	$5, PT_R5(sp);						\
+	LONG_L	$4, PT_R4(sp);						\
+	LONG_L	$2, PT_R2(sp)
+#else
+# define TRACE_IRQS_RELOAD_REGS						\
+	LONG_L	$7, PT_R7(sp);						\
+	LONG_L	$6, PT_R6(sp);						\
+	LONG_L	$5, PT_R5(sp);						\
+	LONG_L	$4, PT_R4(sp);						\
+	LONG_L	$2, PT_R2(sp)
+#endif
+# define TRACE_IRQS_ON							\
+	CLI;	/* make sure trace_hardirqs_on() is called in kernel level */ \
+	jal	trace_hardirqs_on
+# define TRACE_IRQS_ON_RELOAD						\
+	TRACE_IRQS_ON;							\
+	TRACE_IRQS_RELOAD_REGS
+# define TRACE_IRQS_OFF							\
+	jal	trace_hardirqs_off
+#else
+# define TRACE_IRQS_ON
+# define TRACE_IRQS_ON_RELOAD
+# define TRACE_IRQS_OFF
+#endif
+
+#endif /* _ASM_IRQFLAGS_H */
diff --git a/arch/mips/include/asm/isa-rev.h b/arch/mips/include/asm/isa-rev.h
new file mode 100644
index 000000000..683ea3454
--- /dev/null
+++ b/arch/mips/include/asm/isa-rev.h
@@ -0,0 +1,24 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2018 MIPS Tech, LLC
+ * Author: Matt Redfearn <matt.redfearn@mips.com>
+ */
+
+#ifndef __MIPS_ASM_ISA_REV_H__
+#define __MIPS_ASM_ISA_REV_H__
+
+/*
+ * The ISA revision level. This is 0 for MIPS I to V and N for
+ * MIPS{32,64}rN.
+ */
+
+/* If the compiler has defined __mips_isa_rev, believe it. */
+#ifdef __mips_isa_rev
+#define MIPS_ISA_REV __mips_isa_rev
+#else
+/* The compiler hasn't defined the isa rev so assume it's MIPS I - V (0) */
+#define MIPS_ISA_REV 0
+#endif
+
+
+#endif /* __MIPS_ASM_ISA_REV_H__ */
diff --git a/arch/mips/include/asm/isadep.h b/arch/mips/include/asm/isadep.h
new file mode 100644
index 000000000..8fc1e3ae8
--- /dev/null
+++ b/arch/mips/include/asm/isadep.h
@@ -0,0 +1,35 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Various ISA level dependent constants.
+ * Most of the following constants reflect the different layout
+ * of Coprocessor 0 registers.
+ *
+ * Copyright (c) 1998 Harald Koerfgen
+ */
+
+#ifndef __ASM_ISADEP_H
+#define __ASM_ISADEP_H
+
+#if defined(CONFIG_CPU_R3000)
+/*
+ * R2000 or R3000
+ */
+
+/*
+ * kernel or user mode? (CP0_STATUS)
+ */
+#define KU_MASK 0x08
+#define KU_USER 0x08
+#define KU_KERN 0x00
+
+#else
+/*
+ * kernel or user mode?
+ */
+#define KU_MASK 0x18
+#define KU_USER 0x10
+#define KU_KERN 0x00
+
+#endif
+
+#endif /* __ASM_ISADEP_H */
diff --git a/arch/mips/include/asm/jazz.h b/arch/mips/include/asm/jazz.h
new file mode 100644
index 000000000..a61970d01
--- /dev/null
+++ b/arch/mips/include/asm/jazz.h
@@ -0,0 +1,310 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995 - 1998 by Andreas Busse and Ralf Baechle
+ */
+#ifndef __ASM_JAZZ_H
+#define __ASM_JAZZ_H
+
+/*
+ * The addresses below are virtual address. The mappings are
+ * created on startup via wired entries in the tlb. The Mips
+ * Magnum R3000 and R4000 machines are similar in many aspects,
+ * but many hardware register are accessible at 0xb9000000 in
+ * instead of 0xe0000000.
+ */
+
+#define JAZZ_LOCAL_IO_SPACE	0xe0000000
+
+/*
+ * Revision numbers in PICA_ASIC_REVISION
+ *
+ * 0xf0000000 - Rev1
+ * 0xf0000001 - Rev2
+ * 0xf0000002 - Rev3
+ */
+#define PICA_ASIC_REVISION	0xe0000008
+
+/*
+ * The segments of the seven segment LED are mapped
+ * to the control bits as follows:
+ *
+ *	   (7)
+ *	---------
+ *	|	|
+ *  (2) |	| (6)
+ *	|  (1)	|
+ *	---------
+ *	|	|
+ *  (3) |	| (5)
+ *	|  (4)	|
+ *	--------- . (0)
+ */
+#define PICA_LED		0xe000f000
+
+/*
+ * Some characters for the LED control registers
+ * The original Mips machines seem to have a LED display
+ * with integrated decoder while the Acer machines can
+ * control each of the seven segments and the dot independently.
+ * It's only a toy, anyway...
+ */
+#define LED_DOT			0x01
+#define LED_SPACE		0x00
+#define LED_0			0xfc
+#define LED_1			0x60
+#define LED_2			0xda
+#define LED_3			0xf2
+#define LED_4			0x66
+#define LED_5			0xb6
+#define LED_6			0xbe
+#define LED_7			0xe0
+#define LED_8			0xfe
+#define LED_9			0xf6
+#define LED_A			0xee
+#define LED_b			0x3e
+#define LED_C			0x9c
+#define LED_d			0x7a
+#define LED_E			0x9e
+#define LED_F			0x8e
+
+#ifndef __ASSEMBLY__
+
+static __inline__ void pica_set_led(unsigned int bits)
+{
+	volatile unsigned int *led_register = (unsigned int *) PICA_LED;
+
+	*led_register = bits;
+}
+
+#endif /* !__ASSEMBLY__ */
+
+/*
+ * Base address of the Sonic Ethernet adapter in Jazz machines.
+ */
+#define JAZZ_ETHERNET_BASE  0xe0001000
+
+/*
+ * Base address of the 53C94 SCSI hostadapter in Jazz machines.
+ */
+#define JAZZ_SCSI_BASE		0xe0002000
+
+/*
+ * i8042 keyboard controller for JAZZ and PICA chipsets.
+ * This address is just a guess and seems to differ from
+ * other mips machines such as RC3xxx...
+ */
+#define JAZZ_KEYBOARD_ADDRESS	0xe0005000
+#define JAZZ_KEYBOARD_DATA	0xe0005000
+#define JAZZ_KEYBOARD_COMMAND	0xe0005001
+
+#ifndef __ASSEMBLY__
+
+typedef struct {
+	unsigned char data;
+	unsigned char command;
+} jazz_keyboard_hardware;
+
+#define jazz_kh ((keyboard_hardware *) JAZZ_KEYBOARD_ADDRESS)
+
+typedef struct {
+	unsigned char pad0[3];
+	unsigned char data;
+	unsigned char pad1[3];
+	unsigned char command;
+} mips_keyboard_hardware;
+
+/*
+ * For now. Needs to be changed for RC3xxx support. See below.
+ */
+#define keyboard_hardware	jazz_keyboard_hardware
+
+#endif /* !__ASSEMBLY__ */
+
+/*
+ * i8042 keyboard controller for most other Mips machines.
+ */
+#define MIPS_KEYBOARD_ADDRESS	0xb9005000
+#define MIPS_KEYBOARD_DATA	0xb9005003
+#define MIPS_KEYBOARD_COMMAND	0xb9005007
+
+/*
+ * Serial and parallel ports (WD 16C552) on the Mips JAZZ
+ */
+#define JAZZ_SERIAL1_BASE	(unsigned int)0xe0006000
+#define JAZZ_SERIAL2_BASE	(unsigned int)0xe0007000
+#define JAZZ_PARALLEL_BASE	(unsigned int)0xe0008000
+
+/*
+ * Dummy Device Address. Used in jazzdma.c
+ */
+#define JAZZ_DUMMY_DEVICE	0xe000d000
+
+/*
+ * JAZZ timer registers and interrupt no.
+ * Note that the hardware timer interrupt is actually on
+ * cpu level 6, but to keep compatibility with PC stuff
+ * it is remapped to vector 0. See arch/mips/kernel/entry.S.
+ */
+#define JAZZ_TIMER_INTERVAL	0xe0000228
+#define JAZZ_TIMER_REGISTER	0xe0000230
+
+/*
+ * DRAM configuration register
+ */
+#ifndef __ASSEMBLY__
+#ifdef __MIPSEL__
+typedef struct {
+	unsigned int bank2 : 3;
+	unsigned int bank1 : 3;
+	unsigned int mem_bus_width : 1;
+	unsigned int reserved2 : 1;
+	unsigned int page_mode : 1;
+	unsigned int reserved1 : 23;
+} dram_configuration;
+#else /* defined (__MIPSEB__) */
+typedef struct {
+	unsigned int reserved1 : 23;
+	unsigned int page_mode : 1;
+	unsigned int reserved2 : 1;
+	unsigned int mem_bus_width : 1;
+	unsigned int bank1 : 3;
+	unsigned int bank2 : 3;
+} dram_configuration;
+#endif
+#endif /* !__ASSEMBLY__ */
+
+#define PICA_DRAM_CONFIG	0xe00fffe0
+
+/*
+ * JAZZ interrupt control registers
+ */
+#define JAZZ_IO_IRQ_SOURCE	0xe0010000
+#define JAZZ_IO_IRQ_ENABLE	0xe0010002
+
+/*
+ * JAZZ Interrupt Level definitions
+ *
+ * This is somewhat broken.  For reasons which nobody can remember anymore
+ * we remap the Jazz interrupts to the usual ISA style interrupt numbers.
+ */
+#define JAZZ_IRQ_START		24
+#define JAZZ_IRQ_END		(24 + 9)
+#define JAZZ_PARALLEL_IRQ	(JAZZ_IRQ_START + 0)
+#define JAZZ_FLOPPY_IRQ		(JAZZ_IRQ_START + 1)
+#define JAZZ_SOUND_IRQ		(JAZZ_IRQ_START + 2)
+#define JAZZ_VIDEO_IRQ		(JAZZ_IRQ_START + 3)
+#define JAZZ_ETHERNET_IRQ	(JAZZ_IRQ_START + 4)
+#define JAZZ_SCSI_IRQ		(JAZZ_IRQ_START + 5)
+#define JAZZ_KEYBOARD_IRQ	(JAZZ_IRQ_START + 6)
+#define JAZZ_MOUSE_IRQ		(JAZZ_IRQ_START + 7)
+#define JAZZ_SERIAL1_IRQ	(JAZZ_IRQ_START + 8)
+#define JAZZ_SERIAL2_IRQ	(JAZZ_IRQ_START + 9)
+
+#define JAZZ_TIMER_IRQ		(MIPS_CPU_IRQ_BASE+6)
+
+
+/*
+ * JAZZ DMA Channels
+ * Note: Channels 4...7 are not used with respect to the Acer PICA-61
+ * chipset which does not provide these DMA channels.
+ */
+#define JAZZ_SCSI_DMA		0	       /* SCSI */
+#define JAZZ_FLOPPY_DMA		1	       /* FLOPPY */
+#define JAZZ_AUDIOL_DMA		2	       /* AUDIO L */
+#define JAZZ_AUDIOR_DMA		3	       /* AUDIO R */
+
+/*
+ * JAZZ R4030 MCT_ADR chip (DMA controller)
+ * Note: Virtual Addresses !
+ */
+#define JAZZ_R4030_CONFIG	0xE0000000	/* R4030 config register */
+#define JAZZ_R4030_REVISION	0xE0000008	/* same as PICA_ASIC_REVISION */
+#define JAZZ_R4030_INV_ADDR	0xE0000010	/* Invalid Address register */
+
+#define JAZZ_R4030_TRSTBL_BASE	0xE0000018	/* Translation Table Base */
+#define JAZZ_R4030_TRSTBL_LIM	0xE0000020	/* Translation Table Limit */
+#define JAZZ_R4030_TRSTBL_INV	0xE0000028	/* Translation Table Invalidate */
+
+#define JAZZ_R4030_CACHE_MTNC	0xE0000030	/* Cache Maintenance */
+#define JAZZ_R4030_R_FAIL_ADDR	0xE0000038	/* Remote Failed Address */
+#define JAZZ_R4030_M_FAIL_ADDR	0xE0000040	/* Memory Failed Address */
+
+#define JAZZ_R4030_CACHE_PTAG	0xE0000048	/* I/O Cache Physical Tag */
+#define JAZZ_R4030_CACHE_LTAG	0xE0000050	/* I/O Cache Logical Tag */
+#define JAZZ_R4030_CACHE_BMASK	0xE0000058	/* I/O Cache Byte Mask */
+#define JAZZ_R4030_CACHE_BWIN	0xE0000060	/* I/O Cache Buffer Window */
+
+/*
+ * Remote Speed Registers.
+ *
+ *  0: free,	  1: Ethernet,	2: SCSI,      3: Floppy,
+ *  4: RTC,	  5: Kb./Mouse	6: serial 1,  7: serial 2,
+ *  8: parallel,  9: NVRAM,    10: CPU,	     11: PROM,
+ * 12: reserved, 13: free,     14: 7seg LED, 15: ???
+ */
+#define JAZZ_R4030_REM_SPEED	0xE0000070	/* 16 Remote Speed Registers */
+						/* 0xE0000070,78,80... 0xE00000E8 */
+#define JAZZ_R4030_IRQ_ENABLE	0xE00000E8	/* Internal Interrupt Enable */
+#define JAZZ_R4030_INVAL_ADDR	0xE0000010	/* Invalid address Register */
+#define JAZZ_R4030_IRQ_SOURCE	0xE0000200	/* Interrupt Source Register */
+#define JAZZ_R4030_I386_ERROR	0xE0000208	/* i386/EISA Bus Error */
+
+/*
+ * Virtual (E)ISA controller address
+ */
+#define JAZZ_EISA_IRQ_ACK	0xE0000238	/* EISA interrupt acknowledge */
+
+/*
+ * Access the R4030 DMA and I/O Controller
+ */
+#ifndef __ASSEMBLY__
+
+static inline void r4030_delay(void)
+{
+__asm__ __volatile__(
+	".set\tnoreorder\n\t"
+	"nop\n\t"
+	"nop\n\t"
+	"nop\n\t"
+	"nop\n\t"
+	".set\treorder");
+}
+
+static inline unsigned short r4030_read_reg16(unsigned long addr)
+{
+	unsigned short ret = *((volatile unsigned short *)addr);
+	r4030_delay();
+	return ret;
+}
+
+static inline unsigned int r4030_read_reg32(unsigned long addr)
+{
+	unsigned int ret = *((volatile unsigned int *)addr);
+	r4030_delay();
+	return ret;
+}
+
+static inline void r4030_write_reg16(unsigned long addr, unsigned val)
+{
+	*((volatile unsigned short *)addr) = val;
+	r4030_delay();
+}
+
+static inline void r4030_write_reg32(unsigned long addr, unsigned val)
+{
+	*((volatile unsigned int *)addr) = val;
+	r4030_delay();
+}
+
+#endif /* !__ASSEMBLY__ */
+
+#define JAZZ_FDC_BASE	0xe0003000
+#define JAZZ_RTC_BASE	0xe0004000
+#define JAZZ_PORT_BASE	0xe2000000
+
+#define JAZZ_EISA_BASE	0xe3000000
+
+#endif /* __ASM_JAZZ_H */
diff --git a/arch/mips/include/asm/jazzdma.h b/arch/mips/include/asm/jazzdma.h
new file mode 100644
index 000000000..c831da7fa
--- /dev/null
+++ b/arch/mips/include/asm/jazzdma.h
@@ -0,0 +1,88 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Helpfile for jazzdma.c -- Mips Jazz R4030 DMA controller support
+ */
+#ifndef _ASM_JAZZDMA_H
+#define _ASM_JAZZDMA_H
+
+/*
+ * Prototypes and macros
+ */
+extern unsigned long vdma_alloc(unsigned long paddr, unsigned long size);
+extern int vdma_free(unsigned long laddr);
+extern unsigned long vdma_phys2log(unsigned long paddr);
+extern unsigned long vdma_log2phys(unsigned long laddr);
+extern void vdma_stats(void);		/* for debugging only */
+
+extern void vdma_enable(int channel);
+extern void vdma_disable(int channel);
+extern void vdma_set_mode(int channel, int mode);
+extern void vdma_set_addr(int channel, long addr);
+extern void vdma_set_count(int channel, int count);
+extern int vdma_get_residue(int channel);
+extern int vdma_get_enable(int channel);
+
+/*
+ * some definitions used by the driver functions
+ */
+#define VDMA_PAGESIZE		4096
+#define VDMA_PGTBL_ENTRIES	4096
+#define VDMA_PGTBL_SIZE		(sizeof(VDMA_PGTBL_ENTRY) * VDMA_PGTBL_ENTRIES)
+#define VDMA_PAGE_EMPTY		0xff000000
+
+/*
+ * Macros to get page no. and offset of a given address
+ * Note that VDMA_PAGE() works for physical addresses only
+ */
+#define VDMA_PAGE(a)		((unsigned int)(a) >> 12)
+#define VDMA_OFFSET(a)		((unsigned int)(a) & (VDMA_PAGESIZE-1))
+
+/*
+ * VDMA pagetable entry description
+ */
+typedef volatile struct VDMA_PGTBL_ENTRY {
+	unsigned int frame;		/* physical frame no. */
+	unsigned int owner;		/* owner of this entry (0=free) */
+} VDMA_PGTBL_ENTRY;
+
+
+/*
+ * DMA channel control registers
+ * in the R4030 MCT_ADR chip
+ */
+#define JAZZ_R4030_CHNL_MODE	0xE0000100	/* 8 DMA Channel Mode Registers, */
+						/* 0xE0000100,120,140... */
+#define JAZZ_R4030_CHNL_ENABLE	0xE0000108	/* 8 DMA Channel Enable Regs, */
+						/* 0xE0000108,128,148... */
+#define JAZZ_R4030_CHNL_COUNT	0xE0000110	/* 8 DMA Channel Byte Cnt Regs, */
+						/* 0xE0000110,130,150... */
+#define JAZZ_R4030_CHNL_ADDR	0xE0000118	/* 8 DMA Channel Address Regs, */
+						/* 0xE0000118,138,158... */
+
+/* channel enable register bits */
+
+#define R4030_CHNL_ENABLE	 (1<<0)
+#define R4030_CHNL_WRITE	 (1<<1)
+#define R4030_TC_INTR		 (1<<8)
+#define R4030_MEM_INTR		 (1<<9)
+#define R4030_ADDR_INTR		 (1<<10)
+
+/*
+ * Channel mode register bits
+ */
+#define R4030_MODE_ATIME_40	 (0) /* device access time on remote bus */
+#define R4030_MODE_ATIME_80	 (1)
+#define R4030_MODE_ATIME_120	 (2)
+#define R4030_MODE_ATIME_160	 (3)
+#define R4030_MODE_ATIME_200	 (4)
+#define R4030_MODE_ATIME_240	 (5)
+#define R4030_MODE_ATIME_280	 (6)
+#define R4030_MODE_ATIME_320	 (7)
+#define R4030_MODE_WIDTH_8	 (1<<3) /* device data bus width */
+#define R4030_MODE_WIDTH_16	 (2<<3)
+#define R4030_MODE_WIDTH_32	 (3<<3)
+#define R4030_MODE_INTR_EN	 (1<<5)
+#define R4030_MODE_BURST	 (1<<6) /* Rev. 2 only */
+#define R4030_MODE_FAST_ACK	 (1<<7) /* Rev. 2 only */
+
+#endif /* _ASM_JAZZDMA_H */
diff --git a/arch/mips/include/asm/jump_label.h b/arch/mips/include/asm/jump_label.h
new file mode 100644
index 000000000..c5c6864e6
--- /dev/null
+++ b/arch/mips/include/asm/jump_label.h
@@ -0,0 +1,77 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (c) 2010 Cavium Networks, Inc.
+ */
+#ifndef _ASM_MIPS_JUMP_LABEL_H
+#define _ASM_MIPS_JUMP_LABEL_H
+
+#define arch_jump_label_transform_static arch_jump_label_transform
+
+#ifndef __ASSEMBLY__
+
+#include <linux/types.h>
+#include <asm/isa-rev.h>
+
+#define JUMP_LABEL_NOP_SIZE 4
+
+#ifdef CONFIG_64BIT
+#define WORD_INSN ".dword"
+#else
+#define WORD_INSN ".word"
+#endif
+
+#ifdef CONFIG_CPU_MICROMIPS
+# define B_INSN "b32"
+# define J_INSN "j32"
+#elif MIPS_ISA_REV >= 6
+# define B_INSN "bc"
+# define J_INSN "bc"
+#else
+# define B_INSN "b"
+# define J_INSN "j"
+#endif
+
+static __always_inline bool arch_static_branch(struct static_key *key, bool branch)
+{
+	asm_volatile_goto("1:\t" B_INSN " 2f\n\t"
+		"2:\t.insn\n\t"
+		".pushsection __jump_table,  \"aw\"\n\t"
+		WORD_INSN " 1b, %l[l_yes], %0\n\t"
+		".popsection\n\t"
+		: :  "i" (&((char *)key)[branch]) : : l_yes);
+
+	return false;
+l_yes:
+	return true;
+}
+
+static __always_inline bool arch_static_branch_jump(struct static_key *key, bool branch)
+{
+	asm_volatile_goto("1:\t" J_INSN " %l[l_yes]\n\t"
+		".pushsection __jump_table,  \"aw\"\n\t"
+		WORD_INSN " 1b, %l[l_yes], %0\n\t"
+		".popsection\n\t"
+		: :  "i" (&((char *)key)[branch]) : : l_yes);
+
+	return false;
+l_yes:
+	return true;
+}
+
+#ifdef CONFIG_64BIT
+typedef u64 jump_label_t;
+#else
+typedef u32 jump_label_t;
+#endif
+
+struct jump_entry {
+	jump_label_t code;
+	jump_label_t target;
+	jump_label_t key;
+};
+
+#endif  /* __ASSEMBLY__ */
+#endif /* _ASM_MIPS_JUMP_LABEL_H */
diff --git a/arch/mips/include/asm/kdebug.h b/arch/mips/include/asm/kdebug.h
new file mode 100644
index 000000000..a55a207cf
--- /dev/null
+++ b/arch/mips/include/asm/kdebug.h
@@ -0,0 +1,20 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _ASM_MIPS_KDEBUG_H
+#define _ASM_MIPS_KDEBUG_H
+
+#include <linux/notifier.h>
+
+enum die_val {
+	DIE_OOPS = 1,
+	DIE_FP,
+	DIE_TRAP,
+	DIE_RI,
+	DIE_PAGE_FAULT,
+	DIE_BREAK,
+	DIE_SSTEPBP,
+	DIE_MSAFP,
+	DIE_UPROBE,
+	DIE_UPROBE_XOL,
+};
+
+#endif /* _ASM_MIPS_KDEBUG_H */
diff --git a/arch/mips/include/asm/kexec.h b/arch/mips/include/asm/kexec.h
new file mode 100644
index 000000000..d6d5fa5cc
--- /dev/null
+++ b/arch/mips/include/asm/kexec.h
@@ -0,0 +1,51 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * kexec.h for kexec
+ * Created by <nschichan@corp.free.fr> on Thu Oct 12 14:59:34 2006
+ */
+
+#ifndef _MIPS_KEXEC
+# define _MIPS_KEXEC
+
+#include <asm/stacktrace.h>
+
+/* Maximum physical address we can use pages from */
+#define KEXEC_SOURCE_MEMORY_LIMIT (-1UL)
+/* Maximum address we can reach in physical address mode */
+#define KEXEC_DESTINATION_MEMORY_LIMIT (-1UL)
+ /* Maximum address we can use for the control code buffer */
+#define KEXEC_CONTROL_MEMORY_LIMIT (-1UL)
+/* Reserve 3*4096 bytes for board-specific info */
+#define KEXEC_CONTROL_PAGE_SIZE (4096 + 3*4096)
+
+/* The native architecture */
+#define KEXEC_ARCH KEXEC_ARCH_MIPS
+#define MAX_NOTE_BYTES 1024
+
+static inline void crash_setup_regs(struct pt_regs *newregs,
+				    struct pt_regs *oldregs)
+{
+	if (oldregs)
+		memcpy(newregs, oldregs, sizeof(*newregs));
+	else
+		prepare_frametrace(newregs);
+}
+
+#ifdef CONFIG_KEXEC
+struct kimage;
+extern unsigned long kexec_args[4];
+extern int (*_machine_kexec_prepare)(struct kimage *);
+extern void (*_machine_kexec_shutdown)(void);
+extern void (*_machine_crash_shutdown)(struct pt_regs *regs);
+void default_machine_crash_shutdown(struct pt_regs *regs);
+void kexec_nonboot_cpu_jump(void);
+void kexec_reboot(void);
+#ifdef CONFIG_SMP
+extern const unsigned char kexec_smp_wait[];
+extern unsigned long secondary_kexec_args[4];
+extern atomic_t kexec_ready_to_reboot;
+extern void (*_crash_smp_send_stop)(void);
+#endif
+#endif
+
+#endif /* !_MIPS_KEXEC */
diff --git a/arch/mips/include/asm/kgdb.h b/arch/mips/include/asm/kgdb.h
new file mode 100644
index 000000000..b4e210d63
--- /dev/null
+++ b/arch/mips/include/asm/kgdb.h
@@ -0,0 +1,45 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_KGDB_H_
+#define __ASM_KGDB_H_
+
+#ifdef __KERNEL__
+
+#include <asm/sgidefs.h>
+
+#if (_MIPS_ISA == _MIPS_ISA_MIPS1) || (_MIPS_ISA == _MIPS_ISA_MIPS2) || \
+	(_MIPS_ISA == _MIPS_ISA_MIPS32)
+
+#define KGDB_GDB_REG_SIZE	32
+#define GDB_SIZEOF_REG		sizeof(u32)
+
+#elif (_MIPS_ISA == _MIPS_ISA_MIPS3) || (_MIPS_ISA == _MIPS_ISA_MIPS4) || \
+	(_MIPS_ISA == _MIPS_ISA_MIPS64)
+
+#ifdef CONFIG_32BIT
+#define KGDB_GDB_REG_SIZE	32
+#define GDB_SIZEOF_REG		sizeof(u32)
+#else /* CONFIG_32BIT */
+#define KGDB_GDB_REG_SIZE	64
+#define GDB_SIZEOF_REG		sizeof(u64)
+#endif
+#else
+#error "Need to set KGDB_GDB_REG_SIZE for MIPS ISA"
+#endif /* _MIPS_ISA */
+
+#define BUFMAX			2048
+#define DBG_MAX_REG_NUM		72
+#define NUMREGBYTES		(DBG_MAX_REG_NUM * sizeof(GDB_SIZEOF_REG))
+#define NUMCRITREGBYTES		(12 * sizeof(GDB_SIZEOF_REG))
+#define BREAK_INSTR_SIZE	4
+#define CACHE_FLUSH_IS_SAFE	0
+
+extern void arch_kgdb_breakpoint(void);
+extern void *saved_vectors[32];
+extern void handle_exception(struct pt_regs *regs);
+extern void breakinst(void);
+extern int kgdb_ll_trap(int cmd, const char *str,
+			struct pt_regs *regs, long err, int trap, int sig);
+
+#endif				/* __KERNEL__ */
+
+#endif /* __ASM_KGDB_H_ */
diff --git a/arch/mips/include/asm/kprobes.h b/arch/mips/include/asm/kprobes.h
new file mode 100644
index 000000000..68b1e5d45
--- /dev/null
+++ b/arch/mips/include/asm/kprobes.h
@@ -0,0 +1,78 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *  Kernel Probes (KProbes)
+ *  include/asm-mips/kprobes.h
+ *
+ *  Copyright 2006 Sony Corp.
+ *  Copyright 2010 Cavium Networks
+ */
+
+#ifndef _ASM_KPROBES_H
+#define _ASM_KPROBES_H
+
+#include <asm-generic/kprobes.h>
+
+#ifdef CONFIG_KPROBES
+#include <linux/ptrace.h>
+#include <linux/types.h>
+
+#include <asm/cacheflush.h>
+#include <asm/kdebug.h>
+#include <asm/inst.h>
+
+#define	 __ARCH_WANT_KPROBES_INSN_SLOT
+
+struct kprobe;
+struct pt_regs;
+
+typedef union mips_instruction kprobe_opcode_t;
+
+#define MAX_INSN_SIZE 2
+
+#define flush_insn_slot(p)						\
+do {									\
+	if (p->addr)							\
+		flush_icache_range((unsigned long)p->addr,		\
+			   (unsigned long)p->addr +			\
+			   (MAX_INSN_SIZE * sizeof(kprobe_opcode_t)));	\
+} while (0)
+
+
+#define kretprobe_blacklist_size 0
+
+void arch_remove_kprobe(struct kprobe *p);
+int kprobe_fault_handler(struct pt_regs *regs, int trapnr);
+
+/* Architecture specific copy of original instruction*/
+struct arch_specific_insn {
+	/* copy of the original instruction */
+	kprobe_opcode_t *insn;
+};
+
+struct prev_kprobe {
+	struct kprobe *kp;
+	unsigned long status;
+	unsigned long old_SR;
+	unsigned long saved_SR;
+	unsigned long saved_epc;
+};
+
+#define SKIP_DELAYSLOT 0x0001
+
+/* per-cpu kprobe control block */
+struct kprobe_ctlblk {
+	unsigned long kprobe_status;
+	unsigned long kprobe_old_SR;
+	unsigned long kprobe_saved_SR;
+	unsigned long kprobe_saved_epc;
+	/* Per-thread fields, used while emulating branches */
+	unsigned long flags;
+	unsigned long target_epc;
+	struct prev_kprobe prev_kprobe;
+};
+
+extern int kprobe_exceptions_notify(struct notifier_block *self,
+				    unsigned long val, void *data);
+
+#endif /* CONFIG_KPROBES */
+#endif /* _ASM_KPROBES_H */
diff --git a/arch/mips/include/asm/kvm_host.h b/arch/mips/include/asm/kvm_host.h
new file mode 100644
index 000000000..8042a87b8
--- /dev/null
+++ b/arch/mips/include/asm/kvm_host.h
@@ -0,0 +1,903 @@
+/*
+* This file is subject to the terms and conditions of the GNU General Public
+* License.  See the file "COPYING" in the main directory of this archive
+* for more details.
+*
+* Copyright (C) 2012  MIPS Technologies, Inc.  All rights reserved.
+* Authors: Sanjay Lal <sanjayl@kymasys.com>
+*/
+
+#ifndef __MIPS_KVM_HOST_H__
+#define __MIPS_KVM_HOST_H__
+
+#include <linux/cpumask.h>
+#include <linux/mutex.h>
+#include <linux/hrtimer.h>
+#include <linux/interrupt.h>
+#include <linux/types.h>
+#include <linux/kvm.h>
+#include <linux/kvm_types.h>
+#include <linux/threads.h>
+#include <linux/spinlock.h>
+
+#include <asm/asm.h>
+#include <asm/inst.h>
+#include <asm/mipsregs.h>
+
+#include <kvm/iodev.h>
+
+/* MIPS KVM register ids */
+#define MIPS_CP0_32(_R, _S)					\
+	(KVM_REG_MIPS_CP0 | KVM_REG_SIZE_U32 | (8 * (_R) + (_S)))
+
+#define MIPS_CP0_64(_R, _S)					\
+	(KVM_REG_MIPS_CP0 | KVM_REG_SIZE_U64 | (8 * (_R) + (_S)))
+
+#define KVM_REG_MIPS_CP0_INDEX		MIPS_CP0_32(0, 0)
+#define KVM_REG_MIPS_CP0_ENTRYLO0	MIPS_CP0_64(2, 0)
+#define KVM_REG_MIPS_CP0_ENTRYLO1	MIPS_CP0_64(3, 0)
+#define KVM_REG_MIPS_CP0_CONTEXT	MIPS_CP0_64(4, 0)
+#define KVM_REG_MIPS_CP0_CONTEXTCONFIG	MIPS_CP0_32(4, 1)
+#define KVM_REG_MIPS_CP0_USERLOCAL	MIPS_CP0_64(4, 2)
+#define KVM_REG_MIPS_CP0_XCONTEXTCONFIG	MIPS_CP0_64(4, 3)
+#define KVM_REG_MIPS_CP0_PAGEMASK	MIPS_CP0_32(5, 0)
+#define KVM_REG_MIPS_CP0_PAGEGRAIN	MIPS_CP0_32(5, 1)
+#define KVM_REG_MIPS_CP0_SEGCTL0	MIPS_CP0_64(5, 2)
+#define KVM_REG_MIPS_CP0_SEGCTL1	MIPS_CP0_64(5, 3)
+#define KVM_REG_MIPS_CP0_SEGCTL2	MIPS_CP0_64(5, 4)
+#define KVM_REG_MIPS_CP0_PWBASE		MIPS_CP0_64(5, 5)
+#define KVM_REG_MIPS_CP0_PWFIELD	MIPS_CP0_64(5, 6)
+#define KVM_REG_MIPS_CP0_PWSIZE		MIPS_CP0_64(5, 7)
+#define KVM_REG_MIPS_CP0_WIRED		MIPS_CP0_32(6, 0)
+#define KVM_REG_MIPS_CP0_PWCTL		MIPS_CP0_32(6, 6)
+#define KVM_REG_MIPS_CP0_HWRENA		MIPS_CP0_32(7, 0)
+#define KVM_REG_MIPS_CP0_BADVADDR	MIPS_CP0_64(8, 0)
+#define KVM_REG_MIPS_CP0_BADINSTR	MIPS_CP0_32(8, 1)
+#define KVM_REG_MIPS_CP0_BADINSTRP	MIPS_CP0_32(8, 2)
+#define KVM_REG_MIPS_CP0_COUNT		MIPS_CP0_32(9, 0)
+#define KVM_REG_MIPS_CP0_ENTRYHI	MIPS_CP0_64(10, 0)
+#define KVM_REG_MIPS_CP0_COMPARE	MIPS_CP0_32(11, 0)
+#define KVM_REG_MIPS_CP0_STATUS		MIPS_CP0_32(12, 0)
+#define KVM_REG_MIPS_CP0_INTCTL		MIPS_CP0_32(12, 1)
+#define KVM_REG_MIPS_CP0_CAUSE		MIPS_CP0_32(13, 0)
+#define KVM_REG_MIPS_CP0_EPC		MIPS_CP0_64(14, 0)
+#define KVM_REG_MIPS_CP0_PRID		MIPS_CP0_32(15, 0)
+#define KVM_REG_MIPS_CP0_EBASE		MIPS_CP0_64(15, 1)
+#define KVM_REG_MIPS_CP0_CONFIG		MIPS_CP0_32(16, 0)
+#define KVM_REG_MIPS_CP0_CONFIG1	MIPS_CP0_32(16, 1)
+#define KVM_REG_MIPS_CP0_CONFIG2	MIPS_CP0_32(16, 2)
+#define KVM_REG_MIPS_CP0_CONFIG3	MIPS_CP0_32(16, 3)
+#define KVM_REG_MIPS_CP0_CONFIG4	MIPS_CP0_32(16, 4)
+#define KVM_REG_MIPS_CP0_CONFIG5	MIPS_CP0_32(16, 5)
+#define KVM_REG_MIPS_CP0_CONFIG6	MIPS_CP0_32(16, 6)
+#define KVM_REG_MIPS_CP0_CONFIG7	MIPS_CP0_32(16, 7)
+#define KVM_REG_MIPS_CP0_MAARI		MIPS_CP0_64(17, 2)
+#define KVM_REG_MIPS_CP0_XCONTEXT	MIPS_CP0_64(20, 0)
+#define KVM_REG_MIPS_CP0_DIAG		MIPS_CP0_32(22, 0)
+#define KVM_REG_MIPS_CP0_ERROREPC	MIPS_CP0_64(30, 0)
+#define KVM_REG_MIPS_CP0_KSCRATCH1	MIPS_CP0_64(31, 2)
+#define KVM_REG_MIPS_CP0_KSCRATCH2	MIPS_CP0_64(31, 3)
+#define KVM_REG_MIPS_CP0_KSCRATCH3	MIPS_CP0_64(31, 4)
+#define KVM_REG_MIPS_CP0_KSCRATCH4	MIPS_CP0_64(31, 5)
+#define KVM_REG_MIPS_CP0_KSCRATCH5	MIPS_CP0_64(31, 6)
+#define KVM_REG_MIPS_CP0_KSCRATCH6	MIPS_CP0_64(31, 7)
+
+
+#define KVM_MAX_VCPUS		16
+
+#define KVM_HALT_POLL_NS_DEFAULT 500000
+
+extern unsigned long GUESTID_MASK;
+extern unsigned long GUESTID_FIRST_VERSION;
+extern unsigned long GUESTID_VERSION_MASK;
+
+#define KVM_INVALID_ADDR		0xdeadbeef
+
+/*
+ * EVA has overlapping user & kernel address spaces, so user VAs may be >
+ * PAGE_OFFSET. For this reason we can't use the default KVM_HVA_ERR_BAD of
+ * PAGE_OFFSET.
+ */
+
+#define KVM_HVA_ERR_BAD			(-1UL)
+#define KVM_HVA_ERR_RO_BAD		(-2UL)
+
+static inline bool kvm_is_error_hva(unsigned long addr)
+{
+	return IS_ERR_VALUE(addr);
+}
+
+struct kvm_vm_stat {
+	struct kvm_vm_stat_generic generic;
+};
+
+struct kvm_vcpu_stat {
+	struct kvm_vcpu_stat_generic generic;
+	u64 wait_exits;
+	u64 cache_exits;
+	u64 signal_exits;
+	u64 int_exits;
+	u64 cop_unusable_exits;
+	u64 tlbmod_exits;
+	u64 tlbmiss_ld_exits;
+	u64 tlbmiss_st_exits;
+	u64 addrerr_st_exits;
+	u64 addrerr_ld_exits;
+	u64 syscall_exits;
+	u64 resvd_inst_exits;
+	u64 break_inst_exits;
+	u64 trap_inst_exits;
+	u64 msa_fpe_exits;
+	u64 fpe_exits;
+	u64 msa_disabled_exits;
+	u64 flush_dcache_exits;
+	u64 vz_gpsi_exits;
+	u64 vz_gsfc_exits;
+	u64 vz_hc_exits;
+	u64 vz_grr_exits;
+	u64 vz_gva_exits;
+	u64 vz_ghfc_exits;
+	u64 vz_gpa_exits;
+	u64 vz_resvd_exits;
+#ifdef CONFIG_CPU_LOONGSON64
+	u64 vz_cpucfg_exits;
+#endif
+};
+
+struct kvm_arch_memory_slot {
+};
+
+#ifdef CONFIG_CPU_LOONGSON64
+struct ipi_state {
+	uint32_t status;
+	uint32_t en;
+	uint32_t set;
+	uint32_t clear;
+	uint64_t buf[4];
+};
+
+struct loongson_kvm_ipi;
+
+struct ipi_io_device {
+	int node_id;
+	struct loongson_kvm_ipi *ipi;
+	struct kvm_io_device device;
+};
+
+struct loongson_kvm_ipi {
+	spinlock_t lock;
+	struct kvm *kvm;
+	struct ipi_state ipistate[16];
+	struct ipi_io_device dev_ipi[4];
+};
+#endif
+
+struct kvm_arch {
+	/* Guest physical mm */
+	struct mm_struct gpa_mm;
+	/* Mask of CPUs needing GPA ASID flush */
+	cpumask_t asid_flush_mask;
+#ifdef CONFIG_CPU_LOONGSON64
+	struct loongson_kvm_ipi ipi;
+#endif
+};
+
+#define N_MIPS_COPROC_REGS	32
+#define N_MIPS_COPROC_SEL	8
+
+struct mips_coproc {
+	unsigned long reg[N_MIPS_COPROC_REGS][N_MIPS_COPROC_SEL];
+#ifdef CONFIG_KVM_MIPS_DEBUG_COP0_COUNTERS
+	unsigned long stat[N_MIPS_COPROC_REGS][N_MIPS_COPROC_SEL];
+#endif
+};
+
+/*
+ * Coprocessor 0 register names
+ */
+#define MIPS_CP0_TLB_INDEX	0
+#define MIPS_CP0_TLB_RANDOM	1
+#define MIPS_CP0_TLB_LOW	2
+#define MIPS_CP0_TLB_LO0	2
+#define MIPS_CP0_TLB_LO1	3
+#define MIPS_CP0_TLB_CONTEXT	4
+#define MIPS_CP0_TLB_PG_MASK	5
+#define MIPS_CP0_TLB_WIRED	6
+#define MIPS_CP0_HWRENA		7
+#define MIPS_CP0_BAD_VADDR	8
+#define MIPS_CP0_COUNT		9
+#define MIPS_CP0_TLB_HI		10
+#define MIPS_CP0_COMPARE	11
+#define MIPS_CP0_STATUS		12
+#define MIPS_CP0_CAUSE		13
+#define MIPS_CP0_EXC_PC		14
+#define MIPS_CP0_PRID		15
+#define MIPS_CP0_CONFIG		16
+#define MIPS_CP0_LLADDR		17
+#define MIPS_CP0_WATCH_LO	18
+#define MIPS_CP0_WATCH_HI	19
+#define MIPS_CP0_TLB_XCONTEXT	20
+#define MIPS_CP0_DIAG		22
+#define MIPS_CP0_ECC		26
+#define MIPS_CP0_CACHE_ERR	27
+#define MIPS_CP0_TAG_LO		28
+#define MIPS_CP0_TAG_HI		29
+#define MIPS_CP0_ERROR_PC	30
+#define MIPS_CP0_DEBUG		23
+#define MIPS_CP0_DEPC		24
+#define MIPS_CP0_PERFCNT	25
+#define MIPS_CP0_ERRCTL		26
+#define MIPS_CP0_DATA_LO	28
+#define MIPS_CP0_DATA_HI	29
+#define MIPS_CP0_DESAVE		31
+
+#define MIPS_CP0_CONFIG_SEL	0
+#define MIPS_CP0_CONFIG1_SEL	1
+#define MIPS_CP0_CONFIG2_SEL	2
+#define MIPS_CP0_CONFIG3_SEL	3
+#define MIPS_CP0_CONFIG4_SEL	4
+#define MIPS_CP0_CONFIG5_SEL	5
+
+#define MIPS_CP0_GUESTCTL2	10
+#define MIPS_CP0_GUESTCTL2_SEL	5
+#define MIPS_CP0_GTOFFSET	12
+#define MIPS_CP0_GTOFFSET_SEL	7
+
+/* Resume Flags */
+#define RESUME_FLAG_DR		(1<<0)	/* Reload guest nonvolatile state? */
+#define RESUME_FLAG_HOST	(1<<1)	/* Resume host? */
+
+#define RESUME_GUEST		0
+#define RESUME_GUEST_DR		RESUME_FLAG_DR
+#define RESUME_HOST		RESUME_FLAG_HOST
+
+enum emulation_result {
+	EMULATE_DONE,		/* no further processing */
+	EMULATE_DO_MMIO,	/* kvm_run filled with MMIO request */
+	EMULATE_FAIL,		/* can't emulate this instruction */
+	EMULATE_WAIT,		/* WAIT instruction */
+	EMULATE_PRIV_FAIL,
+	EMULATE_EXCEPT,		/* A guest exception has been generated */
+	EMULATE_HYPERCALL,	/* HYPCALL instruction */
+};
+
+#if defined(CONFIG_64BIT)
+#define VPN2_MASK		GENMASK(cpu_vmbits - 1, 13)
+#else
+#define VPN2_MASK		0xffffe000
+#endif
+#define KVM_ENTRYHI_ASID	cpu_asid_mask(&boot_cpu_data)
+#define TLB_IS_GLOBAL(x)	((x).tlb_lo[0] & (x).tlb_lo[1] & ENTRYLO_G)
+#define TLB_VPN2(x)		((x).tlb_hi & VPN2_MASK)
+#define TLB_ASID(x)		((x).tlb_hi & KVM_ENTRYHI_ASID)
+#define TLB_LO_IDX(x, va)	(((va) >> PAGE_SHIFT) & 1)
+#define TLB_IS_VALID(x, va)	((x).tlb_lo[TLB_LO_IDX(x, va)] & ENTRYLO_V)
+#define TLB_IS_DIRTY(x, va)	((x).tlb_lo[TLB_LO_IDX(x, va)] & ENTRYLO_D)
+#define TLB_HI_VPN2_HIT(x, y)	((TLB_VPN2(x) & ~(x).tlb_mask) ==	\
+				 ((y) & VPN2_MASK & ~(x).tlb_mask))
+#define TLB_HI_ASID_HIT(x, y)	(TLB_IS_GLOBAL(x) ||			\
+				 TLB_ASID(x) == ((y) & KVM_ENTRYHI_ASID))
+
+struct kvm_mips_tlb {
+	long tlb_mask;
+	long tlb_hi;
+	long tlb_lo[2];
+};
+
+#define KVM_MIPS_AUX_FPU	0x1
+#define KVM_MIPS_AUX_MSA	0x2
+
+struct kvm_vcpu_arch {
+	void *guest_ebase;
+	int (*vcpu_run)(struct kvm_vcpu *vcpu);
+
+	/* Host registers preserved across guest mode execution */
+	unsigned long host_stack;
+	unsigned long host_gp;
+	unsigned long host_pgd;
+	unsigned long host_entryhi;
+
+	/* Host CP0 registers used when handling exits from guest */
+	unsigned long host_cp0_badvaddr;
+	unsigned long host_cp0_epc;
+	u32 host_cp0_cause;
+	u32 host_cp0_guestctl0;
+	u32 host_cp0_badinstr;
+	u32 host_cp0_badinstrp;
+
+	/* GPRS */
+	unsigned long gprs[32];
+	unsigned long hi;
+	unsigned long lo;
+	unsigned long pc;
+
+	/* FPU State */
+	struct mips_fpu_struct fpu;
+	/* Which auxiliary state is loaded (KVM_MIPS_AUX_*) */
+	unsigned int aux_inuse;
+
+	/* COP0 State */
+	struct mips_coproc cop0;
+
+	/* Resume PC after MMIO completion */
+	unsigned long io_pc;
+	/* GPR used as IO source/target */
+	u32 io_gpr;
+
+	struct hrtimer comparecount_timer;
+	/* Count timer control KVM register */
+	u32 count_ctl;
+	/* Count bias from the raw time */
+	u32 count_bias;
+	/* Frequency of timer in Hz */
+	u32 count_hz;
+	/* Dynamic nanosecond bias (multiple of count_period) to avoid overflow */
+	s64 count_dyn_bias;
+	/* Resume time */
+	ktime_t count_resume;
+	/* Period of timer tick in ns */
+	u64 count_period;
+
+	/* Bitmask of exceptions that are pending */
+	unsigned long pending_exceptions;
+
+	/* Bitmask of pending exceptions to be cleared */
+	unsigned long pending_exceptions_clr;
+
+	/* Cache some mmu pages needed inside spinlock regions */
+	struct kvm_mmu_memory_cache mmu_page_cache;
+
+	/* vcpu's vzguestid is different on each host cpu in an smp system */
+	u32 vzguestid[NR_CPUS];
+
+	/* wired guest TLB entries */
+	struct kvm_mips_tlb *wired_tlb;
+	unsigned int wired_tlb_limit;
+	unsigned int wired_tlb_used;
+
+	/* emulated guest MAAR registers */
+	unsigned long maar[6];
+
+	/* Last CPU the VCPU state was loaded on */
+	int last_sched_cpu;
+	/* Last CPU the VCPU actually executed guest code on */
+	int last_exec_cpu;
+
+	/* WAIT executed */
+	int wait;
+
+	u8 fpu_enabled;
+	u8 msa_enabled;
+};
+
+static inline void _kvm_atomic_set_c0_guest_reg(unsigned long *reg,
+						unsigned long val)
+{
+	unsigned long temp;
+	do {
+		__asm__ __volatile__(
+		"	.set	push				\n"
+		"	.set	"MIPS_ISA_ARCH_LEVEL"		\n"
+		"	"__stringify(LONG_LL)	" %0, %1	\n"
+		"	or	%0, %2				\n"
+		"	"__stringify(LONG_SC)	" %0, %1	\n"
+		"	.set	pop				\n"
+		: "=&r" (temp), "+m" (*reg)
+		: "r" (val));
+	} while (unlikely(!temp));
+}
+
+static inline void _kvm_atomic_clear_c0_guest_reg(unsigned long *reg,
+						  unsigned long val)
+{
+	unsigned long temp;
+	do {
+		__asm__ __volatile__(
+		"	.set	push				\n"
+		"	.set	"MIPS_ISA_ARCH_LEVEL"		\n"
+		"	"__stringify(LONG_LL)	" %0, %1	\n"
+		"	and	%0, %2				\n"
+		"	"__stringify(LONG_SC)	" %0, %1	\n"
+		"	.set	pop				\n"
+		: "=&r" (temp), "+m" (*reg)
+		: "r" (~val));
+	} while (unlikely(!temp));
+}
+
+static inline void _kvm_atomic_change_c0_guest_reg(unsigned long *reg,
+						   unsigned long change,
+						   unsigned long val)
+{
+	unsigned long temp;
+	do {
+		__asm__ __volatile__(
+		"	.set	push				\n"
+		"	.set	"MIPS_ISA_ARCH_LEVEL"		\n"
+		"	"__stringify(LONG_LL)	" %0, %1	\n"
+		"	and	%0, %2				\n"
+		"	or	%0, %3				\n"
+		"	"__stringify(LONG_SC)	" %0, %1	\n"
+		"	.set	pop				\n"
+		: "=&r" (temp), "+m" (*reg)
+		: "r" (~change), "r" (val & change));
+	} while (unlikely(!temp));
+}
+
+/* Guest register types, used in accessor build below */
+#define __KVMT32	u32
+#define __KVMTl	unsigned long
+
+/*
+ * __BUILD_KVM_$ops_SAVED(): kvm_$op_sw_gc0_$reg()
+ * These operate on the saved guest C0 state in RAM.
+ */
+
+/* Generate saved context simple accessors */
+#define __BUILD_KVM_RW_SAVED(name, type, _reg, sel)			\
+static inline __KVMT##type kvm_read_sw_gc0_##name(struct mips_coproc *cop0) \
+{									\
+	return cop0->reg[(_reg)][(sel)];				\
+}									\
+static inline void kvm_write_sw_gc0_##name(struct mips_coproc *cop0,	\
+					   __KVMT##type val)		\
+{									\
+	cop0->reg[(_reg)][(sel)] = val;					\
+}
+
+/* Generate saved context bitwise modifiers */
+#define __BUILD_KVM_SET_SAVED(name, type, _reg, sel)			\
+static inline void kvm_set_sw_gc0_##name(struct mips_coproc *cop0,	\
+					 __KVMT##type val)		\
+{									\
+	cop0->reg[(_reg)][(sel)] |= val;				\
+}									\
+static inline void kvm_clear_sw_gc0_##name(struct mips_coproc *cop0,	\
+					   __KVMT##type val)		\
+{									\
+	cop0->reg[(_reg)][(sel)] &= ~val;				\
+}									\
+static inline void kvm_change_sw_gc0_##name(struct mips_coproc *cop0,	\
+					    __KVMT##type mask,		\
+					    __KVMT##type val)		\
+{									\
+	unsigned long _mask = mask;					\
+	cop0->reg[(_reg)][(sel)] &= ~_mask;				\
+	cop0->reg[(_reg)][(sel)] |= val & _mask;			\
+}
+
+/* Generate saved context atomic bitwise modifiers */
+#define __BUILD_KVM_ATOMIC_SAVED(name, type, _reg, sel)			\
+static inline void kvm_set_sw_gc0_##name(struct mips_coproc *cop0,	\
+					 __KVMT##type val)		\
+{									\
+	_kvm_atomic_set_c0_guest_reg(&cop0->reg[(_reg)][(sel)], val);	\
+}									\
+static inline void kvm_clear_sw_gc0_##name(struct mips_coproc *cop0,	\
+					   __KVMT##type val)		\
+{									\
+	_kvm_atomic_clear_c0_guest_reg(&cop0->reg[(_reg)][(sel)], val);	\
+}									\
+static inline void kvm_change_sw_gc0_##name(struct mips_coproc *cop0,	\
+					    __KVMT##type mask,		\
+					    __KVMT##type val)		\
+{									\
+	_kvm_atomic_change_c0_guest_reg(&cop0->reg[(_reg)][(sel)], mask, \
+					val);				\
+}
+
+/*
+ * __BUILD_KVM_$ops_VZ(): kvm_$op_vz_gc0_$reg()
+ * These operate on the VZ guest C0 context in hardware.
+ */
+
+/* Generate VZ guest context simple accessors */
+#define __BUILD_KVM_RW_VZ(name, type, _reg, sel)			\
+static inline __KVMT##type kvm_read_vz_gc0_##name(struct mips_coproc *cop0) \
+{									\
+	return read_gc0_##name();					\
+}									\
+static inline void kvm_write_vz_gc0_##name(struct mips_coproc *cop0,	\
+					   __KVMT##type val)		\
+{									\
+	write_gc0_##name(val);						\
+}
+
+/* Generate VZ guest context bitwise modifiers */
+#define __BUILD_KVM_SET_VZ(name, type, _reg, sel)			\
+static inline void kvm_set_vz_gc0_##name(struct mips_coproc *cop0,	\
+					 __KVMT##type val)		\
+{									\
+	set_gc0_##name(val);						\
+}									\
+static inline void kvm_clear_vz_gc0_##name(struct mips_coproc *cop0,	\
+					   __KVMT##type val)		\
+{									\
+	clear_gc0_##name(val);						\
+}									\
+static inline void kvm_change_vz_gc0_##name(struct mips_coproc *cop0,	\
+					    __KVMT##type mask,		\
+					    __KVMT##type val)		\
+{									\
+	change_gc0_##name(mask, val);					\
+}
+
+/* Generate VZ guest context save/restore to/from saved context */
+#define __BUILD_KVM_SAVE_VZ(name, _reg, sel)			\
+static inline void kvm_restore_gc0_##name(struct mips_coproc *cop0)	\
+{									\
+	write_gc0_##name(cop0->reg[(_reg)][(sel)]);			\
+}									\
+static inline void kvm_save_gc0_##name(struct mips_coproc *cop0)	\
+{									\
+	cop0->reg[(_reg)][(sel)] = read_gc0_##name();			\
+}
+
+/*
+ * __BUILD_KVM_$ops_WRAP(): kvm_$op_$name1() -> kvm_$op_$name2()
+ * These wrap a set of operations to provide them with a different name.
+ */
+
+/* Generate simple accessor wrapper */
+#define __BUILD_KVM_RW_WRAP(name1, name2, type)				\
+static inline __KVMT##type kvm_read_##name1(struct mips_coproc *cop0)	\
+{									\
+	return kvm_read_##name2(cop0);					\
+}									\
+static inline void kvm_write_##name1(struct mips_coproc *cop0,		\
+				     __KVMT##type val)			\
+{									\
+	kvm_write_##name2(cop0, val);					\
+}
+
+/* Generate bitwise modifier wrapper */
+#define __BUILD_KVM_SET_WRAP(name1, name2, type)			\
+static inline void kvm_set_##name1(struct mips_coproc *cop0,		\
+				   __KVMT##type val)			\
+{									\
+	kvm_set_##name2(cop0, val);					\
+}									\
+static inline void kvm_clear_##name1(struct mips_coproc *cop0,		\
+				     __KVMT##type val)			\
+{									\
+	kvm_clear_##name2(cop0, val);					\
+}									\
+static inline void kvm_change_##name1(struct mips_coproc *cop0,		\
+				      __KVMT##type mask,		\
+				      __KVMT##type val)			\
+{									\
+	kvm_change_##name2(cop0, mask, val);				\
+}
+
+/*
+ * __BUILD_KVM_$ops_SW(): kvm_$op_c0_guest_$reg() -> kvm_$op_sw_gc0_$reg()
+ * These generate accessors operating on the saved context in RAM, and wrap them
+ * with the common guest C0 accessors (for use by common emulation code).
+ */
+
+#define __BUILD_KVM_RW_SW(name, type, _reg, sel)			\
+	__BUILD_KVM_RW_SAVED(name, type, _reg, sel)			\
+	__BUILD_KVM_RW_WRAP(c0_guest_##name, sw_gc0_##name, type)
+
+#define __BUILD_KVM_SET_SW(name, type, _reg, sel)			\
+	__BUILD_KVM_SET_SAVED(name, type, _reg, sel)			\
+	__BUILD_KVM_SET_WRAP(c0_guest_##name, sw_gc0_##name, type)
+
+#define __BUILD_KVM_ATOMIC_SW(name, type, _reg, sel)			\
+	__BUILD_KVM_ATOMIC_SAVED(name, type, _reg, sel)			\
+	__BUILD_KVM_SET_WRAP(c0_guest_##name, sw_gc0_##name, type)
+
+/*
+ * VZ (hardware assisted virtualisation)
+ * These macros use the active guest state in VZ mode (hardware registers),
+ */
+
+/*
+ * __BUILD_KVM_$ops_HW(): kvm_$op_c0_guest_$reg() -> kvm_$op_vz_gc0_$reg()
+ * These generate accessors operating on the VZ guest context in hardware, and
+ * wrap them with the common guest C0 accessors (for use by common emulation
+ * code).
+ *
+ * Accessors operating on the saved context in RAM are also generated to allow
+ * convenient explicit saving and restoring of the state.
+ */
+
+#define __BUILD_KVM_RW_HW(name, type, _reg, sel)			\
+	__BUILD_KVM_RW_SAVED(name, type, _reg, sel)			\
+	__BUILD_KVM_RW_VZ(name, type, _reg, sel)			\
+	__BUILD_KVM_RW_WRAP(c0_guest_##name, vz_gc0_##name, type)	\
+	__BUILD_KVM_SAVE_VZ(name, _reg, sel)
+
+#define __BUILD_KVM_SET_HW(name, type, _reg, sel)			\
+	__BUILD_KVM_SET_SAVED(name, type, _reg, sel)			\
+	__BUILD_KVM_SET_VZ(name, type, _reg, sel)			\
+	__BUILD_KVM_SET_WRAP(c0_guest_##name, vz_gc0_##name, type)
+
+/*
+ * We can't do atomic modifications of COP0 state if hardware can modify it.
+ * Races must be handled explicitly.
+ */
+#define __BUILD_KVM_ATOMIC_HW	__BUILD_KVM_SET_HW
+
+/*
+ * Define accessors for CP0 registers that are accessible to the guest. These
+ * are primarily used by common emulation code, which may need to access the
+ * registers differently depending on the implementation.
+ *
+ *    fns_hw/sw    name     type    reg num         select
+ */
+__BUILD_KVM_RW_HW(index,          32, MIPS_CP0_TLB_INDEX,    0)
+__BUILD_KVM_RW_HW(entrylo0,       l,  MIPS_CP0_TLB_LO0,      0)
+__BUILD_KVM_RW_HW(entrylo1,       l,  MIPS_CP0_TLB_LO1,      0)
+__BUILD_KVM_RW_HW(context,        l,  MIPS_CP0_TLB_CONTEXT,  0)
+__BUILD_KVM_RW_HW(contextconfig,  32, MIPS_CP0_TLB_CONTEXT,  1)
+__BUILD_KVM_RW_HW(userlocal,      l,  MIPS_CP0_TLB_CONTEXT,  2)
+__BUILD_KVM_RW_HW(xcontextconfig, l,  MIPS_CP0_TLB_CONTEXT,  3)
+__BUILD_KVM_RW_HW(pagemask,       l,  MIPS_CP0_TLB_PG_MASK,  0)
+__BUILD_KVM_RW_HW(pagegrain,      32, MIPS_CP0_TLB_PG_MASK,  1)
+__BUILD_KVM_RW_HW(segctl0,        l,  MIPS_CP0_TLB_PG_MASK,  2)
+__BUILD_KVM_RW_HW(segctl1,        l,  MIPS_CP0_TLB_PG_MASK,  3)
+__BUILD_KVM_RW_HW(segctl2,        l,  MIPS_CP0_TLB_PG_MASK,  4)
+__BUILD_KVM_RW_HW(pwbase,         l,  MIPS_CP0_TLB_PG_MASK,  5)
+__BUILD_KVM_RW_HW(pwfield,        l,  MIPS_CP0_TLB_PG_MASK,  6)
+__BUILD_KVM_RW_HW(pwsize,         l,  MIPS_CP0_TLB_PG_MASK,  7)
+__BUILD_KVM_RW_HW(wired,          32, MIPS_CP0_TLB_WIRED,    0)
+__BUILD_KVM_RW_HW(pwctl,          32, MIPS_CP0_TLB_WIRED,    6)
+__BUILD_KVM_RW_HW(hwrena,         32, MIPS_CP0_HWRENA,       0)
+__BUILD_KVM_RW_HW(badvaddr,       l,  MIPS_CP0_BAD_VADDR,    0)
+__BUILD_KVM_RW_HW(badinstr,       32, MIPS_CP0_BAD_VADDR,    1)
+__BUILD_KVM_RW_HW(badinstrp,      32, MIPS_CP0_BAD_VADDR,    2)
+__BUILD_KVM_RW_SW(count,          32, MIPS_CP0_COUNT,        0)
+__BUILD_KVM_RW_HW(entryhi,        l,  MIPS_CP0_TLB_HI,       0)
+__BUILD_KVM_RW_HW(compare,        32, MIPS_CP0_COMPARE,      0)
+__BUILD_KVM_RW_HW(status,         32, MIPS_CP0_STATUS,       0)
+__BUILD_KVM_RW_HW(intctl,         32, MIPS_CP0_STATUS,       1)
+__BUILD_KVM_RW_HW(cause,          32, MIPS_CP0_CAUSE,        0)
+__BUILD_KVM_RW_HW(epc,            l,  MIPS_CP0_EXC_PC,       0)
+__BUILD_KVM_RW_SW(prid,           32, MIPS_CP0_PRID,         0)
+__BUILD_KVM_RW_HW(ebase,          l,  MIPS_CP0_PRID,         1)
+__BUILD_KVM_RW_HW(config,         32, MIPS_CP0_CONFIG,       0)
+__BUILD_KVM_RW_HW(config1,        32, MIPS_CP0_CONFIG,       1)
+__BUILD_KVM_RW_HW(config2,        32, MIPS_CP0_CONFIG,       2)
+__BUILD_KVM_RW_HW(config3,        32, MIPS_CP0_CONFIG,       3)
+__BUILD_KVM_RW_HW(config4,        32, MIPS_CP0_CONFIG,       4)
+__BUILD_KVM_RW_HW(config5,        32, MIPS_CP0_CONFIG,       5)
+__BUILD_KVM_RW_HW(config6,        32, MIPS_CP0_CONFIG,       6)
+__BUILD_KVM_RW_HW(config7,        32, MIPS_CP0_CONFIG,       7)
+__BUILD_KVM_RW_SW(maari,          l,  MIPS_CP0_LLADDR,       2)
+__BUILD_KVM_RW_HW(xcontext,       l,  MIPS_CP0_TLB_XCONTEXT, 0)
+__BUILD_KVM_RW_HW(errorepc,       l,  MIPS_CP0_ERROR_PC,     0)
+__BUILD_KVM_RW_HW(kscratch1,      l,  MIPS_CP0_DESAVE,       2)
+__BUILD_KVM_RW_HW(kscratch2,      l,  MIPS_CP0_DESAVE,       3)
+__BUILD_KVM_RW_HW(kscratch3,      l,  MIPS_CP0_DESAVE,       4)
+__BUILD_KVM_RW_HW(kscratch4,      l,  MIPS_CP0_DESAVE,       5)
+__BUILD_KVM_RW_HW(kscratch5,      l,  MIPS_CP0_DESAVE,       6)
+__BUILD_KVM_RW_HW(kscratch6,      l,  MIPS_CP0_DESAVE,       7)
+
+/* Bitwise operations (on HW state) */
+__BUILD_KVM_SET_HW(status,        32, MIPS_CP0_STATUS,       0)
+/* Cause can be modified asynchronously from hardirq hrtimer callback */
+__BUILD_KVM_ATOMIC_HW(cause,      32, MIPS_CP0_CAUSE,        0)
+__BUILD_KVM_SET_HW(ebase,         l,  MIPS_CP0_PRID,         1)
+
+/* Bitwise operations (on saved state) */
+__BUILD_KVM_SET_SAVED(config,     32, MIPS_CP0_CONFIG,       0)
+__BUILD_KVM_SET_SAVED(config1,    32, MIPS_CP0_CONFIG,       1)
+__BUILD_KVM_SET_SAVED(config2,    32, MIPS_CP0_CONFIG,       2)
+__BUILD_KVM_SET_SAVED(config3,    32, MIPS_CP0_CONFIG,       3)
+__BUILD_KVM_SET_SAVED(config4,    32, MIPS_CP0_CONFIG,       4)
+__BUILD_KVM_SET_SAVED(config5,    32, MIPS_CP0_CONFIG,       5)
+
+/* Helpers */
+
+static inline bool kvm_mips_guest_can_have_fpu(struct kvm_vcpu_arch *vcpu)
+{
+	return (!__builtin_constant_p(raw_cpu_has_fpu) || raw_cpu_has_fpu) &&
+		vcpu->fpu_enabled;
+}
+
+static inline bool kvm_mips_guest_has_fpu(struct kvm_vcpu_arch *vcpu)
+{
+	return kvm_mips_guest_can_have_fpu(vcpu) &&
+		kvm_read_c0_guest_config1(&vcpu->cop0) & MIPS_CONF1_FP;
+}
+
+static inline bool kvm_mips_guest_can_have_msa(struct kvm_vcpu_arch *vcpu)
+{
+	return (!__builtin_constant_p(cpu_has_msa) || cpu_has_msa) &&
+		vcpu->msa_enabled;
+}
+
+static inline bool kvm_mips_guest_has_msa(struct kvm_vcpu_arch *vcpu)
+{
+	return kvm_mips_guest_can_have_msa(vcpu) &&
+		kvm_read_c0_guest_config3(&vcpu->cop0) & MIPS_CONF3_MSA;
+}
+
+struct kvm_mips_callbacks {
+	int (*handle_cop_unusable)(struct kvm_vcpu *vcpu);
+	int (*handle_tlb_mod)(struct kvm_vcpu *vcpu);
+	int (*handle_tlb_ld_miss)(struct kvm_vcpu *vcpu);
+	int (*handle_tlb_st_miss)(struct kvm_vcpu *vcpu);
+	int (*handle_addr_err_st)(struct kvm_vcpu *vcpu);
+	int (*handle_addr_err_ld)(struct kvm_vcpu *vcpu);
+	int (*handle_syscall)(struct kvm_vcpu *vcpu);
+	int (*handle_res_inst)(struct kvm_vcpu *vcpu);
+	int (*handle_break)(struct kvm_vcpu *vcpu);
+	int (*handle_trap)(struct kvm_vcpu *vcpu);
+	int (*handle_msa_fpe)(struct kvm_vcpu *vcpu);
+	int (*handle_fpe)(struct kvm_vcpu *vcpu);
+	int (*handle_msa_disabled)(struct kvm_vcpu *vcpu);
+	int (*handle_guest_exit)(struct kvm_vcpu *vcpu);
+	int (*hardware_enable)(void);
+	void (*hardware_disable)(void);
+	int (*check_extension)(struct kvm *kvm, long ext);
+	int (*vcpu_init)(struct kvm_vcpu *vcpu);
+	void (*vcpu_uninit)(struct kvm_vcpu *vcpu);
+	int (*vcpu_setup)(struct kvm_vcpu *vcpu);
+	void (*prepare_flush_shadow)(struct kvm *kvm);
+	gpa_t (*gva_to_gpa)(gva_t gva);
+	void (*queue_timer_int)(struct kvm_vcpu *vcpu);
+	void (*dequeue_timer_int)(struct kvm_vcpu *vcpu);
+	void (*queue_io_int)(struct kvm_vcpu *vcpu,
+			     struct kvm_mips_interrupt *irq);
+	void (*dequeue_io_int)(struct kvm_vcpu *vcpu,
+			       struct kvm_mips_interrupt *irq);
+	int (*irq_deliver)(struct kvm_vcpu *vcpu, unsigned int priority,
+			   u32 cause);
+	int (*irq_clear)(struct kvm_vcpu *vcpu, unsigned int priority,
+			 u32 cause);
+	unsigned long (*num_regs)(struct kvm_vcpu *vcpu);
+	int (*copy_reg_indices)(struct kvm_vcpu *vcpu, u64 __user *indices);
+	int (*get_one_reg)(struct kvm_vcpu *vcpu,
+			   const struct kvm_one_reg *reg, s64 *v);
+	int (*set_one_reg)(struct kvm_vcpu *vcpu,
+			   const struct kvm_one_reg *reg, s64 v);
+	int (*vcpu_load)(struct kvm_vcpu *vcpu, int cpu);
+	int (*vcpu_put)(struct kvm_vcpu *vcpu, int cpu);
+	int (*vcpu_run)(struct kvm_vcpu *vcpu);
+	void (*vcpu_reenter)(struct kvm_vcpu *vcpu);
+};
+extern struct kvm_mips_callbacks *kvm_mips_callbacks;
+int kvm_mips_emulation_init(struct kvm_mips_callbacks **install_callbacks);
+
+/* Debug: dump vcpu state */
+int kvm_arch_vcpu_dump_regs(struct kvm_vcpu *vcpu);
+
+extern int kvm_mips_handle_exit(struct kvm_vcpu *vcpu);
+
+/* Building of entry/exception code */
+int kvm_mips_entry_setup(void);
+void *kvm_mips_build_vcpu_run(void *addr);
+void *kvm_mips_build_tlb_refill_exception(void *addr, void *handler);
+void *kvm_mips_build_exception(void *addr, void *handler);
+void *kvm_mips_build_exit(void *addr);
+
+/* FPU/MSA context management */
+void __kvm_save_fpu(struct kvm_vcpu_arch *vcpu);
+void __kvm_restore_fpu(struct kvm_vcpu_arch *vcpu);
+void __kvm_restore_fcsr(struct kvm_vcpu_arch *vcpu);
+void __kvm_save_msa(struct kvm_vcpu_arch *vcpu);
+void __kvm_restore_msa(struct kvm_vcpu_arch *vcpu);
+void __kvm_restore_msa_upper(struct kvm_vcpu_arch *vcpu);
+void __kvm_restore_msacsr(struct kvm_vcpu_arch *vcpu);
+void kvm_own_fpu(struct kvm_vcpu *vcpu);
+void kvm_own_msa(struct kvm_vcpu *vcpu);
+void kvm_drop_fpu(struct kvm_vcpu *vcpu);
+void kvm_lose_fpu(struct kvm_vcpu *vcpu);
+
+/* TLB handling */
+int kvm_mips_handle_vz_root_tlb_fault(unsigned long badvaddr,
+				      struct kvm_vcpu *vcpu, bool write_fault);
+
+int kvm_vz_host_tlb_inv(struct kvm_vcpu *vcpu, unsigned long entryhi);
+int kvm_vz_guest_tlb_lookup(struct kvm_vcpu *vcpu, unsigned long gva,
+			    unsigned long *gpa);
+void kvm_vz_local_flush_roottlb_all_guests(void);
+void kvm_vz_local_flush_guesttlb_all(void);
+void kvm_vz_save_guesttlb(struct kvm_mips_tlb *buf, unsigned int index,
+			  unsigned int count);
+void kvm_vz_load_guesttlb(const struct kvm_mips_tlb *buf, unsigned int index,
+			  unsigned int count);
+#ifdef CONFIG_CPU_LOONGSON64
+void kvm_loongson_clear_guest_vtlb(void);
+void kvm_loongson_clear_guest_ftlb(void);
+#endif
+
+/* MMU handling */
+
+bool kvm_mips_flush_gpa_pt(struct kvm *kvm, gfn_t start_gfn, gfn_t end_gfn);
+int kvm_mips_mkclean_gpa_pt(struct kvm *kvm, gfn_t start_gfn, gfn_t end_gfn);
+pgd_t *kvm_pgd_alloc(void);
+void kvm_mmu_free_memory_caches(struct kvm_vcpu *vcpu);
+
+#define KVM_ARCH_WANT_MMU_NOTIFIER
+
+/* Emulation */
+enum emulation_result update_pc(struct kvm_vcpu *vcpu, u32 cause);
+int kvm_get_badinstr(u32 *opc, struct kvm_vcpu *vcpu, u32 *out);
+int kvm_get_badinstrp(u32 *opc, struct kvm_vcpu *vcpu, u32 *out);
+
+/**
+ * kvm_is_ifetch_fault() - Find whether a TLBL exception is due to ifetch fault.
+ * @vcpu:	Virtual CPU.
+ *
+ * Returns:	Whether the TLBL exception was likely due to an instruction
+ *		fetch fault rather than a data load fault.
+ */
+static inline bool kvm_is_ifetch_fault(struct kvm_vcpu_arch *vcpu)
+{
+	unsigned long badvaddr = vcpu->host_cp0_badvaddr;
+	unsigned long epc = msk_isa16_mode(vcpu->pc);
+	u32 cause = vcpu->host_cp0_cause;
+
+	if (epc == badvaddr)
+		return true;
+
+	/*
+	 * Branches may be 32-bit or 16-bit instructions.
+	 * This isn't exact, but we don't really support MIPS16 or microMIPS yet
+	 * in KVM anyway.
+	 */
+	if ((cause & CAUSEF_BD) && badvaddr - epc <= 4)
+		return true;
+
+	return false;
+}
+
+extern enum emulation_result kvm_mips_complete_mmio_load(struct kvm_vcpu *vcpu);
+
+u32 kvm_mips_read_count(struct kvm_vcpu *vcpu);
+void kvm_mips_write_count(struct kvm_vcpu *vcpu, u32 count);
+void kvm_mips_write_compare(struct kvm_vcpu *vcpu, u32 compare, bool ack);
+void kvm_mips_init_count(struct kvm_vcpu *vcpu, unsigned long count_hz);
+int kvm_mips_set_count_ctl(struct kvm_vcpu *vcpu, s64 count_ctl);
+int kvm_mips_set_count_resume(struct kvm_vcpu *vcpu, s64 count_resume);
+int kvm_mips_set_count_hz(struct kvm_vcpu *vcpu, s64 count_hz);
+void kvm_mips_count_enable_cause(struct kvm_vcpu *vcpu);
+void kvm_mips_count_disable_cause(struct kvm_vcpu *vcpu);
+enum hrtimer_restart kvm_mips_count_timeout(struct kvm_vcpu *vcpu);
+
+/* fairly internal functions requiring some care to use */
+int kvm_mips_count_disabled(struct kvm_vcpu *vcpu);
+ktime_t kvm_mips_freeze_hrtimer(struct kvm_vcpu *vcpu, u32 *count);
+int kvm_mips_restore_hrtimer(struct kvm_vcpu *vcpu, ktime_t before,
+			     u32 count, int min_drift);
+
+void kvm_vz_acquire_htimer(struct kvm_vcpu *vcpu);
+void kvm_vz_lose_htimer(struct kvm_vcpu *vcpu);
+
+enum emulation_result kvm_mips_emulate_store(union mips_instruction inst,
+					     u32 cause,
+					     struct kvm_vcpu *vcpu);
+enum emulation_result kvm_mips_emulate_load(union mips_instruction inst,
+					    u32 cause,
+					    struct kvm_vcpu *vcpu);
+
+/* COP0 */
+enum emulation_result kvm_mips_emul_wait(struct kvm_vcpu *vcpu);
+
+/* Hypercalls (hypcall.c) */
+
+enum emulation_result kvm_mips_emul_hypcall(struct kvm_vcpu *vcpu,
+					    union mips_instruction inst);
+int kvm_mips_handle_hypcall(struct kvm_vcpu *vcpu);
+
+/* Misc */
+extern void kvm_mips_dump_stats(struct kvm_vcpu *vcpu);
+extern unsigned long kvm_mips_get_ramsize(struct kvm *kvm);
+extern int kvm_vcpu_ioctl_interrupt(struct kvm_vcpu *vcpu,
+			     struct kvm_mips_interrupt *irq);
+
+static inline void kvm_arch_hardware_unsetup(void) {}
+static inline void kvm_arch_sync_events(struct kvm *kvm) {}
+static inline void kvm_arch_free_memslot(struct kvm *kvm,
+					 struct kvm_memory_slot *slot) {}
+static inline void kvm_arch_memslots_updated(struct kvm *kvm, u64 gen) {}
+static inline void kvm_arch_sched_in(struct kvm_vcpu *vcpu, int cpu) {}
+static inline void kvm_arch_vcpu_blocking(struct kvm_vcpu *vcpu) {}
+static inline void kvm_arch_vcpu_unblocking(struct kvm_vcpu *vcpu) {}
+
+#define __KVM_HAVE_ARCH_FLUSH_REMOTE_TLB
+int kvm_arch_flush_remote_tlb(struct kvm *kvm);
+
+#endif /* __MIPS_KVM_HOST_H__ */
diff --git a/arch/mips/include/asm/kvm_types.h b/arch/mips/include/asm/kvm_types.h
new file mode 100644
index 000000000..213754d9e
--- /dev/null
+++ b/arch/mips/include/asm/kvm_types.h
@@ -0,0 +1,7 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _ASM_MIPS_KVM_TYPES_H
+#define _ASM_MIPS_KVM_TYPES_H
+
+#define KVM_ARCH_NR_OBJS_PER_MEMORY_CACHE     4
+
+#endif /* _ASM_MIPS_KVM_TYPES_H */
diff --git a/arch/mips/include/asm/linkage.h b/arch/mips/include/asm/linkage.h
new file mode 100644
index 000000000..1829c2b6d
--- /dev/null
+++ b/arch/mips/include/asm/linkage.h
@@ -0,0 +1,13 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_LINKAGE_H
+#define __ASM_LINKAGE_H
+
+#ifdef __ASSEMBLY__
+#include <asm/asm.h>
+#endif
+
+#define cond_syscall(x) asm(".weak\t" #x "\n" #x "\t=\tsys_ni_syscall")
+#define SYSCALL_ALIAS(alias, name)					\
+	asm ( #alias " = " #name "\n\t.globl " #alias)
+
+#endif
diff --git a/arch/mips/include/asm/local.h b/arch/mips/include/asm/local.h
new file mode 100644
index 000000000..08366b1fd
--- /dev/null
+++ b/arch/mips/include/asm/local.h
@@ -0,0 +1,175 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _ARCH_MIPS_LOCAL_H
+#define _ARCH_MIPS_LOCAL_H
+
+#include <linux/percpu.h>
+#include <linux/bitops.h>
+#include <linux/atomic.h>
+#include <asm/asm.h>
+#include <asm/cmpxchg.h>
+#include <asm/compiler.h>
+
+typedef struct
+{
+	atomic_long_t a;
+} local_t;
+
+#define LOCAL_INIT(i)	{ ATOMIC_LONG_INIT(i) }
+
+#define local_read(l)	atomic_long_read(&(l)->a)
+#define local_set(l, i) atomic_long_set(&(l)->a, (i))
+
+#define local_add(i, l) atomic_long_add((i), (&(l)->a))
+#define local_sub(i, l) atomic_long_sub((i), (&(l)->a))
+#define local_inc(l)	atomic_long_inc(&(l)->a)
+#define local_dec(l)	atomic_long_dec(&(l)->a)
+
+/*
+ * Same as above, but return the result value
+ */
+static __inline__ long local_add_return(long i, local_t * l)
+{
+	unsigned long result;
+
+	if (kernel_uses_llsc) {
+		unsigned long temp;
+
+		__asm__ __volatile__(
+		"	.set	push					\n"
+		"	.set	"MIPS_ISA_ARCH_LEVEL"			\n"
+			__SYNC(full, loongson3_war) "                   \n"
+		"1:"	__stringify(LONG_LL)	"	%1, %2		\n"
+			__stringify(LONG_ADDU)	"	%0, %1, %3	\n"
+			__stringify(LONG_SC)	"	%0, %2		\n"
+			__stringify(SC_BEQZ)	"	%0, 1b		\n"
+			__stringify(LONG_ADDU)	"	%0, %1, %3	\n"
+		"	.set	pop					\n"
+		: "=&r" (result), "=&r" (temp), "=m" (l->a.counter)
+		: "Ir" (i), "m" (l->a.counter)
+		: "memory");
+	} else {
+		unsigned long flags;
+
+		local_irq_save(flags);
+		result = l->a.counter;
+		result += i;
+		l->a.counter = result;
+		local_irq_restore(flags);
+	}
+
+	return result;
+}
+
+static __inline__ long local_sub_return(long i, local_t * l)
+{
+	unsigned long result;
+
+	if (kernel_uses_llsc) {
+		unsigned long temp;
+
+		__asm__ __volatile__(
+		"	.set	push					\n"
+		"	.set	"MIPS_ISA_ARCH_LEVEL"			\n"
+			__SYNC(full, loongson3_war) "                   \n"
+		"1:"	__stringify(LONG_LL)	"	%1, %2		\n"
+			__stringify(LONG_SUBU)	"	%0, %1, %3	\n"
+			__stringify(LONG_SUBU)	"	%0, %1, %3	\n"
+			__stringify(LONG_SC)	"	%0, %2		\n"
+			__stringify(SC_BEQZ)	"	%0, 1b		\n"
+			__stringify(LONG_SUBU)	"	%0, %1, %3	\n"
+		"	.set	pop					\n"
+		: "=&r" (result), "=&r" (temp), "=m" (l->a.counter)
+		: "Ir" (i), "m" (l->a.counter)
+		: "memory");
+	} else {
+		unsigned long flags;
+
+		local_irq_save(flags);
+		result = l->a.counter;
+		result -= i;
+		l->a.counter = result;
+		local_irq_restore(flags);
+	}
+
+	return result;
+}
+
+#define local_cmpxchg(l, o, n) \
+	((long)cmpxchg_local(&((l)->a.counter), (o), (n)))
+#define local_xchg(l, n) (atomic_long_xchg((&(l)->a), (n)))
+
+/**
+ * local_add_unless - add unless the number is a given value
+ * @l: pointer of type local_t
+ * @a: the amount to add to l...
+ * @u: ...unless l is equal to u.
+ *
+ * Atomically adds @a to @l, so long as it was not @u.
+ * Returns non-zero if @l was not @u, and zero otherwise.
+ */
+#define local_add_unless(l, a, u)				\
+({								\
+	long c, old;						\
+	c = local_read(l);					\
+	while (c != (u) && (old = local_cmpxchg((l), c, c + (a))) != c) \
+		c = old;					\
+	c != (u);						\
+})
+#define local_inc_not_zero(l) local_add_unless((l), 1, 0)
+
+#define local_dec_return(l) local_sub_return(1, (l))
+#define local_inc_return(l) local_add_return(1, (l))
+
+/*
+ * local_sub_and_test - subtract value from variable and test result
+ * @i: integer value to subtract
+ * @l: pointer of type local_t
+ *
+ * Atomically subtracts @i from @l and returns
+ * true if the result is zero, or false for all
+ * other cases.
+ */
+#define local_sub_and_test(i, l) (local_sub_return((i), (l)) == 0)
+
+/*
+ * local_inc_and_test - increment and test
+ * @l: pointer of type local_t
+ *
+ * Atomically increments @l by 1
+ * and returns true if the result is zero, or false for all
+ * other cases.
+ */
+#define local_inc_and_test(l) (local_inc_return(l) == 0)
+
+/*
+ * local_dec_and_test - decrement by 1 and test
+ * @l: pointer of type local_t
+ *
+ * Atomically decrements @l by 1 and
+ * returns true if the result is 0, or false for all other
+ * cases.
+ */
+#define local_dec_and_test(l) (local_sub_return(1, (l)) == 0)
+
+/*
+ * local_add_negative - add and test if negative
+ * @l: pointer of type local_t
+ * @i: integer value to add
+ *
+ * Atomically adds @i to @l and returns true
+ * if the result is negative, or false when
+ * result is greater than or equal to zero.
+ */
+#define local_add_negative(i, l) (local_add_return(i, (l)) < 0)
+
+/* Use these for per-cpu local_t variables: on some archs they are
+ * much more efficient than these naive implementations.  Note they take
+ * a variable, not an address.
+ */
+
+#define __local_inc(l)		((l)->a.counter++)
+#define __local_dec(l)		((l)->a.counter++)
+#define __local_add(i, l)	((l)->a.counter+=(i))
+#define __local_sub(i, l)	((l)->a.counter-=(i))
+
+#endif /* _ARCH_MIPS_LOCAL_H */
diff --git a/arch/mips/include/asm/maar.h b/arch/mips/include/asm/maar.h
new file mode 100644
index 000000000..99f1c3e4b
--- /dev/null
+++ b/arch/mips/include/asm/maar.h
@@ -0,0 +1,127 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2014 Imagination Technologies
+ * Author: Paul Burton <paul.burton@mips.com>
+ */
+
+#ifndef __MIPS_ASM_MIPS_MAAR_H__
+#define __MIPS_ASM_MIPS_MAAR_H__
+
+#include <asm/hazards.h>
+#include <asm/mipsregs.h>
+
+/**
+ * platform_maar_init() - perform platform-level MAAR configuration
+ * @num_pairs:	The number of MAAR pairs present in the system.
+ *
+ * Platforms should implement this function such that it configures as many
+ * MAAR pairs as required, from 0 up to the maximum of num_pairs-1, and returns
+ * the number that were used. Any further MAARs will be configured to be
+ * invalid. The default implementation of this function will simply indicate
+ * that it has configured 0 MAAR pairs.
+ *
+ * Return:	The number of MAAR pairs configured.
+ */
+unsigned platform_maar_init(unsigned num_pairs);
+
+/**
+ * write_maar_pair() - write to a pair of MAARs
+ * @idx:	The index of the pair (ie. use MAARs idx*2 & (idx*2)+1).
+ * @lower:	The lowest address that the MAAR pair will affect. Must be
+ *		aligned to a 2^16 byte boundary.
+ * @upper:	The highest address that the MAAR pair will affect. Must be
+ *		aligned to one byte before a 2^16 byte boundary.
+ * @attrs:	The accessibility attributes to program, eg. MIPS_MAAR_S. The
+ *		MIPS_MAAR_VL/MIPS_MAAR_VH attributes will automatically be set.
+ *
+ * Program the pair of MAAR registers specified by idx to apply the attributes
+ * specified by attrs to the range of addresses from lower to higher.
+ */
+static inline void write_maar_pair(unsigned idx, phys_addr_t lower,
+				   phys_addr_t upper, unsigned attrs)
+{
+	/* Addresses begin at bit 16, but are shifted right 4 bits */
+	BUG_ON(lower & (0xffff | ~(MIPS_MAAR_ADDR << 4)));
+	BUG_ON(((upper & 0xffff) != 0xffff)
+		|| ((upper & ~0xffffull) & ~(MIPS_MAAR_ADDR << 4)));
+
+	/* Automatically set MIPS_MAAR_VL */
+	attrs |= MIPS_MAAR_VL;
+
+	/*
+	 * Write the upper address & attributes (both MIPS_MAAR_VL and
+	 * MIPS_MAAR_VH matter)
+	 */
+	write_c0_maari(idx << 1);
+	back_to_back_c0_hazard();
+	write_c0_maar(((upper >> 4) & MIPS_MAAR_ADDR) | attrs);
+	back_to_back_c0_hazard();
+#ifdef CONFIG_XPA
+	upper >>= MIPS_MAARX_ADDR_SHIFT;
+	writex_c0_maar(((upper >> 4) & MIPS_MAARX_ADDR) | MIPS_MAARX_VH);
+	back_to_back_c0_hazard();
+#endif
+
+	/* Write the lower address & attributes */
+	write_c0_maari((idx << 1) | 0x1);
+	back_to_back_c0_hazard();
+	write_c0_maar((lower >> 4) | attrs);
+	back_to_back_c0_hazard();
+#ifdef CONFIG_XPA
+	lower >>= MIPS_MAARX_ADDR_SHIFT;
+	writex_c0_maar(((lower >> 4) & MIPS_MAARX_ADDR) | MIPS_MAARX_VH);
+	back_to_back_c0_hazard();
+#endif
+}
+
+/**
+ * maar_init() - initialise MAARs
+ *
+ * Performs initialisation of MAARs for the current CPU, making use of the
+ * platforms implementation of platform_maar_init where necessary and
+ * duplicating the setup it provides on secondary CPUs.
+ */
+extern void maar_init(void);
+
+/**
+ * struct maar_config - MAAR configuration data
+ * @lower:	The lowest address that the MAAR pair will affect. Must be
+ *		aligned to a 2^16 byte boundary.
+ * @upper:	The highest address that the MAAR pair will affect. Must be
+ *		aligned to one byte before a 2^16 byte boundary.
+ * @attrs:	The accessibility attributes to program, eg. MIPS_MAAR_S. The
+ *		MIPS_MAAR_VL attribute will automatically be set.
+ *
+ * Describes the configuration of a pair of Memory Accessibility Attribute
+ * Registers - applying attributes from attrs to the range of physical
+ * addresses from lower to upper inclusive.
+ */
+struct maar_config {
+	phys_addr_t lower;
+	phys_addr_t upper;
+	unsigned attrs;
+};
+
+/**
+ * maar_config() - configure MAARs according to provided data
+ * @cfg:	Pointer to an array of struct maar_config.
+ * @num_cfg:	The number of structs in the cfg array.
+ * @num_pairs:	The number of MAAR pairs present in the system.
+ *
+ * Configures as many MAARs as are present and specified in the cfg
+ * array with the values taken from the cfg array.
+ *
+ * Return:	The number of MAAR pairs configured.
+ */
+static inline unsigned maar_config(const struct maar_config *cfg,
+				   unsigned num_cfg, unsigned num_pairs)
+{
+	unsigned i;
+
+	for (i = 0; i < min(num_cfg, num_pairs); i++)
+		write_maar_pair(i, cfg[i].lower, cfg[i].upper, cfg[i].attrs);
+
+	return i;
+}
+
+#endif /* __MIPS_ASM_MIPS_MAAR_H__ */
diff --git a/arch/mips/include/asm/mach-ar7/ar7.h b/arch/mips/include/asm/mach-ar7/ar7.h
new file mode 100644
index 000000000..1e8621a6a
--- /dev/null
+++ b/arch/mips/include/asm/mach-ar7/ar7.h
@@ -0,0 +1,191 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2006,2007 Felix Fietkau <nbd@openwrt.org>
+ * Copyright (C) 2006,2007 Eugene Konev <ejka@openwrt.org>
+ */
+
+#ifndef __AR7_H__
+#define __AR7_H__
+
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/errno.h>
+
+#include <asm/addrspace.h>
+
+#define AR7_SDRAM_BASE	0x14000000
+
+#define AR7_REGS_BASE	0x08610000
+
+#define AR7_REGS_MAC0	(AR7_REGS_BASE + 0x0000)
+#define AR7_REGS_GPIO	(AR7_REGS_BASE + 0x0900)
+/* 0x08610A00 - 0x08610BFF (512 bytes, 128 bytes / clock) */
+#define AR7_REGS_POWER	(AR7_REGS_BASE + 0x0a00)
+#define AR7_REGS_CLOCKS (AR7_REGS_POWER + 0x80)
+#define UR8_REGS_CLOCKS (AR7_REGS_POWER + 0x20)
+#define AR7_REGS_UART0	(AR7_REGS_BASE + 0x0e00)
+#define AR7_REGS_USB	(AR7_REGS_BASE + 0x1200)
+#define AR7_REGS_RESET	(AR7_REGS_BASE + 0x1600)
+#define AR7_REGS_PINSEL (AR7_REGS_BASE + 0x160C)
+#define AR7_REGS_VLYNQ0 (AR7_REGS_BASE + 0x1800)
+#define AR7_REGS_DCL	(AR7_REGS_BASE + 0x1a00)
+#define AR7_REGS_VLYNQ1 (AR7_REGS_BASE + 0x1c00)
+#define AR7_REGS_MDIO	(AR7_REGS_BASE + 0x1e00)
+#define AR7_REGS_IRQ	(AR7_REGS_BASE + 0x2400)
+#define AR7_REGS_MAC1	(AR7_REGS_BASE + 0x2800)
+
+#define AR7_REGS_WDT	(AR7_REGS_BASE + 0x1f00)
+#define UR8_REGS_WDT	(AR7_REGS_BASE + 0x0b00)
+#define UR8_REGS_UART1	(AR7_REGS_BASE + 0x0f00)
+
+/* Titan registers */
+#define TITAN_REGS_ESWITCH_BASE (0x08640000)
+#define TITAN_REGS_MAC0		(TITAN_REGS_ESWITCH_BASE)
+#define TITAN_REGS_MAC1		(TITAN_REGS_ESWITCH_BASE + 0x0800)
+#define TITAN_REGS_MDIO		(TITAN_REGS_ESWITCH_BASE + 0x02000)
+#define TITAN_REGS_VLYNQ0	(AR7_REGS_BASE + 0x1c00)
+#define TITAN_REGS_VLYNQ1	(AR7_REGS_BASE + 0x1300)
+
+#define AR7_RESET_PERIPHERAL	0x0
+#define AR7_RESET_SOFTWARE	0x4
+#define AR7_RESET_STATUS	0x8
+
+#define AR7_RESET_BIT_CPMAC_LO	17
+#define AR7_RESET_BIT_CPMAC_HI	21
+#define AR7_RESET_BIT_MDIO	22
+#define AR7_RESET_BIT_EPHY	26
+
+#define TITAN_RESET_BIT_EPHY1	28
+
+/* GPIO control registers */
+#define AR7_GPIO_INPUT	0x0
+#define AR7_GPIO_OUTPUT 0x4
+#define AR7_GPIO_DIR	0x8
+#define AR7_GPIO_ENABLE 0xc
+#define TITAN_GPIO_INPUT_0	0x0
+#define TITAN_GPIO_INPUT_1	0x4
+#define TITAN_GPIO_OUTPUT_0	0x8
+#define TITAN_GPIO_OUTPUT_1	0xc
+#define TITAN_GPIO_DIR_0	0x10
+#define TITAN_GPIO_DIR_1	0x14
+#define TITAN_GPIO_ENBL_0	0x18
+#define TITAN_GPIO_ENBL_1	0x1c
+
+#define AR7_CHIP_7100	0x18
+#define AR7_CHIP_7200	0x2b
+#define AR7_CHIP_7300	0x05
+#define AR7_CHIP_TITAN	0x07
+#define TITAN_CHIP_1050 0x0f
+#define TITAN_CHIP_1055 0x0e
+#define TITAN_CHIP_1056 0x0d
+#define TITAN_CHIP_1060 0x07
+
+/* Interrupts */
+#define AR7_IRQ_UART0	15
+#define AR7_IRQ_UART1	16
+
+/* Clocks */
+#define AR7_AFE_CLOCK	35328000
+#define AR7_REF_CLOCK	25000000
+#define AR7_XTAL_CLOCK	24000000
+
+/* DCL */
+#define AR7_WDT_HW_ENA	0x10
+
+struct plat_cpmac_data {
+	int reset_bit;
+	int power_bit;
+	u32 phy_mask;
+	char dev_addr[6];
+};
+
+struct plat_dsl_data {
+	int reset_bit_dsl;
+	int reset_bit_sar;
+};
+
+static inline int ar7_is_titan(void)
+{
+	return (readl((void *)KSEG1ADDR(AR7_REGS_GPIO + 0x24)) & 0xffff) ==
+		AR7_CHIP_TITAN;
+}
+
+static inline u16 ar7_chip_id(void)
+{
+	return ar7_is_titan() ? AR7_CHIP_TITAN : (readl((void *)
+		KSEG1ADDR(AR7_REGS_GPIO + 0x14)) & 0xffff);
+}
+
+static inline u16 titan_chip_id(void)
+{
+	unsigned int val = readl((void *)KSEG1ADDR(AR7_REGS_GPIO +
+						TITAN_GPIO_INPUT_1));
+	return ((val >> 12) & 0x0f);
+}
+
+static inline u8 ar7_chip_rev(void)
+{
+	return (readl((void *)KSEG1ADDR(AR7_REGS_GPIO + (ar7_is_titan() ? 0x24 :
+		0x14))) >> 16) & 0xff;
+}
+
+static inline int ar7_has_high_cpmac(void)
+{
+	u16 chip_id = ar7_chip_id();
+	switch (chip_id) {
+	case AR7_CHIP_7100:
+	case AR7_CHIP_7200:
+		return 0;
+	case AR7_CHIP_7300:
+		return 1;
+	default:
+		return -ENXIO;
+	}
+}
+#define ar7_has_high_vlynq ar7_has_high_cpmac
+#define ar7_has_second_uart ar7_has_high_cpmac
+
+static inline void ar7_device_enable(u32 bit)
+{
+	void *reset_reg =
+		(void *)KSEG1ADDR(AR7_REGS_RESET + AR7_RESET_PERIPHERAL);
+	writel(readl(reset_reg) | (1 << bit), reset_reg);
+	msleep(20);
+}
+
+static inline void ar7_device_disable(u32 bit)
+{
+	void *reset_reg =
+		(void *)KSEG1ADDR(AR7_REGS_RESET + AR7_RESET_PERIPHERAL);
+	writel(readl(reset_reg) & ~(1 << bit), reset_reg);
+	msleep(20);
+}
+
+static inline void ar7_device_reset(u32 bit)
+{
+	ar7_device_disable(bit);
+	ar7_device_enable(bit);
+}
+
+static inline void ar7_device_on(u32 bit)
+{
+	void *power_reg = (void *)KSEG1ADDR(AR7_REGS_POWER);
+	writel(readl(power_reg) | (1 << bit), power_reg);
+	msleep(20);
+}
+
+static inline void ar7_device_off(u32 bit)
+{
+	void *power_reg = (void *)KSEG1ADDR(AR7_REGS_POWER);
+	writel(readl(power_reg) & ~(1 << bit), power_reg);
+	msleep(20);
+}
+
+int __init ar7_gpio_init(void);
+void __init ar7_init_clocks(void);
+
+/* Board specific GPIO functions */
+int ar7_gpio_enable(unsigned gpio);
+int ar7_gpio_disable(unsigned gpio);
+
+#endif /* __AR7_H__ */
diff --git a/arch/mips/include/asm/mach-ar7/irq.h b/arch/mips/include/asm/mach-ar7/irq.h
new file mode 100644
index 000000000..46bb730ea
--- /dev/null
+++ b/arch/mips/include/asm/mach-ar7/irq.h
@@ -0,0 +1,16 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Shamelessly copied from asm-mips/mach-emma2rh/
+ * Copyright (C) 2003 by Ralf Baechle
+ */
+#ifndef __ASM_AR7_IRQ_H
+#define __ASM_AR7_IRQ_H
+
+#define NR_IRQS 256
+
+#include <asm/mach-generic/irq.h>
+
+#endif /* __ASM_AR7_IRQ_H */
diff --git a/arch/mips/include/asm/mach-ar7/prom.h b/arch/mips/include/asm/mach-ar7/prom.h
new file mode 100644
index 000000000..9e1d20b06
--- /dev/null
+++ b/arch/mips/include/asm/mach-ar7/prom.h
@@ -0,0 +1,12 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2006, 2007 Florian Fainelli <florian@openwrt.org>
+ */
+
+#ifndef __PROM_H__
+#define __PROM_H__
+
+extern char *prom_getenv(const char *name);
+extern void prom_meminit(void);
+
+#endif /* __PROM_H__ */
diff --git a/arch/mips/include/asm/mach-ar7/spaces.h b/arch/mips/include/asm/mach-ar7/spaces.h
new file mode 100644
index 000000000..a004d94df
--- /dev/null
+++ b/arch/mips/include/asm/mach-ar7/spaces.h
@@ -0,0 +1,22 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994 - 1999, 2000, 03, 04 Ralf Baechle
+ * Copyright (C) 2000, 2002  Maciej W. Rozycki
+ * Copyright (C) 1990, 1999, 2000 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_AR7_SPACES_H
+#define _ASM_AR7_SPACES_H
+
+/*
+ * This handles the memory map.
+ * We handle pages at KSEG0 for kernels with 32 bit address space.
+ */
+#define PAGE_OFFSET	_AC(0x94000000, UL)
+#define PHYS_OFFSET	_AC(0x14000000, UL)
+
+#include <asm/mach-generic/spaces.h>
+
+#endif /* __ASM_AR7_SPACES_H */
diff --git a/arch/mips/include/asm/mach-ath25/ath25_platform.h b/arch/mips/include/asm/mach-ath25/ath25_platform.h
new file mode 100644
index 000000000..0aacc55aa
--- /dev/null
+++ b/arch/mips/include/asm/mach-ath25/ath25_platform.h
@@ -0,0 +1,74 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_MACH_ATH25_PLATFORM_H
+#define __ASM_MACH_ATH25_PLATFORM_H
+
+#include <linux/etherdevice.h>
+
+/*
+ * This is board-specific data that is stored in a "fixed" location in flash.
+ * It is shared across operating systems, so it should not be changed lightly.
+ * The main reason we need it is in order to extract the ethernet MAC
+ * address(es).
+ */
+struct ath25_boarddata {
+	u32 magic;                   /* board data is valid */
+#define ATH25_BD_MAGIC 0x35333131    /* "5311", for all 531x/231x platforms */
+	u16 cksum;                   /* checksum (starting with BD_REV 2) */
+	u16 rev;                     /* revision of this struct */
+#define BD_REV 4
+	char board_name[64];         /* Name of board */
+	u16 major;                   /* Board major number */
+	u16 minor;                   /* Board minor number */
+	u32 flags;                   /* Board configuration */
+#define BD_ENET0        0x00000001   /* ENET0 is stuffed */
+#define BD_ENET1        0x00000002   /* ENET1 is stuffed */
+#define BD_UART1        0x00000004   /* UART1 is stuffed */
+#define BD_UART0        0x00000008   /* UART0 is stuffed (dma) */
+#define BD_RSTFACTORY   0x00000010   /* Reset factory defaults stuffed */
+#define BD_SYSLED       0x00000020   /* System LED stuffed */
+#define BD_EXTUARTCLK   0x00000040   /* External UART clock */
+#define BD_CPUFREQ      0x00000080   /* cpu freq is valid in nvram */
+#define BD_SYSFREQ      0x00000100   /* sys freq is set in nvram */
+#define BD_WLAN0        0x00000200   /* Enable WLAN0 */
+#define BD_MEMCAP       0x00000400   /* CAP SDRAM @ mem_cap for testing */
+#define BD_DISWATCHDOG  0x00000800   /* disable system watchdog */
+#define BD_WLAN1        0x00001000   /* Enable WLAN1 (ar5212) */
+#define BD_ISCASPER     0x00002000   /* FLAG for AR2312 */
+#define BD_WLAN0_2G_EN  0x00004000   /* FLAG for radio0_2G */
+#define BD_WLAN0_5G_EN  0x00008000   /* FLAG for radio0_2G */
+#define BD_WLAN1_2G_EN  0x00020000   /* FLAG for radio0_2G */
+#define BD_WLAN1_5G_EN  0x00040000   /* FLAG for radio0_2G */
+	u16 reset_config_gpio;       /* Reset factory GPIO pin */
+	u16 sys_led_gpio;            /* System LED GPIO pin */
+
+	u32 cpu_freq;                /* CPU core frequency in Hz */
+	u32 sys_freq;                /* System frequency in Hz */
+	u32 cnt_freq;                /* Calculated C0_COUNT frequency */
+
+	u8  wlan0_mac[ETH_ALEN];
+	u8  enet0_mac[ETH_ALEN];
+	u8  enet1_mac[ETH_ALEN];
+
+	u16 pci_id;                  /* Pseudo PCIID for common code */
+	u16 mem_cap;                 /* cap bank1 in MB */
+
+	/* version 3 */
+	u8  wlan1_mac[ETH_ALEN];     /* (ar5212) */
+};
+
+#define BOARD_CONFIG_BUFSZ		0x1000
+
+/*
+ * Platform device information for the Wireless MAC
+ */
+struct ar231x_board_config {
+	u16 devid;
+
+	/* board config data */
+	struct ath25_boarddata *config;
+
+	/* radio calibration data */
+	const char *radio;
+};
+
+#endif /* __ASM_MACH_ATH25_PLATFORM_H */
diff --git a/arch/mips/include/asm/mach-ath25/cpu-feature-overrides.h b/arch/mips/include/asm/mach-ath25/cpu-feature-overrides.h
new file mode 100644
index 000000000..ec3604c44
--- /dev/null
+++ b/arch/mips/include/asm/mach-ath25/cpu-feature-overrides.h
@@ -0,0 +1,59 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *  Atheros AR231x/AR531x SoC specific CPU feature overrides
+ *
+ *  Copyright (C) 2008 Gabor Juhos <juhosg@openwrt.org>
+ *
+ *  This file was derived from: include/asm-mips/cpu-features.h
+ *	Copyright (C) 2003, 2004 Ralf Baechle
+ *	Copyright (C) 2004 Maciej W. Rozycki
+ */
+#ifndef __ASM_MACH_ATH25_CPU_FEATURE_OVERRIDES_H
+#define __ASM_MACH_ATH25_CPU_FEATURE_OVERRIDES_H
+
+/*
+ * The Atheros AR531x/AR231x SoCs have MIPS 4Kc/4KEc core.
+ */
+#define cpu_has_tlb			1
+#define cpu_has_4kex			1
+#define cpu_has_3k_cache		0
+#define cpu_has_4k_cache		1
+#define cpu_has_sb1_cache		0
+#define cpu_has_fpu			0
+#define cpu_has_32fpr			0
+#define cpu_has_counter			1
+#define cpu_has_ejtag			1
+
+#if !defined(CONFIG_SOC_AR5312)
+#  define cpu_has_llsc			1
+#else
+/*
+ * The MIPS 4Kc V0.9 core in the AR5312/AR2312 have problems with the
+ * ll/sc instructions.
+ */
+#  define cpu_has_llsc			0
+#endif
+
+#define cpu_has_mips16			0
+#define cpu_has_mips16e2		0
+#define cpu_has_mdmx			0
+#define cpu_has_mips3d			0
+#define cpu_has_smartmips		0
+
+#define cpu_has_mips32r1		1
+
+#if !defined(CONFIG_SOC_AR5312)
+#  define cpu_has_mips32r2		1
+#endif
+
+#define cpu_has_mips64r1		0
+#define cpu_has_mips64r2		0
+
+#define cpu_has_dsp			0
+#define cpu_has_mipsmt			0
+
+#define cpu_has_64bits			0
+#define cpu_has_64bit_zero_reg		0
+#define cpu_has_64bit_gp_regs		0
+
+#endif /* __ASM_MACH_ATH25_CPU_FEATURE_OVERRIDES_H */
diff --git a/arch/mips/include/asm/mach-ath79/ar71xx_regs.h b/arch/mips/include/asm/mach-ath79/ar71xx_regs.h
new file mode 100644
index 000000000..5f8370607
--- /dev/null
+++ b/arch/mips/include/asm/mach-ath79/ar71xx_regs.h
@@ -0,0 +1,1322 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *  Atheros AR71XX/AR724X/AR913X SoC register definitions
+ *
+ *  Copyright (C) 2010-2011 Jaiganesh Narayanan <jnarayanan@atheros.com>
+ *  Copyright (C) 2008-2010 Gabor Juhos <juhosg@openwrt.org>
+ *  Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ *
+ *  Parts of this file are based on Atheros' 2.6.15/2.6.31 BSP
+ */
+
+#ifndef __ASM_MACH_AR71XX_REGS_H
+#define __ASM_MACH_AR71XX_REGS_H
+
+#include <linux/types.h>
+#include <linux/io.h>
+#include <linux/bitops.h>
+
+#define AR71XX_APB_BASE		0x18000000
+#define AR71XX_GE0_BASE		0x19000000
+#define AR71XX_GE0_SIZE		0x10000
+#define AR71XX_GE1_BASE		0x1a000000
+#define AR71XX_GE1_SIZE		0x10000
+#define AR71XX_EHCI_BASE	0x1b000000
+#define AR71XX_EHCI_SIZE	0x1000
+#define AR71XX_OHCI_BASE	0x1c000000
+#define AR71XX_OHCI_SIZE	0x1000
+#define AR71XX_SPI_BASE		0x1f000000
+#define AR71XX_SPI_SIZE		0x01000000
+
+#define AR71XX_DDR_CTRL_BASE	(AR71XX_APB_BASE + 0x00000000)
+#define AR71XX_DDR_CTRL_SIZE	0x100
+#define AR71XX_UART_BASE	(AR71XX_APB_BASE + 0x00020000)
+#define AR71XX_UART_SIZE	0x100
+#define AR71XX_USB_CTRL_BASE	(AR71XX_APB_BASE + 0x00030000)
+#define AR71XX_USB_CTRL_SIZE	0x100
+#define AR71XX_GPIO_BASE	(AR71XX_APB_BASE + 0x00040000)
+#define AR71XX_GPIO_SIZE	0x100
+#define AR71XX_PLL_BASE		(AR71XX_APB_BASE + 0x00050000)
+#define AR71XX_PLL_SIZE		0x100
+#define AR71XX_RESET_BASE	(AR71XX_APB_BASE + 0x00060000)
+#define AR71XX_RESET_SIZE	0x100
+#define AR71XX_MII_BASE		(AR71XX_APB_BASE + 0x00070000)
+#define AR71XX_MII_SIZE		0x100
+
+#define AR71XX_PCI_MEM_BASE	0x10000000
+#define AR71XX_PCI_MEM_SIZE	0x07000000
+
+#define AR71XX_PCI_WIN0_OFFS	0x10000000
+#define AR71XX_PCI_WIN1_OFFS	0x11000000
+#define AR71XX_PCI_WIN2_OFFS	0x12000000
+#define AR71XX_PCI_WIN3_OFFS	0x13000000
+#define AR71XX_PCI_WIN4_OFFS	0x14000000
+#define AR71XX_PCI_WIN5_OFFS	0x15000000
+#define AR71XX_PCI_WIN6_OFFS	0x16000000
+#define AR71XX_PCI_WIN7_OFFS	0x07000000
+
+#define AR71XX_PCI_CFG_BASE	\
+	(AR71XX_PCI_MEM_BASE + AR71XX_PCI_WIN7_OFFS + 0x10000)
+#define AR71XX_PCI_CFG_SIZE	0x100
+
+#define AR7240_USB_CTRL_BASE	(AR71XX_APB_BASE + 0x00030000)
+#define AR7240_USB_CTRL_SIZE	0x100
+#define AR7240_OHCI_BASE	0x1b000000
+#define AR7240_OHCI_SIZE	0x1000
+
+#define AR724X_PCI_MEM_BASE	0x10000000
+#define AR724X_PCI_MEM_SIZE	0x04000000
+
+#define AR724X_PCI_CFG_BASE	0x14000000
+#define AR724X_PCI_CFG_SIZE	0x1000
+#define AR724X_PCI_CRP_BASE	(AR71XX_APB_BASE + 0x000c0000)
+#define AR724X_PCI_CRP_SIZE	0x1000
+#define AR724X_PCI_CTRL_BASE	(AR71XX_APB_BASE + 0x000f0000)
+#define AR724X_PCI_CTRL_SIZE	0x100
+
+#define AR724X_EHCI_BASE	0x1b000000
+#define AR724X_EHCI_SIZE	0x1000
+
+#define AR913X_EHCI_BASE	0x1b000000
+#define AR913X_EHCI_SIZE	0x1000
+#define AR913X_WMAC_BASE	(AR71XX_APB_BASE + 0x000C0000)
+#define AR913X_WMAC_SIZE	0x30000
+
+#define AR933X_UART_BASE	(AR71XX_APB_BASE + 0x00020000)
+#define AR933X_UART_SIZE	0x14
+#define AR933X_GMAC_BASE	(AR71XX_APB_BASE + 0x00070000)
+#define AR933X_GMAC_SIZE	0x04
+#define AR933X_WMAC_BASE	(AR71XX_APB_BASE + 0x00100000)
+#define AR933X_WMAC_SIZE	0x20000
+#define AR933X_EHCI_BASE	0x1b000000
+#define AR933X_EHCI_SIZE	0x1000
+
+#define AR934X_GMAC_BASE	(AR71XX_APB_BASE + 0x00070000)
+#define AR934X_GMAC_SIZE	0x14
+#define AR934X_WMAC_BASE	(AR71XX_APB_BASE + 0x00100000)
+#define AR934X_WMAC_SIZE	0x20000
+#define AR934X_EHCI_BASE	0x1b000000
+#define AR934X_EHCI_SIZE	0x200
+#define AR934X_NFC_BASE		0x1b000200
+#define AR934X_NFC_SIZE		0xb8
+#define AR934X_SRIF_BASE	(AR71XX_APB_BASE + 0x00116000)
+#define AR934X_SRIF_SIZE	0x1000
+
+#define QCA953X_GMAC_BASE	(AR71XX_APB_BASE + 0x00070000)
+#define QCA953X_GMAC_SIZE	0x14
+#define QCA953X_WMAC_BASE	(AR71XX_APB_BASE + 0x00100000)
+#define QCA953X_WMAC_SIZE	0x20000
+#define QCA953X_EHCI_BASE	0x1b000000
+#define QCA953X_EHCI_SIZE	0x200
+#define QCA953X_SRIF_BASE	(AR71XX_APB_BASE + 0x00116000)
+#define QCA953X_SRIF_SIZE	0x1000
+
+#define QCA953X_PCI_CFG_BASE0	0x14000000
+#define QCA953X_PCI_CTRL_BASE0	(AR71XX_APB_BASE + 0x000f0000)
+#define QCA953X_PCI_CRP_BASE0	(AR71XX_APB_BASE + 0x000c0000)
+#define QCA953X_PCI_MEM_BASE0	0x10000000
+#define QCA953X_PCI_MEM_SIZE	0x02000000
+
+#define QCA955X_PCI_MEM_BASE0	0x10000000
+#define QCA955X_PCI_MEM_BASE1	0x12000000
+#define QCA955X_PCI_MEM_SIZE	0x02000000
+#define QCA955X_PCI_CFG_BASE0	0x14000000
+#define QCA955X_PCI_CFG_BASE1	0x16000000
+#define QCA955X_PCI_CFG_SIZE	0x1000
+#define QCA955X_PCI_CRP_BASE0	(AR71XX_APB_BASE + 0x000c0000)
+#define QCA955X_PCI_CRP_BASE1	(AR71XX_APB_BASE + 0x00250000)
+#define QCA955X_PCI_CRP_SIZE	0x1000
+#define QCA955X_PCI_CTRL_BASE0	(AR71XX_APB_BASE + 0x000f0000)
+#define QCA955X_PCI_CTRL_BASE1	(AR71XX_APB_BASE + 0x00280000)
+#define QCA955X_PCI_CTRL_SIZE	0x100
+
+#define QCA955X_GMAC_BASE	(AR71XX_APB_BASE + 0x00070000)
+#define QCA955X_GMAC_SIZE	0x40
+#define QCA955X_WMAC_BASE	(AR71XX_APB_BASE + 0x00100000)
+#define QCA955X_WMAC_SIZE	0x20000
+#define QCA955X_EHCI0_BASE	0x1b000000
+#define QCA955X_EHCI1_BASE	0x1b400000
+#define QCA955X_EHCI_SIZE	0x1000
+#define QCA955X_NFC_BASE	0x1b800200
+#define QCA955X_NFC_SIZE	0xb8
+
+#define QCA956X_PCI_MEM_BASE1	0x12000000
+#define QCA956X_PCI_MEM_SIZE	0x02000000
+#define QCA956X_PCI_CFG_BASE1	0x16000000
+#define QCA956X_PCI_CFG_SIZE	0x1000
+#define QCA956X_PCI_CRP_BASE1	(AR71XX_APB_BASE + 0x00250000)
+#define QCA956X_PCI_CRP_SIZE	0x1000
+#define QCA956X_PCI_CTRL_BASE1	(AR71XX_APB_BASE + 0x00280000)
+#define QCA956X_PCI_CTRL_SIZE	0x100
+
+#define QCA956X_WMAC_BASE	(AR71XX_APB_BASE + 0x00100000)
+#define QCA956X_WMAC_SIZE	0x20000
+#define QCA956X_EHCI0_BASE	0x1b000000
+#define QCA956X_EHCI1_BASE	0x1b400000
+#define QCA956X_EHCI_SIZE	0x200
+#define QCA956X_GMAC_SGMII_BASE	(AR71XX_APB_BASE + 0x00070000)
+#define QCA956X_GMAC_SGMII_SIZE	0x64
+#define QCA956X_PLL_BASE	(AR71XX_APB_BASE + 0x00050000)
+#define QCA956X_PLL_SIZE	0x50
+#define QCA956X_GMAC_BASE	(AR71XX_APB_BASE + 0x00070000)
+#define QCA956X_GMAC_SIZE	0x64
+
+/*
+ * Hidden Registers
+ */
+#define QCA956X_MAC_CFG_BASE		0xb9000000
+#define QCA956X_MAC_CFG_SIZE		0x64
+
+#define QCA956X_MAC_CFG1_REG		0x00
+#define QCA956X_MAC_CFG1_SOFT_RST	BIT(31)
+#define QCA956X_MAC_CFG1_RX_RST		BIT(19)
+#define QCA956X_MAC_CFG1_TX_RST		BIT(18)
+#define QCA956X_MAC_CFG1_LOOPBACK	BIT(8)
+#define QCA956X_MAC_CFG1_RX_EN		BIT(2)
+#define QCA956X_MAC_CFG1_TX_EN		BIT(0)
+
+#define QCA956X_MAC_CFG2_REG		0x04
+#define QCA956X_MAC_CFG2_IF_1000	BIT(9)
+#define QCA956X_MAC_CFG2_IF_10_100	BIT(8)
+#define QCA956X_MAC_CFG2_HUGE_FRAME_EN	BIT(5)
+#define QCA956X_MAC_CFG2_LEN_CHECK	BIT(4)
+#define QCA956X_MAC_CFG2_PAD_CRC_EN	BIT(2)
+#define QCA956X_MAC_CFG2_FDX		BIT(0)
+
+#define QCA956X_MAC_MII_MGMT_CFG_REG	0x20
+#define QCA956X_MGMT_CFG_CLK_DIV_20	0x07
+
+#define QCA956X_MAC_FIFO_CFG0_REG	0x48
+#define QCA956X_MAC_FIFO_CFG1_REG	0x4c
+#define QCA956X_MAC_FIFO_CFG2_REG	0x50
+#define QCA956X_MAC_FIFO_CFG3_REG	0x54
+#define QCA956X_MAC_FIFO_CFG4_REG	0x58
+#define QCA956X_MAC_FIFO_CFG5_REG	0x5c
+
+#define QCA956X_DAM_RESET_OFFSET	0xb90001bc
+#define QCA956X_DAM_RESET_SIZE		0x4
+#define QCA956X_INLINE_CHKSUM_ENG	BIT(27)
+
+/*
+ * DDR_CTRL block
+ */
+#define AR71XX_DDR_REG_PCI_WIN0		0x7c
+#define AR71XX_DDR_REG_PCI_WIN1		0x80
+#define AR71XX_DDR_REG_PCI_WIN2		0x84
+#define AR71XX_DDR_REG_PCI_WIN3		0x88
+#define AR71XX_DDR_REG_PCI_WIN4		0x8c
+#define AR71XX_DDR_REG_PCI_WIN5		0x90
+#define AR71XX_DDR_REG_PCI_WIN6		0x94
+#define AR71XX_DDR_REG_PCI_WIN7		0x98
+#define AR71XX_DDR_REG_FLUSH_GE0	0x9c
+#define AR71XX_DDR_REG_FLUSH_GE1	0xa0
+#define AR71XX_DDR_REG_FLUSH_USB	0xa4
+#define AR71XX_DDR_REG_FLUSH_PCI	0xa8
+
+#define AR724X_DDR_REG_FLUSH_GE0	0x7c
+#define AR724X_DDR_REG_FLUSH_GE1	0x80
+#define AR724X_DDR_REG_FLUSH_USB	0x84
+#define AR724X_DDR_REG_FLUSH_PCIE	0x88
+
+#define AR913X_DDR_REG_FLUSH_GE0	0x7c
+#define AR913X_DDR_REG_FLUSH_GE1	0x80
+#define AR913X_DDR_REG_FLUSH_USB	0x84
+#define AR913X_DDR_REG_FLUSH_WMAC	0x88
+
+#define AR933X_DDR_REG_FLUSH_GE0	0x7c
+#define AR933X_DDR_REG_FLUSH_GE1	0x80
+#define AR933X_DDR_REG_FLUSH_USB	0x84
+#define AR933X_DDR_REG_FLUSH_WMAC	0x88
+
+#define AR934X_DDR_REG_FLUSH_GE0	0x9c
+#define AR934X_DDR_REG_FLUSH_GE1	0xa0
+#define AR934X_DDR_REG_FLUSH_USB	0xa4
+#define AR934X_DDR_REG_FLUSH_PCIE	0xa8
+#define AR934X_DDR_REG_FLUSH_WMAC	0xac
+
+#define QCA953X_DDR_REG_FLUSH_GE0	0x9c
+#define QCA953X_DDR_REG_FLUSH_GE1	0xa0
+#define QCA953X_DDR_REG_FLUSH_USB	0xa4
+#define QCA953X_DDR_REG_FLUSH_PCIE	0xa8
+#define QCA953X_DDR_REG_FLUSH_WMAC	0xac
+
+/*
+ * PLL block
+ */
+#define AR71XX_PLL_REG_CPU_CONFIG	0x00
+#define AR71XX_PLL_REG_SEC_CONFIG	0x04
+#define AR71XX_PLL_REG_ETH0_INT_CLOCK	0x10
+#define AR71XX_PLL_REG_ETH1_INT_CLOCK	0x14
+
+#define AR71XX_PLL_FB_SHIFT		3
+#define AR71XX_PLL_FB_MASK		0x1f
+#define AR71XX_CPU_DIV_SHIFT		16
+#define AR71XX_CPU_DIV_MASK		0x3
+#define AR71XX_DDR_DIV_SHIFT		18
+#define AR71XX_DDR_DIV_MASK		0x3
+#define AR71XX_AHB_DIV_SHIFT		20
+#define AR71XX_AHB_DIV_MASK		0x7
+
+#define AR71XX_ETH0_PLL_SHIFT		17
+#define AR71XX_ETH1_PLL_SHIFT		19
+
+#define AR724X_PLL_REG_CPU_CONFIG	0x00
+#define AR724X_PLL_REG_PCIE_CONFIG	0x10
+
+#define AR724X_PLL_REG_PCIE_CONFIG_PPL_BYPASS	BIT(16)
+#define AR724X_PLL_REG_PCIE_CONFIG_PPL_RESET	BIT(25)
+
+#define AR724X_PLL_FB_SHIFT		0
+#define AR724X_PLL_FB_MASK		0x3ff
+#define AR724X_PLL_REF_DIV_SHIFT	10
+#define AR724X_PLL_REF_DIV_MASK		0xf
+#define AR724X_AHB_DIV_SHIFT		19
+#define AR724X_AHB_DIV_MASK		0x1
+#define AR724X_DDR_DIV_SHIFT		22
+#define AR724X_DDR_DIV_MASK		0x3
+
+#define AR7242_PLL_REG_ETH0_INT_CLOCK	0x2c
+
+#define AR913X_PLL_REG_CPU_CONFIG	0x00
+#define AR913X_PLL_REG_ETH_CONFIG	0x04
+#define AR913X_PLL_REG_ETH0_INT_CLOCK	0x14
+#define AR913X_PLL_REG_ETH1_INT_CLOCK	0x18
+
+#define AR913X_PLL_FB_SHIFT		0
+#define AR913X_PLL_FB_MASK		0x3ff
+#define AR913X_DDR_DIV_SHIFT		22
+#define AR913X_DDR_DIV_MASK		0x3
+#define AR913X_AHB_DIV_SHIFT		19
+#define AR913X_AHB_DIV_MASK		0x1
+
+#define AR913X_ETH0_PLL_SHIFT		20
+#define AR913X_ETH1_PLL_SHIFT		22
+
+#define AR933X_PLL_CPU_CONFIG_REG	0x00
+#define AR933X_PLL_CLOCK_CTRL_REG	0x08
+
+#define AR933X_PLL_CPU_CONFIG_NINT_SHIFT	10
+#define AR933X_PLL_CPU_CONFIG_NINT_MASK		0x3f
+#define AR933X_PLL_CPU_CONFIG_REFDIV_SHIFT	16
+#define AR933X_PLL_CPU_CONFIG_REFDIV_MASK	0x1f
+#define AR933X_PLL_CPU_CONFIG_OUTDIV_SHIFT	23
+#define AR933X_PLL_CPU_CONFIG_OUTDIV_MASK	0x7
+
+#define AR933X_PLL_CLOCK_CTRL_BYPASS		BIT(2)
+#define AR933X_PLL_CLOCK_CTRL_CPU_DIV_SHIFT	5
+#define AR933X_PLL_CLOCK_CTRL_CPU_DIV_MASK	0x3
+#define AR933X_PLL_CLOCK_CTRL_DDR_DIV_SHIFT	10
+#define AR933X_PLL_CLOCK_CTRL_DDR_DIV_MASK	0x3
+#define AR933X_PLL_CLOCK_CTRL_AHB_DIV_SHIFT	15
+#define AR933X_PLL_CLOCK_CTRL_AHB_DIV_MASK	0x7
+
+#define AR934X_PLL_CPU_CONFIG_REG		0x00
+#define AR934X_PLL_DDR_CONFIG_REG		0x04
+#define AR934X_PLL_CPU_DDR_CLK_CTRL_REG		0x08
+#define AR934X_PLL_SWITCH_CLOCK_CONTROL_REG	0x24
+#define AR934X_PLL_ETH_XMII_CONTROL_REG		0x2c
+
+#define AR934X_PLL_CPU_CONFIG_NFRAC_SHIFT	0
+#define AR934X_PLL_CPU_CONFIG_NFRAC_MASK	0x3f
+#define AR934X_PLL_CPU_CONFIG_NINT_SHIFT	6
+#define AR934X_PLL_CPU_CONFIG_NINT_MASK		0x3f
+#define AR934X_PLL_CPU_CONFIG_REFDIV_SHIFT	12
+#define AR934X_PLL_CPU_CONFIG_REFDIV_MASK	0x1f
+#define AR934X_PLL_CPU_CONFIG_OUTDIV_SHIFT	19
+#define AR934X_PLL_CPU_CONFIG_OUTDIV_MASK	0x3
+
+#define AR934X_PLL_DDR_CONFIG_NFRAC_SHIFT	0
+#define AR934X_PLL_DDR_CONFIG_NFRAC_MASK	0x3ff
+#define AR934X_PLL_DDR_CONFIG_NINT_SHIFT	10
+#define AR934X_PLL_DDR_CONFIG_NINT_MASK		0x3f
+#define AR934X_PLL_DDR_CONFIG_REFDIV_SHIFT	16
+#define AR934X_PLL_DDR_CONFIG_REFDIV_MASK	0x1f
+#define AR934X_PLL_DDR_CONFIG_OUTDIV_SHIFT	23
+#define AR934X_PLL_DDR_CONFIG_OUTDIV_MASK	0x7
+
+#define AR934X_PLL_CPU_DDR_CLK_CTRL_CPU_PLL_BYPASS	BIT(2)
+#define AR934X_PLL_CPU_DDR_CLK_CTRL_DDR_PLL_BYPASS	BIT(3)
+#define AR934X_PLL_CPU_DDR_CLK_CTRL_AHB_PLL_BYPASS	BIT(4)
+#define AR934X_PLL_CPU_DDR_CLK_CTRL_CPU_POST_DIV_SHIFT	5
+#define AR934X_PLL_CPU_DDR_CLK_CTRL_CPU_POST_DIV_MASK	0x1f
+#define AR934X_PLL_CPU_DDR_CLK_CTRL_DDR_POST_DIV_SHIFT	10
+#define AR934X_PLL_CPU_DDR_CLK_CTRL_DDR_POST_DIV_MASK	0x1f
+#define AR934X_PLL_CPU_DDR_CLK_CTRL_AHB_POST_DIV_SHIFT	15
+#define AR934X_PLL_CPU_DDR_CLK_CTRL_AHB_POST_DIV_MASK	0x1f
+#define AR934X_PLL_CPU_DDR_CLK_CTRL_CPUCLK_FROM_CPUPLL	BIT(20)
+#define AR934X_PLL_CPU_DDR_CLK_CTRL_DDRCLK_FROM_DDRPLL	BIT(21)
+#define AR934X_PLL_CPU_DDR_CLK_CTRL_AHBCLK_FROM_DDRPLL	BIT(24)
+
+#define AR934X_PLL_SWITCH_CLOCK_CONTROL_MDIO_CLK_SEL	BIT(6)
+
+#define QCA953X_PLL_CPU_CONFIG_REG		0x00
+#define QCA953X_PLL_DDR_CONFIG_REG		0x04
+#define QCA953X_PLL_CLK_CTRL_REG		0x08
+#define QCA953X_PLL_SWITCH_CLOCK_CONTROL_REG	0x24
+#define QCA953X_PLL_ETH_XMII_CONTROL_REG	0x2c
+#define QCA953X_PLL_ETH_SGMII_CONTROL_REG	0x48
+
+#define QCA953X_PLL_CPU_CONFIG_NFRAC_SHIFT	0
+#define QCA953X_PLL_CPU_CONFIG_NFRAC_MASK	0x3f
+#define QCA953X_PLL_CPU_CONFIG_NINT_SHIFT	6
+#define QCA953X_PLL_CPU_CONFIG_NINT_MASK	0x3f
+#define QCA953X_PLL_CPU_CONFIG_REFDIV_SHIFT	12
+#define QCA953X_PLL_CPU_CONFIG_REFDIV_MASK	0x1f
+#define QCA953X_PLL_CPU_CONFIG_OUTDIV_SHIFT	19
+#define QCA953X_PLL_CPU_CONFIG_OUTDIV_MASK	0x7
+
+#define QCA953X_PLL_DDR_CONFIG_NFRAC_SHIFT	0
+#define QCA953X_PLL_DDR_CONFIG_NFRAC_MASK	0x3ff
+#define QCA953X_PLL_DDR_CONFIG_NINT_SHIFT	10
+#define QCA953X_PLL_DDR_CONFIG_NINT_MASK	0x3f
+#define QCA953X_PLL_DDR_CONFIG_REFDIV_SHIFT	16
+#define QCA953X_PLL_DDR_CONFIG_REFDIV_MASK	0x1f
+#define QCA953X_PLL_DDR_CONFIG_OUTDIV_SHIFT	23
+#define QCA953X_PLL_DDR_CONFIG_OUTDIV_MASK	0x7
+
+#define QCA953X_PLL_CLK_CTRL_CPU_PLL_BYPASS		BIT(2)
+#define QCA953X_PLL_CLK_CTRL_DDR_PLL_BYPASS		BIT(3)
+#define QCA953X_PLL_CLK_CTRL_AHB_PLL_BYPASS		BIT(4)
+#define QCA953X_PLL_CLK_CTRL_CPU_POST_DIV_SHIFT		5
+#define QCA953X_PLL_CLK_CTRL_CPU_POST_DIV_MASK		0x1f
+#define QCA953X_PLL_CLK_CTRL_DDR_POST_DIV_SHIFT		10
+#define QCA953X_PLL_CLK_CTRL_DDR_POST_DIV_MASK		0x1f
+#define QCA953X_PLL_CLK_CTRL_AHB_POST_DIV_SHIFT		15
+#define QCA953X_PLL_CLK_CTRL_AHB_POST_DIV_MASK		0x1f
+#define QCA953X_PLL_CLK_CTRL_CPUCLK_FROM_CPUPLL		BIT(20)
+#define QCA953X_PLL_CLK_CTRL_DDRCLK_FROM_DDRPLL		BIT(21)
+#define QCA953X_PLL_CLK_CTRL_AHBCLK_FROM_DDRPLL		BIT(24)
+
+#define QCA955X_PLL_CPU_CONFIG_REG		0x00
+#define QCA955X_PLL_DDR_CONFIG_REG		0x04
+#define QCA955X_PLL_CLK_CTRL_REG		0x08
+#define QCA955X_PLL_ETH_XMII_CONTROL_REG	0x28
+#define QCA955X_PLL_ETH_SGMII_CONTROL_REG	0x48
+#define QCA955X_PLL_ETH_SGMII_SERDES_REG	0x4c
+
+#define QCA955X_PLL_CPU_CONFIG_NFRAC_SHIFT	0
+#define QCA955X_PLL_CPU_CONFIG_NFRAC_MASK	0x3f
+#define QCA955X_PLL_CPU_CONFIG_NINT_SHIFT	6
+#define QCA955X_PLL_CPU_CONFIG_NINT_MASK	0x3f
+#define QCA955X_PLL_CPU_CONFIG_REFDIV_SHIFT	12
+#define QCA955X_PLL_CPU_CONFIG_REFDIV_MASK	0x1f
+#define QCA955X_PLL_CPU_CONFIG_OUTDIV_SHIFT	19
+#define QCA955X_PLL_CPU_CONFIG_OUTDIV_MASK	0x3
+
+#define QCA955X_PLL_DDR_CONFIG_NFRAC_SHIFT	0
+#define QCA955X_PLL_DDR_CONFIG_NFRAC_MASK	0x3ff
+#define QCA955X_PLL_DDR_CONFIG_NINT_SHIFT	10
+#define QCA955X_PLL_DDR_CONFIG_NINT_MASK	0x3f
+#define QCA955X_PLL_DDR_CONFIG_REFDIV_SHIFT	16
+#define QCA955X_PLL_DDR_CONFIG_REFDIV_MASK	0x1f
+#define QCA955X_PLL_DDR_CONFIG_OUTDIV_SHIFT	23
+#define QCA955X_PLL_DDR_CONFIG_OUTDIV_MASK	0x7
+
+#define QCA955X_PLL_CLK_CTRL_CPU_PLL_BYPASS		BIT(2)
+#define QCA955X_PLL_CLK_CTRL_DDR_PLL_BYPASS		BIT(3)
+#define QCA955X_PLL_CLK_CTRL_AHB_PLL_BYPASS		BIT(4)
+#define QCA955X_PLL_CLK_CTRL_CPU_POST_DIV_SHIFT		5
+#define QCA955X_PLL_CLK_CTRL_CPU_POST_DIV_MASK		0x1f
+#define QCA955X_PLL_CLK_CTRL_DDR_POST_DIV_SHIFT		10
+#define QCA955X_PLL_CLK_CTRL_DDR_POST_DIV_MASK		0x1f
+#define QCA955X_PLL_CLK_CTRL_AHB_POST_DIV_SHIFT		15
+#define QCA955X_PLL_CLK_CTRL_AHB_POST_DIV_MASK		0x1f
+#define QCA955X_PLL_CLK_CTRL_CPUCLK_FROM_CPUPLL		BIT(20)
+#define QCA955X_PLL_CLK_CTRL_DDRCLK_FROM_DDRPLL		BIT(21)
+#define QCA955X_PLL_CLK_CTRL_AHBCLK_FROM_DDRPLL		BIT(24)
+
+#define QCA955X_PLL_ETH_SGMII_SERDES_LOCK_DETECT	BIT(2)
+#define QCA955X_PLL_ETH_SGMII_SERDES_PLL_REFCLK		BIT(1)
+#define QCA955X_PLL_ETH_SGMII_SERDES_EN_PLL		BIT(0)
+
+#define QCA956X_PLL_CPU_CONFIG_REG			0x00
+#define QCA956X_PLL_CPU_CONFIG1_REG			0x04
+#define QCA956X_PLL_DDR_CONFIG_REG			0x08
+#define QCA956X_PLL_DDR_CONFIG1_REG			0x0c
+#define QCA956X_PLL_CLK_CTRL_REG			0x10
+#define QCA956X_PLL_SWITCH_CLOCK_CONTROL_REG		0x28
+#define QCA956X_PLL_ETH_XMII_CONTROL_REG		0x30
+#define QCA956X_PLL_ETH_SGMII_SERDES_REG		0x4c
+
+#define QCA956X_PLL_CPU_CONFIG_REFDIV_SHIFT		12
+#define QCA956X_PLL_CPU_CONFIG_REFDIV_MASK		0x1f
+#define QCA956X_PLL_CPU_CONFIG_OUTDIV_SHIFT		19
+#define QCA956X_PLL_CPU_CONFIG_OUTDIV_MASK		0x7
+
+#define QCA956X_PLL_CPU_CONFIG1_NFRAC_L_SHIFT		0
+#define QCA956X_PLL_CPU_CONFIG1_NFRAC_L_MASK		0x1f
+#define QCA956X_PLL_CPU_CONFIG1_NFRAC_H_SHIFT		5
+#define QCA956X_PLL_CPU_CONFIG1_NFRAC_H_MASK		0x1fff
+#define QCA956X_PLL_CPU_CONFIG1_NINT_SHIFT		18
+#define QCA956X_PLL_CPU_CONFIG1_NINT_MASK		0x1ff
+
+#define QCA956X_PLL_DDR_CONFIG_REFDIV_SHIFT		16
+#define QCA956X_PLL_DDR_CONFIG_REFDIV_MASK		0x1f
+#define QCA956X_PLL_DDR_CONFIG_OUTDIV_SHIFT		23
+#define QCA956X_PLL_DDR_CONFIG_OUTDIV_MASK		0x7
+
+#define QCA956X_PLL_DDR_CONFIG1_NFRAC_L_SHIFT		0
+#define QCA956X_PLL_DDR_CONFIG1_NFRAC_L_MASK		0x1f
+#define QCA956X_PLL_DDR_CONFIG1_NFRAC_H_SHIFT		5
+#define QCA956X_PLL_DDR_CONFIG1_NFRAC_H_MASK		0x1fff
+#define QCA956X_PLL_DDR_CONFIG1_NINT_SHIFT		18
+#define QCA956X_PLL_DDR_CONFIG1_NINT_MASK		0x1ff
+
+#define QCA956X_PLL_CLK_CTRL_CPU_PLL_BYPASS		BIT(2)
+#define QCA956X_PLL_CLK_CTRL_DDR_PLL_BYPASS		BIT(3)
+#define QCA956X_PLL_CLK_CTRL_AHB_PLL_BYPASS		BIT(4)
+#define QCA956X_PLL_CLK_CTRL_CPU_POST_DIV_SHIFT		5
+#define QCA956X_PLL_CLK_CTRL_CPU_POST_DIV_MASK		0x1f
+#define QCA956X_PLL_CLK_CTRL_DDR_POST_DIV_SHIFT		10
+#define QCA956X_PLL_CLK_CTRL_DDR_POST_DIV_MASK		0x1f
+#define QCA956X_PLL_CLK_CTRL_AHB_POST_DIV_SHIFT		15
+#define QCA956X_PLL_CLK_CTRL_AHB_POST_DIV_MASK		0x1f
+#define QCA956X_PLL_CLK_CTRL_CPU_DDRCLK_FROM_DDRPLL	BIT(20)
+#define QCA956X_PLL_CLK_CTRL_CPU_DDRCLK_FROM_CPUPLL	BIT(21)
+#define QCA956X_PLL_CLK_CTRL_AHBCLK_FROM_DDRPLL		BIT(24)
+
+#define QCA956X_PLL_SWITCH_CLOCK_SPARE_I2C_CLK_SELB		BIT(5)
+#define QCA956X_PLL_SWITCH_CLOCK_SPARE_MDIO_CLK_SEL0_1		BIT(6)
+#define QCA956X_PLL_SWITCH_CLOCK_SPARE_UART1_CLK_SEL		BIT(7)
+#define QCA956X_PLL_SWITCH_CLOCK_SPARE_USB_REFCLK_FREQ_SEL_SHIFT 8
+#define QCA956X_PLL_SWITCH_CLOCK_SPARE_USB_REFCLK_FREQ_SEL_MASK	 0xf
+#define QCA956X_PLL_SWITCH_CLOCK_SPARE_EN_PLL_TOP		BIT(12)
+#define QCA956X_PLL_SWITCH_CLOCK_SPARE_MDIO_CLK_SEL0_2		BIT(13)
+#define QCA956X_PLL_SWITCH_CLOCK_SPARE_MDIO_CLK_SEL1_1		BIT(14)
+#define QCA956X_PLL_SWITCH_CLOCK_SPARE_MDIO_CLK_SEL1_2		BIT(15)
+#define QCA956X_PLL_SWITCH_CLOCK_SPARE_SWITCH_FUNC_TST_MODE	BIT(16)
+#define QCA956X_PLL_SWITCH_CLOCK_SPARE_EEE_ENABLE		BIT(17)
+#define QCA956X_PLL_SWITCH_CLOCK_SPARE_OEN_CLK125M_PLL		BIT(18)
+#define QCA956X_PLL_SWITCH_CLOCK_SPARE_SWITCHCLK_SEL		BIT(19)
+
+#define QCA956X_PLL_ETH_XMII_TX_INVERT			BIT(1)
+#define QCA956X_PLL_ETH_XMII_GIGE			BIT(25)
+#define QCA956X_PLL_ETH_XMII_RX_DELAY_SHIFT		28
+#define QCA956X_PLL_ETH_XMII_RX_DELAY_MASK		0x3
+#define QCA956X_PLL_ETH_XMII_TX_DELAY_SHIFT		26
+#define QCA956X_PLL_ETH_XMII_TX_DELAY_MASK		3
+
+#define QCA956X_PLL_ETH_SGMII_SERDES_LOCK_DETECT		BIT(2)
+#define QCA956X_PLL_ETH_SGMII_SERDES_PLL_REFCLK			BIT(1)
+#define QCA956X_PLL_ETH_SGMII_SERDES_EN_PLL			BIT(0)
+
+/*
+ * USB_CONFIG block
+ */
+#define AR71XX_USB_CTRL_REG_FLADJ	0x00
+#define AR71XX_USB_CTRL_REG_CONFIG	0x04
+
+/*
+ * RESET block
+ */
+#define AR71XX_RESET_REG_TIMER			0x00
+#define AR71XX_RESET_REG_TIMER_RELOAD		0x04
+#define AR71XX_RESET_REG_WDOG_CTRL		0x08
+#define AR71XX_RESET_REG_WDOG			0x0c
+#define AR71XX_RESET_REG_MISC_INT_STATUS	0x10
+#define AR71XX_RESET_REG_MISC_INT_ENABLE	0x14
+#define AR71XX_RESET_REG_PCI_INT_STATUS		0x18
+#define AR71XX_RESET_REG_PCI_INT_ENABLE		0x1c
+#define AR71XX_RESET_REG_GLOBAL_INT_STATUS	0x20
+#define AR71XX_RESET_REG_RESET_MODULE		0x24
+#define AR71XX_RESET_REG_PERFC_CTRL		0x2c
+#define AR71XX_RESET_REG_PERFC0			0x30
+#define AR71XX_RESET_REG_PERFC1			0x34
+#define AR71XX_RESET_REG_REV_ID			0x90
+
+#define AR913X_RESET_REG_GLOBAL_INT_STATUS	0x18
+#define AR913X_RESET_REG_RESET_MODULE		0x1c
+#define AR913X_RESET_REG_PERF_CTRL		0x20
+#define AR913X_RESET_REG_PERFC0			0x24
+#define AR913X_RESET_REG_PERFC1			0x28
+
+#define AR724X_RESET_REG_RESET_MODULE		0x1c
+
+#define AR933X_RESET_REG_RESET_MODULE		0x1c
+#define AR933X_RESET_REG_BOOTSTRAP		0xac
+
+#define AR934X_RESET_REG_RESET_MODULE		0x1c
+#define AR934X_RESET_REG_BOOTSTRAP		0xb0
+#define AR934X_RESET_REG_PCIE_WMAC_INT_STATUS	0xac
+
+#define QCA953X_RESET_REG_RESET_MODULE		0x1c
+#define QCA953X_RESET_REG_BOOTSTRAP		0xb0
+#define QCA953X_RESET_REG_PCIE_WMAC_INT_STATUS	0xac
+
+#define QCA955X_RESET_REG_RESET_MODULE		0x1c
+#define QCA955X_RESET_REG_BOOTSTRAP		0xb0
+#define QCA955X_RESET_REG_EXT_INT_STATUS	0xac
+
+#define QCA956X_RESET_REG_RESET_MODULE		0x1c
+#define QCA956X_RESET_REG_BOOTSTRAP		0xb0
+#define QCA956X_RESET_REG_EXT_INT_STATUS	0xac
+
+#define MISC_INT_MIPS_SI_TIMERINT_MASK	BIT(28)
+#define MISC_INT_ETHSW			BIT(12)
+#define MISC_INT_TIMER4			BIT(10)
+#define MISC_INT_TIMER3			BIT(9)
+#define MISC_INT_TIMER2			BIT(8)
+#define MISC_INT_DMA			BIT(7)
+#define MISC_INT_OHCI			BIT(6)
+#define MISC_INT_PERFC			BIT(5)
+#define MISC_INT_WDOG			BIT(4)
+#define MISC_INT_UART			BIT(3)
+#define MISC_INT_GPIO			BIT(2)
+#define MISC_INT_ERROR			BIT(1)
+#define MISC_INT_TIMER			BIT(0)
+
+#define AR71XX_RESET_EXTERNAL		BIT(28)
+#define AR71XX_RESET_FULL_CHIP		BIT(24)
+#define AR71XX_RESET_CPU_NMI		BIT(21)
+#define AR71XX_RESET_CPU_COLD		BIT(20)
+#define AR71XX_RESET_DMA		BIT(19)
+#define AR71XX_RESET_SLIC		BIT(18)
+#define AR71XX_RESET_STEREO		BIT(17)
+#define AR71XX_RESET_DDR		BIT(16)
+#define AR71XX_RESET_GE1_MAC		BIT(13)
+#define AR71XX_RESET_GE1_PHY		BIT(12)
+#define AR71XX_RESET_USBSUS_OVERRIDE	BIT(10)
+#define AR71XX_RESET_GE0_MAC		BIT(9)
+#define AR71XX_RESET_GE0_PHY		BIT(8)
+#define AR71XX_RESET_USB_OHCI_DLL	BIT(6)
+#define AR71XX_RESET_USB_HOST		BIT(5)
+#define AR71XX_RESET_USB_PHY		BIT(4)
+#define AR71XX_RESET_PCI_BUS		BIT(1)
+#define AR71XX_RESET_PCI_CORE		BIT(0)
+
+#define AR7240_RESET_USB_HOST		BIT(5)
+#define AR7240_RESET_OHCI_DLL		BIT(3)
+
+#define AR724X_RESET_GE1_MDIO		BIT(23)
+#define AR724X_RESET_GE0_MDIO		BIT(22)
+#define AR724X_RESET_PCIE_PHY_SERIAL	BIT(10)
+#define AR724X_RESET_PCIE_PHY		BIT(7)
+#define AR724X_RESET_PCIE		BIT(6)
+#define AR724X_RESET_USB_HOST		BIT(5)
+#define AR724X_RESET_USB_PHY		BIT(4)
+#define AR724X_RESET_USBSUS_OVERRIDE	BIT(3)
+
+#define AR913X_RESET_AMBA2WMAC		BIT(22)
+#define AR913X_RESET_USBSUS_OVERRIDE	BIT(10)
+#define AR913X_RESET_USB_HOST		BIT(5)
+#define AR913X_RESET_USB_PHY		BIT(4)
+
+#define AR933X_RESET_GE1_MDIO		BIT(23)
+#define AR933X_RESET_GE0_MDIO		BIT(22)
+#define AR933X_RESET_GE1_MAC		BIT(13)
+#define AR933X_RESET_WMAC		BIT(11)
+#define AR933X_RESET_GE0_MAC		BIT(9)
+#define AR933X_RESET_USB_HOST		BIT(5)
+#define AR933X_RESET_USB_PHY		BIT(4)
+#define AR933X_RESET_USBSUS_OVERRIDE	BIT(3)
+
+#define AR934X_RESET_HOST		BIT(31)
+#define AR934X_RESET_SLIC		BIT(30)
+#define AR934X_RESET_HDMA		BIT(29)
+#define AR934X_RESET_EXTERNAL		BIT(28)
+#define AR934X_RESET_RTC		BIT(27)
+#define AR934X_RESET_PCIE_EP_INT	BIT(26)
+#define AR934X_RESET_CHKSUM_ACC		BIT(25)
+#define AR934X_RESET_FULL_CHIP		BIT(24)
+#define AR934X_RESET_GE1_MDIO		BIT(23)
+#define AR934X_RESET_GE0_MDIO		BIT(22)
+#define AR934X_RESET_CPU_NMI		BIT(21)
+#define AR934X_RESET_CPU_COLD		BIT(20)
+#define AR934X_RESET_HOST_RESET_INT	BIT(19)
+#define AR934X_RESET_PCIE_EP		BIT(18)
+#define AR934X_RESET_UART1		BIT(17)
+#define AR934X_RESET_DDR		BIT(16)
+#define AR934X_RESET_USB_PHY_PLL_PWD_EXT BIT(15)
+#define AR934X_RESET_NANDF		BIT(14)
+#define AR934X_RESET_GE1_MAC		BIT(13)
+#define AR934X_RESET_ETH_SWITCH_ANALOG	BIT(12)
+#define AR934X_RESET_USB_PHY_ANALOG	BIT(11)
+#define AR934X_RESET_HOST_DMA_INT	BIT(10)
+#define AR934X_RESET_GE0_MAC		BIT(9)
+#define AR934X_RESET_ETH_SWITCH		BIT(8)
+#define AR934X_RESET_PCIE_PHY		BIT(7)
+#define AR934X_RESET_PCIE		BIT(6)
+#define AR934X_RESET_USB_HOST		BIT(5)
+#define AR934X_RESET_USB_PHY		BIT(4)
+#define AR934X_RESET_USBSUS_OVERRIDE	BIT(3)
+#define AR934X_RESET_LUT		BIT(2)
+#define AR934X_RESET_MBOX		BIT(1)
+#define AR934X_RESET_I2S		BIT(0)
+
+#define QCA953X_RESET_USB_EXT_PWR	BIT(29)
+#define QCA953X_RESET_EXTERNAL		BIT(28)
+#define QCA953X_RESET_RTC		BIT(27)
+#define QCA953X_RESET_FULL_CHIP		BIT(24)
+#define QCA953X_RESET_GE1_MDIO		BIT(23)
+#define QCA953X_RESET_GE0_MDIO		BIT(22)
+#define QCA953X_RESET_CPU_NMI		BIT(21)
+#define QCA953X_RESET_CPU_COLD		BIT(20)
+#define QCA953X_RESET_DDR		BIT(16)
+#define QCA953X_RESET_USB_PHY_PLL_PWD_EXT BIT(15)
+#define QCA953X_RESET_GE1_MAC		BIT(13)
+#define QCA953X_RESET_ETH_SWITCH_ANALOG	BIT(12)
+#define QCA953X_RESET_USB_PHY_ANALOG	BIT(11)
+#define QCA953X_RESET_GE0_MAC		BIT(9)
+#define QCA953X_RESET_ETH_SWITCH	BIT(8)
+#define QCA953X_RESET_PCIE_PHY		BIT(7)
+#define QCA953X_RESET_PCIE		BIT(6)
+#define QCA953X_RESET_USB_HOST		BIT(5)
+#define QCA953X_RESET_USB_PHY		BIT(4)
+#define QCA953X_RESET_USBSUS_OVERRIDE	BIT(3)
+
+#define QCA955X_RESET_HOST		BIT(31)
+#define QCA955X_RESET_SLIC		BIT(30)
+#define QCA955X_RESET_HDMA		BIT(29)
+#define QCA955X_RESET_EXTERNAL		BIT(28)
+#define QCA955X_RESET_RTC		BIT(27)
+#define QCA955X_RESET_PCIE_EP_INT	BIT(26)
+#define QCA955X_RESET_CHKSUM_ACC	BIT(25)
+#define QCA955X_RESET_FULL_CHIP		BIT(24)
+#define QCA955X_RESET_GE1_MDIO		BIT(23)
+#define QCA955X_RESET_GE0_MDIO		BIT(22)
+#define QCA955X_RESET_CPU_NMI		BIT(21)
+#define QCA955X_RESET_CPU_COLD		BIT(20)
+#define QCA955X_RESET_HOST_RESET_INT	BIT(19)
+#define QCA955X_RESET_PCIE_EP		BIT(18)
+#define QCA955X_RESET_UART1		BIT(17)
+#define QCA955X_RESET_DDR		BIT(16)
+#define QCA955X_RESET_USB_PHY_PLL_PWD_EXT BIT(15)
+#define QCA955X_RESET_NANDF		BIT(14)
+#define QCA955X_RESET_GE1_MAC		BIT(13)
+#define QCA955X_RESET_SGMII_ANALOG	BIT(12)
+#define QCA955X_RESET_USB_PHY_ANALOG	BIT(11)
+#define QCA955X_RESET_HOST_DMA_INT	BIT(10)
+#define QCA955X_RESET_GE0_MAC		BIT(9)
+#define QCA955X_RESET_SGMII		BIT(8)
+#define QCA955X_RESET_PCIE_PHY		BIT(7)
+#define QCA955X_RESET_PCIE		BIT(6)
+#define QCA955X_RESET_USB_HOST		BIT(5)
+#define QCA955X_RESET_USB_PHY		BIT(4)
+#define QCA955X_RESET_USBSUS_OVERRIDE	BIT(3)
+#define QCA955X_RESET_LUT		BIT(2)
+#define QCA955X_RESET_MBOX		BIT(1)
+#define QCA955X_RESET_I2S		BIT(0)
+
+#define QCA956X_RESET_EXTERNAL		BIT(28)
+#define QCA956X_RESET_FULL_CHIP		BIT(24)
+#define QCA956X_RESET_GE1_MDIO		BIT(23)
+#define QCA956X_RESET_GE0_MDIO		BIT(22)
+#define QCA956X_RESET_CPU_NMI		BIT(21)
+#define QCA956X_RESET_CPU_COLD		BIT(20)
+#define QCA956X_RESET_DMA		BIT(19)
+#define QCA956X_RESET_DDR		BIT(16)
+#define QCA956X_RESET_GE1_MAC		BIT(13)
+#define QCA956X_RESET_SGMII_ANALOG	BIT(12)
+#define QCA956X_RESET_USB_PHY_ANALOG	BIT(11)
+#define QCA956X_RESET_GE0_MAC		BIT(9)
+#define QCA956X_RESET_SGMII		BIT(8)
+#define QCA956X_RESET_USB_HOST		BIT(5)
+#define QCA956X_RESET_USB_PHY		BIT(4)
+#define QCA956X_RESET_USBSUS_OVERRIDE	BIT(3)
+#define QCA956X_RESET_SWITCH_ANALOG	BIT(2)
+#define QCA956X_RESET_SWITCH		BIT(0)
+
+#define AR933X_BOOTSTRAP_MDIO_GPIO_EN	BIT(18)
+#define AR933X_BOOTSTRAP_EEPBUSY	BIT(4)
+#define AR933X_BOOTSTRAP_REF_CLK_40	BIT(0)
+
+#define AR934X_BOOTSTRAP_SW_OPTION8	BIT(23)
+#define AR934X_BOOTSTRAP_SW_OPTION7	BIT(22)
+#define AR934X_BOOTSTRAP_SW_OPTION6	BIT(21)
+#define AR934X_BOOTSTRAP_SW_OPTION5	BIT(20)
+#define AR934X_BOOTSTRAP_SW_OPTION4	BIT(19)
+#define AR934X_BOOTSTRAP_SW_OPTION3	BIT(18)
+#define AR934X_BOOTSTRAP_SW_OPTION2	BIT(17)
+#define AR934X_BOOTSTRAP_SW_OPTION1	BIT(16)
+#define AR934X_BOOTSTRAP_USB_MODE_DEVICE BIT(7)
+#define AR934X_BOOTSTRAP_PCIE_RC	BIT(6)
+#define AR934X_BOOTSTRAP_EJTAG_MODE	BIT(5)
+#define AR934X_BOOTSTRAP_REF_CLK_40	BIT(4)
+#define AR934X_BOOTSTRAP_BOOT_FROM_SPI	BIT(2)
+#define AR934X_BOOTSTRAP_SDRAM_DISABLED BIT(1)
+#define AR934X_BOOTSTRAP_DDR1		BIT(0)
+
+#define QCA953X_BOOTSTRAP_SW_OPTION2	BIT(12)
+#define QCA953X_BOOTSTRAP_SW_OPTION1	BIT(11)
+#define QCA953X_BOOTSTRAP_EJTAG_MODE	BIT(5)
+#define QCA953X_BOOTSTRAP_REF_CLK_40	BIT(4)
+#define QCA953X_BOOTSTRAP_SDRAM_DISABLED BIT(1)
+#define QCA953X_BOOTSTRAP_DDR1		BIT(0)
+
+#define QCA955X_BOOTSTRAP_REF_CLK_40	BIT(4)
+
+#define QCA956X_BOOTSTRAP_REF_CLK_40	BIT(2)
+
+#define AR934X_PCIE_WMAC_INT_WMAC_MISC		BIT(0)
+#define AR934X_PCIE_WMAC_INT_WMAC_TX		BIT(1)
+#define AR934X_PCIE_WMAC_INT_WMAC_RXLP		BIT(2)
+#define AR934X_PCIE_WMAC_INT_WMAC_RXHP		BIT(3)
+#define AR934X_PCIE_WMAC_INT_PCIE_RC		BIT(4)
+#define AR934X_PCIE_WMAC_INT_PCIE_RC0		BIT(5)
+#define AR934X_PCIE_WMAC_INT_PCIE_RC1		BIT(6)
+#define AR934X_PCIE_WMAC_INT_PCIE_RC2		BIT(7)
+#define AR934X_PCIE_WMAC_INT_PCIE_RC3		BIT(8)
+#define AR934X_PCIE_WMAC_INT_WMAC_ALL \
+	(AR934X_PCIE_WMAC_INT_WMAC_MISC | AR934X_PCIE_WMAC_INT_WMAC_TX | \
+	 AR934X_PCIE_WMAC_INT_WMAC_RXLP | AR934X_PCIE_WMAC_INT_WMAC_RXHP)
+
+#define AR934X_PCIE_WMAC_INT_PCIE_ALL \
+	(AR934X_PCIE_WMAC_INT_PCIE_RC | AR934X_PCIE_WMAC_INT_PCIE_RC0 | \
+	 AR934X_PCIE_WMAC_INT_PCIE_RC1 | AR934X_PCIE_WMAC_INT_PCIE_RC2 | \
+	 AR934X_PCIE_WMAC_INT_PCIE_RC3)
+
+#define QCA953X_PCIE_WMAC_INT_WMAC_MISC		BIT(0)
+#define QCA953X_PCIE_WMAC_INT_WMAC_TX		BIT(1)
+#define QCA953X_PCIE_WMAC_INT_WMAC_RXLP		BIT(2)
+#define QCA953X_PCIE_WMAC_INT_WMAC_RXHP		BIT(3)
+#define QCA953X_PCIE_WMAC_INT_PCIE_RC		BIT(4)
+#define QCA953X_PCIE_WMAC_INT_PCIE_RC0		BIT(5)
+#define QCA953X_PCIE_WMAC_INT_PCIE_RC1		BIT(6)
+#define QCA953X_PCIE_WMAC_INT_PCIE_RC2		BIT(7)
+#define QCA953X_PCIE_WMAC_INT_PCIE_RC3		BIT(8)
+#define QCA953X_PCIE_WMAC_INT_WMAC_ALL \
+	(QCA953X_PCIE_WMAC_INT_WMAC_MISC | QCA953X_PCIE_WMAC_INT_WMAC_TX | \
+	 QCA953X_PCIE_WMAC_INT_WMAC_RXLP | QCA953X_PCIE_WMAC_INT_WMAC_RXHP)
+
+#define QCA953X_PCIE_WMAC_INT_PCIE_ALL \
+	(QCA953X_PCIE_WMAC_INT_PCIE_RC | QCA953X_PCIE_WMAC_INT_PCIE_RC0 | \
+	 QCA953X_PCIE_WMAC_INT_PCIE_RC1 | QCA953X_PCIE_WMAC_INT_PCIE_RC2 | \
+	 QCA953X_PCIE_WMAC_INT_PCIE_RC3)
+
+#define QCA955X_EXT_INT_WMAC_MISC		BIT(0)
+#define QCA955X_EXT_INT_WMAC_TX			BIT(1)
+#define QCA955X_EXT_INT_WMAC_RXLP		BIT(2)
+#define QCA955X_EXT_INT_WMAC_RXHP		BIT(3)
+#define QCA955X_EXT_INT_PCIE_RC1		BIT(4)
+#define QCA955X_EXT_INT_PCIE_RC1_INT0		BIT(5)
+#define QCA955X_EXT_INT_PCIE_RC1_INT1		BIT(6)
+#define QCA955X_EXT_INT_PCIE_RC1_INT2		BIT(7)
+#define QCA955X_EXT_INT_PCIE_RC1_INT3		BIT(8)
+#define QCA955X_EXT_INT_PCIE_RC2		BIT(12)
+#define QCA955X_EXT_INT_PCIE_RC2_INT0		BIT(13)
+#define QCA955X_EXT_INT_PCIE_RC2_INT1		BIT(14)
+#define QCA955X_EXT_INT_PCIE_RC2_INT2		BIT(15)
+#define QCA955X_EXT_INT_PCIE_RC2_INT3		BIT(16)
+#define QCA955X_EXT_INT_USB1			BIT(24)
+#define QCA955X_EXT_INT_USB2			BIT(28)
+
+#define QCA955X_EXT_INT_WMAC_ALL \
+	(QCA955X_EXT_INT_WMAC_MISC | QCA955X_EXT_INT_WMAC_TX | \
+	 QCA955X_EXT_INT_WMAC_RXLP | QCA955X_EXT_INT_WMAC_RXHP)
+
+#define QCA955X_EXT_INT_PCIE_RC1_ALL \
+	(QCA955X_EXT_INT_PCIE_RC1 | QCA955X_EXT_INT_PCIE_RC1_INT0 | \
+	 QCA955X_EXT_INT_PCIE_RC1_INT1 | QCA955X_EXT_INT_PCIE_RC1_INT2 | \
+	 QCA955X_EXT_INT_PCIE_RC1_INT3)
+
+#define QCA955X_EXT_INT_PCIE_RC2_ALL \
+	(QCA955X_EXT_INT_PCIE_RC2 | QCA955X_EXT_INT_PCIE_RC2_INT0 | \
+	 QCA955X_EXT_INT_PCIE_RC2_INT1 | QCA955X_EXT_INT_PCIE_RC2_INT2 | \
+	 QCA955X_EXT_INT_PCIE_RC2_INT3)
+
+#define QCA956X_EXT_INT_WMAC_MISC		BIT(0)
+#define QCA956X_EXT_INT_WMAC_TX			BIT(1)
+#define QCA956X_EXT_INT_WMAC_RXLP		BIT(2)
+#define QCA956X_EXT_INT_WMAC_RXHP		BIT(3)
+#define QCA956X_EXT_INT_PCIE_RC1		BIT(4)
+#define QCA956X_EXT_INT_PCIE_RC1_INT0		BIT(5)
+#define QCA956X_EXT_INT_PCIE_RC1_INT1		BIT(6)
+#define QCA956X_EXT_INT_PCIE_RC1_INT2		BIT(7)
+#define QCA956X_EXT_INT_PCIE_RC1_INT3		BIT(8)
+#define QCA956X_EXT_INT_PCIE_RC2		BIT(12)
+#define QCA956X_EXT_INT_PCIE_RC2_INT0		BIT(13)
+#define QCA956X_EXT_INT_PCIE_RC2_INT1		BIT(14)
+#define QCA956X_EXT_INT_PCIE_RC2_INT2		BIT(15)
+#define QCA956X_EXT_INT_PCIE_RC2_INT3		BIT(16)
+#define QCA956X_EXT_INT_USB1			BIT(24)
+#define QCA956X_EXT_INT_USB2			BIT(28)
+
+#define QCA956X_EXT_INT_WMAC_ALL \
+	(QCA956X_EXT_INT_WMAC_MISC | QCA956X_EXT_INT_WMAC_TX | \
+	 QCA956X_EXT_INT_WMAC_RXLP | QCA956X_EXT_INT_WMAC_RXHP)
+
+#define QCA956X_EXT_INT_PCIE_RC1_ALL \
+	(QCA956X_EXT_INT_PCIE_RC1 | QCA956X_EXT_INT_PCIE_RC1_INT0 | \
+	 QCA956X_EXT_INT_PCIE_RC1_INT1 | QCA956X_EXT_INT_PCIE_RC1_INT2 | \
+	 QCA956X_EXT_INT_PCIE_RC1_INT3)
+
+#define QCA956X_EXT_INT_PCIE_RC2_ALL \
+	(QCA956X_EXT_INT_PCIE_RC2 | QCA956X_EXT_INT_PCIE_RC2_INT0 | \
+	 QCA956X_EXT_INT_PCIE_RC2_INT1 | QCA956X_EXT_INT_PCIE_RC2_INT2 | \
+	 QCA956X_EXT_INT_PCIE_RC2_INT3)
+
+#define REV_ID_MAJOR_MASK		0xfff0
+#define REV_ID_MAJOR_AR71XX		0x00a0
+#define REV_ID_MAJOR_AR913X		0x00b0
+#define REV_ID_MAJOR_AR7240		0x00c0
+#define REV_ID_MAJOR_AR7241		0x0100
+#define REV_ID_MAJOR_AR7242		0x1100
+#define REV_ID_MAJOR_AR9330		0x0110
+#define REV_ID_MAJOR_AR9331		0x1110
+#define REV_ID_MAJOR_AR9341		0x0120
+#define REV_ID_MAJOR_AR9342		0x1120
+#define REV_ID_MAJOR_AR9344		0x2120
+#define REV_ID_MAJOR_QCA9533		0x0140
+#define REV_ID_MAJOR_QCA9533_V2		0x0160
+#define REV_ID_MAJOR_QCA9556		0x0130
+#define REV_ID_MAJOR_QCA9558		0x1130
+#define REV_ID_MAJOR_TP9343		0x0150
+#define REV_ID_MAJOR_QCA956X		0x1150
+#define REV_ID_MAJOR_QCN550X		0x2170
+
+#define AR71XX_REV_ID_MINOR_MASK	0x3
+#define AR71XX_REV_ID_MINOR_AR7130	0x0
+#define AR71XX_REV_ID_MINOR_AR7141	0x1
+#define AR71XX_REV_ID_MINOR_AR7161	0x2
+#define AR71XX_REV_ID_REVISION_MASK	0x3
+#define AR71XX_REV_ID_REVISION_SHIFT	2
+
+#define AR913X_REV_ID_MINOR_MASK	0x3
+#define AR913X_REV_ID_MINOR_AR9130	0x0
+#define AR913X_REV_ID_MINOR_AR9132	0x1
+#define AR913X_REV_ID_REVISION_MASK	0x3
+#define AR913X_REV_ID_REVISION_SHIFT	2
+
+#define AR933X_REV_ID_REVISION_MASK	0x3
+
+#define AR724X_REV_ID_REVISION_MASK	0x3
+
+#define AR934X_REV_ID_REVISION_MASK	0xf
+
+#define QCA953X_REV_ID_REVISION_MASK	0xf
+
+#define QCA955X_REV_ID_REVISION_MASK	0xf
+
+#define QCA956X_REV_ID_REVISION_MASK	0xf
+
+/*
+ * SPI block
+ */
+#define AR71XX_SPI_REG_FS	0x00	/* Function Select */
+#define AR71XX_SPI_REG_CTRL	0x04	/* SPI Control */
+#define AR71XX_SPI_REG_IOC	0x08	/* SPI I/O Control */
+#define AR71XX_SPI_REG_RDS	0x0c	/* Read Data Shift */
+
+#define AR71XX_SPI_FS_GPIO	BIT(0)	/* Enable GPIO mode */
+
+#define AR71XX_SPI_CTRL_RD	BIT(6)	/* Remap Disable */
+#define AR71XX_SPI_CTRL_DIV_MASK 0x3f
+
+#define AR71XX_SPI_IOC_DO	BIT(0)	/* Data Out pin */
+#define AR71XX_SPI_IOC_CLK	BIT(8)	/* CLK pin */
+#define AR71XX_SPI_IOC_CS(n)	BIT(16 + (n))
+#define AR71XX_SPI_IOC_CS0	AR71XX_SPI_IOC_CS(0)
+#define AR71XX_SPI_IOC_CS1	AR71XX_SPI_IOC_CS(1)
+#define AR71XX_SPI_IOC_CS2	AR71XX_SPI_IOC_CS(2)
+#define AR71XX_SPI_IOC_CS_ALL	(AR71XX_SPI_IOC_CS0 | AR71XX_SPI_IOC_CS1 | \
+				 AR71XX_SPI_IOC_CS2)
+
+/*
+ * GPIO block
+ */
+#define AR71XX_GPIO_REG_OE		0x00
+#define AR71XX_GPIO_REG_IN		0x04
+#define AR71XX_GPIO_REG_OUT		0x08
+#define AR71XX_GPIO_REG_SET		0x0c
+#define AR71XX_GPIO_REG_CLEAR		0x10
+#define AR71XX_GPIO_REG_INT_MODE	0x14
+#define AR71XX_GPIO_REG_INT_TYPE	0x18
+#define AR71XX_GPIO_REG_INT_POLARITY	0x1c
+#define AR71XX_GPIO_REG_INT_PENDING	0x20
+#define AR71XX_GPIO_REG_INT_ENABLE	0x24
+#define AR71XX_GPIO_REG_FUNC		0x28
+
+#define AR934X_GPIO_REG_OUT_FUNC0	0x2c
+#define AR934X_GPIO_REG_OUT_FUNC1	0x30
+#define AR934X_GPIO_REG_OUT_FUNC2	0x34
+#define AR934X_GPIO_REG_OUT_FUNC3	0x38
+#define AR934X_GPIO_REG_OUT_FUNC4	0x3c
+#define AR934X_GPIO_REG_OUT_FUNC5	0x40
+#define AR934X_GPIO_REG_FUNC		0x6c
+
+#define QCA953X_GPIO_REG_OUT_FUNC0	0x2c
+#define QCA953X_GPIO_REG_OUT_FUNC1	0x30
+#define QCA953X_GPIO_REG_OUT_FUNC2	0x34
+#define QCA953X_GPIO_REG_OUT_FUNC3	0x38
+#define QCA953X_GPIO_REG_OUT_FUNC4	0x3c
+#define QCA953X_GPIO_REG_IN_ENABLE0	0x44
+#define QCA953X_GPIO_REG_FUNC		0x6c
+
+#define QCA953X_GPIO_OUT_MUX_SPI_CS1		10
+#define QCA953X_GPIO_OUT_MUX_SPI_CS2		11
+#define QCA953X_GPIO_OUT_MUX_SPI_CS0		9
+#define QCA953X_GPIO_OUT_MUX_SPI_CLK		8
+#define QCA953X_GPIO_OUT_MUX_SPI_MOSI		12
+#define QCA953X_GPIO_OUT_MUX_LED_LINK1		41
+#define QCA953X_GPIO_OUT_MUX_LED_LINK2		42
+#define QCA953X_GPIO_OUT_MUX_LED_LINK3		43
+#define QCA953X_GPIO_OUT_MUX_LED_LINK4		44
+#define QCA953X_GPIO_OUT_MUX_LED_LINK5		45
+
+#define QCA955X_GPIO_REG_OUT_FUNC0	0x2c
+#define QCA955X_GPIO_REG_OUT_FUNC1	0x30
+#define QCA955X_GPIO_REG_OUT_FUNC2	0x34
+#define QCA955X_GPIO_REG_OUT_FUNC3	0x38
+#define QCA955X_GPIO_REG_OUT_FUNC4	0x3c
+#define QCA955X_GPIO_REG_OUT_FUNC5	0x40
+#define QCA955X_GPIO_REG_FUNC		0x6c
+
+#define QCA956X_GPIO_REG_OUT_FUNC0	0x2c
+#define QCA956X_GPIO_REG_OUT_FUNC1	0x30
+#define QCA956X_GPIO_REG_OUT_FUNC2	0x34
+#define QCA956X_GPIO_REG_OUT_FUNC3	0x38
+#define QCA956X_GPIO_REG_OUT_FUNC4	0x3c
+#define QCA956X_GPIO_REG_OUT_FUNC5	0x40
+#define QCA956X_GPIO_REG_IN_ENABLE0	0x44
+#define QCA956X_GPIO_REG_IN_ENABLE3	0x50
+#define QCA956X_GPIO_REG_FUNC		0x6c
+
+#define QCA956X_GPIO_OUT_MUX_GE0_MDO	32
+#define QCA956X_GPIO_OUT_MUX_GE0_MDC	33
+
+#define AR71XX_GPIO_COUNT		16
+#define AR7240_GPIO_COUNT		18
+#define AR7241_GPIO_COUNT		20
+#define AR913X_GPIO_COUNT		22
+#define AR933X_GPIO_COUNT		30
+#define AR934X_GPIO_COUNT		23
+#define QCA953X_GPIO_COUNT		18
+#define QCA955X_GPIO_COUNT		24
+#define QCA956X_GPIO_COUNT		23
+
+/*
+ * SRIF block
+ */
+#define AR934X_SRIF_CPU_DPLL1_REG	0x1c0
+#define AR934X_SRIF_CPU_DPLL2_REG	0x1c4
+#define AR934X_SRIF_CPU_DPLL3_REG	0x1c8
+
+#define AR934X_SRIF_DDR_DPLL1_REG	0x240
+#define AR934X_SRIF_DDR_DPLL2_REG	0x244
+#define AR934X_SRIF_DDR_DPLL3_REG	0x248
+
+#define AR934X_SRIF_DPLL1_REFDIV_SHIFT	27
+#define AR934X_SRIF_DPLL1_REFDIV_MASK	0x1f
+#define AR934X_SRIF_DPLL1_NINT_SHIFT	18
+#define AR934X_SRIF_DPLL1_NINT_MASK	0x1ff
+#define AR934X_SRIF_DPLL1_NFRAC_MASK	0x0003ffff
+
+#define AR934X_SRIF_DPLL2_LOCAL_PLL	BIT(30)
+#define AR934X_SRIF_DPLL2_OUTDIV_SHIFT	13
+#define AR934X_SRIF_DPLL2_OUTDIV_MASK	0x7
+
+#define QCA953X_SRIF_CPU_DPLL1_REG	0x1c0
+#define QCA953X_SRIF_CPU_DPLL2_REG	0x1c4
+#define QCA953X_SRIF_CPU_DPLL3_REG	0x1c8
+
+#define QCA953X_SRIF_DDR_DPLL1_REG	0x240
+#define QCA953X_SRIF_DDR_DPLL2_REG	0x244
+#define QCA953X_SRIF_DDR_DPLL3_REG	0x248
+
+#define QCA953X_SRIF_DPLL1_REFDIV_SHIFT	27
+#define QCA953X_SRIF_DPLL1_REFDIV_MASK	0x1f
+#define QCA953X_SRIF_DPLL1_NINT_SHIFT	18
+#define QCA953X_SRIF_DPLL1_NINT_MASK	0x1ff
+#define QCA953X_SRIF_DPLL1_NFRAC_MASK	0x0003ffff
+
+#define QCA953X_SRIF_DPLL2_LOCAL_PLL	BIT(30)
+#define QCA953X_SRIF_DPLL2_OUTDIV_SHIFT	13
+#define QCA953X_SRIF_DPLL2_OUTDIV_MASK	0x7
+
+#define AR71XX_GPIO_FUNC_STEREO_EN		BIT(17)
+#define AR71XX_GPIO_FUNC_SLIC_EN		BIT(16)
+#define AR71XX_GPIO_FUNC_SPI_CS2_EN		BIT(13)
+#define AR71XX_GPIO_FUNC_SPI_CS1_EN		BIT(12)
+#define AR71XX_GPIO_FUNC_UART_EN		BIT(8)
+#define AR71XX_GPIO_FUNC_USB_OC_EN		BIT(4)
+#define AR71XX_GPIO_FUNC_USB_CLK_EN		BIT(0)
+
+#define AR724X_GPIO_FUNC_GE0_MII_CLK_EN		BIT(19)
+#define AR724X_GPIO_FUNC_SPI_EN			BIT(18)
+#define AR724X_GPIO_FUNC_SPI_CS_EN2		BIT(14)
+#define AR724X_GPIO_FUNC_SPI_CS_EN1		BIT(13)
+#define AR724X_GPIO_FUNC_CLK_OBS5_EN		BIT(12)
+#define AR724X_GPIO_FUNC_CLK_OBS4_EN		BIT(11)
+#define AR724X_GPIO_FUNC_CLK_OBS3_EN		BIT(10)
+#define AR724X_GPIO_FUNC_CLK_OBS2_EN		BIT(9)
+#define AR724X_GPIO_FUNC_CLK_OBS1_EN		BIT(8)
+#define AR724X_GPIO_FUNC_ETH_SWITCH_LED4_EN	BIT(7)
+#define AR724X_GPIO_FUNC_ETH_SWITCH_LED3_EN	BIT(6)
+#define AR724X_GPIO_FUNC_ETH_SWITCH_LED2_EN	BIT(5)
+#define AR724X_GPIO_FUNC_ETH_SWITCH_LED1_EN	BIT(4)
+#define AR724X_GPIO_FUNC_ETH_SWITCH_LED0_EN	BIT(3)
+#define AR724X_GPIO_FUNC_UART_RTS_CTS_EN	BIT(2)
+#define AR724X_GPIO_FUNC_UART_EN		BIT(1)
+#define AR724X_GPIO_FUNC_JTAG_DISABLE		BIT(0)
+
+#define AR913X_GPIO_FUNC_WMAC_LED_EN		BIT(22)
+#define AR913X_GPIO_FUNC_EXP_PORT_CS_EN		BIT(21)
+#define AR913X_GPIO_FUNC_I2S_REFCLKEN		BIT(20)
+#define AR913X_GPIO_FUNC_I2S_MCKEN		BIT(19)
+#define AR913X_GPIO_FUNC_I2S1_EN		BIT(18)
+#define AR913X_GPIO_FUNC_I2S0_EN		BIT(17)
+#define AR913X_GPIO_FUNC_SLIC_EN		BIT(16)
+#define AR913X_GPIO_FUNC_UART_RTSCTS_EN		BIT(9)
+#define AR913X_GPIO_FUNC_UART_EN		BIT(8)
+#define AR913X_GPIO_FUNC_USB_CLK_EN		BIT(4)
+
+#define AR933X_GPIO_FUNC_SPDIF2TCK		BIT(31)
+#define AR933X_GPIO_FUNC_SPDIF_EN		BIT(30)
+#define AR933X_GPIO_FUNC_I2SO_22_18_EN		BIT(29)
+#define AR933X_GPIO_FUNC_I2S_MCK_EN		BIT(27)
+#define AR933X_GPIO_FUNC_I2SO_EN		BIT(26)
+#define AR933X_GPIO_FUNC_ETH_SWITCH_LED_DUPL	BIT(25)
+#define AR933X_GPIO_FUNC_ETH_SWITCH_LED_COLL	BIT(24)
+#define AR933X_GPIO_FUNC_ETH_SWITCH_LED_ACT	BIT(23)
+#define AR933X_GPIO_FUNC_SPI_EN			BIT(18)
+#define AR933X_GPIO_FUNC_SPI_CS_EN2		BIT(14)
+#define AR933X_GPIO_FUNC_SPI_CS_EN1		BIT(13)
+#define AR933X_GPIO_FUNC_ETH_SWITCH_LED4_EN	BIT(7)
+#define AR933X_GPIO_FUNC_ETH_SWITCH_LED3_EN	BIT(6)
+#define AR933X_GPIO_FUNC_ETH_SWITCH_LED2_EN	BIT(5)
+#define AR933X_GPIO_FUNC_ETH_SWITCH_LED1_EN	BIT(4)
+#define AR933X_GPIO_FUNC_ETH_SWITCH_LED0_EN	BIT(3)
+#define AR933X_GPIO_FUNC_UART_RTS_CTS_EN	BIT(2)
+#define AR933X_GPIO_FUNC_UART_EN		BIT(1)
+#define AR933X_GPIO_FUNC_JTAG_DISABLE		BIT(0)
+
+#define AR934X_GPIO_FUNC_CLK_OBS7_EN		BIT(9)
+#define AR934X_GPIO_FUNC_CLK_OBS6_EN		BIT(8)
+#define AR934X_GPIO_FUNC_CLK_OBS5_EN		BIT(7)
+#define AR934X_GPIO_FUNC_CLK_OBS4_EN		BIT(6)
+#define AR934X_GPIO_FUNC_CLK_OBS3_EN		BIT(5)
+#define AR934X_GPIO_FUNC_CLK_OBS2_EN		BIT(4)
+#define AR934X_GPIO_FUNC_CLK_OBS1_EN		BIT(3)
+#define AR934X_GPIO_FUNC_CLK_OBS0_EN		BIT(2)
+#define AR934X_GPIO_FUNC_JTAG_DISABLE		BIT(1)
+
+#define AR934X_GPIO_OUT_GPIO		0
+#define AR934X_GPIO_OUT_SPI_CS1	7
+#define AR934X_GPIO_OUT_LED_LINK0	41
+#define AR934X_GPIO_OUT_LED_LINK1	42
+#define AR934X_GPIO_OUT_LED_LINK2	43
+#define AR934X_GPIO_OUT_LED_LINK3	44
+#define AR934X_GPIO_OUT_LED_LINK4	45
+#define AR934X_GPIO_OUT_EXT_LNA0	46
+#define AR934X_GPIO_OUT_EXT_LNA1	47
+
+#define QCA955X_GPIO_FUNC_CLK_OBS7_EN		BIT(9)
+#define QCA955X_GPIO_FUNC_CLK_OBS6_EN		BIT(8)
+#define QCA955X_GPIO_FUNC_CLK_OBS5_EN		BIT(7)
+#define QCA955X_GPIO_FUNC_CLK_OBS4_EN		BIT(6)
+#define QCA955X_GPIO_FUNC_CLK_OBS3_EN		BIT(5)
+#define QCA955X_GPIO_FUNC_CLK_OBS2_EN		BIT(4)
+#define QCA955X_GPIO_FUNC_CLK_OBS1_EN		BIT(3)
+#define QCA955X_GPIO_FUNC_JTAG_DISABLE		BIT(1)
+
+#define QCA955X_GPIO_OUT_GPIO		0
+#define QCA955X_MII_EXT_MDI		1
+#define QCA955X_SLIC_DATA_OUT		3
+#define QCA955X_SLIC_PCM_FS		4
+#define QCA955X_SLIC_PCM_CLK		5
+#define QCA955X_SPI_CLK			8
+#define QCA955X_SPI_CS_0		9
+#define QCA955X_SPI_CS_1		10
+#define QCA955X_SPI_CS_2		11
+#define QCA955X_SPI_MISO		12
+#define QCA955X_I2S_CLK			13
+#define QCA955X_I2S_WS			14
+#define QCA955X_I2S_SD			15
+#define QCA955X_I2S_MCK			16
+#define QCA955X_SPDIF_OUT		17
+#define QCA955X_UART1_TD		18
+#define QCA955X_UART1_RTS		19
+#define QCA955X_UART1_RD		20
+#define QCA955X_UART1_CTS		21
+#define QCA955X_UART0_SOUT		22
+#define QCA955X_SPDIF2_OUT		23
+#define QCA955X_LED_SGMII_SPEED0	24
+#define QCA955X_LED_SGMII_SPEED1	25
+#define QCA955X_LED_SGMII_DUPLEX	26
+#define QCA955X_LED_SGMII_LINK_UP	27
+#define QCA955X_SGMII_SPEED0_INVERT	28
+#define QCA955X_SGMII_SPEED1_INVERT	29
+#define QCA955X_SGMII_DUPLEX_INVERT	30
+#define QCA955X_SGMII_LINK_UP_INVERT	31
+#define QCA955X_GE1_MII_MDO		32
+#define QCA955X_GE1_MII_MDC		33
+#define QCA955X_SWCOM2			38
+#define QCA955X_SWCOM3			39
+#define QCA955X_MAC2_GPIO		40
+#define QCA955X_MAC3_GPIO		41
+#define QCA955X_ATT_LED			42
+#define QCA955X_PWR_LED			43
+#define QCA955X_TX_FRAME		44
+#define QCA955X_RX_CLEAR_EXTERNAL	45
+#define QCA955X_LED_NETWORK_EN		46
+#define QCA955X_LED_POWER_EN		47
+#define QCA955X_WMAC_GLUE_WOW		68
+#define QCA955X_RX_CLEAR_EXTENSION	70
+#define QCA955X_CP_NAND_CS1		73
+#define QCA955X_USB_SUSPEND		74
+#define QCA955X_ETH_TX_ERR		75
+#define QCA955X_DDR_DQ_OE		76
+#define QCA955X_CLKREQ_N_EP		77
+#define QCA955X_CLKREQ_N_RC		78
+#define QCA955X_CLK_OBS0		79
+#define QCA955X_CLK_OBS1		80
+#define QCA955X_CLK_OBS2		81
+#define QCA955X_CLK_OBS3		82
+#define QCA955X_CLK_OBS4		83
+#define QCA955X_CLK_OBS5		84
+
+/*
+ * MII_CTRL block
+ */
+#define AR71XX_MII_REG_MII0_CTRL	0x00
+#define AR71XX_MII_REG_MII1_CTRL	0x04
+
+#define AR71XX_MII_CTRL_IF_MASK		3
+#define AR71XX_MII_CTRL_SPEED_SHIFT	4
+#define AR71XX_MII_CTRL_SPEED_MASK	3
+#define AR71XX_MII_CTRL_SPEED_10	0
+#define AR71XX_MII_CTRL_SPEED_100	1
+#define AR71XX_MII_CTRL_SPEED_1000	2
+
+#define AR71XX_MII0_CTRL_IF_GMII	0
+#define AR71XX_MII0_CTRL_IF_MII		1
+#define AR71XX_MII0_CTRL_IF_RGMII	2
+#define AR71XX_MII0_CTRL_IF_RMII	3
+
+#define AR71XX_MII1_CTRL_IF_RGMII	0
+#define AR71XX_MII1_CTRL_IF_RMII	1
+
+/*
+ * AR933X GMAC interface
+ */
+#define AR933X_GMAC_REG_ETH_CFG		0x00
+
+#define AR933X_ETH_CFG_RGMII_GE0	BIT(0)
+#define AR933X_ETH_CFG_MII_GE0		BIT(1)
+#define AR933X_ETH_CFG_GMII_GE0		BIT(2)
+#define AR933X_ETH_CFG_MII_GE0_MASTER	BIT(3)
+#define AR933X_ETH_CFG_MII_GE0_SLAVE	BIT(4)
+#define AR933X_ETH_CFG_MII_GE0_ERR_EN	BIT(5)
+#define AR933X_ETH_CFG_SW_PHY_SWAP	BIT(7)
+#define AR933X_ETH_CFG_SW_PHY_ADDR_SWAP	BIT(8)
+#define AR933X_ETH_CFG_RMII_GE0		BIT(9)
+#define AR933X_ETH_CFG_RMII_GE0_SPD_10	0
+#define AR933X_ETH_CFG_RMII_GE0_SPD_100	BIT(10)
+
+/*
+ * AR934X GMAC Interface
+ */
+#define AR934X_GMAC_REG_ETH_CFG		0x00
+
+#define AR934X_ETH_CFG_RGMII_GMAC0	BIT(0)
+#define AR934X_ETH_CFG_MII_GMAC0	BIT(1)
+#define AR934X_ETH_CFG_GMII_GMAC0	BIT(2)
+#define AR934X_ETH_CFG_MII_GMAC0_MASTER	BIT(3)
+#define AR934X_ETH_CFG_MII_GMAC0_SLAVE	BIT(4)
+#define AR934X_ETH_CFG_MII_GMAC0_ERR_EN	BIT(5)
+#define AR934X_ETH_CFG_SW_ONLY_MODE	BIT(6)
+#define AR934X_ETH_CFG_SW_PHY_SWAP	BIT(7)
+#define AR934X_ETH_CFG_SW_APB_ACCESS	BIT(9)
+#define AR934X_ETH_CFG_RMII_GMAC0	BIT(10)
+#define AR933X_ETH_CFG_MII_CNTL_SPEED	BIT(11)
+#define AR934X_ETH_CFG_RMII_GMAC0_MASTER BIT(12)
+#define AR933X_ETH_CFG_SW_ACC_MSB_FIRST	BIT(13)
+#define AR934X_ETH_CFG_RXD_DELAY        BIT(14)
+#define AR934X_ETH_CFG_RXD_DELAY_MASK   0x3
+#define AR934X_ETH_CFG_RXD_DELAY_SHIFT  14
+#define AR934X_ETH_CFG_RDV_DELAY        BIT(16)
+#define AR934X_ETH_CFG_RDV_DELAY_MASK   0x3
+#define AR934X_ETH_CFG_RDV_DELAY_SHIFT  16
+
+/*
+ * QCA953X GMAC Interface
+ */
+#define QCA953X_GMAC_REG_ETH_CFG		0x00
+
+#define QCA953X_ETH_CFG_SW_ONLY_MODE		BIT(6)
+#define QCA953X_ETH_CFG_SW_PHY_SWAP		BIT(7)
+#define QCA953X_ETH_CFG_SW_APB_ACCESS		BIT(9)
+#define QCA953X_ETH_CFG_SW_ACC_MSB_FIRST	BIT(13)
+
+/*
+ * QCA955X GMAC Interface
+ */
+
+#define QCA955X_GMAC_REG_ETH_CFG	0x00
+#define QCA955X_GMAC_REG_SGMII_SERDES	0x18
+
+#define QCA955X_ETH_CFG_RGMII_EN	BIT(0)
+#define QCA955X_ETH_CFG_MII_GE0		BIT(1)
+#define QCA955X_ETH_CFG_GMII_GE0	BIT(2)
+#define QCA955X_ETH_CFG_MII_GE0_MASTER	BIT(3)
+#define QCA955X_ETH_CFG_MII_GE0_SLAVE	BIT(4)
+#define QCA955X_ETH_CFG_GE0_ERR_EN	BIT(5)
+#define QCA955X_ETH_CFG_GE0_SGMII	BIT(6)
+#define QCA955X_ETH_CFG_RMII_GE0	BIT(10)
+#define QCA955X_ETH_CFG_MII_CNTL_SPEED	BIT(11)
+#define QCA955X_ETH_CFG_RMII_GE0_MASTER	BIT(12)
+#define QCA955X_ETH_CFG_RXD_DELAY_MASK	0x3
+#define QCA955X_ETH_CFG_RXD_DELAY_SHIFT	14
+#define QCA955X_ETH_CFG_RDV_DELAY	BIT(16)
+#define QCA955X_ETH_CFG_RDV_DELAY_MASK	0x3
+#define QCA955X_ETH_CFG_RDV_DELAY_SHIFT	16
+#define QCA955X_ETH_CFG_TXD_DELAY_MASK	0x3
+#define QCA955X_ETH_CFG_TXD_DELAY_SHIFT	18
+#define QCA955X_ETH_CFG_TXE_DELAY_MASK	0x3
+#define QCA955X_ETH_CFG_TXE_DELAY_SHIFT	20
+
+#define QCA955X_SGMII_SERDES_LOCK_DETECT_STATUS	BIT(15)
+#define QCA955X_SGMII_SERDES_RES_CALIBRATION_SHIFT 23
+#define QCA955X_SGMII_SERDES_RES_CALIBRATION_MASK 0xf
+/*
+ * QCA956X GMAC Interface
+ */
+
+#define QCA956X_GMAC_REG_ETH_CFG	0x00
+#define QCA956X_GMAC_REG_SGMII_RESET	0x14
+#define QCA956X_GMAC_REG_SGMII_SERDES	0x18
+#define QCA956X_GMAC_REG_MR_AN_CONTROL	0x1c
+#define QCA956X_GMAC_REG_SGMII_CONFIG	0x34
+#define QCA956X_GMAC_REG_SGMII_DEBUG	0x58
+
+#define QCA956X_ETH_CFG_RGMII_EN		BIT(0)
+#define QCA956X_ETH_CFG_GE0_SGMII		BIT(6)
+#define QCA956X_ETH_CFG_SW_ONLY_MODE		BIT(7)
+#define QCA956X_ETH_CFG_SW_PHY_SWAP		BIT(8)
+#define QCA956X_ETH_CFG_SW_PHY_ADDR_SWAP	BIT(9)
+#define QCA956X_ETH_CFG_SW_APB_ACCESS		BIT(10)
+#define QCA956X_ETH_CFG_SW_ACC_MSB_FIRST	BIT(13)
+#define QCA956X_ETH_CFG_RXD_DELAY_MASK		0x3
+#define QCA956X_ETH_CFG_RXD_DELAY_SHIFT		14
+#define QCA956X_ETH_CFG_RDV_DELAY_MASK		0x3
+#define QCA956X_ETH_CFG_RDV_DELAY_SHIFT		16
+
+#define QCA956X_SGMII_RESET_RX_CLK_N_RESET	0x0
+#define QCA956X_SGMII_RESET_RX_CLK_N		BIT(0)
+#define QCA956X_SGMII_RESET_TX_CLK_N		BIT(1)
+#define QCA956X_SGMII_RESET_RX_125M_N		BIT(2)
+#define QCA956X_SGMII_RESET_TX_125M_N		BIT(3)
+#define QCA956X_SGMII_RESET_HW_RX_125M_N	BIT(4)
+
+#define QCA956X_SGMII_SERDES_CDR_BW_MASK	0x3
+#define QCA956X_SGMII_SERDES_CDR_BW_SHIFT	1
+#define QCA956X_SGMII_SERDES_TX_DR_CTRL_MASK	0x7
+#define QCA956X_SGMII_SERDES_TX_DR_CTRL_SHIFT	4
+#define QCA956X_SGMII_SERDES_PLL_BW		BIT(8)
+#define QCA956X_SGMII_SERDES_VCO_FAST		BIT(9)
+#define QCA956X_SGMII_SERDES_VCO_SLOW		BIT(10)
+#define QCA956X_SGMII_SERDES_LOCK_DETECT_STATUS	BIT(15)
+#define QCA956X_SGMII_SERDES_EN_SIGNAL_DETECT	BIT(16)
+#define QCA956X_SGMII_SERDES_FIBER_SDO		BIT(17)
+#define QCA956X_SGMII_SERDES_RES_CALIBRATION_SHIFT 23
+#define QCA956X_SGMII_SERDES_RES_CALIBRATION_MASK 0xf
+#define QCA956X_SGMII_SERDES_VCO_REG_SHIFT	27
+#define QCA956X_SGMII_SERDES_VCO_REG_MASK	0xf
+
+#define QCA956X_MR_AN_CONTROL_AN_ENABLE		BIT(12)
+#define QCA956X_MR_AN_CONTROL_PHY_RESET		BIT(15)
+
+#define QCA956X_SGMII_CONFIG_MODE_CTRL_SHIFT	0
+#define QCA956X_SGMII_CONFIG_MODE_CTRL_MASK	0x7
+
+#endif /* __ASM_MACH_AR71XX_REGS_H */
diff --git a/arch/mips/include/asm/mach-ath79/ar933x_uart.h b/arch/mips/include/asm/mach-ath79/ar933x_uart.h
new file mode 100644
index 000000000..cacf3545e
--- /dev/null
+++ b/arch/mips/include/asm/mach-ath79/ar933x_uart.h
@@ -0,0 +1,64 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *  Atheros AR933X UART defines
+ *
+ *  Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
+ */
+
+#ifndef __AR933X_UART_H
+#define __AR933X_UART_H
+
+#define AR933X_UART_REGS_SIZE		20
+#define AR933X_UART_FIFO_SIZE		16
+
+#define AR933X_UART_DATA_REG		0x00
+#define AR933X_UART_CS_REG		0x04
+#define AR933X_UART_CLOCK_REG		0x08
+#define AR933X_UART_INT_REG		0x0c
+#define AR933X_UART_INT_EN_REG		0x10
+
+#define AR933X_UART_DATA_TX_RX_MASK	0xff
+#define AR933X_UART_DATA_RX_CSR		BIT(8)
+#define AR933X_UART_DATA_TX_CSR		BIT(9)
+
+#define AR933X_UART_CS_PARITY_S		0
+#define AR933X_UART_CS_PARITY_M		0x3
+#define	  AR933X_UART_CS_PARITY_NONE	0
+#define	  AR933X_UART_CS_PARITY_ODD	2
+#define	  AR933X_UART_CS_PARITY_EVEN	3
+#define AR933X_UART_CS_IF_MODE_S	2
+#define AR933X_UART_CS_IF_MODE_M	0x3
+#define	  AR933X_UART_CS_IF_MODE_NONE	0
+#define	  AR933X_UART_CS_IF_MODE_DTE	1
+#define	  AR933X_UART_CS_IF_MODE_DCE	2
+#define AR933X_UART_CS_FLOW_CTRL_S	4
+#define AR933X_UART_CS_FLOW_CTRL_M	0x3
+#define AR933X_UART_CS_DMA_EN		BIT(6)
+#define AR933X_UART_CS_TX_READY_ORIDE	BIT(7)
+#define AR933X_UART_CS_RX_READY_ORIDE	BIT(8)
+#define AR933X_UART_CS_TX_READY		BIT(9)
+#define AR933X_UART_CS_RX_BREAK		BIT(10)
+#define AR933X_UART_CS_TX_BREAK		BIT(11)
+#define AR933X_UART_CS_HOST_INT		BIT(12)
+#define AR933X_UART_CS_HOST_INT_EN	BIT(13)
+#define AR933X_UART_CS_TX_BUSY		BIT(14)
+#define AR933X_UART_CS_RX_BUSY		BIT(15)
+
+#define AR933X_UART_CLOCK_STEP_M	0xffff
+#define AR933X_UART_CLOCK_SCALE_M	0xfff
+#define AR933X_UART_CLOCK_SCALE_S	16
+#define AR933X_UART_CLOCK_STEP_M	0xffff
+
+#define AR933X_UART_INT_RX_VALID	BIT(0)
+#define AR933X_UART_INT_TX_READY	BIT(1)
+#define AR933X_UART_INT_RX_FRAMING_ERR	BIT(2)
+#define AR933X_UART_INT_RX_OFLOW_ERR	BIT(3)
+#define AR933X_UART_INT_TX_OFLOW_ERR	BIT(4)
+#define AR933X_UART_INT_RX_PARITY_ERR	BIT(5)
+#define AR933X_UART_INT_RX_BREAK_ON	BIT(6)
+#define AR933X_UART_INT_RX_BREAK_OFF	BIT(7)
+#define AR933X_UART_INT_RX_FULL		BIT(8)
+#define AR933X_UART_INT_TX_EMPTY	BIT(9)
+#define AR933X_UART_INT_ALLINTS		0x3ff
+
+#endif /* __AR933X_UART_H */
diff --git a/arch/mips/include/asm/mach-ath79/ath79.h b/arch/mips/include/asm/mach-ath79/ath79.h
new file mode 100644
index 000000000..70cda7449
--- /dev/null
+++ b/arch/mips/include/asm/mach-ath79/ath79.h
@@ -0,0 +1,178 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *  Atheros AR71XX/AR724X/AR913X common definitions
+ *
+ *  Copyright (C) 2008-2011 Gabor Juhos <juhosg@openwrt.org>
+ *  Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ *
+ *  Parts of this file are based on Atheros' 2.6.15 BSP
+ */
+
+#ifndef __ASM_MACH_ATH79_H
+#define __ASM_MACH_ATH79_H
+
+#include <linux/types.h>
+#include <linux/io.h>
+
+enum ath79_soc_type {
+	ATH79_SOC_UNKNOWN,
+	ATH79_SOC_AR7130,
+	ATH79_SOC_AR7141,
+	ATH79_SOC_AR7161,
+	ATH79_SOC_AR7240,
+	ATH79_SOC_AR7241,
+	ATH79_SOC_AR7242,
+	ATH79_SOC_AR9130,
+	ATH79_SOC_AR9132,
+	ATH79_SOC_AR9330,
+	ATH79_SOC_AR9331,
+	ATH79_SOC_AR9341,
+	ATH79_SOC_AR9342,
+	ATH79_SOC_AR9344,
+	ATH79_SOC_QCA9533,
+	ATH79_SOC_QCA9556,
+	ATH79_SOC_QCA9558,
+	ATH79_SOC_TP9343,
+	ATH79_SOC_QCA956X,
+};
+
+extern enum ath79_soc_type ath79_soc;
+extern unsigned int ath79_soc_rev;
+
+static inline int soc_is_ar71xx(void)
+{
+	return (ath79_soc == ATH79_SOC_AR7130 ||
+		ath79_soc == ATH79_SOC_AR7141 ||
+		ath79_soc == ATH79_SOC_AR7161);
+}
+
+static inline int soc_is_ar724x(void)
+{
+	return (ath79_soc == ATH79_SOC_AR7240 ||
+		ath79_soc == ATH79_SOC_AR7241 ||
+		ath79_soc == ATH79_SOC_AR7242);
+}
+
+static inline int soc_is_ar7240(void)
+{
+	return (ath79_soc == ATH79_SOC_AR7240);
+}
+
+static inline int soc_is_ar7241(void)
+{
+	return (ath79_soc == ATH79_SOC_AR7241);
+}
+
+static inline int soc_is_ar7242(void)
+{
+	return (ath79_soc == ATH79_SOC_AR7242);
+}
+
+static inline int soc_is_ar913x(void)
+{
+	return (ath79_soc == ATH79_SOC_AR9130 ||
+		ath79_soc == ATH79_SOC_AR9132);
+}
+
+static inline int soc_is_ar933x(void)
+{
+	return (ath79_soc == ATH79_SOC_AR9330 ||
+		ath79_soc == ATH79_SOC_AR9331);
+}
+
+static inline int soc_is_ar9341(void)
+{
+	return (ath79_soc == ATH79_SOC_AR9341);
+}
+
+static inline int soc_is_ar9342(void)
+{
+	return (ath79_soc == ATH79_SOC_AR9342);
+}
+
+static inline int soc_is_ar9344(void)
+{
+	return (ath79_soc == ATH79_SOC_AR9344);
+}
+
+static inline int soc_is_ar934x(void)
+{
+	return soc_is_ar9341() || soc_is_ar9342() || soc_is_ar9344();
+}
+
+static inline int soc_is_qca9533(void)
+{
+	return ath79_soc == ATH79_SOC_QCA9533;
+}
+
+static inline int soc_is_qca953x(void)
+{
+	return soc_is_qca9533();
+}
+
+static inline int soc_is_qca9556(void)
+{
+	return ath79_soc == ATH79_SOC_QCA9556;
+}
+
+static inline int soc_is_qca9558(void)
+{
+	return ath79_soc == ATH79_SOC_QCA9558;
+}
+
+static inline int soc_is_qca955x(void)
+{
+	return soc_is_qca9556() || soc_is_qca9558();
+}
+
+static inline int soc_is_tp9343(void)
+{
+	return ath79_soc == ATH79_SOC_TP9343;
+}
+
+static inline int soc_is_qca9561(void)
+{
+	return ath79_soc == ATH79_SOC_QCA956X;
+}
+
+static inline int soc_is_qca9563(void)
+{
+	return ath79_soc == ATH79_SOC_QCA956X;
+}
+
+static inline int soc_is_qca956x(void)
+{
+	return soc_is_qca9561() || soc_is_qca9563();
+}
+
+void ath79_ddr_wb_flush(unsigned int reg);
+void ath79_ddr_set_pci_windows(void);
+
+extern void __iomem *ath79_pll_base;
+extern void __iomem *ath79_reset_base;
+
+static inline void ath79_pll_wr(unsigned reg, u32 val)
+{
+	__raw_writel(val, ath79_pll_base + reg);
+}
+
+static inline u32 ath79_pll_rr(unsigned reg)
+{
+	return __raw_readl(ath79_pll_base + reg);
+}
+
+static inline void ath79_reset_wr(unsigned reg, u32 val)
+{
+	__raw_writel(val, ath79_reset_base + reg);
+	(void) __raw_readl(ath79_reset_base + reg); /* flush */
+}
+
+static inline u32 ath79_reset_rr(unsigned reg)
+{
+	return __raw_readl(ath79_reset_base + reg);
+}
+
+void ath79_device_reset_set(u32 mask);
+void ath79_device_reset_clear(u32 mask);
+
+#endif /* __ASM_MACH_ATH79_H */
diff --git a/arch/mips/include/asm/mach-ath79/cpu-feature-overrides.h b/arch/mips/include/asm/mach-ath79/cpu-feature-overrides.h
new file mode 100644
index 000000000..44fd44a5f
--- /dev/null
+++ b/arch/mips/include/asm/mach-ath79/cpu-feature-overrides.h
@@ -0,0 +1,55 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *  Atheros AR71XX/AR724X/AR913X specific CPU feature overrides
+ *
+ *  Copyright (C) 2008-2010 Gabor Juhos <juhosg@openwrt.org>
+ *  Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ *
+ *  This file was derived from: include/asm-mips/cpu-features.h
+ *	Copyright (C) 2003, 2004 Ralf Baechle
+ *	Copyright (C) 2004 Maciej W. Rozycki
+ */
+#ifndef __ASM_MACH_ATH79_CPU_FEATURE_OVERRIDES_H
+#define __ASM_MACH_ATH79_CPU_FEATURE_OVERRIDES_H
+
+#define cpu_has_tlb		1
+#define cpu_has_4kex		1
+#define cpu_has_3k_cache	0
+#define cpu_has_4k_cache	1
+#define cpu_has_sb1_cache	0
+#define cpu_has_fpu		0
+#define cpu_has_32fpr		0
+#define cpu_has_counter		1
+#define cpu_has_watch		1
+#define cpu_has_divec		1
+
+#define cpu_has_prefetch	1
+#define cpu_has_ejtag		1
+#define cpu_has_llsc		1
+
+#define cpu_has_mips16		1
+#define cpu_has_mdmx		0
+#define cpu_has_mips3d		0
+#define cpu_has_smartmips	0
+#define cpu_has_rixi		0
+
+#define cpu_has_mips32r1	1
+#define cpu_has_mips32r2	1
+#define cpu_has_mips64r1	0
+#define cpu_has_mips64r2	0
+
+#define cpu_has_mipsmt		0
+#define cpu_has_userlocal	0
+
+#define cpu_has_64bits		0
+#define cpu_has_64bit_zero_reg	0
+#define cpu_has_64bit_gp_regs	0
+
+#define cpu_dcache_line_size()	32
+#define cpu_icache_line_size()	32
+#define cpu_has_vtag_icache	0
+#define cpu_has_dc_aliases	1
+#define cpu_has_ic_fills_f_dc	0
+#define cpu_has_pindexed_dcache	0
+
+#endif /* __ASM_MACH_ATH79_CPU_FEATURE_OVERRIDES_H */
diff --git a/arch/mips/include/asm/mach-ath79/irq.h b/arch/mips/include/asm/mach-ath79/irq.h
new file mode 100644
index 000000000..882534be0
--- /dev/null
+++ b/arch/mips/include/asm/mach-ath79/irq.h
@@ -0,0 +1,32 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *  Copyright (C) 2008-2010 Gabor Juhos <juhosg@openwrt.org>
+ *  Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ */
+#ifndef __ASM_MACH_ATH79_IRQ_H
+#define __ASM_MACH_ATH79_IRQ_H
+
+#define MIPS_CPU_IRQ_BASE	0
+#define NR_IRQS			51
+
+#define ATH79_CPU_IRQ(_x)	(MIPS_CPU_IRQ_BASE + (_x))
+
+#define ATH79_MISC_IRQ_BASE	8
+#define ATH79_MISC_IRQ_COUNT	32
+#define ATH79_MISC_IRQ(_x)	(ATH79_MISC_IRQ_BASE + (_x))
+
+#define ATH79_PCI_IRQ_BASE	(ATH79_MISC_IRQ_BASE + ATH79_MISC_IRQ_COUNT)
+#define ATH79_PCI_IRQ_COUNT	6
+#define ATH79_PCI_IRQ(_x)	(ATH79_PCI_IRQ_BASE + (_x))
+
+#define ATH79_IP2_IRQ_BASE	(ATH79_PCI_IRQ_BASE + ATH79_PCI_IRQ_COUNT)
+#define ATH79_IP2_IRQ_COUNT	2
+#define ATH79_IP2_IRQ(_x)	(ATH79_IP2_IRQ_BASE + (_x))
+
+#define ATH79_IP3_IRQ_BASE	(ATH79_IP2_IRQ_BASE + ATH79_IP2_IRQ_COUNT)
+#define ATH79_IP3_IRQ_COUNT     3
+#define ATH79_IP3_IRQ(_x)       (ATH79_IP3_IRQ_BASE + (_x))
+
+#include <asm/mach-generic/irq.h>
+
+#endif /* __ASM_MACH_ATH79_IRQ_H */
diff --git a/arch/mips/include/asm/mach-ath79/kernel-entry-init.h b/arch/mips/include/asm/mach-ath79/kernel-entry-init.h
new file mode 100644
index 000000000..88db67bf4
--- /dev/null
+++ b/arch/mips/include/asm/mach-ath79/kernel-entry-init.h
@@ -0,0 +1,28 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *  Atheros AR71XX/AR724X/AR913X specific kernel entry setup
+ *
+ *  Copyright (C) 2009 Gabor Juhos <juhosg@openwrt.org>
+ */
+#ifndef __ASM_MACH_ATH79_KERNEL_ENTRY_H
+#define __ASM_MACH_ATH79_KERNEL_ENTRY_H
+
+	/*
+	 * Some bootloaders set the 'Kseg0 coherency algorithm' to
+	 * 'Cacheable, noncoherent, write-through, no write allocate'
+	 * and this cause performance issues. Let's go and change it to
+	 * 'Cacheable, noncoherent, write-back, write allocate'
+	 */
+	.macro	kernel_entry_setup
+	mfc0	t0, CP0_CONFIG
+	li	t1, ~CONF_CM_CMASK
+	and	t0, t1
+	ori	t0, CONF_CM_CACHABLE_NONCOHERENT
+	mtc0	t0, CP0_CONFIG
+	nop
+	.endm
+
+	.macro	smp_slave_setup
+	.endm
+
+#endif /* __ASM_MACH_ATH79_KERNEL_ENTRY_H */
diff --git a/arch/mips/include/asm/mach-au1x00/au1000.h b/arch/mips/include/asm/mach-au1x00/au1000.h
new file mode 100644
index 000000000..a7eec3364
--- /dev/null
+++ b/arch/mips/include/asm/mach-au1x00/au1000.h
@@ -0,0 +1,1211 @@
+/*
+ *
+ * BRIEF MODULE DESCRIPTION
+ *	Include file for Alchemy Semiconductor's Au1k CPU.
+ *
+ * Copyright 2000-2001, 2006-2008 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc. <source@mvista.com>
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+ /*
+  * some definitions add by takuzo@sm.sony.co.jp and sato@sm.sony.co.jp
+  */
+
+#ifndef _AU1000_H_
+#define _AU1000_H_
+
+/* SOC Interrupt numbers */
+/* Au1000-style (IC0/1): 2 controllers with 32 sources each */
+#define AU1000_INTC0_INT_BASE	(MIPS_CPU_IRQ_BASE + 8)
+#define AU1000_INTC0_INT_LAST	(AU1000_INTC0_INT_BASE + 31)
+#define AU1000_INTC1_INT_BASE	(AU1000_INTC0_INT_LAST + 1)
+#define AU1000_INTC1_INT_LAST	(AU1000_INTC1_INT_BASE + 31)
+#define AU1000_MAX_INTR		AU1000_INTC1_INT_LAST
+
+/* Au1300-style (GPIC): 1 controller with up to 128 sources */
+#define ALCHEMY_GPIC_INT_BASE	(MIPS_CPU_IRQ_BASE + 8)
+#define ALCHEMY_GPIC_INT_NUM	128
+#define ALCHEMY_GPIC_INT_LAST	(ALCHEMY_GPIC_INT_BASE + ALCHEMY_GPIC_INT_NUM - 1)
+
+/* common clock names, shared among all variants. AUXPLL2 is Au1300 */
+#define ALCHEMY_ROOT_CLK		"root_clk"
+#define ALCHEMY_CPU_CLK			"cpu_clk"
+#define ALCHEMY_AUXPLL_CLK		"auxpll_clk"
+#define ALCHEMY_AUXPLL2_CLK		"auxpll2_clk"
+#define ALCHEMY_SYSBUS_CLK		"sysbus_clk"
+#define ALCHEMY_PERIPH_CLK		"periph_clk"
+#define ALCHEMY_MEM_CLK			"mem_clk"
+#define ALCHEMY_LR_CLK			"lr_clk"
+#define ALCHEMY_FG0_CLK			"fg0_clk"
+#define ALCHEMY_FG1_CLK			"fg1_clk"
+#define ALCHEMY_FG2_CLK			"fg2_clk"
+#define ALCHEMY_FG3_CLK			"fg3_clk"
+#define ALCHEMY_FG4_CLK			"fg4_clk"
+#define ALCHEMY_FG5_CLK			"fg5_clk"
+
+/* Au1300 peripheral interrupt numbers */
+#define AU1300_FIRST_INT	(ALCHEMY_GPIC_INT_BASE)
+#define AU1300_UART1_INT	(AU1300_FIRST_INT + 17)
+#define AU1300_UART2_INT	(AU1300_FIRST_INT + 25)
+#define AU1300_UART3_INT	(AU1300_FIRST_INT + 27)
+#define AU1300_SD1_INT		(AU1300_FIRST_INT + 32)
+#define AU1300_SD2_INT		(AU1300_FIRST_INT + 38)
+#define AU1300_PSC0_INT		(AU1300_FIRST_INT + 48)
+#define AU1300_PSC1_INT		(AU1300_FIRST_INT + 52)
+#define AU1300_PSC2_INT		(AU1300_FIRST_INT + 56)
+#define AU1300_PSC3_INT		(AU1300_FIRST_INT + 60)
+#define AU1300_NAND_INT		(AU1300_FIRST_INT + 62)
+#define AU1300_DDMA_INT		(AU1300_FIRST_INT + 75)
+#define AU1300_MMU_INT		(AU1300_FIRST_INT + 76)
+#define AU1300_MPU_INT		(AU1300_FIRST_INT + 77)
+#define AU1300_GPU_INT		(AU1300_FIRST_INT + 78)
+#define AU1300_UDMA_INT		(AU1300_FIRST_INT + 79)
+#define AU1300_TOY_INT		(AU1300_FIRST_INT + 80)
+#define AU1300_TOY_MATCH0_INT	(AU1300_FIRST_INT + 81)
+#define AU1300_TOY_MATCH1_INT	(AU1300_FIRST_INT + 82)
+#define AU1300_TOY_MATCH2_INT	(AU1300_FIRST_INT + 83)
+#define AU1300_RTC_INT		(AU1300_FIRST_INT + 84)
+#define AU1300_RTC_MATCH0_INT	(AU1300_FIRST_INT + 85)
+#define AU1300_RTC_MATCH1_INT	(AU1300_FIRST_INT + 86)
+#define AU1300_RTC_MATCH2_INT	(AU1300_FIRST_INT + 87)
+#define AU1300_UART0_INT	(AU1300_FIRST_INT + 88)
+#define AU1300_SD0_INT		(AU1300_FIRST_INT + 89)
+#define AU1300_USB_INT		(AU1300_FIRST_INT + 90)
+#define AU1300_LCD_INT		(AU1300_FIRST_INT + 91)
+#define AU1300_BSA_INT		(AU1300_FIRST_INT + 92)
+#define AU1300_MPE_INT		(AU1300_FIRST_INT + 93)
+#define AU1300_ITE_INT		(AU1300_FIRST_INT + 94)
+#define AU1300_AES_INT		(AU1300_FIRST_INT + 95)
+#define AU1300_CIM_INT		(AU1300_FIRST_INT + 96)
+
+/**********************************************************************/
+
+/*
+ * Physical base addresses for integrated peripherals
+ * 0..au1000 1..au1500 2..au1100 3..au1550 4..au1200 5..au1300
+ */
+
+#define AU1000_AC97_PHYS_ADDR		0x10000000 /* 012 */
+#define AU1300_ROM_PHYS_ADDR		0x10000000 /* 5 */
+#define AU1300_OTP_PHYS_ADDR		0x10002000 /* 5 */
+#define AU1300_VSS_PHYS_ADDR		0x10003000 /* 5 */
+#define AU1300_UART0_PHYS_ADDR		0x10100000 /* 5 */
+#define AU1300_UART1_PHYS_ADDR		0x10101000 /* 5 */
+#define AU1300_UART2_PHYS_ADDR		0x10102000 /* 5 */
+#define AU1300_UART3_PHYS_ADDR		0x10103000 /* 5 */
+#define AU1000_USB_OHCI_PHYS_ADDR	0x10100000 /* 012 */
+#define AU1000_USB_UDC_PHYS_ADDR	0x10200000 /* 0123 */
+#define AU1300_GPIC_PHYS_ADDR		0x10200000 /* 5 */
+#define AU1000_IRDA_PHYS_ADDR		0x10300000 /* 02 */
+#define AU1200_AES_PHYS_ADDR		0x10300000 /* 45 */
+#define AU1000_IC0_PHYS_ADDR		0x10400000 /* 01234 */
+#define AU1300_GPU_PHYS_ADDR		0x10500000 /* 5 */
+#define AU1000_MAC0_PHYS_ADDR		0x10500000 /* 023 */
+#define AU1000_MAC1_PHYS_ADDR		0x10510000 /* 023 */
+#define AU1000_MACEN_PHYS_ADDR		0x10520000 /* 023 */
+#define AU1100_SD0_PHYS_ADDR		0x10600000 /* 245 */
+#define AU1300_SD1_PHYS_ADDR		0x10601000 /* 5 */
+#define AU1300_SD2_PHYS_ADDR		0x10602000 /* 5 */
+#define AU1100_SD1_PHYS_ADDR		0x10680000 /* 24 */
+#define AU1300_SYS_PHYS_ADDR		0x10900000 /* 5 */
+#define AU1550_PSC2_PHYS_ADDR		0x10A00000 /* 3 */
+#define AU1550_PSC3_PHYS_ADDR		0x10B00000 /* 3 */
+#define AU1300_PSC0_PHYS_ADDR		0x10A00000 /* 5 */
+#define AU1300_PSC1_PHYS_ADDR		0x10A01000 /* 5 */
+#define AU1300_PSC2_PHYS_ADDR		0x10A02000 /* 5 */
+#define AU1300_PSC3_PHYS_ADDR		0x10A03000 /* 5 */
+#define AU1000_I2S_PHYS_ADDR		0x11000000 /* 02 */
+#define AU1500_MAC0_PHYS_ADDR		0x11500000 /* 1 */
+#define AU1500_MAC1_PHYS_ADDR		0x11510000 /* 1 */
+#define AU1500_MACEN_PHYS_ADDR		0x11520000 /* 1 */
+#define AU1000_UART0_PHYS_ADDR		0x11100000 /* 01234 */
+#define AU1200_SWCNT_PHYS_ADDR		0x1110010C /* 4 */
+#define AU1000_UART1_PHYS_ADDR		0x11200000 /* 0234 */
+#define AU1000_UART2_PHYS_ADDR		0x11300000 /* 0 */
+#define AU1000_UART3_PHYS_ADDR		0x11400000 /* 0123 */
+#define AU1000_SSI0_PHYS_ADDR		0x11600000 /* 02 */
+#define AU1000_SSI1_PHYS_ADDR		0x11680000 /* 02 */
+#define AU1500_GPIO2_PHYS_ADDR		0x11700000 /* 1234 */
+#define AU1000_IC1_PHYS_ADDR		0x11800000 /* 01234 */
+#define AU1000_SYS_PHYS_ADDR		0x11900000 /* 012345 */
+#define AU1550_PSC0_PHYS_ADDR		0x11A00000 /* 34 */
+#define AU1550_PSC1_PHYS_ADDR		0x11B00000 /* 34 */
+#define AU1000_MEM_PHYS_ADDR		0x14000000 /* 01234 */
+#define AU1000_STATIC_MEM_PHYS_ADDR	0x14001000 /* 01234 */
+#define AU1300_UDMA_PHYS_ADDR		0x14001800 /* 5 */
+#define AU1000_DMA_PHYS_ADDR		0x14002000 /* 012 */
+#define AU1550_DBDMA_PHYS_ADDR		0x14002000 /* 345 */
+#define AU1550_DBDMA_CONF_PHYS_ADDR	0x14003000 /* 345 */
+#define AU1000_MACDMA0_PHYS_ADDR	0x14004000 /* 0123 */
+#define AU1000_MACDMA1_PHYS_ADDR	0x14004200 /* 0123 */
+#define AU1200_CIM_PHYS_ADDR		0x14004000 /* 45 */
+#define AU1500_PCI_PHYS_ADDR		0x14005000 /* 13 */
+#define AU1550_PE_PHYS_ADDR		0x14008000 /* 3 */
+#define AU1200_MAEBE_PHYS_ADDR		0x14010000 /* 4 */
+#define AU1200_MAEFE_PHYS_ADDR		0x14012000 /* 4 */
+#define AU1300_MAEITE_PHYS_ADDR		0x14010000 /* 5 */
+#define AU1300_MAEMPE_PHYS_ADDR		0x14014000 /* 5 */
+#define AU1550_USB_OHCI_PHYS_ADDR	0x14020000 /* 3 */
+#define AU1200_USB_CTL_PHYS_ADDR	0x14020000 /* 4 */
+#define AU1200_USB_OTG_PHYS_ADDR	0x14020020 /* 4 */
+#define AU1200_USB_OHCI_PHYS_ADDR	0x14020100 /* 4 */
+#define AU1200_USB_EHCI_PHYS_ADDR	0x14020200 /* 4 */
+#define AU1200_USB_UDC_PHYS_ADDR	0x14022000 /* 4 */
+#define AU1300_USB_EHCI_PHYS_ADDR	0x14020000 /* 5 */
+#define AU1300_USB_OHCI0_PHYS_ADDR	0x14020400 /* 5 */
+#define AU1300_USB_OHCI1_PHYS_ADDR	0x14020800 /* 5 */
+#define AU1300_USB_CTL_PHYS_ADDR	0x14021000 /* 5 */
+#define AU1300_USB_OTG_PHYS_ADDR	0x14022000 /* 5 */
+#define AU1300_MAEBSA_PHYS_ADDR		0x14030000 /* 5 */
+#define AU1100_LCD_PHYS_ADDR		0x15000000 /* 2 */
+#define AU1200_LCD_PHYS_ADDR		0x15000000 /* 45 */
+#define AU1500_PCI_MEM_PHYS_ADDR	0x400000000ULL /* 13 */
+#define AU1500_PCI_IO_PHYS_ADDR		0x500000000ULL /* 13 */
+#define AU1500_PCI_CONFIG0_PHYS_ADDR	0x600000000ULL /* 13 */
+#define AU1500_PCI_CONFIG1_PHYS_ADDR	0x680000000ULL /* 13 */
+#define AU1000_PCMCIA_IO_PHYS_ADDR	0xF00000000ULL /* 012345 */
+#define AU1000_PCMCIA_ATTR_PHYS_ADDR	0xF40000000ULL /* 012345 */
+#define AU1000_PCMCIA_MEM_PHYS_ADDR	0xF80000000ULL /* 012345 */
+
+/**********************************************************************/
+
+
+/*
+ * Au1300 GPIO+INT controller (GPIC) register offsets and bits
+ * Registers are 128bits (0x10 bytes), divided into 4 "banks".
+ */
+#define AU1300_GPIC_PINVAL	0x0000
+#define AU1300_GPIC_PINVALCLR	0x0010
+#define AU1300_GPIC_IPEND	0x0020
+#define AU1300_GPIC_PRIENC	0x0030
+#define AU1300_GPIC_IEN		0x0040	/* int_mask in manual */
+#define AU1300_GPIC_IDIS	0x0050	/* int_maskclr in manual */
+#define AU1300_GPIC_DMASEL	0x0060
+#define AU1300_GPIC_DEVSEL	0x0080
+#define AU1300_GPIC_DEVCLR	0x0090
+#define AU1300_GPIC_RSTVAL	0x00a0
+/* pin configuration space. one 32bit register for up to 128 IRQs */
+#define AU1300_GPIC_PINCFG	0x1000
+
+#define GPIC_GPIO_TO_BIT(gpio)	\
+	(1 << ((gpio) & 0x1f))
+
+#define GPIC_GPIO_BANKOFF(gpio) \
+	(((gpio) >> 5) * 4)
+
+/* Pin Control bits: who owns the pin, what does it do */
+#define GPIC_CFG_PC_GPIN		0
+#define GPIC_CFG_PC_DEV			1
+#define GPIC_CFG_PC_GPOLOW		2
+#define GPIC_CFG_PC_GPOHIGH		3
+#define GPIC_CFG_PC_MASK		3
+
+/* assign pin to MIPS IRQ line */
+#define GPIC_CFG_IL_SET(x)	(((x) & 3) << 2)
+#define GPIC_CFG_IL_MASK	(3 << 2)
+
+/* pin interrupt type setup */
+#define GPIC_CFG_IC_OFF		(0 << 4)
+#define GPIC_CFG_IC_LEVEL_LOW	(1 << 4)
+#define GPIC_CFG_IC_LEVEL_HIGH	(2 << 4)
+#define GPIC_CFG_IC_EDGE_FALL	(5 << 4)
+#define GPIC_CFG_IC_EDGE_RISE	(6 << 4)
+#define GPIC_CFG_IC_EDGE_BOTH	(7 << 4)
+#define GPIC_CFG_IC_MASK	(7 << 4)
+
+/* allow interrupt to wake cpu from 'wait' */
+#define GPIC_CFG_IDLEWAKE	(1 << 7)
+
+/***********************************************************************/
+
+/* Au1000 SDRAM memory controller register offsets */
+#define AU1000_MEM_SDMODE0		0x0000
+#define AU1000_MEM_SDMODE1		0x0004
+#define AU1000_MEM_SDMODE2		0x0008
+#define AU1000_MEM_SDADDR0		0x000C
+#define AU1000_MEM_SDADDR1		0x0010
+#define AU1000_MEM_SDADDR2		0x0014
+#define AU1000_MEM_SDREFCFG		0x0018
+#define AU1000_MEM_SDPRECMD		0x001C
+#define AU1000_MEM_SDAUTOREF		0x0020
+#define AU1000_MEM_SDWRMD0		0x0024
+#define AU1000_MEM_SDWRMD1		0x0028
+#define AU1000_MEM_SDWRMD2		0x002C
+#define AU1000_MEM_SDSLEEP		0x0030
+#define AU1000_MEM_SDSMCKE		0x0034
+
+/* MEM_SDMODE register content definitions */
+#define MEM_SDMODE_F		(1 << 22)
+#define MEM_SDMODE_SR		(1 << 21)
+#define MEM_SDMODE_BS		(1 << 20)
+#define MEM_SDMODE_RS		(3 << 18)
+#define MEM_SDMODE_CS		(7 << 15)
+#define MEM_SDMODE_TRAS		(15 << 11)
+#define MEM_SDMODE_TMRD		(3 << 9)
+#define MEM_SDMODE_TWR		(3 << 7)
+#define MEM_SDMODE_TRP		(3 << 5)
+#define MEM_SDMODE_TRCD		(3 << 3)
+#define MEM_SDMODE_TCL		(7 << 0)
+
+#define MEM_SDMODE_BS_2Bank	(0 << 20)
+#define MEM_SDMODE_BS_4Bank	(1 << 20)
+#define MEM_SDMODE_RS_11Row	(0 << 18)
+#define MEM_SDMODE_RS_12Row	(1 << 18)
+#define MEM_SDMODE_RS_13Row	(2 << 18)
+#define MEM_SDMODE_RS_N(N)	((N) << 18)
+#define MEM_SDMODE_CS_7Col	(0 << 15)
+#define MEM_SDMODE_CS_8Col	(1 << 15)
+#define MEM_SDMODE_CS_9Col	(2 << 15)
+#define MEM_SDMODE_CS_10Col	(3 << 15)
+#define MEM_SDMODE_CS_11Col	(4 << 15)
+#define MEM_SDMODE_CS_N(N)	((N) << 15)
+#define MEM_SDMODE_TRAS_N(N)	((N) << 11)
+#define MEM_SDMODE_TMRD_N(N)	((N) << 9)
+#define MEM_SDMODE_TWR_N(N)	((N) << 7)
+#define MEM_SDMODE_TRP_N(N)	((N) << 5)
+#define MEM_SDMODE_TRCD_N(N)	((N) << 3)
+#define MEM_SDMODE_TCL_N(N)	((N) << 0)
+
+/* MEM_SDADDR register contents definitions */
+#define MEM_SDADDR_E		(1 << 20)
+#define MEM_SDADDR_CSBA		(0x03FF << 10)
+#define MEM_SDADDR_CSMASK	(0x03FF << 0)
+#define MEM_SDADDR_CSBA_N(N)	((N) & (0x03FF << 22) >> 12)
+#define MEM_SDADDR_CSMASK_N(N)	((N)&(0x03FF << 22) >> 22)
+
+/* MEM_SDREFCFG register content definitions */
+#define MEM_SDREFCFG_TRC	(15 << 28)
+#define MEM_SDREFCFG_TRPM	(3 << 26)
+#define MEM_SDREFCFG_E		(1 << 25)
+#define MEM_SDREFCFG_RE		(0x1ffffff << 0)
+#define MEM_SDREFCFG_TRC_N(N)	((N) << MEM_SDREFCFG_TRC)
+#define MEM_SDREFCFG_TRPM_N(N)	((N) << MEM_SDREFCFG_TRPM)
+#define MEM_SDREFCFG_REF_N(N)	(N)
+
+/* Au1550 SDRAM Register Offsets */
+#define AU1550_MEM_SDMODE0		0x0800
+#define AU1550_MEM_SDMODE1		0x0808
+#define AU1550_MEM_SDMODE2		0x0810
+#define AU1550_MEM_SDADDR0		0x0820
+#define AU1550_MEM_SDADDR1		0x0828
+#define AU1550_MEM_SDADDR2		0x0830
+#define AU1550_MEM_SDCONFIGA		0x0840
+#define AU1550_MEM_SDCONFIGB		0x0848
+#define AU1550_MEM_SDSTAT		0x0850
+#define AU1550_MEM_SDERRADDR		0x0858
+#define AU1550_MEM_SDSTRIDE0		0x0860
+#define AU1550_MEM_SDSTRIDE1		0x0868
+#define AU1550_MEM_SDSTRIDE2		0x0870
+#define AU1550_MEM_SDWRMD0		0x0880
+#define AU1550_MEM_SDWRMD1		0x0888
+#define AU1550_MEM_SDWRMD2		0x0890
+#define AU1550_MEM_SDPRECMD		0x08C0
+#define AU1550_MEM_SDAUTOREF		0x08C8
+#define AU1550_MEM_SDSREF		0x08D0
+#define AU1550_MEM_SDSLEEP		MEM_SDSREF
+
+/* Static Bus Controller register offsets */
+#define AU1000_MEM_STCFG0	0x000
+#define AU1000_MEM_STTIME0	0x004
+#define AU1000_MEM_STADDR0	0x008
+#define AU1000_MEM_STCFG1	0x010
+#define AU1000_MEM_STTIME1	0x014
+#define AU1000_MEM_STADDR1	0x018
+#define AU1000_MEM_STCFG2	0x020
+#define AU1000_MEM_STTIME2	0x024
+#define AU1000_MEM_STADDR2	0x028
+#define AU1000_MEM_STCFG3	0x030
+#define AU1000_MEM_STTIME3	0x034
+#define AU1000_MEM_STADDR3	0x038
+#define AU1000_MEM_STNDCTL	0x100
+#define AU1000_MEM_STSTAT	0x104
+
+#define MEM_STNAND_CMD		0x0
+#define MEM_STNAND_ADDR		0x4
+#define MEM_STNAND_DATA		0x20
+
+
+/* Programmable Counters 0 and 1 */
+#define AU1000_SYS_CNTRCTRL	0x14
+#  define SYS_CNTRL_E1S		(1 << 23)
+#  define SYS_CNTRL_T1S		(1 << 20)
+#  define SYS_CNTRL_M21		(1 << 19)
+#  define SYS_CNTRL_M11		(1 << 18)
+#  define SYS_CNTRL_M01		(1 << 17)
+#  define SYS_CNTRL_C1S		(1 << 16)
+#  define SYS_CNTRL_BP		(1 << 14)
+#  define SYS_CNTRL_EN1		(1 << 13)
+#  define SYS_CNTRL_BT1		(1 << 12)
+#  define SYS_CNTRL_EN0		(1 << 11)
+#  define SYS_CNTRL_BT0		(1 << 10)
+#  define SYS_CNTRL_E0		(1 << 8)
+#  define SYS_CNTRL_E0S		(1 << 7)
+#  define SYS_CNTRL_32S		(1 << 5)
+#  define SYS_CNTRL_T0S		(1 << 4)
+#  define SYS_CNTRL_M20		(1 << 3)
+#  define SYS_CNTRL_M10		(1 << 2)
+#  define SYS_CNTRL_M00		(1 << 1)
+#  define SYS_CNTRL_C0S		(1 << 0)
+
+/* Programmable Counter 0 Registers */
+#define AU1000_SYS_TOYTRIM	0x00
+#define AU1000_SYS_TOYWRITE	0x04
+#define AU1000_SYS_TOYMATCH0	0x08
+#define AU1000_SYS_TOYMATCH1	0x0c
+#define AU1000_SYS_TOYMATCH2	0x10
+#define AU1000_SYS_TOYREAD	0x40
+
+/* Programmable Counter 1 Registers */
+#define AU1000_SYS_RTCTRIM	0x44
+#define AU1000_SYS_RTCWRITE	0x48
+#define AU1000_SYS_RTCMATCH0	0x4c
+#define AU1000_SYS_RTCMATCH1	0x50
+#define AU1000_SYS_RTCMATCH2	0x54
+#define AU1000_SYS_RTCREAD	0x58
+
+
+/* GPIO */
+#define AU1000_SYS_PINFUNC	0x2C
+#  define SYS_PF_USB		(1 << 15)	/* 2nd USB device/host */
+#  define SYS_PF_U3		(1 << 14)	/* GPIO23/U3TXD */
+#  define SYS_PF_U2		(1 << 13)	/* GPIO22/U2TXD */
+#  define SYS_PF_U1		(1 << 12)	/* GPIO21/U1TXD */
+#  define SYS_PF_SRC		(1 << 11)	/* GPIO6/SROMCKE */
+#  define SYS_PF_CK5		(1 << 10)	/* GPIO3/CLK5 */
+#  define SYS_PF_CK4		(1 << 9)	/* GPIO2/CLK4 */
+#  define SYS_PF_IRF		(1 << 8)	/* GPIO15/IRFIRSEL */
+#  define SYS_PF_UR3		(1 << 7)	/* GPIO[14:9]/UART3 */
+#  define SYS_PF_I2D		(1 << 6)	/* GPIO8/I2SDI */
+#  define SYS_PF_I2S		(1 << 5)	/* I2S/GPIO[29:31] */
+#  define SYS_PF_NI2		(1 << 4)	/* NI2/GPIO[24:28] */
+#  define SYS_PF_U0		(1 << 3)	/* U0TXD/GPIO20 */
+#  define SYS_PF_RD		(1 << 2)	/* IRTXD/GPIO19 */
+#  define SYS_PF_A97		(1 << 1)	/* AC97/SSL1 */
+#  define SYS_PF_S0		(1 << 0)	/* SSI_0/GPIO[16:18] */
+
+/* Au1100 only */
+#  define SYS_PF_PC		(1 << 18)	/* PCMCIA/GPIO[207:204] */
+#  define SYS_PF_LCD		(1 << 17)	/* extern lcd/GPIO[203:200] */
+#  define SYS_PF_CS		(1 << 16)	/* EXTCLK0/32KHz to gpio2 */
+#  define SYS_PF_EX0		(1 << 9)	/* GPIO2/clock */
+
+/* Au1550 only.	 Redefines lots of pins */
+#  define SYS_PF_PSC2_MASK	(7 << 17)
+#  define SYS_PF_PSC2_AC97	0
+#  define SYS_PF_PSC2_SPI	0
+#  define SYS_PF_PSC2_I2S	(1 << 17)
+#  define SYS_PF_PSC2_SMBUS	(3 << 17)
+#  define SYS_PF_PSC2_GPIO	(7 << 17)
+#  define SYS_PF_PSC3_MASK	(7 << 20)
+#  define SYS_PF_PSC3_AC97	0
+#  define SYS_PF_PSC3_SPI	0
+#  define SYS_PF_PSC3_I2S	(1 << 20)
+#  define SYS_PF_PSC3_SMBUS	(3 << 20)
+#  define SYS_PF_PSC3_GPIO	(7 << 20)
+#  define SYS_PF_PSC1_S1	(1 << 1)
+#  define SYS_PF_MUST_BE_SET	((1 << 5) | (1 << 2))
+
+/* Au1200 only */
+#define SYS_PINFUNC_DMA		(1 << 31)
+#define SYS_PINFUNC_S0A		(1 << 30)
+#define SYS_PINFUNC_S1A		(1 << 29)
+#define SYS_PINFUNC_LP0		(1 << 28)
+#define SYS_PINFUNC_LP1		(1 << 27)
+#define SYS_PINFUNC_LD16	(1 << 26)
+#define SYS_PINFUNC_LD8		(1 << 25)
+#define SYS_PINFUNC_LD1		(1 << 24)
+#define SYS_PINFUNC_LD0		(1 << 23)
+#define SYS_PINFUNC_P1A		(3 << 21)
+#define SYS_PINFUNC_P1B		(1 << 20)
+#define SYS_PINFUNC_FS3		(1 << 19)
+#define SYS_PINFUNC_P0A		(3 << 17)
+#define SYS_PINFUNC_CS		(1 << 16)
+#define SYS_PINFUNC_CIM		(1 << 15)
+#define SYS_PINFUNC_P1C		(1 << 14)
+#define SYS_PINFUNC_U1T		(1 << 12)
+#define SYS_PINFUNC_U1R		(1 << 11)
+#define SYS_PINFUNC_EX1		(1 << 10)
+#define SYS_PINFUNC_EX0		(1 << 9)
+#define SYS_PINFUNC_U0R		(1 << 8)
+#define SYS_PINFUNC_MC		(1 << 7)
+#define SYS_PINFUNC_S0B		(1 << 6)
+#define SYS_PINFUNC_S0C		(1 << 5)
+#define SYS_PINFUNC_P0B		(1 << 4)
+#define SYS_PINFUNC_U0T		(1 << 3)
+#define SYS_PINFUNC_S1B		(1 << 2)
+
+/* Power Management */
+#define AU1000_SYS_SCRATCH0	0x18
+#define AU1000_SYS_SCRATCH1	0x1c
+#define AU1000_SYS_WAKEMSK	0x34
+#define AU1000_SYS_ENDIAN	0x38
+#define AU1000_SYS_POWERCTRL	0x3c
+#define AU1000_SYS_WAKESRC	0x5c
+#define AU1000_SYS_SLPPWR	0x78
+#define AU1000_SYS_SLEEP	0x7c
+
+#define SYS_WAKEMSK_D2		(1 << 9)
+#define SYS_WAKEMSK_M2		(1 << 8)
+#define SYS_WAKEMSK_GPIO(x)	(1 << (x))
+
+/* Clock Controller */
+#define AU1000_SYS_FREQCTRL0	0x20
+#define AU1000_SYS_FREQCTRL1	0x24
+#define AU1000_SYS_CLKSRC	0x28
+#define AU1000_SYS_CPUPLL	0x60
+#define AU1000_SYS_AUXPLL	0x64
+#define AU1300_SYS_AUXPLL2	0x68
+
+
+/**********************************************************************/
+
+
+/* The PCI chip selects are outside the 32bit space, and since we can't
+ * just program the 36bit addresses into BARs, we have to take a chunk
+ * out of the 32bit space and reserve it for PCI.  When these addresses
+ * are ioremap()ed, they'll be fixed up to the real 36bit address before
+ * being passed to the real ioremap function.
+ */
+#define ALCHEMY_PCI_MEMWIN_START	(AU1500_PCI_MEM_PHYS_ADDR >> 4)
+#define ALCHEMY_PCI_MEMWIN_END		(ALCHEMY_PCI_MEMWIN_START + 0x0FFFFFFF)
+
+/* for PCI IO it's simpler because we get to do the ioremap ourselves and then
+ * adjust the device's resources.
+ */
+#define ALCHEMY_PCI_IOWIN_START		0x00001000
+#define ALCHEMY_PCI_IOWIN_END		0x0000FFFF
+
+#ifdef CONFIG_PCI
+
+#define IOPORT_RESOURCE_START	0x00001000	/* skip legacy probing */
+#define IOPORT_RESOURCE_END	0xffffffff
+#define IOMEM_RESOURCE_START	0x10000000
+#define IOMEM_RESOURCE_END	0xfffffffffULL
+
+#else
+
+/* Don't allow any legacy ports probing */
+#define IOPORT_RESOURCE_START	0x10000000
+#define IOPORT_RESOURCE_END	0xffffffff
+#define IOMEM_RESOURCE_START	0x10000000
+#define IOMEM_RESOURCE_END	0xfffffffffULL
+
+#endif
+
+/* PCI controller block register offsets */
+#define PCI_REG_CMEM		0x0000
+#define PCI_REG_CONFIG		0x0004
+#define PCI_REG_B2BMASK_CCH	0x0008
+#define PCI_REG_B2BBASE0_VID	0x000C
+#define PCI_REG_B2BBASE1_SID	0x0010
+#define PCI_REG_MWMASK_DEV	0x0014
+#define PCI_REG_MWBASE_REV_CCL	0x0018
+#define PCI_REG_ERR_ADDR	0x001C
+#define PCI_REG_SPEC_INTACK	0x0020
+#define PCI_REG_ID		0x0100
+#define PCI_REG_STATCMD		0x0104
+#define PCI_REG_CLASSREV	0x0108
+#define PCI_REG_PARAM		0x010C
+#define PCI_REG_MBAR		0x0110
+#define PCI_REG_TIMEOUT		0x0140
+
+/* PCI controller block register bits */
+#define PCI_CMEM_E		(1 << 28)	/* enable cacheable memory */
+#define PCI_CMEM_CMBASE(x)	(((x) & 0x3fff) << 14)
+#define PCI_CMEM_CMMASK(x)	((x) & 0x3fff)
+#define PCI_CONFIG_ERD		(1 << 27) /* pci error during R/W */
+#define PCI_CONFIG_ET		(1 << 26) /* error in target mode */
+#define PCI_CONFIG_EF		(1 << 25) /* fatal error */
+#define PCI_CONFIG_EP		(1 << 24) /* parity error */
+#define PCI_CONFIG_EM		(1 << 23) /* multiple errors */
+#define PCI_CONFIG_BM		(1 << 22) /* bad master error */
+#define PCI_CONFIG_PD		(1 << 20) /* PCI Disable */
+#define PCI_CONFIG_BME		(1 << 19) /* Byte Mask Enable for reads */
+#define PCI_CONFIG_NC		(1 << 16) /* mark mem access non-coherent */
+#define PCI_CONFIG_IA		(1 << 15) /* INTA# enabled (target mode) */
+#define PCI_CONFIG_IP		(1 << 13) /* int on PCI_PERR# */
+#define PCI_CONFIG_IS		(1 << 12) /* int on PCI_SERR# */
+#define PCI_CONFIG_IMM		(1 << 11) /* int on master abort */
+#define PCI_CONFIG_ITM		(1 << 10) /* int on target abort (as master) */
+#define PCI_CONFIG_ITT		(1 << 9)  /* int on target abort (as target) */
+#define PCI_CONFIG_IPB		(1 << 8)  /* int on PERR# in bus master acc */
+#define PCI_CONFIG_SIC_NO	(0 << 6)  /* no byte mask changes */
+#define PCI_CONFIG_SIC_BA_ADR	(1 << 6)  /* on byte/hw acc, invert adr bits */
+#define PCI_CONFIG_SIC_HWA_DAT	(2 << 6)  /* on halfword acc, swap data */
+#define PCI_CONFIG_SIC_ALL	(3 << 6)  /* swap data bytes on all accesses */
+#define PCI_CONFIG_ST		(1 << 5)  /* swap data by target transactions */
+#define PCI_CONFIG_SM		(1 << 4)  /* swap data from PCI ctl */
+#define PCI_CONFIG_AEN		(1 << 3)  /* enable internal arbiter */
+#define PCI_CONFIG_R2H		(1 << 2)  /* REQ2# to hi-prio arbiter */
+#define PCI_CONFIG_R1H		(1 << 1)  /* REQ1# to hi-prio arbiter */
+#define PCI_CONFIG_CH		(1 << 0)  /* PCI ctl to hi-prio arbiter */
+#define PCI_B2BMASK_B2BMASK(x)	(((x) & 0xffff) << 16)
+#define PCI_B2BMASK_CCH(x)	((x) & 0xffff) /* 16 upper bits of class code */
+#define PCI_B2BBASE0_VID_B0(x)	(((x) & 0xffff) << 16)
+#define PCI_B2BBASE0_VID_SV(x)	((x) & 0xffff)
+#define PCI_B2BBASE1_SID_B1(x)	(((x) & 0xffff) << 16)
+#define PCI_B2BBASE1_SID_SI(x)	((x) & 0xffff)
+#define PCI_MWMASKDEV_MWMASK(x) (((x) & 0xffff) << 16)
+#define PCI_MWMASKDEV_DEVID(x)	((x) & 0xffff)
+#define PCI_MWBASEREVCCL_BASE(x) (((x) & 0xffff) << 16)
+#define PCI_MWBASEREVCCL_REV(x)	 (((x) & 0xff) << 8)
+#define PCI_MWBASEREVCCL_CCL(x)	 ((x) & 0xff)
+#define PCI_ID_DID(x)		(((x) & 0xffff) << 16)
+#define PCI_ID_VID(x)		((x) & 0xffff)
+#define PCI_STATCMD_STATUS(x)	(((x) & 0xffff) << 16)
+#define PCI_STATCMD_CMD(x)	((x) & 0xffff)
+#define PCI_CLASSREV_CLASS(x)	(((x) & 0x00ffffff) << 8)
+#define PCI_CLASSREV_REV(x)	((x) & 0xff)
+#define PCI_PARAM_BIST(x)	(((x) & 0xff) << 24)
+#define PCI_PARAM_HT(x)		(((x) & 0xff) << 16)
+#define PCI_PARAM_LT(x)		(((x) & 0xff) << 8)
+#define PCI_PARAM_CLS(x)	((x) & 0xff)
+#define PCI_TIMEOUT_RETRIES(x)	(((x) & 0xff) << 8)	/* max retries */
+#define PCI_TIMEOUT_TO(x)	((x) & 0xff)	/* target ready timeout */
+
+
+/**********************************************************************/
+
+
+#ifndef _LANGUAGE_ASSEMBLY
+
+#include <linux/delay.h>
+#include <linux/types.h>
+
+#include <linux/io.h>
+#include <linux/irq.h>
+
+#include <asm/cpu.h>
+
+/* helpers to access the SYS_* registers */
+static inline unsigned long alchemy_rdsys(int regofs)
+{
+	void __iomem *b = (void __iomem *)KSEG1ADDR(AU1000_SYS_PHYS_ADDR);
+
+	return __raw_readl(b + regofs);
+}
+
+static inline void alchemy_wrsys(unsigned long v, int regofs)
+{
+	void __iomem *b = (void __iomem *)KSEG1ADDR(AU1000_SYS_PHYS_ADDR);
+
+	__raw_writel(v, b + regofs);
+	wmb(); /* drain writebuffer */
+}
+
+/* helpers to access static memctrl registers */
+static inline unsigned long alchemy_rdsmem(int regofs)
+{
+	void __iomem *b = (void __iomem *)KSEG1ADDR(AU1000_STATIC_MEM_PHYS_ADDR);
+
+	return __raw_readl(b + regofs);
+}
+
+static inline void alchemy_wrsmem(unsigned long v, int regofs)
+{
+	void __iomem *b = (void __iomem *)KSEG1ADDR(AU1000_STATIC_MEM_PHYS_ADDR);
+
+	__raw_writel(v, b + regofs);
+	wmb(); /* drain writebuffer */
+}
+
+/* Early Au1000 have a write-only SYS_CPUPLL register. */
+static inline int au1xxx_cpu_has_pll_wo(void)
+{
+	switch (read_c0_prid()) {
+	case 0x00030100:	/* Au1000 DA */
+	case 0x00030201:	/* Au1000 HA */
+	case 0x00030202:	/* Au1000 HB */
+		return 1;
+	}
+	return 0;
+}
+
+/* does CPU need CONFIG[OD] set to fix tons of errata? */
+static inline int au1xxx_cpu_needs_config_od(void)
+{
+	/*
+	 * c0_config.od (bit 19) was write only (and read as 0) on the
+	 * early revisions of Alchemy SOCs.  It disables the bus trans-
+	 * action overlapping and needs to be set to fix various errata.
+	 */
+	switch (read_c0_prid()) {
+	case 0x00030100: /* Au1000 DA */
+	case 0x00030201: /* Au1000 HA */
+	case 0x00030202: /* Au1000 HB */
+	case 0x01030200: /* Au1500 AB */
+	/*
+	 * Au1100/Au1200 errata actually keep silence about this bit,
+	 * so we set it just in case for those revisions that require
+	 * it to be set according to the (now gone) cpu_table.
+	 */
+	case 0x02030200: /* Au1100 AB */
+	case 0x02030201: /* Au1100 BA */
+	case 0x02030202: /* Au1100 BC */
+	case 0x04030201: /* Au1200 AC */
+		return 1;
+	}
+	return 0;
+}
+
+#define ALCHEMY_CPU_UNKNOWN	-1
+#define ALCHEMY_CPU_AU1000	0
+#define ALCHEMY_CPU_AU1500	1
+#define ALCHEMY_CPU_AU1100	2
+#define ALCHEMY_CPU_AU1550	3
+#define ALCHEMY_CPU_AU1200	4
+#define ALCHEMY_CPU_AU1300	5
+
+static inline int alchemy_get_cputype(void)
+{
+	switch (read_c0_prid() & (PRID_OPT_MASK | PRID_COMP_MASK)) {
+	case 0x00030000:
+		return ALCHEMY_CPU_AU1000;
+		break;
+	case 0x01030000:
+		return ALCHEMY_CPU_AU1500;
+		break;
+	case 0x02030000:
+		return ALCHEMY_CPU_AU1100;
+		break;
+	case 0x03030000:
+		return ALCHEMY_CPU_AU1550;
+		break;
+	case 0x04030000:
+	case 0x05030000:
+		return ALCHEMY_CPU_AU1200;
+		break;
+	case 0x800c0000:
+		return ALCHEMY_CPU_AU1300;
+		break;
+	}
+
+	return ALCHEMY_CPU_UNKNOWN;
+}
+
+/* return number of uarts on a given cputype */
+static inline int alchemy_get_uarts(int type)
+{
+	switch (type) {
+	case ALCHEMY_CPU_AU1000:
+	case ALCHEMY_CPU_AU1300:
+		return 4;
+	case ALCHEMY_CPU_AU1500:
+	case ALCHEMY_CPU_AU1200:
+		return 2;
+	case ALCHEMY_CPU_AU1100:
+	case ALCHEMY_CPU_AU1550:
+		return 3;
+	}
+	return 0;
+}
+
+/* enable an UART block if it isn't already */
+static inline void alchemy_uart_enable(u32 uart_phys)
+{
+	void __iomem *addr = (void __iomem *)KSEG1ADDR(uart_phys);
+
+	/* reset, enable clock, deassert reset */
+	if ((__raw_readl(addr + 0x100) & 3) != 3) {
+		__raw_writel(0, addr + 0x100);
+		wmb(); /* drain writebuffer */
+		__raw_writel(1, addr + 0x100);
+		wmb(); /* drain writebuffer */
+	}
+	__raw_writel(3, addr + 0x100);
+	wmb(); /* drain writebuffer */
+}
+
+static inline void alchemy_uart_disable(u32 uart_phys)
+{
+	void __iomem *addr = (void __iomem *)KSEG1ADDR(uart_phys);
+
+	__raw_writel(0, addr + 0x100);	/* UART_MOD_CNTRL */
+	wmb(); /* drain writebuffer */
+}
+
+static inline void alchemy_uart_putchar(u32 uart_phys, u8 c)
+{
+	void __iomem *base = (void __iomem *)KSEG1ADDR(uart_phys);
+	int timeout, i;
+
+	/* check LSR TX_EMPTY bit */
+	timeout = 0xffffff;
+	do {
+		if (__raw_readl(base + 0x1c) & 0x20)
+			break;
+		/* slow down */
+		for (i = 10000; i; i--)
+			asm volatile ("nop");
+	} while (--timeout);
+
+	__raw_writel(c, base + 0x04);	/* tx */
+	wmb(); /* drain writebuffer */
+}
+
+/* return number of ethernet MACs on a given cputype */
+static inline int alchemy_get_macs(int type)
+{
+	switch (type) {
+	case ALCHEMY_CPU_AU1000:
+	case ALCHEMY_CPU_AU1500:
+	case ALCHEMY_CPU_AU1550:
+		return 2;
+	case ALCHEMY_CPU_AU1100:
+		return 1;
+	}
+	return 0;
+}
+
+/* PM: arch/mips/alchemy/common/sleeper.S, power.c, irq.c */
+void alchemy_sleep_au1000(void);
+void alchemy_sleep_au1550(void);
+void alchemy_sleep_au1300(void);
+void au_sleep(void);
+
+/* USB: arch/mips/alchemy/common/usb.c */
+enum alchemy_usb_block {
+	ALCHEMY_USB_OHCI0,
+	ALCHEMY_USB_UDC0,
+	ALCHEMY_USB_EHCI0,
+	ALCHEMY_USB_OTG0,
+	ALCHEMY_USB_OHCI1,
+};
+int alchemy_usb_control(int block, int enable);
+
+/* PCI controller platform data */
+struct alchemy_pci_platdata {
+	int (*board_map_irq)(const struct pci_dev *d, u8 slot, u8 pin);
+	int (*board_pci_idsel)(unsigned int devsel, int assert);
+	/* bits to set/clear in PCI_CONFIG register */
+	unsigned long pci_cfg_set;
+	unsigned long pci_cfg_clr;
+};
+
+/* The IrDA peripheral has an IRFIRSEL pin, but on the DB/PB boards it's
+ * not used to select FIR/SIR mode on the transceiver but as a GPIO.
+ * Instead a CPLD has to be told about the mode.  The driver calls the
+ * set_phy_mode() function in addition to driving the IRFIRSEL pin.
+ */
+#define AU1000_IRDA_PHY_MODE_OFF	0
+#define AU1000_IRDA_PHY_MODE_SIR	1
+#define AU1000_IRDA_PHY_MODE_FIR	2
+
+struct au1k_irda_platform_data {
+	void (*set_phy_mode)(int mode);
+};
+
+
+/* Multifunction pins: Each of these pins can either be assigned to the
+ * GPIO controller or a on-chip peripheral.
+ * Call "au1300_pinfunc_to_dev()" or "au1300_pinfunc_to_gpio()" to
+ * assign one of these to either the GPIO controller or the device.
+ */
+enum au1300_multifunc_pins {
+	/* wake-from-str pins 0-3 */
+	AU1300_PIN_WAKE0 = 0, AU1300_PIN_WAKE1, AU1300_PIN_WAKE2,
+	AU1300_PIN_WAKE3,
+	/* external clock sources for PSCs: 4-5 */
+	AU1300_PIN_EXTCLK0, AU1300_PIN_EXTCLK1,
+	/* 8bit MMC interface on SD0: 6-9 */
+	AU1300_PIN_SD0DAT4, AU1300_PIN_SD0DAT5, AU1300_PIN_SD0DAT6,
+	AU1300_PIN_SD0DAT7,
+	/* aux clk input for freqgen 3: 10 */
+	AU1300_PIN_FG3AUX,
+	/* UART1 pins: 11-18 */
+	AU1300_PIN_U1RI, AU1300_PIN_U1DCD, AU1300_PIN_U1DSR,
+	AU1300_PIN_U1CTS, AU1300_PIN_U1RTS, AU1300_PIN_U1DTR,
+	AU1300_PIN_U1RX, AU1300_PIN_U1TX,
+	/* UART0 pins: 19-24 */
+	AU1300_PIN_U0RI, AU1300_PIN_U0DCD, AU1300_PIN_U0DSR,
+	AU1300_PIN_U0CTS, AU1300_PIN_U0RTS, AU1300_PIN_U0DTR,
+	/* UART2: 25-26 */
+	AU1300_PIN_U2RX, AU1300_PIN_U2TX,
+	/* UART3: 27-28 */
+	AU1300_PIN_U3RX, AU1300_PIN_U3TX,
+	/* LCD controller PWMs, ext pixclock: 29-31 */
+	AU1300_PIN_LCDPWM0, AU1300_PIN_LCDPWM1, AU1300_PIN_LCDCLKIN,
+	/* SD1 interface: 32-37 */
+	AU1300_PIN_SD1DAT0, AU1300_PIN_SD1DAT1, AU1300_PIN_SD1DAT2,
+	AU1300_PIN_SD1DAT3, AU1300_PIN_SD1CMD, AU1300_PIN_SD1CLK,
+	/* SD2 interface: 38-43 */
+	AU1300_PIN_SD2DAT0, AU1300_PIN_SD2DAT1, AU1300_PIN_SD2DAT2,
+	AU1300_PIN_SD2DAT3, AU1300_PIN_SD2CMD, AU1300_PIN_SD2CLK,
+	/* PSC0/1 clocks: 44-45 */
+	AU1300_PIN_PSC0CLK, AU1300_PIN_PSC1CLK,
+	/* PSCs: 46-49/50-53/54-57/58-61 */
+	AU1300_PIN_PSC0SYNC0, AU1300_PIN_PSC0SYNC1, AU1300_PIN_PSC0D0,
+	AU1300_PIN_PSC0D1,
+	AU1300_PIN_PSC1SYNC0, AU1300_PIN_PSC1SYNC1, AU1300_PIN_PSC1D0,
+	AU1300_PIN_PSC1D1,
+	AU1300_PIN_PSC2SYNC0, AU1300_PIN_PSC2SYNC1, AU1300_PIN_PSC2D0,
+	AU1300_PIN_PSC2D1,
+	AU1300_PIN_PSC3SYNC0, AU1300_PIN_PSC3SYNC1, AU1300_PIN_PSC3D0,
+	AU1300_PIN_PSC3D1,
+	/* PCMCIA interface: 62-70 */
+	AU1300_PIN_PCE2, AU1300_PIN_PCE1, AU1300_PIN_PIOS16,
+	AU1300_PIN_PIOR, AU1300_PIN_PWE, AU1300_PIN_PWAIT,
+	AU1300_PIN_PREG, AU1300_PIN_POE, AU1300_PIN_PIOW,
+	/* camera interface H/V sync inputs: 71-72 */
+	AU1300_PIN_CIMLS, AU1300_PIN_CIMFS,
+	/* PSC2/3 clocks: 73-74 */
+	AU1300_PIN_PSC2CLK, AU1300_PIN_PSC3CLK,
+};
+
+/* GPIC (Au1300) pin management: arch/mips/alchemy/common/gpioint.c */
+extern void au1300_pinfunc_to_gpio(enum au1300_multifunc_pins gpio);
+extern void au1300_pinfunc_to_dev(enum au1300_multifunc_pins gpio);
+extern void au1300_set_irq_priority(unsigned int irq, int p);
+extern void au1300_set_dbdma_gpio(int dchan, unsigned int gpio);
+
+/* Au1300 allows to disconnect certain blocks from internal power supply */
+enum au1300_vss_block {
+	AU1300_VSS_MPE = 0,
+	AU1300_VSS_BSA,
+	AU1300_VSS_GPE,
+	AU1300_VSS_MGP,
+};
+
+extern void au1300_vss_block_control(int block, int enable);
+
+enum soc_au1000_ints {
+	AU1000_FIRST_INT	= AU1000_INTC0_INT_BASE,
+	AU1000_UART0_INT	= AU1000_FIRST_INT,
+	AU1000_UART1_INT,
+	AU1000_UART2_INT,
+	AU1000_UART3_INT,
+	AU1000_SSI0_INT,
+	AU1000_SSI1_INT,
+	AU1000_DMA_INT_BASE,
+
+	AU1000_TOY_INT		= AU1000_FIRST_INT + 14,
+	AU1000_TOY_MATCH0_INT,
+	AU1000_TOY_MATCH1_INT,
+	AU1000_TOY_MATCH2_INT,
+	AU1000_RTC_INT,
+	AU1000_RTC_MATCH0_INT,
+	AU1000_RTC_MATCH1_INT,
+	AU1000_RTC_MATCH2_INT,
+	AU1000_IRDA_TX_INT,
+	AU1000_IRDA_RX_INT,
+	AU1000_USB_DEV_REQ_INT,
+	AU1000_USB_DEV_SUS_INT,
+	AU1000_USB_HOST_INT,
+	AU1000_ACSYNC_INT,
+	AU1000_MAC0_DMA_INT,
+	AU1000_MAC1_DMA_INT,
+	AU1000_I2S_UO_INT,
+	AU1000_AC97C_INT,
+	AU1000_GPIO0_INT,
+	AU1000_GPIO1_INT,
+	AU1000_GPIO2_INT,
+	AU1000_GPIO3_INT,
+	AU1000_GPIO4_INT,
+	AU1000_GPIO5_INT,
+	AU1000_GPIO6_INT,
+	AU1000_GPIO7_INT,
+	AU1000_GPIO8_INT,
+	AU1000_GPIO9_INT,
+	AU1000_GPIO10_INT,
+	AU1000_GPIO11_INT,
+	AU1000_GPIO12_INT,
+	AU1000_GPIO13_INT,
+	AU1000_GPIO14_INT,
+	AU1000_GPIO15_INT,
+	AU1000_GPIO16_INT,
+	AU1000_GPIO17_INT,
+	AU1000_GPIO18_INT,
+	AU1000_GPIO19_INT,
+	AU1000_GPIO20_INT,
+	AU1000_GPIO21_INT,
+	AU1000_GPIO22_INT,
+	AU1000_GPIO23_INT,
+	AU1000_GPIO24_INT,
+	AU1000_GPIO25_INT,
+	AU1000_GPIO26_INT,
+	AU1000_GPIO27_INT,
+	AU1000_GPIO28_INT,
+	AU1000_GPIO29_INT,
+	AU1000_GPIO30_INT,
+	AU1000_GPIO31_INT,
+};
+
+enum soc_au1100_ints {
+	AU1100_FIRST_INT	= AU1000_INTC0_INT_BASE,
+	AU1100_UART0_INT	= AU1100_FIRST_INT,
+	AU1100_UART1_INT,
+	AU1100_SD_INT,
+	AU1100_UART3_INT,
+	AU1100_SSI0_INT,
+	AU1100_SSI1_INT,
+	AU1100_DMA_INT_BASE,
+
+	AU1100_TOY_INT		= AU1100_FIRST_INT + 14,
+	AU1100_TOY_MATCH0_INT,
+	AU1100_TOY_MATCH1_INT,
+	AU1100_TOY_MATCH2_INT,
+	AU1100_RTC_INT,
+	AU1100_RTC_MATCH0_INT,
+	AU1100_RTC_MATCH1_INT,
+	AU1100_RTC_MATCH2_INT,
+	AU1100_IRDA_TX_INT,
+	AU1100_IRDA_RX_INT,
+	AU1100_USB_DEV_REQ_INT,
+	AU1100_USB_DEV_SUS_INT,
+	AU1100_USB_HOST_INT,
+	AU1100_ACSYNC_INT,
+	AU1100_MAC0_DMA_INT,
+	AU1100_GPIO208_215_INT,
+	AU1100_LCD_INT,
+	AU1100_AC97C_INT,
+	AU1100_GPIO0_INT,
+	AU1100_GPIO1_INT,
+	AU1100_GPIO2_INT,
+	AU1100_GPIO3_INT,
+	AU1100_GPIO4_INT,
+	AU1100_GPIO5_INT,
+	AU1100_GPIO6_INT,
+	AU1100_GPIO7_INT,
+	AU1100_GPIO8_INT,
+	AU1100_GPIO9_INT,
+	AU1100_GPIO10_INT,
+	AU1100_GPIO11_INT,
+	AU1100_GPIO12_INT,
+	AU1100_GPIO13_INT,
+	AU1100_GPIO14_INT,
+	AU1100_GPIO15_INT,
+	AU1100_GPIO16_INT,
+	AU1100_GPIO17_INT,
+	AU1100_GPIO18_INT,
+	AU1100_GPIO19_INT,
+	AU1100_GPIO20_INT,
+	AU1100_GPIO21_INT,
+	AU1100_GPIO22_INT,
+	AU1100_GPIO23_INT,
+	AU1100_GPIO24_INT,
+	AU1100_GPIO25_INT,
+	AU1100_GPIO26_INT,
+	AU1100_GPIO27_INT,
+	AU1100_GPIO28_INT,
+	AU1100_GPIO29_INT,
+	AU1100_GPIO30_INT,
+	AU1100_GPIO31_INT,
+};
+
+enum soc_au1500_ints {
+	AU1500_FIRST_INT	= AU1000_INTC0_INT_BASE,
+	AU1500_UART0_INT	= AU1500_FIRST_INT,
+	AU1500_PCI_INTA,
+	AU1500_PCI_INTB,
+	AU1500_UART3_INT,
+	AU1500_PCI_INTC,
+	AU1500_PCI_INTD,
+	AU1500_DMA_INT_BASE,
+
+	AU1500_TOY_INT		= AU1500_FIRST_INT + 14,
+	AU1500_TOY_MATCH0_INT,
+	AU1500_TOY_MATCH1_INT,
+	AU1500_TOY_MATCH2_INT,
+	AU1500_RTC_INT,
+	AU1500_RTC_MATCH0_INT,
+	AU1500_RTC_MATCH1_INT,
+	AU1500_RTC_MATCH2_INT,
+	AU1500_PCI_ERR_INT,
+	AU1500_RESERVED_INT,
+	AU1500_USB_DEV_REQ_INT,
+	AU1500_USB_DEV_SUS_INT,
+	AU1500_USB_HOST_INT,
+	AU1500_ACSYNC_INT,
+	AU1500_MAC0_DMA_INT,
+	AU1500_MAC1_DMA_INT,
+	AU1500_AC97C_INT	= AU1500_FIRST_INT + 31,
+	AU1500_GPIO0_INT,
+	AU1500_GPIO1_INT,
+	AU1500_GPIO2_INT,
+	AU1500_GPIO3_INT,
+	AU1500_GPIO4_INT,
+	AU1500_GPIO5_INT,
+	AU1500_GPIO6_INT,
+	AU1500_GPIO7_INT,
+	AU1500_GPIO8_INT,
+	AU1500_GPIO9_INT,
+	AU1500_GPIO10_INT,
+	AU1500_GPIO11_INT,
+	AU1500_GPIO12_INT,
+	AU1500_GPIO13_INT,
+	AU1500_GPIO14_INT,
+	AU1500_GPIO15_INT,
+	AU1500_GPIO200_INT,
+	AU1500_GPIO201_INT,
+	AU1500_GPIO202_INT,
+	AU1500_GPIO203_INT,
+	AU1500_GPIO20_INT,
+	AU1500_GPIO204_INT,
+	AU1500_GPIO205_INT,
+	AU1500_GPIO23_INT,
+	AU1500_GPIO24_INT,
+	AU1500_GPIO25_INT,
+	AU1500_GPIO26_INT,
+	AU1500_GPIO27_INT,
+	AU1500_GPIO28_INT,
+	AU1500_GPIO206_INT,
+	AU1500_GPIO207_INT,
+	AU1500_GPIO208_215_INT,
+};
+
+enum soc_au1550_ints {
+	AU1550_FIRST_INT	= AU1000_INTC0_INT_BASE,
+	AU1550_UART0_INT	= AU1550_FIRST_INT,
+	AU1550_PCI_INTA,
+	AU1550_PCI_INTB,
+	AU1550_DDMA_INT,
+	AU1550_CRYPTO_INT,
+	AU1550_PCI_INTC,
+	AU1550_PCI_INTD,
+	AU1550_PCI_RST_INT,
+	AU1550_UART1_INT,
+	AU1550_UART3_INT,
+	AU1550_PSC0_INT,
+	AU1550_PSC1_INT,
+	AU1550_PSC2_INT,
+	AU1550_PSC3_INT,
+	AU1550_TOY_INT,
+	AU1550_TOY_MATCH0_INT,
+	AU1550_TOY_MATCH1_INT,
+	AU1550_TOY_MATCH2_INT,
+	AU1550_RTC_INT,
+	AU1550_RTC_MATCH0_INT,
+	AU1550_RTC_MATCH1_INT,
+	AU1550_RTC_MATCH2_INT,
+
+	AU1550_NAND_INT		= AU1550_FIRST_INT + 23,
+	AU1550_USB_DEV_REQ_INT,
+	AU1550_USB_DEV_SUS_INT,
+	AU1550_USB_HOST_INT,
+	AU1550_MAC0_DMA_INT,
+	AU1550_MAC1_DMA_INT,
+	AU1550_GPIO0_INT	= AU1550_FIRST_INT + 32,
+	AU1550_GPIO1_INT,
+	AU1550_GPIO2_INT,
+	AU1550_GPIO3_INT,
+	AU1550_GPIO4_INT,
+	AU1550_GPIO5_INT,
+	AU1550_GPIO6_INT,
+	AU1550_GPIO7_INT,
+	AU1550_GPIO8_INT,
+	AU1550_GPIO9_INT,
+	AU1550_GPIO10_INT,
+	AU1550_GPIO11_INT,
+	AU1550_GPIO12_INT,
+	AU1550_GPIO13_INT,
+	AU1550_GPIO14_INT,
+	AU1550_GPIO15_INT,
+	AU1550_GPIO200_INT,
+	AU1550_GPIO201_205_INT, /* Logical or of GPIO201:205 */
+	AU1550_GPIO16_INT,
+	AU1550_GPIO17_INT,
+	AU1550_GPIO20_INT,
+	AU1550_GPIO21_INT,
+	AU1550_GPIO22_INT,
+	AU1550_GPIO23_INT,
+	AU1550_GPIO24_INT,
+	AU1550_GPIO25_INT,
+	AU1550_GPIO26_INT,
+	AU1550_GPIO27_INT,
+	AU1550_GPIO28_INT,
+	AU1550_GPIO206_INT,
+	AU1550_GPIO207_INT,
+	AU1550_GPIO208_215_INT, /* Logical or of GPIO208:215 */
+};
+
+enum soc_au1200_ints {
+	AU1200_FIRST_INT	= AU1000_INTC0_INT_BASE,
+	AU1200_UART0_INT	= AU1200_FIRST_INT,
+	AU1200_SWT_INT,
+	AU1200_SD_INT,
+	AU1200_DDMA_INT,
+	AU1200_MAE_BE_INT,
+	AU1200_GPIO200_INT,
+	AU1200_GPIO201_INT,
+	AU1200_GPIO202_INT,
+	AU1200_UART1_INT,
+	AU1200_MAE_FE_INT,
+	AU1200_PSC0_INT,
+	AU1200_PSC1_INT,
+	AU1200_AES_INT,
+	AU1200_CAMERA_INT,
+	AU1200_TOY_INT,
+	AU1200_TOY_MATCH0_INT,
+	AU1200_TOY_MATCH1_INT,
+	AU1200_TOY_MATCH2_INT,
+	AU1200_RTC_INT,
+	AU1200_RTC_MATCH0_INT,
+	AU1200_RTC_MATCH1_INT,
+	AU1200_RTC_MATCH2_INT,
+	AU1200_GPIO203_INT,
+	AU1200_NAND_INT,
+	AU1200_GPIO204_INT,
+	AU1200_GPIO205_INT,
+	AU1200_GPIO206_INT,
+	AU1200_GPIO207_INT,
+	AU1200_GPIO208_215_INT, /* Logical OR of 208:215 */
+	AU1200_USB_INT,
+	AU1200_LCD_INT,
+	AU1200_MAE_BOTH_INT,
+	AU1200_GPIO0_INT,
+	AU1200_GPIO1_INT,
+	AU1200_GPIO2_INT,
+	AU1200_GPIO3_INT,
+	AU1200_GPIO4_INT,
+	AU1200_GPIO5_INT,
+	AU1200_GPIO6_INT,
+	AU1200_GPIO7_INT,
+	AU1200_GPIO8_INT,
+	AU1200_GPIO9_INT,
+	AU1200_GPIO10_INT,
+	AU1200_GPIO11_INT,
+	AU1200_GPIO12_INT,
+	AU1200_GPIO13_INT,
+	AU1200_GPIO14_INT,
+	AU1200_GPIO15_INT,
+	AU1200_GPIO16_INT,
+	AU1200_GPIO17_INT,
+	AU1200_GPIO18_INT,
+	AU1200_GPIO19_INT,
+	AU1200_GPIO20_INT,
+	AU1200_GPIO21_INT,
+	AU1200_GPIO22_INT,
+	AU1200_GPIO23_INT,
+	AU1200_GPIO24_INT,
+	AU1200_GPIO25_INT,
+	AU1200_GPIO26_INT,
+	AU1200_GPIO27_INT,
+	AU1200_GPIO28_INT,
+	AU1200_GPIO29_INT,
+	AU1200_GPIO30_INT,
+	AU1200_GPIO31_INT,
+};
+
+#endif /* !defined (_LANGUAGE_ASSEMBLY) */
+
+#endif
diff --git a/arch/mips/include/asm/mach-au1x00/au1000_dma.h b/arch/mips/include/asm/mach-au1x00/au1000_dma.h
new file mode 100644
index 000000000..0a0cd4270
--- /dev/null
+++ b/arch/mips/include/asm/mach-au1x00/au1000_dma.h
@@ -0,0 +1,453 @@
+/*
+ * BRIEF MODULE DESCRIPTION
+ *	Defines for using and allocating DMA channels on the Alchemy
+ *      Au1x00 MIPS processors.
+ *
+ * Copyright 2000, 2008 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc. <source@mvista.com>
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ */
+#ifndef __ASM_AU1000_DMA_H
+#define __ASM_AU1000_DMA_H
+
+#include <linux/io.h>		/* need byte IO */
+#include <linux/spinlock.h>	/* And spinlocks */
+#include <linux/delay.h>
+
+#define NUM_AU1000_DMA_CHANNELS 8
+
+/* DMA Channel Register Offsets */
+#define DMA_MODE_SET		0x00000000
+#define DMA_MODE_READ		DMA_MODE_SET
+#define DMA_MODE_CLEAR		0x00000004
+/* DMA Mode register bits follow */
+#define DMA_DAH_MASK		(0x0f << 20)
+#define DMA_DID_BIT		16
+#define DMA_DID_MASK		(0x0f << DMA_DID_BIT)
+#define DMA_DS			(1 << 15)
+#define DMA_BE			(1 << 13)
+#define DMA_DR			(1 << 12)
+#define DMA_TS8			(1 << 11)
+#define DMA_DW_BIT		9
+#define DMA_DW_MASK		(0x03 << DMA_DW_BIT)
+#define DMA_DW8			(0 << DMA_DW_BIT)
+#define DMA_DW16		(1 << DMA_DW_BIT)
+#define DMA_DW32		(2 << DMA_DW_BIT)
+#define DMA_NC			(1 << 8)
+#define DMA_IE			(1 << 7)
+#define DMA_HALT		(1 << 6)
+#define DMA_GO			(1 << 5)
+#define DMA_AB			(1 << 4)
+#define DMA_D1			(1 << 3)
+#define DMA_BE1			(1 << 2)
+#define DMA_D0			(1 << 1)
+#define DMA_BE0			(1 << 0)
+
+#define DMA_PERIPHERAL_ADDR	0x00000008
+#define DMA_BUFFER0_START	0x0000000C
+#define DMA_BUFFER1_START	0x00000014
+#define DMA_BUFFER0_COUNT	0x00000010
+#define DMA_BUFFER1_COUNT	0x00000018
+#define DMA_BAH_BIT	16
+#define DMA_BAH_MASK	(0x0f << DMA_BAH_BIT)
+#define DMA_COUNT_BIT	0
+#define DMA_COUNT_MASK	(0xffff << DMA_COUNT_BIT)
+
+/* DMA Device IDs follow */
+enum {
+	DMA_ID_UART0_TX = 0,
+	DMA_ID_UART0_RX,
+	DMA_ID_GP04,
+	DMA_ID_GP05,
+	DMA_ID_AC97C_TX,
+	DMA_ID_AC97C_RX,
+	DMA_ID_UART3_TX,
+	DMA_ID_UART3_RX,
+	DMA_ID_USBDEV_EP0_RX,
+	DMA_ID_USBDEV_EP0_TX,
+	DMA_ID_USBDEV_EP2_TX,
+	DMA_ID_USBDEV_EP3_TX,
+	DMA_ID_USBDEV_EP4_RX,
+	DMA_ID_USBDEV_EP5_RX,
+	DMA_ID_I2S_TX,
+	DMA_ID_I2S_RX,
+	DMA_NUM_DEV
+};
+
+/* DMA Device ID's for 2nd bank (AU1100) follow */
+enum {
+	DMA_ID_SD0_TX = 0,
+	DMA_ID_SD0_RX,
+	DMA_ID_SD1_TX,
+	DMA_ID_SD1_RX,
+	DMA_NUM_DEV_BANK2
+};
+
+struct dma_chan {
+	int dev_id;		/* this channel is allocated if >= 0, */
+				/* free otherwise */
+	void __iomem *io;
+	const char *dev_str;
+	int irq;
+	void *irq_dev;
+	unsigned int fifo_addr;
+	unsigned int mode;
+};
+
+/* These are in arch/mips/au1000/common/dma.c */
+extern struct dma_chan au1000_dma_table[];
+extern int request_au1000_dma(int dev_id,
+			      const char *dev_str,
+			      irq_handler_t irqhandler,
+			      unsigned long irqflags,
+			      void *irq_dev_id);
+extern void free_au1000_dma(unsigned int dmanr);
+extern int au1000_dma_read_proc(char *buf, char **start, off_t fpos,
+				int length, int *eof, void *data);
+extern void dump_au1000_dma_channel(unsigned int dmanr);
+extern spinlock_t au1000_dma_spin_lock;
+
+static inline struct dma_chan *get_dma_chan(unsigned int dmanr)
+{
+	if (dmanr >= NUM_AU1000_DMA_CHANNELS ||
+	    au1000_dma_table[dmanr].dev_id < 0)
+		return NULL;
+	return &au1000_dma_table[dmanr];
+}
+
+static inline unsigned long claim_dma_lock(void)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&au1000_dma_spin_lock, flags);
+	return flags;
+}
+
+static inline void release_dma_lock(unsigned long flags)
+{
+	spin_unlock_irqrestore(&au1000_dma_spin_lock, flags);
+}
+
+/*
+ * Set the DMA buffer enable bits in the mode register.
+ */
+static inline void enable_dma_buffer0(unsigned int dmanr)
+{
+	struct dma_chan *chan = get_dma_chan(dmanr);
+
+	if (!chan)
+		return;
+	__raw_writel(DMA_BE0, chan->io + DMA_MODE_SET);
+}
+
+static inline void enable_dma_buffer1(unsigned int dmanr)
+{
+	struct dma_chan *chan = get_dma_chan(dmanr);
+
+	if (!chan)
+		return;
+	__raw_writel(DMA_BE1, chan->io + DMA_MODE_SET);
+}
+static inline void enable_dma_buffers(unsigned int dmanr)
+{
+	struct dma_chan *chan = get_dma_chan(dmanr);
+
+	if (!chan)
+		return;
+	__raw_writel(DMA_BE0 | DMA_BE1, chan->io + DMA_MODE_SET);
+}
+
+static inline void start_dma(unsigned int dmanr)
+{
+	struct dma_chan *chan = get_dma_chan(dmanr);
+
+	if (!chan)
+		return;
+	__raw_writel(DMA_GO, chan->io + DMA_MODE_SET);
+}
+
+#define DMA_HALT_POLL 0x5000
+
+static inline void halt_dma(unsigned int dmanr)
+{
+	struct dma_chan *chan = get_dma_chan(dmanr);
+	int i;
+
+	if (!chan)
+		return;
+	__raw_writel(DMA_GO, chan->io + DMA_MODE_CLEAR);
+
+	/* Poll the halt bit */
+	for (i = 0; i < DMA_HALT_POLL; i++)
+		if (__raw_readl(chan->io + DMA_MODE_READ) & DMA_HALT)
+			break;
+	if (i == DMA_HALT_POLL)
+		printk(KERN_INFO "halt_dma: HALT poll expired!\n");
+}
+
+static inline void disable_dma(unsigned int dmanr)
+{
+	struct dma_chan *chan = get_dma_chan(dmanr);
+
+	if (!chan)
+		return;
+
+	halt_dma(dmanr);
+
+	/* Now we can disable the buffers */
+	__raw_writel(~DMA_GO, chan->io + DMA_MODE_CLEAR);
+}
+
+static inline int dma_halted(unsigned int dmanr)
+{
+	struct dma_chan *chan = get_dma_chan(dmanr);
+
+	if (!chan)
+		return 1;
+	return (__raw_readl(chan->io + DMA_MODE_READ) & DMA_HALT) ? 1 : 0;
+}
+
+/* Initialize a DMA channel. */
+static inline void init_dma(unsigned int dmanr)
+{
+	struct dma_chan *chan = get_dma_chan(dmanr);
+	u32 mode;
+
+	if (!chan)
+		return;
+
+	disable_dma(dmanr);
+
+	/* Set device FIFO address */
+	__raw_writel(CPHYSADDR(chan->fifo_addr), chan->io + DMA_PERIPHERAL_ADDR);
+
+	mode = chan->mode | (chan->dev_id << DMA_DID_BIT);
+	if (chan->irq)
+		mode |= DMA_IE;
+
+	__raw_writel(~mode, chan->io + DMA_MODE_CLEAR);
+	__raw_writel(mode,	 chan->io + DMA_MODE_SET);
+}
+
+/*
+ * Set mode for a specific DMA channel
+ */
+static inline void set_dma_mode(unsigned int dmanr, unsigned int mode)
+{
+	struct dma_chan *chan = get_dma_chan(dmanr);
+
+	if (!chan)
+		return;
+	/*
+	 * set_dma_mode is only allowed to change endianess, direction,
+	 * transfer size, device FIFO width, and coherency settings.
+	 * Make sure anything else is masked off.
+	 */
+	mode &= (DMA_BE | DMA_DR | DMA_TS8 | DMA_DW_MASK | DMA_NC);
+	chan->mode &= ~(DMA_BE | DMA_DR | DMA_TS8 | DMA_DW_MASK | DMA_NC);
+	chan->mode |= mode;
+}
+
+static inline unsigned int get_dma_mode(unsigned int dmanr)
+{
+	struct dma_chan *chan = get_dma_chan(dmanr);
+
+	if (!chan)
+		return 0;
+	return chan->mode;
+}
+
+static inline int get_dma_active_buffer(unsigned int dmanr)
+{
+	struct dma_chan *chan = get_dma_chan(dmanr);
+
+	if (!chan)
+		return -1;
+	return (__raw_readl(chan->io + DMA_MODE_READ) & DMA_AB) ? 1 : 0;
+}
+
+/*
+ * Set the device FIFO address for a specific DMA channel - only
+ * applicable to GPO4 and GPO5. All the other devices have fixed
+ * FIFO addresses.
+ */
+static inline void set_dma_fifo_addr(unsigned int dmanr, unsigned int a)
+{
+	struct dma_chan *chan = get_dma_chan(dmanr);
+
+	if (!chan)
+		return;
+
+	if (chan->mode & DMA_DS)	/* second bank of device IDs */
+		return;
+
+	if (chan->dev_id != DMA_ID_GP04 && chan->dev_id != DMA_ID_GP05)
+		return;
+
+	__raw_writel(CPHYSADDR(a), chan->io + DMA_PERIPHERAL_ADDR);
+}
+
+/*
+ * Clear the DMA buffer done bits in the mode register.
+ */
+static inline void clear_dma_done0(unsigned int dmanr)
+{
+	struct dma_chan *chan = get_dma_chan(dmanr);
+
+	if (!chan)
+		return;
+	__raw_writel(DMA_D0, chan->io + DMA_MODE_CLEAR);
+}
+
+static inline void clear_dma_done1(unsigned int dmanr)
+{
+	struct dma_chan *chan = get_dma_chan(dmanr);
+
+	if (!chan)
+		return;
+	__raw_writel(DMA_D1, chan->io + DMA_MODE_CLEAR);
+}
+
+/*
+ * This does nothing - not applicable to Au1000 DMA.
+ */
+static inline void set_dma_page(unsigned int dmanr, char pagenr)
+{
+}
+
+/*
+ * Set Buffer 0 transfer address for specific DMA channel.
+ */
+static inline void set_dma_addr0(unsigned int dmanr, unsigned int a)
+{
+	struct dma_chan *chan = get_dma_chan(dmanr);
+
+	if (!chan)
+		return;
+	__raw_writel(a, chan->io + DMA_BUFFER0_START);
+}
+
+/*
+ * Set Buffer 1 transfer address for specific DMA channel.
+ */
+static inline void set_dma_addr1(unsigned int dmanr, unsigned int a)
+{
+	struct dma_chan *chan = get_dma_chan(dmanr);
+
+	if (!chan)
+		return;
+	__raw_writel(a, chan->io + DMA_BUFFER1_START);
+}
+
+
+/*
+ * Set Buffer 0 transfer size (max 64k) for a specific DMA channel.
+ */
+static inline void set_dma_count0(unsigned int dmanr, unsigned int count)
+{
+	struct dma_chan *chan = get_dma_chan(dmanr);
+
+	if (!chan)
+		return;
+	count &= DMA_COUNT_MASK;
+	__raw_writel(count, chan->io + DMA_BUFFER0_COUNT);
+}
+
+/*
+ * Set Buffer 1 transfer size (max 64k) for a specific DMA channel.
+ */
+static inline void set_dma_count1(unsigned int dmanr, unsigned int count)
+{
+	struct dma_chan *chan = get_dma_chan(dmanr);
+
+	if (!chan)
+		return;
+	count &= DMA_COUNT_MASK;
+	__raw_writel(count, chan->io + DMA_BUFFER1_COUNT);
+}
+
+/*
+ * Set both buffer transfer sizes (max 64k) for a specific DMA channel.
+ */
+static inline void set_dma_count(unsigned int dmanr, unsigned int count)
+{
+	struct dma_chan *chan = get_dma_chan(dmanr);
+
+	if (!chan)
+		return;
+	count &= DMA_COUNT_MASK;
+	__raw_writel(count, chan->io + DMA_BUFFER0_COUNT);
+	__raw_writel(count, chan->io + DMA_BUFFER1_COUNT);
+}
+
+/*
+ * Returns which buffer has its done bit set in the mode register.
+ * Returns -1 if neither or both done bits set.
+ */
+static inline unsigned int get_dma_buffer_done(unsigned int dmanr)
+{
+	struct dma_chan *chan = get_dma_chan(dmanr);
+
+	if (!chan)
+		return 0;
+	return __raw_readl(chan->io + DMA_MODE_READ) & (DMA_D0 | DMA_D1);
+}
+
+
+/*
+ * Returns the DMA channel's Buffer Done IRQ number.
+ */
+static inline int get_dma_done_irq(unsigned int dmanr)
+{
+	struct dma_chan *chan = get_dma_chan(dmanr);
+
+	if (!chan)
+		return -1;
+	return chan->irq;
+}
+
+/*
+ * Get DMA residue count. Returns the number of _bytes_ left to transfer.
+ */
+static inline int get_dma_residue(unsigned int dmanr)
+{
+	int curBufCntReg, count;
+	struct dma_chan *chan = get_dma_chan(dmanr);
+
+	if (!chan)
+		return 0;
+
+	curBufCntReg = (__raw_readl(chan->io + DMA_MODE_READ) & DMA_AB) ?
+	    DMA_BUFFER1_COUNT : DMA_BUFFER0_COUNT;
+
+	count = __raw_readl(chan->io + curBufCntReg) & DMA_COUNT_MASK;
+
+	if ((chan->mode & DMA_DW_MASK) == DMA_DW16)
+		count <<= 1;
+	else if ((chan->mode & DMA_DW_MASK) == DMA_DW32)
+		count <<= 2;
+
+	return count;
+}
+
+#endif /* __ASM_AU1000_DMA_H */
diff --git a/arch/mips/include/asm/mach-au1x00/au1100_mmc.h b/arch/mips/include/asm/mach-au1x00/au1100_mmc.h
new file mode 100644
index 000000000..cadab91ce
--- /dev/null
+++ b/arch/mips/include/asm/mach-au1x00/au1100_mmc.h
@@ -0,0 +1,210 @@
+/*
+ * BRIEF MODULE DESCRIPTION
+ *	Defines for using the MMC/SD controllers on the
+ *      Alchemy Au1100 mips processor.
+ *
+ * Copyright (c) 2003 Embedded Edge, LLC.
+ * Author: Embedded Edge, LLC.
+ *         	dan@embeddededge.com or tim@embeddededge.com
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ */
+/*
+ * AU1100 MMC/SD definitions.
+ *
+ * From "AMD Alchemy Solutions Au1100 Processor Data Book - Preliminary"
+ *    June, 2003
+ */
+
+#ifndef __ASM_AU1100_MMC_H
+#define __ASM_AU1100_MMC_H
+
+#include <linux/leds.h>
+
+struct au1xmmc_platform_data {
+	int(*cd_setup)(void *mmc_host, int on);
+	int(*card_inserted)(void *mmc_host);
+	int(*card_readonly)(void *mmc_host);
+	void(*set_power)(void *mmc_host, int state);
+	struct led_classdev *led;
+	unsigned long mask_host_caps;
+};
+
+#define SD0_BASE	0xB0600000
+#define SD1_BASE	0xB0680000
+
+
+/*
+ *  Register offsets.
+ */
+#define SD_TXPORT	(0x0000)
+#define SD_RXPORT	(0x0004)
+#define SD_CONFIG	(0x0008)
+#define SD_ENABLE	(0x000C)
+#define SD_CONFIG2	(0x0010)
+#define SD_BLKSIZE	(0x0014)
+#define SD_STATUS	(0x0018)
+#define SD_DEBUG	(0x001C)
+#define SD_CMD		(0x0020)
+#define SD_CMDARG	(0x0024)
+#define SD_RESP3	(0x0028)
+#define SD_RESP2	(0x002C)
+#define SD_RESP1	(0x0030)
+#define SD_RESP0	(0x0034)
+#define SD_TIMEOUT	(0x0038)
+
+
+/*
+ *  SD_TXPORT bit definitions.
+ */
+#define SD_TXPORT_TXD	(0x000000ff)
+
+
+/*
+ *  SD_RXPORT bit definitions.
+ */
+#define SD_RXPORT_RXD	(0x000000ff)
+
+
+/*
+ *  SD_CONFIG bit definitions.
+ */
+#define SD_CONFIG_DIV	(0x000001ff)
+#define SD_CONFIG_DE	(0x00000200)
+#define SD_CONFIG_NE	(0x00000400)
+#define SD_CONFIG_TU	(0x00000800)
+#define SD_CONFIG_TO	(0x00001000)
+#define SD_CONFIG_RU	(0x00002000)
+#define SD_CONFIG_RO	(0x00004000)
+#define SD_CONFIG_I	(0x00008000)
+#define SD_CONFIG_CR	(0x00010000)
+#define SD_CONFIG_RAT	(0x00020000)
+#define SD_CONFIG_DD	(0x00040000)
+#define SD_CONFIG_DT	(0x00080000)
+#define SD_CONFIG_SC	(0x00100000)
+#define SD_CONFIG_RC	(0x00200000)
+#define SD_CONFIG_WC	(0x00400000)
+#define SD_CONFIG_xxx	(0x00800000)
+#define SD_CONFIG_TH	(0x01000000)
+#define SD_CONFIG_TE	(0x02000000)
+#define SD_CONFIG_TA	(0x04000000)
+#define SD_CONFIG_RH	(0x08000000)
+#define SD_CONFIG_RA	(0x10000000)
+#define SD_CONFIG_RF	(0x20000000)
+#define SD_CONFIG_CD	(0x40000000)
+#define SD_CONFIG_SI	(0x80000000)
+
+
+/*
+ *  SD_ENABLE bit definitions.
+ */
+#define SD_ENABLE_CE	(0x00000001)
+#define SD_ENABLE_R	(0x00000002)
+
+
+/*
+ *  SD_CONFIG2 bit definitions.
+ */
+#define SD_CONFIG2_EN	(0x00000001)
+#define SD_CONFIG2_FF	(0x00000002)
+#define SD_CONFIG2_xx1	(0x00000004)
+#define SD_CONFIG2_DF	(0x00000008)
+#define SD_CONFIG2_DC	(0x00000010)
+#define SD_CONFIG2_xx2	(0x000000e0)
+#define SD_CONFIG2_BB	(0x00000080)
+#define SD_CONFIG2_WB	(0x00000100)
+#define SD_CONFIG2_RW	(0x00000200)
+#define SD_CONFIG2_DP	(0x00000400)
+
+
+/*
+ *  SD_BLKSIZE bit definitions.
+ */
+#define SD_BLKSIZE_BS	(0x000007ff)
+#define SD_BLKSIZE_BS_SHIFT	 (0)
+#define SD_BLKSIZE_BC	(0x01ff0000)
+#define SD_BLKSIZE_BC_SHIFT	(16)
+
+
+/*
+ *  SD_STATUS bit definitions.
+ */
+#define SD_STATUS_DCRCW (0x00000007)
+#define SD_STATUS_xx1	(0x00000008)
+#define SD_STATUS_CB	(0x00000010)
+#define SD_STATUS_DB	(0x00000020)
+#define SD_STATUS_CF	(0x00000040)
+#define SD_STATUS_D3	(0x00000080)
+#define SD_STATUS_xx2	(0x00000300)
+#define SD_STATUS_NE	(0x00000400)
+#define SD_STATUS_TU	(0x00000800)
+#define SD_STATUS_TO	(0x00001000)
+#define SD_STATUS_RU	(0x00002000)
+#define SD_STATUS_RO	(0x00004000)
+#define SD_STATUS_I	(0x00008000)
+#define SD_STATUS_CR	(0x00010000)
+#define SD_STATUS_RAT	(0x00020000)
+#define SD_STATUS_DD	(0x00040000)
+#define SD_STATUS_DT	(0x00080000)
+#define SD_STATUS_SC	(0x00100000)
+#define SD_STATUS_RC	(0x00200000)
+#define SD_STATUS_WC	(0x00400000)
+#define SD_STATUS_xx3	(0x00800000)
+#define SD_STATUS_TH	(0x01000000)
+#define SD_STATUS_TE	(0x02000000)
+#define SD_STATUS_TA	(0x04000000)
+#define SD_STATUS_RH	(0x08000000)
+#define SD_STATUS_RA	(0x10000000)
+#define SD_STATUS_RF	(0x20000000)
+#define SD_STATUS_CD	(0x40000000)
+#define SD_STATUS_SI	(0x80000000)
+
+
+/*
+ *  SD_CMD bit definitions.
+ */
+#define SD_CMD_GO	(0x00000001)
+#define SD_CMD_RY	(0x00000002)
+#define SD_CMD_xx1	(0x0000000c)
+#define SD_CMD_CT_MASK	(0x000000f0)
+#define SD_CMD_CT_0	(0x00000000)
+#define SD_CMD_CT_1	(0x00000010)
+#define SD_CMD_CT_2	(0x00000020)
+#define SD_CMD_CT_3	(0x00000030)
+#define SD_CMD_CT_4	(0x00000040)
+#define SD_CMD_CT_5	(0x00000050)
+#define SD_CMD_CT_6	(0x00000060)
+#define SD_CMD_CT_7	(0x00000070)
+#define SD_CMD_CI	(0x0000ff00)
+#define SD_CMD_CI_SHIFT		(8)
+#define SD_CMD_RT_MASK	(0x00ff0000)
+#define SD_CMD_RT_0	(0x00000000)
+#define SD_CMD_RT_1	(0x00010000)
+#define SD_CMD_RT_2	(0x00020000)
+#define SD_CMD_RT_3	(0x00030000)
+#define SD_CMD_RT_4	(0x00040000)
+#define SD_CMD_RT_5	(0x00050000)
+#define SD_CMD_RT_6	(0x00060000)
+#define SD_CMD_RT_1B	(0x00810000)
+
+
+#endif /* __ASM_AU1100_MMC_H */
diff --git a/arch/mips/include/asm/mach-au1x00/au1200fb.h b/arch/mips/include/asm/mach-au1x00/au1200fb.h
new file mode 100644
index 000000000..e0e98f06c
--- /dev/null
+++ b/arch/mips/include/asm/mach-au1x00/au1200fb.h
@@ -0,0 +1,15 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * platform data for au1200fb driver.
+ */
+
+#ifndef _AU1200FB_PLAT_H_
+#define _AU1200FB_PLAT_H_
+
+struct au1200fb_platdata {
+	int (*panel_index)(void);
+	int (*panel_init)(void);
+	int (*panel_shutdown)(void);
+};
+
+#endif
diff --git a/arch/mips/include/asm/mach-au1x00/au1550_spi.h b/arch/mips/include/asm/mach-au1x00/au1550_spi.h
new file mode 100644
index 000000000..fe6ca4606
--- /dev/null
+++ b/arch/mips/include/asm/mach-au1x00/au1550_spi.h
@@ -0,0 +1,16 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * au1550_spi.h - Au1550 PSC SPI controller driver - platform data structure
+ */
+
+#ifndef _AU1550_SPI_H_
+#define _AU1550_SPI_H_
+
+struct au1550_spi_info {
+	u32 mainclk_hz;		/* main input clock frequency of PSC */
+	u16 num_chipselect;	/* number of chipselects supported */
+	void (*activate_cs)(struct au1550_spi_info *spi, int cs, int polarity);
+	void (*deactivate_cs)(struct au1550_spi_info *spi, int cs, int polarity);
+};
+
+#endif
diff --git a/arch/mips/include/asm/mach-au1x00/au1550nd.h b/arch/mips/include/asm/mach-au1x00/au1550nd.h
new file mode 100644
index 000000000..d26dc1dad
--- /dev/null
+++ b/arch/mips/include/asm/mach-au1x00/au1550nd.h
@@ -0,0 +1,17 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * platform data for the Au1550 NAND driver
+ */
+
+#ifndef _AU1550ND_H_
+#define _AU1550ND_H_
+
+#include <linux/mtd/partitions.h>
+
+struct au1550nd_platdata {
+	struct mtd_partition *parts;
+	int num_parts;
+	int devwidth;	/* 0 = 8bit device, 1 = 16bit device */
+};
+
+#endif
diff --git a/arch/mips/include/asm/mach-au1x00/au1xxx_dbdma.h b/arch/mips/include/asm/mach-au1x00/au1xxx_dbdma.h
new file mode 100644
index 000000000..456ddba15
--- /dev/null
+++ b/arch/mips/include/asm/mach-au1x00/au1xxx_dbdma.h
@@ -0,0 +1,388 @@
+/*
+ *
+ * BRIEF MODULE DESCRIPTION
+ *	Include file for Alchemy Semiconductor's Au1550 Descriptor
+ *	Based DMA Controller.
+ *
+ * Copyright 2004 Embedded Edge, LLC
+ *	dan@embeddededge.com
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+/*
+ * Specifics for the Au1xxx Descriptor-Based DMA Controller,
+ * first seen in the AU1550 part.
+ */
+#ifndef _AU1000_DBDMA_H_
+#define _AU1000_DBDMA_H_
+
+#ifndef _LANGUAGE_ASSEMBLY
+
+typedef volatile struct dbdma_global {
+	u32	ddma_config;
+	u32	ddma_intstat;
+	u32	ddma_throttle;
+	u32	ddma_inten;
+} dbdma_global_t;
+
+/* General Configuration. */
+#define DDMA_CONFIG_AF		(1 << 2)
+#define DDMA_CONFIG_AH		(1 << 1)
+#define DDMA_CONFIG_AL		(1 << 0)
+
+#define DDMA_THROTTLE_EN	(1 << 31)
+
+/* The structure of a DMA Channel. */
+typedef volatile struct au1xxx_dma_channel {
+	u32	ddma_cfg;	/* See below */
+	u32	ddma_desptr;	/* 32-byte aligned pointer to descriptor */
+	u32	ddma_statptr;	/* word aligned pointer to status word */
+	u32	ddma_dbell;	/* A write activates channel operation */
+	u32	ddma_irq;	/* If bit 0 set, interrupt pending */
+	u32	ddma_stat;	/* See below */
+	u32	ddma_bytecnt;	/* Byte count, valid only when chan idle */
+	/* Remainder, up to the 256 byte boundary, is reserved. */
+} au1x_dma_chan_t;
+
+#define DDMA_CFG_SED	(1 << 9)	/* source DMA level/edge detect */
+#define DDMA_CFG_SP	(1 << 8)	/* source DMA polarity */
+#define DDMA_CFG_DED	(1 << 7)	/* destination DMA level/edge detect */
+#define DDMA_CFG_DP	(1 << 6)	/* destination DMA polarity */
+#define DDMA_CFG_SYNC	(1 << 5)	/* Sync static bus controller */
+#define DDMA_CFG_PPR	(1 << 4)	/* PCI posted read/write control */
+#define DDMA_CFG_DFN	(1 << 3)	/* Descriptor fetch non-coherent */
+#define DDMA_CFG_SBE	(1 << 2)	/* Source big endian */
+#define DDMA_CFG_DBE	(1 << 1)	/* Destination big endian */
+#define DDMA_CFG_EN	(1 << 0)	/* Channel enable */
+
+/*
+ * Always set when descriptor processing done, regardless of
+ * interrupt enable state.  Reflected in global intstat, don't
+ * clear this until global intstat is read/used.
+ */
+#define DDMA_IRQ_IN	(1 << 0)
+
+#define DDMA_STAT_DB	(1 << 2)	/* Doorbell pushed */
+#define DDMA_STAT_V	(1 << 1)	/* Descriptor valid */
+#define DDMA_STAT_H	(1 << 0)	/* Channel Halted */
+
+/*
+ * "Standard" DDMA Descriptor.
+ * Must be 32-byte aligned.
+ */
+typedef volatile struct au1xxx_ddma_desc {
+	u32	dscr_cmd0;		/* See below */
+	u32	dscr_cmd1;		/* See below */
+	u32	dscr_source0;		/* source phys address */
+	u32	dscr_source1;		/* See below */
+	u32	dscr_dest0;		/* Destination address */
+	u32	dscr_dest1;		/* See below */
+	u32	dscr_stat;		/* completion status */
+	u32	dscr_nxtptr;		/* Next descriptor pointer (mostly) */
+	/*
+	 * First 32 bytes are HW specific!!!
+	 * Let's have some SW data following -- make sure it's 32 bytes.
+	 */
+	u32	sw_status;
+	u32	sw_context;
+	u32	sw_reserved[6];
+} au1x_ddma_desc_t;
+
+#define DSCR_CMD0_V		(1 << 31)	/* Descriptor valid */
+#define DSCR_CMD0_MEM		(1 << 30)	/* mem-mem transfer */
+#define DSCR_CMD0_SID_MASK	(0x1f << 25)	/* Source ID */
+#define DSCR_CMD0_DID_MASK	(0x1f << 20)	/* Destination ID */
+#define DSCR_CMD0_SW_MASK	(0x3 << 18)	/* Source Width */
+#define DSCR_CMD0_DW_MASK	(0x3 << 16)	/* Destination Width */
+#define DSCR_CMD0_ARB		(0x1 << 15)	/* Set for Hi Pri */
+#define DSCR_CMD0_DT_MASK	(0x3 << 13)	/* Descriptor Type */
+#define DSCR_CMD0_SN		(0x1 << 12)	/* Source non-coherent */
+#define DSCR_CMD0_DN		(0x1 << 11)	/* Destination non-coherent */
+#define DSCR_CMD0_SM		(0x1 << 10)	/* Stride mode */
+#define DSCR_CMD0_IE		(0x1 << 8)	/* Interrupt Enable */
+#define DSCR_CMD0_SP		(0x1 << 4)	/* Status pointer select */
+#define DSCR_CMD0_CV		(0x1 << 2)	/* Clear Valid when done */
+#define DSCR_CMD0_ST_MASK	(0x3 << 0)	/* Status instruction */
+
+#define SW_STATUS_INUSE		(1 << 0)
+
+/* Command 0 device IDs. */
+#define AU1550_DSCR_CMD0_UART0_TX	0
+#define AU1550_DSCR_CMD0_UART0_RX	1
+#define AU1550_DSCR_CMD0_UART3_TX	2
+#define AU1550_DSCR_CMD0_UART3_RX	3
+#define AU1550_DSCR_CMD0_DMA_REQ0	4
+#define AU1550_DSCR_CMD0_DMA_REQ1	5
+#define AU1550_DSCR_CMD0_DMA_REQ2	6
+#define AU1550_DSCR_CMD0_DMA_REQ3	7
+#define AU1550_DSCR_CMD0_USBDEV_RX0	8
+#define AU1550_DSCR_CMD0_USBDEV_TX0	9
+#define AU1550_DSCR_CMD0_USBDEV_TX1	10
+#define AU1550_DSCR_CMD0_USBDEV_TX2	11
+#define AU1550_DSCR_CMD0_USBDEV_RX3	12
+#define AU1550_DSCR_CMD0_USBDEV_RX4	13
+#define AU1550_DSCR_CMD0_PSC0_TX	14
+#define AU1550_DSCR_CMD0_PSC0_RX	15
+#define AU1550_DSCR_CMD0_PSC1_TX	16
+#define AU1550_DSCR_CMD0_PSC1_RX	17
+#define AU1550_DSCR_CMD0_PSC2_TX	18
+#define AU1550_DSCR_CMD0_PSC2_RX	19
+#define AU1550_DSCR_CMD0_PSC3_TX	20
+#define AU1550_DSCR_CMD0_PSC3_RX	21
+#define AU1550_DSCR_CMD0_PCI_WRITE	22
+#define AU1550_DSCR_CMD0_NAND_FLASH	23
+#define AU1550_DSCR_CMD0_MAC0_RX	24
+#define AU1550_DSCR_CMD0_MAC0_TX	25
+#define AU1550_DSCR_CMD0_MAC1_RX	26
+#define AU1550_DSCR_CMD0_MAC1_TX	27
+
+#define AU1200_DSCR_CMD0_UART0_TX	0
+#define AU1200_DSCR_CMD0_UART0_RX	1
+#define AU1200_DSCR_CMD0_UART1_TX	2
+#define AU1200_DSCR_CMD0_UART1_RX	3
+#define AU1200_DSCR_CMD0_DMA_REQ0	4
+#define AU1200_DSCR_CMD0_DMA_REQ1	5
+#define AU1200_DSCR_CMD0_MAE_BE		6
+#define AU1200_DSCR_CMD0_MAE_FE		7
+#define AU1200_DSCR_CMD0_SDMS_TX0	8
+#define AU1200_DSCR_CMD0_SDMS_RX0	9
+#define AU1200_DSCR_CMD0_SDMS_TX1	10
+#define AU1200_DSCR_CMD0_SDMS_RX1	11
+#define AU1200_DSCR_CMD0_AES_TX		13
+#define AU1200_DSCR_CMD0_AES_RX		12
+#define AU1200_DSCR_CMD0_PSC0_TX	14
+#define AU1200_DSCR_CMD0_PSC0_RX	15
+#define AU1200_DSCR_CMD0_PSC1_TX	16
+#define AU1200_DSCR_CMD0_PSC1_RX	17
+#define AU1200_DSCR_CMD0_CIM_RXA	18
+#define AU1200_DSCR_CMD0_CIM_RXB	19
+#define AU1200_DSCR_CMD0_CIM_RXC	20
+#define AU1200_DSCR_CMD0_MAE_BOTH	21
+#define AU1200_DSCR_CMD0_LCD		22
+#define AU1200_DSCR_CMD0_NAND_FLASH	23
+#define AU1200_DSCR_CMD0_PSC0_SYNC	24
+#define AU1200_DSCR_CMD0_PSC1_SYNC	25
+#define AU1200_DSCR_CMD0_CIM_SYNC	26
+
+#define AU1300_DSCR_CMD0_UART0_TX      0
+#define AU1300_DSCR_CMD0_UART0_RX      1
+#define AU1300_DSCR_CMD0_UART1_TX      2
+#define AU1300_DSCR_CMD0_UART1_RX      3
+#define AU1300_DSCR_CMD0_UART2_TX      4
+#define AU1300_DSCR_CMD0_UART2_RX      5
+#define AU1300_DSCR_CMD0_UART3_TX      6
+#define AU1300_DSCR_CMD0_UART3_RX      7
+#define AU1300_DSCR_CMD0_SDMS_TX0      8
+#define AU1300_DSCR_CMD0_SDMS_RX0      9
+#define AU1300_DSCR_CMD0_SDMS_TX1      10
+#define AU1300_DSCR_CMD0_SDMS_RX1      11
+#define AU1300_DSCR_CMD0_AES_TX	       12
+#define AU1300_DSCR_CMD0_AES_RX	       13
+#define AU1300_DSCR_CMD0_PSC0_TX       14
+#define AU1300_DSCR_CMD0_PSC0_RX       15
+#define AU1300_DSCR_CMD0_PSC1_TX       16
+#define AU1300_DSCR_CMD0_PSC1_RX       17
+#define AU1300_DSCR_CMD0_PSC2_TX       18
+#define AU1300_DSCR_CMD0_PSC2_RX       19
+#define AU1300_DSCR_CMD0_PSC3_TX       20
+#define AU1300_DSCR_CMD0_PSC3_RX       21
+#define AU1300_DSCR_CMD0_LCD	       22
+#define AU1300_DSCR_CMD0_NAND_FLASH    23
+#define AU1300_DSCR_CMD0_SDMS_TX2      24
+#define AU1300_DSCR_CMD0_SDMS_RX2      25
+#define AU1300_DSCR_CMD0_CIM_SYNC      26
+#define AU1300_DSCR_CMD0_UDMA	       27
+#define AU1300_DSCR_CMD0_DMA_REQ0      28
+#define AU1300_DSCR_CMD0_DMA_REQ1      29
+
+#define DSCR_CMD0_THROTTLE	30
+#define DSCR_CMD0_ALWAYS	31
+#define DSCR_NDEV_IDS		32
+/* This macro is used to find/create custom device types */
+#define DSCR_DEV2CUSTOM_ID(x, d) (((((x) & 0xFFFF) << 8) | 0x32000000) | \
+				  ((d) & 0xFF))
+#define DSCR_CUSTOM2DEV_ID(x)	((x) & 0xFF)
+
+#define DSCR_CMD0_SID(x)	(((x) & 0x1f) << 25)
+#define DSCR_CMD0_DID(x)	(((x) & 0x1f) << 20)
+
+/* Source/Destination transfer width. */
+#define DSCR_CMD0_BYTE		0
+#define DSCR_CMD0_HALFWORD	1
+#define DSCR_CMD0_WORD		2
+
+#define DSCR_CMD0_SW(x)		(((x) & 0x3) << 18)
+#define DSCR_CMD0_DW(x)		(((x) & 0x3) << 16)
+
+/* DDMA Descriptor Type. */
+#define DSCR_CMD0_STANDARD	0
+#define DSCR_CMD0_LITERAL	1
+#define DSCR_CMD0_CMP_BRANCH	2
+
+#define DSCR_CMD0_DT(x)		(((x) & 0x3) << 13)
+
+/* Status Instruction. */
+#define DSCR_CMD0_ST_NOCHANGE	0	/* Don't change */
+#define DSCR_CMD0_ST_CURRENT	1	/* Write current status */
+#define DSCR_CMD0_ST_CMD0	2	/* Write cmd0 with V cleared */
+#define DSCR_CMD0_ST_BYTECNT	3	/* Write remaining byte count */
+
+#define DSCR_CMD0_ST(x)		(((x) & 0x3) << 0)
+
+/* Descriptor Command 1. */
+#define DSCR_CMD1_SUPTR_MASK	(0xf << 28)	/* upper 4 bits of src addr */
+#define DSCR_CMD1_DUPTR_MASK	(0xf << 24)	/* upper 4 bits of dest addr */
+#define DSCR_CMD1_FL_MASK	(0x3 << 22)	/* Flag bits */
+#define DSCR_CMD1_BC_MASK	(0x3fffff)	/* Byte count */
+
+/* Flag description. */
+#define DSCR_CMD1_FL_MEM_STRIDE0	0
+#define DSCR_CMD1_FL_MEM_STRIDE1	1
+#define DSCR_CMD1_FL_MEM_STRIDE2	2
+
+#define DSCR_CMD1_FL(x)		(((x) & 0x3) << 22)
+
+/* Source1, 1-dimensional stride. */
+#define DSCR_SRC1_STS_MASK	(3 << 30)	/* Src xfer size */
+#define DSCR_SRC1_SAM_MASK	(3 << 28)	/* Src xfer movement */
+#define DSCR_SRC1_SB_MASK	(0x3fff << 14)	/* Block size */
+#define DSCR_SRC1_SB(x)		(((x) & 0x3fff) << 14)
+#define DSCR_SRC1_SS_MASK	(0x3fff << 0)	/* Stride */
+#define DSCR_SRC1_SS(x)		(((x) & 0x3fff) << 0)
+
+/* Dest1, 1-dimensional stride. */
+#define DSCR_DEST1_DTS_MASK	(3 << 30)	/* Dest xfer size */
+#define DSCR_DEST1_DAM_MASK	(3 << 28)	/* Dest xfer movement */
+#define DSCR_DEST1_DB_MASK	(0x3fff << 14)	/* Block size */
+#define DSCR_DEST1_DB(x)	(((x) & 0x3fff) << 14)
+#define DSCR_DEST1_DS_MASK	(0x3fff << 0)	/* Stride */
+#define DSCR_DEST1_DS(x)	(((x) & 0x3fff) << 0)
+
+#define DSCR_xTS_SIZE1		0
+#define DSCR_xTS_SIZE2		1
+#define DSCR_xTS_SIZE4		2
+#define DSCR_xTS_SIZE8		3
+#define DSCR_SRC1_STS(x)	(((x) & 3) << 30)
+#define DSCR_DEST1_DTS(x)	(((x) & 3) << 30)
+
+#define DSCR_xAM_INCREMENT	0
+#define DSCR_xAM_DECREMENT	1
+#define DSCR_xAM_STATIC		2
+#define DSCR_xAM_BURST		3
+#define DSCR_SRC1_SAM(x)	(((x) & 3) << 28)
+#define DSCR_DEST1_DAM(x)	(((x) & 3) << 28)
+
+/* The next descriptor pointer. */
+#define DSCR_NXTPTR_MASK	(0x07ffffff)
+#define DSCR_NXTPTR(x)		((x) >> 5)
+#define DSCR_GET_NXTPTR(x)	((x) << 5)
+#define DSCR_NXTPTR_MS		(1 << 27)
+
+/* The number of DBDMA channels. */
+#define NUM_DBDMA_CHANS 16
+
+/*
+ * DDMA API definitions
+ * FIXME: may not fit to this header file
+ */
+typedef struct dbdma_device_table {
+	u32	dev_id;
+	u32	dev_flags;
+	u32	dev_tsize;
+	u32	dev_devwidth;
+	u32	dev_physaddr;		/* If FIFO */
+	u32	dev_intlevel;
+	u32	dev_intpolarity;
+} dbdev_tab_t;
+
+
+typedef struct dbdma_chan_config {
+	spinlock_t	lock;
+
+	u32			chan_flags;
+	u32			chan_index;
+	dbdev_tab_t		*chan_src;
+	dbdev_tab_t		*chan_dest;
+	au1x_dma_chan_t		*chan_ptr;
+	au1x_ddma_desc_t	*chan_desc_base;
+	u32			cdb_membase; /* kmalloc base of above */
+	au1x_ddma_desc_t	*get_ptr, *put_ptr, *cur_ptr;
+	void			*chan_callparam;
+	void			(*chan_callback)(int, void *);
+} chan_tab_t;
+
+#define DEV_FLAGS_INUSE		(1 << 0)
+#define DEV_FLAGS_ANYUSE	(1 << 1)
+#define DEV_FLAGS_OUT		(1 << 2)
+#define DEV_FLAGS_IN		(1 << 3)
+#define DEV_FLAGS_BURSTABLE	(1 << 4)
+#define DEV_FLAGS_SYNC		(1 << 5)
+/* end DDMA API definitions */
+
+/*
+ * External functions for drivers to use.
+ * Use this to allocate a DBDMA channel.  The device IDs are one of
+ * the DSCR_CMD0 devices IDs, which is usually redefined to a more
+ * meaningful name.  The 'callback' is called during DMA completion
+ * interrupt.
+ */
+extern u32 au1xxx_dbdma_chan_alloc(u32 srcid, u32 destid,
+				   void (*callback)(int, void *),
+				   void *callparam);
+
+#define DBDMA_MEM_CHAN	DSCR_CMD0_ALWAYS
+
+/* Set the device width of an in/out FIFO. */
+u32 au1xxx_dbdma_set_devwidth(u32 chanid, int bits);
+
+/* Allocate a ring of descriptors for DBDMA. */
+u32 au1xxx_dbdma_ring_alloc(u32 chanid, int entries);
+
+/* Put buffers on source/destination descriptors. */
+u32 au1xxx_dbdma_put_source(u32 chanid, dma_addr_t buf, int nbytes, u32 flags);
+u32 au1xxx_dbdma_put_dest(u32 chanid, dma_addr_t buf, int nbytes, u32 flags);
+
+/* Get a buffer from the destination descriptor. */
+u32 au1xxx_dbdma_get_dest(u32 chanid, void **buf, int *nbytes);
+
+void au1xxx_dbdma_stop(u32 chanid);
+void au1xxx_dbdma_start(u32 chanid);
+void au1xxx_dbdma_reset(u32 chanid);
+u32 au1xxx_get_dma_residue(u32 chanid);
+
+void au1xxx_dbdma_chan_free(u32 chanid);
+void au1xxx_dbdma_dump(u32 chanid);
+
+u32 au1xxx_dbdma_put_dscr(u32 chanid, au1x_ddma_desc_t *dscr);
+
+u32 au1xxx_ddma_add_device(dbdev_tab_t *dev);
+extern void au1xxx_ddma_del_device(u32 devid);
+void *au1xxx_ddma_get_nextptr_virt(au1x_ddma_desc_t *dp);
+
+/*
+ *	Flags for the put_source/put_dest functions.
+ */
+#define DDMA_FLAGS_IE	(1 << 0)
+#define DDMA_FLAGS_NOIE (1 << 1)
+
+#endif /* _LANGUAGE_ASSEMBLY */
+#endif /* _AU1000_DBDMA_H_ */
diff --git a/arch/mips/include/asm/mach-au1x00/au1xxx_eth.h b/arch/mips/include/asm/mach-au1x00/au1xxx_eth.h
new file mode 100644
index 000000000..9d1c8d5ed
--- /dev/null
+++ b/arch/mips/include/asm/mach-au1x00/au1xxx_eth.h
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __AU1X00_ETH_DATA_H
+#define __AU1X00_ETH_DATA_H
+
+/* Platform specific PHY configuration passed to the MAC driver */
+struct au1000_eth_platform_data {
+	int phy_static_config;
+	int phy_search_highest_addr;
+	int phy1_search_mac0;
+	int phy_addr;
+	int phy_busid;
+	int phy_irq;
+	char mac[6];
+};
+
+void __init au1xxx_override_eth_cfg(unsigned port,
+			struct au1000_eth_platform_data *eth_data);
+
+#endif /* __AU1X00_ETH_DATA_H */
diff --git a/arch/mips/include/asm/mach-au1x00/au1xxx_psc.h b/arch/mips/include/asm/mach-au1x00/au1xxx_psc.h
new file mode 100644
index 000000000..8a9cd754b
--- /dev/null
+++ b/arch/mips/include/asm/mach-au1x00/au1xxx_psc.h
@@ -0,0 +1,466 @@
+/*
+ *
+ * BRIEF MODULE DESCRIPTION
+ *	Include file for Alchemy Semiconductor's Au1k CPU.
+ *
+ * Copyright 2004 Embedded Edge, LLC
+ *	dan@embeddededge.com
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+/* Specifics for the Au1xxx Programmable Serial Controllers, first
+ * seen in the AU1550 part.
+ */
+#ifndef _AU1000_PSC_H_
+#define _AU1000_PSC_H_
+
+/*
+ * The PSC select and control registers are common to all protocols.
+ */
+#define PSC_SEL_OFFSET		0x00000000
+#define PSC_CTRL_OFFSET		0x00000004
+
+#define PSC_SEL_CLK_MASK	(3 << 4)
+#define PSC_SEL_CLK_INTCLK	(0 << 4)
+#define PSC_SEL_CLK_EXTCLK	(1 << 4)
+#define PSC_SEL_CLK_SERCLK	(2 << 4)
+
+#define PSC_SEL_PS_MASK		0x00000007
+#define PSC_SEL_PS_DISABLED	0
+#define PSC_SEL_PS_SPIMODE	2
+#define PSC_SEL_PS_I2SMODE	3
+#define PSC_SEL_PS_AC97MODE	4
+#define PSC_SEL_PS_SMBUSMODE	5
+
+#define PSC_CTRL_DISABLE	0
+#define PSC_CTRL_SUSPEND	2
+#define PSC_CTRL_ENABLE		3
+
+/* AC97 Registers. */
+#define PSC_AC97CFG_OFFSET	0x00000008
+#define PSC_AC97MSK_OFFSET	0x0000000c
+#define PSC_AC97PCR_OFFSET	0x00000010
+#define PSC_AC97STAT_OFFSET	0x00000014
+#define PSC_AC97EVNT_OFFSET	0x00000018
+#define PSC_AC97TXRX_OFFSET	0x0000001c
+#define PSC_AC97CDC_OFFSET	0x00000020
+#define PSC_AC97RST_OFFSET	0x00000024
+#define PSC_AC97GPO_OFFSET	0x00000028
+#define PSC_AC97GPI_OFFSET	0x0000002c
+
+/* AC97 Config Register. */
+#define PSC_AC97CFG_RT_MASK	(3 << 30)
+#define PSC_AC97CFG_RT_FIFO1	(0 << 30)
+#define PSC_AC97CFG_RT_FIFO2	(1 << 30)
+#define PSC_AC97CFG_RT_FIFO4	(2 << 30)
+#define PSC_AC97CFG_RT_FIFO8	(3 << 30)
+
+#define PSC_AC97CFG_TT_MASK	(3 << 28)
+#define PSC_AC97CFG_TT_FIFO1	(0 << 28)
+#define PSC_AC97CFG_TT_FIFO2	(1 << 28)
+#define PSC_AC97CFG_TT_FIFO4	(2 << 28)
+#define PSC_AC97CFG_TT_FIFO8	(3 << 28)
+
+#define PSC_AC97CFG_DD_DISABLE	(1 << 27)
+#define PSC_AC97CFG_DE_ENABLE	(1 << 26)
+#define PSC_AC97CFG_SE_ENABLE	(1 << 25)
+
+#define PSC_AC97CFG_LEN_MASK	(0xf << 21)
+#define PSC_AC97CFG_TXSLOT_MASK (0x3ff << 11)
+#define PSC_AC97CFG_RXSLOT_MASK (0x3ff << 1)
+#define PSC_AC97CFG_GE_ENABLE	(1)
+
+/* Enable slots 3-12. */
+#define PSC_AC97CFG_TXSLOT_ENA(x)	(1 << (((x) - 3) + 11))
+#define PSC_AC97CFG_RXSLOT_ENA(x)	(1 << (((x) - 3) + 1))
+
+/*
+ * The word length equation is ((x) * 2) + 2, so choose 'x' appropriately.
+ * The only sensible numbers are 7, 9, or possibly 11.	Nah, just do the
+ * arithmetic in the macro.
+ */
+#define PSC_AC97CFG_SET_LEN(x)	(((((x) - 2) / 2) & 0xf) << 21)
+#define PSC_AC97CFG_GET_LEN(x)	(((((x) >> 21) & 0xf) * 2) + 2)
+
+/* AC97 Mask Register. */
+#define PSC_AC97MSK_GR		(1 << 25)
+#define PSC_AC97MSK_CD		(1 << 24)
+#define PSC_AC97MSK_RR		(1 << 13)
+#define PSC_AC97MSK_RO		(1 << 12)
+#define PSC_AC97MSK_RU		(1 << 11)
+#define PSC_AC97MSK_TR		(1 << 10)
+#define PSC_AC97MSK_TO		(1 << 9)
+#define PSC_AC97MSK_TU		(1 << 8)
+#define PSC_AC97MSK_RD		(1 << 5)
+#define PSC_AC97MSK_TD		(1 << 4)
+#define PSC_AC97MSK_ALLMASK	(PSC_AC97MSK_GR | PSC_AC97MSK_CD | \
+				 PSC_AC97MSK_RR | PSC_AC97MSK_RO | \
+				 PSC_AC97MSK_RU | PSC_AC97MSK_TR | \
+				 PSC_AC97MSK_TO | PSC_AC97MSK_TU | \
+				 PSC_AC97MSK_RD | PSC_AC97MSK_TD)
+
+/* AC97 Protocol Control Register. */
+#define PSC_AC97PCR_RC		(1 << 6)
+#define PSC_AC97PCR_RP		(1 << 5)
+#define PSC_AC97PCR_RS		(1 << 4)
+#define PSC_AC97PCR_TC		(1 << 2)
+#define PSC_AC97PCR_TP		(1 << 1)
+#define PSC_AC97PCR_TS		(1 << 0)
+
+/* AC97 Status register (read only). */
+#define PSC_AC97STAT_CB		(1 << 26)
+#define PSC_AC97STAT_CP		(1 << 25)
+#define PSC_AC97STAT_CR		(1 << 24)
+#define PSC_AC97STAT_RF		(1 << 13)
+#define PSC_AC97STAT_RE		(1 << 12)
+#define PSC_AC97STAT_RR		(1 << 11)
+#define PSC_AC97STAT_TF		(1 << 10)
+#define PSC_AC97STAT_TE		(1 << 9)
+#define PSC_AC97STAT_TR		(1 << 8)
+#define PSC_AC97STAT_RB		(1 << 5)
+#define PSC_AC97STAT_TB		(1 << 4)
+#define PSC_AC97STAT_DI		(1 << 2)
+#define PSC_AC97STAT_DR		(1 << 1)
+#define PSC_AC97STAT_SR		(1 << 0)
+
+/* AC97 Event Register. */
+#define PSC_AC97EVNT_GR		(1 << 25)
+#define PSC_AC97EVNT_CD		(1 << 24)
+#define PSC_AC97EVNT_RR		(1 << 13)
+#define PSC_AC97EVNT_RO		(1 << 12)
+#define PSC_AC97EVNT_RU		(1 << 11)
+#define PSC_AC97EVNT_TR		(1 << 10)
+#define PSC_AC97EVNT_TO		(1 << 9)
+#define PSC_AC97EVNT_TU		(1 << 8)
+#define PSC_AC97EVNT_RD		(1 << 5)
+#define PSC_AC97EVNT_TD		(1 << 4)
+
+/* CODEC Command Register. */
+#define PSC_AC97CDC_RD		(1 << 25)
+#define PSC_AC97CDC_ID_MASK	(3 << 23)
+#define PSC_AC97CDC_INDX_MASK	(0x7f << 16)
+#define PSC_AC97CDC_ID(x)	(((x) & 0x03) << 23)
+#define PSC_AC97CDC_INDX(x)	(((x) & 0x7f) << 16)
+
+/* AC97 Reset Control Register. */
+#define PSC_AC97RST_RST		(1 << 1)
+#define PSC_AC97RST_SNC		(1 << 0)
+
+/* PSC in I2S Mode. */
+typedef struct	psc_i2s {
+	u32	psc_sel;
+	u32	psc_ctrl;
+	u32	psc_i2scfg;
+	u32	psc_i2smsk;
+	u32	psc_i2spcr;
+	u32	psc_i2sstat;
+	u32	psc_i2sevent;
+	u32	psc_i2stxrx;
+	u32	psc_i2sudf;
+} psc_i2s_t;
+
+#define PSC_I2SCFG_OFFSET	0x08
+#define PSC_I2SMASK_OFFSET	0x0C
+#define PSC_I2SPCR_OFFSET	0x10
+#define PSC_I2SSTAT_OFFSET	0x14
+#define PSC_I2SEVENT_OFFSET	0x18
+#define PSC_I2SRXTX_OFFSET	0x1C
+#define PSC_I2SUDF_OFFSET	0x20
+
+/* I2S Config Register. */
+#define PSC_I2SCFG_RT_MASK	(3 << 30)
+#define PSC_I2SCFG_RT_FIFO1	(0 << 30)
+#define PSC_I2SCFG_RT_FIFO2	(1 << 30)
+#define PSC_I2SCFG_RT_FIFO4	(2 << 30)
+#define PSC_I2SCFG_RT_FIFO8	(3 << 30)
+
+#define PSC_I2SCFG_TT_MASK	(3 << 28)
+#define PSC_I2SCFG_TT_FIFO1	(0 << 28)
+#define PSC_I2SCFG_TT_FIFO2	(1 << 28)
+#define PSC_I2SCFG_TT_FIFO4	(2 << 28)
+#define PSC_I2SCFG_TT_FIFO8	(3 << 28)
+
+#define PSC_I2SCFG_DD_DISABLE	(1 << 27)
+#define PSC_I2SCFG_DE_ENABLE	(1 << 26)
+#define PSC_I2SCFG_SET_WS(x)	(((((x) / 2) - 1) & 0x7f) << 16)
+#define PSC_I2SCFG_WS(n)	((n & 0xFF) << 16)
+#define PSC_I2SCFG_WS_MASK	(PSC_I2SCFG_WS(0x3F))
+#define PSC_I2SCFG_WI		(1 << 15)
+
+#define PSC_I2SCFG_DIV_MASK	(3 << 13)
+#define PSC_I2SCFG_DIV2		(0 << 13)
+#define PSC_I2SCFG_DIV4		(1 << 13)
+#define PSC_I2SCFG_DIV8		(2 << 13)
+#define PSC_I2SCFG_DIV16	(3 << 13)
+
+#define PSC_I2SCFG_BI		(1 << 12)
+#define PSC_I2SCFG_BUF		(1 << 11)
+#define PSC_I2SCFG_MLJ		(1 << 10)
+#define PSC_I2SCFG_XM		(1 << 9)
+
+/* The word length equation is simply LEN+1. */
+#define PSC_I2SCFG_SET_LEN(x)	((((x) - 1) & 0x1f) << 4)
+#define PSC_I2SCFG_GET_LEN(x)	((((x) >> 4) & 0x1f) + 1)
+
+#define PSC_I2SCFG_LB		(1 << 2)
+#define PSC_I2SCFG_MLF		(1 << 1)
+#define PSC_I2SCFG_MS		(1 << 0)
+
+/* I2S Mask Register. */
+#define PSC_I2SMSK_RR		(1 << 13)
+#define PSC_I2SMSK_RO		(1 << 12)
+#define PSC_I2SMSK_RU		(1 << 11)
+#define PSC_I2SMSK_TR		(1 << 10)
+#define PSC_I2SMSK_TO		(1 << 9)
+#define PSC_I2SMSK_TU		(1 << 8)
+#define PSC_I2SMSK_RD		(1 << 5)
+#define PSC_I2SMSK_TD		(1 << 4)
+#define PSC_I2SMSK_ALLMASK	(PSC_I2SMSK_RR | PSC_I2SMSK_RO | \
+				 PSC_I2SMSK_RU | PSC_I2SMSK_TR | \
+				 PSC_I2SMSK_TO | PSC_I2SMSK_TU | \
+				 PSC_I2SMSK_RD | PSC_I2SMSK_TD)
+
+/* I2S Protocol Control Register. */
+#define PSC_I2SPCR_RC		(1 << 6)
+#define PSC_I2SPCR_RP		(1 << 5)
+#define PSC_I2SPCR_RS		(1 << 4)
+#define PSC_I2SPCR_TC		(1 << 2)
+#define PSC_I2SPCR_TP		(1 << 1)
+#define PSC_I2SPCR_TS		(1 << 0)
+
+/* I2S Status register (read only). */
+#define PSC_I2SSTAT_RF		(1 << 13)
+#define PSC_I2SSTAT_RE		(1 << 12)
+#define PSC_I2SSTAT_RR		(1 << 11)
+#define PSC_I2SSTAT_TF		(1 << 10)
+#define PSC_I2SSTAT_TE		(1 << 9)
+#define PSC_I2SSTAT_TR		(1 << 8)
+#define PSC_I2SSTAT_RB		(1 << 5)
+#define PSC_I2SSTAT_TB		(1 << 4)
+#define PSC_I2SSTAT_DI		(1 << 2)
+#define PSC_I2SSTAT_DR		(1 << 1)
+#define PSC_I2SSTAT_SR		(1 << 0)
+
+/* I2S Event Register. */
+#define PSC_I2SEVNT_RR		(1 << 13)
+#define PSC_I2SEVNT_RO		(1 << 12)
+#define PSC_I2SEVNT_RU		(1 << 11)
+#define PSC_I2SEVNT_TR		(1 << 10)
+#define PSC_I2SEVNT_TO		(1 << 9)
+#define PSC_I2SEVNT_TU		(1 << 8)
+#define PSC_I2SEVNT_RD		(1 << 5)
+#define PSC_I2SEVNT_TD		(1 << 4)
+
+/* PSC in SPI Mode. */
+typedef struct	psc_spi {
+	u32	psc_sel;
+	u32	psc_ctrl;
+	u32	psc_spicfg;
+	u32	psc_spimsk;
+	u32	psc_spipcr;
+	u32	psc_spistat;
+	u32	psc_spievent;
+	u32	psc_spitxrx;
+} psc_spi_t;
+
+/* SPI Config Register. */
+#define PSC_SPICFG_RT_MASK	(3 << 30)
+#define PSC_SPICFG_RT_FIFO1	(0 << 30)
+#define PSC_SPICFG_RT_FIFO2	(1 << 30)
+#define PSC_SPICFG_RT_FIFO4	(2 << 30)
+#define PSC_SPICFG_RT_FIFO8	(3 << 30)
+
+#define PSC_SPICFG_TT_MASK	(3 << 28)
+#define PSC_SPICFG_TT_FIFO1	(0 << 28)
+#define PSC_SPICFG_TT_FIFO2	(1 << 28)
+#define PSC_SPICFG_TT_FIFO4	(2 << 28)
+#define PSC_SPICFG_TT_FIFO8	(3 << 28)
+
+#define PSC_SPICFG_DD_DISABLE	(1 << 27)
+#define PSC_SPICFG_DE_ENABLE	(1 << 26)
+#define PSC_SPICFG_CLR_BAUD(x)	((x) & ~((0x3f) << 15))
+#define PSC_SPICFG_SET_BAUD(x)	(((x) & 0x3f) << 15)
+
+#define PSC_SPICFG_SET_DIV(x)	(((x) & 0x03) << 13)
+#define PSC_SPICFG_DIV2		0
+#define PSC_SPICFG_DIV4		1
+#define PSC_SPICFG_DIV8		2
+#define PSC_SPICFG_DIV16	3
+
+#define PSC_SPICFG_BI		(1 << 12)
+#define PSC_SPICFG_PSE		(1 << 11)
+#define PSC_SPICFG_CGE		(1 << 10)
+#define PSC_SPICFG_CDE		(1 << 9)
+
+#define PSC_SPICFG_CLR_LEN(x)	((x) & ~((0x1f) << 4))
+#define PSC_SPICFG_SET_LEN(x)	(((x-1) & 0x1f) << 4)
+
+#define PSC_SPICFG_LB		(1 << 3)
+#define PSC_SPICFG_MLF		(1 << 1)
+#define PSC_SPICFG_MO		(1 << 0)
+
+/* SPI Mask Register. */
+#define PSC_SPIMSK_MM		(1 << 16)
+#define PSC_SPIMSK_RR		(1 << 13)
+#define PSC_SPIMSK_RO		(1 << 12)
+#define PSC_SPIMSK_RU		(1 << 11)
+#define PSC_SPIMSK_TR		(1 << 10)
+#define PSC_SPIMSK_TO		(1 << 9)
+#define PSC_SPIMSK_TU		(1 << 8)
+#define PSC_SPIMSK_SD		(1 << 5)
+#define PSC_SPIMSK_MD		(1 << 4)
+#define PSC_SPIMSK_ALLMASK	(PSC_SPIMSK_MM | PSC_SPIMSK_RR | \
+				 PSC_SPIMSK_RO | PSC_SPIMSK_TO | \
+				 PSC_SPIMSK_TU | PSC_SPIMSK_SD | \
+				 PSC_SPIMSK_MD)
+
+/* SPI Protocol Control Register. */
+#define PSC_SPIPCR_RC		(1 << 6)
+#define PSC_SPIPCR_SP		(1 << 5)
+#define PSC_SPIPCR_SS		(1 << 4)
+#define PSC_SPIPCR_TC		(1 << 2)
+#define PSC_SPIPCR_MS		(1 << 0)
+
+/* SPI Status register (read only). */
+#define PSC_SPISTAT_RF		(1 << 13)
+#define PSC_SPISTAT_RE		(1 << 12)
+#define PSC_SPISTAT_RR		(1 << 11)
+#define PSC_SPISTAT_TF		(1 << 10)
+#define PSC_SPISTAT_TE		(1 << 9)
+#define PSC_SPISTAT_TR		(1 << 8)
+#define PSC_SPISTAT_SB		(1 << 5)
+#define PSC_SPISTAT_MB		(1 << 4)
+#define PSC_SPISTAT_DI		(1 << 2)
+#define PSC_SPISTAT_DR		(1 << 1)
+#define PSC_SPISTAT_SR		(1 << 0)
+
+/* SPI Event Register. */
+#define PSC_SPIEVNT_MM		(1 << 16)
+#define PSC_SPIEVNT_RR		(1 << 13)
+#define PSC_SPIEVNT_RO		(1 << 12)
+#define PSC_SPIEVNT_RU		(1 << 11)
+#define PSC_SPIEVNT_TR		(1 << 10)
+#define PSC_SPIEVNT_TO		(1 << 9)
+#define PSC_SPIEVNT_TU		(1 << 8)
+#define PSC_SPIEVNT_SD		(1 << 5)
+#define PSC_SPIEVNT_MD		(1 << 4)
+
+/* Transmit register control. */
+#define PSC_SPITXRX_LC		(1 << 29)
+#define PSC_SPITXRX_SR		(1 << 28)
+
+/* SMBus Config Register. */
+#define PSC_SMBCFG_RT_MASK	(3 << 30)
+#define PSC_SMBCFG_RT_FIFO1	(0 << 30)
+#define PSC_SMBCFG_RT_FIFO2	(1 << 30)
+#define PSC_SMBCFG_RT_FIFO4	(2 << 30)
+#define PSC_SMBCFG_RT_FIFO8	(3 << 30)
+
+#define PSC_SMBCFG_TT_MASK	(3 << 28)
+#define PSC_SMBCFG_TT_FIFO1	(0 << 28)
+#define PSC_SMBCFG_TT_FIFO2	(1 << 28)
+#define PSC_SMBCFG_TT_FIFO4	(2 << 28)
+#define PSC_SMBCFG_TT_FIFO8	(3 << 28)
+
+#define PSC_SMBCFG_DD_DISABLE	(1 << 27)
+#define PSC_SMBCFG_DE_ENABLE	(1 << 26)
+
+#define PSC_SMBCFG_SET_DIV(x)	(((x) & 0x03) << 13)
+#define PSC_SMBCFG_DIV2		0
+#define PSC_SMBCFG_DIV4		1
+#define PSC_SMBCFG_DIV8		2
+#define PSC_SMBCFG_DIV16	3
+
+#define PSC_SMBCFG_GCE		(1 << 9)
+#define PSC_SMBCFG_SFM		(1 << 8)
+
+#define PSC_SMBCFG_SET_SLV(x)	(((x) & 0x7f) << 1)
+
+/* SMBus Mask Register. */
+#define PSC_SMBMSK_DN		(1 << 30)
+#define PSC_SMBMSK_AN		(1 << 29)
+#define PSC_SMBMSK_AL		(1 << 28)
+#define PSC_SMBMSK_RR		(1 << 13)
+#define PSC_SMBMSK_RO		(1 << 12)
+#define PSC_SMBMSK_RU		(1 << 11)
+#define PSC_SMBMSK_TR		(1 << 10)
+#define PSC_SMBMSK_TO		(1 << 9)
+#define PSC_SMBMSK_TU		(1 << 8)
+#define PSC_SMBMSK_SD		(1 << 5)
+#define PSC_SMBMSK_MD		(1 << 4)
+#define PSC_SMBMSK_ALLMASK	(PSC_SMBMSK_DN | PSC_SMBMSK_AN | \
+				 PSC_SMBMSK_AL | PSC_SMBMSK_RR | \
+				 PSC_SMBMSK_RO | PSC_SMBMSK_TO | \
+				 PSC_SMBMSK_TU | PSC_SMBMSK_SD | \
+				 PSC_SMBMSK_MD)
+
+/* SMBus Protocol Control Register. */
+#define PSC_SMBPCR_DC		(1 << 2)
+#define PSC_SMBPCR_MS		(1 << 0)
+
+/* SMBus Status register (read only). */
+#define PSC_SMBSTAT_BB		(1 << 28)
+#define PSC_SMBSTAT_RF		(1 << 13)
+#define PSC_SMBSTAT_RE		(1 << 12)
+#define PSC_SMBSTAT_RR		(1 << 11)
+#define PSC_SMBSTAT_TF		(1 << 10)
+#define PSC_SMBSTAT_TE		(1 << 9)
+#define PSC_SMBSTAT_TR		(1 << 8)
+#define PSC_SMBSTAT_SB		(1 << 5)
+#define PSC_SMBSTAT_MB		(1 << 4)
+#define PSC_SMBSTAT_DI		(1 << 2)
+#define PSC_SMBSTAT_DR		(1 << 1)
+#define PSC_SMBSTAT_SR		(1 << 0)
+
+/* SMBus Event Register. */
+#define PSC_SMBEVNT_DN		(1 << 30)
+#define PSC_SMBEVNT_AN		(1 << 29)
+#define PSC_SMBEVNT_AL		(1 << 28)
+#define PSC_SMBEVNT_RR		(1 << 13)
+#define PSC_SMBEVNT_RO		(1 << 12)
+#define PSC_SMBEVNT_RU		(1 << 11)
+#define PSC_SMBEVNT_TR		(1 << 10)
+#define PSC_SMBEVNT_TO		(1 << 9)
+#define PSC_SMBEVNT_TU		(1 << 8)
+#define PSC_SMBEVNT_SD		(1 << 5)
+#define PSC_SMBEVNT_MD		(1 << 4)
+#define PSC_SMBEVNT_ALLCLR	(PSC_SMBEVNT_DN | PSC_SMBEVNT_AN | \
+				 PSC_SMBEVNT_AL | PSC_SMBEVNT_RR | \
+				 PSC_SMBEVNT_RO | PSC_SMBEVNT_TO | \
+				 PSC_SMBEVNT_TU | PSC_SMBEVNT_SD | \
+				 PSC_SMBEVNT_MD)
+
+/* Transmit register control. */
+#define PSC_SMBTXRX_RSR		(1 << 28)
+#define PSC_SMBTXRX_STP		(1 << 29)
+#define PSC_SMBTXRX_DATAMASK	0xff
+
+/* SMBus protocol timers register. */
+#define PSC_SMBTMR_SET_TH(x)	(((x) & 0x03) << 30)
+#define PSC_SMBTMR_SET_PS(x)	(((x) & 0x1f) << 25)
+#define PSC_SMBTMR_SET_PU(x)	(((x) & 0x1f) << 20)
+#define PSC_SMBTMR_SET_SH(x)	(((x) & 0x1f) << 15)
+#define PSC_SMBTMR_SET_SU(x)	(((x) & 0x1f) << 10)
+#define PSC_SMBTMR_SET_CL(x)	(((x) & 0x1f) << 5)
+#define PSC_SMBTMR_SET_CH(x)	(((x) & 0x1f) << 0)
+
+#endif /* _AU1000_PSC_H_ */
diff --git a/arch/mips/include/asm/mach-au1x00/cpu-feature-overrides.h b/arch/mips/include/asm/mach-au1x00/cpu-feature-overrides.h
new file mode 100644
index 000000000..3c200303a
--- /dev/null
+++ b/arch/mips/include/asm/mach-au1x00/cpu-feature-overrides.h
@@ -0,0 +1,93 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+
+#ifndef __ASM_MACH_AU1X00_CPU_FEATURE_OVERRIDES_H
+#define __ASM_MACH_AU1X00_CPU_FEATURE_OVERRIDES_H
+
+#define cpu_has_tlb			1
+#define cpu_has_ftlb			0
+#define cpu_has_tlbinv			0
+#define cpu_has_segments		0
+#define cpu_has_eva			0
+#define cpu_has_htw			0
+#define cpu_has_ldpte			0
+#define cpu_has_rixiex			0
+#define cpu_has_maar			0
+#define cpu_has_rw_llb			0
+#define cpu_has_3kex			0
+#define cpu_has_4kex			1
+#define cpu_has_3k_cache		0
+#define cpu_has_4k_cache		1
+#define cpu_has_fpu			0
+#define cpu_has_32fpr			0
+#define cpu_has_counter			1
+#define cpu_has_watch			1
+#define cpu_has_divec			1
+#define cpu_has_vce			0
+#define cpu_has_cache_cdex_p		0
+#define cpu_has_cache_cdex_s		0
+#define cpu_has_prefetch		1
+#define cpu_has_mcheck			1
+#define cpu_has_ejtag			1
+#define cpu_has_llsc			1
+#define cpu_has_guestctl0ext		0
+#define cpu_has_guestctl1		0
+#define cpu_has_guestctl2		0
+#define cpu_has_guestid			0
+#define cpu_has_drg			0
+#define cpu_has_mips16			0
+#define cpu_has_mips16e2		0
+#define cpu_has_mdmx			0
+#define cpu_has_mips3d			0
+#define cpu_has_smartmips		0
+#define cpu_has_rixi			0
+#define cpu_has_mmips			0
+#define cpu_has_lpa			0
+#define cpu_has_mhv			0
+#define cpu_has_vtag_icache		0
+#define cpu_has_dc_aliases		0
+#define cpu_has_ic_fills_f_dc		1
+#define cpu_has_pindexed_dcache		0
+#define cpu_has_mips32r1		1
+#define cpu_has_mips32r2		0
+#define cpu_has_mips32r6		0
+#define cpu_has_mips64r1		0
+#define cpu_has_mips64r2		0
+#define cpu_has_mips64r6		0
+#define cpu_has_dsp			0
+#define cpu_has_dsp2			0
+#define cpu_has_dsp3			0
+#define cpu_has_mipsmt			0
+#define cpu_has_vp			0
+#define cpu_has_userlocal		0
+#define cpu_has_nofpuex			0
+#define cpu_has_64bits			0
+#define cpu_has_64bit_zero_reg		0
+#define cpu_has_vint			0
+#define cpu_has_veic			0
+#define cpu_has_inclusive_pcaches	0
+
+#define cpu_dcache_line_size()		32
+#define cpu_icache_line_size()		32
+#define cpu_scache_line_size()		0
+#define cpu_tcache_line_size()		0
+
+#define cpu_has_perf_cntr_intr_bit	0
+#define cpu_has_vz			0
+#define cpu_has_msa			0
+#define cpu_has_ufr			0
+#define cpu_has_fre			0
+#define cpu_has_cdmm			0
+#define cpu_has_small_pages		0
+#define cpu_has_nan_legacy		1
+#define cpu_has_nan_2008		1
+#define cpu_has_ebase_wg		0
+#define cpu_has_badinstr		0
+#define cpu_has_badinstrp		0
+#define cpu_has_contextconfig		0
+#define cpu_has_perf			0
+
+#endif /* __ASM_MACH_AU1X00_CPU_FEATURE_OVERRIDES_H */
diff --git a/arch/mips/include/asm/mach-au1x00/gpio-au1000.h b/arch/mips/include/asm/mach-au1x00/gpio-au1000.h
new file mode 100644
index 000000000..adde1fa50
--- /dev/null
+++ b/arch/mips/include/asm/mach-au1x00/gpio-au1000.h
@@ -0,0 +1,532 @@
+/*
+ * GPIO functions for Au1000, Au1500, Au1100, Au1550, Au1200
+ *
+ * Copyright (c) 2009 Manuel Lauss.
+ *
+ * Licensed under the terms outlined in the file COPYING.
+ */
+
+#ifndef _ALCHEMY_GPIO_AU1000_H_
+#define _ALCHEMY_GPIO_AU1000_H_
+
+#include <asm/mach-au1x00/au1000.h>
+
+/* The default GPIO numberspace as documented in the Alchemy manuals.
+ * GPIO0-31 from GPIO1 block,	GPIO200-215 from GPIO2 block.
+ */
+#define ALCHEMY_GPIO1_BASE	0
+#define ALCHEMY_GPIO2_BASE	200
+
+#define ALCHEMY_GPIO1_NUM	32
+#define ALCHEMY_GPIO2_NUM	16
+#define ALCHEMY_GPIO1_MAX	(ALCHEMY_GPIO1_BASE + ALCHEMY_GPIO1_NUM - 1)
+#define ALCHEMY_GPIO2_MAX	(ALCHEMY_GPIO2_BASE + ALCHEMY_GPIO2_NUM - 1)
+
+#define MAKE_IRQ(intc, off)	(AU1000_INTC##intc##_INT_BASE + (off))
+
+/* GPIO1 registers within SYS_ area */
+#define AU1000_SYS_TRIOUTRD	0x100
+#define AU1000_SYS_TRIOUTCLR	0x100
+#define AU1000_SYS_OUTPUTRD	0x108
+#define AU1000_SYS_OUTPUTSET	0x108
+#define AU1000_SYS_OUTPUTCLR	0x10C
+#define AU1000_SYS_PINSTATERD	0x110
+#define AU1000_SYS_PININPUTEN	0x110
+
+/* register offsets within GPIO2 block */
+#define AU1000_GPIO2_DIR	0x00
+#define AU1000_GPIO2_OUTPUT	0x08
+#define AU1000_GPIO2_PINSTATE	0x0C
+#define AU1000_GPIO2_INTENABLE	0x10
+#define AU1000_GPIO2_ENABLE	0x14
+
+struct gpio;
+
+static inline int au1000_gpio1_to_irq(int gpio)
+{
+	return MAKE_IRQ(1, gpio - ALCHEMY_GPIO1_BASE);
+}
+
+static inline int au1000_gpio2_to_irq(int gpio)
+{
+	return -ENXIO;
+}
+
+static inline int au1000_irq_to_gpio(int irq)
+{
+	if ((irq >= AU1000_GPIO0_INT) && (irq <= AU1000_GPIO31_INT))
+		return ALCHEMY_GPIO1_BASE + (irq - AU1000_GPIO0_INT) + 0;
+
+	return -ENXIO;
+}
+
+static inline int au1500_gpio1_to_irq(int gpio)
+{
+	gpio -= ALCHEMY_GPIO1_BASE;
+
+	switch (gpio) {
+	case 0 ... 15:
+	case 20:
+	case 23 ... 28: return MAKE_IRQ(1, gpio);
+	}
+
+	return -ENXIO;
+}
+
+static inline int au1500_gpio2_to_irq(int gpio)
+{
+	gpio -= ALCHEMY_GPIO2_BASE;
+
+	switch (gpio) {
+	case 0 ... 3:	return MAKE_IRQ(1, 16 + gpio - 0);
+	case 4 ... 5:	return MAKE_IRQ(1, 21 + gpio - 4);
+	case 6 ... 7:	return MAKE_IRQ(1, 29 + gpio - 6);
+	}
+
+	return -ENXIO;
+}
+
+static inline int au1500_irq_to_gpio(int irq)
+{
+	switch (irq) {
+	case AU1500_GPIO0_INT ... AU1500_GPIO15_INT:
+	case AU1500_GPIO20_INT:
+	case AU1500_GPIO23_INT ... AU1500_GPIO28_INT:
+		return ALCHEMY_GPIO1_BASE + (irq - AU1500_GPIO0_INT) + 0;
+	case AU1500_GPIO200_INT ... AU1500_GPIO203_INT:
+		return ALCHEMY_GPIO2_BASE + (irq - AU1500_GPIO200_INT) + 0;
+	case AU1500_GPIO204_INT ... AU1500_GPIO205_INT:
+		return ALCHEMY_GPIO2_BASE + (irq - AU1500_GPIO204_INT) + 4;
+	case AU1500_GPIO206_INT ... AU1500_GPIO207_INT:
+		return ALCHEMY_GPIO2_BASE + (irq - AU1500_GPIO206_INT) + 6;
+	case AU1500_GPIO208_215_INT:
+		return ALCHEMY_GPIO2_BASE + 8;
+	}
+
+	return -ENXIO;
+}
+
+static inline int au1100_gpio1_to_irq(int gpio)
+{
+	return MAKE_IRQ(1, gpio - ALCHEMY_GPIO1_BASE);
+}
+
+static inline int au1100_gpio2_to_irq(int gpio)
+{
+	gpio -= ALCHEMY_GPIO2_BASE;
+
+	if ((gpio >= 8) && (gpio <= 15))
+		return MAKE_IRQ(0, 29);		/* shared GPIO208_215 */
+
+	return -ENXIO;
+}
+
+static inline int au1100_irq_to_gpio(int irq)
+{
+	switch (irq) {
+	case AU1100_GPIO0_INT ... AU1100_GPIO31_INT:
+		return ALCHEMY_GPIO1_BASE + (irq - AU1100_GPIO0_INT) + 0;
+	case AU1100_GPIO208_215_INT:
+		return ALCHEMY_GPIO2_BASE + 8;
+	}
+
+	return -ENXIO;
+}
+
+static inline int au1550_gpio1_to_irq(int gpio)
+{
+	gpio -= ALCHEMY_GPIO1_BASE;
+
+	switch (gpio) {
+	case 0 ... 15:
+	case 20 ... 28: return MAKE_IRQ(1, gpio);
+	case 16 ... 17: return MAKE_IRQ(1, 18 + gpio - 16);
+	}
+
+	return -ENXIO;
+}
+
+static inline int au1550_gpio2_to_irq(int gpio)
+{
+	gpio -= ALCHEMY_GPIO2_BASE;
+
+	switch (gpio) {
+	case 0:		return MAKE_IRQ(1, 16);
+	case 1 ... 5:	return MAKE_IRQ(1, 17); /* shared GPIO201_205 */
+	case 6 ... 7:	return MAKE_IRQ(1, 29 + gpio - 6);
+	case 8 ... 15:	return MAKE_IRQ(1, 31); /* shared GPIO208_215 */
+	}
+
+	return -ENXIO;
+}
+
+static inline int au1550_irq_to_gpio(int irq)
+{
+	switch (irq) {
+	case AU1550_GPIO0_INT ... AU1550_GPIO15_INT:
+		return ALCHEMY_GPIO1_BASE + (irq - AU1550_GPIO0_INT) + 0;
+	case AU1550_GPIO200_INT:
+	case AU1550_GPIO201_205_INT:
+		return ALCHEMY_GPIO2_BASE + (irq - AU1550_GPIO200_INT) + 0;
+	case AU1550_GPIO16_INT ... AU1550_GPIO28_INT:
+		return ALCHEMY_GPIO1_BASE + (irq - AU1550_GPIO16_INT) + 16;
+	case AU1550_GPIO206_INT ... AU1550_GPIO208_215_INT:
+		return ALCHEMY_GPIO2_BASE + (irq - AU1550_GPIO206_INT) + 6;
+	}
+
+	return -ENXIO;
+}
+
+static inline int au1200_gpio1_to_irq(int gpio)
+{
+	return MAKE_IRQ(1, gpio - ALCHEMY_GPIO1_BASE);
+}
+
+static inline int au1200_gpio2_to_irq(int gpio)
+{
+	gpio -= ALCHEMY_GPIO2_BASE;
+
+	switch (gpio) {
+	case 0 ... 2:	return MAKE_IRQ(0, 5 + gpio - 0);
+	case 3:		return MAKE_IRQ(0, 22);
+	case 4 ... 7:	return MAKE_IRQ(0, 24 + gpio - 4);
+	case 8 ... 15:	return MAKE_IRQ(0, 28); /* shared GPIO208_215 */
+	}
+
+	return -ENXIO;
+}
+
+static inline int au1200_irq_to_gpio(int irq)
+{
+	switch (irq) {
+	case AU1200_GPIO0_INT ... AU1200_GPIO31_INT:
+		return ALCHEMY_GPIO1_BASE + (irq - AU1200_GPIO0_INT) + 0;
+	case AU1200_GPIO200_INT ... AU1200_GPIO202_INT:
+		return ALCHEMY_GPIO2_BASE + (irq - AU1200_GPIO200_INT) + 0;
+	case AU1200_GPIO203_INT:
+		return ALCHEMY_GPIO2_BASE + 3;
+	case AU1200_GPIO204_INT ... AU1200_GPIO208_215_INT:
+		return ALCHEMY_GPIO2_BASE + (irq - AU1200_GPIO204_INT) + 4;
+	}
+
+	return -ENXIO;
+}
+
+/*
+ * GPIO1 block macros for common linux gpio functions.
+ */
+static inline void alchemy_gpio1_set_value(int gpio, int v)
+{
+	unsigned long mask = 1 << (gpio - ALCHEMY_GPIO1_BASE);
+	unsigned long r = v ? AU1000_SYS_OUTPUTSET : AU1000_SYS_OUTPUTCLR;
+	alchemy_wrsys(mask, r);
+}
+
+static inline int alchemy_gpio1_get_value(int gpio)
+{
+	unsigned long mask = 1 << (gpio - ALCHEMY_GPIO1_BASE);
+	return alchemy_rdsys(AU1000_SYS_PINSTATERD) & mask;
+}
+
+static inline int alchemy_gpio1_direction_input(int gpio)
+{
+	unsigned long mask = 1 << (gpio - ALCHEMY_GPIO1_BASE);
+	alchemy_wrsys(mask, AU1000_SYS_TRIOUTCLR);
+	return 0;
+}
+
+static inline int alchemy_gpio1_direction_output(int gpio, int v)
+{
+	/* hardware switches to "output" mode when one of the two
+	 * "set_value" registers is accessed.
+	 */
+	alchemy_gpio1_set_value(gpio, v);
+	return 0;
+}
+
+static inline int alchemy_gpio1_is_valid(int gpio)
+{
+	return ((gpio >= ALCHEMY_GPIO1_BASE) && (gpio <= ALCHEMY_GPIO1_MAX));
+}
+
+static inline int alchemy_gpio1_to_irq(int gpio)
+{
+	switch (alchemy_get_cputype()) {
+	case ALCHEMY_CPU_AU1000:
+		return au1000_gpio1_to_irq(gpio);
+	case ALCHEMY_CPU_AU1100:
+		return au1100_gpio1_to_irq(gpio);
+	case ALCHEMY_CPU_AU1500:
+		return au1500_gpio1_to_irq(gpio);
+	case ALCHEMY_CPU_AU1550:
+		return au1550_gpio1_to_irq(gpio);
+	case ALCHEMY_CPU_AU1200:
+		return au1200_gpio1_to_irq(gpio);
+	}
+	return -ENXIO;
+}
+
+/* On Au1000, Au1500 and Au1100 GPIOs won't work as inputs before
+ * SYS_PININPUTEN is written to at least once.  On Au1550/Au1200/Au1300 this
+ * register enables use of GPIOs as wake source.
+ */
+static inline void alchemy_gpio1_input_enable(void)
+{
+	void __iomem *base = (void __iomem *)KSEG1ADDR(AU1000_SYS_PHYS_ADDR);
+	__raw_writel(0, base + 0x110);		/* the write op is key */
+	wmb();
+}
+
+/*
+ * GPIO2 block macros for common linux GPIO functions. The 'gpio'
+ * parameter must be in range of ALCHEMY_GPIO2_BASE..ALCHEMY_GPIO2_MAX.
+ */
+static inline void __alchemy_gpio2_mod_dir(int gpio, int to_out)
+{
+	void __iomem *base = (void __iomem *)KSEG1ADDR(AU1500_GPIO2_PHYS_ADDR);
+	unsigned long mask = 1 << (gpio - ALCHEMY_GPIO2_BASE);
+	unsigned long d = __raw_readl(base + AU1000_GPIO2_DIR);
+
+	if (to_out)
+		d |= mask;
+	else
+		d &= ~mask;
+	__raw_writel(d, base + AU1000_GPIO2_DIR);
+	wmb();
+}
+
+static inline void alchemy_gpio2_set_value(int gpio, int v)
+{
+	void __iomem *base = (void __iomem *)KSEG1ADDR(AU1500_GPIO2_PHYS_ADDR);
+	unsigned long mask;
+	mask = ((v) ? 0x00010001 : 0x00010000) << (gpio - ALCHEMY_GPIO2_BASE);
+	__raw_writel(mask, base + AU1000_GPIO2_OUTPUT);
+	wmb();
+}
+
+static inline int alchemy_gpio2_get_value(int gpio)
+{
+	void __iomem *base = (void __iomem *)KSEG1ADDR(AU1500_GPIO2_PHYS_ADDR);
+	return __raw_readl(base + AU1000_GPIO2_PINSTATE) &
+				(1 << (gpio - ALCHEMY_GPIO2_BASE));
+}
+
+static inline int alchemy_gpio2_direction_input(int gpio)
+{
+	unsigned long flags;
+	local_irq_save(flags);
+	__alchemy_gpio2_mod_dir(gpio, 0);
+	local_irq_restore(flags);
+	return 0;
+}
+
+static inline int alchemy_gpio2_direction_output(int gpio, int v)
+{
+	unsigned long flags;
+	alchemy_gpio2_set_value(gpio, v);
+	local_irq_save(flags);
+	__alchemy_gpio2_mod_dir(gpio, 1);
+	local_irq_restore(flags);
+	return 0;
+}
+
+static inline int alchemy_gpio2_is_valid(int gpio)
+{
+	return ((gpio >= ALCHEMY_GPIO2_BASE) && (gpio <= ALCHEMY_GPIO2_MAX));
+}
+
+static inline int alchemy_gpio2_to_irq(int gpio)
+{
+	switch (alchemy_get_cputype()) {
+	case ALCHEMY_CPU_AU1000:
+		return au1000_gpio2_to_irq(gpio);
+	case ALCHEMY_CPU_AU1100:
+		return au1100_gpio2_to_irq(gpio);
+	case ALCHEMY_CPU_AU1500:
+		return au1500_gpio2_to_irq(gpio);
+	case ALCHEMY_CPU_AU1550:
+		return au1550_gpio2_to_irq(gpio);
+	case ALCHEMY_CPU_AU1200:
+		return au1200_gpio2_to_irq(gpio);
+	}
+	return -ENXIO;
+}
+
+/**********************************************************************/
+
+/* GPIO2 shared interrupts and control */
+
+static inline void __alchemy_gpio2_mod_int(int gpio2, int en)
+{
+	void __iomem *base = (void __iomem *)KSEG1ADDR(AU1500_GPIO2_PHYS_ADDR);
+	unsigned long r = __raw_readl(base + AU1000_GPIO2_INTENABLE);
+	if (en)
+		r |= 1 << gpio2;
+	else
+		r &= ~(1 << gpio2);
+	__raw_writel(r, base + AU1000_GPIO2_INTENABLE);
+	wmb();
+}
+
+/**
+ * alchemy_gpio2_enable_int - Enable a GPIO2 pins' shared irq contribution.
+ * @gpio2:	The GPIO2 pin to activate (200...215).
+ *
+ * GPIO208-215 have one shared interrupt line to the INTC.  They are
+ * and'ed with a per-pin enable bit and finally or'ed together to form
+ * a single irq request (useful for active-high sources).
+ * With this function, a pins' individual contribution to the int request
+ * can be enabled.  As with all other GPIO-based interrupts, the INTC
+ * must be programmed to accept the GPIO208_215 interrupt as well.
+ *
+ * NOTE: Calling this macro is only necessary for GPIO208-215; all other
+ * GPIO2-based interrupts have their own request to the INTC.  Please
+ * consult your Alchemy databook for more information!
+ *
+ * NOTE: On the Au1550, GPIOs 201-205 also have a shared interrupt request
+ * line to the INTC, GPIO201_205.  This function can be used for those
+ * as well.
+ *
+ * NOTE: 'gpio2' parameter must be in range of the GPIO2 numberspace
+ * (200-215 by default). No sanity checks are made,
+ */
+static inline void alchemy_gpio2_enable_int(int gpio2)
+{
+	unsigned long flags;
+
+	gpio2 -= ALCHEMY_GPIO2_BASE;
+
+	/* Au1100/Au1500 have GPIO208-215 enable bits at 0..7 */
+	switch (alchemy_get_cputype()) {
+	case ALCHEMY_CPU_AU1100:
+	case ALCHEMY_CPU_AU1500:
+		gpio2 -= 8;
+	}
+
+	local_irq_save(flags);
+	__alchemy_gpio2_mod_int(gpio2, 1);
+	local_irq_restore(flags);
+}
+
+/**
+ * alchemy_gpio2_disable_int - Disable a GPIO2 pins' shared irq contribution.
+ * @gpio2:	The GPIO2 pin to activate (200...215).
+ *
+ * see function alchemy_gpio2_enable_int() for more information.
+ */
+static inline void alchemy_gpio2_disable_int(int gpio2)
+{
+	unsigned long flags;
+
+	gpio2 -= ALCHEMY_GPIO2_BASE;
+
+	/* Au1100/Au1500 have GPIO208-215 enable bits at 0..7 */
+	switch (alchemy_get_cputype()) {
+	case ALCHEMY_CPU_AU1100:
+	case ALCHEMY_CPU_AU1500:
+		gpio2 -= 8;
+	}
+
+	local_irq_save(flags);
+	__alchemy_gpio2_mod_int(gpio2, 0);
+	local_irq_restore(flags);
+}
+
+/**
+ * alchemy_gpio2_enable -  Activate GPIO2 block.
+ *
+ * The GPIO2 block must be enabled excplicitly to work.	 On systems
+ * where this isn't done by the bootloader, this macro can be used.
+ */
+static inline void alchemy_gpio2_enable(void)
+{
+	void __iomem *base = (void __iomem *)KSEG1ADDR(AU1500_GPIO2_PHYS_ADDR);
+	__raw_writel(3, base + AU1000_GPIO2_ENABLE);	/* reset, clock enabled */
+	wmb();
+	__raw_writel(1, base + AU1000_GPIO2_ENABLE);	/* clock enabled */
+	wmb();
+}
+
+/**
+ * alchemy_gpio2_disable - disable GPIO2 block.
+ *
+ * Disable and put GPIO2 block in low-power mode.
+ */
+static inline void alchemy_gpio2_disable(void)
+{
+	void __iomem *base = (void __iomem *)KSEG1ADDR(AU1500_GPIO2_PHYS_ADDR);
+	__raw_writel(2, base + AU1000_GPIO2_ENABLE);	/* reset, clock disabled */
+	wmb();
+}
+
+/**********************************************************************/
+
+/* wrappers for on-chip gpios; can be used before gpio chips have been
+ * registered with gpiolib.
+ */
+static inline int alchemy_gpio_direction_input(int gpio)
+{
+	return (gpio >= ALCHEMY_GPIO2_BASE) ?
+		alchemy_gpio2_direction_input(gpio) :
+		alchemy_gpio1_direction_input(gpio);
+}
+
+static inline int alchemy_gpio_direction_output(int gpio, int v)
+{
+	return (gpio >= ALCHEMY_GPIO2_BASE) ?
+		alchemy_gpio2_direction_output(gpio, v) :
+		alchemy_gpio1_direction_output(gpio, v);
+}
+
+static inline int alchemy_gpio_get_value(int gpio)
+{
+	return (gpio >= ALCHEMY_GPIO2_BASE) ?
+		alchemy_gpio2_get_value(gpio) :
+		alchemy_gpio1_get_value(gpio);
+}
+
+static inline void alchemy_gpio_set_value(int gpio, int v)
+{
+	if (gpio >= ALCHEMY_GPIO2_BASE)
+		alchemy_gpio2_set_value(gpio, v);
+	else
+		alchemy_gpio1_set_value(gpio, v);
+}
+
+static inline int alchemy_gpio_is_valid(int gpio)
+{
+	return (gpio >= ALCHEMY_GPIO2_BASE) ?
+		alchemy_gpio2_is_valid(gpio) :
+		alchemy_gpio1_is_valid(gpio);
+}
+
+static inline int alchemy_gpio_cansleep(int gpio)
+{
+	return 0;	/* Alchemy never gets tired */
+}
+
+static inline int alchemy_gpio_to_irq(int gpio)
+{
+	return (gpio >= ALCHEMY_GPIO2_BASE) ?
+		alchemy_gpio2_to_irq(gpio) :
+		alchemy_gpio1_to_irq(gpio);
+}
+
+static inline int alchemy_irq_to_gpio(int irq)
+{
+	switch (alchemy_get_cputype()) {
+	case ALCHEMY_CPU_AU1000:
+		return au1000_irq_to_gpio(irq);
+	case ALCHEMY_CPU_AU1100:
+		return au1100_irq_to_gpio(irq);
+	case ALCHEMY_CPU_AU1500:
+		return au1500_irq_to_gpio(irq);
+	case ALCHEMY_CPU_AU1550:
+		return au1550_irq_to_gpio(irq);
+	case ALCHEMY_CPU_AU1200:
+		return au1200_irq_to_gpio(irq);
+	}
+	return -ENXIO;
+}
+
+#endif /* _ALCHEMY_GPIO_AU1000_H_ */
diff --git a/arch/mips/include/asm/mach-au1x00/gpio-au1300.h b/arch/mips/include/asm/mach-au1x00/gpio-au1300.h
new file mode 100644
index 000000000..d16add7ba
--- /dev/null
+++ b/arch/mips/include/asm/mach-au1x00/gpio-au1300.h
@@ -0,0 +1,123 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * gpio-au1300.h -- GPIO control for Au1300 GPIC and compatibles.
+ *
+ * Copyright (c) 2009-2011 Manuel Lauss <manuel.lauss@googlemail.com>
+ */
+
+#ifndef _GPIO_AU1300_H_
+#define _GPIO_AU1300_H_
+
+#include <asm/addrspace.h>
+#include <asm/io.h>
+#include <asm/mach-au1x00/au1000.h>
+
+struct gpio;
+struct gpio_chip;
+
+/* with the current GPIC design, up to 128 GPIOs are possible.
+ * The only implementation so far is in the Au1300, which has 75 externally
+ * available GPIOs.
+ */
+#define AU1300_GPIO_BASE	0
+#define AU1300_GPIO_NUM		75
+#define AU1300_GPIO_MAX		(AU1300_GPIO_BASE + AU1300_GPIO_NUM - 1)
+
+#define AU1300_GPIC_ADDR	\
+	(void __iomem *)KSEG1ADDR(AU1300_GPIC_PHYS_ADDR)
+
+static inline int au1300_gpio_get_value(unsigned int gpio)
+{
+	void __iomem *roff = AU1300_GPIC_ADDR;
+	int bit;
+
+	gpio -= AU1300_GPIO_BASE;
+	roff += GPIC_GPIO_BANKOFF(gpio);
+	bit = GPIC_GPIO_TO_BIT(gpio);
+	return __raw_readl(roff + AU1300_GPIC_PINVAL) & bit;
+}
+
+static inline int au1300_gpio_direction_input(unsigned int gpio)
+{
+	void __iomem *roff = AU1300_GPIC_ADDR;
+	unsigned long bit;
+
+	gpio -= AU1300_GPIO_BASE;
+
+	roff += GPIC_GPIO_BANKOFF(gpio);
+	bit = GPIC_GPIO_TO_BIT(gpio);
+	__raw_writel(bit, roff + AU1300_GPIC_DEVCLR);
+	wmb();
+
+	return 0;
+}
+
+static inline int au1300_gpio_set_value(unsigned int gpio, int v)
+{
+	void __iomem *roff = AU1300_GPIC_ADDR;
+	unsigned long bit;
+
+	gpio -= AU1300_GPIO_BASE;
+
+	roff += GPIC_GPIO_BANKOFF(gpio);
+	bit = GPIC_GPIO_TO_BIT(gpio);
+	__raw_writel(bit, roff + (v ? AU1300_GPIC_PINVAL
+				    : AU1300_GPIC_PINVALCLR));
+	wmb();
+
+	return 0;
+}
+
+static inline int au1300_gpio_direction_output(unsigned int gpio, int v)
+{
+	/* hw switches to output automatically */
+	return au1300_gpio_set_value(gpio, v);
+}
+
+static inline int au1300_gpio_to_irq(unsigned int gpio)
+{
+	return AU1300_FIRST_INT + (gpio - AU1300_GPIO_BASE);
+}
+
+static inline int au1300_irq_to_gpio(unsigned int irq)
+{
+	return (irq - AU1300_FIRST_INT) + AU1300_GPIO_BASE;
+}
+
+static inline int au1300_gpio_is_valid(unsigned int gpio)
+{
+	int ret;
+
+	switch (alchemy_get_cputype()) {
+	case ALCHEMY_CPU_AU1300:
+		ret = ((gpio >= AU1300_GPIO_BASE) && (gpio <= AU1300_GPIO_MAX));
+		break;
+	default:
+		ret = 0;
+	}
+	return ret;
+}
+
+static inline int au1300_gpio_cansleep(unsigned int gpio)
+{
+	return 0;
+}
+
+/* hardware remembers gpio 0-63 levels on powerup */
+static inline int au1300_gpio_getinitlvl(unsigned int gpio)
+{
+	void __iomem *roff = AU1300_GPIC_ADDR;
+	unsigned long v;
+
+	if (unlikely(gpio > 63))
+		return 0;
+	else if (gpio > 31) {
+		gpio -= 32;
+		roff += 4;
+	}
+
+	v = __raw_readl(roff + AU1300_GPIC_RSTVAL);
+	return (v >> gpio) & 1;
+}
+
+#endif /* _GPIO_AU1300_H_ */
diff --git a/arch/mips/include/asm/mach-au1x00/prom.h b/arch/mips/include/asm/mach-au1x00/prom.h
new file mode 100644
index 000000000..c62ee0246
--- /dev/null
+++ b/arch/mips/include/asm/mach-au1x00/prom.h
@@ -0,0 +1,13 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __AU1X00_PROM_H
+#define __AU1X00_PROM_H
+
+extern int prom_argc;
+extern char **prom_argv;
+extern char **prom_envp;
+
+extern void prom_init_cmdline(void);
+extern char *prom_getenv(char *envname);
+extern int prom_get_ethernet_addr(char *ethernet_addr);
+
+#endif
diff --git a/arch/mips/include/asm/mach-bcm47xx/bcm47xx.h b/arch/mips/include/asm/mach-bcm47xx/bcm47xx.h
new file mode 100644
index 000000000..93817bfb7
--- /dev/null
+++ b/arch/mips/include/asm/mach-bcm47xx/bcm47xx.h
@@ -0,0 +1,38 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2007 Aurelien Jarno <aurelien@aurel32.net>
+ */
+
+#ifndef __ASM_BCM47XX_H
+#define __ASM_BCM47XX_H
+
+#include <linux/ssb/ssb.h>
+#include <linux/bcma/bcma.h>
+#include <linux/bcma/bcma_soc.h>
+#include <linux/bcm47xx_nvram.h>
+#include <linux/bcm47xx_sprom.h>
+
+enum bcm47xx_bus_type {
+#ifdef CONFIG_BCM47XX_SSB
+	BCM47XX_BUS_TYPE_SSB,
+#endif
+#ifdef CONFIG_BCM47XX_BCMA
+	BCM47XX_BUS_TYPE_BCMA,
+#endif
+};
+
+union bcm47xx_bus {
+#ifdef CONFIG_BCM47XX_SSB
+	struct ssb_bus ssb;
+#endif
+#ifdef CONFIG_BCM47XX_BCMA
+	struct bcma_soc bcma;
+#endif
+};
+
+extern union bcm47xx_bus bcm47xx_bus;
+extern enum bcm47xx_bus_type bcm47xx_bus_type;
+
+void bcm47xx_set_system_type(u16 chip_id);
+
+#endif /* __ASM_BCM47XX_H */
diff --git a/arch/mips/include/asm/mach-bcm47xx/bcm47xx_board.h b/arch/mips/include/asm/mach-bcm47xx/bcm47xx_board.h
new file mode 100644
index 000000000..30f4114ab
--- /dev/null
+++ b/arch/mips/include/asm/mach-bcm47xx/bcm47xx_board.h
@@ -0,0 +1,145 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __BCM47XX_BOARD_H
+#define __BCM47XX_BOARD_H
+
+enum bcm47xx_board {
+	BCM47XX_BOARD_ASUS_RTAC66U,
+	BCM47XX_BOARD_ASUS_RTN10,
+	BCM47XX_BOARD_ASUS_RTN10D,
+	BCM47XX_BOARD_ASUS_RTN10U,
+	BCM47XX_BOARD_ASUS_RTN12,
+	BCM47XX_BOARD_ASUS_RTN12B1,
+	BCM47XX_BOARD_ASUS_RTN12C1,
+	BCM47XX_BOARD_ASUS_RTN12D1,
+	BCM47XX_BOARD_ASUS_RTN12HP,
+	BCM47XX_BOARD_ASUS_RTN15U,
+	BCM47XX_BOARD_ASUS_RTN16,
+	BCM47XX_BOARD_ASUS_RTN53,
+	BCM47XX_BOARD_ASUS_RTN66U,
+	BCM47XX_BOARD_ASUS_WL300G,
+	BCM47XX_BOARD_ASUS_WL320GE,
+	BCM47XX_BOARD_ASUS_WL330GE,
+	BCM47XX_BOARD_ASUS_WL500G,
+	BCM47XX_BOARD_ASUS_WL500GD,
+	BCM47XX_BOARD_ASUS_WL500GPV1,
+	BCM47XX_BOARD_ASUS_WL500GPV2,
+	BCM47XX_BOARD_ASUS_WL500W,
+	BCM47XX_BOARD_ASUS_WL520GC,
+	BCM47XX_BOARD_ASUS_WL520GU,
+	BCM47XX_BOARD_ASUS_WL700GE,
+	BCM47XX_BOARD_ASUS_WLHDD,
+
+	BCM47XX_BOARD_BELKIN_F7D3301,
+	BCM47XX_BOARD_BELKIN_F7D3302,
+	BCM47XX_BOARD_BELKIN_F7D4301,
+	BCM47XX_BOARD_BELKIN_F7D4302,
+	BCM47XX_BOARD_BELKIN_F7D4401,
+
+	BCM47XX_BOARD_BUFFALO_WBR2_G54,
+	BCM47XX_BOARD_BUFFALO_WHR2_A54G54,
+	BCM47XX_BOARD_BUFFALO_WHR_G125,
+	BCM47XX_BOARD_BUFFALO_WHR_G54S,
+	BCM47XX_BOARD_BUFFALO_WHR_HP_G54,
+	BCM47XX_BOARD_BUFFALO_WLA2_G54L,
+	BCM47XX_BOARD_BUFFALO_WZR_G300N,
+	BCM47XX_BOARD_BUFFALO_WZR_RS_G54,
+	BCM47XX_BOARD_BUFFALO_WZR_RS_G54HP,
+
+	BCM47XX_BOARD_CISCO_M10V1,
+	BCM47XX_BOARD_CISCO_M20V1,
+
+	BCM47XX_BOARD_DELL_TM2300,
+
+	BCM47XX_BOARD_DLINK_DIR130,
+	BCM47XX_BOARD_DLINK_DIR330,
+
+	BCM47XX_BOARD_HUAWEI_E970,
+
+	BCM47XX_BOARD_LINKSYS_E900V1,
+	BCM47XX_BOARD_LINKSYS_E1000V1,
+	BCM47XX_BOARD_LINKSYS_E1000V2,
+	BCM47XX_BOARD_LINKSYS_E1000V21,
+	BCM47XX_BOARD_LINKSYS_E1200V2,
+	BCM47XX_BOARD_LINKSYS_E2000V1,
+	BCM47XX_BOARD_LINKSYS_E3000V1,
+	BCM47XX_BOARD_LINKSYS_E3200V1,
+	BCM47XX_BOARD_LINKSYS_E4200V1,
+	BCM47XX_BOARD_LINKSYS_WRT150NV1,
+	BCM47XX_BOARD_LINKSYS_WRT150NV11,
+	BCM47XX_BOARD_LINKSYS_WRT160NV1,
+	BCM47XX_BOARD_LINKSYS_WRT160NV3,
+	BCM47XX_BOARD_LINKSYS_WRT300N_V1,
+	BCM47XX_BOARD_LINKSYS_WRT300NV11,
+	BCM47XX_BOARD_LINKSYS_WRT310NV1,
+	BCM47XX_BOARD_LINKSYS_WRT310NV2,
+	BCM47XX_BOARD_LINKSYS_WRT320N_V1,
+	BCM47XX_BOARD_LINKSYS_WRT54G3GV2,
+	BCM47XX_BOARD_LINKSYS_WRT54G_TYPE_0101,
+	BCM47XX_BOARD_LINKSYS_WRT54G_TYPE_0467,
+	BCM47XX_BOARD_LINKSYS_WRT54G_TYPE_0708,
+	BCM47XX_BOARD_LINKSYS_WRT600N_V11,
+	BCM47XX_BOARD_LINKSYS_WRT610NV1,
+	BCM47XX_BOARD_LINKSYS_WRT610NV2,
+	BCM47XX_BOARD_LINKSYS_WRTSL54GS,
+
+	BCM47XX_BOARD_LUXUL_ABR_4400_V1,
+	BCM47XX_BOARD_LUXUL_XAP_310_V1,
+	BCM47XX_BOARD_LUXUL_XAP_1210_V1,
+	BCM47XX_BOARD_LUXUL_XAP_1230_V1,
+	BCM47XX_BOARD_LUXUL_XAP_1240_V1,
+	BCM47XX_BOARD_LUXUL_XAP_1500_V1,
+	BCM47XX_BOARD_LUXUL_XBR_4400_V1,
+	BCM47XX_BOARD_LUXUL_XVW_P30_V1,
+	BCM47XX_BOARD_LUXUL_XWR_600_V1,
+	BCM47XX_BOARD_LUXUL_XWR_1750_V1,
+
+	BCM47XX_BOARD_MICROSOFT_MN700,
+
+	BCM47XX_BOARD_MOTOROLA_WE800G,
+	BCM47XX_BOARD_MOTOROLA_WR850GP,
+	BCM47XX_BOARD_MOTOROLA_WR850GV2V3,
+
+	BCM47XX_BOARD_NETGEAR_R6200_V1,
+	BCM47XX_BOARD_NETGEAR_R6300_V1,
+	BCM47XX_BOARD_NETGEAR_WGR614V8,
+	BCM47XX_BOARD_NETGEAR_WGR614V9,
+	BCM47XX_BOARD_NETGEAR_WGR614_V10,
+	BCM47XX_BOARD_NETGEAR_WN2500RP_V1,
+	BCM47XX_BOARD_NETGEAR_WN2500RP_V2,
+	BCM47XX_BOARD_NETGEAR_WNDR3300,
+	BCM47XX_BOARD_NETGEAR_WNDR3400V1,
+	BCM47XX_BOARD_NETGEAR_WNDR3400V2,
+	BCM47XX_BOARD_NETGEAR_WNDR3400_V3,
+	BCM47XX_BOARD_NETGEAR_WNDR3400VCNA,
+	BCM47XX_BOARD_NETGEAR_WNDR3700V3,
+	BCM47XX_BOARD_NETGEAR_WNDR4000,
+	BCM47XX_BOARD_NETGEAR_WNDR4500V1,
+	BCM47XX_BOARD_NETGEAR_WNDR4500V2,
+	BCM47XX_BOARD_NETGEAR_WNR1000_V3,
+	BCM47XX_BOARD_NETGEAR_WNR2000,
+	BCM47XX_BOARD_NETGEAR_WNR3500L,
+	BCM47XX_BOARD_NETGEAR_WNR3500L_V2,
+	BCM47XX_BOARD_NETGEAR_WNR3500U,
+	BCM47XX_BOARD_NETGEAR_WNR3500V2,
+	BCM47XX_BOARD_NETGEAR_WNR3500V2VC,
+	BCM47XX_BOARD_NETGEAR_WNR834BV2,
+
+	BCM47XX_BOARD_PHICOMM_M1,
+
+	BCM47XX_BOARD_SIEMENS_SE505V2,
+
+	BCM47XX_BOARD_SIMPLETECH_SIMPLESHARE,
+
+	BCM47XX_BOARD_ZTE_H218N,
+
+	BCM47XX_BOARD_UNKNOWN,
+	BCM47XX_BOARD_NO,
+};
+
+#define BCM47XX_BOARD_MAX_NAME 30
+
+void bcm47xx_board_detect(void);
+enum bcm47xx_board bcm47xx_board_get(void);
+const char *bcm47xx_board_get_name(void);
+
+#endif /* __BCM47XX_BOARD_H */
diff --git a/arch/mips/include/asm/mach-bcm47xx/cpu-feature-overrides.h b/arch/mips/include/asm/mach-bcm47xx/cpu-feature-overrides.h
new file mode 100644
index 000000000..69899c1e1
--- /dev/null
+++ b/arch/mips/include/asm/mach-bcm47xx/cpu-feature-overrides.h
@@ -0,0 +1,82 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_MACH_BCM47XX_CPU_FEATURE_OVERRIDES_H
+#define __ASM_MACH_BCM47XX_CPU_FEATURE_OVERRIDES_H
+
+#define cpu_has_tlb			1
+#define cpu_has_4kex			1
+#define cpu_has_3k_cache		0
+#define cpu_has_4k_cache		1
+#define cpu_has_fpu			0
+#define cpu_has_32fpr			0
+#define cpu_has_counter			1
+#if defined(CONFIG_BCM47XX_BCMA) && !defined(CONFIG_BCM47XX_SSB)
+#define cpu_has_watch			1
+#elif defined(CONFIG_BCM47XX_SSB) && !defined(CONFIG_BCM47XX_BCMA)
+#define cpu_has_watch			0
+#endif
+#define cpu_has_divec			1
+#define cpu_has_vce			0
+#define cpu_has_cache_cdex_p		0
+#define cpu_has_cache_cdex_s		0
+#define cpu_has_prefetch		1
+#define cpu_has_mcheck			1
+#define cpu_has_ejtag			1
+#define cpu_has_llsc			1
+
+/* cpu_has_mips16 */
+#define cpu_has_mdmx			0
+#define cpu_has_mips3d			0
+#define cpu_has_rixi			0
+#define cpu_has_mmips			0
+#define cpu_has_smartmips		0
+#define cpu_has_vtag_icache		0
+/* cpu_has_dc_aliases */
+#define cpu_has_ic_fills_f_dc		0
+#define cpu_has_pindexed_dcache		0
+#define cpu_icache_snoops_remote_store	0
+
+#define cpu_has_mips_2			1
+#define cpu_has_mips_3			0
+#define cpu_has_mips32r1		1
+#if defined(CONFIG_BCM47XX_BCMA) && !defined(CONFIG_BCM47XX_SSB)
+#define cpu_has_mips32r2		1
+#elif defined(CONFIG_BCM47XX_SSB) && !defined(CONFIG_BCM47XX_BCMA)
+#define cpu_has_mips32r2		0
+#endif
+#define cpu_has_mips64r1		0
+#define cpu_has_mips64r2		0
+
+#if defined(CONFIG_BCM47XX_BCMA) && !defined(CONFIG_BCM47XX_SSB)
+#define cpu_has_dsp			1
+#define cpu_has_dsp2			1
+#elif defined(CONFIG_BCM47XX_SSB) && !defined(CONFIG_BCM47XX_BCMA)
+#define cpu_has_dsp			0
+#define cpu_has_dsp2			0
+#endif
+#define cpu_has_mipsmt			0
+/* cpu_has_userlocal */
+
+#define cpu_has_nofpuex			0
+#define cpu_has_64bits			0
+#define cpu_has_64bit_zero_reg		0
+#if defined(CONFIG_BCM47XX_BCMA) && !defined(CONFIG_BCM47XX_SSB)
+#define cpu_has_vint			1
+#elif defined(CONFIG_BCM47XX_SSB) && !defined(CONFIG_BCM47XX_BCMA)
+#define cpu_has_vint			0
+#endif
+#define cpu_has_veic			0
+#define cpu_has_inclusive_pcaches	0
+
+#if defined(CONFIG_BCM47XX_BCMA) && !defined(CONFIG_BCM47XX_SSB)
+#define cpu_dcache_line_size()		32
+#define cpu_icache_line_size()		32
+#define cpu_has_perf_cntr_intr_bit	1
+#elif defined(CONFIG_BCM47XX_SSB) && !defined(CONFIG_BCM47XX_BCMA)
+#define cpu_dcache_line_size()		16
+#define cpu_icache_line_size()		16
+#define cpu_has_perf_cntr_intr_bit	0
+#endif
+#define cpu_scache_line_size()		0
+#define cpu_has_vz			0
+
+#endif /* __ASM_MACH_BCM47XX_CPU_FEATURE_OVERRIDES_H */
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_board.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_board.h
new file mode 100644
index 000000000..1d19a726f
--- /dev/null
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_board.h
@@ -0,0 +1,13 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef BCM63XX_BOARD_H_
+#define BCM63XX_BOARD_H_
+
+const char *board_get_name(void);
+
+void board_prom_init(void);
+
+void board_setup(void);
+
+int board_register_devices(void);
+
+#endif /* ! BCM63XX_BOARD_H_ */
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
new file mode 100644
index 000000000..1cad18e66
--- /dev/null
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
@@ -0,0 +1,1068 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef BCM63XX_CPU_H_
+#define BCM63XX_CPU_H_
+
+#include <linux/types.h>
+#include <linux/init.h>
+
+/*
+ * Macro to fetch bcm63xx cpu id and revision, should be optimized at
+ * compile time if only one CPU support is enabled (idea stolen from
+ * arm mach-types)
+ */
+#define BCM3368_CPU_ID		0x3368
+#define BCM6328_CPU_ID		0x6328
+#define BCM6338_CPU_ID		0x6338
+#define BCM6345_CPU_ID		0x6345
+#define BCM6348_CPU_ID		0x6348
+#define BCM6358_CPU_ID		0x6358
+#define BCM6362_CPU_ID		0x6362
+#define BCM6368_CPU_ID		0x6368
+
+void __init bcm63xx_cpu_init(void);
+u8 bcm63xx_get_cpu_rev(void);
+unsigned int bcm63xx_get_cpu_freq(void);
+
+static inline u16 __pure __bcm63xx_get_cpu_id(const u16 cpu_id)
+{
+	switch (cpu_id) {
+#ifdef CONFIG_BCM63XX_CPU_3368
+		case BCM3368_CPU_ID:
+#endif
+
+#ifdef CONFIG_BCM63XX_CPU_6328
+		case BCM6328_CPU_ID:
+#endif
+
+#ifdef CONFIG_BCM63XX_CPU_6338
+		case BCM6338_CPU_ID:
+#endif
+
+#ifdef CONFIG_BCM63XX_CPU_6345
+		case BCM6345_CPU_ID:
+#endif
+
+#ifdef CONFIG_BCM63XX_CPU_6348
+		case BCM6348_CPU_ID:
+#endif
+
+#ifdef CONFIG_BCM63XX_CPU_6358
+		case BCM6358_CPU_ID:
+#endif
+
+#ifdef CONFIG_BCM63XX_CPU_6362
+		case BCM6362_CPU_ID:
+#endif
+
+#ifdef CONFIG_BCM63XX_CPU_6368
+		case BCM6368_CPU_ID:
+#endif
+		break;
+	default:
+		unreachable();
+	}
+
+	return cpu_id;
+}
+
+extern u16 bcm63xx_cpu_id;
+
+static inline u16 __pure bcm63xx_get_cpu_id(void)
+{
+	const u16 cpu_id = bcm63xx_cpu_id;
+
+	return __bcm63xx_get_cpu_id(cpu_id);
+}
+
+#define BCMCPU_IS_3368()	(bcm63xx_get_cpu_id() == BCM3368_CPU_ID)
+#define BCMCPU_IS_6328()	(bcm63xx_get_cpu_id() == BCM6328_CPU_ID)
+#define BCMCPU_IS_6338()	(bcm63xx_get_cpu_id() == BCM6338_CPU_ID)
+#define BCMCPU_IS_6345()	(bcm63xx_get_cpu_id() == BCM6345_CPU_ID)
+#define BCMCPU_IS_6348()	(bcm63xx_get_cpu_id() == BCM6348_CPU_ID)
+#define BCMCPU_IS_6358()	(bcm63xx_get_cpu_id() == BCM6358_CPU_ID)
+#define BCMCPU_IS_6362()	(bcm63xx_get_cpu_id() == BCM6362_CPU_ID)
+#define BCMCPU_IS_6368()	(bcm63xx_get_cpu_id() == BCM6368_CPU_ID)
+
+/*
+ * While registers sets are (mostly) the same across 63xx CPU, base
+ * address of these sets do change.
+ */
+enum bcm63xx_regs_set {
+	RSET_DSL_LMEM = 0,
+	RSET_PERF,
+	RSET_TIMER,
+	RSET_WDT,
+	RSET_UART0,
+	RSET_UART1,
+	RSET_GPIO,
+	RSET_SPI,
+	RSET_HSSPI,
+	RSET_UDC0,
+	RSET_OHCI0,
+	RSET_OHCI_PRIV,
+	RSET_USBH_PRIV,
+	RSET_USBD,
+	RSET_USBDMA,
+	RSET_MPI,
+	RSET_PCMCIA,
+	RSET_PCIE,
+	RSET_DSL,
+	RSET_ENET0,
+	RSET_ENET1,
+	RSET_ENETDMA,
+	RSET_ENETDMAC,
+	RSET_ENETDMAS,
+	RSET_ENETSW,
+	RSET_EHCI0,
+	RSET_SDRAM,
+	RSET_MEMC,
+	RSET_DDR,
+	RSET_M2M,
+	RSET_ATM,
+	RSET_XTM,
+	RSET_XTMDMA,
+	RSET_XTMDMAC,
+	RSET_XTMDMAS,
+	RSET_PCM,
+	RSET_PCMDMA,
+	RSET_PCMDMAC,
+	RSET_PCMDMAS,
+	RSET_RNG,
+	RSET_MISC
+};
+
+#define RSET_DSL_LMEM_SIZE		(64 * 1024 * 4)
+#define RSET_DSL_SIZE			4096
+#define RSET_WDT_SIZE			12
+#define BCM_6338_RSET_SPI_SIZE		64
+#define BCM_6348_RSET_SPI_SIZE		64
+#define BCM_6358_RSET_SPI_SIZE		1804
+#define BCM_6368_RSET_SPI_SIZE		1804
+#define RSET_ENET_SIZE			2048
+#define RSET_ENETDMA_SIZE		256
+#define RSET_6345_ENETDMA_SIZE		64
+#define RSET_ENETDMAC_SIZE(chans)	(16 * (chans))
+#define RSET_ENETDMAS_SIZE(chans)	(16 * (chans))
+#define RSET_ENETSW_SIZE		65536
+#define RSET_UART_SIZE			24
+#define RSET_HSSPI_SIZE			1536
+#define RSET_UDC_SIZE			256
+#define RSET_OHCI_SIZE			256
+#define RSET_EHCI_SIZE			256
+#define RSET_USBD_SIZE			256
+#define RSET_USBDMA_SIZE		1280
+#define RSET_PCMCIA_SIZE		12
+#define RSET_M2M_SIZE			256
+#define RSET_ATM_SIZE			4096
+#define RSET_XTM_SIZE			10240
+#define RSET_XTMDMA_SIZE		256
+#define RSET_XTMDMAC_SIZE(chans)	(16 * (chans))
+#define RSET_XTMDMAS_SIZE(chans)	(16 * (chans))
+#define RSET_RNG_SIZE			20
+
+/*
+ * 3368 register sets base address
+ */
+#define BCM_3368_DSL_LMEM_BASE		(0xdeadbeef)
+#define BCM_3368_PERF_BASE		(0xfff8c000)
+#define BCM_3368_TIMER_BASE		(0xfff8c040)
+#define BCM_3368_WDT_BASE		(0xfff8c080)
+#define BCM_3368_UART0_BASE		(0xfff8c100)
+#define BCM_3368_UART1_BASE		(0xfff8c120)
+#define BCM_3368_GPIO_BASE		(0xfff8c080)
+#define BCM_3368_SPI_BASE		(0xfff8c800)
+#define BCM_3368_HSSPI_BASE		(0xdeadbeef)
+#define BCM_3368_UDC0_BASE		(0xdeadbeef)
+#define BCM_3368_USBDMA_BASE		(0xdeadbeef)
+#define BCM_3368_OHCI0_BASE		(0xdeadbeef)
+#define BCM_3368_OHCI_PRIV_BASE		(0xdeadbeef)
+#define BCM_3368_USBH_PRIV_BASE		(0xdeadbeef)
+#define BCM_3368_USBD_BASE		(0xdeadbeef)
+#define BCM_3368_MPI_BASE		(0xfff80000)
+#define BCM_3368_PCMCIA_BASE		(0xfff80054)
+#define BCM_3368_PCIE_BASE		(0xdeadbeef)
+#define BCM_3368_SDRAM_REGS_BASE	(0xdeadbeef)
+#define BCM_3368_DSL_BASE		(0xdeadbeef)
+#define BCM_3368_UBUS_BASE		(0xdeadbeef)
+#define BCM_3368_ENET0_BASE		(0xfff98000)
+#define BCM_3368_ENET1_BASE		(0xfff98800)
+#define BCM_3368_ENETDMA_BASE		(0xfff99800)
+#define BCM_3368_ENETDMAC_BASE		(0xfff99900)
+#define BCM_3368_ENETDMAS_BASE		(0xfff99a00)
+#define BCM_3368_ENETSW_BASE		(0xdeadbeef)
+#define BCM_3368_EHCI0_BASE		(0xdeadbeef)
+#define BCM_3368_SDRAM_BASE		(0xdeadbeef)
+#define BCM_3368_MEMC_BASE		(0xfff84000)
+#define BCM_3368_DDR_BASE		(0xdeadbeef)
+#define BCM_3368_M2M_BASE		(0xdeadbeef)
+#define BCM_3368_ATM_BASE		(0xdeadbeef)
+#define BCM_3368_XTM_BASE		(0xdeadbeef)
+#define BCM_3368_XTMDMA_BASE		(0xdeadbeef)
+#define BCM_3368_XTMDMAC_BASE		(0xdeadbeef)
+#define BCM_3368_XTMDMAS_BASE		(0xdeadbeef)
+#define BCM_3368_PCM_BASE		(0xfff9c200)
+#define BCM_3368_PCMDMA_BASE		(0xdeadbeef)
+#define BCM_3368_PCMDMAC_BASE		(0xdeadbeef)
+#define BCM_3368_PCMDMAS_BASE		(0xdeadbeef)
+#define BCM_3368_RNG_BASE		(0xdeadbeef)
+#define BCM_3368_MISC_BASE		(0xdeadbeef)
+
+/*
+ * 6328 register sets base address
+ */
+#define BCM_6328_DSL_LMEM_BASE		(0xdeadbeef)
+#define BCM_6328_PERF_BASE		(0xb0000000)
+#define BCM_6328_TIMER_BASE		(0xb0000040)
+#define BCM_6328_WDT_BASE		(0xb000005c)
+#define BCM_6328_UART0_BASE		(0xb0000100)
+#define BCM_6328_UART1_BASE		(0xb0000120)
+#define BCM_6328_GPIO_BASE		(0xb0000080)
+#define BCM_6328_SPI_BASE		(0xdeadbeef)
+#define BCM_6328_HSSPI_BASE		(0xb0001000)
+#define BCM_6328_UDC0_BASE		(0xdeadbeef)
+#define BCM_6328_USBDMA_BASE		(0xb000c000)
+#define BCM_6328_OHCI0_BASE		(0xb0002600)
+#define BCM_6328_OHCI_PRIV_BASE		(0xdeadbeef)
+#define BCM_6328_USBH_PRIV_BASE		(0xb0002700)
+#define BCM_6328_USBD_BASE		(0xb0002400)
+#define BCM_6328_MPI_BASE		(0xdeadbeef)
+#define BCM_6328_PCMCIA_BASE		(0xdeadbeef)
+#define BCM_6328_PCIE_BASE		(0xb0e40000)
+#define BCM_6328_SDRAM_REGS_BASE	(0xdeadbeef)
+#define BCM_6328_DSL_BASE		(0xb0001900)
+#define BCM_6328_UBUS_BASE		(0xdeadbeef)
+#define BCM_6328_ENET0_BASE		(0xdeadbeef)
+#define BCM_6328_ENET1_BASE		(0xdeadbeef)
+#define BCM_6328_ENETDMA_BASE		(0xb000d800)
+#define BCM_6328_ENETDMAC_BASE		(0xb000da00)
+#define BCM_6328_ENETDMAS_BASE		(0xb000dc00)
+#define BCM_6328_ENETSW_BASE		(0xb0e00000)
+#define BCM_6328_EHCI0_BASE		(0xb0002500)
+#define BCM_6328_SDRAM_BASE		(0xdeadbeef)
+#define BCM_6328_MEMC_BASE		(0xdeadbeef)
+#define BCM_6328_DDR_BASE		(0xb0003000)
+#define BCM_6328_M2M_BASE		(0xdeadbeef)
+#define BCM_6328_ATM_BASE		(0xdeadbeef)
+#define BCM_6328_XTM_BASE		(0xdeadbeef)
+#define BCM_6328_XTMDMA_BASE		(0xb000b800)
+#define BCM_6328_XTMDMAC_BASE		(0xdeadbeef)
+#define BCM_6328_XTMDMAS_BASE		(0xdeadbeef)
+#define BCM_6328_PCM_BASE		(0xb000a800)
+#define BCM_6328_PCMDMA_BASE		(0xdeadbeef)
+#define BCM_6328_PCMDMAC_BASE		(0xdeadbeef)
+#define BCM_6328_PCMDMAS_BASE		(0xdeadbeef)
+#define BCM_6328_RNG_BASE		(0xdeadbeef)
+#define BCM_6328_MISC_BASE		(0xb0001800)
+#define BCM_6328_OTP_BASE		(0xb0000600)
+
+/*
+ * 6338 register sets base address
+ */
+#define BCM_6338_DSL_LMEM_BASE		(0xfff00000)
+#define BCM_6338_PERF_BASE		(0xfffe0000)
+#define BCM_6338_BB_BASE		(0xfffe0100)
+#define BCM_6338_TIMER_BASE		(0xfffe0200)
+#define BCM_6338_WDT_BASE		(0xfffe021c)
+#define BCM_6338_UART0_BASE		(0xfffe0300)
+#define BCM_6338_UART1_BASE		(0xdeadbeef)
+#define BCM_6338_GPIO_BASE		(0xfffe0400)
+#define BCM_6338_SPI_BASE		(0xfffe0c00)
+#define BCM_6338_HSSPI_BASE		(0xdeadbeef)
+#define BCM_6338_UDC0_BASE		(0xdeadbeef)
+#define BCM_6338_USBDMA_BASE		(0xfffe2400)
+#define BCM_6338_OHCI0_BASE		(0xdeadbeef)
+#define BCM_6338_OHCI_PRIV_BASE		(0xfffe3000)
+#define BCM_6338_USBH_PRIV_BASE		(0xdeadbeef)
+#define BCM_6338_USBD_BASE		(0xdeadbeef)
+#define BCM_6338_MPI_BASE		(0xfffe3160)
+#define BCM_6338_PCMCIA_BASE		(0xdeadbeef)
+#define BCM_6338_PCIE_BASE		(0xdeadbeef)
+#define BCM_6338_SDRAM_REGS_BASE	(0xfffe3100)
+#define BCM_6338_DSL_BASE		(0xfffe1000)
+#define BCM_6338_UBUS_BASE		(0xdeadbeef)
+#define BCM_6338_ENET0_BASE		(0xfffe2800)
+#define BCM_6338_ENET1_BASE		(0xdeadbeef)
+#define BCM_6338_ENETDMA_BASE		(0xfffe2400)
+#define BCM_6338_ENETDMAC_BASE		(0xfffe2500)
+#define BCM_6338_ENETDMAS_BASE		(0xfffe2600)
+#define BCM_6338_ENETSW_BASE		(0xdeadbeef)
+#define BCM_6338_EHCI0_BASE		(0xdeadbeef)
+#define BCM_6338_SDRAM_BASE		(0xfffe3100)
+#define BCM_6338_MEMC_BASE		(0xdeadbeef)
+#define BCM_6338_DDR_BASE		(0xdeadbeef)
+#define BCM_6338_M2M_BASE		(0xdeadbeef)
+#define BCM_6338_ATM_BASE		(0xfffe2000)
+#define BCM_6338_XTM_BASE		(0xdeadbeef)
+#define BCM_6338_XTMDMA_BASE		(0xdeadbeef)
+#define BCM_6338_XTMDMAC_BASE		(0xdeadbeef)
+#define BCM_6338_XTMDMAS_BASE		(0xdeadbeef)
+#define BCM_6338_PCM_BASE		(0xdeadbeef)
+#define BCM_6338_PCMDMA_BASE		(0xdeadbeef)
+#define BCM_6338_PCMDMAC_BASE		(0xdeadbeef)
+#define BCM_6338_PCMDMAS_BASE		(0xdeadbeef)
+#define BCM_6338_RNG_BASE		(0xdeadbeef)
+#define BCM_6338_MISC_BASE		(0xdeadbeef)
+
+/*
+ * 6345 register sets base address
+ */
+#define BCM_6345_DSL_LMEM_BASE		(0xfff00000)
+#define BCM_6345_PERF_BASE		(0xfffe0000)
+#define BCM_6345_BB_BASE		(0xfffe0100)
+#define BCM_6345_TIMER_BASE		(0xfffe0200)
+#define BCM_6345_WDT_BASE		(0xfffe021c)
+#define BCM_6345_UART0_BASE		(0xfffe0300)
+#define BCM_6345_UART1_BASE		(0xdeadbeef)
+#define BCM_6345_GPIO_BASE		(0xfffe0400)
+#define BCM_6345_SPI_BASE		(0xdeadbeef)
+#define BCM_6345_HSSPI_BASE		(0xdeadbeef)
+#define BCM_6345_UDC0_BASE		(0xdeadbeef)
+#define BCM_6345_USBDMA_BASE		(0xfffe2800)
+#define BCM_6345_ENET0_BASE		(0xfffe1800)
+#define BCM_6345_ENETDMA_BASE		(0xfffe2800)
+#define BCM_6345_ENETDMAC_BASE		(0xfffe2840)
+#define BCM_6345_ENETDMAS_BASE		(0xfffe2a00)
+#define BCM_6345_ENETSW_BASE		(0xdeadbeef)
+#define BCM_6345_PCMCIA_BASE		(0xfffe2028)
+#define BCM_6345_MPI_BASE		(0xfffe2000)
+#define BCM_6345_PCIE_BASE		(0xdeadbeef)
+#define BCM_6345_OHCI0_BASE		(0xfffe2100)
+#define BCM_6345_OHCI_PRIV_BASE		(0xfffe2200)
+#define BCM_6345_USBH_PRIV_BASE		(0xdeadbeef)
+#define BCM_6345_USBD_BASE		(0xdeadbeef)
+#define BCM_6345_SDRAM_REGS_BASE	(0xfffe2300)
+#define BCM_6345_DSL_BASE		(0xdeadbeef)
+#define BCM_6345_UBUS_BASE		(0xdeadbeef)
+#define BCM_6345_ENET1_BASE		(0xdeadbeef)
+#define BCM_6345_EHCI0_BASE		(0xdeadbeef)
+#define BCM_6345_SDRAM_BASE		(0xfffe2300)
+#define BCM_6345_MEMC_BASE		(0xdeadbeef)
+#define BCM_6345_DDR_BASE		(0xdeadbeef)
+#define BCM_6345_M2M_BASE		(0xdeadbeef)
+#define BCM_6345_ATM_BASE		(0xfffe4000)
+#define BCM_6345_XTM_BASE		(0xdeadbeef)
+#define BCM_6345_XTMDMA_BASE		(0xdeadbeef)
+#define BCM_6345_XTMDMAC_BASE		(0xdeadbeef)
+#define BCM_6345_XTMDMAS_BASE		(0xdeadbeef)
+#define BCM_6345_PCM_BASE		(0xdeadbeef)
+#define BCM_6345_PCMDMA_BASE		(0xdeadbeef)
+#define BCM_6345_PCMDMAC_BASE		(0xdeadbeef)
+#define BCM_6345_PCMDMAS_BASE		(0xdeadbeef)
+#define BCM_6345_RNG_BASE		(0xdeadbeef)
+#define BCM_6345_MISC_BASE		(0xdeadbeef)
+
+/*
+ * 6348 register sets base address
+ */
+#define BCM_6348_DSL_LMEM_BASE		(0xfff00000)
+#define BCM_6348_PERF_BASE		(0xfffe0000)
+#define BCM_6348_TIMER_BASE		(0xfffe0200)
+#define BCM_6348_WDT_BASE		(0xfffe021c)
+#define BCM_6348_UART0_BASE		(0xfffe0300)
+#define BCM_6348_UART1_BASE		(0xdeadbeef)
+#define BCM_6348_GPIO_BASE		(0xfffe0400)
+#define BCM_6348_SPI_BASE		(0xfffe0c00)
+#define BCM_6348_HSSPI_BASE		(0xdeadbeef)
+#define BCM_6348_UDC0_BASE		(0xfffe1000)
+#define BCM_6348_USBDMA_BASE		(0xdeadbeef)
+#define BCM_6348_OHCI0_BASE		(0xfffe1b00)
+#define BCM_6348_OHCI_PRIV_BASE		(0xfffe1c00)
+#define BCM_6348_USBH_PRIV_BASE		(0xdeadbeef)
+#define BCM_6348_USBD_BASE		(0xdeadbeef)
+#define BCM_6348_MPI_BASE		(0xfffe2000)
+#define BCM_6348_PCMCIA_BASE		(0xfffe2054)
+#define BCM_6348_PCIE_BASE		(0xdeadbeef)
+#define BCM_6348_SDRAM_REGS_BASE	(0xfffe2300)
+#define BCM_6348_M2M_BASE		(0xfffe2800)
+#define BCM_6348_DSL_BASE		(0xfffe3000)
+#define BCM_6348_ENET0_BASE		(0xfffe6000)
+#define BCM_6348_ENET1_BASE		(0xfffe6800)
+#define BCM_6348_ENETDMA_BASE		(0xfffe7000)
+#define BCM_6348_ENETDMAC_BASE		(0xfffe7100)
+#define BCM_6348_ENETDMAS_BASE		(0xfffe7200)
+#define BCM_6348_ENETSW_BASE		(0xdeadbeef)
+#define BCM_6348_EHCI0_BASE		(0xdeadbeef)
+#define BCM_6348_SDRAM_BASE		(0xfffe2300)
+#define BCM_6348_MEMC_BASE		(0xdeadbeef)
+#define BCM_6348_DDR_BASE		(0xdeadbeef)
+#define BCM_6348_ATM_BASE		(0xfffe4000)
+#define BCM_6348_XTM_BASE		(0xdeadbeef)
+#define BCM_6348_XTMDMA_BASE		(0xdeadbeef)
+#define BCM_6348_XTMDMAC_BASE		(0xdeadbeef)
+#define BCM_6348_XTMDMAS_BASE		(0xdeadbeef)
+#define BCM_6348_PCM_BASE		(0xdeadbeef)
+#define BCM_6348_PCMDMA_BASE		(0xdeadbeef)
+#define BCM_6348_PCMDMAC_BASE		(0xdeadbeef)
+#define BCM_6348_PCMDMAS_BASE		(0xdeadbeef)
+#define BCM_6348_RNG_BASE		(0xdeadbeef)
+#define BCM_6348_MISC_BASE		(0xdeadbeef)
+
+/*
+ * 6358 register sets base address
+ */
+#define BCM_6358_DSL_LMEM_BASE		(0xfff00000)
+#define BCM_6358_PERF_BASE		(0xfffe0000)
+#define BCM_6358_TIMER_BASE		(0xfffe0040)
+#define BCM_6358_WDT_BASE		(0xfffe005c)
+#define BCM_6358_UART0_BASE		(0xfffe0100)
+#define BCM_6358_UART1_BASE		(0xfffe0120)
+#define BCM_6358_GPIO_BASE		(0xfffe0080)
+#define BCM_6358_SPI_BASE		(0xfffe0800)
+#define BCM_6358_HSSPI_BASE		(0xdeadbeef)
+#define BCM_6358_UDC0_BASE		(0xfffe0800)
+#define BCM_6358_USBDMA_BASE		(0xdeadbeef)
+#define BCM_6358_OHCI0_BASE		(0xfffe1400)
+#define BCM_6358_OHCI_PRIV_BASE		(0xdeadbeef)
+#define BCM_6358_USBH_PRIV_BASE		(0xfffe1500)
+#define BCM_6358_USBD_BASE		(0xdeadbeef)
+#define BCM_6358_MPI_BASE		(0xfffe1000)
+#define BCM_6358_PCMCIA_BASE		(0xfffe1054)
+#define BCM_6358_PCIE_BASE		(0xdeadbeef)
+#define BCM_6358_SDRAM_REGS_BASE	(0xfffe2300)
+#define BCM_6358_M2M_BASE		(0xdeadbeef)
+#define BCM_6358_DSL_BASE		(0xfffe3000)
+#define BCM_6358_ENET0_BASE		(0xfffe4000)
+#define BCM_6358_ENET1_BASE		(0xfffe4800)
+#define BCM_6358_ENETDMA_BASE		(0xfffe5000)
+#define BCM_6358_ENETDMAC_BASE		(0xfffe5100)
+#define BCM_6358_ENETDMAS_BASE		(0xfffe5200)
+#define BCM_6358_ENETSW_BASE		(0xdeadbeef)
+#define BCM_6358_EHCI0_BASE		(0xfffe1300)
+#define BCM_6358_SDRAM_BASE		(0xdeadbeef)
+#define BCM_6358_MEMC_BASE		(0xfffe1200)
+#define BCM_6358_DDR_BASE		(0xfffe12a0)
+#define BCM_6358_ATM_BASE		(0xfffe2000)
+#define BCM_6358_XTM_BASE		(0xdeadbeef)
+#define BCM_6358_XTMDMA_BASE		(0xdeadbeef)
+#define BCM_6358_XTMDMAC_BASE		(0xdeadbeef)
+#define BCM_6358_XTMDMAS_BASE		(0xdeadbeef)
+#define BCM_6358_PCM_BASE		(0xfffe1600)
+#define BCM_6358_PCMDMA_BASE		(0xfffe1800)
+#define BCM_6358_PCMDMAC_BASE		(0xfffe1900)
+#define BCM_6358_PCMDMAS_BASE		(0xfffe1a00)
+#define BCM_6358_RNG_BASE		(0xdeadbeef)
+#define BCM_6358_MISC_BASE		(0xdeadbeef)
+
+
+/*
+ * 6362 register sets base address
+ */
+#define BCM_6362_DSL_LMEM_BASE		(0xdeadbeef)
+#define BCM_6362_PERF_BASE		(0xb0000000)
+#define BCM_6362_TIMER_BASE		(0xb0000040)
+#define BCM_6362_WDT_BASE		(0xb000005c)
+#define BCM_6362_UART0_BASE             (0xb0000100)
+#define BCM_6362_UART1_BASE		(0xb0000120)
+#define BCM_6362_GPIO_BASE		(0xb0000080)
+#define BCM_6362_SPI_BASE		(0xb0000800)
+#define BCM_6362_HSSPI_BASE		(0xb0001000)
+#define BCM_6362_UDC0_BASE		(0xdeadbeef)
+#define BCM_6362_USBDMA_BASE		(0xb000c000)
+#define BCM_6362_OHCI0_BASE		(0xb0002600)
+#define BCM_6362_OHCI_PRIV_BASE		(0xdeadbeef)
+#define BCM_6362_USBH_PRIV_BASE		(0xb0002700)
+#define BCM_6362_USBD_BASE		(0xb0002400)
+#define BCM_6362_MPI_BASE		(0xdeadbeef)
+#define BCM_6362_PCMCIA_BASE		(0xdeadbeef)
+#define BCM_6362_PCIE_BASE		(0xb0e40000)
+#define BCM_6362_SDRAM_REGS_BASE	(0xdeadbeef)
+#define BCM_6362_DSL_BASE		(0xdeadbeef)
+#define BCM_6362_UBUS_BASE		(0xdeadbeef)
+#define BCM_6362_ENET0_BASE		(0xdeadbeef)
+#define BCM_6362_ENET1_BASE		(0xdeadbeef)
+#define BCM_6362_ENETDMA_BASE		(0xb000d800)
+#define BCM_6362_ENETDMAC_BASE		(0xb000da00)
+#define BCM_6362_ENETDMAS_BASE		(0xb000dc00)
+#define BCM_6362_ENETSW_BASE		(0xb0e00000)
+#define BCM_6362_EHCI0_BASE		(0xb0002500)
+#define BCM_6362_SDRAM_BASE		(0xdeadbeef)
+#define BCM_6362_MEMC_BASE		(0xdeadbeef)
+#define BCM_6362_DDR_BASE		(0xb0003000)
+#define BCM_6362_M2M_BASE		(0xdeadbeef)
+#define BCM_6362_ATM_BASE		(0xdeadbeef)
+#define BCM_6362_XTM_BASE		(0xb0007800)
+#define BCM_6362_XTMDMA_BASE		(0xb000b800)
+#define BCM_6362_XTMDMAC_BASE		(0xdeadbeef)
+#define BCM_6362_XTMDMAS_BASE		(0xdeadbeef)
+#define BCM_6362_PCM_BASE		(0xb000a800)
+#define BCM_6362_PCMDMA_BASE		(0xdeadbeef)
+#define BCM_6362_PCMDMAC_BASE		(0xdeadbeef)
+#define BCM_6362_PCMDMAS_BASE		(0xdeadbeef)
+#define BCM_6362_RNG_BASE		(0xdeadbeef)
+#define BCM_6362_MISC_BASE		(0xb0001800)
+
+#define BCM_6362_NAND_REG_BASE		(0xb0000200)
+#define BCM_6362_NAND_CACHE_BASE	(0xb0000600)
+#define BCM_6362_LED_BASE		(0xb0001900)
+#define BCM_6362_IPSEC_BASE		(0xb0002800)
+#define BCM_6362_IPSEC_DMA_BASE		(0xb000d000)
+#define BCM_6362_WLAN_CHIPCOMMON_BASE	(0xb0004000)
+#define BCM_6362_WLAN_D11_BASE		(0xb0005000)
+#define BCM_6362_WLAN_SHIM_BASE		(0xb0007000)
+
+/*
+ * 6368 register sets base address
+ */
+#define BCM_6368_DSL_LMEM_BASE		(0xdeadbeef)
+#define BCM_6368_PERF_BASE		(0xb0000000)
+#define BCM_6368_TIMER_BASE		(0xb0000040)
+#define BCM_6368_WDT_BASE		(0xb000005c)
+#define BCM_6368_UART0_BASE		(0xb0000100)
+#define BCM_6368_UART1_BASE		(0xb0000120)
+#define BCM_6368_GPIO_BASE		(0xb0000080)
+#define BCM_6368_SPI_BASE		(0xb0000800)
+#define BCM_6368_HSSPI_BASE		(0xdeadbeef)
+#define BCM_6368_UDC0_BASE		(0xdeadbeef)
+#define BCM_6368_USBDMA_BASE		(0xb0004800)
+#define BCM_6368_OHCI0_BASE		(0xb0001600)
+#define BCM_6368_OHCI_PRIV_BASE		(0xdeadbeef)
+#define BCM_6368_USBH_PRIV_BASE		(0xb0001700)
+#define BCM_6368_USBD_BASE		(0xb0001400)
+#define BCM_6368_MPI_BASE		(0xb0001000)
+#define BCM_6368_PCMCIA_BASE		(0xb0001054)
+#define BCM_6368_PCIE_BASE		(0xdeadbeef)
+#define BCM_6368_SDRAM_REGS_BASE	(0xdeadbeef)
+#define BCM_6368_M2M_BASE		(0xdeadbeef)
+#define BCM_6368_DSL_BASE		(0xdeadbeef)
+#define BCM_6368_ENET0_BASE		(0xdeadbeef)
+#define BCM_6368_ENET1_BASE		(0xdeadbeef)
+#define BCM_6368_ENETDMA_BASE		(0xb0006800)
+#define BCM_6368_ENETDMAC_BASE		(0xb0006a00)
+#define BCM_6368_ENETDMAS_BASE		(0xb0006c00)
+#define BCM_6368_ENETSW_BASE		(0xb0f00000)
+#define BCM_6368_EHCI0_BASE		(0xb0001500)
+#define BCM_6368_SDRAM_BASE		(0xdeadbeef)
+#define BCM_6368_MEMC_BASE		(0xb0001200)
+#define BCM_6368_DDR_BASE		(0xb0001280)
+#define BCM_6368_ATM_BASE		(0xdeadbeef)
+#define BCM_6368_XTM_BASE		(0xb0001800)
+#define BCM_6368_XTMDMA_BASE		(0xb0005000)
+#define BCM_6368_XTMDMAC_BASE		(0xb0005200)
+#define BCM_6368_XTMDMAS_BASE		(0xb0005400)
+#define BCM_6368_PCM_BASE		(0xb0004000)
+#define BCM_6368_PCMDMA_BASE		(0xb0005800)
+#define BCM_6368_PCMDMAC_BASE		(0xb0005a00)
+#define BCM_6368_PCMDMAS_BASE		(0xb0005c00)
+#define BCM_6368_RNG_BASE		(0xb0004180)
+#define BCM_6368_MISC_BASE		(0xdeadbeef)
+
+
+extern const unsigned long *bcm63xx_regs_base;
+
+#define __GEN_CPU_REGS_TABLE(__cpu)					\
+	[RSET_DSL_LMEM]		= BCM_## __cpu ##_DSL_LMEM_BASE,	\
+	[RSET_PERF]		= BCM_## __cpu ##_PERF_BASE,		\
+	[RSET_TIMER]		= BCM_## __cpu ##_TIMER_BASE,		\
+	[RSET_WDT]		= BCM_## __cpu ##_WDT_BASE,		\
+	[RSET_UART0]		= BCM_## __cpu ##_UART0_BASE,		\
+	[RSET_UART1]		= BCM_## __cpu ##_UART1_BASE,		\
+	[RSET_GPIO]		= BCM_## __cpu ##_GPIO_BASE,		\
+	[RSET_SPI]		= BCM_## __cpu ##_SPI_BASE,		\
+	[RSET_HSSPI]		= BCM_## __cpu ##_HSSPI_BASE,		\
+	[RSET_UDC0]		= BCM_## __cpu ##_UDC0_BASE,		\
+	[RSET_OHCI0]		= BCM_## __cpu ##_OHCI0_BASE,		\
+	[RSET_OHCI_PRIV]	= BCM_## __cpu ##_OHCI_PRIV_BASE,	\
+	[RSET_USBH_PRIV]	= BCM_## __cpu ##_USBH_PRIV_BASE,	\
+	[RSET_USBD]		= BCM_## __cpu ##_USBD_BASE,		\
+	[RSET_USBDMA]		= BCM_## __cpu ##_USBDMA_BASE,		\
+	[RSET_MPI]		= BCM_## __cpu ##_MPI_BASE,		\
+	[RSET_PCMCIA]		= BCM_## __cpu ##_PCMCIA_BASE,		\
+	[RSET_PCIE]		= BCM_## __cpu ##_PCIE_BASE,		\
+	[RSET_DSL]		= BCM_## __cpu ##_DSL_BASE,		\
+	[RSET_ENET0]		= BCM_## __cpu ##_ENET0_BASE,		\
+	[RSET_ENET1]		= BCM_## __cpu ##_ENET1_BASE,		\
+	[RSET_ENETDMA]		= BCM_## __cpu ##_ENETDMA_BASE,		\
+	[RSET_ENETDMAC]		= BCM_## __cpu ##_ENETDMAC_BASE,	\
+	[RSET_ENETDMAS]		= BCM_## __cpu ##_ENETDMAS_BASE,	\
+	[RSET_ENETSW]		= BCM_## __cpu ##_ENETSW_BASE,		\
+	[RSET_EHCI0]		= BCM_## __cpu ##_EHCI0_BASE,		\
+	[RSET_SDRAM]		= BCM_## __cpu ##_SDRAM_BASE,		\
+	[RSET_MEMC]		= BCM_## __cpu ##_MEMC_BASE,		\
+	[RSET_DDR]		= BCM_## __cpu ##_DDR_BASE,		\
+	[RSET_M2M]		= BCM_## __cpu ##_M2M_BASE,		\
+	[RSET_ATM]		= BCM_## __cpu ##_ATM_BASE,		\
+	[RSET_XTM]		= BCM_## __cpu ##_XTM_BASE,		\
+	[RSET_XTMDMA]		= BCM_## __cpu ##_XTMDMA_BASE,		\
+	[RSET_XTMDMAC]		= BCM_## __cpu ##_XTMDMAC_BASE,		\
+	[RSET_XTMDMAS]		= BCM_## __cpu ##_XTMDMAS_BASE,		\
+	[RSET_PCM]		= BCM_## __cpu ##_PCM_BASE,		\
+	[RSET_PCMDMA]		= BCM_## __cpu ##_PCMDMA_BASE,		\
+	[RSET_PCMDMAC]		= BCM_## __cpu ##_PCMDMAC_BASE,		\
+	[RSET_PCMDMAS]		= BCM_## __cpu ##_PCMDMAS_BASE,		\
+	[RSET_RNG]		= BCM_## __cpu ##_RNG_BASE,		\
+	[RSET_MISC]		= BCM_## __cpu ##_MISC_BASE,		\
+
+
+static inline unsigned long bcm63xx_regset_address(enum bcm63xx_regs_set set)
+{
+	return bcm63xx_regs_base[set];
+}
+
+/*
+ * IRQ number changes across CPU too
+ */
+enum bcm63xx_irq {
+	IRQ_TIMER = 0,
+	IRQ_SPI,
+	IRQ_UART0,
+	IRQ_UART1,
+	IRQ_DSL,
+	IRQ_ENET0,
+	IRQ_ENET1,
+	IRQ_ENET_PHY,
+	IRQ_HSSPI,
+	IRQ_OHCI0,
+	IRQ_EHCI0,
+	IRQ_USBD,
+	IRQ_USBD_RXDMA0,
+	IRQ_USBD_TXDMA0,
+	IRQ_USBD_RXDMA1,
+	IRQ_USBD_TXDMA1,
+	IRQ_USBD_RXDMA2,
+	IRQ_USBD_TXDMA2,
+	IRQ_ENET0_RXDMA,
+	IRQ_ENET0_TXDMA,
+	IRQ_ENET1_RXDMA,
+	IRQ_ENET1_TXDMA,
+	IRQ_PCI,
+	IRQ_PCMCIA,
+	IRQ_ATM,
+	IRQ_ENETSW_RXDMA0,
+	IRQ_ENETSW_RXDMA1,
+	IRQ_ENETSW_RXDMA2,
+	IRQ_ENETSW_RXDMA3,
+	IRQ_ENETSW_TXDMA0,
+	IRQ_ENETSW_TXDMA1,
+	IRQ_ENETSW_TXDMA2,
+	IRQ_ENETSW_TXDMA3,
+	IRQ_XTM,
+	IRQ_XTM_DMA0,
+};
+
+/*
+ * 3368 irqs
+ */
+#define BCM_3368_TIMER_IRQ		(IRQ_INTERNAL_BASE + 0)
+#define BCM_3368_SPI_IRQ		(IRQ_INTERNAL_BASE + 1)
+#define BCM_3368_UART0_IRQ		(IRQ_INTERNAL_BASE + 2)
+#define BCM_3368_UART1_IRQ		(IRQ_INTERNAL_BASE + 3)
+#define BCM_3368_DSL_IRQ		0
+#define BCM_3368_UDC0_IRQ		0
+#define BCM_3368_OHCI0_IRQ		0
+#define BCM_3368_ENET0_IRQ		(IRQ_INTERNAL_BASE + 8)
+#define BCM_3368_ENET1_IRQ		(IRQ_INTERNAL_BASE + 6)
+#define BCM_3368_ENET_PHY_IRQ		(IRQ_INTERNAL_BASE + 9)
+#define BCM_3368_ENET0_RXDMA_IRQ	(IRQ_INTERNAL_BASE + 15)
+#define BCM_3368_ENET0_TXDMA_IRQ	(IRQ_INTERNAL_BASE + 16)
+#define BCM_3368_HSSPI_IRQ		0
+#define BCM_3368_EHCI0_IRQ		0
+#define BCM_3368_USBD_IRQ		0
+#define BCM_3368_USBD_RXDMA0_IRQ	0
+#define BCM_3368_USBD_TXDMA0_IRQ	0
+#define BCM_3368_USBD_RXDMA1_IRQ	0
+#define BCM_3368_USBD_TXDMA1_IRQ	0
+#define BCM_3368_USBD_RXDMA2_IRQ	0
+#define BCM_3368_USBD_TXDMA2_IRQ	0
+#define BCM_3368_ENET1_RXDMA_IRQ        (IRQ_INTERNAL_BASE + 17)
+#define BCM_3368_ENET1_TXDMA_IRQ        (IRQ_INTERNAL_BASE + 18)
+#define BCM_3368_PCI_IRQ		(IRQ_INTERNAL_BASE + 31)
+#define BCM_3368_PCMCIA_IRQ		0
+#define BCM_3368_ATM_IRQ		0
+#define BCM_3368_ENETSW_RXDMA0_IRQ	0
+#define BCM_3368_ENETSW_RXDMA1_IRQ	0
+#define BCM_3368_ENETSW_RXDMA2_IRQ	0
+#define BCM_3368_ENETSW_RXDMA3_IRQ	0
+#define BCM_3368_ENETSW_TXDMA0_IRQ	0
+#define BCM_3368_ENETSW_TXDMA1_IRQ	0
+#define BCM_3368_ENETSW_TXDMA2_IRQ	0
+#define BCM_3368_ENETSW_TXDMA3_IRQ	0
+#define BCM_3368_XTM_IRQ		0
+#define BCM_3368_XTM_DMA0_IRQ		0
+
+#define BCM_3368_EXT_IRQ0		(IRQ_INTERNAL_BASE + 25)
+#define BCM_3368_EXT_IRQ1		(IRQ_INTERNAL_BASE + 26)
+#define BCM_3368_EXT_IRQ2		(IRQ_INTERNAL_BASE + 27)
+#define BCM_3368_EXT_IRQ3		(IRQ_INTERNAL_BASE + 28)
+
+
+/*
+ * 6328 irqs
+ */
+#define BCM_6328_HIGH_IRQ_BASE		(IRQ_INTERNAL_BASE + 32)
+
+#define BCM_6328_TIMER_IRQ		(IRQ_INTERNAL_BASE + 31)
+#define BCM_6328_SPI_IRQ		0
+#define BCM_6328_UART0_IRQ		(IRQ_INTERNAL_BASE + 28)
+#define BCM_6328_UART1_IRQ		(BCM_6328_HIGH_IRQ_BASE + 7)
+#define BCM_6328_DSL_IRQ		(IRQ_INTERNAL_BASE + 4)
+#define BCM_6328_UDC0_IRQ		0
+#define BCM_6328_ENET0_IRQ		0
+#define BCM_6328_ENET1_IRQ		0
+#define BCM_6328_ENET_PHY_IRQ		(IRQ_INTERNAL_BASE + 12)
+#define BCM_6328_HSSPI_IRQ		(IRQ_INTERNAL_BASE + 29)
+#define BCM_6328_OHCI0_IRQ		(BCM_6328_HIGH_IRQ_BASE + 9)
+#define BCM_6328_EHCI0_IRQ		(BCM_6328_HIGH_IRQ_BASE + 10)
+#define BCM_6328_USBD_IRQ		(IRQ_INTERNAL_BASE + 4)
+#define BCM_6328_USBD_RXDMA0_IRQ	(IRQ_INTERNAL_BASE + 5)
+#define BCM_6328_USBD_TXDMA0_IRQ	(IRQ_INTERNAL_BASE + 6)
+#define BCM_6328_USBD_RXDMA1_IRQ	(IRQ_INTERNAL_BASE + 7)
+#define BCM_6328_USBD_TXDMA1_IRQ	(IRQ_INTERNAL_BASE + 8)
+#define BCM_6328_USBD_RXDMA2_IRQ	(IRQ_INTERNAL_BASE + 9)
+#define BCM_6328_USBD_TXDMA2_IRQ	(IRQ_INTERNAL_BASE + 10)
+#define BCM_6328_PCMCIA_IRQ		0
+#define BCM_6328_ENET0_RXDMA_IRQ	0
+#define BCM_6328_ENET0_TXDMA_IRQ	0
+#define BCM_6328_ENET1_RXDMA_IRQ	0
+#define BCM_6328_ENET1_TXDMA_IRQ	0
+#define BCM_6328_PCI_IRQ		(IRQ_INTERNAL_BASE + 23)
+#define BCM_6328_ATM_IRQ		0
+#define BCM_6328_ENETSW_RXDMA0_IRQ	(BCM_6328_HIGH_IRQ_BASE + 0)
+#define BCM_6328_ENETSW_RXDMA1_IRQ	(BCM_6328_HIGH_IRQ_BASE + 1)
+#define BCM_6328_ENETSW_RXDMA2_IRQ	(BCM_6328_HIGH_IRQ_BASE + 2)
+#define BCM_6328_ENETSW_RXDMA3_IRQ	(BCM_6328_HIGH_IRQ_BASE + 3)
+#define BCM_6328_ENETSW_TXDMA0_IRQ	0
+#define BCM_6328_ENETSW_TXDMA1_IRQ	0
+#define BCM_6328_ENETSW_TXDMA2_IRQ	0
+#define BCM_6328_ENETSW_TXDMA3_IRQ	0
+#define BCM_6328_XTM_IRQ		(BCM_6328_HIGH_IRQ_BASE + 31)
+#define BCM_6328_XTM_DMA0_IRQ		(BCM_6328_HIGH_IRQ_BASE + 11)
+
+#define BCM_6328_PCM_DMA0_IRQ		(IRQ_INTERNAL_BASE + 2)
+#define BCM_6328_PCM_DMA1_IRQ		(IRQ_INTERNAL_BASE + 3)
+#define BCM_6328_EXT_IRQ0		(IRQ_INTERNAL_BASE + 24)
+#define BCM_6328_EXT_IRQ1		(IRQ_INTERNAL_BASE + 25)
+#define BCM_6328_EXT_IRQ2		(IRQ_INTERNAL_BASE + 26)
+#define BCM_6328_EXT_IRQ3		(IRQ_INTERNAL_BASE + 27)
+
+/*
+ * 6338 irqs
+ */
+#define BCM_6338_TIMER_IRQ		(IRQ_INTERNAL_BASE + 0)
+#define BCM_6338_SPI_IRQ		(IRQ_INTERNAL_BASE + 1)
+#define BCM_6338_UART0_IRQ		(IRQ_INTERNAL_BASE + 2)
+#define BCM_6338_UART1_IRQ		0
+#define BCM_6338_DSL_IRQ		(IRQ_INTERNAL_BASE + 5)
+#define BCM_6338_ENET0_IRQ		(IRQ_INTERNAL_BASE + 8)
+#define BCM_6338_ENET1_IRQ		0
+#define BCM_6338_ENET_PHY_IRQ		(IRQ_INTERNAL_BASE + 9)
+#define BCM_6338_HSSPI_IRQ		0
+#define BCM_6338_OHCI0_IRQ		0
+#define BCM_6338_EHCI0_IRQ		0
+#define BCM_6338_USBD_IRQ		0
+#define BCM_6338_USBD_RXDMA0_IRQ	0
+#define BCM_6338_USBD_TXDMA0_IRQ	0
+#define BCM_6338_USBD_RXDMA1_IRQ	0
+#define BCM_6338_USBD_TXDMA1_IRQ	0
+#define BCM_6338_USBD_RXDMA2_IRQ	0
+#define BCM_6338_USBD_TXDMA2_IRQ	0
+#define BCM_6338_ENET0_RXDMA_IRQ	(IRQ_INTERNAL_BASE + 15)
+#define BCM_6338_ENET0_TXDMA_IRQ	(IRQ_INTERNAL_BASE + 16)
+#define BCM_6338_ENET1_RXDMA_IRQ	0
+#define BCM_6338_ENET1_TXDMA_IRQ	0
+#define BCM_6338_PCI_IRQ		0
+#define BCM_6338_PCMCIA_IRQ		0
+#define BCM_6338_ATM_IRQ		0
+#define BCM_6338_ENETSW_RXDMA0_IRQ	0
+#define BCM_6338_ENETSW_RXDMA1_IRQ	0
+#define BCM_6338_ENETSW_RXDMA2_IRQ	0
+#define BCM_6338_ENETSW_RXDMA3_IRQ	0
+#define BCM_6338_ENETSW_TXDMA0_IRQ	0
+#define BCM_6338_ENETSW_TXDMA1_IRQ	0
+#define BCM_6338_ENETSW_TXDMA2_IRQ	0
+#define BCM_6338_ENETSW_TXDMA3_IRQ	0
+#define BCM_6338_XTM_IRQ		0
+#define BCM_6338_XTM_DMA0_IRQ		0
+
+/*
+ * 6345 irqs
+ */
+#define BCM_6345_TIMER_IRQ		(IRQ_INTERNAL_BASE + 0)
+#define BCM_6345_SPI_IRQ		0
+#define BCM_6345_UART0_IRQ		(IRQ_INTERNAL_BASE + 2)
+#define BCM_6345_UART1_IRQ		0
+#define BCM_6345_DSL_IRQ		(IRQ_INTERNAL_BASE + 3)
+#define BCM_6345_ENET0_IRQ		(IRQ_INTERNAL_BASE + 8)
+#define BCM_6345_ENET1_IRQ		0
+#define BCM_6345_ENET_PHY_IRQ		(IRQ_INTERNAL_BASE + 12)
+#define BCM_6345_HSSPI_IRQ		0
+#define BCM_6345_OHCI0_IRQ		0
+#define BCM_6345_EHCI0_IRQ		0
+#define BCM_6345_USBD_IRQ		0
+#define BCM_6345_USBD_RXDMA0_IRQ	0
+#define BCM_6345_USBD_TXDMA0_IRQ	0
+#define BCM_6345_USBD_RXDMA1_IRQ	0
+#define BCM_6345_USBD_TXDMA1_IRQ	0
+#define BCM_6345_USBD_RXDMA2_IRQ	0
+#define BCM_6345_USBD_TXDMA2_IRQ	0
+#define BCM_6345_ENET0_RXDMA_IRQ	(IRQ_INTERNAL_BASE + 13 + 1)
+#define BCM_6345_ENET0_TXDMA_IRQ	(IRQ_INTERNAL_BASE + 13 + 2)
+#define BCM_6345_ENET1_RXDMA_IRQ	0
+#define BCM_6345_ENET1_TXDMA_IRQ	0
+#define BCM_6345_PCI_IRQ		0
+#define BCM_6345_PCMCIA_IRQ		0
+#define BCM_6345_ATM_IRQ		0
+#define BCM_6345_ENETSW_RXDMA0_IRQ	0
+#define BCM_6345_ENETSW_RXDMA1_IRQ	0
+#define BCM_6345_ENETSW_RXDMA2_IRQ	0
+#define BCM_6345_ENETSW_RXDMA3_IRQ	0
+#define BCM_6345_ENETSW_TXDMA0_IRQ	0
+#define BCM_6345_ENETSW_TXDMA1_IRQ	0
+#define BCM_6345_ENETSW_TXDMA2_IRQ	0
+#define BCM_6345_ENETSW_TXDMA3_IRQ	0
+#define BCM_6345_XTM_IRQ		0
+#define BCM_6345_XTM_DMA0_IRQ		0
+
+/*
+ * 6348 irqs
+ */
+#define BCM_6348_TIMER_IRQ		(IRQ_INTERNAL_BASE + 0)
+#define BCM_6348_SPI_IRQ		(IRQ_INTERNAL_BASE + 1)
+#define BCM_6348_UART0_IRQ		(IRQ_INTERNAL_BASE + 2)
+#define BCM_6348_UART1_IRQ		0
+#define BCM_6348_DSL_IRQ		(IRQ_INTERNAL_BASE + 4)
+#define BCM_6348_ENET0_IRQ		(IRQ_INTERNAL_BASE + 8)
+#define BCM_6348_ENET1_IRQ		(IRQ_INTERNAL_BASE + 7)
+#define BCM_6348_ENET_PHY_IRQ		(IRQ_INTERNAL_BASE + 9)
+#define BCM_6348_HSSPI_IRQ		0
+#define BCM_6348_OHCI0_IRQ		(IRQ_INTERNAL_BASE + 12)
+#define BCM_6348_EHCI0_IRQ		0
+#define BCM_6348_USBD_IRQ		0
+#define BCM_6348_USBD_RXDMA0_IRQ	0
+#define BCM_6348_USBD_TXDMA0_IRQ	0
+#define BCM_6348_USBD_RXDMA1_IRQ	0
+#define BCM_6348_USBD_TXDMA1_IRQ	0
+#define BCM_6348_USBD_RXDMA2_IRQ	0
+#define BCM_6348_USBD_TXDMA2_IRQ	0
+#define BCM_6348_ENET0_RXDMA_IRQ	(IRQ_INTERNAL_BASE + 20)
+#define BCM_6348_ENET0_TXDMA_IRQ	(IRQ_INTERNAL_BASE + 21)
+#define BCM_6348_ENET1_RXDMA_IRQ	(IRQ_INTERNAL_BASE + 22)
+#define BCM_6348_ENET1_TXDMA_IRQ	(IRQ_INTERNAL_BASE + 23)
+#define BCM_6348_PCI_IRQ		(IRQ_INTERNAL_BASE + 24)
+#define BCM_6348_PCMCIA_IRQ		(IRQ_INTERNAL_BASE + 24)
+#define BCM_6348_ATM_IRQ		(IRQ_INTERNAL_BASE + 5)
+#define BCM_6348_ENETSW_RXDMA0_IRQ	0
+#define BCM_6348_ENETSW_RXDMA1_IRQ	0
+#define BCM_6348_ENETSW_RXDMA2_IRQ	0
+#define BCM_6348_ENETSW_RXDMA3_IRQ	0
+#define BCM_6348_ENETSW_TXDMA0_IRQ	0
+#define BCM_6348_ENETSW_TXDMA1_IRQ	0
+#define BCM_6348_ENETSW_TXDMA2_IRQ	0
+#define BCM_6348_ENETSW_TXDMA3_IRQ	0
+#define BCM_6348_XTM_IRQ		0
+#define BCM_6348_XTM_DMA0_IRQ		0
+
+/*
+ * 6358 irqs
+ */
+#define BCM_6358_TIMER_IRQ		(IRQ_INTERNAL_BASE + 0)
+#define BCM_6358_SPI_IRQ		(IRQ_INTERNAL_BASE + 1)
+#define BCM_6358_UART0_IRQ		(IRQ_INTERNAL_BASE + 2)
+#define BCM_6358_UART1_IRQ		(IRQ_INTERNAL_BASE + 3)
+#define BCM_6358_DSL_IRQ		(IRQ_INTERNAL_BASE + 29)
+#define BCM_6358_ENET0_IRQ		(IRQ_INTERNAL_BASE + 8)
+#define BCM_6358_ENET1_IRQ		(IRQ_INTERNAL_BASE + 6)
+#define BCM_6358_ENET_PHY_IRQ		(IRQ_INTERNAL_BASE + 9)
+#define BCM_6358_HSSPI_IRQ		0
+#define BCM_6358_OHCI0_IRQ		(IRQ_INTERNAL_BASE + 5)
+#define BCM_6358_EHCI0_IRQ		(IRQ_INTERNAL_BASE + 10)
+#define BCM_6358_USBD_IRQ		0
+#define BCM_6358_USBD_RXDMA0_IRQ	0
+#define BCM_6358_USBD_TXDMA0_IRQ	0
+#define BCM_6358_USBD_RXDMA1_IRQ	0
+#define BCM_6358_USBD_TXDMA1_IRQ	0
+#define BCM_6358_USBD_RXDMA2_IRQ	0
+#define BCM_6358_USBD_TXDMA2_IRQ	0
+#define BCM_6358_ENET0_RXDMA_IRQ	(IRQ_INTERNAL_BASE + 15)
+#define BCM_6358_ENET0_TXDMA_IRQ	(IRQ_INTERNAL_BASE + 16)
+#define BCM_6358_ENET1_RXDMA_IRQ	(IRQ_INTERNAL_BASE + 17)
+#define BCM_6358_ENET1_TXDMA_IRQ	(IRQ_INTERNAL_BASE + 18)
+#define BCM_6358_PCI_IRQ		(IRQ_INTERNAL_BASE + 31)
+#define BCM_6358_PCMCIA_IRQ		(IRQ_INTERNAL_BASE + 24)
+#define BCM_6358_ATM_IRQ		(IRQ_INTERNAL_BASE + 19)
+#define BCM_6358_ENETSW_RXDMA0_IRQ	0
+#define BCM_6358_ENETSW_RXDMA1_IRQ	0
+#define BCM_6358_ENETSW_RXDMA2_IRQ	0
+#define BCM_6358_ENETSW_RXDMA3_IRQ	0
+#define BCM_6358_ENETSW_TXDMA0_IRQ	0
+#define BCM_6358_ENETSW_TXDMA1_IRQ	0
+#define BCM_6358_ENETSW_TXDMA2_IRQ	0
+#define BCM_6358_ENETSW_TXDMA3_IRQ	0
+#define BCM_6358_XTM_IRQ		0
+#define BCM_6358_XTM_DMA0_IRQ		0
+
+#define BCM_6358_PCM_DMA0_IRQ		(IRQ_INTERNAL_BASE + 23)
+#define BCM_6358_PCM_DMA1_IRQ		(IRQ_INTERNAL_BASE + 24)
+#define BCM_6358_EXT_IRQ0		(IRQ_INTERNAL_BASE + 25)
+#define BCM_6358_EXT_IRQ1		(IRQ_INTERNAL_BASE + 26)
+#define BCM_6358_EXT_IRQ2		(IRQ_INTERNAL_BASE + 27)
+#define BCM_6358_EXT_IRQ3		(IRQ_INTERNAL_BASE + 28)
+
+/*
+ * 6362 irqs
+ */
+#define BCM_6362_HIGH_IRQ_BASE		(IRQ_INTERNAL_BASE + 32)
+
+#define BCM_6362_TIMER_IRQ		(IRQ_INTERNAL_BASE + 0)
+#define BCM_6362_SPI_IRQ		(IRQ_INTERNAL_BASE + 2)
+#define BCM_6362_UART0_IRQ		(IRQ_INTERNAL_BASE + 3)
+#define BCM_6362_UART1_IRQ		(IRQ_INTERNAL_BASE + 4)
+#define BCM_6362_DSL_IRQ		(IRQ_INTERNAL_BASE + 28)
+#define BCM_6362_UDC0_IRQ		0
+#define BCM_6362_ENET0_IRQ		0
+#define BCM_6362_ENET1_IRQ		0
+#define BCM_6362_ENET_PHY_IRQ		(IRQ_INTERNAL_BASE + 14)
+#define BCM_6362_HSSPI_IRQ		(IRQ_INTERNAL_BASE + 5)
+#define BCM_6362_OHCI0_IRQ		(IRQ_INTERNAL_BASE + 9)
+#define BCM_6362_EHCI0_IRQ		(IRQ_INTERNAL_BASE + 10)
+#define BCM_6362_USBD_IRQ		(IRQ_INTERNAL_BASE + 11)
+#define BCM_6362_USBD_RXDMA0_IRQ	(IRQ_INTERNAL_BASE + 20)
+#define BCM_6362_USBD_TXDMA0_IRQ	(IRQ_INTERNAL_BASE + 21)
+#define BCM_6362_USBD_RXDMA1_IRQ	(IRQ_INTERNAL_BASE + 22)
+#define BCM_6362_USBD_TXDMA1_IRQ	(IRQ_INTERNAL_BASE + 23)
+#define BCM_6362_USBD_RXDMA2_IRQ	(IRQ_INTERNAL_BASE + 24)
+#define BCM_6362_USBD_TXDMA2_IRQ	(IRQ_INTERNAL_BASE + 25)
+#define BCM_6362_PCMCIA_IRQ		0
+#define BCM_6362_ENET0_RXDMA_IRQ	0
+#define BCM_6362_ENET0_TXDMA_IRQ	0
+#define BCM_6362_ENET1_RXDMA_IRQ	0
+#define BCM_6362_ENET1_TXDMA_IRQ	0
+#define BCM_6362_PCI_IRQ		(IRQ_INTERNAL_BASE + 30)
+#define BCM_6362_ATM_IRQ		0
+#define BCM_6362_ENETSW_RXDMA0_IRQ	(BCM_6362_HIGH_IRQ_BASE + 0)
+#define BCM_6362_ENETSW_RXDMA1_IRQ	(BCM_6362_HIGH_IRQ_BASE + 1)
+#define BCM_6362_ENETSW_RXDMA2_IRQ	(BCM_6362_HIGH_IRQ_BASE + 2)
+#define BCM_6362_ENETSW_RXDMA3_IRQ	(BCM_6362_HIGH_IRQ_BASE + 3)
+#define BCM_6362_ENETSW_TXDMA0_IRQ	0
+#define BCM_6362_ENETSW_TXDMA1_IRQ	0
+#define BCM_6362_ENETSW_TXDMA2_IRQ	0
+#define BCM_6362_ENETSW_TXDMA3_IRQ	0
+#define BCM_6362_XTM_IRQ		0
+#define BCM_6362_XTM_DMA0_IRQ		(BCM_6362_HIGH_IRQ_BASE + 12)
+
+#define BCM_6362_RING_OSC_IRQ		(IRQ_INTERNAL_BASE + 1)
+#define BCM_6362_WLAN_GPIO_IRQ		(IRQ_INTERNAL_BASE + 6)
+#define BCM_6362_WLAN_IRQ		(IRQ_INTERNAL_BASE + 7)
+#define BCM_6362_IPSEC_IRQ		(IRQ_INTERNAL_BASE + 8)
+#define BCM_6362_NAND_IRQ		(IRQ_INTERNAL_BASE + 12)
+#define BCM_6362_PCM_IRQ		(IRQ_INTERNAL_BASE + 13)
+#define BCM_6362_DG_IRQ			(IRQ_INTERNAL_BASE + 15)
+#define BCM_6362_EPHY_ENERGY0_IRQ	(IRQ_INTERNAL_BASE + 16)
+#define BCM_6362_EPHY_ENERGY1_IRQ	(IRQ_INTERNAL_BASE + 17)
+#define BCM_6362_EPHY_ENERGY2_IRQ	(IRQ_INTERNAL_BASE + 18)
+#define BCM_6362_EPHY_ENERGY3_IRQ	(IRQ_INTERNAL_BASE + 19)
+#define BCM_6362_IPSEC_DMA0_IRQ		(IRQ_INTERNAL_BASE + 26)
+#define BCM_6362_IPSEC_DMA1_IRQ		(IRQ_INTERNAL_BASE + 27)
+#define BCM_6362_FAP0_IRQ		(IRQ_INTERNAL_BASE + 29)
+#define BCM_6362_PCM_DMA0_IRQ		(BCM_6362_HIGH_IRQ_BASE + 4)
+#define BCM_6362_PCM_DMA1_IRQ		(BCM_6362_HIGH_IRQ_BASE + 5)
+#define BCM_6362_DECT0_IRQ		(BCM_6362_HIGH_IRQ_BASE + 6)
+#define BCM_6362_DECT1_IRQ		(BCM_6362_HIGH_IRQ_BASE + 7)
+#define BCM_6362_EXT_IRQ0		(BCM_6362_HIGH_IRQ_BASE + 8)
+#define BCM_6362_EXT_IRQ1		(BCM_6362_HIGH_IRQ_BASE + 9)
+#define BCM_6362_EXT_IRQ2		(BCM_6362_HIGH_IRQ_BASE + 10)
+#define BCM_6362_EXT_IRQ3		(BCM_6362_HIGH_IRQ_BASE + 11)
+
+/*
+ * 6368 irqs
+ */
+#define BCM_6368_HIGH_IRQ_BASE		(IRQ_INTERNAL_BASE + 32)
+
+#define BCM_6368_TIMER_IRQ		(IRQ_INTERNAL_BASE + 0)
+#define BCM_6368_SPI_IRQ		(IRQ_INTERNAL_BASE + 1)
+#define BCM_6368_UART0_IRQ		(IRQ_INTERNAL_BASE + 2)
+#define BCM_6368_UART1_IRQ		(IRQ_INTERNAL_BASE + 3)
+#define BCM_6368_DSL_IRQ		(IRQ_INTERNAL_BASE + 4)
+#define BCM_6368_ENET0_IRQ		0
+#define BCM_6368_ENET1_IRQ		0
+#define BCM_6368_ENET_PHY_IRQ		(IRQ_INTERNAL_BASE + 15)
+#define BCM_6368_HSSPI_IRQ		0
+#define BCM_6368_OHCI0_IRQ		(IRQ_INTERNAL_BASE + 5)
+#define BCM_6368_EHCI0_IRQ		(IRQ_INTERNAL_BASE + 7)
+#define BCM_6368_USBD_IRQ		(IRQ_INTERNAL_BASE + 8)
+#define BCM_6368_USBD_RXDMA0_IRQ	(IRQ_INTERNAL_BASE + 26)
+#define BCM_6368_USBD_TXDMA0_IRQ	(IRQ_INTERNAL_BASE + 27)
+#define BCM_6368_USBD_RXDMA1_IRQ	(IRQ_INTERNAL_BASE + 28)
+#define BCM_6368_USBD_TXDMA1_IRQ	(IRQ_INTERNAL_BASE + 29)
+#define BCM_6368_USBD_RXDMA2_IRQ	(IRQ_INTERNAL_BASE + 30)
+#define BCM_6368_USBD_TXDMA2_IRQ	(IRQ_INTERNAL_BASE + 31)
+#define BCM_6368_PCMCIA_IRQ		0
+#define BCM_6368_ENET0_RXDMA_IRQ	0
+#define BCM_6368_ENET0_TXDMA_IRQ	0
+#define BCM_6368_ENET1_RXDMA_IRQ	0
+#define BCM_6368_ENET1_TXDMA_IRQ	0
+#define BCM_6368_PCI_IRQ		(IRQ_INTERNAL_BASE + 13)
+#define BCM_6368_ATM_IRQ		0
+#define BCM_6368_ENETSW_RXDMA0_IRQ	(BCM_6368_HIGH_IRQ_BASE + 0)
+#define BCM_6368_ENETSW_RXDMA1_IRQ	(BCM_6368_HIGH_IRQ_BASE + 1)
+#define BCM_6368_ENETSW_RXDMA2_IRQ	(BCM_6368_HIGH_IRQ_BASE + 2)
+#define BCM_6368_ENETSW_RXDMA3_IRQ	(BCM_6368_HIGH_IRQ_BASE + 3)
+#define BCM_6368_ENETSW_TXDMA0_IRQ	(BCM_6368_HIGH_IRQ_BASE + 4)
+#define BCM_6368_ENETSW_TXDMA1_IRQ	(BCM_6368_HIGH_IRQ_BASE + 5)
+#define BCM_6368_ENETSW_TXDMA2_IRQ	(BCM_6368_HIGH_IRQ_BASE + 6)
+#define BCM_6368_ENETSW_TXDMA3_IRQ	(BCM_6368_HIGH_IRQ_BASE + 7)
+#define BCM_6368_XTM_IRQ		(IRQ_INTERNAL_BASE + 11)
+#define BCM_6368_XTM_DMA0_IRQ		(BCM_6368_HIGH_IRQ_BASE + 8)
+
+#define BCM_6368_PCM_DMA0_IRQ		(BCM_6368_HIGH_IRQ_BASE + 30)
+#define BCM_6368_PCM_DMA1_IRQ		(BCM_6368_HIGH_IRQ_BASE + 31)
+#define BCM_6368_EXT_IRQ0		(IRQ_INTERNAL_BASE + 20)
+#define BCM_6368_EXT_IRQ1		(IRQ_INTERNAL_BASE + 21)
+#define BCM_6368_EXT_IRQ2		(IRQ_INTERNAL_BASE + 22)
+#define BCM_6368_EXT_IRQ3		(IRQ_INTERNAL_BASE + 23)
+#define BCM_6368_EXT_IRQ4		(IRQ_INTERNAL_BASE + 24)
+#define BCM_6368_EXT_IRQ5		(IRQ_INTERNAL_BASE + 25)
+
+extern const int *bcm63xx_irqs;
+
+#define __GEN_CPU_IRQ_TABLE(__cpu)					\
+	[IRQ_TIMER]		= BCM_## __cpu ##_TIMER_IRQ,		\
+	[IRQ_SPI]		= BCM_## __cpu ##_SPI_IRQ,		\
+	[IRQ_UART0]		= BCM_## __cpu ##_UART0_IRQ,		\
+	[IRQ_UART1]		= BCM_## __cpu ##_UART1_IRQ,		\
+	[IRQ_DSL]		= BCM_## __cpu ##_DSL_IRQ,		\
+	[IRQ_ENET0]		= BCM_## __cpu ##_ENET0_IRQ,		\
+	[IRQ_ENET1]		= BCM_## __cpu ##_ENET1_IRQ,		\
+	[IRQ_ENET_PHY]		= BCM_## __cpu ##_ENET_PHY_IRQ,		\
+	[IRQ_HSSPI]		= BCM_## __cpu ##_HSSPI_IRQ,		\
+	[IRQ_OHCI0]		= BCM_## __cpu ##_OHCI0_IRQ,		\
+	[IRQ_EHCI0]		= BCM_## __cpu ##_EHCI0_IRQ,		\
+	[IRQ_USBD]		= BCM_## __cpu ##_USBD_IRQ,		\
+	[IRQ_USBD_RXDMA0]	= BCM_## __cpu ##_USBD_RXDMA0_IRQ,	\
+	[IRQ_USBD_TXDMA0]	= BCM_## __cpu ##_USBD_TXDMA0_IRQ,	\
+	[IRQ_USBD_RXDMA1]	= BCM_## __cpu ##_USBD_RXDMA1_IRQ,	\
+	[IRQ_USBD_TXDMA1]	= BCM_## __cpu ##_USBD_TXDMA1_IRQ,	\
+	[IRQ_USBD_RXDMA2]	= BCM_## __cpu ##_USBD_RXDMA2_IRQ,	\
+	[IRQ_USBD_TXDMA2]	= BCM_## __cpu ##_USBD_TXDMA2_IRQ,	\
+	[IRQ_ENET0_RXDMA]	= BCM_## __cpu ##_ENET0_RXDMA_IRQ,	\
+	[IRQ_ENET0_TXDMA]	= BCM_## __cpu ##_ENET0_TXDMA_IRQ,	\
+	[IRQ_ENET1_RXDMA]	= BCM_## __cpu ##_ENET1_RXDMA_IRQ,	\
+	[IRQ_ENET1_TXDMA]	= BCM_## __cpu ##_ENET1_TXDMA_IRQ,	\
+	[IRQ_PCI]		= BCM_## __cpu ##_PCI_IRQ,		\
+	[IRQ_PCMCIA]		= BCM_## __cpu ##_PCMCIA_IRQ,		\
+	[IRQ_ATM]		= BCM_## __cpu ##_ATM_IRQ,		\
+	[IRQ_ENETSW_RXDMA0]	= BCM_## __cpu ##_ENETSW_RXDMA0_IRQ,	\
+	[IRQ_ENETSW_RXDMA1]	= BCM_## __cpu ##_ENETSW_RXDMA1_IRQ,	\
+	[IRQ_ENETSW_RXDMA2]	= BCM_## __cpu ##_ENETSW_RXDMA2_IRQ,	\
+	[IRQ_ENETSW_RXDMA3]	= BCM_## __cpu ##_ENETSW_RXDMA3_IRQ,	\
+	[IRQ_ENETSW_TXDMA0]	= BCM_## __cpu ##_ENETSW_TXDMA0_IRQ,	\
+	[IRQ_ENETSW_TXDMA1]	= BCM_## __cpu ##_ENETSW_TXDMA1_IRQ,	\
+	[IRQ_ENETSW_TXDMA2]	= BCM_## __cpu ##_ENETSW_TXDMA2_IRQ,	\
+	[IRQ_ENETSW_TXDMA3]	= BCM_## __cpu ##_ENETSW_TXDMA3_IRQ,	\
+	[IRQ_XTM]		= BCM_## __cpu ##_XTM_IRQ,		\
+	[IRQ_XTM_DMA0]		= BCM_## __cpu ##_XTM_DMA0_IRQ,		\
+
+static inline int bcm63xx_get_irq_number(enum bcm63xx_irq irq)
+{
+	return bcm63xx_irqs[irq];
+}
+
+/*
+ * return installed memory size
+ */
+unsigned int bcm63xx_get_memory_size(void);
+
+void bcm63xx_machine_halt(void);
+
+void bcm63xx_machine_reboot(void);
+
+#endif /* !BCM63XX_CPU_H_ */
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cs.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cs.h
new file mode 100644
index 000000000..1c634d7c1
--- /dev/null
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cs.h
@@ -0,0 +1,11 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef BCM63XX_CS_H
+#define BCM63XX_CS_H
+
+int bcm63xx_set_cs_base(unsigned int cs, u32 base, unsigned int size);
+int bcm63xx_set_cs_timing(unsigned int cs, unsigned int wait,
+			   unsigned int setup, unsigned int hold);
+int bcm63xx_set_cs_param(unsigned int cs, u32 flags);
+int bcm63xx_set_cs_status(unsigned int cs, int enable);
+
+#endif /* !BCM63XX_CS_H */
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h
new file mode 100644
index 000000000..da39e4d32
--- /dev/null
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h
@@ -0,0 +1,126 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef BCM63XX_DEV_ENET_H_
+#define BCM63XX_DEV_ENET_H_
+
+#include <linux/if_ether.h>
+#include <linux/init.h>
+
+#include <bcm63xx_regs.h>
+
+/*
+ * on board ethernet platform data
+ */
+struct bcm63xx_enet_platform_data {
+	char mac_addr[ETH_ALEN];
+
+	int has_phy;
+
+	/* if has_phy, then set use_internal_phy */
+	int use_internal_phy;
+
+	/* or fill phy info to use an external one */
+	int phy_id;
+	int has_phy_interrupt;
+	int phy_interrupt;
+
+	/* if has_phy, use autonegotiated pause parameters or force
+	 * them */
+	int pause_auto;
+	int pause_rx;
+	int pause_tx;
+
+	/* if !has_phy, set desired forced speed/duplex */
+	int force_speed_100;
+	int force_duplex_full;
+
+	/* if !has_phy, set callback to perform mii device
+	 * init/remove */
+	int (*mii_config)(struct net_device *dev, int probe,
+			  int (*mii_read)(struct net_device *dev,
+					  int phy_id, int reg),
+			  void (*mii_write)(struct net_device *dev,
+					    int phy_id, int reg, int val));
+
+	/* DMA channel enable mask */
+	u32 dma_chan_en_mask;
+
+	/* DMA channel interrupt mask */
+	u32 dma_chan_int_mask;
+
+	/* DMA engine has internal SRAM */
+	bool dma_has_sram;
+
+	/* DMA channel register width */
+	unsigned int dma_chan_width;
+
+	/* DMA descriptor shift */
+	unsigned int dma_desc_shift;
+
+	/* dma channel ids */
+	int rx_chan;
+	int tx_chan;
+};
+
+/*
+ * on board ethernet switch platform data
+ */
+#define ENETSW_MAX_PORT	8
+#define ENETSW_PORTS_6328 5 /* 4 FE PHY + 1 RGMII */
+#define ENETSW_PORTS_6368 6 /* 4 FE PHY + 2 RGMII */
+
+#define ENETSW_RGMII_PORT0	4
+
+struct bcm63xx_enetsw_port {
+	int		used;
+	int		phy_id;
+
+	int		bypass_link;
+	int		force_speed;
+	int		force_duplex_full;
+
+	const char	*name;
+};
+
+struct bcm63xx_enetsw_platform_data {
+	char mac_addr[ETH_ALEN];
+	int num_ports;
+	struct bcm63xx_enetsw_port used_ports[ENETSW_MAX_PORT];
+
+	/* DMA channel enable mask */
+	u32 dma_chan_en_mask;
+
+	/* DMA channel interrupt mask */
+	u32 dma_chan_int_mask;
+
+	/* DMA channel register width */
+	unsigned int dma_chan_width;
+
+	/* DMA engine has internal SRAM */
+	bool dma_has_sram;
+};
+
+int __init bcm63xx_enet_register(int unit,
+				 const struct bcm63xx_enet_platform_data *pd);
+
+int bcm63xx_enetsw_register(const struct bcm63xx_enetsw_platform_data *pd);
+
+enum bcm63xx_regs_enetdmac {
+	ENETDMAC_CHANCFG,
+	ENETDMAC_IR,
+	ENETDMAC_IRMASK,
+	ENETDMAC_MAXBURST,
+	ENETDMAC_BUFALLOC,
+	ENETDMAC_RSTART,
+	ENETDMAC_FC,
+	ENETDMAC_LEN,
+};
+
+static inline unsigned long bcm63xx_enetdmacreg(enum bcm63xx_regs_enetdmac reg)
+{
+	extern const unsigned long *bcm63xx_regs_enetdmac;
+
+	return bcm63xx_regs_enetdmac[reg];
+}
+
+
+#endif /* ! BCM63XX_DEV_ENET_H_ */
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h
new file mode 100644
index 000000000..4d5005f2b
--- /dev/null
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h
@@ -0,0 +1,13 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __BCM63XX_FLASH_H
+#define __BCM63XX_FLASH_H
+
+enum {
+	BCM63XX_FLASH_TYPE_PARALLEL,
+	BCM63XX_FLASH_TYPE_SERIAL,
+	BCM63XX_FLASH_TYPE_NAND,
+};
+
+int __init bcm63xx_flash_register(void);
+
+#endif /* __BCM63XX_FLASH_H */
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h
new file mode 100644
index 000000000..f93f176c1
--- /dev/null
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h
@@ -0,0 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef BCM63XX_DEV_HSSPI_H
+#define BCM63XX_DEV_HSSPI_H
+
+#include <linux/types.h>
+
+int bcm63xx_hsspi_register(void);
+
+#endif /* BCM63XX_DEV_HSSPI_H */
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_pci.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_pci.h
new file mode 100644
index 000000000..1951c125c
--- /dev/null
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_pci.h
@@ -0,0 +1,7 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef BCM63XX_DEV_PCI_H_
+#define BCM63XX_DEV_PCI_H_
+
+extern int bcm63xx_pci_enabled;
+
+#endif /* BCM63XX_DEV_PCI_H_ */
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_pcmcia.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_pcmcia.h
new file mode 100644
index 000000000..01674ac58
--- /dev/null
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_pcmcia.h
@@ -0,0 +1,14 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef BCM63XX_DEV_PCMCIA_H_
+#define BCM63XX_DEV_PCMCIA_H_
+
+/*
+ * PCMCIA driver platform data
+ */
+struct bcm63xx_pcmcia_platform_data {
+	unsigned int ready_gpio;
+};
+
+int bcm63xx_pcmcia_register(void);
+
+#endif /* BCM63XX_DEV_PCMCIA_H_ */
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h
new file mode 100644
index 000000000..0ab750522
--- /dev/null
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h
@@ -0,0 +1,11 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef BCM63XX_DEV_SPI_H
+#define BCM63XX_DEV_SPI_H
+
+#include <linux/types.h>
+#include <bcm63xx_io.h>
+#include <bcm63xx_regs.h>
+
+int __init bcm63xx_spi_register(void);
+
+#endif /* BCM63XX_DEV_SPI_H */
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_uart.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_uart.h
new file mode 100644
index 000000000..88f8cf1c7
--- /dev/null
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_uart.h
@@ -0,0 +1,7 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef BCM63XX_DEV_UART_H_
+#define BCM63XX_DEV_UART_H_
+
+int bcm63xx_uart_register(unsigned int id);
+
+#endif /* BCM63XX_DEV_UART_H_ */
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_usbd.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_usbd.h
new file mode 100644
index 000000000..3f920baff
--- /dev/null
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_usbd.h
@@ -0,0 +1,18 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef BCM63XX_DEV_USB_USBD_H_
+#define BCM63XX_DEV_USB_USBD_H_
+
+/*
+ * usb device platform data
+ */
+struct bcm63xx_usbd_platform_data {
+	/* board can only support full speed (USB 1.1) */
+	int use_fullspeed;
+
+	/* 0-based port index, for chips with >1 USB PHY */
+	int port_no;
+};
+
+int bcm63xx_usbd_register(const struct bcm63xx_usbd_platform_data *pd);
+
+#endif /* BCM63XX_DEV_USB_USBD_H_ */
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h
new file mode 100644
index 000000000..9212429d5
--- /dev/null
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h
@@ -0,0 +1,35 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef BCM63XX_GPIO_H
+#define BCM63XX_GPIO_H
+
+#include <linux/init.h>
+#include <bcm63xx_cpu.h>
+
+int __init bcm63xx_gpio_init(void);
+
+static inline unsigned long bcm63xx_gpio_count(void)
+{
+	switch (bcm63xx_get_cpu_id()) {
+	case BCM6328_CPU_ID:
+		return 32;
+	case BCM3368_CPU_ID:
+		return 40;
+	case BCM6338_CPU_ID:
+		return 8;
+	case BCM6345_CPU_ID:
+		return 16;
+	case BCM6358_CPU_ID:
+	case BCM6368_CPU_ID:
+		return 38;
+	case BCM6362_CPU_ID:
+		return 48;
+	case BCM6348_CPU_ID:
+	default:
+		return 37;
+	}
+}
+
+#define BCM63XX_GPIO_DIR_OUT	0x0
+#define BCM63XX_GPIO_DIR_IN	0x1
+
+#endif /* !BCM63XX_GPIO_H */
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_io.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_io.h
new file mode 100644
index 000000000..31c692433
--- /dev/null
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_io.h
@@ -0,0 +1,104 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef BCM63XX_IO_H_
+#define BCM63XX_IO_H_
+
+#include <asm/mach-bcm63xx/bcm63xx_cpu.h>
+
+/*
+ * Physical memory map, RAM is mapped at 0x0.
+ *
+ * Note that size MUST be a power of two.
+ */
+#define BCM_PCMCIA_COMMON_BASE_PA	(0x20000000)
+#define BCM_PCMCIA_COMMON_SIZE		(16 * 1024 * 1024)
+#define BCM_PCMCIA_COMMON_END_PA	(BCM_PCMCIA_COMMON_BASE_PA +	\
+					 BCM_PCMCIA_COMMON_SIZE - 1)
+
+#define BCM_PCMCIA_ATTR_BASE_PA		(0x21000000)
+#define BCM_PCMCIA_ATTR_SIZE		(16 * 1024 * 1024)
+#define BCM_PCMCIA_ATTR_END_PA		(BCM_PCMCIA_ATTR_BASE_PA +	\
+					 BCM_PCMCIA_ATTR_SIZE - 1)
+
+#define BCM_PCMCIA_IO_BASE_PA		(0x22000000)
+#define BCM_PCMCIA_IO_SIZE		(64 * 1024)
+#define BCM_PCMCIA_IO_END_PA		(BCM_PCMCIA_IO_BASE_PA +	\
+					BCM_PCMCIA_IO_SIZE - 1)
+
+#define BCM_PCI_MEM_BASE_PA		(0x30000000)
+#define BCM_PCI_MEM_SIZE		(128 * 1024 * 1024)
+#define BCM_PCI_MEM_END_PA		(BCM_PCI_MEM_BASE_PA +		\
+					BCM_PCI_MEM_SIZE - 1)
+
+#define BCM_PCI_IO_BASE_PA		(0x08000000)
+#define BCM_PCI_IO_SIZE			(64 * 1024)
+#define BCM_PCI_IO_END_PA		(BCM_PCI_IO_BASE_PA +		\
+					BCM_PCI_IO_SIZE - 1)
+#define BCM_PCI_IO_HALF_PA		(BCM_PCI_IO_BASE_PA +		\
+					(BCM_PCI_IO_SIZE / 2) - 1)
+
+#define BCM_CB_MEM_BASE_PA		(0x38000000)
+#define BCM_CB_MEM_SIZE			(128 * 1024 * 1024)
+#define BCM_CB_MEM_END_PA		(BCM_CB_MEM_BASE_PA +		\
+					BCM_CB_MEM_SIZE - 1)
+
+#define BCM_PCIE_MEM_BASE_PA		0x10f00000
+#define BCM_PCIE_MEM_SIZE		(16 * 1024 * 1024)
+#define BCM_PCIE_MEM_END_PA		(BCM_PCIE_MEM_BASE_PA +		\
+					BCM_PCIE_MEM_SIZE - 1)
+
+/*
+ * Internal registers are accessed through KSEG3
+ */
+#define BCM_REGS_VA(x)	((void __iomem *)(x))
+
+#define bcm_readb(a)	(*(volatile unsigned char *)	BCM_REGS_VA(a))
+#define bcm_readw(a)	(*(volatile unsigned short *)	BCM_REGS_VA(a))
+#define bcm_readl(a)	(*(volatile unsigned int *)	BCM_REGS_VA(a))
+#define bcm_readq(a)	(*(volatile u64 *)		BCM_REGS_VA(a))
+#define bcm_writeb(v, a) (*(volatile unsigned char *) BCM_REGS_VA((a)) = (v))
+#define bcm_writew(v, a) (*(volatile unsigned short *) BCM_REGS_VA((a)) = (v))
+#define bcm_writel(v, a) (*(volatile unsigned int *) BCM_REGS_VA((a)) = (v))
+#define bcm_writeq(v, a) (*(volatile u64 *) BCM_REGS_VA((a)) = (v))
+
+/*
+ * IO helpers to access register set for current CPU
+ */
+#define bcm_rset_readb(s, o)	bcm_readb(bcm63xx_regset_address(s) + (o))
+#define bcm_rset_readw(s, o)	bcm_readw(bcm63xx_regset_address(s) + (o))
+#define bcm_rset_readl(s, o)	bcm_readl(bcm63xx_regset_address(s) + (o))
+#define bcm_rset_writeb(s, v, o)	bcm_writeb((v), \
+					bcm63xx_regset_address(s) + (o))
+#define bcm_rset_writew(s, v, o)	bcm_writew((v), \
+					bcm63xx_regset_address(s) + (o))
+#define bcm_rset_writel(s, v, o)	bcm_writel((v), \
+					bcm63xx_regset_address(s) + (o))
+
+/*
+ * helpers for frequently used register sets
+ */
+#define bcm_perf_readl(o)	bcm_rset_readl(RSET_PERF, (o))
+#define bcm_perf_writel(v, o)	bcm_rset_writel(RSET_PERF, (v), (o))
+#define bcm_timer_readl(o)	bcm_rset_readl(RSET_TIMER, (o))
+#define bcm_timer_writel(v, o)	bcm_rset_writel(RSET_TIMER, (v), (o))
+#define bcm_wdt_readl(o)	bcm_rset_readl(RSET_WDT, (o))
+#define bcm_wdt_writel(v, o)	bcm_rset_writel(RSET_WDT, (v), (o))
+#define bcm_gpio_readl(o)	bcm_rset_readl(RSET_GPIO, (o))
+#define bcm_gpio_writel(v, o)	bcm_rset_writel(RSET_GPIO, (v), (o))
+#define bcm_uart0_readl(o)	bcm_rset_readl(RSET_UART0, (o))
+#define bcm_uart0_writel(v, o)	bcm_rset_writel(RSET_UART0, (v), (o))
+#define bcm_mpi_readl(o)	bcm_rset_readl(RSET_MPI, (o))
+#define bcm_mpi_writel(v, o)	bcm_rset_writel(RSET_MPI, (v), (o))
+#define bcm_pcmcia_readl(o)	bcm_rset_readl(RSET_PCMCIA, (o))
+#define bcm_pcmcia_writel(v, o) bcm_rset_writel(RSET_PCMCIA, (v), (o))
+#define bcm_pcie_readl(o)	bcm_rset_readl(RSET_PCIE, (o))
+#define bcm_pcie_writel(v, o)	bcm_rset_writel(RSET_PCIE, (v), (o))
+#define bcm_sdram_readl(o)	bcm_rset_readl(RSET_SDRAM, (o))
+#define bcm_sdram_writel(v, o)	bcm_rset_writel(RSET_SDRAM, (v), (o))
+#define bcm_memc_readl(o)	bcm_rset_readl(RSET_MEMC, (o))
+#define bcm_memc_writel(v, o)	bcm_rset_writel(RSET_MEMC, (v), (o))
+#define bcm_ddr_readl(o)	bcm_rset_readl(RSET_DDR, (o))
+#define bcm_ddr_writel(v, o)	bcm_rset_writel(RSET_DDR, (v), (o))
+#define bcm_misc_readl(o)	bcm_rset_readl(RSET_MISC, (o))
+#define bcm_misc_writel(v, o)	bcm_rset_writel(RSET_MISC, (v), (o))
+
+#endif /* ! BCM63XX_IO_H_ */
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_irq.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_irq.h
new file mode 100644
index 000000000..7887bc690
--- /dev/null
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_irq.h
@@ -0,0 +1,14 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef BCM63XX_IRQ_H_
+#define BCM63XX_IRQ_H_
+
+#include <bcm63xx_cpu.h>
+
+#define IRQ_INTERNAL_BASE		8
+#define IRQ_EXTERNAL_BASE		100
+#define IRQ_EXT_0			(IRQ_EXTERNAL_BASE + 0)
+#define IRQ_EXT_1			(IRQ_EXTERNAL_BASE + 1)
+#define IRQ_EXT_2			(IRQ_EXTERNAL_BASE + 2)
+#define IRQ_EXT_3			(IRQ_EXTERNAL_BASE + 3)
+
+#endif /* ! BCM63XX_IRQ_H_ */
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_iudma.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_iudma.h
new file mode 100644
index 000000000..73df916e4
--- /dev/null
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_iudma.h
@@ -0,0 +1,39 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef BCM63XX_IUDMA_H_
+#define BCM63XX_IUDMA_H_
+
+#include <linux/types.h>
+
+/*
+ * rx/tx dma descriptor
+ */
+struct bcm_enet_desc {
+	u32 len_stat;
+	u32 address;
+};
+
+/* control */
+#define DMADESC_LENGTH_SHIFT	16
+#define DMADESC_LENGTH_MASK	(0xfff << DMADESC_LENGTH_SHIFT)
+#define DMADESC_OWNER_MASK	(1 << 15)
+#define DMADESC_EOP_MASK	(1 << 14)
+#define DMADESC_SOP_MASK	(1 << 13)
+#define DMADESC_ESOP_MASK	(DMADESC_EOP_MASK | DMADESC_SOP_MASK)
+#define DMADESC_WRAP_MASK	(1 << 12)
+#define DMADESC_USB_NOZERO_MASK (1 << 1)
+#define DMADESC_USB_ZERO_MASK	(1 << 0)
+
+/* status */
+#define DMADESC_UNDER_MASK	(1 << 9)
+#define DMADESC_APPEND_CRC	(1 << 8)
+#define DMADESC_OVSIZE_MASK	(1 << 4)
+#define DMADESC_RXER_MASK	(1 << 2)
+#define DMADESC_CRC_MASK	(1 << 1)
+#define DMADESC_OV_MASK		(1 << 0)
+#define DMADESC_ERR_MASK	(DMADESC_UNDER_MASK | \
+				DMADESC_OVSIZE_MASK | \
+				DMADESC_RXER_MASK | \
+				DMADESC_CRC_MASK | \
+				DMADESC_OV_MASK)
+
+#endif /* ! BCM63XX_IUDMA_H_ */
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_nvram.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_nvram.h
new file mode 100644
index 000000000..f78d725f2
--- /dev/null
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_nvram.h
@@ -0,0 +1,36 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef BCM63XX_NVRAM_H
+#define BCM63XX_NVRAM_H
+
+#include <linux/types.h>
+
+/**
+ * bcm63xx_nvram_init() - initializes nvram
+ * @nvram:	address of the nvram data
+ *
+ * Initialized the local nvram copy from the target address and checks
+ * its checksum.
+ */
+void bcm63xx_nvram_init(void *nvram);
+
+/**
+ * bcm63xx_nvram_get_name() - returns the board name according to nvram
+ *
+ * Returns the board name field from nvram. Note that it might not be
+ * null terminated if it is exactly 16 bytes long.
+ */
+u8 *bcm63xx_nvram_get_name(void);
+
+/**
+ * bcm63xx_nvram_get_mac_address() - register & return a new mac address
+ * @mac:	pointer to array for allocated mac
+ *
+ * Registers and returns a mac address from the allocated macs from nvram.
+ *
+ * Returns 0 on success.
+ */
+int bcm63xx_nvram_get_mac_address(u8 *mac);
+
+int bcm63xx_nvram_get_psi_size(void);
+
+#endif /* BCM63XX_NVRAM_H */
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
new file mode 100644
index 000000000..d3f397dca
--- /dev/null
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
@@ -0,0 +1,1429 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef BCM63XX_REGS_H_
+#define BCM63XX_REGS_H_
+
+/*************************************************************************
+ * _REG relative to RSET_PERF
+ *************************************************************************/
+
+/* Chip Identifier / Revision register */
+#define PERF_REV_REG			0x0
+#define REV_CHIPID_SHIFT		16
+#define REV_CHIPID_MASK			(0xffff << REV_CHIPID_SHIFT)
+#define REV_REVID_SHIFT			0
+#define REV_REVID_MASK			(0xff << REV_REVID_SHIFT)
+
+/* Clock Control register */
+#define PERF_CKCTL_REG			0x4
+
+#define CKCTL_3368_MAC_EN		(1 << 3)
+#define CKCTL_3368_TC_EN		(1 << 5)
+#define CKCTL_3368_US_TOP_EN		(1 << 6)
+#define CKCTL_3368_DS_TOP_EN		(1 << 7)
+#define CKCTL_3368_APM_EN		(1 << 8)
+#define CKCTL_3368_SPI_EN		(1 << 9)
+#define CKCTL_3368_USBS_EN		(1 << 10)
+#define CKCTL_3368_BMU_EN		(1 << 11)
+#define CKCTL_3368_PCM_EN		(1 << 12)
+#define CKCTL_3368_NTP_EN		(1 << 13)
+#define CKCTL_3368_ACP_B_EN		(1 << 14)
+#define CKCTL_3368_ACP_A_EN		(1 << 15)
+#define CKCTL_3368_EMUSB_EN		(1 << 17)
+#define CKCTL_3368_ENET0_EN		(1 << 18)
+#define CKCTL_3368_ENET1_EN		(1 << 19)
+#define CKCTL_3368_USBU_EN		(1 << 20)
+#define CKCTL_3368_EPHY_EN		(1 << 21)
+
+#define CKCTL_3368_ALL_SAFE_EN		(CKCTL_3368_MAC_EN | \
+					 CKCTL_3368_TC_EN | \
+					 CKCTL_3368_US_TOP_EN | \
+					 CKCTL_3368_DS_TOP_EN | \
+					 CKCTL_3368_APM_EN | \
+					 CKCTL_3368_SPI_EN | \
+					 CKCTL_3368_USBS_EN | \
+					 CKCTL_3368_BMU_EN | \
+					 CKCTL_3368_PCM_EN | \
+					 CKCTL_3368_NTP_EN | \
+					 CKCTL_3368_ACP_B_EN | \
+					 CKCTL_3368_ACP_A_EN | \
+					 CKCTL_3368_EMUSB_EN | \
+					 CKCTL_3368_USBU_EN)
+
+#define CKCTL_6328_PHYMIPS_EN		(1 << 0)
+#define CKCTL_6328_ADSL_QPROC_EN	(1 << 1)
+#define CKCTL_6328_ADSL_AFE_EN		(1 << 2)
+#define CKCTL_6328_ADSL_EN		(1 << 3)
+#define CKCTL_6328_MIPS_EN		(1 << 4)
+#define CKCTL_6328_SAR_EN		(1 << 5)
+#define CKCTL_6328_PCM_EN		(1 << 6)
+#define CKCTL_6328_USBD_EN		(1 << 7)
+#define CKCTL_6328_USBH_EN		(1 << 8)
+#define CKCTL_6328_HSSPI_EN		(1 << 9)
+#define CKCTL_6328_PCIE_EN		(1 << 10)
+#define CKCTL_6328_ROBOSW_EN		(1 << 11)
+
+#define CKCTL_6328_ALL_SAFE_EN		(CKCTL_6328_PHYMIPS_EN |	\
+					CKCTL_6328_ADSL_QPROC_EN |	\
+					CKCTL_6328_ADSL_AFE_EN |	\
+					CKCTL_6328_ADSL_EN |		\
+					CKCTL_6328_SAR_EN  |		\
+					CKCTL_6328_PCM_EN  |		\
+					CKCTL_6328_USBD_EN |		\
+					CKCTL_6328_USBH_EN |		\
+					CKCTL_6328_ROBOSW_EN |		\
+					CKCTL_6328_PCIE_EN)
+
+#define CKCTL_6338_ADSLPHY_EN		(1 << 0)
+#define CKCTL_6338_MPI_EN		(1 << 1)
+#define CKCTL_6338_DRAM_EN		(1 << 2)
+#define CKCTL_6338_ENET_EN		(1 << 4)
+#define CKCTL_6338_USBS_EN		(1 << 4)
+#define CKCTL_6338_SAR_EN		(1 << 5)
+#define CKCTL_6338_SPI_EN		(1 << 9)
+
+#define CKCTL_6338_ALL_SAFE_EN		(CKCTL_6338_ADSLPHY_EN |	\
+					CKCTL_6338_MPI_EN |		\
+					CKCTL_6338_ENET_EN |		\
+					CKCTL_6338_SAR_EN |		\
+					CKCTL_6338_SPI_EN)
+
+/* BCM6345 clock bits are shifted by 16 on the left, because of the test
+ * control register which is 16-bits wide. That way we do not have any
+ * specific BCM6345 code for handling clocks, and writing 0 to the test
+ * control register is fine.
+ */
+#define CKCTL_6345_CPU_EN		(1 << 16)
+#define CKCTL_6345_BUS_EN		(1 << 17)
+#define CKCTL_6345_EBI_EN		(1 << 18)
+#define CKCTL_6345_UART_EN		(1 << 19)
+#define CKCTL_6345_ADSLPHY_EN		(1 << 20)
+#define CKCTL_6345_ENET_EN		(1 << 23)
+#define CKCTL_6345_USBH_EN		(1 << 24)
+
+#define CKCTL_6345_ALL_SAFE_EN		(CKCTL_6345_ENET_EN |	\
+					CKCTL_6345_USBH_EN |	\
+					CKCTL_6345_ADSLPHY_EN)
+
+#define CKCTL_6348_ADSLPHY_EN		(1 << 0)
+#define CKCTL_6348_MPI_EN		(1 << 1)
+#define CKCTL_6348_SDRAM_EN		(1 << 2)
+#define CKCTL_6348_M2M_EN		(1 << 3)
+#define CKCTL_6348_ENET_EN		(1 << 4)
+#define CKCTL_6348_SAR_EN		(1 << 5)
+#define CKCTL_6348_USBS_EN		(1 << 6)
+#define CKCTL_6348_USBH_EN		(1 << 8)
+#define CKCTL_6348_SPI_EN		(1 << 9)
+
+#define CKCTL_6348_ALL_SAFE_EN		(CKCTL_6348_ADSLPHY_EN |	\
+					CKCTL_6348_M2M_EN |		\
+					CKCTL_6348_ENET_EN |		\
+					CKCTL_6348_SAR_EN |		\
+					CKCTL_6348_USBS_EN |		\
+					CKCTL_6348_USBH_EN |		\
+					CKCTL_6348_SPI_EN)
+
+#define CKCTL_6358_ENET_EN		(1 << 4)
+#define CKCTL_6358_ADSLPHY_EN		(1 << 5)
+#define CKCTL_6358_PCM_EN		(1 << 8)
+#define CKCTL_6358_SPI_EN		(1 << 9)
+#define CKCTL_6358_USBS_EN		(1 << 10)
+#define CKCTL_6358_SAR_EN		(1 << 11)
+#define CKCTL_6358_EMUSB_EN		(1 << 17)
+#define CKCTL_6358_ENET0_EN		(1 << 18)
+#define CKCTL_6358_ENET1_EN		(1 << 19)
+#define CKCTL_6358_USBSU_EN		(1 << 20)
+#define CKCTL_6358_EPHY_EN		(1 << 21)
+
+#define CKCTL_6358_ALL_SAFE_EN		(CKCTL_6358_ENET_EN |		\
+					CKCTL_6358_ADSLPHY_EN |		\
+					CKCTL_6358_PCM_EN |		\
+					CKCTL_6358_SPI_EN |		\
+					CKCTL_6358_USBS_EN |		\
+					CKCTL_6358_SAR_EN |		\
+					CKCTL_6358_EMUSB_EN |		\
+					CKCTL_6358_ENET0_EN |		\
+					CKCTL_6358_ENET1_EN |		\
+					CKCTL_6358_USBSU_EN |		\
+					CKCTL_6358_EPHY_EN)
+
+#define CKCTL_6362_ADSL_QPROC_EN	(1 << 1)
+#define CKCTL_6362_ADSL_AFE_EN		(1 << 2)
+#define CKCTL_6362_ADSL_EN		(1 << 3)
+#define CKCTL_6362_MIPS_EN		(1 << 4)
+#define CKCTL_6362_WLAN_OCP_EN		(1 << 5)
+#define CKCTL_6362_SWPKT_USB_EN		(1 << 7)
+#define CKCTL_6362_SWPKT_SAR_EN		(1 << 8)
+#define CKCTL_6362_SAR_EN		(1 << 9)
+#define CKCTL_6362_ROBOSW_EN		(1 << 10)
+#define CKCTL_6362_PCM_EN		(1 << 11)
+#define CKCTL_6362_USBD_EN		(1 << 12)
+#define CKCTL_6362_USBH_EN		(1 << 13)
+#define CKCTL_6362_IPSEC_EN		(1 << 14)
+#define CKCTL_6362_SPI_EN		(1 << 15)
+#define CKCTL_6362_HSSPI_EN		(1 << 16)
+#define CKCTL_6362_PCIE_EN		(1 << 17)
+#define CKCTL_6362_FAP_EN		(1 << 18)
+#define CKCTL_6362_PHYMIPS_EN		(1 << 19)
+#define CKCTL_6362_NAND_EN		(1 << 20)
+
+#define CKCTL_6362_ALL_SAFE_EN		(CKCTL_6362_PHYMIPS_EN |	\
+					CKCTL_6362_ADSL_QPROC_EN |	\
+					CKCTL_6362_ADSL_AFE_EN |	\
+					CKCTL_6362_ADSL_EN |		\
+					CKCTL_6362_SAR_EN  |		\
+					CKCTL_6362_PCM_EN  |		\
+					CKCTL_6362_IPSEC_EN |		\
+					CKCTL_6362_USBD_EN |		\
+					CKCTL_6362_USBH_EN |		\
+					CKCTL_6362_ROBOSW_EN |		\
+					CKCTL_6362_PCIE_EN)
+
+
+#define CKCTL_6368_VDSL_QPROC_EN	(1 << 2)
+#define CKCTL_6368_VDSL_AFE_EN		(1 << 3)
+#define CKCTL_6368_VDSL_BONDING_EN	(1 << 4)
+#define CKCTL_6368_VDSL_EN		(1 << 5)
+#define CKCTL_6368_PHYMIPS_EN		(1 << 6)
+#define CKCTL_6368_SWPKT_USB_EN		(1 << 7)
+#define CKCTL_6368_SWPKT_SAR_EN		(1 << 8)
+#define CKCTL_6368_SPI_EN		(1 << 9)
+#define CKCTL_6368_USBD_EN		(1 << 10)
+#define CKCTL_6368_SAR_EN		(1 << 11)
+#define CKCTL_6368_ROBOSW_EN		(1 << 12)
+#define CKCTL_6368_UTOPIA_EN		(1 << 13)
+#define CKCTL_6368_PCM_EN		(1 << 14)
+#define CKCTL_6368_USBH_EN		(1 << 15)
+#define CKCTL_6368_DISABLE_GLESS_EN	(1 << 16)
+#define CKCTL_6368_NAND_EN		(1 << 17)
+#define CKCTL_6368_IPSEC_EN		(1 << 18)
+
+#define CKCTL_6368_ALL_SAFE_EN		(CKCTL_6368_SWPKT_USB_EN |	\
+					CKCTL_6368_SWPKT_SAR_EN |	\
+					CKCTL_6368_SPI_EN |		\
+					CKCTL_6368_USBD_EN |		\
+					CKCTL_6368_SAR_EN |		\
+					CKCTL_6368_ROBOSW_EN |		\
+					CKCTL_6368_UTOPIA_EN |		\
+					CKCTL_6368_PCM_EN |		\
+					CKCTL_6368_USBH_EN |		\
+					CKCTL_6368_DISABLE_GLESS_EN |	\
+					CKCTL_6368_NAND_EN |		\
+					CKCTL_6368_IPSEC_EN)
+
+/* System PLL Control register	*/
+#define PERF_SYS_PLL_CTL_REG		0x8
+#define SYS_PLL_SOFT_RESET		0x1
+
+/* Interrupt Mask register */
+#define PERF_IRQMASK_3368_REG		0xc
+#define PERF_IRQMASK_6328_REG(x)	(0x20 + (x) * 0x10)
+#define PERF_IRQMASK_6338_REG		0xc
+#define PERF_IRQMASK_6345_REG		0xc
+#define PERF_IRQMASK_6348_REG		0xc
+#define PERF_IRQMASK_6358_REG(x)	(0xc + (x) * 0x2c)
+#define PERF_IRQMASK_6362_REG(x)	(0x20 + (x) * 0x10)
+#define PERF_IRQMASK_6368_REG(x)	(0x20 + (x) * 0x10)
+
+/* Interrupt Status register */
+#define PERF_IRQSTAT_3368_REG		0x10
+#define PERF_IRQSTAT_6328_REG(x)	(0x28 + (x) * 0x10)
+#define PERF_IRQSTAT_6338_REG		0x10
+#define PERF_IRQSTAT_6345_REG		0x10
+#define PERF_IRQSTAT_6348_REG		0x10
+#define PERF_IRQSTAT_6358_REG(x)	(0x10 + (x) * 0x2c)
+#define PERF_IRQSTAT_6362_REG(x)	(0x28 + (x) * 0x10)
+#define PERF_IRQSTAT_6368_REG(x)	(0x28 + (x) * 0x10)
+
+/* External Interrupt Configuration register */
+#define PERF_EXTIRQ_CFG_REG_3368	0x14
+#define PERF_EXTIRQ_CFG_REG_6328	0x18
+#define PERF_EXTIRQ_CFG_REG_6338	0x14
+#define PERF_EXTIRQ_CFG_REG_6345	0x14
+#define PERF_EXTIRQ_CFG_REG_6348	0x14
+#define PERF_EXTIRQ_CFG_REG_6358	0x14
+#define PERF_EXTIRQ_CFG_REG_6362	0x18
+#define PERF_EXTIRQ_CFG_REG_6368	0x18
+
+#define PERF_EXTIRQ_CFG_REG2_6368	0x1c
+
+/* for 6348 only */
+#define EXTIRQ_CFG_SENSE_6348(x)	(1 << (x))
+#define EXTIRQ_CFG_STAT_6348(x)		(1 << (x + 5))
+#define EXTIRQ_CFG_CLEAR_6348(x)	(1 << (x + 10))
+#define EXTIRQ_CFG_MASK_6348(x)		(1 << (x + 15))
+#define EXTIRQ_CFG_BOTHEDGE_6348(x)	(1 << (x + 20))
+#define EXTIRQ_CFG_LEVELSENSE_6348(x)	(1 << (x + 25))
+#define EXTIRQ_CFG_CLEAR_ALL_6348	(0xf << 10)
+#define EXTIRQ_CFG_MASK_ALL_6348	(0xf << 15)
+
+/* for all others */
+#define EXTIRQ_CFG_SENSE(x)		(1 << (x))
+#define EXTIRQ_CFG_STAT(x)		(1 << (x + 4))
+#define EXTIRQ_CFG_CLEAR(x)		(1 << (x + 8))
+#define EXTIRQ_CFG_MASK(x)		(1 << (x + 12))
+#define EXTIRQ_CFG_BOTHEDGE(x)		(1 << (x + 16))
+#define EXTIRQ_CFG_LEVELSENSE(x)	(1 << (x + 20))
+#define EXTIRQ_CFG_CLEAR_ALL		(0xf << 8)
+#define EXTIRQ_CFG_MASK_ALL		(0xf << 12)
+
+/* Soft Reset register */
+#define PERF_SOFTRESET_REG		0x28
+#define PERF_SOFTRESET_6328_REG		0x10
+#define PERF_SOFTRESET_6358_REG		0x34
+#define PERF_SOFTRESET_6362_REG		0x10
+#define PERF_SOFTRESET_6368_REG		0x10
+
+#define SOFTRESET_3368_SPI_MASK		(1 << 0)
+#define SOFTRESET_3368_ENET_MASK	(1 << 2)
+#define SOFTRESET_3368_MPI_MASK		(1 << 3)
+#define SOFTRESET_3368_EPHY_MASK	(1 << 6)
+#define SOFTRESET_3368_USBS_MASK	(1 << 11)
+#define SOFTRESET_3368_PCM_MASK		(1 << 13)
+
+#define SOFTRESET_6328_SPI_MASK		(1 << 0)
+#define SOFTRESET_6328_EPHY_MASK	(1 << 1)
+#define SOFTRESET_6328_SAR_MASK		(1 << 2)
+#define SOFTRESET_6328_ENETSW_MASK	(1 << 3)
+#define SOFTRESET_6328_USBS_MASK	(1 << 4)
+#define SOFTRESET_6328_USBH_MASK	(1 << 5)
+#define SOFTRESET_6328_PCM_MASK		(1 << 6)
+#define SOFTRESET_6328_PCIE_CORE_MASK	(1 << 7)
+#define SOFTRESET_6328_PCIE_MASK	(1 << 8)
+#define SOFTRESET_6328_PCIE_EXT_MASK	(1 << 9)
+#define SOFTRESET_6328_PCIE_HARD_MASK	(1 << 10)
+
+#define SOFTRESET_6338_SPI_MASK		(1 << 0)
+#define SOFTRESET_6338_ENET_MASK	(1 << 2)
+#define SOFTRESET_6338_USBH_MASK	(1 << 3)
+#define SOFTRESET_6338_USBS_MASK	(1 << 4)
+#define SOFTRESET_6338_ADSL_MASK	(1 << 5)
+#define SOFTRESET_6338_DMAMEM_MASK	(1 << 6)
+#define SOFTRESET_6338_SAR_MASK		(1 << 7)
+#define SOFTRESET_6338_ACLC_MASK	(1 << 8)
+#define SOFTRESET_6338_ADSLMIPSPLL_MASK (1 << 10)
+#define SOFTRESET_6338_ALL	 (SOFTRESET_6338_SPI_MASK |		\
+				  SOFTRESET_6338_ENET_MASK |		\
+				  SOFTRESET_6338_USBH_MASK |		\
+				  SOFTRESET_6338_USBS_MASK |		\
+				  SOFTRESET_6338_ADSL_MASK |		\
+				  SOFTRESET_6338_DMAMEM_MASK |		\
+				  SOFTRESET_6338_SAR_MASK |		\
+				  SOFTRESET_6338_ACLC_MASK |		\
+				  SOFTRESET_6338_ADSLMIPSPLL_MASK)
+
+#define SOFTRESET_6348_SPI_MASK		(1 << 0)
+#define SOFTRESET_6348_ENET_MASK	(1 << 2)
+#define SOFTRESET_6348_USBH_MASK	(1 << 3)
+#define SOFTRESET_6348_USBS_MASK	(1 << 4)
+#define SOFTRESET_6348_ADSL_MASK	(1 << 5)
+#define SOFTRESET_6348_DMAMEM_MASK	(1 << 6)
+#define SOFTRESET_6348_SAR_MASK		(1 << 7)
+#define SOFTRESET_6348_ACLC_MASK	(1 << 8)
+#define SOFTRESET_6348_ADSLMIPSPLL_MASK (1 << 10)
+
+#define SOFTRESET_6348_ALL	 (SOFTRESET_6348_SPI_MASK |		\
+				  SOFTRESET_6348_ENET_MASK |		\
+				  SOFTRESET_6348_USBH_MASK |		\
+				  SOFTRESET_6348_USBS_MASK |		\
+				  SOFTRESET_6348_ADSL_MASK |		\
+				  SOFTRESET_6348_DMAMEM_MASK |		\
+				  SOFTRESET_6348_SAR_MASK |		\
+				  SOFTRESET_6348_ACLC_MASK |		\
+				  SOFTRESET_6348_ADSLMIPSPLL_MASK)
+
+#define SOFTRESET_6358_SPI_MASK		(1 << 0)
+#define SOFTRESET_6358_ENET_MASK	(1 << 2)
+#define SOFTRESET_6358_MPI_MASK		(1 << 3)
+#define SOFTRESET_6358_EPHY_MASK	(1 << 6)
+#define SOFTRESET_6358_SAR_MASK		(1 << 7)
+#define SOFTRESET_6358_USBH_MASK	(1 << 12)
+#define SOFTRESET_6358_PCM_MASK		(1 << 13)
+#define SOFTRESET_6358_ADSL_MASK	(1 << 14)
+
+#define SOFTRESET_6362_SPI_MASK		(1 << 0)
+#define SOFTRESET_6362_IPSEC_MASK	(1 << 1)
+#define SOFTRESET_6362_EPHY_MASK	(1 << 2)
+#define SOFTRESET_6362_SAR_MASK		(1 << 3)
+#define SOFTRESET_6362_ENETSW_MASK	(1 << 4)
+#define SOFTRESET_6362_USBS_MASK	(1 << 5)
+#define SOFTRESET_6362_USBH_MASK	(1 << 6)
+#define SOFTRESET_6362_PCM_MASK		(1 << 7)
+#define SOFTRESET_6362_PCIE_CORE_MASK	(1 << 8)
+#define SOFTRESET_6362_PCIE_MASK	(1 << 9)
+#define SOFTRESET_6362_PCIE_EXT_MASK	(1 << 10)
+#define SOFTRESET_6362_WLAN_SHIM_MASK	(1 << 11)
+#define SOFTRESET_6362_DDR_PHY_MASK	(1 << 12)
+#define SOFTRESET_6362_FAP_MASK		(1 << 13)
+#define SOFTRESET_6362_WLAN_UBUS_MASK	(1 << 14)
+
+#define SOFTRESET_6368_SPI_MASK		(1 << 0)
+#define SOFTRESET_6368_MPI_MASK		(1 << 3)
+#define SOFTRESET_6368_EPHY_MASK	(1 << 6)
+#define SOFTRESET_6368_SAR_MASK		(1 << 7)
+#define SOFTRESET_6368_ENETSW_MASK	(1 << 10)
+#define SOFTRESET_6368_USBS_MASK	(1 << 11)
+#define SOFTRESET_6368_USBH_MASK	(1 << 12)
+#define SOFTRESET_6368_PCM_MASK		(1 << 13)
+
+/* MIPS PLL control register */
+#define PERF_MIPSPLLCTL_REG		0x34
+#define MIPSPLLCTL_N1_SHIFT		20
+#define MIPSPLLCTL_N1_MASK		(0x7 << MIPSPLLCTL_N1_SHIFT)
+#define MIPSPLLCTL_N2_SHIFT		15
+#define MIPSPLLCTL_N2_MASK		(0x1f << MIPSPLLCTL_N2_SHIFT)
+#define MIPSPLLCTL_M1REF_SHIFT		12
+#define MIPSPLLCTL_M1REF_MASK		(0x7 << MIPSPLLCTL_M1REF_SHIFT)
+#define MIPSPLLCTL_M2REF_SHIFT		9
+#define MIPSPLLCTL_M2REF_MASK		(0x7 << MIPSPLLCTL_M2REF_SHIFT)
+#define MIPSPLLCTL_M1CPU_SHIFT		6
+#define MIPSPLLCTL_M1CPU_MASK		(0x7 << MIPSPLLCTL_M1CPU_SHIFT)
+#define MIPSPLLCTL_M1BUS_SHIFT		3
+#define MIPSPLLCTL_M1BUS_MASK		(0x7 << MIPSPLLCTL_M1BUS_SHIFT)
+#define MIPSPLLCTL_M2BUS_SHIFT		0
+#define MIPSPLLCTL_M2BUS_MASK		(0x7 << MIPSPLLCTL_M2BUS_SHIFT)
+
+/* ADSL PHY PLL Control register */
+#define PERF_ADSLPLLCTL_REG		0x38
+#define ADSLPLLCTL_N1_SHIFT		20
+#define ADSLPLLCTL_N1_MASK		(0x7 << ADSLPLLCTL_N1_SHIFT)
+#define ADSLPLLCTL_N2_SHIFT		15
+#define ADSLPLLCTL_N2_MASK		(0x1f << ADSLPLLCTL_N2_SHIFT)
+#define ADSLPLLCTL_M1REF_SHIFT		12
+#define ADSLPLLCTL_M1REF_MASK		(0x7 << ADSLPLLCTL_M1REF_SHIFT)
+#define ADSLPLLCTL_M2REF_SHIFT		9
+#define ADSLPLLCTL_M2REF_MASK		(0x7 << ADSLPLLCTL_M2REF_SHIFT)
+#define ADSLPLLCTL_M1CPU_SHIFT		6
+#define ADSLPLLCTL_M1CPU_MASK		(0x7 << ADSLPLLCTL_M1CPU_SHIFT)
+#define ADSLPLLCTL_M1BUS_SHIFT		3
+#define ADSLPLLCTL_M1BUS_MASK		(0x7 << ADSLPLLCTL_M1BUS_SHIFT)
+#define ADSLPLLCTL_M2BUS_SHIFT		0
+#define ADSLPLLCTL_M2BUS_MASK		(0x7 << ADSLPLLCTL_M2BUS_SHIFT)
+
+#define ADSLPLLCTL_VAL(n1, n2, m1ref, m2ref, m1cpu, m1bus, m2bus)	\
+				(((n1) << ADSLPLLCTL_N1_SHIFT) |	\
+				((n2) << ADSLPLLCTL_N2_SHIFT) |		\
+				((m1ref) << ADSLPLLCTL_M1REF_SHIFT) |	\
+				((m2ref) << ADSLPLLCTL_M2REF_SHIFT) |	\
+				((m1cpu) << ADSLPLLCTL_M1CPU_SHIFT) |	\
+				((m1bus) << ADSLPLLCTL_M1BUS_SHIFT) |	\
+				((m2bus) << ADSLPLLCTL_M2BUS_SHIFT))
+
+
+/*************************************************************************
+ * _REG relative to RSET_TIMER
+ *************************************************************************/
+
+#define BCM63XX_TIMER_COUNT		4
+#define TIMER_T0_ID			0
+#define TIMER_T1_ID			1
+#define TIMER_T2_ID			2
+#define TIMER_WDT_ID			3
+
+/* Timer irqstat register */
+#define TIMER_IRQSTAT_REG		0
+#define TIMER_IRQSTAT_TIMER_CAUSE(x)	(1 << (x))
+#define TIMER_IRQSTAT_TIMER0_CAUSE	(1 << 0)
+#define TIMER_IRQSTAT_TIMER1_CAUSE	(1 << 1)
+#define TIMER_IRQSTAT_TIMER2_CAUSE	(1 << 2)
+#define TIMER_IRQSTAT_WDT_CAUSE		(1 << 3)
+#define TIMER_IRQSTAT_TIMER_IR_EN(x)	(1 << ((x) + 8))
+#define TIMER_IRQSTAT_TIMER0_IR_EN	(1 << 8)
+#define TIMER_IRQSTAT_TIMER1_IR_EN	(1 << 9)
+#define TIMER_IRQSTAT_TIMER2_IR_EN	(1 << 10)
+
+/* Timer control register */
+#define TIMER_CTLx_REG(x)		(0x4 + (x * 4))
+#define TIMER_CTL0_REG			0x4
+#define TIMER_CTL1_REG			0x8
+#define TIMER_CTL2_REG			0xC
+#define TIMER_CTL_COUNTDOWN_MASK	(0x3fffffff)
+#define TIMER_CTL_MONOTONIC_MASK	(1 << 30)
+#define TIMER_CTL_ENABLE_MASK		(1 << 31)
+
+
+/*************************************************************************
+ * _REG relative to RSET_WDT
+ *************************************************************************/
+
+/* Watchdog default count register */
+#define WDT_DEFVAL_REG			0x0
+
+/* Watchdog control register */
+#define WDT_CTL_REG			0x4
+
+/* Watchdog control register constants */
+#define WDT_START_1			(0xff00)
+#define WDT_START_2			(0x00ff)
+#define WDT_STOP_1			(0xee00)
+#define WDT_STOP_2			(0x00ee)
+
+/* Watchdog reset length register */
+#define WDT_RSTLEN_REG			0x8
+
+/* Watchdog soft reset register (BCM6328 only) */
+#define WDT_SOFTRESET_REG		0xc
+
+/*************************************************************************
+ * _REG relative to RSET_GPIO
+ *************************************************************************/
+
+/* GPIO registers */
+#define GPIO_CTL_HI_REG			0x0
+#define GPIO_CTL_LO_REG			0x4
+#define GPIO_DATA_HI_REG		0x8
+#define GPIO_DATA_LO_REG		0xC
+#define GPIO_DATA_LO_REG_6345		0x8
+
+/* GPIO mux registers and constants */
+#define GPIO_MODE_REG			0x18
+
+#define GPIO_MODE_6348_G4_DIAG		0x00090000
+#define GPIO_MODE_6348_G4_UTOPIA	0x00080000
+#define GPIO_MODE_6348_G4_LEGACY_LED	0x00030000
+#define GPIO_MODE_6348_G4_MII_SNOOP	0x00020000
+#define GPIO_MODE_6348_G4_EXT_EPHY	0x00010000
+#define GPIO_MODE_6348_G3_DIAG		0x00009000
+#define GPIO_MODE_6348_G3_UTOPIA	0x00008000
+#define GPIO_MODE_6348_G3_EXT_MII	0x00007000
+#define GPIO_MODE_6348_G2_DIAG		0x00000900
+#define GPIO_MODE_6348_G2_PCI		0x00000500
+#define GPIO_MODE_6348_G1_DIAG		0x00000090
+#define GPIO_MODE_6348_G1_UTOPIA	0x00000080
+#define GPIO_MODE_6348_G1_SPI_UART	0x00000060
+#define GPIO_MODE_6348_G1_SPI_MASTER	0x00000060
+#define GPIO_MODE_6348_G1_MII_PCCARD	0x00000040
+#define GPIO_MODE_6348_G1_MII_SNOOP	0x00000020
+#define GPIO_MODE_6348_G1_EXT_EPHY	0x00000010
+#define GPIO_MODE_6348_G0_DIAG		0x00000009
+#define GPIO_MODE_6348_G0_EXT_MII	0x00000007
+
+#define GPIO_MODE_6358_EXTRACS		(1 << 5)
+#define GPIO_MODE_6358_UART1		(1 << 6)
+#define GPIO_MODE_6358_EXTRA_SPI_SS	(1 << 7)
+#define GPIO_MODE_6358_SERIAL_LED	(1 << 10)
+#define GPIO_MODE_6358_UTOPIA		(1 << 12)
+
+#define GPIO_MODE_6368_ANALOG_AFE_0	(1 << 0)
+#define GPIO_MODE_6368_ANALOG_AFE_1	(1 << 1)
+#define GPIO_MODE_6368_SYS_IRQ		(1 << 2)
+#define GPIO_MODE_6368_SERIAL_LED_DATA	(1 << 3)
+#define GPIO_MODE_6368_SERIAL_LED_CLK	(1 << 4)
+#define GPIO_MODE_6368_INET_LED		(1 << 5)
+#define GPIO_MODE_6368_EPHY0_LED	(1 << 6)
+#define GPIO_MODE_6368_EPHY1_LED	(1 << 7)
+#define GPIO_MODE_6368_EPHY2_LED	(1 << 8)
+#define GPIO_MODE_6368_EPHY3_LED	(1 << 9)
+#define GPIO_MODE_6368_ROBOSW_LED_DAT	(1 << 10)
+#define GPIO_MODE_6368_ROBOSW_LED_CLK	(1 << 11)
+#define GPIO_MODE_6368_ROBOSW_LED0	(1 << 12)
+#define GPIO_MODE_6368_ROBOSW_LED1	(1 << 13)
+#define GPIO_MODE_6368_USBD_LED		(1 << 14)
+#define GPIO_MODE_6368_NTR_PULSE	(1 << 15)
+#define GPIO_MODE_6368_PCI_REQ1		(1 << 16)
+#define GPIO_MODE_6368_PCI_GNT1		(1 << 17)
+#define GPIO_MODE_6368_PCI_INTB		(1 << 18)
+#define GPIO_MODE_6368_PCI_REQ0		(1 << 19)
+#define GPIO_MODE_6368_PCI_GNT0		(1 << 20)
+#define GPIO_MODE_6368_PCMCIA_CD1	(1 << 22)
+#define GPIO_MODE_6368_PCMCIA_CD2	(1 << 23)
+#define GPIO_MODE_6368_PCMCIA_VS1	(1 << 24)
+#define GPIO_MODE_6368_PCMCIA_VS2	(1 << 25)
+#define GPIO_MODE_6368_EBI_CS2		(1 << 26)
+#define GPIO_MODE_6368_EBI_CS3		(1 << 27)
+#define GPIO_MODE_6368_SPI_SSN2		(1 << 28)
+#define GPIO_MODE_6368_SPI_SSN3		(1 << 29)
+#define GPIO_MODE_6368_SPI_SSN4		(1 << 30)
+#define GPIO_MODE_6368_SPI_SSN5		(1 << 31)
+
+
+#define GPIO_PINMUX_OTHR_REG		0x24
+#define GPIO_PINMUX_OTHR_6328_USB_SHIFT 12
+#define GPIO_PINMUX_OTHR_6328_USB_MASK	(3 << GPIO_PINMUX_OTHR_6328_USB_SHIFT)
+#define GPIO_PINMUX_OTHR_6328_USB_HOST	(1 << GPIO_PINMUX_OTHR_6328_USB_SHIFT)
+#define GPIO_PINMUX_OTHR_6328_USB_DEV	(2 << GPIO_PINMUX_OTHR_6328_USB_SHIFT)
+
+#define GPIO_BASEMODE_6368_REG		0x38
+#define GPIO_BASEMODE_6368_UART2	0x1
+#define GPIO_BASEMODE_6368_GPIO		0x0
+#define GPIO_BASEMODE_6368_MASK		0x7
+/* those bits must be kept as read in gpio basemode register*/
+
+#define GPIO_STRAPBUS_REG		0x40
+#define STRAPBUS_6358_BOOT_SEL_PARALLEL (1 << 1)
+#define STRAPBUS_6358_BOOT_SEL_SERIAL	(0 << 1)
+#define STRAPBUS_6368_BOOT_SEL_MASK	0x3
+#define STRAPBUS_6368_BOOT_SEL_NAND	0
+#define STRAPBUS_6368_BOOT_SEL_SERIAL	1
+#define STRAPBUS_6368_BOOT_SEL_PARALLEL 3
+
+
+/*************************************************************************
+ * _REG relative to RSET_ENET
+ *************************************************************************/
+
+/* Receiver Configuration register */
+#define ENET_RXCFG_REG			0x0
+#define ENET_RXCFG_ALLMCAST_SHIFT	1
+#define ENET_RXCFG_ALLMCAST_MASK	(1 << ENET_RXCFG_ALLMCAST_SHIFT)
+#define ENET_RXCFG_PROMISC_SHIFT	3
+#define ENET_RXCFG_PROMISC_MASK		(1 << ENET_RXCFG_PROMISC_SHIFT)
+#define ENET_RXCFG_LOOPBACK_SHIFT	4
+#define ENET_RXCFG_LOOPBACK_MASK	(1 << ENET_RXCFG_LOOPBACK_SHIFT)
+#define ENET_RXCFG_ENFLOW_SHIFT		5
+#define ENET_RXCFG_ENFLOW_MASK		(1 << ENET_RXCFG_ENFLOW_SHIFT)
+
+/* Receive Maximum Length register */
+#define ENET_RXMAXLEN_REG		0x4
+#define ENET_RXMAXLEN_SHIFT		0
+#define ENET_RXMAXLEN_MASK		(0x7ff << ENET_RXMAXLEN_SHIFT)
+
+/* Transmit Maximum Length register */
+#define ENET_TXMAXLEN_REG		0x8
+#define ENET_TXMAXLEN_SHIFT		0
+#define ENET_TXMAXLEN_MASK		(0x7ff << ENET_TXMAXLEN_SHIFT)
+
+/* MII Status/Control register */
+#define ENET_MIISC_REG			0x10
+#define ENET_MIISC_MDCFREQDIV_SHIFT	0
+#define ENET_MIISC_MDCFREQDIV_MASK	(0x7f << ENET_MIISC_MDCFREQDIV_SHIFT)
+#define ENET_MIISC_PREAMBLEEN_SHIFT	7
+#define ENET_MIISC_PREAMBLEEN_MASK	(1 << ENET_MIISC_PREAMBLEEN_SHIFT)
+
+/* MII Data register */
+#define ENET_MIIDATA_REG		0x14
+#define ENET_MIIDATA_DATA_SHIFT		0
+#define ENET_MIIDATA_DATA_MASK		(0xffff << ENET_MIIDATA_DATA_SHIFT)
+#define ENET_MIIDATA_TA_SHIFT		16
+#define ENET_MIIDATA_TA_MASK		(0x3 << ENET_MIIDATA_TA_SHIFT)
+#define ENET_MIIDATA_REG_SHIFT		18
+#define ENET_MIIDATA_REG_MASK		(0x1f << ENET_MIIDATA_REG_SHIFT)
+#define ENET_MIIDATA_PHYID_SHIFT	23
+#define ENET_MIIDATA_PHYID_MASK		(0x1f << ENET_MIIDATA_PHYID_SHIFT)
+#define ENET_MIIDATA_OP_READ_MASK	(0x6 << 28)
+#define ENET_MIIDATA_OP_WRITE_MASK	(0x5 << 28)
+
+/* Ethernet Interrupt Mask register */
+#define ENET_IRMASK_REG			0x18
+
+/* Ethernet Interrupt register */
+#define ENET_IR_REG			0x1c
+#define ENET_IR_MII			(1 << 0)
+#define ENET_IR_MIB			(1 << 1)
+#define ENET_IR_FLOWC			(1 << 2)
+
+/* Ethernet Control register */
+#define ENET_CTL_REG			0x2c
+#define ENET_CTL_ENABLE_SHIFT		0
+#define ENET_CTL_ENABLE_MASK		(1 << ENET_CTL_ENABLE_SHIFT)
+#define ENET_CTL_DISABLE_SHIFT		1
+#define ENET_CTL_DISABLE_MASK		(1 << ENET_CTL_DISABLE_SHIFT)
+#define ENET_CTL_SRESET_SHIFT		2
+#define ENET_CTL_SRESET_MASK		(1 << ENET_CTL_SRESET_SHIFT)
+#define ENET_CTL_EPHYSEL_SHIFT		3
+#define ENET_CTL_EPHYSEL_MASK		(1 << ENET_CTL_EPHYSEL_SHIFT)
+
+/* Transmit Control register */
+#define ENET_TXCTL_REG			0x30
+#define ENET_TXCTL_FD_SHIFT		0
+#define ENET_TXCTL_FD_MASK		(1 << ENET_TXCTL_FD_SHIFT)
+
+/* Transmit Watermask register */
+#define ENET_TXWMARK_REG		0x34
+#define ENET_TXWMARK_WM_SHIFT		0
+#define ENET_TXWMARK_WM_MASK		(0x3f << ENET_TXWMARK_WM_SHIFT)
+
+/* MIB Control register */
+#define ENET_MIBCTL_REG			0x38
+#define ENET_MIBCTL_RDCLEAR_SHIFT	0
+#define ENET_MIBCTL_RDCLEAR_MASK	(1 << ENET_MIBCTL_RDCLEAR_SHIFT)
+
+/* Perfect Match Data Low register */
+#define ENET_PML_REG(x)			(0x58 + (x) * 8)
+#define ENET_PMH_REG(x)			(0x5c + (x) * 8)
+#define ENET_PMH_DATAVALID_SHIFT	16
+#define ENET_PMH_DATAVALID_MASK		(1 << ENET_PMH_DATAVALID_SHIFT)
+
+/* MIB register */
+#define ENET_MIB_REG(x)			(0x200 + (x) * 4)
+#define ENET_MIB_REG_COUNT		55
+
+
+/*************************************************************************
+ * _REG relative to RSET_ENETDMA
+ *************************************************************************/
+#define ENETDMA_CHAN_WIDTH		0x10
+#define ENETDMA_6345_CHAN_WIDTH		0x40
+
+/* Controller Configuration Register */
+#define ENETDMA_CFG_REG			(0x0)
+#define ENETDMA_CFG_EN_SHIFT		0
+#define ENETDMA_CFG_EN_MASK		(1 << ENETDMA_CFG_EN_SHIFT)
+#define ENETDMA_CFG_FLOWCH_MASK(x)	(1 << ((x >> 1) + 1))
+
+/* Flow Control Descriptor Low Threshold register */
+#define ENETDMA_FLOWCL_REG(x)		(0x4 + (x) * 6)
+
+/* Flow Control Descriptor High Threshold register */
+#define ENETDMA_FLOWCH_REG(x)		(0x8 + (x) * 6)
+
+/* Flow Control Descriptor Buffer Alloca Threshold register */
+#define ENETDMA_BUFALLOC_REG(x)		(0xc + (x) * 6)
+#define ENETDMA_BUFALLOC_FORCE_SHIFT	31
+#define ENETDMA_BUFALLOC_FORCE_MASK	(1 << ENETDMA_BUFALLOC_FORCE_SHIFT)
+
+/* Global interrupt status */
+#define ENETDMA_GLB_IRQSTAT_REG		(0x40)
+
+/* Global interrupt mask */
+#define ENETDMA_GLB_IRQMASK_REG		(0x44)
+
+/* Channel Configuration register */
+#define ENETDMA_CHANCFG_REG(x)		(0x100 + (x) * 0x10)
+#define ENETDMA_CHANCFG_EN_SHIFT	0
+#define ENETDMA_CHANCFG_EN_MASK		(1 << ENETDMA_CHANCFG_EN_SHIFT)
+#define ENETDMA_CHANCFG_PKTHALT_SHIFT	1
+#define ENETDMA_CHANCFG_PKTHALT_MASK	(1 << ENETDMA_CHANCFG_PKTHALT_SHIFT)
+
+/* Interrupt Control/Status register */
+#define ENETDMA_IR_REG(x)		(0x104 + (x) * 0x10)
+#define ENETDMA_IR_BUFDONE_MASK		(1 << 0)
+#define ENETDMA_IR_PKTDONE_MASK		(1 << 1)
+#define ENETDMA_IR_NOTOWNER_MASK	(1 << 2)
+
+/* Interrupt Mask register */
+#define ENETDMA_IRMASK_REG(x)		(0x108 + (x) * 0x10)
+
+/* Maximum Burst Length */
+#define ENETDMA_MAXBURST_REG(x)		(0x10C + (x) * 0x10)
+
+/* Ring Start Address register */
+#define ENETDMA_RSTART_REG(x)		(0x200 + (x) * 0x10)
+
+/* State Ram Word 2 */
+#define ENETDMA_SRAM2_REG(x)		(0x204 + (x) * 0x10)
+
+/* State Ram Word 3 */
+#define ENETDMA_SRAM3_REG(x)		(0x208 + (x) * 0x10)
+
+/* State Ram Word 4 */
+#define ENETDMA_SRAM4_REG(x)		(0x20c + (x) * 0x10)
+
+/* Broadcom 6345 ENET DMA definitions */
+#define ENETDMA_6345_CHANCFG_REG	(0x00)
+
+#define ENETDMA_6345_MAXBURST_REG	(0x04)
+
+#define ENETDMA_6345_RSTART_REG		(0x08)
+
+#define ENETDMA_6345_LEN_REG		(0x0C)
+
+#define ENETDMA_6345_IR_REG		(0x14)
+
+#define ENETDMA_6345_IRMASK_REG		(0x18)
+
+#define ENETDMA_6345_FC_REG		(0x1C)
+
+#define ENETDMA_6345_BUFALLOC_REG	(0x20)
+
+/* Shift down for EOP, SOP and WRAP bits */
+#define ENETDMA_6345_DESC_SHIFT		(3)
+
+/*************************************************************************
+ * _REG relative to RSET_ENETDMAC
+ *************************************************************************/
+
+/* Channel Configuration register */
+#define ENETDMAC_CHANCFG_REG		(0x0)
+#define ENETDMAC_CHANCFG_EN_SHIFT	0
+#define ENETDMAC_CHANCFG_EN_MASK	(1 << ENETDMAC_CHANCFG_EN_SHIFT)
+#define ENETDMAC_CHANCFG_PKTHALT_SHIFT	1
+#define ENETDMAC_CHANCFG_PKTHALT_MASK	(1 << ENETDMAC_CHANCFG_PKTHALT_SHIFT)
+#define ENETDMAC_CHANCFG_BUFHALT_SHIFT	2
+#define ENETDMAC_CHANCFG_BUFHALT_MASK	(1 << ENETDMAC_CHANCFG_BUFHALT_SHIFT)
+#define ENETDMAC_CHANCFG_CHAINING_SHIFT	2
+#define ENETDMAC_CHANCFG_CHAINING_MASK	(1 << ENETDMAC_CHANCFG_CHAINING_SHIFT)
+#define ENETDMAC_CHANCFG_WRAP_EN_SHIFT	3
+#define ENETDMAC_CHANCFG_WRAP_EN_MASK	(1 << ENETDMAC_CHANCFG_WRAP_EN_SHIFT)
+#define ENETDMAC_CHANCFG_FLOWC_EN_SHIFT	4
+#define ENETDMAC_CHANCFG_FLOWC_EN_MASK	(1 << ENETDMAC_CHANCFG_FLOWC_EN_SHIFT)
+
+/* Interrupt Control/Status register */
+#define ENETDMAC_IR_REG			(0x4)
+#define ENETDMAC_IR_BUFDONE_MASK	(1 << 0)
+#define ENETDMAC_IR_PKTDONE_MASK	(1 << 1)
+#define ENETDMAC_IR_NOTOWNER_MASK	(1 << 2)
+
+/* Interrupt Mask register */
+#define ENETDMAC_IRMASK_REG		(0x8)
+
+/* Maximum Burst Length */
+#define ENETDMAC_MAXBURST_REG		(0xc)
+
+
+/*************************************************************************
+ * _REG relative to RSET_ENETDMAS
+ *************************************************************************/
+
+/* Ring Start Address register */
+#define ENETDMAS_RSTART_REG		(0x0)
+
+/* State Ram Word 2 */
+#define ENETDMAS_SRAM2_REG		(0x4)
+
+/* State Ram Word 3 */
+#define ENETDMAS_SRAM3_REG		(0x8)
+
+/* State Ram Word 4 */
+#define ENETDMAS_SRAM4_REG		(0xc)
+
+
+/*************************************************************************
+ * _REG relative to RSET_ENETSW
+ *************************************************************************/
+
+/* Port traffic control */
+#define ENETSW_PTCTRL_REG(x)		(0x0 + (x))
+#define ENETSW_PTCTRL_RXDIS_MASK	(1 << 0)
+#define ENETSW_PTCTRL_TXDIS_MASK	(1 << 1)
+
+/* Switch mode register */
+#define ENETSW_SWMODE_REG		(0xb)
+#define ENETSW_SWMODE_FWD_EN_MASK	(1 << 1)
+
+/* IMP override Register */
+#define ENETSW_IMPOV_REG		(0xe)
+#define ENETSW_IMPOV_FORCE_MASK		(1 << 7)
+#define ENETSW_IMPOV_TXFLOW_MASK	(1 << 5)
+#define ENETSW_IMPOV_RXFLOW_MASK	(1 << 4)
+#define ENETSW_IMPOV_1000_MASK		(1 << 3)
+#define ENETSW_IMPOV_100_MASK		(1 << 2)
+#define ENETSW_IMPOV_FDX_MASK		(1 << 1)
+#define ENETSW_IMPOV_LINKUP_MASK	(1 << 0)
+
+/* Port override Register */
+#define ENETSW_PORTOV_REG(x)		(0x58 + (x))
+#define ENETSW_PORTOV_ENABLE_MASK	(1 << 6)
+#define ENETSW_PORTOV_TXFLOW_MASK	(1 << 5)
+#define ENETSW_PORTOV_RXFLOW_MASK	(1 << 4)
+#define ENETSW_PORTOV_1000_MASK		(1 << 3)
+#define ENETSW_PORTOV_100_MASK		(1 << 2)
+#define ENETSW_PORTOV_FDX_MASK		(1 << 1)
+#define ENETSW_PORTOV_LINKUP_MASK	(1 << 0)
+
+/* MDIO control register */
+#define ENETSW_MDIOC_REG		(0xb0)
+#define ENETSW_MDIOC_EXT_MASK		(1 << 16)
+#define ENETSW_MDIOC_REG_SHIFT		20
+#define ENETSW_MDIOC_PHYID_SHIFT	25
+#define ENETSW_MDIOC_RD_MASK		(1 << 30)
+#define ENETSW_MDIOC_WR_MASK		(1 << 31)
+
+/* MDIO data register */
+#define ENETSW_MDIOD_REG		(0xb4)
+
+/* Global Management Configuration Register */
+#define ENETSW_GMCR_REG			(0x200)
+#define ENETSW_GMCR_RST_MIB_MASK	(1 << 0)
+
+/* MIB register */
+#define ENETSW_MIB_REG(x)		(0x2800 + (x) * 4)
+#define ENETSW_MIB_REG_COUNT		47
+
+/* Jumbo control register port mask register */
+#define ENETSW_JMBCTL_PORT_REG		(0x4004)
+
+/* Jumbo control mib good frame register */
+#define ENETSW_JMBCTL_MAXSIZE_REG	(0x4008)
+
+
+/*************************************************************************
+ * _REG relative to RSET_OHCI_PRIV
+ *************************************************************************/
+
+#define OHCI_PRIV_REG			0x0
+#define OHCI_PRIV_PORT1_HOST_SHIFT	0
+#define OHCI_PRIV_PORT1_HOST_MASK	(1 << OHCI_PRIV_PORT1_HOST_SHIFT)
+#define OHCI_PRIV_REG_SWAP_SHIFT	3
+#define OHCI_PRIV_REG_SWAP_MASK		(1 << OHCI_PRIV_REG_SWAP_SHIFT)
+
+
+/*************************************************************************
+ * _REG relative to RSET_USBH_PRIV
+ *************************************************************************/
+
+#define USBH_PRIV_SWAP_6358_REG		0x0
+#define USBH_PRIV_SWAP_6368_REG		0x1c
+
+#define USBH_PRIV_SWAP_USBD_SHIFT	6
+#define USBH_PRIV_SWAP_USBD_MASK	(1 << USBH_PRIV_SWAP_USBD_SHIFT)
+#define USBH_PRIV_SWAP_EHCI_ENDN_SHIFT	4
+#define USBH_PRIV_SWAP_EHCI_ENDN_MASK	(1 << USBH_PRIV_SWAP_EHCI_ENDN_SHIFT)
+#define USBH_PRIV_SWAP_EHCI_DATA_SHIFT	3
+#define USBH_PRIV_SWAP_EHCI_DATA_MASK	(1 << USBH_PRIV_SWAP_EHCI_DATA_SHIFT)
+#define USBH_PRIV_SWAP_OHCI_ENDN_SHIFT	1
+#define USBH_PRIV_SWAP_OHCI_ENDN_MASK	(1 << USBH_PRIV_SWAP_OHCI_ENDN_SHIFT)
+#define USBH_PRIV_SWAP_OHCI_DATA_SHIFT	0
+#define USBH_PRIV_SWAP_OHCI_DATA_MASK	(1 << USBH_PRIV_SWAP_OHCI_DATA_SHIFT)
+
+#define USBH_PRIV_UTMI_CTL_6368_REG	0x10
+#define USBH_PRIV_UTMI_CTL_NODRIV_SHIFT 12
+#define USBH_PRIV_UTMI_CTL_NODRIV_MASK	(0xf << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT)
+#define USBH_PRIV_UTMI_CTL_HOSTB_SHIFT	0
+#define USBH_PRIV_UTMI_CTL_HOSTB_MASK	(0xf << USBH_PRIV_UTMI_CTL_HOSTB_SHIFT)
+
+#define USBH_PRIV_TEST_6358_REG		0x24
+#define USBH_PRIV_TEST_6368_REG		0x14
+
+#define USBH_PRIV_SETUP_6368_REG	0x28
+#define USBH_PRIV_SETUP_IOC_SHIFT	4
+#define USBH_PRIV_SETUP_IOC_MASK	(1 << USBH_PRIV_SETUP_IOC_SHIFT)
+
+
+/*************************************************************************
+ * _REG relative to RSET_USBD
+ *************************************************************************/
+
+/* General control */
+#define USBD_CONTROL_REG		0x00
+#define USBD_CONTROL_TXZLENINS_SHIFT	14
+#define USBD_CONTROL_TXZLENINS_MASK	(1 << USBD_CONTROL_TXZLENINS_SHIFT)
+#define USBD_CONTROL_AUTO_CSRS_SHIFT	13
+#define USBD_CONTROL_AUTO_CSRS_MASK	(1 << USBD_CONTROL_AUTO_CSRS_SHIFT)
+#define USBD_CONTROL_RXZSCFG_SHIFT	12
+#define USBD_CONTROL_RXZSCFG_MASK	(1 << USBD_CONTROL_RXZSCFG_SHIFT)
+#define USBD_CONTROL_INIT_SEL_SHIFT	8
+#define USBD_CONTROL_INIT_SEL_MASK	(0xf << USBD_CONTROL_INIT_SEL_SHIFT)
+#define USBD_CONTROL_FIFO_RESET_SHIFT	6
+#define USBD_CONTROL_FIFO_RESET_MASK	(3 << USBD_CONTROL_FIFO_RESET_SHIFT)
+#define USBD_CONTROL_SETUPERRLOCK_SHIFT 5
+#define USBD_CONTROL_SETUPERRLOCK_MASK	(1 << USBD_CONTROL_SETUPERRLOCK_SHIFT)
+#define USBD_CONTROL_DONE_CSRS_SHIFT	0
+#define USBD_CONTROL_DONE_CSRS_MASK	(1 << USBD_CONTROL_DONE_CSRS_SHIFT)
+
+/* Strap options */
+#define USBD_STRAPS_REG			0x04
+#define USBD_STRAPS_APP_SELF_PWR_SHIFT	10
+#define USBD_STRAPS_APP_SELF_PWR_MASK	(1 << USBD_STRAPS_APP_SELF_PWR_SHIFT)
+#define USBD_STRAPS_APP_DISCON_SHIFT	9
+#define USBD_STRAPS_APP_DISCON_MASK	(1 << USBD_STRAPS_APP_DISCON_SHIFT)
+#define USBD_STRAPS_APP_CSRPRGSUP_SHIFT 8
+#define USBD_STRAPS_APP_CSRPRGSUP_MASK	(1 << USBD_STRAPS_APP_CSRPRGSUP_SHIFT)
+#define USBD_STRAPS_APP_RMTWKUP_SHIFT	6
+#define USBD_STRAPS_APP_RMTWKUP_MASK	(1 << USBD_STRAPS_APP_RMTWKUP_SHIFT)
+#define USBD_STRAPS_APP_RAM_IF_SHIFT	7
+#define USBD_STRAPS_APP_RAM_IF_MASK	(1 << USBD_STRAPS_APP_RAM_IF_SHIFT)
+#define USBD_STRAPS_APP_8BITPHY_SHIFT	2
+#define USBD_STRAPS_APP_8BITPHY_MASK	(1 << USBD_STRAPS_APP_8BITPHY_SHIFT)
+#define USBD_STRAPS_SPEED_SHIFT		0
+#define USBD_STRAPS_SPEED_MASK		(3 << USBD_STRAPS_SPEED_SHIFT)
+
+/* Stall control */
+#define USBD_STALL_REG			0x08
+#define USBD_STALL_UPDATE_SHIFT		7
+#define USBD_STALL_UPDATE_MASK		(1 << USBD_STALL_UPDATE_SHIFT)
+#define USBD_STALL_ENABLE_SHIFT		6
+#define USBD_STALL_ENABLE_MASK		(1 << USBD_STALL_ENABLE_SHIFT)
+#define USBD_STALL_EPNUM_SHIFT		0
+#define USBD_STALL_EPNUM_MASK		(0xf << USBD_STALL_EPNUM_SHIFT)
+
+/* General status */
+#define USBD_STATUS_REG			0x0c
+#define USBD_STATUS_SOF_SHIFT		16
+#define USBD_STATUS_SOF_MASK		(0x7ff << USBD_STATUS_SOF_SHIFT)
+#define USBD_STATUS_SPD_SHIFT		12
+#define USBD_STATUS_SPD_MASK		(3 << USBD_STATUS_SPD_SHIFT)
+#define USBD_STATUS_ALTINTF_SHIFT	8
+#define USBD_STATUS_ALTINTF_MASK	(0xf << USBD_STATUS_ALTINTF_SHIFT)
+#define USBD_STATUS_INTF_SHIFT		4
+#define USBD_STATUS_INTF_MASK		(0xf << USBD_STATUS_INTF_SHIFT)
+#define USBD_STATUS_CFG_SHIFT		0
+#define USBD_STATUS_CFG_MASK		(0xf << USBD_STATUS_CFG_SHIFT)
+
+/* Other events */
+#define USBD_EVENTS_REG			0x10
+#define USBD_EVENTS_USB_LINK_SHIFT	10
+#define USBD_EVENTS_USB_LINK_MASK	(1 << USBD_EVENTS_USB_LINK_SHIFT)
+
+/* IRQ status */
+#define USBD_EVENT_IRQ_STATUS_REG	0x14
+
+/* IRQ level (2 bits per IRQ event) */
+#define USBD_EVENT_IRQ_CFG_HI_REG	0x18
+
+#define USBD_EVENT_IRQ_CFG_LO_REG	0x1c
+
+#define USBD_EVENT_IRQ_CFG_SHIFT(x)	((x & 0xf) << 1)
+#define USBD_EVENT_IRQ_CFG_MASK(x)	(3 << USBD_EVENT_IRQ_CFG_SHIFT(x))
+#define USBD_EVENT_IRQ_CFG_RISING(x)	(0 << USBD_EVENT_IRQ_CFG_SHIFT(x))
+#define USBD_EVENT_IRQ_CFG_FALLING(x)	(1 << USBD_EVENT_IRQ_CFG_SHIFT(x))
+
+/* IRQ mask (1=unmasked) */
+#define USBD_EVENT_IRQ_MASK_REG		0x20
+
+/* IRQ bits */
+#define USBD_EVENT_IRQ_USB_LINK		10
+#define USBD_EVENT_IRQ_SETCFG		9
+#define USBD_EVENT_IRQ_SETINTF		8
+#define USBD_EVENT_IRQ_ERRATIC_ERR	7
+#define USBD_EVENT_IRQ_SET_CSRS		6
+#define USBD_EVENT_IRQ_SUSPEND		5
+#define USBD_EVENT_IRQ_EARLY_SUSPEND	4
+#define USBD_EVENT_IRQ_SOF		3
+#define USBD_EVENT_IRQ_ENUM_ON		2
+#define USBD_EVENT_IRQ_SETUP		1
+#define USBD_EVENT_IRQ_USB_RESET	0
+
+/* TX FIFO partitioning */
+#define USBD_TXFIFO_CONFIG_REG		0x40
+#define USBD_TXFIFO_CONFIG_END_SHIFT	16
+#define USBD_TXFIFO_CONFIG_END_MASK	(0xff << USBD_TXFIFO_CONFIG_END_SHIFT)
+#define USBD_TXFIFO_CONFIG_START_SHIFT	0
+#define USBD_TXFIFO_CONFIG_START_MASK	(0xff << USBD_TXFIFO_CONFIG_START_SHIFT)
+
+/* RX FIFO partitioning */
+#define USBD_RXFIFO_CONFIG_REG		0x44
+#define USBD_RXFIFO_CONFIG_END_SHIFT	16
+#define USBD_RXFIFO_CONFIG_END_MASK	(0xff << USBD_TXFIFO_CONFIG_END_SHIFT)
+#define USBD_RXFIFO_CONFIG_START_SHIFT	0
+#define USBD_RXFIFO_CONFIG_START_MASK	(0xff << USBD_TXFIFO_CONFIG_START_SHIFT)
+
+/* TX FIFO/endpoint configuration */
+#define USBD_TXFIFO_EPSIZE_REG		0x48
+
+/* RX FIFO/endpoint configuration */
+#define USBD_RXFIFO_EPSIZE_REG		0x4c
+
+/* Endpoint<->DMA mappings */
+#define USBD_EPNUM_TYPEMAP_REG		0x50
+#define USBD_EPNUM_TYPEMAP_TYPE_SHIFT	8
+#define USBD_EPNUM_TYPEMAP_TYPE_MASK	(0x3 << USBD_EPNUM_TYPEMAP_TYPE_SHIFT)
+#define USBD_EPNUM_TYPEMAP_DMA_CH_SHIFT 0
+#define USBD_EPNUM_TYPEMAP_DMA_CH_MASK	(0xf << USBD_EPNUM_TYPEMAP_DMACH_SHIFT)
+
+/* Misc per-endpoint settings */
+#define USBD_CSR_SETUPADDR_REG		0x80
+#define USBD_CSR_SETUPADDR_DEF		0xb550
+
+#define USBD_CSR_EP_REG(x)		(0x84 + (x) * 4)
+#define USBD_CSR_EP_MAXPKT_SHIFT	19
+#define USBD_CSR_EP_MAXPKT_MASK		(0x7ff << USBD_CSR_EP_MAXPKT_SHIFT)
+#define USBD_CSR_EP_ALTIFACE_SHIFT	15
+#define USBD_CSR_EP_ALTIFACE_MASK	(0xf << USBD_CSR_EP_ALTIFACE_SHIFT)
+#define USBD_CSR_EP_IFACE_SHIFT		11
+#define USBD_CSR_EP_IFACE_MASK		(0xf << USBD_CSR_EP_IFACE_SHIFT)
+#define USBD_CSR_EP_CFG_SHIFT		7
+#define USBD_CSR_EP_CFG_MASK		(0xf << USBD_CSR_EP_CFG_SHIFT)
+#define USBD_CSR_EP_TYPE_SHIFT		5
+#define USBD_CSR_EP_TYPE_MASK		(3 << USBD_CSR_EP_TYPE_SHIFT)
+#define USBD_CSR_EP_DIR_SHIFT		4
+#define USBD_CSR_EP_DIR_MASK		(1 << USBD_CSR_EP_DIR_SHIFT)
+#define USBD_CSR_EP_LOG_SHIFT		0
+#define USBD_CSR_EP_LOG_MASK		(0xf << USBD_CSR_EP_LOG_SHIFT)
+
+
+/*************************************************************************
+ * _REG relative to RSET_MPI
+ *************************************************************************/
+
+/* well known (hard wired) chip select */
+#define MPI_CS_PCMCIA_COMMON		4
+#define MPI_CS_PCMCIA_ATTR		5
+#define MPI_CS_PCMCIA_IO		6
+
+/* Chip select base register */
+#define MPI_CSBASE_REG(x)		(0x0 + (x) * 8)
+#define MPI_CSBASE_BASE_SHIFT		13
+#define MPI_CSBASE_BASE_MASK		(0x1ffff << MPI_CSBASE_BASE_SHIFT)
+#define MPI_CSBASE_SIZE_SHIFT		0
+#define MPI_CSBASE_SIZE_MASK		(0xf << MPI_CSBASE_SIZE_SHIFT)
+
+#define MPI_CSBASE_SIZE_8K		0
+#define MPI_CSBASE_SIZE_16K		1
+#define MPI_CSBASE_SIZE_32K		2
+#define MPI_CSBASE_SIZE_64K		3
+#define MPI_CSBASE_SIZE_128K		4
+#define MPI_CSBASE_SIZE_256K		5
+#define MPI_CSBASE_SIZE_512K		6
+#define MPI_CSBASE_SIZE_1M		7
+#define MPI_CSBASE_SIZE_2M		8
+#define MPI_CSBASE_SIZE_4M		9
+#define MPI_CSBASE_SIZE_8M		10
+#define MPI_CSBASE_SIZE_16M		11
+#define MPI_CSBASE_SIZE_32M		12
+#define MPI_CSBASE_SIZE_64M		13
+#define MPI_CSBASE_SIZE_128M		14
+#define MPI_CSBASE_SIZE_256M		15
+
+/* Chip select control register */
+#define MPI_CSCTL_REG(x)		(0x4 + (x) * 8)
+#define MPI_CSCTL_ENABLE_MASK		(1 << 0)
+#define MPI_CSCTL_WAIT_SHIFT		1
+#define MPI_CSCTL_WAIT_MASK		(0x7 << MPI_CSCTL_WAIT_SHIFT)
+#define MPI_CSCTL_DATA16_MASK		(1 << 4)
+#define MPI_CSCTL_SYNCMODE_MASK		(1 << 7)
+#define MPI_CSCTL_TSIZE_MASK		(1 << 8)
+#define MPI_CSCTL_ENDIANSWAP_MASK	(1 << 10)
+#define MPI_CSCTL_SETUP_SHIFT		16
+#define MPI_CSCTL_SETUP_MASK		(0xf << MPI_CSCTL_SETUP_SHIFT)
+#define MPI_CSCTL_HOLD_SHIFT		20
+#define MPI_CSCTL_HOLD_MASK		(0xf << MPI_CSCTL_HOLD_SHIFT)
+
+/* PCI registers */
+#define MPI_SP0_RANGE_REG		0x100
+#define MPI_SP0_REMAP_REG		0x104
+#define MPI_SP0_REMAP_ENABLE_MASK	(1 << 0)
+#define MPI_SP1_RANGE_REG		0x10C
+#define MPI_SP1_REMAP_REG		0x110
+#define MPI_SP1_REMAP_ENABLE_MASK	(1 << 0)
+
+#define MPI_L2PCFG_REG			0x11C
+#define MPI_L2PCFG_CFG_TYPE_SHIFT	0
+#define MPI_L2PCFG_CFG_TYPE_MASK	(0x3 << MPI_L2PCFG_CFG_TYPE_SHIFT)
+#define MPI_L2PCFG_REG_SHIFT		2
+#define MPI_L2PCFG_REG_MASK		(0x3f << MPI_L2PCFG_REG_SHIFT)
+#define MPI_L2PCFG_FUNC_SHIFT		8
+#define MPI_L2PCFG_FUNC_MASK		(0x7 << MPI_L2PCFG_FUNC_SHIFT)
+#define MPI_L2PCFG_DEVNUM_SHIFT		11
+#define MPI_L2PCFG_DEVNUM_MASK		(0x1f << MPI_L2PCFG_DEVNUM_SHIFT)
+#define MPI_L2PCFG_CFG_USEREG_MASK	(1 << 30)
+#define MPI_L2PCFG_CFG_SEL_MASK		(1 << 31)
+
+#define MPI_L2PMEMRANGE1_REG		0x120
+#define MPI_L2PMEMBASE1_REG		0x124
+#define MPI_L2PMEMREMAP1_REG		0x128
+#define MPI_L2PMEMRANGE2_REG		0x12C
+#define MPI_L2PMEMBASE2_REG		0x130
+#define MPI_L2PMEMREMAP2_REG		0x134
+#define MPI_L2PIORANGE_REG		0x138
+#define MPI_L2PIOBASE_REG		0x13C
+#define MPI_L2PIOREMAP_REG		0x140
+#define MPI_L2P_BASE_MASK		(0xffff8000)
+#define MPI_L2PREMAP_ENABLED_MASK	(1 << 0)
+#define MPI_L2PREMAP_IS_CARDBUS_MASK	(1 << 2)
+
+#define MPI_PCIMODESEL_REG		0x144
+#define MPI_PCIMODESEL_BAR1_NOSWAP_MASK (1 << 0)
+#define MPI_PCIMODESEL_BAR2_NOSWAP_MASK (1 << 1)
+#define MPI_PCIMODESEL_EXT_ARB_MASK	(1 << 2)
+#define MPI_PCIMODESEL_PREFETCH_SHIFT	4
+#define MPI_PCIMODESEL_PREFETCH_MASK	(0xf << MPI_PCIMODESEL_PREFETCH_SHIFT)
+
+#define MPI_LOCBUSCTL_REG		0x14C
+#define MPI_LOCBUSCTL_EN_PCI_GPIO_MASK	(1 << 0)
+#define MPI_LOCBUSCTL_U2P_NOSWAP_MASK	(1 << 1)
+
+#define MPI_LOCINT_REG			0x150
+#define MPI_LOCINT_MASK(x)		(1 << (x + 16))
+#define MPI_LOCINT_STAT(x)		(1 << (x))
+#define MPI_LOCINT_DIR_FAILED		6
+#define MPI_LOCINT_EXT_PCI_INT		7
+#define MPI_LOCINT_SERR			8
+#define MPI_LOCINT_CSERR		9
+
+#define MPI_PCICFGCTL_REG		0x178
+#define MPI_PCICFGCTL_CFGADDR_SHIFT	2
+#define MPI_PCICFGCTL_CFGADDR_MASK	(0x1f << MPI_PCICFGCTL_CFGADDR_SHIFT)
+#define MPI_PCICFGCTL_WRITEEN_MASK	(1 << 7)
+
+#define MPI_PCICFGDATA_REG		0x17C
+
+/* PCI host bridge custom register */
+#define BCMPCI_REG_TIMERS		0x40
+#define REG_TIMER_TRDY_SHIFT		0
+#define REG_TIMER_TRDY_MASK		(0xff << REG_TIMER_TRDY_SHIFT)
+#define REG_TIMER_RETRY_SHIFT		8
+#define REG_TIMER_RETRY_MASK		(0xff << REG_TIMER_RETRY_SHIFT)
+
+
+/*************************************************************************
+ * _REG relative to RSET_PCMCIA
+ *************************************************************************/
+
+#define PCMCIA_C1_REG			0x0
+#define PCMCIA_C1_CD1_MASK		(1 << 0)
+#define PCMCIA_C1_CD2_MASK		(1 << 1)
+#define PCMCIA_C1_VS1_MASK		(1 << 2)
+#define PCMCIA_C1_VS2_MASK		(1 << 3)
+#define PCMCIA_C1_VS1OE_MASK		(1 << 6)
+#define PCMCIA_C1_VS2OE_MASK		(1 << 7)
+#define PCMCIA_C1_CBIDSEL_SHIFT		(8)
+#define PCMCIA_C1_CBIDSEL_MASK		(0x1f << PCMCIA_C1_CBIDSEL_SHIFT)
+#define PCMCIA_C1_EN_PCMCIA_GPIO_MASK	(1 << 13)
+#define PCMCIA_C1_EN_PCMCIA_MASK	(1 << 14)
+#define PCMCIA_C1_EN_CARDBUS_MASK	(1 << 15)
+#define PCMCIA_C1_RESET_MASK		(1 << 18)
+
+#define PCMCIA_C2_REG			0x8
+#define PCMCIA_C2_DATA16_MASK		(1 << 0)
+#define PCMCIA_C2_BYTESWAP_MASK		(1 << 1)
+#define PCMCIA_C2_RWCOUNT_SHIFT		2
+#define PCMCIA_C2_RWCOUNT_MASK		(0x3f << PCMCIA_C2_RWCOUNT_SHIFT)
+#define PCMCIA_C2_INACTIVE_SHIFT	8
+#define PCMCIA_C2_INACTIVE_MASK		(0x3f << PCMCIA_C2_INACTIVE_SHIFT)
+#define PCMCIA_C2_SETUP_SHIFT		16
+#define PCMCIA_C2_SETUP_MASK		(0x3f << PCMCIA_C2_SETUP_SHIFT)
+#define PCMCIA_C2_HOLD_SHIFT		24
+#define PCMCIA_C2_HOLD_MASK		(0x3f << PCMCIA_C2_HOLD_SHIFT)
+
+
+/*************************************************************************
+ * _REG relative to RSET_SDRAM
+ *************************************************************************/
+
+#define SDRAM_CFG_REG			0x0
+#define SDRAM_CFG_ROW_SHIFT		4
+#define SDRAM_CFG_ROW_MASK		(0x3 << SDRAM_CFG_ROW_SHIFT)
+#define SDRAM_CFG_COL_SHIFT		6
+#define SDRAM_CFG_COL_MASK		(0x3 << SDRAM_CFG_COL_SHIFT)
+#define SDRAM_CFG_32B_SHIFT		10
+#define SDRAM_CFG_32B_MASK		(1 << SDRAM_CFG_32B_SHIFT)
+#define SDRAM_CFG_BANK_SHIFT		13
+#define SDRAM_CFG_BANK_MASK		(1 << SDRAM_CFG_BANK_SHIFT)
+
+#define SDRAM_MBASE_REG			0xc
+
+#define SDRAM_PRIO_REG			0x2C
+#define SDRAM_PRIO_MIPS_SHIFT		29
+#define SDRAM_PRIO_MIPS_MASK		(1 << SDRAM_PRIO_MIPS_SHIFT)
+#define SDRAM_PRIO_ADSL_SHIFT		30
+#define SDRAM_PRIO_ADSL_MASK		(1 << SDRAM_PRIO_ADSL_SHIFT)
+#define SDRAM_PRIO_EN_SHIFT		31
+#define SDRAM_PRIO_EN_MASK		(1 << SDRAM_PRIO_EN_SHIFT)
+
+
+/*************************************************************************
+ * _REG relative to RSET_MEMC
+ *************************************************************************/
+
+#define MEMC_CFG_REG			0x4
+#define MEMC_CFG_32B_SHIFT		1
+#define MEMC_CFG_32B_MASK		(1 << MEMC_CFG_32B_SHIFT)
+#define MEMC_CFG_COL_SHIFT		3
+#define MEMC_CFG_COL_MASK		(0x3 << MEMC_CFG_COL_SHIFT)
+#define MEMC_CFG_ROW_SHIFT		6
+#define MEMC_CFG_ROW_MASK		(0x3 << MEMC_CFG_ROW_SHIFT)
+
+
+/*************************************************************************
+ * _REG relative to RSET_DDR
+ *************************************************************************/
+
+#define DDR_CSEND_REG			0x8
+
+#define DDR_DMIPSPLLCFG_REG		0x18
+#define DMIPSPLLCFG_M1_SHIFT		0
+#define DMIPSPLLCFG_M1_MASK		(0xff << DMIPSPLLCFG_M1_SHIFT)
+#define DMIPSPLLCFG_N1_SHIFT		23
+#define DMIPSPLLCFG_N1_MASK		(0x3f << DMIPSPLLCFG_N1_SHIFT)
+#define DMIPSPLLCFG_N2_SHIFT		29
+#define DMIPSPLLCFG_N2_MASK		(0x7 << DMIPSPLLCFG_N2_SHIFT)
+
+#define DDR_DMIPSPLLCFG_6368_REG	0x20
+#define DMIPSPLLCFG_6368_P1_SHIFT	0
+#define DMIPSPLLCFG_6368_P1_MASK	(0xf << DMIPSPLLCFG_6368_P1_SHIFT)
+#define DMIPSPLLCFG_6368_P2_SHIFT	4
+#define DMIPSPLLCFG_6368_P2_MASK	(0xf << DMIPSPLLCFG_6368_P2_SHIFT)
+#define DMIPSPLLCFG_6368_NDIV_SHIFT	16
+#define DMIPSPLLCFG_6368_NDIV_MASK	(0x1ff << DMIPSPLLCFG_6368_NDIV_SHIFT)
+
+#define DDR_DMIPSPLLDIV_6368_REG	0x24
+#define DMIPSPLLDIV_6368_MDIV_SHIFT	0
+#define DMIPSPLLDIV_6368_MDIV_MASK	(0xff << DMIPSPLLDIV_6368_MDIV_SHIFT)
+
+
+/*************************************************************************
+ * _REG relative to RSET_M2M
+ *************************************************************************/
+
+#define M2M_RX				0
+#define M2M_TX				1
+
+#define M2M_SRC_REG(x)			((x) * 0x40 + 0x00)
+#define M2M_DST_REG(x)			((x) * 0x40 + 0x04)
+#define M2M_SIZE_REG(x)			((x) * 0x40 + 0x08)
+
+#define M2M_CTRL_REG(x)			((x) * 0x40 + 0x0c)
+#define M2M_CTRL_ENABLE_MASK		(1 << 0)
+#define M2M_CTRL_IRQEN_MASK		(1 << 1)
+#define M2M_CTRL_ERROR_CLR_MASK		(1 << 6)
+#define M2M_CTRL_DONE_CLR_MASK		(1 << 7)
+#define M2M_CTRL_NOINC_MASK		(1 << 8)
+#define M2M_CTRL_PCMCIASWAP_MASK	(1 << 9)
+#define M2M_CTRL_SWAPBYTE_MASK		(1 << 10)
+#define M2M_CTRL_ENDIAN_MASK		(1 << 11)
+
+#define M2M_STAT_REG(x)			((x) * 0x40 + 0x10)
+#define M2M_STAT_DONE			(1 << 0)
+#define M2M_STAT_ERROR			(1 << 1)
+
+#define M2M_SRCID_REG(x)		((x) * 0x40 + 0x14)
+#define M2M_DSTID_REG(x)		((x) * 0x40 + 0x18)
+
+/*************************************************************************
+ * _REG relative to RSET_SPI
+ *************************************************************************/
+
+/* BCM 6338/6348 SPI core */
+#define SPI_6348_CMD			0x00	/* 16-bits register */
+#define SPI_6348_INT_STATUS		0x02
+#define SPI_6348_INT_MASK_ST		0x03
+#define SPI_6348_INT_MASK		0x04
+#define SPI_6348_ST			0x05
+#define SPI_6348_CLK_CFG		0x06
+#define SPI_6348_FILL_BYTE		0x07
+#define SPI_6348_MSG_TAIL		0x09
+#define SPI_6348_RX_TAIL		0x0b
+#define SPI_6348_MSG_CTL		0x40	/* 8-bits register */
+#define SPI_6348_MSG_CTL_WIDTH		8
+#define SPI_6348_MSG_DATA		0x41
+#define SPI_6348_MSG_DATA_SIZE		0x3f
+#define SPI_6348_RX_DATA		0x80
+#define SPI_6348_RX_DATA_SIZE		0x3f
+
+/* BCM 3368/6358/6262/6368 SPI core */
+#define SPI_6358_MSG_CTL		0x00	/* 16-bits register */
+#define SPI_6358_MSG_CTL_WIDTH		16
+#define SPI_6358_MSG_DATA		0x02
+#define SPI_6358_MSG_DATA_SIZE		0x21e
+#define SPI_6358_RX_DATA		0x400
+#define SPI_6358_RX_DATA_SIZE		0x220
+#define SPI_6358_CMD			0x700	/* 16-bits register */
+#define SPI_6358_INT_STATUS		0x702
+#define SPI_6358_INT_MASK_ST		0x703
+#define SPI_6358_INT_MASK		0x704
+#define SPI_6358_ST			0x705
+#define SPI_6358_CLK_CFG		0x706
+#define SPI_6358_FILL_BYTE		0x707
+#define SPI_6358_MSG_TAIL		0x709
+#define SPI_6358_RX_TAIL		0x70B
+
+/* Shared SPI definitions */
+
+/* Message configuration */
+#define SPI_FD_RW			0x00
+#define SPI_HD_W			0x01
+#define SPI_HD_R			0x02
+#define SPI_BYTE_CNT_SHIFT		0
+#define SPI_6348_MSG_TYPE_SHIFT		6
+#define SPI_6358_MSG_TYPE_SHIFT		14
+
+/* Command */
+#define SPI_CMD_NOOP			0x00
+#define SPI_CMD_SOFT_RESET		0x01
+#define SPI_CMD_HARD_RESET		0x02
+#define SPI_CMD_START_IMMEDIATE		0x03
+#define SPI_CMD_COMMAND_SHIFT		0
+#define SPI_CMD_COMMAND_MASK		0x000f
+#define SPI_CMD_DEVICE_ID_SHIFT		4
+#define SPI_CMD_PREPEND_BYTE_CNT_SHIFT	8
+#define SPI_CMD_ONE_BYTE_SHIFT		11
+#define SPI_CMD_ONE_WIRE_SHIFT		12
+#define SPI_DEV_ID_0			0
+#define SPI_DEV_ID_1			1
+#define SPI_DEV_ID_2			2
+#define SPI_DEV_ID_3			3
+
+/* Interrupt mask */
+#define SPI_INTR_CMD_DONE		0x01
+#define SPI_INTR_RX_OVERFLOW		0x02
+#define SPI_INTR_TX_UNDERFLOW		0x04
+#define SPI_INTR_TX_OVERFLOW		0x08
+#define SPI_INTR_RX_UNDERFLOW		0x10
+#define SPI_INTR_CLEAR_ALL		0x1f
+
+/* Status */
+#define SPI_RX_EMPTY			0x02
+#define SPI_CMD_BUSY			0x04
+#define SPI_SERIAL_BUSY			0x08
+
+/* Clock configuration */
+#define SPI_CLK_20MHZ			0x00
+#define SPI_CLK_0_391MHZ		0x01
+#define SPI_CLK_0_781MHZ		0x02 /* default */
+#define SPI_CLK_1_563MHZ		0x03
+#define SPI_CLK_3_125MHZ		0x04
+#define SPI_CLK_6_250MHZ		0x05
+#define SPI_CLK_12_50MHZ		0x06
+#define SPI_CLK_MASK			0x07
+#define SPI_SSOFFTIME_MASK		0x38
+#define SPI_SSOFFTIME_SHIFT		3
+#define SPI_BYTE_SWAP			0x80
+
+/*************************************************************************
+ * _REG relative to RSET_MISC
+ *************************************************************************/
+#define MISC_SERDES_CTRL_6328_REG	0x0
+#define MISC_SERDES_CTRL_6362_REG	0x4
+#define SERDES_PCIE_EN			(1 << 0)
+#define SERDES_PCIE_EXD_EN		(1 << 15)
+
+#define MISC_STRAPBUS_6362_REG		0x14
+#define STRAPBUS_6362_FCVO_SHIFT	1
+#define STRAPBUS_6362_HSSPI_CLK_FAST	(1 << 13)
+#define STRAPBUS_6362_FCVO_MASK		(0x1f << STRAPBUS_6362_FCVO_SHIFT)
+#define STRAPBUS_6362_BOOT_SEL_SERIAL	(1 << 15)
+#define STRAPBUS_6362_BOOT_SEL_NAND	(0 << 15)
+
+#define MISC_STRAPBUS_6328_REG		0x240
+#define STRAPBUS_6328_FCVO_SHIFT	7
+#define STRAPBUS_6328_FCVO_MASK		(0x1f << STRAPBUS_6328_FCVO_SHIFT)
+#define STRAPBUS_6328_BOOT_SEL_SERIAL	(1 << 18)
+#define STRAPBUS_6328_BOOT_SEL_NAND	(0 << 18)
+
+/*************************************************************************
+ * _REG relative to RSET_PCIE
+ *************************************************************************/
+
+#define PCIE_CONFIG2_REG		0x408
+#define CONFIG2_BAR1_SIZE_EN		1
+#define CONFIG2_BAR1_SIZE_MASK		0xf
+
+#define PCIE_IDVAL3_REG			0x43c
+#define IDVAL3_CLASS_CODE_MASK		0xffffff
+
+#define PCIE_DLSTATUS_REG		0x1048
+#define DLSTATUS_PHYLINKUP		(1 << 13)
+
+#define PCIE_BRIDGE_OPT1_REG		0x2820
+#define OPT1_RD_BE_OPT_EN		(1 << 7)
+#define OPT1_RD_REPLY_BE_FIX_EN		(1 << 9)
+#define OPT1_PCIE_BRIDGE_HOLE_DET_EN	(1 << 11)
+#define OPT1_L1_INT_STATUS_MASK_POL	(1 << 12)
+
+#define PCIE_BRIDGE_OPT2_REG		0x2824
+#define OPT2_UBUS_UR_DECODE_DIS		(1 << 2)
+#define OPT2_TX_CREDIT_CHK_EN		(1 << 4)
+#define OPT2_CFG_TYPE1_BD_SEL		(1 << 7)
+#define OPT2_CFG_TYPE1_BUS_NO_SHIFT	16
+#define OPT2_CFG_TYPE1_BUS_NO_MASK	(0xff << OPT2_CFG_TYPE1_BUS_NO_SHIFT)
+
+#define PCIE_BRIDGE_BAR0_BASEMASK_REG	0x2828
+#define PCIE_BRIDGE_BAR1_BASEMASK_REG	0x2830
+#define BASEMASK_REMAP_EN		(1 << 0)
+#define BASEMASK_SWAP_EN		(1 << 1)
+#define BASEMASK_MASK_SHIFT		4
+#define BASEMASK_MASK_MASK		(0xfff << BASEMASK_MASK_SHIFT)
+#define BASEMASK_BASE_SHIFT		20
+#define BASEMASK_BASE_MASK		(0xfff << BASEMASK_BASE_SHIFT)
+
+#define PCIE_BRIDGE_BAR0_REBASE_ADDR_REG 0x282c
+#define PCIE_BRIDGE_BAR1_REBASE_ADDR_REG 0x2834
+#define REBASE_ADDR_BASE_SHIFT		20
+#define REBASE_ADDR_BASE_MASK		(0xfff << REBASE_ADDR_BASE_SHIFT)
+
+#define PCIE_BRIDGE_RC_INT_MASK_REG	0x2854
+#define PCIE_RC_INT_A			(1 << 0)
+#define PCIE_RC_INT_B			(1 << 1)
+#define PCIE_RC_INT_C			(1 << 2)
+#define PCIE_RC_INT_D			(1 << 3)
+
+#define PCIE_DEVICE_OFFSET		0x8000
+
+/*************************************************************************
+ * _REG relative to RSET_OTP
+ *************************************************************************/
+
+#define OTP_USER_BITS_6328_REG(i)	(0x20 + (i) * 4)
+#define   OTP_6328_REG3_TP1_DISABLED	BIT(9)
+
+#endif /* BCM63XX_REGS_H_ */
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_reset.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_reset.h
new file mode 100644
index 000000000..2c0645b7d
--- /dev/null
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_reset.h
@@ -0,0 +1,22 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __BCM63XX_RESET_H
+#define __BCM63XX_RESET_H
+
+enum bcm63xx_core_reset {
+	BCM63XX_RESET_SPI,
+	BCM63XX_RESET_ENET,
+	BCM63XX_RESET_USBH,
+	BCM63XX_RESET_USBD,
+	BCM63XX_RESET_SAR,
+	BCM63XX_RESET_DSL,
+	BCM63XX_RESET_EPHY,
+	BCM63XX_RESET_ENETSW,
+	BCM63XX_RESET_PCM,
+	BCM63XX_RESET_MPI,
+	BCM63XX_RESET_PCIE,
+	BCM63XX_RESET_PCIE_EXT,
+};
+
+void bcm63xx_core_set_reset(enum bcm63xx_core_reset, int reset);
+
+#endif
diff --git a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_timer.h b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_timer.h
new file mode 100644
index 000000000..bcbece793
--- /dev/null
+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_timer.h
@@ -0,0 +1,12 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef BCM63XX_TIMER_H_
+#define BCM63XX_TIMER_H_
+
+int bcm63xx_timer_register(int id, void (*callback)(void *data), void *data);
+void bcm63xx_timer_unregister(int id);
+int bcm63xx_timer_set(int id, int monotonic, unsigned int countdown_us);
+int bcm63xx_timer_enable(int id);
+int bcm63xx_timer_disable(int id);
+unsigned int bcm63xx_timer_countdown(unsigned int countdown_us);
+
+#endif /* !BCM63XX_TIMER_H_ */
diff --git a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
new file mode 100644
index 000000000..830f53f28
--- /dev/null
+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
@@ -0,0 +1,54 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef BOARD_BCM963XX_H_
+#define BOARD_BCM963XX_H_
+
+#include <linux/types.h>
+#include <linux/gpio.h>
+#include <linux/leds.h>
+#include <bcm63xx_dev_enet.h>
+#include <bcm63xx_dev_usb_usbd.h>
+
+/*
+ * flash mapping
+ */
+#define BCM963XX_CFE_VERSION_OFFSET	0x570
+#define BCM963XX_NVRAM_OFFSET		0x580
+
+/*
+ * board definition
+ */
+struct board_info {
+	u8		name[16];
+	unsigned int	expected_cpu_id;
+
+	/* enabled feature/device */
+	unsigned int	has_enet0:1;
+	unsigned int	has_enet1:1;
+	unsigned int	has_enetsw:1;
+	unsigned int	has_pci:1;
+	unsigned int	has_pccard:1;
+	unsigned int	has_ohci0:1;
+	unsigned int	has_ehci0:1;
+	unsigned int	has_usbd:1;
+	unsigned int	has_uart0:1;
+	unsigned int	has_uart1:1;
+
+	/* ethernet config */
+	struct bcm63xx_enet_platform_data enet0;
+	struct bcm63xx_enet_platform_data enet1;
+	struct bcm63xx_enetsw_platform_data enetsw;
+
+	/* USB config */
+	struct bcm63xx_usbd_platform_data usbd;
+
+	/* GPIO LEDs */
+	struct gpio_led leds[5];
+
+	/* External PHY reset GPIO */
+	unsigned int ephy_reset_gpio;
+
+	/* External PHY reset GPIO flags from gpio.h */
+	unsigned long ephy_reset_gpio_flags;
+};
+
+#endif /* ! BOARD_BCM963XX_H_ */
diff --git a/arch/mips/include/asm/mach-bcm63xx/cpu-feature-overrides.h b/arch/mips/include/asm/mach-bcm63xx/cpu-feature-overrides.h
new file mode 100644
index 000000000..0ebecbdb9
--- /dev/null
+++ b/arch/mips/include/asm/mach-bcm63xx/cpu-feature-overrides.h
@@ -0,0 +1,54 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_MACH_BCM963XX_CPU_FEATURE_OVERRIDES_H
+#define __ASM_MACH_BCM963XX_CPU_FEATURE_OVERRIDES_H
+
+#include <bcm63xx_cpu.h>
+
+#define cpu_has_tlb			1
+#define cpu_has_4kex			1
+#define cpu_has_4k_cache		1
+#define cpu_has_fpu			0
+#define cpu_has_32fpr			0
+#define cpu_has_counter			1
+#define cpu_has_watch			0
+#define cpu_has_divec			1
+#define cpu_has_vce			0
+#define cpu_has_cache_cdex_p		0
+#define cpu_has_cache_cdex_s		0
+#define cpu_has_prefetch		1
+#define cpu_has_mcheck			1
+#define cpu_has_ejtag			1
+#define cpu_has_llsc			1
+#define cpu_has_mips16			0
+#define cpu_has_mips16e2		0
+#define cpu_has_mdmx			0
+#define cpu_has_mips3d			0
+#define cpu_has_smartmips		0
+#define cpu_has_vtag_icache		0
+
+#if !defined(CONFIG_SYS_HAS_CPU_BMIPS4350)
+#define cpu_has_dc_aliases		0
+#endif
+
+#define cpu_has_ic_fills_f_dc		0
+#define cpu_has_pindexed_dcache		0
+
+#define cpu_has_mips32r1		1
+#define cpu_has_mips32r2		0
+#define cpu_has_mips64r1		0
+#define cpu_has_mips64r2		0
+
+#define cpu_has_dsp			0
+#define cpu_has_dsp2			0
+#define cpu_has_mipsmt			0
+#define cpu_has_userlocal		0
+
+#define cpu_has_nofpuex			0
+#define cpu_has_64bits			0
+#define cpu_has_64bit_zero_reg		0
+
+#define cpu_dcache_line_size()		16
+#define cpu_icache_line_size()		16
+#define cpu_scache_line_size()		0
+
+#endif /* __ASM_MACH_BCM963XX_CPU_FEATURE_OVERRIDES_H */
diff --git a/arch/mips/include/asm/mach-bcm63xx/ioremap.h b/arch/mips/include/asm/mach-bcm63xx/ioremap.h
new file mode 100644
index 000000000..73f31825b
--- /dev/null
+++ b/arch/mips/include/asm/mach-bcm63xx/ioremap.h
@@ -0,0 +1,44 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef BCM63XX_IOREMAP_H_
+#define BCM63XX_IOREMAP_H_
+
+#include <bcm63xx_cpu.h>
+
+static inline int is_bcm63xx_internal_registers(phys_addr_t offset)
+{
+	switch (bcm63xx_get_cpu_id()) {
+	case BCM3368_CPU_ID:
+		if (offset >= 0xfff80000)
+			return 1;
+		break;
+	case BCM6338_CPU_ID:
+	case BCM6345_CPU_ID:
+	case BCM6348_CPU_ID:
+	case BCM6358_CPU_ID:
+		if (offset >= 0xfff00000)
+			return 1;
+		break;
+	case BCM6328_CPU_ID:
+	case BCM6362_CPU_ID:
+	case BCM6368_CPU_ID:
+		if (offset >= 0xb0000000 && offset < 0xb1000000)
+			return 1;
+		break;
+	}
+	return 0;
+}
+
+static inline void __iomem *plat_ioremap(phys_addr_t offset, unsigned long size,
+					 unsigned long flags)
+{
+	if (is_bcm63xx_internal_registers(offset))
+		return (void __iomem *)offset;
+	return NULL;
+}
+
+static inline int plat_iounmap(const volatile void __iomem *addr)
+{
+	return is_bcm63xx_internal_registers((unsigned long)addr);
+}
+
+#endif /* BCM63XX_IOREMAP_H_ */
diff --git a/arch/mips/include/asm/mach-bcm63xx/irq.h b/arch/mips/include/asm/mach-bcm63xx/irq.h
new file mode 100644
index 000000000..b016f0615
--- /dev/null
+++ b/arch/mips/include/asm/mach-bcm63xx/irq.h
@@ -0,0 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_MACH_BCM63XX_IRQ_H
+#define __ASM_MACH_BCM63XX_IRQ_H
+
+#define NR_IRQS 128
+#define MIPS_CPU_IRQ_BASE 0
+
+#endif
diff --git a/arch/mips/include/asm/mach-bcm63xx/spaces.h b/arch/mips/include/asm/mach-bcm63xx/spaces.h
new file mode 100644
index 000000000..1410ed0da
--- /dev/null
+++ b/arch/mips/include/asm/mach-bcm63xx/spaces.h
@@ -0,0 +1,17 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994 - 1999, 2000, 03, 04 Ralf Baechle
+ * Copyright (C) 2000, 2002  Maciej W. Rozycki
+ * Copyright (C) 1990, 1999, 2000 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_BCM63XX_SPACES_H
+#define _ASM_BCM63XX_SPACES_H
+
+#include <asm/bmips-spaces.h>
+
+#include <asm/mach-generic/spaces.h>
+
+#endif /* __ASM_BCM63XX_SPACES_H */
diff --git a/arch/mips/include/asm/mach-bmips/cpu-feature-overrides.h b/arch/mips/include/asm/mach-bmips/cpu-feature-overrides.h
new file mode 100644
index 000000000..68a219d80
--- /dev/null
+++ b/arch/mips/include/asm/mach-bmips/cpu-feature-overrides.h
@@ -0,0 +1,15 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_MACH_BMIPS_CPU_FEATURE_OVERRIDES_H
+#define __ASM_MACH_BMIPS_CPU_FEATURE_OVERRIDES_H
+
+/* Invariants across all BMIPS processors */
+#define cpu_has_vtag_icache		0
+#define cpu_icache_snoops_remote_store	1
+
+/* Processor ISA compatibility is MIPS32R1 */
+#define cpu_has_mips32r1		1
+#define cpu_has_mips32r2		0
+#define cpu_has_mips64r1		0
+#define cpu_has_mips64r2		0
+
+#endif /* __ASM_MACH_BMIPS_CPU_FEATURE_OVERRIDES_H */
diff --git a/arch/mips/include/asm/mach-bmips/ioremap.h b/arch/mips/include/asm/mach-bmips/ioremap.h
new file mode 100644
index 000000000..63b4af991
--- /dev/null
+++ b/arch/mips/include/asm/mach-bmips/ioremap.h
@@ -0,0 +1,29 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_MACH_BMIPS_IOREMAP_H
+#define __ASM_MACH_BMIPS_IOREMAP_H
+
+#include <linux/types.h>
+
+static inline int is_bmips_internal_registers(phys_addr_t offset)
+{
+	if (offset >= 0xfff80000)
+		return 1;
+
+	return 0;
+}
+
+static inline void __iomem *plat_ioremap(phys_addr_t offset, unsigned long size,
+					 unsigned long flags)
+{
+	if (is_bmips_internal_registers(offset))
+		return (void __iomem *)offset;
+
+	return NULL;
+}
+
+static inline int plat_iounmap(const volatile void __iomem *addr)
+{
+	return is_bmips_internal_registers((unsigned long)addr);
+}
+
+#endif /* __ASM_MACH_BMIPS_IOREMAP_H */
diff --git a/arch/mips/include/asm/mach-bmips/spaces.h b/arch/mips/include/asm/mach-bmips/spaces.h
new file mode 100644
index 000000000..c59b28fd9
--- /dev/null
+++ b/arch/mips/include/asm/mach-bmips/spaces.h
@@ -0,0 +1,18 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994 - 1999, 2000, 03, 04 Ralf Baechle
+ * Copyright (C) 2000, 2002  Maciej W. Rozycki
+ * Copyright (C) 1990, 1999, 2000 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_BMIPS_SPACES_H
+#define _ASM_BMIPS_SPACES_H
+
+/* Avoid collisions with system base register (SBR) region on BMIPS3300 */
+#include <asm/bmips-spaces.h>
+
+#include <asm/mach-generic/spaces.h>
+
+#endif /* __ASM_BMIPS_SPACES_H */
diff --git a/arch/mips/include/asm/mach-cavium-octeon/cpu-feature-overrides.h b/arch/mips/include/asm/mach-cavium-octeon/cpu-feature-overrides.h
new file mode 100644
index 000000000..9151dcd9d
--- /dev/null
+++ b/arch/mips/include/asm/mach-cavium-octeon/cpu-feature-overrides.h
@@ -0,0 +1,79 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2004 Cavium Networks
+ */
+#ifndef __ASM_MACH_CAVIUM_OCTEON_CPU_FEATURE_OVERRIDES_H
+#define __ASM_MACH_CAVIUM_OCTEON_CPU_FEATURE_OVERRIDES_H
+
+#include <linux/types.h>
+#include <asm/mipsregs.h>
+
+/*
+ * Cavium Octeons are MIPS64v2 processors
+ */
+#define cpu_dcache_line_size()	128
+#define cpu_icache_line_size()	128
+
+
+#define cpu_has_4kex		1
+#define cpu_has_3k_cache	0
+#define cpu_has_4k_cache	0
+#define cpu_has_counter		1
+#define cpu_has_watch		1
+#define cpu_has_divec		1
+#define cpu_has_vce		0
+#define cpu_has_cache_cdex_p	0
+#define cpu_has_cache_cdex_s	0
+#define cpu_has_prefetch	1
+
+#define cpu_has_llsc		1
+/*
+ * We Disable LL/SC on non SMP systems as it is faster to disable
+ * interrupts for atomic access than a LL/SC.
+ */
+#ifdef CONFIG_SMP
+# define kernel_uses_llsc	1
+#else
+# define kernel_uses_llsc	0
+#endif
+#define cpu_has_vtag_icache	1
+#define cpu_has_dc_aliases	0
+#define cpu_has_ic_fills_f_dc	0
+#define cpu_has_64bits		1
+#define cpu_has_octeon_cache	1
+#define cpu_has_mips32r1	1
+#define cpu_has_mips32r2	1
+#define cpu_has_mips64r1	1
+#define cpu_has_mips64r2	1
+#define cpu_has_dsp		0
+#define cpu_has_dsp2		0
+#define cpu_has_mipsmt		0
+#define cpu_has_vint		0
+#define cpu_has_veic		0
+#define cpu_hwrena_impl_bits	(MIPS_HWRENA_IMPL1 | MIPS_HWRENA_IMPL2)
+#define cpu_has_wsbh            1
+
+#define cpu_has_rixi		(cpu_data[0].cputype != CPU_CAVIUM_OCTEON)
+
+#define ARCH_HAS_SPINLOCK_PREFETCH 1
+#define spin_lock_prefetch(x) prefetch(x)
+#define PREFETCH_STRIDE 128
+
+#ifdef __OCTEON__
+/*
+ * All gcc versions that have OCTEON support define __OCTEON__ and have the
+ *  __builtin_popcount support.
+ */
+#define ARCH_HAS_USABLE_BUILTIN_POPCOUNT 1
+#endif
+
+/*
+ * The last 256MB are reserved for device to device mappings and the
+ * BAR1 hole.
+ */
+#define MAX_DMA32_PFN (((1ULL << 32) - (1ULL << 28)) >> PAGE_SHIFT)
+
+#endif
diff --git a/arch/mips/include/asm/mach-cavium-octeon/irq.h b/arch/mips/include/asm/mach-cavium-octeon/irq.h
new file mode 100644
index 000000000..64b86b9d3
--- /dev/null
+++ b/arch/mips/include/asm/mach-cavium-octeon/irq.h
@@ -0,0 +1,58 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2004-2008 Cavium Networks
+ */
+#ifndef __OCTEON_IRQ_H__
+#define __OCTEON_IRQ_H__
+
+#define NR_IRQS OCTEON_IRQ_LAST
+#define MIPS_CPU_IRQ_BASE OCTEON_IRQ_SW0
+
+enum octeon_irq {
+/* 1 - 8 represent the 8 MIPS standard interrupt sources */
+	OCTEON_IRQ_SW0 = 1,
+	OCTEON_IRQ_SW1,
+/* CIU0, CUI2, CIU4 are 3, 4, 5 */
+	OCTEON_IRQ_5 = 6,
+	OCTEON_IRQ_PERF,
+	OCTEON_IRQ_TIMER,
+/* sources in CIU_INTX_EN0 */
+	OCTEON_IRQ_WORKQ0,
+	OCTEON_IRQ_WDOG0 = OCTEON_IRQ_WORKQ0 + 64,
+	OCTEON_IRQ_MBOX0 = OCTEON_IRQ_WDOG0 + 32,
+	OCTEON_IRQ_MBOX1,
+	OCTEON_IRQ_MBOX2,
+	OCTEON_IRQ_MBOX3,
+	OCTEON_IRQ_PCI_INT0,
+	OCTEON_IRQ_PCI_INT1,
+	OCTEON_IRQ_PCI_INT2,
+	OCTEON_IRQ_PCI_INT3,
+	OCTEON_IRQ_PCI_MSI0,
+	OCTEON_IRQ_PCI_MSI1,
+	OCTEON_IRQ_PCI_MSI2,
+	OCTEON_IRQ_PCI_MSI3,
+
+	OCTEON_IRQ_TWSI,
+	OCTEON_IRQ_TWSI2,
+	OCTEON_IRQ_RML,
+	OCTEON_IRQ_TIMER0,
+	OCTEON_IRQ_TIMER1,
+	OCTEON_IRQ_TIMER2,
+	OCTEON_IRQ_TIMER3,
+#ifndef CONFIG_PCI_MSI
+	OCTEON_IRQ_LAST = 127
+#endif
+};
+
+#ifdef CONFIG_PCI_MSI
+/* 256 - 511 represent the MSI interrupts 0-255 */
+#define OCTEON_IRQ_MSI_BIT0	(256)
+
+#define OCTEON_IRQ_MSI_LAST	 (OCTEON_IRQ_MSI_BIT0 + 255)
+#define OCTEON_IRQ_LAST		 (OCTEON_IRQ_MSI_LAST + 1)
+#endif
+
+#endif
diff --git a/arch/mips/include/asm/mach-cavium-octeon/kernel-entry-init.h b/arch/mips/include/asm/mach-cavium-octeon/kernel-entry-init.h
new file mode 100644
index 000000000..b071a7353
--- /dev/null
+++ b/arch/mips/include/asm/mach-cavium-octeon/kernel-entry-init.h
@@ -0,0 +1,168 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2005-2008 Cavium Networks, Inc
+ */
+#ifndef __ASM_MACH_CAVIUM_OCTEON_KERNEL_ENTRY_H
+#define __ASM_MACH_CAVIUM_OCTEON_KERNEL_ENTRY_H
+
+#define CP0_CVMCTL_REG $9, 7
+#define CP0_CVMMEMCTL_REG $11,7
+#define CP0_PRID_REG $15, 0
+#define CP0_DCACHE_ERR_REG $27, 1
+#define CP0_PRID_OCTEON_PASS1 0x000d0000
+#define CP0_PRID_OCTEON_CN30XX 0x000d0200
+
+.macro	kernel_entry_setup
+	# Registers set by bootloader:
+	# (only 32 bits set by bootloader, all addresses are physical
+	# addresses, and need to have the appropriate memory region set
+	# by the kernel
+	# a0 = argc
+	# a1 = argv (kseg0 compat addr)
+	# a2 = 1 if init core, zero otherwise
+	# a3 = address of boot descriptor block
+	.set push
+	.set arch=octeon
+	# Read the cavium mem control register
+	dmfc0	v0, CP0_CVMMEMCTL_REG
+	# Clear the lower 6 bits, the CVMSEG size
+	dins	v0, $0, 0, 6
+	ori	v0, CONFIG_CAVIUM_OCTEON_CVMSEG_SIZE
+	dmtc0	v0, CP0_CVMMEMCTL_REG	# Write the cavium mem control register
+	dmfc0	v0, CP0_CVMCTL_REG	# Read the cavium control register
+	# Disable unaligned load/store support but leave HW fixup enabled
+	# Needed for octeon specific memcpy
+	or  v0, v0, 0x5001
+	xor v0, v0, 0x1001
+	# First clear off CvmCtl[IPPCI] bit and move the performance
+	# counters interrupt to IRQ 6
+	dli	v1, ~(7 << 7)
+	and	v0, v0, v1
+	ori	v0, v0, (6 << 7)
+
+	mfc0	v1, CP0_PRID_REG
+	and	t1, v1, 0xfff8
+	xor	t1, t1, 0x9000		# 63-P1
+	beqz	t1, 4f
+	and	t1, v1, 0xfff8
+	xor	t1, t1, 0x9008		# 63-P2
+	beqz	t1, 4f
+	and	t1, v1, 0xfff8
+	xor	t1, t1, 0x9100		# 68-P1
+	beqz	t1, 4f
+	and	t1, v1, 0xff00
+	xor	t1, t1, 0x9200		# 66-PX
+	bnez	t1, 5f			# Skip WAR for others.
+	and	t1, v1, 0x00ff
+	slti	t1, t1, 2		# 66-P1.2 and later good.
+	beqz	t1, 5f
+
+4:	# core-16057 work around
+	or	v0, v0, 0x2000		# Set IPREF bit.
+
+5:	# No core-16057 work around
+	# Write the cavium control register
+	dmtc0	v0, CP0_CVMCTL_REG
+	sync
+	# Flush dcache after config change
+	cache	9, 0($0)
+	# Zero all of CVMSEG to make sure parity is correct
+	dli	v0, CONFIG_CAVIUM_OCTEON_CVMSEG_SIZE
+	dsll	v0, 7
+	beqz	v0, 2f
+1:	dsubu	v0, 8
+	sd	$0, -32768(v0)
+	bnez	v0, 1b
+2:
+	mfc0	v0, CP0_PRID_REG
+	bbit0	v0, 15, 1f
+	# OCTEON II or better have bit 15 set.  Clear the error bits.
+	and	t1, v0, 0xff00
+	dli	v0, 0x9500
+	bge	t1, v0, 1f  # OCTEON III has no DCACHE_ERR_REG COP0
+	dli	v0, 0x27
+	dmtc0	v0, CP0_DCACHE_ERR_REG
+1:
+	# Get my core id
+	rdhwr	v0, $0
+	# Jump the master to kernel_entry
+	bne	a2, zero, octeon_main_processor
+	nop
+
+#ifdef CONFIG_SMP
+
+	#
+	# All cores other than the master need to wait here for SMP bootstrap
+	# to begin
+	#
+
+octeon_spin_wait_boot:
+#ifdef CONFIG_RELOCATABLE
+	PTR_LA	t0, octeon_processor_relocated_kernel_entry
+	LONG_L	t0, (t0)
+	beq	zero, t0, 1f
+	nop
+
+	jr	t0
+	nop
+1:
+#endif /* CONFIG_RELOCATABLE */
+
+	# This is the variable where the next core to boot is stored
+	PTR_LA	t0, octeon_processor_boot
+	# Get the core id of the next to be booted
+	LONG_L	t1, (t0)
+	# Keep looping if it isn't me
+	bne t1, v0, octeon_spin_wait_boot
+	nop
+	# Get my GP from the global variable
+	PTR_LA	t0, octeon_processor_gp
+	LONG_L	gp, (t0)
+	# Get my SP from the global variable
+	PTR_LA	t0, octeon_processor_sp
+	LONG_L	sp, (t0)
+	# Set the SP global variable to zero so the master knows we've started
+	LONG_S	zero, (t0)
+#ifdef __OCTEON__
+	syncw
+	syncw
+#else
+	sync
+#endif
+	# Jump to the normal Linux SMP entry point
+	j   smp_bootstrap
+	nop
+#else /* CONFIG_SMP */
+
+	#
+	# Someone tried to boot SMP with a non SMP kernel. All extra cores
+	# will halt here.
+	#
+octeon_wait_forever:
+	wait
+	b   octeon_wait_forever
+	nop
+
+#endif /* CONFIG_SMP */
+octeon_main_processor:
+	.set pop
+.endm
+
+/*
+ * Do SMP slave processor setup necessary before we can safely execute C code.
+ */
+	.macro	smp_slave_setup
+	.endm
+
+#define USE_KEXEC_SMP_WAIT_FINAL
+	.macro  kexec_smp_wait_final
+	.set push
+	.set noreorder
+	synci		0($0)
+	.set pop
+	.endm
+
+#endif /* __ASM_MACH_CAVIUM_OCTEON_KERNEL_ENTRY_H */
diff --git a/arch/mips/include/asm/mach-cavium-octeon/mangle-port.h b/arch/mips/include/asm/mach-cavium-octeon/mangle-port.h
new file mode 100644
index 000000000..239fcc874
--- /dev/null
+++ b/arch/mips/include/asm/mach-cavium-octeon/mangle-port.h
@@ -0,0 +1,64 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003, 2004 Ralf Baechle
+ */
+#ifndef __ASM_MACH_GENERIC_MANGLE_PORT_H
+#define __ASM_MACH_GENERIC_MANGLE_PORT_H
+
+#include <asm/byteorder.h>
+
+#ifdef __BIG_ENDIAN
+
+static inline bool __should_swizzle_bits(volatile void *a)
+{
+	extern const bool octeon_should_swizzle_table[];
+	u64 did = ((u64)(uintptr_t)a >> 40) & 0xff;
+
+	return octeon_should_swizzle_table[did];
+}
+
+# define __swizzle_addr_b(port)	(port)
+# define __swizzle_addr_w(port)	(port)
+# define __swizzle_addr_l(port)	(port)
+# define __swizzle_addr_q(port)	(port)
+
+#else /* __LITTLE_ENDIAN */
+
+#define __should_swizzle_bits(a)	false
+
+static inline bool __should_swizzle_addr(u64 p)
+{
+	/* boot bus? */
+	return ((p >> 40) & 0xff) == 0;
+}
+
+# define __swizzle_addr_b(port)	\
+	(__should_swizzle_addr(port) ? (port) ^ 7 : (port))
+# define __swizzle_addr_w(port)	\
+	(__should_swizzle_addr(port) ? (port) ^ 6 : (port))
+# define __swizzle_addr_l(port)	\
+	(__should_swizzle_addr(port) ? (port) ^ 4 : (port))
+# define __swizzle_addr_q(port)	(port)
+
+#endif /* __BIG_ENDIAN */
+
+
+# define ioswabb(a, x)		(x)
+# define __mem_ioswabb(a, x)	(x)
+# define ioswabw(a, x)		(__should_swizzle_bits(a) ?		\
+				 le16_to_cpu((__force __le16)(x)) :	\
+				 (x))
+# define __mem_ioswabw(a, x)	(x)
+# define ioswabl(a, x)		(__should_swizzle_bits(a) ?		\
+				 le32_to_cpu((__force __le32)(x)) :	\
+				 (x))
+# define __mem_ioswabl(a, x)	(x)
+# define ioswabq(a, x)		(__should_swizzle_bits(a) ?		\
+				 le64_to_cpu((__force __le64)(x)) :	\
+				 (x))
+# define __mem_ioswabq(a, x)	(x)
+
+#endif /* __ASM_MACH_GENERIC_MANGLE_PORT_H */
diff --git a/arch/mips/include/asm/mach-cavium-octeon/spaces.h b/arch/mips/include/asm/mach-cavium-octeon/spaces.h
new file mode 100644
index 000000000..daa91accf
--- /dev/null
+++ b/arch/mips/include/asm/mach-cavium-octeon/spaces.h
@@ -0,0 +1,24 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2012 Cavium, Inc.
+ */
+#ifndef _ASM_MACH_CAVIUM_OCTEON_SPACES_H
+#define _ASM_MACH_CAVIUM_OCTEON_SPACES_H
+
+#include <linux/const.h>
+
+#ifdef CONFIG_64BIT
+/* They are all the same and some OCTEON II cores cannot handle 0xa8.. */
+#define CAC_BASE		_AC(0x8000000000000000, UL)
+#define UNCAC_BASE		_AC(0x8000000000000000, UL)
+#define IO_BASE			_AC(0x8000000000000000, UL)
+
+
+#endif /* CONFIG_64BIT */
+
+#include <asm/mach-generic/spaces.h>
+
+#endif /* _ASM_MACH_CAVIUM_OCTEON_SPACES_H */
diff --git a/arch/mips/include/asm/mach-cobalt/cobalt.h b/arch/mips/include/asm/mach-cobalt/cobalt.h
new file mode 100644
index 000000000..5b9fce73f
--- /dev/null
+++ b/arch/mips/include/asm/mach-cobalt/cobalt.h
@@ -0,0 +1,22 @@
+/*
+ * The Cobalt board ID information.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1997 Cobalt Microserver
+ * Copyright (C) 1997, 2003 Ralf Baechle
+ * Copyright (C) 2001, 2002, 2003 Liam Davies (ldavies@agile.tv)
+ */
+#ifndef __ASM_COBALT_H
+#define __ASM_COBALT_H
+
+extern int cobalt_board_id;
+
+#define COBALT_BRD_ID_QUBE1    0x3
+#define COBALT_BRD_ID_RAQ1     0x4
+#define COBALT_BRD_ID_QUBE2    0x5
+#define COBALT_BRD_ID_RAQ2     0x6
+
+#endif /* __ASM_COBALT_H */
diff --git a/arch/mips/include/asm/mach-cobalt/cpu-feature-overrides.h b/arch/mips/include/asm/mach-cobalt/cpu-feature-overrides.h
new file mode 100644
index 000000000..031924584
--- /dev/null
+++ b/arch/mips/include/asm/mach-cobalt/cpu-feature-overrides.h
@@ -0,0 +1,56 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2006, 07 Ralf Baechle (ralf@linux-mips.org)
+ */
+#ifndef __ASM_COBALT_CPU_FEATURE_OVERRIDES_H
+#define __ASM_COBALT_CPU_FEATURE_OVERRIDES_H
+
+
+#define cpu_has_tlb		1
+#define cpu_has_4kex		1
+#define cpu_has_3k_cache	0
+#define cpu_has_4k_cache	1
+#define cpu_has_32fpr		1
+#define cpu_has_counter		1
+#define cpu_has_watch		0
+#define cpu_has_divec		1
+#define cpu_has_vce		0
+#define cpu_has_cache_cdex_p	0
+#define cpu_has_cache_cdex_s	0
+#define cpu_has_prefetch	0
+#define cpu_has_mcheck		0
+#define cpu_has_ejtag		0
+
+#define cpu_has_inclusive_pcaches	0
+#define cpu_dcache_line_size()	32
+#define cpu_icache_line_size()	32
+#define cpu_scache_line_size()	0
+
+#ifdef CONFIG_64BIT
+#define cpu_has_llsc		0
+#else
+#define cpu_has_llsc		1
+#endif
+
+#define cpu_has_mips16		0
+#define cpu_has_mips16e2	0
+#define cpu_has_mdmx		0
+#define cpu_has_mips3d		0
+#define cpu_has_smartmips	0
+#define cpu_has_vtag_icache	0
+#define cpu_has_ic_fills_f_dc	0
+#define cpu_icache_snoops_remote_store	0
+#define cpu_has_dsp		0
+#define cpu_has_dsp2		0
+#define cpu_has_mipsmt		0
+#define cpu_has_userlocal	0
+
+#define cpu_has_mips32r1	0
+#define cpu_has_mips32r2	0
+#define cpu_has_mips64r1	0
+#define cpu_has_mips64r2	0
+
+#endif /* __ASM_COBALT_CPU_FEATURE_OVERRIDES_H */
diff --git a/arch/mips/include/asm/mach-cobalt/irq.h b/arch/mips/include/asm/mach-cobalt/irq.h
new file mode 100644
index 000000000..9da9acf5d
--- /dev/null
+++ b/arch/mips/include/asm/mach-cobalt/irq.h
@@ -0,0 +1,57 @@
+/*
+ * Cobalt IRQ definitions.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1997 Cobalt Microserver
+ * Copyright (C) 1997, 2003 Ralf Baechle
+ * Copyright (C) 2001-2003 Liam Davies (ldavies@agile.tv)
+ * Copyright (C) 2007 Yoichi Yuasa <yuasa@linux-mips.org>
+ */
+#ifndef _ASM_COBALT_IRQ_H
+#define _ASM_COBALT_IRQ_H
+
+/*
+ * i8259 interrupts used on Cobalt:
+ *
+ *	8  - RTC
+ *	9  - PCI slot
+ *	14 - IDE0
+ *	15 - IDE1(no connector on board)
+ */
+#define I8259A_IRQ_BASE			0
+
+#define PCISLOT_IRQ			(I8259A_IRQ_BASE + 9)
+
+/*
+ * CPU interrupts used on Cobalt:
+ *
+ *	0 - Software interrupt 0 (unused)
+ *	1 - Software interrupt 0 (unused)
+ *	2 - cascade GT64111
+ *	3 - ethernet or SCSI host controller
+ *	4 - ethernet
+ *	5 - 16550 UART
+ *	6 - cascade i8259
+ *	7 - CP0 counter
+ */
+#define MIPS_CPU_IRQ_BASE		16
+
+#define GT641XX_CASCADE_IRQ		(MIPS_CPU_IRQ_BASE + 2)
+#define RAQ2_SCSI_IRQ			(MIPS_CPU_IRQ_BASE + 3)
+#define ETH0_IRQ			(MIPS_CPU_IRQ_BASE + 3)
+#define QUBE1_ETH0_IRQ			(MIPS_CPU_IRQ_BASE + 4)
+#define ETH1_IRQ			(MIPS_CPU_IRQ_BASE + 4)
+#define SERIAL_IRQ			(MIPS_CPU_IRQ_BASE + 5)
+#define SCSI_IRQ			(MIPS_CPU_IRQ_BASE + 5)
+#define I8259_CASCADE_IRQ		(MIPS_CPU_IRQ_BASE + 6)
+
+#define GT641XX_IRQ_BASE		24
+
+#include <asm/irq_gt641xx.h>
+
+#define NR_IRQS					(GT641XX_PCI_INT3_IRQ + 1)
+
+#endif /* _ASM_COBALT_IRQ_H */
diff --git a/arch/mips/include/asm/mach-cobalt/mach-gt64120.h b/arch/mips/include/asm/mach-cobalt/mach-gt64120.h
new file mode 100644
index 000000000..ddb968a55
--- /dev/null
+++ b/arch/mips/include/asm/mach-cobalt/mach-gt64120.h
@@ -0,0 +1,14 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ *  Copyright (C) 2006	Yoichi Yuasa <yuasa@linux-mips.org>
+ */
+#ifndef _COBALT_MACH_GT64120_H
+#define _COBALT_MACH_GT64120_H
+
+/*
+ * Cobalt uses GT64111. GT64111 is almost the same as GT64120.
+ */
+
+#define GT64120_BASE	CKSEG1ADDR(GT_DEF_BASE)
+
+#endif /* _COBALT_MACH_GT64120_H */
diff --git a/arch/mips/include/asm/mach-db1x00/bcsr.h b/arch/mips/include/asm/mach-db1x00/bcsr.h
new file mode 100644
index 000000000..4a27738e8
--- /dev/null
+++ b/arch/mips/include/asm/mach-db1x00/bcsr.h
@@ -0,0 +1,261 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * bcsr.h -- Db1xxx/Pb1xxx Devboard CPLD registers ("BCSR") abstraction.
+ *
+ * All Alchemy development boards (except, of course, the weird PB1000)
+ * have a few registers in a CPLD with standardised layout; they mostly
+ * only differ in base address and bit meanings in the RESETS and BOARD
+ * registers.
+ *
+ * All data taken from the official AMD board documentation sheets.
+ */
+
+#ifndef _DB1XXX_BCSR_H_
+#define _DB1XXX_BCSR_H_
+
+
+/* BCSR base addresses on various boards. BCSR base 2 refers to the
+ * physical address of the first HEXLEDS register, which is usually
+ * a variable offset from the WHOAMI register.
+ */
+
+/* DB1000, DB1100, DB1500, PB1100, PB1500 */
+#define DB1000_BCSR_PHYS_ADDR	0x0E000000
+#define DB1000_BCSR_HEXLED_OFS	0x01000000
+
+#define DB1550_BCSR_PHYS_ADDR	0x0F000000
+#define DB1550_BCSR_HEXLED_OFS	0x00400000
+
+#define PB1550_BCSR_PHYS_ADDR	0x0F000000
+#define PB1550_BCSR_HEXLED_OFS	0x00800000
+
+#define DB1200_BCSR_PHYS_ADDR	0x19800000
+#define DB1200_BCSR_HEXLED_OFS	0x00400000
+
+#define PB1200_BCSR_PHYS_ADDR	0x0D800000
+#define PB1200_BCSR_HEXLED_OFS	0x00400000
+
+#define DB1300_BCSR_PHYS_ADDR	0x19800000
+#define DB1300_BCSR_HEXLED_OFS	0x00400000
+
+enum bcsr_id {
+	/* BCSR base 1 */
+	BCSR_WHOAMI	= 0,
+	BCSR_STATUS,
+	BCSR_SWITCHES,
+	BCSR_RESETS,
+	BCSR_PCMCIA,
+	BCSR_BOARD,
+	BCSR_LEDS,
+	BCSR_SYSTEM,
+	/* Au1200/1300 based boards */
+	BCSR_INTCLR,
+	BCSR_INTSET,
+	BCSR_MASKCLR,
+	BCSR_MASKSET,
+	BCSR_SIGSTAT,
+	BCSR_INTSTAT,
+
+	/* BCSR base 2 */
+	BCSR_HEXLEDS,
+	BCSR_RSVD1,
+	BCSR_HEXCLEAR,
+
+	BCSR_CNT,
+};
+
+/* register offsets, valid for all Db1xxx/Pb1xxx boards */
+#define BCSR_REG_WHOAMI		0x00
+#define BCSR_REG_STATUS		0x04
+#define BCSR_REG_SWITCHES	0x08
+#define BCSR_REG_RESETS		0x0c
+#define BCSR_REG_PCMCIA		0x10
+#define BCSR_REG_BOARD		0x14
+#define BCSR_REG_LEDS		0x18
+#define BCSR_REG_SYSTEM		0x1c
+/* Au1200/Au1300 based boards: CPLD IRQ muxer */
+#define BCSR_REG_INTCLR		0x20
+#define BCSR_REG_INTSET		0x24
+#define BCSR_REG_MASKCLR	0x28
+#define BCSR_REG_MASKSET	0x2c
+#define BCSR_REG_SIGSTAT	0x30
+#define BCSR_REG_INTSTAT	0x34
+
+/* hexled control, offset from BCSR base 2 */
+#define BCSR_REG_HEXLEDS	0x00
+#define BCSR_REG_HEXCLEAR	0x08
+
+/*
+ * Register Bits and Pieces.
+ */
+#define BCSR_WHOAMI_DCID(x)		((x) & 0xf)
+#define BCSR_WHOAMI_CPLD(x)		(((x) >> 4) & 0xf)
+#define BCSR_WHOAMI_BOARD(x)		(((x) >> 8) & 0xf)
+
+/* register "WHOAMI" bits 11:8 identify the board */
+enum bcsr_whoami_boards {
+	BCSR_WHOAMI_PB1500 = 1,
+	BCSR_WHOAMI_PB1500R2,
+	BCSR_WHOAMI_PB1100,
+	BCSR_WHOAMI_DB1000,
+	BCSR_WHOAMI_DB1100,
+	BCSR_WHOAMI_DB1500,
+	BCSR_WHOAMI_DB1550,
+	BCSR_WHOAMI_PB1550_DDR,
+	BCSR_WHOAMI_PB1550 = BCSR_WHOAMI_PB1550_DDR,
+	BCSR_WHOAMI_PB1550_SDR,
+	BCSR_WHOAMI_PB1200_DDR1,
+	BCSR_WHOAMI_PB1200 = BCSR_WHOAMI_PB1200_DDR1,
+	BCSR_WHOAMI_PB1200_DDR2,
+	BCSR_WHOAMI_DB1200,
+	BCSR_WHOAMI_DB1300,
+};
+
+/* STATUS reg.	Unless otherwise noted, they're valid on all boards.
+ * PB1200 = DB1200.
+ */
+#define BCSR_STATUS_PC0VS		0x0003
+#define BCSR_STATUS_PC1VS		0x000C
+#define BCSR_STATUS_PC0FI		0x0010
+#define BCSR_STATUS_PC1FI		0x0020
+#define BCSR_STATUS_PB1550_SWAPBOOT	0x0040
+#define BCSR_STATUS_SRAMWIDTH		0x0080
+#define BCSR_STATUS_FLASHBUSY		0x0100
+#define BCSR_STATUS_ROMBUSY		0x0400
+#define BCSR_STATUS_SD0WP		0x0400	/* DB1200/DB1300:SD1 */
+#define BCSR_STATUS_SD1WP		0x0800
+#define BCSR_STATUS_USBOTGID		0x0800	/* PB/DB1550 */
+#define BCSR_STATUS_DB1000_SWAPBOOT	0x2000
+#define BCSR_STATUS_DB1200_SWAPBOOT	0x0040	/* DB1200/1300 */
+#define BCSR_STATUS_IDECBLID		0x0200	/* DB1200/1300 */
+#define BCSR_STATUS_DB1200_U0RXD	0x1000	/* DB1200 */
+#define BCSR_STATUS_DB1200_U1RXD	0x2000	/* DB1200 */
+#define BCSR_STATUS_FLASHDEN		0xC000
+#define BCSR_STATUS_DB1550_U0RXD	0x1000	/* DB1550 */
+#define BCSR_STATUS_DB1550_U3RXD	0x2000	/* DB1550 */
+#define BCSR_STATUS_PB1550_U0RXD	0x1000	/* PB1550 */
+#define BCSR_STATUS_PB1550_U1RXD	0x2000	/* PB1550 */
+#define BCSR_STATUS_PB1550_U3RXD	0x8000	/* PB1550 */
+
+#define BCSR_STATUS_CFWP		0x4000	/* DB1300 */
+#define BCSR_STATUS_USBOCn		0x2000	/* DB1300 */
+#define BCSR_STATUS_OTGOCn		0x1000	/* DB1300 */
+#define BCSR_STATUS_DCDMARQ		0x0010	/* DB1300 */
+#define BCSR_STATUS_IDEDMARQ		0x0020	/* DB1300 */
+
+/* DB/PB1000,1100,1500,1550 */
+#define BCSR_RESETS_PHY0		0x0001
+#define BCSR_RESETS_PHY1		0x0002
+#define BCSR_RESETS_DC			0x0004
+#define BCSR_RESETS_FIR_SEL		0x2000
+#define BCSR_RESETS_IRDA_MODE_MASK	0xC000
+#define BCSR_RESETS_IRDA_MODE_FULL	0x0000
+#define BCSR_RESETS_PB1550_WSCFSM	0x2000
+#define BCSR_RESETS_IRDA_MODE_OFF	0x4000
+#define BCSR_RESETS_IRDA_MODE_2_3	0x8000
+#define BCSR_RESETS_IRDA_MODE_1_3	0xC000
+#define BCSR_RESETS_DMAREQ		0x8000	/* PB1550 */
+
+#define BCSR_BOARD_PCIM66EN		0x0001
+#define BCSR_BOARD_SD0PWR		0x0040
+#define BCSR_BOARD_SD1PWR		0x0080
+#define BCSR_BOARD_PCIM33		0x0100
+#define BCSR_BOARD_PCIEXTARB		0x0200
+#define BCSR_BOARD_GPIO200RST		0x0400
+#define BCSR_BOARD_PCICLKOUT		0x0800
+#define BCSR_BOARD_PB1100_SD0PWR	0x0400
+#define BCSR_BOARD_PB1100_SD1PWR	0x0800
+#define BCSR_BOARD_PCICFG		0x1000
+#define BCSR_BOARD_SPISEL		0x2000	/* PB/DB1550 */
+#define BCSR_BOARD_SD0WP		0x4000	/* DB1100 */
+#define BCSR_BOARD_SD1WP		0x8000	/* DB1100 */
+
+
+/* DB/PB1200/1300 */
+#define BCSR_RESETS_ETH			0x0001
+#define BCSR_RESETS_CAMERA		0x0002
+#define BCSR_RESETS_DC			0x0004
+#define BCSR_RESETS_IDE			0x0008
+#define BCSR_RESETS_TV			0x0010	/* DB1200/1300 */
+/* Not resets but in the same register */
+#define BCSR_RESETS_PWMR1MUX		0x0800	/* DB1200 */
+#define BCSR_RESETS_PB1200_WSCFSM	0x0800	/* PB1200 */
+#define BCSR_RESETS_PSC0MUX		0x1000
+#define BCSR_RESETS_PSC1MUX		0x2000
+#define BCSR_RESETS_SPISEL		0x4000
+#define BCSR_RESETS_SD1MUX		0x8000	/* PB1200 */
+
+#define BCSR_RESETS_VDDQSHDN		0x0200	/* DB1300 */
+#define BCSR_RESETS_OTPPGM		0x0400	/* DB1300 */
+#define BCSR_RESETS_OTPSCLK		0x0800	/* DB1300 */
+#define BCSR_RESETS_OTPWRPROT		0x1000	/* DB1300 */
+#define BCSR_RESETS_OTPCSB		0x2000	/* DB1300 */
+#define BCSR_RESETS_OTGPWR		0x4000	/* DB1300 */
+#define BCSR_RESETS_USBHPWR		0x8000	/* DB1300 */
+
+#define BCSR_BOARD_LCDVEE		0x0001
+#define BCSR_BOARD_LCDVDD		0x0002
+#define BCSR_BOARD_LCDBL		0x0004
+#define BCSR_BOARD_CAMSNAP		0x0010
+#define BCSR_BOARD_CAMPWR		0x0020
+#define BCSR_BOARD_SD0PWR		0x0040
+#define BCSR_BOARD_CAMCS		0x0010	/* DB1300 */
+#define BCSR_BOARD_HDMI_DE		0x0040	/* DB1300 */
+
+#define BCSR_SWITCHES_DIP		0x00FF
+#define BCSR_SWITCHES_DIP_1		0x0080
+#define BCSR_SWITCHES_DIP_2		0x0040
+#define BCSR_SWITCHES_DIP_3		0x0020
+#define BCSR_SWITCHES_DIP_4		0x0010
+#define BCSR_SWITCHES_DIP_5		0x0008
+#define BCSR_SWITCHES_DIP_6		0x0004
+#define BCSR_SWITCHES_DIP_7		0x0002
+#define BCSR_SWITCHES_DIP_8		0x0001
+#define BCSR_SWITCHES_ROTARY		0x0F00
+
+
+#define BCSR_PCMCIA_PC0VPP		0x0003
+#define BCSR_PCMCIA_PC0VCC		0x000C
+#define BCSR_PCMCIA_PC0DRVEN		0x0010
+#define BCSR_PCMCIA_PC0RST		0x0080
+#define BCSR_PCMCIA_PC1VPP		0x0300
+#define BCSR_PCMCIA_PC1VCC		0x0C00
+#define BCSR_PCMCIA_PC1DRVEN		0x1000
+#define BCSR_PCMCIA_PC1RST		0x8000
+
+
+#define BCSR_LEDS_DECIMALS		0x0003
+#define BCSR_LEDS_LED0			0x0100
+#define BCSR_LEDS_LED1			0x0200
+#define BCSR_LEDS_LED2			0x0400
+#define BCSR_LEDS_LED3			0x0800
+
+
+#define BCSR_SYSTEM_RESET		0x8000	/* clear to reset */
+#define BCSR_SYSTEM_PWROFF		0x4000	/* set to power off */
+#define BCSR_SYSTEM_VDDI		0x001F	/* PB1xxx boards */
+#define BCSR_SYSTEM_DEBUGCSMASK		0x003F	/* DB1300 */
+#define BCSR_SYSTEM_UDMAMODE		0x0100	/* DB1300 */
+#define BCSR_SYSTEM_WAKEONIRQ		0x0200	/* DB1300 */
+#define BCSR_SYSTEM_VDDI1300		0x3C00	/* DB1300 */
+
+
+
+/* initialize BCSR for a board. Provide the PHYSICAL addresses of both
+ * BCSR spaces.
+ */
+void __init bcsr_init(unsigned long bcsr1_phys, unsigned long bcsr2_phys);
+
+/* read a board register */
+unsigned short bcsr_read(enum bcsr_id reg);
+
+/* write to a board register */
+void bcsr_write(enum bcsr_id reg, unsigned short val);
+
+/* modify a register. clear bits set in 'clr', set bits set in 'set' */
+void bcsr_mod(enum bcsr_id reg, unsigned short clr, unsigned short set);
+
+/* install CPLD IRQ demuxer (DB1200/PB1200) */
+void __init bcsr_init_irq(int csc_start, int csc_end, int hook_irq);
+
+#endif
diff --git a/arch/mips/include/asm/mach-db1x00/irq.h b/arch/mips/include/asm/mach-db1x00/irq.h
new file mode 100644
index 000000000..15b266932
--- /dev/null
+++ b/arch/mips/include/asm/mach-db1x00/irq.h
@@ -0,0 +1,23 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003 by Ralf Baechle
+ */
+#ifndef __ASM_MACH_GENERIC_IRQ_H
+#define __ASM_MACH_GENERIC_IRQ_H
+
+
+#ifdef NR_IRQS
+#undef NR_IRQS
+#endif
+
+#ifndef MIPS_CPU_IRQ_BASE
+#define MIPS_CPU_IRQ_BASE 0
+#endif
+
+/* 8 (MIPS) + 128 (au1300) + 16 (cpld) */
+#define NR_IRQS 152
+
+#endif /* __ASM_MACH_GENERIC_IRQ_H */
diff --git a/arch/mips/include/asm/mach-dec/cpu-feature-overrides.h b/arch/mips/include/asm/mach-dec/cpu-feature-overrides.h
new file mode 100644
index 000000000..3ddc4b4dc
--- /dev/null
+++ b/arch/mips/include/asm/mach-dec/cpu-feature-overrides.h
@@ -0,0 +1,96 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ *	CPU feature overrides for DECstation systems.  Two variations
+ *	are generally applicable.
+ *
+ *	Copyright (C) 2013  Maciej W. Rozycki
+ */
+#ifndef __ASM_MACH_DEC_CPU_FEATURE_OVERRIDES_H
+#define __ASM_MACH_DEC_CPU_FEATURE_OVERRIDES_H
+
+/* Generic ones first.  */
+#define cpu_has_tlb			1
+#define cpu_has_tlbinv			0
+#define cpu_has_segments		0
+#define cpu_has_eva			0
+#define cpu_has_htw			0
+#define cpu_has_rixiex			0
+#define cpu_has_maar			0
+#define cpu_has_rw_llb			0
+#define cpu_has_divec			0
+#define cpu_has_prefetch		0
+#define cpu_has_mcheck			0
+#define cpu_has_ejtag			0
+#define cpu_has_mips16			0
+#define cpu_has_mips16e2		0
+#define cpu_has_mdmx			0
+#define cpu_has_mips3d			0
+#define cpu_has_smartmips		0
+#define cpu_has_rixi			0
+#define cpu_has_xpa			0
+#define cpu_has_vtag_icache		0
+#define cpu_has_ic_fills_f_dc		0
+#define cpu_has_pindexed_dcache		0
+#define cpu_icache_snoops_remote_store	1
+#define cpu_has_mips_4			0
+#define cpu_has_mips_5			0
+#define cpu_has_mips32r1		0
+#define cpu_has_mips32r2		0
+#define cpu_has_mips64r1		0
+#define cpu_has_mips64r2		0
+#define cpu_has_dsp			0
+#define cpu_has_dsp2			0
+#define cpu_has_mipsmt			0
+#define cpu_has_userlocal		0
+#define cpu_has_perf_cntr_intr_bit	0
+#define cpu_has_vz			0
+#define cpu_has_fre			0
+#define cpu_has_cdmm			0
+
+/* R3k-specific ones.  */
+#ifdef CONFIG_CPU_R3000
+#define cpu_has_3kex			1
+#define cpu_has_4kex			0
+#define cpu_has_3k_cache		1
+#define cpu_has_4k_cache		0
+#define cpu_has_32fpr			0
+#define cpu_has_counter			0
+#define cpu_has_watch			0
+#define cpu_has_vce			0
+#define cpu_has_cache_cdex_p		0
+#define cpu_has_cache_cdex_s		0
+#define cpu_has_llsc			0
+#define cpu_has_dc_aliases		0
+#define cpu_has_mips_2			0
+#define cpu_has_mips_3			0
+#define cpu_has_nofpuex			1
+#define cpu_has_inclusive_pcaches	0
+#define cpu_dcache_line_size()		4
+#define cpu_icache_line_size()		4
+#define cpu_scache_line_size()		0
+#endif /* CONFIG_CPU_R3000 */
+
+/* R4k-specific ones.  */
+#ifdef CONFIG_CPU_R4X00
+#define cpu_has_3kex			0
+#define cpu_has_4kex			1
+#define cpu_has_3k_cache		0
+#define cpu_has_4k_cache		1
+#define cpu_has_32fpr			1
+#define cpu_has_counter			1
+#define cpu_has_watch			1
+#define cpu_has_vce			1
+#define cpu_has_cache_cdex_p		1
+#define cpu_has_cache_cdex_s		1
+#define cpu_has_llsc			1
+#define cpu_has_dc_aliases		(PAGE_SIZE < 0x4000)
+#define cpu_has_mips_2			1
+#define cpu_has_mips_3			1
+#define cpu_has_nofpuex			0
+#define cpu_has_inclusive_pcaches	1
+#define cpu_dcache_line_size()		16
+#define cpu_icache_line_size()		16
+#define cpu_scache_line_size()		32
+#endif /* CONFIG_CPU_R4X00 */
+
+#endif /* __ASM_MACH_DEC_CPU_FEATURE_OVERRIDES_H */
diff --git a/arch/mips/include/asm/mach-dec/mc146818rtc.h b/arch/mips/include/asm/mach-dec/mc146818rtc.h
new file mode 100644
index 000000000..d4614e2a8
--- /dev/null
+++ b/arch/mips/include/asm/mach-dec/mc146818rtc.h
@@ -0,0 +1,39 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * RTC definitions for DECstation style attached Dallas DS1287 chip.
+ *
+ * Copyright (C) 1998, 2001 by Ralf Baechle
+ * Copyright (C) 1998 by Harald Koerfgen
+ * Copyright (C) 2002, 2005  Maciej W. Rozycki
+ */
+#ifndef __ASM_MIPS_DEC_RTC_DEC_H
+#define __ASM_MIPS_DEC_RTC_DEC_H
+
+#include <linux/types.h>
+#include <asm/addrspace.h>
+#include <asm/dec/system.h>
+
+extern volatile u8 *dec_rtc_base;
+
+#define ARCH_RTC_LOCATION
+
+#define RTC_PORT(x)	CPHYSADDR((long)dec_rtc_base)
+#define RTC_IO_EXTENT	dec_kn_slot_size
+#define RTC_IOMAPPED	0
+#undef RTC_IRQ
+
+#define RTC_DEC_YEAR	0x3f	/* Where we store the real year on DECs.  */
+
+static inline unsigned char CMOS_READ(unsigned long addr)
+{
+	return dec_rtc_base[addr * 4];
+}
+
+static inline void CMOS_WRITE(unsigned char data, unsigned long addr)
+{
+	dec_rtc_base[addr * 4] = data;
+}
+
+#define RTC_ALWAYS_BCD	0
+
+#endif /* __ASM_MIPS_DEC_RTC_DEC_H */
diff --git a/arch/mips/include/asm/mach-generic/cpu-feature-overrides.h b/arch/mips/include/asm/mach-generic/cpu-feature-overrides.h
new file mode 100644
index 000000000..42be9e9ce
--- /dev/null
+++ b/arch/mips/include/asm/mach-generic/cpu-feature-overrides.h
@@ -0,0 +1,13 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003 Ralf Baechle
+ */
+#ifndef __ASM_MACH_GENERIC_CPU_FEATURE_OVERRIDES_H
+#define __ASM_MACH_GENERIC_CPU_FEATURE_OVERRIDES_H
+
+/* Intentionally empty file ...	 */
+
+#endif /* __ASM_MACH_GENERIC_CPU_FEATURE_OVERRIDES_H */
diff --git a/arch/mips/include/asm/mach-generic/floppy.h b/arch/mips/include/asm/mach-generic/floppy.h
new file mode 100644
index 000000000..e0c9cd41f
--- /dev/null
+++ b/arch/mips/include/asm/mach-generic/floppy.h
@@ -0,0 +1,133 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1996, 1997, 1998, 2003 by Ralf Baechle
+ */
+#ifndef __ASM_MACH_GENERIC_FLOPPY_H
+#define __ASM_MACH_GENERIC_FLOPPY_H
+
+#include <linux/delay.h>
+#include <linux/ioport.h>
+#include <linux/sched.h>
+#include <linux/linkage.h>
+#include <linux/types.h>
+#include <linux/mm.h>
+
+#include <asm/bootinfo.h>
+#include <asm/cachectl.h>
+#include <asm/dma.h>
+#include <asm/floppy.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+
+/*
+ * How to access the FDC's registers.
+ */
+static inline unsigned char fd_inb(unsigned int base, unsigned int reg)
+{
+	return inb_p(base + reg);
+}
+
+static inline void fd_outb(unsigned char value, unsigned int base, unsigned int reg)
+{
+	outb_p(value, base + reg);
+}
+
+/*
+ * How to access the floppy DMA functions.
+ */
+static inline void fd_enable_dma(void)
+{
+	enable_dma(FLOPPY_DMA);
+}
+
+static inline void fd_disable_dma(void)
+{
+	disable_dma(FLOPPY_DMA);
+}
+
+static inline int fd_request_dma(void)
+{
+	return request_dma(FLOPPY_DMA, "floppy");
+}
+
+static inline void fd_free_dma(void)
+{
+	free_dma(FLOPPY_DMA);
+}
+
+static inline void fd_clear_dma_ff(void)
+{
+	clear_dma_ff(FLOPPY_DMA);
+}
+
+static inline void fd_set_dma_mode(char mode)
+{
+	set_dma_mode(FLOPPY_DMA, mode);
+}
+
+static inline void fd_set_dma_addr(char *addr)
+{
+	set_dma_addr(FLOPPY_DMA, (unsigned long) addr);
+}
+
+static inline void fd_set_dma_count(unsigned int count)
+{
+	set_dma_count(FLOPPY_DMA, count);
+}
+
+static inline int fd_get_dma_residue(void)
+{
+	return get_dma_residue(FLOPPY_DMA);
+}
+
+static inline void fd_enable_irq(void)
+{
+	enable_irq(FLOPPY_IRQ);
+}
+
+static inline void fd_disable_irq(void)
+{
+	disable_irq(FLOPPY_IRQ);
+}
+
+static inline int fd_request_irq(void)
+{
+	return request_irq(FLOPPY_IRQ, floppy_interrupt,
+			   0, "floppy", NULL);
+}
+
+static inline void fd_free_irq(void)
+{
+	free_irq(FLOPPY_IRQ, NULL);
+}
+
+#define fd_free_irq()		free_irq(FLOPPY_IRQ, NULL);
+
+
+static inline unsigned long fd_getfdaddr1(void)
+{
+	return 0x3f0;
+}
+
+static inline unsigned long fd_dma_mem_alloc(unsigned long size)
+{
+	return __get_dma_pages(GFP_KERNEL, get_order(size));
+}
+
+static inline void fd_dma_mem_free(unsigned long addr, unsigned long size)
+{
+	free_pages(addr, get_order(size));
+}
+
+static inline unsigned long fd_drive_type(unsigned long n)
+{
+	if (n == 0)
+		return 4;	/* 3,5", 1.44mb */
+
+	return 0;
+}
+
+#endif /* __ASM_MACH_GENERIC_FLOPPY_H */
diff --git a/arch/mips/include/asm/mach-generic/ide.h b/arch/mips/include/asm/mach-generic/ide.h
new file mode 100644
index 000000000..4ae5fbcb1
--- /dev/null
+++ b/arch/mips/include/asm/mach-generic/ide.h
@@ -0,0 +1,138 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994-1996  Linus Torvalds & authors
+ *
+ * Copied from i386; many of the especially older MIPS or ISA-based platforms
+ * are basically identical.  Using this file probably implies i8259 PIC
+ * support in a system but the very least interrupt numbers 0 - 15 need to
+ * be put aside for legacy devices.
+ */
+#ifndef __ASM_MACH_GENERIC_IDE_H
+#define __ASM_MACH_GENERIC_IDE_H
+
+#ifdef __KERNEL__
+
+#include <linux/pci.h>
+#include <linux/stddef.h>
+#include <asm/processor.h>
+
+/* MIPS port and memory-mapped I/O string operations.  */
+static inline void __ide_flush_prologue(void)
+{
+#ifdef CONFIG_SMP
+	if (cpu_has_dc_aliases || !cpu_has_ic_fills_f_dc)
+		preempt_disable();
+#endif
+}
+
+static inline void __ide_flush_epilogue(void)
+{
+#ifdef CONFIG_SMP
+	if (cpu_has_dc_aliases || !cpu_has_ic_fills_f_dc)
+		preempt_enable();
+#endif
+}
+
+static inline void __ide_flush_dcache_range(unsigned long addr, unsigned long size)
+{
+	if (cpu_has_dc_aliases || !cpu_has_ic_fills_f_dc) {
+		unsigned long end = addr + size;
+
+		while (addr < end) {
+			local_flush_data_cache_page((void *)addr);
+			addr += PAGE_SIZE;
+		}
+	}
+}
+
+/*
+ * insw() and gang might be called with interrupts disabled, so we can't
+ * send IPIs for flushing due to the potencial of deadlocks, see the comment
+ * above smp_call_function() in arch/mips/kernel/smp.c.	 We work around the
+ * problem by disabling preemption so we know we actually perform the flush
+ * on the processor that actually has the lines to be flushed which hopefully
+ * is even better for performance anyway.
+ */
+static inline void __ide_insw(unsigned long port, void *addr,
+	unsigned int count)
+{
+	__ide_flush_prologue();
+	insw(port, addr, count);
+	__ide_flush_dcache_range((unsigned long)addr, count * 2);
+	__ide_flush_epilogue();
+}
+
+static inline void __ide_insl(unsigned long port, void *addr, unsigned int count)
+{
+	__ide_flush_prologue();
+	insl(port, addr, count);
+	__ide_flush_dcache_range((unsigned long)addr, count * 4);
+	__ide_flush_epilogue();
+}
+
+static inline void __ide_outsw(unsigned long port, const void *addr,
+	unsigned long count)
+{
+	__ide_flush_prologue();
+	outsw(port, addr, count);
+	__ide_flush_dcache_range((unsigned long)addr, count * 2);
+	__ide_flush_epilogue();
+}
+
+static inline void __ide_outsl(unsigned long port, const void *addr,
+	unsigned long count)
+{
+	__ide_flush_prologue();
+	outsl(port, addr, count);
+	__ide_flush_dcache_range((unsigned long)addr, count * 4);
+	__ide_flush_epilogue();
+}
+
+static inline void __ide_mm_insw(void __iomem *port, void *addr, u32 count)
+{
+	__ide_flush_prologue();
+	readsw(port, addr, count);
+	__ide_flush_dcache_range((unsigned long)addr, count * 2);
+	__ide_flush_epilogue();
+}
+
+static inline void __ide_mm_insl(void __iomem *port, void *addr, u32 count)
+{
+	__ide_flush_prologue();
+	readsl(port, addr, count);
+	__ide_flush_dcache_range((unsigned long)addr, count * 4);
+	__ide_flush_epilogue();
+}
+
+static inline void __ide_mm_outsw(void __iomem *port, void *addr, u32 count)
+{
+	__ide_flush_prologue();
+	writesw(port, addr, count);
+	__ide_flush_dcache_range((unsigned long)addr, count * 2);
+	__ide_flush_epilogue();
+}
+
+static inline void __ide_mm_outsl(void __iomem * port, void *addr, u32 count)
+{
+	__ide_flush_prologue();
+	writesl(port, addr, count);
+	__ide_flush_dcache_range((unsigned long)addr, count * 4);
+	__ide_flush_epilogue();
+}
+
+/* ide_insw calls insw, not __ide_insw.	 Why? */
+#undef insw
+#undef insl
+#undef outsw
+#undef outsl
+#define insw(port, addr, count) __ide_insw(port, addr, count)
+#define insl(port, addr, count) __ide_insl(port, addr, count)
+#define outsw(port, addr, count) __ide_outsw(port, addr, count)
+#define outsl(port, addr, count) __ide_outsl(port, addr, count)
+
+#endif /* __KERNEL__ */
+
+#endif /* __ASM_MACH_GENERIC_IDE_H */
diff --git a/arch/mips/include/asm/mach-generic/ioremap.h b/arch/mips/include/asm/mach-generic/ioremap.h
new file mode 100644
index 000000000..f2442b845
--- /dev/null
+++ b/arch/mips/include/asm/mach-generic/ioremap.h
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ *	include/asm-mips/mach-generic/ioremap.h
+ */
+#ifndef __ASM_MACH_GENERIC_IOREMAP_H
+#define __ASM_MACH_GENERIC_IOREMAP_H
+
+#include <linux/types.h>
+
+static inline void __iomem *plat_ioremap(phys_addr_t offset, unsigned long size,
+	unsigned long flags)
+{
+	return NULL;
+}
+
+static inline int plat_iounmap(const volatile void __iomem *addr)
+{
+	return 0;
+}
+
+#endif /* __ASM_MACH_GENERIC_IOREMAP_H */
diff --git a/arch/mips/include/asm/mach-generic/irq.h b/arch/mips/include/asm/mach-generic/irq.h
new file mode 100644
index 000000000..4249af4be
--- /dev/null
+++ b/arch/mips/include/asm/mach-generic/irq.h
@@ -0,0 +1,33 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003 by Ralf Baechle
+ */
+#ifndef __ASM_MACH_GENERIC_IRQ_H
+#define __ASM_MACH_GENERIC_IRQ_H
+
+#ifndef NR_IRQS
+#define NR_IRQS 256
+#endif
+
+#ifdef CONFIG_I8259
+#ifndef I8259A_IRQ_BASE
+#define I8259A_IRQ_BASE 0
+#endif
+#endif
+
+#ifdef CONFIG_IRQ_MIPS_CPU
+
+#ifndef MIPS_CPU_IRQ_BASE
+#ifdef CONFIG_I8259
+#define MIPS_CPU_IRQ_BASE 16
+#else
+#define MIPS_CPU_IRQ_BASE 0
+#endif /* CONFIG_I8259 */
+#endif
+
+#endif /* CONFIG_IRQ_MIPS_CPU */
+
+#endif /* __ASM_MACH_GENERIC_IRQ_H */
diff --git a/arch/mips/include/asm/mach-generic/kernel-entry-init.h b/arch/mips/include/asm/mach-generic/kernel-entry-init.h
new file mode 100644
index 000000000..a229297c8
--- /dev/null
+++ b/arch/mips/include/asm/mach-generic/kernel-entry-init.h
@@ -0,0 +1,25 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2005 Embedded Alley Solutions, Inc
+ * Copyright (C) 2005 Ralf Baechle (ralf@linux-mips.org)
+ */
+#ifndef __ASM_MACH_GENERIC_KERNEL_ENTRY_H
+#define __ASM_MACH_GENERIC_KERNEL_ENTRY_H
+
+/* Intentionally empty macro, used in head.S. Override in
+ * arch/mips/mach-xxx/kernel-entry-init.h when necessary.
+ */
+	.macro	kernel_entry_setup
+	.endm
+
+/*
+ * Do SMP slave processor setup necessary before we can safely execute C code.
+ */
+	.macro	smp_slave_setup
+	.endm
+
+
+#endif /* __ASM_MACH_GENERIC_KERNEL_ENTRY_H */
diff --git a/arch/mips/include/asm/mach-generic/kmalloc.h b/arch/mips/include/asm/mach-generic/kmalloc.h
new file mode 100644
index 000000000..649a98338
--- /dev/null
+++ b/arch/mips/include/asm/mach-generic/kmalloc.h
@@ -0,0 +1,13 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_MACH_GENERIC_KMALLOC_H
+#define __ASM_MACH_GENERIC_KMALLOC_H
+
+#ifdef CONFIG_DMA_NONCOHERENT
+/*
+ * Total overkill for most systems but need as a safe default.
+ * Set this one if any device in the system might do non-coherent DMA.
+ */
+#define ARCH_DMA_MINALIGN	128
+#endif
+
+#endif /* __ASM_MACH_GENERIC_KMALLOC_H */
diff --git a/arch/mips/include/asm/mach-generic/mangle-port.h b/arch/mips/include/asm/mach-generic/mangle-port.h
new file mode 100644
index 000000000..77c65c294
--- /dev/null
+++ b/arch/mips/include/asm/mach-generic/mangle-port.h
@@ -0,0 +1,52 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003, 2004 Ralf Baechle
+ */
+#ifndef __ASM_MACH_GENERIC_MANGLE_PORT_H
+#define __ASM_MACH_GENERIC_MANGLE_PORT_H
+
+#define __swizzle_addr_b(port)	(port)
+#define __swizzle_addr_w(port)	(port)
+#define __swizzle_addr_l(port)	(port)
+#define __swizzle_addr_q(port)	(port)
+
+/*
+ * Sane hardware offers swapping of PCI/ISA I/O space accesses in hardware;
+ * less sane hardware forces software to fiddle with this...
+ *
+ * Regardless, if the host bus endianness mismatches that of PCI/ISA, then
+ * you can't have the numerical value of data and byte addresses within
+ * multibyte quantities both preserved at the same time.  Hence two
+ * variations of functions: non-prefixed ones that preserve the value
+ * and prefixed ones that preserve byte addresses.  The latters are
+ * typically used for moving raw data between a peripheral and memory (cf.
+ * string I/O functions), hence the "__mem_" prefix.
+ */
+#if defined(CONFIG_SWAP_IO_SPACE)
+
+# define ioswabb(a, x)		(x)
+# define __mem_ioswabb(a, x)	(x)
+# define ioswabw(a, x)		le16_to_cpu((__force __le16)(x))
+# define __mem_ioswabw(a, x)	(x)
+# define ioswabl(a, x)		le32_to_cpu((__force __le32)(x))
+# define __mem_ioswabl(a, x)	(x)
+# define ioswabq(a, x)		le64_to_cpu((__force __le64)(x))
+# define __mem_ioswabq(a, x)	(x)
+
+#else
+
+# define ioswabb(a, x)		(x)
+# define __mem_ioswabb(a, x)	(x)
+# define ioswabw(a, x)		(x)
+# define __mem_ioswabw(a, x)	((__force u16)cpu_to_le16(x))
+# define ioswabl(a, x)		(x)
+# define __mem_ioswabl(a, x)	((__force u32)cpu_to_le32(x))
+# define ioswabq(a, x)		(x)
+# define __mem_ioswabq(a, x)	((__force u64)cpu_to_le64(x))
+
+#endif
+
+#endif /* __ASM_MACH_GENERIC_MANGLE_PORT_H */
diff --git a/arch/mips/include/asm/mach-generic/mc146818rtc.h b/arch/mips/include/asm/mach-generic/mc146818rtc.h
new file mode 100644
index 000000000..9c72e540f
--- /dev/null
+++ b/arch/mips/include/asm/mach-generic/mc146818rtc.h
@@ -0,0 +1,36 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1998, 2001, 03 by Ralf Baechle
+ *
+ * RTC routines for PC style attached Dallas chip.
+ */
+#ifndef __ASM_MACH_GENERIC_MC146818RTC_H
+#define __ASM_MACH_GENERIC_MC146818RTC_H
+
+#include <asm/io.h>
+
+#define RTC_PORT(x)	(0x70 + (x))
+#define RTC_IRQ		8
+
+static inline unsigned char CMOS_READ(unsigned long addr)
+{
+	outb_p(addr, RTC_PORT(0));
+	return inb_p(RTC_PORT(1));
+}
+
+static inline void CMOS_WRITE(unsigned char data, unsigned long addr)
+{
+	outb_p(addr, RTC_PORT(0));
+	outb_p(data, RTC_PORT(1));
+}
+
+#define RTC_ALWAYS_BCD	0
+
+#ifndef mc146818_decode_year
+#define mc146818_decode_year(year) ((year) < 70 ? (year) + 2000 : (year) + 1900)
+#endif
+
+#endif /* __ASM_MACH_GENERIC_MC146818RTC_H */
diff --git a/arch/mips/include/asm/mach-generic/spaces.h b/arch/mips/include/asm/mach-generic/spaces.h
new file mode 100644
index 000000000..b247575c5
--- /dev/null
+++ b/arch/mips/include/asm/mach-generic/spaces.h
@@ -0,0 +1,98 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994 - 1999, 2000, 03, 04 Ralf Baechle
+ * Copyright (C) 2000, 2002  Maciej W. Rozycki
+ * Copyright (C) 1990, 1999, 2000 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_MACH_GENERIC_SPACES_H
+#define _ASM_MACH_GENERIC_SPACES_H
+
+#include <linux/const.h>
+
+#include <asm/mipsregs.h>
+
+#ifndef IO_SPACE_LIMIT
+#define IO_SPACE_LIMIT 0xffff
+#endif
+
+/*
+ * This gives the physical RAM offset.
+ */
+#ifndef __ASSEMBLY__
+# if defined(CONFIG_MIPS_AUTO_PFN_OFFSET)
+#  define PHYS_OFFSET		((unsigned long)PFN_PHYS(ARCH_PFN_OFFSET))
+# elif !defined(PHYS_OFFSET)
+#  define PHYS_OFFSET		_AC(0, UL)
+# endif
+#endif /* __ASSEMBLY__ */
+
+#ifdef CONFIG_32BIT
+#define CAC_BASE		_AC(0x80000000, UL)
+#ifndef IO_BASE
+#define IO_BASE			_AC(0xa0000000, UL)
+#endif
+#ifndef UNCAC_BASE
+#define UNCAC_BASE		_AC(0xa0000000, UL)
+#endif
+
+#ifndef MAP_BASE
+#define MAP_BASE		_AC(0xc0000000, UL)
+#endif
+
+/*
+ * Memory above this physical address will be considered highmem.
+ */
+#ifndef HIGHMEM_START
+#define HIGHMEM_START		_AC(0x20000000, UL)
+#endif
+
+#endif /* CONFIG_32BIT */
+
+#ifdef CONFIG_64BIT
+
+#ifndef CAC_BASE
+#define CAC_BASE	PHYS_TO_XKPHYS(read_c0_config() & CONF_CM_CMASK, 0)
+#endif
+
+#ifndef IO_BASE
+#define IO_BASE			_AC(0x9000000000000000, UL)
+#endif
+
+#ifndef UNCAC_BASE
+#define UNCAC_BASE		_AC(0x9000000000000000, UL)
+#endif
+
+#ifndef MAP_BASE
+#define MAP_BASE		_AC(0xc000000000000000, UL)
+#endif
+
+/*
+ * Memory above this physical address will be considered highmem.
+ * Fixme: 59 bits is a fictive number and makes assumptions about processors
+ * in the distant future.  Nobody will care for a few years :-)
+ */
+#ifndef HIGHMEM_START
+#define HIGHMEM_START		(_AC(1, UL) << _AC(59, UL))
+#endif
+
+#define TO_PHYS(x)		(	      ((x) & TO_PHYS_MASK))
+#define TO_CAC(x)		(CAC_BASE   | ((x) & TO_PHYS_MASK))
+#define TO_UNCAC(x)		(UNCAC_BASE | ((x) & TO_PHYS_MASK))
+
+#endif /* CONFIG_64BIT */
+
+/*
+ * This handles the memory map.
+ */
+#ifndef PAGE_OFFSET
+#define PAGE_OFFSET		(CAC_BASE + PHYS_OFFSET)
+#endif
+
+#ifndef FIXADDR_TOP
+#define FIXADDR_TOP		((unsigned long)(long)(int)0xfffe0000)
+#endif
+
+#endif /* __ASM_MACH_GENERIC_SPACES_H */
diff --git a/arch/mips/include/asm/mach-generic/topology.h b/arch/mips/include/asm/mach-generic/topology.h
new file mode 100644
index 000000000..5428f333a
--- /dev/null
+++ b/arch/mips/include/asm/mach-generic/topology.h
@@ -0,0 +1 @@
+#include <asm-generic/topology.h>
diff --git a/arch/mips/include/asm/mach-ingenic/cpu-feature-overrides.h b/arch/mips/include/asm/mach-ingenic/cpu-feature-overrides.h
new file mode 100644
index 000000000..7ace50127
--- /dev/null
+++ b/arch/mips/include/asm/mach-ingenic/cpu-feature-overrides.h
@@ -0,0 +1,49 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ */
+#ifndef __ASM_MACH_JZ4740_CPU_FEATURE_OVERRIDES_H
+#define __ASM_MACH_JZ4740_CPU_FEATURE_OVERRIDES_H
+
+#define cpu_has_tlb 1
+#define cpu_has_4kex		1
+#define cpu_has_3k_cache	0
+#define cpu_has_4k_cache	1
+#define cpu_has_counter		0
+#define cpu_has_watch		1
+#define cpu_has_divec		1
+#define cpu_has_vce		0
+#define cpu_has_cache_cdex_p	0
+#define cpu_has_cache_cdex_s	0
+#define cpu_has_prefetch	1
+#define cpu_has_mcheck 1
+#define cpu_has_ejtag 1
+#define cpu_has_llsc		1
+#define cpu_has_mips16 0
+#define cpu_has_mips16e2	0
+#define cpu_has_mdmx 0
+#define cpu_has_mips3d 0
+#define cpu_has_smartmips 0
+#define kernel_uses_llsc	1
+#define cpu_has_vtag_icache	1
+#define cpu_has_dc_aliases	0
+#define cpu_has_ic_fills_f_dc	0
+#define cpu_has_pindexed_dcache 0
+#define cpu_has_mips32r1	1
+#define cpu_has_mips64r1	0
+#define cpu_has_mips64r2	0
+#define cpu_has_dsp		0
+#define cpu_has_dsp2		0
+#define cpu_has_mipsmt		0
+#define cpu_has_userlocal	0
+#define cpu_has_nofpuex 0
+#define cpu_has_64bits		0
+#define cpu_has_64bit_zero_reg 0
+#define cpu_has_inclusive_pcaches 0
+
+#define cpu_dcache_line_size()	32
+#define cpu_icache_line_size()	32
+
+#endif
diff --git a/arch/mips/include/asm/mach-ip22/cpu-feature-overrides.h b/arch/mips/include/asm/mach-ip22/cpu-feature-overrides.h
new file mode 100644
index 000000000..b80d5eafc
--- /dev/null
+++ b/arch/mips/include/asm/mach-ip22/cpu-feature-overrides.h
@@ -0,0 +1,51 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003, 07 Ralf Baechle
+ */
+#ifndef __ASM_MACH_IP22_CPU_FEATURE_OVERRIDES_H
+#define __ASM_MACH_IP22_CPU_FEATURE_OVERRIDES_H
+
+#include <asm/cpu.h>
+
+/*
+ * IP22 with a variety of processors so we can't use defaults for everything.
+ */
+#define cpu_has_tlb		1
+#define cpu_has_4kex		1
+#define cpu_has_4k_cache	1
+#define cpu_has_32fpr		1
+#define cpu_has_counter		1
+#define cpu_has_mips16		0
+#define cpu_has_mips16e2	0
+#define cpu_has_divec		0
+#define cpu_has_cache_cdex_p	1
+#define cpu_has_prefetch	0
+#define cpu_has_mcheck		0
+#define cpu_has_ejtag		0
+
+#define cpu_has_llsc		1
+#define cpu_has_vtag_icache	0		/* Needs to change for R8000 */
+#define cpu_has_dc_aliases	(PAGE_SIZE < 0x4000)
+#define cpu_has_ic_fills_f_dc	0
+
+#define cpu_has_dsp		0
+#define cpu_has_dsp2		0
+#define cpu_has_mipsmt		0
+#define cpu_has_userlocal	0
+
+#define cpu_has_nofpuex		0
+#define cpu_has_64bits		1
+
+#define cpu_has_mips_2		1
+#define cpu_has_mips_3		1
+#define cpu_has_mips_5		0
+
+#define cpu_has_mips32r1	0
+#define cpu_has_mips32r2	0
+#define cpu_has_mips64r1	0
+#define cpu_has_mips64r2	0
+
+#endif /* __ASM_MACH_IP22_CPU_FEATURE_OVERRIDES_H */
diff --git a/arch/mips/include/asm/mach-ip22/spaces.h b/arch/mips/include/asm/mach-ip22/spaces.h
new file mode 100644
index 000000000..24fe92cb5
--- /dev/null
+++ b/arch/mips/include/asm/mach-ip22/spaces.h
@@ -0,0 +1,17 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994 - 1999, 2000, 03, 04 Ralf Baechle
+ * Copyright (C) 2000, 2002  Maciej W. Rozycki
+ * Copyright (C) 1990, 1999, 2000 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_MACH_IP22_SPACES_H
+#define _ASM_MACH_IP22_SPACES_H
+
+#define PHYS_OFFSET     _AC(0x08000000, UL)
+
+#include <asm/mach-generic/spaces.h>
+
+#endif /* __ASM_MACH_IP22_SPACES_H */
diff --git a/arch/mips/include/asm/mach-ip27/cpu-feature-overrides.h b/arch/mips/include/asm/mach-ip27/cpu-feature-overrides.h
new file mode 100644
index 000000000..568fe0933
--- /dev/null
+++ b/arch/mips/include/asm/mach-ip27/cpu-feature-overrides.h
@@ -0,0 +1,75 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003, 07 Ralf Baechle
+ */
+#ifndef __ASM_MACH_IP27_CPU_FEATURE_OVERRIDES_H
+#define __ASM_MACH_IP27_CPU_FEATURE_OVERRIDES_H
+
+#include <asm/cpu.h>
+
+/*
+ * IP27 only comes with R1x000 family processors, all using the same config
+ */
+#define cpu_has_tlb			1
+#define cpu_has_tlbinv			0
+#define cpu_has_segments		0
+#define cpu_has_eva			0
+#define cpu_has_htw			0
+#define cpu_has_rixiex			0
+#define cpu_has_maar			0
+#define cpu_has_rw_llb			0
+#define cpu_has_3kex			0
+#define cpu_has_4kex			1
+#define cpu_has_3k_cache		0
+#define cpu_has_4k_cache		1
+#define cpu_has_nofpuex			0
+#define cpu_has_32fpr			1
+#define cpu_has_counter			1
+#define cpu_has_watch			1
+#define cpu_has_64bits			1
+#define cpu_has_divec			0
+#define cpu_has_vce			0
+#define cpu_has_cache_cdex_p		0
+#define cpu_has_cache_cdex_s		0
+#define cpu_has_prefetch		1
+#define cpu_has_mcheck			0
+#define cpu_has_ejtag			0
+#define cpu_has_llsc			1
+#define cpu_has_mips16			0
+#define cpu_has_mips16e2		0
+#define cpu_has_mdmx			0
+#define cpu_has_mips3d			0
+#define cpu_has_smartmips		0
+#define cpu_has_rixi			0
+#define cpu_has_xpa			0
+#define cpu_has_vtag_icache		0
+#define cpu_has_dc_aliases		0
+#define cpu_has_ic_fills_f_dc		0
+
+#define cpu_icache_snoops_remote_store	1
+
+#define cpu_has_mips32r1		0
+#define cpu_has_mips32r2		0
+#define cpu_has_mips64r1		0
+#define cpu_has_mips64r2		0
+#define cpu_has_mips32r6		0
+#define cpu_has_mips64r6		0
+
+#define cpu_has_dsp			0
+#define cpu_has_dsp2			0
+#define cpu_has_mipsmt			0
+#define cpu_has_userlocal		0
+#define cpu_has_inclusive_pcaches	1
+#define cpu_has_perf_cntr_intr_bit	0
+#define cpu_has_vz			0
+#define cpu_has_fre			0
+#define cpu_has_cdmm			0
+
+#define cpu_dcache_line_size()		32
+#define cpu_icache_line_size()		64
+#define cpu_scache_line_size()		128
+
+#endif /* __ASM_MACH_IP27_CPU_FEATURE_OVERRIDES_H */
diff --git a/arch/mips/include/asm/mach-ip27/irq.h b/arch/mips/include/asm/mach-ip27/irq.h
new file mode 100644
index 000000000..f45d7999f
--- /dev/null
+++ b/arch/mips/include/asm/mach-ip27/irq.h
@@ -0,0 +1,24 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1999, 2000, 01, 02, 03 by Ralf Baechle
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ * Copyright (C) 2001 Kanoj Sarcar
+ */
+#ifndef __ASM_MACH_IP27_IRQ_H
+#define __ASM_MACH_IP27_IRQ_H
+
+#define NR_IRQS 256
+
+#include <asm/mach-generic/irq.h>
+
+#define IP27_HUB_PEND0_IRQ	(MIPS_CPU_IRQ_BASE + 2)
+#define IP27_HUB_PEND1_IRQ	(MIPS_CPU_IRQ_BASE + 3)
+#define IP27_RT_TIMER_IRQ	(MIPS_CPU_IRQ_BASE + 4)
+
+#define IP27_HUB_IRQ_BASE	(MIPS_CPU_IRQ_BASE + 8)
+#define IP27_HUB_IRQ_COUNT	128
+
+#endif /* __ASM_MACH_IP27_IRQ_H */
diff --git a/arch/mips/include/asm/mach-ip27/kernel-entry-init.h b/arch/mips/include/asm/mach-ip27/kernel-entry-init.h
new file mode 100644
index 000000000..3e54f605a
--- /dev/null
+++ b/arch/mips/include/asm/mach-ip27/kernel-entry-init.h
@@ -0,0 +1,96 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2000 Silicon Graphics, Inc.
+ * Copyright (C) 2005 Ralf Baechle <ralf@linux-mips.org>
+ */
+#ifndef __ASM_MACH_IP27_KERNEL_ENTRY_H
+#define __ASM_MACH_IP27_KERNEL_ENTRY_H
+
+#include <asm/sn/addrs.h>
+#include <asm/sn/agent.h>
+#include <asm/sn/klkernvars.h>
+
+/*
+ * TLB bits
+ */
+#define PAGE_GLOBAL		(1 << 6)
+#define PAGE_VALID		(1 << 7)
+#define PAGE_DIRTY		(1 << 8)
+#define CACHE_CACHABLE_COW	(5 << 9)
+
+	/*
+	 * inputs are the text nasid in t1, data nasid in t2.
+	 */
+	.macro MAPPED_KERNEL_SETUP_TLB
+#ifdef CONFIG_MAPPED_KERNEL
+	/*
+	 * This needs to read the nasid - assume 0 for now.
+	 * Drop in 0xffffffffc0000000 in tlbhi, 0+VG in tlblo_0,
+	 * 0+DVG in tlblo_1.
+	 */
+	dli	t0, 0xffffffffc0000000
+	dmtc0	t0, CP0_ENTRYHI
+	li	t0, 0x1c000		# Offset of text into node memory
+	dsll	t1, NASID_SHFT		# Shift text nasid into place
+	dsll	t2, NASID_SHFT		# Same for data nasid
+	or	t1, t1, t0		# Physical load address of kernel text
+	or	t2, t2, t0		# Physical load address of kernel data
+	dsrl	t1, 12			# 4K pfn
+	dsrl	t2, 12			# 4K pfn
+	dsll	t1, 6			# Get pfn into place
+	dsll	t2, 6			# Get pfn into place
+	li	t0, ((PAGE_GLOBAL | PAGE_VALID | CACHE_CACHABLE_COW) >> 6)
+	or	t0, t0, t1
+	mtc0	t0, CP0_ENTRYLO0	# physaddr, VG, cach exlwr
+	li	t0, ((PAGE_GLOBAL | PAGE_VALID |  PAGE_DIRTY | CACHE_CACHABLE_COW) >> 6)
+	or	t0, t0, t2
+	mtc0	t0, CP0_ENTRYLO1	# physaddr, DVG, cach exlwr
+	li	t0, 0x1ffe000		# MAPPED_KERN_TLBMASK, TLBPGMASK_16M
+	mtc0	t0, CP0_PAGEMASK
+	li	t0, 0			# KMAP_INX
+	mtc0	t0, CP0_INDEX
+	li	t0, 1
+	mtc0	t0, CP0_WIRED
+	tlbwi
+#else
+	mtc0	zero, CP0_WIRED
+#endif
+	.endm
+
+/*
+ * Intentionally empty macro, used in head.S. Override in
+ * arch/mips/mach-xxx/kernel-entry-init.h when necessary.
+ */
+	.macro	kernel_entry_setup
+	GET_NASID_ASM	t1
+	move		t2, t1			# text and data are here
+	MAPPED_KERNEL_SETUP_TLB
+	.endm
+
+/*
+ * Do SMP slave processor setup necessary before we can safely execute C code.
+ */
+	.macro	smp_slave_setup
+	GET_NASID_ASM	t1
+	dli	t0, KLDIR_OFFSET + (KLI_KERN_VARS * KLDIR_ENT_SIZE) + \
+		    KLDIR_OFF_POINTER + CAC_BASE
+	dsll	t1, NASID_SHFT
+	or	t0, t0, t1
+	ld	t0, 0(t0)			# t0 points to kern_vars struct
+	lh	t1, KV_RO_NASID_OFFSET(t0)
+	lh	t2, KV_RW_NASID_OFFSET(t0)
+	MAPPED_KERNEL_SETUP_TLB
+
+	/*
+	 * We might not get launched at the address the kernel is linked to,
+	 * so we jump there.
+	 */
+	PTR_LA	t0, 0f
+	jr	t0
+0:
+	.endm
+
+#endif /* __ASM_MACH_IP27_KERNEL_ENTRY_H */
diff --git a/arch/mips/include/asm/mach-ip27/mangle-port.h b/arch/mips/include/asm/mach-ip27/mangle-port.h
new file mode 100644
index 000000000..f71c38bbf
--- /dev/null
+++ b/arch/mips/include/asm/mach-ip27/mangle-port.h
@@ -0,0 +1,25 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003, 2004 Ralf Baechle
+ */
+#ifndef __ASM_MACH_IP27_MANGLE_PORT_H
+#define __ASM_MACH_IP27_MANGLE_PORT_H
+
+#define __swizzle_addr_b(port)	((port) ^ 3)
+#define __swizzle_addr_w(port)	((port) ^ 2)
+#define __swizzle_addr_l(port)	(port)
+#define __swizzle_addr_q(port)	(port)
+
+# define ioswabb(a, x)		(x)
+# define __mem_ioswabb(a, x)	(x)
+# define ioswabw(a, x)		(x)
+# define __mem_ioswabw(a, x)	((__force u16)cpu_to_le16(x))
+# define ioswabl(a, x)		(x)
+# define __mem_ioswabl(a, x)	((__force u32)cpu_to_le32(x))
+# define ioswabq(a, x)		(x)
+# define __mem_ioswabq(a, x)	((__force u64)cpu_to_le64(x))
+
+#endif /* __ASM_MACH_IP27_MANGLE_PORT_H */
diff --git a/arch/mips/include/asm/mach-ip27/mmzone.h b/arch/mips/include/asm/mach-ip27/mmzone.h
new file mode 100644
index 000000000..08c36e50a
--- /dev/null
+++ b/arch/mips/include/asm/mach-ip27/mmzone.h
@@ -0,0 +1,28 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _ASM_MACH_MMZONE_H
+#define _ASM_MACH_MMZONE_H
+
+#include <asm/sn/addrs.h>
+#include <asm/sn/arch.h>
+#include <asm/sn/agent.h>
+#include <asm/sn/klkernvars.h>
+
+#define pa_to_nid(addr)		NASID_GET(addr)
+
+struct hub_data {
+	kern_vars_t	kern_vars;
+	DECLARE_BITMAP(h_bigwin_used, HUB_NUM_BIG_WINDOW);
+	cpumask_t	h_cpus;
+};
+
+struct node_data {
+	struct pglist_data pglist;
+	struct hub_data hub;
+};
+
+extern struct node_data *__node_data[];
+
+#define NODE_DATA(n)		(&__node_data[(n)]->pglist)
+#define hub_data(n)		(&__node_data[(n)]->hub)
+
+#endif /* _ASM_MACH_MMZONE_H */
diff --git a/arch/mips/include/asm/mach-ip27/spaces.h b/arch/mips/include/asm/mach-ip27/spaces.h
new file mode 100644
index 000000000..66421e9a6
--- /dev/null
+++ b/arch/mips/include/asm/mach-ip27/spaces.h
@@ -0,0 +1,35 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1996, 99 Ralf Baechle
+ * Copyright (C) 2000, 2002  Maciej W. Rozycki
+ * Copyright (C) 1990, 1999 by Silicon Graphics, Inc.
+ */
+#ifndef _ASM_MACH_IP27_SPACES_H
+#define _ASM_MACH_IP27_SPACES_H
+
+#include <linux/const.h>
+
+/*
+ * IP27 uses the R10000's uncached attribute feature.  Attribute 3 selects
+ * uncached memory addressing. Hide the definitions on 32-bit compilation
+ * of the compat-vdso code.
+ */
+#ifdef CONFIG_64BIT
+#define HSPEC_BASE		_AC(0x9000000000000000, UL)
+#define IO_BASE			_AC(0x9200000000000000, UL)
+#define MSPEC_BASE		_AC(0x9400000000000000, UL)
+#define UNCAC_BASE		_AC(0x9600000000000000, UL)
+#define CAC_BASE		_AC(0xa800000000000000, UL)
+#endif
+
+#define TO_MSPEC(x)		(MSPEC_BASE | ((x) & TO_PHYS_MASK))
+#define TO_HSPEC(x)		(HSPEC_BASE | ((x) & TO_PHYS_MASK))
+
+#define HIGHMEM_START		(~0UL)
+
+#include <asm/mach-generic/spaces.h>
+
+#endif /* _ASM_MACH_IP27_SPACES_H */
diff --git a/arch/mips/include/asm/mach-ip27/topology.h b/arch/mips/include/asm/mach-ip27/topology.h
new file mode 100644
index 000000000..d66cc53fe
--- /dev/null
+++ b/arch/mips/include/asm/mach-ip27/topology.h
@@ -0,0 +1,31 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _ASM_MACH_TOPOLOGY_H
+#define _ASM_MACH_TOPOLOGY_H	1
+
+#include <asm/sn/types.h>
+#include <asm/mmzone.h>
+
+struct cpuinfo_ip27 {
+	nasid_t		p_nasid;	/* my node ID in numa-as-id-space */
+	unsigned short	p_speed;	/* cpu speed in MHz */
+	unsigned char	p_slice;	/* Physical position on node board */
+};
+
+extern struct cpuinfo_ip27 sn_cpu_info[NR_CPUS];
+
+#define cpu_to_node(cpu)	(cputonasid(cpu))
+#define cpumask_of_node(node)	((node) == -1 ?				\
+				 cpu_all_mask :				\
+				 &hub_data(node)->h_cpus)
+struct pci_bus;
+extern int pcibus_to_node(struct pci_bus *);
+
+#define cpumask_of_pcibus(bus)	(cpumask_of_node(pcibus_to_node(bus)))
+
+extern unsigned char __node_distances[MAX_NUMNODES][MAX_NUMNODES];
+
+#define node_distance(from, to) (__node_distances[(from)][(to)])
+
+#include <asm-generic/topology.h>
+
+#endif /* _ASM_MACH_TOPOLOGY_H */
diff --git a/arch/mips/include/asm/mach-ip28/cpu-feature-overrides.h b/arch/mips/include/asm/mach-ip28/cpu-feature-overrides.h
new file mode 100644
index 000000000..613bbc10c
--- /dev/null
+++ b/arch/mips/include/asm/mach-ip28/cpu-feature-overrides.h
@@ -0,0 +1,54 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003 Ralf Baechle
+ * 6/2004	pf
+ */
+#ifndef __ASM_MACH_IP28_CPU_FEATURE_OVERRIDES_H
+#define __ASM_MACH_IP28_CPU_FEATURE_OVERRIDES_H
+
+#include <asm/cpu.h>
+
+/*
+ * IP28 only comes with R10000 family processors all using the same config
+ */
+#define cpu_has_watch		1
+#define cpu_has_mips16		0
+#define cpu_has_mips16e2	0
+#define cpu_has_divec		0
+#define cpu_has_vce		0
+#define cpu_has_cache_cdex_p	0
+#define cpu_has_cache_cdex_s	0
+#define cpu_has_prefetch	1
+#define cpu_has_mcheck		0
+#define cpu_has_ejtag		0
+
+#define cpu_has_llsc		0
+#define cpu_has_vtag_icache	0
+#define cpu_has_dc_aliases	0 /* see probe_pcache() */
+#define cpu_has_ic_fills_f_dc	0
+#define cpu_has_dsp		0
+#define cpu_has_dsp2		0
+#define cpu_icache_snoops_remote_store	1
+#define cpu_has_mipsmt		0
+#define cpu_has_userlocal	0
+
+#define cpu_has_nofpuex		0
+#define cpu_has_64bits		1
+
+#define cpu_has_4kex		1
+#define cpu_has_4k_cache	1
+
+#define cpu_has_inclusive_pcaches	1
+
+#define cpu_dcache_line_size()	32
+#define cpu_icache_line_size()	64
+
+#define cpu_has_mips32r1	0
+#define cpu_has_mips32r2	0
+#define cpu_has_mips64r1	0
+#define cpu_has_mips64r2	0
+
+#endif /* __ASM_MACH_IP28_CPU_FEATURE_OVERRIDES_H */
diff --git a/arch/mips/include/asm/mach-ip28/spaces.h b/arch/mips/include/asm/mach-ip28/spaces.h
new file mode 100644
index 000000000..c4a912733
--- /dev/null
+++ b/arch/mips/include/asm/mach-ip28/spaces.h
@@ -0,0 +1,18 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994 - 1999, 2000, 03, 04 Ralf Baechle
+ * Copyright (C) 2000, 2002  Maciej W. Rozycki
+ * Copyright (C) 1990, 1999, 2000 Silicon Graphics, Inc.
+ * 2004 pf
+ */
+#ifndef _ASM_MACH_IP28_SPACES_H
+#define _ASM_MACH_IP28_SPACES_H
+
+#define PHYS_OFFSET	_AC(0x20000000, UL)
+
+#include <asm/mach-generic/spaces.h>
+
+#endif /* _ASM_MACH_IP28_SPACES_H */
diff --git a/arch/mips/include/asm/mach-ip30/cpu-feature-overrides.h b/arch/mips/include/asm/mach-ip30/cpu-feature-overrides.h
new file mode 100644
index 000000000..ce4e4c6e0
--- /dev/null
+++ b/arch/mips/include/asm/mach-ip30/cpu-feature-overrides.h
@@ -0,0 +1,78 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * IP30/Octane cpu-features overrides.
+ *
+ * Copyright (C) 2003 Ralf Baechle <ralf@linux-mips.org>
+ *		 2004-2007 Stanislaw Skowronek <skylark@unaligned.org>
+ *		 2009 Johannes Dickgreber <tanzy@gmx.de>
+ *		 2015 Joshua Kinard <kumba@gentoo.org>
+ *
+ */
+#ifndef __ASM_MACH_IP30_CPU_FEATURE_OVERRIDES_H
+#define __ASM_MACH_IP30_CPU_FEATURE_OVERRIDES_H
+
+#include <asm/cpu.h>
+
+/*
+ * IP30 only supports R1[024]000 processors, all using the same config
+ */
+#define cpu_has_tlb			1
+#define cpu_has_tlbinv			0
+#define cpu_has_segments		0
+#define cpu_has_eva			0
+#define cpu_has_htw			0
+#define cpu_has_rixiex			0
+#define cpu_has_maar			0
+#define cpu_has_rw_llb			0
+#define cpu_has_3kex			0
+#define cpu_has_4kex			1
+#define cpu_has_3k_cache		0
+#define cpu_has_4k_cache		1
+#define cpu_has_nofpuex			0
+#define cpu_has_32fpr			1
+#define cpu_has_counter			1
+#define cpu_has_watch			1
+#define cpu_has_64bits			1
+#define cpu_has_divec			0
+#define cpu_has_vce			0
+#define cpu_has_cache_cdex_p		0
+#define cpu_has_cache_cdex_s		0
+#define cpu_has_prefetch		1
+#define cpu_has_mcheck			0
+#define cpu_has_ejtag			0
+#define cpu_has_llsc			1
+#define cpu_has_mips16			0
+#define cpu_has_mdmx			0
+#define cpu_has_mips3d			0
+#define cpu_has_smartmips		0
+#define cpu_has_rixi			0
+#define cpu_has_xpa			0
+#define cpu_has_vtag_icache		0
+#define cpu_has_dc_aliases		0
+#define cpu_has_ic_fills_f_dc		0
+
+#define cpu_icache_snoops_remote_store	1
+
+#define cpu_has_mips32r1		0
+#define cpu_has_mips32r2		0
+#define cpu_has_mips64r1		0
+#define cpu_has_mips64r2		0
+#define cpu_has_mips32r6		0
+#define cpu_has_mips64r6		0
+
+#define cpu_has_dsp			0
+#define cpu_has_dsp2			0
+#define cpu_has_mipsmt			0
+#define cpu_has_userlocal		0
+#define cpu_has_inclusive_pcaches	1
+#define cpu_has_perf_cntr_intr_bit	0
+#define cpu_has_vz			0
+#define cpu_has_fre			0
+#define cpu_has_cdmm			0
+
+#define cpu_dcache_line_size()		32
+#define cpu_icache_line_size()		64
+#define cpu_scache_line_size()		128
+
+#endif /* __ASM_MACH_IP30_CPU_FEATURE_OVERRIDES_H */
+
diff --git a/arch/mips/include/asm/mach-ip30/kernel-entry-init.h b/arch/mips/include/asm/mach-ip30/kernel-entry-init.h
new file mode 100644
index 000000000..be0472c97
--- /dev/null
+++ b/arch/mips/include/asm/mach-ip30/kernel-entry-init.h
@@ -0,0 +1,13 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifndef __ASM_MACH_IP30_KERNEL_ENTRY_H
+#define __ASM_MACH_IP30_KERNEL_ENTRY_H
+
+	.macro  kernel_entry_setup
+	.endm
+
+	.macro	smp_slave_setup
+	move	gp, a0
+	.endm
+
+#endif /* __ASM_MACH_IP30_KERNEL_ENTRY_H */
diff --git a/arch/mips/include/asm/mach-ip30/mangle-port.h b/arch/mips/include/asm/mach-ip30/mangle-port.h
new file mode 100644
index 000000000..439c6a601
--- /dev/null
+++ b/arch/mips/include/asm/mach-ip30/mangle-port.h
@@ -0,0 +1,22 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2003, 2004 Ralf Baechle
+ */
+#ifndef __ASM_MACH_IP30_MANGLE_PORT_H
+#define __ASM_MACH_IP30_MANGLE_PORT_H
+
+#define __swizzle_addr_b(port)	((port)^3)
+#define __swizzle_addr_w(port)	((port)^2)
+#define __swizzle_addr_l(port)	(port)
+#define __swizzle_addr_q(port)	(port)
+
+#define ioswabb(a, x)		(x)
+#define __mem_ioswabb(a, x)	(x)
+#define ioswabw(a, x)		(x)
+#define __mem_ioswabw(a, x)	((__force u16)cpu_to_le16(x))
+#define ioswabl(a, x)		(x)
+#define __mem_ioswabl(a, x)	((__force u32)cpu_to_le32(x))
+#define ioswabq(a, x)		(x)
+#define __mem_ioswabq(a, x)	((__force u64)cpu_to_le64(x))
+
+#endif /* __ASM_MACH_IP30_MANGLE_PORT_H */
diff --git a/arch/mips/include/asm/mach-ip30/spaces.h b/arch/mips/include/asm/mach-ip30/spaces.h
new file mode 100644
index 000000000..c8a302dfb
--- /dev/null
+++ b/arch/mips/include/asm/mach-ip30/spaces.h
@@ -0,0 +1,20 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2016 Joshua Kinard <kumba@gentoo.org>
+ *
+ */
+#ifndef _ASM_MACH_IP30_SPACES_H
+#define _ASM_MACH_IP30_SPACES_H
+
+/*
+ * Memory in IP30/Octane is offset 512MB in the physical address space.
+ */
+#define PHYS_OFFSET	_AC(0x20000000, UL)
+
+#ifdef CONFIG_64BIT
+#define CAC_BASE	_AC(0xA800000000000000, UL)
+#endif
+
+#include <asm/mach-generic/spaces.h>
+
+#endif /* _ASM_MACH_IP30_SPACES_H */
diff --git a/arch/mips/include/asm/mach-ip32/cpu-feature-overrides.h b/arch/mips/include/asm/mach-ip32/cpu-feature-overrides.h
new file mode 100644
index 000000000..63b4c8890
--- /dev/null
+++ b/arch/mips/include/asm/mach-ip32/cpu-feature-overrides.h
@@ -0,0 +1,51 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2005 Ilya A. Volynets-Evenbakh
+ * Copyright (C) 2005, 07 Ralf Baechle (ralf@linux-mips.org)
+ */
+#ifndef __ASM_MACH_IP32_CPU_FEATURE_OVERRIDES_H
+#define __ASM_MACH_IP32_CPU_FEATURE_OVERRIDES_H
+
+
+/*
+ * R5000 has an interesting "restriction":  ll(d)/sc(d)
+ * instructions to XKPHYS region simply do uncached bus
+ * requests. This breaks all the atomic bitops functions.
+ * so, for 64bit IP32 kernel we just don't use ll/sc.
+ * This does not affect luserland.
+ */
+#if (defined(CONFIG_CPU_R5000) || defined(CONFIG_CPU_NEVADA)) && defined(CONFIG_64BIT)
+#define cpu_has_llsc		0
+#else
+#define cpu_has_llsc		1
+#endif
+
+/* Settings which are common for all ip32 CPUs */
+#define cpu_has_tlb		1
+#define cpu_has_4kex		1
+#define cpu_has_32fpr		1
+#define cpu_has_counter		1
+#define cpu_has_mips16		0
+#define cpu_has_mips16e2	0
+#define cpu_has_vce		0
+#define cpu_has_cache_cdex_s	0
+#define cpu_has_mcheck		0
+#define cpu_has_ejtag		0
+#define cpu_has_vtag_icache	0
+#define cpu_has_ic_fills_f_dc	0
+#define cpu_has_dsp		0
+#define cpu_has_dsp2		0
+#define cpu_has_4k_cache	1
+#define cpu_has_mipsmt		0
+#define cpu_has_userlocal	0
+
+
+#define cpu_has_mips32r1	0
+#define cpu_has_mips32r2	0
+#define cpu_has_mips64r1	0
+#define cpu_has_mips64r2	0
+
+#endif /* __ASM_MACH_IP32_CPU_FEATURE_OVERRIDES_H */
diff --git a/arch/mips/include/asm/mach-ip32/kmalloc.h b/arch/mips/include/asm/mach-ip32/kmalloc.h
new file mode 100644
index 000000000..07a0146ea
--- /dev/null
+++ b/arch/mips/include/asm/mach-ip32/kmalloc.h
@@ -0,0 +1,12 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_MACH_IP32_KMALLOC_H
+#define __ASM_MACH_IP32_KMALLOC_H
+
+
+#if defined(CONFIG_CPU_R5000) || defined(CONFIG_CPU_RM7000)
+#define ARCH_DMA_MINALIGN	32
+#else
+#define ARCH_DMA_MINALIGN	128
+#endif
+
+#endif /* __ASM_MACH_IP32_KMALLOC_H */
diff --git a/arch/mips/include/asm/mach-ip32/mangle-port.h b/arch/mips/include/asm/mach-ip32/mangle-port.h
new file mode 100644
index 000000000..4bc3d20e8
--- /dev/null
+++ b/arch/mips/include/asm/mach-ip32/mangle-port.h
@@ -0,0 +1,26 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003 Ladislav Michl
+ * Copyright (C) 2004 Ralf Baechle
+ */
+#ifndef __ASM_MACH_IP32_MANGLE_PORT_H
+#define __ASM_MACH_IP32_MANGLE_PORT_H
+
+#define __swizzle_addr_b(port)	((port) ^ 3)
+#define __swizzle_addr_w(port)	((port) ^ 2)
+#define __swizzle_addr_l(port)	(port)
+#define __swizzle_addr_q(port)	(port)
+
+# define ioswabb(a, x)		(x)
+# define __mem_ioswabb(a, x)	(x)
+# define ioswabw(a, x)		(x)
+# define __mem_ioswabw(a, x)	((__force u16)cpu_to_le16(x))
+# define ioswabl(a, x)		(x)
+# define __mem_ioswabl(a, x)	((__force u32)cpu_to_le32(x))
+# define ioswabq(a, x)		(x)
+# define __mem_ioswabq(a, x)	((__force u64)cpu_to_le64(x))
+
+#endif /* __ASM_MACH_IP32_MANGLE_PORT_H */
diff --git a/arch/mips/include/asm/mach-jazz/floppy.h b/arch/mips/include/asm/mach-jazz/floppy.h
new file mode 100644
index 000000000..294ebb834
--- /dev/null
+++ b/arch/mips/include/asm/mach-jazz/floppy.h
@@ -0,0 +1,133 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1998, 2003 by Ralf Baechle
+ */
+#ifndef __ASM_MACH_JAZZ_FLOPPY_H
+#define __ASM_MACH_JAZZ_FLOPPY_H
+
+#include <linux/delay.h>
+#include <linux/linkage.h>
+#include <linux/types.h>
+#include <linux/mm.h>
+#include <asm/addrspace.h>
+#include <asm/jazz.h>
+#include <asm/jazzdma.h>
+
+static inline unsigned char fd_inb(unsigned int base, unsigned int reg)
+{
+	unsigned char c;
+
+	c = *(volatile unsigned char *) (base + reg);
+	udelay(1);
+
+	return c;
+}
+
+static inline void fd_outb(unsigned char value, unsigned int base, unsigned int reg)
+{
+	*(volatile unsigned char *) (base + reg) = value;
+}
+
+/*
+ * How to access the floppy DMA functions.
+ */
+static inline void fd_enable_dma(void)
+{
+	vdma_enable(JAZZ_FLOPPY_DMA);
+}
+
+static inline void fd_disable_dma(void)
+{
+	vdma_disable(JAZZ_FLOPPY_DMA);
+}
+
+static inline int fd_request_dma(void)
+{
+	return 0;
+}
+
+static inline void fd_free_dma(void)
+{
+}
+
+static inline void fd_clear_dma_ff(void)
+{
+}
+
+static inline void fd_set_dma_mode(char mode)
+{
+	vdma_set_mode(JAZZ_FLOPPY_DMA, mode);
+}
+
+static inline void fd_set_dma_addr(char *a)
+{
+	vdma_set_addr(JAZZ_FLOPPY_DMA, vdma_phys2log(CPHYSADDR((unsigned long)a)));
+}
+
+static inline void fd_set_dma_count(unsigned int count)
+{
+	vdma_set_count(JAZZ_FLOPPY_DMA, count);
+}
+
+static inline int fd_get_dma_residue(void)
+{
+	return vdma_get_residue(JAZZ_FLOPPY_DMA);
+}
+
+static inline void fd_enable_irq(void)
+{
+}
+
+static inline void fd_disable_irq(void)
+{
+}
+
+static inline int fd_request_irq(void)
+{
+	return request_irq(FLOPPY_IRQ, floppy_interrupt,
+			   0, "floppy", NULL);
+}
+
+static inline void fd_free_irq(void)
+{
+	free_irq(FLOPPY_IRQ, NULL);
+}
+
+static inline unsigned long fd_getfdaddr1(void)
+{
+	return JAZZ_FDC_BASE;
+}
+
+static inline unsigned long fd_dma_mem_alloc(unsigned long size)
+{
+	unsigned long mem;
+
+	mem = __get_dma_pages(GFP_KERNEL, get_order(size));
+	if(!mem)
+		return 0;
+	vdma_alloc(CPHYSADDR(mem), size);	/* XXX error checking */
+
+	return mem;
+}
+
+static inline void fd_dma_mem_free(unsigned long addr, unsigned long size)
+{
+	vdma_free(vdma_phys2log(CPHYSADDR(addr)));
+	free_pages(addr, get_order(size));
+}
+
+static inline unsigned long fd_drive_type(unsigned long n)
+{
+	/* XXX This is wrong for machines with ED 2.88mb disk drives like the
+	   Olivetti M700.  Anyway, we should suck this from the ARC
+	   firmware.  */
+	if (n == 0)
+		return 4;	/* 3,5", 1.44mb */
+
+	return 0;
+}
+
+#endif /* __ASM_MACH_JAZZ_FLOPPY_H */
diff --git a/arch/mips/include/asm/mach-jazz/mc146818rtc.h b/arch/mips/include/asm/mach-jazz/mc146818rtc.h
new file mode 100644
index 000000000..987f727af
--- /dev/null
+++ b/arch/mips/include/asm/mach-jazz/mc146818rtc.h
@@ -0,0 +1,38 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1998, 2001, 03 by Ralf Baechle
+ * Copyright (C) 2007 Thomas Bogendoerfer
+ *
+ * RTC routines for Jazz style attached Dallas chip.
+ */
+#ifndef __ASM_MACH_JAZZ_MC146818RTC_H
+#define __ASM_MACH_JAZZ_MC146818RTC_H
+
+#include <linux/delay.h>
+
+#include <asm/io.h>
+#include <asm/jazz.h>
+
+#define RTC_PORT(x)	(0x70 + (x))
+#define RTC_IRQ		8
+
+static inline unsigned char CMOS_READ(unsigned long addr)
+{
+	outb_p(addr, RTC_PORT(0));
+	return *(volatile char *)JAZZ_RTC_BASE;
+}
+
+static inline void CMOS_WRITE(unsigned char data, unsigned long addr)
+{
+	outb_p(addr, RTC_PORT(0));
+	*(volatile char *)JAZZ_RTC_BASE = data;
+}
+
+#define RTC_ALWAYS_BCD	0
+
+#define mc146818_decode_year(year) ((year) + 1980)
+
+#endif /* __ASM_MACH_JAZZ_MC146818RTC_H */
diff --git a/arch/mips/include/asm/mach-lantiq/falcon/cpu-feature-overrides.h b/arch/mips/include/asm/mach-lantiq/falcon/cpu-feature-overrides.h
new file mode 100644
index 000000000..22607e61e
--- /dev/null
+++ b/arch/mips/include/asm/mach-lantiq/falcon/cpu-feature-overrides.h
@@ -0,0 +1,52 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *  Lantiq FALCON specific CPU feature overrides
+ *
+ *  Copyright (C) 2013 Thomas Langer, Lantiq Deutschland
+ *
+ *  This file was derived from: include/asm-mips/cpu-features.h
+ *	Copyright (C) 2003, 2004 Ralf Baechle
+ *	Copyright (C) 2004 Maciej W. Rozycki
+ */
+#ifndef __ASM_MACH_FALCON_CPU_FEATURE_OVERRIDES_H
+#define __ASM_MACH_FALCON_CPU_FEATURE_OVERRIDES_H
+
+#define cpu_has_tlb		1
+#define cpu_has_4kex		1
+#define cpu_has_3k_cache	0
+#define cpu_has_4k_cache	1
+#define cpu_has_sb1_cache	0
+#define cpu_has_fpu		0
+#define cpu_has_32fpr		0
+#define cpu_has_counter		1
+#define cpu_has_watch		1
+#define cpu_has_divec		1
+
+#define cpu_has_prefetch	1
+#define cpu_has_ejtag		1
+#define cpu_has_llsc		1
+
+#define cpu_has_mips16		1
+#define cpu_has_mdmx		0
+#define cpu_has_mips3d		0
+#define cpu_has_smartmips	0
+
+#define cpu_has_mips32r1	1
+#define cpu_has_mips32r2	1
+#define cpu_has_mips64r1	0
+#define cpu_has_mips64r2	0
+
+#define cpu_has_dsp		1
+#define cpu_has_mipsmt		1
+
+#define cpu_has_vint		1
+#define cpu_has_veic		1
+
+#define cpu_has_64bits		0
+#define cpu_has_64bit_zero_reg	0
+#define cpu_has_64bit_gp_regs	0
+
+#define cpu_dcache_line_size()	32
+#define cpu_icache_line_size()	32
+
+#endif /* __ASM_MACH_FALCON_CPU_FEATURE_OVERRIDES_H */
diff --git a/arch/mips/include/asm/mach-lantiq/falcon/falcon_irq.h b/arch/mips/include/asm/mach-lantiq/falcon/falcon_irq.h
new file mode 100644
index 000000000..6eeda90f7
--- /dev/null
+++ b/arch/mips/include/asm/mach-lantiq/falcon/falcon_irq.h
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *
+ *  Copyright (C) 2010 Thomas Langer <thomas.langer@lantiq.com>
+ */
+
+#ifndef _FALCON_IRQ__
+#define _FALCON_IRQ__
+
+#define INT_NUM_IRQ0			8
+#define INT_NUM_IM0_IRL0		(INT_NUM_IRQ0 + 0)
+#define INT_NUM_IM1_IRL0		(INT_NUM_IM0_IRL0 + 32)
+#define INT_NUM_IM2_IRL0		(INT_NUM_IM1_IRL0 + 32)
+#define INT_NUM_IM3_IRL0		(INT_NUM_IM2_IRL0 + 32)
+#define INT_NUM_IM4_IRL0		(INT_NUM_IM3_IRL0 + 32)
+#define INT_NUM_EXTRA_START		(INT_NUM_IM4_IRL0 + 32)
+#define INT_NUM_IM_OFFSET		(INT_NUM_IM1_IRL0 - INT_NUM_IM0_IRL0)
+
+#define MAX_IM			5
+
+#endif /* _FALCON_IRQ__ */
diff --git a/arch/mips/include/asm/mach-lantiq/falcon/irq.h b/arch/mips/include/asm/mach-lantiq/falcon/irq.h
new file mode 100644
index 000000000..c14312fb0
--- /dev/null
+++ b/arch/mips/include/asm/mach-lantiq/falcon/irq.h
@@ -0,0 +1,16 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *
+ *  Copyright (C) 2011 Thomas Langer <thomas.langer@lantiq.com>
+ */
+
+#ifndef __FALCON_IRQ_H
+#define __FALCON_IRQ_H
+
+#include <falcon_irq.h>
+
+#define NR_IRQS 328
+
+#include <asm/mach-generic/irq.h>
+
+#endif
diff --git a/arch/mips/include/asm/mach-lantiq/falcon/lantiq_soc.h b/arch/mips/include/asm/mach-lantiq/falcon/lantiq_soc.h
new file mode 100644
index 000000000..5855ba1bd
--- /dev/null
+++ b/arch/mips/include/asm/mach-lantiq/falcon/lantiq_soc.h
@@ -0,0 +1,69 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *
+ * Copyright (C) 2010 John Crispin <john@phrozen.org>
+ */
+
+#ifndef _LTQ_FALCON_H__
+#define _LTQ_FALCON_H__
+
+#ifdef CONFIG_SOC_FALCON
+
+#include <linux/pinctrl/pinctrl.h>
+#include <lantiq.h>
+
+/* Chip IDs */
+#define SOC_ID_FALCON		0x01B8
+
+/* SoC Types */
+#define SOC_TYPE_FALCON		0x01
+
+/*
+ * during early_printk no ioremap possible at this early stage
+ * let's use KSEG1 instead
+ */
+#define LTQ_ASC0_BASE_ADDR	0x1E100C00
+#define LTQ_EARLY_ASC		KSEG1ADDR(LTQ_ASC0_BASE_ADDR)
+
+/* WDT */
+#define LTQ_RST_CAUSE_WDTRST	0x0002
+
+/* CHIP ID */
+#define LTQ_STATUS_BASE_ADDR	0x1E802000
+
+#define FALCON_CHIPID		((u32 *)(KSEG1 + LTQ_STATUS_BASE_ADDR + 0x0c))
+#define FALCON_CHIPTYPE		((u32 *)(KSEG1 + LTQ_STATUS_BASE_ADDR + 0x38))
+#define FALCON_CHIPCONF		((u32 *)(KSEG1 + LTQ_STATUS_BASE_ADDR + 0x40))
+
+/* SYSCTL - start/stop/restart/configure/... different parts of the Soc */
+#define SYSCTL_SYS1		0
+#define SYSCTL_SYSETH		1
+#define SYSCTL_SYSGPE		2
+
+/* BOOT_SEL - find what boot media we have */
+#define BS_FLASH		0x1
+#define BS_SPI			0x4
+
+/* global register ranges */
+extern __iomem void *ltq_ebu_membase;
+extern __iomem void *ltq_sys1_membase;
+#define ltq_ebu_w32(x, y)	ltq_w32((x), ltq_ebu_membase + (y))
+#define ltq_ebu_r32(x)		ltq_r32(ltq_ebu_membase + (x))
+
+#define ltq_sys1_w32(x, y)	ltq_w32((x), ltq_sys1_membase + (y))
+#define ltq_sys1_r32(x)		ltq_r32(ltq_sys1_membase + (x))
+#define ltq_sys1_w32_mask(clear, set, reg)   \
+	ltq_sys1_w32((ltq_sys1_r32(reg) & ~(clear)) | (set), reg)
+
+/* allow the gpio and pinctrl drivers to talk to eachother */
+extern int pinctrl_falcon_get_range_size(int id);
+extern void pinctrl_falcon_add_gpio_range(struct pinctrl_gpio_range *range);
+
+/*
+ * to keep the irq code generic we need to define this to 0 as falcon
+ * has no EIU/EBU
+ */
+#define LTQ_EBU_PCC_ISTAT	0
+
+#endif /* CONFIG_SOC_FALCON */
+#endif /* _LTQ_XWAY_H__ */
diff --git a/arch/mips/include/asm/mach-lantiq/lantiq.h b/arch/mips/include/asm/mach-lantiq/lantiq.h
new file mode 100644
index 000000000..6ceb0287d
--- /dev/null
+++ b/arch/mips/include/asm/mach-lantiq/lantiq.h
@@ -0,0 +1,55 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *
+ *  Copyright (C) 2010 John Crispin <john@phrozen.org>
+ */
+#ifndef _LANTIQ_H__
+#define _LANTIQ_H__
+
+#include <linux/irq.h>
+#include <linux/device.h>
+#include <linux/clk.h>
+
+/* generic reg access functions */
+#define ltq_r32(reg)		__raw_readl(reg)
+#define ltq_w32(val, reg)	__raw_writel(val, reg)
+#define ltq_w32_mask(clear, set, reg)	\
+	ltq_w32((ltq_r32(reg) & ~(clear)) | (set), reg)
+#define ltq_r8(reg)		__raw_readb(reg)
+#define ltq_w8(val, reg)	__raw_writeb(val, reg)
+
+/* register access macros for EBU and CGU */
+#define ltq_ebu_w32(x, y)	ltq_w32((x), ltq_ebu_membase + (y))
+#define ltq_ebu_r32(x)		ltq_r32(ltq_ebu_membase + (x))
+#define ltq_ebu_w32_mask(x, y, z) \
+	ltq_w32_mask(x, y, ltq_ebu_membase + (z))
+extern __iomem void *ltq_ebu_membase;
+
+/* spinlock all ebu i/o */
+extern spinlock_t ebu_lock;
+
+/* some irq helpers */
+extern void ltq_disable_irq(struct irq_data *data);
+extern void ltq_mask_and_ack_irq(struct irq_data *data);
+extern void ltq_enable_irq(struct irq_data *data);
+extern int ltq_eiu_get_irq(int exin);
+
+/* clock handling */
+extern int clk_activate(struct clk *clk);
+extern void clk_deactivate(struct clk *clk);
+extern struct clk *clk_get_cpu(void);
+extern struct clk *clk_get_fpi(void);
+extern struct clk *clk_get_io(void);
+extern struct clk *clk_get_ppe(void);
+
+/* find out what bootsource we have */
+extern unsigned char ltq_boot_select(void);
+/* find out the soc type */
+extern int ltq_soc_type(void);
+
+#define IOPORT_RESOURCE_START	0x10000000
+#define IOPORT_RESOURCE_END	0xffffffff
+#define IOMEM_RESOURCE_START	0x10000000
+#define IOMEM_RESOURCE_END	0xffffffff
+
+#endif
diff --git a/arch/mips/include/asm/mach-lantiq/lantiq_platform.h b/arch/mips/include/asm/mach-lantiq/lantiq_platform.h
new file mode 100644
index 000000000..70ebb4d6f
--- /dev/null
+++ b/arch/mips/include/asm/mach-lantiq/lantiq_platform.h
@@ -0,0 +1,18 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *
+ *  Copyright (C) 2010 John Crispin <john@phrozen.org>
+ */
+
+#ifndef _LANTIQ_PLATFORM_H__
+#define _LANTIQ_PLATFORM_H__
+
+#include <linux/socket.h>
+
+/* struct used to pass info to network drivers */
+struct ltq_eth_data {
+	struct sockaddr mac;
+	int mii_mode;
+};
+
+#endif
diff --git a/arch/mips/include/asm/mach-lantiq/xway/irq.h b/arch/mips/include/asm/mach-lantiq/xway/irq.h
new file mode 100644
index 000000000..2980e7771
--- /dev/null
+++ b/arch/mips/include/asm/mach-lantiq/xway/irq.h
@@ -0,0 +1,16 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *
+ *  Copyright (C) 2010 John Crispin <john@phrozen.org>
+ */
+
+#ifndef __LANTIQ_IRQ_H
+#define __LANTIQ_IRQ_H
+
+#include <lantiq_irq.h>
+
+#define NR_IRQS 256
+
+#include <asm/mach-generic/irq.h>
+
+#endif
diff --git a/arch/mips/include/asm/mach-lantiq/xway/lantiq_irq.h b/arch/mips/include/asm/mach-lantiq/xway/lantiq_irq.h
new file mode 100644
index 000000000..5f0d0ba99
--- /dev/null
+++ b/arch/mips/include/asm/mach-lantiq/xway/lantiq_irq.h
@@ -0,0 +1,22 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *
+ *  Copyright (C) 2010 John Crispin <john@phrozen.org>
+ */
+
+#ifndef _LANTIQ_XWAY_IRQ_H__
+#define _LANTIQ_XWAY_IRQ_H__
+
+#define INT_NUM_IRQ0		8
+#define INT_NUM_IM0_IRL0	(INT_NUM_IRQ0 + 0)
+#define INT_NUM_IM1_IRL0	(INT_NUM_IRQ0 + 32)
+#define INT_NUM_IM2_IRL0	(INT_NUM_IRQ0 + 64)
+#define INT_NUM_IM3_IRL0	(INT_NUM_IRQ0 + 96)
+#define INT_NUM_IM4_IRL0	(INT_NUM_IRQ0 + 128)
+#define INT_NUM_IM_OFFSET	(INT_NUM_IM1_IRL0 - INT_NUM_IM0_IRL0)
+
+#define LTQ_DMA_CH0_INT		(INT_NUM_IM2_IRL0)
+
+#define MAX_IM			5
+
+#endif
diff --git a/arch/mips/include/asm/mach-lantiq/xway/lantiq_soc.h b/arch/mips/include/asm/mach-lantiq/xway/lantiq_soc.h
new file mode 100644
index 000000000..4790cfa19
--- /dev/null
+++ b/arch/mips/include/asm/mach-lantiq/xway/lantiq_soc.h
@@ -0,0 +1,106 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *
+ *  Copyright (C) 2010 John Crispin <john@phrozen.org>
+ */
+
+#ifndef _LTQ_XWAY_H__
+#define _LTQ_XWAY_H__
+
+#ifdef CONFIG_SOC_TYPE_XWAY
+
+#include <lantiq.h>
+
+/* Chip IDs */
+#define SOC_ID_DANUBE1		0x129
+#define SOC_ID_DANUBE2		0x12B
+#define SOC_ID_TWINPASS		0x12D
+#define SOC_ID_AMAZON_SE_1	0x152 /* 50601 */
+#define SOC_ID_AMAZON_SE_2	0x153 /* 50600 */
+#define SOC_ID_ARX188		0x16C
+#define SOC_ID_ARX168_1		0x16D
+#define SOC_ID_ARX168_2		0x16E
+#define SOC_ID_ARX182		0x16F
+#define SOC_ID_GRX188		0x170
+#define SOC_ID_GRX168		0x171
+
+#define SOC_ID_VRX288		0x1C0 /* v1.1 */
+#define SOC_ID_VRX282		0x1C1 /* v1.1 */
+#define SOC_ID_VRX268		0x1C2 /* v1.1 */
+#define SOC_ID_GRX268		0x1C8 /* v1.1 */
+#define SOC_ID_GRX288		0x1C9 /* v1.1 */
+#define SOC_ID_VRX288_2		0x00B /* v1.2 */
+#define SOC_ID_VRX268_2		0x00C /* v1.2 */
+#define SOC_ID_GRX288_2		0x00D /* v1.2 */
+#define SOC_ID_GRX282_2		0x00E /* v1.2 */
+#define SOC_ID_VRX220		0x000
+
+#define SOC_ID_ARX362		0x004
+#define SOC_ID_ARX368		0x005
+#define SOC_ID_ARX382		0x007
+#define SOC_ID_ARX388		0x008
+#define SOC_ID_URX388		0x009
+#define SOC_ID_GRX383		0x010
+#define SOC_ID_GRX369		0x011
+#define SOC_ID_GRX387		0x00F
+#define SOC_ID_GRX389		0x012
+
+ /* SoC Types */
+#define SOC_TYPE_DANUBE		0x01
+#define SOC_TYPE_TWINPASS	0x02
+#define SOC_TYPE_AR9		0x03
+#define SOC_TYPE_VR9		0x04 /* v1.1 */
+#define SOC_TYPE_VR9_2		0x05 /* v1.2 */
+#define SOC_TYPE_AMAZON_SE	0x06
+#define SOC_TYPE_AR10		0x07
+#define SOC_TYPE_GRX390		0x08
+#define SOC_TYPE_VRX220		0x09
+
+/* BOOT_SEL - find what boot media we have */
+#define BS_EXT_ROM		0x0
+#define BS_FLASH		0x1
+#define BS_MII0			0x2
+#define BS_PCI			0x3
+#define BS_UART1		0x4
+#define BS_SPI			0x5
+#define BS_NAND			0x6
+#define BS_RMII0		0x7
+
+/* helpers used to access the cgu */
+#define ltq_cgu_w32(x, y)	ltq_w32((x), ltq_cgu_membase + (y))
+#define ltq_cgu_r32(x)		ltq_r32(ltq_cgu_membase + (x))
+extern __iomem void *ltq_cgu_membase;
+
+/*
+ * during early_printk no ioremap is possible
+ * let's use KSEG1 instead
+ */
+#define LTQ_ASC1_BASE_ADDR	0x1E100C00
+#define LTQ_EARLY_ASC		KSEG1ADDR(LTQ_ASC1_BASE_ADDR)
+
+/* EBU - external bus unit */
+#define LTQ_EBU_BUSCON0		0x0060
+#define LTQ_EBU_PCC_CON		0x0090
+#define LTQ_EBU_PCC_IEN		0x00A4
+#define LTQ_EBU_PCC_ISTAT	0x00A0
+#define LTQ_EBU_BUSCON1		0x0064
+#define LTQ_EBU_ADDRSEL1	0x0024
+#define EBU_WRDIS		0x80000000
+
+/* WDT */
+#define LTQ_RST_CAUSE_WDTRST	0x20
+
+/* MPS - multi processor unit (voice) */
+#define LTQ_MPS_BASE_ADDR	(KSEG1 + 0x1F107000)
+#define LTQ_MPS_CHIPID		((u32 *)(LTQ_MPS_BASE_ADDR + 0x0344))
+
+/* allow booting xrx200 phys */
+int xrx200_gphy_boot(struct device *dev, unsigned int id, dma_addr_t dev_addr);
+
+/* request a non-gpio and set the PIO config */
+#define PMU_PPE			 BIT(13)
+extern void ltq_pmu_enable(unsigned int module);
+extern void ltq_pmu_disable(unsigned int module);
+
+#endif /* CONFIG_SOC_TYPE_XWAY */
+#endif /* _LTQ_XWAY_H__ */
diff --git a/arch/mips/include/asm/mach-lantiq/xway/xway_dma.h b/arch/mips/include/asm/mach-lantiq/xway/xway_dma.h
new file mode 100644
index 000000000..3dee15c61
--- /dev/null
+++ b/arch/mips/include/asm/mach-lantiq/xway/xway_dma.h
@@ -0,0 +1,50 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *
+ *   Copyright (C) 2011 John Crispin <john@phrozen.org>
+ */
+
+#ifndef LTQ_DMA_H__
+#define LTQ_DMA_H__
+
+#define LTQ_DESC_SIZE		0x08	/* each descriptor is 64bit */
+#define LTQ_DESC_NUM		0xC0	/* 192 descriptors / channel */
+
+#define LTQ_DMA_OWN		BIT(31) /* owner bit */
+#define LTQ_DMA_C		BIT(30) /* complete bit */
+#define LTQ_DMA_SOP		BIT(29) /* start of packet */
+#define LTQ_DMA_EOP		BIT(28) /* end of packet */
+#define LTQ_DMA_TX_OFFSET(x)	((x & 0x1f) << 23) /* data bytes offset */
+#define LTQ_DMA_RX_OFFSET(x)	((x & 0x7) << 23) /* data bytes offset */
+#define LTQ_DMA_SIZE_MASK	(0xffff) /* the size field is 16 bit */
+
+struct ltq_dma_desc {
+	u32 ctl;
+	u32 addr;
+};
+
+struct ltq_dma_channel {
+	int nr;				/* the channel number */
+	int irq;			/* the mapped irq */
+	int desc;			/* the current descriptor */
+	struct ltq_dma_desc *desc_base; /* the descriptor base */
+	int phys;			/* physical addr */
+	struct device *dev;
+};
+
+enum {
+	DMA_PORT_ETOP = 0,
+	DMA_PORT_DEU,
+};
+
+extern void ltq_dma_enable_irq(struct ltq_dma_channel *ch);
+extern void ltq_dma_disable_irq(struct ltq_dma_channel *ch);
+extern void ltq_dma_ack_irq(struct ltq_dma_channel *ch);
+extern void ltq_dma_open(struct ltq_dma_channel *ch);
+extern void ltq_dma_close(struct ltq_dma_channel *ch);
+extern void ltq_dma_alloc_tx(struct ltq_dma_channel *ch);
+extern void ltq_dma_alloc_rx(struct ltq_dma_channel *ch);
+extern void ltq_dma_free(struct ltq_dma_channel *ch);
+extern void ltq_dma_init_port(int p, int tx_burst, int rx_burst);
+
+#endif
diff --git a/arch/mips/include/asm/mach-loongson2ef/cpu-feature-overrides.h b/arch/mips/include/asm/mach-loongson2ef/cpu-feature-overrides.h
new file mode 100644
index 000000000..eb0d1cfb9
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson2ef/cpu-feature-overrides.h
@@ -0,0 +1,43 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2009 Wu Zhangjin <wuzhangjin@gmail.com>
+ * Copyright (C) 2009 Philippe Vachon <philippe@cowpig.ca>
+ * Copyright (C) 2009 Zhang Le <r0bertz@gentoo.org>
+ *
+ * reference: /proc/cpuinfo,
+ *	arch/mips/kernel/cpu-probe.c(cpu_probe_legacy),
+ *	arch/mips/kernel/proc.c(show_cpuinfo),
+ *	loongson2f user manual.
+ */
+
+#ifndef __ASM_MACH_LOONGSON2EF_CPU_FEATURE_OVERRIDES_H
+#define __ASM_MACH_LOONGSON2EF_CPU_FEATURE_OVERRIDES_H
+
+#define cpu_has_32fpr		1
+#define cpu_has_3k_cache	0
+#define cpu_has_4k_cache	1
+#define cpu_has_4kex		1
+#define cpu_has_64bits		1
+#define cpu_has_cache_cdex_p	0
+#define cpu_has_cache_cdex_s	0
+#define cpu_has_counter		1
+#define cpu_has_dc_aliases	(PAGE_SIZE < 0x4000)
+#define cpu_has_divec		0
+#define cpu_has_ejtag		0
+#define cpu_has_inclusive_pcaches	1
+#define cpu_has_llsc		1
+#define cpu_has_mcheck		0
+#define cpu_has_mdmx		0
+#define cpu_has_mips16		0
+#define cpu_has_mips16e2	0
+#define cpu_has_mips3d		0
+#define cpu_has_mipsmt		0
+#define cpu_has_smartmips	0
+#define cpu_has_tlb		1
+#define cpu_has_vce		0
+#define cpu_has_veic		0
+#define cpu_has_vint		0
+#define cpu_has_vtag_icache	0
+#define cpu_has_watch		1
+
+#endif /* __ASM_MACH_LOONGSON64_CPU_FEATURE_OVERRIDES_H */
diff --git a/arch/mips/include/asm/mach-loongson2ef/cs5536/cs5536.h b/arch/mips/include/asm/mach-loongson2ef/cs5536/cs5536.h
new file mode 100644
index 000000000..9795b3361
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson2ef/cs5536/cs5536.h
@@ -0,0 +1,306 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * The header file of cs5536 south bridge.
+ *
+ * Copyright (C) 2007 Lemote, Inc.
+ * Author : jlliu <liujl@lemote.com>
+ */
+
+#ifndef _CS5536_H
+#define _CS5536_H
+
+#include <linux/types.h>
+
+extern void _rdmsr(u32 msr, u32 *hi, u32 *lo);
+extern void _wrmsr(u32 msr, u32 hi, u32 lo);
+
+/*
+ * MSR module base
+ */
+#define CS5536_SB_MSR_BASE	(0x00000000)
+#define CS5536_GLIU_MSR_BASE	(0x10000000)
+#define CS5536_ILLEGAL_MSR_BASE (0x20000000)
+#define CS5536_USB_MSR_BASE	(0x40000000)
+#define CS5536_IDE_MSR_BASE	(0x60000000)
+#define CS5536_DIVIL_MSR_BASE	(0x80000000)
+#define CS5536_ACC_MSR_BASE	(0xa0000000)
+#define CS5536_UNUSED_MSR_BASE	(0xc0000000)
+#define CS5536_GLCP_MSR_BASE	(0xe0000000)
+
+#define SB_MSR_REG(offset)	(CS5536_SB_MSR_BASE	| (offset))
+#define GLIU_MSR_REG(offset)	(CS5536_GLIU_MSR_BASE	| (offset))
+#define ILLEGAL_MSR_REG(offset) (CS5536_ILLEGAL_MSR_BASE | (offset))
+#define USB_MSR_REG(offset)	(CS5536_USB_MSR_BASE	| (offset))
+#define IDE_MSR_REG(offset)	(CS5536_IDE_MSR_BASE	| (offset))
+#define DIVIL_MSR_REG(offset)	(CS5536_DIVIL_MSR_BASE	| (offset))
+#define ACC_MSR_REG(offset)	(CS5536_ACC_MSR_BASE	| (offset))
+#define UNUSED_MSR_REG(offset)	(CS5536_UNUSED_MSR_BASE | (offset))
+#define GLCP_MSR_REG(offset)	(CS5536_GLCP_MSR_BASE	| (offset))
+
+/*
+ * BAR SPACE OF VIRTUAL PCI :
+ * range for pci probe use, length is the actual size.
+ */
+/* IO space for all DIVIL modules */
+#define CS5536_IRQ_RANGE	0xffffffe0 /* USERD FOR PCI PROBE */
+#define CS5536_IRQ_LENGTH	0x20	/* THE REGS ACTUAL LENGTH */
+#define CS5536_SMB_RANGE	0xfffffff8
+#define CS5536_SMB_LENGTH	0x08
+#define CS5536_GPIO_RANGE	0xffffff00
+#define CS5536_GPIO_LENGTH	0x100
+#define CS5536_MFGPT_RANGE	0xffffffc0
+#define CS5536_MFGPT_LENGTH	0x40
+#define CS5536_ACPI_RANGE	0xffffffe0
+#define CS5536_ACPI_LENGTH	0x20
+#define CS5536_PMS_RANGE	0xffffff80
+#define CS5536_PMS_LENGTH	0x80
+/* IO space for IDE */
+#define CS5536_IDE_RANGE	0xfffffff0
+#define CS5536_IDE_LENGTH	0x10
+/* IO space for ACC */
+#define CS5536_ACC_RANGE	0xffffff80
+#define CS5536_ACC_LENGTH	0x80
+/* MEM space for ALL USB modules */
+#define CS5536_OHCI_RANGE	0xfffff000
+#define CS5536_OHCI_LENGTH	0x1000
+#define CS5536_EHCI_RANGE	0xfffff000
+#define CS5536_EHCI_LENGTH	0x1000
+
+/*
+ * PCI MSR ACCESS
+ */
+#define PCI_MSR_CTRL		0xF0
+#define PCI_MSR_ADDR		0xF4
+#define PCI_MSR_DATA_LO		0xF8
+#define PCI_MSR_DATA_HI		0xFC
+
+/**************** MSR *****************************/
+
+/*
+ * GLIU STANDARD MSR
+ */
+#define GLIU_CAP		0x00
+#define GLIU_CONFIG		0x01
+#define GLIU_SMI		0x02
+#define GLIU_ERROR		0x03
+#define GLIU_PM			0x04
+#define GLIU_DIAG		0x05
+
+/*
+ * GLIU SPEC. MSR
+ */
+#define GLIU_P2D_BM0		0x20
+#define GLIU_P2D_BM1		0x21
+#define GLIU_P2D_BM2		0x22
+#define GLIU_P2D_BMK0		0x23
+#define GLIU_P2D_BMK1		0x24
+#define GLIU_P2D_BM3		0x25
+#define GLIU_P2D_BM4		0x26
+#define GLIU_COH		0x80
+#define GLIU_PAE		0x81
+#define GLIU_ARB		0x82
+#define GLIU_ASMI		0x83
+#define GLIU_AERR		0x84
+#define GLIU_DEBUG		0x85
+#define GLIU_PHY_CAP		0x86
+#define GLIU_NOUT_RESP		0x87
+#define GLIU_NOUT_WDATA		0x88
+#define GLIU_WHOAMI		0x8B
+#define GLIU_SLV_DIS		0x8C
+#define GLIU_IOD_BM0		0xE0
+#define GLIU_IOD_BM1		0xE1
+#define GLIU_IOD_BM2		0xE2
+#define GLIU_IOD_BM3		0xE3
+#define GLIU_IOD_BM4		0xE4
+#define GLIU_IOD_BM5		0xE5
+#define GLIU_IOD_BM6		0xE6
+#define GLIU_IOD_BM7		0xE7
+#define GLIU_IOD_BM8		0xE8
+#define GLIU_IOD_BM9		0xE9
+#define GLIU_IOD_SC0		0xEA
+#define GLIU_IOD_SC1		0xEB
+#define GLIU_IOD_SC2		0xEC
+#define GLIU_IOD_SC3		0xED
+#define GLIU_IOD_SC4		0xEE
+#define GLIU_IOD_SC5		0xEF
+#define GLIU_IOD_SC6		0xF0
+#define GLIU_IOD_SC7		0xF1
+
+/*
+ * SB STANDARD
+ */
+#define SB_CAP		0x00
+#define SB_CONFIG	0x01
+#define SB_SMI		0x02
+#define SB_ERROR	0x03
+#define SB_MAR_ERR_EN		0x00000001
+#define SB_TAR_ERR_EN		0x00000002
+#define SB_RSVD_BIT1		0x00000004
+#define SB_EXCEP_ERR_EN		0x00000008
+#define SB_SYSE_ERR_EN		0x00000010
+#define SB_PARE_ERR_EN		0x00000020
+#define SB_TAS_ERR_EN		0x00000040
+#define SB_MAR_ERR_FLAG		0x00010000
+#define SB_TAR_ERR_FLAG		0x00020000
+#define SB_RSVD_BIT2		0x00040000
+#define SB_EXCEP_ERR_FLAG	0x00080000
+#define SB_SYSE_ERR_FLAG	0x00100000
+#define SB_PARE_ERR_FLAG	0x00200000
+#define SB_TAS_ERR_FLAG		0x00400000
+#define SB_PM		0x04
+#define SB_DIAG		0x05
+
+/*
+ * SB SPEC.
+ */
+#define SB_CTRL		0x10
+#define SB_R0		0x20
+#define SB_R1		0x21
+#define SB_R2		0x22
+#define SB_R3		0x23
+#define SB_R4		0x24
+#define SB_R5		0x25
+#define SB_R6		0x26
+#define SB_R7		0x27
+#define SB_R8		0x28
+#define SB_R9		0x29
+#define SB_R10		0x2A
+#define SB_R11		0x2B
+#define SB_R12		0x2C
+#define SB_R13		0x2D
+#define SB_R14		0x2E
+#define SB_R15		0x2F
+
+/*
+ * GLCP STANDARD
+ */
+#define GLCP_CAP		0x00
+#define GLCP_CONFIG		0x01
+#define GLCP_SMI		0x02
+#define GLCP_ERROR		0x03
+#define GLCP_PM			0x04
+#define GLCP_DIAG		0x05
+
+/*
+ * GLCP SPEC.
+ */
+#define GLCP_CLK_DIS_DELAY	0x08
+#define GLCP_PM_CLK_DISABLE	0x09
+#define GLCP_GLB_PM		0x0B
+#define GLCP_DBG_OUT		0x0C
+#define GLCP_RSVD1		0x0D
+#define GLCP_SOFT_COM		0x0E
+#define SOFT_BAR_SMB_FLAG	0x00000001
+#define SOFT_BAR_GPIO_FLAG	0x00000002
+#define SOFT_BAR_MFGPT_FLAG	0x00000004
+#define SOFT_BAR_IRQ_FLAG	0x00000008
+#define SOFT_BAR_PMS_FLAG	0x00000010
+#define SOFT_BAR_ACPI_FLAG	0x00000020
+#define SOFT_BAR_IDE_FLAG	0x00000400
+#define SOFT_BAR_ACC_FLAG	0x00000800
+#define SOFT_BAR_OHCI_FLAG	0x00001000
+#define SOFT_BAR_EHCI_FLAG	0x00002000
+#define GLCP_RSVD2		0x0F
+#define GLCP_CLK_OFF		0x10
+#define GLCP_CLK_ACTIVE		0x11
+#define GLCP_CLK_DISABLE	0x12
+#define GLCP_CLK4ACK		0x13
+#define GLCP_SYS_RST		0x14
+#define GLCP_RSVD3		0x15
+#define GLCP_DBG_CLK_CTRL	0x16
+#define GLCP_CHIP_REV_ID	0x17
+
+/* PIC */
+#define PIC_YSEL_LOW		0x20
+#define PIC_YSEL_LOW_USB_SHIFT		8
+#define PIC_YSEL_LOW_ACC_SHIFT		16
+#define PIC_YSEL_LOW_FLASH_SHIFT	24
+#define PIC_YSEL_HIGH		0x21
+#define PIC_ZSEL_LOW		0x22
+#define PIC_ZSEL_HIGH		0x23
+#define PIC_IRQM_PRIM		0x24
+#define PIC_IRQM_LPC		0x25
+#define PIC_XIRR_STS_LOW	0x26
+#define PIC_XIRR_STS_HIGH	0x27
+#define PCI_SHDW		0x34
+
+/*
+ * DIVIL STANDARD
+ */
+#define DIVIL_CAP		0x00
+#define DIVIL_CONFIG		0x01
+#define DIVIL_SMI		0x02
+#define DIVIL_ERROR		0x03
+#define DIVIL_PM		0x04
+#define DIVIL_DIAG		0x05
+
+/*
+ * DIVIL SPEC.
+ */
+#define DIVIL_LBAR_IRQ		0x08
+#define DIVIL_LBAR_KEL		0x09
+#define DIVIL_LBAR_SMB		0x0B
+#define DIVIL_LBAR_GPIO		0x0C
+#define DIVIL_LBAR_MFGPT	0x0D
+#define DIVIL_LBAR_ACPI		0x0E
+#define DIVIL_LBAR_PMS		0x0F
+#define DIVIL_LEG_IO		0x14
+#define DIVIL_BALL_OPTS		0x15
+#define DIVIL_SOFT_IRQ		0x16
+#define DIVIL_SOFT_RESET	0x17
+
+/* MFGPT */
+#define MFGPT_IRQ	0x28
+
+/*
+ * IDE STANDARD
+ */
+#define IDE_CAP		0x00
+#define IDE_CONFIG	0x01
+#define IDE_SMI		0x02
+#define IDE_ERROR	0x03
+#define IDE_PM		0x04
+#define IDE_DIAG	0x05
+
+/*
+ * IDE SPEC.
+ */
+#define IDE_IO_BAR	0x08
+#define IDE_CFG		0x10
+#define IDE_DTC		0x12
+#define IDE_CAST	0x13
+#define IDE_ETC		0x14
+#define IDE_INTERNAL_PM 0x15
+
+/*
+ * ACC STANDARD
+ */
+#define ACC_CAP		0x00
+#define ACC_CONFIG	0x01
+#define ACC_SMI		0x02
+#define ACC_ERROR	0x03
+#define ACC_PM		0x04
+#define ACC_DIAG	0x05
+
+/*
+ * USB STANDARD
+ */
+#define USB_CAP		0x00
+#define USB_CONFIG	0x01
+#define USB_SMI		0x02
+#define USB_ERROR	0x03
+#define USB_PM		0x04
+#define USB_DIAG	0x05
+
+/*
+ * USB SPEC.
+ */
+#define USB_OHCI	0x08
+#define USB_EHCI	0x09
+
+/****************** NATIVE ***************************/
+/* GPIO : I/O SPACE; REG : 32BITS */
+#define GPIOL_OUT_VAL		0x00
+#define GPIOL_OUT_EN		0x04
+
+#endif				/* _CS5536_H */
diff --git a/arch/mips/include/asm/mach-loongson2ef/cs5536/cs5536_mfgpt.h b/arch/mips/include/asm/mach-loongson2ef/cs5536/cs5536_mfgpt.h
new file mode 100644
index 000000000..52e8bb0fc
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson2ef/cs5536/cs5536_mfgpt.h
@@ -0,0 +1,36 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * cs5536 mfgpt header file
+ */
+
+#ifndef _CS5536_MFGPT_H
+#define _CS5536_MFGPT_H
+
+#include <cs5536/cs5536.h>
+#include <cs5536/cs5536_pci.h>
+
+#ifdef CONFIG_CS5536_MFGPT
+extern void setup_mfgpt0_timer(void);
+extern void disable_mfgpt0_counter(void);
+extern void enable_mfgpt0_counter(void);
+#else
+static inline void __maybe_unused setup_mfgpt0_timer(void)
+{
+}
+static inline void __maybe_unused disable_mfgpt0_counter(void)
+{
+}
+static inline void __maybe_unused enable_mfgpt0_counter(void)
+{
+}
+#endif
+
+#define MFGPT_TICK_RATE 14318000
+#define COMPARE	 ((MFGPT_TICK_RATE + HZ/2) / HZ)
+
+#define MFGPT_BASE	mfgpt_base
+#define MFGPT0_CMP2	(MFGPT_BASE + 2)
+#define MFGPT0_CNT	(MFGPT_BASE + 4)
+#define MFGPT0_SETUP	(MFGPT_BASE + 6)
+
+#endif /*!_CS5536_MFGPT_H */
diff --git a/arch/mips/include/asm/mach-loongson2ef/cs5536/cs5536_pci.h b/arch/mips/include/asm/mach-loongson2ef/cs5536/cs5536_pci.h
new file mode 100644
index 000000000..a0d4b7528
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson2ef/cs5536/cs5536_pci.h
@@ -0,0 +1,153 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * the definition file of cs5536 Virtual Support Module(VSM).
+ * pci configuration space can be accessed through the VSM, so
+ * there is no need of the MSR read/write now, except the spec.
+ * MSR registers which are not implemented yet.
+ *
+ * Copyright (C) 2007 Lemote Inc.
+ * Author : jlliu, liujl@lemote.com
+ */
+
+#ifndef _CS5536_PCI_H
+#define _CS5536_PCI_H
+
+#include <linux/types.h>
+#include <linux/pci_regs.h>
+
+extern void cs5536_pci_conf_write4(int function, int reg, u32 value);
+extern u32 cs5536_pci_conf_read4(int function, int reg);
+
+#define CS5536_ACC_INTR		9
+#define CS5536_IDE_INTR		14
+#define CS5536_USB_INTR		11
+#define CS5536_MFGPT_INTR	5
+#define CS5536_UART1_INTR	4
+#define CS5536_UART2_INTR	3
+
+/************** PCI BUS DEVICE FUNCTION ***************/
+
+/*
+ * PCI bus device function
+ */
+#define PCI_BUS_CS5536		0
+#define PCI_IDSEL_CS5536	14
+
+/********** STANDARD PCI-2.2 EXPANSION ****************/
+
+/*
+ * PCI configuration space
+ * we have to virtualize the PCI configure space head, so we should
+ * define the necessary IDs and some others.
+ */
+
+/* CONFIG of PCI VENDOR ID*/
+#define CFG_PCI_VENDOR_ID(mod_dev_id, sys_vendor_id) \
+	(((mod_dev_id) << 16) | (sys_vendor_id))
+
+/* VENDOR ID */
+#define CS5536_VENDOR_ID	0x1022
+
+/* DEVICE ID */
+#define CS5536_ISA_DEVICE_ID		0x2090
+#define CS5536_IDE_DEVICE_ID		0x209a
+#define CS5536_ACC_DEVICE_ID		0x2093
+#define CS5536_OHCI_DEVICE_ID		0x2094
+#define CS5536_EHCI_DEVICE_ID		0x2095
+
+/* CLASS CODE : CLASS SUB-CLASS INTERFACE */
+#define CS5536_ISA_CLASS_CODE		0x060100
+#define CS5536_IDE_CLASS_CODE		0x010180
+#define CS5536_ACC_CLASS_CODE		0x040100
+#define CS5536_OHCI_CLASS_CODE		0x0C0310
+#define CS5536_EHCI_CLASS_CODE		0x0C0320
+
+/* BHLC : BIST HEADER-TYPE LATENCY-TIMER CACHE-LINE-SIZE */
+
+#define CFG_PCI_CACHE_LINE_SIZE(header_type, latency_timer)	\
+	((PCI_NONE_BIST << 24) | ((header_type) << 16) \
+		| ((latency_timer) << 8) | PCI_NORMAL_CACHE_LINE_SIZE);
+
+#define PCI_NONE_BIST			0x00	/* RO not implemented yet. */
+#define PCI_BRIDGE_HEADER_TYPE		0x80	/* RO */
+#define PCI_NORMAL_HEADER_TYPE		0x00
+#define PCI_NORMAL_LATENCY_TIMER	0x00
+#define PCI_NORMAL_CACHE_LINE_SIZE	0x08	/* RW */
+
+/* BAR */
+#define PCI_BAR0_REG			0x10
+#define PCI_BAR1_REG			0x14
+#define PCI_BAR2_REG			0x18
+#define PCI_BAR3_REG			0x1c
+#define PCI_BAR4_REG			0x20
+#define PCI_BAR5_REG			0x24
+#define PCI_BAR_RANGE_MASK		0xFFFFFFFF
+
+/* CARDBUS CIS POINTER */
+#define PCI_CARDBUS_CIS_POINTER		0x00000000
+
+/* SUBSYSTEM VENDOR ID	*/
+#define CS5536_SUB_VENDOR_ID		CS5536_VENDOR_ID
+
+/* SUBSYSTEM ID */
+#define CS5536_ISA_SUB_ID		CS5536_ISA_DEVICE_ID
+#define CS5536_IDE_SUB_ID		CS5536_IDE_DEVICE_ID
+#define CS5536_ACC_SUB_ID		CS5536_ACC_DEVICE_ID
+#define CS5536_OHCI_SUB_ID		CS5536_OHCI_DEVICE_ID
+#define CS5536_EHCI_SUB_ID		CS5536_EHCI_DEVICE_ID
+
+/* EXPANSION ROM BAR */
+#define PCI_EXPANSION_ROM_BAR		0x00000000
+
+/* CAPABILITIES POINTER */
+#define PCI_CAPLIST_POINTER		0x00000000
+#define PCI_CAPLIST_USB_POINTER		0x40
+/* INTERRUPT */
+
+#define CFG_PCI_INTERRUPT_LINE(pin, mod_intr) \
+	((PCI_MAX_LATENCY << 24) | (PCI_MIN_GRANT << 16) | \
+		((pin) << 8) | (mod_intr))
+
+#define PCI_MAX_LATENCY			0x40
+#define PCI_MIN_GRANT			0x00
+#define PCI_DEFAULT_PIN			0x01
+
+/*********** EXPANSION PCI REG ************************/
+
+/*
+ * ISA EXPANSION
+ */
+#define PCI_UART1_INT_REG	0x50
+#define PCI_UART2_INT_REG	0x54
+#define PCI_ISA_FIXUP_REG	0x58
+
+/*
+ * IDE EXPANSION
+ */
+#define PCI_IDE_CFG_REG		0x40
+#define CS5536_IDE_FLASH_SIGNATURE	0xDEADBEEF
+#define PCI_IDE_DTC_REG		0x48
+#define PCI_IDE_CAST_REG	0x4C
+#define PCI_IDE_ETC_REG		0x50
+#define PCI_IDE_PM_REG		0x54
+#define PCI_IDE_INT_REG		0x60
+
+/*
+ * ACC EXPANSION
+ */
+#define PCI_ACC_INT_REG		0x50
+
+/*
+ * OHCI EXPANSION : INTTERUPT IS IMPLEMENTED BY THE OHCI
+ */
+#define PCI_OHCI_PM_REG		0x40
+#define PCI_OHCI_INT_REG	0x50
+
+/*
+ * EHCI EXPANSION
+ */
+#define PCI_EHCI_LEGSMIEN_REG	0x50
+#define PCI_EHCI_LEGSMISTS_REG	0x54
+#define PCI_EHCI_FLADJ_REG	0x60
+
+#endif				/* _CS5536_PCI_H_ */
diff --git a/arch/mips/include/asm/mach-loongson2ef/cs5536/cs5536_vsm.h b/arch/mips/include/asm/mach-loongson2ef/cs5536/cs5536_vsm.h
new file mode 100644
index 000000000..70d0153cc
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson2ef/cs5536/cs5536_vsm.h
@@ -0,0 +1,32 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * the read/write interfaces for Virtual Support Module(VSM)
+ *
+ * Copyright (C) 2009 Lemote, Inc.
+ * Author: Wu Zhangjin <wuzhangjin@gmail.com>
+ */
+
+#ifndef _CS5536_VSM_H
+#define _CS5536_VSM_H
+
+#include <linux/types.h>
+
+typedef void (*cs5536_pci_vsm_write)(int reg, u32 value);
+typedef u32 (*cs5536_pci_vsm_read)(int reg);
+
+#define DECLARE_CS5536_MODULE(name) \
+extern void pci_##name##_write_reg(int reg, u32 value); \
+extern u32 pci_##name##_read_reg(int reg);
+
+/* ide module */
+DECLARE_CS5536_MODULE(ide)
+/* acc module */
+DECLARE_CS5536_MODULE(acc)
+/* ohci module */
+DECLARE_CS5536_MODULE(ohci)
+/* isa module */
+DECLARE_CS5536_MODULE(isa)
+/* ehci module */
+DECLARE_CS5536_MODULE(ehci)
+
+#endif				/* _CS5536_VSM_H */
diff --git a/arch/mips/include/asm/mach-loongson2ef/loongson.h b/arch/mips/include/asm/mach-loongson2ef/loongson.h
new file mode 100644
index 000000000..ca039b8dc
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson2ef/loongson.h
@@ -0,0 +1,318 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2009 Lemote, Inc.
+ * Author: Wu Zhangjin <wuzhangjin@gmail.com>
+ */
+
+#ifndef __ASM_MACH_LOONGSON2EF_LOONGSON_H
+#define __ASM_MACH_LOONGSON2EF_LOONGSON_H
+
+#include <linux/io.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+
+/* loongson internal northbridge initialization */
+extern void bonito_irq_init(void);
+
+/* machine-specific reboot/halt operation */
+extern void mach_prepare_reboot(void);
+extern void mach_prepare_shutdown(void);
+
+/* environment arguments from bootloader */
+extern u32 cpu_clock_freq;
+extern u32 memsize, highmemsize;
+
+/* loongson-specific command line, env and memory initialization */
+extern void __init prom_init_memory(void);
+extern void __init prom_init_machtype(void);
+extern void __init prom_init_env(void);
+#ifdef CONFIG_LOONGSON_UART_BASE
+extern unsigned long _loongson_uart_base, loongson_uart_base;
+extern void prom_init_loongson_uart_base(void);
+#endif
+
+static inline void prom_init_uart_base(void)
+{
+#ifdef CONFIG_LOONGSON_UART_BASE
+	prom_init_loongson_uart_base();
+#endif
+}
+
+/* irq operation functions */
+extern void bonito_irqdispatch(void);
+extern void __init bonito_irq_init(void);
+extern void __init mach_init_irq(void);
+extern void mach_irq_dispatch(unsigned int pending);
+extern int mach_i8259_irq(void);
+
+/* We need this in some places... */
+#define delay() ({		\
+	int x;				\
+	for (x = 0; x < 100000; x++)	\
+		__asm__ __volatile__(""); \
+})
+
+#define LOONGSON_REG(x) \
+	(*(volatile u32 *)((char *)CKSEG1ADDR(LOONGSON_REG_BASE) + (x)))
+
+#define LOONGSON_IRQ_BASE	32
+
+#define LOONGSON_FLASH_BASE	0x1c000000
+#define LOONGSON_FLASH_SIZE	0x02000000	/* 32M */
+#define LOONGSON_FLASH_TOP	(LOONGSON_FLASH_BASE+LOONGSON_FLASH_SIZE-1)
+
+#define LOONGSON_LIO0_BASE	0x1e000000
+#define LOONGSON_LIO0_SIZE	0x01C00000	/* 28M */
+#define LOONGSON_LIO0_TOP	(LOONGSON_LIO0_BASE+LOONGSON_LIO0_SIZE-1)
+
+#define LOONGSON_BOOT_BASE	0x1fc00000
+#define LOONGSON_BOOT_SIZE	0x00100000	/* 1M */
+#define LOONGSON_BOOT_TOP	(LOONGSON_BOOT_BASE+LOONGSON_BOOT_SIZE-1)
+#define LOONGSON_REG_BASE	0x1fe00000
+#define LOONGSON_REG_SIZE	0x00100000	/* 256Bytes + 256Bytes + ??? */
+#define LOONGSON_REG_TOP	(LOONGSON_REG_BASE+LOONGSON_REG_SIZE-1)
+
+#define LOONGSON_LIO1_BASE	0x1ff00000
+#define LOONGSON_LIO1_SIZE	0x00100000	/* 1M */
+#define LOONGSON_LIO1_TOP	(LOONGSON_LIO1_BASE+LOONGSON_LIO1_SIZE-1)
+
+#define LOONGSON_PCILO0_BASE	0x10000000
+#define LOONGSON_PCILO1_BASE	0x14000000
+#define LOONGSON_PCILO2_BASE	0x18000000
+#define LOONGSON_PCILO_BASE	LOONGSON_PCILO0_BASE
+#define LOONGSON_PCILO_SIZE	0x0c000000	/* 64M * 3 */
+#define LOONGSON_PCILO_TOP	(LOONGSON_PCILO0_BASE+LOONGSON_PCILO_SIZE-1)
+
+#define LOONGSON_PCICFG_BASE	0x1fe80000
+#define LOONGSON_PCICFG_SIZE	0x00000800	/* 2K */
+#define LOONGSON_PCICFG_TOP	(LOONGSON_PCICFG_BASE+LOONGSON_PCICFG_SIZE-1)
+#define LOONGSON_PCIIO_BASE	0x1fd00000
+
+#define LOONGSON_PCIIO_SIZE	0x00100000	/* 1M */
+#define LOONGSON_PCIIO_TOP	(LOONGSON_PCIIO_BASE+LOONGSON_PCIIO_SIZE-1)
+
+/* Loongson Register Bases */
+
+#define LOONGSON_PCICONFIGBASE	0x00
+#define LOONGSON_REGBASE	0x100
+
+/* PCI Configuration Registers */
+
+#define LOONGSON_PCI_REG(x)	LOONGSON_REG(LOONGSON_PCICONFIGBASE + (x))
+#define LOONGSON_PCIDID		LOONGSON_PCI_REG(0x00)
+#define LOONGSON_PCICMD		LOONGSON_PCI_REG(0x04)
+#define LOONGSON_PCICLASS	LOONGSON_PCI_REG(0x08)
+#define LOONGSON_PCILTIMER	LOONGSON_PCI_REG(0x0c)
+#define LOONGSON_PCIBASE0	LOONGSON_PCI_REG(0x10)
+#define LOONGSON_PCIBASE1	LOONGSON_PCI_REG(0x14)
+#define LOONGSON_PCIBASE2	LOONGSON_PCI_REG(0x18)
+#define LOONGSON_PCIBASE3	LOONGSON_PCI_REG(0x1c)
+#define LOONGSON_PCIBASE4	LOONGSON_PCI_REG(0x20)
+#define LOONGSON_PCIEXPRBASE	LOONGSON_PCI_REG(0x30)
+#define LOONGSON_PCIINT		LOONGSON_PCI_REG(0x3c)
+
+#define LOONGSON_PCI_ISR4C	LOONGSON_PCI_REG(0x4c)
+
+#define LOONGSON_PCICMD_PERR_CLR	0x80000000
+#define LOONGSON_PCICMD_SERR_CLR	0x40000000
+#define LOONGSON_PCICMD_MABORT_CLR	0x20000000
+#define LOONGSON_PCICMD_MTABORT_CLR	0x10000000
+#define LOONGSON_PCICMD_TABORT_CLR	0x08000000
+#define LOONGSON_PCICMD_MPERR_CLR	0x01000000
+#define LOONGSON_PCICMD_PERRRESPEN	0x00000040
+#define LOONGSON_PCICMD_ASTEPEN		0x00000080
+#define LOONGSON_PCICMD_SERREN		0x00000100
+#define LOONGSON_PCILTIMER_BUSLATENCY	0x0000ff00
+#define LOONGSON_PCILTIMER_BUSLATENCY_SHIFT	8
+
+/* Loongson h/w Configuration */
+
+#define LOONGSON_GENCFG_OFFSET		0x4
+#define LOONGSON_GENCFG LOONGSON_REG(LOONGSON_REGBASE + LOONGSON_GENCFG_OFFSET)
+
+#define LOONGSON_GENCFG_DEBUGMODE	0x00000001
+#define LOONGSON_GENCFG_SNOOPEN		0x00000002
+#define LOONGSON_GENCFG_CPUSELFRESET	0x00000004
+
+#define LOONGSON_GENCFG_FORCE_IRQA	0x00000008
+#define LOONGSON_GENCFG_IRQA_ISOUT	0x00000010
+#define LOONGSON_GENCFG_IRQA_FROM_INT1	0x00000020
+#define LOONGSON_GENCFG_BYTESWAP	0x00000040
+
+#define LOONGSON_GENCFG_UNCACHED	0x00000080
+#define LOONGSON_GENCFG_PREFETCHEN	0x00000100
+#define LOONGSON_GENCFG_WBEHINDEN	0x00000200
+#define LOONGSON_GENCFG_CACHEALG	0x00000c00
+#define LOONGSON_GENCFG_CACHEALG_SHIFT	10
+#define LOONGSON_GENCFG_PCIQUEUE	0x00001000
+#define LOONGSON_GENCFG_CACHESTOP	0x00002000
+#define LOONGSON_GENCFG_MSTRBYTESWAP	0x00004000
+#define LOONGSON_GENCFG_BUSERREN	0x00008000
+#define LOONGSON_GENCFG_NORETRYTIMEOUT	0x00010000
+#define LOONGSON_GENCFG_SHORTCOPYTIMEOUT	0x00020000
+
+/* PCI address map control */
+
+#define LOONGSON_PCIMAP			LOONGSON_REG(LOONGSON_REGBASE + 0x10)
+#define LOONGSON_PCIMEMBASECFG		LOONGSON_REG(LOONGSON_REGBASE + 0x14)
+#define LOONGSON_PCIMAP_CFG		LOONGSON_REG(LOONGSON_REGBASE + 0x18)
+
+/* GPIO Regs - r/w */
+
+#define LOONGSON_GPIODATA		LOONGSON_REG(LOONGSON_REGBASE + 0x1c)
+#define LOONGSON_GPIOIE			LOONGSON_REG(LOONGSON_REGBASE + 0x20)
+
+/* ICU Configuration Regs - r/w */
+
+#define LOONGSON_INTEDGE		LOONGSON_REG(LOONGSON_REGBASE + 0x24)
+#define LOONGSON_INTSTEER		LOONGSON_REG(LOONGSON_REGBASE + 0x28)
+#define LOONGSON_INTPOL			LOONGSON_REG(LOONGSON_REGBASE + 0x2c)
+
+/* ICU Enable Regs - IntEn & IntISR are r/o. */
+
+#define LOONGSON_INTENSET		LOONGSON_REG(LOONGSON_REGBASE + 0x30)
+#define LOONGSON_INTENCLR		LOONGSON_REG(LOONGSON_REGBASE + 0x34)
+#define LOONGSON_INTEN			LOONGSON_REG(LOONGSON_REGBASE + 0x38)
+#define LOONGSON_INTISR			LOONGSON_REG(LOONGSON_REGBASE + 0x3c)
+
+/* ICU */
+#define LOONGSON_ICU_MBOXES		0x0000000f
+#define LOONGSON_ICU_MBOXES_SHIFT	0
+#define LOONGSON_ICU_DMARDY		0x00000010
+#define LOONGSON_ICU_DMAEMPTY		0x00000020
+#define LOONGSON_ICU_COPYRDY		0x00000040
+#define LOONGSON_ICU_COPYEMPTY		0x00000080
+#define LOONGSON_ICU_COPYERR		0x00000100
+#define LOONGSON_ICU_PCIIRQ		0x00000200
+#define LOONGSON_ICU_MASTERERR		0x00000400
+#define LOONGSON_ICU_SYSTEMERR		0x00000800
+#define LOONGSON_ICU_DRAMPERR		0x00001000
+#define LOONGSON_ICU_RETRYERR		0x00002000
+#define LOONGSON_ICU_GPIOS		0x01ff0000
+#define LOONGSON_ICU_GPIOS_SHIFT		16
+#define LOONGSON_ICU_GPINS		0x7e000000
+#define LOONGSON_ICU_GPINS_SHIFT		25
+#define LOONGSON_ICU_MBOX(N)		(1<<(LOONGSON_ICU_MBOXES_SHIFT+(N)))
+#define LOONGSON_ICU_GPIO(N)		(1<<(LOONGSON_ICU_GPIOS_SHIFT+(N)))
+#define LOONGSON_ICU_GPIN(N)		(1<<(LOONGSON_ICU_GPINS_SHIFT+(N)))
+
+/* PCI prefetch window base & mask */
+
+#define LOONGSON_MEM_WIN_BASE_L		LOONGSON_REG(LOONGSON_REGBASE + 0x40)
+#define LOONGSON_MEM_WIN_BASE_H		LOONGSON_REG(LOONGSON_REGBASE + 0x44)
+#define LOONGSON_MEM_WIN_MASK_L		LOONGSON_REG(LOONGSON_REGBASE + 0x48)
+#define LOONGSON_MEM_WIN_MASK_H		LOONGSON_REG(LOONGSON_REGBASE + 0x4c)
+
+/* PCI_Hit*_Sel_* */
+
+#define LOONGSON_PCI_HIT0_SEL_L		LOONGSON_REG(LOONGSON_REGBASE + 0x50)
+#define LOONGSON_PCI_HIT0_SEL_H		LOONGSON_REG(LOONGSON_REGBASE + 0x54)
+#define LOONGSON_PCI_HIT1_SEL_L		LOONGSON_REG(LOONGSON_REGBASE + 0x58)
+#define LOONGSON_PCI_HIT1_SEL_H		LOONGSON_REG(LOONGSON_REGBASE + 0x5c)
+#define LOONGSON_PCI_HIT2_SEL_L		LOONGSON_REG(LOONGSON_REGBASE + 0x60)
+#define LOONGSON_PCI_HIT2_SEL_H		LOONGSON_REG(LOONGSON_REGBASE + 0x64)
+
+/* PXArb Config & Status */
+
+#define LOONGSON_PXARB_CFG		LOONGSON_REG(LOONGSON_REGBASE + 0x68)
+#define LOONGSON_PXARB_STATUS		LOONGSON_REG(LOONGSON_REGBASE + 0x6c)
+
+/* Chip Config registor of each physical cpu package, PRid >= Loongson-2F */
+#define LOONGSON_CHIPCFG	(void __iomem *)TO_UNCAC(0x1fc00180)
+
+/* pcimap */
+
+#define LOONGSON_PCIMAP_PCIMAP_LO0	0x0000003f
+#define LOONGSON_PCIMAP_PCIMAP_LO0_SHIFT	0
+#define LOONGSON_PCIMAP_PCIMAP_LO1	0x00000fc0
+#define LOONGSON_PCIMAP_PCIMAP_LO1_SHIFT	6
+#define LOONGSON_PCIMAP_PCIMAP_LO2	0x0003f000
+#define LOONGSON_PCIMAP_PCIMAP_LO2_SHIFT	12
+#define LOONGSON_PCIMAP_PCIMAP_2	0x00040000
+#define LOONGSON_PCIMAP_WIN(WIN, ADDR)	\
+	((((ADDR)>>26) & LOONGSON_PCIMAP_PCIMAP_LO0) << ((WIN)*6))
+
+#ifdef CONFIG_CPU_SUPPORTS_CPUFREQ
+#include <linux/cpufreq.h>
+extern struct cpufreq_frequency_table loongson2_clockmod_table[];
+extern int loongson2_cpu_set_rate(unsigned long rate_khz);
+#endif
+
+/*
+ * address windows configuration module
+ *
+ * loongson2e do not have this module
+ */
+#ifdef CONFIG_CPU_SUPPORTS_ADDRWINCFG
+
+/* address window config module base address */
+#define LOONGSON_ADDRWINCFG_BASE		0x3ff00000ul
+#define LOONGSON_ADDRWINCFG_SIZE		0x180
+
+extern unsigned long _loongson_addrwincfg_base;
+#define LOONGSON_ADDRWINCFG(offset) \
+	(*(volatile u64 *)(_loongson_addrwincfg_base + (offset)))
+
+#define CPU_WIN0_BASE	LOONGSON_ADDRWINCFG(0x00)
+#define CPU_WIN1_BASE	LOONGSON_ADDRWINCFG(0x08)
+#define CPU_WIN2_BASE	LOONGSON_ADDRWINCFG(0x10)
+#define CPU_WIN3_BASE	LOONGSON_ADDRWINCFG(0x18)
+
+#define CPU_WIN0_MASK	LOONGSON_ADDRWINCFG(0x20)
+#define CPU_WIN1_MASK	LOONGSON_ADDRWINCFG(0x28)
+#define CPU_WIN2_MASK	LOONGSON_ADDRWINCFG(0x30)
+#define CPU_WIN3_MASK	LOONGSON_ADDRWINCFG(0x38)
+
+#define CPU_WIN0_MMAP	LOONGSON_ADDRWINCFG(0x40)
+#define CPU_WIN1_MMAP	LOONGSON_ADDRWINCFG(0x48)
+#define CPU_WIN2_MMAP	LOONGSON_ADDRWINCFG(0x50)
+#define CPU_WIN3_MMAP	LOONGSON_ADDRWINCFG(0x58)
+
+#define PCIDMA_WIN0_BASE	LOONGSON_ADDRWINCFG(0x60)
+#define PCIDMA_WIN1_BASE	LOONGSON_ADDRWINCFG(0x68)
+#define PCIDMA_WIN2_BASE	LOONGSON_ADDRWINCFG(0x70)
+#define PCIDMA_WIN3_BASE	LOONGSON_ADDRWINCFG(0x78)
+
+#define PCIDMA_WIN0_MASK	LOONGSON_ADDRWINCFG(0x80)
+#define PCIDMA_WIN1_MASK	LOONGSON_ADDRWINCFG(0x88)
+#define PCIDMA_WIN2_MASK	LOONGSON_ADDRWINCFG(0x90)
+#define PCIDMA_WIN3_MASK	LOONGSON_ADDRWINCFG(0x98)
+
+#define PCIDMA_WIN0_MMAP	LOONGSON_ADDRWINCFG(0xa0)
+#define PCIDMA_WIN1_MMAP	LOONGSON_ADDRWINCFG(0xa8)
+#define PCIDMA_WIN2_MMAP	LOONGSON_ADDRWINCFG(0xb0)
+#define PCIDMA_WIN3_MMAP	LOONGSON_ADDRWINCFG(0xb8)
+
+#define ADDRWIN_WIN0	0
+#define ADDRWIN_WIN1	1
+#define ADDRWIN_WIN2	2
+#define ADDRWIN_WIN3	3
+
+#define ADDRWIN_MAP_DST_DDR	0
+#define ADDRWIN_MAP_DST_PCI	1
+#define ADDRWIN_MAP_DST_LIO	1
+
+/*
+ * s: CPU, PCIDMA
+ * d: DDR, PCI, LIO
+ * win: 0, 1, 2, 3
+ * src: map source
+ * dst: map destination
+ * size: ~mask + 1
+ */
+#define LOONGSON_ADDRWIN_CFG(s, d, w, src, dst, size) do {\
+	s##_WIN##w##_BASE = (src); \
+	s##_WIN##w##_MMAP = (dst) | ADDRWIN_MAP_DST_##d; \
+	s##_WIN##w##_MASK = ~(size-1); \
+} while (0)
+
+#define LOONGSON_ADDRWIN_CPUTOPCI(win, src, dst, size) \
+	LOONGSON_ADDRWIN_CFG(CPU, PCI, win, src, dst, size)
+#define LOONGSON_ADDRWIN_CPUTODDR(win, src, dst, size) \
+	LOONGSON_ADDRWIN_CFG(CPU, DDR, win, src, dst, size)
+#define LOONGSON_ADDRWIN_PCITODDR(win, src, dst, size) \
+	LOONGSON_ADDRWIN_CFG(PCIDMA, DDR, win, src, dst, size)
+
+#endif	/* ! CONFIG_CPU_SUPPORTS_ADDRWINCFG */
+
+#endif /* __ASM_MACH_LOONGSON2EF_LOONGSON_H */
diff --git a/arch/mips/include/asm/mach-loongson2ef/machine.h b/arch/mips/include/asm/mach-loongson2ef/machine.h
new file mode 100644
index 000000000..4097267ef
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson2ef/machine.h
@@ -0,0 +1,23 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2009 Lemote, Inc.
+ * Author: Wu Zhangjin <wuzhangjin@gmail.com>
+ */
+
+#ifndef __ASM_MACH_LOONGSON2EF_MACHINE_H
+#define __ASM_MACH_LOONGSON2EF_MACHINE_H
+
+#ifdef CONFIG_LEMOTE_FULOONG2E
+
+#define LOONGSON_MACHTYPE MACH_LEMOTE_FL2E
+
+#endif
+
+/* use fuloong2f as the default machine of LEMOTE_MACH2F */
+#ifdef CONFIG_LEMOTE_MACH2F
+
+#define LOONGSON_MACHTYPE MACH_LEMOTE_FL2F
+
+#endif
+
+#endif /* __ASM_MACH_LOONGSON2EF_MACHINE_H */
diff --git a/arch/mips/include/asm/mach-loongson2ef/mem.h b/arch/mips/include/asm/mach-loongson2ef/mem.h
new file mode 100644
index 000000000..d1d759b89
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson2ef/mem.h
@@ -0,0 +1,37 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2009 Lemote, Inc.
+ * Author: Wu Zhangjin <wuzhangjin@gmail.com>
+ */
+
+#ifndef __ASM_MACH_LOONGSON2EF_MEM_H
+#define __ASM_MACH_LOONGSON2EF_MEM_H
+
+/*
+ * high memory space
+ *
+ * in loongson2e, starts from 512M
+ * in loongson2f, starts from 2G 256M
+ */
+#ifdef CONFIG_CPU_LOONGSON2E
+#define LOONGSON_HIGHMEM_START	0x20000000
+#else
+#define LOONGSON_HIGHMEM_START	0x90000000
+#endif
+
+/*
+ * the peripheral registers(MMIO):
+ *
+ * On the Lemote Loongson 2e system, reside between 0x1000:0000 and 0x2000:0000.
+ * On the Lemote Loongson 2f system, reside between 0x1000:0000 and 0x8000:0000.
+ */
+
+#define LOONGSON_MMIO_MEM_START 0x10000000
+
+#ifdef CONFIG_CPU_LOONGSON2E
+#define LOONGSON_MMIO_MEM_END	0x20000000
+#else
+#define LOONGSON_MMIO_MEM_END	0x80000000
+#endif
+
+#endif /* __ASM_MACH_LOONGSON2EF_MEM_H */
diff --git a/arch/mips/include/asm/mach-loongson2ef/pci.h b/arch/mips/include/asm/mach-loongson2ef/pci.h
new file mode 100644
index 000000000..5588c5bc5
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson2ef/pci.h
@@ -0,0 +1,46 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (c) 2008 Zhang Le <r0bertz@gentoo.org>
+ * Copyright (c) 2009 Wu Zhangjin <wuzhangjin@gmail.com>
+ */
+
+#ifndef __ASM_MACH_LOONGSON2EF_PCI_H_
+#define __ASM_MACH_LOONGSON2EF_PCI_H_
+
+extern struct pci_ops loongson_pci_ops;
+
+/* this is an offset from mips_io_port_base */
+#define LOONGSON_PCI_IO_START	0x00004000UL
+
+#ifdef CONFIG_CPU_SUPPORTS_ADDRWINCFG
+
+/*
+ * we use address window2 to map cpu address space to pci space
+ * window2: cpu [1G, 2G] -> pci [1G, 2G]
+ * why not use window 0 & 1? because they are used by cpu when booting.
+ * window0: cpu [0, 256M] -> ddr [0, 256M]
+ * window1: cpu [256M, 512M] -> pci [256M, 512M]
+ */
+
+/* the smallest LOONGSON_CPU_MEM_SRC can be 512M */
+#define LOONGSON_CPU_MEM_SRC	0x40000000ul		/* 1G */
+#define LOONGSON_PCI_MEM_DST	LOONGSON_CPU_MEM_SRC
+
+#define LOONGSON_PCI_MEM_START	LOONGSON_PCI_MEM_DST
+#define LOONGSON_PCI_MEM_END	(0x80000000ul-1)	/* 2G */
+
+#define MMAP_CPUTOPCI_SIZE	(LOONGSON_PCI_MEM_END - \
+					LOONGSON_PCI_MEM_START + 1)
+
+#else	/* loongson2f/32bit & loongson2e */
+
+/* this pci memory space is mapped by pcimap in pci.c */
+#define LOONGSON_PCI_MEM_START	LOONGSON_PCILO1_BASE
+#define LOONGSON_PCI_MEM_END	(LOONGSON_PCILO1_BASE + 0x04000000 * 2)
+
+/* this is an offset from mips_io_port_base */
+#define LOONGSON_PCI_IO_START	0x00004000UL
+
+#endif	/* !CONFIG_CPU_SUPPORTS_ADDRWINCFG */
+
+#endif /* !__ASM_MACH_LOONGSON2EF_PCI_H_ */
diff --git a/arch/mips/include/asm/mach-loongson2ef/spaces.h b/arch/mips/include/asm/mach-loongson2ef/spaces.h
new file mode 100644
index 000000000..ba4e8e9b6
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson2ef/spaces.h
@@ -0,0 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_MACH_LOONGSON2EF_SPACES_H_
+#define __ASM_MACH_LOONGSON2EF_SPACES_H_
+
+#if defined(CONFIG_64BIT)
+#define CAC_BASE        _AC(0x9800000000000000, UL)
+#endif /* CONFIG_64BIT */
+
+#include <asm/mach-generic/spaces.h>
+#endif
diff --git a/arch/mips/include/asm/mach-loongson32/cpufreq.h b/arch/mips/include/asm/mach-loongson32/cpufreq.h
new file mode 100644
index 000000000..e422a3288
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson32/cpufreq.h
@@ -0,0 +1,18 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (c) 2014 Zhang, Keguang <keguang.zhang@gmail.com>
+ *
+ * Loongson 1 CPUFreq platform support.
+ */
+
+#ifndef __ASM_MACH_LOONGSON32_CPUFREQ_H
+#define __ASM_MACH_LOONGSON32_CPUFREQ_H
+
+struct plat_ls1x_cpufreq {
+	const char	*clk_name;	/* CPU clk */
+	const char	*osc_clk_name;	/* OSC clk */
+	unsigned int	max_freq;	/* in kHz */
+	unsigned int	min_freq;	/* in kHz */
+};
+
+#endif /* __ASM_MACH_LOONGSON32_CPUFREQ_H */
diff --git a/arch/mips/include/asm/mach-loongson32/dma.h b/arch/mips/include/asm/mach-loongson32/dma.h
new file mode 100644
index 000000000..e917b3ccb
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson32/dma.h
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (c) 2015 Zhang, Keguang <keguang.zhang@gmail.com>
+ *
+ * Loongson 1 NAND platform support.
+ */
+
+#ifndef __ASM_MACH_LOONGSON32_DMA_H
+#define __ASM_MACH_LOONGSON32_DMA_H
+
+#define LS1X_DMA_CHANNEL0	0
+#define LS1X_DMA_CHANNEL1	1
+#define LS1X_DMA_CHANNEL2	2
+
+struct plat_ls1x_dma {
+	int nr_channels;
+};
+
+extern struct plat_ls1x_dma ls1b_dma_pdata;
+
+#endif /* __ASM_MACH_LOONGSON32_DMA_H */
diff --git a/arch/mips/include/asm/mach-loongson32/irq.h b/arch/mips/include/asm/mach-loongson32/irq.h
new file mode 100644
index 000000000..6115f025b
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson32/irq.h
@@ -0,0 +1,107 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (c) 2011 Zhang, Keguang <keguang.zhang@gmail.com>
+ *
+ * IRQ mappings for Loongson 1
+ */
+
+#ifndef __ASM_MACH_LOONGSON32_IRQ_H
+#define __ASM_MACH_LOONGSON32_IRQ_H
+
+/*
+ * CPU core Interrupt Numbers
+ */
+#define MIPS_CPU_IRQ_BASE		0
+#define MIPS_CPU_IRQ(x)			(MIPS_CPU_IRQ_BASE + (x))
+
+#define SOFTINT0_IRQ			MIPS_CPU_IRQ(0)
+#define SOFTINT1_IRQ			MIPS_CPU_IRQ(1)
+#define INT0_IRQ			MIPS_CPU_IRQ(2)
+#define INT1_IRQ			MIPS_CPU_IRQ(3)
+#define INT2_IRQ			MIPS_CPU_IRQ(4)
+#define INT3_IRQ			MIPS_CPU_IRQ(5)
+#define INT4_IRQ			MIPS_CPU_IRQ(6)
+#define TIMER_IRQ			MIPS_CPU_IRQ(7)		/* cpu timer */
+
+#define MIPS_CPU_IRQS		(MIPS_CPU_IRQ(7) + 1 - MIPS_CPU_IRQ_BASE)
+
+/*
+ * INT0~3 Interrupt Numbers
+ */
+#define LS1X_IRQ_BASE			MIPS_CPU_IRQS
+#define LS1X_IRQ(n, x)			(LS1X_IRQ_BASE + (n << 5) + (x))
+
+#define LS1X_UART0_IRQ			LS1X_IRQ(0, 2)
+#if defined(CONFIG_LOONGSON1_LS1B)
+#define LS1X_UART1_IRQ			LS1X_IRQ(0, 3)
+#define LS1X_UART2_IRQ			LS1X_IRQ(0, 4)
+#define LS1X_UART3_IRQ			LS1X_IRQ(0, 5)
+#elif defined(CONFIG_LOONGSON1_LS1C)
+#define LS1X_UART1_IRQ			LS1X_IRQ(0, 4)
+#define LS1X_UART2_IRQ			LS1X_IRQ(0, 5)
+#endif
+#define LS1X_CAN0_IRQ			LS1X_IRQ(0, 6)
+#define LS1X_CAN1_IRQ			LS1X_IRQ(0, 7)
+#define LS1X_SPI0_IRQ			LS1X_IRQ(0, 8)
+#define LS1X_SPI1_IRQ			LS1X_IRQ(0, 9)
+#define LS1X_AC97_IRQ			LS1X_IRQ(0, 10)
+#define LS1X_DMA0_IRQ			LS1X_IRQ(0, 13)
+#define LS1X_DMA1_IRQ			LS1X_IRQ(0, 14)
+#define LS1X_DMA2_IRQ			LS1X_IRQ(0, 15)
+#if defined(CONFIG_LOONGSON1_LS1C)
+#define LS1X_NAND_IRQ			LS1X_IRQ(0, 16)
+#endif
+#define LS1X_PWM0_IRQ			LS1X_IRQ(0, 17)
+#define LS1X_PWM1_IRQ			LS1X_IRQ(0, 18)
+#define LS1X_PWM2_IRQ			LS1X_IRQ(0, 19)
+#define LS1X_PWM3_IRQ			LS1X_IRQ(0, 20)
+#define LS1X_RTC_INT0_IRQ		LS1X_IRQ(0, 21)
+#define LS1X_RTC_INT1_IRQ		LS1X_IRQ(0, 22)
+#define LS1X_RTC_INT2_IRQ		LS1X_IRQ(0, 23)
+#if defined(CONFIG_LOONGSON1_LS1B)
+#define LS1X_TOY_INT0_IRQ		LS1X_IRQ(0, 24)
+#define LS1X_TOY_INT1_IRQ		LS1X_IRQ(0, 25)
+#define LS1X_TOY_INT2_IRQ		LS1X_IRQ(0, 26)
+#define LS1X_RTC_TICK_IRQ		LS1X_IRQ(0, 27)
+#define LS1X_TOY_TICK_IRQ		LS1X_IRQ(0, 28)
+#define LS1X_UART4_IRQ			LS1X_IRQ(0, 29)
+#define LS1X_UART5_IRQ			LS1X_IRQ(0, 30)
+#elif defined(CONFIG_LOONGSON1_LS1C)
+#define LS1X_UART3_IRQ			LS1X_IRQ(0, 29)
+#define LS1X_ADC_IRQ			LS1X_IRQ(0, 30)
+#define LS1X_SDIO_IRQ			LS1X_IRQ(0, 31)
+#endif
+
+#define LS1X_EHCI_IRQ			LS1X_IRQ(1, 0)
+#define LS1X_OHCI_IRQ			LS1X_IRQ(1, 1)
+#if defined(CONFIG_LOONGSON1_LS1B)
+#define LS1X_GMAC0_IRQ			LS1X_IRQ(1, 2)
+#define LS1X_GMAC1_IRQ			LS1X_IRQ(1, 3)
+#elif defined(CONFIG_LOONGSON1_LS1C)
+#define LS1X_OTG_IRQ			LS1X_IRQ(1, 2)
+#define LS1X_GMAC0_IRQ			LS1X_IRQ(1, 3)
+#define LS1X_CAM_IRQ			LS1X_IRQ(1, 4)
+#define LS1X_UART4_IRQ			LS1X_IRQ(1, 5)
+#define LS1X_UART5_IRQ			LS1X_IRQ(1, 6)
+#define LS1X_UART6_IRQ			LS1X_IRQ(1, 7)
+#define LS1X_UART7_IRQ			LS1X_IRQ(1, 8)
+#define LS1X_UART8_IRQ			LS1X_IRQ(1, 9)
+#define LS1X_UART9_IRQ			LS1X_IRQ(1, 13)
+#define LS1X_UART10_IRQ			LS1X_IRQ(1, 14)
+#define LS1X_UART11_IRQ			LS1X_IRQ(1, 15)
+#define LS1X_I2C0_IRQ			LS1X_IRQ(1, 17)
+#define LS1X_I2C1_IRQ			LS1X_IRQ(1, 18)
+#define LS1X_I2C2_IRQ			LS1X_IRQ(1, 19)
+#endif
+
+#if defined(CONFIG_LOONGSON1_LS1B)
+#define INTN	4
+#elif defined(CONFIG_LOONGSON1_LS1C)
+#define INTN	5
+#endif
+
+#define LS1X_IRQS		(LS1X_IRQ(INTN, 31) + 1 - LS1X_IRQ_BASE)
+
+#define NR_IRQS			(MIPS_CPU_IRQS + LS1X_IRQS)
+
+#endif /* __ASM_MACH_LOONGSON32_IRQ_H */
diff --git a/arch/mips/include/asm/mach-loongson32/loongson1.h b/arch/mips/include/asm/mach-loongson32/loongson1.h
new file mode 100644
index 000000000..eb3ddbec1
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson32/loongson1.h
@@ -0,0 +1,54 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (c) 2011 Zhang, Keguang <keguang.zhang@gmail.com>
+ *
+ * Register mappings for Loongson 1
+ */
+
+#ifndef __ASM_MACH_LOONGSON32_LOONGSON1_H
+#define __ASM_MACH_LOONGSON32_LOONGSON1_H
+
+#if defined(CONFIG_LOONGSON1_LS1B)
+#define DEFAULT_MEMSIZE			64	/* If no memsize provided */
+#elif defined(CONFIG_LOONGSON1_LS1C)
+#define DEFAULT_MEMSIZE			32
+#endif
+
+/* Loongson 1 Register Bases */
+#define LS1X_MUX_BASE			0x1fd00420
+#define LS1X_INTC_BASE			0x1fd01040
+#define LS1X_GPIO0_BASE			0x1fd010c0
+#define LS1X_GPIO1_BASE			0x1fd010c4
+#define LS1X_DMAC_BASE			0x1fd01160
+#define LS1X_CBUS_BASE			0x1fd011c0
+#define LS1X_EHCI_BASE			0x1fe00000
+#define LS1X_OHCI_BASE			0x1fe08000
+#define LS1X_GMAC0_BASE			0x1fe10000
+#define LS1X_GMAC1_BASE			0x1fe20000
+
+#define LS1X_UART0_BASE			0x1fe40000
+#define LS1X_UART1_BASE			0x1fe44000
+#define LS1X_UART2_BASE			0x1fe48000
+#define LS1X_UART3_BASE			0x1fe4c000
+#define LS1X_CAN0_BASE			0x1fe50000
+#define LS1X_CAN1_BASE			0x1fe54000
+#define LS1X_I2C0_BASE			0x1fe58000
+#define LS1X_I2C1_BASE			0x1fe68000
+#define LS1X_I2C2_BASE			0x1fe70000
+#define LS1X_PWM0_BASE			0x1fe5c000
+#define LS1X_PWM1_BASE			0x1fe5c010
+#define LS1X_PWM2_BASE			0x1fe5c020
+#define LS1X_PWM3_BASE			0x1fe5c030
+#define LS1X_WDT_BASE			0x1fe5c060
+#define LS1X_RTC_BASE			0x1fe64000
+#define LS1X_AC97_BASE			0x1fe74000
+#define LS1X_NAND_BASE			0x1fe78000
+#define LS1X_CLK_BASE			0x1fe78030
+
+#include <regs-clk.h>
+#include <regs-mux.h>
+#include <regs-pwm.h>
+#include <regs-rtc.h>
+#include <regs-wdt.h>
+
+#endif /* __ASM_MACH_LOONGSON32_LOONGSON1_H */
diff --git a/arch/mips/include/asm/mach-loongson32/nand.h b/arch/mips/include/asm/mach-loongson32/nand.h
new file mode 100644
index 000000000..aaf5ed19d
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson32/nand.h
@@ -0,0 +1,26 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (c) 2015 Zhang, Keguang <keguang.zhang@gmail.com>
+ *
+ * Loongson 1 NAND platform support.
+ */
+
+#ifndef __ASM_MACH_LOONGSON32_NAND_H
+#define __ASM_MACH_LOONGSON32_NAND_H
+
+#include <linux/dmaengine.h>
+#include <linux/mtd/partitions.h>
+
+struct plat_ls1x_nand {
+	struct mtd_partition *parts;
+	unsigned int nr_parts;
+
+	int hold_cycle;
+	int wait_cycle;
+};
+
+extern struct plat_ls1x_nand ls1b_nand_pdata;
+
+bool ls1x_dma_filter_fn(struct dma_chan *chan, void *param);
+
+#endif /* __ASM_MACH_LOONGSON32_NAND_H */
diff --git a/arch/mips/include/asm/mach-loongson32/platform.h b/arch/mips/include/asm/mach-loongson32/platform.h
new file mode 100644
index 000000000..eb83e2741
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson32/platform.h
@@ -0,0 +1,28 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (c) 2011 Zhang, Keguang <keguang.zhang@gmail.com>
+ */
+
+#ifndef __ASM_MACH_LOONGSON32_PLATFORM_H
+#define __ASM_MACH_LOONGSON32_PLATFORM_H
+
+#include <linux/platform_device.h>
+
+#include <dma.h>
+#include <nand.h>
+
+extern struct platform_device ls1x_uart_pdev;
+extern struct platform_device ls1x_cpufreq_pdev;
+extern struct platform_device ls1x_eth0_pdev;
+extern struct platform_device ls1x_eth1_pdev;
+extern struct platform_device ls1x_ehci_pdev;
+extern struct platform_device ls1x_gpio0_pdev;
+extern struct platform_device ls1x_gpio1_pdev;
+extern struct platform_device ls1x_rtc_pdev;
+extern struct platform_device ls1x_wdt_pdev;
+
+void __init ls1x_clk_init(void);
+void __init ls1x_rtc_set_extclk(struct platform_device *pdev);
+void __init ls1x_serial_set_uartclk(struct platform_device *pdev);
+
+#endif /* __ASM_MACH_LOONGSON32_PLATFORM_H */
diff --git a/arch/mips/include/asm/mach-loongson32/regs-clk.h b/arch/mips/include/asm/mach-loongson32/regs-clk.h
new file mode 100644
index 000000000..98136fa8b
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson32/regs-clk.h
@@ -0,0 +1,81 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (c) 2011 Zhang, Keguang <keguang.zhang@gmail.com>
+ *
+ * Loongson 1 Clock Register Definitions.
+ */
+
+#ifndef __ASM_MACH_LOONGSON32_REGS_CLK_H
+#define __ASM_MACH_LOONGSON32_REGS_CLK_H
+
+#define LS1X_CLK_REG(x) \
+		((void __iomem *)KSEG1ADDR(LS1X_CLK_BASE + (x)))
+
+#define LS1X_CLK_PLL_FREQ		LS1X_CLK_REG(0x0)
+#define LS1X_CLK_PLL_DIV		LS1X_CLK_REG(0x4)
+
+#if defined(CONFIG_LOONGSON1_LS1B)
+/* Clock PLL Divisor Register Bits */
+#define DIV_DC_EN			BIT(31)
+#define DIV_DC_RST			BIT(30)
+#define DIV_CPU_EN			BIT(25)
+#define DIV_CPU_RST			BIT(24)
+#define DIV_DDR_EN			BIT(19)
+#define DIV_DDR_RST			BIT(18)
+#define RST_DC_EN			BIT(5)
+#define RST_DC				BIT(4)
+#define RST_DDR_EN			BIT(3)
+#define RST_DDR				BIT(2)
+#define RST_CPU_EN			BIT(1)
+#define RST_CPU				BIT(0)
+
+#define DIV_DC_SHIFT			26
+#define DIV_CPU_SHIFT			20
+#define DIV_DDR_SHIFT			14
+
+#define DIV_DC_WIDTH			4
+#define DIV_CPU_WIDTH			4
+#define DIV_DDR_WIDTH			4
+
+#define BYPASS_DC_SHIFT			12
+#define BYPASS_DDR_SHIFT		10
+#define BYPASS_CPU_SHIFT		8
+
+#define BYPASS_DC_WIDTH			1
+#define BYPASS_DDR_WIDTH		1
+#define BYPASS_CPU_WIDTH		1
+
+#elif defined(CONFIG_LOONGSON1_LS1C)
+/* PLL/SDRAM Frequency configuration register Bits */
+#define PLL_VALID			BIT(31)
+#define FRAC_N				GENMASK(23, 16)
+#define RST_TIME			GENMASK(3, 2)
+#define SDRAM_DIV			GENMASK(1, 0)
+
+/* CPU/CAMERA/DC Frequency configuration register Bits */
+#define DIV_DC_EN			BIT(31)
+#define DIV_DC				GENMASK(30, 24)
+#define DIV_CAM_EN			BIT(23)
+#define DIV_CAM				GENMASK(22, 16)
+#define DIV_CPU_EN			BIT(15)
+#define DIV_CPU				GENMASK(14, 8)
+#define DIV_DC_SEL_EN			BIT(5)
+#define DIV_DC_SEL			BIT(4)
+#define DIV_CAM_SEL_EN			BIT(3)
+#define DIV_CAM_SEL			BIT(2)
+#define DIV_CPU_SEL_EN			BIT(1)
+#define DIV_CPU_SEL			BIT(0)
+
+#define DIV_DC_SHIFT			24
+#define DIV_CAM_SHIFT			16
+#define DIV_CPU_SHIFT			8
+#define DIV_DDR_SHIFT			0
+
+#define DIV_DC_WIDTH			7
+#define DIV_CAM_WIDTH			7
+#define DIV_CPU_WIDTH			7
+#define DIV_DDR_WIDTH			2
+
+#endif
+
+#endif /* __ASM_MACH_LOONGSON32_REGS_CLK_H */
diff --git a/arch/mips/include/asm/mach-loongson32/regs-mux.h b/arch/mips/include/asm/mach-loongson32/regs-mux.h
new file mode 100644
index 000000000..95788a4f0
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson32/regs-mux.h
@@ -0,0 +1,124 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (c) 2014 Zhang, Keguang <keguang.zhang@gmail.com>
+ *
+ * Loongson 1 MUX Register Definitions.
+ */
+
+#ifndef __ASM_MACH_LOONGSON32_REGS_MUX_H
+#define __ASM_MACH_LOONGSON32_REGS_MUX_H
+
+#define LS1X_MUX_REG(x) \
+		((void __iomem *)KSEG1ADDR(LS1X_MUX_BASE + (x)))
+
+#define LS1X_MUX_CTRL0			LS1X_MUX_REG(0x0)
+#define LS1X_MUX_CTRL1			LS1X_MUX_REG(0x4)
+
+#if defined(CONFIG_LOONGSON1_LS1B)
+/* MUX CTRL0 Register Bits */
+#define UART0_USE_PWM23			BIT(28)
+#define UART0_USE_PWM01			BIT(27)
+#define UART1_USE_LCD0_5_6_11		BIT(26)
+#define I2C2_USE_CAN1			BIT(25)
+#define I2C1_USE_CAN0			BIT(24)
+#define NAND3_USE_UART5			BIT(23)
+#define NAND3_USE_UART4			BIT(22)
+#define NAND3_USE_UART1_DAT		BIT(21)
+#define NAND3_USE_UART1_CTS		BIT(20)
+#define NAND3_USE_PWM23			BIT(19)
+#define NAND3_USE_PWM01			BIT(18)
+#define NAND2_USE_UART5			BIT(17)
+#define NAND2_USE_UART4			BIT(16)
+#define NAND2_USE_UART1_DAT		BIT(15)
+#define NAND2_USE_UART1_CTS		BIT(14)
+#define NAND2_USE_PWM23			BIT(13)
+#define NAND2_USE_PWM01			BIT(12)
+#define NAND1_USE_UART5			BIT(11)
+#define NAND1_USE_UART4			BIT(10)
+#define NAND1_USE_UART1_DAT		BIT(9)
+#define NAND1_USE_UART1_CTS		BIT(8)
+#define NAND1_USE_PWM23			BIT(7)
+#define NAND1_USE_PWM01			BIT(6)
+#define GMAC1_USE_UART1			BIT(4)
+#define GMAC1_USE_UART0			BIT(3)
+#define LCD_USE_UART0_DAT		BIT(2)
+#define LCD_USE_UART15			BIT(1)
+#define LCD_USE_UART0			BIT(0)
+
+/* MUX CTRL1 Register Bits */
+#define USB_RESET			BIT(31)
+#define SPI1_CS_USE_PWM01		BIT(24)
+#define SPI1_USE_CAN			BIT(23)
+#define DISABLE_DDR_CONFSPACE		BIT(20)
+#define DDR32TO16EN			BIT(16)
+#define GMAC1_SHUT			BIT(13)
+#define GMAC0_SHUT			BIT(12)
+#define USB_SHUT			BIT(11)
+#define UART1_3_USE_CAN1		BIT(5)
+#define UART1_2_USE_CAN0		BIT(4)
+#define GMAC1_USE_TXCLK			BIT(3)
+#define GMAC0_USE_TXCLK			BIT(2)
+#define GMAC1_USE_PWM23			BIT(1)
+#define GMAC0_USE_PWM01			BIT(0)
+
+#elif defined(CONFIG_LOONGSON1_LS1C)
+
+/* SHUT_CTRL Register Bits */
+#define UART_SPLIT			GENMASK(31, 30)
+#define OUTPUT_CLK			GENMASK(29, 26)
+#define ADC_SHUT			BIT(25)
+#define SDIO_SHUT			BIT(24)
+#define DMA2_SHUT			BIT(23)
+#define DMA1_SHUT			BIT(22)
+#define DMA0_SHUT			BIT(21)
+#define SPI1_SHUT			BIT(20)
+#define SPI0_SHUT			BIT(19)
+#define I2C2_SHUT			BIT(18)
+#define I2C1_SHUT			BIT(17)
+#define I2C0_SHUT			BIT(16)
+#define AC97_SHUT			BIT(15)
+#define I2S_SHUT			BIT(14)
+#define UART3_SHUT			BIT(13)
+#define UART2_SHUT			BIT(12)
+#define UART1_SHUT			BIT(11)
+#define UART0_SHUT			BIT(10)
+#define CAN1_SHUT			BIT(9)
+#define CAN0_SHUT			BIT(8)
+#define ECC_SHUT			BIT(7)
+#define GMAC_SHUT			BIT(6)
+#define USBHOST_SHUT			BIT(5)
+#define USBOTG_SHUT			BIT(4)
+#define SDRAM_SHUT			BIT(3)
+#define SRAM_SHUT			BIT(2)
+#define CAM_SHUT			BIT(1)
+#define LCD_SHUT			BIT(0)
+
+#define UART_SPLIT_SHIFT                        30
+#define OUTPUT_CLK_SHIFT                        26
+
+/* MISC_CTRL Register Bits */
+#define USBHOST_RSTN			BIT(31)
+#define PHY_INTF_SELI			GENMASK(30, 28)
+#define AC97_EN				BIT(25)
+#define SDIO_DMA_EN			GENMASK(24, 23)
+#define ADC_DMA_EN			BIT(22)
+#define SDIO_USE_SPI1			BIT(17)
+#define SDIO_USE_SPI0			BIT(16)
+#define SRAM_CTRL			GENMASK(15, 0)
+
+#define PHY_INTF_SELI_SHIFT                     28
+#define SDIO_DMA_EN_SHIFT                       23
+#define SRAM_CTRL_SHIFT				0
+
+#define LS1X_CBUS_REG(n, x) \
+		((void __iomem *)KSEG1ADDR(LS1X_CBUS_BASE + (n * 0x04) + (x)))
+
+#define LS1X_CBUS_FIRST(n)		LS1X_CBUS_REG(n, 0x00)
+#define LS1X_CBUS_SECOND(n)		LS1X_CBUS_REG(n, 0x10)
+#define LS1X_CBUS_THIRD(n)		LS1X_CBUS_REG(n, 0x20)
+#define LS1X_CBUS_FOURTHT(n)		LS1X_CBUS_REG(n, 0x30)
+#define LS1X_CBUS_FIFTHT(n)		LS1X_CBUS_REG(n, 0x40)
+
+#endif
+
+#endif /* __ASM_MACH_LOONGSON32_REGS_MUX_H */
diff --git a/arch/mips/include/asm/mach-loongson32/regs-pwm.h b/arch/mips/include/asm/mach-loongson32/regs-pwm.h
new file mode 100644
index 000000000..ec870c82d
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson32/regs-pwm.h
@@ -0,0 +1,25 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (c) 2014 Zhang, Keguang <keguang.zhang@gmail.com>
+ *
+ * Loongson 1 PWM Register Definitions.
+ */
+
+#ifndef __ASM_MACH_LOONGSON32_REGS_PWM_H
+#define __ASM_MACH_LOONGSON32_REGS_PWM_H
+
+/* Loongson 1 PWM Timer Register Definitions */
+#define PWM_CNT			0x0
+#define PWM_HRC			0x4
+#define PWM_LRC			0x8
+#define PWM_CTRL		0xc
+
+/* PWM Control Register Bits */
+#define CNT_RST			BIT(7)
+#define INT_SR			BIT(6)
+#define INT_EN			BIT(5)
+#define PWM_SINGLE		BIT(4)
+#define PWM_OE			BIT(3)
+#define CNT_EN			BIT(0)
+
+#endif /* __ASM_MACH_LOONGSON32_REGS_PWM_H */
diff --git a/arch/mips/include/asm/mach-loongson32/regs-rtc.h b/arch/mips/include/asm/mach-loongson32/regs-rtc.h
new file mode 100644
index 000000000..a3d096be1
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson32/regs-rtc.h
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (c) 2016 Yang Ling <gnaygnil@gmail.com>
+ *
+ * Loongson 1 RTC timer Register Definitions.
+ */
+
+#ifndef __ASM_MACH_LOONGSON32_REGS_RTC_H
+#define __ASM_MACH_LOONGSON32_REGS_RTC_H
+
+#define LS1X_RTC_REG(x) \
+		((void __iomem *)KSEG1ADDR(LS1X_RTC_BASE + (x)))
+
+#define LS1X_RTC_CTRL	LS1X_RTC_REG(0x40)
+
+#define RTC_EXTCLK_OK	(BIT(5) | BIT(8))
+#define RTC_EXTCLK_EN	BIT(8)
+
+#endif /* __ASM_MACH_LOONGSON32_REGS_RTC_H */
diff --git a/arch/mips/include/asm/mach-loongson32/regs-wdt.h b/arch/mips/include/asm/mach-loongson32/regs-wdt.h
new file mode 100644
index 000000000..c6d345fe1
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson32/regs-wdt.h
@@ -0,0 +1,15 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (c) 2011 Zhang, Keguang <keguang.zhang@gmail.com>
+ *
+ * Loongson 1 Watchdog Register Definitions.
+ */
+
+#ifndef __ASM_MACH_LOONGSON32_REGS_WDT_H
+#define __ASM_MACH_LOONGSON32_REGS_WDT_H
+
+#define WDT_EN			0x0
+#define WDT_TIMER		0x4
+#define WDT_SET			0x8
+
+#endif /* __ASM_MACH_LOONGSON32_REGS_WDT_H */
diff --git a/arch/mips/include/asm/mach-loongson64/boot_param.h b/arch/mips/include/asm/mach-loongson64/boot_param.h
new file mode 100644
index 000000000..e007edd6b
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson64/boot_param.h
@@ -0,0 +1,218 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_MACH_LOONGSON64_BOOT_PARAM_H_
+#define __ASM_MACH_LOONGSON64_BOOT_PARAM_H_
+
+#include <linux/types.h>
+
+#define SYSTEM_RAM_LOW		1
+#define SYSTEM_RAM_HIGH		2
+#define SYSTEM_RAM_RESERVED	3
+#define PCI_IO			4
+#define PCI_MEM			5
+#define LOONGSON_CFG_REG	6
+#define VIDEO_ROM		7
+#define ADAPTER_ROM		8
+#define ACPI_TABLE		9
+#define SMBIOS_TABLE		10
+#define UMA_VIDEO_RAM		11
+#define VUMA_VIDEO_RAM		12
+#define MAX_MEMORY_TYPE		13
+
+#define MEM_SIZE_IS_IN_BYTES	(1 << 31)
+
+#define LOONGSON3_BOOT_MEM_MAP_MAX 128
+struct efi_memory_map_loongson {
+	u16 vers;	/* version of efi_memory_map */
+	u32 nr_map;	/* number of memory_maps */
+	u32 mem_freq;	/* memory frequence */
+	struct mem_map {
+		u32 node_id;	/* node_id which memory attached to */
+		u32 mem_type;	/* system memory, pci memory, pci io, etc. */
+		u64 mem_start;	/* memory map start address */
+		u32 mem_size;	/* each memory_map size, not the total size */
+	} map[LOONGSON3_BOOT_MEM_MAP_MAX];
+} __packed;
+
+enum loongson_cpu_type {
+	Legacy_2E = 0x0,
+	Legacy_2F = 0x1,
+	Legacy_3A = 0x2,
+	Legacy_3B = 0x3,
+	Legacy_1A = 0x4,
+	Legacy_1B = 0x5,
+	Legacy_2G = 0x6,
+	Legacy_2H = 0x7,
+	Loongson_1A = 0x100,
+	Loongson_1B = 0x101,
+	Loongson_2E = 0x200,
+	Loongson_2F = 0x201,
+	Loongson_2G = 0x202,
+	Loongson_2H = 0x203,
+	Loongson_3A = 0x300,
+	Loongson_3B = 0x301
+};
+
+/*
+ * Capability and feature descriptor structure for MIPS CPU
+ */
+struct efi_cpuinfo_loongson {
+	u16 vers;     /* version of efi_cpuinfo_loongson */
+	u32 processor_id; /* PRID, e.g. 6305, 6306 */
+	u32 cputype;  /* Loongson_3A/3B, etc. */
+	u32 total_node;   /* num of total numa nodes */
+	u16 cpu_startup_core_id; /* Boot core id */
+	u16 reserved_cores_mask;
+	u32 cpu_clock_freq; /* cpu_clock */
+	u32 nr_cpus;
+} __packed;
+
+#define MAX_UARTS 64
+struct uart_device {
+	u32 iotype; /* see include/linux/serial_core.h */
+	u32 uartclk;
+	u32 int_offset;
+	u64 uart_base;
+} __packed;
+
+#define MAX_SENSORS 64
+#define SENSOR_TEMPER  0x00000001
+#define SENSOR_VOLTAGE 0x00000002
+#define SENSOR_FAN     0x00000004
+struct sensor_device {
+	char name[32];  /* a formal name */
+	char label[64]; /* a flexible description */
+	u32 type;       /* SENSOR_* */
+	u32 id;         /* instance id of a sensor-class */
+	u32 fan_policy; /* see loongson_hwmon.h */
+	u32 fan_percent;/* only for constant speed policy */
+	u64 base_addr;  /* base address of device registers */
+} __packed;
+
+struct system_loongson {
+	u16 vers;     /* version of system_loongson */
+	u32 ccnuma_smp; /* 0: no numa; 1: has numa */
+	u32 sing_double_channel; /* 1:single; 2:double */
+	u32 nr_uarts;
+	struct uart_device uarts[MAX_UARTS];
+	u32 nr_sensors;
+	struct sensor_device sensors[MAX_SENSORS];
+	char has_ec;
+	char ec_name[32];
+	u64 ec_base_addr;
+	char has_tcm;
+	char tcm_name[32];
+	u64 tcm_base_addr;
+	u64 workarounds; /* see workarounds.h */
+} __packed;
+
+struct irq_source_routing_table {
+	u16 vers;
+	u16 size;
+	u16 rtr_bus;
+	u16 rtr_devfn;
+	u32 vendor;
+	u32 device;
+	u32 PIC_type;   /* conform use HT or PCI to route to CPU-PIC */
+	u64 ht_int_bit; /* 3A: 1<<24; 3B: 1<<16 */
+	u64 ht_enable;  /* irqs used in this PIC */
+	u32 node_id;    /* node id: 0x0-0; 0x1-1; 0x10-2; 0x11-3 */
+	u64 pci_mem_start_addr;
+	u64 pci_mem_end_addr;
+	u64 pci_io_start_addr;
+	u64 pci_io_end_addr;
+	u64 pci_config_addr;
+	u16 dma_mask_bits;
+	u16 dma_noncoherent;
+} __packed;
+
+struct interface_info {
+	u16 vers; /* version of the specificition */
+	u16 size;
+	u8  flag;
+	char description[64];
+} __packed;
+
+#define MAX_RESOURCE_NUMBER 128
+struct resource_loongson {
+	u64 start; /* resource start address */
+	u64 end;   /* resource end address */
+	char name[64];
+	u32 flags;
+};
+
+struct archdev_data {};  /* arch specific additions */
+
+struct board_devices {
+	char name[64];    /* hold the device name */
+	u32 num_resources; /* number of device_resource */
+	/* for each device's resource */
+	struct resource_loongson resource[MAX_RESOURCE_NUMBER];
+	/* arch specific additions */
+	struct archdev_data archdata;
+};
+
+struct loongson_special_attribute {
+	u16 vers;     /* version of this special */
+	char special_name[64]; /* special_atribute_name */
+	u32 loongson_special_type; /* type of special device */
+	/* for each device's resource */
+	struct resource_loongson resource[MAX_RESOURCE_NUMBER];
+};
+
+struct loongson_params {
+	u64 memory_offset;	/* efi_memory_map_loongson struct offset */
+	u64 cpu_offset;		/* efi_cpuinfo_loongson struct offset */
+	u64 system_offset;	/* system_loongson struct offset */
+	u64 irq_offset;		/* irq_source_routing_table struct offset */
+	u64 interface_offset;	/* interface_info struct offset */
+	u64 special_offset;	/* loongson_special_attribute struct offset */
+	u64 boarddev_table_offset;  /* board_devices offset */
+};
+
+struct smbios_tables {
+	u16 vers;     /* version of smbios */
+	u64 vga_bios; /* vga_bios address */
+	struct loongson_params lp;
+};
+
+struct efi_reset_system_t {
+	u64 ResetCold;
+	u64 ResetWarm;
+	u64 ResetType;
+	u64 Shutdown;
+	u64 DoSuspend; /* NULL if not support */
+};
+
+struct efi_loongson {
+	u64 mps;	/* MPS table */
+	u64 acpi;	/* ACPI table (IA64 ext 0.71) */
+	u64 acpi20;	/* ACPI table (ACPI 2.0) */
+	struct smbios_tables smbios;	/* SM BIOS table */
+	u64 sal_systab;	/* SAL system table */
+	u64 boot_info;	/* boot info table */
+};
+
+struct boot_params {
+	struct efi_loongson efi;
+	struct efi_reset_system_t reset_system;
+};
+
+enum loongson_bridge_type {
+	LS7A = 1,
+	RS780E = 2,
+	VIRTUAL = 3
+};
+
+extern struct efi_memory_map_loongson *loongson_memmap;
+extern struct loongson_system_configuration loongson_sysconf;
+
+extern struct board_devices *eboard;
+extern struct interface_info *einter;
+extern struct loongson_special_attribute *especial;
+
+extern u32 node_id_offset;
+extern void ls7a_early_config(void);
+extern void rs780e_early_config(void);
+extern void virtual_early_config(void);
+
+#endif
diff --git a/arch/mips/include/asm/mach-loongson64/builtin_dtbs.h b/arch/mips/include/asm/mach-loongson64/builtin_dtbs.h
new file mode 100644
index 000000000..8be710557
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson64/builtin_dtbs.h
@@ -0,0 +1,17 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2019 Jiaxun Yang <jiaxun.yang@flygoat.com>
+ *
+ * Built-in Generic dtbs for MACH_LOONGSON64
+ */
+
+#ifndef __ASM_MACH_LOONGSON64_BUILTIN_DTBS_H_
+#define __ASM_MACH_LOONGSON64_BUILTIN_DTBS_H_
+
+extern u32 __dtb_loongson64_2core_2k1000_begin[];
+extern u32 __dtb_loongson64c_4core_ls7a_begin[];
+extern u32 __dtb_loongson64c_4core_rs780e_begin[];
+extern u32 __dtb_loongson64c_8core_rs780e_begin[];
+extern u32 __dtb_loongson64g_4core_ls7a_begin[];
+extern u32 __dtb_loongson64v_4core_virtio_begin[];
+#endif
diff --git a/arch/mips/include/asm/mach-loongson64/cpu-feature-overrides.h b/arch/mips/include/asm/mach-loongson64/cpu-feature-overrides.h
new file mode 100644
index 000000000..ebace9e4b
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson64/cpu-feature-overrides.h
@@ -0,0 +1,50 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2009 Wu Zhangjin <wuzhangjin@gmail.com>
+ * Copyright (C) 2009 Philippe Vachon <philippe@cowpig.ca>
+ * Copyright (C) 2009 Zhang Le <r0bertz@gentoo.org>
+ *
+ * reference: /proc/cpuinfo,
+ *	arch/mips/kernel/cpu-probe.c(cpu_probe_legacy),
+ *	arch/mips/kernel/proc.c(show_cpuinfo),
+ *	loongson2f user manual.
+ */
+
+#ifndef __ASM_MACH_LOONGSON64_CPU_FEATURE_OVERRIDES_H
+#define __ASM_MACH_LOONGSON64_CPU_FEATURE_OVERRIDES_H
+
+#define cpu_has_32fpr		1
+#define cpu_has_3k_cache	0
+#define cpu_has_4k_cache	1
+#define cpu_has_4kex		1
+#define cpu_has_64bits		1
+#define cpu_has_cache_cdex_p	0
+#define cpu_has_cache_cdex_s	0
+#define cpu_has_counter		1
+#define cpu_has_dc_aliases	(PAGE_SIZE < 0x4000)
+#define cpu_has_divec		0
+#define cpu_has_inclusive_pcaches	1
+#define cpu_has_llsc		1
+#define cpu_has_mcheck		0
+#define cpu_has_mdmx		0
+#define cpu_has_mips16		0
+#define cpu_has_mips16e2	0
+#define cpu_has_mips3d		0
+#define cpu_has_mipsmt		0
+#define cpu_has_smartmips	0
+#define cpu_has_tlb		1
+#define cpu_has_vce		0
+#define cpu_has_veic		0
+#define cpu_has_vint		0
+#define cpu_has_vtag_icache	0
+#define cpu_has_wsbh		1
+#define cpu_has_ic_fills_f_dc	1
+#define cpu_hwrena_impl_bits	0xc0000000
+#define cpu_has_mac2008_only	1
+#define cpu_has_mips_r2_exec_hazard 0
+#define cpu_has_perf_cntr_intr_bit	0
+
+#endif /* __ASM_MACH_LOONGSON64_CPU_FEATURE_OVERRIDES_H */
diff --git a/arch/mips/include/asm/mach-loongson64/cpucfg-emul.h b/arch/mips/include/asm/mach-loongson64/cpucfg-emul.h
new file mode 100644
index 000000000..d64af19c2
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson64/cpucfg-emul.h
@@ -0,0 +1,74 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _ASM_MACH_LOONGSON64_CPUCFG_EMUL_H_
+#define _ASM_MACH_LOONGSON64_CPUCFG_EMUL_H_
+
+#include <asm/cpu-info.h>
+
+#ifdef CONFIG_CPU_LOONGSON3_CPUCFG_EMULATION
+
+#include <loongson_regs.h>
+
+#define LOONGSON_FPREV_MASK 0x7
+
+void loongson3_cpucfg_synthesize_data(struct cpuinfo_mips *c);
+
+static inline bool loongson3_cpucfg_emulation_enabled(struct cpuinfo_mips *c)
+{
+	/* All supported cores have non-zero LOONGSON_CFG1 data. */
+	return c->loongson3_cpucfg_data[0] != 0;
+}
+
+static inline u32 loongson3_cpucfg_read_synthesized(struct cpuinfo_mips *c,
+	__u64 sel)
+{
+	switch (sel) {
+	case LOONGSON_CFG0:
+		return c->processor_id;
+	case LOONGSON_CFG1:
+	case LOONGSON_CFG2:
+	case LOONGSON_CFG3:
+		return c->loongson3_cpucfg_data[sel - 1];
+	case LOONGSON_CFG4:
+	case LOONGSON_CFG5:
+		/* CPUCFG selects 4 and 5 are related to the input clock
+		 * signal.
+		 *
+		 * Unimplemented for now.
+		 */
+		return 0;
+	case LOONGSON_CFG6:
+		/* CPUCFG select 6 is for the undocumented Safe Extension. */
+		return 0;
+	case LOONGSON_CFG7:
+		/* CPUCFG select 7 is for the virtualization extension.
+		 * We don't know if the two currently known features are
+		 * supported on older cores according to the public
+		 * documentation, so leave this at zero.
+		 */
+		return 0;
+	}
+
+	/*
+	 * Return 0 for unrecognized CPUCFG selects, which is real hardware
+	 * behavior observed on Loongson 3A R4.
+	 */
+	return 0;
+}
+#else
+static inline void loongson3_cpucfg_synthesize_data(struct cpuinfo_mips *c)
+{
+}
+
+static inline bool loongson3_cpucfg_emulation_enabled(struct cpuinfo_mips *c)
+{
+	return false;
+}
+
+static inline u32 loongson3_cpucfg_read_synthesized(struct cpuinfo_mips *c,
+	__u64 sel)
+{
+	return 0;
+}
+#endif
+
+#endif /* _ASM_MACH_LOONGSON64_CPUCFG_EMUL_H_ */
diff --git a/arch/mips/include/asm/mach-loongson64/irq.h b/arch/mips/include/asm/mach-loongson64/irq.h
new file mode 100644
index 000000000..67c15f320
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson64/irq.h
@@ -0,0 +1,16 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_MACH_LOONGSON64_IRQ_H_
+#define __ASM_MACH_LOONGSON64_IRQ_H_
+
+/* cpu core interrupt numbers */
+#define NR_IRQS_LEGACY		16
+#define NR_MIPS_CPU_IRQS	8
+#define NR_MAX_CHAINED_IRQS	40 /* Chained IRQs means those not directly used by devices */
+#define NR_IRQS			(NR_IRQS_LEGACY + NR_MIPS_CPU_IRQS + NR_MAX_CHAINED_IRQS + 256)
+#define MAX_IO_PICS		1
+#define MIPS_CPU_IRQ_BASE 	NR_IRQS_LEGACY
+#define GSI_MIN_CPU_IRQ		0
+
+#include <asm/mach-generic/irq.h>
+
+#endif /* __ASM_MACH_LOONGSON64_IRQ_H_ */
diff --git a/arch/mips/include/asm/mach-loongson64/kernel-entry-init.h b/arch/mips/include/asm/mach-loongson64/kernel-entry-init.h
new file mode 100644
index 000000000..efb41b351
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson64/kernel-entry-init.h
@@ -0,0 +1,105 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2005 Embedded Alley Solutions, Inc
+ * Copyright (C) 2005 Ralf Baechle (ralf@linux-mips.org)
+ * Copyright (C) 2009 Jiajie Chen (chenjiajie@cse.buaa.edu.cn)
+ * Copyright (C) 2012 Huacai Chen (chenhc@lemote.com)
+ */
+#ifndef __ASM_MACH_LOONGSON64_KERNEL_ENTRY_H
+#define __ASM_MACH_LOONGSON64_KERNEL_ENTRY_H
+
+#include <asm/cpu.h>
+
+/*
+ * Override macros used in arch/mips/kernel/head.S.
+ */
+	.macro	kernel_entry_setup
+	.set	push
+	.set	mips64
+	/* Set ELPA on LOONGSON3 pagegrain */
+	mfc0	t0, CP0_PAGEGRAIN
+	or	t0, (0x1 << 29)
+	mtc0	t0, CP0_PAGEGRAIN
+	/* Enable STFill Buffer */
+	mfc0	t0, CP0_PRID
+	/* Loongson-3A R4+ */
+	andi	t1, t0, PRID_IMP_MASK
+	li	t2, PRID_IMP_LOONGSON_64G
+	beq     t1, t2, 1f
+	nop
+	/* Loongson-3A R2/R3 */
+	andi	t0, (PRID_IMP_MASK | PRID_REV_MASK)
+	slti	t0, t0, (PRID_IMP_LOONGSON_64C | PRID_REV_LOONGSON3A_R2_0)
+	bnez	t0, 2f
+	nop
+1:
+	mfc0	t0, CP0_CONFIG6
+	or	t0, 0x100
+	mtc0	t0, CP0_CONFIG6
+2:
+	_ehb
+	.set	pop
+	.endm
+
+/*
+ * Do SMP slave processor setup.
+ */
+	.macro	smp_slave_setup
+	.set	push
+	.set	mips64
+	/* Set ELPA on LOONGSON3 pagegrain */
+	mfc0	t0, CP0_PAGEGRAIN
+	or	t0, (0x1 << 29)
+	mtc0	t0, CP0_PAGEGRAIN
+	/* Enable STFill Buffer */
+	mfc0	t0, CP0_PRID
+	/* Loongson-3A R4+ */
+	andi	t1, t0, PRID_IMP_MASK
+	li	t2, PRID_IMP_LOONGSON_64G
+	beq     t1, t2, 1f
+	nop
+	/* Loongson-3A R2/R3 */
+	andi	t0, (PRID_IMP_MASK | PRID_REV_MASK)
+	slti	t0, t0, (PRID_IMP_LOONGSON_64C | PRID_REV_LOONGSON3A_R2_0)
+	bnez	t0, 2f
+	nop
+1:
+	mfc0	t0, CP0_CONFIG6
+	or	t0, 0x100
+	mtc0	t0, CP0_CONFIG6
+2:
+	_ehb
+	.set	pop
+	.endm
+
+#define USE_KEXEC_SMP_WAIT_FINAL
+	.macro  kexec_smp_wait_final
+	/* s0:prid s1:initfn */
+	/* a0:base t1:cpuid t2:node t9:count */
+	mfc0		t1, CP0_EBASE
+	andi		t1, MIPS_EBASE_CPUNUM
+	dins		a0, t1, 8, 2       /* insert core id*/
+	dext		t2, t1, 2, 2
+	dins		a0, t2, 44, 2      /* insert node id */
+	mfc0		s0, CP0_PRID
+	andi		s0, s0, (PRID_IMP_MASK | PRID_REV_MASK)
+	beq		s0, (PRID_IMP_LOONGSON_64C | PRID_REV_LOONGSON3B_R1), 1f
+	beq		s0, (PRID_IMP_LOONGSON_64C | PRID_REV_LOONGSON3B_R2), 1f
+	b		2f                 /* Loongson-3A1000/3A2000/3A3000/3A4000 */
+1:	dins		a0, t2, 14, 2      /* Loongson-3B1000/3B1500 need bit 15~14 */
+2:	li		t9, 0x100          /* wait for init loop */
+3:	addiu		t9, -1             /* limit mailbox access */
+	bnez		t9, 3b
+	lw		s1, 0x20(a0)       /* check PC as an indicator */
+	beqz		s1, 2b
+	ld		s1, 0x20(a0)       /* get PC via mailbox reg0 */
+	ld		sp, 0x28(a0)       /* get SP via mailbox reg1 */
+	ld		gp, 0x30(a0)       /* get GP via mailbox reg2 */
+	ld		a1, 0x38(a0)
+	jr		s1                 /* jump to initial PC */
+	.endm
+
+#endif /* __ASM_MACH_LOONGSON64_KERNEL_ENTRY_H */
diff --git a/arch/mips/include/asm/mach-loongson64/loongson.h b/arch/mips/include/asm/mach-loongson64/loongson.h
new file mode 100644
index 000000000..f7c3ab6d7
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson64/loongson.h
@@ -0,0 +1,266 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2009 Lemote, Inc.
+ * Author: Wu Zhangjin <wuzhangjin@gmail.com>
+ */
+
+#ifndef __ASM_MACH_LOONGSON64_LOONGSON_H
+#define __ASM_MACH_LOONGSON64_LOONGSON_H
+
+#include <linux/io.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <boot_param.h>
+
+enum loongson_fw_interface {
+	LOONGSON_LEFI,
+	LOONGSON_DTB,
+};
+
+/* machine-specific boot configuration */
+struct loongson_system_configuration {
+	enum loongson_fw_interface fw_interface;
+	u32 nr_cpus;
+	u32 nr_nodes;
+	int cores_per_node;
+	int cores_per_package;
+	u16 boot_cpu_id;
+	u16 reserved_cpus_mask;
+	enum loongson_cpu_type cputype;
+	enum loongson_bridge_type bridgetype;
+	u64 restart_addr;
+	u64 poweroff_addr;
+	u64 suspend_addr;
+	u64 vgabios_addr;
+	u32 dma_mask_bits;
+	u64 workarounds;
+	void (*early_config)(void);
+};
+
+/* machine-specific reboot/halt operation */
+extern void mach_prepare_reboot(void);
+extern void mach_prepare_shutdown(void);
+
+/* environment arguments from bootloader */
+extern u32 cpu_clock_freq;
+extern u32 memsize, highmemsize;
+extern const struct plat_smp_ops loongson3_smp_ops;
+
+/* loongson-specific command line, env and memory initialization */
+extern void __init prom_dtb_init_env(void);
+extern void __init prom_lefi_init_env(void);
+extern void __init szmem(unsigned int node);
+extern void *loongson_fdt_blob;
+
+/* irq operation functions */
+extern void mach_irq_dispatch(unsigned int pending);
+extern int mach_i8259_irq(void);
+
+/* We need this in some places... */
+#define delay() ({		\
+	int x;				\
+	for (x = 0; x < 100000; x++)	\
+		__asm__ __volatile__(""); \
+})
+
+#define LOONGSON_REG(x) \
+	(*(volatile u32 *)((char *)CKSEG1ADDR(LOONGSON_REG_BASE) + (x)))
+
+#define LOONGSON3_REG8(base, x) \
+	(*(volatile u8 *)((char *)TO_UNCAC(base) + (x)))
+
+#define LOONGSON3_REG32(base, x) \
+	(*(volatile u32 *)((char *)TO_UNCAC(base) + (x)))
+
+#define LOONGSON_FLASH_BASE	0x1c000000
+#define LOONGSON_FLASH_SIZE	0x02000000	/* 32M */
+#define LOONGSON_FLASH_TOP	(LOONGSON_FLASH_BASE+LOONGSON_FLASH_SIZE-1)
+
+#define LOONGSON_LIO0_BASE	0x1e000000
+#define LOONGSON_LIO0_SIZE	0x01C00000	/* 28M */
+#define LOONGSON_LIO0_TOP	(LOONGSON_LIO0_BASE+LOONGSON_LIO0_SIZE-1)
+
+#define LOONGSON_BOOT_BASE	0x1fc00000
+#define LOONGSON_BOOT_SIZE	0x00100000	/* 1M */
+#define LOONGSON_BOOT_TOP	(LOONGSON_BOOT_BASE+LOONGSON_BOOT_SIZE-1)
+#define LOONGSON_REG_BASE	0x1fe00000
+#define LOONGSON_REG_SIZE	0x00100000	/* 256Bytes + 256Bytes + ??? */
+#define LOONGSON_REG_TOP	(LOONGSON_REG_BASE+LOONGSON_REG_SIZE-1)
+/* Loongson-3 specific registers */
+#define LOONGSON3_REG_BASE	0x3ff00000
+#define LOONGSON3_REG_SIZE	0x00100000	/* 256Bytes + 256Bytes + ??? */
+#define LOONGSON3_REG_TOP	(LOONGSON3_REG_BASE+LOONGSON3_REG_SIZE-1)
+
+#define LOONGSON_LIO1_BASE	0x1ff00000
+#define LOONGSON_LIO1_SIZE	0x00100000	/* 1M */
+#define LOONGSON_LIO1_TOP	(LOONGSON_LIO1_BASE+LOONGSON_LIO1_SIZE-1)
+
+#define LOONGSON_PCILO0_BASE	0x10000000
+#define LOONGSON_PCILO1_BASE	0x14000000
+#define LOONGSON_PCILO2_BASE	0x18000000
+#define LOONGSON_PCILO_BASE	LOONGSON_PCILO0_BASE
+#define LOONGSON_PCILO_SIZE	0x0c000000	/* 64M * 3 */
+#define LOONGSON_PCILO_TOP	(LOONGSON_PCILO0_BASE+LOONGSON_PCILO_SIZE-1)
+
+#define LOONGSON_PCICFG_BASE	0x1fe80000
+#define LOONGSON_PCICFG_SIZE	0x00000800	/* 2K */
+#define LOONGSON_PCICFG_TOP	(LOONGSON_PCICFG_BASE+LOONGSON_PCICFG_SIZE-1)
+
+#define LOONGSON_PCIIO_BASE	loongson_sysconf.pci_io_base
+
+#define LOONGSON_PCIIO_SIZE	0x00100000	/* 1M */
+#define LOONGSON_PCIIO_TOP	(LOONGSON_PCIIO_BASE+LOONGSON_PCIIO_SIZE-1)
+
+/* Loongson Register Bases */
+
+#define LOONGSON_PCICONFIGBASE	0x00
+#define LOONGSON_REGBASE	0x100
+
+/* PCI Configuration Registers */
+
+#define LOONGSON_PCI_REG(x)	LOONGSON_REG(LOONGSON_PCICONFIGBASE + (x))
+#define LOONGSON_PCIDID		LOONGSON_PCI_REG(0x00)
+#define LOONGSON_PCICMD		LOONGSON_PCI_REG(0x04)
+#define LOONGSON_PCICLASS	LOONGSON_PCI_REG(0x08)
+#define LOONGSON_PCILTIMER	LOONGSON_PCI_REG(0x0c)
+#define LOONGSON_PCIBASE0	LOONGSON_PCI_REG(0x10)
+#define LOONGSON_PCIBASE1	LOONGSON_PCI_REG(0x14)
+#define LOONGSON_PCIBASE2	LOONGSON_PCI_REG(0x18)
+#define LOONGSON_PCIBASE3	LOONGSON_PCI_REG(0x1c)
+#define LOONGSON_PCIBASE4	LOONGSON_PCI_REG(0x20)
+#define LOONGSON_PCIEXPRBASE	LOONGSON_PCI_REG(0x30)
+#define LOONGSON_PCIINT		LOONGSON_PCI_REG(0x3c)
+
+#define LOONGSON_PCI_ISR4C	LOONGSON_PCI_REG(0x4c)
+
+#define LOONGSON_PCICMD_PERR_CLR	0x80000000
+#define LOONGSON_PCICMD_SERR_CLR	0x40000000
+#define LOONGSON_PCICMD_MABORT_CLR	0x20000000
+#define LOONGSON_PCICMD_MTABORT_CLR	0x10000000
+#define LOONGSON_PCICMD_TABORT_CLR	0x08000000
+#define LOONGSON_PCICMD_MPERR_CLR	0x01000000
+#define LOONGSON_PCICMD_PERRRESPEN	0x00000040
+#define LOONGSON_PCICMD_ASTEPEN		0x00000080
+#define LOONGSON_PCICMD_SERREN		0x00000100
+#define LOONGSON_PCILTIMER_BUSLATENCY	0x0000ff00
+#define LOONGSON_PCILTIMER_BUSLATENCY_SHIFT	8
+
+/* Loongson h/w Configuration */
+
+#define LOONGSON_GENCFG_OFFSET		0x4
+#define LOONGSON_GENCFG LOONGSON_REG(LOONGSON_REGBASE + LOONGSON_GENCFG_OFFSET)
+
+#define LOONGSON_GENCFG_DEBUGMODE	0x00000001
+#define LOONGSON_GENCFG_SNOOPEN		0x00000002
+#define LOONGSON_GENCFG_CPUSELFRESET	0x00000004
+
+#define LOONGSON_GENCFG_FORCE_IRQA	0x00000008
+#define LOONGSON_GENCFG_IRQA_ISOUT	0x00000010
+#define LOONGSON_GENCFG_IRQA_FROM_INT1	0x00000020
+#define LOONGSON_GENCFG_BYTESWAP	0x00000040
+
+#define LOONGSON_GENCFG_UNCACHED	0x00000080
+#define LOONGSON_GENCFG_PREFETCHEN	0x00000100
+#define LOONGSON_GENCFG_WBEHINDEN	0x00000200
+#define LOONGSON_GENCFG_CACHEALG	0x00000c00
+#define LOONGSON_GENCFG_CACHEALG_SHIFT	10
+#define LOONGSON_GENCFG_PCIQUEUE	0x00001000
+#define LOONGSON_GENCFG_CACHESTOP	0x00002000
+#define LOONGSON_GENCFG_MSTRBYTESWAP	0x00004000
+#define LOONGSON_GENCFG_BUSERREN	0x00008000
+#define LOONGSON_GENCFG_NORETRYTIMEOUT	0x00010000
+#define LOONGSON_GENCFG_SHORTCOPYTIMEOUT	0x00020000
+
+/* PCI address map control */
+
+#define LOONGSON_PCIMAP			LOONGSON_REG(LOONGSON_REGBASE + 0x10)
+#define LOONGSON_PCIMEMBASECFG		LOONGSON_REG(LOONGSON_REGBASE + 0x14)
+#define LOONGSON_PCIMAP_CFG		LOONGSON_REG(LOONGSON_REGBASE + 0x18)
+
+/* GPIO Regs - r/w */
+
+#define LOONGSON_GPIODATA		LOONGSON_REG(LOONGSON_REGBASE + 0x1c)
+#define LOONGSON_GPIOIE			LOONGSON_REG(LOONGSON_REGBASE + 0x20)
+
+/* ICU Configuration Regs - r/w */
+
+#define LOONGSON_INTEDGE		LOONGSON_REG(LOONGSON_REGBASE + 0x24)
+#define LOONGSON_INTSTEER		LOONGSON_REG(LOONGSON_REGBASE + 0x28)
+#define LOONGSON_INTPOL			LOONGSON_REG(LOONGSON_REGBASE + 0x2c)
+
+/* ICU Enable Regs - IntEn & IntISR are r/o. */
+
+#define LOONGSON_INTENSET		LOONGSON_REG(LOONGSON_REGBASE + 0x30)
+#define LOONGSON_INTENCLR		LOONGSON_REG(LOONGSON_REGBASE + 0x34)
+#define LOONGSON_INTEN			LOONGSON_REG(LOONGSON_REGBASE + 0x38)
+#define LOONGSON_INTISR			LOONGSON_REG(LOONGSON_REGBASE + 0x3c)
+
+/* ICU */
+#define LOONGSON_ICU_MBOXES		0x0000000f
+#define LOONGSON_ICU_MBOXES_SHIFT	0
+#define LOONGSON_ICU_DMARDY		0x00000010
+#define LOONGSON_ICU_DMAEMPTY		0x00000020
+#define LOONGSON_ICU_COPYRDY		0x00000040
+#define LOONGSON_ICU_COPYEMPTY		0x00000080
+#define LOONGSON_ICU_COPYERR		0x00000100
+#define LOONGSON_ICU_PCIIRQ		0x00000200
+#define LOONGSON_ICU_MASTERERR		0x00000400
+#define LOONGSON_ICU_SYSTEMERR		0x00000800
+#define LOONGSON_ICU_DRAMPERR		0x00001000
+#define LOONGSON_ICU_RETRYERR		0x00002000
+#define LOONGSON_ICU_GPIOS		0x01ff0000
+#define LOONGSON_ICU_GPIOS_SHIFT		16
+#define LOONGSON_ICU_GPINS		0x7e000000
+#define LOONGSON_ICU_GPINS_SHIFT		25
+#define LOONGSON_ICU_MBOX(N)		(1<<(LOONGSON_ICU_MBOXES_SHIFT+(N)))
+#define LOONGSON_ICU_GPIO(N)		(1<<(LOONGSON_ICU_GPIOS_SHIFT+(N)))
+#define LOONGSON_ICU_GPIN(N)		(1<<(LOONGSON_ICU_GPINS_SHIFT+(N)))
+
+/* PCI prefetch window base & mask */
+
+#define LOONGSON_MEM_WIN_BASE_L		LOONGSON_REG(LOONGSON_REGBASE + 0x40)
+#define LOONGSON_MEM_WIN_BASE_H		LOONGSON_REG(LOONGSON_REGBASE + 0x44)
+#define LOONGSON_MEM_WIN_MASK_L		LOONGSON_REG(LOONGSON_REGBASE + 0x48)
+#define LOONGSON_MEM_WIN_MASK_H		LOONGSON_REG(LOONGSON_REGBASE + 0x4c)
+
+/* PCI_Hit*_Sel_* */
+
+#define LOONGSON_PCI_HIT0_SEL_L		LOONGSON_REG(LOONGSON_REGBASE + 0x50)
+#define LOONGSON_PCI_HIT0_SEL_H		LOONGSON_REG(LOONGSON_REGBASE + 0x54)
+#define LOONGSON_PCI_HIT1_SEL_L		LOONGSON_REG(LOONGSON_REGBASE + 0x58)
+#define LOONGSON_PCI_HIT1_SEL_H		LOONGSON_REG(LOONGSON_REGBASE + 0x5c)
+#define LOONGSON_PCI_HIT2_SEL_L		LOONGSON_REG(LOONGSON_REGBASE + 0x60)
+#define LOONGSON_PCI_HIT2_SEL_H		LOONGSON_REG(LOONGSON_REGBASE + 0x64)
+
+/* PXArb Config & Status */
+
+#define LOONGSON_PXARB_CFG		LOONGSON_REG(LOONGSON_REGBASE + 0x68)
+#define LOONGSON_PXARB_STATUS		LOONGSON_REG(LOONGSON_REGBASE + 0x6c)
+
+#define MAX_PACKAGES 4
+
+/* Chip Config registor of each physical cpu package, PRid >= Loongson-2F */
+extern u64 loongson_chipcfg[MAX_PACKAGES];
+#define LOONGSON_CHIPCFG(id) (*(volatile u32 *)(loongson_chipcfg[id]))
+
+/* Chip Temperature registor of each physical cpu package, PRid >= Loongson-3A */
+extern u64 loongson_chiptemp[MAX_PACKAGES];
+#define LOONGSON_CHIPTEMP(id) (*(volatile u32 *)(loongson_chiptemp[id]))
+
+/* Freq Control register of each physical cpu package, PRid >= Loongson-3B */
+extern u64 loongson_freqctrl[MAX_PACKAGES];
+#define LOONGSON_FREQCTRL(id) (*(volatile u32 *)(loongson_freqctrl[id]))
+
+/* pcimap */
+
+#define LOONGSON_PCIMAP_PCIMAP_LO0	0x0000003f
+#define LOONGSON_PCIMAP_PCIMAP_LO0_SHIFT	0
+#define LOONGSON_PCIMAP_PCIMAP_LO1	0x00000fc0
+#define LOONGSON_PCIMAP_PCIMAP_LO1_SHIFT	6
+#define LOONGSON_PCIMAP_PCIMAP_LO2	0x0003f000
+#define LOONGSON_PCIMAP_PCIMAP_LO2_SHIFT	12
+#define LOONGSON_PCIMAP_PCIMAP_2	0x00040000
+#define LOONGSON_PCIMAP_WIN(WIN, ADDR)	\
+	((((ADDR)>>26) & LOONGSON_PCIMAP_PCIMAP_LO0) << ((WIN)*6))
+
+#endif /* __ASM_MACH_LOONGSON64_LOONGSON_H */
diff --git a/arch/mips/include/asm/mach-loongson64/loongson_hwmon.h b/arch/mips/include/asm/mach-loongson64/loongson_hwmon.h
new file mode 100644
index 000000000..545f91f2a
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson64/loongson_hwmon.h
@@ -0,0 +1,56 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __LOONGSON_HWMON_H_
+#define __LOONGSON_HWMON_H_
+
+#include <linux/types.h>
+
+#define MIN_TEMP	0
+#define MAX_TEMP	255
+#define NOT_VALID_TEMP	999
+
+typedef int (*get_temp_fun)(int);
+extern int loongson3_cpu_temp(int);
+
+/* 0:Max speed, 1:Manual, 2:Auto */
+enum fan_control_mode {
+	FAN_FULL_MODE = 0,
+	FAN_MANUAL_MODE = 1,
+	FAN_AUTO_MODE = 2,
+	FAN_MODE_END
+};
+
+struct temp_range {
+	u8 low;
+	u8 high;
+	u8 level;
+};
+
+#define CONSTANT_SPEED_POLICY	0  /* at constant speed */
+#define STEP_SPEED_POLICY	1  /* use up/down arrays to describe policy */
+#define KERNEL_HELPER_POLICY	2  /* kernel as a helper to fan control */
+
+#define MAX_STEP_NUM	16
+#define MAX_FAN_LEVEL	255
+
+/* loongson_fan_policy works when fan work at FAN_AUTO_MODE */
+struct loongson_fan_policy {
+	u8	type;
+
+	/* percent only used when type is CONSTANT_SPEED_POLICY */
+	u8	percent;
+
+	/* period between two check. (Unit: S) */
+	u8	adjust_period;
+
+	/* fan adjust usually depend on a temprature input */
+	get_temp_fun	depend_temp;
+
+	/* up_step/down_step used when type is STEP_SPEED_POLICY */
+	u8	up_step_num;
+	u8	down_step_num;
+	struct temp_range up_step[MAX_STEP_NUM];
+	struct temp_range down_step[MAX_STEP_NUM];
+	struct delayed_work work;
+};
+
+#endif /* __LOONGSON_HWMON_H_*/
diff --git a/arch/mips/include/asm/mach-loongson64/loongson_regs.h b/arch/mips/include/asm/mach-loongson64/loongson_regs.h
new file mode 100644
index 000000000..b5be7511f
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson64/loongson_regs.h
@@ -0,0 +1,268 @@
+/*
+ * Read/Write Loongson Extension Registers
+ */
+
+#ifndef _LOONGSON_REGS_H_
+#define _LOONGSON_REGS_H_
+
+#include <linux/types.h>
+#include <linux/bits.h>
+
+#include <asm/mipsregs.h>
+#include <asm/cpu.h>
+
+static inline bool cpu_has_cfg(void)
+{
+	return ((read_c0_prid() & PRID_IMP_MASK) == PRID_IMP_LOONGSON_64G);
+}
+
+static inline u32 read_cpucfg(u32 reg)
+{
+	u32 __res;
+
+	__asm__ __volatile__(
+		_ASM_SET_PARSE_R
+		"parse_r __res,%0\n\t"
+		"parse_r reg,%1\n\t"
+		_ASM_UNSET_PARSE_R
+		".insn \n\t"
+		".word (0xc8080118 | (reg << 21) | (__res << 11))\n\t"
+		:"=r"(__res)
+		:"r"(reg)
+		:
+		);
+	return __res;
+}
+
+/* Bit Domains for CFG registers */
+#define LOONGSON_CFG0	0x0
+#define LOONGSON_CFG0_PRID GENMASK(31, 0)
+
+#define LOONGSON_CFG1 0x1
+#define LOONGSON_CFG1_FP	BIT(0)
+#define LOONGSON_CFG1_FPREV	GENMASK(3, 1)
+#define LOONGSON_CFG1_MMI	BIT(4)
+#define LOONGSON_CFG1_MSA1	BIT(5)
+#define LOONGSON_CFG1_MSA2	BIT(6)
+#define LOONGSON_CFG1_CGP	BIT(7)
+#define LOONGSON_CFG1_WRP	BIT(8)
+#define LOONGSON_CFG1_LSX1	BIT(9)
+#define LOONGSON_CFG1_LSX2	BIT(10)
+#define LOONGSON_CFG1_LASX	BIT(11)
+#define LOONGSON_CFG1_R6FXP	BIT(12)
+#define LOONGSON_CFG1_R6CRCP	BIT(13)
+#define LOONGSON_CFG1_R6FPP	BIT(14)
+#define LOONGSON_CFG1_CNT64	BIT(15)
+#define LOONGSON_CFG1_LSLDR0	BIT(16)
+#define LOONGSON_CFG1_LSPREF	BIT(17)
+#define LOONGSON_CFG1_LSPREFX	BIT(18)
+#define LOONGSON_CFG1_LSSYNCI	BIT(19)
+#define LOONGSON_CFG1_LSUCA	BIT(20)
+#define LOONGSON_CFG1_LLSYNC	BIT(21)
+#define LOONGSON_CFG1_TGTSYNC	BIT(22)
+#define LOONGSON_CFG1_LLEXC	BIT(23)
+#define LOONGSON_CFG1_SCRAND	BIT(24)
+#define LOONGSON_CFG1_MUALP	BIT(25)
+#define LOONGSON_CFG1_KMUALEN	BIT(26)
+#define LOONGSON_CFG1_ITLBT	BIT(27)
+#define LOONGSON_CFG1_LSUPERF	BIT(28)
+#define LOONGSON_CFG1_SFBP	BIT(29)
+#define LOONGSON_CFG1_CDMAP	BIT(30)
+
+#define LOONGSON_CFG1_FPREV_OFFSET	1
+
+#define LOONGSON_CFG2 0x2
+#define LOONGSON_CFG2_LEXT1	BIT(0)
+#define LOONGSON_CFG2_LEXT2	BIT(1)
+#define LOONGSON_CFG2_LEXT3	BIT(2)
+#define LOONGSON_CFG2_LSPW	BIT(3)
+#define LOONGSON_CFG2_LBT1	BIT(4)
+#define LOONGSON_CFG2_LBT2	BIT(5)
+#define LOONGSON_CFG2_LBT3	BIT(6)
+#define LOONGSON_CFG2_LBTMMU	BIT(7)
+#define LOONGSON_CFG2_LPMP	BIT(8)
+#define LOONGSON_CFG2_LPMREV	GENMASK(11, 9)
+#define LOONGSON_CFG2_LAMO	BIT(12)
+#define LOONGSON_CFG2_LPIXU	BIT(13)
+#define LOONGSON_CFG2_LPIXNU	BIT(14)
+#define LOONGSON_CFG2_LVZP	BIT(15)
+#define LOONGSON_CFG2_LVZREV	GENMASK(18, 16)
+#define LOONGSON_CFG2_LGFTP	BIT(19)
+#define LOONGSON_CFG2_LGFTPREV	GENMASK(22, 20)
+#define LOONGSON_CFG2_LLFTP	BIT(23)
+#define LOONGSON_CFG2_LLFTPREV	GENMASK(26, 24)
+#define LOONGSON_CFG2_LCSRP	BIT(27)
+#define LOONGSON_CFG2_LDISBLIKELY	BIT(28)
+
+#define LOONGSON_CFG2_LPMREV_OFFSET	9
+#define LOONGSON_CFG2_LPM_REV1		(1 << LOONGSON_CFG2_LPMREV_OFFSET)
+#define LOONGSON_CFG2_LPM_REV2		(2 << LOONGSON_CFG2_LPMREV_OFFSET)
+#define LOONGSON_CFG2_LVZREV_OFFSET	16
+#define LOONGSON_CFG2_LVZ_REV1		(1 << LOONGSON_CFG2_LVZREV_OFFSET)
+#define LOONGSON_CFG2_LVZ_REV2		(2 << LOONGSON_CFG2_LVZREV_OFFSET)
+
+#define LOONGSON_CFG3 0x3
+#define LOONGSON_CFG3_LCAMP	BIT(0)
+#define LOONGSON_CFG3_LCAMREV	GENMASK(3, 1)
+#define LOONGSON_CFG3_LCAMNUM	GENMASK(11, 4)
+#define LOONGSON_CFG3_LCAMKW	GENMASK(19, 12)
+#define LOONGSON_CFG3_LCAMVW	GENMASK(27, 20)
+
+#define LOONGSON_CFG3_LCAMREV_OFFSET	1
+#define LOONGSON_CFG3_LCAM_REV1		(1 << LOONGSON_CFG3_LCAMREV_OFFSET)
+#define LOONGSON_CFG3_LCAM_REV2		(2 << LOONGSON_CFG3_LCAMREV_OFFSET)
+#define LOONGSON_CFG3_LCAMNUM_OFFSET	4
+#define LOONGSON_CFG3_LCAMNUM_REV1	(0x3f << LOONGSON_CFG3_LCAMNUM_OFFSET)
+#define LOONGSON_CFG3_LCAMKW_OFFSET	12
+#define LOONGSON_CFG3_LCAMKW_REV1	(0x27 << LOONGSON_CFG3_LCAMKW_OFFSET)
+#define LOONGSON_CFG3_LCAMVW_OFFSET	20
+#define LOONGSON_CFG3_LCAMVW_REV1	(0x3f << LOONGSON_CFG3_LCAMVW_OFFSET)
+
+#define LOONGSON_CFG4 0x4
+#define LOONGSON_CFG4_CCFREQ	GENMASK(31, 0)
+
+#define LOONGSON_CFG5 0x5
+#define LOONGSON_CFG5_CFM	GENMASK(15, 0)
+#define LOONGSON_CFG5_CFD	GENMASK(31, 16)
+
+#define LOONGSON_CFG6 0x6
+
+#define LOONGSON_CFG7 0x7
+#define LOONGSON_CFG7_GCCAEQRP	BIT(0)
+#define LOONGSON_CFG7_UCAWINP	BIT(1)
+
+static inline bool cpu_has_csr(void)
+{
+	if (cpu_has_cfg())
+		return (read_cpucfg(LOONGSON_CFG2) & LOONGSON_CFG2_LCSRP);
+
+	return false;
+}
+
+static inline u32 csr_readl(u32 reg)
+{
+	u32 __res;
+
+	/* RDCSR reg, val */
+	__asm__ __volatile__(
+		_ASM_SET_PARSE_R
+		"parse_r __res,%0\n\t"
+		"parse_r reg,%1\n\t"
+		_ASM_UNSET_PARSE_R
+		".insn \n\t"
+		".word (0xc8000118 | (reg << 21) | (__res << 11))\n\t"
+		:"=r"(__res)
+		:"r"(reg)
+		:
+		);
+	return __res;
+}
+
+static inline u64 csr_readq(u32 reg)
+{
+	u64 __res;
+
+	/* DRDCSR reg, val */
+	__asm__ __volatile__(
+		_ASM_SET_PARSE_R
+		"parse_r __res,%0\n\t"
+		"parse_r reg,%1\n\t"
+		_ASM_UNSET_PARSE_R
+		".insn \n\t"
+		".word (0xc8020118 | (reg << 21) | (__res << 11))\n\t"
+		:"=r"(__res)
+		:"r"(reg)
+		:
+		);
+	return __res;
+}
+
+static inline void csr_writel(u32 val, u32 reg)
+{
+	/* WRCSR reg, val */
+	__asm__ __volatile__(
+		_ASM_SET_PARSE_R
+		"parse_r reg,%0\n\t"
+		"parse_r val,%1\n\t"
+		_ASM_UNSET_PARSE_R
+		".insn \n\t"
+		".word (0xc8010118 | (reg << 21) | (val << 11))\n\t"
+		:
+		:"r"(reg),"r"(val)
+		:
+		);
+}
+
+static inline void csr_writeq(u64 val, u32 reg)
+{
+	/* DWRCSR reg, val */
+	__asm__ __volatile__(
+		_ASM_SET_PARSE_R
+		"parse_r reg,%0\n\t"
+		"parse_r val,%1\n\t"
+		_ASM_UNSET_PARSE_R
+		".insn \n\t"
+		".word (0xc8030118 | (reg << 21) | (val << 11))\n\t"
+		:
+		:"r"(reg),"r"(val)
+		:
+		);
+}
+
+/* Public CSR Register can also be accessed with regular addresses */
+#define CSR_PUBLIC_MMIO_BASE 0x1fe00000
+
+#define MMIO_CSR(x)		(void *)TO_UNCAC(CSR_PUBLIC_MMIO_BASE + x)
+
+#define LOONGSON_CSR_FEATURES	0x8
+#define LOONGSON_CSRF_TEMP	BIT(0)
+#define LOONGSON_CSRF_NODECNT	BIT(1)
+#define LOONGSON_CSRF_MSI	BIT(2)
+#define LOONGSON_CSRF_EXTIOI	BIT(3)
+#define LOONGSON_CSRF_IPI	BIT(4)
+#define LOONGSON_CSRF_FREQ	BIT(5)
+
+#define LOONGSON_CSR_VENDOR	0x10 /* Vendor name string, should be "Loongson" */
+#define LOONGSON_CSR_CPUNAME	0x20 /* Processor name string */
+#define LOONGSON_CSR_NODECNT	0x408
+#define LOONGSON_CSR_CPUTEMP	0x428
+
+/* PerCore CSR, only accessable by local cores */
+#define LOONGSON_CSR_IPI_STATUS	0x1000
+#define LOONGSON_CSR_IPI_EN	0x1004
+#define LOONGSON_CSR_IPI_SET	0x1008
+#define LOONGSON_CSR_IPI_CLEAR	0x100c
+#define LOONGSON_CSR_IPI_SEND	0x1040
+#define CSR_IPI_SEND_IP_SHIFT	0
+#define CSR_IPI_SEND_CPU_SHIFT	16
+#define CSR_IPI_SEND_BLOCK	BIT(31)
+
+#define LOONGSON_CSR_MAIL_BUF0		0x1020
+#define LOONGSON_CSR_MAIL_SEND		0x1048
+#define CSR_MAIL_SEND_BLOCK		BIT_ULL(31)
+#define CSR_MAIL_SEND_BOX_LOW(box)	(box << 1)
+#define CSR_MAIL_SEND_BOX_HIGH(box)	((box << 1) + 1)
+#define CSR_MAIL_SEND_BOX_SHIFT		2
+#define CSR_MAIL_SEND_CPU_SHIFT		16
+#define CSR_MAIL_SEND_BUF_SHIFT		32
+#define CSR_MAIL_SEND_H32_MASK		0xFFFFFFFF00000000ULL
+
+static inline u64 drdtime(void)
+{
+	int rID = 0;
+	u64 val = 0;
+
+	__asm__ __volatile__(
+		_ASM_SET_PARSE_R
+		"parse_r rID,%0\n\t"
+		"parse_r val,%1\n\t"
+		_ASM_UNSET_PARSE_R
+		".insn \n\t"
+		".word (0xc8090118 | (rID << 21) | (val << 11))\n\t"
+		:"=r"(rID),"=r"(val)
+		:
+		);
+	return val;
+}
+
+#endif
diff --git a/arch/mips/include/asm/mach-loongson64/mmzone.h b/arch/mips/include/asm/mach-loongson64/mmzone.h
new file mode 100644
index 000000000..ebb1deaa7
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson64/mmzone.h
@@ -0,0 +1,24 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2010 Loongson Inc. & Lemote Inc. &
+ *                    Institute of Computing Technology
+ * Author:  Xiang Gao, gaoxiang@ict.ac.cn
+ *          Huacai Chen, chenhc@lemote.com
+ *          Xiaofu Meng, Shuangshuang Zhang
+ */
+#ifndef _ASM_MACH_LOONGSON64_MMZONE_H
+#define _ASM_MACH_LOONGSON64_MMZONE_H
+
+#define NODE_ADDRSPACE_SHIFT 44
+
+#define pa_to_nid(addr)  (((addr) & 0xf00000000000) >> NODE_ADDRSPACE_SHIFT)
+#define nid_to_addrbase(nid) ((unsigned long)(nid) << NODE_ADDRSPACE_SHIFT)
+
+extern struct pglist_data *__node_data[];
+
+#define NODE_DATA(n)		(__node_data[n])
+
+extern void setup_zero_pages(void);
+extern void __init prom_init_numa_memory(void);
+
+#endif /* _ASM_MACH_MMZONE_H */
diff --git a/arch/mips/include/asm/mach-loongson64/pci.h b/arch/mips/include/asm/mach-loongson64/pci.h
new file mode 100644
index 000000000..8b59d64a2
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson64/pci.h
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (c) 2008 Zhang Le <r0bertz@gentoo.org>
+ * Copyright (c) 2009 Wu Zhangjin <wuzhangjin@gmail.com>
+ */
+
+#ifndef __ASM_MACH_LOONGSON64_PCI_H_
+#define __ASM_MACH_LOONGSON64_PCI_H_
+
+extern struct pci_ops loongson_pci_ops;
+
+/* this is an offset from mips_io_port_base */
+#define LOONGSON_PCI_IO_START	0x00004000UL
+
+#define LOONGSON_PCI_MEM_START	0x40000000UL
+#define LOONGSON_PCI_MEM_END	0x7effffffUL
+
+
+#endif /* !__ASM_MACH_LOONGSON64_PCI_H_ */
diff --git a/arch/mips/include/asm/mach-loongson64/spaces.h b/arch/mips/include/asm/mach-loongson64/spaces.h
new file mode 100644
index 000000000..ce04e998a
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson64/spaces.h
@@ -0,0 +1,17 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_MACH_LOONGSON64_SPACES_H_
+#define __ASM_MACH_LOONGSON64_SPACES_H_
+
+#if defined(CONFIG_64BIT)
+#define CAC_BASE        _AC(0x9800000000000000, UL)
+#endif /* CONFIG_64BIT */
+
+/* Skip 128k to trap NULL pointer dereferences */
+#define PCI_IOBASE	_AC(0xc000000000000000 + SZ_128K, UL)
+#define PCI_IOSIZE	SZ_16M
+#define MAP_BASE	(PCI_IOBASE + PCI_IOSIZE)
+
+#define IO_SPACE_LIMIT  (PCI_IOSIZE - 1)
+
+#include <asm/mach-generic/spaces.h>
+#endif
diff --git a/arch/mips/include/asm/mach-loongson64/topology.h b/arch/mips/include/asm/mach-loongson64/topology.h
new file mode 100644
index 000000000..3414a1fd1
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson64/topology.h
@@ -0,0 +1,25 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _ASM_MACH_TOPOLOGY_H
+#define _ASM_MACH_TOPOLOGY_H
+
+#ifdef CONFIG_NUMA
+
+#define cpu_to_node(cpu)	(cpu_logical_map(cpu) >> 2)
+
+extern cpumask_t __node_cpumask[];
+#define cpumask_of_node(node)	(&__node_cpumask[node])
+
+struct pci_bus;
+extern int pcibus_to_node(struct pci_bus *);
+
+#define cpumask_of_pcibus(bus)	(cpu_online_mask)
+
+extern unsigned char __node_distances[MAX_NUMNODES][MAX_NUMNODES];
+
+#define node_distance(from, to)	(__node_distances[(from)][(to)])
+
+#endif
+
+#include <asm-generic/topology.h>
+
+#endif /* _ASM_MACH_TOPOLOGY_H */
diff --git a/arch/mips/include/asm/mach-loongson64/workarounds.h b/arch/mips/include/asm/mach-loongson64/workarounds.h
new file mode 100644
index 000000000..17b71172a
--- /dev/null
+++ b/arch/mips/include/asm/mach-loongson64/workarounds.h
@@ -0,0 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_MACH_LOONGSON64_WORKAROUNDS_H_
+#define __ASM_MACH_LOONGSON64_WORKAROUNDS_H_
+
+#define WORKAROUND_CPUFREQ	0x00000001
+#define WORKAROUND_CPUHOTPLUG	0x00000002
+
+#endif
diff --git a/arch/mips/include/asm/mach-malta/cpu-feature-overrides.h b/arch/mips/include/asm/mach-malta/cpu-feature-overrides.h
new file mode 100644
index 000000000..de3b66a37
--- /dev/null
+++ b/arch/mips/include/asm/mach-malta/cpu-feature-overrides.h
@@ -0,0 +1,70 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003, 2004 Chris Dearman
+ * Copyright (C) 2005 Ralf Baechle (ralf@linux-mips.org)
+ */
+#ifndef __ASM_MACH_MIPS_CPU_FEATURE_OVERRIDES_H
+#define __ASM_MACH_MIPS_CPU_FEATURE_OVERRIDES_H
+
+
+/*
+ * CPU feature overrides for MIPS boards
+ */
+#ifdef CONFIG_CPU_MIPS32
+#define cpu_has_tlb		1
+#define cpu_has_4kex		1
+#define cpu_has_4k_cache	1
+/* #define cpu_has_fpu		? */
+/* #define cpu_has_32fpr	? */
+#define cpu_has_counter		1
+/* #define cpu_has_watch	? */
+#define cpu_has_divec		1
+#define cpu_has_vce		0
+/* #define cpu_has_cache_cdex_p ? */
+/* #define cpu_has_cache_cdex_s ? */
+/* #define cpu_has_prefetch	? */
+#define cpu_has_mcheck		1
+/* #define cpu_has_ejtag	? */
+#define cpu_has_llsc		1
+/* #define cpu_has_vtag_icache	? */
+/* #define cpu_has_dc_aliases	? */
+/* #define cpu_has_ic_fills_f_dc ? */
+#define cpu_has_clo_clz		1
+#define cpu_has_nofpuex		0
+/* #define cpu_has_64bits	? */
+/* #define cpu_has_64bit_zero_reg ? */
+/* #define cpu_has_inclusive_pcaches ? */
+#define cpu_icache_snoops_remote_store 1
+#endif
+
+#ifdef CONFIG_CPU_MIPS64
+#define cpu_has_tlb		1
+#define cpu_has_4kex		1
+#define cpu_has_4k_cache	1
+/* #define cpu_has_fpu		? */
+/* #define cpu_has_32fpr	? */
+#define cpu_has_counter		1
+/* #define cpu_has_watch	? */
+#define cpu_has_divec		1
+#define cpu_has_vce		0
+/* #define cpu_has_cache_cdex_p ? */
+/* #define cpu_has_cache_cdex_s ? */
+/* #define cpu_has_prefetch	? */
+#define cpu_has_mcheck		1
+/* #define cpu_has_ejtag	? */
+#define cpu_has_llsc		1
+/* #define cpu_has_vtag_icache	? */
+/* #define cpu_has_dc_aliases	? */
+/* #define cpu_has_ic_fills_f_dc ? */
+#define cpu_has_clo_clz		1
+#define cpu_has_nofpuex		0
+/* #define cpu_has_64bits	? */
+/* #define cpu_has_64bit_zero_reg ? */
+/* #define cpu_has_inclusive_pcaches ? */
+#define cpu_icache_snoops_remote_store 1
+#endif
+
+#endif /* __ASM_MACH_MIPS_CPU_FEATURE_OVERRIDES_H */
diff --git a/arch/mips/include/asm/mach-malta/irq.h b/arch/mips/include/asm/mach-malta/irq.h
new file mode 100644
index 000000000..e1bd4298b
--- /dev/null
+++ b/arch/mips/include/asm/mach-malta/irq.h
@@ -0,0 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_MACH_MIPS_IRQ_H
+#define __ASM_MACH_MIPS_IRQ_H
+
+
+#define NR_IRQS 256
+
+#include <asm/mach-generic/irq.h>
+
+#endif /* __ASM_MACH_MIPS_IRQ_H */
diff --git a/arch/mips/include/asm/mach-malta/kernel-entry-init.h b/arch/mips/include/asm/mach-malta/kernel-entry-init.h
new file mode 100644
index 000000000..ab03eb3fa
--- /dev/null
+++ b/arch/mips/include/asm/mach-malta/kernel-entry-init.h
@@ -0,0 +1,145 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Chris Dearman (chris@mips.com)
+ * Copyright (C) 2007 Mips Technologies, Inc.
+ * Copyright (C) 2014 Imagination Technologies Ltd.
+ */
+#ifndef __ASM_MACH_MIPS_KERNEL_ENTRY_INIT_H
+#define __ASM_MACH_MIPS_KERNEL_ENTRY_INIT_H
+
+#include <asm/regdef.h>
+#include <asm/mipsregs.h>
+
+	/*
+	 * Prepare segments for EVA boot:
+	 *
+	 * This is in case the processor boots in legacy configuration
+	 * (SI_EVAReset is de-asserted and CONFIG5.K == 0)
+	 *
+	 * ========================= Mappings =============================
+	 * Virtual memory           Physical memory           Mapping
+	 * 0x00000000 - 0x7fffffff  0x80000000 - 0xfffffffff   MUSUK (kuseg)
+	 *                          Flat 2GB physical memory
+	 *
+	 * 0x80000000 - 0x9fffffff  0x00000000 - 0x1ffffffff   MUSUK (kseg0)
+	 * 0xa0000000 - 0xbf000000  0x00000000 - 0x1ffffffff   MUSUK (kseg1)
+	 * 0xc0000000 - 0xdfffffff             -                 MK  (kseg2)
+	 * 0xe0000000 - 0xffffffff             -                 MK  (kseg3)
+	 *
+	 *
+	 * Lowmem is expanded to 2GB
+	 *
+	 * The following code uses the t0, t1, t2 and ra registers without
+	 * previously preserving them.
+	 *
+	 */
+	.macro	platform_eva_init
+
+	.set	push
+	.set	reorder
+	/*
+	 * Get Config.K0 value and use it to program
+	 * the segmentation registers
+	 */
+	mfc0    t1, CP0_CONFIG
+	andi	t1, 0x7 /* CCA */
+	move	t2, t1
+	ins	t2, t1, 16, 3
+	/* SegCtl0 */
+	li      t0, ((MIPS_SEGCFG_MK << MIPS_SEGCFG_AM_SHIFT) |		\
+		(0 << MIPS_SEGCFG_PA_SHIFT) |				\
+		(1 << MIPS_SEGCFG_EU_SHIFT)) |				\
+		(((MIPS_SEGCFG_MK << MIPS_SEGCFG_AM_SHIFT) |		\
+		(0 << MIPS_SEGCFG_PA_SHIFT) |				\
+		(1 << MIPS_SEGCFG_EU_SHIFT)) << 16)
+	or	t0, t2
+	mtc0	t0, CP0_SEGCTL0
+
+	/* SegCtl1 */
+	li      t0, ((MIPS_SEGCFG_MUSUK << MIPS_SEGCFG_AM_SHIFT) |	\
+		(0 << MIPS_SEGCFG_PA_SHIFT) |				\
+		(2 << MIPS_SEGCFG_C_SHIFT) |				\
+		(1 << MIPS_SEGCFG_EU_SHIFT)) |				\
+		(((MIPS_SEGCFG_MUSUK << MIPS_SEGCFG_AM_SHIFT) |		\
+		(0 << MIPS_SEGCFG_PA_SHIFT) |				\
+		(1 << MIPS_SEGCFG_EU_SHIFT)) << 16)
+	ins	t0, t1, 16, 3
+	mtc0	t0, CP0_SEGCTL1
+
+	/* SegCtl2 */
+	li	t0, ((MIPS_SEGCFG_MUSUK << MIPS_SEGCFG_AM_SHIFT) |	\
+		(6 << MIPS_SEGCFG_PA_SHIFT) |				\
+		(1 << MIPS_SEGCFG_EU_SHIFT)) |				\
+		(((MIPS_SEGCFG_MUSUK << MIPS_SEGCFG_AM_SHIFT) |		\
+		(4 << MIPS_SEGCFG_PA_SHIFT) |				\
+		(1 << MIPS_SEGCFG_EU_SHIFT)) << 16)
+	or	t0, t2
+	mtc0	t0, CP0_SEGCTL2
+
+	jal	mips_ihb
+	mfc0    t0, $16, 5
+	li      t2, 0x40000000      /* K bit */
+	or      t0, t0, t2
+	mtc0    t0, $16, 5
+	sync
+	jal	mips_ihb
+
+	.set	pop
+	.endm
+
+	.macro	kernel_entry_setup
+
+#ifdef CONFIG_EVA
+	sync
+	ehb
+
+	mfc0    t1, CP0_CONFIG
+	bgez    t1, 9f
+	mfc0	t0, CP0_CONFIG, 1
+	bgez	t0, 9f
+	mfc0	t0, CP0_CONFIG, 2
+	bgez	t0, 9f
+	mfc0	t0, CP0_CONFIG, 3
+	sll     t0, t0, 6   /* SC bit */
+	bgez    t0, 9f
+
+	platform_eva_init
+	b       0f
+9:
+	/* Assume we came from YAMON... */
+	PTR_LA	v0, 0x9fc00534	/* YAMON print */
+	lw	v0, (v0)
+	move	a0, zero
+	PTR_LA  a1, nonsc_processor
+	jal	v0
+
+	PTR_LA	v0, 0x9fc00520	/* YAMON exit */
+	lw	v0, (v0)
+	li	a0, 1
+	jal	v0
+
+1:	b	1b
+	nop
+	__INITDATA
+nonsc_processor:
+	.asciz  "EVA kernel requires a MIPS core with Segment Control implemented\n"
+	__FINIT
+#endif /* CONFIG_EVA */
+0:
+	.endm
+
+/*
+ * Do SMP slave processor setup necessary before we can safely execute C code.
+ */
+	.macro	smp_slave_setup
+#ifdef CONFIG_EVA
+	sync
+	ehb
+	platform_eva_init
+#endif
+	.endm
+
+#endif /* __ASM_MACH_MIPS_KERNEL_ENTRY_INIT_H */
diff --git a/arch/mips/include/asm/mach-malta/mach-gt64120.h b/arch/mips/include/asm/mach-malta/mach-gt64120.h
new file mode 100644
index 000000000..b9dee7c3e
--- /dev/null
+++ b/arch/mips/include/asm/mach-malta/mach-gt64120.h
@@ -0,0 +1,20 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ *  This is a direct copy of the ev96100.h file, with a global
+ * search and replace.	The numbers are the same.
+ *
+ *  The reason I'm duplicating this is so that the 64120/96100
+ * defines won't be confusing in the source code.
+ */
+#ifndef _ASM_MACH_MIPS_MACH_GT64120_DEP_H
+#define _ASM_MACH_MIPS_MACH_GT64120_DEP_H
+
+#define MIPS_GT_BASE	0x1be00000
+
+extern unsigned long _pcictrl_gt64120;
+/*
+ *   GT64120 config space base address
+ */
+#define GT64120_BASE	_pcictrl_gt64120
+
+#endif /* _ASM_MACH_MIPS_MACH_GT64120_DEP_H */
diff --git a/arch/mips/include/asm/mach-malta/mc146818rtc.h b/arch/mips/include/asm/mach-malta/mc146818rtc.h
new file mode 100644
index 000000000..e8cc7fdf7
--- /dev/null
+++ b/arch/mips/include/asm/mach-malta/mc146818rtc.h
@@ -0,0 +1,36 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 1999,2000 MIPS Technologies, Inc.  All rights reserved.
+ * Copyright (C) 2003 by Ralf Baechle
+ *
+ * RTC routines for Malta style attached PIIX4 device, which contains a
+ * Motorola MC146818A-compatible Real Time Clock.
+ */
+#ifndef __ASM_MACH_MALTA_MC146818RTC_H
+#define __ASM_MACH_MALTA_MC146818RTC_H
+
+#include <asm/io.h>
+#include <asm/mips-boards/generic.h>
+#include <asm/mips-boards/malta.h>
+
+#define RTC_PORT(x)	(0x70 + (x))
+#define RTC_IRQ		8
+
+static inline unsigned char CMOS_READ(unsigned long addr)
+{
+	outb(addr, MALTA_RTC_ADR_REG);
+	return inb(MALTA_RTC_DAT_REG);
+}
+
+static inline void CMOS_WRITE(unsigned char data, unsigned long addr)
+{
+	outb(addr, MALTA_RTC_ADR_REG);
+	outb(data, MALTA_RTC_DAT_REG);
+}
+
+#define RTC_ALWAYS_BCD	0
+
+#define mc146818_decode_year(year) ((year) < 70 ? (year) + 2000 : (year) + 1900)
+
+#endif /* __ASM_MACH_MALTA_MC146818RTC_H */
diff --git a/arch/mips/include/asm/mach-malta/spaces.h b/arch/mips/include/asm/mach-malta/spaces.h
new file mode 100644
index 000000000..d7e54971e
--- /dev/null
+++ b/arch/mips/include/asm/mach-malta/spaces.h
@@ -0,0 +1,46 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2014 Imagination Technologies Ltd.
+ */
+
+#ifndef _ASM_MALTA_SPACES_H
+#define _ASM_MALTA_SPACES_H
+
+#ifdef CONFIG_EVA
+
+/*
+ * Traditional Malta Board Memory Map for EVA
+ *
+ * 0x00000000 - 0x0fffffff: 1st RAM region, 256MB
+ * 0x10000000 - 0x1bffffff: GIC and CPC Control Registers
+ * 0x1c000000 - 0x1fffffff: I/O And Flash
+ * 0x20000000 - 0x7fffffff: 2nd RAM region, 1.5GB
+ * 0x80000000 - 0xffffffff: Physical memory aliases to 0x0 (2GB)
+ *
+ * The kernel is still located in 0x80000000(kseg0). However,
+ * the physical mask has been shifted to 0x80000000 which exploits the alias
+ * on the Malta board. As a result of which, we override the __pa_symbol
+ * to peform direct mapping from virtual to physical addresses. In other
+ * words, the 0x80000000 virtual address maps to 0x80000000 physical address
+ * which in turn aliases to 0x0. We do this in order to be able to use a flat
+ * 2GB of memory (0x80000000 - 0xffffffff) so we can avoid the I/O hole in
+ * 0x10000000 - 0x1fffffff.
+ * The last 64KB of physical memory are reserved for correct HIGHMEM
+ * macros arithmetics.
+ *
+ */
+
+#define PAGE_OFFSET	_AC(0x0, UL)
+#define PHYS_OFFSET	_AC(0x80000000, UL)
+#define HIGHMEM_START	_AC(0xffff0000, UL)
+
+#define __pa_symbol(x)	(RELOC_HIDE((unsigned long)(x), 0))
+
+#endif /* CONFIG_EVA */
+
+#include <asm/mach-generic/spaces.h>
+
+#endif /* _ASM_MALTA_SPACES_H */
diff --git a/arch/mips/include/asm/mach-n64/irq.h b/arch/mips/include/asm/mach-n64/irq.h
new file mode 100644
index 000000000..7e260fcb2
--- /dev/null
+++ b/arch/mips/include/asm/mach-n64/irq.h
@@ -0,0 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_MACH_N64_IRQ_H
+#define __ASM_MACH_N64_IRQ_H
+
+#define NR_IRQS 8
+
+#include <asm/mach-generic/irq.h>
+
+#endif /* __ASM_MACH_N64_IRQ_H */
diff --git a/arch/mips/include/asm/mach-n64/kmalloc.h b/arch/mips/include/asm/mach-n64/kmalloc.h
new file mode 100644
index 000000000..e8b8d0b19
--- /dev/null
+++ b/arch/mips/include/asm/mach-n64/kmalloc.h
@@ -0,0 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_MACH_N64_KMALLOC_H
+#define __ASM_MACH_N64_KMALLOC_H
+
+/* The default of 128 bytes wastes too much, use 32 (the largest cacheline, I) */
+#define ARCH_DMA_MINALIGN L1_CACHE_BYTES
+
+#endif /* __ASM_MACH_N64_KMALLOC_H */
diff --git a/arch/mips/include/asm/mach-pic32/cpu-feature-overrides.h b/arch/mips/include/asm/mach-pic32/cpu-feature-overrides.h
new file mode 100644
index 000000000..468230834
--- /dev/null
+++ b/arch/mips/include/asm/mach-pic32/cpu-feature-overrides.h
@@ -0,0 +1,32 @@
+/*
+ * Joshua Henderson <joshua.henderson@microchip.com>
+ * Copyright (C) 2015 Microchip Technology Inc.  All rights reserved.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#ifndef __ASM_MACH_PIC32_CPU_FEATURE_OVERRIDES_H
+#define __ASM_MACH_PIC32_CPU_FEATURE_OVERRIDES_H
+
+/*
+ * CPU feature overrides for PIC32 boards
+ */
+#ifdef CONFIG_CPU_MIPS32
+#define cpu_has_vint		1
+#define cpu_has_veic		0
+#define cpu_has_tlb		1
+#define cpu_has_4kex		1
+#define cpu_has_4k_cache	1
+#define cpu_has_fpu		0
+#define cpu_has_counter		1
+#define cpu_has_llsc		1
+#define cpu_has_nofpuex		0
+#define cpu_icache_snoops_remote_store 1
+#endif
+
+#ifdef CONFIG_CPU_MIPS64
+#error This platform does not support 64bit.
+#endif
+
+#endif /* __ASM_MACH_PIC32_CPU_FEATURE_OVERRIDES_H */
diff --git a/arch/mips/include/asm/mach-pic32/irq.h b/arch/mips/include/asm/mach-pic32/irq.h
new file mode 100644
index 000000000..ddaf999bc
--- /dev/null
+++ b/arch/mips/include/asm/mach-pic32/irq.h
@@ -0,0 +1,14 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Joshua Henderson <joshua.henderson@microchip.com>
+ * Copyright (C) 2015 Microchip Technology Inc.  All rights reserved.
+ */
+#ifndef __ASM_MACH_PIC32_IRQ_H
+#define __ASM_MACH_PIC32_IRQ_H
+
+#define NR_IRQS	256
+#define MIPS_CPU_IRQ_BASE 0
+
+#include <asm/mach-generic/irq.h>
+
+#endif /* __ASM_MACH_PIC32_IRQ_H */
diff --git a/arch/mips/include/asm/mach-pic32/pic32.h b/arch/mips/include/asm/mach-pic32/pic32.h
new file mode 100644
index 000000000..53918a671
--- /dev/null
+++ b/arch/mips/include/asm/mach-pic32/pic32.h
@@ -0,0 +1,36 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Joshua Henderson <joshua.henderson@microchip.com>
+ * Copyright (C) 2015 Microchip Technology Inc.  All rights reserved.
+ */
+#ifndef _ASM_MACH_PIC32_H
+#define _ASM_MACH_PIC32_H
+
+#include <linux/io.h>
+
+/*
+ * PIC32 register offsets for SET/CLR/INV where supported.
+ */
+#define PIC32_CLR(_reg)		((_reg) + 0x04)
+#define PIC32_SET(_reg)		((_reg) + 0x08)
+#define PIC32_INV(_reg)		((_reg) + 0x0C)
+
+/*
+ * PIC32 Base Register Offsets
+ */
+#define PIC32_BASE_CONFIG	0x1f800000
+#define PIC32_BASE_OSC		0x1f801200
+#define PIC32_BASE_RESET	0x1f801240
+#define PIC32_BASE_PPS		0x1f801400
+#define PIC32_BASE_UART		0x1f822000
+#define PIC32_BASE_PORT		0x1f860000
+#define PIC32_BASE_DEVCFG2	0x1fc4ff44
+
+/*
+ * Register unlock sequence required for some register access.
+ */
+void pic32_syskey_unlock_debug(const char *fn, const ulong ln);
+#define pic32_syskey_unlock()	\
+	pic32_syskey_unlock_debug(__func__, __LINE__)
+
+#endif /* _ASM_MACH_PIC32_H */
diff --git a/arch/mips/include/asm/mach-pic32/spaces.h b/arch/mips/include/asm/mach-pic32/spaces.h
new file mode 100644
index 000000000..eb557b52c
--- /dev/null
+++ b/arch/mips/include/asm/mach-pic32/spaces.h
@@ -0,0 +1,15 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Joshua Henderson <joshua.henderson@microchip.com>
+ * Copyright (C) 2015 Microchip Technology Inc.  All rights reserved.
+ */
+#ifndef _ASM_MACH_PIC32_SPACES_H
+#define _ASM_MACH_PIC32_SPACES_H
+
+#ifdef CONFIG_PIC32MZDA
+#define PHYS_OFFSET	_AC(0x08000000, UL)
+#endif
+
+#include <asm/mach-generic/spaces.h>
+
+#endif /* __ASM_MACH_PIC32_SPACES_H */
diff --git a/arch/mips/include/asm/mach-ralink/irq.h b/arch/mips/include/asm/mach-ralink/irq.h
new file mode 100644
index 000000000..2262243d1
--- /dev/null
+++ b/arch/mips/include/asm/mach-ralink/irq.h
@@ -0,0 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_MACH_RALINK_IRQ_H
+#define __ASM_MACH_RALINK_IRQ_H
+
+#define GIC_NUM_INTRS	64
+#define NR_IRQS 256
+
+#include <asm/mach-generic/irq.h>
+
+#endif
diff --git a/arch/mips/include/asm/mach-ralink/mt7620.h b/arch/mips/include/asm/mach-ralink/mt7620.h
new file mode 100644
index 000000000..d51dfad8f
--- /dev/null
+++ b/arch/mips/include/asm/mach-ralink/mt7620.h
@@ -0,0 +1,99 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *
+ * Parts of this file are based on Ralink's 2.6.21 BSP
+ *
+ * Copyright (C) 2008-2011 Gabor Juhos <juhosg@openwrt.org>
+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ * Copyright (C) 2013 John Crispin <john@phrozen.org>
+ */
+
+#ifndef _MT7620_REGS_H_
+#define _MT7620_REGS_H_
+
+#define MT7620_SYSC_BASE		0x10000000
+
+#define SYSC_REG_CHIP_NAME0		0x00
+#define SYSC_REG_CHIP_NAME1		0x04
+#define SYSC_REG_EFUSE_CFG		0x08
+#define SYSC_REG_CHIP_REV		0x0c
+#define SYSC_REG_SYSTEM_CONFIG0		0x10
+#define SYSC_REG_SYSTEM_CONFIG1		0x14
+#define SYSC_REG_CLKCFG0		0x2c
+#define SYSC_REG_CPU_SYS_CLKCFG		0x3c
+#define SYSC_REG_CPLL_CONFIG0		0x54
+#define SYSC_REG_CPLL_CONFIG1		0x58
+
+#define MT7620_CHIP_NAME0		0x3637544d
+#define MT7620_CHIP_NAME1		0x20203032
+#define MT7628_CHIP_NAME1		0x20203832
+
+#define SYSCFG0_XTAL_FREQ_SEL		BIT(6)
+
+#define CHIP_REV_PKG_MASK		0x1
+#define CHIP_REV_PKG_SHIFT		16
+#define CHIP_REV_VER_MASK		0xf
+#define CHIP_REV_VER_SHIFT		8
+#define CHIP_REV_ECO_MASK		0xf
+
+#define CLKCFG0_PERI_CLK_SEL		BIT(4)
+
+#define CPU_SYS_CLKCFG_OCP_RATIO_SHIFT	16
+#define CPU_SYS_CLKCFG_OCP_RATIO_MASK	0xf
+#define CPU_SYS_CLKCFG_OCP_RATIO_1	0	/* 1:1   (Reserved) */
+#define CPU_SYS_CLKCFG_OCP_RATIO_1_5	1	/* 1:1.5 (Reserved) */
+#define CPU_SYS_CLKCFG_OCP_RATIO_2	2	/* 1:2   */
+#define CPU_SYS_CLKCFG_OCP_RATIO_2_5	3       /* 1:2.5 (Reserved) */
+#define CPU_SYS_CLKCFG_OCP_RATIO_3	4	/* 1:3   */
+#define CPU_SYS_CLKCFG_OCP_RATIO_3_5	5	/* 1:3.5 (Reserved) */
+#define CPU_SYS_CLKCFG_OCP_RATIO_4	6	/* 1:4   */
+#define CPU_SYS_CLKCFG_OCP_RATIO_5	7	/* 1:5   */
+#define CPU_SYS_CLKCFG_OCP_RATIO_10	8	/* 1:10  */
+#define CPU_SYS_CLKCFG_CPU_FDIV_SHIFT	8
+#define CPU_SYS_CLKCFG_CPU_FDIV_MASK	0x1f
+#define CPU_SYS_CLKCFG_CPU_FFRAC_SHIFT	0
+#define CPU_SYS_CLKCFG_CPU_FFRAC_MASK	0x1f
+
+#define CPLL_CFG0_SW_CFG		BIT(31)
+#define CPLL_CFG0_PLL_MULT_RATIO_SHIFT	16
+#define CPLL_CFG0_PLL_MULT_RATIO_MASK   0x7
+#define CPLL_CFG0_LC_CURFCK		BIT(15)
+#define CPLL_CFG0_BYPASS_REF_CLK	BIT(14)
+#define CPLL_CFG0_PLL_DIV_RATIO_SHIFT	10
+#define CPLL_CFG0_PLL_DIV_RATIO_MASK	0x3
+
+#define CPLL_CFG1_CPU_AUX1		BIT(25)
+#define CPLL_CFG1_CPU_AUX0		BIT(24)
+
+#define SYSCFG0_DRAM_TYPE_MASK		0x3
+#define SYSCFG0_DRAM_TYPE_SHIFT		4
+#define SYSCFG0_DRAM_TYPE_SDRAM		0
+#define SYSCFG0_DRAM_TYPE_DDR1		1
+#define SYSCFG0_DRAM_TYPE_DDR2		2
+#define SYSCFG0_DRAM_TYPE_UNKNOWN	3
+
+#define SYSCFG0_DRAM_TYPE_DDR2_MT7628	0
+#define SYSCFG0_DRAM_TYPE_DDR1_MT7628	1
+
+#define MT7620_DRAM_BASE		0x0
+#define MT7620_SDRAM_SIZE_MIN		2
+#define MT7620_SDRAM_SIZE_MAX		64
+#define MT7620_DDR1_SIZE_MIN		32
+#define MT7620_DDR1_SIZE_MAX		128
+#define MT7620_DDR2_SIZE_MIN		32
+#define MT7620_DDR2_SIZE_MAX		256
+
+extern enum ralink_soc_type ralink_soc;
+
+static inline int is_mt76x8(void)
+{
+	return ralink_soc == MT762X_SOC_MT7628AN ||
+	       ralink_soc == MT762X_SOC_MT7688;
+}
+
+static inline int mt7620_get_eco(void)
+{
+	return rt_sysc_r32(SYSC_REG_CHIP_REV) & CHIP_REV_ECO_MASK;
+}
+
+#endif
diff --git a/arch/mips/include/asm/mach-ralink/mt7620/cpu-feature-overrides.h b/arch/mips/include/asm/mach-ralink/mt7620/cpu-feature-overrides.h
new file mode 100644
index 000000000..85a62c99a
--- /dev/null
+++ b/arch/mips/include/asm/mach-ralink/mt7620/cpu-feature-overrides.h
@@ -0,0 +1,51 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Ralink MT7620 specific CPU feature overrides
+ *
+ * Copyright (C) 2008-2009 Gabor Juhos <juhosg@openwrt.org>
+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ *
+ * This file was derived from: include/asm-mips/cpu-features.h
+ *	Copyright (C) 2003, 2004 Ralf Baechle
+ *	Copyright (C) 2004 Maciej W. Rozycki
+ */
+#ifndef _MT7620_CPU_FEATURE_OVERRIDES_H
+#define _MT7620_CPU_FEATURE_OVERRIDES_H
+
+#define cpu_has_tlb		1
+#define cpu_has_4kex		1
+#define cpu_has_3k_cache	0
+#define cpu_has_4k_cache	1
+#define cpu_has_sb1_cache	0
+#define cpu_has_fpu		0
+#define cpu_has_32fpr		0
+#define cpu_has_counter		1
+#define cpu_has_watch		1
+#define cpu_has_divec		1
+
+#define cpu_has_prefetch	1
+#define cpu_has_ejtag		1
+#define cpu_has_llsc		1
+
+#define cpu_has_mips16		1
+#define cpu_has_mdmx		0
+#define cpu_has_mips3d		0
+#define cpu_has_smartmips	0
+
+#define cpu_has_mips32r1	1
+#define cpu_has_mips32r2	1
+#define cpu_has_mips64r1	0
+#define cpu_has_mips64r2	0
+
+#define cpu_has_dsp		1
+#define cpu_has_dsp2		0
+#define cpu_has_mipsmt		0
+
+#define cpu_has_64bits		0
+#define cpu_has_64bit_zero_reg	0
+#define cpu_has_64bit_gp_regs	0
+
+#define cpu_dcache_line_size()	32
+#define cpu_icache_line_size()	32
+
+#endif /* _MT7620_CPU_FEATURE_OVERRIDES_H */
diff --git a/arch/mips/include/asm/mach-ralink/mt7621.h b/arch/mips/include/asm/mach-ralink/mt7621.h
new file mode 100644
index 000000000..79d5bb0e0
--- /dev/null
+++ b/arch/mips/include/asm/mach-ralink/mt7621.h
@@ -0,0 +1,37 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *
+ * Copyright (C) 2015 John Crispin <john@phrozen.org>
+ */
+
+#ifndef _MT7621_REGS_H_
+#define _MT7621_REGS_H_
+
+#define IOMEM(x)			((void __iomem *)(KSEG1ADDR(x)))
+
+#define MT7621_PALMBUS_BASE		0x1C000000
+#define MT7621_PALMBUS_SIZE		0x03FFFFFF
+
+#define MT7621_SYSC_BASE		IOMEM(0x1E000000)
+
+#define SYSC_REG_CHIP_NAME0		0x00
+#define SYSC_REG_CHIP_NAME1		0x04
+#define SYSC_REG_CHIP_REV		0x0c
+#define SYSC_REG_SYSTEM_CONFIG0		0x10
+#define SYSC_REG_SYSTEM_CONFIG1		0x14
+
+#define CHIP_REV_PKG_MASK		0x1
+#define CHIP_REV_PKG_SHIFT		16
+#define CHIP_REV_VER_MASK		0xf
+#define CHIP_REV_VER_SHIFT		8
+#define CHIP_REV_ECO_MASK		0xf
+
+#define MT7621_LOWMEM_BASE		0x0
+#define MT7621_LOWMEM_MAX_SIZE		0x1C000000
+#define MT7621_HIGHMEM_BASE		0x20000000
+#define MT7621_HIGHMEM_SIZE		0x4000000
+
+#define MT7621_CHIP_NAME0		0x3637544D
+#define MT7621_CHIP_NAME1		0x20203132
+
+#endif
diff --git a/arch/mips/include/asm/mach-ralink/mt7621/cpu-feature-overrides.h b/arch/mips/include/asm/mach-ralink/mt7621/cpu-feature-overrides.h
new file mode 100644
index 000000000..3c19a94f5
--- /dev/null
+++ b/arch/mips/include/asm/mach-ralink/mt7621/cpu-feature-overrides.h
@@ -0,0 +1,59 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Ralink MT7621 specific CPU feature overrides
+ *
+ * Copyright (C) 2008-2009 Gabor Juhos <juhosg@openwrt.org>
+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ * Copyright (C) 2015 Felix Fietkau <nbd@openwrt.org>
+ *
+ * This file was derived from: include/asm-mips/cpu-features.h
+ *	Copyright (C) 2003, 2004 Ralf Baechle
+ *	Copyright (C) 2004 Maciej W. Rozycki
+ */
+#ifndef _MT7621_CPU_FEATURE_OVERRIDES_H
+#define _MT7621_CPU_FEATURE_OVERRIDES_H
+
+#define cpu_has_tlb		1
+#define cpu_has_4kex		1
+#define cpu_has_3k_cache	0
+#define cpu_has_4k_cache	1
+#define cpu_has_sb1_cache	0
+#define cpu_has_fpu		0
+#define cpu_has_32fpr		0
+#define cpu_has_counter		1
+#define cpu_has_watch		1
+#define cpu_has_divec		1
+
+#define cpu_has_prefetch	1
+#define cpu_has_ejtag		1
+#define cpu_has_llsc		1
+
+#define cpu_has_mips16		1
+#define cpu_has_mdmx		0
+#define cpu_has_mips3d		0
+#define cpu_has_smartmips	0
+
+#define cpu_has_mips32r1	1
+#define cpu_has_mips32r2	1
+#define cpu_has_mips64r1	0
+#define cpu_has_mips64r2	0
+
+#define cpu_has_dsp		1
+#define cpu_has_dsp2		0
+#define cpu_has_mipsmt		1
+
+#define cpu_has_64bits		0
+#define cpu_has_64bit_zero_reg	0
+#define cpu_has_64bit_gp_regs	0
+
+#define cpu_dcache_line_size()	32
+#define cpu_icache_line_size()	32
+
+#define cpu_has_dc_aliases	0
+#define cpu_has_vtag_icache	0
+
+#define cpu_has_rixi		0
+#define cpu_has_tlbinv		0
+#define cpu_has_userlocal	1
+
+#endif /* _MT7621_CPU_FEATURE_OVERRIDES_H */
diff --git a/arch/mips/include/asm/mach-ralink/ralink_regs.h b/arch/mips/include/asm/mach-ralink/ralink_regs.h
new file mode 100644
index 000000000..9dbd9f087
--- /dev/null
+++ b/arch/mips/include/asm/mach-ralink/ralink_regs.h
@@ -0,0 +1,62 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *  Ralink SoC register definitions
+ *
+ *  Copyright (C) 2013 John Crispin <john@phrozen.org>
+ *  Copyright (C) 2008-2010 Gabor Juhos <juhosg@openwrt.org>
+ *  Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ */
+
+#ifndef _RALINK_REGS_H_
+#define _RALINK_REGS_H_
+
+#include <linux/io.h>
+
+enum ralink_soc_type {
+	RALINK_UNKNOWN = 0,
+	RT2880_SOC,
+	RT3883_SOC,
+	RT305X_SOC_RT3050,
+	RT305X_SOC_RT3052,
+	RT305X_SOC_RT3350,
+	RT305X_SOC_RT3352,
+	RT305X_SOC_RT5350,
+	MT762X_SOC_MT7620A,
+	MT762X_SOC_MT7620N,
+	MT762X_SOC_MT7621AT,
+	MT762X_SOC_MT7628AN,
+	MT762X_SOC_MT7688,
+};
+extern enum ralink_soc_type ralink_soc;
+
+extern __iomem void *rt_sysc_membase;
+extern __iomem void *rt_memc_membase;
+
+static inline void rt_sysc_w32(u32 val, unsigned reg)
+{
+	__raw_writel(val, rt_sysc_membase + reg);
+}
+
+static inline u32 rt_sysc_r32(unsigned reg)
+{
+	return __raw_readl(rt_sysc_membase + reg);
+}
+
+static inline void rt_sysc_m32(u32 clr, u32 set, unsigned reg)
+{
+	u32 val = rt_sysc_r32(reg) & ~clr;
+
+	__raw_writel(val | set, rt_sysc_membase + reg);
+}
+
+static inline void rt_memc_w32(u32 val, unsigned reg)
+{
+	__raw_writel(val, rt_memc_membase + reg);
+}
+
+static inline u32 rt_memc_r32(unsigned reg)
+{
+	return __raw_readl(rt_memc_membase + reg);
+}
+
+#endif /* _RALINK_REGS_H_ */
diff --git a/arch/mips/include/asm/mach-ralink/rt288x.h b/arch/mips/include/asm/mach-ralink/rt288x.h
new file mode 100644
index 000000000..5f213534f
--- /dev/null
+++ b/arch/mips/include/asm/mach-ralink/rt288x.h
@@ -0,0 +1,42 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *
+ * Parts of this file are based on Ralink's 2.6.21 BSP
+ *
+ * Copyright (C) 2008-2011 Gabor Juhos <juhosg@openwrt.org>
+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ * Copyright (C) 2013 John Crispin <john@phrozen.org>
+ */
+
+#ifndef _RT288X_REGS_H_
+#define _RT288X_REGS_H_
+
+#define RT2880_SYSC_BASE		0x00300000
+
+#define SYSC_REG_CHIP_NAME0		0x00
+#define SYSC_REG_CHIP_NAME1		0x04
+#define SYSC_REG_CHIP_ID		0x0c
+#define SYSC_REG_SYSTEM_CONFIG		0x10
+#define SYSC_REG_CLKCFG			0x30
+
+#define RT2880_CHIP_NAME0		0x38325452
+#define RT2880_CHIP_NAME1		0x20203038
+
+#define CHIP_ID_ID_MASK			0xff
+#define CHIP_ID_ID_SHIFT		8
+#define CHIP_ID_REV_MASK		0xff
+
+#define SYSTEM_CONFIG_CPUCLK_SHIFT	20
+#define SYSTEM_CONFIG_CPUCLK_MASK	0x3
+#define SYSTEM_CONFIG_CPUCLK_250	0x0
+#define SYSTEM_CONFIG_CPUCLK_266	0x1
+#define SYSTEM_CONFIG_CPUCLK_280	0x2
+#define SYSTEM_CONFIG_CPUCLK_300	0x3
+
+#define CLKCFG_SRAM_CS_N_WDT		BIT(9)
+
+#define RT2880_SDRAM_BASE		0x08000000
+#define RT2880_MEM_SIZE_MIN		2
+#define RT2880_MEM_SIZE_MAX		128
+
+#endif
diff --git a/arch/mips/include/asm/mach-ralink/rt288x/cpu-feature-overrides.h b/arch/mips/include/asm/mach-ralink/rt288x/cpu-feature-overrides.h
new file mode 100644
index 000000000..a850c1e46
--- /dev/null
+++ b/arch/mips/include/asm/mach-ralink/rt288x/cpu-feature-overrides.h
@@ -0,0 +1,50 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Ralink RT288x specific CPU feature overrides
+ *
+ * Copyright (C) 2008-2009 Gabor Juhos <juhosg@openwrt.org>
+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ *
+ * This file was derived from: include/asm-mips/cpu-features.h
+ *	Copyright (C) 2003, 2004 Ralf Baechle
+ *	Copyright (C) 2004 Maciej W. Rozycki
+ */
+#ifndef _RT288X_CPU_FEATURE_OVERRIDES_H
+#define _RT288X_CPU_FEATURE_OVERRIDES_H
+
+#define cpu_has_tlb		1
+#define cpu_has_4kex		1
+#define cpu_has_3k_cache	0
+#define cpu_has_4k_cache	1
+#define cpu_has_sb1_cache	0
+#define cpu_has_fpu		0
+#define cpu_has_32fpr		0
+#define cpu_has_counter		1
+#define cpu_has_watch		1
+#define cpu_has_divec		1
+
+#define cpu_has_prefetch	1
+#define cpu_has_ejtag		1
+#define cpu_has_llsc		1
+
+#define cpu_has_mips16		1
+#define cpu_has_mdmx		0
+#define cpu_has_mips3d		0
+#define cpu_has_smartmips	0
+
+#define cpu_has_mips32r1	1
+#define cpu_has_mips32r2	1
+#define cpu_has_mips64r1	0
+#define cpu_has_mips64r2	0
+
+#define cpu_has_dsp		0
+#define cpu_has_mipsmt		0
+
+#define cpu_has_64bits		0
+#define cpu_has_64bit_zero_reg	0
+#define cpu_has_64bit_gp_regs	0
+
+#define cpu_dcache_line_size()	16
+#define cpu_icache_line_size()	16
+
+#endif /* _RT288X_CPU_FEATURE_OVERRIDES_H */
diff --git a/arch/mips/include/asm/mach-ralink/rt305x.h b/arch/mips/include/asm/mach-ralink/rt305x.h
new file mode 100644
index 000000000..4d8e8c8d8
--- /dev/null
+++ b/arch/mips/include/asm/mach-ralink/rt305x.h
@@ -0,0 +1,136 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *
+ * Parts of this file are based on Ralink's 2.6.21 BSP
+ *
+ * Copyright (C) 2008-2011 Gabor Juhos <juhosg@openwrt.org>
+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ * Copyright (C) 2013 John Crispin <john@phrozen.org>
+ */
+
+#ifndef _RT305X_REGS_H_
+#define _RT305X_REGS_H_
+
+extern enum ralink_soc_type ralink_soc;
+
+static inline int soc_is_rt3050(void)
+{
+	return ralink_soc == RT305X_SOC_RT3050;
+}
+
+static inline int soc_is_rt3052(void)
+{
+	return ralink_soc == RT305X_SOC_RT3052;
+}
+
+static inline int soc_is_rt305x(void)
+{
+	return soc_is_rt3050() || soc_is_rt3052();
+}
+
+static inline int soc_is_rt3350(void)
+{
+	return ralink_soc == RT305X_SOC_RT3350;
+}
+
+static inline int soc_is_rt3352(void)
+{
+	return ralink_soc == RT305X_SOC_RT3352;
+}
+
+static inline int soc_is_rt5350(void)
+{
+	return ralink_soc == RT305X_SOC_RT5350;
+}
+
+#define RT305X_SYSC_BASE		0x10000000
+
+#define SYSC_REG_CHIP_NAME0		0x00
+#define SYSC_REG_CHIP_NAME1		0x04
+#define SYSC_REG_CHIP_ID		0x0c
+#define SYSC_REG_SYSTEM_CONFIG		0x10
+
+#define RT3052_CHIP_NAME0		0x30335452
+#define RT3052_CHIP_NAME1		0x20203235
+
+#define RT3350_CHIP_NAME0		0x33335452
+#define RT3350_CHIP_NAME1		0x20203035
+
+#define RT3352_CHIP_NAME0		0x33335452
+#define RT3352_CHIP_NAME1		0x20203235
+
+#define RT5350_CHIP_NAME0		0x33355452
+#define RT5350_CHIP_NAME1		0x20203035
+
+#define CHIP_ID_ID_MASK			0xff
+#define CHIP_ID_ID_SHIFT		8
+#define CHIP_ID_REV_MASK		0xff
+
+#define RT305X_SYSCFG_CPUCLK_SHIFT		18
+#define RT305X_SYSCFG_CPUCLK_MASK		0x1
+#define RT305X_SYSCFG_CPUCLK_LOW		0x0
+#define RT305X_SYSCFG_CPUCLK_HIGH		0x1
+
+#define RT305X_SYSCFG_SRAM_CS0_MODE_SHIFT	2
+#define RT305X_SYSCFG_CPUCLK_MASK		0x1
+#define RT305X_SYSCFG_SRAM_CS0_MODE_WDT		0x1
+
+#define RT3352_SYSCFG0_CPUCLK_SHIFT	8
+#define RT3352_SYSCFG0_CPUCLK_MASK	0x1
+#define RT3352_SYSCFG0_CPUCLK_LOW	0x0
+#define RT3352_SYSCFG0_CPUCLK_HIGH	0x1
+
+#define RT5350_SYSCFG0_CPUCLK_SHIFT	8
+#define RT5350_SYSCFG0_CPUCLK_MASK	0x3
+#define RT5350_SYSCFG0_CPUCLK_360	0x0
+#define RT5350_SYSCFG0_CPUCLK_320	0x2
+#define RT5350_SYSCFG0_CPUCLK_300	0x3
+
+#define RT5350_SYSCFG0_DRAM_SIZE_SHIFT  12
+#define RT5350_SYSCFG0_DRAM_SIZE_MASK   7
+#define RT5350_SYSCFG0_DRAM_SIZE_2M     0
+#define RT5350_SYSCFG0_DRAM_SIZE_8M     1
+#define RT5350_SYSCFG0_DRAM_SIZE_16M    2
+#define RT5350_SYSCFG0_DRAM_SIZE_32M    3
+#define RT5350_SYSCFG0_DRAM_SIZE_64M    4
+
+/* multi function gpio pins */
+#define RT305X_GPIO_I2C_SD		1
+#define RT305X_GPIO_I2C_SCLK		2
+#define RT305X_GPIO_SPI_EN		3
+#define RT305X_GPIO_SPI_CLK		4
+/* GPIO 7-14 is shared between UART0, PCM  and I2S interfaces */
+#define RT305X_GPIO_7			7
+#define RT305X_GPIO_10			10
+#define RT305X_GPIO_14			14
+#define RT305X_GPIO_UART1_TXD		15
+#define RT305X_GPIO_UART1_RXD		16
+#define RT305X_GPIO_JTAG_TDO		17
+#define RT305X_GPIO_JTAG_TDI		18
+#define RT305X_GPIO_MDIO_MDC		22
+#define RT305X_GPIO_MDIO_MDIO		23
+#define RT305X_GPIO_SDRAM_MD16		24
+#define RT305X_GPIO_SDRAM_MD31		39
+#define RT305X_GPIO_GE0_TXD0		40
+#define RT305X_GPIO_GE0_RXCLK		51
+
+#define RT3352_SYSC_REG_SYSCFG0		0x010
+#define RT3352_SYSC_REG_SYSCFG1         0x014
+#define RT3352_SYSC_REG_CLKCFG1         0x030
+#define RT3352_SYSC_REG_RSTCTRL         0x034
+#define RT3352_SYSC_REG_USB_PS          0x05c
+
+#define RT3352_CLKCFG0_XTAL_SEL		BIT(20)
+#define RT3352_CLKCFG1_UPHY0_CLK_EN	BIT(18)
+#define RT3352_CLKCFG1_UPHY1_CLK_EN	BIT(20)
+#define RT3352_RSTCTRL_UHST		BIT(22)
+#define RT3352_RSTCTRL_UDEV		BIT(25)
+#define RT3352_SYSCFG1_USB0_HOST_MODE	BIT(10)
+
+#define RT305X_SDRAM_BASE		0x00000000
+#define RT305X_MEM_SIZE_MIN		2
+#define RT305X_MEM_SIZE_MAX		64
+#define RT3352_MEM_SIZE_MIN		2
+#define RT3352_MEM_SIZE_MAX		256
+
+#endif
diff --git a/arch/mips/include/asm/mach-ralink/rt305x/cpu-feature-overrides.h b/arch/mips/include/asm/mach-ralink/rt305x/cpu-feature-overrides.h
new file mode 100644
index 000000000..2d75264a9
--- /dev/null
+++ b/arch/mips/include/asm/mach-ralink/rt305x/cpu-feature-overrides.h
@@ -0,0 +1,50 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Ralink RT305x specific CPU feature overrides
+ *
+ * Copyright (C) 2008-2009 Gabor Juhos <juhosg@openwrt.org>
+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ *
+ * This file was derived from: include/asm-mips/cpu-features.h
+ *	Copyright (C) 2003, 2004 Ralf Baechle
+ *	Copyright (C) 2004 Maciej W. Rozycki
+ */
+#ifndef _RT305X_CPU_FEATURE_OVERRIDES_H
+#define _RT305X_CPU_FEATURE_OVERRIDES_H
+
+#define cpu_has_tlb		1
+#define cpu_has_4kex		1
+#define cpu_has_3k_cache	0
+#define cpu_has_4k_cache	1
+#define cpu_has_sb1_cache	0
+#define cpu_has_fpu		0
+#define cpu_has_32fpr		0
+#define cpu_has_counter		1
+#define cpu_has_watch		1
+#define cpu_has_divec		1
+
+#define cpu_has_prefetch	1
+#define cpu_has_ejtag		1
+#define cpu_has_llsc		1
+
+#define cpu_has_mips16		1
+#define cpu_has_mdmx		0
+#define cpu_has_mips3d		0
+#define cpu_has_smartmips	0
+
+#define cpu_has_mips32r1	1
+#define cpu_has_mips32r2	1
+#define cpu_has_mips64r1	0
+#define cpu_has_mips64r2	0
+
+#define cpu_has_dsp		1
+#define cpu_has_mipsmt		0
+
+#define cpu_has_64bits		0
+#define cpu_has_64bit_zero_reg	0
+#define cpu_has_64bit_gp_regs	0
+
+#define cpu_dcache_line_size()	32
+#define cpu_icache_line_size()	32
+
+#endif /* _RT305X_CPU_FEATURE_OVERRIDES_H */
diff --git a/arch/mips/include/asm/mach-ralink/rt3883.h b/arch/mips/include/asm/mach-ralink/rt3883.h
new file mode 100644
index 000000000..f250de9c0
--- /dev/null
+++ b/arch/mips/include/asm/mach-ralink/rt3883.h
@@ -0,0 +1,217 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Ralink RT3662/RT3883 SoC register definitions
+ *
+ * Copyright (C) 2011-2012 Gabor Juhos <juhosg@openwrt.org>
+ */
+
+#ifndef _RT3883_REGS_H_
+#define _RT3883_REGS_H_
+
+#include <linux/bitops.h>
+
+#define RT3883_SDRAM_BASE	0x00000000
+#define RT3883_SYSC_BASE	0x10000000
+#define RT3883_TIMER_BASE	0x10000100
+#define RT3883_INTC_BASE	0x10000200
+#define RT3883_MEMC_BASE	0x10000300
+#define RT3883_UART0_BASE	0x10000500
+#define RT3883_PIO_BASE		0x10000600
+#define RT3883_FSCC_BASE	0x10000700
+#define RT3883_NANDC_BASE	0x10000810
+#define RT3883_I2C_BASE		0x10000900
+#define RT3883_I2S_BASE		0x10000a00
+#define RT3883_SPI_BASE		0x10000b00
+#define RT3883_UART1_BASE	0x10000c00
+#define RT3883_PCM_BASE		0x10002000
+#define RT3883_GDMA_BASE	0x10002800
+#define RT3883_CODEC1_BASE	0x10003000
+#define RT3883_CODEC2_BASE	0x10003800
+#define RT3883_FE_BASE		0x10100000
+#define RT3883_ROM_BASE		0x10118000
+#define RT3883_USBDEV_BASE	0x10112000
+#define RT3883_PCI_BASE		0x10140000
+#define RT3883_WLAN_BASE	0x10180000
+#define RT3883_USBHOST_BASE	0x101c0000
+#define RT3883_BOOT_BASE	0x1c000000
+#define RT3883_SRAM_BASE	0x1e000000
+#define RT3883_PCIMEM_BASE	0x20000000
+
+#define RT3883_EHCI_BASE	(RT3883_USBHOST_BASE)
+#define RT3883_OHCI_BASE	(RT3883_USBHOST_BASE + 0x1000)
+
+#define RT3883_SYSC_SIZE	0x100
+#define RT3883_TIMER_SIZE	0x100
+#define RT3883_INTC_SIZE	0x100
+#define RT3883_MEMC_SIZE	0x100
+#define RT3883_UART0_SIZE	0x100
+#define RT3883_UART1_SIZE	0x100
+#define RT3883_PIO_SIZE		0x100
+#define RT3883_FSCC_SIZE	0x100
+#define RT3883_NANDC_SIZE	0x0f0
+#define RT3883_I2C_SIZE		0x100
+#define RT3883_I2S_SIZE		0x100
+#define RT3883_SPI_SIZE		0x100
+#define RT3883_PCM_SIZE		0x800
+#define RT3883_GDMA_SIZE	0x800
+#define RT3883_CODEC1_SIZE	0x800
+#define RT3883_CODEC2_SIZE	0x800
+#define RT3883_FE_SIZE		0x10000
+#define RT3883_ROM_SIZE		0x4000
+#define RT3883_USBDEV_SIZE	0x4000
+#define RT3883_PCI_SIZE		0x40000
+#define RT3883_WLAN_SIZE	0x40000
+#define RT3883_USBHOST_SIZE	0x40000
+#define RT3883_BOOT_SIZE	(32 * 1024 * 1024)
+#define RT3883_SRAM_SIZE	(32 * 1024 * 1024)
+
+/* SYSC registers */
+#define RT3883_SYSC_REG_CHIPID0_3	0x00	/* Chip ID 0 */
+#define RT3883_SYSC_REG_CHIPID4_7	0x04	/* Chip ID 1 */
+#define RT3883_SYSC_REG_REVID		0x0c	/* Chip Revision Identification */
+#define RT3883_SYSC_REG_SYSCFG0		0x10	/* System Configuration 0 */
+#define RT3883_SYSC_REG_SYSCFG1		0x14	/* System Configuration 1 */
+#define RT3883_SYSC_REG_CLKCFG0		0x2c	/* Clock Configuration 0 */
+#define RT3883_SYSC_REG_CLKCFG1		0x30	/* Clock Configuration 1 */
+#define RT3883_SYSC_REG_RSTCTRL		0x34	/* Reset Control*/
+#define RT3883_SYSC_REG_RSTSTAT		0x38	/* Reset Status*/
+#define RT3883_SYSC_REG_USB_PS		0x5c	/* USB Power saving control */
+#define RT3883_SYSC_REG_GPIO_MODE	0x60	/* GPIO Purpose Select */
+#define RT3883_SYSC_REG_PCIE_CLK_GEN0	0x7c
+#define RT3883_SYSC_REG_PCIE_CLK_GEN1	0x80
+#define RT3883_SYSC_REG_PCIE_CLK_GEN2	0x84
+#define RT3883_SYSC_REG_PMU		0x88
+#define RT3883_SYSC_REG_PMU1		0x8c
+
+#define RT3883_CHIP_NAME0		0x38335452
+#define RT3883_CHIP_NAME1		0x20203338
+
+#define RT3883_REVID_VER_ID_MASK	0x0f
+#define RT3883_REVID_VER_ID_SHIFT	8
+#define RT3883_REVID_ECO_ID_MASK	0x0f
+
+#define RT3883_SYSCFG0_DRAM_TYPE_DDR2	BIT(17)
+#define RT3883_SYSCFG0_CPUCLK_SHIFT	8
+#define RT3883_SYSCFG0_CPUCLK_MASK	0x3
+#define RT3883_SYSCFG0_CPUCLK_250	0x0
+#define RT3883_SYSCFG0_CPUCLK_384	0x1
+#define RT3883_SYSCFG0_CPUCLK_480	0x2
+#define RT3883_SYSCFG0_CPUCLK_500	0x3
+
+#define RT3883_SYSCFG1_USB0_HOST_MODE	BIT(10)
+#define RT3883_SYSCFG1_PCIE_RC_MODE	BIT(8)
+#define RT3883_SYSCFG1_PCI_HOST_MODE	BIT(7)
+#define RT3883_SYSCFG1_PCI_66M_MODE	BIT(6)
+#define RT3883_SYSCFG1_GPIO2_AS_WDT_OUT	BIT(2)
+
+#define RT3883_CLKCFG1_PCIE_CLK_EN	BIT(21)
+#define RT3883_CLKCFG1_UPHY1_CLK_EN	BIT(20)
+#define RT3883_CLKCFG1_PCI_CLK_EN	BIT(19)
+#define RT3883_CLKCFG1_UPHY0_CLK_EN	BIT(18)
+
+#define RT3883_GPIO_I2C_SD		1
+#define RT3883_GPIO_I2C_SCLK		2
+#define RT3883_GPIO_SPI_CS0		3
+#define RT3883_GPIO_SPI_CLK		4
+#define RT3883_GPIO_SPI_MOSI		5
+#define RT3883_GPIO_SPI_MISO		6
+#define RT3883_GPIO_7			7
+#define RT3883_GPIO_10			10
+#define RT3883_GPIO_11			11
+#define RT3883_GPIO_14			14
+#define RT3883_GPIO_UART1_TXD		15
+#define RT3883_GPIO_UART1_RXD		16
+#define RT3883_GPIO_JTAG_TDO		17
+#define RT3883_GPIO_JTAG_TDI		18
+#define RT3883_GPIO_JTAG_TMS		19
+#define RT3883_GPIO_JTAG_TCLK		20
+#define RT3883_GPIO_JTAG_TRST_N		21
+#define RT3883_GPIO_MDIO_MDC		22
+#define RT3883_GPIO_MDIO_MDIO		23
+#define RT3883_GPIO_LNA_PE_A0		32
+#define RT3883_GPIO_LNA_PE_A1		33
+#define RT3883_GPIO_LNA_PE_A2		34
+#define RT3883_GPIO_LNA_PE_G0		35
+#define RT3883_GPIO_LNA_PE_G1		36
+#define RT3883_GPIO_LNA_PE_G2		37
+#define RT3883_GPIO_PCI_AD0		40
+#define RT3883_GPIO_PCI_AD31		71
+#define RT3883_GPIO_GE2_TXD0		72
+#define RT3883_GPIO_GE2_TXD1		73
+#define RT3883_GPIO_GE2_TXD2		74
+#define RT3883_GPIO_GE2_TXD3		75
+#define RT3883_GPIO_GE2_TXEN		76
+#define RT3883_GPIO_GE2_TXCLK		77
+#define RT3883_GPIO_GE2_RXD0		78
+#define RT3883_GPIO_GE2_RXD1		79
+#define RT3883_GPIO_GE2_RXD2		80
+#define RT3883_GPIO_GE2_RXD3		81
+#define RT3883_GPIO_GE2_RXDV		82
+#define RT3883_GPIO_GE2_RXCLK		83
+#define RT3883_GPIO_GE1_TXD0		84
+#define RT3883_GPIO_GE1_TXD1		85
+#define RT3883_GPIO_GE1_TXD2		86
+#define RT3883_GPIO_GE1_TXD3		87
+#define RT3883_GPIO_GE1_TXEN		88
+#define RT3883_GPIO_GE1_TXCLK		89
+#define RT3883_GPIO_GE1_RXD0		90
+#define RT3883_GPIO_GE1_RXD1		91
+#define RT3883_GPIO_GE1_RXD2		92
+#define RT3883_GPIO_GE1_RXD3		93
+#define RT3883_GPIO_GE1_RXDV		94
+#define RT3883_GPIO_GE1_RXCLK	95
+
+#define RT3883_RSTCTRL_PCIE_PCI_PDM	BIT(27)
+#define RT3883_RSTCTRL_FLASH		BIT(26)
+#define RT3883_RSTCTRL_UDEV		BIT(25)
+#define RT3883_RSTCTRL_PCI		BIT(24)
+#define RT3883_RSTCTRL_PCIE		BIT(23)
+#define RT3883_RSTCTRL_UHST		BIT(22)
+#define RT3883_RSTCTRL_FE		BIT(21)
+#define RT3883_RSTCTRL_WLAN		BIT(20)
+#define RT3883_RSTCTRL_UART1		BIT(29)
+#define RT3883_RSTCTRL_SPI		BIT(18)
+#define RT3883_RSTCTRL_I2S		BIT(17)
+#define RT3883_RSTCTRL_I2C		BIT(16)
+#define RT3883_RSTCTRL_NAND		BIT(15)
+#define RT3883_RSTCTRL_DMA		BIT(14)
+#define RT3883_RSTCTRL_PIO		BIT(13)
+#define RT3883_RSTCTRL_UART		BIT(12)
+#define RT3883_RSTCTRL_PCM		BIT(11)
+#define RT3883_RSTCTRL_MC		BIT(10)
+#define RT3883_RSTCTRL_INTC		BIT(9)
+#define RT3883_RSTCTRL_TIMER		BIT(8)
+#define RT3883_RSTCTRL_SYS		BIT(0)
+
+#define RT3883_INTC_INT_SYSCTL	BIT(0)
+#define RT3883_INTC_INT_TIMER0	BIT(1)
+#define RT3883_INTC_INT_TIMER1	BIT(2)
+#define RT3883_INTC_INT_IA	BIT(3)
+#define RT3883_INTC_INT_PCM	BIT(4)
+#define RT3883_INTC_INT_UART0	BIT(5)
+#define RT3883_INTC_INT_PIO	BIT(6)
+#define RT3883_INTC_INT_DMA	BIT(7)
+#define RT3883_INTC_INT_NAND	BIT(8)
+#define RT3883_INTC_INT_PERFC	BIT(9)
+#define RT3883_INTC_INT_I2S	BIT(10)
+#define RT3883_INTC_INT_UART1	BIT(12)
+#define RT3883_INTC_INT_UHST	BIT(18)
+#define RT3883_INTC_INT_UDEV	BIT(19)
+
+/* FLASH/SRAM/Codec Controller registers */
+#define RT3883_FSCC_REG_FLASH_CFG0	0x00
+#define RT3883_FSCC_REG_FLASH_CFG1	0x04
+#define RT3883_FSCC_REG_CODEC_CFG0	0x40
+#define RT3883_FSCC_REG_CODEC_CFG1	0x44
+
+#define RT3883_FLASH_CFG_WIDTH_SHIFT	26
+#define RT3883_FLASH_CFG_WIDTH_MASK	0x3
+#define RT3883_FLASH_CFG_WIDTH_8BIT	0x0
+#define RT3883_FLASH_CFG_WIDTH_16BIT	0x1
+#define RT3883_FLASH_CFG_WIDTH_32BIT	0x2
+
+#define RT3883_SDRAM_BASE		0x00000000
+#define RT3883_MEM_SIZE_MIN		2
+#define RT3883_MEM_SIZE_MAX		256
+
+#endif /* _RT3883_REGS_H_ */
diff --git a/arch/mips/include/asm/mach-ralink/rt3883/cpu-feature-overrides.h b/arch/mips/include/asm/mach-ralink/rt3883/cpu-feature-overrides.h
new file mode 100644
index 000000000..accf2a325
--- /dev/null
+++ b/arch/mips/include/asm/mach-ralink/rt3883/cpu-feature-overrides.h
@@ -0,0 +1,49 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Ralink RT3662/RT3883 specific CPU feature overrides
+ *
+ * Copyright (C) 2011-2013 Gabor Juhos <juhosg@openwrt.org>
+ *
+ * This file was derived from: include/asm-mips/cpu-features.h
+ *	Copyright (C) 2003, 2004 Ralf Baechle
+ *	Copyright (C) 2004 Maciej W. Rozycki
+ */
+#ifndef _RT3883_CPU_FEATURE_OVERRIDES_H
+#define _RT3883_CPU_FEATURE_OVERRIDES_H
+
+#define cpu_has_tlb		1
+#define cpu_has_4kex		1
+#define cpu_has_3k_cache	0
+#define cpu_has_4k_cache	1
+#define cpu_has_sb1_cache	0
+#define cpu_has_fpu		0
+#define cpu_has_32fpr		0
+#define cpu_has_counter		1
+#define cpu_has_watch		1
+#define cpu_has_divec		1
+
+#define cpu_has_prefetch	1
+#define cpu_has_ejtag		1
+#define cpu_has_llsc		1
+
+#define cpu_has_mips16		1
+#define cpu_has_mdmx		0
+#define cpu_has_mips3d		0
+#define cpu_has_smartmips	0
+
+#define cpu_has_mips32r1	1
+#define cpu_has_mips32r2	1
+#define cpu_has_mips64r1	0
+#define cpu_has_mips64r2	0
+
+#define cpu_has_dsp		1
+#define cpu_has_mipsmt		0
+
+#define cpu_has_64bits		0
+#define cpu_has_64bit_zero_reg	0
+#define cpu_has_64bit_gp_regs	0
+
+#define cpu_dcache_line_size()	32
+#define cpu_icache_line_size()	32
+
+#endif /* _RT3883_CPU_FEATURE_OVERRIDES_H */
diff --git a/arch/mips/include/asm/mach-ralink/spaces.h b/arch/mips/include/asm/mach-ralink/spaces.h
new file mode 100644
index 000000000..a9f0570d0
--- /dev/null
+++ b/arch/mips/include/asm/mach-ralink/spaces.h
@@ -0,0 +1,14 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_MACH_RALINK_SPACES_H_
+#define __ASM_MACH_RALINK_SPACES_H_
+
+#define PCI_IOBASE	mips_io_port_base
+#define PCI_IOSIZE	SZ_64K
+#define IO_SPACE_LIMIT	(PCI_IOSIZE - 1)
+
+#ifdef CONFIG_PCI_DRIVERS_GENERIC
+#define pci_remap_iospace pci_remap_iospace
+#endif
+
+#include <asm/mach-generic/spaces.h>
+#endif
diff --git a/arch/mips/include/asm/mach-rc32434/cpu-feature-overrides.h b/arch/mips/include/asm/mach-rc32434/cpu-feature-overrides.h
new file mode 100644
index 000000000..36d45c9cf
--- /dev/null
+++ b/arch/mips/include/asm/mach-rc32434/cpu-feature-overrides.h
@@ -0,0 +1,62 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ *  IDT RC32434 specific CPU feature overrides
+ *
+ *  Copyright (C) 2008 Florian Fainelli <florian@openwrt.org>
+ *
+ *  This file was derived from: include/asm-mips/cpu-features.h
+ *	Copyright (C) 2003, 2004 Ralf Baechle
+ *	Copyright (C) 2004 Maciej W. Rozycki
+ */
+#ifndef __ASM_MACH_RC32434_CPU_FEATURE_OVERRIDES_H
+#define __ASM_MACH_RC32434_CPU_FEATURE_OVERRIDES_H
+
+/*
+ * The IDT RC32434 SOC has a built-in MIPS 4Kc core.
+ */
+#define cpu_has_tlb			1
+#define cpu_has_4kex			1
+#define cpu_has_3k_cache		0
+#define cpu_has_4k_cache		1
+#define cpu_has_sb1_cache		0
+#define cpu_has_fpu			0
+#define cpu_has_32fpr			0
+#define cpu_has_counter			1
+#define cpu_has_watch			1
+#define cpu_has_divec			1
+#define cpu_has_vce			0
+#define cpu_has_cache_cdex_p		0
+#define cpu_has_cache_cdex_s		0
+#define cpu_has_prefetch		1
+#define cpu_has_mcheck			1
+#define cpu_has_ejtag			1
+#define cpu_has_llsc			1
+
+#define cpu_has_mips16			0
+#define cpu_has_mips16e2		0
+#define cpu_has_mdmx			0
+#define cpu_has_mips3d			0
+#define cpu_has_smartmips		0
+
+#define cpu_has_vtag_icache		0
+
+#define cpu_has_mips32r1		1
+#define cpu_has_mips32r2		0
+#define cpu_has_mips64r1		0
+#define cpu_has_mips64r2		0
+
+#define cpu_has_dsp			0
+#define cpu_has_dsp2			0
+#define cpu_has_mipsmt			0
+
+/* #define cpu_has_nofpuex		? */
+#define cpu_has_64bits			0
+#define cpu_has_64bit_zero_reg		0
+#define cpu_has_64bit_gp_regs		0
+
+#define cpu_has_inclusive_pcaches	0
+
+#define cpu_dcache_line_size()		16
+#define cpu_icache_line_size()		16
+
+#endif /* __ASM_MACH_RC32434_CPU_FEATURE_OVERRIDES_H */
diff --git a/arch/mips/include/asm/mach-rc32434/ddr.h b/arch/mips/include/asm/mach-rc32434/ddr.h
new file mode 100644
index 000000000..e1cad0c7f
--- /dev/null
+++ b/arch/mips/include/asm/mach-rc32434/ddr.h
@@ -0,0 +1,141 @@
+/*
+ *  Definitions for the DDR registers
+ *
+ *  Copyright 2002 Ryan Holm <ryan.holmQVist@idt.com>
+ *  Copyright 2008 Florian Fainelli <florian@openwrt.org>
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ */
+
+#ifndef _ASM_RC32434_DDR_H_
+#define _ASM_RC32434_DDR_H_
+
+#include <asm/mach-rc32434/rb.h>
+
+/* DDR register structure */
+struct ddr_ram {
+	u32 ddrbase;
+	u32 ddrmask;
+	u32 res1;
+	u32 res2;
+	u32 ddrc;
+	u32 ddrabase;
+	u32 ddramask;
+	u32 ddramap;
+	u32 ddrcust;
+	u32 ddrrdc;
+	u32 ddrspare;
+};
+
+#define DDR0_PHYS_ADDR		0x18018000
+
+/* DDR banks masks */
+#define DDR_MASK		0xffff0000
+#define DDR0_BASE_MSK		DDR_MASK
+#define DDR1_BASE_MSK		DDR_MASK
+
+/* DDR bank0 registers */
+#define RC32434_DDR0_ATA_BIT		5
+#define RC32434_DDR0_ATA_MSK		0x000000E0
+#define RC32434_DDR0_DBW_BIT		8
+#define RC32434_DDR0_DBW_MSK		0x00000100
+#define RC32434_DDR0_WR_BIT		9
+#define RC32434_DDR0_WR_MSK		0x00000600
+#define RC32434_DDR0_PS_BIT		11
+#define RC32434_DDR0_PS_MSK		0x00001800
+#define RC32434_DDR0_DTYPE_BIT		13
+#define RC32434_DDR0_DTYPE_MSK		0x0000e000
+#define RC32434_DDR0_RFC_BIT		16
+#define RC32434_DDR0_RFC_MSK		0x000f0000
+#define RC32434_DDR0_RP_BIT		20
+#define RC32434_DDR0_RP_MSK		0x00300000
+#define RC32434_DDR0_AP_BIT		22
+#define RC32434_DDR0_AP_MSK		0x00400000
+#define RC32434_DDR0_RCD_BIT		23
+#define RC32434_DDR0_RCD_MSK		0x01800000
+#define RC32434_DDR0_CL_BIT		25
+#define RC32434_DDR0_CL_MSK		0x06000000
+#define RC32434_DDR0_DBM_BIT		27
+#define RC32434_DDR0_DBM_MSK		0x08000000
+#define RC32434_DDR0_SDS_BIT		28
+#define RC32434_DDR0_SDS_MSK		0x10000000
+#define RC32434_DDR0_ATP_BIT		29
+#define RC32434_DDR0_ATP_MSK		0x60000000
+#define RC32434_DDR0_RE_BIT		31
+#define RC32434_DDR0_RE_MSK		0x80000000
+
+/* DDR bank C registers */
+#define RC32434_DDRC_MSK(x)		BIT_TO_MASK(x)
+#define RC32434_DDRC_CES_BIT		0
+#define RC32434_DDRC_ACE_BIT		1
+
+/* Custom DDR bank registers */
+#define RC32434_DCST_MSK(x)		BIT_TO_MASK(x)
+#define RC32434_DCST_CS_BIT		0
+#define RC32434_DCST_CS_MSK		0x00000003
+#define RC32434_DCST_WE_BIT		2
+#define RC32434_DCST_RAS_BIT		3
+#define RC32434_DCST_CAS_BIT		4
+#define RC32434_DSCT_CKE_BIT		5
+#define RC32434_DSCT_BA_BIT		6
+#define RC32434_DSCT_BA_MSK		0x000000c0
+
+/* DDR QSC registers */
+#define RC32434_QSC_DM_BIT		0
+#define RC32434_QSC_DM_MSK		0x00000003
+#define RC32434_QSC_DQSBS_BIT		2
+#define RC32434_QSC_DQSBS_MSK		0x000000fc
+#define RC32434_QSC_DB_BIT		8
+#define RC32434_QSC_DB_MSK		0x00000100
+#define RC32434_QSC_DBSP_BIT		9
+#define RC32434_QSC_DBSP_MSK		0x01fffe00
+#define RC32434_QSC_BDP_BIT		25
+#define RC32434_QSC_BDP_MSK		0x7e000000
+
+/* DDR LLC registers */
+#define RC32434_LLC_EAO_BIT		0
+#define RC32434_LLC_EAO_MSK		0x00000001
+#define RC32434_LLC_EO_BIT		1
+#define RC32434_LLC_EO_MSK		0x0000003e
+#define RC32434_LLC_FS_BIT		6
+#define RC32434_LLC_FS_MSK		0x000000c0
+#define RC32434_LLC_AS_BIT		8
+#define RC32434_LLC_AS_MSK		0x00000700
+#define RC32434_LLC_SP_BIT		11
+#define RC32434_LLC_SP_MSK		0x001ff800
+
+/* DDR LLFC registers */
+#define RC32434_LLFC_MSK(x)		BIT_TO_MASK(x)
+#define RC32434_LLFC_MEN_BIT		0
+#define RC32434_LLFC_EAN_BIT		1
+#define RC32434_LLFC_FF_BIT		2
+
+/* DDR DLLTA registers */
+#define RC32434_DLLTA_ADDR_BIT		2
+#define RC32434_DLLTA_ADDR_MSK		0xfffffffc
+
+/* DDR DLLED registers */
+#define RC32434_DLLED_MSK(x)		BIT_TO_MASK(x)
+#define RC32434_DLLED_DBE_BIT		0
+#define RC32434_DLLED_DTE_BIT		1
+
+#endif	/* _ASM_RC32434_DDR_H_ */
diff --git a/arch/mips/include/asm/mach-rc32434/dma.h b/arch/mips/include/asm/mach-rc32434/dma.h
new file mode 100644
index 000000000..44dc87bb8
--- /dev/null
+++ b/arch/mips/include/asm/mach-rc32434/dma.h
@@ -0,0 +1,104 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright 2002 Integrated Device Technology, Inc.
+ *		All rights reserved.
+ *
+ * DMA register definition.
+ *
+ * Author : ryan.holmQVist@idt.com
+ * Date	  : 20011005
+ */
+
+#ifndef __ASM_RC32434_DMA_H
+#define __ASM_RC32434_DMA_H
+
+#include <asm/mach-rc32434/rb.h>
+
+#define DMA0_BASE_ADDR			0x18040000
+
+/*
+ * DMA descriptor (in physical memory).
+ */
+
+struct dma_desc {
+	u32 control;			/* Control. use DMAD_* */
+	u32 ca;				/* Current Address. */
+	u32 devcs;			/* Device control and status. */
+	u32 link;			/* Next descriptor in chain. */
+};
+
+#define DMA_DESC_SIZ			sizeof(struct dma_desc)
+#define DMA_DESC_COUNT_BIT		0
+#define DMA_DESC_COUNT_MSK		0x0003ffff
+#define DMA_DESC_DS_BIT			20
+#define DMA_DESC_DS_MSK			0x00300000
+
+#define DMA_DESC_DEV_CMD_BIT		22
+#define DMA_DESC_DEV_CMD_MSK		0x01c00000
+
+/* DMA command sizes */
+#define DMA_DESC_DEV_CMD_BYTE		0
+#define DMA_DESC_DEV_CMD_HLF_WD		1
+#define DMA_DESC_DEV_CMD_WORD		2
+#define DMA_DESC_DEV_CMD_2WORDS		3
+#define DMA_DESC_DEV_CMD_4WORDS		4
+#define DMA_DESC_DEV_CMD_6WORDS		5
+#define DMA_DESC_DEV_CMD_8WORDS		6
+#define DMA_DESC_DEV_CMD_16WORDS	7
+
+/* DMA descriptors interrupts */
+#define DMA_DESC_COF			(1 << 25) /* Chain on finished */
+#define DMA_DESC_COD			(1 << 26) /* Chain on done */
+#define DMA_DESC_IOF			(1 << 27) /* Interrupt on finished */
+#define DMA_DESC_IOD			(1 << 28) /* Interrupt on done */
+#define DMA_DESC_TERM			(1 << 29) /* Terminated */
+#define DMA_DESC_DONE			(1 << 30) /* Done */
+#define DMA_DESC_FINI			(1 << 31) /* Finished */
+
+/*
+ * DMA register (within Internal Register Map).
+ */
+
+struct dma_reg {
+	u32 dmac;		/* Control. */
+	u32 dmas;		/* Status. */
+	u32 dmasm;		/* Mask. */
+	u32 dmadptr;		/* Descriptor pointer. */
+	u32 dmandptr;		/* Next descriptor pointer. */
+};
+
+/* DMA channels specific registers */
+#define DMA_CHAN_RUN_BIT		(1 << 0)
+#define DMA_CHAN_DONE_BIT		(1 << 1)
+#define DMA_CHAN_MODE_BIT		(1 << 2)
+#define DMA_CHAN_MODE_MSK		0x0000000c
+#define	 DMA_CHAN_MODE_AUTO		0
+#define	 DMA_CHAN_MODE_BURST		1
+#define	 DMA_CHAN_MODE_XFRT		2
+#define	 DMA_CHAN_MODE_RSVD		3
+#define DMA_CHAN_ACT_BIT		(1 << 4)
+
+/* DMA status registers */
+#define DMA_STAT_FINI			(1 << 0)
+#define DMA_STAT_DONE			(1 << 1)
+#define DMA_STAT_CHAIN			(1 << 2)
+#define DMA_STAT_ERR			(1 << 3)
+#define DMA_STAT_HALT			(1 << 4)
+
+/*
+ * DMA channel definitions
+ */
+
+#define DMA_CHAN_ETH_RCV		0
+#define DMA_CHAN_ETH_XMT		1
+#define DMA_CHAN_MEM_TO_FIFO		2
+#define DMA_CHAN_FIFO_TO_MEM		3
+#define DMA_CHAN_PCI_TO_MEM		4
+#define DMA_CHAN_MEM_TO_PCI		5
+#define DMA_CHAN_COUNT			6
+
+struct dma_channel {
+	struct dma_reg ch[DMA_CHAN_COUNT];
+};
+
+#endif	/* __ASM_RC32434_DMA_H */
diff --git a/arch/mips/include/asm/mach-rc32434/dma_v.h b/arch/mips/include/asm/mach-rc32434/dma_v.h
new file mode 100644
index 000000000..37d73b987
--- /dev/null
+++ b/arch/mips/include/asm/mach-rc32434/dma_v.h
@@ -0,0 +1,53 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright 2002 Integrated Device Technology, Inc.
+ *		All rights reserved.
+ *
+ * DMA register definition.
+ *
+ * Author : ryan.holmQVist@idt.com
+ * Date	  : 20011005
+ */
+
+#ifndef _ASM_RC32434_DMA_V_H_
+#define _ASM_RC32434_DMA_V_H_
+
+#include  <asm/mach-rc32434/dma.h>
+#include  <asm/mach-rc32434/rc32434.h>
+
+#define DMA_CHAN_OFFSET		0x14
+#define IS_DMA_USED(X)		(((X) & \
+				(DMA_DESC_FINI | DMA_DESC_DONE | DMA_DESC_TERM)) \
+				!= 0)
+#define DMA_COUNT(count)	((count) & DMA_DESC_COUNT_MSK)
+
+#define DMA_HALT_TIMEOUT	500
+
+static inline int rc32434_halt_dma(struct dma_reg *ch)
+{
+	int timeout = 1;
+	if (__raw_readl(&ch->dmac) & DMA_CHAN_RUN_BIT) {
+		__raw_writel(0, &ch->dmac);
+		for (timeout = DMA_HALT_TIMEOUT; timeout > 0; timeout--) {
+			if (__raw_readl(&ch->dmas) & DMA_STAT_HALT) {
+				__raw_writel(0, &ch->dmas);
+				break;
+			}
+		}
+	}
+
+	return timeout ? 0 : 1;
+}
+
+static inline void rc32434_start_dma(struct dma_reg *ch, u32 dma_addr)
+{
+	__raw_writel(0, &ch->dmandptr);
+	__raw_writel(dma_addr, &ch->dmadptr);
+}
+
+static inline void rc32434_chain_dma(struct dma_reg *ch, u32 dma_addr)
+{
+	__raw_writel(dma_addr, &ch->dmandptr);
+}
+
+#endif	/* _ASM_RC32434_DMA_V_H_ */
diff --git a/arch/mips/include/asm/mach-rc32434/eth.h b/arch/mips/include/asm/mach-rc32434/eth.h
new file mode 100644
index 000000000..c2645faad
--- /dev/null
+++ b/arch/mips/include/asm/mach-rc32434/eth.h
@@ -0,0 +1,220 @@
+/*
+ *  Definitions for the Ethernet registers
+ *
+ *  Copyright 2002 Allend Stichter <allen.stichter@idt.com>
+ *  Copyright 2008 Florian Fainelli <florian@openwrt.org>
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ */
+
+#ifndef __ASM_RC32434_ETH_H
+#define __ASM_RC32434_ETH_H
+
+
+#define ETH0_BASE_ADDR		0x18060000
+
+struct eth_regs {
+	u32 ethintfc;
+	u32 ethfifott;
+	u32 etharc;
+	u32 ethhash0;
+	u32 ethhash1;
+	u32 ethu0[4];		/* Reserved. */
+	u32 ethpfs;
+	u32 ethmcp;
+	u32 eth_u1[10];		/* Reserved. */
+	u32 ethspare;
+	u32 eth_u2[42];		/* Reserved. */
+	u32 ethsal0;
+	u32 ethsah0;
+	u32 ethsal1;
+	u32 ethsah1;
+	u32 ethsal2;
+	u32 ethsah2;
+	u32 ethsal3;
+	u32 ethsah3;
+	u32 ethrbc;
+	u32 ethrpc;
+	u32 ethrupc;
+	u32 ethrfc;
+	u32 ethtbc;
+	u32 ethgpf;
+	u32 eth_u9[50];		/* Reserved. */
+	u32 ethmac1;
+	u32 ethmac2;
+	u32 ethipgt;
+	u32 ethipgr;
+	u32 ethclrt;
+	u32 ethmaxf;
+	u32 eth_u10;		/* Reserved. */
+	u32 ethmtest;
+	u32 miimcfg;
+	u32 miimcmd;
+	u32 miimaddr;
+	u32 miimwtd;
+	u32 miimrdd;
+	u32 miimind;
+	u32 eth_u11;		/* Reserved. */
+	u32 eth_u12;		/* Reserved. */
+	u32 ethcfsa0;
+	u32 ethcfsa1;
+	u32 ethcfsa2;
+};
+
+/* Ethernet interrupt registers */
+#define ETH_INT_FC_EN		(1 << 0)
+#define ETH_INT_FC_ITS		(1 << 1)
+#define ETH_INT_FC_RIP		(1 << 2)
+#define ETH_INT_FC_JAM		(1 << 3)
+#define ETH_INT_FC_OVR		(1 << 4)
+#define ETH_INT_FC_UND		(1 << 5)
+#define ETH_INT_FC_IOC		0x000000c0
+
+/* Ethernet FIFO registers */
+#define ETH_FIFI_TT_TTH_BIT	0
+#define ETH_FIFO_TT_TTH		0x0000007f
+
+/* Ethernet ARC/multicast registers */
+#define ETH_ARC_PRO		(1 << 0)
+#define ETH_ARC_AM		(1 << 1)
+#define ETH_ARC_AFM		(1 << 2)
+#define ETH_ARC_AB		(1 << 3)
+
+/* Ethernet SAL registers */
+#define ETH_SAL_BYTE_5		0x000000ff
+#define ETH_SAL_BYTE_4		0x0000ff00
+#define ETH_SAL_BYTE_3		0x00ff0000
+#define ETH_SAL_BYTE_2		0xff000000
+
+/* Ethernet SAH registers */
+#define ETH_SAH_BYTE1		0x000000ff
+#define ETH_SAH_BYTE0		0x0000ff00
+
+/* Ethernet GPF register */
+#define ETH_GPF_PTV		0x0000ffff
+
+/* Ethernet PFG register */
+#define ETH_PFS_PFD		(1 << 0)
+
+/* Ethernet CFSA[0-3] registers */
+#define ETH_CFSA0_CFSA4		0x000000ff
+#define ETH_CFSA0_CFSA5		0x0000ff00
+#define ETH_CFSA1_CFSA2		0x000000ff
+#define ETH_CFSA1_CFSA3		0x0000ff00
+#define ETH_CFSA1_CFSA0		0x000000ff
+#define ETH_CFSA1_CFSA1		0x0000ff00
+
+/* Ethernet MAC1 registers */
+#define ETH_MAC1_RE		(1 << 0)
+#define ETH_MAC1_PAF		(1 << 1)
+#define ETH_MAC1_RFC		(1 << 2)
+#define ETH_MAC1_TFC		(1 << 3)
+#define ETH_MAC1_LB		(1 << 4)
+#define ETH_MAC1_MR		(1 << 31)
+
+/* Ethernet MAC2 registers */
+#define ETH_MAC2_FD		(1 << 0)
+#define ETH_MAC2_FLC		(1 << 1)
+#define ETH_MAC2_HFE		(1 << 2)
+#define ETH_MAC2_DC		(1 << 3)
+#define ETH_MAC2_CEN		(1 << 4)
+#define ETH_MAC2_PE		(1 << 5)
+#define ETH_MAC2_VPE		(1 << 6)
+#define ETH_MAC2_APE		(1 << 7)
+#define ETH_MAC2_PPE		(1 << 8)
+#define ETH_MAC2_LPE		(1 << 9)
+#define ETH_MAC2_NB		(1 << 12)
+#define ETH_MAC2_BP		(1 << 13)
+#define ETH_MAC2_ED		(1 << 14)
+
+/* Ethernet IPGT register */
+#define ETH_IPGT		0x0000007f
+
+/* Ethernet IPGR registers */
+#define ETH_IPGR_IPGR2		0x0000007f
+#define ETH_IPGR_IPGR1		0x00007f00
+
+/* Ethernet CLRT registers */
+#define ETH_CLRT_MAX_RET	0x0000000f
+#define ETH_CLRT_COL_WIN	0x00003f00
+
+/* Ethernet MAXF register */
+#define ETH_MAXF		0x0000ffff
+
+/* Ethernet test registers */
+#define ETH_TEST_REG		(1 << 2)
+#define ETH_MCP_DIV		0x000000ff
+
+/* MII registers */
+#define ETH_MII_CFG_RSVD	0x0000000c
+#define ETH_MII_CMD_RD		(1 << 0)
+#define ETH_MII_CMD_SCN		(1 << 1)
+#define ETH_MII_REG_ADDR	0x0000001f
+#define ETH_MII_PHY_ADDR	0x00001f00
+#define ETH_MII_WTD_DATA	0x0000ffff
+#define ETH_MII_RDD_DATA	0x0000ffff
+#define ETH_MII_IND_BSY		(1 << 0)
+#define ETH_MII_IND_SCN		(1 << 1)
+#define ETH_MII_IND_NV		(1 << 2)
+
+/*
+ * Values for the DEVCS field of the Ethernet DMA Rx and Tx descriptors.
+ */
+
+#define ETH_RX_FD		(1 << 0)
+#define ETH_RX_LD		(1 << 1)
+#define ETH_RX_ROK		(1 << 2)
+#define ETH_RX_FM		(1 << 3)
+#define ETH_RX_MP		(1 << 4)
+#define ETH_RX_BP		(1 << 5)
+#define ETH_RX_VLT		(1 << 6)
+#define ETH_RX_CF		(1 << 7)
+#define ETH_RX_OVR		(1 << 8)
+#define ETH_RX_CRC		(1 << 9)
+#define ETH_RX_CV		(1 << 10)
+#define ETH_RX_DB		(1 << 11)
+#define ETH_RX_LE		(1 << 12)
+#define ETH_RX_LOR		(1 << 13)
+#define ETH_RX_CES		(1 << 14)
+#define ETH_RX_LEN_BIT		16
+#define ETH_RX_LEN		0xffff0000
+
+#define ETH_TX_FD		(1 << 0)
+#define ETH_TX_LD		(1 << 1)
+#define ETH_TX_OEN		(1 << 2)
+#define ETH_TX_PEN		(1 << 3)
+#define ETH_TX_CEN		(1 << 4)
+#define ETH_TX_HEN		(1 << 5)
+#define ETH_TX_TOK		(1 << 6)
+#define ETH_TX_MP		(1 << 7)
+#define ETH_TX_BP		(1 << 8)
+#define ETH_TX_UND		(1 << 9)
+#define ETH_TX_OF		(1 << 10)
+#define ETH_TX_ED		(1 << 11)
+#define ETH_TX_EC		(1 << 12)
+#define ETH_TX_LC		(1 << 13)
+#define ETH_TX_TD		(1 << 14)
+#define ETH_TX_CRC		(1 << 15)
+#define ETH_TX_LE		(1 << 16)
+#define ETH_TX_CC		0x001E0000
+
+#endif	/* __ASM_RC32434_ETH_H */
diff --git a/arch/mips/include/asm/mach-rc32434/gpio.h b/arch/mips/include/asm/mach-rc32434/gpio.h
new file mode 100644
index 000000000..a3192da9f
--- /dev/null
+++ b/arch/mips/include/asm/mach-rc32434/gpio.h
@@ -0,0 +1,79 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright 2002 Integrated Device Technology, Inc.
+ *	All rights reserved.
+ *
+ * GPIO register definition.
+ *
+ * Author : ryan.holmQVist@idt.com
+ * Date	  : 20011005
+ * Copyright (C) 2001, 2002 Ryan Holm <ryan.holmQVist@idt.com>
+ * Copyright (C) 2008 Florian Fainelli <florian@openwrt.org>
+ */
+
+#ifndef _RC32434_GPIO_H_
+#define _RC32434_GPIO_H_
+
+struct rb532_gpio_reg {
+	u32   gpiofunc;	  /* GPIO Function Register
+			   * gpiofunc[x]==0 bit = gpio
+			   * func[x]==1	 bit = altfunc
+			   */
+	u32   gpiocfg;	  /* GPIO Configuration Register
+			   * gpiocfg[x]==0 bit = input
+			   * gpiocfg[x]==1 bit = output
+			   */
+	u32   gpiod;	  /* GPIO Data Register
+			   * gpiod[x] read/write gpio pinX status
+			   */
+	u32   gpioilevel; /* GPIO Interrupt Status Register
+			   * interrupt level (see gpioistat)
+			   */
+	u32   gpioistat;  /* Gpio Interrupt Status Register
+			   * istat[x] = (gpiod[x] == level[x])
+			   * cleared in ISR (STICKY bits)
+			   */
+	u32   gpionmien;  /* GPIO Non-maskable Interrupt Enable Register */
+};
+
+/* UART GPIO signals */
+#define RC32434_UART0_SOUT	(1 << 0)
+#define RC32434_UART0_SIN	(1 << 1)
+#define RC32434_UART0_RTS	(1 << 2)
+#define RC32434_UART0_CTS	(1 << 3)
+
+/* M & P bus GPIO signals */
+#define RC32434_MP_BIT_22	(1 << 4)
+#define RC32434_MP_BIT_23	(1 << 5)
+#define RC32434_MP_BIT_24	(1 << 6)
+#define RC32434_MP_BIT_25	(1 << 7)
+
+/* CPU GPIO signals */
+#define RC32434_CPU_GPIO	(1 << 8)
+
+/* Reserved GPIO signals */
+#define RC32434_AF_SPARE_6	(1 << 9)
+#define RC32434_AF_SPARE_4	(1 << 10)
+#define RC32434_AF_SPARE_3	(1 << 11)
+#define RC32434_AF_SPARE_2	(1 << 12)
+
+/* PCI messaging unit */
+#define RC32434_PCI_MSU_GPIO	(1 << 13)
+
+/* NAND GPIO signals */
+#define GPIO_RDY		8
+#define GPIO_WPX	9
+#define GPIO_ALE		10
+#define GPIO_CLE		11
+
+/* Compact Flash GPIO pin */
+#define CF_GPIO_NUM		13
+
+/* S1 button GPIO (shared with UART0_SIN) */
+#define GPIO_BTN_S1		1
+
+extern void rb532_gpio_set_ilevel(int bit, unsigned gpio);
+extern void rb532_gpio_set_istat(int bit, unsigned gpio);
+extern void rb532_gpio_set_func(unsigned gpio);
+
+#endif /* _RC32434_GPIO_H_ */
diff --git a/arch/mips/include/asm/mach-rc32434/integ.h b/arch/mips/include/asm/mach-rc32434/integ.h
new file mode 100644
index 000000000..fa65bc3d8
--- /dev/null
+++ b/arch/mips/include/asm/mach-rc32434/integ.h
@@ -0,0 +1,59 @@
+/*
+ *  Definitions for the Watchdog registers
+ *
+ *  Copyright 2002 Ryan Holm <ryan.holmQVist@idt.com>
+ *  Copyright 2008 Florian Fainelli <florian@openwrt.org>
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ */
+
+#ifndef __RC32434_INTEG_H__
+#define __RC32434_INTEG_H__
+
+#include <asm/mach-rc32434/rb.h>
+
+#define INTEG0_BASE_ADDR	0x18030030
+
+struct integ {
+	u32 errcs;			/* sticky use ERRCS_ */
+	u32 wtcount;			/* Watchdog timer count reg. */
+	u32 wtcompare;			/* Watchdog timer timeout value. */
+	u32 wtc;			/* Watchdog timer control. use WTC_ */
+};
+
+/* Error counters */
+#define RC32434_ERR_WTO		0
+#define RC32434_ERR_WNE		1
+#define RC32434_ERR_UCW		2
+#define RC32434_ERR_UCR		3
+#define RC32434_ERR_UPW		4
+#define RC32434_ERR_UPR		5
+#define RC32434_ERR_UDW		6
+#define RC32434_ERR_UDR		7
+#define RC32434_ERR_SAE		8
+#define RC32434_ERR_WRE		9
+
+/* Watchdog control bits */
+#define RC32434_WTC_EN		0
+#define RC32434_WTC_TO		1
+
+#endif	/* __RC32434_INTEG_H__ */
diff --git a/arch/mips/include/asm/mach-rc32434/irq.h b/arch/mips/include/asm/mach-rc32434/irq.h
new file mode 100644
index 000000000..ebe32bd5a
--- /dev/null
+++ b/arch/mips/include/asm/mach-rc32434/irq.h
@@ -0,0 +1,37 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_RC32434_IRQ_H
+#define __ASM_RC32434_IRQ_H
+
+#define NR_IRQS 256
+
+#include <asm/mach-generic/irq.h>
+#include <asm/mach-rc32434/rb.h>
+
+/* Interrupt Controller */
+#define IC_GROUP0_PEND		(REGBASE + 0x38000)
+#define IC_GROUP0_MASK		(REGBASE + 0x38008)
+#define IC_GROUP_OFFSET		0x0C
+
+#define NUM_INTR_GROUPS		5
+
+/* 16550 UARTs */
+#define GROUP0_IRQ_BASE		8	/* GRP2 IRQ numbers start here */
+					/* GRP3 IRQ numbers start here */
+#define GROUP1_IRQ_BASE		(GROUP0_IRQ_BASE + 32)
+					/* GRP4 IRQ numbers start here */
+#define GROUP2_IRQ_BASE		(GROUP1_IRQ_BASE + 32)
+					/* GRP5 IRQ numbers start here */
+#define GROUP3_IRQ_BASE		(GROUP2_IRQ_BASE + 32)
+#define GROUP4_IRQ_BASE		(GROUP3_IRQ_BASE + 32)
+
+#define UART0_IRQ		(GROUP3_IRQ_BASE + 0)
+
+#define ETH0_DMA_RX_IRQ		(GROUP1_IRQ_BASE + 0)
+#define ETH0_DMA_TX_IRQ		(GROUP1_IRQ_BASE + 1)
+#define ETH0_RX_OVR_IRQ		(GROUP3_IRQ_BASE + 9)
+#define ETH0_TX_UND_IRQ		(GROUP3_IRQ_BASE + 10)
+
+#define GPIO_MAPPED_IRQ_BASE	GROUP4_IRQ_BASE
+#define GPIO_MAPPED_IRQ_GROUP	4
+
+#endif	/* __ASM_RC32434_IRQ_H */
diff --git a/arch/mips/include/asm/mach-rc32434/pci.h b/arch/mips/include/asm/mach-rc32434/pci.h
new file mode 100644
index 000000000..3eb767c8a
--- /dev/null
+++ b/arch/mips/include/asm/mach-rc32434/pci.h
@@ -0,0 +1,478 @@
+/*
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ * Copyright 2004 IDT Inc. (rischelp@idt.com)
+ *
+ * Initial Release
+ */
+
+#ifndef _ASM_RC32434_PCI_H_
+#define _ASM_RC32434_PCI_H_
+
+#define epld_mask ((volatile unsigned char *)0xB900000d)
+
+#define PCI0_BASE_ADDR		0x18080000
+#define PCI_LBA_COUNT		4
+
+struct pci_map {
+	u32 address;		/* Address. */
+	u32 control;		/* Control. */
+	u32 mapping;		/* mapping. */
+};
+
+struct pci_reg {
+	u32 pcic;
+	u32 pcis;
+	u32 pcism;
+	u32 pcicfga;
+	u32 pcicfgd;
+	volatile struct pci_map pcilba[PCI_LBA_COUNT];
+	u32 pcidac;
+	u32 pcidas;
+	u32 pcidasm;
+	u32 pcidad;
+	u32 pcidma8c;
+	u32 pcidma9c;
+	u32 pcitc;
+};
+
+#define PCI_MSU_COUNT		2
+
+struct pci_msu {
+	u32 pciim[PCI_MSU_COUNT];
+	u32 pciom[PCI_MSU_COUNT];
+	u32 pciid;
+	u32 pciiic;
+	u32 pciiim;
+	u32 pciiod;
+	u32 pciioic;
+	u32 pciioim;
+};
+
+/*
+ * PCI Control Register
+ */
+
+#define PCI_CTL_EN		(1 << 0)
+#define PCI_CTL_TNR		(1 << 1)
+#define PCI_CTL_SCE		(1 << 2)
+#define PCI_CTL_IEN		(1 << 3)
+#define PCI_CTL_AAA		(1 << 4)
+#define PCI_CTL_EAP		(1 << 5)
+#define PCI_CTL_PCIM_BIT	6
+#define PCI_CTL_PCIM		0x000001c0
+
+#define PCI_CTL_PCIM_DIS	0
+#define PCI_CTL_PCIM_TNR	1 /* Satellite - target not ready */
+#define PCI_CTL_PCIM_SUS	2 /* Satellite - suspended CPU. */
+#define PCI_CTL_PCIM_EXT	3 /* Host - external arbiter. */
+#define PCI_CTL PCIM_PRIO	4 /* Host - fixed priority arb. */
+#define PCI_CTL_PCIM_RR		5 /* Host - round robin priority. */
+#define PCI_CTL_PCIM_RSVD6	6
+#define PCI_CTL_PCIM_RSVD7	7
+
+#define PCI_CTL_IGM		(1 << 9)
+
+/*
+ * PCI Status Register
+ */
+
+#define PCI_STAT_EED		(1 << 0)
+#define PCI_STAT_WR		(1 << 1)
+#define PCI_STAT_NMI		(1 << 2)
+#define PCI_STAT_II		(1 << 3)
+#define PCI_STAT_CWE		(1 << 4)
+#define PCI_STAT_CRE		(1 << 5)
+#define PCI_STAT_MDPE		(1 << 6)
+#define PCI_STAT_STA		(1 << 7)
+#define PCI_STAT_RTA		(1 << 8)
+#define PCI_STAT_RMA		(1 << 9)
+#define PCI_STAT_SSE		(1 << 10)
+#define PCI_STAT_OSE		(1 << 11)
+#define PCI_STAT_PE		(1 << 12)
+#define PCI_STAT_TAE		(1 << 13)
+#define PCI_STAT_RLE		(1 << 14)
+#define PCI_STAT_BME		(1 << 15)
+#define PCI_STAT_PRD		(1 << 16)
+#define PCI_STAT_RIP		(1 << 17)
+
+/*
+ * PCI Status Mask Register
+ */
+
+#define PCI_STATM_EED		PCI_STAT_EED
+#define PCI_STATM_WR		PCI_STAT_WR
+#define PCI_STATM_NMI		PCI_STAT_NMI
+#define PCI_STATM_II		PCI_STAT_II
+#define PCI_STATM_CWE		PCI_STAT_CWE
+#define PCI_STATM_CRE		PCI_STAT_CRE
+#define PCI_STATM_MDPE		PCI_STAT_MDPE
+#define PCI_STATM_STA		PCI_STAT_STA
+#define PCI_STATM_RTA		PCI_STAT_RTA
+#define PCI_STATM_RMA		PCI_STAT_RMA
+#define PCI_STATM_SSE		PCI_STAT_SSE
+#define PCI_STATM_OSE		PCI_STAT_OSE
+#define PCI_STATM_PE		PCI_STAT_PE
+#define PCI_STATM_TAE		PCI_STAT_TAE
+#define PCI_STATM_RLE		PCI_STAT_RLE
+#define PCI_STATM_BME		PCI_STAT_BME
+#define PCI_STATM_PRD		PCI_STAT_PRD
+#define PCI_STATM_RIP		PCI_STAT_RIP
+
+/*
+ * PCI Configuration Address Register
+ */
+#define PCI_CFGA_REG_BIT	2
+#define PCI_CFGA_REG		0x000000fc
+#define	 PCI_CFGA_REG_ID	(0x00 >> 2)	/* use PCFGID */
+#define	 PCI_CFGA_REG_04	(0x04 >> 2)	/* use PCFG04_ */
+#define	 PCI_CFGA_REG_08	(0x08 >> 2)	/* use PCFG08_ */
+#define	 PCI_CFGA_REG_0C	(0x0C >> 2)	/* use PCFG0C_ */
+#define	 PCI_CFGA_REG_PBA0	(0x10 >> 2)	/* use PCIPBA_ */
+#define	 PCI_CFGA_REG_PBA1	(0x14 >> 2)	/* use PCIPBA_ */
+#define	 PCI_CFGA_REG_PBA2	(0x18 >> 2)	/* use PCIPBA_ */
+#define	 PCI_CFGA_REG_PBA3	(0x1c >> 2)	/* use PCIPBA_ */
+#define	 PCI_CFGA_REG_SUBSYS	(0x2c >> 2)	/* use PCFGSS_ */
+#define	 PCI_CFGA_REG_3C	(0x3C >> 2)	/* use PCFG3C_ */
+#define	 PCI_CFGA_REG_PBBA0C	(0x44 >> 2)	/* use PCIPBAC_ */
+#define	 PCI_CFGA_REG_PBA0M	(0x48 >> 2)
+#define	 PCI_CFGA_REG_PBA1C	(0x4c >> 2)	/* use PCIPBAC_ */
+#define	 PCI_CFGA_REG_PBA1M	(0x50 >> 2)
+#define	 PCI_CFGA_REG_PBA2C	(0x54 >> 2)	/* use PCIPBAC_ */
+#define	 PCI_CFGA_REG_PBA2M	(0x58 >> 2)
+#define	 PCI_CFGA_REG_PBA3C	(0x5c >> 2)	/* use PCIPBAC_ */
+#define	 PCI_CFGA_REG_PBA3M	(0x60 >> 2)
+#define	 PCI_CFGA_REG_PMGT	(0x64 >> 2)
+#define PCI_CFGA_FUNC_BIT	8
+#define PCI_CFGA_FUNC		0x00000700
+#define PCI_CFGA_DEV_BIT	11
+#define PCI_CFGA_DEV		0x0000f800
+#define PCI_CFGA_DEV_INTERN	0
+#define PCI_CFGA_BUS_BIT	16
+#define PCI CFGA_BUS		0x00ff0000
+#define PCI_CFGA_BUS_TYPE0	0
+#define PCI_CFGA_EN		(1 << 31)
+
+/* PCI CFG04 commands */
+#define PCI_CFG04_CMD_IO_ENA	(1 << 0)
+#define PCI_CFG04_CMD_MEM_ENA	(1 << 1)
+#define PCI_CFG04_CMD_BM_ENA	(1 << 2)
+#define PCI_CFG04_CMD_MW_INV	(1 << 4)
+#define PCI_CFG04_CMD_PAR_ENA	(1 << 6)
+#define PCI_CFG04_CMD_SER_ENA	(1 << 8)
+#define PCI_CFG04_CMD_FAST_ENA	(1 << 9)
+
+/* PCI CFG04 status fields */
+#define PCI_CFG04_STAT_BIT	16
+#define PCI_CFG04_STAT		0xffff0000
+#define PCI_CFG04_STAT_66_MHZ	(1 << 21)
+#define PCI_CFG04_STAT_FBB	(1 << 23)
+#define PCI_CFG04_STAT_MDPE	(1 << 24)
+#define PCI_CFG04_STAT_DST	(1 << 25)
+#define PCI_CFG04_STAT_STA	(1 << 27)
+#define PCI_CFG04_STAT_RTA	(1 << 28)
+#define PCI_CFG04_STAT_RMA	(1 << 29)
+#define PCI_CFG04_STAT_SSE	(1 << 30)
+#define PCI_CFG04_STAT_PE	(1 << 31)
+
+#define PCI_PBA_MSI		(1 << 0)
+#define PCI_PBA_P		(1 << 2)
+
+/* PCI PBAC registers */
+#define PCI_PBAC_MSI		(1 << 0)
+#define PCI_PBAC_P		(1 << 1)
+#define PCI_PBAC_SIZE_BIT	2
+#define PCI_PBAC_SIZE		0x0000007c
+#define PCI_PBAC_SB		(1 << 7)
+#define PCI_PBAC_PP		(1 << 8)
+#define PCI_PBAC_MR_BIT		9
+#define PCI_PBAC_MR		0x00000600
+#define	 PCI_PBAC_MR_RD		0
+#define	 PCI_PBAC_MR_RD_LINE	1
+#define	 PCI_PBAC_MR_RD_MULT	2
+#define PCI_PBAC_MRL		(1 << 11)
+#define PCI_PBAC_MRM		(1 << 12)
+#define PCI_PBAC_TRP		(1 << 13)
+
+#define PCI_CFG40_TRDY_TIM	0x000000ff
+#define PCI_CFG40_RET_LIM	0x0000ff00
+
+/*
+ * PCI Local Base Address [0|1|2|3] Register
+ */
+
+#define PCI_LBA_BADDR_BIT	0
+#define PCI_LBA_BADDR		0xffffff00
+
+/*
+ * PCI Local Base Address Control Register
+ */
+
+#define PCI_LBAC_MSI		(1 << 0)
+#define	 PCI_LBAC_MSI_MEM	0
+#define	 PCI_LBAC_MSI_IO	1
+#define PCI_LBAC_SIZE_BIT	2
+#define PCI_LBAC_SIZE		0x0000007c
+#define PCI_LBAC_SB		(1 << 7)
+#define PCI_LBAC_RT		(1 << 8)
+#define	 PCI_LBAC_RT_NO_PREF	0
+#define	 PCI_LBAC_RT_PREF	1
+
+/*
+ * PCI Local Base Address [0|1|2|3] Mapping Register
+ */
+#define PCI_LBAM_MADDR_BIT	8
+#define PCI_LBAM_MADDR		0xffffff00
+
+/*
+ * PCI Decoupled Access Control Register
+ */
+#define PCI_DAC_DEN		(1 << 0)
+
+/*
+ * PCI Decoupled Access Status Register
+ */
+#define PCI_DAS_D		(1 << 0)
+#define PCI_DAS_B		(1 << 1)
+#define PCI_DAS_E		(1 << 2)
+#define PCI_DAS_OFE		(1 << 3)
+#define PCI_DAS_OFF		(1 << 4)
+#define PCI_DAS_IFE		(1 << 5)
+#define PCI_DAS_IFF		(1 << 6)
+
+/*
+ * PCI DMA Channel 8 Configuration Register
+ */
+#define PCI_DMA8C_MBS_BIT	0
+#define PCI_DMA8C_MBS		0x00000fff /* Maximum Burst Size. */
+#define PCI_DMA8C_OUR		(1 << 12)
+
+/*
+ * PCI DMA Channel 9 Configuration Register
+ */
+#define PCI_DMA9C_MBS_BIT	0	/* Maximum Burst Size. */
+#define PCI_DMA9C_MBS		0x00000fff
+
+/*
+ * PCI to Memory(DMA Channel 8) AND Memory to PCI DMA(DMA Channel 9)Descriptors
+ */
+
+#define PCI_DMAD_PT_BIT		22		/* in DEVCMD field (descriptor) */
+#define PCI_DMAD_PT		0x00c00000	/* preferred transaction field */
+/* These are for reads (DMA channel 8) */
+#define PCI_DMAD_DEVCMD_MR	0		/* memory read */
+#define PCI_DMAD_DEVCMD_MRL	1		/* memory read line */
+#define PCI_DMAD_DEVCMD_MRM	2		/* memory read multiple */
+#define PCI_DMAD_DEVCMD_IOR	3		/* I/O read */
+/* These are for writes (DMA channel 9) */
+#define PCI_DMAD_DEVCMD_MW	0		/* memory write */
+#define PCI_DMAD_DEVCMD_MWI	1		/* memory write invalidate */
+#define PCI_DMAD_DEVCMD_IOW	3		/* I/O write */
+
+/* Swap byte field applies to both DMA channel 8 and 9 */
+#define PCI_DMAD_SB		(1 << 24)	/* swap byte field */
+
+
+/*
+ * PCI Target Control Register
+ */
+
+#define PCI_TC_RTIMER_BIT	0
+#define PCI_TC_RTIMER		0x000000ff
+#define PCI_TC_DTIMER_BIT	8
+#define PCI_TC_DTIMER		0x0000ff00
+#define PCI_TC_RDR		(1 << 18)
+#define PCI_TC_DDT		(1 << 19)
+
+/*
+ * PCI messaging unit [applies to both inbound and outbound registers ]
+ */
+#define PCI_MSU_M0		(1 << 0)
+#define PCI_MSU_M1		(1 << 1)
+#define PCI_MSU_DB		(1 << 2)
+
+#define PCI_MSG_ADDR		0xB8088010
+#define PCI0_ADDR		0xB8080000
+#define rc32434_pci ((struct pci_reg *) PCI0_ADDR)
+#define rc32434_pci_msg ((struct pci_msu *) PCI_MSG_ADDR)
+
+#define PCIM_SHFT		0x6
+#define PCIM_BIT_LEN		0x7
+#define PCIM_H_EA		0x3
+#define PCIM_H_IA_FIX		0x4
+#define PCIM_H_IA_RR		0x5
+
+#define PCI_ADDR_START		0x50000000
+
+#define CPUTOPCI_MEM_WIN	0x02000000
+#define CPUTOPCI_IO_WIN		0x00100000
+#define PCILBA_SIZE_SHFT	2
+#define PCILBA_SIZE_MASK	0x1F
+#define SIZE_256MB		0x1C
+#define SIZE_128MB		0x1B
+#define SIZE_64MB		0x1A
+#define SIZE_32MB		0x19
+#define SIZE_16MB		0x18
+#define SIZE_4MB		0x16
+#define SIZE_2MB		0x15
+#define SIZE_1MB		0x14
+#define KORINA_CONFIG0_ADDR	0x80000000
+#define KORINA_CONFIG1_ADDR	0x80000004
+#define KORINA_CONFIG2_ADDR	0x80000008
+#define KORINA_CONFIG3_ADDR	0x8000000C
+#define KORINA_CONFIG4_ADDR	0x80000010
+#define KORINA_CONFIG5_ADDR	0x80000014
+#define KORINA_CONFIG6_ADDR	0x80000018
+#define KORINA_CONFIG7_ADDR	0x8000001C
+#define KORINA_CONFIG8_ADDR	0x80000020
+#define KORINA_CONFIG9_ADDR	0x80000024
+#define KORINA_CONFIG10_ADDR	0x80000028
+#define KORINA_CONFIG11_ADDR	0x8000002C
+#define KORINA_CONFIG12_ADDR	0x80000030
+#define KORINA_CONFIG13_ADDR	0x80000034
+#define KORINA_CONFIG14_ADDR	0x80000038
+#define KORINA_CONFIG15_ADDR	0x8000003C
+#define KORINA_CONFIG16_ADDR	0x80000040
+#define KORINA_CONFIG17_ADDR	0x80000044
+#define KORINA_CONFIG18_ADDR	0x80000048
+#define KORINA_CONFIG19_ADDR	0x8000004C
+#define KORINA_CONFIG20_ADDR	0x80000050
+#define KORINA_CONFIG21_ADDR	0x80000054
+#define KORINA_CONFIG22_ADDR	0x80000058
+#define KORINA_CONFIG23_ADDR	0x8000005C
+#define KORINA_CONFIG24_ADDR	0x80000060
+#define KORINA_CONFIG25_ADDR	0x80000064
+#define KORINA_CMD		(PCI_CFG04_CMD_IO_ENA | \
+				 PCI_CFG04_CMD_MEM_ENA | \
+				 PCI_CFG04_CMD_BM_ENA | \
+				 PCI_CFG04_CMD_MW_INV | \
+				 PCI_CFG04_CMD_PAR_ENA | \
+				 PCI_CFG04_CMD_SER_ENA)
+
+#define KORINA_STAT		(PCI_CFG04_STAT_MDPE | \
+				 PCI_CFG04_STAT_STA | \
+				 PCI_CFG04_STAT_RTA | \
+				 PCI_CFG04_STAT_RMA | \
+				 PCI_CFG04_STAT_SSE | \
+				 PCI_CFG04_STAT_PE)
+
+#define KORINA_CNFG1		(KORINA_STAT | KORINA_CMD)
+
+#define KORINA_REVID		0
+#define KORINA_CLASS_CODE	0
+#define KORINA_CNFG2		((KORINA_CLASS_CODE<<8) | \
+				  KORINA_REVID)
+
+#define KORINA_CACHE_LINE_SIZE	4
+#define KORINA_MASTER_LAT	0x3c
+#define KORINA_HEADER_TYPE	0
+#define KORINA_BIST		0
+
+#define KORINA_CNFG3 ((KORINA_BIST << 24) | \
+		      (KORINA_HEADER_TYPE<<16) | \
+		      (KORINA_MASTER_LAT<<8) | \
+		      KORINA_CACHE_LINE_SIZE)
+
+#define KORINA_BAR0	0x00000008	/* 128 MB Memory */
+#define KORINA_BAR1	0x18800001	/* 1 MB IO */
+#define KORINA_BAR2	0x18000001	/* 2 MB IO window for Korina
+					   internal Registers */
+#define KORINA_BAR3	0x48000008	/* Spare 128 MB Memory */
+
+#define KORINA_CNFG4	KORINA_BAR0
+#define KORINA_CNFG5	KORINA_BAR1
+#define KORINA_CNFG6	KORINA_BAR2
+#define KORINA_CNFG7	KORINA_BAR3
+
+#define KORINA_SUBSYS_VENDOR_ID 0x011d
+#define KORINA_SUBSYSTEM_ID	0x0214
+#define KORINA_CNFG8		0
+#define KORINA_CNFG9		0
+#define KORINA_CNFG10		0
+#define KORINA_CNFG11	((KORINA_SUBSYS_VENDOR_ID<<16) | \
+			  KORINA_SUBSYSTEM_ID)
+#define KORINA_INT_LINE		1
+#define KORINA_INT_PIN		1
+#define KORINA_MIN_GNT		8
+#define KORINA_MAX_LAT		0x38
+#define KORINA_CNFG12		0
+#define KORINA_CNFG13		0
+#define KORINA_CNFG14		0
+#define KORINA_CNFG15	((KORINA_MAX_LAT<<24) | \
+			 (KORINA_MIN_GNT<<16) | \
+			 (KORINA_INT_PIN<<8)  | \
+			  KORINA_INT_LINE)
+#define KORINA_RETRY_LIMIT	0x80
+#define KORINA_TRDY_LIMIT	0x80
+#define KORINA_CNFG16 ((KORINA_RETRY_LIMIT<<8) | \
+			KORINA_TRDY_LIMIT)
+#define PCI_PBAxC_R		0x0
+#define PCI_PBAxC_RL		0x1
+#define PCI_PBAxC_RM		0x2
+#define SIZE_SHFT		2
+
+#if defined(__MIPSEB__)
+#define KORINA_PBA0C	(PCI_PBAC_MRL | PCI_PBAC_SB | \
+			  ((PCI_PBAxC_RM & 0x3) << PCI_PBAC_MR_BIT) | \
+			  PCI_PBAC_PP | \
+			  (SIZE_128MB<<SIZE_SHFT) | \
+			   PCI_PBAC_P)
+#else
+#define KORINA_PBA0C	(PCI_PBAC_MRL | \
+			  ((PCI_PBAxC_RM & 0x3) << PCI_PBAC_MR_BIT) | \
+			  PCI_PBAC_PP | \
+			  (SIZE_128MB<<SIZE_SHFT) | \
+			   PCI_PBAC_P)
+#endif
+#define KORINA_CNFG17	KORINA_PBA0C
+#define KORINA_PBA0M	0x0
+#define KORINA_CNFG18	KORINA_PBA0M
+
+#if defined(__MIPSEB__)
+#define KORINA_PBA1C	((SIZE_1MB<<SIZE_SHFT) | PCI_PBAC_SB | \
+			  PCI_PBAC_MSI)
+#else
+#define KORINA_PBA1C	((SIZE_1MB<<SIZE_SHFT) | \
+			  PCI_PBAC_MSI)
+#endif
+#define KORINA_CNFG19	KORINA_PBA1C
+#define KORINA_PBA1M	0x0
+#define KORINA_CNFG20	KORINA_PBA1M
+
+#if defined(__MIPSEB__)
+#define KORINA_PBA2C	((SIZE_2MB<<SIZE_SHFT) | PCI_PBAC_SB | \
+			  PCI_PBAC_MSI)
+#else
+#define KORINA_PBA2C	((SIZE_2MB<<SIZE_SHFT) | \
+			  PCI_PBAC_MSI)
+#endif
+#define KORINA_CNFG21	KORINA_PBA2C
+#define KORINA_PBA2M	0x18000000
+#define KORINA_CNFG22	KORINA_PBA2M
+#define KORINA_PBA3C	0
+#define KORINA_CNFG23	KORINA_PBA3C
+#define KORINA_PBA3M	0
+#define KORINA_CNFG24	KORINA_PBA3M
+
+#define PCITC_DTIMER_VAL	8
+#define PCITC_RTIMER_VAL	0x10
+
+#endif	/* __ASM_RC32434_PCI_H */
diff --git a/arch/mips/include/asm/mach-rc32434/prom.h b/arch/mips/include/asm/mach-rc32434/prom.h
new file mode 100644
index 000000000..660707f1b
--- /dev/null
+++ b/arch/mips/include/asm/mach-rc32434/prom.h
@@ -0,0 +1,40 @@
+/*
+ *  Definitions for the PROM
+ *
+ *  Copyright 2002 Ryan Holm <ryan.holmQVist@idt.com>
+ *  Copyright 2008 Florian Fainelli <florian@openwrt.org>
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ */
+
+#define PROM_ENTRY(x)		(0xbfc00000 + ((x) * 8))
+
+#define SR_NMI			0x00180000
+#define SERIAL_SPEED_ENTRY	0x00000001
+
+#define FREQ_TAG		"HZ="
+#define KMAC_TAG		"kmac="
+#define MEM_TAG			"mem="
+#define BOARD_TAG		"board="
+
+#define BOARD_RB532		"500"
+#define BOARD_RB532A		"500r5"
diff --git a/arch/mips/include/asm/mach-rc32434/rb.h b/arch/mips/include/asm/mach-rc32434/rb.h
new file mode 100644
index 000000000..dd9d4b026
--- /dev/null
+++ b/arch/mips/include/asm/mach-rc32434/rb.h
@@ -0,0 +1,64 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ *
+ *  Copyright (C) 2004 IDT Inc.
+ *  Copyright (C) 2006 Felix Fietkau <nbd@openwrt.org>
+ */
+#ifndef __ASM_RC32434_RB_H
+#define __ASM_RC32434_RB_H
+
+#define REGBASE		0x18000000
+#define IDT434_REG_BASE ((volatile void *) KSEG1ADDR(REGBASE))
+#define UART0BASE	0x58000
+#define RST		(1 << 15)
+#define DEV0BASE	0x010000
+#define DEV0MASK	0x010004
+#define DEV0C		0x010008
+#define DEV0T		0x01000C
+#define DEV1BASE	0x010010
+#define DEV1MASK	0x010014
+#define DEV1C		0x010018
+#define DEV1TC		0x01001C
+#define DEV2BASE	0x010020
+#define DEV2MASK	0x010024
+#define DEV2C		0x010028
+#define DEV2TC		0x01002C
+#define DEV3BASE	0x010030
+#define DEV3MASK	0x010034
+#define DEV3C		0x010038
+#define DEV3TC		0x01003C
+#define BTCS		0x010040
+#define BTCOMPARE	0x010044
+#define LO_WPX		(1 << 0)
+#define LO_ALE		(1 << 1)
+#define LO_CLE		(1 << 2)
+#define LO_CEX		(1 << 3)
+#define LO_FOFF		(1 << 5)
+#define LO_SPICS	(1 << 6)
+#define LO_ULED		(1 << 7)
+
+#define BIT_TO_MASK(x)	(1 << x)
+
+struct dev_reg {
+	u32	base;
+	u32	mask;
+	u32	ctl;
+	u32	timing;
+};
+
+struct korina_device {
+	char *name;
+	unsigned char mac[6];
+	struct net_device *dev;
+};
+
+struct mpmc_device {
+	unsigned char	state;
+	spinlock_t	lock;
+	void __iomem	*base;
+};
+
+extern void set_latch_u5(unsigned char or_mask, unsigned char nand_mask);
+extern unsigned char get_latch_u5(void);
+
+#endif	/* __ASM_RC32434_RB_H */
diff --git a/arch/mips/include/asm/mach-rc32434/rc32434.h b/arch/mips/include/asm/mach-rc32434/rc32434.h
new file mode 100644
index 000000000..1bec6cc8a
--- /dev/null
+++ b/arch/mips/include/asm/mach-rc32434/rc32434.h
@@ -0,0 +1,20 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Definitions for IDT RC323434 CPU.
+ */
+
+#ifndef _ASM_RC32434_RC32434_H_
+#define _ASM_RC32434_RC32434_H_
+
+#include <linux/delay.h>
+#include <linux/io.h>
+
+#define IDT_CLOCK_MULT		2
+
+/* cpu pipeline flush */
+static inline void rc32434_sync(void)
+{
+	__asm__ volatile ("sync");
+}
+
+#endif	/* _ASM_RC32434_RC32434_H_ */
diff --git a/arch/mips/include/asm/mach-rc32434/timer.h b/arch/mips/include/asm/mach-rc32434/timer.h
new file mode 100644
index 000000000..cda26bb9e
--- /dev/null
+++ b/arch/mips/include/asm/mach-rc32434/timer.h
@@ -0,0 +1,65 @@
+/*
+ *  Definitions for timer registers
+ *
+ *  Copyright 2004 Philip Rischel <rischelp@idt.com>
+ *  Copyright 2008 Florian Fainelli <florian@openwrt.org>
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ */
+
+#ifndef __ASM_RC32434_TIMER_H
+#define __ASM_RC32434_TIMER_H
+
+#include <asm/mach-rc32434/rb.h>
+
+#define TIMER0_BASE_ADDR		0x18028000
+#define TIMER_COUNT			3
+
+struct timer_counter {
+	u32 count;
+	u32 compare;
+	u32 ctc;		/*use CTC_ */
+};
+
+struct timer {
+	struct timer_counter tim[TIMER_COUNT];
+	u32 rcount;	/* use RCOUNT_ */
+	u32 rcompare;	/* use RCOMPARE_ */
+	u32 rtc;	/* use RTC_ */
+};
+
+#define RC32434_CTC_EN_BIT		0
+#define RC32434_CTC_TO_BIT		1
+
+/* Real time clock registers */
+#define RC32434_RTC_MSK(x)		BIT_TO_MASK(x)
+#define RC32434_RTC_CE_BIT		0
+#define RC32434_RTC_TO_BIT		1
+#define RC32434_RTC_RQE_BIT		2
+
+/* Counter registers */
+#define RC32434_RCOUNT_BIT		0
+#define RC32434_RCOUNT_MSK		0x0000ffff
+#define RC32434_RCOMP_BIT		0
+#define RC32434_RCOMP_MSK		0x0000ffff
+
+#endif	/* __ASM_RC32434_TIMER_H */
diff --git a/arch/mips/include/asm/mach-rm/cpu-feature-overrides.h b/arch/mips/include/asm/mach-rm/cpu-feature-overrides.h
new file mode 100644
index 000000000..e1e182300
--- /dev/null
+++ b/arch/mips/include/asm/mach-rm/cpu-feature-overrides.h
@@ -0,0 +1,42 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003, 04, 07 Ralf Baechle (ralf@linux-mips.org)
+ *
+ * SNI RM200 C apparently was only shipped with R4600 V2.0 and R5000 processors.
+ */
+#ifndef __ASM_MACH_RM200_CPU_FEATURE_OVERRIDES_H
+#define __ASM_MACH_RM200_CPU_FEATURE_OVERRIDES_H
+
+#define cpu_has_tlb		1
+#define cpu_has_4kex		1
+#define cpu_has_4k_cache	1
+#define cpu_has_32fpr		1
+#define cpu_has_counter		1
+#define cpu_has_watch		0
+#define cpu_has_mips16		0
+#define cpu_has_mips16e2	0
+#define cpu_has_divec		0
+#define cpu_has_cache_cdex_p	1
+#define cpu_has_prefetch	0
+#define cpu_has_mcheck		0
+#define cpu_has_ejtag		0
+#define cpu_has_llsc		1
+#define cpu_has_vtag_icache	0
+#define cpu_has_dc_aliases	(PAGE_SIZE < 0x4000)
+#define cpu_has_ic_fills_f_dc	0
+#define cpu_has_dsp		0
+#define cpu_has_dsp2		0
+#define cpu_has_nofpuex		0
+#define cpu_has_64bits		1
+#define cpu_has_mipsmt		0
+#define cpu_has_userlocal	0
+
+#define cpu_has_mips32r1	0
+#define cpu_has_mips32r2	0
+#define cpu_has_mips64r1	0
+#define cpu_has_mips64r2	0
+
+#endif /* __ASM_MACH_RM200_CPU_FEATURE_OVERRIDES_H */
diff --git a/arch/mips/include/asm/mach-rm/mc146818rtc.h b/arch/mips/include/asm/mach-rm/mc146818rtc.h
new file mode 100644
index 000000000..a074f4f84
--- /dev/null
+++ b/arch/mips/include/asm/mach-rm/mc146818rtc.h
@@ -0,0 +1,21 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2004 by Ralf Baechle
+ *
+ * RTC routines for PC style attached Dallas chip with ARC epoch.
+ */
+#ifndef __ASM_MACH_RM_MC146818RTC_H
+#define __ASM_MACH_RM_MC146818RTC_H
+
+#ifdef CONFIG_CPU_BIG_ENDIAN
+#define mc146818_decode_year(year) ((year) < 70 ? (year) + 2000 : (year) + 1900)
+#else
+#define mc146818_decode_year(year) ((year) + 1980)
+#endif
+
+#include <asm/mach-generic/mc146818rtc.h>
+
+#endif /* __ASM_MACH_RM_MC146818RTC_H */
diff --git a/arch/mips/include/asm/mach-sibyte/cpu-feature-overrides.h b/arch/mips/include/asm/mach-sibyte/cpu-feature-overrides.h
new file mode 100644
index 000000000..702235805
--- /dev/null
+++ b/arch/mips/include/asm/mach-sibyte/cpu-feature-overrides.h
@@ -0,0 +1,49 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003, 04, 07 Ralf Baechle (ralf@linux-mips.org)
+ */
+#ifndef __ASM_MACH_SIBYTE_CPU_FEATURE_OVERRIDES_H
+#define __ASM_MACH_SIBYTE_CPU_FEATURE_OVERRIDES_H
+
+/*
+ * Sibyte are MIPS64 processors wired to a specific configuration
+ */
+#define cpu_has_watch		1
+#define cpu_has_mips16		0
+#define cpu_has_mips16e2	0
+#define cpu_has_divec		1
+#define cpu_has_vce		0
+#define cpu_has_cache_cdex_p	0
+#define cpu_has_cache_cdex_s	0
+#define cpu_has_prefetch	1
+#define cpu_has_mcheck		1
+#define cpu_has_ejtag		1
+
+#define cpu_has_llsc		1
+#define cpu_has_vtag_icache	1
+#define cpu_has_dc_aliases	0
+#define cpu_has_ic_fills_f_dc	0
+#define cpu_has_dsp		0
+#define cpu_has_dsp2		0
+#define cpu_has_mipsmt		0
+#define cpu_has_userlocal	0
+#define cpu_icache_snoops_remote_store	0
+
+#define cpu_has_nofpuex		0
+#define cpu_has_64bits		1
+
+#define cpu_has_mips32r1	1
+#define cpu_has_mips32r2	0
+#define cpu_has_mips64r1	1
+#define cpu_has_mips64r2	0
+
+#define cpu_has_inclusive_pcaches	0
+
+#define cpu_dcache_line_size()	32
+#define cpu_icache_line_size()	32
+#define cpu_scache_line_size()	32
+
+#endif /* __ASM_MACH_SIBYTE_CPU_FEATURE_OVERRIDES_H */
diff --git a/arch/mips/include/asm/mach-tx49xx/cpu-feature-overrides.h b/arch/mips/include/asm/mach-tx49xx/cpu-feature-overrides.h
new file mode 100644
index 000000000..04e424725
--- /dev/null
+++ b/arch/mips/include/asm/mach-tx49xx/cpu-feature-overrides.h
@@ -0,0 +1,26 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_MACH_TX49XX_CPU_FEATURE_OVERRIDES_H
+#define __ASM_MACH_TX49XX_CPU_FEATURE_OVERRIDES_H
+
+#define cpu_has_llsc	1
+#define cpu_has_64bits	1
+#define cpu_has_inclusive_pcaches	0
+
+#define cpu_has_mips16		0
+#define cpu_has_mips16e2	0
+#define cpu_has_mdmx		0
+#define cpu_has_mips3d		0
+#define cpu_has_smartmips	0
+#define cpu_has_vtag_icache	0
+#define cpu_has_ic_fills_f_dc	0
+#define cpu_has_dsp	0
+#define cpu_has_dsp2		0
+#define cpu_has_mipsmt	0
+#define cpu_has_userlocal	0
+
+#define cpu_has_mips32r1	0
+#define cpu_has_mips32r2	0
+#define cpu_has_mips64r1	0
+#define cpu_has_mips64r2	0
+
+#endif /* __ASM_MACH_TX49XX_CPU_FEATURE_OVERRIDES_H */
diff --git a/arch/mips/include/asm/mach-tx49xx/ioremap.h b/arch/mips/include/asm/mach-tx49xx/ioremap.h
new file mode 100644
index 000000000..b1f3710ac
--- /dev/null
+++ b/arch/mips/include/asm/mach-tx49xx/ioremap.h
@@ -0,0 +1,30 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ *	include/asm-mips/mach-tx49xx/ioremap.h
+ */
+#ifndef __ASM_MACH_TX49XX_IOREMAP_H
+#define __ASM_MACH_TX49XX_IOREMAP_H
+
+#include <linux/types.h>
+
+static inline void __iomem *plat_ioremap(phys_addr_t offset, unsigned long size,
+	unsigned long flags)
+{
+#ifdef CONFIG_64BIT
+#define TXX9_DIRECTMAP_BASE	0xfff000000ul
+#else
+#define TXX9_DIRECTMAP_BASE	0xff000000ul
+#endif
+	if (offset >= TXX9_DIRECTMAP_BASE &&
+	    offset < TXX9_DIRECTMAP_BASE + 0x400000)
+		return (void __iomem *)(unsigned long)(int)offset;
+	return NULL;
+}
+
+static inline int plat_iounmap(const volatile void __iomem *addr)
+{
+	return (unsigned long)addr >=
+		(unsigned long)(int)(TXX9_DIRECTMAP_BASE & 0xffffffff);
+}
+
+#endif /* __ASM_MACH_TX49XX_IOREMAP_H */
diff --git a/arch/mips/include/asm/mach-tx49xx/kmalloc.h b/arch/mips/include/asm/mach-tx49xx/kmalloc.h
new file mode 100644
index 000000000..c2a0a6fa4
--- /dev/null
+++ b/arch/mips/include/asm/mach-tx49xx/kmalloc.h
@@ -0,0 +1,7 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_MACH_TX49XX_KMALLOC_H
+#define __ASM_MACH_TX49XX_KMALLOC_H
+
+#define ARCH_DMA_MINALIGN L1_CACHE_BYTES
+
+#endif /* __ASM_MACH_TX49XX_KMALLOC_H */
diff --git a/arch/mips/include/asm/mach-tx49xx/mangle-port.h b/arch/mips/include/asm/mach-tx49xx/mangle-port.h
new file mode 100644
index 000000000..50b1b8f1e
--- /dev/null
+++ b/arch/mips/include/asm/mach-tx49xx/mangle-port.h
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_MACH_TX49XX_MANGLE_PORT_H
+#define __ASM_MACH_TX49XX_MANGLE_PORT_H
+
+#define __swizzle_addr_b(port)	(port)
+#define __swizzle_addr_w(port)	(port)
+#define __swizzle_addr_l(port)	(port)
+#define __swizzle_addr_q(port)	(port)
+
+#define ioswabb(a, x)		(x)
+#define __mem_ioswabb(a, x)	(x)
+#define ioswabw(a, x)		le16_to_cpu((__force __le16)(x))
+#define __mem_ioswabw(a, x)	(x)
+#define ioswabl(a, x)		le32_to_cpu((__force __le32)(x))
+#define __mem_ioswabl(a, x)	(x)
+#define ioswabq(a, x)		le64_to_cpu((__force __le64)(x))
+#define __mem_ioswabq(a, x)	(x)
+
+#endif /* __ASM_MACH_TX49XX_MANGLE_PORT_H */
diff --git a/arch/mips/include/asm/mach-tx49xx/spaces.h b/arch/mips/include/asm/mach-tx49xx/spaces.h
new file mode 100644
index 000000000..0cb10a6f4
--- /dev/null
+++ b/arch/mips/include/asm/mach-tx49xx/spaces.h
@@ -0,0 +1,17 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994 - 1999, 2000, 03, 04 Ralf Baechle
+ * Copyright (C) 2000, 2002  Maciej W. Rozycki
+ * Copyright (C) 1990, 1999, 2000 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_TX49XX_SPACES_H
+#define _ASM_TX49XX_SPACES_H
+
+#define FIXADDR_TOP		((unsigned long)(long)(int)0xfefe0000)
+
+#include <asm/mach-generic/spaces.h>
+
+#endif /* __ASM_TX49XX_SPACES_H */
diff --git a/arch/mips/include/asm/machine.h b/arch/mips/include/asm/machine.h
new file mode 100644
index 000000000..fc64cce27
--- /dev/null
+++ b/arch/mips/include/asm/machine.h
@@ -0,0 +1,90 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2016 Imagination Technologies
+ * Author: Paul Burton <paul.burton@mips.com>
+ */
+
+#ifndef __MIPS_ASM_MACHINE_H__
+#define __MIPS_ASM_MACHINE_H__
+
+#include <linux/libfdt.h>
+#include <linux/of.h>
+
+struct mips_machine {
+	const struct of_device_id *matches;
+	const void *fdt;
+	bool (*detect)(void);
+	const void *(*fixup_fdt)(const void *fdt, const void *match_data);
+	unsigned int (*measure_hpt_freq)(void);
+};
+
+extern long __mips_machines_start;
+extern long __mips_machines_end;
+
+#define MIPS_MACHINE(name)						\
+	static const struct mips_machine __mips_mach_##name		\
+		__used __section(".mips.machines.init")
+
+#define for_each_mips_machine(mach)					\
+	for ((mach) = (struct mips_machine *)&__mips_machines_start;	\
+	     (mach) < (struct mips_machine *)&__mips_machines_end;	\
+	     (mach)++)
+
+/**
+ * mips_machine_is_compatible() - check if a machine is compatible with an FDT
+ * @mach: the machine struct to check
+ * @fdt: the FDT to check for compatibility with
+ *
+ * Check whether the given machine @mach is compatible with the given flattened
+ * device tree @fdt, based upon the compatibility property of the root node.
+ *
+ * Return: the device id matched if any, else NULL
+ */
+static inline const struct of_device_id *
+mips_machine_is_compatible(const struct mips_machine *mach, const void *fdt)
+{
+	const struct of_device_id *match;
+
+	if (!mach->matches)
+		return NULL;
+
+	for (match = mach->matches; match->compatible[0]; match++) {
+		if (fdt_node_check_compatible(fdt, 0, match->compatible) == 0)
+			return match;
+	}
+
+	return NULL;
+}
+
+/**
+ * struct mips_fdt_fixup - Describe a fixup to apply to an FDT
+ * @apply: applies the fixup to @fdt, returns zero on success else -errno
+ * @description: a short description of the fixup
+ *
+ * Describes a fixup applied to an FDT blob by the @apply function. The
+ * @description field provides a short description of the fixup intended for
+ * use in error messages if the @apply function returns non-zero.
+ */
+struct mips_fdt_fixup {
+	int (*apply)(void *fdt);
+	const char *description;
+};
+
+/**
+ * apply_mips_fdt_fixups() - apply fixups to an FDT blob
+ * @fdt_out: buffer in which to place the fixed-up FDT
+ * @fdt_out_size: the size of the @fdt_out buffer
+ * @fdt_in: the FDT blob
+ * @fixups: pointer to an array of fixups to be applied
+ *
+ * Loop through the array of fixups pointed to by @fixups, calling the apply
+ * function on each until either one returns an error or we reach the end of
+ * the list as indicated by an entry with a NULL apply field.
+ *
+ * Return: zero on success, else -errno
+ */
+extern int __init apply_mips_fdt_fixups(void *fdt_out, size_t fdt_out_size,
+					const void *fdt_in,
+					const struct mips_fdt_fixup *fixups);
+
+#endif /* __MIPS_ASM_MACHINE_H__ */
diff --git a/arch/mips/include/asm/mc146818-time.h b/arch/mips/include/asm/mc146818-time.h
new file mode 100644
index 000000000..cbf5cec34
--- /dev/null
+++ b/arch/mips/include/asm/mc146818-time.h
@@ -0,0 +1,119 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Machine dependent access functions for RTC registers.
+ */
+#ifndef __ASM_MC146818_TIME_H
+#define __ASM_MC146818_TIME_H
+
+#include <linux/bcd.h>
+#include <linux/mc146818rtc.h>
+#include <linux/time.h>
+
+/*
+ * For check timing call set_rtc_mmss() 500ms; used in timer interrupt.
+ */
+#define USEC_AFTER	500000
+#define USEC_BEFORE	500000
+
+/*
+ * In order to set the CMOS clock precisely, set_rtc_mmss has to be
+ * called 500 ms after the second nowtime has started, because when
+ * nowtime is written into the registers of the CMOS clock, it will
+ * jump to the next second precisely 500 ms later. Check the Motorola
+ * MC146818A or Dallas DS12887 data sheet for details.
+ *
+ * BUG: This routine does not handle hour overflow properly; it just
+ *	sets the minutes. Usually you'll only notice that after reboot!
+ */
+static inline int mc146818_set_rtc_mmss(unsigned long nowtime)
+{
+	int real_seconds, real_minutes, cmos_minutes;
+	unsigned char save_control, save_freq_select;
+	int retval = 0;
+	unsigned long flags;
+
+	spin_lock_irqsave(&rtc_lock, flags);
+	save_control = CMOS_READ(RTC_CONTROL); /* tell the clock it's being set */
+	CMOS_WRITE((save_control|RTC_SET), RTC_CONTROL);
+
+	save_freq_select = CMOS_READ(RTC_FREQ_SELECT); /* stop and reset prescaler */
+	CMOS_WRITE((save_freq_select|RTC_DIV_RESET2), RTC_FREQ_SELECT);
+
+	cmos_minutes = CMOS_READ(RTC_MINUTES);
+	if (!(save_control & RTC_DM_BINARY) || RTC_ALWAYS_BCD)
+		cmos_minutes = bcd2bin(cmos_minutes);
+
+	/*
+	 * since we're only adjusting minutes and seconds,
+	 * don't interfere with hour overflow. This avoids
+	 * messing with unknown time zones but requires your
+	 * RTC not to be off by more than 15 minutes
+	 */
+	real_seconds = nowtime % 60;
+	real_minutes = nowtime / 60;
+	if (((abs(real_minutes - cmos_minutes) + 15)/30) & 1)
+		real_minutes += 30;		/* correct for half hour time zone */
+	real_minutes %= 60;
+
+	if (abs(real_minutes - cmos_minutes) < 30) {
+		if (!(save_control & RTC_DM_BINARY) || RTC_ALWAYS_BCD) {
+			real_seconds = bin2bcd(real_seconds);
+			real_minutes = bin2bcd(real_minutes);
+		}
+		CMOS_WRITE(real_seconds, RTC_SECONDS);
+		CMOS_WRITE(real_minutes, RTC_MINUTES);
+	} else {
+		printk_once(KERN_NOTICE
+		       "set_rtc_mmss: can't update from %d to %d\n",
+		       cmos_minutes, real_minutes);
+		retval = -1;
+	}
+
+	/* The following flags have to be released exactly in this order,
+	 * otherwise the DS12887 (popular MC146818A clone with integrated
+	 * battery and quartz) will not reset the oscillator and will not
+	 * update precisely 500 ms later. You won't find this mentioned in
+	 * the Dallas Semiconductor data sheets, but who believes data
+	 * sheets anyway ...			       -- Markus Kuhn
+	 */
+	CMOS_WRITE(save_control, RTC_CONTROL);
+	CMOS_WRITE(save_freq_select, RTC_FREQ_SELECT);
+	spin_unlock_irqrestore(&rtc_lock, flags);
+
+	return retval;
+}
+
+static inline time64_t mc146818_get_cmos_time(void)
+{
+	unsigned int year, mon, day, hour, min, sec;
+	unsigned long flags;
+
+	spin_lock_irqsave(&rtc_lock, flags);
+
+	do {
+		sec = CMOS_READ(RTC_SECONDS);
+		min = CMOS_READ(RTC_MINUTES);
+		hour = CMOS_READ(RTC_HOURS);
+		day = CMOS_READ(RTC_DAY_OF_MONTH);
+		mon = CMOS_READ(RTC_MONTH);
+		year = CMOS_READ(RTC_YEAR);
+	} while (sec != CMOS_READ(RTC_SECONDS));
+
+	if (!(CMOS_READ(RTC_CONTROL) & RTC_DM_BINARY) || RTC_ALWAYS_BCD) {
+		sec = bcd2bin(sec);
+		min = bcd2bin(min);
+		hour = bcd2bin(hour);
+		day = bcd2bin(day);
+		mon = bcd2bin(mon);
+		year = bcd2bin(year);
+	}
+	spin_unlock_irqrestore(&rtc_lock, flags);
+	year = mc146818_decode_year(year);
+
+	return mktime64(year, mon, day, hour, min, sec);
+}
+
+#endif /* __ASM_MC146818_TIME_H */
diff --git a/arch/mips/include/asm/mc146818rtc.h b/arch/mips/include/asm/mc146818rtc.h
new file mode 100644
index 000000000..68b4da6d5
--- /dev/null
+++ b/arch/mips/include/asm/mc146818rtc.h
@@ -0,0 +1,16 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Machine dependent access functions for RTC registers.
+ *
+ * Copyright (C) 1996, 1997, 1998, 2000 Ralf Baechle
+ * Copyright (C) 2002  Maciej W. Rozycki
+ */
+#ifndef _ASM_MC146818RTC_H
+#define _ASM_MC146818RTC_H
+
+#include <mc146818rtc.h>
+
+#endif /* _ASM_MC146818RTC_H */
diff --git a/arch/mips/include/asm/mips-boards/bonito64.h b/arch/mips/include/asm/mips-boards/bonito64.h
new file mode 100644
index 000000000..5368891d4
--- /dev/null
+++ b/arch/mips/include/asm/mips-boards/bonito64.h
@@ -0,0 +1,430 @@
+/*
+ * Bonito Register Map
+ *
+ * This file is the original bonito.h from Algorithmics with minor changes
+ * to fit into linux.
+ *
+ * Copyright (c) 1999 Algorithmics Ltd
+ *
+ * Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 2001 MIPS Technologies, Inc.  All rights reserved.
+ *
+ * Algorithmics gives permission for anyone to use and modify this file
+ * without any obligation or license condition except that you retain
+ * this copyright message in any source redistribution in whole or part.
+ *
+ */
+
+/* Revision 1.48 autogenerated on 08/17/99 15:20:01 */
+/* This bonito64 version editted from bonito.h Revision 1.48 on 11/09/00 */
+
+#ifndef _ASM_MIPS_BOARDS_BONITO64_H
+#define _ASM_MIPS_BOARDS_BONITO64_H
+
+#ifdef __ASSEMBLY__
+
+/* offsets from base register */
+#define BONITO(x)	(x)
+
+#else
+
+/*
+ * Algorithmics Bonito64 system controller register base.
+ */
+extern unsigned long _pcictrl_bonito;
+extern unsigned long _pcictrl_bonito_pcicfg;
+
+#define BONITO(x)		*(volatile u32 *)(_pcictrl_bonito + (x))
+
+#endif /* __ASSEMBLY__ */
+
+
+#define BONITO_BOOT_BASE		0x1fc00000
+#define BONITO_BOOT_SIZE		0x00100000
+#define BONITO_BOOT_TOP			(BONITO_BOOT_BASE+BONITO_BOOT_SIZE-1)
+#define BONITO_FLASH_BASE		0x1c000000
+#define BONITO_FLASH_SIZE		0x03000000
+#define BONITO_FLASH_TOP		(BONITO_FLASH_BASE+BONITO_FLASH_SIZE-1)
+#define BONITO_SOCKET_BASE		0x1f800000
+#define BONITO_SOCKET_SIZE		0x00400000
+#define BONITO_SOCKET_TOP		(BONITO_SOCKET_BASE+BONITO_SOCKET_SIZE-1)
+#define BONITO_REG_BASE			0x1fe00000
+#define BONITO_REG_SIZE			0x00040000
+#define BONITO_REG_TOP			(BONITO_REG_BASE+BONITO_REG_SIZE-1)
+#define BONITO_DEV_BASE			0x1ff00000
+#define BONITO_DEV_SIZE			0x00100000
+#define BONITO_DEV_TOP			(BONITO_DEV_BASE+BONITO_DEV_SIZE-1)
+#define BONITO_PCILO_BASE		0x10000000
+#define BONITO_PCILO_SIZE		0x0c000000
+#define BONITO_PCILO_TOP		(BONITO_PCILO_BASE+BONITO_PCILO_SIZE-1)
+#define BONITO_PCILO0_BASE		0x10000000
+#define BONITO_PCILO1_BASE		0x14000000
+#define BONITO_PCILO2_BASE		0x18000000
+#define BONITO_PCIHI_BASE		0x20000000
+#define BONITO_PCIHI_SIZE		0x20000000
+#define BONITO_PCIHI_TOP		(BONITO_PCIHI_BASE+BONITO_PCIHI_SIZE-1)
+#define BONITO_PCIIO_BASE		0x1fd00000
+#define BONITO_PCIIO_SIZE		0x00100000
+#define BONITO_PCIIO_TOP		(BONITO_PCIIO_BASE+BONITO_PCIIO_SIZE-1)
+#define BONITO_PCICFG_BASE		0x1fe80000
+#define BONITO_PCICFG_SIZE		0x00080000
+#define BONITO_PCICFG_TOP		(BONITO_PCICFG_BASE+BONITO_PCICFG_SIZE-1)
+
+
+/* Bonito Register Bases */
+
+#define BONITO_PCICONFIGBASE		0x00
+#define BONITO_REGBASE			0x100
+
+
+/* PCI Configuration  Registers */
+
+#define BONITO_PCI_REG(x)		BONITO(BONITO_PCICONFIGBASE + (x))
+#define BONITO_PCIDID			BONITO_PCI_REG(0x00)
+#define BONITO_PCICMD			BONITO_PCI_REG(0x04)
+#define BONITO_PCICLASS			BONITO_PCI_REG(0x08)
+#define BONITO_PCILTIMER		BONITO_PCI_REG(0x0c)
+#define BONITO_PCIBASE0			BONITO_PCI_REG(0x10)
+#define BONITO_PCIBASE1			BONITO_PCI_REG(0x14)
+#define BONITO_PCIBASE2			BONITO_PCI_REG(0x18)
+#define BONITO_PCIEXPRBASE		BONITO_PCI_REG(0x30)
+#define BONITO_PCIINT			BONITO_PCI_REG(0x3c)
+
+#define BONITO_PCICMD_PERR_CLR		0x80000000
+#define BONITO_PCICMD_SERR_CLR		0x40000000
+#define BONITO_PCICMD_MABORT_CLR	0x20000000
+#define BONITO_PCICMD_MTABORT_CLR	0x10000000
+#define BONITO_PCICMD_TABORT_CLR	0x08000000
+#define BONITO_PCICMD_MPERR_CLR		0x01000000
+#define BONITO_PCICMD_PERRRESPEN	0x00000040
+#define BONITO_PCICMD_ASTEPEN		0x00000080
+#define BONITO_PCICMD_SERREN		0x00000100
+#define BONITO_PCILTIMER_BUSLATENCY	0x0000ff00
+#define BONITO_PCILTIMER_BUSLATENCY_SHIFT	8
+
+
+
+
+/* 1. Bonito h/w Configuration */
+/* Power on register */
+
+#define BONITO_BONPONCFG		BONITO(BONITO_REGBASE + 0x00)
+
+#define BONITO_BONPONCFG_SYSCONTROLLERRD	0x00040000
+#define BONITO_BONPONCFG_ROMCS1SAMP	0x00020000
+#define BONITO_BONPONCFG_ROMCS0SAMP	0x00010000
+#define BONITO_BONPONCFG_CPUBIGEND	0x00004000
+/* Added by RPF 11-9-00 */
+#define BONITO_BONPONCFG_BURSTORDER	0x00001000
+/* --- */
+#define BONITO_BONPONCFG_CPUPARITY	0x00002000
+#define BONITO_BONPONCFG_CPUTYPE	0x00000007
+#define BONITO_BONPONCFG_CPUTYPE_SHIFT	0
+#define BONITO_BONPONCFG_PCIRESET_OUT	0x00000008
+#define BONITO_BONPONCFG_IS_ARBITER	0x00000010
+#define BONITO_BONPONCFG_ROMBOOT	0x000000c0
+#define BONITO_BONPONCFG_ROMBOOT_SHIFT	6
+
+#define BONITO_BONPONCFG_ROMBOOT_FLASH	(0x0<<BONITO_BONPONCFG_ROMBOOT_SHIFT)
+#define BONITO_BONPONCFG_ROMBOOT_SOCKET (0x1<<BONITO_BONPONCFG_ROMBOOT_SHIFT)
+#define BONITO_BONPONCFG_ROMBOOT_SDRAM	(0x2<<BONITO_BONPONCFG_ROMBOOT_SHIFT)
+#define BONITO_BONPONCFG_ROMBOOT_CPURESET	(0x3<<BONITO_BONPONCFG_ROMBOOT_SHIFT)
+
+#define BONITO_BONPONCFG_ROMCS0WIDTH	0x00000100
+#define BONITO_BONPONCFG_ROMCS1WIDTH	0x00000200
+#define BONITO_BONPONCFG_ROMCS0FAST	0x00000400
+#define BONITO_BONPONCFG_ROMCS1FAST	0x00000800
+#define BONITO_BONPONCFG_CONFIG_DIS	0x00000020
+
+
+/* Other Bonito configuration */
+
+#define BONITO_BONGENCFG_OFFSET		0x4
+#define BONITO_BONGENCFG		BONITO(BONITO_REGBASE + BONITO_BONGENCFG_OFFSET)
+
+#define BONITO_BONGENCFG_DEBUGMODE	0x00000001
+#define BONITO_BONGENCFG_SNOOPEN	0x00000002
+#define BONITO_BONGENCFG_CPUSELFRESET	0x00000004
+
+#define BONITO_BONGENCFG_FORCE_IRQA	0x00000008
+#define BONITO_BONGENCFG_IRQA_ISOUT	0x00000010
+#define BONITO_BONGENCFG_IRQA_FROM_INT1 0x00000020
+#define BONITO_BONGENCFG_BYTESWAP	0x00000040
+
+#define BONITO_BONGENCFG_UNCACHED	0x00000080
+#define BONITO_BONGENCFG_PREFETCHEN	0x00000100
+#define BONITO_BONGENCFG_WBEHINDEN	0x00000200
+#define BONITO_BONGENCFG_CACHEALG	0x00000c00
+#define BONITO_BONGENCFG_CACHEALG_SHIFT 10
+#define BONITO_BONGENCFG_PCIQUEUE	0x00001000
+#define BONITO_BONGENCFG_CACHESTOP	0x00002000
+#define BONITO_BONGENCFG_MSTRBYTESWAP	0x00004000
+#define BONITO_BONGENCFG_BUSERREN	0x00008000
+#define BONITO_BONGENCFG_NORETRYTIMEOUT 0x00010000
+#define BONITO_BONGENCFG_SHORTCOPYTIMEOUT	0x00020000
+
+/* 2. IO & IDE configuration */
+
+#define BONITO_IODEVCFG			BONITO(BONITO_REGBASE + 0x08)
+
+/* 3. IO & IDE configuration */
+
+#define BONITO_SDCFG			BONITO(BONITO_REGBASE + 0x0c)
+
+/* 4. PCI address map control */
+
+#define BONITO_PCIMAP			BONITO(BONITO_REGBASE + 0x10)
+#define BONITO_PCIMEMBASECFG		BONITO(BONITO_REGBASE + 0x14)
+#define BONITO_PCIMAP_CFG		BONITO(BONITO_REGBASE + 0x18)
+
+/* 5. ICU & GPIO regs */
+
+/* GPIO Regs - r/w */
+
+#define BONITO_GPIODATA_OFFSET		0x1c
+#define BONITO_GPIODATA			BONITO(BONITO_REGBASE + BONITO_GPIODATA_OFFSET)
+#define BONITO_GPIOIE			BONITO(BONITO_REGBASE + 0x20)
+
+/* ICU Configuration Regs - r/w */
+
+#define BONITO_INTEDGE			BONITO(BONITO_REGBASE + 0x24)
+#define BONITO_INTSTEER			BONITO(BONITO_REGBASE + 0x28)
+#define BONITO_INTPOL			BONITO(BONITO_REGBASE + 0x2c)
+
+/* ICU Enable Regs - IntEn & IntISR are r/o. */
+
+#define BONITO_INTENSET			BONITO(BONITO_REGBASE + 0x30)
+#define BONITO_INTENCLR			BONITO(BONITO_REGBASE + 0x34)
+#define BONITO_INTEN			BONITO(BONITO_REGBASE + 0x38)
+#define BONITO_INTISR			BONITO(BONITO_REGBASE + 0x3c)
+
+/* PCI mail boxes */
+
+#define BONITO_PCIMAIL0_OFFSET		0x40
+#define BONITO_PCIMAIL1_OFFSET		0x44
+#define BONITO_PCIMAIL2_OFFSET		0x48
+#define BONITO_PCIMAIL3_OFFSET		0x4c
+#define BONITO_PCIMAIL0			BONITO(BONITO_REGBASE + 0x40)
+#define BONITO_PCIMAIL1			BONITO(BONITO_REGBASE + 0x44)
+#define BONITO_PCIMAIL2			BONITO(BONITO_REGBASE + 0x48)
+#define BONITO_PCIMAIL3			BONITO(BONITO_REGBASE + 0x4c)
+
+
+/* 6. PCI cache */
+
+#define BONITO_PCICACHECTRL		BONITO(BONITO_REGBASE + 0x50)
+#define BONITO_PCICACHETAG		BONITO(BONITO_REGBASE + 0x54)
+
+#define BONITO_PCIBADADDR		BONITO(BONITO_REGBASE + 0x58)
+#define BONITO_PCIMSTAT			BONITO(BONITO_REGBASE + 0x5c)
+
+
+/*
+#define BONITO_PCIRDPOST		BONITO(BONITO_REGBASE + 0x60)
+#define BONITO_PCIDATA			BONITO(BONITO_REGBASE + 0x64)
+*/
+
+/* 7. IDE DMA & Copier */
+
+#define BONITO_CONFIGBASE		0x000
+#define BONITO_BONITOBASE		0x100
+#define BONITO_LDMABASE			0x200
+#define BONITO_COPBASE			0x300
+#define BONITO_REG_BLOCKMASK		0x300
+
+#define BONITO_LDMACTRL			BONITO(BONITO_LDMABASE + 0x0)
+#define BONITO_LDMASTAT			BONITO(BONITO_LDMABASE + 0x0)
+#define BONITO_LDMAADDR			BONITO(BONITO_LDMABASE + 0x4)
+#define BONITO_LDMAGO			BONITO(BONITO_LDMABASE + 0x8)
+#define BONITO_LDMADATA			BONITO(BONITO_LDMABASE + 0xc)
+
+#define BONITO_COPCTRL			BONITO(BONITO_COPBASE + 0x0)
+#define BONITO_COPSTAT			BONITO(BONITO_COPBASE + 0x0)
+#define BONITO_COPPADDR			BONITO(BONITO_COPBASE + 0x4)
+#define BONITO_COPDADDR			BONITO(BONITO_COPBASE + 0x8)
+#define BONITO_COPGO			BONITO(BONITO_COPBASE + 0xc)
+
+
+/* ###### Bit Definitions for individual Registers #### */
+
+/* Gen DMA. */
+
+#define BONITO_IDECOPDADDR_DMA_DADDR	0x0ffffffc
+#define BONITO_IDECOPDADDR_DMA_DADDR_SHIFT	2
+#define BONITO_IDECOPPADDR_DMA_PADDR	0xfffffffc
+#define BONITO_IDECOPPADDR_DMA_PADDR_SHIFT	2
+#define BONITO_IDECOPGO_DMA_SIZE	0x0000fffe
+#define BONITO_IDECOPGO_DMA_SIZE_SHIFT	0
+#define BONITO_IDECOPGO_DMA_WRITE	0x00010000
+#define BONITO_IDECOPGO_DMAWCOUNT	0x000f0000
+#define BONITO_IDECOPGO_DMAWCOUNT_SHIFT 16
+
+#define BONITO_IDECOPCTRL_DMA_STARTBIT	0x80000000
+#define BONITO_IDECOPCTRL_DMA_RSTBIT	0x40000000
+
+/* DRAM - sdCfg */
+
+#define BONITO_SDCFG_AROWBITS		0x00000003
+#define BONITO_SDCFG_AROWBITS_SHIFT	0
+#define BONITO_SDCFG_ACOLBITS		0x0000000c
+#define BONITO_SDCFG_ACOLBITS_SHIFT	2
+#define BONITO_SDCFG_ABANKBIT		0x00000010
+#define BONITO_SDCFG_ASIDES		0x00000020
+#define BONITO_SDCFG_AABSENT		0x00000040
+#define BONITO_SDCFG_AWIDTH64		0x00000080
+
+#define BONITO_SDCFG_BROWBITS		0x00000300
+#define BONITO_SDCFG_BROWBITS_SHIFT	8
+#define BONITO_SDCFG_BCOLBITS		0x00000c00
+#define BONITO_SDCFG_BCOLBITS_SHIFT	10
+#define BONITO_SDCFG_BBANKBIT		0x00001000
+#define BONITO_SDCFG_BSIDES		0x00002000
+#define BONITO_SDCFG_BABSENT		0x00004000
+#define BONITO_SDCFG_BWIDTH64		0x00008000
+
+#define BONITO_SDCFG_EXTRDDATA		0x00010000
+#define BONITO_SDCFG_EXTRASCAS		0x00020000
+#define BONITO_SDCFG_EXTPRECH		0x00040000
+#define BONITO_SDCFG_EXTRASWIDTH	0x00180000
+#define BONITO_SDCFG_EXTRASWIDTH_SHIFT	19
+/* Changed by RPF 11-9-00 */
+#define BONITO_SDCFG_DRAMMODESET	0x00200000
+/* --- */
+#define BONITO_SDCFG_DRAMEXTREGS	0x00400000
+#define BONITO_SDCFG_DRAMPARITY		0x00800000
+/* Added by RPF 11-9-00 */
+#define BONITO_SDCFG_DRAMBURSTLEN	0x03000000
+#define BONITO_SDCFG_DRAMBURSTLEN_SHIFT 24
+#define BONITO_SDCFG_DRAMMODESET_DONE	0x80000000
+/* --- */
+
+/* PCI Cache - pciCacheCtrl */
+
+#define BONITO_PCICACHECTRL_CACHECMD	0x00000007
+#define BONITO_PCICACHECTRL_CACHECMD_SHIFT	0
+#define BONITO_PCICACHECTRL_CACHECMDLINE	0x00000018
+#define BONITO_PCICACHECTRL_CACHECMDLINE_SHIFT	3
+#define BONITO_PCICACHECTRL_CMDEXEC	0x00000020
+
+#define BONITO_PCICACHECTRL_IOBCCOH_PRES	0x00000100
+#define BONITO_PCICACHECTRL_IOBCCOH_EN	0x00000200
+#define BONITO_PCICACHECTRL_CPUCOH_PRES 0x00000400
+#define BONITO_PCICACHECTRL_CPUCOH_EN	0x00000800
+
+#define BONITO_IODEVCFG_BUFFBIT_CS0	0x00000001
+#define BONITO_IODEVCFG_SPEEDBIT_CS0	0x00000002
+#define BONITO_IODEVCFG_MOREABITS_CS0	0x00000004
+
+#define BONITO_IODEVCFG_BUFFBIT_CS1	0x00000008
+#define BONITO_IODEVCFG_SPEEDBIT_CS1	0x00000010
+#define BONITO_IODEVCFG_MOREABITS_CS1	0x00000020
+
+#define BONITO_IODEVCFG_BUFFBIT_CS2	0x00000040
+#define BONITO_IODEVCFG_SPEEDBIT_CS2	0x00000080
+#define BONITO_IODEVCFG_MOREABITS_CS2	0x00000100
+
+#define BONITO_IODEVCFG_BUFFBIT_CS3	0x00000200
+#define BONITO_IODEVCFG_SPEEDBIT_CS3	0x00000400
+#define BONITO_IODEVCFG_MOREABITS_CS3	0x00000800
+
+#define BONITO_IODEVCFG_BUFFBIT_IDE	0x00001000
+#define BONITO_IODEVCFG_SPEEDBIT_IDE	0x00002000
+#define BONITO_IODEVCFG_WORDSWAPBIT_IDE 0x00004000
+#define BONITO_IODEVCFG_MODEBIT_IDE	0x00008000
+#define BONITO_IODEVCFG_DMAON_IDE	0x001f0000
+#define BONITO_IODEVCFG_DMAON_IDE_SHIFT 16
+#define BONITO_IODEVCFG_DMAOFF_IDE	0x01e00000
+#define BONITO_IODEVCFG_DMAOFF_IDE_SHIFT	21
+#define BONITO_IODEVCFG_EPROMSPLIT	0x02000000
+/* Added by RPF 11-9-00 */
+#define BONITO_IODEVCFG_CPUCLOCKPERIOD	0xfc000000
+#define BONITO_IODEVCFG_CPUCLOCKPERIOD_SHIFT 26
+/* --- */
+
+/* gpio */
+#define BONITO_GPIO_GPIOW		0x000003ff
+#define BONITO_GPIO_GPIOW_SHIFT		0
+#define BONITO_GPIO_GPIOR		0x01ff0000
+#define BONITO_GPIO_GPIOR_SHIFT		16
+#define BONITO_GPIO_GPINR		0xfe000000
+#define BONITO_GPIO_GPINR_SHIFT		25
+#define BONITO_GPIO_IOW(N)		(1<<(BONITO_GPIO_GPIOW_SHIFT+(N)))
+#define BONITO_GPIO_IOR(N)		(1<<(BONITO_GPIO_GPIOR_SHIFT+(N)))
+#define BONITO_GPIO_INR(N)		(1<<(BONITO_GPIO_GPINR_SHIFT+(N)))
+
+/* ICU */
+#define BONITO_ICU_MBOXES		0x0000000f
+#define BONITO_ICU_MBOXES_SHIFT		0
+#define BONITO_ICU_DMARDY		0x00000010
+#define BONITO_ICU_DMAEMPTY		0x00000020
+#define BONITO_ICU_COPYRDY		0x00000040
+#define BONITO_ICU_COPYEMPTY		0x00000080
+#define BONITO_ICU_COPYERR		0x00000100
+#define BONITO_ICU_PCIIRQ		0x00000200
+#define BONITO_ICU_MASTERERR		0x00000400
+#define BONITO_ICU_SYSTEMERR		0x00000800
+#define BONITO_ICU_DRAMPERR		0x00001000
+#define BONITO_ICU_RETRYERR		0x00002000
+#define BONITO_ICU_GPIOS		0x01ff0000
+#define BONITO_ICU_GPIOS_SHIFT		16
+#define BONITO_ICU_GPINS		0x7e000000
+#define BONITO_ICU_GPINS_SHIFT		25
+#define BONITO_ICU_MBOX(N)		(1<<(BONITO_ICU_MBOXES_SHIFT+(N)))
+#define BONITO_ICU_GPIO(N)		(1<<(BONITO_ICU_GPIOS_SHIFT+(N)))
+#define BONITO_ICU_GPIN(N)		(1<<(BONITO_ICU_GPINS_SHIFT+(N)))
+
+/* pcimap */
+
+#define BONITO_PCIMAP_PCIMAP_LO0	0x0000003f
+#define BONITO_PCIMAP_PCIMAP_LO0_SHIFT	0
+#define BONITO_PCIMAP_PCIMAP_LO1	0x00000fc0
+#define BONITO_PCIMAP_PCIMAP_LO1_SHIFT	6
+#define BONITO_PCIMAP_PCIMAP_LO2	0x0003f000
+#define BONITO_PCIMAP_PCIMAP_LO2_SHIFT	12
+#define BONITO_PCIMAP_PCIMAP_2		0x00040000
+#define BONITO_PCIMAP_WIN(WIN, ADDR)	((((ADDR)>>26) & BONITO_PCIMAP_PCIMAP_LO0) << ((WIN)*6))
+
+#define BONITO_PCIMAP_WINSIZE		(1<<26)
+#define BONITO_PCIMAP_WINOFFSET(ADDR)	((ADDR) & (BONITO_PCIMAP_WINSIZE - 1))
+#define BONITO_PCIMAP_WINBASE(ADDR)	((ADDR) << 26)
+
+/* pcimembaseCfg */
+
+#define BONITO_PCIMEMBASECFG_MASK		0xf0000000
+#define BONITO_PCIMEMBASECFG_MEMBASE0_MASK	0x0000001f
+#define BONITO_PCIMEMBASECFG_MEMBASE0_MASK_SHIFT	0
+#define BONITO_PCIMEMBASECFG_MEMBASE0_TRANS	0x000003e0
+#define BONITO_PCIMEMBASECFG_MEMBASE0_TRANS_SHIFT	5
+#define BONITO_PCIMEMBASECFG_MEMBASE0_CACHED	0x00000400
+#define BONITO_PCIMEMBASECFG_MEMBASE0_IO	0x00000800
+
+#define BONITO_PCIMEMBASECFG_MEMBASE1_MASK	0x0001f000
+#define BONITO_PCIMEMBASECFG_MEMBASE1_MASK_SHIFT	12
+#define BONITO_PCIMEMBASECFG_MEMBASE1_TRANS	0x003e0000
+#define BONITO_PCIMEMBASECFG_MEMBASE1_TRANS_SHIFT	17
+#define BONITO_PCIMEMBASECFG_MEMBASE1_CACHED	0x00400000
+#define BONITO_PCIMEMBASECFG_MEMBASE1_IO	0x00800000
+
+#define BONITO_PCIMEMBASECFG_ASHIFT	23
+#define BONITO_PCIMEMBASECFG_AMASK		0x007fffff
+#define BONITO_PCIMEMBASECFGSIZE(WIN, SIZE)	(((~((SIZE)-1))>>(BONITO_PCIMEMBASECFG_ASHIFT-BONITO_PCIMEMBASECFG_MEMBASE##WIN##_MASK_SHIFT)) & BONITO_PCIMEMBASECFG_MEMBASE##WIN##_MASK)
+#define BONITO_PCIMEMBASECFGBASE(WIN, BASE)	(((BASE)>>(BONITO_PCIMEMBASECFG_ASHIFT-BONITO_PCIMEMBASECFG_MEMBASE##WIN##_TRANS_SHIFT)) & BONITO_PCIMEMBASECFG_MEMBASE##WIN##_TRANS)
+
+#define BONITO_PCIMEMBASECFG_SIZE(WIN, CFG)  (((((~(CFG)) & BONITO_PCIMEMBASECFG_MEMBASE##WIN##_MASK)) << (BONITO_PCIMEMBASECFG_ASHIFT - BONITO_PCIMEMBASECFG_MEMBASE##WIN##_MASK_SHIFT)) | BONITO_PCIMEMBASECFG_AMASK)
+
+
+#define BONITO_PCIMEMBASECFG_ADDRMASK(WIN, CFG)	 ((((CFG) & BONITO_PCIMEMBASECFG_MEMBASE##WIN##_MASK) >> BONITO_PCIMEMBASECFG_MEMBASE##WIN##_MASK_SHIFT) << BONITO_PCIMEMBASECFG_ASHIFT)
+#define BONITO_PCIMEMBASECFG_ADDRTRANS(WIN, CFG) ((((CFG) & BONITO_PCIMEMBASECFG_MEMBASE##WIN##_TRANS) >> BONITO_PCIMEMBASECFG_MEMBASE##WIN##_TRANS_SHIFT) << BONITO_PCIMEMBASECFG_ASHIFT)
+
+#define BONITO_PCITOPHYS(WIN, ADDR, CFG)	  ( \
+						  (((ADDR) & (~(BONITO_PCIMEMBASECFG_MASK))) & (~(BONITO_PCIMEMBASECFG_ADDRMASK(WIN, CFG)))) | \
+						  (BONITO_PCIMEMBASECFG_ADDRTRANS(WIN, CFG)) \
+						)
+
+/* PCICmd */
+
+#define BONITO_PCICMD_MEMEN		0x00000002
+#define BONITO_PCICMD_MSTREN		0x00000004
+
+
+#endif /* _ASM_MIPS_BOARDS_BONITO64_H */
diff --git a/arch/mips/include/asm/mips-boards/generic.h b/arch/mips/include/asm/mips-boards/generic.h
new file mode 100644
index 000000000..c904c2455
--- /dev/null
+++ b/arch/mips/include/asm/mips-boards/generic.h
@@ -0,0 +1,79 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Defines of the MIPS boards specific address-MAP, registers, etc.
+ *
+ * Copyright (C) 2000,2012 MIPS Technologies, Inc.
+ * All rights reserved.
+ * Authors: Carsten Langgaard <carstenl@mips.com>
+ *          Steven J. Hill <sjhill@mips.com>
+ */
+#ifndef __ASM_MIPS_BOARDS_GENERIC_H
+#define __ASM_MIPS_BOARDS_GENERIC_H
+
+#include <asm/addrspace.h>
+#include <asm/byteorder.h>
+#include <asm/mips-boards/bonito64.h>
+
+/*
+ * Display register base.
+ */
+#define ASCII_DISPLAY_WORD_BASE	   0x1f000410
+#define ASCII_DISPLAY_POS_BASE	   0x1f000418
+
+/*
+ * Revision register.
+ */
+#define MIPS_REVISION_REG		   0x1fc00010
+#define MIPS_REVISION_CORID_QED_RM5261	   0
+#define MIPS_REVISION_CORID_CORE_LV	   1
+#define MIPS_REVISION_CORID_BONITO64	   2
+#define MIPS_REVISION_CORID_CORE_20K	   3
+#define MIPS_REVISION_CORID_CORE_FPGA	   4
+#define MIPS_REVISION_CORID_CORE_MSC	   5
+#define MIPS_REVISION_CORID_CORE_EMUL	   6
+#define MIPS_REVISION_CORID_CORE_FPGA2	   7
+#define MIPS_REVISION_CORID_CORE_FPGAR2	   8
+#define MIPS_REVISION_CORID_CORE_FPGA3	   9
+#define MIPS_REVISION_CORID_CORE_24K	   10
+#define MIPS_REVISION_CORID_CORE_FPGA4	   11
+#define MIPS_REVISION_CORID_CORE_FPGA5	   12
+
+/**** Artificial corid defines ****/
+/*
+ *  CoreEMUL with   Bonito   System Controller is treated like a Core20K
+ *  CoreEMUL with SOC-it 101 System Controller is treated like a CoreMSC
+ */
+#define MIPS_REVISION_CORID_CORE_EMUL_BON  -1
+#define MIPS_REVISION_CORID_CORE_EMUL_MSC  -2
+
+#define MIPS_REVISION_CORID (((*(volatile u32 *)ioremap(MIPS_REVISION_REG, 4)) >> 10) & 0x3f)
+
+#define MIPS_REVISION_SCON_OTHER	   0
+#define MIPS_REVISION_SCON_SOCITSC	   1
+#define MIPS_REVISION_SCON_SOCITSCP	   2
+
+/* Artificial SCON defines for MIPS_REVISION_SCON_OTHER */
+#define MIPS_REVISION_SCON_UNKNOWN	   -1
+#define MIPS_REVISION_SCON_GT64120	   -2
+#define MIPS_REVISION_SCON_BONITO	   -3
+#define MIPS_REVISION_SCON_BRTL		   -4
+#define MIPS_REVISION_SCON_SOCIT	   -5
+#define MIPS_REVISION_SCON_ROCIT	   -6
+
+#define MIPS_REVISION_SCONID (((*(volatile u32 *)ioremap(MIPS_REVISION_REG, 4)) >> 24) & 0xff)
+
+extern int mips_revision_sconid;
+
+#ifdef CONFIG_PCI
+extern void mips_pcibios_init(void);
+#else
+#define mips_pcibios_init() do { } while (0)
+#endif
+
+extern void mips_scroll_message(void);
+extern void mips_display_message(const char *str);
+
+#endif	/* __ASM_MIPS_BOARDS_GENERIC_H */
diff --git a/arch/mips/include/asm/mips-boards/launch.h b/arch/mips/include/asm/mips-boards/launch.h
new file mode 100644
index 000000000..3481ed4c1
--- /dev/null
+++ b/arch/mips/include/asm/mips-boards/launch.h
@@ -0,0 +1,41 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ *
+ */
+
+#ifndef _ASM_MIPS_BOARDS_LAUNCH_H
+#define _ASM_MIPS_BOARDS_LAUNCH_H
+
+#ifndef _ASSEMBLER_
+
+struct cpulaunch {
+    unsigned long	pc;
+    unsigned long	gp;
+    unsigned long	sp;
+    unsigned long	a0;
+    unsigned long	_pad[3]; /* pad to cache line size to avoid thrashing */
+    unsigned long	flags;
+};
+
+#else
+
+#define LOG2CPULAUNCH	5
+#define LAUNCH_PC	0
+#define LAUNCH_GP	4
+#define LAUNCH_SP	8
+#define LAUNCH_A0	12
+#define LAUNCH_FLAGS	28
+
+#endif
+
+#define LAUNCH_FREADY	1
+#define LAUNCH_FGO	2
+#define LAUNCH_FGONE	4
+
+#define CPULAUNCH	0x00000f00
+#define NCPULAUNCH	8
+
+/* Polling period in count cycles for secondary CPU's */
+#define LAUNCHPERIOD	10000
+
+#endif /* _ASM_MIPS_BOARDS_LAUNCH_H */
diff --git a/arch/mips/include/asm/mips-boards/malta.h b/arch/mips/include/asm/mips-boards/malta.h
new file mode 100644
index 000000000..254be3d62
--- /dev/null
+++ b/arch/mips/include/asm/mips-boards/malta.h
@@ -0,0 +1,97 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 2000 MIPS Technologies, Inc.  All rights reserved.
+ *
+ * Defines of the Malta board specific address-MAP, registers, etc.
+ */
+#ifndef __ASM_MIPS_BOARDS_MALTA_H
+#define __ASM_MIPS_BOARDS_MALTA_H
+
+#include <asm/addrspace.h>
+#include <asm/io.h>
+#include <asm/mips-boards/msc01_pci.h>
+#include <asm/gt64120.h>
+
+/* Mips interrupt controller found in SOCit variations */
+#define MIPS_MSC01_IC_REG_BASE		0x1bc40000
+#define MIPS_SOCITSC_IC_REG_BASE	0x1ffa0000
+
+/*
+ * Malta I/O ports base address for the Galileo GT64120 and Algorithmics
+ * Bonito system controllers.
+ */
+#define MALTA_GT_PORT_BASE	get_gt_port_base(GT_PCI0IOLD_OFS)
+#define MALTA_BONITO_PORT_BASE	((unsigned long)ioremap (0x1fd00000, 0x10000))
+#define MALTA_MSC_PORT_BASE	get_msc_port_base(MSC01_PCI_SC2PIOBASL)
+
+static inline unsigned long get_gt_port_base(unsigned long reg)
+{
+	unsigned long addr;
+	addr = GT_READ(reg);
+	return (unsigned long) ioremap (((addr & 0xffff) << 21), 0x10000);
+}
+
+static inline unsigned long get_msc_port_base(unsigned long reg)
+{
+	unsigned long addr;
+	MSC_READ(reg, addr);
+	return (unsigned long) ioremap(addr, 0x10000);
+}
+
+/*
+ * GCMP Specific definitions
+ */
+#define GCMP_BASE_ADDR			0x1fbf8000
+#define GCMP_ADDRSPACE_SZ		(256 * 1024)
+
+/*
+ * GIC Specific definitions
+ */
+#define GIC_BASE_ADDR			0x1bdc0000
+#define GIC_ADDRSPACE_SZ		(128 * 1024)
+
+/*
+ * CPC Specific definitions
+ */
+#define CPC_BASE_ADDR			0x1bde0000
+
+/*
+ * MSC01 BIU Specific definitions
+ * FIXME : These should be elsewhere ?
+ */
+#define MSC01_BIU_REG_BASE		0x1bc80000
+#define MSC01_BIU_ADDRSPACE_SZ		(256 * 1024)
+#define MSC01_SC_CFG_OFS		0x0110
+#define MSC01_SC_CFG_GICPRES_MSK	0x00000004
+#define MSC01_SC_CFG_GICPRES_SHF	2
+#define MSC01_SC_CFG_GICENA_SHF		3
+
+/*
+ * Malta RTC-device indirect register access.
+ */
+#define MALTA_RTC_ADR_REG	0x70
+#define MALTA_RTC_DAT_REG	0x71
+
+/*
+ * Malta SMSC FDC37M817 Super I/O Controller register.
+ */
+#define SMSC_CONFIG_REG		0x3f0
+#define SMSC_DATA_REG		0x3f1
+
+#define SMSC_CONFIG_DEVNUM	0x7
+#define SMSC_CONFIG_ACTIVATE	0x30
+#define SMSC_CONFIG_ENTER	0x55
+#define SMSC_CONFIG_EXIT	0xaa
+
+#define SMSC_CONFIG_DEVNUM_FLOPPY     0
+
+#define SMSC_CONFIG_ACTIVATE_ENABLE   1
+
+#define SMSC_WRITE(x, a)     outb(x, a)
+
+#define MALTA_JMPRS_REG		0x1f000210
+
+extern void __init *malta_dt_shim(void *fdt);
+
+#endif /* __ASM_MIPS_BOARDS_MALTA_H */
diff --git a/arch/mips/include/asm/mips-boards/maltaint.h b/arch/mips/include/asm/mips-boards/maltaint.h
new file mode 100644
index 000000000..817698abf
--- /dev/null
+++ b/arch/mips/include/asm/mips-boards/maltaint.h
@@ -0,0 +1,63 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2000,2012 MIPS Technologies, Inc.  All rights reserved.
+ *	Carsten Langgaard <carstenl@mips.com>
+ *	Steven J. Hill <sjhill@mips.com>
+ */
+#ifndef _MIPS_MALTAINT_H
+#define _MIPS_MALTAINT_H
+
+/*
+ * Interrupts 0..15 are used for Malta ISA compatible interrupts
+ */
+#define MALTA_INT_BASE		0
+
+/* CPU interrupt offsets */
+#define MIPSCPU_INT_SW0		0
+#define MIPSCPU_INT_SW1		1
+#define MIPSCPU_INT_MB0		2
+#define MIPSCPU_INT_I8259A	MIPSCPU_INT_MB0
+#define MIPSCPU_INT_GIC		MIPSCPU_INT_MB0 /* GIC chained interrupt */
+#define MIPSCPU_INT_MB1		3
+#define MIPSCPU_INT_SMI		MIPSCPU_INT_MB1
+#define MIPSCPU_INT_MB2		4
+#define MIPSCPU_INT_MB3		5
+#define MIPSCPU_INT_COREHI	MIPSCPU_INT_MB3
+#define MIPSCPU_INT_MB4		6
+#define MIPSCPU_INT_CORELO	MIPSCPU_INT_MB4
+
+/*
+ * Interrupts 96..127 are used for Soc-it Classic interrupts
+ */
+#define MSC01C_INT_BASE		96
+
+/* SOC-it Classic interrupt offsets */
+#define MSC01C_INT_TMR		0
+#define MSC01C_INT_PCI		1
+
+/*
+ * Interrupts 96..127 are used for Soc-it EIC interrupts
+ */
+#define MSC01E_INT_BASE		96
+
+/* SOC-it EIC interrupt offsets */
+#define MSC01E_INT_SW0		1
+#define MSC01E_INT_SW1		2
+#define MSC01E_INT_MB0		3
+#define MSC01E_INT_I8259A	MSC01E_INT_MB0
+#define MSC01E_INT_MB1		4
+#define MSC01E_INT_SMI		MSC01E_INT_MB1
+#define MSC01E_INT_MB2		5
+#define MSC01E_INT_MB3		6
+#define MSC01E_INT_COREHI	MSC01E_INT_MB3
+#define MSC01E_INT_MB4		7
+#define MSC01E_INT_CORELO	MSC01E_INT_MB4
+#define MSC01E_INT_TMR		8
+#define MSC01E_INT_PCI		9
+#define MSC01E_INT_PERFCTR	10
+#define MSC01E_INT_CPUCTR	11
+
+#endif /* !(_MIPS_MALTAINT_H) */
diff --git a/arch/mips/include/asm/mips-boards/msc01_pci.h b/arch/mips/include/asm/mips-boards/msc01_pci.h
new file mode 100644
index 000000000..e036b7dd6
--- /dev/null
+++ b/arch/mips/include/asm/mips-boards/msc01_pci.h
@@ -0,0 +1,258 @@
+/*
+ * PCI Register definitions for the MIPS System Controller.
+ *
+ * Copyright (C) 2002, 2005  MIPS Technologies, Inc.  All rights reserved.
+ *	Authors: Carsten Langgaard <carstenl@mips.com>
+ *		 Maciej W. Rozycki <macro@mips.com>
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#ifndef __ASM_MIPS_BOARDS_MSC01_PCI_H
+#define __ASM_MIPS_BOARDS_MSC01_PCI_H
+
+/*
+ * Register offset addresses
+ */
+
+#define MSC01_PCI_ID_OFS		0x0000
+#define MSC01_PCI_SC2PMBASL_OFS		0x0208
+#define MSC01_PCI_SC2PMMSKL_OFS		0x0218
+#define MSC01_PCI_SC2PMMAPL_OFS		0x0228
+#define MSC01_PCI_SC2PIOBASL_OFS	0x0248
+#define MSC01_PCI_SC2PIOMSKL_OFS	0x0258
+#define MSC01_PCI_SC2PIOMAPL_OFS	0x0268
+#define MSC01_PCI_P2SCMSKL_OFS		0x0308
+#define MSC01_PCI_P2SCMAPL_OFS		0x0318
+#define MSC01_PCI_INTCFG_OFS		0x0600
+#define MSC01_PCI_INTSTAT_OFS		0x0608
+#define MSC01_PCI_CFGADDR_OFS		0x0610
+#define MSC01_PCI_CFGDATA_OFS		0x0618
+#define MSC01_PCI_IACK_OFS		0x0620
+#define MSC01_PCI_HEAD0_OFS		0x2000	/* DevID, VendorID */
+#define MSC01_PCI_HEAD1_OFS		0x2008	/* Status, Command */
+#define MSC01_PCI_HEAD2_OFS		0x2010	/* Class code, RevID */
+#define MSC01_PCI_HEAD3_OFS		0x2018	/* bist, header, latency */
+#define MSC01_PCI_HEAD4_OFS		0x2020	/* BAR 0 */
+#define MSC01_PCI_HEAD5_OFS		0x2028	/* BAR 1 */
+#define MSC01_PCI_HEAD6_OFS		0x2030	/* BAR 2 */
+#define MSC01_PCI_HEAD7_OFS		0x2038	/* BAR 3 */
+#define MSC01_PCI_HEAD8_OFS		0x2040	/* BAR 4 */
+#define MSC01_PCI_HEAD9_OFS		0x2048	/* BAR 5 */
+#define MSC01_PCI_HEAD10_OFS		0x2050	/* CardBus CIS Ptr */
+#define MSC01_PCI_HEAD11_OFS		0x2058	/* SubSystem ID, -VendorID */
+#define MSC01_PCI_HEAD12_OFS		0x2060	/* ROM BAR */
+#define MSC01_PCI_HEAD13_OFS		0x2068	/* Capabilities ptr */
+#define MSC01_PCI_HEAD14_OFS		0x2070	/* reserved */
+#define MSC01_PCI_HEAD15_OFS		0x2078	/* Maxl, ming, intpin, int */
+#define MSC01_PCI_BAR0_OFS		0x2220
+#define MSC01_PCI_CFG_OFS		0x2380
+#define MSC01_PCI_SWAP_OFS		0x2388
+
+
+/*****************************************************************************
+ * Register encodings
+ ****************************************************************************/
+
+#define MSC01_PCI_ID_ID_SHF		16
+#define MSC01_PCI_ID_ID_MSK		0x00ff0000
+#define MSC01_PCI_ID_ID_HOSTBRIDGE	82
+#define MSC01_PCI_ID_MAR_SHF		8
+#define MSC01_PCI_ID_MAR_MSK		0x0000ff00
+#define MSC01_PCI_ID_MIR_SHF		0
+#define MSC01_PCI_ID_MIR_MSK		0x000000ff
+
+#define MSC01_PCI_SC2PMBASL_BAS_SHF	24
+#define MSC01_PCI_SC2PMBASL_BAS_MSK	0xff000000
+
+#define MSC01_PCI_SC2PMMSKL_MSK_SHF	24
+#define MSC01_PCI_SC2PMMSKL_MSK_MSK	0xff000000
+
+#define MSC01_PCI_SC2PMMAPL_MAP_SHF	24
+#define MSC01_PCI_SC2PMMAPL_MAP_MSK	0xff000000
+
+#define MSC01_PCI_SC2PIOBASL_BAS_SHF	24
+#define MSC01_PCI_SC2PIOBASL_BAS_MSK	0xff000000
+
+#define MSC01_PCI_SC2PIOMSKL_MSK_SHF	24
+#define MSC01_PCI_SC2PIOMSKL_MSK_MSK	0xff000000
+
+#define MSC01_PCI_SC2PIOMAPL_MAP_SHF	24
+#define MSC01_PCI_SC2PIOMAPL_MAP_MSK	0xff000000
+
+#define MSC01_PCI_P2SCMSKL_MSK_SHF	24
+#define MSC01_PCI_P2SCMSKL_MSK_MSK	0xff000000
+
+#define MSC01_PCI_P2SCMAPL_MAP_SHF	24
+#define MSC01_PCI_P2SCMAPL_MAP_MSK	0xff000000
+
+#define MSC01_PCI_INTCFG_RST_SHF	10
+#define MSC01_PCI_INTCFG_RST_MSK	0x00000400
+#define MSC01_PCI_INTCFG_RST_BIT	0x00000400
+#define MSC01_PCI_INTCFG_MWE_SHF	9
+#define MSC01_PCI_INTCFG_MWE_MSK	0x00000200
+#define MSC01_PCI_INTCFG_MWE_BIT	0x00000200
+#define MSC01_PCI_INTCFG_DTO_SHF	8
+#define MSC01_PCI_INTCFG_DTO_MSK	0x00000100
+#define MSC01_PCI_INTCFG_DTO_BIT	0x00000100
+#define MSC01_PCI_INTCFG_MA_SHF		7
+#define MSC01_PCI_INTCFG_MA_MSK		0x00000080
+#define MSC01_PCI_INTCFG_MA_BIT		0x00000080
+#define MSC01_PCI_INTCFG_TA_SHF		6
+#define MSC01_PCI_INTCFG_TA_MSK		0x00000040
+#define MSC01_PCI_INTCFG_TA_BIT		0x00000040
+#define MSC01_PCI_INTCFG_RTY_SHF	5
+#define MSC01_PCI_INTCFG_RTY_MSK	0x00000020
+#define MSC01_PCI_INTCFG_RTY_BIT	0x00000020
+#define MSC01_PCI_INTCFG_MWP_SHF	4
+#define MSC01_PCI_INTCFG_MWP_MSK	0x00000010
+#define MSC01_PCI_INTCFG_MWP_BIT	0x00000010
+#define MSC01_PCI_INTCFG_MRP_SHF	3
+#define MSC01_PCI_INTCFG_MRP_MSK	0x00000008
+#define MSC01_PCI_INTCFG_MRP_BIT	0x00000008
+#define MSC01_PCI_INTCFG_SWP_SHF	2
+#define MSC01_PCI_INTCFG_SWP_MSK	0x00000004
+#define MSC01_PCI_INTCFG_SWP_BIT	0x00000004
+#define MSC01_PCI_INTCFG_SRP_SHF	1
+#define MSC01_PCI_INTCFG_SRP_MSK	0x00000002
+#define MSC01_PCI_INTCFG_SRP_BIT	0x00000002
+#define MSC01_PCI_INTCFG_SE_SHF		0
+#define MSC01_PCI_INTCFG_SE_MSK		0x00000001
+#define MSC01_PCI_INTCFG_SE_BIT		0x00000001
+
+#define MSC01_PCI_INTSTAT_RST_SHF	10
+#define MSC01_PCI_INTSTAT_RST_MSK	0x00000400
+#define MSC01_PCI_INTSTAT_RST_BIT	0x00000400
+#define MSC01_PCI_INTSTAT_MWE_SHF	9
+#define MSC01_PCI_INTSTAT_MWE_MSK	0x00000200
+#define MSC01_PCI_INTSTAT_MWE_BIT	0x00000200
+#define MSC01_PCI_INTSTAT_DTO_SHF	8
+#define MSC01_PCI_INTSTAT_DTO_MSK	0x00000100
+#define MSC01_PCI_INTSTAT_DTO_BIT	0x00000100
+#define MSC01_PCI_INTSTAT_MA_SHF	7
+#define MSC01_PCI_INTSTAT_MA_MSK	0x00000080
+#define MSC01_PCI_INTSTAT_MA_BIT	0x00000080
+#define MSC01_PCI_INTSTAT_TA_SHF	6
+#define MSC01_PCI_INTSTAT_TA_MSK	0x00000040
+#define MSC01_PCI_INTSTAT_TA_BIT	0x00000040
+#define MSC01_PCI_INTSTAT_RTY_SHF	5
+#define MSC01_PCI_INTSTAT_RTY_MSK	0x00000020
+#define MSC01_PCI_INTSTAT_RTY_BIT	0x00000020
+#define MSC01_PCI_INTSTAT_MWP_SHF	4
+#define MSC01_PCI_INTSTAT_MWP_MSK	0x00000010
+#define MSC01_PCI_INTSTAT_MWP_BIT	0x00000010
+#define MSC01_PCI_INTSTAT_MRP_SHF	3
+#define MSC01_PCI_INTSTAT_MRP_MSK	0x00000008
+#define MSC01_PCI_INTSTAT_MRP_BIT	0x00000008
+#define MSC01_PCI_INTSTAT_SWP_SHF	2
+#define MSC01_PCI_INTSTAT_SWP_MSK	0x00000004
+#define MSC01_PCI_INTSTAT_SWP_BIT	0x00000004
+#define MSC01_PCI_INTSTAT_SRP_SHF	1
+#define MSC01_PCI_INTSTAT_SRP_MSK	0x00000002
+#define MSC01_PCI_INTSTAT_SRP_BIT	0x00000002
+#define MSC01_PCI_INTSTAT_SE_SHF	0
+#define MSC01_PCI_INTSTAT_SE_MSK	0x00000001
+#define MSC01_PCI_INTSTAT_SE_BIT	0x00000001
+
+#define MSC01_PCI_CFGADDR_BNUM_SHF	16
+#define MSC01_PCI_CFGADDR_BNUM_MSK	0x00ff0000
+#define MSC01_PCI_CFGADDR_DNUM_SHF	11
+#define MSC01_PCI_CFGADDR_DNUM_MSK	0x0000f800
+#define MSC01_PCI_CFGADDR_FNUM_SHF	8
+#define MSC01_PCI_CFGADDR_FNUM_MSK	0x00000700
+#define MSC01_PCI_CFGADDR_RNUM_SHF	2
+#define MSC01_PCI_CFGADDR_RNUM_MSK	0x000000fc
+
+#define MSC01_PCI_CFGDATA_DATA_SHF	0
+#define MSC01_PCI_CFGDATA_DATA_MSK	0xffffffff
+
+/* The defines below are ONLY valid for a MEM bar! */
+#define MSC01_PCI_BAR0_SIZE_SHF		4
+#define MSC01_PCI_BAR0_SIZE_MSK		0xfffffff0
+#define MSC01_PCI_BAR0_P_SHF		3
+#define MSC01_PCI_BAR0_P_MSK		0x00000008
+#define MSC01_PCI_BAR0_P_BIT		MSC01_PCI_BAR0_P_MSK
+#define MSC01_PCI_BAR0_D_SHF		1
+#define MSC01_PCI_BAR0_D_MSK		0x00000006
+#define MSC01_PCI_BAR0_T_SHF		0
+#define MSC01_PCI_BAR0_T_MSK		0x00000001
+#define MSC01_PCI_BAR0_T_BIT		MSC01_PCI_BAR0_T_MSK
+
+
+#define MSC01_PCI_CFG_RA_SHF		17
+#define MSC01_PCI_CFG_RA_MSK		0x00020000
+#define MSC01_PCI_CFG_RA_BIT		MSC01_PCI_CFG_RA_MSK
+#define MSC01_PCI_CFG_G_SHF		16
+#define MSC01_PCI_CFG_G_MSK		0x00010000
+#define MSC01_PCI_CFG_G_BIT		MSC01_PCI_CFG_G_MSK
+#define MSC01_PCI_CFG_EN_SHF		15
+#define MSC01_PCI_CFG_EN_MSK		0x00008000
+#define MSC01_PCI_CFG_EN_BIT		MSC01_PCI_CFG_EN_MSK
+#define MSC01_PCI_CFG_MAXRTRY_SHF	0
+#define MSC01_PCI_CFG_MAXRTRY_MSK	0x00000fff
+
+#define MSC01_PCI_SWAP_IO_SHF		18
+#define MSC01_PCI_SWAP_IO_MSK		0x000c0000
+#define MSC01_PCI_SWAP_MEM_SHF		16
+#define MSC01_PCI_SWAP_MEM_MSK		0x00030000
+#define MSC01_PCI_SWAP_BAR0_SHF		0
+#define MSC01_PCI_SWAP_BAR0_MSK		0x00000003
+#define MSC01_PCI_SWAP_NOSWAP		0
+#define MSC01_PCI_SWAP_BYTESWAP		1
+
+/*
+ * MIPS System controller PCI register base.
+ *
+ * FIXME - are these macros specific to Malta and co or to the MSC?  If the
+ * latter, they should be moved elsewhere.
+ */
+#define MIPS_MSC01_PCI_REG_BASE		0x1bd00000
+#define MIPS_SOCITSC_PCI_REG_BASE	0x1ff10000
+
+extern unsigned long _pcictrl_msc;
+
+#define MSC01_PCI_REG_BASE	_pcictrl_msc
+
+#define MSC_WRITE(reg, data)	do { *(volatile u32 *)(reg) = data; } while (0)
+#define MSC_READ(reg, data)	do { data = *(volatile u32 *)(reg); } while (0)
+
+/*
+ * Registers absolute addresses
+ */
+
+#define MSC01_PCI_ID		(MSC01_PCI_REG_BASE + MSC01_PCI_ID_OFS)
+#define MSC01_PCI_SC2PMBASL	(MSC01_PCI_REG_BASE + MSC01_PCI_SC2PMBASL_OFS)
+#define MSC01_PCI_SC2PMMSKL	(MSC01_PCI_REG_BASE + MSC01_PCI_SC2PMMSKL_OFS)
+#define MSC01_PCI_SC2PMMAPL	(MSC01_PCI_REG_BASE + MSC01_PCI_SC2PMMAPL_OFS)
+#define MSC01_PCI_SC2PIOBASL	(MSC01_PCI_REG_BASE + MSC01_PCI_SC2PIOBASL_OFS)
+#define MSC01_PCI_SC2PIOMSKL	(MSC01_PCI_REG_BASE + MSC01_PCI_SC2PIOMSKL_OFS)
+#define MSC01_PCI_SC2PIOMAPL	(MSC01_PCI_REG_BASE + MSC01_PCI_SC2PIOMAPL_OFS)
+#define MSC01_PCI_P2SCMSKL	(MSC01_PCI_REG_BASE + MSC01_PCI_P2SCMSKL_OFS)
+#define MSC01_PCI_P2SCMAPL	(MSC01_PCI_REG_BASE + MSC01_PCI_P2SCMAPL_OFS)
+#define MSC01_PCI_INTCFG	(MSC01_PCI_REG_BASE + MSC01_PCI_INTCFG_OFS)
+#define MSC01_PCI_INTSTAT	(MSC01_PCI_REG_BASE + MSC01_PCI_INTSTAT_OFS)
+#define MSC01_PCI_CFGADDR	(MSC01_PCI_REG_BASE + MSC01_PCI_CFGADDR_OFS)
+#define MSC01_PCI_CFGDATA	(MSC01_PCI_REG_BASE + MSC01_PCI_CFGDATA_OFS)
+#define MSC01_PCI_IACK		(MSC01_PCI_REG_BASE + MSC01_PCI_IACK_OFS)
+#define MSC01_PCI_HEAD0		(MSC01_PCI_REG_BASE + MSC01_PCI_HEAD0_OFS)
+#define MSC01_PCI_HEAD1		(MSC01_PCI_REG_BASE + MSC01_PCI_HEAD1_OFS)
+#define MSC01_PCI_HEAD2		(MSC01_PCI_REG_BASE + MSC01_PCI_HEAD2_OFS)
+#define MSC01_PCI_HEAD3		(MSC01_PCI_REG_BASE + MSC01_PCI_HEAD3_OFS)
+#define MSC01_PCI_HEAD4		(MSC01_PCI_REG_BASE + MSC01_PCI_HEAD4_OFS)
+#define MSC01_PCI_HEAD5		(MSC01_PCI_REG_BASE + MSC01_PCI_HEAD5_OFS)
+#define MSC01_PCI_HEAD6		(MSC01_PCI_REG_BASE + MSC01_PCI_HEAD6_OFS)
+#define MSC01_PCI_HEAD7		(MSC01_PCI_REG_BASE + MSC01_PCI_HEAD7_OFS)
+#define MSC01_PCI_HEAD8		(MSC01_PCI_REG_BASE + MSC01_PCI_HEAD8_OFS)
+#define MSC01_PCI_HEAD9		(MSC01_PCI_REG_BASE + MSC01_PCI_HEAD9_OFS)
+#define MSC01_PCI_HEAD10	(MSC01_PCI_REG_BASE + MSC01_PCI_HEAD10_OFS)
+#define MSC01_PCI_HEAD11	(MSC01_PCI_REG_BASE + MSC01_PCI_HEAD11_OFS)
+#define MSC01_PCI_HEAD12	(MSC01_PCI_REG_BASE + MSC01_PCI_HEAD11_OFS)
+#define MSC01_PCI_HEAD13	(MSC01_PCI_REG_BASE + MSC01_PCI_HEAD11_OFS)
+#define MSC01_PCI_HEAD14	(MSC01_PCI_REG_BASE + MSC01_PCI_HEAD11_OFS)
+#define MSC01_PCI_HEAD15	(MSC01_PCI_REG_BASE + MSC01_PCI_HEAD11_OFS)
+#define MSC01_PCI_BAR0		(MSC01_PCI_REG_BASE + MSC01_PCI_BAR0_OFS)
+#define MSC01_PCI_CFG		(MSC01_PCI_REG_BASE + MSC01_PCI_CFG_OFS)
+#define MSC01_PCI_SWAP		(MSC01_PCI_REG_BASE + MSC01_PCI_SWAP_OFS)
+
+#endif /* __ASM_MIPS_BOARDS_MSC01_PCI_H */
diff --git a/arch/mips/include/asm/mips-boards/piix4.h b/arch/mips/include/asm/mips-boards/piix4.h
new file mode 100644
index 000000000..e174bc7c8
--- /dev/null
+++ b/arch/mips/include/asm/mips-boards/piix4.h
@@ -0,0 +1,58 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 2000 MIPS Technologies, Inc.  All rights reserved.
+ * Copyright (C) 2013 Imagination Technologies Ltd.
+ *
+ * Register definitions for Intel PIIX4 South Bridge Device.
+ */
+#ifndef __ASM_MIPS_BOARDS_PIIX4_H
+#define __ASM_MIPS_BOARDS_PIIX4_H
+
+/* PIRQX Route Control */
+#define PIIX4_FUNC0_PIRQRC			0x60
+#define   PIIX4_FUNC0_PIRQRC_IRQ_ROUTING_DISABLE	(1 << 7)
+#define   PIIX4_FUNC0_PIRQRC_IRQ_ROUTING_MASK		0xf
+#define   PIIX4_FUNC0_PIRQRC_IRQ_ROUTING_MAX		16
+/* SERIRQ Control */
+#define PIIX4_FUNC0_SERIRQC			0x64
+#define   PIIX4_FUNC0_SERIRQC_EN			(1 << 7)
+#define   PIIX4_FUNC0_SERIRQC_CONT			(1 << 6)
+/* Top Of Memory */
+#define PIIX4_FUNC0_TOM				0x69
+#define   PIIX4_FUNC0_TOM_TOP_OF_MEMORY_MASK		0xf0
+/* Deterministic Latency Control */
+#define PIIX4_FUNC0_DLC				0x82
+#define   PIIX4_FUNC0_DLC_USBPR_EN			(1 << 2)
+#define   PIIX4_FUNC0_DLC_PASSIVE_RELEASE_EN		(1 << 1)
+#define   PIIX4_FUNC0_DLC_DELAYED_TRANSACTION_EN	(1 << 0)
+/* General Configuration */
+#define PIIX4_FUNC0_GENCFG			0xb0
+#define   PIIX4_FUNC0_GENCFG_SERIRQ			(1 << 16)
+
+/* IDE Timing */
+#define PIIX4_FUNC1_IDETIM_PRIMARY_LO		0x40
+#define PIIX4_FUNC1_IDETIM_PRIMARY_HI		0x41
+#define   PIIX4_FUNC1_IDETIM_PRIMARY_HI_IDE_DECODE_EN	(1 << 7)
+#define PIIX4_FUNC1_IDETIM_SECONDARY_LO		0x42
+#define PIIX4_FUNC1_IDETIM_SECONDARY_HI		0x43
+#define   PIIX4_FUNC1_IDETIM_SECONDARY_HI_IDE_DECODE_EN	(1 << 7)
+
+/* Power Management Configuration Space */
+#define PIIX4_FUNC3_PMBA			0x40
+#define PIIX4_FUNC3_PMREGMISC			0x80
+#define   PIIX4_FUNC3_PMREGMISC_EN			(1 << 0)
+
+/* Power Management IO Space */
+#define PIIX4_FUNC3IO_PMSTS			0x00
+#define   PIIX4_FUNC3IO_PMSTS_PWRBTN_STS		(1 << 8)
+#define PIIX4_FUNC3IO_PMCNTRL			0x04
+#define   PIIX4_FUNC3IO_PMCNTRL_SUS_EN			(1 << 13)
+#define   PIIX4_FUNC3IO_PMCNTRL_SUS_TYP			(0x7 << 10)
+#define   PIIX4_FUNC3IO_PMCNTRL_SUS_TYP_SOFF		(0x0 << 10)
+#define   PIIX4_FUNC3IO_PMCNTRL_SUS_TYP_STR		(0x1 << 10)
+
+/* Data for magic special PCI cycle */
+#define PIIX4_SUSPEND_MAGIC			0x00120002
+
+#endif /* __ASM_MIPS_BOARDS_PIIX4_H */
diff --git a/arch/mips/include/asm/mips-boards/sead3-addr.h b/arch/mips/include/asm/mips-boards/sead3-addr.h
new file mode 100644
index 000000000..c0db57802
--- /dev/null
+++ b/arch/mips/include/asm/mips-boards/sead3-addr.h
@@ -0,0 +1,83 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2015 Imagination Technologies, Inc.
+ *   written by Ralf Baechle <ralf@linux-mips.org>
+ */
+#ifndef __ASM_MIPS_BOARDS_SEAD3_ADDR_H
+#define __ASM_MIPS_BOARDS_SEAD3_ADDR_H
+
+/*
+ * Target #0 Register Decode
+ */
+#define SEAD3_SD_SPDCNF				0xbb000040
+#define SEAD3_SD_SPADDR				0xbb000048
+#define SEAD3_SD_DATA				0xbb000050
+
+/*
+ * Target #1 Register Decode
+ */
+#define SEAD3_CFG				0xbb100110
+#define SEAD3_GIC_BASE_ADDRESS			0xbb1c0000
+#define SEAD3_SHARED_SECTION			0xbb1c0000
+#define SEAD3_VPE_LOCAL_SECTION			0xbb1c8000
+#define SEAD3_VPE_OTHER_SECTION			0xbb1cc000
+#define SEAD3_USER_MODE_VISIBLE_SECTION		0xbb1d0000
+
+/*
+ * Target #3 Register Decode
+ */
+#define SEAD3_USB_HS_BASE			0xbb200000
+#define SEAD3_USB_HS_IDENTIFICATION_REGS	0xbb200000
+#define SEAD3_USB_HS_CAPABILITY_REGS		0xbb200100
+#define SEAD3_USB_HS_OPERATIONAL_REGS		0xbb200140
+#define SEAD3_RESERVED				0xbe800000
+
+/*
+ * Target #3 Register Decode
+ */
+#define SEAD3_SRAM				0xbe000000
+#define SEAD3_OPTIONAL_SRAM			0xbe400000
+#define SEAD3_FPGA				0xbf000000
+
+#define SEAD3_PI_PIC32_USB_STATUS		0xbf000060
+#define   SEAD3_PI_PIC32_USB_STATUS_IO_RDY	(1 << 0)
+#define   SEAD3_PI_PIC32_USB_STATUS_SPL_INT	(1 << 1)
+#define   SEAD3_PI_PIC32_USB_STATUS_GPIOA_INT	(1 << 2)
+#define   SEAD3_PI_PIC32_USB_STATUS_GPIOB_INT	(1 << 3)
+
+#define SEAD3_PI_SOFT_ENDIAN			0xbf000070
+
+#define SEAD3_CPLD_P_SWITCH			0xbf000200
+#define SEAD3_CPLD_F_SWITCH			0xbf000208
+#define SEAD3_CPLD_P_LED			0xbf000210
+#define SEAD3_CPLD_F_LED			0xbf000218
+#define SEAD3_NEWSC_LIVE			0xbf000220
+#define SEAD3_NEWSC_REG				0xbf000228
+#define SEAD3_NEWSC_CTRL			0xbf000230
+
+#define SEAD3_LCD_CONTROL			0xbf000400
+#define SEAD3_LCD_DATA				0xbf000408
+#define SEAD3_CPLD_LCD_STATUS			0xbf000410
+#define SEAD3_CPLD_LCD_DATA			0xbf000418
+
+#define SEAD3_CPLD_PI_DEVRST			0xbf000480
+#define SEAD3_CPLD_PI_DEVRST_IC32_RST		(1 << 0)
+#define SEAD3_RESERVED_0			0xbf000500
+
+#define SEAD3_PIC32_REGISTERS			0xbf000600
+#define SEAD3_RESERVED_1			0xbf000700
+#define SEAD3_UART_CH_0				0xbf000800
+#define SEAD3_UART_CH_1				0xbf000900
+#define SEAD3_RESERVED_2			0xbf000a00
+#define SEAD3_ETHERNET				0xbf010000
+#define SEAD3_RESERVED_3			0xbf020000
+#define SEAD3_USER_EXPANSION			0xbf400000
+#define SEAD3_RESERVED_4			0xbf800000
+#define SEAD3_BOOT_FLASH_EXTENSION		0xbfa00000
+#define SEAD3_BOOT_FLASH			0xbfc00000
+#define SEAD3_REVISION_REGISTER			0xbfc00010
+
+#endif /* __ASM_MIPS_BOARDS_SEAD3_ADDR_H  */
diff --git a/arch/mips/include/asm/mips-boards/sim.h b/arch/mips/include/asm/mips-boards/sim.h
new file mode 100644
index 000000000..ca37a4f32
--- /dev/null
+++ b/arch/mips/include/asm/mips-boards/sim.h
@@ -0,0 +1,27 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (C) 2005 MIPS Technologies, Inc.  All rights reserved.
+ */
+
+#ifndef _ASM_MIPS_BOARDS_SIM_H
+#define _ASM_MIPS_BOARDS_SIM_H
+
+#define STATS_ON	1
+#define STATS_OFF	2
+#define STATS_CLEAR	3
+#define STATS_DUMP	4
+#define TRACE_ON		5
+#define TRACE_OFF	6
+
+
+#define simcfg(code)						\
+({					   \
+	__asm__	 __volatile__( \
+	"sltiu $0,$0, %0" \
+		::"i"(code)					\
+		); \
+})
+
+
+
+#endif
diff --git a/arch/mips/include/asm/mips-cm.h b/arch/mips/include/asm/mips-cm.h
new file mode 100644
index 000000000..23c67c087
--- /dev/null
+++ b/arch/mips/include/asm/mips-cm.h
@@ -0,0 +1,459 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2013 Imagination Technologies
+ * Author: Paul Burton <paul.burton@mips.com>
+ */
+
+#ifndef __MIPS_ASM_MIPS_CPS_H__
+# error Please include asm/mips-cps.h rather than asm/mips-cm.h
+#endif
+
+#ifndef __MIPS_ASM_MIPS_CM_H__
+#define __MIPS_ASM_MIPS_CM_H__
+
+#include <linux/bitfield.h>
+#include <linux/bitops.h>
+#include <linux/errno.h>
+
+/* The base address of the CM GCR block */
+extern void __iomem *mips_gcr_base;
+
+/* The base address of the CM L2-only sync region */
+extern void __iomem *mips_cm_l2sync_base;
+
+/**
+ * __mips_cm_phys_base - retrieve the physical base address of the CM
+ *
+ * This function returns the physical base address of the Coherence Manager
+ * global control block, or 0 if no Coherence Manager is present. It provides
+ * a default implementation which reads the CMGCRBase register where available,
+ * and may be overridden by platforms which determine this address in a
+ * different way by defining a function with the same prototype except for the
+ * name mips_cm_phys_base (without underscores).
+ */
+extern phys_addr_t __mips_cm_phys_base(void);
+
+/*
+ * mips_cm_is64 - determine CM register width
+ *
+ * The CM register width is determined by the version of the CM, with CM3
+ * introducing 64 bit GCRs and all prior CM versions having 32 bit GCRs.
+ * However we may run a kernel built for MIPS32 on a system with 64 bit GCRs,
+ * or vice-versa. This variable indicates the width of the memory accesses
+ * that the kernel will perform to GCRs, which may differ from the actual
+ * width of the GCRs.
+ *
+ * It's set to 0 for 32-bit accesses and 1 for 64-bit accesses.
+ */
+extern int mips_cm_is64;
+
+/**
+ * mips_cm_error_report - Report CM cache errors
+ */
+#ifdef CONFIG_MIPS_CM
+extern void mips_cm_error_report(void);
+#else
+static inline void mips_cm_error_report(void) {}
+#endif
+
+/**
+ * mips_cm_probe - probe for a Coherence Manager
+ *
+ * Attempt to detect the presence of a Coherence Manager. Returns 0 if a CM
+ * is successfully detected, else -errno.
+ */
+#ifdef CONFIG_MIPS_CM
+extern int mips_cm_probe(void);
+#else
+static inline int mips_cm_probe(void)
+{
+	return -ENODEV;
+}
+#endif
+
+/**
+ * mips_cm_present - determine whether a Coherence Manager is present
+ *
+ * Returns true if a CM is present in the system, else false.
+ */
+static inline bool mips_cm_present(void)
+{
+#ifdef CONFIG_MIPS_CM
+	return mips_gcr_base != NULL;
+#else
+	return false;
+#endif
+}
+
+/**
+ * mips_cm_has_l2sync - determine whether an L2-only sync region is present
+ *
+ * Returns true if the system implements an L2-only sync region, else false.
+ */
+static inline bool mips_cm_has_l2sync(void)
+{
+#ifdef CONFIG_MIPS_CM
+	return mips_cm_l2sync_base != NULL;
+#else
+	return false;
+#endif
+}
+
+/* Offsets to register blocks from the CM base address */
+#define MIPS_CM_GCB_OFS		0x0000 /* Global Control Block */
+#define MIPS_CM_CLCB_OFS	0x2000 /* Core Local Control Block */
+#define MIPS_CM_COCB_OFS	0x4000 /* Core Other Control Block */
+#define MIPS_CM_GDB_OFS		0x6000 /* Global Debug Block */
+
+/* Total size of the CM memory mapped registers */
+#define MIPS_CM_GCR_SIZE	0x8000
+
+/* Size of the L2-only sync region */
+#define MIPS_CM_L2SYNC_SIZE	0x1000
+
+#define GCR_ACCESSOR_RO(sz, off, name)					\
+	CPS_ACCESSOR_RO(gcr, sz, MIPS_CM_GCB_OFS + off, name)		\
+	CPS_ACCESSOR_RO(gcr, sz, MIPS_CM_COCB_OFS + off, redir_##name)
+
+#define GCR_ACCESSOR_RW(sz, off, name)					\
+	CPS_ACCESSOR_RW(gcr, sz, MIPS_CM_GCB_OFS + off, name)		\
+	CPS_ACCESSOR_RW(gcr, sz, MIPS_CM_COCB_OFS + off, redir_##name)
+
+#define GCR_CX_ACCESSOR_RO(sz, off, name)				\
+	CPS_ACCESSOR_RO(gcr, sz, MIPS_CM_CLCB_OFS + off, cl_##name)	\
+	CPS_ACCESSOR_RO(gcr, sz, MIPS_CM_COCB_OFS + off, co_##name)
+
+#define GCR_CX_ACCESSOR_RW(sz, off, name)				\
+	CPS_ACCESSOR_RW(gcr, sz, MIPS_CM_CLCB_OFS + off, cl_##name)	\
+	CPS_ACCESSOR_RW(gcr, sz, MIPS_CM_COCB_OFS + off, co_##name)
+
+/* GCR_CONFIG - Information about the system */
+GCR_ACCESSOR_RO(64, 0x000, config)
+#define CM_GCR_CONFIG_CLUSTER_COH_CAPABLE	BIT_ULL(43)
+#define CM_GCR_CONFIG_CLUSTER_ID		GENMASK_ULL(39, 32)
+#define CM_GCR_CONFIG_NUM_CLUSTERS		GENMASK(29, 23)
+#define CM_GCR_CONFIG_NUMIOCU			GENMASK(15, 8)
+#define CM_GCR_CONFIG_PCORES			GENMASK(7, 0)
+
+/* GCR_BASE - Base address of the Global Configuration Registers (GCRs) */
+GCR_ACCESSOR_RW(64, 0x008, base)
+#define CM_GCR_BASE_GCRBASE			GENMASK_ULL(47, 15)
+#define CM_GCR_BASE_CMDEFTGT			GENMASK(1, 0)
+#define  CM_GCR_BASE_CMDEFTGT_MEM		0
+#define  CM_GCR_BASE_CMDEFTGT_RESERVED		1
+#define  CM_GCR_BASE_CMDEFTGT_IOCU0		2
+#define  CM_GCR_BASE_CMDEFTGT_IOCU1		3
+
+/* GCR_ACCESS - Controls core/IOCU access to GCRs */
+GCR_ACCESSOR_RW(32, 0x020, access)
+#define CM_GCR_ACCESS_ACCESSEN			GENMASK(7, 0)
+
+/* GCR_REV - Indicates the Coherence Manager revision */
+GCR_ACCESSOR_RO(32, 0x030, rev)
+#define CM_GCR_REV_MAJOR			GENMASK(15, 8)
+#define CM_GCR_REV_MINOR			GENMASK(7, 0)
+
+#define CM_ENCODE_REV(major, minor) \
+		(FIELD_PREP(CM_GCR_REV_MAJOR, major) | \
+		 FIELD_PREP(CM_GCR_REV_MINOR, minor))
+
+#define CM_REV_CM2				CM_ENCODE_REV(6, 0)
+#define CM_REV_CM2_5				CM_ENCODE_REV(7, 0)
+#define CM_REV_CM3				CM_ENCODE_REV(8, 0)
+#define CM_REV_CM3_5				CM_ENCODE_REV(9, 0)
+
+/* GCR_ERR_CONTROL - Control error checking logic */
+GCR_ACCESSOR_RW(32, 0x038, err_control)
+#define CM_GCR_ERR_CONTROL_L2_ECC_EN		BIT(1)
+#define CM_GCR_ERR_CONTROL_L2_ECC_SUPPORT	BIT(0)
+
+/* GCR_ERR_MASK - Control which errors are reported as interrupts */
+GCR_ACCESSOR_RW(64, 0x040, error_mask)
+
+/* GCR_ERR_CAUSE - Indicates the type of error that occurred */
+GCR_ACCESSOR_RW(64, 0x048, error_cause)
+#define CM_GCR_ERROR_CAUSE_ERRTYPE		GENMASK(31, 27)
+#define CM3_GCR_ERROR_CAUSE_ERRTYPE		GENMASK_ULL(63, 58)
+#define CM_GCR_ERROR_CAUSE_ERRINFO		GENMASK(26, 0)
+
+/* GCR_ERR_ADDR - Indicates the address associated with an error */
+GCR_ACCESSOR_RW(64, 0x050, error_addr)
+
+/* GCR_ERR_MULT - Indicates when multiple errors have occurred */
+GCR_ACCESSOR_RW(64, 0x058, error_mult)
+#define CM_GCR_ERROR_MULT_ERR2ND		GENMASK(4, 0)
+
+/* GCR_L2_ONLY_SYNC_BASE - Base address of the L2 cache-only sync region */
+GCR_ACCESSOR_RW(64, 0x070, l2_only_sync_base)
+#define CM_GCR_L2_ONLY_SYNC_BASE_SYNCBASE	GENMASK(31, 12)
+#define CM_GCR_L2_ONLY_SYNC_BASE_SYNCEN		BIT(0)
+
+/* GCR_GIC_BASE - Base address of the Global Interrupt Controller (GIC) */
+GCR_ACCESSOR_RW(64, 0x080, gic_base)
+#define CM_GCR_GIC_BASE_GICBASE			GENMASK(31, 17)
+#define CM_GCR_GIC_BASE_GICEN			BIT(0)
+
+/* GCR_CPC_BASE - Base address of the Cluster Power Controller (CPC) */
+GCR_ACCESSOR_RW(64, 0x088, cpc_base)
+#define CM_GCR_CPC_BASE_CPCBASE			GENMASK(31, 15)
+#define CM_GCR_CPC_BASE_CPCEN			BIT(0)
+
+/* GCR_REGn_BASE - Base addresses of CM address regions */
+GCR_ACCESSOR_RW(64, 0x090, reg0_base)
+GCR_ACCESSOR_RW(64, 0x0a0, reg1_base)
+GCR_ACCESSOR_RW(64, 0x0b0, reg2_base)
+GCR_ACCESSOR_RW(64, 0x0c0, reg3_base)
+#define CM_GCR_REGn_BASE_BASEADDR		GENMASK(31, 16)
+
+/* GCR_REGn_MASK - Size & destination of CM address regions */
+GCR_ACCESSOR_RW(64, 0x098, reg0_mask)
+GCR_ACCESSOR_RW(64, 0x0a8, reg1_mask)
+GCR_ACCESSOR_RW(64, 0x0b8, reg2_mask)
+GCR_ACCESSOR_RW(64, 0x0c8, reg3_mask)
+#define CM_GCR_REGn_MASK_ADDRMASK		GENMASK(31, 16)
+#define CM_GCR_REGn_MASK_CCAOVR			GENMASK(7, 5)
+#define CM_GCR_REGn_MASK_CCAOVREN		BIT(4)
+#define CM_GCR_REGn_MASK_DROPL2			BIT(2)
+#define CM_GCR_REGn_MASK_CMTGT			GENMASK(1, 0)
+#define  CM_GCR_REGn_MASK_CMTGT_DISABLED	0x0
+#define  CM_GCR_REGn_MASK_CMTGT_MEM		0x1
+#define  CM_GCR_REGn_MASK_CMTGT_IOCU0		0x2
+#define  CM_GCR_REGn_MASK_CMTGT_IOCU1		0x3
+
+/* GCR_GIC_STATUS - Indicates presence of a Global Interrupt Controller (GIC) */
+GCR_ACCESSOR_RO(32, 0x0d0, gic_status)
+#define CM_GCR_GIC_STATUS_EX			BIT(0)
+
+/* GCR_CPC_STATUS - Indicates presence of a Cluster Power Controller (CPC) */
+GCR_ACCESSOR_RO(32, 0x0f0, cpc_status)
+#define CM_GCR_CPC_STATUS_EX			BIT(0)
+
+/* GCR_L2_CONFIG - Indicates L2 cache configuration when Config5.L2C=1 */
+GCR_ACCESSOR_RW(32, 0x130, l2_config)
+#define CM_GCR_L2_CONFIG_BYPASS			BIT(20)
+#define CM_GCR_L2_CONFIG_SET_SIZE		GENMASK(15, 12)
+#define CM_GCR_L2_CONFIG_LINE_SIZE		GENMASK(11, 8)
+#define CM_GCR_L2_CONFIG_ASSOC			GENMASK(7, 0)
+
+/* GCR_SYS_CONFIG2 - Further information about the system */
+GCR_ACCESSOR_RO(32, 0x150, sys_config2)
+#define CM_GCR_SYS_CONFIG2_MAXVPW		GENMASK(3, 0)
+
+/* GCR_L2_PFT_CONTROL - Controls hardware L2 prefetching */
+GCR_ACCESSOR_RW(32, 0x300, l2_pft_control)
+#define CM_GCR_L2_PFT_CONTROL_PAGEMASK		GENMASK(31, 12)
+#define CM_GCR_L2_PFT_CONTROL_PFTEN		BIT(8)
+#define CM_GCR_L2_PFT_CONTROL_NPFT		GENMASK(7, 0)
+
+/* GCR_L2_PFT_CONTROL_B - Controls hardware L2 prefetching */
+GCR_ACCESSOR_RW(32, 0x308, l2_pft_control_b)
+#define CM_GCR_L2_PFT_CONTROL_B_CEN		BIT(8)
+#define CM_GCR_L2_PFT_CONTROL_B_PORTID		GENMASK(7, 0)
+
+/* GCR_L2SM_COP - L2 cache op state machine control */
+GCR_ACCESSOR_RW(32, 0x620, l2sm_cop)
+#define CM_GCR_L2SM_COP_PRESENT			BIT(31)
+#define CM_GCR_L2SM_COP_RESULT			GENMASK(8, 6)
+#define  CM_GCR_L2SM_COP_RESULT_DONTCARE	0
+#define  CM_GCR_L2SM_COP_RESULT_DONE_OK		1
+#define  CM_GCR_L2SM_COP_RESULT_DONE_ERROR	2
+#define  CM_GCR_L2SM_COP_RESULT_ABORT_OK	3
+#define  CM_GCR_L2SM_COP_RESULT_ABORT_ERROR	4
+#define CM_GCR_L2SM_COP_RUNNING			BIT(5)
+#define CM_GCR_L2SM_COP_TYPE			GENMASK(4, 2)
+#define  CM_GCR_L2SM_COP_TYPE_IDX_WBINV		0
+#define  CM_GCR_L2SM_COP_TYPE_IDX_STORETAG	1
+#define  CM_GCR_L2SM_COP_TYPE_IDX_STORETAGDATA	2
+#define  CM_GCR_L2SM_COP_TYPE_HIT_INV		4
+#define  CM_GCR_L2SM_COP_TYPE_HIT_WBINV		5
+#define  CM_GCR_L2SM_COP_TYPE_HIT_WB		6
+#define  CM_GCR_L2SM_COP_TYPE_FETCHLOCK		7
+#define CM_GCR_L2SM_COP_CMD			GENMASK(1, 0)
+#define  CM_GCR_L2SM_COP_CMD_START		1	/* only when idle */
+#define  CM_GCR_L2SM_COP_CMD_ABORT		3	/* only when running */
+
+/* GCR_L2SM_TAG_ADDR_COP - L2 cache op state machine address control */
+GCR_ACCESSOR_RW(64, 0x628, l2sm_tag_addr_cop)
+#define CM_GCR_L2SM_TAG_ADDR_COP_NUM_LINES	GENMASK_ULL(63, 48)
+#define CM_GCR_L2SM_TAG_ADDR_COP_START_TAG	GENMASK_ULL(47, 6)
+
+/* GCR_BEV_BASE - Controls the location of the BEV for powered up cores */
+GCR_ACCESSOR_RW(64, 0x680, bev_base)
+
+/* GCR_Cx_RESET_RELEASE - Controls core reset for CM 1.x */
+GCR_CX_ACCESSOR_RW(32, 0x000, reset_release)
+
+/* GCR_Cx_COHERENCE - Controls core coherence */
+GCR_CX_ACCESSOR_RW(32, 0x008, coherence)
+#define CM_GCR_Cx_COHERENCE_COHDOMAINEN		GENMASK(7, 0)
+#define CM3_GCR_Cx_COHERENCE_COHEN		BIT(0)
+
+/* GCR_Cx_CONFIG - Information about a core's configuration */
+GCR_CX_ACCESSOR_RO(32, 0x010, config)
+#define CM_GCR_Cx_CONFIG_IOCUTYPE		GENMASK(11, 10)
+#define CM_GCR_Cx_CONFIG_PVPE			GENMASK(9, 0)
+
+/* GCR_Cx_OTHER - Configure the core-other/redirect GCR block */
+GCR_CX_ACCESSOR_RW(32, 0x018, other)
+#define CM_GCR_Cx_OTHER_CORENUM			GENMASK(31, 16)	/* CM < 3 */
+#define CM_GCR_Cx_OTHER_CLUSTER_EN		BIT(31)		/* CM >= 3.5 */
+#define CM_GCR_Cx_OTHER_GIC_EN			BIT(30)		/* CM >= 3.5 */
+#define CM_GCR_Cx_OTHER_BLOCK			GENMASK(25, 24)	/* CM >= 3.5 */
+#define  CM_GCR_Cx_OTHER_BLOCK_LOCAL		0
+#define  CM_GCR_Cx_OTHER_BLOCK_GLOBAL		1
+#define  CM_GCR_Cx_OTHER_BLOCK_USER		2
+#define  CM_GCR_Cx_OTHER_BLOCK_GLOBAL_HIGH	3
+#define CM_GCR_Cx_OTHER_CLUSTER			GENMASK(21, 16)	/* CM >= 3.5 */
+#define CM3_GCR_Cx_OTHER_CORE			GENMASK(13, 8)	/* CM >= 3 */
+#define  CM_GCR_Cx_OTHER_CORE_CM		32
+#define CM3_GCR_Cx_OTHER_VP			GENMASK(2, 0)	/* CM >= 3 */
+
+/* GCR_Cx_RESET_BASE - Configure where powered up cores will fetch from */
+GCR_CX_ACCESSOR_RW(32, 0x020, reset_base)
+#define CM_GCR_Cx_RESET_BASE_BEVEXCBASE		GENMASK(31, 12)
+
+/* GCR_Cx_ID - Identify the current core */
+GCR_CX_ACCESSOR_RO(32, 0x028, id)
+#define CM_GCR_Cx_ID_CLUSTER			GENMASK(15, 8)
+#define CM_GCR_Cx_ID_CORE			GENMASK(7, 0)
+
+/* GCR_Cx_RESET_EXT_BASE - Configure behaviour when cores reset or power up */
+GCR_CX_ACCESSOR_RW(32, 0x030, reset_ext_base)
+#define CM_GCR_Cx_RESET_EXT_BASE_EVARESET	BIT(31)
+#define CM_GCR_Cx_RESET_EXT_BASE_UEB		BIT(30)
+#define CM_GCR_Cx_RESET_EXT_BASE_BEVEXCMASK	GENMASK(27, 20)
+#define CM_GCR_Cx_RESET_EXT_BASE_BEVEXCPA	GENMASK(7, 1)
+#define CM_GCR_Cx_RESET_EXT_BASE_PRESENT	BIT(0)
+
+/**
+ * mips_cm_l2sync - perform an L2-only sync operation
+ *
+ * If an L2-only sync region is present in the system then this function
+ * performs and L2-only sync and returns zero. Otherwise it returns -ENODEV.
+ */
+static inline int mips_cm_l2sync(void)
+{
+	if (!mips_cm_has_l2sync())
+		return -ENODEV;
+
+	writel(0, mips_cm_l2sync_base);
+	return 0;
+}
+
+/**
+ * mips_cm_revision() - return CM revision
+ *
+ * Return: The revision of the CM, from GCR_REV, or 0 if no CM is present. The
+ * return value should be checked against the CM_REV_* macros.
+ */
+static inline int mips_cm_revision(void)
+{
+	if (!mips_cm_present())
+		return 0;
+
+	return read_gcr_rev();
+}
+
+/**
+ * mips_cm_max_vp_width() - return the width in bits of VP indices
+ *
+ * Return: the width, in bits, of VP indices in fields that combine core & VP
+ * indices.
+ */
+static inline unsigned int mips_cm_max_vp_width(void)
+{
+	extern int smp_num_siblings;
+
+	if (mips_cm_revision() >= CM_REV_CM3)
+		return FIELD_GET(CM_GCR_SYS_CONFIG2_MAXVPW,
+				 read_gcr_sys_config2());
+
+	if (mips_cm_present()) {
+		/*
+		 * We presume that all cores in the system will have the same
+		 * number of VP(E)s, and if that ever changes then this will
+		 * need revisiting.
+		 */
+		return FIELD_GET(CM_GCR_Cx_CONFIG_PVPE, read_gcr_cl_config()) + 1;
+	}
+
+	if (IS_ENABLED(CONFIG_SMP))
+		return smp_num_siblings;
+
+	return 1;
+}
+
+/**
+ * mips_cm_vp_id() - calculate the hardware VP ID for a CPU
+ * @cpu: the CPU whose VP ID to calculate
+ *
+ * Hardware such as the GIC uses identifiers for VPs which may not match the
+ * CPU numbers used by Linux. This function calculates the hardware VP
+ * identifier corresponding to a given CPU.
+ *
+ * Return: the VP ID for the CPU.
+ */
+static inline unsigned int mips_cm_vp_id(unsigned int cpu)
+{
+	unsigned int core = cpu_core(&cpu_data[cpu]);
+	unsigned int vp = cpu_vpe_id(&cpu_data[cpu]);
+
+	return (core * mips_cm_max_vp_width()) + vp;
+}
+
+#ifdef CONFIG_MIPS_CM
+
+/**
+ * mips_cm_lock_other - lock access to redirect/other region
+ * @cluster: the other cluster to be accessed
+ * @core: the other core to be accessed
+ * @vp: the VP within the other core to be accessed
+ * @block: the register block to be accessed
+ *
+ * Configure the redirect/other region for the local core/VP (depending upon
+ * the CM revision) to target the specified @cluster, @core, @vp & register
+ * @block. Must be called before using the redirect/other region, and followed
+ * by a call to mips_cm_unlock_other() when access to the redirect/other region
+ * is complete.
+ *
+ * This function acquires a spinlock such that code between it &
+ * mips_cm_unlock_other() calls cannot be pre-empted by anything which may
+ * reconfigure the redirect/other region, and cannot be interfered with by
+ * another VP in the core. As such calls to this function should not be nested.
+ */
+extern void mips_cm_lock_other(unsigned int cluster, unsigned int core,
+			       unsigned int vp, unsigned int block);
+
+/**
+ * mips_cm_unlock_other - unlock access to redirect/other region
+ *
+ * Must be called after mips_cm_lock_other() once all required access to the
+ * redirect/other region has been completed.
+ */
+extern void mips_cm_unlock_other(void);
+
+#else /* !CONFIG_MIPS_CM */
+
+static inline void mips_cm_lock_other(unsigned int cluster, unsigned int core,
+				      unsigned int vp, unsigned int block) { }
+static inline void mips_cm_unlock_other(void) { }
+
+#endif /* !CONFIG_MIPS_CM */
+
+/**
+ * mips_cm_lock_other_cpu - lock access to redirect/other region
+ * @cpu: the other CPU whose register we want to access
+ *
+ * Configure the redirect/other region for the local core/VP (depending upon
+ * the CM revision) to target the specified @cpu & register @block. This is
+ * equivalent to calling mips_cm_lock_other() but accepts a Linux CPU number
+ * for convenience.
+ */
+static inline void mips_cm_lock_other_cpu(unsigned int cpu, unsigned int block)
+{
+	struct cpuinfo_mips *d = &cpu_data[cpu];
+
+	mips_cm_lock_other(cpu_cluster(d), cpu_core(d), cpu_vpe_id(d), block);
+}
+
+#endif /* __MIPS_ASM_MIPS_CM_H__ */
diff --git a/arch/mips/include/asm/mips-cpc.h b/arch/mips/include/asm/mips-cpc.h
new file mode 100644
index 000000000..b54453f16
--- /dev/null
+++ b/arch/mips/include/asm/mips-cpc.h
@@ -0,0 +1,179 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2013 Imagination Technologies
+ * Author: Paul Burton <paul.burton@mips.com>
+ */
+
+#ifndef __MIPS_ASM_MIPS_CPS_H__
+# error Please include asm/mips-cps.h rather than asm/mips-cpc.h
+#endif
+
+#ifndef __MIPS_ASM_MIPS_CPC_H__
+#define __MIPS_ASM_MIPS_CPC_H__
+
+#include <linux/bitops.h>
+#include <linux/errno.h>
+
+/* The base address of the CPC registers */
+extern void __iomem *mips_cpc_base;
+
+/**
+ * mips_cpc_default_phys_base - retrieve the default physical base address of
+ *                              the CPC
+ *
+ * Returns the default physical base address of the Cluster Power Controller
+ * memory mapped registers. This is platform dependant & must therefore be
+ * implemented per-platform.
+ */
+extern phys_addr_t mips_cpc_default_phys_base(void);
+
+/**
+ * mips_cpc_probe - probe for a Cluster Power Controller
+ *
+ * Attempt to detect the presence of a Cluster Power Controller. Returns 0 if
+ * a CPC is successfully detected, else -errno.
+ */
+#ifdef CONFIG_MIPS_CPC
+extern int mips_cpc_probe(void);
+#else
+static inline int mips_cpc_probe(void)
+{
+	return -ENODEV;
+}
+#endif
+
+/**
+ * mips_cpc_present - determine whether a Cluster Power Controller is present
+ *
+ * Returns true if a CPC is present in the system, else false.
+ */
+static inline bool mips_cpc_present(void)
+{
+#ifdef CONFIG_MIPS_CPC
+	return mips_cpc_base != NULL;
+#else
+	return false;
+#endif
+}
+
+/* Offsets from the CPC base address to various control blocks */
+#define MIPS_CPC_GCB_OFS	0x0000
+#define MIPS_CPC_CLCB_OFS	0x2000
+#define MIPS_CPC_COCB_OFS	0x4000
+
+#define CPC_ACCESSOR_RO(sz, off, name)					\
+	CPS_ACCESSOR_RO(cpc, sz, MIPS_CPC_GCB_OFS + off, name)		\
+	CPS_ACCESSOR_RO(cpc, sz, MIPS_CPC_COCB_OFS + off, redir_##name)
+
+#define CPC_ACCESSOR_RW(sz, off, name)					\
+	CPS_ACCESSOR_RW(cpc, sz, MIPS_CPC_GCB_OFS + off, name)		\
+	CPS_ACCESSOR_RW(cpc, sz, MIPS_CPC_COCB_OFS + off, redir_##name)
+
+#define CPC_CX_ACCESSOR_RO(sz, off, name)				\
+	CPS_ACCESSOR_RO(cpc, sz, MIPS_CPC_CLCB_OFS + off, cl_##name)	\
+	CPS_ACCESSOR_RO(cpc, sz, MIPS_CPC_COCB_OFS + off, co_##name)
+
+#define CPC_CX_ACCESSOR_RW(sz, off, name)				\
+	CPS_ACCESSOR_RW(cpc, sz, MIPS_CPC_CLCB_OFS + off, cl_##name)	\
+	CPS_ACCESSOR_RW(cpc, sz, MIPS_CPC_COCB_OFS + off, co_##name)
+
+/* CPC_ACCESS - Control core/IOCU access to CPC registers prior to CM 3 */
+CPC_ACCESSOR_RW(32, 0x000, access)
+
+/* CPC_SEQDEL - Configure delays between command sequencer steps */
+CPC_ACCESSOR_RW(32, 0x008, seqdel)
+
+/* CPC_RAIL - Configure the delay from rail power-up to stability */
+CPC_ACCESSOR_RW(32, 0x010, rail)
+
+/* CPC_RESETLEN - Configure the length of reset sequences */
+CPC_ACCESSOR_RW(32, 0x018, resetlen)
+
+/* CPC_REVISION - Indicates the revisison of the CPC */
+CPC_ACCESSOR_RO(32, 0x020, revision)
+
+/* CPC_PWRUP_CTL - Control power to the Coherence Manager (CM) */
+CPC_ACCESSOR_RW(32, 0x030, pwrup_ctl)
+#define CPC_PWRUP_CTL_CM_PWRUP			BIT(0)
+
+/* CPC_CONFIG - Mirrors GCR_CONFIG */
+CPC_ACCESSOR_RW(64, 0x138, config)
+
+/* CPC_SYS_CONFIG - Control cluster endianness */
+CPC_ACCESSOR_RW(32, 0x140, sys_config)
+#define CPC_SYS_CONFIG_BE_IMMEDIATE		BIT(2)
+#define CPC_SYS_CONFIG_BE_STATUS		BIT(1)
+#define CPC_SYS_CONFIG_BE			BIT(0)
+
+/* CPC_Cx_CMD - Instruct the CPC to take action on a core */
+CPC_CX_ACCESSOR_RW(32, 0x000, cmd)
+#define CPC_Cx_CMD				GENMASK(3, 0)
+#define  CPC_Cx_CMD_CLOCKOFF			0x1
+#define  CPC_Cx_CMD_PWRDOWN			0x2
+#define  CPC_Cx_CMD_PWRUP			0x3
+#define  CPC_Cx_CMD_RESET			0x4
+
+/* CPC_Cx_STAT_CONF - Indicates core configuration & state */
+CPC_CX_ACCESSOR_RW(32, 0x008, stat_conf)
+#define CPC_Cx_STAT_CONF_PWRUPE			BIT(23)
+#define CPC_Cx_STAT_CONF_SEQSTATE		GENMASK(22, 19)
+#define  CPC_Cx_STAT_CONF_SEQSTATE_D0		0x0
+#define  CPC_Cx_STAT_CONF_SEQSTATE_U0		0x1
+#define  CPC_Cx_STAT_CONF_SEQSTATE_U1		0x2
+#define  CPC_Cx_STAT_CONF_SEQSTATE_U2		0x3
+#define  CPC_Cx_STAT_CONF_SEQSTATE_U3		0x4
+#define  CPC_Cx_STAT_CONF_SEQSTATE_U4		0x5
+#define  CPC_Cx_STAT_CONF_SEQSTATE_U5		0x6
+#define  CPC_Cx_STAT_CONF_SEQSTATE_U6		0x7
+#define  CPC_Cx_STAT_CONF_SEQSTATE_D1		0x8
+#define  CPC_Cx_STAT_CONF_SEQSTATE_D3		0x9
+#define  CPC_Cx_STAT_CONF_SEQSTATE_D2		0xa
+#define CPC_Cx_STAT_CONF_CLKGAT_IMPL		BIT(17)
+#define CPC_Cx_STAT_CONF_PWRDN_IMPL		BIT(16)
+#define CPC_Cx_STAT_CONF_EJTAG_PROBE		BIT(15)
+
+/* CPC_Cx_OTHER - Configure the core-other register block prior to CM 3 */
+CPC_CX_ACCESSOR_RW(32, 0x010, other)
+#define CPC_Cx_OTHER_CORENUM			GENMASK(23, 16)
+
+/* CPC_Cx_VP_STOP - Stop Virtual Processors (VPs) within a core from running */
+CPC_CX_ACCESSOR_RW(32, 0x020, vp_stop)
+
+/* CPC_Cx_VP_START - Start Virtual Processors (VPs) within a core running */
+CPC_CX_ACCESSOR_RW(32, 0x028, vp_run)
+
+/* CPC_Cx_VP_RUNNING - Indicate which Virtual Processors (VPs) are running */
+CPC_CX_ACCESSOR_RW(32, 0x030, vp_running)
+
+/* CPC_Cx_CONFIG - Mirrors GCR_Cx_CONFIG */
+CPC_CX_ACCESSOR_RW(32, 0x090, config)
+
+#ifdef CONFIG_MIPS_CPC
+
+/**
+ * mips_cpc_lock_other - lock access to another core
+ * core: the other core to be accessed
+ *
+ * Call before operating upon a core via the 'other' register region in
+ * order to prevent the region being moved during access. Must be called
+ * within the bounds of a mips_cm_{lock,unlock}_other pair, and followed
+ * by a call to mips_cpc_unlock_other.
+ */
+extern void mips_cpc_lock_other(unsigned int core);
+
+/**
+ * mips_cpc_unlock_other - unlock access to another core
+ *
+ * Call after operating upon another core via the 'other' register region.
+ * Must be called after mips_cpc_lock_other.
+ */
+extern void mips_cpc_unlock_other(void);
+
+#else /* !CONFIG_MIPS_CPC */
+
+static inline void mips_cpc_lock_other(unsigned int core) { }
+static inline void mips_cpc_unlock_other(void) { }
+
+#endif /* !CONFIG_MIPS_CPC */
+
+#endif /* __MIPS_ASM_MIPS_CPC_H__ */
diff --git a/arch/mips/include/asm/mips-cps.h b/arch/mips/include/asm/mips-cps.h
new file mode 100644
index 000000000..c077e8d10
--- /dev/null
+++ b/arch/mips/include/asm/mips-cps.h
@@ -0,0 +1,231 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2017 Imagination Technologies
+ * Author: Paul Burton <paul.burton@mips.com>
+ */
+
+#ifndef __MIPS_ASM_MIPS_CPS_H__
+#define __MIPS_ASM_MIPS_CPS_H__
+
+#include <linux/bitfield.h>
+#include <linux/io.h>
+#include <linux/types.h>
+
+extern unsigned long __cps_access_bad_size(void)
+	__compiletime_error("Bad size for CPS accessor");
+
+#define CPS_ACCESSOR_A(unit, off, name)					\
+static inline void *addr_##unit##_##name(void)				\
+{									\
+	return mips_##unit##_base + (off);				\
+}
+
+#define CPS_ACCESSOR_R(unit, sz, name)					\
+static inline uint##sz##_t read_##unit##_##name(void)			\
+{									\
+	uint64_t val64;							\
+									\
+	switch (sz) {							\
+	case 32:							\
+		return __raw_readl(addr_##unit##_##name());		\
+									\
+	case 64:							\
+		if (mips_cm_is64)					\
+			return __raw_readq(addr_##unit##_##name());	\
+									\
+		val64 = __raw_readl(addr_##unit##_##name() + 4);	\
+		val64 <<= 32;						\
+		val64 |= __raw_readl(addr_##unit##_##name());		\
+		return val64;						\
+									\
+	default:							\
+		return __cps_access_bad_size();				\
+	}								\
+}
+
+#define CPS_ACCESSOR_W(unit, sz, name)					\
+static inline void write_##unit##_##name(uint##sz##_t val)		\
+{									\
+	switch (sz) {							\
+	case 32:							\
+		__raw_writel(val, addr_##unit##_##name());		\
+		break;							\
+									\
+	case 64:							\
+		if (mips_cm_is64) {					\
+			__raw_writeq(val, addr_##unit##_##name());	\
+			break;						\
+		}							\
+									\
+		__raw_writel((uint64_t)val >> 32,			\
+			     addr_##unit##_##name() + 4);		\
+		__raw_writel(val, addr_##unit##_##name());		\
+		break;							\
+									\
+	default:							\
+		__cps_access_bad_size();				\
+		break;							\
+	}								\
+}
+
+#define CPS_ACCESSOR_M(unit, sz, name)					\
+static inline void change_##unit##_##name(uint##sz##_t mask,		\
+					  uint##sz##_t val)		\
+{									\
+	uint##sz##_t reg_val = read_##unit##_##name();			\
+	reg_val &= ~mask;						\
+	reg_val |= val;							\
+	write_##unit##_##name(reg_val);					\
+}									\
+									\
+static inline void set_##unit##_##name(uint##sz##_t val)		\
+{									\
+	change_##unit##_##name(val, val);				\
+}									\
+									\
+static inline void clear_##unit##_##name(uint##sz##_t val)		\
+{									\
+	change_##unit##_##name(val, 0);					\
+}
+
+#define CPS_ACCESSOR_RO(unit, sz, off, name)				\
+	CPS_ACCESSOR_A(unit, off, name)					\
+	CPS_ACCESSOR_R(unit, sz, name)
+
+#define CPS_ACCESSOR_WO(unit, sz, off, name)				\
+	CPS_ACCESSOR_A(unit, off, name)					\
+	CPS_ACCESSOR_W(unit, sz, name)
+
+#define CPS_ACCESSOR_RW(unit, sz, off, name)				\
+	CPS_ACCESSOR_A(unit, off, name)					\
+	CPS_ACCESSOR_R(unit, sz, name)					\
+	CPS_ACCESSOR_W(unit, sz, name)					\
+	CPS_ACCESSOR_M(unit, sz, name)
+
+#include <asm/mips-cm.h>
+#include <asm/mips-cpc.h>
+#include <asm/mips-gic.h>
+
+/**
+ * mips_cps_numclusters - return the number of clusters present in the system
+ *
+ * Returns the number of clusters in the system.
+ */
+static inline unsigned int mips_cps_numclusters(void)
+{
+	if (mips_cm_revision() < CM_REV_CM3_5)
+		return 1;
+
+	return FIELD_GET(CM_GCR_CONFIG_NUM_CLUSTERS, read_gcr_config());
+}
+
+/**
+ * mips_cps_cluster_config - return (GCR|CPC)_CONFIG from a cluster
+ * @cluster: the ID of the cluster whose config we want
+ *
+ * Read the value of GCR_CONFIG (or its CPC_CONFIG mirror) from a @cluster.
+ *
+ * Returns the value of GCR_CONFIG.
+ */
+static inline uint64_t mips_cps_cluster_config(unsigned int cluster)
+{
+	uint64_t config;
+
+	if (mips_cm_revision() < CM_REV_CM3_5) {
+		/*
+		 * Prior to CM 3.5 we don't have the notion of multiple
+		 * clusters so we can trivially read the GCR_CONFIG register
+		 * within this cluster.
+		 */
+		WARN_ON(cluster != 0);
+		config = read_gcr_config();
+	} else {
+		/*
+		 * From CM 3.5 onwards we read the CPC_CONFIG mirror of
+		 * GCR_CONFIG via the redirect region, since the CPC is always
+		 * powered up allowing us not to need to power up the CM.
+		 */
+		mips_cm_lock_other(cluster, 0, 0, CM_GCR_Cx_OTHER_BLOCK_GLOBAL);
+		config = read_cpc_redir_config();
+		mips_cm_unlock_other();
+	}
+
+	return config;
+}
+
+/**
+ * mips_cps_numcores - return the number of cores present in a cluster
+ * @cluster: the ID of the cluster whose core count we want
+ *
+ * Returns the value of the PCORES field of the GCR_CONFIG register plus 1, or
+ * zero if no Coherence Manager is present.
+ */
+static inline unsigned int mips_cps_numcores(unsigned int cluster)
+{
+	if (!mips_cm_present())
+		return 0;
+
+	/* Add one before masking to handle 0xff indicating no cores */
+	return FIELD_GET(CM_GCR_CONFIG_PCORES,
+			 mips_cps_cluster_config(cluster) + 1);
+}
+
+/**
+ * mips_cps_numiocu - return the number of IOCUs present in a cluster
+ * @cluster: the ID of the cluster whose IOCU count we want
+ *
+ * Returns the value of the NUMIOCU field of the GCR_CONFIG register, or zero
+ * if no Coherence Manager is present.
+ */
+static inline unsigned int mips_cps_numiocu(unsigned int cluster)
+{
+	if (!mips_cm_present())
+		return 0;
+
+	return FIELD_GET(CM_GCR_CONFIG_NUMIOCU,
+			 mips_cps_cluster_config(cluster));
+}
+
+/**
+ * mips_cps_numvps - return the number of VPs (threads) supported by a core
+ * @cluster: the ID of the cluster containing the core we want to examine
+ * @core: the ID of the core whose VP count we want
+ *
+ * Returns the number of Virtual Processors (VPs, ie. hardware threads) that
+ * are supported by the given @core in the given @cluster. If the core or the
+ * kernel do not support hardware mutlti-threading this returns 1.
+ */
+static inline unsigned int mips_cps_numvps(unsigned int cluster, unsigned int core)
+{
+	unsigned int cfg;
+
+	if (!mips_cm_present())
+		return 1;
+
+	if ((!IS_ENABLED(CONFIG_MIPS_MT_SMP) || !cpu_has_mipsmt)
+		&& (!IS_ENABLED(CONFIG_CPU_MIPSR6) || !cpu_has_vp))
+		return 1;
+
+	mips_cm_lock_other(cluster, core, 0, CM_GCR_Cx_OTHER_BLOCK_LOCAL);
+
+	if (mips_cm_revision() < CM_REV_CM3_5) {
+		/*
+		 * Prior to CM 3.5 we can only have one cluster & don't have
+		 * CPC_Cx_CONFIG, so we read GCR_Cx_CONFIG.
+		 */
+		cfg = read_gcr_co_config();
+	} else {
+		/*
+		 * From CM 3.5 onwards we read CPC_Cx_CONFIG because the CPC is
+		 * always powered, which allows us to not worry about powering
+		 * up the cluster's CM here.
+		 */
+		cfg = read_cpc_co_config();
+	}
+
+	mips_cm_unlock_other();
+
+	return FIELD_GET(CM_GCR_Cx_CONFIG_PVPE, cfg + 1);
+}
+
+#endif /* __MIPS_ASM_MIPS_CPS_H__ */
diff --git a/arch/mips/include/asm/mips-gic.h b/arch/mips/include/asm/mips-gic.h
new file mode 100644
index 000000000..084cac1c5
--- /dev/null
+++ b/arch/mips/include/asm/mips-gic.h
@@ -0,0 +1,373 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2017 Imagination Technologies
+ * Author: Paul Burton <paul.burton@mips.com>
+ */
+
+#ifndef __MIPS_ASM_MIPS_CPS_H__
+# error Please include asm/mips-cps.h rather than asm/mips-gic.h
+#endif
+
+#ifndef __MIPS_ASM_MIPS_GIC_H__
+#define __MIPS_ASM_MIPS_GIC_H__
+
+#include <linux/bitops.h>
+
+/* The base address of the GIC registers */
+extern void __iomem *mips_gic_base;
+
+/* Offsets from the GIC base address to various control blocks */
+#define MIPS_GIC_SHARED_OFS	0x00000
+#define MIPS_GIC_SHARED_SZ	0x08000
+#define MIPS_GIC_LOCAL_OFS	0x08000
+#define MIPS_GIC_LOCAL_SZ	0x04000
+#define MIPS_GIC_REDIR_OFS	0x0c000
+#define MIPS_GIC_REDIR_SZ	0x04000
+#define MIPS_GIC_USER_OFS	0x10000
+#define MIPS_GIC_USER_SZ	0x10000
+
+/* For read-only shared registers */
+#define GIC_ACCESSOR_RO(sz, off, name)					\
+	CPS_ACCESSOR_RO(gic, sz, MIPS_GIC_SHARED_OFS + off, name)
+
+/* For read-write shared registers */
+#define GIC_ACCESSOR_RW(sz, off, name)					\
+	CPS_ACCESSOR_RW(gic, sz, MIPS_GIC_SHARED_OFS + off, name)
+
+/* For read-only local registers */
+#define GIC_VX_ACCESSOR_RO(sz, off, name)				\
+	CPS_ACCESSOR_RO(gic, sz, MIPS_GIC_LOCAL_OFS + off, vl_##name)	\
+	CPS_ACCESSOR_RO(gic, sz, MIPS_GIC_REDIR_OFS + off, vo_##name)
+
+/* For read-write local registers */
+#define GIC_VX_ACCESSOR_RW(sz, off, name)				\
+	CPS_ACCESSOR_RW(gic, sz, MIPS_GIC_LOCAL_OFS + off, vl_##name)	\
+	CPS_ACCESSOR_RW(gic, sz, MIPS_GIC_REDIR_OFS + off, vo_##name)
+
+/* For read-only shared per-interrupt registers */
+#define GIC_ACCESSOR_RO_INTR_REG(sz, off, stride, name)			\
+static inline void __iomem *addr_gic_##name(unsigned int intr)		\
+{									\
+	return mips_gic_base + (off) + (intr * (stride));		\
+}									\
+									\
+static inline unsigned int read_gic_##name(unsigned int intr)		\
+{									\
+	BUILD_BUG_ON(sz != 32);						\
+	return __raw_readl(addr_gic_##name(intr));			\
+}
+
+/* For read-write shared per-interrupt registers */
+#define GIC_ACCESSOR_RW_INTR_REG(sz, off, stride, name)			\
+	GIC_ACCESSOR_RO_INTR_REG(sz, off, stride, name)			\
+									\
+static inline void write_gic_##name(unsigned int intr,			\
+				    unsigned int val)			\
+{									\
+	BUILD_BUG_ON(sz != 32);						\
+	__raw_writel(val, addr_gic_##name(intr));			\
+}
+
+/* For read-only local per-interrupt registers */
+#define GIC_VX_ACCESSOR_RO_INTR_REG(sz, off, stride, name)		\
+	GIC_ACCESSOR_RO_INTR_REG(sz, MIPS_GIC_LOCAL_OFS + off,		\
+				 stride, vl_##name)			\
+	GIC_ACCESSOR_RO_INTR_REG(sz, MIPS_GIC_REDIR_OFS + off,		\
+				 stride, vo_##name)
+
+/* For read-write local per-interrupt registers */
+#define GIC_VX_ACCESSOR_RW_INTR_REG(sz, off, stride, name)		\
+	GIC_ACCESSOR_RW_INTR_REG(sz, MIPS_GIC_LOCAL_OFS + off,		\
+				 stride, vl_##name)			\
+	GIC_ACCESSOR_RW_INTR_REG(sz, MIPS_GIC_REDIR_OFS + off,		\
+				 stride, vo_##name)
+
+/* For read-only shared bit-per-interrupt registers */
+#define GIC_ACCESSOR_RO_INTR_BIT(off, name)				\
+static inline void __iomem *addr_gic_##name(void)			\
+{									\
+	return mips_gic_base + (off);					\
+}									\
+									\
+static inline unsigned int read_gic_##name(unsigned int intr)		\
+{									\
+	void __iomem *addr = addr_gic_##name();				\
+	unsigned int val;						\
+									\
+	if (mips_cm_is64) {						\
+		addr += (intr / 64) * sizeof(uint64_t);			\
+		val = __raw_readq(addr) >> intr % 64;			\
+	} else {							\
+		addr += (intr / 32) * sizeof(uint32_t);			\
+		val = __raw_readl(addr) >> intr % 32;			\
+	}								\
+									\
+	return val & 0x1;						\
+}
+
+/* For read-write shared bit-per-interrupt registers */
+#define GIC_ACCESSOR_RW_INTR_BIT(off, name)				\
+	GIC_ACCESSOR_RO_INTR_BIT(off, name)				\
+									\
+static inline void write_gic_##name(unsigned int intr)			\
+{									\
+	void __iomem *addr = addr_gic_##name();				\
+									\
+	if (mips_cm_is64) {						\
+		addr += (intr / 64) * sizeof(uint64_t);			\
+		__raw_writeq(BIT(intr % 64), addr);			\
+	} else {							\
+		addr += (intr / 32) * sizeof(uint32_t);			\
+		__raw_writel(BIT(intr % 32), addr);			\
+	}								\
+}									\
+									\
+static inline void change_gic_##name(unsigned int intr,			\
+				     unsigned int val)			\
+{									\
+	void __iomem *addr = addr_gic_##name();				\
+									\
+	if (mips_cm_is64) {						\
+		uint64_t _val;						\
+									\
+		addr += (intr / 64) * sizeof(uint64_t);			\
+		_val = __raw_readq(addr);				\
+		_val &= ~BIT_ULL(intr % 64);				\
+		_val |= (uint64_t)val << (intr % 64);			\
+		__raw_writeq(_val, addr);				\
+	} else {							\
+		uint32_t _val;						\
+									\
+		addr += (intr / 32) * sizeof(uint32_t);			\
+		_val = __raw_readl(addr);				\
+		_val &= ~BIT(intr % 32);				\
+		_val |= val << (intr % 32);				\
+		__raw_writel(_val, addr);				\
+	}								\
+}
+
+/* For read-only local bit-per-interrupt registers */
+#define GIC_VX_ACCESSOR_RO_INTR_BIT(sz, off, name)			\
+	GIC_ACCESSOR_RO_INTR_BIT(sz, MIPS_GIC_LOCAL_OFS + off,		\
+				 vl_##name)				\
+	GIC_ACCESSOR_RO_INTR_BIT(sz, MIPS_GIC_REDIR_OFS + off,		\
+				 vo_##name)
+
+/* For read-write local bit-per-interrupt registers */
+#define GIC_VX_ACCESSOR_RW_INTR_BIT(sz, off, name)			\
+	GIC_ACCESSOR_RW_INTR_BIT(sz, MIPS_GIC_LOCAL_OFS + off,		\
+				 vl_##name)				\
+	GIC_ACCESSOR_RW_INTR_BIT(sz, MIPS_GIC_REDIR_OFS + off,		\
+				 vo_##name)
+
+/* GIC_SH_CONFIG - Information about the GIC configuration */
+GIC_ACCESSOR_RW(32, 0x000, config)
+#define GIC_CONFIG_COUNTSTOP		BIT(28)
+#define GIC_CONFIG_COUNTBITS		GENMASK(27, 24)
+#define GIC_CONFIG_NUMINTERRUPTS	GENMASK(23, 16)
+#define GIC_CONFIG_PVPS			GENMASK(6, 0)
+
+/* GIC_SH_COUNTER - Shared global counter value */
+GIC_ACCESSOR_RW(64, 0x010, counter)
+GIC_ACCESSOR_RW(32, 0x010, counter_32l)
+GIC_ACCESSOR_RW(32, 0x014, counter_32h)
+
+/* GIC_SH_POL_* - Configures interrupt polarity */
+GIC_ACCESSOR_RW_INTR_BIT(0x100, pol)
+#define GIC_POL_ACTIVE_LOW		0	/* when level triggered */
+#define GIC_POL_ACTIVE_HIGH		1	/* when level triggered */
+#define GIC_POL_FALLING_EDGE		0	/* when single-edge triggered */
+#define GIC_POL_RISING_EDGE		1	/* when single-edge triggered */
+
+/* GIC_SH_TRIG_* - Configures interrupts to be edge or level triggered */
+GIC_ACCESSOR_RW_INTR_BIT(0x180, trig)
+#define GIC_TRIG_LEVEL			0
+#define GIC_TRIG_EDGE			1
+
+/* GIC_SH_DUAL_* - Configures whether interrupts trigger on both edges */
+GIC_ACCESSOR_RW_INTR_BIT(0x200, dual)
+#define GIC_DUAL_SINGLE			0	/* when edge-triggered */
+#define GIC_DUAL_DUAL			1	/* when edge-triggered */
+
+/* GIC_SH_WEDGE - Write an 'edge', ie. trigger an interrupt */
+GIC_ACCESSOR_RW(32, 0x280, wedge)
+#define GIC_WEDGE_RW			BIT(31)
+#define GIC_WEDGE_INTR			GENMASK(7, 0)
+
+/* GIC_SH_RMASK_* - Reset/clear shared interrupt mask bits */
+GIC_ACCESSOR_RW_INTR_BIT(0x300, rmask)
+
+/* GIC_SH_SMASK_* - Set shared interrupt mask bits */
+GIC_ACCESSOR_RW_INTR_BIT(0x380, smask)
+
+/* GIC_SH_MASK_* - Read the current shared interrupt mask */
+GIC_ACCESSOR_RO_INTR_BIT(0x400, mask)
+
+/* GIC_SH_PEND_* - Read currently pending shared interrupts */
+GIC_ACCESSOR_RO_INTR_BIT(0x480, pend)
+
+/* GIC_SH_MAPx_PIN - Map shared interrupts to a particular CPU pin */
+GIC_ACCESSOR_RW_INTR_REG(32, 0x500, 0x4, map_pin)
+#define GIC_MAP_PIN_MAP_TO_PIN		BIT(31)
+#define GIC_MAP_PIN_MAP_TO_NMI		BIT(30)
+#define GIC_MAP_PIN_MAP			GENMASK(5, 0)
+
+/* GIC_SH_MAPx_VP - Map shared interrupts to a particular Virtual Processor */
+GIC_ACCESSOR_RW_INTR_REG(32, 0x2000, 0x20, map_vp)
+
+/* GIC_Vx_CTL - VP-level interrupt control */
+GIC_VX_ACCESSOR_RW(32, 0x000, ctl)
+#define GIC_VX_CTL_FDC_ROUTABLE		BIT(4)
+#define GIC_VX_CTL_SWINT_ROUTABLE	BIT(3)
+#define GIC_VX_CTL_PERFCNT_ROUTABLE	BIT(2)
+#define GIC_VX_CTL_TIMER_ROUTABLE	BIT(1)
+#define GIC_VX_CTL_EIC			BIT(0)
+
+/* GIC_Vx_PEND - Read currently pending local interrupts */
+GIC_VX_ACCESSOR_RO(32, 0x004, pend)
+
+/* GIC_Vx_MASK - Read the current local interrupt mask */
+GIC_VX_ACCESSOR_RO(32, 0x008, mask)
+
+/* GIC_Vx_RMASK - Reset/clear local interrupt mask bits */
+GIC_VX_ACCESSOR_RW(32, 0x00c, rmask)
+
+/* GIC_Vx_SMASK - Set local interrupt mask bits */
+GIC_VX_ACCESSOR_RW(32, 0x010, smask)
+
+/* GIC_Vx_*_MAP - Route local interrupts to the desired pins */
+GIC_VX_ACCESSOR_RW_INTR_REG(32, 0x040, 0x4, map)
+
+/* GIC_Vx_WD_MAP - Route the local watchdog timer interrupt */
+GIC_VX_ACCESSOR_RW(32, 0x040, wd_map)
+
+/* GIC_Vx_COMPARE_MAP - Route the local count/compare interrupt */
+GIC_VX_ACCESSOR_RW(32, 0x044, compare_map)
+
+/* GIC_Vx_TIMER_MAP - Route the local CPU timer (cp0 count/compare) interrupt */
+GIC_VX_ACCESSOR_RW(32, 0x048, timer_map)
+
+/* GIC_Vx_FDC_MAP - Route the local fast debug channel interrupt */
+GIC_VX_ACCESSOR_RW(32, 0x04c, fdc_map)
+
+/* GIC_Vx_PERFCTR_MAP - Route the local performance counter interrupt */
+GIC_VX_ACCESSOR_RW(32, 0x050, perfctr_map)
+
+/* GIC_Vx_SWINT0_MAP - Route the local software interrupt 0 */
+GIC_VX_ACCESSOR_RW(32, 0x054, swint0_map)
+
+/* GIC_Vx_SWINT1_MAP - Route the local software interrupt 1 */
+GIC_VX_ACCESSOR_RW(32, 0x058, swint1_map)
+
+/* GIC_Vx_OTHER - Configure access to other Virtual Processor registers */
+GIC_VX_ACCESSOR_RW(32, 0x080, other)
+#define GIC_VX_OTHER_VPNUM		GENMASK(5, 0)
+
+/* GIC_Vx_IDENT - Retrieve the local Virtual Processor's ID */
+GIC_VX_ACCESSOR_RO(32, 0x088, ident)
+#define GIC_VX_IDENT_VPNUM		GENMASK(5, 0)
+
+/* GIC_Vx_COMPARE - Value to compare with GIC_SH_COUNTER */
+GIC_VX_ACCESSOR_RW(64, 0x0a0, compare)
+
+/* GIC_Vx_EIC_SHADOW_SET_BASE - Set shadow register set for each interrupt */
+GIC_VX_ACCESSOR_RW_INTR_REG(32, 0x100, 0x4, eic_shadow_set)
+
+/**
+ * enum mips_gic_local_interrupt - GIC local interrupts
+ * @GIC_LOCAL_INT_WD: GIC watchdog timer interrupt
+ * @GIC_LOCAL_INT_COMPARE: GIC count/compare interrupt
+ * @GIC_LOCAL_INT_TIMER: CP0 count/compare interrupt
+ * @GIC_LOCAL_INT_PERFCTR: Performance counter interrupt
+ * @GIC_LOCAL_INT_SWINT0: Software interrupt 0
+ * @GIC_LOCAL_INT_SWINT1: Software interrupt 1
+ * @GIC_LOCAL_INT_FDC: Fast debug channel interrupt
+ * @GIC_NUM_LOCAL_INTRS: The number of local interrupts
+ *
+ * Enumerates interrupts provided by the GIC that are local to a VP.
+ */
+enum mips_gic_local_interrupt {
+	GIC_LOCAL_INT_WD,
+	GIC_LOCAL_INT_COMPARE,
+	GIC_LOCAL_INT_TIMER,
+	GIC_LOCAL_INT_PERFCTR,
+	GIC_LOCAL_INT_SWINT0,
+	GIC_LOCAL_INT_SWINT1,
+	GIC_LOCAL_INT_FDC,
+	GIC_NUM_LOCAL_INTRS
+};
+
+/**
+ * mips_gic_present() - Determine whether a GIC is present
+ *
+ * Determines whether a MIPS Global Interrupt Controller (GIC) is present in
+ * the system that the kernel is running on.
+ *
+ * Return true if a GIC is present, else false.
+ */
+static inline bool mips_gic_present(void)
+{
+	return IS_ENABLED(CONFIG_MIPS_GIC) && mips_gic_base;
+}
+
+/**
+ * mips_gic_vx_map_reg() - Return GIC_Vx_<intr>_MAP register offset
+ * @intr: A GIC local interrupt
+ *
+ * Determine the index of the GIC_VL_<intr>_MAP or GIC_VO_<intr>_MAP register
+ * within the block of GIC map registers. This is almost the same as the order
+ * of interrupts in the pending & mask registers, as used by enum
+ * mips_gic_local_interrupt, but moves the FDC interrupt & thus offsets the
+ * interrupts after it...
+ *
+ * Return: The map register index corresponding to @intr.
+ *
+ * The return value is suitable for use with the (read|write)_gic_v[lo]_map
+ * accessor functions.
+ */
+static inline unsigned int
+mips_gic_vx_map_reg(enum mips_gic_local_interrupt intr)
+{
+	/* WD, Compare & Timer are 1:1 */
+	if (intr <= GIC_LOCAL_INT_TIMER)
+		return intr;
+
+	/* FDC moves to after Timer... */
+	if (intr == GIC_LOCAL_INT_FDC)
+		return GIC_LOCAL_INT_TIMER + 1;
+
+	/* As a result everything else is offset by 1 */
+	return intr + 1;
+}
+
+/**
+ * gic_get_c0_compare_int() - Return cp0 count/compare interrupt virq
+ *
+ * Determine the virq number to use for the coprocessor 0 count/compare
+ * interrupt, which may be routed via the GIC.
+ *
+ * Returns the virq number or a negative error number.
+ */
+extern int gic_get_c0_compare_int(void);
+
+/**
+ * gic_get_c0_perfcount_int() - Return performance counter interrupt virq
+ *
+ * Determine the virq number to use for CPU performance counter interrupts,
+ * which may be routed via the GIC.
+ *
+ * Returns the virq number or a negative error number.
+ */
+extern int gic_get_c0_perfcount_int(void);
+
+/**
+ * gic_get_c0_fdc_int() - Return fast debug channel interrupt virq
+ *
+ * Determine the virq number to use for fast debug channel (FDC) interrupts,
+ * which may be routed via the GIC.
+ *
+ * Returns the virq number or a negative error number.
+ */
+extern int gic_get_c0_fdc_int(void);
+
+#endif /* __MIPS_ASM_MIPS_CPS_H__ */
diff --git a/arch/mips/include/asm/mips-r2-to-r6-emul.h b/arch/mips/include/asm/mips-r2-to-r6-emul.h
new file mode 100644
index 000000000..20621e1ca
--- /dev/null
+++ b/arch/mips/include/asm/mips-r2-to-r6-emul.h
@@ -0,0 +1,101 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (c) 2014 Imagination Technologies Ltd.
+ * Author: Markos Chandras <markos.chandras@imgtec.com>
+ */
+
+#ifndef __ASM_MIPS_R2_TO_R6_EMUL_H
+#define __ASM_MIPS_R2_TO_R6_EMUL_H
+
+struct mips_r2_emulator_stats {
+	u64 movs;
+	u64 hilo;
+	u64 muls;
+	u64 divs;
+	u64 dsps;
+	u64 bops;
+	u64 traps;
+	u64 fpus;
+	u64 loads;
+	u64 stores;
+	u64 llsc;
+	u64 dsemul;
+};
+
+struct mips_r2br_emulator_stats {
+	u64 jrs;
+	u64 bltzl;
+	u64 bgezl;
+	u64 bltzll;
+	u64 bgezll;
+	u64 bltzall;
+	u64 bgezall;
+	u64 bltzal;
+	u64 bgezal;
+	u64 beql;
+	u64 bnel;
+	u64 blezl;
+	u64 bgtzl;
+};
+
+#ifdef CONFIG_DEBUG_FS
+
+#define MIPS_R2_STATS(M)						\
+do {									\
+	u32 nir;							\
+	int err;							\
+									\
+	preempt_disable();						\
+	__this_cpu_inc(mipsr2emustats.M);				\
+	err = __get_user(nir, (u32 __user *)regs->cp0_epc);		\
+	if (!err) {							\
+		if (nir == BREAK_MATH(0))				\
+			__this_cpu_inc(mipsr2bdemustats.M);		\
+	}								\
+	preempt_enable();						\
+} while (0)
+
+#define MIPS_R2BR_STATS(M)					\
+do {								\
+	preempt_disable();					\
+	__this_cpu_inc(mipsr2bremustats.M);			\
+	preempt_enable();					\
+} while (0)
+
+#else
+
+#define MIPS_R2_STATS(M)          do { } while (0)
+#define MIPS_R2BR_STATS(M)        do { } while (0)
+
+#endif /* CONFIG_DEBUG_FS */
+
+struct r2_decoder_table {
+	u32     mask;
+	u32     code;
+	int     (*func)(struct pt_regs *regs, u32 inst);
+};
+
+
+extern void do_trap_or_bp(struct pt_regs *regs, unsigned int code, int si_code,
+			  const char *str);
+
+#ifndef CONFIG_MIPSR2_TO_R6_EMULATOR
+static int mipsr2_emulation;
+static inline int mipsr2_decoder(struct pt_regs *regs, u32 inst,
+				 unsigned long *fcr31)
+{
+	return 0;
+};
+#else
+/* MIPS R2 Emulator ON/OFF */
+extern int mipsr2_emulation;
+extern int mipsr2_decoder(struct pt_regs *regs, u32 inst,
+			  unsigned long *fcr31);
+#endif /* CONFIG_MIPSR2_TO_R6_EMULATOR */
+
+#define NO_R6EMU	(cpu_has_mips_r6 && !mipsr2_emulation)
+
+#endif /* __ASM_MIPS_R2_TO_R6_EMUL_H */
diff --git a/arch/mips/include/asm/mips_mt.h b/arch/mips/include/asm/mips_mt.h
new file mode 100644
index 000000000..b444523ec
--- /dev/null
+++ b/arch/mips/include/asm/mips_mt.h
@@ -0,0 +1,31 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Definitions and declarations for MIPS MT support that are common between
+ * the VSMP, and AP/SP kernel models.
+ */
+#ifndef __ASM_MIPS_MT_H
+#define __ASM_MIPS_MT_H
+
+#include <linux/cpumask.h>
+
+/*
+ * How many VPEs and TCs is Linux allowed to use?  0 means no limit.
+ */
+extern int tclimit;
+extern int vpelimit;
+
+extern cpumask_t mt_fpu_cpumask;
+extern unsigned long mt_fpemul_threshold;
+
+extern void mips_mt_regdump(unsigned long previous_mvpcontrol_value);
+
+#ifdef CONFIG_MIPS_MT
+extern void mips_mt_set_cpuoptions(void);
+#else
+static inline void mips_mt_set_cpuoptions(void) { }
+#endif
+
+struct class;
+extern struct class *mt_class;
+
+#endif /* __ASM_MIPS_MT_H */
diff --git a/arch/mips/include/asm/mipsmtregs.h b/arch/mips/include/asm/mipsmtregs.h
new file mode 100644
index 000000000..a8d67c2f4
--- /dev/null
+++ b/arch/mips/include/asm/mipsmtregs.h
@@ -0,0 +1,422 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * MT regs definitions, follows on from mipsregs.h
+ * Copyright (C) 2004 - 2005 MIPS Technologies, Inc.  All rights reserved.
+ * Elizabeth Clarke et. al.
+ *
+ */
+#ifndef _ASM_MIPSMTREGS_H
+#define _ASM_MIPSMTREGS_H
+
+#include <asm/mipsregs.h>
+
+#ifndef __ASSEMBLY__
+
+/*
+ * C macros
+ */
+
+#define read_c0_mvpcontrol()		__read_32bit_c0_register($0, 1)
+#define write_c0_mvpcontrol(val)	__write_32bit_c0_register($0, 1, val)
+
+#define read_c0_mvpconf0()		__read_32bit_c0_register($0, 2)
+#define read_c0_mvpconf1()		__read_32bit_c0_register($0, 3)
+
+#define read_c0_vpecontrol()		__read_32bit_c0_register($1, 1)
+#define write_c0_vpecontrol(val)	__write_32bit_c0_register($1, 1, val)
+
+#define read_c0_vpeconf0()		__read_32bit_c0_register($1, 2)
+#define write_c0_vpeconf0(val)		__write_32bit_c0_register($1, 2, val)
+
+#define read_c0_vpeconf1()		__read_32bit_c0_register($1, 3)
+#define write_c0_vpeconf1(val)		__write_32bit_c0_register($1, 3, val)
+
+#define read_c0_tcstatus()		__read_32bit_c0_register($2, 1)
+#define write_c0_tcstatus(val)		__write_32bit_c0_register($2, 1, val)
+
+#define read_c0_tcbind()		__read_32bit_c0_register($2, 2)
+
+#define write_c0_tchalt(val)		__write_32bit_c0_register($2, 4, val)
+
+#define read_c0_tccontext()		__read_32bit_c0_register($2, 5)
+#define write_c0_tccontext(val)		__write_32bit_c0_register($2, 5, val)
+
+#else /* Assembly */
+/*
+ * Macros for use in assembly language code
+ */
+
+#define CP0_MVPCONTROL		$0, 1
+#define CP0_MVPCONF0		$0, 2
+#define CP0_MVPCONF1		$0, 3
+#define CP0_VPECONTROL		$1, 1
+#define CP0_VPECONF0		$1, 2
+#define CP0_VPECONF1		$1, 3
+#define CP0_YQMASK		$1, 4
+#define CP0_VPESCHEDULE		$1, 5
+#define CP0_VPESCHEFBK		$1, 6
+#define CP0_TCSTATUS		$2, 1
+#define CP0_TCBIND		$2, 2
+#define CP0_TCRESTART		$2, 3
+#define CP0_TCHALT		$2, 4
+#define CP0_TCCONTEXT		$2, 5
+#define CP0_TCSCHEDULE		$2, 6
+#define CP0_TCSCHEFBK		$2, 7
+#define CP0_SRSCONF0		$6, 1
+#define CP0_SRSCONF1		$6, 2
+#define CP0_SRSCONF2		$6, 3
+#define CP0_SRSCONF3		$6, 4
+#define CP0_SRSCONF4		$6, 5
+
+#endif
+
+/* MVPControl fields */
+#define MVPCONTROL_EVP		(_ULCAST_(1))
+
+#define MVPCONTROL_VPC_SHIFT	1
+#define MVPCONTROL_VPC		(_ULCAST_(1) << MVPCONTROL_VPC_SHIFT)
+
+#define MVPCONTROL_STLB_SHIFT	2
+#define MVPCONTROL_STLB		(_ULCAST_(1) << MVPCONTROL_STLB_SHIFT)
+
+
+/* MVPConf0 fields */
+#define MVPCONF0_PTC_SHIFT	0
+#define MVPCONF0_PTC		( _ULCAST_(0xff))
+#define MVPCONF0_PVPE_SHIFT	10
+#define MVPCONF0_PVPE		( _ULCAST_(0xf) << MVPCONF0_PVPE_SHIFT)
+#define MVPCONF0_TCA_SHIFT	15
+#define MVPCONF0_TCA		( _ULCAST_(1) << MVPCONF0_TCA_SHIFT)
+#define MVPCONF0_PTLBE_SHIFT	16
+#define MVPCONF0_PTLBE		(_ULCAST_(0x3ff) << MVPCONF0_PTLBE_SHIFT)
+#define MVPCONF0_TLBS_SHIFT	29
+#define MVPCONF0_TLBS		(_ULCAST_(1) << MVPCONF0_TLBS_SHIFT)
+#define MVPCONF0_M_SHIFT	31
+#define MVPCONF0_M		(_ULCAST_(0x1) << MVPCONF0_M_SHIFT)
+
+
+/* config3 fields */
+#define CONFIG3_MT_SHIFT	2
+#define CONFIG3_MT		(_ULCAST_(1) << CONFIG3_MT_SHIFT)
+
+
+/* VPEControl fields (per VPE) */
+#define VPECONTROL_TARGTC	(_ULCAST_(0xff))
+
+#define VPECONTROL_TE_SHIFT	15
+#define VPECONTROL_TE		(_ULCAST_(1) << VPECONTROL_TE_SHIFT)
+#define VPECONTROL_EXCPT_SHIFT	16
+#define VPECONTROL_EXCPT	(_ULCAST_(0x7) << VPECONTROL_EXCPT_SHIFT)
+
+/* Thread Exception Codes for EXCPT field */
+#define THREX_TU		0
+#define THREX_TO		1
+#define THREX_IYQ		2
+#define THREX_GSX		3
+#define THREX_YSCH		4
+#define THREX_GSSCH		5
+
+#define VPECONTROL_GSI_SHIFT	20
+#define VPECONTROL_GSI		(_ULCAST_(1) << VPECONTROL_GSI_SHIFT)
+#define VPECONTROL_YSI_SHIFT	21
+#define VPECONTROL_YSI		(_ULCAST_(1) << VPECONTROL_YSI_SHIFT)
+
+/* VPEConf0 fields (per VPE) */
+#define VPECONF0_VPA_SHIFT	0
+#define VPECONF0_VPA		(_ULCAST_(1) << VPECONF0_VPA_SHIFT)
+#define VPECONF0_MVP_SHIFT	1
+#define VPECONF0_MVP		(_ULCAST_(1) << VPECONF0_MVP_SHIFT)
+#define VPECONF0_XTC_SHIFT	21
+#define VPECONF0_XTC		(_ULCAST_(0xff) << VPECONF0_XTC_SHIFT)
+
+/* VPEConf1 fields (per VPE) */
+#define VPECONF1_NCP1_SHIFT	0
+#define VPECONF1_NCP1		(_ULCAST_(0xff) << VPECONF1_NCP1_SHIFT)
+#define VPECONF1_NCP2_SHIFT	10
+#define VPECONF1_NCP2		(_ULCAST_(0xff) << VPECONF1_NCP2_SHIFT)
+#define VPECONF1_NCX_SHIFT	20
+#define VPECONF1_NCX		(_ULCAST_(0xff) << VPECONF1_NCX_SHIFT)
+
+/* TCStatus fields (per TC) */
+#define TCSTATUS_TASID		(_ULCAST_(0xff))
+#define TCSTATUS_IXMT_SHIFT	10
+#define TCSTATUS_IXMT		(_ULCAST_(1) << TCSTATUS_IXMT_SHIFT)
+#define TCSTATUS_TKSU_SHIFT	11
+#define TCSTATUS_TKSU		(_ULCAST_(3) << TCSTATUS_TKSU_SHIFT)
+#define TCSTATUS_A_SHIFT	13
+#define TCSTATUS_A		(_ULCAST_(1) << TCSTATUS_A_SHIFT)
+#define TCSTATUS_DA_SHIFT	15
+#define TCSTATUS_DA		(_ULCAST_(1) << TCSTATUS_DA_SHIFT)
+#define TCSTATUS_DT_SHIFT	20
+#define TCSTATUS_DT		(_ULCAST_(1) << TCSTATUS_DT_SHIFT)
+#define TCSTATUS_TDS_SHIFT	21
+#define TCSTATUS_TDS		(_ULCAST_(1) << TCSTATUS_TDS_SHIFT)
+#define TCSTATUS_TSST_SHIFT	22
+#define TCSTATUS_TSST		(_ULCAST_(1) << TCSTATUS_TSST_SHIFT)
+#define TCSTATUS_RNST_SHIFT	23
+#define TCSTATUS_RNST		(_ULCAST_(3) << TCSTATUS_RNST_SHIFT)
+/* Codes for RNST */
+#define TC_RUNNING		0
+#define TC_WAITING		1
+#define TC_YIELDING		2
+#define TC_GATED		3
+
+#define TCSTATUS_TMX_SHIFT	27
+#define TCSTATUS_TMX		(_ULCAST_(1) << TCSTATUS_TMX_SHIFT)
+/* TCStatus TCU bits can use same definitions/offsets as CU bits in Status */
+
+/* TCBind */
+#define TCBIND_CURVPE_SHIFT	0
+#define TCBIND_CURVPE		(_ULCAST_(0xf))
+
+#define TCBIND_CURTC_SHIFT	21
+
+#define TCBIND_CURTC		(_ULCAST_(0xff) << TCBIND_CURTC_SHIFT)
+
+/* TCHalt */
+#define TCHALT_H		(_ULCAST_(1))
+
+#ifndef __ASSEMBLY__
+
+static inline unsigned core_nvpes(void)
+{
+	unsigned conf0;
+
+	if (!cpu_has_mipsmt)
+		return 1;
+
+	conf0 = read_c0_mvpconf0();
+	return ((conf0 & MVPCONF0_PVPE) >> MVPCONF0_PVPE_SHIFT) + 1;
+}
+
+static inline unsigned int dvpe(void)
+{
+	int res = 0;
+
+	__asm__ __volatile__(
+	"	.set	push						\n"
+	"	.set	noreorder					\n"
+	"	.set	noat						\n"
+	"	.set	mips32r2					\n"
+	"	.word	0x41610001		# dvpe $1		\n"
+	"	move	%0, $1						\n"
+	"	ehb							\n"
+	"	.set	pop						\n"
+	: "=r" (res));
+
+	instruction_hazard();
+
+	return res;
+}
+
+static inline void __raw_evpe(void)
+{
+	__asm__ __volatile__(
+	"	.set	push						\n"
+	"	.set	noreorder					\n"
+	"	.set	noat						\n"
+	"	.set	mips32r2					\n"
+	"	.word	0x41600021		# evpe			\n"
+	"	ehb							\n"
+	"	.set	pop						\n");
+}
+
+/* Enable virtual processor execution if previous suggested it should be.
+   EVPE_ENABLE to force */
+
+#define EVPE_ENABLE MVPCONTROL_EVP
+
+static inline void evpe(int previous)
+{
+	if ((previous & MVPCONTROL_EVP))
+		__raw_evpe();
+}
+
+static inline unsigned int dmt(void)
+{
+	int res;
+
+	__asm__ __volatile__(
+	"	.set	push						\n"
+	"	.set	mips32r2					\n"
+	"	.set	noat						\n"
+	"	.word	0x41610BC1			# dmt $1	\n"
+	"	ehb							\n"
+	"	move	%0, $1						\n"
+	"	.set	pop						\n"
+	: "=r" (res));
+
+	instruction_hazard();
+
+	return res;
+}
+
+static inline void __raw_emt(void)
+{
+	__asm__ __volatile__(
+	"	.set	push						\n"
+	"	.set	noreorder					\n"
+	"	.set	mips32r2					\n"
+	"	.word	0x41600be1			# emt		\n"
+	"	ehb							\n"
+	"	.set	pop");
+}
+
+/* enable multi-threaded execution if previous suggested it should be.
+   EMT_ENABLE to force */
+
+#define EMT_ENABLE VPECONTROL_TE
+
+static inline void emt(int previous)
+{
+	if ((previous & EMT_ENABLE))
+		__raw_emt();
+}
+
+static inline void ehb(void)
+{
+	__asm__ __volatile__(
+	"	.set	push					\n"
+	"	.set	mips32r2				\n"
+	"	ehb						\n"
+	"	.set	pop					\n");
+}
+
+#define mftc0(rt,sel)							\
+({									\
+	 unsigned long	__res;						\
+									\
+	__asm__ __volatile__(						\
+	"	.set	push					\n"	\
+	"	.set	mips32r2				\n"	\
+	"	.set	noat					\n"	\
+	"	# mftc0 $1, $" #rt ", " #sel "			\n"	\
+	"	.word	0x41000800 | (" #rt " << 16) | " #sel " \n"	\
+	"	move	%0, $1					\n"	\
+	"	.set	pop					\n"	\
+	: "=r" (__res));						\
+									\
+	__res;								\
+})
+
+#define mftgpr(rt)							\
+({									\
+	unsigned long __res;						\
+									\
+	__asm__ __volatile__(						\
+	"	.set	push					\n"	\
+	"	.set	noat					\n"	\
+	"	.set	mips32r2				\n"	\
+	"	# mftgpr $1," #rt "				\n"	\
+	"	.word	0x41000820 | (" #rt " << 16)		\n"	\
+	"	move	%0, $1					\n"	\
+	"	.set	pop					\n"	\
+	: "=r" (__res));						\
+									\
+	__res;								\
+})
+
+#define mftr(rt, u, sel)							\
+({									\
+	unsigned long __res;						\
+									\
+	__asm__ __volatile__(						\
+	"	mftr	%0, " #rt ", " #u ", " #sel "		\n"	\
+	: "=r" (__res));						\
+									\
+	__res;								\
+})
+
+#define mttgpr(rd,v)							\
+do {									\
+	__asm__ __volatile__(						\
+	"	.set	push					\n"	\
+	"	.set	mips32r2				\n"	\
+	"	.set	noat					\n"	\
+	"	move	$1, %0					\n"	\
+	"	# mttgpr $1, " #rd "				\n"	\
+	"	.word	0x41810020 | (" #rd " << 11)		\n"	\
+	"	.set	pop					\n"	\
+	: : "r" (v));							\
+} while (0)
+
+#define mttc0(rd, sel, v)							\
+({									\
+	__asm__ __volatile__(						\
+	"	.set	push					\n"	\
+	"	.set	mips32r2				\n"	\
+	"	.set	noat					\n"	\
+	"	move	$1, %0					\n"	\
+	"	# mttc0 %0," #rd ", " #sel "			\n"	\
+	"	.word	0x41810000 | (" #rd " << 11) | " #sel " \n"	\
+	"	.set	pop					\n"	\
+	:								\
+	: "r" (v));							\
+})
+
+
+#define mttr(rd, u, sel, v)						\
+({									\
+	__asm__ __volatile__(						\
+	"mttr	%0," #rd ", " #u ", " #sel				\
+	: : "r" (v));							\
+})
+
+
+#define settc(tc)							\
+do {									\
+	write_c0_vpecontrol((read_c0_vpecontrol()&~VPECONTROL_TARGTC) | (tc)); \
+	ehb();								\
+} while (0)
+
+
+/* you *must* set the target tc (settc) before trying to use these */
+#define read_vpe_c0_vpecontrol()	mftc0(1, 1)
+#define write_vpe_c0_vpecontrol(val)	mttc0(1, 1, val)
+#define read_vpe_c0_vpeconf0()		mftc0(1, 2)
+#define write_vpe_c0_vpeconf0(val)	mttc0(1, 2, val)
+#define read_vpe_c0_vpeconf1()		mftc0(1, 3)
+#define write_vpe_c0_vpeconf1(val)	mttc0(1, 3, val)
+#define read_vpe_c0_count()		mftc0(9, 0)
+#define write_vpe_c0_count(val)		mttc0(9, 0, val)
+#define read_vpe_c0_status()		mftc0(12, 0)
+#define write_vpe_c0_status(val)	mttc0(12, 0, val)
+#define read_vpe_c0_cause()		mftc0(13, 0)
+#define write_vpe_c0_cause(val)		mttc0(13, 0, val)
+#define read_vpe_c0_config()		mftc0(16, 0)
+#define write_vpe_c0_config(val)	mttc0(16, 0, val)
+#define read_vpe_c0_config1()		mftc0(16, 1)
+#define write_vpe_c0_config1(val)	mttc0(16, 1, val)
+#define read_vpe_c0_config7()		mftc0(16, 7)
+#define write_vpe_c0_config7(val)	mttc0(16, 7, val)
+#define read_vpe_c0_ebase()		mftc0(15, 1)
+#define write_vpe_c0_ebase(val)		mttc0(15, 1, val)
+#define write_vpe_c0_compare(val)	mttc0(11, 0, val)
+#define read_vpe_c0_badvaddr()		mftc0(8, 0)
+#define read_vpe_c0_epc()		mftc0(14, 0)
+#define write_vpe_c0_epc(val)		mttc0(14, 0, val)
+
+
+/* TC */
+#define read_tc_c0_tcstatus()		mftc0(2, 1)
+#define write_tc_c0_tcstatus(val)	mttc0(2, 1, val)
+#define read_tc_c0_tcbind()		mftc0(2, 2)
+#define write_tc_c0_tcbind(val)		mttc0(2, 2, val)
+#define read_tc_c0_tcrestart()		mftc0(2, 3)
+#define write_tc_c0_tcrestart(val)	mttc0(2, 3, val)
+#define read_tc_c0_tchalt()		mftc0(2, 4)
+#define write_tc_c0_tchalt(val)		mttc0(2, 4, val)
+#define read_tc_c0_tccontext()		mftc0(2, 5)
+#define write_tc_c0_tccontext(val)	mttc0(2, 5, val)
+
+/* GPR */
+#define read_tc_gpr_sp()		mftgpr(29)
+#define write_tc_gpr_sp(val)		mttgpr(29, val)
+#define read_tc_gpr_gp()		mftgpr(28)
+#define write_tc_gpr_gp(val)		mttgpr(28, val)
+
+__BUILD_SET_C0(mvpcontrol)
+
+#endif /* Not __ASSEMBLY__ */
+
+#endif
diff --git a/arch/mips/include/asm/mipsprom.h b/arch/mips/include/asm/mipsprom.h
new file mode 100644
index 000000000..2eda19f8f
--- /dev/null
+++ b/arch/mips/include/asm/mipsprom.h
@@ -0,0 +1,77 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_MIPSPROM_H
+#define __ASM_MIPSPROM_H
+
+#define PROM_RESET		0
+#define PROM_EXEC		1
+#define PROM_RESTART		2
+#define PROM_REINIT		3
+#define PROM_REBOOT		4
+#define PROM_AUTOBOOT		5
+#define PROM_OPEN		6
+#define PROM_READ		7
+#define PROM_WRITE		8
+#define PROM_IOCTL		9
+#define PROM_CLOSE		10
+#define PROM_GETCHAR		11
+#define PROM_PUTCHAR		12
+#define PROM_SHOWCHAR		13	/* XXX */
+#define PROM_GETS		14	/* XXX */
+#define PROM_PUTS		15	/* XXX */
+#define PROM_PRINTF		16	/* XXX */
+
+/* What are these for? */
+#define PROM_INITPROTO		17	/* XXX */
+#define PROM_PROTOENABLE	18	/* XXX */
+#define PROM_PROTODISABLE	19	/* XXX */
+#define PROM_GETPKT		20	/* XXX */
+#define PROM_PUTPKT		21	/* XXX */
+
+/* More PROM shit.  Probably has to do with VME RMW cycles??? */
+#define PROM_ORW_RMW		22	/* XXX */
+#define PROM_ORH_RMW		23	/* XXX */
+#define PROM_ORB_RMW		24	/* XXX */
+#define PROM_ANDW_RMW		25	/* XXX */
+#define PROM_ANDH_RMW		26	/* XXX */
+#define PROM_ANDB_RMW		27	/* XXX */
+
+/* Cache handling stuff */
+#define PROM_FLUSHCACHE		28	/* XXX */
+#define PROM_CLEARCACHE		29	/* XXX */
+
+/* Libc alike stuff */
+#define PROM_SETJMP		30	/* XXX */
+#define PROM_LONGJMP		31	/* XXX */
+#define PROM_BEVUTLB		32	/* XXX */
+#define PROM_GETENV		33	/* XXX */
+#define PROM_SETENV		34	/* XXX */
+#define PROM_ATOB		35	/* XXX */
+#define PROM_STRCMP		36	/* XXX */
+#define PROM_STRLEN		37	/* XXX */
+#define PROM_STRCPY		38	/* XXX */
+#define PROM_STRCAT		39	/* XXX */
+
+/* Misc stuff */
+#define PROM_PARSER		40	/* XXX */
+#define PROM_RANGE		41	/* XXX */
+#define PROM_ARGVIZE		42	/* XXX */
+#define PROM_HELP		43	/* XXX */
+
+/* Entry points for some PROM commands */
+#define PROM_DUMPCMD		44	/* XXX */
+#define PROM_SETENVCMD		45	/* XXX */
+#define PROM_UNSETENVCMD	46	/* XXX */
+#define PROM_PRINTENVCMD	47	/* XXX */
+#define PROM_BEVEXCEPT		48	/* XXX */
+#define PROM_ENABLECMD		49	/* XXX */
+#define PROM_DISABLECMD		50	/* XXX */
+
+#define PROM_CLEARNOFAULT	51	/* XXX */
+#define PROM_NOTIMPLEMENT	52	/* XXX */
+
+#define PROM_NV_GET		53	/* XXX */
+#define PROM_NV_SET		54	/* XXX */
+
+extern char *prom_getenv(char *);
+
+#endif /* __ASM_MIPSPROM_H */
diff --git a/arch/mips/include/asm/mipsregs.h b/arch/mips/include/asm/mipsregs.h
new file mode 100644
index 000000000..99eeafe6d
--- /dev/null
+++ b/arch/mips/include/asm/mipsregs.h
@@ -0,0 +1,2952 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994, 1995, 1996, 1997, 2000, 2001 by Ralf Baechle
+ * Copyright (C) 2000 Silicon Graphics, Inc.
+ * Modified for further R[236]000 support by Paul M. Antoine, 1996.
+ * Kevin D. Kissell, kevink@mips.com and Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 2000, 07 MIPS Technologies, Inc.
+ * Copyright (C) 2003, 2004  Maciej W. Rozycki
+ */
+#ifndef _ASM_MIPSREGS_H
+#define _ASM_MIPSREGS_H
+
+#include <linux/linkage.h>
+#include <linux/types.h>
+#include <asm/hazards.h>
+#include <asm/isa-rev.h>
+
+/*
+ * The following macros are especially useful for __asm__
+ * inline assembler.
+ */
+#ifndef __STR
+#define __STR(x) #x
+#endif
+#ifndef STR
+#define STR(x) __STR(x)
+#endif
+
+/*
+ *  Configure language
+ */
+#ifdef __ASSEMBLY__
+#define _ULCAST_
+#define _U64CAST_
+#else
+#define _ULCAST_ (unsigned long)
+#define _U64CAST_ (u64)
+#endif
+
+/*
+ * Coprocessor 0 register names
+ */
+#define CP0_INDEX $0
+#define CP0_RANDOM $1
+#define CP0_ENTRYLO0 $2
+#define CP0_ENTRYLO1 $3
+#define CP0_CONF $3
+#define CP0_GLOBALNUMBER $3, 1
+#define CP0_CONTEXT $4
+#define CP0_PAGEMASK $5
+#define CP0_PAGEGRAIN $5, 1
+#define CP0_SEGCTL0 $5, 2
+#define CP0_SEGCTL1 $5, 3
+#define CP0_SEGCTL2 $5, 4
+#define CP0_WIRED $6
+#define CP0_INFO $7
+#define CP0_HWRENA $7
+#define CP0_BADVADDR $8
+#define CP0_BADINSTR $8, 1
+#define CP0_COUNT $9
+#define CP0_ENTRYHI $10
+#define CP0_GUESTCTL1 $10, 4
+#define CP0_GUESTCTL2 $10, 5
+#define CP0_GUESTCTL3 $10, 6
+#define CP0_COMPARE $11
+#define CP0_GUESTCTL0EXT $11, 4
+#define CP0_STATUS $12
+#define CP0_GUESTCTL0 $12, 6
+#define CP0_GTOFFSET $12, 7
+#define CP0_CAUSE $13
+#define CP0_EPC $14
+#define CP0_PRID $15
+#define CP0_EBASE $15, 1
+#define CP0_CMGCRBASE $15, 3
+#define CP0_CONFIG $16
+#define CP0_CONFIG3 $16, 3
+#define CP0_CONFIG5 $16, 5
+#define CP0_CONFIG6 $16, 6
+#define CP0_LLADDR $17
+#define CP0_WATCHLO $18
+#define CP0_WATCHHI $19
+#define CP0_XCONTEXT $20
+#define CP0_FRAMEMASK $21
+#define CP0_DIAGNOSTIC $22
+#define CP0_DIAGNOSTIC1 $22, 1
+#define CP0_DEBUG $23
+#define CP0_DEPC $24
+#define CP0_PERFORMANCE $25
+#define CP0_ECC $26
+#define CP0_CACHEERR $27
+#define CP0_TAGLO $28
+#define CP0_TAGHI $29
+#define CP0_ERROREPC $30
+#define CP0_DESAVE $31
+
+/*
+ * R4640/R4650 cp0 register names.  These registers are listed
+ * here only for completeness; without MMU these CPUs are not useable
+ * by Linux.  A future ELKS port might take make Linux run on them
+ * though ...
+ */
+#define CP0_IBASE $0
+#define CP0_IBOUND $1
+#define CP0_DBASE $2
+#define CP0_DBOUND $3
+#define CP0_CALG $17
+#define CP0_IWATCH $18
+#define CP0_DWATCH $19
+
+/*
+ * Coprocessor 0 Set 1 register names
+ */
+#define CP0_S1_DERRADDR0  $26
+#define CP0_S1_DERRADDR1  $27
+#define CP0_S1_INTCONTROL $20
+
+/*
+ * Coprocessor 0 Set 2 register names
+ */
+#define CP0_S2_SRSCTL	  $12	/* MIPSR2 */
+
+/*
+ * Coprocessor 0 Set 3 register names
+ */
+#define CP0_S3_SRSMAP	  $12	/* MIPSR2 */
+
+/*
+ *  TX39 Series
+ */
+#define CP0_TX39_CACHE	$7
+
+
+/* Generic EntryLo bit definitions */
+#define ENTRYLO_G		(_ULCAST_(1) << 0)
+#define ENTRYLO_V		(_ULCAST_(1) << 1)
+#define ENTRYLO_D		(_ULCAST_(1) << 2)
+#define ENTRYLO_C_SHIFT		3
+#define ENTRYLO_C		(_ULCAST_(7) << ENTRYLO_C_SHIFT)
+
+/* R3000 EntryLo bit definitions */
+#define R3K_ENTRYLO_G		(_ULCAST_(1) << 8)
+#define R3K_ENTRYLO_V		(_ULCAST_(1) << 9)
+#define R3K_ENTRYLO_D		(_ULCAST_(1) << 10)
+#define R3K_ENTRYLO_N		(_ULCAST_(1) << 11)
+
+/* MIPS32/64 EntryLo bit definitions */
+#define MIPS_ENTRYLO_PFN_SHIFT	6
+#define MIPS_ENTRYLO_XI		(_ULCAST_(1) << (BITS_PER_LONG - 2))
+#define MIPS_ENTRYLO_RI		(_ULCAST_(1) << (BITS_PER_LONG - 1))
+
+/*
+ * MIPSr6+ GlobalNumber register definitions
+ */
+#define MIPS_GLOBALNUMBER_VP_SHF	0
+#define MIPS_GLOBALNUMBER_VP		(_ULCAST_(0xff) << MIPS_GLOBALNUMBER_VP_SHF)
+#define MIPS_GLOBALNUMBER_CORE_SHF	8
+#define MIPS_GLOBALNUMBER_CORE		(_ULCAST_(0xff) << MIPS_GLOBALNUMBER_CORE_SHF)
+#define MIPS_GLOBALNUMBER_CLUSTER_SHF	16
+#define MIPS_GLOBALNUMBER_CLUSTER	(_ULCAST_(0xf) << MIPS_GLOBALNUMBER_CLUSTER_SHF)
+
+/*
+ * Values for PageMask register
+ */
+#define PM_4K		0x00000000
+#define PM_8K		0x00002000
+#define PM_16K		0x00006000
+#define PM_32K		0x0000e000
+#define PM_64K		0x0001e000
+#define PM_128K		0x0003e000
+#define PM_256K		0x0007e000
+#define PM_512K		0x000fe000
+#define PM_1M		0x001fe000
+#define PM_2M		0x003fe000
+#define PM_4M		0x007fe000
+#define PM_8M		0x00ffe000
+#define PM_16M		0x01ffe000
+#define PM_32M		0x03ffe000
+#define PM_64M		0x07ffe000
+#define PM_256M		0x1fffe000
+#define PM_1G		0x7fffe000
+
+/*
+ * Default page size for a given kernel configuration
+ */
+#ifdef CONFIG_PAGE_SIZE_4KB
+#define PM_DEFAULT_MASK PM_4K
+#elif defined(CONFIG_PAGE_SIZE_8KB)
+#define PM_DEFAULT_MASK PM_8K
+#elif defined(CONFIG_PAGE_SIZE_16KB)
+#define PM_DEFAULT_MASK PM_16K
+#elif defined(CONFIG_PAGE_SIZE_32KB)
+#define PM_DEFAULT_MASK PM_32K
+#elif defined(CONFIG_PAGE_SIZE_64KB)
+#define PM_DEFAULT_MASK PM_64K
+#else
+#error Bad page size configuration!
+#endif
+
+/*
+ * Default huge tlb size for a given kernel configuration
+ */
+#ifdef CONFIG_PAGE_SIZE_4KB
+#define PM_HUGE_MASK	PM_1M
+#elif defined(CONFIG_PAGE_SIZE_8KB)
+#define PM_HUGE_MASK	PM_4M
+#elif defined(CONFIG_PAGE_SIZE_16KB)
+#define PM_HUGE_MASK	PM_16M
+#elif defined(CONFIG_PAGE_SIZE_32KB)
+#define PM_HUGE_MASK	PM_64M
+#elif defined(CONFIG_PAGE_SIZE_64KB)
+#define PM_HUGE_MASK	PM_256M
+#elif defined(CONFIG_MIPS_HUGE_TLB_SUPPORT)
+#error Bad page size configuration for hugetlbfs!
+#endif
+
+/*
+ * Wired register bits
+ */
+#define MIPSR6_WIRED_LIMIT_SHIFT 16
+#define MIPSR6_WIRED_LIMIT	(_ULCAST_(0xffff) << MIPSR6_WIRED_LIMIT_SHIFT)
+#define MIPSR6_WIRED_WIRED_SHIFT 0
+#define MIPSR6_WIRED_WIRED	(_ULCAST_(0xffff) << MIPSR6_WIRED_WIRED_SHIFT)
+
+/*
+ * Values used for computation of new tlb entries
+ */
+#define PL_4K		12
+#define PL_16K		14
+#define PL_64K		16
+#define PL_256K		18
+#define PL_1M		20
+#define PL_4M		22
+#define PL_16M		24
+#define PL_64M		26
+#define PL_256M		28
+
+/*
+ * PageGrain bits
+ */
+#define PG_RIE		(_ULCAST_(1) <<	 31)
+#define PG_XIE		(_ULCAST_(1) <<	 30)
+#define PG_ELPA		(_ULCAST_(1) <<	 29)
+#define PG_ESP		(_ULCAST_(1) <<	 28)
+#define PG_IEC		(_ULCAST_(1) <<  27)
+
+/* MIPS32/64 EntryHI bit definitions */
+#define MIPS_ENTRYHI_EHINV	(_ULCAST_(1) << 10)
+#define MIPS_ENTRYHI_ASIDX	(_ULCAST_(0x3) << 8)
+#define MIPS_ENTRYHI_ASID	(_ULCAST_(0xff) << 0)
+
+/*
+ * R4x00 interrupt enable / cause bits
+ */
+#define IE_SW0		(_ULCAST_(1) <<	 8)
+#define IE_SW1		(_ULCAST_(1) <<	 9)
+#define IE_IRQ0		(_ULCAST_(1) << 10)
+#define IE_IRQ1		(_ULCAST_(1) << 11)
+#define IE_IRQ2		(_ULCAST_(1) << 12)
+#define IE_IRQ3		(_ULCAST_(1) << 13)
+#define IE_IRQ4		(_ULCAST_(1) << 14)
+#define IE_IRQ5		(_ULCAST_(1) << 15)
+
+/*
+ * R4x00 interrupt cause bits
+ */
+#define C_SW0		(_ULCAST_(1) <<	 8)
+#define C_SW1		(_ULCAST_(1) <<	 9)
+#define C_IRQ0		(_ULCAST_(1) << 10)
+#define C_IRQ1		(_ULCAST_(1) << 11)
+#define C_IRQ2		(_ULCAST_(1) << 12)
+#define C_IRQ3		(_ULCAST_(1) << 13)
+#define C_IRQ4		(_ULCAST_(1) << 14)
+#define C_IRQ5		(_ULCAST_(1) << 15)
+
+/*
+ * Bitfields in the R4xx0 cp0 status register
+ */
+#define ST0_IE			0x00000001
+#define ST0_EXL			0x00000002
+#define ST0_ERL			0x00000004
+#define ST0_KSU			0x00000018
+#  define KSU_USER		0x00000010
+#  define KSU_SUPERVISOR	0x00000008
+#  define KSU_KERNEL		0x00000000
+#define ST0_UX			0x00000020
+#define ST0_SX			0x00000040
+#define ST0_KX			0x00000080
+#define ST0_DE			0x00010000
+#define ST0_CE			0x00020000
+
+/*
+ * Setting c0_status.co enables Hit_Writeback and Hit_Writeback_Invalidate
+ * cacheops in userspace.  This bit exists only on RM7000 and RM9000
+ * processors.
+ */
+#define ST0_CO			0x08000000
+
+/*
+ * Bitfields in the R[23]000 cp0 status register.
+ */
+#define ST0_IEC			0x00000001
+#define ST0_KUC			0x00000002
+#define ST0_IEP			0x00000004
+#define ST0_KUP			0x00000008
+#define ST0_IEO			0x00000010
+#define ST0_KUO			0x00000020
+/* bits 6 & 7 are reserved on R[23]000 */
+#define ST0_ISC			0x00010000
+#define ST0_SWC			0x00020000
+#define ST0_CM			0x00080000
+
+/*
+ * Bits specific to the R4640/R4650
+ */
+#define ST0_UM			(_ULCAST_(1) <<	 4)
+#define ST0_IL			(_ULCAST_(1) << 23)
+#define ST0_DL			(_ULCAST_(1) << 24)
+
+/*
+ * Enable the MIPS MDMX and DSP ASEs
+ */
+#define ST0_MX			0x01000000
+
+/*
+ * Status register bits available in all MIPS CPUs.
+ */
+#define ST0_IM			0x0000ff00
+#define	 STATUSB_IP0		8
+#define	 STATUSF_IP0		(_ULCAST_(1) <<	 8)
+#define	 STATUSB_IP1		9
+#define	 STATUSF_IP1		(_ULCAST_(1) <<	 9)
+#define	 STATUSB_IP2		10
+#define	 STATUSF_IP2		(_ULCAST_(1) << 10)
+#define	 STATUSB_IP3		11
+#define	 STATUSF_IP3		(_ULCAST_(1) << 11)
+#define	 STATUSB_IP4		12
+#define	 STATUSF_IP4		(_ULCAST_(1) << 12)
+#define	 STATUSB_IP5		13
+#define	 STATUSF_IP5		(_ULCAST_(1) << 13)
+#define	 STATUSB_IP6		14
+#define	 STATUSF_IP6		(_ULCAST_(1) << 14)
+#define	 STATUSB_IP7		15
+#define	 STATUSF_IP7		(_ULCAST_(1) << 15)
+#define	 STATUSB_IP8		0
+#define	 STATUSF_IP8		(_ULCAST_(1) <<	 0)
+#define	 STATUSB_IP9		1
+#define	 STATUSF_IP9		(_ULCAST_(1) <<	 1)
+#define	 STATUSB_IP10		2
+#define	 STATUSF_IP10		(_ULCAST_(1) <<	 2)
+#define	 STATUSB_IP11		3
+#define	 STATUSF_IP11		(_ULCAST_(1) <<	 3)
+#define	 STATUSB_IP12		4
+#define	 STATUSF_IP12		(_ULCAST_(1) <<	 4)
+#define	 STATUSB_IP13		5
+#define	 STATUSF_IP13		(_ULCAST_(1) <<	 5)
+#define	 STATUSB_IP14		6
+#define	 STATUSF_IP14		(_ULCAST_(1) <<	 6)
+#define	 STATUSB_IP15		7
+#define	 STATUSF_IP15		(_ULCAST_(1) <<	 7)
+#define ST0_CH			0x00040000
+#define ST0_NMI			0x00080000
+#define ST0_SR			0x00100000
+#define ST0_TS			0x00200000
+#define ST0_BEV			0x00400000
+#define ST0_RE			0x02000000
+#define ST0_FR			0x04000000
+#define ST0_CU			0xf0000000
+#define ST0_CU0			0x10000000
+#define ST0_CU1			0x20000000
+#define ST0_CU2			0x40000000
+#define ST0_CU3			0x80000000
+#define ST0_XX			0x80000000	/* MIPS IV naming */
+
+/* in-kernel enabled CUs */
+#ifdef CONFIG_CPU_LOONGSON64
+#define ST0_KERNEL_CUMASK      (ST0_CU0 | ST0_CU2)
+#else
+#define ST0_KERNEL_CUMASK      ST0_CU0
+#endif
+
+/*
+ * Bitfields and bit numbers in the coprocessor 0 IntCtl register. (MIPSR2)
+ */
+#define INTCTLB_IPFDC		23
+#define INTCTLF_IPFDC		(_ULCAST_(7) << INTCTLB_IPFDC)
+#define INTCTLB_IPPCI		26
+#define INTCTLF_IPPCI		(_ULCAST_(7) << INTCTLB_IPPCI)
+#define INTCTLB_IPTI		29
+#define INTCTLF_IPTI		(_ULCAST_(7) << INTCTLB_IPTI)
+
+/*
+ * Bitfields and bit numbers in the coprocessor 0 cause register.
+ *
+ * Refer to your MIPS R4xx0 manual, chapter 5 for explanation.
+ */
+#define CAUSEB_EXCCODE		2
+#define CAUSEF_EXCCODE		(_ULCAST_(31)  <<  2)
+#define CAUSEB_IP		8
+#define CAUSEF_IP		(_ULCAST_(255) <<  8)
+#define	 CAUSEB_IP0		8
+#define	 CAUSEF_IP0		(_ULCAST_(1)   <<  8)
+#define	 CAUSEB_IP1		9
+#define	 CAUSEF_IP1		(_ULCAST_(1)   <<  9)
+#define	 CAUSEB_IP2		10
+#define	 CAUSEF_IP2		(_ULCAST_(1)   << 10)
+#define	 CAUSEB_IP3		11
+#define	 CAUSEF_IP3		(_ULCAST_(1)   << 11)
+#define	 CAUSEB_IP4		12
+#define	 CAUSEF_IP4		(_ULCAST_(1)   << 12)
+#define	 CAUSEB_IP5		13
+#define	 CAUSEF_IP5		(_ULCAST_(1)   << 13)
+#define	 CAUSEB_IP6		14
+#define	 CAUSEF_IP6		(_ULCAST_(1)   << 14)
+#define	 CAUSEB_IP7		15
+#define	 CAUSEF_IP7		(_ULCAST_(1)   << 15)
+#define CAUSEB_FDCI		21
+#define CAUSEF_FDCI		(_ULCAST_(1)   << 21)
+#define CAUSEB_WP		22
+#define CAUSEF_WP		(_ULCAST_(1)   << 22)
+#define CAUSEB_IV		23
+#define CAUSEF_IV		(_ULCAST_(1)   << 23)
+#define CAUSEB_PCI		26
+#define CAUSEF_PCI		(_ULCAST_(1)   << 26)
+#define CAUSEB_DC		27
+#define CAUSEF_DC		(_ULCAST_(1)   << 27)
+#define CAUSEB_CE		28
+#define CAUSEF_CE		(_ULCAST_(3)   << 28)
+#define CAUSEB_TI		30
+#define CAUSEF_TI		(_ULCAST_(1)   << 30)
+#define CAUSEB_BD		31
+#define CAUSEF_BD		(_ULCAST_(1)   << 31)
+
+/*
+ * Cause.ExcCode trap codes.
+ */
+#define EXCCODE_INT		0	/* Interrupt pending */
+#define EXCCODE_MOD		1	/* TLB modified fault */
+#define EXCCODE_TLBL		2	/* TLB miss on load or ifetch */
+#define EXCCODE_TLBS		3	/* TLB miss on a store */
+#define EXCCODE_ADEL		4	/* Address error on a load or ifetch */
+#define EXCCODE_ADES		5	/* Address error on a store */
+#define EXCCODE_IBE		6	/* Bus error on an ifetch */
+#define EXCCODE_DBE		7	/* Bus error on a load or store */
+#define EXCCODE_SYS		8	/* System call */
+#define EXCCODE_BP		9	/* Breakpoint */
+#define EXCCODE_RI		10	/* Reserved instruction exception */
+#define EXCCODE_CPU		11	/* Coprocessor unusable */
+#define EXCCODE_OV		12	/* Arithmetic overflow */
+#define EXCCODE_TR		13	/* Trap instruction */
+#define EXCCODE_MSAFPE		14	/* MSA floating point exception */
+#define EXCCODE_FPE		15	/* Floating point exception */
+#define EXCCODE_TLBRI		19	/* TLB Read-Inhibit exception */
+#define EXCCODE_TLBXI		20	/* TLB Execution-Inhibit exception */
+#define EXCCODE_MSADIS		21	/* MSA disabled exception */
+#define EXCCODE_MDMX		22	/* MDMX unusable exception */
+#define EXCCODE_WATCH		23	/* Watch address reference */
+#define EXCCODE_MCHECK		24	/* Machine check */
+#define EXCCODE_THREAD		25	/* Thread exceptions (MT) */
+#define EXCCODE_DSPDIS		26	/* DSP disabled exception */
+#define EXCCODE_GE		27	/* Virtualized guest exception (VZ) */
+#define EXCCODE_CACHEERR	30	/* Parity/ECC occured on a core */
+
+/* Implementation specific trap codes used by MIPS cores */
+#define MIPS_EXCCODE_TLBPAR	16	/* TLB parity error exception */
+
+/* Implementation specific trap codes used by Loongson cores */
+#define LOONGSON_EXCCODE_GSEXC	16	/* Loongson-specific exception */
+
+/*
+ * Bits in the coprocessor 0 config register.
+ */
+/* Generic bits.  */
+#define CONF_CM_CACHABLE_NO_WA		0
+#define CONF_CM_CACHABLE_WA		1
+#define CONF_CM_UNCACHED		2
+#define CONF_CM_CACHABLE_NONCOHERENT	3
+#define CONF_CM_CACHABLE_CE		4
+#define CONF_CM_CACHABLE_COW		5
+#define CONF_CM_CACHABLE_CUW		6
+#define CONF_CM_CACHABLE_ACCELERATED	7
+#define CONF_CM_CMASK			7
+#define CONF_BE			(_ULCAST_(1) << 15)
+
+/* Bits common to various processors.  */
+#define CONF_CU			(_ULCAST_(1) <<	 3)
+#define CONF_DB			(_ULCAST_(1) <<	 4)
+#define CONF_IB			(_ULCAST_(1) <<	 5)
+#define CONF_DC			(_ULCAST_(7) <<	 6)
+#define CONF_IC			(_ULCAST_(7) <<	 9)
+#define CONF_EB			(_ULCAST_(1) << 13)
+#define CONF_EM			(_ULCAST_(1) << 14)
+#define CONF_SM			(_ULCAST_(1) << 16)
+#define CONF_SC			(_ULCAST_(1) << 17)
+#define CONF_EW			(_ULCAST_(3) << 18)
+#define CONF_EP			(_ULCAST_(15)<< 24)
+#define CONF_EC			(_ULCAST_(7) << 28)
+#define CONF_CM			(_ULCAST_(1) << 31)
+
+/* Bits specific to the R4xx0.	*/
+#define R4K_CONF_SW		(_ULCAST_(1) << 20)
+#define R4K_CONF_SS		(_ULCAST_(1) << 21)
+#define R4K_CONF_SB		(_ULCAST_(3) << 22)
+
+/* Bits specific to the R5000.	*/
+#define R5K_CONF_SE		(_ULCAST_(1) << 12)
+#define R5K_CONF_SS		(_ULCAST_(3) << 20)
+
+/* Bits specific to the RM7000.	 */
+#define RM7K_CONF_SE		(_ULCAST_(1) <<	 3)
+#define RM7K_CONF_TE		(_ULCAST_(1) << 12)
+#define RM7K_CONF_CLK		(_ULCAST_(1) << 16)
+#define RM7K_CONF_TC		(_ULCAST_(1) << 17)
+#define RM7K_CONF_SI		(_ULCAST_(3) << 20)
+#define RM7K_CONF_SC		(_ULCAST_(1) << 31)
+
+/* Bits specific to the R10000.	 */
+#define R10K_CONF_DN		(_ULCAST_(3) <<	 3)
+#define R10K_CONF_CT		(_ULCAST_(1) <<	 5)
+#define R10K_CONF_PE		(_ULCAST_(1) <<	 6)
+#define R10K_CONF_PM		(_ULCAST_(3) <<	 7)
+#define R10K_CONF_EC		(_ULCAST_(15)<<	 9)
+#define R10K_CONF_SB		(_ULCAST_(1) << 13)
+#define R10K_CONF_SK		(_ULCAST_(1) << 14)
+#define R10K_CONF_SS		(_ULCAST_(7) << 16)
+#define R10K_CONF_SC		(_ULCAST_(7) << 19)
+#define R10K_CONF_DC		(_ULCAST_(7) << 26)
+#define R10K_CONF_IC		(_ULCAST_(7) << 29)
+
+/* Bits specific to the VR41xx.	 */
+#define VR41_CONF_CS		(_ULCAST_(1) << 12)
+#define VR41_CONF_P4K		(_ULCAST_(1) << 13)
+#define VR41_CONF_BP		(_ULCAST_(1) << 16)
+#define VR41_CONF_M16		(_ULCAST_(1) << 20)
+#define VR41_CONF_AD		(_ULCAST_(1) << 23)
+
+/* Bits specific to the R30xx.	*/
+#define R30XX_CONF_FDM		(_ULCAST_(1) << 19)
+#define R30XX_CONF_REV		(_ULCAST_(1) << 22)
+#define R30XX_CONF_AC		(_ULCAST_(1) << 23)
+#define R30XX_CONF_RF		(_ULCAST_(1) << 24)
+#define R30XX_CONF_HALT		(_ULCAST_(1) << 25)
+#define R30XX_CONF_FPINT	(_ULCAST_(7) << 26)
+#define R30XX_CONF_DBR		(_ULCAST_(1) << 29)
+#define R30XX_CONF_SB		(_ULCAST_(1) << 30)
+#define R30XX_CONF_LOCK		(_ULCAST_(1) << 31)
+
+/* Bits specific to the TX49.  */
+#define TX49_CONF_DC		(_ULCAST_(1) << 16)
+#define TX49_CONF_IC		(_ULCAST_(1) << 17)  /* conflict with CONF_SC */
+#define TX49_CONF_HALT		(_ULCAST_(1) << 18)
+#define TX49_CONF_CWFON		(_ULCAST_(1) << 27)
+
+/* Bits specific to the MIPS32/64 PRA.	*/
+#define MIPS_CONF_VI		(_ULCAST_(1) <<  3)
+#define MIPS_CONF_MT		(_ULCAST_(7) <<	 7)
+#define MIPS_CONF_MT_TLB	(_ULCAST_(1) <<  7)
+#define MIPS_CONF_MT_FTLB	(_ULCAST_(4) <<  7)
+#define MIPS_CONF_AR		(_ULCAST_(7) << 10)
+#define MIPS_CONF_AT		(_ULCAST_(3) << 13)
+#define MIPS_CONF_BE		(_ULCAST_(1) << 15)
+#define MIPS_CONF_BM		(_ULCAST_(1) << 16)
+#define MIPS_CONF_MM		(_ULCAST_(3) << 17)
+#define MIPS_CONF_MM_SYSAD	(_ULCAST_(1) << 17)
+#define MIPS_CONF_MM_FULL	(_ULCAST_(2) << 17)
+#define MIPS_CONF_SB		(_ULCAST_(1) << 21)
+#define MIPS_CONF_UDI		(_ULCAST_(1) << 22)
+#define MIPS_CONF_DSP		(_ULCAST_(1) << 23)
+#define MIPS_CONF_ISP		(_ULCAST_(1) << 24)
+#define MIPS_CONF_KU		(_ULCAST_(3) << 25)
+#define MIPS_CONF_K23		(_ULCAST_(3) << 28)
+#define MIPS_CONF_M		(_ULCAST_(1) << 31)
+
+/*
+ * Bits in the MIPS32/64 PRA coprocessor 0 config registers 1 and above.
+ */
+#define MIPS_CONF1_FP		(_ULCAST_(1) <<	 0)
+#define MIPS_CONF1_EP		(_ULCAST_(1) <<	 1)
+#define MIPS_CONF1_CA		(_ULCAST_(1) <<	 2)
+#define MIPS_CONF1_WR		(_ULCAST_(1) <<	 3)
+#define MIPS_CONF1_PC		(_ULCAST_(1) <<	 4)
+#define MIPS_CONF1_MD		(_ULCAST_(1) <<	 5)
+#define MIPS_CONF1_C2		(_ULCAST_(1) <<	 6)
+#define MIPS_CONF1_DA_SHF	7
+#define MIPS_CONF1_DA_SZ	3
+#define MIPS_CONF1_DA		(_ULCAST_(7) <<	 7)
+#define MIPS_CONF1_DL_SHF	10
+#define MIPS_CONF1_DL_SZ	3
+#define MIPS_CONF1_DL		(_ULCAST_(7) << 10)
+#define MIPS_CONF1_DS_SHF	13
+#define MIPS_CONF1_DS_SZ	3
+#define MIPS_CONF1_DS		(_ULCAST_(7) << 13)
+#define MIPS_CONF1_IA_SHF	16
+#define MIPS_CONF1_IA_SZ	3
+#define MIPS_CONF1_IA		(_ULCAST_(7) << 16)
+#define MIPS_CONF1_IL_SHF	19
+#define MIPS_CONF1_IL_SZ	3
+#define MIPS_CONF1_IL		(_ULCAST_(7) << 19)
+#define MIPS_CONF1_IS_SHF	22
+#define MIPS_CONF1_IS_SZ	3
+#define MIPS_CONF1_IS		(_ULCAST_(7) << 22)
+#define MIPS_CONF1_TLBS_SHIFT   (25)
+#define MIPS_CONF1_TLBS_SIZE    (6)
+#define MIPS_CONF1_TLBS         (_ULCAST_(63) << MIPS_CONF1_TLBS_SHIFT)
+
+#define MIPS_CONF2_SA		(_ULCAST_(15)<<	 0)
+#define MIPS_CONF2_SL		(_ULCAST_(15)<<	 4)
+#define MIPS_CONF2_SS		(_ULCAST_(15)<<	 8)
+#define MIPS_CONF2_SU		(_ULCAST_(15)<< 12)
+#define MIPS_CONF2_TA		(_ULCAST_(15)<< 16)
+#define MIPS_CONF2_TL		(_ULCAST_(15)<< 20)
+#define MIPS_CONF2_TS		(_ULCAST_(15)<< 24)
+#define MIPS_CONF2_TU		(_ULCAST_(7) << 28)
+
+#define MIPS_CONF3_TL		(_ULCAST_(1) <<	 0)
+#define MIPS_CONF3_SM		(_ULCAST_(1) <<	 1)
+#define MIPS_CONF3_MT		(_ULCAST_(1) <<	 2)
+#define MIPS_CONF3_CDMM		(_ULCAST_(1) <<	 3)
+#define MIPS_CONF3_SP		(_ULCAST_(1) <<	 4)
+#define MIPS_CONF3_VINT		(_ULCAST_(1) <<	 5)
+#define MIPS_CONF3_VEIC		(_ULCAST_(1) <<	 6)
+#define MIPS_CONF3_LPA		(_ULCAST_(1) <<	 7)
+#define MIPS_CONF3_ITL		(_ULCAST_(1) <<	 8)
+#define MIPS_CONF3_CTXTC	(_ULCAST_(1) <<	 9)
+#define MIPS_CONF3_DSP		(_ULCAST_(1) << 10)
+#define MIPS_CONF3_DSP2P	(_ULCAST_(1) << 11)
+#define MIPS_CONF3_RXI		(_ULCAST_(1) << 12)
+#define MIPS_CONF3_ULRI		(_ULCAST_(1) << 13)
+#define MIPS_CONF3_ISA		(_ULCAST_(3) << 14)
+#define MIPS_CONF3_ISA_OE	(_ULCAST_(1) << 16)
+#define MIPS_CONF3_MCU		(_ULCAST_(1) << 17)
+#define MIPS_CONF3_MMAR		(_ULCAST_(7) << 18)
+#define MIPS_CONF3_IPLW		(_ULCAST_(3) << 21)
+#define MIPS_CONF3_VZ		(_ULCAST_(1) << 23)
+#define MIPS_CONF3_PW		(_ULCAST_(1) << 24)
+#define MIPS_CONF3_SC		(_ULCAST_(1) << 25)
+#define MIPS_CONF3_BI		(_ULCAST_(1) << 26)
+#define MIPS_CONF3_BP		(_ULCAST_(1) << 27)
+#define MIPS_CONF3_MSA		(_ULCAST_(1) << 28)
+#define MIPS_CONF3_CMGCR	(_ULCAST_(1) << 29)
+#define MIPS_CONF3_BPG		(_ULCAST_(1) << 30)
+
+#define MIPS_CONF4_MMUSIZEEXT_SHIFT	(0)
+#define MIPS_CONF4_MMUSIZEEXT	(_ULCAST_(255) << 0)
+#define MIPS_CONF4_FTLBSETS_SHIFT	(0)
+#define MIPS_CONF4_FTLBSETS	(_ULCAST_(15) << MIPS_CONF4_FTLBSETS_SHIFT)
+#define MIPS_CONF4_FTLBWAYS_SHIFT	(4)
+#define MIPS_CONF4_FTLBWAYS	(_ULCAST_(15) << MIPS_CONF4_FTLBWAYS_SHIFT)
+#define MIPS_CONF4_FTLBPAGESIZE_SHIFT	(8)
+/* bits 10:8 in FTLB-only configurations */
+#define MIPS_CONF4_FTLBPAGESIZE (_ULCAST_(7) << MIPS_CONF4_FTLBPAGESIZE_SHIFT)
+/* bits 12:8 in VTLB-FTLB only configurations */
+#define MIPS_CONF4_VFTLBPAGESIZE (_ULCAST_(31) << MIPS_CONF4_FTLBPAGESIZE_SHIFT)
+#define MIPS_CONF4_MMUEXTDEF	(_ULCAST_(3) << 14)
+#define MIPS_CONF4_MMUEXTDEF_MMUSIZEEXT (_ULCAST_(1) << 14)
+#define MIPS_CONF4_MMUEXTDEF_FTLBSIZEEXT	(_ULCAST_(2) << 14)
+#define MIPS_CONF4_MMUEXTDEF_VTLBSIZEEXT	(_ULCAST_(3) << 14)
+#define MIPS_CONF4_KSCREXIST_SHIFT	(16)
+#define MIPS_CONF4_KSCREXIST	(_ULCAST_(255) << MIPS_CONF4_KSCREXIST_SHIFT)
+#define MIPS_CONF4_VTLBSIZEEXT_SHIFT	(24)
+#define MIPS_CONF4_VTLBSIZEEXT	(_ULCAST_(15) << MIPS_CONF4_VTLBSIZEEXT_SHIFT)
+#define MIPS_CONF4_AE		(_ULCAST_(1) << 28)
+#define MIPS_CONF4_IE		(_ULCAST_(3) << 29)
+#define MIPS_CONF4_TLBINV	(_ULCAST_(2) << 29)
+
+#define MIPS_CONF5_NF		(_ULCAST_(1) << 0)
+#define MIPS_CONF5_UFR		(_ULCAST_(1) << 2)
+#define MIPS_CONF5_MRP		(_ULCAST_(1) << 3)
+#define MIPS_CONF5_LLB		(_ULCAST_(1) << 4)
+#define MIPS_CONF5_MVH		(_ULCAST_(1) << 5)
+#define MIPS_CONF5_VP		(_ULCAST_(1) << 7)
+#define MIPS_CONF5_SBRI		(_ULCAST_(1) << 6)
+#define MIPS_CONF5_FRE		(_ULCAST_(1) << 8)
+#define MIPS_CONF5_UFE		(_ULCAST_(1) << 9)
+#define MIPS_CONF5_CA2		(_ULCAST_(1) << 14)
+#define MIPS_CONF5_MI		(_ULCAST_(1) << 17)
+#define MIPS_CONF5_CRCP		(_ULCAST_(1) << 18)
+#define MIPS_CONF5_MSAEN	(_ULCAST_(1) << 27)
+#define MIPS_CONF5_EVA		(_ULCAST_(1) << 28)
+#define MIPS_CONF5_CV		(_ULCAST_(1) << 29)
+#define MIPS_CONF5_K		(_ULCAST_(1) << 30)
+
+/* Config6 feature bits for proAptiv/P5600 */
+
+/* Jump register cache prediction disable */
+#define MTI_CONF6_JRCD		(_ULCAST_(1) << 0)
+/* MIPSr6 extensions enable */
+#define MTI_CONF6_R6		(_ULCAST_(1) << 2)
+/* IFU Performance Control */
+#define MTI_CONF6_IFUPERFCTL	(_ULCAST_(3) << 10)
+#define MTI_CONF6_SYND		(_ULCAST_(1) << 13)
+/* Sleep state performance counter disable */
+#define MTI_CONF6_SPCD		(_ULCAST_(1) << 14)
+/* proAptiv FTLB on/off bit */
+#define MTI_CONF6_FTLBEN	(_ULCAST_(1) << 15)
+/* Disable load/store bonding */
+#define MTI_CONF6_DLSB		(_ULCAST_(1) << 21)
+/* FTLB probability bits */
+#define MTI_CONF6_FTLBP_SHIFT	(16)
+
+/* Config6 feature bits for Loongson-3 */
+
+/* Loongson-3 internal timer bit */
+#define LOONGSON_CONF6_INTIMER	(_ULCAST_(1) << 6)
+/* Loongson-3 external timer bit */
+#define LOONGSON_CONF6_EXTIMER	(_ULCAST_(1) << 7)
+/* Loongson-3 SFB on/off bit, STFill in manual */
+#define LOONGSON_CONF6_SFBEN	(_ULCAST_(1) << 8)
+/* Loongson-3's LL on exclusive cacheline */
+#define LOONGSON_CONF6_LLEXC	(_ULCAST_(1) << 16)
+/* Loongson-3's SC has a random delay */
+#define LOONGSON_CONF6_SCRAND	(_ULCAST_(1) << 17)
+/* Loongson-3 FTLB on/off bit, VTLBOnly in manual */
+#define LOONGSON_CONF6_FTLBDIS	(_ULCAST_(1) << 22)
+
+#define MIPS_CONF7_WII		(_ULCAST_(1) << 31)
+
+#define MIPS_CONF7_RPS		(_ULCAST_(1) << 2)
+
+#define MIPS_CONF7_IAR		(_ULCAST_(1) << 10)
+#define MIPS_CONF7_AR		(_ULCAST_(1) << 16)
+
+/* Ingenic HPTLB off bits */
+#define XBURST_PAGECTRL_HPTLB_DIS 0xa9000000
+
+/* Ingenic Config7 bits */
+#define MIPS_CONF7_BTB_LOOP_EN	(_ULCAST_(1) << 4)
+
+/* Config7 Bits specific to MIPS Technologies. */
+
+/* Performance counters implemented Per TC */
+#define MTI_CONF7_PTC		(_ULCAST_(1) << 19)
+
+/* WatchLo* register definitions */
+#define MIPS_WATCHLO_IRW	(_ULCAST_(0x7) << 0)
+
+/* WatchHi* register definitions */
+#define MIPS_WATCHHI_M		(_ULCAST_(1) << 31)
+#define MIPS_WATCHHI_G		(_ULCAST_(1) << 30)
+#define MIPS_WATCHHI_WM		(_ULCAST_(0x3) << 28)
+#define MIPS_WATCHHI_WM_R_RVA	(_ULCAST_(0) << 28)
+#define MIPS_WATCHHI_WM_R_GPA	(_ULCAST_(1) << 28)
+#define MIPS_WATCHHI_WM_G_GVA	(_ULCAST_(2) << 28)
+#define MIPS_WATCHHI_EAS	(_ULCAST_(0x3) << 24)
+#define MIPS_WATCHHI_ASID	(_ULCAST_(0xff) << 16)
+#define MIPS_WATCHHI_MASK	(_ULCAST_(0x1ff) << 3)
+#define MIPS_WATCHHI_I		(_ULCAST_(1) << 2)
+#define MIPS_WATCHHI_R		(_ULCAST_(1) << 1)
+#define MIPS_WATCHHI_W		(_ULCAST_(1) << 0)
+#define MIPS_WATCHHI_IRW	(_ULCAST_(0x7) << 0)
+
+/* PerfCnt control register definitions */
+#define MIPS_PERFCTRL_EXL	(_ULCAST_(1) << 0)
+#define MIPS_PERFCTRL_K		(_ULCAST_(1) << 1)
+#define MIPS_PERFCTRL_S		(_ULCAST_(1) << 2)
+#define MIPS_PERFCTRL_U		(_ULCAST_(1) << 3)
+#define MIPS_PERFCTRL_IE	(_ULCAST_(1) << 4)
+#define MIPS_PERFCTRL_EVENT_S	5
+#define MIPS_PERFCTRL_EVENT	(_ULCAST_(0x3ff) << MIPS_PERFCTRL_EVENT_S)
+#define MIPS_PERFCTRL_PCTD	(_ULCAST_(1) << 15)
+#define MIPS_PERFCTRL_EC	(_ULCAST_(0x3) << 23)
+#define MIPS_PERFCTRL_EC_R	(_ULCAST_(0) << 23)
+#define MIPS_PERFCTRL_EC_RI	(_ULCAST_(1) << 23)
+#define MIPS_PERFCTRL_EC_G	(_ULCAST_(2) << 23)
+#define MIPS_PERFCTRL_EC_GRI	(_ULCAST_(3) << 23)
+#define MIPS_PERFCTRL_W		(_ULCAST_(1) << 30)
+#define MIPS_PERFCTRL_M		(_ULCAST_(1) << 31)
+
+/* PerfCnt control register MT extensions used by MIPS cores */
+#define MIPS_PERFCTRL_VPEID_S	16
+#define MIPS_PERFCTRL_VPEID	(_ULCAST_(0xf) << MIPS_PERFCTRL_VPEID_S)
+#define MIPS_PERFCTRL_TCID_S	22
+#define MIPS_PERFCTRL_TCID	(_ULCAST_(0xff) << MIPS_PERFCTRL_TCID_S)
+#define MIPS_PERFCTRL_MT_EN	(_ULCAST_(0x3) << 20)
+#define MIPS_PERFCTRL_MT_EN_ALL	(_ULCAST_(0) << 20)
+#define MIPS_PERFCTRL_MT_EN_VPE	(_ULCAST_(1) << 20)
+#define MIPS_PERFCTRL_MT_EN_TC	(_ULCAST_(2) << 20)
+
+/* PerfCnt control register MT extensions used by BMIPS5000 */
+#define BRCM_PERFCTRL_TC	(_ULCAST_(1) << 30)
+
+/* PerfCnt control register MT extensions used by Netlogic XLR */
+#define XLR_PERFCTRL_ALLTHREADS	(_ULCAST_(1) << 13)
+
+/* MAAR bit definitions */
+#define MIPS_MAAR_VH		(_U64CAST_(1) << 63)
+#define MIPS_MAAR_ADDR		GENMASK_ULL(55, 12)
+#define MIPS_MAAR_ADDR_SHIFT	12
+#define MIPS_MAAR_S		(_ULCAST_(1) << 1)
+#define MIPS_MAAR_VL		(_ULCAST_(1) << 0)
+#ifdef CONFIG_XPA
+#define MIPS_MAAR_V		(MIPS_MAAR_VH | MIPS_MAAR_VL)
+#else
+#define MIPS_MAAR_V		MIPS_MAAR_VL
+#endif
+#define MIPS_MAARX_VH		(_ULCAST_(1) << 31)
+#define MIPS_MAARX_ADDR		0xF
+#define MIPS_MAARX_ADDR_SHIFT	32
+
+/* MAARI bit definitions */
+#define MIPS_MAARI_INDEX	(_ULCAST_(0x3f) << 0)
+
+/* EBase bit definitions */
+#define MIPS_EBASE_CPUNUM_SHIFT	0
+#define MIPS_EBASE_CPUNUM	(_ULCAST_(0x3ff) << 0)
+#define MIPS_EBASE_WG_SHIFT	11
+#define MIPS_EBASE_WG		(_ULCAST_(1) << 11)
+#define MIPS_EBASE_BASE_SHIFT	12
+#define MIPS_EBASE_BASE		(~_ULCAST_((1 << MIPS_EBASE_BASE_SHIFT) - 1))
+
+/* CMGCRBase bit definitions */
+#define MIPS_CMGCRB_BASE	11
+#define MIPS_CMGCRF_BASE	(~_ULCAST_((1 << MIPS_CMGCRB_BASE) - 1))
+
+/* LLAddr bit definitions */
+#define MIPS_LLADDR_LLB_SHIFT	0
+#define MIPS_LLADDR_LLB		(_ULCAST_(1) << MIPS_LLADDR_LLB_SHIFT)
+
+/*
+ * Bits in the MIPS32 Memory Segmentation registers.
+ */
+#define MIPS_SEGCFG_PA_SHIFT	9
+#define MIPS_SEGCFG_PA		(_ULCAST_(127) << MIPS_SEGCFG_PA_SHIFT)
+#define MIPS_SEGCFG_AM_SHIFT	4
+#define MIPS_SEGCFG_AM		(_ULCAST_(7) << MIPS_SEGCFG_AM_SHIFT)
+#define MIPS_SEGCFG_EU_SHIFT	3
+#define MIPS_SEGCFG_EU		(_ULCAST_(1) << MIPS_SEGCFG_EU_SHIFT)
+#define MIPS_SEGCFG_C_SHIFT	0
+#define MIPS_SEGCFG_C		(_ULCAST_(7) << MIPS_SEGCFG_C_SHIFT)
+
+#define MIPS_SEGCFG_UUSK	_ULCAST_(7)
+#define MIPS_SEGCFG_USK		_ULCAST_(5)
+#define MIPS_SEGCFG_MUSUK	_ULCAST_(4)
+#define MIPS_SEGCFG_MUSK	_ULCAST_(3)
+#define MIPS_SEGCFG_MSK		_ULCAST_(2)
+#define MIPS_SEGCFG_MK		_ULCAST_(1)
+#define MIPS_SEGCFG_UK		_ULCAST_(0)
+
+#define MIPS_PWFIELD_GDI_SHIFT	24
+#define MIPS_PWFIELD_GDI_MASK	0x3f000000
+#define MIPS_PWFIELD_UDI_SHIFT	18
+#define MIPS_PWFIELD_UDI_MASK	0x00fc0000
+#define MIPS_PWFIELD_MDI_SHIFT	12
+#define MIPS_PWFIELD_MDI_MASK	0x0003f000
+#define MIPS_PWFIELD_PTI_SHIFT	6
+#define MIPS_PWFIELD_PTI_MASK	0x00000fc0
+#define MIPS_PWFIELD_PTEI_SHIFT	0
+#define MIPS_PWFIELD_PTEI_MASK	0x0000003f
+
+#define MIPS_PWSIZE_PS_SHIFT	30
+#define MIPS_PWSIZE_PS_MASK	0x40000000
+#define MIPS_PWSIZE_GDW_SHIFT	24
+#define MIPS_PWSIZE_GDW_MASK	0x3f000000
+#define MIPS_PWSIZE_UDW_SHIFT	18
+#define MIPS_PWSIZE_UDW_MASK	0x00fc0000
+#define MIPS_PWSIZE_MDW_SHIFT	12
+#define MIPS_PWSIZE_MDW_MASK	0x0003f000
+#define MIPS_PWSIZE_PTW_SHIFT	6
+#define MIPS_PWSIZE_PTW_MASK	0x00000fc0
+#define MIPS_PWSIZE_PTEW_SHIFT	0
+#define MIPS_PWSIZE_PTEW_MASK	0x0000003f
+
+#define MIPS_PWCTL_PWEN_SHIFT	31
+#define MIPS_PWCTL_PWEN_MASK	0x80000000
+#define MIPS_PWCTL_XK_SHIFT	28
+#define MIPS_PWCTL_XK_MASK	0x10000000
+#define MIPS_PWCTL_XS_SHIFT	27
+#define MIPS_PWCTL_XS_MASK	0x08000000
+#define MIPS_PWCTL_XU_SHIFT	26
+#define MIPS_PWCTL_XU_MASK	0x04000000
+#define MIPS_PWCTL_DPH_SHIFT	7
+#define MIPS_PWCTL_DPH_MASK	0x00000080
+#define MIPS_PWCTL_HUGEPG_SHIFT	6
+#define MIPS_PWCTL_HUGEPG_MASK	0x00000060
+#define MIPS_PWCTL_PSN_SHIFT	0
+#define MIPS_PWCTL_PSN_MASK	0x0000003f
+
+/* GuestCtl0 fields */
+#define MIPS_GCTL0_GM_SHIFT	31
+#define MIPS_GCTL0_GM		(_ULCAST_(1) << MIPS_GCTL0_GM_SHIFT)
+#define MIPS_GCTL0_RI_SHIFT	30
+#define MIPS_GCTL0_RI		(_ULCAST_(1) << MIPS_GCTL0_RI_SHIFT)
+#define MIPS_GCTL0_MC_SHIFT	29
+#define MIPS_GCTL0_MC		(_ULCAST_(1) << MIPS_GCTL0_MC_SHIFT)
+#define MIPS_GCTL0_CP0_SHIFT	28
+#define MIPS_GCTL0_CP0		(_ULCAST_(1) << MIPS_GCTL0_CP0_SHIFT)
+#define MIPS_GCTL0_AT_SHIFT	26
+#define MIPS_GCTL0_AT		(_ULCAST_(0x3) << MIPS_GCTL0_AT_SHIFT)
+#define MIPS_GCTL0_GT_SHIFT	25
+#define MIPS_GCTL0_GT		(_ULCAST_(1) << MIPS_GCTL0_GT_SHIFT)
+#define MIPS_GCTL0_CG_SHIFT	24
+#define MIPS_GCTL0_CG		(_ULCAST_(1) << MIPS_GCTL0_CG_SHIFT)
+#define MIPS_GCTL0_CF_SHIFT	23
+#define MIPS_GCTL0_CF		(_ULCAST_(1) << MIPS_GCTL0_CF_SHIFT)
+#define MIPS_GCTL0_G1_SHIFT	22
+#define MIPS_GCTL0_G1		(_ULCAST_(1) << MIPS_GCTL0_G1_SHIFT)
+#define MIPS_GCTL0_G0E_SHIFT	19
+#define MIPS_GCTL0_G0E		(_ULCAST_(1) << MIPS_GCTL0_G0E_SHIFT)
+#define MIPS_GCTL0_PT_SHIFT	18
+#define MIPS_GCTL0_PT		(_ULCAST_(1) << MIPS_GCTL0_PT_SHIFT)
+#define MIPS_GCTL0_RAD_SHIFT	9
+#define MIPS_GCTL0_RAD		(_ULCAST_(1) << MIPS_GCTL0_RAD_SHIFT)
+#define MIPS_GCTL0_DRG_SHIFT	8
+#define MIPS_GCTL0_DRG		(_ULCAST_(1) << MIPS_GCTL0_DRG_SHIFT)
+#define MIPS_GCTL0_G2_SHIFT	7
+#define MIPS_GCTL0_G2		(_ULCAST_(1) << MIPS_GCTL0_G2_SHIFT)
+#define MIPS_GCTL0_GEXC_SHIFT	2
+#define MIPS_GCTL0_GEXC		(_ULCAST_(0x1f) << MIPS_GCTL0_GEXC_SHIFT)
+#define MIPS_GCTL0_SFC2_SHIFT	1
+#define MIPS_GCTL0_SFC2		(_ULCAST_(1) << MIPS_GCTL0_SFC2_SHIFT)
+#define MIPS_GCTL0_SFC1_SHIFT	0
+#define MIPS_GCTL0_SFC1		(_ULCAST_(1) << MIPS_GCTL0_SFC1_SHIFT)
+
+/* GuestCtl0.AT Guest address translation control */
+#define MIPS_GCTL0_AT_ROOT	1  /* Guest MMU under Root control */
+#define MIPS_GCTL0_AT_GUEST	3  /* Guest MMU under Guest control */
+
+/* GuestCtl0.GExcCode Hypervisor exception cause codes */
+#define MIPS_GCTL0_GEXC_GPSI	0  /* Guest Privileged Sensitive Instruction */
+#define MIPS_GCTL0_GEXC_GSFC	1  /* Guest Software Field Change */
+#define MIPS_GCTL0_GEXC_HC	2  /* Hypercall */
+#define MIPS_GCTL0_GEXC_GRR	3  /* Guest Reserved Instruction Redirect */
+#define MIPS_GCTL0_GEXC_GVA	8  /* Guest Virtual Address available */
+#define MIPS_GCTL0_GEXC_GHFC	9  /* Guest Hardware Field Change */
+#define MIPS_GCTL0_GEXC_GPA	10 /* Guest Physical Address available */
+
+/* GuestCtl0Ext fields */
+#define MIPS_GCTL0EXT_RPW_SHIFT	8
+#define MIPS_GCTL0EXT_RPW	(_ULCAST_(0x3) << MIPS_GCTL0EXT_RPW_SHIFT)
+#define MIPS_GCTL0EXT_NCC_SHIFT	6
+#define MIPS_GCTL0EXT_NCC	(_ULCAST_(0x3) << MIPS_GCTL0EXT_NCC_SHIFT)
+#define MIPS_GCTL0EXT_CGI_SHIFT	4
+#define MIPS_GCTL0EXT_CGI	(_ULCAST_(1) << MIPS_GCTL0EXT_CGI_SHIFT)
+#define MIPS_GCTL0EXT_FCD_SHIFT	3
+#define MIPS_GCTL0EXT_FCD	(_ULCAST_(1) << MIPS_GCTL0EXT_FCD_SHIFT)
+#define MIPS_GCTL0EXT_OG_SHIFT	2
+#define MIPS_GCTL0EXT_OG	(_ULCAST_(1) << MIPS_GCTL0EXT_OG_SHIFT)
+#define MIPS_GCTL0EXT_BG_SHIFT	1
+#define MIPS_GCTL0EXT_BG	(_ULCAST_(1) << MIPS_GCTL0EXT_BG_SHIFT)
+#define MIPS_GCTL0EXT_MG_SHIFT	0
+#define MIPS_GCTL0EXT_MG	(_ULCAST_(1) << MIPS_GCTL0EXT_MG_SHIFT)
+
+/* GuestCtl0Ext.RPW Root page walk configuration */
+#define MIPS_GCTL0EXT_RPW_BOTH	0  /* Root PW for GPA->RPA and RVA->RPA */
+#define MIPS_GCTL0EXT_RPW_GPA	2  /* Root PW for GPA->RPA */
+#define MIPS_GCTL0EXT_RPW_RVA	3  /* Root PW for RVA->RPA */
+
+/* GuestCtl0Ext.NCC Nested cache coherency attributes */
+#define MIPS_GCTL0EXT_NCC_IND	0  /* Guest CCA independent of Root CCA */
+#define MIPS_GCTL0EXT_NCC_MOD	1  /* Guest CCA modified by Root CCA */
+
+/* GuestCtl1 fields */
+#define MIPS_GCTL1_ID_SHIFT	0
+#define MIPS_GCTL1_ID_WIDTH	8
+#define MIPS_GCTL1_ID		(_ULCAST_(0xff) << MIPS_GCTL1_ID_SHIFT)
+#define MIPS_GCTL1_RID_SHIFT	16
+#define MIPS_GCTL1_RID_WIDTH	8
+#define MIPS_GCTL1_RID		(_ULCAST_(0xff) << MIPS_GCTL1_RID_SHIFT)
+#define MIPS_GCTL1_EID_SHIFT	24
+#define MIPS_GCTL1_EID_WIDTH	8
+#define MIPS_GCTL1_EID		(_ULCAST_(0xff) << MIPS_GCTL1_EID_SHIFT)
+
+/* GuestID reserved for root context */
+#define MIPS_GCTL1_ROOT_GUESTID	0
+
+/* CDMMBase register bit definitions */
+#define MIPS_CDMMBASE_SIZE_SHIFT 0
+#define MIPS_CDMMBASE_SIZE	(_ULCAST_(511) << MIPS_CDMMBASE_SIZE_SHIFT)
+#define MIPS_CDMMBASE_CI	(_ULCAST_(1) << 9)
+#define MIPS_CDMMBASE_EN	(_ULCAST_(1) << 10)
+#define MIPS_CDMMBASE_ADDR_SHIFT 11
+#define MIPS_CDMMBASE_ADDR_START 15
+
+/* RDHWR register numbers */
+#define MIPS_HWR_CPUNUM		0	/* CPU number */
+#define MIPS_HWR_SYNCISTEP	1	/* SYNCI step size */
+#define MIPS_HWR_CC		2	/* Cycle counter */
+#define MIPS_HWR_CCRES		3	/* Cycle counter resolution */
+#define MIPS_HWR_ULR		29	/* UserLocal */
+#define MIPS_HWR_IMPL1		30	/* Implementation dependent */
+#define MIPS_HWR_IMPL2		31	/* Implementation dependent */
+
+/* Bits in HWREna register */
+#define MIPS_HWRENA_CPUNUM	(_ULCAST_(1) << MIPS_HWR_CPUNUM)
+#define MIPS_HWRENA_SYNCISTEP	(_ULCAST_(1) << MIPS_HWR_SYNCISTEP)
+#define MIPS_HWRENA_CC		(_ULCAST_(1) << MIPS_HWR_CC)
+#define MIPS_HWRENA_CCRES	(_ULCAST_(1) << MIPS_HWR_CCRES)
+#define MIPS_HWRENA_ULR		(_ULCAST_(1) << MIPS_HWR_ULR)
+#define MIPS_HWRENA_IMPL1	(_ULCAST_(1) << MIPS_HWR_IMPL1)
+#define MIPS_HWRENA_IMPL2	(_ULCAST_(1) << MIPS_HWR_IMPL2)
+
+/*
+ * Bitfields in the TX39 family CP0 Configuration Register 3
+ */
+#define TX39_CONF_ICS_SHIFT	19
+#define TX39_CONF_ICS_MASK	0x00380000
+#define TX39_CONF_ICS_1KB	0x00000000
+#define TX39_CONF_ICS_2KB	0x00080000
+#define TX39_CONF_ICS_4KB	0x00100000
+#define TX39_CONF_ICS_8KB	0x00180000
+#define TX39_CONF_ICS_16KB	0x00200000
+
+#define TX39_CONF_DCS_SHIFT	16
+#define TX39_CONF_DCS_MASK	0x00070000
+#define TX39_CONF_DCS_1KB	0x00000000
+#define TX39_CONF_DCS_2KB	0x00010000
+#define TX39_CONF_DCS_4KB	0x00020000
+#define TX39_CONF_DCS_8KB	0x00030000
+#define TX39_CONF_DCS_16KB	0x00040000
+
+#define TX39_CONF_CWFON		0x00004000
+#define TX39_CONF_WBON		0x00002000
+#define TX39_CONF_RF_SHIFT	10
+#define TX39_CONF_RF_MASK	0x00000c00
+#define TX39_CONF_DOZE		0x00000200
+#define TX39_CONF_HALT		0x00000100
+#define TX39_CONF_LOCK		0x00000080
+#define TX39_CONF_ICE		0x00000020
+#define TX39_CONF_DCE		0x00000010
+#define TX39_CONF_IRSIZE_SHIFT	2
+#define TX39_CONF_IRSIZE_MASK	0x0000000c
+#define TX39_CONF_DRSIZE_SHIFT	0
+#define TX39_CONF_DRSIZE_MASK	0x00000003
+
+/*
+ * Interesting Bits in the R10K CP0 Branch Diagnostic Register
+ */
+/* Disable Branch Target Address Cache */
+#define R10K_DIAG_D_BTAC	(_ULCAST_(1) << 27)
+/* Enable Branch Prediction Global History */
+#define R10K_DIAG_E_GHIST	(_ULCAST_(1) << 26)
+/* Disable Branch Return Cache */
+#define R10K_DIAG_D_BRC		(_ULCAST_(1) << 22)
+
+/* Flush BTB */
+#define LOONGSON_DIAG_BTB	(_ULCAST_(1) << 1)
+/* Flush ITLB */
+#define LOONGSON_DIAG_ITLB	(_ULCAST_(1) << 2)
+/* Flush DTLB */
+#define LOONGSON_DIAG_DTLB	(_ULCAST_(1) << 3)
+/* Allow some CACHE instructions (CACHE0, 1, 3, 21 and 23) in user mode */
+#define LOONGSON_DIAG_UCAC	(_ULCAST_(1) << 8)
+/* Flush VTLB */
+#define LOONGSON_DIAG_VTLB	(_ULCAST_(1) << 12)
+/* Flush FTLB */
+#define LOONGSON_DIAG_FTLB	(_ULCAST_(1) << 13)
+
+/*
+ * Diag1 (GSCause in Loongson-speak) fields
+ */
+/* Loongson-specific exception code (GSExcCode) */
+#define LOONGSON_DIAG1_EXCCODE_SHIFT	2
+#define LOONGSON_DIAG1_EXCCODE		GENMASK(6, 2)
+
+/* CvmCtl register field definitions */
+#define CVMCTL_IPPCI_SHIFT	7
+#define CVMCTL_IPPCI		(_U64CAST_(0x7) << CVMCTL_IPPCI_SHIFT)
+#define CVMCTL_IPTI_SHIFT	4
+#define CVMCTL_IPTI		(_U64CAST_(0x7) << CVMCTL_IPTI_SHIFT)
+
+/* CvmMemCtl2 register field definitions */
+#define CVMMEMCTL2_INHIBITTS	(_U64CAST_(1) << 17)
+
+/* CvmVMConfig register field definitions */
+#define CVMVMCONF_DGHT		(_U64CAST_(1) << 60)
+#define CVMVMCONF_MMUSIZEM1_S	12
+#define CVMVMCONF_MMUSIZEM1	(_U64CAST_(0xff) << CVMVMCONF_MMUSIZEM1_S)
+#define CVMVMCONF_RMMUSIZEM1_S	0
+#define CVMVMCONF_RMMUSIZEM1	(_U64CAST_(0xff) << CVMVMCONF_RMMUSIZEM1_S)
+
+/* Debug register field definitions */
+#define MIPS_DEBUG_DBP_SHIFT	1
+#define MIPS_DEBUG_DBP		(_ULCAST_(1) << MIPS_DEBUG_DBP_SHIFT)
+
+/*
+ * Coprocessor 1 (FPU) register names
+ */
+#define CP1_REVISION	$0
+#define CP1_UFR		$1
+#define CP1_UNFR	$4
+#define CP1_FCCR	$25
+#define CP1_FEXR	$26
+#define CP1_FENR	$28
+#define CP1_STATUS	$31
+
+
+/*
+ * Bits in the MIPS32/64 coprocessor 1 (FPU) revision register.
+ */
+#define MIPS_FPIR_S		(_ULCAST_(1) << 16)
+#define MIPS_FPIR_D		(_ULCAST_(1) << 17)
+#define MIPS_FPIR_PS		(_ULCAST_(1) << 18)
+#define MIPS_FPIR_3D		(_ULCAST_(1) << 19)
+#define MIPS_FPIR_W		(_ULCAST_(1) << 20)
+#define MIPS_FPIR_L		(_ULCAST_(1) << 21)
+#define MIPS_FPIR_F64		(_ULCAST_(1) << 22)
+#define MIPS_FPIR_HAS2008	(_ULCAST_(1) << 23)
+#define MIPS_FPIR_UFRP		(_ULCAST_(1) << 28)
+#define MIPS_FPIR_FREP		(_ULCAST_(1) << 29)
+
+/*
+ * Bits in the MIPS32/64 coprocessor 1 (FPU) condition codes register.
+ */
+#define MIPS_FCCR_CONDX_S	0
+#define MIPS_FCCR_CONDX		(_ULCAST_(255) << MIPS_FCCR_CONDX_S)
+#define MIPS_FCCR_COND0_S	0
+#define MIPS_FCCR_COND0		(_ULCAST_(1) << MIPS_FCCR_COND0_S)
+#define MIPS_FCCR_COND1_S	1
+#define MIPS_FCCR_COND1		(_ULCAST_(1) << MIPS_FCCR_COND1_S)
+#define MIPS_FCCR_COND2_S	2
+#define MIPS_FCCR_COND2		(_ULCAST_(1) << MIPS_FCCR_COND2_S)
+#define MIPS_FCCR_COND3_S	3
+#define MIPS_FCCR_COND3		(_ULCAST_(1) << MIPS_FCCR_COND3_S)
+#define MIPS_FCCR_COND4_S	4
+#define MIPS_FCCR_COND4		(_ULCAST_(1) << MIPS_FCCR_COND4_S)
+#define MIPS_FCCR_COND5_S	5
+#define MIPS_FCCR_COND5		(_ULCAST_(1) << MIPS_FCCR_COND5_S)
+#define MIPS_FCCR_COND6_S	6
+#define MIPS_FCCR_COND6		(_ULCAST_(1) << MIPS_FCCR_COND6_S)
+#define MIPS_FCCR_COND7_S	7
+#define MIPS_FCCR_COND7		(_ULCAST_(1) << MIPS_FCCR_COND7_S)
+
+/*
+ * Bits in the MIPS32/64 coprocessor 1 (FPU) enables register.
+ */
+#define MIPS_FENR_FS_S		2
+#define MIPS_FENR_FS		(_ULCAST_(1) << MIPS_FENR_FS_S)
+
+/*
+ * FPU Status Register Values
+ */
+#define FPU_CSR_COND_S	23					/* $fcc0 */
+#define FPU_CSR_COND	(_ULCAST_(1) << FPU_CSR_COND_S)
+
+#define FPU_CSR_FS_S	24		/* flush denormalised results to 0 */
+#define FPU_CSR_FS	(_ULCAST_(1) << FPU_CSR_FS_S)
+
+#define FPU_CSR_CONDX_S	25					/* $fcc[7:1] */
+#define FPU_CSR_CONDX	(_ULCAST_(127) << FPU_CSR_CONDX_S)
+#define FPU_CSR_COND1_S	25					/* $fcc1 */
+#define FPU_CSR_COND1	(_ULCAST_(1) << FPU_CSR_COND1_S)
+#define FPU_CSR_COND2_S	26					/* $fcc2 */
+#define FPU_CSR_COND2	(_ULCAST_(1) << FPU_CSR_COND2_S)
+#define FPU_CSR_COND3_S	27					/* $fcc3 */
+#define FPU_CSR_COND3	(_ULCAST_(1) << FPU_CSR_COND3_S)
+#define FPU_CSR_COND4_S	28					/* $fcc4 */
+#define FPU_CSR_COND4	(_ULCAST_(1) << FPU_CSR_COND4_S)
+#define FPU_CSR_COND5_S	29					/* $fcc5 */
+#define FPU_CSR_COND5	(_ULCAST_(1) << FPU_CSR_COND5_S)
+#define FPU_CSR_COND6_S	30					/* $fcc6 */
+#define FPU_CSR_COND6	(_ULCAST_(1) << FPU_CSR_COND6_S)
+#define FPU_CSR_COND7_S	31					/* $fcc7 */
+#define FPU_CSR_COND7	(_ULCAST_(1) << FPU_CSR_COND7_S)
+
+/*
+ * Bits 22:20 of the FPU Status Register will be read as 0,
+ * and should be written as zero.
+ * MAC2008 was removed in Release 5 so we still treat it as
+ * reserved.
+ */
+#define FPU_CSR_RSVD	(_ULCAST_(7) << 20)
+
+#define FPU_CSR_MAC2008	(_ULCAST_(1) << 20)
+#define FPU_CSR_ABS2008	(_ULCAST_(1) << 19)
+#define FPU_CSR_NAN2008	(_ULCAST_(1) << 18)
+
+/*
+ * X the exception cause indicator
+ * E the exception enable
+ * S the sticky/flag bit
+*/
+#define FPU_CSR_ALL_X	0x0003f000
+#define FPU_CSR_UNI_X	0x00020000
+#define FPU_CSR_INV_X	0x00010000
+#define FPU_CSR_DIV_X	0x00008000
+#define FPU_CSR_OVF_X	0x00004000
+#define FPU_CSR_UDF_X	0x00002000
+#define FPU_CSR_INE_X	0x00001000
+
+#define FPU_CSR_ALL_E	0x00000f80
+#define FPU_CSR_INV_E	0x00000800
+#define FPU_CSR_DIV_E	0x00000400
+#define FPU_CSR_OVF_E	0x00000200
+#define FPU_CSR_UDF_E	0x00000100
+#define FPU_CSR_INE_E	0x00000080
+
+#define FPU_CSR_ALL_S	0x0000007c
+#define FPU_CSR_INV_S	0x00000040
+#define FPU_CSR_DIV_S	0x00000020
+#define FPU_CSR_OVF_S	0x00000010
+#define FPU_CSR_UDF_S	0x00000008
+#define FPU_CSR_INE_S	0x00000004
+
+/* Bits 0 and 1 of FPU Status Register specify the rounding mode */
+#define FPU_CSR_RM	0x00000003
+#define FPU_CSR_RN	0x0	/* nearest */
+#define FPU_CSR_RZ	0x1	/* towards zero */
+#define FPU_CSR_RU	0x2	/* towards +Infinity */
+#define FPU_CSR_RD	0x3	/* towards -Infinity */
+
+
+#ifndef __ASSEMBLY__
+
+/*
+ * Macros for handling the ISA mode bit for MIPS16 and microMIPS.
+ */
+#if defined(CONFIG_SYS_SUPPORTS_MIPS16) || \
+    defined(CONFIG_SYS_SUPPORTS_MICROMIPS)
+#define get_isa16_mode(x)		((x) & 0x1)
+#define msk_isa16_mode(x)		((x) & ~0x1)
+#define set_isa16_mode(x)		do { (x) |= 0x1; } while(0)
+#else
+#define get_isa16_mode(x)		0
+#define msk_isa16_mode(x)		(x)
+#define set_isa16_mode(x)		do { } while(0)
+#endif
+
+/*
+ * microMIPS instructions can be 16-bit or 32-bit in length. This
+ * returns a 1 if the instruction is 16-bit and a 0 if 32-bit.
+ */
+static inline int mm_insn_16bit(u16 insn)
+{
+	u16 opcode = (insn >> 10) & 0x7;
+
+	return (opcode >= 1 && opcode <= 3) ? 1 : 0;
+}
+
+/*
+ * Helper macros for generating raw instruction encodings in inline asm.
+ */
+#ifdef CONFIG_CPU_MICROMIPS
+#define _ASM_INSN16_IF_MM(_enc)			\
+	".insn\n\t"				\
+	".hword (" #_enc ")\n\t"
+#define _ASM_INSN32_IF_MM(_enc)			\
+	".insn\n\t"				\
+	".hword ((" #_enc ") >> 16)\n\t"	\
+	".hword ((" #_enc ") & 0xffff)\n\t"
+#else
+#define _ASM_INSN_IF_MIPS(_enc)			\
+	".insn\n\t"				\
+	".word (" #_enc ")\n\t"
+#endif
+
+#ifndef _ASM_INSN16_IF_MM
+#define _ASM_INSN16_IF_MM(_enc)
+#endif
+#ifndef _ASM_INSN32_IF_MM
+#define _ASM_INSN32_IF_MM(_enc)
+#endif
+#ifndef _ASM_INSN_IF_MIPS
+#define _ASM_INSN_IF_MIPS(_enc)
+#endif
+
+/*
+ * parse_r var, r - Helper assembler macro for parsing register names.
+ *
+ * This converts the register name in $n form provided in \r to the
+ * corresponding register number, which is assigned to the variable \var. It is
+ * needed to allow explicit encoding of instructions in inline assembly where
+ * registers are chosen by the compiler in $n form, allowing us to avoid using
+ * fixed register numbers.
+ *
+ * It also allows newer instructions (not implemented by the assembler) to be
+ * transparently implemented using assembler macros, instead of needing separate
+ * cases depending on toolchain support.
+ *
+ * Simple usage example:
+ * __asm__ __volatile__("parse_r __rt, %0\n\t"
+ *			".insn\n\t"
+ *			"# di    %0\n\t"
+ *			".word   (0x41606000 | (__rt << 16))"
+ *			: "=r" (status);
+ */
+
+/* Match an individual register number and assign to \var */
+#define _IFC_REG(n)				\
+	".ifc	\\r, $" #n "\n\t"		\
+	"\\var	= " #n "\n\t"			\
+	".endif\n\t"
+
+#define _ASM_SET_PARSE_R						\
+	".macro	parse_r var r\n\t"					\
+	"\\var	= -1\n\t"						\
+	_IFC_REG(0)  _IFC_REG(1)  _IFC_REG(2)  _IFC_REG(3)		\
+	_IFC_REG(4)  _IFC_REG(5)  _IFC_REG(6)  _IFC_REG(7)		\
+	_IFC_REG(8)  _IFC_REG(9)  _IFC_REG(10) _IFC_REG(11)		\
+	_IFC_REG(12) _IFC_REG(13) _IFC_REG(14) _IFC_REG(15)		\
+	_IFC_REG(16) _IFC_REG(17) _IFC_REG(18) _IFC_REG(19)		\
+	_IFC_REG(20) _IFC_REG(21) _IFC_REG(22) _IFC_REG(23)		\
+	_IFC_REG(24) _IFC_REG(25) _IFC_REG(26) _IFC_REG(27)		\
+	_IFC_REG(28) _IFC_REG(29) _IFC_REG(30) _IFC_REG(31)		\
+	".iflt	\\var\n\t"						\
+	".error	\"Unable to parse register name \\r\"\n\t"		\
+	".endif\n\t"							\
+	".endm\n\t"
+#define _ASM_UNSET_PARSE_R ".purgem parse_r\n\t"
+
+/*
+ * C macros for generating assembler macros for common instruction formats.
+ *
+ * The names of the operands can be chosen by the caller, and the encoding of
+ * register operand \<Rn> is assigned to __<Rn> where it can be accessed from
+ * the ENC encodings.
+ */
+
+/* Instructions with 1 register operand & 1 immediate operand */
+#define _ASM_MACRO_1R1I(OP, R1, I2, ENC)				\
+		".macro	" #OP " " #R1 ", " #I2 "\n\t"			\
+		_ASM_SET_PARSE_R					\
+		"parse_r __" #R1 ", \\" #R1 "\n\t"			\
+		ENC							\
+		_ASM_UNSET_PARSE_R					\
+		".endm\n\t"
+
+/* Instructions with 2 register operands */
+#define _ASM_MACRO_2R(OP, R1, R2, ENC)					\
+		".macro	" #OP " " #R1 ", " #R2 "\n\t"			\
+		_ASM_SET_PARSE_R					\
+		"parse_r __" #R1 ", \\" #R1 "\n\t"			\
+		"parse_r __" #R2 ", \\" #R2 "\n\t"			\
+		ENC							\
+		_ASM_UNSET_PARSE_R					\
+		".endm\n\t"
+
+/* Instructions with 3 register operands */
+#define _ASM_MACRO_3R(OP, R1, R2, R3, ENC)				\
+		".macro	" #OP " " #R1 ", " #R2 ", " #R3 "\n\t"		\
+		_ASM_SET_PARSE_R					\
+		"parse_r __" #R1 ", \\" #R1 "\n\t"			\
+		"parse_r __" #R2 ", \\" #R2 "\n\t"			\
+		"parse_r __" #R3 ", \\" #R3 "\n\t"			\
+		ENC							\
+		_ASM_UNSET_PARSE_R					\
+		".endm\n\t"
+
+/* Instructions with 2 register operands and 1 optional select operand */
+#define _ASM_MACRO_2R_1S(OP, R1, R2, SEL3, ENC)				\
+		".macro	" #OP " " #R1 ", " #R2 ", " #SEL3 " = 0\n\t"	\
+		_ASM_SET_PARSE_R					\
+		"parse_r __" #R1 ", \\" #R1 "\n\t"			\
+		"parse_r __" #R2 ", \\" #R2 "\n\t"			\
+		ENC							\
+		_ASM_UNSET_PARSE_R					\
+		".endm\n\t"
+
+/*
+ * TLB Invalidate Flush
+ */
+static inline void tlbinvf(void)
+{
+	__asm__ __volatile__(
+		".set push\n\t"
+		".set noreorder\n\t"
+		"# tlbinvf\n\t"
+		_ASM_INSN_IF_MIPS(0x42000004)
+		_ASM_INSN32_IF_MM(0x0000537c)
+		".set pop");
+}
+
+
+/*
+ * Functions to access the R10000 performance counters.	 These are basically
+ * mfc0 and mtc0 instructions from and to coprocessor register with a 5-bit
+ * performance counter number encoded into bits 1 ... 5 of the instruction.
+ * Only performance counters 0 to 1 actually exist, so for a non-R10000 aware
+ * disassembler these will look like an access to sel 0 or 1.
+ */
+#define read_r10k_perf_cntr(counter)				\
+({								\
+	unsigned int __res;					\
+	__asm__ __volatile__(					\
+	"mfpc\t%0, %1"						\
+	: "=r" (__res)						\
+	: "i" (counter));					\
+								\
+	__res;							\
+})
+
+#define write_r10k_perf_cntr(counter,val)			\
+do {								\
+	__asm__ __volatile__(					\
+	"mtpc\t%0, %1"						\
+	:							\
+	: "r" (val), "i" (counter));				\
+} while (0)
+
+#define read_r10k_perf_event(counter)				\
+({								\
+	unsigned int __res;					\
+	__asm__ __volatile__(					\
+	"mfps\t%0, %1"						\
+	: "=r" (__res)						\
+	: "i" (counter));					\
+								\
+	__res;							\
+})
+
+#define write_r10k_perf_cntl(counter,val)			\
+do {								\
+	__asm__ __volatile__(					\
+	"mtps\t%0, %1"						\
+	:							\
+	: "r" (val), "i" (counter));				\
+} while (0)
+
+
+/*
+ * Macros to access the system control coprocessor
+ */
+
+#define ___read_32bit_c0_register(source, sel, vol)			\
+({ unsigned int __res;							\
+	if (sel == 0)							\
+		__asm__ vol(						\
+			"mfc0\t%0, " #source "\n\t"			\
+			: "=r" (__res));				\
+	else								\
+		__asm__ vol(						\
+			".set\tpush\n\t"				\
+			".set\tmips32\n\t"				\
+			"mfc0\t%0, " #source ", " #sel "\n\t"		\
+			".set\tpop\n\t"					\
+			: "=r" (__res));				\
+	__res;								\
+})
+
+#define ___read_64bit_c0_register(source, sel, vol)			\
+({ unsigned long long __res;						\
+	if (sizeof(unsigned long) == 4)					\
+		__res = __read_64bit_c0_split(source, sel, vol);	\
+	else if (sel == 0)						\
+		__asm__ vol(						\
+			".set\tpush\n\t"				\
+			".set\tmips3\n\t"				\
+			"dmfc0\t%0, " #source "\n\t"			\
+			".set\tpop"					\
+			: "=r" (__res));				\
+	else								\
+		__asm__ vol(						\
+			".set\tpush\n\t"				\
+			".set\tmips64\n\t"				\
+			"dmfc0\t%0, " #source ", " #sel "\n\t"		\
+			".set\tpop"					\
+			: "=r" (__res));				\
+	__res;								\
+})
+
+#define __read_32bit_c0_register(source, sel)				\
+	___read_32bit_c0_register(source, sel, __volatile__)
+
+#define __read_const_32bit_c0_register(source, sel)			\
+	___read_32bit_c0_register(source, sel,)
+
+#define __read_64bit_c0_register(source, sel)				\
+	___read_64bit_c0_register(source, sel, __volatile__)
+
+#define __read_const_64bit_c0_register(source, sel)			\
+	___read_64bit_c0_register(source, sel,)
+
+#define __write_32bit_c0_register(register, sel, value)			\
+do {									\
+	if (sel == 0)							\
+		__asm__ __volatile__(					\
+			"mtc0\t%z0, " #register "\n\t"			\
+			: : "Jr" ((unsigned int)(value)));		\
+	else								\
+		__asm__ __volatile__(					\
+			".set\tpush\n\t"				\
+			".set\tmips32\n\t"				\
+			"mtc0\t%z0, " #register ", " #sel "\n\t"	\
+			".set\tpop"					\
+			: : "Jr" ((unsigned int)(value)));		\
+} while (0)
+
+#define __write_64bit_c0_register(register, sel, value)			\
+do {									\
+	if (sizeof(unsigned long) == 4)					\
+		__write_64bit_c0_split(register, sel, value);		\
+	else if (sel == 0)						\
+		__asm__ __volatile__(					\
+			".set\tpush\n\t"				\
+			".set\tmips3\n\t"				\
+			"dmtc0\t%z0, " #register "\n\t"			\
+			".set\tpop"					\
+			: : "Jr" (value));				\
+	else								\
+		__asm__ __volatile__(					\
+			".set\tpush\n\t"				\
+			".set\tmips64\n\t"				\
+			"dmtc0\t%z0, " #register ", " #sel "\n\t"	\
+			".set\tpop"					\
+			: : "Jr" (value));				\
+} while (0)
+
+#define __read_ulong_c0_register(reg, sel)				\
+	((sizeof(unsigned long) == 4) ?					\
+	(unsigned long) __read_32bit_c0_register(reg, sel) :		\
+	(unsigned long) __read_64bit_c0_register(reg, sel))
+
+#define __read_const_ulong_c0_register(reg, sel)			\
+	((sizeof(unsigned long) == 4) ?					\
+	(unsigned long) __read_const_32bit_c0_register(reg, sel) :	\
+	(unsigned long) __read_const_64bit_c0_register(reg, sel))
+
+#define __write_ulong_c0_register(reg, sel, val)			\
+do {									\
+	if (sizeof(unsigned long) == 4)					\
+		__write_32bit_c0_register(reg, sel, val);		\
+	else								\
+		__write_64bit_c0_register(reg, sel, val);		\
+} while (0)
+
+/*
+ * On RM7000/RM9000 these are uses to access cop0 set 1 registers
+ */
+#define __read_32bit_c0_ctrl_register(source)				\
+({ unsigned int __res;							\
+	__asm__ __volatile__(						\
+		"cfc0\t%0, " #source "\n\t"				\
+		: "=r" (__res));					\
+	__res;								\
+})
+
+#define __write_32bit_c0_ctrl_register(register, value)			\
+do {									\
+	__asm__ __volatile__(						\
+		"ctc0\t%z0, " #register "\n\t"				\
+		: : "Jr" ((unsigned int)(value)));			\
+} while (0)
+
+/*
+ * These versions are only needed for systems with more than 38 bits of
+ * physical address space running the 32-bit kernel.  That's none atm :-)
+ */
+#define __read_64bit_c0_split(source, sel, vol)				\
+({									\
+	unsigned long long __val;					\
+	unsigned long __flags;						\
+									\
+	local_irq_save(__flags);					\
+	if (sel == 0)							\
+		__asm__ vol(						\
+			".set\tpush\n\t"				\
+			".set\tmips64\n\t"				\
+			"dmfc0\t%L0, " #source "\n\t"			\
+			"dsra\t%M0, %L0, 32\n\t"			\
+			"sll\t%L0, %L0, 0\n\t"				\
+			".set\tpop"					\
+			: "=r" (__val));				\
+	else								\
+		__asm__ vol(						\
+			".set\tpush\n\t"				\
+			".set\tmips64\n\t"				\
+			"dmfc0\t%L0, " #source ", " #sel "\n\t"		\
+			"dsra\t%M0, %L0, 32\n\t"			\
+			"sll\t%L0, %L0, 0\n\t"				\
+			".set\tpop"					\
+			: "=r" (__val));				\
+	local_irq_restore(__flags);					\
+									\
+	__val;								\
+})
+
+#define __write_64bit_c0_split(source, sel, val)			\
+do {									\
+	unsigned long long __tmp = (val);				\
+	unsigned long __flags;						\
+									\
+	local_irq_save(__flags);					\
+	if (MIPS_ISA_REV >= 2)						\
+		__asm__ __volatile__(					\
+			".set\tpush\n\t"				\
+			".set\t" MIPS_ISA_LEVEL "\n\t"			\
+			"dins\t%L0, %M0, 32, 32\n\t"			\
+			"dmtc0\t%L0, " #source ", " #sel "\n\t"		\
+			".set\tpop"					\
+			: "+r" (__tmp));				\
+	else if (sel == 0)						\
+		__asm__ __volatile__(					\
+			".set\tpush\n\t"				\
+			".set\tmips64\n\t"				\
+			"dsll\t%L0, %L0, 32\n\t"			\
+			"dsrl\t%L0, %L0, 32\n\t"			\
+			"dsll\t%M0, %M0, 32\n\t"			\
+			"or\t%L0, %L0, %M0\n\t"				\
+			"dmtc0\t%L0, " #source "\n\t"			\
+			".set\tpop"					\
+			: "+r" (__tmp));				\
+	else								\
+		__asm__ __volatile__(					\
+			".set\tpush\n\t"				\
+			".set\tmips64\n\t"				\
+			"dsll\t%L0, %L0, 32\n\t"			\
+			"dsrl\t%L0, %L0, 32\n\t"			\
+			"dsll\t%M0, %M0, 32\n\t"			\
+			"or\t%L0, %L0, %M0\n\t"				\
+			"dmtc0\t%L0, " #source ", " #sel "\n\t"		\
+			".set\tpop"					\
+			: "+r" (__tmp));				\
+	local_irq_restore(__flags);					\
+} while (0)
+
+#ifndef TOOLCHAIN_SUPPORTS_XPA
+#define _ASM_SET_MFHC0							\
+	_ASM_MACRO_2R_1S(mfhc0, rt, rs, sel,				\
+			 _ASM_INSN_IF_MIPS(0x40400000 | __rt << 16 | __rs << 11 | \\sel)	\
+			 _ASM_INSN32_IF_MM(0x000000f4 | __rt << 21 | __rs << 16 | \\sel << 11))
+#define _ASM_UNSET_MFHC0 ".purgem mfhc0\n\t"
+#define _ASM_SET_MTHC0							\
+	_ASM_MACRO_2R_1S(mthc0, rt, rd, sel,				\
+			 _ASM_INSN_IF_MIPS(0x40c00000 | __rt << 16 | __rd << 11 | \\sel)	\
+			 _ASM_INSN32_IF_MM(0x000002f4 | __rt << 21 | __rd << 16 | \\sel << 11))
+#define _ASM_UNSET_MTHC0 ".purgem mthc0\n\t"
+#else	/* !TOOLCHAIN_SUPPORTS_XPA */
+#define _ASM_SET_MFHC0 ".set\txpa\n\t"
+#define _ASM_SET_MTHC0 ".set\txpa\n\t"
+#define _ASM_UNSET_MFHC0
+#define _ASM_UNSET_MTHC0
+#endif
+
+#define __readx_32bit_c0_register(source, sel)				\
+({									\
+	unsigned int __res;						\
+									\
+	__asm__ __volatile__(						\
+	"	.set	push					\n"	\
+	"	.set	mips32r2				\n"	\
+	_ASM_SET_MFHC0							\
+	"	mfhc0	%0, " #source ", %1			\n"	\
+	_ASM_UNSET_MFHC0						\
+	"	.set	pop					\n"	\
+	: "=r" (__res)							\
+	: "i" (sel));							\
+	__res;								\
+})
+
+#define __writex_32bit_c0_register(register, sel, value)		\
+do {									\
+	__asm__ __volatile__(						\
+	"	.set	push					\n"	\
+	"	.set	mips32r2				\n"	\
+	_ASM_SET_MTHC0							\
+	"	mthc0	%z0, " #register ", %1			\n"	\
+	_ASM_UNSET_MTHC0						\
+	"	.set	pop					\n"	\
+	:								\
+	: "Jr" (value), "i" (sel));					\
+} while (0)
+
+#define read_c0_index()		__read_32bit_c0_register($0, 0)
+#define write_c0_index(val)	__write_32bit_c0_register($0, 0, val)
+
+#define read_c0_random()	__read_32bit_c0_register($1, 0)
+#define write_c0_random(val)	__write_32bit_c0_register($1, 0, val)
+
+#define read_c0_entrylo0()	__read_ulong_c0_register($2, 0)
+#define write_c0_entrylo0(val)	__write_ulong_c0_register($2, 0, val)
+
+#define readx_c0_entrylo0()	__readx_32bit_c0_register($2, 0)
+#define writex_c0_entrylo0(val)	__writex_32bit_c0_register($2, 0, val)
+
+#define read_c0_entrylo1()	__read_ulong_c0_register($3, 0)
+#define write_c0_entrylo1(val)	__write_ulong_c0_register($3, 0, val)
+
+#define readx_c0_entrylo1()	__readx_32bit_c0_register($3, 0)
+#define writex_c0_entrylo1(val)	__writex_32bit_c0_register($3, 0, val)
+
+#define read_c0_conf()		__read_32bit_c0_register($3, 0)
+#define write_c0_conf(val)	__write_32bit_c0_register($3, 0, val)
+
+#define read_c0_globalnumber()	__read_32bit_c0_register($3, 1)
+
+#define read_c0_context()	__read_ulong_c0_register($4, 0)
+#define write_c0_context(val)	__write_ulong_c0_register($4, 0, val)
+
+#define read_c0_contextconfig()		__read_32bit_c0_register($4, 1)
+#define write_c0_contextconfig(val)	__write_32bit_c0_register($4, 1, val)
+
+#define read_c0_userlocal()	__read_ulong_c0_register($4, 2)
+#define write_c0_userlocal(val) __write_ulong_c0_register($4, 2, val)
+
+#define read_c0_xcontextconfig()	__read_ulong_c0_register($4, 3)
+#define write_c0_xcontextconfig(val)	__write_ulong_c0_register($4, 3, val)
+
+#define read_c0_memorymapid()		__read_32bit_c0_register($4, 5)
+#define write_c0_memorymapid(val)	__write_32bit_c0_register($4, 5, val)
+
+#define read_c0_pagemask()	__read_32bit_c0_register($5, 0)
+#define write_c0_pagemask(val)	__write_32bit_c0_register($5, 0, val)
+
+#define read_c0_pagegrain()	__read_32bit_c0_register($5, 1)
+#define write_c0_pagegrain(val) __write_32bit_c0_register($5, 1, val)
+
+#define read_c0_wired()		__read_32bit_c0_register($6, 0)
+#define write_c0_wired(val)	__write_32bit_c0_register($6, 0, val)
+
+#define read_c0_info()		__read_32bit_c0_register($7, 0)
+
+#define read_c0_cache()		__read_32bit_c0_register($7, 0) /* TX39xx */
+#define write_c0_cache(val)	__write_32bit_c0_register($7, 0, val)
+
+#define read_c0_badvaddr()	__read_ulong_c0_register($8, 0)
+#define write_c0_badvaddr(val)	__write_ulong_c0_register($8, 0, val)
+
+#define read_c0_badinstr()	__read_32bit_c0_register($8, 1)
+#define read_c0_badinstrp()	__read_32bit_c0_register($8, 2)
+
+#define read_c0_count()		__read_32bit_c0_register($9, 0)
+#define write_c0_count(val)	__write_32bit_c0_register($9, 0, val)
+
+#define read_c0_entryhi()	__read_ulong_c0_register($10, 0)
+#define write_c0_entryhi(val)	__write_ulong_c0_register($10, 0, val)
+
+#define read_c0_guestctl1()	__read_32bit_c0_register($10, 4)
+#define write_c0_guestctl1(val)	__write_32bit_c0_register($10, 4, val)
+
+#define read_c0_guestctl2()	__read_32bit_c0_register($10, 5)
+#define write_c0_guestctl2(val)	__write_32bit_c0_register($10, 5, val)
+
+#define read_c0_guestctl3()	__read_32bit_c0_register($10, 6)
+#define write_c0_guestctl3(val)	__write_32bit_c0_register($10, 6, val)
+
+#define read_c0_compare()	__read_32bit_c0_register($11, 0)
+#define write_c0_compare(val)	__write_32bit_c0_register($11, 0, val)
+
+#define read_c0_guestctl0ext()	__read_32bit_c0_register($11, 4)
+#define write_c0_guestctl0ext(val) __write_32bit_c0_register($11, 4, val)
+
+#define read_c0_status()	__read_32bit_c0_register($12, 0)
+
+#define write_c0_status(val)	__write_32bit_c0_register($12, 0, val)
+
+#define read_c0_guestctl0()	__read_32bit_c0_register($12, 6)
+#define write_c0_guestctl0(val)	__write_32bit_c0_register($12, 6, val)
+
+#define read_c0_gtoffset()	__read_32bit_c0_register($12, 7)
+#define write_c0_gtoffset(val)	__write_32bit_c0_register($12, 7, val)
+
+#define read_c0_cause()		__read_32bit_c0_register($13, 0)
+#define write_c0_cause(val)	__write_32bit_c0_register($13, 0, val)
+
+#define read_c0_epc()		__read_ulong_c0_register($14, 0)
+#define write_c0_epc(val)	__write_ulong_c0_register($14, 0, val)
+
+#define read_c0_prid()		__read_const_32bit_c0_register($15, 0)
+
+#define read_c0_cmgcrbase()	__read_ulong_c0_register($15, 3)
+
+#define read_c0_config()	__read_32bit_c0_register($16, 0)
+#define read_c0_config1()	__read_32bit_c0_register($16, 1)
+#define read_c0_config2()	__read_32bit_c0_register($16, 2)
+#define read_c0_config3()	__read_32bit_c0_register($16, 3)
+#define read_c0_config4()	__read_32bit_c0_register($16, 4)
+#define read_c0_config5()	__read_32bit_c0_register($16, 5)
+#define read_c0_config6()	__read_32bit_c0_register($16, 6)
+#define read_c0_config7()	__read_32bit_c0_register($16, 7)
+#define write_c0_config(val)	__write_32bit_c0_register($16, 0, val)
+#define write_c0_config1(val)	__write_32bit_c0_register($16, 1, val)
+#define write_c0_config2(val)	__write_32bit_c0_register($16, 2, val)
+#define write_c0_config3(val)	__write_32bit_c0_register($16, 3, val)
+#define write_c0_config4(val)	__write_32bit_c0_register($16, 4, val)
+#define write_c0_config5(val)	__write_32bit_c0_register($16, 5, val)
+#define write_c0_config6(val)	__write_32bit_c0_register($16, 6, val)
+#define write_c0_config7(val)	__write_32bit_c0_register($16, 7, val)
+
+#define read_c0_lladdr()	__read_ulong_c0_register($17, 0)
+#define write_c0_lladdr(val)	__write_ulong_c0_register($17, 0, val)
+#define read_c0_maar()		__read_ulong_c0_register($17, 1)
+#define write_c0_maar(val)	__write_ulong_c0_register($17, 1, val)
+#define readx_c0_maar()		__readx_32bit_c0_register($17, 1)
+#define writex_c0_maar(val)	__writex_32bit_c0_register($17, 1, val)
+#define read_c0_maari()		__read_32bit_c0_register($17, 2)
+#define write_c0_maari(val)	__write_32bit_c0_register($17, 2, val)
+
+/*
+ * The WatchLo register.  There may be up to 8 of them.
+ */
+#define read_c0_watchlo0()	__read_ulong_c0_register($18, 0)
+#define read_c0_watchlo1()	__read_ulong_c0_register($18, 1)
+#define read_c0_watchlo2()	__read_ulong_c0_register($18, 2)
+#define read_c0_watchlo3()	__read_ulong_c0_register($18, 3)
+#define read_c0_watchlo4()	__read_ulong_c0_register($18, 4)
+#define read_c0_watchlo5()	__read_ulong_c0_register($18, 5)
+#define read_c0_watchlo6()	__read_ulong_c0_register($18, 6)
+#define read_c0_watchlo7()	__read_ulong_c0_register($18, 7)
+#define write_c0_watchlo0(val)	__write_ulong_c0_register($18, 0, val)
+#define write_c0_watchlo1(val)	__write_ulong_c0_register($18, 1, val)
+#define write_c0_watchlo2(val)	__write_ulong_c0_register($18, 2, val)
+#define write_c0_watchlo3(val)	__write_ulong_c0_register($18, 3, val)
+#define write_c0_watchlo4(val)	__write_ulong_c0_register($18, 4, val)
+#define write_c0_watchlo5(val)	__write_ulong_c0_register($18, 5, val)
+#define write_c0_watchlo6(val)	__write_ulong_c0_register($18, 6, val)
+#define write_c0_watchlo7(val)	__write_ulong_c0_register($18, 7, val)
+
+/*
+ * The WatchHi register.  There may be up to 8 of them.
+ */
+#define read_c0_watchhi0()	__read_32bit_c0_register($19, 0)
+#define read_c0_watchhi1()	__read_32bit_c0_register($19, 1)
+#define read_c0_watchhi2()	__read_32bit_c0_register($19, 2)
+#define read_c0_watchhi3()	__read_32bit_c0_register($19, 3)
+#define read_c0_watchhi4()	__read_32bit_c0_register($19, 4)
+#define read_c0_watchhi5()	__read_32bit_c0_register($19, 5)
+#define read_c0_watchhi6()	__read_32bit_c0_register($19, 6)
+#define read_c0_watchhi7()	__read_32bit_c0_register($19, 7)
+
+#define write_c0_watchhi0(val)	__write_32bit_c0_register($19, 0, val)
+#define write_c0_watchhi1(val)	__write_32bit_c0_register($19, 1, val)
+#define write_c0_watchhi2(val)	__write_32bit_c0_register($19, 2, val)
+#define write_c0_watchhi3(val)	__write_32bit_c0_register($19, 3, val)
+#define write_c0_watchhi4(val)	__write_32bit_c0_register($19, 4, val)
+#define write_c0_watchhi5(val)	__write_32bit_c0_register($19, 5, val)
+#define write_c0_watchhi6(val)	__write_32bit_c0_register($19, 6, val)
+#define write_c0_watchhi7(val)	__write_32bit_c0_register($19, 7, val)
+
+#define read_c0_xcontext()	__read_ulong_c0_register($20, 0)
+#define write_c0_xcontext(val)	__write_ulong_c0_register($20, 0, val)
+
+#define read_c0_intcontrol()	__read_32bit_c0_ctrl_register($20)
+#define write_c0_intcontrol(val) __write_32bit_c0_ctrl_register($20, val)
+
+#define read_c0_framemask()	__read_32bit_c0_register($21, 0)
+#define write_c0_framemask(val) __write_32bit_c0_register($21, 0, val)
+
+#define read_c0_diag()		__read_32bit_c0_register($22, 0)
+#define write_c0_diag(val)	__write_32bit_c0_register($22, 0, val)
+
+/* R10K CP0 Branch Diagnostic register is 64bits wide */
+#define read_c0_r10k_diag()	__read_64bit_c0_register($22, 0)
+#define write_c0_r10k_diag(val)	__write_64bit_c0_register($22, 0, val)
+
+#define read_c0_diag1()		__read_32bit_c0_register($22, 1)
+#define write_c0_diag1(val)	__write_32bit_c0_register($22, 1, val)
+
+#define read_c0_diag2()		__read_32bit_c0_register($22, 2)
+#define write_c0_diag2(val)	__write_32bit_c0_register($22, 2, val)
+
+#define read_c0_diag3()		__read_32bit_c0_register($22, 3)
+#define write_c0_diag3(val)	__write_32bit_c0_register($22, 3, val)
+
+#define read_c0_diag4()		__read_32bit_c0_register($22, 4)
+#define write_c0_diag4(val)	__write_32bit_c0_register($22, 4, val)
+
+#define read_c0_diag5()		__read_32bit_c0_register($22, 5)
+#define write_c0_diag5(val)	__write_32bit_c0_register($22, 5, val)
+
+#define read_c0_debug()		__read_32bit_c0_register($23, 0)
+#define write_c0_debug(val)	__write_32bit_c0_register($23, 0, val)
+
+#define read_c0_depc()		__read_ulong_c0_register($24, 0)
+#define write_c0_depc(val)	__write_ulong_c0_register($24, 0, val)
+
+/*
+ * MIPS32 / MIPS64 performance counters
+ */
+#define read_c0_perfctrl0()	__read_32bit_c0_register($25, 0)
+#define write_c0_perfctrl0(val) __write_32bit_c0_register($25, 0, val)
+#define read_c0_perfcntr0()	__read_32bit_c0_register($25, 1)
+#define write_c0_perfcntr0(val) __write_32bit_c0_register($25, 1, val)
+#define read_c0_perfcntr0_64()	__read_64bit_c0_register($25, 1)
+#define write_c0_perfcntr0_64(val) __write_64bit_c0_register($25, 1, val)
+#define read_c0_perfctrl1()	__read_32bit_c0_register($25, 2)
+#define write_c0_perfctrl1(val) __write_32bit_c0_register($25, 2, val)
+#define read_c0_perfcntr1()	__read_32bit_c0_register($25, 3)
+#define write_c0_perfcntr1(val) __write_32bit_c0_register($25, 3, val)
+#define read_c0_perfcntr1_64()	__read_64bit_c0_register($25, 3)
+#define write_c0_perfcntr1_64(val) __write_64bit_c0_register($25, 3, val)
+#define read_c0_perfctrl2()	__read_32bit_c0_register($25, 4)
+#define write_c0_perfctrl2(val) __write_32bit_c0_register($25, 4, val)
+#define read_c0_perfcntr2()	__read_32bit_c0_register($25, 5)
+#define write_c0_perfcntr2(val) __write_32bit_c0_register($25, 5, val)
+#define read_c0_perfcntr2_64()	__read_64bit_c0_register($25, 5)
+#define write_c0_perfcntr2_64(val) __write_64bit_c0_register($25, 5, val)
+#define read_c0_perfctrl3()	__read_32bit_c0_register($25, 6)
+#define write_c0_perfctrl3(val) __write_32bit_c0_register($25, 6, val)
+#define read_c0_perfcntr3()	__read_32bit_c0_register($25, 7)
+#define write_c0_perfcntr3(val) __write_32bit_c0_register($25, 7, val)
+#define read_c0_perfcntr3_64()	__read_64bit_c0_register($25, 7)
+#define write_c0_perfcntr3_64(val) __write_64bit_c0_register($25, 7, val)
+
+#define read_c0_ecc()		__read_32bit_c0_register($26, 0)
+#define write_c0_ecc(val)	__write_32bit_c0_register($26, 0, val)
+
+#define read_c0_derraddr0()	__read_ulong_c0_register($26, 1)
+#define write_c0_derraddr0(val) __write_ulong_c0_register($26, 1, val)
+
+#define read_c0_cacheerr()	__read_32bit_c0_register($27, 0)
+
+#define read_c0_derraddr1()	__read_ulong_c0_register($27, 1)
+#define write_c0_derraddr1(val) __write_ulong_c0_register($27, 1, val)
+
+#define read_c0_taglo()		__read_32bit_c0_register($28, 0)
+#define write_c0_taglo(val)	__write_32bit_c0_register($28, 0, val)
+
+#define read_c0_dtaglo()	__read_32bit_c0_register($28, 2)
+#define write_c0_dtaglo(val)	__write_32bit_c0_register($28, 2, val)
+
+#define read_c0_ddatalo()	__read_32bit_c0_register($28, 3)
+#define write_c0_ddatalo(val)	__write_32bit_c0_register($28, 3, val)
+
+#define read_c0_staglo()	__read_32bit_c0_register($28, 4)
+#define write_c0_staglo(val)	__write_32bit_c0_register($28, 4, val)
+
+#define read_c0_taghi()		__read_32bit_c0_register($29, 0)
+#define write_c0_taghi(val)	__write_32bit_c0_register($29, 0, val)
+
+#define read_c0_errorepc()	__read_ulong_c0_register($30, 0)
+#define write_c0_errorepc(val)	__write_ulong_c0_register($30, 0, val)
+
+/* MIPSR2 */
+#define read_c0_hwrena()	__read_32bit_c0_register($7, 0)
+#define write_c0_hwrena(val)	__write_32bit_c0_register($7, 0, val)
+
+#define read_c0_intctl()	__read_32bit_c0_register($12, 1)
+#define write_c0_intctl(val)	__write_32bit_c0_register($12, 1, val)
+
+#define read_c0_srsctl()	__read_32bit_c0_register($12, 2)
+#define write_c0_srsctl(val)	__write_32bit_c0_register($12, 2, val)
+
+#define read_c0_srsmap()	__read_32bit_c0_register($12, 3)
+#define write_c0_srsmap(val)	__write_32bit_c0_register($12, 3, val)
+
+#define read_c0_ebase()		__read_32bit_c0_register($15, 1)
+#define write_c0_ebase(val)	__write_32bit_c0_register($15, 1, val)
+
+#define read_c0_ebase_64()	__read_64bit_c0_register($15, 1)
+#define write_c0_ebase_64(val)	__write_64bit_c0_register($15, 1, val)
+
+#define read_c0_cdmmbase()	__read_ulong_c0_register($15, 2)
+#define write_c0_cdmmbase(val)	__write_ulong_c0_register($15, 2, val)
+
+/* MIPSR3 */
+#define read_c0_segctl0()	__read_32bit_c0_register($5, 2)
+#define write_c0_segctl0(val)	__write_32bit_c0_register($5, 2, val)
+
+#define read_c0_segctl1()	__read_32bit_c0_register($5, 3)
+#define write_c0_segctl1(val)	__write_32bit_c0_register($5, 3, val)
+
+#define read_c0_segctl2()	__read_32bit_c0_register($5, 4)
+#define write_c0_segctl2(val)	__write_32bit_c0_register($5, 4, val)
+
+/* Hardware Page Table Walker */
+#define read_c0_pwbase()	__read_ulong_c0_register($5, 5)
+#define write_c0_pwbase(val)	__write_ulong_c0_register($5, 5, val)
+
+#define read_c0_pwfield()	__read_ulong_c0_register($5, 6)
+#define write_c0_pwfield(val)	__write_ulong_c0_register($5, 6, val)
+
+#define read_c0_pwsize()	__read_ulong_c0_register($5, 7)
+#define write_c0_pwsize(val)	__write_ulong_c0_register($5, 7, val)
+
+#define read_c0_pwctl()		__read_32bit_c0_register($6, 6)
+#define write_c0_pwctl(val)	__write_32bit_c0_register($6, 6, val)
+
+#define read_c0_pgd()		__read_64bit_c0_register($9, 7)
+#define write_c0_pgd(val)	__write_64bit_c0_register($9, 7, val)
+
+#define read_c0_kpgd()		__read_64bit_c0_register($31, 7)
+#define write_c0_kpgd(val)	__write_64bit_c0_register($31, 7, val)
+
+/* Cavium OCTEON (cnMIPS) */
+#define read_c0_cvmcount()	__read_ulong_c0_register($9, 6)
+#define write_c0_cvmcount(val)	__write_ulong_c0_register($9, 6, val)
+
+#define read_c0_cvmctl()	__read_64bit_c0_register($9, 7)
+#define write_c0_cvmctl(val)	__write_64bit_c0_register($9, 7, val)
+
+#define read_c0_cvmmemctl()	__read_64bit_c0_register($11, 7)
+#define write_c0_cvmmemctl(val) __write_64bit_c0_register($11, 7, val)
+
+#define read_c0_cvmmemctl2()	__read_64bit_c0_register($16, 6)
+#define write_c0_cvmmemctl2(val) __write_64bit_c0_register($16, 6, val)
+
+#define read_c0_cvmvmconfig()	__read_64bit_c0_register($16, 7)
+#define write_c0_cvmvmconfig(val) __write_64bit_c0_register($16, 7, val)
+
+/*
+ * The cacheerr registers are not standardized.	 On OCTEON, they are
+ * 64 bits wide.
+ */
+#define read_octeon_c0_icacheerr()	__read_64bit_c0_register($27, 0)
+#define write_octeon_c0_icacheerr(val)	__write_64bit_c0_register($27, 0, val)
+
+#define read_octeon_c0_dcacheerr()	__read_64bit_c0_register($27, 1)
+#define write_octeon_c0_dcacheerr(val)	__write_64bit_c0_register($27, 1, val)
+
+/* BMIPS3300 */
+#define read_c0_brcm_config_0()		__read_32bit_c0_register($22, 0)
+#define write_c0_brcm_config_0(val)	__write_32bit_c0_register($22, 0, val)
+
+#define read_c0_brcm_bus_pll()		__read_32bit_c0_register($22, 4)
+#define write_c0_brcm_bus_pll(val)	__write_32bit_c0_register($22, 4, val)
+
+#define read_c0_brcm_reset()		__read_32bit_c0_register($22, 5)
+#define write_c0_brcm_reset(val)	__write_32bit_c0_register($22, 5, val)
+
+/* BMIPS43xx */
+#define read_c0_brcm_cmt_intr()		__read_32bit_c0_register($22, 1)
+#define write_c0_brcm_cmt_intr(val)	__write_32bit_c0_register($22, 1, val)
+
+#define read_c0_brcm_cmt_ctrl()		__read_32bit_c0_register($22, 2)
+#define write_c0_brcm_cmt_ctrl(val)	__write_32bit_c0_register($22, 2, val)
+
+#define read_c0_brcm_cmt_local()	__read_32bit_c0_register($22, 3)
+#define write_c0_brcm_cmt_local(val)	__write_32bit_c0_register($22, 3, val)
+
+#define read_c0_brcm_config_1()		__read_32bit_c0_register($22, 5)
+#define write_c0_brcm_config_1(val)	__write_32bit_c0_register($22, 5, val)
+
+#define read_c0_brcm_cbr()		__read_32bit_c0_register($22, 6)
+#define write_c0_brcm_cbr(val)		__write_32bit_c0_register($22, 6, val)
+
+/* BMIPS5000 */
+#define read_c0_brcm_config()		__read_32bit_c0_register($22, 0)
+#define write_c0_brcm_config(val)	__write_32bit_c0_register($22, 0, val)
+
+#define read_c0_brcm_mode()		__read_32bit_c0_register($22, 1)
+#define write_c0_brcm_mode(val)		__write_32bit_c0_register($22, 1, val)
+
+#define read_c0_brcm_action()		__read_32bit_c0_register($22, 2)
+#define write_c0_brcm_action(val)	__write_32bit_c0_register($22, 2, val)
+
+#define read_c0_brcm_edsp()		__read_32bit_c0_register($22, 3)
+#define write_c0_brcm_edsp(val)		__write_32bit_c0_register($22, 3, val)
+
+#define read_c0_brcm_bootvec()		__read_32bit_c0_register($22, 4)
+#define write_c0_brcm_bootvec(val)	__write_32bit_c0_register($22, 4, val)
+
+#define read_c0_brcm_sleepcount()	__read_32bit_c0_register($22, 7)
+#define write_c0_brcm_sleepcount(val)	__write_32bit_c0_register($22, 7, val)
+
+/* Ingenic page ctrl register */
+#define write_c0_page_ctrl(val)	__write_32bit_c0_register($5, 4, val)
+
+/*
+ * Macros to access the guest system control coprocessor
+ */
+
+#ifndef TOOLCHAIN_SUPPORTS_VIRT
+#define _ASM_SET_MFGC0							\
+	_ASM_MACRO_2R_1S(mfgc0, rt, rs, sel,				\
+			 _ASM_INSN_IF_MIPS(0x40600000 | __rt << 16 | __rs << 11 | \\sel)	\
+			 _ASM_INSN32_IF_MM(0x000004fc | __rt << 21 | __rs << 16 | \\sel << 11))
+#define _ASM_UNSET_MFGC0 ".purgem mfgc0\n\t"
+#define _ASM_SET_DMFGC0							\
+	_ASM_MACRO_2R_1S(dmfgc0, rt, rs, sel,				\
+			 _ASM_INSN_IF_MIPS(0x40600100 | __rt << 16 | __rs << 11 | \\sel)	\
+			 _ASM_INSN32_IF_MM(0x580004fc | __rt << 21 | __rs << 16 | \\sel << 11))
+#define _ASM_UNSET_DMFGC0 ".purgem dmfgc0\n\t"
+#define _ASM_SET_MTGC0							\
+	_ASM_MACRO_2R_1S(mtgc0, rt, rd, sel,				\
+			 _ASM_INSN_IF_MIPS(0x40600200 | __rt << 16 | __rd << 11 | \\sel)	\
+			 _ASM_INSN32_IF_MM(0x000006fc | __rt << 21 | __rd << 16 | \\sel << 11))
+#define _ASM_UNSET_MTGC0 ".purgem mtgc0\n\t"
+#define _ASM_SET_DMTGC0							\
+	_ASM_MACRO_2R_1S(dmtgc0, rt, rd, sel,				\
+			 _ASM_INSN_IF_MIPS(0x40600300 | __rt << 16 | __rd << 11 | \\sel)	\
+			 _ASM_INSN32_IF_MM(0x580006fc | __rt << 21 | __rd << 16 | \\sel << 11))
+#define _ASM_UNSET_DMTGC0 ".purgem dmtgc0\n\t"
+
+#define __tlbgp()							\
+		_ASM_INSN_IF_MIPS(0x42000010)				\
+		_ASM_INSN32_IF_MM(0x0000017c)
+#define __tlbgr()							\
+		_ASM_INSN_IF_MIPS(0x42000009)				\
+		_ASM_INSN32_IF_MM(0x0000117c)
+#define __tlbgwi()							\
+		_ASM_INSN_IF_MIPS(0x4200000a)				\
+		_ASM_INSN32_IF_MM(0x0000217c)
+#define __tlbgwr()							\
+		_ASM_INSN_IF_MIPS(0x4200000e)				\
+		_ASM_INSN32_IF_MM(0x0000317c)
+#define __tlbginvf()							\
+		_ASM_INSN_IF_MIPS(0x4200000c)				\
+		_ASM_INSN32_IF_MM(0x0000517c)
+#else	/* !TOOLCHAIN_SUPPORTS_VIRT */
+#define _ASM_SET_VIRT ".set\tvirt\n\t"
+#define _ASM_SET_MFGC0	_ASM_SET_VIRT
+#define _ASM_SET_DMFGC0	_ASM_SET_VIRT
+#define _ASM_SET_MTGC0	_ASM_SET_VIRT
+#define _ASM_SET_DMTGC0	_ASM_SET_VIRT
+#define _ASM_UNSET_MFGC0
+#define _ASM_UNSET_DMFGC0
+#define _ASM_UNSET_MTGC0
+#define _ASM_UNSET_DMTGC0
+
+#define __tlbgp()	_ASM_SET_VIRT "tlbgp\n\t"
+#define __tlbgr()	_ASM_SET_VIRT "tlbgr\n\t"
+#define __tlbgwi()	_ASM_SET_VIRT "tlbgwi\n\t"
+#define __tlbgwr()	_ASM_SET_VIRT "tlbgwr\n\t"
+#define __tlbginvf()	_ASM_SET_VIRT "tlbginvf\n\t"
+#endif
+
+#define __read_32bit_gc0_register(source, sel)				\
+({ int __res;								\
+	__asm__ __volatile__(						\
+		".set\tpush\n\t"					\
+		".set\tmips32r5\n\t"					\
+		_ASM_SET_MFGC0						\
+		"mfgc0\t%0, " #source ", %1\n\t"			\
+		_ASM_UNSET_MFGC0					\
+		".set\tpop"						\
+		: "=r" (__res)						\
+		: "i" (sel));						\
+	__res;								\
+})
+
+#define __read_64bit_gc0_register(source, sel)				\
+({ unsigned long long __res;						\
+	__asm__ __volatile__(						\
+		".set\tpush\n\t"					\
+		".set\tmips64r5\n\t"					\
+		_ASM_SET_DMFGC0						\
+		"dmfgc0\t%0, " #source ", %1\n\t"			\
+		_ASM_UNSET_DMFGC0					\
+		".set\tpop"						\
+		: "=r" (__res)						\
+		: "i" (sel));						\
+	__res;								\
+})
+
+#define __write_32bit_gc0_register(register, sel, value)		\
+do {									\
+	__asm__ __volatile__(						\
+		".set\tpush\n\t"					\
+		".set\tmips32r5\n\t"					\
+		_ASM_SET_MTGC0						\
+		"mtgc0\t%z0, " #register ", %1\n\t"			\
+		_ASM_UNSET_MTGC0					\
+		".set\tpop"						\
+		: : "Jr" ((unsigned int)(value)),			\
+		    "i" (sel));						\
+} while (0)
+
+#define __write_64bit_gc0_register(register, sel, value)		\
+do {									\
+	__asm__ __volatile__(						\
+		".set\tpush\n\t"					\
+		".set\tmips64r5\n\t"					\
+		_ASM_SET_DMTGC0						\
+		"dmtgc0\t%z0, " #register ", %1\n\t"			\
+		_ASM_UNSET_DMTGC0					\
+		".set\tpop"						\
+		: : "Jr" (value),					\
+		    "i" (sel));						\
+} while (0)
+
+#define __read_ulong_gc0_register(reg, sel)				\
+	((sizeof(unsigned long) == 4) ?					\
+	(unsigned long) __read_32bit_gc0_register(reg, sel) :		\
+	(unsigned long) __read_64bit_gc0_register(reg, sel))
+
+#define __write_ulong_gc0_register(reg, sel, val)			\
+do {									\
+	if (sizeof(unsigned long) == 4)					\
+		__write_32bit_gc0_register(reg, sel, val);		\
+	else								\
+		__write_64bit_gc0_register(reg, sel, val);		\
+} while (0)
+
+#define read_gc0_index()		__read_32bit_gc0_register($0, 0)
+#define write_gc0_index(val)		__write_32bit_gc0_register($0, 0, val)
+
+#define read_gc0_entrylo0()		__read_ulong_gc0_register($2, 0)
+#define write_gc0_entrylo0(val)		__write_ulong_gc0_register($2, 0, val)
+
+#define read_gc0_entrylo1()		__read_ulong_gc0_register($3, 0)
+#define write_gc0_entrylo1(val)		__write_ulong_gc0_register($3, 0, val)
+
+#define read_gc0_context()		__read_ulong_gc0_register($4, 0)
+#define write_gc0_context(val)		__write_ulong_gc0_register($4, 0, val)
+
+#define read_gc0_contextconfig()	__read_32bit_gc0_register($4, 1)
+#define write_gc0_contextconfig(val)	__write_32bit_gc0_register($4, 1, val)
+
+#define read_gc0_userlocal()		__read_ulong_gc0_register($4, 2)
+#define write_gc0_userlocal(val)	__write_ulong_gc0_register($4, 2, val)
+
+#define read_gc0_xcontextconfig()	__read_ulong_gc0_register($4, 3)
+#define write_gc0_xcontextconfig(val)	__write_ulong_gc0_register($4, 3, val)
+
+#define read_gc0_pagemask()		__read_32bit_gc0_register($5, 0)
+#define write_gc0_pagemask(val)		__write_32bit_gc0_register($5, 0, val)
+
+#define read_gc0_pagegrain()		__read_32bit_gc0_register($5, 1)
+#define write_gc0_pagegrain(val)	__write_32bit_gc0_register($5, 1, val)
+
+#define read_gc0_segctl0()		__read_ulong_gc0_register($5, 2)
+#define write_gc0_segctl0(val)		__write_ulong_gc0_register($5, 2, val)
+
+#define read_gc0_segctl1()		__read_ulong_gc0_register($5, 3)
+#define write_gc0_segctl1(val)		__write_ulong_gc0_register($5, 3, val)
+
+#define read_gc0_segctl2()		__read_ulong_gc0_register($5, 4)
+#define write_gc0_segctl2(val)		__write_ulong_gc0_register($5, 4, val)
+
+#define read_gc0_pwbase()		__read_ulong_gc0_register($5, 5)
+#define write_gc0_pwbase(val)		__write_ulong_gc0_register($5, 5, val)
+
+#define read_gc0_pwfield()		__read_ulong_gc0_register($5, 6)
+#define write_gc0_pwfield(val)		__write_ulong_gc0_register($5, 6, val)
+
+#define read_gc0_pwsize()		__read_ulong_gc0_register($5, 7)
+#define write_gc0_pwsize(val)		__write_ulong_gc0_register($5, 7, val)
+
+#define read_gc0_wired()		__read_32bit_gc0_register($6, 0)
+#define write_gc0_wired(val)		__write_32bit_gc0_register($6, 0, val)
+
+#define read_gc0_pwctl()		__read_32bit_gc0_register($6, 6)
+#define write_gc0_pwctl(val)		__write_32bit_gc0_register($6, 6, val)
+
+#define read_gc0_hwrena()		__read_32bit_gc0_register($7, 0)
+#define write_gc0_hwrena(val)		__write_32bit_gc0_register($7, 0, val)
+
+#define read_gc0_badvaddr()		__read_ulong_gc0_register($8, 0)
+#define write_gc0_badvaddr(val)		__write_ulong_gc0_register($8, 0, val)
+
+#define read_gc0_badinstr()		__read_32bit_gc0_register($8, 1)
+#define write_gc0_badinstr(val)		__write_32bit_gc0_register($8, 1, val)
+
+#define read_gc0_badinstrp()		__read_32bit_gc0_register($8, 2)
+#define write_gc0_badinstrp(val)	__write_32bit_gc0_register($8, 2, val)
+
+#define read_gc0_count()		__read_32bit_gc0_register($9, 0)
+
+#define read_gc0_entryhi()		__read_ulong_gc0_register($10, 0)
+#define write_gc0_entryhi(val)		__write_ulong_gc0_register($10, 0, val)
+
+#define read_gc0_compare()		__read_32bit_gc0_register($11, 0)
+#define write_gc0_compare(val)		__write_32bit_gc0_register($11, 0, val)
+
+#define read_gc0_status()		__read_32bit_gc0_register($12, 0)
+#define write_gc0_status(val)		__write_32bit_gc0_register($12, 0, val)
+
+#define read_gc0_intctl()		__read_32bit_gc0_register($12, 1)
+#define write_gc0_intctl(val)		__write_32bit_gc0_register($12, 1, val)
+
+#define read_gc0_cause()		__read_32bit_gc0_register($13, 0)
+#define write_gc0_cause(val)		__write_32bit_gc0_register($13, 0, val)
+
+#define read_gc0_epc()			__read_ulong_gc0_register($14, 0)
+#define write_gc0_epc(val)		__write_ulong_gc0_register($14, 0, val)
+
+#define read_gc0_prid()			__read_32bit_gc0_register($15, 0)
+
+#define read_gc0_ebase()		__read_32bit_gc0_register($15, 1)
+#define write_gc0_ebase(val)		__write_32bit_gc0_register($15, 1, val)
+
+#define read_gc0_ebase_64()		__read_64bit_gc0_register($15, 1)
+#define write_gc0_ebase_64(val)		__write_64bit_gc0_register($15, 1, val)
+
+#define read_gc0_config()		__read_32bit_gc0_register($16, 0)
+#define read_gc0_config1()		__read_32bit_gc0_register($16, 1)
+#define read_gc0_config2()		__read_32bit_gc0_register($16, 2)
+#define read_gc0_config3()		__read_32bit_gc0_register($16, 3)
+#define read_gc0_config4()		__read_32bit_gc0_register($16, 4)
+#define read_gc0_config5()		__read_32bit_gc0_register($16, 5)
+#define read_gc0_config6()		__read_32bit_gc0_register($16, 6)
+#define read_gc0_config7()		__read_32bit_gc0_register($16, 7)
+#define write_gc0_config(val)		__write_32bit_gc0_register($16, 0, val)
+#define write_gc0_config1(val)		__write_32bit_gc0_register($16, 1, val)
+#define write_gc0_config2(val)		__write_32bit_gc0_register($16, 2, val)
+#define write_gc0_config3(val)		__write_32bit_gc0_register($16, 3, val)
+#define write_gc0_config4(val)		__write_32bit_gc0_register($16, 4, val)
+#define write_gc0_config5(val)		__write_32bit_gc0_register($16, 5, val)
+#define write_gc0_config6(val)		__write_32bit_gc0_register($16, 6, val)
+#define write_gc0_config7(val)		__write_32bit_gc0_register($16, 7, val)
+
+#define read_gc0_lladdr()		__read_ulong_gc0_register($17, 0)
+#define write_gc0_lladdr(val)		__write_ulong_gc0_register($17, 0, val)
+
+#define read_gc0_watchlo0()		__read_ulong_gc0_register($18, 0)
+#define read_gc0_watchlo1()		__read_ulong_gc0_register($18, 1)
+#define read_gc0_watchlo2()		__read_ulong_gc0_register($18, 2)
+#define read_gc0_watchlo3()		__read_ulong_gc0_register($18, 3)
+#define read_gc0_watchlo4()		__read_ulong_gc0_register($18, 4)
+#define read_gc0_watchlo5()		__read_ulong_gc0_register($18, 5)
+#define read_gc0_watchlo6()		__read_ulong_gc0_register($18, 6)
+#define read_gc0_watchlo7()		__read_ulong_gc0_register($18, 7)
+#define write_gc0_watchlo0(val)		__write_ulong_gc0_register($18, 0, val)
+#define write_gc0_watchlo1(val)		__write_ulong_gc0_register($18, 1, val)
+#define write_gc0_watchlo2(val)		__write_ulong_gc0_register($18, 2, val)
+#define write_gc0_watchlo3(val)		__write_ulong_gc0_register($18, 3, val)
+#define write_gc0_watchlo4(val)		__write_ulong_gc0_register($18, 4, val)
+#define write_gc0_watchlo5(val)		__write_ulong_gc0_register($18, 5, val)
+#define write_gc0_watchlo6(val)		__write_ulong_gc0_register($18, 6, val)
+#define write_gc0_watchlo7(val)		__write_ulong_gc0_register($18, 7, val)
+
+#define read_gc0_watchhi0()		__read_32bit_gc0_register($19, 0)
+#define read_gc0_watchhi1()		__read_32bit_gc0_register($19, 1)
+#define read_gc0_watchhi2()		__read_32bit_gc0_register($19, 2)
+#define read_gc0_watchhi3()		__read_32bit_gc0_register($19, 3)
+#define read_gc0_watchhi4()		__read_32bit_gc0_register($19, 4)
+#define read_gc0_watchhi5()		__read_32bit_gc0_register($19, 5)
+#define read_gc0_watchhi6()		__read_32bit_gc0_register($19, 6)
+#define read_gc0_watchhi7()		__read_32bit_gc0_register($19, 7)
+#define write_gc0_watchhi0(val)		__write_32bit_gc0_register($19, 0, val)
+#define write_gc0_watchhi1(val)		__write_32bit_gc0_register($19, 1, val)
+#define write_gc0_watchhi2(val)		__write_32bit_gc0_register($19, 2, val)
+#define write_gc0_watchhi3(val)		__write_32bit_gc0_register($19, 3, val)
+#define write_gc0_watchhi4(val)		__write_32bit_gc0_register($19, 4, val)
+#define write_gc0_watchhi5(val)		__write_32bit_gc0_register($19, 5, val)
+#define write_gc0_watchhi6(val)		__write_32bit_gc0_register($19, 6, val)
+#define write_gc0_watchhi7(val)		__write_32bit_gc0_register($19, 7, val)
+
+#define read_gc0_xcontext()		__read_ulong_gc0_register($20, 0)
+#define write_gc0_xcontext(val)		__write_ulong_gc0_register($20, 0, val)
+
+#define read_gc0_perfctrl0()		__read_32bit_gc0_register($25, 0)
+#define write_gc0_perfctrl0(val)	__write_32bit_gc0_register($25, 0, val)
+#define read_gc0_perfcntr0()		__read_32bit_gc0_register($25, 1)
+#define write_gc0_perfcntr0(val)	__write_32bit_gc0_register($25, 1, val)
+#define read_gc0_perfcntr0_64()		__read_64bit_gc0_register($25, 1)
+#define write_gc0_perfcntr0_64(val)	__write_64bit_gc0_register($25, 1, val)
+#define read_gc0_perfctrl1()		__read_32bit_gc0_register($25, 2)
+#define write_gc0_perfctrl1(val)	__write_32bit_gc0_register($25, 2, val)
+#define read_gc0_perfcntr1()		__read_32bit_gc0_register($25, 3)
+#define write_gc0_perfcntr1(val)	__write_32bit_gc0_register($25, 3, val)
+#define read_gc0_perfcntr1_64()		__read_64bit_gc0_register($25, 3)
+#define write_gc0_perfcntr1_64(val)	__write_64bit_gc0_register($25, 3, val)
+#define read_gc0_perfctrl2()		__read_32bit_gc0_register($25, 4)
+#define write_gc0_perfctrl2(val)	__write_32bit_gc0_register($25, 4, val)
+#define read_gc0_perfcntr2()		__read_32bit_gc0_register($25, 5)
+#define write_gc0_perfcntr2(val)	__write_32bit_gc0_register($25, 5, val)
+#define read_gc0_perfcntr2_64()		__read_64bit_gc0_register($25, 5)
+#define write_gc0_perfcntr2_64(val)	__write_64bit_gc0_register($25, 5, val)
+#define read_gc0_perfctrl3()		__read_32bit_gc0_register($25, 6)
+#define write_gc0_perfctrl3(val)	__write_32bit_gc0_register($25, 6, val)
+#define read_gc0_perfcntr3()		__read_32bit_gc0_register($25, 7)
+#define write_gc0_perfcntr3(val)	__write_32bit_gc0_register($25, 7, val)
+#define read_gc0_perfcntr3_64()		__read_64bit_gc0_register($25, 7)
+#define write_gc0_perfcntr3_64(val)	__write_64bit_gc0_register($25, 7, val)
+
+#define read_gc0_errorepc()		__read_ulong_gc0_register($30, 0)
+#define write_gc0_errorepc(val)		__write_ulong_gc0_register($30, 0, val)
+
+#define read_gc0_kscratch1()		__read_ulong_gc0_register($31, 2)
+#define read_gc0_kscratch2()		__read_ulong_gc0_register($31, 3)
+#define read_gc0_kscratch3()		__read_ulong_gc0_register($31, 4)
+#define read_gc0_kscratch4()		__read_ulong_gc0_register($31, 5)
+#define read_gc0_kscratch5()		__read_ulong_gc0_register($31, 6)
+#define read_gc0_kscratch6()		__read_ulong_gc0_register($31, 7)
+#define write_gc0_kscratch1(val)	__write_ulong_gc0_register($31, 2, val)
+#define write_gc0_kscratch2(val)	__write_ulong_gc0_register($31, 3, val)
+#define write_gc0_kscratch3(val)	__write_ulong_gc0_register($31, 4, val)
+#define write_gc0_kscratch4(val)	__write_ulong_gc0_register($31, 5, val)
+#define write_gc0_kscratch5(val)	__write_ulong_gc0_register($31, 6, val)
+#define write_gc0_kscratch6(val)	__write_ulong_gc0_register($31, 7, val)
+
+/* Cavium OCTEON (cnMIPS) */
+#define read_gc0_cvmcount()		__read_ulong_gc0_register($9, 6)
+#define write_gc0_cvmcount(val)		__write_ulong_gc0_register($9, 6, val)
+
+#define read_gc0_cvmctl()		__read_64bit_gc0_register($9, 7)
+#define write_gc0_cvmctl(val)		__write_64bit_gc0_register($9, 7, val)
+
+#define read_gc0_cvmmemctl()		__read_64bit_gc0_register($11, 7)
+#define write_gc0_cvmmemctl(val)	__write_64bit_gc0_register($11, 7, val)
+
+#define read_gc0_cvmmemctl2()		__read_64bit_gc0_register($16, 6)
+#define write_gc0_cvmmemctl2(val)	__write_64bit_gc0_register($16, 6, val)
+
+/*
+ * Macros to access the floating point coprocessor control registers
+ */
+#define _read_32bit_cp1_register(source, gas_hardfloat)			\
+({									\
+	unsigned int __res;						\
+									\
+	__asm__ __volatile__(						\
+	"	.set	push					\n"	\
+	"	.set	reorder					\n"	\
+	"	# gas fails to assemble cfc1 for some archs,	\n"	\
+	"	# like Octeon.					\n"	\
+	"	.set	mips1					\n"	\
+	"	"STR(gas_hardfloat)"				\n"	\
+	"	cfc1	%0,"STR(source)"			\n"	\
+	"	.set	pop					\n"	\
+	: "=r" (__res));						\
+	__res;								\
+})
+
+#define _write_32bit_cp1_register(dest, val, gas_hardfloat)		\
+do {									\
+	__asm__ __volatile__(						\
+	"	.set	push					\n"	\
+	"	.set	reorder					\n"	\
+	"	"STR(gas_hardfloat)"				\n"	\
+	"	ctc1	%0,"STR(dest)"				\n"	\
+	"	.set	pop					\n"	\
+	: : "r" (val));							\
+} while (0)
+
+#ifdef GAS_HAS_SET_HARDFLOAT
+#define read_32bit_cp1_register(source)					\
+	_read_32bit_cp1_register(source, .set hardfloat)
+#define write_32bit_cp1_register(dest, val)				\
+	_write_32bit_cp1_register(dest, val, .set hardfloat)
+#else
+#define read_32bit_cp1_register(source)					\
+	_read_32bit_cp1_register(source, )
+#define write_32bit_cp1_register(dest, val)				\
+	_write_32bit_cp1_register(dest, val, )
+#endif
+
+#ifdef TOOLCHAIN_SUPPORTS_DSP
+#define rddsp(mask)							\
+({									\
+	unsigned int __dspctl;						\
+									\
+	__asm__ __volatile__(						\
+	"	.set push					\n"	\
+	"	.set " MIPS_ISA_LEVEL "				\n"	\
+	"	.set dsp					\n"	\
+	"	rddsp	%0, %x1					\n"	\
+	"	.set pop					\n"	\
+	: "=r" (__dspctl)						\
+	: "i" (mask));							\
+	__dspctl;							\
+})
+
+#define wrdsp(val, mask)						\
+do {									\
+	__asm__ __volatile__(						\
+	"	.set push					\n"	\
+	"	.set " MIPS_ISA_LEVEL "				\n"	\
+	"	.set dsp					\n"	\
+	"	wrdsp	%0, %x1					\n"	\
+	"	.set pop					\n"	\
+	:								\
+	: "r" (val), "i" (mask));					\
+} while (0)
+
+#define mflo0()								\
+({									\
+	long mflo0;							\
+	__asm__(							\
+	"	.set push					\n"	\
+	"	.set " MIPS_ISA_LEVEL "				\n"	\
+	"	.set dsp					\n"	\
+	"	mflo %0, $ac0					\n"	\
+	"	.set pop					\n" 	\
+	: "=r" (mflo0)); 						\
+	mflo0;								\
+})
+
+#define mflo1()								\
+({									\
+	long mflo1;							\
+	__asm__(							\
+	"	.set push					\n"	\
+	"	.set " MIPS_ISA_LEVEL "				\n"	\
+	"	.set dsp					\n"	\
+	"	mflo %0, $ac1					\n"	\
+	"	.set pop					\n" 	\
+	: "=r" (mflo1)); 						\
+	mflo1;								\
+})
+
+#define mflo2()								\
+({									\
+	long mflo2;							\
+	__asm__(							\
+	"	.set push					\n"	\
+	"	.set " MIPS_ISA_LEVEL "				\n"	\
+	"	.set dsp					\n"	\
+	"	mflo %0, $ac2					\n"	\
+	"	.set pop					\n" 	\
+	: "=r" (mflo2)); 						\
+	mflo2;								\
+})
+
+#define mflo3()								\
+({									\
+	long mflo3;							\
+	__asm__(							\
+	"	.set push					\n"	\
+	"	.set " MIPS_ISA_LEVEL "				\n"	\
+	"	.set dsp					\n"	\
+	"	mflo %0, $ac3					\n"	\
+	"	.set pop					\n" 	\
+	: "=r" (mflo3)); 						\
+	mflo3;								\
+})
+
+#define mfhi0()								\
+({									\
+	long mfhi0;							\
+	__asm__(							\
+	"	.set push					\n"	\
+	"	.set " MIPS_ISA_LEVEL "				\n"	\
+	"	.set dsp					\n"	\
+	"	mfhi %0, $ac0					\n"	\
+	"	.set pop					\n" 	\
+	: "=r" (mfhi0)); 						\
+	mfhi0;								\
+})
+
+#define mfhi1()								\
+({									\
+	long mfhi1;							\
+	__asm__(							\
+	"	.set push					\n"	\
+	"	.set " MIPS_ISA_LEVEL "				\n"	\
+	"	.set dsp					\n"	\
+	"	mfhi %0, $ac1					\n"	\
+	"	.set pop					\n" 	\
+	: "=r" (mfhi1)); 						\
+	mfhi1;								\
+})
+
+#define mfhi2()								\
+({									\
+	long mfhi2;							\
+	__asm__(							\
+	"	.set push					\n"	\
+	"	.set " MIPS_ISA_LEVEL "				\n"	\
+	"	.set dsp					\n"	\
+	"	mfhi %0, $ac2					\n"	\
+	"	.set pop					\n" 	\
+	: "=r" (mfhi2)); 						\
+	mfhi2;								\
+})
+
+#define mfhi3()								\
+({									\
+	long mfhi3;							\
+	__asm__(							\
+	"	.set push					\n"	\
+	"	.set " MIPS_ISA_LEVEL "				\n"	\
+	"	.set dsp					\n"	\
+	"	mfhi %0, $ac3					\n"	\
+	"	.set pop					\n" 	\
+	: "=r" (mfhi3)); 						\
+	mfhi3;								\
+})
+
+
+#define mtlo0(x)							\
+({									\
+	__asm__(							\
+	"	.set push					\n"	\
+	"	.set " MIPS_ISA_LEVEL "				\n"	\
+	"	.set dsp					\n"	\
+	"	mtlo %0, $ac0					\n"	\
+	"	.set pop					\n"	\
+	:								\
+	: "r" (x));							\
+})
+
+#define mtlo1(x)							\
+({									\
+	__asm__(							\
+	"	.set push					\n"	\
+	"	.set " MIPS_ISA_LEVEL "				\n"	\
+	"	.set dsp					\n"	\
+	"	mtlo %0, $ac1					\n"	\
+	"	.set pop					\n"	\
+	:								\
+	: "r" (x));							\
+})
+
+#define mtlo2(x)							\
+({									\
+	__asm__(							\
+	"	.set push					\n"	\
+	"	.set " MIPS_ISA_LEVEL "				\n"	\
+	"	.set dsp					\n"	\
+	"	mtlo %0, $ac2					\n"	\
+	"	.set pop					\n"	\
+	:								\
+	: "r" (x));							\
+})
+
+#define mtlo3(x)							\
+({									\
+	__asm__(							\
+	"	.set push					\n"	\
+	"	.set " MIPS_ISA_LEVEL "				\n"	\
+	"	.set dsp					\n"	\
+	"	mtlo %0, $ac3					\n"	\
+	"	.set pop					\n"	\
+	:								\
+	: "r" (x));							\
+})
+
+#define mthi0(x)							\
+({									\
+	__asm__(							\
+	"	.set push					\n"	\
+	"	.set " MIPS_ISA_LEVEL "				\n"	\
+	"	.set dsp					\n"	\
+	"	mthi %0, $ac0					\n"	\
+	"	.set pop					\n"	\
+	:								\
+	: "r" (x));							\
+})
+
+#define mthi1(x)							\
+({									\
+	__asm__(							\
+	"	.set push					\n"	\
+	"	.set " MIPS_ISA_LEVEL "				\n"	\
+	"	.set dsp					\n"	\
+	"	mthi %0, $ac1					\n"	\
+	"	.set pop					\n"	\
+	:								\
+	: "r" (x));							\
+})
+
+#define mthi2(x)							\
+({									\
+	__asm__(							\
+	"	.set push					\n"	\
+	"	.set " MIPS_ISA_LEVEL "				\n"	\
+	"	.set dsp					\n"	\
+	"	mthi %0, $ac2					\n"	\
+	"	.set pop					\n"	\
+	:								\
+	: "r" (x));							\
+})
+
+#define mthi3(x)							\
+({									\
+	__asm__(							\
+	"	.set push					\n"	\
+	"	.set " MIPS_ISA_LEVEL "				\n"	\
+	"	.set dsp					\n"	\
+	"	mthi %0, $ac3					\n"	\
+	"	.set pop					\n"	\
+	:								\
+	: "r" (x));							\
+})
+
+#else
+
+#define rddsp(mask)							\
+({									\
+	unsigned int __res;						\
+									\
+	__asm__ __volatile__(						\
+	"	.set	push					\n"	\
+	"	.set	noat					\n"	\
+	"	# rddsp $1, %x1					\n"	\
+	_ASM_INSN_IF_MIPS(0x7c000cb8 | (%x1 << 16))			\
+	_ASM_INSN32_IF_MM(0x0020067c | (%x1 << 14))			\
+	"	move	%0, $1					\n"	\
+	"	.set	pop					\n"	\
+	: "=r" (__res)							\
+	: "i" (mask));							\
+	__res;								\
+})
+
+#define wrdsp(val, mask)						\
+do {									\
+	__asm__ __volatile__(						\
+	"	.set	push					\n"	\
+	"	.set	noat					\n"	\
+	"	move	$1, %0					\n"	\
+	"	# wrdsp $1, %x1					\n"	\
+	_ASM_INSN_IF_MIPS(0x7c2004f8 | (%x1 << 11))			\
+	_ASM_INSN32_IF_MM(0x0020167c | (%x1 << 14))			\
+	"	.set	pop					\n"	\
+	:								\
+	: "r" (val), "i" (mask));					\
+} while (0)
+
+#define _dsp_mfxxx(ins)							\
+({									\
+	unsigned long __treg;						\
+									\
+	__asm__ __volatile__(						\
+	"	.set	push					\n"	\
+	"	.set	noat					\n"	\
+	_ASM_INSN_IF_MIPS(0x00000810 | %X1)				\
+	_ASM_INSN32_IF_MM(0x0001007c | %x1)				\
+	"	move	%0, $1					\n"	\
+	"	.set	pop					\n"	\
+	: "=r" (__treg)							\
+	: "i" (ins));							\
+	__treg;								\
+})
+
+#define _dsp_mtxxx(val, ins)						\
+do {									\
+	__asm__ __volatile__(						\
+	"	.set	push					\n"	\
+	"	.set	noat					\n"	\
+	"	move	$1, %0					\n"	\
+	_ASM_INSN_IF_MIPS(0x00200011 | %X1)				\
+	_ASM_INSN32_IF_MM(0x0001207c | %x1)				\
+	"	.set	pop					\n"	\
+	:								\
+	: "r" (val), "i" (ins));					\
+} while (0)
+
+#ifdef CONFIG_CPU_MICROMIPS
+
+#define _dsp_mflo(reg) _dsp_mfxxx((reg << 14) | 0x1000)
+#define _dsp_mfhi(reg) _dsp_mfxxx((reg << 14) | 0x0000)
+
+#define _dsp_mtlo(val, reg) _dsp_mtxxx(val, ((reg << 14) | 0x1000))
+#define _dsp_mthi(val, reg) _dsp_mtxxx(val, ((reg << 14) | 0x0000))
+
+#else  /* !CONFIG_CPU_MICROMIPS */
+
+#define _dsp_mflo(reg) _dsp_mfxxx((reg << 21) | 0x0002)
+#define _dsp_mfhi(reg) _dsp_mfxxx((reg << 21) | 0x0000)
+
+#define _dsp_mtlo(val, reg) _dsp_mtxxx(val, ((reg << 11) | 0x0002))
+#define _dsp_mthi(val, reg) _dsp_mtxxx(val, ((reg << 11) | 0x0000))
+
+#endif /* CONFIG_CPU_MICROMIPS */
+
+#define mflo0() _dsp_mflo(0)
+#define mflo1() _dsp_mflo(1)
+#define mflo2() _dsp_mflo(2)
+#define mflo3() _dsp_mflo(3)
+
+#define mfhi0() _dsp_mfhi(0)
+#define mfhi1() _dsp_mfhi(1)
+#define mfhi2() _dsp_mfhi(2)
+#define mfhi3() _dsp_mfhi(3)
+
+#define mtlo0(x) _dsp_mtlo(x, 0)
+#define mtlo1(x) _dsp_mtlo(x, 1)
+#define mtlo2(x) _dsp_mtlo(x, 2)
+#define mtlo3(x) _dsp_mtlo(x, 3)
+
+#define mthi0(x) _dsp_mthi(x, 0)
+#define mthi1(x) _dsp_mthi(x, 1)
+#define mthi2(x) _dsp_mthi(x, 2)
+#define mthi3(x) _dsp_mthi(x, 3)
+
+#endif
+
+/*
+ * TLB operations.
+ *
+ * It is responsibility of the caller to take care of any TLB hazards.
+ */
+static inline void tlb_probe(void)
+{
+	__asm__ __volatile__(
+		".set noreorder\n\t"
+		"tlbp\n\t"
+		".set reorder");
+}
+
+static inline void tlb_read(void)
+{
+#ifdef CONFIG_WAR_MIPS34K_MISSED_ITLB
+	int res = 0;
+
+	__asm__ __volatile__(
+	"	.set	push					\n"
+	"	.set	noreorder				\n"
+	"	.set	noat					\n"
+	"	.set	mips32r2				\n"
+	"	.word	0x41610001		# dvpe $1	\n"
+	"	move	%0, $1					\n"
+	"	ehb						\n"
+	"	.set	pop					\n"
+	: "=r" (res));
+
+	instruction_hazard();
+#endif
+
+	__asm__ __volatile__(
+		".set noreorder\n\t"
+		"tlbr\n\t"
+		".set reorder");
+
+#ifdef CONFIG_WAR_MIPS34K_MISSED_ITLB
+	if ((res & _ULCAST_(1)))
+		__asm__ __volatile__(
+		"	.set	push				\n"
+		"	.set	noreorder			\n"
+		"	.set	noat				\n"
+		"	.set	mips32r2			\n"
+		"	.word	0x41600021	# evpe		\n"
+		"	ehb					\n"
+		"	.set	pop				\n");
+#endif
+}
+
+static inline void tlb_write_indexed(void)
+{
+	__asm__ __volatile__(
+		".set noreorder\n\t"
+		"tlbwi\n\t"
+		".set reorder");
+}
+
+static inline void tlb_write_random(void)
+{
+	__asm__ __volatile__(
+		".set noreorder\n\t"
+		"tlbwr\n\t"
+		".set reorder");
+}
+
+/*
+ * Guest TLB operations.
+ *
+ * It is responsibility of the caller to take care of any TLB hazards.
+ */
+static inline void guest_tlb_probe(void)
+{
+	__asm__ __volatile__(
+		".set push\n\t"
+		".set noreorder\n\t"
+		__tlbgp()
+		".set pop");
+}
+
+static inline void guest_tlb_read(void)
+{
+	__asm__ __volatile__(
+		".set push\n\t"
+		".set noreorder\n\t"
+		__tlbgr()
+		".set pop");
+}
+
+static inline void guest_tlb_write_indexed(void)
+{
+	__asm__ __volatile__(
+		".set push\n\t"
+		".set noreorder\n\t"
+		__tlbgwi()
+		".set pop");
+}
+
+static inline void guest_tlb_write_random(void)
+{
+	__asm__ __volatile__(
+		".set push\n\t"
+		".set noreorder\n\t"
+		__tlbgwr()
+		".set pop");
+}
+
+/*
+ * Guest TLB Invalidate Flush
+ */
+static inline void guest_tlbinvf(void)
+{
+	__asm__ __volatile__(
+		".set push\n\t"
+		".set noreorder\n\t"
+		__tlbginvf()
+		".set pop");
+}
+
+/*
+ * Manipulate bits in a register.
+ */
+#define __BUILD_SET_COMMON(name)				\
+static inline unsigned int					\
+set_##name(unsigned int set)					\
+{								\
+	unsigned int res, new;					\
+								\
+	res = read_##name();					\
+	new = res | set;					\
+	write_##name(new);					\
+								\
+	return res;						\
+}								\
+								\
+static inline unsigned int					\
+clear_##name(unsigned int clear)				\
+{								\
+	unsigned int res, new;					\
+								\
+	res = read_##name();					\
+	new = res & ~clear;					\
+	write_##name(new);					\
+								\
+	return res;						\
+}								\
+								\
+static inline unsigned int					\
+change_##name(unsigned int change, unsigned int val)		\
+{								\
+	unsigned int res, new;					\
+								\
+	res = read_##name();					\
+	new = res & ~change;					\
+	new |= (val & change);					\
+	write_##name(new);					\
+								\
+	return res;						\
+}
+
+/*
+ * Manipulate bits in a c0 register.
+ */
+#define __BUILD_SET_C0(name)	__BUILD_SET_COMMON(c0_##name)
+
+__BUILD_SET_C0(status)
+__BUILD_SET_C0(cause)
+__BUILD_SET_C0(config)
+__BUILD_SET_C0(config5)
+__BUILD_SET_C0(config6)
+__BUILD_SET_C0(config7)
+__BUILD_SET_C0(diag)
+__BUILD_SET_C0(intcontrol)
+__BUILD_SET_C0(intctl)
+__BUILD_SET_C0(srsmap)
+__BUILD_SET_C0(pagegrain)
+__BUILD_SET_C0(guestctl0)
+__BUILD_SET_C0(guestctl0ext)
+__BUILD_SET_C0(guestctl1)
+__BUILD_SET_C0(guestctl2)
+__BUILD_SET_C0(guestctl3)
+__BUILD_SET_C0(brcm_config_0)
+__BUILD_SET_C0(brcm_bus_pll)
+__BUILD_SET_C0(brcm_reset)
+__BUILD_SET_C0(brcm_cmt_intr)
+__BUILD_SET_C0(brcm_cmt_ctrl)
+__BUILD_SET_C0(brcm_config)
+__BUILD_SET_C0(brcm_mode)
+
+/*
+ * Manipulate bits in a guest c0 register.
+ */
+#define __BUILD_SET_GC0(name)	__BUILD_SET_COMMON(gc0_##name)
+
+__BUILD_SET_GC0(wired)
+__BUILD_SET_GC0(status)
+__BUILD_SET_GC0(cause)
+__BUILD_SET_GC0(ebase)
+__BUILD_SET_GC0(config1)
+
+/*
+ * Return low 10 bits of ebase.
+ * Note that under KVM (MIPSVZ) this returns vcpu id.
+ */
+static inline unsigned int get_ebase_cpunum(void)
+{
+	return read_c0_ebase() & MIPS_EBASE_CPUNUM;
+}
+
+#endif /* !__ASSEMBLY__ */
+
+#endif /* _ASM_MIPSREGS_H */
diff --git a/arch/mips/include/asm/mmiowb.h b/arch/mips/include/asm/mmiowb.h
new file mode 100644
index 000000000..a40824e3e
--- /dev/null
+++ b/arch/mips/include/asm/mmiowb.h
@@ -0,0 +1,11 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _ASM_MMIOWB_H
+#define _ASM_MMIOWB_H
+
+#include <asm/io.h>
+
+#define mmiowb()	iobarrier_w()
+
+#include <asm-generic/mmiowb.h>
+
+#endif	/* _ASM_MMIOWB_H */
diff --git a/arch/mips/include/asm/mmu.h b/arch/mips/include/asm/mmu.h
new file mode 100644
index 000000000..5df0238f6
--- /dev/null
+++ b/arch/mips/include/asm/mmu.h
@@ -0,0 +1,25 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_MMU_H
+#define __ASM_MMU_H
+
+#include <linux/atomic.h>
+#include <linux/spinlock.h>
+#include <linux/wait.h>
+
+typedef struct {
+	union {
+		u64 asid[NR_CPUS];
+		atomic64_t mmid;
+	};
+
+	void *vdso;
+
+	/* lock to be held whilst modifying fp_bd_emupage_allocmap */
+	spinlock_t bd_emupage_lock;
+	/* bitmap tracking allocation of fp_bd_emupage */
+	unsigned long *bd_emupage_allocmap;
+	/* wait queue for threads requiring an emuframe */
+	wait_queue_head_t bd_emupage_queue;
+} mm_context_t;
+
+#endif /* __ASM_MMU_H */
diff --git a/arch/mips/include/asm/mmu_context.h b/arch/mips/include/asm/mmu_context.h
new file mode 100644
index 000000000..ed9f2d748
--- /dev/null
+++ b/arch/mips/include/asm/mmu_context.h
@@ -0,0 +1,237 @@
+/*
+ * Switch a MMU context.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1996, 1997, 1998, 1999 by Ralf Baechle
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_MMU_CONTEXT_H
+#define _ASM_MMU_CONTEXT_H
+
+#include <linux/errno.h>
+#include <linux/sched.h>
+#include <linux/mm_types.h>
+#include <linux/smp.h>
+#include <linux/slab.h>
+
+#include <asm/barrier.h>
+#include <asm/cacheflush.h>
+#include <asm/dsemul.h>
+#include <asm/ginvt.h>
+#include <asm/hazards.h>
+#include <asm/tlbflush.h>
+#include <asm-generic/mm_hooks.h>
+
+#define htw_set_pwbase(pgd)						\
+do {									\
+	if (cpu_has_htw) {						\
+		write_c0_pwbase(pgd);					\
+		back_to_back_c0_hazard();				\
+	}								\
+} while (0)
+
+extern void tlbmiss_handler_setup_pgd(unsigned long);
+extern char tlbmiss_handler_setup_pgd_end[];
+
+/* Note: This is also implemented with uasm in arch/mips/kvm/entry.c */
+#define TLBMISS_HANDLER_SETUP_PGD(pgd)					\
+do {									\
+	tlbmiss_handler_setup_pgd((unsigned long)(pgd));		\
+	htw_set_pwbase((unsigned long)pgd);				\
+} while (0)
+
+#ifdef CONFIG_MIPS_PGD_C0_CONTEXT
+
+#define TLBMISS_HANDLER_RESTORE()					\
+	write_c0_xcontext((unsigned long) smp_processor_id() <<		\
+			  SMP_CPUID_REGSHIFT)
+
+#define TLBMISS_HANDLER_SETUP()						\
+	do {								\
+		TLBMISS_HANDLER_SETUP_PGD(swapper_pg_dir);		\
+		TLBMISS_HANDLER_RESTORE();				\
+	} while (0)
+
+#else /* !CONFIG_MIPS_PGD_C0_CONTEXT: using  pgd_current*/
+
+/*
+ * For the fast tlb miss handlers, we keep a per cpu array of pointers
+ * to the current pgd for each processor. Also, the proc. id is stuffed
+ * into the context register.
+ */
+extern unsigned long pgd_current[];
+
+#define TLBMISS_HANDLER_RESTORE()					\
+	write_c0_context((unsigned long) smp_processor_id() <<		\
+			 SMP_CPUID_REGSHIFT)
+
+#define TLBMISS_HANDLER_SETUP()						\
+	TLBMISS_HANDLER_RESTORE();					\
+	back_to_back_c0_hazard();					\
+	TLBMISS_HANDLER_SETUP_PGD(swapper_pg_dir)
+#endif /* CONFIG_MIPS_PGD_C0_CONTEXT*/
+
+/*
+ * The ginvt instruction will invalidate wired entries when its type field
+ * targets anything other than the entire TLB. That means that if we were to
+ * allow the kernel to create wired entries with the MMID of current->active_mm
+ * then those wired entries could be invalidated when we later use ginvt to
+ * invalidate TLB entries with that MMID.
+ *
+ * In order to prevent ginvt from trashing wired entries, we reserve one MMID
+ * for use by the kernel when creating wired entries. This MMID will never be
+ * assigned to a struct mm, and we'll never target it with a ginvt instruction.
+ */
+#define MMID_KERNEL_WIRED	0
+
+/*
+ *  All unused by hardware upper bits will be considered
+ *  as a software asid extension.
+ */
+static inline u64 asid_version_mask(unsigned int cpu)
+{
+	unsigned long asid_mask = cpu_asid_mask(&cpu_data[cpu]);
+
+	return ~(u64)(asid_mask | (asid_mask - 1));
+}
+
+static inline u64 asid_first_version(unsigned int cpu)
+{
+	return ~asid_version_mask(cpu) + 1;
+}
+
+static inline u64 cpu_context(unsigned int cpu, const struct mm_struct *mm)
+{
+	if (cpu_has_mmid)
+		return atomic64_read(&mm->context.mmid);
+
+	return mm->context.asid[cpu];
+}
+
+static inline void set_cpu_context(unsigned int cpu,
+				   struct mm_struct *mm, u64 ctx)
+{
+	if (cpu_has_mmid)
+		atomic64_set(&mm->context.mmid, ctx);
+	else
+		mm->context.asid[cpu] = ctx;
+}
+
+#define asid_cache(cpu)		(cpu_data[cpu].asid_cache)
+#define cpu_asid(cpu, mm) \
+	(cpu_context((cpu), (mm)) & cpu_asid_mask(&cpu_data[cpu]))
+
+extern void get_new_mmu_context(struct mm_struct *mm);
+extern void check_mmu_context(struct mm_struct *mm);
+extern void check_switch_mmu_context(struct mm_struct *mm);
+
+/*
+ * Initialize the context related info for a new mm_struct
+ * instance.
+ */
+#define init_new_context init_new_context
+static inline int
+init_new_context(struct task_struct *tsk, struct mm_struct *mm)
+{
+	int i;
+
+	if (cpu_has_mmid) {
+		set_cpu_context(0, mm, 0);
+	} else {
+		for_each_possible_cpu(i)
+			set_cpu_context(i, mm, 0);
+	}
+
+	mm->context.bd_emupage_allocmap = NULL;
+	spin_lock_init(&mm->context.bd_emupage_lock);
+	init_waitqueue_head(&mm->context.bd_emupage_queue);
+
+	return 0;
+}
+
+static inline void switch_mm(struct mm_struct *prev, struct mm_struct *next,
+			     struct task_struct *tsk)
+{
+	unsigned int cpu = smp_processor_id();
+	unsigned long flags;
+	local_irq_save(flags);
+
+	htw_stop();
+	check_switch_mmu_context(next);
+
+	/*
+	 * Mark current->active_mm as not "active" anymore.
+	 * We don't want to mislead possible IPI tlb flush routines.
+	 */
+	cpumask_clear_cpu(cpu, mm_cpumask(prev));
+	cpumask_set_cpu(cpu, mm_cpumask(next));
+	htw_start();
+
+	local_irq_restore(flags);
+}
+
+/*
+ * Destroy context related info for an mm_struct that is about
+ * to be put to rest.
+ */
+#define destroy_context destroy_context
+static inline void destroy_context(struct mm_struct *mm)
+{
+	dsemul_mm_cleanup(mm);
+}
+
+static inline void
+drop_mmu_context(struct mm_struct *mm)
+{
+	unsigned long flags;
+	unsigned int cpu;
+	u32 old_mmid;
+	u64 ctx;
+
+	local_irq_save(flags);
+
+	cpu = smp_processor_id();
+	ctx = cpu_context(cpu, mm);
+
+	if (!ctx) {
+		/* no-op */
+	} else if (cpu_has_mmid) {
+		/*
+		 * Globally invalidating TLB entries associated with the MMID
+		 * is pretty cheap using the GINVT instruction, so we'll do
+		 * that rather than incur the overhead of allocating a new
+		 * MMID. The latter would be especially difficult since MMIDs
+		 * are global & other CPUs may be actively using ctx.
+		 */
+		htw_stop();
+		old_mmid = read_c0_memorymapid();
+		write_c0_memorymapid(ctx & cpu_asid_mask(&cpu_data[cpu]));
+		mtc0_tlbw_hazard();
+		ginvt_mmid();
+		sync_ginv();
+		write_c0_memorymapid(old_mmid);
+		instruction_hazard();
+		htw_start();
+	} else if (cpumask_test_cpu(cpu, mm_cpumask(mm))) {
+		/*
+		 * mm is currently active, so we can't really drop it.
+		 * Instead we bump the ASID.
+		 */
+		htw_stop();
+		get_new_mmu_context(mm);
+		write_c0_entryhi(cpu_asid(cpu, mm));
+		htw_start();
+	} else {
+		/* will get a new context next time */
+		set_cpu_context(cpu, mm, 0);
+	}
+
+	local_irq_restore(flags);
+}
+
+#include <asm-generic/mmu_context.h>
+
+#endif /* _ASM_MMU_CONTEXT_H */
diff --git a/arch/mips/include/asm/mmzone.h b/arch/mips/include/asm/mmzone.h
new file mode 100644
index 000000000..602a21aee
--- /dev/null
+++ b/arch/mips/include/asm/mmzone.h
@@ -0,0 +1,23 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Written by Kanoj Sarcar (kanoj@sgi.com) Aug 99
+ * Rewritten for Linux 2.6 by Christoph Hellwig (hch@lst.de) Jan 2004
+ */
+#ifndef _ASM_MMZONE_H_
+#define _ASM_MMZONE_H_
+
+#include <asm/page.h>
+
+#ifdef CONFIG_NUMA
+# include <mmzone.h>
+#endif
+
+#ifndef pa_to_nid
+#define pa_to_nid(addr) 0
+#endif
+
+#ifndef nid_to_addrbase
+#define nid_to_addrbase(nid) 0
+#endif
+
+#endif /* _ASM_MMZONE_H_ */
diff --git a/arch/mips/include/asm/module.h b/arch/mips/include/asm/module.h
new file mode 100644
index 000000000..724a08825
--- /dev/null
+++ b/arch/mips/include/asm/module.h
@@ -0,0 +1,86 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _ASM_MODULE_H
+#define _ASM_MODULE_H
+
+#include <linux/list.h>
+#include <linux/elf.h>
+#include <asm/extable.h>
+
+struct mod_arch_specific {
+	/* Data Bus Error exception tables */
+	struct list_head dbe_list;
+	const struct exception_table_entry *dbe_start;
+	const struct exception_table_entry *dbe_end;
+	struct mips_hi16 *r_mips_hi16_list;
+};
+
+typedef uint8_t Elf64_Byte;		/* Type for a 8-bit quantity.  */
+
+typedef struct {
+	Elf64_Addr r_offset;			/* Address of relocation.  */
+	Elf64_Word r_sym;			/* Symbol index.  */
+	Elf64_Byte r_ssym;			/* Special symbol.  */
+	Elf64_Byte r_type3;			/* Third relocation.  */
+	Elf64_Byte r_type2;			/* Second relocation.  */
+	Elf64_Byte r_type;			/* First relocation.  */
+} Elf64_Mips_Rel;
+
+typedef struct {
+	Elf64_Addr r_offset;			/* Address of relocation.  */
+	Elf64_Word r_sym;			/* Symbol index.  */
+	Elf64_Byte r_ssym;			/* Special symbol.  */
+	Elf64_Byte r_type3;			/* Third relocation.  */
+	Elf64_Byte r_type2;			/* Second relocation.  */
+	Elf64_Byte r_type;			/* First relocation.  */
+	Elf64_Sxword r_addend;			/* Addend.  */
+} Elf64_Mips_Rela;
+
+#ifdef CONFIG_32BIT
+#define Elf_Shdr	Elf32_Shdr
+#define Elf_Sym		Elf32_Sym
+#define Elf_Ehdr	Elf32_Ehdr
+#define Elf_Addr	Elf32_Addr
+#define Elf_Rel		Elf32_Rel
+#define Elf_Rela	Elf32_Rela
+#define ELF_R_TYPE(X)	ELF32_R_TYPE(X)
+#define ELF_R_SYM(X)	ELF32_R_SYM(X)
+
+#define Elf_Mips_Rel	Elf32_Rel
+#define Elf_Mips_Rela	Elf32_Rela
+
+#define ELF_MIPS_R_SYM(rel) ELF32_R_SYM((rel).r_info)
+#define ELF_MIPS_R_TYPE(rel) ELF32_R_TYPE((rel).r_info)
+
+#endif
+
+#ifdef CONFIG_64BIT
+#define Elf_Shdr	Elf64_Shdr
+#define Elf_Sym		Elf64_Sym
+#define Elf_Ehdr	Elf64_Ehdr
+#define Elf_Addr	Elf64_Addr
+#define Elf_Rel		Elf64_Rel
+#define Elf_Rela	Elf64_Rela
+#define ELF_R_TYPE(X)	ELF64_R_TYPE(X)
+#define ELF_R_SYM(X)	ELF64_R_SYM(X)
+
+#define Elf_Mips_Rel	Elf64_Mips_Rel
+#define Elf_Mips_Rela	Elf64_Mips_Rela
+
+#define ELF_MIPS_R_SYM(rel) ((rel).r_sym)
+#define ELF_MIPS_R_TYPE(rel) ((rel).r_type)
+
+#endif
+
+#ifdef CONFIG_MODULES
+/* Given an address, look for it in the exception tables. */
+const struct exception_table_entry*search_module_dbetables(unsigned long addr);
+#else
+/* Given an address, look for it in the exception tables. */
+static inline const struct exception_table_entry *
+search_module_dbetables(unsigned long addr)
+{
+	return NULL;
+}
+#endif
+
+#endif /* _ASM_MODULE_H */
diff --git a/arch/mips/include/asm/msa.h b/arch/mips/include/asm/msa.h
new file mode 100644
index 000000000..236a49ee2
--- /dev/null
+++ b/arch/mips/include/asm/msa.h
@@ -0,0 +1,290 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2013 Imagination Technologies
+ * Author: Paul Burton <paul.burton@mips.com>
+ */
+#ifndef _ASM_MSA_H
+#define _ASM_MSA_H
+
+#include <asm/mipsregs.h>
+
+#ifndef __ASSEMBLY__
+
+#include <asm/inst.h>
+
+extern void _save_msa(struct task_struct *);
+extern void _restore_msa(struct task_struct *);
+extern void _init_msa_upper(void);
+
+extern void read_msa_wr_b(unsigned idx, union fpureg *to);
+extern void read_msa_wr_h(unsigned idx, union fpureg *to);
+extern void read_msa_wr_w(unsigned idx, union fpureg *to);
+extern void read_msa_wr_d(unsigned idx, union fpureg *to);
+
+/**
+ * read_msa_wr() - Read a single MSA vector register
+ * @idx:	The index of the vector register to read
+ * @to:		The FPU register union to store the registers value in
+ * @fmt:	The format of the data in the vector register
+ *
+ * Read the value of MSA vector register idx into the FPU register
+ * union to, using the format fmt.
+ */
+static inline void read_msa_wr(unsigned idx, union fpureg *to,
+			       enum msa_2b_fmt fmt)
+{
+	switch (fmt) {
+	case msa_fmt_b:
+		read_msa_wr_b(idx, to);
+		break;
+
+	case msa_fmt_h:
+		read_msa_wr_h(idx, to);
+		break;
+
+	case msa_fmt_w:
+		read_msa_wr_w(idx, to);
+		break;
+
+	case msa_fmt_d:
+		read_msa_wr_d(idx, to);
+		break;
+
+	default:
+		BUG();
+	}
+}
+
+extern void write_msa_wr_b(unsigned idx, union fpureg *from);
+extern void write_msa_wr_h(unsigned idx, union fpureg *from);
+extern void write_msa_wr_w(unsigned idx, union fpureg *from);
+extern void write_msa_wr_d(unsigned idx, union fpureg *from);
+
+/**
+ * write_msa_wr() - Write a single MSA vector register
+ * @idx:	The index of the vector register to write
+ * @from:	The FPU register union to take the registers value from
+ * @fmt:	The format of the data in the vector register
+ *
+ * Write the value from the FPU register union from into MSA vector
+ * register idx, using the format fmt.
+ */
+static inline void write_msa_wr(unsigned idx, union fpureg *from,
+				enum msa_2b_fmt fmt)
+{
+	switch (fmt) {
+	case msa_fmt_b:
+		write_msa_wr_b(idx, from);
+		break;
+
+	case msa_fmt_h:
+		write_msa_wr_h(idx, from);
+		break;
+
+	case msa_fmt_w:
+		write_msa_wr_w(idx, from);
+		break;
+
+	case msa_fmt_d:
+		write_msa_wr_d(idx, from);
+		break;
+
+	default:
+		BUG();
+	}
+}
+
+static inline void enable_msa(void)
+{
+	if (cpu_has_msa) {
+		set_c0_config5(MIPS_CONF5_MSAEN);
+		enable_fpu_hazard();
+	}
+}
+
+static inline void disable_msa(void)
+{
+	if (cpu_has_msa) {
+		clear_c0_config5(MIPS_CONF5_MSAEN);
+		disable_fpu_hazard();
+	}
+}
+
+static inline int is_msa_enabled(void)
+{
+	if (!cpu_has_msa)
+		return 0;
+
+	return read_c0_config5() & MIPS_CONF5_MSAEN;
+}
+
+static inline int thread_msa_context_live(void)
+{
+	/*
+	 * Check cpu_has_msa only if it's a constant. This will allow the
+	 * compiler to optimise out code for CPUs without MSA without adding
+	 * an extra redundant check for CPUs with MSA.
+	 */
+	if (__builtin_constant_p(cpu_has_msa) && !cpu_has_msa)
+		return 0;
+
+	return test_thread_flag(TIF_MSA_CTX_LIVE);
+}
+
+static inline void save_msa(struct task_struct *t)
+{
+	if (cpu_has_msa)
+		_save_msa(t);
+}
+
+static inline void restore_msa(struct task_struct *t)
+{
+	if (cpu_has_msa)
+		_restore_msa(t);
+}
+
+static inline void init_msa_upper(void)
+{
+	/*
+	 * Check cpu_has_msa only if it's a constant. This will allow the
+	 * compiler to optimise out code for CPUs without MSA without adding
+	 * an extra redundant check for CPUs with MSA.
+	 */
+	if (__builtin_constant_p(cpu_has_msa) && !cpu_has_msa)
+		return;
+
+	_init_msa_upper();
+}
+
+#ifndef TOOLCHAIN_SUPPORTS_MSA
+/*
+ * Define assembler macros using .word for the c[ft]cmsa instructions in order
+ * to allow compilation with toolchains that do not support MSA. Once all
+ * toolchains in use support MSA these can be removed.
+ */
+
+#define _ASM_SET_CFCMSA							\
+	_ASM_MACRO_2R(cfcmsa, rd, cs,					\
+		      _ASM_INSN_IF_MIPS(0x787e0019 | __cs << 11 | __rd << 6)	\
+		      _ASM_INSN32_IF_MM(0x587e0016 | __cs << 11 | __rd << 6))
+#define _ASM_UNSET_CFCMSA ".purgem cfcmsa\n\t"
+#define _ASM_SET_CTCMSA							\
+	_ASM_MACRO_2R(ctcmsa, cd, rs,					\
+		      _ASM_INSN_IF_MIPS(0x783e0019 | __rs << 11 | __cd << 6)	\
+		      _ASM_INSN32_IF_MM(0x583e0016 | __rs << 11 | __cd << 6))
+#define _ASM_UNSET_CTCMSA ".purgem ctcmsa\n\t"
+#else /* TOOLCHAIN_SUPPORTS_MSA */
+#define _ASM_SET_CFCMSA						\
+		".set\tfp=64\n\t"				\
+		".set\tmsa\n\t"
+#define _ASM_UNSET_CFCMSA
+#define _ASM_SET_CTCMSA						\
+		".set\tfp=64\n\t"				\
+		".set\tmsa\n\t"
+#define _ASM_UNSET_CTCMSA
+#endif
+
+#define __BUILD_MSA_CTL_REG(name, cs)				\
+static inline unsigned int read_msa_##name(void)		\
+{								\
+	unsigned int reg;					\
+	__asm__ __volatile__(					\
+	"	.set	push\n"					\
+	_ASM_SET_CFCMSA						\
+	"	cfcmsa	%0, $" #cs "\n"				\
+	_ASM_UNSET_CFCMSA					\
+	"	.set	pop\n"					\
+	: "=r"(reg));						\
+	return reg;						\
+}								\
+								\
+static inline void write_msa_##name(unsigned int val)		\
+{								\
+	__asm__ __volatile__(					\
+	"	.set	push\n"					\
+	_ASM_SET_CTCMSA						\
+	"	ctcmsa	$" #cs ", %0\n"				\
+	_ASM_UNSET_CTCMSA					\
+	"	.set	pop\n"					\
+	: : "r"(val));						\
+}
+
+__BUILD_MSA_CTL_REG(ir, 0)
+__BUILD_MSA_CTL_REG(csr, 1)
+__BUILD_MSA_CTL_REG(access, 2)
+__BUILD_MSA_CTL_REG(save, 3)
+__BUILD_MSA_CTL_REG(modify, 4)
+__BUILD_MSA_CTL_REG(request, 5)
+__BUILD_MSA_CTL_REG(map, 6)
+__BUILD_MSA_CTL_REG(unmap, 7)
+
+#endif /* !__ASSEMBLY__ */
+
+#define MSA_IR		0
+#define MSA_CSR		1
+#define MSA_ACCESS	2
+#define MSA_SAVE	3
+#define MSA_MODIFY	4
+#define MSA_REQUEST	5
+#define MSA_MAP		6
+#define MSA_UNMAP	7
+
+/* MSA Implementation Register (MSAIR) */
+#define MSA_IR_REVB		0
+#define MSA_IR_REVF		(_ULCAST_(0xff) << MSA_IR_REVB)
+#define MSA_IR_PROCB		8
+#define MSA_IR_PROCF		(_ULCAST_(0xff) << MSA_IR_PROCB)
+#define MSA_IR_WRPB		16
+#define MSA_IR_WRPF		(_ULCAST_(0x1) << MSA_IR_WRPB)
+
+/* MSA Control & Status Register (MSACSR) */
+#define MSA_CSR_RMB		0
+#define MSA_CSR_RMF		(_ULCAST_(0x3) << MSA_CSR_RMB)
+#define MSA_CSR_RM_NEAREST	0
+#define MSA_CSR_RM_TO_ZERO	1
+#define MSA_CSR_RM_TO_POS	2
+#define MSA_CSR_RM_TO_NEG	3
+#define MSA_CSR_FLAGSB		2
+#define MSA_CSR_FLAGSF		(_ULCAST_(0x1f) << MSA_CSR_FLAGSB)
+#define MSA_CSR_FLAGS_IB	2
+#define MSA_CSR_FLAGS_IF	(_ULCAST_(0x1) << MSA_CSR_FLAGS_IB)
+#define MSA_CSR_FLAGS_UB	3
+#define MSA_CSR_FLAGS_UF	(_ULCAST_(0x1) << MSA_CSR_FLAGS_UB)
+#define MSA_CSR_FLAGS_OB	4
+#define MSA_CSR_FLAGS_OF	(_ULCAST_(0x1) << MSA_CSR_FLAGS_OB)
+#define MSA_CSR_FLAGS_ZB	5
+#define MSA_CSR_FLAGS_ZF	(_ULCAST_(0x1) << MSA_CSR_FLAGS_ZB)
+#define MSA_CSR_FLAGS_VB	6
+#define MSA_CSR_FLAGS_VF	(_ULCAST_(0x1) << MSA_CSR_FLAGS_VB)
+#define MSA_CSR_ENABLESB	7
+#define MSA_CSR_ENABLESF	(_ULCAST_(0x1f) << MSA_CSR_ENABLESB)
+#define MSA_CSR_ENABLES_IB	7
+#define MSA_CSR_ENABLES_IF	(_ULCAST_(0x1) << MSA_CSR_ENABLES_IB)
+#define MSA_CSR_ENABLES_UB	8
+#define MSA_CSR_ENABLES_UF	(_ULCAST_(0x1) << MSA_CSR_ENABLES_UB)
+#define MSA_CSR_ENABLES_OB	9
+#define MSA_CSR_ENABLES_OF	(_ULCAST_(0x1) << MSA_CSR_ENABLES_OB)
+#define MSA_CSR_ENABLES_ZB	10
+#define MSA_CSR_ENABLES_ZF	(_ULCAST_(0x1) << MSA_CSR_ENABLES_ZB)
+#define MSA_CSR_ENABLES_VB	11
+#define MSA_CSR_ENABLES_VF	(_ULCAST_(0x1) << MSA_CSR_ENABLES_VB)
+#define MSA_CSR_CAUSEB		12
+#define MSA_CSR_CAUSEF		(_ULCAST_(0x3f) << MSA_CSR_CAUSEB)
+#define MSA_CSR_CAUSE_IB	12
+#define MSA_CSR_CAUSE_IF	(_ULCAST_(0x1) << MSA_CSR_CAUSE_IB)
+#define MSA_CSR_CAUSE_UB	13
+#define MSA_CSR_CAUSE_UF	(_ULCAST_(0x1) << MSA_CSR_CAUSE_UB)
+#define MSA_CSR_CAUSE_OB	14
+#define MSA_CSR_CAUSE_OF	(_ULCAST_(0x1) << MSA_CSR_CAUSE_OB)
+#define MSA_CSR_CAUSE_ZB	15
+#define MSA_CSR_CAUSE_ZF	(_ULCAST_(0x1) << MSA_CSR_CAUSE_ZB)
+#define MSA_CSR_CAUSE_VB	16
+#define MSA_CSR_CAUSE_VF	(_ULCAST_(0x1) << MSA_CSR_CAUSE_VB)
+#define MSA_CSR_CAUSE_EB	17
+#define MSA_CSR_CAUSE_EF	(_ULCAST_(0x1) << MSA_CSR_CAUSE_EB)
+#define MSA_CSR_NXB		18
+#define MSA_CSR_NXF		(_ULCAST_(0x1) << MSA_CSR_NXB)
+#define MSA_CSR_FSB		24
+#define MSA_CSR_FSF		(_ULCAST_(0x1) << MSA_CSR_FSB)
+
+#endif /* _ASM_MSA_H */
diff --git a/arch/mips/include/asm/msc01_ic.h b/arch/mips/include/asm/msc01_ic.h
new file mode 100644
index 000000000..ff7f074d0
--- /dev/null
+++ b/arch/mips/include/asm/msc01_ic.h
@@ -0,0 +1,147 @@
+/*
+ * PCI Register definitions for the MIPS System Controller.
+ *
+ * Copyright (C) 2004 MIPS Technologies, Inc.  All rights reserved.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+
+#ifndef __ASM_MIPS_BOARDS_MSC01_IC_H
+#define __ASM_MIPS_BOARDS_MSC01_IC_H
+
+/*****************************************************************************
+ * Register offset addresses
+ *****************************************************************************/
+
+#define MSC01_IC_RST_OFS     0x00008	/* Software reset	       */
+#define MSC01_IC_ENAL_OFS    0x00100	/* Int_in enable mask 31:0     */
+#define MSC01_IC_ENAH_OFS    0x00108	/* Int_in enable mask 63:32    */
+#define MSC01_IC_DISL_OFS    0x00120	/* Int_in disable mask 31:0    */
+#define MSC01_IC_DISH_OFS    0x00128	/* Int_in disable mask 63:32   */
+#define MSC01_IC_ISBL_OFS    0x00140	/* Raw int_in 31:0	       */
+#define MSC01_IC_ISBH_OFS    0x00148	/* Raw int_in 63:32	       */
+#define MSC01_IC_ISAL_OFS    0x00160	/* Masked int_in 31:0	       */
+#define MSC01_IC_ISAH_OFS    0x00168	/* Masked int_in 63:32	       */
+#define MSC01_IC_LVL_OFS     0x00180	/* Disable priority int_out    */
+#define MSC01_IC_RAMW_OFS    0x00180	/* Shadow set RAM (EI)	       */
+#define MSC01_IC_OSB_OFS     0x00188	/* Raw int_out		       */
+#define MSC01_IC_OSA_OFS     0x00190	/* Masked int_out	       */
+#define MSC01_IC_GENA_OFS    0x00198	/* Global HW int enable	       */
+#define MSC01_IC_BASE_OFS    0x001a0	/* Base address of IC_VEC      */
+#define MSC01_IC_VEC_OFS     0x001b0	/* Active int's vector address */
+#define MSC01_IC_EOI_OFS     0x001c0	/* Enable lower level ints     */
+#define MSC01_IC_CFG_OFS     0x001c8	/* Configuration register      */
+#define MSC01_IC_TRLD_OFS    0x001d0	/* Interval timer reload val   */
+#define MSC01_IC_TVAL_OFS    0x001e0	/* Interval timer current val  */
+#define MSC01_IC_TCFG_OFS    0x001f0	/* Interval timer config       */
+#define MSC01_IC_SUP_OFS     0x00200	/* Set up int_in line 0	       */
+#define MSC01_IC_ENA_OFS     0x00800	/* Int_in enable mask 63:0     */
+#define MSC01_IC_DIS_OFS     0x00820	/* Int_in disable mask 63:0    */
+#define MSC01_IC_ISB_OFS     0x00840	/* Raw int_in 63:0	       */
+#define MSC01_IC_ISA_OFS     0x00860	/* Masked int_in 63:0	       */
+
+/*****************************************************************************
+ * Register field encodings
+ *****************************************************************************/
+
+#define MSC01_IC_RST_RST_SHF	  0
+#define MSC01_IC_RST_RST_MSK	  0x00000001
+#define MSC01_IC_RST_RST_BIT	  MSC01_IC_RST_RST_MSK
+#define MSC01_IC_LVL_LVL_SHF	  0
+#define MSC01_IC_LVL_LVL_MSK	  0x000000ff
+#define MSC01_IC_LVL_SPUR_SHF	  16
+#define MSC01_IC_LVL_SPUR_MSK	  0x00010000
+#define MSC01_IC_LVL_SPUR_BIT	  MSC01_IC_LVL_SPUR_MSK
+#define MSC01_IC_RAMW_RIPL_SHF	  0
+#define MSC01_IC_RAMW_RIPL_MSK	  0x0000003f
+#define MSC01_IC_RAMW_DATA_SHF	  6
+#define MSC01_IC_RAMW_DATA_MSK	  0x00000fc0
+#define MSC01_IC_RAMW_ADDR_SHF	  25
+#define MSC01_IC_RAMW_ADDR_MSK	  0x7e000000
+#define MSC01_IC_RAMW_READ_SHF	  31
+#define MSC01_IC_RAMW_READ_MSK	  0x80000000
+#define MSC01_IC_RAMW_READ_BIT	  MSC01_IC_RAMW_READ_MSK
+#define MSC01_IC_OSB_OSB_SHF	  0
+#define MSC01_IC_OSB_OSB_MSK	  0x000000ff
+#define MSC01_IC_OSA_OSA_SHF	  0
+#define MSC01_IC_OSA_OSA_MSK	  0x000000ff
+#define MSC01_IC_GENA_GENA_SHF	  0
+#define MSC01_IC_GENA_GENA_MSK	  0x00000001
+#define MSC01_IC_GENA_GENA_BIT	  MSC01_IC_GENA_GENA_MSK
+#define MSC01_IC_CFG_DIS_SHF	  0
+#define MSC01_IC_CFG_DIS_MSK	  0x00000001
+#define MSC01_IC_CFG_DIS_BIT	  MSC01_IC_CFG_DIS_MSK
+#define MSC01_IC_CFG_SHFT_SHF	  8
+#define MSC01_IC_CFG_SHFT_MSK	  0x00000f00
+#define MSC01_IC_TCFG_ENA_SHF	  0
+#define MSC01_IC_TCFG_ENA_MSK	  0x00000001
+#define MSC01_IC_TCFG_ENA_BIT	  MSC01_IC_TCFG_ENA_MSK
+#define MSC01_IC_TCFG_INT_SHF	  8
+#define MSC01_IC_TCFG_INT_MSK	  0x00000100
+#define MSC01_IC_TCFG_INT_BIT	  MSC01_IC_TCFG_INT_MSK
+#define MSC01_IC_TCFG_EDGE_SHF	  16
+#define MSC01_IC_TCFG_EDGE_MSK	  0x00010000
+#define MSC01_IC_TCFG_EDGE_BIT	  MSC01_IC_TCFG_EDGE_MSK
+#define MSC01_IC_SUP_PRI_SHF	  0
+#define MSC01_IC_SUP_PRI_MSK	  0x00000007
+#define MSC01_IC_SUP_EDGE_SHF	  8
+#define MSC01_IC_SUP_EDGE_MSK	  0x00000100
+#define MSC01_IC_SUP_EDGE_BIT	  MSC01_IC_SUP_EDGE_MSK
+#define MSC01_IC_SUP_STEP	  8
+
+/*
+ * MIPS System controller interrupt register base.
+ *
+ */
+
+/*****************************************************************************
+ * Absolute register addresses
+ *****************************************************************************/
+
+#define MSC01_IC_RST	 (MSC01_IC_REG_BASE + MSC01_IC_RST_OFS)
+#define MSC01_IC_ENAL	 (MSC01_IC_REG_BASE + MSC01_IC_ENAL_OFS)
+#define MSC01_IC_ENAH	 (MSC01_IC_REG_BASE + MSC01_IC_ENAH_OFS)
+#define MSC01_IC_DISL	 (MSC01_IC_REG_BASE + MSC01_IC_DISL_OFS)
+#define MSC01_IC_DISH	 (MSC01_IC_REG_BASE + MSC01_IC_DISH_OFS)
+#define MSC01_IC_ISBL	 (MSC01_IC_REG_BASE + MSC01_IC_ISBL_OFS)
+#define MSC01_IC_ISBH	 (MSC01_IC_REG_BASE + MSC01_IC_ISBH_OFS)
+#define MSC01_IC_ISAL	 (MSC01_IC_REG_BASE + MSC01_IC_ISAL_OFS)
+#define MSC01_IC_ISAH	 (MSC01_IC_REG_BASE + MSC01_IC_ISAH_OFS)
+#define MSC01_IC_LVL	 (MSC01_IC_REG_BASE + MSC01_IC_LVL_OFS)
+#define MSC01_IC_RAMW	 (MSC01_IC_REG_BASE + MSC01_IC_RAMW_OFS)
+#define MSC01_IC_OSB	 (MSC01_IC_REG_BASE + MSC01_IC_OSB_OFS)
+#define MSC01_IC_OSA	 (MSC01_IC_REG_BASE + MSC01_IC_OSA_OFS)
+#define MSC01_IC_GENA	 (MSC01_IC_REG_BASE + MSC01_IC_GENA_OFS)
+#define MSC01_IC_BASE	 (MSC01_IC_REG_BASE + MSC01_IC_BASE_OFS)
+#define MSC01_IC_VEC	 (MSC01_IC_REG_BASE + MSC01_IC_VEC_OFS)
+#define MSC01_IC_EOI	 (MSC01_IC_REG_BASE + MSC01_IC_EOI_OFS)
+#define MSC01_IC_CFG	 (MSC01_IC_REG_BASE + MSC01_IC_CFG_OFS)
+#define MSC01_IC_TRLD	 (MSC01_IC_REG_BASE + MSC01_IC_TRLD_OFS)
+#define MSC01_IC_TVAL	 (MSC01_IC_REG_BASE + MSC01_IC_TVAL_OFS)
+#define MSC01_IC_TCFG	 (MSC01_IC_REG_BASE + MSC01_IC_TCFG_OFS)
+#define MSC01_IC_SUP	 (MSC01_IC_REG_BASE + MSC01_IC_SUP_OFS)
+#define MSC01_IC_ENA	 (MSC01_IC_REG_BASE + MSC01_IC_ENA_OFS)
+#define MSC01_IC_DIS	 (MSC01_IC_REG_BASE + MSC01_IC_DIS_OFS)
+#define MSC01_IC_ISB	 (MSC01_IC_REG_BASE + MSC01_IC_ISB_OFS)
+#define MSC01_IC_ISA	 (MSC01_IC_REG_BASE + MSC01_IC_ISA_OFS)
+
+/*
+ * Soc-it interrupts are configurable.
+ * Every board describes its IRQ mapping with this table.
+ */
+typedef struct msc_irqmap {
+	int	im_irq;
+	int	im_type;
+	int	im_lvl;
+} msc_irqmap_t;
+
+/* im_type */
+#define MSC01_IRQ_LEVEL		0
+#define MSC01_IRQ_EDGE		1
+
+extern void __init init_msc_irqs(unsigned long icubase, unsigned int base, msc_irqmap_t *imp, int nirq);
+extern void ll_msc_irq(void);
+
+#endif /* __ASM_MIPS_BOARDS_MSC01_IC_H */
diff --git a/arch/mips/include/asm/octeon/cvmx-address.h b/arch/mips/include/asm/octeon/cvmx-address.h
new file mode 100644
index 000000000..5df5c90f6
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-address.h
@@ -0,0 +1,341 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2009 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/**
+ * Typedefs and defines for working with Octeon physical addresses.
+ *
+ */
+#ifndef __CVMX_ADDRESS_H__
+#define __CVMX_ADDRESS_H__
+
+#if 0
+typedef enum {
+	CVMX_MIPS_SPACE_XKSEG = 3LL,
+	CVMX_MIPS_SPACE_XKPHYS = 2LL,
+	CVMX_MIPS_SPACE_XSSEG = 1LL,
+	CVMX_MIPS_SPACE_XUSEG = 0LL
+} cvmx_mips_space_t;
+#endif
+
+typedef enum {
+	CVMX_MIPS_XKSEG_SPACE_KSEG0 = 0LL,
+	CVMX_MIPS_XKSEG_SPACE_KSEG1 = 1LL,
+	CVMX_MIPS_XKSEG_SPACE_SSEG = 2LL,
+	CVMX_MIPS_XKSEG_SPACE_KSEG3 = 3LL
+} cvmx_mips_xkseg_space_t;
+
+/* decodes <14:13> of a kseg3 window address */
+typedef enum {
+	CVMX_ADD_WIN_SCR = 0L,
+	/* see cvmx_add_win_dma_dec_t for further decode */
+	CVMX_ADD_WIN_DMA = 1L,
+	CVMX_ADD_WIN_UNUSED = 2L,
+	CVMX_ADD_WIN_UNUSED2 = 3L
+} cvmx_add_win_dec_t;
+
+/* decode within DMA space */
+typedef enum {
+	/*
+	 * Add store data to the write buffer entry, allocating it if
+	 * necessary.
+	 */
+	CVMX_ADD_WIN_DMA_ADD = 0L,
+	/* send out the write buffer entry to DRAM */
+	CVMX_ADD_WIN_DMA_SENDMEM = 1L,
+	/* store data must be normal DRAM memory space address in this case */
+	/* send out the write buffer entry as an IOBDMA command */
+	CVMX_ADD_WIN_DMA_SENDDMA = 2L,
+	/* see CVMX_ADD_WIN_DMA_SEND_DEC for data contents */
+	/* send out the write buffer entry as an IO write */
+	CVMX_ADD_WIN_DMA_SENDIO = 3L,
+	/* store data must be normal IO space address in this case */
+	/* send out a single-tick command on the NCB bus */
+	CVMX_ADD_WIN_DMA_SENDSINGLE = 4L,
+	/* no write buffer data needed/used */
+} cvmx_add_win_dma_dec_t;
+
+/*
+ *   Physical Address Decode
+ *
+ * Octeon-I HW never interprets this X (<39:36> reserved
+ * for future expansion), software should set to 0.
+ *
+ *  - 0x0 XXX0 0000 0000 to	 DRAM	      Cached
+ *  - 0x0 XXX0 0FFF FFFF
+ *
+ *  - 0x0 XXX0 1000 0000 to	 Boot Bus     Uncached	(Converted to 0x1 00X0 1000 0000
+ *  - 0x0 XXX0 1FFF FFFF	 + EJTAG			   to 0x1 00X0 1FFF FFFF)
+ *
+ *  - 0x0 XXX0 2000 0000 to	 DRAM	      Cached
+ *  - 0x0 XXXF FFFF FFFF
+ *
+ *  - 0x1 00X0 0000 0000 to	 Boot Bus     Uncached
+ *  - 0x1 00XF FFFF FFFF
+ *
+ *  - 0x1 01X0 0000 0000 to	 Other NCB    Uncached
+ *  - 0x1 FFXF FFFF FFFF	 devices
+ *
+ * Decode of all Octeon addresses
+ */
+typedef union {
+
+	uint64_t u64;
+#ifdef __BIG_ENDIAN_BITFIELD
+	/* mapped or unmapped virtual address */
+	struct {
+		uint64_t R:2;
+		uint64_t offset:62;
+	} sva;
+
+	/* mapped USEG virtual addresses (typically) */
+	struct {
+		uint64_t zeroes:33;
+		uint64_t offset:31;
+	} suseg;
+
+	/* mapped or unmapped virtual address */
+	struct {
+		uint64_t ones:33;
+		uint64_t sp:2;
+		uint64_t offset:29;
+	} sxkseg;
+
+	/*
+	 * physical address accessed through xkphys unmapped virtual
+	 * address.
+	 */
+	struct {
+		uint64_t R:2;	/* CVMX_MIPS_SPACE_XKPHYS in this case */
+		uint64_t cca:3; /* ignored by octeon */
+		uint64_t mbz:10;
+		uint64_t pa:49; /* physical address */
+	} sxkphys;
+
+	/* physical address */
+	struct {
+		uint64_t mbz:15;
+		/* if set, the address is uncached and resides on MCB bus */
+		uint64_t is_io:1;
+		/*
+		 * the hardware ignores this field when is_io==0, else
+		 * device ID.
+		 */
+		uint64_t did:8;
+		/* the hardware ignores <39:36> in Octeon I */
+		uint64_t unaddr:4;
+		uint64_t offset:36;
+	} sphys;
+
+	/* physical mem address */
+	struct {
+		/* technically, <47:40> are dont-cares */
+		uint64_t zeroes:24;
+		/* the hardware ignores <39:36> in Octeon I */
+		uint64_t unaddr:4;
+		uint64_t offset:36;
+	} smem;
+
+	/* physical IO address */
+	struct {
+		uint64_t mem_region:2;
+		uint64_t mbz:13;
+		/* 1 in this case */
+		uint64_t is_io:1;
+		/*
+		 * The hardware ignores this field when is_io==0, else
+		 * device ID.
+		 */
+		uint64_t did:8;
+		/* the hardware ignores <39:36> in Octeon I */
+		uint64_t unaddr:4;
+		uint64_t offset:36;
+	} sio;
+
+	/*
+	 * Scratchpad virtual address - accessed through a window at
+	 * the end of kseg3
+	 */
+	struct {
+		uint64_t ones:49;
+		/* CVMX_ADD_WIN_SCR (0) in this case */
+		cvmx_add_win_dec_t csrdec:2;
+		uint64_t addr:13;
+	} sscr;
+
+	/* there should only be stores to IOBDMA space, no loads */
+	/*
+	 * IOBDMA virtual address - accessed through a window at the
+	 * end of kseg3
+	 */
+	struct {
+		uint64_t ones:49;
+		uint64_t csrdec:2;	/* CVMX_ADD_WIN_DMA (1) in this case */
+		uint64_t unused2:3;
+		uint64_t type:3;
+		uint64_t addr:7;
+	} sdma;
+
+	struct {
+		uint64_t didspace:24;
+		uint64_t unused:40;
+	} sfilldidspace;
+#else
+	struct {
+		uint64_t offset:62;
+		uint64_t R:2;
+	} sva;
+
+	struct {
+		uint64_t offset:31;
+		uint64_t zeroes:33;
+	} suseg;
+
+	struct {
+		uint64_t offset:29;
+		uint64_t sp:2;
+		uint64_t ones:33;
+	} sxkseg;
+
+	struct {
+		uint64_t pa:49;
+		uint64_t mbz:10;
+		uint64_t cca:3;
+		uint64_t R:2;
+	} sxkphys;
+
+	struct {
+		uint64_t offset:36;
+		uint64_t unaddr:4;
+		uint64_t did:8;
+		uint64_t is_io:1;
+		uint64_t mbz:15;
+	} sphys;
+
+	struct {
+		uint64_t offset:36;
+		uint64_t unaddr:4;
+		uint64_t zeroes:24;
+	} smem;
+
+	struct {
+		uint64_t offset:36;
+		uint64_t unaddr:4;
+		uint64_t did:8;
+		uint64_t is_io:1;
+		uint64_t mbz:13;
+		uint64_t mem_region:2;
+	} sio;
+
+	struct {
+		uint64_t addr:13;
+		cvmx_add_win_dec_t csrdec:2;
+		uint64_t ones:49;
+	} sscr;
+
+	struct {
+		uint64_t addr:7;
+		uint64_t type:3;
+		uint64_t unused2:3;
+		uint64_t csrdec:2;
+		uint64_t ones:49;
+	} sdma;
+
+	struct {
+		uint64_t unused:40;
+		uint64_t didspace:24;
+	} sfilldidspace;
+#endif
+
+} cvmx_addr_t;
+
+/* These macros for used by 32 bit applications */
+
+#define CVMX_MIPS32_SPACE_KSEG0 1l
+#define CVMX_ADD_SEG32(segment, add) \
+	(((int32_t)segment << 31) | (int32_t)(add))
+
+/*
+ * Currently all IOs are performed using XKPHYS addressing. Linux uses
+ * the CvmMemCtl register to enable XKPHYS addressing to IO space from
+ * user mode.  Future OSes may need to change the upper bits of IO
+ * addresses. The following define controls the upper two bits for all
+ * IO addresses generated by the simple executive library.
+ */
+#define CVMX_IO_SEG CVMX_MIPS_SPACE_XKPHYS
+
+/* These macros simplify the process of creating common IO addresses */
+#define CVMX_ADD_SEG(segment, add) ((((uint64_t)segment) << 62) | (add))
+#ifndef CVMX_ADD_IO_SEG
+#define CVMX_ADD_IO_SEG(add) CVMX_ADD_SEG(CVMX_IO_SEG, (add))
+#endif
+#define CVMX_ADDR_DIDSPACE(did) (((CVMX_IO_SEG) << 22) | ((1ULL) << 8) | (did))
+#define CVMX_ADDR_DID(did) (CVMX_ADDR_DIDSPACE(did) << 40)
+#define CVMX_FULL_DID(did, subdid) (((did) << 3) | (subdid))
+
+  /* from include/ncb_rsl_id.v */
+#define CVMX_OCT_DID_MIS 0ULL	/* misc stuff */
+#define CVMX_OCT_DID_GMX0 1ULL
+#define CVMX_OCT_DID_GMX1 2ULL
+#define CVMX_OCT_DID_PCI 3ULL
+#define CVMX_OCT_DID_KEY 4ULL
+#define CVMX_OCT_DID_FPA 5ULL
+#define CVMX_OCT_DID_DFA 6ULL
+#define CVMX_OCT_DID_ZIP 7ULL
+#define CVMX_OCT_DID_RNG 8ULL
+#define CVMX_OCT_DID_IPD 9ULL
+#define CVMX_OCT_DID_PKT 10ULL
+#define CVMX_OCT_DID_TIM 11ULL
+#define CVMX_OCT_DID_TAG 12ULL
+  /* the rest are not on the IO bus */
+#define CVMX_OCT_DID_L2C 16ULL
+#define CVMX_OCT_DID_LMC 17ULL
+#define CVMX_OCT_DID_SPX0 18ULL
+#define CVMX_OCT_DID_SPX1 19ULL
+#define CVMX_OCT_DID_PIP 20ULL
+#define CVMX_OCT_DID_ASX0 22ULL
+#define CVMX_OCT_DID_ASX1 23ULL
+#define CVMX_OCT_DID_IOB 30ULL
+
+#define CVMX_OCT_DID_PKT_SEND	    CVMX_FULL_DID(CVMX_OCT_DID_PKT, 2ULL)
+#define CVMX_OCT_DID_TAG_SWTAG	    CVMX_FULL_DID(CVMX_OCT_DID_TAG, 0ULL)
+#define CVMX_OCT_DID_TAG_TAG1	    CVMX_FULL_DID(CVMX_OCT_DID_TAG, 1ULL)
+#define CVMX_OCT_DID_TAG_TAG2	    CVMX_FULL_DID(CVMX_OCT_DID_TAG, 2ULL)
+#define CVMX_OCT_DID_TAG_TAG3	    CVMX_FULL_DID(CVMX_OCT_DID_TAG, 3ULL)
+#define CVMX_OCT_DID_TAG_NULL_RD    CVMX_FULL_DID(CVMX_OCT_DID_TAG, 4ULL)
+#define CVMX_OCT_DID_TAG_CSR	    CVMX_FULL_DID(CVMX_OCT_DID_TAG, 7ULL)
+#define CVMX_OCT_DID_FAU_FAI	    CVMX_FULL_DID(CVMX_OCT_DID_IOB, 0ULL)
+#define CVMX_OCT_DID_TIM_CSR	    CVMX_FULL_DID(CVMX_OCT_DID_TIM, 0ULL)
+#define CVMX_OCT_DID_KEY_RW	    CVMX_FULL_DID(CVMX_OCT_DID_KEY, 0ULL)
+#define CVMX_OCT_DID_PCI_6	    CVMX_FULL_DID(CVMX_OCT_DID_PCI, 6ULL)
+#define CVMX_OCT_DID_MIS_BOO	    CVMX_FULL_DID(CVMX_OCT_DID_MIS, 0ULL)
+#define CVMX_OCT_DID_PCI_RML	    CVMX_FULL_DID(CVMX_OCT_DID_PCI, 0ULL)
+#define CVMX_OCT_DID_IPD_CSR	    CVMX_FULL_DID(CVMX_OCT_DID_IPD, 7ULL)
+#define CVMX_OCT_DID_DFA_CSR	    CVMX_FULL_DID(CVMX_OCT_DID_DFA, 7ULL)
+#define CVMX_OCT_DID_MIS_CSR	    CVMX_FULL_DID(CVMX_OCT_DID_MIS, 7ULL)
+#define CVMX_OCT_DID_ZIP_CSR	    CVMX_FULL_DID(CVMX_OCT_DID_ZIP, 0ULL)
+
+#endif /* __CVMX_ADDRESS_H__ */
diff --git a/arch/mips/include/asm/octeon/cvmx-agl-defs.h b/arch/mips/include/asm/octeon/cvmx-agl-defs.h
new file mode 100644
index 000000000..3635ab384
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-agl-defs.h
@@ -0,0 +1,1759 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2012 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_AGL_DEFS_H__
+#define __CVMX_AGL_DEFS_H__
+
+#define CVMX_AGL_GMX_BAD_REG (CVMX_ADD_IO_SEG(0x00011800E0000518ull))
+#define CVMX_AGL_GMX_BIST (CVMX_ADD_IO_SEG(0x00011800E0000400ull))
+#define CVMX_AGL_GMX_DRV_CTL (CVMX_ADD_IO_SEG(0x00011800E00007F0ull))
+#define CVMX_AGL_GMX_INF_MODE (CVMX_ADD_IO_SEG(0x00011800E00007F8ull))
+#define CVMX_AGL_GMX_PRTX_CFG(offset) (CVMX_ADD_IO_SEG(0x00011800E0000010ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RXX_ADR_CAM0(offset) (CVMX_ADD_IO_SEG(0x00011800E0000180ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RXX_ADR_CAM1(offset) (CVMX_ADD_IO_SEG(0x00011800E0000188ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RXX_ADR_CAM2(offset) (CVMX_ADD_IO_SEG(0x00011800E0000190ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RXX_ADR_CAM3(offset) (CVMX_ADD_IO_SEG(0x00011800E0000198ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RXX_ADR_CAM4(offset) (CVMX_ADD_IO_SEG(0x00011800E00001A0ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RXX_ADR_CAM5(offset) (CVMX_ADD_IO_SEG(0x00011800E00001A8ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RXX_ADR_CAM_EN(offset) (CVMX_ADD_IO_SEG(0x00011800E0000108ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RXX_ADR_CTL(offset) (CVMX_ADD_IO_SEG(0x00011800E0000100ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RXX_DECISION(offset) (CVMX_ADD_IO_SEG(0x00011800E0000040ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RXX_FRM_CHK(offset) (CVMX_ADD_IO_SEG(0x00011800E0000020ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RXX_FRM_CTL(offset) (CVMX_ADD_IO_SEG(0x00011800E0000018ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RXX_FRM_MAX(offset) (CVMX_ADD_IO_SEG(0x00011800E0000030ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RXX_FRM_MIN(offset) (CVMX_ADD_IO_SEG(0x00011800E0000028ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RXX_IFG(offset) (CVMX_ADD_IO_SEG(0x00011800E0000058ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RXX_INT_EN(offset) (CVMX_ADD_IO_SEG(0x00011800E0000008ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RXX_INT_REG(offset) (CVMX_ADD_IO_SEG(0x00011800E0000000ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RXX_JABBER(offset) (CVMX_ADD_IO_SEG(0x00011800E0000038ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RXX_PAUSE_DROP_TIME(offset) (CVMX_ADD_IO_SEG(0x00011800E0000068ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RXX_RX_INBND(offset) (CVMX_ADD_IO_SEG(0x00011800E0000060ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RXX_STATS_CTL(offset) (CVMX_ADD_IO_SEG(0x00011800E0000050ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RXX_STATS_OCTS(offset) (CVMX_ADD_IO_SEG(0x00011800E0000088ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RXX_STATS_OCTS_CTL(offset) (CVMX_ADD_IO_SEG(0x00011800E0000098ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RXX_STATS_OCTS_DMAC(offset) (CVMX_ADD_IO_SEG(0x00011800E00000A8ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RXX_STATS_OCTS_DRP(offset) (CVMX_ADD_IO_SEG(0x00011800E00000B8ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RXX_STATS_PKTS(offset) (CVMX_ADD_IO_SEG(0x00011800E0000080ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RXX_STATS_PKTS_BAD(offset) (CVMX_ADD_IO_SEG(0x00011800E00000C0ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RXX_STATS_PKTS_CTL(offset) (CVMX_ADD_IO_SEG(0x00011800E0000090ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RXX_STATS_PKTS_DMAC(offset) (CVMX_ADD_IO_SEG(0x00011800E00000A0ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RXX_STATS_PKTS_DRP(offset) (CVMX_ADD_IO_SEG(0x00011800E00000B0ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RXX_UDD_SKP(offset) (CVMX_ADD_IO_SEG(0x00011800E0000048ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_RX_BP_DROPX(offset) (CVMX_ADD_IO_SEG(0x00011800E0000420ull) + ((offset) & 1) * 8)
+#define CVMX_AGL_GMX_RX_BP_OFFX(offset) (CVMX_ADD_IO_SEG(0x00011800E0000460ull) + ((offset) & 1) * 8)
+#define CVMX_AGL_GMX_RX_BP_ONX(offset) (CVMX_ADD_IO_SEG(0x00011800E0000440ull) + ((offset) & 1) * 8)
+#define CVMX_AGL_GMX_RX_PRT_INFO (CVMX_ADD_IO_SEG(0x00011800E00004E8ull))
+#define CVMX_AGL_GMX_RX_TX_STATUS (CVMX_ADD_IO_SEG(0x00011800E00007E8ull))
+#define CVMX_AGL_GMX_SMACX(offset) (CVMX_ADD_IO_SEG(0x00011800E0000230ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_STAT_BP (CVMX_ADD_IO_SEG(0x00011800E0000520ull))
+#define CVMX_AGL_GMX_TXX_APPEND(offset) (CVMX_ADD_IO_SEG(0x00011800E0000218ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_TXX_CLK(offset) (CVMX_ADD_IO_SEG(0x00011800E0000208ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_TXX_CTL(offset) (CVMX_ADD_IO_SEG(0x00011800E0000270ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_TXX_MIN_PKT(offset) (CVMX_ADD_IO_SEG(0x00011800E0000240ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_TXX_PAUSE_PKT_INTERVAL(offset) (CVMX_ADD_IO_SEG(0x00011800E0000248ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_TXX_PAUSE_PKT_TIME(offset) (CVMX_ADD_IO_SEG(0x00011800E0000238ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_TXX_PAUSE_TOGO(offset) (CVMX_ADD_IO_SEG(0x00011800E0000258ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_TXX_PAUSE_ZERO(offset) (CVMX_ADD_IO_SEG(0x00011800E0000260ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_TXX_SOFT_PAUSE(offset) (CVMX_ADD_IO_SEG(0x00011800E0000250ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_TXX_STAT0(offset) (CVMX_ADD_IO_SEG(0x00011800E0000280ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_TXX_STAT1(offset) (CVMX_ADD_IO_SEG(0x00011800E0000288ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_TXX_STAT2(offset) (CVMX_ADD_IO_SEG(0x00011800E0000290ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_TXX_STAT3(offset) (CVMX_ADD_IO_SEG(0x00011800E0000298ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_TXX_STAT4(offset) (CVMX_ADD_IO_SEG(0x00011800E00002A0ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_TXX_STAT5(offset) (CVMX_ADD_IO_SEG(0x00011800E00002A8ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_TXX_STAT6(offset) (CVMX_ADD_IO_SEG(0x00011800E00002B0ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_TXX_STAT7(offset) (CVMX_ADD_IO_SEG(0x00011800E00002B8ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_TXX_STAT8(offset) (CVMX_ADD_IO_SEG(0x00011800E00002C0ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_TXX_STAT9(offset) (CVMX_ADD_IO_SEG(0x00011800E00002C8ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_TXX_STATS_CTL(offset) (CVMX_ADD_IO_SEG(0x00011800E0000268ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_TXX_THRESH(offset) (CVMX_ADD_IO_SEG(0x00011800E0000210ull) + ((offset) & 1) * 2048)
+#define CVMX_AGL_GMX_TX_BP (CVMX_ADD_IO_SEG(0x00011800E00004D0ull))
+#define CVMX_AGL_GMX_TX_COL_ATTEMPT (CVMX_ADD_IO_SEG(0x00011800E0000498ull))
+#define CVMX_AGL_GMX_TX_IFG (CVMX_ADD_IO_SEG(0x00011800E0000488ull))
+#define CVMX_AGL_GMX_TX_INT_EN (CVMX_ADD_IO_SEG(0x00011800E0000508ull))
+#define CVMX_AGL_GMX_TX_INT_REG (CVMX_ADD_IO_SEG(0x00011800E0000500ull))
+#define CVMX_AGL_GMX_TX_JAM (CVMX_ADD_IO_SEG(0x00011800E0000490ull))
+#define CVMX_AGL_GMX_TX_LFSR (CVMX_ADD_IO_SEG(0x00011800E00004F8ull))
+#define CVMX_AGL_GMX_TX_OVR_BP (CVMX_ADD_IO_SEG(0x00011800E00004C8ull))
+#define CVMX_AGL_GMX_TX_PAUSE_PKT_DMAC (CVMX_ADD_IO_SEG(0x00011800E00004A0ull))
+#define CVMX_AGL_GMX_TX_PAUSE_PKT_TYPE (CVMX_ADD_IO_SEG(0x00011800E00004A8ull))
+#define CVMX_AGL_PRTX_CTL(offset) (CVMX_ADD_IO_SEG(0x00011800E0002000ull) + ((offset) & 1) * 8)
+
+union cvmx_agl_gmx_bad_reg {
+	uint64_t u64;
+	struct cvmx_agl_gmx_bad_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_38_63:26;
+		uint64_t txpsh1:1;
+		uint64_t txpop1:1;
+		uint64_t ovrflw1:1;
+		uint64_t txpsh:1;
+		uint64_t txpop:1;
+		uint64_t ovrflw:1;
+		uint64_t reserved_27_31:5;
+		uint64_t statovr:1;
+		uint64_t reserved_24_25:2;
+		uint64_t loststat:2;
+		uint64_t reserved_4_21:18;
+		uint64_t out_ovr:2;
+		uint64_t reserved_0_1:2;
+#else
+		uint64_t reserved_0_1:2;
+		uint64_t out_ovr:2;
+		uint64_t reserved_4_21:18;
+		uint64_t loststat:2;
+		uint64_t reserved_24_25:2;
+		uint64_t statovr:1;
+		uint64_t reserved_27_31:5;
+		uint64_t ovrflw:1;
+		uint64_t txpop:1;
+		uint64_t txpsh:1;
+		uint64_t ovrflw1:1;
+		uint64_t txpop1:1;
+		uint64_t txpsh1:1;
+		uint64_t reserved_38_63:26;
+#endif
+	} s;
+	struct cvmx_agl_gmx_bad_reg_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_38_63:26;
+		uint64_t txpsh1:1;
+		uint64_t txpop1:1;
+		uint64_t ovrflw1:1;
+		uint64_t txpsh:1;
+		uint64_t txpop:1;
+		uint64_t ovrflw:1;
+		uint64_t reserved_27_31:5;
+		uint64_t statovr:1;
+		uint64_t reserved_23_25:3;
+		uint64_t loststat:1;
+		uint64_t reserved_4_21:18;
+		uint64_t out_ovr:2;
+		uint64_t reserved_0_1:2;
+#else
+		uint64_t reserved_0_1:2;
+		uint64_t out_ovr:2;
+		uint64_t reserved_4_21:18;
+		uint64_t loststat:1;
+		uint64_t reserved_23_25:3;
+		uint64_t statovr:1;
+		uint64_t reserved_27_31:5;
+		uint64_t ovrflw:1;
+		uint64_t txpop:1;
+		uint64_t txpsh:1;
+		uint64_t ovrflw1:1;
+		uint64_t txpop1:1;
+		uint64_t txpsh1:1;
+		uint64_t reserved_38_63:26;
+#endif
+	} cn52xx;
+	struct cvmx_agl_gmx_bad_reg_cn56xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_35_63:29;
+		uint64_t txpsh:1;
+		uint64_t txpop:1;
+		uint64_t ovrflw:1;
+		uint64_t reserved_27_31:5;
+		uint64_t statovr:1;
+		uint64_t reserved_23_25:3;
+		uint64_t loststat:1;
+		uint64_t reserved_3_21:19;
+		uint64_t out_ovr:1;
+		uint64_t reserved_0_1:2;
+#else
+		uint64_t reserved_0_1:2;
+		uint64_t out_ovr:1;
+		uint64_t reserved_3_21:19;
+		uint64_t loststat:1;
+		uint64_t reserved_23_25:3;
+		uint64_t statovr:1;
+		uint64_t reserved_27_31:5;
+		uint64_t ovrflw:1;
+		uint64_t txpop:1;
+		uint64_t txpsh:1;
+		uint64_t reserved_35_63:29;
+#endif
+	} cn56xx;
+};
+
+union cvmx_agl_gmx_bist {
+	uint64_t u64;
+	struct cvmx_agl_gmx_bist_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_25_63:39;
+		uint64_t status:25;
+#else
+		uint64_t status:25;
+		uint64_t reserved_25_63:39;
+#endif
+	} s;
+	struct cvmx_agl_gmx_bist_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t status:10;
+#else
+		uint64_t status:10;
+		uint64_t reserved_10_63:54;
+#endif
+	} cn52xx;
+};
+
+union cvmx_agl_gmx_drv_ctl {
+	uint64_t u64;
+	struct cvmx_agl_gmx_drv_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_49_63:15;
+		uint64_t byp_en1:1;
+		uint64_t reserved_45_47:3;
+		uint64_t pctl1:5;
+		uint64_t reserved_37_39:3;
+		uint64_t nctl1:5;
+		uint64_t reserved_17_31:15;
+		uint64_t byp_en:1;
+		uint64_t reserved_13_15:3;
+		uint64_t pctl:5;
+		uint64_t reserved_5_7:3;
+		uint64_t nctl:5;
+#else
+		uint64_t nctl:5;
+		uint64_t reserved_5_7:3;
+		uint64_t pctl:5;
+		uint64_t reserved_13_15:3;
+		uint64_t byp_en:1;
+		uint64_t reserved_17_31:15;
+		uint64_t nctl1:5;
+		uint64_t reserved_37_39:3;
+		uint64_t pctl1:5;
+		uint64_t reserved_45_47:3;
+		uint64_t byp_en1:1;
+		uint64_t reserved_49_63:15;
+#endif
+	} s;
+	struct cvmx_agl_gmx_drv_ctl_cn56xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_17_63:47;
+		uint64_t byp_en:1;
+		uint64_t reserved_13_15:3;
+		uint64_t pctl:5;
+		uint64_t reserved_5_7:3;
+		uint64_t nctl:5;
+#else
+		uint64_t nctl:5;
+		uint64_t reserved_5_7:3;
+		uint64_t pctl:5;
+		uint64_t reserved_13_15:3;
+		uint64_t byp_en:1;
+		uint64_t reserved_17_63:47;
+#endif
+	} cn56xx;
+};
+
+union cvmx_agl_gmx_inf_mode {
+	uint64_t u64;
+	struct cvmx_agl_gmx_inf_mode_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t en:1;
+		uint64_t reserved_0_0:1;
+#else
+		uint64_t reserved_0_0:1;
+		uint64_t en:1;
+		uint64_t reserved_2_63:62;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_prtx_cfg {
+	uint64_t u64;
+	struct cvmx_agl_gmx_prtx_cfg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_14_63:50;
+		uint64_t tx_idle:1;
+		uint64_t rx_idle:1;
+		uint64_t reserved_9_11:3;
+		uint64_t speed_msb:1;
+		uint64_t reserved_7_7:1;
+		uint64_t burst:1;
+		uint64_t tx_en:1;
+		uint64_t rx_en:1;
+		uint64_t slottime:1;
+		uint64_t duplex:1;
+		uint64_t speed:1;
+		uint64_t en:1;
+#else
+		uint64_t en:1;
+		uint64_t speed:1;
+		uint64_t duplex:1;
+		uint64_t slottime:1;
+		uint64_t rx_en:1;
+		uint64_t tx_en:1;
+		uint64_t burst:1;
+		uint64_t reserved_7_7:1;
+		uint64_t speed_msb:1;
+		uint64_t reserved_9_11:3;
+		uint64_t rx_idle:1;
+		uint64_t tx_idle:1;
+		uint64_t reserved_14_63:50;
+#endif
+	} s;
+	struct cvmx_agl_gmx_prtx_cfg_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t tx_en:1;
+		uint64_t rx_en:1;
+		uint64_t slottime:1;
+		uint64_t duplex:1;
+		uint64_t speed:1;
+		uint64_t en:1;
+#else
+		uint64_t en:1;
+		uint64_t speed:1;
+		uint64_t duplex:1;
+		uint64_t slottime:1;
+		uint64_t rx_en:1;
+		uint64_t tx_en:1;
+		uint64_t reserved_6_63:58;
+#endif
+	} cn52xx;
+};
+
+union cvmx_agl_gmx_rxx_adr_cam0 {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rxx_adr_cam0_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t adr:64;
+#else
+		uint64_t adr:64;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_rxx_adr_cam1 {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rxx_adr_cam1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t adr:64;
+#else
+		uint64_t adr:64;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_rxx_adr_cam2 {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rxx_adr_cam2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t adr:64;
+#else
+		uint64_t adr:64;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_rxx_adr_cam3 {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rxx_adr_cam3_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t adr:64;
+#else
+		uint64_t adr:64;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_rxx_adr_cam4 {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rxx_adr_cam4_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t adr:64;
+#else
+		uint64_t adr:64;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_rxx_adr_cam5 {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rxx_adr_cam5_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t adr:64;
+#else
+		uint64_t adr:64;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_rxx_adr_cam_en {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rxx_adr_cam_en_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t en:8;
+#else
+		uint64_t en:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_rxx_adr_ctl {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rxx_adr_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t cam_mode:1;
+		uint64_t mcst:2;
+		uint64_t bcst:1;
+#else
+		uint64_t bcst:1;
+		uint64_t mcst:2;
+		uint64_t cam_mode:1;
+		uint64_t reserved_4_63:60;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_rxx_decision {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rxx_decision_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_5_63:59;
+		uint64_t cnt:5;
+#else
+		uint64_t cnt:5;
+		uint64_t reserved_5_63:59;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_rxx_frm_chk {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rxx_frm_chk_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t niberr:1;
+		uint64_t skperr:1;
+		uint64_t rcverr:1;
+		uint64_t lenerr:1;
+		uint64_t alnerr:1;
+		uint64_t fcserr:1;
+		uint64_t jabber:1;
+		uint64_t maxerr:1;
+		uint64_t carext:1;
+		uint64_t minerr:1;
+#else
+		uint64_t minerr:1;
+		uint64_t carext:1;
+		uint64_t maxerr:1;
+		uint64_t jabber:1;
+		uint64_t fcserr:1;
+		uint64_t alnerr:1;
+		uint64_t lenerr:1;
+		uint64_t rcverr:1;
+		uint64_t skperr:1;
+		uint64_t niberr:1;
+		uint64_t reserved_10_63:54;
+#endif
+	} s;
+	struct cvmx_agl_gmx_rxx_frm_chk_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_9_63:55;
+		uint64_t skperr:1;
+		uint64_t rcverr:1;
+		uint64_t lenerr:1;
+		uint64_t alnerr:1;
+		uint64_t fcserr:1;
+		uint64_t jabber:1;
+		uint64_t maxerr:1;
+		uint64_t reserved_1_1:1;
+		uint64_t minerr:1;
+#else
+		uint64_t minerr:1;
+		uint64_t reserved_1_1:1;
+		uint64_t maxerr:1;
+		uint64_t jabber:1;
+		uint64_t fcserr:1;
+		uint64_t alnerr:1;
+		uint64_t lenerr:1;
+		uint64_t rcverr:1;
+		uint64_t skperr:1;
+		uint64_t reserved_9_63:55;
+#endif
+	} cn52xx;
+};
+
+union cvmx_agl_gmx_rxx_frm_ctl {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rxx_frm_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_13_63:51;
+		uint64_t ptp_mode:1;
+		uint64_t reserved_11_11:1;
+		uint64_t null_dis:1;
+		uint64_t pre_align:1;
+		uint64_t pad_len:1;
+		uint64_t vlan_len:1;
+		uint64_t pre_free:1;
+		uint64_t ctl_smac:1;
+		uint64_t ctl_mcst:1;
+		uint64_t ctl_bck:1;
+		uint64_t ctl_drp:1;
+		uint64_t pre_strp:1;
+		uint64_t pre_chk:1;
+#else
+		uint64_t pre_chk:1;
+		uint64_t pre_strp:1;
+		uint64_t ctl_drp:1;
+		uint64_t ctl_bck:1;
+		uint64_t ctl_mcst:1;
+		uint64_t ctl_smac:1;
+		uint64_t pre_free:1;
+		uint64_t vlan_len:1;
+		uint64_t pad_len:1;
+		uint64_t pre_align:1;
+		uint64_t null_dis:1;
+		uint64_t reserved_11_11:1;
+		uint64_t ptp_mode:1;
+		uint64_t reserved_13_63:51;
+#endif
+	} s;
+	struct cvmx_agl_gmx_rxx_frm_ctl_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t pre_align:1;
+		uint64_t pad_len:1;
+		uint64_t vlan_len:1;
+		uint64_t pre_free:1;
+		uint64_t ctl_smac:1;
+		uint64_t ctl_mcst:1;
+		uint64_t ctl_bck:1;
+		uint64_t ctl_drp:1;
+		uint64_t pre_strp:1;
+		uint64_t pre_chk:1;
+#else
+		uint64_t pre_chk:1;
+		uint64_t pre_strp:1;
+		uint64_t ctl_drp:1;
+		uint64_t ctl_bck:1;
+		uint64_t ctl_mcst:1;
+		uint64_t ctl_smac:1;
+		uint64_t pre_free:1;
+		uint64_t vlan_len:1;
+		uint64_t pad_len:1;
+		uint64_t pre_align:1;
+		uint64_t reserved_10_63:54;
+#endif
+	} cn52xx;
+};
+
+union cvmx_agl_gmx_rxx_frm_max {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rxx_frm_max_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t len:16;
+#else
+		uint64_t len:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_rxx_frm_min {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rxx_frm_min_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t len:16;
+#else
+		uint64_t len:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_rxx_ifg {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rxx_ifg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t ifg:4;
+#else
+		uint64_t ifg:4;
+		uint64_t reserved_4_63:60;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_rxx_int_en {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rxx_int_en_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t pause_drp:1;
+		uint64_t phy_dupx:1;
+		uint64_t phy_spd:1;
+		uint64_t phy_link:1;
+		uint64_t ifgerr:1;
+		uint64_t coldet:1;
+		uint64_t falerr:1;
+		uint64_t rsverr:1;
+		uint64_t pcterr:1;
+		uint64_t ovrerr:1;
+		uint64_t niberr:1;
+		uint64_t skperr:1;
+		uint64_t rcverr:1;
+		uint64_t lenerr:1;
+		uint64_t alnerr:1;
+		uint64_t fcserr:1;
+		uint64_t jabber:1;
+		uint64_t maxerr:1;
+		uint64_t carext:1;
+		uint64_t minerr:1;
+#else
+		uint64_t minerr:1;
+		uint64_t carext:1;
+		uint64_t maxerr:1;
+		uint64_t jabber:1;
+		uint64_t fcserr:1;
+		uint64_t alnerr:1;
+		uint64_t lenerr:1;
+		uint64_t rcverr:1;
+		uint64_t skperr:1;
+		uint64_t niberr:1;
+		uint64_t ovrerr:1;
+		uint64_t pcterr:1;
+		uint64_t rsverr:1;
+		uint64_t falerr:1;
+		uint64_t coldet:1;
+		uint64_t ifgerr:1;
+		uint64_t phy_link:1;
+		uint64_t phy_spd:1;
+		uint64_t phy_dupx:1;
+		uint64_t pause_drp:1;
+		uint64_t reserved_20_63:44;
+#endif
+	} s;
+	struct cvmx_agl_gmx_rxx_int_en_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t pause_drp:1;
+		uint64_t reserved_16_18:3;
+		uint64_t ifgerr:1;
+		uint64_t coldet:1;
+		uint64_t falerr:1;
+		uint64_t rsverr:1;
+		uint64_t pcterr:1;
+		uint64_t ovrerr:1;
+		uint64_t reserved_9_9:1;
+		uint64_t skperr:1;
+		uint64_t rcverr:1;
+		uint64_t lenerr:1;
+		uint64_t alnerr:1;
+		uint64_t fcserr:1;
+		uint64_t jabber:1;
+		uint64_t maxerr:1;
+		uint64_t reserved_1_1:1;
+		uint64_t minerr:1;
+#else
+		uint64_t minerr:1;
+		uint64_t reserved_1_1:1;
+		uint64_t maxerr:1;
+		uint64_t jabber:1;
+		uint64_t fcserr:1;
+		uint64_t alnerr:1;
+		uint64_t lenerr:1;
+		uint64_t rcverr:1;
+		uint64_t skperr:1;
+		uint64_t reserved_9_9:1;
+		uint64_t ovrerr:1;
+		uint64_t pcterr:1;
+		uint64_t rsverr:1;
+		uint64_t falerr:1;
+		uint64_t coldet:1;
+		uint64_t ifgerr:1;
+		uint64_t reserved_16_18:3;
+		uint64_t pause_drp:1;
+		uint64_t reserved_20_63:44;
+#endif
+	} cn52xx;
+};
+
+union cvmx_agl_gmx_rxx_int_reg {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rxx_int_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t pause_drp:1;
+		uint64_t phy_dupx:1;
+		uint64_t phy_spd:1;
+		uint64_t phy_link:1;
+		uint64_t ifgerr:1;
+		uint64_t coldet:1;
+		uint64_t falerr:1;
+		uint64_t rsverr:1;
+		uint64_t pcterr:1;
+		uint64_t ovrerr:1;
+		uint64_t niberr:1;
+		uint64_t skperr:1;
+		uint64_t rcverr:1;
+		uint64_t lenerr:1;
+		uint64_t alnerr:1;
+		uint64_t fcserr:1;
+		uint64_t jabber:1;
+		uint64_t maxerr:1;
+		uint64_t carext:1;
+		uint64_t minerr:1;
+#else
+		uint64_t minerr:1;
+		uint64_t carext:1;
+		uint64_t maxerr:1;
+		uint64_t jabber:1;
+		uint64_t fcserr:1;
+		uint64_t alnerr:1;
+		uint64_t lenerr:1;
+		uint64_t rcverr:1;
+		uint64_t skperr:1;
+		uint64_t niberr:1;
+		uint64_t ovrerr:1;
+		uint64_t pcterr:1;
+		uint64_t rsverr:1;
+		uint64_t falerr:1;
+		uint64_t coldet:1;
+		uint64_t ifgerr:1;
+		uint64_t phy_link:1;
+		uint64_t phy_spd:1;
+		uint64_t phy_dupx:1;
+		uint64_t pause_drp:1;
+		uint64_t reserved_20_63:44;
+#endif
+	} s;
+	struct cvmx_agl_gmx_rxx_int_reg_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t pause_drp:1;
+		uint64_t reserved_16_18:3;
+		uint64_t ifgerr:1;
+		uint64_t coldet:1;
+		uint64_t falerr:1;
+		uint64_t rsverr:1;
+		uint64_t pcterr:1;
+		uint64_t ovrerr:1;
+		uint64_t reserved_9_9:1;
+		uint64_t skperr:1;
+		uint64_t rcverr:1;
+		uint64_t lenerr:1;
+		uint64_t alnerr:1;
+		uint64_t fcserr:1;
+		uint64_t jabber:1;
+		uint64_t maxerr:1;
+		uint64_t reserved_1_1:1;
+		uint64_t minerr:1;
+#else
+		uint64_t minerr:1;
+		uint64_t reserved_1_1:1;
+		uint64_t maxerr:1;
+		uint64_t jabber:1;
+		uint64_t fcserr:1;
+		uint64_t alnerr:1;
+		uint64_t lenerr:1;
+		uint64_t rcverr:1;
+		uint64_t skperr:1;
+		uint64_t reserved_9_9:1;
+		uint64_t ovrerr:1;
+		uint64_t pcterr:1;
+		uint64_t rsverr:1;
+		uint64_t falerr:1;
+		uint64_t coldet:1;
+		uint64_t ifgerr:1;
+		uint64_t reserved_16_18:3;
+		uint64_t pause_drp:1;
+		uint64_t reserved_20_63:44;
+#endif
+	} cn52xx;
+};
+
+union cvmx_agl_gmx_rxx_jabber {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rxx_jabber_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t cnt:16;
+#else
+		uint64_t cnt:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_rxx_pause_drop_time {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rxx_pause_drop_time_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t status:16;
+#else
+		uint64_t status:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_rxx_rx_inbnd {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rxx_rx_inbnd_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t duplex:1;
+		uint64_t speed:2;
+		uint64_t status:1;
+#else
+		uint64_t status:1;
+		uint64_t speed:2;
+		uint64_t duplex:1;
+		uint64_t reserved_4_63:60;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_rxx_stats_ctl {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rxx_stats_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t rd_clr:1;
+#else
+		uint64_t rd_clr:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_rxx_stats_octs {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rxx_stats_octs_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t cnt:48;
+#else
+		uint64_t cnt:48;
+		uint64_t reserved_48_63:16;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_rxx_stats_octs_ctl {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rxx_stats_octs_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t cnt:48;
+#else
+		uint64_t cnt:48;
+		uint64_t reserved_48_63:16;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_rxx_stats_octs_dmac {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rxx_stats_octs_dmac_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t cnt:48;
+#else
+		uint64_t cnt:48;
+		uint64_t reserved_48_63:16;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_rxx_stats_octs_drp {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rxx_stats_octs_drp_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t cnt:48;
+#else
+		uint64_t cnt:48;
+		uint64_t reserved_48_63:16;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_rxx_stats_pkts {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rxx_stats_pkts_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t cnt:32;
+#else
+		uint64_t cnt:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_rxx_stats_pkts_bad {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rxx_stats_pkts_bad_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t cnt:32;
+#else
+		uint64_t cnt:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_rxx_stats_pkts_ctl {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rxx_stats_pkts_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t cnt:32;
+#else
+		uint64_t cnt:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_rxx_stats_pkts_dmac {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rxx_stats_pkts_dmac_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t cnt:32;
+#else
+		uint64_t cnt:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_rxx_stats_pkts_drp {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rxx_stats_pkts_drp_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t cnt:32;
+#else
+		uint64_t cnt:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_rxx_udd_skp {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rxx_udd_skp_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_9_63:55;
+		uint64_t fcssel:1;
+		uint64_t reserved_7_7:1;
+		uint64_t len:7;
+#else
+		uint64_t len:7;
+		uint64_t reserved_7_7:1;
+		uint64_t fcssel:1;
+		uint64_t reserved_9_63:55;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_rx_bp_dropx {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rx_bp_dropx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t mark:6;
+#else
+		uint64_t mark:6;
+		uint64_t reserved_6_63:58;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_rx_bp_offx {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rx_bp_offx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t mark:6;
+#else
+		uint64_t mark:6;
+		uint64_t reserved_6_63:58;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_rx_bp_onx {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rx_bp_onx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_9_63:55;
+		uint64_t mark:9;
+#else
+		uint64_t mark:9;
+		uint64_t reserved_9_63:55;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_rx_prt_info {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rx_prt_info_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_18_63:46;
+		uint64_t drop:2;
+		uint64_t reserved_2_15:14;
+		uint64_t commit:2;
+#else
+		uint64_t commit:2;
+		uint64_t reserved_2_15:14;
+		uint64_t drop:2;
+		uint64_t reserved_18_63:46;
+#endif
+	} s;
+	struct cvmx_agl_gmx_rx_prt_info_cn56xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_17_63:47;
+		uint64_t drop:1;
+		uint64_t reserved_1_15:15;
+		uint64_t commit:1;
+#else
+		uint64_t commit:1;
+		uint64_t reserved_1_15:15;
+		uint64_t drop:1;
+		uint64_t reserved_17_63:47;
+#endif
+	} cn56xx;
+};
+
+union cvmx_agl_gmx_rx_tx_status {
+	uint64_t u64;
+	struct cvmx_agl_gmx_rx_tx_status_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t tx:2;
+		uint64_t reserved_2_3:2;
+		uint64_t rx:2;
+#else
+		uint64_t rx:2;
+		uint64_t reserved_2_3:2;
+		uint64_t tx:2;
+		uint64_t reserved_6_63:58;
+#endif
+	} s;
+	struct cvmx_agl_gmx_rx_tx_status_cn56xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_5_63:59;
+		uint64_t tx:1;
+		uint64_t reserved_1_3:3;
+		uint64_t rx:1;
+#else
+		uint64_t rx:1;
+		uint64_t reserved_1_3:3;
+		uint64_t tx:1;
+		uint64_t reserved_5_63:59;
+#endif
+	} cn56xx;
+};
+
+union cvmx_agl_gmx_smacx {
+	uint64_t u64;
+	struct cvmx_agl_gmx_smacx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t smac:48;
+#else
+		uint64_t smac:48;
+		uint64_t reserved_48_63:16;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_stat_bp {
+	uint64_t u64;
+	struct cvmx_agl_gmx_stat_bp_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_17_63:47;
+		uint64_t bp:1;
+		uint64_t cnt:16;
+#else
+		uint64_t cnt:16;
+		uint64_t bp:1;
+		uint64_t reserved_17_63:47;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_txx_append {
+	uint64_t u64;
+	struct cvmx_agl_gmx_txx_append_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t force_fcs:1;
+		uint64_t fcs:1;
+		uint64_t pad:1;
+		uint64_t preamble:1;
+#else
+		uint64_t preamble:1;
+		uint64_t pad:1;
+		uint64_t fcs:1;
+		uint64_t force_fcs:1;
+		uint64_t reserved_4_63:60;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_txx_clk {
+	uint64_t u64;
+	struct cvmx_agl_gmx_txx_clk_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t clk_cnt:6;
+#else
+		uint64_t clk_cnt:6;
+		uint64_t reserved_6_63:58;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_txx_ctl {
+	uint64_t u64;
+	struct cvmx_agl_gmx_txx_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t xsdef_en:1;
+		uint64_t xscol_en:1;
+#else
+		uint64_t xscol_en:1;
+		uint64_t xsdef_en:1;
+		uint64_t reserved_2_63:62;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_txx_min_pkt {
+	uint64_t u64;
+	struct cvmx_agl_gmx_txx_min_pkt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t min_size:8;
+#else
+		uint64_t min_size:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_txx_pause_pkt_interval {
+	uint64_t u64;
+	struct cvmx_agl_gmx_txx_pause_pkt_interval_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t interval:16;
+#else
+		uint64_t interval:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_txx_pause_pkt_time {
+	uint64_t u64;
+	struct cvmx_agl_gmx_txx_pause_pkt_time_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t time:16;
+#else
+		uint64_t time:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_txx_pause_togo {
+	uint64_t u64;
+	struct cvmx_agl_gmx_txx_pause_togo_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t time:16;
+#else
+		uint64_t time:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_txx_pause_zero {
+	uint64_t u64;
+	struct cvmx_agl_gmx_txx_pause_zero_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t send:1;
+#else
+		uint64_t send:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_txx_soft_pause {
+	uint64_t u64;
+	struct cvmx_agl_gmx_txx_soft_pause_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t time:16;
+#else
+		uint64_t time:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_txx_stat0 {
+	uint64_t u64;
+	struct cvmx_agl_gmx_txx_stat0_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t xsdef:32;
+		uint64_t xscol:32;
+#else
+		uint64_t xscol:32;
+		uint64_t xsdef:32;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_txx_stat1 {
+	uint64_t u64;
+	struct cvmx_agl_gmx_txx_stat1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t scol:32;
+		uint64_t mcol:32;
+#else
+		uint64_t mcol:32;
+		uint64_t scol:32;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_txx_stat2 {
+	uint64_t u64;
+	struct cvmx_agl_gmx_txx_stat2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t octs:48;
+#else
+		uint64_t octs:48;
+		uint64_t reserved_48_63:16;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_txx_stat3 {
+	uint64_t u64;
+	struct cvmx_agl_gmx_txx_stat3_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t pkts:32;
+#else
+		uint64_t pkts:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_txx_stat4 {
+	uint64_t u64;
+	struct cvmx_agl_gmx_txx_stat4_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t hist1:32;
+		uint64_t hist0:32;
+#else
+		uint64_t hist0:32;
+		uint64_t hist1:32;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_txx_stat5 {
+	uint64_t u64;
+	struct cvmx_agl_gmx_txx_stat5_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t hist3:32;
+		uint64_t hist2:32;
+#else
+		uint64_t hist2:32;
+		uint64_t hist3:32;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_txx_stat6 {
+	uint64_t u64;
+	struct cvmx_agl_gmx_txx_stat6_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t hist5:32;
+		uint64_t hist4:32;
+#else
+		uint64_t hist4:32;
+		uint64_t hist5:32;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_txx_stat7 {
+	uint64_t u64;
+	struct cvmx_agl_gmx_txx_stat7_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t hist7:32;
+		uint64_t hist6:32;
+#else
+		uint64_t hist6:32;
+		uint64_t hist7:32;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_txx_stat8 {
+	uint64_t u64;
+	struct cvmx_agl_gmx_txx_stat8_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t mcst:32;
+		uint64_t bcst:32;
+#else
+		uint64_t bcst:32;
+		uint64_t mcst:32;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_txx_stat9 {
+	uint64_t u64;
+	struct cvmx_agl_gmx_txx_stat9_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t undflw:32;
+		uint64_t ctl:32;
+#else
+		uint64_t ctl:32;
+		uint64_t undflw:32;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_txx_stats_ctl {
+	uint64_t u64;
+	struct cvmx_agl_gmx_txx_stats_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t rd_clr:1;
+#else
+		uint64_t rd_clr:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_txx_thresh {
+	uint64_t u64;
+	struct cvmx_agl_gmx_txx_thresh_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t cnt:6;
+#else
+		uint64_t cnt:6;
+		uint64_t reserved_6_63:58;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_tx_bp {
+	uint64_t u64;
+	struct cvmx_agl_gmx_tx_bp_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t bp:2;
+#else
+		uint64_t bp:2;
+		uint64_t reserved_2_63:62;
+#endif
+	} s;
+	struct cvmx_agl_gmx_tx_bp_cn56xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t bp:1;
+#else
+		uint64_t bp:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} cn56xx;
+};
+
+union cvmx_agl_gmx_tx_col_attempt {
+	uint64_t u64;
+	struct cvmx_agl_gmx_tx_col_attempt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_5_63:59;
+		uint64_t limit:5;
+#else
+		uint64_t limit:5;
+		uint64_t reserved_5_63:59;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_tx_ifg {
+	uint64_t u64;
+	struct cvmx_agl_gmx_tx_ifg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t ifg2:4;
+		uint64_t ifg1:4;
+#else
+		uint64_t ifg1:4;
+		uint64_t ifg2:4;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_tx_int_en {
+	uint64_t u64;
+	struct cvmx_agl_gmx_tx_int_en_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_22_63:42;
+		uint64_t ptp_lost:2;
+		uint64_t reserved_18_19:2;
+		uint64_t late_col:2;
+		uint64_t reserved_14_15:2;
+		uint64_t xsdef:2;
+		uint64_t reserved_10_11:2;
+		uint64_t xscol:2;
+		uint64_t reserved_4_7:4;
+		uint64_t undflw:2;
+		uint64_t reserved_1_1:1;
+		uint64_t pko_nxa:1;
+#else
+		uint64_t pko_nxa:1;
+		uint64_t reserved_1_1:1;
+		uint64_t undflw:2;
+		uint64_t reserved_4_7:4;
+		uint64_t xscol:2;
+		uint64_t reserved_10_11:2;
+		uint64_t xsdef:2;
+		uint64_t reserved_14_15:2;
+		uint64_t late_col:2;
+		uint64_t reserved_18_19:2;
+		uint64_t ptp_lost:2;
+		uint64_t reserved_22_63:42;
+#endif
+	} s;
+	struct cvmx_agl_gmx_tx_int_en_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_18_63:46;
+		uint64_t late_col:2;
+		uint64_t reserved_14_15:2;
+		uint64_t xsdef:2;
+		uint64_t reserved_10_11:2;
+		uint64_t xscol:2;
+		uint64_t reserved_4_7:4;
+		uint64_t undflw:2;
+		uint64_t reserved_1_1:1;
+		uint64_t pko_nxa:1;
+#else
+		uint64_t pko_nxa:1;
+		uint64_t reserved_1_1:1;
+		uint64_t undflw:2;
+		uint64_t reserved_4_7:4;
+		uint64_t xscol:2;
+		uint64_t reserved_10_11:2;
+		uint64_t xsdef:2;
+		uint64_t reserved_14_15:2;
+		uint64_t late_col:2;
+		uint64_t reserved_18_63:46;
+#endif
+	} cn52xx;
+	struct cvmx_agl_gmx_tx_int_en_cn56xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_17_63:47;
+		uint64_t late_col:1;
+		uint64_t reserved_13_15:3;
+		uint64_t xsdef:1;
+		uint64_t reserved_9_11:3;
+		uint64_t xscol:1;
+		uint64_t reserved_3_7:5;
+		uint64_t undflw:1;
+		uint64_t reserved_1_1:1;
+		uint64_t pko_nxa:1;
+#else
+		uint64_t pko_nxa:1;
+		uint64_t reserved_1_1:1;
+		uint64_t undflw:1;
+		uint64_t reserved_3_7:5;
+		uint64_t xscol:1;
+		uint64_t reserved_9_11:3;
+		uint64_t xsdef:1;
+		uint64_t reserved_13_15:3;
+		uint64_t late_col:1;
+		uint64_t reserved_17_63:47;
+#endif
+	} cn56xx;
+};
+
+union cvmx_agl_gmx_tx_int_reg {
+	uint64_t u64;
+	struct cvmx_agl_gmx_tx_int_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_22_63:42;
+		uint64_t ptp_lost:2;
+		uint64_t reserved_18_19:2;
+		uint64_t late_col:2;
+		uint64_t reserved_14_15:2;
+		uint64_t xsdef:2;
+		uint64_t reserved_10_11:2;
+		uint64_t xscol:2;
+		uint64_t reserved_4_7:4;
+		uint64_t undflw:2;
+		uint64_t reserved_1_1:1;
+		uint64_t pko_nxa:1;
+#else
+		uint64_t pko_nxa:1;
+		uint64_t reserved_1_1:1;
+		uint64_t undflw:2;
+		uint64_t reserved_4_7:4;
+		uint64_t xscol:2;
+		uint64_t reserved_10_11:2;
+		uint64_t xsdef:2;
+		uint64_t reserved_14_15:2;
+		uint64_t late_col:2;
+		uint64_t reserved_18_19:2;
+		uint64_t ptp_lost:2;
+		uint64_t reserved_22_63:42;
+#endif
+	} s;
+	struct cvmx_agl_gmx_tx_int_reg_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_18_63:46;
+		uint64_t late_col:2;
+		uint64_t reserved_14_15:2;
+		uint64_t xsdef:2;
+		uint64_t reserved_10_11:2;
+		uint64_t xscol:2;
+		uint64_t reserved_4_7:4;
+		uint64_t undflw:2;
+		uint64_t reserved_1_1:1;
+		uint64_t pko_nxa:1;
+#else
+		uint64_t pko_nxa:1;
+		uint64_t reserved_1_1:1;
+		uint64_t undflw:2;
+		uint64_t reserved_4_7:4;
+		uint64_t xscol:2;
+		uint64_t reserved_10_11:2;
+		uint64_t xsdef:2;
+		uint64_t reserved_14_15:2;
+		uint64_t late_col:2;
+		uint64_t reserved_18_63:46;
+#endif
+	} cn52xx;
+	struct cvmx_agl_gmx_tx_int_reg_cn56xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_17_63:47;
+		uint64_t late_col:1;
+		uint64_t reserved_13_15:3;
+		uint64_t xsdef:1;
+		uint64_t reserved_9_11:3;
+		uint64_t xscol:1;
+		uint64_t reserved_3_7:5;
+		uint64_t undflw:1;
+		uint64_t reserved_1_1:1;
+		uint64_t pko_nxa:1;
+#else
+		uint64_t pko_nxa:1;
+		uint64_t reserved_1_1:1;
+		uint64_t undflw:1;
+		uint64_t reserved_3_7:5;
+		uint64_t xscol:1;
+		uint64_t reserved_9_11:3;
+		uint64_t xsdef:1;
+		uint64_t reserved_13_15:3;
+		uint64_t late_col:1;
+		uint64_t reserved_17_63:47;
+#endif
+	} cn56xx;
+};
+
+union cvmx_agl_gmx_tx_jam {
+	uint64_t u64;
+	struct cvmx_agl_gmx_tx_jam_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t jam:8;
+#else
+		uint64_t jam:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_tx_lfsr {
+	uint64_t u64;
+	struct cvmx_agl_gmx_tx_lfsr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t lfsr:16;
+#else
+		uint64_t lfsr:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_tx_ovr_bp {
+	uint64_t u64;
+	struct cvmx_agl_gmx_tx_ovr_bp_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t en:2;
+		uint64_t reserved_6_7:2;
+		uint64_t bp:2;
+		uint64_t reserved_2_3:2;
+		uint64_t ign_full:2;
+#else
+		uint64_t ign_full:2;
+		uint64_t reserved_2_3:2;
+		uint64_t bp:2;
+		uint64_t reserved_6_7:2;
+		uint64_t en:2;
+		uint64_t reserved_10_63:54;
+#endif
+	} s;
+	struct cvmx_agl_gmx_tx_ovr_bp_cn56xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_9_63:55;
+		uint64_t en:1;
+		uint64_t reserved_5_7:3;
+		uint64_t bp:1;
+		uint64_t reserved_1_3:3;
+		uint64_t ign_full:1;
+#else
+		uint64_t ign_full:1;
+		uint64_t reserved_1_3:3;
+		uint64_t bp:1;
+		uint64_t reserved_5_7:3;
+		uint64_t en:1;
+		uint64_t reserved_9_63:55;
+#endif
+	} cn56xx;
+};
+
+union cvmx_agl_gmx_tx_pause_pkt_dmac {
+	uint64_t u64;
+	struct cvmx_agl_gmx_tx_pause_pkt_dmac_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t dmac:48;
+#else
+		uint64_t dmac:48;
+		uint64_t reserved_48_63:16;
+#endif
+	} s;
+};
+
+union cvmx_agl_gmx_tx_pause_pkt_type {
+	uint64_t u64;
+	struct cvmx_agl_gmx_tx_pause_pkt_type_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t type:16;
+#else
+		uint64_t type:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_agl_prtx_ctl {
+	uint64_t u64;
+	struct cvmx_agl_prtx_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t drv_byp:1;
+		uint64_t reserved_62_62:1;
+		uint64_t cmp_pctl:6;
+		uint64_t reserved_54_55:2;
+		uint64_t cmp_nctl:6;
+		uint64_t reserved_46_47:2;
+		uint64_t drv_pctl:6;
+		uint64_t reserved_38_39:2;
+		uint64_t drv_nctl:6;
+		uint64_t reserved_29_31:3;
+		uint64_t clk_set:5;
+		uint64_t clkrx_byp:1;
+		uint64_t reserved_21_22:2;
+		uint64_t clkrx_set:5;
+		uint64_t clktx_byp:1;
+		uint64_t reserved_13_14:2;
+		uint64_t clktx_set:5;
+		uint64_t reserved_5_7:3;
+		uint64_t dllrst:1;
+		uint64_t comp:1;
+		uint64_t enable:1;
+		uint64_t clkrst:1;
+		uint64_t mode:1;
+#else
+		uint64_t mode:1;
+		uint64_t clkrst:1;
+		uint64_t enable:1;
+		uint64_t comp:1;
+		uint64_t dllrst:1;
+		uint64_t reserved_5_7:3;
+		uint64_t clktx_set:5;
+		uint64_t reserved_13_14:2;
+		uint64_t clktx_byp:1;
+		uint64_t clkrx_set:5;
+		uint64_t reserved_21_22:2;
+		uint64_t clkrx_byp:1;
+		uint64_t clk_set:5;
+		uint64_t reserved_29_31:3;
+		uint64_t drv_nctl:6;
+		uint64_t reserved_38_39:2;
+		uint64_t drv_pctl:6;
+		uint64_t reserved_46_47:2;
+		uint64_t cmp_nctl:6;
+		uint64_t reserved_54_55:2;
+		uint64_t cmp_pctl:6;
+		uint64_t reserved_62_62:1;
+		uint64_t drv_byp:1;
+#endif
+	} s;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-asm.h b/arch/mips/include/asm/octeon/cvmx-asm.h
new file mode 100644
index 000000000..31eacc24b
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-asm.h
@@ -0,0 +1,139 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ *
+ * This is file defines ASM primitives for the executive.
+ */
+#ifndef __CVMX_ASM_H__
+#define __CVMX_ASM_H__
+
+#include <asm/octeon/octeon-model.h>
+
+/* other useful stuff */
+#define CVMX_SYNC asm volatile ("sync" : : : "memory")
+/* String version of SYNCW macro for using in inline asm constructs */
+#define CVMX_SYNCW_STR "syncw\nsyncw\n"
+#ifdef __OCTEON__
+
+/* Deprecated, will be removed in future release */
+#define CVMX_SYNCIO asm volatile ("nop")
+
+#define CVMX_SYNCIOBDMA asm volatile ("synciobdma" : : : "memory")
+
+/* Deprecated, will be removed in future release */
+#define CVMX_SYNCIOALL asm volatile ("nop")
+
+/*
+ * We actually use two syncw instructions in a row when we need a write
+ * memory barrier. This is because the CN3XXX series of Octeons have
+ * errata Core-401. This can cause a single syncw to not enforce
+ * ordering under very rare conditions. Even if it is rare, better safe
+ * than sorry.
+ */
+#define CVMX_SYNCW asm volatile ("syncw\n\tsyncw" : : : "memory")
+
+/*
+ * Define new sync instructions to be normal SYNC instructions for
+ * operating systems that use threads.
+ */
+#define CVMX_SYNCWS CVMX_SYNCW
+#define CVMX_SYNCS  CVMX_SYNC
+#define CVMX_SYNCWS_STR CVMX_SYNCW_STR
+#else
+/*
+ * Not using a Cavium compiler, always use the slower sync so the
+ * assembler stays happy.
+ */
+/* Deprecated, will be removed in future release */
+#define CVMX_SYNCIO asm volatile ("nop")
+
+#define CVMX_SYNCIOBDMA asm volatile ("sync" : : : "memory")
+
+/* Deprecated, will be removed in future release */
+#define CVMX_SYNCIOALL asm volatile ("nop")
+
+#define CVMX_SYNCW asm volatile ("sync" : : : "memory")
+#define CVMX_SYNCWS CVMX_SYNCW
+#define CVMX_SYNCS  CVMX_SYNC
+#define CVMX_SYNCWS_STR CVMX_SYNCW_STR
+#endif
+
+/*
+ * CVMX_PREPARE_FOR_STORE makes each byte of the block unpredictable
+ * (actually old value or zero) until that byte is stored to (by this or
+ * another processor. Note that the value of each byte is not only
+ * unpredictable, but may also change again - up until the point when one
+ * of the cores stores to the byte.
+ */
+#define CVMX_PREPARE_FOR_STORE(address, offset) \
+	asm volatile ("pref 30, " CVMX_TMP_STR(offset) "(%[rbase])" : : \
+	[rbase] "d" (address))
+/*
+ * This is a command headed to the L2 controller to tell it to clear
+ * its dirty bit for a block. Basically, SW is telling HW that the
+ * current version of the block will not be used.
+ */
+#define CVMX_DONT_WRITE_BACK(address, offset) \
+	asm volatile ("pref 29, " CVMX_TMP_STR(offset) "(%[rbase])" : : \
+	[rbase] "d" (address))
+
+/* flush stores, invalidate entire icache */
+#define CVMX_ICACHE_INVALIDATE \
+	{ CVMX_SYNC; asm volatile ("synci 0($0)" : : ); }
+
+/* flush stores, invalidate entire icache */
+#define CVMX_ICACHE_INVALIDATE2 \
+	{ CVMX_SYNC; asm volatile ("cache 0, 0($0)" : : ); }
+
+/* complete prefetches, invalidate entire dcache */
+#define CVMX_DCACHE_INVALIDATE \
+	{ CVMX_SYNC; asm volatile ("cache 9, 0($0)" : : ); }
+
+#define CVMX_CACHE(op, address, offset)					\
+	asm volatile ("cache " CVMX_TMP_STR(op) ", " CVMX_TMP_STR(offset) "(%[rbase])" \
+		: : [rbase] "d" (address) )
+/* fetch and lock the state. */
+#define CVMX_CACHE_LCKL2(address, offset) CVMX_CACHE(31, address, offset)
+/* unlock the state. */
+#define CVMX_CACHE_WBIL2(address, offset) CVMX_CACHE(23, address, offset)
+/* invalidate the cache block and clear the USED bits for the block */
+#define CVMX_CACHE_WBIL2I(address, offset) CVMX_CACHE(3, address, offset)
+/* load virtual tag and data for the L2 cache block into L2C_TAD0_TAG register */
+#define CVMX_CACHE_LTGL2I(address, offset) CVMX_CACHE(7, address, offset)
+
+#define CVMX_POP(result, input) \
+	asm ("pop %[rd],%[rs]" : [rd] "=d" (result) : [rs] "d" (input))
+#define CVMX_DPOP(result, input) \
+	asm ("dpop %[rd],%[rs]" : [rd] "=d" (result) : [rs] "d" (input))
+
+/* some new cop0-like stuff */
+#define CVMX_RDHWR(result, regstr) \
+	asm volatile ("rdhwr %[rt],$" CVMX_TMP_STR(regstr) : [rt] "=d" (result))
+#define CVMX_RDHWRNV(result, regstr) \
+	asm ("rdhwr %[rt],$" CVMX_TMP_STR(regstr) : [rt] "=d" (result))
+#endif /* __CVMX_ASM_H__ */
diff --git a/arch/mips/include/asm/octeon/cvmx-asxx-defs.h b/arch/mips/include/asm/octeon/cvmx-asxx-defs.h
new file mode 100644
index 000000000..70f4a5729
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-asxx-defs.h
@@ -0,0 +1,566 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (C) 2003-2018 Cavium, Inc.
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_ASXX_DEFS_H__
+#define __CVMX_ASXX_DEFS_H__
+
+#define CVMX_ASXX_GMII_RX_CLK_SET(block_id) (CVMX_ADD_IO_SEG(0x00011800B0000180ull))
+#define CVMX_ASXX_GMII_RX_DAT_SET(block_id) (CVMX_ADD_IO_SEG(0x00011800B0000188ull))
+#define CVMX_ASXX_INT_EN(block_id) (CVMX_ADD_IO_SEG(0x00011800B0000018ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_ASXX_INT_REG(block_id) (CVMX_ADD_IO_SEG(0x00011800B0000010ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_ASXX_MII_RX_DAT_SET(block_id) (CVMX_ADD_IO_SEG(0x00011800B0000190ull))
+#define CVMX_ASXX_PRT_LOOP(block_id) (CVMX_ADD_IO_SEG(0x00011800B0000040ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_ASXX_RLD_BYPASS(block_id) (CVMX_ADD_IO_SEG(0x00011800B0000248ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_ASXX_RLD_BYPASS_SETTING(block_id) (CVMX_ADD_IO_SEG(0x00011800B0000250ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_ASXX_RLD_COMP(block_id) (CVMX_ADD_IO_SEG(0x00011800B0000220ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_ASXX_RLD_DATA_DRV(block_id) (CVMX_ADD_IO_SEG(0x00011800B0000218ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_ASXX_RLD_FCRAM_MODE(block_id) (CVMX_ADD_IO_SEG(0x00011800B0000210ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_ASXX_RLD_NCTL_STRONG(block_id) (CVMX_ADD_IO_SEG(0x00011800B0000230ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_ASXX_RLD_NCTL_WEAK(block_id) (CVMX_ADD_IO_SEG(0x00011800B0000240ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_ASXX_RLD_PCTL_STRONG(block_id) (CVMX_ADD_IO_SEG(0x00011800B0000228ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_ASXX_RLD_PCTL_WEAK(block_id) (CVMX_ADD_IO_SEG(0x00011800B0000238ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_ASXX_RLD_SETTING(block_id) (CVMX_ADD_IO_SEG(0x00011800B0000258ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_ASXX_RX_CLK_SETX(offset, block_id) (CVMX_ADD_IO_SEG(0x00011800B0000020ull) + (((offset) & 3) + ((block_id) & 1) * 0x1000000ull) * 8)
+#define CVMX_ASXX_RX_PRT_EN(block_id) (CVMX_ADD_IO_SEG(0x00011800B0000000ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_ASXX_RX_WOL(block_id) (CVMX_ADD_IO_SEG(0x00011800B0000100ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_ASXX_RX_WOL_MSK(block_id) (CVMX_ADD_IO_SEG(0x00011800B0000108ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_ASXX_RX_WOL_POWOK(block_id) (CVMX_ADD_IO_SEG(0x00011800B0000118ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_ASXX_RX_WOL_SIG(block_id) (CVMX_ADD_IO_SEG(0x00011800B0000110ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_ASXX_TX_CLK_SETX(offset, block_id) (CVMX_ADD_IO_SEG(0x00011800B0000048ull) + (((offset) & 3) + ((block_id) & 1) * 0x1000000ull) * 8)
+#define CVMX_ASXX_TX_COMP_BYP(block_id) (CVMX_ADD_IO_SEG(0x00011800B0000068ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_ASXX_TX_HI_WATERX(offset, block_id) (CVMX_ADD_IO_SEG(0x00011800B0000080ull) + (((offset) & 3) + ((block_id) & 1) * 0x1000000ull) * 8)
+#define CVMX_ASXX_TX_PRT_EN(block_id) (CVMX_ADD_IO_SEG(0x00011800B0000008ull) + ((block_id) & 1) * 0x8000000ull)
+
+void __cvmx_interrupt_asxx_enable(int block);
+
+union cvmx_asxx_gmii_rx_clk_set {
+	uint64_t u64;
+	struct cvmx_asxx_gmii_rx_clk_set_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_5_63:59;
+		uint64_t setting:5;
+#else
+		uint64_t setting:5;
+		uint64_t reserved_5_63:59;
+#endif
+	} s;
+};
+
+union cvmx_asxx_gmii_rx_dat_set {
+	uint64_t u64;
+	struct cvmx_asxx_gmii_rx_dat_set_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_5_63:59;
+		uint64_t setting:5;
+#else
+		uint64_t setting:5;
+		uint64_t reserved_5_63:59;
+#endif
+	} s;
+};
+
+union cvmx_asxx_int_en {
+	uint64_t u64;
+	struct cvmx_asxx_int_en_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t txpsh:4;
+		uint64_t txpop:4;
+		uint64_t ovrflw:4;
+#else
+		uint64_t ovrflw:4;
+		uint64_t txpop:4;
+		uint64_t txpsh:4;
+		uint64_t reserved_12_63:52;
+#endif
+	} s;
+	struct cvmx_asxx_int_en_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_11_63:53;
+		uint64_t txpsh:3;
+		uint64_t reserved_7_7:1;
+		uint64_t txpop:3;
+		uint64_t reserved_3_3:1;
+		uint64_t ovrflw:3;
+#else
+		uint64_t ovrflw:3;
+		uint64_t reserved_3_3:1;
+		uint64_t txpop:3;
+		uint64_t reserved_7_7:1;
+		uint64_t txpsh:3;
+		uint64_t reserved_11_63:53;
+#endif
+	} cn30xx;
+};
+
+union cvmx_asxx_int_reg {
+	uint64_t u64;
+	struct cvmx_asxx_int_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t txpsh:4;
+		uint64_t txpop:4;
+		uint64_t ovrflw:4;
+#else
+		uint64_t ovrflw:4;
+		uint64_t txpop:4;
+		uint64_t txpsh:4;
+		uint64_t reserved_12_63:52;
+#endif
+	} s;
+	struct cvmx_asxx_int_reg_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_11_63:53;
+		uint64_t txpsh:3;
+		uint64_t reserved_7_7:1;
+		uint64_t txpop:3;
+		uint64_t reserved_3_3:1;
+		uint64_t ovrflw:3;
+#else
+		uint64_t ovrflw:3;
+		uint64_t reserved_3_3:1;
+		uint64_t txpop:3;
+		uint64_t reserved_7_7:1;
+		uint64_t txpsh:3;
+		uint64_t reserved_11_63:53;
+#endif
+	} cn30xx;
+};
+
+union cvmx_asxx_mii_rx_dat_set {
+	uint64_t u64;
+	struct cvmx_asxx_mii_rx_dat_set_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_5_63:59;
+		uint64_t setting:5;
+#else
+		uint64_t setting:5;
+		uint64_t reserved_5_63:59;
+#endif
+	} s;
+};
+
+union cvmx_asxx_prt_loop {
+	uint64_t u64;
+	struct cvmx_asxx_prt_loop_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t ext_loop:4;
+		uint64_t int_loop:4;
+#else
+		uint64_t int_loop:4;
+		uint64_t ext_loop:4;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+	struct cvmx_asxx_prt_loop_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t ext_loop:3;
+		uint64_t reserved_3_3:1;
+		uint64_t int_loop:3;
+#else
+		uint64_t int_loop:3;
+		uint64_t reserved_3_3:1;
+		uint64_t ext_loop:3;
+		uint64_t reserved_7_63:57;
+#endif
+	} cn30xx;
+};
+
+union cvmx_asxx_rld_bypass {
+	uint64_t u64;
+	struct cvmx_asxx_rld_bypass_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t bypass:1;
+#else
+		uint64_t bypass:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_asxx_rld_bypass_setting {
+	uint64_t u64;
+	struct cvmx_asxx_rld_bypass_setting_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_5_63:59;
+		uint64_t setting:5;
+#else
+		uint64_t setting:5;
+		uint64_t reserved_5_63:59;
+#endif
+	} s;
+};
+
+union cvmx_asxx_rld_comp {
+	uint64_t u64;
+	struct cvmx_asxx_rld_comp_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_9_63:55;
+		uint64_t pctl:5;
+		uint64_t nctl:4;
+#else
+		uint64_t nctl:4;
+		uint64_t pctl:5;
+		uint64_t reserved_9_63:55;
+#endif
+	} s;
+	struct cvmx_asxx_rld_comp_cn38xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t pctl:4;
+		uint64_t nctl:4;
+#else
+		uint64_t nctl:4;
+		uint64_t pctl:4;
+		uint64_t reserved_8_63:56;
+#endif
+	} cn38xx;
+};
+
+union cvmx_asxx_rld_data_drv {
+	uint64_t u64;
+	struct cvmx_asxx_rld_data_drv_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t pctl:4;
+		uint64_t nctl:4;
+#else
+		uint64_t nctl:4;
+		uint64_t pctl:4;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_asxx_rld_fcram_mode {
+	uint64_t u64;
+	struct cvmx_asxx_rld_fcram_mode_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t mode:1;
+#else
+		uint64_t mode:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_asxx_rld_nctl_strong {
+	uint64_t u64;
+	struct cvmx_asxx_rld_nctl_strong_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_5_63:59;
+		uint64_t nctl:5;
+#else
+		uint64_t nctl:5;
+		uint64_t reserved_5_63:59;
+#endif
+	} s;
+};
+
+union cvmx_asxx_rld_nctl_weak {
+	uint64_t u64;
+	struct cvmx_asxx_rld_nctl_weak_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_5_63:59;
+		uint64_t nctl:5;
+#else
+		uint64_t nctl:5;
+		uint64_t reserved_5_63:59;
+#endif
+	} s;
+};
+
+union cvmx_asxx_rld_pctl_strong {
+	uint64_t u64;
+	struct cvmx_asxx_rld_pctl_strong_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_5_63:59;
+		uint64_t pctl:5;
+#else
+		uint64_t pctl:5;
+		uint64_t reserved_5_63:59;
+#endif
+	} s;
+};
+
+union cvmx_asxx_rld_pctl_weak {
+	uint64_t u64;
+	struct cvmx_asxx_rld_pctl_weak_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_5_63:59;
+		uint64_t pctl:5;
+#else
+		uint64_t pctl:5;
+		uint64_t reserved_5_63:59;
+#endif
+	} s;
+};
+
+union cvmx_asxx_rld_setting {
+	uint64_t u64;
+	struct cvmx_asxx_rld_setting_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_13_63:51;
+		uint64_t dfaset:5;
+		uint64_t dfalag:1;
+		uint64_t dfalead:1;
+		uint64_t dfalock:1;
+		uint64_t setting:5;
+#else
+		uint64_t setting:5;
+		uint64_t dfalock:1;
+		uint64_t dfalead:1;
+		uint64_t dfalag:1;
+		uint64_t dfaset:5;
+		uint64_t reserved_13_63:51;
+#endif
+	} s;
+	struct cvmx_asxx_rld_setting_cn38xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_5_63:59;
+		uint64_t setting:5;
+#else
+		uint64_t setting:5;
+		uint64_t reserved_5_63:59;
+#endif
+	} cn38xx;
+};
+
+union cvmx_asxx_rx_clk_setx {
+	uint64_t u64;
+	struct cvmx_asxx_rx_clk_setx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_5_63:59;
+		uint64_t setting:5;
+#else
+		uint64_t setting:5;
+		uint64_t reserved_5_63:59;
+#endif
+	} s;
+};
+
+union cvmx_asxx_rx_prt_en {
+	uint64_t u64;
+	struct cvmx_asxx_rx_prt_en_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t prt_en:4;
+#else
+		uint64_t prt_en:4;
+		uint64_t reserved_4_63:60;
+#endif
+	} s;
+	struct cvmx_asxx_rx_prt_en_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_3_63:61;
+		uint64_t prt_en:3;
+#else
+		uint64_t prt_en:3;
+		uint64_t reserved_3_63:61;
+#endif
+	} cn30xx;
+};
+
+union cvmx_asxx_rx_wol {
+	uint64_t u64;
+	struct cvmx_asxx_rx_wol_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t status:1;
+		uint64_t enable:1;
+#else
+		uint64_t enable:1;
+		uint64_t status:1;
+		uint64_t reserved_2_63:62;
+#endif
+	} s;
+};
+
+union cvmx_asxx_rx_wol_msk {
+	uint64_t u64;
+	struct cvmx_asxx_rx_wol_msk_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t msk:64;
+#else
+		uint64_t msk:64;
+#endif
+	} s;
+};
+
+union cvmx_asxx_rx_wol_powok {
+	uint64_t u64;
+	struct cvmx_asxx_rx_wol_powok_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t powerok:1;
+#else
+		uint64_t powerok:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_asxx_rx_wol_sig {
+	uint64_t u64;
+	struct cvmx_asxx_rx_wol_sig_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t sig:32;
+#else
+		uint64_t sig:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_asxx_tx_clk_setx {
+	uint64_t u64;
+	struct cvmx_asxx_tx_clk_setx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_5_63:59;
+		uint64_t setting:5;
+#else
+		uint64_t setting:5;
+		uint64_t reserved_5_63:59;
+#endif
+	} s;
+};
+
+union cvmx_asxx_tx_comp_byp {
+	uint64_t u64;
+	struct cvmx_asxx_tx_comp_byp_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_0_63:64;
+#else
+		uint64_t reserved_0_63:64;
+#endif
+	} s;
+	struct cvmx_asxx_tx_comp_byp_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_9_63:55;
+		uint64_t bypass:1;
+		uint64_t pctl:4;
+		uint64_t nctl:4;
+#else
+		uint64_t nctl:4;
+		uint64_t pctl:4;
+		uint64_t bypass:1;
+		uint64_t reserved_9_63:55;
+#endif
+	} cn30xx;
+	struct cvmx_asxx_tx_comp_byp_cn38xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t pctl:4;
+		uint64_t nctl:4;
+#else
+		uint64_t nctl:4;
+		uint64_t pctl:4;
+		uint64_t reserved_8_63:56;
+#endif
+	} cn38xx;
+	struct cvmx_asxx_tx_comp_byp_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_17_63:47;
+		uint64_t bypass:1;
+		uint64_t reserved_13_15:3;
+		uint64_t pctl:5;
+		uint64_t reserved_5_7:3;
+		uint64_t nctl:5;
+#else
+		uint64_t nctl:5;
+		uint64_t reserved_5_7:3;
+		uint64_t pctl:5;
+		uint64_t reserved_13_15:3;
+		uint64_t bypass:1;
+		uint64_t reserved_17_63:47;
+#endif
+	} cn50xx;
+	struct cvmx_asxx_tx_comp_byp_cn58xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_13_63:51;
+		uint64_t pctl:5;
+		uint64_t reserved_5_7:3;
+		uint64_t nctl:5;
+#else
+		uint64_t nctl:5;
+		uint64_t reserved_5_7:3;
+		uint64_t pctl:5;
+		uint64_t reserved_13_63:51;
+#endif
+	} cn58xx;
+};
+
+union cvmx_asxx_tx_hi_waterx {
+	uint64_t u64;
+	struct cvmx_asxx_tx_hi_waterx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t mark:4;
+#else
+		uint64_t mark:4;
+		uint64_t reserved_4_63:60;
+#endif
+	} s;
+	struct cvmx_asxx_tx_hi_waterx_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_3_63:61;
+		uint64_t mark:3;
+#else
+		uint64_t mark:3;
+		uint64_t reserved_3_63:61;
+#endif
+	} cn30xx;
+};
+
+union cvmx_asxx_tx_prt_en {
+	uint64_t u64;
+	struct cvmx_asxx_tx_prt_en_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t prt_en:4;
+#else
+		uint64_t prt_en:4;
+		uint64_t reserved_4_63:60;
+#endif
+	} s;
+	struct cvmx_asxx_tx_prt_en_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_3_63:61;
+		uint64_t prt_en:3;
+#else
+		uint64_t prt_en:3;
+		uint64_t reserved_3_63:61;
+#endif
+	} cn30xx;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-boot-vector.h b/arch/mips/include/asm/octeon/cvmx-boot-vector.h
new file mode 100644
index 000000000..8db08241d
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-boot-vector.h
@@ -0,0 +1,53 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003-2017 Cavium, Inc.
+ */
+
+#ifndef __CVMX_BOOT_VECTOR_H__
+#define __CVMX_BOOT_VECTOR_H__
+
+#include <asm/octeon/octeon.h>
+
+/*
+ * The boot vector table is made up of an array of 1024 elements of
+ * struct cvmx_boot_vector_element.  There is one entry for each
+ * possible MIPS CPUNum, indexed by the CPUNum.
+ *
+ * Once cvmx_boot_vector_get() returns a non-NULL value (indicating
+ * success), NMI to a core will cause execution to transfer to the
+ * target_ptr location for that core's entry in the vector table.
+ *
+ * The struct cvmx_boot_vector_element fields app0, app1, and app2 can
+ * be used by the application that has set the target_ptr in any
+ * application specific manner, they are not touched by the vectoring
+ * code.
+ *
+ * The boot vector code clobbers the CP0_DESAVE register, and on
+ * OCTEON II and later CPUs also clobbers CP0_KScratch2.  All GP
+ * registers are preserved, except on pre-OCTEON II CPUs, where k1 is
+ * clobbered.
+ *
+ */
+
+
+/*
+ * Applications install the boot bus code in cvmx-boot-vector.c, which
+ * uses this magic:
+ */
+#define OCTEON_BOOT_MOVEABLE_MAGIC1 0xdb00110ad358eacdull
+
+struct cvmx_boot_vector_element {
+	/* kseg0 or xkphys address of target code. */
+	uint64_t target_ptr;
+	/* Three application specific arguments. */
+	uint64_t app0;
+	uint64_t app1;
+	uint64_t app2;
+};
+
+struct cvmx_boot_vector_element *cvmx_boot_vector_get(void);
+
+#endif /* __CVMX_BOOT_VECTOR_H__ */
diff --git a/arch/mips/include/asm/octeon/cvmx-bootinfo.h b/arch/mips/include/asm/octeon/cvmx-bootinfo.h
new file mode 100644
index 000000000..c1c0b3230
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-bootinfo.h
@@ -0,0 +1,428 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ * Header file containing the ABI with the bootloader.
+ */
+
+#ifndef __CVMX_BOOTINFO_H__
+#define __CVMX_BOOTINFO_H__
+
+#include "cvmx-coremask.h"
+
+/*
+ * Current major and minor versions of the CVMX bootinfo block that is
+ * passed from the bootloader to the application.  This is versioned
+ * so that applications can properly handle multiple bootloader
+ * versions.
+ */
+#define CVMX_BOOTINFO_MAJ_VER 1
+#define CVMX_BOOTINFO_MIN_VER 4
+
+#if (CVMX_BOOTINFO_MAJ_VER == 1)
+#define CVMX_BOOTINFO_OCTEON_SERIAL_LEN 20
+/*
+ * This structure is populated by the bootloader.  For binary
+ * compatibility the only changes that should be made are
+ * adding members to the end of the structure, and the minor
+ * version should be incremented at that time.
+ * If an incompatible change is made, the major version
+ * must be incremented, and the minor version should be reset
+ * to 0.
+ */
+struct cvmx_bootinfo {
+#ifdef __BIG_ENDIAN_BITFIELD
+	uint32_t major_version;
+	uint32_t minor_version;
+
+	uint64_t stack_top;
+	uint64_t heap_base;
+	uint64_t heap_end;
+	uint64_t desc_vaddr;
+
+	uint32_t exception_base_addr;
+	uint32_t stack_size;
+	uint32_t flags;
+	uint32_t core_mask;
+	/* DRAM size in megabytes */
+	uint32_t dram_size;
+	/* physical address of free memory descriptor block*/
+	uint32_t phy_mem_desc_addr;
+	/* used to pass flags from app to debugger */
+	uint32_t debugger_flags_base_addr;
+
+	/* CPU clock speed, in hz */
+	uint32_t eclock_hz;
+
+	/* DRAM clock speed, in hz */
+	uint32_t dclock_hz;
+
+	uint32_t reserved0;
+	uint16_t board_type;
+	uint8_t board_rev_major;
+	uint8_t board_rev_minor;
+	uint16_t reserved1;
+	uint8_t reserved2;
+	uint8_t reserved3;
+	char board_serial_number[CVMX_BOOTINFO_OCTEON_SERIAL_LEN];
+	uint8_t mac_addr_base[6];
+	uint8_t mac_addr_count;
+#if (CVMX_BOOTINFO_MIN_VER >= 1)
+	/*
+	 * Several boards support compact flash on the Octeon boot
+	 * bus.	 The CF memory spaces may be mapped to different
+	 * addresses on different boards.  These are the physical
+	 * addresses, so care must be taken to use the correct
+	 * XKPHYS/KSEG0 addressing depending on the application's
+	 * ABI.	 These values will be 0 if CF is not present.
+	 */
+	uint64_t compact_flash_common_base_addr;
+	uint64_t compact_flash_attribute_base_addr;
+	/*
+	 * Base address of the LED display (as on EBT3000 board)
+	 * This will be 0 if LED display not present.
+	 */
+	uint64_t led_display_base_addr;
+#endif
+#if (CVMX_BOOTINFO_MIN_VER >= 2)
+	/* DFA reference clock in hz (if applicable)*/
+	uint32_t dfa_ref_clock_hz;
+
+	/*
+	 * flags indicating various configuration options.  These
+	 * flags supercede the 'flags' variable and should be used
+	 * instead if available.
+	 */
+	uint32_t config_flags;
+#endif
+#if (CVMX_BOOTINFO_MIN_VER >= 3)
+	/*
+	 * Address of the OF Flattened Device Tree structure
+	 * describing the board.
+	 */
+	uint64_t fdt_addr;
+#endif
+#if (CVMX_BOOTINFO_MIN_VER >= 4)
+	/*
+	 * Coremask used for processors with more than 32 cores
+	 * or with OCI.  This replaces core_mask.
+	 */
+	struct cvmx_coremask ext_core_mask;
+#endif
+#else				/* __BIG_ENDIAN */
+	/*
+	 * Little-Endian: When the CPU mode is switched to
+	 * little-endian, the view of the structure has some of the
+	 * fields swapped.
+	 */
+	uint32_t minor_version;
+	uint32_t major_version;
+
+	uint64_t stack_top;
+	uint64_t heap_base;
+	uint64_t heap_end;
+	uint64_t desc_vaddr;
+
+	uint32_t stack_size;
+	uint32_t exception_base_addr;
+
+	uint32_t core_mask;
+	uint32_t flags;
+
+	uint32_t phy_mem_desc_addr;
+	uint32_t dram_size;
+
+	uint32_t eclock_hz;
+	uint32_t debugger_flags_base_addr;
+
+	uint32_t reserved0;
+	uint32_t dclock_hz;
+
+	uint8_t reserved3;
+	uint8_t reserved2;
+	uint16_t reserved1;
+	uint8_t board_rev_minor;
+	uint8_t board_rev_major;
+	uint16_t board_type;
+
+	char board_serial_number[CVMX_BOOTINFO_OCTEON_SERIAL_LEN];
+	uint8_t mac_addr_base[6];
+	uint8_t mac_addr_count;
+	uint8_t pad[5];
+
+#if (CVMX_BOOTINFO_MIN_VER >= 1)
+	uint64_t compact_flash_common_base_addr;
+	uint64_t compact_flash_attribute_base_addr;
+	uint64_t led_display_base_addr;
+#endif
+#if (CVMX_BOOTINFO_MIN_VER >= 2)
+	uint32_t config_flags;
+	uint32_t dfa_ref_clock_hz;
+#endif
+#if (CVMX_BOOTINFO_MIN_VER >= 3)
+	uint64_t fdt_addr;
+#endif
+#if (CVMX_BOOTINFO_MIN_VER >= 4)
+	struct cvmx_coremask ext_core_mask;
+#endif
+#endif
+};
+
+#define CVMX_BOOTINFO_CFG_FLAG_PCI_HOST			(1ull << 0)
+#define CVMX_BOOTINFO_CFG_FLAG_PCI_TARGET		(1ull << 1)
+#define CVMX_BOOTINFO_CFG_FLAG_DEBUG			(1ull << 2)
+#define CVMX_BOOTINFO_CFG_FLAG_NO_MAGIC			(1ull << 3)
+/* This flag is set if the TLB mappings are not contained in the
+ * 0x10000000 - 0x20000000 boot bus region. */
+#define CVMX_BOOTINFO_CFG_FLAG_OVERSIZE_TLB_MAPPING	(1ull << 4)
+#define CVMX_BOOTINFO_CFG_FLAG_BREAK			(1ull << 5)
+
+#endif /*   (CVMX_BOOTINFO_MAJ_VER == 1) */
+
+/* Type defines for board and chip types */
+enum cvmx_board_types_enum {
+	CVMX_BOARD_TYPE_NULL = 0,
+	CVMX_BOARD_TYPE_SIM = 1,
+	CVMX_BOARD_TYPE_EBT3000 = 2,
+	CVMX_BOARD_TYPE_KODAMA = 3,
+	CVMX_BOARD_TYPE_NIAGARA = 4,
+	CVMX_BOARD_TYPE_NAC38 = 5,	/* formerly NAO38 */
+	CVMX_BOARD_TYPE_THUNDER = 6,
+	CVMX_BOARD_TYPE_TRANTOR = 7,
+	CVMX_BOARD_TYPE_EBH3000 = 8,
+	CVMX_BOARD_TYPE_EBH3100 = 9,
+	CVMX_BOARD_TYPE_HIKARI = 10,
+	CVMX_BOARD_TYPE_CN3010_EVB_HS5 = 11,
+	CVMX_BOARD_TYPE_CN3005_EVB_HS5 = 12,
+	CVMX_BOARD_TYPE_KBP = 13,
+	/* Deprecated, CVMX_BOARD_TYPE_CN3010_EVB_HS5 supports the CN3020 */
+	CVMX_BOARD_TYPE_CN3020_EVB_HS5 = 14,
+	CVMX_BOARD_TYPE_EBT5800 = 15,
+	CVMX_BOARD_TYPE_NICPRO2 = 16,
+	CVMX_BOARD_TYPE_EBH5600 = 17,
+	CVMX_BOARD_TYPE_EBH5601 = 18,
+	CVMX_BOARD_TYPE_EBH5200 = 19,
+	CVMX_BOARD_TYPE_BBGW_REF = 20,
+	CVMX_BOARD_TYPE_NIC_XLE_4G = 21,
+	CVMX_BOARD_TYPE_EBT5600 = 22,
+	CVMX_BOARD_TYPE_EBH5201 = 23,
+	CVMX_BOARD_TYPE_EBT5200 = 24,
+	CVMX_BOARD_TYPE_CB5600	= 25,
+	CVMX_BOARD_TYPE_CB5601	= 26,
+	CVMX_BOARD_TYPE_CB5200	= 27,
+	/* Special 'generic' board type, supports many boards */
+	CVMX_BOARD_TYPE_GENERIC = 28,
+	CVMX_BOARD_TYPE_EBH5610 = 29,
+	CVMX_BOARD_TYPE_LANAI2_A = 30,
+	CVMX_BOARD_TYPE_LANAI2_U = 31,
+	CVMX_BOARD_TYPE_EBB5600 = 32,
+	CVMX_BOARD_TYPE_EBB6300 = 33,
+	CVMX_BOARD_TYPE_NIC_XLE_10G = 34,
+	CVMX_BOARD_TYPE_LANAI2_G = 35,
+	CVMX_BOARD_TYPE_EBT5810 = 36,
+	CVMX_BOARD_TYPE_NIC10E = 37,
+	CVMX_BOARD_TYPE_EP6300C = 38,
+	CVMX_BOARD_TYPE_EBB6800 = 39,
+	CVMX_BOARD_TYPE_NIC4E = 40,
+	CVMX_BOARD_TYPE_NIC2E = 41,
+	CVMX_BOARD_TYPE_EBB6600 = 42,
+	CVMX_BOARD_TYPE_REDWING = 43,
+	CVMX_BOARD_TYPE_NIC68_4 = 44,
+	CVMX_BOARD_TYPE_NIC10E_66 = 45,
+	CVMX_BOARD_TYPE_SNIC10E = 50,
+	CVMX_BOARD_TYPE_MAX,
+
+	/*
+	 * The range from CVMX_BOARD_TYPE_MAX to
+	 * CVMX_BOARD_TYPE_CUST_DEFINED_MIN is reserved for future
+	 * SDK use.
+	 */
+
+	/*
+	 * Set aside a range for customer boards.  These numbers are managed
+	 * by Cavium.
+	 */
+	CVMX_BOARD_TYPE_CUST_DEFINED_MIN = 10000,
+	CVMX_BOARD_TYPE_CUST_WSX16 = 10001,
+	CVMX_BOARD_TYPE_CUST_NS0216 = 10002,
+	CVMX_BOARD_TYPE_CUST_NB5 = 10003,
+	CVMX_BOARD_TYPE_CUST_WMR500 = 10004,
+	CVMX_BOARD_TYPE_CUST_ITB101 = 10005,
+	CVMX_BOARD_TYPE_CUST_NTE102 = 10006,
+	CVMX_BOARD_TYPE_CUST_AGS103 = 10007,
+	CVMX_BOARD_TYPE_CUST_GST104 = 10008,
+	CVMX_BOARD_TYPE_CUST_GCT105 = 10009,
+	CVMX_BOARD_TYPE_CUST_AGS106 = 10010,
+	CVMX_BOARD_TYPE_CUST_SGM107 = 10011,
+	CVMX_BOARD_TYPE_CUST_GCT108 = 10012,
+	CVMX_BOARD_TYPE_CUST_AGS109 = 10013,
+	CVMX_BOARD_TYPE_CUST_GCT110 = 10014,
+	CVMX_BOARD_TYPE_CUST_L2_AIR_SENDER = 10015,
+	CVMX_BOARD_TYPE_CUST_L2_AIR_RECEIVER = 10016,
+	CVMX_BOARD_TYPE_CUST_L2_ACCTON2_TX = 10017,
+	CVMX_BOARD_TYPE_CUST_L2_ACCTON2_RX = 10018,
+	CVMX_BOARD_TYPE_CUST_L2_WSTRNSNIC_TX = 10019,
+	CVMX_BOARD_TYPE_CUST_L2_WSTRNSNIC_RX = 10020,
+	CVMX_BOARD_TYPE_CUST_L2_ZINWELL = 10021,
+	CVMX_BOARD_TYPE_CUST_DEFINED_MAX = 20000,
+
+	/*
+	 * Set aside a range for customer private use.	The SDK won't
+	 * use any numbers in this range.
+	 */
+	CVMX_BOARD_TYPE_CUST_PRIVATE_MIN = 20001,
+	CVMX_BOARD_TYPE_UBNT_E100 = 20002,
+	CVMX_BOARD_TYPE_UBNT_E200 = 20003,
+	CVMX_BOARD_TYPE_UBNT_E220 = 20005,
+	CVMX_BOARD_TYPE_CUST_DSR1000N = 20006,
+	CVMX_BOARD_TYPE_UBNT_E300 = 20300,
+	CVMX_BOARD_TYPE_KONTRON_S1901 = 21901,
+	CVMX_BOARD_TYPE_CUST_PRIVATE_MAX = 30000,
+
+	/* The remaining range is reserved for future use. */
+};
+
+enum cvmx_chip_types_enum {
+	CVMX_CHIP_TYPE_NULL = 0,
+	CVMX_CHIP_SIM_TYPE_DEPRECATED = 1,
+	CVMX_CHIP_TYPE_OCTEON_SAMPLE = 2,
+	CVMX_CHIP_TYPE_MAX,
+};
+
+/* Compatibility alias for NAC38 name change, planned to be removed
+ * from SDK 1.7 */
+#define CVMX_BOARD_TYPE_NAO38	CVMX_BOARD_TYPE_NAC38
+
+/* Functions to return string based on type */
+#define ENUM_BRD_TYPE_CASE(x) \
+	case x: return (&#x[16]);	/* Skip CVMX_BOARD_TYPE_ */
+static inline const char *cvmx_board_type_to_string(enum
+						    cvmx_board_types_enum type)
+{
+	switch (type) {
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_NULL)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_SIM)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_EBT3000)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_KODAMA)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_NIAGARA)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_NAC38)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_THUNDER)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_TRANTOR)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_EBH3000)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_EBH3100)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_HIKARI)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CN3010_EVB_HS5)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CN3005_EVB_HS5)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_KBP)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CN3020_EVB_HS5)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_EBT5800)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_NICPRO2)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_EBH5600)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_EBH5601)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_EBH5200)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_BBGW_REF)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_NIC_XLE_4G)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_EBT5600)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_EBH5201)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_EBT5200)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CB5600)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CB5601)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CB5200)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_GENERIC)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_EBH5610)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_LANAI2_A)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_LANAI2_U)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_EBB5600)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_EBB6300)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_NIC_XLE_10G)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_LANAI2_G)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_EBT5810)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_NIC10E)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_EP6300C)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_EBB6800)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_NIC4E)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_NIC2E)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_EBB6600)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_REDWING)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_NIC68_4)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_NIC10E_66)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_SNIC10E)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_MAX)
+
+			/* Customer boards listed here */
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_DEFINED_MIN)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_WSX16)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_NS0216)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_NB5)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_WMR500)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_ITB101)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_NTE102)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_AGS103)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_GST104)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_GCT105)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_AGS106)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_SGM107)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_GCT108)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_AGS109)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_GCT110)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_L2_AIR_SENDER)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_L2_AIR_RECEIVER)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_L2_ACCTON2_TX)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_L2_ACCTON2_RX)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_L2_WSTRNSNIC_TX)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_L2_WSTRNSNIC_RX)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_L2_ZINWELL)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_DEFINED_MAX)
+
+		    /* Customer private range */
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_PRIVATE_MIN)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_UBNT_E100)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_UBNT_E200)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_UBNT_E220)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_DSR1000N)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_UBNT_E300)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_KONTRON_S1901)
+		ENUM_BRD_TYPE_CASE(CVMX_BOARD_TYPE_CUST_PRIVATE_MAX)
+	}
+	return NULL;
+}
+
+#define ENUM_CHIP_TYPE_CASE(x) \
+	case x: return (&#x[15]);	/* Skip CVMX_CHIP_TYPE */
+static inline const char *cvmx_chip_type_to_string(enum
+						   cvmx_chip_types_enum type)
+{
+	switch (type) {
+		ENUM_CHIP_TYPE_CASE(CVMX_CHIP_TYPE_NULL)
+		ENUM_CHIP_TYPE_CASE(CVMX_CHIP_SIM_TYPE_DEPRECATED)
+		ENUM_CHIP_TYPE_CASE(CVMX_CHIP_TYPE_OCTEON_SAMPLE)
+		ENUM_CHIP_TYPE_CASE(CVMX_CHIP_TYPE_MAX)
+	}
+	return "Unsupported Chip";
+}
+
+#endif /* __CVMX_BOOTINFO_H__ */
diff --git a/arch/mips/include/asm/octeon/cvmx-bootmem.h b/arch/mips/include/asm/octeon/cvmx-bootmem.h
new file mode 100644
index 000000000..689a82cac
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-bootmem.h
@@ -0,0 +1,341 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ * Simple allocate only memory allocator.  Used to allocate memory at
+ * application start time.
+ */
+
+#ifndef __CVMX_BOOTMEM_H__
+#define __CVMX_BOOTMEM_H__
+/* Must be multiple of 8, changing breaks ABI */
+#define CVMX_BOOTMEM_NAME_LEN 128
+
+/* Can change without breaking ABI */
+#define CVMX_BOOTMEM_NUM_NAMED_BLOCKS 64
+
+/* minimum alignment of bootmem alloced blocks */
+#define CVMX_BOOTMEM_ALIGNMENT_SIZE	(16ull)
+
+/* Flags for cvmx_bootmem_phy_mem* functions */
+/* Allocate from end of block instead of beginning */
+#define CVMX_BOOTMEM_FLAG_END_ALLOC    (1 << 0)
+
+/* Don't do any locking. */
+#define CVMX_BOOTMEM_FLAG_NO_LOCKING   (1 << 1)
+
+/* First bytes of each free physical block of memory contain this structure,
+ * which is used to maintain the free memory list.  Since the bootloader is
+ * only 32 bits, there is a union providing 64 and 32 bit versions.  The
+ * application init code converts addresses to 64 bit addresses before the
+ * application starts.
+ */
+struct cvmx_bootmem_block_header {
+	/*
+	 * Note: these are referenced from assembly routines in the
+	 * bootloader, so this structure should not be changed
+	 * without changing those routines as well.
+	 */
+	uint64_t next_block_addr;
+	uint64_t size;
+
+};
+
+/*
+ * Structure for named memory blocks.  Number of descriptors available
+ * can be changed without affecting compatibility, but name length
+ * changes require a bump in the bootmem descriptor version Note: This
+ * structure must be naturally 64 bit aligned, as a single memory
+ * image will be used by both 32 and 64 bit programs.
+ */
+struct cvmx_bootmem_named_block_desc {
+	/* Base address of named block */
+	uint64_t base_addr;
+	/*
+	 * Size actually allocated for named block (may differ from
+	 * requested).
+	 */
+	uint64_t size;
+	/* name of named block */
+	char name[CVMX_BOOTMEM_NAME_LEN];
+};
+
+/* Current descriptor versions */
+/* CVMX bootmem descriptor major version */
+#define CVMX_BOOTMEM_DESC_MAJ_VER   3
+
+/* CVMX bootmem descriptor minor version */
+#define CVMX_BOOTMEM_DESC_MIN_VER   0
+
+/* First three members of cvmx_bootmem_desc_t are left in original
+ * positions for backwards compatibility.
+ */
+struct cvmx_bootmem_desc {
+#if defined(__BIG_ENDIAN_BITFIELD) || defined(CVMX_BUILD_FOR_LINUX_HOST)
+	/* spinlock to control access to list */
+	uint32_t lock;
+	/* flags for indicating various conditions */
+	uint32_t flags;
+	uint64_t head_addr;
+
+	/* Incremented when incompatible changes made */
+	uint32_t major_version;
+
+	/*
+	 * Incremented changed when compatible changes made, reset to
+	 * zero when major incremented.
+	 */
+	uint32_t minor_version;
+
+	uint64_t app_data_addr;
+	uint64_t app_data_size;
+
+	/* number of elements in named blocks array */
+	uint32_t named_block_num_blocks;
+
+	/* length of name array in bootmem blocks */
+	uint32_t named_block_name_len;
+	/* address of named memory block descriptors */
+	uint64_t named_block_array_addr;
+#else                           /* __LITTLE_ENDIAN */
+	uint32_t flags;
+	uint32_t lock;
+	uint64_t head_addr;
+
+	uint32_t minor_version;
+	uint32_t major_version;
+	uint64_t app_data_addr;
+	uint64_t app_data_size;
+
+	uint32_t named_block_name_len;
+	uint32_t named_block_num_blocks;
+	uint64_t named_block_array_addr;
+#endif
+};
+
+/**
+ * Initialize the boot alloc memory structures. This is
+ * normally called inside of cvmx_user_app_init()
+ *
+ * @mem_desc_ptr:	Address of the free memory list
+ */
+extern int cvmx_bootmem_init(void *mem_desc_ptr);
+
+/**
+ * Allocate a block of memory from the free list that was
+ * passed to the application by the bootloader at a specific
+ * address. This is an allocate-only algorithm, so
+ * freeing memory is not possible. Allocation will fail if
+ * memory cannot be allocated at the specified address.
+ *
+ * @size:      Size in bytes of block to allocate
+ * @address:   Physical address to allocate memory at.	If this memory is not
+ *		    available, the allocation fails.
+ * @alignment: Alignment required - must be power of 2
+ * Returns pointer to block of memory, NULL on error
+ */
+extern void *cvmx_bootmem_alloc_address(uint64_t size, uint64_t address,
+					uint64_t alignment);
+
+/**
+ * Frees a previously allocated named bootmem block.
+ *
+ * @name:   name of block to free
+ *
+ * Returns 0 on failure,
+ *	   !0 on success
+ */
+
+
+/**
+ * Allocate a block of memory from the free list that was passed
+ * to the application by the bootloader, and assign it a name in the
+ * global named block table.  (part of the cvmx_bootmem_descriptor_t structure)
+ * Named blocks can later be freed.
+ *
+ * @size:      Size in bytes of block to allocate
+ * @alignment: Alignment required - must be power of 2
+ * @name:      name of block - must be less than CVMX_BOOTMEM_NAME_LEN bytes
+ *
+ * Returns a pointer to block of memory, NULL on error
+ */
+extern void *cvmx_bootmem_alloc_named(uint64_t size, uint64_t alignment,
+				      char *name);
+
+/**
+ * Allocate a block of memory from a specific range of the free list
+ * that was passed to the application by the bootloader, and assign it
+ * a name in the global named block table.  (part of the
+ * cvmx_bootmem_descriptor_t structure) Named blocks can later be
+ * freed.  If request cannot be satisfied within the address range
+ * specified, NULL is returned
+ *
+ * @size:      Size in bytes of block to allocate
+ * @min_addr:  minimum address of range
+ * @max_addr:  maximum address of range
+ * @align:     Alignment of memory to be allocated. (must be a power of 2)
+ * @name:      name of block - must be less than CVMX_BOOTMEM_NAME_LEN bytes
+ *
+ * Returns a pointer to block of memory, NULL on error
+ */
+extern void *cvmx_bootmem_alloc_named_range(uint64_t size, uint64_t min_addr,
+					    uint64_t max_addr, uint64_t align,
+					    char *name);
+
+/**
+ * Allocate if needed a block of memory from a specific range of the
+ * free list that was passed to the application by the bootloader, and
+ * assign it a name in the global named block table.  (part of the
+ * cvmx_bootmem_descriptor_t structure) Named blocks can later be
+ * freed.  If the requested name block is already allocated, return
+ * the pointer to block of memory.  If request cannot be satisfied
+ * within the address range specified, NULL is returned
+ *
+ * @param size   Size in bytes of block to allocate
+ * @param min_addr  minimum address of range
+ * @param max_addr  maximum address of range
+ * @param align  Alignment of memory to be allocated. (must be a power of 2)
+ * @param name   name of block - must be less than CVMX_BOOTMEM_NAME_LEN bytes
+ * @param init   Initialization function
+ *
+ * The initialization function is optional, if omitted the named block
+ * is initialized to all zeros when it is created, i.e. once.
+ *
+ * @return pointer to block of memory, NULL on error
+ */
+void *cvmx_bootmem_alloc_named_range_once(uint64_t size,
+					  uint64_t min_addr,
+					  uint64_t max_addr,
+					  uint64_t align,
+					  char *name,
+					  void (*init) (void *));
+
+extern int cvmx_bootmem_free_named(char *name);
+
+/**
+ * Finds a named bootmem block by name.
+ *
+ * @name:   name of block to free
+ *
+ * Returns pointer to named block descriptor on success
+ *	   0 on failure
+ */
+struct cvmx_bootmem_named_block_desc *cvmx_bootmem_find_named_block(char *name);
+
+/**
+ * Allocates a block of physical memory from the free list, at
+ * (optional) requested address and alignment.
+ *
+ * @req_size: size of region to allocate.  All requests are rounded up
+ *	      to be a multiple CVMX_BOOTMEM_ALIGNMENT_SIZE bytes size
+ *
+ * @address_min: Minimum address that block can occupy.
+ *
+ * @address_max: Specifies the maximum address_min (inclusive) that
+ *		 the allocation can use.
+ *
+ * @alignment: Requested alignment of the block.  If this alignment
+ *	       cannot be met, the allocation fails.  This must be a
+ *	       power of 2.  (Note: Alignment of
+ *	       CVMX_BOOTMEM_ALIGNMENT_SIZE bytes is required, and
+ *	       internally enforced.  Requested alignments of less than
+ *	       CVMX_BOOTMEM_ALIGNMENT_SIZE are set to
+ *	       CVMX_BOOTMEM_ALIGNMENT_SIZE.)
+ *
+ * @flags:     Flags to control options for the allocation.
+ *
+ * Returns physical address of block allocated, or -1 on failure
+ */
+int64_t cvmx_bootmem_phy_alloc(uint64_t req_size, uint64_t address_min,
+			       uint64_t address_max, uint64_t alignment,
+			       uint32_t flags);
+
+/**
+ * Allocates a named block of physical memory from the free list, at
+ * (optional) requested address and alignment.
+ *
+ * @param size	    size of region to allocate.	 All requests are rounded
+ *		    up to be a multiple CVMX_BOOTMEM_ALIGNMENT_SIZE
+ *		    bytes size
+ * @param min_addr Minimum address that block can occupy.
+ * @param max_addr  Specifies the maximum address_min (inclusive) that
+ *		    the allocation can use.
+ * @param alignment Requested alignment of the block.  If this
+ *		    alignment cannot be met, the allocation fails.
+ *		    This must be a power of 2.	(Note: Alignment of
+ *		    CVMX_BOOTMEM_ALIGNMENT_SIZE bytes is required, and
+ *		    internally enforced.  Requested alignments of less
+ *		    than CVMX_BOOTMEM_ALIGNMENT_SIZE are set to
+ *		    CVMX_BOOTMEM_ALIGNMENT_SIZE.)
+ * @param name	    name to assign to named block
+ * @param flags	    Flags to control options for the allocation.
+ *
+ * @return physical address of block allocated, or -1 on failure
+ */
+int64_t cvmx_bootmem_phy_named_block_alloc(uint64_t size, uint64_t min_addr,
+					   uint64_t max_addr,
+					   uint64_t alignment,
+					   char *name, uint32_t flags);
+
+/**
+ * Frees a block to the bootmem allocator list.	 This must
+ * be used with care, as the size provided must match the size
+ * of the block that was allocated, or the list will become
+ * corrupted.
+ *
+ * IMPORTANT:  This is only intended to be used as part of named block
+ * frees and initial population of the free memory list.
+ *							*
+ *
+ * @phy_addr: physical address of block
+ * @size:     size of block in bytes.
+ * @flags:    flags for passing options
+ *
+ * Returns 1 on success,
+ *	   0 on failure
+ */
+int __cvmx_bootmem_phy_free(uint64_t phy_addr, uint64_t size, uint32_t flags);
+
+/**
+ * Locks the bootmem allocator.	 This is useful in certain situations
+ * where multiple allocations must be made without being interrupted.
+ * This should be used with the CVMX_BOOTMEM_FLAG_NO_LOCKING flag.
+ *
+ */
+void cvmx_bootmem_lock(void);
+
+/**
+ * Unlocks the bootmem allocator.  This is useful in certain situations
+ * where multiple allocations must be made without being interrupted.
+ * This should be used with the CVMX_BOOTMEM_FLAG_NO_LOCKING flag.
+ *
+ */
+void cvmx_bootmem_unlock(void);
+
+extern struct cvmx_bootmem_desc *cvmx_bootmem_get_desc(void);
+
+#endif /*   __CVMX_BOOTMEM_H__ */
diff --git a/arch/mips/include/asm/octeon/cvmx-ciu-defs.h b/arch/mips/include/asm/octeon/cvmx-ciu-defs.h
new file mode 100644
index 000000000..1d18be8cd
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-ciu-defs.h
@@ -0,0 +1,176 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Octeon CIU definitions
+ *
+ * Copyright (C) 2003-2018 Cavium, Inc.
+ */
+
+#ifndef __CVMX_CIU_DEFS_H__
+#define __CVMX_CIU_DEFS_H__
+
+#include <asm/bitfield.h>
+
+#define CVMX_CIU_ADDR(addr, coreid, coremask, offset)			       \
+	(CVMX_ADD_IO_SEG(0x0001070000000000ull + addr##ull) +		       \
+	(((coreid) & (coremask)) * offset))
+
+#define CVMX_CIU_EN2_PPX_IP4(c)		CVMX_CIU_ADDR(0xA400, c, 0x0F, 8)
+#define CVMX_CIU_EN2_PPX_IP4_W1C(c)	CVMX_CIU_ADDR(0xCC00, c, 0x0F, 8)
+#define CVMX_CIU_EN2_PPX_IP4_W1S(c)	CVMX_CIU_ADDR(0xAC00, c, 0x0F, 8)
+#define CVMX_CIU_FUSE			CVMX_CIU_ADDR(0x0728, 0, 0x00, 0)
+#define CVMX_CIU_INT_SUM1		CVMX_CIU_ADDR(0x0108, 0, 0x00, 0)
+#define CVMX_CIU_INTX_EN0(c)		CVMX_CIU_ADDR(0x0200, c, 0x3F, 16)
+#define CVMX_CIU_INTX_EN0_W1C(c)	CVMX_CIU_ADDR(0x2200, c, 0x3F, 16)
+#define CVMX_CIU_INTX_EN0_W1S(c)	CVMX_CIU_ADDR(0x6200, c, 0x3F, 16)
+#define CVMX_CIU_INTX_EN1(c)		CVMX_CIU_ADDR(0x0208, c, 0x3F, 16)
+#define CVMX_CIU_INTX_EN1_W1C(c)	CVMX_CIU_ADDR(0x2208, c, 0x3F, 16)
+#define CVMX_CIU_INTX_EN1_W1S(c)	CVMX_CIU_ADDR(0x6208, c, 0x3F, 16)
+#define CVMX_CIU_INTX_SUM0(c)		CVMX_CIU_ADDR(0x0000, c, 0x3F, 8)
+#define CVMX_CIU_NMI			CVMX_CIU_ADDR(0x0718, 0, 0x00, 0)
+#define CVMX_CIU_PCI_INTA		CVMX_CIU_ADDR(0x0750, 0, 0x00, 0)
+#define CVMX_CIU_PP_BIST_STAT		CVMX_CIU_ADDR(0x07E0, 0, 0x00, 0)
+#define CVMX_CIU_PP_DBG			CVMX_CIU_ADDR(0x0708, 0, 0x00, 0)
+#define CVMX_CIU_PP_RST			CVMX_CIU_ADDR(0x0700, 0, 0x00, 0)
+#define CVMX_CIU_QLM0			CVMX_CIU_ADDR(0x0780, 0, 0x00, 0)
+#define CVMX_CIU_QLM1			CVMX_CIU_ADDR(0x0788, 0, 0x00, 0)
+#define CVMX_CIU_QLM_JTGC		CVMX_CIU_ADDR(0x0768, 0, 0x00, 0)
+#define CVMX_CIU_QLM_JTGD		CVMX_CIU_ADDR(0x0770, 0, 0x00, 0)
+#define CVMX_CIU_SOFT_BIST		CVMX_CIU_ADDR(0x0738, 0, 0x00, 0)
+#define CVMX_CIU_SOFT_PRST1		CVMX_CIU_ADDR(0x0758, 0, 0x00, 0)
+#define CVMX_CIU_SOFT_PRST		CVMX_CIU_ADDR(0x0748, 0, 0x00, 0)
+#define CVMX_CIU_SOFT_RST		CVMX_CIU_ADDR(0x0740, 0, 0x00, 0)
+#define CVMX_CIU_SUM2_PPX_IP4(c)	CVMX_CIU_ADDR(0x8C00, c, 0x0F, 8)
+#define CVMX_CIU_TIM_MULTI_CAST		CVMX_CIU_ADDR(0xC200, 0, 0x00, 0)
+#define CVMX_CIU_TIMX(c)		CVMX_CIU_ADDR(0x0480, c, 0x0F, 8)
+
+static inline uint64_t CVMX_CIU_MBOX_CLRX(unsigned int coreid)
+{
+	if (cvmx_get_octeon_family() == (OCTEON_CN68XX & OCTEON_FAMILY_MASK))
+		return CVMX_CIU_ADDR(0x100100600, coreid, 0x0F, 8);
+	else
+		return CVMX_CIU_ADDR(0x000000680, coreid, 0x0F, 8);
+}
+
+static inline uint64_t CVMX_CIU_MBOX_SETX(unsigned int coreid)
+{
+	if (cvmx_get_octeon_family() == (OCTEON_CN68XX & OCTEON_FAMILY_MASK))
+		return CVMX_CIU_ADDR(0x100100400, coreid, 0x0F, 8);
+	else
+		return CVMX_CIU_ADDR(0x000000600, coreid, 0x0F, 8);
+}
+
+static inline uint64_t CVMX_CIU_PP_POKEX(unsigned int coreid)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_CIU_ADDR(0x100100200, coreid, 0x0F, 8);
+	case OCTEON_CNF75XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN73XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN78XX & OCTEON_FAMILY_MASK:
+		return CVMX_CIU_ADDR(0x000030000, coreid, 0x0F, 8) -
+			0x60000000000ull;
+	default:
+		return CVMX_CIU_ADDR(0x000000580, coreid, 0x0F, 8);
+	}
+}
+
+static inline uint64_t CVMX_CIU_WDOGX(unsigned int coreid)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_CIU_ADDR(0x100100000, coreid, 0x0F, 8);
+	case OCTEON_CNF75XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN73XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN78XX & OCTEON_FAMILY_MASK:
+		return CVMX_CIU_ADDR(0x000020000, coreid, 0x0F, 8) -
+			0x60000000000ull;
+	default:
+		return CVMX_CIU_ADDR(0x000000500, coreid, 0x0F, 8);
+	}
+}
+
+
+union cvmx_ciu_qlm {
+	uint64_t u64;
+	struct cvmx_ciu_qlm_s {
+		__BITFIELD_FIELD(uint64_t g2bypass:1,
+		__BITFIELD_FIELD(uint64_t reserved_53_62:10,
+		__BITFIELD_FIELD(uint64_t g2deemph:5,
+		__BITFIELD_FIELD(uint64_t reserved_45_47:3,
+		__BITFIELD_FIELD(uint64_t g2margin:5,
+		__BITFIELD_FIELD(uint64_t reserved_32_39:8,
+		__BITFIELD_FIELD(uint64_t txbypass:1,
+		__BITFIELD_FIELD(uint64_t reserved_21_30:10,
+		__BITFIELD_FIELD(uint64_t txdeemph:5,
+		__BITFIELD_FIELD(uint64_t reserved_13_15:3,
+		__BITFIELD_FIELD(uint64_t txmargin:5,
+		__BITFIELD_FIELD(uint64_t reserved_4_7:4,
+		__BITFIELD_FIELD(uint64_t lane_en:4,
+		;)))))))))))))
+	} s;
+};
+
+union cvmx_ciu_qlm_jtgc {
+	uint64_t u64;
+	struct cvmx_ciu_qlm_jtgc_s {
+		__BITFIELD_FIELD(uint64_t reserved_17_63:47,
+		__BITFIELD_FIELD(uint64_t bypass_ext:1,
+		__BITFIELD_FIELD(uint64_t reserved_11_15:5,
+		__BITFIELD_FIELD(uint64_t clk_div:3,
+		__BITFIELD_FIELD(uint64_t reserved_7_7:1,
+		__BITFIELD_FIELD(uint64_t mux_sel:3,
+		__BITFIELD_FIELD(uint64_t bypass:4,
+		;)))))))
+	} s;
+};
+
+union cvmx_ciu_qlm_jtgd {
+	uint64_t u64;
+	struct cvmx_ciu_qlm_jtgd_s {
+		__BITFIELD_FIELD(uint64_t capture:1,
+		__BITFIELD_FIELD(uint64_t shift:1,
+		__BITFIELD_FIELD(uint64_t update:1,
+		__BITFIELD_FIELD(uint64_t reserved_45_60:16,
+		__BITFIELD_FIELD(uint64_t select:5,
+		__BITFIELD_FIELD(uint64_t reserved_37_39:3,
+		__BITFIELD_FIELD(uint64_t shft_cnt:5,
+		__BITFIELD_FIELD(uint64_t shft_reg:32,
+		;))))))))
+	} s;
+};
+
+union cvmx_ciu_soft_prst {
+	uint64_t u64;
+	struct cvmx_ciu_soft_prst_s {
+		__BITFIELD_FIELD(uint64_t reserved_3_63:61,
+		__BITFIELD_FIELD(uint64_t host64:1,
+		__BITFIELD_FIELD(uint64_t npi:1,
+		__BITFIELD_FIELD(uint64_t soft_prst:1,
+		;))))
+	} s;
+};
+
+union cvmx_ciu_timx {
+	uint64_t u64;
+	struct cvmx_ciu_timx_s {
+		__BITFIELD_FIELD(uint64_t reserved_37_63:27,
+		__BITFIELD_FIELD(uint64_t one_shot:1,
+		__BITFIELD_FIELD(uint64_t len:36,
+		;)))
+	} s;
+};
+
+union cvmx_ciu_wdogx {
+	uint64_t u64;
+	struct cvmx_ciu_wdogx_s {
+		__BITFIELD_FIELD(uint64_t reserved_46_63:18,
+		__BITFIELD_FIELD(uint64_t gstopen:1,
+		__BITFIELD_FIELD(uint64_t dstop:1,
+		__BITFIELD_FIELD(uint64_t cnt:24,
+		__BITFIELD_FIELD(uint64_t len:16,
+		__BITFIELD_FIELD(uint64_t state:2,
+		__BITFIELD_FIELD(uint64_t mode:2,
+		;)))))))
+	} s;
+};
+
+#endif /* __CVMX_CIU_DEFS_H__ */
diff --git a/arch/mips/include/asm/octeon/cvmx-ciu2-defs.h b/arch/mips/include/asm/octeon/cvmx-ciu2-defs.h
new file mode 100644
index 000000000..5babd88d4
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-ciu2-defs.h
@@ -0,0 +1,48 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2012 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_CIU2_DEFS_H__
+#define __CVMX_CIU2_DEFS_H__
+
+#define CVMX_CIU2_ACK_PPX_IP2(block_id) (CVMX_ADD_IO_SEG(0x00010701000C0000ull) + ((block_id) & 31) * 0x200000ull)
+#define CVMX_CIU2_ACK_PPX_IP3(block_id) (CVMX_ADD_IO_SEG(0x00010701000C0200ull) + ((block_id) & 31) * 0x200000ull)
+#define CVMX_CIU2_EN_PPX_IP2_RML(block_id) (CVMX_ADD_IO_SEG(0x0001070100092000ull) + ((block_id) & 31) * 0x200000ull)
+#define CVMX_CIU2_EN_PPX_IP2_WDOG(block_id) (CVMX_ADD_IO_SEG(0x0001070100091000ull) + ((block_id) & 31) * 0x200000ull)
+#define CVMX_CIU2_EN_PPX_IP2_WRKQ(block_id) (CVMX_ADD_IO_SEG(0x0001070100090000ull) + ((block_id) & 31) * 0x200000ull)
+#define CVMX_CIU2_EN_PPX_IP2_WRKQ_W1C(block_id) (CVMX_ADD_IO_SEG(0x00010701000B0000ull) + ((block_id) & 31) * 0x200000ull)
+#define CVMX_CIU2_EN_PPX_IP2_WRKQ_W1S(block_id) (CVMX_ADD_IO_SEG(0x00010701000A0000ull) + ((block_id) & 31) * 0x200000ull)
+#define CVMX_CIU2_EN_PPX_IP3_MBOX_W1C(block_id) (CVMX_ADD_IO_SEG(0x00010701000B8200ull) + ((block_id) & 31) * 0x200000ull)
+#define CVMX_CIU2_EN_PPX_IP3_MBOX_W1S(block_id) (CVMX_ADD_IO_SEG(0x00010701000A8200ull) + ((block_id) & 31) * 0x200000ull)
+#define CVMX_CIU2_INTR_CIU_READY (CVMX_ADD_IO_SEG(0x0001070100102008ull))
+#define CVMX_CIU2_RAW_PPX_IP2_WRKQ(block_id) (CVMX_ADD_IO_SEG(0x0001070100040000ull) + ((block_id) & 31) * 0x200000ull)
+#define CVMX_CIU2_SRC_PPX_IP2_RML(block_id) (CVMX_ADD_IO_SEG(0x0001070100082000ull) + ((block_id) & 31) * 0x200000ull)
+#define CVMX_CIU2_SRC_PPX_IP2_WDOG(block_id) (CVMX_ADD_IO_SEG(0x0001070100081000ull) + ((block_id) & 31) * 0x200000ull)
+#define CVMX_CIU2_SRC_PPX_IP2_WRKQ(block_id) (CVMX_ADD_IO_SEG(0x0001070100080000ull) + ((block_id) & 31) * 0x200000ull)
+#define CVMX_CIU2_SUM_PPX_IP2(offset) (CVMX_ADD_IO_SEG(0x0001070100000000ull) + ((offset) & 31) * 8)
+#define CVMX_CIU2_SUM_PPX_IP3(offset) (CVMX_ADD_IO_SEG(0x0001070100000200ull) + ((offset) & 31) * 8)
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-ciu3-defs.h b/arch/mips/include/asm/octeon/cvmx-ciu3-defs.h
new file mode 100644
index 000000000..547f778f5
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-ciu3-defs.h
@@ -0,0 +1,353 @@
+/*
+ * Copyright (c) 2003-2016 Cavium Inc.
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ */
+
+#ifndef __CVMX_CIU3_DEFS_H__
+#define __CVMX_CIU3_DEFS_H__
+
+#define CVMX_CIU3_FUSE CVMX_ADD_IO_SEG(0x00010100000001A0ull)
+#define CVMX_CIU3_BIST CVMX_ADD_IO_SEG(0x00010100000001C0ull)
+#define CVMX_CIU3_CONST CVMX_ADD_IO_SEG(0x0001010000000220ull)
+#define CVMX_CIU3_CTL CVMX_ADD_IO_SEG(0x00010100000000E0ull)
+#define CVMX_CIU3_DESTX_IO_INT(offset) (CVMX_ADD_IO_SEG(0x0001010000210000ull) + ((offset) & 7) * 8)
+#define CVMX_CIU3_DESTX_PP_INT(offset) (CVMX_ADD_IO_SEG(0x0001010000200000ull) + ((offset) & 255) * 8)
+#define CVMX_CIU3_GSTOP CVMX_ADD_IO_SEG(0x0001010000000140ull)
+#define CVMX_CIU3_IDTX_CTL(offset) (CVMX_ADD_IO_SEG(0x0001010000110000ull) + ((offset) & 255) * 8)
+#define CVMX_CIU3_IDTX_IO(offset) (CVMX_ADD_IO_SEG(0x0001010000130000ull) + ((offset) & 255) * 8)
+#define CVMX_CIU3_IDTX_PPX(offset, block_id) (CVMX_ADD_IO_SEG(0x0001010000120000ull) + ((block_id) & 255) * 0x20ull)
+#define CVMX_CIU3_INTR_RAM_ECC_CTL CVMX_ADD_IO_SEG(0x0001010000000260ull)
+#define CVMX_CIU3_INTR_RAM_ECC_ST CVMX_ADD_IO_SEG(0x0001010000000280ull)
+#define CVMX_CIU3_INTR_READY CVMX_ADD_IO_SEG(0x00010100000002A0ull)
+#define CVMX_CIU3_INTR_SLOWDOWN CVMX_ADD_IO_SEG(0x0001010000000240ull)
+#define CVMX_CIU3_ISCX_CTL(offset) (CVMX_ADD_IO_SEG(0x0001010080000000ull) + ((offset) & 1048575) * 8)
+#define CVMX_CIU3_ISCX_W1C(offset) (CVMX_ADD_IO_SEG(0x0001010090000000ull) + ((offset) & 1048575) * 8)
+#define CVMX_CIU3_ISCX_W1S(offset) (CVMX_ADD_IO_SEG(0x00010100A0000000ull) + ((offset) & 1048575) * 8)
+#define CVMX_CIU3_NMI CVMX_ADD_IO_SEG(0x0001010000000160ull)
+#define CVMX_CIU3_SISCX(offset) (CVMX_ADD_IO_SEG(0x0001010000220000ull) + ((offset) & 255) * 8)
+#define CVMX_CIU3_TIMX(offset) (CVMX_ADD_IO_SEG(0x0001010000010000ull) + ((offset) & 15) * 8)
+
+union cvmx_ciu3_bist {
+	uint64_t u64;
+	struct cvmx_ciu3_bist_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+	uint64_t reserved_9_63                : 55;
+	uint64_t bist                         : 9;
+#else
+	uint64_t bist                         : 9;
+	uint64_t reserved_9_63                : 55;
+#endif
+	} s;
+};
+
+union cvmx_ciu3_const {
+	uint64_t u64;
+	struct cvmx_ciu3_const_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+	uint64_t dests_io                     : 16;
+	uint64_t pintsn                       : 16;
+	uint64_t dests_pp                     : 16;
+	uint64_t idt                          : 16;
+#else
+	uint64_t idt                          : 16;
+	uint64_t dests_pp                     : 16;
+	uint64_t pintsn                       : 16;
+	uint64_t dests_io                     : 16;
+#endif
+	} s;
+};
+
+union cvmx_ciu3_ctl {
+	uint64_t u64;
+	struct cvmx_ciu3_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+	uint64_t reserved_5_63                : 59;
+	uint64_t mcd_sel                      : 2;
+	uint64_t iscmem_le                    : 1;
+	uint64_t seq_dis                      : 1;
+	uint64_t cclk_dis                     : 1;
+#else
+	uint64_t cclk_dis                     : 1;
+	uint64_t seq_dis                      : 1;
+	uint64_t iscmem_le                    : 1;
+	uint64_t mcd_sel                      : 2;
+	uint64_t reserved_5_63                : 59;
+#endif
+	} s;
+};
+
+union cvmx_ciu3_destx_io_int {
+	uint64_t u64;
+	struct cvmx_ciu3_destx_io_int_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+	uint64_t reserved_52_63               : 12;
+	uint64_t intsn                        : 20;
+	uint64_t reserved_10_31               : 22;
+	uint64_t intidt                       : 8;
+	uint64_t newint                       : 1;
+	uint64_t intr                         : 1;
+#else
+	uint64_t intr                         : 1;
+	uint64_t newint                       : 1;
+	uint64_t intidt                       : 8;
+	uint64_t reserved_10_31               : 22;
+	uint64_t intsn                        : 20;
+	uint64_t reserved_52_63               : 12;
+#endif
+	} s;
+};
+
+union cvmx_ciu3_destx_pp_int {
+	uint64_t u64;
+	struct cvmx_ciu3_destx_pp_int_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+	uint64_t reserved_52_63               : 12;
+	uint64_t intsn                        : 20;
+	uint64_t reserved_10_31               : 22;
+	uint64_t intidt                       : 8;
+	uint64_t newint                       : 1;
+	uint64_t intr                         : 1;
+#else
+	uint64_t intr                         : 1;
+	uint64_t newint                       : 1;
+	uint64_t intidt                       : 8;
+	uint64_t reserved_10_31               : 22;
+	uint64_t intsn                        : 20;
+	uint64_t reserved_52_63               : 12;
+#endif
+	} s;
+};
+
+union cvmx_ciu3_gstop {
+	uint64_t u64;
+	struct cvmx_ciu3_gstop_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+	uint64_t reserved_1_63                : 63;
+	uint64_t gstop                        : 1;
+#else
+	uint64_t gstop                        : 1;
+	uint64_t reserved_1_63                : 63;
+#endif
+	} s;
+};
+
+union cvmx_ciu3_idtx_ctl {
+	uint64_t u64;
+	struct cvmx_ciu3_idtx_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+	uint64_t reserved_52_63               : 12;
+	uint64_t intsn                        : 20;
+	uint64_t reserved_4_31                : 28;
+	uint64_t intr                         : 1;
+	uint64_t newint                       : 1;
+	uint64_t ip_num                       : 2;
+#else
+	uint64_t ip_num                       : 2;
+	uint64_t newint                       : 1;
+	uint64_t intr                         : 1;
+	uint64_t reserved_4_31                : 28;
+	uint64_t intsn                        : 20;
+	uint64_t reserved_52_63               : 12;
+#endif
+	} s;
+};
+
+union cvmx_ciu3_idtx_io {
+	uint64_t u64;
+	struct cvmx_ciu3_idtx_io_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+	uint64_t reserved_5_63                : 59;
+	uint64_t io                           : 5;
+#else
+	uint64_t io                           : 5;
+	uint64_t reserved_5_63                : 59;
+#endif
+	} s;
+};
+
+union cvmx_ciu3_idtx_ppx {
+	uint64_t u64;
+	struct cvmx_ciu3_idtx_ppx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+	uint64_t reserved_48_63               : 16;
+	uint64_t pp                           : 48;
+#else
+	uint64_t pp                           : 48;
+	uint64_t reserved_48_63               : 16;
+#endif
+	} s;
+};
+
+union cvmx_ciu3_intr_ram_ecc_ctl {
+	uint64_t u64;
+	struct cvmx_ciu3_intr_ram_ecc_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+	uint64_t reserved_3_63                : 61;
+	uint64_t flip_synd                    : 2;
+	uint64_t ecc_ena                      : 1;
+#else
+	uint64_t ecc_ena                      : 1;
+	uint64_t flip_synd                    : 2;
+	uint64_t reserved_3_63                : 61;
+#endif
+	} s;
+};
+
+union cvmx_ciu3_intr_ram_ecc_st {
+	uint64_t u64;
+	struct cvmx_ciu3_intr_ram_ecc_st_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+	uint64_t reserved_52_63               : 12;
+	uint64_t addr                         : 20;
+	uint64_t reserved_6_31                : 26;
+	uint64_t sisc_dbe                     : 1;
+	uint64_t sisc_sbe                     : 1;
+	uint64_t idt_dbe                      : 1;
+	uint64_t idt_sbe                      : 1;
+	uint64_t isc_dbe                      : 1;
+	uint64_t isc_sbe                      : 1;
+#else
+	uint64_t isc_sbe                      : 1;
+	uint64_t isc_dbe                      : 1;
+	uint64_t idt_sbe                      : 1;
+	uint64_t idt_dbe                      : 1;
+	uint64_t sisc_sbe                     : 1;
+	uint64_t sisc_dbe                     : 1;
+	uint64_t reserved_6_31                : 26;
+	uint64_t addr                         : 20;
+	uint64_t reserved_52_63               : 12;
+#endif
+	} s;
+};
+
+union cvmx_ciu3_intr_ready {
+	uint64_t u64;
+	struct cvmx_ciu3_intr_ready_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+	uint64_t reserved_46_63               : 18;
+	uint64_t index                        : 14;
+	uint64_t reserved_1_31                : 31;
+	uint64_t ready                        : 1;
+#else
+	uint64_t ready                        : 1;
+	uint64_t reserved_1_31                : 31;
+	uint64_t index                        : 14;
+	uint64_t reserved_46_63               : 18;
+#endif
+	} s;
+};
+
+union cvmx_ciu3_intr_slowdown {
+	uint64_t u64;
+	struct cvmx_ciu3_intr_slowdown_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+	uint64_t reserved_3_63                : 61;
+	uint64_t ctl                          : 3;
+#else
+	uint64_t ctl                          : 3;
+	uint64_t reserved_3_63                : 61;
+#endif
+	} s;
+};
+
+union cvmx_ciu3_iscx_ctl {
+	uint64_t u64;
+	struct cvmx_ciu3_iscx_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+	uint64_t reserved_24_63               : 40;
+	uint64_t idt                          : 8;
+	uint64_t imp                          : 1;
+	uint64_t reserved_2_14                : 13;
+	uint64_t en                           : 1;
+	uint64_t raw                          : 1;
+#else
+	uint64_t raw                          : 1;
+	uint64_t en                           : 1;
+	uint64_t reserved_2_14                : 13;
+	uint64_t imp                          : 1;
+	uint64_t idt                          : 8;
+	uint64_t reserved_24_63               : 40;
+#endif
+	} s;
+};
+
+union cvmx_ciu3_iscx_w1c {
+	uint64_t u64;
+	struct cvmx_ciu3_iscx_w1c_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+	uint64_t reserved_2_63                : 62;
+	uint64_t en                           : 1;
+	uint64_t raw                          : 1;
+#else
+	uint64_t raw                          : 1;
+	uint64_t en                           : 1;
+	uint64_t reserved_2_63                : 62;
+#endif
+	} s;
+};
+
+union cvmx_ciu3_iscx_w1s {
+	uint64_t u64;
+	struct cvmx_ciu3_iscx_w1s_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+	uint64_t reserved_2_63                : 62;
+	uint64_t en                           : 1;
+	uint64_t raw                          : 1;
+#else
+	uint64_t raw                          : 1;
+	uint64_t en                           : 1;
+	uint64_t reserved_2_63                : 62;
+#endif
+	} s;
+};
+
+union cvmx_ciu3_nmi {
+	uint64_t u64;
+	struct cvmx_ciu3_nmi_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+	uint64_t reserved_48_63               : 16;
+	uint64_t nmi                          : 48;
+#else
+	uint64_t nmi                          : 48;
+	uint64_t reserved_48_63               : 16;
+#endif
+	} s;
+};
+
+union cvmx_ciu3_siscx {
+	uint64_t u64;
+	struct cvmx_ciu3_siscx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+	uint64_t en                           : 64;
+#else
+	uint64_t en                           : 64;
+#endif
+	} s;
+};
+
+union cvmx_ciu3_timx {
+	uint64_t u64;
+	struct cvmx_ciu3_timx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+	uint64_t reserved_37_63               : 27;
+	uint64_t one_shot                     : 1;
+	uint64_t len                          : 36;
+#else
+	uint64_t len                          : 36;
+	uint64_t one_shot                     : 1;
+	uint64_t reserved_37_63               : 27;
+#endif
+	} s;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-cmd-queue.h b/arch/mips/include/asm/octeon/cvmx-cmd-queue.h
new file mode 100644
index 000000000..a07a36f7d
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-cmd-queue.h
@@ -0,0 +1,619 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ *
+ * Support functions for managing command queues used for
+ * various hardware blocks.
+ *
+ * The common command queue infrastructure abstracts out the
+ * software necessary for adding to Octeon's chained queue
+ * structures. These structures are used for commands to the
+ * PKO, ZIP, DFA, RAID, and DMA engine blocks. Although each
+ * hardware unit takes commands and CSRs of different types,
+ * they all use basic linked command buffers to store the
+ * pending request. In general, users of the CVMX API don't
+ * call cvmx-cmd-queue functions directly. Instead the hardware
+ * unit specific wrapper should be used. The wrappers perform
+ * unit specific validation and CSR writes to submit the
+ * commands.
+ *
+ * Even though most software will never directly interact with
+ * cvmx-cmd-queue, knowledge of its internal working can help
+ * in diagnosing performance problems and help with debugging.
+ *
+ * Command queue pointers are stored in a global named block
+ * called "cvmx_cmd_queues". Except for the PKO queues, each
+ * hardware queue is stored in its own cache line to reduce SMP
+ * contention on spin locks. The PKO queues are stored such that
+ * every 16th queue is next to each other in memory. This scheme
+ * allows for queues being in separate cache lines when there
+ * are low number of queues per port. With 16 queues per port,
+ * the first queue for each port is in the same cache area. The
+ * second queues for each port are in another area, etc. This
+ * allows software to implement very efficient lockless PKO with
+ * 16 queues per port using a minimum of cache lines per core.
+ * All queues for a given core will be isolated in the same
+ * cache area.
+ *
+ * In addition to the memory pointer layout, cvmx-cmd-queue
+ * provides an optimized fair ll/sc locking mechanism for the
+ * queues. The lock uses a "ticket / now serving" model to
+ * maintain fair order on contended locks. In addition, it uses
+ * predicted locking time to limit cache contention. When a core
+ * know it must wait in line for a lock, it spins on the
+ * internal cycle counter to completely eliminate any causes of
+ * bus traffic.
+ *
+ */
+
+#ifndef __CVMX_CMD_QUEUE_H__
+#define __CVMX_CMD_QUEUE_H__
+
+#include <linux/prefetch.h>
+
+#include <asm/compiler.h>
+
+#include <asm/octeon/cvmx-fpa.h>
+/**
+ * By default we disable the max depth support. Most programs
+ * don't use it and it slows down the command queue processing
+ * significantly.
+ */
+#ifndef CVMX_CMD_QUEUE_ENABLE_MAX_DEPTH
+#define CVMX_CMD_QUEUE_ENABLE_MAX_DEPTH 0
+#endif
+
+/**
+ * Enumeration representing all hardware blocks that use command
+ * queues. Each hardware block has up to 65536 sub identifiers for
+ * multiple command queues. Not all chips support all hardware
+ * units.
+ */
+typedef enum {
+	CVMX_CMD_QUEUE_PKO_BASE = 0x00000,
+
+#define CVMX_CMD_QUEUE_PKO(queue) \
+	((cvmx_cmd_queue_id_t)(CVMX_CMD_QUEUE_PKO_BASE + (0xffff&(queue))))
+
+	CVMX_CMD_QUEUE_ZIP = 0x10000,
+	CVMX_CMD_QUEUE_DFA = 0x20000,
+	CVMX_CMD_QUEUE_RAID = 0x30000,
+	CVMX_CMD_QUEUE_DMA_BASE = 0x40000,
+
+#define CVMX_CMD_QUEUE_DMA(queue) \
+	((cvmx_cmd_queue_id_t)(CVMX_CMD_QUEUE_DMA_BASE + (0xffff&(queue))))
+
+	CVMX_CMD_QUEUE_END = 0x50000,
+} cvmx_cmd_queue_id_t;
+
+/**
+ * Command write operations can fail if the command queue needs
+ * a new buffer and the associated FPA pool is empty. It can also
+ * fail if the number of queued command words reaches the maximum
+ * set at initialization.
+ */
+typedef enum {
+	CVMX_CMD_QUEUE_SUCCESS = 0,
+	CVMX_CMD_QUEUE_NO_MEMORY = -1,
+	CVMX_CMD_QUEUE_FULL = -2,
+	CVMX_CMD_QUEUE_INVALID_PARAM = -3,
+	CVMX_CMD_QUEUE_ALREADY_SETUP = -4,
+} cvmx_cmd_queue_result_t;
+
+typedef struct {
+	/* You have lock when this is your ticket */
+	uint8_t now_serving;
+	uint64_t unused1:24;
+	/* Maximum outstanding command words */
+	uint32_t max_depth;
+	/* FPA pool buffers come from */
+	uint64_t fpa_pool:3;
+	/* Top of command buffer pointer shifted 7 */
+	uint64_t base_ptr_div128:29;
+	uint64_t unused2:6;
+	/* FPA buffer size in 64bit words minus 1 */
+	uint64_t pool_size_m1:13;
+	/* Number of commands already used in buffer */
+	uint64_t index:13;
+} __cvmx_cmd_queue_state_t;
+
+/**
+ * This structure contains the global state of all command queues.
+ * It is stored in a bootmem named block and shared by all
+ * applications running on Octeon. Tickets are stored in a differnet
+ * cache line that queue information to reduce the contention on the
+ * ll/sc used to get a ticket. If this is not the case, the update
+ * of queue state causes the ll/sc to fail quite often.
+ */
+typedef struct {
+	uint64_t ticket[(CVMX_CMD_QUEUE_END >> 16) * 256];
+	__cvmx_cmd_queue_state_t state[(CVMX_CMD_QUEUE_END >> 16) * 256];
+} __cvmx_cmd_queue_all_state_t;
+
+/**
+ * Initialize a command queue for use. The initial FPA buffer is
+ * allocated and the hardware unit is configured to point to the
+ * new command queue.
+ *
+ * @queue_id:  Hardware command queue to initialize.
+ * @max_depth: Maximum outstanding commands that can be queued.
+ * @fpa_pool:  FPA pool the command queues should come from.
+ * @pool_size: Size of each buffer in the FPA pool (bytes)
+ *
+ * Returns CVMX_CMD_QUEUE_SUCCESS or a failure code
+ */
+cvmx_cmd_queue_result_t cvmx_cmd_queue_initialize(cvmx_cmd_queue_id_t queue_id,
+						  int max_depth, int fpa_pool,
+						  int pool_size);
+
+/**
+ * Shutdown a queue a free it's command buffers to the FPA. The
+ * hardware connected to the queue must be stopped before this
+ * function is called.
+ *
+ * @queue_id: Queue to shutdown
+ *
+ * Returns CVMX_CMD_QUEUE_SUCCESS or a failure code
+ */
+cvmx_cmd_queue_result_t cvmx_cmd_queue_shutdown(cvmx_cmd_queue_id_t queue_id);
+
+/**
+ * Return the number of command words pending in the queue. This
+ * function may be relatively slow for some hardware units.
+ *
+ * @queue_id: Hardware command queue to query
+ *
+ * Returns Number of outstanding commands
+ */
+int cvmx_cmd_queue_length(cvmx_cmd_queue_id_t queue_id);
+
+/**
+ * Return the command buffer to be written to. The purpose of this
+ * function is to allow CVMX routine access t othe low level buffer
+ * for initial hardware setup. User applications should not call this
+ * function directly.
+ *
+ * @queue_id: Command queue to query
+ *
+ * Returns Command buffer or NULL on failure
+ */
+void *cvmx_cmd_queue_buffer(cvmx_cmd_queue_id_t queue_id);
+
+/**
+ * Get the index into the state arrays for the supplied queue id.
+ *
+ * @queue_id: Queue ID to get an index for
+ *
+ * Returns Index into the state arrays
+ */
+static inline int __cvmx_cmd_queue_get_index(cvmx_cmd_queue_id_t queue_id)
+{
+	/*
+	 * Warning: This code currently only works with devices that
+	 * have 256 queues or less. Devices with more than 16 queues
+	 * are laid out in memory to allow cores quick access to
+	 * every 16th queue. This reduces cache thrashing when you are
+	 * running 16 queues per port to support lockless operation.
+	 */
+	int unit = queue_id >> 16;
+	int q = (queue_id >> 4) & 0xf;
+	int core = queue_id & 0xf;
+	return unit * 256 + core * 16 + q;
+}
+
+/**
+ * Lock the supplied queue so nobody else is updating it at the same
+ * time as us.
+ *
+ * @queue_id: Queue ID to lock
+ * @qptr:     Pointer to the queue's global state
+ */
+static inline void __cvmx_cmd_queue_lock(cvmx_cmd_queue_id_t queue_id,
+					 __cvmx_cmd_queue_state_t *qptr)
+{
+	extern __cvmx_cmd_queue_all_state_t
+	    *__cvmx_cmd_queue_state_ptr;
+	int tmp;
+	int my_ticket;
+	prefetch(qptr);
+	asm volatile (
+		".set push\n"
+		".set noreorder\n"
+		"1:\n"
+		/* Atomic add one to ticket_ptr */
+		"ll	%[my_ticket], %[ticket_ptr]\n"
+		/* and store the original value */
+		"li	%[ticket], 1\n"
+		/* in my_ticket */
+		"baddu	%[ticket], %[my_ticket]\n"
+		"sc	%[ticket], %[ticket_ptr]\n"
+		"beqz	%[ticket], 1b\n"
+		" nop\n"
+		/* Load the current now_serving ticket */
+		"lbu	%[ticket], %[now_serving]\n"
+		"2:\n"
+		/* Jump out if now_serving == my_ticket */
+		"beq	%[ticket], %[my_ticket], 4f\n"
+		/* Find out how many tickets are in front of me */
+		" subu	 %[ticket], %[my_ticket], %[ticket]\n"
+		/* Use tickets in front of me minus one to delay */
+		"subu  %[ticket], 1\n"
+		/* Delay will be ((tickets in front)-1)*32 loops */
+		"cins	%[ticket], %[ticket], 5, 7\n"
+		"3:\n"
+		/* Loop here until our ticket might be up */
+		"bnez	%[ticket], 3b\n"
+		" subu	%[ticket], 1\n"
+		/* Jump back up to check out ticket again */
+		"b	2b\n"
+		/* Load the current now_serving ticket */
+		" lbu	%[ticket], %[now_serving]\n"
+		"4:\n"
+		".set pop\n" :
+		[ticket_ptr] "=" GCC_OFF_SMALL_ASM()(__cvmx_cmd_queue_state_ptr->ticket[__cvmx_cmd_queue_get_index(queue_id)]),
+		[now_serving] "=m"(qptr->now_serving), [ticket] "=r"(tmp),
+		[my_ticket] "=r"(my_ticket)
+	    );
+}
+
+/**
+ * Unlock the queue, flushing all writes.
+ *
+ * @qptr:   Queue to unlock
+ */
+static inline void __cvmx_cmd_queue_unlock(__cvmx_cmd_queue_state_t *qptr)
+{
+	qptr->now_serving++;
+	CVMX_SYNCWS;
+}
+
+/**
+ * Get the queue state structure for the given queue id
+ *
+ * @queue_id: Queue id to get
+ *
+ * Returns Queue structure or NULL on failure
+ */
+static inline __cvmx_cmd_queue_state_t
+    *__cvmx_cmd_queue_get_state(cvmx_cmd_queue_id_t queue_id)
+{
+	extern __cvmx_cmd_queue_all_state_t
+	    *__cvmx_cmd_queue_state_ptr;
+	return &__cvmx_cmd_queue_state_ptr->
+	    state[__cvmx_cmd_queue_get_index(queue_id)];
+}
+
+/**
+ * Write an arbitrary number of command words to a command queue.
+ * This is a generic function; the fixed number of command word
+ * functions yield higher performance.
+ *
+ * @queue_id:  Hardware command queue to write to
+ * @use_locking:
+ *		    Use internal locking to ensure exclusive access for queue
+ *		    updates. If you don't use this locking you must ensure
+ *		    exclusivity some other way. Locking is strongly recommended.
+ * @cmd_count: Number of command words to write
+ * @cmds:      Array of commands to write
+ *
+ * Returns CVMX_CMD_QUEUE_SUCCESS or a failure code
+ */
+static inline cvmx_cmd_queue_result_t cvmx_cmd_queue_write(cvmx_cmd_queue_id_t
+							   queue_id,
+							   int use_locking,
+							   int cmd_count,
+							   uint64_t *cmds)
+{
+	__cvmx_cmd_queue_state_t *qptr = __cvmx_cmd_queue_get_state(queue_id);
+
+	/* Make sure nobody else is updating the same queue */
+	if (likely(use_locking))
+		__cvmx_cmd_queue_lock(queue_id, qptr);
+
+	/*
+	 * If a max queue length was specified then make sure we don't
+	 * exceed it. If any part of the command would be below the
+	 * limit we allow it.
+	 */
+	if (CVMX_CMD_QUEUE_ENABLE_MAX_DEPTH && unlikely(qptr->max_depth)) {
+		if (unlikely
+		    (cvmx_cmd_queue_length(queue_id) > (int)qptr->max_depth)) {
+			if (likely(use_locking))
+				__cvmx_cmd_queue_unlock(qptr);
+			return CVMX_CMD_QUEUE_FULL;
+		}
+	}
+
+	/*
+	 * Normally there is plenty of room in the current buffer for
+	 * the command.
+	 */
+	if (likely(qptr->index + cmd_count < qptr->pool_size_m1)) {
+		uint64_t *ptr =
+		    (uint64_t *) cvmx_phys_to_ptr((uint64_t) qptr->
+						  base_ptr_div128 << 7);
+		ptr += qptr->index;
+		qptr->index += cmd_count;
+		while (cmd_count--)
+			*ptr++ = *cmds++;
+	} else {
+		uint64_t *ptr;
+		int count;
+		/*
+		 * We need a new command buffer. Fail if there isn't
+		 * one available.
+		 */
+		uint64_t *new_buffer =
+		    (uint64_t *) cvmx_fpa_alloc(qptr->fpa_pool);
+		if (unlikely(new_buffer == NULL)) {
+			if (likely(use_locking))
+				__cvmx_cmd_queue_unlock(qptr);
+			return CVMX_CMD_QUEUE_NO_MEMORY;
+		}
+		ptr =
+		    (uint64_t *) cvmx_phys_to_ptr((uint64_t) qptr->
+						  base_ptr_div128 << 7);
+		/*
+		 * Figure out how many command words will fit in this
+		 * buffer. One location will be needed for the next
+		 * buffer pointer.
+		 */
+		count = qptr->pool_size_m1 - qptr->index;
+		ptr += qptr->index;
+		cmd_count -= count;
+		while (count--)
+			*ptr++ = *cmds++;
+		*ptr = cvmx_ptr_to_phys(new_buffer);
+		/*
+		 * The current buffer is full and has a link to the
+		 * next buffer. Time to write the rest of the commands
+		 * into the new buffer.
+		 */
+		qptr->base_ptr_div128 = *ptr >> 7;
+		qptr->index = cmd_count;
+		ptr = new_buffer;
+		while (cmd_count--)
+			*ptr++ = *cmds++;
+	}
+
+	/* All updates are complete. Release the lock and return */
+	if (likely(use_locking))
+		__cvmx_cmd_queue_unlock(qptr);
+	return CVMX_CMD_QUEUE_SUCCESS;
+}
+
+/**
+ * Simple function to write two command words to a command
+ * queue.
+ *
+ * @queue_id: Hardware command queue to write to
+ * @use_locking:
+ *		   Use internal locking to ensure exclusive access for queue
+ *		   updates. If you don't use this locking you must ensure
+ *		   exclusivity some other way. Locking is strongly recommended.
+ * @cmd1:     Command
+ * @cmd2:     Command
+ *
+ * Returns CVMX_CMD_QUEUE_SUCCESS or a failure code
+ */
+static inline cvmx_cmd_queue_result_t cvmx_cmd_queue_write2(cvmx_cmd_queue_id_t
+							    queue_id,
+							    int use_locking,
+							    uint64_t cmd1,
+							    uint64_t cmd2)
+{
+	__cvmx_cmd_queue_state_t *qptr = __cvmx_cmd_queue_get_state(queue_id);
+
+	/* Make sure nobody else is updating the same queue */
+	if (likely(use_locking))
+		__cvmx_cmd_queue_lock(queue_id, qptr);
+
+	/*
+	 * If a max queue length was specified then make sure we don't
+	 * exceed it. If any part of the command would be below the
+	 * limit we allow it.
+	 */
+	if (CVMX_CMD_QUEUE_ENABLE_MAX_DEPTH && unlikely(qptr->max_depth)) {
+		if (unlikely
+		    (cvmx_cmd_queue_length(queue_id) > (int)qptr->max_depth)) {
+			if (likely(use_locking))
+				__cvmx_cmd_queue_unlock(qptr);
+			return CVMX_CMD_QUEUE_FULL;
+		}
+	}
+
+	/*
+	 * Normally there is plenty of room in the current buffer for
+	 * the command.
+	 */
+	if (likely(qptr->index + 2 < qptr->pool_size_m1)) {
+		uint64_t *ptr =
+		    (uint64_t *) cvmx_phys_to_ptr((uint64_t) qptr->
+						  base_ptr_div128 << 7);
+		ptr += qptr->index;
+		qptr->index += 2;
+		ptr[0] = cmd1;
+		ptr[1] = cmd2;
+	} else {
+		uint64_t *ptr;
+		/*
+		 * Figure out how many command words will fit in this
+		 * buffer. One location will be needed for the next
+		 * buffer pointer.
+		 */
+		int count = qptr->pool_size_m1 - qptr->index;
+		/*
+		 * We need a new command buffer. Fail if there isn't
+		 * one available.
+		 */
+		uint64_t *new_buffer =
+		    (uint64_t *) cvmx_fpa_alloc(qptr->fpa_pool);
+		if (unlikely(new_buffer == NULL)) {
+			if (likely(use_locking))
+				__cvmx_cmd_queue_unlock(qptr);
+			return CVMX_CMD_QUEUE_NO_MEMORY;
+		}
+		count--;
+		ptr =
+		    (uint64_t *) cvmx_phys_to_ptr((uint64_t) qptr->
+						  base_ptr_div128 << 7);
+		ptr += qptr->index;
+		*ptr++ = cmd1;
+		if (likely(count))
+			*ptr++ = cmd2;
+		*ptr = cvmx_ptr_to_phys(new_buffer);
+		/*
+		 * The current buffer is full and has a link to the
+		 * next buffer. Time to write the rest of the commands
+		 * into the new buffer.
+		 */
+		qptr->base_ptr_div128 = *ptr >> 7;
+		qptr->index = 0;
+		if (unlikely(count == 0)) {
+			qptr->index = 1;
+			new_buffer[0] = cmd2;
+		}
+	}
+
+	/* All updates are complete. Release the lock and return */
+	if (likely(use_locking))
+		__cvmx_cmd_queue_unlock(qptr);
+	return CVMX_CMD_QUEUE_SUCCESS;
+}
+
+/**
+ * Simple function to write three command words to a command
+ * queue.
+ *
+ * @queue_id: Hardware command queue to write to
+ * @use_locking:
+ *		   Use internal locking to ensure exclusive access for queue
+ *		   updates. If you don't use this locking you must ensure
+ *		   exclusivity some other way. Locking is strongly recommended.
+ * @cmd1:     Command
+ * @cmd2:     Command
+ * @cmd3:     Command
+ *
+ * Returns CVMX_CMD_QUEUE_SUCCESS or a failure code
+ */
+static inline cvmx_cmd_queue_result_t cvmx_cmd_queue_write3(cvmx_cmd_queue_id_t
+							    queue_id,
+							    int use_locking,
+							    uint64_t cmd1,
+							    uint64_t cmd2,
+							    uint64_t cmd3)
+{
+	__cvmx_cmd_queue_state_t *qptr = __cvmx_cmd_queue_get_state(queue_id);
+
+	/* Make sure nobody else is updating the same queue */
+	if (likely(use_locking))
+		__cvmx_cmd_queue_lock(queue_id, qptr);
+
+	/*
+	 * If a max queue length was specified then make sure we don't
+	 * exceed it. If any part of the command would be below the
+	 * limit we allow it.
+	 */
+	if (CVMX_CMD_QUEUE_ENABLE_MAX_DEPTH && unlikely(qptr->max_depth)) {
+		if (unlikely
+		    (cvmx_cmd_queue_length(queue_id) > (int)qptr->max_depth)) {
+			if (likely(use_locking))
+				__cvmx_cmd_queue_unlock(qptr);
+			return CVMX_CMD_QUEUE_FULL;
+		}
+	}
+
+	/*
+	 * Normally there is plenty of room in the current buffer for
+	 * the command.
+	 */
+	if (likely(qptr->index + 3 < qptr->pool_size_m1)) {
+		uint64_t *ptr =
+		    (uint64_t *) cvmx_phys_to_ptr((uint64_t) qptr->
+						  base_ptr_div128 << 7);
+		ptr += qptr->index;
+		qptr->index += 3;
+		ptr[0] = cmd1;
+		ptr[1] = cmd2;
+		ptr[2] = cmd3;
+	} else {
+		uint64_t *ptr;
+		/*
+		 * Figure out how many command words will fit in this
+		 * buffer. One location will be needed for the next
+		 * buffer pointer
+		 */
+		int count = qptr->pool_size_m1 - qptr->index;
+		/*
+		 * We need a new command buffer. Fail if there isn't
+		 * one available
+		 */
+		uint64_t *new_buffer =
+		    (uint64_t *) cvmx_fpa_alloc(qptr->fpa_pool);
+		if (unlikely(new_buffer == NULL)) {
+			if (likely(use_locking))
+				__cvmx_cmd_queue_unlock(qptr);
+			return CVMX_CMD_QUEUE_NO_MEMORY;
+		}
+		count--;
+		ptr =
+		    (uint64_t *) cvmx_phys_to_ptr((uint64_t) qptr->
+						  base_ptr_div128 << 7);
+		ptr += qptr->index;
+		*ptr++ = cmd1;
+		if (count) {
+			*ptr++ = cmd2;
+			if (count > 1)
+				*ptr++ = cmd3;
+		}
+		*ptr = cvmx_ptr_to_phys(new_buffer);
+		/*
+		 * The current buffer is full and has a link to the
+		 * next buffer. Time to write the rest of the commands
+		 * into the new buffer.
+		 */
+		qptr->base_ptr_div128 = *ptr >> 7;
+		qptr->index = 0;
+		ptr = new_buffer;
+		if (count == 0) {
+			*ptr++ = cmd2;
+			qptr->index++;
+		}
+		if (count < 2) {
+			*ptr++ = cmd3;
+			qptr->index++;
+		}
+	}
+
+	/* All updates are complete. Release the lock and return */
+	if (likely(use_locking))
+		__cvmx_cmd_queue_unlock(qptr);
+	return CVMX_CMD_QUEUE_SUCCESS;
+}
+
+#endif /* __CVMX_CMD_QUEUE_H__ */
diff --git a/arch/mips/include/asm/octeon/cvmx-config.h b/arch/mips/include/asm/octeon/cvmx-config.h
new file mode 100644
index 000000000..a8c358c02
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-config.h
@@ -0,0 +1,169 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __CVMX_CONFIG_H__
+#define __CVMX_CONFIG_H__
+
+/************************* Config Specific Defines ************************/
+#define CVMX_LLM_NUM_PORTS 1
+#define CVMX_NULL_POINTER_PROTECT 1
+#define CVMX_ENABLE_DEBUG_PRINTS 1
+/* PKO queues per port for interface 0 (ports 0-15) */
+#define CVMX_PKO_QUEUES_PER_PORT_INTERFACE0 1
+/* PKO queues per port for interface 1 (ports 16-31) */
+#define CVMX_PKO_QUEUES_PER_PORT_INTERFACE1 1
+/* Limit on the number of PKO ports enabled for interface 0 */
+#define CVMX_PKO_MAX_PORTS_INTERFACE0 CVMX_HELPER_PKO_MAX_PORTS_INTERFACE0
+/* Limit on the number of PKO ports enabled for interface 1 */
+#define CVMX_PKO_MAX_PORTS_INTERFACE1 CVMX_HELPER_PKO_MAX_PORTS_INTERFACE1
+/* PKO queues per port for PCI (ports 32-35) */
+#define CVMX_PKO_QUEUES_PER_PORT_PCI 1
+/* PKO queues per port for Loop devices (ports 36-39) */
+#define CVMX_PKO_QUEUES_PER_PORT_LOOP 1
+
+/************************* FPA allocation *********************************/
+/* Pool sizes in bytes, must be multiple of a cache line */
+#define CVMX_FPA_POOL_0_SIZE (16 * CVMX_CACHE_LINE_SIZE)
+#define CVMX_FPA_POOL_1_SIZE (1 * CVMX_CACHE_LINE_SIZE)
+#define CVMX_FPA_POOL_2_SIZE (8 * CVMX_CACHE_LINE_SIZE)
+#define CVMX_FPA_POOL_3_SIZE (0 * CVMX_CACHE_LINE_SIZE)
+#define CVMX_FPA_POOL_4_SIZE (0 * CVMX_CACHE_LINE_SIZE)
+#define CVMX_FPA_POOL_5_SIZE (0 * CVMX_CACHE_LINE_SIZE)
+#define CVMX_FPA_POOL_6_SIZE (0 * CVMX_CACHE_LINE_SIZE)
+#define CVMX_FPA_POOL_7_SIZE (0 * CVMX_CACHE_LINE_SIZE)
+
+/* Pools in use */
+/* Packet buffers */
+#define CVMX_FPA_PACKET_POOL		    (0)
+#define CVMX_FPA_PACKET_POOL_SIZE	    CVMX_FPA_POOL_0_SIZE
+/* Work queue entries */
+#define CVMX_FPA_WQE_POOL		    (1)
+#define CVMX_FPA_WQE_POOL_SIZE		    CVMX_FPA_POOL_1_SIZE
+/* PKO queue command buffers */
+#define CVMX_FPA_OUTPUT_BUFFER_POOL	    (2)
+#define CVMX_FPA_OUTPUT_BUFFER_POOL_SIZE    CVMX_FPA_POOL_2_SIZE
+
+/*************************  FAU allocation ********************************/
+/* The fetch and add registers are allocated here.  They are arranged
+ * in order of descending size so that all alignment constraints are
+ * automatically met.  The enums are linked so that the following enum
+ * continues allocating where the previous one left off, so the
+ * numbering within each enum always starts with zero.	The macros
+ * take care of the address increment size, so the values entered
+ * always increase by 1.  FAU registers are accessed with byte
+ * addresses.
+ */
+
+#define CVMX_FAU_REG_64_ADDR(x) ((x << 3) + CVMX_FAU_REG_64_START)
+typedef enum {
+	CVMX_FAU_REG_64_START	= 0,
+	CVMX_FAU_REG_64_END	= CVMX_FAU_REG_64_ADDR(0),
+} cvmx_fau_reg_64_t;
+
+#define CVMX_FAU_REG_32_ADDR(x) ((x << 2) + CVMX_FAU_REG_32_START)
+typedef enum {
+	CVMX_FAU_REG_32_START	= CVMX_FAU_REG_64_END,
+	CVMX_FAU_REG_32_END	= CVMX_FAU_REG_32_ADDR(0),
+} cvmx_fau_reg_32_t;
+
+#define CVMX_FAU_REG_16_ADDR(x) ((x << 1) + CVMX_FAU_REG_16_START)
+typedef enum {
+	CVMX_FAU_REG_16_START	= CVMX_FAU_REG_32_END,
+	CVMX_FAU_REG_16_END	= CVMX_FAU_REG_16_ADDR(0),
+} cvmx_fau_reg_16_t;
+
+#define CVMX_FAU_REG_8_ADDR(x) ((x) + CVMX_FAU_REG_8_START)
+typedef enum {
+	CVMX_FAU_REG_8_START	= CVMX_FAU_REG_16_END,
+	CVMX_FAU_REG_8_END	= CVMX_FAU_REG_8_ADDR(0),
+} cvmx_fau_reg_8_t;
+
+/*
+ * The name CVMX_FAU_REG_AVAIL_BASE is provided to indicate the first
+ * available FAU address that is not allocated in cvmx-config.h. This
+ * is 64 bit aligned.
+ */
+#define CVMX_FAU_REG_AVAIL_BASE ((CVMX_FAU_REG_8_END + 0x7) & (~0x7ULL))
+#define CVMX_FAU_REG_END (2048)
+
+/********************** scratch memory allocation *************************/
+/* Scratchpad memory allocation.  Note that these are byte memory
+ * addresses.  Some uses of scratchpad (IOBDMA for example) require
+ * the use of 8-byte aligned addresses, so proper alignment needs to
+ * be taken into account.
+ */
+/* Generic scratch iobdma area */
+#define CVMX_SCR_SCRATCH	       (0)
+/* First location available after cvmx-config.h allocated region. */
+#define CVMX_SCR_REG_AVAIL_BASE	       (8)
+
+/*
+ * CVMX_HELPER_FIRST_MBUFF_SKIP is the number of bytes to reserve
+ * before the beginning of the packet. If necessary, override the
+ * default here.  See the IPD section of the hardware manual for MBUFF
+ * SKIP details.
+ */
+#define CVMX_HELPER_FIRST_MBUFF_SKIP 184
+
+/*
+ * CVMX_HELPER_NOT_FIRST_MBUFF_SKIP is the number of bytes to reserve
+ * in each chained packet element. If necessary, override the default
+ * here.
+ */
+#define CVMX_HELPER_NOT_FIRST_MBUFF_SKIP 0
+
+/*
+ * CVMX_HELPER_ENABLE_BACK_PRESSURE controls whether back pressure is
+ * enabled for all input ports. This controls if IPD sends
+ * backpressure to all ports if Octeon's FPA pools don't have enough
+ * packet or work queue entries. Even when this is off, it is still
+ * possible to get backpressure from individual hardware ports. When
+ * configuring backpressure, also check
+ * CVMX_HELPER_DISABLE_*_BACKPRESSURE below. If necessary, override
+ * the default here.
+ */
+#define CVMX_HELPER_ENABLE_BACK_PRESSURE 1
+
+/*
+ * CVMX_HELPER_ENABLE_IPD controls if the IPD is enabled in the helper
+ * function. Once it is enabled the hardware starts accepting
+ * packets. You might want to skip the IPD enable if configuration
+ * changes are need from the default helper setup. If necessary,
+ * override the default here.
+ */
+#define CVMX_HELPER_ENABLE_IPD 0
+
+/*
+ * CVMX_HELPER_INPUT_TAG_TYPE selects the type of tag that the IPD assigns
+ * to incoming packets.
+ */
+#define CVMX_HELPER_INPUT_TAG_TYPE CVMX_POW_TAG_TYPE_ORDERED
+
+#define CVMX_ENABLE_PARAMETER_CHECKING 0
+
+/*
+ * The following select which fields are used by the PIP to generate
+ * the tag on INPUT
+ * 0: don't include
+ * 1: include
+ */
+#define CVMX_HELPER_INPUT_TAG_IPV6_SRC_IP	0
+#define CVMX_HELPER_INPUT_TAG_IPV6_DST_IP	0
+#define CVMX_HELPER_INPUT_TAG_IPV6_SRC_PORT	0
+#define CVMX_HELPER_INPUT_TAG_IPV6_DST_PORT	0
+#define CVMX_HELPER_INPUT_TAG_IPV6_NEXT_HEADER	0
+#define CVMX_HELPER_INPUT_TAG_IPV4_SRC_IP	0
+#define CVMX_HELPER_INPUT_TAG_IPV4_DST_IP	0
+#define CVMX_HELPER_INPUT_TAG_IPV4_SRC_PORT	0
+#define CVMX_HELPER_INPUT_TAG_IPV4_DST_PORT	0
+#define CVMX_HELPER_INPUT_TAG_IPV4_PROTOCOL	0
+#define CVMX_HELPER_INPUT_TAG_INPUT_PORT	1
+
+/* Select skip mode for input ports */
+#define CVMX_HELPER_INPUT_PORT_SKIP_MODE	CVMX_PIP_PORT_CFG_MODE_SKIPL2
+
+/*
+ * Force backpressure to be disabled.  This overrides all other
+ * backpressure configuration.
+ */
+#define CVMX_HELPER_DISABLE_RGMII_BACKPRESSURE 0
+
+#endif /* __CVMX_CONFIG_H__ */
diff --git a/arch/mips/include/asm/octeon/cvmx-coremask.h b/arch/mips/include/asm/octeon/cvmx-coremask.h
new file mode 100644
index 000000000..097dc096d
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-coremask.h
@@ -0,0 +1,89 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (c) 2016  Cavium Inc. (support@cavium.com).
+ *
+ */
+
+/*
+ * Module to support operations on bitmap of cores. Coremask can be used to
+ * select a specific core, a group of cores, or all available cores, for
+ * initialization and differentiation of roles within a single shared binary
+ * executable image.
+ *
+ * The core numbers used in this file are the same value as what is found in
+ * the COP0_EBASE register and the rdhwr 0 instruction.
+ *
+ * For the CN78XX and other multi-node environments the core numbers are not
+ * contiguous.  The core numbers for the CN78XX are as follows:
+ *
+ * Node 0:	Cores 0 - 47
+ * Node 1:	Cores 128 - 175
+ * Node 2:	Cores 256 - 303
+ * Node 3:	Cores 384 - 431
+ *
+ */
+
+#ifndef __CVMX_COREMASK_H__
+#define __CVMX_COREMASK_H__
+
+#define CVMX_MIPS_MAX_CORES 1024
+/* bits per holder */
+#define CVMX_COREMASK_ELTSZ 64
+
+/* cvmx_coremask_t's size in u64 */
+#define CVMX_COREMASK_BMPSZ (CVMX_MIPS_MAX_CORES / CVMX_COREMASK_ELTSZ)
+
+
+/* cvmx_coremask_t */
+struct cvmx_coremask {
+	u64 coremask_bitmap[CVMX_COREMASK_BMPSZ];
+};
+
+/*
+ * Is ``core'' set in the coremask?
+ */
+static inline bool cvmx_coremask_is_core_set(const struct cvmx_coremask *pcm,
+					    int core)
+{
+	int n, i;
+
+	n = core % CVMX_COREMASK_ELTSZ;
+	i = core / CVMX_COREMASK_ELTSZ;
+
+	return (pcm->coremask_bitmap[i] & ((u64)1 << n)) != 0;
+}
+
+/*
+ * Make a copy of a coremask
+ */
+static inline void cvmx_coremask_copy(struct cvmx_coremask *dest,
+				      const struct cvmx_coremask *src)
+{
+	memcpy(dest, src, sizeof(*dest));
+}
+
+/*
+ * Set the lower 64-bit of the coremask.
+ */
+static inline void cvmx_coremask_set64(struct cvmx_coremask *pcm,
+				       uint64_t coremask_64)
+{
+	pcm->coremask_bitmap[0] = coremask_64;
+}
+
+/*
+ * Clear ``core'' from the coremask.
+ */
+static inline void cvmx_coremask_clear_core(struct cvmx_coremask *pcm, int core)
+{
+	int n, i;
+
+	n = core % CVMX_COREMASK_ELTSZ;
+	i = core / CVMX_COREMASK_ELTSZ;
+	pcm->coremask_bitmap[i] &= ~(1ull << n);
+}
+
+#endif /* __CVMX_COREMASK_H__ */
diff --git a/arch/mips/include/asm/octeon/cvmx-dbg-defs.h b/arch/mips/include/asm/octeon/cvmx-dbg-defs.h
new file mode 100644
index 000000000..828d07d87
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-dbg-defs.h
@@ -0,0 +1,101 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2012 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_DBG_DEFS_H__
+#define __CVMX_DBG_DEFS_H__
+
+#define CVMX_DBG_DATA (CVMX_ADD_IO_SEG(0x00011F00000001E8ull))
+
+union cvmx_dbg_data {
+	uint64_t u64;
+	struct cvmx_dbg_data_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_23_63:41;
+		uint64_t c_mul:5;
+		uint64_t dsel_ext:1;
+		uint64_t data:17;
+#else
+		uint64_t data:17;
+		uint64_t dsel_ext:1;
+		uint64_t c_mul:5;
+		uint64_t reserved_23_63:41;
+#endif
+	} s;
+	struct cvmx_dbg_data_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_31_63:33;
+		uint64_t pll_mul:3;
+		uint64_t reserved_23_27:5;
+		uint64_t c_mul:5;
+		uint64_t dsel_ext:1;
+		uint64_t data:17;
+#else
+		uint64_t data:17;
+		uint64_t dsel_ext:1;
+		uint64_t c_mul:5;
+		uint64_t reserved_23_27:5;
+		uint64_t pll_mul:3;
+		uint64_t reserved_31_63:33;
+#endif
+	} cn30xx;
+	struct cvmx_dbg_data_cn38xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t d_mul:4;
+		uint64_t dclk_mul2:1;
+		uint64_t cclk_div2:1;
+		uint64_t c_mul:5;
+		uint64_t dsel_ext:1;
+		uint64_t data:17;
+#else
+		uint64_t data:17;
+		uint64_t dsel_ext:1;
+		uint64_t c_mul:5;
+		uint64_t cclk_div2:1;
+		uint64_t dclk_mul2:1;
+		uint64_t d_mul:4;
+		uint64_t reserved_29_63:35;
+#endif
+	} cn38xx;
+	struct cvmx_dbg_data_cn58xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t rem:6;
+		uint64_t c_mul:5;
+		uint64_t dsel_ext:1;
+		uint64_t data:17;
+#else
+		uint64_t data:17;
+		uint64_t dsel_ext:1;
+		uint64_t c_mul:5;
+		uint64_t rem:6;
+		uint64_t reserved_29_63:35;
+#endif
+	} cn58xx;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-dpi-defs.h b/arch/mips/include/asm/octeon/cvmx-dpi-defs.h
new file mode 100644
index 000000000..e8613e1f6
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-dpi-defs.h
@@ -0,0 +1,874 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2012 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_DPI_DEFS_H__
+#define __CVMX_DPI_DEFS_H__
+
+#define CVMX_DPI_BIST_STATUS (CVMX_ADD_IO_SEG(0x0001DF0000000000ull))
+#define CVMX_DPI_CTL (CVMX_ADD_IO_SEG(0x0001DF0000000040ull))
+#define CVMX_DPI_DMAX_COUNTS(offset) (CVMX_ADD_IO_SEG(0x0001DF0000000300ull) + ((offset) & 7) * 8)
+#define CVMX_DPI_DMAX_DBELL(offset) (CVMX_ADD_IO_SEG(0x0001DF0000000200ull) + ((offset) & 7) * 8)
+#define CVMX_DPI_DMAX_ERR_RSP_STATUS(offset) (CVMX_ADD_IO_SEG(0x0001DF0000000A80ull) + ((offset) & 7) * 8)
+#define CVMX_DPI_DMAX_IBUFF_SADDR(offset) (CVMX_ADD_IO_SEG(0x0001DF0000000280ull) + ((offset) & 7) * 8)
+#define CVMX_DPI_DMAX_IFLIGHT(offset) (CVMX_ADD_IO_SEG(0x0001DF0000000A00ull) + ((offset) & 7) * 8)
+#define CVMX_DPI_DMAX_NADDR(offset) (CVMX_ADD_IO_SEG(0x0001DF0000000380ull) + ((offset) & 7) * 8)
+#define CVMX_DPI_DMAX_REQBNK0(offset) (CVMX_ADD_IO_SEG(0x0001DF0000000400ull) + ((offset) & 7) * 8)
+#define CVMX_DPI_DMAX_REQBNK1(offset) (CVMX_ADD_IO_SEG(0x0001DF0000000480ull) + ((offset) & 7) * 8)
+#define CVMX_DPI_DMA_CONTROL (CVMX_ADD_IO_SEG(0x0001DF0000000048ull))
+#define CVMX_DPI_DMA_ENGX_EN(offset) (CVMX_ADD_IO_SEG(0x0001DF0000000080ull) + ((offset) & 7) * 8)
+#define CVMX_DPI_DMA_PPX_CNT(offset) (CVMX_ADD_IO_SEG(0x0001DF0000000B00ull) + ((offset) & 31) * 8)
+#define CVMX_DPI_ENGX_BUF(offset) (CVMX_ADD_IO_SEG(0x0001DF0000000880ull) + ((offset) & 7) * 8)
+#define CVMX_DPI_INFO_REG (CVMX_ADD_IO_SEG(0x0001DF0000000980ull))
+#define CVMX_DPI_INT_EN (CVMX_ADD_IO_SEG(0x0001DF0000000010ull))
+#define CVMX_DPI_INT_REG (CVMX_ADD_IO_SEG(0x0001DF0000000008ull))
+#define CVMX_DPI_NCBX_CFG(block_id) (CVMX_ADD_IO_SEG(0x0001DF0000000800ull))
+#define CVMX_DPI_PINT_INFO (CVMX_ADD_IO_SEG(0x0001DF0000000830ull))
+#define CVMX_DPI_PKT_ERR_RSP (CVMX_ADD_IO_SEG(0x0001DF0000000078ull))
+#define CVMX_DPI_REQ_ERR_RSP (CVMX_ADD_IO_SEG(0x0001DF0000000058ull))
+#define CVMX_DPI_REQ_ERR_RSP_EN (CVMX_ADD_IO_SEG(0x0001DF0000000068ull))
+#define CVMX_DPI_REQ_ERR_RST (CVMX_ADD_IO_SEG(0x0001DF0000000060ull))
+#define CVMX_DPI_REQ_ERR_RST_EN (CVMX_ADD_IO_SEG(0x0001DF0000000070ull))
+#define CVMX_DPI_REQ_ERR_SKIP_COMP (CVMX_ADD_IO_SEG(0x0001DF0000000838ull))
+#define CVMX_DPI_REQ_GBL_EN (CVMX_ADD_IO_SEG(0x0001DF0000000050ull))
+#define CVMX_DPI_SLI_PRTX_CFG(offset) (CVMX_ADD_IO_SEG(0x0001DF0000000900ull) + ((offset) & 3) * 8)
+static inline uint64_t CVMX_DPI_SLI_PRTX_ERR(unsigned long offset)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001DF0000000920ull) + (offset) * 8;
+	case OCTEON_CNF71XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+
+		if (OCTEON_IS_MODEL(OCTEON_CN68XX_PASS1))
+			return CVMX_ADD_IO_SEG(0x0001DF0000000928ull) + (offset) * 8;
+
+		if (OCTEON_IS_MODEL(OCTEON_CN68XX_PASS2))
+			return CVMX_ADD_IO_SEG(0x0001DF0000000920ull) + (offset) * 8;
+		return CVMX_ADD_IO_SEG(0x0001DF0000000920ull) + (offset) * 8;
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001DF0000000928ull) + (offset) * 8;
+	}
+	return CVMX_ADD_IO_SEG(0x0001DF0000000920ull) + (offset) * 8;
+}
+
+#define CVMX_DPI_SLI_PRTX_ERR_INFO(offset) (CVMX_ADD_IO_SEG(0x0001DF0000000940ull) + ((offset) & 3) * 8)
+
+union cvmx_dpi_bist_status {
+	uint64_t u64;
+	struct cvmx_dpi_bist_status_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_47_63:17;
+		uint64_t bist:47;
+#else
+		uint64_t bist:47;
+		uint64_t reserved_47_63:17;
+#endif
+	} s;
+	struct cvmx_dpi_bist_status_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_45_63:19;
+		uint64_t bist:45;
+#else
+		uint64_t bist:45;
+		uint64_t reserved_45_63:19;
+#endif
+	} cn63xx;
+	struct cvmx_dpi_bist_status_cn63xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_37_63:27;
+		uint64_t bist:37;
+#else
+		uint64_t bist:37;
+		uint64_t reserved_37_63:27;
+#endif
+	} cn63xxp1;
+};
+
+union cvmx_dpi_ctl {
+	uint64_t u64;
+	struct cvmx_dpi_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t clk:1;
+		uint64_t en:1;
+#else
+		uint64_t en:1;
+		uint64_t clk:1;
+		uint64_t reserved_2_63:62;
+#endif
+	} s;
+	struct cvmx_dpi_ctl_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t en:1;
+#else
+		uint64_t en:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} cn61xx;
+};
+
+union cvmx_dpi_dmax_counts {
+	uint64_t u64;
+	struct cvmx_dpi_dmax_counts_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_39_63:25;
+		uint64_t fcnt:7;
+		uint64_t dbell:32;
+#else
+		uint64_t dbell:32;
+		uint64_t fcnt:7;
+		uint64_t reserved_39_63:25;
+#endif
+	} s;
+};
+
+union cvmx_dpi_dmax_dbell {
+	uint64_t u64;
+	struct cvmx_dpi_dmax_dbell_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t dbell:16;
+#else
+		uint64_t dbell:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_dpi_dmax_err_rsp_status {
+	uint64_t u64;
+	struct cvmx_dpi_dmax_err_rsp_status_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t status:6;
+#else
+		uint64_t status:6;
+		uint64_t reserved_6_63:58;
+#endif
+	} s;
+};
+
+union cvmx_dpi_dmax_ibuff_saddr {
+	uint64_t u64;
+	struct cvmx_dpi_dmax_ibuff_saddr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_62_63:2;
+		uint64_t csize:14;
+		uint64_t reserved_41_47:7;
+		uint64_t idle:1;
+		uint64_t saddr:33;
+		uint64_t reserved_0_6:7;
+#else
+		uint64_t reserved_0_6:7;
+		uint64_t saddr:33;
+		uint64_t idle:1;
+		uint64_t reserved_41_47:7;
+		uint64_t csize:14;
+		uint64_t reserved_62_63:2;
+#endif
+	} s;
+	struct cvmx_dpi_dmax_ibuff_saddr_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_62_63:2;
+		uint64_t csize:14;
+		uint64_t reserved_41_47:7;
+		uint64_t idle:1;
+		uint64_t reserved_36_39:4;
+		uint64_t saddr:29;
+		uint64_t reserved_0_6:7;
+#else
+		uint64_t reserved_0_6:7;
+		uint64_t saddr:29;
+		uint64_t reserved_36_39:4;
+		uint64_t idle:1;
+		uint64_t reserved_41_47:7;
+		uint64_t csize:14;
+		uint64_t reserved_62_63:2;
+#endif
+	} cn61xx;
+};
+
+union cvmx_dpi_dmax_iflight {
+	uint64_t u64;
+	struct cvmx_dpi_dmax_iflight_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_3_63:61;
+		uint64_t cnt:3;
+#else
+		uint64_t cnt:3;
+		uint64_t reserved_3_63:61;
+#endif
+	} s;
+};
+
+union cvmx_dpi_dmax_naddr {
+	uint64_t u64;
+	struct cvmx_dpi_dmax_naddr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_40_63:24;
+		uint64_t addr:40;
+#else
+		uint64_t addr:40;
+		uint64_t reserved_40_63:24;
+#endif
+	} s;
+	struct cvmx_dpi_dmax_naddr_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_36_63:28;
+		uint64_t addr:36;
+#else
+		uint64_t addr:36;
+		uint64_t reserved_36_63:28;
+#endif
+	} cn61xx;
+};
+
+union cvmx_dpi_dmax_reqbnk0 {
+	uint64_t u64;
+	struct cvmx_dpi_dmax_reqbnk0_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t state:64;
+#else
+		uint64_t state:64;
+#endif
+	} s;
+};
+
+union cvmx_dpi_dmax_reqbnk1 {
+	uint64_t u64;
+	struct cvmx_dpi_dmax_reqbnk1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t state:64;
+#else
+		uint64_t state:64;
+#endif
+	} s;
+};
+
+union cvmx_dpi_dma_control {
+	uint64_t u64;
+	struct cvmx_dpi_dma_control_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_62_63:2;
+		uint64_t dici_mode:1;
+		uint64_t pkt_en1:1;
+		uint64_t ffp_dis:1;
+		uint64_t commit_mode:1;
+		uint64_t pkt_hp:1;
+		uint64_t pkt_en:1;
+		uint64_t reserved_54_55:2;
+		uint64_t dma_enb:6;
+		uint64_t reserved_34_47:14;
+		uint64_t b0_lend:1;
+		uint64_t dwb_denb:1;
+		uint64_t dwb_ichk:9;
+		uint64_t fpa_que:3;
+		uint64_t o_add1:1;
+		uint64_t o_ro:1;
+		uint64_t o_ns:1;
+		uint64_t o_es:2;
+		uint64_t o_mode:1;
+		uint64_t reserved_0_13:14;
+#else
+		uint64_t reserved_0_13:14;
+		uint64_t o_mode:1;
+		uint64_t o_es:2;
+		uint64_t o_ns:1;
+		uint64_t o_ro:1;
+		uint64_t o_add1:1;
+		uint64_t fpa_que:3;
+		uint64_t dwb_ichk:9;
+		uint64_t dwb_denb:1;
+		uint64_t b0_lend:1;
+		uint64_t reserved_34_47:14;
+		uint64_t dma_enb:6;
+		uint64_t reserved_54_55:2;
+		uint64_t pkt_en:1;
+		uint64_t pkt_hp:1;
+		uint64_t commit_mode:1;
+		uint64_t ffp_dis:1;
+		uint64_t pkt_en1:1;
+		uint64_t dici_mode:1;
+		uint64_t reserved_62_63:2;
+#endif
+	} s;
+	struct cvmx_dpi_dma_control_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_61_63:3;
+		uint64_t pkt_en1:1;
+		uint64_t ffp_dis:1;
+		uint64_t commit_mode:1;
+		uint64_t pkt_hp:1;
+		uint64_t pkt_en:1;
+		uint64_t reserved_54_55:2;
+		uint64_t dma_enb:6;
+		uint64_t reserved_34_47:14;
+		uint64_t b0_lend:1;
+		uint64_t dwb_denb:1;
+		uint64_t dwb_ichk:9;
+		uint64_t fpa_que:3;
+		uint64_t o_add1:1;
+		uint64_t o_ro:1;
+		uint64_t o_ns:1;
+		uint64_t o_es:2;
+		uint64_t o_mode:1;
+		uint64_t reserved_0_13:14;
+#else
+		uint64_t reserved_0_13:14;
+		uint64_t o_mode:1;
+		uint64_t o_es:2;
+		uint64_t o_ns:1;
+		uint64_t o_ro:1;
+		uint64_t o_add1:1;
+		uint64_t fpa_que:3;
+		uint64_t dwb_ichk:9;
+		uint64_t dwb_denb:1;
+		uint64_t b0_lend:1;
+		uint64_t reserved_34_47:14;
+		uint64_t dma_enb:6;
+		uint64_t reserved_54_55:2;
+		uint64_t pkt_en:1;
+		uint64_t pkt_hp:1;
+		uint64_t commit_mode:1;
+		uint64_t ffp_dis:1;
+		uint64_t pkt_en1:1;
+		uint64_t reserved_61_63:3;
+#endif
+	} cn63xx;
+	struct cvmx_dpi_dma_control_cn63xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_59_63:5;
+		uint64_t commit_mode:1;
+		uint64_t pkt_hp:1;
+		uint64_t pkt_en:1;
+		uint64_t reserved_54_55:2;
+		uint64_t dma_enb:6;
+		uint64_t reserved_34_47:14;
+		uint64_t b0_lend:1;
+		uint64_t dwb_denb:1;
+		uint64_t dwb_ichk:9;
+		uint64_t fpa_que:3;
+		uint64_t o_add1:1;
+		uint64_t o_ro:1;
+		uint64_t o_ns:1;
+		uint64_t o_es:2;
+		uint64_t o_mode:1;
+		uint64_t reserved_0_13:14;
+#else
+		uint64_t reserved_0_13:14;
+		uint64_t o_mode:1;
+		uint64_t o_es:2;
+		uint64_t o_ns:1;
+		uint64_t o_ro:1;
+		uint64_t o_add1:1;
+		uint64_t fpa_que:3;
+		uint64_t dwb_ichk:9;
+		uint64_t dwb_denb:1;
+		uint64_t b0_lend:1;
+		uint64_t reserved_34_47:14;
+		uint64_t dma_enb:6;
+		uint64_t reserved_54_55:2;
+		uint64_t pkt_en:1;
+		uint64_t pkt_hp:1;
+		uint64_t commit_mode:1;
+		uint64_t reserved_59_63:5;
+#endif
+	} cn63xxp1;
+};
+
+union cvmx_dpi_dma_engx_en {
+	uint64_t u64;
+	struct cvmx_dpi_dma_engx_en_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t qen:8;
+#else
+		uint64_t qen:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_dpi_dma_ppx_cnt {
+	uint64_t u64;
+	struct cvmx_dpi_dma_ppx_cnt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t cnt:16;
+#else
+		uint64_t cnt:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_dpi_engx_buf {
+	uint64_t u64;
+	struct cvmx_dpi_engx_buf_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_37_63:27;
+		uint64_t compblks:5;
+		uint64_t reserved_9_31:23;
+		uint64_t base:5;
+		uint64_t blks:4;
+#else
+		uint64_t blks:4;
+		uint64_t base:5;
+		uint64_t reserved_9_31:23;
+		uint64_t compblks:5;
+		uint64_t reserved_37_63:27;
+#endif
+	} s;
+	struct cvmx_dpi_engx_buf_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t base:4;
+		uint64_t blks:4;
+#else
+		uint64_t blks:4;
+		uint64_t base:4;
+		uint64_t reserved_8_63:56;
+#endif
+	} cn63xx;
+};
+
+union cvmx_dpi_info_reg {
+	uint64_t u64;
+	struct cvmx_dpi_info_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t ffp:4;
+		uint64_t reserved_2_3:2;
+		uint64_t ncb:1;
+		uint64_t rsl:1;
+#else
+		uint64_t rsl:1;
+		uint64_t ncb:1;
+		uint64_t reserved_2_3:2;
+		uint64_t ffp:4;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+	struct cvmx_dpi_info_reg_cn63xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t ncb:1;
+		uint64_t rsl:1;
+#else
+		uint64_t rsl:1;
+		uint64_t ncb:1;
+		uint64_t reserved_2_63:62;
+#endif
+	} cn63xxp1;
+};
+
+union cvmx_dpi_int_en {
+	uint64_t u64;
+	struct cvmx_dpi_int_en_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_28_63:36;
+		uint64_t sprt3_rst:1;
+		uint64_t sprt2_rst:1;
+		uint64_t sprt1_rst:1;
+		uint64_t sprt0_rst:1;
+		uint64_t reserved_23_23:1;
+		uint64_t req_badfil:1;
+		uint64_t req_inull:1;
+		uint64_t req_anull:1;
+		uint64_t req_undflw:1;
+		uint64_t req_ovrflw:1;
+		uint64_t req_badlen:1;
+		uint64_t req_badadr:1;
+		uint64_t dmadbo:8;
+		uint64_t reserved_2_7:6;
+		uint64_t nfovr:1;
+		uint64_t nderr:1;
+#else
+		uint64_t nderr:1;
+		uint64_t nfovr:1;
+		uint64_t reserved_2_7:6;
+		uint64_t dmadbo:8;
+		uint64_t req_badadr:1;
+		uint64_t req_badlen:1;
+		uint64_t req_ovrflw:1;
+		uint64_t req_undflw:1;
+		uint64_t req_anull:1;
+		uint64_t req_inull:1;
+		uint64_t req_badfil:1;
+		uint64_t reserved_23_23:1;
+		uint64_t sprt0_rst:1;
+		uint64_t sprt1_rst:1;
+		uint64_t sprt2_rst:1;
+		uint64_t sprt3_rst:1;
+		uint64_t reserved_28_63:36;
+#endif
+	} s;
+	struct cvmx_dpi_int_en_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_26_63:38;
+		uint64_t sprt1_rst:1;
+		uint64_t sprt0_rst:1;
+		uint64_t reserved_23_23:1;
+		uint64_t req_badfil:1;
+		uint64_t req_inull:1;
+		uint64_t req_anull:1;
+		uint64_t req_undflw:1;
+		uint64_t req_ovrflw:1;
+		uint64_t req_badlen:1;
+		uint64_t req_badadr:1;
+		uint64_t dmadbo:8;
+		uint64_t reserved_2_7:6;
+		uint64_t nfovr:1;
+		uint64_t nderr:1;
+#else
+		uint64_t nderr:1;
+		uint64_t nfovr:1;
+		uint64_t reserved_2_7:6;
+		uint64_t dmadbo:8;
+		uint64_t req_badadr:1;
+		uint64_t req_badlen:1;
+		uint64_t req_ovrflw:1;
+		uint64_t req_undflw:1;
+		uint64_t req_anull:1;
+		uint64_t req_inull:1;
+		uint64_t req_badfil:1;
+		uint64_t reserved_23_23:1;
+		uint64_t sprt0_rst:1;
+		uint64_t sprt1_rst:1;
+		uint64_t reserved_26_63:38;
+#endif
+	} cn63xx;
+};
+
+union cvmx_dpi_int_reg {
+	uint64_t u64;
+	struct cvmx_dpi_int_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_28_63:36;
+		uint64_t sprt3_rst:1;
+		uint64_t sprt2_rst:1;
+		uint64_t sprt1_rst:1;
+		uint64_t sprt0_rst:1;
+		uint64_t reserved_23_23:1;
+		uint64_t req_badfil:1;
+		uint64_t req_inull:1;
+		uint64_t req_anull:1;
+		uint64_t req_undflw:1;
+		uint64_t req_ovrflw:1;
+		uint64_t req_badlen:1;
+		uint64_t req_badadr:1;
+		uint64_t dmadbo:8;
+		uint64_t reserved_2_7:6;
+		uint64_t nfovr:1;
+		uint64_t nderr:1;
+#else
+		uint64_t nderr:1;
+		uint64_t nfovr:1;
+		uint64_t reserved_2_7:6;
+		uint64_t dmadbo:8;
+		uint64_t req_badadr:1;
+		uint64_t req_badlen:1;
+		uint64_t req_ovrflw:1;
+		uint64_t req_undflw:1;
+		uint64_t req_anull:1;
+		uint64_t req_inull:1;
+		uint64_t req_badfil:1;
+		uint64_t reserved_23_23:1;
+		uint64_t sprt0_rst:1;
+		uint64_t sprt1_rst:1;
+		uint64_t sprt2_rst:1;
+		uint64_t sprt3_rst:1;
+		uint64_t reserved_28_63:36;
+#endif
+	} s;
+	struct cvmx_dpi_int_reg_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_26_63:38;
+		uint64_t sprt1_rst:1;
+		uint64_t sprt0_rst:1;
+		uint64_t reserved_23_23:1;
+		uint64_t req_badfil:1;
+		uint64_t req_inull:1;
+		uint64_t req_anull:1;
+		uint64_t req_undflw:1;
+		uint64_t req_ovrflw:1;
+		uint64_t req_badlen:1;
+		uint64_t req_badadr:1;
+		uint64_t dmadbo:8;
+		uint64_t reserved_2_7:6;
+		uint64_t nfovr:1;
+		uint64_t nderr:1;
+#else
+		uint64_t nderr:1;
+		uint64_t nfovr:1;
+		uint64_t reserved_2_7:6;
+		uint64_t dmadbo:8;
+		uint64_t req_badadr:1;
+		uint64_t req_badlen:1;
+		uint64_t req_ovrflw:1;
+		uint64_t req_undflw:1;
+		uint64_t req_anull:1;
+		uint64_t req_inull:1;
+		uint64_t req_badfil:1;
+		uint64_t reserved_23_23:1;
+		uint64_t sprt0_rst:1;
+		uint64_t sprt1_rst:1;
+		uint64_t reserved_26_63:38;
+#endif
+	} cn63xx;
+};
+
+union cvmx_dpi_ncbx_cfg {
+	uint64_t u64;
+	struct cvmx_dpi_ncbx_cfg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t molr:6;
+#else
+		uint64_t molr:6;
+		uint64_t reserved_6_63:58;
+#endif
+	} s;
+};
+
+union cvmx_dpi_pint_info {
+	uint64_t u64;
+	struct cvmx_dpi_pint_info_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_14_63:50;
+		uint64_t iinfo:6;
+		uint64_t reserved_6_7:2;
+		uint64_t sinfo:6;
+#else
+		uint64_t sinfo:6;
+		uint64_t reserved_6_7:2;
+		uint64_t iinfo:6;
+		uint64_t reserved_14_63:50;
+#endif
+	} s;
+};
+
+union cvmx_dpi_pkt_err_rsp {
+	uint64_t u64;
+	struct cvmx_dpi_pkt_err_rsp_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t pkterr:1;
+#else
+		uint64_t pkterr:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_dpi_req_err_rsp {
+	uint64_t u64;
+	struct cvmx_dpi_req_err_rsp_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t qerr:8;
+#else
+		uint64_t qerr:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_dpi_req_err_rsp_en {
+	uint64_t u64;
+	struct cvmx_dpi_req_err_rsp_en_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t en:8;
+#else
+		uint64_t en:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_dpi_req_err_rst {
+	uint64_t u64;
+	struct cvmx_dpi_req_err_rst_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t qerr:8;
+#else
+		uint64_t qerr:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_dpi_req_err_rst_en {
+	uint64_t u64;
+	struct cvmx_dpi_req_err_rst_en_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t en:8;
+#else
+		uint64_t en:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_dpi_req_err_skip_comp {
+	uint64_t u64;
+	struct cvmx_dpi_req_err_skip_comp_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_24_63:40;
+		uint64_t en_rst:8;
+		uint64_t reserved_8_15:8;
+		uint64_t en_rsp:8;
+#else
+		uint64_t en_rsp:8;
+		uint64_t reserved_8_15:8;
+		uint64_t en_rst:8;
+		uint64_t reserved_24_63:40;
+#endif
+	} s;
+};
+
+union cvmx_dpi_req_gbl_en {
+	uint64_t u64;
+	struct cvmx_dpi_req_gbl_en_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t qen:8;
+#else
+		uint64_t qen:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_dpi_sli_prtx_cfg {
+	uint64_t u64;
+	struct cvmx_dpi_sli_prtx_cfg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_25_63:39;
+		uint64_t halt:1;
+		uint64_t qlm_cfg:4;
+		uint64_t reserved_17_19:3;
+		uint64_t rd_mode:1;
+		uint64_t reserved_14_15:2;
+		uint64_t molr:6;
+		uint64_t mps_lim:1;
+		uint64_t reserved_5_6:2;
+		uint64_t mps:1;
+		uint64_t mrrs_lim:1;
+		uint64_t reserved_2_2:1;
+		uint64_t mrrs:2;
+#else
+		uint64_t mrrs:2;
+		uint64_t reserved_2_2:1;
+		uint64_t mrrs_lim:1;
+		uint64_t mps:1;
+		uint64_t reserved_5_6:2;
+		uint64_t mps_lim:1;
+		uint64_t molr:6;
+		uint64_t reserved_14_15:2;
+		uint64_t rd_mode:1;
+		uint64_t reserved_17_19:3;
+		uint64_t qlm_cfg:4;
+		uint64_t halt:1;
+		uint64_t reserved_25_63:39;
+#endif
+	} s;
+	struct cvmx_dpi_sli_prtx_cfg_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_25_63:39;
+		uint64_t halt:1;
+		uint64_t reserved_21_23:3;
+		uint64_t qlm_cfg:1;
+		uint64_t reserved_17_19:3;
+		uint64_t rd_mode:1;
+		uint64_t reserved_14_15:2;
+		uint64_t molr:6;
+		uint64_t mps_lim:1;
+		uint64_t reserved_5_6:2;
+		uint64_t mps:1;
+		uint64_t mrrs_lim:1;
+		uint64_t reserved_2_2:1;
+		uint64_t mrrs:2;
+#else
+		uint64_t mrrs:2;
+		uint64_t reserved_2_2:1;
+		uint64_t mrrs_lim:1;
+		uint64_t mps:1;
+		uint64_t reserved_5_6:2;
+		uint64_t mps_lim:1;
+		uint64_t molr:6;
+		uint64_t reserved_14_15:2;
+		uint64_t rd_mode:1;
+		uint64_t reserved_17_19:3;
+		uint64_t qlm_cfg:1;
+		uint64_t reserved_21_23:3;
+		uint64_t halt:1;
+		uint64_t reserved_25_63:39;
+#endif
+	} cn63xx;
+};
+
+union cvmx_dpi_sli_prtx_err {
+	uint64_t u64;
+	struct cvmx_dpi_sli_prtx_err_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t addr:61;
+		uint64_t reserved_0_2:3;
+#else
+		uint64_t reserved_0_2:3;
+		uint64_t addr:61;
+#endif
+	} s;
+};
+
+union cvmx_dpi_sli_prtx_err_info {
+	uint64_t u64;
+	struct cvmx_dpi_sli_prtx_err_info_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_9_63:55;
+		uint64_t lock:1;
+		uint64_t reserved_5_7:3;
+		uint64_t type:1;
+		uint64_t reserved_3_3:1;
+		uint64_t reqq:3;
+#else
+		uint64_t reqq:3;
+		uint64_t reserved_3_3:1;
+		uint64_t type:1;
+		uint64_t reserved_5_7:3;
+		uint64_t lock:1;
+		uint64_t reserved_9_63:55;
+#endif
+	} s;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-fau.h b/arch/mips/include/asm/octeon/cvmx-fau.h
new file mode 100644
index 000000000..dafeae300
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-fau.h
@@ -0,0 +1,619 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ * Interface to the hardware Fetch and Add Unit.
+ */
+
+#ifndef __CVMX_FAU_H__
+#define __CVMX_FAU_H__
+
+/*
+ * Octeon Fetch and Add Unit (FAU)
+ */
+
+#define CVMX_FAU_LOAD_IO_ADDRESS    cvmx_build_io_address(0x1e, 0)
+#define CVMX_FAU_BITS_SCRADDR	    63, 56
+#define CVMX_FAU_BITS_LEN	    55, 48
+#define CVMX_FAU_BITS_INEVAL	    35, 14
+#define CVMX_FAU_BITS_TAGWAIT	    13, 13
+#define CVMX_FAU_BITS_NOADD	    13, 13
+#define CVMX_FAU_BITS_SIZE	    12, 11
+#define CVMX_FAU_BITS_REGISTER	    10, 0
+
+typedef enum {
+	CVMX_FAU_OP_SIZE_8 = 0,
+	CVMX_FAU_OP_SIZE_16 = 1,
+	CVMX_FAU_OP_SIZE_32 = 2,
+	CVMX_FAU_OP_SIZE_64 = 3
+} cvmx_fau_op_size_t;
+
+/**
+ * Tagwait return definition. If a timeout occurs, the error
+ * bit will be set. Otherwise the value of the register before
+ * the update will be returned.
+ */
+typedef struct {
+	uint64_t error:1;
+	int64_t value:63;
+} cvmx_fau_tagwait64_t;
+
+/**
+ * Tagwait return definition. If a timeout occurs, the error
+ * bit will be set. Otherwise the value of the register before
+ * the update will be returned.
+ */
+typedef struct {
+	uint64_t error:1;
+	int32_t value:31;
+} cvmx_fau_tagwait32_t;
+
+/**
+ * Tagwait return definition. If a timeout occurs, the error
+ * bit will be set. Otherwise the value of the register before
+ * the update will be returned.
+ */
+typedef struct {
+	uint64_t error:1;
+	int16_t value:15;
+} cvmx_fau_tagwait16_t;
+
+/**
+ * Tagwait return definition. If a timeout occurs, the error
+ * bit will be set. Otherwise the value of the register before
+ * the update will be returned.
+ */
+typedef struct {
+	uint64_t error:1;
+	int8_t value:7;
+} cvmx_fau_tagwait8_t;
+
+/**
+ * Asynchronous tagwait return definition. If a timeout occurs,
+ * the error bit will be set. Otherwise the value of the
+ * register before the update will be returned.
+ */
+typedef union {
+	uint64_t u64;
+	struct {
+		uint64_t invalid:1;
+		uint64_t data:63;	/* unpredictable if invalid is set */
+	} s;
+} cvmx_fau_async_tagwait_result_t;
+
+#ifdef __BIG_ENDIAN_BITFIELD
+#define SWIZZLE_8  0
+#define SWIZZLE_16 0
+#define SWIZZLE_32 0
+#else
+#define SWIZZLE_8  0x7
+#define SWIZZLE_16 0x6
+#define SWIZZLE_32 0x4
+#endif
+
+/**
+ * Builds a store I/O address for writing to the FAU
+ *
+ * @noadd:  0 = Store value is atomically added to the current value
+ *		 1 = Store value is atomically written over the current value
+ * @reg:    FAU atomic register to access. 0 <= reg < 2048.
+ *		 - Step by 2 for 16 bit access.
+ *		 - Step by 4 for 32 bit access.
+ *		 - Step by 8 for 64 bit access.
+ * Returns Address to store for atomic update
+ */
+static inline uint64_t __cvmx_fau_store_address(uint64_t noadd, uint64_t reg)
+{
+	return CVMX_ADD_IO_SEG(CVMX_FAU_LOAD_IO_ADDRESS) |
+	       cvmx_build_bits(CVMX_FAU_BITS_NOADD, noadd) |
+	       cvmx_build_bits(CVMX_FAU_BITS_REGISTER, reg);
+}
+
+/**
+ * Builds a I/O address for accessing the FAU
+ *
+ * @tagwait: Should the atomic add wait for the current tag switch
+ *		  operation to complete.
+ *		  - 0 = Don't wait
+ *		  - 1 = Wait for tag switch to complete
+ * @reg:     FAU atomic register to access. 0 <= reg < 2048.
+ *		  - Step by 2 for 16 bit access.
+ *		  - Step by 4 for 32 bit access.
+ *		  - Step by 8 for 64 bit access.
+ * @value:   Signed value to add.
+ *		  Note: When performing 32 and 64 bit access, only the low
+ *		  22 bits are available.
+ * Returns Address to read from for atomic update
+ */
+static inline uint64_t __cvmx_fau_atomic_address(uint64_t tagwait, uint64_t reg,
+						 int64_t value)
+{
+	return CVMX_ADD_IO_SEG(CVMX_FAU_LOAD_IO_ADDRESS) |
+	       cvmx_build_bits(CVMX_FAU_BITS_INEVAL, value) |
+	       cvmx_build_bits(CVMX_FAU_BITS_TAGWAIT, tagwait) |
+	       cvmx_build_bits(CVMX_FAU_BITS_REGISTER, reg);
+}
+
+/**
+ * Perform an atomic 64 bit add
+ *
+ * @reg:     FAU atomic register to access. 0 <= reg < 2048.
+ *		  - Step by 8 for 64 bit access.
+ * @value:   Signed value to add.
+ *		  Note: Only the low 22 bits are available.
+ * Returns Value of the register before the update
+ */
+static inline int64_t cvmx_fau_fetch_and_add64(cvmx_fau_reg_64_t reg,
+					       int64_t value)
+{
+	return cvmx_read64_int64(__cvmx_fau_atomic_address(0, reg, value));
+}
+
+/**
+ * Perform an atomic 32 bit add
+ *
+ * @reg:     FAU atomic register to access. 0 <= reg < 2048.
+ *		  - Step by 4 for 32 bit access.
+ * @value:   Signed value to add.
+ *		  Note: Only the low 22 bits are available.
+ * Returns Value of the register before the update
+ */
+static inline int32_t cvmx_fau_fetch_and_add32(cvmx_fau_reg_32_t reg,
+					       int32_t value)
+{
+	reg ^= SWIZZLE_32;
+	return cvmx_read64_int32(__cvmx_fau_atomic_address(0, reg, value));
+}
+
+/**
+ * Perform an atomic 16 bit add
+ *
+ * @reg:     FAU atomic register to access. 0 <= reg < 2048.
+ *		  - Step by 2 for 16 bit access.
+ * @value:   Signed value to add.
+ * Returns Value of the register before the update
+ */
+static inline int16_t cvmx_fau_fetch_and_add16(cvmx_fau_reg_16_t reg,
+					       int16_t value)
+{
+	reg ^= SWIZZLE_16;
+	return cvmx_read64_int16(__cvmx_fau_atomic_address(0, reg, value));
+}
+
+/**
+ * Perform an atomic 8 bit add
+ *
+ * @reg:     FAU atomic register to access. 0 <= reg < 2048.
+ * @value:   Signed value to add.
+ * Returns Value of the register before the update
+ */
+static inline int8_t cvmx_fau_fetch_and_add8(cvmx_fau_reg_8_t reg, int8_t value)
+{
+	reg ^= SWIZZLE_8;
+	return cvmx_read64_int8(__cvmx_fau_atomic_address(0, reg, value));
+}
+
+/**
+ * Perform an atomic 64 bit add after the current tag switch
+ * completes
+ *
+ * @reg:    FAU atomic register to access. 0 <= reg < 2048.
+ *		 - Step by 8 for 64 bit access.
+ * @value:  Signed value to add.
+ *		 Note: Only the low 22 bits are available.
+ * Returns If a timeout occurs, the error bit will be set. Otherwise
+ *	   the value of the register before the update will be
+ *	   returned
+ */
+static inline cvmx_fau_tagwait64_t
+cvmx_fau_tagwait_fetch_and_add64(cvmx_fau_reg_64_t reg, int64_t value)
+{
+	union {
+		uint64_t i64;
+		cvmx_fau_tagwait64_t t;
+	} result;
+	result.i64 =
+	    cvmx_read64_int64(__cvmx_fau_atomic_address(1, reg, value));
+	return result.t;
+}
+
+/**
+ * Perform an atomic 32 bit add after the current tag switch
+ * completes
+ *
+ * @reg:    FAU atomic register to access. 0 <= reg < 2048.
+ *		 - Step by 4 for 32 bit access.
+ * @value:  Signed value to add.
+ *		 Note: Only the low 22 bits are available.
+ * Returns If a timeout occurs, the error bit will be set. Otherwise
+ *	   the value of the register before the update will be
+ *	   returned
+ */
+static inline cvmx_fau_tagwait32_t
+cvmx_fau_tagwait_fetch_and_add32(cvmx_fau_reg_32_t reg, int32_t value)
+{
+	union {
+		uint64_t i32;
+		cvmx_fau_tagwait32_t t;
+	} result;
+	reg ^= SWIZZLE_32;
+	result.i32 =
+	    cvmx_read64_int32(__cvmx_fau_atomic_address(1, reg, value));
+	return result.t;
+}
+
+/**
+ * Perform an atomic 16 bit add after the current tag switch
+ * completes
+ *
+ * @reg:    FAU atomic register to access. 0 <= reg < 2048.
+ *		 - Step by 2 for 16 bit access.
+ * @value:  Signed value to add.
+ * Returns If a timeout occurs, the error bit will be set. Otherwise
+ *	   the value of the register before the update will be
+ *	   returned
+ */
+static inline cvmx_fau_tagwait16_t
+cvmx_fau_tagwait_fetch_and_add16(cvmx_fau_reg_16_t reg, int16_t value)
+{
+	union {
+		uint64_t i16;
+		cvmx_fau_tagwait16_t t;
+	} result;
+	reg ^= SWIZZLE_16;
+	result.i16 =
+	    cvmx_read64_int16(__cvmx_fau_atomic_address(1, reg, value));
+	return result.t;
+}
+
+/**
+ * Perform an atomic 8 bit add after the current tag switch
+ * completes
+ *
+ * @reg:    FAU atomic register to access. 0 <= reg < 2048.
+ * @value:  Signed value to add.
+ * Returns If a timeout occurs, the error bit will be set. Otherwise
+ *	   the value of the register before the update will be
+ *	   returned
+ */
+static inline cvmx_fau_tagwait8_t
+cvmx_fau_tagwait_fetch_and_add8(cvmx_fau_reg_8_t reg, int8_t value)
+{
+	union {
+		uint64_t i8;
+		cvmx_fau_tagwait8_t t;
+	} result;
+	reg ^= SWIZZLE_8;
+	result.i8 = cvmx_read64_int8(__cvmx_fau_atomic_address(1, reg, value));
+	return result.t;
+}
+
+/**
+ * Builds I/O data for async operations
+ *
+ * @scraddr: Scratch pad byte address to write to.  Must be 8 byte aligned
+ * @value:   Signed value to add.
+ *		  Note: When performing 32 and 64 bit access, only the low
+ *		  22 bits are available.
+ * @tagwait: Should the atomic add wait for the current tag switch
+ *		  operation to complete.
+ *		  - 0 = Don't wait
+ *		  - 1 = Wait for tag switch to complete
+ * @size:    The size of the operation:
+ *		  - CVMX_FAU_OP_SIZE_8	(0) = 8 bits
+ *		  - CVMX_FAU_OP_SIZE_16 (1) = 16 bits
+ *		  - CVMX_FAU_OP_SIZE_32 (2) = 32 bits
+ *		  - CVMX_FAU_OP_SIZE_64 (3) = 64 bits
+ * @reg:     FAU atomic register to access. 0 <= reg < 2048.
+ *		  - Step by 2 for 16 bit access.
+ *		  - Step by 4 for 32 bit access.
+ *		  - Step by 8 for 64 bit access.
+ * Returns Data to write using cvmx_send_single
+ */
+static inline uint64_t __cvmx_fau_iobdma_data(uint64_t scraddr, int64_t value,
+					      uint64_t tagwait,
+					      cvmx_fau_op_size_t size,
+					      uint64_t reg)
+{
+	return CVMX_FAU_LOAD_IO_ADDRESS |
+	       cvmx_build_bits(CVMX_FAU_BITS_SCRADDR, scraddr >> 3) |
+	       cvmx_build_bits(CVMX_FAU_BITS_LEN, 1) |
+	       cvmx_build_bits(CVMX_FAU_BITS_INEVAL, value) |
+	       cvmx_build_bits(CVMX_FAU_BITS_TAGWAIT, tagwait) |
+	       cvmx_build_bits(CVMX_FAU_BITS_SIZE, size) |
+	       cvmx_build_bits(CVMX_FAU_BITS_REGISTER, reg);
+}
+
+/**
+ * Perform an async atomic 64 bit add. The old value is
+ * placed in the scratch memory at byte address scraddr.
+ *
+ * @scraddr: Scratch memory byte address to put response in.
+ *		  Must be 8 byte aligned.
+ * @reg:     FAU atomic register to access. 0 <= reg < 2048.
+ *		  - Step by 8 for 64 bit access.
+ * @value:   Signed value to add.
+ *		  Note: Only the low 22 bits are available.
+ * Returns Placed in the scratch pad register
+ */
+static inline void cvmx_fau_async_fetch_and_add64(uint64_t scraddr,
+						  cvmx_fau_reg_64_t reg,
+						  int64_t value)
+{
+	cvmx_send_single(__cvmx_fau_iobdma_data
+			 (scraddr, value, 0, CVMX_FAU_OP_SIZE_64, reg));
+}
+
+/**
+ * Perform an async atomic 32 bit add. The old value is
+ * placed in the scratch memory at byte address scraddr.
+ *
+ * @scraddr: Scratch memory byte address to put response in.
+ *		  Must be 8 byte aligned.
+ * @reg:     FAU atomic register to access. 0 <= reg < 2048.
+ *		  - Step by 4 for 32 bit access.
+ * @value:   Signed value to add.
+ *		  Note: Only the low 22 bits are available.
+ * Returns Placed in the scratch pad register
+ */
+static inline void cvmx_fau_async_fetch_and_add32(uint64_t scraddr,
+						  cvmx_fau_reg_32_t reg,
+						  int32_t value)
+{
+	cvmx_send_single(__cvmx_fau_iobdma_data
+			 (scraddr, value, 0, CVMX_FAU_OP_SIZE_32, reg));
+}
+
+/**
+ * Perform an async atomic 16 bit add. The old value is
+ * placed in the scratch memory at byte address scraddr.
+ *
+ * @scraddr: Scratch memory byte address to put response in.
+ *		  Must be 8 byte aligned.
+ * @reg:     FAU atomic register to access. 0 <= reg < 2048.
+ *		  - Step by 2 for 16 bit access.
+ * @value:   Signed value to add.
+ * Returns Placed in the scratch pad register
+ */
+static inline void cvmx_fau_async_fetch_and_add16(uint64_t scraddr,
+						  cvmx_fau_reg_16_t reg,
+						  int16_t value)
+{
+	cvmx_send_single(__cvmx_fau_iobdma_data
+			 (scraddr, value, 0, CVMX_FAU_OP_SIZE_16, reg));
+}
+
+/**
+ * Perform an async atomic 8 bit add. The old value is
+ * placed in the scratch memory at byte address scraddr.
+ *
+ * @scraddr: Scratch memory byte address to put response in.
+ *		  Must be 8 byte aligned.
+ * @reg:     FAU atomic register to access. 0 <= reg < 2048.
+ * @value:   Signed value to add.
+ * Returns Placed in the scratch pad register
+ */
+static inline void cvmx_fau_async_fetch_and_add8(uint64_t scraddr,
+						 cvmx_fau_reg_8_t reg,
+						 int8_t value)
+{
+	cvmx_send_single(__cvmx_fau_iobdma_data
+			 (scraddr, value, 0, CVMX_FAU_OP_SIZE_8, reg));
+}
+
+/**
+ * Perform an async atomic 64 bit add after the current tag
+ * switch completes.
+ *
+ * @scraddr: Scratch memory byte address to put response in.  Must be
+ *	     8 byte aligned.  If a timeout occurs, the error bit (63)
+ *	     will be set. Otherwise the value of the register before
+ *	     the update will be returned
+ *
+ * @reg:     FAU atomic register to access. 0 <= reg < 2048.
+ *		  - Step by 8 for 64 bit access.
+ * @value:   Signed value to add.
+ *		  Note: Only the low 22 bits are available.
+ * Returns Placed in the scratch pad register
+ */
+static inline void cvmx_fau_async_tagwait_fetch_and_add64(uint64_t scraddr,
+							  cvmx_fau_reg_64_t reg,
+							  int64_t value)
+{
+	cvmx_send_single(__cvmx_fau_iobdma_data
+			 (scraddr, value, 1, CVMX_FAU_OP_SIZE_64, reg));
+}
+
+/**
+ * Perform an async atomic 32 bit add after the current tag
+ * switch completes.
+ *
+ * @scraddr: Scratch memory byte address to put response in.  Must be
+ *	     8 byte aligned.  If a timeout occurs, the error bit (63)
+ *	     will be set. Otherwise the value of the register before
+ *	     the update will be returned
+ *
+ * @reg:     FAU atomic register to access. 0 <= reg < 2048.
+ *		  - Step by 4 for 32 bit access.
+ * @value:   Signed value to add.
+ *		  Note: Only the low 22 bits are available.
+ * Returns Placed in the scratch pad register
+ */
+static inline void cvmx_fau_async_tagwait_fetch_and_add32(uint64_t scraddr,
+							  cvmx_fau_reg_32_t reg,
+							  int32_t value)
+{
+	cvmx_send_single(__cvmx_fau_iobdma_data
+			 (scraddr, value, 1, CVMX_FAU_OP_SIZE_32, reg));
+}
+
+/**
+ * Perform an async atomic 16 bit add after the current tag
+ * switch completes.
+ *
+ * @scraddr: Scratch memory byte address to put response in.  Must be
+ *	     8 byte aligned.  If a timeout occurs, the error bit (63)
+ *	     will be set. Otherwise the value of the register before
+ *	     the update will be returned
+ *
+ * @reg:     FAU atomic register to access. 0 <= reg < 2048.
+ *		  - Step by 2 for 16 bit access.
+ * @value:   Signed value to add.
+ *
+ * Returns Placed in the scratch pad register
+ */
+static inline void cvmx_fau_async_tagwait_fetch_and_add16(uint64_t scraddr,
+							  cvmx_fau_reg_16_t reg,
+							  int16_t value)
+{
+	cvmx_send_single(__cvmx_fau_iobdma_data
+			 (scraddr, value, 1, CVMX_FAU_OP_SIZE_16, reg));
+}
+
+/**
+ * Perform an async atomic 8 bit add after the current tag
+ * switch completes.
+ *
+ * @scraddr: Scratch memory byte address to put response in.  Must be
+ *	     8 byte aligned.  If a timeout occurs, the error bit (63)
+ *	     will be set. Otherwise the value of the register before
+ *	     the update will be returned
+ *
+ * @reg:     FAU atomic register to access. 0 <= reg < 2048.
+ * @value:   Signed value to add.
+ *
+ * Returns Placed in the scratch pad register
+ */
+static inline void cvmx_fau_async_tagwait_fetch_and_add8(uint64_t scraddr,
+							 cvmx_fau_reg_8_t reg,
+							 int8_t value)
+{
+	cvmx_send_single(__cvmx_fau_iobdma_data
+			 (scraddr, value, 1, CVMX_FAU_OP_SIZE_8, reg));
+}
+
+/**
+ * Perform an atomic 64 bit add
+ *
+ * @reg:     FAU atomic register to access. 0 <= reg < 2048.
+ *		  - Step by 8 for 64 bit access.
+ * @value:   Signed value to add.
+ */
+static inline void cvmx_fau_atomic_add64(cvmx_fau_reg_64_t reg, int64_t value)
+{
+	cvmx_write64_int64(__cvmx_fau_store_address(0, reg), value);
+}
+
+/**
+ * Perform an atomic 32 bit add
+ *
+ * @reg:     FAU atomic register to access. 0 <= reg < 2048.
+ *		  - Step by 4 for 32 bit access.
+ * @value:   Signed value to add.
+ */
+static inline void cvmx_fau_atomic_add32(cvmx_fau_reg_32_t reg, int32_t value)
+{
+	reg ^= SWIZZLE_32;
+	cvmx_write64_int32(__cvmx_fau_store_address(0, reg), value);
+}
+
+/**
+ * Perform an atomic 16 bit add
+ *
+ * @reg:     FAU atomic register to access. 0 <= reg < 2048.
+ *		  - Step by 2 for 16 bit access.
+ * @value:   Signed value to add.
+ */
+static inline void cvmx_fau_atomic_add16(cvmx_fau_reg_16_t reg, int16_t value)
+{
+	reg ^= SWIZZLE_16;
+	cvmx_write64_int16(__cvmx_fau_store_address(0, reg), value);
+}
+
+/**
+ * Perform an atomic 8 bit add
+ *
+ * @reg:     FAU atomic register to access. 0 <= reg < 2048.
+ * @value:   Signed value to add.
+ */
+static inline void cvmx_fau_atomic_add8(cvmx_fau_reg_8_t reg, int8_t value)
+{
+	reg ^= SWIZZLE_8;
+	cvmx_write64_int8(__cvmx_fau_store_address(0, reg), value);
+}
+
+/**
+ * Perform an atomic 64 bit write
+ *
+ * @reg:     FAU atomic register to access. 0 <= reg < 2048.
+ *		  - Step by 8 for 64 bit access.
+ * @value:   Signed value to write.
+ */
+static inline void cvmx_fau_atomic_write64(cvmx_fau_reg_64_t reg, int64_t value)
+{
+	cvmx_write64_int64(__cvmx_fau_store_address(1, reg), value);
+}
+
+/**
+ * Perform an atomic 32 bit write
+ *
+ * @reg:     FAU atomic register to access. 0 <= reg < 2048.
+ *		  - Step by 4 for 32 bit access.
+ * @value:   Signed value to write.
+ */
+static inline void cvmx_fau_atomic_write32(cvmx_fau_reg_32_t reg, int32_t value)
+{
+	reg ^= SWIZZLE_32;
+	cvmx_write64_int32(__cvmx_fau_store_address(1, reg), value);
+}
+
+/**
+ * Perform an atomic 16 bit write
+ *
+ * @reg:     FAU atomic register to access. 0 <= reg < 2048.
+ *		  - Step by 2 for 16 bit access.
+ * @value:   Signed value to write.
+ */
+static inline void cvmx_fau_atomic_write16(cvmx_fau_reg_16_t reg, int16_t value)
+{
+	reg ^= SWIZZLE_16;
+	cvmx_write64_int16(__cvmx_fau_store_address(1, reg), value);
+}
+
+/**
+ * Perform an atomic 8 bit write
+ *
+ * @reg:     FAU atomic register to access. 0 <= reg < 2048.
+ * @value:   Signed value to write.
+ */
+static inline void cvmx_fau_atomic_write8(cvmx_fau_reg_8_t reg, int8_t value)
+{
+	reg ^= SWIZZLE_8;
+	cvmx_write64_int8(__cvmx_fau_store_address(1, reg), value);
+}
+
+#endif /* __CVMX_FAU_H__ */
diff --git a/arch/mips/include/asm/octeon/cvmx-fpa-defs.h b/arch/mips/include/asm/octeon/cvmx-fpa-defs.h
new file mode 100644
index 000000000..322943f7c
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-fpa-defs.h
@@ -0,0 +1,1252 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2012 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_FPA_DEFS_H__
+#define __CVMX_FPA_DEFS_H__
+
+#define CVMX_FPA_ADDR_RANGE_ERROR (CVMX_ADD_IO_SEG(0x0001180028000458ull))
+#define CVMX_FPA_BIST_STATUS (CVMX_ADD_IO_SEG(0x00011800280000E8ull))
+#define CVMX_FPA_CTL_STATUS (CVMX_ADD_IO_SEG(0x0001180028000050ull))
+#define CVMX_FPA_FPF0_MARKS (CVMX_ADD_IO_SEG(0x0001180028000000ull))
+#define CVMX_FPA_FPF0_SIZE (CVMX_ADD_IO_SEG(0x0001180028000058ull))
+#define CVMX_FPA_FPF1_MARKS CVMX_FPA_FPFX_MARKS(1)
+#define CVMX_FPA_FPF2_MARKS CVMX_FPA_FPFX_MARKS(2)
+#define CVMX_FPA_FPF3_MARKS CVMX_FPA_FPFX_MARKS(3)
+#define CVMX_FPA_FPF4_MARKS CVMX_FPA_FPFX_MARKS(4)
+#define CVMX_FPA_FPF5_MARKS CVMX_FPA_FPFX_MARKS(5)
+#define CVMX_FPA_FPF6_MARKS CVMX_FPA_FPFX_MARKS(6)
+#define CVMX_FPA_FPF7_MARKS CVMX_FPA_FPFX_MARKS(7)
+#define CVMX_FPA_FPF8_MARKS (CVMX_ADD_IO_SEG(0x0001180028000240ull))
+#define CVMX_FPA_FPF8_SIZE (CVMX_ADD_IO_SEG(0x0001180028000248ull))
+#define CVMX_FPA_FPFX_MARKS(offset) (CVMX_ADD_IO_SEG(0x0001180028000008ull) + ((offset) & 7) * 8 - 8*1)
+#define CVMX_FPA_FPFX_SIZE(offset) (CVMX_ADD_IO_SEG(0x0001180028000060ull) + ((offset) & 7) * 8 - 8*1)
+#define CVMX_FPA_INT_ENB (CVMX_ADD_IO_SEG(0x0001180028000048ull))
+#define CVMX_FPA_INT_SUM (CVMX_ADD_IO_SEG(0x0001180028000040ull))
+#define CVMX_FPA_PACKET_THRESHOLD (CVMX_ADD_IO_SEG(0x0001180028000460ull))
+#define CVMX_FPA_POOLX_END_ADDR(offset) (CVMX_ADD_IO_SEG(0x0001180028000358ull) + ((offset) & 15) * 8)
+#define CVMX_FPA_POOLX_START_ADDR(offset) (CVMX_ADD_IO_SEG(0x0001180028000258ull) + ((offset) & 15) * 8)
+#define CVMX_FPA_POOLX_THRESHOLD(offset) (CVMX_ADD_IO_SEG(0x0001180028000140ull) + ((offset) & 15) * 8)
+#define CVMX_FPA_QUE0_PAGE_INDEX CVMX_FPA_QUEX_PAGE_INDEX(0)
+#define CVMX_FPA_QUE1_PAGE_INDEX CVMX_FPA_QUEX_PAGE_INDEX(1)
+#define CVMX_FPA_QUE2_PAGE_INDEX CVMX_FPA_QUEX_PAGE_INDEX(2)
+#define CVMX_FPA_QUE3_PAGE_INDEX CVMX_FPA_QUEX_PAGE_INDEX(3)
+#define CVMX_FPA_QUE4_PAGE_INDEX CVMX_FPA_QUEX_PAGE_INDEX(4)
+#define CVMX_FPA_QUE5_PAGE_INDEX CVMX_FPA_QUEX_PAGE_INDEX(5)
+#define CVMX_FPA_QUE6_PAGE_INDEX CVMX_FPA_QUEX_PAGE_INDEX(6)
+#define CVMX_FPA_QUE7_PAGE_INDEX CVMX_FPA_QUEX_PAGE_INDEX(7)
+#define CVMX_FPA_QUE8_PAGE_INDEX (CVMX_ADD_IO_SEG(0x0001180028000250ull))
+#define CVMX_FPA_QUEX_AVAILABLE(offset) (CVMX_ADD_IO_SEG(0x0001180028000098ull) + ((offset) & 15) * 8)
+#define CVMX_FPA_QUEX_PAGE_INDEX(offset) (CVMX_ADD_IO_SEG(0x00011800280000F0ull) + ((offset) & 7) * 8)
+#define CVMX_FPA_QUE_ACT (CVMX_ADD_IO_SEG(0x0001180028000138ull))
+#define CVMX_FPA_QUE_EXP (CVMX_ADD_IO_SEG(0x0001180028000130ull))
+#define CVMX_FPA_WART_CTL (CVMX_ADD_IO_SEG(0x00011800280000D8ull))
+#define CVMX_FPA_WART_STATUS (CVMX_ADD_IO_SEG(0x00011800280000E0ull))
+#define CVMX_FPA_WQE_THRESHOLD (CVMX_ADD_IO_SEG(0x0001180028000468ull))
+#define CVMX_FPA_CLK_COUNT (CVMX_ADD_IO_SEG(0x00012800000000F0ull))
+
+union cvmx_fpa_addr_range_error {
+	uint64_t u64;
+	struct cvmx_fpa_addr_range_error_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_38_63:26;
+		uint64_t pool:5;
+		uint64_t addr:33;
+#else
+		uint64_t addr:33;
+		uint64_t pool:5;
+		uint64_t reserved_38_63:26;
+#endif
+	} s;
+};
+
+union cvmx_fpa_bist_status {
+	uint64_t u64;
+	struct cvmx_fpa_bist_status_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_5_63:59;
+		uint64_t frd:1;
+		uint64_t fpf0:1;
+		uint64_t fpf1:1;
+		uint64_t ffr:1;
+		uint64_t fdr:1;
+#else
+		uint64_t fdr:1;
+		uint64_t ffr:1;
+		uint64_t fpf1:1;
+		uint64_t fpf0:1;
+		uint64_t frd:1;
+		uint64_t reserved_5_63:59;
+#endif
+	} s;
+};
+
+union cvmx_fpa_ctl_status {
+	uint64_t u64;
+	struct cvmx_fpa_ctl_status_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_21_63:43;
+		uint64_t free_en:1;
+		uint64_t ret_off:1;
+		uint64_t req_off:1;
+		uint64_t reset:1;
+		uint64_t use_ldt:1;
+		uint64_t use_stt:1;
+		uint64_t enb:1;
+		uint64_t mem1_err:7;
+		uint64_t mem0_err:7;
+#else
+		uint64_t mem0_err:7;
+		uint64_t mem1_err:7;
+		uint64_t enb:1;
+		uint64_t use_stt:1;
+		uint64_t use_ldt:1;
+		uint64_t reset:1;
+		uint64_t req_off:1;
+		uint64_t ret_off:1;
+		uint64_t free_en:1;
+		uint64_t reserved_21_63:43;
+#endif
+	} s;
+	struct cvmx_fpa_ctl_status_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_18_63:46;
+		uint64_t reset:1;
+		uint64_t use_ldt:1;
+		uint64_t use_stt:1;
+		uint64_t enb:1;
+		uint64_t mem1_err:7;
+		uint64_t mem0_err:7;
+#else
+		uint64_t mem0_err:7;
+		uint64_t mem1_err:7;
+		uint64_t enb:1;
+		uint64_t use_stt:1;
+		uint64_t use_ldt:1;
+		uint64_t reset:1;
+		uint64_t reserved_18_63:46;
+#endif
+	} cn30xx;
+};
+
+union cvmx_fpa_fpfx_marks {
+	uint64_t u64;
+	struct cvmx_fpa_fpfx_marks_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_22_63:42;
+		uint64_t fpf_wr:11;
+		uint64_t fpf_rd:11;
+#else
+		uint64_t fpf_rd:11;
+		uint64_t fpf_wr:11;
+		uint64_t reserved_22_63:42;
+#endif
+	} s;
+};
+
+union cvmx_fpa_fpfx_size {
+	uint64_t u64;
+	struct cvmx_fpa_fpfx_size_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_11_63:53;
+		uint64_t fpf_siz:11;
+#else
+		uint64_t fpf_siz:11;
+		uint64_t reserved_11_63:53;
+#endif
+	} s;
+};
+
+union cvmx_fpa_fpf0_marks {
+	uint64_t u64;
+	struct cvmx_fpa_fpf0_marks_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_24_63:40;
+		uint64_t fpf_wr:12;
+		uint64_t fpf_rd:12;
+#else
+		uint64_t fpf_rd:12;
+		uint64_t fpf_wr:12;
+		uint64_t reserved_24_63:40;
+#endif
+	} s;
+};
+
+union cvmx_fpa_fpf0_size {
+	uint64_t u64;
+	struct cvmx_fpa_fpf0_size_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t fpf_siz:12;
+#else
+		uint64_t fpf_siz:12;
+		uint64_t reserved_12_63:52;
+#endif
+	} s;
+};
+
+union cvmx_fpa_fpf8_marks {
+	uint64_t u64;
+	struct cvmx_fpa_fpf8_marks_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_22_63:42;
+		uint64_t fpf_wr:11;
+		uint64_t fpf_rd:11;
+#else
+		uint64_t fpf_rd:11;
+		uint64_t fpf_wr:11;
+		uint64_t reserved_22_63:42;
+#endif
+	} s;
+};
+
+union cvmx_fpa_fpf8_size {
+	uint64_t u64;
+	struct cvmx_fpa_fpf8_size_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t fpf_siz:12;
+#else
+		uint64_t fpf_siz:12;
+		uint64_t reserved_12_63:52;
+#endif
+	} s;
+};
+
+union cvmx_fpa_int_enb {
+	uint64_t u64;
+	struct cvmx_fpa_int_enb_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_50_63:14;
+		uint64_t paddr_e:1;
+		uint64_t reserved_44_48:5;
+		uint64_t free7:1;
+		uint64_t free6:1;
+		uint64_t free5:1;
+		uint64_t free4:1;
+		uint64_t free3:1;
+		uint64_t free2:1;
+		uint64_t free1:1;
+		uint64_t free0:1;
+		uint64_t pool7th:1;
+		uint64_t pool6th:1;
+		uint64_t pool5th:1;
+		uint64_t pool4th:1;
+		uint64_t pool3th:1;
+		uint64_t pool2th:1;
+		uint64_t pool1th:1;
+		uint64_t pool0th:1;
+		uint64_t q7_perr:1;
+		uint64_t q7_coff:1;
+		uint64_t q7_und:1;
+		uint64_t q6_perr:1;
+		uint64_t q6_coff:1;
+		uint64_t q6_und:1;
+		uint64_t q5_perr:1;
+		uint64_t q5_coff:1;
+		uint64_t q5_und:1;
+		uint64_t q4_perr:1;
+		uint64_t q4_coff:1;
+		uint64_t q4_und:1;
+		uint64_t q3_perr:1;
+		uint64_t q3_coff:1;
+		uint64_t q3_und:1;
+		uint64_t q2_perr:1;
+		uint64_t q2_coff:1;
+		uint64_t q2_und:1;
+		uint64_t q1_perr:1;
+		uint64_t q1_coff:1;
+		uint64_t q1_und:1;
+		uint64_t q0_perr:1;
+		uint64_t q0_coff:1;
+		uint64_t q0_und:1;
+		uint64_t fed1_dbe:1;
+		uint64_t fed1_sbe:1;
+		uint64_t fed0_dbe:1;
+		uint64_t fed0_sbe:1;
+#else
+		uint64_t fed0_sbe:1;
+		uint64_t fed0_dbe:1;
+		uint64_t fed1_sbe:1;
+		uint64_t fed1_dbe:1;
+		uint64_t q0_und:1;
+		uint64_t q0_coff:1;
+		uint64_t q0_perr:1;
+		uint64_t q1_und:1;
+		uint64_t q1_coff:1;
+		uint64_t q1_perr:1;
+		uint64_t q2_und:1;
+		uint64_t q2_coff:1;
+		uint64_t q2_perr:1;
+		uint64_t q3_und:1;
+		uint64_t q3_coff:1;
+		uint64_t q3_perr:1;
+		uint64_t q4_und:1;
+		uint64_t q4_coff:1;
+		uint64_t q4_perr:1;
+		uint64_t q5_und:1;
+		uint64_t q5_coff:1;
+		uint64_t q5_perr:1;
+		uint64_t q6_und:1;
+		uint64_t q6_coff:1;
+		uint64_t q6_perr:1;
+		uint64_t q7_und:1;
+		uint64_t q7_coff:1;
+		uint64_t q7_perr:1;
+		uint64_t pool0th:1;
+		uint64_t pool1th:1;
+		uint64_t pool2th:1;
+		uint64_t pool3th:1;
+		uint64_t pool4th:1;
+		uint64_t pool5th:1;
+		uint64_t pool6th:1;
+		uint64_t pool7th:1;
+		uint64_t free0:1;
+		uint64_t free1:1;
+		uint64_t free2:1;
+		uint64_t free3:1;
+		uint64_t free4:1;
+		uint64_t free5:1;
+		uint64_t free6:1;
+		uint64_t free7:1;
+		uint64_t reserved_44_48:5;
+		uint64_t paddr_e:1;
+		uint64_t reserved_50_63:14;
+#endif
+	} s;
+	struct cvmx_fpa_int_enb_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_28_63:36;
+		uint64_t q7_perr:1;
+		uint64_t q7_coff:1;
+		uint64_t q7_und:1;
+		uint64_t q6_perr:1;
+		uint64_t q6_coff:1;
+		uint64_t q6_und:1;
+		uint64_t q5_perr:1;
+		uint64_t q5_coff:1;
+		uint64_t q5_und:1;
+		uint64_t q4_perr:1;
+		uint64_t q4_coff:1;
+		uint64_t q4_und:1;
+		uint64_t q3_perr:1;
+		uint64_t q3_coff:1;
+		uint64_t q3_und:1;
+		uint64_t q2_perr:1;
+		uint64_t q2_coff:1;
+		uint64_t q2_und:1;
+		uint64_t q1_perr:1;
+		uint64_t q1_coff:1;
+		uint64_t q1_und:1;
+		uint64_t q0_perr:1;
+		uint64_t q0_coff:1;
+		uint64_t q0_und:1;
+		uint64_t fed1_dbe:1;
+		uint64_t fed1_sbe:1;
+		uint64_t fed0_dbe:1;
+		uint64_t fed0_sbe:1;
+#else
+		uint64_t fed0_sbe:1;
+		uint64_t fed0_dbe:1;
+		uint64_t fed1_sbe:1;
+		uint64_t fed1_dbe:1;
+		uint64_t q0_und:1;
+		uint64_t q0_coff:1;
+		uint64_t q0_perr:1;
+		uint64_t q1_und:1;
+		uint64_t q1_coff:1;
+		uint64_t q1_perr:1;
+		uint64_t q2_und:1;
+		uint64_t q2_coff:1;
+		uint64_t q2_perr:1;
+		uint64_t q3_und:1;
+		uint64_t q3_coff:1;
+		uint64_t q3_perr:1;
+		uint64_t q4_und:1;
+		uint64_t q4_coff:1;
+		uint64_t q4_perr:1;
+		uint64_t q5_und:1;
+		uint64_t q5_coff:1;
+		uint64_t q5_perr:1;
+		uint64_t q6_und:1;
+		uint64_t q6_coff:1;
+		uint64_t q6_perr:1;
+		uint64_t q7_und:1;
+		uint64_t q7_coff:1;
+		uint64_t q7_perr:1;
+		uint64_t reserved_28_63:36;
+#endif
+	} cn30xx;
+	struct cvmx_fpa_int_enb_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_50_63:14;
+		uint64_t paddr_e:1;
+		uint64_t res_44:5;
+		uint64_t free7:1;
+		uint64_t free6:1;
+		uint64_t free5:1;
+		uint64_t free4:1;
+		uint64_t free3:1;
+		uint64_t free2:1;
+		uint64_t free1:1;
+		uint64_t free0:1;
+		uint64_t pool7th:1;
+		uint64_t pool6th:1;
+		uint64_t pool5th:1;
+		uint64_t pool4th:1;
+		uint64_t pool3th:1;
+		uint64_t pool2th:1;
+		uint64_t pool1th:1;
+		uint64_t pool0th:1;
+		uint64_t q7_perr:1;
+		uint64_t q7_coff:1;
+		uint64_t q7_und:1;
+		uint64_t q6_perr:1;
+		uint64_t q6_coff:1;
+		uint64_t q6_und:1;
+		uint64_t q5_perr:1;
+		uint64_t q5_coff:1;
+		uint64_t q5_und:1;
+		uint64_t q4_perr:1;
+		uint64_t q4_coff:1;
+		uint64_t q4_und:1;
+		uint64_t q3_perr:1;
+		uint64_t q3_coff:1;
+		uint64_t q3_und:1;
+		uint64_t q2_perr:1;
+		uint64_t q2_coff:1;
+		uint64_t q2_und:1;
+		uint64_t q1_perr:1;
+		uint64_t q1_coff:1;
+		uint64_t q1_und:1;
+		uint64_t q0_perr:1;
+		uint64_t q0_coff:1;
+		uint64_t q0_und:1;
+		uint64_t fed1_dbe:1;
+		uint64_t fed1_sbe:1;
+		uint64_t fed0_dbe:1;
+		uint64_t fed0_sbe:1;
+#else
+		uint64_t fed0_sbe:1;
+		uint64_t fed0_dbe:1;
+		uint64_t fed1_sbe:1;
+		uint64_t fed1_dbe:1;
+		uint64_t q0_und:1;
+		uint64_t q0_coff:1;
+		uint64_t q0_perr:1;
+		uint64_t q1_und:1;
+		uint64_t q1_coff:1;
+		uint64_t q1_perr:1;
+		uint64_t q2_und:1;
+		uint64_t q2_coff:1;
+		uint64_t q2_perr:1;
+		uint64_t q3_und:1;
+		uint64_t q3_coff:1;
+		uint64_t q3_perr:1;
+		uint64_t q4_und:1;
+		uint64_t q4_coff:1;
+		uint64_t q4_perr:1;
+		uint64_t q5_und:1;
+		uint64_t q5_coff:1;
+		uint64_t q5_perr:1;
+		uint64_t q6_und:1;
+		uint64_t q6_coff:1;
+		uint64_t q6_perr:1;
+		uint64_t q7_und:1;
+		uint64_t q7_coff:1;
+		uint64_t q7_perr:1;
+		uint64_t pool0th:1;
+		uint64_t pool1th:1;
+		uint64_t pool2th:1;
+		uint64_t pool3th:1;
+		uint64_t pool4th:1;
+		uint64_t pool5th:1;
+		uint64_t pool6th:1;
+		uint64_t pool7th:1;
+		uint64_t free0:1;
+		uint64_t free1:1;
+		uint64_t free2:1;
+		uint64_t free3:1;
+		uint64_t free4:1;
+		uint64_t free5:1;
+		uint64_t free6:1;
+		uint64_t free7:1;
+		uint64_t res_44:5;
+		uint64_t paddr_e:1;
+		uint64_t reserved_50_63:14;
+#endif
+	} cn61xx;
+	struct cvmx_fpa_int_enb_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_44_63:20;
+		uint64_t free7:1;
+		uint64_t free6:1;
+		uint64_t free5:1;
+		uint64_t free4:1;
+		uint64_t free3:1;
+		uint64_t free2:1;
+		uint64_t free1:1;
+		uint64_t free0:1;
+		uint64_t pool7th:1;
+		uint64_t pool6th:1;
+		uint64_t pool5th:1;
+		uint64_t pool4th:1;
+		uint64_t pool3th:1;
+		uint64_t pool2th:1;
+		uint64_t pool1th:1;
+		uint64_t pool0th:1;
+		uint64_t q7_perr:1;
+		uint64_t q7_coff:1;
+		uint64_t q7_und:1;
+		uint64_t q6_perr:1;
+		uint64_t q6_coff:1;
+		uint64_t q6_und:1;
+		uint64_t q5_perr:1;
+		uint64_t q5_coff:1;
+		uint64_t q5_und:1;
+		uint64_t q4_perr:1;
+		uint64_t q4_coff:1;
+		uint64_t q4_und:1;
+		uint64_t q3_perr:1;
+		uint64_t q3_coff:1;
+		uint64_t q3_und:1;
+		uint64_t q2_perr:1;
+		uint64_t q2_coff:1;
+		uint64_t q2_und:1;
+		uint64_t q1_perr:1;
+		uint64_t q1_coff:1;
+		uint64_t q1_und:1;
+		uint64_t q0_perr:1;
+		uint64_t q0_coff:1;
+		uint64_t q0_und:1;
+		uint64_t fed1_dbe:1;
+		uint64_t fed1_sbe:1;
+		uint64_t fed0_dbe:1;
+		uint64_t fed0_sbe:1;
+#else
+		uint64_t fed0_sbe:1;
+		uint64_t fed0_dbe:1;
+		uint64_t fed1_sbe:1;
+		uint64_t fed1_dbe:1;
+		uint64_t q0_und:1;
+		uint64_t q0_coff:1;
+		uint64_t q0_perr:1;
+		uint64_t q1_und:1;
+		uint64_t q1_coff:1;
+		uint64_t q1_perr:1;
+		uint64_t q2_und:1;
+		uint64_t q2_coff:1;
+		uint64_t q2_perr:1;
+		uint64_t q3_und:1;
+		uint64_t q3_coff:1;
+		uint64_t q3_perr:1;
+		uint64_t q4_und:1;
+		uint64_t q4_coff:1;
+		uint64_t q4_perr:1;
+		uint64_t q5_und:1;
+		uint64_t q5_coff:1;
+		uint64_t q5_perr:1;
+		uint64_t q6_und:1;
+		uint64_t q6_coff:1;
+		uint64_t q6_perr:1;
+		uint64_t q7_und:1;
+		uint64_t q7_coff:1;
+		uint64_t q7_perr:1;
+		uint64_t pool0th:1;
+		uint64_t pool1th:1;
+		uint64_t pool2th:1;
+		uint64_t pool3th:1;
+		uint64_t pool4th:1;
+		uint64_t pool5th:1;
+		uint64_t pool6th:1;
+		uint64_t pool7th:1;
+		uint64_t free0:1;
+		uint64_t free1:1;
+		uint64_t free2:1;
+		uint64_t free3:1;
+		uint64_t free4:1;
+		uint64_t free5:1;
+		uint64_t free6:1;
+		uint64_t free7:1;
+		uint64_t reserved_44_63:20;
+#endif
+	} cn63xx;
+	struct cvmx_fpa_int_enb_cn68xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_50_63:14;
+		uint64_t paddr_e:1;
+		uint64_t pool8th:1;
+		uint64_t q8_perr:1;
+		uint64_t q8_coff:1;
+		uint64_t q8_und:1;
+		uint64_t free8:1;
+		uint64_t free7:1;
+		uint64_t free6:1;
+		uint64_t free5:1;
+		uint64_t free4:1;
+		uint64_t free3:1;
+		uint64_t free2:1;
+		uint64_t free1:1;
+		uint64_t free0:1;
+		uint64_t pool7th:1;
+		uint64_t pool6th:1;
+		uint64_t pool5th:1;
+		uint64_t pool4th:1;
+		uint64_t pool3th:1;
+		uint64_t pool2th:1;
+		uint64_t pool1th:1;
+		uint64_t pool0th:1;
+		uint64_t q7_perr:1;
+		uint64_t q7_coff:1;
+		uint64_t q7_und:1;
+		uint64_t q6_perr:1;
+		uint64_t q6_coff:1;
+		uint64_t q6_und:1;
+		uint64_t q5_perr:1;
+		uint64_t q5_coff:1;
+		uint64_t q5_und:1;
+		uint64_t q4_perr:1;
+		uint64_t q4_coff:1;
+		uint64_t q4_und:1;
+		uint64_t q3_perr:1;
+		uint64_t q3_coff:1;
+		uint64_t q3_und:1;
+		uint64_t q2_perr:1;
+		uint64_t q2_coff:1;
+		uint64_t q2_und:1;
+		uint64_t q1_perr:1;
+		uint64_t q1_coff:1;
+		uint64_t q1_und:1;
+		uint64_t q0_perr:1;
+		uint64_t q0_coff:1;
+		uint64_t q0_und:1;
+		uint64_t fed1_dbe:1;
+		uint64_t fed1_sbe:1;
+		uint64_t fed0_dbe:1;
+		uint64_t fed0_sbe:1;
+#else
+		uint64_t fed0_sbe:1;
+		uint64_t fed0_dbe:1;
+		uint64_t fed1_sbe:1;
+		uint64_t fed1_dbe:1;
+		uint64_t q0_und:1;
+		uint64_t q0_coff:1;
+		uint64_t q0_perr:1;
+		uint64_t q1_und:1;
+		uint64_t q1_coff:1;
+		uint64_t q1_perr:1;
+		uint64_t q2_und:1;
+		uint64_t q2_coff:1;
+		uint64_t q2_perr:1;
+		uint64_t q3_und:1;
+		uint64_t q3_coff:1;
+		uint64_t q3_perr:1;
+		uint64_t q4_und:1;
+		uint64_t q4_coff:1;
+		uint64_t q4_perr:1;
+		uint64_t q5_und:1;
+		uint64_t q5_coff:1;
+		uint64_t q5_perr:1;
+		uint64_t q6_und:1;
+		uint64_t q6_coff:1;
+		uint64_t q6_perr:1;
+		uint64_t q7_und:1;
+		uint64_t q7_coff:1;
+		uint64_t q7_perr:1;
+		uint64_t pool0th:1;
+		uint64_t pool1th:1;
+		uint64_t pool2th:1;
+		uint64_t pool3th:1;
+		uint64_t pool4th:1;
+		uint64_t pool5th:1;
+		uint64_t pool6th:1;
+		uint64_t pool7th:1;
+		uint64_t free0:1;
+		uint64_t free1:1;
+		uint64_t free2:1;
+		uint64_t free3:1;
+		uint64_t free4:1;
+		uint64_t free5:1;
+		uint64_t free6:1;
+		uint64_t free7:1;
+		uint64_t free8:1;
+		uint64_t q8_und:1;
+		uint64_t q8_coff:1;
+		uint64_t q8_perr:1;
+		uint64_t pool8th:1;
+		uint64_t paddr_e:1;
+		uint64_t reserved_50_63:14;
+#endif
+	} cn68xx;
+};
+
+union cvmx_fpa_int_sum {
+	uint64_t u64;
+	struct cvmx_fpa_int_sum_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_50_63:14;
+		uint64_t paddr_e:1;
+		uint64_t pool8th:1;
+		uint64_t q8_perr:1;
+		uint64_t q8_coff:1;
+		uint64_t q8_und:1;
+		uint64_t free8:1;
+		uint64_t free7:1;
+		uint64_t free6:1;
+		uint64_t free5:1;
+		uint64_t free4:1;
+		uint64_t free3:1;
+		uint64_t free2:1;
+		uint64_t free1:1;
+		uint64_t free0:1;
+		uint64_t pool7th:1;
+		uint64_t pool6th:1;
+		uint64_t pool5th:1;
+		uint64_t pool4th:1;
+		uint64_t pool3th:1;
+		uint64_t pool2th:1;
+		uint64_t pool1th:1;
+		uint64_t pool0th:1;
+		uint64_t q7_perr:1;
+		uint64_t q7_coff:1;
+		uint64_t q7_und:1;
+		uint64_t q6_perr:1;
+		uint64_t q6_coff:1;
+		uint64_t q6_und:1;
+		uint64_t q5_perr:1;
+		uint64_t q5_coff:1;
+		uint64_t q5_und:1;
+		uint64_t q4_perr:1;
+		uint64_t q4_coff:1;
+		uint64_t q4_und:1;
+		uint64_t q3_perr:1;
+		uint64_t q3_coff:1;
+		uint64_t q3_und:1;
+		uint64_t q2_perr:1;
+		uint64_t q2_coff:1;
+		uint64_t q2_und:1;
+		uint64_t q1_perr:1;
+		uint64_t q1_coff:1;
+		uint64_t q1_und:1;
+		uint64_t q0_perr:1;
+		uint64_t q0_coff:1;
+		uint64_t q0_und:1;
+		uint64_t fed1_dbe:1;
+		uint64_t fed1_sbe:1;
+		uint64_t fed0_dbe:1;
+		uint64_t fed0_sbe:1;
+#else
+		uint64_t fed0_sbe:1;
+		uint64_t fed0_dbe:1;
+		uint64_t fed1_sbe:1;
+		uint64_t fed1_dbe:1;
+		uint64_t q0_und:1;
+		uint64_t q0_coff:1;
+		uint64_t q0_perr:1;
+		uint64_t q1_und:1;
+		uint64_t q1_coff:1;
+		uint64_t q1_perr:1;
+		uint64_t q2_und:1;
+		uint64_t q2_coff:1;
+		uint64_t q2_perr:1;
+		uint64_t q3_und:1;
+		uint64_t q3_coff:1;
+		uint64_t q3_perr:1;
+		uint64_t q4_und:1;
+		uint64_t q4_coff:1;
+		uint64_t q4_perr:1;
+		uint64_t q5_und:1;
+		uint64_t q5_coff:1;
+		uint64_t q5_perr:1;
+		uint64_t q6_und:1;
+		uint64_t q6_coff:1;
+		uint64_t q6_perr:1;
+		uint64_t q7_und:1;
+		uint64_t q7_coff:1;
+		uint64_t q7_perr:1;
+		uint64_t pool0th:1;
+		uint64_t pool1th:1;
+		uint64_t pool2th:1;
+		uint64_t pool3th:1;
+		uint64_t pool4th:1;
+		uint64_t pool5th:1;
+		uint64_t pool6th:1;
+		uint64_t pool7th:1;
+		uint64_t free0:1;
+		uint64_t free1:1;
+		uint64_t free2:1;
+		uint64_t free3:1;
+		uint64_t free4:1;
+		uint64_t free5:1;
+		uint64_t free6:1;
+		uint64_t free7:1;
+		uint64_t free8:1;
+		uint64_t q8_und:1;
+		uint64_t q8_coff:1;
+		uint64_t q8_perr:1;
+		uint64_t pool8th:1;
+		uint64_t paddr_e:1;
+		uint64_t reserved_50_63:14;
+#endif
+	} s;
+	struct cvmx_fpa_int_sum_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_28_63:36;
+		uint64_t q7_perr:1;
+		uint64_t q7_coff:1;
+		uint64_t q7_und:1;
+		uint64_t q6_perr:1;
+		uint64_t q6_coff:1;
+		uint64_t q6_und:1;
+		uint64_t q5_perr:1;
+		uint64_t q5_coff:1;
+		uint64_t q5_und:1;
+		uint64_t q4_perr:1;
+		uint64_t q4_coff:1;
+		uint64_t q4_und:1;
+		uint64_t q3_perr:1;
+		uint64_t q3_coff:1;
+		uint64_t q3_und:1;
+		uint64_t q2_perr:1;
+		uint64_t q2_coff:1;
+		uint64_t q2_und:1;
+		uint64_t q1_perr:1;
+		uint64_t q1_coff:1;
+		uint64_t q1_und:1;
+		uint64_t q0_perr:1;
+		uint64_t q0_coff:1;
+		uint64_t q0_und:1;
+		uint64_t fed1_dbe:1;
+		uint64_t fed1_sbe:1;
+		uint64_t fed0_dbe:1;
+		uint64_t fed0_sbe:1;
+#else
+		uint64_t fed0_sbe:1;
+		uint64_t fed0_dbe:1;
+		uint64_t fed1_sbe:1;
+		uint64_t fed1_dbe:1;
+		uint64_t q0_und:1;
+		uint64_t q0_coff:1;
+		uint64_t q0_perr:1;
+		uint64_t q1_und:1;
+		uint64_t q1_coff:1;
+		uint64_t q1_perr:1;
+		uint64_t q2_und:1;
+		uint64_t q2_coff:1;
+		uint64_t q2_perr:1;
+		uint64_t q3_und:1;
+		uint64_t q3_coff:1;
+		uint64_t q3_perr:1;
+		uint64_t q4_und:1;
+		uint64_t q4_coff:1;
+		uint64_t q4_perr:1;
+		uint64_t q5_und:1;
+		uint64_t q5_coff:1;
+		uint64_t q5_perr:1;
+		uint64_t q6_und:1;
+		uint64_t q6_coff:1;
+		uint64_t q6_perr:1;
+		uint64_t q7_und:1;
+		uint64_t q7_coff:1;
+		uint64_t q7_perr:1;
+		uint64_t reserved_28_63:36;
+#endif
+	} cn30xx;
+	struct cvmx_fpa_int_sum_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_50_63:14;
+		uint64_t paddr_e:1;
+		uint64_t reserved_44_48:5;
+		uint64_t free7:1;
+		uint64_t free6:1;
+		uint64_t free5:1;
+		uint64_t free4:1;
+		uint64_t free3:1;
+		uint64_t free2:1;
+		uint64_t free1:1;
+		uint64_t free0:1;
+		uint64_t pool7th:1;
+		uint64_t pool6th:1;
+		uint64_t pool5th:1;
+		uint64_t pool4th:1;
+		uint64_t pool3th:1;
+		uint64_t pool2th:1;
+		uint64_t pool1th:1;
+		uint64_t pool0th:1;
+		uint64_t q7_perr:1;
+		uint64_t q7_coff:1;
+		uint64_t q7_und:1;
+		uint64_t q6_perr:1;
+		uint64_t q6_coff:1;
+		uint64_t q6_und:1;
+		uint64_t q5_perr:1;
+		uint64_t q5_coff:1;
+		uint64_t q5_und:1;
+		uint64_t q4_perr:1;
+		uint64_t q4_coff:1;
+		uint64_t q4_und:1;
+		uint64_t q3_perr:1;
+		uint64_t q3_coff:1;
+		uint64_t q3_und:1;
+		uint64_t q2_perr:1;
+		uint64_t q2_coff:1;
+		uint64_t q2_und:1;
+		uint64_t q1_perr:1;
+		uint64_t q1_coff:1;
+		uint64_t q1_und:1;
+		uint64_t q0_perr:1;
+		uint64_t q0_coff:1;
+		uint64_t q0_und:1;
+		uint64_t fed1_dbe:1;
+		uint64_t fed1_sbe:1;
+		uint64_t fed0_dbe:1;
+		uint64_t fed0_sbe:1;
+#else
+		uint64_t fed0_sbe:1;
+		uint64_t fed0_dbe:1;
+		uint64_t fed1_sbe:1;
+		uint64_t fed1_dbe:1;
+		uint64_t q0_und:1;
+		uint64_t q0_coff:1;
+		uint64_t q0_perr:1;
+		uint64_t q1_und:1;
+		uint64_t q1_coff:1;
+		uint64_t q1_perr:1;
+		uint64_t q2_und:1;
+		uint64_t q2_coff:1;
+		uint64_t q2_perr:1;
+		uint64_t q3_und:1;
+		uint64_t q3_coff:1;
+		uint64_t q3_perr:1;
+		uint64_t q4_und:1;
+		uint64_t q4_coff:1;
+		uint64_t q4_perr:1;
+		uint64_t q5_und:1;
+		uint64_t q5_coff:1;
+		uint64_t q5_perr:1;
+		uint64_t q6_und:1;
+		uint64_t q6_coff:1;
+		uint64_t q6_perr:1;
+		uint64_t q7_und:1;
+		uint64_t q7_coff:1;
+		uint64_t q7_perr:1;
+		uint64_t pool0th:1;
+		uint64_t pool1th:1;
+		uint64_t pool2th:1;
+		uint64_t pool3th:1;
+		uint64_t pool4th:1;
+		uint64_t pool5th:1;
+		uint64_t pool6th:1;
+		uint64_t pool7th:1;
+		uint64_t free0:1;
+		uint64_t free1:1;
+		uint64_t free2:1;
+		uint64_t free3:1;
+		uint64_t free4:1;
+		uint64_t free5:1;
+		uint64_t free6:1;
+		uint64_t free7:1;
+		uint64_t reserved_44_48:5;
+		uint64_t paddr_e:1;
+		uint64_t reserved_50_63:14;
+#endif
+	} cn61xx;
+	struct cvmx_fpa_int_sum_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_44_63:20;
+		uint64_t free7:1;
+		uint64_t free6:1;
+		uint64_t free5:1;
+		uint64_t free4:1;
+		uint64_t free3:1;
+		uint64_t free2:1;
+		uint64_t free1:1;
+		uint64_t free0:1;
+		uint64_t pool7th:1;
+		uint64_t pool6th:1;
+		uint64_t pool5th:1;
+		uint64_t pool4th:1;
+		uint64_t pool3th:1;
+		uint64_t pool2th:1;
+		uint64_t pool1th:1;
+		uint64_t pool0th:1;
+		uint64_t q7_perr:1;
+		uint64_t q7_coff:1;
+		uint64_t q7_und:1;
+		uint64_t q6_perr:1;
+		uint64_t q6_coff:1;
+		uint64_t q6_und:1;
+		uint64_t q5_perr:1;
+		uint64_t q5_coff:1;
+		uint64_t q5_und:1;
+		uint64_t q4_perr:1;
+		uint64_t q4_coff:1;
+		uint64_t q4_und:1;
+		uint64_t q3_perr:1;
+		uint64_t q3_coff:1;
+		uint64_t q3_und:1;
+		uint64_t q2_perr:1;
+		uint64_t q2_coff:1;
+		uint64_t q2_und:1;
+		uint64_t q1_perr:1;
+		uint64_t q1_coff:1;
+		uint64_t q1_und:1;
+		uint64_t q0_perr:1;
+		uint64_t q0_coff:1;
+		uint64_t q0_und:1;
+		uint64_t fed1_dbe:1;
+		uint64_t fed1_sbe:1;
+		uint64_t fed0_dbe:1;
+		uint64_t fed0_sbe:1;
+#else
+		uint64_t fed0_sbe:1;
+		uint64_t fed0_dbe:1;
+		uint64_t fed1_sbe:1;
+		uint64_t fed1_dbe:1;
+		uint64_t q0_und:1;
+		uint64_t q0_coff:1;
+		uint64_t q0_perr:1;
+		uint64_t q1_und:1;
+		uint64_t q1_coff:1;
+		uint64_t q1_perr:1;
+		uint64_t q2_und:1;
+		uint64_t q2_coff:1;
+		uint64_t q2_perr:1;
+		uint64_t q3_und:1;
+		uint64_t q3_coff:1;
+		uint64_t q3_perr:1;
+		uint64_t q4_und:1;
+		uint64_t q4_coff:1;
+		uint64_t q4_perr:1;
+		uint64_t q5_und:1;
+		uint64_t q5_coff:1;
+		uint64_t q5_perr:1;
+		uint64_t q6_und:1;
+		uint64_t q6_coff:1;
+		uint64_t q6_perr:1;
+		uint64_t q7_und:1;
+		uint64_t q7_coff:1;
+		uint64_t q7_perr:1;
+		uint64_t pool0th:1;
+		uint64_t pool1th:1;
+		uint64_t pool2th:1;
+		uint64_t pool3th:1;
+		uint64_t pool4th:1;
+		uint64_t pool5th:1;
+		uint64_t pool6th:1;
+		uint64_t pool7th:1;
+		uint64_t free0:1;
+		uint64_t free1:1;
+		uint64_t free2:1;
+		uint64_t free3:1;
+		uint64_t free4:1;
+		uint64_t free5:1;
+		uint64_t free6:1;
+		uint64_t free7:1;
+		uint64_t reserved_44_63:20;
+#endif
+	} cn63xx;
+};
+
+union cvmx_fpa_packet_threshold {
+	uint64_t u64;
+	struct cvmx_fpa_packet_threshold_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t thresh:32;
+#else
+		uint64_t thresh:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_fpa_poolx_end_addr {
+	uint64_t u64;
+	struct cvmx_fpa_poolx_end_addr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_33_63:31;
+		uint64_t addr:33;
+#else
+		uint64_t addr:33;
+		uint64_t reserved_33_63:31;
+#endif
+	} s;
+};
+
+union cvmx_fpa_poolx_start_addr {
+	uint64_t u64;
+	struct cvmx_fpa_poolx_start_addr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_33_63:31;
+		uint64_t addr:33;
+#else
+		uint64_t addr:33;
+		uint64_t reserved_33_63:31;
+#endif
+	} s;
+};
+
+union cvmx_fpa_poolx_threshold {
+	uint64_t u64;
+	struct cvmx_fpa_poolx_threshold_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t thresh:32;
+#else
+		uint64_t thresh:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+	struct cvmx_fpa_poolx_threshold_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t thresh:29;
+#else
+		uint64_t thresh:29;
+		uint64_t reserved_29_63:35;
+#endif
+	} cn61xx;
+};
+
+union cvmx_fpa_quex_available {
+	uint64_t u64;
+	struct cvmx_fpa_quex_available_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t que_siz:32;
+#else
+		uint64_t que_siz:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+	struct cvmx_fpa_quex_available_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t que_siz:29;
+#else
+		uint64_t que_siz:29;
+		uint64_t reserved_29_63:35;
+#endif
+	} cn30xx;
+};
+
+union cvmx_fpa_quex_page_index {
+	uint64_t u64;
+	struct cvmx_fpa_quex_page_index_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_25_63:39;
+		uint64_t pg_num:25;
+#else
+		uint64_t pg_num:25;
+		uint64_t reserved_25_63:39;
+#endif
+	} s;
+};
+
+union cvmx_fpa_que8_page_index {
+	uint64_t u64;
+	struct cvmx_fpa_que8_page_index_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_25_63:39;
+		uint64_t pg_num:25;
+#else
+		uint64_t pg_num:25;
+		uint64_t reserved_25_63:39;
+#endif
+	} s;
+};
+
+union cvmx_fpa_que_act {
+	uint64_t u64;
+	struct cvmx_fpa_que_act_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t act_que:3;
+		uint64_t act_indx:26;
+#else
+		uint64_t act_indx:26;
+		uint64_t act_que:3;
+		uint64_t reserved_29_63:35;
+#endif
+	} s;
+};
+
+union cvmx_fpa_que_exp {
+	uint64_t u64;
+	struct cvmx_fpa_que_exp_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t exp_que:3;
+		uint64_t exp_indx:26;
+#else
+		uint64_t exp_indx:26;
+		uint64_t exp_que:3;
+		uint64_t reserved_29_63:35;
+#endif
+	} s;
+};
+
+union cvmx_fpa_wart_ctl {
+	uint64_t u64;
+	struct cvmx_fpa_wart_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t ctl:16;
+#else
+		uint64_t ctl:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_fpa_wart_status {
+	uint64_t u64;
+	struct cvmx_fpa_wart_status_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t status:32;
+#else
+		uint64_t status:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_fpa_wqe_threshold {
+	uint64_t u64;
+	struct cvmx_fpa_wqe_threshold_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t thresh:32;
+#else
+		uint64_t thresh:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-fpa.h b/arch/mips/include/asm/octeon/cvmx-fpa.h
new file mode 100644
index 000000000..f6dfcca97
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-fpa.h
@@ -0,0 +1,288 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/**
+ * @file
+ *
+ * Interface to the hardware Free Pool Allocator.
+ *
+ *
+ */
+
+#ifndef __CVMX_FPA_H__
+#define __CVMX_FPA_H__
+
+#include <linux/delay.h>
+
+#include <asm/octeon/cvmx-address.h>
+#include <asm/octeon/cvmx-fpa-defs.h>
+
+#define CVMX_FPA_NUM_POOLS	8
+#define CVMX_FPA_MIN_BLOCK_SIZE 128
+#define CVMX_FPA_ALIGNMENT	128
+
+/**
+ * Structure describing the data format used for stores to the FPA.
+ */
+typedef union {
+	uint64_t u64;
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		/*
+		 * the (64-bit word) location in scratchpad to write
+		 * to (if len != 0)
+		 */
+		uint64_t scraddr:8;
+		/* the number of words in the response (0 => no response) */
+		uint64_t len:8;
+		/* the ID of the device on the non-coherent bus */
+		uint64_t did:8;
+		/*
+		 * the address that will appear in the first tick on
+		 * the NCB bus.
+		 */
+		uint64_t addr:40;
+#else
+		uint64_t addr:40;
+		uint64_t did:8;
+		uint64_t len:8;
+		uint64_t scraddr:8;
+#endif
+	} s;
+} cvmx_fpa_iobdma_data_t;
+
+/**
+ * Structure describing the current state of a FPA pool.
+ */
+typedef struct {
+	/* Name it was created under */
+	const char *name;
+	/* Size of each block */
+	uint64_t size;
+	/* The base memory address of whole block */
+	void *base;
+	/* The number of elements in the pool at creation */
+	uint64_t starting_element_count;
+} cvmx_fpa_pool_info_t;
+
+/**
+ * Current state of all the pools. Use access functions
+ * instead of using it directly.
+ */
+extern cvmx_fpa_pool_info_t cvmx_fpa_pool_info[CVMX_FPA_NUM_POOLS];
+
+/* CSR typedefs have been moved to cvmx-csr-*.h */
+
+/**
+ * Return the name of the pool
+ *
+ * @pool:   Pool to get the name of
+ * Returns The name
+ */
+static inline const char *cvmx_fpa_get_name(uint64_t pool)
+{
+	return cvmx_fpa_pool_info[pool].name;
+}
+
+/**
+ * Return the base of the pool
+ *
+ * @pool:   Pool to get the base of
+ * Returns The base
+ */
+static inline void *cvmx_fpa_get_base(uint64_t pool)
+{
+	return cvmx_fpa_pool_info[pool].base;
+}
+
+/**
+ * Check if a pointer belongs to an FPA pool. Return non-zero
+ * if the supplied pointer is inside the memory controlled by
+ * an FPA pool.
+ *
+ * @pool:   Pool to check
+ * @ptr:    Pointer to check
+ * Returns Non-zero if pointer is in the pool. Zero if not
+ */
+static inline int cvmx_fpa_is_member(uint64_t pool, void *ptr)
+{
+	return ((ptr >= cvmx_fpa_pool_info[pool].base) &&
+		((char *)ptr <
+		 ((char *)(cvmx_fpa_pool_info[pool].base)) +
+		 cvmx_fpa_pool_info[pool].size *
+		 cvmx_fpa_pool_info[pool].starting_element_count));
+}
+
+/**
+ * Enable the FPA for use. Must be performed after any CSR
+ * configuration but before any other FPA functions.
+ */
+static inline void cvmx_fpa_enable(void)
+{
+	union cvmx_fpa_ctl_status status;
+
+	status.u64 = cvmx_read_csr(CVMX_FPA_CTL_STATUS);
+	if (status.s.enb) {
+		cvmx_dprintf
+		    ("Warning: Enabling FPA when FPA already enabled.\n");
+	}
+
+	/*
+	 * Do runtime check as we allow pass1 compiled code to run on
+	 * pass2 chips.
+	 */
+	if (cvmx_octeon_is_pass1()) {
+		union cvmx_fpa_fpfx_marks marks;
+		int i;
+		for (i = 1; i < 8; i++) {
+			marks.u64 =
+			    cvmx_read_csr(CVMX_FPA_FPF1_MARKS + (i - 1) * 8ull);
+			marks.s.fpf_wr = 0xe0;
+			cvmx_write_csr(CVMX_FPA_FPF1_MARKS + (i - 1) * 8ull,
+				       marks.u64);
+		}
+
+		/* Enforce a 10 cycle delay between config and enable */
+		__delay(10);
+	}
+
+	/* FIXME: CVMX_FPA_CTL_STATUS read is unmodelled */
+	status.u64 = 0;
+	status.s.enb = 1;
+	cvmx_write_csr(CVMX_FPA_CTL_STATUS, status.u64);
+}
+
+/**
+ * Get a new block from the FPA
+ *
+ * @pool:   Pool to get the block from
+ * Returns Pointer to the block or NULL on failure
+ */
+static inline void *cvmx_fpa_alloc(uint64_t pool)
+{
+	uint64_t address =
+	    cvmx_read_csr(CVMX_ADDR_DID(CVMX_FULL_DID(CVMX_OCT_DID_FPA, pool)));
+	if (address)
+		return cvmx_phys_to_ptr(address);
+	else
+		return NULL;
+}
+
+/**
+ * Asynchronously get a new block from the FPA
+ *
+ * @scr_addr: Local scratch address to put response in.	 This is a byte address,
+ *		    but must be 8 byte aligned.
+ * @pool:      Pool to get the block from
+ */
+static inline void cvmx_fpa_async_alloc(uint64_t scr_addr, uint64_t pool)
+{
+	cvmx_fpa_iobdma_data_t data;
+
+	/*
+	 * Hardware only uses 64 bit aligned locations, so convert
+	 * from byte address to 64-bit index
+	 */
+	data.s.scraddr = scr_addr >> 3;
+	data.s.len = 1;
+	data.s.did = CVMX_FULL_DID(CVMX_OCT_DID_FPA, pool);
+	data.s.addr = 0;
+	cvmx_send_single(data.u64);
+}
+
+/**
+ * Free a block allocated with a FPA pool.  Does NOT provide memory
+ * ordering in cases where the memory block was modified by the core.
+ *
+ * @ptr:    Block to free
+ * @pool:   Pool to put it in
+ * @num_cache_lines:
+ *		 Cache lines to invalidate
+ */
+static inline void cvmx_fpa_free_nosync(void *ptr, uint64_t pool,
+					uint64_t num_cache_lines)
+{
+	cvmx_addr_t newptr;
+	newptr.u64 = cvmx_ptr_to_phys(ptr);
+	newptr.sfilldidspace.didspace =
+	    CVMX_ADDR_DIDSPACE(CVMX_FULL_DID(CVMX_OCT_DID_FPA, pool));
+	/* Prevent GCC from reordering around free */
+	barrier();
+	/* value written is number of cache lines not written back */
+	cvmx_write_io(newptr.u64, num_cache_lines);
+}
+
+/**
+ * Free a block allocated with a FPA pool.  Provides required memory
+ * ordering in cases where memory block was modified by core.
+ *
+ * @ptr:    Block to free
+ * @pool:   Pool to put it in
+ * @num_cache_lines:
+ *		 Cache lines to invalidate
+ */
+static inline void cvmx_fpa_free(void *ptr, uint64_t pool,
+				 uint64_t num_cache_lines)
+{
+	cvmx_addr_t newptr;
+	newptr.u64 = cvmx_ptr_to_phys(ptr);
+	newptr.sfilldidspace.didspace =
+	    CVMX_ADDR_DIDSPACE(CVMX_FULL_DID(CVMX_OCT_DID_FPA, pool));
+	/*
+	 * Make sure that any previous writes to memory go out before
+	 * we free this buffer.	 This also serves as a barrier to
+	 * prevent GCC from reordering operations to after the
+	 * free.
+	 */
+	CVMX_SYNCWS;
+	/* value written is number of cache lines not written back */
+	cvmx_write_io(newptr.u64, num_cache_lines);
+}
+
+/**
+ * Shutdown a Memory pool and validate that it had all of
+ * the buffers originally placed in it. This should only be
+ * called by one processor after all hardware has finished
+ * using the pool.
+ *
+ * @pool:   Pool to shutdown
+ * Returns Zero on success
+ *	   - Positive is count of missing buffers
+ *	   - Negative is too many buffers or corrupted pointers
+ */
+extern uint64_t cvmx_fpa_shutdown_pool(uint64_t pool);
+
+/**
+ * Get the size of blocks controlled by the pool
+ * This is resolved to a constant at compile time.
+ *
+ * @pool:   Pool to access
+ * Returns Size of the block in bytes
+ */
+uint64_t cvmx_fpa_get_block_size(uint64_t pool);
+
+#endif /*  __CVM_FPA_H__ */
diff --git a/arch/mips/include/asm/octeon/cvmx-gmxx-defs.h b/arch/mips/include/asm/octeon/cvmx-gmxx-defs.h
new file mode 100644
index 000000000..bdba676f1
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-gmxx-defs.h
@@ -0,0 +1,2259 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (C) 2003-2018 Cavium, Inc.
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_GMXX_DEFS_H__
+#define __CVMX_GMXX_DEFS_H__
+
+static inline uint64_t CVMX_GMXX_HG2_CONTROL(unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000550ull) + (block_id) * 0x1000000ull;
+	}
+	return CVMX_ADD_IO_SEG(0x0001180008000550ull) + (block_id) * 0x8000000ull;
+}
+
+static inline uint64_t CVMX_GMXX_INF_MODE(unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800080007F8ull) + (block_id) * 0x1000000ull;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800080007F8ull) + (block_id) * 0x8000000ull;
+}
+
+static inline uint64_t CVMX_GMXX_PRTX_CFG(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN31XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000010ull) + ((offset) + (block_id) * 0x0ull) * 2048;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000010ull) + ((offset) + (block_id) * 0x2000ull) * 2048;
+	}
+	return CVMX_ADD_IO_SEG(0x0001180008000010ull) + ((offset) + (block_id) * 0x10000ull) * 2048;
+}
+
+static inline uint64_t CVMX_GMXX_RXX_ADR_CAM0(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN31XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000180ull) + ((offset) + (block_id) * 0x0ull) * 2048;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000180ull) + ((offset) + (block_id) * 0x2000ull) * 2048;
+	}
+	return CVMX_ADD_IO_SEG(0x0001180008000180ull) + ((offset) + (block_id) * 0x10000ull) * 2048;
+}
+
+static inline uint64_t CVMX_GMXX_RXX_ADR_CAM1(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN31XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000188ull) + ((offset) + (block_id) * 0x0ull) * 2048;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000188ull) + ((offset) + (block_id) * 0x2000ull) * 2048;
+	}
+	return CVMX_ADD_IO_SEG(0x0001180008000188ull) + ((offset) + (block_id) * 0x10000ull) * 2048;
+}
+
+static inline uint64_t CVMX_GMXX_RXX_ADR_CAM2(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN31XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000190ull) + ((offset) + (block_id) * 0x0ull) * 2048;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000190ull) + ((offset) + (block_id) * 0x2000ull) * 2048;
+	}
+	return CVMX_ADD_IO_SEG(0x0001180008000190ull) + ((offset) + (block_id) * 0x10000ull) * 2048;
+}
+
+static inline uint64_t CVMX_GMXX_RXX_ADR_CAM3(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN31XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000198ull) + ((offset) + (block_id) * 0x0ull) * 2048;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000198ull) + ((offset) + (block_id) * 0x2000ull) * 2048;
+	}
+	return CVMX_ADD_IO_SEG(0x0001180008000198ull) + ((offset) + (block_id) * 0x10000ull) * 2048;
+}
+
+static inline uint64_t CVMX_GMXX_RXX_ADR_CAM4(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN31XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800080001A0ull) + ((offset) + (block_id) * 0x0ull) * 2048;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800080001A0ull) + ((offset) + (block_id) * 0x2000ull) * 2048;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800080001A0ull) + ((offset) + (block_id) * 0x10000ull) * 2048;
+}
+
+static inline uint64_t CVMX_GMXX_RXX_ADR_CAM5(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN31XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800080001A8ull) + ((offset) + (block_id) * 0x0ull) * 2048;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800080001A8ull) + ((offset) + (block_id) * 0x2000ull) * 2048;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800080001A8ull) + ((offset) + (block_id) * 0x10000ull) * 2048;
+}
+
+static inline uint64_t CVMX_GMXX_RXX_ADR_CAM_EN(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN31XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000108ull) + ((offset) + (block_id) * 0x0ull) * 2048;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000108ull) + ((offset) + (block_id) * 0x2000ull) * 2048;
+	}
+	return CVMX_ADD_IO_SEG(0x0001180008000108ull) + ((offset) + (block_id) * 0x10000ull) * 2048;
+}
+
+static inline uint64_t CVMX_GMXX_RXX_ADR_CTL(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN31XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000100ull) + ((offset) + (block_id) * 0x0ull) * 2048;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000100ull) + ((offset) + (block_id) * 0x2000ull) * 2048;
+	}
+	return CVMX_ADD_IO_SEG(0x0001180008000100ull) + ((offset) + (block_id) * 0x10000ull) * 2048;
+}
+
+static inline uint64_t CVMX_GMXX_RXX_FRM_CTL(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN31XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000018ull) + ((offset) + (block_id) * 0x0ull) * 2048;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000018ull) + ((offset) + (block_id) * 0x2000ull) * 2048;
+	}
+	return CVMX_ADD_IO_SEG(0x0001180008000018ull) + ((offset) + (block_id) * 0x10000ull) * 2048;
+}
+
+#define CVMX_GMXX_RXX_FRM_MAX(offset, block_id) (CVMX_ADD_IO_SEG(0x0001180008000030ull) + (((offset) & 3) + ((block_id) & 1) * 0x10000ull) * 2048)
+#define CVMX_GMXX_RXX_FRM_MIN(offset, block_id) (CVMX_ADD_IO_SEG(0x0001180008000028ull) + (((offset) & 3) + ((block_id) & 1) * 0x10000ull) * 2048)
+
+static inline uint64_t CVMX_GMXX_RXX_INT_EN(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN31XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000008ull) + ((offset) + (block_id) * 0x0ull) * 2048;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000008ull) + ((offset) + (block_id) * 0x2000ull) * 2048;
+	}
+	return CVMX_ADD_IO_SEG(0x0001180008000008ull) + ((offset) + (block_id) * 0x10000ull) * 2048;
+}
+
+static inline uint64_t CVMX_GMXX_RXX_INT_REG(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN31XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000000ull) + ((offset) + (block_id) * 0x0ull) * 2048;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000000ull) + ((offset) + (block_id) * 0x2000ull) * 2048;
+	}
+	return CVMX_ADD_IO_SEG(0x0001180008000000ull) + ((offset) + (block_id) * 0x10000ull) * 2048;
+}
+
+static inline uint64_t CVMX_GMXX_RXX_JABBER(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN31XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000038ull) + ((offset) + (block_id) * 0x0ull) * 2048;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000038ull) + ((offset) + (block_id) * 0x2000ull) * 2048;
+	}
+	return CVMX_ADD_IO_SEG(0x0001180008000038ull) + ((offset) + (block_id) * 0x10000ull) * 2048;
+}
+
+#define CVMX_GMXX_RXX_RX_INBND(offset, block_id) (CVMX_ADD_IO_SEG(0x0001180008000060ull) + (((offset) & 3) + ((block_id) & 1) * 0x10000ull) * 2048)
+
+static inline uint64_t CVMX_GMXX_RX_PRTS(unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000410ull) + (block_id) * 0x1000000ull;
+	}
+	return CVMX_ADD_IO_SEG(0x0001180008000410ull) + (block_id) * 0x8000000ull;
+}
+
+static inline uint64_t CVMX_GMXX_RX_XAUI_CTL(unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000530ull) + (block_id) * 0x1000000ull;
+	}
+	return CVMX_ADD_IO_SEG(0x0001180008000530ull) + (block_id) * 0x8000000ull;
+}
+
+static inline uint64_t CVMX_GMXX_SMACX(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN31XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000230ull) + ((offset) + (block_id) * 0x0ull) * 2048;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000230ull) + ((offset) + (block_id) * 0x2000ull) * 2048;
+	}
+	return CVMX_ADD_IO_SEG(0x0001180008000230ull) + ((offset) + (block_id) * 0x10000ull) * 2048;
+}
+
+static inline uint64_t CVMX_GMXX_TXX_BURST(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN31XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000228ull) + ((offset) + (block_id) * 0x0ull) * 2048;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000228ull) + ((offset) + (block_id) * 0x2000ull) * 2048;
+	}
+	return CVMX_ADD_IO_SEG(0x0001180008000228ull) + ((offset) + (block_id) * 0x10000ull) * 2048;
+}
+
+#define CVMX_GMXX_TXX_CLK(offset, block_id) (CVMX_ADD_IO_SEG(0x0001180008000208ull) + (((offset) & 3) + ((block_id) & 1) * 0x10000ull) * 2048)
+static inline uint64_t CVMX_GMXX_TXX_CTL(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN31XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000270ull) + ((offset) + (block_id) * 0x0ull) * 2048;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000270ull) + ((offset) + (block_id) * 0x2000ull) * 2048;
+	}
+	return CVMX_ADD_IO_SEG(0x0001180008000270ull) + ((offset) + (block_id) * 0x10000ull) * 2048;
+}
+
+static inline uint64_t CVMX_GMXX_TXX_PAUSE_PKT_INTERVAL(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN31XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000248ull) + ((offset) + (block_id) * 0x0ull) * 2048;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000248ull) + ((offset) + (block_id) * 0x2000ull) * 2048;
+	}
+	return CVMX_ADD_IO_SEG(0x0001180008000248ull) + ((offset) + (block_id) * 0x10000ull) * 2048;
+}
+
+static inline uint64_t CVMX_GMXX_TXX_PAUSE_PKT_TIME(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN31XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000238ull) + ((offset) + (block_id) * 0x0ull) * 2048;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000238ull) + ((offset) + (block_id) * 0x2000ull) * 2048;
+	}
+	return CVMX_ADD_IO_SEG(0x0001180008000238ull) + ((offset) + (block_id) * 0x10000ull) * 2048;
+}
+
+static inline uint64_t CVMX_GMXX_TXX_SLOT(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN31XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000220ull) + ((offset) + (block_id) * 0x0ull) * 2048;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000220ull) + ((offset) + (block_id) * 0x2000ull) * 2048;
+	}
+	return CVMX_ADD_IO_SEG(0x0001180008000220ull) + ((offset) + (block_id) * 0x10000ull) * 2048;
+}
+
+static inline uint64_t CVMX_GMXX_TXX_THRESH(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN31XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000210ull) + ((offset) + (block_id) * 0x0ull) * 2048;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000210ull) + ((offset) + (block_id) * 0x2000ull) * 2048;
+	}
+	return CVMX_ADD_IO_SEG(0x0001180008000210ull) + ((offset) + (block_id) * 0x10000ull) * 2048;
+}
+
+static inline uint64_t CVMX_GMXX_TX_INT_EN(unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000508ull) + (block_id) * 0x1000000ull;
+	}
+	return CVMX_ADD_IO_SEG(0x0001180008000508ull) + (block_id) * 0x8000000ull;
+}
+
+static inline uint64_t CVMX_GMXX_TX_INT_REG(unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000500ull) + (block_id) * 0x1000000ull;
+	}
+	return CVMX_ADD_IO_SEG(0x0001180008000500ull) + (block_id) * 0x8000000ull;
+}
+
+static inline uint64_t CVMX_GMXX_TX_OVR_BP(unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800080004C8ull) + (block_id) * 0x1000000ull;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800080004C8ull) + (block_id) * 0x8000000ull;
+}
+
+static inline uint64_t CVMX_GMXX_TX_PRTS(unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000480ull) + (block_id) * 0x1000000ull;
+	}
+	return CVMX_ADD_IO_SEG(0x0001180008000480ull) + (block_id) * 0x8000000ull;
+}
+
+#define CVMX_GMXX_TX_SPI_CTL(block_id) (CVMX_ADD_IO_SEG(0x00011800080004C0ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_GMXX_TX_SPI_MAX(block_id) (CVMX_ADD_IO_SEG(0x00011800080004B0ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_GMXX_TX_SPI_THRESH(block_id) (CVMX_ADD_IO_SEG(0x00011800080004B8ull) + ((block_id) & 1) * 0x8000000ull)
+static inline uint64_t CVMX_GMXX_TX_XAUI_CTL(unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180008000528ull) + (block_id) * 0x1000000ull;
+	}
+	return CVMX_ADD_IO_SEG(0x0001180008000528ull) + (block_id) * 0x8000000ull;
+}
+
+void __cvmx_interrupt_gmxx_enable(int interface);
+
+union cvmx_gmxx_hg2_control {
+	uint64_t u64;
+	struct cvmx_gmxx_hg2_control_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_19_63:45;
+		uint64_t hg2tx_en:1;
+		uint64_t hg2rx_en:1;
+		uint64_t phys_en:1;
+		uint64_t logl_en:16;
+#else
+		uint64_t logl_en:16;
+		uint64_t phys_en:1;
+		uint64_t hg2rx_en:1;
+		uint64_t hg2tx_en:1;
+		uint64_t reserved_19_63:45;
+#endif
+	} s;
+};
+
+union cvmx_gmxx_inf_mode {
+	uint64_t u64;
+	struct cvmx_gmxx_inf_mode_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t rate:4;
+		uint64_t reserved_12_15:4;
+		uint64_t speed:4;
+		uint64_t reserved_7_7:1;
+		uint64_t mode:3;
+		uint64_t reserved_3_3:1;
+		uint64_t p0mii:1;
+		uint64_t en:1;
+		uint64_t type:1;
+#else
+		uint64_t type:1;
+		uint64_t en:1;
+		uint64_t p0mii:1;
+		uint64_t reserved_3_3:1;
+		uint64_t mode:3;
+		uint64_t reserved_7_7:1;
+		uint64_t speed:4;
+		uint64_t reserved_12_15:4;
+		uint64_t rate:4;
+		uint64_t reserved_20_63:44;
+#endif
+	} s;
+	struct cvmx_gmxx_inf_mode_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_3_63:61;
+		uint64_t p0mii:1;
+		uint64_t en:1;
+		uint64_t type:1;
+#else
+		uint64_t type:1;
+		uint64_t en:1;
+		uint64_t p0mii:1;
+		uint64_t reserved_3_63:61;
+#endif
+	} cn30xx;
+	struct cvmx_gmxx_inf_mode_cn31xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t en:1;
+		uint64_t type:1;
+#else
+		uint64_t type:1;
+		uint64_t en:1;
+		uint64_t reserved_2_63:62;
+#endif
+	} cn31xx;
+	struct cvmx_gmxx_inf_mode_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t speed:2;
+		uint64_t reserved_6_7:2;
+		uint64_t mode:2;
+		uint64_t reserved_2_3:2;
+		uint64_t en:1;
+		uint64_t type:1;
+#else
+		uint64_t type:1;
+		uint64_t en:1;
+		uint64_t reserved_2_3:2;
+		uint64_t mode:2;
+		uint64_t reserved_6_7:2;
+		uint64_t speed:2;
+		uint64_t reserved_10_63:54;
+#endif
+	} cn52xx;
+	struct cvmx_gmxx_inf_mode_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t speed:4;
+		uint64_t reserved_5_7:3;
+		uint64_t mode:1;
+		uint64_t reserved_2_3:2;
+		uint64_t en:1;
+		uint64_t type:1;
+#else
+		uint64_t type:1;
+		uint64_t en:1;
+		uint64_t reserved_2_3:2;
+		uint64_t mode:1;
+		uint64_t reserved_5_7:3;
+		uint64_t speed:4;
+		uint64_t reserved_12_63:52;
+#endif
+	} cn61xx;
+	struct cvmx_gmxx_inf_mode_cn66xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t rate:4;
+		uint64_t reserved_12_15:4;
+		uint64_t speed:4;
+		uint64_t reserved_5_7:3;
+		uint64_t mode:1;
+		uint64_t reserved_2_3:2;
+		uint64_t en:1;
+		uint64_t type:1;
+#else
+		uint64_t type:1;
+		uint64_t en:1;
+		uint64_t reserved_2_3:2;
+		uint64_t mode:1;
+		uint64_t reserved_5_7:3;
+		uint64_t speed:4;
+		uint64_t reserved_12_15:4;
+		uint64_t rate:4;
+		uint64_t reserved_20_63:44;
+#endif
+	} cn66xx;
+	struct cvmx_gmxx_inf_mode_cn68xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t speed:4;
+		uint64_t reserved_7_7:1;
+		uint64_t mode:3;
+		uint64_t reserved_2_3:2;
+		uint64_t en:1;
+		uint64_t type:1;
+#else
+		uint64_t type:1;
+		uint64_t en:1;
+		uint64_t reserved_2_3:2;
+		uint64_t mode:3;
+		uint64_t reserved_7_7:1;
+		uint64_t speed:4;
+		uint64_t reserved_12_63:52;
+#endif
+	} cn68xx;
+};
+
+union cvmx_gmxx_prtx_cfg {
+	uint64_t u64;
+	struct cvmx_gmxx_prtx_cfg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_22_63:42;
+		uint64_t pknd:6;
+		uint64_t reserved_14_15:2;
+		uint64_t tx_idle:1;
+		uint64_t rx_idle:1;
+		uint64_t reserved_9_11:3;
+		uint64_t speed_msb:1;
+		uint64_t reserved_4_7:4;
+		uint64_t slottime:1;
+		uint64_t duplex:1;
+		uint64_t speed:1;
+		uint64_t en:1;
+#else
+		uint64_t en:1;
+		uint64_t speed:1;
+		uint64_t duplex:1;
+		uint64_t slottime:1;
+		uint64_t reserved_4_7:4;
+		uint64_t speed_msb:1;
+		uint64_t reserved_9_11:3;
+		uint64_t rx_idle:1;
+		uint64_t tx_idle:1;
+		uint64_t reserved_14_15:2;
+		uint64_t pknd:6;
+		uint64_t reserved_22_63:42;
+#endif
+	} s;
+	struct cvmx_gmxx_prtx_cfg_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t slottime:1;
+		uint64_t duplex:1;
+		uint64_t speed:1;
+		uint64_t en:1;
+#else
+		uint64_t en:1;
+		uint64_t speed:1;
+		uint64_t duplex:1;
+		uint64_t slottime:1;
+		uint64_t reserved_4_63:60;
+#endif
+	} cn30xx;
+	struct cvmx_gmxx_prtx_cfg_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_14_63:50;
+		uint64_t tx_idle:1;
+		uint64_t rx_idle:1;
+		uint64_t reserved_9_11:3;
+		uint64_t speed_msb:1;
+		uint64_t reserved_4_7:4;
+		uint64_t slottime:1;
+		uint64_t duplex:1;
+		uint64_t speed:1;
+		uint64_t en:1;
+#else
+		uint64_t en:1;
+		uint64_t speed:1;
+		uint64_t duplex:1;
+		uint64_t slottime:1;
+		uint64_t reserved_4_7:4;
+		uint64_t speed_msb:1;
+		uint64_t reserved_9_11:3;
+		uint64_t rx_idle:1;
+		uint64_t tx_idle:1;
+		uint64_t reserved_14_63:50;
+#endif
+	} cn52xx;
+};
+
+union cvmx_gmxx_rxx_adr_ctl {
+	uint64_t u64;
+	struct cvmx_gmxx_rxx_adr_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t cam_mode:1;
+		uint64_t mcst:2;
+		uint64_t bcst:1;
+#else
+		uint64_t bcst:1;
+		uint64_t mcst:2;
+		uint64_t cam_mode:1;
+		uint64_t reserved_4_63:60;
+#endif
+	} s;
+};
+
+union cvmx_gmxx_rxx_frm_ctl {
+	uint64_t u64;
+	struct cvmx_gmxx_rxx_frm_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_13_63:51;
+		uint64_t ptp_mode:1;
+		uint64_t reserved_11_11:1;
+		uint64_t null_dis:1;
+		uint64_t pre_align:1;
+		uint64_t pad_len:1;
+		uint64_t vlan_len:1;
+		uint64_t pre_free:1;
+		uint64_t ctl_smac:1;
+		uint64_t ctl_mcst:1;
+		uint64_t ctl_bck:1;
+		uint64_t ctl_drp:1;
+		uint64_t pre_strp:1;
+		uint64_t pre_chk:1;
+#else
+		uint64_t pre_chk:1;
+		uint64_t pre_strp:1;
+		uint64_t ctl_drp:1;
+		uint64_t ctl_bck:1;
+		uint64_t ctl_mcst:1;
+		uint64_t ctl_smac:1;
+		uint64_t pre_free:1;
+		uint64_t vlan_len:1;
+		uint64_t pad_len:1;
+		uint64_t pre_align:1;
+		uint64_t null_dis:1;
+		uint64_t reserved_11_11:1;
+		uint64_t ptp_mode:1;
+		uint64_t reserved_13_63:51;
+#endif
+	} s;
+	struct cvmx_gmxx_rxx_frm_ctl_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_9_63:55;
+		uint64_t pad_len:1;
+		uint64_t vlan_len:1;
+		uint64_t pre_free:1;
+		uint64_t ctl_smac:1;
+		uint64_t ctl_mcst:1;
+		uint64_t ctl_bck:1;
+		uint64_t ctl_drp:1;
+		uint64_t pre_strp:1;
+		uint64_t pre_chk:1;
+#else
+		uint64_t pre_chk:1;
+		uint64_t pre_strp:1;
+		uint64_t ctl_drp:1;
+		uint64_t ctl_bck:1;
+		uint64_t ctl_mcst:1;
+		uint64_t ctl_smac:1;
+		uint64_t pre_free:1;
+		uint64_t vlan_len:1;
+		uint64_t pad_len:1;
+		uint64_t reserved_9_63:55;
+#endif
+	} cn30xx;
+	struct cvmx_gmxx_rxx_frm_ctl_cn31xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t vlan_len:1;
+		uint64_t pre_free:1;
+		uint64_t ctl_smac:1;
+		uint64_t ctl_mcst:1;
+		uint64_t ctl_bck:1;
+		uint64_t ctl_drp:1;
+		uint64_t pre_strp:1;
+		uint64_t pre_chk:1;
+#else
+		uint64_t pre_chk:1;
+		uint64_t pre_strp:1;
+		uint64_t ctl_drp:1;
+		uint64_t ctl_bck:1;
+		uint64_t ctl_mcst:1;
+		uint64_t ctl_smac:1;
+		uint64_t pre_free:1;
+		uint64_t vlan_len:1;
+		uint64_t reserved_8_63:56;
+#endif
+	} cn31xx;
+	struct cvmx_gmxx_rxx_frm_ctl_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_11_63:53;
+		uint64_t null_dis:1;
+		uint64_t pre_align:1;
+		uint64_t reserved_7_8:2;
+		uint64_t pre_free:1;
+		uint64_t ctl_smac:1;
+		uint64_t ctl_mcst:1;
+		uint64_t ctl_bck:1;
+		uint64_t ctl_drp:1;
+		uint64_t pre_strp:1;
+		uint64_t pre_chk:1;
+#else
+		uint64_t pre_chk:1;
+		uint64_t pre_strp:1;
+		uint64_t ctl_drp:1;
+		uint64_t ctl_bck:1;
+		uint64_t ctl_mcst:1;
+		uint64_t ctl_smac:1;
+		uint64_t pre_free:1;
+		uint64_t reserved_7_8:2;
+		uint64_t pre_align:1;
+		uint64_t null_dis:1;
+		uint64_t reserved_11_63:53;
+#endif
+	} cn50xx;
+	struct cvmx_gmxx_rxx_frm_ctl_cn56xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t pre_align:1;
+		uint64_t reserved_7_8:2;
+		uint64_t pre_free:1;
+		uint64_t ctl_smac:1;
+		uint64_t ctl_mcst:1;
+		uint64_t ctl_bck:1;
+		uint64_t ctl_drp:1;
+		uint64_t pre_strp:1;
+		uint64_t pre_chk:1;
+#else
+		uint64_t pre_chk:1;
+		uint64_t pre_strp:1;
+		uint64_t ctl_drp:1;
+		uint64_t ctl_bck:1;
+		uint64_t ctl_mcst:1;
+		uint64_t ctl_smac:1;
+		uint64_t pre_free:1;
+		uint64_t reserved_7_8:2;
+		uint64_t pre_align:1;
+		uint64_t reserved_10_63:54;
+#endif
+	} cn56xxp1;
+	struct cvmx_gmxx_rxx_frm_ctl_cn58xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_11_63:53;
+		uint64_t null_dis:1;
+		uint64_t pre_align:1;
+		uint64_t pad_len:1;
+		uint64_t vlan_len:1;
+		uint64_t pre_free:1;
+		uint64_t ctl_smac:1;
+		uint64_t ctl_mcst:1;
+		uint64_t ctl_bck:1;
+		uint64_t ctl_drp:1;
+		uint64_t pre_strp:1;
+		uint64_t pre_chk:1;
+#else
+		uint64_t pre_chk:1;
+		uint64_t pre_strp:1;
+		uint64_t ctl_drp:1;
+		uint64_t ctl_bck:1;
+		uint64_t ctl_mcst:1;
+		uint64_t ctl_smac:1;
+		uint64_t pre_free:1;
+		uint64_t vlan_len:1;
+		uint64_t pad_len:1;
+		uint64_t pre_align:1;
+		uint64_t null_dis:1;
+		uint64_t reserved_11_63:53;
+#endif
+	} cn58xx;
+	struct cvmx_gmxx_rxx_frm_ctl_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_13_63:51;
+		uint64_t ptp_mode:1;
+		uint64_t reserved_11_11:1;
+		uint64_t null_dis:1;
+		uint64_t pre_align:1;
+		uint64_t reserved_7_8:2;
+		uint64_t pre_free:1;
+		uint64_t ctl_smac:1;
+		uint64_t ctl_mcst:1;
+		uint64_t ctl_bck:1;
+		uint64_t ctl_drp:1;
+		uint64_t pre_strp:1;
+		uint64_t pre_chk:1;
+#else
+		uint64_t pre_chk:1;
+		uint64_t pre_strp:1;
+		uint64_t ctl_drp:1;
+		uint64_t ctl_bck:1;
+		uint64_t ctl_mcst:1;
+		uint64_t ctl_smac:1;
+		uint64_t pre_free:1;
+		uint64_t reserved_7_8:2;
+		uint64_t pre_align:1;
+		uint64_t null_dis:1;
+		uint64_t reserved_11_11:1;
+		uint64_t ptp_mode:1;
+		uint64_t reserved_13_63:51;
+#endif
+	} cn61xx;
+};
+
+union cvmx_gmxx_rxx_frm_max {
+	uint64_t u64;
+	struct cvmx_gmxx_rxx_frm_max_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t len:16;
+#else
+		uint64_t len:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_gmxx_rxx_frm_min {
+	uint64_t u64;
+	struct cvmx_gmxx_rxx_frm_min_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t len:16;
+#else
+		uint64_t len:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_gmxx_rxx_int_en {
+	uint64_t u64;
+	struct cvmx_gmxx_rxx_int_en_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t hg2cc:1;
+		uint64_t hg2fld:1;
+		uint64_t undat:1;
+		uint64_t uneop:1;
+		uint64_t unsop:1;
+		uint64_t bad_term:1;
+		uint64_t bad_seq:1;
+		uint64_t rem_fault:1;
+		uint64_t loc_fault:1;
+		uint64_t pause_drp:1;
+		uint64_t phy_dupx:1;
+		uint64_t phy_spd:1;
+		uint64_t phy_link:1;
+		uint64_t ifgerr:1;
+		uint64_t coldet:1;
+		uint64_t falerr:1;
+		uint64_t rsverr:1;
+		uint64_t pcterr:1;
+		uint64_t ovrerr:1;
+		uint64_t niberr:1;
+		uint64_t skperr:1;
+		uint64_t rcverr:1;
+		uint64_t lenerr:1;
+		uint64_t alnerr:1;
+		uint64_t fcserr:1;
+		uint64_t jabber:1;
+		uint64_t maxerr:1;
+		uint64_t carext:1;
+		uint64_t minerr:1;
+#else
+		uint64_t minerr:1;
+		uint64_t carext:1;
+		uint64_t maxerr:1;
+		uint64_t jabber:1;
+		uint64_t fcserr:1;
+		uint64_t alnerr:1;
+		uint64_t lenerr:1;
+		uint64_t rcverr:1;
+		uint64_t skperr:1;
+		uint64_t niberr:1;
+		uint64_t ovrerr:1;
+		uint64_t pcterr:1;
+		uint64_t rsverr:1;
+		uint64_t falerr:1;
+		uint64_t coldet:1;
+		uint64_t ifgerr:1;
+		uint64_t phy_link:1;
+		uint64_t phy_spd:1;
+		uint64_t phy_dupx:1;
+		uint64_t pause_drp:1;
+		uint64_t loc_fault:1;
+		uint64_t rem_fault:1;
+		uint64_t bad_seq:1;
+		uint64_t bad_term:1;
+		uint64_t unsop:1;
+		uint64_t uneop:1;
+		uint64_t undat:1;
+		uint64_t hg2fld:1;
+		uint64_t hg2cc:1;
+		uint64_t reserved_29_63:35;
+#endif
+	} s;
+	struct cvmx_gmxx_rxx_int_en_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_19_63:45;
+		uint64_t phy_dupx:1;
+		uint64_t phy_spd:1;
+		uint64_t phy_link:1;
+		uint64_t ifgerr:1;
+		uint64_t coldet:1;
+		uint64_t falerr:1;
+		uint64_t rsverr:1;
+		uint64_t pcterr:1;
+		uint64_t ovrerr:1;
+		uint64_t niberr:1;
+		uint64_t skperr:1;
+		uint64_t rcverr:1;
+		uint64_t lenerr:1;
+		uint64_t alnerr:1;
+		uint64_t fcserr:1;
+		uint64_t jabber:1;
+		uint64_t maxerr:1;
+		uint64_t carext:1;
+		uint64_t minerr:1;
+#else
+		uint64_t minerr:1;
+		uint64_t carext:1;
+		uint64_t maxerr:1;
+		uint64_t jabber:1;
+		uint64_t fcserr:1;
+		uint64_t alnerr:1;
+		uint64_t lenerr:1;
+		uint64_t rcverr:1;
+		uint64_t skperr:1;
+		uint64_t niberr:1;
+		uint64_t ovrerr:1;
+		uint64_t pcterr:1;
+		uint64_t rsverr:1;
+		uint64_t falerr:1;
+		uint64_t coldet:1;
+		uint64_t ifgerr:1;
+		uint64_t phy_link:1;
+		uint64_t phy_spd:1;
+		uint64_t phy_dupx:1;
+		uint64_t reserved_19_63:45;
+#endif
+	} cn30xx;
+	struct cvmx_gmxx_rxx_int_en_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t pause_drp:1;
+		uint64_t phy_dupx:1;
+		uint64_t phy_spd:1;
+		uint64_t phy_link:1;
+		uint64_t ifgerr:1;
+		uint64_t coldet:1;
+		uint64_t falerr:1;
+		uint64_t rsverr:1;
+		uint64_t pcterr:1;
+		uint64_t ovrerr:1;
+		uint64_t niberr:1;
+		uint64_t skperr:1;
+		uint64_t rcverr:1;
+		uint64_t reserved_6_6:1;
+		uint64_t alnerr:1;
+		uint64_t fcserr:1;
+		uint64_t jabber:1;
+		uint64_t reserved_2_2:1;
+		uint64_t carext:1;
+		uint64_t reserved_0_0:1;
+#else
+		uint64_t reserved_0_0:1;
+		uint64_t carext:1;
+		uint64_t reserved_2_2:1;
+		uint64_t jabber:1;
+		uint64_t fcserr:1;
+		uint64_t alnerr:1;
+		uint64_t reserved_6_6:1;
+		uint64_t rcverr:1;
+		uint64_t skperr:1;
+		uint64_t niberr:1;
+		uint64_t ovrerr:1;
+		uint64_t pcterr:1;
+		uint64_t rsverr:1;
+		uint64_t falerr:1;
+		uint64_t coldet:1;
+		uint64_t ifgerr:1;
+		uint64_t phy_link:1;
+		uint64_t phy_spd:1;
+		uint64_t phy_dupx:1;
+		uint64_t pause_drp:1;
+		uint64_t reserved_20_63:44;
+#endif
+	} cn50xx;
+	struct cvmx_gmxx_rxx_int_en_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t hg2cc:1;
+		uint64_t hg2fld:1;
+		uint64_t undat:1;
+		uint64_t uneop:1;
+		uint64_t unsop:1;
+		uint64_t bad_term:1;
+		uint64_t bad_seq:1;
+		uint64_t rem_fault:1;
+		uint64_t loc_fault:1;
+		uint64_t pause_drp:1;
+		uint64_t reserved_16_18:3;
+		uint64_t ifgerr:1;
+		uint64_t coldet:1;
+		uint64_t falerr:1;
+		uint64_t rsverr:1;
+		uint64_t pcterr:1;
+		uint64_t ovrerr:1;
+		uint64_t reserved_9_9:1;
+		uint64_t skperr:1;
+		uint64_t rcverr:1;
+		uint64_t reserved_5_6:2;
+		uint64_t fcserr:1;
+		uint64_t jabber:1;
+		uint64_t reserved_2_2:1;
+		uint64_t carext:1;
+		uint64_t reserved_0_0:1;
+#else
+		uint64_t reserved_0_0:1;
+		uint64_t carext:1;
+		uint64_t reserved_2_2:1;
+		uint64_t jabber:1;
+		uint64_t fcserr:1;
+		uint64_t reserved_5_6:2;
+		uint64_t rcverr:1;
+		uint64_t skperr:1;
+		uint64_t reserved_9_9:1;
+		uint64_t ovrerr:1;
+		uint64_t pcterr:1;
+		uint64_t rsverr:1;
+		uint64_t falerr:1;
+		uint64_t coldet:1;
+		uint64_t ifgerr:1;
+		uint64_t reserved_16_18:3;
+		uint64_t pause_drp:1;
+		uint64_t loc_fault:1;
+		uint64_t rem_fault:1;
+		uint64_t bad_seq:1;
+		uint64_t bad_term:1;
+		uint64_t unsop:1;
+		uint64_t uneop:1;
+		uint64_t undat:1;
+		uint64_t hg2fld:1;
+		uint64_t hg2cc:1;
+		uint64_t reserved_29_63:35;
+#endif
+	} cn52xx;
+	struct cvmx_gmxx_rxx_int_en_cn56xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_27_63:37;
+		uint64_t undat:1;
+		uint64_t uneop:1;
+		uint64_t unsop:1;
+		uint64_t bad_term:1;
+		uint64_t bad_seq:1;
+		uint64_t rem_fault:1;
+		uint64_t loc_fault:1;
+		uint64_t pause_drp:1;
+		uint64_t reserved_16_18:3;
+		uint64_t ifgerr:1;
+		uint64_t coldet:1;
+		uint64_t falerr:1;
+		uint64_t rsverr:1;
+		uint64_t pcterr:1;
+		uint64_t ovrerr:1;
+		uint64_t reserved_9_9:1;
+		uint64_t skperr:1;
+		uint64_t rcverr:1;
+		uint64_t reserved_5_6:2;
+		uint64_t fcserr:1;
+		uint64_t jabber:1;
+		uint64_t reserved_2_2:1;
+		uint64_t carext:1;
+		uint64_t reserved_0_0:1;
+#else
+		uint64_t reserved_0_0:1;
+		uint64_t carext:1;
+		uint64_t reserved_2_2:1;
+		uint64_t jabber:1;
+		uint64_t fcserr:1;
+		uint64_t reserved_5_6:2;
+		uint64_t rcverr:1;
+		uint64_t skperr:1;
+		uint64_t reserved_9_9:1;
+		uint64_t ovrerr:1;
+		uint64_t pcterr:1;
+		uint64_t rsverr:1;
+		uint64_t falerr:1;
+		uint64_t coldet:1;
+		uint64_t ifgerr:1;
+		uint64_t reserved_16_18:3;
+		uint64_t pause_drp:1;
+		uint64_t loc_fault:1;
+		uint64_t rem_fault:1;
+		uint64_t bad_seq:1;
+		uint64_t bad_term:1;
+		uint64_t unsop:1;
+		uint64_t uneop:1;
+		uint64_t undat:1;
+		uint64_t reserved_27_63:37;
+#endif
+	} cn56xxp1;
+	struct cvmx_gmxx_rxx_int_en_cn58xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t pause_drp:1;
+		uint64_t phy_dupx:1;
+		uint64_t phy_spd:1;
+		uint64_t phy_link:1;
+		uint64_t ifgerr:1;
+		uint64_t coldet:1;
+		uint64_t falerr:1;
+		uint64_t rsverr:1;
+		uint64_t pcterr:1;
+		uint64_t ovrerr:1;
+		uint64_t niberr:1;
+		uint64_t skperr:1;
+		uint64_t rcverr:1;
+		uint64_t lenerr:1;
+		uint64_t alnerr:1;
+		uint64_t fcserr:1;
+		uint64_t jabber:1;
+		uint64_t maxerr:1;
+		uint64_t carext:1;
+		uint64_t minerr:1;
+#else
+		uint64_t minerr:1;
+		uint64_t carext:1;
+		uint64_t maxerr:1;
+		uint64_t jabber:1;
+		uint64_t fcserr:1;
+		uint64_t alnerr:1;
+		uint64_t lenerr:1;
+		uint64_t rcverr:1;
+		uint64_t skperr:1;
+		uint64_t niberr:1;
+		uint64_t ovrerr:1;
+		uint64_t pcterr:1;
+		uint64_t rsverr:1;
+		uint64_t falerr:1;
+		uint64_t coldet:1;
+		uint64_t ifgerr:1;
+		uint64_t phy_link:1;
+		uint64_t phy_spd:1;
+		uint64_t phy_dupx:1;
+		uint64_t pause_drp:1;
+		uint64_t reserved_20_63:44;
+#endif
+	} cn58xx;
+	struct cvmx_gmxx_rxx_int_en_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t hg2cc:1;
+		uint64_t hg2fld:1;
+		uint64_t undat:1;
+		uint64_t uneop:1;
+		uint64_t unsop:1;
+		uint64_t bad_term:1;
+		uint64_t bad_seq:1;
+		uint64_t rem_fault:1;
+		uint64_t loc_fault:1;
+		uint64_t pause_drp:1;
+		uint64_t reserved_16_18:3;
+		uint64_t ifgerr:1;
+		uint64_t coldet:1;
+		uint64_t falerr:1;
+		uint64_t rsverr:1;
+		uint64_t pcterr:1;
+		uint64_t ovrerr:1;
+		uint64_t reserved_9_9:1;
+		uint64_t skperr:1;
+		uint64_t rcverr:1;
+		uint64_t reserved_5_6:2;
+		uint64_t fcserr:1;
+		uint64_t jabber:1;
+		uint64_t reserved_2_2:1;
+		uint64_t carext:1;
+		uint64_t minerr:1;
+#else
+		uint64_t minerr:1;
+		uint64_t carext:1;
+		uint64_t reserved_2_2:1;
+		uint64_t jabber:1;
+		uint64_t fcserr:1;
+		uint64_t reserved_5_6:2;
+		uint64_t rcverr:1;
+		uint64_t skperr:1;
+		uint64_t reserved_9_9:1;
+		uint64_t ovrerr:1;
+		uint64_t pcterr:1;
+		uint64_t rsverr:1;
+		uint64_t falerr:1;
+		uint64_t coldet:1;
+		uint64_t ifgerr:1;
+		uint64_t reserved_16_18:3;
+		uint64_t pause_drp:1;
+		uint64_t loc_fault:1;
+		uint64_t rem_fault:1;
+		uint64_t bad_seq:1;
+		uint64_t bad_term:1;
+		uint64_t unsop:1;
+		uint64_t uneop:1;
+		uint64_t undat:1;
+		uint64_t hg2fld:1;
+		uint64_t hg2cc:1;
+		uint64_t reserved_29_63:35;
+#endif
+	} cn61xx;
+};
+
+union cvmx_gmxx_rxx_int_reg {
+	uint64_t u64;
+	struct cvmx_gmxx_rxx_int_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t hg2cc:1;
+		uint64_t hg2fld:1;
+		uint64_t undat:1;
+		uint64_t uneop:1;
+		uint64_t unsop:1;
+		uint64_t bad_term:1;
+		uint64_t bad_seq:1;
+		uint64_t rem_fault:1;
+		uint64_t loc_fault:1;
+		uint64_t pause_drp:1;
+		uint64_t phy_dupx:1;
+		uint64_t phy_spd:1;
+		uint64_t phy_link:1;
+		uint64_t ifgerr:1;
+		uint64_t coldet:1;
+		uint64_t falerr:1;
+		uint64_t rsverr:1;
+		uint64_t pcterr:1;
+		uint64_t ovrerr:1;
+		uint64_t niberr:1;
+		uint64_t skperr:1;
+		uint64_t rcverr:1;
+		uint64_t lenerr:1;
+		uint64_t alnerr:1;
+		uint64_t fcserr:1;
+		uint64_t jabber:1;
+		uint64_t maxerr:1;
+		uint64_t carext:1;
+		uint64_t minerr:1;
+#else
+		uint64_t minerr:1;
+		uint64_t carext:1;
+		uint64_t maxerr:1;
+		uint64_t jabber:1;
+		uint64_t fcserr:1;
+		uint64_t alnerr:1;
+		uint64_t lenerr:1;
+		uint64_t rcverr:1;
+		uint64_t skperr:1;
+		uint64_t niberr:1;
+		uint64_t ovrerr:1;
+		uint64_t pcterr:1;
+		uint64_t rsverr:1;
+		uint64_t falerr:1;
+		uint64_t coldet:1;
+		uint64_t ifgerr:1;
+		uint64_t phy_link:1;
+		uint64_t phy_spd:1;
+		uint64_t phy_dupx:1;
+		uint64_t pause_drp:1;
+		uint64_t loc_fault:1;
+		uint64_t rem_fault:1;
+		uint64_t bad_seq:1;
+		uint64_t bad_term:1;
+		uint64_t unsop:1;
+		uint64_t uneop:1;
+		uint64_t undat:1;
+		uint64_t hg2fld:1;
+		uint64_t hg2cc:1;
+		uint64_t reserved_29_63:35;
+#endif
+	} s;
+	struct cvmx_gmxx_rxx_int_reg_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_19_63:45;
+		uint64_t phy_dupx:1;
+		uint64_t phy_spd:1;
+		uint64_t phy_link:1;
+		uint64_t ifgerr:1;
+		uint64_t coldet:1;
+		uint64_t falerr:1;
+		uint64_t rsverr:1;
+		uint64_t pcterr:1;
+		uint64_t ovrerr:1;
+		uint64_t niberr:1;
+		uint64_t skperr:1;
+		uint64_t rcverr:1;
+		uint64_t lenerr:1;
+		uint64_t alnerr:1;
+		uint64_t fcserr:1;
+		uint64_t jabber:1;
+		uint64_t maxerr:1;
+		uint64_t carext:1;
+		uint64_t minerr:1;
+#else
+		uint64_t minerr:1;
+		uint64_t carext:1;
+		uint64_t maxerr:1;
+		uint64_t jabber:1;
+		uint64_t fcserr:1;
+		uint64_t alnerr:1;
+		uint64_t lenerr:1;
+		uint64_t rcverr:1;
+		uint64_t skperr:1;
+		uint64_t niberr:1;
+		uint64_t ovrerr:1;
+		uint64_t pcterr:1;
+		uint64_t rsverr:1;
+		uint64_t falerr:1;
+		uint64_t coldet:1;
+		uint64_t ifgerr:1;
+		uint64_t phy_link:1;
+		uint64_t phy_spd:1;
+		uint64_t phy_dupx:1;
+		uint64_t reserved_19_63:45;
+#endif
+	} cn30xx;
+	struct cvmx_gmxx_rxx_int_reg_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t pause_drp:1;
+		uint64_t phy_dupx:1;
+		uint64_t phy_spd:1;
+		uint64_t phy_link:1;
+		uint64_t ifgerr:1;
+		uint64_t coldet:1;
+		uint64_t falerr:1;
+		uint64_t rsverr:1;
+		uint64_t pcterr:1;
+		uint64_t ovrerr:1;
+		uint64_t niberr:1;
+		uint64_t skperr:1;
+		uint64_t rcverr:1;
+		uint64_t reserved_6_6:1;
+		uint64_t alnerr:1;
+		uint64_t fcserr:1;
+		uint64_t jabber:1;
+		uint64_t reserved_2_2:1;
+		uint64_t carext:1;
+		uint64_t reserved_0_0:1;
+#else
+		uint64_t reserved_0_0:1;
+		uint64_t carext:1;
+		uint64_t reserved_2_2:1;
+		uint64_t jabber:1;
+		uint64_t fcserr:1;
+		uint64_t alnerr:1;
+		uint64_t reserved_6_6:1;
+		uint64_t rcverr:1;
+		uint64_t skperr:1;
+		uint64_t niberr:1;
+		uint64_t ovrerr:1;
+		uint64_t pcterr:1;
+		uint64_t rsverr:1;
+		uint64_t falerr:1;
+		uint64_t coldet:1;
+		uint64_t ifgerr:1;
+		uint64_t phy_link:1;
+		uint64_t phy_spd:1;
+		uint64_t phy_dupx:1;
+		uint64_t pause_drp:1;
+		uint64_t reserved_20_63:44;
+#endif
+	} cn50xx;
+	struct cvmx_gmxx_rxx_int_reg_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t hg2cc:1;
+		uint64_t hg2fld:1;
+		uint64_t undat:1;
+		uint64_t uneop:1;
+		uint64_t unsop:1;
+		uint64_t bad_term:1;
+		uint64_t bad_seq:1;
+		uint64_t rem_fault:1;
+		uint64_t loc_fault:1;
+		uint64_t pause_drp:1;
+		uint64_t reserved_16_18:3;
+		uint64_t ifgerr:1;
+		uint64_t coldet:1;
+		uint64_t falerr:1;
+		uint64_t rsverr:1;
+		uint64_t pcterr:1;
+		uint64_t ovrerr:1;
+		uint64_t reserved_9_9:1;
+		uint64_t skperr:1;
+		uint64_t rcverr:1;
+		uint64_t reserved_5_6:2;
+		uint64_t fcserr:1;
+		uint64_t jabber:1;
+		uint64_t reserved_2_2:1;
+		uint64_t carext:1;
+		uint64_t reserved_0_0:1;
+#else
+		uint64_t reserved_0_0:1;
+		uint64_t carext:1;
+		uint64_t reserved_2_2:1;
+		uint64_t jabber:1;
+		uint64_t fcserr:1;
+		uint64_t reserved_5_6:2;
+		uint64_t rcverr:1;
+		uint64_t skperr:1;
+		uint64_t reserved_9_9:1;
+		uint64_t ovrerr:1;
+		uint64_t pcterr:1;
+		uint64_t rsverr:1;
+		uint64_t falerr:1;
+		uint64_t coldet:1;
+		uint64_t ifgerr:1;
+		uint64_t reserved_16_18:3;
+		uint64_t pause_drp:1;
+		uint64_t loc_fault:1;
+		uint64_t rem_fault:1;
+		uint64_t bad_seq:1;
+		uint64_t bad_term:1;
+		uint64_t unsop:1;
+		uint64_t uneop:1;
+		uint64_t undat:1;
+		uint64_t hg2fld:1;
+		uint64_t hg2cc:1;
+		uint64_t reserved_29_63:35;
+#endif
+	} cn52xx;
+	struct cvmx_gmxx_rxx_int_reg_cn56xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_27_63:37;
+		uint64_t undat:1;
+		uint64_t uneop:1;
+		uint64_t unsop:1;
+		uint64_t bad_term:1;
+		uint64_t bad_seq:1;
+		uint64_t rem_fault:1;
+		uint64_t loc_fault:1;
+		uint64_t pause_drp:1;
+		uint64_t reserved_16_18:3;
+		uint64_t ifgerr:1;
+		uint64_t coldet:1;
+		uint64_t falerr:1;
+		uint64_t rsverr:1;
+		uint64_t pcterr:1;
+		uint64_t ovrerr:1;
+		uint64_t reserved_9_9:1;
+		uint64_t skperr:1;
+		uint64_t rcverr:1;
+		uint64_t reserved_5_6:2;
+		uint64_t fcserr:1;
+		uint64_t jabber:1;
+		uint64_t reserved_2_2:1;
+		uint64_t carext:1;
+		uint64_t reserved_0_0:1;
+#else
+		uint64_t reserved_0_0:1;
+		uint64_t carext:1;
+		uint64_t reserved_2_2:1;
+		uint64_t jabber:1;
+		uint64_t fcserr:1;
+		uint64_t reserved_5_6:2;
+		uint64_t rcverr:1;
+		uint64_t skperr:1;
+		uint64_t reserved_9_9:1;
+		uint64_t ovrerr:1;
+		uint64_t pcterr:1;
+		uint64_t rsverr:1;
+		uint64_t falerr:1;
+		uint64_t coldet:1;
+		uint64_t ifgerr:1;
+		uint64_t reserved_16_18:3;
+		uint64_t pause_drp:1;
+		uint64_t loc_fault:1;
+		uint64_t rem_fault:1;
+		uint64_t bad_seq:1;
+		uint64_t bad_term:1;
+		uint64_t unsop:1;
+		uint64_t uneop:1;
+		uint64_t undat:1;
+		uint64_t reserved_27_63:37;
+#endif
+	} cn56xxp1;
+	struct cvmx_gmxx_rxx_int_reg_cn58xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t pause_drp:1;
+		uint64_t phy_dupx:1;
+		uint64_t phy_spd:1;
+		uint64_t phy_link:1;
+		uint64_t ifgerr:1;
+		uint64_t coldet:1;
+		uint64_t falerr:1;
+		uint64_t rsverr:1;
+		uint64_t pcterr:1;
+		uint64_t ovrerr:1;
+		uint64_t niberr:1;
+		uint64_t skperr:1;
+		uint64_t rcverr:1;
+		uint64_t lenerr:1;
+		uint64_t alnerr:1;
+		uint64_t fcserr:1;
+		uint64_t jabber:1;
+		uint64_t maxerr:1;
+		uint64_t carext:1;
+		uint64_t minerr:1;
+#else
+		uint64_t minerr:1;
+		uint64_t carext:1;
+		uint64_t maxerr:1;
+		uint64_t jabber:1;
+		uint64_t fcserr:1;
+		uint64_t alnerr:1;
+		uint64_t lenerr:1;
+		uint64_t rcverr:1;
+		uint64_t skperr:1;
+		uint64_t niberr:1;
+		uint64_t ovrerr:1;
+		uint64_t pcterr:1;
+		uint64_t rsverr:1;
+		uint64_t falerr:1;
+		uint64_t coldet:1;
+		uint64_t ifgerr:1;
+		uint64_t phy_link:1;
+		uint64_t phy_spd:1;
+		uint64_t phy_dupx:1;
+		uint64_t pause_drp:1;
+		uint64_t reserved_20_63:44;
+#endif
+	} cn58xx;
+	struct cvmx_gmxx_rxx_int_reg_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t hg2cc:1;
+		uint64_t hg2fld:1;
+		uint64_t undat:1;
+		uint64_t uneop:1;
+		uint64_t unsop:1;
+		uint64_t bad_term:1;
+		uint64_t bad_seq:1;
+		uint64_t rem_fault:1;
+		uint64_t loc_fault:1;
+		uint64_t pause_drp:1;
+		uint64_t reserved_16_18:3;
+		uint64_t ifgerr:1;
+		uint64_t coldet:1;
+		uint64_t falerr:1;
+		uint64_t rsverr:1;
+		uint64_t pcterr:1;
+		uint64_t ovrerr:1;
+		uint64_t reserved_9_9:1;
+		uint64_t skperr:1;
+		uint64_t rcverr:1;
+		uint64_t reserved_5_6:2;
+		uint64_t fcserr:1;
+		uint64_t jabber:1;
+		uint64_t reserved_2_2:1;
+		uint64_t carext:1;
+		uint64_t minerr:1;
+#else
+		uint64_t minerr:1;
+		uint64_t carext:1;
+		uint64_t reserved_2_2:1;
+		uint64_t jabber:1;
+		uint64_t fcserr:1;
+		uint64_t reserved_5_6:2;
+		uint64_t rcverr:1;
+		uint64_t skperr:1;
+		uint64_t reserved_9_9:1;
+		uint64_t ovrerr:1;
+		uint64_t pcterr:1;
+		uint64_t rsverr:1;
+		uint64_t falerr:1;
+		uint64_t coldet:1;
+		uint64_t ifgerr:1;
+		uint64_t reserved_16_18:3;
+		uint64_t pause_drp:1;
+		uint64_t loc_fault:1;
+		uint64_t rem_fault:1;
+		uint64_t bad_seq:1;
+		uint64_t bad_term:1;
+		uint64_t unsop:1;
+		uint64_t uneop:1;
+		uint64_t undat:1;
+		uint64_t hg2fld:1;
+		uint64_t hg2cc:1;
+		uint64_t reserved_29_63:35;
+#endif
+	} cn61xx;
+};
+
+union cvmx_gmxx_rxx_jabber {
+	uint64_t u64;
+	struct cvmx_gmxx_rxx_jabber_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t cnt:16;
+#else
+		uint64_t cnt:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_gmxx_rxx_rx_inbnd {
+	uint64_t u64;
+	struct cvmx_gmxx_rxx_rx_inbnd_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t duplex:1;
+		uint64_t speed:2;
+		uint64_t status:1;
+#else
+		uint64_t status:1;
+		uint64_t speed:2;
+		uint64_t duplex:1;
+		uint64_t reserved_4_63:60;
+#endif
+	} s;
+};
+
+union cvmx_gmxx_rx_prts {
+	uint64_t u64;
+	struct cvmx_gmxx_rx_prts_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_3_63:61;
+		uint64_t prts:3;
+#else
+		uint64_t prts:3;
+		uint64_t reserved_3_63:61;
+#endif
+	} s;
+};
+
+union cvmx_gmxx_rx_xaui_ctl {
+	uint64_t u64;
+	struct cvmx_gmxx_rx_xaui_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t status:2;
+#else
+		uint64_t status:2;
+		uint64_t reserved_2_63:62;
+#endif
+	} s;
+};
+
+union cvmx_gmxx_txx_thresh {
+	uint64_t u64;
+	struct cvmx_gmxx_txx_thresh_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t cnt:10;
+#else
+		uint64_t cnt:10;
+		uint64_t reserved_10_63:54;
+#endif
+	} s;
+	struct cvmx_gmxx_txx_thresh_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t cnt:7;
+#else
+		uint64_t cnt:7;
+		uint64_t reserved_7_63:57;
+#endif
+	} cn30xx;
+	struct cvmx_gmxx_txx_thresh_cn38xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_9_63:55;
+		uint64_t cnt:9;
+#else
+		uint64_t cnt:9;
+		uint64_t reserved_9_63:55;
+#endif
+	} cn38xx;
+};
+
+union cvmx_gmxx_tx_int_en {
+	uint64_t u64;
+	struct cvmx_gmxx_tx_int_en_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_25_63:39;
+		uint64_t xchange:1;
+		uint64_t ptp_lost:4;
+		uint64_t late_col:4;
+		uint64_t xsdef:4;
+		uint64_t xscol:4;
+		uint64_t reserved_6_7:2;
+		uint64_t undflw:4;
+		uint64_t reserved_1_1:1;
+		uint64_t pko_nxa:1;
+#else
+		uint64_t pko_nxa:1;
+		uint64_t reserved_1_1:1;
+		uint64_t undflw:4;
+		uint64_t reserved_6_7:2;
+		uint64_t xscol:4;
+		uint64_t xsdef:4;
+		uint64_t late_col:4;
+		uint64_t ptp_lost:4;
+		uint64_t xchange:1;
+		uint64_t reserved_25_63:39;
+#endif
+	} s;
+	struct cvmx_gmxx_tx_int_en_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_19_63:45;
+		uint64_t late_col:3;
+		uint64_t reserved_15_15:1;
+		uint64_t xsdef:3;
+		uint64_t reserved_11_11:1;
+		uint64_t xscol:3;
+		uint64_t reserved_5_7:3;
+		uint64_t undflw:3;
+		uint64_t reserved_1_1:1;
+		uint64_t pko_nxa:1;
+#else
+		uint64_t pko_nxa:1;
+		uint64_t reserved_1_1:1;
+		uint64_t undflw:3;
+		uint64_t reserved_5_7:3;
+		uint64_t xscol:3;
+		uint64_t reserved_11_11:1;
+		uint64_t xsdef:3;
+		uint64_t reserved_15_15:1;
+		uint64_t late_col:3;
+		uint64_t reserved_19_63:45;
+#endif
+	} cn30xx;
+	struct cvmx_gmxx_tx_int_en_cn31xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_15_63:49;
+		uint64_t xsdef:3;
+		uint64_t reserved_11_11:1;
+		uint64_t xscol:3;
+		uint64_t reserved_5_7:3;
+		uint64_t undflw:3;
+		uint64_t reserved_1_1:1;
+		uint64_t pko_nxa:1;
+#else
+		uint64_t pko_nxa:1;
+		uint64_t reserved_1_1:1;
+		uint64_t undflw:3;
+		uint64_t reserved_5_7:3;
+		uint64_t xscol:3;
+		uint64_t reserved_11_11:1;
+		uint64_t xsdef:3;
+		uint64_t reserved_15_63:49;
+#endif
+	} cn31xx;
+	struct cvmx_gmxx_tx_int_en_cn38xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t late_col:4;
+		uint64_t xsdef:4;
+		uint64_t xscol:4;
+		uint64_t reserved_6_7:2;
+		uint64_t undflw:4;
+		uint64_t ncb_nxa:1;
+		uint64_t pko_nxa:1;
+#else
+		uint64_t pko_nxa:1;
+		uint64_t ncb_nxa:1;
+		uint64_t undflw:4;
+		uint64_t reserved_6_7:2;
+		uint64_t xscol:4;
+		uint64_t xsdef:4;
+		uint64_t late_col:4;
+		uint64_t reserved_20_63:44;
+#endif
+	} cn38xx;
+	struct cvmx_gmxx_tx_int_en_cn38xxp2 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t xsdef:4;
+		uint64_t xscol:4;
+		uint64_t reserved_6_7:2;
+		uint64_t undflw:4;
+		uint64_t ncb_nxa:1;
+		uint64_t pko_nxa:1;
+#else
+		uint64_t pko_nxa:1;
+		uint64_t ncb_nxa:1;
+		uint64_t undflw:4;
+		uint64_t reserved_6_7:2;
+		uint64_t xscol:4;
+		uint64_t xsdef:4;
+		uint64_t reserved_16_63:48;
+#endif
+	} cn38xxp2;
+	struct cvmx_gmxx_tx_int_en_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t late_col:4;
+		uint64_t xsdef:4;
+		uint64_t xscol:4;
+		uint64_t reserved_6_7:2;
+		uint64_t undflw:4;
+		uint64_t reserved_1_1:1;
+		uint64_t pko_nxa:1;
+#else
+		uint64_t pko_nxa:1;
+		uint64_t reserved_1_1:1;
+		uint64_t undflw:4;
+		uint64_t reserved_6_7:2;
+		uint64_t xscol:4;
+		uint64_t xsdef:4;
+		uint64_t late_col:4;
+		uint64_t reserved_20_63:44;
+#endif
+	} cn52xx;
+	struct cvmx_gmxx_tx_int_en_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_24_63:40;
+		uint64_t ptp_lost:4;
+		uint64_t late_col:4;
+		uint64_t xsdef:4;
+		uint64_t xscol:4;
+		uint64_t reserved_6_7:2;
+		uint64_t undflw:4;
+		uint64_t reserved_1_1:1;
+		uint64_t pko_nxa:1;
+#else
+		uint64_t pko_nxa:1;
+		uint64_t reserved_1_1:1;
+		uint64_t undflw:4;
+		uint64_t reserved_6_7:2;
+		uint64_t xscol:4;
+		uint64_t xsdef:4;
+		uint64_t late_col:4;
+		uint64_t ptp_lost:4;
+		uint64_t reserved_24_63:40;
+#endif
+	} cn63xx;
+	struct cvmx_gmxx_tx_int_en_cn68xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_25_63:39;
+		uint64_t xchange:1;
+		uint64_t ptp_lost:4;
+		uint64_t late_col:4;
+		uint64_t xsdef:4;
+		uint64_t xscol:4;
+		uint64_t reserved_6_7:2;
+		uint64_t undflw:4;
+		uint64_t pko_nxp:1;
+		uint64_t pko_nxa:1;
+#else
+		uint64_t pko_nxa:1;
+		uint64_t pko_nxp:1;
+		uint64_t undflw:4;
+		uint64_t reserved_6_7:2;
+		uint64_t xscol:4;
+		uint64_t xsdef:4;
+		uint64_t late_col:4;
+		uint64_t ptp_lost:4;
+		uint64_t xchange:1;
+		uint64_t reserved_25_63:39;
+#endif
+	} cn68xx;
+	struct cvmx_gmxx_tx_int_en_cnf71xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_25_63:39;
+		uint64_t xchange:1;
+		uint64_t reserved_22_23:2;
+		uint64_t ptp_lost:2;
+		uint64_t reserved_18_19:2;
+		uint64_t late_col:2;
+		uint64_t reserved_14_15:2;
+		uint64_t xsdef:2;
+		uint64_t reserved_10_11:2;
+		uint64_t xscol:2;
+		uint64_t reserved_4_7:4;
+		uint64_t undflw:2;
+		uint64_t reserved_1_1:1;
+		uint64_t pko_nxa:1;
+#else
+		uint64_t pko_nxa:1;
+		uint64_t reserved_1_1:1;
+		uint64_t undflw:2;
+		uint64_t reserved_4_7:4;
+		uint64_t xscol:2;
+		uint64_t reserved_10_11:2;
+		uint64_t xsdef:2;
+		uint64_t reserved_14_15:2;
+		uint64_t late_col:2;
+		uint64_t reserved_18_19:2;
+		uint64_t ptp_lost:2;
+		uint64_t reserved_22_23:2;
+		uint64_t xchange:1;
+		uint64_t reserved_25_63:39;
+#endif
+	} cnf71xx;
+};
+
+union cvmx_gmxx_tx_int_reg {
+	uint64_t u64;
+	struct cvmx_gmxx_tx_int_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_25_63:39;
+		uint64_t xchange:1;
+		uint64_t ptp_lost:4;
+		uint64_t late_col:4;
+		uint64_t xsdef:4;
+		uint64_t xscol:4;
+		uint64_t reserved_6_7:2;
+		uint64_t undflw:4;
+		uint64_t reserved_1_1:1;
+		uint64_t pko_nxa:1;
+#else
+		uint64_t pko_nxa:1;
+		uint64_t reserved_1_1:1;
+		uint64_t undflw:4;
+		uint64_t reserved_6_7:2;
+		uint64_t xscol:4;
+		uint64_t xsdef:4;
+		uint64_t late_col:4;
+		uint64_t ptp_lost:4;
+		uint64_t xchange:1;
+		uint64_t reserved_25_63:39;
+#endif
+	} s;
+	struct cvmx_gmxx_tx_int_reg_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_19_63:45;
+		uint64_t late_col:3;
+		uint64_t reserved_15_15:1;
+		uint64_t xsdef:3;
+		uint64_t reserved_11_11:1;
+		uint64_t xscol:3;
+		uint64_t reserved_5_7:3;
+		uint64_t undflw:3;
+		uint64_t reserved_1_1:1;
+		uint64_t pko_nxa:1;
+#else
+		uint64_t pko_nxa:1;
+		uint64_t reserved_1_1:1;
+		uint64_t undflw:3;
+		uint64_t reserved_5_7:3;
+		uint64_t xscol:3;
+		uint64_t reserved_11_11:1;
+		uint64_t xsdef:3;
+		uint64_t reserved_15_15:1;
+		uint64_t late_col:3;
+		uint64_t reserved_19_63:45;
+#endif
+	} cn30xx;
+	struct cvmx_gmxx_tx_int_reg_cn31xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_15_63:49;
+		uint64_t xsdef:3;
+		uint64_t reserved_11_11:1;
+		uint64_t xscol:3;
+		uint64_t reserved_5_7:3;
+		uint64_t undflw:3;
+		uint64_t reserved_1_1:1;
+		uint64_t pko_nxa:1;
+#else
+		uint64_t pko_nxa:1;
+		uint64_t reserved_1_1:1;
+		uint64_t undflw:3;
+		uint64_t reserved_5_7:3;
+		uint64_t xscol:3;
+		uint64_t reserved_11_11:1;
+		uint64_t xsdef:3;
+		uint64_t reserved_15_63:49;
+#endif
+	} cn31xx;
+	struct cvmx_gmxx_tx_int_reg_cn38xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t late_col:4;
+		uint64_t xsdef:4;
+		uint64_t xscol:4;
+		uint64_t reserved_6_7:2;
+		uint64_t undflw:4;
+		uint64_t ncb_nxa:1;
+		uint64_t pko_nxa:1;
+#else
+		uint64_t pko_nxa:1;
+		uint64_t ncb_nxa:1;
+		uint64_t undflw:4;
+		uint64_t reserved_6_7:2;
+		uint64_t xscol:4;
+		uint64_t xsdef:4;
+		uint64_t late_col:4;
+		uint64_t reserved_20_63:44;
+#endif
+	} cn38xx;
+	struct cvmx_gmxx_tx_int_reg_cn38xxp2 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t xsdef:4;
+		uint64_t xscol:4;
+		uint64_t reserved_6_7:2;
+		uint64_t undflw:4;
+		uint64_t ncb_nxa:1;
+		uint64_t pko_nxa:1;
+#else
+		uint64_t pko_nxa:1;
+		uint64_t ncb_nxa:1;
+		uint64_t undflw:4;
+		uint64_t reserved_6_7:2;
+		uint64_t xscol:4;
+		uint64_t xsdef:4;
+		uint64_t reserved_16_63:48;
+#endif
+	} cn38xxp2;
+	struct cvmx_gmxx_tx_int_reg_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t late_col:4;
+		uint64_t xsdef:4;
+		uint64_t xscol:4;
+		uint64_t reserved_6_7:2;
+		uint64_t undflw:4;
+		uint64_t reserved_1_1:1;
+		uint64_t pko_nxa:1;
+#else
+		uint64_t pko_nxa:1;
+		uint64_t reserved_1_1:1;
+		uint64_t undflw:4;
+		uint64_t reserved_6_7:2;
+		uint64_t xscol:4;
+		uint64_t xsdef:4;
+		uint64_t late_col:4;
+		uint64_t reserved_20_63:44;
+#endif
+	} cn52xx;
+	struct cvmx_gmxx_tx_int_reg_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_24_63:40;
+		uint64_t ptp_lost:4;
+		uint64_t late_col:4;
+		uint64_t xsdef:4;
+		uint64_t xscol:4;
+		uint64_t reserved_6_7:2;
+		uint64_t undflw:4;
+		uint64_t reserved_1_1:1;
+		uint64_t pko_nxa:1;
+#else
+		uint64_t pko_nxa:1;
+		uint64_t reserved_1_1:1;
+		uint64_t undflw:4;
+		uint64_t reserved_6_7:2;
+		uint64_t xscol:4;
+		uint64_t xsdef:4;
+		uint64_t late_col:4;
+		uint64_t ptp_lost:4;
+		uint64_t reserved_24_63:40;
+#endif
+	} cn63xx;
+	struct cvmx_gmxx_tx_int_reg_cn68xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_25_63:39;
+		uint64_t xchange:1;
+		uint64_t ptp_lost:4;
+		uint64_t late_col:4;
+		uint64_t xsdef:4;
+		uint64_t xscol:4;
+		uint64_t reserved_6_7:2;
+		uint64_t undflw:4;
+		uint64_t pko_nxp:1;
+		uint64_t pko_nxa:1;
+#else
+		uint64_t pko_nxa:1;
+		uint64_t pko_nxp:1;
+		uint64_t undflw:4;
+		uint64_t reserved_6_7:2;
+		uint64_t xscol:4;
+		uint64_t xsdef:4;
+		uint64_t late_col:4;
+		uint64_t ptp_lost:4;
+		uint64_t xchange:1;
+		uint64_t reserved_25_63:39;
+#endif
+	} cn68xx;
+	struct cvmx_gmxx_tx_int_reg_cnf71xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_25_63:39;
+		uint64_t xchange:1;
+		uint64_t reserved_22_23:2;
+		uint64_t ptp_lost:2;
+		uint64_t reserved_18_19:2;
+		uint64_t late_col:2;
+		uint64_t reserved_14_15:2;
+		uint64_t xsdef:2;
+		uint64_t reserved_10_11:2;
+		uint64_t xscol:2;
+		uint64_t reserved_4_7:4;
+		uint64_t undflw:2;
+		uint64_t reserved_1_1:1;
+		uint64_t pko_nxa:1;
+#else
+		uint64_t pko_nxa:1;
+		uint64_t reserved_1_1:1;
+		uint64_t undflw:2;
+		uint64_t reserved_4_7:4;
+		uint64_t xscol:2;
+		uint64_t reserved_10_11:2;
+		uint64_t xsdef:2;
+		uint64_t reserved_14_15:2;
+		uint64_t late_col:2;
+		uint64_t reserved_18_19:2;
+		uint64_t ptp_lost:2;
+		uint64_t reserved_22_23:2;
+		uint64_t xchange:1;
+		uint64_t reserved_25_63:39;
+#endif
+	} cnf71xx;
+};
+
+union cvmx_gmxx_tx_ovr_bp {
+	uint64_t u64;
+	struct cvmx_gmxx_tx_ovr_bp_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t tx_prt_bp:16;
+		uint64_t reserved_12_31:20;
+		uint64_t en:4;
+		uint64_t bp:4;
+		uint64_t ign_full:4;
+#else
+		uint64_t ign_full:4;
+		uint64_t bp:4;
+		uint64_t en:4;
+		uint64_t reserved_12_31:20;
+		uint64_t tx_prt_bp:16;
+		uint64_t reserved_48_63:16;
+#endif
+	} s;
+	struct cvmx_gmxx_tx_ovr_bp_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_11_63:53;
+		uint64_t en:3;
+		uint64_t reserved_7_7:1;
+		uint64_t bp:3;
+		uint64_t reserved_3_3:1;
+		uint64_t ign_full:3;
+#else
+		uint64_t ign_full:3;
+		uint64_t reserved_3_3:1;
+		uint64_t bp:3;
+		uint64_t reserved_7_7:1;
+		uint64_t en:3;
+		uint64_t reserved_11_63:53;
+#endif
+	} cn30xx;
+	struct cvmx_gmxx_tx_ovr_bp_cn38xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t en:4;
+		uint64_t bp:4;
+		uint64_t ign_full:4;
+#else
+		uint64_t ign_full:4;
+		uint64_t bp:4;
+		uint64_t en:4;
+		uint64_t reserved_12_63:52;
+#endif
+	} cn38xx;
+	struct cvmx_gmxx_tx_ovr_bp_cnf71xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t tx_prt_bp:16;
+		uint64_t reserved_10_31:22;
+		uint64_t en:2;
+		uint64_t reserved_6_7:2;
+		uint64_t bp:2;
+		uint64_t reserved_2_3:2;
+		uint64_t ign_full:2;
+#else
+		uint64_t ign_full:2;
+		uint64_t reserved_2_3:2;
+		uint64_t bp:2;
+		uint64_t reserved_6_7:2;
+		uint64_t en:2;
+		uint64_t reserved_10_31:22;
+		uint64_t tx_prt_bp:16;
+		uint64_t reserved_48_63:16;
+#endif
+	} cnf71xx;
+};
+
+union cvmx_gmxx_tx_prts {
+	uint64_t u64;
+	struct cvmx_gmxx_tx_prts_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_5_63:59;
+		uint64_t prts:5;
+#else
+		uint64_t prts:5;
+		uint64_t reserved_5_63:59;
+#endif
+	} s;
+};
+
+union cvmx_gmxx_tx_spi_ctl {
+	uint64_t u64;
+	struct cvmx_gmxx_tx_spi_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t tpa_clr:1;
+		uint64_t cont_pkt:1;
+#else
+		uint64_t cont_pkt:1;
+		uint64_t tpa_clr:1;
+		uint64_t reserved_2_63:62;
+#endif
+	} s;
+};
+
+union cvmx_gmxx_tx_spi_max {
+	uint64_t u64;
+	struct cvmx_gmxx_tx_spi_max_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_23_63:41;
+		uint64_t slice:7;
+		uint64_t max2:8;
+		uint64_t max1:8;
+#else
+		uint64_t max1:8;
+		uint64_t max2:8;
+		uint64_t slice:7;
+		uint64_t reserved_23_63:41;
+#endif
+	} s;
+	struct cvmx_gmxx_tx_spi_max_cn38xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t max2:8;
+		uint64_t max1:8;
+#else
+		uint64_t max1:8;
+		uint64_t max2:8;
+		uint64_t reserved_16_63:48;
+#endif
+	} cn38xx;
+};
+
+union cvmx_gmxx_tx_spi_thresh {
+	uint64_t u64;
+	struct cvmx_gmxx_tx_spi_thresh_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t thresh:6;
+#else
+		uint64_t thresh:6;
+		uint64_t reserved_6_63:58;
+#endif
+	} s;
+};
+
+union cvmx_gmxx_tx_xaui_ctl {
+	uint64_t u64;
+	struct cvmx_gmxx_tx_xaui_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_11_63:53;
+		uint64_t hg_pause_hgi:2;
+		uint64_t hg_en:1;
+		uint64_t reserved_7_7:1;
+		uint64_t ls_byp:1;
+		uint64_t ls:2;
+		uint64_t reserved_2_3:2;
+		uint64_t uni_en:1;
+		uint64_t dic_en:1;
+#else
+		uint64_t dic_en:1;
+		uint64_t uni_en:1;
+		uint64_t reserved_2_3:2;
+		uint64_t ls:2;
+		uint64_t ls_byp:1;
+		uint64_t reserved_7_7:1;
+		uint64_t hg_en:1;
+		uint64_t hg_pause_hgi:2;
+		uint64_t reserved_11_63:53;
+#endif
+	} s;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-gpio-defs.h b/arch/mips/include/asm/octeon/cvmx-gpio-defs.h
new file mode 100644
index 000000000..5420fa667
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-gpio-defs.h
@@ -0,0 +1,399 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2012 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_GPIO_DEFS_H__
+#define __CVMX_GPIO_DEFS_H__
+
+#define CVMX_GPIO_BIT_CFGX(offset) (CVMX_ADD_IO_SEG(0x0001070000000800ull) + ((offset) & 15) * 8)
+#define CVMX_GPIO_BOOT_ENA (CVMX_ADD_IO_SEG(0x00010700000008A8ull))
+#define CVMX_GPIO_CLK_GENX(offset) (CVMX_ADD_IO_SEG(0x00010700000008C0ull) + ((offset) & 3) * 8)
+#define CVMX_GPIO_CLK_QLMX(offset) (CVMX_ADD_IO_SEG(0x00010700000008E0ull) + ((offset) & 1) * 8)
+#define CVMX_GPIO_DBG_ENA (CVMX_ADD_IO_SEG(0x00010700000008A0ull))
+#define CVMX_GPIO_INT_CLR (CVMX_ADD_IO_SEG(0x0001070000000898ull))
+#define CVMX_GPIO_MULTI_CAST (CVMX_ADD_IO_SEG(0x00010700000008B0ull))
+#define CVMX_GPIO_PIN_ENA (CVMX_ADD_IO_SEG(0x00010700000008B8ull))
+#define CVMX_GPIO_RX_DAT (CVMX_ADD_IO_SEG(0x0001070000000880ull))
+#define CVMX_GPIO_TIM_CTL (CVMX_ADD_IO_SEG(0x00010700000008A0ull))
+#define CVMX_GPIO_TX_CLR (CVMX_ADD_IO_SEG(0x0001070000000890ull))
+#define CVMX_GPIO_TX_SET (CVMX_ADD_IO_SEG(0x0001070000000888ull))
+#define CVMX_GPIO_XBIT_CFGX(offset) (CVMX_ADD_IO_SEG(0x0001070000000900ull) + ((offset) & 31) * 8 - 8*16)
+
+union cvmx_gpio_bit_cfgx {
+	uint64_t u64;
+	struct cvmx_gpio_bit_cfgx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_21_63:42;
+		uint64_t output_sel:5;
+		uint64_t synce_sel:2;
+		uint64_t clk_gen:1;
+		uint64_t clk_sel:2;
+		uint64_t fil_sel:4;
+		uint64_t fil_cnt:4;
+		uint64_t int_type:1;
+		uint64_t int_en:1;
+		uint64_t rx_xor:1;
+		uint64_t tx_oe:1;
+#else
+		uint64_t tx_oe:1;
+		uint64_t rx_xor:1;
+		uint64_t int_en:1;
+		uint64_t int_type:1;
+		uint64_t fil_cnt:4;
+		uint64_t fil_sel:4;
+		uint64_t clk_sel:2;
+		uint64_t clk_gen:1;
+		uint64_t synce_sel:2;
+		uint64_t output_sel:5;
+		uint64_t reserved_21_63:42;
+#endif
+	} s;
+	struct cvmx_gpio_bit_cfgx_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t fil_sel:4;
+		uint64_t fil_cnt:4;
+		uint64_t int_type:1;
+		uint64_t int_en:1;
+		uint64_t rx_xor:1;
+		uint64_t tx_oe:1;
+#else
+		uint64_t tx_oe:1;
+		uint64_t rx_xor:1;
+		uint64_t int_en:1;
+		uint64_t int_type:1;
+		uint64_t fil_cnt:4;
+		uint64_t fil_sel:4;
+		uint64_t reserved_12_63:52;
+#endif
+	} cn30xx;
+	struct cvmx_gpio_bit_cfgx_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_15_63:49;
+		uint64_t clk_gen:1;
+		uint64_t clk_sel:2;
+		uint64_t fil_sel:4;
+		uint64_t fil_cnt:4;
+		uint64_t int_type:1;
+		uint64_t int_en:1;
+		uint64_t rx_xor:1;
+		uint64_t tx_oe:1;
+#else
+		uint64_t tx_oe:1;
+		uint64_t rx_xor:1;
+		uint64_t int_en:1;
+		uint64_t int_type:1;
+		uint64_t fil_cnt:4;
+		uint64_t fil_sel:4;
+		uint64_t clk_sel:2;
+		uint64_t clk_gen:1;
+		uint64_t reserved_15_63:49;
+#endif
+	} cn52xx;
+};
+
+union cvmx_gpio_boot_ena {
+	uint64_t u64;
+	struct cvmx_gpio_boot_ena_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t boot_ena:4;
+		uint64_t reserved_0_7:8;
+#else
+		uint64_t reserved_0_7:8;
+		uint64_t boot_ena:4;
+		uint64_t reserved_12_63:52;
+#endif
+	} s;
+};
+
+union cvmx_gpio_clk_genx {
+	uint64_t u64;
+	struct cvmx_gpio_clk_genx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t n:32;
+#else
+		uint64_t n:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_gpio_clk_qlmx {
+	uint64_t u64;
+	struct cvmx_gpio_clk_qlmx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_11_63:53;
+		uint64_t qlm_sel:3;
+		uint64_t reserved_3_7:5;
+		uint64_t div:1;
+		uint64_t lane_sel:2;
+#else
+		uint64_t lane_sel:2;
+		uint64_t div:1;
+		uint64_t reserved_3_7:5;
+		uint64_t qlm_sel:3;
+		uint64_t reserved_11_63:53;
+#endif
+	} s;
+	struct cvmx_gpio_clk_qlmx_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t qlm_sel:2;
+		uint64_t reserved_3_7:5;
+		uint64_t div:1;
+		uint64_t lane_sel:2;
+#else
+		uint64_t lane_sel:2;
+		uint64_t div:1;
+		uint64_t reserved_3_7:5;
+		uint64_t qlm_sel:2;
+		uint64_t reserved_10_63:54;
+#endif
+	} cn61xx;
+	struct cvmx_gpio_clk_qlmx_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_3_63:61;
+		uint64_t div:1;
+		uint64_t lane_sel:2;
+#else
+		uint64_t lane_sel:2;
+		uint64_t div:1;
+		uint64_t reserved_3_63:61;
+#endif
+	} cn63xx;
+};
+
+union cvmx_gpio_dbg_ena {
+	uint64_t u64;
+	struct cvmx_gpio_dbg_ena_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_21_63:43;
+		uint64_t dbg_ena:21;
+#else
+		uint64_t dbg_ena:21;
+		uint64_t reserved_21_63:43;
+#endif
+	} s;
+};
+
+union cvmx_gpio_int_clr {
+	uint64_t u64;
+	struct cvmx_gpio_int_clr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t type:16;
+#else
+		uint64_t type:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_gpio_multi_cast {
+	uint64_t u64;
+	struct cvmx_gpio_multi_cast_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t en:1;
+#else
+		uint64_t en:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_gpio_pin_ena {
+	uint64_t u64;
+	struct cvmx_gpio_pin_ena_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t ena19:1;
+		uint64_t ena18:1;
+		uint64_t reserved_0_17:18;
+#else
+		uint64_t reserved_0_17:18;
+		uint64_t ena18:1;
+		uint64_t ena19:1;
+		uint64_t reserved_20_63:44;
+#endif
+	} s;
+};
+
+union cvmx_gpio_rx_dat {
+	uint64_t u64;
+	struct cvmx_gpio_rx_dat_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_24_63:40;
+		uint64_t dat:24;
+#else
+		uint64_t dat:24;
+		uint64_t reserved_24_63:40;
+#endif
+	} s;
+	struct cvmx_gpio_rx_dat_cn38xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t dat:16;
+#else
+		uint64_t dat:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} cn38xx;
+	struct cvmx_gpio_rx_dat_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t dat:20;
+#else
+		uint64_t dat:20;
+		uint64_t reserved_20_63:44;
+#endif
+	} cn61xx;
+};
+
+union cvmx_gpio_tim_ctl {
+	uint64_t u64;
+	struct cvmx_gpio_tim_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t sel:4;
+#else
+		uint64_t sel:4;
+		uint64_t reserved_4_63:60;
+#endif
+	} s;
+};
+
+union cvmx_gpio_tx_clr {
+	uint64_t u64;
+	struct cvmx_gpio_tx_clr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_24_63:40;
+		uint64_t clr:24;
+#else
+		uint64_t clr:24;
+		uint64_t reserved_24_63:40;
+#endif
+	} s;
+	struct cvmx_gpio_tx_clr_cn38xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t clr:16;
+#else
+		uint64_t clr:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} cn38xx;
+	struct cvmx_gpio_tx_clr_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t clr:20;
+#else
+		uint64_t clr:20;
+		uint64_t reserved_20_63:44;
+#endif
+	} cn61xx;
+};
+
+union cvmx_gpio_tx_set {
+	uint64_t u64;
+	struct cvmx_gpio_tx_set_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_24_63:40;
+		uint64_t set:24;
+#else
+		uint64_t set:24;
+		uint64_t reserved_24_63:40;
+#endif
+	} s;
+	struct cvmx_gpio_tx_set_cn38xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t set:16;
+#else
+		uint64_t set:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} cn38xx;
+	struct cvmx_gpio_tx_set_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t set:20;
+#else
+		uint64_t set:20;
+		uint64_t reserved_20_63:44;
+#endif
+	} cn61xx;
+};
+
+union cvmx_gpio_xbit_cfgx {
+	uint64_t u64;
+	struct cvmx_gpio_xbit_cfgx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_17_63:47;
+		uint64_t synce_sel:2;
+		uint64_t clk_gen:1;
+		uint64_t clk_sel:2;
+		uint64_t fil_sel:4;
+		uint64_t fil_cnt:4;
+		uint64_t int_type:1;
+		uint64_t int_en:1;
+		uint64_t rx_xor:1;
+		uint64_t tx_oe:1;
+#else
+		uint64_t tx_oe:1;
+		uint64_t rx_xor:1;
+		uint64_t int_en:1;
+		uint64_t int_type:1;
+		uint64_t fil_cnt:4;
+		uint64_t fil_sel:4;
+		uint64_t clk_sel:2;
+		uint64_t clk_gen:1;
+		uint64_t synce_sel:2;
+		uint64_t reserved_17_63:47;
+#endif
+	} s;
+	struct cvmx_gpio_xbit_cfgx_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t fil_sel:4;
+		uint64_t fil_cnt:4;
+		uint64_t reserved_2_3:2;
+		uint64_t rx_xor:1;
+		uint64_t tx_oe:1;
+#else
+		uint64_t tx_oe:1;
+		uint64_t rx_xor:1;
+		uint64_t reserved_2_3:2;
+		uint64_t fil_cnt:4;
+		uint64_t fil_sel:4;
+		uint64_t reserved_12_63:52;
+#endif
+	} cn30xx;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-helper-board.h b/arch/mips/include/asm/octeon/cvmx-helper-board.h
new file mode 100644
index 000000000..cfe9c256a
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-helper-board.h
@@ -0,0 +1,124 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/**
+ *
+ * Helper functions to abstract board specific data about
+ * network ports from the rest of the cvmx-helper files.
+ *
+ */
+#ifndef __CVMX_HELPER_BOARD_H__
+#define __CVMX_HELPER_BOARD_H__
+
+#include <asm/octeon/cvmx-helper.h>
+
+enum cvmx_helper_board_usb_clock_types {
+	USB_CLOCK_TYPE_REF_12,
+	USB_CLOCK_TYPE_REF_24,
+	USB_CLOCK_TYPE_REF_48,
+	USB_CLOCK_TYPE_CRYSTAL_12,
+};
+
+typedef enum {
+	set_phy_link_flags_autoneg = 0x1,
+	set_phy_link_flags_flow_control_dont_touch = 0x0 << 1,
+	set_phy_link_flags_flow_control_enable = 0x1 << 1,
+	set_phy_link_flags_flow_control_disable = 0x2 << 1,
+	set_phy_link_flags_flow_control_mask = 0x3 << 1,	/* Mask for 2 bit wide flow control field */
+} cvmx_helper_board_set_phy_link_flags_types_t;
+
+/*
+ * Fake IPD port, the RGMII/MII interface may use different PHY, use
+ * this macro to return appropriate MIX address to read the PHY.
+ */
+#define CVMX_HELPER_BOARD_MGMT_IPD_PORT	    -10
+
+/**
+ * Return the MII PHY address associated with the given IPD
+ * port. A result of -1 means there isn't a MII capable PHY
+ * connected to this port. On chips supporting multiple MII
+ * busses the bus number is encoded in bits <15:8>.
+ *
+ * This function must be modified for every new Octeon board.
+ * Internally it uses switch statements based on the cvmx_sysinfo
+ * data to determine board types and revisions. It relies on the
+ * fact that every Octeon board receives a unique board type
+ * enumeration from the bootloader.
+ *
+ * @ipd_port: Octeon IPD port to get the MII address for.
+ *
+ * Returns MII PHY address and bus number or -1.
+ */
+extern int cvmx_helper_board_get_mii_address(int ipd_port);
+
+/**
+ * This function is the board specific method of determining an
+ * ethernet ports link speed. Most Octeon boards have Marvell PHYs
+ * and are handled by the fall through case. This function must be
+ * updated for boards that don't have the normal Marvell PHYs.
+ *
+ * This function must be modified for every new Octeon board.
+ * Internally it uses switch statements based on the cvmx_sysinfo
+ * data to determine board types and revisions. It relies on the
+ * fact that every Octeon board receives a unique board type
+ * enumeration from the bootloader.
+ *
+ * @ipd_port: IPD input port associated with the port we want to get link
+ *		   status for.
+ *
+ * Returns The ports link status. If the link isn't fully resolved, this must
+ *	   return zero.
+ */
+extern union cvmx_helper_link_info __cvmx_helper_board_link_get(int ipd_port);
+
+/**
+ * This function is called by cvmx_helper_interface_probe() after it
+ * determines the number of ports Octeon can support on a specific
+ * interface. This function is the per board location to override
+ * this value. It is called with the number of ports Octeon might
+ * support and should return the number of actual ports on the
+ * board.
+ *
+ * This function must be modified for every new Octeon board.
+ * Internally it uses switch statements based on the cvmx_sysinfo
+ * data to determine board types and revisions. It relies on the
+ * fact that every Octeon board receives a unique board type
+ * enumeration from the bootloader.
+ *
+ * @interface: Interface to probe
+ * @supported_ports:
+ *		    Number of ports Octeon supports.
+ *
+ * Returns Number of ports the actual board supports. Many times this will
+ *	   simple be "support_ports".
+ */
+extern int __cvmx_helper_board_interface_probe(int interface,
+					       int supported_ports);
+
+enum cvmx_helper_board_usb_clock_types __cvmx_helper_board_usb_get_clock_type(void);
+
+#endif /* __CVMX_HELPER_BOARD_H__ */
diff --git a/arch/mips/include/asm/octeon/cvmx-helper-errata.h b/arch/mips/include/asm/octeon/cvmx-helper-errata.h
new file mode 100644
index 000000000..5fc99189f
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-helper-errata.h
@@ -0,0 +1,33 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_HELPER_ERRATA_H__
+#define __CVMX_HELPER_ERRATA_H__
+
+extern void __cvmx_helper_errata_qlm_disable_2nd_order_cdr(int qlm);
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-helper-jtag.h b/arch/mips/include/asm/octeon/cvmx-helper-jtag.h
new file mode 100644
index 000000000..29f016ddb
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-helper-jtag.h
@@ -0,0 +1,43 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/**
+ * @file
+ *
+ *  Helper utilities for qlm_jtag.
+ *
+ */
+
+#ifndef __CVMX_HELPER_JTAG_H__
+#define __CVMX_HELPER_JTAG_H__
+
+extern void cvmx_helper_qlm_jtag_init(void);
+extern uint32_t cvmx_helper_qlm_jtag_shift(int qlm, int bits, uint32_t data);
+extern void cvmx_helper_qlm_jtag_shift_zeros(int qlm, int bits);
+extern void cvmx_helper_qlm_jtag_update(int qlm);
+
+#endif /* __CVMX_HELPER_JTAG_H__ */
diff --git a/arch/mips/include/asm/octeon/cvmx-helper-loop.h b/arch/mips/include/asm/octeon/cvmx-helper-loop.h
new file mode 100644
index 000000000..077f0e9d3
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-helper-loop.h
@@ -0,0 +1,60 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as published by
+ * the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or NONINFRINGEMENT.
+ * See the GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/**
+ * @file
+ *
+ * Functions for LOOP initialization, configuration,
+ * and monitoring.
+ *
+ */
+#ifndef __CVMX_HELPER_LOOP_H__
+#define __CVMX_HELPER_LOOP_H__
+
+/**
+ * Probe a LOOP interface and determine the number of ports
+ * connected to it. The LOOP interface should still be down after
+ * this call.
+ *
+ * @interface: Interface to probe
+ *
+ * Returns Number of ports on the interface. Zero to disable.
+ */
+extern int __cvmx_helper_loop_probe(int interface);
+static inline int __cvmx_helper_loop_enumerate(int interface) {return 4; }
+
+/**
+ * Bringup and enable a LOOP interface. After this call packet
+ * I/O should be fully functional. This is called with IPD
+ * enabled but PKO disabled.
+ *
+ * @interface: Interface to bring up
+ *
+ * Returns Zero on success, negative on failure
+ */
+extern int __cvmx_helper_loop_enable(int interface);
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-helper-npi.h b/arch/mips/include/asm/octeon/cvmx-helper-npi.h
new file mode 100644
index 000000000..8df4c7faf
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-helper-npi.h
@@ -0,0 +1,61 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/**
+ * @file
+ *
+ * Functions for NPI initialization, configuration,
+ * and monitoring.
+ *
+ */
+#ifndef __CVMX_HELPER_NPI_H__
+#define __CVMX_HELPER_NPI_H__
+
+/**
+ * Probe a NPI interface and determine the number of ports
+ * connected to it. The NPI interface should still be down after
+ * this call.
+ *
+ * @interface: Interface to probe
+ *
+ * Returns Number of ports on the interface. Zero to disable.
+ */
+extern int __cvmx_helper_npi_probe(int interface);
+#define __cvmx_helper_npi_enumerate __cvmx_helper_npi_probe
+
+/**
+ * Bringup and enable a NPI interface. After this call packet
+ * I/O should be fully functional. This is called with IPD
+ * enabled but PKO disabled.
+ *
+ * @interface: Interface to bring up
+ *
+ * Returns Zero on success, negative on failure
+ */
+extern int __cvmx_helper_npi_enable(int interface);
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-helper-rgmii.h b/arch/mips/include/asm/octeon/cvmx-helper-rgmii.h
new file mode 100644
index 000000000..3e79a7f89
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-helper-rgmii.h
@@ -0,0 +1,93 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/**
+ * @file
+ *
+ * Functions for RGMII/GMII/MII initialization, configuration,
+ * and monitoring.
+ *
+ */
+#ifndef __CVMX_HELPER_RGMII_H__
+#define __CVMX_HELPER_RGMII_H__
+
+/**
+ * Probe RGMII ports and determine the number present
+ *
+ * @interface: Interface to probe
+ *
+ * Returns Number of RGMII/GMII/MII ports (0-4).
+ */
+extern int __cvmx_helper_rgmii_probe(int interface);
+#define __cvmx_helper_rgmii_enumerate __cvmx_helper_rgmii_probe
+
+/**
+ * Put an RGMII interface in loopback mode. Internal packets sent
+ * out will be received back again on the same port. Externally
+ * received packets will echo back out.
+ *
+ * @port:   IPD port number to loop.
+ */
+extern void cvmx_helper_rgmii_internal_loopback(int port);
+
+/**
+ * Configure all of the ASX, GMX, and PKO registers required
+ * to get RGMII to function on the supplied interface.
+ *
+ * @interface: PKO Interface to configure (0 or 1)
+ *
+ * Returns Zero on success
+ */
+extern int __cvmx_helper_rgmii_enable(int interface);
+
+/**
+ * Return the link state of an IPD/PKO port as returned by
+ * auto negotiation. The result of this function may not match
+ * Octeon's link config if auto negotiation has changed since
+ * the last call to cvmx_helper_link_set().
+ *
+ * @ipd_port: IPD/PKO port to query
+ *
+ * Returns Link state
+ */
+extern union cvmx_helper_link_info __cvmx_helper_rgmii_link_get(int ipd_port);
+
+/**
+ * Configure an IPD/PKO port for the specified link state. This
+ * function does not influence auto negotiation at the PHY level.
+ * The passed link state must always match the link state returned
+ * by cvmx_helper_link_get().
+ *
+ * @ipd_port:  IPD/PKO port to configure
+ * @link_info: The new link state
+ *
+ * Returns Zero on success, negative on failure
+ */
+extern int __cvmx_helper_rgmii_link_set(int ipd_port,
+					union cvmx_helper_link_info link_info);
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-helper-sgmii.h b/arch/mips/include/asm/octeon/cvmx-helper-sgmii.h
new file mode 100644
index 000000000..8aac90f18
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-helper-sgmii.h
@@ -0,0 +1,87 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/**
+ * @file
+ *
+ * Functions for SGMII initialization, configuration,
+ * and monitoring.
+ *
+ */
+#ifndef __CVMX_HELPER_SGMII_H__
+#define __CVMX_HELPER_SGMII_H__
+
+/**
+ * Probe a SGMII interface and determine the number of ports
+ * connected to it. The SGMII interface should still be down after
+ * this call.
+ *
+ * @interface: Interface to probe
+ *
+ * Returns Number of ports on the interface. Zero to disable.
+ */
+extern int __cvmx_helper_sgmii_probe(int interface);
+extern int __cvmx_helper_sgmii_enumerate(int interface);
+
+/**
+ * Bringup and enable a SGMII interface. After this call packet
+ * I/O should be fully functional. This is called with IPD
+ * enabled but PKO disabled.
+ *
+ * @interface: Interface to bring up
+ *
+ * Returns Zero on success, negative on failure
+ */
+extern int __cvmx_helper_sgmii_enable(int interface);
+
+/**
+ * Return the link state of an IPD/PKO port as returned by
+ * auto negotiation. The result of this function may not match
+ * Octeon's link config if auto negotiation has changed since
+ * the last call to cvmx_helper_link_set().
+ *
+ * @ipd_port: IPD/PKO port to query
+ *
+ * Returns Link state
+ */
+extern union cvmx_helper_link_info __cvmx_helper_sgmii_link_get(int ipd_port);
+
+/**
+ * Configure an IPD/PKO port for the specified link state. This
+ * function does not influence auto negotiation at the PHY level.
+ * The passed link state must always match the link state returned
+ * by cvmx_helper_link_get().
+ *
+ * @ipd_port:  IPD/PKO port to configure
+ * @link_info: The new link state
+ *
+ * Returns Zero on success, negative on failure
+ */
+extern int __cvmx_helper_sgmii_link_set(int ipd_port,
+					union cvmx_helper_link_info link_info);
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-helper-spi.h b/arch/mips/include/asm/octeon/cvmx-helper-spi.h
new file mode 100644
index 000000000..bc8cab936
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-helper-spi.h
@@ -0,0 +1,84 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ * Functions for SPI initialization, configuration,
+ * and monitoring.
+ */
+#ifndef __CVMX_HELPER_SPI_H__
+#define __CVMX_HELPER_SPI_H__
+
+/**
+ * Probe a SPI interface and determine the number of ports
+ * connected to it. The SPI interface should still be down after
+ * this call.
+ *
+ * @interface: Interface to probe
+ *
+ * Returns Number of ports on the interface. Zero to disable.
+ */
+extern int __cvmx_helper_spi_probe(int interface);
+extern int __cvmx_helper_spi_enumerate(int interface);
+
+/**
+ * Bringup and enable a SPI interface. After this call packet I/O
+ * should be fully functional. This is called with IPD enabled but
+ * PKO disabled.
+ *
+ * @interface: Interface to bring up
+ *
+ * Returns Zero on success, negative on failure
+ */
+extern int __cvmx_helper_spi_enable(int interface);
+
+/**
+ * Return the link state of an IPD/PKO port as returned by
+ * auto negotiation. The result of this function may not match
+ * Octeon's link config if auto negotiation has changed since
+ * the last call to cvmx_helper_link_set().
+ *
+ * @ipd_port: IPD/PKO port to query
+ *
+ * Returns Link state
+ */
+extern union cvmx_helper_link_info __cvmx_helper_spi_link_get(int ipd_port);
+
+/**
+ * Configure an IPD/PKO port for the specified link state. This
+ * function does not influence auto negotiation at the PHY level.
+ * The passed link state must always match the link state returned
+ * by cvmx_helper_link_get().
+ *
+ * @ipd_port:  IPD/PKO port to configure
+ * @link_info: The new link state
+ *
+ * Returns Zero on success, negative on failure
+ */
+extern int __cvmx_helper_spi_link_set(int ipd_port,
+				      union cvmx_helper_link_info link_info);
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-helper-util.h b/arch/mips/include/asm/octeon/cvmx-helper-util.h
new file mode 100644
index 000000000..97b27a07c
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-helper-util.h
@@ -0,0 +1,192 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ *
+ * Small helper utilities.
+ *
+ */
+
+#ifndef __CVMX_HELPER_UTIL_H__
+#define __CVMX_HELPER_UTIL_H__
+
+/**
+ * Convert a interface mode into a human readable string
+ *
+ * @mode:   Mode to convert
+ *
+ * Returns String
+ */
+extern const char
+    *cvmx_helper_interface_mode_to_string(cvmx_helper_interface_mode_t mode);
+
+/**
+ * Setup Random Early Drop to automatically begin dropping packets.
+ *
+ * @pass_thresh:
+ *		 Packets will begin slowly dropping when there are less than
+ *		 this many packet buffers free in FPA 0.
+ * @drop_thresh:
+ *		 All incoming packets will be dropped when there are less
+ *		 than this many free packet buffers in FPA 0.
+ * Returns Zero on success. Negative on failure
+ */
+extern int cvmx_helper_setup_red(int pass_thresh, int drop_thresh);
+
+/**
+ * Get the version of the CVMX libraries.
+ *
+ * Returns Version string. Note this buffer is allocated statically
+ *	   and will be shared by all callers.
+ */
+extern const char *cvmx_helper_get_version(void);
+
+/**
+ * Setup the common GMX settings that determine the number of
+ * ports. These setting apply to almost all configurations of all
+ * chips.
+ *
+ * @interface: Interface to configure
+ * @num_ports: Number of ports on the interface
+ *
+ * Returns Zero on success, negative on failure
+ */
+extern int __cvmx_helper_setup_gmx(int interface, int num_ports);
+
+/**
+ * Returns the IPD/PKO port number for a port on the given
+ * interface.
+ *
+ * @interface: Interface to use
+ * @port:      Port on the interface
+ *
+ * Returns IPD/PKO port number
+ */
+extern int cvmx_helper_get_ipd_port(int interface, int port);
+
+/**
+ * Returns the IPD/PKO port number for the first port on the given
+ * interface.
+ *
+ * @interface: Interface to use
+ *
+ * Returns IPD/PKO port number
+ */
+static inline int cvmx_helper_get_first_ipd_port(int interface)
+{
+	return cvmx_helper_get_ipd_port(interface, 0);
+}
+
+/**
+ * Returns the IPD/PKO port number for the last port on the given
+ * interface.
+ *
+ * @interface: Interface to use
+ *
+ * Returns IPD/PKO port number
+ */
+static inline int cvmx_helper_get_last_ipd_port(int interface)
+{
+	extern int cvmx_helper_ports_on_interface(int interface);
+
+	return cvmx_helper_get_first_ipd_port(interface) +
+	       cvmx_helper_ports_on_interface(interface) - 1;
+}
+
+/**
+ * Free the packet buffers contained in a work queue entry.
+ * The work queue entry is not freed.
+ *
+ * @work:   Work queue entry with packet to free
+ */
+static inline void cvmx_helper_free_packet_data(struct cvmx_wqe *work)
+{
+	uint64_t number_buffers;
+	union cvmx_buf_ptr buffer_ptr;
+	union cvmx_buf_ptr next_buffer_ptr;
+	uint64_t start_of_buffer;
+
+	number_buffers = work->word2.s.bufs;
+	if (number_buffers == 0)
+		return;
+	buffer_ptr = work->packet_ptr;
+
+	/*
+	 * Since the number of buffers is not zero, we know this is
+	 * not a dynamic short packet. We need to check if it is a
+	 * packet received with IPD_CTL_STATUS[NO_WPTR]. If this is
+	 * true, we need to free all buffers except for the first
+	 * one. The caller doesn't expect their WQE pointer to be
+	 * freed
+	 */
+	start_of_buffer = ((buffer_ptr.s.addr >> 7) - buffer_ptr.s.back) << 7;
+	if (cvmx_ptr_to_phys(work) == start_of_buffer) {
+		next_buffer_ptr =
+		    *(union cvmx_buf_ptr *) cvmx_phys_to_ptr(buffer_ptr.s.addr - 8);
+		buffer_ptr = next_buffer_ptr;
+		number_buffers--;
+	}
+
+	while (number_buffers--) {
+		/*
+		 * Remember the back pointer is in cache lines, not
+		 * 64bit words
+		 */
+		start_of_buffer =
+		    ((buffer_ptr.s.addr >> 7) - buffer_ptr.s.back) << 7;
+		/*
+		 * Read pointer to next buffer before we free the
+		 * current buffer.
+		 */
+		next_buffer_ptr =
+		    *(union cvmx_buf_ptr *) cvmx_phys_to_ptr(buffer_ptr.s.addr - 8);
+		cvmx_fpa_free(cvmx_phys_to_ptr(start_of_buffer),
+			      buffer_ptr.s.pool, 0);
+		buffer_ptr = next_buffer_ptr;
+	}
+}
+
+/**
+ * Returns the interface number for an IPD/PKO port number.
+ *
+ * @ipd_port: IPD/PKO port number
+ *
+ * Returns Interface number
+ */
+extern int cvmx_helper_get_interface_num(int ipd_port);
+
+/**
+ * Returns the interface index number for an IPD/PKO port
+ * number.
+ *
+ * @ipd_port: IPD/PKO port number
+ *
+ * Returns Interface index number
+ */
+extern int cvmx_helper_get_interface_index_num(int ipd_port);
+
+#endif /* __CVMX_HELPER_H__ */
diff --git a/arch/mips/include/asm/octeon/cvmx-helper-xaui.h b/arch/mips/include/asm/octeon/cvmx-helper-xaui.h
new file mode 100644
index 000000000..c18da2eba
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-helper-xaui.h
@@ -0,0 +1,87 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/**
+ * @file
+ *
+ * Functions for XAUI initialization, configuration,
+ * and monitoring.
+ *
+ */
+#ifndef __CVMX_HELPER_XAUI_H__
+#define __CVMX_HELPER_XAUI_H__
+
+/**
+ * Probe a XAUI interface and determine the number of ports
+ * connected to it. The XAUI interface should still be down
+ * after this call.
+ *
+ * @interface: Interface to probe
+ *
+ * Returns Number of ports on the interface. Zero to disable.
+ */
+extern int __cvmx_helper_xaui_probe(int interface);
+extern int __cvmx_helper_xaui_enumerate(int interface);
+
+/**
+ * Bringup and enable a XAUI interface. After this call packet
+ * I/O should be fully functional. This is called with IPD
+ * enabled but PKO disabled.
+ *
+ * @interface: Interface to bring up
+ *
+ * Returns Zero on success, negative on failure
+ */
+extern int __cvmx_helper_xaui_enable(int interface);
+
+/**
+ * Return the link state of an IPD/PKO port as returned by
+ * auto negotiation. The result of this function may not match
+ * Octeon's link config if auto negotiation has changed since
+ * the last call to cvmx_helper_link_set().
+ *
+ * @ipd_port: IPD/PKO port to query
+ *
+ * Returns Link state
+ */
+extern union cvmx_helper_link_info __cvmx_helper_xaui_link_get(int ipd_port);
+
+/**
+ * Configure an IPD/PKO port for the specified link state. This
+ * function does not influence auto negotiation at the PHY level.
+ * The passed link state must always match the link state returned
+ * by cvmx_helper_link_get().
+ *
+ * @ipd_port:  IPD/PKO port to configure
+ * @link_info: The new link state
+ *
+ * Returns Zero on success, negative on failure
+ */
+extern int __cvmx_helper_xaui_link_set(int ipd_port,
+				       union cvmx_helper_link_info link_info);
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-helper.h b/arch/mips/include/asm/octeon/cvmx-helper.h
new file mode 100644
index 000000000..0cddce352
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-helper.h
@@ -0,0 +1,171 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ *
+ * Helper functions for common, but complicated tasks.
+ *
+ */
+
+#ifndef __CVMX_HELPER_H__
+#define __CVMX_HELPER_H__
+
+#include <asm/octeon/cvmx-config.h>
+#include <asm/octeon/cvmx-fpa.h>
+#include <asm/octeon/cvmx-wqe.h>
+
+typedef enum {
+	CVMX_HELPER_INTERFACE_MODE_DISABLED,
+	CVMX_HELPER_INTERFACE_MODE_RGMII,
+	CVMX_HELPER_INTERFACE_MODE_GMII,
+	CVMX_HELPER_INTERFACE_MODE_SPI,
+	CVMX_HELPER_INTERFACE_MODE_PCIE,
+	CVMX_HELPER_INTERFACE_MODE_XAUI,
+	CVMX_HELPER_INTERFACE_MODE_SGMII,
+	CVMX_HELPER_INTERFACE_MODE_PICMG,
+	CVMX_HELPER_INTERFACE_MODE_NPI,
+	CVMX_HELPER_INTERFACE_MODE_LOOP,
+} cvmx_helper_interface_mode_t;
+
+union cvmx_helper_link_info {
+	uint64_t u64;
+	struct {
+		uint64_t reserved_20_63:44;
+		uint64_t link_up:1;	    /**< Is the physical link up? */
+		uint64_t full_duplex:1;	    /**< 1 if the link is full duplex */
+		uint64_t speed:18;	    /**< Speed of the link in Mbps */
+	} s;
+};
+
+#include <asm/octeon/cvmx-helper-errata.h>
+#include <asm/octeon/cvmx-helper-loop.h>
+#include <asm/octeon/cvmx-helper-npi.h>
+#include <asm/octeon/cvmx-helper-rgmii.h>
+#include <asm/octeon/cvmx-helper-sgmii.h>
+#include <asm/octeon/cvmx-helper-spi.h>
+#include <asm/octeon/cvmx-helper-util.h>
+#include <asm/octeon/cvmx-helper-xaui.h>
+
+/**
+ * This function enables the IPD and also enables the packet interfaces.
+ * The packet interfaces (RGMII and SPI) must be enabled after the
+ * IPD.	 This should be called by the user program after any additional
+ * IPD configuration changes are made if CVMX_HELPER_ENABLE_IPD
+ * is not set in the executive-config.h file.
+ *
+ * Returns 0 on success
+ *	   -1 on failure
+ */
+extern int cvmx_helper_ipd_and_packet_input_enable(void);
+
+/**
+ * Initialize the PIP, IPD, and PKO hardware to support
+ * simple priority based queues for the ethernet ports. Each
+ * port is configured with a number of priority queues based
+ * on CVMX_PKO_QUEUES_PER_PORT_* where each queue is lower
+ * priority than the previous.
+ *
+ * Returns Zero on success, non-zero on failure
+ */
+extern int cvmx_helper_initialize_packet_io_global(void);
+
+/**
+ * Returns the number of ports on the given interface.
+ * The interface must be initialized before the port count
+ * can be returned.
+ *
+ * @interface: Which interface to return port count for.
+ *
+ * Returns Port count for interface
+ *	   -1 for uninitialized interface
+ */
+extern int cvmx_helper_ports_on_interface(int interface);
+
+/**
+ * Return the number of interfaces the chip has. Each interface
+ * may have multiple ports. Most chips support two interfaces,
+ * but the CNX0XX and CNX1XX are exceptions. These only support
+ * one interface.
+ *
+ * Returns Number of interfaces on chip
+ */
+extern int cvmx_helper_get_number_of_interfaces(void);
+
+/**
+ * Get the operating mode of an interface. Depending on the Octeon
+ * chip and configuration, this function returns an enumeration
+ * of the type of packet I/O supported by an interface.
+ *
+ * @interface: Interface to probe
+ *
+ * Returns Mode of the interface. Unknown or unsupported interfaces return
+ *	   DISABLED.
+ */
+extern cvmx_helper_interface_mode_t cvmx_helper_interface_get_mode(int
+								   interface);
+
+/**
+ * Return the link state of an IPD/PKO port as returned by
+ * auto negotiation. The result of this function may not match
+ * Octeon's link config if auto negotiation has changed since
+ * the last call to cvmx_helper_link_set().
+ *
+ * @ipd_port: IPD/PKO port to query
+ *
+ * Returns Link state
+ */
+extern union cvmx_helper_link_info cvmx_helper_link_get(int ipd_port);
+
+/**
+ * Configure an IPD/PKO port for the specified link state. This
+ * function does not influence auto negotiation at the PHY level.
+ * The passed link state must always match the link state returned
+ * by cvmx_helper_link_get().
+ *
+ * @ipd_port:  IPD/PKO port to configure
+ * @link_info: The new link state
+ *
+ * Returns Zero on success, negative on failure
+ */
+extern int cvmx_helper_link_set(int ipd_port,
+				union cvmx_helper_link_info link_info);
+
+/**
+ * This function probes an interface to determine the actual
+ * number of hardware ports connected to it. It doesn't setup the
+ * ports or enable them. The main goal here is to set the global
+ * interface_port_count[interface] correctly. Hardware setup of the
+ * ports will be performed later.
+ *
+ * @interface: Interface to probe
+ *
+ * Returns Zero on success, negative on failure
+ */
+extern int cvmx_helper_interface_probe(int interface);
+extern int cvmx_helper_interface_enumerate(int interface);
+
+#endif /* __CVMX_HELPER_H__ */
diff --git a/arch/mips/include/asm/octeon/cvmx-iob-defs.h b/arch/mips/include/asm/octeon/cvmx-iob-defs.h
new file mode 100644
index 000000000..989b67bba
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-iob-defs.h
@@ -0,0 +1,903 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2012 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_IOB_DEFS_H__
+#define __CVMX_IOB_DEFS_H__
+
+#define CVMX_IOB_BIST_STATUS (CVMX_ADD_IO_SEG(0x00011800F00007F8ull))
+#define CVMX_IOB_CTL_STATUS (CVMX_ADD_IO_SEG(0x00011800F0000050ull))
+#define CVMX_IOB_DWB_PRI_CNT (CVMX_ADD_IO_SEG(0x00011800F0000028ull))
+#define CVMX_IOB_FAU_TIMEOUT (CVMX_ADD_IO_SEG(0x00011800F0000000ull))
+#define CVMX_IOB_I2C_PRI_CNT (CVMX_ADD_IO_SEG(0x00011800F0000010ull))
+#define CVMX_IOB_INB_CONTROL_MATCH (CVMX_ADD_IO_SEG(0x00011800F0000078ull))
+#define CVMX_IOB_INB_CONTROL_MATCH_ENB (CVMX_ADD_IO_SEG(0x00011800F0000088ull))
+#define CVMX_IOB_INB_DATA_MATCH (CVMX_ADD_IO_SEG(0x00011800F0000070ull))
+#define CVMX_IOB_INB_DATA_MATCH_ENB (CVMX_ADD_IO_SEG(0x00011800F0000080ull))
+#define CVMX_IOB_INT_ENB (CVMX_ADD_IO_SEG(0x00011800F0000060ull))
+#define CVMX_IOB_INT_SUM (CVMX_ADD_IO_SEG(0x00011800F0000058ull))
+#define CVMX_IOB_N2C_L2C_PRI_CNT (CVMX_ADD_IO_SEG(0x00011800F0000020ull))
+#define CVMX_IOB_N2C_RSP_PRI_CNT (CVMX_ADD_IO_SEG(0x00011800F0000008ull))
+#define CVMX_IOB_OUTB_COM_PRI_CNT (CVMX_ADD_IO_SEG(0x00011800F0000040ull))
+#define CVMX_IOB_OUTB_CONTROL_MATCH (CVMX_ADD_IO_SEG(0x00011800F0000098ull))
+#define CVMX_IOB_OUTB_CONTROL_MATCH_ENB (CVMX_ADD_IO_SEG(0x00011800F00000A8ull))
+#define CVMX_IOB_OUTB_DATA_MATCH (CVMX_ADD_IO_SEG(0x00011800F0000090ull))
+#define CVMX_IOB_OUTB_DATA_MATCH_ENB (CVMX_ADD_IO_SEG(0x00011800F00000A0ull))
+#define CVMX_IOB_OUTB_FPA_PRI_CNT (CVMX_ADD_IO_SEG(0x00011800F0000048ull))
+#define CVMX_IOB_OUTB_REQ_PRI_CNT (CVMX_ADD_IO_SEG(0x00011800F0000038ull))
+#define CVMX_IOB_P2C_REQ_PRI_CNT (CVMX_ADD_IO_SEG(0x00011800F0000018ull))
+#define CVMX_IOB_PKT_ERR (CVMX_ADD_IO_SEG(0x00011800F0000068ull))
+#define CVMX_IOB_TO_CMB_CREDITS (CVMX_ADD_IO_SEG(0x00011800F00000B0ull))
+#define CVMX_IOB_TO_NCB_DID_00_CREDITS (CVMX_ADD_IO_SEG(0x00011800F0000800ull))
+#define CVMX_IOB_TO_NCB_DID_111_CREDITS (CVMX_ADD_IO_SEG(0x00011800F0000B78ull))
+#define CVMX_IOB_TO_NCB_DID_223_CREDITS (CVMX_ADD_IO_SEG(0x00011800F0000EF8ull))
+#define CVMX_IOB_TO_NCB_DID_24_CREDITS (CVMX_ADD_IO_SEG(0x00011800F00008C0ull))
+#define CVMX_IOB_TO_NCB_DID_32_CREDITS (CVMX_ADD_IO_SEG(0x00011800F0000900ull))
+#define CVMX_IOB_TO_NCB_DID_40_CREDITS (CVMX_ADD_IO_SEG(0x00011800F0000940ull))
+#define CVMX_IOB_TO_NCB_DID_55_CREDITS (CVMX_ADD_IO_SEG(0x00011800F00009B8ull))
+#define CVMX_IOB_TO_NCB_DID_64_CREDITS (CVMX_ADD_IO_SEG(0x00011800F0000A00ull))
+#define CVMX_IOB_TO_NCB_DID_79_CREDITS (CVMX_ADD_IO_SEG(0x00011800F0000A78ull))
+#define CVMX_IOB_TO_NCB_DID_96_CREDITS (CVMX_ADD_IO_SEG(0x00011800F0000B00ull))
+#define CVMX_IOB_TO_NCB_DID_98_CREDITS (CVMX_ADD_IO_SEG(0x00011800F0000B10ull))
+
+union cvmx_iob_bist_status {
+	uint64_t u64;
+	struct cvmx_iob_bist_status_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t ibd:1;
+		uint64_t icd:1;
+#else
+		uint64_t icd:1;
+		uint64_t ibd:1;
+		uint64_t reserved_2_63:62;
+#endif
+	} s;
+	struct cvmx_iob_bist_status_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_18_63:46;
+		uint64_t icnrcb:1;
+		uint64_t icr0:1;
+		uint64_t icr1:1;
+		uint64_t icnr1:1;
+		uint64_t icnr0:1;
+		uint64_t ibdr0:1;
+		uint64_t ibdr1:1;
+		uint64_t ibr0:1;
+		uint64_t ibr1:1;
+		uint64_t icnrt:1;
+		uint64_t ibrq0:1;
+		uint64_t ibrq1:1;
+		uint64_t icrn0:1;
+		uint64_t icrn1:1;
+		uint64_t icrp0:1;
+		uint64_t icrp1:1;
+		uint64_t ibd:1;
+		uint64_t icd:1;
+#else
+		uint64_t icd:1;
+		uint64_t ibd:1;
+		uint64_t icrp1:1;
+		uint64_t icrp0:1;
+		uint64_t icrn1:1;
+		uint64_t icrn0:1;
+		uint64_t ibrq1:1;
+		uint64_t ibrq0:1;
+		uint64_t icnrt:1;
+		uint64_t ibr1:1;
+		uint64_t ibr0:1;
+		uint64_t ibdr1:1;
+		uint64_t ibdr0:1;
+		uint64_t icnr0:1;
+		uint64_t icnr1:1;
+		uint64_t icr1:1;
+		uint64_t icr0:1;
+		uint64_t icnrcb:1;
+		uint64_t reserved_18_63:46;
+#endif
+	} cn30xx;
+	struct cvmx_iob_bist_status_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_23_63:41;
+		uint64_t xmdfif:1;
+		uint64_t xmcfif:1;
+		uint64_t iorfif:1;
+		uint64_t rsdfif:1;
+		uint64_t iocfif:1;
+		uint64_t icnrcb:1;
+		uint64_t icr0:1;
+		uint64_t icr1:1;
+		uint64_t icnr1:1;
+		uint64_t icnr0:1;
+		uint64_t ibdr0:1;
+		uint64_t ibdr1:1;
+		uint64_t ibr0:1;
+		uint64_t ibr1:1;
+		uint64_t icnrt:1;
+		uint64_t ibrq0:1;
+		uint64_t ibrq1:1;
+		uint64_t icrn0:1;
+		uint64_t icrn1:1;
+		uint64_t icrp0:1;
+		uint64_t icrp1:1;
+		uint64_t ibd:1;
+		uint64_t icd:1;
+#else
+		uint64_t icd:1;
+		uint64_t ibd:1;
+		uint64_t icrp1:1;
+		uint64_t icrp0:1;
+		uint64_t icrn1:1;
+		uint64_t icrn0:1;
+		uint64_t ibrq1:1;
+		uint64_t ibrq0:1;
+		uint64_t icnrt:1;
+		uint64_t ibr1:1;
+		uint64_t ibr0:1;
+		uint64_t ibdr1:1;
+		uint64_t ibdr0:1;
+		uint64_t icnr0:1;
+		uint64_t icnr1:1;
+		uint64_t icr1:1;
+		uint64_t icr0:1;
+		uint64_t icnrcb:1;
+		uint64_t iocfif:1;
+		uint64_t rsdfif:1;
+		uint64_t iorfif:1;
+		uint64_t xmcfif:1;
+		uint64_t xmdfif:1;
+		uint64_t reserved_23_63:41;
+#endif
+	} cn61xx;
+	struct cvmx_iob_bist_status_cn68xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_18_63:46;
+		uint64_t xmdfif:1;
+		uint64_t xmcfif:1;
+		uint64_t iorfif:1;
+		uint64_t rsdfif:1;
+		uint64_t iocfif:1;
+		uint64_t icnrcb:1;
+		uint64_t icr0:1;
+		uint64_t icr1:1;
+		uint64_t icnr0:1;
+		uint64_t ibr0:1;
+		uint64_t ibr1:1;
+		uint64_t icnrt:1;
+		uint64_t ibrq0:1;
+		uint64_t ibrq1:1;
+		uint64_t icrn0:1;
+		uint64_t icrn1:1;
+		uint64_t ibd:1;
+		uint64_t icd:1;
+#else
+		uint64_t icd:1;
+		uint64_t ibd:1;
+		uint64_t icrn1:1;
+		uint64_t icrn0:1;
+		uint64_t ibrq1:1;
+		uint64_t ibrq0:1;
+		uint64_t icnrt:1;
+		uint64_t ibr1:1;
+		uint64_t ibr0:1;
+		uint64_t icnr0:1;
+		uint64_t icr1:1;
+		uint64_t icr0:1;
+		uint64_t icnrcb:1;
+		uint64_t iocfif:1;
+		uint64_t rsdfif:1;
+		uint64_t iorfif:1;
+		uint64_t xmcfif:1;
+		uint64_t xmdfif:1;
+		uint64_t reserved_18_63:46;
+#endif
+	} cn68xx;
+};
+
+union cvmx_iob_ctl_status {
+	uint64_t u64;
+	struct cvmx_iob_ctl_status_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_11_63:53;
+		uint64_t fif_dly:1;
+		uint64_t xmc_per:4;
+		uint64_t reserved_5_5:1;
+		uint64_t outb_mat:1;
+		uint64_t inb_mat:1;
+		uint64_t pko_enb:1;
+		uint64_t dwb_enb:1;
+		uint64_t fau_end:1;
+#else
+		uint64_t fau_end:1;
+		uint64_t dwb_enb:1;
+		uint64_t pko_enb:1;
+		uint64_t inb_mat:1;
+		uint64_t outb_mat:1;
+		uint64_t reserved_5_5:1;
+		uint64_t xmc_per:4;
+		uint64_t fif_dly:1;
+		uint64_t reserved_11_63:53;
+#endif
+	} s;
+	struct cvmx_iob_ctl_status_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_5_63:59;
+		uint64_t outb_mat:1;
+		uint64_t inb_mat:1;
+		uint64_t pko_enb:1;
+		uint64_t dwb_enb:1;
+		uint64_t fau_end:1;
+#else
+		uint64_t fau_end:1;
+		uint64_t dwb_enb:1;
+		uint64_t pko_enb:1;
+		uint64_t inb_mat:1;
+		uint64_t outb_mat:1;
+		uint64_t reserved_5_63:59;
+#endif
+	} cn30xx;
+	struct cvmx_iob_ctl_status_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t rr_mode:1;
+		uint64_t outb_mat:1;
+		uint64_t inb_mat:1;
+		uint64_t pko_enb:1;
+		uint64_t dwb_enb:1;
+		uint64_t fau_end:1;
+#else
+		uint64_t fau_end:1;
+		uint64_t dwb_enb:1;
+		uint64_t pko_enb:1;
+		uint64_t inb_mat:1;
+		uint64_t outb_mat:1;
+		uint64_t rr_mode:1;
+		uint64_t reserved_6_63:58;
+#endif
+	} cn52xx;
+	struct cvmx_iob_ctl_status_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_11_63:53;
+		uint64_t fif_dly:1;
+		uint64_t xmc_per:4;
+		uint64_t rr_mode:1;
+		uint64_t outb_mat:1;
+		uint64_t inb_mat:1;
+		uint64_t pko_enb:1;
+		uint64_t dwb_enb:1;
+		uint64_t fau_end:1;
+#else
+		uint64_t fau_end:1;
+		uint64_t dwb_enb:1;
+		uint64_t pko_enb:1;
+		uint64_t inb_mat:1;
+		uint64_t outb_mat:1;
+		uint64_t rr_mode:1;
+		uint64_t xmc_per:4;
+		uint64_t fif_dly:1;
+		uint64_t reserved_11_63:53;
+#endif
+	} cn61xx;
+	struct cvmx_iob_ctl_status_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t xmc_per:4;
+		uint64_t rr_mode:1;
+		uint64_t outb_mat:1;
+		uint64_t inb_mat:1;
+		uint64_t pko_enb:1;
+		uint64_t dwb_enb:1;
+		uint64_t fau_end:1;
+#else
+		uint64_t fau_end:1;
+		uint64_t dwb_enb:1;
+		uint64_t pko_enb:1;
+		uint64_t inb_mat:1;
+		uint64_t outb_mat:1;
+		uint64_t rr_mode:1;
+		uint64_t xmc_per:4;
+		uint64_t reserved_10_63:54;
+#endif
+	} cn63xx;
+	struct cvmx_iob_ctl_status_cn68xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_11_63:53;
+		uint64_t fif_dly:1;
+		uint64_t xmc_per:4;
+		uint64_t rsvr5:1;
+		uint64_t outb_mat:1;
+		uint64_t inb_mat:1;
+		uint64_t pko_enb:1;
+		uint64_t dwb_enb:1;
+		uint64_t fau_end:1;
+#else
+		uint64_t fau_end:1;
+		uint64_t dwb_enb:1;
+		uint64_t pko_enb:1;
+		uint64_t inb_mat:1;
+		uint64_t outb_mat:1;
+		uint64_t rsvr5:1;
+		uint64_t xmc_per:4;
+		uint64_t fif_dly:1;
+		uint64_t reserved_11_63:53;
+#endif
+	} cn68xx;
+};
+
+union cvmx_iob_dwb_pri_cnt {
+	uint64_t u64;
+	struct cvmx_iob_dwb_pri_cnt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t cnt_enb:1;
+		uint64_t cnt_val:15;
+#else
+		uint64_t cnt_val:15;
+		uint64_t cnt_enb:1;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_iob_fau_timeout {
+	uint64_t u64;
+	struct cvmx_iob_fau_timeout_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_13_63:51;
+		uint64_t tout_enb:1;
+		uint64_t tout_val:12;
+#else
+		uint64_t tout_val:12;
+		uint64_t tout_enb:1;
+		uint64_t reserved_13_63:51;
+#endif
+	} s;
+};
+
+union cvmx_iob_i2c_pri_cnt {
+	uint64_t u64;
+	struct cvmx_iob_i2c_pri_cnt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t cnt_enb:1;
+		uint64_t cnt_val:15;
+#else
+		uint64_t cnt_val:15;
+		uint64_t cnt_enb:1;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_iob_inb_control_match {
+	uint64_t u64;
+	struct cvmx_iob_inb_control_match_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t mask:8;
+		uint64_t opc:4;
+		uint64_t dst:9;
+		uint64_t src:8;
+#else
+		uint64_t src:8;
+		uint64_t dst:9;
+		uint64_t opc:4;
+		uint64_t mask:8;
+		uint64_t reserved_29_63:35;
+#endif
+	} s;
+};
+
+union cvmx_iob_inb_control_match_enb {
+	uint64_t u64;
+	struct cvmx_iob_inb_control_match_enb_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t mask:8;
+		uint64_t opc:4;
+		uint64_t dst:9;
+		uint64_t src:8;
+#else
+		uint64_t src:8;
+		uint64_t dst:9;
+		uint64_t opc:4;
+		uint64_t mask:8;
+		uint64_t reserved_29_63:35;
+#endif
+	} s;
+};
+
+union cvmx_iob_inb_data_match {
+	uint64_t u64;
+	struct cvmx_iob_inb_data_match_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t data:64;
+#else
+		uint64_t data:64;
+#endif
+	} s;
+};
+
+union cvmx_iob_inb_data_match_enb {
+	uint64_t u64;
+	struct cvmx_iob_inb_data_match_enb_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t data:64;
+#else
+		uint64_t data:64;
+#endif
+	} s;
+};
+
+union cvmx_iob_int_enb {
+	uint64_t u64;
+	struct cvmx_iob_int_enb_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t p_dat:1;
+		uint64_t np_dat:1;
+		uint64_t p_eop:1;
+		uint64_t p_sop:1;
+		uint64_t np_eop:1;
+		uint64_t np_sop:1;
+#else
+		uint64_t np_sop:1;
+		uint64_t np_eop:1;
+		uint64_t p_sop:1;
+		uint64_t p_eop:1;
+		uint64_t np_dat:1;
+		uint64_t p_dat:1;
+		uint64_t reserved_6_63:58;
+#endif
+	} s;
+	struct cvmx_iob_int_enb_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t p_eop:1;
+		uint64_t p_sop:1;
+		uint64_t np_eop:1;
+		uint64_t np_sop:1;
+#else
+		uint64_t np_sop:1;
+		uint64_t np_eop:1;
+		uint64_t p_sop:1;
+		uint64_t p_eop:1;
+		uint64_t reserved_4_63:60;
+#endif
+	} cn30xx;
+	struct cvmx_iob_int_enb_cn68xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_0_63:64;
+#else
+		uint64_t reserved_0_63:64;
+#endif
+	} cn68xx;
+};
+
+union cvmx_iob_int_sum {
+	uint64_t u64;
+	struct cvmx_iob_int_sum_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t p_dat:1;
+		uint64_t np_dat:1;
+		uint64_t p_eop:1;
+		uint64_t p_sop:1;
+		uint64_t np_eop:1;
+		uint64_t np_sop:1;
+#else
+		uint64_t np_sop:1;
+		uint64_t np_eop:1;
+		uint64_t p_sop:1;
+		uint64_t p_eop:1;
+		uint64_t np_dat:1;
+		uint64_t p_dat:1;
+		uint64_t reserved_6_63:58;
+#endif
+	} s;
+	struct cvmx_iob_int_sum_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t p_eop:1;
+		uint64_t p_sop:1;
+		uint64_t np_eop:1;
+		uint64_t np_sop:1;
+#else
+		uint64_t np_sop:1;
+		uint64_t np_eop:1;
+		uint64_t p_sop:1;
+		uint64_t p_eop:1;
+		uint64_t reserved_4_63:60;
+#endif
+	} cn30xx;
+	struct cvmx_iob_int_sum_cn68xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_0_63:64;
+#else
+		uint64_t reserved_0_63:64;
+#endif
+	} cn68xx;
+};
+
+union cvmx_iob_n2c_l2c_pri_cnt {
+	uint64_t u64;
+	struct cvmx_iob_n2c_l2c_pri_cnt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t cnt_enb:1;
+		uint64_t cnt_val:15;
+#else
+		uint64_t cnt_val:15;
+		uint64_t cnt_enb:1;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_iob_n2c_rsp_pri_cnt {
+	uint64_t u64;
+	struct cvmx_iob_n2c_rsp_pri_cnt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t cnt_enb:1;
+		uint64_t cnt_val:15;
+#else
+		uint64_t cnt_val:15;
+		uint64_t cnt_enb:1;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_iob_outb_com_pri_cnt {
+	uint64_t u64;
+	struct cvmx_iob_outb_com_pri_cnt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t cnt_enb:1;
+		uint64_t cnt_val:15;
+#else
+		uint64_t cnt_val:15;
+		uint64_t cnt_enb:1;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_iob_outb_control_match {
+	uint64_t u64;
+	struct cvmx_iob_outb_control_match_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_26_63:38;
+		uint64_t mask:8;
+		uint64_t eot:1;
+		uint64_t dst:8;
+		uint64_t src:9;
+#else
+		uint64_t src:9;
+		uint64_t dst:8;
+		uint64_t eot:1;
+		uint64_t mask:8;
+		uint64_t reserved_26_63:38;
+#endif
+	} s;
+};
+
+union cvmx_iob_outb_control_match_enb {
+	uint64_t u64;
+	struct cvmx_iob_outb_control_match_enb_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_26_63:38;
+		uint64_t mask:8;
+		uint64_t eot:1;
+		uint64_t dst:8;
+		uint64_t src:9;
+#else
+		uint64_t src:9;
+		uint64_t dst:8;
+		uint64_t eot:1;
+		uint64_t mask:8;
+		uint64_t reserved_26_63:38;
+#endif
+	} s;
+};
+
+union cvmx_iob_outb_data_match {
+	uint64_t u64;
+	struct cvmx_iob_outb_data_match_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t data:64;
+#else
+		uint64_t data:64;
+#endif
+	} s;
+};
+
+union cvmx_iob_outb_data_match_enb {
+	uint64_t u64;
+	struct cvmx_iob_outb_data_match_enb_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t data:64;
+#else
+		uint64_t data:64;
+#endif
+	} s;
+};
+
+union cvmx_iob_outb_fpa_pri_cnt {
+	uint64_t u64;
+	struct cvmx_iob_outb_fpa_pri_cnt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t cnt_enb:1;
+		uint64_t cnt_val:15;
+#else
+		uint64_t cnt_val:15;
+		uint64_t cnt_enb:1;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_iob_outb_req_pri_cnt {
+	uint64_t u64;
+	struct cvmx_iob_outb_req_pri_cnt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t cnt_enb:1;
+		uint64_t cnt_val:15;
+#else
+		uint64_t cnt_val:15;
+		uint64_t cnt_enb:1;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_iob_p2c_req_pri_cnt {
+	uint64_t u64;
+	struct cvmx_iob_p2c_req_pri_cnt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t cnt_enb:1;
+		uint64_t cnt_val:15;
+#else
+		uint64_t cnt_val:15;
+		uint64_t cnt_enb:1;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_iob_pkt_err {
+	uint64_t u64;
+	struct cvmx_iob_pkt_err_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t vport:6;
+		uint64_t port:6;
+#else
+		uint64_t port:6;
+		uint64_t vport:6;
+		uint64_t reserved_12_63:52;
+#endif
+	} s;
+	struct cvmx_iob_pkt_err_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t port:6;
+#else
+		uint64_t port:6;
+		uint64_t reserved_6_63:58;
+#endif
+	} cn30xx;
+};
+
+union cvmx_iob_to_cmb_credits {
+	uint64_t u64;
+	struct cvmx_iob_to_cmb_credits_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t ncb_rd:3;
+		uint64_t ncb_wr:3;
+#else
+		uint64_t ncb_wr:3;
+		uint64_t ncb_rd:3;
+		uint64_t reserved_6_63:58;
+#endif
+	} s;
+	struct cvmx_iob_to_cmb_credits_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_9_63:55;
+		uint64_t pko_rd:3;
+		uint64_t ncb_rd:3;
+		uint64_t ncb_wr:3;
+#else
+		uint64_t ncb_wr:3;
+		uint64_t ncb_rd:3;
+		uint64_t pko_rd:3;
+		uint64_t reserved_9_63:55;
+#endif
+	} cn52xx;
+	struct cvmx_iob_to_cmb_credits_cn68xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_9_63:55;
+		uint64_t dwb:3;
+		uint64_t ncb_rd:3;
+		uint64_t ncb_wr:3;
+#else
+		uint64_t ncb_wr:3;
+		uint64_t ncb_rd:3;
+		uint64_t dwb:3;
+		uint64_t reserved_9_63:55;
+#endif
+	} cn68xx;
+};
+
+union cvmx_iob_to_ncb_did_00_credits {
+	uint64_t u64;
+	struct cvmx_iob_to_ncb_did_00_credits_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t crd:7;
+#else
+		uint64_t crd:7;
+		uint64_t reserved_7_63:57;
+#endif
+	} s;
+};
+
+union cvmx_iob_to_ncb_did_111_credits {
+	uint64_t u64;
+	struct cvmx_iob_to_ncb_did_111_credits_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t crd:7;
+#else
+		uint64_t crd:7;
+		uint64_t reserved_7_63:57;
+#endif
+	} s;
+};
+
+union cvmx_iob_to_ncb_did_223_credits {
+	uint64_t u64;
+	struct cvmx_iob_to_ncb_did_223_credits_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t crd:7;
+#else
+		uint64_t crd:7;
+		uint64_t reserved_7_63:57;
+#endif
+	} s;
+};
+
+union cvmx_iob_to_ncb_did_24_credits {
+	uint64_t u64;
+	struct cvmx_iob_to_ncb_did_24_credits_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t crd:7;
+#else
+		uint64_t crd:7;
+		uint64_t reserved_7_63:57;
+#endif
+	} s;
+};
+
+union cvmx_iob_to_ncb_did_32_credits {
+	uint64_t u64;
+	struct cvmx_iob_to_ncb_did_32_credits_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t crd:7;
+#else
+		uint64_t crd:7;
+		uint64_t reserved_7_63:57;
+#endif
+	} s;
+};
+
+union cvmx_iob_to_ncb_did_40_credits {
+	uint64_t u64;
+	struct cvmx_iob_to_ncb_did_40_credits_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t crd:7;
+#else
+		uint64_t crd:7;
+		uint64_t reserved_7_63:57;
+#endif
+	} s;
+};
+
+union cvmx_iob_to_ncb_did_55_credits {
+	uint64_t u64;
+	struct cvmx_iob_to_ncb_did_55_credits_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t crd:7;
+#else
+		uint64_t crd:7;
+		uint64_t reserved_7_63:57;
+#endif
+	} s;
+};
+
+union cvmx_iob_to_ncb_did_64_credits {
+	uint64_t u64;
+	struct cvmx_iob_to_ncb_did_64_credits_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t crd:7;
+#else
+		uint64_t crd:7;
+		uint64_t reserved_7_63:57;
+#endif
+	} s;
+};
+
+union cvmx_iob_to_ncb_did_79_credits {
+	uint64_t u64;
+	struct cvmx_iob_to_ncb_did_79_credits_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t crd:7;
+#else
+		uint64_t crd:7;
+		uint64_t reserved_7_63:57;
+#endif
+	} s;
+};
+
+union cvmx_iob_to_ncb_did_96_credits {
+	uint64_t u64;
+	struct cvmx_iob_to_ncb_did_96_credits_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t crd:7;
+#else
+		uint64_t crd:7;
+		uint64_t reserved_7_63:57;
+#endif
+	} s;
+};
+
+union cvmx_iob_to_ncb_did_98_credits {
+	uint64_t u64;
+	struct cvmx_iob_to_ncb_did_98_credits_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t crd:7;
+#else
+		uint64_t crd:7;
+		uint64_t reserved_7_63:57;
+#endif
+	} s;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-ipd-defs.h b/arch/mips/include/asm/octeon/cvmx-ipd-defs.h
new file mode 100644
index 000000000..c0a4ac7b4
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-ipd-defs.h
@@ -0,0 +1,1472 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2012 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_IPD_DEFS_H__
+#define __CVMX_IPD_DEFS_H__
+
+#define CVMX_IPD_1ST_MBUFF_SKIP (CVMX_ADD_IO_SEG(0x00014F0000000000ull))
+#define CVMX_IPD_1st_NEXT_PTR_BACK (CVMX_ADD_IO_SEG(0x00014F0000000150ull))
+#define CVMX_IPD_2nd_NEXT_PTR_BACK (CVMX_ADD_IO_SEG(0x00014F0000000158ull))
+#define CVMX_IPD_BIST_STATUS (CVMX_ADD_IO_SEG(0x00014F00000007F8ull))
+#define CVMX_IPD_BPIDX_MBUF_TH(offset) (CVMX_ADD_IO_SEG(0x00014F0000002000ull) + ((offset) & 63) * 8)
+#define CVMX_IPD_BPID_BP_COUNTERX(offset) (CVMX_ADD_IO_SEG(0x00014F0000003000ull) + ((offset) & 63) * 8)
+#define CVMX_IPD_BP_PRT_RED_END (CVMX_ADD_IO_SEG(0x00014F0000000328ull))
+#define CVMX_IPD_CLK_COUNT (CVMX_ADD_IO_SEG(0x00014F0000000338ull))
+#define CVMX_IPD_CREDITS (CVMX_ADD_IO_SEG(0x00014F0000004410ull))
+#define CVMX_IPD_CTL_STATUS (CVMX_ADD_IO_SEG(0x00014F0000000018ull))
+#define CVMX_IPD_ECC_CTL (CVMX_ADD_IO_SEG(0x00014F0000004408ull))
+#define CVMX_IPD_FREE_PTR_FIFO_CTL (CVMX_ADD_IO_SEG(0x00014F0000000780ull))
+#define CVMX_IPD_FREE_PTR_VALUE (CVMX_ADD_IO_SEG(0x00014F0000000788ull))
+#define CVMX_IPD_HOLD_PTR_FIFO_CTL (CVMX_ADD_IO_SEG(0x00014F0000000790ull))
+#define CVMX_IPD_INT_ENB (CVMX_ADD_IO_SEG(0x00014F0000000160ull))
+#define CVMX_IPD_INT_SUM (CVMX_ADD_IO_SEG(0x00014F0000000168ull))
+#define CVMX_IPD_NEXT_PKT_PTR (CVMX_ADD_IO_SEG(0x00014F00000007A0ull))
+#define CVMX_IPD_NEXT_WQE_PTR (CVMX_ADD_IO_SEG(0x00014F00000007A8ull))
+#define CVMX_IPD_NOT_1ST_MBUFF_SKIP (CVMX_ADD_IO_SEG(0x00014F0000000008ull))
+#define CVMX_IPD_ON_BP_DROP_PKTX(block_id) (CVMX_ADD_IO_SEG(0x00014F0000004100ull))
+#define CVMX_IPD_PACKET_MBUFF_SIZE (CVMX_ADD_IO_SEG(0x00014F0000000010ull))
+#define CVMX_IPD_PKT_ERR (CVMX_ADD_IO_SEG(0x00014F00000003F0ull))
+#define CVMX_IPD_PKT_PTR_VALID (CVMX_ADD_IO_SEG(0x00014F0000000358ull))
+#define CVMX_IPD_PORTX_BP_PAGE_CNT(offset) (CVMX_ADD_IO_SEG(0x00014F0000000028ull) + ((offset) & 63) * 8)
+#define CVMX_IPD_PORTX_BP_PAGE_CNT2(offset) (CVMX_ADD_IO_SEG(0x00014F0000000368ull) + ((offset) & 63) * 8 - 8*36)
+#define CVMX_IPD_PORTX_BP_PAGE_CNT3(offset) (CVMX_ADD_IO_SEG(0x00014F00000003D0ull) + ((offset) & 63) * 8 - 8*40)
+#define CVMX_IPD_PORT_BP_COUNTERS2_PAIRX(offset) (CVMX_ADD_IO_SEG(0x00014F0000000388ull) + ((offset) & 63) * 8 - 8*36)
+#define CVMX_IPD_PORT_BP_COUNTERS3_PAIRX(offset) (CVMX_ADD_IO_SEG(0x00014F00000003B0ull) + ((offset) & 63) * 8 - 8*40)
+#define CVMX_IPD_PORT_BP_COUNTERS4_PAIRX(offset) (CVMX_ADD_IO_SEG(0x00014F0000000410ull) + ((offset) & 63) * 8 - 8*44)
+#define CVMX_IPD_PORT_BP_COUNTERS_PAIRX(offset) (CVMX_ADD_IO_SEG(0x00014F00000001B8ull) + ((offset) & 63) * 8)
+#define CVMX_IPD_PORT_PTR_FIFO_CTL (CVMX_ADD_IO_SEG(0x00014F0000000798ull))
+#define CVMX_IPD_PORT_QOS_INTX(offset) (CVMX_ADD_IO_SEG(0x00014F0000000808ull) + ((offset) & 7) * 8)
+#define CVMX_IPD_PORT_QOS_INT_ENBX(offset) (CVMX_ADD_IO_SEG(0x00014F0000000848ull) + ((offset) & 7) * 8)
+#define CVMX_IPD_PORT_QOS_X_CNT(offset) (CVMX_ADD_IO_SEG(0x00014F0000000888ull) + ((offset) & 511) * 8)
+#define CVMX_IPD_PORT_SOPX(block_id) (CVMX_ADD_IO_SEG(0x00014F0000004400ull))
+#define CVMX_IPD_PRC_HOLD_PTR_FIFO_CTL (CVMX_ADD_IO_SEG(0x00014F0000000348ull))
+#define CVMX_IPD_PRC_PORT_PTR_FIFO_CTL (CVMX_ADD_IO_SEG(0x00014F0000000350ull))
+#define CVMX_IPD_PTR_COUNT (CVMX_ADD_IO_SEG(0x00014F0000000320ull))
+#define CVMX_IPD_PWP_PTR_FIFO_CTL (CVMX_ADD_IO_SEG(0x00014F0000000340ull))
+#define CVMX_IPD_QOS0_RED_MARKS CVMX_IPD_QOSX_RED_MARKS(0)
+#define CVMX_IPD_QOS1_RED_MARKS CVMX_IPD_QOSX_RED_MARKS(1)
+#define CVMX_IPD_QOS2_RED_MARKS CVMX_IPD_QOSX_RED_MARKS(2)
+#define CVMX_IPD_QOS3_RED_MARKS CVMX_IPD_QOSX_RED_MARKS(3)
+#define CVMX_IPD_QOS4_RED_MARKS CVMX_IPD_QOSX_RED_MARKS(4)
+#define CVMX_IPD_QOS5_RED_MARKS CVMX_IPD_QOSX_RED_MARKS(5)
+#define CVMX_IPD_QOS6_RED_MARKS CVMX_IPD_QOSX_RED_MARKS(6)
+#define CVMX_IPD_QOS7_RED_MARKS CVMX_IPD_QOSX_RED_MARKS(7)
+#define CVMX_IPD_QOSX_RED_MARKS(offset) (CVMX_ADD_IO_SEG(0x00014F0000000178ull) + ((offset) & 7) * 8)
+#define CVMX_IPD_QUE0_FREE_PAGE_CNT (CVMX_ADD_IO_SEG(0x00014F0000000330ull))
+#define CVMX_IPD_RED_BPID_ENABLEX(block_id) (CVMX_ADD_IO_SEG(0x00014F0000004200ull))
+#define CVMX_IPD_RED_DELAY (CVMX_ADD_IO_SEG(0x00014F0000004300ull))
+#define CVMX_IPD_RED_PORT_ENABLE (CVMX_ADD_IO_SEG(0x00014F00000002D8ull))
+#define CVMX_IPD_RED_PORT_ENABLE2 (CVMX_ADD_IO_SEG(0x00014F00000003A8ull))
+#define CVMX_IPD_RED_QUE0_PARAM CVMX_IPD_RED_QUEX_PARAM(0)
+#define CVMX_IPD_RED_QUE1_PARAM CVMX_IPD_RED_QUEX_PARAM(1)
+#define CVMX_IPD_RED_QUE2_PARAM CVMX_IPD_RED_QUEX_PARAM(2)
+#define CVMX_IPD_RED_QUE3_PARAM CVMX_IPD_RED_QUEX_PARAM(3)
+#define CVMX_IPD_RED_QUE4_PARAM CVMX_IPD_RED_QUEX_PARAM(4)
+#define CVMX_IPD_RED_QUE5_PARAM CVMX_IPD_RED_QUEX_PARAM(5)
+#define CVMX_IPD_RED_QUE6_PARAM CVMX_IPD_RED_QUEX_PARAM(6)
+#define CVMX_IPD_RED_QUE7_PARAM CVMX_IPD_RED_QUEX_PARAM(7)
+#define CVMX_IPD_RED_QUEX_PARAM(offset) (CVMX_ADD_IO_SEG(0x00014F00000002E0ull) + ((offset) & 7) * 8)
+#define CVMX_IPD_REQ_WGT (CVMX_ADD_IO_SEG(0x00014F0000004418ull))
+#define CVMX_IPD_SUB_PORT_BP_PAGE_CNT (CVMX_ADD_IO_SEG(0x00014F0000000148ull))
+#define CVMX_IPD_SUB_PORT_FCS (CVMX_ADD_IO_SEG(0x00014F0000000170ull))
+#define CVMX_IPD_SUB_PORT_QOS_CNT (CVMX_ADD_IO_SEG(0x00014F0000000800ull))
+#define CVMX_IPD_WQE_FPA_QUEUE (CVMX_ADD_IO_SEG(0x00014F0000000020ull))
+#define CVMX_IPD_WQE_PTR_VALID (CVMX_ADD_IO_SEG(0x00014F0000000360ull))
+
+union cvmx_ipd_1st_mbuff_skip {
+	uint64_t u64;
+	struct cvmx_ipd_1st_mbuff_skip_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t skip_sz:6;
+#else
+		uint64_t skip_sz:6;
+		uint64_t reserved_6_63:58;
+#endif
+	} s;
+};
+
+union cvmx_ipd_1st_next_ptr_back {
+	uint64_t u64;
+	struct cvmx_ipd_1st_next_ptr_back_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t back:4;
+#else
+		uint64_t back:4;
+		uint64_t reserved_4_63:60;
+#endif
+	} s;
+};
+
+union cvmx_ipd_2nd_next_ptr_back {
+	uint64_t u64;
+	struct cvmx_ipd_2nd_next_ptr_back_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t back:4;
+#else
+		uint64_t back:4;
+		uint64_t reserved_4_63:60;
+#endif
+	} s;
+};
+
+union cvmx_ipd_bist_status {
+	uint64_t u64;
+	struct cvmx_ipd_bist_status_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_23_63:41;
+		uint64_t iiwo1:1;
+		uint64_t iiwo0:1;
+		uint64_t iio1:1;
+		uint64_t iio0:1;
+		uint64_t pbm4:1;
+		uint64_t csr_mem:1;
+		uint64_t csr_ncmd:1;
+		uint64_t pwq_wqed:1;
+		uint64_t pwq_wp1:1;
+		uint64_t pwq_pow:1;
+		uint64_t ipq_pbe1:1;
+		uint64_t ipq_pbe0:1;
+		uint64_t pbm3:1;
+		uint64_t pbm2:1;
+		uint64_t pbm1:1;
+		uint64_t pbm0:1;
+		uint64_t pbm_word:1;
+		uint64_t pwq1:1;
+		uint64_t pwq0:1;
+		uint64_t prc_off:1;
+		uint64_t ipd_old:1;
+		uint64_t ipd_new:1;
+		uint64_t pwp:1;
+#else
+		uint64_t pwp:1;
+		uint64_t ipd_new:1;
+		uint64_t ipd_old:1;
+		uint64_t prc_off:1;
+		uint64_t pwq0:1;
+		uint64_t pwq1:1;
+		uint64_t pbm_word:1;
+		uint64_t pbm0:1;
+		uint64_t pbm1:1;
+		uint64_t pbm2:1;
+		uint64_t pbm3:1;
+		uint64_t ipq_pbe0:1;
+		uint64_t ipq_pbe1:1;
+		uint64_t pwq_pow:1;
+		uint64_t pwq_wp1:1;
+		uint64_t pwq_wqed:1;
+		uint64_t csr_ncmd:1;
+		uint64_t csr_mem:1;
+		uint64_t pbm4:1;
+		uint64_t iio0:1;
+		uint64_t iio1:1;
+		uint64_t iiwo0:1;
+		uint64_t iiwo1:1;
+		uint64_t reserved_23_63:41;
+#endif
+	} s;
+	struct cvmx_ipd_bist_status_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t pwq_wqed:1;
+		uint64_t pwq_wp1:1;
+		uint64_t pwq_pow:1;
+		uint64_t ipq_pbe1:1;
+		uint64_t ipq_pbe0:1;
+		uint64_t pbm3:1;
+		uint64_t pbm2:1;
+		uint64_t pbm1:1;
+		uint64_t pbm0:1;
+		uint64_t pbm_word:1;
+		uint64_t pwq1:1;
+		uint64_t pwq0:1;
+		uint64_t prc_off:1;
+		uint64_t ipd_old:1;
+		uint64_t ipd_new:1;
+		uint64_t pwp:1;
+#else
+		uint64_t pwp:1;
+		uint64_t ipd_new:1;
+		uint64_t ipd_old:1;
+		uint64_t prc_off:1;
+		uint64_t pwq0:1;
+		uint64_t pwq1:1;
+		uint64_t pbm_word:1;
+		uint64_t pbm0:1;
+		uint64_t pbm1:1;
+		uint64_t pbm2:1;
+		uint64_t pbm3:1;
+		uint64_t ipq_pbe0:1;
+		uint64_t ipq_pbe1:1;
+		uint64_t pwq_pow:1;
+		uint64_t pwq_wp1:1;
+		uint64_t pwq_wqed:1;
+		uint64_t reserved_16_63:48;
+#endif
+	} cn30xx;
+	struct cvmx_ipd_bist_status_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_18_63:46;
+		uint64_t csr_mem:1;
+		uint64_t csr_ncmd:1;
+		uint64_t pwq_wqed:1;
+		uint64_t pwq_wp1:1;
+		uint64_t pwq_pow:1;
+		uint64_t ipq_pbe1:1;
+		uint64_t ipq_pbe0:1;
+		uint64_t pbm3:1;
+		uint64_t pbm2:1;
+		uint64_t pbm1:1;
+		uint64_t pbm0:1;
+		uint64_t pbm_word:1;
+		uint64_t pwq1:1;
+		uint64_t pwq0:1;
+		uint64_t prc_off:1;
+		uint64_t ipd_old:1;
+		uint64_t ipd_new:1;
+		uint64_t pwp:1;
+#else
+		uint64_t pwp:1;
+		uint64_t ipd_new:1;
+		uint64_t ipd_old:1;
+		uint64_t prc_off:1;
+		uint64_t pwq0:1;
+		uint64_t pwq1:1;
+		uint64_t pbm_word:1;
+		uint64_t pbm0:1;
+		uint64_t pbm1:1;
+		uint64_t pbm2:1;
+		uint64_t pbm3:1;
+		uint64_t ipq_pbe0:1;
+		uint64_t ipq_pbe1:1;
+		uint64_t pwq_pow:1;
+		uint64_t pwq_wp1:1;
+		uint64_t pwq_wqed:1;
+		uint64_t csr_ncmd:1;
+		uint64_t csr_mem:1;
+		uint64_t reserved_18_63:46;
+#endif
+	} cn52xx;
+};
+
+union cvmx_ipd_bp_prt_red_end {
+	uint64_t u64;
+	struct cvmx_ipd_bp_prt_red_end_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t prt_enb:48;
+#else
+		uint64_t prt_enb:48;
+		uint64_t reserved_48_63:16;
+#endif
+	} s;
+	struct cvmx_ipd_bp_prt_red_end_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_36_63:28;
+		uint64_t prt_enb:36;
+#else
+		uint64_t prt_enb:36;
+		uint64_t reserved_36_63:28;
+#endif
+	} cn30xx;
+	struct cvmx_ipd_bp_prt_red_end_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_40_63:24;
+		uint64_t prt_enb:40;
+#else
+		uint64_t prt_enb:40;
+		uint64_t reserved_40_63:24;
+#endif
+	} cn52xx;
+	struct cvmx_ipd_bp_prt_red_end_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_44_63:20;
+		uint64_t prt_enb:44;
+#else
+		uint64_t prt_enb:44;
+		uint64_t reserved_44_63:20;
+#endif
+	} cn63xx;
+};
+
+union cvmx_ipd_bpidx_mbuf_th {
+	uint64_t u64;
+	struct cvmx_ipd_bpidx_mbuf_th_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_18_63:46;
+		uint64_t bp_enb:1;
+		uint64_t page_cnt:17;
+#else
+		uint64_t page_cnt:17;
+		uint64_t bp_enb:1;
+		uint64_t reserved_18_63:46;
+#endif
+	} s;
+};
+
+union cvmx_ipd_bpid_bp_counterx {
+	uint64_t u64;
+	struct cvmx_ipd_bpid_bp_counterx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_25_63:39;
+		uint64_t cnt_val:25;
+#else
+		uint64_t cnt_val:25;
+		uint64_t reserved_25_63:39;
+#endif
+	} s;
+};
+
+union cvmx_ipd_clk_count {
+	uint64_t u64;
+	struct cvmx_ipd_clk_count_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t clk_cnt:64;
+#else
+		uint64_t clk_cnt:64;
+#endif
+	} s;
+};
+
+union cvmx_ipd_credits {
+	uint64_t u64;
+	struct cvmx_ipd_credits_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t iob_wrc:8;
+		uint64_t iob_wr:8;
+#else
+		uint64_t iob_wr:8;
+		uint64_t iob_wrc:8;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_ipd_ctl_status {
+	uint64_t u64;
+	struct cvmx_ipd_ctl_status_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_18_63:46;
+		uint64_t use_sop:1;
+		uint64_t rst_done:1;
+		uint64_t clken:1;
+		uint64_t no_wptr:1;
+		uint64_t pq_apkt:1;
+		uint64_t pq_nabuf:1;
+		uint64_t ipd_full:1;
+		uint64_t pkt_off:1;
+		uint64_t len_m8:1;
+		uint64_t reset:1;
+		uint64_t addpkt:1;
+		uint64_t naddbuf:1;
+		uint64_t pkt_lend:1;
+		uint64_t wqe_lend:1;
+		uint64_t pbp_en:1;
+		uint64_t opc_mode:2;
+		uint64_t ipd_en:1;
+#else
+		uint64_t ipd_en:1;
+		uint64_t opc_mode:2;
+		uint64_t pbp_en:1;
+		uint64_t wqe_lend:1;
+		uint64_t pkt_lend:1;
+		uint64_t naddbuf:1;
+		uint64_t addpkt:1;
+		uint64_t reset:1;
+		uint64_t len_m8:1;
+		uint64_t pkt_off:1;
+		uint64_t ipd_full:1;
+		uint64_t pq_nabuf:1;
+		uint64_t pq_apkt:1;
+		uint64_t no_wptr:1;
+		uint64_t clken:1;
+		uint64_t rst_done:1;
+		uint64_t use_sop:1;
+		uint64_t reserved_18_63:46;
+#endif
+	} s;
+	struct cvmx_ipd_ctl_status_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t len_m8:1;
+		uint64_t reset:1;
+		uint64_t addpkt:1;
+		uint64_t naddbuf:1;
+		uint64_t pkt_lend:1;
+		uint64_t wqe_lend:1;
+		uint64_t pbp_en:1;
+		uint64_t opc_mode:2;
+		uint64_t ipd_en:1;
+#else
+		uint64_t ipd_en:1;
+		uint64_t opc_mode:2;
+		uint64_t pbp_en:1;
+		uint64_t wqe_lend:1;
+		uint64_t pkt_lend:1;
+		uint64_t naddbuf:1;
+		uint64_t addpkt:1;
+		uint64_t reset:1;
+		uint64_t len_m8:1;
+		uint64_t reserved_10_63:54;
+#endif
+	} cn30xx;
+	struct cvmx_ipd_ctl_status_cn38xxp2 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_9_63:55;
+		uint64_t reset:1;
+		uint64_t addpkt:1;
+		uint64_t naddbuf:1;
+		uint64_t pkt_lend:1;
+		uint64_t wqe_lend:1;
+		uint64_t pbp_en:1;
+		uint64_t opc_mode:2;
+		uint64_t ipd_en:1;
+#else
+		uint64_t ipd_en:1;
+		uint64_t opc_mode:2;
+		uint64_t pbp_en:1;
+		uint64_t wqe_lend:1;
+		uint64_t pkt_lend:1;
+		uint64_t naddbuf:1;
+		uint64_t addpkt:1;
+		uint64_t reset:1;
+		uint64_t reserved_9_63:55;
+#endif
+	} cn38xxp2;
+	struct cvmx_ipd_ctl_status_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_15_63:49;
+		uint64_t no_wptr:1;
+		uint64_t pq_apkt:1;
+		uint64_t pq_nabuf:1;
+		uint64_t ipd_full:1;
+		uint64_t pkt_off:1;
+		uint64_t len_m8:1;
+		uint64_t reset:1;
+		uint64_t addpkt:1;
+		uint64_t naddbuf:1;
+		uint64_t pkt_lend:1;
+		uint64_t wqe_lend:1;
+		uint64_t pbp_en:1;
+		uint64_t opc_mode:2;
+		uint64_t ipd_en:1;
+#else
+		uint64_t ipd_en:1;
+		uint64_t opc_mode:2;
+		uint64_t pbp_en:1;
+		uint64_t wqe_lend:1;
+		uint64_t pkt_lend:1;
+		uint64_t naddbuf:1;
+		uint64_t addpkt:1;
+		uint64_t reset:1;
+		uint64_t len_m8:1;
+		uint64_t pkt_off:1;
+		uint64_t ipd_full:1;
+		uint64_t pq_nabuf:1;
+		uint64_t pq_apkt:1;
+		uint64_t no_wptr:1;
+		uint64_t reserved_15_63:49;
+#endif
+	} cn50xx;
+	struct cvmx_ipd_ctl_status_cn58xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t ipd_full:1;
+		uint64_t pkt_off:1;
+		uint64_t len_m8:1;
+		uint64_t reset:1;
+		uint64_t addpkt:1;
+		uint64_t naddbuf:1;
+		uint64_t pkt_lend:1;
+		uint64_t wqe_lend:1;
+		uint64_t pbp_en:1;
+		uint64_t opc_mode:2;
+		uint64_t ipd_en:1;
+#else
+		uint64_t ipd_en:1;
+		uint64_t opc_mode:2;
+		uint64_t pbp_en:1;
+		uint64_t wqe_lend:1;
+		uint64_t pkt_lend:1;
+		uint64_t naddbuf:1;
+		uint64_t addpkt:1;
+		uint64_t reset:1;
+		uint64_t len_m8:1;
+		uint64_t pkt_off:1;
+		uint64_t ipd_full:1;
+		uint64_t reserved_12_63:52;
+#endif
+	} cn58xx;
+	struct cvmx_ipd_ctl_status_cn63xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t clken:1;
+		uint64_t no_wptr:1;
+		uint64_t pq_apkt:1;
+		uint64_t pq_nabuf:1;
+		uint64_t ipd_full:1;
+		uint64_t pkt_off:1;
+		uint64_t len_m8:1;
+		uint64_t reset:1;
+		uint64_t addpkt:1;
+		uint64_t naddbuf:1;
+		uint64_t pkt_lend:1;
+		uint64_t wqe_lend:1;
+		uint64_t pbp_en:1;
+		uint64_t opc_mode:2;
+		uint64_t ipd_en:1;
+#else
+		uint64_t ipd_en:1;
+		uint64_t opc_mode:2;
+		uint64_t pbp_en:1;
+		uint64_t wqe_lend:1;
+		uint64_t pkt_lend:1;
+		uint64_t naddbuf:1;
+		uint64_t addpkt:1;
+		uint64_t reset:1;
+		uint64_t len_m8:1;
+		uint64_t pkt_off:1;
+		uint64_t ipd_full:1;
+		uint64_t pq_nabuf:1;
+		uint64_t pq_apkt:1;
+		uint64_t no_wptr:1;
+		uint64_t clken:1;
+		uint64_t reserved_16_63:48;
+#endif
+	} cn63xxp1;
+};
+
+union cvmx_ipd_ecc_ctl {
+	uint64_t u64;
+	struct cvmx_ipd_ecc_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t pm3_syn:2;
+		uint64_t pm2_syn:2;
+		uint64_t pm1_syn:2;
+		uint64_t pm0_syn:2;
+#else
+		uint64_t pm0_syn:2;
+		uint64_t pm1_syn:2;
+		uint64_t pm2_syn:2;
+		uint64_t pm3_syn:2;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_ipd_free_ptr_fifo_ctl {
+	uint64_t u64;
+	struct cvmx_ipd_free_ptr_fifo_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t max_cnts:7;
+		uint64_t wraddr:8;
+		uint64_t praddr:8;
+		uint64_t cena:1;
+		uint64_t raddr:8;
+#else
+		uint64_t raddr:8;
+		uint64_t cena:1;
+		uint64_t praddr:8;
+		uint64_t wraddr:8;
+		uint64_t max_cnts:7;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_ipd_free_ptr_value {
+	uint64_t u64;
+	struct cvmx_ipd_free_ptr_value_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_33_63:31;
+		uint64_t ptr:33;
+#else
+		uint64_t ptr:33;
+		uint64_t reserved_33_63:31;
+#endif
+	} s;
+};
+
+union cvmx_ipd_hold_ptr_fifo_ctl {
+	uint64_t u64;
+	struct cvmx_ipd_hold_ptr_fifo_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_43_63:21;
+		uint64_t ptr:33;
+		uint64_t max_pkt:3;
+		uint64_t praddr:3;
+		uint64_t cena:1;
+		uint64_t raddr:3;
+#else
+		uint64_t raddr:3;
+		uint64_t cena:1;
+		uint64_t praddr:3;
+		uint64_t max_pkt:3;
+		uint64_t ptr:33;
+		uint64_t reserved_43_63:21;
+#endif
+	} s;
+};
+
+union cvmx_ipd_int_enb {
+	uint64_t u64;
+	struct cvmx_ipd_int_enb_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_23_63:41;
+		uint64_t pw3_dbe:1;
+		uint64_t pw3_sbe:1;
+		uint64_t pw2_dbe:1;
+		uint64_t pw2_sbe:1;
+		uint64_t pw1_dbe:1;
+		uint64_t pw1_sbe:1;
+		uint64_t pw0_dbe:1;
+		uint64_t pw0_sbe:1;
+		uint64_t dat:1;
+		uint64_t eop:1;
+		uint64_t sop:1;
+		uint64_t pq_sub:1;
+		uint64_t pq_add:1;
+		uint64_t bc_ovr:1;
+		uint64_t d_coll:1;
+		uint64_t c_coll:1;
+		uint64_t cc_ovr:1;
+		uint64_t dc_ovr:1;
+		uint64_t bp_sub:1;
+		uint64_t prc_par3:1;
+		uint64_t prc_par2:1;
+		uint64_t prc_par1:1;
+		uint64_t prc_par0:1;
+#else
+		uint64_t prc_par0:1;
+		uint64_t prc_par1:1;
+		uint64_t prc_par2:1;
+		uint64_t prc_par3:1;
+		uint64_t bp_sub:1;
+		uint64_t dc_ovr:1;
+		uint64_t cc_ovr:1;
+		uint64_t c_coll:1;
+		uint64_t d_coll:1;
+		uint64_t bc_ovr:1;
+		uint64_t pq_add:1;
+		uint64_t pq_sub:1;
+		uint64_t sop:1;
+		uint64_t eop:1;
+		uint64_t dat:1;
+		uint64_t pw0_sbe:1;
+		uint64_t pw0_dbe:1;
+		uint64_t pw1_sbe:1;
+		uint64_t pw1_dbe:1;
+		uint64_t pw2_sbe:1;
+		uint64_t pw2_dbe:1;
+		uint64_t pw3_sbe:1;
+		uint64_t pw3_dbe:1;
+		uint64_t reserved_23_63:41;
+#endif
+	} s;
+	struct cvmx_ipd_int_enb_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_5_63:59;
+		uint64_t bp_sub:1;
+		uint64_t prc_par3:1;
+		uint64_t prc_par2:1;
+		uint64_t prc_par1:1;
+		uint64_t prc_par0:1;
+#else
+		uint64_t prc_par0:1;
+		uint64_t prc_par1:1;
+		uint64_t prc_par2:1;
+		uint64_t prc_par3:1;
+		uint64_t bp_sub:1;
+		uint64_t reserved_5_63:59;
+#endif
+	} cn30xx;
+	struct cvmx_ipd_int_enb_cn38xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t bc_ovr:1;
+		uint64_t d_coll:1;
+		uint64_t c_coll:1;
+		uint64_t cc_ovr:1;
+		uint64_t dc_ovr:1;
+		uint64_t bp_sub:1;
+		uint64_t prc_par3:1;
+		uint64_t prc_par2:1;
+		uint64_t prc_par1:1;
+		uint64_t prc_par0:1;
+#else
+		uint64_t prc_par0:1;
+		uint64_t prc_par1:1;
+		uint64_t prc_par2:1;
+		uint64_t prc_par3:1;
+		uint64_t bp_sub:1;
+		uint64_t dc_ovr:1;
+		uint64_t cc_ovr:1;
+		uint64_t c_coll:1;
+		uint64_t d_coll:1;
+		uint64_t bc_ovr:1;
+		uint64_t reserved_10_63:54;
+#endif
+	} cn38xx;
+	struct cvmx_ipd_int_enb_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t pq_sub:1;
+		uint64_t pq_add:1;
+		uint64_t bc_ovr:1;
+		uint64_t d_coll:1;
+		uint64_t c_coll:1;
+		uint64_t cc_ovr:1;
+		uint64_t dc_ovr:1;
+		uint64_t bp_sub:1;
+		uint64_t prc_par3:1;
+		uint64_t prc_par2:1;
+		uint64_t prc_par1:1;
+		uint64_t prc_par0:1;
+#else
+		uint64_t prc_par0:1;
+		uint64_t prc_par1:1;
+		uint64_t prc_par2:1;
+		uint64_t prc_par3:1;
+		uint64_t bp_sub:1;
+		uint64_t dc_ovr:1;
+		uint64_t cc_ovr:1;
+		uint64_t c_coll:1;
+		uint64_t d_coll:1;
+		uint64_t bc_ovr:1;
+		uint64_t pq_add:1;
+		uint64_t pq_sub:1;
+		uint64_t reserved_12_63:52;
+#endif
+	} cn52xx;
+};
+
+union cvmx_ipd_int_sum {
+	uint64_t u64;
+	struct cvmx_ipd_int_sum_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_23_63:41;
+		uint64_t pw3_dbe:1;
+		uint64_t pw3_sbe:1;
+		uint64_t pw2_dbe:1;
+		uint64_t pw2_sbe:1;
+		uint64_t pw1_dbe:1;
+		uint64_t pw1_sbe:1;
+		uint64_t pw0_dbe:1;
+		uint64_t pw0_sbe:1;
+		uint64_t dat:1;
+		uint64_t eop:1;
+		uint64_t sop:1;
+		uint64_t pq_sub:1;
+		uint64_t pq_add:1;
+		uint64_t bc_ovr:1;
+		uint64_t d_coll:1;
+		uint64_t c_coll:1;
+		uint64_t cc_ovr:1;
+		uint64_t dc_ovr:1;
+		uint64_t bp_sub:1;
+		uint64_t prc_par3:1;
+		uint64_t prc_par2:1;
+		uint64_t prc_par1:1;
+		uint64_t prc_par0:1;
+#else
+		uint64_t prc_par0:1;
+		uint64_t prc_par1:1;
+		uint64_t prc_par2:1;
+		uint64_t prc_par3:1;
+		uint64_t bp_sub:1;
+		uint64_t dc_ovr:1;
+		uint64_t cc_ovr:1;
+		uint64_t c_coll:1;
+		uint64_t d_coll:1;
+		uint64_t bc_ovr:1;
+		uint64_t pq_add:1;
+		uint64_t pq_sub:1;
+		uint64_t sop:1;
+		uint64_t eop:1;
+		uint64_t dat:1;
+		uint64_t pw0_sbe:1;
+		uint64_t pw0_dbe:1;
+		uint64_t pw1_sbe:1;
+		uint64_t pw1_dbe:1;
+		uint64_t pw2_sbe:1;
+		uint64_t pw2_dbe:1;
+		uint64_t pw3_sbe:1;
+		uint64_t pw3_dbe:1;
+		uint64_t reserved_23_63:41;
+#endif
+	} s;
+	struct cvmx_ipd_int_sum_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_5_63:59;
+		uint64_t bp_sub:1;
+		uint64_t prc_par3:1;
+		uint64_t prc_par2:1;
+		uint64_t prc_par1:1;
+		uint64_t prc_par0:1;
+#else
+		uint64_t prc_par0:1;
+		uint64_t prc_par1:1;
+		uint64_t prc_par2:1;
+		uint64_t prc_par3:1;
+		uint64_t bp_sub:1;
+		uint64_t reserved_5_63:59;
+#endif
+	} cn30xx;
+	struct cvmx_ipd_int_sum_cn38xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t bc_ovr:1;
+		uint64_t d_coll:1;
+		uint64_t c_coll:1;
+		uint64_t cc_ovr:1;
+		uint64_t dc_ovr:1;
+		uint64_t bp_sub:1;
+		uint64_t prc_par3:1;
+		uint64_t prc_par2:1;
+		uint64_t prc_par1:1;
+		uint64_t prc_par0:1;
+#else
+		uint64_t prc_par0:1;
+		uint64_t prc_par1:1;
+		uint64_t prc_par2:1;
+		uint64_t prc_par3:1;
+		uint64_t bp_sub:1;
+		uint64_t dc_ovr:1;
+		uint64_t cc_ovr:1;
+		uint64_t c_coll:1;
+		uint64_t d_coll:1;
+		uint64_t bc_ovr:1;
+		uint64_t reserved_10_63:54;
+#endif
+	} cn38xx;
+	struct cvmx_ipd_int_sum_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t pq_sub:1;
+		uint64_t pq_add:1;
+		uint64_t bc_ovr:1;
+		uint64_t d_coll:1;
+		uint64_t c_coll:1;
+		uint64_t cc_ovr:1;
+		uint64_t dc_ovr:1;
+		uint64_t bp_sub:1;
+		uint64_t prc_par3:1;
+		uint64_t prc_par2:1;
+		uint64_t prc_par1:1;
+		uint64_t prc_par0:1;
+#else
+		uint64_t prc_par0:1;
+		uint64_t prc_par1:1;
+		uint64_t prc_par2:1;
+		uint64_t prc_par3:1;
+		uint64_t bp_sub:1;
+		uint64_t dc_ovr:1;
+		uint64_t cc_ovr:1;
+		uint64_t c_coll:1;
+		uint64_t d_coll:1;
+		uint64_t bc_ovr:1;
+		uint64_t pq_add:1;
+		uint64_t pq_sub:1;
+		uint64_t reserved_12_63:52;
+#endif
+	} cn52xx;
+};
+
+union cvmx_ipd_next_pkt_ptr {
+	uint64_t u64;
+	struct cvmx_ipd_next_pkt_ptr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_33_63:31;
+		uint64_t ptr:33;
+#else
+		uint64_t ptr:33;
+		uint64_t reserved_33_63:31;
+#endif
+	} s;
+};
+
+union cvmx_ipd_next_wqe_ptr {
+	uint64_t u64;
+	struct cvmx_ipd_next_wqe_ptr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_33_63:31;
+		uint64_t ptr:33;
+#else
+		uint64_t ptr:33;
+		uint64_t reserved_33_63:31;
+#endif
+	} s;
+};
+
+union cvmx_ipd_not_1st_mbuff_skip {
+	uint64_t u64;
+	struct cvmx_ipd_not_1st_mbuff_skip_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t skip_sz:6;
+#else
+		uint64_t skip_sz:6;
+		uint64_t reserved_6_63:58;
+#endif
+	} s;
+};
+
+union cvmx_ipd_on_bp_drop_pktx {
+	uint64_t u64;
+	struct cvmx_ipd_on_bp_drop_pktx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t prt_enb:64;
+#else
+		uint64_t prt_enb:64;
+#endif
+	} s;
+};
+
+union cvmx_ipd_packet_mbuff_size {
+	uint64_t u64;
+	struct cvmx_ipd_packet_mbuff_size_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t mb_size:12;
+#else
+		uint64_t mb_size:12;
+		uint64_t reserved_12_63:52;
+#endif
+	} s;
+};
+
+union cvmx_ipd_pkt_err {
+	uint64_t u64;
+	struct cvmx_ipd_pkt_err_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t reasm:6;
+#else
+		uint64_t reasm:6;
+		uint64_t reserved_6_63:58;
+#endif
+	} s;
+};
+
+union cvmx_ipd_pkt_ptr_valid {
+	uint64_t u64;
+	struct cvmx_ipd_pkt_ptr_valid_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t ptr:29;
+#else
+		uint64_t ptr:29;
+		uint64_t reserved_29_63:35;
+#endif
+	} s;
+};
+
+union cvmx_ipd_portx_bp_page_cnt {
+	uint64_t u64;
+	struct cvmx_ipd_portx_bp_page_cnt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_18_63:46;
+		uint64_t bp_enb:1;
+		uint64_t page_cnt:17;
+#else
+		uint64_t page_cnt:17;
+		uint64_t bp_enb:1;
+		uint64_t reserved_18_63:46;
+#endif
+	} s;
+};
+
+union cvmx_ipd_portx_bp_page_cnt2 {
+	uint64_t u64;
+	struct cvmx_ipd_portx_bp_page_cnt2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_18_63:46;
+		uint64_t bp_enb:1;
+		uint64_t page_cnt:17;
+#else
+		uint64_t page_cnt:17;
+		uint64_t bp_enb:1;
+		uint64_t reserved_18_63:46;
+#endif
+	} s;
+};
+
+union cvmx_ipd_portx_bp_page_cnt3 {
+	uint64_t u64;
+	struct cvmx_ipd_portx_bp_page_cnt3_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_18_63:46;
+		uint64_t bp_enb:1;
+		uint64_t page_cnt:17;
+#else
+		uint64_t page_cnt:17;
+		uint64_t bp_enb:1;
+		uint64_t reserved_18_63:46;
+#endif
+	} s;
+};
+
+union cvmx_ipd_port_bp_counters2_pairx {
+	uint64_t u64;
+	struct cvmx_ipd_port_bp_counters2_pairx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_25_63:39;
+		uint64_t cnt_val:25;
+#else
+		uint64_t cnt_val:25;
+		uint64_t reserved_25_63:39;
+#endif
+	} s;
+};
+
+union cvmx_ipd_port_bp_counters3_pairx {
+	uint64_t u64;
+	struct cvmx_ipd_port_bp_counters3_pairx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_25_63:39;
+		uint64_t cnt_val:25;
+#else
+		uint64_t cnt_val:25;
+		uint64_t reserved_25_63:39;
+#endif
+	} s;
+};
+
+union cvmx_ipd_port_bp_counters4_pairx {
+	uint64_t u64;
+	struct cvmx_ipd_port_bp_counters4_pairx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_25_63:39;
+		uint64_t cnt_val:25;
+#else
+		uint64_t cnt_val:25;
+		uint64_t reserved_25_63:39;
+#endif
+	} s;
+};
+
+union cvmx_ipd_port_bp_counters_pairx {
+	uint64_t u64;
+	struct cvmx_ipd_port_bp_counters_pairx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_25_63:39;
+		uint64_t cnt_val:25;
+#else
+		uint64_t cnt_val:25;
+		uint64_t reserved_25_63:39;
+#endif
+	} s;
+};
+
+union cvmx_ipd_port_ptr_fifo_ctl {
+	uint64_t u64;
+	struct cvmx_ipd_port_ptr_fifo_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t ptr:33;
+		uint64_t max_pkt:7;
+		uint64_t cena:1;
+		uint64_t raddr:7;
+#else
+		uint64_t raddr:7;
+		uint64_t cena:1;
+		uint64_t max_pkt:7;
+		uint64_t ptr:33;
+		uint64_t reserved_48_63:16;
+#endif
+	} s;
+};
+
+union cvmx_ipd_port_qos_x_cnt {
+	uint64_t u64;
+	struct cvmx_ipd_port_qos_x_cnt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t wmark:32;
+		uint64_t cnt:32;
+#else
+		uint64_t cnt:32;
+		uint64_t wmark:32;
+#endif
+	} s;
+};
+
+union cvmx_ipd_port_qos_intx {
+	uint64_t u64;
+	struct cvmx_ipd_port_qos_intx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t intr:64;
+#else
+		uint64_t intr:64;
+#endif
+	} s;
+};
+
+union cvmx_ipd_port_qos_int_enbx {
+	uint64_t u64;
+	struct cvmx_ipd_port_qos_int_enbx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t enb:64;
+#else
+		uint64_t enb:64;
+#endif
+	} s;
+};
+
+union cvmx_ipd_port_sopx {
+	uint64_t u64;
+	struct cvmx_ipd_port_sopx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t sop:64;
+#else
+		uint64_t sop:64;
+#endif
+	} s;
+};
+
+union cvmx_ipd_prc_hold_ptr_fifo_ctl {
+	uint64_t u64;
+	struct cvmx_ipd_prc_hold_ptr_fifo_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_39_63:25;
+		uint64_t max_pkt:3;
+		uint64_t praddr:3;
+		uint64_t ptr:29;
+		uint64_t cena:1;
+		uint64_t raddr:3;
+#else
+		uint64_t raddr:3;
+		uint64_t cena:1;
+		uint64_t ptr:29;
+		uint64_t praddr:3;
+		uint64_t max_pkt:3;
+		uint64_t reserved_39_63:25;
+#endif
+	} s;
+};
+
+union cvmx_ipd_prc_port_ptr_fifo_ctl {
+	uint64_t u64;
+	struct cvmx_ipd_prc_port_ptr_fifo_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_44_63:20;
+		uint64_t max_pkt:7;
+		uint64_t ptr:29;
+		uint64_t cena:1;
+		uint64_t raddr:7;
+#else
+		uint64_t raddr:7;
+		uint64_t cena:1;
+		uint64_t ptr:29;
+		uint64_t max_pkt:7;
+		uint64_t reserved_44_63:20;
+#endif
+	} s;
+};
+
+union cvmx_ipd_ptr_count {
+	uint64_t u64;
+	struct cvmx_ipd_ptr_count_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_19_63:45;
+		uint64_t pktv_cnt:1;
+		uint64_t wqev_cnt:1;
+		uint64_t pfif_cnt:3;
+		uint64_t pkt_pcnt:7;
+		uint64_t wqe_pcnt:7;
+#else
+		uint64_t wqe_pcnt:7;
+		uint64_t pkt_pcnt:7;
+		uint64_t pfif_cnt:3;
+		uint64_t wqev_cnt:1;
+		uint64_t pktv_cnt:1;
+		uint64_t reserved_19_63:45;
+#endif
+	} s;
+};
+
+union cvmx_ipd_pwp_ptr_fifo_ctl {
+	uint64_t u64;
+	struct cvmx_ipd_pwp_ptr_fifo_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_61_63:3;
+		uint64_t max_cnts:7;
+		uint64_t wraddr:8;
+		uint64_t praddr:8;
+		uint64_t ptr:29;
+		uint64_t cena:1;
+		uint64_t raddr:8;
+#else
+		uint64_t raddr:8;
+		uint64_t cena:1;
+		uint64_t ptr:29;
+		uint64_t praddr:8;
+		uint64_t wraddr:8;
+		uint64_t max_cnts:7;
+		uint64_t reserved_61_63:3;
+#endif
+	} s;
+};
+
+union cvmx_ipd_qosx_red_marks {
+	uint64_t u64;
+	struct cvmx_ipd_qosx_red_marks_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t drop:32;
+		uint64_t pass:32;
+#else
+		uint64_t pass:32;
+		uint64_t drop:32;
+#endif
+	} s;
+};
+
+union cvmx_ipd_que0_free_page_cnt {
+	uint64_t u64;
+	struct cvmx_ipd_que0_free_page_cnt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t q0_pcnt:32;
+#else
+		uint64_t q0_pcnt:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_ipd_red_bpid_enablex {
+	uint64_t u64;
+	struct cvmx_ipd_red_bpid_enablex_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t prt_enb:64;
+#else
+		uint64_t prt_enb:64;
+#endif
+	} s;
+};
+
+union cvmx_ipd_red_delay {
+	uint64_t u64;
+	struct cvmx_ipd_red_delay_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_28_63:36;
+		uint64_t prb_dly:14;
+		uint64_t avg_dly:14;
+#else
+		uint64_t avg_dly:14;
+		uint64_t prb_dly:14;
+		uint64_t reserved_28_63:36;
+#endif
+	} s;
+};
+
+union cvmx_ipd_red_port_enable {
+	uint64_t u64;
+	struct cvmx_ipd_red_port_enable_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t prb_dly:14;
+		uint64_t avg_dly:14;
+		uint64_t prt_enb:36;
+#else
+		uint64_t prt_enb:36;
+		uint64_t avg_dly:14;
+		uint64_t prb_dly:14;
+#endif
+	} s;
+};
+
+union cvmx_ipd_red_port_enable2 {
+	uint64_t u64;
+	struct cvmx_ipd_red_port_enable2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t prt_enb:12;
+#else
+		uint64_t prt_enb:12;
+		uint64_t reserved_12_63:52;
+#endif
+	} s;
+	struct cvmx_ipd_red_port_enable2_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t prt_enb:4;
+#else
+		uint64_t prt_enb:4;
+		uint64_t reserved_4_63:60;
+#endif
+	} cn52xx;
+	struct cvmx_ipd_red_port_enable2_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t prt_enb:8;
+#else
+		uint64_t prt_enb:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} cn63xx;
+};
+
+union cvmx_ipd_red_quex_param {
+	uint64_t u64;
+	struct cvmx_ipd_red_quex_param_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_49_63:15;
+		uint64_t use_pcnt:1;
+		uint64_t new_con:8;
+		uint64_t avg_con:8;
+		uint64_t prb_con:32;
+#else
+		uint64_t prb_con:32;
+		uint64_t avg_con:8;
+		uint64_t new_con:8;
+		uint64_t use_pcnt:1;
+		uint64_t reserved_49_63:15;
+#endif
+	} s;
+};
+
+union cvmx_ipd_req_wgt {
+	uint64_t u64;
+	struct cvmx_ipd_req_wgt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t wgt7:8;
+		uint64_t wgt6:8;
+		uint64_t wgt5:8;
+		uint64_t wgt4:8;
+		uint64_t wgt3:8;
+		uint64_t wgt2:8;
+		uint64_t wgt1:8;
+		uint64_t wgt0:8;
+#else
+		uint64_t wgt0:8;
+		uint64_t wgt1:8;
+		uint64_t wgt2:8;
+		uint64_t wgt3:8;
+		uint64_t wgt4:8;
+		uint64_t wgt5:8;
+		uint64_t wgt6:8;
+		uint64_t wgt7:8;
+#endif
+	} s;
+};
+
+union cvmx_ipd_sub_port_bp_page_cnt {
+	uint64_t u64;
+	struct cvmx_ipd_sub_port_bp_page_cnt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_31_63:33;
+		uint64_t port:6;
+		uint64_t page_cnt:25;
+#else
+		uint64_t page_cnt:25;
+		uint64_t port:6;
+		uint64_t reserved_31_63:33;
+#endif
+	} s;
+};
+
+union cvmx_ipd_sub_port_fcs {
+	uint64_t u64;
+	struct cvmx_ipd_sub_port_fcs_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_40_63:24;
+		uint64_t port_bit2:4;
+		uint64_t reserved_32_35:4;
+		uint64_t port_bit:32;
+#else
+		uint64_t port_bit:32;
+		uint64_t reserved_32_35:4;
+		uint64_t port_bit2:4;
+		uint64_t reserved_40_63:24;
+#endif
+	} s;
+	struct cvmx_ipd_sub_port_fcs_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_3_63:61;
+		uint64_t port_bit:3;
+#else
+		uint64_t port_bit:3;
+		uint64_t reserved_3_63:61;
+#endif
+	} cn30xx;
+	struct cvmx_ipd_sub_port_fcs_cn38xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t port_bit:32;
+#else
+		uint64_t port_bit:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} cn38xx;
+};
+
+union cvmx_ipd_sub_port_qos_cnt {
+	uint64_t u64;
+	struct cvmx_ipd_sub_port_qos_cnt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_41_63:23;
+		uint64_t port_qos:9;
+		uint64_t cnt:32;
+#else
+		uint64_t cnt:32;
+		uint64_t port_qos:9;
+		uint64_t reserved_41_63:23;
+#endif
+	} s;
+};
+
+union cvmx_ipd_wqe_fpa_queue {
+	uint64_t u64;
+	struct cvmx_ipd_wqe_fpa_queue_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_3_63:61;
+		uint64_t wqe_pool:3;
+#else
+		uint64_t wqe_pool:3;
+		uint64_t reserved_3_63:61;
+#endif
+	} s;
+};
+
+union cvmx_ipd_wqe_ptr_valid {
+	uint64_t u64;
+	struct cvmx_ipd_wqe_ptr_valid_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t ptr:29;
+#else
+		uint64_t ptr:29;
+		uint64_t reserved_29_63:35;
+#endif
+	} s;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-ipd.h b/arch/mips/include/asm/octeon/cvmx-ipd.h
new file mode 100644
index 000000000..adab7b54c
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-ipd.h
@@ -0,0 +1,339 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/**
+ *
+ * Interface to the hardware Input Packet Data unit.
+ */
+
+#ifndef __CVMX_IPD_H__
+#define __CVMX_IPD_H__
+
+#include <asm/octeon/octeon-feature.h>
+
+#include <asm/octeon/cvmx-ipd-defs.h>
+#include <asm/octeon/cvmx-pip-defs.h>
+
+enum cvmx_ipd_mode {
+   CVMX_IPD_OPC_MODE_STT = 0LL,	  /* All blocks DRAM, not cached in L2 */
+   CVMX_IPD_OPC_MODE_STF = 1LL,	  /* All blocks into  L2 */
+   CVMX_IPD_OPC_MODE_STF1_STT = 2LL,   /* 1st block L2, rest DRAM */
+   CVMX_IPD_OPC_MODE_STF2_STT = 3LL    /* 1st, 2nd blocks L2, rest DRAM */
+};
+
+#ifndef CVMX_ENABLE_LEN_M8_FIX
+#define CVMX_ENABLE_LEN_M8_FIX 0
+#endif
+
+/* CSR typedefs have been moved to cvmx-csr-*.h */
+typedef union cvmx_ipd_1st_mbuff_skip cvmx_ipd_mbuff_first_skip_t;
+typedef union cvmx_ipd_1st_next_ptr_back cvmx_ipd_first_next_ptr_back_t;
+
+typedef cvmx_ipd_mbuff_first_skip_t cvmx_ipd_mbuff_not_first_skip_t;
+typedef cvmx_ipd_first_next_ptr_back_t cvmx_ipd_second_next_ptr_back_t;
+
+/**
+ * Configure IPD
+ *
+ * @mbuff_size: Packets buffer size in 8 byte words
+ * @first_mbuff_skip:
+ *		     Number of 8 byte words to skip in the first buffer
+ * @not_first_mbuff_skip:
+ *		     Number of 8 byte words to skip in each following buffer
+ * @first_back: Must be same as first_mbuff_skip / 128
+ * @second_back:
+ *		     Must be same as not_first_mbuff_skip / 128
+ * @wqe_fpa_pool:
+ *		     FPA pool to get work entries from
+ * @cache_mode:
+ * @back_pres_enable_flag:
+ *		     Enable or disable port back pressure
+ */
+static inline void cvmx_ipd_config(uint64_t mbuff_size,
+				   uint64_t first_mbuff_skip,
+				   uint64_t not_first_mbuff_skip,
+				   uint64_t first_back,
+				   uint64_t second_back,
+				   uint64_t wqe_fpa_pool,
+				   enum cvmx_ipd_mode cache_mode,
+				   uint64_t back_pres_enable_flag)
+{
+	cvmx_ipd_mbuff_first_skip_t first_skip;
+	cvmx_ipd_mbuff_not_first_skip_t not_first_skip;
+	union cvmx_ipd_packet_mbuff_size size;
+	cvmx_ipd_first_next_ptr_back_t first_back_struct;
+	cvmx_ipd_second_next_ptr_back_t second_back_struct;
+	union cvmx_ipd_wqe_fpa_queue wqe_pool;
+	union cvmx_ipd_ctl_status ipd_ctl_reg;
+
+	first_skip.u64 = 0;
+	first_skip.s.skip_sz = first_mbuff_skip;
+	cvmx_write_csr(CVMX_IPD_1ST_MBUFF_SKIP, first_skip.u64);
+
+	not_first_skip.u64 = 0;
+	not_first_skip.s.skip_sz = not_first_mbuff_skip;
+	cvmx_write_csr(CVMX_IPD_NOT_1ST_MBUFF_SKIP, not_first_skip.u64);
+
+	size.u64 = 0;
+	size.s.mb_size = mbuff_size;
+	cvmx_write_csr(CVMX_IPD_PACKET_MBUFF_SIZE, size.u64);
+
+	first_back_struct.u64 = 0;
+	first_back_struct.s.back = first_back;
+	cvmx_write_csr(CVMX_IPD_1st_NEXT_PTR_BACK, first_back_struct.u64);
+
+	second_back_struct.u64 = 0;
+	second_back_struct.s.back = second_back;
+	cvmx_write_csr(CVMX_IPD_2nd_NEXT_PTR_BACK, second_back_struct.u64);
+
+	wqe_pool.u64 = 0;
+	wqe_pool.s.wqe_pool = wqe_fpa_pool;
+	cvmx_write_csr(CVMX_IPD_WQE_FPA_QUEUE, wqe_pool.u64);
+
+	ipd_ctl_reg.u64 = cvmx_read_csr(CVMX_IPD_CTL_STATUS);
+	ipd_ctl_reg.s.opc_mode = cache_mode;
+	ipd_ctl_reg.s.pbp_en = back_pres_enable_flag;
+	cvmx_write_csr(CVMX_IPD_CTL_STATUS, ipd_ctl_reg.u64);
+
+	/* Note: the example RED code that used to be here has been moved to
+	   cvmx_helper_setup_red */
+}
+
+/**
+ * Enable IPD
+ */
+static inline void cvmx_ipd_enable(void)
+{
+	union cvmx_ipd_ctl_status ipd_reg;
+	ipd_reg.u64 = cvmx_read_csr(CVMX_IPD_CTL_STATUS);
+	if (ipd_reg.s.ipd_en) {
+		cvmx_dprintf
+		    ("Warning: Enabling IPD when IPD already enabled.\n");
+	}
+	ipd_reg.s.ipd_en = 1;
+#if  CVMX_ENABLE_LEN_M8_FIX
+	if (!OCTEON_IS_MODEL(OCTEON_CN38XX_PASS2))
+		ipd_reg.s.len_m8 = TRUE;
+#endif
+	cvmx_write_csr(CVMX_IPD_CTL_STATUS, ipd_reg.u64);
+}
+
+/**
+ * Disable IPD
+ */
+static inline void cvmx_ipd_disable(void)
+{
+	union cvmx_ipd_ctl_status ipd_reg;
+	ipd_reg.u64 = cvmx_read_csr(CVMX_IPD_CTL_STATUS);
+	ipd_reg.s.ipd_en = 0;
+	cvmx_write_csr(CVMX_IPD_CTL_STATUS, ipd_reg.u64);
+}
+
+/**
+ * Supportive function for cvmx_fpa_shutdown_pool.
+ */
+static inline void cvmx_ipd_free_ptr(void)
+{
+	/* Only CN38XXp{1,2} cannot read pointer out of the IPD */
+	if (!OCTEON_IS_MODEL(OCTEON_CN38XX_PASS1)
+	    && !OCTEON_IS_MODEL(OCTEON_CN38XX_PASS2)) {
+		int no_wptr = 0;
+		union cvmx_ipd_ptr_count ipd_ptr_count;
+		ipd_ptr_count.u64 = cvmx_read_csr(CVMX_IPD_PTR_COUNT);
+
+		/* Handle Work Queue Entry in cn56xx and cn52xx */
+		if (octeon_has_feature(OCTEON_FEATURE_NO_WPTR)) {
+			union cvmx_ipd_ctl_status ipd_ctl_status;
+			ipd_ctl_status.u64 = cvmx_read_csr(CVMX_IPD_CTL_STATUS);
+			if (ipd_ctl_status.s.no_wptr)
+				no_wptr = 1;
+		}
+
+		/* Free the prefetched WQE */
+		if (ipd_ptr_count.s.wqev_cnt) {
+			union cvmx_ipd_wqe_ptr_valid ipd_wqe_ptr_valid;
+			ipd_wqe_ptr_valid.u64 =
+			    cvmx_read_csr(CVMX_IPD_WQE_PTR_VALID);
+			if (no_wptr)
+				cvmx_fpa_free(cvmx_phys_to_ptr
+					      ((uint64_t) ipd_wqe_ptr_valid.s.
+					       ptr << 7), CVMX_FPA_PACKET_POOL,
+					      0);
+			else
+				cvmx_fpa_free(cvmx_phys_to_ptr
+					      ((uint64_t) ipd_wqe_ptr_valid.s.
+					       ptr << 7), CVMX_FPA_WQE_POOL, 0);
+		}
+
+		/* Free all WQE in the fifo */
+		if (ipd_ptr_count.s.wqe_pcnt) {
+			int i;
+			union cvmx_ipd_pwp_ptr_fifo_ctl ipd_pwp_ptr_fifo_ctl;
+			ipd_pwp_ptr_fifo_ctl.u64 =
+			    cvmx_read_csr(CVMX_IPD_PWP_PTR_FIFO_CTL);
+			for (i = 0; i < ipd_ptr_count.s.wqe_pcnt; i++) {
+				ipd_pwp_ptr_fifo_ctl.s.cena = 0;
+				ipd_pwp_ptr_fifo_ctl.s.raddr =
+				    ipd_pwp_ptr_fifo_ctl.s.max_cnts +
+				    (ipd_pwp_ptr_fifo_ctl.s.wraddr +
+				     i) % ipd_pwp_ptr_fifo_ctl.s.max_cnts;
+				cvmx_write_csr(CVMX_IPD_PWP_PTR_FIFO_CTL,
+					       ipd_pwp_ptr_fifo_ctl.u64);
+				ipd_pwp_ptr_fifo_ctl.u64 =
+				    cvmx_read_csr(CVMX_IPD_PWP_PTR_FIFO_CTL);
+				if (no_wptr)
+					cvmx_fpa_free(cvmx_phys_to_ptr
+						      ((uint64_t)
+						       ipd_pwp_ptr_fifo_ctl.s.
+						       ptr << 7),
+						      CVMX_FPA_PACKET_POOL, 0);
+				else
+					cvmx_fpa_free(cvmx_phys_to_ptr
+						      ((uint64_t)
+						       ipd_pwp_ptr_fifo_ctl.s.
+						       ptr << 7),
+						      CVMX_FPA_WQE_POOL, 0);
+			}
+			ipd_pwp_ptr_fifo_ctl.s.cena = 1;
+			cvmx_write_csr(CVMX_IPD_PWP_PTR_FIFO_CTL,
+				       ipd_pwp_ptr_fifo_ctl.u64);
+		}
+
+		/* Free the prefetched packet */
+		if (ipd_ptr_count.s.pktv_cnt) {
+			union cvmx_ipd_pkt_ptr_valid ipd_pkt_ptr_valid;
+			ipd_pkt_ptr_valid.u64 =
+			    cvmx_read_csr(CVMX_IPD_PKT_PTR_VALID);
+			cvmx_fpa_free(cvmx_phys_to_ptr
+				      (ipd_pkt_ptr_valid.s.ptr << 7),
+				      CVMX_FPA_PACKET_POOL, 0);
+		}
+
+		/* Free the per port prefetched packets */
+		if (1) {
+			int i;
+			union cvmx_ipd_prc_port_ptr_fifo_ctl
+			    ipd_prc_port_ptr_fifo_ctl;
+			ipd_prc_port_ptr_fifo_ctl.u64 =
+			    cvmx_read_csr(CVMX_IPD_PRC_PORT_PTR_FIFO_CTL);
+
+			for (i = 0; i < ipd_prc_port_ptr_fifo_ctl.s.max_pkt;
+			     i++) {
+				ipd_prc_port_ptr_fifo_ctl.s.cena = 0;
+				ipd_prc_port_ptr_fifo_ctl.s.raddr =
+				    i % ipd_prc_port_ptr_fifo_ctl.s.max_pkt;
+				cvmx_write_csr(CVMX_IPD_PRC_PORT_PTR_FIFO_CTL,
+					       ipd_prc_port_ptr_fifo_ctl.u64);
+				ipd_prc_port_ptr_fifo_ctl.u64 =
+				    cvmx_read_csr
+				    (CVMX_IPD_PRC_PORT_PTR_FIFO_CTL);
+				cvmx_fpa_free(cvmx_phys_to_ptr
+					      ((uint64_t)
+					       ipd_prc_port_ptr_fifo_ctl.s.
+					       ptr << 7), CVMX_FPA_PACKET_POOL,
+					      0);
+			}
+			ipd_prc_port_ptr_fifo_ctl.s.cena = 1;
+			cvmx_write_csr(CVMX_IPD_PRC_PORT_PTR_FIFO_CTL,
+				       ipd_prc_port_ptr_fifo_ctl.u64);
+		}
+
+		/* Free all packets in the holding fifo */
+		if (ipd_ptr_count.s.pfif_cnt) {
+			int i;
+			union cvmx_ipd_prc_hold_ptr_fifo_ctl
+			    ipd_prc_hold_ptr_fifo_ctl;
+
+			ipd_prc_hold_ptr_fifo_ctl.u64 =
+			    cvmx_read_csr(CVMX_IPD_PRC_HOLD_PTR_FIFO_CTL);
+
+			for (i = 0; i < ipd_ptr_count.s.pfif_cnt; i++) {
+				ipd_prc_hold_ptr_fifo_ctl.s.cena = 0;
+				ipd_prc_hold_ptr_fifo_ctl.s.raddr =
+				    (ipd_prc_hold_ptr_fifo_ctl.s.praddr +
+				     i) % ipd_prc_hold_ptr_fifo_ctl.s.max_pkt;
+				cvmx_write_csr(CVMX_IPD_PRC_HOLD_PTR_FIFO_CTL,
+					       ipd_prc_hold_ptr_fifo_ctl.u64);
+				ipd_prc_hold_ptr_fifo_ctl.u64 =
+				    cvmx_read_csr
+				    (CVMX_IPD_PRC_HOLD_PTR_FIFO_CTL);
+				cvmx_fpa_free(cvmx_phys_to_ptr
+					      ((uint64_t)
+					       ipd_prc_hold_ptr_fifo_ctl.s.
+					       ptr << 7), CVMX_FPA_PACKET_POOL,
+					      0);
+			}
+			ipd_prc_hold_ptr_fifo_ctl.s.cena = 1;
+			cvmx_write_csr(CVMX_IPD_PRC_HOLD_PTR_FIFO_CTL,
+				       ipd_prc_hold_ptr_fifo_ctl.u64);
+		}
+
+		/* Free all packets in the fifo */
+		if (ipd_ptr_count.s.pkt_pcnt) {
+			int i;
+			union cvmx_ipd_pwp_ptr_fifo_ctl ipd_pwp_ptr_fifo_ctl;
+			ipd_pwp_ptr_fifo_ctl.u64 =
+			    cvmx_read_csr(CVMX_IPD_PWP_PTR_FIFO_CTL);
+
+			for (i = 0; i < ipd_ptr_count.s.pkt_pcnt; i++) {
+				ipd_pwp_ptr_fifo_ctl.s.cena = 0;
+				ipd_pwp_ptr_fifo_ctl.s.raddr =
+				    (ipd_pwp_ptr_fifo_ctl.s.praddr +
+				     i) % ipd_pwp_ptr_fifo_ctl.s.max_cnts;
+				cvmx_write_csr(CVMX_IPD_PWP_PTR_FIFO_CTL,
+					       ipd_pwp_ptr_fifo_ctl.u64);
+				ipd_pwp_ptr_fifo_ctl.u64 =
+				    cvmx_read_csr(CVMX_IPD_PWP_PTR_FIFO_CTL);
+				cvmx_fpa_free(cvmx_phys_to_ptr
+					      ((uint64_t) ipd_pwp_ptr_fifo_ctl.
+					       s.ptr << 7),
+					      CVMX_FPA_PACKET_POOL, 0);
+			}
+			ipd_pwp_ptr_fifo_ctl.s.cena = 1;
+			cvmx_write_csr(CVMX_IPD_PWP_PTR_FIFO_CTL,
+				       ipd_pwp_ptr_fifo_ctl.u64);
+		}
+
+		/* Reset the IPD to get all buffers out of it */
+		{
+			union cvmx_ipd_ctl_status ipd_ctl_status;
+			ipd_ctl_status.u64 = cvmx_read_csr(CVMX_IPD_CTL_STATUS);
+			ipd_ctl_status.s.reset = 1;
+			cvmx_write_csr(CVMX_IPD_CTL_STATUS, ipd_ctl_status.u64);
+		}
+
+		/* Reset the PIP */
+		{
+			union cvmx_pip_sft_rst pip_sft_rst;
+			pip_sft_rst.u64 = cvmx_read_csr(CVMX_PIP_SFT_RST);
+			pip_sft_rst.s.rst = 1;
+			cvmx_write_csr(CVMX_PIP_SFT_RST, pip_sft_rst.u64);
+		}
+	}
+}
+
+#endif /*  __CVMX_IPD_H__ */
diff --git a/arch/mips/include/asm/octeon/cvmx-l2c-defs.h b/arch/mips/include/asm/octeon/cvmx-l2c-defs.h
new file mode 100644
index 000000000..3ea84acf1
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-l2c-defs.h
@@ -0,0 +1,239 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2017 Cavium, Inc.
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_L2C_DEFS_H__
+#define __CVMX_L2C_DEFS_H__
+
+#include <uapi/asm/bitfield.h>
+
+#define CVMX_L2C_DBG (CVMX_ADD_IO_SEG(0x0001180080000030ull))
+#define CVMX_L2C_CFG (CVMX_ADD_IO_SEG(0x0001180080000000ull))
+#define CVMX_L2C_CTL (CVMX_ADD_IO_SEG(0x0001180080800000ull))
+#define CVMX_L2C_ERR_TDTX(block_id)					       \
+	(CVMX_ADD_IO_SEG(0x0001180080A007E0ull) + ((block_id) & 3) * 0x40000ull)
+#define CVMX_L2C_ERR_TTGX(block_id)					       \
+	(CVMX_ADD_IO_SEG(0x0001180080A007E8ull) + ((block_id) & 3) * 0x40000ull)
+#define CVMX_L2C_LCKBASE (CVMX_ADD_IO_SEG(0x0001180080000058ull))
+#define CVMX_L2C_LCKOFF (CVMX_ADD_IO_SEG(0x0001180080000060ull))
+#define CVMX_L2C_PFCTL (CVMX_ADD_IO_SEG(0x0001180080000090ull))
+#define CVMX_L2C_PFCX(offset) (CVMX_ADD_IO_SEG(0x0001180080000098ull) +	       \
+		((offset) & 3) * 8)
+#define CVMX_L2C_PFC0 CVMX_L2C_PFCX(0)
+#define CVMX_L2C_PFC1 CVMX_L2C_PFCX(1)
+#define CVMX_L2C_PFC2 CVMX_L2C_PFCX(2)
+#define CVMX_L2C_PFC3 CVMX_L2C_PFCX(3)
+#define CVMX_L2C_SPAR0 (CVMX_ADD_IO_SEG(0x0001180080000068ull))
+#define CVMX_L2C_SPAR1 (CVMX_ADD_IO_SEG(0x0001180080000070ull))
+#define CVMX_L2C_SPAR2 (CVMX_ADD_IO_SEG(0x0001180080000078ull))
+#define CVMX_L2C_SPAR3 (CVMX_ADD_IO_SEG(0x0001180080000080ull))
+#define CVMX_L2C_SPAR4 (CVMX_ADD_IO_SEG(0x0001180080000088ull))
+#define CVMX_L2C_TADX_PFCX(offset, block_id)				       \
+		(CVMX_ADD_IO_SEG(0x0001180080A00400ull) + (((offset) & 3) +    \
+		((block_id) & 7) * 0x8000ull) * 8)
+#define CVMX_L2C_TADX_PFC0(block_id) (CVMX_ADD_IO_SEG(0x0001180080A00400ull) + \
+		((block_id) & 3) * 0x40000ull)
+#define CVMX_L2C_TADX_PFC1(block_id) (CVMX_ADD_IO_SEG(0x0001180080A00408ull) + \
+		((block_id) & 3) * 0x40000ull)
+#define CVMX_L2C_TADX_PFC2(block_id) (CVMX_ADD_IO_SEG(0x0001180080A00410ull) + \
+		((block_id) & 3) * 0x40000ull)
+#define CVMX_L2C_TADX_PFC3(block_id) (CVMX_ADD_IO_SEG(0x0001180080A00418ull) + \
+		((block_id) & 3) * 0x40000ull)
+#define CVMX_L2C_TADX_PRF(offset) (CVMX_ADD_IO_SEG(0x0001180080A00008ull)    + \
+		((offset) & 7) * 0x40000ull)
+#define CVMX_L2C_TADX_TAG(block_id) (CVMX_ADD_IO_SEG(0x0001180080A00010ull)  + \
+		((block_id) & 3) * 0x40000ull)
+#define CVMX_L2C_WPAR_IOBX(offset) (CVMX_ADD_IO_SEG(0x0001180080840200ull)   + \
+		((offset) & 1) * 8)
+#define CVMX_L2C_WPAR_PPX(offset) (CVMX_ADD_IO_SEG(0x0001180080840000ull)    + \
+		((offset) & 31) * 8)
+
+
+union cvmx_l2c_err_tdtx {
+	uint64_t u64;
+	struct cvmx_l2c_err_tdtx_s {
+		__BITFIELD_FIELD(uint64_t dbe:1,
+		__BITFIELD_FIELD(uint64_t sbe:1,
+		__BITFIELD_FIELD(uint64_t vdbe:1,
+		__BITFIELD_FIELD(uint64_t vsbe:1,
+		__BITFIELD_FIELD(uint64_t syn:10,
+		__BITFIELD_FIELD(uint64_t reserved_22_49:28,
+		__BITFIELD_FIELD(uint64_t wayidx:18,
+		__BITFIELD_FIELD(uint64_t reserved_2_3:2,
+		__BITFIELD_FIELD(uint64_t type:2,
+		;)))))))))
+	} s;
+};
+
+union cvmx_l2c_err_ttgx {
+	uint64_t u64;
+	struct cvmx_l2c_err_ttgx_s {
+		__BITFIELD_FIELD(uint64_t dbe:1,
+		__BITFIELD_FIELD(uint64_t sbe:1,
+		__BITFIELD_FIELD(uint64_t noway:1,
+		__BITFIELD_FIELD(uint64_t reserved_56_60:5,
+		__BITFIELD_FIELD(uint64_t syn:6,
+		__BITFIELD_FIELD(uint64_t reserved_22_49:28,
+		__BITFIELD_FIELD(uint64_t wayidx:15,
+		__BITFIELD_FIELD(uint64_t reserved_2_6:5,
+		__BITFIELD_FIELD(uint64_t type:2,
+		;)))))))))
+	} s;
+};
+
+union cvmx_l2c_cfg {
+	uint64_t u64;
+	struct cvmx_l2c_cfg_s {
+		__BITFIELD_FIELD(uint64_t reserved_20_63:44,
+		__BITFIELD_FIELD(uint64_t bstrun:1,
+		__BITFIELD_FIELD(uint64_t lbist:1,
+		__BITFIELD_FIELD(uint64_t xor_bank:1,
+		__BITFIELD_FIELD(uint64_t dpres1:1,
+		__BITFIELD_FIELD(uint64_t dpres0:1,
+		__BITFIELD_FIELD(uint64_t dfill_dis:1,
+		__BITFIELD_FIELD(uint64_t fpexp:4,
+		__BITFIELD_FIELD(uint64_t fpempty:1,
+		__BITFIELD_FIELD(uint64_t fpen:1,
+		__BITFIELD_FIELD(uint64_t idxalias:1,
+		__BITFIELD_FIELD(uint64_t mwf_crd:4,
+		__BITFIELD_FIELD(uint64_t rsp_arb_mode:1,
+		__BITFIELD_FIELD(uint64_t rfb_arb_mode:1,
+		__BITFIELD_FIELD(uint64_t lrf_arb_mode:1,
+		;)))))))))))))))
+	} s;
+};
+
+union cvmx_l2c_ctl {
+	uint64_t u64;
+	struct cvmx_l2c_ctl_s {
+		__BITFIELD_FIELD(uint64_t reserved_30_63:34,
+		__BITFIELD_FIELD(uint64_t sepcmt:1,
+		__BITFIELD_FIELD(uint64_t rdf_fast:1,
+		__BITFIELD_FIELD(uint64_t disstgl2i:1,
+		__BITFIELD_FIELD(uint64_t l2dfsbe:1,
+		__BITFIELD_FIELD(uint64_t l2dfdbe:1,
+		__BITFIELD_FIELD(uint64_t discclk:1,
+		__BITFIELD_FIELD(uint64_t maxvab:4,
+		__BITFIELD_FIELD(uint64_t maxlfb:4,
+		__BITFIELD_FIELD(uint64_t rsp_arb_mode:1,
+		__BITFIELD_FIELD(uint64_t xmc_arb_mode:1,
+		__BITFIELD_FIELD(uint64_t ef_ena:1,
+		__BITFIELD_FIELD(uint64_t ef_cnt:7,
+		__BITFIELD_FIELD(uint64_t vab_thresh:4,
+		__BITFIELD_FIELD(uint64_t disecc:1,
+		__BITFIELD_FIELD(uint64_t disidxalias:1,
+		;))))))))))))))))
+	} s;
+};
+
+union cvmx_l2c_dbg {
+	uint64_t u64;
+	struct cvmx_l2c_dbg_s {
+		__BITFIELD_FIELD(uint64_t reserved_15_63:49,
+		__BITFIELD_FIELD(uint64_t lfb_enum:4,
+		__BITFIELD_FIELD(uint64_t lfb_dmp:1,
+		__BITFIELD_FIELD(uint64_t ppnum:4,
+		__BITFIELD_FIELD(uint64_t set:3,
+		__BITFIELD_FIELD(uint64_t finv:1,
+		__BITFIELD_FIELD(uint64_t l2d:1,
+		__BITFIELD_FIELD(uint64_t l2t:1,
+		;))))))))
+	} s;
+};
+
+union cvmx_l2c_pfctl {
+	uint64_t u64;
+	struct cvmx_l2c_pfctl_s {
+		__BITFIELD_FIELD(uint64_t reserved_36_63:28,
+		__BITFIELD_FIELD(uint64_t cnt3rdclr:1,
+		__BITFIELD_FIELD(uint64_t cnt2rdclr:1,
+		__BITFIELD_FIELD(uint64_t cnt1rdclr:1,
+		__BITFIELD_FIELD(uint64_t cnt0rdclr:1,
+		__BITFIELD_FIELD(uint64_t cnt3ena:1,
+		__BITFIELD_FIELD(uint64_t cnt3clr:1,
+		__BITFIELD_FIELD(uint64_t cnt3sel:6,
+		__BITFIELD_FIELD(uint64_t cnt2ena:1,
+		__BITFIELD_FIELD(uint64_t cnt2clr:1,
+		__BITFIELD_FIELD(uint64_t cnt2sel:6,
+		__BITFIELD_FIELD(uint64_t cnt1ena:1,
+		__BITFIELD_FIELD(uint64_t cnt1clr:1,
+		__BITFIELD_FIELD(uint64_t cnt1sel:6,
+		__BITFIELD_FIELD(uint64_t cnt0ena:1,
+		__BITFIELD_FIELD(uint64_t cnt0clr:1,
+		__BITFIELD_FIELD(uint64_t cnt0sel:6,
+		;)))))))))))))))))
+	} s;
+};
+
+union cvmx_l2c_tadx_prf {
+	uint64_t u64;
+	struct cvmx_l2c_tadx_prf_s {
+		__BITFIELD_FIELD(uint64_t reserved_32_63:32,
+		__BITFIELD_FIELD(uint64_t cnt3sel:8,
+		__BITFIELD_FIELD(uint64_t cnt2sel:8,
+		__BITFIELD_FIELD(uint64_t cnt1sel:8,
+		__BITFIELD_FIELD(uint64_t cnt0sel:8,
+		;)))))
+	} s;
+};
+
+union cvmx_l2c_tadx_tag {
+	uint64_t u64;
+	struct cvmx_l2c_tadx_tag_s {
+		__BITFIELD_FIELD(uint64_t reserved_46_63:18,
+		__BITFIELD_FIELD(uint64_t ecc:6,
+		__BITFIELD_FIELD(uint64_t reserved_36_39:4,
+		__BITFIELD_FIELD(uint64_t tag:19,
+		__BITFIELD_FIELD(uint64_t reserved_4_16:13,
+		__BITFIELD_FIELD(uint64_t use:1,
+		__BITFIELD_FIELD(uint64_t valid:1,
+		__BITFIELD_FIELD(uint64_t dirty:1,
+		__BITFIELD_FIELD(uint64_t lock:1,
+		;)))))))))
+	} s;
+};
+
+union cvmx_l2c_lckbase {
+	uint64_t u64;
+	struct cvmx_l2c_lckbase_s {
+		__BITFIELD_FIELD(uint64_t reserved_31_63:33,
+		__BITFIELD_FIELD(uint64_t lck_base:27,
+		__BITFIELD_FIELD(uint64_t reserved_1_3:3,
+		__BITFIELD_FIELD(uint64_t lck_ena:1,
+		;))))
+	} s;
+};
+
+union cvmx_l2c_lckoff {
+	uint64_t u64;
+	struct cvmx_l2c_lckoff_s {
+		__BITFIELD_FIELD(uint64_t reserved_10_63:54,
+		__BITFIELD_FIELD(uint64_t lck_offset:10,
+		;))
+	} s;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-l2c.h b/arch/mips/include/asm/octeon/cvmx-l2c.h
new file mode 100644
index 000000000..4459a3200
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-l2c.h
@@ -0,0 +1,364 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2017 Cavium, Inc.
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ * Interface to the Level 2 Cache (L2C) control, measurement, and debugging
+ * facilities.
+ */
+
+#ifndef __CVMX_L2C_H__
+#define __CVMX_L2C_H__
+
+#include <uapi/asm/bitfield.h>
+
+#define CVMX_L2_ASSOC	 cvmx_l2c_get_num_assoc()	/* Deprecated macro */
+#define CVMX_L2_SET_BITS cvmx_l2c_get_set_bits()	/* Deprecated macro */
+#define CVMX_L2_SETS	 cvmx_l2c_get_num_sets()	/* Deprecated macro */
+
+/* Based on 128 byte cache line size */
+#define CVMX_L2C_IDX_ADDR_SHIFT	7
+#define CVMX_L2C_IDX_MASK	(cvmx_l2c_get_num_sets() - 1)
+
+/* Defines for index aliasing computations */
+#define CVMX_L2C_TAG_ADDR_ALIAS_SHIFT (CVMX_L2C_IDX_ADDR_SHIFT +	       \
+		cvmx_l2c_get_set_bits())
+#define CVMX_L2C_ALIAS_MASK (CVMX_L2C_IDX_MASK << CVMX_L2C_TAG_ADDR_ALIAS_SHIFT)
+#define CVMX_L2C_MEMBANK_SELECT_SIZE 4096
+
+/* Number of L2C Tag-and-data sections (TADs) that are connected to LMC. */
+#define CVMX_L2C_TADS  1
+
+union cvmx_l2c_tag {
+	uint64_t u64;
+	struct {
+		__BITFIELD_FIELD(uint64_t reserved:28,
+		__BITFIELD_FIELD(uint64_t V:1,
+		__BITFIELD_FIELD(uint64_t D:1,
+		__BITFIELD_FIELD(uint64_t L:1,
+		__BITFIELD_FIELD(uint64_t U:1,
+		__BITFIELD_FIELD(uint64_t addr:32,
+		;))))))
+	} s;
+};
+
+/* L2C Performance Counter events. */
+enum cvmx_l2c_event {
+	CVMX_L2C_EVENT_CYCLES		=  0,
+	CVMX_L2C_EVENT_INSTRUCTION_MISS =  1,
+	CVMX_L2C_EVENT_INSTRUCTION_HIT	=  2,
+	CVMX_L2C_EVENT_DATA_MISS	=  3,
+	CVMX_L2C_EVENT_DATA_HIT		=  4,
+	CVMX_L2C_EVENT_MISS		=  5,
+	CVMX_L2C_EVENT_HIT		=  6,
+	CVMX_L2C_EVENT_VICTIM_HIT	=  7,
+	CVMX_L2C_EVENT_INDEX_CONFLICT	=  8,
+	CVMX_L2C_EVENT_TAG_PROBE	=  9,
+	CVMX_L2C_EVENT_TAG_UPDATE	= 10,
+	CVMX_L2C_EVENT_TAG_COMPLETE	= 11,
+	CVMX_L2C_EVENT_TAG_DIRTY	= 12,
+	CVMX_L2C_EVENT_DATA_STORE_NOP	= 13,
+	CVMX_L2C_EVENT_DATA_STORE_READ	= 14,
+	CVMX_L2C_EVENT_DATA_STORE_WRITE = 15,
+	CVMX_L2C_EVENT_FILL_DATA_VALID	= 16,
+	CVMX_L2C_EVENT_WRITE_REQUEST	= 17,
+	CVMX_L2C_EVENT_READ_REQUEST	= 18,
+	CVMX_L2C_EVENT_WRITE_DATA_VALID = 19,
+	CVMX_L2C_EVENT_XMC_NOP		= 20,
+	CVMX_L2C_EVENT_XMC_LDT		= 21,
+	CVMX_L2C_EVENT_XMC_LDI		= 22,
+	CVMX_L2C_EVENT_XMC_LDD		= 23,
+	CVMX_L2C_EVENT_XMC_STF		= 24,
+	CVMX_L2C_EVENT_XMC_STT		= 25,
+	CVMX_L2C_EVENT_XMC_STP		= 26,
+	CVMX_L2C_EVENT_XMC_STC		= 27,
+	CVMX_L2C_EVENT_XMC_DWB		= 28,
+	CVMX_L2C_EVENT_XMC_PL2		= 29,
+	CVMX_L2C_EVENT_XMC_PSL1		= 30,
+	CVMX_L2C_EVENT_XMC_IOBLD	= 31,
+	CVMX_L2C_EVENT_XMC_IOBST	= 32,
+	CVMX_L2C_EVENT_XMC_IOBDMA	= 33,
+	CVMX_L2C_EVENT_XMC_IOBRSP	= 34,
+	CVMX_L2C_EVENT_XMC_BUS_VALID	= 35,
+	CVMX_L2C_EVENT_XMC_MEM_DATA	= 36,
+	CVMX_L2C_EVENT_XMC_REFL_DATA	= 37,
+	CVMX_L2C_EVENT_XMC_IOBRSP_DATA	= 38,
+	CVMX_L2C_EVENT_RSC_NOP		= 39,
+	CVMX_L2C_EVENT_RSC_STDN		= 40,
+	CVMX_L2C_EVENT_RSC_FILL		= 41,
+	CVMX_L2C_EVENT_RSC_REFL		= 42,
+	CVMX_L2C_EVENT_RSC_STIN		= 43,
+	CVMX_L2C_EVENT_RSC_SCIN		= 44,
+	CVMX_L2C_EVENT_RSC_SCFL		= 45,
+	CVMX_L2C_EVENT_RSC_SCDN		= 46,
+	CVMX_L2C_EVENT_RSC_DATA_VALID	= 47,
+	CVMX_L2C_EVENT_RSC_VALID_FILL	= 48,
+	CVMX_L2C_EVENT_RSC_VALID_STRSP	= 49,
+	CVMX_L2C_EVENT_RSC_VALID_REFL	= 50,
+	CVMX_L2C_EVENT_LRF_REQ		= 51,
+	CVMX_L2C_EVENT_DT_RD_ALLOC	= 52,
+	CVMX_L2C_EVENT_DT_WR_INVAL	= 53,
+	CVMX_L2C_EVENT_MAX
+};
+
+/* L2C Performance Counter events for Octeon2. */
+enum cvmx_l2c_tad_event {
+	CVMX_L2C_TAD_EVENT_NONE		 = 0,
+	CVMX_L2C_TAD_EVENT_TAG_HIT	 = 1,
+	CVMX_L2C_TAD_EVENT_TAG_MISS	 = 2,
+	CVMX_L2C_TAD_EVENT_TAG_NOALLOC	 = 3,
+	CVMX_L2C_TAD_EVENT_TAG_VICTIM	 = 4,
+	CVMX_L2C_TAD_EVENT_SC_FAIL	 = 5,
+	CVMX_L2C_TAD_EVENT_SC_PASS	 = 6,
+	CVMX_L2C_TAD_EVENT_LFB_VALID	 = 7,
+	CVMX_L2C_TAD_EVENT_LFB_WAIT_LFB	 = 8,
+	CVMX_L2C_TAD_EVENT_LFB_WAIT_VAB	 = 9,
+	CVMX_L2C_TAD_EVENT_QUAD0_INDEX	 = 128,
+	CVMX_L2C_TAD_EVENT_QUAD0_READ	 = 129,
+	CVMX_L2C_TAD_EVENT_QUAD0_BANK	 = 130,
+	CVMX_L2C_TAD_EVENT_QUAD0_WDAT	 = 131,
+	CVMX_L2C_TAD_EVENT_QUAD1_INDEX	 = 144,
+	CVMX_L2C_TAD_EVENT_QUAD1_READ	 = 145,
+	CVMX_L2C_TAD_EVENT_QUAD1_BANK	 = 146,
+	CVMX_L2C_TAD_EVENT_QUAD1_WDAT	 = 147,
+	CVMX_L2C_TAD_EVENT_QUAD2_INDEX	 = 160,
+	CVMX_L2C_TAD_EVENT_QUAD2_READ	 = 161,
+	CVMX_L2C_TAD_EVENT_QUAD2_BANK	 = 162,
+	CVMX_L2C_TAD_EVENT_QUAD2_WDAT	 = 163,
+	CVMX_L2C_TAD_EVENT_QUAD3_INDEX	 = 176,
+	CVMX_L2C_TAD_EVENT_QUAD3_READ	 = 177,
+	CVMX_L2C_TAD_EVENT_QUAD3_BANK	 = 178,
+	CVMX_L2C_TAD_EVENT_QUAD3_WDAT	 = 179,
+	CVMX_L2C_TAD_EVENT_MAX
+};
+
+/**
+ * Configure one of the four L2 Cache performance counters to capture event
+ * occurrences.
+ *
+ * @counter:	    The counter to configure. Range 0..3.
+ * @event:	    The type of L2 Cache event occurrence to count.
+ * @clear_on_read:  When asserted, any read of the performance counter
+ *			 clears the counter.
+ *
+ * @note The routine does not clear the counter.
+ */
+void cvmx_l2c_config_perf(uint32_t counter, enum cvmx_l2c_event event,
+			  uint32_t clear_on_read);
+
+/**
+ * Read the given L2 Cache performance counter. The counter must be configured
+ * before reading, but this routine does not enforce this requirement.
+ *
+ * @counter:  The counter to configure. Range 0..3.
+ *
+ * Returns The current counter value.
+ */
+uint64_t cvmx_l2c_read_perf(uint32_t counter);
+
+/**
+ * Return the L2 Cache way partitioning for a given core.
+ *
+ * @core:  The core processor of interest.
+ *
+ * Returns    The mask specifying the partitioning. 0 bits in mask indicates
+ *		the cache 'ways' that a core can evict from.
+ *	      -1 on error
+ */
+int cvmx_l2c_get_core_way_partition(uint32_t core);
+
+/**
+ * Partitions the L2 cache for a core
+ *
+ * @core: The core that the partitioning applies to.
+ * @mask: The partitioning of the ways expressed as a binary
+ *	       mask. A 0 bit allows the core to evict cache lines from
+ *	       a way, while a 1 bit blocks the core from evicting any
+ *	       lines from that way. There must be at least one allowed
+ *	       way (0 bit) in the mask.
+ *
+
+ * @note If any ways are blocked for all cores and the HW blocks, then
+ *	 those ways will never have any cache lines evicted from them.
+ *	 All cores and the hardware blocks are free to read from all
+ *	 ways regardless of the partitioning.
+ */
+int cvmx_l2c_set_core_way_partition(uint32_t core, uint32_t mask);
+
+/**
+ * Return the L2 Cache way partitioning for the hw blocks.
+ *
+ * Returns    The mask specifying the reserved way. 0 bits in mask indicates
+ *		the cache 'ways' that a core can evict from.
+ *	      -1 on error
+ */
+int cvmx_l2c_get_hw_way_partition(void);
+
+/**
+ * Partitions the L2 cache for the hardware blocks.
+ *
+ * @mask: The partitioning of the ways expressed as a binary
+ *	       mask. A 0 bit allows the core to evict cache lines from
+ *	       a way, while a 1 bit blocks the core from evicting any
+ *	       lines from that way. There must be at least one allowed
+ *	       way (0 bit) in the mask.
+ *
+
+ * @note If any ways are blocked for all cores and the HW blocks, then
+ *	 those ways will never have any cache lines evicted from them.
+ *	 All cores and the hardware blocks are free to read from all
+ *	 ways regardless of the partitioning.
+ */
+int cvmx_l2c_set_hw_way_partition(uint32_t mask);
+
+
+/**
+ * Locks a line in the L2 cache at the specified physical address
+ *
+ * @addr:   physical address of line to lock
+ *
+ * Returns 0 on success,
+ *	   1 if line not locked.
+ */
+int cvmx_l2c_lock_line(uint64_t addr);
+
+/**
+ * Locks a specified memory region in the L2 cache.
+ *
+ * Note that if not all lines can be locked, that means that all
+ * but one of the ways (associations) available to the locking
+ * core are locked.  Having only 1 association available for
+ * normal caching may have a significant adverse affect on performance.
+ * Care should be taken to ensure that enough of the L2 cache is left
+ * unlocked to allow for normal caching of DRAM.
+ *
+ * @start:  Physical address of the start of the region to lock
+ * @len:    Length (in bytes) of region to lock
+ *
+ * Returns Number of requested lines that where not locked.
+ *	   0 on success (all locked)
+ */
+int cvmx_l2c_lock_mem_region(uint64_t start, uint64_t len);
+
+/**
+ * Unlock and flush a cache line from the L2 cache.
+ * IMPORTANT: Must only be run by one core at a time due to use
+ * of L2C debug features.
+ * Note that this function will flush a matching but unlocked cache line.
+ * (If address is not in L2, no lines are flushed.)
+ *
+ * @address: Physical address to unlock
+ *
+ * Returns 0: line not unlocked
+ *	   1: line unlocked
+ */
+int cvmx_l2c_unlock_line(uint64_t address);
+
+/**
+ * Unlocks a region of memory that is locked in the L2 cache
+ *
+ * @start:  start physical address
+ * @len:    length (in bytes) to unlock
+ *
+ * Returns Number of locked lines that the call unlocked
+ */
+int cvmx_l2c_unlock_mem_region(uint64_t start, uint64_t len);
+
+/**
+ * Read the L2 controller tag for a given location in L2
+ *
+ * @association:
+ *		 Which association to read line from
+ * @index:  Which way to read from.
+ *
+ * Returns l2c tag structure for line requested.
+ */
+union cvmx_l2c_tag cvmx_l2c_get_tag(uint32_t association, uint32_t index);
+
+/* Wrapper providing a deprecated old function name */
+static inline union cvmx_l2c_tag cvmx_get_l2c_tag(uint32_t association,
+						  uint32_t index)
+						  __attribute__((deprecated));
+static inline union cvmx_l2c_tag cvmx_get_l2c_tag(uint32_t association,
+						  uint32_t index)
+{
+	return cvmx_l2c_get_tag(association, index);
+}
+
+
+/**
+ * Returns the cache index for a given physical address
+ *
+ * @addr:   physical address
+ *
+ * Returns L2 cache index
+ */
+uint32_t cvmx_l2c_address_to_index(uint64_t addr);
+
+/**
+ * Flushes (and unlocks) the entire L2 cache.
+ * IMPORTANT: Must only be run by one core at a time due to use
+ * of L2C debug features.
+ */
+void cvmx_l2c_flush(void);
+
+/**
+ *
+ * Returns the size of the L2 cache in bytes,
+ * -1 on error (unrecognized model)
+ */
+int cvmx_l2c_get_cache_size_bytes(void);
+
+/**
+ * Return the number of sets in the L2 Cache
+ *
+ * Returns
+ */
+int cvmx_l2c_get_num_sets(void);
+
+/**
+ * Return log base 2 of the number of sets in the L2 cache
+ * Returns
+ */
+int cvmx_l2c_get_set_bits(void);
+/**
+ * Return the number of associations in the L2 Cache
+ *
+ * Returns
+ */
+int cvmx_l2c_get_num_assoc(void);
+
+/**
+ * Flush a line from the L2 cache
+ * This should only be called from one core at a time, as this routine
+ * sets the core to the 'debug' core in order to flush the line.
+ *
+ * @assoc:  Association (or way) to flush
+ * @index:  Index to flush
+ */
+void cvmx_l2c_flush_line(uint32_t assoc, uint32_t index);
+
+#endif /* __CVMX_L2C_H__ */
diff --git a/arch/mips/include/asm/octeon/cvmx-l2d-defs.h b/arch/mips/include/asm/octeon/cvmx-l2d-defs.h
new file mode 100644
index 000000000..a951ad5d6
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-l2d-defs.h
@@ -0,0 +1,60 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2017 Cavium, Inc.
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_L2D_DEFS_H__
+#define __CVMX_L2D_DEFS_H__
+
+#define CVMX_L2D_ERR	(CVMX_ADD_IO_SEG(0x0001180080000010ull))
+#define CVMX_L2D_FUS3	(CVMX_ADD_IO_SEG(0x00011800800007B8ull))
+
+
+union cvmx_l2d_err {
+	uint64_t u64;
+	struct cvmx_l2d_err_s {
+		__BITFIELD_FIELD(uint64_t reserved_6_63:58,
+		__BITFIELD_FIELD(uint64_t bmhclsel:1,
+		__BITFIELD_FIELD(uint64_t ded_err:1,
+		__BITFIELD_FIELD(uint64_t sec_err:1,
+		__BITFIELD_FIELD(uint64_t ded_intena:1,
+		__BITFIELD_FIELD(uint64_t sec_intena:1,
+		__BITFIELD_FIELD(uint64_t ecc_ena:1,
+		;)))))))
+	} s;
+};
+
+union cvmx_l2d_fus3 {
+	uint64_t u64;
+	struct cvmx_l2d_fus3_s {
+		__BITFIELD_FIELD(uint64_t reserved_40_63:24,
+		__BITFIELD_FIELD(uint64_t ema_ctl:3,
+		__BITFIELD_FIELD(uint64_t reserved_34_36:3,
+		__BITFIELD_FIELD(uint64_t q3fus:34,
+		;))))
+	} s;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-l2t-defs.h b/arch/mips/include/asm/octeon/cvmx-l2t-defs.h
new file mode 100644
index 000000000..06ea13251
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-l2t-defs.h
@@ -0,0 +1,143 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2017 Cavium, Inc.
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_L2T_DEFS_H__
+#define __CVMX_L2T_DEFS_H__
+
+#include <uapi/asm/bitfield.h>
+
+#define CVMX_L2T_ERR	(CVMX_ADD_IO_SEG(0x0001180080000008ull))
+
+
+union cvmx_l2t_err {
+	uint64_t u64;
+	struct cvmx_l2t_err_s {
+		__BITFIELD_FIELD(uint64_t reserved_29_63:35,
+		__BITFIELD_FIELD(uint64_t fadru:1,
+		__BITFIELD_FIELD(uint64_t lck_intena2:1,
+		__BITFIELD_FIELD(uint64_t lckerr2:1,
+		__BITFIELD_FIELD(uint64_t lck_intena:1,
+		__BITFIELD_FIELD(uint64_t lckerr:1,
+		__BITFIELD_FIELD(uint64_t fset:3,
+		__BITFIELD_FIELD(uint64_t fadr:10,
+		__BITFIELD_FIELD(uint64_t fsyn:6,
+		__BITFIELD_FIELD(uint64_t ded_err:1,
+		__BITFIELD_FIELD(uint64_t sec_err:1,
+		__BITFIELD_FIELD(uint64_t ded_intena:1,
+		__BITFIELD_FIELD(uint64_t sec_intena:1,
+		__BITFIELD_FIELD(uint64_t ecc_ena:1,
+		;))))))))))))))
+	} s;
+	struct cvmx_l2t_err_cn30xx {
+		__BITFIELD_FIELD(uint64_t reserved_28_63:36,
+		__BITFIELD_FIELD(uint64_t lck_intena2:1,
+		__BITFIELD_FIELD(uint64_t lckerr2:1,
+		__BITFIELD_FIELD(uint64_t lck_intena:1,
+		__BITFIELD_FIELD(uint64_t lckerr:1,
+		__BITFIELD_FIELD(uint64_t reserved_23_23:1,
+		__BITFIELD_FIELD(uint64_t fset:2,
+		__BITFIELD_FIELD(uint64_t reserved_19_20:2,
+		__BITFIELD_FIELD(uint64_t fadr:8,
+		__BITFIELD_FIELD(uint64_t fsyn:6,
+		__BITFIELD_FIELD(uint64_t ded_err:1,
+		__BITFIELD_FIELD(uint64_t sec_err:1,
+		__BITFIELD_FIELD(uint64_t ded_intena:1,
+		__BITFIELD_FIELD(uint64_t sec_intena:1,
+		__BITFIELD_FIELD(uint64_t ecc_ena:1,
+		;)))))))))))))))
+	} cn30xx;
+	struct cvmx_l2t_err_cn31xx {
+		__BITFIELD_FIELD(uint64_t reserved_28_63:36,
+		__BITFIELD_FIELD(uint64_t lck_intena2:1,
+		__BITFIELD_FIELD(uint64_t lckerr2:1,
+		__BITFIELD_FIELD(uint64_t lck_intena:1,
+		__BITFIELD_FIELD(uint64_t lckerr:1,
+		__BITFIELD_FIELD(uint64_t reserved_23_23:1,
+		__BITFIELD_FIELD(uint64_t fset:2,
+		__BITFIELD_FIELD(uint64_t reserved_20_20:1,
+		__BITFIELD_FIELD(uint64_t fadr:9,
+		__BITFIELD_FIELD(uint64_t fsyn:6,
+		__BITFIELD_FIELD(uint64_t ded_err:1,
+		__BITFIELD_FIELD(uint64_t sec_err:1,
+		__BITFIELD_FIELD(uint64_t ded_intena:1,
+		__BITFIELD_FIELD(uint64_t sec_intena:1,
+		__BITFIELD_FIELD(uint64_t ecc_ena:1,
+		;)))))))))))))))
+	} cn31xx;
+	struct cvmx_l2t_err_cn38xx {
+		__BITFIELD_FIELD(uint64_t reserved_28_63:36,
+		__BITFIELD_FIELD(uint64_t lck_intena2:1,
+		__BITFIELD_FIELD(uint64_t lckerr2:1,
+		__BITFIELD_FIELD(uint64_t lck_intena:1,
+		__BITFIELD_FIELD(uint64_t lckerr:1,
+		__BITFIELD_FIELD(uint64_t fset:3,
+		__BITFIELD_FIELD(uint64_t fadr:10,
+		__BITFIELD_FIELD(uint64_t fsyn:6,
+		__BITFIELD_FIELD(uint64_t ded_err:1,
+		__BITFIELD_FIELD(uint64_t sec_err:1,
+		__BITFIELD_FIELD(uint64_t ded_intena:1,
+		__BITFIELD_FIELD(uint64_t sec_intena:1,
+		__BITFIELD_FIELD(uint64_t ecc_ena:1,
+		;)))))))))))))
+	} cn38xx;
+	struct cvmx_l2t_err_cn50xx {
+		__BITFIELD_FIELD(uint64_t reserved_28_63:36,
+		__BITFIELD_FIELD(uint64_t lck_intena2:1,
+		__BITFIELD_FIELD(uint64_t lckerr2:1,
+		__BITFIELD_FIELD(uint64_t lck_intena:1,
+		__BITFIELD_FIELD(uint64_t lckerr:1,
+		__BITFIELD_FIELD(uint64_t fset:3,
+		__BITFIELD_FIELD(uint64_t reserved_18_20:3,
+		__BITFIELD_FIELD(uint64_t fadr:7,
+		__BITFIELD_FIELD(uint64_t fsyn:6,
+		__BITFIELD_FIELD(uint64_t ded_err:1,
+		__BITFIELD_FIELD(uint64_t sec_err:1,
+		__BITFIELD_FIELD(uint64_t ded_intena:1,
+		__BITFIELD_FIELD(uint64_t sec_intena:1,
+		__BITFIELD_FIELD(uint64_t ecc_ena:1,
+		;))))))))))))))
+	} cn50xx;
+	struct cvmx_l2t_err_cn52xx {
+		__BITFIELD_FIELD(uint64_t reserved_28_63:36,
+		__BITFIELD_FIELD(uint64_t lck_intena2:1,
+		__BITFIELD_FIELD(uint64_t lckerr2:1,
+		__BITFIELD_FIELD(uint64_t lck_intena:1,
+		__BITFIELD_FIELD(uint64_t lckerr:1,
+		__BITFIELD_FIELD(uint64_t fset:3,
+		__BITFIELD_FIELD(uint64_t reserved_20_20:1,
+		__BITFIELD_FIELD(uint64_t fadr:9,
+		__BITFIELD_FIELD(uint64_t fsyn:6,
+		__BITFIELD_FIELD(uint64_t ded_err:1,
+		__BITFIELD_FIELD(uint64_t sec_err:1,
+		__BITFIELD_FIELD(uint64_t ded_intena:1,
+		__BITFIELD_FIELD(uint64_t sec_intena:1,
+		__BITFIELD_FIELD(uint64_t ecc_ena:1,
+		;))))))))))))))
+	} cn52xx;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-led-defs.h b/arch/mips/include/asm/octeon/cvmx-led-defs.h
new file mode 100644
index 000000000..023790752
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-led-defs.h
@@ -0,0 +1,214 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2012 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_LED_DEFS_H__
+#define __CVMX_LED_DEFS_H__
+
+#define CVMX_LED_BLINK (CVMX_ADD_IO_SEG(0x0001180000001A48ull))
+#define CVMX_LED_CLK_PHASE (CVMX_ADD_IO_SEG(0x0001180000001A08ull))
+#define CVMX_LED_CYLON (CVMX_ADD_IO_SEG(0x0001180000001AF8ull))
+#define CVMX_LED_DBG (CVMX_ADD_IO_SEG(0x0001180000001A18ull))
+#define CVMX_LED_EN (CVMX_ADD_IO_SEG(0x0001180000001A00ull))
+#define CVMX_LED_POLARITY (CVMX_ADD_IO_SEG(0x0001180000001A50ull))
+#define CVMX_LED_PRT (CVMX_ADD_IO_SEG(0x0001180000001A10ull))
+#define CVMX_LED_PRT_FMT (CVMX_ADD_IO_SEG(0x0001180000001A30ull))
+#define CVMX_LED_PRT_STATUSX(offset) (CVMX_ADD_IO_SEG(0x0001180000001A80ull) + ((offset) & 7) * 8)
+#define CVMX_LED_UDD_CNTX(offset) (CVMX_ADD_IO_SEG(0x0001180000001A20ull) + ((offset) & 1) * 8)
+#define CVMX_LED_UDD_DATX(offset) (CVMX_ADD_IO_SEG(0x0001180000001A38ull) + ((offset) & 1) * 8)
+#define CVMX_LED_UDD_DAT_CLRX(offset) (CVMX_ADD_IO_SEG(0x0001180000001AC8ull) + ((offset) & 1) * 16)
+#define CVMX_LED_UDD_DAT_SETX(offset) (CVMX_ADD_IO_SEG(0x0001180000001AC0ull) + ((offset) & 1) * 16)
+
+union cvmx_led_blink {
+	uint64_t u64;
+	struct cvmx_led_blink_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t rate:8;
+#else
+		uint64_t rate:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_led_clk_phase {
+	uint64_t u64;
+	struct cvmx_led_clk_phase_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t phase:7;
+#else
+		uint64_t phase:7;
+		uint64_t reserved_7_63:57;
+#endif
+	} s;
+};
+
+union cvmx_led_cylon {
+	uint64_t u64;
+	struct cvmx_led_cylon_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t rate:16;
+#else
+		uint64_t rate:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_led_dbg {
+	uint64_t u64;
+	struct cvmx_led_dbg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t dbg_en:1;
+#else
+		uint64_t dbg_en:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_led_en {
+	uint64_t u64;
+	struct cvmx_led_en_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t en:1;
+#else
+		uint64_t en:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_led_polarity {
+	uint64_t u64;
+	struct cvmx_led_polarity_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t polarity:1;
+#else
+		uint64_t polarity:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_led_prt {
+	uint64_t u64;
+	struct cvmx_led_prt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t prt_en:8;
+#else
+		uint64_t prt_en:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_led_prt_fmt {
+	uint64_t u64;
+	struct cvmx_led_prt_fmt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t format:4;
+#else
+		uint64_t format:4;
+		uint64_t reserved_4_63:60;
+#endif
+	} s;
+};
+
+union cvmx_led_prt_statusx {
+	uint64_t u64;
+	struct cvmx_led_prt_statusx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t status:6;
+#else
+		uint64_t status:6;
+		uint64_t reserved_6_63:58;
+#endif
+	} s;
+};
+
+union cvmx_led_udd_cntx {
+	uint64_t u64;
+	struct cvmx_led_udd_cntx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t cnt:6;
+#else
+		uint64_t cnt:6;
+		uint64_t reserved_6_63:58;
+#endif
+	} s;
+};
+
+union cvmx_led_udd_datx {
+	uint64_t u64;
+	struct cvmx_led_udd_datx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t dat:32;
+#else
+		uint64_t dat:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_led_udd_dat_clrx {
+	uint64_t u64;
+	struct cvmx_led_udd_dat_clrx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t clr:32;
+#else
+		uint64_t clr:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_led_udd_dat_setx {
+	uint64_t u64;
+	struct cvmx_led_udd_dat_setx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t set:32;
+#else
+		uint64_t set:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-lmcx-defs.h b/arch/mips/include/asm/octeon/cvmx-lmcx-defs.h
new file mode 100644
index 000000000..4167a4c7a
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-lmcx-defs.h
@@ -0,0 +1,2943 @@
+/***********************license start***************
+ * Author: Cavium Inc.
+ *
+ * Contact: support@cavium.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2012 Cavium Inc.
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Inc. for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_LMCX_DEFS_H__
+#define __CVMX_LMCX_DEFS_H__
+
+#define CVMX_LMCX_BIST_CTL(block_id) (CVMX_ADD_IO_SEG(0x00011800880000F0ull) + ((block_id) & 1) * 0x60000000ull)
+#define CVMX_LMCX_BIST_RESULT(block_id) (CVMX_ADD_IO_SEG(0x00011800880000F8ull) + ((block_id) & 1) * 0x60000000ull)
+#define CVMX_LMCX_CHAR_CTL(block_id) (CVMX_ADD_IO_SEG(0x0001180088000220ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_CHAR_MASK0(block_id) (CVMX_ADD_IO_SEG(0x0001180088000228ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_CHAR_MASK1(block_id) (CVMX_ADD_IO_SEG(0x0001180088000230ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_CHAR_MASK2(block_id) (CVMX_ADD_IO_SEG(0x0001180088000238ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_CHAR_MASK3(block_id) (CVMX_ADD_IO_SEG(0x0001180088000240ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_CHAR_MASK4(block_id) (CVMX_ADD_IO_SEG(0x0001180088000318ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_COMP_CTL(block_id) (CVMX_ADD_IO_SEG(0x0001180088000028ull) + ((block_id) & 1) * 0x60000000ull)
+#define CVMX_LMCX_COMP_CTL2(block_id) (CVMX_ADD_IO_SEG(0x00011800880001B8ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_CONFIG(block_id) (CVMX_ADD_IO_SEG(0x0001180088000188ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_CONTROL(block_id) (CVMX_ADD_IO_SEG(0x0001180088000190ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_CTL(block_id) (CVMX_ADD_IO_SEG(0x0001180088000010ull) + ((block_id) & 1) * 0x60000000ull)
+#define CVMX_LMCX_CTL1(block_id) (CVMX_ADD_IO_SEG(0x0001180088000090ull) + ((block_id) & 1) * 0x60000000ull)
+#define CVMX_LMCX_DCLK_CNT(block_id) (CVMX_ADD_IO_SEG(0x00011800880001E0ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_DCLK_CNT_HI(block_id) (CVMX_ADD_IO_SEG(0x0001180088000070ull) + ((block_id) & 1) * 0x60000000ull)
+#define CVMX_LMCX_DCLK_CNT_LO(block_id) (CVMX_ADD_IO_SEG(0x0001180088000068ull) + ((block_id) & 1) * 0x60000000ull)
+#define CVMX_LMCX_DCLK_CTL(block_id) (CVMX_ADD_IO_SEG(0x00011800880000B8ull) + ((block_id) & 1) * 0x60000000ull)
+#define CVMX_LMCX_DDR2_CTL(block_id) (CVMX_ADD_IO_SEG(0x0001180088000018ull) + ((block_id) & 1) * 0x60000000ull)
+#define CVMX_LMCX_DDR_PLL_CTL(block_id) (CVMX_ADD_IO_SEG(0x0001180088000258ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_DELAY_CFG(block_id) (CVMX_ADD_IO_SEG(0x0001180088000088ull) + ((block_id) & 1) * 0x60000000ull)
+#define CVMX_LMCX_DIMMX_PARAMS(offset, block_id) (CVMX_ADD_IO_SEG(0x0001180088000270ull) + (((offset) & 1) + ((block_id) & 3) * 0x200000ull) * 8)
+#define CVMX_LMCX_DIMM_CTL(block_id) (CVMX_ADD_IO_SEG(0x0001180088000310ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_DLL_CTL(block_id) (CVMX_ADD_IO_SEG(0x00011800880000C0ull) + ((block_id) & 1) * 0x60000000ull)
+#define CVMX_LMCX_DLL_CTL2(block_id) (CVMX_ADD_IO_SEG(0x00011800880001C8ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_DLL_CTL3(block_id) (CVMX_ADD_IO_SEG(0x0001180088000218ull) + ((block_id) & 3) * 0x1000000ull)
+static inline uint64_t CVMX_LMCX_DUAL_MEMCFG(unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CNF71XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN50XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN58XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180088000098ull) + (block_id) * 0x60000000ull;
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180088000098ull) + (block_id) * 0x60000000ull;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180088000098ull) + (block_id) * 0x1000000ull;
+	}
+	return CVMX_ADD_IO_SEG(0x0001180088000098ull) + (block_id) * 0x60000000ull;
+}
+
+static inline uint64_t CVMX_LMCX_ECC_SYND(unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN30XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN50XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN38XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN31XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN58XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CNF71XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180088000038ull) + (block_id) * 0x60000000ull;
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180088000038ull) + (block_id) * 0x60000000ull;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180088000038ull) + (block_id) * 0x1000000ull;
+	}
+	return CVMX_ADD_IO_SEG(0x0001180088000038ull) + (block_id) * 0x60000000ull;
+}
+
+static inline uint64_t CVMX_LMCX_FADR(unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN30XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN50XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN38XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN31XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN58XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CNF71XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180088000020ull) + (block_id) * 0x60000000ull;
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180088000020ull) + (block_id) * 0x60000000ull;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x0001180088000020ull) + (block_id) * 0x1000000ull;
+	}
+	return CVMX_ADD_IO_SEG(0x0001180088000020ull) + (block_id) * 0x60000000ull;
+}
+
+#define CVMX_LMCX_IFB_CNT(block_id) (CVMX_ADD_IO_SEG(0x00011800880001D0ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_IFB_CNT_HI(block_id) (CVMX_ADD_IO_SEG(0x0001180088000050ull) + ((block_id) & 1) * 0x60000000ull)
+#define CVMX_LMCX_IFB_CNT_LO(block_id) (CVMX_ADD_IO_SEG(0x0001180088000048ull) + ((block_id) & 1) * 0x60000000ull)
+#define CVMX_LMCX_INT(block_id) (CVMX_ADD_IO_SEG(0x00011800880001F0ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_INT_EN(block_id) (CVMX_ADD_IO_SEG(0x00011800880001E8ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_MEM_CFG0(block_id) (CVMX_ADD_IO_SEG(0x0001180088000000ull) + ((block_id) & 1) * 0x60000000ull)
+#define CVMX_LMCX_MEM_CFG1(block_id) (CVMX_ADD_IO_SEG(0x0001180088000008ull) + ((block_id) & 1) * 0x60000000ull)
+#define CVMX_LMCX_MODEREG_PARAMS0(block_id) (CVMX_ADD_IO_SEG(0x00011800880001A8ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_MODEREG_PARAMS1(block_id) (CVMX_ADD_IO_SEG(0x0001180088000260ull) + ((block_id) & 3) * 0x1000000ull)
+static inline uint64_t CVMX_LMCX_NXM(unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CNF71XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN58XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800880000C8ull) + (block_id) * 0x60000000ull;
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800880000C8ull) + (block_id) * 0x60000000ull;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800880000C8ull) + (block_id) * 0x1000000ull;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800880000C8ull) + (block_id) * 0x60000000ull;
+}
+
+#define CVMX_LMCX_OPS_CNT(block_id) (CVMX_ADD_IO_SEG(0x00011800880001D8ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_OPS_CNT_HI(block_id) (CVMX_ADD_IO_SEG(0x0001180088000060ull) + ((block_id) & 1) * 0x60000000ull)
+#define CVMX_LMCX_OPS_CNT_LO(block_id) (CVMX_ADD_IO_SEG(0x0001180088000058ull) + ((block_id) & 1) * 0x60000000ull)
+#define CVMX_LMCX_PHY_CTL(block_id) (CVMX_ADD_IO_SEG(0x0001180088000210ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_PLL_BWCTL(block_id) (CVMX_ADD_IO_SEG(0x0001180088000040ull))
+#define CVMX_LMCX_PLL_CTL(block_id) (CVMX_ADD_IO_SEG(0x00011800880000A8ull) + ((block_id) & 1) * 0x60000000ull)
+#define CVMX_LMCX_PLL_STATUS(block_id) (CVMX_ADD_IO_SEG(0x00011800880000B0ull) + ((block_id) & 1) * 0x60000000ull)
+#define CVMX_LMCX_READ_LEVEL_CTL(block_id) (CVMX_ADD_IO_SEG(0x0001180088000140ull) + ((block_id) & 1) * 0x60000000ull)
+#define CVMX_LMCX_READ_LEVEL_DBG(block_id) (CVMX_ADD_IO_SEG(0x0001180088000148ull) + ((block_id) & 1) * 0x60000000ull)
+#define CVMX_LMCX_READ_LEVEL_RANKX(offset, block_id) (CVMX_ADD_IO_SEG(0x0001180088000100ull) + (((offset) & 3) + ((block_id) & 1) * 0xC000000ull) * 8)
+#define CVMX_LMCX_RESET_CTL(block_id) (CVMX_ADD_IO_SEG(0x0001180088000180ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_RLEVEL_CTL(block_id) (CVMX_ADD_IO_SEG(0x00011800880002A0ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_RLEVEL_DBG(block_id) (CVMX_ADD_IO_SEG(0x00011800880002A8ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_RLEVEL_RANKX(offset, block_id) (CVMX_ADD_IO_SEG(0x0001180088000280ull) + (((offset) & 3) + ((block_id) & 3) * 0x200000ull) * 8)
+#define CVMX_LMCX_RODT_COMP_CTL(block_id) (CVMX_ADD_IO_SEG(0x00011800880000A0ull) + ((block_id) & 1) * 0x60000000ull)
+#define CVMX_LMCX_RODT_CTL(block_id) (CVMX_ADD_IO_SEG(0x0001180088000078ull) + ((block_id) & 1) * 0x60000000ull)
+#define CVMX_LMCX_RODT_MASK(block_id) (CVMX_ADD_IO_SEG(0x0001180088000268ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_SCRAMBLED_FADR(block_id) (CVMX_ADD_IO_SEG(0x0001180088000330ull))
+#define CVMX_LMCX_SCRAMBLE_CFG0(block_id) (CVMX_ADD_IO_SEG(0x0001180088000320ull))
+#define CVMX_LMCX_SCRAMBLE_CFG1(block_id) (CVMX_ADD_IO_SEG(0x0001180088000328ull))
+#define CVMX_LMCX_SLOT_CTL0(block_id) (CVMX_ADD_IO_SEG(0x00011800880001F8ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_SLOT_CTL1(block_id) (CVMX_ADD_IO_SEG(0x0001180088000200ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_SLOT_CTL2(block_id) (CVMX_ADD_IO_SEG(0x0001180088000208ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_TIMING_PARAMS0(block_id) (CVMX_ADD_IO_SEG(0x0001180088000198ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_TIMING_PARAMS1(block_id) (CVMX_ADD_IO_SEG(0x00011800880001A0ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_TRO_CTL(block_id) (CVMX_ADD_IO_SEG(0x0001180088000248ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_TRO_STAT(block_id) (CVMX_ADD_IO_SEG(0x0001180088000250ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_WLEVEL_CTL(block_id) (CVMX_ADD_IO_SEG(0x0001180088000300ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_WLEVEL_DBG(block_id) (CVMX_ADD_IO_SEG(0x0001180088000308ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_LMCX_WLEVEL_RANKX(offset, block_id) (CVMX_ADD_IO_SEG(0x00011800880002B0ull) + (((offset) & 3) + ((block_id) & 3) * 0x200000ull) * 8)
+#define CVMX_LMCX_WODT_CTL0(block_id) (CVMX_ADD_IO_SEG(0x0001180088000030ull) + ((block_id) & 1) * 0x60000000ull)
+#define CVMX_LMCX_WODT_CTL1(block_id) (CVMX_ADD_IO_SEG(0x0001180088000080ull) + ((block_id) & 1) * 0x60000000ull)
+#define CVMX_LMCX_WODT_MASK(block_id) (CVMX_ADD_IO_SEG(0x00011800880001B0ull) + ((block_id) & 3) * 0x1000000ull)
+
+union cvmx_lmcx_bist_ctl {
+	uint64_t u64;
+	struct cvmx_lmcx_bist_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t start:1;
+#else
+		uint64_t start:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_bist_result {
+	uint64_t u64;
+	struct cvmx_lmcx_bist_result_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_11_63:53;
+		uint64_t csrd2e:1;
+		uint64_t csre2d:1;
+		uint64_t mwf:1;
+		uint64_t mwd:3;
+		uint64_t mwc:1;
+		uint64_t mrf:1;
+		uint64_t mrd:3;
+#else
+		uint64_t mrd:3;
+		uint64_t mrf:1;
+		uint64_t mwc:1;
+		uint64_t mwd:3;
+		uint64_t mwf:1;
+		uint64_t csre2d:1;
+		uint64_t csrd2e:1;
+		uint64_t reserved_11_63:53;
+#endif
+	} s;
+	struct cvmx_lmcx_bist_result_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_9_63:55;
+		uint64_t mwf:1;
+		uint64_t mwd:3;
+		uint64_t mwc:1;
+		uint64_t mrf:1;
+		uint64_t mrd:3;
+#else
+		uint64_t mrd:3;
+		uint64_t mrf:1;
+		uint64_t mwc:1;
+		uint64_t mwd:3;
+		uint64_t mwf:1;
+		uint64_t reserved_9_63:55;
+#endif
+	} cn50xx;
+};
+
+union cvmx_lmcx_char_ctl {
+	uint64_t u64;
+	struct cvmx_lmcx_char_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_44_63:20;
+		uint64_t dr:1;
+		uint64_t skew_on:1;
+		uint64_t en:1;
+		uint64_t sel:1;
+		uint64_t prog:8;
+		uint64_t prbs:32;
+#else
+		uint64_t prbs:32;
+		uint64_t prog:8;
+		uint64_t sel:1;
+		uint64_t en:1;
+		uint64_t skew_on:1;
+		uint64_t dr:1;
+		uint64_t reserved_44_63:20;
+#endif
+	} s;
+	struct cvmx_lmcx_char_ctl_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_42_63:22;
+		uint64_t en:1;
+		uint64_t sel:1;
+		uint64_t prog:8;
+		uint64_t prbs:32;
+#else
+		uint64_t prbs:32;
+		uint64_t prog:8;
+		uint64_t sel:1;
+		uint64_t en:1;
+		uint64_t reserved_42_63:22;
+#endif
+	} cn63xx;
+};
+
+union cvmx_lmcx_char_mask0 {
+	uint64_t u64;
+	struct cvmx_lmcx_char_mask0_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t mask:64;
+#else
+		uint64_t mask:64;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_char_mask1 {
+	uint64_t u64;
+	struct cvmx_lmcx_char_mask1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t mask:8;
+#else
+		uint64_t mask:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_char_mask2 {
+	uint64_t u64;
+	struct cvmx_lmcx_char_mask2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t mask:64;
+#else
+		uint64_t mask:64;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_char_mask3 {
+	uint64_t u64;
+	struct cvmx_lmcx_char_mask3_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t mask:8;
+#else
+		uint64_t mask:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_char_mask4 {
+	uint64_t u64;
+	struct cvmx_lmcx_char_mask4_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_33_63:31;
+		uint64_t reset_n_mask:1;
+		uint64_t a_mask:16;
+		uint64_t ba_mask:3;
+		uint64_t we_n_mask:1;
+		uint64_t cas_n_mask:1;
+		uint64_t ras_n_mask:1;
+		uint64_t odt1_mask:2;
+		uint64_t odt0_mask:2;
+		uint64_t cs1_n_mask:2;
+		uint64_t cs0_n_mask:2;
+		uint64_t cke_mask:2;
+#else
+		uint64_t cke_mask:2;
+		uint64_t cs0_n_mask:2;
+		uint64_t cs1_n_mask:2;
+		uint64_t odt0_mask:2;
+		uint64_t odt1_mask:2;
+		uint64_t ras_n_mask:1;
+		uint64_t cas_n_mask:1;
+		uint64_t we_n_mask:1;
+		uint64_t ba_mask:3;
+		uint64_t a_mask:16;
+		uint64_t reset_n_mask:1;
+		uint64_t reserved_33_63:31;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_comp_ctl {
+	uint64_t u64;
+	struct cvmx_lmcx_comp_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t nctl_csr:4;
+		uint64_t nctl_clk:4;
+		uint64_t nctl_cmd:4;
+		uint64_t nctl_dat:4;
+		uint64_t pctl_csr:4;
+		uint64_t pctl_clk:4;
+		uint64_t reserved_0_7:8;
+#else
+		uint64_t reserved_0_7:8;
+		uint64_t pctl_clk:4;
+		uint64_t pctl_csr:4;
+		uint64_t nctl_dat:4;
+		uint64_t nctl_cmd:4;
+		uint64_t nctl_clk:4;
+		uint64_t nctl_csr:4;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+	struct cvmx_lmcx_comp_ctl_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t nctl_csr:4;
+		uint64_t nctl_clk:4;
+		uint64_t nctl_cmd:4;
+		uint64_t nctl_dat:4;
+		uint64_t pctl_csr:4;
+		uint64_t pctl_clk:4;
+		uint64_t pctl_cmd:4;
+		uint64_t pctl_dat:4;
+#else
+		uint64_t pctl_dat:4;
+		uint64_t pctl_cmd:4;
+		uint64_t pctl_clk:4;
+		uint64_t pctl_csr:4;
+		uint64_t nctl_dat:4;
+		uint64_t nctl_cmd:4;
+		uint64_t nctl_clk:4;
+		uint64_t nctl_csr:4;
+		uint64_t reserved_32_63:32;
+#endif
+	} cn30xx;
+	struct cvmx_lmcx_comp_ctl_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t nctl_csr:4;
+		uint64_t reserved_20_27:8;
+		uint64_t nctl_dat:4;
+		uint64_t pctl_csr:4;
+		uint64_t reserved_5_11:7;
+		uint64_t pctl_dat:5;
+#else
+		uint64_t pctl_dat:5;
+		uint64_t reserved_5_11:7;
+		uint64_t pctl_csr:4;
+		uint64_t nctl_dat:4;
+		uint64_t reserved_20_27:8;
+		uint64_t nctl_csr:4;
+		uint64_t reserved_32_63:32;
+#endif
+	} cn50xx;
+	struct cvmx_lmcx_comp_ctl_cn58xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t nctl_csr:4;
+		uint64_t reserved_20_27:8;
+		uint64_t nctl_dat:4;
+		uint64_t pctl_csr:4;
+		uint64_t reserved_4_11:8;
+		uint64_t pctl_dat:4;
+#else
+		uint64_t pctl_dat:4;
+		uint64_t reserved_4_11:8;
+		uint64_t pctl_csr:4;
+		uint64_t nctl_dat:4;
+		uint64_t reserved_20_27:8;
+		uint64_t nctl_csr:4;
+		uint64_t reserved_32_63:32;
+#endif
+	} cn58xxp1;
+};
+
+union cvmx_lmcx_comp_ctl2 {
+	uint64_t u64;
+	struct cvmx_lmcx_comp_ctl2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_34_63:30;
+		uint64_t ddr__ptune:4;
+		uint64_t ddr__ntune:4;
+		uint64_t m180:1;
+		uint64_t byp:1;
+		uint64_t ptune:4;
+		uint64_t ntune:4;
+		uint64_t rodt_ctl:4;
+		uint64_t cmd_ctl:4;
+		uint64_t ck_ctl:4;
+		uint64_t dqx_ctl:4;
+#else
+		uint64_t dqx_ctl:4;
+		uint64_t ck_ctl:4;
+		uint64_t cmd_ctl:4;
+		uint64_t rodt_ctl:4;
+		uint64_t ntune:4;
+		uint64_t ptune:4;
+		uint64_t byp:1;
+		uint64_t m180:1;
+		uint64_t ddr__ntune:4;
+		uint64_t ddr__ptune:4;
+		uint64_t reserved_34_63:30;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_config {
+	uint64_t u64;
+	struct cvmx_lmcx_config_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_61_63:3;
+		uint64_t mode32b:1;
+		uint64_t scrz:1;
+		uint64_t early_unload_d1_r1:1;
+		uint64_t early_unload_d1_r0:1;
+		uint64_t early_unload_d0_r1:1;
+		uint64_t early_unload_d0_r0:1;
+		uint64_t init_status:4;
+		uint64_t mirrmask:4;
+		uint64_t rankmask:4;
+		uint64_t rank_ena:1;
+		uint64_t sref_with_dll:1;
+		uint64_t early_dqx:1;
+		uint64_t sequence:3;
+		uint64_t ref_zqcs_int:19;
+		uint64_t reset:1;
+		uint64_t ecc_adr:1;
+		uint64_t forcewrite:4;
+		uint64_t idlepower:3;
+		uint64_t pbank_lsb:4;
+		uint64_t row_lsb:3;
+		uint64_t ecc_ena:1;
+		uint64_t init_start:1;
+#else
+		uint64_t init_start:1;
+		uint64_t ecc_ena:1;
+		uint64_t row_lsb:3;
+		uint64_t pbank_lsb:4;
+		uint64_t idlepower:3;
+		uint64_t forcewrite:4;
+		uint64_t ecc_adr:1;
+		uint64_t reset:1;
+		uint64_t ref_zqcs_int:19;
+		uint64_t sequence:3;
+		uint64_t early_dqx:1;
+		uint64_t sref_with_dll:1;
+		uint64_t rank_ena:1;
+		uint64_t rankmask:4;
+		uint64_t mirrmask:4;
+		uint64_t init_status:4;
+		uint64_t early_unload_d0_r0:1;
+		uint64_t early_unload_d0_r1:1;
+		uint64_t early_unload_d1_r0:1;
+		uint64_t early_unload_d1_r1:1;
+		uint64_t scrz:1;
+		uint64_t mode32b:1;
+		uint64_t reserved_61_63:3;
+#endif
+	} s;
+	struct cvmx_lmcx_config_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_59_63:5;
+		uint64_t early_unload_d1_r1:1;
+		uint64_t early_unload_d1_r0:1;
+		uint64_t early_unload_d0_r1:1;
+		uint64_t early_unload_d0_r0:1;
+		uint64_t init_status:4;
+		uint64_t mirrmask:4;
+		uint64_t rankmask:4;
+		uint64_t rank_ena:1;
+		uint64_t sref_with_dll:1;
+		uint64_t early_dqx:1;
+		uint64_t sequence:3;
+		uint64_t ref_zqcs_int:19;
+		uint64_t reset:1;
+		uint64_t ecc_adr:1;
+		uint64_t forcewrite:4;
+		uint64_t idlepower:3;
+		uint64_t pbank_lsb:4;
+		uint64_t row_lsb:3;
+		uint64_t ecc_ena:1;
+		uint64_t init_start:1;
+#else
+		uint64_t init_start:1;
+		uint64_t ecc_ena:1;
+		uint64_t row_lsb:3;
+		uint64_t pbank_lsb:4;
+		uint64_t idlepower:3;
+		uint64_t forcewrite:4;
+		uint64_t ecc_adr:1;
+		uint64_t reset:1;
+		uint64_t ref_zqcs_int:19;
+		uint64_t sequence:3;
+		uint64_t early_dqx:1;
+		uint64_t sref_with_dll:1;
+		uint64_t rank_ena:1;
+		uint64_t rankmask:4;
+		uint64_t mirrmask:4;
+		uint64_t init_status:4;
+		uint64_t early_unload_d0_r0:1;
+		uint64_t early_unload_d0_r1:1;
+		uint64_t early_unload_d1_r0:1;
+		uint64_t early_unload_d1_r1:1;
+		uint64_t reserved_59_63:5;
+#endif
+	} cn63xx;
+	struct cvmx_lmcx_config_cn63xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_55_63:9;
+		uint64_t init_status:4;
+		uint64_t mirrmask:4;
+		uint64_t rankmask:4;
+		uint64_t rank_ena:1;
+		uint64_t sref_with_dll:1;
+		uint64_t early_dqx:1;
+		uint64_t sequence:3;
+		uint64_t ref_zqcs_int:19;
+		uint64_t reset:1;
+		uint64_t ecc_adr:1;
+		uint64_t forcewrite:4;
+		uint64_t idlepower:3;
+		uint64_t pbank_lsb:4;
+		uint64_t row_lsb:3;
+		uint64_t ecc_ena:1;
+		uint64_t init_start:1;
+#else
+		uint64_t init_start:1;
+		uint64_t ecc_ena:1;
+		uint64_t row_lsb:3;
+		uint64_t pbank_lsb:4;
+		uint64_t idlepower:3;
+		uint64_t forcewrite:4;
+		uint64_t ecc_adr:1;
+		uint64_t reset:1;
+		uint64_t ref_zqcs_int:19;
+		uint64_t sequence:3;
+		uint64_t early_dqx:1;
+		uint64_t sref_with_dll:1;
+		uint64_t rank_ena:1;
+		uint64_t rankmask:4;
+		uint64_t mirrmask:4;
+		uint64_t init_status:4;
+		uint64_t reserved_55_63:9;
+#endif
+	} cn63xxp1;
+	struct cvmx_lmcx_config_cn66xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_60_63:4;
+		uint64_t scrz:1;
+		uint64_t early_unload_d1_r1:1;
+		uint64_t early_unload_d1_r0:1;
+		uint64_t early_unload_d0_r1:1;
+		uint64_t early_unload_d0_r0:1;
+		uint64_t init_status:4;
+		uint64_t mirrmask:4;
+		uint64_t rankmask:4;
+		uint64_t rank_ena:1;
+		uint64_t sref_with_dll:1;
+		uint64_t early_dqx:1;
+		uint64_t sequence:3;
+		uint64_t ref_zqcs_int:19;
+		uint64_t reset:1;
+		uint64_t ecc_adr:1;
+		uint64_t forcewrite:4;
+		uint64_t idlepower:3;
+		uint64_t pbank_lsb:4;
+		uint64_t row_lsb:3;
+		uint64_t ecc_ena:1;
+		uint64_t init_start:1;
+#else
+		uint64_t init_start:1;
+		uint64_t ecc_ena:1;
+		uint64_t row_lsb:3;
+		uint64_t pbank_lsb:4;
+		uint64_t idlepower:3;
+		uint64_t forcewrite:4;
+		uint64_t ecc_adr:1;
+		uint64_t reset:1;
+		uint64_t ref_zqcs_int:19;
+		uint64_t sequence:3;
+		uint64_t early_dqx:1;
+		uint64_t sref_with_dll:1;
+		uint64_t rank_ena:1;
+		uint64_t rankmask:4;
+		uint64_t mirrmask:4;
+		uint64_t init_status:4;
+		uint64_t early_unload_d0_r0:1;
+		uint64_t early_unload_d0_r1:1;
+		uint64_t early_unload_d1_r0:1;
+		uint64_t early_unload_d1_r1:1;
+		uint64_t scrz:1;
+		uint64_t reserved_60_63:4;
+#endif
+	} cn66xx;
+};
+
+union cvmx_lmcx_control {
+	uint64_t u64;
+	struct cvmx_lmcx_control_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t scramble_ena:1;
+		uint64_t thrcnt:12;
+		uint64_t persub:8;
+		uint64_t thrmax:4;
+		uint64_t crm_cnt:5;
+		uint64_t crm_thr:5;
+		uint64_t crm_max:5;
+		uint64_t rodt_bprch:1;
+		uint64_t wodt_bprch:1;
+		uint64_t bprch:2;
+		uint64_t ext_zqcs_dis:1;
+		uint64_t int_zqcs_dis:1;
+		uint64_t auto_dclkdis:1;
+		uint64_t xor_bank:1;
+		uint64_t max_write_batch:4;
+		uint64_t nxm_write_en:1;
+		uint64_t elev_prio_dis:1;
+		uint64_t inorder_wr:1;
+		uint64_t inorder_rd:1;
+		uint64_t throttle_wr:1;
+		uint64_t throttle_rd:1;
+		uint64_t fprch2:2;
+		uint64_t pocas:1;
+		uint64_t ddr2t:1;
+		uint64_t bwcnt:1;
+		uint64_t rdimm_ena:1;
+#else
+		uint64_t rdimm_ena:1;
+		uint64_t bwcnt:1;
+		uint64_t ddr2t:1;
+		uint64_t pocas:1;
+		uint64_t fprch2:2;
+		uint64_t throttle_rd:1;
+		uint64_t throttle_wr:1;
+		uint64_t inorder_rd:1;
+		uint64_t inorder_wr:1;
+		uint64_t elev_prio_dis:1;
+		uint64_t nxm_write_en:1;
+		uint64_t max_write_batch:4;
+		uint64_t xor_bank:1;
+		uint64_t auto_dclkdis:1;
+		uint64_t int_zqcs_dis:1;
+		uint64_t ext_zqcs_dis:1;
+		uint64_t bprch:2;
+		uint64_t wodt_bprch:1;
+		uint64_t rodt_bprch:1;
+		uint64_t crm_max:5;
+		uint64_t crm_thr:5;
+		uint64_t crm_cnt:5;
+		uint64_t thrmax:4;
+		uint64_t persub:8;
+		uint64_t thrcnt:12;
+		uint64_t scramble_ena:1;
+#endif
+	} s;
+	struct cvmx_lmcx_control_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_24_63:40;
+		uint64_t rodt_bprch:1;
+		uint64_t wodt_bprch:1;
+		uint64_t bprch:2;
+		uint64_t ext_zqcs_dis:1;
+		uint64_t int_zqcs_dis:1;
+		uint64_t auto_dclkdis:1;
+		uint64_t xor_bank:1;
+		uint64_t max_write_batch:4;
+		uint64_t nxm_write_en:1;
+		uint64_t elev_prio_dis:1;
+		uint64_t inorder_wr:1;
+		uint64_t inorder_rd:1;
+		uint64_t throttle_wr:1;
+		uint64_t throttle_rd:1;
+		uint64_t fprch2:2;
+		uint64_t pocas:1;
+		uint64_t ddr2t:1;
+		uint64_t bwcnt:1;
+		uint64_t rdimm_ena:1;
+#else
+		uint64_t rdimm_ena:1;
+		uint64_t bwcnt:1;
+		uint64_t ddr2t:1;
+		uint64_t pocas:1;
+		uint64_t fprch2:2;
+		uint64_t throttle_rd:1;
+		uint64_t throttle_wr:1;
+		uint64_t inorder_rd:1;
+		uint64_t inorder_wr:1;
+		uint64_t elev_prio_dis:1;
+		uint64_t nxm_write_en:1;
+		uint64_t max_write_batch:4;
+		uint64_t xor_bank:1;
+		uint64_t auto_dclkdis:1;
+		uint64_t int_zqcs_dis:1;
+		uint64_t ext_zqcs_dis:1;
+		uint64_t bprch:2;
+		uint64_t wodt_bprch:1;
+		uint64_t rodt_bprch:1;
+		uint64_t reserved_24_63:40;
+#endif
+	} cn63xx;
+	struct cvmx_lmcx_control_cn66xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t scramble_ena:1;
+		uint64_t reserved_24_62:39;
+		uint64_t rodt_bprch:1;
+		uint64_t wodt_bprch:1;
+		uint64_t bprch:2;
+		uint64_t ext_zqcs_dis:1;
+		uint64_t int_zqcs_dis:1;
+		uint64_t auto_dclkdis:1;
+		uint64_t xor_bank:1;
+		uint64_t max_write_batch:4;
+		uint64_t nxm_write_en:1;
+		uint64_t elev_prio_dis:1;
+		uint64_t inorder_wr:1;
+		uint64_t inorder_rd:1;
+		uint64_t throttle_wr:1;
+		uint64_t throttle_rd:1;
+		uint64_t fprch2:2;
+		uint64_t pocas:1;
+		uint64_t ddr2t:1;
+		uint64_t bwcnt:1;
+		uint64_t rdimm_ena:1;
+#else
+		uint64_t rdimm_ena:1;
+		uint64_t bwcnt:1;
+		uint64_t ddr2t:1;
+		uint64_t pocas:1;
+		uint64_t fprch2:2;
+		uint64_t throttle_rd:1;
+		uint64_t throttle_wr:1;
+		uint64_t inorder_rd:1;
+		uint64_t inorder_wr:1;
+		uint64_t elev_prio_dis:1;
+		uint64_t nxm_write_en:1;
+		uint64_t max_write_batch:4;
+		uint64_t xor_bank:1;
+		uint64_t auto_dclkdis:1;
+		uint64_t int_zqcs_dis:1;
+		uint64_t ext_zqcs_dis:1;
+		uint64_t bprch:2;
+		uint64_t wodt_bprch:1;
+		uint64_t rodt_bprch:1;
+		uint64_t reserved_24_62:39;
+		uint64_t scramble_ena:1;
+#endif
+	} cn66xx;
+	struct cvmx_lmcx_control_cn68xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_63_63:1;
+		uint64_t thrcnt:12;
+		uint64_t persub:8;
+		uint64_t thrmax:4;
+		uint64_t crm_cnt:5;
+		uint64_t crm_thr:5;
+		uint64_t crm_max:5;
+		uint64_t rodt_bprch:1;
+		uint64_t wodt_bprch:1;
+		uint64_t bprch:2;
+		uint64_t ext_zqcs_dis:1;
+		uint64_t int_zqcs_dis:1;
+		uint64_t auto_dclkdis:1;
+		uint64_t xor_bank:1;
+		uint64_t max_write_batch:4;
+		uint64_t nxm_write_en:1;
+		uint64_t elev_prio_dis:1;
+		uint64_t inorder_wr:1;
+		uint64_t inorder_rd:1;
+		uint64_t throttle_wr:1;
+		uint64_t throttle_rd:1;
+		uint64_t fprch2:2;
+		uint64_t pocas:1;
+		uint64_t ddr2t:1;
+		uint64_t bwcnt:1;
+		uint64_t rdimm_ena:1;
+#else
+		uint64_t rdimm_ena:1;
+		uint64_t bwcnt:1;
+		uint64_t ddr2t:1;
+		uint64_t pocas:1;
+		uint64_t fprch2:2;
+		uint64_t throttle_rd:1;
+		uint64_t throttle_wr:1;
+		uint64_t inorder_rd:1;
+		uint64_t inorder_wr:1;
+		uint64_t elev_prio_dis:1;
+		uint64_t nxm_write_en:1;
+		uint64_t max_write_batch:4;
+		uint64_t xor_bank:1;
+		uint64_t auto_dclkdis:1;
+		uint64_t int_zqcs_dis:1;
+		uint64_t ext_zqcs_dis:1;
+		uint64_t bprch:2;
+		uint64_t wodt_bprch:1;
+		uint64_t rodt_bprch:1;
+		uint64_t crm_max:5;
+		uint64_t crm_thr:5;
+		uint64_t crm_cnt:5;
+		uint64_t thrmax:4;
+		uint64_t persub:8;
+		uint64_t thrcnt:12;
+		uint64_t reserved_63_63:1;
+#endif
+	} cn68xx;
+};
+
+union cvmx_lmcx_ctl {
+	uint64_t u64;
+	struct cvmx_lmcx_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t ddr__nctl:4;
+		uint64_t ddr__pctl:4;
+		uint64_t slow_scf:1;
+		uint64_t xor_bank:1;
+		uint64_t max_write_batch:4;
+		uint64_t pll_div2:1;
+		uint64_t pll_bypass:1;
+		uint64_t rdimm_ena:1;
+		uint64_t r2r_slot:1;
+		uint64_t inorder_mwf:1;
+		uint64_t inorder_mrf:1;
+		uint64_t reserved_10_11:2;
+		uint64_t fprch2:1;
+		uint64_t bprch:1;
+		uint64_t sil_lat:2;
+		uint64_t tskw:2;
+		uint64_t qs_dic:2;
+		uint64_t dic:2;
+#else
+		uint64_t dic:2;
+		uint64_t qs_dic:2;
+		uint64_t tskw:2;
+		uint64_t sil_lat:2;
+		uint64_t bprch:1;
+		uint64_t fprch2:1;
+		uint64_t reserved_10_11:2;
+		uint64_t inorder_mrf:1;
+		uint64_t inorder_mwf:1;
+		uint64_t r2r_slot:1;
+		uint64_t rdimm_ena:1;
+		uint64_t pll_bypass:1;
+		uint64_t pll_div2:1;
+		uint64_t max_write_batch:4;
+		uint64_t xor_bank:1;
+		uint64_t slow_scf:1;
+		uint64_t ddr__pctl:4;
+		uint64_t ddr__nctl:4;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+	struct cvmx_lmcx_ctl_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t ddr__nctl:4;
+		uint64_t ddr__pctl:4;
+		uint64_t slow_scf:1;
+		uint64_t xor_bank:1;
+		uint64_t max_write_batch:4;
+		uint64_t pll_div2:1;
+		uint64_t pll_bypass:1;
+		uint64_t rdimm_ena:1;
+		uint64_t r2r_slot:1;
+		uint64_t inorder_mwf:1;
+		uint64_t inorder_mrf:1;
+		uint64_t dreset:1;
+		uint64_t mode32b:1;
+		uint64_t fprch2:1;
+		uint64_t bprch:1;
+		uint64_t sil_lat:2;
+		uint64_t tskw:2;
+		uint64_t qs_dic:2;
+		uint64_t dic:2;
+#else
+		uint64_t dic:2;
+		uint64_t qs_dic:2;
+		uint64_t tskw:2;
+		uint64_t sil_lat:2;
+		uint64_t bprch:1;
+		uint64_t fprch2:1;
+		uint64_t mode32b:1;
+		uint64_t dreset:1;
+		uint64_t inorder_mrf:1;
+		uint64_t inorder_mwf:1;
+		uint64_t r2r_slot:1;
+		uint64_t rdimm_ena:1;
+		uint64_t pll_bypass:1;
+		uint64_t pll_div2:1;
+		uint64_t max_write_batch:4;
+		uint64_t xor_bank:1;
+		uint64_t slow_scf:1;
+		uint64_t ddr__pctl:4;
+		uint64_t ddr__nctl:4;
+		uint64_t reserved_32_63:32;
+#endif
+	} cn30xx;
+	struct cvmx_lmcx_ctl_cn38xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t ddr__nctl:4;
+		uint64_t ddr__pctl:4;
+		uint64_t slow_scf:1;
+		uint64_t xor_bank:1;
+		uint64_t max_write_batch:4;
+		uint64_t reserved_16_17:2;
+		uint64_t rdimm_ena:1;
+		uint64_t r2r_slot:1;
+		uint64_t inorder_mwf:1;
+		uint64_t inorder_mrf:1;
+		uint64_t set_zero:1;
+		uint64_t mode128b:1;
+		uint64_t fprch2:1;
+		uint64_t bprch:1;
+		uint64_t sil_lat:2;
+		uint64_t tskw:2;
+		uint64_t qs_dic:2;
+		uint64_t dic:2;
+#else
+		uint64_t dic:2;
+		uint64_t qs_dic:2;
+		uint64_t tskw:2;
+		uint64_t sil_lat:2;
+		uint64_t bprch:1;
+		uint64_t fprch2:1;
+		uint64_t mode128b:1;
+		uint64_t set_zero:1;
+		uint64_t inorder_mrf:1;
+		uint64_t inorder_mwf:1;
+		uint64_t r2r_slot:1;
+		uint64_t rdimm_ena:1;
+		uint64_t reserved_16_17:2;
+		uint64_t max_write_batch:4;
+		uint64_t xor_bank:1;
+		uint64_t slow_scf:1;
+		uint64_t ddr__pctl:4;
+		uint64_t ddr__nctl:4;
+		uint64_t reserved_32_63:32;
+#endif
+	} cn38xx;
+	struct cvmx_lmcx_ctl_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t ddr__nctl:4;
+		uint64_t ddr__pctl:4;
+		uint64_t slow_scf:1;
+		uint64_t xor_bank:1;
+		uint64_t max_write_batch:4;
+		uint64_t reserved_17_17:1;
+		uint64_t pll_bypass:1;
+		uint64_t rdimm_ena:1;
+		uint64_t r2r_slot:1;
+		uint64_t inorder_mwf:1;
+		uint64_t inorder_mrf:1;
+		uint64_t dreset:1;
+		uint64_t mode32b:1;
+		uint64_t fprch2:1;
+		uint64_t bprch:1;
+		uint64_t sil_lat:2;
+		uint64_t tskw:2;
+		uint64_t qs_dic:2;
+		uint64_t dic:2;
+#else
+		uint64_t dic:2;
+		uint64_t qs_dic:2;
+		uint64_t tskw:2;
+		uint64_t sil_lat:2;
+		uint64_t bprch:1;
+		uint64_t fprch2:1;
+		uint64_t mode32b:1;
+		uint64_t dreset:1;
+		uint64_t inorder_mrf:1;
+		uint64_t inorder_mwf:1;
+		uint64_t r2r_slot:1;
+		uint64_t rdimm_ena:1;
+		uint64_t pll_bypass:1;
+		uint64_t reserved_17_17:1;
+		uint64_t max_write_batch:4;
+		uint64_t xor_bank:1;
+		uint64_t slow_scf:1;
+		uint64_t ddr__pctl:4;
+		uint64_t ddr__nctl:4;
+		uint64_t reserved_32_63:32;
+#endif
+	} cn50xx;
+	struct cvmx_lmcx_ctl_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t ddr__nctl:4;
+		uint64_t ddr__pctl:4;
+		uint64_t slow_scf:1;
+		uint64_t xor_bank:1;
+		uint64_t max_write_batch:4;
+		uint64_t reserved_16_17:2;
+		uint64_t rdimm_ena:1;
+		uint64_t r2r_slot:1;
+		uint64_t inorder_mwf:1;
+		uint64_t inorder_mrf:1;
+		uint64_t dreset:1;
+		uint64_t mode32b:1;
+		uint64_t fprch2:1;
+		uint64_t bprch:1;
+		uint64_t sil_lat:2;
+		uint64_t tskw:2;
+		uint64_t qs_dic:2;
+		uint64_t dic:2;
+#else
+		uint64_t dic:2;
+		uint64_t qs_dic:2;
+		uint64_t tskw:2;
+		uint64_t sil_lat:2;
+		uint64_t bprch:1;
+		uint64_t fprch2:1;
+		uint64_t mode32b:1;
+		uint64_t dreset:1;
+		uint64_t inorder_mrf:1;
+		uint64_t inorder_mwf:1;
+		uint64_t r2r_slot:1;
+		uint64_t rdimm_ena:1;
+		uint64_t reserved_16_17:2;
+		uint64_t max_write_batch:4;
+		uint64_t xor_bank:1;
+		uint64_t slow_scf:1;
+		uint64_t ddr__pctl:4;
+		uint64_t ddr__nctl:4;
+		uint64_t reserved_32_63:32;
+#endif
+	} cn52xx;
+	struct cvmx_lmcx_ctl_cn58xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t ddr__nctl:4;
+		uint64_t ddr__pctl:4;
+		uint64_t slow_scf:1;
+		uint64_t xor_bank:1;
+		uint64_t max_write_batch:4;
+		uint64_t reserved_16_17:2;
+		uint64_t rdimm_ena:1;
+		uint64_t r2r_slot:1;
+		uint64_t inorder_mwf:1;
+		uint64_t inorder_mrf:1;
+		uint64_t dreset:1;
+		uint64_t mode128b:1;
+		uint64_t fprch2:1;
+		uint64_t bprch:1;
+		uint64_t sil_lat:2;
+		uint64_t tskw:2;
+		uint64_t qs_dic:2;
+		uint64_t dic:2;
+#else
+		uint64_t dic:2;
+		uint64_t qs_dic:2;
+		uint64_t tskw:2;
+		uint64_t sil_lat:2;
+		uint64_t bprch:1;
+		uint64_t fprch2:1;
+		uint64_t mode128b:1;
+		uint64_t dreset:1;
+		uint64_t inorder_mrf:1;
+		uint64_t inorder_mwf:1;
+		uint64_t r2r_slot:1;
+		uint64_t rdimm_ena:1;
+		uint64_t reserved_16_17:2;
+		uint64_t max_write_batch:4;
+		uint64_t xor_bank:1;
+		uint64_t slow_scf:1;
+		uint64_t ddr__pctl:4;
+		uint64_t ddr__nctl:4;
+		uint64_t reserved_32_63:32;
+#endif
+	} cn58xx;
+};
+
+union cvmx_lmcx_ctl1 {
+	uint64_t u64;
+	struct cvmx_lmcx_ctl1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_21_63:43;
+		uint64_t ecc_adr:1;
+		uint64_t forcewrite:4;
+		uint64_t idlepower:3;
+		uint64_t sequence:3;
+		uint64_t sil_mode:1;
+		uint64_t dcc_enable:1;
+		uint64_t reserved_2_7:6;
+		uint64_t data_layout:2;
+#else
+		uint64_t data_layout:2;
+		uint64_t reserved_2_7:6;
+		uint64_t dcc_enable:1;
+		uint64_t sil_mode:1;
+		uint64_t sequence:3;
+		uint64_t idlepower:3;
+		uint64_t forcewrite:4;
+		uint64_t ecc_adr:1;
+		uint64_t reserved_21_63:43;
+#endif
+	} s;
+	struct cvmx_lmcx_ctl1_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t data_layout:2;
+#else
+		uint64_t data_layout:2;
+		uint64_t reserved_2_63:62;
+#endif
+	} cn30xx;
+	struct cvmx_lmcx_ctl1_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t sil_mode:1;
+		uint64_t dcc_enable:1;
+		uint64_t reserved_2_7:6;
+		uint64_t data_layout:2;
+#else
+		uint64_t data_layout:2;
+		uint64_t reserved_2_7:6;
+		uint64_t dcc_enable:1;
+		uint64_t sil_mode:1;
+		uint64_t reserved_10_63:54;
+#endif
+	} cn50xx;
+	struct cvmx_lmcx_ctl1_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_21_63:43;
+		uint64_t ecc_adr:1;
+		uint64_t forcewrite:4;
+		uint64_t idlepower:3;
+		uint64_t sequence:3;
+		uint64_t sil_mode:1;
+		uint64_t dcc_enable:1;
+		uint64_t reserved_0_7:8;
+#else
+		uint64_t reserved_0_7:8;
+		uint64_t dcc_enable:1;
+		uint64_t sil_mode:1;
+		uint64_t sequence:3;
+		uint64_t idlepower:3;
+		uint64_t forcewrite:4;
+		uint64_t ecc_adr:1;
+		uint64_t reserved_21_63:43;
+#endif
+	} cn52xx;
+	struct cvmx_lmcx_ctl1_cn58xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t sil_mode:1;
+		uint64_t dcc_enable:1;
+		uint64_t reserved_0_7:8;
+#else
+		uint64_t reserved_0_7:8;
+		uint64_t dcc_enable:1;
+		uint64_t sil_mode:1;
+		uint64_t reserved_10_63:54;
+#endif
+	} cn58xx;
+};
+
+union cvmx_lmcx_dclk_cnt {
+	uint64_t u64;
+	struct cvmx_lmcx_dclk_cnt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t dclkcnt:64;
+#else
+		uint64_t dclkcnt:64;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_dclk_cnt_hi {
+	uint64_t u64;
+	struct cvmx_lmcx_dclk_cnt_hi_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t dclkcnt_hi:32;
+#else
+		uint64_t dclkcnt_hi:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_dclk_cnt_lo {
+	uint64_t u64;
+	struct cvmx_lmcx_dclk_cnt_lo_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t dclkcnt_lo:32;
+#else
+		uint64_t dclkcnt_lo:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_dclk_ctl {
+	uint64_t u64;
+	struct cvmx_lmcx_dclk_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t off90_ena:1;
+		uint64_t dclk90_byp:1;
+		uint64_t dclk90_ld:1;
+		uint64_t dclk90_vlu:5;
+#else
+		uint64_t dclk90_vlu:5;
+		uint64_t dclk90_ld:1;
+		uint64_t dclk90_byp:1;
+		uint64_t off90_ena:1;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_ddr2_ctl {
+	uint64_t u64;
+	struct cvmx_lmcx_ddr2_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t bank8:1;
+		uint64_t burst8:1;
+		uint64_t addlat:3;
+		uint64_t pocas:1;
+		uint64_t bwcnt:1;
+		uint64_t twr:3;
+		uint64_t silo_hc:1;
+		uint64_t ddr_eof:4;
+		uint64_t tfaw:5;
+		uint64_t crip_mode:1;
+		uint64_t ddr2t:1;
+		uint64_t odt_ena:1;
+		uint64_t qdll_ena:1;
+		uint64_t dll90_vlu:5;
+		uint64_t dll90_byp:1;
+		uint64_t rdqs:1;
+		uint64_t ddr2:1;
+#else
+		uint64_t ddr2:1;
+		uint64_t rdqs:1;
+		uint64_t dll90_byp:1;
+		uint64_t dll90_vlu:5;
+		uint64_t qdll_ena:1;
+		uint64_t odt_ena:1;
+		uint64_t ddr2t:1;
+		uint64_t crip_mode:1;
+		uint64_t tfaw:5;
+		uint64_t ddr_eof:4;
+		uint64_t silo_hc:1;
+		uint64_t twr:3;
+		uint64_t bwcnt:1;
+		uint64_t pocas:1;
+		uint64_t addlat:3;
+		uint64_t burst8:1;
+		uint64_t bank8:1;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+	struct cvmx_lmcx_ddr2_ctl_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t bank8:1;
+		uint64_t burst8:1;
+		uint64_t addlat:3;
+		uint64_t pocas:1;
+		uint64_t bwcnt:1;
+		uint64_t twr:3;
+		uint64_t silo_hc:1;
+		uint64_t ddr_eof:4;
+		uint64_t tfaw:5;
+		uint64_t crip_mode:1;
+		uint64_t ddr2t:1;
+		uint64_t odt_ena:1;
+		uint64_t qdll_ena:1;
+		uint64_t dll90_vlu:5;
+		uint64_t dll90_byp:1;
+		uint64_t reserved_1_1:1;
+		uint64_t ddr2:1;
+#else
+		uint64_t ddr2:1;
+		uint64_t reserved_1_1:1;
+		uint64_t dll90_byp:1;
+		uint64_t dll90_vlu:5;
+		uint64_t qdll_ena:1;
+		uint64_t odt_ena:1;
+		uint64_t ddr2t:1;
+		uint64_t crip_mode:1;
+		uint64_t tfaw:5;
+		uint64_t ddr_eof:4;
+		uint64_t silo_hc:1;
+		uint64_t twr:3;
+		uint64_t bwcnt:1;
+		uint64_t pocas:1;
+		uint64_t addlat:3;
+		uint64_t burst8:1;
+		uint64_t bank8:1;
+		uint64_t reserved_32_63:32;
+#endif
+	} cn30xx;
+};
+
+union cvmx_lmcx_ddr_pll_ctl {
+	uint64_t u64;
+	struct cvmx_lmcx_ddr_pll_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_27_63:37;
+		uint64_t jtg_test_mode:1;
+		uint64_t dfm_div_reset:1;
+		uint64_t dfm_ps_en:3;
+		uint64_t ddr_div_reset:1;
+		uint64_t ddr_ps_en:3;
+		uint64_t diffamp:4;
+		uint64_t cps:3;
+		uint64_t cpb:3;
+		uint64_t reset_n:1;
+		uint64_t clkf:7;
+#else
+		uint64_t clkf:7;
+		uint64_t reset_n:1;
+		uint64_t cpb:3;
+		uint64_t cps:3;
+		uint64_t diffamp:4;
+		uint64_t ddr_ps_en:3;
+		uint64_t ddr_div_reset:1;
+		uint64_t dfm_ps_en:3;
+		uint64_t dfm_div_reset:1;
+		uint64_t jtg_test_mode:1;
+		uint64_t reserved_27_63:37;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_delay_cfg {
+	uint64_t u64;
+	struct cvmx_lmcx_delay_cfg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_15_63:49;
+		uint64_t dq:5;
+		uint64_t cmd:5;
+		uint64_t clk:5;
+#else
+		uint64_t clk:5;
+		uint64_t cmd:5;
+		uint64_t dq:5;
+		uint64_t reserved_15_63:49;
+#endif
+	} s;
+	struct cvmx_lmcx_delay_cfg_cn38xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_14_63:50;
+		uint64_t dq:4;
+		uint64_t reserved_9_9:1;
+		uint64_t cmd:4;
+		uint64_t reserved_4_4:1;
+		uint64_t clk:4;
+#else
+		uint64_t clk:4;
+		uint64_t reserved_4_4:1;
+		uint64_t cmd:4;
+		uint64_t reserved_9_9:1;
+		uint64_t dq:4;
+		uint64_t reserved_14_63:50;
+#endif
+	} cn38xx;
+};
+
+union cvmx_lmcx_dimmx_params {
+	uint64_t u64;
+	struct cvmx_lmcx_dimmx_params_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t rc15:4;
+		uint64_t rc14:4;
+		uint64_t rc13:4;
+		uint64_t rc12:4;
+		uint64_t rc11:4;
+		uint64_t rc10:4;
+		uint64_t rc9:4;
+		uint64_t rc8:4;
+		uint64_t rc7:4;
+		uint64_t rc6:4;
+		uint64_t rc5:4;
+		uint64_t rc4:4;
+		uint64_t rc3:4;
+		uint64_t rc2:4;
+		uint64_t rc1:4;
+		uint64_t rc0:4;
+#else
+		uint64_t rc0:4;
+		uint64_t rc1:4;
+		uint64_t rc2:4;
+		uint64_t rc3:4;
+		uint64_t rc4:4;
+		uint64_t rc5:4;
+		uint64_t rc6:4;
+		uint64_t rc7:4;
+		uint64_t rc8:4;
+		uint64_t rc9:4;
+		uint64_t rc10:4;
+		uint64_t rc11:4;
+		uint64_t rc12:4;
+		uint64_t rc13:4;
+		uint64_t rc14:4;
+		uint64_t rc15:4;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_dimm_ctl {
+	uint64_t u64;
+	struct cvmx_lmcx_dimm_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_46_63:18;
+		uint64_t parity:1;
+		uint64_t tcws:13;
+		uint64_t dimm1_wmask:16;
+		uint64_t dimm0_wmask:16;
+#else
+		uint64_t dimm0_wmask:16;
+		uint64_t dimm1_wmask:16;
+		uint64_t tcws:13;
+		uint64_t parity:1;
+		uint64_t reserved_46_63:18;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_dll_ctl {
+	uint64_t u64;
+	struct cvmx_lmcx_dll_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t dreset:1;
+		uint64_t dll90_byp:1;
+		uint64_t dll90_ena:1;
+		uint64_t dll90_vlu:5;
+#else
+		uint64_t dll90_vlu:5;
+		uint64_t dll90_ena:1;
+		uint64_t dll90_byp:1;
+		uint64_t dreset:1;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_dll_ctl2 {
+	uint64_t u64;
+	struct cvmx_lmcx_dll_ctl2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t intf_en:1;
+		uint64_t dll_bringup:1;
+		uint64_t dreset:1;
+		uint64_t quad_dll_ena:1;
+		uint64_t byp_sel:4;
+		uint64_t byp_setting:8;
+#else
+		uint64_t byp_setting:8;
+		uint64_t byp_sel:4;
+		uint64_t quad_dll_ena:1;
+		uint64_t dreset:1;
+		uint64_t dll_bringup:1;
+		uint64_t intf_en:1;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+	struct cvmx_lmcx_dll_ctl2_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_15_63:49;
+		uint64_t dll_bringup:1;
+		uint64_t dreset:1;
+		uint64_t quad_dll_ena:1;
+		uint64_t byp_sel:4;
+		uint64_t byp_setting:8;
+#else
+		uint64_t byp_setting:8;
+		uint64_t byp_sel:4;
+		uint64_t quad_dll_ena:1;
+		uint64_t dreset:1;
+		uint64_t dll_bringup:1;
+		uint64_t reserved_15_63:49;
+#endif
+	} cn63xx;
+};
+
+union cvmx_lmcx_dll_ctl3 {
+	uint64_t u64;
+	struct cvmx_lmcx_dll_ctl3_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_41_63:23;
+		uint64_t dclk90_fwd:1;
+		uint64_t ddr_90_dly_byp:1;
+		uint64_t dclk90_recal_dis:1;
+		uint64_t dclk90_byp_sel:1;
+		uint64_t dclk90_byp_setting:8;
+		uint64_t dll_fast:1;
+		uint64_t dll90_setting:8;
+		uint64_t fine_tune_mode:1;
+		uint64_t dll_mode:1;
+		uint64_t dll90_byte_sel:4;
+		uint64_t offset_ena:1;
+		uint64_t load_offset:1;
+		uint64_t mode_sel:2;
+		uint64_t byte_sel:4;
+		uint64_t offset:6;
+#else
+		uint64_t offset:6;
+		uint64_t byte_sel:4;
+		uint64_t mode_sel:2;
+		uint64_t load_offset:1;
+		uint64_t offset_ena:1;
+		uint64_t dll90_byte_sel:4;
+		uint64_t dll_mode:1;
+		uint64_t fine_tune_mode:1;
+		uint64_t dll90_setting:8;
+		uint64_t dll_fast:1;
+		uint64_t dclk90_byp_setting:8;
+		uint64_t dclk90_byp_sel:1;
+		uint64_t dclk90_recal_dis:1;
+		uint64_t ddr_90_dly_byp:1;
+		uint64_t dclk90_fwd:1;
+		uint64_t reserved_41_63:23;
+#endif
+	} s;
+	struct cvmx_lmcx_dll_ctl3_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t dll_fast:1;
+		uint64_t dll90_setting:8;
+		uint64_t fine_tune_mode:1;
+		uint64_t dll_mode:1;
+		uint64_t dll90_byte_sel:4;
+		uint64_t offset_ena:1;
+		uint64_t load_offset:1;
+		uint64_t mode_sel:2;
+		uint64_t byte_sel:4;
+		uint64_t offset:6;
+#else
+		uint64_t offset:6;
+		uint64_t byte_sel:4;
+		uint64_t mode_sel:2;
+		uint64_t load_offset:1;
+		uint64_t offset_ena:1;
+		uint64_t dll90_byte_sel:4;
+		uint64_t dll_mode:1;
+		uint64_t fine_tune_mode:1;
+		uint64_t dll90_setting:8;
+		uint64_t dll_fast:1;
+		uint64_t reserved_29_63:35;
+#endif
+	} cn63xx;
+};
+
+union cvmx_lmcx_dual_memcfg {
+	uint64_t u64;
+	struct cvmx_lmcx_dual_memcfg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t bank8:1;
+		uint64_t row_lsb:3;
+		uint64_t reserved_8_15:8;
+		uint64_t cs_mask:8;
+#else
+		uint64_t cs_mask:8;
+		uint64_t reserved_8_15:8;
+		uint64_t row_lsb:3;
+		uint64_t bank8:1;
+		uint64_t reserved_20_63:44;
+#endif
+	} s;
+	struct cvmx_lmcx_dual_memcfg_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_19_63:45;
+		uint64_t row_lsb:3;
+		uint64_t reserved_8_15:8;
+		uint64_t cs_mask:8;
+#else
+		uint64_t cs_mask:8;
+		uint64_t reserved_8_15:8;
+		uint64_t row_lsb:3;
+		uint64_t reserved_19_63:45;
+#endif
+	} cn61xx;
+};
+
+union cvmx_lmcx_ecc_synd {
+	uint64_t u64;
+	struct cvmx_lmcx_ecc_synd_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t mrdsyn3:8;
+		uint64_t mrdsyn2:8;
+		uint64_t mrdsyn1:8;
+		uint64_t mrdsyn0:8;
+#else
+		uint64_t mrdsyn0:8;
+		uint64_t mrdsyn1:8;
+		uint64_t mrdsyn2:8;
+		uint64_t mrdsyn3:8;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_fadr {
+	uint64_t u64;
+	struct cvmx_lmcx_fadr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_0_63:64;
+#else
+		uint64_t reserved_0_63:64;
+#endif
+	} s;
+	struct cvmx_lmcx_fadr_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t fdimm:2;
+		uint64_t fbunk:1;
+		uint64_t fbank:3;
+		uint64_t frow:14;
+		uint64_t fcol:12;
+#else
+		uint64_t fcol:12;
+		uint64_t frow:14;
+		uint64_t fbank:3;
+		uint64_t fbunk:1;
+		uint64_t fdimm:2;
+		uint64_t reserved_32_63:32;
+#endif
+	} cn30xx;
+	struct cvmx_lmcx_fadr_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_36_63:28;
+		uint64_t fdimm:2;
+		uint64_t fbunk:1;
+		uint64_t fbank:3;
+		uint64_t frow:16;
+		uint64_t fcol:14;
+#else
+		uint64_t fcol:14;
+		uint64_t frow:16;
+		uint64_t fbank:3;
+		uint64_t fbunk:1;
+		uint64_t fdimm:2;
+		uint64_t reserved_36_63:28;
+#endif
+	} cn61xx;
+};
+
+union cvmx_lmcx_ifb_cnt {
+	uint64_t u64;
+	struct cvmx_lmcx_ifb_cnt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t ifbcnt:64;
+#else
+		uint64_t ifbcnt:64;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_ifb_cnt_hi {
+	uint64_t u64;
+	struct cvmx_lmcx_ifb_cnt_hi_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t ifbcnt_hi:32;
+#else
+		uint64_t ifbcnt_hi:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_ifb_cnt_lo {
+	uint64_t u64;
+	struct cvmx_lmcx_ifb_cnt_lo_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t ifbcnt_lo:32;
+#else
+		uint64_t ifbcnt_lo:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_int {
+	uint64_t u64;
+	struct cvmx_lmcx_int_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_9_63:55;
+		uint64_t ded_err:4;
+		uint64_t sec_err:4;
+		uint64_t nxm_wr_err:1;
+#else
+		uint64_t nxm_wr_err:1;
+		uint64_t sec_err:4;
+		uint64_t ded_err:4;
+		uint64_t reserved_9_63:55;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_int_en {
+	uint64_t u64;
+	struct cvmx_lmcx_int_en_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_3_63:61;
+		uint64_t intr_ded_ena:1;
+		uint64_t intr_sec_ena:1;
+		uint64_t intr_nxm_wr_ena:1;
+#else
+		uint64_t intr_nxm_wr_ena:1;
+		uint64_t intr_sec_ena:1;
+		uint64_t intr_ded_ena:1;
+		uint64_t reserved_3_63:61;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_mem_cfg0 {
+	uint64_t u64;
+	struct cvmx_lmcx_mem_cfg0_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t reset:1;
+		uint64_t silo_qc:1;
+		uint64_t bunk_ena:1;
+		uint64_t ded_err:4;
+		uint64_t sec_err:4;
+		uint64_t intr_ded_ena:1;
+		uint64_t intr_sec_ena:1;
+		uint64_t tcl:4;
+		uint64_t ref_int:6;
+		uint64_t pbank_lsb:4;
+		uint64_t row_lsb:3;
+		uint64_t ecc_ena:1;
+		uint64_t init_start:1;
+#else
+		uint64_t init_start:1;
+		uint64_t ecc_ena:1;
+		uint64_t row_lsb:3;
+		uint64_t pbank_lsb:4;
+		uint64_t ref_int:6;
+		uint64_t tcl:4;
+		uint64_t intr_sec_ena:1;
+		uint64_t intr_ded_ena:1;
+		uint64_t sec_err:4;
+		uint64_t ded_err:4;
+		uint64_t bunk_ena:1;
+		uint64_t silo_qc:1;
+		uint64_t reset:1;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_mem_cfg1 {
+	uint64_t u64;
+	struct cvmx_lmcx_mem_cfg1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t comp_bypass:1;
+		uint64_t trrd:3;
+		uint64_t caslat:3;
+		uint64_t tmrd:3;
+		uint64_t trfc:5;
+		uint64_t trp:4;
+		uint64_t twtr:4;
+		uint64_t trcd:4;
+		uint64_t tras:5;
+#else
+		uint64_t tras:5;
+		uint64_t trcd:4;
+		uint64_t twtr:4;
+		uint64_t trp:4;
+		uint64_t trfc:5;
+		uint64_t tmrd:3;
+		uint64_t caslat:3;
+		uint64_t trrd:3;
+		uint64_t comp_bypass:1;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+	struct cvmx_lmcx_mem_cfg1_cn38xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_31_63:33;
+		uint64_t trrd:3;
+		uint64_t caslat:3;
+		uint64_t tmrd:3;
+		uint64_t trfc:5;
+		uint64_t trp:4;
+		uint64_t twtr:4;
+		uint64_t trcd:4;
+		uint64_t tras:5;
+#else
+		uint64_t tras:5;
+		uint64_t trcd:4;
+		uint64_t twtr:4;
+		uint64_t trp:4;
+		uint64_t trfc:5;
+		uint64_t tmrd:3;
+		uint64_t caslat:3;
+		uint64_t trrd:3;
+		uint64_t reserved_31_63:33;
+#endif
+	} cn38xx;
+};
+
+union cvmx_lmcx_modereg_params0 {
+	uint64_t u64;
+	struct cvmx_lmcx_modereg_params0_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_25_63:39;
+		uint64_t ppd:1;
+		uint64_t wrp:3;
+		uint64_t dllr:1;
+		uint64_t tm:1;
+		uint64_t rbt:1;
+		uint64_t cl:4;
+		uint64_t bl:2;
+		uint64_t qoff:1;
+		uint64_t tdqs:1;
+		uint64_t wlev:1;
+		uint64_t al:2;
+		uint64_t dll:1;
+		uint64_t mpr:1;
+		uint64_t mprloc:2;
+		uint64_t cwl:3;
+#else
+		uint64_t cwl:3;
+		uint64_t mprloc:2;
+		uint64_t mpr:1;
+		uint64_t dll:1;
+		uint64_t al:2;
+		uint64_t wlev:1;
+		uint64_t tdqs:1;
+		uint64_t qoff:1;
+		uint64_t bl:2;
+		uint64_t cl:4;
+		uint64_t rbt:1;
+		uint64_t tm:1;
+		uint64_t dllr:1;
+		uint64_t wrp:3;
+		uint64_t ppd:1;
+		uint64_t reserved_25_63:39;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_modereg_params1 {
+	uint64_t u64;
+	struct cvmx_lmcx_modereg_params1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t rtt_nom_11:3;
+		uint64_t dic_11:2;
+		uint64_t rtt_wr_11:2;
+		uint64_t srt_11:1;
+		uint64_t asr_11:1;
+		uint64_t pasr_11:3;
+		uint64_t rtt_nom_10:3;
+		uint64_t dic_10:2;
+		uint64_t rtt_wr_10:2;
+		uint64_t srt_10:1;
+		uint64_t asr_10:1;
+		uint64_t pasr_10:3;
+		uint64_t rtt_nom_01:3;
+		uint64_t dic_01:2;
+		uint64_t rtt_wr_01:2;
+		uint64_t srt_01:1;
+		uint64_t asr_01:1;
+		uint64_t pasr_01:3;
+		uint64_t rtt_nom_00:3;
+		uint64_t dic_00:2;
+		uint64_t rtt_wr_00:2;
+		uint64_t srt_00:1;
+		uint64_t asr_00:1;
+		uint64_t pasr_00:3;
+#else
+		uint64_t pasr_00:3;
+		uint64_t asr_00:1;
+		uint64_t srt_00:1;
+		uint64_t rtt_wr_00:2;
+		uint64_t dic_00:2;
+		uint64_t rtt_nom_00:3;
+		uint64_t pasr_01:3;
+		uint64_t asr_01:1;
+		uint64_t srt_01:1;
+		uint64_t rtt_wr_01:2;
+		uint64_t dic_01:2;
+		uint64_t rtt_nom_01:3;
+		uint64_t pasr_10:3;
+		uint64_t asr_10:1;
+		uint64_t srt_10:1;
+		uint64_t rtt_wr_10:2;
+		uint64_t dic_10:2;
+		uint64_t rtt_nom_10:3;
+		uint64_t pasr_11:3;
+		uint64_t asr_11:1;
+		uint64_t srt_11:1;
+		uint64_t rtt_wr_11:2;
+		uint64_t dic_11:2;
+		uint64_t rtt_nom_11:3;
+		uint64_t reserved_48_63:16;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_nxm {
+	uint64_t u64;
+	struct cvmx_lmcx_nxm_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_40_63:24;
+		uint64_t mem_msb_d3_r1:4;
+		uint64_t mem_msb_d3_r0:4;
+		uint64_t mem_msb_d2_r1:4;
+		uint64_t mem_msb_d2_r0:4;
+		uint64_t mem_msb_d1_r1:4;
+		uint64_t mem_msb_d1_r0:4;
+		uint64_t mem_msb_d0_r1:4;
+		uint64_t mem_msb_d0_r0:4;
+		uint64_t cs_mask:8;
+#else
+		uint64_t cs_mask:8;
+		uint64_t mem_msb_d0_r0:4;
+		uint64_t mem_msb_d0_r1:4;
+		uint64_t mem_msb_d1_r0:4;
+		uint64_t mem_msb_d1_r1:4;
+		uint64_t mem_msb_d2_r0:4;
+		uint64_t mem_msb_d2_r1:4;
+		uint64_t mem_msb_d3_r0:4;
+		uint64_t mem_msb_d3_r1:4;
+		uint64_t reserved_40_63:24;
+#endif
+	} s;
+	struct cvmx_lmcx_nxm_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t cs_mask:8;
+#else
+		uint64_t cs_mask:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} cn52xx;
+};
+
+union cvmx_lmcx_ops_cnt {
+	uint64_t u64;
+	struct cvmx_lmcx_ops_cnt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t opscnt:64;
+#else
+		uint64_t opscnt:64;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_ops_cnt_hi {
+	uint64_t u64;
+	struct cvmx_lmcx_ops_cnt_hi_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t opscnt_hi:32;
+#else
+		uint64_t opscnt_hi:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_ops_cnt_lo {
+	uint64_t u64;
+	struct cvmx_lmcx_ops_cnt_lo_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t opscnt_lo:32;
+#else
+		uint64_t opscnt_lo:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_phy_ctl {
+	uint64_t u64;
+	struct cvmx_lmcx_phy_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_15_63:49;
+		uint64_t rx_always_on:1;
+		uint64_t lv_mode:1;
+		uint64_t ck_tune1:1;
+		uint64_t ck_dlyout1:4;
+		uint64_t ck_tune0:1;
+		uint64_t ck_dlyout0:4;
+		uint64_t loopback:1;
+		uint64_t loopback_pos:1;
+		uint64_t ts_stagger:1;
+#else
+		uint64_t ts_stagger:1;
+		uint64_t loopback_pos:1;
+		uint64_t loopback:1;
+		uint64_t ck_dlyout0:4;
+		uint64_t ck_tune0:1;
+		uint64_t ck_dlyout1:4;
+		uint64_t ck_tune1:1;
+		uint64_t lv_mode:1;
+		uint64_t rx_always_on:1;
+		uint64_t reserved_15_63:49;
+#endif
+	} s;
+	struct cvmx_lmcx_phy_ctl_cn63xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_14_63:50;
+		uint64_t lv_mode:1;
+		uint64_t ck_tune1:1;
+		uint64_t ck_dlyout1:4;
+		uint64_t ck_tune0:1;
+		uint64_t ck_dlyout0:4;
+		uint64_t loopback:1;
+		uint64_t loopback_pos:1;
+		uint64_t ts_stagger:1;
+#else
+		uint64_t ts_stagger:1;
+		uint64_t loopback_pos:1;
+		uint64_t loopback:1;
+		uint64_t ck_dlyout0:4;
+		uint64_t ck_tune0:1;
+		uint64_t ck_dlyout1:4;
+		uint64_t ck_tune1:1;
+		uint64_t lv_mode:1;
+		uint64_t reserved_14_63:50;
+#endif
+	} cn63xxp1;
+};
+
+union cvmx_lmcx_pll_bwctl {
+	uint64_t u64;
+	struct cvmx_lmcx_pll_bwctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_5_63:59;
+		uint64_t bwupd:1;
+		uint64_t bwctl:4;
+#else
+		uint64_t bwctl:4;
+		uint64_t bwupd:1;
+		uint64_t reserved_5_63:59;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_pll_ctl {
+	uint64_t u64;
+	struct cvmx_lmcx_pll_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_30_63:34;
+		uint64_t bypass:1;
+		uint64_t fasten_n:1;
+		uint64_t div_reset:1;
+		uint64_t reset_n:1;
+		uint64_t clkf:12;
+		uint64_t clkr:6;
+		uint64_t reserved_6_7:2;
+		uint64_t en16:1;
+		uint64_t en12:1;
+		uint64_t en8:1;
+		uint64_t en6:1;
+		uint64_t en4:1;
+		uint64_t en2:1;
+#else
+		uint64_t en2:1;
+		uint64_t en4:1;
+		uint64_t en6:1;
+		uint64_t en8:1;
+		uint64_t en12:1;
+		uint64_t en16:1;
+		uint64_t reserved_6_7:2;
+		uint64_t clkr:6;
+		uint64_t clkf:12;
+		uint64_t reset_n:1;
+		uint64_t div_reset:1;
+		uint64_t fasten_n:1;
+		uint64_t bypass:1;
+		uint64_t reserved_30_63:34;
+#endif
+	} s;
+	struct cvmx_lmcx_pll_ctl_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t fasten_n:1;
+		uint64_t div_reset:1;
+		uint64_t reset_n:1;
+		uint64_t clkf:12;
+		uint64_t clkr:6;
+		uint64_t reserved_6_7:2;
+		uint64_t en16:1;
+		uint64_t en12:1;
+		uint64_t en8:1;
+		uint64_t en6:1;
+		uint64_t en4:1;
+		uint64_t en2:1;
+#else
+		uint64_t en2:1;
+		uint64_t en4:1;
+		uint64_t en6:1;
+		uint64_t en8:1;
+		uint64_t en12:1;
+		uint64_t en16:1;
+		uint64_t reserved_6_7:2;
+		uint64_t clkr:6;
+		uint64_t clkf:12;
+		uint64_t reset_n:1;
+		uint64_t div_reset:1;
+		uint64_t fasten_n:1;
+		uint64_t reserved_29_63:35;
+#endif
+	} cn50xx;
+	struct cvmx_lmcx_pll_ctl_cn56xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_28_63:36;
+		uint64_t div_reset:1;
+		uint64_t reset_n:1;
+		uint64_t clkf:12;
+		uint64_t clkr:6;
+		uint64_t reserved_6_7:2;
+		uint64_t en16:1;
+		uint64_t en12:1;
+		uint64_t en8:1;
+		uint64_t en6:1;
+		uint64_t en4:1;
+		uint64_t en2:1;
+#else
+		uint64_t en2:1;
+		uint64_t en4:1;
+		uint64_t en6:1;
+		uint64_t en8:1;
+		uint64_t en12:1;
+		uint64_t en16:1;
+		uint64_t reserved_6_7:2;
+		uint64_t clkr:6;
+		uint64_t clkf:12;
+		uint64_t reset_n:1;
+		uint64_t div_reset:1;
+		uint64_t reserved_28_63:36;
+#endif
+	} cn56xxp1;
+};
+
+union cvmx_lmcx_pll_status {
+	uint64_t u64;
+	struct cvmx_lmcx_pll_status_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t ddr__nctl:5;
+		uint64_t ddr__pctl:5;
+		uint64_t reserved_2_21:20;
+		uint64_t rfslip:1;
+		uint64_t fbslip:1;
+#else
+		uint64_t fbslip:1;
+		uint64_t rfslip:1;
+		uint64_t reserved_2_21:20;
+		uint64_t ddr__pctl:5;
+		uint64_t ddr__nctl:5;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+	struct cvmx_lmcx_pll_status_cn58xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t rfslip:1;
+		uint64_t fbslip:1;
+#else
+		uint64_t fbslip:1;
+		uint64_t rfslip:1;
+		uint64_t reserved_2_63:62;
+#endif
+	} cn58xxp1;
+};
+
+union cvmx_lmcx_read_level_ctl {
+	uint64_t u64;
+	struct cvmx_lmcx_read_level_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_44_63:20;
+		uint64_t rankmask:4;
+		uint64_t pattern:8;
+		uint64_t row:16;
+		uint64_t col:12;
+		uint64_t reserved_3_3:1;
+		uint64_t bnk:3;
+#else
+		uint64_t bnk:3;
+		uint64_t reserved_3_3:1;
+		uint64_t col:12;
+		uint64_t row:16;
+		uint64_t pattern:8;
+		uint64_t rankmask:4;
+		uint64_t reserved_44_63:20;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_read_level_dbg {
+	uint64_t u64;
+	struct cvmx_lmcx_read_level_dbg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t bitmask:16;
+		uint64_t reserved_4_15:12;
+		uint64_t byte:4;
+#else
+		uint64_t byte:4;
+		uint64_t reserved_4_15:12;
+		uint64_t bitmask:16;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_read_level_rankx {
+	uint64_t u64;
+	struct cvmx_lmcx_read_level_rankx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_38_63:26;
+		uint64_t status:2;
+		uint64_t byte8:4;
+		uint64_t byte7:4;
+		uint64_t byte6:4;
+		uint64_t byte5:4;
+		uint64_t byte4:4;
+		uint64_t byte3:4;
+		uint64_t byte2:4;
+		uint64_t byte1:4;
+		uint64_t byte0:4;
+#else
+		uint64_t byte0:4;
+		uint64_t byte1:4;
+		uint64_t byte2:4;
+		uint64_t byte3:4;
+		uint64_t byte4:4;
+		uint64_t byte5:4;
+		uint64_t byte6:4;
+		uint64_t byte7:4;
+		uint64_t byte8:4;
+		uint64_t status:2;
+		uint64_t reserved_38_63:26;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_reset_ctl {
+	uint64_t u64;
+	struct cvmx_lmcx_reset_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t ddr3psv:1;
+		uint64_t ddr3psoft:1;
+		uint64_t ddr3pwarm:1;
+		uint64_t ddr3rst:1;
+#else
+		uint64_t ddr3rst:1;
+		uint64_t ddr3pwarm:1;
+		uint64_t ddr3psoft:1;
+		uint64_t ddr3psv:1;
+		uint64_t reserved_4_63:60;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_rlevel_ctl {
+	uint64_t u64;
+	struct cvmx_lmcx_rlevel_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_22_63:42;
+		uint64_t delay_unload_3:1;
+		uint64_t delay_unload_2:1;
+		uint64_t delay_unload_1:1;
+		uint64_t delay_unload_0:1;
+		uint64_t bitmask:8;
+		uint64_t or_dis:1;
+		uint64_t offset_en:1;
+		uint64_t offset:4;
+		uint64_t byte:4;
+#else
+		uint64_t byte:4;
+		uint64_t offset:4;
+		uint64_t offset_en:1;
+		uint64_t or_dis:1;
+		uint64_t bitmask:8;
+		uint64_t delay_unload_0:1;
+		uint64_t delay_unload_1:1;
+		uint64_t delay_unload_2:1;
+		uint64_t delay_unload_3:1;
+		uint64_t reserved_22_63:42;
+#endif
+	} s;
+	struct cvmx_lmcx_rlevel_ctl_cn63xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_9_63:55;
+		uint64_t offset_en:1;
+		uint64_t offset:4;
+		uint64_t byte:4;
+#else
+		uint64_t byte:4;
+		uint64_t offset:4;
+		uint64_t offset_en:1;
+		uint64_t reserved_9_63:55;
+#endif
+	} cn63xxp1;
+};
+
+union cvmx_lmcx_rlevel_dbg {
+	uint64_t u64;
+	struct cvmx_lmcx_rlevel_dbg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t bitmask:64;
+#else
+		uint64_t bitmask:64;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_rlevel_rankx {
+	uint64_t u64;
+	struct cvmx_lmcx_rlevel_rankx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_56_63:8;
+		uint64_t status:2;
+		uint64_t byte8:6;
+		uint64_t byte7:6;
+		uint64_t byte6:6;
+		uint64_t byte5:6;
+		uint64_t byte4:6;
+		uint64_t byte3:6;
+		uint64_t byte2:6;
+		uint64_t byte1:6;
+		uint64_t byte0:6;
+#else
+		uint64_t byte0:6;
+		uint64_t byte1:6;
+		uint64_t byte2:6;
+		uint64_t byte3:6;
+		uint64_t byte4:6;
+		uint64_t byte5:6;
+		uint64_t byte6:6;
+		uint64_t byte7:6;
+		uint64_t byte8:6;
+		uint64_t status:2;
+		uint64_t reserved_56_63:8;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_rodt_comp_ctl {
+	uint64_t u64;
+	struct cvmx_lmcx_rodt_comp_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_17_63:47;
+		uint64_t enable:1;
+		uint64_t reserved_12_15:4;
+		uint64_t nctl:4;
+		uint64_t reserved_5_7:3;
+		uint64_t pctl:5;
+#else
+		uint64_t pctl:5;
+		uint64_t reserved_5_7:3;
+		uint64_t nctl:4;
+		uint64_t reserved_12_15:4;
+		uint64_t enable:1;
+		uint64_t reserved_17_63:47;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_rodt_ctl {
+	uint64_t u64;
+	struct cvmx_lmcx_rodt_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t rodt_hi3:4;
+		uint64_t rodt_hi2:4;
+		uint64_t rodt_hi1:4;
+		uint64_t rodt_hi0:4;
+		uint64_t rodt_lo3:4;
+		uint64_t rodt_lo2:4;
+		uint64_t rodt_lo1:4;
+		uint64_t rodt_lo0:4;
+#else
+		uint64_t rodt_lo0:4;
+		uint64_t rodt_lo1:4;
+		uint64_t rodt_lo2:4;
+		uint64_t rodt_lo3:4;
+		uint64_t rodt_hi0:4;
+		uint64_t rodt_hi1:4;
+		uint64_t rodt_hi2:4;
+		uint64_t rodt_hi3:4;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_rodt_mask {
+	uint64_t u64;
+	struct cvmx_lmcx_rodt_mask_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t rodt_d3_r1:8;
+		uint64_t rodt_d3_r0:8;
+		uint64_t rodt_d2_r1:8;
+		uint64_t rodt_d2_r0:8;
+		uint64_t rodt_d1_r1:8;
+		uint64_t rodt_d1_r0:8;
+		uint64_t rodt_d0_r1:8;
+		uint64_t rodt_d0_r0:8;
+#else
+		uint64_t rodt_d0_r0:8;
+		uint64_t rodt_d0_r1:8;
+		uint64_t rodt_d1_r0:8;
+		uint64_t rodt_d1_r1:8;
+		uint64_t rodt_d2_r0:8;
+		uint64_t rodt_d2_r1:8;
+		uint64_t rodt_d3_r0:8;
+		uint64_t rodt_d3_r1:8;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_scramble_cfg0 {
+	uint64_t u64;
+	struct cvmx_lmcx_scramble_cfg0_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t key:64;
+#else
+		uint64_t key:64;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_scramble_cfg1 {
+	uint64_t u64;
+	struct cvmx_lmcx_scramble_cfg1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t key:64;
+#else
+		uint64_t key:64;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_scrambled_fadr {
+	uint64_t u64;
+	struct cvmx_lmcx_scrambled_fadr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_36_63:28;
+		uint64_t fdimm:2;
+		uint64_t fbunk:1;
+		uint64_t fbank:3;
+		uint64_t frow:16;
+		uint64_t fcol:14;
+#else
+		uint64_t fcol:14;
+		uint64_t frow:16;
+		uint64_t fbank:3;
+		uint64_t fbunk:1;
+		uint64_t fdimm:2;
+		uint64_t reserved_36_63:28;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_slot_ctl0 {
+	uint64_t u64;
+	struct cvmx_lmcx_slot_ctl0_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_24_63:40;
+		uint64_t w2w_init:6;
+		uint64_t w2r_init:6;
+		uint64_t r2w_init:6;
+		uint64_t r2r_init:6;
+#else
+		uint64_t r2r_init:6;
+		uint64_t r2w_init:6;
+		uint64_t w2r_init:6;
+		uint64_t w2w_init:6;
+		uint64_t reserved_24_63:40;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_slot_ctl1 {
+	uint64_t u64;
+	struct cvmx_lmcx_slot_ctl1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_24_63:40;
+		uint64_t w2w_xrank_init:6;
+		uint64_t w2r_xrank_init:6;
+		uint64_t r2w_xrank_init:6;
+		uint64_t r2r_xrank_init:6;
+#else
+		uint64_t r2r_xrank_init:6;
+		uint64_t r2w_xrank_init:6;
+		uint64_t w2r_xrank_init:6;
+		uint64_t w2w_xrank_init:6;
+		uint64_t reserved_24_63:40;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_slot_ctl2 {
+	uint64_t u64;
+	struct cvmx_lmcx_slot_ctl2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_24_63:40;
+		uint64_t w2w_xdimm_init:6;
+		uint64_t w2r_xdimm_init:6;
+		uint64_t r2w_xdimm_init:6;
+		uint64_t r2r_xdimm_init:6;
+#else
+		uint64_t r2r_xdimm_init:6;
+		uint64_t r2w_xdimm_init:6;
+		uint64_t w2r_xdimm_init:6;
+		uint64_t w2w_xdimm_init:6;
+		uint64_t reserved_24_63:40;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_timing_params0 {
+	uint64_t u64;
+	struct cvmx_lmcx_timing_params0_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_47_63:17;
+		uint64_t trp_ext:1;
+		uint64_t tcksre:4;
+		uint64_t trp:4;
+		uint64_t tzqinit:4;
+		uint64_t tdllk:4;
+		uint64_t tmod:4;
+		uint64_t tmrd:4;
+		uint64_t txpr:4;
+		uint64_t tcke:4;
+		uint64_t tzqcs:4;
+		uint64_t tckeon:10;
+#else
+		uint64_t tckeon:10;
+		uint64_t tzqcs:4;
+		uint64_t tcke:4;
+		uint64_t txpr:4;
+		uint64_t tmrd:4;
+		uint64_t tmod:4;
+		uint64_t tdllk:4;
+		uint64_t tzqinit:4;
+		uint64_t trp:4;
+		uint64_t tcksre:4;
+		uint64_t trp_ext:1;
+		uint64_t reserved_47_63:17;
+#endif
+	} s;
+	struct cvmx_lmcx_timing_params0_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_47_63:17;
+		uint64_t trp_ext:1;
+		uint64_t tcksre:4;
+		uint64_t trp:4;
+		uint64_t tzqinit:4;
+		uint64_t tdllk:4;
+		uint64_t tmod:4;
+		uint64_t tmrd:4;
+		uint64_t txpr:4;
+		uint64_t tcke:4;
+		uint64_t tzqcs:4;
+		uint64_t reserved_0_9:10;
+#else
+		uint64_t reserved_0_9:10;
+		uint64_t tzqcs:4;
+		uint64_t tcke:4;
+		uint64_t txpr:4;
+		uint64_t tmrd:4;
+		uint64_t tmod:4;
+		uint64_t tdllk:4;
+		uint64_t tzqinit:4;
+		uint64_t trp:4;
+		uint64_t tcksre:4;
+		uint64_t trp_ext:1;
+		uint64_t reserved_47_63:17;
+#endif
+	} cn61xx;
+	struct cvmx_lmcx_timing_params0_cn63xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_46_63:18;
+		uint64_t tcksre:4;
+		uint64_t trp:4;
+		uint64_t tzqinit:4;
+		uint64_t tdllk:4;
+		uint64_t tmod:4;
+		uint64_t tmrd:4;
+		uint64_t txpr:4;
+		uint64_t tcke:4;
+		uint64_t tzqcs:4;
+		uint64_t tckeon:10;
+#else
+		uint64_t tckeon:10;
+		uint64_t tzqcs:4;
+		uint64_t tcke:4;
+		uint64_t txpr:4;
+		uint64_t tmrd:4;
+		uint64_t tmod:4;
+		uint64_t tdllk:4;
+		uint64_t tzqinit:4;
+		uint64_t trp:4;
+		uint64_t tcksre:4;
+		uint64_t reserved_46_63:18;
+#endif
+	} cn63xxp1;
+};
+
+union cvmx_lmcx_timing_params1 {
+	uint64_t u64;
+	struct cvmx_lmcx_timing_params1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_47_63:17;
+		uint64_t tras_ext:1;
+		uint64_t txpdll:5;
+		uint64_t tfaw:5;
+		uint64_t twldqsen:4;
+		uint64_t twlmrd:4;
+		uint64_t txp:3;
+		uint64_t trrd:3;
+		uint64_t trfc:5;
+		uint64_t twtr:4;
+		uint64_t trcd:4;
+		uint64_t tras:5;
+		uint64_t tmprr:4;
+#else
+		uint64_t tmprr:4;
+		uint64_t tras:5;
+		uint64_t trcd:4;
+		uint64_t twtr:4;
+		uint64_t trfc:5;
+		uint64_t trrd:3;
+		uint64_t txp:3;
+		uint64_t twlmrd:4;
+		uint64_t twldqsen:4;
+		uint64_t tfaw:5;
+		uint64_t txpdll:5;
+		uint64_t tras_ext:1;
+		uint64_t reserved_47_63:17;
+#endif
+	} s;
+	struct cvmx_lmcx_timing_params1_cn63xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_46_63:18;
+		uint64_t txpdll:5;
+		uint64_t tfaw:5;
+		uint64_t twldqsen:4;
+		uint64_t twlmrd:4;
+		uint64_t txp:3;
+		uint64_t trrd:3;
+		uint64_t trfc:5;
+		uint64_t twtr:4;
+		uint64_t trcd:4;
+		uint64_t tras:5;
+		uint64_t tmprr:4;
+#else
+		uint64_t tmprr:4;
+		uint64_t tras:5;
+		uint64_t trcd:4;
+		uint64_t twtr:4;
+		uint64_t trfc:5;
+		uint64_t trrd:3;
+		uint64_t txp:3;
+		uint64_t twlmrd:4;
+		uint64_t twldqsen:4;
+		uint64_t tfaw:5;
+		uint64_t txpdll:5;
+		uint64_t reserved_46_63:18;
+#endif
+	} cn63xxp1;
+};
+
+union cvmx_lmcx_tro_ctl {
+	uint64_t u64;
+	struct cvmx_lmcx_tro_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_33_63:31;
+		uint64_t rclk_cnt:32;
+		uint64_t treset:1;
+#else
+		uint64_t treset:1;
+		uint64_t rclk_cnt:32;
+		uint64_t reserved_33_63:31;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_tro_stat {
+	uint64_t u64;
+	struct cvmx_lmcx_tro_stat_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t ring_cnt:32;
+#else
+		uint64_t ring_cnt:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_wlevel_ctl {
+	uint64_t u64;
+	struct cvmx_lmcx_wlevel_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_22_63:42;
+		uint64_t rtt_nom:3;
+		uint64_t bitmask:8;
+		uint64_t or_dis:1;
+		uint64_t sset:1;
+		uint64_t lanemask:9;
+#else
+		uint64_t lanemask:9;
+		uint64_t sset:1;
+		uint64_t or_dis:1;
+		uint64_t bitmask:8;
+		uint64_t rtt_nom:3;
+		uint64_t reserved_22_63:42;
+#endif
+	} s;
+	struct cvmx_lmcx_wlevel_ctl_cn63xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t sset:1;
+		uint64_t lanemask:9;
+#else
+		uint64_t lanemask:9;
+		uint64_t sset:1;
+		uint64_t reserved_10_63:54;
+#endif
+	} cn63xxp1;
+};
+
+union cvmx_lmcx_wlevel_dbg {
+	uint64_t u64;
+	struct cvmx_lmcx_wlevel_dbg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t bitmask:8;
+		uint64_t byte:4;
+#else
+		uint64_t byte:4;
+		uint64_t bitmask:8;
+		uint64_t reserved_12_63:52;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_wlevel_rankx {
+	uint64_t u64;
+	struct cvmx_lmcx_wlevel_rankx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_47_63:17;
+		uint64_t status:2;
+		uint64_t byte8:5;
+		uint64_t byte7:5;
+		uint64_t byte6:5;
+		uint64_t byte5:5;
+		uint64_t byte4:5;
+		uint64_t byte3:5;
+		uint64_t byte2:5;
+		uint64_t byte1:5;
+		uint64_t byte0:5;
+#else
+		uint64_t byte0:5;
+		uint64_t byte1:5;
+		uint64_t byte2:5;
+		uint64_t byte3:5;
+		uint64_t byte4:5;
+		uint64_t byte5:5;
+		uint64_t byte6:5;
+		uint64_t byte7:5;
+		uint64_t byte8:5;
+		uint64_t status:2;
+		uint64_t reserved_47_63:17;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_wodt_ctl0 {
+	uint64_t u64;
+	struct cvmx_lmcx_wodt_ctl0_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_0_63:64;
+#else
+		uint64_t reserved_0_63:64;
+#endif
+	} s;
+	struct cvmx_lmcx_wodt_ctl0_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t wodt_d1_r1:8;
+		uint64_t wodt_d1_r0:8;
+		uint64_t wodt_d0_r1:8;
+		uint64_t wodt_d0_r0:8;
+#else
+		uint64_t wodt_d0_r0:8;
+		uint64_t wodt_d0_r1:8;
+		uint64_t wodt_d1_r0:8;
+		uint64_t wodt_d1_r1:8;
+		uint64_t reserved_32_63:32;
+#endif
+	} cn30xx;
+	struct cvmx_lmcx_wodt_ctl0_cn38xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t wodt_hi3:4;
+		uint64_t wodt_hi2:4;
+		uint64_t wodt_hi1:4;
+		uint64_t wodt_hi0:4;
+		uint64_t wodt_lo3:4;
+		uint64_t wodt_lo2:4;
+		uint64_t wodt_lo1:4;
+		uint64_t wodt_lo0:4;
+#else
+		uint64_t wodt_lo0:4;
+		uint64_t wodt_lo1:4;
+		uint64_t wodt_lo2:4;
+		uint64_t wodt_lo3:4;
+		uint64_t wodt_hi0:4;
+		uint64_t wodt_hi1:4;
+		uint64_t wodt_hi2:4;
+		uint64_t wodt_hi3:4;
+		uint64_t reserved_32_63:32;
+#endif
+	} cn38xx;
+};
+
+union cvmx_lmcx_wodt_ctl1 {
+	uint64_t u64;
+	struct cvmx_lmcx_wodt_ctl1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t wodt_d3_r1:8;
+		uint64_t wodt_d3_r0:8;
+		uint64_t wodt_d2_r1:8;
+		uint64_t wodt_d2_r0:8;
+#else
+		uint64_t wodt_d2_r0:8;
+		uint64_t wodt_d2_r1:8;
+		uint64_t wodt_d3_r0:8;
+		uint64_t wodt_d3_r1:8;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_lmcx_wodt_mask {
+	uint64_t u64;
+	struct cvmx_lmcx_wodt_mask_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t wodt_d3_r1:8;
+		uint64_t wodt_d3_r0:8;
+		uint64_t wodt_d2_r1:8;
+		uint64_t wodt_d2_r0:8;
+		uint64_t wodt_d1_r1:8;
+		uint64_t wodt_d1_r0:8;
+		uint64_t wodt_d0_r1:8;
+		uint64_t wodt_d0_r0:8;
+#else
+		uint64_t wodt_d0_r0:8;
+		uint64_t wodt_d0_r1:8;
+		uint64_t wodt_d1_r0:8;
+		uint64_t wodt_d1_r1:8;
+		uint64_t wodt_d2_r0:8;
+		uint64_t wodt_d2_r1:8;
+		uint64_t wodt_d3_r0:8;
+		uint64_t wodt_d3_r1:8;
+#endif
+	} s;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-mio-defs.h b/arch/mips/include/asm/octeon/cvmx-mio-defs.h
new file mode 100644
index 000000000..4ad95d040
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-mio-defs.h
@@ -0,0 +1,4396 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2012 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_MIO_DEFS_H__
+#define __CVMX_MIO_DEFS_H__
+
+#define CVMX_MIO_BOOT_BIST_STAT (CVMX_ADD_IO_SEG(0x00011800000000F8ull))
+#define CVMX_MIO_BOOT_COMP (CVMX_ADD_IO_SEG(0x00011800000000B8ull))
+#define CVMX_MIO_BOOT_DMA_CFGX(offset) (CVMX_ADD_IO_SEG(0x0001180000000100ull) + ((offset) & 3) * 8)
+#define CVMX_MIO_BOOT_DMA_INTX(offset) (CVMX_ADD_IO_SEG(0x0001180000000138ull) + ((offset) & 3) * 8)
+#define CVMX_MIO_BOOT_DMA_INT_ENX(offset) (CVMX_ADD_IO_SEG(0x0001180000000150ull) + ((offset) & 3) * 8)
+#define CVMX_MIO_BOOT_DMA_TIMX(offset) (CVMX_ADD_IO_SEG(0x0001180000000120ull) + ((offset) & 3) * 8)
+#define CVMX_MIO_BOOT_ERR (CVMX_ADD_IO_SEG(0x00011800000000A0ull))
+#define CVMX_MIO_BOOT_INT (CVMX_ADD_IO_SEG(0x00011800000000A8ull))
+#define CVMX_MIO_BOOT_LOC_ADR (CVMX_ADD_IO_SEG(0x0001180000000090ull))
+#define CVMX_MIO_BOOT_LOC_CFGX(offset) (CVMX_ADD_IO_SEG(0x0001180000000080ull) + ((offset) & 1) * 8)
+#define CVMX_MIO_BOOT_LOC_DAT (CVMX_ADD_IO_SEG(0x0001180000000098ull))
+#define CVMX_MIO_BOOT_PIN_DEFS (CVMX_ADD_IO_SEG(0x00011800000000C0ull))
+#define CVMX_MIO_BOOT_REG_CFGX(offset) (CVMX_ADD_IO_SEG(0x0001180000000000ull) + ((offset) & 7) * 8)
+#define CVMX_MIO_BOOT_REG_TIMX(offset) (CVMX_ADD_IO_SEG(0x0001180000000040ull) + ((offset) & 7) * 8)
+#define CVMX_MIO_BOOT_THR (CVMX_ADD_IO_SEG(0x00011800000000B0ull))
+#define CVMX_MIO_EMM_BUF_DAT (CVMX_ADD_IO_SEG(0x00011800000020E8ull))
+#define CVMX_MIO_EMM_BUF_IDX (CVMX_ADD_IO_SEG(0x00011800000020E0ull))
+#define CVMX_MIO_EMM_CFG (CVMX_ADD_IO_SEG(0x0001180000002000ull))
+#define CVMX_MIO_EMM_CMD (CVMX_ADD_IO_SEG(0x0001180000002058ull))
+#define CVMX_MIO_EMM_DMA (CVMX_ADD_IO_SEG(0x0001180000002050ull))
+#define CVMX_MIO_EMM_INT (CVMX_ADD_IO_SEG(0x0001180000002078ull))
+#define CVMX_MIO_EMM_INT_EN (CVMX_ADD_IO_SEG(0x0001180000002080ull))
+#define CVMX_MIO_EMM_MODEX(offset) (CVMX_ADD_IO_SEG(0x0001180000002008ull) + ((offset) & 3) * 8)
+#define CVMX_MIO_EMM_RCA (CVMX_ADD_IO_SEG(0x00011800000020A0ull))
+#define CVMX_MIO_EMM_RSP_HI (CVMX_ADD_IO_SEG(0x0001180000002070ull))
+#define CVMX_MIO_EMM_RSP_LO (CVMX_ADD_IO_SEG(0x0001180000002068ull))
+#define CVMX_MIO_EMM_RSP_STS (CVMX_ADD_IO_SEG(0x0001180000002060ull))
+#define CVMX_MIO_EMM_SAMPLE (CVMX_ADD_IO_SEG(0x0001180000002090ull))
+#define CVMX_MIO_EMM_STS_MASK (CVMX_ADD_IO_SEG(0x0001180000002098ull))
+#define CVMX_MIO_EMM_SWITCH (CVMX_ADD_IO_SEG(0x0001180000002048ull))
+#define CVMX_MIO_EMM_WDOG (CVMX_ADD_IO_SEG(0x0001180000002088ull))
+#define CVMX_MIO_FUS_BNK_DATX(offset) (CVMX_ADD_IO_SEG(0x0001180000001520ull) + ((offset) & 3) * 8)
+#define CVMX_MIO_FUS_DAT0 (CVMX_ADD_IO_SEG(0x0001180000001400ull))
+#define CVMX_MIO_FUS_DAT1 (CVMX_ADD_IO_SEG(0x0001180000001408ull))
+#define CVMX_MIO_FUS_DAT2 (CVMX_ADD_IO_SEG(0x0001180000001410ull))
+#define CVMX_MIO_FUS_DAT3 (CVMX_ADD_IO_SEG(0x0001180000001418ull))
+#define CVMX_MIO_FUS_EMA (CVMX_ADD_IO_SEG(0x0001180000001550ull))
+#define CVMX_MIO_FUS_PDF (CVMX_ADD_IO_SEG(0x0001180000001420ull))
+#define CVMX_MIO_FUS_PLL (CVMX_ADD_IO_SEG(0x0001180000001580ull))
+#define CVMX_MIO_FUS_PROG (CVMX_ADD_IO_SEG(0x0001180000001510ull))
+#define CVMX_MIO_FUS_PROG_TIMES (CVMX_ADD_IO_SEG(0x0001180000001518ull))
+#define CVMX_MIO_FUS_RCMD (CVMX_ADD_IO_SEG(0x0001180000001500ull))
+#define CVMX_MIO_FUS_READ_TIMES (CVMX_ADD_IO_SEG(0x0001180000001570ull))
+#define CVMX_MIO_FUS_REPAIR_RES0 (CVMX_ADD_IO_SEG(0x0001180000001558ull))
+#define CVMX_MIO_FUS_REPAIR_RES1 (CVMX_ADD_IO_SEG(0x0001180000001560ull))
+#define CVMX_MIO_FUS_REPAIR_RES2 (CVMX_ADD_IO_SEG(0x0001180000001568ull))
+#define CVMX_MIO_FUS_SPR_REPAIR_RES (CVMX_ADD_IO_SEG(0x0001180000001548ull))
+#define CVMX_MIO_FUS_SPR_REPAIR_SUM (CVMX_ADD_IO_SEG(0x0001180000001540ull))
+#define CVMX_MIO_FUS_TGG (CVMX_ADD_IO_SEG(0x0001180000001428ull))
+#define CVMX_MIO_FUS_UNLOCK (CVMX_ADD_IO_SEG(0x0001180000001578ull))
+#define CVMX_MIO_FUS_WADR (CVMX_ADD_IO_SEG(0x0001180000001508ull))
+#define CVMX_MIO_GPIO_COMP (CVMX_ADD_IO_SEG(0x00011800000000C8ull))
+#define CVMX_MIO_NDF_DMA_CFG (CVMX_ADD_IO_SEG(0x0001180000000168ull))
+#define CVMX_MIO_NDF_DMA_INT (CVMX_ADD_IO_SEG(0x0001180000000170ull))
+#define CVMX_MIO_NDF_DMA_INT_EN (CVMX_ADD_IO_SEG(0x0001180000000178ull))
+#define CVMX_MIO_PLL_CTL (CVMX_ADD_IO_SEG(0x0001180000001448ull))
+#define CVMX_MIO_PLL_SETTING (CVMX_ADD_IO_SEG(0x0001180000001440ull))
+#define CVMX_MIO_PTP_CKOUT_HI_INCR (CVMX_ADD_IO_SEG(0x0001070000000F40ull))
+#define CVMX_MIO_PTP_CKOUT_LO_INCR (CVMX_ADD_IO_SEG(0x0001070000000F48ull))
+#define CVMX_MIO_PTP_CKOUT_THRESH_HI (CVMX_ADD_IO_SEG(0x0001070000000F38ull))
+#define CVMX_MIO_PTP_CKOUT_THRESH_LO (CVMX_ADD_IO_SEG(0x0001070000000F30ull))
+#define CVMX_MIO_PTP_CLOCK_CFG (CVMX_ADD_IO_SEG(0x0001070000000F00ull))
+#define CVMX_MIO_PTP_CLOCK_COMP (CVMX_ADD_IO_SEG(0x0001070000000F18ull))
+#define CVMX_MIO_PTP_CLOCK_HI (CVMX_ADD_IO_SEG(0x0001070000000F10ull))
+#define CVMX_MIO_PTP_CLOCK_LO (CVMX_ADD_IO_SEG(0x0001070000000F08ull))
+#define CVMX_MIO_PTP_EVT_CNT (CVMX_ADD_IO_SEG(0x0001070000000F28ull))
+#define CVMX_MIO_PTP_PHY_1PPS_IN (CVMX_ADD_IO_SEG(0x0001070000000F70ull))
+#define CVMX_MIO_PTP_PPS_HI_INCR (CVMX_ADD_IO_SEG(0x0001070000000F60ull))
+#define CVMX_MIO_PTP_PPS_LO_INCR (CVMX_ADD_IO_SEG(0x0001070000000F68ull))
+#define CVMX_MIO_PTP_PPS_THRESH_HI (CVMX_ADD_IO_SEG(0x0001070000000F58ull))
+#define CVMX_MIO_PTP_PPS_THRESH_LO (CVMX_ADD_IO_SEG(0x0001070000000F50ull))
+#define CVMX_MIO_PTP_TIMESTAMP (CVMX_ADD_IO_SEG(0x0001070000000F20ull))
+#define CVMX_MIO_QLMX_CFG(offset) (CVMX_ADD_IO_SEG(0x0001180000001590ull) + ((offset) & 7) * 8)
+#define CVMX_MIO_RST_BOOT (CVMX_ADD_IO_SEG(0x0001180000001600ull))
+#define CVMX_MIO_RST_CFG (CVMX_ADD_IO_SEG(0x0001180000001610ull))
+#define CVMX_MIO_RST_CKILL (CVMX_ADD_IO_SEG(0x0001180000001638ull))
+#define CVMX_MIO_RST_CNTLX(offset) (CVMX_ADD_IO_SEG(0x0001180000001648ull) + ((offset) & 3) * 8)
+#define CVMX_MIO_RST_CTLX(offset) (CVMX_ADD_IO_SEG(0x0001180000001618ull) + ((offset) & 1) * 8)
+#define CVMX_MIO_RST_DELAY (CVMX_ADD_IO_SEG(0x0001180000001608ull))
+#define CVMX_MIO_RST_INT (CVMX_ADD_IO_SEG(0x0001180000001628ull))
+#define CVMX_MIO_RST_INT_EN (CVMX_ADD_IO_SEG(0x0001180000001630ull))
+#define CVMX_MIO_TWSX_INT(offset) (CVMX_ADD_IO_SEG(0x0001180000001010ull) + ((offset) & 1) * 512)
+#define CVMX_MIO_TWSX_SW_TWSI(offset) (CVMX_ADD_IO_SEG(0x0001180000001000ull) + ((offset) & 1) * 512)
+#define CVMX_MIO_TWSX_SW_TWSI_EXT(offset) (CVMX_ADD_IO_SEG(0x0001180000001018ull) + ((offset) & 1) * 512)
+#define CVMX_MIO_TWSX_TWSI_SW(offset) (CVMX_ADD_IO_SEG(0x0001180000001008ull) + ((offset) & 1) * 512)
+#define CVMX_MIO_UART2_DLH (CVMX_ADD_IO_SEG(0x0001180000000488ull))
+#define CVMX_MIO_UART2_DLL (CVMX_ADD_IO_SEG(0x0001180000000480ull))
+#define CVMX_MIO_UART2_FAR (CVMX_ADD_IO_SEG(0x0001180000000520ull))
+#define CVMX_MIO_UART2_FCR (CVMX_ADD_IO_SEG(0x0001180000000450ull))
+#define CVMX_MIO_UART2_HTX (CVMX_ADD_IO_SEG(0x0001180000000708ull))
+#define CVMX_MIO_UART2_IER (CVMX_ADD_IO_SEG(0x0001180000000408ull))
+#define CVMX_MIO_UART2_IIR (CVMX_ADD_IO_SEG(0x0001180000000410ull))
+#define CVMX_MIO_UART2_LCR (CVMX_ADD_IO_SEG(0x0001180000000418ull))
+#define CVMX_MIO_UART2_LSR (CVMX_ADD_IO_SEG(0x0001180000000428ull))
+#define CVMX_MIO_UART2_MCR (CVMX_ADD_IO_SEG(0x0001180000000420ull))
+#define CVMX_MIO_UART2_MSR (CVMX_ADD_IO_SEG(0x0001180000000430ull))
+#define CVMX_MIO_UART2_RBR (CVMX_ADD_IO_SEG(0x0001180000000400ull))
+#define CVMX_MIO_UART2_RFL (CVMX_ADD_IO_SEG(0x0001180000000608ull))
+#define CVMX_MIO_UART2_RFW (CVMX_ADD_IO_SEG(0x0001180000000530ull))
+#define CVMX_MIO_UART2_SBCR (CVMX_ADD_IO_SEG(0x0001180000000620ull))
+#define CVMX_MIO_UART2_SCR (CVMX_ADD_IO_SEG(0x0001180000000438ull))
+#define CVMX_MIO_UART2_SFE (CVMX_ADD_IO_SEG(0x0001180000000630ull))
+#define CVMX_MIO_UART2_SRR (CVMX_ADD_IO_SEG(0x0001180000000610ull))
+#define CVMX_MIO_UART2_SRT (CVMX_ADD_IO_SEG(0x0001180000000638ull))
+#define CVMX_MIO_UART2_SRTS (CVMX_ADD_IO_SEG(0x0001180000000618ull))
+#define CVMX_MIO_UART2_STT (CVMX_ADD_IO_SEG(0x0001180000000700ull))
+#define CVMX_MIO_UART2_TFL (CVMX_ADD_IO_SEG(0x0001180000000600ull))
+#define CVMX_MIO_UART2_TFR (CVMX_ADD_IO_SEG(0x0001180000000528ull))
+#define CVMX_MIO_UART2_THR (CVMX_ADD_IO_SEG(0x0001180000000440ull))
+#define CVMX_MIO_UART2_USR (CVMX_ADD_IO_SEG(0x0001180000000538ull))
+#define CVMX_MIO_UARTX_DLH(offset) (CVMX_ADD_IO_SEG(0x0001180000000888ull) + ((offset) & 1) * 1024)
+#define CVMX_MIO_UARTX_DLL(offset) (CVMX_ADD_IO_SEG(0x0001180000000880ull) + ((offset) & 1) * 1024)
+#define CVMX_MIO_UARTX_FAR(offset) (CVMX_ADD_IO_SEG(0x0001180000000920ull) + ((offset) & 1) * 1024)
+#define CVMX_MIO_UARTX_FCR(offset) (CVMX_ADD_IO_SEG(0x0001180000000850ull) + ((offset) & 1) * 1024)
+#define CVMX_MIO_UARTX_HTX(offset) (CVMX_ADD_IO_SEG(0x0001180000000B08ull) + ((offset) & 1) * 1024)
+#define CVMX_MIO_UARTX_IER(offset) (CVMX_ADD_IO_SEG(0x0001180000000808ull) + ((offset) & 1) * 1024)
+#define CVMX_MIO_UARTX_IIR(offset) (CVMX_ADD_IO_SEG(0x0001180000000810ull) + ((offset) & 1) * 1024)
+#define CVMX_MIO_UARTX_LCR(offset) (CVMX_ADD_IO_SEG(0x0001180000000818ull) + ((offset) & 1) * 1024)
+#define CVMX_MIO_UARTX_LSR(offset) (CVMX_ADD_IO_SEG(0x0001180000000828ull) + ((offset) & 1) * 1024)
+#define CVMX_MIO_UARTX_MCR(offset) (CVMX_ADD_IO_SEG(0x0001180000000820ull) + ((offset) & 1) * 1024)
+#define CVMX_MIO_UARTX_MSR(offset) (CVMX_ADD_IO_SEG(0x0001180000000830ull) + ((offset) & 1) * 1024)
+#define CVMX_MIO_UARTX_RBR(offset) (CVMX_ADD_IO_SEG(0x0001180000000800ull) + ((offset) & 1) * 1024)
+#define CVMX_MIO_UARTX_RFL(offset) (CVMX_ADD_IO_SEG(0x0001180000000A08ull) + ((offset) & 1) * 1024)
+#define CVMX_MIO_UARTX_RFW(offset) (CVMX_ADD_IO_SEG(0x0001180000000930ull) + ((offset) & 1) * 1024)
+#define CVMX_MIO_UARTX_SBCR(offset) (CVMX_ADD_IO_SEG(0x0001180000000A20ull) + ((offset) & 1) * 1024)
+#define CVMX_MIO_UARTX_SCR(offset) (CVMX_ADD_IO_SEG(0x0001180000000838ull) + ((offset) & 1) * 1024)
+#define CVMX_MIO_UARTX_SFE(offset) (CVMX_ADD_IO_SEG(0x0001180000000A30ull) + ((offset) & 1) * 1024)
+#define CVMX_MIO_UARTX_SRR(offset) (CVMX_ADD_IO_SEG(0x0001180000000A10ull) + ((offset) & 1) * 1024)
+#define CVMX_MIO_UARTX_SRT(offset) (CVMX_ADD_IO_SEG(0x0001180000000A38ull) + ((offset) & 1) * 1024)
+#define CVMX_MIO_UARTX_SRTS(offset) (CVMX_ADD_IO_SEG(0x0001180000000A18ull) + ((offset) & 1) * 1024)
+#define CVMX_MIO_UARTX_STT(offset) (CVMX_ADD_IO_SEG(0x0001180000000B00ull) + ((offset) & 1) * 1024)
+#define CVMX_MIO_UARTX_TFL(offset) (CVMX_ADD_IO_SEG(0x0001180000000A00ull) + ((offset) & 1) * 1024)
+#define CVMX_MIO_UARTX_TFR(offset) (CVMX_ADD_IO_SEG(0x0001180000000928ull) + ((offset) & 1) * 1024)
+#define CVMX_MIO_UARTX_THR(offset) (CVMX_ADD_IO_SEG(0x0001180000000840ull) + ((offset) & 1) * 1024)
+#define CVMX_MIO_UARTX_USR(offset) (CVMX_ADD_IO_SEG(0x0001180000000938ull) + ((offset) & 1) * 1024)
+
+union cvmx_mio_boot_bist_stat {
+	uint64_t u64;
+	struct cvmx_mio_boot_bist_stat_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_0_63:64;
+#else
+		uint64_t reserved_0_63:64;
+#endif
+	} s;
+	struct cvmx_mio_boot_bist_stat_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t ncbo_1:1;
+		uint64_t ncbo_0:1;
+		uint64_t loc:1;
+		uint64_t ncbi:1;
+#else
+		uint64_t ncbi:1;
+		uint64_t loc:1;
+		uint64_t ncbo_0:1;
+		uint64_t ncbo_1:1;
+		uint64_t reserved_4_63:60;
+#endif
+	} cn30xx;
+	struct cvmx_mio_boot_bist_stat_cn38xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_3_63:61;
+		uint64_t ncbo_0:1;
+		uint64_t loc:1;
+		uint64_t ncbi:1;
+#else
+		uint64_t ncbi:1;
+		uint64_t loc:1;
+		uint64_t ncbo_0:1;
+		uint64_t reserved_3_63:61;
+#endif
+	} cn38xx;
+	struct cvmx_mio_boot_bist_stat_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t pcm_1:1;
+		uint64_t pcm_0:1;
+		uint64_t ncbo_1:1;
+		uint64_t ncbo_0:1;
+		uint64_t loc:1;
+		uint64_t ncbi:1;
+#else
+		uint64_t ncbi:1;
+		uint64_t loc:1;
+		uint64_t ncbo_0:1;
+		uint64_t ncbo_1:1;
+		uint64_t pcm_0:1;
+		uint64_t pcm_1:1;
+		uint64_t reserved_6_63:58;
+#endif
+	} cn50xx;
+	struct cvmx_mio_boot_bist_stat_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t ndf:2;
+		uint64_t ncbo_0:1;
+		uint64_t dma:1;
+		uint64_t loc:1;
+		uint64_t ncbi:1;
+#else
+		uint64_t ncbi:1;
+		uint64_t loc:1;
+		uint64_t dma:1;
+		uint64_t ncbo_0:1;
+		uint64_t ndf:2;
+		uint64_t reserved_6_63:58;
+#endif
+	} cn52xx;
+	struct cvmx_mio_boot_bist_stat_cn52xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t ncbo_0:1;
+		uint64_t dma:1;
+		uint64_t loc:1;
+		uint64_t ncbi:1;
+#else
+		uint64_t ncbi:1;
+		uint64_t loc:1;
+		uint64_t dma:1;
+		uint64_t ncbo_0:1;
+		uint64_t reserved_4_63:60;
+#endif
+	} cn52xxp1;
+	struct cvmx_mio_boot_bist_stat_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t stat:12;
+#else
+		uint64_t stat:12;
+		uint64_t reserved_12_63:52;
+#endif
+	} cn61xx;
+	struct cvmx_mio_boot_bist_stat_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_9_63:55;
+		uint64_t stat:9;
+#else
+		uint64_t stat:9;
+		uint64_t reserved_9_63:55;
+#endif
+	} cn63xx;
+	struct cvmx_mio_boot_bist_stat_cn66xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t stat:10;
+#else
+		uint64_t stat:10;
+		uint64_t reserved_10_63:54;
+#endif
+	} cn66xx;
+};
+
+union cvmx_mio_boot_comp {
+	uint64_t u64;
+	struct cvmx_mio_boot_comp_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_0_63:64;
+#else
+		uint64_t reserved_0_63:64;
+#endif
+	} s;
+	struct cvmx_mio_boot_comp_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t pctl:5;
+		uint64_t nctl:5;
+#else
+		uint64_t nctl:5;
+		uint64_t pctl:5;
+		uint64_t reserved_10_63:54;
+#endif
+	} cn50xx;
+	struct cvmx_mio_boot_comp_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t pctl:6;
+		uint64_t nctl:6;
+#else
+		uint64_t nctl:6;
+		uint64_t pctl:6;
+		uint64_t reserved_12_63:52;
+#endif
+	} cn61xx;
+};
+
+union cvmx_mio_boot_dma_cfgx {
+	uint64_t u64;
+	struct cvmx_mio_boot_dma_cfgx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t en:1;
+		uint64_t rw:1;
+		uint64_t clr:1;
+		uint64_t reserved_60_60:1;
+		uint64_t swap32:1;
+		uint64_t swap16:1;
+		uint64_t swap8:1;
+		uint64_t endian:1;
+		uint64_t size:20;
+		uint64_t adr:36;
+#else
+		uint64_t adr:36;
+		uint64_t size:20;
+		uint64_t endian:1;
+		uint64_t swap8:1;
+		uint64_t swap16:1;
+		uint64_t swap32:1;
+		uint64_t reserved_60_60:1;
+		uint64_t clr:1;
+		uint64_t rw:1;
+		uint64_t en:1;
+#endif
+	} s;
+};
+
+union cvmx_mio_boot_dma_intx {
+	uint64_t u64;
+	struct cvmx_mio_boot_dma_intx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t dmarq:1;
+		uint64_t done:1;
+#else
+		uint64_t done:1;
+		uint64_t dmarq:1;
+		uint64_t reserved_2_63:62;
+#endif
+	} s;
+};
+
+union cvmx_mio_boot_dma_int_enx {
+	uint64_t u64;
+	struct cvmx_mio_boot_dma_int_enx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t dmarq:1;
+		uint64_t done:1;
+#else
+		uint64_t done:1;
+		uint64_t dmarq:1;
+		uint64_t reserved_2_63:62;
+#endif
+	} s;
+};
+
+union cvmx_mio_boot_dma_timx {
+	uint64_t u64;
+	struct cvmx_mio_boot_dma_timx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t dmack_pi:1;
+		uint64_t dmarq_pi:1;
+		uint64_t tim_mult:2;
+		uint64_t rd_dly:3;
+		uint64_t ddr:1;
+		uint64_t width:1;
+		uint64_t reserved_48_54:7;
+		uint64_t pause:6;
+		uint64_t dmack_h:6;
+		uint64_t we_n:6;
+		uint64_t we_a:6;
+		uint64_t oe_n:6;
+		uint64_t oe_a:6;
+		uint64_t dmack_s:6;
+		uint64_t dmarq:6;
+#else
+		uint64_t dmarq:6;
+		uint64_t dmack_s:6;
+		uint64_t oe_a:6;
+		uint64_t oe_n:6;
+		uint64_t we_a:6;
+		uint64_t we_n:6;
+		uint64_t dmack_h:6;
+		uint64_t pause:6;
+		uint64_t reserved_48_54:7;
+		uint64_t width:1;
+		uint64_t ddr:1;
+		uint64_t rd_dly:3;
+		uint64_t tim_mult:2;
+		uint64_t dmarq_pi:1;
+		uint64_t dmack_pi:1;
+#endif
+	} s;
+};
+
+union cvmx_mio_boot_err {
+	uint64_t u64;
+	struct cvmx_mio_boot_err_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t wait_err:1;
+		uint64_t adr_err:1;
+#else
+		uint64_t adr_err:1;
+		uint64_t wait_err:1;
+		uint64_t reserved_2_63:62;
+#endif
+	} s;
+};
+
+union cvmx_mio_boot_int {
+	uint64_t u64;
+	struct cvmx_mio_boot_int_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t wait_int:1;
+		uint64_t adr_int:1;
+#else
+		uint64_t adr_int:1;
+		uint64_t wait_int:1;
+		uint64_t reserved_2_63:62;
+#endif
+	} s;
+};
+
+union cvmx_mio_boot_loc_adr {
+	uint64_t u64;
+	struct cvmx_mio_boot_loc_adr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t adr:5;
+		uint64_t reserved_0_2:3;
+#else
+		uint64_t reserved_0_2:3;
+		uint64_t adr:5;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_mio_boot_loc_cfgx {
+	uint64_t u64;
+	struct cvmx_mio_boot_loc_cfgx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t en:1;
+		uint64_t reserved_28_30:3;
+		uint64_t base:25;
+		uint64_t reserved_0_2:3;
+#else
+		uint64_t reserved_0_2:3;
+		uint64_t base:25;
+		uint64_t reserved_28_30:3;
+		uint64_t en:1;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_mio_boot_loc_dat {
+	uint64_t u64;
+	struct cvmx_mio_boot_loc_dat_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t data:64;
+#else
+		uint64_t data:64;
+#endif
+	} s;
+};
+
+union cvmx_mio_boot_pin_defs {
+	uint64_t u64;
+	struct cvmx_mio_boot_pin_defs_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t user1:16;
+		uint64_t ale:1;
+		uint64_t width:1;
+		uint64_t dmack_p2:1;
+		uint64_t dmack_p1:1;
+		uint64_t dmack_p0:1;
+		uint64_t term:2;
+		uint64_t nand:1;
+		uint64_t user0:8;
+#else
+		uint64_t user0:8;
+		uint64_t nand:1;
+		uint64_t term:2;
+		uint64_t dmack_p0:1;
+		uint64_t dmack_p1:1;
+		uint64_t dmack_p2:1;
+		uint64_t width:1;
+		uint64_t ale:1;
+		uint64_t user1:16;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+	struct cvmx_mio_boot_pin_defs_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t ale:1;
+		uint64_t width:1;
+		uint64_t reserved_13_13:1;
+		uint64_t dmack_p1:1;
+		uint64_t dmack_p0:1;
+		uint64_t term:2;
+		uint64_t nand:1;
+		uint64_t reserved_0_7:8;
+#else
+		uint64_t reserved_0_7:8;
+		uint64_t nand:1;
+		uint64_t term:2;
+		uint64_t dmack_p0:1;
+		uint64_t dmack_p1:1;
+		uint64_t reserved_13_13:1;
+		uint64_t width:1;
+		uint64_t ale:1;
+		uint64_t reserved_16_63:48;
+#endif
+	} cn52xx;
+	struct cvmx_mio_boot_pin_defs_cn56xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t ale:1;
+		uint64_t width:1;
+		uint64_t dmack_p2:1;
+		uint64_t dmack_p1:1;
+		uint64_t dmack_p0:1;
+		uint64_t term:2;
+		uint64_t reserved_0_8:9;
+#else
+		uint64_t reserved_0_8:9;
+		uint64_t term:2;
+		uint64_t dmack_p0:1;
+		uint64_t dmack_p1:1;
+		uint64_t dmack_p2:1;
+		uint64_t width:1;
+		uint64_t ale:1;
+		uint64_t reserved_16_63:48;
+#endif
+	} cn56xx;
+	struct cvmx_mio_boot_pin_defs_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t user1:16;
+		uint64_t ale:1;
+		uint64_t width:1;
+		uint64_t reserved_13_13:1;
+		uint64_t dmack_p1:1;
+		uint64_t dmack_p0:1;
+		uint64_t term:2;
+		uint64_t nand:1;
+		uint64_t user0:8;
+#else
+		uint64_t user0:8;
+		uint64_t nand:1;
+		uint64_t term:2;
+		uint64_t dmack_p0:1;
+		uint64_t dmack_p1:1;
+		uint64_t reserved_13_13:1;
+		uint64_t width:1;
+		uint64_t ale:1;
+		uint64_t user1:16;
+		uint64_t reserved_32_63:32;
+#endif
+	} cn61xx;
+};
+
+union cvmx_mio_boot_reg_cfgx {
+	uint64_t u64;
+	struct cvmx_mio_boot_reg_cfgx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_44_63:20;
+		uint64_t dmack:2;
+		uint64_t tim_mult:2;
+		uint64_t rd_dly:3;
+		uint64_t sam:1;
+		uint64_t we_ext:2;
+		uint64_t oe_ext:2;
+		uint64_t en:1;
+		uint64_t orbit:1;
+		uint64_t ale:1;
+		uint64_t width:1;
+		uint64_t size:12;
+		uint64_t base:16;
+#else
+		uint64_t base:16;
+		uint64_t size:12;
+		uint64_t width:1;
+		uint64_t ale:1;
+		uint64_t orbit:1;
+		uint64_t en:1;
+		uint64_t oe_ext:2;
+		uint64_t we_ext:2;
+		uint64_t sam:1;
+		uint64_t rd_dly:3;
+		uint64_t tim_mult:2;
+		uint64_t dmack:2;
+		uint64_t reserved_44_63:20;
+#endif
+	} s;
+	struct cvmx_mio_boot_reg_cfgx_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_37_63:27;
+		uint64_t sam:1;
+		uint64_t we_ext:2;
+		uint64_t oe_ext:2;
+		uint64_t en:1;
+		uint64_t orbit:1;
+		uint64_t ale:1;
+		uint64_t width:1;
+		uint64_t size:12;
+		uint64_t base:16;
+#else
+		uint64_t base:16;
+		uint64_t size:12;
+		uint64_t width:1;
+		uint64_t ale:1;
+		uint64_t orbit:1;
+		uint64_t en:1;
+		uint64_t oe_ext:2;
+		uint64_t we_ext:2;
+		uint64_t sam:1;
+		uint64_t reserved_37_63:27;
+#endif
+	} cn30xx;
+	struct cvmx_mio_boot_reg_cfgx_cn38xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t en:1;
+		uint64_t orbit:1;
+		uint64_t reserved_28_29:2;
+		uint64_t size:12;
+		uint64_t base:16;
+#else
+		uint64_t base:16;
+		uint64_t size:12;
+		uint64_t reserved_28_29:2;
+		uint64_t orbit:1;
+		uint64_t en:1;
+		uint64_t reserved_32_63:32;
+#endif
+	} cn38xx;
+	struct cvmx_mio_boot_reg_cfgx_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_42_63:22;
+		uint64_t tim_mult:2;
+		uint64_t rd_dly:3;
+		uint64_t sam:1;
+		uint64_t we_ext:2;
+		uint64_t oe_ext:2;
+		uint64_t en:1;
+		uint64_t orbit:1;
+		uint64_t ale:1;
+		uint64_t width:1;
+		uint64_t size:12;
+		uint64_t base:16;
+#else
+		uint64_t base:16;
+		uint64_t size:12;
+		uint64_t width:1;
+		uint64_t ale:1;
+		uint64_t orbit:1;
+		uint64_t en:1;
+		uint64_t oe_ext:2;
+		uint64_t we_ext:2;
+		uint64_t sam:1;
+		uint64_t rd_dly:3;
+		uint64_t tim_mult:2;
+		uint64_t reserved_42_63:22;
+#endif
+	} cn50xx;
+};
+
+union cvmx_mio_boot_reg_timx {
+	uint64_t u64;
+	struct cvmx_mio_boot_reg_timx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t pagem:1;
+		uint64_t waitm:1;
+		uint64_t pages:2;
+		uint64_t ale:6;
+		uint64_t page:6;
+		uint64_t wait:6;
+		uint64_t pause:6;
+		uint64_t wr_hld:6;
+		uint64_t rd_hld:6;
+		uint64_t we:6;
+		uint64_t oe:6;
+		uint64_t ce:6;
+		uint64_t adr:6;
+#else
+		uint64_t adr:6;
+		uint64_t ce:6;
+		uint64_t oe:6;
+		uint64_t we:6;
+		uint64_t rd_hld:6;
+		uint64_t wr_hld:6;
+		uint64_t pause:6;
+		uint64_t wait:6;
+		uint64_t page:6;
+		uint64_t ale:6;
+		uint64_t pages:2;
+		uint64_t waitm:1;
+		uint64_t pagem:1;
+#endif
+	} s;
+	struct cvmx_mio_boot_reg_timx_cn38xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t pagem:1;
+		uint64_t waitm:1;
+		uint64_t pages:2;
+		uint64_t reserved_54_59:6;
+		uint64_t page:6;
+		uint64_t wait:6;
+		uint64_t pause:6;
+		uint64_t wr_hld:6;
+		uint64_t rd_hld:6;
+		uint64_t we:6;
+		uint64_t oe:6;
+		uint64_t ce:6;
+		uint64_t adr:6;
+#else
+		uint64_t adr:6;
+		uint64_t ce:6;
+		uint64_t oe:6;
+		uint64_t we:6;
+		uint64_t rd_hld:6;
+		uint64_t wr_hld:6;
+		uint64_t pause:6;
+		uint64_t wait:6;
+		uint64_t page:6;
+		uint64_t reserved_54_59:6;
+		uint64_t pages:2;
+		uint64_t waitm:1;
+		uint64_t pagem:1;
+#endif
+	} cn38xx;
+};
+
+union cvmx_mio_boot_thr {
+	uint64_t u64;
+	struct cvmx_mio_boot_thr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_22_63:42;
+		uint64_t dma_thr:6;
+		uint64_t reserved_14_15:2;
+		uint64_t fif_cnt:6;
+		uint64_t reserved_6_7:2;
+		uint64_t fif_thr:6;
+#else
+		uint64_t fif_thr:6;
+		uint64_t reserved_6_7:2;
+		uint64_t fif_cnt:6;
+		uint64_t reserved_14_15:2;
+		uint64_t dma_thr:6;
+		uint64_t reserved_22_63:42;
+#endif
+	} s;
+	struct cvmx_mio_boot_thr_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_14_63:50;
+		uint64_t fif_cnt:6;
+		uint64_t reserved_6_7:2;
+		uint64_t fif_thr:6;
+#else
+		uint64_t fif_thr:6;
+		uint64_t reserved_6_7:2;
+		uint64_t fif_cnt:6;
+		uint64_t reserved_14_63:50;
+#endif
+	} cn30xx;
+};
+
+union cvmx_mio_emm_buf_dat {
+	uint64_t u64;
+	struct cvmx_mio_emm_buf_dat_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t dat:64;
+#else
+		uint64_t dat:64;
+#endif
+	} s;
+};
+
+union cvmx_mio_emm_buf_idx {
+	uint64_t u64;
+	struct cvmx_mio_emm_buf_idx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_17_63:47;
+		uint64_t inc:1;
+		uint64_t reserved_7_15:9;
+		uint64_t buf_num:1;
+		uint64_t offset:6;
+#else
+		uint64_t offset:6;
+		uint64_t buf_num:1;
+		uint64_t reserved_7_15:9;
+		uint64_t inc:1;
+		uint64_t reserved_17_63:47;
+#endif
+	} s;
+};
+
+union cvmx_mio_emm_cfg {
+	uint64_t u64;
+	struct cvmx_mio_emm_cfg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_17_63:47;
+		uint64_t boot_fail:1;
+		uint64_t reserved_4_15:12;
+		uint64_t bus_ena:4;
+#else
+		uint64_t bus_ena:4;
+		uint64_t reserved_4_15:12;
+		uint64_t boot_fail:1;
+		uint64_t reserved_17_63:47;
+#endif
+	} s;
+};
+
+union cvmx_mio_emm_cmd {
+	uint64_t u64;
+	struct cvmx_mio_emm_cmd_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_62_63:2;
+		uint64_t bus_id:2;
+		uint64_t cmd_val:1;
+		uint64_t reserved_56_58:3;
+		uint64_t dbuf:1;
+		uint64_t offset:6;
+		uint64_t reserved_43_48:6;
+		uint64_t ctype_xor:2;
+		uint64_t rtype_xor:3;
+		uint64_t cmd_idx:6;
+		uint64_t arg:32;
+#else
+		uint64_t arg:32;
+		uint64_t cmd_idx:6;
+		uint64_t rtype_xor:3;
+		uint64_t ctype_xor:2;
+		uint64_t reserved_43_48:6;
+		uint64_t offset:6;
+		uint64_t dbuf:1;
+		uint64_t reserved_56_58:3;
+		uint64_t cmd_val:1;
+		uint64_t bus_id:2;
+		uint64_t reserved_62_63:2;
+#endif
+	} s;
+};
+
+union cvmx_mio_emm_dma {
+	uint64_t u64;
+	struct cvmx_mio_emm_dma_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_62_63:2;
+		uint64_t bus_id:2;
+		uint64_t dma_val:1;
+		uint64_t sector:1;
+		uint64_t dat_null:1;
+		uint64_t thres:6;
+		uint64_t rel_wr:1;
+		uint64_t rw:1;
+		uint64_t multi:1;
+		uint64_t block_cnt:16;
+		uint64_t card_addr:32;
+#else
+		uint64_t card_addr:32;
+		uint64_t block_cnt:16;
+		uint64_t multi:1;
+		uint64_t rw:1;
+		uint64_t rel_wr:1;
+		uint64_t thres:6;
+		uint64_t dat_null:1;
+		uint64_t sector:1;
+		uint64_t dma_val:1;
+		uint64_t bus_id:2;
+		uint64_t reserved_62_63:2;
+#endif
+	} s;
+};
+
+union cvmx_mio_emm_int {
+	uint64_t u64;
+	struct cvmx_mio_emm_int_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t switch_err:1;
+		uint64_t switch_done:1;
+		uint64_t dma_err:1;
+		uint64_t cmd_err:1;
+		uint64_t dma_done:1;
+		uint64_t cmd_done:1;
+		uint64_t buf_done:1;
+#else
+		uint64_t buf_done:1;
+		uint64_t cmd_done:1;
+		uint64_t dma_done:1;
+		uint64_t cmd_err:1;
+		uint64_t dma_err:1;
+		uint64_t switch_done:1;
+		uint64_t switch_err:1;
+		uint64_t reserved_7_63:57;
+#endif
+	} s;
+};
+
+union cvmx_mio_emm_int_en {
+	uint64_t u64;
+	struct cvmx_mio_emm_int_en_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t switch_err:1;
+		uint64_t switch_done:1;
+		uint64_t dma_err:1;
+		uint64_t cmd_err:1;
+		uint64_t dma_done:1;
+		uint64_t cmd_done:1;
+		uint64_t buf_done:1;
+#else
+		uint64_t buf_done:1;
+		uint64_t cmd_done:1;
+		uint64_t dma_done:1;
+		uint64_t cmd_err:1;
+		uint64_t dma_err:1;
+		uint64_t switch_done:1;
+		uint64_t switch_err:1;
+		uint64_t reserved_7_63:57;
+#endif
+	} s;
+};
+
+union cvmx_mio_emm_modex {
+	uint64_t u64;
+	struct cvmx_mio_emm_modex_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_49_63:15;
+		uint64_t hs_timing:1;
+		uint64_t reserved_43_47:5;
+		uint64_t bus_width:3;
+		uint64_t reserved_36_39:4;
+		uint64_t power_class:4;
+		uint64_t clk_hi:16;
+		uint64_t clk_lo:16;
+#else
+		uint64_t clk_lo:16;
+		uint64_t clk_hi:16;
+		uint64_t power_class:4;
+		uint64_t reserved_36_39:4;
+		uint64_t bus_width:3;
+		uint64_t reserved_43_47:5;
+		uint64_t hs_timing:1;
+		uint64_t reserved_49_63:15;
+#endif
+	} s;
+};
+
+union cvmx_mio_emm_rca {
+	uint64_t u64;
+	struct cvmx_mio_emm_rca_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t card_rca:16;
+#else
+		uint64_t card_rca:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_mio_emm_rsp_hi {
+	uint64_t u64;
+	struct cvmx_mio_emm_rsp_hi_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t dat:64;
+#else
+		uint64_t dat:64;
+#endif
+	} s;
+};
+
+union cvmx_mio_emm_rsp_lo {
+	uint64_t u64;
+	struct cvmx_mio_emm_rsp_lo_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t dat:64;
+#else
+		uint64_t dat:64;
+#endif
+	} s;
+};
+
+union cvmx_mio_emm_rsp_sts {
+	uint64_t u64;
+	struct cvmx_mio_emm_rsp_sts_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_62_63:2;
+		uint64_t bus_id:2;
+		uint64_t cmd_val:1;
+		uint64_t switch_val:1;
+		uint64_t dma_val:1;
+		uint64_t dma_pend:1;
+		uint64_t reserved_29_55:27;
+		uint64_t dbuf_err:1;
+		uint64_t reserved_24_27:4;
+		uint64_t dbuf:1;
+		uint64_t blk_timeout:1;
+		uint64_t blk_crc_err:1;
+		uint64_t rsp_busybit:1;
+		uint64_t stp_timeout:1;
+		uint64_t stp_crc_err:1;
+		uint64_t stp_bad_sts:1;
+		uint64_t stp_val:1;
+		uint64_t rsp_timeout:1;
+		uint64_t rsp_crc_err:1;
+		uint64_t rsp_bad_sts:1;
+		uint64_t rsp_val:1;
+		uint64_t rsp_type:3;
+		uint64_t cmd_type:2;
+		uint64_t cmd_idx:6;
+		uint64_t cmd_done:1;
+#else
+		uint64_t cmd_done:1;
+		uint64_t cmd_idx:6;
+		uint64_t cmd_type:2;
+		uint64_t rsp_type:3;
+		uint64_t rsp_val:1;
+		uint64_t rsp_bad_sts:1;
+		uint64_t rsp_crc_err:1;
+		uint64_t rsp_timeout:1;
+		uint64_t stp_val:1;
+		uint64_t stp_bad_sts:1;
+		uint64_t stp_crc_err:1;
+		uint64_t stp_timeout:1;
+		uint64_t rsp_busybit:1;
+		uint64_t blk_crc_err:1;
+		uint64_t blk_timeout:1;
+		uint64_t dbuf:1;
+		uint64_t reserved_24_27:4;
+		uint64_t dbuf_err:1;
+		uint64_t reserved_29_55:27;
+		uint64_t dma_pend:1;
+		uint64_t dma_val:1;
+		uint64_t switch_val:1;
+		uint64_t cmd_val:1;
+		uint64_t bus_id:2;
+		uint64_t reserved_62_63:2;
+#endif
+	} s;
+};
+
+union cvmx_mio_emm_sample {
+	uint64_t u64;
+	struct cvmx_mio_emm_sample_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_26_63:38;
+		uint64_t cmd_cnt:10;
+		uint64_t reserved_10_15:6;
+		uint64_t dat_cnt:10;
+#else
+		uint64_t dat_cnt:10;
+		uint64_t reserved_10_15:6;
+		uint64_t cmd_cnt:10;
+		uint64_t reserved_26_63:38;
+#endif
+	} s;
+};
+
+union cvmx_mio_emm_sts_mask {
+	uint64_t u64;
+	struct cvmx_mio_emm_sts_mask_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t sts_msk:32;
+#else
+		uint64_t sts_msk:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_mio_emm_switch {
+	uint64_t u64;
+	struct cvmx_mio_emm_switch_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_62_63:2;
+		uint64_t bus_id:2;
+		uint64_t switch_exe:1;
+		uint64_t switch_err0:1;
+		uint64_t switch_err1:1;
+		uint64_t switch_err2:1;
+		uint64_t reserved_49_55:7;
+		uint64_t hs_timing:1;
+		uint64_t reserved_43_47:5;
+		uint64_t bus_width:3;
+		uint64_t reserved_36_39:4;
+		uint64_t power_class:4;
+		uint64_t clk_hi:16;
+		uint64_t clk_lo:16;
+#else
+		uint64_t clk_lo:16;
+		uint64_t clk_hi:16;
+		uint64_t power_class:4;
+		uint64_t reserved_36_39:4;
+		uint64_t bus_width:3;
+		uint64_t reserved_43_47:5;
+		uint64_t hs_timing:1;
+		uint64_t reserved_49_55:7;
+		uint64_t switch_err2:1;
+		uint64_t switch_err1:1;
+		uint64_t switch_err0:1;
+		uint64_t switch_exe:1;
+		uint64_t bus_id:2;
+		uint64_t reserved_62_63:2;
+#endif
+	} s;
+};
+
+union cvmx_mio_emm_wdog {
+	uint64_t u64;
+	struct cvmx_mio_emm_wdog_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_26_63:38;
+		uint64_t clk_cnt:26;
+#else
+		uint64_t clk_cnt:26;
+		uint64_t reserved_26_63:38;
+#endif
+	} s;
+};
+
+union cvmx_mio_fus_bnk_datx {
+	uint64_t u64;
+	struct cvmx_mio_fus_bnk_datx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t dat:64;
+#else
+		uint64_t dat:64;
+#endif
+	} s;
+};
+
+union cvmx_mio_fus_dat0 {
+	uint64_t u64;
+	struct cvmx_mio_fus_dat0_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t man_info:32;
+#else
+		uint64_t man_info:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_mio_fus_dat1 {
+	uint64_t u64;
+	struct cvmx_mio_fus_dat1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t man_info:32;
+#else
+		uint64_t man_info:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_mio_fus_dat2 {
+	uint64_t u64;
+	struct cvmx_mio_fus_dat2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_59_63:5;
+		uint64_t run_platform:3;
+		uint64_t gbl_pwr_throttle:8;
+		uint64_t fus118:1;
+		uint64_t rom_info:10;
+		uint64_t power_limit:2;
+		uint64_t dorm_crypto:1;
+		uint64_t fus318:1;
+		uint64_t raid_en:1;
+		uint64_t reserved_30_31:2;
+		uint64_t nokasu:1;
+		uint64_t nodfa_cp2:1;
+		uint64_t nomul:1;
+		uint64_t nocrypto:1;
+		uint64_t rst_sht:1;
+		uint64_t bist_dis:1;
+		uint64_t chip_id:8;
+		uint64_t reserved_0_15:16;
+#else
+		uint64_t reserved_0_15:16;
+		uint64_t chip_id:8;
+		uint64_t bist_dis:1;
+		uint64_t rst_sht:1;
+		uint64_t nocrypto:1;
+		uint64_t nomul:1;
+		uint64_t nodfa_cp2:1;
+		uint64_t nokasu:1;
+		uint64_t reserved_30_31:2;
+		uint64_t raid_en:1;
+		uint64_t fus318:1;
+		uint64_t dorm_crypto:1;
+		uint64_t power_limit:2;
+		uint64_t rom_info:10;
+		uint64_t fus118:1;
+		uint64_t gbl_pwr_throttle:8;
+		uint64_t run_platform:3;
+		uint64_t reserved_59_63:5;
+#endif
+	} s;
+	struct cvmx_mio_fus_dat2_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t nodfa_cp2:1;
+		uint64_t nomul:1;
+		uint64_t nocrypto:1;
+		uint64_t rst_sht:1;
+		uint64_t bist_dis:1;
+		uint64_t chip_id:8;
+		uint64_t pll_off:4;
+		uint64_t reserved_1_11:11;
+		uint64_t pp_dis:1;
+#else
+		uint64_t pp_dis:1;
+		uint64_t reserved_1_11:11;
+		uint64_t pll_off:4;
+		uint64_t chip_id:8;
+		uint64_t bist_dis:1;
+		uint64_t rst_sht:1;
+		uint64_t nocrypto:1;
+		uint64_t nomul:1;
+		uint64_t nodfa_cp2:1;
+		uint64_t reserved_29_63:35;
+#endif
+	} cn30xx;
+	struct cvmx_mio_fus_dat2_cn31xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t nodfa_cp2:1;
+		uint64_t nomul:1;
+		uint64_t nocrypto:1;
+		uint64_t rst_sht:1;
+		uint64_t bist_dis:1;
+		uint64_t chip_id:8;
+		uint64_t pll_off:4;
+		uint64_t reserved_2_11:10;
+		uint64_t pp_dis:2;
+#else
+		uint64_t pp_dis:2;
+		uint64_t reserved_2_11:10;
+		uint64_t pll_off:4;
+		uint64_t chip_id:8;
+		uint64_t bist_dis:1;
+		uint64_t rst_sht:1;
+		uint64_t nocrypto:1;
+		uint64_t nomul:1;
+		uint64_t nodfa_cp2:1;
+		uint64_t reserved_29_63:35;
+#endif
+	} cn31xx;
+	struct cvmx_mio_fus_dat2_cn38xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t nodfa_cp2:1;
+		uint64_t nomul:1;
+		uint64_t nocrypto:1;
+		uint64_t rst_sht:1;
+		uint64_t bist_dis:1;
+		uint64_t chip_id:8;
+		uint64_t pp_dis:16;
+#else
+		uint64_t pp_dis:16;
+		uint64_t chip_id:8;
+		uint64_t bist_dis:1;
+		uint64_t rst_sht:1;
+		uint64_t nocrypto:1;
+		uint64_t nomul:1;
+		uint64_t nodfa_cp2:1;
+		uint64_t reserved_29_63:35;
+#endif
+	} cn38xx;
+	struct cvmx_mio_fus_dat2_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_34_63:30;
+		uint64_t fus318:1;
+		uint64_t raid_en:1;
+		uint64_t reserved_30_31:2;
+		uint64_t nokasu:1;
+		uint64_t nodfa_cp2:1;
+		uint64_t nomul:1;
+		uint64_t nocrypto:1;
+		uint64_t rst_sht:1;
+		uint64_t bist_dis:1;
+		uint64_t chip_id:8;
+		uint64_t reserved_2_15:14;
+		uint64_t pp_dis:2;
+#else
+		uint64_t pp_dis:2;
+		uint64_t reserved_2_15:14;
+		uint64_t chip_id:8;
+		uint64_t bist_dis:1;
+		uint64_t rst_sht:1;
+		uint64_t nocrypto:1;
+		uint64_t nomul:1;
+		uint64_t nodfa_cp2:1;
+		uint64_t nokasu:1;
+		uint64_t reserved_30_31:2;
+		uint64_t raid_en:1;
+		uint64_t fus318:1;
+		uint64_t reserved_34_63:30;
+#endif
+	} cn50xx;
+	struct cvmx_mio_fus_dat2_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_34_63:30;
+		uint64_t fus318:1;
+		uint64_t raid_en:1;
+		uint64_t reserved_30_31:2;
+		uint64_t nokasu:1;
+		uint64_t nodfa_cp2:1;
+		uint64_t nomul:1;
+		uint64_t nocrypto:1;
+		uint64_t rst_sht:1;
+		uint64_t bist_dis:1;
+		uint64_t chip_id:8;
+		uint64_t reserved_4_15:12;
+		uint64_t pp_dis:4;
+#else
+		uint64_t pp_dis:4;
+		uint64_t reserved_4_15:12;
+		uint64_t chip_id:8;
+		uint64_t bist_dis:1;
+		uint64_t rst_sht:1;
+		uint64_t nocrypto:1;
+		uint64_t nomul:1;
+		uint64_t nodfa_cp2:1;
+		uint64_t nokasu:1;
+		uint64_t reserved_30_31:2;
+		uint64_t raid_en:1;
+		uint64_t fus318:1;
+		uint64_t reserved_34_63:30;
+#endif
+	} cn52xx;
+	struct cvmx_mio_fus_dat2_cn56xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_34_63:30;
+		uint64_t fus318:1;
+		uint64_t raid_en:1;
+		uint64_t reserved_30_31:2;
+		uint64_t nokasu:1;
+		uint64_t nodfa_cp2:1;
+		uint64_t nomul:1;
+		uint64_t nocrypto:1;
+		uint64_t rst_sht:1;
+		uint64_t bist_dis:1;
+		uint64_t chip_id:8;
+		uint64_t reserved_12_15:4;
+		uint64_t pp_dis:12;
+#else
+		uint64_t pp_dis:12;
+		uint64_t reserved_12_15:4;
+		uint64_t chip_id:8;
+		uint64_t bist_dis:1;
+		uint64_t rst_sht:1;
+		uint64_t nocrypto:1;
+		uint64_t nomul:1;
+		uint64_t nodfa_cp2:1;
+		uint64_t nokasu:1;
+		uint64_t reserved_30_31:2;
+		uint64_t raid_en:1;
+		uint64_t fus318:1;
+		uint64_t reserved_34_63:30;
+#endif
+	} cn56xx;
+	struct cvmx_mio_fus_dat2_cn58xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_30_63:34;
+		uint64_t nokasu:1;
+		uint64_t nodfa_cp2:1;
+		uint64_t nomul:1;
+		uint64_t nocrypto:1;
+		uint64_t rst_sht:1;
+		uint64_t bist_dis:1;
+		uint64_t chip_id:8;
+		uint64_t pp_dis:16;
+#else
+		uint64_t pp_dis:16;
+		uint64_t chip_id:8;
+		uint64_t bist_dis:1;
+		uint64_t rst_sht:1;
+		uint64_t nocrypto:1;
+		uint64_t nomul:1;
+		uint64_t nodfa_cp2:1;
+		uint64_t nokasu:1;
+		uint64_t reserved_30_63:34;
+#endif
+	} cn58xx;
+	struct cvmx_mio_fus_dat2_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t fus118:1;
+		uint64_t rom_info:10;
+		uint64_t power_limit:2;
+		uint64_t dorm_crypto:1;
+		uint64_t fus318:1;
+		uint64_t raid_en:1;
+		uint64_t reserved_29_31:3;
+		uint64_t nodfa_cp2:1;
+		uint64_t nomul:1;
+		uint64_t nocrypto:1;
+		uint64_t reserved_24_25:2;
+		uint64_t chip_id:8;
+		uint64_t reserved_4_15:12;
+		uint64_t pp_dis:4;
+#else
+		uint64_t pp_dis:4;
+		uint64_t reserved_4_15:12;
+		uint64_t chip_id:8;
+		uint64_t reserved_24_25:2;
+		uint64_t nocrypto:1;
+		uint64_t nomul:1;
+		uint64_t nodfa_cp2:1;
+		uint64_t reserved_29_31:3;
+		uint64_t raid_en:1;
+		uint64_t fus318:1;
+		uint64_t dorm_crypto:1;
+		uint64_t power_limit:2;
+		uint64_t rom_info:10;
+		uint64_t fus118:1;
+		uint64_t reserved_48_63:16;
+#endif
+	} cn61xx;
+	struct cvmx_mio_fus_dat2_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_35_63:29;
+		uint64_t dorm_crypto:1;
+		uint64_t fus318:1;
+		uint64_t raid_en:1;
+		uint64_t reserved_29_31:3;
+		uint64_t nodfa_cp2:1;
+		uint64_t nomul:1;
+		uint64_t nocrypto:1;
+		uint64_t reserved_24_25:2;
+		uint64_t chip_id:8;
+		uint64_t reserved_6_15:10;
+		uint64_t pp_dis:6;
+#else
+		uint64_t pp_dis:6;
+		uint64_t reserved_6_15:10;
+		uint64_t chip_id:8;
+		uint64_t reserved_24_25:2;
+		uint64_t nocrypto:1;
+		uint64_t nomul:1;
+		uint64_t nodfa_cp2:1;
+		uint64_t reserved_29_31:3;
+		uint64_t raid_en:1;
+		uint64_t fus318:1;
+		uint64_t dorm_crypto:1;
+		uint64_t reserved_35_63:29;
+#endif
+	} cn63xx;
+	struct cvmx_mio_fus_dat2_cn66xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t fus118:1;
+		uint64_t rom_info:10;
+		uint64_t power_limit:2;
+		uint64_t dorm_crypto:1;
+		uint64_t fus318:1;
+		uint64_t raid_en:1;
+		uint64_t reserved_29_31:3;
+		uint64_t nodfa_cp2:1;
+		uint64_t nomul:1;
+		uint64_t nocrypto:1;
+		uint64_t reserved_24_25:2;
+		uint64_t chip_id:8;
+		uint64_t reserved_10_15:6;
+		uint64_t pp_dis:10;
+#else
+		uint64_t pp_dis:10;
+		uint64_t reserved_10_15:6;
+		uint64_t chip_id:8;
+		uint64_t reserved_24_25:2;
+		uint64_t nocrypto:1;
+		uint64_t nomul:1;
+		uint64_t nodfa_cp2:1;
+		uint64_t reserved_29_31:3;
+		uint64_t raid_en:1;
+		uint64_t fus318:1;
+		uint64_t dorm_crypto:1;
+		uint64_t power_limit:2;
+		uint64_t rom_info:10;
+		uint64_t fus118:1;
+		uint64_t reserved_48_63:16;
+#endif
+	} cn66xx;
+	struct cvmx_mio_fus_dat2_cn68xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_37_63:27;
+		uint64_t power_limit:2;
+		uint64_t dorm_crypto:1;
+		uint64_t fus318:1;
+		uint64_t raid_en:1;
+		uint64_t reserved_29_31:3;
+		uint64_t nodfa_cp2:1;
+		uint64_t nomul:1;
+		uint64_t nocrypto:1;
+		uint64_t reserved_24_25:2;
+		uint64_t chip_id:8;
+		uint64_t reserved_0_15:16;
+#else
+		uint64_t reserved_0_15:16;
+		uint64_t chip_id:8;
+		uint64_t reserved_24_25:2;
+		uint64_t nocrypto:1;
+		uint64_t nomul:1;
+		uint64_t nodfa_cp2:1;
+		uint64_t reserved_29_31:3;
+		uint64_t raid_en:1;
+		uint64_t fus318:1;
+		uint64_t dorm_crypto:1;
+		uint64_t power_limit:2;
+		uint64_t reserved_37_63:27;
+#endif
+	} cn68xx;
+	struct cvmx_mio_fus_dat2_cn70xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t fus118:1;
+		uint64_t rom_info:10;
+		uint64_t power_limit:2;
+		uint64_t dorm_crypto:1;
+		uint64_t fus318:1;
+		uint64_t raid_en:1;
+		uint64_t reserved_31_29:3;
+		uint64_t nodfa_cp2:1;
+		uint64_t nomul:1;
+		uint64_t nocrypto:1;
+		uint64_t reserved_25_24:2;
+		uint64_t chip_id:8;
+		uint64_t reserved_15_0:16;
+#else
+		uint64_t reserved_15_0:16;
+		uint64_t chip_id:8;
+		uint64_t reserved_25_24:2;
+		uint64_t nocrypto:1;
+		uint64_t nomul:1;
+		uint64_t nodfa_cp2:1;
+		uint64_t reserved_31_29:3;
+		uint64_t raid_en:1;
+		uint64_t fus318:1;
+		uint64_t dorm_crypto:1;
+		uint64_t power_limit:2;
+		uint64_t rom_info:10;
+		uint64_t fus118:1;
+		uint64_t reserved_48_63:16;
+#endif
+	} cn70xx;
+	struct cvmx_mio_fus_dat2_cn73xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_59_63:5;
+		uint64_t run_platform:3;
+		uint64_t gbl_pwr_throttle:8;
+		uint64_t fus118:1;
+		uint64_t rom_info:10;
+		uint64_t power_limit:2;
+		uint64_t dorm_crypto:1;
+		uint64_t fus318:1;
+		uint64_t raid_en:1;
+		uint64_t reserved_31_29:3;
+		uint64_t nodfa_cp2:1;
+		uint64_t nomul:1;
+		uint64_t nocrypto:1;
+		uint64_t reserved_25_24:2;
+		uint64_t chip_id:8;
+		uint64_t reserved_15_0:16;
+#else
+		uint64_t reserved_15_0:16;
+		uint64_t chip_id:8;
+		uint64_t reserved_25_24:2;
+		uint64_t nocrypto:1;
+		uint64_t nomul:1;
+		uint64_t nodfa_cp2:1;
+		uint64_t reserved_31_29:3;
+		uint64_t raid_en:1;
+		uint64_t fus318:1;
+		uint64_t dorm_crypto:1;
+		uint64_t power_limit:2;
+		uint64_t rom_info:10;
+		uint64_t fus118:1;
+		uint64_t gbl_pwr_throttle:8;
+		uint64_t run_platform:3;
+		uint64_t reserved_59_63:5;
+#endif
+	} cn73xx;
+	struct cvmx_mio_fus_dat2_cn78xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_59_63:5;
+		uint64_t run_platform:3;
+		uint64_t reserved_48_55:8;
+		uint64_t fus118:1;
+		uint64_t rom_info:10;
+		uint64_t power_limit:2;
+		uint64_t dorm_crypto:1;
+		uint64_t fus318:1;
+		uint64_t raid_en:1;
+		uint64_t reserved_31_29:3;
+		uint64_t nodfa_cp2:1;
+		uint64_t nomul:1;
+		uint64_t nocrypto:1;
+		uint64_t reserved_25_24:2;
+		uint64_t chip_id:8;
+		uint64_t reserved_0_15:16;
+#else
+		uint64_t reserved_0_15:16;
+		uint64_t chip_id:8;
+		uint64_t reserved_25_24:2;
+		uint64_t nocrypto:1;
+		uint64_t nomul:1;
+		uint64_t nodfa_cp2:1;
+		uint64_t reserved_31_29:3;
+		uint64_t raid_en:1;
+		uint64_t fus318:1;
+		uint64_t dorm_crypto:1;
+		uint64_t power_limit:2;
+		uint64_t rom_info:10;
+		uint64_t fus118:1;
+		uint64_t reserved_48_55:8;
+		uint64_t run_platform:3;
+		uint64_t reserved_59_63:5;
+#endif
+	} cn78xx;
+	struct cvmx_mio_fus_dat2_cn78xxp2 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_59_63:5;
+		uint64_t run_platform:3;
+		uint64_t gbl_pwr_throttle:8;
+		uint64_t fus118:1;
+		uint64_t rom_info:10;
+		uint64_t power_limit:2;
+		uint64_t dorm_crypto:1;
+		uint64_t fus318:1;
+		uint64_t raid_en:1;
+		uint64_t reserved_31_29:3;
+		uint64_t nodfa_cp2:1;
+		uint64_t nomul:1;
+		uint64_t nocrypto:1;
+		uint64_t reserved_25_24:2;
+		uint64_t chip_id:8;
+		uint64_t reserved_0_15:16;
+#else
+		uint64_t reserved_0_15:16;
+		uint64_t chip_id:8;
+		uint64_t reserved_25_24:2;
+		uint64_t nocrypto:1;
+		uint64_t nomul:1;
+		uint64_t nodfa_cp2:1;
+		uint64_t reserved_31_29:3;
+		uint64_t raid_en:1;
+		uint64_t fus318:1;
+		uint64_t dorm_crypto:1;
+		uint64_t power_limit:2;
+		uint64_t rom_info:10;
+		uint64_t fus118:1;
+		uint64_t gbl_pwr_throttle:8;
+		uint64_t run_platform:3;
+		uint64_t reserved_59_63:5;
+#endif
+	} cn78xxp2;
+};
+
+union cvmx_mio_fus_dat3 {
+	uint64_t u64;
+	struct cvmx_mio_fus_dat3_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t ema0:6;
+		uint64_t pll_ctl:10;
+		uint64_t dfa_info_dte:3;
+		uint64_t dfa_info_clm:4;
+		uint64_t pll_alt_matrix:1;
+		uint64_t reserved_38_39:2;
+		uint64_t efus_lck_rsv:1;
+		uint64_t efus_lck_man:1;
+		uint64_t pll_half_dis:1;
+		uint64_t l2c_crip:3;
+		uint64_t reserved_28_31:4;
+		uint64_t efus_lck:1;
+		uint64_t efus_ign:1;
+		uint64_t nozip:1;
+		uint64_t nodfa_dte:1;
+		uint64_t reserved_0_23:24;
+#else
+		uint64_t reserved_0_23:24;
+		uint64_t nodfa_dte:1;
+		uint64_t nozip:1;
+		uint64_t efus_ign:1;
+		uint64_t efus_lck:1;
+		uint64_t reserved_28_31:4;
+		uint64_t l2c_crip:3;
+		uint64_t pll_half_dis:1;
+		uint64_t efus_lck_man:1;
+		uint64_t efus_lck_rsv:1;
+		uint64_t reserved_38_39:2;
+		uint64_t pll_alt_matrix:1;
+		uint64_t dfa_info_clm:4;
+		uint64_t dfa_info_dte:3;
+		uint64_t pll_ctl:10;
+		uint64_t ema0:6;
+#endif
+	} s;
+	struct cvmx_mio_fus_dat3_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t pll_div4:1;
+		uint64_t reserved_29_30:2;
+		uint64_t bar2_en:1;
+		uint64_t efus_lck:1;
+		uint64_t efus_ign:1;
+		uint64_t nozip:1;
+		uint64_t nodfa_dte:1;
+		uint64_t icache:24;
+#else
+		uint64_t icache:24;
+		uint64_t nodfa_dte:1;
+		uint64_t nozip:1;
+		uint64_t efus_ign:1;
+		uint64_t efus_lck:1;
+		uint64_t bar2_en:1;
+		uint64_t reserved_29_30:2;
+		uint64_t pll_div4:1;
+		uint64_t reserved_32_63:32;
+#endif
+	} cn30xx;
+	struct cvmx_mio_fus_dat3_cn31xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t pll_div4:1;
+		uint64_t zip_crip:2;
+		uint64_t bar2_en:1;
+		uint64_t efus_lck:1;
+		uint64_t efus_ign:1;
+		uint64_t nozip:1;
+		uint64_t nodfa_dte:1;
+		uint64_t icache:24;
+#else
+		uint64_t icache:24;
+		uint64_t nodfa_dte:1;
+		uint64_t nozip:1;
+		uint64_t efus_ign:1;
+		uint64_t efus_lck:1;
+		uint64_t bar2_en:1;
+		uint64_t zip_crip:2;
+		uint64_t pll_div4:1;
+		uint64_t reserved_32_63:32;
+#endif
+	} cn31xx;
+	struct cvmx_mio_fus_dat3_cn38xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_31_63:33;
+		uint64_t zip_crip:2;
+		uint64_t bar2_en:1;
+		uint64_t efus_lck:1;
+		uint64_t efus_ign:1;
+		uint64_t nozip:1;
+		uint64_t nodfa_dte:1;
+		uint64_t icache:24;
+#else
+		uint64_t icache:24;
+		uint64_t nodfa_dte:1;
+		uint64_t nozip:1;
+		uint64_t efus_ign:1;
+		uint64_t efus_lck:1;
+		uint64_t bar2_en:1;
+		uint64_t zip_crip:2;
+		uint64_t reserved_31_63:33;
+#endif
+	} cn38xx;
+	struct cvmx_mio_fus_dat3_cn38xxp2 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t bar2_en:1;
+		uint64_t efus_lck:1;
+		uint64_t efus_ign:1;
+		uint64_t nozip:1;
+		uint64_t nodfa_dte:1;
+		uint64_t icache:24;
+#else
+		uint64_t icache:24;
+		uint64_t nodfa_dte:1;
+		uint64_t nozip:1;
+		uint64_t efus_ign:1;
+		uint64_t efus_lck:1;
+		uint64_t bar2_en:1;
+		uint64_t reserved_29_63:35;
+#endif
+	} cn38xxp2;
+	struct cvmx_mio_fus_dat3_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_58_63:6;
+		uint64_t pll_ctl:10;
+		uint64_t dfa_info_dte:3;
+		uint64_t dfa_info_clm:4;
+		uint64_t reserved_40_40:1;
+		uint64_t ema:2;
+		uint64_t efus_lck_rsv:1;
+		uint64_t efus_lck_man:1;
+		uint64_t pll_half_dis:1;
+		uint64_t l2c_crip:3;
+		uint64_t reserved_31_31:1;
+		uint64_t zip_info:2;
+		uint64_t bar2_en:1;
+		uint64_t efus_lck:1;
+		uint64_t efus_ign:1;
+		uint64_t nozip:1;
+		uint64_t nodfa_dte:1;
+		uint64_t reserved_0_23:24;
+#else
+		uint64_t reserved_0_23:24;
+		uint64_t nodfa_dte:1;
+		uint64_t nozip:1;
+		uint64_t efus_ign:1;
+		uint64_t efus_lck:1;
+		uint64_t bar2_en:1;
+		uint64_t zip_info:2;
+		uint64_t reserved_31_31:1;
+		uint64_t l2c_crip:3;
+		uint64_t pll_half_dis:1;
+		uint64_t efus_lck_man:1;
+		uint64_t efus_lck_rsv:1;
+		uint64_t ema:2;
+		uint64_t reserved_40_40:1;
+		uint64_t dfa_info_clm:4;
+		uint64_t dfa_info_dte:3;
+		uint64_t pll_ctl:10;
+		uint64_t reserved_58_63:6;
+#endif
+	} cn61xx;
+	struct cvmx_mio_fus_dat3_cn70xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t ema0:6;
+		uint64_t pll_ctl:10;
+		uint64_t dfa_info_dte:3;
+		uint64_t dfa_info_clm:4;
+		uint64_t pll_alt_matrix:1;
+		uint64_t pll_bwadj_denom:2;
+		uint64_t efus_lck_rsv:1;
+		uint64_t efus_lck_man:1;
+		uint64_t pll_half_dis:1;
+		uint64_t l2c_crip:3;
+		uint64_t use_int_refclk:1;
+		uint64_t zip_info:2;
+		uint64_t bar2_sz_conf:1;
+		uint64_t efus_lck:1;
+		uint64_t efus_ign:1;
+		uint64_t nozip:1;
+		uint64_t nodfa_dte:1;
+		uint64_t ema1:6;
+		uint64_t reserved_0_17:18;
+#else
+		uint64_t reserved_0_17:18;
+		uint64_t ema1:6;
+		uint64_t nodfa_dte:1;
+		uint64_t nozip:1;
+		uint64_t efus_ign:1;
+		uint64_t efus_lck:1;
+		uint64_t bar2_sz_conf:1;
+		uint64_t zip_info:2;
+		uint64_t use_int_refclk:1;
+		uint64_t l2c_crip:3;
+		uint64_t pll_half_dis:1;
+		uint64_t efus_lck_man:1;
+		uint64_t efus_lck_rsv:1;
+		uint64_t pll_bwadj_denom:2;
+		uint64_t pll_alt_matrix:1;
+		uint64_t dfa_info_clm:4;
+		uint64_t dfa_info_dte:3;
+		uint64_t pll_ctl:10;
+		uint64_t ema0:6;
+#endif
+	} cn70xx;
+	struct cvmx_mio_fus_dat3_cn70xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t ema0:6;
+		uint64_t pll_ctl:10;
+		uint64_t dfa_info_dte:3;
+		uint64_t dfa_info_clm:4;
+		uint64_t reserved_38_40:3;
+		uint64_t efus_lck_rsv:1;
+		uint64_t efus_lck_man:1;
+		uint64_t pll_half_dis:1;
+		uint64_t l2c_crip:3;
+		uint64_t reserved_31_31:1;
+		uint64_t zip_info:2;
+		uint64_t bar2_sz_conf:1;
+		uint64_t efus_lck:1;
+		uint64_t efus_ign:1;
+		uint64_t nozip:1;
+		uint64_t nodfa_dte:1;
+		uint64_t ema1:6;
+		uint64_t reserved_0_17:18;
+#else
+		uint64_t reserved_0_17:18;
+		uint64_t ema1:6;
+		uint64_t nodfa_dte:1;
+		uint64_t nozip:1;
+		uint64_t efus_ign:1;
+		uint64_t efus_lck:1;
+		uint64_t bar2_sz_conf:1;
+		uint64_t zip_info:2;
+		uint64_t reserved_31_31:1;
+		uint64_t l2c_crip:3;
+		uint64_t pll_half_dis:1;
+		uint64_t efus_lck_man:1;
+		uint64_t efus_lck_rsv:1;
+		uint64_t reserved_38_40:3;
+		uint64_t dfa_info_clm:4;
+		uint64_t dfa_info_dte:3;
+		uint64_t pll_ctl:10;
+		uint64_t ema0:6;
+#endif
+	} cn70xxp1;
+	struct cvmx_mio_fus_dat3_cn73xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t ema0:6;
+		uint64_t pll_ctl:10;
+		uint64_t dfa_info_dte:3;
+		uint64_t dfa_info_clm:4;
+		uint64_t pll_alt_matrix:1;
+		uint64_t pll_bwadj_denom:2;
+		uint64_t efus_lck_rsv:1;
+		uint64_t efus_lck_man:1;
+		uint64_t pll_half_dis:1;
+		uint64_t l2c_crip:3;
+		uint64_t use_int_refclk:1;
+		uint64_t zip_info:2;
+		uint64_t bar2_sz_conf:1;
+		uint64_t efus_lck:1;
+		uint64_t efus_ign:1;
+		uint64_t nozip:1;
+		uint64_t nodfa_dte:1;
+		uint64_t ema1:6;
+		uint64_t nohna_dte:1;
+		uint64_t hna_info_dte:3;
+		uint64_t hna_info_clm:4;
+		uint64_t reserved_9_9:1;
+		uint64_t core_pll_mul:5;
+		uint64_t pnr_pll_mul:4;
+#else
+		uint64_t pnr_pll_mul:4;
+		uint64_t core_pll_mul:5;
+		uint64_t reserved_9_9:1;
+		uint64_t hna_info_clm:4;
+		uint64_t hna_info_dte:3;
+		uint64_t nohna_dte:1;
+		uint64_t ema1:6;
+		uint64_t nodfa_dte:1;
+		uint64_t nozip:1;
+		uint64_t efus_ign:1;
+		uint64_t efus_lck:1;
+		uint64_t bar2_sz_conf:1;
+		uint64_t zip_info:2;
+		uint64_t use_int_refclk:1;
+		uint64_t l2c_crip:3;
+		uint64_t pll_half_dis:1;
+		uint64_t efus_lck_man:1;
+		uint64_t efus_lck_rsv:1;
+		uint64_t pll_bwadj_denom:2;
+		uint64_t pll_alt_matrix:1;
+		uint64_t dfa_info_clm:4;
+		uint64_t dfa_info_dte:3;
+		uint64_t pll_ctl:10;
+		uint64_t ema0:6;
+#endif
+	} cn73xx;
+	struct cvmx_mio_fus_dat3_cn78xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t ema0:6;
+		uint64_t pll_ctl:10;
+		uint64_t dfa_info_dte:3;
+		uint64_t dfa_info_clm:4;
+		uint64_t reserved_38_40:3;
+		uint64_t efus_lck_rsv:1;
+		uint64_t efus_lck_man:1;
+		uint64_t pll_half_dis:1;
+		uint64_t l2c_crip:3;
+		uint64_t reserved_31_31:1;
+		uint64_t zip_info:2;
+		uint64_t bar2_sz_conf:1;
+		uint64_t efus_lck:1;
+		uint64_t efus_ign:1;
+		uint64_t nozip:1;
+		uint64_t nodfa_dte:1;
+		uint64_t ema1:6;
+		uint64_t nohna_dte:1;
+		uint64_t hna_info_dte:3;
+		uint64_t hna_info_clm:4;
+		uint64_t reserved_0_9:10;
+#else
+		uint64_t reserved_0_9:10;
+		uint64_t hna_info_clm:4;
+		uint64_t hna_info_dte:3;
+		uint64_t nohna_dte:1;
+		uint64_t ema1:6;
+		uint64_t nodfa_dte:1;
+		uint64_t nozip:1;
+		uint64_t efus_ign:1;
+		uint64_t efus_lck:1;
+		uint64_t bar2_sz_conf:1;
+		uint64_t zip_info:2;
+		uint64_t reserved_31_31:1;
+		uint64_t l2c_crip:3;
+		uint64_t pll_half_dis:1;
+		uint64_t efus_lck_man:1;
+		uint64_t efus_lck_rsv:1;
+		uint64_t reserved_38_40:3;
+		uint64_t dfa_info_clm:4;
+		uint64_t dfa_info_dte:3;
+		uint64_t pll_ctl:10;
+		uint64_t ema0:6;
+#endif
+	} cn78xx;
+	struct cvmx_mio_fus_dat3_cnf75xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t ema0:6;
+		uint64_t pll_ctl:10;
+		uint64_t dfa_info_dte:3;
+		uint64_t dfa_info_clm:4;
+		uint64_t pll_alt_matrix:1;
+		uint64_t pll_bwadj_denom:2;
+		uint64_t efus_lck_rsv:1;
+		uint64_t efus_lck_man:1;
+		uint64_t pll_half_dis:1;
+		uint64_t l2c_crip:3;
+		uint64_t use_int_refclk:1;
+		uint64_t zip_info:2;
+		uint64_t bar2_sz_conf:1;
+		uint64_t efus_lck:1;
+		uint64_t efus_ign:1;
+		uint64_t nozip:1;
+		uint64_t nodfa_dte:1;
+		uint64_t ema1:6;
+		uint64_t reserved_9_17:9;
+		uint64_t core_pll_mul:5;
+		uint64_t pnr_pll_mul:4;
+#else
+		uint64_t pnr_pll_mul:4;
+		uint64_t core_pll_mul:5;
+		uint64_t reserved_9_17:9;
+		uint64_t ema1:6;
+		uint64_t nodfa_dte:1;
+		uint64_t nozip:1;
+		uint64_t efus_ign:1;
+		uint64_t efus_lck:1;
+		uint64_t bar2_sz_conf:1;
+		uint64_t zip_info:2;
+		uint64_t use_int_refclk:1;
+		uint64_t l2c_crip:3;
+		uint64_t pll_half_dis:1;
+		uint64_t efus_lck_man:1;
+		uint64_t efus_lck_rsv:1;
+		uint64_t pll_bwadj_denom:2;
+		uint64_t pll_alt_matrix:1;
+		uint64_t dfa_info_clm:4;
+		uint64_t dfa_info_dte:3;
+		uint64_t pll_ctl:10;
+		uint64_t ema0:6;
+#endif
+	} cnf75xx;
+};
+
+union cvmx_mio_fus_ema {
+	uint64_t u64;
+	struct cvmx_mio_fus_ema_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t eff_ema:3;
+		uint64_t reserved_3_3:1;
+		uint64_t ema:3;
+#else
+		uint64_t ema:3;
+		uint64_t reserved_3_3:1;
+		uint64_t eff_ema:3;
+		uint64_t reserved_7_63:57;
+#endif
+	} s;
+	struct cvmx_mio_fus_ema_cn58xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t ema:2;
+#else
+		uint64_t ema:2;
+		uint64_t reserved_2_63:62;
+#endif
+	} cn58xx;
+};
+
+union cvmx_mio_fus_pdf {
+	uint64_t u64;
+	struct cvmx_mio_fus_pdf_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t pdf:64;
+#else
+		uint64_t pdf:64;
+#endif
+	} s;
+};
+
+union cvmx_mio_fus_pll {
+	uint64_t u64;
+	struct cvmx_mio_fus_pll_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t rclk_align_r:8;
+		uint64_t rclk_align_l:8;
+		uint64_t reserved_8_31:24;
+		uint64_t c_cout_rst:1;
+		uint64_t c_cout_sel:2;
+		uint64_t pnr_cout_rst:1;
+		uint64_t pnr_cout_sel:2;
+		uint64_t rfslip:1;
+		uint64_t fbslip:1;
+#else
+		uint64_t fbslip:1;
+		uint64_t rfslip:1;
+		uint64_t pnr_cout_sel:2;
+		uint64_t pnr_cout_rst:1;
+		uint64_t c_cout_sel:2;
+		uint64_t c_cout_rst:1;
+		uint64_t reserved_8_31:24;
+		uint64_t rclk_align_l:8;
+		uint64_t rclk_align_r:8;
+		uint64_t reserved_48_63:16;
+#endif
+	} s;
+	struct cvmx_mio_fus_pll_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t rfslip:1;
+		uint64_t fbslip:1;
+#else
+		uint64_t fbslip:1;
+		uint64_t rfslip:1;
+		uint64_t reserved_2_63:62;
+#endif
+	} cn50xx;
+	struct cvmx_mio_fus_pll_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t c_cout_rst:1;
+		uint64_t c_cout_sel:2;
+		uint64_t pnr_cout_rst:1;
+		uint64_t pnr_cout_sel:2;
+		uint64_t rfslip:1;
+		uint64_t fbslip:1;
+#else
+		uint64_t fbslip:1;
+		uint64_t rfslip:1;
+		uint64_t pnr_cout_sel:2;
+		uint64_t pnr_cout_rst:1;
+		uint64_t c_cout_sel:2;
+		uint64_t c_cout_rst:1;
+		uint64_t reserved_8_63:56;
+#endif
+	} cn61xx;
+};
+
+union cvmx_mio_fus_prog {
+	uint64_t u64;
+	struct cvmx_mio_fus_prog_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t soft:1;
+		uint64_t prog:1;
+#else
+		uint64_t prog:1;
+		uint64_t soft:1;
+		uint64_t reserved_2_63:62;
+#endif
+	} s;
+	struct cvmx_mio_fus_prog_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t prog:1;
+#else
+		uint64_t prog:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} cn30xx;
+};
+
+union cvmx_mio_fus_prog_times {
+	uint64_t u64;
+	struct cvmx_mio_fus_prog_times_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_35_63:29;
+		uint64_t vgate_pin:1;
+		uint64_t fsrc_pin:1;
+		uint64_t prog_pin:1;
+		uint64_t reserved_6_31:26;
+		uint64_t setup:6;
+#else
+		uint64_t setup:6;
+		uint64_t reserved_6_31:26;
+		uint64_t prog_pin:1;
+		uint64_t fsrc_pin:1;
+		uint64_t vgate_pin:1;
+		uint64_t reserved_35_63:29;
+#endif
+	} s;
+	struct cvmx_mio_fus_prog_times_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_33_63:31;
+		uint64_t prog_pin:1;
+		uint64_t out:8;
+		uint64_t sclk_lo:4;
+		uint64_t sclk_hi:12;
+		uint64_t setup:8;
+#else
+		uint64_t setup:8;
+		uint64_t sclk_hi:12;
+		uint64_t sclk_lo:4;
+		uint64_t out:8;
+		uint64_t prog_pin:1;
+		uint64_t reserved_33_63:31;
+#endif
+	} cn50xx;
+	struct cvmx_mio_fus_prog_times_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_35_63:29;
+		uint64_t vgate_pin:1;
+		uint64_t fsrc_pin:1;
+		uint64_t prog_pin:1;
+		uint64_t out:7;
+		uint64_t sclk_lo:4;
+		uint64_t sclk_hi:15;
+		uint64_t setup:6;
+#else
+		uint64_t setup:6;
+		uint64_t sclk_hi:15;
+		uint64_t sclk_lo:4;
+		uint64_t out:7;
+		uint64_t prog_pin:1;
+		uint64_t fsrc_pin:1;
+		uint64_t vgate_pin:1;
+		uint64_t reserved_35_63:29;
+#endif
+	} cn61xx;
+};
+
+union cvmx_mio_fus_rcmd {
+	uint64_t u64;
+	struct cvmx_mio_fus_rcmd_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_24_63:40;
+		uint64_t dat:8;
+		uint64_t reserved_13_15:3;
+		uint64_t pend:1;
+		uint64_t reserved_9_11:3;
+		uint64_t efuse:1;
+		uint64_t addr:8;
+#else
+		uint64_t addr:8;
+		uint64_t efuse:1;
+		uint64_t reserved_9_11:3;
+		uint64_t pend:1;
+		uint64_t reserved_13_15:3;
+		uint64_t dat:8;
+		uint64_t reserved_24_63:40;
+#endif
+	} s;
+	struct cvmx_mio_fus_rcmd_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_24_63:40;
+		uint64_t dat:8;
+		uint64_t reserved_13_15:3;
+		uint64_t pend:1;
+		uint64_t reserved_9_11:3;
+		uint64_t efuse:1;
+		uint64_t reserved_7_7:1;
+		uint64_t addr:7;
+#else
+		uint64_t addr:7;
+		uint64_t reserved_7_7:1;
+		uint64_t efuse:1;
+		uint64_t reserved_9_11:3;
+		uint64_t pend:1;
+		uint64_t reserved_13_15:3;
+		uint64_t dat:8;
+		uint64_t reserved_24_63:40;
+#endif
+	} cn30xx;
+};
+
+union cvmx_mio_fus_read_times {
+	uint64_t u64;
+	struct cvmx_mio_fus_read_times_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_26_63:38;
+		uint64_t sch:4;
+		uint64_t fsh:4;
+		uint64_t prh:4;
+		uint64_t sdh:4;
+		uint64_t setup:10;
+#else
+		uint64_t setup:10;
+		uint64_t sdh:4;
+		uint64_t prh:4;
+		uint64_t fsh:4;
+		uint64_t sch:4;
+		uint64_t reserved_26_63:38;
+#endif
+	} s;
+};
+
+union cvmx_mio_fus_repair_res0 {
+	uint64_t u64;
+	struct cvmx_mio_fus_repair_res0_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_55_63:9;
+		uint64_t too_many:1;
+		uint64_t repair2:18;
+		uint64_t repair1:18;
+		uint64_t repair0:18;
+#else
+		uint64_t repair0:18;
+		uint64_t repair1:18;
+		uint64_t repair2:18;
+		uint64_t too_many:1;
+		uint64_t reserved_55_63:9;
+#endif
+	} s;
+};
+
+union cvmx_mio_fus_repair_res1 {
+	uint64_t u64;
+	struct cvmx_mio_fus_repair_res1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_54_63:10;
+		uint64_t repair5:18;
+		uint64_t repair4:18;
+		uint64_t repair3:18;
+#else
+		uint64_t repair3:18;
+		uint64_t repair4:18;
+		uint64_t repair5:18;
+		uint64_t reserved_54_63:10;
+#endif
+	} s;
+};
+
+union cvmx_mio_fus_repair_res2 {
+	uint64_t u64;
+	struct cvmx_mio_fus_repair_res2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_18_63:46;
+		uint64_t repair6:18;
+#else
+		uint64_t repair6:18;
+		uint64_t reserved_18_63:46;
+#endif
+	} s;
+};
+
+union cvmx_mio_fus_spr_repair_res {
+	uint64_t u64;
+	struct cvmx_mio_fus_spr_repair_res_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_42_63:22;
+		uint64_t repair2:14;
+		uint64_t repair1:14;
+		uint64_t repair0:14;
+#else
+		uint64_t repair0:14;
+		uint64_t repair1:14;
+		uint64_t repair2:14;
+		uint64_t reserved_42_63:22;
+#endif
+	} s;
+};
+
+union cvmx_mio_fus_spr_repair_sum {
+	uint64_t u64;
+	struct cvmx_mio_fus_spr_repair_sum_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t too_many:1;
+#else
+		uint64_t too_many:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_mio_fus_tgg {
+	uint64_t u64;
+	struct cvmx_mio_fus_tgg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t val:1;
+		uint64_t dat:63;
+#else
+		uint64_t dat:63;
+		uint64_t val:1;
+#endif
+	} s;
+};
+
+union cvmx_mio_fus_unlock {
+	uint64_t u64;
+	struct cvmx_mio_fus_unlock_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_24_63:40;
+		uint64_t key:24;
+#else
+		uint64_t key:24;
+		uint64_t reserved_24_63:40;
+#endif
+	} s;
+};
+
+union cvmx_mio_fus_wadr {
+	uint64_t u64;
+	struct cvmx_mio_fus_wadr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t addr:10;
+#else
+		uint64_t addr:10;
+		uint64_t reserved_10_63:54;
+#endif
+	} s;
+	struct cvmx_mio_fus_wadr_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t addr:2;
+#else
+		uint64_t addr:2;
+		uint64_t reserved_2_63:62;
+#endif
+	} cn50xx;
+	struct cvmx_mio_fus_wadr_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_3_63:61;
+		uint64_t addr:3;
+#else
+		uint64_t addr:3;
+		uint64_t reserved_3_63:61;
+#endif
+	} cn52xx;
+	struct cvmx_mio_fus_wadr_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t addr:4;
+#else
+		uint64_t addr:4;
+		uint64_t reserved_4_63:60;
+#endif
+	} cn61xx;
+};
+
+union cvmx_mio_gpio_comp {
+	uint64_t u64;
+	struct cvmx_mio_gpio_comp_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t pctl:6;
+		uint64_t nctl:6;
+#else
+		uint64_t nctl:6;
+		uint64_t pctl:6;
+		uint64_t reserved_12_63:52;
+#endif
+	} s;
+};
+
+union cvmx_mio_ndf_dma_cfg {
+	uint64_t u64;
+	struct cvmx_mio_ndf_dma_cfg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t en:1;
+		uint64_t rw:1;
+		uint64_t clr:1;
+		uint64_t reserved_60_60:1;
+		uint64_t swap32:1;
+		uint64_t swap16:1;
+		uint64_t swap8:1;
+		uint64_t endian:1;
+		uint64_t size:20;
+		uint64_t adr:36;
+#else
+		uint64_t adr:36;
+		uint64_t size:20;
+		uint64_t endian:1;
+		uint64_t swap8:1;
+		uint64_t swap16:1;
+		uint64_t swap32:1;
+		uint64_t reserved_60_60:1;
+		uint64_t clr:1;
+		uint64_t rw:1;
+		uint64_t en:1;
+#endif
+	} s;
+};
+
+union cvmx_mio_ndf_dma_int {
+	uint64_t u64;
+	struct cvmx_mio_ndf_dma_int_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t done:1;
+#else
+		uint64_t done:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_mio_ndf_dma_int_en {
+	uint64_t u64;
+	struct cvmx_mio_ndf_dma_int_en_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t done:1;
+#else
+		uint64_t done:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_mio_pll_ctl {
+	uint64_t u64;
+	struct cvmx_mio_pll_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_5_63:59;
+		uint64_t bw_ctl:5;
+#else
+		uint64_t bw_ctl:5;
+		uint64_t reserved_5_63:59;
+#endif
+	} s;
+};
+
+union cvmx_mio_pll_setting {
+	uint64_t u64;
+	struct cvmx_mio_pll_setting_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_17_63:47;
+		uint64_t setting:17;
+#else
+		uint64_t setting:17;
+		uint64_t reserved_17_63:47;
+#endif
+	} s;
+};
+
+union cvmx_mio_ptp_ckout_hi_incr {
+	uint64_t u64;
+	struct cvmx_mio_ptp_ckout_hi_incr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t nanosec:32;
+		uint64_t frnanosec:32;
+#else
+		uint64_t frnanosec:32;
+		uint64_t nanosec:32;
+#endif
+	} s;
+};
+
+union cvmx_mio_ptp_ckout_lo_incr {
+	uint64_t u64;
+	struct cvmx_mio_ptp_ckout_lo_incr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t nanosec:32;
+		uint64_t frnanosec:32;
+#else
+		uint64_t frnanosec:32;
+		uint64_t nanosec:32;
+#endif
+	} s;
+};
+
+union cvmx_mio_ptp_ckout_thresh_hi {
+	uint64_t u64;
+	struct cvmx_mio_ptp_ckout_thresh_hi_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t nanosec:64;
+#else
+		uint64_t nanosec:64;
+#endif
+	} s;
+};
+
+union cvmx_mio_ptp_ckout_thresh_lo {
+	uint64_t u64;
+	struct cvmx_mio_ptp_ckout_thresh_lo_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t frnanosec:32;
+#else
+		uint64_t frnanosec:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_mio_ptp_clock_cfg {
+	uint64_t u64;
+	struct cvmx_mio_ptp_clock_cfg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_42_63:22;
+		uint64_t pps:1;
+		uint64_t ckout:1;
+		uint64_t ext_clk_edge:2;
+		uint64_t ckout_out4:1;
+		uint64_t pps_out:5;
+		uint64_t pps_inv:1;
+		uint64_t pps_en:1;
+		uint64_t ckout_out:4;
+		uint64_t ckout_inv:1;
+		uint64_t ckout_en:1;
+		uint64_t evcnt_in:6;
+		uint64_t evcnt_edge:1;
+		uint64_t evcnt_en:1;
+		uint64_t tstmp_in:6;
+		uint64_t tstmp_edge:1;
+		uint64_t tstmp_en:1;
+		uint64_t ext_clk_in:6;
+		uint64_t ext_clk_en:1;
+		uint64_t ptp_en:1;
+#else
+		uint64_t ptp_en:1;
+		uint64_t ext_clk_en:1;
+		uint64_t ext_clk_in:6;
+		uint64_t tstmp_en:1;
+		uint64_t tstmp_edge:1;
+		uint64_t tstmp_in:6;
+		uint64_t evcnt_en:1;
+		uint64_t evcnt_edge:1;
+		uint64_t evcnt_in:6;
+		uint64_t ckout_en:1;
+		uint64_t ckout_inv:1;
+		uint64_t ckout_out:4;
+		uint64_t pps_en:1;
+		uint64_t pps_inv:1;
+		uint64_t pps_out:5;
+		uint64_t ckout_out4:1;
+		uint64_t ext_clk_edge:2;
+		uint64_t ckout:1;
+		uint64_t pps:1;
+		uint64_t reserved_42_63:22;
+#endif
+	} s;
+	struct cvmx_mio_ptp_clock_cfg_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_24_63:40;
+		uint64_t evcnt_in:6;
+		uint64_t evcnt_edge:1;
+		uint64_t evcnt_en:1;
+		uint64_t tstmp_in:6;
+		uint64_t tstmp_edge:1;
+		uint64_t tstmp_en:1;
+		uint64_t ext_clk_in:6;
+		uint64_t ext_clk_en:1;
+		uint64_t ptp_en:1;
+#else
+		uint64_t ptp_en:1;
+		uint64_t ext_clk_en:1;
+		uint64_t ext_clk_in:6;
+		uint64_t tstmp_en:1;
+		uint64_t tstmp_edge:1;
+		uint64_t tstmp_in:6;
+		uint64_t evcnt_en:1;
+		uint64_t evcnt_edge:1;
+		uint64_t evcnt_in:6;
+		uint64_t reserved_24_63:40;
+#endif
+	} cn63xx;
+	struct cvmx_mio_ptp_clock_cfg_cn66xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_40_63:24;
+		uint64_t ext_clk_edge:2;
+		uint64_t ckout_out4:1;
+		uint64_t pps_out:5;
+		uint64_t pps_inv:1;
+		uint64_t pps_en:1;
+		uint64_t ckout_out:4;
+		uint64_t ckout_inv:1;
+		uint64_t ckout_en:1;
+		uint64_t evcnt_in:6;
+		uint64_t evcnt_edge:1;
+		uint64_t evcnt_en:1;
+		uint64_t tstmp_in:6;
+		uint64_t tstmp_edge:1;
+		uint64_t tstmp_en:1;
+		uint64_t ext_clk_in:6;
+		uint64_t ext_clk_en:1;
+		uint64_t ptp_en:1;
+#else
+		uint64_t ptp_en:1;
+		uint64_t ext_clk_en:1;
+		uint64_t ext_clk_in:6;
+		uint64_t tstmp_en:1;
+		uint64_t tstmp_edge:1;
+		uint64_t tstmp_in:6;
+		uint64_t evcnt_en:1;
+		uint64_t evcnt_edge:1;
+		uint64_t evcnt_in:6;
+		uint64_t ckout_en:1;
+		uint64_t ckout_inv:1;
+		uint64_t ckout_out:4;
+		uint64_t pps_en:1;
+		uint64_t pps_inv:1;
+		uint64_t pps_out:5;
+		uint64_t ckout_out4:1;
+		uint64_t ext_clk_edge:2;
+		uint64_t reserved_40_63:24;
+#endif
+	} cn66xx;
+};
+
+union cvmx_mio_ptp_clock_comp {
+	uint64_t u64;
+	struct cvmx_mio_ptp_clock_comp_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t nanosec:32;
+		uint64_t frnanosec:32;
+#else
+		uint64_t frnanosec:32;
+		uint64_t nanosec:32;
+#endif
+	} s;
+};
+
+union cvmx_mio_ptp_clock_hi {
+	uint64_t u64;
+	struct cvmx_mio_ptp_clock_hi_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t nanosec:64;
+#else
+		uint64_t nanosec:64;
+#endif
+	} s;
+};
+
+union cvmx_mio_ptp_clock_lo {
+	uint64_t u64;
+	struct cvmx_mio_ptp_clock_lo_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t frnanosec:32;
+#else
+		uint64_t frnanosec:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_mio_ptp_evt_cnt {
+	uint64_t u64;
+	struct cvmx_mio_ptp_evt_cnt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t cntr:64;
+#else
+		uint64_t cntr:64;
+#endif
+	} s;
+};
+
+union cvmx_mio_ptp_phy_1pps_in {
+	uint64_t u64;
+	struct cvmx_mio_ptp_phy_1pps_in_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_5_63:59;
+		uint64_t sel:5;
+#else
+		uint64_t sel:5;
+		uint64_t reserved_5_63:59;
+#endif
+	} s;
+};
+
+union cvmx_mio_ptp_pps_hi_incr {
+	uint64_t u64;
+	struct cvmx_mio_ptp_pps_hi_incr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t nanosec:32;
+		uint64_t frnanosec:32;
+#else
+		uint64_t frnanosec:32;
+		uint64_t nanosec:32;
+#endif
+	} s;
+};
+
+union cvmx_mio_ptp_pps_lo_incr {
+	uint64_t u64;
+	struct cvmx_mio_ptp_pps_lo_incr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t nanosec:32;
+		uint64_t frnanosec:32;
+#else
+		uint64_t frnanosec:32;
+		uint64_t nanosec:32;
+#endif
+	} s;
+};
+
+union cvmx_mio_ptp_pps_thresh_hi {
+	uint64_t u64;
+	struct cvmx_mio_ptp_pps_thresh_hi_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t nanosec:64;
+#else
+		uint64_t nanosec:64;
+#endif
+	} s;
+};
+
+union cvmx_mio_ptp_pps_thresh_lo {
+	uint64_t u64;
+	struct cvmx_mio_ptp_pps_thresh_lo_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t frnanosec:32;
+#else
+		uint64_t frnanosec:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_mio_ptp_timestamp {
+	uint64_t u64;
+	struct cvmx_mio_ptp_timestamp_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t nanosec:64;
+#else
+		uint64_t nanosec:64;
+#endif
+	} s;
+};
+
+union cvmx_mio_qlmx_cfg {
+	uint64_t u64;
+	struct cvmx_mio_qlmx_cfg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_15_63:49;
+		uint64_t prtmode:1;
+		uint64_t reserved_12_13:2;
+		uint64_t qlm_spd:4;
+		uint64_t reserved_4_7:4;
+		uint64_t qlm_cfg:4;
+#else
+		uint64_t qlm_cfg:4;
+		uint64_t reserved_4_7:4;
+		uint64_t qlm_spd:4;
+		uint64_t reserved_12_13:2;
+		uint64_t prtmode:1;
+		uint64_t reserved_15_63:49;
+#endif
+	} s;
+	struct cvmx_mio_qlmx_cfg_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_15_63:49;
+		uint64_t prtmode:1;
+		uint64_t reserved_12_13:2;
+		uint64_t qlm_spd:4;
+		uint64_t reserved_2_7:6;
+		uint64_t qlm_cfg:2;
+#else
+		uint64_t qlm_cfg:2;
+		uint64_t reserved_2_7:6;
+		uint64_t qlm_spd:4;
+		uint64_t reserved_12_13:2;
+		uint64_t prtmode:1;
+		uint64_t reserved_15_63:49;
+#endif
+	} cn61xx;
+	struct cvmx_mio_qlmx_cfg_cn66xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t qlm_spd:4;
+		uint64_t reserved_4_7:4;
+		uint64_t qlm_cfg:4;
+#else
+		uint64_t qlm_cfg:4;
+		uint64_t reserved_4_7:4;
+		uint64_t qlm_spd:4;
+		uint64_t reserved_12_63:52;
+#endif
+	} cn66xx;
+	struct cvmx_mio_qlmx_cfg_cn68xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t qlm_spd:4;
+		uint64_t reserved_3_7:5;
+		uint64_t qlm_cfg:3;
+#else
+		uint64_t qlm_cfg:3;
+		uint64_t reserved_3_7:5;
+		uint64_t qlm_spd:4;
+		uint64_t reserved_12_63:52;
+#endif
+	} cn68xx;
+};
+
+union cvmx_mio_rst_boot {
+	uint64_t u64;
+	struct cvmx_mio_rst_boot_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t chipkill:1;
+		uint64_t jtcsrdis:1;
+		uint64_t ejtagdis:1;
+		uint64_t romen:1;
+		uint64_t ckill_ppdis:1;
+		uint64_t jt_tstmode:1;
+		uint64_t reserved_50_57:8;
+		uint64_t lboot_ext:2;
+		uint64_t reserved_44_47:4;
+		uint64_t qlm4_spd:4;
+		uint64_t qlm3_spd:4;
+		uint64_t c_mul:6;
+		uint64_t pnr_mul:6;
+		uint64_t qlm2_spd:4;
+		uint64_t qlm1_spd:4;
+		uint64_t qlm0_spd:4;
+		uint64_t lboot:10;
+		uint64_t rboot:1;
+		uint64_t rboot_pin:1;
+#else
+		uint64_t rboot_pin:1;
+		uint64_t rboot:1;
+		uint64_t lboot:10;
+		uint64_t qlm0_spd:4;
+		uint64_t qlm1_spd:4;
+		uint64_t qlm2_spd:4;
+		uint64_t pnr_mul:6;
+		uint64_t c_mul:6;
+		uint64_t qlm3_spd:4;
+		uint64_t qlm4_spd:4;
+		uint64_t reserved_44_47:4;
+		uint64_t lboot_ext:2;
+		uint64_t reserved_50_57:8;
+		uint64_t jt_tstmode:1;
+		uint64_t ckill_ppdis:1;
+		uint64_t romen:1;
+		uint64_t ejtagdis:1;
+		uint64_t jtcsrdis:1;
+		uint64_t chipkill:1;
+#endif
+	} s;
+	struct cvmx_mio_rst_boot_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t chipkill:1;
+		uint64_t jtcsrdis:1;
+		uint64_t ejtagdis:1;
+		uint64_t romen:1;
+		uint64_t ckill_ppdis:1;
+		uint64_t jt_tstmode:1;
+		uint64_t reserved_50_57:8;
+		uint64_t lboot_ext:2;
+		uint64_t reserved_36_47:12;
+		uint64_t c_mul:6;
+		uint64_t pnr_mul:6;
+		uint64_t qlm2_spd:4;
+		uint64_t qlm1_spd:4;
+		uint64_t qlm0_spd:4;
+		uint64_t lboot:10;
+		uint64_t rboot:1;
+		uint64_t rboot_pin:1;
+#else
+		uint64_t rboot_pin:1;
+		uint64_t rboot:1;
+		uint64_t lboot:10;
+		uint64_t qlm0_spd:4;
+		uint64_t qlm1_spd:4;
+		uint64_t qlm2_spd:4;
+		uint64_t pnr_mul:6;
+		uint64_t c_mul:6;
+		uint64_t reserved_36_47:12;
+		uint64_t lboot_ext:2;
+		uint64_t reserved_50_57:8;
+		uint64_t jt_tstmode:1;
+		uint64_t ckill_ppdis:1;
+		uint64_t romen:1;
+		uint64_t ejtagdis:1;
+		uint64_t jtcsrdis:1;
+		uint64_t chipkill:1;
+#endif
+	} cn61xx;
+	struct cvmx_mio_rst_boot_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_36_63:28;
+		uint64_t c_mul:6;
+		uint64_t pnr_mul:6;
+		uint64_t qlm2_spd:4;
+		uint64_t qlm1_spd:4;
+		uint64_t qlm0_spd:4;
+		uint64_t lboot:10;
+		uint64_t rboot:1;
+		uint64_t rboot_pin:1;
+#else
+		uint64_t rboot_pin:1;
+		uint64_t rboot:1;
+		uint64_t lboot:10;
+		uint64_t qlm0_spd:4;
+		uint64_t qlm1_spd:4;
+		uint64_t qlm2_spd:4;
+		uint64_t pnr_mul:6;
+		uint64_t c_mul:6;
+		uint64_t reserved_36_63:28;
+#endif
+	} cn63xx;
+	struct cvmx_mio_rst_boot_cn66xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t chipkill:1;
+		uint64_t jtcsrdis:1;
+		uint64_t ejtagdis:1;
+		uint64_t romen:1;
+		uint64_t ckill_ppdis:1;
+		uint64_t reserved_50_58:9;
+		uint64_t lboot_ext:2;
+		uint64_t reserved_36_47:12;
+		uint64_t c_mul:6;
+		uint64_t pnr_mul:6;
+		uint64_t qlm2_spd:4;
+		uint64_t qlm1_spd:4;
+		uint64_t qlm0_spd:4;
+		uint64_t lboot:10;
+		uint64_t rboot:1;
+		uint64_t rboot_pin:1;
+#else
+		uint64_t rboot_pin:1;
+		uint64_t rboot:1;
+		uint64_t lboot:10;
+		uint64_t qlm0_spd:4;
+		uint64_t qlm1_spd:4;
+		uint64_t qlm2_spd:4;
+		uint64_t pnr_mul:6;
+		uint64_t c_mul:6;
+		uint64_t reserved_36_47:12;
+		uint64_t lboot_ext:2;
+		uint64_t reserved_50_58:9;
+		uint64_t ckill_ppdis:1;
+		uint64_t romen:1;
+		uint64_t ejtagdis:1;
+		uint64_t jtcsrdis:1;
+		uint64_t chipkill:1;
+#endif
+	} cn66xx;
+	struct cvmx_mio_rst_boot_cn68xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_59_63:5;
+		uint64_t jt_tstmode:1;
+		uint64_t reserved_44_57:14;
+		uint64_t qlm4_spd:4;
+		uint64_t qlm3_spd:4;
+		uint64_t c_mul:6;
+		uint64_t pnr_mul:6;
+		uint64_t qlm2_spd:4;
+		uint64_t qlm1_spd:4;
+		uint64_t qlm0_spd:4;
+		uint64_t lboot:10;
+		uint64_t rboot:1;
+		uint64_t rboot_pin:1;
+#else
+		uint64_t rboot_pin:1;
+		uint64_t rboot:1;
+		uint64_t lboot:10;
+		uint64_t qlm0_spd:4;
+		uint64_t qlm1_spd:4;
+		uint64_t qlm2_spd:4;
+		uint64_t pnr_mul:6;
+		uint64_t c_mul:6;
+		uint64_t qlm3_spd:4;
+		uint64_t qlm4_spd:4;
+		uint64_t reserved_44_57:14;
+		uint64_t jt_tstmode:1;
+		uint64_t reserved_59_63:5;
+#endif
+	} cn68xx;
+	struct cvmx_mio_rst_boot_cn68xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_44_63:20;
+		uint64_t qlm4_spd:4;
+		uint64_t qlm3_spd:4;
+		uint64_t c_mul:6;
+		uint64_t pnr_mul:6;
+		uint64_t qlm2_spd:4;
+		uint64_t qlm1_spd:4;
+		uint64_t qlm0_spd:4;
+		uint64_t lboot:10;
+		uint64_t rboot:1;
+		uint64_t rboot_pin:1;
+#else
+		uint64_t rboot_pin:1;
+		uint64_t rboot:1;
+		uint64_t lboot:10;
+		uint64_t qlm0_spd:4;
+		uint64_t qlm1_spd:4;
+		uint64_t qlm2_spd:4;
+		uint64_t pnr_mul:6;
+		uint64_t c_mul:6;
+		uint64_t qlm3_spd:4;
+		uint64_t qlm4_spd:4;
+		uint64_t reserved_44_63:20;
+#endif
+	} cn68xxp1;
+};
+
+union cvmx_mio_rst_cfg {
+	uint64_t u64;
+	struct cvmx_mio_rst_cfg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_3_63:61;
+		uint64_t cntl_clr_bist:1;
+		uint64_t warm_clr_bist:1;
+		uint64_t soft_clr_bist:1;
+#else
+		uint64_t soft_clr_bist:1;
+		uint64_t warm_clr_bist:1;
+		uint64_t cntl_clr_bist:1;
+		uint64_t reserved_3_63:61;
+#endif
+	} s;
+	struct cvmx_mio_rst_cfg_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t bist_delay:58;
+		uint64_t reserved_3_5:3;
+		uint64_t cntl_clr_bist:1;
+		uint64_t warm_clr_bist:1;
+		uint64_t soft_clr_bist:1;
+#else
+		uint64_t soft_clr_bist:1;
+		uint64_t warm_clr_bist:1;
+		uint64_t cntl_clr_bist:1;
+		uint64_t reserved_3_5:3;
+		uint64_t bist_delay:58;
+#endif
+	} cn61xx;
+	struct cvmx_mio_rst_cfg_cn63xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t bist_delay:58;
+		uint64_t reserved_2_5:4;
+		uint64_t warm_clr_bist:1;
+		uint64_t soft_clr_bist:1;
+#else
+		uint64_t soft_clr_bist:1;
+		uint64_t warm_clr_bist:1;
+		uint64_t reserved_2_5:4;
+		uint64_t bist_delay:58;
+#endif
+	} cn63xxp1;
+	struct cvmx_mio_rst_cfg_cn68xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t bist_delay:56;
+		uint64_t reserved_3_7:5;
+		uint64_t cntl_clr_bist:1;
+		uint64_t warm_clr_bist:1;
+		uint64_t soft_clr_bist:1;
+#else
+		uint64_t soft_clr_bist:1;
+		uint64_t warm_clr_bist:1;
+		uint64_t cntl_clr_bist:1;
+		uint64_t reserved_3_7:5;
+		uint64_t bist_delay:56;
+#endif
+	} cn68xx;
+};
+
+union cvmx_mio_rst_ckill {
+	uint64_t u64;
+	struct cvmx_mio_rst_ckill_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_47_63:17;
+		uint64_t timer:47;
+#else
+		uint64_t timer:47;
+		uint64_t reserved_47_63:17;
+#endif
+	} s;
+};
+
+union cvmx_mio_rst_cntlx {
+	uint64_t u64;
+	struct cvmx_mio_rst_cntlx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_13_63:51;
+		uint64_t in_rev_ln:1;
+		uint64_t rev_lanes:1;
+		uint64_t gen1_only:1;
+		uint64_t prst_link:1;
+		uint64_t rst_done:1;
+		uint64_t rst_link:1;
+		uint64_t host_mode:1;
+		uint64_t prtmode:2;
+		uint64_t rst_drv:1;
+		uint64_t rst_rcv:1;
+		uint64_t rst_chip:1;
+		uint64_t rst_val:1;
+#else
+		uint64_t rst_val:1;
+		uint64_t rst_chip:1;
+		uint64_t rst_rcv:1;
+		uint64_t rst_drv:1;
+		uint64_t prtmode:2;
+		uint64_t host_mode:1;
+		uint64_t rst_link:1;
+		uint64_t rst_done:1;
+		uint64_t prst_link:1;
+		uint64_t gen1_only:1;
+		uint64_t rev_lanes:1;
+		uint64_t in_rev_ln:1;
+		uint64_t reserved_13_63:51;
+#endif
+	} s;
+	struct cvmx_mio_rst_cntlx_cn66xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t prst_link:1;
+		uint64_t rst_done:1;
+		uint64_t rst_link:1;
+		uint64_t host_mode:1;
+		uint64_t prtmode:2;
+		uint64_t rst_drv:1;
+		uint64_t rst_rcv:1;
+		uint64_t rst_chip:1;
+		uint64_t rst_val:1;
+#else
+		uint64_t rst_val:1;
+		uint64_t rst_chip:1;
+		uint64_t rst_rcv:1;
+		uint64_t rst_drv:1;
+		uint64_t prtmode:2;
+		uint64_t host_mode:1;
+		uint64_t rst_link:1;
+		uint64_t rst_done:1;
+		uint64_t prst_link:1;
+		uint64_t reserved_10_63:54;
+#endif
+	} cn66xx;
+};
+
+union cvmx_mio_rst_ctlx {
+	uint64_t u64;
+	struct cvmx_mio_rst_ctlx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_13_63:51;
+		uint64_t in_rev_ln:1;
+		uint64_t rev_lanes:1;
+		uint64_t gen1_only:1;
+		uint64_t prst_link:1;
+		uint64_t rst_done:1;
+		uint64_t rst_link:1;
+		uint64_t host_mode:1;
+		uint64_t prtmode:2;
+		uint64_t rst_drv:1;
+		uint64_t rst_rcv:1;
+		uint64_t rst_chip:1;
+		uint64_t rst_val:1;
+#else
+		uint64_t rst_val:1;
+		uint64_t rst_chip:1;
+		uint64_t rst_rcv:1;
+		uint64_t rst_drv:1;
+		uint64_t prtmode:2;
+		uint64_t host_mode:1;
+		uint64_t rst_link:1;
+		uint64_t rst_done:1;
+		uint64_t prst_link:1;
+		uint64_t gen1_only:1;
+		uint64_t rev_lanes:1;
+		uint64_t in_rev_ln:1;
+		uint64_t reserved_13_63:51;
+#endif
+	} s;
+	struct cvmx_mio_rst_ctlx_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t prst_link:1;
+		uint64_t rst_done:1;
+		uint64_t rst_link:1;
+		uint64_t host_mode:1;
+		uint64_t prtmode:2;
+		uint64_t rst_drv:1;
+		uint64_t rst_rcv:1;
+		uint64_t rst_chip:1;
+		uint64_t rst_val:1;
+#else
+		uint64_t rst_val:1;
+		uint64_t rst_chip:1;
+		uint64_t rst_rcv:1;
+		uint64_t rst_drv:1;
+		uint64_t prtmode:2;
+		uint64_t host_mode:1;
+		uint64_t rst_link:1;
+		uint64_t rst_done:1;
+		uint64_t prst_link:1;
+		uint64_t reserved_10_63:54;
+#endif
+	} cn63xx;
+	struct cvmx_mio_rst_ctlx_cn63xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_9_63:55;
+		uint64_t rst_done:1;
+		uint64_t rst_link:1;
+		uint64_t host_mode:1;
+		uint64_t prtmode:2;
+		uint64_t rst_drv:1;
+		uint64_t rst_rcv:1;
+		uint64_t rst_chip:1;
+		uint64_t rst_val:1;
+#else
+		uint64_t rst_val:1;
+		uint64_t rst_chip:1;
+		uint64_t rst_rcv:1;
+		uint64_t rst_drv:1;
+		uint64_t prtmode:2;
+		uint64_t host_mode:1;
+		uint64_t rst_link:1;
+		uint64_t rst_done:1;
+		uint64_t reserved_9_63:55;
+#endif
+	} cn63xxp1;
+};
+
+union cvmx_mio_rst_delay {
+	uint64_t u64;
+	struct cvmx_mio_rst_delay_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t warm_rst_dly:16;
+		uint64_t soft_rst_dly:16;
+#else
+		uint64_t soft_rst_dly:16;
+		uint64_t warm_rst_dly:16;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_mio_rst_int {
+	uint64_t u64;
+	struct cvmx_mio_rst_int_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t perst1:1;
+		uint64_t perst0:1;
+		uint64_t reserved_4_7:4;
+		uint64_t rst_link3:1;
+		uint64_t rst_link2:1;
+		uint64_t rst_link1:1;
+		uint64_t rst_link0:1;
+#else
+		uint64_t rst_link0:1;
+		uint64_t rst_link1:1;
+		uint64_t rst_link2:1;
+		uint64_t rst_link3:1;
+		uint64_t reserved_4_7:4;
+		uint64_t perst0:1;
+		uint64_t perst1:1;
+		uint64_t reserved_10_63:54;
+#endif
+	} s;
+	struct cvmx_mio_rst_int_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t perst1:1;
+		uint64_t perst0:1;
+		uint64_t reserved_2_7:6;
+		uint64_t rst_link1:1;
+		uint64_t rst_link0:1;
+#else
+		uint64_t rst_link0:1;
+		uint64_t rst_link1:1;
+		uint64_t reserved_2_7:6;
+		uint64_t perst0:1;
+		uint64_t perst1:1;
+		uint64_t reserved_10_63:54;
+#endif
+	} cn61xx;
+};
+
+union cvmx_mio_rst_int_en {
+	uint64_t u64;
+	struct cvmx_mio_rst_int_en_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t perst1:1;
+		uint64_t perst0:1;
+		uint64_t reserved_4_7:4;
+		uint64_t rst_link3:1;
+		uint64_t rst_link2:1;
+		uint64_t rst_link1:1;
+		uint64_t rst_link0:1;
+#else
+		uint64_t rst_link0:1;
+		uint64_t rst_link1:1;
+		uint64_t rst_link2:1;
+		uint64_t rst_link3:1;
+		uint64_t reserved_4_7:4;
+		uint64_t perst0:1;
+		uint64_t perst1:1;
+		uint64_t reserved_10_63:54;
+#endif
+	} s;
+	struct cvmx_mio_rst_int_en_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t perst1:1;
+		uint64_t perst0:1;
+		uint64_t reserved_2_7:6;
+		uint64_t rst_link1:1;
+		uint64_t rst_link0:1;
+#else
+		uint64_t rst_link0:1;
+		uint64_t rst_link1:1;
+		uint64_t reserved_2_7:6;
+		uint64_t perst0:1;
+		uint64_t perst1:1;
+		uint64_t reserved_10_63:54;
+#endif
+	} cn61xx;
+};
+
+union cvmx_mio_twsx_int {
+	uint64_t u64;
+	struct cvmx_mio_twsx_int_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t scl:1;
+		uint64_t sda:1;
+		uint64_t scl_ovr:1;
+		uint64_t sda_ovr:1;
+		uint64_t reserved_7_7:1;
+		uint64_t core_en:1;
+		uint64_t ts_en:1;
+		uint64_t st_en:1;
+		uint64_t reserved_3_3:1;
+		uint64_t core_int:1;
+		uint64_t ts_int:1;
+		uint64_t st_int:1;
+#else
+		uint64_t st_int:1;
+		uint64_t ts_int:1;
+		uint64_t core_int:1;
+		uint64_t reserved_3_3:1;
+		uint64_t st_en:1;
+		uint64_t ts_en:1;
+		uint64_t core_en:1;
+		uint64_t reserved_7_7:1;
+		uint64_t sda_ovr:1;
+		uint64_t scl_ovr:1;
+		uint64_t sda:1;
+		uint64_t scl:1;
+		uint64_t reserved_12_63:52;
+#endif
+	} s;
+	struct cvmx_mio_twsx_int_cn38xxp2 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t core_en:1;
+		uint64_t ts_en:1;
+		uint64_t st_en:1;
+		uint64_t reserved_3_3:1;
+		uint64_t core_int:1;
+		uint64_t ts_int:1;
+		uint64_t st_int:1;
+#else
+		uint64_t st_int:1;
+		uint64_t ts_int:1;
+		uint64_t core_int:1;
+		uint64_t reserved_3_3:1;
+		uint64_t st_en:1;
+		uint64_t ts_en:1;
+		uint64_t core_en:1;
+		uint64_t reserved_7_63:57;
+#endif
+	} cn38xxp2;
+};
+
+union cvmx_mio_twsx_sw_twsi {
+	uint64_t u64;
+	struct cvmx_mio_twsx_sw_twsi_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t v:1;
+		uint64_t slonly:1;
+		uint64_t eia:1;
+		uint64_t op:4;
+		uint64_t r:1;
+		uint64_t sovr:1;
+		uint64_t size:3;
+		uint64_t scr:2;
+		uint64_t a:10;
+		uint64_t ia:5;
+		uint64_t eop_ia:3;
+		uint64_t d:32;
+#else
+		uint64_t d:32;
+		uint64_t eop_ia:3;
+		uint64_t ia:5;
+		uint64_t a:10;
+		uint64_t scr:2;
+		uint64_t size:3;
+		uint64_t sovr:1;
+		uint64_t r:1;
+		uint64_t op:4;
+		uint64_t eia:1;
+		uint64_t slonly:1;
+		uint64_t v:1;
+#endif
+	} s;
+};
+
+union cvmx_mio_twsx_sw_twsi_ext {
+	uint64_t u64;
+	struct cvmx_mio_twsx_sw_twsi_ext_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_40_63:24;
+		uint64_t ia:8;
+		uint64_t d:32;
+#else
+		uint64_t d:32;
+		uint64_t ia:8;
+		uint64_t reserved_40_63:24;
+#endif
+	} s;
+};
+
+union cvmx_mio_twsx_twsi_sw {
+	uint64_t u64;
+	struct cvmx_mio_twsx_twsi_sw_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t v:2;
+		uint64_t reserved_32_61:30;
+		uint64_t d:32;
+#else
+		uint64_t d:32;
+		uint64_t reserved_32_61:30;
+		uint64_t v:2;
+#endif
+	} s;
+};
+
+union cvmx_mio_uartx_dlh {
+	uint64_t u64;
+	struct cvmx_mio_uartx_dlh_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t dlh:8;
+#else
+		uint64_t dlh:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_mio_uartx_dll {
+	uint64_t u64;
+	struct cvmx_mio_uartx_dll_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t dll:8;
+#else
+		uint64_t dll:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_mio_uartx_far {
+	uint64_t u64;
+	struct cvmx_mio_uartx_far_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t far:1;
+#else
+		uint64_t far:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_mio_uartx_fcr {
+	uint64_t u64;
+	struct cvmx_mio_uartx_fcr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t rxtrig:2;
+		uint64_t txtrig:2;
+		uint64_t reserved_3_3:1;
+		uint64_t txfr:1;
+		uint64_t rxfr:1;
+		uint64_t en:1;
+#else
+		uint64_t en:1;
+		uint64_t rxfr:1;
+		uint64_t txfr:1;
+		uint64_t reserved_3_3:1;
+		uint64_t txtrig:2;
+		uint64_t rxtrig:2;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_mio_uartx_htx {
+	uint64_t u64;
+	struct cvmx_mio_uartx_htx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t htx:1;
+#else
+		uint64_t htx:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_mio_uartx_ier {
+	uint64_t u64;
+	struct cvmx_mio_uartx_ier_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t ptime:1;
+		uint64_t reserved_4_6:3;
+		uint64_t edssi:1;
+		uint64_t elsi:1;
+		uint64_t etbei:1;
+		uint64_t erbfi:1;
+#else
+		uint64_t erbfi:1;
+		uint64_t etbei:1;
+		uint64_t elsi:1;
+		uint64_t edssi:1;
+		uint64_t reserved_4_6:3;
+		uint64_t ptime:1;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_mio_uartx_iir {
+	uint64_t u64;
+	struct cvmx_mio_uartx_iir_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t fen:2;
+		uint64_t reserved_4_5:2;
+		uint64_t iid:4;
+#else
+		uint64_t iid:4;
+		uint64_t reserved_4_5:2;
+		uint64_t fen:2;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_mio_uartx_lcr {
+	uint64_t u64;
+	struct cvmx_mio_uartx_lcr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t dlab:1;
+		uint64_t brk:1;
+		uint64_t reserved_5_5:1;
+		uint64_t eps:1;
+		uint64_t pen:1;
+		uint64_t stop:1;
+		uint64_t cls:2;
+#else
+		uint64_t cls:2;
+		uint64_t stop:1;
+		uint64_t pen:1;
+		uint64_t eps:1;
+		uint64_t reserved_5_5:1;
+		uint64_t brk:1;
+		uint64_t dlab:1;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_mio_uartx_lsr {
+	uint64_t u64;
+	struct cvmx_mio_uartx_lsr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t ferr:1;
+		uint64_t temt:1;
+		uint64_t thre:1;
+		uint64_t bi:1;
+		uint64_t fe:1;
+		uint64_t pe:1;
+		uint64_t oe:1;
+		uint64_t dr:1;
+#else
+		uint64_t dr:1;
+		uint64_t oe:1;
+		uint64_t pe:1;
+		uint64_t fe:1;
+		uint64_t bi:1;
+		uint64_t thre:1;
+		uint64_t temt:1;
+		uint64_t ferr:1;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_mio_uartx_mcr {
+	uint64_t u64;
+	struct cvmx_mio_uartx_mcr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t afce:1;
+		uint64_t loop:1;
+		uint64_t out2:1;
+		uint64_t out1:1;
+		uint64_t rts:1;
+		uint64_t dtr:1;
+#else
+		uint64_t dtr:1;
+		uint64_t rts:1;
+		uint64_t out1:1;
+		uint64_t out2:1;
+		uint64_t loop:1;
+		uint64_t afce:1;
+		uint64_t reserved_6_63:58;
+#endif
+	} s;
+};
+
+union cvmx_mio_uartx_msr {
+	uint64_t u64;
+	struct cvmx_mio_uartx_msr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t dcd:1;
+		uint64_t ri:1;
+		uint64_t dsr:1;
+		uint64_t cts:1;
+		uint64_t ddcd:1;
+		uint64_t teri:1;
+		uint64_t ddsr:1;
+		uint64_t dcts:1;
+#else
+		uint64_t dcts:1;
+		uint64_t ddsr:1;
+		uint64_t teri:1;
+		uint64_t ddcd:1;
+		uint64_t cts:1;
+		uint64_t dsr:1;
+		uint64_t ri:1;
+		uint64_t dcd:1;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_mio_uartx_rbr {
+	uint64_t u64;
+	struct cvmx_mio_uartx_rbr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t rbr:8;
+#else
+		uint64_t rbr:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_mio_uartx_rfl {
+	uint64_t u64;
+	struct cvmx_mio_uartx_rfl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t rfl:7;
+#else
+		uint64_t rfl:7;
+		uint64_t reserved_7_63:57;
+#endif
+	} s;
+};
+
+union cvmx_mio_uartx_rfw {
+	uint64_t u64;
+	struct cvmx_mio_uartx_rfw_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t rffe:1;
+		uint64_t rfpe:1;
+		uint64_t rfwd:8;
+#else
+		uint64_t rfwd:8;
+		uint64_t rfpe:1;
+		uint64_t rffe:1;
+		uint64_t reserved_10_63:54;
+#endif
+	} s;
+};
+
+union cvmx_mio_uartx_sbcr {
+	uint64_t u64;
+	struct cvmx_mio_uartx_sbcr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t sbcr:1;
+#else
+		uint64_t sbcr:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_mio_uartx_scr {
+	uint64_t u64;
+	struct cvmx_mio_uartx_scr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t scr:8;
+#else
+		uint64_t scr:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_mio_uartx_sfe {
+	uint64_t u64;
+	struct cvmx_mio_uartx_sfe_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t sfe:1;
+#else
+		uint64_t sfe:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_mio_uartx_srr {
+	uint64_t u64;
+	struct cvmx_mio_uartx_srr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_3_63:61;
+		uint64_t stfr:1;
+		uint64_t srfr:1;
+		uint64_t usr:1;
+#else
+		uint64_t usr:1;
+		uint64_t srfr:1;
+		uint64_t stfr:1;
+		uint64_t reserved_3_63:61;
+#endif
+	} s;
+};
+
+union cvmx_mio_uartx_srt {
+	uint64_t u64;
+	struct cvmx_mio_uartx_srt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t srt:2;
+#else
+		uint64_t srt:2;
+		uint64_t reserved_2_63:62;
+#endif
+	} s;
+};
+
+union cvmx_mio_uartx_srts {
+	uint64_t u64;
+	struct cvmx_mio_uartx_srts_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t srts:1;
+#else
+		uint64_t srts:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_mio_uartx_stt {
+	uint64_t u64;
+	struct cvmx_mio_uartx_stt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t stt:2;
+#else
+		uint64_t stt:2;
+		uint64_t reserved_2_63:62;
+#endif
+	} s;
+};
+
+union cvmx_mio_uartx_tfl {
+	uint64_t u64;
+	struct cvmx_mio_uartx_tfl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t tfl:7;
+#else
+		uint64_t tfl:7;
+		uint64_t reserved_7_63:57;
+#endif
+	} s;
+};
+
+union cvmx_mio_uartx_tfr {
+	uint64_t u64;
+	struct cvmx_mio_uartx_tfr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t tfr:8;
+#else
+		uint64_t tfr:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_mio_uartx_thr {
+	uint64_t u64;
+	struct cvmx_mio_uartx_thr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t thr:8;
+#else
+		uint64_t thr:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_mio_uartx_usr {
+	uint64_t u64;
+	struct cvmx_mio_uartx_usr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_5_63:59;
+		uint64_t rff:1;
+		uint64_t rfne:1;
+		uint64_t tfe:1;
+		uint64_t tfnf:1;
+		uint64_t busy:1;
+#else
+		uint64_t busy:1;
+		uint64_t tfnf:1;
+		uint64_t tfe:1;
+		uint64_t rfne:1;
+		uint64_t rff:1;
+		uint64_t reserved_5_63:59;
+#endif
+	} s;
+};
+
+union cvmx_mio_uart2_dlh {
+	uint64_t u64;
+	struct cvmx_mio_uart2_dlh_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t dlh:8;
+#else
+		uint64_t dlh:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_mio_uart2_dll {
+	uint64_t u64;
+	struct cvmx_mio_uart2_dll_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t dll:8;
+#else
+		uint64_t dll:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_mio_uart2_far {
+	uint64_t u64;
+	struct cvmx_mio_uart2_far_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t far:1;
+#else
+		uint64_t far:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_mio_uart2_fcr {
+	uint64_t u64;
+	struct cvmx_mio_uart2_fcr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t rxtrig:2;
+		uint64_t txtrig:2;
+		uint64_t reserved_3_3:1;
+		uint64_t txfr:1;
+		uint64_t rxfr:1;
+		uint64_t en:1;
+#else
+		uint64_t en:1;
+		uint64_t rxfr:1;
+		uint64_t txfr:1;
+		uint64_t reserved_3_3:1;
+		uint64_t txtrig:2;
+		uint64_t rxtrig:2;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_mio_uart2_htx {
+	uint64_t u64;
+	struct cvmx_mio_uart2_htx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t htx:1;
+#else
+		uint64_t htx:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_mio_uart2_ier {
+	uint64_t u64;
+	struct cvmx_mio_uart2_ier_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t ptime:1;
+		uint64_t reserved_4_6:3;
+		uint64_t edssi:1;
+		uint64_t elsi:1;
+		uint64_t etbei:1;
+		uint64_t erbfi:1;
+#else
+		uint64_t erbfi:1;
+		uint64_t etbei:1;
+		uint64_t elsi:1;
+		uint64_t edssi:1;
+		uint64_t reserved_4_6:3;
+		uint64_t ptime:1;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_mio_uart2_iir {
+	uint64_t u64;
+	struct cvmx_mio_uart2_iir_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t fen:2;
+		uint64_t reserved_4_5:2;
+		uint64_t iid:4;
+#else
+		uint64_t iid:4;
+		uint64_t reserved_4_5:2;
+		uint64_t fen:2;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_mio_uart2_lcr {
+	uint64_t u64;
+	struct cvmx_mio_uart2_lcr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t dlab:1;
+		uint64_t brk:1;
+		uint64_t reserved_5_5:1;
+		uint64_t eps:1;
+		uint64_t pen:1;
+		uint64_t stop:1;
+		uint64_t cls:2;
+#else
+		uint64_t cls:2;
+		uint64_t stop:1;
+		uint64_t pen:1;
+		uint64_t eps:1;
+		uint64_t reserved_5_5:1;
+		uint64_t brk:1;
+		uint64_t dlab:1;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_mio_uart2_lsr {
+	uint64_t u64;
+	struct cvmx_mio_uart2_lsr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t ferr:1;
+		uint64_t temt:1;
+		uint64_t thre:1;
+		uint64_t bi:1;
+		uint64_t fe:1;
+		uint64_t pe:1;
+		uint64_t oe:1;
+		uint64_t dr:1;
+#else
+		uint64_t dr:1;
+		uint64_t oe:1;
+		uint64_t pe:1;
+		uint64_t fe:1;
+		uint64_t bi:1;
+		uint64_t thre:1;
+		uint64_t temt:1;
+		uint64_t ferr:1;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_mio_uart2_mcr {
+	uint64_t u64;
+	struct cvmx_mio_uart2_mcr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t afce:1;
+		uint64_t loop:1;
+		uint64_t out2:1;
+		uint64_t out1:1;
+		uint64_t rts:1;
+		uint64_t dtr:1;
+#else
+		uint64_t dtr:1;
+		uint64_t rts:1;
+		uint64_t out1:1;
+		uint64_t out2:1;
+		uint64_t loop:1;
+		uint64_t afce:1;
+		uint64_t reserved_6_63:58;
+#endif
+	} s;
+};
+
+union cvmx_mio_uart2_msr {
+	uint64_t u64;
+	struct cvmx_mio_uart2_msr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t dcd:1;
+		uint64_t ri:1;
+		uint64_t dsr:1;
+		uint64_t cts:1;
+		uint64_t ddcd:1;
+		uint64_t teri:1;
+		uint64_t ddsr:1;
+		uint64_t dcts:1;
+#else
+		uint64_t dcts:1;
+		uint64_t ddsr:1;
+		uint64_t teri:1;
+		uint64_t ddcd:1;
+		uint64_t cts:1;
+		uint64_t dsr:1;
+		uint64_t ri:1;
+		uint64_t dcd:1;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_mio_uart2_rbr {
+	uint64_t u64;
+	struct cvmx_mio_uart2_rbr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t rbr:8;
+#else
+		uint64_t rbr:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_mio_uart2_rfl {
+	uint64_t u64;
+	struct cvmx_mio_uart2_rfl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t rfl:7;
+#else
+		uint64_t rfl:7;
+		uint64_t reserved_7_63:57;
+#endif
+	} s;
+};
+
+union cvmx_mio_uart2_rfw {
+	uint64_t u64;
+	struct cvmx_mio_uart2_rfw_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t rffe:1;
+		uint64_t rfpe:1;
+		uint64_t rfwd:8;
+#else
+		uint64_t rfwd:8;
+		uint64_t rfpe:1;
+		uint64_t rffe:1;
+		uint64_t reserved_10_63:54;
+#endif
+	} s;
+};
+
+union cvmx_mio_uart2_sbcr {
+	uint64_t u64;
+	struct cvmx_mio_uart2_sbcr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t sbcr:1;
+#else
+		uint64_t sbcr:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_mio_uart2_scr {
+	uint64_t u64;
+	struct cvmx_mio_uart2_scr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t scr:8;
+#else
+		uint64_t scr:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_mio_uart2_sfe {
+	uint64_t u64;
+	struct cvmx_mio_uart2_sfe_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t sfe:1;
+#else
+		uint64_t sfe:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_mio_uart2_srr {
+	uint64_t u64;
+	struct cvmx_mio_uart2_srr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_3_63:61;
+		uint64_t stfr:1;
+		uint64_t srfr:1;
+		uint64_t usr:1;
+#else
+		uint64_t usr:1;
+		uint64_t srfr:1;
+		uint64_t stfr:1;
+		uint64_t reserved_3_63:61;
+#endif
+	} s;
+};
+
+union cvmx_mio_uart2_srt {
+	uint64_t u64;
+	struct cvmx_mio_uart2_srt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t srt:2;
+#else
+		uint64_t srt:2;
+		uint64_t reserved_2_63:62;
+#endif
+	} s;
+};
+
+union cvmx_mio_uart2_srts {
+	uint64_t u64;
+	struct cvmx_mio_uart2_srts_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t srts:1;
+#else
+		uint64_t srts:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_mio_uart2_stt {
+	uint64_t u64;
+	struct cvmx_mio_uart2_stt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t stt:2;
+#else
+		uint64_t stt:2;
+		uint64_t reserved_2_63:62;
+#endif
+	} s;
+};
+
+union cvmx_mio_uart2_tfl {
+	uint64_t u64;
+	struct cvmx_mio_uart2_tfl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t tfl:7;
+#else
+		uint64_t tfl:7;
+		uint64_t reserved_7_63:57;
+#endif
+	} s;
+};
+
+union cvmx_mio_uart2_tfr {
+	uint64_t u64;
+	struct cvmx_mio_uart2_tfr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t tfr:8;
+#else
+		uint64_t tfr:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_mio_uart2_thr {
+	uint64_t u64;
+	struct cvmx_mio_uart2_thr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t thr:8;
+#else
+		uint64_t thr:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_mio_uart2_usr {
+	uint64_t u64;
+	struct cvmx_mio_uart2_usr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_5_63:59;
+		uint64_t rff:1;
+		uint64_t rfne:1;
+		uint64_t tfe:1;
+		uint64_t tfnf:1;
+		uint64_t busy:1;
+#else
+		uint64_t busy:1;
+		uint64_t tfnf:1;
+		uint64_t tfe:1;
+		uint64_t rfne:1;
+		uint64_t rff:1;
+		uint64_t reserved_5_63:59;
+#endif
+	} s;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-mixx-defs.h b/arch/mips/include/asm/octeon/cvmx-mixx-defs.h
new file mode 100644
index 000000000..cd60d43e8
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-mixx-defs.h
@@ -0,0 +1,430 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2012 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_MIXX_DEFS_H__
+#define __CVMX_MIXX_DEFS_H__
+
+#define CVMX_MIXX_BIST(offset) (CVMX_ADD_IO_SEG(0x0001070000100078ull) + ((offset) & 1) * 2048)
+#define CVMX_MIXX_CTL(offset) (CVMX_ADD_IO_SEG(0x0001070000100020ull) + ((offset) & 1) * 2048)
+#define CVMX_MIXX_INTENA(offset) (CVMX_ADD_IO_SEG(0x0001070000100050ull) + ((offset) & 1) * 2048)
+#define CVMX_MIXX_IRCNT(offset) (CVMX_ADD_IO_SEG(0x0001070000100030ull) + ((offset) & 1) * 2048)
+#define CVMX_MIXX_IRHWM(offset) (CVMX_ADD_IO_SEG(0x0001070000100028ull) + ((offset) & 1) * 2048)
+#define CVMX_MIXX_IRING1(offset) (CVMX_ADD_IO_SEG(0x0001070000100010ull) + ((offset) & 1) * 2048)
+#define CVMX_MIXX_IRING2(offset) (CVMX_ADD_IO_SEG(0x0001070000100018ull) + ((offset) & 1) * 2048)
+#define CVMX_MIXX_ISR(offset) (CVMX_ADD_IO_SEG(0x0001070000100048ull) + ((offset) & 1) * 2048)
+#define CVMX_MIXX_ORCNT(offset) (CVMX_ADD_IO_SEG(0x0001070000100040ull) + ((offset) & 1) * 2048)
+#define CVMX_MIXX_ORHWM(offset) (CVMX_ADD_IO_SEG(0x0001070000100038ull) + ((offset) & 1) * 2048)
+#define CVMX_MIXX_ORING1(offset) (CVMX_ADD_IO_SEG(0x0001070000100000ull) + ((offset) & 1) * 2048)
+#define CVMX_MIXX_ORING2(offset) (CVMX_ADD_IO_SEG(0x0001070000100008ull) + ((offset) & 1) * 2048)
+#define CVMX_MIXX_REMCNT(offset) (CVMX_ADD_IO_SEG(0x0001070000100058ull) + ((offset) & 1) * 2048)
+#define CVMX_MIXX_TSCTL(offset) (CVMX_ADD_IO_SEG(0x0001070000100068ull) + ((offset) & 1) * 2048)
+#define CVMX_MIXX_TSTAMP(offset) (CVMX_ADD_IO_SEG(0x0001070000100060ull) + ((offset) & 1) * 2048)
+
+union cvmx_mixx_bist {
+	uint64_t u64;
+	struct cvmx_mixx_bist_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t opfdat:1;
+		uint64_t mrgdat:1;
+		uint64_t mrqdat:1;
+		uint64_t ipfdat:1;
+		uint64_t irfdat:1;
+		uint64_t orfdat:1;
+#else
+		uint64_t orfdat:1;
+		uint64_t irfdat:1;
+		uint64_t ipfdat:1;
+		uint64_t mrqdat:1;
+		uint64_t mrgdat:1;
+		uint64_t opfdat:1;
+		uint64_t reserved_6_63:58;
+#endif
+	} s;
+	struct cvmx_mixx_bist_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t mrqdat:1;
+		uint64_t ipfdat:1;
+		uint64_t irfdat:1;
+		uint64_t orfdat:1;
+#else
+		uint64_t orfdat:1;
+		uint64_t irfdat:1;
+		uint64_t ipfdat:1;
+		uint64_t mrqdat:1;
+		uint64_t reserved_4_63:60;
+#endif
+	} cn52xx;
+};
+
+union cvmx_mixx_ctl {
+	uint64_t u64;
+	struct cvmx_mixx_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t ts_thresh:4;
+		uint64_t crc_strip:1;
+		uint64_t busy:1;
+		uint64_t en:1;
+		uint64_t reset:1;
+		uint64_t lendian:1;
+		uint64_t nbtarb:1;
+		uint64_t mrq_hwm:2;
+#else
+		uint64_t mrq_hwm:2;
+		uint64_t nbtarb:1;
+		uint64_t lendian:1;
+		uint64_t reset:1;
+		uint64_t en:1;
+		uint64_t busy:1;
+		uint64_t crc_strip:1;
+		uint64_t ts_thresh:4;
+		uint64_t reserved_12_63:52;
+#endif
+	} s;
+	struct cvmx_mixx_ctl_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t crc_strip:1;
+		uint64_t busy:1;
+		uint64_t en:1;
+		uint64_t reset:1;
+		uint64_t lendian:1;
+		uint64_t nbtarb:1;
+		uint64_t mrq_hwm:2;
+#else
+		uint64_t mrq_hwm:2;
+		uint64_t nbtarb:1;
+		uint64_t lendian:1;
+		uint64_t reset:1;
+		uint64_t en:1;
+		uint64_t busy:1;
+		uint64_t crc_strip:1;
+		uint64_t reserved_8_63:56;
+#endif
+	} cn52xx;
+};
+
+union cvmx_mixx_intena {
+	uint64_t u64;
+	struct cvmx_mixx_intena_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t tsena:1;
+		uint64_t orunena:1;
+		uint64_t irunena:1;
+		uint64_t data_drpena:1;
+		uint64_t ithena:1;
+		uint64_t othena:1;
+		uint64_t ivfena:1;
+		uint64_t ovfena:1;
+#else
+		uint64_t ovfena:1;
+		uint64_t ivfena:1;
+		uint64_t othena:1;
+		uint64_t ithena:1;
+		uint64_t data_drpena:1;
+		uint64_t irunena:1;
+		uint64_t orunena:1;
+		uint64_t tsena:1;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+	struct cvmx_mixx_intena_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t orunena:1;
+		uint64_t irunena:1;
+		uint64_t data_drpena:1;
+		uint64_t ithena:1;
+		uint64_t othena:1;
+		uint64_t ivfena:1;
+		uint64_t ovfena:1;
+#else
+		uint64_t ovfena:1;
+		uint64_t ivfena:1;
+		uint64_t othena:1;
+		uint64_t ithena:1;
+		uint64_t data_drpena:1;
+		uint64_t irunena:1;
+		uint64_t orunena:1;
+		uint64_t reserved_7_63:57;
+#endif
+	} cn52xx;
+};
+
+union cvmx_mixx_ircnt {
+	uint64_t u64;
+	struct cvmx_mixx_ircnt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t ircnt:20;
+#else
+		uint64_t ircnt:20;
+		uint64_t reserved_20_63:44;
+#endif
+	} s;
+};
+
+union cvmx_mixx_irhwm {
+	uint64_t u64;
+	struct cvmx_mixx_irhwm_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_40_63:24;
+		uint64_t ibplwm:20;
+		uint64_t irhwm:20;
+#else
+		uint64_t irhwm:20;
+		uint64_t ibplwm:20;
+		uint64_t reserved_40_63:24;
+#endif
+	} s;
+};
+
+union cvmx_mixx_iring1 {
+	uint64_t u64;
+	struct cvmx_mixx_iring1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_60_63:4;
+		uint64_t isize:20;
+		uint64_t ibase:37;
+		uint64_t reserved_0_2:3;
+#else
+		uint64_t reserved_0_2:3;
+		uint64_t ibase:37;
+		uint64_t isize:20;
+		uint64_t reserved_60_63:4;
+#endif
+	} s;
+	struct cvmx_mixx_iring1_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_60_63:4;
+		uint64_t isize:20;
+		uint64_t reserved_36_39:4;
+		uint64_t ibase:33;
+		uint64_t reserved_0_2:3;
+#else
+		uint64_t reserved_0_2:3;
+		uint64_t ibase:33;
+		uint64_t reserved_36_39:4;
+		uint64_t isize:20;
+		uint64_t reserved_60_63:4;
+#endif
+	} cn52xx;
+};
+
+union cvmx_mixx_iring2 {
+	uint64_t u64;
+	struct cvmx_mixx_iring2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_52_63:12;
+		uint64_t itlptr:20;
+		uint64_t reserved_20_31:12;
+		uint64_t idbell:20;
+#else
+		uint64_t idbell:20;
+		uint64_t reserved_20_31:12;
+		uint64_t itlptr:20;
+		uint64_t reserved_52_63:12;
+#endif
+	} s;
+};
+
+union cvmx_mixx_isr {
+	uint64_t u64;
+	struct cvmx_mixx_isr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t ts:1;
+		uint64_t orun:1;
+		uint64_t irun:1;
+		uint64_t data_drp:1;
+		uint64_t irthresh:1;
+		uint64_t orthresh:1;
+		uint64_t idblovf:1;
+		uint64_t odblovf:1;
+#else
+		uint64_t odblovf:1;
+		uint64_t idblovf:1;
+		uint64_t orthresh:1;
+		uint64_t irthresh:1;
+		uint64_t data_drp:1;
+		uint64_t irun:1;
+		uint64_t orun:1;
+		uint64_t ts:1;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+	struct cvmx_mixx_isr_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t orun:1;
+		uint64_t irun:1;
+		uint64_t data_drp:1;
+		uint64_t irthresh:1;
+		uint64_t orthresh:1;
+		uint64_t idblovf:1;
+		uint64_t odblovf:1;
+#else
+		uint64_t odblovf:1;
+		uint64_t idblovf:1;
+		uint64_t orthresh:1;
+		uint64_t irthresh:1;
+		uint64_t data_drp:1;
+		uint64_t irun:1;
+		uint64_t orun:1;
+		uint64_t reserved_7_63:57;
+#endif
+	} cn52xx;
+};
+
+union cvmx_mixx_orcnt {
+	uint64_t u64;
+	struct cvmx_mixx_orcnt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t orcnt:20;
+#else
+		uint64_t orcnt:20;
+		uint64_t reserved_20_63:44;
+#endif
+	} s;
+};
+
+union cvmx_mixx_orhwm {
+	uint64_t u64;
+	struct cvmx_mixx_orhwm_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t orhwm:20;
+#else
+		uint64_t orhwm:20;
+		uint64_t reserved_20_63:44;
+#endif
+	} s;
+};
+
+union cvmx_mixx_oring1 {
+	uint64_t u64;
+	struct cvmx_mixx_oring1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_60_63:4;
+		uint64_t osize:20;
+		uint64_t obase:37;
+		uint64_t reserved_0_2:3;
+#else
+		uint64_t reserved_0_2:3;
+		uint64_t obase:37;
+		uint64_t osize:20;
+		uint64_t reserved_60_63:4;
+#endif
+	} s;
+	struct cvmx_mixx_oring1_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_60_63:4;
+		uint64_t osize:20;
+		uint64_t reserved_36_39:4;
+		uint64_t obase:33;
+		uint64_t reserved_0_2:3;
+#else
+		uint64_t reserved_0_2:3;
+		uint64_t obase:33;
+		uint64_t reserved_36_39:4;
+		uint64_t osize:20;
+		uint64_t reserved_60_63:4;
+#endif
+	} cn52xx;
+};
+
+union cvmx_mixx_oring2 {
+	uint64_t u64;
+	struct cvmx_mixx_oring2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_52_63:12;
+		uint64_t otlptr:20;
+		uint64_t reserved_20_31:12;
+		uint64_t odbell:20;
+#else
+		uint64_t odbell:20;
+		uint64_t reserved_20_31:12;
+		uint64_t otlptr:20;
+		uint64_t reserved_52_63:12;
+#endif
+	} s;
+};
+
+union cvmx_mixx_remcnt {
+	uint64_t u64;
+	struct cvmx_mixx_remcnt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_52_63:12;
+		uint64_t iremcnt:20;
+		uint64_t reserved_20_31:12;
+		uint64_t oremcnt:20;
+#else
+		uint64_t oremcnt:20;
+		uint64_t reserved_20_31:12;
+		uint64_t iremcnt:20;
+		uint64_t reserved_52_63:12;
+#endif
+	} s;
+};
+
+union cvmx_mixx_tsctl {
+	uint64_t u64;
+	struct cvmx_mixx_tsctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_21_63:43;
+		uint64_t tsavl:5;
+		uint64_t reserved_13_15:3;
+		uint64_t tstot:5;
+		uint64_t reserved_5_7:3;
+		uint64_t tscnt:5;
+#else
+		uint64_t tscnt:5;
+		uint64_t reserved_5_7:3;
+		uint64_t tstot:5;
+		uint64_t reserved_13_15:3;
+		uint64_t tsavl:5;
+		uint64_t reserved_21_63:43;
+#endif
+	} s;
+};
+
+union cvmx_mixx_tstamp {
+	uint64_t u64;
+	struct cvmx_mixx_tstamp_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t tstamp:64;
+#else
+		uint64_t tstamp:64;
+#endif
+	} s;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-npei-defs.h b/arch/mips/include/asm/octeon/cvmx-npei-defs.h
new file mode 100644
index 000000000..6a51b1ef8
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-npei-defs.h
@@ -0,0 +1,3925 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2012 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_NPEI_DEFS_H__
+#define __CVMX_NPEI_DEFS_H__
+
+#define CVMX_NPEI_BAR1_INDEXX(offset) (0x0000000000000000ull + ((offset) & 31) * 16)
+#define CVMX_NPEI_BIST_STATUS (0x0000000000000580ull)
+#define CVMX_NPEI_BIST_STATUS2 (0x0000000000000680ull)
+#define CVMX_NPEI_CTL_PORT0 (0x0000000000000250ull)
+#define CVMX_NPEI_CTL_PORT1 (0x0000000000000260ull)
+#define CVMX_NPEI_CTL_STATUS (0x0000000000000570ull)
+#define CVMX_NPEI_CTL_STATUS2 (0x0000000000003C00ull)
+#define CVMX_NPEI_DATA_OUT_CNT (0x00000000000005F0ull)
+#define CVMX_NPEI_DBG_DATA (0x0000000000000510ull)
+#define CVMX_NPEI_DBG_SELECT (0x0000000000000500ull)
+#define CVMX_NPEI_DMA0_INT_LEVEL (0x00000000000005C0ull)
+#define CVMX_NPEI_DMA1_INT_LEVEL (0x00000000000005D0ull)
+#define CVMX_NPEI_DMAX_COUNTS(offset) (0x0000000000000450ull + ((offset) & 7) * 16)
+#define CVMX_NPEI_DMAX_DBELL(offset) (0x00000000000003B0ull + ((offset) & 7) * 16)
+#define CVMX_NPEI_DMAX_IBUFF_SADDR(offset) (0x0000000000000400ull + ((offset) & 7) * 16)
+#define CVMX_NPEI_DMAX_NADDR(offset) (0x00000000000004A0ull + ((offset) & 7) * 16)
+#define CVMX_NPEI_DMA_CNTS (0x00000000000005E0ull)
+#define CVMX_NPEI_DMA_CONTROL (0x00000000000003A0ull)
+#define CVMX_NPEI_DMA_PCIE_REQ_NUM (0x00000000000005B0ull)
+#define CVMX_NPEI_DMA_STATE1 (0x00000000000006C0ull)
+#define CVMX_NPEI_DMA_STATE1_P1 (0x0000000000000680ull)
+#define CVMX_NPEI_DMA_STATE2 (0x00000000000006D0ull)
+#define CVMX_NPEI_DMA_STATE2_P1 (0x0000000000000690ull)
+#define CVMX_NPEI_DMA_STATE3_P1 (0x00000000000006A0ull)
+#define CVMX_NPEI_DMA_STATE4_P1 (0x00000000000006B0ull)
+#define CVMX_NPEI_DMA_STATE5_P1 (0x00000000000006C0ull)
+#define CVMX_NPEI_INT_A_ENB (0x0000000000000560ull)
+#define CVMX_NPEI_INT_A_ENB2 (0x0000000000003CE0ull)
+#define CVMX_NPEI_INT_A_SUM (0x0000000000000550ull)
+#define CVMX_NPEI_INT_ENB (0x0000000000000540ull)
+#define CVMX_NPEI_INT_ENB2 (0x0000000000003CD0ull)
+#define CVMX_NPEI_INT_INFO (0x0000000000000590ull)
+#define CVMX_NPEI_INT_SUM (0x0000000000000530ull)
+#define CVMX_NPEI_INT_SUM2 (0x0000000000003CC0ull)
+#define CVMX_NPEI_LAST_WIN_RDATA0 (0x0000000000000600ull)
+#define CVMX_NPEI_LAST_WIN_RDATA1 (0x0000000000000610ull)
+#define CVMX_NPEI_MEM_ACCESS_CTL (0x00000000000004F0ull)
+#define CVMX_NPEI_MEM_ACCESS_SUBIDX(offset) (0x0000000000000280ull + ((offset) & 31) * 16 - 16*12)
+#define CVMX_NPEI_MSI_ENB0 (0x0000000000003C50ull)
+#define CVMX_NPEI_MSI_ENB1 (0x0000000000003C60ull)
+#define CVMX_NPEI_MSI_ENB2 (0x0000000000003C70ull)
+#define CVMX_NPEI_MSI_ENB3 (0x0000000000003C80ull)
+#define CVMX_NPEI_MSI_RCV0 (0x0000000000003C10ull)
+#define CVMX_NPEI_MSI_RCV1 (0x0000000000003C20ull)
+#define CVMX_NPEI_MSI_RCV2 (0x0000000000003C30ull)
+#define CVMX_NPEI_MSI_RCV3 (0x0000000000003C40ull)
+#define CVMX_NPEI_MSI_RD_MAP (0x0000000000003CA0ull)
+#define CVMX_NPEI_MSI_W1C_ENB0 (0x0000000000003CF0ull)
+#define CVMX_NPEI_MSI_W1C_ENB1 (0x0000000000003D00ull)
+#define CVMX_NPEI_MSI_W1C_ENB2 (0x0000000000003D10ull)
+#define CVMX_NPEI_MSI_W1C_ENB3 (0x0000000000003D20ull)
+#define CVMX_NPEI_MSI_W1S_ENB0 (0x0000000000003D30ull)
+#define CVMX_NPEI_MSI_W1S_ENB1 (0x0000000000003D40ull)
+#define CVMX_NPEI_MSI_W1S_ENB2 (0x0000000000003D50ull)
+#define CVMX_NPEI_MSI_W1S_ENB3 (0x0000000000003D60ull)
+#define CVMX_NPEI_MSI_WR_MAP (0x0000000000003C90ull)
+#define CVMX_NPEI_PCIE_CREDIT_CNT (0x0000000000003D70ull)
+#define CVMX_NPEI_PCIE_MSI_RCV (0x0000000000003CB0ull)
+#define CVMX_NPEI_PCIE_MSI_RCV_B1 (0x0000000000000650ull)
+#define CVMX_NPEI_PCIE_MSI_RCV_B2 (0x0000000000000660ull)
+#define CVMX_NPEI_PCIE_MSI_RCV_B3 (0x0000000000000670ull)
+#define CVMX_NPEI_PKTX_CNTS(offset) (0x0000000000002400ull + ((offset) & 31) * 16)
+#define CVMX_NPEI_PKTX_INSTR_BADDR(offset) (0x0000000000002800ull + ((offset) & 31) * 16)
+#define CVMX_NPEI_PKTX_INSTR_BAOFF_DBELL(offset) (0x0000000000002C00ull + ((offset) & 31) * 16)
+#define CVMX_NPEI_PKTX_INSTR_FIFO_RSIZE(offset) (0x0000000000003000ull + ((offset) & 31) * 16)
+#define CVMX_NPEI_PKTX_INSTR_HEADER(offset) (0x0000000000003400ull + ((offset) & 31) * 16)
+#define CVMX_NPEI_PKTX_IN_BP(offset) (0x0000000000003800ull + ((offset) & 31) * 16)
+#define CVMX_NPEI_PKTX_SLIST_BADDR(offset) (0x0000000000001400ull + ((offset) & 31) * 16)
+#define CVMX_NPEI_PKTX_SLIST_BAOFF_DBELL(offset) (0x0000000000001800ull + ((offset) & 31) * 16)
+#define CVMX_NPEI_PKTX_SLIST_FIFO_RSIZE(offset) (0x0000000000001C00ull + ((offset) & 31) * 16)
+#define CVMX_NPEI_PKT_CNT_INT (0x0000000000001110ull)
+#define CVMX_NPEI_PKT_CNT_INT_ENB (0x0000000000001130ull)
+#define CVMX_NPEI_PKT_DATA_OUT_ES (0x00000000000010B0ull)
+#define CVMX_NPEI_PKT_DATA_OUT_NS (0x00000000000010A0ull)
+#define CVMX_NPEI_PKT_DATA_OUT_ROR (0x0000000000001090ull)
+#define CVMX_NPEI_PKT_DPADDR (0x0000000000001080ull)
+#define CVMX_NPEI_PKT_INPUT_CONTROL (0x0000000000001150ull)
+#define CVMX_NPEI_PKT_INSTR_ENB (0x0000000000001000ull)
+#define CVMX_NPEI_PKT_INSTR_RD_SIZE (0x0000000000001190ull)
+#define CVMX_NPEI_PKT_INSTR_SIZE (0x0000000000001020ull)
+#define CVMX_NPEI_PKT_INT_LEVELS (0x0000000000001100ull)
+#define CVMX_NPEI_PKT_IN_BP (0x00000000000006B0ull)
+#define CVMX_NPEI_PKT_IN_DONEX_CNTS(offset) (0x0000000000002000ull + ((offset) & 31) * 16)
+#define CVMX_NPEI_PKT_IN_INSTR_COUNTS (0x00000000000006A0ull)
+#define CVMX_NPEI_PKT_IN_PCIE_PORT (0x00000000000011A0ull)
+#define CVMX_NPEI_PKT_IPTR (0x0000000000001070ull)
+#define CVMX_NPEI_PKT_OUTPUT_WMARK (0x0000000000001160ull)
+#define CVMX_NPEI_PKT_OUT_BMODE (0x00000000000010D0ull)
+#define CVMX_NPEI_PKT_OUT_ENB (0x0000000000001010ull)
+#define CVMX_NPEI_PKT_PCIE_PORT (0x00000000000010E0ull)
+#define CVMX_NPEI_PKT_PORT_IN_RST (0x0000000000000690ull)
+#define CVMX_NPEI_PKT_SLIST_ES (0x0000000000001050ull)
+#define CVMX_NPEI_PKT_SLIST_ID_SIZE (0x0000000000001180ull)
+#define CVMX_NPEI_PKT_SLIST_NS (0x0000000000001040ull)
+#define CVMX_NPEI_PKT_SLIST_ROR (0x0000000000001030ull)
+#define CVMX_NPEI_PKT_TIME_INT (0x0000000000001120ull)
+#define CVMX_NPEI_PKT_TIME_INT_ENB (0x0000000000001140ull)
+#define CVMX_NPEI_RSL_INT_BLOCKS (0x0000000000000520ull)
+#define CVMX_NPEI_SCRATCH_1 (0x0000000000000270ull)
+#define CVMX_NPEI_STATE1 (0x0000000000000620ull)
+#define CVMX_NPEI_STATE2 (0x0000000000000630ull)
+#define CVMX_NPEI_STATE3 (0x0000000000000640ull)
+#define CVMX_NPEI_WINDOW_CTL (0x0000000000000380ull)
+#define CVMX_NPEI_WIN_RD_ADDR (0x0000000000000210ull)
+#define CVMX_NPEI_WIN_RD_DATA (0x0000000000000240ull)
+#define CVMX_NPEI_WIN_WR_ADDR (0x0000000000000200ull)
+#define CVMX_NPEI_WIN_WR_DATA (0x0000000000000220ull)
+#define CVMX_NPEI_WIN_WR_MASK (0x0000000000000230ull)
+
+union cvmx_npei_bar1_indexx {
+	uint32_t u32;
+	struct cvmx_npei_bar1_indexx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t reserved_18_31:14;
+		uint32_t addr_idx:14;
+		uint32_t ca:1;
+		uint32_t end_swp:2;
+		uint32_t addr_v:1;
+#else
+		uint32_t addr_v:1;
+		uint32_t end_swp:2;
+		uint32_t ca:1;
+		uint32_t addr_idx:14;
+		uint32_t reserved_18_31:14;
+#endif
+	} s;
+};
+
+union cvmx_npei_bist_status {
+	uint64_t u64;
+	struct cvmx_npei_bist_status_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t pkt_rdf:1;
+		uint64_t reserved_60_62:3;
+		uint64_t pcr_gim:1;
+		uint64_t pkt_pif:1;
+		uint64_t pcsr_int:1;
+		uint64_t pcsr_im:1;
+		uint64_t pcsr_cnt:1;
+		uint64_t pcsr_id:1;
+		uint64_t pcsr_sl:1;
+		uint64_t reserved_50_52:3;
+		uint64_t pkt_ind:1;
+		uint64_t pkt_slm:1;
+		uint64_t reserved_36_47:12;
+		uint64_t d0_pst:1;
+		uint64_t d1_pst:1;
+		uint64_t d2_pst:1;
+		uint64_t d3_pst:1;
+		uint64_t reserved_31_31:1;
+		uint64_t n2p0_c:1;
+		uint64_t n2p0_o:1;
+		uint64_t n2p1_c:1;
+		uint64_t n2p1_o:1;
+		uint64_t cpl_p0:1;
+		uint64_t cpl_p1:1;
+		uint64_t p2n1_po:1;
+		uint64_t p2n1_no:1;
+		uint64_t p2n1_co:1;
+		uint64_t p2n0_po:1;
+		uint64_t p2n0_no:1;
+		uint64_t p2n0_co:1;
+		uint64_t p2n0_c0:1;
+		uint64_t p2n0_c1:1;
+		uint64_t p2n0_n:1;
+		uint64_t p2n0_p0:1;
+		uint64_t p2n0_p1:1;
+		uint64_t p2n1_c0:1;
+		uint64_t p2n1_c1:1;
+		uint64_t p2n1_n:1;
+		uint64_t p2n1_p0:1;
+		uint64_t p2n1_p1:1;
+		uint64_t csm0:1;
+		uint64_t csm1:1;
+		uint64_t dif0:1;
+		uint64_t dif1:1;
+		uint64_t dif2:1;
+		uint64_t dif3:1;
+		uint64_t reserved_2_2:1;
+		uint64_t msi:1;
+		uint64_t ncb_cmd:1;
+#else
+		uint64_t ncb_cmd:1;
+		uint64_t msi:1;
+		uint64_t reserved_2_2:1;
+		uint64_t dif3:1;
+		uint64_t dif2:1;
+		uint64_t dif1:1;
+		uint64_t dif0:1;
+		uint64_t csm1:1;
+		uint64_t csm0:1;
+		uint64_t p2n1_p1:1;
+		uint64_t p2n1_p0:1;
+		uint64_t p2n1_n:1;
+		uint64_t p2n1_c1:1;
+		uint64_t p2n1_c0:1;
+		uint64_t p2n0_p1:1;
+		uint64_t p2n0_p0:1;
+		uint64_t p2n0_n:1;
+		uint64_t p2n0_c1:1;
+		uint64_t p2n0_c0:1;
+		uint64_t p2n0_co:1;
+		uint64_t p2n0_no:1;
+		uint64_t p2n0_po:1;
+		uint64_t p2n1_co:1;
+		uint64_t p2n1_no:1;
+		uint64_t p2n1_po:1;
+		uint64_t cpl_p1:1;
+		uint64_t cpl_p0:1;
+		uint64_t n2p1_o:1;
+		uint64_t n2p1_c:1;
+		uint64_t n2p0_o:1;
+		uint64_t n2p0_c:1;
+		uint64_t reserved_31_31:1;
+		uint64_t d3_pst:1;
+		uint64_t d2_pst:1;
+		uint64_t d1_pst:1;
+		uint64_t d0_pst:1;
+		uint64_t reserved_36_47:12;
+		uint64_t pkt_slm:1;
+		uint64_t pkt_ind:1;
+		uint64_t reserved_50_52:3;
+		uint64_t pcsr_sl:1;
+		uint64_t pcsr_id:1;
+		uint64_t pcsr_cnt:1;
+		uint64_t pcsr_im:1;
+		uint64_t pcsr_int:1;
+		uint64_t pkt_pif:1;
+		uint64_t pcr_gim:1;
+		uint64_t reserved_60_62:3;
+		uint64_t pkt_rdf:1;
+#endif
+	} s;
+	struct cvmx_npei_bist_status_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t pkt_rdf:1;
+		uint64_t reserved_60_62:3;
+		uint64_t pcr_gim:1;
+		uint64_t pkt_pif:1;
+		uint64_t pcsr_int:1;
+		uint64_t pcsr_im:1;
+		uint64_t pcsr_cnt:1;
+		uint64_t pcsr_id:1;
+		uint64_t pcsr_sl:1;
+		uint64_t pkt_imem:1;
+		uint64_t pkt_pfm:1;
+		uint64_t pkt_pof:1;
+		uint64_t reserved_48_49:2;
+		uint64_t pkt_pop0:1;
+		uint64_t pkt_pop1:1;
+		uint64_t d0_mem:1;
+		uint64_t d1_mem:1;
+		uint64_t d2_mem:1;
+		uint64_t d3_mem:1;
+		uint64_t d4_mem:1;
+		uint64_t ds_mem:1;
+		uint64_t reserved_36_39:4;
+		uint64_t d0_pst:1;
+		uint64_t d1_pst:1;
+		uint64_t d2_pst:1;
+		uint64_t d3_pst:1;
+		uint64_t d4_pst:1;
+		uint64_t n2p0_c:1;
+		uint64_t n2p0_o:1;
+		uint64_t n2p1_c:1;
+		uint64_t n2p1_o:1;
+		uint64_t cpl_p0:1;
+		uint64_t cpl_p1:1;
+		uint64_t p2n1_po:1;
+		uint64_t p2n1_no:1;
+		uint64_t p2n1_co:1;
+		uint64_t p2n0_po:1;
+		uint64_t p2n0_no:1;
+		uint64_t p2n0_co:1;
+		uint64_t p2n0_c0:1;
+		uint64_t p2n0_c1:1;
+		uint64_t p2n0_n:1;
+		uint64_t p2n0_p0:1;
+		uint64_t p2n0_p1:1;
+		uint64_t p2n1_c0:1;
+		uint64_t p2n1_c1:1;
+		uint64_t p2n1_n:1;
+		uint64_t p2n1_p0:1;
+		uint64_t p2n1_p1:1;
+		uint64_t csm0:1;
+		uint64_t csm1:1;
+		uint64_t dif0:1;
+		uint64_t dif1:1;
+		uint64_t dif2:1;
+		uint64_t dif3:1;
+		uint64_t dif4:1;
+		uint64_t msi:1;
+		uint64_t ncb_cmd:1;
+#else
+		uint64_t ncb_cmd:1;
+		uint64_t msi:1;
+		uint64_t dif4:1;
+		uint64_t dif3:1;
+		uint64_t dif2:1;
+		uint64_t dif1:1;
+		uint64_t dif0:1;
+		uint64_t csm1:1;
+		uint64_t csm0:1;
+		uint64_t p2n1_p1:1;
+		uint64_t p2n1_p0:1;
+		uint64_t p2n1_n:1;
+		uint64_t p2n1_c1:1;
+		uint64_t p2n1_c0:1;
+		uint64_t p2n0_p1:1;
+		uint64_t p2n0_p0:1;
+		uint64_t p2n0_n:1;
+		uint64_t p2n0_c1:1;
+		uint64_t p2n0_c0:1;
+		uint64_t p2n0_co:1;
+		uint64_t p2n0_no:1;
+		uint64_t p2n0_po:1;
+		uint64_t p2n1_co:1;
+		uint64_t p2n1_no:1;
+		uint64_t p2n1_po:1;
+		uint64_t cpl_p1:1;
+		uint64_t cpl_p0:1;
+		uint64_t n2p1_o:1;
+		uint64_t n2p1_c:1;
+		uint64_t n2p0_o:1;
+		uint64_t n2p0_c:1;
+		uint64_t d4_pst:1;
+		uint64_t d3_pst:1;
+		uint64_t d2_pst:1;
+		uint64_t d1_pst:1;
+		uint64_t d0_pst:1;
+		uint64_t reserved_36_39:4;
+		uint64_t ds_mem:1;
+		uint64_t d4_mem:1;
+		uint64_t d3_mem:1;
+		uint64_t d2_mem:1;
+		uint64_t d1_mem:1;
+		uint64_t d0_mem:1;
+		uint64_t pkt_pop1:1;
+		uint64_t pkt_pop0:1;
+		uint64_t reserved_48_49:2;
+		uint64_t pkt_pof:1;
+		uint64_t pkt_pfm:1;
+		uint64_t pkt_imem:1;
+		uint64_t pcsr_sl:1;
+		uint64_t pcsr_id:1;
+		uint64_t pcsr_cnt:1;
+		uint64_t pcsr_im:1;
+		uint64_t pcsr_int:1;
+		uint64_t pkt_pif:1;
+		uint64_t pcr_gim:1;
+		uint64_t reserved_60_62:3;
+		uint64_t pkt_rdf:1;
+#endif
+	} cn52xx;
+	struct cvmx_npei_bist_status_cn52xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_46_63:18;
+		uint64_t d0_mem0:1;
+		uint64_t d1_mem1:1;
+		uint64_t d2_mem2:1;
+		uint64_t d3_mem3:1;
+		uint64_t dr0_mem:1;
+		uint64_t d0_mem:1;
+		uint64_t d1_mem:1;
+		uint64_t d2_mem:1;
+		uint64_t d3_mem:1;
+		uint64_t dr1_mem:1;
+		uint64_t d0_pst:1;
+		uint64_t d1_pst:1;
+		uint64_t d2_pst:1;
+		uint64_t d3_pst:1;
+		uint64_t dr2_mem:1;
+		uint64_t n2p0_c:1;
+		uint64_t n2p0_o:1;
+		uint64_t n2p1_c:1;
+		uint64_t n2p1_o:1;
+		uint64_t cpl_p0:1;
+		uint64_t cpl_p1:1;
+		uint64_t p2n1_po:1;
+		uint64_t p2n1_no:1;
+		uint64_t p2n1_co:1;
+		uint64_t p2n0_po:1;
+		uint64_t p2n0_no:1;
+		uint64_t p2n0_co:1;
+		uint64_t p2n0_c0:1;
+		uint64_t p2n0_c1:1;
+		uint64_t p2n0_n:1;
+		uint64_t p2n0_p0:1;
+		uint64_t p2n0_p1:1;
+		uint64_t p2n1_c0:1;
+		uint64_t p2n1_c1:1;
+		uint64_t p2n1_n:1;
+		uint64_t p2n1_p0:1;
+		uint64_t p2n1_p1:1;
+		uint64_t csm0:1;
+		uint64_t csm1:1;
+		uint64_t dif0:1;
+		uint64_t dif1:1;
+		uint64_t dif2:1;
+		uint64_t dif3:1;
+		uint64_t dr3_mem:1;
+		uint64_t msi:1;
+		uint64_t ncb_cmd:1;
+#else
+		uint64_t ncb_cmd:1;
+		uint64_t msi:1;
+		uint64_t dr3_mem:1;
+		uint64_t dif3:1;
+		uint64_t dif2:1;
+		uint64_t dif1:1;
+		uint64_t dif0:1;
+		uint64_t csm1:1;
+		uint64_t csm0:1;
+		uint64_t p2n1_p1:1;
+		uint64_t p2n1_p0:1;
+		uint64_t p2n1_n:1;
+		uint64_t p2n1_c1:1;
+		uint64_t p2n1_c0:1;
+		uint64_t p2n0_p1:1;
+		uint64_t p2n0_p0:1;
+		uint64_t p2n0_n:1;
+		uint64_t p2n0_c1:1;
+		uint64_t p2n0_c0:1;
+		uint64_t p2n0_co:1;
+		uint64_t p2n0_no:1;
+		uint64_t p2n0_po:1;
+		uint64_t p2n1_co:1;
+		uint64_t p2n1_no:1;
+		uint64_t p2n1_po:1;
+		uint64_t cpl_p1:1;
+		uint64_t cpl_p0:1;
+		uint64_t n2p1_o:1;
+		uint64_t n2p1_c:1;
+		uint64_t n2p0_o:1;
+		uint64_t n2p0_c:1;
+		uint64_t dr2_mem:1;
+		uint64_t d3_pst:1;
+		uint64_t d2_pst:1;
+		uint64_t d1_pst:1;
+		uint64_t d0_pst:1;
+		uint64_t dr1_mem:1;
+		uint64_t d3_mem:1;
+		uint64_t d2_mem:1;
+		uint64_t d1_mem:1;
+		uint64_t d0_mem:1;
+		uint64_t dr0_mem:1;
+		uint64_t d3_mem3:1;
+		uint64_t d2_mem2:1;
+		uint64_t d1_mem1:1;
+		uint64_t d0_mem0:1;
+		uint64_t reserved_46_63:18;
+#endif
+	} cn52xxp1;
+	struct cvmx_npei_bist_status_cn56xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_58_63:6;
+		uint64_t pcsr_int:1;
+		uint64_t pcsr_im:1;
+		uint64_t pcsr_cnt:1;
+		uint64_t pcsr_id:1;
+		uint64_t pcsr_sl:1;
+		uint64_t pkt_pout:1;
+		uint64_t pkt_imem:1;
+		uint64_t pkt_cntm:1;
+		uint64_t pkt_ind:1;
+		uint64_t pkt_slm:1;
+		uint64_t pkt_odf:1;
+		uint64_t pkt_oif:1;
+		uint64_t pkt_out:1;
+		uint64_t pkt_i0:1;
+		uint64_t pkt_i1:1;
+		uint64_t pkt_s0:1;
+		uint64_t pkt_s1:1;
+		uint64_t d0_mem:1;
+		uint64_t d1_mem:1;
+		uint64_t d2_mem:1;
+		uint64_t d3_mem:1;
+		uint64_t d4_mem:1;
+		uint64_t d0_pst:1;
+		uint64_t d1_pst:1;
+		uint64_t d2_pst:1;
+		uint64_t d3_pst:1;
+		uint64_t d4_pst:1;
+		uint64_t n2p0_c:1;
+		uint64_t n2p0_o:1;
+		uint64_t n2p1_c:1;
+		uint64_t n2p1_o:1;
+		uint64_t cpl_p0:1;
+		uint64_t cpl_p1:1;
+		uint64_t p2n1_po:1;
+		uint64_t p2n1_no:1;
+		uint64_t p2n1_co:1;
+		uint64_t p2n0_po:1;
+		uint64_t p2n0_no:1;
+		uint64_t p2n0_co:1;
+		uint64_t p2n0_c0:1;
+		uint64_t p2n0_c1:1;
+		uint64_t p2n0_n:1;
+		uint64_t p2n0_p0:1;
+		uint64_t p2n0_p1:1;
+		uint64_t p2n1_c0:1;
+		uint64_t p2n1_c1:1;
+		uint64_t p2n1_n:1;
+		uint64_t p2n1_p0:1;
+		uint64_t p2n1_p1:1;
+		uint64_t csm0:1;
+		uint64_t csm1:1;
+		uint64_t dif0:1;
+		uint64_t dif1:1;
+		uint64_t dif2:1;
+		uint64_t dif3:1;
+		uint64_t dif4:1;
+		uint64_t msi:1;
+		uint64_t ncb_cmd:1;
+#else
+		uint64_t ncb_cmd:1;
+		uint64_t msi:1;
+		uint64_t dif4:1;
+		uint64_t dif3:1;
+		uint64_t dif2:1;
+		uint64_t dif1:1;
+		uint64_t dif0:1;
+		uint64_t csm1:1;
+		uint64_t csm0:1;
+		uint64_t p2n1_p1:1;
+		uint64_t p2n1_p0:1;
+		uint64_t p2n1_n:1;
+		uint64_t p2n1_c1:1;
+		uint64_t p2n1_c0:1;
+		uint64_t p2n0_p1:1;
+		uint64_t p2n0_p0:1;
+		uint64_t p2n0_n:1;
+		uint64_t p2n0_c1:1;
+		uint64_t p2n0_c0:1;
+		uint64_t p2n0_co:1;
+		uint64_t p2n0_no:1;
+		uint64_t p2n0_po:1;
+		uint64_t p2n1_co:1;
+		uint64_t p2n1_no:1;
+		uint64_t p2n1_po:1;
+		uint64_t cpl_p1:1;
+		uint64_t cpl_p0:1;
+		uint64_t n2p1_o:1;
+		uint64_t n2p1_c:1;
+		uint64_t n2p0_o:1;
+		uint64_t n2p0_c:1;
+		uint64_t d4_pst:1;
+		uint64_t d3_pst:1;
+		uint64_t d2_pst:1;
+		uint64_t d1_pst:1;
+		uint64_t d0_pst:1;
+		uint64_t d4_mem:1;
+		uint64_t d3_mem:1;
+		uint64_t d2_mem:1;
+		uint64_t d1_mem:1;
+		uint64_t d0_mem:1;
+		uint64_t pkt_s1:1;
+		uint64_t pkt_s0:1;
+		uint64_t pkt_i1:1;
+		uint64_t pkt_i0:1;
+		uint64_t pkt_out:1;
+		uint64_t pkt_oif:1;
+		uint64_t pkt_odf:1;
+		uint64_t pkt_slm:1;
+		uint64_t pkt_ind:1;
+		uint64_t pkt_cntm:1;
+		uint64_t pkt_imem:1;
+		uint64_t pkt_pout:1;
+		uint64_t pcsr_sl:1;
+		uint64_t pcsr_id:1;
+		uint64_t pcsr_cnt:1;
+		uint64_t pcsr_im:1;
+		uint64_t pcsr_int:1;
+		uint64_t reserved_58_63:6;
+#endif
+	} cn56xxp1;
+};
+
+union cvmx_npei_bist_status2 {
+	uint64_t u64;
+	struct cvmx_npei_bist_status2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_14_63:50;
+		uint64_t prd_tag:1;
+		uint64_t prd_st0:1;
+		uint64_t prd_st1:1;
+		uint64_t prd_err:1;
+		uint64_t nrd_st:1;
+		uint64_t nwe_st:1;
+		uint64_t nwe_wr0:1;
+		uint64_t nwe_wr1:1;
+		uint64_t pkt_rd:1;
+		uint64_t psc_p0:1;
+		uint64_t psc_p1:1;
+		uint64_t pkt_gd:1;
+		uint64_t pkt_gl:1;
+		uint64_t pkt_blk:1;
+#else
+		uint64_t pkt_blk:1;
+		uint64_t pkt_gl:1;
+		uint64_t pkt_gd:1;
+		uint64_t psc_p1:1;
+		uint64_t psc_p0:1;
+		uint64_t pkt_rd:1;
+		uint64_t nwe_wr1:1;
+		uint64_t nwe_wr0:1;
+		uint64_t nwe_st:1;
+		uint64_t nrd_st:1;
+		uint64_t prd_err:1;
+		uint64_t prd_st1:1;
+		uint64_t prd_st0:1;
+		uint64_t prd_tag:1;
+		uint64_t reserved_14_63:50;
+#endif
+	} s;
+};
+
+union cvmx_npei_ctl_port0 {
+	uint64_t u64;
+	struct cvmx_npei_ctl_port0_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_21_63:43;
+		uint64_t waitl_com:1;
+		uint64_t intd:1;
+		uint64_t intc:1;
+		uint64_t intb:1;
+		uint64_t inta:1;
+		uint64_t intd_map:2;
+		uint64_t intc_map:2;
+		uint64_t intb_map:2;
+		uint64_t inta_map:2;
+		uint64_t ctlp_ro:1;
+		uint64_t reserved_6_6:1;
+		uint64_t ptlp_ro:1;
+		uint64_t bar2_enb:1;
+		uint64_t bar2_esx:2;
+		uint64_t bar2_cax:1;
+		uint64_t wait_com:1;
+#else
+		uint64_t wait_com:1;
+		uint64_t bar2_cax:1;
+		uint64_t bar2_esx:2;
+		uint64_t bar2_enb:1;
+		uint64_t ptlp_ro:1;
+		uint64_t reserved_6_6:1;
+		uint64_t ctlp_ro:1;
+		uint64_t inta_map:2;
+		uint64_t intb_map:2;
+		uint64_t intc_map:2;
+		uint64_t intd_map:2;
+		uint64_t inta:1;
+		uint64_t intb:1;
+		uint64_t intc:1;
+		uint64_t intd:1;
+		uint64_t waitl_com:1;
+		uint64_t reserved_21_63:43;
+#endif
+	} s;
+};
+
+union cvmx_npei_ctl_port1 {
+	uint64_t u64;
+	struct cvmx_npei_ctl_port1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_21_63:43;
+		uint64_t waitl_com:1;
+		uint64_t intd:1;
+		uint64_t intc:1;
+		uint64_t intb:1;
+		uint64_t inta:1;
+		uint64_t intd_map:2;
+		uint64_t intc_map:2;
+		uint64_t intb_map:2;
+		uint64_t inta_map:2;
+		uint64_t ctlp_ro:1;
+		uint64_t reserved_6_6:1;
+		uint64_t ptlp_ro:1;
+		uint64_t bar2_enb:1;
+		uint64_t bar2_esx:2;
+		uint64_t bar2_cax:1;
+		uint64_t wait_com:1;
+#else
+		uint64_t wait_com:1;
+		uint64_t bar2_cax:1;
+		uint64_t bar2_esx:2;
+		uint64_t bar2_enb:1;
+		uint64_t ptlp_ro:1;
+		uint64_t reserved_6_6:1;
+		uint64_t ctlp_ro:1;
+		uint64_t inta_map:2;
+		uint64_t intb_map:2;
+		uint64_t intc_map:2;
+		uint64_t intd_map:2;
+		uint64_t inta:1;
+		uint64_t intb:1;
+		uint64_t intc:1;
+		uint64_t intd:1;
+		uint64_t waitl_com:1;
+		uint64_t reserved_21_63:43;
+#endif
+	} s;
+};
+
+union cvmx_npei_ctl_status {
+	uint64_t u64;
+	struct cvmx_npei_ctl_status_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_44_63:20;
+		uint64_t p1_ntags:6;
+		uint64_t p0_ntags:6;
+		uint64_t cfg_rtry:16;
+		uint64_t ring_en:1;
+		uint64_t lnk_rst:1;
+		uint64_t arb:1;
+		uint64_t pkt_bp:4;
+		uint64_t host_mode:1;
+		uint64_t chip_rev:8;
+#else
+		uint64_t chip_rev:8;
+		uint64_t host_mode:1;
+		uint64_t pkt_bp:4;
+		uint64_t arb:1;
+		uint64_t lnk_rst:1;
+		uint64_t ring_en:1;
+		uint64_t cfg_rtry:16;
+		uint64_t p0_ntags:6;
+		uint64_t p1_ntags:6;
+		uint64_t reserved_44_63:20;
+#endif
+	} s;
+	struct cvmx_npei_ctl_status_cn52xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_44_63:20;
+		uint64_t p1_ntags:6;
+		uint64_t p0_ntags:6;
+		uint64_t cfg_rtry:16;
+		uint64_t reserved_15_15:1;
+		uint64_t lnk_rst:1;
+		uint64_t arb:1;
+		uint64_t reserved_9_12:4;
+		uint64_t host_mode:1;
+		uint64_t chip_rev:8;
+#else
+		uint64_t chip_rev:8;
+		uint64_t host_mode:1;
+		uint64_t reserved_9_12:4;
+		uint64_t arb:1;
+		uint64_t lnk_rst:1;
+		uint64_t reserved_15_15:1;
+		uint64_t cfg_rtry:16;
+		uint64_t p0_ntags:6;
+		uint64_t p1_ntags:6;
+		uint64_t reserved_44_63:20;
+#endif
+	} cn52xxp1;
+	struct cvmx_npei_ctl_status_cn56xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_15_63:49;
+		uint64_t lnk_rst:1;
+		uint64_t arb:1;
+		uint64_t pkt_bp:4;
+		uint64_t host_mode:1;
+		uint64_t chip_rev:8;
+#else
+		uint64_t chip_rev:8;
+		uint64_t host_mode:1;
+		uint64_t pkt_bp:4;
+		uint64_t arb:1;
+		uint64_t lnk_rst:1;
+		uint64_t reserved_15_63:49;
+#endif
+	} cn56xxp1;
+};
+
+union cvmx_npei_ctl_status2 {
+	uint64_t u64;
+	struct cvmx_npei_ctl_status2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t mps:1;
+		uint64_t mrrs:3;
+		uint64_t c1_w_flt:1;
+		uint64_t c0_w_flt:1;
+		uint64_t c1_b1_s:3;
+		uint64_t c0_b1_s:3;
+		uint64_t c1_wi_d:1;
+		uint64_t c1_b0_d:1;
+		uint64_t c0_wi_d:1;
+		uint64_t c0_b0_d:1;
+#else
+		uint64_t c0_b0_d:1;
+		uint64_t c0_wi_d:1;
+		uint64_t c1_b0_d:1;
+		uint64_t c1_wi_d:1;
+		uint64_t c0_b1_s:3;
+		uint64_t c1_b1_s:3;
+		uint64_t c0_w_flt:1;
+		uint64_t c1_w_flt:1;
+		uint64_t mrrs:3;
+		uint64_t mps:1;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_npei_data_out_cnt {
+	uint64_t u64;
+	struct cvmx_npei_data_out_cnt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_44_63:20;
+		uint64_t p1_ucnt:16;
+		uint64_t p1_fcnt:6;
+		uint64_t p0_ucnt:16;
+		uint64_t p0_fcnt:6;
+#else
+		uint64_t p0_fcnt:6;
+		uint64_t p0_ucnt:16;
+		uint64_t p1_fcnt:6;
+		uint64_t p1_ucnt:16;
+		uint64_t reserved_44_63:20;
+#endif
+	} s;
+};
+
+union cvmx_npei_dbg_data {
+	uint64_t u64;
+	struct cvmx_npei_dbg_data_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_28_63:36;
+		uint64_t qlm0_rev_lanes:1;
+		uint64_t reserved_25_26:2;
+		uint64_t qlm1_spd:2;
+		uint64_t c_mul:5;
+		uint64_t dsel_ext:1;
+		uint64_t data:17;
+#else
+		uint64_t data:17;
+		uint64_t dsel_ext:1;
+		uint64_t c_mul:5;
+		uint64_t qlm1_spd:2;
+		uint64_t reserved_25_26:2;
+		uint64_t qlm0_rev_lanes:1;
+		uint64_t reserved_28_63:36;
+#endif
+	} s;
+	struct cvmx_npei_dbg_data_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t qlm0_link_width:1;
+		uint64_t qlm0_rev_lanes:1;
+		uint64_t qlm1_mode:2;
+		uint64_t qlm1_spd:2;
+		uint64_t c_mul:5;
+		uint64_t dsel_ext:1;
+		uint64_t data:17;
+#else
+		uint64_t data:17;
+		uint64_t dsel_ext:1;
+		uint64_t c_mul:5;
+		uint64_t qlm1_spd:2;
+		uint64_t qlm1_mode:2;
+		uint64_t qlm0_rev_lanes:1;
+		uint64_t qlm0_link_width:1;
+		uint64_t reserved_29_63:35;
+#endif
+	} cn52xx;
+	struct cvmx_npei_dbg_data_cn56xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t qlm2_rev_lanes:1;
+		uint64_t qlm0_rev_lanes:1;
+		uint64_t qlm3_spd:2;
+		uint64_t qlm1_spd:2;
+		uint64_t c_mul:5;
+		uint64_t dsel_ext:1;
+		uint64_t data:17;
+#else
+		uint64_t data:17;
+		uint64_t dsel_ext:1;
+		uint64_t c_mul:5;
+		uint64_t qlm1_spd:2;
+		uint64_t qlm3_spd:2;
+		uint64_t qlm0_rev_lanes:1;
+		uint64_t qlm2_rev_lanes:1;
+		uint64_t reserved_29_63:35;
+#endif
+	} cn56xx;
+};
+
+union cvmx_npei_dbg_select {
+	uint64_t u64;
+	struct cvmx_npei_dbg_select_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t dbg_sel:16;
+#else
+		uint64_t dbg_sel:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_npei_dmax_counts {
+	uint64_t u64;
+	struct cvmx_npei_dmax_counts_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_39_63:25;
+		uint64_t fcnt:7;
+		uint64_t dbell:32;
+#else
+		uint64_t dbell:32;
+		uint64_t fcnt:7;
+		uint64_t reserved_39_63:25;
+#endif
+	} s;
+};
+
+union cvmx_npei_dmax_dbell {
+	uint32_t u32;
+	struct cvmx_npei_dmax_dbell_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t reserved_16_31:16;
+		uint32_t dbell:16;
+#else
+		uint32_t dbell:16;
+		uint32_t reserved_16_31:16;
+#endif
+	} s;
+};
+
+union cvmx_npei_dmax_ibuff_saddr {
+	uint64_t u64;
+	struct cvmx_npei_dmax_ibuff_saddr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_37_63:27;
+		uint64_t idle:1;
+		uint64_t saddr:29;
+		uint64_t reserved_0_6:7;
+#else
+		uint64_t reserved_0_6:7;
+		uint64_t saddr:29;
+		uint64_t idle:1;
+		uint64_t reserved_37_63:27;
+#endif
+	} s;
+	struct cvmx_npei_dmax_ibuff_saddr_cn52xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_36_63:28;
+		uint64_t saddr:29;
+		uint64_t reserved_0_6:7;
+#else
+		uint64_t reserved_0_6:7;
+		uint64_t saddr:29;
+		uint64_t reserved_36_63:28;
+#endif
+	} cn52xxp1;
+};
+
+union cvmx_npei_dmax_naddr {
+	uint64_t u64;
+	struct cvmx_npei_dmax_naddr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_36_63:28;
+		uint64_t addr:36;
+#else
+		uint64_t addr:36;
+		uint64_t reserved_36_63:28;
+#endif
+	} s;
+};
+
+union cvmx_npei_dma0_int_level {
+	uint64_t u64;
+	struct cvmx_npei_dma0_int_level_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t time:32;
+		uint64_t cnt:32;
+#else
+		uint64_t cnt:32;
+		uint64_t time:32;
+#endif
+	} s;
+};
+
+union cvmx_npei_dma1_int_level {
+	uint64_t u64;
+	struct cvmx_npei_dma1_int_level_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t time:32;
+		uint64_t cnt:32;
+#else
+		uint64_t cnt:32;
+		uint64_t time:32;
+#endif
+	} s;
+};
+
+union cvmx_npei_dma_cnts {
+	uint64_t u64;
+	struct cvmx_npei_dma_cnts_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t dma1:32;
+		uint64_t dma0:32;
+#else
+		uint64_t dma0:32;
+		uint64_t dma1:32;
+#endif
+	} s;
+};
+
+union cvmx_npei_dma_control {
+	uint64_t u64;
+	struct cvmx_npei_dma_control_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_40_63:24;
+		uint64_t p_32b_m:1;
+		uint64_t dma4_enb:1;
+		uint64_t dma3_enb:1;
+		uint64_t dma2_enb:1;
+		uint64_t dma1_enb:1;
+		uint64_t dma0_enb:1;
+		uint64_t b0_lend:1;
+		uint64_t dwb_denb:1;
+		uint64_t dwb_ichk:9;
+		uint64_t fpa_que:3;
+		uint64_t o_add1:1;
+		uint64_t o_ro:1;
+		uint64_t o_ns:1;
+		uint64_t o_es:2;
+		uint64_t o_mode:1;
+		uint64_t csize:14;
+#else
+		uint64_t csize:14;
+		uint64_t o_mode:1;
+		uint64_t o_es:2;
+		uint64_t o_ns:1;
+		uint64_t o_ro:1;
+		uint64_t o_add1:1;
+		uint64_t fpa_que:3;
+		uint64_t dwb_ichk:9;
+		uint64_t dwb_denb:1;
+		uint64_t b0_lend:1;
+		uint64_t dma0_enb:1;
+		uint64_t dma1_enb:1;
+		uint64_t dma2_enb:1;
+		uint64_t dma3_enb:1;
+		uint64_t dma4_enb:1;
+		uint64_t p_32b_m:1;
+		uint64_t reserved_40_63:24;
+#endif
+	} s;
+	struct cvmx_npei_dma_control_cn52xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_38_63:26;
+		uint64_t dma3_enb:1;
+		uint64_t dma2_enb:1;
+		uint64_t dma1_enb:1;
+		uint64_t dma0_enb:1;
+		uint64_t b0_lend:1;
+		uint64_t dwb_denb:1;
+		uint64_t dwb_ichk:9;
+		uint64_t fpa_que:3;
+		uint64_t o_add1:1;
+		uint64_t o_ro:1;
+		uint64_t o_ns:1;
+		uint64_t o_es:2;
+		uint64_t o_mode:1;
+		uint64_t csize:14;
+#else
+		uint64_t csize:14;
+		uint64_t o_mode:1;
+		uint64_t o_es:2;
+		uint64_t o_ns:1;
+		uint64_t o_ro:1;
+		uint64_t o_add1:1;
+		uint64_t fpa_que:3;
+		uint64_t dwb_ichk:9;
+		uint64_t dwb_denb:1;
+		uint64_t b0_lend:1;
+		uint64_t dma0_enb:1;
+		uint64_t dma1_enb:1;
+		uint64_t dma2_enb:1;
+		uint64_t dma3_enb:1;
+		uint64_t reserved_38_63:26;
+#endif
+	} cn52xxp1;
+	struct cvmx_npei_dma_control_cn56xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_39_63:25;
+		uint64_t dma4_enb:1;
+		uint64_t dma3_enb:1;
+		uint64_t dma2_enb:1;
+		uint64_t dma1_enb:1;
+		uint64_t dma0_enb:1;
+		uint64_t b0_lend:1;
+		uint64_t dwb_denb:1;
+		uint64_t dwb_ichk:9;
+		uint64_t fpa_que:3;
+		uint64_t o_add1:1;
+		uint64_t o_ro:1;
+		uint64_t o_ns:1;
+		uint64_t o_es:2;
+		uint64_t o_mode:1;
+		uint64_t csize:14;
+#else
+		uint64_t csize:14;
+		uint64_t o_mode:1;
+		uint64_t o_es:2;
+		uint64_t o_ns:1;
+		uint64_t o_ro:1;
+		uint64_t o_add1:1;
+		uint64_t fpa_que:3;
+		uint64_t dwb_ichk:9;
+		uint64_t dwb_denb:1;
+		uint64_t b0_lend:1;
+		uint64_t dma0_enb:1;
+		uint64_t dma1_enb:1;
+		uint64_t dma2_enb:1;
+		uint64_t dma3_enb:1;
+		uint64_t dma4_enb:1;
+		uint64_t reserved_39_63:25;
+#endif
+	} cn56xxp1;
+};
+
+union cvmx_npei_dma_pcie_req_num {
+	uint64_t u64;
+	struct cvmx_npei_dma_pcie_req_num_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t dma_arb:1;
+		uint64_t reserved_53_62:10;
+		uint64_t pkt_cnt:5;
+		uint64_t reserved_45_47:3;
+		uint64_t dma4_cnt:5;
+		uint64_t reserved_37_39:3;
+		uint64_t dma3_cnt:5;
+		uint64_t reserved_29_31:3;
+		uint64_t dma2_cnt:5;
+		uint64_t reserved_21_23:3;
+		uint64_t dma1_cnt:5;
+		uint64_t reserved_13_15:3;
+		uint64_t dma0_cnt:5;
+		uint64_t reserved_5_7:3;
+		uint64_t dma_cnt:5;
+#else
+		uint64_t dma_cnt:5;
+		uint64_t reserved_5_7:3;
+		uint64_t dma0_cnt:5;
+		uint64_t reserved_13_15:3;
+		uint64_t dma1_cnt:5;
+		uint64_t reserved_21_23:3;
+		uint64_t dma2_cnt:5;
+		uint64_t reserved_29_31:3;
+		uint64_t dma3_cnt:5;
+		uint64_t reserved_37_39:3;
+		uint64_t dma4_cnt:5;
+		uint64_t reserved_45_47:3;
+		uint64_t pkt_cnt:5;
+		uint64_t reserved_53_62:10;
+		uint64_t dma_arb:1;
+#endif
+	} s;
+};
+
+union cvmx_npei_dma_state1 {
+	uint64_t u64;
+	struct cvmx_npei_dma_state1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_40_63:24;
+		uint64_t d4_dwe:8;
+		uint64_t d3_dwe:8;
+		uint64_t d2_dwe:8;
+		uint64_t d1_dwe:8;
+		uint64_t d0_dwe:8;
+#else
+		uint64_t d0_dwe:8;
+		uint64_t d1_dwe:8;
+		uint64_t d2_dwe:8;
+		uint64_t d3_dwe:8;
+		uint64_t d4_dwe:8;
+		uint64_t reserved_40_63:24;
+#endif
+	} s;
+};
+
+union cvmx_npei_dma_state1_p1 {
+	uint64_t u64;
+	struct cvmx_npei_dma_state1_p1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_60_63:4;
+		uint64_t d0_difst:7;
+		uint64_t d1_difst:7;
+		uint64_t d2_difst:7;
+		uint64_t d3_difst:7;
+		uint64_t d4_difst:7;
+		uint64_t d0_reqst:5;
+		uint64_t d1_reqst:5;
+		uint64_t d2_reqst:5;
+		uint64_t d3_reqst:5;
+		uint64_t d4_reqst:5;
+#else
+		uint64_t d4_reqst:5;
+		uint64_t d3_reqst:5;
+		uint64_t d2_reqst:5;
+		uint64_t d1_reqst:5;
+		uint64_t d0_reqst:5;
+		uint64_t d4_difst:7;
+		uint64_t d3_difst:7;
+		uint64_t d2_difst:7;
+		uint64_t d1_difst:7;
+		uint64_t d0_difst:7;
+		uint64_t reserved_60_63:4;
+#endif
+	} s;
+	struct cvmx_npei_dma_state1_p1_cn52xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_60_63:4;
+		uint64_t d0_difst:7;
+		uint64_t d1_difst:7;
+		uint64_t d2_difst:7;
+		uint64_t d3_difst:7;
+		uint64_t reserved_25_31:7;
+		uint64_t d0_reqst:5;
+		uint64_t d1_reqst:5;
+		uint64_t d2_reqst:5;
+		uint64_t d3_reqst:5;
+		uint64_t reserved_0_4:5;
+#else
+		uint64_t reserved_0_4:5;
+		uint64_t d3_reqst:5;
+		uint64_t d2_reqst:5;
+		uint64_t d1_reqst:5;
+		uint64_t d0_reqst:5;
+		uint64_t reserved_25_31:7;
+		uint64_t d3_difst:7;
+		uint64_t d2_difst:7;
+		uint64_t d1_difst:7;
+		uint64_t d0_difst:7;
+		uint64_t reserved_60_63:4;
+#endif
+	} cn52xxp1;
+};
+
+union cvmx_npei_dma_state2 {
+	uint64_t u64;
+	struct cvmx_npei_dma_state2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_28_63:36;
+		uint64_t ndwe:4;
+		uint64_t reserved_21_23:3;
+		uint64_t ndre:5;
+		uint64_t reserved_10_15:6;
+		uint64_t prd:10;
+#else
+		uint64_t prd:10;
+		uint64_t reserved_10_15:6;
+		uint64_t ndre:5;
+		uint64_t reserved_21_23:3;
+		uint64_t ndwe:4;
+		uint64_t reserved_28_63:36;
+#endif
+	} s;
+};
+
+union cvmx_npei_dma_state2_p1 {
+	uint64_t u64;
+	struct cvmx_npei_dma_state2_p1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_45_63:19;
+		uint64_t d0_dffst:9;
+		uint64_t d1_dffst:9;
+		uint64_t d2_dffst:9;
+		uint64_t d3_dffst:9;
+		uint64_t d4_dffst:9;
+#else
+		uint64_t d4_dffst:9;
+		uint64_t d3_dffst:9;
+		uint64_t d2_dffst:9;
+		uint64_t d1_dffst:9;
+		uint64_t d0_dffst:9;
+		uint64_t reserved_45_63:19;
+#endif
+	} s;
+	struct cvmx_npei_dma_state2_p1_cn52xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_45_63:19;
+		uint64_t d0_dffst:9;
+		uint64_t d1_dffst:9;
+		uint64_t d2_dffst:9;
+		uint64_t d3_dffst:9;
+		uint64_t reserved_0_8:9;
+#else
+		uint64_t reserved_0_8:9;
+		uint64_t d3_dffst:9;
+		uint64_t d2_dffst:9;
+		uint64_t d1_dffst:9;
+		uint64_t d0_dffst:9;
+		uint64_t reserved_45_63:19;
+#endif
+	} cn52xxp1;
+};
+
+union cvmx_npei_dma_state3_p1 {
+	uint64_t u64;
+	struct cvmx_npei_dma_state3_p1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_60_63:4;
+		uint64_t d0_drest:15;
+		uint64_t d1_drest:15;
+		uint64_t d2_drest:15;
+		uint64_t d3_drest:15;
+#else
+		uint64_t d3_drest:15;
+		uint64_t d2_drest:15;
+		uint64_t d1_drest:15;
+		uint64_t d0_drest:15;
+		uint64_t reserved_60_63:4;
+#endif
+	} s;
+};
+
+union cvmx_npei_dma_state4_p1 {
+	uint64_t u64;
+	struct cvmx_npei_dma_state4_p1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_52_63:12;
+		uint64_t d0_dwest:13;
+		uint64_t d1_dwest:13;
+		uint64_t d2_dwest:13;
+		uint64_t d3_dwest:13;
+#else
+		uint64_t d3_dwest:13;
+		uint64_t d2_dwest:13;
+		uint64_t d1_dwest:13;
+		uint64_t d0_dwest:13;
+		uint64_t reserved_52_63:12;
+#endif
+	} s;
+};
+
+union cvmx_npei_dma_state5_p1 {
+	uint64_t u64;
+	struct cvmx_npei_dma_state5_p1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_28_63:36;
+		uint64_t d4_drest:15;
+		uint64_t d4_dwest:13;
+#else
+		uint64_t d4_dwest:13;
+		uint64_t d4_drest:15;
+		uint64_t reserved_28_63:36;
+#endif
+	} s;
+};
+
+union cvmx_npei_int_a_enb {
+	uint64_t u64;
+	struct cvmx_npei_int_a_enb_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t pout_err:1;
+		uint64_t pin_bp:1;
+		uint64_t p1_rdlk:1;
+		uint64_t p0_rdlk:1;
+		uint64_t pgl_err:1;
+		uint64_t pdi_err:1;
+		uint64_t pop_err:1;
+		uint64_t pins_err:1;
+		uint64_t dma1_cpl:1;
+		uint64_t dma0_cpl:1;
+#else
+		uint64_t dma0_cpl:1;
+		uint64_t dma1_cpl:1;
+		uint64_t pins_err:1;
+		uint64_t pop_err:1;
+		uint64_t pdi_err:1;
+		uint64_t pgl_err:1;
+		uint64_t p0_rdlk:1;
+		uint64_t p1_rdlk:1;
+		uint64_t pin_bp:1;
+		uint64_t pout_err:1;
+		uint64_t reserved_10_63:54;
+#endif
+	} s;
+	struct cvmx_npei_int_a_enb_cn52xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t dma1_cpl:1;
+		uint64_t dma0_cpl:1;
+#else
+		uint64_t dma0_cpl:1;
+		uint64_t dma1_cpl:1;
+		uint64_t reserved_2_63:62;
+#endif
+	} cn52xxp1;
+};
+
+union cvmx_npei_int_a_enb2 {
+	uint64_t u64;
+	struct cvmx_npei_int_a_enb2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t pout_err:1;
+		uint64_t pin_bp:1;
+		uint64_t p1_rdlk:1;
+		uint64_t p0_rdlk:1;
+		uint64_t pgl_err:1;
+		uint64_t pdi_err:1;
+		uint64_t pop_err:1;
+		uint64_t pins_err:1;
+		uint64_t dma1_cpl:1;
+		uint64_t dma0_cpl:1;
+#else
+		uint64_t dma0_cpl:1;
+		uint64_t dma1_cpl:1;
+		uint64_t pins_err:1;
+		uint64_t pop_err:1;
+		uint64_t pdi_err:1;
+		uint64_t pgl_err:1;
+		uint64_t p0_rdlk:1;
+		uint64_t p1_rdlk:1;
+		uint64_t pin_bp:1;
+		uint64_t pout_err:1;
+		uint64_t reserved_10_63:54;
+#endif
+	} s;
+	struct cvmx_npei_int_a_enb2_cn52xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t dma1_cpl:1;
+		uint64_t dma0_cpl:1;
+#else
+		uint64_t dma0_cpl:1;
+		uint64_t dma1_cpl:1;
+		uint64_t reserved_2_63:62;
+#endif
+	} cn52xxp1;
+};
+
+union cvmx_npei_int_a_sum {
+	uint64_t u64;
+	struct cvmx_npei_int_a_sum_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t pout_err:1;
+		uint64_t pin_bp:1;
+		uint64_t p1_rdlk:1;
+		uint64_t p0_rdlk:1;
+		uint64_t pgl_err:1;
+		uint64_t pdi_err:1;
+		uint64_t pop_err:1;
+		uint64_t pins_err:1;
+		uint64_t dma1_cpl:1;
+		uint64_t dma0_cpl:1;
+#else
+		uint64_t dma0_cpl:1;
+		uint64_t dma1_cpl:1;
+		uint64_t pins_err:1;
+		uint64_t pop_err:1;
+		uint64_t pdi_err:1;
+		uint64_t pgl_err:1;
+		uint64_t p0_rdlk:1;
+		uint64_t p1_rdlk:1;
+		uint64_t pin_bp:1;
+		uint64_t pout_err:1;
+		uint64_t reserved_10_63:54;
+#endif
+	} s;
+	struct cvmx_npei_int_a_sum_cn52xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t dma1_cpl:1;
+		uint64_t dma0_cpl:1;
+#else
+		uint64_t dma0_cpl:1;
+		uint64_t dma1_cpl:1;
+		uint64_t reserved_2_63:62;
+#endif
+	} cn52xxp1;
+};
+
+union cvmx_npei_int_enb {
+	uint64_t u64;
+	struct cvmx_npei_int_enb_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t mio_inta:1;
+		uint64_t reserved_62_62:1;
+		uint64_t int_a:1;
+		uint64_t c1_ldwn:1;
+		uint64_t c0_ldwn:1;
+		uint64_t c1_exc:1;
+		uint64_t c0_exc:1;
+		uint64_t c1_up_wf:1;
+		uint64_t c0_up_wf:1;
+		uint64_t c1_un_wf:1;
+		uint64_t c0_un_wf:1;
+		uint64_t c1_un_bx:1;
+		uint64_t c1_un_wi:1;
+		uint64_t c1_un_b2:1;
+		uint64_t c1_un_b1:1;
+		uint64_t c1_un_b0:1;
+		uint64_t c1_up_bx:1;
+		uint64_t c1_up_wi:1;
+		uint64_t c1_up_b2:1;
+		uint64_t c1_up_b1:1;
+		uint64_t c1_up_b0:1;
+		uint64_t c0_un_bx:1;
+		uint64_t c0_un_wi:1;
+		uint64_t c0_un_b2:1;
+		uint64_t c0_un_b1:1;
+		uint64_t c0_un_b0:1;
+		uint64_t c0_up_bx:1;
+		uint64_t c0_up_wi:1;
+		uint64_t c0_up_b2:1;
+		uint64_t c0_up_b1:1;
+		uint64_t c0_up_b0:1;
+		uint64_t c1_hpint:1;
+		uint64_t c1_pmei:1;
+		uint64_t c1_wake:1;
+		uint64_t crs1_dr:1;
+		uint64_t c1_se:1;
+		uint64_t crs1_er:1;
+		uint64_t c1_aeri:1;
+		uint64_t c0_hpint:1;
+		uint64_t c0_pmei:1;
+		uint64_t c0_wake:1;
+		uint64_t crs0_dr:1;
+		uint64_t c0_se:1;
+		uint64_t crs0_er:1;
+		uint64_t c0_aeri:1;
+		uint64_t ptime:1;
+		uint64_t pcnt:1;
+		uint64_t pidbof:1;
+		uint64_t psldbof:1;
+		uint64_t dtime1:1;
+		uint64_t dtime0:1;
+		uint64_t dcnt1:1;
+		uint64_t dcnt0:1;
+		uint64_t dma1fi:1;
+		uint64_t dma0fi:1;
+		uint64_t dma4dbo:1;
+		uint64_t dma3dbo:1;
+		uint64_t dma2dbo:1;
+		uint64_t dma1dbo:1;
+		uint64_t dma0dbo:1;
+		uint64_t iob2big:1;
+		uint64_t bar0_to:1;
+		uint64_t rml_wto:1;
+		uint64_t rml_rto:1;
+#else
+		uint64_t rml_rto:1;
+		uint64_t rml_wto:1;
+		uint64_t bar0_to:1;
+		uint64_t iob2big:1;
+		uint64_t dma0dbo:1;
+		uint64_t dma1dbo:1;
+		uint64_t dma2dbo:1;
+		uint64_t dma3dbo:1;
+		uint64_t dma4dbo:1;
+		uint64_t dma0fi:1;
+		uint64_t dma1fi:1;
+		uint64_t dcnt0:1;
+		uint64_t dcnt1:1;
+		uint64_t dtime0:1;
+		uint64_t dtime1:1;
+		uint64_t psldbof:1;
+		uint64_t pidbof:1;
+		uint64_t pcnt:1;
+		uint64_t ptime:1;
+		uint64_t c0_aeri:1;
+		uint64_t crs0_er:1;
+		uint64_t c0_se:1;
+		uint64_t crs0_dr:1;
+		uint64_t c0_wake:1;
+		uint64_t c0_pmei:1;
+		uint64_t c0_hpint:1;
+		uint64_t c1_aeri:1;
+		uint64_t crs1_er:1;
+		uint64_t c1_se:1;
+		uint64_t crs1_dr:1;
+		uint64_t c1_wake:1;
+		uint64_t c1_pmei:1;
+		uint64_t c1_hpint:1;
+		uint64_t c0_up_b0:1;
+		uint64_t c0_up_b1:1;
+		uint64_t c0_up_b2:1;
+		uint64_t c0_up_wi:1;
+		uint64_t c0_up_bx:1;
+		uint64_t c0_un_b0:1;
+		uint64_t c0_un_b1:1;
+		uint64_t c0_un_b2:1;
+		uint64_t c0_un_wi:1;
+		uint64_t c0_un_bx:1;
+		uint64_t c1_up_b0:1;
+		uint64_t c1_up_b1:1;
+		uint64_t c1_up_b2:1;
+		uint64_t c1_up_wi:1;
+		uint64_t c1_up_bx:1;
+		uint64_t c1_un_b0:1;
+		uint64_t c1_un_b1:1;
+		uint64_t c1_un_b2:1;
+		uint64_t c1_un_wi:1;
+		uint64_t c1_un_bx:1;
+		uint64_t c0_un_wf:1;
+		uint64_t c1_un_wf:1;
+		uint64_t c0_up_wf:1;
+		uint64_t c1_up_wf:1;
+		uint64_t c0_exc:1;
+		uint64_t c1_exc:1;
+		uint64_t c0_ldwn:1;
+		uint64_t c1_ldwn:1;
+		uint64_t int_a:1;
+		uint64_t reserved_62_62:1;
+		uint64_t mio_inta:1;
+#endif
+	} s;
+	struct cvmx_npei_int_enb_cn52xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t mio_inta:1;
+		uint64_t reserved_62_62:1;
+		uint64_t int_a:1;
+		uint64_t c1_ldwn:1;
+		uint64_t c0_ldwn:1;
+		uint64_t c1_exc:1;
+		uint64_t c0_exc:1;
+		uint64_t c1_up_wf:1;
+		uint64_t c0_up_wf:1;
+		uint64_t c1_un_wf:1;
+		uint64_t c0_un_wf:1;
+		uint64_t c1_un_bx:1;
+		uint64_t c1_un_wi:1;
+		uint64_t c1_un_b2:1;
+		uint64_t c1_un_b1:1;
+		uint64_t c1_un_b0:1;
+		uint64_t c1_up_bx:1;
+		uint64_t c1_up_wi:1;
+		uint64_t c1_up_b2:1;
+		uint64_t c1_up_b1:1;
+		uint64_t c1_up_b0:1;
+		uint64_t c0_un_bx:1;
+		uint64_t c0_un_wi:1;
+		uint64_t c0_un_b2:1;
+		uint64_t c0_un_b1:1;
+		uint64_t c0_un_b0:1;
+		uint64_t c0_up_bx:1;
+		uint64_t c0_up_wi:1;
+		uint64_t c0_up_b2:1;
+		uint64_t c0_up_b1:1;
+		uint64_t c0_up_b0:1;
+		uint64_t c1_hpint:1;
+		uint64_t c1_pmei:1;
+		uint64_t c1_wake:1;
+		uint64_t crs1_dr:1;
+		uint64_t c1_se:1;
+		uint64_t crs1_er:1;
+		uint64_t c1_aeri:1;
+		uint64_t c0_hpint:1;
+		uint64_t c0_pmei:1;
+		uint64_t c0_wake:1;
+		uint64_t crs0_dr:1;
+		uint64_t c0_se:1;
+		uint64_t crs0_er:1;
+		uint64_t c0_aeri:1;
+		uint64_t ptime:1;
+		uint64_t pcnt:1;
+		uint64_t pidbof:1;
+		uint64_t psldbof:1;
+		uint64_t dtime1:1;
+		uint64_t dtime0:1;
+		uint64_t dcnt1:1;
+		uint64_t dcnt0:1;
+		uint64_t dma1fi:1;
+		uint64_t dma0fi:1;
+		uint64_t reserved_8_8:1;
+		uint64_t dma3dbo:1;
+		uint64_t dma2dbo:1;
+		uint64_t dma1dbo:1;
+		uint64_t dma0dbo:1;
+		uint64_t iob2big:1;
+		uint64_t bar0_to:1;
+		uint64_t rml_wto:1;
+		uint64_t rml_rto:1;
+#else
+		uint64_t rml_rto:1;
+		uint64_t rml_wto:1;
+		uint64_t bar0_to:1;
+		uint64_t iob2big:1;
+		uint64_t dma0dbo:1;
+		uint64_t dma1dbo:1;
+		uint64_t dma2dbo:1;
+		uint64_t dma3dbo:1;
+		uint64_t reserved_8_8:1;
+		uint64_t dma0fi:1;
+		uint64_t dma1fi:1;
+		uint64_t dcnt0:1;
+		uint64_t dcnt1:1;
+		uint64_t dtime0:1;
+		uint64_t dtime1:1;
+		uint64_t psldbof:1;
+		uint64_t pidbof:1;
+		uint64_t pcnt:1;
+		uint64_t ptime:1;
+		uint64_t c0_aeri:1;
+		uint64_t crs0_er:1;
+		uint64_t c0_se:1;
+		uint64_t crs0_dr:1;
+		uint64_t c0_wake:1;
+		uint64_t c0_pmei:1;
+		uint64_t c0_hpint:1;
+		uint64_t c1_aeri:1;
+		uint64_t crs1_er:1;
+		uint64_t c1_se:1;
+		uint64_t crs1_dr:1;
+		uint64_t c1_wake:1;
+		uint64_t c1_pmei:1;
+		uint64_t c1_hpint:1;
+		uint64_t c0_up_b0:1;
+		uint64_t c0_up_b1:1;
+		uint64_t c0_up_b2:1;
+		uint64_t c0_up_wi:1;
+		uint64_t c0_up_bx:1;
+		uint64_t c0_un_b0:1;
+		uint64_t c0_un_b1:1;
+		uint64_t c0_un_b2:1;
+		uint64_t c0_un_wi:1;
+		uint64_t c0_un_bx:1;
+		uint64_t c1_up_b0:1;
+		uint64_t c1_up_b1:1;
+		uint64_t c1_up_b2:1;
+		uint64_t c1_up_wi:1;
+		uint64_t c1_up_bx:1;
+		uint64_t c1_un_b0:1;
+		uint64_t c1_un_b1:1;
+		uint64_t c1_un_b2:1;
+		uint64_t c1_un_wi:1;
+		uint64_t c1_un_bx:1;
+		uint64_t c0_un_wf:1;
+		uint64_t c1_un_wf:1;
+		uint64_t c0_up_wf:1;
+		uint64_t c1_up_wf:1;
+		uint64_t c0_exc:1;
+		uint64_t c1_exc:1;
+		uint64_t c0_ldwn:1;
+		uint64_t c1_ldwn:1;
+		uint64_t int_a:1;
+		uint64_t reserved_62_62:1;
+		uint64_t mio_inta:1;
+#endif
+	} cn52xxp1;
+	struct cvmx_npei_int_enb_cn56xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t mio_inta:1;
+		uint64_t reserved_61_62:2;
+		uint64_t c1_ldwn:1;
+		uint64_t c0_ldwn:1;
+		uint64_t c1_exc:1;
+		uint64_t c0_exc:1;
+		uint64_t c1_up_wf:1;
+		uint64_t c0_up_wf:1;
+		uint64_t c1_un_wf:1;
+		uint64_t c0_un_wf:1;
+		uint64_t c1_un_bx:1;
+		uint64_t c1_un_wi:1;
+		uint64_t c1_un_b2:1;
+		uint64_t c1_un_b1:1;
+		uint64_t c1_un_b0:1;
+		uint64_t c1_up_bx:1;
+		uint64_t c1_up_wi:1;
+		uint64_t c1_up_b2:1;
+		uint64_t c1_up_b1:1;
+		uint64_t c1_up_b0:1;
+		uint64_t c0_un_bx:1;
+		uint64_t c0_un_wi:1;
+		uint64_t c0_un_b2:1;
+		uint64_t c0_un_b1:1;
+		uint64_t c0_un_b0:1;
+		uint64_t c0_up_bx:1;
+		uint64_t c0_up_wi:1;
+		uint64_t c0_up_b2:1;
+		uint64_t c0_up_b1:1;
+		uint64_t c0_up_b0:1;
+		uint64_t c1_hpint:1;
+		uint64_t c1_pmei:1;
+		uint64_t c1_wake:1;
+		uint64_t reserved_29_29:1;
+		uint64_t c1_se:1;
+		uint64_t reserved_27_27:1;
+		uint64_t c1_aeri:1;
+		uint64_t c0_hpint:1;
+		uint64_t c0_pmei:1;
+		uint64_t c0_wake:1;
+		uint64_t reserved_22_22:1;
+		uint64_t c0_se:1;
+		uint64_t reserved_20_20:1;
+		uint64_t c0_aeri:1;
+		uint64_t ptime:1;
+		uint64_t pcnt:1;
+		uint64_t pidbof:1;
+		uint64_t psldbof:1;
+		uint64_t dtime1:1;
+		uint64_t dtime0:1;
+		uint64_t dcnt1:1;
+		uint64_t dcnt0:1;
+		uint64_t dma1fi:1;
+		uint64_t dma0fi:1;
+		uint64_t dma4dbo:1;
+		uint64_t dma3dbo:1;
+		uint64_t dma2dbo:1;
+		uint64_t dma1dbo:1;
+		uint64_t dma0dbo:1;
+		uint64_t iob2big:1;
+		uint64_t bar0_to:1;
+		uint64_t rml_wto:1;
+		uint64_t rml_rto:1;
+#else
+		uint64_t rml_rto:1;
+		uint64_t rml_wto:1;
+		uint64_t bar0_to:1;
+		uint64_t iob2big:1;
+		uint64_t dma0dbo:1;
+		uint64_t dma1dbo:1;
+		uint64_t dma2dbo:1;
+		uint64_t dma3dbo:1;
+		uint64_t dma4dbo:1;
+		uint64_t dma0fi:1;
+		uint64_t dma1fi:1;
+		uint64_t dcnt0:1;
+		uint64_t dcnt1:1;
+		uint64_t dtime0:1;
+		uint64_t dtime1:1;
+		uint64_t psldbof:1;
+		uint64_t pidbof:1;
+		uint64_t pcnt:1;
+		uint64_t ptime:1;
+		uint64_t c0_aeri:1;
+		uint64_t reserved_20_20:1;
+		uint64_t c0_se:1;
+		uint64_t reserved_22_22:1;
+		uint64_t c0_wake:1;
+		uint64_t c0_pmei:1;
+		uint64_t c0_hpint:1;
+		uint64_t c1_aeri:1;
+		uint64_t reserved_27_27:1;
+		uint64_t c1_se:1;
+		uint64_t reserved_29_29:1;
+		uint64_t c1_wake:1;
+		uint64_t c1_pmei:1;
+		uint64_t c1_hpint:1;
+		uint64_t c0_up_b0:1;
+		uint64_t c0_up_b1:1;
+		uint64_t c0_up_b2:1;
+		uint64_t c0_up_wi:1;
+		uint64_t c0_up_bx:1;
+		uint64_t c0_un_b0:1;
+		uint64_t c0_un_b1:1;
+		uint64_t c0_un_b2:1;
+		uint64_t c0_un_wi:1;
+		uint64_t c0_un_bx:1;
+		uint64_t c1_up_b0:1;
+		uint64_t c1_up_b1:1;
+		uint64_t c1_up_b2:1;
+		uint64_t c1_up_wi:1;
+		uint64_t c1_up_bx:1;
+		uint64_t c1_un_b0:1;
+		uint64_t c1_un_b1:1;
+		uint64_t c1_un_b2:1;
+		uint64_t c1_un_wi:1;
+		uint64_t c1_un_bx:1;
+		uint64_t c0_un_wf:1;
+		uint64_t c1_un_wf:1;
+		uint64_t c0_up_wf:1;
+		uint64_t c1_up_wf:1;
+		uint64_t c0_exc:1;
+		uint64_t c1_exc:1;
+		uint64_t c0_ldwn:1;
+		uint64_t c1_ldwn:1;
+		uint64_t reserved_61_62:2;
+		uint64_t mio_inta:1;
+#endif
+	} cn56xxp1;
+};
+
+union cvmx_npei_int_enb2 {
+	uint64_t u64;
+	struct cvmx_npei_int_enb2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_62_63:2;
+		uint64_t int_a:1;
+		uint64_t c1_ldwn:1;
+		uint64_t c0_ldwn:1;
+		uint64_t c1_exc:1;
+		uint64_t c0_exc:1;
+		uint64_t c1_up_wf:1;
+		uint64_t c0_up_wf:1;
+		uint64_t c1_un_wf:1;
+		uint64_t c0_un_wf:1;
+		uint64_t c1_un_bx:1;
+		uint64_t c1_un_wi:1;
+		uint64_t c1_un_b2:1;
+		uint64_t c1_un_b1:1;
+		uint64_t c1_un_b0:1;
+		uint64_t c1_up_bx:1;
+		uint64_t c1_up_wi:1;
+		uint64_t c1_up_b2:1;
+		uint64_t c1_up_b1:1;
+		uint64_t c1_up_b0:1;
+		uint64_t c0_un_bx:1;
+		uint64_t c0_un_wi:1;
+		uint64_t c0_un_b2:1;
+		uint64_t c0_un_b1:1;
+		uint64_t c0_un_b0:1;
+		uint64_t c0_up_bx:1;
+		uint64_t c0_up_wi:1;
+		uint64_t c0_up_b2:1;
+		uint64_t c0_up_b1:1;
+		uint64_t c0_up_b0:1;
+		uint64_t c1_hpint:1;
+		uint64_t c1_pmei:1;
+		uint64_t c1_wake:1;
+		uint64_t crs1_dr:1;
+		uint64_t c1_se:1;
+		uint64_t crs1_er:1;
+		uint64_t c1_aeri:1;
+		uint64_t c0_hpint:1;
+		uint64_t c0_pmei:1;
+		uint64_t c0_wake:1;
+		uint64_t crs0_dr:1;
+		uint64_t c0_se:1;
+		uint64_t crs0_er:1;
+		uint64_t c0_aeri:1;
+		uint64_t ptime:1;
+		uint64_t pcnt:1;
+		uint64_t pidbof:1;
+		uint64_t psldbof:1;
+		uint64_t dtime1:1;
+		uint64_t dtime0:1;
+		uint64_t dcnt1:1;
+		uint64_t dcnt0:1;
+		uint64_t dma1fi:1;
+		uint64_t dma0fi:1;
+		uint64_t dma4dbo:1;
+		uint64_t dma3dbo:1;
+		uint64_t dma2dbo:1;
+		uint64_t dma1dbo:1;
+		uint64_t dma0dbo:1;
+		uint64_t iob2big:1;
+		uint64_t bar0_to:1;
+		uint64_t rml_wto:1;
+		uint64_t rml_rto:1;
+#else
+		uint64_t rml_rto:1;
+		uint64_t rml_wto:1;
+		uint64_t bar0_to:1;
+		uint64_t iob2big:1;
+		uint64_t dma0dbo:1;
+		uint64_t dma1dbo:1;
+		uint64_t dma2dbo:1;
+		uint64_t dma3dbo:1;
+		uint64_t dma4dbo:1;
+		uint64_t dma0fi:1;
+		uint64_t dma1fi:1;
+		uint64_t dcnt0:1;
+		uint64_t dcnt1:1;
+		uint64_t dtime0:1;
+		uint64_t dtime1:1;
+		uint64_t psldbof:1;
+		uint64_t pidbof:1;
+		uint64_t pcnt:1;
+		uint64_t ptime:1;
+		uint64_t c0_aeri:1;
+		uint64_t crs0_er:1;
+		uint64_t c0_se:1;
+		uint64_t crs0_dr:1;
+		uint64_t c0_wake:1;
+		uint64_t c0_pmei:1;
+		uint64_t c0_hpint:1;
+		uint64_t c1_aeri:1;
+		uint64_t crs1_er:1;
+		uint64_t c1_se:1;
+		uint64_t crs1_dr:1;
+		uint64_t c1_wake:1;
+		uint64_t c1_pmei:1;
+		uint64_t c1_hpint:1;
+		uint64_t c0_up_b0:1;
+		uint64_t c0_up_b1:1;
+		uint64_t c0_up_b2:1;
+		uint64_t c0_up_wi:1;
+		uint64_t c0_up_bx:1;
+		uint64_t c0_un_b0:1;
+		uint64_t c0_un_b1:1;
+		uint64_t c0_un_b2:1;
+		uint64_t c0_un_wi:1;
+		uint64_t c0_un_bx:1;
+		uint64_t c1_up_b0:1;
+		uint64_t c1_up_b1:1;
+		uint64_t c1_up_b2:1;
+		uint64_t c1_up_wi:1;
+		uint64_t c1_up_bx:1;
+		uint64_t c1_un_b0:1;
+		uint64_t c1_un_b1:1;
+		uint64_t c1_un_b2:1;
+		uint64_t c1_un_wi:1;
+		uint64_t c1_un_bx:1;
+		uint64_t c0_un_wf:1;
+		uint64_t c1_un_wf:1;
+		uint64_t c0_up_wf:1;
+		uint64_t c1_up_wf:1;
+		uint64_t c0_exc:1;
+		uint64_t c1_exc:1;
+		uint64_t c0_ldwn:1;
+		uint64_t c1_ldwn:1;
+		uint64_t int_a:1;
+		uint64_t reserved_62_63:2;
+#endif
+	} s;
+	struct cvmx_npei_int_enb2_cn52xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_62_63:2;
+		uint64_t int_a:1;
+		uint64_t c1_ldwn:1;
+		uint64_t c0_ldwn:1;
+		uint64_t c1_exc:1;
+		uint64_t c0_exc:1;
+		uint64_t c1_up_wf:1;
+		uint64_t c0_up_wf:1;
+		uint64_t c1_un_wf:1;
+		uint64_t c0_un_wf:1;
+		uint64_t c1_un_bx:1;
+		uint64_t c1_un_wi:1;
+		uint64_t c1_un_b2:1;
+		uint64_t c1_un_b1:1;
+		uint64_t c1_un_b0:1;
+		uint64_t c1_up_bx:1;
+		uint64_t c1_up_wi:1;
+		uint64_t c1_up_b2:1;
+		uint64_t c1_up_b1:1;
+		uint64_t c1_up_b0:1;
+		uint64_t c0_un_bx:1;
+		uint64_t c0_un_wi:1;
+		uint64_t c0_un_b2:1;
+		uint64_t c0_un_b1:1;
+		uint64_t c0_un_b0:1;
+		uint64_t c0_up_bx:1;
+		uint64_t c0_up_wi:1;
+		uint64_t c0_up_b2:1;
+		uint64_t c0_up_b1:1;
+		uint64_t c0_up_b0:1;
+		uint64_t c1_hpint:1;
+		uint64_t c1_pmei:1;
+		uint64_t c1_wake:1;
+		uint64_t crs1_dr:1;
+		uint64_t c1_se:1;
+		uint64_t crs1_er:1;
+		uint64_t c1_aeri:1;
+		uint64_t c0_hpint:1;
+		uint64_t c0_pmei:1;
+		uint64_t c0_wake:1;
+		uint64_t crs0_dr:1;
+		uint64_t c0_se:1;
+		uint64_t crs0_er:1;
+		uint64_t c0_aeri:1;
+		uint64_t ptime:1;
+		uint64_t pcnt:1;
+		uint64_t pidbof:1;
+		uint64_t psldbof:1;
+		uint64_t dtime1:1;
+		uint64_t dtime0:1;
+		uint64_t dcnt1:1;
+		uint64_t dcnt0:1;
+		uint64_t dma1fi:1;
+		uint64_t dma0fi:1;
+		uint64_t reserved_8_8:1;
+		uint64_t dma3dbo:1;
+		uint64_t dma2dbo:1;
+		uint64_t dma1dbo:1;
+		uint64_t dma0dbo:1;
+		uint64_t iob2big:1;
+		uint64_t bar0_to:1;
+		uint64_t rml_wto:1;
+		uint64_t rml_rto:1;
+#else
+		uint64_t rml_rto:1;
+		uint64_t rml_wto:1;
+		uint64_t bar0_to:1;
+		uint64_t iob2big:1;
+		uint64_t dma0dbo:1;
+		uint64_t dma1dbo:1;
+		uint64_t dma2dbo:1;
+		uint64_t dma3dbo:1;
+		uint64_t reserved_8_8:1;
+		uint64_t dma0fi:1;
+		uint64_t dma1fi:1;
+		uint64_t dcnt0:1;
+		uint64_t dcnt1:1;
+		uint64_t dtime0:1;
+		uint64_t dtime1:1;
+		uint64_t psldbof:1;
+		uint64_t pidbof:1;
+		uint64_t pcnt:1;
+		uint64_t ptime:1;
+		uint64_t c0_aeri:1;
+		uint64_t crs0_er:1;
+		uint64_t c0_se:1;
+		uint64_t crs0_dr:1;
+		uint64_t c0_wake:1;
+		uint64_t c0_pmei:1;
+		uint64_t c0_hpint:1;
+		uint64_t c1_aeri:1;
+		uint64_t crs1_er:1;
+		uint64_t c1_se:1;
+		uint64_t crs1_dr:1;
+		uint64_t c1_wake:1;
+		uint64_t c1_pmei:1;
+		uint64_t c1_hpint:1;
+		uint64_t c0_up_b0:1;
+		uint64_t c0_up_b1:1;
+		uint64_t c0_up_b2:1;
+		uint64_t c0_up_wi:1;
+		uint64_t c0_up_bx:1;
+		uint64_t c0_un_b0:1;
+		uint64_t c0_un_b1:1;
+		uint64_t c0_un_b2:1;
+		uint64_t c0_un_wi:1;
+		uint64_t c0_un_bx:1;
+		uint64_t c1_up_b0:1;
+		uint64_t c1_up_b1:1;
+		uint64_t c1_up_b2:1;
+		uint64_t c1_up_wi:1;
+		uint64_t c1_up_bx:1;
+		uint64_t c1_un_b0:1;
+		uint64_t c1_un_b1:1;
+		uint64_t c1_un_b2:1;
+		uint64_t c1_un_wi:1;
+		uint64_t c1_un_bx:1;
+		uint64_t c0_un_wf:1;
+		uint64_t c1_un_wf:1;
+		uint64_t c0_up_wf:1;
+		uint64_t c1_up_wf:1;
+		uint64_t c0_exc:1;
+		uint64_t c1_exc:1;
+		uint64_t c0_ldwn:1;
+		uint64_t c1_ldwn:1;
+		uint64_t int_a:1;
+		uint64_t reserved_62_63:2;
+#endif
+	} cn52xxp1;
+	struct cvmx_npei_int_enb2_cn56xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_61_63:3;
+		uint64_t c1_ldwn:1;
+		uint64_t c0_ldwn:1;
+		uint64_t c1_exc:1;
+		uint64_t c0_exc:1;
+		uint64_t c1_up_wf:1;
+		uint64_t c0_up_wf:1;
+		uint64_t c1_un_wf:1;
+		uint64_t c0_un_wf:1;
+		uint64_t c1_un_bx:1;
+		uint64_t c1_un_wi:1;
+		uint64_t c1_un_b2:1;
+		uint64_t c1_un_b1:1;
+		uint64_t c1_un_b0:1;
+		uint64_t c1_up_bx:1;
+		uint64_t c1_up_wi:1;
+		uint64_t c1_up_b2:1;
+		uint64_t c1_up_b1:1;
+		uint64_t c1_up_b0:1;
+		uint64_t c0_un_bx:1;
+		uint64_t c0_un_wi:1;
+		uint64_t c0_un_b2:1;
+		uint64_t c0_un_b1:1;
+		uint64_t c0_un_b0:1;
+		uint64_t c0_up_bx:1;
+		uint64_t c0_up_wi:1;
+		uint64_t c0_up_b2:1;
+		uint64_t c0_up_b1:1;
+		uint64_t c0_up_b0:1;
+		uint64_t c1_hpint:1;
+		uint64_t c1_pmei:1;
+		uint64_t c1_wake:1;
+		uint64_t reserved_29_29:1;
+		uint64_t c1_se:1;
+		uint64_t reserved_27_27:1;
+		uint64_t c1_aeri:1;
+		uint64_t c0_hpint:1;
+		uint64_t c0_pmei:1;
+		uint64_t c0_wake:1;
+		uint64_t reserved_22_22:1;
+		uint64_t c0_se:1;
+		uint64_t reserved_20_20:1;
+		uint64_t c0_aeri:1;
+		uint64_t ptime:1;
+		uint64_t pcnt:1;
+		uint64_t pidbof:1;
+		uint64_t psldbof:1;
+		uint64_t dtime1:1;
+		uint64_t dtime0:1;
+		uint64_t dcnt1:1;
+		uint64_t dcnt0:1;
+		uint64_t dma1fi:1;
+		uint64_t dma0fi:1;
+		uint64_t dma4dbo:1;
+		uint64_t dma3dbo:1;
+		uint64_t dma2dbo:1;
+		uint64_t dma1dbo:1;
+		uint64_t dma0dbo:1;
+		uint64_t iob2big:1;
+		uint64_t bar0_to:1;
+		uint64_t rml_wto:1;
+		uint64_t rml_rto:1;
+#else
+		uint64_t rml_rto:1;
+		uint64_t rml_wto:1;
+		uint64_t bar0_to:1;
+		uint64_t iob2big:1;
+		uint64_t dma0dbo:1;
+		uint64_t dma1dbo:1;
+		uint64_t dma2dbo:1;
+		uint64_t dma3dbo:1;
+		uint64_t dma4dbo:1;
+		uint64_t dma0fi:1;
+		uint64_t dma1fi:1;
+		uint64_t dcnt0:1;
+		uint64_t dcnt1:1;
+		uint64_t dtime0:1;
+		uint64_t dtime1:1;
+		uint64_t psldbof:1;
+		uint64_t pidbof:1;
+		uint64_t pcnt:1;
+		uint64_t ptime:1;
+		uint64_t c0_aeri:1;
+		uint64_t reserved_20_20:1;
+		uint64_t c0_se:1;
+		uint64_t reserved_22_22:1;
+		uint64_t c0_wake:1;
+		uint64_t c0_pmei:1;
+		uint64_t c0_hpint:1;
+		uint64_t c1_aeri:1;
+		uint64_t reserved_27_27:1;
+		uint64_t c1_se:1;
+		uint64_t reserved_29_29:1;
+		uint64_t c1_wake:1;
+		uint64_t c1_pmei:1;
+		uint64_t c1_hpint:1;
+		uint64_t c0_up_b0:1;
+		uint64_t c0_up_b1:1;
+		uint64_t c0_up_b2:1;
+		uint64_t c0_up_wi:1;
+		uint64_t c0_up_bx:1;
+		uint64_t c0_un_b0:1;
+		uint64_t c0_un_b1:1;
+		uint64_t c0_un_b2:1;
+		uint64_t c0_un_wi:1;
+		uint64_t c0_un_bx:1;
+		uint64_t c1_up_b0:1;
+		uint64_t c1_up_b1:1;
+		uint64_t c1_up_b2:1;
+		uint64_t c1_up_wi:1;
+		uint64_t c1_up_bx:1;
+		uint64_t c1_un_b0:1;
+		uint64_t c1_un_b1:1;
+		uint64_t c1_un_b2:1;
+		uint64_t c1_un_wi:1;
+		uint64_t c1_un_bx:1;
+		uint64_t c0_un_wf:1;
+		uint64_t c1_un_wf:1;
+		uint64_t c0_up_wf:1;
+		uint64_t c1_up_wf:1;
+		uint64_t c0_exc:1;
+		uint64_t c1_exc:1;
+		uint64_t c0_ldwn:1;
+		uint64_t c1_ldwn:1;
+		uint64_t reserved_61_63:3;
+#endif
+	} cn56xxp1;
+};
+
+union cvmx_npei_int_info {
+	uint64_t u64;
+	struct cvmx_npei_int_info_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t pidbof:6;
+		uint64_t psldbof:6;
+#else
+		uint64_t psldbof:6;
+		uint64_t pidbof:6;
+		uint64_t reserved_12_63:52;
+#endif
+	} s;
+};
+
+union cvmx_npei_int_sum {
+	uint64_t u64;
+	struct cvmx_npei_int_sum_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t mio_inta:1;
+		uint64_t reserved_62_62:1;
+		uint64_t int_a:1;
+		uint64_t c1_ldwn:1;
+		uint64_t c0_ldwn:1;
+		uint64_t c1_exc:1;
+		uint64_t c0_exc:1;
+		uint64_t c1_up_wf:1;
+		uint64_t c0_up_wf:1;
+		uint64_t c1_un_wf:1;
+		uint64_t c0_un_wf:1;
+		uint64_t c1_un_bx:1;
+		uint64_t c1_un_wi:1;
+		uint64_t c1_un_b2:1;
+		uint64_t c1_un_b1:1;
+		uint64_t c1_un_b0:1;
+		uint64_t c1_up_bx:1;
+		uint64_t c1_up_wi:1;
+		uint64_t c1_up_b2:1;
+		uint64_t c1_up_b1:1;
+		uint64_t c1_up_b0:1;
+		uint64_t c0_un_bx:1;
+		uint64_t c0_un_wi:1;
+		uint64_t c0_un_b2:1;
+		uint64_t c0_un_b1:1;
+		uint64_t c0_un_b0:1;
+		uint64_t c0_up_bx:1;
+		uint64_t c0_up_wi:1;
+		uint64_t c0_up_b2:1;
+		uint64_t c0_up_b1:1;
+		uint64_t c0_up_b0:1;
+		uint64_t c1_hpint:1;
+		uint64_t c1_pmei:1;
+		uint64_t c1_wake:1;
+		uint64_t crs1_dr:1;
+		uint64_t c1_se:1;
+		uint64_t crs1_er:1;
+		uint64_t c1_aeri:1;
+		uint64_t c0_hpint:1;
+		uint64_t c0_pmei:1;
+		uint64_t c0_wake:1;
+		uint64_t crs0_dr:1;
+		uint64_t c0_se:1;
+		uint64_t crs0_er:1;
+		uint64_t c0_aeri:1;
+		uint64_t ptime:1;
+		uint64_t pcnt:1;
+		uint64_t pidbof:1;
+		uint64_t psldbof:1;
+		uint64_t dtime1:1;
+		uint64_t dtime0:1;
+		uint64_t dcnt1:1;
+		uint64_t dcnt0:1;
+		uint64_t dma1fi:1;
+		uint64_t dma0fi:1;
+		uint64_t dma4dbo:1;
+		uint64_t dma3dbo:1;
+		uint64_t dma2dbo:1;
+		uint64_t dma1dbo:1;
+		uint64_t dma0dbo:1;
+		uint64_t iob2big:1;
+		uint64_t bar0_to:1;
+		uint64_t rml_wto:1;
+		uint64_t rml_rto:1;
+#else
+		uint64_t rml_rto:1;
+		uint64_t rml_wto:1;
+		uint64_t bar0_to:1;
+		uint64_t iob2big:1;
+		uint64_t dma0dbo:1;
+		uint64_t dma1dbo:1;
+		uint64_t dma2dbo:1;
+		uint64_t dma3dbo:1;
+		uint64_t dma4dbo:1;
+		uint64_t dma0fi:1;
+		uint64_t dma1fi:1;
+		uint64_t dcnt0:1;
+		uint64_t dcnt1:1;
+		uint64_t dtime0:1;
+		uint64_t dtime1:1;
+		uint64_t psldbof:1;
+		uint64_t pidbof:1;
+		uint64_t pcnt:1;
+		uint64_t ptime:1;
+		uint64_t c0_aeri:1;
+		uint64_t crs0_er:1;
+		uint64_t c0_se:1;
+		uint64_t crs0_dr:1;
+		uint64_t c0_wake:1;
+		uint64_t c0_pmei:1;
+		uint64_t c0_hpint:1;
+		uint64_t c1_aeri:1;
+		uint64_t crs1_er:1;
+		uint64_t c1_se:1;
+		uint64_t crs1_dr:1;
+		uint64_t c1_wake:1;
+		uint64_t c1_pmei:1;
+		uint64_t c1_hpint:1;
+		uint64_t c0_up_b0:1;
+		uint64_t c0_up_b1:1;
+		uint64_t c0_up_b2:1;
+		uint64_t c0_up_wi:1;
+		uint64_t c0_up_bx:1;
+		uint64_t c0_un_b0:1;
+		uint64_t c0_un_b1:1;
+		uint64_t c0_un_b2:1;
+		uint64_t c0_un_wi:1;
+		uint64_t c0_un_bx:1;
+		uint64_t c1_up_b0:1;
+		uint64_t c1_up_b1:1;
+		uint64_t c1_up_b2:1;
+		uint64_t c1_up_wi:1;
+		uint64_t c1_up_bx:1;
+		uint64_t c1_un_b0:1;
+		uint64_t c1_un_b1:1;
+		uint64_t c1_un_b2:1;
+		uint64_t c1_un_wi:1;
+		uint64_t c1_un_bx:1;
+		uint64_t c0_un_wf:1;
+		uint64_t c1_un_wf:1;
+		uint64_t c0_up_wf:1;
+		uint64_t c1_up_wf:1;
+		uint64_t c0_exc:1;
+		uint64_t c1_exc:1;
+		uint64_t c0_ldwn:1;
+		uint64_t c1_ldwn:1;
+		uint64_t int_a:1;
+		uint64_t reserved_62_62:1;
+		uint64_t mio_inta:1;
+#endif
+	} s;
+	struct cvmx_npei_int_sum_cn52xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t mio_inta:1;
+		uint64_t reserved_62_62:1;
+		uint64_t int_a:1;
+		uint64_t c1_ldwn:1;
+		uint64_t c0_ldwn:1;
+		uint64_t c1_exc:1;
+		uint64_t c0_exc:1;
+		uint64_t c1_up_wf:1;
+		uint64_t c0_up_wf:1;
+		uint64_t c1_un_wf:1;
+		uint64_t c0_un_wf:1;
+		uint64_t c1_un_bx:1;
+		uint64_t c1_un_wi:1;
+		uint64_t c1_un_b2:1;
+		uint64_t c1_un_b1:1;
+		uint64_t c1_un_b0:1;
+		uint64_t c1_up_bx:1;
+		uint64_t c1_up_wi:1;
+		uint64_t c1_up_b2:1;
+		uint64_t c1_up_b1:1;
+		uint64_t c1_up_b0:1;
+		uint64_t c0_un_bx:1;
+		uint64_t c0_un_wi:1;
+		uint64_t c0_un_b2:1;
+		uint64_t c0_un_b1:1;
+		uint64_t c0_un_b0:1;
+		uint64_t c0_up_bx:1;
+		uint64_t c0_up_wi:1;
+		uint64_t c0_up_b2:1;
+		uint64_t c0_up_b1:1;
+		uint64_t c0_up_b0:1;
+		uint64_t c1_hpint:1;
+		uint64_t c1_pmei:1;
+		uint64_t c1_wake:1;
+		uint64_t crs1_dr:1;
+		uint64_t c1_se:1;
+		uint64_t crs1_er:1;
+		uint64_t c1_aeri:1;
+		uint64_t c0_hpint:1;
+		uint64_t c0_pmei:1;
+		uint64_t c0_wake:1;
+		uint64_t crs0_dr:1;
+		uint64_t c0_se:1;
+		uint64_t crs0_er:1;
+		uint64_t c0_aeri:1;
+		uint64_t reserved_15_18:4;
+		uint64_t dtime1:1;
+		uint64_t dtime0:1;
+		uint64_t dcnt1:1;
+		uint64_t dcnt0:1;
+		uint64_t dma1fi:1;
+		uint64_t dma0fi:1;
+		uint64_t reserved_8_8:1;
+		uint64_t dma3dbo:1;
+		uint64_t dma2dbo:1;
+		uint64_t dma1dbo:1;
+		uint64_t dma0dbo:1;
+		uint64_t iob2big:1;
+		uint64_t bar0_to:1;
+		uint64_t rml_wto:1;
+		uint64_t rml_rto:1;
+#else
+		uint64_t rml_rto:1;
+		uint64_t rml_wto:1;
+		uint64_t bar0_to:1;
+		uint64_t iob2big:1;
+		uint64_t dma0dbo:1;
+		uint64_t dma1dbo:1;
+		uint64_t dma2dbo:1;
+		uint64_t dma3dbo:1;
+		uint64_t reserved_8_8:1;
+		uint64_t dma0fi:1;
+		uint64_t dma1fi:1;
+		uint64_t dcnt0:1;
+		uint64_t dcnt1:1;
+		uint64_t dtime0:1;
+		uint64_t dtime1:1;
+		uint64_t reserved_15_18:4;
+		uint64_t c0_aeri:1;
+		uint64_t crs0_er:1;
+		uint64_t c0_se:1;
+		uint64_t crs0_dr:1;
+		uint64_t c0_wake:1;
+		uint64_t c0_pmei:1;
+		uint64_t c0_hpint:1;
+		uint64_t c1_aeri:1;
+		uint64_t crs1_er:1;
+		uint64_t c1_se:1;
+		uint64_t crs1_dr:1;
+		uint64_t c1_wake:1;
+		uint64_t c1_pmei:1;
+		uint64_t c1_hpint:1;
+		uint64_t c0_up_b0:1;
+		uint64_t c0_up_b1:1;
+		uint64_t c0_up_b2:1;
+		uint64_t c0_up_wi:1;
+		uint64_t c0_up_bx:1;
+		uint64_t c0_un_b0:1;
+		uint64_t c0_un_b1:1;
+		uint64_t c0_un_b2:1;
+		uint64_t c0_un_wi:1;
+		uint64_t c0_un_bx:1;
+		uint64_t c1_up_b0:1;
+		uint64_t c1_up_b1:1;
+		uint64_t c1_up_b2:1;
+		uint64_t c1_up_wi:1;
+		uint64_t c1_up_bx:1;
+		uint64_t c1_un_b0:1;
+		uint64_t c1_un_b1:1;
+		uint64_t c1_un_b2:1;
+		uint64_t c1_un_wi:1;
+		uint64_t c1_un_bx:1;
+		uint64_t c0_un_wf:1;
+		uint64_t c1_un_wf:1;
+		uint64_t c0_up_wf:1;
+		uint64_t c1_up_wf:1;
+		uint64_t c0_exc:1;
+		uint64_t c1_exc:1;
+		uint64_t c0_ldwn:1;
+		uint64_t c1_ldwn:1;
+		uint64_t int_a:1;
+		uint64_t reserved_62_62:1;
+		uint64_t mio_inta:1;
+#endif
+	} cn52xxp1;
+	struct cvmx_npei_int_sum_cn56xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t mio_inta:1;
+		uint64_t reserved_61_62:2;
+		uint64_t c1_ldwn:1;
+		uint64_t c0_ldwn:1;
+		uint64_t c1_exc:1;
+		uint64_t c0_exc:1;
+		uint64_t c1_up_wf:1;
+		uint64_t c0_up_wf:1;
+		uint64_t c1_un_wf:1;
+		uint64_t c0_un_wf:1;
+		uint64_t c1_un_bx:1;
+		uint64_t c1_un_wi:1;
+		uint64_t c1_un_b2:1;
+		uint64_t c1_un_b1:1;
+		uint64_t c1_un_b0:1;
+		uint64_t c1_up_bx:1;
+		uint64_t c1_up_wi:1;
+		uint64_t c1_up_b2:1;
+		uint64_t c1_up_b1:1;
+		uint64_t c1_up_b0:1;
+		uint64_t c0_un_bx:1;
+		uint64_t c0_un_wi:1;
+		uint64_t c0_un_b2:1;
+		uint64_t c0_un_b1:1;
+		uint64_t c0_un_b0:1;
+		uint64_t c0_up_bx:1;
+		uint64_t c0_up_wi:1;
+		uint64_t c0_up_b2:1;
+		uint64_t c0_up_b1:1;
+		uint64_t c0_up_b0:1;
+		uint64_t c1_hpint:1;
+		uint64_t c1_pmei:1;
+		uint64_t c1_wake:1;
+		uint64_t reserved_29_29:1;
+		uint64_t c1_se:1;
+		uint64_t reserved_27_27:1;
+		uint64_t c1_aeri:1;
+		uint64_t c0_hpint:1;
+		uint64_t c0_pmei:1;
+		uint64_t c0_wake:1;
+		uint64_t reserved_22_22:1;
+		uint64_t c0_se:1;
+		uint64_t reserved_20_20:1;
+		uint64_t c0_aeri:1;
+		uint64_t reserved_15_18:4;
+		uint64_t dtime1:1;
+		uint64_t dtime0:1;
+		uint64_t dcnt1:1;
+		uint64_t dcnt0:1;
+		uint64_t dma1fi:1;
+		uint64_t dma0fi:1;
+		uint64_t dma4dbo:1;
+		uint64_t dma3dbo:1;
+		uint64_t dma2dbo:1;
+		uint64_t dma1dbo:1;
+		uint64_t dma0dbo:1;
+		uint64_t iob2big:1;
+		uint64_t bar0_to:1;
+		uint64_t rml_wto:1;
+		uint64_t rml_rto:1;
+#else
+		uint64_t rml_rto:1;
+		uint64_t rml_wto:1;
+		uint64_t bar0_to:1;
+		uint64_t iob2big:1;
+		uint64_t dma0dbo:1;
+		uint64_t dma1dbo:1;
+		uint64_t dma2dbo:1;
+		uint64_t dma3dbo:1;
+		uint64_t dma4dbo:1;
+		uint64_t dma0fi:1;
+		uint64_t dma1fi:1;
+		uint64_t dcnt0:1;
+		uint64_t dcnt1:1;
+		uint64_t dtime0:1;
+		uint64_t dtime1:1;
+		uint64_t reserved_15_18:4;
+		uint64_t c0_aeri:1;
+		uint64_t reserved_20_20:1;
+		uint64_t c0_se:1;
+		uint64_t reserved_22_22:1;
+		uint64_t c0_wake:1;
+		uint64_t c0_pmei:1;
+		uint64_t c0_hpint:1;
+		uint64_t c1_aeri:1;
+		uint64_t reserved_27_27:1;
+		uint64_t c1_se:1;
+		uint64_t reserved_29_29:1;
+		uint64_t c1_wake:1;
+		uint64_t c1_pmei:1;
+		uint64_t c1_hpint:1;
+		uint64_t c0_up_b0:1;
+		uint64_t c0_up_b1:1;
+		uint64_t c0_up_b2:1;
+		uint64_t c0_up_wi:1;
+		uint64_t c0_up_bx:1;
+		uint64_t c0_un_b0:1;
+		uint64_t c0_un_b1:1;
+		uint64_t c0_un_b2:1;
+		uint64_t c0_un_wi:1;
+		uint64_t c0_un_bx:1;
+		uint64_t c1_up_b0:1;
+		uint64_t c1_up_b1:1;
+		uint64_t c1_up_b2:1;
+		uint64_t c1_up_wi:1;
+		uint64_t c1_up_bx:1;
+		uint64_t c1_un_b0:1;
+		uint64_t c1_un_b1:1;
+		uint64_t c1_un_b2:1;
+		uint64_t c1_un_wi:1;
+		uint64_t c1_un_bx:1;
+		uint64_t c0_un_wf:1;
+		uint64_t c1_un_wf:1;
+		uint64_t c0_up_wf:1;
+		uint64_t c1_up_wf:1;
+		uint64_t c0_exc:1;
+		uint64_t c1_exc:1;
+		uint64_t c0_ldwn:1;
+		uint64_t c1_ldwn:1;
+		uint64_t reserved_61_62:2;
+		uint64_t mio_inta:1;
+#endif
+	} cn56xxp1;
+};
+
+union cvmx_npei_int_sum2 {
+	uint64_t u64;
+	struct cvmx_npei_int_sum2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t mio_inta:1;
+		uint64_t reserved_62_62:1;
+		uint64_t int_a:1;
+		uint64_t c1_ldwn:1;
+		uint64_t c0_ldwn:1;
+		uint64_t c1_exc:1;
+		uint64_t c0_exc:1;
+		uint64_t c1_up_wf:1;
+		uint64_t c0_up_wf:1;
+		uint64_t c1_un_wf:1;
+		uint64_t c0_un_wf:1;
+		uint64_t c1_un_bx:1;
+		uint64_t c1_un_wi:1;
+		uint64_t c1_un_b2:1;
+		uint64_t c1_un_b1:1;
+		uint64_t c1_un_b0:1;
+		uint64_t c1_up_bx:1;
+		uint64_t c1_up_wi:1;
+		uint64_t c1_up_b2:1;
+		uint64_t c1_up_b1:1;
+		uint64_t c1_up_b0:1;
+		uint64_t c0_un_bx:1;
+		uint64_t c0_un_wi:1;
+		uint64_t c0_un_b2:1;
+		uint64_t c0_un_b1:1;
+		uint64_t c0_un_b0:1;
+		uint64_t c0_up_bx:1;
+		uint64_t c0_up_wi:1;
+		uint64_t c0_up_b2:1;
+		uint64_t c0_up_b1:1;
+		uint64_t c0_up_b0:1;
+		uint64_t c1_hpint:1;
+		uint64_t c1_pmei:1;
+		uint64_t c1_wake:1;
+		uint64_t crs1_dr:1;
+		uint64_t c1_se:1;
+		uint64_t crs1_er:1;
+		uint64_t c1_aeri:1;
+		uint64_t c0_hpint:1;
+		uint64_t c0_pmei:1;
+		uint64_t c0_wake:1;
+		uint64_t crs0_dr:1;
+		uint64_t c0_se:1;
+		uint64_t crs0_er:1;
+		uint64_t c0_aeri:1;
+		uint64_t reserved_15_18:4;
+		uint64_t dtime1:1;
+		uint64_t dtime0:1;
+		uint64_t dcnt1:1;
+		uint64_t dcnt0:1;
+		uint64_t dma1fi:1;
+		uint64_t dma0fi:1;
+		uint64_t reserved_8_8:1;
+		uint64_t dma3dbo:1;
+		uint64_t dma2dbo:1;
+		uint64_t dma1dbo:1;
+		uint64_t dma0dbo:1;
+		uint64_t iob2big:1;
+		uint64_t bar0_to:1;
+		uint64_t rml_wto:1;
+		uint64_t rml_rto:1;
+#else
+		uint64_t rml_rto:1;
+		uint64_t rml_wto:1;
+		uint64_t bar0_to:1;
+		uint64_t iob2big:1;
+		uint64_t dma0dbo:1;
+		uint64_t dma1dbo:1;
+		uint64_t dma2dbo:1;
+		uint64_t dma3dbo:1;
+		uint64_t reserved_8_8:1;
+		uint64_t dma0fi:1;
+		uint64_t dma1fi:1;
+		uint64_t dcnt0:1;
+		uint64_t dcnt1:1;
+		uint64_t dtime0:1;
+		uint64_t dtime1:1;
+		uint64_t reserved_15_18:4;
+		uint64_t c0_aeri:1;
+		uint64_t crs0_er:1;
+		uint64_t c0_se:1;
+		uint64_t crs0_dr:1;
+		uint64_t c0_wake:1;
+		uint64_t c0_pmei:1;
+		uint64_t c0_hpint:1;
+		uint64_t c1_aeri:1;
+		uint64_t crs1_er:1;
+		uint64_t c1_se:1;
+		uint64_t crs1_dr:1;
+		uint64_t c1_wake:1;
+		uint64_t c1_pmei:1;
+		uint64_t c1_hpint:1;
+		uint64_t c0_up_b0:1;
+		uint64_t c0_up_b1:1;
+		uint64_t c0_up_b2:1;
+		uint64_t c0_up_wi:1;
+		uint64_t c0_up_bx:1;
+		uint64_t c0_un_b0:1;
+		uint64_t c0_un_b1:1;
+		uint64_t c0_un_b2:1;
+		uint64_t c0_un_wi:1;
+		uint64_t c0_un_bx:1;
+		uint64_t c1_up_b0:1;
+		uint64_t c1_up_b1:1;
+		uint64_t c1_up_b2:1;
+		uint64_t c1_up_wi:1;
+		uint64_t c1_up_bx:1;
+		uint64_t c1_un_b0:1;
+		uint64_t c1_un_b1:1;
+		uint64_t c1_un_b2:1;
+		uint64_t c1_un_wi:1;
+		uint64_t c1_un_bx:1;
+		uint64_t c0_un_wf:1;
+		uint64_t c1_un_wf:1;
+		uint64_t c0_up_wf:1;
+		uint64_t c1_up_wf:1;
+		uint64_t c0_exc:1;
+		uint64_t c1_exc:1;
+		uint64_t c0_ldwn:1;
+		uint64_t c1_ldwn:1;
+		uint64_t int_a:1;
+		uint64_t reserved_62_62:1;
+		uint64_t mio_inta:1;
+#endif
+	} s;
+};
+
+union cvmx_npei_last_win_rdata0 {
+	uint64_t u64;
+	struct cvmx_npei_last_win_rdata0_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t data:64;
+#else
+		uint64_t data:64;
+#endif
+	} s;
+};
+
+union cvmx_npei_last_win_rdata1 {
+	uint64_t u64;
+	struct cvmx_npei_last_win_rdata1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t data:64;
+#else
+		uint64_t data:64;
+#endif
+	} s;
+};
+
+union cvmx_npei_mem_access_ctl {
+	uint64_t u64;
+	struct cvmx_npei_mem_access_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_14_63:50;
+		uint64_t max_word:4;
+		uint64_t timer:10;
+#else
+		uint64_t timer:10;
+		uint64_t max_word:4;
+		uint64_t reserved_14_63:50;
+#endif
+	} s;
+};
+
+union cvmx_npei_mem_access_subidx {
+	uint64_t u64;
+	struct cvmx_npei_mem_access_subidx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_42_63:22;
+		uint64_t zero:1;
+		uint64_t port:2;
+		uint64_t nmerge:1;
+		uint64_t esr:2;
+		uint64_t esw:2;
+		uint64_t nsr:1;
+		uint64_t nsw:1;
+		uint64_t ror:1;
+		uint64_t row:1;
+		uint64_t ba:30;
+#else
+		uint64_t ba:30;
+		uint64_t row:1;
+		uint64_t ror:1;
+		uint64_t nsw:1;
+		uint64_t nsr:1;
+		uint64_t esw:2;
+		uint64_t esr:2;
+		uint64_t nmerge:1;
+		uint64_t port:2;
+		uint64_t zero:1;
+		uint64_t reserved_42_63:22;
+#endif
+	} s;
+};
+
+union cvmx_npei_msi_enb0 {
+	uint64_t u64;
+	struct cvmx_npei_msi_enb0_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t enb:64;
+#else
+		uint64_t enb:64;
+#endif
+	} s;
+};
+
+union cvmx_npei_msi_enb1 {
+	uint64_t u64;
+	struct cvmx_npei_msi_enb1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t enb:64;
+#else
+		uint64_t enb:64;
+#endif
+	} s;
+};
+
+union cvmx_npei_msi_enb2 {
+	uint64_t u64;
+	struct cvmx_npei_msi_enb2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t enb:64;
+#else
+		uint64_t enb:64;
+#endif
+	} s;
+};
+
+union cvmx_npei_msi_enb3 {
+	uint64_t u64;
+	struct cvmx_npei_msi_enb3_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t enb:64;
+#else
+		uint64_t enb:64;
+#endif
+	} s;
+};
+
+union cvmx_npei_msi_rcv0 {
+	uint64_t u64;
+	struct cvmx_npei_msi_rcv0_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t intr:64;
+#else
+		uint64_t intr:64;
+#endif
+	} s;
+};
+
+union cvmx_npei_msi_rcv1 {
+	uint64_t u64;
+	struct cvmx_npei_msi_rcv1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t intr:64;
+#else
+		uint64_t intr:64;
+#endif
+	} s;
+};
+
+union cvmx_npei_msi_rcv2 {
+	uint64_t u64;
+	struct cvmx_npei_msi_rcv2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t intr:64;
+#else
+		uint64_t intr:64;
+#endif
+	} s;
+};
+
+union cvmx_npei_msi_rcv3 {
+	uint64_t u64;
+	struct cvmx_npei_msi_rcv3_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t intr:64;
+#else
+		uint64_t intr:64;
+#endif
+	} s;
+};
+
+union cvmx_npei_msi_rd_map {
+	uint64_t u64;
+	struct cvmx_npei_msi_rd_map_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t rd_int:8;
+		uint64_t msi_int:8;
+#else
+		uint64_t msi_int:8;
+		uint64_t rd_int:8;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_npei_msi_w1c_enb0 {
+	uint64_t u64;
+	struct cvmx_npei_msi_w1c_enb0_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t clr:64;
+#else
+		uint64_t clr:64;
+#endif
+	} s;
+};
+
+union cvmx_npei_msi_w1c_enb1 {
+	uint64_t u64;
+	struct cvmx_npei_msi_w1c_enb1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t clr:64;
+#else
+		uint64_t clr:64;
+#endif
+	} s;
+};
+
+union cvmx_npei_msi_w1c_enb2 {
+	uint64_t u64;
+	struct cvmx_npei_msi_w1c_enb2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t clr:64;
+#else
+		uint64_t clr:64;
+#endif
+	} s;
+};
+
+union cvmx_npei_msi_w1c_enb3 {
+	uint64_t u64;
+	struct cvmx_npei_msi_w1c_enb3_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t clr:64;
+#else
+		uint64_t clr:64;
+#endif
+	} s;
+};
+
+union cvmx_npei_msi_w1s_enb0 {
+	uint64_t u64;
+	struct cvmx_npei_msi_w1s_enb0_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t set:64;
+#else
+		uint64_t set:64;
+#endif
+	} s;
+};
+
+union cvmx_npei_msi_w1s_enb1 {
+	uint64_t u64;
+	struct cvmx_npei_msi_w1s_enb1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t set:64;
+#else
+		uint64_t set:64;
+#endif
+	} s;
+};
+
+union cvmx_npei_msi_w1s_enb2 {
+	uint64_t u64;
+	struct cvmx_npei_msi_w1s_enb2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t set:64;
+#else
+		uint64_t set:64;
+#endif
+	} s;
+};
+
+union cvmx_npei_msi_w1s_enb3 {
+	uint64_t u64;
+	struct cvmx_npei_msi_w1s_enb3_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t set:64;
+#else
+		uint64_t set:64;
+#endif
+	} s;
+};
+
+union cvmx_npei_msi_wr_map {
+	uint64_t u64;
+	struct cvmx_npei_msi_wr_map_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t ciu_int:8;
+		uint64_t msi_int:8;
+#else
+		uint64_t msi_int:8;
+		uint64_t ciu_int:8;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_npei_pcie_credit_cnt {
+	uint64_t u64;
+	struct cvmx_npei_pcie_credit_cnt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t p1_ccnt:8;
+		uint64_t p1_ncnt:8;
+		uint64_t p1_pcnt:8;
+		uint64_t p0_ccnt:8;
+		uint64_t p0_ncnt:8;
+		uint64_t p0_pcnt:8;
+#else
+		uint64_t p0_pcnt:8;
+		uint64_t p0_ncnt:8;
+		uint64_t p0_ccnt:8;
+		uint64_t p1_pcnt:8;
+		uint64_t p1_ncnt:8;
+		uint64_t p1_ccnt:8;
+		uint64_t reserved_48_63:16;
+#endif
+	} s;
+};
+
+union cvmx_npei_pcie_msi_rcv {
+	uint64_t u64;
+	struct cvmx_npei_pcie_msi_rcv_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t intr:8;
+#else
+		uint64_t intr:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_npei_pcie_msi_rcv_b1 {
+	uint64_t u64;
+	struct cvmx_npei_pcie_msi_rcv_b1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t intr:8;
+		uint64_t reserved_0_7:8;
+#else
+		uint64_t reserved_0_7:8;
+		uint64_t intr:8;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_npei_pcie_msi_rcv_b2 {
+	uint64_t u64;
+	struct cvmx_npei_pcie_msi_rcv_b2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_24_63:40;
+		uint64_t intr:8;
+		uint64_t reserved_0_15:16;
+#else
+		uint64_t reserved_0_15:16;
+		uint64_t intr:8;
+		uint64_t reserved_24_63:40;
+#endif
+	} s;
+};
+
+union cvmx_npei_pcie_msi_rcv_b3 {
+	uint64_t u64;
+	struct cvmx_npei_pcie_msi_rcv_b3_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t intr:8;
+		uint64_t reserved_0_23:24;
+#else
+		uint64_t reserved_0_23:24;
+		uint64_t intr:8;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_npei_pktx_cnts {
+	uint64_t u64;
+	struct cvmx_npei_pktx_cnts_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_54_63:10;
+		uint64_t timer:22;
+		uint64_t cnt:32;
+#else
+		uint64_t cnt:32;
+		uint64_t timer:22;
+		uint64_t reserved_54_63:10;
+#endif
+	} s;
+};
+
+union cvmx_npei_pktx_in_bp {
+	uint64_t u64;
+	struct cvmx_npei_pktx_in_bp_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t wmark:32;
+		uint64_t cnt:32;
+#else
+		uint64_t cnt:32;
+		uint64_t wmark:32;
+#endif
+	} s;
+};
+
+union cvmx_npei_pktx_instr_baddr {
+	uint64_t u64;
+	struct cvmx_npei_pktx_instr_baddr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t addr:61;
+		uint64_t reserved_0_2:3;
+#else
+		uint64_t reserved_0_2:3;
+		uint64_t addr:61;
+#endif
+	} s;
+};
+
+union cvmx_npei_pktx_instr_baoff_dbell {
+	uint64_t u64;
+	struct cvmx_npei_pktx_instr_baoff_dbell_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t aoff:32;
+		uint64_t dbell:32;
+#else
+		uint64_t dbell:32;
+		uint64_t aoff:32;
+#endif
+	} s;
+};
+
+union cvmx_npei_pktx_instr_fifo_rsize {
+	uint64_t u64;
+	struct cvmx_npei_pktx_instr_fifo_rsize_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t max:9;
+		uint64_t rrp:9;
+		uint64_t wrp:9;
+		uint64_t fcnt:5;
+		uint64_t rsize:32;
+#else
+		uint64_t rsize:32;
+		uint64_t fcnt:5;
+		uint64_t wrp:9;
+		uint64_t rrp:9;
+		uint64_t max:9;
+#endif
+	} s;
+};
+
+union cvmx_npei_pktx_instr_header {
+	uint64_t u64;
+	struct cvmx_npei_pktx_instr_header_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_44_63:20;
+		uint64_t pbp:1;
+		uint64_t reserved_38_42:5;
+		uint64_t rparmode:2;
+		uint64_t reserved_35_35:1;
+		uint64_t rskp_len:7;
+		uint64_t reserved_22_27:6;
+		uint64_t use_ihdr:1;
+		uint64_t reserved_16_20:5;
+		uint64_t par_mode:2;
+		uint64_t reserved_13_13:1;
+		uint64_t skp_len:7;
+		uint64_t reserved_0_5:6;
+#else
+		uint64_t reserved_0_5:6;
+		uint64_t skp_len:7;
+		uint64_t reserved_13_13:1;
+		uint64_t par_mode:2;
+		uint64_t reserved_16_20:5;
+		uint64_t use_ihdr:1;
+		uint64_t reserved_22_27:6;
+		uint64_t rskp_len:7;
+		uint64_t reserved_35_35:1;
+		uint64_t rparmode:2;
+		uint64_t reserved_38_42:5;
+		uint64_t pbp:1;
+		uint64_t reserved_44_63:20;
+#endif
+	} s;
+};
+
+union cvmx_npei_pktx_slist_baddr {
+	uint64_t u64;
+	struct cvmx_npei_pktx_slist_baddr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t addr:60;
+		uint64_t reserved_0_3:4;
+#else
+		uint64_t reserved_0_3:4;
+		uint64_t addr:60;
+#endif
+	} s;
+};
+
+union cvmx_npei_pktx_slist_baoff_dbell {
+	uint64_t u64;
+	struct cvmx_npei_pktx_slist_baoff_dbell_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t aoff:32;
+		uint64_t dbell:32;
+#else
+		uint64_t dbell:32;
+		uint64_t aoff:32;
+#endif
+	} s;
+};
+
+union cvmx_npei_pktx_slist_fifo_rsize {
+	uint64_t u64;
+	struct cvmx_npei_pktx_slist_fifo_rsize_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t rsize:32;
+#else
+		uint64_t rsize:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_npei_pkt_cnt_int {
+	uint64_t u64;
+	struct cvmx_npei_pkt_cnt_int_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t port:32;
+#else
+		uint64_t port:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_npei_pkt_cnt_int_enb {
+	uint64_t u64;
+	struct cvmx_npei_pkt_cnt_int_enb_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t port:32;
+#else
+		uint64_t port:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_npei_pkt_data_out_es {
+	uint64_t u64;
+	struct cvmx_npei_pkt_data_out_es_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t es:64;
+#else
+		uint64_t es:64;
+#endif
+	} s;
+};
+
+union cvmx_npei_pkt_data_out_ns {
+	uint64_t u64;
+	struct cvmx_npei_pkt_data_out_ns_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t nsr:32;
+#else
+		uint64_t nsr:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_npei_pkt_data_out_ror {
+	uint64_t u64;
+	struct cvmx_npei_pkt_data_out_ror_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t ror:32;
+#else
+		uint64_t ror:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_npei_pkt_dpaddr {
+	uint64_t u64;
+	struct cvmx_npei_pkt_dpaddr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t dptr:32;
+#else
+		uint64_t dptr:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_npei_pkt_in_bp {
+	uint64_t u64;
+	struct cvmx_npei_pkt_in_bp_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t bp:32;
+#else
+		uint64_t bp:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_npei_pkt_in_donex_cnts {
+	uint64_t u64;
+	struct cvmx_npei_pkt_in_donex_cnts_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t cnt:32;
+#else
+		uint64_t cnt:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_npei_pkt_in_instr_counts {
+	uint64_t u64;
+	struct cvmx_npei_pkt_in_instr_counts_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t wr_cnt:32;
+		uint64_t rd_cnt:32;
+#else
+		uint64_t rd_cnt:32;
+		uint64_t wr_cnt:32;
+#endif
+	} s;
+};
+
+union cvmx_npei_pkt_in_pcie_port {
+	uint64_t u64;
+	struct cvmx_npei_pkt_in_pcie_port_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t pp:64;
+#else
+		uint64_t pp:64;
+#endif
+	} s;
+};
+
+union cvmx_npei_pkt_input_control {
+	uint64_t u64;
+	struct cvmx_npei_pkt_input_control_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_23_63:41;
+		uint64_t pkt_rr:1;
+		uint64_t pbp_dhi:13;
+		uint64_t d_nsr:1;
+		uint64_t d_esr:2;
+		uint64_t d_ror:1;
+		uint64_t use_csr:1;
+		uint64_t nsr:1;
+		uint64_t esr:2;
+		uint64_t ror:1;
+#else
+		uint64_t ror:1;
+		uint64_t esr:2;
+		uint64_t nsr:1;
+		uint64_t use_csr:1;
+		uint64_t d_ror:1;
+		uint64_t d_esr:2;
+		uint64_t d_nsr:1;
+		uint64_t pbp_dhi:13;
+		uint64_t pkt_rr:1;
+		uint64_t reserved_23_63:41;
+#endif
+	} s;
+};
+
+union cvmx_npei_pkt_instr_enb {
+	uint64_t u64;
+	struct cvmx_npei_pkt_instr_enb_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t enb:32;
+#else
+		uint64_t enb:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_npei_pkt_instr_rd_size {
+	uint64_t u64;
+	struct cvmx_npei_pkt_instr_rd_size_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t rdsize:64;
+#else
+		uint64_t rdsize:64;
+#endif
+	} s;
+};
+
+union cvmx_npei_pkt_instr_size {
+	uint64_t u64;
+	struct cvmx_npei_pkt_instr_size_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t is_64b:32;
+#else
+		uint64_t is_64b:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_npei_pkt_int_levels {
+	uint64_t u64;
+	struct cvmx_npei_pkt_int_levels_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_54_63:10;
+		uint64_t time:22;
+		uint64_t cnt:32;
+#else
+		uint64_t cnt:32;
+		uint64_t time:22;
+		uint64_t reserved_54_63:10;
+#endif
+	} s;
+};
+
+union cvmx_npei_pkt_iptr {
+	uint64_t u64;
+	struct cvmx_npei_pkt_iptr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t iptr:32;
+#else
+		uint64_t iptr:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_npei_pkt_out_bmode {
+	uint64_t u64;
+	struct cvmx_npei_pkt_out_bmode_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t bmode:32;
+#else
+		uint64_t bmode:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_npei_pkt_out_enb {
+	uint64_t u64;
+	struct cvmx_npei_pkt_out_enb_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t enb:32;
+#else
+		uint64_t enb:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_npei_pkt_output_wmark {
+	uint64_t u64;
+	struct cvmx_npei_pkt_output_wmark_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t wmark:32;
+#else
+		uint64_t wmark:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_npei_pkt_pcie_port {
+	uint64_t u64;
+	struct cvmx_npei_pkt_pcie_port_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t pp:64;
+#else
+		uint64_t pp:64;
+#endif
+	} s;
+};
+
+union cvmx_npei_pkt_port_in_rst {
+	uint64_t u64;
+	struct cvmx_npei_pkt_port_in_rst_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t in_rst:32;
+		uint64_t out_rst:32;
+#else
+		uint64_t out_rst:32;
+		uint64_t in_rst:32;
+#endif
+	} s;
+};
+
+union cvmx_npei_pkt_slist_es {
+	uint64_t u64;
+	struct cvmx_npei_pkt_slist_es_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t es:64;
+#else
+		uint64_t es:64;
+#endif
+	} s;
+};
+
+union cvmx_npei_pkt_slist_id_size {
+	uint64_t u64;
+	struct cvmx_npei_pkt_slist_id_size_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_23_63:41;
+		uint64_t isize:7;
+		uint64_t bsize:16;
+#else
+		uint64_t bsize:16;
+		uint64_t isize:7;
+		uint64_t reserved_23_63:41;
+#endif
+	} s;
+};
+
+union cvmx_npei_pkt_slist_ns {
+	uint64_t u64;
+	struct cvmx_npei_pkt_slist_ns_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t nsr:32;
+#else
+		uint64_t nsr:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_npei_pkt_slist_ror {
+	uint64_t u64;
+	struct cvmx_npei_pkt_slist_ror_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t ror:32;
+#else
+		uint64_t ror:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_npei_pkt_time_int {
+	uint64_t u64;
+	struct cvmx_npei_pkt_time_int_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t port:32;
+#else
+		uint64_t port:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_npei_pkt_time_int_enb {
+	uint64_t u64;
+	struct cvmx_npei_pkt_time_int_enb_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t port:32;
+#else
+		uint64_t port:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_npei_rsl_int_blocks {
+	uint64_t u64;
+	struct cvmx_npei_rsl_int_blocks_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_31_63:33;
+		uint64_t iob:1;
+		uint64_t lmc1:1;
+		uint64_t agl:1;
+		uint64_t reserved_24_27:4;
+		uint64_t asxpcs1:1;
+		uint64_t asxpcs0:1;
+		uint64_t reserved_21_21:1;
+		uint64_t pip:1;
+		uint64_t spx1:1;
+		uint64_t spx0:1;
+		uint64_t lmc0:1;
+		uint64_t l2c:1;
+		uint64_t usb1:1;
+		uint64_t rad:1;
+		uint64_t usb:1;
+		uint64_t pow:1;
+		uint64_t tim:1;
+		uint64_t pko:1;
+		uint64_t ipd:1;
+		uint64_t reserved_8_8:1;
+		uint64_t zip:1;
+		uint64_t dfa:1;
+		uint64_t fpa:1;
+		uint64_t key:1;
+		uint64_t npei:1;
+		uint64_t gmx1:1;
+		uint64_t gmx0:1;
+		uint64_t mio:1;
+#else
+		uint64_t mio:1;
+		uint64_t gmx0:1;
+		uint64_t gmx1:1;
+		uint64_t npei:1;
+		uint64_t key:1;
+		uint64_t fpa:1;
+		uint64_t dfa:1;
+		uint64_t zip:1;
+		uint64_t reserved_8_8:1;
+		uint64_t ipd:1;
+		uint64_t pko:1;
+		uint64_t tim:1;
+		uint64_t pow:1;
+		uint64_t usb:1;
+		uint64_t rad:1;
+		uint64_t usb1:1;
+		uint64_t l2c:1;
+		uint64_t lmc0:1;
+		uint64_t spx0:1;
+		uint64_t spx1:1;
+		uint64_t pip:1;
+		uint64_t reserved_21_21:1;
+		uint64_t asxpcs0:1;
+		uint64_t asxpcs1:1;
+		uint64_t reserved_24_27:4;
+		uint64_t agl:1;
+		uint64_t lmc1:1;
+		uint64_t iob:1;
+		uint64_t reserved_31_63:33;
+#endif
+	} s;
+};
+
+union cvmx_npei_scratch_1 {
+	uint64_t u64;
+	struct cvmx_npei_scratch_1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t data:64;
+#else
+		uint64_t data:64;
+#endif
+	} s;
+};
+
+union cvmx_npei_state1 {
+	uint64_t u64;
+	struct cvmx_npei_state1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t cpl1:12;
+		uint64_t cpl0:12;
+		uint64_t arb:1;
+		uint64_t csr:39;
+#else
+		uint64_t csr:39;
+		uint64_t arb:1;
+		uint64_t cpl0:12;
+		uint64_t cpl1:12;
+#endif
+	} s;
+};
+
+union cvmx_npei_state2 {
+	uint64_t u64;
+	struct cvmx_npei_state2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t npei:1;
+		uint64_t rac:1;
+		uint64_t csm1:15;
+		uint64_t csm0:15;
+		uint64_t nnp0:8;
+		uint64_t nnd:8;
+#else
+		uint64_t nnd:8;
+		uint64_t nnp0:8;
+		uint64_t csm0:15;
+		uint64_t csm1:15;
+		uint64_t rac:1;
+		uint64_t npei:1;
+		uint64_t reserved_48_63:16;
+#endif
+	} s;
+};
+
+union cvmx_npei_state3 {
+	uint64_t u64;
+	struct cvmx_npei_state3_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_56_63:8;
+		uint64_t psm1:15;
+		uint64_t psm0:15;
+		uint64_t nsm1:13;
+		uint64_t nsm0:13;
+#else
+		uint64_t nsm0:13;
+		uint64_t nsm1:13;
+		uint64_t psm0:15;
+		uint64_t psm1:15;
+		uint64_t reserved_56_63:8;
+#endif
+	} s;
+};
+
+union cvmx_npei_win_rd_addr {
+	uint64_t u64;
+	struct cvmx_npei_win_rd_addr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_51_63:13;
+		uint64_t ld_cmd:2;
+		uint64_t iobit:1;
+		uint64_t rd_addr:48;
+#else
+		uint64_t rd_addr:48;
+		uint64_t iobit:1;
+		uint64_t ld_cmd:2;
+		uint64_t reserved_51_63:13;
+#endif
+	} s;
+};
+
+union cvmx_npei_win_rd_data {
+	uint64_t u64;
+	struct cvmx_npei_win_rd_data_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t rd_data:64;
+#else
+		uint64_t rd_data:64;
+#endif
+	} s;
+};
+
+union cvmx_npei_win_wr_addr {
+	uint64_t u64;
+	struct cvmx_npei_win_wr_addr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_49_63:15;
+		uint64_t iobit:1;
+		uint64_t wr_addr:46;
+		uint64_t reserved_0_1:2;
+#else
+		uint64_t reserved_0_1:2;
+		uint64_t wr_addr:46;
+		uint64_t iobit:1;
+		uint64_t reserved_49_63:15;
+#endif
+	} s;
+};
+
+union cvmx_npei_win_wr_data {
+	uint64_t u64;
+	struct cvmx_npei_win_wr_data_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t wr_data:64;
+#else
+		uint64_t wr_data:64;
+#endif
+	} s;
+};
+
+union cvmx_npei_win_wr_mask {
+	uint64_t u64;
+	struct cvmx_npei_win_wr_mask_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t wr_mask:8;
+#else
+		uint64_t wr_mask:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_npei_window_ctl {
+	uint64_t u64;
+	struct cvmx_npei_window_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t time:32;
+#else
+		uint64_t time:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-npi-defs.h b/arch/mips/include/asm/octeon/cvmx-npi-defs.h
new file mode 100644
index 000000000..ba4967fda
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-npi-defs.h
@@ -0,0 +1,2514 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2012 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_NPI_DEFS_H__
+#define __CVMX_NPI_DEFS_H__
+
+#define CVMX_NPI_BASE_ADDR_INPUT0 CVMX_NPI_BASE_ADDR_INPUTX(0)
+#define CVMX_NPI_BASE_ADDR_INPUT1 CVMX_NPI_BASE_ADDR_INPUTX(1)
+#define CVMX_NPI_BASE_ADDR_INPUT2 CVMX_NPI_BASE_ADDR_INPUTX(2)
+#define CVMX_NPI_BASE_ADDR_INPUT3 CVMX_NPI_BASE_ADDR_INPUTX(3)
+#define CVMX_NPI_BASE_ADDR_INPUTX(offset) (CVMX_ADD_IO_SEG(0x00011F0000000070ull) + ((offset) & 3) * 16)
+#define CVMX_NPI_BASE_ADDR_OUTPUT0 CVMX_NPI_BASE_ADDR_OUTPUTX(0)
+#define CVMX_NPI_BASE_ADDR_OUTPUT1 CVMX_NPI_BASE_ADDR_OUTPUTX(1)
+#define CVMX_NPI_BASE_ADDR_OUTPUT2 CVMX_NPI_BASE_ADDR_OUTPUTX(2)
+#define CVMX_NPI_BASE_ADDR_OUTPUT3 CVMX_NPI_BASE_ADDR_OUTPUTX(3)
+#define CVMX_NPI_BASE_ADDR_OUTPUTX(offset) (CVMX_ADD_IO_SEG(0x00011F00000000B8ull) + ((offset) & 3) * 8)
+#define CVMX_NPI_BIST_STATUS (CVMX_ADD_IO_SEG(0x00011F00000003F8ull))
+#define CVMX_NPI_BUFF_SIZE_OUTPUT0 CVMX_NPI_BUFF_SIZE_OUTPUTX(0)
+#define CVMX_NPI_BUFF_SIZE_OUTPUT1 CVMX_NPI_BUFF_SIZE_OUTPUTX(1)
+#define CVMX_NPI_BUFF_SIZE_OUTPUT2 CVMX_NPI_BUFF_SIZE_OUTPUTX(2)
+#define CVMX_NPI_BUFF_SIZE_OUTPUT3 CVMX_NPI_BUFF_SIZE_OUTPUTX(3)
+#define CVMX_NPI_BUFF_SIZE_OUTPUTX(offset) (CVMX_ADD_IO_SEG(0x00011F00000000E0ull) + ((offset) & 3) * 8)
+#define CVMX_NPI_COMP_CTL (CVMX_ADD_IO_SEG(0x00011F0000000218ull))
+#define CVMX_NPI_CTL_STATUS (CVMX_ADD_IO_SEG(0x00011F0000000010ull))
+#define CVMX_NPI_DBG_SELECT (CVMX_ADD_IO_SEG(0x00011F0000000008ull))
+#define CVMX_NPI_DMA_CONTROL (CVMX_ADD_IO_SEG(0x00011F0000000128ull))
+#define CVMX_NPI_DMA_HIGHP_COUNTS (CVMX_ADD_IO_SEG(0x00011F0000000148ull))
+#define CVMX_NPI_DMA_HIGHP_NADDR (CVMX_ADD_IO_SEG(0x00011F0000000158ull))
+#define CVMX_NPI_DMA_LOWP_COUNTS (CVMX_ADD_IO_SEG(0x00011F0000000140ull))
+#define CVMX_NPI_DMA_LOWP_NADDR (CVMX_ADD_IO_SEG(0x00011F0000000150ull))
+#define CVMX_NPI_HIGHP_DBELL (CVMX_ADD_IO_SEG(0x00011F0000000120ull))
+#define CVMX_NPI_HIGHP_IBUFF_SADDR (CVMX_ADD_IO_SEG(0x00011F0000000110ull))
+#define CVMX_NPI_INPUT_CONTROL (CVMX_ADD_IO_SEG(0x00011F0000000138ull))
+#define CVMX_NPI_INT_ENB (CVMX_ADD_IO_SEG(0x00011F0000000020ull))
+#define CVMX_NPI_INT_SUM (CVMX_ADD_IO_SEG(0x00011F0000000018ull))
+#define CVMX_NPI_LOWP_DBELL (CVMX_ADD_IO_SEG(0x00011F0000000118ull))
+#define CVMX_NPI_LOWP_IBUFF_SADDR (CVMX_ADD_IO_SEG(0x00011F0000000108ull))
+#define CVMX_NPI_MEM_ACCESS_SUBID3 CVMX_NPI_MEM_ACCESS_SUBIDX(3)
+#define CVMX_NPI_MEM_ACCESS_SUBID4 CVMX_NPI_MEM_ACCESS_SUBIDX(4)
+#define CVMX_NPI_MEM_ACCESS_SUBID5 CVMX_NPI_MEM_ACCESS_SUBIDX(5)
+#define CVMX_NPI_MEM_ACCESS_SUBID6 CVMX_NPI_MEM_ACCESS_SUBIDX(6)
+#define CVMX_NPI_MEM_ACCESS_SUBIDX(offset) (CVMX_ADD_IO_SEG(0x00011F0000000028ull) + ((offset) & 7) * 8 - 8*3)
+#define CVMX_NPI_MSI_RCV (0x0000000000000190ull)
+#define CVMX_NPI_NPI_MSI_RCV (CVMX_ADD_IO_SEG(0x00011F0000001190ull))
+#define CVMX_NPI_NUM_DESC_OUTPUT0 CVMX_NPI_NUM_DESC_OUTPUTX(0)
+#define CVMX_NPI_NUM_DESC_OUTPUT1 CVMX_NPI_NUM_DESC_OUTPUTX(1)
+#define CVMX_NPI_NUM_DESC_OUTPUT2 CVMX_NPI_NUM_DESC_OUTPUTX(2)
+#define CVMX_NPI_NUM_DESC_OUTPUT3 CVMX_NPI_NUM_DESC_OUTPUTX(3)
+#define CVMX_NPI_NUM_DESC_OUTPUTX(offset) (CVMX_ADD_IO_SEG(0x00011F0000000050ull) + ((offset) & 3) * 8)
+#define CVMX_NPI_OUTPUT_CONTROL (CVMX_ADD_IO_SEG(0x00011F0000000100ull))
+#define CVMX_NPI_P0_DBPAIR_ADDR CVMX_NPI_PX_DBPAIR_ADDR(0)
+#define CVMX_NPI_P0_INSTR_ADDR CVMX_NPI_PX_INSTR_ADDR(0)
+#define CVMX_NPI_P0_INSTR_CNTS CVMX_NPI_PX_INSTR_CNTS(0)
+#define CVMX_NPI_P0_PAIR_CNTS CVMX_NPI_PX_PAIR_CNTS(0)
+#define CVMX_NPI_P1_DBPAIR_ADDR CVMX_NPI_PX_DBPAIR_ADDR(1)
+#define CVMX_NPI_P1_INSTR_ADDR CVMX_NPI_PX_INSTR_ADDR(1)
+#define CVMX_NPI_P1_INSTR_CNTS CVMX_NPI_PX_INSTR_CNTS(1)
+#define CVMX_NPI_P1_PAIR_CNTS CVMX_NPI_PX_PAIR_CNTS(1)
+#define CVMX_NPI_P2_DBPAIR_ADDR CVMX_NPI_PX_DBPAIR_ADDR(2)
+#define CVMX_NPI_P2_INSTR_ADDR CVMX_NPI_PX_INSTR_ADDR(2)
+#define CVMX_NPI_P2_INSTR_CNTS CVMX_NPI_PX_INSTR_CNTS(2)
+#define CVMX_NPI_P2_PAIR_CNTS CVMX_NPI_PX_PAIR_CNTS(2)
+#define CVMX_NPI_P3_DBPAIR_ADDR CVMX_NPI_PX_DBPAIR_ADDR(3)
+#define CVMX_NPI_P3_INSTR_ADDR CVMX_NPI_PX_INSTR_ADDR(3)
+#define CVMX_NPI_P3_INSTR_CNTS CVMX_NPI_PX_INSTR_CNTS(3)
+#define CVMX_NPI_P3_PAIR_CNTS CVMX_NPI_PX_PAIR_CNTS(3)
+#define CVMX_NPI_PCI_BAR1_INDEXX(offset) (CVMX_ADD_IO_SEG(0x00011F0000001100ull) + ((offset) & 31) * 4)
+#define CVMX_NPI_PCI_BIST_REG (CVMX_ADD_IO_SEG(0x00011F00000011C0ull))
+#define CVMX_NPI_PCI_BURST_SIZE (CVMX_ADD_IO_SEG(0x00011F00000000D8ull))
+#define CVMX_NPI_PCI_CFG00 (CVMX_ADD_IO_SEG(0x00011F0000001800ull))
+#define CVMX_NPI_PCI_CFG01 (CVMX_ADD_IO_SEG(0x00011F0000001804ull))
+#define CVMX_NPI_PCI_CFG02 (CVMX_ADD_IO_SEG(0x00011F0000001808ull))
+#define CVMX_NPI_PCI_CFG03 (CVMX_ADD_IO_SEG(0x00011F000000180Cull))
+#define CVMX_NPI_PCI_CFG04 (CVMX_ADD_IO_SEG(0x00011F0000001810ull))
+#define CVMX_NPI_PCI_CFG05 (CVMX_ADD_IO_SEG(0x00011F0000001814ull))
+#define CVMX_NPI_PCI_CFG06 (CVMX_ADD_IO_SEG(0x00011F0000001818ull))
+#define CVMX_NPI_PCI_CFG07 (CVMX_ADD_IO_SEG(0x00011F000000181Cull))
+#define CVMX_NPI_PCI_CFG08 (CVMX_ADD_IO_SEG(0x00011F0000001820ull))
+#define CVMX_NPI_PCI_CFG09 (CVMX_ADD_IO_SEG(0x00011F0000001824ull))
+#define CVMX_NPI_PCI_CFG10 (CVMX_ADD_IO_SEG(0x00011F0000001828ull))
+#define CVMX_NPI_PCI_CFG11 (CVMX_ADD_IO_SEG(0x00011F000000182Cull))
+#define CVMX_NPI_PCI_CFG12 (CVMX_ADD_IO_SEG(0x00011F0000001830ull))
+#define CVMX_NPI_PCI_CFG13 (CVMX_ADD_IO_SEG(0x00011F0000001834ull))
+#define CVMX_NPI_PCI_CFG15 (CVMX_ADD_IO_SEG(0x00011F000000183Cull))
+#define CVMX_NPI_PCI_CFG16 (CVMX_ADD_IO_SEG(0x00011F0000001840ull))
+#define CVMX_NPI_PCI_CFG17 (CVMX_ADD_IO_SEG(0x00011F0000001844ull))
+#define CVMX_NPI_PCI_CFG18 (CVMX_ADD_IO_SEG(0x00011F0000001848ull))
+#define CVMX_NPI_PCI_CFG19 (CVMX_ADD_IO_SEG(0x00011F000000184Cull))
+#define CVMX_NPI_PCI_CFG20 (CVMX_ADD_IO_SEG(0x00011F0000001850ull))
+#define CVMX_NPI_PCI_CFG21 (CVMX_ADD_IO_SEG(0x00011F0000001854ull))
+#define CVMX_NPI_PCI_CFG22 (CVMX_ADD_IO_SEG(0x00011F0000001858ull))
+#define CVMX_NPI_PCI_CFG56 (CVMX_ADD_IO_SEG(0x00011F00000018E0ull))
+#define CVMX_NPI_PCI_CFG57 (CVMX_ADD_IO_SEG(0x00011F00000018E4ull))
+#define CVMX_NPI_PCI_CFG58 (CVMX_ADD_IO_SEG(0x00011F00000018E8ull))
+#define CVMX_NPI_PCI_CFG59 (CVMX_ADD_IO_SEG(0x00011F00000018ECull))
+#define CVMX_NPI_PCI_CFG60 (CVMX_ADD_IO_SEG(0x00011F00000018F0ull))
+#define CVMX_NPI_PCI_CFG61 (CVMX_ADD_IO_SEG(0x00011F00000018F4ull))
+#define CVMX_NPI_PCI_CFG62 (CVMX_ADD_IO_SEG(0x00011F00000018F8ull))
+#define CVMX_NPI_PCI_CFG63 (CVMX_ADD_IO_SEG(0x00011F00000018FCull))
+#define CVMX_NPI_PCI_CNT_REG (CVMX_ADD_IO_SEG(0x00011F00000011B8ull))
+#define CVMX_NPI_PCI_CTL_STATUS_2 (CVMX_ADD_IO_SEG(0x00011F000000118Cull))
+#define CVMX_NPI_PCI_INT_ARB_CFG (CVMX_ADD_IO_SEG(0x00011F0000000130ull))
+#define CVMX_NPI_PCI_INT_ENB2 (CVMX_ADD_IO_SEG(0x00011F00000011A0ull))
+#define CVMX_NPI_PCI_INT_SUM2 (CVMX_ADD_IO_SEG(0x00011F0000001198ull))
+#define CVMX_NPI_PCI_READ_CMD (CVMX_ADD_IO_SEG(0x00011F0000000048ull))
+#define CVMX_NPI_PCI_READ_CMD_6 (CVMX_ADD_IO_SEG(0x00011F0000001180ull))
+#define CVMX_NPI_PCI_READ_CMD_C (CVMX_ADD_IO_SEG(0x00011F0000001184ull))
+#define CVMX_NPI_PCI_READ_CMD_E (CVMX_ADD_IO_SEG(0x00011F0000001188ull))
+#define CVMX_NPI_PCI_SCM_REG (CVMX_ADD_IO_SEG(0x00011F00000011A8ull))
+#define CVMX_NPI_PCI_TSR_REG (CVMX_ADD_IO_SEG(0x00011F00000011B0ull))
+#define CVMX_NPI_PORT32_INSTR_HDR (CVMX_ADD_IO_SEG(0x00011F00000001F8ull))
+#define CVMX_NPI_PORT33_INSTR_HDR (CVMX_ADD_IO_SEG(0x00011F0000000200ull))
+#define CVMX_NPI_PORT34_INSTR_HDR (CVMX_ADD_IO_SEG(0x00011F0000000208ull))
+#define CVMX_NPI_PORT35_INSTR_HDR (CVMX_ADD_IO_SEG(0x00011F0000000210ull))
+#define CVMX_NPI_PORT_BP_CONTROL (CVMX_ADD_IO_SEG(0x00011F00000001F0ull))
+#define CVMX_NPI_PX_DBPAIR_ADDR(offset) (CVMX_ADD_IO_SEG(0x00011F0000000180ull) + ((offset) & 3) * 8)
+#define CVMX_NPI_PX_INSTR_ADDR(offset) (CVMX_ADD_IO_SEG(0x00011F00000001C0ull) + ((offset) & 3) * 8)
+#define CVMX_NPI_PX_INSTR_CNTS(offset) (CVMX_ADD_IO_SEG(0x00011F00000001A0ull) + ((offset) & 3) * 8)
+#define CVMX_NPI_PX_PAIR_CNTS(offset) (CVMX_ADD_IO_SEG(0x00011F0000000160ull) + ((offset) & 3) * 8)
+#define CVMX_NPI_RSL_INT_BLOCKS (CVMX_ADD_IO_SEG(0x00011F0000000000ull))
+#define CVMX_NPI_SIZE_INPUT0 CVMX_NPI_SIZE_INPUTX(0)
+#define CVMX_NPI_SIZE_INPUT1 CVMX_NPI_SIZE_INPUTX(1)
+#define CVMX_NPI_SIZE_INPUT2 CVMX_NPI_SIZE_INPUTX(2)
+#define CVMX_NPI_SIZE_INPUT3 CVMX_NPI_SIZE_INPUTX(3)
+#define CVMX_NPI_SIZE_INPUTX(offset) (CVMX_ADD_IO_SEG(0x00011F0000000078ull) + ((offset) & 3) * 16)
+#define CVMX_NPI_WIN_READ_TO (CVMX_ADD_IO_SEG(0x00011F00000001E0ull))
+
+union cvmx_npi_base_addr_inputx {
+	uint64_t u64;
+	struct cvmx_npi_base_addr_inputx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t baddr:61;
+		uint64_t reserved_0_2:3;
+#else
+		uint64_t reserved_0_2:3;
+		uint64_t baddr:61;
+#endif
+	} s;
+};
+
+union cvmx_npi_base_addr_outputx {
+	uint64_t u64;
+	struct cvmx_npi_base_addr_outputx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t baddr:61;
+		uint64_t reserved_0_2:3;
+#else
+		uint64_t reserved_0_2:3;
+		uint64_t baddr:61;
+#endif
+	} s;
+};
+
+union cvmx_npi_bist_status {
+	uint64_t u64;
+	struct cvmx_npi_bist_status_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t csr_bs:1;
+		uint64_t dif_bs:1;
+		uint64_t rdp_bs:1;
+		uint64_t pcnc_bs:1;
+		uint64_t pcn_bs:1;
+		uint64_t rdn_bs:1;
+		uint64_t pcac_bs:1;
+		uint64_t pcad_bs:1;
+		uint64_t rdnl_bs:1;
+		uint64_t pgf_bs:1;
+		uint64_t pig_bs:1;
+		uint64_t pof0_bs:1;
+		uint64_t pof1_bs:1;
+		uint64_t pof2_bs:1;
+		uint64_t pof3_bs:1;
+		uint64_t pos_bs:1;
+		uint64_t nus_bs:1;
+		uint64_t dob_bs:1;
+		uint64_t pdf_bs:1;
+		uint64_t dpi_bs:1;
+#else
+		uint64_t dpi_bs:1;
+		uint64_t pdf_bs:1;
+		uint64_t dob_bs:1;
+		uint64_t nus_bs:1;
+		uint64_t pos_bs:1;
+		uint64_t pof3_bs:1;
+		uint64_t pof2_bs:1;
+		uint64_t pof1_bs:1;
+		uint64_t pof0_bs:1;
+		uint64_t pig_bs:1;
+		uint64_t pgf_bs:1;
+		uint64_t rdnl_bs:1;
+		uint64_t pcad_bs:1;
+		uint64_t pcac_bs:1;
+		uint64_t rdn_bs:1;
+		uint64_t pcn_bs:1;
+		uint64_t pcnc_bs:1;
+		uint64_t rdp_bs:1;
+		uint64_t dif_bs:1;
+		uint64_t csr_bs:1;
+		uint64_t reserved_20_63:44;
+#endif
+	} s;
+	struct cvmx_npi_bist_status_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t csr_bs:1;
+		uint64_t dif_bs:1;
+		uint64_t rdp_bs:1;
+		uint64_t pcnc_bs:1;
+		uint64_t pcn_bs:1;
+		uint64_t rdn_bs:1;
+		uint64_t pcac_bs:1;
+		uint64_t pcad_bs:1;
+		uint64_t rdnl_bs:1;
+		uint64_t pgf_bs:1;
+		uint64_t pig_bs:1;
+		uint64_t pof0_bs:1;
+		uint64_t reserved_5_7:3;
+		uint64_t pos_bs:1;
+		uint64_t nus_bs:1;
+		uint64_t dob_bs:1;
+		uint64_t pdf_bs:1;
+		uint64_t dpi_bs:1;
+#else
+		uint64_t dpi_bs:1;
+		uint64_t pdf_bs:1;
+		uint64_t dob_bs:1;
+		uint64_t nus_bs:1;
+		uint64_t pos_bs:1;
+		uint64_t reserved_5_7:3;
+		uint64_t pof0_bs:1;
+		uint64_t pig_bs:1;
+		uint64_t pgf_bs:1;
+		uint64_t rdnl_bs:1;
+		uint64_t pcad_bs:1;
+		uint64_t pcac_bs:1;
+		uint64_t rdn_bs:1;
+		uint64_t pcn_bs:1;
+		uint64_t pcnc_bs:1;
+		uint64_t rdp_bs:1;
+		uint64_t dif_bs:1;
+		uint64_t csr_bs:1;
+		uint64_t reserved_20_63:44;
+#endif
+	} cn30xx;
+	struct cvmx_npi_bist_status_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t csr_bs:1;
+		uint64_t dif_bs:1;
+		uint64_t rdp_bs:1;
+		uint64_t pcnc_bs:1;
+		uint64_t pcn_bs:1;
+		uint64_t rdn_bs:1;
+		uint64_t pcac_bs:1;
+		uint64_t pcad_bs:1;
+		uint64_t rdnl_bs:1;
+		uint64_t pgf_bs:1;
+		uint64_t pig_bs:1;
+		uint64_t pof0_bs:1;
+		uint64_t pof1_bs:1;
+		uint64_t reserved_5_6:2;
+		uint64_t pos_bs:1;
+		uint64_t nus_bs:1;
+		uint64_t dob_bs:1;
+		uint64_t pdf_bs:1;
+		uint64_t dpi_bs:1;
+#else
+		uint64_t dpi_bs:1;
+		uint64_t pdf_bs:1;
+		uint64_t dob_bs:1;
+		uint64_t nus_bs:1;
+		uint64_t pos_bs:1;
+		uint64_t reserved_5_6:2;
+		uint64_t pof1_bs:1;
+		uint64_t pof0_bs:1;
+		uint64_t pig_bs:1;
+		uint64_t pgf_bs:1;
+		uint64_t rdnl_bs:1;
+		uint64_t pcad_bs:1;
+		uint64_t pcac_bs:1;
+		uint64_t rdn_bs:1;
+		uint64_t pcn_bs:1;
+		uint64_t pcnc_bs:1;
+		uint64_t rdp_bs:1;
+		uint64_t dif_bs:1;
+		uint64_t csr_bs:1;
+		uint64_t reserved_20_63:44;
+#endif
+	} cn50xx;
+};
+
+union cvmx_npi_buff_size_outputx {
+	uint64_t u64;
+	struct cvmx_npi_buff_size_outputx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_23_63:41;
+		uint64_t isize:7;
+		uint64_t bsize:16;
+#else
+		uint64_t bsize:16;
+		uint64_t isize:7;
+		uint64_t reserved_23_63:41;
+#endif
+	} s;
+};
+
+union cvmx_npi_comp_ctl {
+	uint64_t u64;
+	struct cvmx_npi_comp_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t pctl:5;
+		uint64_t nctl:5;
+#else
+		uint64_t nctl:5;
+		uint64_t pctl:5;
+		uint64_t reserved_10_63:54;
+#endif
+	} s;
+};
+
+union cvmx_npi_ctl_status {
+	uint64_t u64;
+	struct cvmx_npi_ctl_status_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_63_63:1;
+		uint64_t chip_rev:8;
+		uint64_t dis_pniw:1;
+		uint64_t out3_enb:1;
+		uint64_t out2_enb:1;
+		uint64_t out1_enb:1;
+		uint64_t out0_enb:1;
+		uint64_t ins3_enb:1;
+		uint64_t ins2_enb:1;
+		uint64_t ins1_enb:1;
+		uint64_t ins0_enb:1;
+		uint64_t ins3_64b:1;
+		uint64_t ins2_64b:1;
+		uint64_t ins1_64b:1;
+		uint64_t ins0_64b:1;
+		uint64_t pci_wdis:1;
+		uint64_t wait_com:1;
+		uint64_t reserved_37_39:3;
+		uint64_t max_word:5;
+		uint64_t reserved_10_31:22;
+		uint64_t timer:10;
+#else
+		uint64_t timer:10;
+		uint64_t reserved_10_31:22;
+		uint64_t max_word:5;
+		uint64_t reserved_37_39:3;
+		uint64_t wait_com:1;
+		uint64_t pci_wdis:1;
+		uint64_t ins0_64b:1;
+		uint64_t ins1_64b:1;
+		uint64_t ins2_64b:1;
+		uint64_t ins3_64b:1;
+		uint64_t ins0_enb:1;
+		uint64_t ins1_enb:1;
+		uint64_t ins2_enb:1;
+		uint64_t ins3_enb:1;
+		uint64_t out0_enb:1;
+		uint64_t out1_enb:1;
+		uint64_t out2_enb:1;
+		uint64_t out3_enb:1;
+		uint64_t dis_pniw:1;
+		uint64_t chip_rev:8;
+		uint64_t reserved_63_63:1;
+#endif
+	} s;
+	struct cvmx_npi_ctl_status_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_63_63:1;
+		uint64_t chip_rev:8;
+		uint64_t dis_pniw:1;
+		uint64_t reserved_51_53:3;
+		uint64_t out0_enb:1;
+		uint64_t reserved_47_49:3;
+		uint64_t ins0_enb:1;
+		uint64_t reserved_43_45:3;
+		uint64_t ins0_64b:1;
+		uint64_t pci_wdis:1;
+		uint64_t wait_com:1;
+		uint64_t reserved_37_39:3;
+		uint64_t max_word:5;
+		uint64_t reserved_10_31:22;
+		uint64_t timer:10;
+#else
+		uint64_t timer:10;
+		uint64_t reserved_10_31:22;
+		uint64_t max_word:5;
+		uint64_t reserved_37_39:3;
+		uint64_t wait_com:1;
+		uint64_t pci_wdis:1;
+		uint64_t ins0_64b:1;
+		uint64_t reserved_43_45:3;
+		uint64_t ins0_enb:1;
+		uint64_t reserved_47_49:3;
+		uint64_t out0_enb:1;
+		uint64_t reserved_51_53:3;
+		uint64_t dis_pniw:1;
+		uint64_t chip_rev:8;
+		uint64_t reserved_63_63:1;
+#endif
+	} cn30xx;
+	struct cvmx_npi_ctl_status_cn31xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_63_63:1;
+		uint64_t chip_rev:8;
+		uint64_t dis_pniw:1;
+		uint64_t reserved_52_53:2;
+		uint64_t out1_enb:1;
+		uint64_t out0_enb:1;
+		uint64_t reserved_48_49:2;
+		uint64_t ins1_enb:1;
+		uint64_t ins0_enb:1;
+		uint64_t reserved_44_45:2;
+		uint64_t ins1_64b:1;
+		uint64_t ins0_64b:1;
+		uint64_t pci_wdis:1;
+		uint64_t wait_com:1;
+		uint64_t reserved_37_39:3;
+		uint64_t max_word:5;
+		uint64_t reserved_10_31:22;
+		uint64_t timer:10;
+#else
+		uint64_t timer:10;
+		uint64_t reserved_10_31:22;
+		uint64_t max_word:5;
+		uint64_t reserved_37_39:3;
+		uint64_t wait_com:1;
+		uint64_t pci_wdis:1;
+		uint64_t ins0_64b:1;
+		uint64_t ins1_64b:1;
+		uint64_t reserved_44_45:2;
+		uint64_t ins0_enb:1;
+		uint64_t ins1_enb:1;
+		uint64_t reserved_48_49:2;
+		uint64_t out0_enb:1;
+		uint64_t out1_enb:1;
+		uint64_t reserved_52_53:2;
+		uint64_t dis_pniw:1;
+		uint64_t chip_rev:8;
+		uint64_t reserved_63_63:1;
+#endif
+	} cn31xx;
+};
+
+union cvmx_npi_dbg_select {
+	uint64_t u64;
+	struct cvmx_npi_dbg_select_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t dbg_sel:16;
+#else
+		uint64_t dbg_sel:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_npi_dma_control {
+	uint64_t u64;
+	struct cvmx_npi_dma_control_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_36_63:28;
+		uint64_t b0_lend:1;
+		uint64_t dwb_denb:1;
+		uint64_t dwb_ichk:9;
+		uint64_t fpa_que:3;
+		uint64_t o_add1:1;
+		uint64_t o_ro:1;
+		uint64_t o_ns:1;
+		uint64_t o_es:2;
+		uint64_t o_mode:1;
+		uint64_t hp_enb:1;
+		uint64_t lp_enb:1;
+		uint64_t csize:14;
+#else
+		uint64_t csize:14;
+		uint64_t lp_enb:1;
+		uint64_t hp_enb:1;
+		uint64_t o_mode:1;
+		uint64_t o_es:2;
+		uint64_t o_ns:1;
+		uint64_t o_ro:1;
+		uint64_t o_add1:1;
+		uint64_t fpa_que:3;
+		uint64_t dwb_ichk:9;
+		uint64_t dwb_denb:1;
+		uint64_t b0_lend:1;
+		uint64_t reserved_36_63:28;
+#endif
+	} s;
+};
+
+union cvmx_npi_dma_highp_counts {
+	uint64_t u64;
+	struct cvmx_npi_dma_highp_counts_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_39_63:25;
+		uint64_t fcnt:7;
+		uint64_t dbell:32;
+#else
+		uint64_t dbell:32;
+		uint64_t fcnt:7;
+		uint64_t reserved_39_63:25;
+#endif
+	} s;
+};
+
+union cvmx_npi_dma_highp_naddr {
+	uint64_t u64;
+	struct cvmx_npi_dma_highp_naddr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_40_63:24;
+		uint64_t state:4;
+		uint64_t addr:36;
+#else
+		uint64_t addr:36;
+		uint64_t state:4;
+		uint64_t reserved_40_63:24;
+#endif
+	} s;
+};
+
+union cvmx_npi_dma_lowp_counts {
+	uint64_t u64;
+	struct cvmx_npi_dma_lowp_counts_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_39_63:25;
+		uint64_t fcnt:7;
+		uint64_t dbell:32;
+#else
+		uint64_t dbell:32;
+		uint64_t fcnt:7;
+		uint64_t reserved_39_63:25;
+#endif
+	} s;
+};
+
+union cvmx_npi_dma_lowp_naddr {
+	uint64_t u64;
+	struct cvmx_npi_dma_lowp_naddr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_40_63:24;
+		uint64_t state:4;
+		uint64_t addr:36;
+#else
+		uint64_t addr:36;
+		uint64_t state:4;
+		uint64_t reserved_40_63:24;
+#endif
+	} s;
+};
+
+union cvmx_npi_highp_dbell {
+	uint64_t u64;
+	struct cvmx_npi_highp_dbell_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t dbell:16;
+#else
+		uint64_t dbell:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_npi_highp_ibuff_saddr {
+	uint64_t u64;
+	struct cvmx_npi_highp_ibuff_saddr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_36_63:28;
+		uint64_t saddr:36;
+#else
+		uint64_t saddr:36;
+		uint64_t reserved_36_63:28;
+#endif
+	} s;
+};
+
+union cvmx_npi_input_control {
+	uint64_t u64;
+	struct cvmx_npi_input_control_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_23_63:41;
+		uint64_t pkt_rr:1;
+		uint64_t pbp_dhi:13;
+		uint64_t d_nsr:1;
+		uint64_t d_esr:2;
+		uint64_t d_ror:1;
+		uint64_t use_csr:1;
+		uint64_t nsr:1;
+		uint64_t esr:2;
+		uint64_t ror:1;
+#else
+		uint64_t ror:1;
+		uint64_t esr:2;
+		uint64_t nsr:1;
+		uint64_t use_csr:1;
+		uint64_t d_ror:1;
+		uint64_t d_esr:2;
+		uint64_t d_nsr:1;
+		uint64_t pbp_dhi:13;
+		uint64_t pkt_rr:1;
+		uint64_t reserved_23_63:41;
+#endif
+	} s;
+	struct cvmx_npi_input_control_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_22_63:42;
+		uint64_t pbp_dhi:13;
+		uint64_t d_nsr:1;
+		uint64_t d_esr:2;
+		uint64_t d_ror:1;
+		uint64_t use_csr:1;
+		uint64_t nsr:1;
+		uint64_t esr:2;
+		uint64_t ror:1;
+#else
+		uint64_t ror:1;
+		uint64_t esr:2;
+		uint64_t nsr:1;
+		uint64_t use_csr:1;
+		uint64_t d_ror:1;
+		uint64_t d_esr:2;
+		uint64_t d_nsr:1;
+		uint64_t pbp_dhi:13;
+		uint64_t reserved_22_63:42;
+#endif
+	} cn30xx;
+};
+
+union cvmx_npi_int_enb {
+	uint64_t u64;
+	struct cvmx_npi_int_enb_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_62_63:2;
+		uint64_t q1_a_f:1;
+		uint64_t q1_s_e:1;
+		uint64_t pdf_p_f:1;
+		uint64_t pdf_p_e:1;
+		uint64_t pcf_p_f:1;
+		uint64_t pcf_p_e:1;
+		uint64_t rdx_s_e:1;
+		uint64_t rwx_s_e:1;
+		uint64_t pnc_a_f:1;
+		uint64_t pnc_s_e:1;
+		uint64_t com_a_f:1;
+		uint64_t com_s_e:1;
+		uint64_t q3_a_f:1;
+		uint64_t q3_s_e:1;
+		uint64_t q2_a_f:1;
+		uint64_t q2_s_e:1;
+		uint64_t pcr_a_f:1;
+		uint64_t pcr_s_e:1;
+		uint64_t fcr_a_f:1;
+		uint64_t fcr_s_e:1;
+		uint64_t iobdma:1;
+		uint64_t p_dperr:1;
+		uint64_t win_rto:1;
+		uint64_t i3_pperr:1;
+		uint64_t i2_pperr:1;
+		uint64_t i1_pperr:1;
+		uint64_t i0_pperr:1;
+		uint64_t p3_ptout:1;
+		uint64_t p2_ptout:1;
+		uint64_t p1_ptout:1;
+		uint64_t p0_ptout:1;
+		uint64_t p3_pperr:1;
+		uint64_t p2_pperr:1;
+		uint64_t p1_pperr:1;
+		uint64_t p0_pperr:1;
+		uint64_t g3_rtout:1;
+		uint64_t g2_rtout:1;
+		uint64_t g1_rtout:1;
+		uint64_t g0_rtout:1;
+		uint64_t p3_perr:1;
+		uint64_t p2_perr:1;
+		uint64_t p1_perr:1;
+		uint64_t p0_perr:1;
+		uint64_t p3_rtout:1;
+		uint64_t p2_rtout:1;
+		uint64_t p1_rtout:1;
+		uint64_t p0_rtout:1;
+		uint64_t i3_overf:1;
+		uint64_t i2_overf:1;
+		uint64_t i1_overf:1;
+		uint64_t i0_overf:1;
+		uint64_t i3_rtout:1;
+		uint64_t i2_rtout:1;
+		uint64_t i1_rtout:1;
+		uint64_t i0_rtout:1;
+		uint64_t po3_2sml:1;
+		uint64_t po2_2sml:1;
+		uint64_t po1_2sml:1;
+		uint64_t po0_2sml:1;
+		uint64_t pci_rsl:1;
+		uint64_t rml_wto:1;
+		uint64_t rml_rto:1;
+#else
+		uint64_t rml_rto:1;
+		uint64_t rml_wto:1;
+		uint64_t pci_rsl:1;
+		uint64_t po0_2sml:1;
+		uint64_t po1_2sml:1;
+		uint64_t po2_2sml:1;
+		uint64_t po3_2sml:1;
+		uint64_t i0_rtout:1;
+		uint64_t i1_rtout:1;
+		uint64_t i2_rtout:1;
+		uint64_t i3_rtout:1;
+		uint64_t i0_overf:1;
+		uint64_t i1_overf:1;
+		uint64_t i2_overf:1;
+		uint64_t i3_overf:1;
+		uint64_t p0_rtout:1;
+		uint64_t p1_rtout:1;
+		uint64_t p2_rtout:1;
+		uint64_t p3_rtout:1;
+		uint64_t p0_perr:1;
+		uint64_t p1_perr:1;
+		uint64_t p2_perr:1;
+		uint64_t p3_perr:1;
+		uint64_t g0_rtout:1;
+		uint64_t g1_rtout:1;
+		uint64_t g2_rtout:1;
+		uint64_t g3_rtout:1;
+		uint64_t p0_pperr:1;
+		uint64_t p1_pperr:1;
+		uint64_t p2_pperr:1;
+		uint64_t p3_pperr:1;
+		uint64_t p0_ptout:1;
+		uint64_t p1_ptout:1;
+		uint64_t p2_ptout:1;
+		uint64_t p3_ptout:1;
+		uint64_t i0_pperr:1;
+		uint64_t i1_pperr:1;
+		uint64_t i2_pperr:1;
+		uint64_t i3_pperr:1;
+		uint64_t win_rto:1;
+		uint64_t p_dperr:1;
+		uint64_t iobdma:1;
+		uint64_t fcr_s_e:1;
+		uint64_t fcr_a_f:1;
+		uint64_t pcr_s_e:1;
+		uint64_t pcr_a_f:1;
+		uint64_t q2_s_e:1;
+		uint64_t q2_a_f:1;
+		uint64_t q3_s_e:1;
+		uint64_t q3_a_f:1;
+		uint64_t com_s_e:1;
+		uint64_t com_a_f:1;
+		uint64_t pnc_s_e:1;
+		uint64_t pnc_a_f:1;
+		uint64_t rwx_s_e:1;
+		uint64_t rdx_s_e:1;
+		uint64_t pcf_p_e:1;
+		uint64_t pcf_p_f:1;
+		uint64_t pdf_p_e:1;
+		uint64_t pdf_p_f:1;
+		uint64_t q1_s_e:1;
+		uint64_t q1_a_f:1;
+		uint64_t reserved_62_63:2;
+#endif
+	} s;
+	struct cvmx_npi_int_enb_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_62_63:2;
+		uint64_t q1_a_f:1;
+		uint64_t q1_s_e:1;
+		uint64_t pdf_p_f:1;
+		uint64_t pdf_p_e:1;
+		uint64_t pcf_p_f:1;
+		uint64_t pcf_p_e:1;
+		uint64_t rdx_s_e:1;
+		uint64_t rwx_s_e:1;
+		uint64_t pnc_a_f:1;
+		uint64_t pnc_s_e:1;
+		uint64_t com_a_f:1;
+		uint64_t com_s_e:1;
+		uint64_t q3_a_f:1;
+		uint64_t q3_s_e:1;
+		uint64_t q2_a_f:1;
+		uint64_t q2_s_e:1;
+		uint64_t pcr_a_f:1;
+		uint64_t pcr_s_e:1;
+		uint64_t fcr_a_f:1;
+		uint64_t fcr_s_e:1;
+		uint64_t iobdma:1;
+		uint64_t p_dperr:1;
+		uint64_t win_rto:1;
+		uint64_t reserved_36_38:3;
+		uint64_t i0_pperr:1;
+		uint64_t reserved_32_34:3;
+		uint64_t p0_ptout:1;
+		uint64_t reserved_28_30:3;
+		uint64_t p0_pperr:1;
+		uint64_t reserved_24_26:3;
+		uint64_t g0_rtout:1;
+		uint64_t reserved_20_22:3;
+		uint64_t p0_perr:1;
+		uint64_t reserved_16_18:3;
+		uint64_t p0_rtout:1;
+		uint64_t reserved_12_14:3;
+		uint64_t i0_overf:1;
+		uint64_t reserved_8_10:3;
+		uint64_t i0_rtout:1;
+		uint64_t reserved_4_6:3;
+		uint64_t po0_2sml:1;
+		uint64_t pci_rsl:1;
+		uint64_t rml_wto:1;
+		uint64_t rml_rto:1;
+#else
+		uint64_t rml_rto:1;
+		uint64_t rml_wto:1;
+		uint64_t pci_rsl:1;
+		uint64_t po0_2sml:1;
+		uint64_t reserved_4_6:3;
+		uint64_t i0_rtout:1;
+		uint64_t reserved_8_10:3;
+		uint64_t i0_overf:1;
+		uint64_t reserved_12_14:3;
+		uint64_t p0_rtout:1;
+		uint64_t reserved_16_18:3;
+		uint64_t p0_perr:1;
+		uint64_t reserved_20_22:3;
+		uint64_t g0_rtout:1;
+		uint64_t reserved_24_26:3;
+		uint64_t p0_pperr:1;
+		uint64_t reserved_28_30:3;
+		uint64_t p0_ptout:1;
+		uint64_t reserved_32_34:3;
+		uint64_t i0_pperr:1;
+		uint64_t reserved_36_38:3;
+		uint64_t win_rto:1;
+		uint64_t p_dperr:1;
+		uint64_t iobdma:1;
+		uint64_t fcr_s_e:1;
+		uint64_t fcr_a_f:1;
+		uint64_t pcr_s_e:1;
+		uint64_t pcr_a_f:1;
+		uint64_t q2_s_e:1;
+		uint64_t q2_a_f:1;
+		uint64_t q3_s_e:1;
+		uint64_t q3_a_f:1;
+		uint64_t com_s_e:1;
+		uint64_t com_a_f:1;
+		uint64_t pnc_s_e:1;
+		uint64_t pnc_a_f:1;
+		uint64_t rwx_s_e:1;
+		uint64_t rdx_s_e:1;
+		uint64_t pcf_p_e:1;
+		uint64_t pcf_p_f:1;
+		uint64_t pdf_p_e:1;
+		uint64_t pdf_p_f:1;
+		uint64_t q1_s_e:1;
+		uint64_t q1_a_f:1;
+		uint64_t reserved_62_63:2;
+#endif
+	} cn30xx;
+	struct cvmx_npi_int_enb_cn31xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_62_63:2;
+		uint64_t q1_a_f:1;
+		uint64_t q1_s_e:1;
+		uint64_t pdf_p_f:1;
+		uint64_t pdf_p_e:1;
+		uint64_t pcf_p_f:1;
+		uint64_t pcf_p_e:1;
+		uint64_t rdx_s_e:1;
+		uint64_t rwx_s_e:1;
+		uint64_t pnc_a_f:1;
+		uint64_t pnc_s_e:1;
+		uint64_t com_a_f:1;
+		uint64_t com_s_e:1;
+		uint64_t q3_a_f:1;
+		uint64_t q3_s_e:1;
+		uint64_t q2_a_f:1;
+		uint64_t q2_s_e:1;
+		uint64_t pcr_a_f:1;
+		uint64_t pcr_s_e:1;
+		uint64_t fcr_a_f:1;
+		uint64_t fcr_s_e:1;
+		uint64_t iobdma:1;
+		uint64_t p_dperr:1;
+		uint64_t win_rto:1;
+		uint64_t reserved_37_38:2;
+		uint64_t i1_pperr:1;
+		uint64_t i0_pperr:1;
+		uint64_t reserved_33_34:2;
+		uint64_t p1_ptout:1;
+		uint64_t p0_ptout:1;
+		uint64_t reserved_29_30:2;
+		uint64_t p1_pperr:1;
+		uint64_t p0_pperr:1;
+		uint64_t reserved_25_26:2;
+		uint64_t g1_rtout:1;
+		uint64_t g0_rtout:1;
+		uint64_t reserved_21_22:2;
+		uint64_t p1_perr:1;
+		uint64_t p0_perr:1;
+		uint64_t reserved_17_18:2;
+		uint64_t p1_rtout:1;
+		uint64_t p0_rtout:1;
+		uint64_t reserved_13_14:2;
+		uint64_t i1_overf:1;
+		uint64_t i0_overf:1;
+		uint64_t reserved_9_10:2;
+		uint64_t i1_rtout:1;
+		uint64_t i0_rtout:1;
+		uint64_t reserved_5_6:2;
+		uint64_t po1_2sml:1;
+		uint64_t po0_2sml:1;
+		uint64_t pci_rsl:1;
+		uint64_t rml_wto:1;
+		uint64_t rml_rto:1;
+#else
+		uint64_t rml_rto:1;
+		uint64_t rml_wto:1;
+		uint64_t pci_rsl:1;
+		uint64_t po0_2sml:1;
+		uint64_t po1_2sml:1;
+		uint64_t reserved_5_6:2;
+		uint64_t i0_rtout:1;
+		uint64_t i1_rtout:1;
+		uint64_t reserved_9_10:2;
+		uint64_t i0_overf:1;
+		uint64_t i1_overf:1;
+		uint64_t reserved_13_14:2;
+		uint64_t p0_rtout:1;
+		uint64_t p1_rtout:1;
+		uint64_t reserved_17_18:2;
+		uint64_t p0_perr:1;
+		uint64_t p1_perr:1;
+		uint64_t reserved_21_22:2;
+		uint64_t g0_rtout:1;
+		uint64_t g1_rtout:1;
+		uint64_t reserved_25_26:2;
+		uint64_t p0_pperr:1;
+		uint64_t p1_pperr:1;
+		uint64_t reserved_29_30:2;
+		uint64_t p0_ptout:1;
+		uint64_t p1_ptout:1;
+		uint64_t reserved_33_34:2;
+		uint64_t i0_pperr:1;
+		uint64_t i1_pperr:1;
+		uint64_t reserved_37_38:2;
+		uint64_t win_rto:1;
+		uint64_t p_dperr:1;
+		uint64_t iobdma:1;
+		uint64_t fcr_s_e:1;
+		uint64_t fcr_a_f:1;
+		uint64_t pcr_s_e:1;
+		uint64_t pcr_a_f:1;
+		uint64_t q2_s_e:1;
+		uint64_t q2_a_f:1;
+		uint64_t q3_s_e:1;
+		uint64_t q3_a_f:1;
+		uint64_t com_s_e:1;
+		uint64_t com_a_f:1;
+		uint64_t pnc_s_e:1;
+		uint64_t pnc_a_f:1;
+		uint64_t rwx_s_e:1;
+		uint64_t rdx_s_e:1;
+		uint64_t pcf_p_e:1;
+		uint64_t pcf_p_f:1;
+		uint64_t pdf_p_e:1;
+		uint64_t pdf_p_f:1;
+		uint64_t q1_s_e:1;
+		uint64_t q1_a_f:1;
+		uint64_t reserved_62_63:2;
+#endif
+	} cn31xx;
+	struct cvmx_npi_int_enb_cn38xxp2 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_42_63:22;
+		uint64_t iobdma:1;
+		uint64_t p_dperr:1;
+		uint64_t win_rto:1;
+		uint64_t i3_pperr:1;
+		uint64_t i2_pperr:1;
+		uint64_t i1_pperr:1;
+		uint64_t i0_pperr:1;
+		uint64_t p3_ptout:1;
+		uint64_t p2_ptout:1;
+		uint64_t p1_ptout:1;
+		uint64_t p0_ptout:1;
+		uint64_t p3_pperr:1;
+		uint64_t p2_pperr:1;
+		uint64_t p1_pperr:1;
+		uint64_t p0_pperr:1;
+		uint64_t g3_rtout:1;
+		uint64_t g2_rtout:1;
+		uint64_t g1_rtout:1;
+		uint64_t g0_rtout:1;
+		uint64_t p3_perr:1;
+		uint64_t p2_perr:1;
+		uint64_t p1_perr:1;
+		uint64_t p0_perr:1;
+		uint64_t p3_rtout:1;
+		uint64_t p2_rtout:1;
+		uint64_t p1_rtout:1;
+		uint64_t p0_rtout:1;
+		uint64_t i3_overf:1;
+		uint64_t i2_overf:1;
+		uint64_t i1_overf:1;
+		uint64_t i0_overf:1;
+		uint64_t i3_rtout:1;
+		uint64_t i2_rtout:1;
+		uint64_t i1_rtout:1;
+		uint64_t i0_rtout:1;
+		uint64_t po3_2sml:1;
+		uint64_t po2_2sml:1;
+		uint64_t po1_2sml:1;
+		uint64_t po0_2sml:1;
+		uint64_t pci_rsl:1;
+		uint64_t rml_wto:1;
+		uint64_t rml_rto:1;
+#else
+		uint64_t rml_rto:1;
+		uint64_t rml_wto:1;
+		uint64_t pci_rsl:1;
+		uint64_t po0_2sml:1;
+		uint64_t po1_2sml:1;
+		uint64_t po2_2sml:1;
+		uint64_t po3_2sml:1;
+		uint64_t i0_rtout:1;
+		uint64_t i1_rtout:1;
+		uint64_t i2_rtout:1;
+		uint64_t i3_rtout:1;
+		uint64_t i0_overf:1;
+		uint64_t i1_overf:1;
+		uint64_t i2_overf:1;
+		uint64_t i3_overf:1;
+		uint64_t p0_rtout:1;
+		uint64_t p1_rtout:1;
+		uint64_t p2_rtout:1;
+		uint64_t p3_rtout:1;
+		uint64_t p0_perr:1;
+		uint64_t p1_perr:1;
+		uint64_t p2_perr:1;
+		uint64_t p3_perr:1;
+		uint64_t g0_rtout:1;
+		uint64_t g1_rtout:1;
+		uint64_t g2_rtout:1;
+		uint64_t g3_rtout:1;
+		uint64_t p0_pperr:1;
+		uint64_t p1_pperr:1;
+		uint64_t p2_pperr:1;
+		uint64_t p3_pperr:1;
+		uint64_t p0_ptout:1;
+		uint64_t p1_ptout:1;
+		uint64_t p2_ptout:1;
+		uint64_t p3_ptout:1;
+		uint64_t i0_pperr:1;
+		uint64_t i1_pperr:1;
+		uint64_t i2_pperr:1;
+		uint64_t i3_pperr:1;
+		uint64_t win_rto:1;
+		uint64_t p_dperr:1;
+		uint64_t iobdma:1;
+		uint64_t reserved_42_63:22;
+#endif
+	} cn38xxp2;
+};
+
+union cvmx_npi_int_sum {
+	uint64_t u64;
+	struct cvmx_npi_int_sum_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_62_63:2;
+		uint64_t q1_a_f:1;
+		uint64_t q1_s_e:1;
+		uint64_t pdf_p_f:1;
+		uint64_t pdf_p_e:1;
+		uint64_t pcf_p_f:1;
+		uint64_t pcf_p_e:1;
+		uint64_t rdx_s_e:1;
+		uint64_t rwx_s_e:1;
+		uint64_t pnc_a_f:1;
+		uint64_t pnc_s_e:1;
+		uint64_t com_a_f:1;
+		uint64_t com_s_e:1;
+		uint64_t q3_a_f:1;
+		uint64_t q3_s_e:1;
+		uint64_t q2_a_f:1;
+		uint64_t q2_s_e:1;
+		uint64_t pcr_a_f:1;
+		uint64_t pcr_s_e:1;
+		uint64_t fcr_a_f:1;
+		uint64_t fcr_s_e:1;
+		uint64_t iobdma:1;
+		uint64_t p_dperr:1;
+		uint64_t win_rto:1;
+		uint64_t i3_pperr:1;
+		uint64_t i2_pperr:1;
+		uint64_t i1_pperr:1;
+		uint64_t i0_pperr:1;
+		uint64_t p3_ptout:1;
+		uint64_t p2_ptout:1;
+		uint64_t p1_ptout:1;
+		uint64_t p0_ptout:1;
+		uint64_t p3_pperr:1;
+		uint64_t p2_pperr:1;
+		uint64_t p1_pperr:1;
+		uint64_t p0_pperr:1;
+		uint64_t g3_rtout:1;
+		uint64_t g2_rtout:1;
+		uint64_t g1_rtout:1;
+		uint64_t g0_rtout:1;
+		uint64_t p3_perr:1;
+		uint64_t p2_perr:1;
+		uint64_t p1_perr:1;
+		uint64_t p0_perr:1;
+		uint64_t p3_rtout:1;
+		uint64_t p2_rtout:1;
+		uint64_t p1_rtout:1;
+		uint64_t p0_rtout:1;
+		uint64_t i3_overf:1;
+		uint64_t i2_overf:1;
+		uint64_t i1_overf:1;
+		uint64_t i0_overf:1;
+		uint64_t i3_rtout:1;
+		uint64_t i2_rtout:1;
+		uint64_t i1_rtout:1;
+		uint64_t i0_rtout:1;
+		uint64_t po3_2sml:1;
+		uint64_t po2_2sml:1;
+		uint64_t po1_2sml:1;
+		uint64_t po0_2sml:1;
+		uint64_t pci_rsl:1;
+		uint64_t rml_wto:1;
+		uint64_t rml_rto:1;
+#else
+		uint64_t rml_rto:1;
+		uint64_t rml_wto:1;
+		uint64_t pci_rsl:1;
+		uint64_t po0_2sml:1;
+		uint64_t po1_2sml:1;
+		uint64_t po2_2sml:1;
+		uint64_t po3_2sml:1;
+		uint64_t i0_rtout:1;
+		uint64_t i1_rtout:1;
+		uint64_t i2_rtout:1;
+		uint64_t i3_rtout:1;
+		uint64_t i0_overf:1;
+		uint64_t i1_overf:1;
+		uint64_t i2_overf:1;
+		uint64_t i3_overf:1;
+		uint64_t p0_rtout:1;
+		uint64_t p1_rtout:1;
+		uint64_t p2_rtout:1;
+		uint64_t p3_rtout:1;
+		uint64_t p0_perr:1;
+		uint64_t p1_perr:1;
+		uint64_t p2_perr:1;
+		uint64_t p3_perr:1;
+		uint64_t g0_rtout:1;
+		uint64_t g1_rtout:1;
+		uint64_t g2_rtout:1;
+		uint64_t g3_rtout:1;
+		uint64_t p0_pperr:1;
+		uint64_t p1_pperr:1;
+		uint64_t p2_pperr:1;
+		uint64_t p3_pperr:1;
+		uint64_t p0_ptout:1;
+		uint64_t p1_ptout:1;
+		uint64_t p2_ptout:1;
+		uint64_t p3_ptout:1;
+		uint64_t i0_pperr:1;
+		uint64_t i1_pperr:1;
+		uint64_t i2_pperr:1;
+		uint64_t i3_pperr:1;
+		uint64_t win_rto:1;
+		uint64_t p_dperr:1;
+		uint64_t iobdma:1;
+		uint64_t fcr_s_e:1;
+		uint64_t fcr_a_f:1;
+		uint64_t pcr_s_e:1;
+		uint64_t pcr_a_f:1;
+		uint64_t q2_s_e:1;
+		uint64_t q2_a_f:1;
+		uint64_t q3_s_e:1;
+		uint64_t q3_a_f:1;
+		uint64_t com_s_e:1;
+		uint64_t com_a_f:1;
+		uint64_t pnc_s_e:1;
+		uint64_t pnc_a_f:1;
+		uint64_t rwx_s_e:1;
+		uint64_t rdx_s_e:1;
+		uint64_t pcf_p_e:1;
+		uint64_t pcf_p_f:1;
+		uint64_t pdf_p_e:1;
+		uint64_t pdf_p_f:1;
+		uint64_t q1_s_e:1;
+		uint64_t q1_a_f:1;
+		uint64_t reserved_62_63:2;
+#endif
+	} s;
+	struct cvmx_npi_int_sum_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_62_63:2;
+		uint64_t q1_a_f:1;
+		uint64_t q1_s_e:1;
+		uint64_t pdf_p_f:1;
+		uint64_t pdf_p_e:1;
+		uint64_t pcf_p_f:1;
+		uint64_t pcf_p_e:1;
+		uint64_t rdx_s_e:1;
+		uint64_t rwx_s_e:1;
+		uint64_t pnc_a_f:1;
+		uint64_t pnc_s_e:1;
+		uint64_t com_a_f:1;
+		uint64_t com_s_e:1;
+		uint64_t q3_a_f:1;
+		uint64_t q3_s_e:1;
+		uint64_t q2_a_f:1;
+		uint64_t q2_s_e:1;
+		uint64_t pcr_a_f:1;
+		uint64_t pcr_s_e:1;
+		uint64_t fcr_a_f:1;
+		uint64_t fcr_s_e:1;
+		uint64_t iobdma:1;
+		uint64_t p_dperr:1;
+		uint64_t win_rto:1;
+		uint64_t reserved_36_38:3;
+		uint64_t i0_pperr:1;
+		uint64_t reserved_32_34:3;
+		uint64_t p0_ptout:1;
+		uint64_t reserved_28_30:3;
+		uint64_t p0_pperr:1;
+		uint64_t reserved_24_26:3;
+		uint64_t g0_rtout:1;
+		uint64_t reserved_20_22:3;
+		uint64_t p0_perr:1;
+		uint64_t reserved_16_18:3;
+		uint64_t p0_rtout:1;
+		uint64_t reserved_12_14:3;
+		uint64_t i0_overf:1;
+		uint64_t reserved_8_10:3;
+		uint64_t i0_rtout:1;
+		uint64_t reserved_4_6:3;
+		uint64_t po0_2sml:1;
+		uint64_t pci_rsl:1;
+		uint64_t rml_wto:1;
+		uint64_t rml_rto:1;
+#else
+		uint64_t rml_rto:1;
+		uint64_t rml_wto:1;
+		uint64_t pci_rsl:1;
+		uint64_t po0_2sml:1;
+		uint64_t reserved_4_6:3;
+		uint64_t i0_rtout:1;
+		uint64_t reserved_8_10:3;
+		uint64_t i0_overf:1;
+		uint64_t reserved_12_14:3;
+		uint64_t p0_rtout:1;
+		uint64_t reserved_16_18:3;
+		uint64_t p0_perr:1;
+		uint64_t reserved_20_22:3;
+		uint64_t g0_rtout:1;
+		uint64_t reserved_24_26:3;
+		uint64_t p0_pperr:1;
+		uint64_t reserved_28_30:3;
+		uint64_t p0_ptout:1;
+		uint64_t reserved_32_34:3;
+		uint64_t i0_pperr:1;
+		uint64_t reserved_36_38:3;
+		uint64_t win_rto:1;
+		uint64_t p_dperr:1;
+		uint64_t iobdma:1;
+		uint64_t fcr_s_e:1;
+		uint64_t fcr_a_f:1;
+		uint64_t pcr_s_e:1;
+		uint64_t pcr_a_f:1;
+		uint64_t q2_s_e:1;
+		uint64_t q2_a_f:1;
+		uint64_t q3_s_e:1;
+		uint64_t q3_a_f:1;
+		uint64_t com_s_e:1;
+		uint64_t com_a_f:1;
+		uint64_t pnc_s_e:1;
+		uint64_t pnc_a_f:1;
+		uint64_t rwx_s_e:1;
+		uint64_t rdx_s_e:1;
+		uint64_t pcf_p_e:1;
+		uint64_t pcf_p_f:1;
+		uint64_t pdf_p_e:1;
+		uint64_t pdf_p_f:1;
+		uint64_t q1_s_e:1;
+		uint64_t q1_a_f:1;
+		uint64_t reserved_62_63:2;
+#endif
+	} cn30xx;
+	struct cvmx_npi_int_sum_cn31xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_62_63:2;
+		uint64_t q1_a_f:1;
+		uint64_t q1_s_e:1;
+		uint64_t pdf_p_f:1;
+		uint64_t pdf_p_e:1;
+		uint64_t pcf_p_f:1;
+		uint64_t pcf_p_e:1;
+		uint64_t rdx_s_e:1;
+		uint64_t rwx_s_e:1;
+		uint64_t pnc_a_f:1;
+		uint64_t pnc_s_e:1;
+		uint64_t com_a_f:1;
+		uint64_t com_s_e:1;
+		uint64_t q3_a_f:1;
+		uint64_t q3_s_e:1;
+		uint64_t q2_a_f:1;
+		uint64_t q2_s_e:1;
+		uint64_t pcr_a_f:1;
+		uint64_t pcr_s_e:1;
+		uint64_t fcr_a_f:1;
+		uint64_t fcr_s_e:1;
+		uint64_t iobdma:1;
+		uint64_t p_dperr:1;
+		uint64_t win_rto:1;
+		uint64_t reserved_37_38:2;
+		uint64_t i1_pperr:1;
+		uint64_t i0_pperr:1;
+		uint64_t reserved_33_34:2;
+		uint64_t p1_ptout:1;
+		uint64_t p0_ptout:1;
+		uint64_t reserved_29_30:2;
+		uint64_t p1_pperr:1;
+		uint64_t p0_pperr:1;
+		uint64_t reserved_25_26:2;
+		uint64_t g1_rtout:1;
+		uint64_t g0_rtout:1;
+		uint64_t reserved_21_22:2;
+		uint64_t p1_perr:1;
+		uint64_t p0_perr:1;
+		uint64_t reserved_17_18:2;
+		uint64_t p1_rtout:1;
+		uint64_t p0_rtout:1;
+		uint64_t reserved_13_14:2;
+		uint64_t i1_overf:1;
+		uint64_t i0_overf:1;
+		uint64_t reserved_9_10:2;
+		uint64_t i1_rtout:1;
+		uint64_t i0_rtout:1;
+		uint64_t reserved_5_6:2;
+		uint64_t po1_2sml:1;
+		uint64_t po0_2sml:1;
+		uint64_t pci_rsl:1;
+		uint64_t rml_wto:1;
+		uint64_t rml_rto:1;
+#else
+		uint64_t rml_rto:1;
+		uint64_t rml_wto:1;
+		uint64_t pci_rsl:1;
+		uint64_t po0_2sml:1;
+		uint64_t po1_2sml:1;
+		uint64_t reserved_5_6:2;
+		uint64_t i0_rtout:1;
+		uint64_t i1_rtout:1;
+		uint64_t reserved_9_10:2;
+		uint64_t i0_overf:1;
+		uint64_t i1_overf:1;
+		uint64_t reserved_13_14:2;
+		uint64_t p0_rtout:1;
+		uint64_t p1_rtout:1;
+		uint64_t reserved_17_18:2;
+		uint64_t p0_perr:1;
+		uint64_t p1_perr:1;
+		uint64_t reserved_21_22:2;
+		uint64_t g0_rtout:1;
+		uint64_t g1_rtout:1;
+		uint64_t reserved_25_26:2;
+		uint64_t p0_pperr:1;
+		uint64_t p1_pperr:1;
+		uint64_t reserved_29_30:2;
+		uint64_t p0_ptout:1;
+		uint64_t p1_ptout:1;
+		uint64_t reserved_33_34:2;
+		uint64_t i0_pperr:1;
+		uint64_t i1_pperr:1;
+		uint64_t reserved_37_38:2;
+		uint64_t win_rto:1;
+		uint64_t p_dperr:1;
+		uint64_t iobdma:1;
+		uint64_t fcr_s_e:1;
+		uint64_t fcr_a_f:1;
+		uint64_t pcr_s_e:1;
+		uint64_t pcr_a_f:1;
+		uint64_t q2_s_e:1;
+		uint64_t q2_a_f:1;
+		uint64_t q3_s_e:1;
+		uint64_t q3_a_f:1;
+		uint64_t com_s_e:1;
+		uint64_t com_a_f:1;
+		uint64_t pnc_s_e:1;
+		uint64_t pnc_a_f:1;
+		uint64_t rwx_s_e:1;
+		uint64_t rdx_s_e:1;
+		uint64_t pcf_p_e:1;
+		uint64_t pcf_p_f:1;
+		uint64_t pdf_p_e:1;
+		uint64_t pdf_p_f:1;
+		uint64_t q1_s_e:1;
+		uint64_t q1_a_f:1;
+		uint64_t reserved_62_63:2;
+#endif
+	} cn31xx;
+	struct cvmx_npi_int_sum_cn38xxp2 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_42_63:22;
+		uint64_t iobdma:1;
+		uint64_t p_dperr:1;
+		uint64_t win_rto:1;
+		uint64_t i3_pperr:1;
+		uint64_t i2_pperr:1;
+		uint64_t i1_pperr:1;
+		uint64_t i0_pperr:1;
+		uint64_t p3_ptout:1;
+		uint64_t p2_ptout:1;
+		uint64_t p1_ptout:1;
+		uint64_t p0_ptout:1;
+		uint64_t p3_pperr:1;
+		uint64_t p2_pperr:1;
+		uint64_t p1_pperr:1;
+		uint64_t p0_pperr:1;
+		uint64_t g3_rtout:1;
+		uint64_t g2_rtout:1;
+		uint64_t g1_rtout:1;
+		uint64_t g0_rtout:1;
+		uint64_t p3_perr:1;
+		uint64_t p2_perr:1;
+		uint64_t p1_perr:1;
+		uint64_t p0_perr:1;
+		uint64_t p3_rtout:1;
+		uint64_t p2_rtout:1;
+		uint64_t p1_rtout:1;
+		uint64_t p0_rtout:1;
+		uint64_t i3_overf:1;
+		uint64_t i2_overf:1;
+		uint64_t i1_overf:1;
+		uint64_t i0_overf:1;
+		uint64_t i3_rtout:1;
+		uint64_t i2_rtout:1;
+		uint64_t i1_rtout:1;
+		uint64_t i0_rtout:1;
+		uint64_t po3_2sml:1;
+		uint64_t po2_2sml:1;
+		uint64_t po1_2sml:1;
+		uint64_t po0_2sml:1;
+		uint64_t pci_rsl:1;
+		uint64_t rml_wto:1;
+		uint64_t rml_rto:1;
+#else
+		uint64_t rml_rto:1;
+		uint64_t rml_wto:1;
+		uint64_t pci_rsl:1;
+		uint64_t po0_2sml:1;
+		uint64_t po1_2sml:1;
+		uint64_t po2_2sml:1;
+		uint64_t po3_2sml:1;
+		uint64_t i0_rtout:1;
+		uint64_t i1_rtout:1;
+		uint64_t i2_rtout:1;
+		uint64_t i3_rtout:1;
+		uint64_t i0_overf:1;
+		uint64_t i1_overf:1;
+		uint64_t i2_overf:1;
+		uint64_t i3_overf:1;
+		uint64_t p0_rtout:1;
+		uint64_t p1_rtout:1;
+		uint64_t p2_rtout:1;
+		uint64_t p3_rtout:1;
+		uint64_t p0_perr:1;
+		uint64_t p1_perr:1;
+		uint64_t p2_perr:1;
+		uint64_t p3_perr:1;
+		uint64_t g0_rtout:1;
+		uint64_t g1_rtout:1;
+		uint64_t g2_rtout:1;
+		uint64_t g3_rtout:1;
+		uint64_t p0_pperr:1;
+		uint64_t p1_pperr:1;
+		uint64_t p2_pperr:1;
+		uint64_t p3_pperr:1;
+		uint64_t p0_ptout:1;
+		uint64_t p1_ptout:1;
+		uint64_t p2_ptout:1;
+		uint64_t p3_ptout:1;
+		uint64_t i0_pperr:1;
+		uint64_t i1_pperr:1;
+		uint64_t i2_pperr:1;
+		uint64_t i3_pperr:1;
+		uint64_t win_rto:1;
+		uint64_t p_dperr:1;
+		uint64_t iobdma:1;
+		uint64_t reserved_42_63:22;
+#endif
+	} cn38xxp2;
+};
+
+union cvmx_npi_lowp_dbell {
+	uint64_t u64;
+	struct cvmx_npi_lowp_dbell_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t dbell:16;
+#else
+		uint64_t dbell:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_npi_lowp_ibuff_saddr {
+	uint64_t u64;
+	struct cvmx_npi_lowp_ibuff_saddr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_36_63:28;
+		uint64_t saddr:36;
+#else
+		uint64_t saddr:36;
+		uint64_t reserved_36_63:28;
+#endif
+	} s;
+};
+
+union cvmx_npi_mem_access_subidx {
+	uint64_t u64;
+	struct cvmx_npi_mem_access_subidx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_38_63:26;
+		uint64_t shortl:1;
+		uint64_t nmerge:1;
+		uint64_t esr:2;
+		uint64_t esw:2;
+		uint64_t nsr:1;
+		uint64_t nsw:1;
+		uint64_t ror:1;
+		uint64_t row:1;
+		uint64_t ba:28;
+#else
+		uint64_t ba:28;
+		uint64_t row:1;
+		uint64_t ror:1;
+		uint64_t nsw:1;
+		uint64_t nsr:1;
+		uint64_t esw:2;
+		uint64_t esr:2;
+		uint64_t nmerge:1;
+		uint64_t shortl:1;
+		uint64_t reserved_38_63:26;
+#endif
+	} s;
+	struct cvmx_npi_mem_access_subidx_cn31xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_36_63:28;
+		uint64_t esr:2;
+		uint64_t esw:2;
+		uint64_t nsr:1;
+		uint64_t nsw:1;
+		uint64_t ror:1;
+		uint64_t row:1;
+		uint64_t ba:28;
+#else
+		uint64_t ba:28;
+		uint64_t row:1;
+		uint64_t ror:1;
+		uint64_t nsw:1;
+		uint64_t nsr:1;
+		uint64_t esw:2;
+		uint64_t esr:2;
+		uint64_t reserved_36_63:28;
+#endif
+	} cn31xx;
+};
+
+union cvmx_npi_msi_rcv {
+	uint64_t u64;
+	struct cvmx_npi_msi_rcv_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t int_vec:64;
+#else
+		uint64_t int_vec:64;
+#endif
+	} s;
+};
+
+union cvmx_npi_num_desc_outputx {
+	uint64_t u64;
+	struct cvmx_npi_num_desc_outputx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t size:32;
+#else
+		uint64_t size:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_npi_output_control {
+	uint64_t u64;
+	struct cvmx_npi_output_control_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_49_63:15;
+		uint64_t pkt_rr:1;
+		uint64_t p3_bmode:1;
+		uint64_t p2_bmode:1;
+		uint64_t p1_bmode:1;
+		uint64_t p0_bmode:1;
+		uint64_t o3_es:2;
+		uint64_t o3_ns:1;
+		uint64_t o3_ro:1;
+		uint64_t o2_es:2;
+		uint64_t o2_ns:1;
+		uint64_t o2_ro:1;
+		uint64_t o1_es:2;
+		uint64_t o1_ns:1;
+		uint64_t o1_ro:1;
+		uint64_t o0_es:2;
+		uint64_t o0_ns:1;
+		uint64_t o0_ro:1;
+		uint64_t o3_csrm:1;
+		uint64_t o2_csrm:1;
+		uint64_t o1_csrm:1;
+		uint64_t o0_csrm:1;
+		uint64_t reserved_20_23:4;
+		uint64_t iptr_o3:1;
+		uint64_t iptr_o2:1;
+		uint64_t iptr_o1:1;
+		uint64_t iptr_o0:1;
+		uint64_t esr_sl3:2;
+		uint64_t nsr_sl3:1;
+		uint64_t ror_sl3:1;
+		uint64_t esr_sl2:2;
+		uint64_t nsr_sl2:1;
+		uint64_t ror_sl2:1;
+		uint64_t esr_sl1:2;
+		uint64_t nsr_sl1:1;
+		uint64_t ror_sl1:1;
+		uint64_t esr_sl0:2;
+		uint64_t nsr_sl0:1;
+		uint64_t ror_sl0:1;
+#else
+		uint64_t ror_sl0:1;
+		uint64_t nsr_sl0:1;
+		uint64_t esr_sl0:2;
+		uint64_t ror_sl1:1;
+		uint64_t nsr_sl1:1;
+		uint64_t esr_sl1:2;
+		uint64_t ror_sl2:1;
+		uint64_t nsr_sl2:1;
+		uint64_t esr_sl2:2;
+		uint64_t ror_sl3:1;
+		uint64_t nsr_sl3:1;
+		uint64_t esr_sl3:2;
+		uint64_t iptr_o0:1;
+		uint64_t iptr_o1:1;
+		uint64_t iptr_o2:1;
+		uint64_t iptr_o3:1;
+		uint64_t reserved_20_23:4;
+		uint64_t o0_csrm:1;
+		uint64_t o1_csrm:1;
+		uint64_t o2_csrm:1;
+		uint64_t o3_csrm:1;
+		uint64_t o0_ro:1;
+		uint64_t o0_ns:1;
+		uint64_t o0_es:2;
+		uint64_t o1_ro:1;
+		uint64_t o1_ns:1;
+		uint64_t o1_es:2;
+		uint64_t o2_ro:1;
+		uint64_t o2_ns:1;
+		uint64_t o2_es:2;
+		uint64_t o3_ro:1;
+		uint64_t o3_ns:1;
+		uint64_t o3_es:2;
+		uint64_t p0_bmode:1;
+		uint64_t p1_bmode:1;
+		uint64_t p2_bmode:1;
+		uint64_t p3_bmode:1;
+		uint64_t pkt_rr:1;
+		uint64_t reserved_49_63:15;
+#endif
+	} s;
+	struct cvmx_npi_output_control_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_45_63:19;
+		uint64_t p0_bmode:1;
+		uint64_t reserved_32_43:12;
+		uint64_t o0_es:2;
+		uint64_t o0_ns:1;
+		uint64_t o0_ro:1;
+		uint64_t reserved_25_27:3;
+		uint64_t o0_csrm:1;
+		uint64_t reserved_17_23:7;
+		uint64_t iptr_o0:1;
+		uint64_t reserved_4_15:12;
+		uint64_t esr_sl0:2;
+		uint64_t nsr_sl0:1;
+		uint64_t ror_sl0:1;
+#else
+		uint64_t ror_sl0:1;
+		uint64_t nsr_sl0:1;
+		uint64_t esr_sl0:2;
+		uint64_t reserved_4_15:12;
+		uint64_t iptr_o0:1;
+		uint64_t reserved_17_23:7;
+		uint64_t o0_csrm:1;
+		uint64_t reserved_25_27:3;
+		uint64_t o0_ro:1;
+		uint64_t o0_ns:1;
+		uint64_t o0_es:2;
+		uint64_t reserved_32_43:12;
+		uint64_t p0_bmode:1;
+		uint64_t reserved_45_63:19;
+#endif
+	} cn30xx;
+	struct cvmx_npi_output_control_cn31xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_46_63:18;
+		uint64_t p1_bmode:1;
+		uint64_t p0_bmode:1;
+		uint64_t reserved_36_43:8;
+		uint64_t o1_es:2;
+		uint64_t o1_ns:1;
+		uint64_t o1_ro:1;
+		uint64_t o0_es:2;
+		uint64_t o0_ns:1;
+		uint64_t o0_ro:1;
+		uint64_t reserved_26_27:2;
+		uint64_t o1_csrm:1;
+		uint64_t o0_csrm:1;
+		uint64_t reserved_18_23:6;
+		uint64_t iptr_o1:1;
+		uint64_t iptr_o0:1;
+		uint64_t reserved_8_15:8;
+		uint64_t esr_sl1:2;
+		uint64_t nsr_sl1:1;
+		uint64_t ror_sl1:1;
+		uint64_t esr_sl0:2;
+		uint64_t nsr_sl0:1;
+		uint64_t ror_sl0:1;
+#else
+		uint64_t ror_sl0:1;
+		uint64_t nsr_sl0:1;
+		uint64_t esr_sl0:2;
+		uint64_t ror_sl1:1;
+		uint64_t nsr_sl1:1;
+		uint64_t esr_sl1:2;
+		uint64_t reserved_8_15:8;
+		uint64_t iptr_o0:1;
+		uint64_t iptr_o1:1;
+		uint64_t reserved_18_23:6;
+		uint64_t o0_csrm:1;
+		uint64_t o1_csrm:1;
+		uint64_t reserved_26_27:2;
+		uint64_t o0_ro:1;
+		uint64_t o0_ns:1;
+		uint64_t o0_es:2;
+		uint64_t o1_ro:1;
+		uint64_t o1_ns:1;
+		uint64_t o1_es:2;
+		uint64_t reserved_36_43:8;
+		uint64_t p0_bmode:1;
+		uint64_t p1_bmode:1;
+		uint64_t reserved_46_63:18;
+#endif
+	} cn31xx;
+	struct cvmx_npi_output_control_cn38xxp2 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t p3_bmode:1;
+		uint64_t p2_bmode:1;
+		uint64_t p1_bmode:1;
+		uint64_t p0_bmode:1;
+		uint64_t o3_es:2;
+		uint64_t o3_ns:1;
+		uint64_t o3_ro:1;
+		uint64_t o2_es:2;
+		uint64_t o2_ns:1;
+		uint64_t o2_ro:1;
+		uint64_t o1_es:2;
+		uint64_t o1_ns:1;
+		uint64_t o1_ro:1;
+		uint64_t o0_es:2;
+		uint64_t o0_ns:1;
+		uint64_t o0_ro:1;
+		uint64_t o3_csrm:1;
+		uint64_t o2_csrm:1;
+		uint64_t o1_csrm:1;
+		uint64_t o0_csrm:1;
+		uint64_t reserved_20_23:4;
+		uint64_t iptr_o3:1;
+		uint64_t iptr_o2:1;
+		uint64_t iptr_o1:1;
+		uint64_t iptr_o0:1;
+		uint64_t esr_sl3:2;
+		uint64_t nsr_sl3:1;
+		uint64_t ror_sl3:1;
+		uint64_t esr_sl2:2;
+		uint64_t nsr_sl2:1;
+		uint64_t ror_sl2:1;
+		uint64_t esr_sl1:2;
+		uint64_t nsr_sl1:1;
+		uint64_t ror_sl1:1;
+		uint64_t esr_sl0:2;
+		uint64_t nsr_sl0:1;
+		uint64_t ror_sl0:1;
+#else
+		uint64_t ror_sl0:1;
+		uint64_t nsr_sl0:1;
+		uint64_t esr_sl0:2;
+		uint64_t ror_sl1:1;
+		uint64_t nsr_sl1:1;
+		uint64_t esr_sl1:2;
+		uint64_t ror_sl2:1;
+		uint64_t nsr_sl2:1;
+		uint64_t esr_sl2:2;
+		uint64_t ror_sl3:1;
+		uint64_t nsr_sl3:1;
+		uint64_t esr_sl3:2;
+		uint64_t iptr_o0:1;
+		uint64_t iptr_o1:1;
+		uint64_t iptr_o2:1;
+		uint64_t iptr_o3:1;
+		uint64_t reserved_20_23:4;
+		uint64_t o0_csrm:1;
+		uint64_t o1_csrm:1;
+		uint64_t o2_csrm:1;
+		uint64_t o3_csrm:1;
+		uint64_t o0_ro:1;
+		uint64_t o0_ns:1;
+		uint64_t o0_es:2;
+		uint64_t o1_ro:1;
+		uint64_t o1_ns:1;
+		uint64_t o1_es:2;
+		uint64_t o2_ro:1;
+		uint64_t o2_ns:1;
+		uint64_t o2_es:2;
+		uint64_t o3_ro:1;
+		uint64_t o3_ns:1;
+		uint64_t o3_es:2;
+		uint64_t p0_bmode:1;
+		uint64_t p1_bmode:1;
+		uint64_t p2_bmode:1;
+		uint64_t p3_bmode:1;
+		uint64_t reserved_48_63:16;
+#endif
+	} cn38xxp2;
+	struct cvmx_npi_output_control_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_49_63:15;
+		uint64_t pkt_rr:1;
+		uint64_t reserved_46_47:2;
+		uint64_t p1_bmode:1;
+		uint64_t p0_bmode:1;
+		uint64_t reserved_36_43:8;
+		uint64_t o1_es:2;
+		uint64_t o1_ns:1;
+		uint64_t o1_ro:1;
+		uint64_t o0_es:2;
+		uint64_t o0_ns:1;
+		uint64_t o0_ro:1;
+		uint64_t reserved_26_27:2;
+		uint64_t o1_csrm:1;
+		uint64_t o0_csrm:1;
+		uint64_t reserved_18_23:6;
+		uint64_t iptr_o1:1;
+		uint64_t iptr_o0:1;
+		uint64_t reserved_8_15:8;
+		uint64_t esr_sl1:2;
+		uint64_t nsr_sl1:1;
+		uint64_t ror_sl1:1;
+		uint64_t esr_sl0:2;
+		uint64_t nsr_sl0:1;
+		uint64_t ror_sl0:1;
+#else
+		uint64_t ror_sl0:1;
+		uint64_t nsr_sl0:1;
+		uint64_t esr_sl0:2;
+		uint64_t ror_sl1:1;
+		uint64_t nsr_sl1:1;
+		uint64_t esr_sl1:2;
+		uint64_t reserved_8_15:8;
+		uint64_t iptr_o0:1;
+		uint64_t iptr_o1:1;
+		uint64_t reserved_18_23:6;
+		uint64_t o0_csrm:1;
+		uint64_t o1_csrm:1;
+		uint64_t reserved_26_27:2;
+		uint64_t o0_ro:1;
+		uint64_t o0_ns:1;
+		uint64_t o0_es:2;
+		uint64_t o1_ro:1;
+		uint64_t o1_ns:1;
+		uint64_t o1_es:2;
+		uint64_t reserved_36_43:8;
+		uint64_t p0_bmode:1;
+		uint64_t p1_bmode:1;
+		uint64_t reserved_46_47:2;
+		uint64_t pkt_rr:1;
+		uint64_t reserved_49_63:15;
+#endif
+	} cn50xx;
+};
+
+union cvmx_npi_px_dbpair_addr {
+	uint64_t u64;
+	struct cvmx_npi_px_dbpair_addr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_63_63:1;
+		uint64_t state:2;
+		uint64_t naddr:61;
+#else
+		uint64_t naddr:61;
+		uint64_t state:2;
+		uint64_t reserved_63_63:1;
+#endif
+	} s;
+};
+
+union cvmx_npi_px_instr_addr {
+	uint64_t u64;
+	struct cvmx_npi_px_instr_addr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t state:3;
+		uint64_t naddr:61;
+#else
+		uint64_t naddr:61;
+		uint64_t state:3;
+#endif
+	} s;
+};
+
+union cvmx_npi_px_instr_cnts {
+	uint64_t u64;
+	struct cvmx_npi_px_instr_cnts_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_38_63:26;
+		uint64_t fcnt:6;
+		uint64_t avail:32;
+#else
+		uint64_t avail:32;
+		uint64_t fcnt:6;
+		uint64_t reserved_38_63:26;
+#endif
+	} s;
+};
+
+union cvmx_npi_px_pair_cnts {
+	uint64_t u64;
+	struct cvmx_npi_px_pair_cnts_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_37_63:27;
+		uint64_t fcnt:5;
+		uint64_t avail:32;
+#else
+		uint64_t avail:32;
+		uint64_t fcnt:5;
+		uint64_t reserved_37_63:27;
+#endif
+	} s;
+};
+
+union cvmx_npi_pci_burst_size {
+	uint64_t u64;
+	struct cvmx_npi_pci_burst_size_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_14_63:50;
+		uint64_t wr_brst:7;
+		uint64_t rd_brst:7;
+#else
+		uint64_t rd_brst:7;
+		uint64_t wr_brst:7;
+		uint64_t reserved_14_63:50;
+#endif
+	} s;
+};
+
+union cvmx_npi_pci_int_arb_cfg {
+	uint64_t u64;
+	struct cvmx_npi_pci_int_arb_cfg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_13_63:51;
+		uint64_t hostmode:1;
+		uint64_t pci_ovr:4;
+		uint64_t reserved_5_7:3;
+		uint64_t en:1;
+		uint64_t park_mod:1;
+		uint64_t park_dev:3;
+#else
+		uint64_t park_dev:3;
+		uint64_t park_mod:1;
+		uint64_t en:1;
+		uint64_t reserved_5_7:3;
+		uint64_t pci_ovr:4;
+		uint64_t hostmode:1;
+		uint64_t reserved_13_63:51;
+#endif
+	} s;
+	struct cvmx_npi_pci_int_arb_cfg_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_5_63:59;
+		uint64_t en:1;
+		uint64_t park_mod:1;
+		uint64_t park_dev:3;
+#else
+		uint64_t park_dev:3;
+		uint64_t park_mod:1;
+		uint64_t en:1;
+		uint64_t reserved_5_63:59;
+#endif
+	} cn30xx;
+};
+
+union cvmx_npi_pci_read_cmd {
+	uint64_t u64;
+	struct cvmx_npi_pci_read_cmd_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_11_63:53;
+		uint64_t cmd_size:11;
+#else
+		uint64_t cmd_size:11;
+		uint64_t reserved_11_63:53;
+#endif
+	} s;
+};
+
+union cvmx_npi_port32_instr_hdr {
+	uint64_t u64;
+	struct cvmx_npi_port32_instr_hdr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_44_63:20;
+		uint64_t pbp:1;
+		uint64_t rsv_f:5;
+		uint64_t rparmode:2;
+		uint64_t rsv_e:1;
+		uint64_t rskp_len:7;
+		uint64_t rsv_d:6;
+		uint64_t use_ihdr:1;
+		uint64_t rsv_c:5;
+		uint64_t par_mode:2;
+		uint64_t rsv_b:1;
+		uint64_t skp_len:7;
+		uint64_t rsv_a:6;
+#else
+		uint64_t rsv_a:6;
+		uint64_t skp_len:7;
+		uint64_t rsv_b:1;
+		uint64_t par_mode:2;
+		uint64_t rsv_c:5;
+		uint64_t use_ihdr:1;
+		uint64_t rsv_d:6;
+		uint64_t rskp_len:7;
+		uint64_t rsv_e:1;
+		uint64_t rparmode:2;
+		uint64_t rsv_f:5;
+		uint64_t pbp:1;
+		uint64_t reserved_44_63:20;
+#endif
+	} s;
+};
+
+union cvmx_npi_port33_instr_hdr {
+	uint64_t u64;
+	struct cvmx_npi_port33_instr_hdr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_44_63:20;
+		uint64_t pbp:1;
+		uint64_t rsv_f:5;
+		uint64_t rparmode:2;
+		uint64_t rsv_e:1;
+		uint64_t rskp_len:7;
+		uint64_t rsv_d:6;
+		uint64_t use_ihdr:1;
+		uint64_t rsv_c:5;
+		uint64_t par_mode:2;
+		uint64_t rsv_b:1;
+		uint64_t skp_len:7;
+		uint64_t rsv_a:6;
+#else
+		uint64_t rsv_a:6;
+		uint64_t skp_len:7;
+		uint64_t rsv_b:1;
+		uint64_t par_mode:2;
+		uint64_t rsv_c:5;
+		uint64_t use_ihdr:1;
+		uint64_t rsv_d:6;
+		uint64_t rskp_len:7;
+		uint64_t rsv_e:1;
+		uint64_t rparmode:2;
+		uint64_t rsv_f:5;
+		uint64_t pbp:1;
+		uint64_t reserved_44_63:20;
+#endif
+	} s;
+};
+
+union cvmx_npi_port34_instr_hdr {
+	uint64_t u64;
+	struct cvmx_npi_port34_instr_hdr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_44_63:20;
+		uint64_t pbp:1;
+		uint64_t rsv_f:5;
+		uint64_t rparmode:2;
+		uint64_t rsv_e:1;
+		uint64_t rskp_len:7;
+		uint64_t rsv_d:6;
+		uint64_t use_ihdr:1;
+		uint64_t rsv_c:5;
+		uint64_t par_mode:2;
+		uint64_t rsv_b:1;
+		uint64_t skp_len:7;
+		uint64_t rsv_a:6;
+#else
+		uint64_t rsv_a:6;
+		uint64_t skp_len:7;
+		uint64_t rsv_b:1;
+		uint64_t par_mode:2;
+		uint64_t rsv_c:5;
+		uint64_t use_ihdr:1;
+		uint64_t rsv_d:6;
+		uint64_t rskp_len:7;
+		uint64_t rsv_e:1;
+		uint64_t rparmode:2;
+		uint64_t rsv_f:5;
+		uint64_t pbp:1;
+		uint64_t reserved_44_63:20;
+#endif
+	} s;
+};
+
+union cvmx_npi_port35_instr_hdr {
+	uint64_t u64;
+	struct cvmx_npi_port35_instr_hdr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_44_63:20;
+		uint64_t pbp:1;
+		uint64_t rsv_f:5;
+		uint64_t rparmode:2;
+		uint64_t rsv_e:1;
+		uint64_t rskp_len:7;
+		uint64_t rsv_d:6;
+		uint64_t use_ihdr:1;
+		uint64_t rsv_c:5;
+		uint64_t par_mode:2;
+		uint64_t rsv_b:1;
+		uint64_t skp_len:7;
+		uint64_t rsv_a:6;
+#else
+		uint64_t rsv_a:6;
+		uint64_t skp_len:7;
+		uint64_t rsv_b:1;
+		uint64_t par_mode:2;
+		uint64_t rsv_c:5;
+		uint64_t use_ihdr:1;
+		uint64_t rsv_d:6;
+		uint64_t rskp_len:7;
+		uint64_t rsv_e:1;
+		uint64_t rparmode:2;
+		uint64_t rsv_f:5;
+		uint64_t pbp:1;
+		uint64_t reserved_44_63:20;
+#endif
+	} s;
+};
+
+union cvmx_npi_port_bp_control {
+	uint64_t u64;
+	struct cvmx_npi_port_bp_control_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t bp_on:4;
+		uint64_t enb:4;
+#else
+		uint64_t enb:4;
+		uint64_t bp_on:4;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_npi_rsl_int_blocks {
+	uint64_t u64;
+	struct cvmx_npi_rsl_int_blocks_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t rint_31:1;
+		uint64_t iob:1;
+		uint64_t reserved_28_29:2;
+		uint64_t rint_27:1;
+		uint64_t rint_26:1;
+		uint64_t rint_25:1;
+		uint64_t rint_24:1;
+		uint64_t asx1:1;
+		uint64_t asx0:1;
+		uint64_t rint_21:1;
+		uint64_t pip:1;
+		uint64_t spx1:1;
+		uint64_t spx0:1;
+		uint64_t lmc:1;
+		uint64_t l2c:1;
+		uint64_t rint_15:1;
+		uint64_t reserved_13_14:2;
+		uint64_t pow:1;
+		uint64_t tim:1;
+		uint64_t pko:1;
+		uint64_t ipd:1;
+		uint64_t rint_8:1;
+		uint64_t zip:1;
+		uint64_t dfa:1;
+		uint64_t fpa:1;
+		uint64_t key:1;
+		uint64_t npi:1;
+		uint64_t gmx1:1;
+		uint64_t gmx0:1;
+		uint64_t mio:1;
+#else
+		uint64_t mio:1;
+		uint64_t gmx0:1;
+		uint64_t gmx1:1;
+		uint64_t npi:1;
+		uint64_t key:1;
+		uint64_t fpa:1;
+		uint64_t dfa:1;
+		uint64_t zip:1;
+		uint64_t rint_8:1;
+		uint64_t ipd:1;
+		uint64_t pko:1;
+		uint64_t tim:1;
+		uint64_t pow:1;
+		uint64_t reserved_13_14:2;
+		uint64_t rint_15:1;
+		uint64_t l2c:1;
+		uint64_t lmc:1;
+		uint64_t spx0:1;
+		uint64_t spx1:1;
+		uint64_t pip:1;
+		uint64_t rint_21:1;
+		uint64_t asx0:1;
+		uint64_t asx1:1;
+		uint64_t rint_24:1;
+		uint64_t rint_25:1;
+		uint64_t rint_26:1;
+		uint64_t rint_27:1;
+		uint64_t reserved_28_29:2;
+		uint64_t iob:1;
+		uint64_t rint_31:1;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+	struct cvmx_npi_rsl_int_blocks_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t rint_31:1;
+		uint64_t iob:1;
+		uint64_t rint_29:1;
+		uint64_t rint_28:1;
+		uint64_t rint_27:1;
+		uint64_t rint_26:1;
+		uint64_t rint_25:1;
+		uint64_t rint_24:1;
+		uint64_t asx1:1;
+		uint64_t asx0:1;
+		uint64_t rint_21:1;
+		uint64_t pip:1;
+		uint64_t spx1:1;
+		uint64_t spx0:1;
+		uint64_t lmc:1;
+		uint64_t l2c:1;
+		uint64_t rint_15:1;
+		uint64_t rint_14:1;
+		uint64_t usb:1;
+		uint64_t pow:1;
+		uint64_t tim:1;
+		uint64_t pko:1;
+		uint64_t ipd:1;
+		uint64_t rint_8:1;
+		uint64_t zip:1;
+		uint64_t dfa:1;
+		uint64_t fpa:1;
+		uint64_t key:1;
+		uint64_t npi:1;
+		uint64_t gmx1:1;
+		uint64_t gmx0:1;
+		uint64_t mio:1;
+#else
+		uint64_t mio:1;
+		uint64_t gmx0:1;
+		uint64_t gmx1:1;
+		uint64_t npi:1;
+		uint64_t key:1;
+		uint64_t fpa:1;
+		uint64_t dfa:1;
+		uint64_t zip:1;
+		uint64_t rint_8:1;
+		uint64_t ipd:1;
+		uint64_t pko:1;
+		uint64_t tim:1;
+		uint64_t pow:1;
+		uint64_t usb:1;
+		uint64_t rint_14:1;
+		uint64_t rint_15:1;
+		uint64_t l2c:1;
+		uint64_t lmc:1;
+		uint64_t spx0:1;
+		uint64_t spx1:1;
+		uint64_t pip:1;
+		uint64_t rint_21:1;
+		uint64_t asx0:1;
+		uint64_t asx1:1;
+		uint64_t rint_24:1;
+		uint64_t rint_25:1;
+		uint64_t rint_26:1;
+		uint64_t rint_27:1;
+		uint64_t rint_28:1;
+		uint64_t rint_29:1;
+		uint64_t iob:1;
+		uint64_t rint_31:1;
+		uint64_t reserved_32_63:32;
+#endif
+	} cn30xx;
+	struct cvmx_npi_rsl_int_blocks_cn38xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t rint_31:1;
+		uint64_t iob:1;
+		uint64_t rint_29:1;
+		uint64_t rint_28:1;
+		uint64_t rint_27:1;
+		uint64_t rint_26:1;
+		uint64_t rint_25:1;
+		uint64_t rint_24:1;
+		uint64_t asx1:1;
+		uint64_t asx0:1;
+		uint64_t rint_21:1;
+		uint64_t pip:1;
+		uint64_t spx1:1;
+		uint64_t spx0:1;
+		uint64_t lmc:1;
+		uint64_t l2c:1;
+		uint64_t rint_15:1;
+		uint64_t rint_14:1;
+		uint64_t rint_13:1;
+		uint64_t pow:1;
+		uint64_t tim:1;
+		uint64_t pko:1;
+		uint64_t ipd:1;
+		uint64_t rint_8:1;
+		uint64_t zip:1;
+		uint64_t dfa:1;
+		uint64_t fpa:1;
+		uint64_t key:1;
+		uint64_t npi:1;
+		uint64_t gmx1:1;
+		uint64_t gmx0:1;
+		uint64_t mio:1;
+#else
+		uint64_t mio:1;
+		uint64_t gmx0:1;
+		uint64_t gmx1:1;
+		uint64_t npi:1;
+		uint64_t key:1;
+		uint64_t fpa:1;
+		uint64_t dfa:1;
+		uint64_t zip:1;
+		uint64_t rint_8:1;
+		uint64_t ipd:1;
+		uint64_t pko:1;
+		uint64_t tim:1;
+		uint64_t pow:1;
+		uint64_t rint_13:1;
+		uint64_t rint_14:1;
+		uint64_t rint_15:1;
+		uint64_t l2c:1;
+		uint64_t lmc:1;
+		uint64_t spx0:1;
+		uint64_t spx1:1;
+		uint64_t pip:1;
+		uint64_t rint_21:1;
+		uint64_t asx0:1;
+		uint64_t asx1:1;
+		uint64_t rint_24:1;
+		uint64_t rint_25:1;
+		uint64_t rint_26:1;
+		uint64_t rint_27:1;
+		uint64_t rint_28:1;
+		uint64_t rint_29:1;
+		uint64_t iob:1;
+		uint64_t rint_31:1;
+		uint64_t reserved_32_63:32;
+#endif
+	} cn38xx;
+	struct cvmx_npi_rsl_int_blocks_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_31_63:33;
+		uint64_t iob:1;
+		uint64_t lmc1:1;
+		uint64_t agl:1;
+		uint64_t reserved_24_27:4;
+		uint64_t asx1:1;
+		uint64_t asx0:1;
+		uint64_t reserved_21_21:1;
+		uint64_t pip:1;
+		uint64_t spx1:1;
+		uint64_t spx0:1;
+		uint64_t lmc:1;
+		uint64_t l2c:1;
+		uint64_t reserved_15_15:1;
+		uint64_t rad:1;
+		uint64_t usb:1;
+		uint64_t pow:1;
+		uint64_t tim:1;
+		uint64_t pko:1;
+		uint64_t ipd:1;
+		uint64_t reserved_8_8:1;
+		uint64_t zip:1;
+		uint64_t dfa:1;
+		uint64_t fpa:1;
+		uint64_t key:1;
+		uint64_t npi:1;
+		uint64_t gmx1:1;
+		uint64_t gmx0:1;
+		uint64_t mio:1;
+#else
+		uint64_t mio:1;
+		uint64_t gmx0:1;
+		uint64_t gmx1:1;
+		uint64_t npi:1;
+		uint64_t key:1;
+		uint64_t fpa:1;
+		uint64_t dfa:1;
+		uint64_t zip:1;
+		uint64_t reserved_8_8:1;
+		uint64_t ipd:1;
+		uint64_t pko:1;
+		uint64_t tim:1;
+		uint64_t pow:1;
+		uint64_t usb:1;
+		uint64_t rad:1;
+		uint64_t reserved_15_15:1;
+		uint64_t l2c:1;
+		uint64_t lmc:1;
+		uint64_t spx0:1;
+		uint64_t spx1:1;
+		uint64_t pip:1;
+		uint64_t reserved_21_21:1;
+		uint64_t asx0:1;
+		uint64_t asx1:1;
+		uint64_t reserved_24_27:4;
+		uint64_t agl:1;
+		uint64_t lmc1:1;
+		uint64_t iob:1;
+		uint64_t reserved_31_63:33;
+#endif
+	} cn50xx;
+};
+
+union cvmx_npi_size_inputx {
+	uint64_t u64;
+	struct cvmx_npi_size_inputx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t size:32;
+#else
+		uint64_t size:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_npi_win_read_to {
+	uint64_t u64;
+	struct cvmx_npi_win_read_to_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t time:32;
+#else
+		uint64_t time:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-packet.h b/arch/mips/include/asm/octeon/cvmx-packet.h
new file mode 100644
index 000000000..895e93d68
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-packet.h
@@ -0,0 +1,69 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ * Packet buffer defines.
+ */
+
+#ifndef __CVMX_PACKET_H__
+#define __CVMX_PACKET_H__
+
+/**
+ * This structure defines a buffer pointer on Octeon
+ */
+union cvmx_buf_ptr {
+	void *ptr;
+	uint64_t u64;
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		/* if set, invert the "free" pick of the overall
+		 * packet. HW always sets this bit to 0 on inbound
+		 * packet */
+		uint64_t i:1;
+
+		/* Indicates the amount to back up to get to the
+		 * buffer start in cache lines. In most cases this is
+		 * less than one complete cache line, so the value is
+		 * zero */
+		uint64_t back:4;
+		/* The pool that the buffer came from / goes to */
+		uint64_t pool:3;
+		/* The size of the segment pointed to by addr (in bytes) */
+		uint64_t size:16;
+		/* Pointer to the first byte of the data, NOT buffer */
+		uint64_t addr:40;
+#else
+	        uint64_t addr:40;
+	        uint64_t size:16;
+	        uint64_t pool:3;
+	        uint64_t back:4;
+	        uint64_t i:1;
+#endif
+	} s;
+};
+
+#endif /*  __CVMX_PACKET_H__ */
diff --git a/arch/mips/include/asm/octeon/cvmx-pci-defs.h b/arch/mips/include/asm/octeon/cvmx-pci-defs.h
new file mode 100644
index 000000000..be56b693b
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-pci-defs.h
@@ -0,0 +1,2037 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2012 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_PCI_DEFS_H__
+#define __CVMX_PCI_DEFS_H__
+
+#define CVMX_PCI_BAR1_INDEXX(offset) (0x0000000000000100ull + ((offset) & 31) * 4)
+#define CVMX_PCI_BIST_REG (0x00000000000001C0ull)
+#define CVMX_PCI_CFG00 (0x0000000000000000ull)
+#define CVMX_PCI_CFG01 (0x0000000000000004ull)
+#define CVMX_PCI_CFG02 (0x0000000000000008ull)
+#define CVMX_PCI_CFG03 (0x000000000000000Cull)
+#define CVMX_PCI_CFG04 (0x0000000000000010ull)
+#define CVMX_PCI_CFG05 (0x0000000000000014ull)
+#define CVMX_PCI_CFG06 (0x0000000000000018ull)
+#define CVMX_PCI_CFG07 (0x000000000000001Cull)
+#define CVMX_PCI_CFG08 (0x0000000000000020ull)
+#define CVMX_PCI_CFG09 (0x0000000000000024ull)
+#define CVMX_PCI_CFG10 (0x0000000000000028ull)
+#define CVMX_PCI_CFG11 (0x000000000000002Cull)
+#define CVMX_PCI_CFG12 (0x0000000000000030ull)
+#define CVMX_PCI_CFG13 (0x0000000000000034ull)
+#define CVMX_PCI_CFG15 (0x000000000000003Cull)
+#define CVMX_PCI_CFG16 (0x0000000000000040ull)
+#define CVMX_PCI_CFG17 (0x0000000000000044ull)
+#define CVMX_PCI_CFG18 (0x0000000000000048ull)
+#define CVMX_PCI_CFG19 (0x000000000000004Cull)
+#define CVMX_PCI_CFG20 (0x0000000000000050ull)
+#define CVMX_PCI_CFG21 (0x0000000000000054ull)
+#define CVMX_PCI_CFG22 (0x0000000000000058ull)
+#define CVMX_PCI_CFG56 (0x00000000000000E0ull)
+#define CVMX_PCI_CFG57 (0x00000000000000E4ull)
+#define CVMX_PCI_CFG58 (0x00000000000000E8ull)
+#define CVMX_PCI_CFG59 (0x00000000000000ECull)
+#define CVMX_PCI_CFG60 (0x00000000000000F0ull)
+#define CVMX_PCI_CFG61 (0x00000000000000F4ull)
+#define CVMX_PCI_CFG62 (0x00000000000000F8ull)
+#define CVMX_PCI_CFG63 (0x00000000000000FCull)
+#define CVMX_PCI_CNT_REG (0x00000000000001B8ull)
+#define CVMX_PCI_CTL_STATUS_2 (0x000000000000018Cull)
+#define CVMX_PCI_DBELL_X(offset) (0x0000000000000080ull + ((offset) & 3) * 8)
+#define CVMX_PCI_DMA_CNT0 CVMX_PCI_DMA_CNTX(0)
+#define CVMX_PCI_DMA_CNT1 CVMX_PCI_DMA_CNTX(1)
+#define CVMX_PCI_DMA_CNTX(offset) (0x00000000000000A0ull + ((offset) & 1) * 8)
+#define CVMX_PCI_DMA_INT_LEV0 CVMX_PCI_DMA_INT_LEVX(0)
+#define CVMX_PCI_DMA_INT_LEV1 CVMX_PCI_DMA_INT_LEVX(1)
+#define CVMX_PCI_DMA_INT_LEVX(offset) (0x00000000000000A4ull + ((offset) & 1) * 8)
+#define CVMX_PCI_DMA_TIME0 CVMX_PCI_DMA_TIMEX(0)
+#define CVMX_PCI_DMA_TIME1 CVMX_PCI_DMA_TIMEX(1)
+#define CVMX_PCI_DMA_TIMEX(offset) (0x00000000000000B0ull + ((offset) & 1) * 4)
+#define CVMX_PCI_INSTR_COUNT0 CVMX_PCI_INSTR_COUNTX(0)
+#define CVMX_PCI_INSTR_COUNT1 CVMX_PCI_INSTR_COUNTX(1)
+#define CVMX_PCI_INSTR_COUNT2 CVMX_PCI_INSTR_COUNTX(2)
+#define CVMX_PCI_INSTR_COUNT3 CVMX_PCI_INSTR_COUNTX(3)
+#define CVMX_PCI_INSTR_COUNTX(offset) (0x0000000000000084ull + ((offset) & 3) * 8)
+#define CVMX_PCI_INT_ENB (0x0000000000000038ull)
+#define CVMX_PCI_INT_ENB2 (0x00000000000001A0ull)
+#define CVMX_PCI_INT_SUM (0x0000000000000030ull)
+#define CVMX_PCI_INT_SUM2 (0x0000000000000198ull)
+#define CVMX_PCI_MSI_RCV (0x00000000000000F0ull)
+#define CVMX_PCI_PKTS_SENT0 CVMX_PCI_PKTS_SENTX(0)
+#define CVMX_PCI_PKTS_SENT1 CVMX_PCI_PKTS_SENTX(1)
+#define CVMX_PCI_PKTS_SENT2 CVMX_PCI_PKTS_SENTX(2)
+#define CVMX_PCI_PKTS_SENT3 CVMX_PCI_PKTS_SENTX(3)
+#define CVMX_PCI_PKTS_SENTX(offset) (0x0000000000000040ull + ((offset) & 3) * 16)
+#define CVMX_PCI_PKTS_SENT_INT_LEV0 CVMX_PCI_PKTS_SENT_INT_LEVX(0)
+#define CVMX_PCI_PKTS_SENT_INT_LEV1 CVMX_PCI_PKTS_SENT_INT_LEVX(1)
+#define CVMX_PCI_PKTS_SENT_INT_LEV2 CVMX_PCI_PKTS_SENT_INT_LEVX(2)
+#define CVMX_PCI_PKTS_SENT_INT_LEV3 CVMX_PCI_PKTS_SENT_INT_LEVX(3)
+#define CVMX_PCI_PKTS_SENT_INT_LEVX(offset) (0x0000000000000048ull + ((offset) & 3) * 16)
+#define CVMX_PCI_PKTS_SENT_TIME0 CVMX_PCI_PKTS_SENT_TIMEX(0)
+#define CVMX_PCI_PKTS_SENT_TIME1 CVMX_PCI_PKTS_SENT_TIMEX(1)
+#define CVMX_PCI_PKTS_SENT_TIME2 CVMX_PCI_PKTS_SENT_TIMEX(2)
+#define CVMX_PCI_PKTS_SENT_TIME3 CVMX_PCI_PKTS_SENT_TIMEX(3)
+#define CVMX_PCI_PKTS_SENT_TIMEX(offset) (0x000000000000004Cull + ((offset) & 3) * 16)
+#define CVMX_PCI_PKT_CREDITS0 CVMX_PCI_PKT_CREDITSX(0)
+#define CVMX_PCI_PKT_CREDITS1 CVMX_PCI_PKT_CREDITSX(1)
+#define CVMX_PCI_PKT_CREDITS2 CVMX_PCI_PKT_CREDITSX(2)
+#define CVMX_PCI_PKT_CREDITS3 CVMX_PCI_PKT_CREDITSX(3)
+#define CVMX_PCI_PKT_CREDITSX(offset) (0x0000000000000044ull + ((offset) & 3) * 16)
+#define CVMX_PCI_READ_CMD_6 (0x0000000000000180ull)
+#define CVMX_PCI_READ_CMD_C (0x0000000000000184ull)
+#define CVMX_PCI_READ_CMD_E (0x0000000000000188ull)
+#define CVMX_PCI_READ_TIMEOUT (CVMX_ADD_IO_SEG(0x00011F00000000B0ull))
+#define CVMX_PCI_SCM_REG (0x00000000000001A8ull)
+#define CVMX_PCI_TSR_REG (0x00000000000001B0ull)
+#define CVMX_PCI_WIN_RD_ADDR (0x0000000000000008ull)
+#define CVMX_PCI_WIN_RD_DATA (0x0000000000000020ull)
+#define CVMX_PCI_WIN_WR_ADDR (0x0000000000000000ull)
+#define CVMX_PCI_WIN_WR_DATA (0x0000000000000010ull)
+#define CVMX_PCI_WIN_WR_MASK (0x0000000000000018ull)
+
+union cvmx_pci_bar1_indexx {
+	uint32_t u32;
+	struct cvmx_pci_bar1_indexx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t reserved_18_31:14;
+		uint32_t addr_idx:14;
+		uint32_t ca:1;
+		uint32_t end_swp:2;
+		uint32_t addr_v:1;
+#else
+		uint32_t addr_v:1;
+		uint32_t end_swp:2;
+		uint32_t ca:1;
+		uint32_t addr_idx:14;
+		uint32_t reserved_18_31:14;
+#endif
+	} s;
+};
+
+union cvmx_pci_bist_reg {
+	uint64_t u64;
+	struct cvmx_pci_bist_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t rsp_bs:1;
+		uint64_t dma0_bs:1;
+		uint64_t cmd0_bs:1;
+		uint64_t cmd_bs:1;
+		uint64_t csr2p_bs:1;
+		uint64_t csrr_bs:1;
+		uint64_t rsp2p_bs:1;
+		uint64_t csr2n_bs:1;
+		uint64_t dat2n_bs:1;
+		uint64_t dbg2n_bs:1;
+#else
+		uint64_t dbg2n_bs:1;
+		uint64_t dat2n_bs:1;
+		uint64_t csr2n_bs:1;
+		uint64_t rsp2p_bs:1;
+		uint64_t csrr_bs:1;
+		uint64_t csr2p_bs:1;
+		uint64_t cmd_bs:1;
+		uint64_t cmd0_bs:1;
+		uint64_t dma0_bs:1;
+		uint64_t rsp_bs:1;
+		uint64_t reserved_10_63:54;
+#endif
+	} s;
+};
+
+union cvmx_pci_cfg00 {
+	uint32_t u32;
+	struct cvmx_pci_cfg00_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t devid:16;
+		uint32_t vendid:16;
+#else
+		uint32_t vendid:16;
+		uint32_t devid:16;
+#endif
+	} s;
+};
+
+union cvmx_pci_cfg01 {
+	uint32_t u32;
+	struct cvmx_pci_cfg01_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t dpe:1;
+		uint32_t sse:1;
+		uint32_t rma:1;
+		uint32_t rta:1;
+		uint32_t sta:1;
+		uint32_t devt:2;
+		uint32_t mdpe:1;
+		uint32_t fbb:1;
+		uint32_t reserved_22_22:1;
+		uint32_t m66:1;
+		uint32_t cle:1;
+		uint32_t i_stat:1;
+		uint32_t reserved_11_18:8;
+		uint32_t i_dis:1;
+		uint32_t fbbe:1;
+		uint32_t see:1;
+		uint32_t ads:1;
+		uint32_t pee:1;
+		uint32_t vps:1;
+		uint32_t mwice:1;
+		uint32_t scse:1;
+		uint32_t me:1;
+		uint32_t msae:1;
+		uint32_t isae:1;
+#else
+		uint32_t isae:1;
+		uint32_t msae:1;
+		uint32_t me:1;
+		uint32_t scse:1;
+		uint32_t mwice:1;
+		uint32_t vps:1;
+		uint32_t pee:1;
+		uint32_t ads:1;
+		uint32_t see:1;
+		uint32_t fbbe:1;
+		uint32_t i_dis:1;
+		uint32_t reserved_11_18:8;
+		uint32_t i_stat:1;
+		uint32_t cle:1;
+		uint32_t m66:1;
+		uint32_t reserved_22_22:1;
+		uint32_t fbb:1;
+		uint32_t mdpe:1;
+		uint32_t devt:2;
+		uint32_t sta:1;
+		uint32_t rta:1;
+		uint32_t rma:1;
+		uint32_t sse:1;
+		uint32_t dpe:1;
+#endif
+	} s;
+};
+
+union cvmx_pci_cfg02 {
+	uint32_t u32;
+	struct cvmx_pci_cfg02_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t cc:24;
+		uint32_t rid:8;
+#else
+		uint32_t rid:8;
+		uint32_t cc:24;
+#endif
+	} s;
+};
+
+union cvmx_pci_cfg03 {
+	uint32_t u32;
+	struct cvmx_pci_cfg03_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t bcap:1;
+		uint32_t brb:1;
+		uint32_t reserved_28_29:2;
+		uint32_t bcod:4;
+		uint32_t ht:8;
+		uint32_t lt:8;
+		uint32_t cls:8;
+#else
+		uint32_t cls:8;
+		uint32_t lt:8;
+		uint32_t ht:8;
+		uint32_t bcod:4;
+		uint32_t reserved_28_29:2;
+		uint32_t brb:1;
+		uint32_t bcap:1;
+#endif
+	} s;
+};
+
+union cvmx_pci_cfg04 {
+	uint32_t u32;
+	struct cvmx_pci_cfg04_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t lbase:20;
+		uint32_t lbasez:8;
+		uint32_t pf:1;
+		uint32_t typ:2;
+		uint32_t mspc:1;
+#else
+		uint32_t mspc:1;
+		uint32_t typ:2;
+		uint32_t pf:1;
+		uint32_t lbasez:8;
+		uint32_t lbase:20;
+#endif
+	} s;
+};
+
+union cvmx_pci_cfg05 {
+	uint32_t u32;
+	struct cvmx_pci_cfg05_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t hbase:32;
+#else
+		uint32_t hbase:32;
+#endif
+	} s;
+};
+
+union cvmx_pci_cfg06 {
+	uint32_t u32;
+	struct cvmx_pci_cfg06_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t lbase:5;
+		uint32_t lbasez:23;
+		uint32_t pf:1;
+		uint32_t typ:2;
+		uint32_t mspc:1;
+#else
+		uint32_t mspc:1;
+		uint32_t typ:2;
+		uint32_t pf:1;
+		uint32_t lbasez:23;
+		uint32_t lbase:5;
+#endif
+	} s;
+};
+
+union cvmx_pci_cfg07 {
+	uint32_t u32;
+	struct cvmx_pci_cfg07_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t hbase:32;
+#else
+		uint32_t hbase:32;
+#endif
+	} s;
+};
+
+union cvmx_pci_cfg08 {
+	uint32_t u32;
+	struct cvmx_pci_cfg08_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t lbasez:28;
+		uint32_t pf:1;
+		uint32_t typ:2;
+		uint32_t mspc:1;
+#else
+		uint32_t mspc:1;
+		uint32_t typ:2;
+		uint32_t pf:1;
+		uint32_t lbasez:28;
+#endif
+	} s;
+};
+
+union cvmx_pci_cfg09 {
+	uint32_t u32;
+	struct cvmx_pci_cfg09_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t hbase:25;
+		uint32_t hbasez:7;
+#else
+		uint32_t hbasez:7;
+		uint32_t hbase:25;
+#endif
+	} s;
+};
+
+union cvmx_pci_cfg10 {
+	uint32_t u32;
+	struct cvmx_pci_cfg10_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t cisp:32;
+#else
+		uint32_t cisp:32;
+#endif
+	} s;
+};
+
+union cvmx_pci_cfg11 {
+	uint32_t u32;
+	struct cvmx_pci_cfg11_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t ssid:16;
+		uint32_t ssvid:16;
+#else
+		uint32_t ssvid:16;
+		uint32_t ssid:16;
+#endif
+	} s;
+};
+
+union cvmx_pci_cfg12 {
+	uint32_t u32;
+	struct cvmx_pci_cfg12_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t erbar:16;
+		uint32_t erbarz:5;
+		uint32_t reserved_1_10:10;
+		uint32_t erbar_en:1;
+#else
+		uint32_t erbar_en:1;
+		uint32_t reserved_1_10:10;
+		uint32_t erbarz:5;
+		uint32_t erbar:16;
+#endif
+	} s;
+};
+
+union cvmx_pci_cfg13 {
+	uint32_t u32;
+	struct cvmx_pci_cfg13_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t reserved_8_31:24;
+		uint32_t cp:8;
+#else
+		uint32_t cp:8;
+		uint32_t reserved_8_31:24;
+#endif
+	} s;
+};
+
+union cvmx_pci_cfg15 {
+	uint32_t u32;
+	struct cvmx_pci_cfg15_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t ml:8;
+		uint32_t mg:8;
+		uint32_t inta:8;
+		uint32_t il:8;
+#else
+		uint32_t il:8;
+		uint32_t inta:8;
+		uint32_t mg:8;
+		uint32_t ml:8;
+#endif
+	} s;
+};
+
+union cvmx_pci_cfg16 {
+	uint32_t u32;
+	struct cvmx_pci_cfg16_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t trdnpr:1;
+		uint32_t trdard:1;
+		uint32_t rdsati:1;
+		uint32_t trdrs:1;
+		uint32_t trtae:1;
+		uint32_t twsei:1;
+		uint32_t twsen:1;
+		uint32_t twtae:1;
+		uint32_t tmae:1;
+		uint32_t tslte:3;
+		uint32_t tilt:4;
+		uint32_t pbe:12;
+		uint32_t dppmr:1;
+		uint32_t reserved_2_2:1;
+		uint32_t tswc:1;
+		uint32_t mltd:1;
+#else
+		uint32_t mltd:1;
+		uint32_t tswc:1;
+		uint32_t reserved_2_2:1;
+		uint32_t dppmr:1;
+		uint32_t pbe:12;
+		uint32_t tilt:4;
+		uint32_t tslte:3;
+		uint32_t tmae:1;
+		uint32_t twtae:1;
+		uint32_t twsen:1;
+		uint32_t twsei:1;
+		uint32_t trtae:1;
+		uint32_t trdrs:1;
+		uint32_t rdsati:1;
+		uint32_t trdard:1;
+		uint32_t trdnpr:1;
+#endif
+	} s;
+};
+
+union cvmx_pci_cfg17 {
+	uint32_t u32;
+	struct cvmx_pci_cfg17_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t tscme:32;
+#else
+		uint32_t tscme:32;
+#endif
+	} s;
+};
+
+union cvmx_pci_cfg18 {
+	uint32_t u32;
+	struct cvmx_pci_cfg18_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t tdsrps:32;
+#else
+		uint32_t tdsrps:32;
+#endif
+	} s;
+};
+
+union cvmx_pci_cfg19 {
+	uint32_t u32;
+	struct cvmx_pci_cfg19_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t mrbcm:1;
+		uint32_t mrbci:1;
+		uint32_t mdwe:1;
+		uint32_t mdre:1;
+		uint32_t mdrimc:1;
+		uint32_t mdrrmc:3;
+		uint32_t tmes:8;
+		uint32_t teci:1;
+		uint32_t tmei:1;
+		uint32_t tmse:1;
+		uint32_t tmdpes:1;
+		uint32_t tmapes:1;
+		uint32_t reserved_9_10:2;
+		uint32_t tibcd:1;
+		uint32_t tibde:1;
+		uint32_t reserved_6_6:1;
+		uint32_t tidomc:1;
+		uint32_t tdomc:5;
+#else
+		uint32_t tdomc:5;
+		uint32_t tidomc:1;
+		uint32_t reserved_6_6:1;
+		uint32_t tibde:1;
+		uint32_t tibcd:1;
+		uint32_t reserved_9_10:2;
+		uint32_t tmapes:1;
+		uint32_t tmdpes:1;
+		uint32_t tmse:1;
+		uint32_t tmei:1;
+		uint32_t teci:1;
+		uint32_t tmes:8;
+		uint32_t mdrrmc:3;
+		uint32_t mdrimc:1;
+		uint32_t mdre:1;
+		uint32_t mdwe:1;
+		uint32_t mrbci:1;
+		uint32_t mrbcm:1;
+#endif
+	} s;
+};
+
+union cvmx_pci_cfg20 {
+	uint32_t u32;
+	struct cvmx_pci_cfg20_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t mdsp:32;
+#else
+		uint32_t mdsp:32;
+#endif
+	} s;
+};
+
+union cvmx_pci_cfg21 {
+	uint32_t u32;
+	struct cvmx_pci_cfg21_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t scmre:32;
+#else
+		uint32_t scmre:32;
+#endif
+	} s;
+};
+
+union cvmx_pci_cfg22 {
+	uint32_t u32;
+	struct cvmx_pci_cfg22_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t mac:7;
+		uint32_t reserved_19_24:6;
+		uint32_t flush:1;
+		uint32_t mra:1;
+		uint32_t mtta:1;
+		uint32_t mrv:8;
+		uint32_t mttv:8;
+#else
+		uint32_t mttv:8;
+		uint32_t mrv:8;
+		uint32_t mtta:1;
+		uint32_t mra:1;
+		uint32_t flush:1;
+		uint32_t reserved_19_24:6;
+		uint32_t mac:7;
+#endif
+	} s;
+};
+
+union cvmx_pci_cfg56 {
+	uint32_t u32;
+	struct cvmx_pci_cfg56_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t reserved_23_31:9;
+		uint32_t most:3;
+		uint32_t mmbc:2;
+		uint32_t roe:1;
+		uint32_t dpere:1;
+		uint32_t ncp:8;
+		uint32_t pxcid:8;
+#else
+		uint32_t pxcid:8;
+		uint32_t ncp:8;
+		uint32_t dpere:1;
+		uint32_t roe:1;
+		uint32_t mmbc:2;
+		uint32_t most:3;
+		uint32_t reserved_23_31:9;
+#endif
+	} s;
+};
+
+union cvmx_pci_cfg57 {
+	uint32_t u32;
+	struct cvmx_pci_cfg57_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t reserved_30_31:2;
+		uint32_t scemr:1;
+		uint32_t mcrsd:3;
+		uint32_t mostd:3;
+		uint32_t mmrbcd:2;
+		uint32_t dc:1;
+		uint32_t usc:1;
+		uint32_t scd:1;
+		uint32_t m133:1;
+		uint32_t w64:1;
+		uint32_t bn:8;
+		uint32_t dn:5;
+		uint32_t fn:3;
+#else
+		uint32_t fn:3;
+		uint32_t dn:5;
+		uint32_t bn:8;
+		uint32_t w64:1;
+		uint32_t m133:1;
+		uint32_t scd:1;
+		uint32_t usc:1;
+		uint32_t dc:1;
+		uint32_t mmrbcd:2;
+		uint32_t mostd:3;
+		uint32_t mcrsd:3;
+		uint32_t scemr:1;
+		uint32_t reserved_30_31:2;
+#endif
+	} s;
+};
+
+union cvmx_pci_cfg58 {
+	uint32_t u32;
+	struct cvmx_pci_cfg58_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t pmes:5;
+		uint32_t d2s:1;
+		uint32_t d1s:1;
+		uint32_t auxc:3;
+		uint32_t dsi:1;
+		uint32_t reserved_20_20:1;
+		uint32_t pmec:1;
+		uint32_t pcimiv:3;
+		uint32_t ncp:8;
+		uint32_t pmcid:8;
+#else
+		uint32_t pmcid:8;
+		uint32_t ncp:8;
+		uint32_t pcimiv:3;
+		uint32_t pmec:1;
+		uint32_t reserved_20_20:1;
+		uint32_t dsi:1;
+		uint32_t auxc:3;
+		uint32_t d1s:1;
+		uint32_t d2s:1;
+		uint32_t pmes:5;
+#endif
+	} s;
+};
+
+union cvmx_pci_cfg59 {
+	uint32_t u32;
+	struct cvmx_pci_cfg59_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t pmdia:8;
+		uint32_t bpccen:1;
+		uint32_t bd3h:1;
+		uint32_t reserved_16_21:6;
+		uint32_t pmess:1;
+		uint32_t pmedsia:2;
+		uint32_t pmds:4;
+		uint32_t pmeens:1;
+		uint32_t reserved_2_7:6;
+		uint32_t ps:2;
+#else
+		uint32_t ps:2;
+		uint32_t reserved_2_7:6;
+		uint32_t pmeens:1;
+		uint32_t pmds:4;
+		uint32_t pmedsia:2;
+		uint32_t pmess:1;
+		uint32_t reserved_16_21:6;
+		uint32_t bd3h:1;
+		uint32_t bpccen:1;
+		uint32_t pmdia:8;
+#endif
+	} s;
+};
+
+union cvmx_pci_cfg60 {
+	uint32_t u32;
+	struct cvmx_pci_cfg60_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t reserved_24_31:8;
+		uint32_t m64:1;
+		uint32_t mme:3;
+		uint32_t mmc:3;
+		uint32_t msien:1;
+		uint32_t ncp:8;
+		uint32_t msicid:8;
+#else
+		uint32_t msicid:8;
+		uint32_t ncp:8;
+		uint32_t msien:1;
+		uint32_t mmc:3;
+		uint32_t mme:3;
+		uint32_t m64:1;
+		uint32_t reserved_24_31:8;
+#endif
+	} s;
+};
+
+union cvmx_pci_cfg61 {
+	uint32_t u32;
+	struct cvmx_pci_cfg61_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t msi31t2:30;
+		uint32_t reserved_0_1:2;
+#else
+		uint32_t reserved_0_1:2;
+		uint32_t msi31t2:30;
+#endif
+	} s;
+};
+
+union cvmx_pci_cfg62 {
+	uint32_t u32;
+	struct cvmx_pci_cfg62_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t msi:32;
+#else
+		uint32_t msi:32;
+#endif
+	} s;
+};
+
+union cvmx_pci_cfg63 {
+	uint32_t u32;
+	struct cvmx_pci_cfg63_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t reserved_16_31:16;
+		uint32_t msimd:16;
+#else
+		uint32_t msimd:16;
+		uint32_t reserved_16_31:16;
+#endif
+	} s;
+};
+
+union cvmx_pci_cnt_reg {
+	uint64_t u64;
+	struct cvmx_pci_cnt_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_38_63:26;
+		uint64_t hm_pcix:1;
+		uint64_t hm_speed:2;
+		uint64_t ap_pcix:1;
+		uint64_t ap_speed:2;
+		uint64_t pcicnt:32;
+#else
+		uint64_t pcicnt:32;
+		uint64_t ap_speed:2;
+		uint64_t ap_pcix:1;
+		uint64_t hm_speed:2;
+		uint64_t hm_pcix:1;
+		uint64_t reserved_38_63:26;
+#endif
+	} s;
+};
+
+union cvmx_pci_ctl_status_2 {
+	uint32_t u32;
+	struct cvmx_pci_ctl_status_2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t reserved_29_31:3;
+		uint32_t bb1_hole:3;
+		uint32_t bb1_siz:1;
+		uint32_t bb_ca:1;
+		uint32_t bb_es:2;
+		uint32_t bb1:1;
+		uint32_t bb0:1;
+		uint32_t erst_n:1;
+		uint32_t bar2pres:1;
+		uint32_t scmtyp:1;
+		uint32_t scm:1;
+		uint32_t en_wfilt:1;
+		uint32_t reserved_14_14:1;
+		uint32_t ap_pcix:1;
+		uint32_t ap_64ad:1;
+		uint32_t b12_bist:1;
+		uint32_t pmo_amod:1;
+		uint32_t pmo_fpc:3;
+		uint32_t tsr_hwm:3;
+		uint32_t bar2_enb:1;
+		uint32_t bar2_esx:2;
+		uint32_t bar2_cax:1;
+#else
+		uint32_t bar2_cax:1;
+		uint32_t bar2_esx:2;
+		uint32_t bar2_enb:1;
+		uint32_t tsr_hwm:3;
+		uint32_t pmo_fpc:3;
+		uint32_t pmo_amod:1;
+		uint32_t b12_bist:1;
+		uint32_t ap_64ad:1;
+		uint32_t ap_pcix:1;
+		uint32_t reserved_14_14:1;
+		uint32_t en_wfilt:1;
+		uint32_t scm:1;
+		uint32_t scmtyp:1;
+		uint32_t bar2pres:1;
+		uint32_t erst_n:1;
+		uint32_t bb0:1;
+		uint32_t bb1:1;
+		uint32_t bb_es:2;
+		uint32_t bb_ca:1;
+		uint32_t bb1_siz:1;
+		uint32_t bb1_hole:3;
+		uint32_t reserved_29_31:3;
+#endif
+	} s;
+	struct cvmx_pci_ctl_status_2_cn31xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t reserved_20_31:12;
+		uint32_t erst_n:1;
+		uint32_t bar2pres:1;
+		uint32_t scmtyp:1;
+		uint32_t scm:1;
+		uint32_t en_wfilt:1;
+		uint32_t reserved_14_14:1;
+		uint32_t ap_pcix:1;
+		uint32_t ap_64ad:1;
+		uint32_t b12_bist:1;
+		uint32_t pmo_amod:1;
+		uint32_t pmo_fpc:3;
+		uint32_t tsr_hwm:3;
+		uint32_t bar2_enb:1;
+		uint32_t bar2_esx:2;
+		uint32_t bar2_cax:1;
+#else
+		uint32_t bar2_cax:1;
+		uint32_t bar2_esx:2;
+		uint32_t bar2_enb:1;
+		uint32_t tsr_hwm:3;
+		uint32_t pmo_fpc:3;
+		uint32_t pmo_amod:1;
+		uint32_t b12_bist:1;
+		uint32_t ap_64ad:1;
+		uint32_t ap_pcix:1;
+		uint32_t reserved_14_14:1;
+		uint32_t en_wfilt:1;
+		uint32_t scm:1;
+		uint32_t scmtyp:1;
+		uint32_t bar2pres:1;
+		uint32_t erst_n:1;
+		uint32_t reserved_20_31:12;
+#endif
+	} cn31xx;
+};
+
+union cvmx_pci_dbellx {
+	uint32_t u32;
+	struct cvmx_pci_dbellx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t reserved_16_31:16;
+		uint32_t inc_val:16;
+#else
+		uint32_t inc_val:16;
+		uint32_t reserved_16_31:16;
+#endif
+	} s;
+};
+
+union cvmx_pci_dma_cntx {
+	uint32_t u32;
+	struct cvmx_pci_dma_cntx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t dma_cnt:32;
+#else
+		uint32_t dma_cnt:32;
+#endif
+	} s;
+};
+
+union cvmx_pci_dma_int_levx {
+	uint32_t u32;
+	struct cvmx_pci_dma_int_levx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t pkt_cnt:32;
+#else
+		uint32_t pkt_cnt:32;
+#endif
+	} s;
+};
+
+union cvmx_pci_dma_timex {
+	uint32_t u32;
+	struct cvmx_pci_dma_timex_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t dma_time:32;
+#else
+		uint32_t dma_time:32;
+#endif
+	} s;
+};
+
+union cvmx_pci_instr_countx {
+	uint32_t u32;
+	struct cvmx_pci_instr_countx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t icnt:32;
+#else
+		uint32_t icnt:32;
+#endif
+	} s;
+};
+
+union cvmx_pci_int_enb {
+	uint64_t u64;
+	struct cvmx_pci_int_enb_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_34_63:30;
+		uint64_t ill_rd:1;
+		uint64_t ill_wr:1;
+		uint64_t win_wr:1;
+		uint64_t dma1_fi:1;
+		uint64_t dma0_fi:1;
+		uint64_t idtime1:1;
+		uint64_t idtime0:1;
+		uint64_t idcnt1:1;
+		uint64_t idcnt0:1;
+		uint64_t iptime3:1;
+		uint64_t iptime2:1;
+		uint64_t iptime1:1;
+		uint64_t iptime0:1;
+		uint64_t ipcnt3:1;
+		uint64_t ipcnt2:1;
+		uint64_t ipcnt1:1;
+		uint64_t ipcnt0:1;
+		uint64_t irsl_int:1;
+		uint64_t ill_rrd:1;
+		uint64_t ill_rwr:1;
+		uint64_t idperr:1;
+		uint64_t iaperr:1;
+		uint64_t iserr:1;
+		uint64_t itsr_abt:1;
+		uint64_t imsc_msg:1;
+		uint64_t imsi_mabt:1;
+		uint64_t imsi_tabt:1;
+		uint64_t imsi_per:1;
+		uint64_t imr_tto:1;
+		uint64_t imr_abt:1;
+		uint64_t itr_abt:1;
+		uint64_t imr_wtto:1;
+		uint64_t imr_wabt:1;
+		uint64_t itr_wabt:1;
+#else
+		uint64_t itr_wabt:1;
+		uint64_t imr_wabt:1;
+		uint64_t imr_wtto:1;
+		uint64_t itr_abt:1;
+		uint64_t imr_abt:1;
+		uint64_t imr_tto:1;
+		uint64_t imsi_per:1;
+		uint64_t imsi_tabt:1;
+		uint64_t imsi_mabt:1;
+		uint64_t imsc_msg:1;
+		uint64_t itsr_abt:1;
+		uint64_t iserr:1;
+		uint64_t iaperr:1;
+		uint64_t idperr:1;
+		uint64_t ill_rwr:1;
+		uint64_t ill_rrd:1;
+		uint64_t irsl_int:1;
+		uint64_t ipcnt0:1;
+		uint64_t ipcnt1:1;
+		uint64_t ipcnt2:1;
+		uint64_t ipcnt3:1;
+		uint64_t iptime0:1;
+		uint64_t iptime1:1;
+		uint64_t iptime2:1;
+		uint64_t iptime3:1;
+		uint64_t idcnt0:1;
+		uint64_t idcnt1:1;
+		uint64_t idtime0:1;
+		uint64_t idtime1:1;
+		uint64_t dma0_fi:1;
+		uint64_t dma1_fi:1;
+		uint64_t win_wr:1;
+		uint64_t ill_wr:1;
+		uint64_t ill_rd:1;
+		uint64_t reserved_34_63:30;
+#endif
+	} s;
+	struct cvmx_pci_int_enb_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_34_63:30;
+		uint64_t ill_rd:1;
+		uint64_t ill_wr:1;
+		uint64_t win_wr:1;
+		uint64_t dma1_fi:1;
+		uint64_t dma0_fi:1;
+		uint64_t idtime1:1;
+		uint64_t idtime0:1;
+		uint64_t idcnt1:1;
+		uint64_t idcnt0:1;
+		uint64_t reserved_22_24:3;
+		uint64_t iptime0:1;
+		uint64_t reserved_18_20:3;
+		uint64_t ipcnt0:1;
+		uint64_t irsl_int:1;
+		uint64_t ill_rrd:1;
+		uint64_t ill_rwr:1;
+		uint64_t idperr:1;
+		uint64_t iaperr:1;
+		uint64_t iserr:1;
+		uint64_t itsr_abt:1;
+		uint64_t imsc_msg:1;
+		uint64_t imsi_mabt:1;
+		uint64_t imsi_tabt:1;
+		uint64_t imsi_per:1;
+		uint64_t imr_tto:1;
+		uint64_t imr_abt:1;
+		uint64_t itr_abt:1;
+		uint64_t imr_wtto:1;
+		uint64_t imr_wabt:1;
+		uint64_t itr_wabt:1;
+#else
+		uint64_t itr_wabt:1;
+		uint64_t imr_wabt:1;
+		uint64_t imr_wtto:1;
+		uint64_t itr_abt:1;
+		uint64_t imr_abt:1;
+		uint64_t imr_tto:1;
+		uint64_t imsi_per:1;
+		uint64_t imsi_tabt:1;
+		uint64_t imsi_mabt:1;
+		uint64_t imsc_msg:1;
+		uint64_t itsr_abt:1;
+		uint64_t iserr:1;
+		uint64_t iaperr:1;
+		uint64_t idperr:1;
+		uint64_t ill_rwr:1;
+		uint64_t ill_rrd:1;
+		uint64_t irsl_int:1;
+		uint64_t ipcnt0:1;
+		uint64_t reserved_18_20:3;
+		uint64_t iptime0:1;
+		uint64_t reserved_22_24:3;
+		uint64_t idcnt0:1;
+		uint64_t idcnt1:1;
+		uint64_t idtime0:1;
+		uint64_t idtime1:1;
+		uint64_t dma0_fi:1;
+		uint64_t dma1_fi:1;
+		uint64_t win_wr:1;
+		uint64_t ill_wr:1;
+		uint64_t ill_rd:1;
+		uint64_t reserved_34_63:30;
+#endif
+	} cn30xx;
+	struct cvmx_pci_int_enb_cn31xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_34_63:30;
+		uint64_t ill_rd:1;
+		uint64_t ill_wr:1;
+		uint64_t win_wr:1;
+		uint64_t dma1_fi:1;
+		uint64_t dma0_fi:1;
+		uint64_t idtime1:1;
+		uint64_t idtime0:1;
+		uint64_t idcnt1:1;
+		uint64_t idcnt0:1;
+		uint64_t reserved_23_24:2;
+		uint64_t iptime1:1;
+		uint64_t iptime0:1;
+		uint64_t reserved_19_20:2;
+		uint64_t ipcnt1:1;
+		uint64_t ipcnt0:1;
+		uint64_t irsl_int:1;
+		uint64_t ill_rrd:1;
+		uint64_t ill_rwr:1;
+		uint64_t idperr:1;
+		uint64_t iaperr:1;
+		uint64_t iserr:1;
+		uint64_t itsr_abt:1;
+		uint64_t imsc_msg:1;
+		uint64_t imsi_mabt:1;
+		uint64_t imsi_tabt:1;
+		uint64_t imsi_per:1;
+		uint64_t imr_tto:1;
+		uint64_t imr_abt:1;
+		uint64_t itr_abt:1;
+		uint64_t imr_wtto:1;
+		uint64_t imr_wabt:1;
+		uint64_t itr_wabt:1;
+#else
+		uint64_t itr_wabt:1;
+		uint64_t imr_wabt:1;
+		uint64_t imr_wtto:1;
+		uint64_t itr_abt:1;
+		uint64_t imr_abt:1;
+		uint64_t imr_tto:1;
+		uint64_t imsi_per:1;
+		uint64_t imsi_tabt:1;
+		uint64_t imsi_mabt:1;
+		uint64_t imsc_msg:1;
+		uint64_t itsr_abt:1;
+		uint64_t iserr:1;
+		uint64_t iaperr:1;
+		uint64_t idperr:1;
+		uint64_t ill_rwr:1;
+		uint64_t ill_rrd:1;
+		uint64_t irsl_int:1;
+		uint64_t ipcnt0:1;
+		uint64_t ipcnt1:1;
+		uint64_t reserved_19_20:2;
+		uint64_t iptime0:1;
+		uint64_t iptime1:1;
+		uint64_t reserved_23_24:2;
+		uint64_t idcnt0:1;
+		uint64_t idcnt1:1;
+		uint64_t idtime0:1;
+		uint64_t idtime1:1;
+		uint64_t dma0_fi:1;
+		uint64_t dma1_fi:1;
+		uint64_t win_wr:1;
+		uint64_t ill_wr:1;
+		uint64_t ill_rd:1;
+		uint64_t reserved_34_63:30;
+#endif
+	} cn31xx;
+};
+
+union cvmx_pci_int_enb2 {
+	uint64_t u64;
+	struct cvmx_pci_int_enb2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_34_63:30;
+		uint64_t ill_rd:1;
+		uint64_t ill_wr:1;
+		uint64_t win_wr:1;
+		uint64_t dma1_fi:1;
+		uint64_t dma0_fi:1;
+		uint64_t rdtime1:1;
+		uint64_t rdtime0:1;
+		uint64_t rdcnt1:1;
+		uint64_t rdcnt0:1;
+		uint64_t rptime3:1;
+		uint64_t rptime2:1;
+		uint64_t rptime1:1;
+		uint64_t rptime0:1;
+		uint64_t rpcnt3:1;
+		uint64_t rpcnt2:1;
+		uint64_t rpcnt1:1;
+		uint64_t rpcnt0:1;
+		uint64_t rrsl_int:1;
+		uint64_t ill_rrd:1;
+		uint64_t ill_rwr:1;
+		uint64_t rdperr:1;
+		uint64_t raperr:1;
+		uint64_t rserr:1;
+		uint64_t rtsr_abt:1;
+		uint64_t rmsc_msg:1;
+		uint64_t rmsi_mabt:1;
+		uint64_t rmsi_tabt:1;
+		uint64_t rmsi_per:1;
+		uint64_t rmr_tto:1;
+		uint64_t rmr_abt:1;
+		uint64_t rtr_abt:1;
+		uint64_t rmr_wtto:1;
+		uint64_t rmr_wabt:1;
+		uint64_t rtr_wabt:1;
+#else
+		uint64_t rtr_wabt:1;
+		uint64_t rmr_wabt:1;
+		uint64_t rmr_wtto:1;
+		uint64_t rtr_abt:1;
+		uint64_t rmr_abt:1;
+		uint64_t rmr_tto:1;
+		uint64_t rmsi_per:1;
+		uint64_t rmsi_tabt:1;
+		uint64_t rmsi_mabt:1;
+		uint64_t rmsc_msg:1;
+		uint64_t rtsr_abt:1;
+		uint64_t rserr:1;
+		uint64_t raperr:1;
+		uint64_t rdperr:1;
+		uint64_t ill_rwr:1;
+		uint64_t ill_rrd:1;
+		uint64_t rrsl_int:1;
+		uint64_t rpcnt0:1;
+		uint64_t rpcnt1:1;
+		uint64_t rpcnt2:1;
+		uint64_t rpcnt3:1;
+		uint64_t rptime0:1;
+		uint64_t rptime1:1;
+		uint64_t rptime2:1;
+		uint64_t rptime3:1;
+		uint64_t rdcnt0:1;
+		uint64_t rdcnt1:1;
+		uint64_t rdtime0:1;
+		uint64_t rdtime1:1;
+		uint64_t dma0_fi:1;
+		uint64_t dma1_fi:1;
+		uint64_t win_wr:1;
+		uint64_t ill_wr:1;
+		uint64_t ill_rd:1;
+		uint64_t reserved_34_63:30;
+#endif
+	} s;
+	struct cvmx_pci_int_enb2_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_34_63:30;
+		uint64_t ill_rd:1;
+		uint64_t ill_wr:1;
+		uint64_t win_wr:1;
+		uint64_t dma1_fi:1;
+		uint64_t dma0_fi:1;
+		uint64_t rdtime1:1;
+		uint64_t rdtime0:1;
+		uint64_t rdcnt1:1;
+		uint64_t rdcnt0:1;
+		uint64_t reserved_22_24:3;
+		uint64_t rptime0:1;
+		uint64_t reserved_18_20:3;
+		uint64_t rpcnt0:1;
+		uint64_t rrsl_int:1;
+		uint64_t ill_rrd:1;
+		uint64_t ill_rwr:1;
+		uint64_t rdperr:1;
+		uint64_t raperr:1;
+		uint64_t rserr:1;
+		uint64_t rtsr_abt:1;
+		uint64_t rmsc_msg:1;
+		uint64_t rmsi_mabt:1;
+		uint64_t rmsi_tabt:1;
+		uint64_t rmsi_per:1;
+		uint64_t rmr_tto:1;
+		uint64_t rmr_abt:1;
+		uint64_t rtr_abt:1;
+		uint64_t rmr_wtto:1;
+		uint64_t rmr_wabt:1;
+		uint64_t rtr_wabt:1;
+#else
+		uint64_t rtr_wabt:1;
+		uint64_t rmr_wabt:1;
+		uint64_t rmr_wtto:1;
+		uint64_t rtr_abt:1;
+		uint64_t rmr_abt:1;
+		uint64_t rmr_tto:1;
+		uint64_t rmsi_per:1;
+		uint64_t rmsi_tabt:1;
+		uint64_t rmsi_mabt:1;
+		uint64_t rmsc_msg:1;
+		uint64_t rtsr_abt:1;
+		uint64_t rserr:1;
+		uint64_t raperr:1;
+		uint64_t rdperr:1;
+		uint64_t ill_rwr:1;
+		uint64_t ill_rrd:1;
+		uint64_t rrsl_int:1;
+		uint64_t rpcnt0:1;
+		uint64_t reserved_18_20:3;
+		uint64_t rptime0:1;
+		uint64_t reserved_22_24:3;
+		uint64_t rdcnt0:1;
+		uint64_t rdcnt1:1;
+		uint64_t rdtime0:1;
+		uint64_t rdtime1:1;
+		uint64_t dma0_fi:1;
+		uint64_t dma1_fi:1;
+		uint64_t win_wr:1;
+		uint64_t ill_wr:1;
+		uint64_t ill_rd:1;
+		uint64_t reserved_34_63:30;
+#endif
+	} cn30xx;
+	struct cvmx_pci_int_enb2_cn31xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_34_63:30;
+		uint64_t ill_rd:1;
+		uint64_t ill_wr:1;
+		uint64_t win_wr:1;
+		uint64_t dma1_fi:1;
+		uint64_t dma0_fi:1;
+		uint64_t rdtime1:1;
+		uint64_t rdtime0:1;
+		uint64_t rdcnt1:1;
+		uint64_t rdcnt0:1;
+		uint64_t reserved_23_24:2;
+		uint64_t rptime1:1;
+		uint64_t rptime0:1;
+		uint64_t reserved_19_20:2;
+		uint64_t rpcnt1:1;
+		uint64_t rpcnt0:1;
+		uint64_t rrsl_int:1;
+		uint64_t ill_rrd:1;
+		uint64_t ill_rwr:1;
+		uint64_t rdperr:1;
+		uint64_t raperr:1;
+		uint64_t rserr:1;
+		uint64_t rtsr_abt:1;
+		uint64_t rmsc_msg:1;
+		uint64_t rmsi_mabt:1;
+		uint64_t rmsi_tabt:1;
+		uint64_t rmsi_per:1;
+		uint64_t rmr_tto:1;
+		uint64_t rmr_abt:1;
+		uint64_t rtr_abt:1;
+		uint64_t rmr_wtto:1;
+		uint64_t rmr_wabt:1;
+		uint64_t rtr_wabt:1;
+#else
+		uint64_t rtr_wabt:1;
+		uint64_t rmr_wabt:1;
+		uint64_t rmr_wtto:1;
+		uint64_t rtr_abt:1;
+		uint64_t rmr_abt:1;
+		uint64_t rmr_tto:1;
+		uint64_t rmsi_per:1;
+		uint64_t rmsi_tabt:1;
+		uint64_t rmsi_mabt:1;
+		uint64_t rmsc_msg:1;
+		uint64_t rtsr_abt:1;
+		uint64_t rserr:1;
+		uint64_t raperr:1;
+		uint64_t rdperr:1;
+		uint64_t ill_rwr:1;
+		uint64_t ill_rrd:1;
+		uint64_t rrsl_int:1;
+		uint64_t rpcnt0:1;
+		uint64_t rpcnt1:1;
+		uint64_t reserved_19_20:2;
+		uint64_t rptime0:1;
+		uint64_t rptime1:1;
+		uint64_t reserved_23_24:2;
+		uint64_t rdcnt0:1;
+		uint64_t rdcnt1:1;
+		uint64_t rdtime0:1;
+		uint64_t rdtime1:1;
+		uint64_t dma0_fi:1;
+		uint64_t dma1_fi:1;
+		uint64_t win_wr:1;
+		uint64_t ill_wr:1;
+		uint64_t ill_rd:1;
+		uint64_t reserved_34_63:30;
+#endif
+	} cn31xx;
+};
+
+union cvmx_pci_int_sum {
+	uint64_t u64;
+	struct cvmx_pci_int_sum_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_34_63:30;
+		uint64_t ill_rd:1;
+		uint64_t ill_wr:1;
+		uint64_t win_wr:1;
+		uint64_t dma1_fi:1;
+		uint64_t dma0_fi:1;
+		uint64_t dtime1:1;
+		uint64_t dtime0:1;
+		uint64_t dcnt1:1;
+		uint64_t dcnt0:1;
+		uint64_t ptime3:1;
+		uint64_t ptime2:1;
+		uint64_t ptime1:1;
+		uint64_t ptime0:1;
+		uint64_t pcnt3:1;
+		uint64_t pcnt2:1;
+		uint64_t pcnt1:1;
+		uint64_t pcnt0:1;
+		uint64_t rsl_int:1;
+		uint64_t ill_rrd:1;
+		uint64_t ill_rwr:1;
+		uint64_t dperr:1;
+		uint64_t aperr:1;
+		uint64_t serr:1;
+		uint64_t tsr_abt:1;
+		uint64_t msc_msg:1;
+		uint64_t msi_mabt:1;
+		uint64_t msi_tabt:1;
+		uint64_t msi_per:1;
+		uint64_t mr_tto:1;
+		uint64_t mr_abt:1;
+		uint64_t tr_abt:1;
+		uint64_t mr_wtto:1;
+		uint64_t mr_wabt:1;
+		uint64_t tr_wabt:1;
+#else
+		uint64_t tr_wabt:1;
+		uint64_t mr_wabt:1;
+		uint64_t mr_wtto:1;
+		uint64_t tr_abt:1;
+		uint64_t mr_abt:1;
+		uint64_t mr_tto:1;
+		uint64_t msi_per:1;
+		uint64_t msi_tabt:1;
+		uint64_t msi_mabt:1;
+		uint64_t msc_msg:1;
+		uint64_t tsr_abt:1;
+		uint64_t serr:1;
+		uint64_t aperr:1;
+		uint64_t dperr:1;
+		uint64_t ill_rwr:1;
+		uint64_t ill_rrd:1;
+		uint64_t rsl_int:1;
+		uint64_t pcnt0:1;
+		uint64_t pcnt1:1;
+		uint64_t pcnt2:1;
+		uint64_t pcnt3:1;
+		uint64_t ptime0:1;
+		uint64_t ptime1:1;
+		uint64_t ptime2:1;
+		uint64_t ptime3:1;
+		uint64_t dcnt0:1;
+		uint64_t dcnt1:1;
+		uint64_t dtime0:1;
+		uint64_t dtime1:1;
+		uint64_t dma0_fi:1;
+		uint64_t dma1_fi:1;
+		uint64_t win_wr:1;
+		uint64_t ill_wr:1;
+		uint64_t ill_rd:1;
+		uint64_t reserved_34_63:30;
+#endif
+	} s;
+	struct cvmx_pci_int_sum_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_34_63:30;
+		uint64_t ill_rd:1;
+		uint64_t ill_wr:1;
+		uint64_t win_wr:1;
+		uint64_t dma1_fi:1;
+		uint64_t dma0_fi:1;
+		uint64_t dtime1:1;
+		uint64_t dtime0:1;
+		uint64_t dcnt1:1;
+		uint64_t dcnt0:1;
+		uint64_t reserved_22_24:3;
+		uint64_t ptime0:1;
+		uint64_t reserved_18_20:3;
+		uint64_t pcnt0:1;
+		uint64_t rsl_int:1;
+		uint64_t ill_rrd:1;
+		uint64_t ill_rwr:1;
+		uint64_t dperr:1;
+		uint64_t aperr:1;
+		uint64_t serr:1;
+		uint64_t tsr_abt:1;
+		uint64_t msc_msg:1;
+		uint64_t msi_mabt:1;
+		uint64_t msi_tabt:1;
+		uint64_t msi_per:1;
+		uint64_t mr_tto:1;
+		uint64_t mr_abt:1;
+		uint64_t tr_abt:1;
+		uint64_t mr_wtto:1;
+		uint64_t mr_wabt:1;
+		uint64_t tr_wabt:1;
+#else
+		uint64_t tr_wabt:1;
+		uint64_t mr_wabt:1;
+		uint64_t mr_wtto:1;
+		uint64_t tr_abt:1;
+		uint64_t mr_abt:1;
+		uint64_t mr_tto:1;
+		uint64_t msi_per:1;
+		uint64_t msi_tabt:1;
+		uint64_t msi_mabt:1;
+		uint64_t msc_msg:1;
+		uint64_t tsr_abt:1;
+		uint64_t serr:1;
+		uint64_t aperr:1;
+		uint64_t dperr:1;
+		uint64_t ill_rwr:1;
+		uint64_t ill_rrd:1;
+		uint64_t rsl_int:1;
+		uint64_t pcnt0:1;
+		uint64_t reserved_18_20:3;
+		uint64_t ptime0:1;
+		uint64_t reserved_22_24:3;
+		uint64_t dcnt0:1;
+		uint64_t dcnt1:1;
+		uint64_t dtime0:1;
+		uint64_t dtime1:1;
+		uint64_t dma0_fi:1;
+		uint64_t dma1_fi:1;
+		uint64_t win_wr:1;
+		uint64_t ill_wr:1;
+		uint64_t ill_rd:1;
+		uint64_t reserved_34_63:30;
+#endif
+	} cn30xx;
+	struct cvmx_pci_int_sum_cn31xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_34_63:30;
+		uint64_t ill_rd:1;
+		uint64_t ill_wr:1;
+		uint64_t win_wr:1;
+		uint64_t dma1_fi:1;
+		uint64_t dma0_fi:1;
+		uint64_t dtime1:1;
+		uint64_t dtime0:1;
+		uint64_t dcnt1:1;
+		uint64_t dcnt0:1;
+		uint64_t reserved_23_24:2;
+		uint64_t ptime1:1;
+		uint64_t ptime0:1;
+		uint64_t reserved_19_20:2;
+		uint64_t pcnt1:1;
+		uint64_t pcnt0:1;
+		uint64_t rsl_int:1;
+		uint64_t ill_rrd:1;
+		uint64_t ill_rwr:1;
+		uint64_t dperr:1;
+		uint64_t aperr:1;
+		uint64_t serr:1;
+		uint64_t tsr_abt:1;
+		uint64_t msc_msg:1;
+		uint64_t msi_mabt:1;
+		uint64_t msi_tabt:1;
+		uint64_t msi_per:1;
+		uint64_t mr_tto:1;
+		uint64_t mr_abt:1;
+		uint64_t tr_abt:1;
+		uint64_t mr_wtto:1;
+		uint64_t mr_wabt:1;
+		uint64_t tr_wabt:1;
+#else
+		uint64_t tr_wabt:1;
+		uint64_t mr_wabt:1;
+		uint64_t mr_wtto:1;
+		uint64_t tr_abt:1;
+		uint64_t mr_abt:1;
+		uint64_t mr_tto:1;
+		uint64_t msi_per:1;
+		uint64_t msi_tabt:1;
+		uint64_t msi_mabt:1;
+		uint64_t msc_msg:1;
+		uint64_t tsr_abt:1;
+		uint64_t serr:1;
+		uint64_t aperr:1;
+		uint64_t dperr:1;
+		uint64_t ill_rwr:1;
+		uint64_t ill_rrd:1;
+		uint64_t rsl_int:1;
+		uint64_t pcnt0:1;
+		uint64_t pcnt1:1;
+		uint64_t reserved_19_20:2;
+		uint64_t ptime0:1;
+		uint64_t ptime1:1;
+		uint64_t reserved_23_24:2;
+		uint64_t dcnt0:1;
+		uint64_t dcnt1:1;
+		uint64_t dtime0:1;
+		uint64_t dtime1:1;
+		uint64_t dma0_fi:1;
+		uint64_t dma1_fi:1;
+		uint64_t win_wr:1;
+		uint64_t ill_wr:1;
+		uint64_t ill_rd:1;
+		uint64_t reserved_34_63:30;
+#endif
+	} cn31xx;
+};
+
+union cvmx_pci_int_sum2 {
+	uint64_t u64;
+	struct cvmx_pci_int_sum2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_34_63:30;
+		uint64_t ill_rd:1;
+		uint64_t ill_wr:1;
+		uint64_t win_wr:1;
+		uint64_t dma1_fi:1;
+		uint64_t dma0_fi:1;
+		uint64_t dtime1:1;
+		uint64_t dtime0:1;
+		uint64_t dcnt1:1;
+		uint64_t dcnt0:1;
+		uint64_t ptime3:1;
+		uint64_t ptime2:1;
+		uint64_t ptime1:1;
+		uint64_t ptime0:1;
+		uint64_t pcnt3:1;
+		uint64_t pcnt2:1;
+		uint64_t pcnt1:1;
+		uint64_t pcnt0:1;
+		uint64_t rsl_int:1;
+		uint64_t ill_rrd:1;
+		uint64_t ill_rwr:1;
+		uint64_t dperr:1;
+		uint64_t aperr:1;
+		uint64_t serr:1;
+		uint64_t tsr_abt:1;
+		uint64_t msc_msg:1;
+		uint64_t msi_mabt:1;
+		uint64_t msi_tabt:1;
+		uint64_t msi_per:1;
+		uint64_t mr_tto:1;
+		uint64_t mr_abt:1;
+		uint64_t tr_abt:1;
+		uint64_t mr_wtto:1;
+		uint64_t mr_wabt:1;
+		uint64_t tr_wabt:1;
+#else
+		uint64_t tr_wabt:1;
+		uint64_t mr_wabt:1;
+		uint64_t mr_wtto:1;
+		uint64_t tr_abt:1;
+		uint64_t mr_abt:1;
+		uint64_t mr_tto:1;
+		uint64_t msi_per:1;
+		uint64_t msi_tabt:1;
+		uint64_t msi_mabt:1;
+		uint64_t msc_msg:1;
+		uint64_t tsr_abt:1;
+		uint64_t serr:1;
+		uint64_t aperr:1;
+		uint64_t dperr:1;
+		uint64_t ill_rwr:1;
+		uint64_t ill_rrd:1;
+		uint64_t rsl_int:1;
+		uint64_t pcnt0:1;
+		uint64_t pcnt1:1;
+		uint64_t pcnt2:1;
+		uint64_t pcnt3:1;
+		uint64_t ptime0:1;
+		uint64_t ptime1:1;
+		uint64_t ptime2:1;
+		uint64_t ptime3:1;
+		uint64_t dcnt0:1;
+		uint64_t dcnt1:1;
+		uint64_t dtime0:1;
+		uint64_t dtime1:1;
+		uint64_t dma0_fi:1;
+		uint64_t dma1_fi:1;
+		uint64_t win_wr:1;
+		uint64_t ill_wr:1;
+		uint64_t ill_rd:1;
+		uint64_t reserved_34_63:30;
+#endif
+	} s;
+	struct cvmx_pci_int_sum2_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_34_63:30;
+		uint64_t ill_rd:1;
+		uint64_t ill_wr:1;
+		uint64_t win_wr:1;
+		uint64_t dma1_fi:1;
+		uint64_t dma0_fi:1;
+		uint64_t dtime1:1;
+		uint64_t dtime0:1;
+		uint64_t dcnt1:1;
+		uint64_t dcnt0:1;
+		uint64_t reserved_22_24:3;
+		uint64_t ptime0:1;
+		uint64_t reserved_18_20:3;
+		uint64_t pcnt0:1;
+		uint64_t rsl_int:1;
+		uint64_t ill_rrd:1;
+		uint64_t ill_rwr:1;
+		uint64_t dperr:1;
+		uint64_t aperr:1;
+		uint64_t serr:1;
+		uint64_t tsr_abt:1;
+		uint64_t msc_msg:1;
+		uint64_t msi_mabt:1;
+		uint64_t msi_tabt:1;
+		uint64_t msi_per:1;
+		uint64_t mr_tto:1;
+		uint64_t mr_abt:1;
+		uint64_t tr_abt:1;
+		uint64_t mr_wtto:1;
+		uint64_t mr_wabt:1;
+		uint64_t tr_wabt:1;
+#else
+		uint64_t tr_wabt:1;
+		uint64_t mr_wabt:1;
+		uint64_t mr_wtto:1;
+		uint64_t tr_abt:1;
+		uint64_t mr_abt:1;
+		uint64_t mr_tto:1;
+		uint64_t msi_per:1;
+		uint64_t msi_tabt:1;
+		uint64_t msi_mabt:1;
+		uint64_t msc_msg:1;
+		uint64_t tsr_abt:1;
+		uint64_t serr:1;
+		uint64_t aperr:1;
+		uint64_t dperr:1;
+		uint64_t ill_rwr:1;
+		uint64_t ill_rrd:1;
+		uint64_t rsl_int:1;
+		uint64_t pcnt0:1;
+		uint64_t reserved_18_20:3;
+		uint64_t ptime0:1;
+		uint64_t reserved_22_24:3;
+		uint64_t dcnt0:1;
+		uint64_t dcnt1:1;
+		uint64_t dtime0:1;
+		uint64_t dtime1:1;
+		uint64_t dma0_fi:1;
+		uint64_t dma1_fi:1;
+		uint64_t win_wr:1;
+		uint64_t ill_wr:1;
+		uint64_t ill_rd:1;
+		uint64_t reserved_34_63:30;
+#endif
+	} cn30xx;
+	struct cvmx_pci_int_sum2_cn31xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_34_63:30;
+		uint64_t ill_rd:1;
+		uint64_t ill_wr:1;
+		uint64_t win_wr:1;
+		uint64_t dma1_fi:1;
+		uint64_t dma0_fi:1;
+		uint64_t dtime1:1;
+		uint64_t dtime0:1;
+		uint64_t dcnt1:1;
+		uint64_t dcnt0:1;
+		uint64_t reserved_23_24:2;
+		uint64_t ptime1:1;
+		uint64_t ptime0:1;
+		uint64_t reserved_19_20:2;
+		uint64_t pcnt1:1;
+		uint64_t pcnt0:1;
+		uint64_t rsl_int:1;
+		uint64_t ill_rrd:1;
+		uint64_t ill_rwr:1;
+		uint64_t dperr:1;
+		uint64_t aperr:1;
+		uint64_t serr:1;
+		uint64_t tsr_abt:1;
+		uint64_t msc_msg:1;
+		uint64_t msi_mabt:1;
+		uint64_t msi_tabt:1;
+		uint64_t msi_per:1;
+		uint64_t mr_tto:1;
+		uint64_t mr_abt:1;
+		uint64_t tr_abt:1;
+		uint64_t mr_wtto:1;
+		uint64_t mr_wabt:1;
+		uint64_t tr_wabt:1;
+#else
+		uint64_t tr_wabt:1;
+		uint64_t mr_wabt:1;
+		uint64_t mr_wtto:1;
+		uint64_t tr_abt:1;
+		uint64_t mr_abt:1;
+		uint64_t mr_tto:1;
+		uint64_t msi_per:1;
+		uint64_t msi_tabt:1;
+		uint64_t msi_mabt:1;
+		uint64_t msc_msg:1;
+		uint64_t tsr_abt:1;
+		uint64_t serr:1;
+		uint64_t aperr:1;
+		uint64_t dperr:1;
+		uint64_t ill_rwr:1;
+		uint64_t ill_rrd:1;
+		uint64_t rsl_int:1;
+		uint64_t pcnt0:1;
+		uint64_t pcnt1:1;
+		uint64_t reserved_19_20:2;
+		uint64_t ptime0:1;
+		uint64_t ptime1:1;
+		uint64_t reserved_23_24:2;
+		uint64_t dcnt0:1;
+		uint64_t dcnt1:1;
+		uint64_t dtime0:1;
+		uint64_t dtime1:1;
+		uint64_t dma0_fi:1;
+		uint64_t dma1_fi:1;
+		uint64_t win_wr:1;
+		uint64_t ill_wr:1;
+		uint64_t ill_rd:1;
+		uint64_t reserved_34_63:30;
+#endif
+	} cn31xx;
+};
+
+union cvmx_pci_msi_rcv {
+	uint32_t u32;
+	struct cvmx_pci_msi_rcv_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t reserved_6_31:26;
+		uint32_t intr:6;
+#else
+		uint32_t intr:6;
+		uint32_t reserved_6_31:26;
+#endif
+	} s;
+};
+
+union cvmx_pci_pkt_creditsx {
+	uint32_t u32;
+	struct cvmx_pci_pkt_creditsx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t pkt_cnt:16;
+		uint32_t ptr_cnt:16;
+#else
+		uint32_t ptr_cnt:16;
+		uint32_t pkt_cnt:16;
+#endif
+	} s;
+};
+
+union cvmx_pci_pkts_sentx {
+	uint32_t u32;
+	struct cvmx_pci_pkts_sentx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t pkt_cnt:32;
+#else
+		uint32_t pkt_cnt:32;
+#endif
+	} s;
+};
+
+union cvmx_pci_pkts_sent_int_levx {
+	uint32_t u32;
+	struct cvmx_pci_pkts_sent_int_levx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t pkt_cnt:32;
+#else
+		uint32_t pkt_cnt:32;
+#endif
+	} s;
+};
+
+union cvmx_pci_pkts_sent_timex {
+	uint32_t u32;
+	struct cvmx_pci_pkts_sent_timex_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t pkt_time:32;
+#else
+		uint32_t pkt_time:32;
+#endif
+	} s;
+};
+
+union cvmx_pci_read_cmd_6 {
+	uint32_t u32;
+	struct cvmx_pci_read_cmd_6_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t reserved_9_31:23;
+		uint32_t min_data:6;
+		uint32_t prefetch:3;
+#else
+		uint32_t prefetch:3;
+		uint32_t min_data:6;
+		uint32_t reserved_9_31:23;
+#endif
+	} s;
+};
+
+union cvmx_pci_read_cmd_c {
+	uint32_t u32;
+	struct cvmx_pci_read_cmd_c_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t reserved_9_31:23;
+		uint32_t min_data:6;
+		uint32_t prefetch:3;
+#else
+		uint32_t prefetch:3;
+		uint32_t min_data:6;
+		uint32_t reserved_9_31:23;
+#endif
+	} s;
+};
+
+union cvmx_pci_read_cmd_e {
+	uint32_t u32;
+	struct cvmx_pci_read_cmd_e_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint32_t reserved_9_31:23;
+		uint32_t min_data:6;
+		uint32_t prefetch:3;
+#else
+		uint32_t prefetch:3;
+		uint32_t min_data:6;
+		uint32_t reserved_9_31:23;
+#endif
+	} s;
+};
+
+union cvmx_pci_read_timeout {
+	uint64_t u64;
+	struct cvmx_pci_read_timeout_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t enb:1;
+		uint64_t cnt:31;
+#else
+		uint64_t cnt:31;
+		uint64_t enb:1;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_pci_scm_reg {
+	uint64_t u64;
+	struct cvmx_pci_scm_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t scm:32;
+#else
+		uint64_t scm:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_pci_tsr_reg {
+	uint64_t u64;
+	struct cvmx_pci_tsr_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_36_63:28;
+		uint64_t tsr:36;
+#else
+		uint64_t tsr:36;
+		uint64_t reserved_36_63:28;
+#endif
+	} s;
+};
+
+union cvmx_pci_win_rd_addr {
+	uint64_t u64;
+	struct cvmx_pci_win_rd_addr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_49_63:15;
+		uint64_t iobit:1;
+		uint64_t reserved_0_47:48;
+#else
+		uint64_t reserved_0_47:48;
+		uint64_t iobit:1;
+		uint64_t reserved_49_63:15;
+#endif
+	} s;
+	struct cvmx_pci_win_rd_addr_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_49_63:15;
+		uint64_t iobit:1;
+		uint64_t rd_addr:46;
+		uint64_t reserved_0_1:2;
+#else
+		uint64_t reserved_0_1:2;
+		uint64_t rd_addr:46;
+		uint64_t iobit:1;
+		uint64_t reserved_49_63:15;
+#endif
+	} cn30xx;
+	struct cvmx_pci_win_rd_addr_cn38xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_49_63:15;
+		uint64_t iobit:1;
+		uint64_t rd_addr:45;
+		uint64_t reserved_0_2:3;
+#else
+		uint64_t reserved_0_2:3;
+		uint64_t rd_addr:45;
+		uint64_t iobit:1;
+		uint64_t reserved_49_63:15;
+#endif
+	} cn38xx;
+};
+
+union cvmx_pci_win_rd_data {
+	uint64_t u64;
+	struct cvmx_pci_win_rd_data_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t rd_data:64;
+#else
+		uint64_t rd_data:64;
+#endif
+	} s;
+};
+
+union cvmx_pci_win_wr_addr {
+	uint64_t u64;
+	struct cvmx_pci_win_wr_addr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_49_63:15;
+		uint64_t iobit:1;
+		uint64_t wr_addr:45;
+		uint64_t reserved_0_2:3;
+#else
+		uint64_t reserved_0_2:3;
+		uint64_t wr_addr:45;
+		uint64_t iobit:1;
+		uint64_t reserved_49_63:15;
+#endif
+	} s;
+};
+
+union cvmx_pci_win_wr_data {
+	uint64_t u64;
+	struct cvmx_pci_win_wr_data_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t wr_data:64;
+#else
+		uint64_t wr_data:64;
+#endif
+	} s;
+};
+
+union cvmx_pci_win_wr_mask {
+	uint64_t u64;
+	struct cvmx_pci_win_wr_mask_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t wr_mask:8;
+#else
+		uint64_t wr_mask:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-pciercx-defs.h b/arch/mips/include/asm/octeon/cvmx-pciercx-defs.h
new file mode 100644
index 000000000..e2dce1acf
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-pciercx-defs.h
@@ -0,0 +1,368 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2017 Cavium, Inc.
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_PCIERCX_DEFS_H__
+#define __CVMX_PCIERCX_DEFS_H__
+
+#include <uapi/asm/bitfield.h>
+
+#define CVMX_PCIERCX_CFG001(block_id) (0x0000000000000004ull)
+#define CVMX_PCIERCX_CFG006(block_id) (0x0000000000000018ull)
+#define CVMX_PCIERCX_CFG008(block_id) (0x0000000000000020ull)
+#define CVMX_PCIERCX_CFG009(block_id) (0x0000000000000024ull)
+#define CVMX_PCIERCX_CFG010(block_id) (0x0000000000000028ull)
+#define CVMX_PCIERCX_CFG011(block_id) (0x000000000000002Cull)
+#define CVMX_PCIERCX_CFG030(block_id) (0x0000000000000078ull)
+#define CVMX_PCIERCX_CFG031(block_id) (0x000000000000007Cull)
+#define CVMX_PCIERCX_CFG032(block_id) (0x0000000000000080ull)
+#define CVMX_PCIERCX_CFG034(block_id) (0x0000000000000088ull)
+#define CVMX_PCIERCX_CFG035(block_id) (0x000000000000008Cull)
+#define CVMX_PCIERCX_CFG040(block_id) (0x00000000000000A0ull)
+#define CVMX_PCIERCX_CFG066(block_id) (0x0000000000000108ull)
+#define CVMX_PCIERCX_CFG069(block_id) (0x0000000000000114ull)
+#define CVMX_PCIERCX_CFG070(block_id) (0x0000000000000118ull)
+#define CVMX_PCIERCX_CFG075(block_id) (0x000000000000012Cull)
+#define CVMX_PCIERCX_CFG448(block_id) (0x0000000000000700ull)
+#define CVMX_PCIERCX_CFG452(block_id) (0x0000000000000710ull)
+#define CVMX_PCIERCX_CFG455(block_id) (0x000000000000071Cull)
+#define CVMX_PCIERCX_CFG515(block_id) (0x000000000000080Cull)
+
+union cvmx_pciercx_cfg001 {
+	uint32_t u32;
+	struct cvmx_pciercx_cfg001_s {
+		__BITFIELD_FIELD(uint32_t dpe:1,
+		__BITFIELD_FIELD(uint32_t sse:1,
+		__BITFIELD_FIELD(uint32_t rma:1,
+		__BITFIELD_FIELD(uint32_t rta:1,
+		__BITFIELD_FIELD(uint32_t sta:1,
+		__BITFIELD_FIELD(uint32_t devt:2,
+		__BITFIELD_FIELD(uint32_t mdpe:1,
+		__BITFIELD_FIELD(uint32_t fbb:1,
+		__BITFIELD_FIELD(uint32_t reserved_22_22:1,
+		__BITFIELD_FIELD(uint32_t m66:1,
+		__BITFIELD_FIELD(uint32_t cl:1,
+		__BITFIELD_FIELD(uint32_t i_stat:1,
+		__BITFIELD_FIELD(uint32_t reserved_11_18:8,
+		__BITFIELD_FIELD(uint32_t i_dis:1,
+		__BITFIELD_FIELD(uint32_t fbbe:1,
+		__BITFIELD_FIELD(uint32_t see:1,
+		__BITFIELD_FIELD(uint32_t ids_wcc:1,
+		__BITFIELD_FIELD(uint32_t per:1,
+		__BITFIELD_FIELD(uint32_t vps:1,
+		__BITFIELD_FIELD(uint32_t mwice:1,
+		__BITFIELD_FIELD(uint32_t scse:1,
+		__BITFIELD_FIELD(uint32_t me:1,
+		__BITFIELD_FIELD(uint32_t msae:1,
+		__BITFIELD_FIELD(uint32_t isae:1,
+		;))))))))))))))))))))))))
+	} s;
+};
+
+union cvmx_pciercx_cfg006 {
+	uint32_t u32;
+	struct cvmx_pciercx_cfg006_s {
+		__BITFIELD_FIELD(uint32_t slt:8,
+		__BITFIELD_FIELD(uint32_t subbnum:8,
+		__BITFIELD_FIELD(uint32_t sbnum:8,
+		__BITFIELD_FIELD(uint32_t pbnum:8,
+		;))))
+	} s;
+};
+
+union cvmx_pciercx_cfg008 {
+	uint32_t u32;
+	struct cvmx_pciercx_cfg008_s {
+		__BITFIELD_FIELD(uint32_t ml_addr:12,
+		__BITFIELD_FIELD(uint32_t reserved_16_19:4,
+		__BITFIELD_FIELD(uint32_t mb_addr:12,
+		__BITFIELD_FIELD(uint32_t reserved_0_3:4,
+		;))))
+	} s;
+};
+
+union cvmx_pciercx_cfg009 {
+	uint32_t u32;
+	struct cvmx_pciercx_cfg009_s {
+		__BITFIELD_FIELD(uint32_t lmem_limit:12,
+		__BITFIELD_FIELD(uint32_t reserved_17_19:3,
+		__BITFIELD_FIELD(uint32_t mem64b:1,
+		__BITFIELD_FIELD(uint32_t lmem_base:12,
+		__BITFIELD_FIELD(uint32_t reserved_1_3:3,
+		__BITFIELD_FIELD(uint32_t mem64a:1,
+		;))))))
+	} s;
+};
+
+union cvmx_pciercx_cfg010 {
+	uint32_t u32;
+	struct cvmx_pciercx_cfg010_s {
+		uint32_t umem_base;
+	} s;
+};
+
+union cvmx_pciercx_cfg011 {
+	uint32_t u32;
+	struct cvmx_pciercx_cfg011_s {
+		uint32_t umem_limit;
+	} s;
+};
+
+union cvmx_pciercx_cfg030 {
+	uint32_t u32;
+	struct cvmx_pciercx_cfg030_s {
+		__BITFIELD_FIELD(uint32_t reserved_22_31:10,
+		__BITFIELD_FIELD(uint32_t tp:1,
+		__BITFIELD_FIELD(uint32_t ap_d:1,
+		__BITFIELD_FIELD(uint32_t ur_d:1,
+		__BITFIELD_FIELD(uint32_t fe_d:1,
+		__BITFIELD_FIELD(uint32_t nfe_d:1,
+		__BITFIELD_FIELD(uint32_t ce_d:1,
+		__BITFIELD_FIELD(uint32_t reserved_15_15:1,
+		__BITFIELD_FIELD(uint32_t mrrs:3,
+		__BITFIELD_FIELD(uint32_t ns_en:1,
+		__BITFIELD_FIELD(uint32_t ap_en:1,
+		__BITFIELD_FIELD(uint32_t pf_en:1,
+		__BITFIELD_FIELD(uint32_t etf_en:1,
+		__BITFIELD_FIELD(uint32_t mps:3,
+		__BITFIELD_FIELD(uint32_t ro_en:1,
+		__BITFIELD_FIELD(uint32_t ur_en:1,
+		__BITFIELD_FIELD(uint32_t fe_en:1,
+		__BITFIELD_FIELD(uint32_t nfe_en:1,
+		__BITFIELD_FIELD(uint32_t ce_en:1,
+		;)))))))))))))))))))
+	} s;
+};
+
+union cvmx_pciercx_cfg031 {
+	uint32_t u32;
+	struct cvmx_pciercx_cfg031_s {
+		__BITFIELD_FIELD(uint32_t pnum:8,
+		__BITFIELD_FIELD(uint32_t reserved_23_23:1,
+		__BITFIELD_FIELD(uint32_t aspm:1,
+		__BITFIELD_FIELD(uint32_t lbnc:1,
+		__BITFIELD_FIELD(uint32_t dllarc:1,
+		__BITFIELD_FIELD(uint32_t sderc:1,
+		__BITFIELD_FIELD(uint32_t cpm:1,
+		__BITFIELD_FIELD(uint32_t l1el:3,
+		__BITFIELD_FIELD(uint32_t l0el:3,
+		__BITFIELD_FIELD(uint32_t aslpms:2,
+		__BITFIELD_FIELD(uint32_t mlw:6,
+		__BITFIELD_FIELD(uint32_t mls:4,
+		;))))))))))))
+	} s;
+};
+
+union cvmx_pciercx_cfg032 {
+	uint32_t u32;
+	struct cvmx_pciercx_cfg032_s {
+		__BITFIELD_FIELD(uint32_t lab:1,
+		__BITFIELD_FIELD(uint32_t lbm:1,
+		__BITFIELD_FIELD(uint32_t dlla:1,
+		__BITFIELD_FIELD(uint32_t scc:1,
+		__BITFIELD_FIELD(uint32_t lt:1,
+		__BITFIELD_FIELD(uint32_t reserved_26_26:1,
+		__BITFIELD_FIELD(uint32_t nlw:6,
+		__BITFIELD_FIELD(uint32_t ls:4,
+		__BITFIELD_FIELD(uint32_t reserved_12_15:4,
+		__BITFIELD_FIELD(uint32_t lab_int_enb:1,
+		__BITFIELD_FIELD(uint32_t lbm_int_enb:1,
+		__BITFIELD_FIELD(uint32_t hawd:1,
+		__BITFIELD_FIELD(uint32_t ecpm:1,
+		__BITFIELD_FIELD(uint32_t es:1,
+		__BITFIELD_FIELD(uint32_t ccc:1,
+		__BITFIELD_FIELD(uint32_t rl:1,
+		__BITFIELD_FIELD(uint32_t ld:1,
+		__BITFIELD_FIELD(uint32_t rcb:1,
+		__BITFIELD_FIELD(uint32_t reserved_2_2:1,
+		__BITFIELD_FIELD(uint32_t aslpc:2,
+		;))))))))))))))))))))
+	} s;
+};
+
+union cvmx_pciercx_cfg034 {
+	uint32_t u32;
+	struct cvmx_pciercx_cfg034_s {
+		__BITFIELD_FIELD(uint32_t reserved_25_31:7,
+		__BITFIELD_FIELD(uint32_t dlls_c:1,
+		__BITFIELD_FIELD(uint32_t emis:1,
+		__BITFIELD_FIELD(uint32_t pds:1,
+		__BITFIELD_FIELD(uint32_t mrlss:1,
+		__BITFIELD_FIELD(uint32_t ccint_d:1,
+		__BITFIELD_FIELD(uint32_t pd_c:1,
+		__BITFIELD_FIELD(uint32_t mrls_c:1,
+		__BITFIELD_FIELD(uint32_t pf_d:1,
+		__BITFIELD_FIELD(uint32_t abp_d:1,
+		__BITFIELD_FIELD(uint32_t reserved_13_15:3,
+		__BITFIELD_FIELD(uint32_t dlls_en:1,
+		__BITFIELD_FIELD(uint32_t emic:1,
+		__BITFIELD_FIELD(uint32_t pcc:1,
+		__BITFIELD_FIELD(uint32_t pic:1,
+		__BITFIELD_FIELD(uint32_t aic:1,
+		__BITFIELD_FIELD(uint32_t hpint_en:1,
+		__BITFIELD_FIELD(uint32_t ccint_en:1,
+		__BITFIELD_FIELD(uint32_t pd_en:1,
+		__BITFIELD_FIELD(uint32_t mrls_en:1,
+		__BITFIELD_FIELD(uint32_t pf_en:1,
+		__BITFIELD_FIELD(uint32_t abp_en:1,
+		;))))))))))))))))))))))
+	} s;
+};
+
+union cvmx_pciercx_cfg035 {
+	uint32_t u32;
+	struct cvmx_pciercx_cfg035_s {
+		__BITFIELD_FIELD(uint32_t reserved_17_31:15,
+		__BITFIELD_FIELD(uint32_t crssv:1,
+		__BITFIELD_FIELD(uint32_t reserved_5_15:11,
+		__BITFIELD_FIELD(uint32_t crssve:1,
+		__BITFIELD_FIELD(uint32_t pmeie:1,
+		__BITFIELD_FIELD(uint32_t sefee:1,
+		__BITFIELD_FIELD(uint32_t senfee:1,
+		__BITFIELD_FIELD(uint32_t secee:1,
+		;))))))))
+	} s;
+};
+
+union cvmx_pciercx_cfg040 {
+	uint32_t u32;
+	struct cvmx_pciercx_cfg040_s {
+		__BITFIELD_FIELD(uint32_t reserved_22_31:10,
+		__BITFIELD_FIELD(uint32_t ler:1,
+		__BITFIELD_FIELD(uint32_t ep3s:1,
+		__BITFIELD_FIELD(uint32_t ep2s:1,
+		__BITFIELD_FIELD(uint32_t ep1s:1,
+		__BITFIELD_FIELD(uint32_t eqc:1,
+		__BITFIELD_FIELD(uint32_t cdl:1,
+		__BITFIELD_FIELD(uint32_t cde:4,
+		__BITFIELD_FIELD(uint32_t csos:1,
+		__BITFIELD_FIELD(uint32_t emc:1,
+		__BITFIELD_FIELD(uint32_t tm:3,
+		__BITFIELD_FIELD(uint32_t sde:1,
+		__BITFIELD_FIELD(uint32_t hasd:1,
+		__BITFIELD_FIELD(uint32_t ec:1,
+		__BITFIELD_FIELD(uint32_t tls:4,
+		;)))))))))))))))
+	} s;
+};
+
+union cvmx_pciercx_cfg070 {
+	uint32_t u32;
+	struct cvmx_pciercx_cfg070_s {
+		__BITFIELD_FIELD(uint32_t reserved_12_31:20,
+		__BITFIELD_FIELD(uint32_t tplp:1,
+		__BITFIELD_FIELD(uint32_t reserved_9_10:2,
+		__BITFIELD_FIELD(uint32_t ce:1,
+		__BITFIELD_FIELD(uint32_t cc:1,
+		__BITFIELD_FIELD(uint32_t ge:1,
+		__BITFIELD_FIELD(uint32_t gc:1,
+		__BITFIELD_FIELD(uint32_t fep:5,
+		;))))))))
+	} s;
+};
+
+union cvmx_pciercx_cfg075 {
+	uint32_t u32;
+	struct cvmx_pciercx_cfg075_s {
+		__BITFIELD_FIELD(uint32_t reserved_3_31:29,
+		__BITFIELD_FIELD(uint32_t fere:1,
+		__BITFIELD_FIELD(uint32_t nfere:1,
+		__BITFIELD_FIELD(uint32_t cere:1,
+		;))))
+	} s;
+};
+
+union cvmx_pciercx_cfg448 {
+	uint32_t u32;
+	struct cvmx_pciercx_cfg448_s {
+		__BITFIELD_FIELD(uint32_t rtl:16,
+		__BITFIELD_FIELD(uint32_t rtltl:16,
+		;))
+	} s;
+};
+
+union cvmx_pciercx_cfg452 {
+	uint32_t u32;
+	struct cvmx_pciercx_cfg452_s {
+		__BITFIELD_FIELD(uint32_t reserved_26_31:6,
+		__BITFIELD_FIELD(uint32_t eccrc:1,
+		__BITFIELD_FIELD(uint32_t reserved_22_24:3,
+		__BITFIELD_FIELD(uint32_t lme:6,
+		__BITFIELD_FIELD(uint32_t reserved_12_15:4,
+		__BITFIELD_FIELD(uint32_t link_rate:4,
+		__BITFIELD_FIELD(uint32_t flm:1,
+		__BITFIELD_FIELD(uint32_t reserved_6_6:1,
+		__BITFIELD_FIELD(uint32_t dllle:1,
+		__BITFIELD_FIELD(uint32_t reserved_4_4:1,
+		__BITFIELD_FIELD(uint32_t ra:1,
+		__BITFIELD_FIELD(uint32_t le:1,
+		__BITFIELD_FIELD(uint32_t sd:1,
+		__BITFIELD_FIELD(uint32_t omr:1,
+		;))))))))))))))
+	} s;
+};
+
+union cvmx_pciercx_cfg455 {
+	uint32_t u32;
+	struct cvmx_pciercx_cfg455_s {
+		__BITFIELD_FIELD(uint32_t m_cfg0_filt:1,
+		__BITFIELD_FIELD(uint32_t m_io_filt:1,
+		__BITFIELD_FIELD(uint32_t msg_ctrl:1,
+		__BITFIELD_FIELD(uint32_t m_cpl_ecrc_filt:1,
+		__BITFIELD_FIELD(uint32_t m_ecrc_filt:1,
+		__BITFIELD_FIELD(uint32_t m_cpl_len_err:1,
+		__BITFIELD_FIELD(uint32_t m_cpl_attr_err:1,
+		__BITFIELD_FIELD(uint32_t m_cpl_tc_err:1,
+		__BITFIELD_FIELD(uint32_t m_cpl_fun_err:1,
+		__BITFIELD_FIELD(uint32_t m_cpl_rid_err:1,
+		__BITFIELD_FIELD(uint32_t m_cpl_tag_err:1,
+		__BITFIELD_FIELD(uint32_t m_lk_filt:1,
+		__BITFIELD_FIELD(uint32_t m_cfg1_filt:1,
+		__BITFIELD_FIELD(uint32_t m_bar_match:1,
+		__BITFIELD_FIELD(uint32_t m_pois_filt:1,
+		__BITFIELD_FIELD(uint32_t m_fun:1,
+		__BITFIELD_FIELD(uint32_t dfcwt:1,
+		__BITFIELD_FIELD(uint32_t reserved_11_14:4,
+		__BITFIELD_FIELD(uint32_t skpiv:11,
+		;)))))))))))))))))))
+	} s;
+};
+
+union cvmx_pciercx_cfg515 {
+	uint32_t u32;
+	struct cvmx_pciercx_cfg515_s {
+		__BITFIELD_FIELD(uint32_t reserved_21_31:11,
+		__BITFIELD_FIELD(uint32_t s_d_e:1,
+		__BITFIELD_FIELD(uint32_t ctcrb:1,
+		__BITFIELD_FIELD(uint32_t cpyts:1,
+		__BITFIELD_FIELD(uint32_t dsc:1,
+		__BITFIELD_FIELD(uint32_t le:9,
+		__BITFIELD_FIELD(uint32_t n_fts:8,
+		;)))))))
+	} s;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-pcsx-defs.h b/arch/mips/include/asm/octeon/cvmx-pcsx-defs.h
new file mode 100644
index 000000000..5f013269a
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-pcsx-defs.h
@@ -0,0 +1,826 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (C) 2003-2018 Cavium, Inc.
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_PCSX_DEFS_H__
+#define __CVMX_PCSX_DEFS_H__
+
+static inline uint64_t CVMX_PCSX_ANX_ADV_REG(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CNF71XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001010ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001010ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001010ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001010ull) + ((offset) + (block_id) * 0x4000ull) * 1024;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0001010ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+}
+
+static inline uint64_t CVMX_PCSX_ANX_EXT_ST_REG(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CNF71XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001028ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001028ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001028ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001028ull) + ((offset) + (block_id) * 0x4000ull) * 1024;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0001028ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+}
+
+static inline uint64_t CVMX_PCSX_ANX_LP_ABIL_REG(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CNF71XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001018ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001018ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001018ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001018ull) + ((offset) + (block_id) * 0x4000ull) * 1024;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0001018ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+}
+
+static inline uint64_t CVMX_PCSX_ANX_RESULTS_REG(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CNF71XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001020ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001020ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001020ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001020ull) + ((offset) + (block_id) * 0x4000ull) * 1024;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0001020ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+}
+
+static inline uint64_t CVMX_PCSX_INTX_EN_REG(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CNF71XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001088ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001088ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001088ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001088ull) + ((offset) + (block_id) * 0x4000ull) * 1024;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0001088ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+}
+
+static inline uint64_t CVMX_PCSX_INTX_REG(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CNF71XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001080ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001080ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001080ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001080ull) + ((offset) + (block_id) * 0x4000ull) * 1024;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0001080ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+}
+
+static inline uint64_t CVMX_PCSX_LINKX_TIMER_COUNT_REG(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CNF71XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001040ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001040ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001040ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001040ull) + ((offset) + (block_id) * 0x4000ull) * 1024;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0001040ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+}
+
+static inline uint64_t CVMX_PCSX_LOG_ANLX_REG(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CNF71XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001090ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001090ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001090ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001090ull) + ((offset) + (block_id) * 0x4000ull) * 1024;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0001090ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+}
+
+static inline uint64_t CVMX_PCSX_MISCX_CTL_REG(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CNF71XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001078ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001078ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001078ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001078ull) + ((offset) + (block_id) * 0x4000ull) * 1024;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0001078ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+}
+
+static inline uint64_t CVMX_PCSX_MRX_CONTROL_REG(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CNF71XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001000ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001000ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001000ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001000ull) + ((offset) + (block_id) * 0x4000ull) * 1024;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0001000ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+}
+
+static inline uint64_t CVMX_PCSX_MRX_STATUS_REG(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CNF71XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001008ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001008ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001008ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001008ull) + ((offset) + (block_id) * 0x4000ull) * 1024;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0001008ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+}
+
+static inline uint64_t CVMX_PCSX_RXX_STATES_REG(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CNF71XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001058ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001058ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001058ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001058ull) + ((offset) + (block_id) * 0x4000ull) * 1024;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0001058ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+}
+
+static inline uint64_t CVMX_PCSX_RXX_SYNC_REG(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CNF71XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001050ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001050ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001050ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001050ull) + ((offset) + (block_id) * 0x4000ull) * 1024;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0001050ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+}
+
+static inline uint64_t CVMX_PCSX_SGMX_AN_ADV_REG(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CNF71XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001068ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001068ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001068ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001068ull) + ((offset) + (block_id) * 0x4000ull) * 1024;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0001068ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+}
+
+static inline uint64_t CVMX_PCSX_SGMX_LP_ADV_REG(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CNF71XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001070ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001070ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001070ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001070ull) + ((offset) + (block_id) * 0x4000ull) * 1024;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0001070ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+}
+
+static inline uint64_t CVMX_PCSX_TXX_STATES_REG(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CNF71XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001060ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001060ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001060ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001060ull) + ((offset) + (block_id) * 0x4000ull) * 1024;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0001060ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+}
+
+static inline uint64_t CVMX_PCSX_TX_RXX_POLARITY_REG(unsigned long offset, unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CNF71XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001048ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001048ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001048ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0001048ull) + ((offset) + (block_id) * 0x4000ull) * 1024;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0001048ull) + ((offset) + (block_id) * 0x20000ull) * 1024;
+}
+
+void __cvmx_interrupt_pcsx_intx_en_reg_enable(int index, int block);
+
+union cvmx_pcsx_anx_adv_reg {
+	uint64_t u64;
+	struct cvmx_pcsx_anx_adv_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t np:1;
+		uint64_t reserved_14_14:1;
+		uint64_t rem_flt:2;
+		uint64_t reserved_9_11:3;
+		uint64_t pause:2;
+		uint64_t hfd:1;
+		uint64_t fd:1;
+		uint64_t reserved_0_4:5;
+#else
+		uint64_t reserved_0_4:5;
+		uint64_t fd:1;
+		uint64_t hfd:1;
+		uint64_t pause:2;
+		uint64_t reserved_9_11:3;
+		uint64_t rem_flt:2;
+		uint64_t reserved_14_14:1;
+		uint64_t np:1;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_pcsx_anx_ext_st_reg {
+	uint64_t u64;
+	struct cvmx_pcsx_anx_ext_st_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t thou_xfd:1;
+		uint64_t thou_xhd:1;
+		uint64_t thou_tfd:1;
+		uint64_t thou_thd:1;
+		uint64_t reserved_0_11:12;
+#else
+		uint64_t reserved_0_11:12;
+		uint64_t thou_thd:1;
+		uint64_t thou_tfd:1;
+		uint64_t thou_xhd:1;
+		uint64_t thou_xfd:1;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_pcsx_anx_lp_abil_reg {
+	uint64_t u64;
+	struct cvmx_pcsx_anx_lp_abil_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t np:1;
+		uint64_t ack:1;
+		uint64_t rem_flt:2;
+		uint64_t reserved_9_11:3;
+		uint64_t pause:2;
+		uint64_t hfd:1;
+		uint64_t fd:1;
+		uint64_t reserved_0_4:5;
+#else
+		uint64_t reserved_0_4:5;
+		uint64_t fd:1;
+		uint64_t hfd:1;
+		uint64_t pause:2;
+		uint64_t reserved_9_11:3;
+		uint64_t rem_flt:2;
+		uint64_t ack:1;
+		uint64_t np:1;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_pcsx_anx_results_reg {
+	uint64_t u64;
+	struct cvmx_pcsx_anx_results_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t pause:2;
+		uint64_t spd:2;
+		uint64_t an_cpt:1;
+		uint64_t dup:1;
+		uint64_t link_ok:1;
+#else
+		uint64_t link_ok:1;
+		uint64_t dup:1;
+		uint64_t an_cpt:1;
+		uint64_t spd:2;
+		uint64_t pause:2;
+		uint64_t reserved_7_63:57;
+#endif
+	} s;
+};
+
+union cvmx_pcsx_intx_en_reg {
+	uint64_t u64;
+	struct cvmx_pcsx_intx_en_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_13_63:51;
+		uint64_t dbg_sync_en:1;
+		uint64_t dup:1;
+		uint64_t sync_bad_en:1;
+		uint64_t an_bad_en:1;
+		uint64_t rxlock_en:1;
+		uint64_t rxbad_en:1;
+		uint64_t rxerr_en:1;
+		uint64_t txbad_en:1;
+		uint64_t txfifo_en:1;
+		uint64_t txfifu_en:1;
+		uint64_t an_err_en:1;
+		uint64_t xmit_en:1;
+		uint64_t lnkspd_en:1;
+#else
+		uint64_t lnkspd_en:1;
+		uint64_t xmit_en:1;
+		uint64_t an_err_en:1;
+		uint64_t txfifu_en:1;
+		uint64_t txfifo_en:1;
+		uint64_t txbad_en:1;
+		uint64_t rxerr_en:1;
+		uint64_t rxbad_en:1;
+		uint64_t rxlock_en:1;
+		uint64_t an_bad_en:1;
+		uint64_t sync_bad_en:1;
+		uint64_t dup:1;
+		uint64_t dbg_sync_en:1;
+		uint64_t reserved_13_63:51;
+#endif
+	} s;
+	struct cvmx_pcsx_intx_en_reg_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t dup:1;
+		uint64_t sync_bad_en:1;
+		uint64_t an_bad_en:1;
+		uint64_t rxlock_en:1;
+		uint64_t rxbad_en:1;
+		uint64_t rxerr_en:1;
+		uint64_t txbad_en:1;
+		uint64_t txfifo_en:1;
+		uint64_t txfifu_en:1;
+		uint64_t an_err_en:1;
+		uint64_t xmit_en:1;
+		uint64_t lnkspd_en:1;
+#else
+		uint64_t lnkspd_en:1;
+		uint64_t xmit_en:1;
+		uint64_t an_err_en:1;
+		uint64_t txfifu_en:1;
+		uint64_t txfifo_en:1;
+		uint64_t txbad_en:1;
+		uint64_t rxerr_en:1;
+		uint64_t rxbad_en:1;
+		uint64_t rxlock_en:1;
+		uint64_t an_bad_en:1;
+		uint64_t sync_bad_en:1;
+		uint64_t dup:1;
+		uint64_t reserved_12_63:52;
+#endif
+	} cn52xx;
+};
+
+union cvmx_pcsx_intx_reg {
+	uint64_t u64;
+	struct cvmx_pcsx_intx_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_13_63:51;
+		uint64_t dbg_sync:1;
+		uint64_t dup:1;
+		uint64_t sync_bad:1;
+		uint64_t an_bad:1;
+		uint64_t rxlock:1;
+		uint64_t rxbad:1;
+		uint64_t rxerr:1;
+		uint64_t txbad:1;
+		uint64_t txfifo:1;
+		uint64_t txfifu:1;
+		uint64_t an_err:1;
+		uint64_t xmit:1;
+		uint64_t lnkspd:1;
+#else
+		uint64_t lnkspd:1;
+		uint64_t xmit:1;
+		uint64_t an_err:1;
+		uint64_t txfifu:1;
+		uint64_t txfifo:1;
+		uint64_t txbad:1;
+		uint64_t rxerr:1;
+		uint64_t rxbad:1;
+		uint64_t rxlock:1;
+		uint64_t an_bad:1;
+		uint64_t sync_bad:1;
+		uint64_t dup:1;
+		uint64_t dbg_sync:1;
+		uint64_t reserved_13_63:51;
+#endif
+	} s;
+	struct cvmx_pcsx_intx_reg_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t dup:1;
+		uint64_t sync_bad:1;
+		uint64_t an_bad:1;
+		uint64_t rxlock:1;
+		uint64_t rxbad:1;
+		uint64_t rxerr:1;
+		uint64_t txbad:1;
+		uint64_t txfifo:1;
+		uint64_t txfifu:1;
+		uint64_t an_err:1;
+		uint64_t xmit:1;
+		uint64_t lnkspd:1;
+#else
+		uint64_t lnkspd:1;
+		uint64_t xmit:1;
+		uint64_t an_err:1;
+		uint64_t txfifu:1;
+		uint64_t txfifo:1;
+		uint64_t txbad:1;
+		uint64_t rxerr:1;
+		uint64_t rxbad:1;
+		uint64_t rxlock:1;
+		uint64_t an_bad:1;
+		uint64_t sync_bad:1;
+		uint64_t dup:1;
+		uint64_t reserved_12_63:52;
+#endif
+	} cn52xx;
+};
+
+union cvmx_pcsx_linkx_timer_count_reg {
+	uint64_t u64;
+	struct cvmx_pcsx_linkx_timer_count_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t count:16;
+#else
+		uint64_t count:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_pcsx_log_anlx_reg {
+	uint64_t u64;
+	struct cvmx_pcsx_log_anlx_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t lafifovfl:1;
+		uint64_t la_en:1;
+		uint64_t pkt_sz:2;
+#else
+		uint64_t pkt_sz:2;
+		uint64_t la_en:1;
+		uint64_t lafifovfl:1;
+		uint64_t reserved_4_63:60;
+#endif
+	} s;
+};
+
+union cvmx_pcsx_miscx_ctl_reg {
+	uint64_t u64;
+	struct cvmx_pcsx_miscx_ctl_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_13_63:51;
+		uint64_t sgmii:1;
+		uint64_t gmxeno:1;
+		uint64_t loopbck2:1;
+		uint64_t mac_phy:1;
+		uint64_t mode:1;
+		uint64_t an_ovrd:1;
+		uint64_t samp_pt:7;
+#else
+		uint64_t samp_pt:7;
+		uint64_t an_ovrd:1;
+		uint64_t mode:1;
+		uint64_t mac_phy:1;
+		uint64_t loopbck2:1;
+		uint64_t gmxeno:1;
+		uint64_t sgmii:1;
+		uint64_t reserved_13_63:51;
+#endif
+	} s;
+};
+
+union cvmx_pcsx_mrx_control_reg {
+	uint64_t u64;
+	struct cvmx_pcsx_mrx_control_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t reset:1;
+		uint64_t loopbck1:1;
+		uint64_t spdlsb:1;
+		uint64_t an_en:1;
+		uint64_t pwr_dn:1;
+		uint64_t reserved_10_10:1;
+		uint64_t rst_an:1;
+		uint64_t dup:1;
+		uint64_t coltst:1;
+		uint64_t spdmsb:1;
+		uint64_t uni:1;
+		uint64_t reserved_0_4:5;
+#else
+		uint64_t reserved_0_4:5;
+		uint64_t uni:1;
+		uint64_t spdmsb:1;
+		uint64_t coltst:1;
+		uint64_t dup:1;
+		uint64_t rst_an:1;
+		uint64_t reserved_10_10:1;
+		uint64_t pwr_dn:1;
+		uint64_t an_en:1;
+		uint64_t spdlsb:1;
+		uint64_t loopbck1:1;
+		uint64_t reset:1;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_pcsx_mrx_status_reg {
+	uint64_t u64;
+	struct cvmx_pcsx_mrx_status_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t hun_t4:1;
+		uint64_t hun_xfd:1;
+		uint64_t hun_xhd:1;
+		uint64_t ten_fd:1;
+		uint64_t ten_hd:1;
+		uint64_t hun_t2fd:1;
+		uint64_t hun_t2hd:1;
+		uint64_t ext_st:1;
+		uint64_t reserved_7_7:1;
+		uint64_t prb_sup:1;
+		uint64_t an_cpt:1;
+		uint64_t rm_flt:1;
+		uint64_t an_abil:1;
+		uint64_t lnk_st:1;
+		uint64_t reserved_1_1:1;
+		uint64_t extnd:1;
+#else
+		uint64_t extnd:1;
+		uint64_t reserved_1_1:1;
+		uint64_t lnk_st:1;
+		uint64_t an_abil:1;
+		uint64_t rm_flt:1;
+		uint64_t an_cpt:1;
+		uint64_t prb_sup:1;
+		uint64_t reserved_7_7:1;
+		uint64_t ext_st:1;
+		uint64_t hun_t2hd:1;
+		uint64_t hun_t2fd:1;
+		uint64_t ten_hd:1;
+		uint64_t ten_fd:1;
+		uint64_t hun_xhd:1;
+		uint64_t hun_xfd:1;
+		uint64_t hun_t4:1;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_pcsx_rxx_states_reg {
+	uint64_t u64;
+	struct cvmx_pcsx_rxx_states_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t rx_bad:1;
+		uint64_t rx_st:5;
+		uint64_t sync_bad:1;
+		uint64_t sync:4;
+		uint64_t an_bad:1;
+		uint64_t an_st:4;
+#else
+		uint64_t an_st:4;
+		uint64_t an_bad:1;
+		uint64_t sync:4;
+		uint64_t sync_bad:1;
+		uint64_t rx_st:5;
+		uint64_t rx_bad:1;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_pcsx_rxx_sync_reg {
+	uint64_t u64;
+	struct cvmx_pcsx_rxx_sync_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t sync:1;
+		uint64_t bit_lock:1;
+#else
+		uint64_t bit_lock:1;
+		uint64_t sync:1;
+		uint64_t reserved_2_63:62;
+#endif
+	} s;
+};
+
+union cvmx_pcsx_sgmx_an_adv_reg {
+	uint64_t u64;
+	struct cvmx_pcsx_sgmx_an_adv_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t link:1;
+		uint64_t ack:1;
+		uint64_t reserved_13_13:1;
+		uint64_t dup:1;
+		uint64_t speed:2;
+		uint64_t reserved_1_9:9;
+		uint64_t one:1;
+#else
+		uint64_t one:1;
+		uint64_t reserved_1_9:9;
+		uint64_t speed:2;
+		uint64_t dup:1;
+		uint64_t reserved_13_13:1;
+		uint64_t ack:1;
+		uint64_t link:1;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_pcsx_sgmx_lp_adv_reg {
+	uint64_t u64;
+	struct cvmx_pcsx_sgmx_lp_adv_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t link:1;
+		uint64_t reserved_13_14:2;
+		uint64_t dup:1;
+		uint64_t speed:2;
+		uint64_t reserved_1_9:9;
+		uint64_t one:1;
+#else
+		uint64_t one:1;
+		uint64_t reserved_1_9:9;
+		uint64_t speed:2;
+		uint64_t dup:1;
+		uint64_t reserved_13_14:2;
+		uint64_t link:1;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_pcsx_txx_states_reg {
+	uint64_t u64;
+	struct cvmx_pcsx_txx_states_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t xmit:2;
+		uint64_t tx_bad:1;
+		uint64_t ord_st:4;
+#else
+		uint64_t ord_st:4;
+		uint64_t tx_bad:1;
+		uint64_t xmit:2;
+		uint64_t reserved_7_63:57;
+#endif
+	} s;
+};
+
+union cvmx_pcsx_tx_rxx_polarity_reg {
+	uint64_t u64;
+	struct cvmx_pcsx_tx_rxx_polarity_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t rxovrd:1;
+		uint64_t autorxpl:1;
+		uint64_t rxplrt:1;
+		uint64_t txplrt:1;
+#else
+		uint64_t txplrt:1;
+		uint64_t rxplrt:1;
+		uint64_t autorxpl:1;
+		uint64_t rxovrd:1;
+		uint64_t reserved_4_63:60;
+#endif
+	} s;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-pcsxx-defs.h b/arch/mips/include/asm/octeon/cvmx-pcsxx-defs.h
new file mode 100644
index 000000000..b353775ee
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-pcsxx-defs.h
@@ -0,0 +1,664 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (C) 2003-2018 Cavium, Inc.
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_PCSXX_DEFS_H__
+#define __CVMX_PCSXX_DEFS_H__
+
+static inline uint64_t CVMX_PCSXX_10GBX_STATUS_REG(unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000828ull) + (block_id) * 0x8000000ull;
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000828ull) + (block_id) * 0x8000000ull;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000828ull) + (block_id) * 0x1000000ull;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0000828ull) + (block_id) * 0x1000000ull;
+}
+
+static inline uint64_t CVMX_PCSXX_BIST_STATUS_REG(unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000870ull) + (block_id) * 0x8000000ull;
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000870ull) + (block_id) * 0x8000000ull;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000870ull) + (block_id) * 0x1000000ull;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0000870ull) + (block_id) * 0x1000000ull;
+}
+
+static inline uint64_t CVMX_PCSXX_BIT_LOCK_STATUS_REG(unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000850ull) + (block_id) * 0x8000000ull;
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000850ull) + (block_id) * 0x8000000ull;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000850ull) + (block_id) * 0x1000000ull;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0000850ull) + (block_id) * 0x1000000ull;
+}
+
+static inline uint64_t CVMX_PCSXX_CONTROL1_REG(unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000800ull) + (block_id) * 0x8000000ull;
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000800ull) + (block_id) * 0x8000000ull;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000800ull) + (block_id) * 0x1000000ull;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0000800ull) + (block_id) * 0x1000000ull;
+}
+
+static inline uint64_t CVMX_PCSXX_CONTROL2_REG(unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000818ull) + (block_id) * 0x8000000ull;
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000818ull) + (block_id) * 0x8000000ull;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000818ull) + (block_id) * 0x1000000ull;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0000818ull) + (block_id) * 0x1000000ull;
+}
+
+static inline uint64_t CVMX_PCSXX_INT_EN_REG(unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000860ull) + (block_id) * 0x8000000ull;
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000860ull) + (block_id) * 0x8000000ull;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000860ull) + (block_id) * 0x1000000ull;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0000860ull) + (block_id) * 0x1000000ull;
+}
+
+static inline uint64_t CVMX_PCSXX_INT_REG(unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000858ull) + (block_id) * 0x8000000ull;
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000858ull) + (block_id) * 0x8000000ull;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000858ull) + (block_id) * 0x1000000ull;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0000858ull) + (block_id) * 0x1000000ull;
+}
+
+static inline uint64_t CVMX_PCSXX_LOG_ANL_REG(unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000868ull) + (block_id) * 0x8000000ull;
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000868ull) + (block_id) * 0x8000000ull;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000868ull) + (block_id) * 0x1000000ull;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0000868ull) + (block_id) * 0x1000000ull;
+}
+
+static inline uint64_t CVMX_PCSXX_MISC_CTL_REG(unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000848ull) + (block_id) * 0x8000000ull;
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000848ull) + (block_id) * 0x8000000ull;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000848ull) + (block_id) * 0x1000000ull;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0000848ull) + (block_id) * 0x1000000ull;
+}
+
+static inline uint64_t CVMX_PCSXX_RX_SYNC_STATES_REG(unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000838ull) + (block_id) * 0x8000000ull;
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000838ull) + (block_id) * 0x8000000ull;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000838ull) + (block_id) * 0x1000000ull;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0000838ull) + (block_id) * 0x1000000ull;
+}
+
+static inline uint64_t CVMX_PCSXX_SPD_ABIL_REG(unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000810ull) + (block_id) * 0x8000000ull;
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000810ull) + (block_id) * 0x8000000ull;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000810ull) + (block_id) * 0x1000000ull;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0000810ull) + (block_id) * 0x1000000ull;
+}
+
+static inline uint64_t CVMX_PCSXX_STATUS1_REG(unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000808ull) + (block_id) * 0x8000000ull;
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000808ull) + (block_id) * 0x8000000ull;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000808ull) + (block_id) * 0x1000000ull;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0000808ull) + (block_id) * 0x1000000ull;
+}
+
+static inline uint64_t CVMX_PCSXX_STATUS2_REG(unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000820ull) + (block_id) * 0x8000000ull;
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000820ull) + (block_id) * 0x8000000ull;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000820ull) + (block_id) * 0x1000000ull;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0000820ull) + (block_id) * 0x1000000ull;
+}
+
+static inline uint64_t CVMX_PCSXX_TX_RX_POLARITY_REG(unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000840ull) + (block_id) * 0x8000000ull;
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000840ull) + (block_id) * 0x8000000ull;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000840ull) + (block_id) * 0x1000000ull;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0000840ull) + (block_id) * 0x1000000ull;
+}
+
+static inline uint64_t CVMX_PCSXX_TX_RX_STATES_REG(unsigned long block_id)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CN56XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000830ull) + (block_id) * 0x8000000ull;
+	case OCTEON_CN52XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000830ull) + (block_id) * 0x8000000ull;
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+		return CVMX_ADD_IO_SEG(0x00011800B0000830ull) + (block_id) * 0x1000000ull;
+	}
+	return CVMX_ADD_IO_SEG(0x00011800B0000830ull) + (block_id) * 0x1000000ull;
+}
+
+void __cvmx_interrupt_pcsxx_int_en_reg_enable(int index);
+
+union cvmx_pcsxx_10gbx_status_reg {
+	uint64_t u64;
+	struct cvmx_pcsxx_10gbx_status_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_13_63:51;
+		uint64_t alignd:1;
+		uint64_t pattst:1;
+		uint64_t reserved_4_10:7;
+		uint64_t l3sync:1;
+		uint64_t l2sync:1;
+		uint64_t l1sync:1;
+		uint64_t l0sync:1;
+#else
+		uint64_t l0sync:1;
+		uint64_t l1sync:1;
+		uint64_t l2sync:1;
+		uint64_t l3sync:1;
+		uint64_t reserved_4_10:7;
+		uint64_t pattst:1;
+		uint64_t alignd:1;
+		uint64_t reserved_13_63:51;
+#endif
+	} s;
+};
+
+union cvmx_pcsxx_bist_status_reg {
+	uint64_t u64;
+	struct cvmx_pcsxx_bist_status_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t bist_status:1;
+#else
+		uint64_t bist_status:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_pcsxx_bit_lock_status_reg {
+	uint64_t u64;
+	struct cvmx_pcsxx_bit_lock_status_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t bitlck3:1;
+		uint64_t bitlck2:1;
+		uint64_t bitlck1:1;
+		uint64_t bitlck0:1;
+#else
+		uint64_t bitlck0:1;
+		uint64_t bitlck1:1;
+		uint64_t bitlck2:1;
+		uint64_t bitlck3:1;
+		uint64_t reserved_4_63:60;
+#endif
+	} s;
+};
+
+union cvmx_pcsxx_control1_reg {
+	uint64_t u64;
+	struct cvmx_pcsxx_control1_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t reset:1;
+		uint64_t loopbck1:1;
+		uint64_t spdsel1:1;
+		uint64_t reserved_12_12:1;
+		uint64_t lo_pwr:1;
+		uint64_t reserved_7_10:4;
+		uint64_t spdsel0:1;
+		uint64_t spd:4;
+		uint64_t reserved_0_1:2;
+#else
+		uint64_t reserved_0_1:2;
+		uint64_t spd:4;
+		uint64_t spdsel0:1;
+		uint64_t reserved_7_10:4;
+		uint64_t lo_pwr:1;
+		uint64_t reserved_12_12:1;
+		uint64_t spdsel1:1;
+		uint64_t loopbck1:1;
+		uint64_t reset:1;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_pcsxx_control2_reg {
+	uint64_t u64;
+	struct cvmx_pcsxx_control2_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t type:2;
+#else
+		uint64_t type:2;
+		uint64_t reserved_2_63:62;
+#endif
+	} s;
+};
+
+union cvmx_pcsxx_int_en_reg {
+	uint64_t u64;
+	struct cvmx_pcsxx_int_en_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t dbg_sync_en:1;
+		uint64_t algnlos_en:1;
+		uint64_t synlos_en:1;
+		uint64_t bitlckls_en:1;
+		uint64_t rxsynbad_en:1;
+		uint64_t rxbad_en:1;
+		uint64_t txflt_en:1;
+#else
+		uint64_t txflt_en:1;
+		uint64_t rxbad_en:1;
+		uint64_t rxsynbad_en:1;
+		uint64_t bitlckls_en:1;
+		uint64_t synlos_en:1;
+		uint64_t algnlos_en:1;
+		uint64_t dbg_sync_en:1;
+		uint64_t reserved_7_63:57;
+#endif
+	} s;
+	struct cvmx_pcsxx_int_en_reg_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t algnlos_en:1;
+		uint64_t synlos_en:1;
+		uint64_t bitlckls_en:1;
+		uint64_t rxsynbad_en:1;
+		uint64_t rxbad_en:1;
+		uint64_t txflt_en:1;
+#else
+		uint64_t txflt_en:1;
+		uint64_t rxbad_en:1;
+		uint64_t rxsynbad_en:1;
+		uint64_t bitlckls_en:1;
+		uint64_t synlos_en:1;
+		uint64_t algnlos_en:1;
+		uint64_t reserved_6_63:58;
+#endif
+	} cn52xx;
+};
+
+union cvmx_pcsxx_int_reg {
+	uint64_t u64;
+	struct cvmx_pcsxx_int_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t dbg_sync:1;
+		uint64_t algnlos:1;
+		uint64_t synlos:1;
+		uint64_t bitlckls:1;
+		uint64_t rxsynbad:1;
+		uint64_t rxbad:1;
+		uint64_t txflt:1;
+#else
+		uint64_t txflt:1;
+		uint64_t rxbad:1;
+		uint64_t rxsynbad:1;
+		uint64_t bitlckls:1;
+		uint64_t synlos:1;
+		uint64_t algnlos:1;
+		uint64_t dbg_sync:1;
+		uint64_t reserved_7_63:57;
+#endif
+	} s;
+	struct cvmx_pcsxx_int_reg_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t algnlos:1;
+		uint64_t synlos:1;
+		uint64_t bitlckls:1;
+		uint64_t rxsynbad:1;
+		uint64_t rxbad:1;
+		uint64_t txflt:1;
+#else
+		uint64_t txflt:1;
+		uint64_t rxbad:1;
+		uint64_t rxsynbad:1;
+		uint64_t bitlckls:1;
+		uint64_t synlos:1;
+		uint64_t algnlos:1;
+		uint64_t reserved_6_63:58;
+#endif
+	} cn52xx;
+};
+
+union cvmx_pcsxx_log_anl_reg {
+	uint64_t u64;
+	struct cvmx_pcsxx_log_anl_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t enc_mode:1;
+		uint64_t drop_ln:2;
+		uint64_t lafifovfl:1;
+		uint64_t la_en:1;
+		uint64_t pkt_sz:2;
+#else
+		uint64_t pkt_sz:2;
+		uint64_t la_en:1;
+		uint64_t lafifovfl:1;
+		uint64_t drop_ln:2;
+		uint64_t enc_mode:1;
+		uint64_t reserved_7_63:57;
+#endif
+	} s;
+};
+
+union cvmx_pcsxx_misc_ctl_reg {
+	uint64_t u64;
+	struct cvmx_pcsxx_misc_ctl_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t tx_swap:1;
+		uint64_t rx_swap:1;
+		uint64_t xaui:1;
+		uint64_t gmxeno:1;
+#else
+		uint64_t gmxeno:1;
+		uint64_t xaui:1;
+		uint64_t rx_swap:1;
+		uint64_t tx_swap:1;
+		uint64_t reserved_4_63:60;
+#endif
+	} s;
+};
+
+union cvmx_pcsxx_rx_sync_states_reg {
+	uint64_t u64;
+	struct cvmx_pcsxx_rx_sync_states_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t sync3st:4;
+		uint64_t sync2st:4;
+		uint64_t sync1st:4;
+		uint64_t sync0st:4;
+#else
+		uint64_t sync0st:4;
+		uint64_t sync1st:4;
+		uint64_t sync2st:4;
+		uint64_t sync3st:4;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_pcsxx_spd_abil_reg {
+	uint64_t u64;
+	struct cvmx_pcsxx_spd_abil_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t tenpasst:1;
+		uint64_t tengb:1;
+#else
+		uint64_t tengb:1;
+		uint64_t tenpasst:1;
+		uint64_t reserved_2_63:62;
+#endif
+	} s;
+};
+
+union cvmx_pcsxx_status1_reg {
+	uint64_t u64;
+	struct cvmx_pcsxx_status1_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t flt:1;
+		uint64_t reserved_3_6:4;
+		uint64_t rcv_lnk:1;
+		uint64_t lpable:1;
+		uint64_t reserved_0_0:1;
+#else
+		uint64_t reserved_0_0:1;
+		uint64_t lpable:1;
+		uint64_t rcv_lnk:1;
+		uint64_t reserved_3_6:4;
+		uint64_t flt:1;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_pcsxx_status2_reg {
+	uint64_t u64;
+	struct cvmx_pcsxx_status2_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t dev:2;
+		uint64_t reserved_12_13:2;
+		uint64_t xmtflt:1;
+		uint64_t rcvflt:1;
+		uint64_t reserved_3_9:7;
+		uint64_t tengb_w:1;
+		uint64_t tengb_x:1;
+		uint64_t tengb_r:1;
+#else
+		uint64_t tengb_r:1;
+		uint64_t tengb_x:1;
+		uint64_t tengb_w:1;
+		uint64_t reserved_3_9:7;
+		uint64_t rcvflt:1;
+		uint64_t xmtflt:1;
+		uint64_t reserved_12_13:2;
+		uint64_t dev:2;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_pcsxx_tx_rx_polarity_reg {
+	uint64_t u64;
+	struct cvmx_pcsxx_tx_rx_polarity_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t xor_rxplrt:4;
+		uint64_t xor_txplrt:4;
+		uint64_t rxplrt:1;
+		uint64_t txplrt:1;
+#else
+		uint64_t txplrt:1;
+		uint64_t rxplrt:1;
+		uint64_t xor_txplrt:4;
+		uint64_t xor_rxplrt:4;
+		uint64_t reserved_10_63:54;
+#endif
+	} s;
+	struct cvmx_pcsxx_tx_rx_polarity_reg_cn52xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t rxplrt:1;
+		uint64_t txplrt:1;
+#else
+		uint64_t txplrt:1;
+		uint64_t rxplrt:1;
+		uint64_t reserved_2_63:62;
+#endif
+	} cn52xxp1;
+};
+
+union cvmx_pcsxx_tx_rx_states_reg {
+	uint64_t u64;
+	struct cvmx_pcsxx_tx_rx_states_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_14_63:50;
+		uint64_t term_err:1;
+		uint64_t syn3bad:1;
+		uint64_t syn2bad:1;
+		uint64_t syn1bad:1;
+		uint64_t syn0bad:1;
+		uint64_t rxbad:1;
+		uint64_t algn_st:3;
+		uint64_t rx_st:2;
+		uint64_t tx_st:3;
+#else
+		uint64_t tx_st:3;
+		uint64_t rx_st:2;
+		uint64_t algn_st:3;
+		uint64_t rxbad:1;
+		uint64_t syn0bad:1;
+		uint64_t syn1bad:1;
+		uint64_t syn2bad:1;
+		uint64_t syn3bad:1;
+		uint64_t term_err:1;
+		uint64_t reserved_14_63:50;
+#endif
+	} s;
+	struct cvmx_pcsxx_tx_rx_states_reg_cn52xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_13_63:51;
+		uint64_t syn3bad:1;
+		uint64_t syn2bad:1;
+		uint64_t syn1bad:1;
+		uint64_t syn0bad:1;
+		uint64_t rxbad:1;
+		uint64_t algn_st:3;
+		uint64_t rx_st:2;
+		uint64_t tx_st:3;
+#else
+		uint64_t tx_st:3;
+		uint64_t rx_st:2;
+		uint64_t algn_st:3;
+		uint64_t rxbad:1;
+		uint64_t syn0bad:1;
+		uint64_t syn1bad:1;
+		uint64_t syn2bad:1;
+		uint64_t syn3bad:1;
+		uint64_t reserved_13_63:51;
+#endif
+	} cn52xxp1;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-pemx-defs.h b/arch/mips/include/asm/octeon/cvmx-pemx-defs.h
new file mode 100644
index 000000000..d2d6dba93
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-pemx-defs.h
@@ -0,0 +1,651 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2012 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_PEMX_DEFS_H__
+#define __CVMX_PEMX_DEFS_H__
+
+#define CVMX_PEMX_BAR1_INDEXX(offset, block_id) (CVMX_ADD_IO_SEG(0x00011800C00000A8ull) + (((offset) & 15) + ((block_id) & 1) * 0x200000ull) * 8)
+#define CVMX_PEMX_BAR2_MASK(block_id) (CVMX_ADD_IO_SEG(0x00011800C0000130ull) + ((block_id) & 1) * 0x1000000ull)
+#define CVMX_PEMX_BAR_CTL(block_id) (CVMX_ADD_IO_SEG(0x00011800C0000128ull) + ((block_id) & 1) * 0x1000000ull)
+#define CVMX_PEMX_BIST_STATUS(block_id) (CVMX_ADD_IO_SEG(0x00011800C0000018ull) + ((block_id) & 1) * 0x1000000ull)
+#define CVMX_PEMX_BIST_STATUS2(block_id) (CVMX_ADD_IO_SEG(0x00011800C0000420ull) + ((block_id) & 1) * 0x1000000ull)
+#define CVMX_PEMX_CFG_RD(block_id) (CVMX_ADD_IO_SEG(0x00011800C0000030ull) + ((block_id) & 1) * 0x1000000ull)
+#define CVMX_PEMX_CFG_WR(block_id) (CVMX_ADD_IO_SEG(0x00011800C0000028ull) + ((block_id) & 1) * 0x1000000ull)
+#define CVMX_PEMX_CPL_LUT_VALID(block_id) (CVMX_ADD_IO_SEG(0x00011800C0000098ull) + ((block_id) & 1) * 0x1000000ull)
+#define CVMX_PEMX_CTL_STATUS(block_id) (CVMX_ADD_IO_SEG(0x00011800C0000000ull) + ((block_id) & 1) * 0x1000000ull)
+#define CVMX_PEMX_DBG_INFO(block_id) (CVMX_ADD_IO_SEG(0x00011800C0000008ull) + ((block_id) & 1) * 0x1000000ull)
+#define CVMX_PEMX_DBG_INFO_EN(block_id) (CVMX_ADD_IO_SEG(0x00011800C00000A0ull) + ((block_id) & 1) * 0x1000000ull)
+#define CVMX_PEMX_DIAG_STATUS(block_id) (CVMX_ADD_IO_SEG(0x00011800C0000020ull) + ((block_id) & 1) * 0x1000000ull)
+#define CVMX_PEMX_INB_READ_CREDITS(block_id) (CVMX_ADD_IO_SEG(0x00011800C0000138ull) + ((block_id) & 1) * 0x1000000ull)
+#define CVMX_PEMX_INT_ENB(block_id) (CVMX_ADD_IO_SEG(0x00011800C0000410ull) + ((block_id) & 1) * 0x1000000ull)
+#define CVMX_PEMX_INT_ENB_INT(block_id) (CVMX_ADD_IO_SEG(0x00011800C0000418ull) + ((block_id) & 1) * 0x1000000ull)
+#define CVMX_PEMX_INT_SUM(block_id) (CVMX_ADD_IO_SEG(0x00011800C0000408ull) + ((block_id) & 1) * 0x1000000ull)
+#define CVMX_PEMX_P2N_BAR0_START(block_id) (CVMX_ADD_IO_SEG(0x00011800C0000080ull) + ((block_id) & 1) * 0x1000000ull)
+#define CVMX_PEMX_P2N_BAR1_START(block_id) (CVMX_ADD_IO_SEG(0x00011800C0000088ull) + ((block_id) & 1) * 0x1000000ull)
+#define CVMX_PEMX_P2N_BAR2_START(block_id) (CVMX_ADD_IO_SEG(0x00011800C0000090ull) + ((block_id) & 1) * 0x1000000ull)
+#define CVMX_PEMX_P2P_BARX_END(offset, block_id) (CVMX_ADD_IO_SEG(0x00011800C0000048ull) + (((offset) & 3) + ((block_id) & 1) * 0x100000ull) * 16)
+#define CVMX_PEMX_P2P_BARX_START(offset, block_id) (CVMX_ADD_IO_SEG(0x00011800C0000040ull) + (((offset) & 3) + ((block_id) & 1) * 0x100000ull) * 16)
+#define CVMX_PEMX_TLP_CREDITS(block_id) (CVMX_ADD_IO_SEG(0x00011800C0000038ull) + ((block_id) & 1) * 0x1000000ull)
+
+union cvmx_pemx_bar1_indexx {
+	uint64_t u64;
+	struct cvmx_pemx_bar1_indexx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t addr_idx:16;
+		uint64_t ca:1;
+		uint64_t end_swp:2;
+		uint64_t addr_v:1;
+#else
+		uint64_t addr_v:1;
+		uint64_t end_swp:2;
+		uint64_t ca:1;
+		uint64_t addr_idx:16;
+		uint64_t reserved_20_63:44;
+#endif
+	} s;
+};
+
+union cvmx_pemx_bar2_mask {
+	uint64_t u64;
+	struct cvmx_pemx_bar2_mask_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_38_63:26;
+		uint64_t mask:35;
+		uint64_t reserved_0_2:3;
+#else
+		uint64_t reserved_0_2:3;
+		uint64_t mask:35;
+		uint64_t reserved_38_63:26;
+#endif
+	} s;
+};
+
+union cvmx_pemx_bar_ctl {
+	uint64_t u64;
+	struct cvmx_pemx_bar_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t bar1_siz:3;
+		uint64_t bar2_enb:1;
+		uint64_t bar2_esx:2;
+		uint64_t bar2_cax:1;
+#else
+		uint64_t bar2_cax:1;
+		uint64_t bar2_esx:2;
+		uint64_t bar2_enb:1;
+		uint64_t bar1_siz:3;
+		uint64_t reserved_7_63:57;
+#endif
+	} s;
+};
+
+union cvmx_pemx_bist_status {
+	uint64_t u64;
+	struct cvmx_pemx_bist_status_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t retry:1;
+		uint64_t rqdata0:1;
+		uint64_t rqdata1:1;
+		uint64_t rqdata2:1;
+		uint64_t rqdata3:1;
+		uint64_t rqhdr1:1;
+		uint64_t rqhdr0:1;
+		uint64_t sot:1;
+#else
+		uint64_t sot:1;
+		uint64_t rqhdr0:1;
+		uint64_t rqhdr1:1;
+		uint64_t rqdata3:1;
+		uint64_t rqdata2:1;
+		uint64_t rqdata1:1;
+		uint64_t rqdata0:1;
+		uint64_t retry:1;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_pemx_bist_status2 {
+	uint64_t u64;
+	struct cvmx_pemx_bist_status2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t e2p_cpl:1;
+		uint64_t e2p_n:1;
+		uint64_t e2p_p:1;
+		uint64_t peai_p2e:1;
+		uint64_t pef_tpf1:1;
+		uint64_t pef_tpf0:1;
+		uint64_t pef_tnf:1;
+		uint64_t pef_tcf1:1;
+		uint64_t pef_tc0:1;
+		uint64_t ppf:1;
+#else
+		uint64_t ppf:1;
+		uint64_t pef_tc0:1;
+		uint64_t pef_tcf1:1;
+		uint64_t pef_tnf:1;
+		uint64_t pef_tpf0:1;
+		uint64_t pef_tpf1:1;
+		uint64_t peai_p2e:1;
+		uint64_t e2p_p:1;
+		uint64_t e2p_n:1;
+		uint64_t e2p_cpl:1;
+		uint64_t reserved_10_63:54;
+#endif
+	} s;
+};
+
+union cvmx_pemx_cfg_rd {
+	uint64_t u64;
+	struct cvmx_pemx_cfg_rd_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t data:32;
+		uint64_t addr:32;
+#else
+		uint64_t addr:32;
+		uint64_t data:32;
+#endif
+	} s;
+};
+
+union cvmx_pemx_cfg_wr {
+	uint64_t u64;
+	struct cvmx_pemx_cfg_wr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t data:32;
+		uint64_t addr:32;
+#else
+		uint64_t addr:32;
+		uint64_t data:32;
+#endif
+	} s;
+};
+
+union cvmx_pemx_cpl_lut_valid {
+	uint64_t u64;
+	struct cvmx_pemx_cpl_lut_valid_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t tag:32;
+#else
+		uint64_t tag:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_pemx_ctl_status {
+	uint64_t u64;
+	struct cvmx_pemx_ctl_status_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t auto_sd:1;
+		uint64_t dnum:5;
+		uint64_t pbus:8;
+		uint64_t reserved_32_33:2;
+		uint64_t cfg_rtry:16;
+		uint64_t reserved_12_15:4;
+		uint64_t pm_xtoff:1;
+		uint64_t pm_xpme:1;
+		uint64_t ob_p_cmd:1;
+		uint64_t reserved_7_8:2;
+		uint64_t nf_ecrc:1;
+		uint64_t dly_one:1;
+		uint64_t lnk_enb:1;
+		uint64_t ro_ctlp:1;
+		uint64_t fast_lm:1;
+		uint64_t inv_ecrc:1;
+		uint64_t inv_lcrc:1;
+#else
+		uint64_t inv_lcrc:1;
+		uint64_t inv_ecrc:1;
+		uint64_t fast_lm:1;
+		uint64_t ro_ctlp:1;
+		uint64_t lnk_enb:1;
+		uint64_t dly_one:1;
+		uint64_t nf_ecrc:1;
+		uint64_t reserved_7_8:2;
+		uint64_t ob_p_cmd:1;
+		uint64_t pm_xpme:1;
+		uint64_t pm_xtoff:1;
+		uint64_t reserved_12_15:4;
+		uint64_t cfg_rtry:16;
+		uint64_t reserved_32_33:2;
+		uint64_t pbus:8;
+		uint64_t dnum:5;
+		uint64_t auto_sd:1;
+		uint64_t reserved_48_63:16;
+#endif
+	} s;
+};
+
+union cvmx_pemx_dbg_info {
+	uint64_t u64;
+	struct cvmx_pemx_dbg_info_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_31_63:33;
+		uint64_t ecrc_e:1;
+		uint64_t rawwpp:1;
+		uint64_t racpp:1;
+		uint64_t ramtlp:1;
+		uint64_t rarwdns:1;
+		uint64_t caar:1;
+		uint64_t racca:1;
+		uint64_t racur:1;
+		uint64_t rauc:1;
+		uint64_t rqo:1;
+		uint64_t fcuv:1;
+		uint64_t rpe:1;
+		uint64_t fcpvwt:1;
+		uint64_t dpeoosd:1;
+		uint64_t rtwdle:1;
+		uint64_t rdwdle:1;
+		uint64_t mre:1;
+		uint64_t rte:1;
+		uint64_t acto:1;
+		uint64_t rvdm:1;
+		uint64_t rumep:1;
+		uint64_t rptamrc:1;
+		uint64_t rpmerc:1;
+		uint64_t rfemrc:1;
+		uint64_t rnfemrc:1;
+		uint64_t rcemrc:1;
+		uint64_t rpoison:1;
+		uint64_t recrce:1;
+		uint64_t rtlplle:1;
+		uint64_t rtlpmal:1;
+		uint64_t spoison:1;
+#else
+		uint64_t spoison:1;
+		uint64_t rtlpmal:1;
+		uint64_t rtlplle:1;
+		uint64_t recrce:1;
+		uint64_t rpoison:1;
+		uint64_t rcemrc:1;
+		uint64_t rnfemrc:1;
+		uint64_t rfemrc:1;
+		uint64_t rpmerc:1;
+		uint64_t rptamrc:1;
+		uint64_t rumep:1;
+		uint64_t rvdm:1;
+		uint64_t acto:1;
+		uint64_t rte:1;
+		uint64_t mre:1;
+		uint64_t rdwdle:1;
+		uint64_t rtwdle:1;
+		uint64_t dpeoosd:1;
+		uint64_t fcpvwt:1;
+		uint64_t rpe:1;
+		uint64_t fcuv:1;
+		uint64_t rqo:1;
+		uint64_t rauc:1;
+		uint64_t racur:1;
+		uint64_t racca:1;
+		uint64_t caar:1;
+		uint64_t rarwdns:1;
+		uint64_t ramtlp:1;
+		uint64_t racpp:1;
+		uint64_t rawwpp:1;
+		uint64_t ecrc_e:1;
+		uint64_t reserved_31_63:33;
+#endif
+	} s;
+};
+
+union cvmx_pemx_dbg_info_en {
+	uint64_t u64;
+	struct cvmx_pemx_dbg_info_en_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_31_63:33;
+		uint64_t ecrc_e:1;
+		uint64_t rawwpp:1;
+		uint64_t racpp:1;
+		uint64_t ramtlp:1;
+		uint64_t rarwdns:1;
+		uint64_t caar:1;
+		uint64_t racca:1;
+		uint64_t racur:1;
+		uint64_t rauc:1;
+		uint64_t rqo:1;
+		uint64_t fcuv:1;
+		uint64_t rpe:1;
+		uint64_t fcpvwt:1;
+		uint64_t dpeoosd:1;
+		uint64_t rtwdle:1;
+		uint64_t rdwdle:1;
+		uint64_t mre:1;
+		uint64_t rte:1;
+		uint64_t acto:1;
+		uint64_t rvdm:1;
+		uint64_t rumep:1;
+		uint64_t rptamrc:1;
+		uint64_t rpmerc:1;
+		uint64_t rfemrc:1;
+		uint64_t rnfemrc:1;
+		uint64_t rcemrc:1;
+		uint64_t rpoison:1;
+		uint64_t recrce:1;
+		uint64_t rtlplle:1;
+		uint64_t rtlpmal:1;
+		uint64_t spoison:1;
+#else
+		uint64_t spoison:1;
+		uint64_t rtlpmal:1;
+		uint64_t rtlplle:1;
+		uint64_t recrce:1;
+		uint64_t rpoison:1;
+		uint64_t rcemrc:1;
+		uint64_t rnfemrc:1;
+		uint64_t rfemrc:1;
+		uint64_t rpmerc:1;
+		uint64_t rptamrc:1;
+		uint64_t rumep:1;
+		uint64_t rvdm:1;
+		uint64_t acto:1;
+		uint64_t rte:1;
+		uint64_t mre:1;
+		uint64_t rdwdle:1;
+		uint64_t rtwdle:1;
+		uint64_t dpeoosd:1;
+		uint64_t fcpvwt:1;
+		uint64_t rpe:1;
+		uint64_t fcuv:1;
+		uint64_t rqo:1;
+		uint64_t rauc:1;
+		uint64_t racur:1;
+		uint64_t racca:1;
+		uint64_t caar:1;
+		uint64_t rarwdns:1;
+		uint64_t ramtlp:1;
+		uint64_t racpp:1;
+		uint64_t rawwpp:1;
+		uint64_t ecrc_e:1;
+		uint64_t reserved_31_63:33;
+#endif
+	} s;
+};
+
+union cvmx_pemx_diag_status {
+	uint64_t u64;
+	struct cvmx_pemx_diag_status_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t pm_dst:1;
+		uint64_t pm_stat:1;
+		uint64_t pm_en:1;
+		uint64_t aux_en:1;
+#else
+		uint64_t aux_en:1;
+		uint64_t pm_en:1;
+		uint64_t pm_stat:1;
+		uint64_t pm_dst:1;
+		uint64_t reserved_4_63:60;
+#endif
+	} s;
+};
+
+union cvmx_pemx_inb_read_credits {
+	uint64_t u64;
+	struct cvmx_pemx_inb_read_credits_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t num:6;
+#else
+		uint64_t num:6;
+		uint64_t reserved_6_63:58;
+#endif
+	} s;
+};
+
+union cvmx_pemx_int_enb {
+	uint64_t u64;
+	struct cvmx_pemx_int_enb_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_14_63:50;
+		uint64_t crs_dr:1;
+		uint64_t crs_er:1;
+		uint64_t rdlk:1;
+		uint64_t exc:1;
+		uint64_t un_bx:1;
+		uint64_t un_b2:1;
+		uint64_t un_b1:1;
+		uint64_t up_bx:1;
+		uint64_t up_b2:1;
+		uint64_t up_b1:1;
+		uint64_t pmem:1;
+		uint64_t pmei:1;
+		uint64_t se:1;
+		uint64_t aeri:1;
+#else
+		uint64_t aeri:1;
+		uint64_t se:1;
+		uint64_t pmei:1;
+		uint64_t pmem:1;
+		uint64_t up_b1:1;
+		uint64_t up_b2:1;
+		uint64_t up_bx:1;
+		uint64_t un_b1:1;
+		uint64_t un_b2:1;
+		uint64_t un_bx:1;
+		uint64_t exc:1;
+		uint64_t rdlk:1;
+		uint64_t crs_er:1;
+		uint64_t crs_dr:1;
+		uint64_t reserved_14_63:50;
+#endif
+	} s;
+};
+
+union cvmx_pemx_int_enb_int {
+	uint64_t u64;
+	struct cvmx_pemx_int_enb_int_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_14_63:50;
+		uint64_t crs_dr:1;
+		uint64_t crs_er:1;
+		uint64_t rdlk:1;
+		uint64_t exc:1;
+		uint64_t un_bx:1;
+		uint64_t un_b2:1;
+		uint64_t un_b1:1;
+		uint64_t up_bx:1;
+		uint64_t up_b2:1;
+		uint64_t up_b1:1;
+		uint64_t pmem:1;
+		uint64_t pmei:1;
+		uint64_t se:1;
+		uint64_t aeri:1;
+#else
+		uint64_t aeri:1;
+		uint64_t se:1;
+		uint64_t pmei:1;
+		uint64_t pmem:1;
+		uint64_t up_b1:1;
+		uint64_t up_b2:1;
+		uint64_t up_bx:1;
+		uint64_t un_b1:1;
+		uint64_t un_b2:1;
+		uint64_t un_bx:1;
+		uint64_t exc:1;
+		uint64_t rdlk:1;
+		uint64_t crs_er:1;
+		uint64_t crs_dr:1;
+		uint64_t reserved_14_63:50;
+#endif
+	} s;
+};
+
+union cvmx_pemx_int_sum {
+	uint64_t u64;
+	struct cvmx_pemx_int_sum_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_14_63:50;
+		uint64_t crs_dr:1;
+		uint64_t crs_er:1;
+		uint64_t rdlk:1;
+		uint64_t exc:1;
+		uint64_t un_bx:1;
+		uint64_t un_b2:1;
+		uint64_t un_b1:1;
+		uint64_t up_bx:1;
+		uint64_t up_b2:1;
+		uint64_t up_b1:1;
+		uint64_t pmem:1;
+		uint64_t pmei:1;
+		uint64_t se:1;
+		uint64_t aeri:1;
+#else
+		uint64_t aeri:1;
+		uint64_t se:1;
+		uint64_t pmei:1;
+		uint64_t pmem:1;
+		uint64_t up_b1:1;
+		uint64_t up_b2:1;
+		uint64_t up_bx:1;
+		uint64_t un_b1:1;
+		uint64_t un_b2:1;
+		uint64_t un_bx:1;
+		uint64_t exc:1;
+		uint64_t rdlk:1;
+		uint64_t crs_er:1;
+		uint64_t crs_dr:1;
+		uint64_t reserved_14_63:50;
+#endif
+	} s;
+};
+
+union cvmx_pemx_p2n_bar0_start {
+	uint64_t u64;
+	struct cvmx_pemx_p2n_bar0_start_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t addr:50;
+		uint64_t reserved_0_13:14;
+#else
+		uint64_t reserved_0_13:14;
+		uint64_t addr:50;
+#endif
+	} s;
+};
+
+union cvmx_pemx_p2n_bar1_start {
+	uint64_t u64;
+	struct cvmx_pemx_p2n_bar1_start_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t addr:38;
+		uint64_t reserved_0_25:26;
+#else
+		uint64_t reserved_0_25:26;
+		uint64_t addr:38;
+#endif
+	} s;
+};
+
+union cvmx_pemx_p2n_bar2_start {
+	uint64_t u64;
+	struct cvmx_pemx_p2n_bar2_start_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t addr:23;
+		uint64_t reserved_0_40:41;
+#else
+		uint64_t reserved_0_40:41;
+		uint64_t addr:23;
+#endif
+	} s;
+};
+
+union cvmx_pemx_p2p_barx_end {
+	uint64_t u64;
+	struct cvmx_pemx_p2p_barx_end_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t addr:52;
+		uint64_t reserved_0_11:12;
+#else
+		uint64_t reserved_0_11:12;
+		uint64_t addr:52;
+#endif
+	} s;
+};
+
+union cvmx_pemx_p2p_barx_start {
+	uint64_t u64;
+	struct cvmx_pemx_p2p_barx_start_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t addr:52;
+		uint64_t reserved_0_11:12;
+#else
+		uint64_t reserved_0_11:12;
+		uint64_t addr:52;
+#endif
+	} s;
+};
+
+union cvmx_pemx_tlp_credits {
+	uint64_t u64;
+	struct cvmx_pemx_tlp_credits_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_56_63:8;
+		uint64_t peai_ppf:8;
+		uint64_t pem_cpl:8;
+		uint64_t pem_np:8;
+		uint64_t pem_p:8;
+		uint64_t sli_cpl:8;
+		uint64_t sli_np:8;
+		uint64_t sli_p:8;
+#else
+		uint64_t sli_p:8;
+		uint64_t sli_np:8;
+		uint64_t sli_cpl:8;
+		uint64_t pem_p:8;
+		uint64_t pem_np:8;
+		uint64_t pem_cpl:8;
+		uint64_t peai_ppf:8;
+		uint64_t reserved_56_63:8;
+#endif
+	} s;
+	struct cvmx_pemx_tlp_credits_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_56_63:8;
+		uint64_t peai_ppf:8;
+		uint64_t reserved_24_47:24;
+		uint64_t sli_cpl:8;
+		uint64_t sli_np:8;
+		uint64_t sli_p:8;
+#else
+		uint64_t sli_p:8;
+		uint64_t sli_np:8;
+		uint64_t sli_cpl:8;
+		uint64_t reserved_24_47:24;
+		uint64_t peai_ppf:8;
+		uint64_t reserved_56_63:8;
+#endif
+	} cn61xx;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-pescx-defs.h b/arch/mips/include/asm/octeon/cvmx-pescx-defs.h
new file mode 100644
index 000000000..665610825
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-pescx-defs.h
@@ -0,0 +1,579 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2012 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_PESCX_DEFS_H__
+#define __CVMX_PESCX_DEFS_H__
+
+#define CVMX_PESCX_BIST_STATUS(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000018ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_PESCX_BIST_STATUS2(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000418ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_PESCX_CFG_RD(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000030ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_PESCX_CFG_WR(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000028ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_PESCX_CPL_LUT_VALID(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000098ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_PESCX_CTL_STATUS(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000000ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_PESCX_CTL_STATUS2(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000400ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_PESCX_DBG_INFO(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000008ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_PESCX_DBG_INFO_EN(block_id) (CVMX_ADD_IO_SEG(0x00011800C80000A0ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_PESCX_DIAG_STATUS(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000020ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_PESCX_P2N_BAR0_START(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000080ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_PESCX_P2N_BAR1_START(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000088ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_PESCX_P2N_BAR2_START(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000090ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_PESCX_P2P_BARX_END(offset, block_id) (CVMX_ADD_IO_SEG(0x00011800C8000048ull) + (((offset) & 3) + ((block_id) & 1) * 0x800000ull) * 16)
+#define CVMX_PESCX_P2P_BARX_START(offset, block_id) (CVMX_ADD_IO_SEG(0x00011800C8000040ull) + (((offset) & 3) + ((block_id) & 1) * 0x800000ull) * 16)
+#define CVMX_PESCX_TLP_CREDITS(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000038ull) + ((block_id) & 1) * 0x8000000ull)
+
+union cvmx_pescx_bist_status {
+	uint64_t u64;
+	struct cvmx_pescx_bist_status_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_13_63:51;
+		uint64_t rqdata5:1;
+		uint64_t ctlp_or:1;
+		uint64_t ntlp_or:1;
+		uint64_t ptlp_or:1;
+		uint64_t retry:1;
+		uint64_t rqdata0:1;
+		uint64_t rqdata1:1;
+		uint64_t rqdata2:1;
+		uint64_t rqdata3:1;
+		uint64_t rqdata4:1;
+		uint64_t rqhdr1:1;
+		uint64_t rqhdr0:1;
+		uint64_t sot:1;
+#else
+		uint64_t sot:1;
+		uint64_t rqhdr0:1;
+		uint64_t rqhdr1:1;
+		uint64_t rqdata4:1;
+		uint64_t rqdata3:1;
+		uint64_t rqdata2:1;
+		uint64_t rqdata1:1;
+		uint64_t rqdata0:1;
+		uint64_t retry:1;
+		uint64_t ptlp_or:1;
+		uint64_t ntlp_or:1;
+		uint64_t ctlp_or:1;
+		uint64_t rqdata5:1;
+		uint64_t reserved_13_63:51;
+#endif
+	} s;
+	struct cvmx_pescx_bist_status_cn52xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t ctlp_or:1;
+		uint64_t ntlp_or:1;
+		uint64_t ptlp_or:1;
+		uint64_t retry:1;
+		uint64_t rqdata0:1;
+		uint64_t rqdata1:1;
+		uint64_t rqdata2:1;
+		uint64_t rqdata3:1;
+		uint64_t rqdata4:1;
+		uint64_t rqhdr1:1;
+		uint64_t rqhdr0:1;
+		uint64_t sot:1;
+#else
+		uint64_t sot:1;
+		uint64_t rqhdr0:1;
+		uint64_t rqhdr1:1;
+		uint64_t rqdata4:1;
+		uint64_t rqdata3:1;
+		uint64_t rqdata2:1;
+		uint64_t rqdata1:1;
+		uint64_t rqdata0:1;
+		uint64_t retry:1;
+		uint64_t ptlp_or:1;
+		uint64_t ntlp_or:1;
+		uint64_t ctlp_or:1;
+		uint64_t reserved_12_63:52;
+#endif
+	} cn52xxp1;
+};
+
+union cvmx_pescx_bist_status2 {
+	uint64_t u64;
+	struct cvmx_pescx_bist_status2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_14_63:50;
+		uint64_t cto_p2e:1;
+		uint64_t e2p_cpl:1;
+		uint64_t e2p_n:1;
+		uint64_t e2p_p:1;
+		uint64_t e2p_rsl:1;
+		uint64_t dbg_p2e:1;
+		uint64_t peai_p2e:1;
+		uint64_t rsl_p2e:1;
+		uint64_t pef_tpf1:1;
+		uint64_t pef_tpf0:1;
+		uint64_t pef_tnf:1;
+		uint64_t pef_tcf1:1;
+		uint64_t pef_tc0:1;
+		uint64_t ppf:1;
+#else
+		uint64_t ppf:1;
+		uint64_t pef_tc0:1;
+		uint64_t pef_tcf1:1;
+		uint64_t pef_tnf:1;
+		uint64_t pef_tpf0:1;
+		uint64_t pef_tpf1:1;
+		uint64_t rsl_p2e:1;
+		uint64_t peai_p2e:1;
+		uint64_t dbg_p2e:1;
+		uint64_t e2p_rsl:1;
+		uint64_t e2p_p:1;
+		uint64_t e2p_n:1;
+		uint64_t e2p_cpl:1;
+		uint64_t cto_p2e:1;
+		uint64_t reserved_14_63:50;
+#endif
+	} s;
+};
+
+union cvmx_pescx_cfg_rd {
+	uint64_t u64;
+	struct cvmx_pescx_cfg_rd_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t data:32;
+		uint64_t addr:32;
+#else
+		uint64_t addr:32;
+		uint64_t data:32;
+#endif
+	} s;
+};
+
+union cvmx_pescx_cfg_wr {
+	uint64_t u64;
+	struct cvmx_pescx_cfg_wr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t data:32;
+		uint64_t addr:32;
+#else
+		uint64_t addr:32;
+		uint64_t data:32;
+#endif
+	} s;
+};
+
+union cvmx_pescx_cpl_lut_valid {
+	uint64_t u64;
+	struct cvmx_pescx_cpl_lut_valid_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t tag:32;
+#else
+		uint64_t tag:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_pescx_ctl_status {
+	uint64_t u64;
+	struct cvmx_pescx_ctl_status_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_28_63:36;
+		uint64_t dnum:5;
+		uint64_t pbus:8;
+		uint64_t qlm_cfg:2;
+		uint64_t lane_swp:1;
+		uint64_t pm_xtoff:1;
+		uint64_t pm_xpme:1;
+		uint64_t ob_p_cmd:1;
+		uint64_t reserved_7_8:2;
+		uint64_t nf_ecrc:1;
+		uint64_t dly_one:1;
+		uint64_t lnk_enb:1;
+		uint64_t ro_ctlp:1;
+		uint64_t reserved_2_2:1;
+		uint64_t inv_ecrc:1;
+		uint64_t inv_lcrc:1;
+#else
+		uint64_t inv_lcrc:1;
+		uint64_t inv_ecrc:1;
+		uint64_t reserved_2_2:1;
+		uint64_t ro_ctlp:1;
+		uint64_t lnk_enb:1;
+		uint64_t dly_one:1;
+		uint64_t nf_ecrc:1;
+		uint64_t reserved_7_8:2;
+		uint64_t ob_p_cmd:1;
+		uint64_t pm_xpme:1;
+		uint64_t pm_xtoff:1;
+		uint64_t lane_swp:1;
+		uint64_t qlm_cfg:2;
+		uint64_t pbus:8;
+		uint64_t dnum:5;
+		uint64_t reserved_28_63:36;
+#endif
+	} s;
+	struct cvmx_pescx_ctl_status_cn56xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_28_63:36;
+		uint64_t dnum:5;
+		uint64_t pbus:8;
+		uint64_t qlm_cfg:2;
+		uint64_t reserved_12_12:1;
+		uint64_t pm_xtoff:1;
+		uint64_t pm_xpme:1;
+		uint64_t ob_p_cmd:1;
+		uint64_t reserved_7_8:2;
+		uint64_t nf_ecrc:1;
+		uint64_t dly_one:1;
+		uint64_t lnk_enb:1;
+		uint64_t ro_ctlp:1;
+		uint64_t reserved_2_2:1;
+		uint64_t inv_ecrc:1;
+		uint64_t inv_lcrc:1;
+#else
+		uint64_t inv_lcrc:1;
+		uint64_t inv_ecrc:1;
+		uint64_t reserved_2_2:1;
+		uint64_t ro_ctlp:1;
+		uint64_t lnk_enb:1;
+		uint64_t dly_one:1;
+		uint64_t nf_ecrc:1;
+		uint64_t reserved_7_8:2;
+		uint64_t ob_p_cmd:1;
+		uint64_t pm_xpme:1;
+		uint64_t pm_xtoff:1;
+		uint64_t reserved_12_12:1;
+		uint64_t qlm_cfg:2;
+		uint64_t pbus:8;
+		uint64_t dnum:5;
+		uint64_t reserved_28_63:36;
+#endif
+	} cn56xx;
+};
+
+union cvmx_pescx_ctl_status2 {
+	uint64_t u64;
+	struct cvmx_pescx_ctl_status2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t pclk_run:1;
+		uint64_t pcierst:1;
+#else
+		uint64_t pcierst:1;
+		uint64_t pclk_run:1;
+		uint64_t reserved_2_63:62;
+#endif
+	} s;
+	struct cvmx_pescx_ctl_status2_cn52xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t pcierst:1;
+#else
+		uint64_t pcierst:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} cn52xxp1;
+};
+
+union cvmx_pescx_dbg_info {
+	uint64_t u64;
+	struct cvmx_pescx_dbg_info_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_31_63:33;
+		uint64_t ecrc_e:1;
+		uint64_t rawwpp:1;
+		uint64_t racpp:1;
+		uint64_t ramtlp:1;
+		uint64_t rarwdns:1;
+		uint64_t caar:1;
+		uint64_t racca:1;
+		uint64_t racur:1;
+		uint64_t rauc:1;
+		uint64_t rqo:1;
+		uint64_t fcuv:1;
+		uint64_t rpe:1;
+		uint64_t fcpvwt:1;
+		uint64_t dpeoosd:1;
+		uint64_t rtwdle:1;
+		uint64_t rdwdle:1;
+		uint64_t mre:1;
+		uint64_t rte:1;
+		uint64_t acto:1;
+		uint64_t rvdm:1;
+		uint64_t rumep:1;
+		uint64_t rptamrc:1;
+		uint64_t rpmerc:1;
+		uint64_t rfemrc:1;
+		uint64_t rnfemrc:1;
+		uint64_t rcemrc:1;
+		uint64_t rpoison:1;
+		uint64_t recrce:1;
+		uint64_t rtlplle:1;
+		uint64_t rtlpmal:1;
+		uint64_t spoison:1;
+#else
+		uint64_t spoison:1;
+		uint64_t rtlpmal:1;
+		uint64_t rtlplle:1;
+		uint64_t recrce:1;
+		uint64_t rpoison:1;
+		uint64_t rcemrc:1;
+		uint64_t rnfemrc:1;
+		uint64_t rfemrc:1;
+		uint64_t rpmerc:1;
+		uint64_t rptamrc:1;
+		uint64_t rumep:1;
+		uint64_t rvdm:1;
+		uint64_t acto:1;
+		uint64_t rte:1;
+		uint64_t mre:1;
+		uint64_t rdwdle:1;
+		uint64_t rtwdle:1;
+		uint64_t dpeoosd:1;
+		uint64_t fcpvwt:1;
+		uint64_t rpe:1;
+		uint64_t fcuv:1;
+		uint64_t rqo:1;
+		uint64_t rauc:1;
+		uint64_t racur:1;
+		uint64_t racca:1;
+		uint64_t caar:1;
+		uint64_t rarwdns:1;
+		uint64_t ramtlp:1;
+		uint64_t racpp:1;
+		uint64_t rawwpp:1;
+		uint64_t ecrc_e:1;
+		uint64_t reserved_31_63:33;
+#endif
+	} s;
+};
+
+union cvmx_pescx_dbg_info_en {
+	uint64_t u64;
+	struct cvmx_pescx_dbg_info_en_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_31_63:33;
+		uint64_t ecrc_e:1;
+		uint64_t rawwpp:1;
+		uint64_t racpp:1;
+		uint64_t ramtlp:1;
+		uint64_t rarwdns:1;
+		uint64_t caar:1;
+		uint64_t racca:1;
+		uint64_t racur:1;
+		uint64_t rauc:1;
+		uint64_t rqo:1;
+		uint64_t fcuv:1;
+		uint64_t rpe:1;
+		uint64_t fcpvwt:1;
+		uint64_t dpeoosd:1;
+		uint64_t rtwdle:1;
+		uint64_t rdwdle:1;
+		uint64_t mre:1;
+		uint64_t rte:1;
+		uint64_t acto:1;
+		uint64_t rvdm:1;
+		uint64_t rumep:1;
+		uint64_t rptamrc:1;
+		uint64_t rpmerc:1;
+		uint64_t rfemrc:1;
+		uint64_t rnfemrc:1;
+		uint64_t rcemrc:1;
+		uint64_t rpoison:1;
+		uint64_t recrce:1;
+		uint64_t rtlplle:1;
+		uint64_t rtlpmal:1;
+		uint64_t spoison:1;
+#else
+		uint64_t spoison:1;
+		uint64_t rtlpmal:1;
+		uint64_t rtlplle:1;
+		uint64_t recrce:1;
+		uint64_t rpoison:1;
+		uint64_t rcemrc:1;
+		uint64_t rnfemrc:1;
+		uint64_t rfemrc:1;
+		uint64_t rpmerc:1;
+		uint64_t rptamrc:1;
+		uint64_t rumep:1;
+		uint64_t rvdm:1;
+		uint64_t acto:1;
+		uint64_t rte:1;
+		uint64_t mre:1;
+		uint64_t rdwdle:1;
+		uint64_t rtwdle:1;
+		uint64_t dpeoosd:1;
+		uint64_t fcpvwt:1;
+		uint64_t rpe:1;
+		uint64_t fcuv:1;
+		uint64_t rqo:1;
+		uint64_t rauc:1;
+		uint64_t racur:1;
+		uint64_t racca:1;
+		uint64_t caar:1;
+		uint64_t rarwdns:1;
+		uint64_t ramtlp:1;
+		uint64_t racpp:1;
+		uint64_t rawwpp:1;
+		uint64_t ecrc_e:1;
+		uint64_t reserved_31_63:33;
+#endif
+	} s;
+};
+
+union cvmx_pescx_diag_status {
+	uint64_t u64;
+	struct cvmx_pescx_diag_status_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t pm_dst:1;
+		uint64_t pm_stat:1;
+		uint64_t pm_en:1;
+		uint64_t aux_en:1;
+#else
+		uint64_t aux_en:1;
+		uint64_t pm_en:1;
+		uint64_t pm_stat:1;
+		uint64_t pm_dst:1;
+		uint64_t reserved_4_63:60;
+#endif
+	} s;
+};
+
+union cvmx_pescx_p2n_bar0_start {
+	uint64_t u64;
+	struct cvmx_pescx_p2n_bar0_start_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t addr:50;
+		uint64_t reserved_0_13:14;
+#else
+		uint64_t reserved_0_13:14;
+		uint64_t addr:50;
+#endif
+	} s;
+};
+
+union cvmx_pescx_p2n_bar1_start {
+	uint64_t u64;
+	struct cvmx_pescx_p2n_bar1_start_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t addr:38;
+		uint64_t reserved_0_25:26;
+#else
+		uint64_t reserved_0_25:26;
+		uint64_t addr:38;
+#endif
+	} s;
+};
+
+union cvmx_pescx_p2n_bar2_start {
+	uint64_t u64;
+	struct cvmx_pescx_p2n_bar2_start_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t addr:25;
+		uint64_t reserved_0_38:39;
+#else
+		uint64_t reserved_0_38:39;
+		uint64_t addr:25;
+#endif
+	} s;
+};
+
+union cvmx_pescx_p2p_barx_end {
+	uint64_t u64;
+	struct cvmx_pescx_p2p_barx_end_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t addr:52;
+		uint64_t reserved_0_11:12;
+#else
+		uint64_t reserved_0_11:12;
+		uint64_t addr:52;
+#endif
+	} s;
+};
+
+union cvmx_pescx_p2p_barx_start {
+	uint64_t u64;
+	struct cvmx_pescx_p2p_barx_start_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t addr:52;
+		uint64_t reserved_0_11:12;
+#else
+		uint64_t reserved_0_11:12;
+		uint64_t addr:52;
+#endif
+	} s;
+};
+
+union cvmx_pescx_tlp_credits {
+	uint64_t u64;
+	struct cvmx_pescx_tlp_credits_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_0_63:64;
+#else
+		uint64_t reserved_0_63:64;
+#endif
+	} s;
+	struct cvmx_pescx_tlp_credits_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_56_63:8;
+		uint64_t peai_ppf:8;
+		uint64_t pesc_cpl:8;
+		uint64_t pesc_np:8;
+		uint64_t pesc_p:8;
+		uint64_t npei_cpl:8;
+		uint64_t npei_np:8;
+		uint64_t npei_p:8;
+#else
+		uint64_t npei_p:8;
+		uint64_t npei_np:8;
+		uint64_t npei_cpl:8;
+		uint64_t pesc_p:8;
+		uint64_t pesc_np:8;
+		uint64_t pesc_cpl:8;
+		uint64_t peai_ppf:8;
+		uint64_t reserved_56_63:8;
+#endif
+	} cn52xx;
+	struct cvmx_pescx_tlp_credits_cn52xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_38_63:26;
+		uint64_t peai_ppf:8;
+		uint64_t pesc_cpl:5;
+		uint64_t pesc_np:5;
+		uint64_t pesc_p:5;
+		uint64_t npei_cpl:5;
+		uint64_t npei_np:5;
+		uint64_t npei_p:5;
+#else
+		uint64_t npei_p:5;
+		uint64_t npei_np:5;
+		uint64_t npei_cpl:5;
+		uint64_t pesc_p:5;
+		uint64_t pesc_np:5;
+		uint64_t pesc_cpl:5;
+		uint64_t peai_ppf:8;
+		uint64_t reserved_38_63:26;
+#endif
+	} cn52xxp1;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-pexp-defs.h b/arch/mips/include/asm/octeon/cvmx-pexp-defs.h
new file mode 100644
index 000000000..eb673f351
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-pexp-defs.h
@@ -0,0 +1,224 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2012 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_PEXP_DEFS_H__
+#define __CVMX_PEXP_DEFS_H__
+
+#define CVMX_PEXP_NPEI_BAR1_INDEXX(offset) (CVMX_ADD_IO_SEG(0x00011F0000008000ull) + ((offset) & 31) * 16)
+#define CVMX_PEXP_NPEI_BIST_STATUS (CVMX_ADD_IO_SEG(0x00011F0000008580ull))
+#define CVMX_PEXP_NPEI_BIST_STATUS2 (CVMX_ADD_IO_SEG(0x00011F0000008680ull))
+#define CVMX_PEXP_NPEI_CTL_PORT0 (CVMX_ADD_IO_SEG(0x00011F0000008250ull))
+#define CVMX_PEXP_NPEI_CTL_PORT1 (CVMX_ADD_IO_SEG(0x00011F0000008260ull))
+#define CVMX_PEXP_NPEI_CTL_STATUS (CVMX_ADD_IO_SEG(0x00011F0000008570ull))
+#define CVMX_PEXP_NPEI_CTL_STATUS2 (CVMX_ADD_IO_SEG(0x00011F000000BC00ull))
+#define CVMX_PEXP_NPEI_DATA_OUT_CNT (CVMX_ADD_IO_SEG(0x00011F00000085F0ull))
+#define CVMX_PEXP_NPEI_DBG_DATA (CVMX_ADD_IO_SEG(0x00011F0000008510ull))
+#define CVMX_PEXP_NPEI_DBG_SELECT (CVMX_ADD_IO_SEG(0x00011F0000008500ull))
+#define CVMX_PEXP_NPEI_DMA0_INT_LEVEL (CVMX_ADD_IO_SEG(0x00011F00000085C0ull))
+#define CVMX_PEXP_NPEI_DMA1_INT_LEVEL (CVMX_ADD_IO_SEG(0x00011F00000085D0ull))
+#define CVMX_PEXP_NPEI_DMAX_COUNTS(offset) (CVMX_ADD_IO_SEG(0x00011F0000008450ull) + ((offset) & 7) * 16)
+#define CVMX_PEXP_NPEI_DMAX_DBELL(offset) (CVMX_ADD_IO_SEG(0x00011F00000083B0ull) + ((offset) & 7) * 16)
+#define CVMX_PEXP_NPEI_DMAX_IBUFF_SADDR(offset) (CVMX_ADD_IO_SEG(0x00011F0000008400ull) + ((offset) & 7) * 16)
+#define CVMX_PEXP_NPEI_DMAX_NADDR(offset) (CVMX_ADD_IO_SEG(0x00011F00000084A0ull) + ((offset) & 7) * 16)
+#define CVMX_PEXP_NPEI_DMA_CNTS (CVMX_ADD_IO_SEG(0x00011F00000085E0ull))
+#define CVMX_PEXP_NPEI_DMA_CONTROL (CVMX_ADD_IO_SEG(0x00011F00000083A0ull))
+#define CVMX_PEXP_NPEI_DMA_PCIE_REQ_NUM (CVMX_ADD_IO_SEG(0x00011F00000085B0ull))
+#define CVMX_PEXP_NPEI_DMA_STATE1 (CVMX_ADD_IO_SEG(0x00011F00000086C0ull))
+#define CVMX_PEXP_NPEI_DMA_STATE1_P1 (CVMX_ADD_IO_SEG(0x00011F0000008680ull))
+#define CVMX_PEXP_NPEI_DMA_STATE2 (CVMX_ADD_IO_SEG(0x00011F00000086D0ull))
+#define CVMX_PEXP_NPEI_DMA_STATE2_P1 (CVMX_ADD_IO_SEG(0x00011F0000008690ull))
+#define CVMX_PEXP_NPEI_DMA_STATE3_P1 (CVMX_ADD_IO_SEG(0x00011F00000086A0ull))
+#define CVMX_PEXP_NPEI_DMA_STATE4_P1 (CVMX_ADD_IO_SEG(0x00011F00000086B0ull))
+#define CVMX_PEXP_NPEI_DMA_STATE5_P1 (CVMX_ADD_IO_SEG(0x00011F00000086C0ull))
+#define CVMX_PEXP_NPEI_INT_A_ENB (CVMX_ADD_IO_SEG(0x00011F0000008560ull))
+#define CVMX_PEXP_NPEI_INT_A_ENB2 (CVMX_ADD_IO_SEG(0x00011F000000BCE0ull))
+#define CVMX_PEXP_NPEI_INT_A_SUM (CVMX_ADD_IO_SEG(0x00011F0000008550ull))
+#define CVMX_PEXP_NPEI_INT_ENB (CVMX_ADD_IO_SEG(0x00011F0000008540ull))
+#define CVMX_PEXP_NPEI_INT_ENB2 (CVMX_ADD_IO_SEG(0x00011F000000BCD0ull))
+#define CVMX_PEXP_NPEI_INT_INFO (CVMX_ADD_IO_SEG(0x00011F0000008590ull))
+#define CVMX_PEXP_NPEI_INT_SUM (CVMX_ADD_IO_SEG(0x00011F0000008530ull))
+#define CVMX_PEXP_NPEI_INT_SUM2 (CVMX_ADD_IO_SEG(0x00011F000000BCC0ull))
+#define CVMX_PEXP_NPEI_LAST_WIN_RDATA0 (CVMX_ADD_IO_SEG(0x00011F0000008600ull))
+#define CVMX_PEXP_NPEI_LAST_WIN_RDATA1 (CVMX_ADD_IO_SEG(0x00011F0000008610ull))
+#define CVMX_PEXP_NPEI_MEM_ACCESS_CTL (CVMX_ADD_IO_SEG(0x00011F00000084F0ull))
+#define CVMX_PEXP_NPEI_MEM_ACCESS_SUBIDX(offset) (CVMX_ADD_IO_SEG(0x00011F0000008280ull) + ((offset) & 31) * 16 - 16*12)
+#define CVMX_PEXP_NPEI_MSI_ENB0 (CVMX_ADD_IO_SEG(0x00011F000000BC50ull))
+#define CVMX_PEXP_NPEI_MSI_ENB1 (CVMX_ADD_IO_SEG(0x00011F000000BC60ull))
+#define CVMX_PEXP_NPEI_MSI_ENB2 (CVMX_ADD_IO_SEG(0x00011F000000BC70ull))
+#define CVMX_PEXP_NPEI_MSI_ENB3 (CVMX_ADD_IO_SEG(0x00011F000000BC80ull))
+#define CVMX_PEXP_NPEI_MSI_RCV0 (CVMX_ADD_IO_SEG(0x00011F000000BC10ull))
+#define CVMX_PEXP_NPEI_MSI_RCV1 (CVMX_ADD_IO_SEG(0x00011F000000BC20ull))
+#define CVMX_PEXP_NPEI_MSI_RCV2 (CVMX_ADD_IO_SEG(0x00011F000000BC30ull))
+#define CVMX_PEXP_NPEI_MSI_RCV3 (CVMX_ADD_IO_SEG(0x00011F000000BC40ull))
+#define CVMX_PEXP_NPEI_MSI_RD_MAP (CVMX_ADD_IO_SEG(0x00011F000000BCA0ull))
+#define CVMX_PEXP_NPEI_MSI_W1C_ENB0 (CVMX_ADD_IO_SEG(0x00011F000000BCF0ull))
+#define CVMX_PEXP_NPEI_MSI_W1C_ENB1 (CVMX_ADD_IO_SEG(0x00011F000000BD00ull))
+#define CVMX_PEXP_NPEI_MSI_W1C_ENB2 (CVMX_ADD_IO_SEG(0x00011F000000BD10ull))
+#define CVMX_PEXP_NPEI_MSI_W1C_ENB3 (CVMX_ADD_IO_SEG(0x00011F000000BD20ull))
+#define CVMX_PEXP_NPEI_MSI_W1S_ENB0 (CVMX_ADD_IO_SEG(0x00011F000000BD30ull))
+#define CVMX_PEXP_NPEI_MSI_W1S_ENB1 (CVMX_ADD_IO_SEG(0x00011F000000BD40ull))
+#define CVMX_PEXP_NPEI_MSI_W1S_ENB2 (CVMX_ADD_IO_SEG(0x00011F000000BD50ull))
+#define CVMX_PEXP_NPEI_MSI_W1S_ENB3 (CVMX_ADD_IO_SEG(0x00011F000000BD60ull))
+#define CVMX_PEXP_NPEI_MSI_WR_MAP (CVMX_ADD_IO_SEG(0x00011F000000BC90ull))
+#define CVMX_PEXP_NPEI_PCIE_CREDIT_CNT (CVMX_ADD_IO_SEG(0x00011F000000BD70ull))
+#define CVMX_PEXP_NPEI_PCIE_MSI_RCV (CVMX_ADD_IO_SEG(0x00011F000000BCB0ull))
+#define CVMX_PEXP_NPEI_PCIE_MSI_RCV_B1 (CVMX_ADD_IO_SEG(0x00011F0000008650ull))
+#define CVMX_PEXP_NPEI_PCIE_MSI_RCV_B2 (CVMX_ADD_IO_SEG(0x00011F0000008660ull))
+#define CVMX_PEXP_NPEI_PCIE_MSI_RCV_B3 (CVMX_ADD_IO_SEG(0x00011F0000008670ull))
+#define CVMX_PEXP_NPEI_PKTX_CNTS(offset) (CVMX_ADD_IO_SEG(0x00011F000000A400ull) + ((offset) & 31) * 16)
+#define CVMX_PEXP_NPEI_PKTX_INSTR_BADDR(offset) (CVMX_ADD_IO_SEG(0x00011F000000A800ull) + ((offset) & 31) * 16)
+#define CVMX_PEXP_NPEI_PKTX_INSTR_BAOFF_DBELL(offset) (CVMX_ADD_IO_SEG(0x00011F000000AC00ull) + ((offset) & 31) * 16)
+#define CVMX_PEXP_NPEI_PKTX_INSTR_FIFO_RSIZE(offset) (CVMX_ADD_IO_SEG(0x00011F000000B000ull) + ((offset) & 31) * 16)
+#define CVMX_PEXP_NPEI_PKTX_INSTR_HEADER(offset) (CVMX_ADD_IO_SEG(0x00011F000000B400ull) + ((offset) & 31) * 16)
+#define CVMX_PEXP_NPEI_PKTX_IN_BP(offset) (CVMX_ADD_IO_SEG(0x00011F000000B800ull) + ((offset) & 31) * 16)
+#define CVMX_PEXP_NPEI_PKTX_SLIST_BADDR(offset) (CVMX_ADD_IO_SEG(0x00011F0000009400ull) + ((offset) & 31) * 16)
+#define CVMX_PEXP_NPEI_PKTX_SLIST_BAOFF_DBELL(offset) (CVMX_ADD_IO_SEG(0x00011F0000009800ull) + ((offset) & 31) * 16)
+#define CVMX_PEXP_NPEI_PKTX_SLIST_FIFO_RSIZE(offset) (CVMX_ADD_IO_SEG(0x00011F0000009C00ull) + ((offset) & 31) * 16)
+#define CVMX_PEXP_NPEI_PKT_CNT_INT (CVMX_ADD_IO_SEG(0x00011F0000009110ull))
+#define CVMX_PEXP_NPEI_PKT_CNT_INT_ENB (CVMX_ADD_IO_SEG(0x00011F0000009130ull))
+#define CVMX_PEXP_NPEI_PKT_DATA_OUT_ES (CVMX_ADD_IO_SEG(0x00011F00000090B0ull))
+#define CVMX_PEXP_NPEI_PKT_DATA_OUT_NS (CVMX_ADD_IO_SEG(0x00011F00000090A0ull))
+#define CVMX_PEXP_NPEI_PKT_DATA_OUT_ROR (CVMX_ADD_IO_SEG(0x00011F0000009090ull))
+#define CVMX_PEXP_NPEI_PKT_DPADDR (CVMX_ADD_IO_SEG(0x00011F0000009080ull))
+#define CVMX_PEXP_NPEI_PKT_INPUT_CONTROL (CVMX_ADD_IO_SEG(0x00011F0000009150ull))
+#define CVMX_PEXP_NPEI_PKT_INSTR_ENB (CVMX_ADD_IO_SEG(0x00011F0000009000ull))
+#define CVMX_PEXP_NPEI_PKT_INSTR_RD_SIZE (CVMX_ADD_IO_SEG(0x00011F0000009190ull))
+#define CVMX_PEXP_NPEI_PKT_INSTR_SIZE (CVMX_ADD_IO_SEG(0x00011F0000009020ull))
+#define CVMX_PEXP_NPEI_PKT_INT_LEVELS (CVMX_ADD_IO_SEG(0x00011F0000009100ull))
+#define CVMX_PEXP_NPEI_PKT_IN_BP (CVMX_ADD_IO_SEG(0x00011F00000086B0ull))
+#define CVMX_PEXP_NPEI_PKT_IN_DONEX_CNTS(offset) (CVMX_ADD_IO_SEG(0x00011F000000A000ull) + ((offset) & 31) * 16)
+#define CVMX_PEXP_NPEI_PKT_IN_INSTR_COUNTS (CVMX_ADD_IO_SEG(0x00011F00000086A0ull))
+#define CVMX_PEXP_NPEI_PKT_IN_PCIE_PORT (CVMX_ADD_IO_SEG(0x00011F00000091A0ull))
+#define CVMX_PEXP_NPEI_PKT_IPTR (CVMX_ADD_IO_SEG(0x00011F0000009070ull))
+#define CVMX_PEXP_NPEI_PKT_OUTPUT_WMARK (CVMX_ADD_IO_SEG(0x00011F0000009160ull))
+#define CVMX_PEXP_NPEI_PKT_OUT_BMODE (CVMX_ADD_IO_SEG(0x00011F00000090D0ull))
+#define CVMX_PEXP_NPEI_PKT_OUT_ENB (CVMX_ADD_IO_SEG(0x00011F0000009010ull))
+#define CVMX_PEXP_NPEI_PKT_PCIE_PORT (CVMX_ADD_IO_SEG(0x00011F00000090E0ull))
+#define CVMX_PEXP_NPEI_PKT_PORT_IN_RST (CVMX_ADD_IO_SEG(0x00011F0000008690ull))
+#define CVMX_PEXP_NPEI_PKT_SLIST_ES (CVMX_ADD_IO_SEG(0x00011F0000009050ull))
+#define CVMX_PEXP_NPEI_PKT_SLIST_ID_SIZE (CVMX_ADD_IO_SEG(0x00011F0000009180ull))
+#define CVMX_PEXP_NPEI_PKT_SLIST_NS (CVMX_ADD_IO_SEG(0x00011F0000009040ull))
+#define CVMX_PEXP_NPEI_PKT_SLIST_ROR (CVMX_ADD_IO_SEG(0x00011F0000009030ull))
+#define CVMX_PEXP_NPEI_PKT_TIME_INT (CVMX_ADD_IO_SEG(0x00011F0000009120ull))
+#define CVMX_PEXP_NPEI_PKT_TIME_INT_ENB (CVMX_ADD_IO_SEG(0x00011F0000009140ull))
+#define CVMX_PEXP_NPEI_RSL_INT_BLOCKS (CVMX_ADD_IO_SEG(0x00011F0000008520ull))
+#define CVMX_PEXP_NPEI_SCRATCH_1 (CVMX_ADD_IO_SEG(0x00011F0000008270ull))
+#define CVMX_PEXP_NPEI_STATE1 (CVMX_ADD_IO_SEG(0x00011F0000008620ull))
+#define CVMX_PEXP_NPEI_STATE2 (CVMX_ADD_IO_SEG(0x00011F0000008630ull))
+#define CVMX_PEXP_NPEI_STATE3 (CVMX_ADD_IO_SEG(0x00011F0000008640ull))
+#define CVMX_PEXP_NPEI_WINDOW_CTL (CVMX_ADD_IO_SEG(0x00011F0000008380ull))
+#define CVMX_PEXP_SLI_BIST_STATUS (CVMX_ADD_IO_SEG(0x00011F0000010580ull))
+#define CVMX_PEXP_SLI_CTL_PORTX(offset) (CVMX_ADD_IO_SEG(0x00011F0000010050ull) + ((offset) & 3) * 16)
+#define CVMX_PEXP_SLI_CTL_STATUS (CVMX_ADD_IO_SEG(0x00011F0000010570ull))
+#define CVMX_PEXP_SLI_DATA_OUT_CNT (CVMX_ADD_IO_SEG(0x00011F00000105F0ull))
+#define CVMX_PEXP_SLI_DBG_DATA (CVMX_ADD_IO_SEG(0x00011F0000010310ull))
+#define CVMX_PEXP_SLI_DBG_SELECT (CVMX_ADD_IO_SEG(0x00011F0000010300ull))
+#define CVMX_PEXP_SLI_DMAX_CNT(offset) (CVMX_ADD_IO_SEG(0x00011F0000010400ull) + ((offset) & 1) * 16)
+#define CVMX_PEXP_SLI_DMAX_INT_LEVEL(offset) (CVMX_ADD_IO_SEG(0x00011F00000103E0ull) + ((offset) & 1) * 16)
+#define CVMX_PEXP_SLI_DMAX_TIM(offset) (CVMX_ADD_IO_SEG(0x00011F0000010420ull) + ((offset) & 1) * 16)
+#define CVMX_PEXP_SLI_INT_ENB_CIU (CVMX_ADD_IO_SEG(0x00011F0000013CD0ull))
+#define CVMX_PEXP_SLI_INT_ENB_PORTX(offset) (CVMX_ADD_IO_SEG(0x00011F0000010340ull) + ((offset) & 1) * 16)
+#define CVMX_PEXP_SLI_INT_SUM (CVMX_ADD_IO_SEG(0x00011F0000010330ull))
+#define CVMX_PEXP_SLI_LAST_WIN_RDATA0 (CVMX_ADD_IO_SEG(0x00011F0000010600ull))
+#define CVMX_PEXP_SLI_LAST_WIN_RDATA1 (CVMX_ADD_IO_SEG(0x00011F0000010610ull))
+#define CVMX_PEXP_SLI_LAST_WIN_RDATA2 (CVMX_ADD_IO_SEG(0x00011F00000106C0ull))
+#define CVMX_PEXP_SLI_LAST_WIN_RDATA3 (CVMX_ADD_IO_SEG(0x00011F00000106D0ull))
+#define CVMX_PEXP_SLI_MAC_CREDIT_CNT (CVMX_ADD_IO_SEG(0x00011F0000013D70ull))
+#define CVMX_PEXP_SLI_MAC_CREDIT_CNT2 (CVMX_ADD_IO_SEG(0x00011F0000013E10ull))
+#define CVMX_PEXP_SLI_MEM_ACCESS_CTL (CVMX_ADD_IO_SEG(0x00011F00000102F0ull))
+#define CVMX_PEXP_SLI_MEM_ACCESS_SUBIDX(offset) (CVMX_ADD_IO_SEG(0x00011F00000100E0ull) + ((offset) & 31) * 16 - 16*12)
+#define CVMX_PEXP_SLI_MSI_ENB0 (CVMX_ADD_IO_SEG(0x00011F0000013C50ull))
+#define CVMX_PEXP_SLI_MSI_ENB1 (CVMX_ADD_IO_SEG(0x00011F0000013C60ull))
+#define CVMX_PEXP_SLI_MSI_ENB2 (CVMX_ADD_IO_SEG(0x00011F0000013C70ull))
+#define CVMX_PEXP_SLI_MSI_ENB3 (CVMX_ADD_IO_SEG(0x00011F0000013C80ull))
+#define CVMX_PEXP_SLI_MSI_RCV0 (CVMX_ADD_IO_SEG(0x00011F0000013C10ull))
+#define CVMX_PEXP_SLI_MSI_RCV1 (CVMX_ADD_IO_SEG(0x00011F0000013C20ull))
+#define CVMX_PEXP_SLI_MSI_RCV2 (CVMX_ADD_IO_SEG(0x00011F0000013C30ull))
+#define CVMX_PEXP_SLI_MSI_RCV3 (CVMX_ADD_IO_SEG(0x00011F0000013C40ull))
+#define CVMX_PEXP_SLI_MSI_RD_MAP (CVMX_ADD_IO_SEG(0x00011F0000013CA0ull))
+#define CVMX_PEXP_SLI_MSI_W1C_ENB0 (CVMX_ADD_IO_SEG(0x00011F0000013CF0ull))
+#define CVMX_PEXP_SLI_MSI_W1C_ENB1 (CVMX_ADD_IO_SEG(0x00011F0000013D00ull))
+#define CVMX_PEXP_SLI_MSI_W1C_ENB2 (CVMX_ADD_IO_SEG(0x00011F0000013D10ull))
+#define CVMX_PEXP_SLI_MSI_W1C_ENB3 (CVMX_ADD_IO_SEG(0x00011F0000013D20ull))
+#define CVMX_PEXP_SLI_MSI_W1S_ENB0 (CVMX_ADD_IO_SEG(0x00011F0000013D30ull))
+#define CVMX_PEXP_SLI_MSI_W1S_ENB1 (CVMX_ADD_IO_SEG(0x00011F0000013D40ull))
+#define CVMX_PEXP_SLI_MSI_W1S_ENB2 (CVMX_ADD_IO_SEG(0x00011F0000013D50ull))
+#define CVMX_PEXP_SLI_MSI_W1S_ENB3 (CVMX_ADD_IO_SEG(0x00011F0000013D60ull))
+#define CVMX_PEXP_SLI_MSI_WR_MAP (CVMX_ADD_IO_SEG(0x00011F0000013C90ull))
+#define CVMX_PEXP_SLI_PCIE_MSI_RCV (CVMX_ADD_IO_SEG(0x00011F0000013CB0ull))
+#define CVMX_PEXP_SLI_PCIE_MSI_RCV_B1 (CVMX_ADD_IO_SEG(0x00011F0000010650ull))
+#define CVMX_PEXP_SLI_PCIE_MSI_RCV_B2 (CVMX_ADD_IO_SEG(0x00011F0000010660ull))
+#define CVMX_PEXP_SLI_PCIE_MSI_RCV_B3 (CVMX_ADD_IO_SEG(0x00011F0000010670ull))
+#define CVMX_PEXP_SLI_PKTX_CNTS(offset) (CVMX_ADD_IO_SEG(0x00011F0000012400ull) + ((offset) & 31) * 16)
+#define CVMX_PEXP_SLI_PKTX_INSTR_BADDR(offset) (CVMX_ADD_IO_SEG(0x00011F0000012800ull) + ((offset) & 31) * 16)
+#define CVMX_PEXP_SLI_PKTX_INSTR_BAOFF_DBELL(offset) (CVMX_ADD_IO_SEG(0x00011F0000012C00ull) + ((offset) & 31) * 16)
+#define CVMX_PEXP_SLI_PKTX_INSTR_FIFO_RSIZE(offset) (CVMX_ADD_IO_SEG(0x00011F0000013000ull) + ((offset) & 31) * 16)
+#define CVMX_PEXP_SLI_PKTX_INSTR_HEADER(offset) (CVMX_ADD_IO_SEG(0x00011F0000013400ull) + ((offset) & 31) * 16)
+#define CVMX_PEXP_SLI_PKTX_IN_BP(offset) (CVMX_ADD_IO_SEG(0x00011F0000013800ull) + ((offset) & 31) * 16)
+#define CVMX_PEXP_SLI_PKTX_OUT_SIZE(offset) (CVMX_ADD_IO_SEG(0x00011F0000010C00ull) + ((offset) & 31) * 16)
+#define CVMX_PEXP_SLI_PKTX_SLIST_BADDR(offset) (CVMX_ADD_IO_SEG(0x00011F0000011400ull) + ((offset) & 31) * 16)
+#define CVMX_PEXP_SLI_PKTX_SLIST_BAOFF_DBELL(offset) (CVMX_ADD_IO_SEG(0x00011F0000011800ull) + ((offset) & 31) * 16)
+#define CVMX_PEXP_SLI_PKTX_SLIST_FIFO_RSIZE(offset) (CVMX_ADD_IO_SEG(0x00011F0000011C00ull) + ((offset) & 31) * 16)
+#define CVMX_PEXP_SLI_PKT_CNT_INT (CVMX_ADD_IO_SEG(0x00011F0000011130ull))
+#define CVMX_PEXP_SLI_PKT_CNT_INT_ENB (CVMX_ADD_IO_SEG(0x00011F0000011150ull))
+#define CVMX_PEXP_SLI_PKT_CTL (CVMX_ADD_IO_SEG(0x00011F0000011220ull))
+#define CVMX_PEXP_SLI_PKT_DATA_OUT_ES (CVMX_ADD_IO_SEG(0x00011F00000110B0ull))
+#define CVMX_PEXP_SLI_PKT_DATA_OUT_NS (CVMX_ADD_IO_SEG(0x00011F00000110A0ull))
+#define CVMX_PEXP_SLI_PKT_DATA_OUT_ROR (CVMX_ADD_IO_SEG(0x00011F0000011090ull))
+#define CVMX_PEXP_SLI_PKT_DPADDR (CVMX_ADD_IO_SEG(0x00011F0000011080ull))
+#define CVMX_PEXP_SLI_PKT_INPUT_CONTROL (CVMX_ADD_IO_SEG(0x00011F0000011170ull))
+#define CVMX_PEXP_SLI_PKT_INSTR_ENB (CVMX_ADD_IO_SEG(0x00011F0000011000ull))
+#define CVMX_PEXP_SLI_PKT_INSTR_RD_SIZE (CVMX_ADD_IO_SEG(0x00011F00000111A0ull))
+#define CVMX_PEXP_SLI_PKT_INSTR_SIZE (CVMX_ADD_IO_SEG(0x00011F0000011020ull))
+#define CVMX_PEXP_SLI_PKT_INT_LEVELS (CVMX_ADD_IO_SEG(0x00011F0000011120ull))
+#define CVMX_PEXP_SLI_PKT_IN_BP (CVMX_ADD_IO_SEG(0x00011F0000011210ull))
+#define CVMX_PEXP_SLI_PKT_IN_DONEX_CNTS(offset) (CVMX_ADD_IO_SEG(0x00011F0000012000ull) + ((offset) & 31) * 16)
+#define CVMX_PEXP_SLI_PKT_IN_INSTR_COUNTS (CVMX_ADD_IO_SEG(0x00011F0000011200ull))
+#define CVMX_PEXP_SLI_PKT_IN_PCIE_PORT (CVMX_ADD_IO_SEG(0x00011F00000111B0ull))
+#define CVMX_PEXP_SLI_PKT_IPTR (CVMX_ADD_IO_SEG(0x00011F0000011070ull))
+#define CVMX_PEXP_SLI_PKT_OUTPUT_WMARK (CVMX_ADD_IO_SEG(0x00011F0000011180ull))
+#define CVMX_PEXP_SLI_PKT_OUT_BMODE (CVMX_ADD_IO_SEG(0x00011F00000110D0ull))
+#define CVMX_PEXP_SLI_PKT_OUT_BP_EN (CVMX_ADD_IO_SEG(0x00011F0000011240ull))
+#define CVMX_PEXP_SLI_PKT_OUT_ENB (CVMX_ADD_IO_SEG(0x00011F0000011010ull))
+#define CVMX_PEXP_SLI_PKT_PCIE_PORT (CVMX_ADD_IO_SEG(0x00011F00000110E0ull))
+#define CVMX_PEXP_SLI_PKT_PORT_IN_RST (CVMX_ADD_IO_SEG(0x00011F00000111F0ull))
+#define CVMX_PEXP_SLI_PKT_SLIST_ES (CVMX_ADD_IO_SEG(0x00011F0000011050ull))
+#define CVMX_PEXP_SLI_PKT_SLIST_NS (CVMX_ADD_IO_SEG(0x00011F0000011040ull))
+#define CVMX_PEXP_SLI_PKT_SLIST_ROR (CVMX_ADD_IO_SEG(0x00011F0000011030ull))
+#define CVMX_PEXP_SLI_PKT_TIME_INT (CVMX_ADD_IO_SEG(0x00011F0000011140ull))
+#define CVMX_PEXP_SLI_PKT_TIME_INT_ENB (CVMX_ADD_IO_SEG(0x00011F0000011160ull))
+#define CVMX_PEXP_SLI_PORTX_PKIND(offset) (CVMX_ADD_IO_SEG(0x00011F0000010800ull) + ((offset) & 31) * 16)
+#define CVMX_PEXP_SLI_S2M_PORTX_CTL(offset) (CVMX_ADD_IO_SEG(0x00011F0000013D80ull) + ((offset) & 3) * 16)
+#define CVMX_PEXP_SLI_SCRATCH_1 (CVMX_ADD_IO_SEG(0x00011F00000103C0ull))
+#define CVMX_PEXP_SLI_SCRATCH_2 (CVMX_ADD_IO_SEG(0x00011F00000103D0ull))
+#define CVMX_PEXP_SLI_STATE1 (CVMX_ADD_IO_SEG(0x00011F0000010620ull))
+#define CVMX_PEXP_SLI_STATE2 (CVMX_ADD_IO_SEG(0x00011F0000010630ull))
+#define CVMX_PEXP_SLI_STATE3 (CVMX_ADD_IO_SEG(0x00011F0000010640ull))
+#define CVMX_PEXP_SLI_TX_PIPE (CVMX_ADD_IO_SEG(0x00011F0000011230ull))
+#define CVMX_PEXP_SLI_WINDOW_CTL (CVMX_ADD_IO_SEG(0x00011F00000102E0ull))
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-pip-defs.h b/arch/mips/include/asm/octeon/cvmx-pip-defs.h
new file mode 100644
index 000000000..e42f411bd
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-pip-defs.h
@@ -0,0 +1,2734 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2012 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_PIP_DEFS_H__
+#define __CVMX_PIP_DEFS_H__
+
+/*
+ * Enumeration representing the amount of packet processing
+ * and validation performed by the input hardware.
+ */
+enum cvmx_pip_port_parse_mode {
+	/*
+	 * Packet input doesn't perform any processing of the input
+	 * packet.
+	 */
+	CVMX_PIP_PORT_CFG_MODE_NONE = 0ull,
+	/*
+	 * Full packet processing is performed with pointer starting
+	 * at the L2 (ethernet MAC) header.
+	 */
+	CVMX_PIP_PORT_CFG_MODE_SKIPL2 = 1ull,
+	/*
+	 * Input packets are assumed to be IP.	Results from non IP
+	 * packets is undefined. Pointers reference the beginning of
+	 * the IP header.
+	 */
+	CVMX_PIP_PORT_CFG_MODE_SKIPIP = 2ull
+};
+
+#define CVMX_PIP_ALT_SKIP_CFGX(offset) (CVMX_ADD_IO_SEG(0x00011800A0002A00ull) + ((offset) & 3) * 8)
+#define CVMX_PIP_BCK_PRS (CVMX_ADD_IO_SEG(0x00011800A0000038ull))
+#define CVMX_PIP_BIST_STATUS (CVMX_ADD_IO_SEG(0x00011800A0000000ull))
+#define CVMX_PIP_BSEL_EXT_CFGX(offset) (CVMX_ADD_IO_SEG(0x00011800A0002800ull) + ((offset) & 3) * 16)
+#define CVMX_PIP_BSEL_EXT_POSX(offset) (CVMX_ADD_IO_SEG(0x00011800A0002808ull) + ((offset) & 3) * 16)
+#define CVMX_PIP_BSEL_TBL_ENTX(offset) (CVMX_ADD_IO_SEG(0x00011800A0003000ull) + ((offset) & 511) * 8)
+#define CVMX_PIP_CLKEN (CVMX_ADD_IO_SEG(0x00011800A0000040ull))
+#define CVMX_PIP_CRC_CTLX(offset) (CVMX_ADD_IO_SEG(0x00011800A0000040ull) + ((offset) & 1) * 8)
+#define CVMX_PIP_CRC_IVX(offset) (CVMX_ADD_IO_SEG(0x00011800A0000050ull) + ((offset) & 1) * 8)
+#define CVMX_PIP_DEC_IPSECX(offset) (CVMX_ADD_IO_SEG(0x00011800A0000080ull) + ((offset) & 3) * 8)
+#define CVMX_PIP_DSA_SRC_GRP (CVMX_ADD_IO_SEG(0x00011800A0000190ull))
+#define CVMX_PIP_DSA_VID_GRP (CVMX_ADD_IO_SEG(0x00011800A0000198ull))
+#define CVMX_PIP_FRM_LEN_CHKX(offset) (CVMX_ADD_IO_SEG(0x00011800A0000180ull) + ((offset) & 1) * 8)
+#define CVMX_PIP_GBL_CFG (CVMX_ADD_IO_SEG(0x00011800A0000028ull))
+#define CVMX_PIP_GBL_CTL (CVMX_ADD_IO_SEG(0x00011800A0000020ull))
+#define CVMX_PIP_HG_PRI_QOS (CVMX_ADD_IO_SEG(0x00011800A00001A0ull))
+#define CVMX_PIP_INT_EN (CVMX_ADD_IO_SEG(0x00011800A0000010ull))
+#define CVMX_PIP_INT_REG (CVMX_ADD_IO_SEG(0x00011800A0000008ull))
+#define CVMX_PIP_IP_OFFSET (CVMX_ADD_IO_SEG(0x00011800A0000060ull))
+#define CVMX_PIP_PRI_TBLX(offset) (CVMX_ADD_IO_SEG(0x00011800A0004000ull) + ((offset) & 255) * 8)
+#define CVMX_PIP_PRT_CFGBX(offset) (CVMX_ADD_IO_SEG(0x00011800A0008000ull) + ((offset) & 63) * 8)
+#define CVMX_PIP_PRT_CFGX(offset) (CVMX_ADD_IO_SEG(0x00011800A0000200ull) + ((offset) & 63) * 8)
+#define CVMX_PIP_PRT_TAGX(offset) (CVMX_ADD_IO_SEG(0x00011800A0000400ull) + ((offset) & 63) * 8)
+#define CVMX_PIP_QOS_DIFFX(offset) (CVMX_ADD_IO_SEG(0x00011800A0000600ull) + ((offset) & 63) * 8)
+#define CVMX_PIP_QOS_VLANX(offset) (CVMX_ADD_IO_SEG(0x00011800A00000C0ull) + ((offset) & 7) * 8)
+#define CVMX_PIP_QOS_WATCHX(offset) (CVMX_ADD_IO_SEG(0x00011800A0000100ull) + ((offset) & 7) * 8)
+#define CVMX_PIP_RAW_WORD (CVMX_ADD_IO_SEG(0x00011800A00000B0ull))
+#define CVMX_PIP_SFT_RST (CVMX_ADD_IO_SEG(0x00011800A0000030ull))
+#define CVMX_PIP_STAT0_PRTX(offset) (CVMX_ADD_IO_SEG(0x00011800A0000800ull) + ((offset) & 63) * 80)
+#define CVMX_PIP_STAT0_X(offset) (CVMX_ADD_IO_SEG(0x00011800A0040000ull) + ((offset) & 63) * 128)
+#define CVMX_PIP_STAT10_PRTX(offset) (CVMX_ADD_IO_SEG(0x00011800A0001480ull) + ((offset) & 63) * 16)
+#define CVMX_PIP_STAT10_X(offset) (CVMX_ADD_IO_SEG(0x00011800A0040050ull) + ((offset) & 63) * 128)
+#define CVMX_PIP_STAT11_PRTX(offset) (CVMX_ADD_IO_SEG(0x00011800A0001488ull) + ((offset) & 63) * 16)
+#define CVMX_PIP_STAT11_X(offset) (CVMX_ADD_IO_SEG(0x00011800A0040058ull) + ((offset) & 63) * 128)
+#define CVMX_PIP_STAT1_PRTX(offset) (CVMX_ADD_IO_SEG(0x00011800A0000808ull) + ((offset) & 63) * 80)
+#define CVMX_PIP_STAT1_X(offset) (CVMX_ADD_IO_SEG(0x00011800A0040008ull) + ((offset) & 63) * 128)
+#define CVMX_PIP_STAT2_PRTX(offset) (CVMX_ADD_IO_SEG(0x00011800A0000810ull) + ((offset) & 63) * 80)
+#define CVMX_PIP_STAT2_X(offset) (CVMX_ADD_IO_SEG(0x00011800A0040010ull) + ((offset) & 63) * 128)
+#define CVMX_PIP_STAT3_PRTX(offset) (CVMX_ADD_IO_SEG(0x00011800A0000818ull) + ((offset) & 63) * 80)
+#define CVMX_PIP_STAT3_X(offset) (CVMX_ADD_IO_SEG(0x00011800A0040018ull) + ((offset) & 63) * 128)
+#define CVMX_PIP_STAT4_PRTX(offset) (CVMX_ADD_IO_SEG(0x00011800A0000820ull) + ((offset) & 63) * 80)
+#define CVMX_PIP_STAT4_X(offset) (CVMX_ADD_IO_SEG(0x00011800A0040020ull) + ((offset) & 63) * 128)
+#define CVMX_PIP_STAT5_PRTX(offset) (CVMX_ADD_IO_SEG(0x00011800A0000828ull) + ((offset) & 63) * 80)
+#define CVMX_PIP_STAT5_X(offset) (CVMX_ADD_IO_SEG(0x00011800A0040028ull) + ((offset) & 63) * 128)
+#define CVMX_PIP_STAT6_PRTX(offset) (CVMX_ADD_IO_SEG(0x00011800A0000830ull) + ((offset) & 63) * 80)
+#define CVMX_PIP_STAT6_X(offset) (CVMX_ADD_IO_SEG(0x00011800A0040030ull) + ((offset) & 63) * 128)
+#define CVMX_PIP_STAT7_PRTX(offset) (CVMX_ADD_IO_SEG(0x00011800A0000838ull) + ((offset) & 63) * 80)
+#define CVMX_PIP_STAT7_X(offset) (CVMX_ADD_IO_SEG(0x00011800A0040038ull) + ((offset) & 63) * 128)
+#define CVMX_PIP_STAT8_PRTX(offset) (CVMX_ADD_IO_SEG(0x00011800A0000840ull) + ((offset) & 63) * 80)
+#define CVMX_PIP_STAT8_X(offset) (CVMX_ADD_IO_SEG(0x00011800A0040040ull) + ((offset) & 63) * 128)
+#define CVMX_PIP_STAT9_PRTX(offset) (CVMX_ADD_IO_SEG(0x00011800A0000848ull) + ((offset) & 63) * 80)
+#define CVMX_PIP_STAT9_X(offset) (CVMX_ADD_IO_SEG(0x00011800A0040048ull) + ((offset) & 63) * 128)
+#define CVMX_PIP_STAT_CTL (CVMX_ADD_IO_SEG(0x00011800A0000018ull))
+#define CVMX_PIP_STAT_INB_ERRSX(offset) (CVMX_ADD_IO_SEG(0x00011800A0001A10ull) + ((offset) & 63) * 32)
+#define CVMX_PIP_STAT_INB_ERRS_PKNDX(offset) (CVMX_ADD_IO_SEG(0x00011800A0020010ull) + ((offset) & 63) * 32)
+#define CVMX_PIP_STAT_INB_OCTSX(offset) (CVMX_ADD_IO_SEG(0x00011800A0001A08ull) + ((offset) & 63) * 32)
+#define CVMX_PIP_STAT_INB_OCTS_PKNDX(offset) (CVMX_ADD_IO_SEG(0x00011800A0020008ull) + ((offset) & 63) * 32)
+#define CVMX_PIP_STAT_INB_PKTSX(offset) (CVMX_ADD_IO_SEG(0x00011800A0001A00ull) + ((offset) & 63) * 32)
+#define CVMX_PIP_STAT_INB_PKTS_PKNDX(offset) (CVMX_ADD_IO_SEG(0x00011800A0020000ull) + ((offset) & 63) * 32)
+#define CVMX_PIP_SUB_PKIND_FCSX(block_id) (CVMX_ADD_IO_SEG(0x00011800A0080000ull))
+#define CVMX_PIP_TAG_INCX(offset) (CVMX_ADD_IO_SEG(0x00011800A0001800ull) + ((offset) & 63) * 8)
+#define CVMX_PIP_TAG_MASK (CVMX_ADD_IO_SEG(0x00011800A0000070ull))
+#define CVMX_PIP_TAG_SECRET (CVMX_ADD_IO_SEG(0x00011800A0000068ull))
+#define CVMX_PIP_TODO_ENTRY (CVMX_ADD_IO_SEG(0x00011800A0000078ull))
+#define CVMX_PIP_VLAN_ETYPESX(offset) (CVMX_ADD_IO_SEG(0x00011800A00001C0ull) + ((offset) & 1) * 8)
+#define CVMX_PIP_XSTAT0_PRTX(offset) (CVMX_ADD_IO_SEG(0x00011800A0002000ull) + ((offset) & 63) * 80 - 80*40)
+#define CVMX_PIP_XSTAT10_PRTX(offset) (CVMX_ADD_IO_SEG(0x00011800A0001700ull) + ((offset) & 63) * 16 - 16*40)
+#define CVMX_PIP_XSTAT11_PRTX(offset) (CVMX_ADD_IO_SEG(0x00011800A0001708ull) + ((offset) & 63) * 16 - 16*40)
+#define CVMX_PIP_XSTAT1_PRTX(offset) (CVMX_ADD_IO_SEG(0x00011800A0002008ull) + ((offset) & 63) * 80 - 80*40)
+#define CVMX_PIP_XSTAT2_PRTX(offset) (CVMX_ADD_IO_SEG(0x00011800A0002010ull) + ((offset) & 63) * 80 - 80*40)
+#define CVMX_PIP_XSTAT3_PRTX(offset) (CVMX_ADD_IO_SEG(0x00011800A0002018ull) + ((offset) & 63) * 80 - 80*40)
+#define CVMX_PIP_XSTAT4_PRTX(offset) (CVMX_ADD_IO_SEG(0x00011800A0002020ull) + ((offset) & 63) * 80 - 80*40)
+#define CVMX_PIP_XSTAT5_PRTX(offset) (CVMX_ADD_IO_SEG(0x00011800A0002028ull) + ((offset) & 63) * 80 - 80*40)
+#define CVMX_PIP_XSTAT6_PRTX(offset) (CVMX_ADD_IO_SEG(0x00011800A0002030ull) + ((offset) & 63) * 80 - 80*40)
+#define CVMX_PIP_XSTAT7_PRTX(offset) (CVMX_ADD_IO_SEG(0x00011800A0002038ull) + ((offset) & 63) * 80 - 80*40)
+#define CVMX_PIP_XSTAT8_PRTX(offset) (CVMX_ADD_IO_SEG(0x00011800A0002040ull) + ((offset) & 63) * 80 - 80*40)
+#define CVMX_PIP_XSTAT9_PRTX(offset) (CVMX_ADD_IO_SEG(0x00011800A0002048ull) + ((offset) & 63) * 80 - 80*40)
+
+union cvmx_pip_alt_skip_cfgx {
+	uint64_t u64;
+	struct cvmx_pip_alt_skip_cfgx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_57_63:7;
+		uint64_t len:1;
+		uint64_t reserved_46_55:10;
+		uint64_t bit1:6;
+		uint64_t reserved_38_39:2;
+		uint64_t bit0:6;
+		uint64_t reserved_23_31:9;
+		uint64_t skip3:7;
+		uint64_t reserved_15_15:1;
+		uint64_t skip2:7;
+		uint64_t reserved_7_7:1;
+		uint64_t skip1:7;
+#else
+		uint64_t skip1:7;
+		uint64_t reserved_7_7:1;
+		uint64_t skip2:7;
+		uint64_t reserved_15_15:1;
+		uint64_t skip3:7;
+		uint64_t reserved_23_31:9;
+		uint64_t bit0:6;
+		uint64_t reserved_38_39:2;
+		uint64_t bit1:6;
+		uint64_t reserved_46_55:10;
+		uint64_t len:1;
+		uint64_t reserved_57_63:7;
+#endif
+	} s;
+};
+
+union cvmx_pip_bck_prs {
+	uint64_t u64;
+	struct cvmx_pip_bck_prs_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t bckprs:1;
+		uint64_t reserved_13_62:50;
+		uint64_t hiwater:5;
+		uint64_t reserved_5_7:3;
+		uint64_t lowater:5;
+#else
+		uint64_t lowater:5;
+		uint64_t reserved_5_7:3;
+		uint64_t hiwater:5;
+		uint64_t reserved_13_62:50;
+		uint64_t bckprs:1;
+#endif
+	} s;
+};
+
+union cvmx_pip_bist_status {
+	uint64_t u64;
+	struct cvmx_pip_bist_status_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_22_63:42;
+		uint64_t bist:22;
+#else
+		uint64_t bist:22;
+		uint64_t reserved_22_63:42;
+#endif
+	} s;
+	struct cvmx_pip_bist_status_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_18_63:46;
+		uint64_t bist:18;
+#else
+		uint64_t bist:18;
+		uint64_t reserved_18_63:46;
+#endif
+	} cn30xx;
+	struct cvmx_pip_bist_status_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_17_63:47;
+		uint64_t bist:17;
+#else
+		uint64_t bist:17;
+		uint64_t reserved_17_63:47;
+#endif
+	} cn50xx;
+	struct cvmx_pip_bist_status_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t bist:20;
+#else
+		uint64_t bist:20;
+		uint64_t reserved_20_63:44;
+#endif
+	} cn61xx;
+};
+
+union cvmx_pip_bsel_ext_cfgx {
+	uint64_t u64;
+	struct cvmx_pip_bsel_ext_cfgx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_56_63:8;
+		uint64_t upper_tag:16;
+		uint64_t tag:8;
+		uint64_t reserved_25_31:7;
+		uint64_t offset:9;
+		uint64_t reserved_7_15:9;
+		uint64_t skip:7;
+#else
+		uint64_t skip:7;
+		uint64_t reserved_7_15:9;
+		uint64_t offset:9;
+		uint64_t reserved_25_31:7;
+		uint64_t tag:8;
+		uint64_t upper_tag:16;
+		uint64_t reserved_56_63:8;
+#endif
+	} s;
+};
+
+union cvmx_pip_bsel_ext_posx {
+	uint64_t u64;
+	struct cvmx_pip_bsel_ext_posx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t pos7_val:1;
+		uint64_t pos7:7;
+		uint64_t pos6_val:1;
+		uint64_t pos6:7;
+		uint64_t pos5_val:1;
+		uint64_t pos5:7;
+		uint64_t pos4_val:1;
+		uint64_t pos4:7;
+		uint64_t pos3_val:1;
+		uint64_t pos3:7;
+		uint64_t pos2_val:1;
+		uint64_t pos2:7;
+		uint64_t pos1_val:1;
+		uint64_t pos1:7;
+		uint64_t pos0_val:1;
+		uint64_t pos0:7;
+#else
+		uint64_t pos0:7;
+		uint64_t pos0_val:1;
+		uint64_t pos1:7;
+		uint64_t pos1_val:1;
+		uint64_t pos2:7;
+		uint64_t pos2_val:1;
+		uint64_t pos3:7;
+		uint64_t pos3_val:1;
+		uint64_t pos4:7;
+		uint64_t pos4_val:1;
+		uint64_t pos5:7;
+		uint64_t pos5_val:1;
+		uint64_t pos6:7;
+		uint64_t pos6_val:1;
+		uint64_t pos7:7;
+		uint64_t pos7_val:1;
+#endif
+	} s;
+};
+
+union cvmx_pip_bsel_tbl_entx {
+	uint64_t u64;
+	struct cvmx_pip_bsel_tbl_entx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t tag_en:1;
+		uint64_t grp_en:1;
+		uint64_t tt_en:1;
+		uint64_t qos_en:1;
+		uint64_t reserved_40_59:20;
+		uint64_t tag:8;
+		uint64_t reserved_22_31:10;
+		uint64_t grp:6;
+		uint64_t reserved_10_15:6;
+		uint64_t tt:2;
+		uint64_t reserved_3_7:5;
+		uint64_t qos:3;
+#else
+		uint64_t qos:3;
+		uint64_t reserved_3_7:5;
+		uint64_t tt:2;
+		uint64_t reserved_10_15:6;
+		uint64_t grp:6;
+		uint64_t reserved_22_31:10;
+		uint64_t tag:8;
+		uint64_t reserved_40_59:20;
+		uint64_t qos_en:1;
+		uint64_t tt_en:1;
+		uint64_t grp_en:1;
+		uint64_t tag_en:1;
+#endif
+	} s;
+	struct cvmx_pip_bsel_tbl_entx_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t tag_en:1;
+		uint64_t grp_en:1;
+		uint64_t tt_en:1;
+		uint64_t qos_en:1;
+		uint64_t reserved_40_59:20;
+		uint64_t tag:8;
+		uint64_t reserved_20_31:12;
+		uint64_t grp:4;
+		uint64_t reserved_10_15:6;
+		uint64_t tt:2;
+		uint64_t reserved_3_7:5;
+		uint64_t qos:3;
+#else
+		uint64_t qos:3;
+		uint64_t reserved_3_7:5;
+		uint64_t tt:2;
+		uint64_t reserved_10_15:6;
+		uint64_t grp:4;
+		uint64_t reserved_20_31:12;
+		uint64_t tag:8;
+		uint64_t reserved_40_59:20;
+		uint64_t qos_en:1;
+		uint64_t tt_en:1;
+		uint64_t grp_en:1;
+		uint64_t tag_en:1;
+#endif
+	} cn61xx;
+};
+
+union cvmx_pip_clken {
+	uint64_t u64;
+	struct cvmx_pip_clken_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t clken:1;
+#else
+		uint64_t clken:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_pip_crc_ctlx {
+	uint64_t u64;
+	struct cvmx_pip_crc_ctlx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t invres:1;
+		uint64_t reflect:1;
+#else
+		uint64_t reflect:1;
+		uint64_t invres:1;
+		uint64_t reserved_2_63:62;
+#endif
+	} s;
+};
+
+union cvmx_pip_crc_ivx {
+	uint64_t u64;
+	struct cvmx_pip_crc_ivx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t iv:32;
+#else
+		uint64_t iv:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_dec_ipsecx {
+	uint64_t u64;
+	struct cvmx_pip_dec_ipsecx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_18_63:46;
+		uint64_t tcp:1;
+		uint64_t udp:1;
+		uint64_t dprt:16;
+#else
+		uint64_t dprt:16;
+		uint64_t udp:1;
+		uint64_t tcp:1;
+		uint64_t reserved_18_63:46;
+#endif
+	} s;
+};
+
+union cvmx_pip_dsa_src_grp {
+	uint64_t u64;
+	struct cvmx_pip_dsa_src_grp_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t map15:4;
+		uint64_t map14:4;
+		uint64_t map13:4;
+		uint64_t map12:4;
+		uint64_t map11:4;
+		uint64_t map10:4;
+		uint64_t map9:4;
+		uint64_t map8:4;
+		uint64_t map7:4;
+		uint64_t map6:4;
+		uint64_t map5:4;
+		uint64_t map4:4;
+		uint64_t map3:4;
+		uint64_t map2:4;
+		uint64_t map1:4;
+		uint64_t map0:4;
+#else
+		uint64_t map0:4;
+		uint64_t map1:4;
+		uint64_t map2:4;
+		uint64_t map3:4;
+		uint64_t map4:4;
+		uint64_t map5:4;
+		uint64_t map6:4;
+		uint64_t map7:4;
+		uint64_t map8:4;
+		uint64_t map9:4;
+		uint64_t map10:4;
+		uint64_t map11:4;
+		uint64_t map12:4;
+		uint64_t map13:4;
+		uint64_t map14:4;
+		uint64_t map15:4;
+#endif
+	} s;
+};
+
+union cvmx_pip_dsa_vid_grp {
+	uint64_t u64;
+	struct cvmx_pip_dsa_vid_grp_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t map15:4;
+		uint64_t map14:4;
+		uint64_t map13:4;
+		uint64_t map12:4;
+		uint64_t map11:4;
+		uint64_t map10:4;
+		uint64_t map9:4;
+		uint64_t map8:4;
+		uint64_t map7:4;
+		uint64_t map6:4;
+		uint64_t map5:4;
+		uint64_t map4:4;
+		uint64_t map3:4;
+		uint64_t map2:4;
+		uint64_t map1:4;
+		uint64_t map0:4;
+#else
+		uint64_t map0:4;
+		uint64_t map1:4;
+		uint64_t map2:4;
+		uint64_t map3:4;
+		uint64_t map4:4;
+		uint64_t map5:4;
+		uint64_t map6:4;
+		uint64_t map7:4;
+		uint64_t map8:4;
+		uint64_t map9:4;
+		uint64_t map10:4;
+		uint64_t map11:4;
+		uint64_t map12:4;
+		uint64_t map13:4;
+		uint64_t map14:4;
+		uint64_t map15:4;
+#endif
+	} s;
+};
+
+union cvmx_pip_frm_len_chkx {
+	uint64_t u64;
+	struct cvmx_pip_frm_len_chkx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t maxlen:16;
+		uint64_t minlen:16;
+#else
+		uint64_t minlen:16;
+		uint64_t maxlen:16;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_gbl_cfg {
+	uint64_t u64;
+	struct cvmx_pip_gbl_cfg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_19_63:45;
+		uint64_t tag_syn:1;
+		uint64_t ip6_udp:1;
+		uint64_t max_l2:1;
+		uint64_t reserved_11_15:5;
+		uint64_t raw_shf:3;
+		uint64_t reserved_3_7:5;
+		uint64_t nip_shf:3;
+#else
+		uint64_t nip_shf:3;
+		uint64_t reserved_3_7:5;
+		uint64_t raw_shf:3;
+		uint64_t reserved_11_15:5;
+		uint64_t max_l2:1;
+		uint64_t ip6_udp:1;
+		uint64_t tag_syn:1;
+		uint64_t reserved_19_63:45;
+#endif
+	} s;
+};
+
+union cvmx_pip_gbl_ctl {
+	uint64_t u64;
+	struct cvmx_pip_gbl_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t egrp_dis:1;
+		uint64_t ihmsk_dis:1;
+		uint64_t dsa_grp_tvid:1;
+		uint64_t dsa_grp_scmd:1;
+		uint64_t dsa_grp_sid:1;
+		uint64_t reserved_21_23:3;
+		uint64_t ring_en:1;
+		uint64_t reserved_17_19:3;
+		uint64_t ignrs:1;
+		uint64_t vs_wqe:1;
+		uint64_t vs_qos:1;
+		uint64_t l2_mal:1;
+		uint64_t tcp_flag:1;
+		uint64_t l4_len:1;
+		uint64_t l4_chk:1;
+		uint64_t l4_prt:1;
+		uint64_t l4_mal:1;
+		uint64_t reserved_6_7:2;
+		uint64_t ip6_eext:2;
+		uint64_t ip4_opts:1;
+		uint64_t ip_hop:1;
+		uint64_t ip_mal:1;
+		uint64_t ip_chk:1;
+#else
+		uint64_t ip_chk:1;
+		uint64_t ip_mal:1;
+		uint64_t ip_hop:1;
+		uint64_t ip4_opts:1;
+		uint64_t ip6_eext:2;
+		uint64_t reserved_6_7:2;
+		uint64_t l4_mal:1;
+		uint64_t l4_prt:1;
+		uint64_t l4_chk:1;
+		uint64_t l4_len:1;
+		uint64_t tcp_flag:1;
+		uint64_t l2_mal:1;
+		uint64_t vs_qos:1;
+		uint64_t vs_wqe:1;
+		uint64_t ignrs:1;
+		uint64_t reserved_17_19:3;
+		uint64_t ring_en:1;
+		uint64_t reserved_21_23:3;
+		uint64_t dsa_grp_sid:1;
+		uint64_t dsa_grp_scmd:1;
+		uint64_t dsa_grp_tvid:1;
+		uint64_t ihmsk_dis:1;
+		uint64_t egrp_dis:1;
+		uint64_t reserved_29_63:35;
+#endif
+	} s;
+	struct cvmx_pip_gbl_ctl_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_17_63:47;
+		uint64_t ignrs:1;
+		uint64_t vs_wqe:1;
+		uint64_t vs_qos:1;
+		uint64_t l2_mal:1;
+		uint64_t tcp_flag:1;
+		uint64_t l4_len:1;
+		uint64_t l4_chk:1;
+		uint64_t l4_prt:1;
+		uint64_t l4_mal:1;
+		uint64_t reserved_6_7:2;
+		uint64_t ip6_eext:2;
+		uint64_t ip4_opts:1;
+		uint64_t ip_hop:1;
+		uint64_t ip_mal:1;
+		uint64_t ip_chk:1;
+#else
+		uint64_t ip_chk:1;
+		uint64_t ip_mal:1;
+		uint64_t ip_hop:1;
+		uint64_t ip4_opts:1;
+		uint64_t ip6_eext:2;
+		uint64_t reserved_6_7:2;
+		uint64_t l4_mal:1;
+		uint64_t l4_prt:1;
+		uint64_t l4_chk:1;
+		uint64_t l4_len:1;
+		uint64_t tcp_flag:1;
+		uint64_t l2_mal:1;
+		uint64_t vs_qos:1;
+		uint64_t vs_wqe:1;
+		uint64_t ignrs:1;
+		uint64_t reserved_17_63:47;
+#endif
+	} cn30xx;
+	struct cvmx_pip_gbl_ctl_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_27_63:37;
+		uint64_t dsa_grp_tvid:1;
+		uint64_t dsa_grp_scmd:1;
+		uint64_t dsa_grp_sid:1;
+		uint64_t reserved_21_23:3;
+		uint64_t ring_en:1;
+		uint64_t reserved_17_19:3;
+		uint64_t ignrs:1;
+		uint64_t vs_wqe:1;
+		uint64_t vs_qos:1;
+		uint64_t l2_mal:1;
+		uint64_t tcp_flag:1;
+		uint64_t l4_len:1;
+		uint64_t l4_chk:1;
+		uint64_t l4_prt:1;
+		uint64_t l4_mal:1;
+		uint64_t reserved_6_7:2;
+		uint64_t ip6_eext:2;
+		uint64_t ip4_opts:1;
+		uint64_t ip_hop:1;
+		uint64_t ip_mal:1;
+		uint64_t ip_chk:1;
+#else
+		uint64_t ip_chk:1;
+		uint64_t ip_mal:1;
+		uint64_t ip_hop:1;
+		uint64_t ip4_opts:1;
+		uint64_t ip6_eext:2;
+		uint64_t reserved_6_7:2;
+		uint64_t l4_mal:1;
+		uint64_t l4_prt:1;
+		uint64_t l4_chk:1;
+		uint64_t l4_len:1;
+		uint64_t tcp_flag:1;
+		uint64_t l2_mal:1;
+		uint64_t vs_qos:1;
+		uint64_t vs_wqe:1;
+		uint64_t ignrs:1;
+		uint64_t reserved_17_19:3;
+		uint64_t ring_en:1;
+		uint64_t reserved_21_23:3;
+		uint64_t dsa_grp_sid:1;
+		uint64_t dsa_grp_scmd:1;
+		uint64_t dsa_grp_tvid:1;
+		uint64_t reserved_27_63:37;
+#endif
+	} cn52xx;
+	struct cvmx_pip_gbl_ctl_cn56xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_21_63:43;
+		uint64_t ring_en:1;
+		uint64_t reserved_17_19:3;
+		uint64_t ignrs:1;
+		uint64_t vs_wqe:1;
+		uint64_t vs_qos:1;
+		uint64_t l2_mal:1;
+		uint64_t tcp_flag:1;
+		uint64_t l4_len:1;
+		uint64_t l4_chk:1;
+		uint64_t l4_prt:1;
+		uint64_t l4_mal:1;
+		uint64_t reserved_6_7:2;
+		uint64_t ip6_eext:2;
+		uint64_t ip4_opts:1;
+		uint64_t ip_hop:1;
+		uint64_t ip_mal:1;
+		uint64_t ip_chk:1;
+#else
+		uint64_t ip_chk:1;
+		uint64_t ip_mal:1;
+		uint64_t ip_hop:1;
+		uint64_t ip4_opts:1;
+		uint64_t ip6_eext:2;
+		uint64_t reserved_6_7:2;
+		uint64_t l4_mal:1;
+		uint64_t l4_prt:1;
+		uint64_t l4_chk:1;
+		uint64_t l4_len:1;
+		uint64_t tcp_flag:1;
+		uint64_t l2_mal:1;
+		uint64_t vs_qos:1;
+		uint64_t vs_wqe:1;
+		uint64_t ignrs:1;
+		uint64_t reserved_17_19:3;
+		uint64_t ring_en:1;
+		uint64_t reserved_21_63:43;
+#endif
+	} cn56xxp1;
+	struct cvmx_pip_gbl_ctl_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_28_63:36;
+		uint64_t ihmsk_dis:1;
+		uint64_t dsa_grp_tvid:1;
+		uint64_t dsa_grp_scmd:1;
+		uint64_t dsa_grp_sid:1;
+		uint64_t reserved_21_23:3;
+		uint64_t ring_en:1;
+		uint64_t reserved_17_19:3;
+		uint64_t ignrs:1;
+		uint64_t vs_wqe:1;
+		uint64_t vs_qos:1;
+		uint64_t l2_mal:1;
+		uint64_t tcp_flag:1;
+		uint64_t l4_len:1;
+		uint64_t l4_chk:1;
+		uint64_t l4_prt:1;
+		uint64_t l4_mal:1;
+		uint64_t reserved_6_7:2;
+		uint64_t ip6_eext:2;
+		uint64_t ip4_opts:1;
+		uint64_t ip_hop:1;
+		uint64_t ip_mal:1;
+		uint64_t ip_chk:1;
+#else
+		uint64_t ip_chk:1;
+		uint64_t ip_mal:1;
+		uint64_t ip_hop:1;
+		uint64_t ip4_opts:1;
+		uint64_t ip6_eext:2;
+		uint64_t reserved_6_7:2;
+		uint64_t l4_mal:1;
+		uint64_t l4_prt:1;
+		uint64_t l4_chk:1;
+		uint64_t l4_len:1;
+		uint64_t tcp_flag:1;
+		uint64_t l2_mal:1;
+		uint64_t vs_qos:1;
+		uint64_t vs_wqe:1;
+		uint64_t ignrs:1;
+		uint64_t reserved_17_19:3;
+		uint64_t ring_en:1;
+		uint64_t reserved_21_23:3;
+		uint64_t dsa_grp_sid:1;
+		uint64_t dsa_grp_scmd:1;
+		uint64_t dsa_grp_tvid:1;
+		uint64_t ihmsk_dis:1;
+		uint64_t reserved_28_63:36;
+#endif
+	} cn61xx;
+	struct cvmx_pip_gbl_ctl_cn68xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t egrp_dis:1;
+		uint64_t ihmsk_dis:1;
+		uint64_t dsa_grp_tvid:1;
+		uint64_t dsa_grp_scmd:1;
+		uint64_t dsa_grp_sid:1;
+		uint64_t reserved_17_23:7;
+		uint64_t ignrs:1;
+		uint64_t vs_wqe:1;
+		uint64_t vs_qos:1;
+		uint64_t l2_mal:1;
+		uint64_t tcp_flag:1;
+		uint64_t l4_len:1;
+		uint64_t l4_chk:1;
+		uint64_t l4_prt:1;
+		uint64_t l4_mal:1;
+		uint64_t reserved_6_7:2;
+		uint64_t ip6_eext:2;
+		uint64_t ip4_opts:1;
+		uint64_t ip_hop:1;
+		uint64_t ip_mal:1;
+		uint64_t ip_chk:1;
+#else
+		uint64_t ip_chk:1;
+		uint64_t ip_mal:1;
+		uint64_t ip_hop:1;
+		uint64_t ip4_opts:1;
+		uint64_t ip6_eext:2;
+		uint64_t reserved_6_7:2;
+		uint64_t l4_mal:1;
+		uint64_t l4_prt:1;
+		uint64_t l4_chk:1;
+		uint64_t l4_len:1;
+		uint64_t tcp_flag:1;
+		uint64_t l2_mal:1;
+		uint64_t vs_qos:1;
+		uint64_t vs_wqe:1;
+		uint64_t ignrs:1;
+		uint64_t reserved_17_23:7;
+		uint64_t dsa_grp_sid:1;
+		uint64_t dsa_grp_scmd:1;
+		uint64_t dsa_grp_tvid:1;
+		uint64_t ihmsk_dis:1;
+		uint64_t egrp_dis:1;
+		uint64_t reserved_29_63:35;
+#endif
+	} cn68xx;
+	struct cvmx_pip_gbl_ctl_cn68xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_28_63:36;
+		uint64_t ihmsk_dis:1;
+		uint64_t dsa_grp_tvid:1;
+		uint64_t dsa_grp_scmd:1;
+		uint64_t dsa_grp_sid:1;
+		uint64_t reserved_17_23:7;
+		uint64_t ignrs:1;
+		uint64_t vs_wqe:1;
+		uint64_t vs_qos:1;
+		uint64_t l2_mal:1;
+		uint64_t tcp_flag:1;
+		uint64_t l4_len:1;
+		uint64_t l4_chk:1;
+		uint64_t l4_prt:1;
+		uint64_t l4_mal:1;
+		uint64_t reserved_6_7:2;
+		uint64_t ip6_eext:2;
+		uint64_t ip4_opts:1;
+		uint64_t ip_hop:1;
+		uint64_t ip_mal:1;
+		uint64_t ip_chk:1;
+#else
+		uint64_t ip_chk:1;
+		uint64_t ip_mal:1;
+		uint64_t ip_hop:1;
+		uint64_t ip4_opts:1;
+		uint64_t ip6_eext:2;
+		uint64_t reserved_6_7:2;
+		uint64_t l4_mal:1;
+		uint64_t l4_prt:1;
+		uint64_t l4_chk:1;
+		uint64_t l4_len:1;
+		uint64_t tcp_flag:1;
+		uint64_t l2_mal:1;
+		uint64_t vs_qos:1;
+		uint64_t vs_wqe:1;
+		uint64_t ignrs:1;
+		uint64_t reserved_17_23:7;
+		uint64_t dsa_grp_sid:1;
+		uint64_t dsa_grp_scmd:1;
+		uint64_t dsa_grp_tvid:1;
+		uint64_t ihmsk_dis:1;
+		uint64_t reserved_28_63:36;
+#endif
+	} cn68xxp1;
+};
+
+union cvmx_pip_hg_pri_qos {
+	uint64_t u64;
+	struct cvmx_pip_hg_pri_qos_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_13_63:51;
+		uint64_t up_qos:1;
+		uint64_t reserved_11_11:1;
+		uint64_t qos:3;
+		uint64_t reserved_6_7:2;
+		uint64_t pri:6;
+#else
+		uint64_t pri:6;
+		uint64_t reserved_6_7:2;
+		uint64_t qos:3;
+		uint64_t reserved_11_11:1;
+		uint64_t up_qos:1;
+		uint64_t reserved_13_63:51;
+#endif
+	} s;
+};
+
+union cvmx_pip_int_en {
+	uint64_t u64;
+	struct cvmx_pip_int_en_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_13_63:51;
+		uint64_t punyerr:1;
+		uint64_t lenerr:1;
+		uint64_t maxerr:1;
+		uint64_t minerr:1;
+		uint64_t beperr:1;
+		uint64_t feperr:1;
+		uint64_t todoovr:1;
+		uint64_t skprunt:1;
+		uint64_t badtag:1;
+		uint64_t prtnxa:1;
+		uint64_t bckprs:1;
+		uint64_t crcerr:1;
+		uint64_t pktdrp:1;
+#else
+		uint64_t pktdrp:1;
+		uint64_t crcerr:1;
+		uint64_t bckprs:1;
+		uint64_t prtnxa:1;
+		uint64_t badtag:1;
+		uint64_t skprunt:1;
+		uint64_t todoovr:1;
+		uint64_t feperr:1;
+		uint64_t beperr:1;
+		uint64_t minerr:1;
+		uint64_t maxerr:1;
+		uint64_t lenerr:1;
+		uint64_t punyerr:1;
+		uint64_t reserved_13_63:51;
+#endif
+	} s;
+	struct cvmx_pip_int_en_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_9_63:55;
+		uint64_t beperr:1;
+		uint64_t feperr:1;
+		uint64_t todoovr:1;
+		uint64_t skprunt:1;
+		uint64_t badtag:1;
+		uint64_t prtnxa:1;
+		uint64_t bckprs:1;
+		uint64_t crcerr:1;
+		uint64_t pktdrp:1;
+#else
+		uint64_t pktdrp:1;
+		uint64_t crcerr:1;
+		uint64_t bckprs:1;
+		uint64_t prtnxa:1;
+		uint64_t badtag:1;
+		uint64_t skprunt:1;
+		uint64_t todoovr:1;
+		uint64_t feperr:1;
+		uint64_t beperr:1;
+		uint64_t reserved_9_63:55;
+#endif
+	} cn30xx;
+	struct cvmx_pip_int_en_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t lenerr:1;
+		uint64_t maxerr:1;
+		uint64_t minerr:1;
+		uint64_t beperr:1;
+		uint64_t feperr:1;
+		uint64_t todoovr:1;
+		uint64_t skprunt:1;
+		uint64_t badtag:1;
+		uint64_t prtnxa:1;
+		uint64_t bckprs:1;
+		uint64_t reserved_1_1:1;
+		uint64_t pktdrp:1;
+#else
+		uint64_t pktdrp:1;
+		uint64_t reserved_1_1:1;
+		uint64_t bckprs:1;
+		uint64_t prtnxa:1;
+		uint64_t badtag:1;
+		uint64_t skprunt:1;
+		uint64_t todoovr:1;
+		uint64_t feperr:1;
+		uint64_t beperr:1;
+		uint64_t minerr:1;
+		uint64_t maxerr:1;
+		uint64_t lenerr:1;
+		uint64_t reserved_12_63:52;
+#endif
+	} cn50xx;
+	struct cvmx_pip_int_en_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_13_63:51;
+		uint64_t punyerr:1;
+		uint64_t lenerr:1;
+		uint64_t maxerr:1;
+		uint64_t minerr:1;
+		uint64_t beperr:1;
+		uint64_t feperr:1;
+		uint64_t todoovr:1;
+		uint64_t skprunt:1;
+		uint64_t badtag:1;
+		uint64_t prtnxa:1;
+		uint64_t bckprs:1;
+		uint64_t reserved_1_1:1;
+		uint64_t pktdrp:1;
+#else
+		uint64_t pktdrp:1;
+		uint64_t reserved_1_1:1;
+		uint64_t bckprs:1;
+		uint64_t prtnxa:1;
+		uint64_t badtag:1;
+		uint64_t skprunt:1;
+		uint64_t todoovr:1;
+		uint64_t feperr:1;
+		uint64_t beperr:1;
+		uint64_t minerr:1;
+		uint64_t maxerr:1;
+		uint64_t lenerr:1;
+		uint64_t punyerr:1;
+		uint64_t reserved_13_63:51;
+#endif
+	} cn52xx;
+	struct cvmx_pip_int_en_cn56xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t lenerr:1;
+		uint64_t maxerr:1;
+		uint64_t minerr:1;
+		uint64_t beperr:1;
+		uint64_t feperr:1;
+		uint64_t todoovr:1;
+		uint64_t skprunt:1;
+		uint64_t badtag:1;
+		uint64_t prtnxa:1;
+		uint64_t bckprs:1;
+		uint64_t crcerr:1;
+		uint64_t pktdrp:1;
+#else
+		uint64_t pktdrp:1;
+		uint64_t crcerr:1;
+		uint64_t bckprs:1;
+		uint64_t prtnxa:1;
+		uint64_t badtag:1;
+		uint64_t skprunt:1;
+		uint64_t todoovr:1;
+		uint64_t feperr:1;
+		uint64_t beperr:1;
+		uint64_t minerr:1;
+		uint64_t maxerr:1;
+		uint64_t lenerr:1;
+		uint64_t reserved_12_63:52;
+#endif
+	} cn56xxp1;
+	struct cvmx_pip_int_en_cn58xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_13_63:51;
+		uint64_t punyerr:1;
+		uint64_t reserved_9_11:3;
+		uint64_t beperr:1;
+		uint64_t feperr:1;
+		uint64_t todoovr:1;
+		uint64_t skprunt:1;
+		uint64_t badtag:1;
+		uint64_t prtnxa:1;
+		uint64_t bckprs:1;
+		uint64_t crcerr:1;
+		uint64_t pktdrp:1;
+#else
+		uint64_t pktdrp:1;
+		uint64_t crcerr:1;
+		uint64_t bckprs:1;
+		uint64_t prtnxa:1;
+		uint64_t badtag:1;
+		uint64_t skprunt:1;
+		uint64_t todoovr:1;
+		uint64_t feperr:1;
+		uint64_t beperr:1;
+		uint64_t reserved_9_11:3;
+		uint64_t punyerr:1;
+		uint64_t reserved_13_63:51;
+#endif
+	} cn58xx;
+};
+
+union cvmx_pip_int_reg {
+	uint64_t u64;
+	struct cvmx_pip_int_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_13_63:51;
+		uint64_t punyerr:1;
+		uint64_t lenerr:1;
+		uint64_t maxerr:1;
+		uint64_t minerr:1;
+		uint64_t beperr:1;
+		uint64_t feperr:1;
+		uint64_t todoovr:1;
+		uint64_t skprunt:1;
+		uint64_t badtag:1;
+		uint64_t prtnxa:1;
+		uint64_t bckprs:1;
+		uint64_t crcerr:1;
+		uint64_t pktdrp:1;
+#else
+		uint64_t pktdrp:1;
+		uint64_t crcerr:1;
+		uint64_t bckprs:1;
+		uint64_t prtnxa:1;
+		uint64_t badtag:1;
+		uint64_t skprunt:1;
+		uint64_t todoovr:1;
+		uint64_t feperr:1;
+		uint64_t beperr:1;
+		uint64_t minerr:1;
+		uint64_t maxerr:1;
+		uint64_t lenerr:1;
+		uint64_t punyerr:1;
+		uint64_t reserved_13_63:51;
+#endif
+	} s;
+	struct cvmx_pip_int_reg_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_9_63:55;
+		uint64_t beperr:1;
+		uint64_t feperr:1;
+		uint64_t todoovr:1;
+		uint64_t skprunt:1;
+		uint64_t badtag:1;
+		uint64_t prtnxa:1;
+		uint64_t bckprs:1;
+		uint64_t crcerr:1;
+		uint64_t pktdrp:1;
+#else
+		uint64_t pktdrp:1;
+		uint64_t crcerr:1;
+		uint64_t bckprs:1;
+		uint64_t prtnxa:1;
+		uint64_t badtag:1;
+		uint64_t skprunt:1;
+		uint64_t todoovr:1;
+		uint64_t feperr:1;
+		uint64_t beperr:1;
+		uint64_t reserved_9_63:55;
+#endif
+	} cn30xx;
+	struct cvmx_pip_int_reg_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t lenerr:1;
+		uint64_t maxerr:1;
+		uint64_t minerr:1;
+		uint64_t beperr:1;
+		uint64_t feperr:1;
+		uint64_t todoovr:1;
+		uint64_t skprunt:1;
+		uint64_t badtag:1;
+		uint64_t prtnxa:1;
+		uint64_t bckprs:1;
+		uint64_t reserved_1_1:1;
+		uint64_t pktdrp:1;
+#else
+		uint64_t pktdrp:1;
+		uint64_t reserved_1_1:1;
+		uint64_t bckprs:1;
+		uint64_t prtnxa:1;
+		uint64_t badtag:1;
+		uint64_t skprunt:1;
+		uint64_t todoovr:1;
+		uint64_t feperr:1;
+		uint64_t beperr:1;
+		uint64_t minerr:1;
+		uint64_t maxerr:1;
+		uint64_t lenerr:1;
+		uint64_t reserved_12_63:52;
+#endif
+	} cn50xx;
+	struct cvmx_pip_int_reg_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_13_63:51;
+		uint64_t punyerr:1;
+		uint64_t lenerr:1;
+		uint64_t maxerr:1;
+		uint64_t minerr:1;
+		uint64_t beperr:1;
+		uint64_t feperr:1;
+		uint64_t todoovr:1;
+		uint64_t skprunt:1;
+		uint64_t badtag:1;
+		uint64_t prtnxa:1;
+		uint64_t bckprs:1;
+		uint64_t reserved_1_1:1;
+		uint64_t pktdrp:1;
+#else
+		uint64_t pktdrp:1;
+		uint64_t reserved_1_1:1;
+		uint64_t bckprs:1;
+		uint64_t prtnxa:1;
+		uint64_t badtag:1;
+		uint64_t skprunt:1;
+		uint64_t todoovr:1;
+		uint64_t feperr:1;
+		uint64_t beperr:1;
+		uint64_t minerr:1;
+		uint64_t maxerr:1;
+		uint64_t lenerr:1;
+		uint64_t punyerr:1;
+		uint64_t reserved_13_63:51;
+#endif
+	} cn52xx;
+	struct cvmx_pip_int_reg_cn56xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t lenerr:1;
+		uint64_t maxerr:1;
+		uint64_t minerr:1;
+		uint64_t beperr:1;
+		uint64_t feperr:1;
+		uint64_t todoovr:1;
+		uint64_t skprunt:1;
+		uint64_t badtag:1;
+		uint64_t prtnxa:1;
+		uint64_t bckprs:1;
+		uint64_t crcerr:1;
+		uint64_t pktdrp:1;
+#else
+		uint64_t pktdrp:1;
+		uint64_t crcerr:1;
+		uint64_t bckprs:1;
+		uint64_t prtnxa:1;
+		uint64_t badtag:1;
+		uint64_t skprunt:1;
+		uint64_t todoovr:1;
+		uint64_t feperr:1;
+		uint64_t beperr:1;
+		uint64_t minerr:1;
+		uint64_t maxerr:1;
+		uint64_t lenerr:1;
+		uint64_t reserved_12_63:52;
+#endif
+	} cn56xxp1;
+	struct cvmx_pip_int_reg_cn58xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_13_63:51;
+		uint64_t punyerr:1;
+		uint64_t reserved_9_11:3;
+		uint64_t beperr:1;
+		uint64_t feperr:1;
+		uint64_t todoovr:1;
+		uint64_t skprunt:1;
+		uint64_t badtag:1;
+		uint64_t prtnxa:1;
+		uint64_t bckprs:1;
+		uint64_t crcerr:1;
+		uint64_t pktdrp:1;
+#else
+		uint64_t pktdrp:1;
+		uint64_t crcerr:1;
+		uint64_t bckprs:1;
+		uint64_t prtnxa:1;
+		uint64_t badtag:1;
+		uint64_t skprunt:1;
+		uint64_t todoovr:1;
+		uint64_t feperr:1;
+		uint64_t beperr:1;
+		uint64_t reserved_9_11:3;
+		uint64_t punyerr:1;
+		uint64_t reserved_13_63:51;
+#endif
+	} cn58xx;
+};
+
+union cvmx_pip_ip_offset {
+	uint64_t u64;
+	struct cvmx_pip_ip_offset_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_3_63:61;
+		uint64_t offset:3;
+#else
+		uint64_t offset:3;
+		uint64_t reserved_3_63:61;
+#endif
+	} s;
+};
+
+union cvmx_pip_pri_tblx {
+	uint64_t u64;
+	struct cvmx_pip_pri_tblx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t diff2_padd:8;
+		uint64_t hg2_padd:8;
+		uint64_t vlan2_padd:8;
+		uint64_t reserved_38_39:2;
+		uint64_t diff2_bpid:6;
+		uint64_t reserved_30_31:2;
+		uint64_t hg2_bpid:6;
+		uint64_t reserved_22_23:2;
+		uint64_t vlan2_bpid:6;
+		uint64_t reserved_11_15:5;
+		uint64_t diff2_qos:3;
+		uint64_t reserved_7_7:1;
+		uint64_t hg2_qos:3;
+		uint64_t reserved_3_3:1;
+		uint64_t vlan2_qos:3;
+#else
+		uint64_t vlan2_qos:3;
+		uint64_t reserved_3_3:1;
+		uint64_t hg2_qos:3;
+		uint64_t reserved_7_7:1;
+		uint64_t diff2_qos:3;
+		uint64_t reserved_11_15:5;
+		uint64_t vlan2_bpid:6;
+		uint64_t reserved_22_23:2;
+		uint64_t hg2_bpid:6;
+		uint64_t reserved_30_31:2;
+		uint64_t diff2_bpid:6;
+		uint64_t reserved_38_39:2;
+		uint64_t vlan2_padd:8;
+		uint64_t hg2_padd:8;
+		uint64_t diff2_padd:8;
+#endif
+	} s;
+};
+
+union cvmx_pip_prt_cfgx {
+	uint64_t u64;
+	struct cvmx_pip_prt_cfgx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_55_63:9;
+		uint64_t ih_pri:1;
+		uint64_t len_chk_sel:1;
+		uint64_t pad_len:1;
+		uint64_t vlan_len:1;
+		uint64_t lenerr_en:1;
+		uint64_t maxerr_en:1;
+		uint64_t minerr_en:1;
+		uint64_t grp_wat_47:4;
+		uint64_t qos_wat_47:4;
+		uint64_t reserved_37_39:3;
+		uint64_t rawdrp:1;
+		uint64_t tag_inc:2;
+		uint64_t dyn_rs:1;
+		uint64_t inst_hdr:1;
+		uint64_t grp_wat:4;
+		uint64_t hg_qos:1;
+		uint64_t qos:3;
+		uint64_t qos_wat:4;
+		uint64_t qos_vsel:1;
+		uint64_t qos_vod:1;
+		uint64_t qos_diff:1;
+		uint64_t qos_vlan:1;
+		uint64_t reserved_13_15:3;
+		uint64_t crc_en:1;
+		uint64_t higig_en:1;
+		uint64_t dsa_en:1;
+		uint64_t mode:2;
+		uint64_t reserved_7_7:1;
+		uint64_t skip:7;
+#else
+		uint64_t skip:7;
+		uint64_t reserved_7_7:1;
+		uint64_t mode:2;
+		uint64_t dsa_en:1;
+		uint64_t higig_en:1;
+		uint64_t crc_en:1;
+		uint64_t reserved_13_15:3;
+		uint64_t qos_vlan:1;
+		uint64_t qos_diff:1;
+		uint64_t qos_vod:1;
+		uint64_t qos_vsel:1;
+		uint64_t qos_wat:4;
+		uint64_t qos:3;
+		uint64_t hg_qos:1;
+		uint64_t grp_wat:4;
+		uint64_t inst_hdr:1;
+		uint64_t dyn_rs:1;
+		uint64_t tag_inc:2;
+		uint64_t rawdrp:1;
+		uint64_t reserved_37_39:3;
+		uint64_t qos_wat_47:4;
+		uint64_t grp_wat_47:4;
+		uint64_t minerr_en:1;
+		uint64_t maxerr_en:1;
+		uint64_t lenerr_en:1;
+		uint64_t vlan_len:1;
+		uint64_t pad_len:1;
+		uint64_t len_chk_sel:1;
+		uint64_t ih_pri:1;
+		uint64_t reserved_55_63:9;
+#endif
+	} s;
+	struct cvmx_pip_prt_cfgx_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_37_63:27;
+		uint64_t rawdrp:1;
+		uint64_t tag_inc:2;
+		uint64_t dyn_rs:1;
+		uint64_t inst_hdr:1;
+		uint64_t grp_wat:4;
+		uint64_t reserved_27_27:1;
+		uint64_t qos:3;
+		uint64_t qos_wat:4;
+		uint64_t reserved_18_19:2;
+		uint64_t qos_diff:1;
+		uint64_t qos_vlan:1;
+		uint64_t reserved_10_15:6;
+		uint64_t mode:2;
+		uint64_t reserved_7_7:1;
+		uint64_t skip:7;
+#else
+		uint64_t skip:7;
+		uint64_t reserved_7_7:1;
+		uint64_t mode:2;
+		uint64_t reserved_10_15:6;
+		uint64_t qos_vlan:1;
+		uint64_t qos_diff:1;
+		uint64_t reserved_18_19:2;
+		uint64_t qos_wat:4;
+		uint64_t qos:3;
+		uint64_t reserved_27_27:1;
+		uint64_t grp_wat:4;
+		uint64_t inst_hdr:1;
+		uint64_t dyn_rs:1;
+		uint64_t tag_inc:2;
+		uint64_t rawdrp:1;
+		uint64_t reserved_37_63:27;
+#endif
+	} cn30xx;
+	struct cvmx_pip_prt_cfgx_cn38xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_37_63:27;
+		uint64_t rawdrp:1;
+		uint64_t tag_inc:2;
+		uint64_t dyn_rs:1;
+		uint64_t inst_hdr:1;
+		uint64_t grp_wat:4;
+		uint64_t reserved_27_27:1;
+		uint64_t qos:3;
+		uint64_t qos_wat:4;
+		uint64_t reserved_18_19:2;
+		uint64_t qos_diff:1;
+		uint64_t qos_vlan:1;
+		uint64_t reserved_13_15:3;
+		uint64_t crc_en:1;
+		uint64_t reserved_10_11:2;
+		uint64_t mode:2;
+		uint64_t reserved_7_7:1;
+		uint64_t skip:7;
+#else
+		uint64_t skip:7;
+		uint64_t reserved_7_7:1;
+		uint64_t mode:2;
+		uint64_t reserved_10_11:2;
+		uint64_t crc_en:1;
+		uint64_t reserved_13_15:3;
+		uint64_t qos_vlan:1;
+		uint64_t qos_diff:1;
+		uint64_t reserved_18_19:2;
+		uint64_t qos_wat:4;
+		uint64_t qos:3;
+		uint64_t reserved_27_27:1;
+		uint64_t grp_wat:4;
+		uint64_t inst_hdr:1;
+		uint64_t dyn_rs:1;
+		uint64_t tag_inc:2;
+		uint64_t rawdrp:1;
+		uint64_t reserved_37_63:27;
+#endif
+	} cn38xx;
+	struct cvmx_pip_prt_cfgx_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_53_63:11;
+		uint64_t pad_len:1;
+		uint64_t vlan_len:1;
+		uint64_t lenerr_en:1;
+		uint64_t maxerr_en:1;
+		uint64_t minerr_en:1;
+		uint64_t grp_wat_47:4;
+		uint64_t qos_wat_47:4;
+		uint64_t reserved_37_39:3;
+		uint64_t rawdrp:1;
+		uint64_t tag_inc:2;
+		uint64_t dyn_rs:1;
+		uint64_t inst_hdr:1;
+		uint64_t grp_wat:4;
+		uint64_t reserved_27_27:1;
+		uint64_t qos:3;
+		uint64_t qos_wat:4;
+		uint64_t reserved_19_19:1;
+		uint64_t qos_vod:1;
+		uint64_t qos_diff:1;
+		uint64_t qos_vlan:1;
+		uint64_t reserved_13_15:3;
+		uint64_t crc_en:1;
+		uint64_t reserved_10_11:2;
+		uint64_t mode:2;
+		uint64_t reserved_7_7:1;
+		uint64_t skip:7;
+#else
+		uint64_t skip:7;
+		uint64_t reserved_7_7:1;
+		uint64_t mode:2;
+		uint64_t reserved_10_11:2;
+		uint64_t crc_en:1;
+		uint64_t reserved_13_15:3;
+		uint64_t qos_vlan:1;
+		uint64_t qos_diff:1;
+		uint64_t qos_vod:1;
+		uint64_t reserved_19_19:1;
+		uint64_t qos_wat:4;
+		uint64_t qos:3;
+		uint64_t reserved_27_27:1;
+		uint64_t grp_wat:4;
+		uint64_t inst_hdr:1;
+		uint64_t dyn_rs:1;
+		uint64_t tag_inc:2;
+		uint64_t rawdrp:1;
+		uint64_t reserved_37_39:3;
+		uint64_t qos_wat_47:4;
+		uint64_t grp_wat_47:4;
+		uint64_t minerr_en:1;
+		uint64_t maxerr_en:1;
+		uint64_t lenerr_en:1;
+		uint64_t vlan_len:1;
+		uint64_t pad_len:1;
+		uint64_t reserved_53_63:11;
+#endif
+	} cn50xx;
+	struct cvmx_pip_prt_cfgx_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_53_63:11;
+		uint64_t pad_len:1;
+		uint64_t vlan_len:1;
+		uint64_t lenerr_en:1;
+		uint64_t maxerr_en:1;
+		uint64_t minerr_en:1;
+		uint64_t grp_wat_47:4;
+		uint64_t qos_wat_47:4;
+		uint64_t reserved_37_39:3;
+		uint64_t rawdrp:1;
+		uint64_t tag_inc:2;
+		uint64_t dyn_rs:1;
+		uint64_t inst_hdr:1;
+		uint64_t grp_wat:4;
+		uint64_t hg_qos:1;
+		uint64_t qos:3;
+		uint64_t qos_wat:4;
+		uint64_t qos_vsel:1;
+		uint64_t qos_vod:1;
+		uint64_t qos_diff:1;
+		uint64_t qos_vlan:1;
+		uint64_t reserved_13_15:3;
+		uint64_t crc_en:1;
+		uint64_t higig_en:1;
+		uint64_t dsa_en:1;
+		uint64_t mode:2;
+		uint64_t reserved_7_7:1;
+		uint64_t skip:7;
+#else
+		uint64_t skip:7;
+		uint64_t reserved_7_7:1;
+		uint64_t mode:2;
+		uint64_t dsa_en:1;
+		uint64_t higig_en:1;
+		uint64_t crc_en:1;
+		uint64_t reserved_13_15:3;
+		uint64_t qos_vlan:1;
+		uint64_t qos_diff:1;
+		uint64_t qos_vod:1;
+		uint64_t qos_vsel:1;
+		uint64_t qos_wat:4;
+		uint64_t qos:3;
+		uint64_t hg_qos:1;
+		uint64_t grp_wat:4;
+		uint64_t inst_hdr:1;
+		uint64_t dyn_rs:1;
+		uint64_t tag_inc:2;
+		uint64_t rawdrp:1;
+		uint64_t reserved_37_39:3;
+		uint64_t qos_wat_47:4;
+		uint64_t grp_wat_47:4;
+		uint64_t minerr_en:1;
+		uint64_t maxerr_en:1;
+		uint64_t lenerr_en:1;
+		uint64_t vlan_len:1;
+		uint64_t pad_len:1;
+		uint64_t reserved_53_63:11;
+#endif
+	} cn52xx;
+	struct cvmx_pip_prt_cfgx_cn58xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_37_63:27;
+		uint64_t rawdrp:1;
+		uint64_t tag_inc:2;
+		uint64_t dyn_rs:1;
+		uint64_t inst_hdr:1;
+		uint64_t grp_wat:4;
+		uint64_t reserved_27_27:1;
+		uint64_t qos:3;
+		uint64_t qos_wat:4;
+		uint64_t reserved_19_19:1;
+		uint64_t qos_vod:1;
+		uint64_t qos_diff:1;
+		uint64_t qos_vlan:1;
+		uint64_t reserved_13_15:3;
+		uint64_t crc_en:1;
+		uint64_t reserved_10_11:2;
+		uint64_t mode:2;
+		uint64_t reserved_7_7:1;
+		uint64_t skip:7;
+#else
+		uint64_t skip:7;
+		uint64_t reserved_7_7:1;
+		uint64_t mode:2;
+		uint64_t reserved_10_11:2;
+		uint64_t crc_en:1;
+		uint64_t reserved_13_15:3;
+		uint64_t qos_vlan:1;
+		uint64_t qos_diff:1;
+		uint64_t qos_vod:1;
+		uint64_t reserved_19_19:1;
+		uint64_t qos_wat:4;
+		uint64_t qos:3;
+		uint64_t reserved_27_27:1;
+		uint64_t grp_wat:4;
+		uint64_t inst_hdr:1;
+		uint64_t dyn_rs:1;
+		uint64_t tag_inc:2;
+		uint64_t rawdrp:1;
+		uint64_t reserved_37_63:27;
+#endif
+	} cn58xx;
+	struct cvmx_pip_prt_cfgx_cn68xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_55_63:9;
+		uint64_t ih_pri:1;
+		uint64_t len_chk_sel:1;
+		uint64_t pad_len:1;
+		uint64_t vlan_len:1;
+		uint64_t lenerr_en:1;
+		uint64_t maxerr_en:1;
+		uint64_t minerr_en:1;
+		uint64_t grp_wat_47:4;
+		uint64_t qos_wat_47:4;
+		uint64_t reserved_37_39:3;
+		uint64_t rawdrp:1;
+		uint64_t tag_inc:2;
+		uint64_t dyn_rs:1;
+		uint64_t inst_hdr:1;
+		uint64_t grp_wat:4;
+		uint64_t hg_qos:1;
+		uint64_t qos:3;
+		uint64_t qos_wat:4;
+		uint64_t reserved_19_19:1;
+		uint64_t qos_vod:1;
+		uint64_t qos_diff:1;
+		uint64_t qos_vlan:1;
+		uint64_t reserved_13_15:3;
+		uint64_t crc_en:1;
+		uint64_t higig_en:1;
+		uint64_t dsa_en:1;
+		uint64_t mode:2;
+		uint64_t reserved_7_7:1;
+		uint64_t skip:7;
+#else
+		uint64_t skip:7;
+		uint64_t reserved_7_7:1;
+		uint64_t mode:2;
+		uint64_t dsa_en:1;
+		uint64_t higig_en:1;
+		uint64_t crc_en:1;
+		uint64_t reserved_13_15:3;
+		uint64_t qos_vlan:1;
+		uint64_t qos_diff:1;
+		uint64_t qos_vod:1;
+		uint64_t reserved_19_19:1;
+		uint64_t qos_wat:4;
+		uint64_t qos:3;
+		uint64_t hg_qos:1;
+		uint64_t grp_wat:4;
+		uint64_t inst_hdr:1;
+		uint64_t dyn_rs:1;
+		uint64_t tag_inc:2;
+		uint64_t rawdrp:1;
+		uint64_t reserved_37_39:3;
+		uint64_t qos_wat_47:4;
+		uint64_t grp_wat_47:4;
+		uint64_t minerr_en:1;
+		uint64_t maxerr_en:1;
+		uint64_t lenerr_en:1;
+		uint64_t vlan_len:1;
+		uint64_t pad_len:1;
+		uint64_t len_chk_sel:1;
+		uint64_t ih_pri:1;
+		uint64_t reserved_55_63:9;
+#endif
+	} cn68xx;
+};
+
+union cvmx_pip_prt_cfgbx {
+	uint64_t u64;
+	struct cvmx_pip_prt_cfgbx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_39_63:25;
+		uint64_t alt_skp_sel:2;
+		uint64_t alt_skp_en:1;
+		uint64_t reserved_35_35:1;
+		uint64_t bsel_num:2;
+		uint64_t bsel_en:1;
+		uint64_t reserved_24_31:8;
+		uint64_t base:8;
+		uint64_t reserved_6_15:10;
+		uint64_t bpid:6;
+#else
+		uint64_t bpid:6;
+		uint64_t reserved_6_15:10;
+		uint64_t base:8;
+		uint64_t reserved_24_31:8;
+		uint64_t bsel_en:1;
+		uint64_t bsel_num:2;
+		uint64_t reserved_35_35:1;
+		uint64_t alt_skp_en:1;
+		uint64_t alt_skp_sel:2;
+		uint64_t reserved_39_63:25;
+#endif
+	} s;
+	struct cvmx_pip_prt_cfgbx_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_39_63:25;
+		uint64_t alt_skp_sel:2;
+		uint64_t alt_skp_en:1;
+		uint64_t reserved_35_35:1;
+		uint64_t bsel_num:2;
+		uint64_t bsel_en:1;
+		uint64_t reserved_0_31:32;
+#else
+		uint64_t reserved_0_31:32;
+		uint64_t bsel_en:1;
+		uint64_t bsel_num:2;
+		uint64_t reserved_35_35:1;
+		uint64_t alt_skp_en:1;
+		uint64_t alt_skp_sel:2;
+		uint64_t reserved_39_63:25;
+#endif
+	} cn61xx;
+	struct cvmx_pip_prt_cfgbx_cn66xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_39_63:25;
+		uint64_t alt_skp_sel:2;
+		uint64_t alt_skp_en:1;
+		uint64_t reserved_0_35:36;
+#else
+		uint64_t reserved_0_35:36;
+		uint64_t alt_skp_en:1;
+		uint64_t alt_skp_sel:2;
+		uint64_t reserved_39_63:25;
+#endif
+	} cn66xx;
+	struct cvmx_pip_prt_cfgbx_cn68xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_24_63:40;
+		uint64_t base:8;
+		uint64_t reserved_6_15:10;
+		uint64_t bpid:6;
+#else
+		uint64_t bpid:6;
+		uint64_t reserved_6_15:10;
+		uint64_t base:8;
+		uint64_t reserved_24_63:40;
+#endif
+	} cn68xxp1;
+};
+
+union cvmx_pip_prt_tagx {
+	uint64_t u64;
+	struct cvmx_pip_prt_tagx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_54_63:10;
+		uint64_t portadd_en:1;
+		uint64_t inc_hwchk:1;
+		uint64_t reserved_50_51:2;
+		uint64_t grptagbase_msb:2;
+		uint64_t reserved_46_47:2;
+		uint64_t grptagmask_msb:2;
+		uint64_t reserved_42_43:2;
+		uint64_t grp_msb:2;
+		uint64_t grptagbase:4;
+		uint64_t grptagmask:4;
+		uint64_t grptag:1;
+		uint64_t grptag_mskip:1;
+		uint64_t tag_mode:2;
+		uint64_t inc_vs:2;
+		uint64_t inc_vlan:1;
+		uint64_t inc_prt_flag:1;
+		uint64_t ip6_dprt_flag:1;
+		uint64_t ip4_dprt_flag:1;
+		uint64_t ip6_sprt_flag:1;
+		uint64_t ip4_sprt_flag:1;
+		uint64_t ip6_nxth_flag:1;
+		uint64_t ip4_pctl_flag:1;
+		uint64_t ip6_dst_flag:1;
+		uint64_t ip4_dst_flag:1;
+		uint64_t ip6_src_flag:1;
+		uint64_t ip4_src_flag:1;
+		uint64_t tcp6_tag_type:2;
+		uint64_t tcp4_tag_type:2;
+		uint64_t ip6_tag_type:2;
+		uint64_t ip4_tag_type:2;
+		uint64_t non_tag_type:2;
+		uint64_t grp:4;
+#else
+		uint64_t grp:4;
+		uint64_t non_tag_type:2;
+		uint64_t ip4_tag_type:2;
+		uint64_t ip6_tag_type:2;
+		uint64_t tcp4_tag_type:2;
+		uint64_t tcp6_tag_type:2;
+		uint64_t ip4_src_flag:1;
+		uint64_t ip6_src_flag:1;
+		uint64_t ip4_dst_flag:1;
+		uint64_t ip6_dst_flag:1;
+		uint64_t ip4_pctl_flag:1;
+		uint64_t ip6_nxth_flag:1;
+		uint64_t ip4_sprt_flag:1;
+		uint64_t ip6_sprt_flag:1;
+		uint64_t ip4_dprt_flag:1;
+		uint64_t ip6_dprt_flag:1;
+		uint64_t inc_prt_flag:1;
+		uint64_t inc_vlan:1;
+		uint64_t inc_vs:2;
+		uint64_t tag_mode:2;
+		uint64_t grptag_mskip:1;
+		uint64_t grptag:1;
+		uint64_t grptagmask:4;
+		uint64_t grptagbase:4;
+		uint64_t grp_msb:2;
+		uint64_t reserved_42_43:2;
+		uint64_t grptagmask_msb:2;
+		uint64_t reserved_46_47:2;
+		uint64_t grptagbase_msb:2;
+		uint64_t reserved_50_51:2;
+		uint64_t inc_hwchk:1;
+		uint64_t portadd_en:1;
+		uint64_t reserved_54_63:10;
+#endif
+	} s;
+	struct cvmx_pip_prt_tagx_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_40_63:24;
+		uint64_t grptagbase:4;
+		uint64_t grptagmask:4;
+		uint64_t grptag:1;
+		uint64_t reserved_30_30:1;
+		uint64_t tag_mode:2;
+		uint64_t inc_vs:2;
+		uint64_t inc_vlan:1;
+		uint64_t inc_prt_flag:1;
+		uint64_t ip6_dprt_flag:1;
+		uint64_t ip4_dprt_flag:1;
+		uint64_t ip6_sprt_flag:1;
+		uint64_t ip4_sprt_flag:1;
+		uint64_t ip6_nxth_flag:1;
+		uint64_t ip4_pctl_flag:1;
+		uint64_t ip6_dst_flag:1;
+		uint64_t ip4_dst_flag:1;
+		uint64_t ip6_src_flag:1;
+		uint64_t ip4_src_flag:1;
+		uint64_t tcp6_tag_type:2;
+		uint64_t tcp4_tag_type:2;
+		uint64_t ip6_tag_type:2;
+		uint64_t ip4_tag_type:2;
+		uint64_t non_tag_type:2;
+		uint64_t grp:4;
+#else
+		uint64_t grp:4;
+		uint64_t non_tag_type:2;
+		uint64_t ip4_tag_type:2;
+		uint64_t ip6_tag_type:2;
+		uint64_t tcp4_tag_type:2;
+		uint64_t tcp6_tag_type:2;
+		uint64_t ip4_src_flag:1;
+		uint64_t ip6_src_flag:1;
+		uint64_t ip4_dst_flag:1;
+		uint64_t ip6_dst_flag:1;
+		uint64_t ip4_pctl_flag:1;
+		uint64_t ip6_nxth_flag:1;
+		uint64_t ip4_sprt_flag:1;
+		uint64_t ip6_sprt_flag:1;
+		uint64_t ip4_dprt_flag:1;
+		uint64_t ip6_dprt_flag:1;
+		uint64_t inc_prt_flag:1;
+		uint64_t inc_vlan:1;
+		uint64_t inc_vs:2;
+		uint64_t tag_mode:2;
+		uint64_t reserved_30_30:1;
+		uint64_t grptag:1;
+		uint64_t grptagmask:4;
+		uint64_t grptagbase:4;
+		uint64_t reserved_40_63:24;
+#endif
+	} cn30xx;
+	struct cvmx_pip_prt_tagx_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_40_63:24;
+		uint64_t grptagbase:4;
+		uint64_t grptagmask:4;
+		uint64_t grptag:1;
+		uint64_t grptag_mskip:1;
+		uint64_t tag_mode:2;
+		uint64_t inc_vs:2;
+		uint64_t inc_vlan:1;
+		uint64_t inc_prt_flag:1;
+		uint64_t ip6_dprt_flag:1;
+		uint64_t ip4_dprt_flag:1;
+		uint64_t ip6_sprt_flag:1;
+		uint64_t ip4_sprt_flag:1;
+		uint64_t ip6_nxth_flag:1;
+		uint64_t ip4_pctl_flag:1;
+		uint64_t ip6_dst_flag:1;
+		uint64_t ip4_dst_flag:1;
+		uint64_t ip6_src_flag:1;
+		uint64_t ip4_src_flag:1;
+		uint64_t tcp6_tag_type:2;
+		uint64_t tcp4_tag_type:2;
+		uint64_t ip6_tag_type:2;
+		uint64_t ip4_tag_type:2;
+		uint64_t non_tag_type:2;
+		uint64_t grp:4;
+#else
+		uint64_t grp:4;
+		uint64_t non_tag_type:2;
+		uint64_t ip4_tag_type:2;
+		uint64_t ip6_tag_type:2;
+		uint64_t tcp4_tag_type:2;
+		uint64_t tcp6_tag_type:2;
+		uint64_t ip4_src_flag:1;
+		uint64_t ip6_src_flag:1;
+		uint64_t ip4_dst_flag:1;
+		uint64_t ip6_dst_flag:1;
+		uint64_t ip4_pctl_flag:1;
+		uint64_t ip6_nxth_flag:1;
+		uint64_t ip4_sprt_flag:1;
+		uint64_t ip6_sprt_flag:1;
+		uint64_t ip4_dprt_flag:1;
+		uint64_t ip6_dprt_flag:1;
+		uint64_t inc_prt_flag:1;
+		uint64_t inc_vlan:1;
+		uint64_t inc_vs:2;
+		uint64_t tag_mode:2;
+		uint64_t grptag_mskip:1;
+		uint64_t grptag:1;
+		uint64_t grptagmask:4;
+		uint64_t grptagbase:4;
+		uint64_t reserved_40_63:24;
+#endif
+	} cn50xx;
+};
+
+union cvmx_pip_qos_diffx {
+	uint64_t u64;
+	struct cvmx_pip_qos_diffx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_3_63:61;
+		uint64_t qos:3;
+#else
+		uint64_t qos:3;
+		uint64_t reserved_3_63:61;
+#endif
+	} s;
+};
+
+union cvmx_pip_qos_vlanx {
+	uint64_t u64;
+	struct cvmx_pip_qos_vlanx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t qos1:3;
+		uint64_t reserved_3_3:1;
+		uint64_t qos:3;
+#else
+		uint64_t qos:3;
+		uint64_t reserved_3_3:1;
+		uint64_t qos1:3;
+		uint64_t reserved_7_63:57;
+#endif
+	} s;
+	struct cvmx_pip_qos_vlanx_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_3_63:61;
+		uint64_t qos:3;
+#else
+		uint64_t qos:3;
+		uint64_t reserved_3_63:61;
+#endif
+	} cn30xx;
+};
+
+union cvmx_pip_qos_watchx {
+	uint64_t u64;
+	struct cvmx_pip_qos_watchx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t mask:16;
+		uint64_t reserved_30_31:2;
+		uint64_t grp:6;
+		uint64_t reserved_23_23:1;
+		uint64_t qos:3;
+		uint64_t reserved_19_19:1;
+		uint64_t match_type:3;
+		uint64_t match_value:16;
+#else
+		uint64_t match_value:16;
+		uint64_t match_type:3;
+		uint64_t reserved_19_19:1;
+		uint64_t qos:3;
+		uint64_t reserved_23_23:1;
+		uint64_t grp:6;
+		uint64_t reserved_30_31:2;
+		uint64_t mask:16;
+		uint64_t reserved_48_63:16;
+#endif
+	} s;
+	struct cvmx_pip_qos_watchx_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t mask:16;
+		uint64_t reserved_28_31:4;
+		uint64_t grp:4;
+		uint64_t reserved_23_23:1;
+		uint64_t qos:3;
+		uint64_t reserved_18_19:2;
+		uint64_t match_type:2;
+		uint64_t match_value:16;
+#else
+		uint64_t match_value:16;
+		uint64_t match_type:2;
+		uint64_t reserved_18_19:2;
+		uint64_t qos:3;
+		uint64_t reserved_23_23:1;
+		uint64_t grp:4;
+		uint64_t reserved_28_31:4;
+		uint64_t mask:16;
+		uint64_t reserved_48_63:16;
+#endif
+	} cn30xx;
+	struct cvmx_pip_qos_watchx_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t mask:16;
+		uint64_t reserved_28_31:4;
+		uint64_t grp:4;
+		uint64_t reserved_23_23:1;
+		uint64_t qos:3;
+		uint64_t reserved_19_19:1;
+		uint64_t match_type:3;
+		uint64_t match_value:16;
+#else
+		uint64_t match_value:16;
+		uint64_t match_type:3;
+		uint64_t reserved_19_19:1;
+		uint64_t qos:3;
+		uint64_t reserved_23_23:1;
+		uint64_t grp:4;
+		uint64_t reserved_28_31:4;
+		uint64_t mask:16;
+		uint64_t reserved_48_63:16;
+#endif
+	} cn50xx;
+};
+
+union cvmx_pip_raw_word {
+	uint64_t u64;
+	struct cvmx_pip_raw_word_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_56_63:8;
+		uint64_t word:56;
+#else
+		uint64_t word:56;
+		uint64_t reserved_56_63:8;
+#endif
+	} s;
+};
+
+union cvmx_pip_sft_rst {
+	uint64_t u64;
+	struct cvmx_pip_sft_rst_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t rst:1;
+#else
+		uint64_t rst:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_pip_stat0_x {
+	uint64_t u64;
+	struct cvmx_pip_stat0_x_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t drp_pkts:32;
+		uint64_t drp_octs:32;
+#else
+		uint64_t drp_octs:32;
+		uint64_t drp_pkts:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_stat0_prtx {
+	uint64_t u64;
+	struct cvmx_pip_stat0_prtx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t drp_pkts:32;
+		uint64_t drp_octs:32;
+#else
+		uint64_t drp_octs:32;
+		uint64_t drp_pkts:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_stat10_x {
+	uint64_t u64;
+	struct cvmx_pip_stat10_x_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t bcast:32;
+		uint64_t mcast:32;
+#else
+		uint64_t mcast:32;
+		uint64_t bcast:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_stat10_prtx {
+	uint64_t u64;
+	struct cvmx_pip_stat10_prtx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t bcast:32;
+		uint64_t mcast:32;
+#else
+		uint64_t mcast:32;
+		uint64_t bcast:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_stat11_x {
+	uint64_t u64;
+	struct cvmx_pip_stat11_x_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t bcast:32;
+		uint64_t mcast:32;
+#else
+		uint64_t mcast:32;
+		uint64_t bcast:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_stat11_prtx {
+	uint64_t u64;
+	struct cvmx_pip_stat11_prtx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t bcast:32;
+		uint64_t mcast:32;
+#else
+		uint64_t mcast:32;
+		uint64_t bcast:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_stat1_x {
+	uint64_t u64;
+	struct cvmx_pip_stat1_x_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t octs:48;
+#else
+		uint64_t octs:48;
+		uint64_t reserved_48_63:16;
+#endif
+	} s;
+};
+
+union cvmx_pip_stat1_prtx {
+	uint64_t u64;
+	struct cvmx_pip_stat1_prtx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t octs:48;
+#else
+		uint64_t octs:48;
+		uint64_t reserved_48_63:16;
+#endif
+	} s;
+};
+
+union cvmx_pip_stat2_x {
+	uint64_t u64;
+	struct cvmx_pip_stat2_x_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t pkts:32;
+		uint64_t raw:32;
+#else
+		uint64_t raw:32;
+		uint64_t pkts:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_stat2_prtx {
+	uint64_t u64;
+	struct cvmx_pip_stat2_prtx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t pkts:32;
+		uint64_t raw:32;
+#else
+		uint64_t raw:32;
+		uint64_t pkts:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_stat3_x {
+	uint64_t u64;
+	struct cvmx_pip_stat3_x_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t bcst:32;
+		uint64_t mcst:32;
+#else
+		uint64_t mcst:32;
+		uint64_t bcst:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_stat3_prtx {
+	uint64_t u64;
+	struct cvmx_pip_stat3_prtx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t bcst:32;
+		uint64_t mcst:32;
+#else
+		uint64_t mcst:32;
+		uint64_t bcst:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_stat4_x {
+	uint64_t u64;
+	struct cvmx_pip_stat4_x_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t h65to127:32;
+		uint64_t h64:32;
+#else
+		uint64_t h64:32;
+		uint64_t h65to127:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_stat4_prtx {
+	uint64_t u64;
+	struct cvmx_pip_stat4_prtx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t h65to127:32;
+		uint64_t h64:32;
+#else
+		uint64_t h64:32;
+		uint64_t h65to127:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_stat5_x {
+	uint64_t u64;
+	struct cvmx_pip_stat5_x_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t h256to511:32;
+		uint64_t h128to255:32;
+#else
+		uint64_t h128to255:32;
+		uint64_t h256to511:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_stat5_prtx {
+	uint64_t u64;
+	struct cvmx_pip_stat5_prtx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t h256to511:32;
+		uint64_t h128to255:32;
+#else
+		uint64_t h128to255:32;
+		uint64_t h256to511:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_stat6_x {
+	uint64_t u64;
+	struct cvmx_pip_stat6_x_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t h1024to1518:32;
+		uint64_t h512to1023:32;
+#else
+		uint64_t h512to1023:32;
+		uint64_t h1024to1518:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_stat6_prtx {
+	uint64_t u64;
+	struct cvmx_pip_stat6_prtx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t h1024to1518:32;
+		uint64_t h512to1023:32;
+#else
+		uint64_t h512to1023:32;
+		uint64_t h1024to1518:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_stat7_x {
+	uint64_t u64;
+	struct cvmx_pip_stat7_x_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t fcs:32;
+		uint64_t h1519:32;
+#else
+		uint64_t h1519:32;
+		uint64_t fcs:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_stat7_prtx {
+	uint64_t u64;
+	struct cvmx_pip_stat7_prtx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t fcs:32;
+		uint64_t h1519:32;
+#else
+		uint64_t h1519:32;
+		uint64_t fcs:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_stat8_x {
+	uint64_t u64;
+	struct cvmx_pip_stat8_x_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t frag:32;
+		uint64_t undersz:32;
+#else
+		uint64_t undersz:32;
+		uint64_t frag:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_stat8_prtx {
+	uint64_t u64;
+	struct cvmx_pip_stat8_prtx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t frag:32;
+		uint64_t undersz:32;
+#else
+		uint64_t undersz:32;
+		uint64_t frag:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_stat9_x {
+	uint64_t u64;
+	struct cvmx_pip_stat9_x_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t jabber:32;
+		uint64_t oversz:32;
+#else
+		uint64_t oversz:32;
+		uint64_t jabber:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_stat9_prtx {
+	uint64_t u64;
+	struct cvmx_pip_stat9_prtx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t jabber:32;
+		uint64_t oversz:32;
+#else
+		uint64_t oversz:32;
+		uint64_t jabber:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_stat_ctl {
+	uint64_t u64;
+	struct cvmx_pip_stat_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_9_63:55;
+		uint64_t mode:1;
+		uint64_t reserved_1_7:7;
+		uint64_t rdclr:1;
+#else
+		uint64_t rdclr:1;
+		uint64_t reserved_1_7:7;
+		uint64_t mode:1;
+		uint64_t reserved_9_63:55;
+#endif
+	} s;
+	struct cvmx_pip_stat_ctl_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t rdclr:1;
+#else
+		uint64_t rdclr:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} cn30xx;
+};
+
+union cvmx_pip_stat_inb_errsx {
+	uint64_t u64;
+	struct cvmx_pip_stat_inb_errsx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t errs:16;
+#else
+		uint64_t errs:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_pip_stat_inb_errs_pkndx {
+	uint64_t u64;
+	struct cvmx_pip_stat_inb_errs_pkndx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t errs:16;
+#else
+		uint64_t errs:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_pip_stat_inb_octsx {
+	uint64_t u64;
+	struct cvmx_pip_stat_inb_octsx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t octs:48;
+#else
+		uint64_t octs:48;
+		uint64_t reserved_48_63:16;
+#endif
+	} s;
+};
+
+union cvmx_pip_stat_inb_octs_pkndx {
+	uint64_t u64;
+	struct cvmx_pip_stat_inb_octs_pkndx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t octs:48;
+#else
+		uint64_t octs:48;
+		uint64_t reserved_48_63:16;
+#endif
+	} s;
+};
+
+union cvmx_pip_stat_inb_pktsx {
+	uint64_t u64;
+	struct cvmx_pip_stat_inb_pktsx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t pkts:32;
+#else
+		uint64_t pkts:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_stat_inb_pkts_pkndx {
+	uint64_t u64;
+	struct cvmx_pip_stat_inb_pkts_pkndx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t pkts:32;
+#else
+		uint64_t pkts:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_sub_pkind_fcsx {
+	uint64_t u64;
+	struct cvmx_pip_sub_pkind_fcsx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t port_bit:64;
+#else
+		uint64_t port_bit:64;
+#endif
+	} s;
+};
+
+union cvmx_pip_tag_incx {
+	uint64_t u64;
+	struct cvmx_pip_tag_incx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t en:8;
+#else
+		uint64_t en:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_pip_tag_mask {
+	uint64_t u64;
+	struct cvmx_pip_tag_mask_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t mask:16;
+#else
+		uint64_t mask:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_pip_tag_secret {
+	uint64_t u64;
+	struct cvmx_pip_tag_secret_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t dst:16;
+		uint64_t src:16;
+#else
+		uint64_t src:16;
+		uint64_t dst:16;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_todo_entry {
+	uint64_t u64;
+	struct cvmx_pip_todo_entry_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t val:1;
+		uint64_t reserved_62_62:1;
+		uint64_t entry:62;
+#else
+		uint64_t entry:62;
+		uint64_t reserved_62_62:1;
+		uint64_t val:1;
+#endif
+	} s;
+};
+
+union cvmx_pip_vlan_etypesx {
+	uint64_t u64;
+	struct cvmx_pip_vlan_etypesx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t type3:16;
+		uint64_t type2:16;
+		uint64_t type1:16;
+		uint64_t type0:16;
+#else
+		uint64_t type0:16;
+		uint64_t type1:16;
+		uint64_t type2:16;
+		uint64_t type3:16;
+#endif
+	} s;
+};
+
+union cvmx_pip_xstat0_prtx {
+	uint64_t u64;
+	struct cvmx_pip_xstat0_prtx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t drp_pkts:32;
+		uint64_t drp_octs:32;
+#else
+		uint64_t drp_octs:32;
+		uint64_t drp_pkts:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_xstat10_prtx {
+	uint64_t u64;
+	struct cvmx_pip_xstat10_prtx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t bcast:32;
+		uint64_t mcast:32;
+#else
+		uint64_t mcast:32;
+		uint64_t bcast:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_xstat11_prtx {
+	uint64_t u64;
+	struct cvmx_pip_xstat11_prtx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t bcast:32;
+		uint64_t mcast:32;
+#else
+		uint64_t mcast:32;
+		uint64_t bcast:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_xstat1_prtx {
+	uint64_t u64;
+	struct cvmx_pip_xstat1_prtx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t octs:48;
+#else
+		uint64_t octs:48;
+		uint64_t reserved_48_63:16;
+#endif
+	} s;
+};
+
+union cvmx_pip_xstat2_prtx {
+	uint64_t u64;
+	struct cvmx_pip_xstat2_prtx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t pkts:32;
+		uint64_t raw:32;
+#else
+		uint64_t raw:32;
+		uint64_t pkts:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_xstat3_prtx {
+	uint64_t u64;
+	struct cvmx_pip_xstat3_prtx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t bcst:32;
+		uint64_t mcst:32;
+#else
+		uint64_t mcst:32;
+		uint64_t bcst:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_xstat4_prtx {
+	uint64_t u64;
+	struct cvmx_pip_xstat4_prtx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t h65to127:32;
+		uint64_t h64:32;
+#else
+		uint64_t h64:32;
+		uint64_t h65to127:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_xstat5_prtx {
+	uint64_t u64;
+	struct cvmx_pip_xstat5_prtx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t h256to511:32;
+		uint64_t h128to255:32;
+#else
+		uint64_t h128to255:32;
+		uint64_t h256to511:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_xstat6_prtx {
+	uint64_t u64;
+	struct cvmx_pip_xstat6_prtx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t h1024to1518:32;
+		uint64_t h512to1023:32;
+#else
+		uint64_t h512to1023:32;
+		uint64_t h1024to1518:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_xstat7_prtx {
+	uint64_t u64;
+	struct cvmx_pip_xstat7_prtx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t fcs:32;
+		uint64_t h1519:32;
+#else
+		uint64_t h1519:32;
+		uint64_t fcs:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_xstat8_prtx {
+	uint64_t u64;
+	struct cvmx_pip_xstat8_prtx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t frag:32;
+		uint64_t undersz:32;
+#else
+		uint64_t undersz:32;
+		uint64_t frag:32;
+#endif
+	} s;
+};
+
+union cvmx_pip_xstat9_prtx {
+	uint64_t u64;
+	struct cvmx_pip_xstat9_prtx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t jabber:32;
+		uint64_t oversz:32;
+#else
+		uint64_t oversz:32;
+		uint64_t jabber:32;
+#endif
+	} s;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-pip.h b/arch/mips/include/asm/octeon/cvmx-pip.h
new file mode 100644
index 000000000..01ca7267a
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-pip.h
@@ -0,0 +1,524 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ * Interface to the hardware Packet Input Processing unit.
+ *
+ */
+
+#ifndef __CVMX_PIP_H__
+#define __CVMX_PIP_H__
+
+#include <asm/octeon/cvmx-wqe.h>
+#include <asm/octeon/cvmx-fpa.h>
+#include <asm/octeon/cvmx-pip-defs.h>
+
+#define CVMX_PIP_NUM_INPUT_PORTS		48
+#define CVMX_PIP_NUM_WATCHERS			4
+
+/*
+ * Encodes the different error and exception codes
+ */
+typedef enum {
+	CVMX_PIP_L4_NO_ERR = 0ull,
+	/*
+	 * 1 = TCP (UDP) packet not long enough to cover TCP (UDP)
+	 * header
+	 */
+	CVMX_PIP_L4_MAL_ERR = 1ull,
+	/* 2  = TCP/UDP checksum failure */
+	CVMX_PIP_CHK_ERR = 2ull,
+	/*
+	 * 3 = TCP/UDP length check (TCP/UDP length does not match IP
+	 * length).
+	 */
+	CVMX_PIP_L4_LENGTH_ERR = 3ull,
+	/* 4  = illegal TCP/UDP port (either source or dest port is zero) */
+	CVMX_PIP_BAD_PRT_ERR = 4ull,
+	/* 8  = TCP flags = FIN only */
+	CVMX_PIP_TCP_FLG8_ERR = 8ull,
+	/* 9  = TCP flags = 0 */
+	CVMX_PIP_TCP_FLG9_ERR = 9ull,
+	/* 10 = TCP flags = FIN+RST+* */
+	CVMX_PIP_TCP_FLG10_ERR = 10ull,
+	/* 11 = TCP flags = SYN+URG+* */
+	CVMX_PIP_TCP_FLG11_ERR = 11ull,
+	/* 12 = TCP flags = SYN+RST+* */
+	CVMX_PIP_TCP_FLG12_ERR = 12ull,
+	/* 13 = TCP flags = SYN+FIN+* */
+	CVMX_PIP_TCP_FLG13_ERR = 13ull
+} cvmx_pip_l4_err_t;
+
+typedef enum {
+
+	CVMX_PIP_IP_NO_ERR = 0ull,
+	/* 1 = not IPv4 or IPv6 */
+	CVMX_PIP_NOT_IP = 1ull,
+	/* 2 = IPv4 header checksum violation */
+	CVMX_PIP_IPV4_HDR_CHK = 2ull,
+	/* 3 = malformed (packet not long enough to cover IP hdr) */
+	CVMX_PIP_IP_MAL_HDR = 3ull,
+	/* 4 = malformed (packet not long enough to cover len in IP hdr) */
+	CVMX_PIP_IP_MAL_PKT = 4ull,
+	/* 5 = TTL / hop count equal zero */
+	CVMX_PIP_TTL_HOP = 5ull,
+	/* 6 = IPv4 options / IPv6 early extension headers */
+	CVMX_PIP_OPTS = 6ull
+} cvmx_pip_ip_exc_t;
+
+/**
+ * NOTES
+ *	 late collision (data received before collision)
+ *	      late collisions cannot be detected by the receiver
+ *	      they would appear as JAM bits which would appear as bad FCS
+ *	      or carrier extend error which is CVMX_PIP_EXTEND_ERR
+ */
+typedef enum {
+	/* No error */
+	CVMX_PIP_RX_NO_ERR = 0ull,
+	/* RGM+SPI 1 = partially received packet (buffering/bandwidth
+	 * not adequate) */
+	CVMX_PIP_PARTIAL_ERR = 1ull,
+	/* RGM+SPI 2 = receive packet too large and truncated */
+	CVMX_PIP_JABBER_ERR = 2ull,
+	/*
+	 * RGM 3 = max frame error (pkt len > max frame len) (with FCS
+	 * error)
+	 */
+	CVMX_PIP_OVER_FCS_ERR = 3ull,
+	/* RGM+SPI 4 = max frame error (pkt len > max frame len) */
+	CVMX_PIP_OVER_ERR = 4ull,
+	/*
+	 * RGM 5 = nibble error (data not byte multiple - 100M and 10M
+	 * only)
+	 */
+	CVMX_PIP_ALIGN_ERR = 5ull,
+	/*
+	 * RGM 6 = min frame error (pkt len < min frame len) (with FCS
+	 * error)
+	 */
+	CVMX_PIP_UNDER_FCS_ERR = 6ull,
+	/* RGM	   7 = FCS error */
+	CVMX_PIP_GMX_FCS_ERR = 7ull,
+	/* RGM+SPI 8 = min frame error (pkt len < min frame len) */
+	CVMX_PIP_UNDER_ERR = 8ull,
+	/* RGM	   9 = Frame carrier extend error */
+	CVMX_PIP_EXTEND_ERR = 9ull,
+	/*
+	 * RGM 10 = length mismatch (len did not match len in L2
+	 * length/type)
+	 */
+	CVMX_PIP_LENGTH_ERR = 10ull,
+	/* RGM 11 = Frame error (some or all data bits marked err) */
+	CVMX_PIP_DAT_ERR = 11ull,
+	/*     SPI 11 = DIP4 error */
+	CVMX_PIP_DIP_ERR = 11ull,
+	/*
+	 * RGM 12 = packet was not large enough to pass the skipper -
+	 * no inspection could occur.
+	 */
+	CVMX_PIP_SKIP_ERR = 12ull,
+	/*
+	 * RGM 13 = studder error (data not repeated - 100M and 10M
+	 * only)
+	 */
+	CVMX_PIP_NIBBLE_ERR = 13ull,
+	/* RGM+SPI 16 = FCS error */
+	CVMX_PIP_PIP_FCS = 16L,
+	/*
+	 * RGM+SPI+PCI 17 = packet was not large enough to pass the
+	 * skipper - no inspection could occur.
+	 */
+	CVMX_PIP_PIP_SKIP_ERR = 17L,
+	/*
+	 * RGM+SPI+PCI 18 = malformed l2 (packet not long enough to
+	 * cover L2 hdr).
+	 */
+	CVMX_PIP_PIP_L2_MAL_HDR = 18L
+	/*
+	 * NOTES: xx = late collision (data received before collision)
+	 *	 late collisions cannot be detected by the receiver
+	 *	 they would appear as JAM bits which would appear as
+	 *	 bad FCS or carrier extend error which is
+	 *	 CVMX_PIP_EXTEND_ERR
+	 */
+} cvmx_pip_rcv_err_t;
+
+/**
+ * This defines the err_code field errors in the work Q entry
+ */
+typedef union {
+	cvmx_pip_l4_err_t l4_err;
+	cvmx_pip_ip_exc_t ip_exc;
+	cvmx_pip_rcv_err_t rcv_err;
+} cvmx_pip_err_t;
+
+/**
+ * Status statistics for a port
+ */
+typedef struct {
+	/* Inbound octets marked to be dropped by the IPD */
+	uint32_t dropped_octets;
+	/* Inbound packets marked to be dropped by the IPD */
+	uint32_t dropped_packets;
+	/* RAW PCI Packets received by PIP per port */
+	uint32_t pci_raw_packets;
+	/* Number of octets processed by PIP */
+	uint32_t octets;
+	/* Number of packets processed by PIP */
+	uint32_t packets;
+	/*
+	 * Number of identified L2 multicast packets.	Does not
+	 * include broadcast packets.  Only includes packets whose
+	 * parse mode is SKIP_TO_L2
+	 */
+	uint32_t multicast_packets;
+	/*
+	 * Number of identified L2 broadcast packets.	Does not
+	 * include multicast packets.  Only includes packets whose
+	 * parse mode is SKIP_TO_L2
+	 */
+	uint32_t broadcast_packets;
+	/* Number of 64B packets */
+	uint32_t len_64_packets;
+	/* Number of 65-127B packets */
+	uint32_t len_65_127_packets;
+	/* Number of 128-255B packets */
+	uint32_t len_128_255_packets;
+	/* Number of 256-511B packets */
+	uint32_t len_256_511_packets;
+	/* Number of 512-1023B packets */
+	uint32_t len_512_1023_packets;
+	/* Number of 1024-1518B packets */
+	uint32_t len_1024_1518_packets;
+	/* Number of 1519-max packets */
+	uint32_t len_1519_max_packets;
+	/* Number of packets with FCS or Align opcode errors */
+	uint32_t fcs_align_err_packets;
+	/* Number of packets with length < min */
+	uint32_t runt_packets;
+	/* Number of packets with length < min and FCS error */
+	uint32_t runt_crc_packets;
+	/* Number of packets with length > max */
+	uint32_t oversize_packets;
+	/* Number of packets with length > max and FCS error */
+	uint32_t oversize_crc_packets;
+	/* Number of packets without GMX/SPX/PCI errors received by PIP */
+	uint32_t inb_packets;
+	/*
+	 * Total number of octets from all packets received by PIP,
+	 * including CRC
+	 */
+	uint64_t inb_octets;
+	/* Number of packets with GMX/SPX/PCI errors received by PIP */
+	uint16_t inb_errors;
+} cvmx_pip_port_status_t;
+
+/**
+ * Definition of the PIP custom header that can be prepended
+ * to a packet by external hardware.
+ */
+typedef union {
+	uint64_t u64;
+	struct {
+		/*
+		 * Documented as R - Set if the Packet is RAWFULL. If
+		 * set, this header must be the full 8 bytes.
+		 */
+		uint64_t rawfull:1;
+		/* Must be zero */
+		uint64_t reserved0:5;
+		/* PIP parse mode for this packet */
+		uint64_t parse_mode:2;
+		/* Must be zero */
+		uint64_t reserved1:1;
+		/*
+		 * Skip amount, including this header, to the
+		 * beginning of the packet
+		 */
+		uint64_t skip_len:7;
+		/* Must be zero */
+		uint64_t reserved2:6;
+		/* POW input queue for this packet */
+		uint64_t qos:3;
+		/* POW input group for this packet */
+		uint64_t grp:4;
+		/*
+		 * Flag to store this packet in the work queue entry,
+		 * if possible
+		 */
+		uint64_t rs:1;
+		/* POW input tag type */
+		uint64_t tag_type:2;
+		/* POW input tag */
+		uint64_t tag:32;
+	} s;
+} cvmx_pip_pkt_inst_hdr_t;
+
+/* CSR typedefs have been moved to cvmx-csr-*.h */
+
+/**
+ * Configure an ethernet input port
+ *
+ * @port_num: Port number to configure
+ * @port_cfg: Port hardware configuration
+ * @port_tag_cfg:
+ *		   Port POW tagging configuration
+ */
+static inline void cvmx_pip_config_port(uint64_t port_num,
+					union cvmx_pip_prt_cfgx port_cfg,
+					union cvmx_pip_prt_tagx port_tag_cfg)
+{
+	cvmx_write_csr(CVMX_PIP_PRT_CFGX(port_num), port_cfg.u64);
+	cvmx_write_csr(CVMX_PIP_PRT_TAGX(port_num), port_tag_cfg.u64);
+}
+#if 0
+/**
+ * @deprecated	    This function is a thin wrapper around the Pass1 version
+ *		    of the CVMX_PIP_QOS_WATCHX CSR; Pass2 has added a field for
+ *		    setting the group that is incompatible with this function,
+ *		    the preferred upgrade path is to use the CSR directly.
+ *
+ * Configure the global QoS packet watchers. Each watcher is
+ * capable of matching a field in a packet to determine the
+ * QoS queue for scheduling.
+ *
+ * @watcher:	Watcher number to configure (0 - 3).
+ * @match_type: Watcher match type
+ * @match_value:
+ *		     Value the watcher will match against
+ * @qos:	QoS queue for packets matching this watcher
+ */
+static inline void cvmx_pip_config_watcher(uint64_t watcher,
+					   cvmx_pip_qos_watch_types match_type,
+					   uint64_t match_value, uint64_t qos)
+{
+	cvmx_pip_port_watcher_cfg_t watcher_config;
+
+	watcher_config.u64 = 0;
+	watcher_config.s.match_type = match_type;
+	watcher_config.s.match_value = match_value;
+	watcher_config.s.qos = qos;
+
+	cvmx_write_csr(CVMX_PIP_QOS_WATCHX(watcher), watcher_config.u64);
+}
+#endif
+/**
+ * Configure the VLAN priority to QoS queue mapping.
+ *
+ * @vlan_priority:
+ *		 VLAN priority (0-7)
+ * @qos:    QoS queue for packets matching this watcher
+ */
+static inline void cvmx_pip_config_vlan_qos(uint64_t vlan_priority,
+					    uint64_t qos)
+{
+	union cvmx_pip_qos_vlanx pip_qos_vlanx;
+	pip_qos_vlanx.u64 = 0;
+	pip_qos_vlanx.s.qos = qos;
+	cvmx_write_csr(CVMX_PIP_QOS_VLANX(vlan_priority), pip_qos_vlanx.u64);
+}
+
+/**
+ * Configure the Diffserv to QoS queue mapping.
+ *
+ * @diffserv: Diffserv field value (0-63)
+ * @qos:      QoS queue for packets matching this watcher
+ */
+static inline void cvmx_pip_config_diffserv_qos(uint64_t diffserv, uint64_t qos)
+{
+	union cvmx_pip_qos_diffx pip_qos_diffx;
+	pip_qos_diffx.u64 = 0;
+	pip_qos_diffx.s.qos = qos;
+	cvmx_write_csr(CVMX_PIP_QOS_DIFFX(diffserv), pip_qos_diffx.u64);
+}
+
+/**
+ * Get the status counters for a port.
+ *
+ * @port_num: Port number to get statistics for.
+ * @clear:    Set to 1 to clear the counters after they are read
+ * @status:   Where to put the results.
+ */
+static inline void cvmx_pip_get_port_status(uint64_t port_num, uint64_t clear,
+					    cvmx_pip_port_status_t *status)
+{
+	union cvmx_pip_stat_ctl pip_stat_ctl;
+	union cvmx_pip_stat0_prtx stat0;
+	union cvmx_pip_stat1_prtx stat1;
+	union cvmx_pip_stat2_prtx stat2;
+	union cvmx_pip_stat3_prtx stat3;
+	union cvmx_pip_stat4_prtx stat4;
+	union cvmx_pip_stat5_prtx stat5;
+	union cvmx_pip_stat6_prtx stat6;
+	union cvmx_pip_stat7_prtx stat7;
+	union cvmx_pip_stat8_prtx stat8;
+	union cvmx_pip_stat9_prtx stat9;
+	union cvmx_pip_stat_inb_pktsx pip_stat_inb_pktsx;
+	union cvmx_pip_stat_inb_octsx pip_stat_inb_octsx;
+	union cvmx_pip_stat_inb_errsx pip_stat_inb_errsx;
+
+	pip_stat_ctl.u64 = 0;
+	pip_stat_ctl.s.rdclr = clear;
+	cvmx_write_csr(CVMX_PIP_STAT_CTL, pip_stat_ctl.u64);
+
+	stat0.u64 = cvmx_read_csr(CVMX_PIP_STAT0_PRTX(port_num));
+	stat1.u64 = cvmx_read_csr(CVMX_PIP_STAT1_PRTX(port_num));
+	stat2.u64 = cvmx_read_csr(CVMX_PIP_STAT2_PRTX(port_num));
+	stat3.u64 = cvmx_read_csr(CVMX_PIP_STAT3_PRTX(port_num));
+	stat4.u64 = cvmx_read_csr(CVMX_PIP_STAT4_PRTX(port_num));
+	stat5.u64 = cvmx_read_csr(CVMX_PIP_STAT5_PRTX(port_num));
+	stat6.u64 = cvmx_read_csr(CVMX_PIP_STAT6_PRTX(port_num));
+	stat7.u64 = cvmx_read_csr(CVMX_PIP_STAT7_PRTX(port_num));
+	stat8.u64 = cvmx_read_csr(CVMX_PIP_STAT8_PRTX(port_num));
+	stat9.u64 = cvmx_read_csr(CVMX_PIP_STAT9_PRTX(port_num));
+	pip_stat_inb_pktsx.u64 =
+	    cvmx_read_csr(CVMX_PIP_STAT_INB_PKTSX(port_num));
+	pip_stat_inb_octsx.u64 =
+	    cvmx_read_csr(CVMX_PIP_STAT_INB_OCTSX(port_num));
+	pip_stat_inb_errsx.u64 =
+	    cvmx_read_csr(CVMX_PIP_STAT_INB_ERRSX(port_num));
+
+	status->dropped_octets = stat0.s.drp_octs;
+	status->dropped_packets = stat0.s.drp_pkts;
+	status->octets = stat1.s.octs;
+	status->pci_raw_packets = stat2.s.raw;
+	status->packets = stat2.s.pkts;
+	status->multicast_packets = stat3.s.mcst;
+	status->broadcast_packets = stat3.s.bcst;
+	status->len_64_packets = stat4.s.h64;
+	status->len_65_127_packets = stat4.s.h65to127;
+	status->len_128_255_packets = stat5.s.h128to255;
+	status->len_256_511_packets = stat5.s.h256to511;
+	status->len_512_1023_packets = stat6.s.h512to1023;
+	status->len_1024_1518_packets = stat6.s.h1024to1518;
+	status->len_1519_max_packets = stat7.s.h1519;
+	status->fcs_align_err_packets = stat7.s.fcs;
+	status->runt_packets = stat8.s.undersz;
+	status->runt_crc_packets = stat8.s.frag;
+	status->oversize_packets = stat9.s.oversz;
+	status->oversize_crc_packets = stat9.s.jabber;
+	status->inb_packets = pip_stat_inb_pktsx.s.pkts;
+	status->inb_octets = pip_stat_inb_octsx.s.octs;
+	status->inb_errors = pip_stat_inb_errsx.s.errs;
+
+	if (cvmx_octeon_is_pass1()) {
+		/*
+		 * Kludge to fix Octeon Pass 1 errata - Drop counts
+		 * don't work.
+		 */
+		if (status->inb_packets > status->packets)
+			status->dropped_packets =
+			    status->inb_packets - status->packets;
+		else
+			status->dropped_packets = 0;
+		if (status->inb_octets - status->inb_packets * 4 >
+		    status->octets)
+			status->dropped_octets =
+			    status->inb_octets - status->inb_packets * 4 -
+			    status->octets;
+		else
+			status->dropped_octets = 0;
+	}
+}
+
+/**
+ * Configure the hardware CRC engine
+ *
+ * @interface: Interface to configure (0 or 1)
+ * @invert_result:
+ *		   Invert the result of the CRC
+ * @reflect:  Reflect
+ * @initialization_vector:
+ *		   CRC initialization vector
+ */
+static inline void cvmx_pip_config_crc(uint64_t interface,
+				       uint64_t invert_result, uint64_t reflect,
+				       uint32_t initialization_vector)
+{
+	if (OCTEON_IS_MODEL(OCTEON_CN38XX) || OCTEON_IS_MODEL(OCTEON_CN58XX)) {
+		union cvmx_pip_crc_ctlx config;
+		union cvmx_pip_crc_ivx pip_crc_ivx;
+
+		config.u64 = 0;
+		config.s.invres = invert_result;
+		config.s.reflect = reflect;
+		cvmx_write_csr(CVMX_PIP_CRC_CTLX(interface), config.u64);
+
+		pip_crc_ivx.u64 = 0;
+		pip_crc_ivx.s.iv = initialization_vector;
+		cvmx_write_csr(CVMX_PIP_CRC_IVX(interface), pip_crc_ivx.u64);
+	}
+}
+
+/**
+ * Clear all bits in a tag mask. This should be called on
+ * startup before any calls to cvmx_pip_tag_mask_set. Each bit
+ * set in the final mask represent a byte used in the packet for
+ * tag generation.
+ *
+ * @mask_index: Which tag mask to clear (0..3)
+ */
+static inline void cvmx_pip_tag_mask_clear(uint64_t mask_index)
+{
+	uint64_t index;
+	union cvmx_pip_tag_incx pip_tag_incx;
+	pip_tag_incx.u64 = 0;
+	pip_tag_incx.s.en = 0;
+	for (index = mask_index * 16; index < (mask_index + 1) * 16; index++)
+		cvmx_write_csr(CVMX_PIP_TAG_INCX(index), pip_tag_incx.u64);
+}
+
+/**
+ * Sets a range of bits in the tag mask. The tag mask is used
+ * when the cvmx_pip_port_tag_cfg_t tag_mode is non zero.
+ * There are four separate masks that can be configured.
+ *
+ * @mask_index: Which tag mask to modify (0..3)
+ * @offset: Offset into the bitmask to set bits at. Use the GCC macro
+ *	    offsetof() to determine the offsets into packet headers.
+ *	    For example, offsetof(ethhdr, protocol) returns the offset
+ *	    of the ethernet protocol field.  The bitmask selects which
+ *	    bytes to include the tag, with bit offset X selecting
+ *	    byte at offset X from the beginning of the packet data.
+ * @len:    Number of bytes to include. Usually this is the sizeof()
+ *	    the field.
+ */
+static inline void cvmx_pip_tag_mask_set(uint64_t mask_index, uint64_t offset,
+					 uint64_t len)
+{
+	while (len--) {
+		union cvmx_pip_tag_incx pip_tag_incx;
+		uint64_t index = mask_index * 16 + offset / 8;
+		pip_tag_incx.u64 = cvmx_read_csr(CVMX_PIP_TAG_INCX(index));
+		pip_tag_incx.s.en |= 0x80 >> (offset & 0x7);
+		cvmx_write_csr(CVMX_PIP_TAG_INCX(index), pip_tag_incx.u64);
+		offset++;
+	}
+}
+
+#endif /*  __CVMX_PIP_H__ */
diff --git a/arch/mips/include/asm/octeon/cvmx-pko-defs.h b/arch/mips/include/asm/octeon/cvmx-pko-defs.h
new file mode 100644
index 000000000..7e14c0d32
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-pko-defs.h
@@ -0,0 +1,2205 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2012 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_PKO_DEFS_H__
+#define __CVMX_PKO_DEFS_H__
+
+#define CVMX_PKO_MEM_COUNT0 (CVMX_ADD_IO_SEG(0x0001180050001080ull))
+#define CVMX_PKO_MEM_COUNT1 (CVMX_ADD_IO_SEG(0x0001180050001088ull))
+#define CVMX_PKO_MEM_DEBUG0 (CVMX_ADD_IO_SEG(0x0001180050001100ull))
+#define CVMX_PKO_MEM_DEBUG1 (CVMX_ADD_IO_SEG(0x0001180050001108ull))
+#define CVMX_PKO_MEM_DEBUG10 (CVMX_ADD_IO_SEG(0x0001180050001150ull))
+#define CVMX_PKO_MEM_DEBUG11 (CVMX_ADD_IO_SEG(0x0001180050001158ull))
+#define CVMX_PKO_MEM_DEBUG12 (CVMX_ADD_IO_SEG(0x0001180050001160ull))
+#define CVMX_PKO_MEM_DEBUG13 (CVMX_ADD_IO_SEG(0x0001180050001168ull))
+#define CVMX_PKO_MEM_DEBUG14 (CVMX_ADD_IO_SEG(0x0001180050001170ull))
+#define CVMX_PKO_MEM_DEBUG2 (CVMX_ADD_IO_SEG(0x0001180050001110ull))
+#define CVMX_PKO_MEM_DEBUG3 (CVMX_ADD_IO_SEG(0x0001180050001118ull))
+#define CVMX_PKO_MEM_DEBUG4 (CVMX_ADD_IO_SEG(0x0001180050001120ull))
+#define CVMX_PKO_MEM_DEBUG5 (CVMX_ADD_IO_SEG(0x0001180050001128ull))
+#define CVMX_PKO_MEM_DEBUG6 (CVMX_ADD_IO_SEG(0x0001180050001130ull))
+#define CVMX_PKO_MEM_DEBUG7 (CVMX_ADD_IO_SEG(0x0001180050001138ull))
+#define CVMX_PKO_MEM_DEBUG8 (CVMX_ADD_IO_SEG(0x0001180050001140ull))
+#define CVMX_PKO_MEM_DEBUG9 (CVMX_ADD_IO_SEG(0x0001180050001148ull))
+#define CVMX_PKO_MEM_IPORT_PTRS (CVMX_ADD_IO_SEG(0x0001180050001030ull))
+#define CVMX_PKO_MEM_IPORT_QOS (CVMX_ADD_IO_SEG(0x0001180050001038ull))
+#define CVMX_PKO_MEM_IQUEUE_PTRS (CVMX_ADD_IO_SEG(0x0001180050001040ull))
+#define CVMX_PKO_MEM_IQUEUE_QOS (CVMX_ADD_IO_SEG(0x0001180050001048ull))
+#define CVMX_PKO_MEM_PORT_PTRS (CVMX_ADD_IO_SEG(0x0001180050001010ull))
+#define CVMX_PKO_MEM_PORT_QOS (CVMX_ADD_IO_SEG(0x0001180050001018ull))
+#define CVMX_PKO_MEM_PORT_RATE0 (CVMX_ADD_IO_SEG(0x0001180050001020ull))
+#define CVMX_PKO_MEM_PORT_RATE1 (CVMX_ADD_IO_SEG(0x0001180050001028ull))
+#define CVMX_PKO_MEM_QUEUE_PTRS (CVMX_ADD_IO_SEG(0x0001180050001000ull))
+#define CVMX_PKO_MEM_QUEUE_QOS (CVMX_ADD_IO_SEG(0x0001180050001008ull))
+#define CVMX_PKO_MEM_THROTTLE_INT (CVMX_ADD_IO_SEG(0x0001180050001058ull))
+#define CVMX_PKO_MEM_THROTTLE_PIPE (CVMX_ADD_IO_SEG(0x0001180050001050ull))
+#define CVMX_PKO_REG_BIST_RESULT (CVMX_ADD_IO_SEG(0x0001180050000080ull))
+#define CVMX_PKO_REG_CMD_BUF (CVMX_ADD_IO_SEG(0x0001180050000010ull))
+#define CVMX_PKO_REG_CRC_CTLX(offset) (CVMX_ADD_IO_SEG(0x0001180050000028ull) + ((offset) & 1) * 8)
+#define CVMX_PKO_REG_CRC_ENABLE (CVMX_ADD_IO_SEG(0x0001180050000020ull))
+#define CVMX_PKO_REG_CRC_IVX(offset) (CVMX_ADD_IO_SEG(0x0001180050000038ull) + ((offset) & 1) * 8)
+#define CVMX_PKO_REG_DEBUG0 (CVMX_ADD_IO_SEG(0x0001180050000098ull))
+#define CVMX_PKO_REG_DEBUG1 (CVMX_ADD_IO_SEG(0x00011800500000A0ull))
+#define CVMX_PKO_REG_DEBUG2 (CVMX_ADD_IO_SEG(0x00011800500000A8ull))
+#define CVMX_PKO_REG_DEBUG3 (CVMX_ADD_IO_SEG(0x00011800500000B0ull))
+#define CVMX_PKO_REG_DEBUG4 (CVMX_ADD_IO_SEG(0x00011800500000B8ull))
+#define CVMX_PKO_REG_ENGINE_INFLIGHT (CVMX_ADD_IO_SEG(0x0001180050000050ull))
+#define CVMX_PKO_REG_ENGINE_INFLIGHT1 (CVMX_ADD_IO_SEG(0x0001180050000318ull))
+#define CVMX_PKO_REG_ENGINE_STORAGEX(offset) (CVMX_ADD_IO_SEG(0x0001180050000300ull) + ((offset) & 1) * 8)
+#define CVMX_PKO_REG_ENGINE_THRESH (CVMX_ADD_IO_SEG(0x0001180050000058ull))
+#define CVMX_PKO_REG_ERROR (CVMX_ADD_IO_SEG(0x0001180050000088ull))
+#define CVMX_PKO_REG_FLAGS (CVMX_ADD_IO_SEG(0x0001180050000000ull))
+#define CVMX_PKO_REG_GMX_PORT_MODE (CVMX_ADD_IO_SEG(0x0001180050000018ull))
+#define CVMX_PKO_REG_INT_MASK (CVMX_ADD_IO_SEG(0x0001180050000090ull))
+#define CVMX_PKO_REG_LOOPBACK_BPID (CVMX_ADD_IO_SEG(0x0001180050000118ull))
+#define CVMX_PKO_REG_LOOPBACK_PKIND (CVMX_ADD_IO_SEG(0x0001180050000068ull))
+#define CVMX_PKO_REG_MIN_PKT (CVMX_ADD_IO_SEG(0x0001180050000070ull))
+#define CVMX_PKO_REG_PREEMPT (CVMX_ADD_IO_SEG(0x0001180050000110ull))
+#define CVMX_PKO_REG_QUEUE_MODE (CVMX_ADD_IO_SEG(0x0001180050000048ull))
+#define CVMX_PKO_REG_QUEUE_PREEMPT (CVMX_ADD_IO_SEG(0x0001180050000108ull))
+#define CVMX_PKO_REG_QUEUE_PTRS1 (CVMX_ADD_IO_SEG(0x0001180050000100ull))
+#define CVMX_PKO_REG_READ_IDX (CVMX_ADD_IO_SEG(0x0001180050000008ull))
+#define CVMX_PKO_REG_THROTTLE (CVMX_ADD_IO_SEG(0x0001180050000078ull))
+#define CVMX_PKO_REG_TIMESTAMP (CVMX_ADD_IO_SEG(0x0001180050000060ull))
+
+union cvmx_pko_mem_count0 {
+	uint64_t u64;
+	struct cvmx_pko_mem_count0_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t count:32;
+#else
+		uint64_t count:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_pko_mem_count1 {
+	uint64_t u64;
+	struct cvmx_pko_mem_count1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t count:48;
+#else
+		uint64_t count:48;
+		uint64_t reserved_48_63:16;
+#endif
+	} s;
+};
+
+union cvmx_pko_mem_debug0 {
+	uint64_t u64;
+	struct cvmx_pko_mem_debug0_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t fau:28;
+		uint64_t cmd:14;
+		uint64_t segs:6;
+		uint64_t size:16;
+#else
+		uint64_t size:16;
+		uint64_t segs:6;
+		uint64_t cmd:14;
+		uint64_t fau:28;
+#endif
+	} s;
+};
+
+union cvmx_pko_mem_debug1 {
+	uint64_t u64;
+	struct cvmx_pko_mem_debug1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t i:1;
+		uint64_t back:4;
+		uint64_t pool:3;
+		uint64_t size:16;
+		uint64_t ptr:40;
+#else
+		uint64_t ptr:40;
+		uint64_t size:16;
+		uint64_t pool:3;
+		uint64_t back:4;
+		uint64_t i:1;
+#endif
+	} s;
+};
+
+union cvmx_pko_mem_debug10 {
+	uint64_t u64;
+	struct cvmx_pko_mem_debug10_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_0_63:64;
+#else
+		uint64_t reserved_0_63:64;
+#endif
+	} s;
+	struct cvmx_pko_mem_debug10_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t fau:28;
+		uint64_t cmd:14;
+		uint64_t segs:6;
+		uint64_t size:16;
+#else
+		uint64_t size:16;
+		uint64_t segs:6;
+		uint64_t cmd:14;
+		uint64_t fau:28;
+#endif
+	} cn30xx;
+	struct cvmx_pko_mem_debug10_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_49_63:15;
+		uint64_t ptrs1:17;
+		uint64_t reserved_17_31:15;
+		uint64_t ptrs2:17;
+#else
+		uint64_t ptrs2:17;
+		uint64_t reserved_17_31:15;
+		uint64_t ptrs1:17;
+		uint64_t reserved_49_63:15;
+#endif
+	} cn50xx;
+};
+
+union cvmx_pko_mem_debug11 {
+	uint64_t u64;
+	struct cvmx_pko_mem_debug11_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t i:1;
+		uint64_t back:4;
+		uint64_t pool:3;
+		uint64_t size:16;
+		uint64_t reserved_0_39:40;
+#else
+		uint64_t reserved_0_39:40;
+		uint64_t size:16;
+		uint64_t pool:3;
+		uint64_t back:4;
+		uint64_t i:1;
+#endif
+	} s;
+	struct cvmx_pko_mem_debug11_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t i:1;
+		uint64_t back:4;
+		uint64_t pool:3;
+		uint64_t size:16;
+		uint64_t ptr:40;
+#else
+		uint64_t ptr:40;
+		uint64_t size:16;
+		uint64_t pool:3;
+		uint64_t back:4;
+		uint64_t i:1;
+#endif
+	} cn30xx;
+	struct cvmx_pko_mem_debug11_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_23_63:41;
+		uint64_t maj:1;
+		uint64_t uid:3;
+		uint64_t sop:1;
+		uint64_t len:1;
+		uint64_t chk:1;
+		uint64_t cnt:13;
+		uint64_t mod:3;
+#else
+		uint64_t mod:3;
+		uint64_t cnt:13;
+		uint64_t chk:1;
+		uint64_t len:1;
+		uint64_t sop:1;
+		uint64_t uid:3;
+		uint64_t maj:1;
+		uint64_t reserved_23_63:41;
+#endif
+	} cn50xx;
+};
+
+union cvmx_pko_mem_debug12 {
+	uint64_t u64;
+	struct cvmx_pko_mem_debug12_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_0_63:64;
+#else
+		uint64_t reserved_0_63:64;
+#endif
+	} s;
+	struct cvmx_pko_mem_debug12_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t data:64;
+#else
+		uint64_t data:64;
+#endif
+	} cn30xx;
+	struct cvmx_pko_mem_debug12_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t fau:28;
+		uint64_t cmd:14;
+		uint64_t segs:6;
+		uint64_t size:16;
+#else
+		uint64_t size:16;
+		uint64_t segs:6;
+		uint64_t cmd:14;
+		uint64_t fau:28;
+#endif
+	} cn50xx;
+	struct cvmx_pko_mem_debug12_cn68xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t state:64;
+#else
+		uint64_t state:64;
+#endif
+	} cn68xx;
+};
+
+union cvmx_pko_mem_debug13 {
+	uint64_t u64;
+	struct cvmx_pko_mem_debug13_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_0_63:64;
+#else
+		uint64_t reserved_0_63:64;
+#endif
+	} s;
+	struct cvmx_pko_mem_debug13_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_51_63:13;
+		uint64_t widx:17;
+		uint64_t ridx2:17;
+		uint64_t widx2:17;
+#else
+		uint64_t widx2:17;
+		uint64_t ridx2:17;
+		uint64_t widx:17;
+		uint64_t reserved_51_63:13;
+#endif
+	} cn30xx;
+	struct cvmx_pko_mem_debug13_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t i:1;
+		uint64_t back:4;
+		uint64_t pool:3;
+		uint64_t size:16;
+		uint64_t ptr:40;
+#else
+		uint64_t ptr:40;
+		uint64_t size:16;
+		uint64_t pool:3;
+		uint64_t back:4;
+		uint64_t i:1;
+#endif
+	} cn50xx;
+	struct cvmx_pko_mem_debug13_cn68xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t state:64;
+#else
+		uint64_t state:64;
+#endif
+	} cn68xx;
+};
+
+union cvmx_pko_mem_debug14 {
+	uint64_t u64;
+	struct cvmx_pko_mem_debug14_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_0_63:64;
+#else
+		uint64_t reserved_0_63:64;
+#endif
+	} s;
+	struct cvmx_pko_mem_debug14_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_17_63:47;
+		uint64_t ridx:17;
+#else
+		uint64_t ridx:17;
+		uint64_t reserved_17_63:47;
+#endif
+	} cn30xx;
+	struct cvmx_pko_mem_debug14_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t data:64;
+#else
+		uint64_t data:64;
+#endif
+	} cn52xx;
+};
+
+union cvmx_pko_mem_debug2 {
+	uint64_t u64;
+	struct cvmx_pko_mem_debug2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t i:1;
+		uint64_t back:4;
+		uint64_t pool:3;
+		uint64_t size:16;
+		uint64_t ptr:40;
+#else
+		uint64_t ptr:40;
+		uint64_t size:16;
+		uint64_t pool:3;
+		uint64_t back:4;
+		uint64_t i:1;
+#endif
+	} s;
+};
+
+union cvmx_pko_mem_debug3 {
+	uint64_t u64;
+	struct cvmx_pko_mem_debug3_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_0_63:64;
+#else
+		uint64_t reserved_0_63:64;
+#endif
+	} s;
+	struct cvmx_pko_mem_debug3_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t i:1;
+		uint64_t back:4;
+		uint64_t pool:3;
+		uint64_t size:16;
+		uint64_t ptr:40;
+#else
+		uint64_t ptr:40;
+		uint64_t size:16;
+		uint64_t pool:3;
+		uint64_t back:4;
+		uint64_t i:1;
+#endif
+	} cn30xx;
+	struct cvmx_pko_mem_debug3_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t data:64;
+#else
+		uint64_t data:64;
+#endif
+	} cn50xx;
+};
+
+union cvmx_pko_mem_debug4 {
+	uint64_t u64;
+	struct cvmx_pko_mem_debug4_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_0_63:64;
+#else
+		uint64_t reserved_0_63:64;
+#endif
+	} s;
+	struct cvmx_pko_mem_debug4_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t data:64;
+#else
+		uint64_t data:64;
+#endif
+	} cn30xx;
+	struct cvmx_pko_mem_debug4_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t cmnd_segs:3;
+		uint64_t cmnd_siz:16;
+		uint64_t cmnd_off:6;
+		uint64_t uid:3;
+		uint64_t dread_sop:1;
+		uint64_t init_dwrite:1;
+		uint64_t chk_once:1;
+		uint64_t chk_mode:1;
+		uint64_t active:1;
+		uint64_t static_p:1;
+		uint64_t qos:3;
+		uint64_t qcb_ridx:5;
+		uint64_t qid_off_max:4;
+		uint64_t qid_off:4;
+		uint64_t qid_base:8;
+		uint64_t wait:1;
+		uint64_t minor:2;
+		uint64_t major:3;
+#else
+		uint64_t major:3;
+		uint64_t minor:2;
+		uint64_t wait:1;
+		uint64_t qid_base:8;
+		uint64_t qid_off:4;
+		uint64_t qid_off_max:4;
+		uint64_t qcb_ridx:5;
+		uint64_t qos:3;
+		uint64_t static_p:1;
+		uint64_t active:1;
+		uint64_t chk_mode:1;
+		uint64_t chk_once:1;
+		uint64_t init_dwrite:1;
+		uint64_t dread_sop:1;
+		uint64_t uid:3;
+		uint64_t cmnd_off:6;
+		uint64_t cmnd_siz:16;
+		uint64_t cmnd_segs:3;
+#endif
+	} cn50xx;
+	struct cvmx_pko_mem_debug4_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t curr_siz:8;
+		uint64_t curr_off:16;
+		uint64_t cmnd_segs:6;
+		uint64_t cmnd_siz:16;
+		uint64_t cmnd_off:6;
+		uint64_t uid:2;
+		uint64_t dread_sop:1;
+		uint64_t init_dwrite:1;
+		uint64_t chk_once:1;
+		uint64_t chk_mode:1;
+		uint64_t wait:1;
+		uint64_t minor:2;
+		uint64_t major:3;
+#else
+		uint64_t major:3;
+		uint64_t minor:2;
+		uint64_t wait:1;
+		uint64_t chk_mode:1;
+		uint64_t chk_once:1;
+		uint64_t init_dwrite:1;
+		uint64_t dread_sop:1;
+		uint64_t uid:2;
+		uint64_t cmnd_off:6;
+		uint64_t cmnd_siz:16;
+		uint64_t cmnd_segs:6;
+		uint64_t curr_off:16;
+		uint64_t curr_siz:8;
+#endif
+	} cn52xx;
+};
+
+union cvmx_pko_mem_debug5 {
+	uint64_t u64;
+	struct cvmx_pko_mem_debug5_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_0_63:64;
+#else
+		uint64_t reserved_0_63:64;
+#endif
+	} s;
+	struct cvmx_pko_mem_debug5_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t dwri_mod:1;
+		uint64_t dwri_sop:1;
+		uint64_t dwri_len:1;
+		uint64_t dwri_cnt:13;
+		uint64_t cmnd_siz:16;
+		uint64_t uid:1;
+		uint64_t xfer_wor:1;
+		uint64_t xfer_dwr:1;
+		uint64_t cbuf_fre:1;
+		uint64_t reserved_27_27:1;
+		uint64_t chk_mode:1;
+		uint64_t active:1;
+		uint64_t qos:3;
+		uint64_t qcb_ridx:5;
+		uint64_t qid_off:3;
+		uint64_t qid_base:7;
+		uint64_t wait:1;
+		uint64_t minor:2;
+		uint64_t major:4;
+#else
+		uint64_t major:4;
+		uint64_t minor:2;
+		uint64_t wait:1;
+		uint64_t qid_base:7;
+		uint64_t qid_off:3;
+		uint64_t qcb_ridx:5;
+		uint64_t qos:3;
+		uint64_t active:1;
+		uint64_t chk_mode:1;
+		uint64_t reserved_27_27:1;
+		uint64_t cbuf_fre:1;
+		uint64_t xfer_dwr:1;
+		uint64_t xfer_wor:1;
+		uint64_t uid:1;
+		uint64_t cmnd_siz:16;
+		uint64_t dwri_cnt:13;
+		uint64_t dwri_len:1;
+		uint64_t dwri_sop:1;
+		uint64_t dwri_mod:1;
+#endif
+	} cn30xx;
+	struct cvmx_pko_mem_debug5_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t curr_ptr:29;
+		uint64_t curr_siz:16;
+		uint64_t curr_off:16;
+		uint64_t cmnd_segs:3;
+#else
+		uint64_t cmnd_segs:3;
+		uint64_t curr_off:16;
+		uint64_t curr_siz:16;
+		uint64_t curr_ptr:29;
+#endif
+	} cn50xx;
+	struct cvmx_pko_mem_debug5_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_54_63:10;
+		uint64_t nxt_inflt:6;
+		uint64_t curr_ptr:40;
+		uint64_t curr_siz:8;
+#else
+		uint64_t curr_siz:8;
+		uint64_t curr_ptr:40;
+		uint64_t nxt_inflt:6;
+		uint64_t reserved_54_63:10;
+#endif
+	} cn52xx;
+	struct cvmx_pko_mem_debug5_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_56_63:8;
+		uint64_t ptp:1;
+		uint64_t major_3:1;
+		uint64_t nxt_inflt:6;
+		uint64_t curr_ptr:40;
+		uint64_t curr_siz:8;
+#else
+		uint64_t curr_siz:8;
+		uint64_t curr_ptr:40;
+		uint64_t nxt_inflt:6;
+		uint64_t major_3:1;
+		uint64_t ptp:1;
+		uint64_t reserved_56_63:8;
+#endif
+	} cn61xx;
+	struct cvmx_pko_mem_debug5_cn68xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_57_63:7;
+		uint64_t uid_2:1;
+		uint64_t ptp:1;
+		uint64_t major_3:1;
+		uint64_t nxt_inflt:6;
+		uint64_t curr_ptr:40;
+		uint64_t curr_siz:8;
+#else
+		uint64_t curr_siz:8;
+		uint64_t curr_ptr:40;
+		uint64_t nxt_inflt:6;
+		uint64_t major_3:1;
+		uint64_t ptp:1;
+		uint64_t uid_2:1;
+		uint64_t reserved_57_63:7;
+#endif
+	} cn68xx;
+};
+
+union cvmx_pko_mem_debug6 {
+	uint64_t u64;
+	struct cvmx_pko_mem_debug6_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_37_63:27;
+		uint64_t qid_offres:4;
+		uint64_t qid_offths:4;
+		uint64_t preempter:1;
+		uint64_t preemptee:1;
+		uint64_t preempted:1;
+		uint64_t active:1;
+		uint64_t statc:1;
+		uint64_t qos:3;
+		uint64_t qcb_ridx:5;
+		uint64_t qid_offmax:4;
+		uint64_t reserved_0_11:12;
+#else
+		uint64_t reserved_0_11:12;
+		uint64_t qid_offmax:4;
+		uint64_t qcb_ridx:5;
+		uint64_t qos:3;
+		uint64_t statc:1;
+		uint64_t active:1;
+		uint64_t preempted:1;
+		uint64_t preemptee:1;
+		uint64_t preempter:1;
+		uint64_t qid_offths:4;
+		uint64_t qid_offres:4;
+		uint64_t reserved_37_63:27;
+#endif
+	} s;
+	struct cvmx_pko_mem_debug6_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_11_63:53;
+		uint64_t qid_offm:3;
+		uint64_t static_p:1;
+		uint64_t work_min:3;
+		uint64_t dwri_chk:1;
+		uint64_t dwri_uid:1;
+		uint64_t dwri_mod:2;
+#else
+		uint64_t dwri_mod:2;
+		uint64_t dwri_uid:1;
+		uint64_t dwri_chk:1;
+		uint64_t work_min:3;
+		uint64_t static_p:1;
+		uint64_t qid_offm:3;
+		uint64_t reserved_11_63:53;
+#endif
+	} cn30xx;
+	struct cvmx_pko_mem_debug6_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_11_63:53;
+		uint64_t curr_ptr:11;
+#else
+		uint64_t curr_ptr:11;
+		uint64_t reserved_11_63:53;
+#endif
+	} cn50xx;
+	struct cvmx_pko_mem_debug6_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_37_63:27;
+		uint64_t qid_offres:4;
+		uint64_t qid_offths:4;
+		uint64_t preempter:1;
+		uint64_t preemptee:1;
+		uint64_t preempted:1;
+		uint64_t active:1;
+		uint64_t statc:1;
+		uint64_t qos:3;
+		uint64_t qcb_ridx:5;
+		uint64_t qid_offmax:4;
+		uint64_t qid_off:4;
+		uint64_t qid_base:8;
+#else
+		uint64_t qid_base:8;
+		uint64_t qid_off:4;
+		uint64_t qid_offmax:4;
+		uint64_t qcb_ridx:5;
+		uint64_t qos:3;
+		uint64_t statc:1;
+		uint64_t active:1;
+		uint64_t preempted:1;
+		uint64_t preemptee:1;
+		uint64_t preempter:1;
+		uint64_t qid_offths:4;
+		uint64_t qid_offres:4;
+		uint64_t reserved_37_63:27;
+#endif
+	} cn52xx;
+};
+
+union cvmx_pko_mem_debug7 {
+	uint64_t u64;
+	struct cvmx_pko_mem_debug7_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_0_63:64;
+#else
+		uint64_t reserved_0_63:64;
+#endif
+	} s;
+	struct cvmx_pko_mem_debug7_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_58_63:6;
+		uint64_t dwb:9;
+		uint64_t start:33;
+		uint64_t size:16;
+#else
+		uint64_t size:16;
+		uint64_t start:33;
+		uint64_t dwb:9;
+		uint64_t reserved_58_63:6;
+#endif
+	} cn30xx;
+	struct cvmx_pko_mem_debug7_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t qos:5;
+		uint64_t tail:1;
+		uint64_t buf_siz:13;
+		uint64_t buf_ptr:33;
+		uint64_t qcb_widx:6;
+		uint64_t qcb_ridx:6;
+#else
+		uint64_t qcb_ridx:6;
+		uint64_t qcb_widx:6;
+		uint64_t buf_ptr:33;
+		uint64_t buf_siz:13;
+		uint64_t tail:1;
+		uint64_t qos:5;
+#endif
+	} cn50xx;
+	struct cvmx_pko_mem_debug7_cn68xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t qos:3;
+		uint64_t tail:1;
+		uint64_t buf_siz:13;
+		uint64_t buf_ptr:33;
+		uint64_t qcb_widx:7;
+		uint64_t qcb_ridx:7;
+#else
+		uint64_t qcb_ridx:7;
+		uint64_t qcb_widx:7;
+		uint64_t buf_ptr:33;
+		uint64_t buf_siz:13;
+		uint64_t tail:1;
+		uint64_t qos:3;
+#endif
+	} cn68xx;
+};
+
+union cvmx_pko_mem_debug8 {
+	uint64_t u64;
+	struct cvmx_pko_mem_debug8_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_59_63:5;
+		uint64_t tail:1;
+		uint64_t buf_siz:13;
+		uint64_t reserved_0_44:45;
+#else
+		uint64_t reserved_0_44:45;
+		uint64_t buf_siz:13;
+		uint64_t tail:1;
+		uint64_t reserved_59_63:5;
+#endif
+	} s;
+	struct cvmx_pko_mem_debug8_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t qos:5;
+		uint64_t tail:1;
+		uint64_t buf_siz:13;
+		uint64_t buf_ptr:33;
+		uint64_t qcb_widx:6;
+		uint64_t qcb_ridx:6;
+#else
+		uint64_t qcb_ridx:6;
+		uint64_t qcb_widx:6;
+		uint64_t buf_ptr:33;
+		uint64_t buf_siz:13;
+		uint64_t tail:1;
+		uint64_t qos:5;
+#endif
+	} cn30xx;
+	struct cvmx_pko_mem_debug8_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_28_63:36;
+		uint64_t doorbell:20;
+		uint64_t reserved_6_7:2;
+		uint64_t static_p:1;
+		uint64_t s_tail:1;
+		uint64_t static_q:1;
+		uint64_t qos:3;
+#else
+		uint64_t qos:3;
+		uint64_t static_q:1;
+		uint64_t s_tail:1;
+		uint64_t static_p:1;
+		uint64_t reserved_6_7:2;
+		uint64_t doorbell:20;
+		uint64_t reserved_28_63:36;
+#endif
+	} cn50xx;
+	struct cvmx_pko_mem_debug8_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t preempter:1;
+		uint64_t doorbell:20;
+		uint64_t reserved_7_7:1;
+		uint64_t preemptee:1;
+		uint64_t static_p:1;
+		uint64_t s_tail:1;
+		uint64_t static_q:1;
+		uint64_t qos:3;
+#else
+		uint64_t qos:3;
+		uint64_t static_q:1;
+		uint64_t s_tail:1;
+		uint64_t static_p:1;
+		uint64_t preemptee:1;
+		uint64_t reserved_7_7:1;
+		uint64_t doorbell:20;
+		uint64_t preempter:1;
+		uint64_t reserved_29_63:35;
+#endif
+	} cn52xx;
+	struct cvmx_pko_mem_debug8_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_42_63:22;
+		uint64_t qid_qqos:8;
+		uint64_t reserved_33_33:1;
+		uint64_t qid_idx:4;
+		uint64_t preempter:1;
+		uint64_t doorbell:20;
+		uint64_t reserved_7_7:1;
+		uint64_t preemptee:1;
+		uint64_t static_p:1;
+		uint64_t s_tail:1;
+		uint64_t static_q:1;
+		uint64_t qos:3;
+#else
+		uint64_t qos:3;
+		uint64_t static_q:1;
+		uint64_t s_tail:1;
+		uint64_t static_p:1;
+		uint64_t preemptee:1;
+		uint64_t reserved_7_7:1;
+		uint64_t doorbell:20;
+		uint64_t preempter:1;
+		uint64_t qid_idx:4;
+		uint64_t reserved_33_33:1;
+		uint64_t qid_qqos:8;
+		uint64_t reserved_42_63:22;
+#endif
+	} cn61xx;
+	struct cvmx_pko_mem_debug8_cn68xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_37_63:27;
+		uint64_t preempter:1;
+		uint64_t doorbell:20;
+		uint64_t reserved_9_15:7;
+		uint64_t preemptee:1;
+		uint64_t static_p:1;
+		uint64_t s_tail:1;
+		uint64_t static_q:1;
+		uint64_t qos:5;
+#else
+		uint64_t qos:5;
+		uint64_t static_q:1;
+		uint64_t s_tail:1;
+		uint64_t static_p:1;
+		uint64_t preemptee:1;
+		uint64_t reserved_9_15:7;
+		uint64_t doorbell:20;
+		uint64_t preempter:1;
+		uint64_t reserved_37_63:27;
+#endif
+	} cn68xx;
+};
+
+union cvmx_pko_mem_debug9 {
+	uint64_t u64;
+	struct cvmx_pko_mem_debug9_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_49_63:15;
+		uint64_t ptrs0:17;
+		uint64_t reserved_0_31:32;
+#else
+		uint64_t reserved_0_31:32;
+		uint64_t ptrs0:17;
+		uint64_t reserved_49_63:15;
+#endif
+	} s;
+	struct cvmx_pko_mem_debug9_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_28_63:36;
+		uint64_t doorbell:20;
+		uint64_t reserved_5_7:3;
+		uint64_t s_tail:1;
+		uint64_t static_q:1;
+		uint64_t qos:3;
+#else
+		uint64_t qos:3;
+		uint64_t static_q:1;
+		uint64_t s_tail:1;
+		uint64_t reserved_5_7:3;
+		uint64_t doorbell:20;
+		uint64_t reserved_28_63:36;
+#endif
+	} cn30xx;
+	struct cvmx_pko_mem_debug9_cn38xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_28_63:36;
+		uint64_t doorbell:20;
+		uint64_t reserved_6_7:2;
+		uint64_t static_p:1;
+		uint64_t s_tail:1;
+		uint64_t static_q:1;
+		uint64_t qos:3;
+#else
+		uint64_t qos:3;
+		uint64_t static_q:1;
+		uint64_t s_tail:1;
+		uint64_t static_p:1;
+		uint64_t reserved_6_7:2;
+		uint64_t doorbell:20;
+		uint64_t reserved_28_63:36;
+#endif
+	} cn38xx;
+	struct cvmx_pko_mem_debug9_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_49_63:15;
+		uint64_t ptrs0:17;
+		uint64_t reserved_17_31:15;
+		uint64_t ptrs3:17;
+#else
+		uint64_t ptrs3:17;
+		uint64_t reserved_17_31:15;
+		uint64_t ptrs0:17;
+		uint64_t reserved_49_63:15;
+#endif
+	} cn50xx;
+};
+
+union cvmx_pko_mem_iport_ptrs {
+	uint64_t u64;
+	struct cvmx_pko_mem_iport_ptrs_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_63_63:1;
+		uint64_t crc:1;
+		uint64_t static_p:1;
+		uint64_t qos_mask:8;
+		uint64_t min_pkt:3;
+		uint64_t reserved_31_49:19;
+		uint64_t pipe:7;
+		uint64_t reserved_21_23:3;
+		uint64_t intr:5;
+		uint64_t reserved_13_15:3;
+		uint64_t eid:5;
+		uint64_t reserved_7_7:1;
+		uint64_t ipid:7;
+#else
+		uint64_t ipid:7;
+		uint64_t reserved_7_7:1;
+		uint64_t eid:5;
+		uint64_t reserved_13_15:3;
+		uint64_t intr:5;
+		uint64_t reserved_21_23:3;
+		uint64_t pipe:7;
+		uint64_t reserved_31_49:19;
+		uint64_t min_pkt:3;
+		uint64_t qos_mask:8;
+		uint64_t static_p:1;
+		uint64_t crc:1;
+		uint64_t reserved_63_63:1;
+#endif
+	} s;
+};
+
+union cvmx_pko_mem_iport_qos {
+	uint64_t u64;
+	struct cvmx_pko_mem_iport_qos_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_61_63:3;
+		uint64_t qos_mask:8;
+		uint64_t reserved_13_52:40;
+		uint64_t eid:5;
+		uint64_t reserved_7_7:1;
+		uint64_t ipid:7;
+#else
+		uint64_t ipid:7;
+		uint64_t reserved_7_7:1;
+		uint64_t eid:5;
+		uint64_t reserved_13_52:40;
+		uint64_t qos_mask:8;
+		uint64_t reserved_61_63:3;
+#endif
+	} s;
+};
+
+union cvmx_pko_mem_iqueue_ptrs {
+	uint64_t u64;
+	struct cvmx_pko_mem_iqueue_ptrs_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t s_tail:1;
+		uint64_t static_p:1;
+		uint64_t static_q:1;
+		uint64_t qos_mask:8;
+		uint64_t buf_ptr:31;
+		uint64_t tail:1;
+		uint64_t index:5;
+		uint64_t reserved_15_15:1;
+		uint64_t ipid:7;
+		uint64_t qid:8;
+#else
+		uint64_t qid:8;
+		uint64_t ipid:7;
+		uint64_t reserved_15_15:1;
+		uint64_t index:5;
+		uint64_t tail:1;
+		uint64_t buf_ptr:31;
+		uint64_t qos_mask:8;
+		uint64_t static_q:1;
+		uint64_t static_p:1;
+		uint64_t s_tail:1;
+#endif
+	} s;
+};
+
+union cvmx_pko_mem_iqueue_qos {
+	uint64_t u64;
+	struct cvmx_pko_mem_iqueue_qos_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_61_63:3;
+		uint64_t qos_mask:8;
+		uint64_t reserved_15_52:38;
+		uint64_t ipid:7;
+		uint64_t qid:8;
+#else
+		uint64_t qid:8;
+		uint64_t ipid:7;
+		uint64_t reserved_15_52:38;
+		uint64_t qos_mask:8;
+		uint64_t reserved_61_63:3;
+#endif
+	} s;
+};
+
+union cvmx_pko_mem_port_ptrs {
+	uint64_t u64;
+	struct cvmx_pko_mem_port_ptrs_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_62_63:2;
+		uint64_t static_p:1;
+		uint64_t qos_mask:8;
+		uint64_t reserved_16_52:37;
+		uint64_t bp_port:6;
+		uint64_t eid:4;
+		uint64_t pid:6;
+#else
+		uint64_t pid:6;
+		uint64_t eid:4;
+		uint64_t bp_port:6;
+		uint64_t reserved_16_52:37;
+		uint64_t qos_mask:8;
+		uint64_t static_p:1;
+		uint64_t reserved_62_63:2;
+#endif
+	} s;
+};
+
+union cvmx_pko_mem_port_qos {
+	uint64_t u64;
+	struct cvmx_pko_mem_port_qos_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_61_63:3;
+		uint64_t qos_mask:8;
+		uint64_t reserved_10_52:43;
+		uint64_t eid:4;
+		uint64_t pid:6;
+#else
+		uint64_t pid:6;
+		uint64_t eid:4;
+		uint64_t reserved_10_52:43;
+		uint64_t qos_mask:8;
+		uint64_t reserved_61_63:3;
+#endif
+	} s;
+};
+
+union cvmx_pko_mem_port_rate0 {
+	uint64_t u64;
+	struct cvmx_pko_mem_port_rate0_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_51_63:13;
+		uint64_t rate_word:19;
+		uint64_t rate_pkt:24;
+		uint64_t reserved_7_7:1;
+		uint64_t pid:7;
+#else
+		uint64_t pid:7;
+		uint64_t reserved_7_7:1;
+		uint64_t rate_pkt:24;
+		uint64_t rate_word:19;
+		uint64_t reserved_51_63:13;
+#endif
+	} s;
+	struct cvmx_pko_mem_port_rate0_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_51_63:13;
+		uint64_t rate_word:19;
+		uint64_t rate_pkt:24;
+		uint64_t reserved_6_7:2;
+		uint64_t pid:6;
+#else
+		uint64_t pid:6;
+		uint64_t reserved_6_7:2;
+		uint64_t rate_pkt:24;
+		uint64_t rate_word:19;
+		uint64_t reserved_51_63:13;
+#endif
+	} cn52xx;
+};
+
+union cvmx_pko_mem_port_rate1 {
+	uint64_t u64;
+	struct cvmx_pko_mem_port_rate1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t rate_lim:24;
+		uint64_t reserved_7_7:1;
+		uint64_t pid:7;
+#else
+		uint64_t pid:7;
+		uint64_t reserved_7_7:1;
+		uint64_t rate_lim:24;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+	struct cvmx_pko_mem_port_rate1_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t rate_lim:24;
+		uint64_t reserved_6_7:2;
+		uint64_t pid:6;
+#else
+		uint64_t pid:6;
+		uint64_t reserved_6_7:2;
+		uint64_t rate_lim:24;
+		uint64_t reserved_32_63:32;
+#endif
+	} cn52xx;
+};
+
+union cvmx_pko_mem_queue_ptrs {
+	uint64_t u64;
+	struct cvmx_pko_mem_queue_ptrs_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t s_tail:1;
+		uint64_t static_p:1;
+		uint64_t static_q:1;
+		uint64_t qos_mask:8;
+		uint64_t buf_ptr:36;
+		uint64_t tail:1;
+		uint64_t index:3;
+		uint64_t port:6;
+		uint64_t queue:7;
+#else
+		uint64_t queue:7;
+		uint64_t port:6;
+		uint64_t index:3;
+		uint64_t tail:1;
+		uint64_t buf_ptr:36;
+		uint64_t qos_mask:8;
+		uint64_t static_q:1;
+		uint64_t static_p:1;
+		uint64_t s_tail:1;
+#endif
+	} s;
+};
+
+union cvmx_pko_mem_queue_qos {
+	uint64_t u64;
+	struct cvmx_pko_mem_queue_qos_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_61_63:3;
+		uint64_t qos_mask:8;
+		uint64_t reserved_13_52:40;
+		uint64_t pid:6;
+		uint64_t qid:7;
+#else
+		uint64_t qid:7;
+		uint64_t pid:6;
+		uint64_t reserved_13_52:40;
+		uint64_t qos_mask:8;
+		uint64_t reserved_61_63:3;
+#endif
+	} s;
+};
+
+union cvmx_pko_mem_throttle_int {
+	uint64_t u64;
+	struct cvmx_pko_mem_throttle_int_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_47_63:17;
+		uint64_t word:15;
+		uint64_t reserved_14_31:18;
+		uint64_t packet:6;
+		uint64_t reserved_5_7:3;
+		uint64_t intr:5;
+#else
+		uint64_t intr:5;
+		uint64_t reserved_5_7:3;
+		uint64_t packet:6;
+		uint64_t reserved_14_31:18;
+		uint64_t word:15;
+		uint64_t reserved_47_63:17;
+#endif
+	} s;
+};
+
+union cvmx_pko_mem_throttle_pipe {
+	uint64_t u64;
+	struct cvmx_pko_mem_throttle_pipe_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_47_63:17;
+		uint64_t word:15;
+		uint64_t reserved_14_31:18;
+		uint64_t packet:6;
+		uint64_t reserved_7_7:1;
+		uint64_t pipe:7;
+#else
+		uint64_t pipe:7;
+		uint64_t reserved_7_7:1;
+		uint64_t packet:6;
+		uint64_t reserved_14_31:18;
+		uint64_t word:15;
+		uint64_t reserved_47_63:17;
+#endif
+	} s;
+};
+
+union cvmx_pko_reg_bist_result {
+	uint64_t u64;
+	struct cvmx_pko_reg_bist_result_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_0_63:64;
+#else
+		uint64_t reserved_0_63:64;
+#endif
+	} s;
+	struct cvmx_pko_reg_bist_result_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_27_63:37;
+		uint64_t psb2:5;
+		uint64_t count:1;
+		uint64_t rif:1;
+		uint64_t wif:1;
+		uint64_t ncb:1;
+		uint64_t out:1;
+		uint64_t crc:1;
+		uint64_t chk:1;
+		uint64_t qsb:2;
+		uint64_t qcb:2;
+		uint64_t pdb:4;
+		uint64_t psb:7;
+#else
+		uint64_t psb:7;
+		uint64_t pdb:4;
+		uint64_t qcb:2;
+		uint64_t qsb:2;
+		uint64_t chk:1;
+		uint64_t crc:1;
+		uint64_t out:1;
+		uint64_t ncb:1;
+		uint64_t wif:1;
+		uint64_t rif:1;
+		uint64_t count:1;
+		uint64_t psb2:5;
+		uint64_t reserved_27_63:37;
+#endif
+	} cn30xx;
+	struct cvmx_pko_reg_bist_result_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_33_63:31;
+		uint64_t csr:1;
+		uint64_t iob:1;
+		uint64_t out_crc:1;
+		uint64_t out_ctl:3;
+		uint64_t out_sta:1;
+		uint64_t out_wif:1;
+		uint64_t prt_chk:3;
+		uint64_t prt_nxt:1;
+		uint64_t prt_psb:6;
+		uint64_t ncb_inb:2;
+		uint64_t prt_qcb:2;
+		uint64_t prt_qsb:3;
+		uint64_t dat_dat:4;
+		uint64_t dat_ptr:4;
+#else
+		uint64_t dat_ptr:4;
+		uint64_t dat_dat:4;
+		uint64_t prt_qsb:3;
+		uint64_t prt_qcb:2;
+		uint64_t ncb_inb:2;
+		uint64_t prt_psb:6;
+		uint64_t prt_nxt:1;
+		uint64_t prt_chk:3;
+		uint64_t out_wif:1;
+		uint64_t out_sta:1;
+		uint64_t out_ctl:3;
+		uint64_t out_crc:1;
+		uint64_t iob:1;
+		uint64_t csr:1;
+		uint64_t reserved_33_63:31;
+#endif
+	} cn50xx;
+	struct cvmx_pko_reg_bist_result_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_35_63:29;
+		uint64_t csr:1;
+		uint64_t iob:1;
+		uint64_t out_dat:1;
+		uint64_t out_ctl:3;
+		uint64_t out_sta:1;
+		uint64_t out_wif:1;
+		uint64_t prt_chk:3;
+		uint64_t prt_nxt:1;
+		uint64_t prt_psb:8;
+		uint64_t ncb_inb:2;
+		uint64_t prt_qcb:2;
+		uint64_t prt_qsb:3;
+		uint64_t prt_ctl:2;
+		uint64_t dat_dat:2;
+		uint64_t dat_ptr:4;
+#else
+		uint64_t dat_ptr:4;
+		uint64_t dat_dat:2;
+		uint64_t prt_ctl:2;
+		uint64_t prt_qsb:3;
+		uint64_t prt_qcb:2;
+		uint64_t ncb_inb:2;
+		uint64_t prt_psb:8;
+		uint64_t prt_nxt:1;
+		uint64_t prt_chk:3;
+		uint64_t out_wif:1;
+		uint64_t out_sta:1;
+		uint64_t out_ctl:3;
+		uint64_t out_dat:1;
+		uint64_t iob:1;
+		uint64_t csr:1;
+		uint64_t reserved_35_63:29;
+#endif
+	} cn52xx;
+	struct cvmx_pko_reg_bist_result_cn68xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_36_63:28;
+		uint64_t crc:1;
+		uint64_t csr:1;
+		uint64_t iob:1;
+		uint64_t out_dat:1;
+		uint64_t reserved_31_31:1;
+		uint64_t out_ctl:2;
+		uint64_t out_sta:1;
+		uint64_t out_wif:1;
+		uint64_t prt_chk:3;
+		uint64_t prt_nxt:1;
+		uint64_t prt_psb7:1;
+		uint64_t reserved_21_21:1;
+		uint64_t prt_psb:6;
+		uint64_t ncb_inb:2;
+		uint64_t prt_qcb:2;
+		uint64_t prt_qsb:3;
+		uint64_t prt_ctl:2;
+		uint64_t dat_dat:2;
+		uint64_t dat_ptr:4;
+#else
+		uint64_t dat_ptr:4;
+		uint64_t dat_dat:2;
+		uint64_t prt_ctl:2;
+		uint64_t prt_qsb:3;
+		uint64_t prt_qcb:2;
+		uint64_t ncb_inb:2;
+		uint64_t prt_psb:6;
+		uint64_t reserved_21_21:1;
+		uint64_t prt_psb7:1;
+		uint64_t prt_nxt:1;
+		uint64_t prt_chk:3;
+		uint64_t out_wif:1;
+		uint64_t out_sta:1;
+		uint64_t out_ctl:2;
+		uint64_t reserved_31_31:1;
+		uint64_t out_dat:1;
+		uint64_t iob:1;
+		uint64_t csr:1;
+		uint64_t crc:1;
+		uint64_t reserved_36_63:28;
+#endif
+	} cn68xx;
+	struct cvmx_pko_reg_bist_result_cn68xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_35_63:29;
+		uint64_t csr:1;
+		uint64_t iob:1;
+		uint64_t out_dat:1;
+		uint64_t reserved_31_31:1;
+		uint64_t out_ctl:2;
+		uint64_t out_sta:1;
+		uint64_t out_wif:1;
+		uint64_t prt_chk:3;
+		uint64_t prt_nxt:1;
+		uint64_t prt_psb7:1;
+		uint64_t reserved_21_21:1;
+		uint64_t prt_psb:6;
+		uint64_t ncb_inb:2;
+		uint64_t prt_qcb:2;
+		uint64_t prt_qsb:3;
+		uint64_t prt_ctl:2;
+		uint64_t dat_dat:2;
+		uint64_t dat_ptr:4;
+#else
+		uint64_t dat_ptr:4;
+		uint64_t dat_dat:2;
+		uint64_t prt_ctl:2;
+		uint64_t prt_qsb:3;
+		uint64_t prt_qcb:2;
+		uint64_t ncb_inb:2;
+		uint64_t prt_psb:6;
+		uint64_t reserved_21_21:1;
+		uint64_t prt_psb7:1;
+		uint64_t prt_nxt:1;
+		uint64_t prt_chk:3;
+		uint64_t out_wif:1;
+		uint64_t out_sta:1;
+		uint64_t out_ctl:2;
+		uint64_t reserved_31_31:1;
+		uint64_t out_dat:1;
+		uint64_t iob:1;
+		uint64_t csr:1;
+		uint64_t reserved_35_63:29;
+#endif
+	} cn68xxp1;
+};
+
+union cvmx_pko_reg_cmd_buf {
+	uint64_t u64;
+	struct cvmx_pko_reg_cmd_buf_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_23_63:41;
+		uint64_t pool:3;
+		uint64_t reserved_13_19:7;
+		uint64_t size:13;
+#else
+		uint64_t size:13;
+		uint64_t reserved_13_19:7;
+		uint64_t pool:3;
+		uint64_t reserved_23_63:41;
+#endif
+	} s;
+};
+
+union cvmx_pko_reg_crc_ctlx {
+	uint64_t u64;
+	struct cvmx_pko_reg_crc_ctlx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t invres:1;
+		uint64_t refin:1;
+#else
+		uint64_t refin:1;
+		uint64_t invres:1;
+		uint64_t reserved_2_63:62;
+#endif
+	} s;
+};
+
+union cvmx_pko_reg_crc_enable {
+	uint64_t u64;
+	struct cvmx_pko_reg_crc_enable_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t enable:32;
+#else
+		uint64_t enable:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_pko_reg_crc_ivx {
+	uint64_t u64;
+	struct cvmx_pko_reg_crc_ivx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t iv:32;
+#else
+		uint64_t iv:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_pko_reg_debug0 {
+	uint64_t u64;
+	struct cvmx_pko_reg_debug0_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t asserts:64;
+#else
+		uint64_t asserts:64;
+#endif
+	} s;
+	struct cvmx_pko_reg_debug0_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_17_63:47;
+		uint64_t asserts:17;
+#else
+		uint64_t asserts:17;
+		uint64_t reserved_17_63:47;
+#endif
+	} cn30xx;
+};
+
+union cvmx_pko_reg_debug1 {
+	uint64_t u64;
+	struct cvmx_pko_reg_debug1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t asserts:64;
+#else
+		uint64_t asserts:64;
+#endif
+	} s;
+};
+
+union cvmx_pko_reg_debug2 {
+	uint64_t u64;
+	struct cvmx_pko_reg_debug2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t asserts:64;
+#else
+		uint64_t asserts:64;
+#endif
+	} s;
+};
+
+union cvmx_pko_reg_debug3 {
+	uint64_t u64;
+	struct cvmx_pko_reg_debug3_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t asserts:64;
+#else
+		uint64_t asserts:64;
+#endif
+	} s;
+};
+
+union cvmx_pko_reg_debug4 {
+	uint64_t u64;
+	struct cvmx_pko_reg_debug4_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t asserts:64;
+#else
+		uint64_t asserts:64;
+#endif
+	} s;
+};
+
+union cvmx_pko_reg_engine_inflight {
+	uint64_t u64;
+	struct cvmx_pko_reg_engine_inflight_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t engine15:4;
+		uint64_t engine14:4;
+		uint64_t engine13:4;
+		uint64_t engine12:4;
+		uint64_t engine11:4;
+		uint64_t engine10:4;
+		uint64_t engine9:4;
+		uint64_t engine8:4;
+		uint64_t engine7:4;
+		uint64_t engine6:4;
+		uint64_t engine5:4;
+		uint64_t engine4:4;
+		uint64_t engine3:4;
+		uint64_t engine2:4;
+		uint64_t engine1:4;
+		uint64_t engine0:4;
+#else
+		uint64_t engine0:4;
+		uint64_t engine1:4;
+		uint64_t engine2:4;
+		uint64_t engine3:4;
+		uint64_t engine4:4;
+		uint64_t engine5:4;
+		uint64_t engine6:4;
+		uint64_t engine7:4;
+		uint64_t engine8:4;
+		uint64_t engine9:4;
+		uint64_t engine10:4;
+		uint64_t engine11:4;
+		uint64_t engine12:4;
+		uint64_t engine13:4;
+		uint64_t engine14:4;
+		uint64_t engine15:4;
+#endif
+	} s;
+	struct cvmx_pko_reg_engine_inflight_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_40_63:24;
+		uint64_t engine9:4;
+		uint64_t engine8:4;
+		uint64_t engine7:4;
+		uint64_t engine6:4;
+		uint64_t engine5:4;
+		uint64_t engine4:4;
+		uint64_t engine3:4;
+		uint64_t engine2:4;
+		uint64_t engine1:4;
+		uint64_t engine0:4;
+#else
+		uint64_t engine0:4;
+		uint64_t engine1:4;
+		uint64_t engine2:4;
+		uint64_t engine3:4;
+		uint64_t engine4:4;
+		uint64_t engine5:4;
+		uint64_t engine6:4;
+		uint64_t engine7:4;
+		uint64_t engine8:4;
+		uint64_t engine9:4;
+		uint64_t reserved_40_63:24;
+#endif
+	} cn52xx;
+	struct cvmx_pko_reg_engine_inflight_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_56_63:8;
+		uint64_t engine13:4;
+		uint64_t engine12:4;
+		uint64_t engine11:4;
+		uint64_t engine10:4;
+		uint64_t engine9:4;
+		uint64_t engine8:4;
+		uint64_t engine7:4;
+		uint64_t engine6:4;
+		uint64_t engine5:4;
+		uint64_t engine4:4;
+		uint64_t engine3:4;
+		uint64_t engine2:4;
+		uint64_t engine1:4;
+		uint64_t engine0:4;
+#else
+		uint64_t engine0:4;
+		uint64_t engine1:4;
+		uint64_t engine2:4;
+		uint64_t engine3:4;
+		uint64_t engine4:4;
+		uint64_t engine5:4;
+		uint64_t engine6:4;
+		uint64_t engine7:4;
+		uint64_t engine8:4;
+		uint64_t engine9:4;
+		uint64_t engine10:4;
+		uint64_t engine11:4;
+		uint64_t engine12:4;
+		uint64_t engine13:4;
+		uint64_t reserved_56_63:8;
+#endif
+	} cn61xx;
+	struct cvmx_pko_reg_engine_inflight_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t engine11:4;
+		uint64_t engine10:4;
+		uint64_t engine9:4;
+		uint64_t engine8:4;
+		uint64_t engine7:4;
+		uint64_t engine6:4;
+		uint64_t engine5:4;
+		uint64_t engine4:4;
+		uint64_t engine3:4;
+		uint64_t engine2:4;
+		uint64_t engine1:4;
+		uint64_t engine0:4;
+#else
+		uint64_t engine0:4;
+		uint64_t engine1:4;
+		uint64_t engine2:4;
+		uint64_t engine3:4;
+		uint64_t engine4:4;
+		uint64_t engine5:4;
+		uint64_t engine6:4;
+		uint64_t engine7:4;
+		uint64_t engine8:4;
+		uint64_t engine9:4;
+		uint64_t engine10:4;
+		uint64_t engine11:4;
+		uint64_t reserved_48_63:16;
+#endif
+	} cn63xx;
+};
+
+union cvmx_pko_reg_engine_inflight1 {
+	uint64_t u64;
+	struct cvmx_pko_reg_engine_inflight1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t engine19:4;
+		uint64_t engine18:4;
+		uint64_t engine17:4;
+		uint64_t engine16:4;
+#else
+		uint64_t engine16:4;
+		uint64_t engine17:4;
+		uint64_t engine18:4;
+		uint64_t engine19:4;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_pko_reg_engine_storagex {
+	uint64_t u64;
+	struct cvmx_pko_reg_engine_storagex_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t engine15:4;
+		uint64_t engine14:4;
+		uint64_t engine13:4;
+		uint64_t engine12:4;
+		uint64_t engine11:4;
+		uint64_t engine10:4;
+		uint64_t engine9:4;
+		uint64_t engine8:4;
+		uint64_t engine7:4;
+		uint64_t engine6:4;
+		uint64_t engine5:4;
+		uint64_t engine4:4;
+		uint64_t engine3:4;
+		uint64_t engine2:4;
+		uint64_t engine1:4;
+		uint64_t engine0:4;
+#else
+		uint64_t engine0:4;
+		uint64_t engine1:4;
+		uint64_t engine2:4;
+		uint64_t engine3:4;
+		uint64_t engine4:4;
+		uint64_t engine5:4;
+		uint64_t engine6:4;
+		uint64_t engine7:4;
+		uint64_t engine8:4;
+		uint64_t engine9:4;
+		uint64_t engine10:4;
+		uint64_t engine11:4;
+		uint64_t engine12:4;
+		uint64_t engine13:4;
+		uint64_t engine14:4;
+		uint64_t engine15:4;
+#endif
+	} s;
+};
+
+union cvmx_pko_reg_engine_thresh {
+	uint64_t u64;
+	struct cvmx_pko_reg_engine_thresh_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t mask:20;
+#else
+		uint64_t mask:20;
+		uint64_t reserved_20_63:44;
+#endif
+	} s;
+	struct cvmx_pko_reg_engine_thresh_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t mask:10;
+#else
+		uint64_t mask:10;
+		uint64_t reserved_10_63:54;
+#endif
+	} cn52xx;
+	struct cvmx_pko_reg_engine_thresh_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_14_63:50;
+		uint64_t mask:14;
+#else
+		uint64_t mask:14;
+		uint64_t reserved_14_63:50;
+#endif
+	} cn61xx;
+	struct cvmx_pko_reg_engine_thresh_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t mask:12;
+#else
+		uint64_t mask:12;
+		uint64_t reserved_12_63:52;
+#endif
+	} cn63xx;
+};
+
+union cvmx_pko_reg_error {
+	uint64_t u64;
+	struct cvmx_pko_reg_error_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t loopback:1;
+		uint64_t currzero:1;
+		uint64_t doorbell:1;
+		uint64_t parity:1;
+#else
+		uint64_t parity:1;
+		uint64_t doorbell:1;
+		uint64_t currzero:1;
+		uint64_t loopback:1;
+		uint64_t reserved_4_63:60;
+#endif
+	} s;
+	struct cvmx_pko_reg_error_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t doorbell:1;
+		uint64_t parity:1;
+#else
+		uint64_t parity:1;
+		uint64_t doorbell:1;
+		uint64_t reserved_2_63:62;
+#endif
+	} cn30xx;
+	struct cvmx_pko_reg_error_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_3_63:61;
+		uint64_t currzero:1;
+		uint64_t doorbell:1;
+		uint64_t parity:1;
+#else
+		uint64_t parity:1;
+		uint64_t doorbell:1;
+		uint64_t currzero:1;
+		uint64_t reserved_3_63:61;
+#endif
+	} cn50xx;
+};
+
+union cvmx_pko_reg_flags {
+	uint64_t u64;
+	struct cvmx_pko_reg_flags_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_9_63:55;
+		uint64_t dis_perf3:1;
+		uint64_t dis_perf2:1;
+		uint64_t dis_perf1:1;
+		uint64_t dis_perf0:1;
+		uint64_t ena_throttle:1;
+		uint64_t reset:1;
+		uint64_t store_be:1;
+		uint64_t ena_dwb:1;
+		uint64_t ena_pko:1;
+#else
+		uint64_t ena_pko:1;
+		uint64_t ena_dwb:1;
+		uint64_t store_be:1;
+		uint64_t reset:1;
+		uint64_t ena_throttle:1;
+		uint64_t dis_perf0:1;
+		uint64_t dis_perf1:1;
+		uint64_t dis_perf2:1;
+		uint64_t dis_perf3:1;
+		uint64_t reserved_9_63:55;
+#endif
+	} s;
+	struct cvmx_pko_reg_flags_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t reset:1;
+		uint64_t store_be:1;
+		uint64_t ena_dwb:1;
+		uint64_t ena_pko:1;
+#else
+		uint64_t ena_pko:1;
+		uint64_t ena_dwb:1;
+		uint64_t store_be:1;
+		uint64_t reset:1;
+		uint64_t reserved_4_63:60;
+#endif
+	} cn30xx;
+	struct cvmx_pko_reg_flags_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_9_63:55;
+		uint64_t dis_perf3:1;
+		uint64_t dis_perf2:1;
+		uint64_t reserved_4_6:3;
+		uint64_t reset:1;
+		uint64_t store_be:1;
+		uint64_t ena_dwb:1;
+		uint64_t ena_pko:1;
+#else
+		uint64_t ena_pko:1;
+		uint64_t ena_dwb:1;
+		uint64_t store_be:1;
+		uint64_t reset:1;
+		uint64_t reserved_4_6:3;
+		uint64_t dis_perf2:1;
+		uint64_t dis_perf3:1;
+		uint64_t reserved_9_63:55;
+#endif
+	} cn61xx;
+	struct cvmx_pko_reg_flags_cn68xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t dis_perf1:1;
+		uint64_t dis_perf0:1;
+		uint64_t ena_throttle:1;
+		uint64_t reset:1;
+		uint64_t store_be:1;
+		uint64_t ena_dwb:1;
+		uint64_t ena_pko:1;
+#else
+		uint64_t ena_pko:1;
+		uint64_t ena_dwb:1;
+		uint64_t store_be:1;
+		uint64_t reset:1;
+		uint64_t ena_throttle:1;
+		uint64_t dis_perf0:1;
+		uint64_t dis_perf1:1;
+		uint64_t reserved_7_63:57;
+#endif
+	} cn68xxp1;
+};
+
+union cvmx_pko_reg_gmx_port_mode {
+	uint64_t u64;
+	struct cvmx_pko_reg_gmx_port_mode_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t mode1:3;
+		uint64_t mode0:3;
+#else
+		uint64_t mode0:3;
+		uint64_t mode1:3;
+		uint64_t reserved_6_63:58;
+#endif
+	} s;
+};
+
+union cvmx_pko_reg_int_mask {
+	uint64_t u64;
+	struct cvmx_pko_reg_int_mask_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t loopback:1;
+		uint64_t currzero:1;
+		uint64_t doorbell:1;
+		uint64_t parity:1;
+#else
+		uint64_t parity:1;
+		uint64_t doorbell:1;
+		uint64_t currzero:1;
+		uint64_t loopback:1;
+		uint64_t reserved_4_63:60;
+#endif
+	} s;
+	struct cvmx_pko_reg_int_mask_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t doorbell:1;
+		uint64_t parity:1;
+#else
+		uint64_t parity:1;
+		uint64_t doorbell:1;
+		uint64_t reserved_2_63:62;
+#endif
+	} cn30xx;
+	struct cvmx_pko_reg_int_mask_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_3_63:61;
+		uint64_t currzero:1;
+		uint64_t doorbell:1;
+		uint64_t parity:1;
+#else
+		uint64_t parity:1;
+		uint64_t doorbell:1;
+		uint64_t currzero:1;
+		uint64_t reserved_3_63:61;
+#endif
+	} cn50xx;
+};
+
+union cvmx_pko_reg_loopback_bpid {
+	uint64_t u64;
+	struct cvmx_pko_reg_loopback_bpid_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_59_63:5;
+		uint64_t bpid7:6;
+		uint64_t reserved_52_52:1;
+		uint64_t bpid6:6;
+		uint64_t reserved_45_45:1;
+		uint64_t bpid5:6;
+		uint64_t reserved_38_38:1;
+		uint64_t bpid4:6;
+		uint64_t reserved_31_31:1;
+		uint64_t bpid3:6;
+		uint64_t reserved_24_24:1;
+		uint64_t bpid2:6;
+		uint64_t reserved_17_17:1;
+		uint64_t bpid1:6;
+		uint64_t reserved_10_10:1;
+		uint64_t bpid0:6;
+		uint64_t reserved_0_3:4;
+#else
+		uint64_t reserved_0_3:4;
+		uint64_t bpid0:6;
+		uint64_t reserved_10_10:1;
+		uint64_t bpid1:6;
+		uint64_t reserved_17_17:1;
+		uint64_t bpid2:6;
+		uint64_t reserved_24_24:1;
+		uint64_t bpid3:6;
+		uint64_t reserved_31_31:1;
+		uint64_t bpid4:6;
+		uint64_t reserved_38_38:1;
+		uint64_t bpid5:6;
+		uint64_t reserved_45_45:1;
+		uint64_t bpid6:6;
+		uint64_t reserved_52_52:1;
+		uint64_t bpid7:6;
+		uint64_t reserved_59_63:5;
+#endif
+	} s;
+};
+
+union cvmx_pko_reg_loopback_pkind {
+	uint64_t u64;
+	struct cvmx_pko_reg_loopback_pkind_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_59_63:5;
+		uint64_t pkind7:6;
+		uint64_t reserved_52_52:1;
+		uint64_t pkind6:6;
+		uint64_t reserved_45_45:1;
+		uint64_t pkind5:6;
+		uint64_t reserved_38_38:1;
+		uint64_t pkind4:6;
+		uint64_t reserved_31_31:1;
+		uint64_t pkind3:6;
+		uint64_t reserved_24_24:1;
+		uint64_t pkind2:6;
+		uint64_t reserved_17_17:1;
+		uint64_t pkind1:6;
+		uint64_t reserved_10_10:1;
+		uint64_t pkind0:6;
+		uint64_t num_ports:4;
+#else
+		uint64_t num_ports:4;
+		uint64_t pkind0:6;
+		uint64_t reserved_10_10:1;
+		uint64_t pkind1:6;
+		uint64_t reserved_17_17:1;
+		uint64_t pkind2:6;
+		uint64_t reserved_24_24:1;
+		uint64_t pkind3:6;
+		uint64_t reserved_31_31:1;
+		uint64_t pkind4:6;
+		uint64_t reserved_38_38:1;
+		uint64_t pkind5:6;
+		uint64_t reserved_45_45:1;
+		uint64_t pkind6:6;
+		uint64_t reserved_52_52:1;
+		uint64_t pkind7:6;
+		uint64_t reserved_59_63:5;
+#endif
+	} s;
+};
+
+union cvmx_pko_reg_min_pkt {
+	uint64_t u64;
+	struct cvmx_pko_reg_min_pkt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t size7:8;
+		uint64_t size6:8;
+		uint64_t size5:8;
+		uint64_t size4:8;
+		uint64_t size3:8;
+		uint64_t size2:8;
+		uint64_t size1:8;
+		uint64_t size0:8;
+#else
+		uint64_t size0:8;
+		uint64_t size1:8;
+		uint64_t size2:8;
+		uint64_t size3:8;
+		uint64_t size4:8;
+		uint64_t size5:8;
+		uint64_t size6:8;
+		uint64_t size7:8;
+#endif
+	} s;
+};
+
+union cvmx_pko_reg_preempt {
+	uint64_t u64;
+	struct cvmx_pko_reg_preempt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t min_size:16;
+#else
+		uint64_t min_size:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_pko_reg_queue_mode {
+	uint64_t u64;
+	struct cvmx_pko_reg_queue_mode_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t mode:2;
+#else
+		uint64_t mode:2;
+		uint64_t reserved_2_63:62;
+#endif
+	} s;
+};
+
+union cvmx_pko_reg_queue_preempt {
+	uint64_t u64;
+	struct cvmx_pko_reg_queue_preempt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t preemptee:1;
+		uint64_t preempter:1;
+#else
+		uint64_t preempter:1;
+		uint64_t preemptee:1;
+		uint64_t reserved_2_63:62;
+#endif
+	} s;
+};
+
+union cvmx_pko_reg_queue_ptrs1 {
+	uint64_t u64;
+	struct cvmx_pko_reg_queue_ptrs1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t idx3:1;
+		uint64_t qid7:1;
+#else
+		uint64_t qid7:1;
+		uint64_t idx3:1;
+		uint64_t reserved_2_63:62;
+#endif
+	} s;
+};
+
+union cvmx_pko_reg_read_idx {
+	uint64_t u64;
+	struct cvmx_pko_reg_read_idx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t inc:8;
+		uint64_t index:8;
+#else
+		uint64_t index:8;
+		uint64_t inc:8;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_pko_reg_throttle {
+	uint64_t u64;
+	struct cvmx_pko_reg_throttle_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t int_mask:32;
+#else
+		uint64_t int_mask:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_pko_reg_timestamp {
+	uint64_t u64;
+	struct cvmx_pko_reg_timestamp_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t wqe_word:4;
+#else
+		uint64_t wqe_word:4;
+		uint64_t reserved_4_63:60;
+#endif
+	} s;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-pko.h b/arch/mips/include/asm/octeon/cvmx-pko.h
new file mode 100644
index 000000000..5fec8476e
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-pko.h
@@ -0,0 +1,642 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/**
+ *
+ * Interface to the hardware Packet Output unit.
+ *
+ * Starting with SDK 1.7.0, the PKO output functions now support
+ * two types of locking. CVMX_PKO_LOCK_ATOMIC_TAG continues to
+ * function similarly to previous SDKs by using POW atomic tags
+ * to preserve ordering and exclusivity. As a new option, you
+ * can now pass CVMX_PKO_LOCK_CMD_QUEUE which uses a ll/sc
+ * memory based locking instead. This locking has the advantage
+ * of not affecting the tag state but doesn't preserve packet
+ * ordering. CVMX_PKO_LOCK_CMD_QUEUE is appropriate in most
+ * generic code while CVMX_PKO_LOCK_CMD_QUEUE should be used
+ * with hand tuned fast path code.
+ *
+ * Some of other SDK differences visible to the command queuing:
+ * - PKO indexes are no longer stored in the FAU. A large
+ *   percentage of the FAU register block used to be tied up
+ *   maintaining PKO queue pointers. These are now stored in a
+ *   global named block.
+ * - The PKO <b>use_locking</b> parameter can now have a global
+ *   effect. Since all application use the same named block,
+ *   queue locking correctly applies across all operating
+ *   systems when using CVMX_PKO_LOCK_CMD_QUEUE.
+ * - PKO 3 word commands are now supported. Use
+ *   cvmx_pko_send_packet_finish3().
+ *
+ */
+
+#ifndef __CVMX_PKO_H__
+#define __CVMX_PKO_H__
+
+#include <asm/octeon/cvmx-fpa.h>
+#include <asm/octeon/cvmx-pow.h>
+#include <asm/octeon/cvmx-cmd-queue.h>
+#include <asm/octeon/cvmx-pko-defs.h>
+
+/* Adjust the command buffer size by 1 word so that in the case of using only
+ * two word PKO commands no command words stradle buffers.  The useful values
+ * for this are 0 and 1. */
+#define CVMX_PKO_COMMAND_BUFFER_SIZE_ADJUST (1)
+
+#define CVMX_PKO_MAX_OUTPUT_QUEUES_STATIC 256
+#define CVMX_PKO_MAX_OUTPUT_QUEUES	((OCTEON_IS_MODEL(OCTEON_CN31XX) || \
+	OCTEON_IS_MODEL(OCTEON_CN3010) || OCTEON_IS_MODEL(OCTEON_CN3005) || \
+	OCTEON_IS_MODEL(OCTEON_CN50XX)) ? 32 : \
+		(OCTEON_IS_MODEL(OCTEON_CN58XX) || \
+		OCTEON_IS_MODEL(OCTEON_CN56XX)) ? 256 : 128)
+#define CVMX_PKO_NUM_OUTPUT_PORTS	40
+/* use this for queues that are not used */
+#define CVMX_PKO_MEM_QUEUE_PTRS_ILLEGAL_PID 63
+#define CVMX_PKO_QUEUE_STATIC_PRIORITY	9
+#define CVMX_PKO_ILLEGAL_QUEUE	0xFFFF
+#define CVMX_PKO_MAX_QUEUE_DEPTH 0
+
+typedef enum {
+	CVMX_PKO_SUCCESS,
+	CVMX_PKO_INVALID_PORT,
+	CVMX_PKO_INVALID_QUEUE,
+	CVMX_PKO_INVALID_PRIORITY,
+	CVMX_PKO_NO_MEMORY,
+	CVMX_PKO_PORT_ALREADY_SETUP,
+	CVMX_PKO_CMD_QUEUE_INIT_ERROR
+} cvmx_pko_status_t;
+
+/**
+ * This enumeration represents the differnet locking modes supported by PKO.
+ */
+typedef enum {
+	/*
+	 * PKO doesn't do any locking. It is the responsibility of the
+	 * application to make sure that no other core is accessing
+	 * the same queue at the same time
+	 */
+	CVMX_PKO_LOCK_NONE = 0,
+	/*
+	 * PKO performs an atomic tagswitch to insure exclusive access
+	 * to the output queue. This will maintain packet ordering on
+	 * output.
+	 */
+	CVMX_PKO_LOCK_ATOMIC_TAG = 1,
+	/*
+	 * PKO uses the common command queue locks to insure exclusive
+	 * access to the output queue. This is a memory based
+	 * ll/sc. This is the most portable locking mechanism.
+	 */
+	CVMX_PKO_LOCK_CMD_QUEUE = 2,
+} cvmx_pko_lock_t;
+
+typedef struct {
+	uint32_t packets;
+	uint64_t octets;
+	uint64_t doorbell;
+} cvmx_pko_port_status_t;
+
+/**
+ * This structure defines the address to use on a packet enqueue
+ */
+typedef union {
+	uint64_t u64;
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		/* Must CVMX_IO_SEG */
+		uint64_t mem_space:2;
+		/* Must be zero */
+		uint64_t reserved:13;
+		/* Must be one */
+		uint64_t is_io:1;
+		/* The ID of the device on the non-coherent bus */
+		uint64_t did:8;
+		/* Must be zero */
+		uint64_t reserved2:4;
+		/* Must be zero */
+		uint64_t reserved3:18;
+		/*
+		 * The hardware likes to have the output port in
+		 * addition to the output queue,
+		 */
+		uint64_t port:6;
+		/*
+		 * The output queue to send the packet to (0-127 are
+		 * legal)
+		 */
+		uint64_t queue:9;
+		/* Must be zero */
+		uint64_t reserved4:3;
+#else
+	        uint64_t reserved4:3;
+	        uint64_t queue:9;
+	        uint64_t port:9;
+	        uint64_t reserved3:15;
+	        uint64_t reserved2:4;
+	        uint64_t did:8;
+	        uint64_t is_io:1;
+	        uint64_t reserved:13;
+	        uint64_t mem_space:2;
+#endif
+	} s;
+} cvmx_pko_doorbell_address_t;
+
+/**
+ * Structure of the first packet output command word.
+ */
+union cvmx_pko_command_word0 {
+	uint64_t u64;
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		/*
+		 * The size of the reg1 operation - could be 8, 16,
+		 * 32, or 64 bits.
+		 */
+		uint64_t size1:2;
+		/*
+		 * The size of the reg0 operation - could be 8, 16,
+		 * 32, or 64 bits.
+		 */
+		uint64_t size0:2;
+		/*
+		 * If set, subtract 1, if clear, subtract packet
+		 * size.
+		 */
+		uint64_t subone1:1;
+		/*
+		 * The register, subtract will be done if reg1 is
+		 * non-zero.
+		 */
+		uint64_t reg1:11;
+		/* If set, subtract 1, if clear, subtract packet size */
+		uint64_t subone0:1;
+		/* The register, subtract will be done if reg0 is non-zero */
+		uint64_t reg0:11;
+		/*
+		 * When set, interpret segment pointer and segment
+		 * bytes in little endian order.
+		 */
+		uint64_t le:1;
+		/*
+		 * When set, packet data not allocated in L2 cache by
+		 * PKO.
+		 */
+		uint64_t n2:1;
+		/*
+		 * If set and rsp is set, word3 contains a pointer to
+		 * a work queue entry.
+		 */
+		uint64_t wqp:1;
+		/* If set, the hardware will send a response when done */
+		uint64_t rsp:1;
+		/*
+		 * If set, the supplied pkt_ptr is really a pointer to
+		 * a list of pkt_ptr's.
+		 */
+		uint64_t gather:1;
+		/*
+		 * If ipoffp1 is non zero, (ipoffp1-1) is the number
+		 * of bytes to IP header, and the hardware will
+		 * calculate and insert the UDP/TCP checksum.
+		 */
+		uint64_t ipoffp1:7;
+		/*
+		 * If set, ignore the I bit (force to zero) from all
+		 * pointer structures.
+		 */
+		uint64_t ignore_i:1;
+		/*
+		 * If clear, the hardware will attempt to free the
+		 * buffers containing the packet.
+		 */
+		uint64_t dontfree:1;
+		/*
+		 * The total number of segs in the packet, if gather
+		 * set, also gather list length.
+		 */
+		uint64_t segs:6;
+		/* Including L2, but no trailing CRC */
+		uint64_t total_bytes:16;
+#else
+	        uint64_t total_bytes:16;
+	        uint64_t segs:6;
+	        uint64_t dontfree:1;
+	        uint64_t ignore_i:1;
+	        uint64_t ipoffp1:7;
+	        uint64_t gather:1;
+	        uint64_t rsp:1;
+	        uint64_t wqp:1;
+	        uint64_t n2:1;
+	        uint64_t le:1;
+	        uint64_t reg0:11;
+	        uint64_t subone0:1;
+	        uint64_t reg1:11;
+	        uint64_t subone1:1;
+	        uint64_t size0:2;
+	        uint64_t size1:2;
+#endif
+	} s;
+};
+
+/* CSR typedefs have been moved to cvmx-csr-*.h */
+
+/**
+ * Definition of internal state for Packet output processing
+ */
+typedef struct {
+	/* ptr to start of buffer, offset kept in FAU reg */
+	uint64_t *start_ptr;
+} cvmx_pko_state_elem_t;
+
+/**
+ * Call before any other calls to initialize the packet
+ * output system.
+ */
+extern void cvmx_pko_initialize_global(void);
+
+/**
+ * Enables the packet output hardware. It must already be
+ * configured.
+ */
+extern void cvmx_pko_enable(void);
+
+/**
+ * Disables the packet output. Does not affect any configuration.
+ */
+extern void cvmx_pko_disable(void);
+
+/**
+ * Shutdown and free resources required by packet output.
+ */
+
+extern void cvmx_pko_shutdown(void);
+
+/**
+ * Configure a output port and the associated queues for use.
+ *
+ * @port:	Port to configure.
+ * @base_queue: First queue number to associate with this port.
+ * @num_queues: Number of queues t oassociate with this port
+ * @priority:	Array of priority levels for each queue. Values are
+ *		     allowed to be 1-8. A value of 8 get 8 times the traffic
+ *		     of a value of 1. There must be num_queues elements in the
+ *		     array.
+ */
+extern cvmx_pko_status_t cvmx_pko_config_port(uint64_t port,
+					      uint64_t base_queue,
+					      uint64_t num_queues,
+					      const uint64_t priority[]);
+
+/**
+ * Ring the packet output doorbell. This tells the packet
+ * output hardware that "len" command words have been added
+ * to its pending list.	 This command includes the required
+ * CVMX_SYNCWS before the doorbell ring.
+ *
+ * @port:   Port the packet is for
+ * @queue:  Queue the packet is for
+ * @len:    Length of the command in 64 bit words
+ */
+static inline void cvmx_pko_doorbell(uint64_t port, uint64_t queue,
+				     uint64_t len)
+{
+	cvmx_pko_doorbell_address_t ptr;
+
+	ptr.u64 = 0;
+	ptr.s.mem_space = CVMX_IO_SEG;
+	ptr.s.did = CVMX_OCT_DID_PKT_SEND;
+	ptr.s.is_io = 1;
+	ptr.s.port = port;
+	ptr.s.queue = queue;
+	/*
+	 * Need to make sure output queue data is in DRAM before
+	 * doorbell write.
+	 */
+	CVMX_SYNCWS;
+	cvmx_write_io(ptr.u64, len);
+}
+
+/**
+ * Prepare to send a packet.  This may initiate a tag switch to
+ * get exclusive access to the output queue structure, and
+ * performs other prep work for the packet send operation.
+ *
+ * cvmx_pko_send_packet_finish() MUST be called after this function is called,
+ * and must be called with the same port/queue/use_locking arguments.
+ *
+ * The use_locking parameter allows the caller to use three
+ * possible locking modes.
+ * - CVMX_PKO_LOCK_NONE
+ *	- PKO doesn't do any locking. It is the responsibility
+ *	    of the application to make sure that no other core
+ *	    is accessing the same queue at the same time.
+ * - CVMX_PKO_LOCK_ATOMIC_TAG
+ *	- PKO performs an atomic tagswitch to insure exclusive
+ *	    access to the output queue. This will maintain
+ *	    packet ordering on output.
+ * - CVMX_PKO_LOCK_CMD_QUEUE
+ *	- PKO uses the common command queue locks to insure
+ *	    exclusive access to the output queue. This is a
+ *	    memory based ll/sc. This is the most portable
+ *	    locking mechanism.
+ *
+ * NOTE: If atomic locking is used, the POW entry CANNOT be
+ * descheduled, as it does not contain a valid WQE pointer.
+ *
+ * @port:   Port to send it on
+ * @queue:  Queue to use
+ * @use_locking: CVMX_PKO_LOCK_NONE, CVMX_PKO_LOCK_ATOMIC_TAG, or
+ *		 CVMX_PKO_LOCK_CMD_QUEUE
+ */
+
+static inline void cvmx_pko_send_packet_prepare(uint64_t port, uint64_t queue,
+						cvmx_pko_lock_t use_locking)
+{
+	if (use_locking == CVMX_PKO_LOCK_ATOMIC_TAG) {
+		/*
+		 * Must do a full switch here to handle all cases.  We
+		 * use a fake WQE pointer, as the POW does not access
+		 * this memory.	 The WQE pointer and group are only
+		 * used if this work is descheduled, which is not
+		 * supported by the
+		 * cvmx_pko_send_packet_prepare/cvmx_pko_send_packet_finish
+		 * combination.	 Note that this is a special case in
+		 * which these fake values can be used - this is not a
+		 * general technique.
+		 */
+		uint32_t tag =
+		    CVMX_TAG_SW_BITS_INTERNAL << CVMX_TAG_SW_SHIFT |
+		    CVMX_TAG_SUBGROUP_PKO << CVMX_TAG_SUBGROUP_SHIFT |
+		    (CVMX_TAG_SUBGROUP_MASK & queue);
+		cvmx_pow_tag_sw_full((struct cvmx_wqe *) cvmx_phys_to_ptr(0x80), tag,
+				     CVMX_POW_TAG_TYPE_ATOMIC, 0);
+	}
+}
+
+/**
+ * Complete packet output. cvmx_pko_send_packet_prepare() must be
+ * called exactly once before this, and the same parameters must be
+ * passed to both cvmx_pko_send_packet_prepare() and
+ * cvmx_pko_send_packet_finish().
+ *
+ * @port:   Port to send it on
+ * @queue:  Queue to use
+ * @pko_command:
+ *		 PKO HW command word
+ * @packet: Packet to send
+ * @use_locking: CVMX_PKO_LOCK_NONE, CVMX_PKO_LOCK_ATOMIC_TAG, or
+ *		 CVMX_PKO_LOCK_CMD_QUEUE
+ *
+ * Returns: CVMX_PKO_SUCCESS on success, or error code on
+ * failure of output
+ */
+static inline cvmx_pko_status_t cvmx_pko_send_packet_finish(
+	uint64_t port,
+	uint64_t queue,
+	union cvmx_pko_command_word0 pko_command,
+	union cvmx_buf_ptr packet,
+	cvmx_pko_lock_t use_locking)
+{
+	cvmx_cmd_queue_result_t result;
+	if (use_locking == CVMX_PKO_LOCK_ATOMIC_TAG)
+		cvmx_pow_tag_sw_wait();
+	result = cvmx_cmd_queue_write2(CVMX_CMD_QUEUE_PKO(queue),
+				       (use_locking == CVMX_PKO_LOCK_CMD_QUEUE),
+				       pko_command.u64, packet.u64);
+	if (likely(result == CVMX_CMD_QUEUE_SUCCESS)) {
+		cvmx_pko_doorbell(port, queue, 2);
+		return CVMX_PKO_SUCCESS;
+	} else if ((result == CVMX_CMD_QUEUE_NO_MEMORY)
+		   || (result == CVMX_CMD_QUEUE_FULL)) {
+		return CVMX_PKO_NO_MEMORY;
+	} else {
+		return CVMX_PKO_INVALID_QUEUE;
+	}
+}
+
+/**
+ * Complete packet output. cvmx_pko_send_packet_prepare() must be
+ * called exactly once before this, and the same parameters must be
+ * passed to both cvmx_pko_send_packet_prepare() and
+ * cvmx_pko_send_packet_finish().
+ *
+ * @port:   Port to send it on
+ * @queue:  Queue to use
+ * @pko_command:
+ *		 PKO HW command word
+ * @packet: Packet to send
+ * @addr: Plysical address of a work queue entry or physical address
+ *	  to zero on complete.
+ * @use_locking: CVMX_PKO_LOCK_NONE, CVMX_PKO_LOCK_ATOMIC_TAG, or
+ *		 CVMX_PKO_LOCK_CMD_QUEUE
+ *
+ * Returns: CVMX_PKO_SUCCESS on success, or error code on
+ * failure of output
+ */
+static inline cvmx_pko_status_t cvmx_pko_send_packet_finish3(
+	uint64_t port,
+	uint64_t queue,
+	union cvmx_pko_command_word0 pko_command,
+	union cvmx_buf_ptr packet,
+	uint64_t addr,
+	cvmx_pko_lock_t use_locking)
+{
+	cvmx_cmd_queue_result_t result;
+	if (use_locking == CVMX_PKO_LOCK_ATOMIC_TAG)
+		cvmx_pow_tag_sw_wait();
+	result = cvmx_cmd_queue_write3(CVMX_CMD_QUEUE_PKO(queue),
+				       (use_locking == CVMX_PKO_LOCK_CMD_QUEUE),
+				       pko_command.u64, packet.u64, addr);
+	if (likely(result == CVMX_CMD_QUEUE_SUCCESS)) {
+		cvmx_pko_doorbell(port, queue, 3);
+		return CVMX_PKO_SUCCESS;
+	} else if ((result == CVMX_CMD_QUEUE_NO_MEMORY)
+		   || (result == CVMX_CMD_QUEUE_FULL)) {
+		return CVMX_PKO_NO_MEMORY;
+	} else {
+		return CVMX_PKO_INVALID_QUEUE;
+	}
+}
+
+/**
+ * Return the pko output queue associated with a port and a specific core.
+ * In normal mode (PKO lockless operation is disabled), the value returned
+ * is the base queue.
+ *
+ * @port:   Port number
+ * @core:   Core to get queue for
+ *
+ * Returns Core-specific output queue
+ */
+static inline int cvmx_pko_get_base_queue_per_core(int port, int core)
+{
+#ifndef CVMX_HELPER_PKO_MAX_PORTS_INTERFACE0
+#define CVMX_HELPER_PKO_MAX_PORTS_INTERFACE0 16
+#endif
+#ifndef CVMX_HELPER_PKO_MAX_PORTS_INTERFACE1
+#define CVMX_HELPER_PKO_MAX_PORTS_INTERFACE1 16
+#endif
+
+	if (port < CVMX_PKO_MAX_PORTS_INTERFACE0)
+		return port * CVMX_PKO_QUEUES_PER_PORT_INTERFACE0 + core;
+	else if (port >= 16 && port < 16 + CVMX_PKO_MAX_PORTS_INTERFACE1)
+		return CVMX_PKO_MAX_PORTS_INTERFACE0 *
+		    CVMX_PKO_QUEUES_PER_PORT_INTERFACE0 + (port -
+							   16) *
+		    CVMX_PKO_QUEUES_PER_PORT_INTERFACE1 + core;
+	else if ((port >= 32) && (port < 36))
+		return CVMX_PKO_MAX_PORTS_INTERFACE0 *
+		    CVMX_PKO_QUEUES_PER_PORT_INTERFACE0 +
+		    CVMX_PKO_MAX_PORTS_INTERFACE1 *
+		    CVMX_PKO_QUEUES_PER_PORT_INTERFACE1 + (port -
+							   32) *
+		    CVMX_PKO_QUEUES_PER_PORT_PCI;
+	else if ((port >= 36) && (port < 40))
+		return CVMX_PKO_MAX_PORTS_INTERFACE0 *
+		    CVMX_PKO_QUEUES_PER_PORT_INTERFACE0 +
+		    CVMX_PKO_MAX_PORTS_INTERFACE1 *
+		    CVMX_PKO_QUEUES_PER_PORT_INTERFACE1 +
+		    4 * CVMX_PKO_QUEUES_PER_PORT_PCI + (port -
+							36) *
+		    CVMX_PKO_QUEUES_PER_PORT_LOOP;
+	else
+		/* Given the limit on the number of ports we can map to
+		 * CVMX_MAX_OUTPUT_QUEUES_STATIC queues (currently 256,
+		 * divided among all cores), the remaining unmapped ports
+		 * are assigned an illegal queue number */
+		return CVMX_PKO_ILLEGAL_QUEUE;
+}
+
+/**
+ * For a given port number, return the base pko output queue
+ * for the port.
+ *
+ * @port:   Port number
+ * Returns Base output queue
+ */
+static inline int cvmx_pko_get_base_queue(int port)
+{
+	if (OCTEON_IS_MODEL(OCTEON_CN68XX))
+		return port;
+
+	return cvmx_pko_get_base_queue_per_core(port, 0);
+}
+
+/**
+ * For a given port number, return the number of pko output queues.
+ *
+ * @port:   Port number
+ * Returns Number of output queues
+ */
+static inline int cvmx_pko_get_num_queues(int port)
+{
+	if (port < 16)
+		return CVMX_PKO_QUEUES_PER_PORT_INTERFACE0;
+	else if (port < 32)
+		return CVMX_PKO_QUEUES_PER_PORT_INTERFACE1;
+	else if (port < 36)
+		return CVMX_PKO_QUEUES_PER_PORT_PCI;
+	else if (port < 40)
+		return CVMX_PKO_QUEUES_PER_PORT_LOOP;
+	else
+		return 0;
+}
+
+/**
+ * Get the status counters for a port.
+ *
+ * @port_num: Port number to get statistics for.
+ * @clear:    Set to 1 to clear the counters after they are read
+ * @status:   Where to put the results.
+ */
+static inline void cvmx_pko_get_port_status(uint64_t port_num, uint64_t clear,
+					    cvmx_pko_port_status_t *status)
+{
+	union cvmx_pko_reg_read_idx pko_reg_read_idx;
+	union cvmx_pko_mem_count0 pko_mem_count0;
+	union cvmx_pko_mem_count1 pko_mem_count1;
+
+	pko_reg_read_idx.u64 = 0;
+	pko_reg_read_idx.s.index = port_num;
+	cvmx_write_csr(CVMX_PKO_REG_READ_IDX, pko_reg_read_idx.u64);
+
+	pko_mem_count0.u64 = cvmx_read_csr(CVMX_PKO_MEM_COUNT0);
+	status->packets = pko_mem_count0.s.count;
+	if (clear) {
+		pko_mem_count0.s.count = port_num;
+		cvmx_write_csr(CVMX_PKO_MEM_COUNT0, pko_mem_count0.u64);
+	}
+
+	pko_mem_count1.u64 = cvmx_read_csr(CVMX_PKO_MEM_COUNT1);
+	status->octets = pko_mem_count1.s.count;
+	if (clear) {
+		pko_mem_count1.s.count = port_num;
+		cvmx_write_csr(CVMX_PKO_MEM_COUNT1, pko_mem_count1.u64);
+	}
+
+	if (OCTEON_IS_MODEL(OCTEON_CN3XXX)) {
+		union cvmx_pko_mem_debug9 debug9;
+		pko_reg_read_idx.s.index = cvmx_pko_get_base_queue(port_num);
+		cvmx_write_csr(CVMX_PKO_REG_READ_IDX, pko_reg_read_idx.u64);
+		debug9.u64 = cvmx_read_csr(CVMX_PKO_MEM_DEBUG9);
+		status->doorbell = debug9.cn38xx.doorbell;
+	} else {
+		union cvmx_pko_mem_debug8 debug8;
+		pko_reg_read_idx.s.index = cvmx_pko_get_base_queue(port_num);
+		cvmx_write_csr(CVMX_PKO_REG_READ_IDX, pko_reg_read_idx.u64);
+		debug8.u64 = cvmx_read_csr(CVMX_PKO_MEM_DEBUG8);
+		status->doorbell = debug8.cn50xx.doorbell;
+	}
+}
+
+/**
+ * Rate limit a PKO port to a max packets/sec. This function is only
+ * supported on CN57XX, CN56XX, CN55XX, and CN54XX.
+ *
+ * @port:      Port to rate limit
+ * @packets_s: Maximum packet/sec
+ * @burst:     Maximum number of packets to burst in a row before rate
+ *		    limiting cuts in.
+ *
+ * Returns Zero on success, negative on failure
+ */
+extern int cvmx_pko_rate_limit_packets(int port, int packets_s, int burst);
+
+/**
+ * Rate limit a PKO port to a max bits/sec. This function is only
+ * supported on CN57XX, CN56XX, CN55XX, and CN54XX.
+ *
+ * @port:   Port to rate limit
+ * @bits_s: PKO rate limit in bits/sec
+ * @burst:  Maximum number of bits to burst before rate
+ *		 limiting cuts in.
+ *
+ * Returns Zero on success, negative on failure
+ */
+extern int cvmx_pko_rate_limit_bits(int port, uint64_t bits_s, int burst);
+
+#endif /* __CVMX_PKO_H__ */
diff --git a/arch/mips/include/asm/octeon/cvmx-pow-defs.h b/arch/mips/include/asm/octeon/cvmx-pow-defs.h
new file mode 100644
index 000000000..474dd5443
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-pow-defs.h
@@ -0,0 +1,1001 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2012 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_POW_DEFS_H__
+#define __CVMX_POW_DEFS_H__
+
+#define CVMX_POW_BIST_STAT (CVMX_ADD_IO_SEG(0x00016700000003F8ull))
+#define CVMX_POW_DS_PC (CVMX_ADD_IO_SEG(0x0001670000000398ull))
+#define CVMX_POW_ECC_ERR (CVMX_ADD_IO_SEG(0x0001670000000218ull))
+#define CVMX_POW_INT_CTL (CVMX_ADD_IO_SEG(0x0001670000000220ull))
+#define CVMX_POW_IQ_CNTX(offset) (CVMX_ADD_IO_SEG(0x0001670000000340ull) + ((offset) & 7) * 8)
+#define CVMX_POW_IQ_COM_CNT (CVMX_ADD_IO_SEG(0x0001670000000388ull))
+#define CVMX_POW_IQ_INT (CVMX_ADD_IO_SEG(0x0001670000000238ull))
+#define CVMX_POW_IQ_INT_EN (CVMX_ADD_IO_SEG(0x0001670000000240ull))
+#define CVMX_POW_IQ_THRX(offset) (CVMX_ADD_IO_SEG(0x00016700000003A0ull) + ((offset) & 7) * 8)
+#define CVMX_POW_NOS_CNT (CVMX_ADD_IO_SEG(0x0001670000000228ull))
+#define CVMX_POW_NW_TIM (CVMX_ADD_IO_SEG(0x0001670000000210ull))
+#define CVMX_POW_PF_RST_MSK (CVMX_ADD_IO_SEG(0x0001670000000230ull))
+#define CVMX_POW_PP_GRP_MSKX(offset) (CVMX_ADD_IO_SEG(0x0001670000000000ull) + ((offset) & 15) * 8)
+#define CVMX_POW_QOS_RNDX(offset) (CVMX_ADD_IO_SEG(0x00016700000001C0ull) + ((offset) & 7) * 8)
+#define CVMX_POW_QOS_THRX(offset) (CVMX_ADD_IO_SEG(0x0001670000000180ull) + ((offset) & 7) * 8)
+#define CVMX_POW_TS_PC (CVMX_ADD_IO_SEG(0x0001670000000390ull))
+#define CVMX_POW_WA_COM_PC (CVMX_ADD_IO_SEG(0x0001670000000380ull))
+#define CVMX_POW_WA_PCX(offset) (CVMX_ADD_IO_SEG(0x0001670000000300ull) + ((offset) & 7) * 8)
+#define CVMX_POW_WQ_INT (CVMX_ADD_IO_SEG(0x0001670000000200ull))
+#define CVMX_POW_WQ_INT_CNTX(offset) (CVMX_ADD_IO_SEG(0x0001670000000100ull) + ((offset) & 15) * 8)
+#define CVMX_POW_WQ_INT_PC (CVMX_ADD_IO_SEG(0x0001670000000208ull))
+#define CVMX_POW_WQ_INT_THRX(offset) (CVMX_ADD_IO_SEG(0x0001670000000080ull) + ((offset) & 15) * 8)
+#define CVMX_POW_WS_PCX(offset) (CVMX_ADD_IO_SEG(0x0001670000000280ull) + ((offset) & 15) * 8)
+
+#define CVMX_SSO_WQ_INT (CVMX_ADD_IO_SEG(0x0001670000001000ull))
+#define CVMX_SSO_WQ_IQ_DIS (CVMX_ADD_IO_SEG(0x0001670000001010ull))
+#define CVMX_SSO_WQ_INT_PC (CVMX_ADD_IO_SEG(0x0001670000001020ull))
+#define CVMX_SSO_PPX_GRP_MSK(offset) (CVMX_ADD_IO_SEG(0x0001670000006000ull) + ((offset) & 31) * 8)
+#define CVMX_SSO_WQ_INT_THRX(offset) (CVMX_ADD_IO_SEG(0x0001670000007000ull) + ((offset) & 63) * 8)
+
+union cvmx_pow_bist_stat {
+	uint64_t u64;
+	struct cvmx_pow_bist_stat_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t pp:16;
+		uint64_t reserved_0_15:16;
+#else
+		uint64_t reserved_0_15:16;
+		uint64_t pp:16;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+	struct cvmx_pow_bist_stat_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_17_63:47;
+		uint64_t pp:1;
+		uint64_t reserved_9_15:7;
+		uint64_t cam:1;
+		uint64_t nbt1:1;
+		uint64_t nbt0:1;
+		uint64_t index:1;
+		uint64_t fidx:1;
+		uint64_t nbr1:1;
+		uint64_t nbr0:1;
+		uint64_t pend:1;
+		uint64_t adr:1;
+#else
+		uint64_t adr:1;
+		uint64_t pend:1;
+		uint64_t nbr0:1;
+		uint64_t nbr1:1;
+		uint64_t fidx:1;
+		uint64_t index:1;
+		uint64_t nbt0:1;
+		uint64_t nbt1:1;
+		uint64_t cam:1;
+		uint64_t reserved_9_15:7;
+		uint64_t pp:1;
+		uint64_t reserved_17_63:47;
+#endif
+	} cn30xx;
+	struct cvmx_pow_bist_stat_cn31xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_18_63:46;
+		uint64_t pp:2;
+		uint64_t reserved_9_15:7;
+		uint64_t cam:1;
+		uint64_t nbt1:1;
+		uint64_t nbt0:1;
+		uint64_t index:1;
+		uint64_t fidx:1;
+		uint64_t nbr1:1;
+		uint64_t nbr0:1;
+		uint64_t pend:1;
+		uint64_t adr:1;
+#else
+		uint64_t adr:1;
+		uint64_t pend:1;
+		uint64_t nbr0:1;
+		uint64_t nbr1:1;
+		uint64_t fidx:1;
+		uint64_t index:1;
+		uint64_t nbt0:1;
+		uint64_t nbt1:1;
+		uint64_t cam:1;
+		uint64_t reserved_9_15:7;
+		uint64_t pp:2;
+		uint64_t reserved_18_63:46;
+#endif
+	} cn31xx;
+	struct cvmx_pow_bist_stat_cn38xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t pp:16;
+		uint64_t reserved_10_15:6;
+		uint64_t cam:1;
+		uint64_t nbt:1;
+		uint64_t index:1;
+		uint64_t fidx:1;
+		uint64_t nbr1:1;
+		uint64_t nbr0:1;
+		uint64_t pend1:1;
+		uint64_t pend0:1;
+		uint64_t adr1:1;
+		uint64_t adr0:1;
+#else
+		uint64_t adr0:1;
+		uint64_t adr1:1;
+		uint64_t pend0:1;
+		uint64_t pend1:1;
+		uint64_t nbr0:1;
+		uint64_t nbr1:1;
+		uint64_t fidx:1;
+		uint64_t index:1;
+		uint64_t nbt:1;
+		uint64_t cam:1;
+		uint64_t reserved_10_15:6;
+		uint64_t pp:16;
+		uint64_t reserved_32_63:32;
+#endif
+	} cn38xx;
+	struct cvmx_pow_bist_stat_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t pp:4;
+		uint64_t reserved_9_15:7;
+		uint64_t cam:1;
+		uint64_t nbt1:1;
+		uint64_t nbt0:1;
+		uint64_t index:1;
+		uint64_t fidx:1;
+		uint64_t nbr1:1;
+		uint64_t nbr0:1;
+		uint64_t pend:1;
+		uint64_t adr:1;
+#else
+		uint64_t adr:1;
+		uint64_t pend:1;
+		uint64_t nbr0:1;
+		uint64_t nbr1:1;
+		uint64_t fidx:1;
+		uint64_t index:1;
+		uint64_t nbt0:1;
+		uint64_t nbt1:1;
+		uint64_t cam:1;
+		uint64_t reserved_9_15:7;
+		uint64_t pp:4;
+		uint64_t reserved_20_63:44;
+#endif
+	} cn52xx;
+	struct cvmx_pow_bist_stat_cn56xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_28_63:36;
+		uint64_t pp:12;
+		uint64_t reserved_10_15:6;
+		uint64_t cam:1;
+		uint64_t nbt:1;
+		uint64_t index:1;
+		uint64_t fidx:1;
+		uint64_t nbr1:1;
+		uint64_t nbr0:1;
+		uint64_t pend1:1;
+		uint64_t pend0:1;
+		uint64_t adr1:1;
+		uint64_t adr0:1;
+#else
+		uint64_t adr0:1;
+		uint64_t adr1:1;
+		uint64_t pend0:1;
+		uint64_t pend1:1;
+		uint64_t nbr0:1;
+		uint64_t nbr1:1;
+		uint64_t fidx:1;
+		uint64_t index:1;
+		uint64_t nbt:1;
+		uint64_t cam:1;
+		uint64_t reserved_10_15:6;
+		uint64_t pp:12;
+		uint64_t reserved_28_63:36;
+#endif
+	} cn56xx;
+	struct cvmx_pow_bist_stat_cn61xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t pp:4;
+		uint64_t reserved_12_15:4;
+		uint64_t cam:1;
+		uint64_t nbr:3;
+		uint64_t nbt:4;
+		uint64_t index:1;
+		uint64_t fidx:1;
+		uint64_t pend:1;
+		uint64_t adr:1;
+#else
+		uint64_t adr:1;
+		uint64_t pend:1;
+		uint64_t fidx:1;
+		uint64_t index:1;
+		uint64_t nbt:4;
+		uint64_t nbr:3;
+		uint64_t cam:1;
+		uint64_t reserved_12_15:4;
+		uint64_t pp:4;
+		uint64_t reserved_20_63:44;
+#endif
+	} cn61xx;
+	struct cvmx_pow_bist_stat_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_22_63:42;
+		uint64_t pp:6;
+		uint64_t reserved_12_15:4;
+		uint64_t cam:1;
+		uint64_t nbr:3;
+		uint64_t nbt:4;
+		uint64_t index:1;
+		uint64_t fidx:1;
+		uint64_t pend:1;
+		uint64_t adr:1;
+#else
+		uint64_t adr:1;
+		uint64_t pend:1;
+		uint64_t fidx:1;
+		uint64_t index:1;
+		uint64_t nbt:4;
+		uint64_t nbr:3;
+		uint64_t cam:1;
+		uint64_t reserved_12_15:4;
+		uint64_t pp:6;
+		uint64_t reserved_22_63:42;
+#endif
+	} cn63xx;
+	struct cvmx_pow_bist_stat_cn66xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_26_63:38;
+		uint64_t pp:10;
+		uint64_t reserved_12_15:4;
+		uint64_t cam:1;
+		uint64_t nbr:3;
+		uint64_t nbt:4;
+		uint64_t index:1;
+		uint64_t fidx:1;
+		uint64_t pend:1;
+		uint64_t adr:1;
+#else
+		uint64_t adr:1;
+		uint64_t pend:1;
+		uint64_t fidx:1;
+		uint64_t index:1;
+		uint64_t nbt:4;
+		uint64_t nbr:3;
+		uint64_t cam:1;
+		uint64_t reserved_12_15:4;
+		uint64_t pp:10;
+		uint64_t reserved_26_63:38;
+#endif
+	} cn66xx;
+};
+
+union cvmx_pow_ds_pc {
+	uint64_t u64;
+	struct cvmx_pow_ds_pc_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t ds_pc:32;
+#else
+		uint64_t ds_pc:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_pow_ecc_err {
+	uint64_t u64;
+	struct cvmx_pow_ecc_err_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_45_63:19;
+		uint64_t iop_ie:13;
+		uint64_t reserved_29_31:3;
+		uint64_t iop:13;
+		uint64_t reserved_14_15:2;
+		uint64_t rpe_ie:1;
+		uint64_t rpe:1;
+		uint64_t reserved_9_11:3;
+		uint64_t syn:5;
+		uint64_t dbe_ie:1;
+		uint64_t sbe_ie:1;
+		uint64_t dbe:1;
+		uint64_t sbe:1;
+#else
+		uint64_t sbe:1;
+		uint64_t dbe:1;
+		uint64_t sbe_ie:1;
+		uint64_t dbe_ie:1;
+		uint64_t syn:5;
+		uint64_t reserved_9_11:3;
+		uint64_t rpe:1;
+		uint64_t rpe_ie:1;
+		uint64_t reserved_14_15:2;
+		uint64_t iop:13;
+		uint64_t reserved_29_31:3;
+		uint64_t iop_ie:13;
+		uint64_t reserved_45_63:19;
+#endif
+	} s;
+	struct cvmx_pow_ecc_err_cn31xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_14_63:50;
+		uint64_t rpe_ie:1;
+		uint64_t rpe:1;
+		uint64_t reserved_9_11:3;
+		uint64_t syn:5;
+		uint64_t dbe_ie:1;
+		uint64_t sbe_ie:1;
+		uint64_t dbe:1;
+		uint64_t sbe:1;
+#else
+		uint64_t sbe:1;
+		uint64_t dbe:1;
+		uint64_t sbe_ie:1;
+		uint64_t dbe_ie:1;
+		uint64_t syn:5;
+		uint64_t reserved_9_11:3;
+		uint64_t rpe:1;
+		uint64_t rpe_ie:1;
+		uint64_t reserved_14_63:50;
+#endif
+	} cn31xx;
+};
+
+union cvmx_pow_int_ctl {
+	uint64_t u64;
+	struct cvmx_pow_int_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t pfr_dis:1;
+		uint64_t nbr_thr:5;
+#else
+		uint64_t nbr_thr:5;
+		uint64_t pfr_dis:1;
+		uint64_t reserved_6_63:58;
+#endif
+	} s;
+};
+
+union cvmx_pow_iq_cntx {
+	uint64_t u64;
+	struct cvmx_pow_iq_cntx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t iq_cnt:32;
+#else
+		uint64_t iq_cnt:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_pow_iq_com_cnt {
+	uint64_t u64;
+	struct cvmx_pow_iq_com_cnt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t iq_cnt:32;
+#else
+		uint64_t iq_cnt:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_pow_iq_int {
+	uint64_t u64;
+	struct cvmx_pow_iq_int_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t iq_int:8;
+#else
+		uint64_t iq_int:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_pow_iq_int_en {
+	uint64_t u64;
+	struct cvmx_pow_iq_int_en_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t int_en:8;
+#else
+		uint64_t int_en:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_pow_iq_thrx {
+	uint64_t u64;
+	struct cvmx_pow_iq_thrx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t iq_thr:32;
+#else
+		uint64_t iq_thr:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_pow_nos_cnt {
+	uint64_t u64;
+	struct cvmx_pow_nos_cnt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t nos_cnt:12;
+#else
+		uint64_t nos_cnt:12;
+		uint64_t reserved_12_63:52;
+#endif
+	} s;
+	struct cvmx_pow_nos_cnt_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t nos_cnt:7;
+#else
+		uint64_t nos_cnt:7;
+		uint64_t reserved_7_63:57;
+#endif
+	} cn30xx;
+	struct cvmx_pow_nos_cnt_cn31xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_9_63:55;
+		uint64_t nos_cnt:9;
+#else
+		uint64_t nos_cnt:9;
+		uint64_t reserved_9_63:55;
+#endif
+	} cn31xx;
+	struct cvmx_pow_nos_cnt_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t nos_cnt:10;
+#else
+		uint64_t nos_cnt:10;
+		uint64_t reserved_10_63:54;
+#endif
+	} cn52xx;
+	struct cvmx_pow_nos_cnt_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_11_63:53;
+		uint64_t nos_cnt:11;
+#else
+		uint64_t nos_cnt:11;
+		uint64_t reserved_11_63:53;
+#endif
+	} cn63xx;
+};
+
+union cvmx_pow_nw_tim {
+	uint64_t u64;
+	struct cvmx_pow_nw_tim_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t nw_tim:10;
+#else
+		uint64_t nw_tim:10;
+		uint64_t reserved_10_63:54;
+#endif
+	} s;
+};
+
+union cvmx_pow_pf_rst_msk {
+	uint64_t u64;
+	struct cvmx_pow_pf_rst_msk_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t rst_msk:8;
+#else
+		uint64_t rst_msk:8;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_pow_pp_grp_mskx {
+	uint64_t u64;
+	struct cvmx_pow_pp_grp_mskx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t qos7_pri:4;
+		uint64_t qos6_pri:4;
+		uint64_t qos5_pri:4;
+		uint64_t qos4_pri:4;
+		uint64_t qos3_pri:4;
+		uint64_t qos2_pri:4;
+		uint64_t qos1_pri:4;
+		uint64_t qos0_pri:4;
+		uint64_t grp_msk:16;
+#else
+		uint64_t grp_msk:16;
+		uint64_t qos0_pri:4;
+		uint64_t qos1_pri:4;
+		uint64_t qos2_pri:4;
+		uint64_t qos3_pri:4;
+		uint64_t qos4_pri:4;
+		uint64_t qos5_pri:4;
+		uint64_t qos6_pri:4;
+		uint64_t qos7_pri:4;
+		uint64_t reserved_48_63:16;
+#endif
+	} s;
+	struct cvmx_pow_pp_grp_mskx_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t grp_msk:16;
+#else
+		uint64_t grp_msk:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} cn30xx;
+};
+
+union cvmx_pow_qos_rndx {
+	uint64_t u64;
+	struct cvmx_pow_qos_rndx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t rnd_p3:8;
+		uint64_t rnd_p2:8;
+		uint64_t rnd_p1:8;
+		uint64_t rnd:8;
+#else
+		uint64_t rnd:8;
+		uint64_t rnd_p1:8;
+		uint64_t rnd_p2:8;
+		uint64_t rnd_p3:8;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_pow_qos_thrx {
+	uint64_t u64;
+	struct cvmx_pow_qos_thrx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_60_63:4;
+		uint64_t des_cnt:12;
+		uint64_t buf_cnt:12;
+		uint64_t free_cnt:12;
+		uint64_t reserved_23_23:1;
+		uint64_t max_thr:11;
+		uint64_t reserved_11_11:1;
+		uint64_t min_thr:11;
+#else
+		uint64_t min_thr:11;
+		uint64_t reserved_11_11:1;
+		uint64_t max_thr:11;
+		uint64_t reserved_23_23:1;
+		uint64_t free_cnt:12;
+		uint64_t buf_cnt:12;
+		uint64_t des_cnt:12;
+		uint64_t reserved_60_63:4;
+#endif
+	} s;
+	struct cvmx_pow_qos_thrx_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_55_63:9;
+		uint64_t des_cnt:7;
+		uint64_t reserved_43_47:5;
+		uint64_t buf_cnt:7;
+		uint64_t reserved_31_35:5;
+		uint64_t free_cnt:7;
+		uint64_t reserved_18_23:6;
+		uint64_t max_thr:6;
+		uint64_t reserved_6_11:6;
+		uint64_t min_thr:6;
+#else
+		uint64_t min_thr:6;
+		uint64_t reserved_6_11:6;
+		uint64_t max_thr:6;
+		uint64_t reserved_18_23:6;
+		uint64_t free_cnt:7;
+		uint64_t reserved_31_35:5;
+		uint64_t buf_cnt:7;
+		uint64_t reserved_43_47:5;
+		uint64_t des_cnt:7;
+		uint64_t reserved_55_63:9;
+#endif
+	} cn30xx;
+	struct cvmx_pow_qos_thrx_cn31xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_57_63:7;
+		uint64_t des_cnt:9;
+		uint64_t reserved_45_47:3;
+		uint64_t buf_cnt:9;
+		uint64_t reserved_33_35:3;
+		uint64_t free_cnt:9;
+		uint64_t reserved_20_23:4;
+		uint64_t max_thr:8;
+		uint64_t reserved_8_11:4;
+		uint64_t min_thr:8;
+#else
+		uint64_t min_thr:8;
+		uint64_t reserved_8_11:4;
+		uint64_t max_thr:8;
+		uint64_t reserved_20_23:4;
+		uint64_t free_cnt:9;
+		uint64_t reserved_33_35:3;
+		uint64_t buf_cnt:9;
+		uint64_t reserved_45_47:3;
+		uint64_t des_cnt:9;
+		uint64_t reserved_57_63:7;
+#endif
+	} cn31xx;
+	struct cvmx_pow_qos_thrx_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_58_63:6;
+		uint64_t des_cnt:10;
+		uint64_t reserved_46_47:2;
+		uint64_t buf_cnt:10;
+		uint64_t reserved_34_35:2;
+		uint64_t free_cnt:10;
+		uint64_t reserved_21_23:3;
+		uint64_t max_thr:9;
+		uint64_t reserved_9_11:3;
+		uint64_t min_thr:9;
+#else
+		uint64_t min_thr:9;
+		uint64_t reserved_9_11:3;
+		uint64_t max_thr:9;
+		uint64_t reserved_21_23:3;
+		uint64_t free_cnt:10;
+		uint64_t reserved_34_35:2;
+		uint64_t buf_cnt:10;
+		uint64_t reserved_46_47:2;
+		uint64_t des_cnt:10;
+		uint64_t reserved_58_63:6;
+#endif
+	} cn52xx;
+	struct cvmx_pow_qos_thrx_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_59_63:5;
+		uint64_t des_cnt:11;
+		uint64_t reserved_47_47:1;
+		uint64_t buf_cnt:11;
+		uint64_t reserved_35_35:1;
+		uint64_t free_cnt:11;
+		uint64_t reserved_22_23:2;
+		uint64_t max_thr:10;
+		uint64_t reserved_10_11:2;
+		uint64_t min_thr:10;
+#else
+		uint64_t min_thr:10;
+		uint64_t reserved_10_11:2;
+		uint64_t max_thr:10;
+		uint64_t reserved_22_23:2;
+		uint64_t free_cnt:11;
+		uint64_t reserved_35_35:1;
+		uint64_t buf_cnt:11;
+		uint64_t reserved_47_47:1;
+		uint64_t des_cnt:11;
+		uint64_t reserved_59_63:5;
+#endif
+	} cn63xx;
+};
+
+union cvmx_pow_ts_pc {
+	uint64_t u64;
+	struct cvmx_pow_ts_pc_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t ts_pc:32;
+#else
+		uint64_t ts_pc:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_pow_wa_com_pc {
+	uint64_t u64;
+	struct cvmx_pow_wa_com_pc_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t wa_pc:32;
+#else
+		uint64_t wa_pc:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_pow_wa_pcx {
+	uint64_t u64;
+	struct cvmx_pow_wa_pcx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t wa_pc:32;
+#else
+		uint64_t wa_pc:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_pow_wq_int {
+	uint64_t u64;
+	struct cvmx_pow_wq_int_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t iq_dis:16;
+		uint64_t wq_int:16;
+#else
+		uint64_t wq_int:16;
+		uint64_t iq_dis:16;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_pow_wq_int_cntx {
+	uint64_t u64;
+	struct cvmx_pow_wq_int_cntx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_28_63:36;
+		uint64_t tc_cnt:4;
+		uint64_t ds_cnt:12;
+		uint64_t iq_cnt:12;
+#else
+		uint64_t iq_cnt:12;
+		uint64_t ds_cnt:12;
+		uint64_t tc_cnt:4;
+		uint64_t reserved_28_63:36;
+#endif
+	} s;
+	struct cvmx_pow_wq_int_cntx_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_28_63:36;
+		uint64_t tc_cnt:4;
+		uint64_t reserved_19_23:5;
+		uint64_t ds_cnt:7;
+		uint64_t reserved_7_11:5;
+		uint64_t iq_cnt:7;
+#else
+		uint64_t iq_cnt:7;
+		uint64_t reserved_7_11:5;
+		uint64_t ds_cnt:7;
+		uint64_t reserved_19_23:5;
+		uint64_t tc_cnt:4;
+		uint64_t reserved_28_63:36;
+#endif
+	} cn30xx;
+	struct cvmx_pow_wq_int_cntx_cn31xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_28_63:36;
+		uint64_t tc_cnt:4;
+		uint64_t reserved_21_23:3;
+		uint64_t ds_cnt:9;
+		uint64_t reserved_9_11:3;
+		uint64_t iq_cnt:9;
+#else
+		uint64_t iq_cnt:9;
+		uint64_t reserved_9_11:3;
+		uint64_t ds_cnt:9;
+		uint64_t reserved_21_23:3;
+		uint64_t tc_cnt:4;
+		uint64_t reserved_28_63:36;
+#endif
+	} cn31xx;
+	struct cvmx_pow_wq_int_cntx_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_28_63:36;
+		uint64_t tc_cnt:4;
+		uint64_t reserved_22_23:2;
+		uint64_t ds_cnt:10;
+		uint64_t reserved_10_11:2;
+		uint64_t iq_cnt:10;
+#else
+		uint64_t iq_cnt:10;
+		uint64_t reserved_10_11:2;
+		uint64_t ds_cnt:10;
+		uint64_t reserved_22_23:2;
+		uint64_t tc_cnt:4;
+		uint64_t reserved_28_63:36;
+#endif
+	} cn52xx;
+	struct cvmx_pow_wq_int_cntx_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_28_63:36;
+		uint64_t tc_cnt:4;
+		uint64_t reserved_23_23:1;
+		uint64_t ds_cnt:11;
+		uint64_t reserved_11_11:1;
+		uint64_t iq_cnt:11;
+#else
+		uint64_t iq_cnt:11;
+		uint64_t reserved_11_11:1;
+		uint64_t ds_cnt:11;
+		uint64_t reserved_23_23:1;
+		uint64_t tc_cnt:4;
+		uint64_t reserved_28_63:36;
+#endif
+	} cn63xx;
+};
+
+union cvmx_pow_wq_int_pc {
+	uint64_t u64;
+	struct cvmx_pow_wq_int_pc_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_60_63:4;
+		uint64_t pc:28;
+		uint64_t reserved_28_31:4;
+		uint64_t pc_thr:20;
+		uint64_t reserved_0_7:8;
+#else
+		uint64_t reserved_0_7:8;
+		uint64_t pc_thr:20;
+		uint64_t reserved_28_31:4;
+		uint64_t pc:28;
+		uint64_t reserved_60_63:4;
+#endif
+	} s;
+};
+
+union cvmx_pow_wq_int_thrx {
+	uint64_t u64;
+	struct cvmx_pow_wq_int_thrx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t tc_en:1;
+		uint64_t tc_thr:4;
+		uint64_t reserved_23_23:1;
+		uint64_t ds_thr:11;
+		uint64_t reserved_11_11:1;
+		uint64_t iq_thr:11;
+#else
+		uint64_t iq_thr:11;
+		uint64_t reserved_11_11:1;
+		uint64_t ds_thr:11;
+		uint64_t reserved_23_23:1;
+		uint64_t tc_thr:4;
+		uint64_t tc_en:1;
+		uint64_t reserved_29_63:35;
+#endif
+	} s;
+	struct cvmx_pow_wq_int_thrx_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t tc_en:1;
+		uint64_t tc_thr:4;
+		uint64_t reserved_18_23:6;
+		uint64_t ds_thr:6;
+		uint64_t reserved_6_11:6;
+		uint64_t iq_thr:6;
+#else
+		uint64_t iq_thr:6;
+		uint64_t reserved_6_11:6;
+		uint64_t ds_thr:6;
+		uint64_t reserved_18_23:6;
+		uint64_t tc_thr:4;
+		uint64_t tc_en:1;
+		uint64_t reserved_29_63:35;
+#endif
+	} cn30xx;
+	struct cvmx_pow_wq_int_thrx_cn31xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t tc_en:1;
+		uint64_t tc_thr:4;
+		uint64_t reserved_20_23:4;
+		uint64_t ds_thr:8;
+		uint64_t reserved_8_11:4;
+		uint64_t iq_thr:8;
+#else
+		uint64_t iq_thr:8;
+		uint64_t reserved_8_11:4;
+		uint64_t ds_thr:8;
+		uint64_t reserved_20_23:4;
+		uint64_t tc_thr:4;
+		uint64_t tc_en:1;
+		uint64_t reserved_29_63:35;
+#endif
+	} cn31xx;
+	struct cvmx_pow_wq_int_thrx_cn52xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t tc_en:1;
+		uint64_t tc_thr:4;
+		uint64_t reserved_21_23:3;
+		uint64_t ds_thr:9;
+		uint64_t reserved_9_11:3;
+		uint64_t iq_thr:9;
+#else
+		uint64_t iq_thr:9;
+		uint64_t reserved_9_11:3;
+		uint64_t ds_thr:9;
+		uint64_t reserved_21_23:3;
+		uint64_t tc_thr:4;
+		uint64_t tc_en:1;
+		uint64_t reserved_29_63:35;
+#endif
+	} cn52xx;
+	struct cvmx_pow_wq_int_thrx_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_29_63:35;
+		uint64_t tc_en:1;
+		uint64_t tc_thr:4;
+		uint64_t reserved_22_23:2;
+		uint64_t ds_thr:10;
+		uint64_t reserved_10_11:2;
+		uint64_t iq_thr:10;
+#else
+		uint64_t iq_thr:10;
+		uint64_t reserved_10_11:2;
+		uint64_t ds_thr:10;
+		uint64_t reserved_22_23:2;
+		uint64_t tc_thr:4;
+		uint64_t tc_en:1;
+		uint64_t reserved_29_63:35;
+#endif
+	} cn63xx;
+};
+
+union cvmx_pow_ws_pcx {
+	uint64_t u64;
+	struct cvmx_pow_ws_pcx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t ws_pc:32;
+#else
+		uint64_t ws_pc:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_sso_wq_int_thrx {
+	uint64_t u64;
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_33_63:31;
+		uint64_t tc_en:1;
+		uint64_t tc_thr:4;
+		uint64_t reserved_26_27:2;
+		uint64_t ds_thr:12;
+		uint64_t reserved_12_13:2;
+		uint64_t iq_thr:12;
+#else
+		uint64_t iq_thr:12;
+		uint64_t reserved_12_13:2;
+		uint64_t ds_thr:12;
+		uint64_t reserved_26_27:2;
+		uint64_t tc_thr:4;
+		uint64_t tc_en:1;
+		uint64_t reserved_33_63:31;
+#endif
+	} s;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-pow.h b/arch/mips/include/asm/octeon/cvmx-pow.h
new file mode 100644
index 000000000..a3b23811e
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-pow.h
@@ -0,0 +1,2215 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/**
+ * Interface to the hardware Packet Order / Work unit.
+ *
+ * New, starting with SDK 1.7.0, cvmx-pow supports a number of
+ * extended consistency checks. The define
+ * CVMX_ENABLE_POW_CHECKS controls the runtime insertion of POW
+ * internal state checks to find common programming errors. If
+ * CVMX_ENABLE_POW_CHECKS is not defined, checks are by default
+ * enabled. For example, cvmx-pow will check for the following
+ * program errors or POW state inconsistency.
+ * - Requesting a POW operation with an active tag switch in
+ *   progress.
+ * - Waiting for a tag switch to complete for an excessively
+ *   long period. This is normally a sign of an error in locking
+ *   causing deadlock.
+ * - Illegal tag switches from NULL_NULL.
+ * - Illegal tag switches from NULL.
+ * - Illegal deschedule request.
+ * - WQE pointer not matching the one attached to the core by
+ *   the POW.
+ *
+ */
+
+#ifndef __CVMX_POW_H__
+#define __CVMX_POW_H__
+
+#include <asm/octeon/cvmx-pow-defs.h>
+
+#include <asm/octeon/cvmx-scratch.h>
+#include <asm/octeon/cvmx-wqe.h>
+
+/* Default to having all POW constancy checks turned on */
+#ifndef CVMX_ENABLE_POW_CHECKS
+#define CVMX_ENABLE_POW_CHECKS 1
+#endif
+
+enum cvmx_pow_tag_type {
+	/* Tag ordering is maintained */
+	CVMX_POW_TAG_TYPE_ORDERED   = 0L,
+	/* Tag ordering is maintained, and at most one PP has the tag */
+	CVMX_POW_TAG_TYPE_ATOMIC    = 1L,
+	/*
+	 * The work queue entry from the order - NEVER tag switch from
+	 * NULL to NULL
+	 */
+	CVMX_POW_TAG_TYPE_NULL	    = 2L,
+	/* A tag switch to NULL, and there is no space reserved in POW
+	 * - NEVER tag switch to NULL_NULL
+	 * - NEVER tag switch from NULL_NULL
+	 * - NULL_NULL is entered at the beginning of time and on a deschedule.
+	 * - NULL_NULL can be exited by a new work request. A NULL_SWITCH
+	 * load can also switch the state to NULL
+	 */
+	CVMX_POW_TAG_TYPE_NULL_NULL = 3L
+};
+
+/**
+ * Wait flag values for pow functions.
+ */
+typedef enum {
+	CVMX_POW_WAIT = 1,
+	CVMX_POW_NO_WAIT = 0,
+} cvmx_pow_wait_t;
+
+/**
+ *  POW tag operations.	 These are used in the data stored to the POW.
+ */
+typedef enum {
+	/*
+	 * switch the tag (only) for this PP
+	 * - the previous tag should be non-NULL in this case
+	 * - tag switch response required
+	 * - fields used: op, type, tag
+	 */
+	CVMX_POW_TAG_OP_SWTAG = 0L,
+	/*
+	 * switch the tag for this PP, with full information
+	 * - this should be used when the previous tag is NULL
+	 * - tag switch response required
+	 * - fields used: address, op, grp, type, tag
+	 */
+	CVMX_POW_TAG_OP_SWTAG_FULL = 1L,
+	/*
+	 * switch the tag (and/or group) for this PP and de-schedule
+	 * - OK to keep the tag the same and only change the group
+	 * - fields used: op, no_sched, grp, type, tag
+	 */
+	CVMX_POW_TAG_OP_SWTAG_DESCH = 2L,
+	/*
+	 * just de-schedule
+	 * - fields used: op, no_sched
+	 */
+	CVMX_POW_TAG_OP_DESCH = 3L,
+	/*
+	 * create an entirely new work queue entry
+	 * - fields used: address, op, qos, grp, type, tag
+	 */
+	CVMX_POW_TAG_OP_ADDWQ = 4L,
+	/*
+	 * just update the work queue pointer and grp for this PP
+	 * - fields used: address, op, grp
+	 */
+	CVMX_POW_TAG_OP_UPDATE_WQP_GRP = 5L,
+	/*
+	 * set the no_sched bit on the de-schedule list
+	 *
+	 * - does nothing if the selected entry is not on the
+	 *   de-schedule list
+	 *
+	 * - does nothing if the stored work queue pointer does not
+	 *   match the address field
+	 *
+	 * - fields used: address, index, op
+	 *
+	 *  Before issuing a *_NSCHED operation, SW must guarantee
+	 *  that all prior deschedules and set/clr NSCHED operations
+	 *  are complete and all prior switches are complete. The
+	 *  hardware provides the opsdone bit and swdone bit for SW
+	 *  polling. After issuing a *_NSCHED operation, SW must
+	 *  guarantee that the set/clr NSCHED is complete before any
+	 *  subsequent operations.
+	 */
+	CVMX_POW_TAG_OP_SET_NSCHED = 6L,
+	/*
+	 * clears the no_sched bit on the de-schedule list
+	 *
+	 * - does nothing if the selected entry is not on the
+	 *   de-schedule list
+	 *
+	 * - does nothing if the stored work queue pointer does not
+	 *   match the address field
+	 *
+	 * - fields used: address, index, op
+	 *
+	 * Before issuing a *_NSCHED operation, SW must guarantee that
+	 * all prior deschedules and set/clr NSCHED operations are
+	 * complete and all prior switches are complete. The hardware
+	 * provides the opsdone bit and swdone bit for SW
+	 * polling. After issuing a *_NSCHED operation, SW must
+	 * guarantee that the set/clr NSCHED is complete before any
+	 * subsequent operations.
+	 */
+	CVMX_POW_TAG_OP_CLR_NSCHED = 7L,
+	/* do nothing */
+	CVMX_POW_TAG_OP_NOP = 15L
+} cvmx_pow_tag_op_t;
+
+/**
+ * This structure defines the store data on a store to POW
+ */
+typedef union {
+	uint64_t u64;
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		/*
+		 * Don't reschedule this entry. no_sched is used for
+		 * CVMX_POW_TAG_OP_SWTAG_DESCH and
+		 * CVMX_POW_TAG_OP_DESCH
+		 */
+		uint64_t no_sched:1;
+		uint64_t unused:2;
+		/* Tontains index of entry for a CVMX_POW_TAG_OP_*_NSCHED */
+		uint64_t index:13;
+		/* The operation to perform */
+		cvmx_pow_tag_op_t op:4;
+		uint64_t unused2:2;
+		/*
+		 * The QOS level for the packet. qos is only used for
+		 * CVMX_POW_TAG_OP_ADDWQ
+		 */
+		uint64_t qos:3;
+		/*
+		 * The group that the work queue entry will be
+		 * scheduled to grp is used for CVMX_POW_TAG_OP_ADDWQ,
+		 * CVMX_POW_TAG_OP_SWTAG_FULL,
+		 * CVMX_POW_TAG_OP_SWTAG_DESCH, and
+		 * CVMX_POW_TAG_OP_UPDATE_WQP_GRP
+		 */
+		uint64_t grp:4;
+		/*
+		 * The type of the tag. type is used for everything
+		 * except CVMX_POW_TAG_OP_DESCH,
+		 * CVMX_POW_TAG_OP_UPDATE_WQP_GRP, and
+		 * CVMX_POW_TAG_OP_*_NSCHED
+		 */
+		uint64_t type:3;
+		/*
+		 * The actual tag. tag is used for everything except
+		 * CVMX_POW_TAG_OP_DESCH,
+		 * CVMX_POW_TAG_OP_UPDATE_WQP_GRP, and
+		 * CVMX_POW_TAG_OP_*_NSCHED
+		 */
+		uint64_t tag:32;
+#else
+		uint64_t tag:32;
+		uint64_t type:3;
+		uint64_t grp:4;
+		uint64_t qos:3;
+		uint64_t unused2:2;
+		cvmx_pow_tag_op_t op:4;
+		uint64_t index:13;
+		uint64_t unused:2;
+		uint64_t no_sched:1;
+#endif
+	} s;
+} cvmx_pow_tag_req_t;
+
+/**
+ * This structure describes the address to load stuff from POW
+ */
+typedef union {
+	uint64_t u64;
+
+    /**
+     * Address for new work request loads (did<2:0> == 0)
+     */
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		/* Mips64 address region. Should be CVMX_IO_SEG */
+		uint64_t mem_region:2;
+		/* Must be zero */
+		uint64_t reserved_49_61:13;
+		/* Must be one */
+		uint64_t is_io:1;
+		/* the ID of POW -- did<2:0> == 0 in this case */
+		uint64_t did:8;
+		/* Must be zero */
+		uint64_t reserved_4_39:36;
+		/*
+		 * If set, don't return load response until work is
+		 * available.
+		 */
+		uint64_t wait:1;
+		/* Must be zero */
+		uint64_t reserved_0_2:3;
+#else
+		uint64_t reserved_0_2:3;
+		uint64_t wait:1;
+		uint64_t reserved_4_39:36;
+		uint64_t did:8;
+		uint64_t is_io:1;
+		uint64_t reserved_49_61:13;
+		uint64_t mem_region:2;
+#endif
+	} swork;
+
+    /**
+     * Address for loads to get POW internal status
+     */
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		/* Mips64 address region. Should be CVMX_IO_SEG */
+		uint64_t mem_region:2;
+		/* Must be zero */
+		uint64_t reserved_49_61:13;
+		/* Must be one */
+		uint64_t is_io:1;
+		/* the ID of POW -- did<2:0> == 1 in this case */
+		uint64_t did:8;
+		/* Must be zero */
+		uint64_t reserved_10_39:30;
+		/* The core id to get status for */
+		uint64_t coreid:4;
+		/*
+		 * If set and get_cur is set, return reverse tag-list
+		 * pointer rather than forward tag-list pointer.
+		 */
+		uint64_t get_rev:1;
+		/*
+		 * If set, return current status rather than pending
+		 * status.
+		 */
+		uint64_t get_cur:1;
+		/*
+		 * If set, get the work-queue pointer rather than
+		 * tag/type.
+		 */
+		uint64_t get_wqp:1;
+		/* Must be zero */
+		uint64_t reserved_0_2:3;
+#else
+		uint64_t reserved_0_2:3;
+		uint64_t get_wqp:1;
+		uint64_t get_cur:1;
+		uint64_t get_rev:1;
+		uint64_t coreid:4;
+		uint64_t reserved_10_39:30;
+		uint64_t did:8;
+		uint64_t is_io:1;
+		uint64_t reserved_49_61:13;
+		uint64_t mem_region:2;
+#endif
+	} sstatus;
+
+    /**
+     * Address for memory loads to get POW internal state
+     */
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		/* Mips64 address region. Should be CVMX_IO_SEG */
+		uint64_t mem_region:2;
+		/* Must be zero */
+		uint64_t reserved_49_61:13;
+		/* Must be one */
+		uint64_t is_io:1;
+		/* the ID of POW -- did<2:0> == 2 in this case */
+		uint64_t did:8;
+		/* Must be zero */
+		uint64_t reserved_16_39:24;
+		/* POW memory index */
+		uint64_t index:11;
+		/*
+		 * If set, return deschedule information rather than
+		 * the standard response for work-queue index (invalid
+		 * if the work-queue entry is not on the deschedule
+		 * list).
+		 */
+		uint64_t get_des:1;
+		/*
+		 * If set, get the work-queue pointer rather than
+		 * tag/type (no effect when get_des set).
+		 */
+		uint64_t get_wqp:1;
+		/* Must be zero */
+		uint64_t reserved_0_2:3;
+#else
+		uint64_t reserved_0_2:3;
+		uint64_t get_wqp:1;
+		uint64_t get_des:1;
+		uint64_t index:11;
+		uint64_t reserved_16_39:24;
+		uint64_t did:8;
+		uint64_t is_io:1;
+		uint64_t reserved_49_61:13;
+		uint64_t mem_region:2;
+#endif
+	} smemload;
+
+    /**
+     * Address for index/pointer loads
+     */
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		/* Mips64 address region. Should be CVMX_IO_SEG */
+		uint64_t mem_region:2;
+		/* Must be zero */
+		uint64_t reserved_49_61:13;
+		/* Must be one */
+		uint64_t is_io:1;
+		/* the ID of POW -- did<2:0> == 3 in this case */
+		uint64_t did:8;
+		/* Must be zero */
+		uint64_t reserved_9_39:31;
+		/*
+		 * when {get_rmt ==0 AND get_des_get_tail == 0}, this
+		 * field selects one of eight POW internal-input
+		 * queues (0-7), one per QOS level; values 8-15 are
+		 * illegal in this case; when {get_rmt ==0 AND
+		 * get_des_get_tail == 1}, this field selects one of
+		 * 16 deschedule lists (per group); when get_rmt ==1,
+		 * this field selects one of 16 memory-input queue
+		 * lists.  The two memory-input queue lists associated
+		 * with each QOS level are:
+		 *
+		 * - qosgrp = 0, qosgrp = 8:	  QOS0
+		 * - qosgrp = 1, qosgrp = 9:	  QOS1
+		 * - qosgrp = 2, qosgrp = 10:	  QOS2
+		 * - qosgrp = 3, qosgrp = 11:	  QOS3
+		 * - qosgrp = 4, qosgrp = 12:	  QOS4
+		 * - qosgrp = 5, qosgrp = 13:	  QOS5
+		 * - qosgrp = 6, qosgrp = 14:	  QOS6
+		 * - qosgrp = 7, qosgrp = 15:	  QOS7
+		 */
+		uint64_t qosgrp:4;
+		/*
+		 * If set and get_rmt is clear, return deschedule list
+		 * indexes rather than indexes for the specified qos
+		 * level; if set and get_rmt is set, return the tail
+		 * pointer rather than the head pointer for the
+		 * specified qos level.
+		 */
+		uint64_t get_des_get_tail:1;
+		/*
+		 * If set, return remote pointers rather than the
+		 * local indexes for the specified qos level.
+		 */
+		uint64_t get_rmt:1;
+		/* Must be zero */
+		uint64_t reserved_0_2:3;
+#else
+		uint64_t reserved_0_2:3;
+		uint64_t get_rmt:1;
+		uint64_t get_des_get_tail:1;
+		uint64_t qosgrp:4;
+		uint64_t reserved_9_39:31;
+		uint64_t did:8;
+		uint64_t is_io:1;
+		uint64_t reserved_49_61:13;
+		uint64_t mem_region:2;
+#endif
+	} sindexload;
+
+    /**
+     * address for NULL_RD request (did<2:0> == 4) when this is read,
+     * HW attempts to change the state to NULL if it is NULL_NULL (the
+     * hardware cannot switch from NULL_NULL to NULL if a POW entry is
+     * not available - software may need to recover by finishing
+     * another piece of work before a POW entry can ever become
+     * available.)
+     */
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		/* Mips64 address region. Should be CVMX_IO_SEG */
+		uint64_t mem_region:2;
+		/* Must be zero */
+		uint64_t reserved_49_61:13;
+		/* Must be one */
+		uint64_t is_io:1;
+		/* the ID of POW -- did<2:0> == 4 in this case */
+		uint64_t did:8;
+		/* Must be zero */
+		uint64_t reserved_0_39:40;
+#else
+		uint64_t reserved_0_39:40;
+		uint64_t did:8;
+		uint64_t is_io:1;
+		uint64_t reserved_49_61:13;
+		uint64_t mem_region:2;
+#endif
+	} snull_rd;
+} cvmx_pow_load_addr_t;
+
+/**
+ * This structure defines the response to a load/SENDSINGLE to POW
+ * (except CSR reads)
+ */
+typedef union {
+	uint64_t u64;
+
+    /**
+     * Response to new work request loads
+     */
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		/*
+		 * Set when no new work queue entry was returned.  *
+		 * If there was de-scheduled work, the HW will
+		 * definitely return it. When this bit is set, it
+		 * could mean either mean:
+		 *
+		 * - There was no work, or
+		 *
+		 * - There was no work that the HW could find. This
+		 *   case can happen, regardless of the wait bit value
+		 *   in the original request, when there is work in
+		 *   the IQ's that is too deep down the list.
+		 */
+		uint64_t no_work:1;
+		/* Must be zero */
+		uint64_t reserved_40_62:23;
+		/* 36 in O1 -- the work queue pointer */
+		uint64_t addr:40;
+#else
+		uint64_t addr:40;
+		uint64_t reserved_40_62:23;
+		uint64_t no_work:1;
+#endif
+	} s_work;
+
+    /**
+     * Result for a POW Status Load (when get_cur==0 and get_wqp==0)
+     */
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_62_63:2;
+		/* Set when there is a pending non-NULL SWTAG or
+		 * SWTAG_FULL, and the POW entry has not left the list
+		 * for the original tag. */
+		uint64_t pend_switch:1;
+		/* Set when SWTAG_FULL and pend_switch is set. */
+		uint64_t pend_switch_full:1;
+		/*
+		 * Set when there is a pending NULL SWTAG, or an
+		 * implicit switch to NULL.
+		 */
+		uint64_t pend_switch_null:1;
+		/* Set when there is a pending DESCHED or SWTAG_DESCHED. */
+		uint64_t pend_desched:1;
+		/*
+		 * Set when there is a pending SWTAG_DESCHED and
+		 * pend_desched is set.
+		 */
+		uint64_t pend_desched_switch:1;
+		/* Set when nosched is desired and pend_desched is set. */
+		uint64_t pend_nosched:1;
+		/* Set when there is a pending GET_WORK. */
+		uint64_t pend_new_work:1;
+		/*
+		 * When pend_new_work is set, this bit indicates that
+		 * the wait bit was set.
+		 */
+		uint64_t pend_new_work_wait:1;
+		/* Set when there is a pending NULL_RD. */
+		uint64_t pend_null_rd:1;
+		/* Set when there is a pending CLR_NSCHED. */
+		uint64_t pend_nosched_clr:1;
+		uint64_t reserved_51:1;
+		/* This is the index when pend_nosched_clr is set. */
+		uint64_t pend_index:11;
+		/*
+		 * This is the new_grp when (pend_desched AND
+		 * pend_desched_switch) is set.
+		 */
+		uint64_t pend_grp:4;
+		uint64_t reserved_34_35:2;
+		/*
+		 * This is the tag type when pend_switch or
+		 * (pend_desched AND pend_desched_switch) are set.
+		 */
+		uint64_t pend_type:2;
+		/*
+		 * - this is the tag when pend_switch or (pend_desched
+		 *    AND pend_desched_switch) are set.
+		 */
+		uint64_t pend_tag:32;
+#else
+		uint64_t pend_tag:32;
+		uint64_t pend_type:2;
+		uint64_t reserved_34_35:2;
+		uint64_t pend_grp:4;
+		uint64_t pend_index:11;
+		uint64_t reserved_51:1;
+		uint64_t pend_nosched_clr:1;
+		uint64_t pend_null_rd:1;
+		uint64_t pend_new_work_wait:1;
+		uint64_t pend_new_work:1;
+		uint64_t pend_nosched:1;
+		uint64_t pend_desched_switch:1;
+		uint64_t pend_desched:1;
+		uint64_t pend_switch_null:1;
+		uint64_t pend_switch_full:1;
+		uint64_t pend_switch:1;
+		uint64_t reserved_62_63:2;
+#endif
+	} s_sstatus0;
+
+    /**
+     * Result for a POW Status Load (when get_cur==0 and get_wqp==1)
+     */
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_62_63:2;
+		/*
+		 * Set when there is a pending non-NULL SWTAG or
+		 * SWTAG_FULL, and the POW entry has not left the list
+		 * for the original tag.
+		 */
+		uint64_t pend_switch:1;
+		/* Set when SWTAG_FULL and pend_switch is set. */
+		uint64_t pend_switch_full:1;
+		/*
+		 * Set when there is a pending NULL SWTAG, or an
+		 * implicit switch to NULL.
+		 */
+		uint64_t pend_switch_null:1;
+		/*
+		 * Set when there is a pending DESCHED or
+		 * SWTAG_DESCHED.
+		 */
+		uint64_t pend_desched:1;
+		/*
+		 * Set when there is a pending SWTAG_DESCHED and
+		 * pend_desched is set.
+		 */
+		uint64_t pend_desched_switch:1;
+		/* Set when nosched is desired and pend_desched is set. */
+		uint64_t pend_nosched:1;
+		/* Set when there is a pending GET_WORK. */
+		uint64_t pend_new_work:1;
+		/*
+		 * When pend_new_work is set, this bit indicates that
+		 * the wait bit was set.
+		 */
+		uint64_t pend_new_work_wait:1;
+		/* Set when there is a pending NULL_RD. */
+		uint64_t pend_null_rd:1;
+		/* Set when there is a pending CLR_NSCHED. */
+		uint64_t pend_nosched_clr:1;
+		uint64_t reserved_51:1;
+		/* This is the index when pend_nosched_clr is set. */
+		uint64_t pend_index:11;
+		/*
+		 * This is the new_grp when (pend_desched AND
+		 * pend_desched_switch) is set.
+		 */
+		uint64_t pend_grp:4;
+		/* This is the wqp when pend_nosched_clr is set. */
+		uint64_t pend_wqp:36;
+#else
+	        uint64_t pend_wqp:36;
+	        uint64_t pend_grp:4;
+	        uint64_t pend_index:11;
+	        uint64_t reserved_51:1;
+	        uint64_t pend_nosched_clr:1;
+	        uint64_t pend_null_rd:1;
+	        uint64_t pend_new_work_wait:1;
+	        uint64_t pend_new_work:1;
+	        uint64_t pend_nosched:1;
+	        uint64_t pend_desched_switch:1;
+	        uint64_t pend_desched:1;
+	        uint64_t pend_switch_null:1;
+	        uint64_t pend_switch_full:1;
+	        uint64_t pend_switch:1;
+	        uint64_t reserved_62_63:2;
+#endif
+	} s_sstatus1;
+
+    /**
+     * Result for a POW Status Load (when get_cur==1, get_wqp==0, and
+     * get_rev==0)
+     */
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_62_63:2;
+		/*
+		 * Points to the next POW entry in the tag list when
+		 * tail == 0 (and tag_type is not NULL or NULL_NULL).
+		 */
+		uint64_t link_index:11;
+		/* The POW entry attached to the core. */
+		uint64_t index:11;
+		/*
+		 * The group attached to the core (updated when new
+		 * tag list entered on SWTAG_FULL).
+		 */
+		uint64_t grp:4;
+		/*
+		 * Set when this POW entry is at the head of its tag
+		 * list (also set when in the NULL or NULL_NULL
+		 * state).
+		 */
+		uint64_t head:1;
+		/*
+		 * Set when this POW entry is at the tail of its tag
+		 * list (also set when in the NULL or NULL_NULL
+		 * state).
+		 */
+		uint64_t tail:1;
+		/*
+		 * The tag type attached to the core (updated when new
+		 * tag list entered on SWTAG, SWTAG_FULL, or
+		 * SWTAG_DESCHED).
+		 */
+		uint64_t tag_type:2;
+		/*
+		 * The tag attached to the core (updated when new tag
+		 * list entered on SWTAG, SWTAG_FULL, or
+		 * SWTAG_DESCHED).
+		 */
+		uint64_t tag:32;
+#else
+	        uint64_t tag:32;
+	        uint64_t tag_type:2;
+	        uint64_t tail:1;
+	        uint64_t head:1;
+	        uint64_t grp:4;
+	        uint64_t index:11;
+	        uint64_t link_index:11;
+	        uint64_t reserved_62_63:2;
+#endif
+	} s_sstatus2;
+
+    /**
+     * Result for a POW Status Load (when get_cur==1, get_wqp==0, and get_rev==1)
+     */
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_62_63:2;
+		/*
+		 * Points to the prior POW entry in the tag list when
+		 * head == 0 (and tag_type is not NULL or
+		 * NULL_NULL). This field is unpredictable when the
+		 * core's state is NULL or NULL_NULL.
+		 */
+		uint64_t revlink_index:11;
+		/* The POW entry attached to the core. */
+		uint64_t index:11;
+		/*
+		 * The group attached to the core (updated when new
+		 * tag list entered on SWTAG_FULL).
+		 */
+		uint64_t grp:4;
+		/* Set when this POW entry is at the head of its tag
+		 * list (also set when in the NULL or NULL_NULL
+		 * state).
+		 */
+		uint64_t head:1;
+		/*
+		 * Set when this POW entry is at the tail of its tag
+		 * list (also set when in the NULL or NULL_NULL
+		 * state).
+		 */
+		uint64_t tail:1;
+		/*
+		 * The tag type attached to the core (updated when new
+		 * tag list entered on SWTAG, SWTAG_FULL, or
+		 * SWTAG_DESCHED).
+		 */
+		uint64_t tag_type:2;
+		/*
+		 * The tag attached to the core (updated when new tag
+		 * list entered on SWTAG, SWTAG_FULL, or
+		 * SWTAG_DESCHED).
+		 */
+		uint64_t tag:32;
+#else
+	        uint64_t tag:32;
+	        uint64_t tag_type:2;
+	        uint64_t tail:1;
+	        uint64_t head:1;
+	        uint64_t grp:4;
+	        uint64_t index:11;
+	        uint64_t revlink_index:11;
+	        uint64_t reserved_62_63:2;
+#endif
+	} s_sstatus3;
+
+    /**
+     * Result for a POW Status Load (when get_cur==1, get_wqp==1, and
+     * get_rev==0)
+     */
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_62_63:2;
+		/*
+		 * Points to the next POW entry in the tag list when
+		 * tail == 0 (and tag_type is not NULL or NULL_NULL).
+		 */
+		uint64_t link_index:11;
+		/* The POW entry attached to the core. */
+		uint64_t index:11;
+		/*
+		 * The group attached to the core (updated when new
+		 * tag list entered on SWTAG_FULL).
+		 */
+		uint64_t grp:4;
+		/*
+		 * The wqp attached to the core (updated when new tag
+		 * list entered on SWTAG_FULL).
+		 */
+		uint64_t wqp:36;
+#else
+	        uint64_t wqp:36;
+	        uint64_t grp:4;
+	        uint64_t index:11;
+	        uint64_t link_index:11;
+	        uint64_t reserved_62_63:2;
+#endif
+	} s_sstatus4;
+
+    /**
+     * Result for a POW Status Load (when get_cur==1, get_wqp==1, and
+     * get_rev==1)
+     */
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_62_63:2;
+		/*
+		 * Points to the prior POW entry in the tag list when
+		 * head == 0 (and tag_type is not NULL or
+		 * NULL_NULL). This field is unpredictable when the
+		 * core's state is NULL or NULL_NULL.
+		 */
+		uint64_t revlink_index:11;
+		/* The POW entry attached to the core. */
+		uint64_t index:11;
+		/*
+		 * The group attached to the core (updated when new
+		 * tag list entered on SWTAG_FULL).
+		 */
+		uint64_t grp:4;
+		/*
+		 * The wqp attached to the core (updated when new tag
+		 * list entered on SWTAG_FULL).
+		 */
+		uint64_t wqp:36;
+#else
+	        uint64_t wqp:36;
+	        uint64_t grp:4;
+	        uint64_t index:11;
+	        uint64_t revlink_index:11;
+	        uint64_t reserved_62_63:2;
+#endif
+	} s_sstatus5;
+
+    /**
+     * Result For POW Memory Load (get_des == 0 and get_wqp == 0)
+     */
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_51_63:13;
+		/*
+		 * The next entry in the input, free, descheduled_head
+		 * list (unpredictable if entry is the tail of the
+		 * list).
+		 */
+		uint64_t next_index:11;
+		/* The group of the POW entry. */
+		uint64_t grp:4;
+		uint64_t reserved_35:1;
+		/*
+		 * Set when this POW entry is at the tail of its tag
+		 * list (also set when in the NULL or NULL_NULL
+		 * state).
+		 */
+		uint64_t tail:1;
+		/* The tag type of the POW entry. */
+		uint64_t tag_type:2;
+		/* The tag of the POW entry. */
+		uint64_t tag:32;
+#else
+	        uint64_t tag:32;
+	        uint64_t tag_type:2;
+	        uint64_t tail:1;
+	        uint64_t reserved_35:1;
+	        uint64_t grp:4;
+	        uint64_t next_index:11;
+	        uint64_t reserved_51_63:13;
+#endif
+	} s_smemload0;
+
+    /**
+     * Result For POW Memory Load (get_des == 0 and get_wqp == 1)
+     */
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_51_63:13;
+		/*
+		 * The next entry in the input, free, descheduled_head
+		 * list (unpredictable if entry is the tail of the
+		 * list).
+		 */
+		uint64_t next_index:11;
+		/* The group of the POW entry. */
+		uint64_t grp:4;
+		/* The WQP held in the POW entry. */
+		uint64_t wqp:36;
+#else
+	        uint64_t wqp:36;
+	        uint64_t grp:4;
+	        uint64_t next_index:11;
+	        uint64_t reserved_51_63:13;
+#endif
+	} s_smemload1;
+
+    /**
+     * Result For POW Memory Load (get_des == 1)
+     */
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_51_63:13;
+		/*
+		 * The next entry in the tag list connected to the
+		 * descheduled head.
+		 */
+		uint64_t fwd_index:11;
+		/* The group of the POW entry. */
+		uint64_t grp:4;
+		/* The nosched bit for the POW entry. */
+		uint64_t nosched:1;
+		/* There is a pending tag switch */
+		uint64_t pend_switch:1;
+		/*
+		 * The next tag type for the new tag list when
+		 * pend_switch is set.
+		 */
+		uint64_t pend_type:2;
+		/*
+		 * The next tag for the new tag list when pend_switch
+		 * is set.
+		 */
+		uint64_t pend_tag:32;
+#else
+	        uint64_t pend_tag:32;
+	        uint64_t pend_type:2;
+	        uint64_t pend_switch:1;
+	        uint64_t nosched:1;
+	        uint64_t grp:4;
+	        uint64_t fwd_index:11;
+	        uint64_t reserved_51_63:13;
+#endif
+	} s_smemload2;
+
+    /**
+     * Result For POW Index/Pointer Load (get_rmt == 0/get_des_get_tail == 0)
+     */
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_52_63:12;
+		/*
+		 * set when there is one or more POW entries on the
+		 * free list.
+		 */
+		uint64_t free_val:1;
+		/*
+		 * set when there is exactly one POW entry on the free
+		 * list.
+		 */
+		uint64_t free_one:1;
+		uint64_t reserved_49:1;
+		/*
+		 * when free_val is set, indicates the first entry on
+		 * the free list.
+		 */
+		uint64_t free_head:11;
+		uint64_t reserved_37:1;
+		/*
+		 * when free_val is set, indicates the last entry on
+		 * the free list.
+		 */
+		uint64_t free_tail:11;
+		/*
+		 * set when there is one or more POW entries on the
+		 * input Q list selected by qosgrp.
+		 */
+		uint64_t loc_val:1;
+		/*
+		 * set when there is exactly one POW entry on the
+		 * input Q list selected by qosgrp.
+		 */
+		uint64_t loc_one:1;
+		uint64_t reserved_23:1;
+		/*
+		 * when loc_val is set, indicates the first entry on
+		 * the input Q list selected by qosgrp.
+		 */
+		uint64_t loc_head:11;
+		uint64_t reserved_11:1;
+		/*
+		 * when loc_val is set, indicates the last entry on
+		 * the input Q list selected by qosgrp.
+		 */
+		uint64_t loc_tail:11;
+#else
+	        uint64_t loc_tail:11;
+	        uint64_t reserved_11:1;
+	        uint64_t loc_head:11;
+	        uint64_t reserved_23:1;
+	        uint64_t loc_one:1;
+	        uint64_t loc_val:1;
+	        uint64_t free_tail:11;
+	        uint64_t reserved_37:1;
+	        uint64_t free_head:11;
+	        uint64_t reserved_49:1;
+	        uint64_t free_one:1;
+	        uint64_t free_val:1;
+	        uint64_t reserved_52_63:12;
+#endif
+	} sindexload0;
+
+    /**
+     * Result For POW Index/Pointer Load (get_rmt == 0/get_des_get_tail == 1)
+     */
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_52_63:12;
+		/*
+		 * set when there is one or more POW entries on the
+		 * nosched list.
+		 */
+		uint64_t nosched_val:1;
+		/*
+		 * set when there is exactly one POW entry on the
+		 * nosched list.
+		 */
+		uint64_t nosched_one:1;
+		uint64_t reserved_49:1;
+		/*
+		 * when nosched_val is set, indicates the first entry
+		 * on the nosched list.
+		 */
+		uint64_t nosched_head:11;
+		uint64_t reserved_37:1;
+		/*
+		 * when nosched_val is set, indicates the last entry
+		 * on the nosched list.
+		 */
+		uint64_t nosched_tail:11;
+		/*
+		 * set when there is one or more descheduled heads on
+		 * the descheduled list selected by qosgrp.
+		 */
+		uint64_t des_val:1;
+		/*
+		 * set when there is exactly one descheduled head on
+		 * the descheduled list selected by qosgrp.
+		 */
+		uint64_t des_one:1;
+		uint64_t reserved_23:1;
+		/*
+		 * when des_val is set, indicates the first
+		 * descheduled head on the descheduled list selected
+		 * by qosgrp.
+		 */
+		uint64_t des_head:11;
+		uint64_t reserved_11:1;
+		/*
+		 * when des_val is set, indicates the last descheduled
+		 * head on the descheduled list selected by qosgrp.
+		 */
+		uint64_t des_tail:11;
+#else
+	        uint64_t des_tail:11;
+	        uint64_t reserved_11:1;
+	        uint64_t des_head:11;
+	        uint64_t reserved_23:1;
+	        uint64_t des_one:1;
+	        uint64_t des_val:1;
+	        uint64_t nosched_tail:11;
+	        uint64_t reserved_37:1;
+	        uint64_t nosched_head:11;
+	        uint64_t reserved_49:1;
+	        uint64_t nosched_one:1;
+	        uint64_t nosched_val:1;
+	        uint64_t reserved_52_63:12;
+#endif
+	} sindexload1;
+
+    /**
+     * Result For POW Index/Pointer Load (get_rmt == 1/get_des_get_tail == 0)
+     */
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_39_63:25;
+		/*
+		 * Set when this DRAM list is the current head
+		 * (i.e. is the next to be reloaded when the POW
+		 * hardware reloads a POW entry from DRAM). The POW
+		 * hardware alternates between the two DRAM lists
+		 * associated with a QOS level when it reloads work
+		 * from DRAM into the POW unit.
+		 */
+		uint64_t rmt_is_head:1;
+		/*
+		 * Set when the DRAM portion of the input Q list
+		 * selected by qosgrp contains one or more pieces of
+		 * work.
+		 */
+		uint64_t rmt_val:1;
+		/*
+		 * Set when the DRAM portion of the input Q list
+		 * selected by qosgrp contains exactly one piece of
+		 * work.
+		 */
+		uint64_t rmt_one:1;
+		/*
+		 * When rmt_val is set, indicates the first piece of
+		 * work on the DRAM input Q list selected by
+		 * qosgrp.
+		 */
+		uint64_t rmt_head:36;
+#else
+	        uint64_t rmt_head:36;
+	        uint64_t rmt_one:1;
+	        uint64_t rmt_val:1;
+	        uint64_t rmt_is_head:1;
+	        uint64_t reserved_39_63:25;
+#endif
+	} sindexload2;
+
+    /**
+     * Result For POW Index/Pointer Load (get_rmt ==
+     * 1/get_des_get_tail == 1)
+     */
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_39_63:25;
+		/*
+		 * set when this DRAM list is the current head
+		 * (i.e. is the next to be reloaded when the POW
+		 * hardware reloads a POW entry from DRAM). The POW
+		 * hardware alternates between the two DRAM lists
+		 * associated with a QOS level when it reloads work
+		 * from DRAM into the POW unit.
+		 */
+		uint64_t rmt_is_head:1;
+		/*
+		 * set when the DRAM portion of the input Q list
+		 * selected by qosgrp contains one or more pieces of
+		 * work.
+		 */
+		uint64_t rmt_val:1;
+		/*
+		 * set when the DRAM portion of the input Q list
+		 * selected by qosgrp contains exactly one piece of
+		 * work.
+		 */
+		uint64_t rmt_one:1;
+		/*
+		 * when rmt_val is set, indicates the last piece of
+		 * work on the DRAM input Q list selected by
+		 * qosgrp.
+		 */
+		uint64_t rmt_tail:36;
+#else
+	        uint64_t rmt_tail:36;
+	        uint64_t rmt_one:1;
+	        uint64_t rmt_val:1;
+	        uint64_t rmt_is_head:1;
+	        uint64_t reserved_39_63:25;
+#endif
+	} sindexload3;
+
+    /**
+     * Response to NULL_RD request loads
+     */
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t unused:62;
+		/* of type cvmx_pow_tag_type_t. state is one of the
+		 * following:
+		 *
+		 * - CVMX_POW_TAG_TYPE_ORDERED
+		 * - CVMX_POW_TAG_TYPE_ATOMIC
+		 * - CVMX_POW_TAG_TYPE_NULL
+		 * - CVMX_POW_TAG_TYPE_NULL_NULL
+		 */
+		uint64_t state:2;
+#else
+	        uint64_t state:2;
+	        uint64_t unused:62;
+#endif
+	} s_null_rd;
+
+} cvmx_pow_tag_load_resp_t;
+
+/**
+ * This structure describes the address used for stores to the POW.
+ *  The store address is meaningful on stores to the POW.  The
+ *  hardware assumes that an aligned 64-bit store was used for all
+ *  these stores.  Note the assumption that the work queue entry is
+ *  aligned on an 8-byte boundary (since the low-order 3 address bits
+ *  must be zero).  Note that not all fields are used by all
+ *  operations.
+ *
+ *  NOTE: The following is the behavior of the pending switch bit at the PP
+ *	 for POW stores (i.e. when did<7:3> == 0xc)
+ *     - did<2:0> == 0	    => pending switch bit is set
+ *     - did<2:0> == 1	    => no affect on the pending switch bit
+ *     - did<2:0> == 3	    => pending switch bit is cleared
+ *     - did<2:0> == 7	    => no affect on the pending switch bit
+ *     - did<2:0> == others => must not be used
+ *     - No other loads/stores have an affect on the pending switch bit
+ *     - The switch bus from POW can clear the pending switch bit
+ *
+ *  NOTE: did<2:0> == 2 is used by the HW for a special single-cycle
+ *  ADDWQ command that only contains the pointer). SW must never use
+ *  did<2:0> == 2.
+ */
+typedef union {
+    /**
+     * Unsigned 64 bit integer representation of store address
+     */
+	uint64_t u64;
+
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		/* Memory region.  Should be CVMX_IO_SEG in most cases */
+		uint64_t mem_reg:2;
+		uint64_t reserved_49_61:13;	/* Must be zero */
+		uint64_t is_io:1;	/* Must be one */
+		/* Device ID of POW.  Note that different sub-dids are used. */
+		uint64_t did:8;
+		uint64_t reserved_36_39:4;	/* Must be zero */
+		/* Address field. addr<2:0> must be zero */
+		uint64_t addr:36;
+#else
+	        uint64_t addr:36;
+	        uint64_t reserved_36_39:4;
+	        uint64_t did:8;
+	        uint64_t is_io:1;
+	        uint64_t reserved_49_61:13;
+	        uint64_t mem_reg:2;
+#endif
+	} stag;
+} cvmx_pow_tag_store_addr_t;
+
+/**
+ * decode of the store data when an IOBDMA SENDSINGLE is sent to POW
+ */
+typedef union {
+	uint64_t u64;
+
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		/*
+		 * the (64-bit word) location in scratchpad to write
+		 * to (if len != 0)
+		 */
+		uint64_t scraddr:8;
+		/* the number of words in the response (0 => no response) */
+		uint64_t len:8;
+		/* the ID of the device on the non-coherent bus */
+		uint64_t did:8;
+		uint64_t unused:36;
+		/* if set, don't return load response until work is available */
+		uint64_t wait:1;
+		uint64_t unused2:3;
+#else
+	        uint64_t unused2:3;
+	        uint64_t wait:1;
+	        uint64_t unused:36;
+	        uint64_t did:8;
+	        uint64_t len:8;
+	        uint64_t scraddr:8;
+#endif
+	} s;
+
+} cvmx_pow_iobdma_store_t;
+
+/* CSR typedefs have been moved to cvmx-csr-*.h */
+
+/**
+ * Get the POW tag for this core. This returns the current
+ * tag type, tag, group, and POW entry index associated with
+ * this core. Index is only valid if the tag type isn't NULL_NULL.
+ * If a tag switch is pending this routine returns the tag before
+ * the tag switch, not after.
+ *
+ * Returns Current tag
+ */
+static inline cvmx_pow_tag_req_t cvmx_pow_get_current_tag(void)
+{
+	cvmx_pow_load_addr_t load_addr;
+	cvmx_pow_tag_load_resp_t load_resp;
+	cvmx_pow_tag_req_t result;
+
+	load_addr.u64 = 0;
+	load_addr.sstatus.mem_region = CVMX_IO_SEG;
+	load_addr.sstatus.is_io = 1;
+	load_addr.sstatus.did = CVMX_OCT_DID_TAG_TAG1;
+	load_addr.sstatus.coreid = cvmx_get_core_num();
+	load_addr.sstatus.get_cur = 1;
+	load_resp.u64 = cvmx_read_csr(load_addr.u64);
+	result.u64 = 0;
+	result.s.grp = load_resp.s_sstatus2.grp;
+	result.s.index = load_resp.s_sstatus2.index;
+	result.s.type = load_resp.s_sstatus2.tag_type;
+	result.s.tag = load_resp.s_sstatus2.tag;
+	return result;
+}
+
+/**
+ * Get the POW WQE for this core. This returns the work queue
+ * entry currently associated with this core.
+ *
+ * Returns WQE pointer
+ */
+static inline struct cvmx_wqe *cvmx_pow_get_current_wqp(void)
+{
+	cvmx_pow_load_addr_t load_addr;
+	cvmx_pow_tag_load_resp_t load_resp;
+
+	load_addr.u64 = 0;
+	load_addr.sstatus.mem_region = CVMX_IO_SEG;
+	load_addr.sstatus.is_io = 1;
+	load_addr.sstatus.did = CVMX_OCT_DID_TAG_TAG1;
+	load_addr.sstatus.coreid = cvmx_get_core_num();
+	load_addr.sstatus.get_cur = 1;
+	load_addr.sstatus.get_wqp = 1;
+	load_resp.u64 = cvmx_read_csr(load_addr.u64);
+	return (struct cvmx_wqe *) cvmx_phys_to_ptr(load_resp.s_sstatus4.wqp);
+}
+
+#ifndef CVMX_MF_CHORD
+#define CVMX_MF_CHORD(dest)	    CVMX_RDHWR(dest, 30)
+#endif
+
+/**
+ * Print a warning if a tag switch is pending for this core
+ *
+ * @function: Function name checking for a pending tag switch
+ */
+static inline void __cvmx_pow_warn_if_pending_switch(const char *function)
+{
+	uint64_t switch_complete;
+	CVMX_MF_CHORD(switch_complete);
+	if (!switch_complete)
+		pr_warn("%s called with tag switch in progress\n", function);
+}
+
+/**
+ * Waits for a tag switch to complete by polling the completion bit.
+ * Note that switches to NULL complete immediately and do not need
+ * to be waited for.
+ */
+static inline void cvmx_pow_tag_sw_wait(void)
+{
+	const uint64_t MAX_CYCLES = 1ull << 31;
+	uint64_t switch_complete;
+	uint64_t start_cycle = cvmx_get_cycle();
+	while (1) {
+		CVMX_MF_CHORD(switch_complete);
+		if (unlikely(switch_complete))
+			break;
+		if (unlikely(cvmx_get_cycle() > start_cycle + MAX_CYCLES)) {
+			pr_warn("Tag switch is taking a long time, possible deadlock\n");
+			start_cycle = -MAX_CYCLES - 1;
+		}
+	}
+}
+
+/**
+ * Synchronous work request.  Requests work from the POW.
+ * This function does NOT wait for previous tag switches to complete,
+ * so the caller must ensure that there is not a pending tag switch.
+ *
+ * @wait:   When set, call stalls until work becomes avaiable, or times out.
+ *		 If not set, returns immediately.
+ *
+ * Returns: the WQE pointer from POW. Returns NULL if no work
+ * was available.
+ */
+static inline struct cvmx_wqe *cvmx_pow_work_request_sync_nocheck(cvmx_pow_wait_t
+							     wait)
+{
+	cvmx_pow_load_addr_t ptr;
+	cvmx_pow_tag_load_resp_t result;
+
+	if (CVMX_ENABLE_POW_CHECKS)
+		__cvmx_pow_warn_if_pending_switch(__func__);
+
+	ptr.u64 = 0;
+	ptr.swork.mem_region = CVMX_IO_SEG;
+	ptr.swork.is_io = 1;
+	ptr.swork.did = CVMX_OCT_DID_TAG_SWTAG;
+	ptr.swork.wait = wait;
+
+	result.u64 = cvmx_read_csr(ptr.u64);
+
+	if (result.s_work.no_work)
+		return NULL;
+	else
+		return (struct cvmx_wqe *) cvmx_phys_to_ptr(result.s_work.addr);
+}
+
+/**
+ * Synchronous work request.  Requests work from the POW.
+ * This function waits for any previous tag switch to complete before
+ * requesting the new work.
+ *
+ * @wait:   When set, call stalls until work becomes avaiable, or times out.
+ *		 If not set, returns immediately.
+ *
+ * Returns: the WQE pointer from POW. Returns NULL if no work
+ * was available.
+ */
+static inline struct cvmx_wqe *cvmx_pow_work_request_sync(cvmx_pow_wait_t wait)
+{
+	if (CVMX_ENABLE_POW_CHECKS)
+		__cvmx_pow_warn_if_pending_switch(__func__);
+
+	/* Must not have a switch pending when requesting work */
+	cvmx_pow_tag_sw_wait();
+	return cvmx_pow_work_request_sync_nocheck(wait);
+
+}
+
+/**
+ * Synchronous null_rd request.	 Requests a switch out of NULL_NULL POW state.
+ * This function waits for any previous tag switch to complete before
+ * requesting the null_rd.
+ *
+ * Returns: the POW state of type cvmx_pow_tag_type_t.
+ */
+static inline enum cvmx_pow_tag_type cvmx_pow_work_request_null_rd(void)
+{
+	cvmx_pow_load_addr_t ptr;
+	cvmx_pow_tag_load_resp_t result;
+
+	if (CVMX_ENABLE_POW_CHECKS)
+		__cvmx_pow_warn_if_pending_switch(__func__);
+
+	/* Must not have a switch pending when requesting work */
+	cvmx_pow_tag_sw_wait();
+
+	ptr.u64 = 0;
+	ptr.snull_rd.mem_region = CVMX_IO_SEG;
+	ptr.snull_rd.is_io = 1;
+	ptr.snull_rd.did = CVMX_OCT_DID_TAG_NULL_RD;
+
+	result.u64 = cvmx_read_csr(ptr.u64);
+
+	return (enum cvmx_pow_tag_type) result.s_null_rd.state;
+}
+
+/**
+ * Asynchronous work request.  Work is requested from the POW unit,
+ * and should later be checked with function
+ * cvmx_pow_work_response_async.  This function does NOT wait for
+ * previous tag switches to complete, so the caller must ensure that
+ * there is not a pending tag switch.
+ *
+ * @scr_addr: Scratch memory address that response will be returned
+ *	      to, which is either a valid WQE, or a response with the
+ *	      invalid bit set.	Byte address, must be 8 byte aligned.
+ *
+ * @wait: 1 to cause response to wait for work to become available (or
+ *	  timeout), 0 to cause response to return immediately
+ */
+static inline void cvmx_pow_work_request_async_nocheck(int scr_addr,
+						       cvmx_pow_wait_t wait)
+{
+	cvmx_pow_iobdma_store_t data;
+
+	if (CVMX_ENABLE_POW_CHECKS)
+		__cvmx_pow_warn_if_pending_switch(__func__);
+
+	/* scr_addr must be 8 byte aligned */
+	data.s.scraddr = scr_addr >> 3;
+	data.s.len = 1;
+	data.s.did = CVMX_OCT_DID_TAG_SWTAG;
+	data.s.wait = wait;
+	cvmx_send_single(data.u64);
+}
+
+/**
+ * Asynchronous work request.  Work is requested from the POW unit,
+ * and should later be checked with function
+ * cvmx_pow_work_response_async.  This function waits for any previous
+ * tag switch to complete before requesting the new work.
+ *
+ * @scr_addr: Scratch memory address that response will be returned
+ *	      to, which is either a valid WQE, or a response with the
+ *	      invalid bit set.	Byte address, must be 8 byte aligned.
+ *
+ * @wait: 1 to cause response to wait for work to become available (or
+ *		    timeout), 0 to cause response to return immediately
+ */
+static inline void cvmx_pow_work_request_async(int scr_addr,
+					       cvmx_pow_wait_t wait)
+{
+	if (CVMX_ENABLE_POW_CHECKS)
+		__cvmx_pow_warn_if_pending_switch(__func__);
+
+	/* Must not have a switch pending when requesting work */
+	cvmx_pow_tag_sw_wait();
+	cvmx_pow_work_request_async_nocheck(scr_addr, wait);
+}
+
+/**
+ * Gets result of asynchronous work request.  Performs a IOBDMA sync
+ * to wait for the response.
+ *
+ * @scr_addr: Scratch memory address to get result from Byte address,
+ *	      must be 8 byte aligned.
+ *
+ * Returns: the WQE from the scratch register, or NULL if no
+ * work was available.
+ */
+static inline struct cvmx_wqe *cvmx_pow_work_response_async(int scr_addr)
+{
+	cvmx_pow_tag_load_resp_t result;
+
+	CVMX_SYNCIOBDMA;
+	result.u64 = cvmx_scratch_read64(scr_addr);
+
+	if (result.s_work.no_work)
+		return NULL;
+	else
+		return (struct cvmx_wqe *) cvmx_phys_to_ptr(result.s_work.addr);
+}
+
+/**
+ * Checks if a work queue entry pointer returned by a work
+ * request is valid.  It may be invalid due to no work
+ * being available or due to a timeout.
+ *
+ * @wqe_ptr: pointer to a work queue entry returned by the POW
+ *
+ * Returns 0 if pointer is valid
+ *	   1 if invalid (no work was returned)
+ */
+static inline uint64_t cvmx_pow_work_invalid(struct cvmx_wqe *wqe_ptr)
+{
+	return wqe_ptr == NULL;
+}
+
+/**
+ * Starts a tag switch to the provided tag value and tag type.
+ * Completion for the tag switch must be checked for separately.  This
+ * function does NOT update the work queue entry in dram to match tag
+ * value and type, so the application must keep track of these if they
+ * are important to the application.  This tag switch command must not
+ * be used for switches to NULL, as the tag switch pending bit will be
+ * set by the switch request, but never cleared by the hardware.
+ *
+ * NOTE: This should not be used when switching from a NULL tag.  Use
+ * cvmx_pow_tag_sw_full() instead.
+ *
+ * This function does no checks, so the caller must ensure that any
+ * previous tag switch has completed.
+ *
+ * @tag:      new tag value
+ * @tag_type: new tag type (ordered or atomic)
+ */
+static inline void cvmx_pow_tag_sw_nocheck(uint32_t tag,
+					   enum cvmx_pow_tag_type tag_type)
+{
+	cvmx_addr_t ptr;
+	cvmx_pow_tag_req_t tag_req;
+
+	if (CVMX_ENABLE_POW_CHECKS) {
+		cvmx_pow_tag_req_t current_tag;
+		__cvmx_pow_warn_if_pending_switch(__func__);
+		current_tag = cvmx_pow_get_current_tag();
+		if (current_tag.s.type == CVMX_POW_TAG_TYPE_NULL_NULL)
+			pr_warn("%s called with NULL_NULL tag\n", __func__);
+		if (current_tag.s.type == CVMX_POW_TAG_TYPE_NULL)
+			pr_warn("%s called with NULL tag\n", __func__);
+		if ((current_tag.s.type == tag_type)
+		   && (current_tag.s.tag == tag))
+			pr_warn("%s called to perform a tag switch to the same tag\n",
+				__func__);
+		if (tag_type == CVMX_POW_TAG_TYPE_NULL)
+			pr_warn("%s called to perform a tag switch to NULL. Use cvmx_pow_tag_sw_null() instead\n",
+				__func__);
+	}
+
+	/*
+	 * Note that WQE in DRAM is not updated here, as the POW does
+	 * not read from DRAM once the WQE is in flight.  See hardware
+	 * manual for complete details.	 It is the application's
+	 * responsibility to keep track of the current tag value if
+	 * that is important.
+	 */
+
+	tag_req.u64 = 0;
+	tag_req.s.op = CVMX_POW_TAG_OP_SWTAG;
+	tag_req.s.tag = tag;
+	tag_req.s.type = tag_type;
+
+	ptr.u64 = 0;
+	ptr.sio.mem_region = CVMX_IO_SEG;
+	ptr.sio.is_io = 1;
+	ptr.sio.did = CVMX_OCT_DID_TAG_SWTAG;
+
+	/* once this store arrives at POW, it will attempt the switch
+	   software must wait for the switch to complete separately */
+	cvmx_write_io(ptr.u64, tag_req.u64);
+}
+
+/**
+ * Starts a tag switch to the provided tag value and tag type.
+ * Completion for the tag switch must be checked for separately.  This
+ * function does NOT update the work queue entry in dram to match tag
+ * value and type, so the application must keep track of these if they
+ * are important to the application.  This tag switch command must not
+ * be used for switches to NULL, as the tag switch pending bit will be
+ * set by the switch request, but never cleared by the hardware.
+ *
+ * NOTE: This should not be used when switching from a NULL tag.  Use
+ * cvmx_pow_tag_sw_full() instead.
+ *
+ * This function waits for any previous tag switch to complete, and also
+ * displays an error on tag switches to NULL.
+ *
+ * @tag:      new tag value
+ * @tag_type: new tag type (ordered or atomic)
+ */
+static inline void cvmx_pow_tag_sw(uint32_t tag,
+				   enum cvmx_pow_tag_type tag_type)
+{
+	if (CVMX_ENABLE_POW_CHECKS)
+		__cvmx_pow_warn_if_pending_switch(__func__);
+
+	/*
+	 * Note that WQE in DRAM is not updated here, as the POW does
+	 * not read from DRAM once the WQE is in flight.  See hardware
+	 * manual for complete details.	 It is the application's
+	 * responsibility to keep track of the current tag value if
+	 * that is important.
+	 */
+
+	/*
+	 * Ensure that there is not a pending tag switch, as a tag
+	 * switch cannot be started if a previous switch is still
+	 * pending.
+	 */
+	cvmx_pow_tag_sw_wait();
+	cvmx_pow_tag_sw_nocheck(tag, tag_type);
+}
+
+/**
+ * Starts a tag switch to the provided tag value and tag type.
+ * Completion for the tag switch must be checked for separately.  This
+ * function does NOT update the work queue entry in dram to match tag
+ * value and type, so the application must keep track of these if they
+ * are important to the application.  This tag switch command must not
+ * be used for switches to NULL, as the tag switch pending bit will be
+ * set by the switch request, but never cleared by the hardware.
+ *
+ * This function must be used for tag switches from NULL.
+ *
+ * This function does no checks, so the caller must ensure that any
+ * previous tag switch has completed.
+ *
+ * @wqp:      pointer to work queue entry to submit.  This entry is
+ *	      updated to match the other parameters
+ * @tag:      tag value to be assigned to work queue entry
+ * @tag_type: type of tag
+ * @group:    group value for the work queue entry.
+ */
+static inline void cvmx_pow_tag_sw_full_nocheck(struct cvmx_wqe *wqp, uint32_t tag,
+						enum cvmx_pow_tag_type tag_type,
+						uint64_t group)
+{
+	cvmx_addr_t ptr;
+	cvmx_pow_tag_req_t tag_req;
+
+	if (CVMX_ENABLE_POW_CHECKS) {
+		cvmx_pow_tag_req_t current_tag;
+		__cvmx_pow_warn_if_pending_switch(__func__);
+		current_tag = cvmx_pow_get_current_tag();
+		if (current_tag.s.type == CVMX_POW_TAG_TYPE_NULL_NULL)
+			pr_warn("%s called with NULL_NULL tag\n", __func__);
+		if ((current_tag.s.type == tag_type)
+		   && (current_tag.s.tag == tag))
+			pr_warn("%s called to perform a tag switch to the same tag\n",
+				__func__);
+		if (tag_type == CVMX_POW_TAG_TYPE_NULL)
+			pr_warn("%s called to perform a tag switch to NULL. Use cvmx_pow_tag_sw_null() instead\n",
+				__func__);
+		if (wqp != cvmx_phys_to_ptr(0x80))
+			if (wqp != cvmx_pow_get_current_wqp())
+				pr_warn("%s passed WQE(%p) doesn't match the address in the POW(%p)\n",
+					__func__, wqp,
+					cvmx_pow_get_current_wqp());
+	}
+
+	/*
+	 * Note that WQE in DRAM is not updated here, as the POW does
+	 * not read from DRAM once the WQE is in flight.  See hardware
+	 * manual for complete details.	 It is the application's
+	 * responsibility to keep track of the current tag value if
+	 * that is important.
+	 */
+
+	tag_req.u64 = 0;
+	tag_req.s.op = CVMX_POW_TAG_OP_SWTAG_FULL;
+	tag_req.s.tag = tag;
+	tag_req.s.type = tag_type;
+	tag_req.s.grp = group;
+
+	ptr.u64 = 0;
+	ptr.sio.mem_region = CVMX_IO_SEG;
+	ptr.sio.is_io = 1;
+	ptr.sio.did = CVMX_OCT_DID_TAG_SWTAG;
+	ptr.sio.offset = CAST64(wqp);
+
+	/*
+	 * once this store arrives at POW, it will attempt the switch
+	 * software must wait for the switch to complete separately.
+	 */
+	cvmx_write_io(ptr.u64, tag_req.u64);
+}
+
+/**
+ * Starts a tag switch to the provided tag value and tag type.
+ * Completion for the tag switch must be checked for separately.  This
+ * function does NOT update the work queue entry in dram to match tag
+ * value and type, so the application must keep track of these if they
+ * are important to the application.  This tag switch command must not
+ * be used for switches to NULL, as the tag switch pending bit will be
+ * set by the switch request, but never cleared by the hardware.
+ *
+ * This function must be used for tag switches from NULL.
+ *
+ * This function waits for any pending tag switches to complete
+ * before requesting the tag switch.
+ *
+ * @wqp:      pointer to work queue entry to submit.  This entry is updated
+ *	      to match the other parameters
+ * @tag:      tag value to be assigned to work queue entry
+ * @tag_type: type of tag
+ * @group:	group value for the work queue entry.
+ */
+static inline void cvmx_pow_tag_sw_full(struct cvmx_wqe *wqp, uint32_t tag,
+					enum cvmx_pow_tag_type tag_type,
+					uint64_t group)
+{
+	if (CVMX_ENABLE_POW_CHECKS)
+		__cvmx_pow_warn_if_pending_switch(__func__);
+
+	/*
+	 * Ensure that there is not a pending tag switch, as a tag
+	 * switch cannot be started if a previous switch is still
+	 * pending.
+	 */
+	cvmx_pow_tag_sw_wait();
+	cvmx_pow_tag_sw_full_nocheck(wqp, tag, tag_type, group);
+}
+
+/**
+ * Switch to a NULL tag, which ends any ordering or
+ * synchronization provided by the POW for the current
+ * work queue entry.  This operation completes immediately,
+ * so completion should not be waited for.
+ * This function does NOT wait for previous tag switches to complete,
+ * so the caller must ensure that any previous tag switches have completed.
+ */
+static inline void cvmx_pow_tag_sw_null_nocheck(void)
+{
+	cvmx_addr_t ptr;
+	cvmx_pow_tag_req_t tag_req;
+
+	if (CVMX_ENABLE_POW_CHECKS) {
+		cvmx_pow_tag_req_t current_tag;
+		__cvmx_pow_warn_if_pending_switch(__func__);
+		current_tag = cvmx_pow_get_current_tag();
+		if (current_tag.s.type == CVMX_POW_TAG_TYPE_NULL_NULL)
+			pr_warn("%s called with NULL_NULL tag\n", __func__);
+		if (current_tag.s.type == CVMX_POW_TAG_TYPE_NULL)
+			pr_warn("%s called when we already have a NULL tag\n",
+				__func__);
+	}
+
+	tag_req.u64 = 0;
+	tag_req.s.op = CVMX_POW_TAG_OP_SWTAG;
+	tag_req.s.type = CVMX_POW_TAG_TYPE_NULL;
+
+	ptr.u64 = 0;
+	ptr.sio.mem_region = CVMX_IO_SEG;
+	ptr.sio.is_io = 1;
+	ptr.sio.did = CVMX_OCT_DID_TAG_TAG1;
+
+	cvmx_write_io(ptr.u64, tag_req.u64);
+
+	/* switch to NULL completes immediately */
+}
+
+/**
+ * Switch to a NULL tag, which ends any ordering or
+ * synchronization provided by the POW for the current
+ * work queue entry.  This operation completes immediately,
+ * so completion should not be waited for.
+ * This function waits for any pending tag switches to complete
+ * before requesting the switch to NULL.
+ */
+static inline void cvmx_pow_tag_sw_null(void)
+{
+	if (CVMX_ENABLE_POW_CHECKS)
+		__cvmx_pow_warn_if_pending_switch(__func__);
+
+	/*
+	 * Ensure that there is not a pending tag switch, as a tag
+	 * switch cannot be started if a previous switch is still
+	 * pending.
+	 */
+	cvmx_pow_tag_sw_wait();
+	cvmx_pow_tag_sw_null_nocheck();
+
+	/* switch to NULL completes immediately */
+}
+
+/**
+ * Submits work to an input queue.  This function updates the work
+ * queue entry in DRAM to match the arguments given.  Note that the
+ * tag provided is for the work queue entry submitted, and is
+ * unrelated to the tag that the core currently holds.
+ *
+ * @wqp:      pointer to work queue entry to submit.  This entry is
+ *	      updated to match the other parameters
+ * @tag:      tag value to be assigned to work queue entry
+ * @tag_type: type of tag
+ * @qos:      Input queue to add to.
+ * @grp:      group value for the work queue entry.
+ */
+static inline void cvmx_pow_work_submit(struct cvmx_wqe *wqp, uint32_t tag,
+					enum cvmx_pow_tag_type tag_type,
+					uint64_t qos, uint64_t grp)
+{
+	cvmx_addr_t ptr;
+	cvmx_pow_tag_req_t tag_req;
+
+	wqp->word1.tag = tag;
+	wqp->word1.tag_type = tag_type;
+
+	cvmx_wqe_set_qos(wqp, qos);
+	cvmx_wqe_set_grp(wqp, grp);
+
+	tag_req.u64 = 0;
+	tag_req.s.op = CVMX_POW_TAG_OP_ADDWQ;
+	tag_req.s.type = tag_type;
+	tag_req.s.tag = tag;
+	tag_req.s.qos = qos;
+	tag_req.s.grp = grp;
+
+	ptr.u64 = 0;
+	ptr.sio.mem_region = CVMX_IO_SEG;
+	ptr.sio.is_io = 1;
+	ptr.sio.did = CVMX_OCT_DID_TAG_TAG1;
+	ptr.sio.offset = cvmx_ptr_to_phys(wqp);
+
+	/*
+	 * SYNC write to memory before the work submit.	 This is
+	 * necessary as POW may read values from DRAM at this time.
+	 */
+	CVMX_SYNCWS;
+	cvmx_write_io(ptr.u64, tag_req.u64);
+}
+
+/**
+ * This function sets the group mask for a core.  The group mask
+ * indicates which groups each core will accept work from. There are
+ * 16 groups.
+ *
+ * @core_num:	core to apply mask to
+ * @mask:   Group mask. There are 16 groups, so only bits 0-15 are valid,
+ *		 representing groups 0-15.
+ *		 Each 1 bit in the mask enables the core to accept work from
+ *		 the corresponding group.
+ */
+static inline void cvmx_pow_set_group_mask(uint64_t core_num, uint64_t mask)
+{
+	union cvmx_pow_pp_grp_mskx grp_msk;
+
+	grp_msk.u64 = cvmx_read_csr(CVMX_POW_PP_GRP_MSKX(core_num));
+	grp_msk.s.grp_msk = mask;
+	cvmx_write_csr(CVMX_POW_PP_GRP_MSKX(core_num), grp_msk.u64);
+}
+
+/**
+ * This function sets POW static priorities for a core. Each input queue has
+ * an associated priority value.
+ *
+ * @core_num:	core to apply priorities to
+ * @priority:	Vector of 8 priorities, one per POW Input Queue (0-7).
+ *		     Highest priority is 0 and lowest is 7. A priority value
+ *		     of 0xF instructs POW to skip the Input Queue when
+ *		     scheduling to this specific core.
+ *		     NOTE: priorities should not have gaps in values, meaning
+ *			   {0,1,1,1,1,1,1,1} is a valid configuration while
+ *			   {0,2,2,2,2,2,2,2} is not.
+ */
+static inline void cvmx_pow_set_priority(uint64_t core_num,
+					 const uint8_t priority[])
+{
+	/* POW priorities are supported on CN5xxx and later */
+	if (!OCTEON_IS_MODEL(OCTEON_CN3XXX)) {
+		union cvmx_pow_pp_grp_mskx grp_msk;
+
+		grp_msk.u64 = cvmx_read_csr(CVMX_POW_PP_GRP_MSKX(core_num));
+		grp_msk.s.qos0_pri = priority[0];
+		grp_msk.s.qos1_pri = priority[1];
+		grp_msk.s.qos2_pri = priority[2];
+		grp_msk.s.qos3_pri = priority[3];
+		grp_msk.s.qos4_pri = priority[4];
+		grp_msk.s.qos5_pri = priority[5];
+		grp_msk.s.qos6_pri = priority[6];
+		grp_msk.s.qos7_pri = priority[7];
+
+		/* Detect gaps between priorities and flag error */
+		{
+			int i;
+			uint32_t prio_mask = 0;
+
+			for (i = 0; i < 8; i++)
+				if (priority[i] != 0xF)
+					prio_mask |= 1 << priority[i];
+
+			if (prio_mask ^ ((1 << cvmx_pop(prio_mask)) - 1)) {
+				pr_err("POW static priorities should be "
+				       "contiguous (0x%llx)\n",
+				     (unsigned long long)prio_mask);
+				return;
+			}
+		}
+
+		cvmx_write_csr(CVMX_POW_PP_GRP_MSKX(core_num), grp_msk.u64);
+	}
+}
+
+/**
+ * Performs a tag switch and then an immediate deschedule. This completes
+ * immediately, so completion must not be waited for.  This function does NOT
+ * update the wqe in DRAM to match arguments.
+ *
+ * This function does NOT wait for any prior tag switches to complete, so the
+ * calling code must do this.
+ *
+ * Note the following CAVEAT of the Octeon HW behavior when
+ * re-scheduling DE-SCHEDULEd items whose (next) state is
+ * ORDERED:
+ *   - If there are no switches pending at the time that the
+ *     HW executes the de-schedule, the HW will only re-schedule
+ *     the head of the FIFO associated with the given tag. This
+ *     means that in many respects, the HW treats this ORDERED
+ *     tag as an ATOMIC tag. Note that in the SWTAG_DESCH
+ *     case (to an ORDERED tag), the HW will do the switch
+ *     before the deschedule whenever it is possible to do
+ *     the switch immediately, so it may often look like
+ *     this case.
+ *   - If there is a pending switch to ORDERED at the time
+ *     the HW executes the de-schedule, the HW will perform
+ *     the switch at the time it re-schedules, and will be
+ *     able to reschedule any/all of the entries with the
+ *     same tag.
+ * Due to this behavior, the RECOMMENDATION to software is
+ * that they have a (next) state of ATOMIC when they
+ * DE-SCHEDULE. If an ORDERED tag is what was really desired,
+ * SW can choose to immediately switch to an ORDERED tag
+ * after the work (that has an ATOMIC tag) is re-scheduled.
+ * Note that since there are never any tag switches pending
+ * when the HW re-schedules, this switch can be IMMEDIATE upon
+ * the reception of the pointer during the re-schedule.
+ *
+ * @tag:      New tag value
+ * @tag_type: New tag type
+ * @group:    New group value
+ * @no_sched: Control whether this work queue entry will be rescheduled.
+ *		   - 1 : don't schedule this work
+ *		   - 0 : allow this work to be scheduled.
+ */
+static inline void cvmx_pow_tag_sw_desched_nocheck(
+	uint32_t tag,
+	enum cvmx_pow_tag_type tag_type,
+	uint64_t group,
+	uint64_t no_sched)
+{
+	cvmx_addr_t ptr;
+	cvmx_pow_tag_req_t tag_req;
+
+	if (CVMX_ENABLE_POW_CHECKS) {
+		cvmx_pow_tag_req_t current_tag;
+		__cvmx_pow_warn_if_pending_switch(__func__);
+		current_tag = cvmx_pow_get_current_tag();
+		if (current_tag.s.type == CVMX_POW_TAG_TYPE_NULL_NULL)
+			pr_warn("%s called with NULL_NULL tag\n", __func__);
+		if (current_tag.s.type == CVMX_POW_TAG_TYPE_NULL)
+			pr_warn("%s called with NULL tag. Deschedule not allowed from NULL state\n",
+				__func__);
+		if ((current_tag.s.type != CVMX_POW_TAG_TYPE_ATOMIC)
+			&& (tag_type != CVMX_POW_TAG_TYPE_ATOMIC))
+			pr_warn("%s called where neither the before or after tag is ATOMIC\n",
+				__func__);
+	}
+
+	tag_req.u64 = 0;
+	tag_req.s.op = CVMX_POW_TAG_OP_SWTAG_DESCH;
+	tag_req.s.tag = tag;
+	tag_req.s.type = tag_type;
+	tag_req.s.grp = group;
+	tag_req.s.no_sched = no_sched;
+
+	ptr.u64 = 0;
+	ptr.sio.mem_region = CVMX_IO_SEG;
+	ptr.sio.is_io = 1;
+	ptr.sio.did = CVMX_OCT_DID_TAG_TAG3;
+	/*
+	 * since TAG3 is used, this store will clear the local pending
+	 * switch bit.
+	 */
+	cvmx_write_io(ptr.u64, tag_req.u64);
+}
+
+/**
+ * Performs a tag switch and then an immediate deschedule. This completes
+ * immediately, so completion must not be waited for.  This function does NOT
+ * update the wqe in DRAM to match arguments.
+ *
+ * This function waits for any prior tag switches to complete, so the
+ * calling code may call this function with a pending tag switch.
+ *
+ * Note the following CAVEAT of the Octeon HW behavior when
+ * re-scheduling DE-SCHEDULEd items whose (next) state is
+ * ORDERED:
+ *   - If there are no switches pending at the time that the
+ *     HW executes the de-schedule, the HW will only re-schedule
+ *     the head of the FIFO associated with the given tag. This
+ *     means that in many respects, the HW treats this ORDERED
+ *     tag as an ATOMIC tag. Note that in the SWTAG_DESCH
+ *     case (to an ORDERED tag), the HW will do the switch
+ *     before the deschedule whenever it is possible to do
+ *     the switch immediately, so it may often look like
+ *     this case.
+ *   - If there is a pending switch to ORDERED at the time
+ *     the HW executes the de-schedule, the HW will perform
+ *     the switch at the time it re-schedules, and will be
+ *     able to reschedule any/all of the entries with the
+ *     same tag.
+ * Due to this behavior, the RECOMMENDATION to software is
+ * that they have a (next) state of ATOMIC when they
+ * DE-SCHEDULE. If an ORDERED tag is what was really desired,
+ * SW can choose to immediately switch to an ORDERED tag
+ * after the work (that has an ATOMIC tag) is re-scheduled.
+ * Note that since there are never any tag switches pending
+ * when the HW re-schedules, this switch can be IMMEDIATE upon
+ * the reception of the pointer during the re-schedule.
+ *
+ * @tag:      New tag value
+ * @tag_type: New tag type
+ * @group:    New group value
+ * @no_sched: Control whether this work queue entry will be rescheduled.
+ *		   - 1 : don't schedule this work
+ *		   - 0 : allow this work to be scheduled.
+ */
+static inline void cvmx_pow_tag_sw_desched(uint32_t tag,
+					   enum cvmx_pow_tag_type tag_type,
+					   uint64_t group, uint64_t no_sched)
+{
+	if (CVMX_ENABLE_POW_CHECKS)
+		__cvmx_pow_warn_if_pending_switch(__func__);
+
+	/* Need to make sure any writes to the work queue entry are complete */
+	CVMX_SYNCWS;
+	/*
+	 * Ensure that there is not a pending tag switch, as a tag
+	 * switch cannot be started if a previous switch is still
+	 * pending.
+	 */
+	cvmx_pow_tag_sw_wait();
+	cvmx_pow_tag_sw_desched_nocheck(tag, tag_type, group, no_sched);
+}
+
+/**
+ * Deschedules the current work queue entry.
+ *
+ * @no_sched: no schedule flag value to be set on the work queue
+ *	      entry.  If this is set the entry will not be
+ *	      rescheduled.
+ */
+static inline void cvmx_pow_desched(uint64_t no_sched)
+{
+	cvmx_addr_t ptr;
+	cvmx_pow_tag_req_t tag_req;
+
+	if (CVMX_ENABLE_POW_CHECKS) {
+		cvmx_pow_tag_req_t current_tag;
+		__cvmx_pow_warn_if_pending_switch(__func__);
+		current_tag = cvmx_pow_get_current_tag();
+		if (current_tag.s.type == CVMX_POW_TAG_TYPE_NULL_NULL)
+			pr_warn("%s called with NULL_NULL tag\n", __func__);
+		if (current_tag.s.type == CVMX_POW_TAG_TYPE_NULL)
+			pr_warn("%s called with NULL tag. Deschedule not expected from NULL state\n",
+				__func__);
+	}
+
+	/* Need to make sure any writes to the work queue entry are complete */
+	CVMX_SYNCWS;
+
+	tag_req.u64 = 0;
+	tag_req.s.op = CVMX_POW_TAG_OP_DESCH;
+	tag_req.s.no_sched = no_sched;
+
+	ptr.u64 = 0;
+	ptr.sio.mem_region = CVMX_IO_SEG;
+	ptr.sio.is_io = 1;
+	ptr.sio.did = CVMX_OCT_DID_TAG_TAG3;
+	/*
+	 * since TAG3 is used, this store will clear the local pending
+	 * switch bit.
+	 */
+	cvmx_write_io(ptr.u64, tag_req.u64);
+}
+
+/****************************************************
+* Define usage of bits within the 32 bit tag values.
+*****************************************************/
+
+/*
+ * Number of bits of the tag used by software.	The SW bits are always
+ * a contiguous block of the high starting at bit 31.  The hardware
+ * bits are always the low bits.  By default, the top 8 bits of the
+ * tag are reserved for software, and the low 24 are set by the IPD
+ * unit.
+ */
+#define CVMX_TAG_SW_BITS    (8)
+#define CVMX_TAG_SW_SHIFT   (32 - CVMX_TAG_SW_BITS)
+
+/* Below is the list of values for the top 8 bits of the tag. */
+/*
+ * Tag values with top byte of this value are reserved for internal
+ * executive uses.
+ */
+#define CVMX_TAG_SW_BITS_INTERNAL  0x1
+/* The executive divides the remaining 24 bits as follows:
+ *  - the upper 8 bits (bits 23 - 16 of the tag) define a subgroup
+ *
+ *  - the lower 16 bits (bits 15 - 0 of the tag) define are the value
+ *    with the subgroup
+ *
+ * Note that this section describes the format of tags generated by
+ * software - refer to the hardware documentation for a description of
+ * the tags values generated by the packet input hardware.  Subgroups
+ * are defined here.
+ */
+/* Mask for the value portion of the tag */
+#define CVMX_TAG_SUBGROUP_MASK	0xFFFF
+#define CVMX_TAG_SUBGROUP_SHIFT 16
+#define CVMX_TAG_SUBGROUP_PKO  0x1
+
+/* End of executive tag subgroup definitions */
+
+/*
+ * The remaining values software bit values 0x2 - 0xff are available
+ * for application use.
+ */
+
+/**
+ * This function creates a 32 bit tag value from the two values provided.
+ *
+ * @sw_bits: The upper bits (number depends on configuration) are set
+ *	     to this value.  The remainder of bits are set by the
+ *	     hw_bits parameter.
+ *
+ * @hw_bits: The lower bits (number depends on configuration) are set
+ *	     to this value.  The remainder of bits are set by the
+ *	     sw_bits parameter.
+ *
+ * Returns 32 bit value of the combined hw and sw bits.
+ */
+static inline uint32_t cvmx_pow_tag_compose(uint64_t sw_bits, uint64_t hw_bits)
+{
+	return ((sw_bits & cvmx_build_mask(CVMX_TAG_SW_BITS)) <<
+			CVMX_TAG_SW_SHIFT) |
+		(hw_bits & cvmx_build_mask(32 - CVMX_TAG_SW_BITS));
+}
+
+/**
+ * Extracts the bits allocated for software use from the tag
+ *
+ * @tag:    32 bit tag value
+ *
+ * Returns N bit software tag value, where N is configurable with the
+ * CVMX_TAG_SW_BITS define
+ */
+static inline uint32_t cvmx_pow_tag_get_sw_bits(uint64_t tag)
+{
+	return (tag >> (32 - CVMX_TAG_SW_BITS)) &
+		cvmx_build_mask(CVMX_TAG_SW_BITS);
+}
+
+/**
+ *
+ * Extracts the bits allocated for hardware use from the tag
+ *
+ * @tag:    32 bit tag value
+ *
+ * Returns (32 - N) bit software tag value, where N is configurable
+ * with the CVMX_TAG_SW_BITS define
+ */
+static inline uint32_t cvmx_pow_tag_get_hw_bits(uint64_t tag)
+{
+	return tag & cvmx_build_mask(32 - CVMX_TAG_SW_BITS);
+}
+
+/**
+ * Store the current POW internal state into the supplied
+ * buffer. It is recommended that you pass a buffer of at least
+ * 128KB. The format of the capture may change based on SDK
+ * version and Octeon chip.
+ *
+ * @buffer: Buffer to store capture into
+ * @buffer_size:
+ *		 The size of the supplied buffer
+ *
+ * Returns Zero on success, negative on failure
+ */
+extern int cvmx_pow_capture(void *buffer, int buffer_size);
+
+/**
+ * Dump a POW capture to the console in a human readable format.
+ *
+ * @buffer: POW capture from cvmx_pow_capture()
+ * @buffer_size:
+ *		 Size of the buffer
+ */
+extern void cvmx_pow_display(void *buffer, int buffer_size);
+
+/**
+ * Return the number of POW entries supported by this chip
+ *
+ * Returns Number of POW entries
+ */
+extern int cvmx_pow_get_num_entries(void);
+
+#endif /* __CVMX_POW_H__ */
diff --git a/arch/mips/include/asm/octeon/cvmx-rnm-defs.h b/arch/mips/include/asm/octeon/cvmx-rnm-defs.h
new file mode 100644
index 000000000..94295d2fe
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-rnm-defs.h
@@ -0,0 +1,171 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2012 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_RNM_DEFS_H__
+#define __CVMX_RNM_DEFS_H__
+
+#define CVMX_RNM_BIST_STATUS (CVMX_ADD_IO_SEG(0x0001180040000008ull))
+#define CVMX_RNM_CTL_STATUS (CVMX_ADD_IO_SEG(0x0001180040000000ull))
+#define CVMX_RNM_EER_DBG (CVMX_ADD_IO_SEG(0x0001180040000018ull))
+#define CVMX_RNM_EER_KEY (CVMX_ADD_IO_SEG(0x0001180040000010ull))
+#define CVMX_RNM_SERIAL_NUM (CVMX_ADD_IO_SEG(0x0001180040000020ull))
+
+union cvmx_rnm_bist_status {
+	uint64_t u64;
+	struct cvmx_rnm_bist_status_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t rrc:1;
+		uint64_t mem:1;
+#else
+		uint64_t mem:1;
+		uint64_t rrc:1;
+		uint64_t reserved_2_63:62;
+#endif
+	} s;
+};
+
+union cvmx_rnm_ctl_status {
+	uint64_t u64;
+	struct cvmx_rnm_ctl_status_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t dis_mak:1;
+		uint64_t eer_lck:1;
+		uint64_t eer_val:1;
+		uint64_t ent_sel:4;
+		uint64_t exp_ent:1;
+		uint64_t rng_rst:1;
+		uint64_t rnm_rst:1;
+		uint64_t rng_en:1;
+		uint64_t ent_en:1;
+#else
+		uint64_t ent_en:1;
+		uint64_t rng_en:1;
+		uint64_t rnm_rst:1;
+		uint64_t rng_rst:1;
+		uint64_t exp_ent:1;
+		uint64_t ent_sel:4;
+		uint64_t eer_val:1;
+		uint64_t eer_lck:1;
+		uint64_t dis_mak:1;
+		uint64_t reserved_12_63:52;
+#endif
+	} s;
+	struct cvmx_rnm_ctl_status_cn30xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t rng_rst:1;
+		uint64_t rnm_rst:1;
+		uint64_t rng_en:1;
+		uint64_t ent_en:1;
+#else
+		uint64_t ent_en:1;
+		uint64_t rng_en:1;
+		uint64_t rnm_rst:1;
+		uint64_t rng_rst:1;
+		uint64_t reserved_4_63:60;
+#endif
+	} cn30xx;
+	struct cvmx_rnm_ctl_status_cn50xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_9_63:55;
+		uint64_t ent_sel:4;
+		uint64_t exp_ent:1;
+		uint64_t rng_rst:1;
+		uint64_t rnm_rst:1;
+		uint64_t rng_en:1;
+		uint64_t ent_en:1;
+#else
+		uint64_t ent_en:1;
+		uint64_t rng_en:1;
+		uint64_t rnm_rst:1;
+		uint64_t rng_rst:1;
+		uint64_t exp_ent:1;
+		uint64_t ent_sel:4;
+		uint64_t reserved_9_63:55;
+#endif
+	} cn50xx;
+	struct cvmx_rnm_ctl_status_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_11_63:53;
+		uint64_t eer_lck:1;
+		uint64_t eer_val:1;
+		uint64_t ent_sel:4;
+		uint64_t exp_ent:1;
+		uint64_t rng_rst:1;
+		uint64_t rnm_rst:1;
+		uint64_t rng_en:1;
+		uint64_t ent_en:1;
+#else
+		uint64_t ent_en:1;
+		uint64_t rng_en:1;
+		uint64_t rnm_rst:1;
+		uint64_t rng_rst:1;
+		uint64_t exp_ent:1;
+		uint64_t ent_sel:4;
+		uint64_t eer_val:1;
+		uint64_t eer_lck:1;
+		uint64_t reserved_11_63:53;
+#endif
+	} cn63xx;
+};
+
+union cvmx_rnm_eer_dbg {
+	uint64_t u64;
+	struct cvmx_rnm_eer_dbg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t dat:64;
+#else
+		uint64_t dat:64;
+#endif
+	} s;
+};
+
+union cvmx_rnm_eer_key {
+	uint64_t u64;
+	struct cvmx_rnm_eer_key_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t key:64;
+#else
+		uint64_t key:64;
+#endif
+	} s;
+};
+
+union cvmx_rnm_serial_num {
+	uint64_t u64;
+	struct cvmx_rnm_serial_num_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t dat:64;
+#else
+		uint64_t dat:64;
+#endif
+	} s;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-rst-defs.h b/arch/mips/include/asm/octeon/cvmx-rst-defs.h
new file mode 100644
index 000000000..accc9977d
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-rst-defs.h
@@ -0,0 +1,278 @@
+/***********************license start***************
+ * Author: Cavium Inc.
+ *
+ * Contact: support@cavium.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2014 Cavium Inc.
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Inc. for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_RST_DEFS_H__
+#define __CVMX_RST_DEFS_H__
+
+#define CVMX_RST_BOOT (CVMX_ADD_IO_SEG(0x0001180006001600ull))
+#define CVMX_RST_CFG (CVMX_ADD_IO_SEG(0x0001180006001610ull))
+#define CVMX_RST_CKILL (CVMX_ADD_IO_SEG(0x0001180006001638ull))
+#define CVMX_RST_CTLX(offset) (CVMX_ADD_IO_SEG(0x0001180006001640ull) + ((offset) & 3) * 8)
+#define CVMX_RST_DELAY (CVMX_ADD_IO_SEG(0x0001180006001608ull))
+#define CVMX_RST_ECO (CVMX_ADD_IO_SEG(0x00011800060017B8ull))
+#define CVMX_RST_INT (CVMX_ADD_IO_SEG(0x0001180006001628ull))
+#define CVMX_RST_OCX (CVMX_ADD_IO_SEG(0x0001180006001618ull))
+#define CVMX_RST_POWER_DBG (CVMX_ADD_IO_SEG(0x0001180006001708ull))
+#define CVMX_RST_PP_POWER (CVMX_ADD_IO_SEG(0x0001180006001700ull))
+#define CVMX_RST_SOFT_PRSTX(offset) (CVMX_ADD_IO_SEG(0x00011800060016C0ull) + ((offset) & 3) * 8)
+#define CVMX_RST_SOFT_RST (CVMX_ADD_IO_SEG(0x0001180006001680ull))
+
+union cvmx_rst_boot {
+	uint64_t u64;
+	struct cvmx_rst_boot_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t chipkill:1;
+		uint64_t jtcsrdis:1;
+		uint64_t ejtagdis:1;
+		uint64_t romen:1;
+		uint64_t ckill_ppdis:1;
+		uint64_t jt_tstmode:1;
+		uint64_t vrm_err:1;
+		uint64_t reserved_37_56:20;
+		uint64_t c_mul:7;
+		uint64_t pnr_mul:6;
+		uint64_t reserved_21_23:3;
+		uint64_t lboot_oci:3;
+		uint64_t lboot_ext:6;
+		uint64_t lboot:10;
+		uint64_t rboot:1;
+		uint64_t rboot_pin:1;
+#else
+		uint64_t rboot_pin:1;
+		uint64_t rboot:1;
+		uint64_t lboot:10;
+		uint64_t lboot_ext:6;
+		uint64_t lboot_oci:3;
+		uint64_t reserved_21_23:3;
+		uint64_t pnr_mul:6;
+		uint64_t c_mul:7;
+		uint64_t reserved_37_56:20;
+		uint64_t vrm_err:1;
+		uint64_t jt_tstmode:1;
+		uint64_t ckill_ppdis:1;
+		uint64_t romen:1;
+		uint64_t ejtagdis:1;
+		uint64_t jtcsrdis:1;
+		uint64_t chipkill:1;
+#endif
+	} s;
+};
+
+union cvmx_rst_cfg {
+	uint64_t u64;
+	struct cvmx_rst_cfg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t bist_delay:58;
+		uint64_t reserved_3_5:3;
+		uint64_t cntl_clr_bist:1;
+		uint64_t warm_clr_bist:1;
+		uint64_t soft_clr_bist:1;
+#else
+		uint64_t soft_clr_bist:1;
+		uint64_t warm_clr_bist:1;
+		uint64_t cntl_clr_bist:1;
+		uint64_t reserved_3_5:3;
+		uint64_t bist_delay:58;
+#endif
+	} s;
+};
+
+union cvmx_rst_ckill {
+	uint64_t u64;
+	struct cvmx_rst_ckill_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_47_63:17;
+		uint64_t timer:47;
+#else
+		uint64_t timer:47;
+		uint64_t reserved_47_63:17;
+#endif
+	} s;
+};
+
+union cvmx_rst_ctlx {
+	uint64_t u64;
+	struct cvmx_rst_ctlx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t prst_link:1;
+		uint64_t rst_done:1;
+		uint64_t rst_link:1;
+		uint64_t host_mode:1;
+		uint64_t reserved_4_5:2;
+		uint64_t rst_drv:1;
+		uint64_t rst_rcv:1;
+		uint64_t rst_chip:1;
+		uint64_t rst_val:1;
+#else
+		uint64_t rst_val:1;
+		uint64_t rst_chip:1;
+		uint64_t rst_rcv:1;
+		uint64_t rst_drv:1;
+		uint64_t reserved_4_5:2;
+		uint64_t host_mode:1;
+		uint64_t rst_link:1;
+		uint64_t rst_done:1;
+		uint64_t prst_link:1;
+		uint64_t reserved_10_63:54;
+#endif
+	} s;
+};
+
+union cvmx_rst_delay {
+	uint64_t u64;
+	struct cvmx_rst_delay_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t warm_rst_dly:16;
+		uint64_t soft_rst_dly:16;
+#else
+		uint64_t soft_rst_dly:16;
+		uint64_t warm_rst_dly:16;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_rst_eco {
+	uint64_t u64;
+	struct cvmx_rst_eco_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t eco_rw:32;
+#else
+		uint64_t eco_rw:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_rst_int {
+	uint64_t u64;
+	struct cvmx_rst_int_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t perst:4;
+		uint64_t reserved_4_7:4;
+		uint64_t rst_link:4;
+#else
+		uint64_t rst_link:4;
+		uint64_t reserved_4_7:4;
+		uint64_t perst:4;
+		uint64_t reserved_12_63:52;
+#endif
+	} s;
+	struct cvmx_rst_int_cn70xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_11_63:53;
+		uint64_t perst:3;
+		uint64_t reserved_3_7:5;
+		uint64_t rst_link:3;
+#else
+		uint64_t rst_link:3;
+		uint64_t reserved_3_7:5;
+		uint64_t perst:3;
+		uint64_t reserved_11_63:53;
+#endif
+	} cn70xx;
+};
+
+union cvmx_rst_ocx {
+	uint64_t u64;
+	struct cvmx_rst_ocx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_3_63:61;
+		uint64_t rst_link:3;
+#else
+		uint64_t rst_link:3;
+		uint64_t reserved_3_63:61;
+#endif
+	} s;
+};
+
+union cvmx_rst_power_dbg {
+	uint64_t u64;
+	struct cvmx_rst_power_dbg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_3_63:61;
+		uint64_t str:3;
+#else
+		uint64_t str:3;
+		uint64_t reserved_3_63:61;
+#endif
+	} s;
+};
+
+union cvmx_rst_pp_power {
+	uint64_t u64;
+	struct cvmx_rst_pp_power_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t gate:48;
+#else
+		uint64_t gate:48;
+		uint64_t reserved_48_63:16;
+#endif
+	} s;
+	struct cvmx_rst_pp_power_cn70xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t gate:4;
+#else
+		uint64_t gate:4;
+		uint64_t reserved_4_63:60;
+#endif
+	} cn70xx;
+};
+
+union cvmx_rst_soft_prstx {
+	uint64_t u64;
+	struct cvmx_rst_soft_prstx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t soft_prst:1;
+#else
+		uint64_t soft_prst:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_rst_soft_rst {
+	uint64_t u64;
+	struct cvmx_rst_soft_rst_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t soft_rst:1;
+#else
+		uint64_t soft_rst:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-scratch.h b/arch/mips/include/asm/octeon/cvmx-scratch.h
new file mode 100644
index 000000000..8d21cc5e4
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-scratch.h
@@ -0,0 +1,139 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/**
+ *
+ * This file provides support for the processor local scratch memory.
+ * Scratch memory is byte addressable - all addresses are byte addresses.
+ *
+ */
+
+#ifndef __CVMX_SCRATCH_H__
+#define __CVMX_SCRATCH_H__
+
+/*
+ * Note: This define must be a long, not a long long in order to
+ * compile without warnings for both 32bit and 64bit.
+ */
+#define CVMX_SCRATCH_BASE	(-32768l)	/* 0xffffffffffff8000 */
+
+/**
+ * Reads an 8 bit value from the processor local scratchpad memory.
+ *
+ * @address: byte address to read from
+ *
+ * Returns value read
+ */
+static inline uint8_t cvmx_scratch_read8(uint64_t address)
+{
+	return *CASTPTR(volatile uint8_t, CVMX_SCRATCH_BASE + address);
+}
+
+/**
+ * Reads a 16 bit value from the processor local scratchpad memory.
+ *
+ * @address: byte address to read from
+ *
+ * Returns value read
+ */
+static inline uint16_t cvmx_scratch_read16(uint64_t address)
+{
+	return *CASTPTR(volatile uint16_t, CVMX_SCRATCH_BASE + address);
+}
+
+/**
+ * Reads a 32 bit value from the processor local scratchpad memory.
+ *
+ * @address: byte address to read from
+ *
+ * Returns value read
+ */
+static inline uint32_t cvmx_scratch_read32(uint64_t address)
+{
+	return *CASTPTR(volatile uint32_t, CVMX_SCRATCH_BASE + address);
+}
+
+/**
+ * Reads a 64 bit value from the processor local scratchpad memory.
+ *
+ * @address: byte address to read from
+ *
+ * Returns value read
+ */
+static inline uint64_t cvmx_scratch_read64(uint64_t address)
+{
+	return *CASTPTR(volatile uint64_t, CVMX_SCRATCH_BASE + address);
+}
+
+/**
+ * Writes an 8 bit value to the processor local scratchpad memory.
+ *
+ * @address: byte address to write to
+ * @value:   value to write
+ */
+static inline void cvmx_scratch_write8(uint64_t address, uint64_t value)
+{
+	*CASTPTR(volatile uint8_t, CVMX_SCRATCH_BASE + address) =
+	    (uint8_t) value;
+}
+
+/**
+ * Writes a 32 bit value to the processor local scratchpad memory.
+ *
+ * @address: byte address to write to
+ * @value:   value to write
+ */
+static inline void cvmx_scratch_write16(uint64_t address, uint64_t value)
+{
+	*CASTPTR(volatile uint16_t, CVMX_SCRATCH_BASE + address) =
+	    (uint16_t) value;
+}
+
+/**
+ * Writes a 16 bit value to the processor local scratchpad memory.
+ *
+ * @address: byte address to write to
+ * @value:   value to write
+ */
+static inline void cvmx_scratch_write32(uint64_t address, uint64_t value)
+{
+	*CASTPTR(volatile uint32_t, CVMX_SCRATCH_BASE + address) =
+	    (uint32_t) value;
+}
+
+/**
+ * Writes a 64 bit value to the processor local scratchpad memory.
+ *
+ * @address: byte address to write to
+ * @value:   value to write
+ */
+static inline void cvmx_scratch_write64(uint64_t address, uint64_t value)
+{
+	*CASTPTR(volatile uint64_t, CVMX_SCRATCH_BASE + address) = value;
+}
+
+#endif /* __CVMX_SCRATCH_H__ */
diff --git a/arch/mips/include/asm/octeon/cvmx-sli-defs.h b/arch/mips/include/asm/octeon/cvmx-sli-defs.h
new file mode 100644
index 000000000..5ef6c3815
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-sli-defs.h
@@ -0,0 +1,129 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2017 Cavium, Inc.
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_SLI_DEFS_H__
+#define __CVMX_SLI_DEFS_H__
+
+#include <uapi/asm/bitfield.h>
+
+#define CVMX_SLI_PCIE_MSI_RCV CVMX_SLI_PCIE_MSI_RCV_FUNC()
+static inline uint64_t CVMX_SLI_PCIE_MSI_RCV_FUNC(void)
+{
+	switch (cvmx_get_octeon_family()) {
+	case OCTEON_CNF71XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN61XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN63XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN66XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN68XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN70XX & OCTEON_FAMILY_MASK:
+		return 0x0000000000003CB0ull;
+	case OCTEON_CNF75XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN73XX & OCTEON_FAMILY_MASK:
+	case OCTEON_CN78XX & OCTEON_FAMILY_MASK:
+		if (OCTEON_IS_MODEL(OCTEON_CN78XX_PASS1_X))
+			return 0x0000000000003CB0ull;
+		fallthrough;
+	default:
+		return 0x0000000000023CB0ull;
+	}
+}
+
+
+union cvmx_sli_ctl_portx {
+	uint64_t u64;
+	struct cvmx_sli_ctl_portx_s {
+		__BITFIELD_FIELD(uint64_t reserved_22_63:42,
+		__BITFIELD_FIELD(uint64_t intd:1,
+		__BITFIELD_FIELD(uint64_t intc:1,
+		__BITFIELD_FIELD(uint64_t intb:1,
+		__BITFIELD_FIELD(uint64_t inta:1,
+		__BITFIELD_FIELD(uint64_t dis_port:1,
+		__BITFIELD_FIELD(uint64_t waitl_com:1,
+		__BITFIELD_FIELD(uint64_t intd_map:2,
+		__BITFIELD_FIELD(uint64_t intc_map:2,
+		__BITFIELD_FIELD(uint64_t intb_map:2,
+		__BITFIELD_FIELD(uint64_t inta_map:2,
+		__BITFIELD_FIELD(uint64_t ctlp_ro:1,
+		__BITFIELD_FIELD(uint64_t reserved_6_6:1,
+		__BITFIELD_FIELD(uint64_t ptlp_ro:1,
+		__BITFIELD_FIELD(uint64_t reserved_1_4:4,
+		__BITFIELD_FIELD(uint64_t wait_com:1,
+		;))))))))))))))))
+	} s;
+};
+
+union cvmx_sli_mem_access_ctl {
+	uint64_t u64;
+	struct cvmx_sli_mem_access_ctl_s {
+		__BITFIELD_FIELD(uint64_t reserved_14_63:50,
+		__BITFIELD_FIELD(uint64_t max_word:4,
+		__BITFIELD_FIELD(uint64_t timer:10,
+		;)))
+	} s;
+};
+
+union cvmx_sli_s2m_portx_ctl {
+	uint64_t u64;
+	struct cvmx_sli_s2m_portx_ctl_s {
+		__BITFIELD_FIELD(uint64_t reserved_5_63:59,
+		__BITFIELD_FIELD(uint64_t wind_d:1,
+		__BITFIELD_FIELD(uint64_t bar0_d:1,
+		__BITFIELD_FIELD(uint64_t mrrs:3,
+		;))))
+	} s;
+};
+
+union cvmx_sli_mem_access_subidx {
+	uint64_t u64;
+	struct cvmx_sli_mem_access_subidx_s {
+		__BITFIELD_FIELD(uint64_t reserved_43_63:21,
+		__BITFIELD_FIELD(uint64_t zero:1,
+		__BITFIELD_FIELD(uint64_t port:3,
+		__BITFIELD_FIELD(uint64_t nmerge:1,
+		__BITFIELD_FIELD(uint64_t esr:2,
+		__BITFIELD_FIELD(uint64_t esw:2,
+		__BITFIELD_FIELD(uint64_t wtype:2,
+		__BITFIELD_FIELD(uint64_t rtype:2,
+		__BITFIELD_FIELD(uint64_t ba:30,
+		;)))))))))
+	} s;
+	struct cvmx_sli_mem_access_subidx_cn68xx {
+		__BITFIELD_FIELD(uint64_t reserved_43_63:21,
+		__BITFIELD_FIELD(uint64_t zero:1,
+		__BITFIELD_FIELD(uint64_t port:3,
+		__BITFIELD_FIELD(uint64_t nmerge:1,
+		__BITFIELD_FIELD(uint64_t esr:2,
+		__BITFIELD_FIELD(uint64_t esw:2,
+		__BITFIELD_FIELD(uint64_t wtype:2,
+		__BITFIELD_FIELD(uint64_t rtype:2,
+		__BITFIELD_FIELD(uint64_t ba:28,
+		__BITFIELD_FIELD(uint64_t reserved_0_1:2,
+		;))))))))))
+	} cn68xx;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-spi.h b/arch/mips/include/asm/octeon/cvmx-spi.h
new file mode 100644
index 000000000..d5038cc4b
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-spi.h
@@ -0,0 +1,269 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ *
+ * This file contains defines for the SPI interface
+ */
+#ifndef __CVMX_SPI_H__
+#define __CVMX_SPI_H__
+
+#include <asm/octeon/cvmx-gmxx-defs.h>
+
+/* CSR typedefs have been moved to cvmx-csr-*.h */
+
+typedef enum {
+	CVMX_SPI_MODE_UNKNOWN = 0,
+	CVMX_SPI_MODE_TX_HALFPLEX = 1,
+	CVMX_SPI_MODE_RX_HALFPLEX = 2,
+	CVMX_SPI_MODE_DUPLEX = 3
+} cvmx_spi_mode_t;
+
+/** Callbacks structure to customize SPI4 initialization sequence */
+typedef struct {
+    /** Called to reset SPI4 DLL */
+	int (*reset_cb) (int interface, cvmx_spi_mode_t mode);
+
+    /** Called to setup calendar */
+	int (*calendar_setup_cb) (int interface, cvmx_spi_mode_t mode,
+				  int num_ports);
+
+    /** Called for Tx and Rx clock detection */
+	int (*clock_detect_cb) (int interface, cvmx_spi_mode_t mode,
+				int timeout);
+
+    /** Called to perform link training */
+	int (*training_cb) (int interface, cvmx_spi_mode_t mode, int timeout);
+
+    /** Called for calendar data synchronization */
+	int (*calendar_sync_cb) (int interface, cvmx_spi_mode_t mode,
+				 int timeout);
+
+    /** Called when interface is up */
+	int (*interface_up_cb) (int interface, cvmx_spi_mode_t mode);
+
+} cvmx_spi_callbacks_t;
+
+/**
+ * Return true if the supplied interface is configured for SPI
+ *
+ * @interface: Interface to check
+ * Returns True if interface is SPI
+ */
+static inline int cvmx_spi_is_spi_interface(int interface)
+{
+	uint64_t gmxState = cvmx_read_csr(CVMX_GMXX_INF_MODE(interface));
+	return (gmxState & 0x2) && (gmxState & 0x1);
+}
+
+/**
+ * Initialize and start the SPI interface.
+ *
+ * @interface: The identifier of the packet interface to configure and
+ *		    use as a SPI interface.
+ * @mode:      The operating mode for the SPI interface. The interface
+ *		    can operate as a full duplex (both Tx and Rx data paths
+ *		    active) or as a halfplex (either the Tx data path is
+ *		    active or the Rx data path is active, but not both).
+ * @timeout:   Timeout to wait for clock synchronization in seconds
+ * @num_ports: Number of SPI ports to configure
+ *
+ * Returns Zero on success, negative of failure.
+ */
+extern int cvmx_spi_start_interface(int interface, cvmx_spi_mode_t mode,
+				    int timeout, int num_ports);
+
+/**
+ * This routine restarts the SPI interface after it has lost synchronization
+ * with its corespondant system.
+ *
+ * @interface: The identifier of the packet interface to configure and
+ *		    use as a SPI interface.
+ * @mode:      The operating mode for the SPI interface. The interface
+ *		    can operate as a full duplex (both Tx and Rx data paths
+ *		    active) or as a halfplex (either the Tx data path is
+ *		    active or the Rx data path is active, but not both).
+ * @timeout:   Timeout to wait for clock synchronization in seconds
+ * Returns Zero on success, negative of failure.
+ */
+extern int cvmx_spi_restart_interface(int interface, cvmx_spi_mode_t mode,
+				      int timeout);
+
+/**
+ * Return non-zero if the SPI interface has a SPI4000 attached
+ *
+ * @interface: SPI interface the SPI4000 is connected to
+ *
+ * Returns
+ */
+static inline int cvmx_spi4000_is_present(int interface)
+{
+	return 0;
+}
+
+/**
+ * Initialize the SPI4000 for use
+ *
+ * @interface: SPI interface the SPI4000 is connected to
+ */
+static inline int cvmx_spi4000_initialize(int interface)
+{
+	return 0;
+}
+
+/**
+ * Poll all the SPI4000 port and check its speed
+ *
+ * @interface: Interface the SPI4000 is on
+ * @port:      Port to poll (0-9)
+ * Returns Status of the port. 0=down. All other values the port is up.
+ */
+static inline union cvmx_gmxx_rxx_rx_inbnd cvmx_spi4000_check_speed(
+	int interface,
+	int port)
+{
+	union cvmx_gmxx_rxx_rx_inbnd r;
+	r.u64 = 0;
+	return r;
+}
+
+/**
+ * Get current SPI4 initialization callbacks
+ *
+ * @callbacks:	Pointer to the callbacks structure.to fill
+ *
+ * Returns Pointer to cvmx_spi_callbacks_t structure.
+ */
+extern void cvmx_spi_get_callbacks(cvmx_spi_callbacks_t *callbacks);
+
+/**
+ * Set new SPI4 initialization callbacks
+ *
+ * @new_callbacks:  Pointer to an updated callbacks structure.
+ */
+extern void cvmx_spi_set_callbacks(cvmx_spi_callbacks_t *new_callbacks);
+
+/**
+ * Callback to perform SPI4 reset
+ *
+ * @interface: The identifier of the packet interface to configure and
+ *		    use as a SPI interface.
+ * @mode:      The operating mode for the SPI interface. The interface
+ *		    can operate as a full duplex (both Tx and Rx data paths
+ *		    active) or as a halfplex (either the Tx data path is
+ *		    active or the Rx data path is active, but not both).
+ *
+ * Returns Zero on success, non-zero error code on failure (will cause
+ * SPI initialization to abort)
+ */
+extern int cvmx_spi_reset_cb(int interface, cvmx_spi_mode_t mode);
+
+/**
+ * Callback to setup calendar and miscellaneous settings before clock
+ * detection
+ *
+ * @interface: The identifier of the packet interface to configure and
+ *		    use as a SPI interface.
+ * @mode:      The operating mode for the SPI interface. The interface
+ *		    can operate as a full duplex (both Tx and Rx data paths
+ *		    active) or as a halfplex (either the Tx data path is
+ *		    active or the Rx data path is active, but not both).
+ * @num_ports: Number of ports to configure on SPI
+ *
+ * Returns Zero on success, non-zero error code on failure (will cause
+ * SPI initialization to abort)
+ */
+extern int cvmx_spi_calendar_setup_cb(int interface, cvmx_spi_mode_t mode,
+				      int num_ports);
+
+/**
+ * Callback to perform clock detection
+ *
+ * @interface: The identifier of the packet interface to configure and
+ *		    use as a SPI interface.
+ * @mode:      The operating mode for the SPI interface. The interface
+ *		    can operate as a full duplex (both Tx and Rx data paths
+ *		    active) or as a halfplex (either the Tx data path is
+ *		    active or the Rx data path is active, but not both).
+ * @timeout:   Timeout to wait for clock synchronization in seconds
+ *
+ * Returns Zero on success, non-zero error code on failure (will cause
+ * SPI initialization to abort)
+ */
+extern int cvmx_spi_clock_detect_cb(int interface, cvmx_spi_mode_t mode,
+				    int timeout);
+
+/**
+ * Callback to perform link training
+ *
+ * @interface: The identifier of the packet interface to configure and
+ *		    use as a SPI interface.
+ * @mode:      The operating mode for the SPI interface. The interface
+ *		    can operate as a full duplex (both Tx and Rx data paths
+ *		    active) or as a halfplex (either the Tx data path is
+ *		    active or the Rx data path is active, but not both).
+ * @timeout:   Timeout to wait for link to be trained (in seconds)
+ *
+ * Returns Zero on success, non-zero error code on failure (will cause
+ * SPI initialization to abort)
+ */
+extern int cvmx_spi_training_cb(int interface, cvmx_spi_mode_t mode,
+				int timeout);
+
+/**
+ * Callback to perform calendar data synchronization
+ *
+ * @interface: The identifier of the packet interface to configure and
+ *		    use as a SPI interface.
+ * @mode:      The operating mode for the SPI interface. The interface
+ *		    can operate as a full duplex (both Tx and Rx data paths
+ *		    active) or as a halfplex (either the Tx data path is
+ *		    active or the Rx data path is active, but not both).
+ * @timeout:   Timeout to wait for calendar data in seconds
+ *
+ * Returns Zero on success, non-zero error code on failure (will cause
+ * SPI initialization to abort)
+ */
+extern int cvmx_spi_calendar_sync_cb(int interface, cvmx_spi_mode_t mode,
+				     int timeout);
+
+/**
+ * Callback to handle interface up
+ *
+ * @interface: The identifier of the packet interface to configure and
+ *		    use as a SPI interface.
+ * @mode:      The operating mode for the SPI interface. The interface
+ *		    can operate as a full duplex (both Tx and Rx data paths
+ *		    active) or as a halfplex (either the Tx data path is
+ *		    active or the Rx data path is active, but not both).
+ *
+ * Returns Zero on success, non-zero error code on failure (will cause
+ * SPI initialization to abort)
+ */
+extern int cvmx_spi_interface_up_cb(int interface, cvmx_spi_mode_t mode);
+
+#endif /* __CVMX_SPI_H__ */
diff --git a/arch/mips/include/asm/octeon/cvmx-spinlock.h b/arch/mips/include/asm/octeon/cvmx-spinlock.h
new file mode 100644
index 000000000..4f09cff8b
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-spinlock.h
@@ -0,0 +1,232 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/**
+ * Implementation of spinlocks for Octeon CVMX.	 Although similar in
+ * function to Linux kernel spinlocks, they are not compatible.
+ * Octeon CVMX spinlocks are only used to synchronize with the boot
+ * monitor and other non-Linux programs running in the system.
+ */
+
+#ifndef __CVMX_SPINLOCK_H__
+#define __CVMX_SPINLOCK_H__
+
+#include <asm/octeon/cvmx-asm.h>
+
+/* Spinlocks for Octeon */
+
+/* define these to enable recursive spinlock debugging */
+/*#define CVMX_SPINLOCK_DEBUG */
+
+/**
+ * Spinlocks for Octeon CVMX
+ */
+typedef struct {
+	volatile uint32_t value;
+} cvmx_spinlock_t;
+
+/* note - macros not expanded in inline ASM, so values hardcoded */
+#define	 CVMX_SPINLOCK_UNLOCKED_VAL  0
+#define	 CVMX_SPINLOCK_LOCKED_VAL    1
+
+#define CVMX_SPINLOCK_UNLOCKED_INITIALIZER  {CVMX_SPINLOCK_UNLOCKED_VAL}
+
+/**
+ * Initialize a spinlock
+ *
+ * @lock:   Lock to initialize
+ */
+static inline void cvmx_spinlock_init(cvmx_spinlock_t *lock)
+{
+	lock->value = CVMX_SPINLOCK_UNLOCKED_VAL;
+}
+
+/**
+ * Return non-zero if the spinlock is currently locked
+ *
+ * @lock:   Lock to check
+ * Returns Non-zero if locked
+ */
+static inline int cvmx_spinlock_locked(cvmx_spinlock_t *lock)
+{
+	return lock->value != CVMX_SPINLOCK_UNLOCKED_VAL;
+}
+
+/**
+ * Releases lock
+ *
+ * @lock:   pointer to lock structure
+ */
+static inline void cvmx_spinlock_unlock(cvmx_spinlock_t *lock)
+{
+	CVMX_SYNCWS;
+	lock->value = 0;
+	CVMX_SYNCWS;
+}
+
+/**
+ * Attempts to take the lock, but does not spin if lock is not available.
+ * May take some time to acquire the lock even if it is available
+ * due to the ll/sc not succeeding.
+ *
+ * @lock:   pointer to lock structure
+ *
+ * Returns 0: lock successfully taken
+ *	   1: lock not taken, held by someone else
+ * These return values match the Linux semantics.
+ */
+
+static inline unsigned int cvmx_spinlock_trylock(cvmx_spinlock_t *lock)
+{
+	unsigned int tmp;
+
+	__asm__ __volatile__(".set noreorder	     \n"
+			     "1: ll   %[tmp], %[val] \n"
+			/* if lock held, fail immediately */
+			     "	 bnez %[tmp], 2f     \n"
+			     "	 li   %[tmp], 1	     \n"
+			     "	 sc   %[tmp], %[val] \n"
+			     "	 beqz %[tmp], 1b     \n"
+			     "	 li   %[tmp], 0	     \n"
+			     "2:		     \n"
+			     ".set reorder	     \n" :
+			[val] "+m"(lock->value), [tmp] "=&r"(tmp)
+			     : : "memory");
+
+	return tmp != 0;		/* normalize to 0 or 1 */
+}
+
+/**
+ * Gets lock, spins until lock is taken
+ *
+ * @lock:   pointer to lock structure
+ */
+static inline void cvmx_spinlock_lock(cvmx_spinlock_t *lock)
+{
+	unsigned int tmp;
+
+	__asm__ __volatile__(".set noreorder	     \n"
+			     "1: ll   %[tmp], %[val]  \n"
+			     "	 bnez %[tmp], 1b     \n"
+			     "	 li   %[tmp], 1	     \n"
+			     "	 sc   %[tmp], %[val] \n"
+			     "	 beqz %[tmp], 1b     \n"
+			     "	 nop		    \n"
+			     ".set reorder	     \n" :
+			[val] "+m"(lock->value), [tmp] "=&r"(tmp)
+			: : "memory");
+
+}
+
+/** ********************************************************************
+ * Bit spinlocks
+ * These spinlocks use a single bit (bit 31) of a 32 bit word for locking.
+ * The rest of the bits in the word are left undisturbed.  This enables more
+ * compact data structures as only 1 bit is consumed for the lock.
+ *
+ */
+
+/**
+ * Gets lock, spins until lock is taken
+ * Preserves the low 31 bits of the 32 bit
+ * word used for the lock.
+ *
+ *
+ * @word:  word to lock bit 31 of
+ */
+static inline void cvmx_spinlock_bit_lock(uint32_t *word)
+{
+	unsigned int tmp;
+	unsigned int sav;
+
+	__asm__ __volatile__(".set noreorder	     \n"
+			     ".set noat		     \n"
+			     "1: ll    %[tmp], %[val]  \n"
+			     "	 bbit1 %[tmp], 31, 1b	 \n"
+			     "	 li    $at, 1	   \n"
+			     "	 ins   %[tmp], $at, 31, 1  \n"
+			     "	 sc    %[tmp], %[val] \n"
+			     "	 beqz  %[tmp], 1b     \n"
+			     "	 nop		    \n"
+			     ".set at		   \n"
+			     ".set reorder	     \n" :
+			[val] "+m"(*word), [tmp] "=&r"(tmp), [sav] "=&r"(sav)
+			     : : "memory");
+
+}
+
+/**
+ * Attempts to get lock, returns immediately with success/failure
+ * Preserves the low 31 bits of the 32 bit
+ * word used for the lock.
+ *
+ *
+ * @word:  word to lock bit 31 of
+ * Returns 0: lock successfully taken
+ *	   1: lock not taken, held by someone else
+ * These return values match the Linux semantics.
+ */
+static inline unsigned int cvmx_spinlock_bit_trylock(uint32_t *word)
+{
+	unsigned int tmp;
+
+	__asm__ __volatile__(".set noreorder\n\t"
+			     ".set noat\n"
+			     "1: ll    %[tmp], %[val] \n"
+			/* if lock held, fail immediately */
+			     "	 bbit1 %[tmp], 31, 2f	  \n"
+			     "	 li    $at, 1	   \n"
+			     "	 ins   %[tmp], $at, 31, 1  \n"
+			     "	 sc    %[tmp], %[val] \n"
+			     "	 beqz  %[tmp], 1b     \n"
+			     "	 li    %[tmp], 0      \n"
+			     "2:		     \n"
+			     ".set at		   \n"
+			     ".set reorder	     \n" :
+			[val] "+m"(*word), [tmp] "=&r"(tmp)
+			: : "memory");
+
+	return tmp != 0;		/* normalize to 0 or 1 */
+}
+
+/**
+ * Releases bit lock
+ *
+ * Unconditionally clears bit 31 of the lock word.  Note that this is
+ * done non-atomically, as this implementation assumes that the rest
+ * of the bits in the word are protected by the lock.
+ *
+ * @word:  word to unlock bit 31 in
+ */
+static inline void cvmx_spinlock_bit_unlock(uint32_t *word)
+{
+	CVMX_SYNCWS;
+	*word &= ~(1UL << 31);
+	CVMX_SYNCWS;
+}
+
+#endif /* __CVMX_SPINLOCK_H__ */
diff --git a/arch/mips/include/asm/octeon/cvmx-spxx-defs.h b/arch/mips/include/asm/octeon/cvmx-spxx-defs.h
new file mode 100644
index 000000000..8471ed2de
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-spxx-defs.h
@@ -0,0 +1,446 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (C) 2003-2018 Cavium, Inc.
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_SPXX_DEFS_H__
+#define __CVMX_SPXX_DEFS_H__
+
+#define CVMX_SPXX_BCKPRS_CNT(block_id) (CVMX_ADD_IO_SEG(0x0001180090000340ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_SPXX_BIST_STAT(block_id) (CVMX_ADD_IO_SEG(0x00011800900007F8ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_SPXX_CLK_CTL(block_id) (CVMX_ADD_IO_SEG(0x0001180090000348ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_SPXX_CLK_STAT(block_id) (CVMX_ADD_IO_SEG(0x0001180090000350ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_SPXX_DBG_DESKEW_CTL(block_id) (CVMX_ADD_IO_SEG(0x0001180090000368ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_SPXX_DBG_DESKEW_STATE(block_id) (CVMX_ADD_IO_SEG(0x0001180090000370ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_SPXX_DRV_CTL(block_id) (CVMX_ADD_IO_SEG(0x0001180090000358ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_SPXX_ERR_CTL(block_id) (CVMX_ADD_IO_SEG(0x0001180090000320ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_SPXX_INT_DAT(block_id) (CVMX_ADD_IO_SEG(0x0001180090000318ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_SPXX_INT_MSK(block_id) (CVMX_ADD_IO_SEG(0x0001180090000308ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_SPXX_INT_REG(block_id) (CVMX_ADD_IO_SEG(0x0001180090000300ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_SPXX_INT_SYNC(block_id) (CVMX_ADD_IO_SEG(0x0001180090000310ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_SPXX_TPA_ACC(block_id) (CVMX_ADD_IO_SEG(0x0001180090000338ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_SPXX_TPA_MAX(block_id) (CVMX_ADD_IO_SEG(0x0001180090000330ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_SPXX_TPA_SEL(block_id) (CVMX_ADD_IO_SEG(0x0001180090000328ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_SPXX_TRN4_CTL(block_id) (CVMX_ADD_IO_SEG(0x0001180090000360ull) + ((block_id) & 1) * 0x8000000ull)
+
+void __cvmx_interrupt_spxx_int_msk_enable(int index);
+
+union cvmx_spxx_bckprs_cnt {
+	uint64_t u64;
+	struct cvmx_spxx_bckprs_cnt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t cnt:32;
+#else
+		uint64_t cnt:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_spxx_bist_stat {
+	uint64_t u64;
+	struct cvmx_spxx_bist_stat_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_3_63:61;
+		uint64_t stat2:1;
+		uint64_t stat1:1;
+		uint64_t stat0:1;
+#else
+		uint64_t stat0:1;
+		uint64_t stat1:1;
+		uint64_t stat2:1;
+		uint64_t reserved_3_63:61;
+#endif
+	} s;
+};
+
+union cvmx_spxx_clk_ctl {
+	uint64_t u64;
+	struct cvmx_spxx_clk_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_17_63:47;
+		uint64_t seetrn:1;
+		uint64_t reserved_12_15:4;
+		uint64_t clkdly:5;
+		uint64_t runbist:1;
+		uint64_t statdrv:1;
+		uint64_t statrcv:1;
+		uint64_t sndtrn:1;
+		uint64_t drptrn:1;
+		uint64_t rcvtrn:1;
+		uint64_t srxdlck:1;
+#else
+		uint64_t srxdlck:1;
+		uint64_t rcvtrn:1;
+		uint64_t drptrn:1;
+		uint64_t sndtrn:1;
+		uint64_t statrcv:1;
+		uint64_t statdrv:1;
+		uint64_t runbist:1;
+		uint64_t clkdly:5;
+		uint64_t reserved_12_15:4;
+		uint64_t seetrn:1;
+		uint64_t reserved_17_63:47;
+#endif
+	} s;
+};
+
+union cvmx_spxx_clk_stat {
+	uint64_t u64;
+	struct cvmx_spxx_clk_stat_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_11_63:53;
+		uint64_t stxcal:1;
+		uint64_t reserved_9_9:1;
+		uint64_t srxtrn:1;
+		uint64_t s4clk1:1;
+		uint64_t s4clk0:1;
+		uint64_t d4clk1:1;
+		uint64_t d4clk0:1;
+		uint64_t reserved_0_3:4;
+#else
+		uint64_t reserved_0_3:4;
+		uint64_t d4clk0:1;
+		uint64_t d4clk1:1;
+		uint64_t s4clk0:1;
+		uint64_t s4clk1:1;
+		uint64_t srxtrn:1;
+		uint64_t reserved_9_9:1;
+		uint64_t stxcal:1;
+		uint64_t reserved_11_63:53;
+#endif
+	} s;
+};
+
+union cvmx_spxx_dbg_deskew_ctl {
+	uint64_t u64;
+	struct cvmx_spxx_dbg_deskew_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_30_63:34;
+		uint64_t fallnop:1;
+		uint64_t fall8:1;
+		uint64_t reserved_26_27:2;
+		uint64_t sstep_go:1;
+		uint64_t sstep:1;
+		uint64_t reserved_22_23:2;
+		uint64_t clrdly:1;
+		uint64_t dec:1;
+		uint64_t inc:1;
+		uint64_t mux:1;
+		uint64_t offset:5;
+		uint64_t bitsel:5;
+		uint64_t offdly:6;
+		uint64_t dllfrc:1;
+		uint64_t dlldis:1;
+#else
+		uint64_t dlldis:1;
+		uint64_t dllfrc:1;
+		uint64_t offdly:6;
+		uint64_t bitsel:5;
+		uint64_t offset:5;
+		uint64_t mux:1;
+		uint64_t inc:1;
+		uint64_t dec:1;
+		uint64_t clrdly:1;
+		uint64_t reserved_22_23:2;
+		uint64_t sstep:1;
+		uint64_t sstep_go:1;
+		uint64_t reserved_26_27:2;
+		uint64_t fall8:1;
+		uint64_t fallnop:1;
+		uint64_t reserved_30_63:34;
+#endif
+	} s;
+};
+
+union cvmx_spxx_dbg_deskew_state {
+	uint64_t u64;
+	struct cvmx_spxx_dbg_deskew_state_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_9_63:55;
+		uint64_t testres:1;
+		uint64_t unxterm:1;
+		uint64_t muxsel:2;
+		uint64_t offset:5;
+#else
+		uint64_t offset:5;
+		uint64_t muxsel:2;
+		uint64_t unxterm:1;
+		uint64_t testres:1;
+		uint64_t reserved_9_63:55;
+#endif
+	} s;
+};
+
+union cvmx_spxx_drv_ctl {
+	uint64_t u64;
+	struct cvmx_spxx_drv_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_0_63:64;
+#else
+		uint64_t reserved_0_63:64;
+#endif
+	} s;
+	struct cvmx_spxx_drv_ctl_cn38xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t stx4ncmp:4;
+		uint64_t stx4pcmp:4;
+		uint64_t srx4cmp:8;
+#else
+		uint64_t srx4cmp:8;
+		uint64_t stx4pcmp:4;
+		uint64_t stx4ncmp:4;
+		uint64_t reserved_16_63:48;
+#endif
+	} cn38xx;
+	struct cvmx_spxx_drv_ctl_cn58xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_24_63:40;
+		uint64_t stx4ncmp:4;
+		uint64_t stx4pcmp:4;
+		uint64_t reserved_10_15:6;
+		uint64_t srx4cmp:10;
+#else
+		uint64_t srx4cmp:10;
+		uint64_t reserved_10_15:6;
+		uint64_t stx4pcmp:4;
+		uint64_t stx4ncmp:4;
+		uint64_t reserved_24_63:40;
+#endif
+	} cn58xx;
+};
+
+union cvmx_spxx_err_ctl {
+	uint64_t u64;
+	struct cvmx_spxx_err_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_9_63:55;
+		uint64_t prtnxa:1;
+		uint64_t dipcls:1;
+		uint64_t dippay:1;
+		uint64_t reserved_4_5:2;
+		uint64_t errcnt:4;
+#else
+		uint64_t errcnt:4;
+		uint64_t reserved_4_5:2;
+		uint64_t dippay:1;
+		uint64_t dipcls:1;
+		uint64_t prtnxa:1;
+		uint64_t reserved_9_63:55;
+#endif
+	} s;
+};
+
+union cvmx_spxx_int_dat {
+	uint64_t u64;
+	struct cvmx_spxx_int_dat_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t mul:1;
+		uint64_t reserved_14_30:17;
+		uint64_t calbnk:2;
+		uint64_t rsvop:4;
+		uint64_t prt:8;
+#else
+		uint64_t prt:8;
+		uint64_t rsvop:4;
+		uint64_t calbnk:2;
+		uint64_t reserved_14_30:17;
+		uint64_t mul:1;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_spxx_int_msk {
+	uint64_t u64;
+	struct cvmx_spxx_int_msk_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t calerr:1;
+		uint64_t syncerr:1;
+		uint64_t diperr:1;
+		uint64_t tpaovr:1;
+		uint64_t rsverr:1;
+		uint64_t drwnng:1;
+		uint64_t clserr:1;
+		uint64_t spiovr:1;
+		uint64_t reserved_2_3:2;
+		uint64_t abnorm:1;
+		uint64_t prtnxa:1;
+#else
+		uint64_t prtnxa:1;
+		uint64_t abnorm:1;
+		uint64_t reserved_2_3:2;
+		uint64_t spiovr:1;
+		uint64_t clserr:1;
+		uint64_t drwnng:1;
+		uint64_t rsverr:1;
+		uint64_t tpaovr:1;
+		uint64_t diperr:1;
+		uint64_t syncerr:1;
+		uint64_t calerr:1;
+		uint64_t reserved_12_63:52;
+#endif
+	} s;
+};
+
+union cvmx_spxx_int_reg {
+	uint64_t u64;
+	struct cvmx_spxx_int_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t spf:1;
+		uint64_t reserved_12_30:19;
+		uint64_t calerr:1;
+		uint64_t syncerr:1;
+		uint64_t diperr:1;
+		uint64_t tpaovr:1;
+		uint64_t rsverr:1;
+		uint64_t drwnng:1;
+		uint64_t clserr:1;
+		uint64_t spiovr:1;
+		uint64_t reserved_2_3:2;
+		uint64_t abnorm:1;
+		uint64_t prtnxa:1;
+#else
+		uint64_t prtnxa:1;
+		uint64_t abnorm:1;
+		uint64_t reserved_2_3:2;
+		uint64_t spiovr:1;
+		uint64_t clserr:1;
+		uint64_t drwnng:1;
+		uint64_t rsverr:1;
+		uint64_t tpaovr:1;
+		uint64_t diperr:1;
+		uint64_t syncerr:1;
+		uint64_t calerr:1;
+		uint64_t reserved_12_30:19;
+		uint64_t spf:1;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_spxx_int_sync {
+	uint64_t u64;
+	struct cvmx_spxx_int_sync_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_12_63:52;
+		uint64_t calerr:1;
+		uint64_t syncerr:1;
+		uint64_t diperr:1;
+		uint64_t tpaovr:1;
+		uint64_t rsverr:1;
+		uint64_t drwnng:1;
+		uint64_t clserr:1;
+		uint64_t spiovr:1;
+		uint64_t reserved_2_3:2;
+		uint64_t abnorm:1;
+		uint64_t prtnxa:1;
+#else
+		uint64_t prtnxa:1;
+		uint64_t abnorm:1;
+		uint64_t reserved_2_3:2;
+		uint64_t spiovr:1;
+		uint64_t clserr:1;
+		uint64_t drwnng:1;
+		uint64_t rsverr:1;
+		uint64_t tpaovr:1;
+		uint64_t diperr:1;
+		uint64_t syncerr:1;
+		uint64_t calerr:1;
+		uint64_t reserved_12_63:52;
+#endif
+	} s;
+};
+
+union cvmx_spxx_tpa_acc {
+	uint64_t u64;
+	struct cvmx_spxx_tpa_acc_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t cnt:32;
+#else
+		uint64_t cnt:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_spxx_tpa_max {
+	uint64_t u64;
+	struct cvmx_spxx_tpa_max_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t max:32;
+#else
+		uint64_t max:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_spxx_tpa_sel {
+	uint64_t u64;
+	struct cvmx_spxx_tpa_sel_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t prtsel:4;
+#else
+		uint64_t prtsel:4;
+		uint64_t reserved_4_63:60;
+#endif
+	} s;
+};
+
+union cvmx_spxx_trn4_ctl {
+	uint64_t u64;
+	struct cvmx_spxx_trn4_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_13_63:51;
+		uint64_t trntest:1;
+		uint64_t jitter:3;
+		uint64_t clr_boot:1;
+		uint64_t set_boot:1;
+		uint64_t maxdist:5;
+		uint64_t macro_en:1;
+		uint64_t mux_en:1;
+#else
+		uint64_t mux_en:1;
+		uint64_t macro_en:1;
+		uint64_t maxdist:5;
+		uint64_t set_boot:1;
+		uint64_t clr_boot:1;
+		uint64_t jitter:3;
+		uint64_t trntest:1;
+		uint64_t reserved_13_63:51;
+#endif
+	} s;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-sriox-defs.h b/arch/mips/include/asm/octeon/cvmx-sriox-defs.h
new file mode 100644
index 000000000..34d0fadb5
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-sriox-defs.h
@@ -0,0 +1,1614 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2012 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_SRIOX_DEFS_H__
+#define __CVMX_SRIOX_DEFS_H__
+
+#define CVMX_SRIOX_ACC_CTRL(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000148ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_ASMBLY_ID(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000200ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_ASMBLY_INFO(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000208ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_BELL_RESP_CTRL(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000310ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_BIST_STATUS(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000108ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_IMSG_CTRL(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000508ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_IMSG_INST_HDRX(offset, block_id) (CVMX_ADD_IO_SEG(0x00011800C8000510ull) + (((offset) & 1) + ((block_id) & 3) * 0x200000ull) * 8)
+#define CVMX_SRIOX_IMSG_QOS_GRPX(offset, block_id) (CVMX_ADD_IO_SEG(0x00011800C8000600ull) + (((offset) & 31) + ((block_id) & 3) * 0x200000ull) * 8)
+#define CVMX_SRIOX_IMSG_STATUSX(offset, block_id) (CVMX_ADD_IO_SEG(0x00011800C8000700ull) + (((offset) & 31) + ((block_id) & 3) * 0x200000ull) * 8)
+#define CVMX_SRIOX_IMSG_VPORT_THR(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000500ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_IMSG_VPORT_THR2(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000528ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_INT2_ENABLE(block_id) (CVMX_ADD_IO_SEG(0x00011800C80003E0ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_INT2_REG(block_id) (CVMX_ADD_IO_SEG(0x00011800C80003E8ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_INT_ENABLE(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000110ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_INT_INFO0(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000120ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_INT_INFO1(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000128ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_INT_INFO2(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000130ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_INT_INFO3(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000138ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_INT_REG(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000118ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_IP_FEATURE(block_id) (CVMX_ADD_IO_SEG(0x00011800C80003F8ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_MAC_BUFFERS(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000390ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_MAINT_OP(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000158ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_MAINT_RD_DATA(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000160ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_MCE_TX_CTL(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000240ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_MEM_OP_CTRL(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000168ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_OMSG_CTRLX(offset, block_id) (CVMX_ADD_IO_SEG(0x00011800C8000488ull) + (((offset) & 1) + ((block_id) & 3) * 0x40000ull) * 64)
+#define CVMX_SRIOX_OMSG_DONE_COUNTSX(offset, block_id) (CVMX_ADD_IO_SEG(0x00011800C80004B0ull) + (((offset) & 1) + ((block_id) & 3) * 0x40000ull) * 64)
+#define CVMX_SRIOX_OMSG_FMP_MRX(offset, block_id) (CVMX_ADD_IO_SEG(0x00011800C8000498ull) + (((offset) & 1) + ((block_id) & 3) * 0x40000ull) * 64)
+#define CVMX_SRIOX_OMSG_NMP_MRX(offset, block_id) (CVMX_ADD_IO_SEG(0x00011800C80004A0ull) + (((offset) & 1) + ((block_id) & 3) * 0x40000ull) * 64)
+#define CVMX_SRIOX_OMSG_PORTX(offset, block_id) (CVMX_ADD_IO_SEG(0x00011800C8000480ull) + (((offset) & 1) + ((block_id) & 3) * 0x40000ull) * 64)
+#define CVMX_SRIOX_OMSG_SILO_THR(block_id) (CVMX_ADD_IO_SEG(0x00011800C80004F8ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_OMSG_SP_MRX(offset, block_id) (CVMX_ADD_IO_SEG(0x00011800C8000490ull) + (((offset) & 1) + ((block_id) & 3) * 0x40000ull) * 64)
+#define CVMX_SRIOX_PRIOX_IN_USE(offset, block_id) (CVMX_ADD_IO_SEG(0x00011800C80003C0ull) + (((offset) & 3) + ((block_id) & 3) * 0x200000ull) * 8)
+#define CVMX_SRIOX_RX_BELL(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000308ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_RX_BELL_SEQ(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000300ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_RX_STATUS(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000380ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_S2M_TYPEX(offset, block_id) (CVMX_ADD_IO_SEG(0x00011800C8000180ull) + (((offset) & 15) + ((block_id) & 3) * 0x200000ull) * 8)
+#define CVMX_SRIOX_SEQ(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000278ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_STATUS_REG(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000100ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_TAG_CTRL(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000178ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_TLP_CREDITS(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000150ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_TX_BELL(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000280ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_TX_BELL_INFO(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000288ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_TX_CTRL(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000170ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_TX_EMPHASIS(block_id) (CVMX_ADD_IO_SEG(0x00011800C80003F0ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_TX_STATUS(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000388ull) + ((block_id) & 3) * 0x1000000ull)
+#define CVMX_SRIOX_WR_DONE_COUNTS(block_id) (CVMX_ADD_IO_SEG(0x00011800C8000340ull) + ((block_id) & 3) * 0x1000000ull)
+
+union cvmx_sriox_acc_ctrl {
+	uint64_t u64;
+	struct cvmx_sriox_acc_ctrl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_7_63:57;
+		uint64_t deny_adr2:1;
+		uint64_t deny_adr1:1;
+		uint64_t deny_adr0:1;
+		uint64_t reserved_3_3:1;
+		uint64_t deny_bar2:1;
+		uint64_t deny_bar1:1;
+		uint64_t deny_bar0:1;
+#else
+		uint64_t deny_bar0:1;
+		uint64_t deny_bar1:1;
+		uint64_t deny_bar2:1;
+		uint64_t reserved_3_3:1;
+		uint64_t deny_adr0:1;
+		uint64_t deny_adr1:1;
+		uint64_t deny_adr2:1;
+		uint64_t reserved_7_63:57;
+#endif
+	} s;
+	struct cvmx_sriox_acc_ctrl_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_3_63:61;
+		uint64_t deny_bar2:1;
+		uint64_t deny_bar1:1;
+		uint64_t deny_bar0:1;
+#else
+		uint64_t deny_bar0:1;
+		uint64_t deny_bar1:1;
+		uint64_t deny_bar2:1;
+		uint64_t reserved_3_63:61;
+#endif
+	} cn63xx;
+};
+
+union cvmx_sriox_asmbly_id {
+	uint64_t u64;
+	struct cvmx_sriox_asmbly_id_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t assy_id:16;
+		uint64_t assy_ven:16;
+#else
+		uint64_t assy_ven:16;
+		uint64_t assy_id:16;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_sriox_asmbly_info {
+	uint64_t u64;
+	struct cvmx_sriox_asmbly_info_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t assy_rev:16;
+		uint64_t reserved_0_15:16;
+#else
+		uint64_t reserved_0_15:16;
+		uint64_t assy_rev:16;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_sriox_bell_resp_ctrl {
+	uint64_t u64;
+	struct cvmx_sriox_bell_resp_ctrl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t rp1_sid:1;
+		uint64_t rp0_sid:2;
+		uint64_t rp1_pid:1;
+		uint64_t rp0_pid:2;
+#else
+		uint64_t rp0_pid:2;
+		uint64_t rp1_pid:1;
+		uint64_t rp0_sid:2;
+		uint64_t rp1_sid:1;
+		uint64_t reserved_6_63:58;
+#endif
+	} s;
+};
+
+union cvmx_sriox_bist_status {
+	uint64_t u64;
+	struct cvmx_sriox_bist_status_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_45_63:19;
+		uint64_t lram:1;
+		uint64_t mram:2;
+		uint64_t cram:2;
+		uint64_t bell:2;
+		uint64_t otag:2;
+		uint64_t itag:1;
+		uint64_t ofree:1;
+		uint64_t rtn:2;
+		uint64_t obulk:4;
+		uint64_t optrs:4;
+		uint64_t oarb2:2;
+		uint64_t rxbuf2:2;
+		uint64_t oarb:2;
+		uint64_t ispf:1;
+		uint64_t ospf:1;
+		uint64_t txbuf:2;
+		uint64_t rxbuf:2;
+		uint64_t imsg:5;
+		uint64_t omsg:7;
+#else
+		uint64_t omsg:7;
+		uint64_t imsg:5;
+		uint64_t rxbuf:2;
+		uint64_t txbuf:2;
+		uint64_t ospf:1;
+		uint64_t ispf:1;
+		uint64_t oarb:2;
+		uint64_t rxbuf2:2;
+		uint64_t oarb2:2;
+		uint64_t optrs:4;
+		uint64_t obulk:4;
+		uint64_t rtn:2;
+		uint64_t ofree:1;
+		uint64_t itag:1;
+		uint64_t otag:2;
+		uint64_t bell:2;
+		uint64_t cram:2;
+		uint64_t mram:2;
+		uint64_t lram:1;
+		uint64_t reserved_45_63:19;
+#endif
+	} s;
+	struct cvmx_sriox_bist_status_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_44_63:20;
+		uint64_t mram:2;
+		uint64_t cram:2;
+		uint64_t bell:2;
+		uint64_t otag:2;
+		uint64_t itag:1;
+		uint64_t ofree:1;
+		uint64_t rtn:2;
+		uint64_t obulk:4;
+		uint64_t optrs:4;
+		uint64_t oarb2:2;
+		uint64_t rxbuf2:2;
+		uint64_t oarb:2;
+		uint64_t ispf:1;
+		uint64_t ospf:1;
+		uint64_t txbuf:2;
+		uint64_t rxbuf:2;
+		uint64_t imsg:5;
+		uint64_t omsg:7;
+#else
+		uint64_t omsg:7;
+		uint64_t imsg:5;
+		uint64_t rxbuf:2;
+		uint64_t txbuf:2;
+		uint64_t ospf:1;
+		uint64_t ispf:1;
+		uint64_t oarb:2;
+		uint64_t rxbuf2:2;
+		uint64_t oarb2:2;
+		uint64_t optrs:4;
+		uint64_t obulk:4;
+		uint64_t rtn:2;
+		uint64_t ofree:1;
+		uint64_t itag:1;
+		uint64_t otag:2;
+		uint64_t bell:2;
+		uint64_t cram:2;
+		uint64_t mram:2;
+		uint64_t reserved_44_63:20;
+#endif
+	} cn63xx;
+	struct cvmx_sriox_bist_status_cn63xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_44_63:20;
+		uint64_t mram:2;
+		uint64_t cram:2;
+		uint64_t bell:2;
+		uint64_t otag:2;
+		uint64_t itag:1;
+		uint64_t ofree:1;
+		uint64_t rtn:2;
+		uint64_t obulk:4;
+		uint64_t optrs:4;
+		uint64_t reserved_20_23:4;
+		uint64_t oarb:2;
+		uint64_t ispf:1;
+		uint64_t ospf:1;
+		uint64_t txbuf:2;
+		uint64_t rxbuf:2;
+		uint64_t imsg:5;
+		uint64_t omsg:7;
+#else
+		uint64_t omsg:7;
+		uint64_t imsg:5;
+		uint64_t rxbuf:2;
+		uint64_t txbuf:2;
+		uint64_t ospf:1;
+		uint64_t ispf:1;
+		uint64_t oarb:2;
+		uint64_t reserved_20_23:4;
+		uint64_t optrs:4;
+		uint64_t obulk:4;
+		uint64_t rtn:2;
+		uint64_t ofree:1;
+		uint64_t itag:1;
+		uint64_t otag:2;
+		uint64_t bell:2;
+		uint64_t cram:2;
+		uint64_t mram:2;
+		uint64_t reserved_44_63:20;
+#endif
+	} cn63xxp1;
+};
+
+union cvmx_sriox_imsg_ctrl {
+	uint64_t u64;
+	struct cvmx_sriox_imsg_ctrl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t to_mode:1;
+		uint64_t reserved_30_30:1;
+		uint64_t rsp_thr:6;
+		uint64_t reserved_22_23:2;
+		uint64_t rp1_sid:1;
+		uint64_t rp0_sid:2;
+		uint64_t rp1_pid:1;
+		uint64_t rp0_pid:2;
+		uint64_t reserved_15_15:1;
+		uint64_t prt_sel:3;
+		uint64_t lttr:4;
+		uint64_t prio:4;
+		uint64_t mbox:4;
+#else
+		uint64_t mbox:4;
+		uint64_t prio:4;
+		uint64_t lttr:4;
+		uint64_t prt_sel:3;
+		uint64_t reserved_15_15:1;
+		uint64_t rp0_pid:2;
+		uint64_t rp1_pid:1;
+		uint64_t rp0_sid:2;
+		uint64_t rp1_sid:1;
+		uint64_t reserved_22_23:2;
+		uint64_t rsp_thr:6;
+		uint64_t reserved_30_30:1;
+		uint64_t to_mode:1;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_sriox_imsg_inst_hdrx {
+	uint64_t u64;
+	struct cvmx_sriox_imsg_inst_hdrx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t r:1;
+		uint64_t reserved_58_62:5;
+		uint64_t pm:2;
+		uint64_t reserved_55_55:1;
+		uint64_t sl:7;
+		uint64_t reserved_46_47:2;
+		uint64_t nqos:1;
+		uint64_t ngrp:1;
+		uint64_t ntt:1;
+		uint64_t ntag:1;
+		uint64_t reserved_35_41:7;
+		uint64_t rs:1;
+		uint64_t tt:2;
+		uint64_t tag:32;
+#else
+		uint64_t tag:32;
+		uint64_t tt:2;
+		uint64_t rs:1;
+		uint64_t reserved_35_41:7;
+		uint64_t ntag:1;
+		uint64_t ntt:1;
+		uint64_t ngrp:1;
+		uint64_t nqos:1;
+		uint64_t reserved_46_47:2;
+		uint64_t sl:7;
+		uint64_t reserved_55_55:1;
+		uint64_t pm:2;
+		uint64_t reserved_58_62:5;
+		uint64_t r:1;
+#endif
+	} s;
+};
+
+union cvmx_sriox_imsg_qos_grpx {
+	uint64_t u64;
+	struct cvmx_sriox_imsg_qos_grpx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_63_63:1;
+		uint64_t qos7:3;
+		uint64_t grp7:4;
+		uint64_t reserved_55_55:1;
+		uint64_t qos6:3;
+		uint64_t grp6:4;
+		uint64_t reserved_47_47:1;
+		uint64_t qos5:3;
+		uint64_t grp5:4;
+		uint64_t reserved_39_39:1;
+		uint64_t qos4:3;
+		uint64_t grp4:4;
+		uint64_t reserved_31_31:1;
+		uint64_t qos3:3;
+		uint64_t grp3:4;
+		uint64_t reserved_23_23:1;
+		uint64_t qos2:3;
+		uint64_t grp2:4;
+		uint64_t reserved_15_15:1;
+		uint64_t qos1:3;
+		uint64_t grp1:4;
+		uint64_t reserved_7_7:1;
+		uint64_t qos0:3;
+		uint64_t grp0:4;
+#else
+		uint64_t grp0:4;
+		uint64_t qos0:3;
+		uint64_t reserved_7_7:1;
+		uint64_t grp1:4;
+		uint64_t qos1:3;
+		uint64_t reserved_15_15:1;
+		uint64_t grp2:4;
+		uint64_t qos2:3;
+		uint64_t reserved_23_23:1;
+		uint64_t grp3:4;
+		uint64_t qos3:3;
+		uint64_t reserved_31_31:1;
+		uint64_t grp4:4;
+		uint64_t qos4:3;
+		uint64_t reserved_39_39:1;
+		uint64_t grp5:4;
+		uint64_t qos5:3;
+		uint64_t reserved_47_47:1;
+		uint64_t grp6:4;
+		uint64_t qos6:3;
+		uint64_t reserved_55_55:1;
+		uint64_t grp7:4;
+		uint64_t qos7:3;
+		uint64_t reserved_63_63:1;
+#endif
+	} s;
+};
+
+union cvmx_sriox_imsg_statusx {
+	uint64_t u64;
+	struct cvmx_sriox_imsg_statusx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t val1:1;
+		uint64_t err1:1;
+		uint64_t toe1:1;
+		uint64_t toc1:1;
+		uint64_t prt1:1;
+		uint64_t reserved_58_58:1;
+		uint64_t tt1:1;
+		uint64_t dis1:1;
+		uint64_t seg1:4;
+		uint64_t mbox1:2;
+		uint64_t lttr1:2;
+		uint64_t sid1:16;
+		uint64_t val0:1;
+		uint64_t err0:1;
+		uint64_t toe0:1;
+		uint64_t toc0:1;
+		uint64_t prt0:1;
+		uint64_t reserved_26_26:1;
+		uint64_t tt0:1;
+		uint64_t dis0:1;
+		uint64_t seg0:4;
+		uint64_t mbox0:2;
+		uint64_t lttr0:2;
+		uint64_t sid0:16;
+#else
+		uint64_t sid0:16;
+		uint64_t lttr0:2;
+		uint64_t mbox0:2;
+		uint64_t seg0:4;
+		uint64_t dis0:1;
+		uint64_t tt0:1;
+		uint64_t reserved_26_26:1;
+		uint64_t prt0:1;
+		uint64_t toc0:1;
+		uint64_t toe0:1;
+		uint64_t err0:1;
+		uint64_t val0:1;
+		uint64_t sid1:16;
+		uint64_t lttr1:2;
+		uint64_t mbox1:2;
+		uint64_t seg1:4;
+		uint64_t dis1:1;
+		uint64_t tt1:1;
+		uint64_t reserved_58_58:1;
+		uint64_t prt1:1;
+		uint64_t toc1:1;
+		uint64_t toe1:1;
+		uint64_t err1:1;
+		uint64_t val1:1;
+#endif
+	} s;
+};
+
+union cvmx_sriox_imsg_vport_thr {
+	uint64_t u64;
+	struct cvmx_sriox_imsg_vport_thr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_54_63:10;
+		uint64_t max_tot:6;
+		uint64_t reserved_46_47:2;
+		uint64_t max_s1:6;
+		uint64_t reserved_38_39:2;
+		uint64_t max_s0:6;
+		uint64_t sp_vport:1;
+		uint64_t reserved_20_30:11;
+		uint64_t buf_thr:4;
+		uint64_t reserved_14_15:2;
+		uint64_t max_p1:6;
+		uint64_t reserved_6_7:2;
+		uint64_t max_p0:6;
+#else
+		uint64_t max_p0:6;
+		uint64_t reserved_6_7:2;
+		uint64_t max_p1:6;
+		uint64_t reserved_14_15:2;
+		uint64_t buf_thr:4;
+		uint64_t reserved_20_30:11;
+		uint64_t sp_vport:1;
+		uint64_t max_s0:6;
+		uint64_t reserved_38_39:2;
+		uint64_t max_s1:6;
+		uint64_t reserved_46_47:2;
+		uint64_t max_tot:6;
+		uint64_t reserved_54_63:10;
+#endif
+	} s;
+};
+
+union cvmx_sriox_imsg_vport_thr2 {
+	uint64_t u64;
+	struct cvmx_sriox_imsg_vport_thr2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_46_63:18;
+		uint64_t max_s3:6;
+		uint64_t reserved_38_39:2;
+		uint64_t max_s2:6;
+		uint64_t reserved_0_31:32;
+#else
+		uint64_t reserved_0_31:32;
+		uint64_t max_s2:6;
+		uint64_t reserved_38_39:2;
+		uint64_t max_s3:6;
+		uint64_t reserved_46_63:18;
+#endif
+	} s;
+};
+
+union cvmx_sriox_int2_enable {
+	uint64_t u64;
+	struct cvmx_sriox_int2_enable_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t pko_rst:1;
+#else
+		uint64_t pko_rst:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_sriox_int2_reg {
+	uint64_t u64;
+	struct cvmx_sriox_int2_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t int_sum:1;
+		uint64_t reserved_1_30:30;
+		uint64_t pko_rst:1;
+#else
+		uint64_t pko_rst:1;
+		uint64_t reserved_1_30:30;
+		uint64_t int_sum:1;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_sriox_int_enable {
+	uint64_t u64;
+	struct cvmx_sriox_int_enable_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_27_63:37;
+		uint64_t zero_pkt:1;
+		uint64_t ttl_tout:1;
+		uint64_t fail:1;
+		uint64_t degrade:1;
+		uint64_t mac_buf:1;
+		uint64_t f_error:1;
+		uint64_t rtry_err:1;
+		uint64_t pko_err:1;
+		uint64_t omsg_err:1;
+		uint64_t omsg1:1;
+		uint64_t omsg0:1;
+		uint64_t link_up:1;
+		uint64_t link_dwn:1;
+		uint64_t phy_erb:1;
+		uint64_t log_erb:1;
+		uint64_t soft_rx:1;
+		uint64_t soft_tx:1;
+		uint64_t mce_rx:1;
+		uint64_t mce_tx:1;
+		uint64_t wr_done:1;
+		uint64_t sli_err:1;
+		uint64_t deny_wr:1;
+		uint64_t bar_err:1;
+		uint64_t maint_op:1;
+		uint64_t rxbell:1;
+		uint64_t bell_err:1;
+		uint64_t txbell:1;
+#else
+		uint64_t txbell:1;
+		uint64_t bell_err:1;
+		uint64_t rxbell:1;
+		uint64_t maint_op:1;
+		uint64_t bar_err:1;
+		uint64_t deny_wr:1;
+		uint64_t sli_err:1;
+		uint64_t wr_done:1;
+		uint64_t mce_tx:1;
+		uint64_t mce_rx:1;
+		uint64_t soft_tx:1;
+		uint64_t soft_rx:1;
+		uint64_t log_erb:1;
+		uint64_t phy_erb:1;
+		uint64_t link_dwn:1;
+		uint64_t link_up:1;
+		uint64_t omsg0:1;
+		uint64_t omsg1:1;
+		uint64_t omsg_err:1;
+		uint64_t pko_err:1;
+		uint64_t rtry_err:1;
+		uint64_t f_error:1;
+		uint64_t mac_buf:1;
+		uint64_t degrade:1;
+		uint64_t fail:1;
+		uint64_t ttl_tout:1;
+		uint64_t zero_pkt:1;
+		uint64_t reserved_27_63:37;
+#endif
+	} s;
+	struct cvmx_sriox_int_enable_cn63xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_22_63:42;
+		uint64_t f_error:1;
+		uint64_t rtry_err:1;
+		uint64_t pko_err:1;
+		uint64_t omsg_err:1;
+		uint64_t omsg1:1;
+		uint64_t omsg0:1;
+		uint64_t link_up:1;
+		uint64_t link_dwn:1;
+		uint64_t phy_erb:1;
+		uint64_t log_erb:1;
+		uint64_t soft_rx:1;
+		uint64_t soft_tx:1;
+		uint64_t mce_rx:1;
+		uint64_t mce_tx:1;
+		uint64_t wr_done:1;
+		uint64_t sli_err:1;
+		uint64_t deny_wr:1;
+		uint64_t bar_err:1;
+		uint64_t maint_op:1;
+		uint64_t rxbell:1;
+		uint64_t bell_err:1;
+		uint64_t txbell:1;
+#else
+		uint64_t txbell:1;
+		uint64_t bell_err:1;
+		uint64_t rxbell:1;
+		uint64_t maint_op:1;
+		uint64_t bar_err:1;
+		uint64_t deny_wr:1;
+		uint64_t sli_err:1;
+		uint64_t wr_done:1;
+		uint64_t mce_tx:1;
+		uint64_t mce_rx:1;
+		uint64_t soft_tx:1;
+		uint64_t soft_rx:1;
+		uint64_t log_erb:1;
+		uint64_t phy_erb:1;
+		uint64_t link_dwn:1;
+		uint64_t link_up:1;
+		uint64_t omsg0:1;
+		uint64_t omsg1:1;
+		uint64_t omsg_err:1;
+		uint64_t pko_err:1;
+		uint64_t rtry_err:1;
+		uint64_t f_error:1;
+		uint64_t reserved_22_63:42;
+#endif
+	} cn63xxp1;
+};
+
+union cvmx_sriox_int_info0 {
+	uint64_t u64;
+	struct cvmx_sriox_int_info0_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t cmd:4;
+		uint64_t type:4;
+		uint64_t tag:8;
+		uint64_t reserved_42_47:6;
+		uint64_t length:10;
+		uint64_t status:3;
+		uint64_t reserved_16_28:13;
+		uint64_t be0:8;
+		uint64_t be1:8;
+#else
+		uint64_t be1:8;
+		uint64_t be0:8;
+		uint64_t reserved_16_28:13;
+		uint64_t status:3;
+		uint64_t length:10;
+		uint64_t reserved_42_47:6;
+		uint64_t tag:8;
+		uint64_t type:4;
+		uint64_t cmd:4;
+#endif
+	} s;
+};
+
+union cvmx_sriox_int_info1 {
+	uint64_t u64;
+	struct cvmx_sriox_int_info1_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t info1:64;
+#else
+		uint64_t info1:64;
+#endif
+	} s;
+};
+
+union cvmx_sriox_int_info2 {
+	uint64_t u64;
+	struct cvmx_sriox_int_info2_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t prio:2;
+		uint64_t tt:1;
+		uint64_t sis:1;
+		uint64_t ssize:4;
+		uint64_t did:16;
+		uint64_t xmbox:4;
+		uint64_t mbox:2;
+		uint64_t letter:2;
+		uint64_t rsrvd:30;
+		uint64_t lns:1;
+		uint64_t intr:1;
+#else
+		uint64_t intr:1;
+		uint64_t lns:1;
+		uint64_t rsrvd:30;
+		uint64_t letter:2;
+		uint64_t mbox:2;
+		uint64_t xmbox:4;
+		uint64_t did:16;
+		uint64_t ssize:4;
+		uint64_t sis:1;
+		uint64_t tt:1;
+		uint64_t prio:2;
+#endif
+	} s;
+};
+
+union cvmx_sriox_int_info3 {
+	uint64_t u64;
+	struct cvmx_sriox_int_info3_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t prio:2;
+		uint64_t tt:2;
+		uint64_t type:4;
+		uint64_t other:48;
+		uint64_t reserved_0_7:8;
+#else
+		uint64_t reserved_0_7:8;
+		uint64_t other:48;
+		uint64_t type:4;
+		uint64_t tt:2;
+		uint64_t prio:2;
+#endif
+	} s;
+};
+
+union cvmx_sriox_int_reg {
+	uint64_t u64;
+	struct cvmx_sriox_int_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t int2_sum:1;
+		uint64_t reserved_27_30:4;
+		uint64_t zero_pkt:1;
+		uint64_t ttl_tout:1;
+		uint64_t fail:1;
+		uint64_t degrad:1;
+		uint64_t mac_buf:1;
+		uint64_t f_error:1;
+		uint64_t rtry_err:1;
+		uint64_t pko_err:1;
+		uint64_t omsg_err:1;
+		uint64_t omsg1:1;
+		uint64_t omsg0:1;
+		uint64_t link_up:1;
+		uint64_t link_dwn:1;
+		uint64_t phy_erb:1;
+		uint64_t log_erb:1;
+		uint64_t soft_rx:1;
+		uint64_t soft_tx:1;
+		uint64_t mce_rx:1;
+		uint64_t mce_tx:1;
+		uint64_t wr_done:1;
+		uint64_t sli_err:1;
+		uint64_t deny_wr:1;
+		uint64_t bar_err:1;
+		uint64_t maint_op:1;
+		uint64_t rxbell:1;
+		uint64_t bell_err:1;
+		uint64_t txbell:1;
+#else
+		uint64_t txbell:1;
+		uint64_t bell_err:1;
+		uint64_t rxbell:1;
+		uint64_t maint_op:1;
+		uint64_t bar_err:1;
+		uint64_t deny_wr:1;
+		uint64_t sli_err:1;
+		uint64_t wr_done:1;
+		uint64_t mce_tx:1;
+		uint64_t mce_rx:1;
+		uint64_t soft_tx:1;
+		uint64_t soft_rx:1;
+		uint64_t log_erb:1;
+		uint64_t phy_erb:1;
+		uint64_t link_dwn:1;
+		uint64_t link_up:1;
+		uint64_t omsg0:1;
+		uint64_t omsg1:1;
+		uint64_t omsg_err:1;
+		uint64_t pko_err:1;
+		uint64_t rtry_err:1;
+		uint64_t f_error:1;
+		uint64_t mac_buf:1;
+		uint64_t degrad:1;
+		uint64_t fail:1;
+		uint64_t ttl_tout:1;
+		uint64_t zero_pkt:1;
+		uint64_t reserved_27_30:4;
+		uint64_t int2_sum:1;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+	struct cvmx_sriox_int_reg_cn63xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_22_63:42;
+		uint64_t f_error:1;
+		uint64_t rtry_err:1;
+		uint64_t pko_err:1;
+		uint64_t omsg_err:1;
+		uint64_t omsg1:1;
+		uint64_t omsg0:1;
+		uint64_t link_up:1;
+		uint64_t link_dwn:1;
+		uint64_t phy_erb:1;
+		uint64_t log_erb:1;
+		uint64_t soft_rx:1;
+		uint64_t soft_tx:1;
+		uint64_t mce_rx:1;
+		uint64_t mce_tx:1;
+		uint64_t wr_done:1;
+		uint64_t sli_err:1;
+		uint64_t deny_wr:1;
+		uint64_t bar_err:1;
+		uint64_t maint_op:1;
+		uint64_t rxbell:1;
+		uint64_t bell_err:1;
+		uint64_t txbell:1;
+#else
+		uint64_t txbell:1;
+		uint64_t bell_err:1;
+		uint64_t rxbell:1;
+		uint64_t maint_op:1;
+		uint64_t bar_err:1;
+		uint64_t deny_wr:1;
+		uint64_t sli_err:1;
+		uint64_t wr_done:1;
+		uint64_t mce_tx:1;
+		uint64_t mce_rx:1;
+		uint64_t soft_tx:1;
+		uint64_t soft_rx:1;
+		uint64_t log_erb:1;
+		uint64_t phy_erb:1;
+		uint64_t link_dwn:1;
+		uint64_t link_up:1;
+		uint64_t omsg0:1;
+		uint64_t omsg1:1;
+		uint64_t omsg_err:1;
+		uint64_t pko_err:1;
+		uint64_t rtry_err:1;
+		uint64_t f_error:1;
+		uint64_t reserved_22_63:42;
+#endif
+	} cn63xxp1;
+};
+
+union cvmx_sriox_ip_feature {
+	uint64_t u64;
+	struct cvmx_sriox_ip_feature_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t ops:32;
+		uint64_t reserved_15_31:17;
+		uint64_t no_vmin:1;
+		uint64_t a66:1;
+		uint64_t a50:1;
+		uint64_t reserved_11_11:1;
+		uint64_t tx_flow:1;
+		uint64_t pt_width:2;
+		uint64_t tx_pol:4;
+		uint64_t rx_pol:4;
+#else
+		uint64_t rx_pol:4;
+		uint64_t tx_pol:4;
+		uint64_t pt_width:2;
+		uint64_t tx_flow:1;
+		uint64_t reserved_11_11:1;
+		uint64_t a50:1;
+		uint64_t a66:1;
+		uint64_t no_vmin:1;
+		uint64_t reserved_15_31:17;
+		uint64_t ops:32;
+#endif
+	} s;
+	struct cvmx_sriox_ip_feature_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t ops:32;
+		uint64_t reserved_14_31:18;
+		uint64_t a66:1;
+		uint64_t a50:1;
+		uint64_t reserved_11_11:1;
+		uint64_t tx_flow:1;
+		uint64_t pt_width:2;
+		uint64_t tx_pol:4;
+		uint64_t rx_pol:4;
+#else
+		uint64_t rx_pol:4;
+		uint64_t tx_pol:4;
+		uint64_t pt_width:2;
+		uint64_t tx_flow:1;
+		uint64_t reserved_11_11:1;
+		uint64_t a50:1;
+		uint64_t a66:1;
+		uint64_t reserved_14_31:18;
+		uint64_t ops:32;
+#endif
+	} cn63xx;
+};
+
+union cvmx_sriox_mac_buffers {
+	uint64_t u64;
+	struct cvmx_sriox_mac_buffers_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_56_63:8;
+		uint64_t tx_enb:8;
+		uint64_t reserved_44_47:4;
+		uint64_t tx_inuse:4;
+		uint64_t tx_stat:8;
+		uint64_t reserved_24_31:8;
+		uint64_t rx_enb:8;
+		uint64_t reserved_12_15:4;
+		uint64_t rx_inuse:4;
+		uint64_t rx_stat:8;
+#else
+		uint64_t rx_stat:8;
+		uint64_t rx_inuse:4;
+		uint64_t reserved_12_15:4;
+		uint64_t rx_enb:8;
+		uint64_t reserved_24_31:8;
+		uint64_t tx_stat:8;
+		uint64_t tx_inuse:4;
+		uint64_t reserved_44_47:4;
+		uint64_t tx_enb:8;
+		uint64_t reserved_56_63:8;
+#endif
+	} s;
+};
+
+union cvmx_sriox_maint_op {
+	uint64_t u64;
+	struct cvmx_sriox_maint_op_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t wr_data:32;
+		uint64_t reserved_27_31:5;
+		uint64_t fail:1;
+		uint64_t pending:1;
+		uint64_t op:1;
+		uint64_t addr:24;
+#else
+		uint64_t addr:24;
+		uint64_t op:1;
+		uint64_t pending:1;
+		uint64_t fail:1;
+		uint64_t reserved_27_31:5;
+		uint64_t wr_data:32;
+#endif
+	} s;
+};
+
+union cvmx_sriox_maint_rd_data {
+	uint64_t u64;
+	struct cvmx_sriox_maint_rd_data_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_33_63:31;
+		uint64_t valid:1;
+		uint64_t rd_data:32;
+#else
+		uint64_t rd_data:32;
+		uint64_t valid:1;
+		uint64_t reserved_33_63:31;
+#endif
+	} s;
+};
+
+union cvmx_sriox_mce_tx_ctl {
+	uint64_t u64;
+	struct cvmx_sriox_mce_tx_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t mce:1;
+#else
+		uint64_t mce:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_sriox_mem_op_ctrl {
+	uint64_t u64;
+	struct cvmx_sriox_mem_op_ctrl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t rr_ro:1;
+		uint64_t w_ro:1;
+		uint64_t reserved_6_7:2;
+		uint64_t rp1_sid:1;
+		uint64_t rp0_sid:2;
+		uint64_t rp1_pid:1;
+		uint64_t rp0_pid:2;
+#else
+		uint64_t rp0_pid:2;
+		uint64_t rp1_pid:1;
+		uint64_t rp0_sid:2;
+		uint64_t rp1_sid:1;
+		uint64_t reserved_6_7:2;
+		uint64_t w_ro:1;
+		uint64_t rr_ro:1;
+		uint64_t reserved_10_63:54;
+#endif
+	} s;
+};
+
+union cvmx_sriox_omsg_ctrlx {
+	uint64_t u64;
+	struct cvmx_sriox_omsg_ctrlx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t testmode:1;
+		uint64_t reserved_37_62:26;
+		uint64_t silo_max:5;
+		uint64_t rtry_thr:16;
+		uint64_t rtry_en:1;
+		uint64_t reserved_11_14:4;
+		uint64_t idm_tt:1;
+		uint64_t idm_sis:1;
+		uint64_t idm_did:1;
+		uint64_t lttr_sp:4;
+		uint64_t lttr_mp:4;
+#else
+		uint64_t lttr_mp:4;
+		uint64_t lttr_sp:4;
+		uint64_t idm_did:1;
+		uint64_t idm_sis:1;
+		uint64_t idm_tt:1;
+		uint64_t reserved_11_14:4;
+		uint64_t rtry_en:1;
+		uint64_t rtry_thr:16;
+		uint64_t silo_max:5;
+		uint64_t reserved_37_62:26;
+		uint64_t testmode:1;
+#endif
+	} s;
+	struct cvmx_sriox_omsg_ctrlx_cn63xxp1 {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t testmode:1;
+		uint64_t reserved_32_62:31;
+		uint64_t rtry_thr:16;
+		uint64_t rtry_en:1;
+		uint64_t reserved_11_14:4;
+		uint64_t idm_tt:1;
+		uint64_t idm_sis:1;
+		uint64_t idm_did:1;
+		uint64_t lttr_sp:4;
+		uint64_t lttr_mp:4;
+#else
+		uint64_t lttr_mp:4;
+		uint64_t lttr_sp:4;
+		uint64_t idm_did:1;
+		uint64_t idm_sis:1;
+		uint64_t idm_tt:1;
+		uint64_t reserved_11_14:4;
+		uint64_t rtry_en:1;
+		uint64_t rtry_thr:16;
+		uint64_t reserved_32_62:31;
+		uint64_t testmode:1;
+#endif
+	} cn63xxp1;
+};
+
+union cvmx_sriox_omsg_done_countsx {
+	uint64_t u64;
+	struct cvmx_sriox_omsg_done_countsx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t bad:16;
+		uint64_t good:16;
+#else
+		uint64_t good:16;
+		uint64_t bad:16;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_sriox_omsg_fmp_mrx {
+	uint64_t u64;
+	struct cvmx_sriox_omsg_fmp_mrx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_15_63:49;
+		uint64_t ctlr_sp:1;
+		uint64_t ctlr_fmp:1;
+		uint64_t ctlr_nmp:1;
+		uint64_t id_sp:1;
+		uint64_t id_fmp:1;
+		uint64_t id_nmp:1;
+		uint64_t id_psd:1;
+		uint64_t mbox_sp:1;
+		uint64_t mbox_fmp:1;
+		uint64_t mbox_nmp:1;
+		uint64_t mbox_psd:1;
+		uint64_t all_sp:1;
+		uint64_t all_fmp:1;
+		uint64_t all_nmp:1;
+		uint64_t all_psd:1;
+#else
+		uint64_t all_psd:1;
+		uint64_t all_nmp:1;
+		uint64_t all_fmp:1;
+		uint64_t all_sp:1;
+		uint64_t mbox_psd:1;
+		uint64_t mbox_nmp:1;
+		uint64_t mbox_fmp:1;
+		uint64_t mbox_sp:1;
+		uint64_t id_psd:1;
+		uint64_t id_nmp:1;
+		uint64_t id_fmp:1;
+		uint64_t id_sp:1;
+		uint64_t ctlr_nmp:1;
+		uint64_t ctlr_fmp:1;
+		uint64_t ctlr_sp:1;
+		uint64_t reserved_15_63:49;
+#endif
+	} s;
+};
+
+union cvmx_sriox_omsg_nmp_mrx {
+	uint64_t u64;
+	struct cvmx_sriox_omsg_nmp_mrx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_15_63:49;
+		uint64_t ctlr_sp:1;
+		uint64_t ctlr_fmp:1;
+		uint64_t ctlr_nmp:1;
+		uint64_t id_sp:1;
+		uint64_t id_fmp:1;
+		uint64_t id_nmp:1;
+		uint64_t reserved_8_8:1;
+		uint64_t mbox_sp:1;
+		uint64_t mbox_fmp:1;
+		uint64_t mbox_nmp:1;
+		uint64_t reserved_4_4:1;
+		uint64_t all_sp:1;
+		uint64_t all_fmp:1;
+		uint64_t all_nmp:1;
+		uint64_t reserved_0_0:1;
+#else
+		uint64_t reserved_0_0:1;
+		uint64_t all_nmp:1;
+		uint64_t all_fmp:1;
+		uint64_t all_sp:1;
+		uint64_t reserved_4_4:1;
+		uint64_t mbox_nmp:1;
+		uint64_t mbox_fmp:1;
+		uint64_t mbox_sp:1;
+		uint64_t reserved_8_8:1;
+		uint64_t id_nmp:1;
+		uint64_t id_fmp:1;
+		uint64_t id_sp:1;
+		uint64_t ctlr_nmp:1;
+		uint64_t ctlr_fmp:1;
+		uint64_t ctlr_sp:1;
+		uint64_t reserved_15_63:49;
+#endif
+	} s;
+};
+
+union cvmx_sriox_omsg_portx {
+	uint64_t u64;
+	struct cvmx_sriox_omsg_portx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t enable:1;
+		uint64_t reserved_3_30:28;
+		uint64_t port:3;
+#else
+		uint64_t port:3;
+		uint64_t reserved_3_30:28;
+		uint64_t enable:1;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+	struct cvmx_sriox_omsg_portx_cn63xx {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t enable:1;
+		uint64_t reserved_2_30:29;
+		uint64_t port:2;
+#else
+		uint64_t port:2;
+		uint64_t reserved_2_30:29;
+		uint64_t enable:1;
+		uint64_t reserved_32_63:32;
+#endif
+	} cn63xx;
+};
+
+union cvmx_sriox_omsg_silo_thr {
+	uint64_t u64;
+	struct cvmx_sriox_omsg_silo_thr_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_5_63:59;
+		uint64_t tot_silo:5;
+#else
+		uint64_t tot_silo:5;
+		uint64_t reserved_5_63:59;
+#endif
+	} s;
+};
+
+union cvmx_sriox_omsg_sp_mrx {
+	uint64_t u64;
+	struct cvmx_sriox_omsg_sp_mrx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t xmbox_sp:1;
+		uint64_t ctlr_sp:1;
+		uint64_t ctlr_fmp:1;
+		uint64_t ctlr_nmp:1;
+		uint64_t id_sp:1;
+		uint64_t id_fmp:1;
+		uint64_t id_nmp:1;
+		uint64_t id_psd:1;
+		uint64_t mbox_sp:1;
+		uint64_t mbox_fmp:1;
+		uint64_t mbox_nmp:1;
+		uint64_t mbox_psd:1;
+		uint64_t all_sp:1;
+		uint64_t all_fmp:1;
+		uint64_t all_nmp:1;
+		uint64_t all_psd:1;
+#else
+		uint64_t all_psd:1;
+		uint64_t all_nmp:1;
+		uint64_t all_fmp:1;
+		uint64_t all_sp:1;
+		uint64_t mbox_psd:1;
+		uint64_t mbox_nmp:1;
+		uint64_t mbox_fmp:1;
+		uint64_t mbox_sp:1;
+		uint64_t id_psd:1;
+		uint64_t id_nmp:1;
+		uint64_t id_fmp:1;
+		uint64_t id_sp:1;
+		uint64_t ctlr_nmp:1;
+		uint64_t ctlr_fmp:1;
+		uint64_t ctlr_sp:1;
+		uint64_t xmbox_sp:1;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_sriox_priox_in_use {
+	uint64_t u64;
+	struct cvmx_sriox_priox_in_use_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t end_cnt:16;
+		uint64_t start_cnt:16;
+#else
+		uint64_t start_cnt:16;
+		uint64_t end_cnt:16;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_sriox_rx_bell {
+	uint64_t u64;
+	struct cvmx_sriox_rx_bell_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t data:16;
+		uint64_t src_id:16;
+		uint64_t count:8;
+		uint64_t reserved_5_7:3;
+		uint64_t dest_id:1;
+		uint64_t id16:1;
+		uint64_t reserved_2_2:1;
+		uint64_t priority:2;
+#else
+		uint64_t priority:2;
+		uint64_t reserved_2_2:1;
+		uint64_t id16:1;
+		uint64_t dest_id:1;
+		uint64_t reserved_5_7:3;
+		uint64_t count:8;
+		uint64_t src_id:16;
+		uint64_t data:16;
+		uint64_t reserved_48_63:16;
+#endif
+	} s;
+};
+
+union cvmx_sriox_rx_bell_seq {
+	uint64_t u64;
+	struct cvmx_sriox_rx_bell_seq_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_40_63:24;
+		uint64_t count:8;
+		uint64_t seq:32;
+#else
+		uint64_t seq:32;
+		uint64_t count:8;
+		uint64_t reserved_40_63:24;
+#endif
+	} s;
+};
+
+union cvmx_sriox_rx_status {
+	uint64_t u64;
+	struct cvmx_sriox_rx_status_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t rtn_pr3:8;
+		uint64_t rtn_pr2:8;
+		uint64_t rtn_pr1:8;
+		uint64_t reserved_28_39:12;
+		uint64_t mbox:4;
+		uint64_t comp:8;
+		uint64_t reserved_13_15:3;
+		uint64_t n_post:5;
+		uint64_t post:8;
+#else
+		uint64_t post:8;
+		uint64_t n_post:5;
+		uint64_t reserved_13_15:3;
+		uint64_t comp:8;
+		uint64_t mbox:4;
+		uint64_t reserved_28_39:12;
+		uint64_t rtn_pr1:8;
+		uint64_t rtn_pr2:8;
+		uint64_t rtn_pr3:8;
+#endif
+	} s;
+};
+
+union cvmx_sriox_s2m_typex {
+	uint64_t u64;
+	struct cvmx_sriox_s2m_typex_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_19_63:45;
+		uint64_t wr_op:3;
+		uint64_t reserved_15_15:1;
+		uint64_t rd_op:3;
+		uint64_t wr_prior:2;
+		uint64_t rd_prior:2;
+		uint64_t reserved_6_7:2;
+		uint64_t src_id:1;
+		uint64_t id16:1;
+		uint64_t reserved_2_3:2;
+		uint64_t iaow_sel:2;
+#else
+		uint64_t iaow_sel:2;
+		uint64_t reserved_2_3:2;
+		uint64_t id16:1;
+		uint64_t src_id:1;
+		uint64_t reserved_6_7:2;
+		uint64_t rd_prior:2;
+		uint64_t wr_prior:2;
+		uint64_t rd_op:3;
+		uint64_t reserved_15_15:1;
+		uint64_t wr_op:3;
+		uint64_t reserved_19_63:45;
+#endif
+	} s;
+};
+
+union cvmx_sriox_seq {
+	uint64_t u64;
+	struct cvmx_sriox_seq_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t seq:32;
+#else
+		uint64_t seq:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_sriox_status_reg {
+	uint64_t u64;
+	struct cvmx_sriox_status_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_2_63:62;
+		uint64_t access:1;
+		uint64_t srio:1;
+#else
+		uint64_t srio:1;
+		uint64_t access:1;
+		uint64_t reserved_2_63:62;
+#endif
+	} s;
+};
+
+union cvmx_sriox_tag_ctrl {
+	uint64_t u64;
+	struct cvmx_sriox_tag_ctrl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_17_63:47;
+		uint64_t o_clr:1;
+		uint64_t reserved_13_15:3;
+		uint64_t otag:5;
+		uint64_t reserved_5_7:3;
+		uint64_t itag:5;
+#else
+		uint64_t itag:5;
+		uint64_t reserved_5_7:3;
+		uint64_t otag:5;
+		uint64_t reserved_13_15:3;
+		uint64_t o_clr:1;
+		uint64_t reserved_17_63:47;
+#endif
+	} s;
+};
+
+union cvmx_sriox_tlp_credits {
+	uint64_t u64;
+	struct cvmx_sriox_tlp_credits_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_28_63:36;
+		uint64_t mbox:4;
+		uint64_t comp:8;
+		uint64_t reserved_13_15:3;
+		uint64_t n_post:5;
+		uint64_t post:8;
+#else
+		uint64_t post:8;
+		uint64_t n_post:5;
+		uint64_t reserved_13_15:3;
+		uint64_t comp:8;
+		uint64_t mbox:4;
+		uint64_t reserved_28_63:36;
+#endif
+	} s;
+};
+
+union cvmx_sriox_tx_bell {
+	uint64_t u64;
+	struct cvmx_sriox_tx_bell_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t data:16;
+		uint64_t dest_id:16;
+		uint64_t reserved_9_15:7;
+		uint64_t pending:1;
+		uint64_t reserved_5_7:3;
+		uint64_t src_id:1;
+		uint64_t id16:1;
+		uint64_t reserved_2_2:1;
+		uint64_t priority:2;
+#else
+		uint64_t priority:2;
+		uint64_t reserved_2_2:1;
+		uint64_t id16:1;
+		uint64_t src_id:1;
+		uint64_t reserved_5_7:3;
+		uint64_t pending:1;
+		uint64_t reserved_9_15:7;
+		uint64_t dest_id:16;
+		uint64_t data:16;
+		uint64_t reserved_48_63:16;
+#endif
+	} s;
+};
+
+union cvmx_sriox_tx_bell_info {
+	uint64_t u64;
+	struct cvmx_sriox_tx_bell_info_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_48_63:16;
+		uint64_t data:16;
+		uint64_t dest_id:16;
+		uint64_t reserved_8_15:8;
+		uint64_t timeout:1;
+		uint64_t error:1;
+		uint64_t retry:1;
+		uint64_t src_id:1;
+		uint64_t id16:1;
+		uint64_t reserved_2_2:1;
+		uint64_t priority:2;
+#else
+		uint64_t priority:2;
+		uint64_t reserved_2_2:1;
+		uint64_t id16:1;
+		uint64_t src_id:1;
+		uint64_t retry:1;
+		uint64_t error:1;
+		uint64_t timeout:1;
+		uint64_t reserved_8_15:8;
+		uint64_t dest_id:16;
+		uint64_t data:16;
+		uint64_t reserved_48_63:16;
+#endif
+	} s;
+};
+
+union cvmx_sriox_tx_ctrl {
+	uint64_t u64;
+	struct cvmx_sriox_tx_ctrl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_53_63:11;
+		uint64_t tag_th2:5;
+		uint64_t reserved_45_47:3;
+		uint64_t tag_th1:5;
+		uint64_t reserved_37_39:3;
+		uint64_t tag_th0:5;
+		uint64_t reserved_20_31:12;
+		uint64_t tx_th2:4;
+		uint64_t reserved_12_15:4;
+		uint64_t tx_th1:4;
+		uint64_t reserved_4_7:4;
+		uint64_t tx_th0:4;
+#else
+		uint64_t tx_th0:4;
+		uint64_t reserved_4_7:4;
+		uint64_t tx_th1:4;
+		uint64_t reserved_12_15:4;
+		uint64_t tx_th2:4;
+		uint64_t reserved_20_31:12;
+		uint64_t tag_th0:5;
+		uint64_t reserved_37_39:3;
+		uint64_t tag_th1:5;
+		uint64_t reserved_45_47:3;
+		uint64_t tag_th2:5;
+		uint64_t reserved_53_63:11;
+#endif
+	} s;
+};
+
+union cvmx_sriox_tx_emphasis {
+	uint64_t u64;
+	struct cvmx_sriox_tx_emphasis_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t emph:4;
+#else
+		uint64_t emph:4;
+		uint64_t reserved_4_63:60;
+#endif
+	} s;
+};
+
+union cvmx_sriox_tx_status {
+	uint64_t u64;
+	struct cvmx_sriox_tx_status_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t s2m_pr3:8;
+		uint64_t s2m_pr2:8;
+		uint64_t s2m_pr1:8;
+		uint64_t s2m_pr0:8;
+#else
+		uint64_t s2m_pr0:8;
+		uint64_t s2m_pr1:8;
+		uint64_t s2m_pr2:8;
+		uint64_t s2m_pr3:8;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_sriox_wr_done_counts {
+	uint64_t u64;
+	struct cvmx_sriox_wr_done_counts_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t bad:16;
+		uint64_t good:16;
+#else
+		uint64_t good:16;
+		uint64_t bad:16;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-srxx-defs.h b/arch/mips/include/asm/octeon/cvmx-srxx-defs.h
new file mode 100644
index 000000000..76b2a42f5
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-srxx-defs.h
@@ -0,0 +1,140 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2012 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_SRXX_DEFS_H__
+#define __CVMX_SRXX_DEFS_H__
+
+#define CVMX_SRXX_COM_CTL(block_id) (CVMX_ADD_IO_SEG(0x0001180090000200ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_SRXX_IGN_RX_FULL(block_id) (CVMX_ADD_IO_SEG(0x0001180090000218ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_SRXX_SPI4_CALX(offset, block_id) (CVMX_ADD_IO_SEG(0x0001180090000000ull) + (((offset) & 31) + ((block_id) & 1) * 0x1000000ull) * 8)
+#define CVMX_SRXX_SPI4_STAT(block_id) (CVMX_ADD_IO_SEG(0x0001180090000208ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_SRXX_SW_TICK_CTL(block_id) (CVMX_ADD_IO_SEG(0x0001180090000220ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_SRXX_SW_TICK_DAT(block_id) (CVMX_ADD_IO_SEG(0x0001180090000228ull) + ((block_id) & 1) * 0x8000000ull)
+
+union cvmx_srxx_com_ctl {
+	uint64_t u64;
+	struct cvmx_srxx_com_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t prts:4;
+		uint64_t st_en:1;
+		uint64_t reserved_1_2:2;
+		uint64_t inf_en:1;
+#else
+		uint64_t inf_en:1;
+		uint64_t reserved_1_2:2;
+		uint64_t st_en:1;
+		uint64_t prts:4;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_srxx_ign_rx_full {
+	uint64_t u64;
+	struct cvmx_srxx_ign_rx_full_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t ignore:16;
+#else
+		uint64_t ignore:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_srxx_spi4_calx {
+	uint64_t u64;
+	struct cvmx_srxx_spi4_calx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_17_63:47;
+		uint64_t oddpar:1;
+		uint64_t prt3:4;
+		uint64_t prt2:4;
+		uint64_t prt1:4;
+		uint64_t prt0:4;
+#else
+		uint64_t prt0:4;
+		uint64_t prt1:4;
+		uint64_t prt2:4;
+		uint64_t prt3:4;
+		uint64_t oddpar:1;
+		uint64_t reserved_17_63:47;
+#endif
+	} s;
+};
+
+union cvmx_srxx_spi4_stat {
+	uint64_t u64;
+	struct cvmx_srxx_spi4_stat_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t m:8;
+		uint64_t reserved_7_7:1;
+		uint64_t len:7;
+#else
+		uint64_t len:7;
+		uint64_t reserved_7_7:1;
+		uint64_t m:8;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_srxx_sw_tick_ctl {
+	uint64_t u64;
+	struct cvmx_srxx_sw_tick_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_14_63:50;
+		uint64_t eop:1;
+		uint64_t sop:1;
+		uint64_t mod:4;
+		uint64_t opc:4;
+		uint64_t adr:4;
+#else
+		uint64_t adr:4;
+		uint64_t opc:4;
+		uint64_t mod:4;
+		uint64_t sop:1;
+		uint64_t eop:1;
+		uint64_t reserved_14_63:50;
+#endif
+	} s;
+};
+
+union cvmx_srxx_sw_tick_dat {
+	uint64_t u64;
+	struct cvmx_srxx_sw_tick_dat_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t dat:64;
+#else
+		uint64_t dat:64;
+#endif
+	} s;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-stxx-defs.h b/arch/mips/include/asm/octeon/cvmx-stxx-defs.h
new file mode 100644
index 000000000..f49d82145
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-stxx-defs.h
@@ -0,0 +1,330 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (C) 2003-2018 Cavium, Inc.
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_STXX_DEFS_H__
+#define __CVMX_STXX_DEFS_H__
+
+#define CVMX_STXX_ARB_CTL(block_id) (CVMX_ADD_IO_SEG(0x0001180090000608ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_STXX_BCKPRS_CNT(block_id) (CVMX_ADD_IO_SEG(0x0001180090000688ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_STXX_COM_CTL(block_id) (CVMX_ADD_IO_SEG(0x0001180090000600ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_STXX_DIP_CNT(block_id) (CVMX_ADD_IO_SEG(0x0001180090000690ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_STXX_IGN_CAL(block_id) (CVMX_ADD_IO_SEG(0x0001180090000610ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_STXX_INT_MSK(block_id) (CVMX_ADD_IO_SEG(0x00011800900006A0ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_STXX_INT_REG(block_id) (CVMX_ADD_IO_SEG(0x0001180090000698ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_STXX_INT_SYNC(block_id) (CVMX_ADD_IO_SEG(0x00011800900006A8ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_STXX_MIN_BST(block_id) (CVMX_ADD_IO_SEG(0x0001180090000618ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_STXX_SPI4_CALX(offset, block_id) (CVMX_ADD_IO_SEG(0x0001180090000400ull) + (((offset) & 31) + ((block_id) & 1) * 0x1000000ull) * 8)
+#define CVMX_STXX_SPI4_DAT(block_id) (CVMX_ADD_IO_SEG(0x0001180090000628ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_STXX_SPI4_STAT(block_id) (CVMX_ADD_IO_SEG(0x0001180090000630ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_STXX_STAT_BYTES_HI(block_id) (CVMX_ADD_IO_SEG(0x0001180090000648ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_STXX_STAT_BYTES_LO(block_id) (CVMX_ADD_IO_SEG(0x0001180090000680ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_STXX_STAT_CTL(block_id) (CVMX_ADD_IO_SEG(0x0001180090000638ull) + ((block_id) & 1) * 0x8000000ull)
+#define CVMX_STXX_STAT_PKT_XMT(block_id) (CVMX_ADD_IO_SEG(0x0001180090000640ull) + ((block_id) & 1) * 0x8000000ull)
+
+void __cvmx_interrupt_stxx_int_msk_enable(int index);
+
+union cvmx_stxx_arb_ctl {
+	uint64_t u64;
+	struct cvmx_stxx_arb_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t mintrn:1;
+		uint64_t reserved_4_4:1;
+		uint64_t igntpa:1;
+		uint64_t reserved_0_2:3;
+#else
+		uint64_t reserved_0_2:3;
+		uint64_t igntpa:1;
+		uint64_t reserved_4_4:1;
+		uint64_t mintrn:1;
+		uint64_t reserved_6_63:58;
+#endif
+	} s;
+};
+
+union cvmx_stxx_bckprs_cnt {
+	uint64_t u64;
+	struct cvmx_stxx_bckprs_cnt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t cnt:32;
+#else
+		uint64_t cnt:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_stxx_com_ctl {
+	uint64_t u64;
+	struct cvmx_stxx_com_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_4_63:60;
+		uint64_t st_en:1;
+		uint64_t reserved_1_2:2;
+		uint64_t inf_en:1;
+#else
+		uint64_t inf_en:1;
+		uint64_t reserved_1_2:2;
+		uint64_t st_en:1;
+		uint64_t reserved_4_63:60;
+#endif
+	} s;
+};
+
+union cvmx_stxx_dip_cnt {
+	uint64_t u64;
+	struct cvmx_stxx_dip_cnt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t frmmax:4;
+		uint64_t dipmax:4;
+#else
+		uint64_t dipmax:4;
+		uint64_t frmmax:4;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_stxx_ign_cal {
+	uint64_t u64;
+	struct cvmx_stxx_ign_cal_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t igntpa:16;
+#else
+		uint64_t igntpa:16;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_stxx_int_msk {
+	uint64_t u64;
+	struct cvmx_stxx_int_msk_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t frmerr:1;
+		uint64_t unxfrm:1;
+		uint64_t nosync:1;
+		uint64_t diperr:1;
+		uint64_t datovr:1;
+		uint64_t ovrbst:1;
+		uint64_t calpar1:1;
+		uint64_t calpar0:1;
+#else
+		uint64_t calpar0:1;
+		uint64_t calpar1:1;
+		uint64_t ovrbst:1;
+		uint64_t datovr:1;
+		uint64_t diperr:1;
+		uint64_t nosync:1;
+		uint64_t unxfrm:1;
+		uint64_t frmerr:1;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_stxx_int_reg {
+	uint64_t u64;
+	struct cvmx_stxx_int_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_9_63:55;
+		uint64_t syncerr:1;
+		uint64_t frmerr:1;
+		uint64_t unxfrm:1;
+		uint64_t nosync:1;
+		uint64_t diperr:1;
+		uint64_t datovr:1;
+		uint64_t ovrbst:1;
+		uint64_t calpar1:1;
+		uint64_t calpar0:1;
+#else
+		uint64_t calpar0:1;
+		uint64_t calpar1:1;
+		uint64_t ovrbst:1;
+		uint64_t datovr:1;
+		uint64_t diperr:1;
+		uint64_t nosync:1;
+		uint64_t unxfrm:1;
+		uint64_t frmerr:1;
+		uint64_t syncerr:1;
+		uint64_t reserved_9_63:55;
+#endif
+	} s;
+};
+
+union cvmx_stxx_int_sync {
+	uint64_t u64;
+	struct cvmx_stxx_int_sync_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t frmerr:1;
+		uint64_t unxfrm:1;
+		uint64_t nosync:1;
+		uint64_t diperr:1;
+		uint64_t datovr:1;
+		uint64_t ovrbst:1;
+		uint64_t calpar1:1;
+		uint64_t calpar0:1;
+#else
+		uint64_t calpar0:1;
+		uint64_t calpar1:1;
+		uint64_t ovrbst:1;
+		uint64_t datovr:1;
+		uint64_t diperr:1;
+		uint64_t nosync:1;
+		uint64_t unxfrm:1;
+		uint64_t frmerr:1;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_stxx_min_bst {
+	uint64_t u64;
+	struct cvmx_stxx_min_bst_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_9_63:55;
+		uint64_t minb:9;
+#else
+		uint64_t minb:9;
+		uint64_t reserved_9_63:55;
+#endif
+	} s;
+};
+
+union cvmx_stxx_spi4_calx {
+	uint64_t u64;
+	struct cvmx_stxx_spi4_calx_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_17_63:47;
+		uint64_t oddpar:1;
+		uint64_t prt3:4;
+		uint64_t prt2:4;
+		uint64_t prt1:4;
+		uint64_t prt0:4;
+#else
+		uint64_t prt0:4;
+		uint64_t prt1:4;
+		uint64_t prt2:4;
+		uint64_t prt3:4;
+		uint64_t oddpar:1;
+		uint64_t reserved_17_63:47;
+#endif
+	} s;
+};
+
+union cvmx_stxx_spi4_dat {
+	uint64_t u64;
+	struct cvmx_stxx_spi4_dat_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t alpha:16;
+		uint64_t max_t:16;
+#else
+		uint64_t max_t:16;
+		uint64_t alpha:16;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_stxx_spi4_stat {
+	uint64_t u64;
+	struct cvmx_stxx_spi4_stat_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_16_63:48;
+		uint64_t m:8;
+		uint64_t reserved_7_7:1;
+		uint64_t len:7;
+#else
+		uint64_t len:7;
+		uint64_t reserved_7_7:1;
+		uint64_t m:8;
+		uint64_t reserved_16_63:48;
+#endif
+	} s;
+};
+
+union cvmx_stxx_stat_bytes_hi {
+	uint64_t u64;
+	struct cvmx_stxx_stat_bytes_hi_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t cnt:32;
+#else
+		uint64_t cnt:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_stxx_stat_bytes_lo {
+	uint64_t u64;
+	struct cvmx_stxx_stat_bytes_lo_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t cnt:32;
+#else
+		uint64_t cnt:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_stxx_stat_ctl {
+	uint64_t u64;
+	struct cvmx_stxx_stat_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_5_63:59;
+		uint64_t clr:1;
+		uint64_t bckprs:4;
+#else
+		uint64_t bckprs:4;
+		uint64_t clr:1;
+		uint64_t reserved_5_63:59;
+#endif
+	} s;
+};
+
+union cvmx_stxx_stat_pkt_xmt {
+	uint64_t u64;
+	struct cvmx_stxx_stat_pkt_xmt_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t cnt:32;
+#else
+		uint64_t cnt:32;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-sysinfo.h b/arch/mips/include/asm/octeon/cvmx-sysinfo.h
new file mode 100644
index 000000000..c6c3ee39c
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-sysinfo.h
@@ -0,0 +1,125 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2016 Cavium, Inc.
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ * This module provides system/board information obtained by the bootloader.
+ */
+
+#ifndef __CVMX_SYSINFO_H__
+#define __CVMX_SYSINFO_H__
+
+#include "cvmx-coremask.h"
+
+#define OCTEON_SERIAL_LEN 20
+/**
+ * Structure describing application specific information.
+ * __cvmx_app_init() populates this from the cvmx boot descriptor.
+ * This structure is private to simple executive applications, so
+ * no versioning is required.
+ *
+ * This structure must be provided with some fields set in order to
+ * use simple executive functions in other applications (Linux kernel,
+ * u-boot, etc.)  The cvmx_sysinfo_minimal_initialize() function is
+ * provided to set the required values in these cases.
+ */
+struct cvmx_sysinfo {
+	/* System wide variables */
+	/* installed DRAM in system, in bytes */
+	uint64_t system_dram_size;
+
+	/* ptr to memory descriptor block */
+	uint64_t phy_mem_desc_addr;
+
+	/* Application image specific variables */
+	/* stack top address (virtual) */
+	uint64_t stack_top;
+	/* heap base address (virtual) */
+	uint64_t heap_base;
+	/* stack size in bytes */
+	uint32_t stack_size;
+	/* heap size in bytes */
+	uint32_t heap_size;
+	/* coremask defining cores running application */
+	struct cvmx_coremask core_mask;
+	/* Deprecated, use cvmx_coremask_first_core() to select init core */
+	uint32_t init_core;
+
+	/* exception base address, as set by bootloader */
+	uint64_t exception_base_addr;
+
+	/* cpu clock speed in hz */
+	uint32_t cpu_clock_hz;
+
+	/* dram data rate in hz (data rate = 2 * clock rate */
+	uint32_t dram_data_rate_hz;
+
+
+	uint16_t board_type;
+	uint8_t board_rev_major;
+	uint8_t board_rev_minor;
+	uint8_t mac_addr_base[6];
+	uint8_t mac_addr_count;
+	char board_serial_number[OCTEON_SERIAL_LEN];
+	/*
+	 * Several boards support compact flash on the Octeon boot
+	 * bus.	 The CF memory spaces may be mapped to different
+	 * addresses on different boards.  These values will be 0 if
+	 * CF is not present.  Note that these addresses are physical
+	 * addresses, and it is up to the application to use the
+	 * proper addressing mode (XKPHYS, KSEG0, etc.)
+	 */
+	uint64_t compact_flash_common_base_addr;
+	uint64_t compact_flash_attribute_base_addr;
+	/*
+	 * Base address of the LED display (as on EBT3000 board) This
+	 * will be 0 if LED display not present.  Note that this
+	 * address is a physical address, and it is up to the
+	 * application to use the proper addressing mode (XKPHYS,
+	 * KSEG0, etc.)
+	 */
+	uint64_t led_display_base_addr;
+	/* DFA reference clock in hz (if applicable)*/
+	uint32_t dfa_ref_clock_hz;
+	/* configuration flags from bootloader */
+	uint32_t bootloader_config_flags;
+
+	/* Uart number used for console */
+	uint8_t console_uart_num;
+};
+
+/**
+ * This function returns the system/board information as obtained
+ * by the bootloader.
+ *
+ *
+ * Returns  Pointer to the boot information structure
+ *
+ */
+
+extern struct cvmx_sysinfo *cvmx_sysinfo_get(void);
+
+#endif /* __CVMX_SYSINFO_H__ */
diff --git a/arch/mips/include/asm/octeon/cvmx-uctlx-defs.h b/arch/mips/include/asm/octeon/cvmx-uctlx-defs.h
new file mode 100644
index 000000000..6cf228016
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-uctlx-defs.h
@@ -0,0 +1,386 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2012 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_UCTLX_DEFS_H__
+#define __CVMX_UCTLX_DEFS_H__
+
+#define CVMX_UCTLX_BIST_STATUS(block_id) (CVMX_ADD_IO_SEG(0x000118006F0000A0ull))
+#define CVMX_UCTLX_CLK_RST_CTL(block_id) (CVMX_ADD_IO_SEG(0x000118006F000000ull))
+#define CVMX_UCTLX_EHCI_CTL(block_id) (CVMX_ADD_IO_SEG(0x000118006F000080ull))
+#define CVMX_UCTLX_EHCI_FLA(block_id) (CVMX_ADD_IO_SEG(0x000118006F0000A8ull))
+#define CVMX_UCTLX_ERTO_CTL(block_id) (CVMX_ADD_IO_SEG(0x000118006F000090ull))
+#define CVMX_UCTLX_IF_ENA(block_id) (CVMX_ADD_IO_SEG(0x000118006F000030ull))
+#define CVMX_UCTLX_INT_ENA(block_id) (CVMX_ADD_IO_SEG(0x000118006F000028ull))
+#define CVMX_UCTLX_INT_REG(block_id) (CVMX_ADD_IO_SEG(0x000118006F000020ull))
+#define CVMX_UCTLX_OHCI_CTL(block_id) (CVMX_ADD_IO_SEG(0x000118006F000088ull))
+#define CVMX_UCTLX_ORTO_CTL(block_id) (CVMX_ADD_IO_SEG(0x000118006F000098ull))
+#define CVMX_UCTLX_PPAF_WM(block_id) (CVMX_ADD_IO_SEG(0x000118006F000038ull))
+#define CVMX_UCTLX_UPHY_CTL_STATUS(block_id) (CVMX_ADD_IO_SEG(0x000118006F000008ull))
+#define CVMX_UCTLX_UPHY_PORTX_CTL_STATUS(offset, block_id) (CVMX_ADD_IO_SEG(0x000118006F000010ull) + (((offset) & 1) + ((block_id) & 0) * 0x0ull) * 8)
+
+union cvmx_uctlx_bist_status {
+	uint64_t u64;
+	struct cvmx_uctlx_bist_status_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t data_bis:1;
+		uint64_t desc_bis:1;
+		uint64_t erbm_bis:1;
+		uint64_t orbm_bis:1;
+		uint64_t wrbm_bis:1;
+		uint64_t ppaf_bis:1;
+#else
+		uint64_t ppaf_bis:1;
+		uint64_t wrbm_bis:1;
+		uint64_t orbm_bis:1;
+		uint64_t erbm_bis:1;
+		uint64_t desc_bis:1;
+		uint64_t data_bis:1;
+		uint64_t reserved_6_63:58;
+#endif
+	} s;
+};
+
+union cvmx_uctlx_clk_rst_ctl {
+	uint64_t u64;
+	struct cvmx_uctlx_clk_rst_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_25_63:39;
+		uint64_t clear_bist:1;
+		uint64_t start_bist:1;
+		uint64_t ehci_sm:1;
+		uint64_t ohci_clkcktrst:1;
+		uint64_t ohci_sm:1;
+		uint64_t ohci_susp_lgcy:1;
+		uint64_t app_start_clk:1;
+		uint64_t o_clkdiv_rst:1;
+		uint64_t h_clkdiv_byp:1;
+		uint64_t h_clkdiv_rst:1;
+		uint64_t h_clkdiv_en:1;
+		uint64_t o_clkdiv_en:1;
+		uint64_t h_div:4;
+		uint64_t p_refclk_sel:2;
+		uint64_t p_refclk_div:2;
+		uint64_t reserved_4_4:1;
+		uint64_t p_com_on:1;
+		uint64_t p_por:1;
+		uint64_t p_prst:1;
+		uint64_t hrst:1;
+#else
+		uint64_t hrst:1;
+		uint64_t p_prst:1;
+		uint64_t p_por:1;
+		uint64_t p_com_on:1;
+		uint64_t reserved_4_4:1;
+		uint64_t p_refclk_div:2;
+		uint64_t p_refclk_sel:2;
+		uint64_t h_div:4;
+		uint64_t o_clkdiv_en:1;
+		uint64_t h_clkdiv_en:1;
+		uint64_t h_clkdiv_rst:1;
+		uint64_t h_clkdiv_byp:1;
+		uint64_t o_clkdiv_rst:1;
+		uint64_t app_start_clk:1;
+		uint64_t ohci_susp_lgcy:1;
+		uint64_t ohci_sm:1;
+		uint64_t ohci_clkcktrst:1;
+		uint64_t ehci_sm:1;
+		uint64_t start_bist:1;
+		uint64_t clear_bist:1;
+		uint64_t reserved_25_63:39;
+#endif
+	} s;
+};
+
+union cvmx_uctlx_ehci_ctl {
+	uint64_t u64;
+	struct cvmx_uctlx_ehci_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_20_63:44;
+		uint64_t desc_rbm:1;
+		uint64_t reg_nb:1;
+		uint64_t l2c_dc:1;
+		uint64_t l2c_bc:1;
+		uint64_t l2c_0pag:1;
+		uint64_t l2c_stt:1;
+		uint64_t l2c_buff_emod:2;
+		uint64_t l2c_desc_emod:2;
+		uint64_t inv_reg_a2:1;
+		uint64_t ehci_64b_addr_en:1;
+		uint64_t l2c_addr_msb:8;
+#else
+		uint64_t l2c_addr_msb:8;
+		uint64_t ehci_64b_addr_en:1;
+		uint64_t inv_reg_a2:1;
+		uint64_t l2c_desc_emod:2;
+		uint64_t l2c_buff_emod:2;
+		uint64_t l2c_stt:1;
+		uint64_t l2c_0pag:1;
+		uint64_t l2c_bc:1;
+		uint64_t l2c_dc:1;
+		uint64_t reg_nb:1;
+		uint64_t desc_rbm:1;
+		uint64_t reserved_20_63:44;
+#endif
+	} s;
+};
+
+union cvmx_uctlx_ehci_fla {
+	uint64_t u64;
+	struct cvmx_uctlx_ehci_fla_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_6_63:58;
+		uint64_t fla:6;
+#else
+		uint64_t fla:6;
+		uint64_t reserved_6_63:58;
+#endif
+	} s;
+};
+
+union cvmx_uctlx_erto_ctl {
+	uint64_t u64;
+	struct cvmx_uctlx_erto_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t to_val:27;
+		uint64_t reserved_0_4:5;
+#else
+		uint64_t reserved_0_4:5;
+		uint64_t to_val:27;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_uctlx_if_ena {
+	uint64_t u64;
+	struct cvmx_uctlx_if_ena_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_1_63:63;
+		uint64_t en:1;
+#else
+		uint64_t en:1;
+		uint64_t reserved_1_63:63;
+#endif
+	} s;
+};
+
+union cvmx_uctlx_int_ena {
+	uint64_t u64;
+	struct cvmx_uctlx_int_ena_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t ec_ovf_e:1;
+		uint64_t oc_ovf_e:1;
+		uint64_t wb_pop_e:1;
+		uint64_t wb_psh_f:1;
+		uint64_t cf_psh_f:1;
+		uint64_t or_psh_f:1;
+		uint64_t er_psh_f:1;
+		uint64_t pp_psh_f:1;
+#else
+		uint64_t pp_psh_f:1;
+		uint64_t er_psh_f:1;
+		uint64_t or_psh_f:1;
+		uint64_t cf_psh_f:1;
+		uint64_t wb_psh_f:1;
+		uint64_t wb_pop_e:1;
+		uint64_t oc_ovf_e:1;
+		uint64_t ec_ovf_e:1;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_uctlx_int_reg {
+	uint64_t u64;
+	struct cvmx_uctlx_int_reg_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_8_63:56;
+		uint64_t ec_ovf_e:1;
+		uint64_t oc_ovf_e:1;
+		uint64_t wb_pop_e:1;
+		uint64_t wb_psh_f:1;
+		uint64_t cf_psh_f:1;
+		uint64_t or_psh_f:1;
+		uint64_t er_psh_f:1;
+		uint64_t pp_psh_f:1;
+#else
+		uint64_t pp_psh_f:1;
+		uint64_t er_psh_f:1;
+		uint64_t or_psh_f:1;
+		uint64_t cf_psh_f:1;
+		uint64_t wb_psh_f:1;
+		uint64_t wb_pop_e:1;
+		uint64_t oc_ovf_e:1;
+		uint64_t ec_ovf_e:1;
+		uint64_t reserved_8_63:56;
+#endif
+	} s;
+};
+
+union cvmx_uctlx_ohci_ctl {
+	uint64_t u64;
+	struct cvmx_uctlx_ohci_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_19_63:45;
+		uint64_t reg_nb:1;
+		uint64_t l2c_dc:1;
+		uint64_t l2c_bc:1;
+		uint64_t l2c_0pag:1;
+		uint64_t l2c_stt:1;
+		uint64_t l2c_buff_emod:2;
+		uint64_t l2c_desc_emod:2;
+		uint64_t inv_reg_a2:1;
+		uint64_t reserved_8_8:1;
+		uint64_t l2c_addr_msb:8;
+#else
+		uint64_t l2c_addr_msb:8;
+		uint64_t reserved_8_8:1;
+		uint64_t inv_reg_a2:1;
+		uint64_t l2c_desc_emod:2;
+		uint64_t l2c_buff_emod:2;
+		uint64_t l2c_stt:1;
+		uint64_t l2c_0pag:1;
+		uint64_t l2c_bc:1;
+		uint64_t l2c_dc:1;
+		uint64_t reg_nb:1;
+		uint64_t reserved_19_63:45;
+#endif
+	} s;
+};
+
+union cvmx_uctlx_orto_ctl {
+	uint64_t u64;
+	struct cvmx_uctlx_orto_ctl_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_32_63:32;
+		uint64_t to_val:24;
+		uint64_t reserved_0_7:8;
+#else
+		uint64_t reserved_0_7:8;
+		uint64_t to_val:24;
+		uint64_t reserved_32_63:32;
+#endif
+	} s;
+};
+
+union cvmx_uctlx_ppaf_wm {
+	uint64_t u64;
+	struct cvmx_uctlx_ppaf_wm_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_5_63:59;
+		uint64_t wm:5;
+#else
+		uint64_t wm:5;
+		uint64_t reserved_5_63:59;
+#endif
+	} s;
+};
+
+union cvmx_uctlx_uphy_ctl_status {
+	uint64_t u64;
+	struct cvmx_uctlx_uphy_ctl_status_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_10_63:54;
+		uint64_t bist_done:1;
+		uint64_t bist_err:1;
+		uint64_t hsbist:1;
+		uint64_t fsbist:1;
+		uint64_t lsbist:1;
+		uint64_t siddq:1;
+		uint64_t vtest_en:1;
+		uint64_t uphy_bist:1;
+		uint64_t bist_en:1;
+		uint64_t ate_reset:1;
+#else
+		uint64_t ate_reset:1;
+		uint64_t bist_en:1;
+		uint64_t uphy_bist:1;
+		uint64_t vtest_en:1;
+		uint64_t siddq:1;
+		uint64_t lsbist:1;
+		uint64_t fsbist:1;
+		uint64_t hsbist:1;
+		uint64_t bist_err:1;
+		uint64_t bist_done:1;
+		uint64_t reserved_10_63:54;
+#endif
+	} s;
+};
+
+union cvmx_uctlx_uphy_portx_ctl_status {
+	uint64_t u64;
+	struct cvmx_uctlx_uphy_portx_ctl_status_s {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t reserved_43_63:21;
+		uint64_t tdata_out:4;
+		uint64_t txbiststuffenh:1;
+		uint64_t txbiststuffen:1;
+		uint64_t dmpulldown:1;
+		uint64_t dppulldown:1;
+		uint64_t vbusvldext:1;
+		uint64_t portreset:1;
+		uint64_t txhsvxtune:2;
+		uint64_t txvreftune:4;
+		uint64_t txrisetune:1;
+		uint64_t txpreemphasistune:1;
+		uint64_t txfslstune:4;
+		uint64_t sqrxtune:3;
+		uint64_t compdistune:3;
+		uint64_t loop_en:1;
+		uint64_t tclk:1;
+		uint64_t tdata_sel:1;
+		uint64_t taddr_in:4;
+		uint64_t tdata_in:8;
+#else
+		uint64_t tdata_in:8;
+		uint64_t taddr_in:4;
+		uint64_t tdata_sel:1;
+		uint64_t tclk:1;
+		uint64_t loop_en:1;
+		uint64_t compdistune:3;
+		uint64_t sqrxtune:3;
+		uint64_t txfslstune:4;
+		uint64_t txpreemphasistune:1;
+		uint64_t txrisetune:1;
+		uint64_t txvreftune:4;
+		uint64_t txhsvxtune:2;
+		uint64_t portreset:1;
+		uint64_t vbusvldext:1;
+		uint64_t dppulldown:1;
+		uint64_t dmpulldown:1;
+		uint64_t txbiststuffen:1;
+		uint64_t txbiststuffenh:1;
+		uint64_t tdata_out:4;
+		uint64_t reserved_43_63:21;
+#endif
+	} s;
+};
+
+#endif
diff --git a/arch/mips/include/asm/octeon/cvmx-wqe.h b/arch/mips/include/asm/octeon/cvmx-wqe.h
new file mode 100644
index 000000000..9cec2299b
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx-wqe.h
@@ -0,0 +1,658 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/**
+ *
+ * This header file defines the work queue entry (wqe) data structure.
+ * Since this is a commonly used structure that depends on structures
+ * from several hardware blocks, those definitions have been placed
+ * in this file to create a single point of definition of the wqe
+ * format.
+ * Data structures are still named according to the block that they
+ * relate to.
+ *
+ */
+
+#ifndef __CVMX_WQE_H__
+#define __CVMX_WQE_H__
+
+#include <asm/octeon/cvmx-packet.h>
+
+
+#define OCT_TAG_TYPE_STRING(x)						\
+	(((x) == CVMX_POW_TAG_TYPE_ORDERED) ?  "ORDERED" :		\
+		(((x) == CVMX_POW_TAG_TYPE_ATOMIC) ?  "ATOMIC" :	\
+			(((x) == CVMX_POW_TAG_TYPE_NULL) ?  "NULL" :	\
+				"NULL_NULL")))
+
+/**
+ * HW decode / err_code in work queue entry
+ */
+typedef union {
+	uint64_t u64;
+
+	/* Use this struct if the hardware determines that the packet is IP */
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		/* HW sets this to the number of buffers used by this packet */
+		uint64_t bufs:8;
+		/* HW sets to the number of L2 bytes prior to the IP */
+		uint64_t ip_offset:8;
+		/* set to 1 if we found DSA/VLAN in the L2 */
+		uint64_t vlan_valid:1;
+		/* Set to 1 if the DSA/VLAN tag is stacked */
+		uint64_t vlan_stacked:1;
+		uint64_t unassigned:1;
+		/* HW sets to the DSA/VLAN CFI flag (valid when vlan_valid) */
+		uint64_t vlan_cfi:1;
+		/* HW sets to the DSA/VLAN_ID field (valid when vlan_valid) */
+		uint64_t vlan_id:12;
+		/* Ring Identifier (if PCIe). Requires PIP_GBL_CTL[RING_EN]=1 */
+		uint64_t pr:4;
+		uint64_t unassigned2:8;
+		/* the packet needs to be decompressed */
+		uint64_t dec_ipcomp:1;
+		/* the packet is either TCP or UDP */
+		uint64_t tcp_or_udp:1;
+		/* the packet needs to be decrypted (ESP or AH) */
+		uint64_t dec_ipsec:1;
+		/* the packet is IPv6 */
+		uint64_t is_v6:1;
+
+		/*
+		 * (rcv_error, not_IP, IP_exc, is_frag, L4_error,
+		 * software, etc.).
+		 */
+
+		/*
+		 * reserved for software use, hardware will clear on
+		 * packet creation.
+		 */
+		uint64_t software:1;
+		/* exceptional conditions below */
+		/* the receive interface hardware detected an L4 error
+		 * (only applies if !is_frag) (only applies if
+		 * !rcv_error && !not_IP && !IP_exc && !is_frag)
+		 * failure indicated in err_code below, decode:
+		 *
+		 * - 1 = Malformed L4
+		 * - 2 = L4 Checksum Error: the L4 checksum value is
+		 * - 3 = UDP Length Error: The UDP length field would
+		 *	 make the UDP data longer than what remains in
+		 *	 the IP packet (as defined by the IP header
+		 *	 length field).
+		 * - 4 = Bad L4 Port: either the source or destination
+		 *	 TCP/UDP port is 0.
+		 * - 8 = TCP FIN Only: the packet is TCP and only the
+		 *	 FIN flag set.
+		 * - 9 = TCP No Flags: the packet is TCP and no flags
+		 *	 are set.
+		 * - 10 = TCP FIN RST: the packet is TCP and both FIN
+		 *	  and RST are set.
+		 * - 11 = TCP SYN URG: the packet is TCP and both SYN
+		 *	  and URG are set.
+		 * - 12 = TCP SYN RST: the packet is TCP and both SYN
+		 *	  and RST are set.
+		 * - 13 = TCP SYN FIN: the packet is TCP and both SYN
+		 *	  and FIN are set.
+		 */
+		uint64_t L4_error:1;
+		/* set if the packet is a fragment */
+		uint64_t is_frag:1;
+		/* the receive interface hardware detected an IP error
+		 * / exception (only applies if !rcv_error && !not_IP)
+		 * failure indicated in err_code below, decode:
+		 *
+		 * - 1 = Not IP: the IP version field is neither 4 nor
+		 *	 6.
+		 * - 2 = IPv4 Header Checksum Error: the IPv4 header
+		 *	 has a checksum violation.
+		 * - 3 = IP Malformed Header: the packet is not long
+		 *	 enough to contain the IP header.
+		 * - 4 = IP Malformed: the packet is not long enough
+		 *	 to contain the bytes indicated by the IP
+		 *	 header. Pad is allowed.
+		 * - 5 = IP TTL Hop: the IPv4 TTL field or the IPv6
+		 *	 Hop Count field are zero.
+		 * - 6 = IP Options
+		 */
+		uint64_t IP_exc:1;
+		/*
+		 * Set if the hardware determined that the packet is a
+		 * broadcast.
+		 */
+		uint64_t is_bcast:1;
+		/*
+		 * St if the hardware determined that the packet is a
+		 * multi-cast.
+		 */
+		uint64_t is_mcast:1;
+		/*
+		 * Set if the packet may not be IP (must be zero in
+		 * this case).
+		 */
+		uint64_t not_IP:1;
+		/*
+		 * The receive interface hardware detected a receive
+		 * error (must be zero in this case).
+		 */
+		uint64_t rcv_error:1;
+		/* lower err_code = first-level descriptor of the
+		 * work */
+		/* zero for packet submitted by hardware that isn't on
+		 * the slow path */
+		/* type is cvmx_pip_err_t */
+		uint64_t err_code:8;
+#else
+	        uint64_t err_code:8;
+	        uint64_t rcv_error:1;
+	        uint64_t not_IP:1;
+	        uint64_t is_mcast:1;
+	        uint64_t is_bcast:1;
+	        uint64_t IP_exc:1;
+	        uint64_t is_frag:1;
+	        uint64_t L4_error:1;
+	        uint64_t software:1;
+	        uint64_t is_v6:1;
+	        uint64_t dec_ipsec:1;
+	        uint64_t tcp_or_udp:1;
+	        uint64_t dec_ipcomp:1;
+	        uint64_t unassigned2:4;
+	        uint64_t unassigned2a:4;
+	        uint64_t pr:4;
+	        uint64_t vlan_id:12;
+	        uint64_t vlan_cfi:1;
+	        uint64_t unassigned:1;
+	        uint64_t vlan_stacked:1;
+	        uint64_t vlan_valid:1;
+	        uint64_t ip_offset:8;
+	        uint64_t bufs:8;
+#endif
+	} s;
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t bufs:8;
+		uint64_t ip_offset:8;
+		uint64_t vlan_valid:1;
+		uint64_t vlan_stacked:1;
+		uint64_t unassigned:1;
+		uint64_t vlan_cfi:1;
+		uint64_t vlan_id:12;
+		uint64_t port:12;		/* MAC/PIP port number. */
+		uint64_t dec_ipcomp:1;
+		uint64_t tcp_or_udp:1;
+		uint64_t dec_ipsec:1;
+		uint64_t is_v6:1;
+		uint64_t software:1;
+		uint64_t L4_error:1;
+		uint64_t is_frag:1;
+		uint64_t IP_exc:1;
+		uint64_t is_bcast:1;
+		uint64_t is_mcast:1;
+		uint64_t not_IP:1;
+		uint64_t rcv_error:1;
+		uint64_t err_code:8;
+#else
+		uint64_t err_code:8;
+		uint64_t rcv_error:1;
+		uint64_t not_IP:1;
+		uint64_t is_mcast:1;
+		uint64_t is_bcast:1;
+		uint64_t IP_exc:1;
+		uint64_t is_frag:1;
+		uint64_t L4_error:1;
+		uint64_t software:1;
+		uint64_t is_v6:1;
+		uint64_t dec_ipsec:1;
+		uint64_t tcp_or_udp:1;
+		uint64_t dec_ipcomp:1;
+		uint64_t port:12;
+		uint64_t vlan_id:12;
+		uint64_t vlan_cfi:1;
+		uint64_t unassigned:1;
+		uint64_t vlan_stacked:1;
+		uint64_t vlan_valid:1;
+		uint64_t ip_offset:8;
+		uint64_t bufs:8;
+#endif
+	} s_cn68xx;
+
+	/* use this to get at the 16 vlan bits */
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t unused1:16;
+		uint64_t vlan:16;
+		uint64_t unused2:32;
+#else
+	        uint64_t unused2:32;
+	        uint64_t vlan:16;
+	        uint64_t unused1:16;
+
+#endif
+	} svlan;
+
+	/*
+	 * use this struct if the hardware could not determine that
+	 * the packet is ip.
+	 */
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		/*
+		 * HW sets this to the number of buffers used by this
+		 * packet.
+		 */
+		uint64_t bufs:8;
+		uint64_t unused:8;
+		/* set to 1 if we found DSA/VLAN in the L2 */
+		uint64_t vlan_valid:1;
+		/* Set to 1 if the DSA/VLAN tag is stacked */
+		uint64_t vlan_stacked:1;
+		uint64_t unassigned:1;
+		/*
+		 * HW sets to the DSA/VLAN CFI flag (valid when
+		 * vlan_valid)
+		 */
+		uint64_t vlan_cfi:1;
+		/*
+		 * HW sets to the DSA/VLAN_ID field (valid when
+		 * vlan_valid).
+		 */
+		uint64_t vlan_id:12;
+		/*
+		 * Ring Identifier (if PCIe). Requires
+		 * PIP_GBL_CTL[RING_EN]=1
+		 */
+		uint64_t pr:4;
+		uint64_t unassigned2:12;
+		/*
+		 * reserved for software use, hardware will clear on
+		 * packet creation.
+		 */
+		uint64_t software:1;
+		uint64_t unassigned3:1;
+		/*
+		 * set if the hardware determined that the packet is
+		 * rarp.
+		 */
+		uint64_t is_rarp:1;
+		/*
+		 * set if the hardware determined that the packet is
+		 * arp
+		 */
+		uint64_t is_arp:1;
+		/*
+		 * set if the hardware determined that the packet is a
+		 * broadcast.
+		 */
+		uint64_t is_bcast:1;
+		/*
+		 * set if the hardware determined that the packet is a
+		 * multi-cast
+		 */
+		uint64_t is_mcast:1;
+		/*
+		 * set if the packet may not be IP (must be one in
+		 * this case)
+		 */
+		uint64_t not_IP:1;
+		/* The receive interface hardware detected a receive
+		 * error.  Failure indicated in err_code below,
+		 * decode:
+		 *
+		 * - 1 = partial error: a packet was partially
+		 *	 received, but internal buffering / bandwidth
+		 *	 was not adequate to receive the entire
+		 *	 packet.
+		 * - 2 = jabber error: the RGMII packet was too large
+		 *	 and is truncated.
+		 * - 3 = overrun error: the RGMII packet is longer
+		 *	 than allowed and had an FCS error.
+		 * - 4 = oversize error: the RGMII packet is longer
+		 *	 than allowed.
+		 * - 5 = alignment error: the RGMII packet is not an
+		 *	 integer number of bytes
+		 *	 and had an FCS error (100M and 10M only).
+		 * - 6 = fragment error: the RGMII packet is shorter
+		 *	 than allowed and had an FCS error.
+		 * - 7 = GMX FCS error: the RGMII packet had an FCS
+		 *	 error.
+		 * - 8 = undersize error: the RGMII packet is shorter
+		 *	 than allowed.
+		 * - 9 = extend error: the RGMII packet had an extend
+		 *	 error.
+		 * - 10 = length mismatch error: the RGMII packet had
+		 *	  a length that did not match the length field
+		 *	  in the L2 HDR.
+		 * - 11 = RGMII RX error/SPI4 DIP4 Error: the RGMII
+		 *	  packet had one or more data reception errors
+		 *	  (RXERR) or the SPI4 packet had one or more
+		 *	  DIP4 errors.
+		 * - 12 = RGMII skip error/SPI4 Abort Error: the RGMII
+		 *	  packet was not large enough to cover the
+		 *	  skipped bytes or the SPI4 packet was
+		 *	  terminated with an About EOPS.
+		 * - 13 = RGMII nibble error/SPI4 Port NXA Error: the
+		 *	  RGMII packet had a studder error (data not
+		 *	  repeated - 10/100M only) or the SPI4 packet
+		 *	  was sent to an NXA.
+		 * - 16 = FCS error: a SPI4.2 packet had an FCS error.
+		 * - 17 = Skip error: a packet was not large enough to
+		 *	  cover the skipped bytes.
+		 * - 18 = L2 header malformed: the packet is not long
+		 *	  enough to contain the L2.
+		 */
+
+		uint64_t rcv_error:1;
+		/*
+		 * lower err_code = first-level descriptor of the
+		 * work
+		 */
+		/*
+		 * zero for packet submitted by hardware that isn't on
+		 * the slow path
+		 */
+		/* type is cvmx_pip_err_t (union, so can't use directly */
+		uint64_t err_code:8;
+#else
+	        uint64_t err_code:8;
+	        uint64_t rcv_error:1;
+	        uint64_t not_IP:1;
+	        uint64_t is_mcast:1;
+	        uint64_t is_bcast:1;
+	        uint64_t is_arp:1;
+	        uint64_t is_rarp:1;
+	        uint64_t unassigned3:1;
+	        uint64_t software:1;
+	        uint64_t unassigned2:4;
+	        uint64_t unassigned2a:8;
+	        uint64_t pr:4;
+	        uint64_t vlan_id:12;
+	        uint64_t vlan_cfi:1;
+	        uint64_t unassigned:1;
+	        uint64_t vlan_stacked:1;
+	        uint64_t vlan_valid:1;
+	        uint64_t unused:8;
+	        uint64_t bufs:8;
+#endif
+	} snoip;
+
+} cvmx_pip_wqe_word2;
+
+union cvmx_pip_wqe_word0 {
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		/**
+		 * raw chksum result generated by the HW
+		 */
+		uint16_t hw_chksum;
+		/**
+		 * Field unused by hardware - available for software
+		 */
+		uint8_t unused;
+		/**
+		 * Next pointer used by hardware for list maintenance.
+		 * May be written/read by HW before the work queue
+		 * entry is scheduled to a PP (Only 36 bits used in
+		 * Octeon 1)
+		 */
+		uint64_t next_ptr:40;
+#else
+		uint64_t next_ptr:40;
+		uint8_t unused;
+		uint16_t hw_chksum;
+#endif
+	} cn38xx;
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t l4ptr:8;       /* 56..63 */
+		uint64_t unused0:8;     /* 48..55 */
+		uint64_t l3ptr:8;       /* 40..47 */
+		uint64_t l2ptr:8;       /* 32..39 */
+		uint64_t unused1:18;    /* 14..31 */
+		uint64_t bpid:6;        /* 8..13 */
+		uint64_t unused2:2;     /* 6..7 */
+		uint64_t pknd:6;        /* 0..5 */
+#else
+		uint64_t pknd:6;        /* 0..5 */
+		uint64_t unused2:2;     /* 6..7 */
+		uint64_t bpid:6;        /* 8..13 */
+		uint64_t unused1:18;    /* 14..31 */
+		uint64_t l2ptr:8;       /* 32..39 */
+		uint64_t l3ptr:8;       /* 40..47 */
+		uint64_t unused0:8;     /* 48..55 */
+		uint64_t l4ptr:8;       /* 56..63 */
+#endif
+	} cn68xx;
+};
+
+union cvmx_wqe_word0 {
+	uint64_t u64;
+	union cvmx_pip_wqe_word0 pip;
+};
+
+union cvmx_wqe_word1 {
+	uint64_t u64;
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t len:16;
+		uint64_t varies:14;
+		/**
+		 * the type of the tag (ORDERED, ATOMIC, NULL)
+		 */
+		uint64_t tag_type:2;
+		uint64_t tag:32;
+#else
+		uint64_t tag:32;
+		uint64_t tag_type:2;
+		uint64_t varies:14;
+		uint64_t len:16;
+#endif
+	};
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		uint64_t len:16;
+		uint64_t zero_0:1;
+		/**
+		 * HW sets this to what it thought the priority of
+		 * the input packet was
+		 */
+		uint64_t qos:3;
+
+		uint64_t zero_1:1;
+		/**
+		 * the group that the work queue entry will be scheduled to
+		 */
+		uint64_t grp:6;
+		uint64_t zero_2:3;
+		uint64_t tag_type:2;
+		uint64_t tag:32;
+#else
+		uint64_t tag:32;
+		uint64_t tag_type:2;
+		uint64_t zero_2:3;
+		uint64_t grp:6;
+		uint64_t zero_1:1;
+		uint64_t qos:3;
+		uint64_t zero_0:1;
+		uint64_t len:16;
+#endif
+	} cn68xx;
+	struct {
+#ifdef __BIG_ENDIAN_BITFIELD
+		/**
+		 * HW sets to the total number of bytes in the packet
+		 */
+		uint64_t len:16;
+		/**
+		 * HW sets this to input physical port
+		 */
+		uint64_t ipprt:6;
+
+		/**
+		 * HW sets this to what it thought the priority of
+		 * the input packet was
+		 */
+		uint64_t qos:3;
+
+		/**
+		 * the group that the work queue entry will be scheduled to
+		 */
+		uint64_t grp:4;
+		/**
+		 * the type of the tag (ORDERED, ATOMIC, NULL)
+		 */
+		uint64_t tag_type:3;
+		/**
+		 * the synchronization/ordering tag
+		 */
+		uint64_t tag:32;
+#else
+		uint64_t tag:32;
+		uint64_t tag_type:2;
+		uint64_t zero_2:1;
+		uint64_t grp:4;
+		uint64_t qos:3;
+		uint64_t ipprt:6;
+		uint64_t len:16;
+#endif
+	} cn38xx;
+};
+
+/**
+ * Work queue entry format
+ *
+ * must be 8-byte aligned
+ */
+struct cvmx_wqe {
+
+    /*****************************************************************
+     * WORD 0
+     *	HW WRITE: the following 64 bits are filled by HW when a packet arrives
+     */
+	union cvmx_wqe_word0 word0;
+
+    /*****************************************************************
+     * WORD 1
+     *	HW WRITE: the following 64 bits are filled by HW when a packet arrives
+     */
+	union cvmx_wqe_word1 word1;
+
+    /**
+     * WORD 2 HW WRITE: the following 64-bits are filled in by
+     *	 hardware when a packet arrives This indicates a variety of
+     *	 status and error conditions.
+     */
+	cvmx_pip_wqe_word2 word2;
+
+    /**
+     * Pointer to the first segment of the packet.
+     */
+	union cvmx_buf_ptr packet_ptr;
+
+    /**
+     *	 HW WRITE: octeon will fill in a programmable amount from the
+     *		   packet, up to (at most, but perhaps less) the amount
+     *		   needed to fill the work queue entry to 128 bytes
+     *
+     *	 If the packet is recognized to be IP, the hardware starts
+     *	 (except that the IPv4 header is padded for appropriate
+     *	 alignment) writing here where the IP header starts.  If the
+     *	 packet is not recognized to be IP, the hardware starts
+     *	 writing the beginning of the packet here.
+     */
+	uint8_t packet_data[96];
+
+    /**
+     * If desired, SW can make the work Q entry any length. For the
+     * purposes of discussion here, Assume 128B always, as this is all that
+     * the hardware deals with.
+     *
+     */
+
+} CVMX_CACHE_LINE_ALIGNED;
+
+static inline int cvmx_wqe_get_port(struct cvmx_wqe *work)
+{
+	int port;
+
+	if (octeon_has_feature(OCTEON_FEATURE_CN68XX_WQE))
+		port = work->word2.s_cn68xx.port;
+	else
+		port = work->word1.cn38xx.ipprt;
+
+	return port;
+}
+
+static inline void cvmx_wqe_set_port(struct cvmx_wqe *work, int port)
+{
+	if (octeon_has_feature(OCTEON_FEATURE_CN68XX_WQE))
+		work->word2.s_cn68xx.port = port;
+	else
+		work->word1.cn38xx.ipprt = port;
+}
+
+static inline int cvmx_wqe_get_grp(struct cvmx_wqe *work)
+{
+	int grp;
+
+	if (octeon_has_feature(OCTEON_FEATURE_CN68XX_WQE))
+		grp = work->word1.cn68xx.grp;
+	else
+		grp = work->word1.cn38xx.grp;
+
+	return grp;
+}
+
+static inline void cvmx_wqe_set_grp(struct cvmx_wqe *work, int grp)
+{
+	if (octeon_has_feature(OCTEON_FEATURE_CN68XX_WQE))
+		work->word1.cn68xx.grp = grp;
+	else
+		work->word1.cn38xx.grp = grp;
+}
+
+static inline int cvmx_wqe_get_qos(struct cvmx_wqe *work)
+{
+	int qos;
+
+	if (octeon_has_feature(OCTEON_FEATURE_CN68XX_WQE))
+		qos = work->word1.cn68xx.qos;
+	else
+		qos = work->word1.cn38xx.qos;
+
+	return qos;
+}
+
+static inline void cvmx_wqe_set_qos(struct cvmx_wqe *work, int qos)
+{
+	if (octeon_has_feature(OCTEON_FEATURE_CN68XX_WQE))
+		work->word1.cn68xx.qos = qos;
+	else
+		work->word1.cn38xx.qos = qos;
+}
+
+#endif /* __CVMX_WQE_H__ */
diff --git a/arch/mips/include/asm/octeon/cvmx.h b/arch/mips/include/asm/octeon/cvmx.h
new file mode 100644
index 000000000..25854abc9
--- /dev/null
+++ b/arch/mips/include/asm/octeon/cvmx.h
@@ -0,0 +1,495 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2017 Cavium, Inc.
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+#ifndef __CVMX_H__
+#define __CVMX_H__
+
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <linux/delay.h>
+
+enum cvmx_mips_space {
+	CVMX_MIPS_SPACE_XKSEG = 3LL,
+	CVMX_MIPS_SPACE_XKPHYS = 2LL,
+	CVMX_MIPS_SPACE_XSSEG = 1LL,
+	CVMX_MIPS_SPACE_XUSEG = 0LL
+};
+
+/* These macros for use when using 32 bit pointers. */
+#define CVMX_MIPS32_SPACE_KSEG0 1l
+#define CVMX_ADD_SEG32(segment, add) \
+	(((int32_t)segment << 31) | (int32_t)(add))
+
+#define CVMX_IO_SEG CVMX_MIPS_SPACE_XKPHYS
+
+/* These macros simplify the process of creating common IO addresses */
+#define CVMX_ADD_SEG(segment, add) \
+	((((uint64_t)segment) << 62) | (add))
+#ifndef CVMX_ADD_IO_SEG
+#define CVMX_ADD_IO_SEG(add) CVMX_ADD_SEG(CVMX_IO_SEG, (add))
+#endif
+
+#include <asm/octeon/cvmx-asm.h>
+#include <asm/octeon/cvmx-packet.h>
+#include <asm/octeon/cvmx-sysinfo.h>
+
+#include <asm/octeon/cvmx-ciu-defs.h>
+#include <asm/octeon/cvmx-ciu3-defs.h>
+#include <asm/octeon/cvmx-gpio-defs.h>
+#include <asm/octeon/cvmx-iob-defs.h>
+#include <asm/octeon/cvmx-ipd-defs.h>
+#include <asm/octeon/cvmx-l2c-defs.h>
+#include <asm/octeon/cvmx-l2d-defs.h>
+#include <asm/octeon/cvmx-l2t-defs.h>
+#include <asm/octeon/cvmx-led-defs.h>
+#include <asm/octeon/cvmx-mio-defs.h>
+#include <asm/octeon/cvmx-pow-defs.h>
+
+#include <asm/octeon/cvmx-bootinfo.h>
+#include <asm/octeon/cvmx-bootmem.h>
+#include <asm/octeon/cvmx-l2c.h>
+
+#ifndef CVMX_ENABLE_DEBUG_PRINTS
+#define CVMX_ENABLE_DEBUG_PRINTS 1
+#endif
+
+#if CVMX_ENABLE_DEBUG_PRINTS
+#define cvmx_dprintf	    printk
+#else
+#define cvmx_dprintf(...)   {}
+#endif
+
+#define CVMX_MAX_CORES		(16)
+#define CVMX_CACHE_LINE_SIZE	(128)	/* In bytes */
+#define CVMX_CACHE_LINE_MASK	(CVMX_CACHE_LINE_SIZE - 1)	/* In bytes */
+#define CVMX_CACHE_LINE_ALIGNED __attribute__ ((aligned(CVMX_CACHE_LINE_SIZE)))
+#define CAST64(v) ((long long)(long)(v))
+#define CASTPTR(type, v) ((type *)(long)(v))
+
+/*
+ * Returns processor ID, different Linux and simple exec versions
+ * provided in the cvmx-app-init*.c files.
+ */
+static inline uint32_t cvmx_get_proc_id(void) __attribute__ ((pure));
+static inline uint32_t cvmx_get_proc_id(void)
+{
+	uint32_t id;
+	asm("mfc0 %0, $15,0" : "=r"(id));
+	return id;
+}
+
+/* turn the variable name into a string */
+#define CVMX_TMP_STR(x) CVMX_TMP_STR2(x)
+#define CVMX_TMP_STR2(x) #x
+
+/**
+ * Builds a bit mask given the required size in bits.
+ *
+ * @bits:   Number of bits in the mask
+ * Returns The mask
+ */ static inline uint64_t cvmx_build_mask(uint64_t bits)
+{
+	return ~((~0x0ull) << bits);
+}
+
+/**
+ * Builds a memory address for I/O based on the Major and Sub DID.
+ *
+ * @major_did: 5 bit major did
+ * @sub_did:   3 bit sub did
+ * Returns I/O base address
+ */
+static inline uint64_t cvmx_build_io_address(uint64_t major_did,
+					     uint64_t sub_did)
+{
+	return (0x1ull << 48) | (major_did << 43) | (sub_did << 40);
+}
+
+/**
+ * Perform mask and shift to place the supplied value into
+ * the supplied bit rage.
+ *
+ * Example: cvmx_build_bits(39,24,value)
+ * <pre>
+ * 6	   5	   4	   3	   3	   2	   1
+ * 3	   5	   7	   9	   1	   3	   5	   7	  0
+ * +-------+-------+-------+-------+-------+-------+-------+------+
+ * 000000000000000000000000___________value000000000000000000000000
+ * </pre>
+ *
+ * @high_bit: Highest bit value can occupy (inclusive) 0-63
+ * @low_bit:  Lowest bit value can occupy inclusive 0-high_bit
+ * @value:    Value to use
+ * Returns Value masked and shifted
+ */
+static inline uint64_t cvmx_build_bits(uint64_t high_bit,
+				       uint64_t low_bit, uint64_t value)
+{
+	return (value & cvmx_build_mask(high_bit - low_bit + 1)) << low_bit;
+}
+
+/**
+ * Convert a memory pointer (void*) into a hardware compatible
+ * memory address (uint64_t). Octeon hardware widgets don't
+ * understand logical addresses.
+ *
+ * @ptr:    C style memory pointer
+ * Returns Hardware physical address
+ */
+static inline uint64_t cvmx_ptr_to_phys(void *ptr)
+{
+	if (sizeof(void *) == 8) {
+		/*
+		 * We're running in 64 bit mode. Normally this means
+		 * that we can use 40 bits of address space (the
+		 * hardware limit). Unfortunately there is one case
+		 * were we need to limit this to 30 bits, sign
+		 * extended 32 bit. Although these are 64 bits wide,
+		 * only 30 bits can be used.
+		 */
+		if ((CAST64(ptr) >> 62) == 3)
+			return CAST64(ptr) & cvmx_build_mask(30);
+		else
+			return CAST64(ptr) & cvmx_build_mask(40);
+	} else {
+		return (long)(ptr) & 0x1fffffff;
+	}
+}
+
+/**
+ * Convert a hardware physical address (uint64_t) into a
+ * memory pointer (void *).
+ *
+ * @physical_address:
+ *		 Hardware physical address to memory
+ * Returns Pointer to memory
+ */
+static inline void *cvmx_phys_to_ptr(uint64_t physical_address)
+{
+	if (sizeof(void *) == 8) {
+		/* Just set the top bit, avoiding any TLB ugliness */
+		return CASTPTR(void,
+			       CVMX_ADD_SEG(CVMX_MIPS_SPACE_XKPHYS,
+					    physical_address));
+	} else {
+		return CASTPTR(void,
+			       CVMX_ADD_SEG32(CVMX_MIPS32_SPACE_KSEG0,
+					      physical_address));
+	}
+}
+
+/* The following #if controls the definition of the macro
+    CVMX_BUILD_WRITE64. This macro is used to build a store operation to
+    a full 64bit address. With a 64bit ABI, this can be done with a simple
+    pointer access. 32bit ABIs require more complicated assembly */
+
+/* We have a full 64bit ABI. Writing to a 64bit address can be done with
+    a simple volatile pointer */
+#define CVMX_BUILD_WRITE64(TYPE, ST)					\
+static inline void cvmx_write64_##TYPE(uint64_t addr, TYPE##_t val)	\
+{									\
+    *CASTPTR(volatile TYPE##_t, addr) = val;				\
+}
+
+
+/* The following #if controls the definition of the macro
+    CVMX_BUILD_READ64. This macro is used to build a load operation from
+    a full 64bit address. With a 64bit ABI, this can be done with a simple
+    pointer access. 32bit ABIs require more complicated assembly */
+
+/* We have a full 64bit ABI. Writing to a 64bit address can be done with
+    a simple volatile pointer */
+#define CVMX_BUILD_READ64(TYPE, LT)					\
+static inline TYPE##_t cvmx_read64_##TYPE(uint64_t addr)		\
+{									\
+	return *CASTPTR(volatile TYPE##_t, addr);			\
+}
+
+
+/* The following defines 8 functions for writing to a 64bit address. Each
+    takes two arguments, the address and the value to write.
+    cvmx_write64_int64	    cvmx_write64_uint64
+    cvmx_write64_int32	    cvmx_write64_uint32
+    cvmx_write64_int16	    cvmx_write64_uint16
+    cvmx_write64_int8	    cvmx_write64_uint8 */
+CVMX_BUILD_WRITE64(int64, "sd");
+CVMX_BUILD_WRITE64(int32, "sw");
+CVMX_BUILD_WRITE64(int16, "sh");
+CVMX_BUILD_WRITE64(int8, "sb");
+CVMX_BUILD_WRITE64(uint64, "sd");
+CVMX_BUILD_WRITE64(uint32, "sw");
+CVMX_BUILD_WRITE64(uint16, "sh");
+CVMX_BUILD_WRITE64(uint8, "sb");
+#define cvmx_write64 cvmx_write64_uint64
+
+/* The following defines 8 functions for reading from a 64bit address. Each
+    takes the address as the only argument
+    cvmx_read64_int64	    cvmx_read64_uint64
+    cvmx_read64_int32	    cvmx_read64_uint32
+    cvmx_read64_int16	    cvmx_read64_uint16
+    cvmx_read64_int8	    cvmx_read64_uint8 */
+CVMX_BUILD_READ64(int64, "ld");
+CVMX_BUILD_READ64(int32, "lw");
+CVMX_BUILD_READ64(int16, "lh");
+CVMX_BUILD_READ64(int8, "lb");
+CVMX_BUILD_READ64(uint64, "ld");
+CVMX_BUILD_READ64(uint32, "lw");
+CVMX_BUILD_READ64(uint16, "lhu");
+CVMX_BUILD_READ64(uint8, "lbu");
+#define cvmx_read64 cvmx_read64_uint64
+
+
+static inline void cvmx_write_csr(uint64_t csr_addr, uint64_t val)
+{
+	cvmx_write64(csr_addr, val);
+
+	/*
+	 * Perform an immediate read after every write to an RSL
+	 * register to force the write to complete. It doesn't matter
+	 * what RSL read we do, so we choose CVMX_MIO_BOOT_BIST_STAT
+	 * because it is fast and harmless.
+	 */
+	if (((csr_addr >> 40) & 0x7ffff) == (0x118))
+		cvmx_read64(CVMX_MIO_BOOT_BIST_STAT);
+}
+
+static inline void cvmx_writeq_csr(void __iomem *csr_addr, uint64_t val)
+{
+	cvmx_write_csr((__force uint64_t)csr_addr, val);
+}
+
+static inline void cvmx_write_io(uint64_t io_addr, uint64_t val)
+{
+	cvmx_write64(io_addr, val);
+
+}
+
+static inline uint64_t cvmx_read_csr(uint64_t csr_addr)
+{
+	uint64_t val = cvmx_read64(csr_addr);
+	return val;
+}
+
+static inline uint64_t cvmx_readq_csr(void __iomem *csr_addr)
+{
+	return cvmx_read_csr((__force uint64_t) csr_addr);
+}
+
+static inline void cvmx_send_single(uint64_t data)
+{
+	const uint64_t CVMX_IOBDMA_SENDSINGLE = 0xffffffffffffa200ull;
+	cvmx_write64(CVMX_IOBDMA_SENDSINGLE, data);
+}
+
+static inline void cvmx_read_csr_async(uint64_t scraddr, uint64_t csr_addr)
+{
+	union {
+		uint64_t u64;
+		struct {
+			uint64_t scraddr:8;
+			uint64_t len:8;
+			uint64_t addr:48;
+		} s;
+	} addr;
+	addr.u64 = csr_addr;
+	addr.s.scraddr = scraddr >> 3;
+	addr.s.len = 1;
+	cvmx_send_single(addr.u64);
+}
+
+/* Return true if Octeon is CN38XX pass 1 */
+static inline int cvmx_octeon_is_pass1(void)
+{
+#if OCTEON_IS_COMMON_BINARY()
+	return 0;	/* Pass 1 isn't supported for common binaries */
+#else
+/* Now that we know we're built for a specific model, only check CN38XX */
+#if OCTEON_IS_MODEL(OCTEON_CN38XX)
+	return cvmx_get_proc_id() == OCTEON_CN38XX_PASS1;
+#else
+	return 0;	/* Built for non CN38XX chip, we're not CN38XX pass1 */
+#endif
+#endif
+}
+
+static inline unsigned int cvmx_get_core_num(void)
+{
+	unsigned int core_num;
+	CVMX_RDHWRNV(core_num, 0);
+	return core_num;
+}
+
+/* Maximum # of bits to define core in node */
+#define CVMX_NODE_NO_SHIFT	7
+#define CVMX_NODE_MASK		0x3
+static inline unsigned int cvmx_get_node_num(void)
+{
+	unsigned int core_num = cvmx_get_core_num();
+
+	return (core_num >> CVMX_NODE_NO_SHIFT) & CVMX_NODE_MASK;
+}
+
+static inline unsigned int cvmx_get_local_core_num(void)
+{
+	return cvmx_get_core_num() & ((1 << CVMX_NODE_NO_SHIFT) - 1);
+}
+
+#define CVMX_NODE_BITS         (2)     /* Number of bits to define a node */
+#define CVMX_MAX_NODES         (1 << CVMX_NODE_BITS)
+#define CVMX_NODE_IO_SHIFT     (36)
+#define CVMX_NODE_MEM_SHIFT    (40)
+#define CVMX_NODE_IO_MASK      ((uint64_t)CVMX_NODE_MASK << CVMX_NODE_IO_SHIFT)
+
+static inline void cvmx_write_csr_node(uint64_t node, uint64_t csr_addr,
+				       uint64_t val)
+{
+	uint64_t composite_csr_addr, node_addr;
+
+	node_addr = (node & CVMX_NODE_MASK) << CVMX_NODE_IO_SHIFT;
+	composite_csr_addr = (csr_addr & ~CVMX_NODE_IO_MASK) | node_addr;
+
+	cvmx_write64_uint64(composite_csr_addr, val);
+	if (((csr_addr >> 40) & 0x7ffff) == (0x118))
+		cvmx_read64_uint64(CVMX_MIO_BOOT_BIST_STAT | node_addr);
+}
+
+static inline uint64_t cvmx_read_csr_node(uint64_t node, uint64_t csr_addr)
+{
+	uint64_t node_addr;
+
+	node_addr = (csr_addr & ~CVMX_NODE_IO_MASK) |
+		    (node & CVMX_NODE_MASK) << CVMX_NODE_IO_SHIFT;
+	return cvmx_read_csr(node_addr);
+}
+
+/**
+ * Returns the number of bits set in the provided value.
+ * Simple wrapper for POP instruction.
+ *
+ * @val:    32 bit value to count set bits in
+ *
+ * Returns Number of bits set
+ */
+static inline uint32_t cvmx_pop(uint32_t val)
+{
+	uint32_t pop;
+	CVMX_POP(pop, val);
+	return pop;
+}
+
+/**
+ * Returns the number of bits set in the provided value.
+ * Simple wrapper for DPOP instruction.
+ *
+ * @val:    64 bit value to count set bits in
+ *
+ * Returns Number of bits set
+ */
+static inline int cvmx_dpop(uint64_t val)
+{
+	int pop;
+	CVMX_DPOP(pop, val);
+	return pop;
+}
+
+/**
+ * Provide current cycle counter as a return value
+ *
+ * Returns current cycle counter
+ */
+
+static inline uint64_t cvmx_get_cycle(void)
+{
+	uint64_t cycle;
+	CVMX_RDHWR(cycle, 31);
+	return cycle;
+}
+
+/**
+ * Reads a chip global cycle counter.  This counts CPU cycles since
+ * chip reset.	The counter is 64 bit.
+ * This register does not exist on CN38XX pass 1 silicion
+ *
+ * Returns Global chip cycle count since chip reset.
+ */
+static inline uint64_t cvmx_get_cycle_global(void)
+{
+	if (cvmx_octeon_is_pass1())
+		return 0;
+	else
+		return cvmx_read64(CVMX_IPD_CLK_COUNT);
+}
+
+/**
+ * This macro spins on a field waiting for it to reach a value. It
+ * is common in code to need to wait for a specific field in a CSR
+ * to match a specific value. Conceptually this macro expands to:
+ *
+ * 1) read csr at "address" with a csr typedef of "type"
+ * 2) Check if ("type".s."field" "op" "value")
+ * 3) If #2 isn't true loop to #1 unless too much time has passed.
+ */
+#define CVMX_WAIT_FOR_FIELD64(address, type, field, op, value, timeout_usec)\
+    (									\
+{									\
+	int result;							\
+	do {								\
+		uint64_t done = cvmx_get_cycle() + (uint64_t)timeout_usec * \
+			cvmx_sysinfo_get()->cpu_clock_hz / 1000000;	\
+		type c;							\
+		while (1) {						\
+			c.u64 = cvmx_read_csr(address);			\
+			if ((c.s.field) op(value)) {			\
+				result = 0;				\
+				break;					\
+			} else if (cvmx_get_cycle() > done) {		\
+				result = -1;				\
+				break;					\
+			} else						\
+				__delay(100);				\
+		}							\
+	} while (0);							\
+	result;								\
+})
+
+/***************************************************************************/
+
+/* Return the number of cores available in the chip */
+static inline uint32_t cvmx_octeon_num_cores(void)
+{
+	u64 ciu_fuse_reg;
+	u64 ciu_fuse;
+
+	if (OCTEON_IS_OCTEON3() && !OCTEON_IS_MODEL(OCTEON_CN70XX))
+		ciu_fuse_reg = CVMX_CIU3_FUSE;
+	else
+		ciu_fuse_reg = CVMX_CIU_FUSE;
+	ciu_fuse = cvmx_read_csr(ciu_fuse_reg);
+	return cvmx_dpop(ciu_fuse);
+}
+
+#endif /*  __CVMX_H__  */
diff --git a/arch/mips/include/asm/octeon/octeon-feature.h b/arch/mips/include/asm/octeon/octeon-feature.h
new file mode 100644
index 000000000..a19ca3b27
--- /dev/null
+++ b/arch/mips/include/asm/octeon/octeon-feature.h
@@ -0,0 +1,213 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2008 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+
+/*
+ * File defining checks for different Octeon features.
+ */
+
+#ifndef __OCTEON_FEATURE_H__
+#define __OCTEON_FEATURE_H__
+#include <asm/octeon/cvmx-mio-defs.h>
+#include <asm/octeon/cvmx-rnm-defs.h>
+
+enum octeon_feature {
+	/* CN68XX uses port kinds for packet interface */
+	OCTEON_FEATURE_PKND,
+	/* CN68XX has different fields in word0 - word2 */
+	OCTEON_FEATURE_CN68XX_WQE,
+	/*
+	 * Octeon models in the CN5XXX family and higher support
+	 * atomic add instructions to memory (saa/saad).
+	 */
+	OCTEON_FEATURE_SAAD,
+	/* Does this Octeon support the ZIP offload engine? */
+	OCTEON_FEATURE_ZIP,
+	OCTEON_FEATURE_DORM_CRYPTO,
+	/* Does this Octeon support PCI express? */
+	OCTEON_FEATURE_PCIE,
+	/* Does this Octeon support SRIOs */
+	OCTEON_FEATURE_SRIO,
+	/*  Does this Octeon support Interlaken */
+	OCTEON_FEATURE_ILK,
+	/* Some Octeon models support internal memory for storing
+	 * cryptographic keys */
+	OCTEON_FEATURE_KEY_MEMORY,
+	/* Octeon has a LED controller for banks of external LEDs */
+	OCTEON_FEATURE_LED_CONTROLLER,
+	/* Octeon has a trace buffer */
+	OCTEON_FEATURE_TRA,
+	/* Octeon has a management port */
+	OCTEON_FEATURE_MGMT_PORT,
+	/* Octeon has a raid unit */
+	OCTEON_FEATURE_RAID,
+	/* Octeon has a builtin USB */
+	OCTEON_FEATURE_USB,
+	/* Octeon IPD can run without using work queue entries */
+	OCTEON_FEATURE_NO_WPTR,
+	/* Octeon has DFA state machines */
+	OCTEON_FEATURE_DFA,
+	/* Octeon MDIO block supports clause 45 transactions for 10
+	 * Gig support */
+	OCTEON_FEATURE_MDIO_CLAUSE_45,
+	/*
+	 *  CN52XX and CN56XX used a block named NPEI for PCIe
+	 *  access. Newer chips replaced this with SLI+DPI.
+	 */
+	OCTEON_FEATURE_NPEI,
+	OCTEON_FEATURE_HFA,
+	OCTEON_FEATURE_DFM,
+	OCTEON_FEATURE_CIU2,
+	OCTEON_FEATURE_CIU3,
+	/* Octeon has FPA first seen on 78XX */
+	OCTEON_FEATURE_FPA3,
+	OCTEON_FEATURE_FAU,
+	OCTEON_MAX_FEATURE
+};
+
+enum octeon_feature_bits {
+	OCTEON_HAS_CRYPTO = 0x0001,	/* Crypto acceleration using COP2 */
+};
+extern enum octeon_feature_bits __octeon_feature_bits;
+
+/**
+ * octeon_has_crypto() - Check if this OCTEON has crypto acceleration support.
+ *
+ * Returns: Non-zero if the feature exists. Zero if the feature does not exist.
+ */
+static inline int octeon_has_crypto(void)
+{
+	return __octeon_feature_bits & OCTEON_HAS_CRYPTO;
+}
+
+/**
+ * Determine if the current Octeon supports a specific feature. These
+ * checks have been optimized to be fairly quick, but they should still
+ * be kept out of fast path code.
+ *
+ * @feature: Feature to check for. This should always be a constant so the
+ *		  compiler can remove the switch statement through optimization.
+ *
+ * Returns Non zero if the feature exists. Zero if the feature does not
+ *	   exist.
+ */
+static inline bool octeon_has_feature(enum octeon_feature feature)
+{
+	switch (feature) {
+	case OCTEON_FEATURE_SAAD:
+		return !OCTEON_IS_MODEL(OCTEON_CN3XXX);
+
+	case OCTEON_FEATURE_DORM_CRYPTO:
+		if (OCTEON_IS_MODEL(OCTEON_CN6XXX)) {
+			union cvmx_mio_fus_dat2 fus_2;
+			fus_2.u64 = cvmx_read_csr(CVMX_MIO_FUS_DAT2);
+			return !fus_2.s.nocrypto && !fus_2.s.nomul && fus_2.s.dorm_crypto;
+		} else {
+			return false;
+		}
+
+	case OCTEON_FEATURE_PCIE:
+		return OCTEON_IS_MODEL(OCTEON_CN56XX)
+			|| OCTEON_IS_MODEL(OCTEON_CN52XX)
+			|| OCTEON_IS_MODEL(OCTEON_CN6XXX)
+			|| OCTEON_IS_MODEL(OCTEON_CN7XXX);
+
+	case OCTEON_FEATURE_SRIO:
+		return OCTEON_IS_MODEL(OCTEON_CN63XX)
+			|| OCTEON_IS_MODEL(OCTEON_CN66XX);
+
+	case OCTEON_FEATURE_ILK:
+		return (OCTEON_IS_MODEL(OCTEON_CN68XX));
+
+	case OCTEON_FEATURE_KEY_MEMORY:
+		return OCTEON_IS_MODEL(OCTEON_CN38XX)
+			|| OCTEON_IS_MODEL(OCTEON_CN58XX)
+			|| OCTEON_IS_MODEL(OCTEON_CN56XX)
+			|| OCTEON_IS_MODEL(OCTEON_CN6XXX);
+
+	case OCTEON_FEATURE_LED_CONTROLLER:
+		return OCTEON_IS_MODEL(OCTEON_CN38XX)
+			|| OCTEON_IS_MODEL(OCTEON_CN58XX)
+			|| OCTEON_IS_MODEL(OCTEON_CN56XX);
+
+	case OCTEON_FEATURE_TRA:
+		return !(OCTEON_IS_MODEL(OCTEON_CN30XX)
+			 || OCTEON_IS_MODEL(OCTEON_CN50XX));
+	case OCTEON_FEATURE_MGMT_PORT:
+		return OCTEON_IS_MODEL(OCTEON_CN56XX)
+			|| OCTEON_IS_MODEL(OCTEON_CN52XX)
+			|| OCTEON_IS_MODEL(OCTEON_CN6XXX);
+
+	case OCTEON_FEATURE_RAID:
+		return OCTEON_IS_MODEL(OCTEON_CN56XX)
+			|| OCTEON_IS_MODEL(OCTEON_CN52XX)
+			|| OCTEON_IS_MODEL(OCTEON_CN6XXX);
+
+	case OCTEON_FEATURE_USB:
+		return !(OCTEON_IS_MODEL(OCTEON_CN38XX)
+			 || OCTEON_IS_MODEL(OCTEON_CN58XX));
+
+	case OCTEON_FEATURE_NO_WPTR:
+		return (OCTEON_IS_MODEL(OCTEON_CN56XX)
+			|| OCTEON_IS_MODEL(OCTEON_CN52XX)
+			|| OCTEON_IS_MODEL(OCTEON_CN6XXX))
+			  && !OCTEON_IS_MODEL(OCTEON_CN56XX_PASS1_X)
+			  && !OCTEON_IS_MODEL(OCTEON_CN52XX_PASS1_X);
+
+	case OCTEON_FEATURE_MDIO_CLAUSE_45:
+		return !(OCTEON_IS_MODEL(OCTEON_CN3XXX)
+			 || OCTEON_IS_MODEL(OCTEON_CN58XX)
+			 || OCTEON_IS_MODEL(OCTEON_CN50XX));
+
+	case OCTEON_FEATURE_NPEI:
+		return OCTEON_IS_MODEL(OCTEON_CN56XX)
+			|| OCTEON_IS_MODEL(OCTEON_CN52XX);
+
+	case OCTEON_FEATURE_PKND:
+		return OCTEON_IS_MODEL(OCTEON_CN68XX);
+
+	case OCTEON_FEATURE_CN68XX_WQE:
+		return OCTEON_IS_MODEL(OCTEON_CN68XX);
+
+	case OCTEON_FEATURE_CIU2:
+		return OCTEON_IS_MODEL(OCTEON_CN68XX);
+	case OCTEON_FEATURE_CIU3:
+	case OCTEON_FEATURE_FPA3:
+		return OCTEON_IS_MODEL(OCTEON_CN78XX)
+			|| OCTEON_IS_MODEL(OCTEON_CNF75XX)
+			|| OCTEON_IS_MODEL(OCTEON_CN73XX);
+	case OCTEON_FEATURE_FAU:
+		return !(OCTEON_IS_MODEL(OCTEON_CN78XX)
+			 || OCTEON_IS_MODEL(OCTEON_CNF75XX)
+			 || OCTEON_IS_MODEL(OCTEON_CN73XX));
+
+	default:
+		break;
+	}
+	return false;
+}
+
+#endif /* __OCTEON_FEATURE_H__ */
diff --git a/arch/mips/include/asm/octeon/octeon-model.h b/arch/mips/include/asm/octeon/octeon-model.h
new file mode 100644
index 000000000..6c68517c2
--- /dev/null
+++ b/arch/mips/include/asm/octeon/octeon-model.h
@@ -0,0 +1,409 @@
+/***********************license start***************
+ * Author: Cavium Networks
+ *
+ * Contact: support@caviumnetworks.com
+ * This file is part of the OCTEON SDK
+ *
+ * Copyright (c) 2003-2010 Cavium Networks
+ *
+ * This file is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License, Version 2, as
+ * published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful, but
+ * AS-IS and WITHOUT ANY WARRANTY; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, TITLE, or
+ * NONINFRINGEMENT.  See the GNU General Public License for more
+ * details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this file; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ * or visit http://www.gnu.org/licenses/.
+ *
+ * This file may also be available under a different license from Cavium.
+ * Contact Cavium Networks for more information
+ ***********************license end**************************************/
+#ifndef __OCTEON_MODEL_H__
+#define __OCTEON_MODEL_H__
+
+/*
+ * The defines below should be used with the OCTEON_IS_MODEL() macro
+ * to determine what model of chip the software is running on.	Models
+ * ending in 'XX' match multiple models (families), while specific
+ * models match only that model.  If a pass (revision) is specified,
+ * then only that revision will be matched.  Care should be taken when
+ * checking for both specific models and families that the specific
+ * models are checked for first.  While these defines are similar to
+ * the processor ID, they are not intended to be used by anything
+ * other that the OCTEON_IS_MODEL framework, and the values are
+ * subject to change at anytime without notice.
+ *
+ * NOTE: only the OCTEON_IS_MODEL() macro/function and the OCTEON_CN*
+ * macros should be used outside of this file.	All other macros are
+ * for internal use only, and may change without notice.
+ */
+
+#define OCTEON_FAMILY_MASK	0x00ffff00
+#define OCTEON_PRID_MASK	0x00ffffff
+
+/* Flag bits in top byte */
+/* Ignores revision in model checks */
+#define OM_IGNORE_REVISION	  0x01000000
+/* Check submodels */
+#define OM_CHECK_SUBMODEL	  0x02000000
+/* Match all models previous than the one specified */
+#define OM_MATCH_PREVIOUS_MODELS  0x04000000
+/* Ignores the minor revison on newer parts */
+#define OM_IGNORE_MINOR_REVISION  0x08000000
+#define OM_FLAG_MASK		  0xff000000
+
+/* Match all cn5XXX Octeon models. */
+#define OM_MATCH_5XXX_FAMILY_MODELS	0x20000000
+/* Match all cn6XXX Octeon models. */
+#define OM_MATCH_6XXX_FAMILY_MODELS	0x40000000
+/* Match all cnf7XXX Octeon models. */
+#define OM_MATCH_F7XXX_FAMILY_MODELS	0x80000000
+/* Match all cn7XXX Octeon models. */
+#define OM_MATCH_7XXX_FAMILY_MODELS     0x10000000
+#define OM_MATCH_FAMILY_MODELS		(OM_MATCH_5XXX_FAMILY_MODELS |	\
+					 OM_MATCH_6XXX_FAMILY_MODELS |	\
+					 OM_MATCH_F7XXX_FAMILY_MODELS | \
+					 OM_MATCH_7XXX_FAMILY_MODELS)
+/*
+ * CN7XXX models with new revision encoding
+ */
+
+#define OCTEON_CNF75XX_PASS1_0	0x000d9800
+#define OCTEON_CNF75XX		(OCTEON_CNF75XX_PASS1_0 | OM_IGNORE_REVISION)
+#define OCTEON_CNF75XX_PASS1_X	(OCTEON_CNF75XX_PASS1_0 | OM_IGNORE_MINOR_REVISION)
+
+#define OCTEON_CN73XX_PASS1_0	0x000d9700
+#define OCTEON_CN73XX_PASS1_1	0x000d9701
+#define OCTEON_CN73XX		(OCTEON_CN73XX_PASS1_0 | OM_IGNORE_REVISION)
+#define OCTEON_CN73XX_PASS1_X	(OCTEON_CN73XX_PASS1_0 | \
+				 OM_IGNORE_MINOR_REVISION)
+
+#define OCTEON_CN70XX_PASS1_0	0x000d9600
+#define OCTEON_CN70XX_PASS1_1	0x000d9601
+#define OCTEON_CN70XX_PASS1_2	0x000d9602
+
+#define OCTEON_CN70XX_PASS2_0	0x000d9608
+
+#define OCTEON_CN70XX		(OCTEON_CN70XX_PASS1_0 | OM_IGNORE_REVISION)
+#define OCTEON_CN70XX_PASS1_X	(OCTEON_CN70XX_PASS1_0 | \
+				 OM_IGNORE_MINOR_REVISION)
+#define OCTEON_CN70XX_PASS2_X	(OCTEON_CN70XX_PASS2_0 | \
+				 OM_IGNORE_MINOR_REVISION)
+
+#define OCTEON_CN71XX		OCTEON_CN70XX
+
+#define OCTEON_CN78XX_PASS1_0	0x000d9500
+#define OCTEON_CN78XX_PASS1_1	0x000d9501
+#define OCTEON_CN78XX_PASS2_0	0x000d9508
+
+#define OCTEON_CN78XX		(OCTEON_CN78XX_PASS1_0 | OM_IGNORE_REVISION)
+#define OCTEON_CN78XX_PASS1_X	(OCTEON_CN78XX_PASS1_0 | \
+				 OM_IGNORE_MINOR_REVISION)
+#define OCTEON_CN78XX_PASS2_X	(OCTEON_CN78XX_PASS2_0 | \
+				 OM_IGNORE_MINOR_REVISION)
+
+#define OCTEON_CN76XX		(0x000d9540 | OM_CHECK_SUBMODEL)
+
+/*
+ * CNF7XXX models with new revision encoding
+ */
+#define OCTEON_CNF71XX_PASS1_0	0x000d9400
+#define OCTEON_CNF71XX_PASS1_1  0x000d9401
+
+#define OCTEON_CNF71XX		(OCTEON_CNF71XX_PASS1_0 | OM_IGNORE_REVISION)
+#define OCTEON_CNF71XX_PASS1_X	(OCTEON_CNF71XX_PASS1_0 | OM_IGNORE_MINOR_REVISION)
+
+/*
+ * CN6XXX models with new revision encoding
+ */
+#define OCTEON_CN68XX_PASS1_0	0x000d9100
+#define OCTEON_CN68XX_PASS1_1	0x000d9101
+#define OCTEON_CN68XX_PASS1_2	0x000d9102
+#define OCTEON_CN68XX_PASS2_0	0x000d9108
+#define OCTEON_CN68XX_PASS2_1   0x000d9109
+#define OCTEON_CN68XX_PASS2_2   0x000d910a
+
+#define OCTEON_CN68XX		(OCTEON_CN68XX_PASS2_0 | OM_IGNORE_REVISION)
+#define OCTEON_CN68XX_PASS1_X	(OCTEON_CN68XX_PASS1_0 | OM_IGNORE_MINOR_REVISION)
+#define OCTEON_CN68XX_PASS2_X	(OCTEON_CN68XX_PASS2_0 | OM_IGNORE_MINOR_REVISION)
+
+#define OCTEON_CN68XX_PASS1	OCTEON_CN68XX_PASS1_X
+#define OCTEON_CN68XX_PASS2	OCTEON_CN68XX_PASS2_X
+
+#define OCTEON_CN66XX_PASS1_0	0x000d9200
+#define OCTEON_CN66XX_PASS1_2	0x000d9202
+
+#define OCTEON_CN66XX		(OCTEON_CN66XX_PASS1_0 | OM_IGNORE_REVISION)
+#define OCTEON_CN66XX_PASS1_X	(OCTEON_CN66XX_PASS1_0 | OM_IGNORE_MINOR_REVISION)
+
+#define OCTEON_CN63XX_PASS1_0	0x000d9000
+#define OCTEON_CN63XX_PASS1_1	0x000d9001
+#define OCTEON_CN63XX_PASS1_2	0x000d9002
+#define OCTEON_CN63XX_PASS2_0	0x000d9008
+#define OCTEON_CN63XX_PASS2_1	0x000d9009
+#define OCTEON_CN63XX_PASS2_2	0x000d900a
+
+#define OCTEON_CN63XX		(OCTEON_CN63XX_PASS2_0 | OM_IGNORE_REVISION)
+#define OCTEON_CN63XX_PASS1_X	(OCTEON_CN63XX_PASS1_0 | OM_IGNORE_MINOR_REVISION)
+#define OCTEON_CN63XX_PASS2_X	(OCTEON_CN63XX_PASS2_0 | OM_IGNORE_MINOR_REVISION)
+
+/* CN62XX is same as CN63XX with 1 MB cache */
+#define OCTEON_CN62XX           OCTEON_CN63XX
+
+#define OCTEON_CN61XX_PASS1_0	0x000d9300
+#define OCTEON_CN61XX_PASS1_1   0x000d9301
+
+#define OCTEON_CN61XX		(OCTEON_CN61XX_PASS1_0 | OM_IGNORE_REVISION)
+#define OCTEON_CN61XX_PASS1_X	(OCTEON_CN61XX_PASS1_0 | OM_IGNORE_MINOR_REVISION)
+
+/* CN60XX is same as CN61XX with 512 KB cache */
+#define OCTEON_CN60XX           OCTEON_CN61XX
+
+/*
+ * CN5XXX models with new revision encoding
+ */
+#define OCTEON_CN58XX_PASS1_0	0x000d0300
+#define OCTEON_CN58XX_PASS1_1	0x000d0301
+#define OCTEON_CN58XX_PASS1_2	0x000d0303
+#define OCTEON_CN58XX_PASS2_0	0x000d0308
+#define OCTEON_CN58XX_PASS2_1	0x000d0309
+#define OCTEON_CN58XX_PASS2_2	0x000d030a
+#define OCTEON_CN58XX_PASS2_3	0x000d030b
+
+#define OCTEON_CN58XX		(OCTEON_CN58XX_PASS2_0 | OM_IGNORE_REVISION)
+#define OCTEON_CN58XX_PASS1_X	(OCTEON_CN58XX_PASS1_0 | OM_IGNORE_MINOR_REVISION)
+#define OCTEON_CN58XX_PASS2_X	(OCTEON_CN58XX_PASS2_0 | OM_IGNORE_MINOR_REVISION)
+#define OCTEON_CN58XX_PASS1	OCTEON_CN58XX_PASS1_X
+#define OCTEON_CN58XX_PASS2	OCTEON_CN58XX_PASS2_X
+
+#define OCTEON_CN56XX_PASS1_0	0x000d0400
+#define OCTEON_CN56XX_PASS1_1	0x000d0401
+#define OCTEON_CN56XX_PASS2_0	0x000d0408
+#define OCTEON_CN56XX_PASS2_1	0x000d0409
+
+#define OCTEON_CN56XX		(OCTEON_CN56XX_PASS2_0 | OM_IGNORE_REVISION)
+#define OCTEON_CN56XX_PASS1_X	(OCTEON_CN56XX_PASS1_0 | OM_IGNORE_MINOR_REVISION)
+#define OCTEON_CN56XX_PASS2_X	(OCTEON_CN56XX_PASS2_0 | OM_IGNORE_MINOR_REVISION)
+#define OCTEON_CN56XX_PASS1	OCTEON_CN56XX_PASS1_X
+#define OCTEON_CN56XX_PASS2	OCTEON_CN56XX_PASS2_X
+
+#define OCTEON_CN57XX		OCTEON_CN56XX
+#define OCTEON_CN57XX_PASS1	OCTEON_CN56XX_PASS1
+#define OCTEON_CN57XX_PASS2	OCTEON_CN56XX_PASS2
+
+#define OCTEON_CN55XX		OCTEON_CN56XX
+#define OCTEON_CN55XX_PASS1	OCTEON_CN56XX_PASS1
+#define OCTEON_CN55XX_PASS2	OCTEON_CN56XX_PASS2
+
+#define OCTEON_CN54XX		OCTEON_CN56XX
+#define OCTEON_CN54XX_PASS1	OCTEON_CN56XX_PASS1
+#define OCTEON_CN54XX_PASS2	OCTEON_CN56XX_PASS2
+
+#define OCTEON_CN50XX_PASS1_0	0x000d0600
+
+#define OCTEON_CN50XX		(OCTEON_CN50XX_PASS1_0 | OM_IGNORE_REVISION)
+#define OCTEON_CN50XX_PASS1_X	(OCTEON_CN50XX_PASS1_0 | OM_IGNORE_MINOR_REVISION)
+#define OCTEON_CN50XX_PASS1	OCTEON_CN50XX_PASS1_X
+
+/*
+ * NOTE: Octeon CN5000F model is not identifiable using the
+ * OCTEON_IS_MODEL() functions, but are treated as CN50XX.
+ */
+
+#define OCTEON_CN52XX_PASS1_0	0x000d0700
+#define OCTEON_CN52XX_PASS2_0	0x000d0708
+
+#define OCTEON_CN52XX		(OCTEON_CN52XX_PASS2_0 | OM_IGNORE_REVISION)
+#define OCTEON_CN52XX_PASS1_X	(OCTEON_CN52XX_PASS1_0 | OM_IGNORE_MINOR_REVISION)
+#define OCTEON_CN52XX_PASS2_X	(OCTEON_CN52XX_PASS2_0 | OM_IGNORE_MINOR_REVISION)
+#define OCTEON_CN52XX_PASS1	OCTEON_CN52XX_PASS1_X
+#define OCTEON_CN52XX_PASS2	OCTEON_CN52XX_PASS2_X
+
+/*
+ * CN3XXX models with old revision enconding
+ */
+#define OCTEON_CN38XX_PASS1	0x000d0000
+#define OCTEON_CN38XX_PASS2	0x000d0001
+#define OCTEON_CN38XX_PASS3	0x000d0003
+#define OCTEON_CN38XX		(OCTEON_CN38XX_PASS3 | OM_IGNORE_REVISION)
+
+#define OCTEON_CN36XX		OCTEON_CN38XX
+#define OCTEON_CN36XX_PASS2	OCTEON_CN38XX_PASS2
+#define OCTEON_CN36XX_PASS3	OCTEON_CN38XX_PASS3
+
+/* The OCTEON_CN31XX matches CN31XX models and the CN3020 */
+#define OCTEON_CN31XX_PASS1	0x000d0100
+#define OCTEON_CN31XX_PASS1_1	0x000d0102
+#define OCTEON_CN31XX		(OCTEON_CN31XX_PASS1 | OM_IGNORE_REVISION)
+
+/*
+ * This model is only used for internal checks, it is not a valid
+ * model for the OCTEON_MODEL environment variable.  This matches the
+ * CN3010 and CN3005 but NOT the CN3020.
+ */
+#define OCTEON_CN30XX_PASS1	0x000d0200
+#define OCTEON_CN30XX_PASS1_1	0x000d0202
+#define OCTEON_CN30XX		(OCTEON_CN30XX_PASS1 | OM_IGNORE_REVISION)
+
+#define OCTEON_CN3005_PASS1	(0x000d0210 | OM_CHECK_SUBMODEL)
+#define OCTEON_CN3005_PASS1_0	(0x000d0210 | OM_CHECK_SUBMODEL)
+#define OCTEON_CN3005_PASS1_1	(0x000d0212 | OM_CHECK_SUBMODEL)
+#define OCTEON_CN3005		(OCTEON_CN3005_PASS1 | OM_IGNORE_REVISION | OM_CHECK_SUBMODEL)
+
+#define OCTEON_CN3010_PASS1	(0x000d0200 | OM_CHECK_SUBMODEL)
+#define OCTEON_CN3010_PASS1_0	(0x000d0200 | OM_CHECK_SUBMODEL)
+#define OCTEON_CN3010_PASS1_1	(0x000d0202 | OM_CHECK_SUBMODEL)
+#define OCTEON_CN3010		(OCTEON_CN3010_PASS1 | OM_IGNORE_REVISION | OM_CHECK_SUBMODEL)
+
+#define OCTEON_CN3020_PASS1	(0x000d0110 | OM_CHECK_SUBMODEL)
+#define OCTEON_CN3020_PASS1_0	(0x000d0110 | OM_CHECK_SUBMODEL)
+#define OCTEON_CN3020_PASS1_1	(0x000d0112 | OM_CHECK_SUBMODEL)
+#define OCTEON_CN3020		(OCTEON_CN3020_PASS1 | OM_IGNORE_REVISION | OM_CHECK_SUBMODEL)
+
+/*
+ * This matches the complete family of CN3xxx CPUs, and not subsequent
+ * models
+ */
+#define OCTEON_CN3XXX		(OCTEON_CN58XX_PASS1_0 | OM_MATCH_PREVIOUS_MODELS | OM_IGNORE_REVISION)
+#define OCTEON_CN5XXX		(OCTEON_CN58XX_PASS1_0 | OM_MATCH_5XXX_FAMILY_MODELS)
+#define OCTEON_CN6XXX		(OCTEON_CN63XX_PASS1_0 | OM_MATCH_6XXX_FAMILY_MODELS)
+#define OCTEON_CNF7XXX		(OCTEON_CNF71XX_PASS1_0 | \
+				 OM_MATCH_F7XXX_FAMILY_MODELS)
+#define OCTEON_CN7XXX		(OCTEON_CN78XX_PASS1_0 | \
+				 OM_MATCH_7XXX_FAMILY_MODELS)
+
+/* The revision byte (low byte) has two different encodings.
+ * CN3XXX:
+ *
+ *     bits
+ *     <7:5>: reserved (0)
+ *     <4>:   alternate package
+ *     <3:0>: revision
+ *
+ * CN5XXX and older models:
+ *
+ *     bits
+ *     <7>:   reserved (0)
+ *     <6>:   alternate package
+ *     <5:3>: major revision
+ *     <2:0>: minor revision
+ *
+ */
+
+/* Masks used for the various types of model/family/revision matching */
+#define OCTEON_38XX_FAMILY_MASK	     0x00ffff00
+#define OCTEON_38XX_FAMILY_REV_MASK  0x00ffff0f
+#define OCTEON_38XX_MODEL_MASK	     0x00ffff10
+#define OCTEON_38XX_MODEL_REV_MASK   (OCTEON_38XX_FAMILY_REV_MASK | OCTEON_38XX_MODEL_MASK)
+
+/* CN5XXX and later use different layout of bits in the revision ID field */
+#define OCTEON_58XX_FAMILY_MASK	     OCTEON_38XX_FAMILY_MASK
+#define OCTEON_58XX_FAMILY_REV_MASK  0x00ffff3f
+#define OCTEON_58XX_MODEL_MASK	     0x00ffff40
+#define OCTEON_58XX_MODEL_REV_MASK   (OCTEON_58XX_FAMILY_REV_MASK | OCTEON_58XX_MODEL_MASK)
+#define OCTEON_58XX_MODEL_MINOR_REV_MASK (OCTEON_58XX_MODEL_REV_MASK & 0x00ffff38)
+#define OCTEON_5XXX_MODEL_MASK	     0x00ff0fc0
+
+static inline uint32_t cvmx_get_proc_id(void) __attribute__ ((pure));
+static inline uint64_t cvmx_read_csr(uint64_t csr_addr);
+
+#define __OCTEON_MATCH_MASK__(x, y, z) (((x) & (z)) == ((y) & (z)))
+
+/*
+ * __OCTEON_IS_MODEL_COMPILE__(arg_model, chip_model)
+ * returns true if chip_model is identical or belong to the OCTEON
+ * model group specified in arg_model.
+ */
+/* NOTE: This for internal use only! */
+#define __OCTEON_IS_MODEL_COMPILE__(arg_model, chip_model)		\
+((((arg_model & OCTEON_38XX_FAMILY_MASK) < OCTEON_CN58XX_PASS1_0)  && ( \
+		((((arg_model) & (OM_FLAG_MASK)) == (OM_IGNORE_REVISION | OM_CHECK_SUBMODEL)) \
+			&& __OCTEON_MATCH_MASK__((chip_model), (arg_model), OCTEON_38XX_MODEL_MASK)) || \
+		((((arg_model) & (OM_FLAG_MASK)) == 0)			\
+			&& __OCTEON_MATCH_MASK__((chip_model), (arg_model), OCTEON_38XX_FAMILY_REV_MASK)) || \
+		((((arg_model) & (OM_FLAG_MASK)) == OM_IGNORE_REVISION) \
+			&& __OCTEON_MATCH_MASK__((chip_model), (arg_model), OCTEON_38XX_FAMILY_MASK)) || \
+		((((arg_model) & (OM_FLAG_MASK)) == OM_CHECK_SUBMODEL)	\
+			&& __OCTEON_MATCH_MASK__((chip_model), (arg_model), OCTEON_38XX_MODEL_REV_MASK)) || \
+		((((arg_model) & (OM_MATCH_PREVIOUS_MODELS)) == OM_MATCH_PREVIOUS_MODELS) \
+			&& (((chip_model) & OCTEON_38XX_MODEL_MASK) < ((arg_model) & OCTEON_38XX_MODEL_MASK))) \
+		)) ||							\
+	(((arg_model & OCTEON_38XX_FAMILY_MASK) >= OCTEON_CN58XX_PASS1_0)  && ( \
+		((((arg_model) & (OM_FLAG_MASK)) == (OM_IGNORE_REVISION | OM_CHECK_SUBMODEL)) \
+			&& __OCTEON_MATCH_MASK__((chip_model), (arg_model), OCTEON_58XX_MODEL_MASK)) || \
+		((((arg_model) & (OM_FLAG_MASK)) == 0)			\
+			&& __OCTEON_MATCH_MASK__((chip_model), (arg_model), OCTEON_58XX_FAMILY_REV_MASK)) || \
+		((((arg_model) & (OM_FLAG_MASK)) == OM_IGNORE_MINOR_REVISION) \
+			&& __OCTEON_MATCH_MASK__((chip_model), (arg_model), OCTEON_58XX_MODEL_MINOR_REV_MASK)) || \
+		((((arg_model) & (OM_FLAG_MASK)) == OM_IGNORE_REVISION) \
+			&& __OCTEON_MATCH_MASK__((chip_model), (arg_model), OCTEON_58XX_FAMILY_MASK)) || \
+		((((arg_model) & (OM_FLAG_MASK)) == OM_CHECK_SUBMODEL)	\
+			&& __OCTEON_MATCH_MASK__((chip_model), (arg_model), OCTEON_58XX_MODEL_MASK)) || \
+		((((arg_model) & (OM_MATCH_5XXX_FAMILY_MODELS)) == OM_MATCH_5XXX_FAMILY_MODELS) \
+			&& ((chip_model & OCTEON_PRID_MASK) >= OCTEON_CN58XX_PASS1_0) \
+			&& ((chip_model & OCTEON_PRID_MASK) < OCTEON_CN63XX_PASS1_0)) || \
+		((((arg_model) & (OM_MATCH_6XXX_FAMILY_MODELS)) == OM_MATCH_6XXX_FAMILY_MODELS) \
+			&& ((chip_model & OCTEON_PRID_MASK) >= OCTEON_CN63XX_PASS1_0) \
+			&& ((chip_model & OCTEON_PRID_MASK) < OCTEON_CNF71XX_PASS1_0)) || \
+		((((arg_model) & (OM_MATCH_F7XXX_FAMILY_MODELS)) == OM_MATCH_F7XXX_FAMILY_MODELS) \
+			&& ((chip_model & OCTEON_PRID_MASK) >= OCTEON_CNF71XX_PASS1_0) \
+			&& ((chip_model & OCTEON_PRID_MASK) < OCTEON_CN78XX_PASS1_0)) || \
+		((((arg_model) & (OM_MATCH_7XXX_FAMILY_MODELS)) == OM_MATCH_7XXX_FAMILY_MODELS) \
+			&& ((chip_model & OCTEON_PRID_MASK) >= OCTEON_CN78XX_PASS1_0)) || \
+		((((arg_model) & (OM_MATCH_PREVIOUS_MODELS)) == OM_MATCH_PREVIOUS_MODELS) \
+			&& (((chip_model) & OCTEON_58XX_MODEL_MASK) < ((arg_model) & OCTEON_58XX_MODEL_MASK))) \
+		)))
+
+/* NOTE: This for internal use only!!!!! */
+static inline int __octeon_is_model_runtime__(uint32_t model)
+{
+	uint32_t cpuid = cvmx_get_proc_id();
+
+	return __OCTEON_IS_MODEL_COMPILE__(model, cpuid);
+}
+
+/*
+ * The OCTEON_IS_MODEL macro should be used for all Octeon model checking done
+ * in a program.
+ * This should be kept runtime if at all possible  and must be conditionalized
+ * with OCTEON_IS_COMMON_BINARY() if runtime checking support is required.
+ *
+ * Use of the macro in preprocessor directives ( #if OCTEON_IS_MODEL(...) )
+ * is NOT SUPPORTED, and should be replaced with CVMX_COMPILED_FOR()
+ * I.e.:
+ *  #if OCTEON_IS_MODEL(OCTEON_CN56XX)	->  #if CVMX_COMPILED_FOR(OCTEON_CN56XX)
+ */
+#define OCTEON_IS_MODEL(x) __octeon_is_model_runtime__(x)
+#define OCTEON_IS_COMMON_BINARY() 1
+#undef OCTEON_MODEL
+
+#define OCTEON_IS_OCTEON1()	OCTEON_IS_MODEL(OCTEON_CN3XXX)
+#define OCTEON_IS_OCTEONPLUS()	OCTEON_IS_MODEL(OCTEON_CN5XXX)
+#define OCTEON_IS_OCTEON2()						\
+	(OCTEON_IS_MODEL(OCTEON_CN6XXX) || OCTEON_IS_MODEL(OCTEON_CNF71XX))
+
+#define OCTEON_IS_OCTEON3()	OCTEON_IS_MODEL(OCTEON_CN7XXX)
+
+#define OCTEON_IS_OCTEON1PLUS()	(OCTEON_IS_OCTEON1() || OCTEON_IS_OCTEONPLUS())
+
+const char *__init octeon_model_get_string(uint32_t chip_id);
+
+/*
+ * Return the octeon family, i.e., ProcessorID of the PrID register.
+ *
+ * @return the octeon family on success, ((unint32_t)-1) on error.
+ */
+static inline uint32_t cvmx_get_octeon_family(void)
+{
+	return cvmx_get_proc_id() & OCTEON_FAMILY_MASK;
+}
+
+#include <asm/octeon/octeon-feature.h>
+
+#endif /* __OCTEON_MODEL_H__ */
diff --git a/arch/mips/include/asm/octeon/octeon.h b/arch/mips/include/asm/octeon/octeon.h
new file mode 100644
index 000000000..5c1d726c7
--- /dev/null
+++ b/arch/mips/include/asm/octeon/octeon.h
@@ -0,0 +1,364 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2004-2008 Cavium Networks
+ */
+#ifndef __ASM_OCTEON_OCTEON_H
+#define __ASM_OCTEON_OCTEON_H
+
+#include <asm/octeon/cvmx.h>
+#include <asm/bitfield.h>
+
+extern uint64_t octeon_bootmem_alloc_range_phys(uint64_t size,
+						uint64_t alignment,
+						uint64_t min_addr,
+						uint64_t max_addr,
+						int do_locking);
+extern void *octeon_bootmem_alloc(uint64_t size, uint64_t alignment,
+				  int do_locking);
+extern void *octeon_bootmem_alloc_range(uint64_t size, uint64_t alignment,
+					uint64_t min_addr, uint64_t max_addr,
+					int do_locking);
+extern void *octeon_bootmem_alloc_named(uint64_t size, uint64_t alignment,
+					char *name);
+extern void *octeon_bootmem_alloc_named_range(uint64_t size, uint64_t min_addr,
+					      uint64_t max_addr, uint64_t align,
+					      char *name);
+extern void *octeon_bootmem_alloc_named_address(uint64_t size, uint64_t address,
+						char *name);
+extern int octeon_bootmem_free_named(char *name);
+extern void octeon_bootmem_lock(void);
+extern void octeon_bootmem_unlock(void);
+
+extern int octeon_is_simulation(void);
+extern int octeon_is_pci_host(void);
+extern int octeon_usb_is_ref_clk(void);
+extern uint64_t octeon_get_clock_rate(void);
+extern u64 octeon_get_io_clock_rate(void);
+extern const char *octeon_board_type_string(void);
+extern const char *octeon_get_pci_interrupts(void);
+extern int octeon_get_southbridge_interrupt(void);
+extern int octeon_get_boot_coremask(void);
+extern int octeon_get_boot_num_arguments(void);
+extern const char *octeon_get_boot_argument(int arg);
+extern void octeon_user_io_init(void);
+
+extern void octeon_init_cvmcount(void);
+extern void octeon_setup_delays(void);
+extern void octeon_io_clk_delay(unsigned long);
+
+#define OCTEON_ARGV_MAX_ARGS	64
+#define OCTEON_SERIAL_LEN	20
+
+struct octeon_boot_descriptor {
+#ifdef __BIG_ENDIAN_BITFIELD
+	/* Start of block referenced by assembly code - do not change! */
+	uint32_t desc_version;
+	uint32_t desc_size;
+	uint64_t stack_top;
+	uint64_t heap_base;
+	uint64_t heap_end;
+	/* Only used by bootloader */
+	uint64_t entry_point;
+	uint64_t desc_vaddr;
+	/* End of This block referenced by assembly code - do not change! */
+	uint32_t exception_base_addr;
+	uint32_t stack_size;
+	uint32_t heap_size;
+	/* Argc count for application. */
+	uint32_t argc;
+	uint32_t argv[OCTEON_ARGV_MAX_ARGS];
+
+#define	 BOOT_FLAG_INIT_CORE		(1 << 0)
+#define	 OCTEON_BL_FLAG_DEBUG		(1 << 1)
+#define	 OCTEON_BL_FLAG_NO_MAGIC	(1 << 2)
+	/* If set, use uart1 for console */
+#define	 OCTEON_BL_FLAG_CONSOLE_UART1	(1 << 3)
+	/* If set, use PCI console */
+#define	 OCTEON_BL_FLAG_CONSOLE_PCI	(1 << 4)
+	/* Call exit on break on serial port */
+#define	 OCTEON_BL_FLAG_BREAK		(1 << 5)
+
+	uint32_t flags;
+	uint32_t core_mask;
+	/* DRAM size in megabyes. */
+	uint32_t dram_size;
+	/* physical address of free memory descriptor block. */
+	uint32_t phy_mem_desc_addr;
+	/* used to pass flags from app to debugger. */
+	uint32_t debugger_flags_base_addr;
+	/* CPU clock speed, in hz. */
+	uint32_t eclock_hz;
+	/* DRAM clock speed, in hz. */
+	uint32_t dclock_hz;
+	/* SPI4 clock in hz. */
+	uint32_t spi_clock_hz;
+	uint16_t board_type;
+	uint8_t board_rev_major;
+	uint8_t board_rev_minor;
+	uint16_t chip_type;
+	uint8_t chip_rev_major;
+	uint8_t chip_rev_minor;
+	char board_serial_number[OCTEON_SERIAL_LEN];
+	uint8_t mac_addr_base[6];
+	uint8_t mac_addr_count;
+	uint64_t cvmx_desc_vaddr;
+#else
+	uint32_t desc_size;
+	uint32_t desc_version;
+	uint64_t stack_top;
+	uint64_t heap_base;
+	uint64_t heap_end;
+	/* Only used by bootloader */
+	uint64_t entry_point;
+	uint64_t desc_vaddr;
+	/* End of This block referenced by assembly code - do not change! */
+	uint32_t stack_size;
+	uint32_t exception_base_addr;
+	uint32_t argc;
+	uint32_t heap_size;
+	/*
+	 * Argc count for application.
+	 * Warning low bit scrambled in little-endian.
+	 */
+	uint32_t argv[OCTEON_ARGV_MAX_ARGS];
+
+#define  BOOT_FLAG_INIT_CORE		(1 << 0)
+#define  OCTEON_BL_FLAG_DEBUG		(1 << 1)
+#define  OCTEON_BL_FLAG_NO_MAGIC	(1 << 2)
+	/* If set, use uart1 for console */
+#define  OCTEON_BL_FLAG_CONSOLE_UART1	(1 << 3)
+	/* If set, use PCI console */
+#define  OCTEON_BL_FLAG_CONSOLE_PCI	(1 << 4)
+	/* Call exit on break on serial port */
+#define  OCTEON_BL_FLAG_BREAK		(1 << 5)
+
+	uint32_t core_mask;
+	uint32_t flags;
+	/* physical address of free memory descriptor block. */
+	uint32_t phy_mem_desc_addr;
+	/* DRAM size in megabyes. */
+	uint32_t dram_size;
+	/* CPU clock speed, in hz. */
+	uint32_t eclock_hz;
+	/* used to pass flags from app to debugger. */
+	uint32_t debugger_flags_base_addr;
+	/* SPI4 clock in hz. */
+	uint32_t spi_clock_hz;
+	/* DRAM clock speed, in hz. */
+	uint32_t dclock_hz;
+	uint8_t chip_rev_minor;
+	uint8_t chip_rev_major;
+	uint16_t chip_type;
+	uint8_t board_rev_minor;
+	uint8_t board_rev_major;
+	uint16_t board_type;
+
+	uint64_t unused1[4]; /* Not even filled in by bootloader. */
+
+	uint64_t cvmx_desc_vaddr;
+#endif
+};
+
+union octeon_cvmemctl {
+	uint64_t u64;
+	struct {
+		/* RO 1 = BIST fail, 0 = BIST pass */
+		__BITFIELD_FIELD(uint64_t tlbbist:1,
+		/* RO 1 = BIST fail, 0 = BIST pass */
+		__BITFIELD_FIELD(uint64_t l1cbist:1,
+		/* RO 1 = BIST fail, 0 = BIST pass */
+		__BITFIELD_FIELD(uint64_t l1dbist:1,
+		/* RO 1 = BIST fail, 0 = BIST pass */
+		__BITFIELD_FIELD(uint64_t dcmbist:1,
+		/* RO 1 = BIST fail, 0 = BIST pass */
+		__BITFIELD_FIELD(uint64_t ptgbist:1,
+		/* RO 1 = BIST fail, 0 = BIST pass */
+		__BITFIELD_FIELD(uint64_t wbfbist:1,
+		/* Reserved */
+		__BITFIELD_FIELD(uint64_t reserved:17,
+		/* OCTEON II - TLB replacement policy: 0 = bitmask LRU; 1 = NLU.
+		 * This field selects between the TLB replacement policies:
+		 * bitmask LRU or NLU. Bitmask LRU maintains a mask of
+		 * recently used TLB entries and avoids them as new entries
+		 * are allocated. NLU simply guarantees that the next
+		 * allocation is not the last used TLB entry. */
+		__BITFIELD_FIELD(uint64_t tlbnlu:1,
+		/* OCTEON II - Selects the bit in the counter used for
+		 * releasing a PAUSE. This counter trips every 2(8+PAUSETIME)
+		 * cycles. If not already released, the cnMIPS II core will
+		 * always release a given PAUSE instruction within
+		 * 2(8+PAUSETIME). If the counter trip happens to line up,
+		 * the cnMIPS II core may release the PAUSE instantly. */
+		__BITFIELD_FIELD(uint64_t pausetime:3,
+		/* OCTEON II - This field is an extension of
+		 * CvmMemCtl[DIDTTO] */
+		__BITFIELD_FIELD(uint64_t didtto2:1,
+		/* R/W If set, marked write-buffer entries time out
+		 * the same as other entries; if clear, marked
+		 * write-buffer entries use the maximum timeout. */
+		__BITFIELD_FIELD(uint64_t dismarkwblongto:1,
+		/* R/W If set, a merged store does not clear the
+		 * write-buffer entry timeout state. */
+		__BITFIELD_FIELD(uint64_t dismrgclrwbto:1,
+		/* R/W Two bits that are the MSBs of the resultant
+		 * CVMSEG LM word location for an IOBDMA. The other 8
+		 * bits come from the SCRADDR field of the IOBDMA. */
+		__BITFIELD_FIELD(uint64_t iobdmascrmsb:2,
+		/* R/W If set, SYNCWS and SYNCS only order marked
+		 * stores; if clear, SYNCWS and SYNCS only order
+		 * unmarked stores. SYNCWSMARKED has no effect when
+		 * DISSYNCWS is set. */
+		__BITFIELD_FIELD(uint64_t syncwsmarked:1,
+		/* R/W If set, SYNCWS acts as SYNCW and SYNCS acts as
+		 * SYNC. */
+		__BITFIELD_FIELD(uint64_t dissyncws:1,
+		/* R/W If set, no stall happens on write buffer
+		 * full. */
+		__BITFIELD_FIELD(uint64_t diswbfst:1,
+		/* R/W If set (and SX set), supervisor-level
+		 * loads/stores can use XKPHYS addresses with
+		 * VA<48>==0 */
+		__BITFIELD_FIELD(uint64_t xkmemenas:1,
+		/* R/W If set (and UX set), user-level loads/stores
+		 * can use XKPHYS addresses with VA<48>==0 */
+		__BITFIELD_FIELD(uint64_t xkmemenau:1,
+		/* R/W If set (and SX set), supervisor-level
+		 * loads/stores can use XKPHYS addresses with
+		 * VA<48>==1 */
+		__BITFIELD_FIELD(uint64_t xkioenas:1,
+		/* R/W If set (and UX set), user-level loads/stores
+		 * can use XKPHYS addresses with VA<48>==1 */
+		__BITFIELD_FIELD(uint64_t xkioenau:1,
+		/* R/W If set, all stores act as SYNCW (NOMERGE must
+		 * be set when this is set) RW, reset to 0. */
+		__BITFIELD_FIELD(uint64_t allsyncw:1,
+		/* R/W If set, no stores merge, and all stores reach
+		 * the coherent bus in order. */
+		__BITFIELD_FIELD(uint64_t nomerge:1,
+		/* R/W Selects the bit in the counter used for DID
+		 * time-outs 0 = 231, 1 = 230, 2 = 229, 3 =
+		 * 214. Actual time-out is between 1x and 2x this
+		 * interval. For example, with DIDTTO=3, expiration
+		 * interval is between 16K and 32K. */
+		__BITFIELD_FIELD(uint64_t didtto:2,
+		/* R/W If set, the (mem) CSR clock never turns off. */
+		__BITFIELD_FIELD(uint64_t csrckalwys:1,
+		/* R/W If set, mclk never turns off. */
+		__BITFIELD_FIELD(uint64_t mclkalwys:1,
+		/* R/W Selects the bit in the counter used for write
+		 * buffer flush time-outs (WBFLT+11) is the bit
+		 * position in an internal counter used to determine
+		 * expiration. The write buffer expires between 1x and
+		 * 2x this interval. For example, with WBFLT = 0, a
+		 * write buffer expires between 2K and 4K cycles after
+		 * the write buffer entry is allocated. */
+		__BITFIELD_FIELD(uint64_t wbfltime:3,
+		/* R/W If set, do not put Istream in the L2 cache. */
+		__BITFIELD_FIELD(uint64_t istrnol2:1,
+		/* R/W The write buffer threshold. */
+		__BITFIELD_FIELD(uint64_t wbthresh:4,
+		/* Reserved */
+		__BITFIELD_FIELD(uint64_t reserved2:2,
+		/* R/W If set, CVMSEG is available for loads/stores in
+		 * kernel/debug mode. */
+		__BITFIELD_FIELD(uint64_t cvmsegenak:1,
+		/* R/W If set, CVMSEG is available for loads/stores in
+		 * supervisor mode. */
+		__BITFIELD_FIELD(uint64_t cvmsegenas:1,
+		/* R/W If set, CVMSEG is available for loads/stores in
+		 * user mode. */
+		__BITFIELD_FIELD(uint64_t cvmsegenau:1,
+		/* R/W Size of local memory in cache blocks, 54 (6912
+		 * bytes) is max legal value. */
+		__BITFIELD_FIELD(uint64_t lmemsz:6,
+		;)))))))))))))))))))))))))))))))))
+	} s;
+};
+
+extern void octeon_check_cpu_bist(void);
+
+int octeon_prune_device_tree(void);
+extern const char __dtb_octeon_3xxx_begin;
+extern const char __dtb_octeon_68xx_begin;
+
+/**
+ * Write a 32bit value to the Octeon NPI register space
+ *
+ * @address: Address to write to
+ * @val:     Value to write
+ */
+static inline void octeon_npi_write32(uint64_t address, uint32_t val)
+{
+	cvmx_write64_uint32(address ^ 4, val);
+	cvmx_read64_uint32(address ^ 4);
+}
+
+#ifdef CONFIG_SMP
+void octeon_setup_smp(void);
+#else
+static inline void octeon_setup_smp(void) {}
+#endif
+
+struct irq_domain;
+struct device_node;
+struct irq_data;
+struct irq_chip;
+void octeon_ciu3_mbox_send(int cpu, unsigned int mbox);
+int octeon_irq_ciu3_xlat(struct irq_domain *d,
+			 struct device_node *node,
+			 const u32 *intspec,
+			 unsigned int intsize,
+			 unsigned long *out_hwirq,
+			 unsigned int *out_type);
+void octeon_irq_ciu3_enable(struct irq_data *data);
+void octeon_irq_ciu3_disable(struct irq_data *data);
+void octeon_irq_ciu3_ack(struct irq_data *data);
+void octeon_irq_ciu3_mask(struct irq_data *data);
+void octeon_irq_ciu3_mask_ack(struct irq_data *data);
+int octeon_irq_ciu3_mapx(struct irq_domain *d, unsigned int virq,
+			 irq_hw_number_t hw, struct irq_chip *chip);
+
+/* Octeon multiplier save/restore routines from octeon_switch.S */
+void octeon_mult_save(void);
+void octeon_mult_restore(void);
+void octeon_mult_save_end(void);
+void octeon_mult_restore_end(void);
+void octeon_mult_save3(void);
+void octeon_mult_save3_end(void);
+void octeon_mult_save2(void);
+void octeon_mult_save2_end(void);
+void octeon_mult_restore3(void);
+void octeon_mult_restore3_end(void);
+void octeon_mult_restore2(void);
+void octeon_mult_restore2_end(void);
+
+/**
+ * Read a 32bit value from the Octeon NPI register space
+ *
+ * @address: Address to read
+ * Returns The result
+ */
+static inline uint32_t octeon_npi_read32(uint64_t address)
+{
+	return cvmx_read64_uint32(address ^ 4);
+}
+
+extern struct cvmx_bootinfo *octeon_bootinfo;
+
+extern uint64_t octeon_bootloader_entry_addr;
+
+extern void (*octeon_irq_setup_secondary)(void);
+
+typedef void (*octeon_irq_ip4_handler_t)(void);
+void octeon_irq_set_ip4_handler(octeon_irq_ip4_handler_t);
+
+extern void octeon_fixup_irqs(void);
+
+extern struct semaphore octeon_bootbus_sem;
+
+struct irq_domain *octeon_irq_get_block_domain(int node, uint8_t block);
+
+#endif /* __ASM_OCTEON_OCTEON_H */
diff --git a/arch/mips/include/asm/octeon/pci-octeon.h b/arch/mips/include/asm/octeon/pci-octeon.h
new file mode 100644
index 000000000..2f46f6c6e
--- /dev/null
+++ b/arch/mips/include/asm/octeon/pci-octeon.h
@@ -0,0 +1,67 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2005-2009 Cavium Networks
+ */
+
+#ifndef __PCI_OCTEON_H__
+#define __PCI_OCTEON_H__
+
+#include <linux/pci.h>
+
+/*
+ * The physical memory base mapped by BAR1.  256MB at the end of the
+ * first 4GB.
+ */
+#define CVMX_PCIE_BAR1_PHYS_BASE ((1ull << 32) - (1ull << 28))
+#define CVMX_PCIE_BAR1_PHYS_SIZE (1ull << 28)
+
+/*
+ * The RC base of BAR1.	 gen1 has a 39-bit BAR2, gen2 has 41-bit BAR2,
+ * place BAR1 so it is the same for both.
+ */
+#define CVMX_PCIE_BAR1_RC_BASE (1ull << 41)
+
+/*
+ * pcibios_map_irq() is defined inside pci-octeon.c. All it does is
+ * call the Octeon specific version pointed to by this variable. This
+ * function needs to change for PCI or PCIe based hosts.
+ */
+extern int (*octeon_pcibios_map_irq)(const struct pci_dev *dev,
+				     u8 slot, u8 pin);
+
+/*
+ * For PCI (not PCIe) the BAR2 base address.
+ */
+#define OCTEON_BAR2_PCI_ADDRESS 0x8000000000ull
+
+/*
+ * For PCI (not PCIe) the base of the memory mapped by BAR1
+ */
+extern u64 octeon_bar1_pci_phys;
+
+/*
+ * The following defines are used when octeon_dma_bar_type =
+ * OCTEON_DMA_BAR_TYPE_BIG
+ */
+#define OCTEON_PCI_BAR1_HOLE_BITS 5
+#define OCTEON_PCI_BAR1_HOLE_SIZE (1ul<<(OCTEON_PCI_BAR1_HOLE_BITS+3))
+
+enum octeon_dma_bar_type {
+	OCTEON_DMA_BAR_TYPE_INVALID,
+	OCTEON_DMA_BAR_TYPE_SMALL,
+	OCTEON_DMA_BAR_TYPE_BIG,
+	OCTEON_DMA_BAR_TYPE_PCIE,
+	OCTEON_DMA_BAR_TYPE_PCIE2
+};
+
+/*
+ * This tells the DMA mapping system in dma-octeon.c how to map PCI
+ * DMA addresses.
+ */
+extern enum octeon_dma_bar_type octeon_dma_bar_type;
+
+void octeon_pci_dma_init(void);
+#endif
diff --git a/arch/mips/include/asm/paccess.h b/arch/mips/include/asm/paccess.h
new file mode 100644
index 000000000..af81ab0da
--- /dev/null
+++ b/arch/mips/include/asm/paccess.h
@@ -0,0 +1,114 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1996, 1997, 1998, 1999, 2000 by Ralf Baechle
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ *
+ * Protected memory access.  Used for everything that might take revenge
+ * by sending a DBE error like accessing possibly non-existent memory or
+ * devices.
+ */
+#ifndef _ASM_PACCESS_H
+#define _ASM_PACCESS_H
+
+#include <linux/errno.h>
+
+#ifdef CONFIG_32BIT
+#define __PA_ADDR	".word"
+#endif
+#ifdef CONFIG_64BIT
+#define __PA_ADDR	".dword"
+#endif
+
+extern asmlinkage void handle_ibe(void);
+extern asmlinkage void handle_dbe(void);
+
+#define put_dbe(x, ptr) __put_dbe((x), (ptr), sizeof(*(ptr)))
+#define get_dbe(x, ptr) __get_dbe((x), (ptr), sizeof(*(ptr)))
+
+struct __large_pstruct { unsigned long buf[100]; };
+#define __mp(x) (*(struct __large_pstruct *)(x))
+
+#define __get_dbe(x, ptr, size)						\
+({									\
+	long __gu_err;							\
+	__typeof__(*(ptr)) __gu_val;					\
+	unsigned long __gu_addr;					\
+	__asm__("":"=r" (__gu_val));					\
+	__gu_addr = (unsigned long) (ptr);				\
+	__asm__("":"=r" (__gu_err));					\
+	switch (size) {							\
+	case 1: __get_dbe_asm("lb"); break;				\
+	case 2: __get_dbe_asm("lh"); break;				\
+	case 4: __get_dbe_asm("lw"); break;				\
+	case 8:	 __get_dbe_asm("ld"); break;				\
+	default: __get_dbe_unknown(); break;				\
+	}								\
+	x = (__typeof__(*(ptr))) __gu_val;				\
+	__gu_err;							\
+})
+
+#define __get_dbe_asm(insn)						\
+{									\
+	__asm__ __volatile__(						\
+	"1:\t" insn "\t%1,%2\n\t"					\
+	"move\t%0,$0\n"							\
+	"2:\n\t"							\
+	".insn\n\t"							\
+	".section\t.fixup,\"ax\"\n"					\
+	"3:\tli\t%0,%3\n\t"						\
+	"move\t%1,$0\n\t"						\
+	"j\t2b\n\t"							\
+	".previous\n\t"							\
+	".section\t__dbe_table,\"a\"\n\t"				\
+	__PA_ADDR "\t1b, 3b\n\t"					\
+	".previous"							\
+	:"=r" (__gu_err), "=r" (__gu_val)				\
+	:"o" (__mp(__gu_addr)), "i" (-EFAULT));				\
+}
+
+extern void __get_dbe_unknown(void);
+
+#define __put_dbe(x, ptr, size)						\
+({									\
+	long __pu_err;							\
+	__typeof__(*(ptr)) __pu_val;					\
+	long __pu_addr;							\
+	__pu_val = (x);							\
+	__pu_addr = (long) (ptr);					\
+	__asm__("":"=r" (__pu_err));					\
+	switch (size) {							\
+	case 1: __put_dbe_asm("sb"); break;				\
+	case 2: __put_dbe_asm("sh"); break;				\
+	case 4: __put_dbe_asm("sw"); break;				\
+	case 8: __put_dbe_asm("sd"); break;				\
+	default: __put_dbe_unknown(); break;				\
+	}								\
+	__pu_err;							\
+})
+
+#define __put_dbe_asm(insn)						\
+{									\
+	__asm__ __volatile__(						\
+	"1:\t" insn "\t%1,%2\n\t"					\
+	"move\t%0,$0\n"							\
+	"2:\n\t"							\
+	".insn\n\t"							\
+	".section\t.fixup,\"ax\"\n"					\
+	"3:\tli\t%0,%3\n\t"						\
+	"j\t2b\n\t"							\
+	".previous\n\t"							\
+	".section\t__dbe_table,\"a\"\n\t"				\
+	__PA_ADDR "\t1b, 3b\n\t"					\
+	".previous"							\
+	: "=r" (__pu_err)						\
+	: "r" (__pu_val), "o" (__mp(__pu_addr)), "i" (-EFAULT));	\
+}
+
+extern void __put_dbe_unknown(void);
+
+extern unsigned long search_dbe_table(unsigned long addr);
+
+#endif /* _ASM_PACCESS_H */
diff --git a/arch/mips/include/asm/page.h b/arch/mips/include/asm/page.h
new file mode 100644
index 000000000..96bc798c1
--- /dev/null
+++ b/arch/mips/include/asm/page.h
@@ -0,0 +1,273 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994 - 1999, 2000, 03 Ralf Baechle
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_PAGE_H
+#define _ASM_PAGE_H
+
+#include <spaces.h>
+#include <linux/const.h>
+#include <linux/kernel.h>
+#include <asm/mipsregs.h>
+
+/*
+ * PAGE_SHIFT determines the page size
+ */
+#ifdef CONFIG_PAGE_SIZE_4KB
+#define PAGE_SHIFT	12
+#endif
+#ifdef CONFIG_PAGE_SIZE_8KB
+#define PAGE_SHIFT	13
+#endif
+#ifdef CONFIG_PAGE_SIZE_16KB
+#define PAGE_SHIFT	14
+#endif
+#ifdef CONFIG_PAGE_SIZE_32KB
+#define PAGE_SHIFT	15
+#endif
+#ifdef CONFIG_PAGE_SIZE_64KB
+#define PAGE_SHIFT	16
+#endif
+#define PAGE_SIZE	(_AC(1,UL) << PAGE_SHIFT)
+#define PAGE_MASK	(~((1 << PAGE_SHIFT) - 1))
+
+/*
+ * This is used for calculating the real page sizes
+ * for FTLB or VTLB + FTLB configurations.
+ */
+static inline unsigned int page_size_ftlb(unsigned int mmuextdef)
+{
+	switch (mmuextdef) {
+	case MIPS_CONF4_MMUEXTDEF_FTLBSIZEEXT:
+		if (PAGE_SIZE == (1 << 30))
+			return 5;
+		if (PAGE_SIZE == (1llu << 32))
+			return 6;
+		if (PAGE_SIZE > (256 << 10))
+			return 7; /* reserved */
+		fallthrough;
+	case MIPS_CONF4_MMUEXTDEF_VTLBSIZEEXT:
+		return (PAGE_SHIFT - 10) / 2;
+	default:
+		panic("Invalid FTLB configuration with Conf4_mmuextdef=%d value\n",
+		      mmuextdef >> 14);
+	}
+}
+
+#ifdef CONFIG_MIPS_HUGE_TLB_SUPPORT
+#define HPAGE_SHIFT	(PAGE_SHIFT + PAGE_SHIFT - 3)
+#define HPAGE_SIZE	(_AC(1,UL) << HPAGE_SHIFT)
+#define HPAGE_MASK	(~(HPAGE_SIZE - 1))
+#define HUGETLB_PAGE_ORDER	(HPAGE_SHIFT - PAGE_SHIFT)
+#else /* !CONFIG_MIPS_HUGE_TLB_SUPPORT */
+#define HPAGE_SHIFT	({BUILD_BUG(); 0; })
+#define HPAGE_SIZE	({BUILD_BUG(); 0; })
+#define HPAGE_MASK	({BUILD_BUG(); 0; })
+#define HUGETLB_PAGE_ORDER	({BUILD_BUG(); 0; })
+#endif /* CONFIG_MIPS_HUGE_TLB_SUPPORT */
+
+#include <linux/pfn.h>
+
+extern void build_clear_page(void);
+extern void build_copy_page(void);
+
+/*
+ * It's normally defined only for FLATMEM config but it's
+ * used in our early mem init code for all memory models.
+ * So always define it.
+ */
+#ifdef CONFIG_MIPS_AUTO_PFN_OFFSET
+extern unsigned long ARCH_PFN_OFFSET;
+# define ARCH_PFN_OFFSET	ARCH_PFN_OFFSET
+#else
+# define ARCH_PFN_OFFSET	PFN_UP(PHYS_OFFSET)
+#endif
+
+extern void clear_page(void * page);
+extern void copy_page(void * to, void * from);
+
+extern unsigned long shm_align_mask;
+
+static inline unsigned long pages_do_alias(unsigned long addr1,
+	unsigned long addr2)
+{
+	return (addr1 ^ addr2) & shm_align_mask;
+}
+
+struct page;
+
+static inline void clear_user_page(void *addr, unsigned long vaddr,
+	struct page *page)
+{
+	extern void (*flush_data_cache_page)(unsigned long addr);
+
+	clear_page(addr);
+	if (pages_do_alias((unsigned long) addr, vaddr & PAGE_MASK))
+		flush_data_cache_page((unsigned long)addr);
+}
+
+struct vm_area_struct;
+extern void copy_user_highpage(struct page *to, struct page *from,
+	unsigned long vaddr, struct vm_area_struct *vma);
+
+#define __HAVE_ARCH_COPY_USER_HIGHPAGE
+
+/*
+ * These are used to make use of C type-checking..
+ */
+#ifdef CONFIG_PHYS_ADDR_T_64BIT
+  #ifdef CONFIG_CPU_MIPS32
+    typedef struct { unsigned long pte_low, pte_high; } pte_t;
+    #define pte_val(x)	  ((x).pte_low | ((unsigned long long)(x).pte_high << 32))
+    #define __pte(x)	  ({ pte_t __pte = {(x), ((unsigned long long)(x)) >> 32}; __pte; })
+  #else
+     typedef struct { unsigned long long pte; } pte_t;
+     #define pte_val(x) ((x).pte)
+     #define __pte(x)	((pte_t) { (x) } )
+  #endif
+#else
+typedef struct { unsigned long pte; } pte_t;
+#define pte_val(x)	((x).pte)
+#define __pte(x)	((pte_t) { (x) } )
+#endif
+typedef struct page *pgtable_t;
+
+/*
+ * Right now we don't support 4-level pagetables, so all pud-related
+ * definitions come from <asm-generic/pgtable-nopud.h>.
+ */
+
+/*
+ * Finall the top of the hierarchy, the pgd
+ */
+typedef struct { unsigned long pgd; } pgd_t;
+#define pgd_val(x)	((x).pgd)
+#define __pgd(x)	((pgd_t) { (x) } )
+
+/*
+ * Manipulate page protection bits
+ */
+typedef struct { unsigned long pgprot; } pgprot_t;
+#define pgprot_val(x)	((x).pgprot)
+#define __pgprot(x)	((pgprot_t) { (x) } )
+#define pte_pgprot(x)	__pgprot(pte_val(x) & ~_PFN_MASK)
+
+/*
+ * On R4000-style MMUs where a TLB entry is mapping a adjacent even / odd
+ * pair of pages we only have a single global bit per pair of pages.  When
+ * writing to the TLB make sure we always have the bit set for both pages
+ * or none.  This macro is used to access the `buddy' of the pte we're just
+ * working on.
+ */
+#define ptep_buddy(x)	((pte_t *)((unsigned long)(x) ^ sizeof(pte_t)))
+
+/*
+ * __pa()/__va() should be used only during mem init.
+ */
+static inline unsigned long ___pa(unsigned long x)
+{
+	if (IS_ENABLED(CONFIG_64BIT)) {
+		/*
+		 * For MIPS64 the virtual address may either be in one of
+		 * the compatibility segements ckseg0 or ckseg1, or it may
+		 * be in xkphys.
+		 */
+		return x < CKSEG0 ? XPHYSADDR(x) : CPHYSADDR(x);
+	}
+
+	if (!IS_ENABLED(CONFIG_EVA)) {
+		/*
+		 * We're using the standard MIPS32 legacy memory map, ie.
+		 * the address x is going to be in kseg0 or kseg1. We can
+		 * handle either case by masking out the desired bits using
+		 * CPHYSADDR.
+		 */
+		return CPHYSADDR(x);
+	}
+
+	/*
+	 * EVA is in use so the memory map could be anything, making it not
+	 * safe to just mask out bits.
+	 */
+	return x - PAGE_OFFSET + PHYS_OFFSET;
+}
+#define __pa(x)		___pa((unsigned long)(x))
+#define __va(x)		((void *)((unsigned long)(x) + PAGE_OFFSET - PHYS_OFFSET))
+#include <asm/io.h>
+
+/*
+ * RELOC_HIDE was originally added by 6007b903dfe5f1d13e0c711ac2894bdd4a61b1ad
+ * (lmo) rsp. 8431fd094d625b94d364fe393076ccef88e6ce18 (kernel.org).  The
+ * discussion can be found in
+ * https://lore.kernel.org/lkml/a2ebde260608230500o3407b108hc03debb9da6e62c@mail.gmail.com
+ *
+ * It is unclear if the misscompilations mentioned in
+ * https://lore.kernel.org/lkml/1281303490-390-1-git-send-email-namhyung@gmail.com
+ * also affect MIPS so we keep this one until GCC 3.x has been retired
+ * before we can apply https://patchwork.linux-mips.org/patch/1541/
+ */
+#define __pa_symbol_nodebug(x)	__pa(RELOC_HIDE((unsigned long)(x), 0))
+
+#ifdef CONFIG_DEBUG_VIRTUAL
+extern phys_addr_t __phys_addr_symbol(unsigned long x);
+#else
+#define __phys_addr_symbol(x)	__pa_symbol_nodebug(x)
+#endif
+
+#ifndef __pa_symbol
+#define __pa_symbol(x)		__phys_addr_symbol((unsigned long)(x))
+#endif
+
+#define pfn_to_kaddr(pfn)	__va((pfn) << PAGE_SHIFT)
+
+#ifdef CONFIG_FLATMEM
+
+static inline int pfn_valid(unsigned long pfn)
+{
+	/* avoid <linux/mm.h> include hell */
+	extern unsigned long max_mapnr;
+	unsigned long pfn_offset = ARCH_PFN_OFFSET;
+
+	return pfn >= pfn_offset && pfn < max_mapnr;
+}
+
+#elif defined(CONFIG_SPARSEMEM)
+
+/* pfn_valid is defined in linux/mmzone.h */
+
+#elif defined(CONFIG_NUMA)
+
+#define pfn_valid(pfn)							\
+({									\
+	unsigned long __pfn = (pfn);					\
+	int __n = pfn_to_nid(__pfn);					\
+	((__n >= 0) ? (__pfn < NODE_DATA(__n)->node_start_pfn +		\
+			       NODE_DATA(__n)->node_spanned_pages)	\
+		    : 0);						\
+})
+
+#endif
+
+#define virt_to_pfn(kaddr)   	PFN_DOWN(virt_to_phys((void *)(kaddr)))
+#define virt_to_page(kaddr)	pfn_to_page(virt_to_pfn(kaddr))
+
+extern bool __virt_addr_valid(const volatile void *kaddr);
+#define virt_addr_valid(kaddr)						\
+	__virt_addr_valid((const volatile void *) (kaddr))
+
+#define VM_DATA_DEFAULT_FLAGS	VM_DATA_FLAGS_TSK_EXEC
+
+extern unsigned long __kaslr_offset;
+static inline unsigned long kaslr_offset(void)
+{
+	return __kaslr_offset;
+}
+
+#include <asm-generic/memory_model.h>
+#include <asm-generic/getorder.h>
+
+#endif /* _ASM_PAGE_H */
diff --git a/arch/mips/include/asm/pci.h b/arch/mips/include/asm/pci.h
new file mode 100644
index 000000000..3fd6e22c1
--- /dev/null
+++ b/arch/mips/include/asm/pci.h
@@ -0,0 +1,142 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#ifndef _ASM_PCI_H
+#define _ASM_PCI_H
+
+#include <linux/mm.h>
+
+#ifdef __KERNEL__
+
+/*
+ * This file essentially defines the interface between board
+ * specific PCI code and MIPS common PCI code.	Should potentially put
+ * into include/asm/pci.h file.
+ */
+
+#include <linux/ioport.h>
+#include <linux/list.h>
+#include <linux/of.h>
+
+#ifdef CONFIG_PCI_DRIVERS_LEGACY
+
+/*
+ * Each pci channel is a top-level PCI bus seem by CPU.	 A machine  with
+ * multiple PCI channels may have multiple PCI host controllers or a
+ * single controller supporting multiple channels.
+ */
+struct pci_controller {
+	struct list_head list;
+	struct pci_bus *bus;
+	struct device_node *of_node;
+
+	struct pci_ops *pci_ops;
+	struct resource *mem_resource;
+	unsigned long mem_offset;
+	struct resource *io_resource;
+	unsigned long io_offset;
+	unsigned long io_map_base;
+
+#ifndef CONFIG_PCI_DOMAINS_GENERIC
+	unsigned int index;
+	/* For compatibility with current (as of July 2003) pciutils
+	   and XFree86. Eventually will be removed. */
+	unsigned int need_domain_info;
+#endif
+
+	/* Optional access methods for reading/writing the bus number
+	   of the PCI controller */
+	int (*get_busno)(void);
+	void (*set_busno)(int busno);
+};
+
+/*
+ * Used by boards to register their PCI busses before the actual scanning.
+ */
+extern void register_pci_controller(struct pci_controller *hose);
+
+/*
+ * board supplied pci irq fixup routine
+ */
+extern int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin);
+
+/* Do platform specific device initialization at pci_enable_device() time */
+extern int pcibios_plat_dev_init(struct pci_dev *dev);
+
+extern char * (*pcibios_plat_setup)(char *str);
+
+#ifdef CONFIG_OF
+/* this function parses memory ranges from a device node */
+extern void pci_load_of_ranges(struct pci_controller *hose,
+			       struct device_node *node);
+#else
+static inline void pci_load_of_ranges(struct pci_controller *hose,
+				      struct device_node *node) {}
+#endif
+
+#ifdef CONFIG_PCI_DOMAINS_GENERIC
+static inline void set_pci_need_domain_info(struct pci_controller *hose,
+					    int need_domain_info)
+{
+	/* nothing to do */
+}
+#elif defined(CONFIG_PCI_DOMAINS)
+static inline void set_pci_need_domain_info(struct pci_controller *hose,
+					    int need_domain_info)
+{
+	hose->need_domain_info = need_domain_info;
+}
+#endif /* CONFIG_PCI_DOMAINS */
+
+#endif
+
+/* Can be used to override the logic in pci_scan_bus for skipping
+   already-configured bus numbers - to be used for buggy BIOSes
+   or architectures with incomplete PCI setup by the loader */
+static inline unsigned int pcibios_assign_all_busses(void)
+{
+	return 1;
+}
+
+extern unsigned long PCIBIOS_MIN_IO;
+extern unsigned long PCIBIOS_MIN_MEM;
+
+#define PCIBIOS_MIN_CARDBUS_IO	0x4000
+
+#define HAVE_PCI_MMAP
+#define ARCH_GENERIC_PCI_MMAP_RESOURCE
+
+/*
+ * Dynamic DMA mapping stuff.
+ * MIPS has everything mapped statically.
+ */
+
+#include <linux/types.h>
+#include <linux/slab.h>
+#include <linux/scatterlist.h>
+#include <linux/string.h>
+#include <asm/io.h>
+
+#ifdef CONFIG_PCI_DOMAINS_GENERIC
+static inline int pci_proc_domain(struct pci_bus *bus)
+{
+	return pci_domain_nr(bus);
+}
+#elif defined(CONFIG_PCI_DOMAINS)
+#define pci_domain_nr(bus) ((struct pci_controller *)(bus)->sysdata)->index
+
+static inline int pci_proc_domain(struct pci_bus *bus)
+{
+	struct pci_controller *hose = bus->sysdata;
+	return hose->need_domain_info;
+}
+#endif /* CONFIG_PCI_DOMAINS */
+
+#endif /* __KERNEL__ */
+
+/* Do platform specific device initialization at pci_enable_device() time */
+extern int pcibios_plat_dev_init(struct pci_dev *dev);
+
+#endif /* _ASM_PCI_H */
diff --git a/arch/mips/include/asm/pci/bridge.h b/arch/mips/include/asm/pci/bridge.h
new file mode 100644
index 000000000..9c476a040
--- /dev/null
+++ b/arch/mips/include/asm/pci/bridge.h
@@ -0,0 +1,825 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * bridge.h - bridge chip header file, derived from IRIX <sys/PCI/bridge.h>,
+ * revision 1.76.
+ *
+ * Copyright (C) 1996, 1999 Silcon Graphics, Inc.
+ * Copyright (C) 1999 Ralf Baechle (ralf@gnu.org)
+ */
+#ifndef _ASM_PCI_BRIDGE_H
+#define _ASM_PCI_BRIDGE_H
+
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <asm/xtalk/xwidget.h>		/* generic widget header */
+#include <asm/sn/types.h>
+
+/* I/O page size */
+
+#define IOPFNSHIFT		12	/* 4K per mapped page */
+
+#define IOPGSIZE		(1 << IOPFNSHIFT)
+#define IOPG(x)			((x) >> IOPFNSHIFT)
+#define IOPGOFF(x)		((x) & (IOPGSIZE-1))
+
+/* Bridge RAM sizes */
+
+#define BRIDGE_ATE_RAM_SIZE	0x00000400	/* 1kB ATE RAM */
+
+#define BRIDGE_CONFIG_BASE	0x20000
+#define BRIDGE_CONFIG1_BASE	0x28000
+#define BRIDGE_CONFIG_END	0x30000
+#define BRIDGE_CONFIG_SLOT_SIZE 0x1000
+
+#define BRIDGE_SSRAM_512K	0x00080000	/* 512kB */
+#define BRIDGE_SSRAM_128K	0x00020000	/* 128kB */
+#define BRIDGE_SSRAM_64K	0x00010000	/* 64kB */
+#define BRIDGE_SSRAM_0K		0x00000000	/* 0kB */
+
+/* ========================================================================
+ *    Bridge address map
+ */
+
+#ifndef __ASSEMBLY__
+
+#define ATE_V		0x01
+#define ATE_CO		0x02
+#define ATE_PREC	0x04
+#define ATE_PREF	0x08
+#define ATE_BAR		0x10
+
+#define ATE_PFNSHIFT		12
+#define ATE_TIDSHIFT		8
+#define ATE_RMFSHIFT		48
+
+#define mkate(xaddr, xid, attr) (((xaddr) & 0x0000fffffffff000ULL) | \
+				 ((xid)<<ATE_TIDSHIFT) | \
+				 (attr))
+
+#define BRIDGE_INTERNAL_ATES	128
+
+/*
+ * It is generally preferred that hardware registers on the bridge
+ * are located from C code via this structure.
+ *
+ * Generated from Bridge spec dated 04oct95
+ */
+
+struct bridge_regs {
+	/* Local Registers			       0x000000-0x00FFFF */
+
+	/* standard widget configuration	       0x000000-0x000057 */
+	widget_cfg_t	    b_widget;			/* 0x000000 */
+
+	/* helper fieldnames for accessing bridge widget */
+
+#define b_wid_id			b_widget.w_id
+#define b_wid_stat			b_widget.w_status
+#define b_wid_err_upper			b_widget.w_err_upper_addr
+#define b_wid_err_lower			b_widget.w_err_lower_addr
+#define b_wid_control			b_widget.w_control
+#define b_wid_req_timeout		b_widget.w_req_timeout
+#define b_wid_int_upper			b_widget.w_intdest_upper_addr
+#define b_wid_int_lower			b_widget.w_intdest_lower_addr
+#define b_wid_err_cmdword		b_widget.w_err_cmd_word
+#define b_wid_llp			b_widget.w_llp_cfg
+#define b_wid_tflush			b_widget.w_tflush
+
+	/* bridge-specific widget configuration 0x000058-0x00007F */
+	u32	_pad_000058;
+	u32	b_wid_aux_err;		/* 0x00005C */
+	u32	_pad_000060;
+	u32	b_wid_resp_upper;		/* 0x000064 */
+	u32	_pad_000068;
+	u32	b_wid_resp_lower;		/* 0x00006C */
+	u32	_pad_000070;
+	u32	 b_wid_tst_pin_ctrl;		/* 0x000074 */
+	u32	_pad_000078[2];
+
+	/* PMU & Map 0x000080-0x00008F */
+	u32	_pad_000080;
+	u32	b_dir_map;			/* 0x000084 */
+	u32	_pad_000088[2];
+
+	/* SSRAM 0x000090-0x00009F */
+	u32	_pad_000090;
+	u32	b_ram_perr;			/* 0x000094 */
+	u32	_pad_000098[2];
+
+	/* Arbitration 0x0000A0-0x0000AF */
+	u32	_pad_0000A0;
+	u32	b_arb;				/* 0x0000A4 */
+	u32	_pad_0000A8[2];
+
+	/* Number In A Can 0x0000B0-0x0000BF */
+	u32	_pad_0000B0;
+	u32	b_nic;				/* 0x0000B4 */
+	u32	_pad_0000B8[2];
+
+	/* PCI/GIO 0x0000C0-0x0000FF */
+	u32	_pad_0000C0;
+	u32	b_bus_timeout;			/* 0x0000C4 */
+#define b_pci_bus_timeout b_bus_timeout
+
+	u32	_pad_0000C8;
+	u32	b_pci_cfg;			/* 0x0000CC */
+	u32	_pad_0000D0;
+	u32	b_pci_err_upper;		/* 0x0000D4 */
+	u32	_pad_0000D8;
+	u32	b_pci_err_lower;		/* 0x0000DC */
+	u32	_pad_0000E0[8];
+#define b_gio_err_lower b_pci_err_lower
+#define b_gio_err_upper b_pci_err_upper
+
+	/* Interrupt 0x000100-0x0001FF */
+	u32	_pad_000100;
+	u32	b_int_status;			/* 0x000104 */
+	u32	_pad_000108;
+	u32	b_int_enable;			/* 0x00010C */
+	u32	_pad_000110;
+	u32	b_int_rst_stat;			/* 0x000114 */
+	u32	_pad_000118;
+	u32	b_int_mode;			/* 0x00011C */
+	u32	_pad_000120;
+	u32	b_int_device;			/* 0x000124 */
+	u32	_pad_000128;
+	u32	b_int_host_err;			/* 0x00012C */
+
+	struct {
+		u32	__pad;			/* 0x0001{30,,,68} */
+		u32	addr;			/* 0x0001{34,,,6C} */
+	} b_int_addr[8];				/* 0x000130 */
+
+	u32	_pad_000170[36];
+
+	/* Device 0x000200-0x0003FF */
+	struct {
+		u32	__pad;			/* 0x0002{00,,,38} */
+		u32	reg;			/* 0x0002{04,,,3C} */
+	} b_device[8];					/* 0x000200 */
+
+	struct {
+		u32	__pad;			/* 0x0002{40,,,78} */
+		u32	reg;			/* 0x0002{44,,,7C} */
+	} b_wr_req_buf[8];				/* 0x000240 */
+
+	struct {
+		u32	__pad;			/* 0x0002{80,,,88} */
+		u32	reg;			/* 0x0002{84,,,8C} */
+	} b_rrb_map[2];					/* 0x000280 */
+#define b_even_resp	b_rrb_map[0].reg		/* 0x000284 */
+#define b_odd_resp	b_rrb_map[1].reg		/* 0x00028C */
+
+	u32	_pad_000290;
+	u32	b_resp_status;			/* 0x000294 */
+	u32	_pad_000298;
+	u32	b_resp_clear;			/* 0x00029C */
+
+	u32	_pad_0002A0[24];
+
+	char		_pad_000300[0x10000 - 0x000300];
+
+	/* Internal Address Translation Entry RAM 0x010000-0x0103FF */
+	union {
+		u64	wr;			/* write-only */
+		struct {
+			u32	_p_pad;
+			u32	rd;		/* read-only */
+		}			hi;
+	}			    b_int_ate_ram[128];
+
+	char	_pad_010400[0x11000 - 0x010400];
+
+	/* Internal Address Translation Entry RAM LOW 0x011000-0x0113FF */
+	struct {
+		u32	_p_pad;
+		u32	rd;		/* read-only */
+	} b_int_ate_ram_lo[128];
+
+	char	_pad_011400[0x20000 - 0x011400];
+
+	/* PCI Device Configuration Spaces 0x020000-0x027FFF */
+	union {				/* make all access sizes available. */
+		u8	c[0x1000 / 1];
+		u16	s[0x1000 / 2];
+		u32	l[0x1000 / 4];
+		u64	d[0x1000 / 8];
+		union {
+			u8	c[0x100 / 1];
+			u16	s[0x100 / 2];
+			u32	l[0x100 / 4];
+			u64	d[0x100 / 8];
+		} f[8];
+	} b_type0_cfg_dev[8];					/* 0x020000 */
+
+	/* PCI Type 1 Configuration Space 0x028000-0x028FFF */
+	union {				/* make all access sizes available. */
+		u8	c[0x1000 / 1];
+		u16	s[0x1000 / 2];
+		u32	l[0x1000 / 4];
+		u64	d[0x1000 / 8];
+	} b_type1_cfg;					/* 0x028000-0x029000 */
+
+	char	_pad_029000[0x007000];			/* 0x029000-0x030000 */
+
+	/* PCI Interrupt Acknowledge Cycle 0x030000 */
+	union {
+		u8	c[8 / 1];
+		u16	s[8 / 2];
+		u32	l[8 / 4];
+		u64	d[8 / 8];
+	} b_pci_iack;						/* 0x030000 */
+
+	u8	_pad_030007[0x04fff8];			/* 0x030008-0x07FFFF */
+
+	/* External Address Translation Entry RAM 0x080000-0x0FFFFF */
+	u64	b_ext_ate_ram[0x10000];
+
+	/* Reserved 0x100000-0x1FFFFF */
+	char	_pad_100000[0x200000-0x100000];
+
+	/* PCI/GIO Device Spaces 0x200000-0xBFFFFF */
+	union {				/* make all access sizes available. */
+		u8	c[0x100000 / 1];
+		u16	s[0x100000 / 2];
+		u32	l[0x100000 / 4];
+		u64	d[0x100000 / 8];
+	} b_devio_raw[10];				/* 0x200000 */
+
+	/* b_devio macro is a bit strange; it reflects the
+	 * fact that the Bridge ASIC provides 2M for the
+	 * first two DevIO windows and 1M for the other six.
+	 */
+#define b_devio(n)	b_devio_raw[((n)<2)?(n*2):(n+2)]
+
+	/* External Flash Proms 1,0 0xC00000-0xFFFFFF */
+	union {		/* make all access sizes available. */
+		u8	c[0x400000 / 1];	/* read-only */
+		u16	s[0x400000 / 2];	/* read-write */
+		u32	l[0x400000 / 4];	/* read-only */
+		u64	d[0x400000 / 8];	/* read-only */
+	} b_external_flash;			/* 0xC00000 */
+};
+
+/*
+ * Field formats for Error Command Word and Auxiliary Error Command Word
+ * of bridge.
+ */
+struct bridge_err_cmdword {
+	union {
+		u32		cmd_word;
+		struct {
+			u32	didn:4,		/* Destination ID  */
+				sidn:4,		/* Source ID	   */
+				pactyp:4,	/* Packet type	   */
+				tnum:5,		/* Trans Number	   */
+				coh:1,		/* Coh Transaction */
+				ds:2,		/* Data size	   */
+				gbr:1,		/* GBR enable	   */
+				vbpm:1,		/* VBPM message	   */
+				error:1,	/* Error occurred  */
+				barr:1,		/* Barrier op	   */
+				rsvd:8;
+		} berr_st;
+	} berr_un;
+};
+
+#define berr_field	berr_un.berr_st
+#endif /* !__ASSEMBLY__ */
+
+/*
+ * The values of these macros can and should be crosschecked
+ * regularly against the offsets of the like-named fields
+ * within the bridge_regs structure above.
+ */
+
+/* Byte offset macros for Bridge internal registers */
+
+#define BRIDGE_WID_ID		WIDGET_ID
+#define BRIDGE_WID_STAT		WIDGET_STATUS
+#define BRIDGE_WID_ERR_UPPER	WIDGET_ERR_UPPER_ADDR
+#define BRIDGE_WID_ERR_LOWER	WIDGET_ERR_LOWER_ADDR
+#define BRIDGE_WID_CONTROL	WIDGET_CONTROL
+#define BRIDGE_WID_REQ_TIMEOUT	WIDGET_REQ_TIMEOUT
+#define BRIDGE_WID_INT_UPPER	WIDGET_INTDEST_UPPER_ADDR
+#define BRIDGE_WID_INT_LOWER	WIDGET_INTDEST_LOWER_ADDR
+#define BRIDGE_WID_ERR_CMDWORD	WIDGET_ERR_CMD_WORD
+#define BRIDGE_WID_LLP		WIDGET_LLP_CFG
+#define BRIDGE_WID_TFLUSH	WIDGET_TFLUSH
+
+#define BRIDGE_WID_AUX_ERR	0x00005C	/* Aux Error Command Word */
+#define BRIDGE_WID_RESP_UPPER	0x000064	/* Response Buf Upper Addr */
+#define BRIDGE_WID_RESP_LOWER	0x00006C	/* Response Buf Lower Addr */
+#define BRIDGE_WID_TST_PIN_CTRL 0x000074	/* Test pin control */
+
+#define BRIDGE_DIR_MAP		0x000084	/* Direct Map reg */
+
+#define BRIDGE_RAM_PERR		0x000094	/* SSRAM Parity Error */
+
+#define BRIDGE_ARB		0x0000A4	/* Arbitration Priority reg */
+
+#define BRIDGE_NIC		0x0000B4	/* Number In A Can */
+
+#define BRIDGE_BUS_TIMEOUT	0x0000C4	/* Bus Timeout Register */
+#define BRIDGE_PCI_BUS_TIMEOUT	BRIDGE_BUS_TIMEOUT
+#define BRIDGE_PCI_CFG		0x0000CC	/* PCI Type 1 Config reg */
+#define BRIDGE_PCI_ERR_UPPER	0x0000D4	/* PCI error Upper Addr */
+#define BRIDGE_PCI_ERR_LOWER	0x0000DC	/* PCI error Lower Addr */
+
+#define BRIDGE_INT_STATUS	0x000104	/* Interrupt Status */
+#define BRIDGE_INT_ENABLE	0x00010C	/* Interrupt Enables */
+#define BRIDGE_INT_RST_STAT	0x000114	/* Reset Intr Status */
+#define BRIDGE_INT_MODE		0x00011C	/* Interrupt Mode */
+#define BRIDGE_INT_DEVICE	0x000124	/* Interrupt Device */
+#define BRIDGE_INT_HOST_ERR	0x00012C	/* Host Error Field */
+
+#define BRIDGE_INT_ADDR0	0x000134	/* Host Address Reg */
+#define BRIDGE_INT_ADDR_OFF	0x000008	/* Host Addr offset (1..7) */
+#define BRIDGE_INT_ADDR(x)	(BRIDGE_INT_ADDR0+(x)*BRIDGE_INT_ADDR_OFF)
+
+#define BRIDGE_DEVICE0		0x000204	/* Device 0 */
+#define BRIDGE_DEVICE_OFF	0x000008	/* Device offset (1..7) */
+#define BRIDGE_DEVICE(x)	(BRIDGE_DEVICE0+(x)*BRIDGE_DEVICE_OFF)
+
+#define BRIDGE_WR_REQ_BUF0	0x000244	/* Write Request Buffer 0 */
+#define BRIDGE_WR_REQ_BUF_OFF	0x000008	/* Buffer Offset (1..7) */
+#define BRIDGE_WR_REQ_BUF(x)	(BRIDGE_WR_REQ_BUF0+(x)*BRIDGE_WR_REQ_BUF_OFF)
+
+#define BRIDGE_EVEN_RESP	0x000284	/* Even Device Response Buf */
+#define BRIDGE_ODD_RESP		0x00028C	/* Odd Device Response Buf */
+
+#define BRIDGE_RESP_STATUS	0x000294	/* Read Response Status reg */
+#define BRIDGE_RESP_CLEAR	0x00029C	/* Read Response Clear reg */
+
+/* Byte offset macros for Bridge I/O space */
+
+#define BRIDGE_ATE_RAM		0x00010000	/* Internal Addr Xlat Ram */
+
+#define BRIDGE_TYPE0_CFG_DEV0	0x00020000	/* Type 0 Cfg, Device 0 */
+#define BRIDGE_TYPE0_CFG_SLOT_OFF	0x00001000	/* Type 0 Cfg Slot Offset (1..7) */
+#define BRIDGE_TYPE0_CFG_FUNC_OFF	0x00000100	/* Type 0 Cfg Func Offset (1..7) */
+#define BRIDGE_TYPE0_CFG_DEV(s)		(BRIDGE_TYPE0_CFG_DEV0+\
+					 (s)*BRIDGE_TYPE0_CFG_SLOT_OFF)
+#define BRIDGE_TYPE0_CFG_DEVF(s, f)	(BRIDGE_TYPE0_CFG_DEV0+\
+					 (s)*BRIDGE_TYPE0_CFG_SLOT_OFF+\
+					 (f)*BRIDGE_TYPE0_CFG_FUNC_OFF)
+
+#define BRIDGE_TYPE1_CFG	0x00028000	/* Type 1 Cfg space */
+
+#define BRIDGE_PCI_IACK		0x00030000	/* PCI Interrupt Ack */
+#define BRIDGE_EXT_SSRAM	0x00080000	/* Extern SSRAM (ATE) */
+
+/* Byte offset macros for Bridge device IO spaces */
+
+#define BRIDGE_DEV_CNT		8	/* Up to 8 devices per bridge */
+#define BRIDGE_DEVIO0		0x00200000	/* Device IO 0 Addr */
+#define BRIDGE_DEVIO1		0x00400000	/* Device IO 1 Addr */
+#define BRIDGE_DEVIO2		0x00600000	/* Device IO 2 Addr */
+#define BRIDGE_DEVIO_OFF	0x00100000	/* Device IO Offset (3..7) */
+
+#define BRIDGE_DEVIO_2MB	0x00200000	/* Device IO Offset (0..1) */
+#define BRIDGE_DEVIO_1MB	0x00100000	/* Device IO Offset (2..7) */
+
+#define BRIDGE_DEVIO(x)		((x)<=1 ? BRIDGE_DEVIO0+(x)*BRIDGE_DEVIO_2MB : BRIDGE_DEVIO2+((x)-2)*BRIDGE_DEVIO_1MB)
+
+#define BRIDGE_EXTERNAL_FLASH	0x00C00000	/* External Flash PROMS */
+
+/* ========================================================================
+ *    Bridge register bit field definitions
+ */
+
+/* Widget part number of bridge */
+#define BRIDGE_WIDGET_PART_NUM		0xc002
+#define XBRIDGE_WIDGET_PART_NUM		0xd002
+
+/* Manufacturer of bridge */
+#define BRIDGE_WIDGET_MFGR_NUM		0x036
+#define XBRIDGE_WIDGET_MFGR_NUM		0x024
+
+/* Revision numbers for known Bridge revisions */
+#define BRIDGE_REV_A			0x1
+#define BRIDGE_REV_B			0x2
+#define BRIDGE_REV_C			0x3
+#define BRIDGE_REV_D			0x4
+
+/* Bridge widget status register bits definition */
+
+#define BRIDGE_STAT_LLP_REC_CNT		(0xFFu << 24)
+#define BRIDGE_STAT_LLP_TX_CNT		(0xFF << 16)
+#define BRIDGE_STAT_FLASH_SELECT	(0x1 << 6)
+#define BRIDGE_STAT_PCI_GIO_N		(0x1 << 5)
+#define BRIDGE_STAT_PENDING		(0x1F << 0)
+
+/* Bridge widget control register bits definition */
+#define BRIDGE_CTRL_FLASH_WR_EN		(0x1ul << 31)
+#define BRIDGE_CTRL_EN_CLK50		(0x1 << 30)
+#define BRIDGE_CTRL_EN_CLK40		(0x1 << 29)
+#define BRIDGE_CTRL_EN_CLK33		(0x1 << 28)
+#define BRIDGE_CTRL_RST(n)		((n) << 24)
+#define BRIDGE_CTRL_RST_MASK		(BRIDGE_CTRL_RST(0xF))
+#define BRIDGE_CTRL_RST_PIN(x)		(BRIDGE_CTRL_RST(0x1 << (x)))
+#define BRIDGE_CTRL_IO_SWAP		(0x1 << 23)
+#define BRIDGE_CTRL_MEM_SWAP		(0x1 << 22)
+#define BRIDGE_CTRL_PAGE_SIZE		(0x1 << 21)
+#define BRIDGE_CTRL_SS_PAR_BAD		(0x1 << 20)
+#define BRIDGE_CTRL_SS_PAR_EN		(0x1 << 19)
+#define BRIDGE_CTRL_SSRAM_SIZE(n)	((n) << 17)
+#define BRIDGE_CTRL_SSRAM_SIZE_MASK	(BRIDGE_CTRL_SSRAM_SIZE(0x3))
+#define BRIDGE_CTRL_SSRAM_512K		(BRIDGE_CTRL_SSRAM_SIZE(0x3))
+#define BRIDGE_CTRL_SSRAM_128K		(BRIDGE_CTRL_SSRAM_SIZE(0x2))
+#define BRIDGE_CTRL_SSRAM_64K		(BRIDGE_CTRL_SSRAM_SIZE(0x1))
+#define BRIDGE_CTRL_SSRAM_1K		(BRIDGE_CTRL_SSRAM_SIZE(0x0))
+#define BRIDGE_CTRL_F_BAD_PKT		(0x1 << 16)
+#define BRIDGE_CTRL_LLP_XBAR_CRD(n)	((n) << 12)
+#define BRIDGE_CTRL_LLP_XBAR_CRD_MASK	(BRIDGE_CTRL_LLP_XBAR_CRD(0xf))
+#define BRIDGE_CTRL_CLR_RLLP_CNT	(0x1 << 11)
+#define BRIDGE_CTRL_CLR_TLLP_CNT	(0x1 << 10)
+#define BRIDGE_CTRL_SYS_END		(0x1 << 9)
+#define BRIDGE_CTRL_MAX_TRANS(n)	((n) << 4)
+#define BRIDGE_CTRL_MAX_TRANS_MASK	(BRIDGE_CTRL_MAX_TRANS(0x1f))
+#define BRIDGE_CTRL_WIDGET_ID(n)	((n) << 0)
+#define BRIDGE_CTRL_WIDGET_ID_MASK	(BRIDGE_CTRL_WIDGET_ID(0xf))
+
+/* Bridge Response buffer Error Upper Register bit fields definition */
+#define BRIDGE_RESP_ERRUPPR_DEVNUM_SHFT (20)
+#define BRIDGE_RESP_ERRUPPR_DEVNUM_MASK (0x7 << BRIDGE_RESP_ERRUPPR_DEVNUM_SHFT)
+#define BRIDGE_RESP_ERRUPPR_BUFNUM_SHFT (16)
+#define BRIDGE_RESP_ERRUPPR_BUFNUM_MASK (0xF << BRIDGE_RESP_ERRUPPR_BUFNUM_SHFT)
+#define BRIDGE_RESP_ERRRUPPR_BUFMASK	(0xFFFF)
+
+#define BRIDGE_RESP_ERRUPPR_BUFNUM(x)	\
+			(((x) & BRIDGE_RESP_ERRUPPR_BUFNUM_MASK) >> \
+				BRIDGE_RESP_ERRUPPR_BUFNUM_SHFT)
+
+#define BRIDGE_RESP_ERRUPPR_DEVICE(x)	\
+			(((x) &	 BRIDGE_RESP_ERRUPPR_DEVNUM_MASK) >> \
+				 BRIDGE_RESP_ERRUPPR_DEVNUM_SHFT)
+
+/* Bridge direct mapping register bits definition */
+#define BRIDGE_DIRMAP_W_ID_SHFT		20
+#define BRIDGE_DIRMAP_W_ID		(0xf << BRIDGE_DIRMAP_W_ID_SHFT)
+#define BRIDGE_DIRMAP_RMF_64		(0x1 << 18)
+#define BRIDGE_DIRMAP_ADD512		(0x1 << 17)
+#define BRIDGE_DIRMAP_OFF		(0x1ffff << 0)
+#define BRIDGE_DIRMAP_OFF_ADDRSHFT	(31)	/* lsbit of DIRMAP_OFF is xtalk address bit 31 */
+
+/* Bridge Arbitration register bits definition */
+#define BRIDGE_ARB_REQ_WAIT_TICK(x)	((x) << 16)
+#define BRIDGE_ARB_REQ_WAIT_TICK_MASK	BRIDGE_ARB_REQ_WAIT_TICK(0x3)
+#define BRIDGE_ARB_REQ_WAIT_EN(x)	((x) << 8)
+#define BRIDGE_ARB_REQ_WAIT_EN_MASK	BRIDGE_ARB_REQ_WAIT_EN(0xff)
+#define BRIDGE_ARB_FREEZE_GNT		(1 << 6)
+#define BRIDGE_ARB_HPRI_RING_B2		(1 << 5)
+#define BRIDGE_ARB_HPRI_RING_B1		(1 << 4)
+#define BRIDGE_ARB_HPRI_RING_B0		(1 << 3)
+#define BRIDGE_ARB_LPRI_RING_B2		(1 << 2)
+#define BRIDGE_ARB_LPRI_RING_B1		(1 << 1)
+#define BRIDGE_ARB_LPRI_RING_B0		(1 << 0)
+
+/* Bridge Bus time-out register bits definition */
+#define BRIDGE_BUS_PCI_RETRY_HLD(x)	((x) << 16)
+#define BRIDGE_BUS_PCI_RETRY_HLD_MASK	BRIDGE_BUS_PCI_RETRY_HLD(0x1f)
+#define BRIDGE_BUS_GIO_TIMEOUT		(1 << 12)
+#define BRIDGE_BUS_PCI_RETRY_CNT(x)	((x) << 0)
+#define BRIDGE_BUS_PCI_RETRY_MASK	BRIDGE_BUS_PCI_RETRY_CNT(0x3ff)
+
+/* Bridge interrupt status register bits definition */
+#define BRIDGE_ISR_MULTI_ERR		(0x1u << 31)
+#define BRIDGE_ISR_PMU_ESIZE_FAULT	(0x1 << 30)
+#define BRIDGE_ISR_UNEXP_RESP		(0x1 << 29)
+#define BRIDGE_ISR_BAD_XRESP_PKT	(0x1 << 28)
+#define BRIDGE_ISR_BAD_XREQ_PKT		(0x1 << 27)
+#define BRIDGE_ISR_RESP_XTLK_ERR	(0x1 << 26)
+#define BRIDGE_ISR_REQ_XTLK_ERR		(0x1 << 25)
+#define BRIDGE_ISR_INVLD_ADDR		(0x1 << 24)
+#define BRIDGE_ISR_UNSUPPORTED_XOP	(0x1 << 23)
+#define BRIDGE_ISR_XREQ_FIFO_OFLOW	(0x1 << 22)
+#define BRIDGE_ISR_LLP_REC_SNERR	(0x1 << 21)
+#define BRIDGE_ISR_LLP_REC_CBERR	(0x1 << 20)
+#define BRIDGE_ISR_LLP_RCTY		(0x1 << 19)
+#define BRIDGE_ISR_LLP_TX_RETRY		(0x1 << 18)
+#define BRIDGE_ISR_LLP_TCTY		(0x1 << 17)
+#define BRIDGE_ISR_SSRAM_PERR		(0x1 << 16)
+#define BRIDGE_ISR_PCI_ABORT		(0x1 << 15)
+#define BRIDGE_ISR_PCI_PARITY		(0x1 << 14)
+#define BRIDGE_ISR_PCI_SERR		(0x1 << 13)
+#define BRIDGE_ISR_PCI_PERR		(0x1 << 12)
+#define BRIDGE_ISR_PCI_MST_TIMEOUT	(0x1 << 11)
+#define BRIDGE_ISR_GIO_MST_TIMEOUT	BRIDGE_ISR_PCI_MST_TIMEOUT
+#define BRIDGE_ISR_PCI_RETRY_CNT	(0x1 << 10)
+#define BRIDGE_ISR_XREAD_REQ_TIMEOUT	(0x1 << 9)
+#define BRIDGE_ISR_GIO_B_ENBL_ERR	(0x1 << 8)
+#define BRIDGE_ISR_INT_MSK		(0xff << 0)
+#define BRIDGE_ISR_INT(x)		(0x1 << (x))
+
+#define BRIDGE_ISR_LINK_ERROR		\
+		(BRIDGE_ISR_LLP_REC_SNERR|BRIDGE_ISR_LLP_REC_CBERR|	\
+		 BRIDGE_ISR_LLP_RCTY|BRIDGE_ISR_LLP_TX_RETRY|		\
+		 BRIDGE_ISR_LLP_TCTY)
+
+#define BRIDGE_ISR_PCIBUS_PIOERR	\
+		(BRIDGE_ISR_PCI_MST_TIMEOUT|BRIDGE_ISR_PCI_ABORT)
+
+#define BRIDGE_ISR_PCIBUS_ERROR		\
+		(BRIDGE_ISR_PCIBUS_PIOERR|BRIDGE_ISR_PCI_PERR|		\
+		 BRIDGE_ISR_PCI_SERR|BRIDGE_ISR_PCI_RETRY_CNT|		\
+		 BRIDGE_ISR_PCI_PARITY)
+
+#define BRIDGE_ISR_XTALK_ERROR		\
+		(BRIDGE_ISR_XREAD_REQ_TIMEOUT|BRIDGE_ISR_XREQ_FIFO_OFLOW|\
+		 BRIDGE_ISR_UNSUPPORTED_XOP|BRIDGE_ISR_INVLD_ADDR|	\
+		 BRIDGE_ISR_REQ_XTLK_ERR|BRIDGE_ISR_RESP_XTLK_ERR|	\
+		 BRIDGE_ISR_BAD_XREQ_PKT|BRIDGE_ISR_BAD_XRESP_PKT|	\
+		 BRIDGE_ISR_UNEXP_RESP)
+
+#define BRIDGE_ISR_ERRORS		\
+		(BRIDGE_ISR_LINK_ERROR|BRIDGE_ISR_PCIBUS_ERROR|		\
+		 BRIDGE_ISR_XTALK_ERROR|BRIDGE_ISR_SSRAM_PERR|		\
+		 BRIDGE_ISR_PMU_ESIZE_FAULT)
+
+/*
+ * List of Errors which are fatal and kill the system
+ */
+#define BRIDGE_ISR_ERROR_FATAL		\
+		((BRIDGE_ISR_XTALK_ERROR & ~BRIDGE_ISR_XREAD_REQ_TIMEOUT)|\
+		 BRIDGE_ISR_PCI_SERR|BRIDGE_ISR_PCI_PARITY )
+
+#define BRIDGE_ISR_ERROR_DUMP		\
+		(BRIDGE_ISR_PCIBUS_ERROR|BRIDGE_ISR_PMU_ESIZE_FAULT|	\
+		 BRIDGE_ISR_XTALK_ERROR|BRIDGE_ISR_SSRAM_PERR)
+
+/* Bridge interrupt enable register bits definition */
+#define BRIDGE_IMR_UNEXP_RESP		BRIDGE_ISR_UNEXP_RESP
+#define BRIDGE_IMR_PMU_ESIZE_FAULT	BRIDGE_ISR_PMU_ESIZE_FAULT
+#define BRIDGE_IMR_BAD_XRESP_PKT	BRIDGE_ISR_BAD_XRESP_PKT
+#define BRIDGE_IMR_BAD_XREQ_PKT		BRIDGE_ISR_BAD_XREQ_PKT
+#define BRIDGE_IMR_RESP_XTLK_ERR	BRIDGE_ISR_RESP_XTLK_ERR
+#define BRIDGE_IMR_REQ_XTLK_ERR		BRIDGE_ISR_REQ_XTLK_ERR
+#define BRIDGE_IMR_INVLD_ADDR		BRIDGE_ISR_INVLD_ADDR
+#define BRIDGE_IMR_UNSUPPORTED_XOP	BRIDGE_ISR_UNSUPPORTED_XOP
+#define BRIDGE_IMR_XREQ_FIFO_OFLOW	BRIDGE_ISR_XREQ_FIFO_OFLOW
+#define BRIDGE_IMR_LLP_REC_SNERR	BRIDGE_ISR_LLP_REC_SNERR
+#define BRIDGE_IMR_LLP_REC_CBERR	BRIDGE_ISR_LLP_REC_CBERR
+#define BRIDGE_IMR_LLP_RCTY		BRIDGE_ISR_LLP_RCTY
+#define BRIDGE_IMR_LLP_TX_RETRY		BRIDGE_ISR_LLP_TX_RETRY
+#define BRIDGE_IMR_LLP_TCTY		BRIDGE_ISR_LLP_TCTY
+#define BRIDGE_IMR_SSRAM_PERR		BRIDGE_ISR_SSRAM_PERR
+#define BRIDGE_IMR_PCI_ABORT		BRIDGE_ISR_PCI_ABORT
+#define BRIDGE_IMR_PCI_PARITY		BRIDGE_ISR_PCI_PARITY
+#define BRIDGE_IMR_PCI_SERR		BRIDGE_ISR_PCI_SERR
+#define BRIDGE_IMR_PCI_PERR		BRIDGE_ISR_PCI_PERR
+#define BRIDGE_IMR_PCI_MST_TIMEOUT	BRIDGE_ISR_PCI_MST_TIMEOUT
+#define BRIDGE_IMR_GIO_MST_TIMEOUT	BRIDGE_ISR_GIO_MST_TIMEOUT
+#define BRIDGE_IMR_PCI_RETRY_CNT	BRIDGE_ISR_PCI_RETRY_CNT
+#define BRIDGE_IMR_XREAD_REQ_TIMEOUT	BRIDGE_ISR_XREAD_REQ_TIMEOUT
+#define BRIDGE_IMR_GIO_B_ENBL_ERR	BRIDGE_ISR_GIO_B_ENBL_ERR
+#define BRIDGE_IMR_INT_MSK		BRIDGE_ISR_INT_MSK
+#define BRIDGE_IMR_INT(x)		BRIDGE_ISR_INT(x)
+
+/* Bridge interrupt reset register bits definition */
+#define BRIDGE_IRR_MULTI_CLR		(0x1 << 6)
+#define BRIDGE_IRR_CRP_GRP_CLR		(0x1 << 5)
+#define BRIDGE_IRR_RESP_BUF_GRP_CLR	(0x1 << 4)
+#define BRIDGE_IRR_REQ_DSP_GRP_CLR	(0x1 << 3)
+#define BRIDGE_IRR_LLP_GRP_CLR		(0x1 << 2)
+#define BRIDGE_IRR_SSRAM_GRP_CLR	(0x1 << 1)
+#define BRIDGE_IRR_PCI_GRP_CLR		(0x1 << 0)
+#define BRIDGE_IRR_GIO_GRP_CLR		(0x1 << 0)
+#define BRIDGE_IRR_ALL_CLR		0x7f
+
+#define BRIDGE_IRR_CRP_GRP		(BRIDGE_ISR_UNEXP_RESP | \
+					 BRIDGE_ISR_XREQ_FIFO_OFLOW)
+#define BRIDGE_IRR_RESP_BUF_GRP		(BRIDGE_ISR_BAD_XRESP_PKT | \
+					 BRIDGE_ISR_RESP_XTLK_ERR | \
+					 BRIDGE_ISR_XREAD_REQ_TIMEOUT)
+#define BRIDGE_IRR_REQ_DSP_GRP		(BRIDGE_ISR_UNSUPPORTED_XOP | \
+					 BRIDGE_ISR_BAD_XREQ_PKT | \
+					 BRIDGE_ISR_REQ_XTLK_ERR | \
+					 BRIDGE_ISR_INVLD_ADDR)
+#define BRIDGE_IRR_LLP_GRP		(BRIDGE_ISR_LLP_REC_SNERR | \
+					 BRIDGE_ISR_LLP_REC_CBERR | \
+					 BRIDGE_ISR_LLP_RCTY | \
+					 BRIDGE_ISR_LLP_TX_RETRY | \
+					 BRIDGE_ISR_LLP_TCTY)
+#define BRIDGE_IRR_SSRAM_GRP		(BRIDGE_ISR_SSRAM_PERR | \
+					 BRIDGE_ISR_PMU_ESIZE_FAULT)
+#define BRIDGE_IRR_PCI_GRP		(BRIDGE_ISR_PCI_ABORT | \
+					 BRIDGE_ISR_PCI_PARITY | \
+					 BRIDGE_ISR_PCI_SERR | \
+					 BRIDGE_ISR_PCI_PERR | \
+					 BRIDGE_ISR_PCI_MST_TIMEOUT | \
+					 BRIDGE_ISR_PCI_RETRY_CNT)
+
+#define BRIDGE_IRR_GIO_GRP		(BRIDGE_ISR_GIO_B_ENBL_ERR | \
+					 BRIDGE_ISR_GIO_MST_TIMEOUT)
+
+/* Bridge INT_DEV register bits definition */
+#define BRIDGE_INT_DEV_SHFT(n)		((n)*3)
+#define BRIDGE_INT_DEV_MASK(n)		(0x7 << BRIDGE_INT_DEV_SHFT(n))
+#define BRIDGE_INT_DEV_SET(_dev, _line) (_dev << BRIDGE_INT_DEV_SHFT(_line))
+
+/* Bridge interrupt(x) register bits definition */
+#define BRIDGE_INT_ADDR_HOST		0x0003FF00
+#define BRIDGE_INT_ADDR_FLD		0x000000FF
+
+#define BRIDGE_TMO_PCI_RETRY_HLD_MASK	0x1f0000
+#define BRIDGE_TMO_GIO_TIMEOUT_MASK	0x001000
+#define BRIDGE_TMO_PCI_RETRY_CNT_MASK	0x0003ff
+
+#define BRIDGE_TMO_PCI_RETRY_CNT_MAX	0x3ff
+
+/*
+ * The NASID should be shifted by this amount and stored into the
+ * interrupt(x) register.
+ */
+#define BRIDGE_INT_ADDR_NASID_SHFT	8
+
+/*
+ * The BRIDGE_INT_ADDR_DEST_IO bit should be set to send an interrupt to
+ * memory.
+ */
+#define BRIDGE_INT_ADDR_DEST_IO		(1 << 17)
+#define BRIDGE_INT_ADDR_DEST_MEM	0
+#define BRIDGE_INT_ADDR_MASK		(1 << 17)
+
+/* Bridge device(x) register bits definition */
+#define BRIDGE_DEV_ERR_LOCK_EN		0x10000000
+#define BRIDGE_DEV_PAGE_CHK_DIS		0x08000000
+#define BRIDGE_DEV_FORCE_PCI_PAR	0x04000000
+#define BRIDGE_DEV_VIRTUAL_EN		0x02000000
+#define BRIDGE_DEV_PMU_WRGA_EN		0x01000000
+#define BRIDGE_DEV_DIR_WRGA_EN		0x00800000
+#define BRIDGE_DEV_DEV_SIZE		0x00400000
+#define BRIDGE_DEV_RT			0x00200000
+#define BRIDGE_DEV_SWAP_PMU		0x00100000
+#define BRIDGE_DEV_SWAP_DIR		0x00080000
+#define BRIDGE_DEV_PREF			0x00040000
+#define BRIDGE_DEV_PRECISE		0x00020000
+#define BRIDGE_DEV_COH			0x00010000
+#define BRIDGE_DEV_BARRIER		0x00008000
+#define BRIDGE_DEV_GBR			0x00004000
+#define BRIDGE_DEV_DEV_SWAP		0x00002000
+#define BRIDGE_DEV_DEV_IO_MEM		0x00001000
+#define BRIDGE_DEV_OFF_MASK		0x00000fff
+#define BRIDGE_DEV_OFF_ADDR_SHFT	20
+
+#define BRIDGE_DEV_PMU_BITS		(BRIDGE_DEV_PMU_WRGA_EN		| \
+					 BRIDGE_DEV_SWAP_PMU)
+#define BRIDGE_DEV_D32_BITS		(BRIDGE_DEV_DIR_WRGA_EN		| \
+					 BRIDGE_DEV_SWAP_DIR		| \
+					 BRIDGE_DEV_PREF		| \
+					 BRIDGE_DEV_PRECISE		| \
+					 BRIDGE_DEV_COH			| \
+					 BRIDGE_DEV_BARRIER)
+#define BRIDGE_DEV_D64_BITS		(BRIDGE_DEV_DIR_WRGA_EN		| \
+					 BRIDGE_DEV_SWAP_DIR		| \
+					 BRIDGE_DEV_COH			| \
+					 BRIDGE_DEV_BARRIER)
+
+/* Bridge Error Upper register bit field definition */
+#define BRIDGE_ERRUPPR_DEVMASTER	(0x1 << 20)	/* Device was master */
+#define BRIDGE_ERRUPPR_PCIVDEV		(0x1 << 19)	/* Virtual Req value */
+#define BRIDGE_ERRUPPR_DEVNUM_SHFT	(16)
+#define BRIDGE_ERRUPPR_DEVNUM_MASK	(0x7 << BRIDGE_ERRUPPR_DEVNUM_SHFT)
+#define BRIDGE_ERRUPPR_DEVICE(err)	(((err) >> BRIDGE_ERRUPPR_DEVNUM_SHFT) & 0x7)
+#define BRIDGE_ERRUPPR_ADDRMASK		(0xFFFF)
+
+/* Bridge interrupt mode register bits definition */
+#define BRIDGE_INTMODE_CLR_PKT_EN(x)	(0x1 << (x))
+
+/* this should be written to the xbow's link_control(x) register */
+#define BRIDGE_CREDIT	3
+
+/* RRB assignment register */
+#define BRIDGE_RRB_EN	0x8	/* after shifting down */
+#define BRIDGE_RRB_DEV	0x7	/* after shifting down */
+#define BRIDGE_RRB_VDEV 0x4	/* after shifting down */
+#define BRIDGE_RRB_PDEV 0x3	/* after shifting down */
+
+/* RRB status register */
+#define BRIDGE_RRB_VALID(r)	(0x00010000<<(r))
+#define BRIDGE_RRB_INUSE(r)	(0x00000001<<(r))
+
+/* RRB clear register */
+#define BRIDGE_RRB_CLEAR(r)	(0x00000001<<(r))
+
+/* xbox system controller declarations */
+#define XBOX_BRIDGE_WID		8
+#define FLASH_PROM1_BASE	0xE00000 /* To read the xbox sysctlr status */
+#define XBOX_RPS_EXISTS		1 << 6	 /* RPS bit in status register */
+#define XBOX_RPS_FAIL		1 << 4	 /* RPS status bit in register */
+
+/* ========================================================================
+ */
+/*
+ * Macros for Xtalk to Bridge bus (PCI/GIO) PIO
+ * refer to section 4.2.1 of Bridge Spec for xtalk to PCI/GIO PIO mappings
+ */
+/* XTALK addresses that map into Bridge Bus addr space */
+#define BRIDGE_PIO32_XTALK_ALIAS_BASE	0x000040000000L
+#define BRIDGE_PIO32_XTALK_ALIAS_LIMIT	0x00007FFFFFFFL
+#define BRIDGE_PIO64_XTALK_ALIAS_BASE	0x000080000000L
+#define BRIDGE_PIO64_XTALK_ALIAS_LIMIT	0x0000BFFFFFFFL
+#define BRIDGE_PCIIO_XTALK_ALIAS_BASE	0x000100000000L
+#define BRIDGE_PCIIO_XTALK_ALIAS_LIMIT	0x0001FFFFFFFFL
+
+/* Ranges of PCI bus space that can be accessed via PIO from xtalk */
+#define BRIDGE_MIN_PIO_ADDR_MEM		0x00000000	/* 1G PCI memory space */
+#define BRIDGE_MAX_PIO_ADDR_MEM		0x3fffffff
+#define BRIDGE_MIN_PIO_ADDR_IO		0x00000000	/* 4G PCI IO space */
+#define BRIDGE_MAX_PIO_ADDR_IO		0xffffffff
+
+/* XTALK addresses that map into PCI addresses */
+#define BRIDGE_PCI_MEM32_BASE		BRIDGE_PIO32_XTALK_ALIAS_BASE
+#define BRIDGE_PCI_MEM32_LIMIT		BRIDGE_PIO32_XTALK_ALIAS_LIMIT
+#define BRIDGE_PCI_MEM64_BASE		BRIDGE_PIO64_XTALK_ALIAS_BASE
+#define BRIDGE_PCI_MEM64_LIMIT		BRIDGE_PIO64_XTALK_ALIAS_LIMIT
+#define BRIDGE_PCI_IO_BASE		BRIDGE_PCIIO_XTALK_ALIAS_BASE
+#define BRIDGE_PCI_IO_LIMIT		BRIDGE_PCIIO_XTALK_ALIAS_LIMIT
+
+/*
+ * Macros for Bridge bus (PCI/GIO) to Xtalk DMA
+ */
+/* Bridge Bus DMA addresses */
+#define BRIDGE_LOCAL_BASE		0
+#define BRIDGE_DMA_MAPPED_BASE		0x40000000
+#define BRIDGE_DMA_MAPPED_SIZE		0x40000000	/* 1G Bytes */
+#define BRIDGE_DMA_DIRECT_BASE		0x80000000
+#define BRIDGE_DMA_DIRECT_SIZE		0x80000000	/* 2G Bytes */
+
+#define PCI32_LOCAL_BASE		BRIDGE_LOCAL_BASE
+
+/* PCI addresses of regions decoded by Bridge for DMA */
+#define PCI32_MAPPED_BASE		BRIDGE_DMA_MAPPED_BASE
+#define PCI32_DIRECT_BASE		BRIDGE_DMA_DIRECT_BASE
+
+#define IS_PCI32_LOCAL(x)	((ulong_t)(x) < PCI32_MAPPED_BASE)
+#define IS_PCI32_MAPPED(x)	((ulong_t)(x) < PCI32_DIRECT_BASE && \
+					(ulong_t)(x) >= PCI32_MAPPED_BASE)
+#define IS_PCI32_DIRECT(x)	((ulong_t)(x) >= PCI32_MAPPED_BASE)
+#define IS_PCI64(x)		((ulong_t)(x) >= PCI64_BASE)
+
+/*
+ * The GIO address space.
+ */
+/* Xtalk to GIO PIO */
+#define BRIDGE_GIO_MEM32_BASE		BRIDGE_PIO32_XTALK_ALIAS_BASE
+#define BRIDGE_GIO_MEM32_LIMIT		BRIDGE_PIO32_XTALK_ALIAS_LIMIT
+
+#define GIO_LOCAL_BASE			BRIDGE_LOCAL_BASE
+
+/* GIO addresses of regions decoded by Bridge for DMA */
+#define GIO_MAPPED_BASE			BRIDGE_DMA_MAPPED_BASE
+#define GIO_DIRECT_BASE			BRIDGE_DMA_DIRECT_BASE
+
+#define IS_GIO_LOCAL(x)		((ulong_t)(x) < GIO_MAPPED_BASE)
+#define IS_GIO_MAPPED(x)	((ulong_t)(x) < GIO_DIRECT_BASE && \
+					(ulong_t)(x) >= GIO_MAPPED_BASE)
+#define IS_GIO_DIRECT(x)	((ulong_t)(x) >= GIO_MAPPED_BASE)
+
+/* PCI to xtalk mapping */
+
+/* given a DIR_OFF value and a pci/gio 32 bits direct address, determine
+ * which xtalk address is accessed
+ */
+#define BRIDGE_DIRECT_32_SEG_SIZE	BRIDGE_DMA_DIRECT_SIZE
+#define BRIDGE_DIRECT_32_TO_XTALK(dir_off,adr)		\
+	((dir_off) * BRIDGE_DIRECT_32_SEG_SIZE +	\
+		((adr) & (BRIDGE_DIRECT_32_SEG_SIZE - 1)) + PHYS_RAMBASE)
+
+/* 64-bit address attribute masks */
+#define PCI64_ATTR_TARG_MASK	0xf000000000000000
+#define PCI64_ATTR_TARG_SHFT	60
+#define PCI64_ATTR_PREF		0x0800000000000000
+#define PCI64_ATTR_PREC		0x0400000000000000
+#define PCI64_ATTR_VIRTUAL	0x0200000000000000
+#define PCI64_ATTR_BAR		0x0100000000000000
+#define PCI64_ATTR_RMF_MASK	0x00ff000000000000
+#define PCI64_ATTR_RMF_SHFT	48
+
+struct bridge_controller {
+	struct resource		busn;
+	struct bridge_regs	*base;
+	unsigned long		baddr;
+	unsigned long		intr_addr;
+	struct irq_domain	*domain;
+	unsigned int		pci_int[8][2];
+	unsigned int		int_mapping[8][2];
+	u32			ioc3_sid[8];
+	nasid_t			nasid;
+};
+
+#define BRIDGE_CONTROLLER(bus) \
+	((struct bridge_controller *)((bus)->sysdata))
+
+#define bridge_read(bc, reg)		__raw_readl(&bc->base->reg)
+#define bridge_write(bc, reg, val)	__raw_writel(val, &bc->base->reg)
+#define bridge_set(bc, reg, val)	\
+	__raw_writel(__raw_readl(&bc->base->reg) | (val), &bc->base->reg)
+#define bridge_clr(bc, reg, val)	\
+	__raw_writel(__raw_readl(&bc->base->reg) & ~(val), &bc->base->reg)
+
+#endif /* _ASM_PCI_BRIDGE_H */
diff --git a/arch/mips/include/asm/perf_event.h b/arch/mips/include/asm/perf_event.h
new file mode 100644
index 000000000..0babf6bbb
--- /dev/null
+++ b/arch/mips/include/asm/perf_event.h
@@ -0,0 +1,12 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * linux/arch/mips/include/asm/perf_event.h
+ *
+ * Copyright (C) 2010 MIPS Technologies, Inc.
+ * Author: Deng-Cheng Zhu
+ */
+
+#ifndef __MIPS_PERF_EVENT_H__
+#define __MIPS_PERF_EVENT_H__
+/* Leave it empty here. The file is required by linux/perf_event.h */
+#endif /* __MIPS_PERF_EVENT_H__ */
diff --git a/arch/mips/include/asm/pgalloc.h b/arch/mips/include/asm/pgalloc.h
new file mode 100644
index 000000000..796035784
--- /dev/null
+++ b/arch/mips/include/asm/pgalloc.h
@@ -0,0 +1,111 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994 - 2001, 2003 by Ralf Baechle
+ * Copyright (C) 1999, 2000, 2001 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_PGALLOC_H
+#define _ASM_PGALLOC_H
+
+#include <linux/highmem.h>
+#include <linux/mm.h>
+#include <linux/sched.h>
+
+#define __HAVE_ARCH_PMD_ALLOC_ONE
+#define __HAVE_ARCH_PUD_ALLOC_ONE
+#define __HAVE_ARCH_PGD_FREE
+#include <asm-generic/pgalloc.h>
+
+static inline void pmd_populate_kernel(struct mm_struct *mm, pmd_t *pmd,
+	pte_t *pte)
+{
+	set_pmd(pmd, __pmd((unsigned long)pte));
+}
+
+static inline void pmd_populate(struct mm_struct *mm, pmd_t *pmd,
+	pgtable_t pte)
+{
+	set_pmd(pmd, __pmd((unsigned long)page_address(pte)));
+}
+
+/*
+ * Initialize a new pmd table with invalid pointers.
+ */
+extern void pmd_init(unsigned long page, unsigned long pagetable);
+
+#ifndef __PAGETABLE_PMD_FOLDED
+
+static inline void pud_populate(struct mm_struct *mm, pud_t *pud, pmd_t *pmd)
+{
+	set_pud(pud, __pud((unsigned long)pmd));
+}
+#endif
+
+/*
+ * Initialize a new pgd / pmd table with invalid pointers.
+ */
+extern void pgd_init(unsigned long page);
+extern pgd_t *pgd_alloc(struct mm_struct *mm);
+
+static inline void pgd_free(struct mm_struct *mm, pgd_t *pgd)
+{
+	free_pages((unsigned long)pgd, PGD_TABLE_ORDER);
+}
+
+#define __pte_free_tlb(tlb,pte,address)			\
+do {							\
+	pgtable_pte_page_dtor(pte);			\
+	tlb_remove_page((tlb), pte);			\
+} while (0)
+
+#ifndef __PAGETABLE_PMD_FOLDED
+
+static inline pmd_t *pmd_alloc_one(struct mm_struct *mm, unsigned long address)
+{
+	pmd_t *pmd;
+	struct page *pg;
+
+	pg = alloc_pages(GFP_KERNEL_ACCOUNT, PMD_TABLE_ORDER);
+	if (!pg)
+		return NULL;
+
+	if (!pgtable_pmd_page_ctor(pg)) {
+		__free_pages(pg, PMD_TABLE_ORDER);
+		return NULL;
+	}
+
+	pmd = (pmd_t *)page_address(pg);
+	pmd_init((unsigned long)pmd, (unsigned long)invalid_pte_table);
+	return pmd;
+}
+
+#define __pmd_free_tlb(tlb, x, addr)	pmd_free((tlb)->mm, x)
+
+#endif
+
+#ifndef __PAGETABLE_PUD_FOLDED
+
+static inline pud_t *pud_alloc_one(struct mm_struct *mm, unsigned long address)
+{
+	pud_t *pud;
+
+	pud = (pud_t *) __get_free_pages(GFP_KERNEL, PUD_TABLE_ORDER);
+	if (pud)
+		pud_init((unsigned long)pud, (unsigned long)invalid_pmd_table);
+	return pud;
+}
+
+static inline void p4d_populate(struct mm_struct *mm, p4d_t *p4d, pud_t *pud)
+{
+	set_p4d(p4d, __p4d((unsigned long)pud));
+}
+
+#define __pud_free_tlb(tlb, x, addr)	pud_free((tlb)->mm, x)
+
+#endif /* __PAGETABLE_PUD_FOLDED */
+
+extern void pagetable_init(void);
+
+#endif /* _ASM_PGALLOC_H */
diff --git a/arch/mips/include/asm/pgtable-32.h b/arch/mips/include/asm/pgtable-32.h
new file mode 100644
index 000000000..b40a0e69f
--- /dev/null
+++ b/arch/mips/include/asm/pgtable-32.h
@@ -0,0 +1,241 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994, 95, 96, 97, 98, 99, 2000, 2003 Ralf Baechle
+ * Copyright (C) 1999, 2000, 2001 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_PGTABLE_32_H
+#define _ASM_PGTABLE_32_H
+
+#include <asm/addrspace.h>
+#include <asm/page.h>
+
+#include <linux/linkage.h>
+#include <asm/cachectl.h>
+#include <asm/fixmap.h>
+
+#include <asm-generic/pgtable-nopmd.h>
+
+#ifdef CONFIG_HIGHMEM
+#include <asm/highmem.h>
+#endif
+
+/*
+ * Regarding 32-bit MIPS huge page support (and the tradeoff it entails):
+ *
+ *  We use the same huge page sizes as 64-bit MIPS. Assuming a 4KB page size,
+ * our 2-level table layout would normally have a PGD entry cover a contiguous
+ * 4MB virtual address region (pointing to a 4KB PTE page of 1,024 32-bit pte_t
+ * pointers, each pointing to a 4KB physical page). The problem is that 4MB,
+ * spanning both halves of a TLB EntryLo0,1 pair, requires 2MB hardware page
+ * support, not one of the standard supported sizes (1MB,4MB,16MB,...).
+ *  To correct for this, when huge pages are enabled, we halve the number of
+ * pointers a PTE page holds, making its last half go to waste. Correspondingly,
+ * we double the number of PGD pages. Overall, page table memory overhead
+ * increases to match 64-bit MIPS, but PTE lookups remain CPU cache-friendly.
+ *
+ * NOTE: We don't yet support huge pages if extended-addressing is enabled
+ *       (i.e. EVA, XPA, 36-bit Alchemy/Netlogic).
+ */
+
+extern int temp_tlb_entry;
+
+/*
+ * - add_temporary_entry() add a temporary TLB entry. We use TLB entries
+ *	starting at the top and working down. This is for populating the
+ *	TLB before trap_init() puts the TLB miss handler in place. It
+ *	should be used only for entries matching the actual page tables,
+ *	to prevent inconsistencies.
+ */
+extern int add_temporary_entry(unsigned long entrylo0, unsigned long entrylo1,
+			       unsigned long entryhi, unsigned long pagemask);
+
+/*
+ * Basically we have the same two-level (which is the logical three level
+ * Linux page table layout folded) page tables as the i386.  Some day
+ * when we have proper page coloring support we can have a 1% quicker
+ * tlb refill handling mechanism, but for now it is a bit slower but
+ * works even with the cache aliasing problem the R4k and above have.
+ */
+
+/* PGDIR_SHIFT determines what a third-level page table entry can map */
+#if defined(CONFIG_MIPS_HUGE_TLB_SUPPORT) && !defined(CONFIG_PHYS_ADDR_T_64BIT)
+# define PGDIR_SHIFT	(2 * PAGE_SHIFT - PTE_T_LOG2 - 1)
+#else
+# define PGDIR_SHIFT	(2 * PAGE_SHIFT - PTE_T_LOG2)
+#endif
+
+#define PGDIR_SIZE	(1UL << PGDIR_SHIFT)
+#define PGDIR_MASK	(~(PGDIR_SIZE-1))
+
+/*
+ * Entries per page directory level: we use two-level, so
+ * we don't really have any PUD/PMD directory physically.
+ */
+#if defined(CONFIG_MIPS_HUGE_TLB_SUPPORT) && !defined(CONFIG_PHYS_ADDR_T_64BIT)
+# define __PGD_TABLE_ORDER (32 - 3 * PAGE_SHIFT + PGD_T_LOG2 + PTE_T_LOG2 + 1)
+#else
+# define __PGD_TABLE_ORDER (32 - 3 * PAGE_SHIFT + PGD_T_LOG2 + PTE_T_LOG2)
+#endif
+
+#define PGD_TABLE_ORDER	(__PGD_TABLE_ORDER >= 0 ? __PGD_TABLE_ORDER : 0)
+#define PUD_TABLE_ORDER	aieeee_attempt_to_allocate_pud
+#define PMD_TABLE_ORDER	aieeee_attempt_to_allocate_pmd
+
+#define PTRS_PER_PGD	(USER_PTRS_PER_PGD * 2)
+#if defined(CONFIG_MIPS_HUGE_TLB_SUPPORT) && !defined(CONFIG_PHYS_ADDR_T_64BIT)
+# define PTRS_PER_PTE	(PAGE_SIZE / sizeof(pte_t) / 2)
+#else
+# define PTRS_PER_PTE	(PAGE_SIZE / sizeof(pte_t))
+#endif
+
+#define USER_PTRS_PER_PGD	(0x80000000UL/PGDIR_SIZE)
+
+#define VMALLOC_START	  MAP_BASE
+
+#define PKMAP_END	((FIXADDR_START) & ~((LAST_PKMAP << PAGE_SHIFT)-1))
+#define PKMAP_BASE	(PKMAP_END - PAGE_SIZE * LAST_PKMAP)
+
+#ifdef CONFIG_HIGHMEM
+# define VMALLOC_END	(PKMAP_BASE-2*PAGE_SIZE)
+#else
+# define VMALLOC_END	(FIXADDR_START-2*PAGE_SIZE)
+#endif
+
+#ifdef CONFIG_PHYS_ADDR_T_64BIT
+#define pte_ERROR(e) \
+	printk("%s:%d: bad pte %016Lx.\n", __FILE__, __LINE__, pte_val(e))
+#else
+#define pte_ERROR(e) \
+	printk("%s:%d: bad pte %08lx.\n", __FILE__, __LINE__, pte_val(e))
+#endif
+#define pgd_ERROR(e) \
+	printk("%s:%d: bad pgd %08lx.\n", __FILE__, __LINE__, pgd_val(e))
+
+extern void load_pgd(unsigned long pg_dir);
+
+extern pte_t invalid_pte_table[PTRS_PER_PTE];
+
+/*
+ * Empty pgd/pmd entries point to the invalid_pte_table.
+ */
+static inline int pmd_none(pmd_t pmd)
+{
+	return pmd_val(pmd) == (unsigned long) invalid_pte_table;
+}
+
+static inline int pmd_bad(pmd_t pmd)
+{
+#ifdef CONFIG_MIPS_HUGE_TLB_SUPPORT
+	/* pmd_huge(pmd) but inline */
+	if (unlikely(pmd_val(pmd) & _PAGE_HUGE))
+		return 0;
+#endif
+
+	if (unlikely(pmd_val(pmd) & ~PAGE_MASK))
+		return 1;
+
+	return 0;
+}
+
+static inline int pmd_present(pmd_t pmd)
+{
+	return pmd_val(pmd) != (unsigned long) invalid_pte_table;
+}
+
+static inline void pmd_clear(pmd_t *pmdp)
+{
+	pmd_val(*pmdp) = ((unsigned long) invalid_pte_table);
+}
+
+#if defined(CONFIG_XPA)
+
+#define MAX_POSSIBLE_PHYSMEM_BITS 40
+#define pte_pfn(x)		(((unsigned long)((x).pte_high >> _PFN_SHIFT)) | (unsigned long)((x).pte_low << _PAGE_PRESENT_SHIFT))
+static inline pte_t
+pfn_pte(unsigned long pfn, pgprot_t prot)
+{
+	pte_t pte;
+
+	pte.pte_low = (pfn >> _PAGE_PRESENT_SHIFT) |
+				(pgprot_val(prot) & ~_PFNX_MASK);
+	pte.pte_high = (pfn << _PFN_SHIFT) |
+				(pgprot_val(prot) & ~_PFN_MASK);
+	return pte;
+}
+
+#elif defined(CONFIG_PHYS_ADDR_T_64BIT) && defined(CONFIG_CPU_MIPS32)
+
+#define MAX_POSSIBLE_PHYSMEM_BITS 36
+#define pte_pfn(x)		((unsigned long)((x).pte_high >> 6))
+
+static inline pte_t pfn_pte(unsigned long pfn, pgprot_t prot)
+{
+	pte_t pte;
+
+	pte.pte_high = (pfn << 6) | (pgprot_val(prot) & 0x3f);
+	pte.pte_low = pgprot_val(prot);
+
+	return pte;
+}
+
+#else
+
+#define MAX_POSSIBLE_PHYSMEM_BITS 32
+#define pte_pfn(x)		((unsigned long)((x).pte >> _PFN_SHIFT))
+#define pfn_pte(pfn, prot)	__pte(((unsigned long long)(pfn) << _PFN_SHIFT) | pgprot_val(prot))
+#define pfn_pmd(pfn, prot)	__pmd(((unsigned long long)(pfn) << _PFN_SHIFT) | pgprot_val(prot))
+#endif /* defined(CONFIG_PHYS_ADDR_T_64BIT) && defined(CONFIG_CPU_MIPS32) */
+
+#define pte_page(x)		pfn_to_page(pte_pfn(x))
+
+#if defined(CONFIG_CPU_R3K_TLB)
+
+/* Swap entries must have VALID bit cleared. */
+#define __swp_type(x)			(((x).val >> 10) & 0x1f)
+#define __swp_offset(x)			((x).val >> 15)
+#define __swp_entry(type,offset)	((swp_entry_t) { ((type) << 10) | ((offset) << 15) })
+#define __pte_to_swp_entry(pte)		((swp_entry_t) { pte_val(pte) })
+#define __swp_entry_to_pte(x)		((pte_t) { (x).val })
+
+#else
+
+#if defined(CONFIG_XPA)
+
+/* Swap entries must have VALID and GLOBAL bits cleared. */
+#define __swp_type(x)			(((x).val >> 4) & 0x1f)
+#define __swp_offset(x)			 ((x).val >> 9)
+#define __swp_entry(type,offset)	((swp_entry_t)  { ((type) << 4) | ((offset) << 9) })
+#define __pte_to_swp_entry(pte)		((swp_entry_t) { (pte).pte_high })
+#define __swp_entry_to_pte(x)		((pte_t) { 0, (x).val })
+
+#elif defined(CONFIG_PHYS_ADDR_T_64BIT) && defined(CONFIG_CPU_MIPS32)
+
+/* Swap entries must have VALID and GLOBAL bits cleared. */
+#define __swp_type(x)			(((x).val >> 2) & 0x1f)
+#define __swp_offset(x)			 ((x).val >> 7)
+#define __swp_entry(type, offset)	((swp_entry_t)  { ((type) << 2) | ((offset) << 7) })
+#define __pte_to_swp_entry(pte)		((swp_entry_t) { (pte).pte_high })
+#define __swp_entry_to_pte(x)		((pte_t) { 0, (x).val })
+
+#else
+/*
+ * Constraints:
+ *      _PAGE_PRESENT at bit 0
+ *      _PAGE_MODIFIED at bit 4
+ *      _PAGE_GLOBAL at bit 6
+ *      _PAGE_VALID at bit 7
+ */
+#define __swp_type(x)			(((x).val >> 8) & 0x1f)
+#define __swp_offset(x)			 ((x).val >> 13)
+#define __swp_entry(type,offset)	((swp_entry_t)	{ ((type) << 8) | ((offset) << 13) })
+#define __pte_to_swp_entry(pte)		((swp_entry_t) { pte_val(pte) })
+#define __swp_entry_to_pte(x)		((pte_t) { (x).val })
+
+#endif /* defined(CONFIG_PHYS_ADDR_T_64BIT) && defined(CONFIG_CPU_MIPS32) */
+
+#endif /* defined(CONFIG_CPU_R3K_TLB) */
+
+#endif /* _ASM_PGTABLE_32_H */
diff --git a/arch/mips/include/asm/pgtable-64.h b/arch/mips/include/asm/pgtable-64.h
new file mode 100644
index 000000000..436c29d69
--- /dev/null
+++ b/arch/mips/include/asm/pgtable-64.h
@@ -0,0 +1,335 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994, 95, 96, 97, 98, 99, 2000, 2003 Ralf Baechle
+ * Copyright (C) 1999, 2000, 2001 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_PGTABLE_64_H
+#define _ASM_PGTABLE_64_H
+
+#include <linux/compiler.h>
+#include <linux/linkage.h>
+
+#include <asm/addrspace.h>
+#include <asm/page.h>
+#include <asm/cachectl.h>
+#include <asm/fixmap.h>
+
+#if CONFIG_PGTABLE_LEVELS == 2
+#include <asm-generic/pgtable-nopmd.h>
+#elif CONFIG_PGTABLE_LEVELS == 3
+#include <asm-generic/pgtable-nopud.h>
+#else
+#include <asm-generic/pgtable-nop4d.h>
+#endif
+
+/*
+ * Each address space has 2 4K pages as its page directory, giving 1024
+ * (== PTRS_PER_PGD) 8 byte pointers to pmd tables. Each pmd table is a
+ * single 4K page, giving 512 (== PTRS_PER_PMD) 8 byte pointers to page
+ * tables. Each page table is also a single 4K page, giving 512 (==
+ * PTRS_PER_PTE) 8 byte ptes. Each pud entry is initialized to point to
+ * invalid_pmd_table, each pmd entry is initialized to point to
+ * invalid_pte_table, each pte is initialized to 0.
+ *
+ * Kernel mappings: kernel mappings are held in the swapper_pg_table.
+ * The layout is identical to userspace except it's indexed with the
+ * fault address - VMALLOC_START.
+ */
+
+
+/* PGDIR_SHIFT determines what a third-level page table entry can map */
+#ifdef __PAGETABLE_PMD_FOLDED
+#define PGDIR_SHIFT	(PAGE_SHIFT + PAGE_SHIFT - 3)
+#else
+
+/* PMD_SHIFT determines the size of the area a second-level page table can map */
+#define PMD_SHIFT	(PAGE_SHIFT + (PAGE_SHIFT - 3))
+#define PMD_SIZE	(1UL << PMD_SHIFT)
+#define PMD_MASK	(~(PMD_SIZE-1))
+
+# ifdef __PAGETABLE_PUD_FOLDED
+# define PGDIR_SHIFT	(PMD_SHIFT + (PAGE_SHIFT + PMD_TABLE_ORDER - 3))
+# endif
+#endif
+
+#ifndef __PAGETABLE_PUD_FOLDED
+#define PUD_SHIFT	(PMD_SHIFT + (PAGE_SHIFT + PMD_TABLE_ORDER - 3))
+#define PUD_SIZE	(1UL << PUD_SHIFT)
+#define PUD_MASK	(~(PUD_SIZE-1))
+#define PGDIR_SHIFT	(PUD_SHIFT + (PAGE_SHIFT + PUD_TABLE_ORDER - 3))
+#endif
+
+#define PGDIR_SIZE	(1UL << PGDIR_SHIFT)
+#define PGDIR_MASK	(~(PGDIR_SIZE-1))
+
+/*
+ * For 4kB page size we use a 3 level page tree and an 8kB pud, which
+ * permits us mapping 40 bits of virtual address space.
+ *
+ * We used to implement 41 bits by having an order 1 pmd level but that seemed
+ * rather pointless.
+ *
+ * For 8kB page size we use a 3 level page tree which permits a total of
+ * 8TB of address space.  Alternatively a 33-bit / 8GB organization using
+ * two levels would be easy to implement.
+ *
+ * For 16kB page size we use a 2 level page tree which permits a total of
+ * 36 bits of virtual address space.  We could add a third level but it seems
+ * like at the moment there's no need for this.
+ *
+ * For 64kB page size we use a 2 level page table tree for a total of 42 bits
+ * of virtual address space.
+ */
+#ifdef CONFIG_PAGE_SIZE_4KB
+# ifdef CONFIG_MIPS_VA_BITS_48
+#  define PGD_TABLE_ORDER	0
+#  define PUD_TABLE_ORDER	0
+# else
+#  define PGD_TABLE_ORDER	1
+#  define PUD_TABLE_ORDER	aieeee_attempt_to_allocate_pud
+# endif
+#define PMD_TABLE_ORDER		0
+#endif
+#ifdef CONFIG_PAGE_SIZE_8KB
+#define PGD_TABLE_ORDER		0
+#define PUD_TABLE_ORDER		aieeee_attempt_to_allocate_pud
+#define PMD_TABLE_ORDER		0
+#endif
+#ifdef CONFIG_PAGE_SIZE_16KB
+#ifdef CONFIG_MIPS_VA_BITS_48
+#define PGD_TABLE_ORDER		1
+#else
+#define PGD_TABLE_ORDER		0
+#endif
+#define PUD_TABLE_ORDER		aieeee_attempt_to_allocate_pud
+#define PMD_TABLE_ORDER		0
+#endif
+#ifdef CONFIG_PAGE_SIZE_32KB
+#define PGD_TABLE_ORDER		0
+#define PUD_TABLE_ORDER		aieeee_attempt_to_allocate_pud
+#define PMD_TABLE_ORDER		0
+#endif
+#ifdef CONFIG_PAGE_SIZE_64KB
+#define PGD_TABLE_ORDER		0
+#define PUD_TABLE_ORDER		aieeee_attempt_to_allocate_pud
+#ifdef CONFIG_MIPS_VA_BITS_48
+#define PMD_TABLE_ORDER		0
+#else
+#define PMD_TABLE_ORDER		aieeee_attempt_to_allocate_pmd
+#endif
+#endif
+
+#define PTRS_PER_PGD	((PAGE_SIZE << PGD_TABLE_ORDER) / sizeof(pgd_t))
+#ifndef __PAGETABLE_PUD_FOLDED
+#define PTRS_PER_PUD	((PAGE_SIZE << PUD_TABLE_ORDER) / sizeof(pud_t))
+#endif
+#ifndef __PAGETABLE_PMD_FOLDED
+#define PTRS_PER_PMD	((PAGE_SIZE << PMD_TABLE_ORDER) / sizeof(pmd_t))
+#endif
+#define PTRS_PER_PTE	(PAGE_SIZE / sizeof(pte_t))
+
+#define USER_PTRS_PER_PGD       ((TASK_SIZE64 / PGDIR_SIZE)?(TASK_SIZE64 / PGDIR_SIZE):1)
+
+/*
+ * TLB refill handlers also map the vmalloc area into xuseg.  Avoid
+ * the first couple of pages so NULL pointer dereferences will still
+ * reliably trap.
+ */
+#define VMALLOC_START		(MAP_BASE + (2 * PAGE_SIZE))
+#define VMALLOC_END	\
+	(MAP_BASE + \
+	 min(PTRS_PER_PGD * PTRS_PER_PUD * PTRS_PER_PMD * PTRS_PER_PTE * PAGE_SIZE, \
+	     (1UL << cpu_vmbits)) - (1UL << 32))
+
+#if defined(CONFIG_MODULES) && defined(KBUILD_64BIT_SYM32) && \
+	VMALLOC_START != CKSSEG
+/* Load modules into 32bit-compatible segment. */
+#define MODULE_START	CKSSEG
+#define MODULE_END	(FIXADDR_START-2*PAGE_SIZE)
+#endif
+
+#define pte_ERROR(e) \
+	printk("%s:%d: bad pte %016lx.\n", __FILE__, __LINE__, pte_val(e))
+#ifndef __PAGETABLE_PMD_FOLDED
+#define pmd_ERROR(e) \
+	printk("%s:%d: bad pmd %016lx.\n", __FILE__, __LINE__, pmd_val(e))
+#endif
+#ifndef __PAGETABLE_PUD_FOLDED
+#define pud_ERROR(e) \
+	printk("%s:%d: bad pud %016lx.\n", __FILE__, __LINE__, pud_val(e))
+#endif
+#define pgd_ERROR(e) \
+	printk("%s:%d: bad pgd %016lx.\n", __FILE__, __LINE__, pgd_val(e))
+
+extern pte_t invalid_pte_table[PTRS_PER_PTE];
+
+#ifndef __PAGETABLE_PUD_FOLDED
+/*
+ * For 4-level pagetables we defines these ourselves, for 3-level the
+ * definitions are below, for 2-level the
+ * definitions are supplied by <asm-generic/pgtable-nopmd.h>.
+ */
+typedef struct { unsigned long pud; } pud_t;
+#define pud_val(x)	((x).pud)
+#define __pud(x)	((pud_t) { (x) })
+
+extern pud_t invalid_pud_table[PTRS_PER_PUD];
+
+/*
+ * Empty pgd entries point to the invalid_pud_table.
+ */
+static inline int p4d_none(p4d_t p4d)
+{
+	return p4d_val(p4d) == (unsigned long)invalid_pud_table;
+}
+
+static inline int p4d_bad(p4d_t p4d)
+{
+	if (unlikely(p4d_val(p4d) & ~PAGE_MASK))
+		return 1;
+
+	return 0;
+}
+
+static inline int p4d_present(p4d_t p4d)
+{
+	return p4d_val(p4d) != (unsigned long)invalid_pud_table;
+}
+
+static inline void p4d_clear(p4d_t *p4dp)
+{
+	p4d_val(*p4dp) = (unsigned long)invalid_pud_table;
+}
+
+static inline pud_t *p4d_pgtable(p4d_t p4d)
+{
+	return (pud_t *)p4d_val(p4d);
+}
+
+#define p4d_phys(p4d)		virt_to_phys((void *)p4d_val(p4d))
+#define p4d_page(p4d)		(pfn_to_page(p4d_phys(p4d) >> PAGE_SHIFT))
+
+#define p4d_index(address)	(((address) >> P4D_SHIFT) & (PTRS_PER_P4D - 1))
+
+static inline void set_p4d(p4d_t *p4d, p4d_t p4dval)
+{
+	*p4d = p4dval;
+}
+
+#endif
+
+#ifndef __PAGETABLE_PMD_FOLDED
+/*
+ * For 3-level pagetables we defines these ourselves, for 2-level the
+ * definitions are supplied by <asm-generic/pgtable-nopmd.h>.
+ */
+typedef struct { unsigned long pmd; } pmd_t;
+#define pmd_val(x)	((x).pmd)
+#define __pmd(x)	((pmd_t) { (x) } )
+
+
+extern pmd_t invalid_pmd_table[PTRS_PER_PMD];
+#endif
+
+/*
+ * Empty pgd/pmd entries point to the invalid_pte_table.
+ */
+static inline int pmd_none(pmd_t pmd)
+{
+	return pmd_val(pmd) == (unsigned long) invalid_pte_table;
+}
+
+static inline int pmd_bad(pmd_t pmd)
+{
+#ifdef CONFIG_MIPS_HUGE_TLB_SUPPORT
+	/* pmd_huge(pmd) but inline */
+	if (unlikely(pmd_val(pmd) & _PAGE_HUGE))
+		return 0;
+#endif
+
+	if (unlikely(pmd_val(pmd) & ~PAGE_MASK))
+		return 1;
+
+	return 0;
+}
+
+static inline int pmd_present(pmd_t pmd)
+{
+#ifdef CONFIG_MIPS_HUGE_TLB_SUPPORT
+	if (unlikely(pmd_val(pmd) & _PAGE_HUGE))
+		return pmd_val(pmd) & _PAGE_PRESENT;
+#endif
+
+	return pmd_val(pmd) != (unsigned long) invalid_pte_table;
+}
+
+static inline void pmd_clear(pmd_t *pmdp)
+{
+	pmd_val(*pmdp) = ((unsigned long) invalid_pte_table);
+}
+#ifndef __PAGETABLE_PMD_FOLDED
+
+/*
+ * Empty pud entries point to the invalid_pmd_table.
+ */
+static inline int pud_none(pud_t pud)
+{
+	return pud_val(pud) == (unsigned long) invalid_pmd_table;
+}
+
+static inline int pud_bad(pud_t pud)
+{
+	return pud_val(pud) & ~PAGE_MASK;
+}
+
+static inline int pud_present(pud_t pud)
+{
+	return pud_val(pud) != (unsigned long) invalid_pmd_table;
+}
+
+static inline void pud_clear(pud_t *pudp)
+{
+	pud_val(*pudp) = ((unsigned long) invalid_pmd_table);
+}
+#endif
+
+#define pte_page(x)		pfn_to_page(pte_pfn(x))
+
+#define pte_pfn(x)		((unsigned long)((x).pte >> _PFN_SHIFT))
+#define pfn_pte(pfn, prot)	__pte(((pfn) << _PFN_SHIFT) | pgprot_val(prot))
+#define pfn_pmd(pfn, prot)	__pmd(((pfn) << _PFN_SHIFT) | pgprot_val(prot))
+
+#ifndef __PAGETABLE_PMD_FOLDED
+static inline pmd_t *pud_pgtable(pud_t pud)
+{
+	return (pmd_t *)pud_val(pud);
+}
+#define pud_phys(pud)		virt_to_phys((void *)pud_val(pud))
+#define pud_page(pud)		(pfn_to_page(pud_phys(pud) >> PAGE_SHIFT))
+
+#endif
+
+/*
+ * Initialize a new pgd / pmd table with invalid pointers.
+ */
+extern void pgd_init(unsigned long page);
+extern void pud_init(unsigned long page, unsigned long pagetable);
+extern void pmd_init(unsigned long page, unsigned long pagetable);
+
+/*
+ * Non-present pages:  high 40 bits are offset, next 8 bits type,
+ * low 16 bits zero.
+ */
+static inline pte_t mk_swap_pte(unsigned long type, unsigned long offset)
+{ pte_t pte; pte_val(pte) = (type << 16) | (offset << 24); return pte; }
+
+#define __swp_type(x)		(((x).val >> 16) & 0xff)
+#define __swp_offset(x)		((x).val >> 24)
+#define __swp_entry(type, offset) ((swp_entry_t) { pte_val(mk_swap_pte((type), (offset))) })
+#define __pte_to_swp_entry(pte) ((swp_entry_t) { pte_val(pte) })
+#define __swp_entry_to_pte(x)	((pte_t) { (x).val })
+
+#endif /* _ASM_PGTABLE_64_H */
diff --git a/arch/mips/include/asm/pgtable-bits.h b/arch/mips/include/asm/pgtable-bits.h
new file mode 100644
index 000000000..2362842ee
--- /dev/null
+++ b/arch/mips/include/asm/pgtable-bits.h
@@ -0,0 +1,285 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994 - 2002 by Ralf Baechle
+ * Copyright (C) 1999, 2000, 2001 Silicon Graphics, Inc.
+ * Copyright (C) 2002  Maciej W. Rozycki
+ */
+#ifndef _ASM_PGTABLE_BITS_H
+#define _ASM_PGTABLE_BITS_H
+
+
+/*
+ * Note that we shift the lower 32bits of each EntryLo[01] entry
+ * 6 bits to the left. That way we can convert the PFN into the
+ * physical address by a single 'and' operation and gain 6 additional
+ * bits for storing information which isn't present in a normal
+ * MIPS page table.
+ *
+ * Similar to the Alpha port, we need to keep track of the ref
+ * and mod bits in software.  We have a software "yeah you can read
+ * from this page" bit, and a hardware one which actually lets the
+ * process read from the page.	On the same token we have a software
+ * writable bit and the real hardware one which actually lets the
+ * process write to the page, this keeps a mod bit via the hardware
+ * dirty bit.
+ *
+ * Certain revisions of the R4000 and R5000 have a bug where if a
+ * certain sequence occurs in the last 3 instructions of an executable
+ * page, and the following page is not mapped, the cpu can do
+ * unpredictable things.  The code (when it is written) to deal with
+ * this problem will be in the update_mmu_cache() code for the r4k.
+ */
+#if defined(CONFIG_XPA)
+
+/*
+ * Page table bit offsets used for 64 bit physical addressing on
+ * MIPS32r5 with XPA.
+ */
+enum pgtable_bits {
+	/* Used by TLB hardware (placed in EntryLo*) */
+	_PAGE_NO_EXEC_SHIFT,
+	_PAGE_NO_READ_SHIFT,
+	_PAGE_GLOBAL_SHIFT,
+	_PAGE_VALID_SHIFT,
+	_PAGE_DIRTY_SHIFT,
+	_CACHE_SHIFT,
+
+	/* Used only by software (masked out before writing EntryLo*) */
+	_PAGE_PRESENT_SHIFT = 24,
+	_PAGE_WRITE_SHIFT,
+	_PAGE_ACCESSED_SHIFT,
+	_PAGE_MODIFIED_SHIFT,
+#if defined(CONFIG_ARCH_HAS_PTE_SPECIAL)
+	_PAGE_SPECIAL_SHIFT,
+#endif
+#if defined(CONFIG_HAVE_ARCH_SOFT_DIRTY)
+	_PAGE_SOFT_DIRTY_SHIFT,
+#endif
+};
+
+/*
+ * Bits for extended EntryLo0/EntryLo1 registers
+ */
+#define _PFNX_MASK		0xffffff
+
+#elif defined(CONFIG_PHYS_ADDR_T_64BIT) && defined(CONFIG_CPU_MIPS32)
+
+/*
+ * Page table bit offsets used for 36 bit physical addressing on MIPS32,
+ * for example with Alchemy or Netlogic XLP/XLR.
+ */
+enum pgtable_bits {
+	/* Used by TLB hardware (placed in EntryLo*) */
+	_PAGE_GLOBAL_SHIFT,
+	_PAGE_VALID_SHIFT,
+	_PAGE_DIRTY_SHIFT,
+	_CACHE_SHIFT,
+
+	/* Used only by software (masked out before writing EntryLo*) */
+	_PAGE_PRESENT_SHIFT = _CACHE_SHIFT + 3,
+	_PAGE_NO_READ_SHIFT,
+	_PAGE_WRITE_SHIFT,
+	_PAGE_ACCESSED_SHIFT,
+	_PAGE_MODIFIED_SHIFT,
+#if defined(CONFIG_ARCH_HAS_PTE_SPECIAL)
+	_PAGE_SPECIAL_SHIFT,
+#endif
+#if defined(CONFIG_HAVE_ARCH_SOFT_DIRTY)
+	_PAGE_SOFT_DIRTY_SHIFT,
+#endif
+};
+
+#elif defined(CONFIG_CPU_R3K_TLB)
+
+/* Page table bits used for r3k systems */
+enum pgtable_bits {
+	/* Used only by software (writes to EntryLo ignored) */
+	_PAGE_PRESENT_SHIFT,
+	_PAGE_NO_READ_SHIFT,
+	_PAGE_WRITE_SHIFT,
+	_PAGE_ACCESSED_SHIFT,
+	_PAGE_MODIFIED_SHIFT,
+#if defined(CONFIG_ARCH_HAS_PTE_SPECIAL)
+	_PAGE_SPECIAL_SHIFT,
+#endif
+#if defined(CONFIG_HAVE_ARCH_SOFT_DIRTY)
+	_PAGE_SOFT_DIRTY_SHIFT,
+#endif
+
+	/* Used by TLB hardware (placed in EntryLo) */
+	_PAGE_GLOBAL_SHIFT = 8,
+	_PAGE_VALID_SHIFT,
+	_PAGE_DIRTY_SHIFT,
+	_CACHE_UNCACHED_SHIFT,
+};
+
+#else
+
+/* Page table bits used for r4k systems */
+enum pgtable_bits {
+	/* Used only by software (masked out before writing EntryLo*) */
+	_PAGE_PRESENT_SHIFT,
+#if !defined(CONFIG_CPU_HAS_RIXI)
+	_PAGE_NO_READ_SHIFT,
+#endif
+	_PAGE_WRITE_SHIFT,
+	_PAGE_ACCESSED_SHIFT,
+	_PAGE_MODIFIED_SHIFT,
+#if defined(CONFIG_MIPS_HUGE_TLB_SUPPORT)
+	_PAGE_HUGE_SHIFT,
+#endif
+#if defined(CONFIG_ARCH_HAS_PTE_SPECIAL)
+	_PAGE_SPECIAL_SHIFT,
+#endif
+#if defined(CONFIG_HAVE_ARCH_SOFT_DIRTY)
+	_PAGE_SOFT_DIRTY_SHIFT,
+#endif
+	/* Used by TLB hardware (placed in EntryLo*) */
+#if defined(CONFIG_CPU_HAS_RIXI)
+	_PAGE_NO_EXEC_SHIFT,
+	_PAGE_NO_READ_SHIFT,
+#endif
+	_PAGE_GLOBAL_SHIFT,
+	_PAGE_VALID_SHIFT,
+	_PAGE_DIRTY_SHIFT,
+	_CACHE_SHIFT,
+};
+
+#endif /* defined(CONFIG_PHYS_ADDR_T_64BIT && defined(CONFIG_CPU_MIPS32) */
+
+/* Used only by software */
+#define _PAGE_PRESENT		(1 << _PAGE_PRESENT_SHIFT)
+#define _PAGE_WRITE		(1 << _PAGE_WRITE_SHIFT)
+#define _PAGE_ACCESSED		(1 << _PAGE_ACCESSED_SHIFT)
+#define _PAGE_MODIFIED		(1 << _PAGE_MODIFIED_SHIFT)
+#if defined(CONFIG_MIPS_HUGE_TLB_SUPPORT)
+# define _PAGE_HUGE		(1 << _PAGE_HUGE_SHIFT)
+#endif
+#if defined(CONFIG_ARCH_HAS_PTE_SPECIAL)
+# define _PAGE_SPECIAL		(1 << _PAGE_SPECIAL_SHIFT)
+#else
+# define _PAGE_SPECIAL		0
+#endif
+#if defined(CONFIG_HAVE_ARCH_SOFT_DIRTY)
+# define _PAGE_SOFT_DIRTY	(1 << _PAGE_SOFT_DIRTY_SHIFT)
+#else
+# define _PAGE_SOFT_DIRTY	0
+#endif
+
+/* Used by TLB hardware (placed in EntryLo*) */
+#if defined(CONFIG_XPA)
+# define _PAGE_NO_EXEC		(1 << _PAGE_NO_EXEC_SHIFT)
+#elif defined(CONFIG_CPU_HAS_RIXI)
+# define _PAGE_NO_EXEC		(cpu_has_rixi ? (1 << _PAGE_NO_EXEC_SHIFT) : 0)
+#endif
+#define _PAGE_NO_READ		(1 << _PAGE_NO_READ_SHIFT)
+#define _PAGE_GLOBAL		(1 << _PAGE_GLOBAL_SHIFT)
+#define _PAGE_VALID		(1 << _PAGE_VALID_SHIFT)
+#define _PAGE_DIRTY		(1 << _PAGE_DIRTY_SHIFT)
+#if defined(CONFIG_CPU_R3K_TLB)
+# define _CACHE_UNCACHED	(1 << _CACHE_UNCACHED_SHIFT)
+# define _CACHE_MASK		_CACHE_UNCACHED
+# define _PFN_SHIFT		PAGE_SHIFT
+#else
+# define _CACHE_MASK		(7 << _CACHE_SHIFT)
+# define _PFN_SHIFT		(PAGE_SHIFT - 12 + _CACHE_SHIFT + 3)
+#endif
+
+#ifndef _PAGE_NO_EXEC
+#define _PAGE_NO_EXEC		0
+#endif
+
+#define _PAGE_SILENT_READ	_PAGE_VALID
+#define _PAGE_SILENT_WRITE	_PAGE_DIRTY
+
+#define _PFN_MASK		(~((1 << (_PFN_SHIFT)) - 1))
+
+/*
+ * The final layouts of the PTE bits are:
+ *
+ *   64-bit, R1 or earlier:     CCC D V G [S H] M A W R P
+ *   32-bit, R1 or earler:      CCC D V G M A W R P
+ *   64-bit, R2 or later:       CCC D V G RI/R XI [S H] M A W P
+ *   32-bit, R2 or later:       CCC D V G RI/R XI M A W P
+ */
+
+
+/*
+ * pte_to_entrylo converts a page table entry (PTE) into a Mips
+ * entrylo0/1 value.
+ */
+static inline uint64_t pte_to_entrylo(unsigned long pte_val)
+{
+#ifdef CONFIG_CPU_HAS_RIXI
+	if (cpu_has_rixi) {
+		int sa;
+#ifdef CONFIG_32BIT
+		sa = 31 - _PAGE_NO_READ_SHIFT;
+#else
+		sa = 63 - _PAGE_NO_READ_SHIFT;
+#endif
+		/*
+		 * C has no way to express that this is a DSRL
+		 * _PAGE_NO_EXEC_SHIFT followed by a ROTR 2.  Luckily
+		 * in the fast path this is done in assembly
+		 */
+		return (pte_val >> _PAGE_GLOBAL_SHIFT) |
+			((pte_val & (_PAGE_NO_EXEC | _PAGE_NO_READ)) << sa);
+	}
+#endif
+
+	return pte_val >> _PAGE_GLOBAL_SHIFT;
+}
+
+/*
+ * Cache attributes
+ */
+#if defined(CONFIG_CPU_R3K_TLB)
+
+#define _CACHE_CACHABLE_NONCOHERENT 0
+#define _CACHE_UNCACHED_ACCELERATED _CACHE_UNCACHED
+
+#elif defined(CONFIG_CPU_SB1)
+
+/* No penalty for being coherent on the SB1, so just
+   use it for "noncoherent" spaces, too.  Shouldn't hurt. */
+
+#define _CACHE_CACHABLE_NONCOHERENT (5<<_CACHE_SHIFT)
+
+#endif
+
+#ifndef _CACHE_CACHABLE_NO_WA
+#define _CACHE_CACHABLE_NO_WA		(0<<_CACHE_SHIFT)
+#endif
+#ifndef _CACHE_CACHABLE_WA
+#define _CACHE_CACHABLE_WA		(1<<_CACHE_SHIFT)
+#endif
+#ifndef _CACHE_UNCACHED
+#define _CACHE_UNCACHED			(2<<_CACHE_SHIFT)
+#endif
+#ifndef _CACHE_CACHABLE_NONCOHERENT
+#define _CACHE_CACHABLE_NONCOHERENT	(3<<_CACHE_SHIFT)
+#endif
+#ifndef _CACHE_CACHABLE_CE
+#define _CACHE_CACHABLE_CE		(4<<_CACHE_SHIFT)
+#endif
+#ifndef _CACHE_CACHABLE_COW
+#define _CACHE_CACHABLE_COW		(5<<_CACHE_SHIFT)
+#endif
+#ifndef _CACHE_CACHABLE_CUW
+#define _CACHE_CACHABLE_CUW		(6<<_CACHE_SHIFT)
+#endif
+#ifndef _CACHE_UNCACHED_ACCELERATED
+#define _CACHE_UNCACHED_ACCELERATED	(7<<_CACHE_SHIFT)
+#endif
+
+#define __READABLE	(_PAGE_SILENT_READ | _PAGE_ACCESSED)
+#define __WRITEABLE	(_PAGE_SILENT_WRITE | _PAGE_WRITE | _PAGE_MODIFIED)
+
+#define _PAGE_CHG_MASK	(_PAGE_ACCESSED | _PAGE_MODIFIED |	\
+			 _PAGE_SOFT_DIRTY | _PFN_MASK | _CACHE_MASK)
+
+#endif /* _ASM_PGTABLE_BITS_H */
diff --git a/arch/mips/include/asm/pgtable.h b/arch/mips/include/asm/pgtable.h
new file mode 100644
index 000000000..467862767
--- /dev/null
+++ b/arch/mips/include/asm/pgtable.h
@@ -0,0 +1,716 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003 Ralf Baechle
+ */
+#ifndef _ASM_PGTABLE_H
+#define _ASM_PGTABLE_H
+
+#include <linux/mm_types.h>
+#include <linux/mmzone.h>
+#ifdef CONFIG_32BIT
+#include <asm/pgtable-32.h>
+#endif
+#ifdef CONFIG_64BIT
+#include <asm/pgtable-64.h>
+#endif
+
+#include <asm/cmpxchg.h>
+#include <asm/io.h>
+#include <asm/pgtable-bits.h>
+#include <asm/cpu-features.h>
+
+struct mm_struct;
+struct vm_area_struct;
+
+#define PAGE_SHARED	vm_get_page_prot(VM_READ|VM_WRITE|VM_SHARED)
+
+#define PAGE_KERNEL	__pgprot(_PAGE_PRESENT | __READABLE | __WRITEABLE | \
+				 _PAGE_GLOBAL | _page_cachable_default)
+#define PAGE_KERNEL_NC	__pgprot(_PAGE_PRESENT | __READABLE | __WRITEABLE | \
+				 _PAGE_GLOBAL | _CACHE_CACHABLE_NONCOHERENT)
+#define PAGE_KERNEL_UNCACHED __pgprot(_PAGE_PRESENT | __READABLE | \
+			__WRITEABLE | _PAGE_GLOBAL | _CACHE_UNCACHED)
+
+/*
+ * If _PAGE_NO_EXEC is not defined, we can't do page protection for
+ * execute, and consider it to be the same as read. Also, write
+ * permissions imply read permissions. This is the closest we can get
+ * by reasonable means..
+ */
+
+extern unsigned long _page_cachable_default;
+extern void __update_cache(unsigned long address, pte_t pte);
+
+/*
+ * ZERO_PAGE is a global shared page that is always zero; used
+ * for zero-mapped memory areas etc..
+ */
+
+extern unsigned long empty_zero_page;
+extern unsigned long zero_page_mask;
+
+#define ZERO_PAGE(vaddr) \
+	(virt_to_page((void *)(empty_zero_page + (((unsigned long)(vaddr)) & zero_page_mask))))
+#define __HAVE_COLOR_ZERO_PAGE
+
+extern void paging_init(void);
+
+/*
+ * Conversion functions: convert a page and protection to a page entry,
+ * and a page entry and page directory to the page they refer to.
+ */
+#define pmd_phys(pmd)		virt_to_phys((void *)pmd_val(pmd))
+
+static inline unsigned long pmd_pfn(pmd_t pmd)
+{
+	return pmd_val(pmd) >> _PFN_SHIFT;
+}
+
+#ifndef CONFIG_MIPS_HUGE_TLB_SUPPORT
+#define pmd_page(pmd)		(pfn_to_page(pmd_phys(pmd) >> PAGE_SHIFT))
+#endif /* CONFIG_MIPS_HUGE_TLB_SUPPORT */
+
+#define pmd_page_vaddr(pmd)	pmd_val(pmd)
+
+#define htw_stop()							\
+do {									\
+	unsigned long __flags;						\
+									\
+	if (cpu_has_htw) {						\
+		local_irq_save(__flags);				\
+		if(!raw_current_cpu_data.htw_seq++) {			\
+			write_c0_pwctl(read_c0_pwctl() &		\
+				       ~(1 << MIPS_PWCTL_PWEN_SHIFT));	\
+			back_to_back_c0_hazard();			\
+		}							\
+		local_irq_restore(__flags);				\
+	}								\
+} while(0)
+
+#define htw_start()							\
+do {									\
+	unsigned long __flags;						\
+									\
+	if (cpu_has_htw) {						\
+		local_irq_save(__flags);				\
+		if (!--raw_current_cpu_data.htw_seq) {			\
+			write_c0_pwctl(read_c0_pwctl() |		\
+				       (1 << MIPS_PWCTL_PWEN_SHIFT));	\
+			back_to_back_c0_hazard();			\
+		}							\
+		local_irq_restore(__flags);				\
+	}								\
+} while(0)
+
+static inline void set_pte_at(struct mm_struct *mm, unsigned long addr,
+			      pte_t *ptep, pte_t pteval);
+
+#if defined(CONFIG_PHYS_ADDR_T_64BIT) && defined(CONFIG_CPU_MIPS32)
+
+#ifdef CONFIG_XPA
+# define pte_none(pte)		(!(((pte).pte_high) & ~_PAGE_GLOBAL))
+#else
+# define pte_none(pte)		(!(((pte).pte_low | (pte).pte_high) & ~_PAGE_GLOBAL))
+#endif
+
+#define pte_present(pte)	((pte).pte_low & _PAGE_PRESENT)
+#define pte_no_exec(pte)	((pte).pte_low & _PAGE_NO_EXEC)
+
+static inline void set_pte(pte_t *ptep, pte_t pte)
+{
+	ptep->pte_high = pte.pte_high;
+	smp_wmb();
+	ptep->pte_low = pte.pte_low;
+
+#ifdef CONFIG_XPA
+	if (pte.pte_high & _PAGE_GLOBAL) {
+#else
+	if (pte.pte_low & _PAGE_GLOBAL) {
+#endif
+		pte_t *buddy = ptep_buddy(ptep);
+		/*
+		 * Make sure the buddy is global too (if it's !none,
+		 * it better already be global)
+		 */
+		if (pte_none(*buddy)) {
+			if (!IS_ENABLED(CONFIG_XPA))
+				buddy->pte_low |= _PAGE_GLOBAL;
+			buddy->pte_high |= _PAGE_GLOBAL;
+		}
+	}
+}
+
+static inline void pte_clear(struct mm_struct *mm, unsigned long addr, pte_t *ptep)
+{
+	pte_t null = __pte(0);
+
+	htw_stop();
+	/* Preserve global status for the pair */
+	if (IS_ENABLED(CONFIG_XPA)) {
+		if (ptep_buddy(ptep)->pte_high & _PAGE_GLOBAL)
+			null.pte_high = _PAGE_GLOBAL;
+	} else {
+		if (ptep_buddy(ptep)->pte_low & _PAGE_GLOBAL)
+			null.pte_low = null.pte_high = _PAGE_GLOBAL;
+	}
+
+	set_pte_at(mm, addr, ptep, null);
+	htw_start();
+}
+#else
+
+#define pte_none(pte)		(!(pte_val(pte) & ~_PAGE_GLOBAL))
+#define pte_present(pte)	(pte_val(pte) & _PAGE_PRESENT)
+#define pte_no_exec(pte)	(pte_val(pte) & _PAGE_NO_EXEC)
+
+/*
+ * Certain architectures need to do special things when pte's
+ * within a page table are directly modified.  Thus, the following
+ * hook is made available.
+ */
+static inline void set_pte(pte_t *ptep, pte_t pteval)
+{
+	*ptep = pteval;
+#if !defined(CONFIG_CPU_R3K_TLB)
+	if (pte_val(pteval) & _PAGE_GLOBAL) {
+		pte_t *buddy = ptep_buddy(ptep);
+		/*
+		 * Make sure the buddy is global too (if it's !none,
+		 * it better already be global)
+		 */
+# if defined(CONFIG_PHYS_ADDR_T_64BIT) && !defined(CONFIG_CPU_MIPS32)
+		cmpxchg64(&buddy->pte, 0, _PAGE_GLOBAL);
+# else
+		cmpxchg(&buddy->pte, 0, _PAGE_GLOBAL);
+# endif
+	}
+#endif
+}
+
+static inline void pte_clear(struct mm_struct *mm, unsigned long addr, pte_t *ptep)
+{
+	htw_stop();
+#if !defined(CONFIG_CPU_R3K_TLB)
+	/* Preserve global status for the pair */
+	if (pte_val(*ptep_buddy(ptep)) & _PAGE_GLOBAL)
+		set_pte_at(mm, addr, ptep, __pte(_PAGE_GLOBAL));
+	else
+#endif
+		set_pte_at(mm, addr, ptep, __pte(0));
+	htw_start();
+}
+#endif
+
+static inline void set_pte_at(struct mm_struct *mm, unsigned long addr,
+			      pte_t *ptep, pte_t pteval)
+{
+
+	if (!pte_present(pteval))
+		goto cache_sync_done;
+
+	if (pte_present(*ptep) && (pte_pfn(*ptep) == pte_pfn(pteval)))
+		goto cache_sync_done;
+
+	__update_cache(addr, pteval);
+cache_sync_done:
+	set_pte(ptep, pteval);
+}
+
+/*
+ * (pmds are folded into puds so this doesn't get actually called,
+ * but the define is needed for a generic inline function.)
+ */
+#define set_pmd(pmdptr, pmdval) do { *(pmdptr) = (pmdval); } while(0)
+
+#ifndef __PAGETABLE_PMD_FOLDED
+/*
+ * (puds are folded into pgds so this doesn't get actually called,
+ * but the define is needed for a generic inline function.)
+ */
+#define set_pud(pudptr, pudval) do { *(pudptr) = (pudval); } while(0)
+#endif
+
+#define PGD_T_LOG2	(__builtin_ffs(sizeof(pgd_t)) - 1)
+#define PMD_T_LOG2	(__builtin_ffs(sizeof(pmd_t)) - 1)
+#define PTE_T_LOG2	(__builtin_ffs(sizeof(pte_t)) - 1)
+
+/*
+ * We used to declare this array with size but gcc 3.3 and older are not able
+ * to find that this expression is a constant, so the size is dropped.
+ */
+extern pgd_t swapper_pg_dir[];
+
+/*
+ * Platform specific pte_special() and pte_mkspecial() definitions
+ * are required only when ARCH_HAS_PTE_SPECIAL is enabled.
+ */
+#if defined(CONFIG_ARCH_HAS_PTE_SPECIAL)
+#if defined(CONFIG_PHYS_ADDR_T_64BIT) && defined(CONFIG_CPU_MIPS32)
+static inline int pte_special(pte_t pte)
+{
+	return pte.pte_low & _PAGE_SPECIAL;
+}
+
+static inline pte_t pte_mkspecial(pte_t pte)
+{
+	pte.pte_low |= _PAGE_SPECIAL;
+	return pte;
+}
+#else
+static inline int pte_special(pte_t pte)
+{
+	return pte_val(pte) & _PAGE_SPECIAL;
+}
+
+static inline pte_t pte_mkspecial(pte_t pte)
+{
+	pte_val(pte) |= _PAGE_SPECIAL;
+	return pte;
+}
+#endif
+#endif /* CONFIG_ARCH_HAS_PTE_SPECIAL */
+
+/*
+ * The following only work if pte_present() is true.
+ * Undefined behaviour if not..
+ */
+#if defined(CONFIG_PHYS_ADDR_T_64BIT) && defined(CONFIG_CPU_MIPS32)
+static inline int pte_write(pte_t pte)	{ return pte.pte_low & _PAGE_WRITE; }
+static inline int pte_dirty(pte_t pte)	{ return pte.pte_low & _PAGE_MODIFIED; }
+static inline int pte_young(pte_t pte)	{ return pte.pte_low & _PAGE_ACCESSED; }
+
+static inline pte_t pte_wrprotect(pte_t pte)
+{
+	pte.pte_low  &= ~_PAGE_WRITE;
+	if (!IS_ENABLED(CONFIG_XPA))
+		pte.pte_low &= ~_PAGE_SILENT_WRITE;
+	pte.pte_high &= ~_PAGE_SILENT_WRITE;
+	return pte;
+}
+
+static inline pte_t pte_mkclean(pte_t pte)
+{
+	pte.pte_low  &= ~_PAGE_MODIFIED;
+	if (!IS_ENABLED(CONFIG_XPA))
+		pte.pte_low &= ~_PAGE_SILENT_WRITE;
+	pte.pte_high &= ~_PAGE_SILENT_WRITE;
+	return pte;
+}
+
+static inline pte_t pte_mkold(pte_t pte)
+{
+	pte.pte_low  &= ~_PAGE_ACCESSED;
+	if (!IS_ENABLED(CONFIG_XPA))
+		pte.pte_low &= ~_PAGE_SILENT_READ;
+	pte.pte_high &= ~_PAGE_SILENT_READ;
+	return pte;
+}
+
+static inline pte_t pte_mkwrite(pte_t pte)
+{
+	pte.pte_low |= _PAGE_WRITE;
+	if (pte.pte_low & _PAGE_MODIFIED) {
+		if (!IS_ENABLED(CONFIG_XPA))
+			pte.pte_low |= _PAGE_SILENT_WRITE;
+		pte.pte_high |= _PAGE_SILENT_WRITE;
+	}
+	return pte;
+}
+
+static inline pte_t pte_mkdirty(pte_t pte)
+{
+	pte.pte_low |= _PAGE_MODIFIED;
+	if (pte.pte_low & _PAGE_WRITE) {
+		if (!IS_ENABLED(CONFIG_XPA))
+			pte.pte_low |= _PAGE_SILENT_WRITE;
+		pte.pte_high |= _PAGE_SILENT_WRITE;
+	}
+	return pte;
+}
+
+static inline pte_t pte_mkyoung(pte_t pte)
+{
+	pte.pte_low |= _PAGE_ACCESSED;
+	if (!(pte.pte_low & _PAGE_NO_READ)) {
+		if (!IS_ENABLED(CONFIG_XPA))
+			pte.pte_low |= _PAGE_SILENT_READ;
+		pte.pte_high |= _PAGE_SILENT_READ;
+	}
+	return pte;
+}
+#else
+static inline int pte_write(pte_t pte)	{ return pte_val(pte) & _PAGE_WRITE; }
+static inline int pte_dirty(pte_t pte)	{ return pte_val(pte) & _PAGE_MODIFIED; }
+static inline int pte_young(pte_t pte)	{ return pte_val(pte) & _PAGE_ACCESSED; }
+
+static inline pte_t pte_wrprotect(pte_t pte)
+{
+	pte_val(pte) &= ~(_PAGE_WRITE | _PAGE_SILENT_WRITE);
+	return pte;
+}
+
+static inline pte_t pte_mkclean(pte_t pte)
+{
+	pte_val(pte) &= ~(_PAGE_MODIFIED | _PAGE_SILENT_WRITE);
+	return pte;
+}
+
+static inline pte_t pte_mkold(pte_t pte)
+{
+	pte_val(pte) &= ~(_PAGE_ACCESSED | _PAGE_SILENT_READ);
+	return pte;
+}
+
+static inline pte_t pte_mkwrite(pte_t pte)
+{
+	pte_val(pte) |= _PAGE_WRITE;
+	if (pte_val(pte) & _PAGE_MODIFIED)
+		pte_val(pte) |= _PAGE_SILENT_WRITE;
+	return pte;
+}
+
+static inline pte_t pte_mkdirty(pte_t pte)
+{
+	pte_val(pte) |= _PAGE_MODIFIED | _PAGE_SOFT_DIRTY;
+	if (pte_val(pte) & _PAGE_WRITE)
+		pte_val(pte) |= _PAGE_SILENT_WRITE;
+	return pte;
+}
+
+static inline pte_t pte_mkyoung(pte_t pte)
+{
+	pte_val(pte) |= _PAGE_ACCESSED;
+	if (!(pte_val(pte) & _PAGE_NO_READ))
+		pte_val(pte) |= _PAGE_SILENT_READ;
+	return pte;
+}
+
+#define pte_sw_mkyoung	pte_mkyoung
+
+#ifdef CONFIG_MIPS_HUGE_TLB_SUPPORT
+static inline int pte_huge(pte_t pte)	{ return pte_val(pte) & _PAGE_HUGE; }
+
+static inline pte_t pte_mkhuge(pte_t pte)
+{
+	pte_val(pte) |= _PAGE_HUGE;
+	return pte;
+}
+
+#define pmd_write pmd_write
+static inline int pmd_write(pmd_t pmd)
+{
+	return !!(pmd_val(pmd) & _PAGE_WRITE);
+}
+
+static inline struct page *pmd_page(pmd_t pmd)
+{
+	if (pmd_val(pmd) & _PAGE_HUGE)
+		return pfn_to_page(pmd_pfn(pmd));
+
+	return pfn_to_page(pmd_phys(pmd) >> PAGE_SHIFT);
+}
+#endif /* CONFIG_MIPS_HUGE_TLB_SUPPORT */
+
+#ifdef CONFIG_HAVE_ARCH_SOFT_DIRTY
+static inline bool pte_soft_dirty(pte_t pte)
+{
+	return pte_val(pte) & _PAGE_SOFT_DIRTY;
+}
+#define pte_swp_soft_dirty pte_soft_dirty
+
+static inline pte_t pte_mksoft_dirty(pte_t pte)
+{
+	pte_val(pte) |= _PAGE_SOFT_DIRTY;
+	return pte;
+}
+#define pte_swp_mksoft_dirty pte_mksoft_dirty
+
+static inline pte_t pte_clear_soft_dirty(pte_t pte)
+{
+	pte_val(pte) &= ~(_PAGE_SOFT_DIRTY);
+	return pte;
+}
+#define pte_swp_clear_soft_dirty pte_clear_soft_dirty
+
+#endif /* CONFIG_HAVE_ARCH_SOFT_DIRTY */
+
+#endif
+
+/*
+ * Macro to make mark a page protection value as "uncacheable".	 Note
+ * that "protection" is really a misnomer here as the protection value
+ * contains the memory attribute bits, dirty bits, and various other
+ * bits as well.
+ */
+#define pgprot_noncached pgprot_noncached
+
+static inline pgprot_t pgprot_noncached(pgprot_t _prot)
+{
+	unsigned long prot = pgprot_val(_prot);
+
+	prot = (prot & ~_CACHE_MASK) | _CACHE_UNCACHED;
+
+	return __pgprot(prot);
+}
+
+#define pgprot_writecombine pgprot_writecombine
+
+static inline pgprot_t pgprot_writecombine(pgprot_t _prot)
+{
+	unsigned long prot = pgprot_val(_prot);
+
+	/* cpu_data[0].writecombine is already shifted by _CACHE_SHIFT */
+	prot = (prot & ~_CACHE_MASK) | cpu_data[0].writecombine;
+
+	return __pgprot(prot);
+}
+
+static inline void flush_tlb_fix_spurious_fault(struct vm_area_struct *vma,
+						unsigned long address)
+{
+}
+
+#define __HAVE_ARCH_PTE_SAME
+static inline int pte_same(pte_t pte_a, pte_t pte_b)
+{
+	return pte_val(pte_a) == pte_val(pte_b);
+}
+
+#define __HAVE_ARCH_PTEP_SET_ACCESS_FLAGS
+static inline int ptep_set_access_flags(struct vm_area_struct *vma,
+					unsigned long address, pte_t *ptep,
+					pte_t entry, int dirty)
+{
+	if (!pte_same(*ptep, entry))
+		set_pte_at(vma->vm_mm, address, ptep, entry);
+	/*
+	 * update_mmu_cache will unconditionally execute, handling both
+	 * the case that the PTE changed and the spurious fault case.
+	 */
+	return true;
+}
+
+/*
+ * Conversion functions: convert a page and protection to a page entry,
+ * and a page entry and page directory to the page they refer to.
+ */
+#define mk_pte(page, pgprot)	pfn_pte(page_to_pfn(page), (pgprot))
+
+#if defined(CONFIG_XPA)
+static inline pte_t pte_modify(pte_t pte, pgprot_t newprot)
+{
+	pte.pte_low  &= (_PAGE_MODIFIED | _PAGE_ACCESSED | _PFNX_MASK);
+	pte.pte_high &= (_PFN_MASK | _CACHE_MASK);
+	pte.pte_low  |= pgprot_val(newprot) & ~_PFNX_MASK;
+	pte.pte_high |= pgprot_val(newprot) & ~(_PFN_MASK | _CACHE_MASK);
+	return pte;
+}
+#elif defined(CONFIG_PHYS_ADDR_T_64BIT) && defined(CONFIG_CPU_MIPS32)
+static inline pte_t pte_modify(pte_t pte, pgprot_t newprot)
+{
+	pte.pte_low  &= _PAGE_CHG_MASK;
+	pte.pte_high &= (_PFN_MASK | _CACHE_MASK);
+	pte.pte_low  |= pgprot_val(newprot);
+	pte.pte_high |= pgprot_val(newprot) & ~(_PFN_MASK | _CACHE_MASK);
+	return pte;
+}
+#else
+static inline pte_t pte_modify(pte_t pte, pgprot_t newprot)
+{
+	pte_val(pte) &= _PAGE_CHG_MASK;
+	pte_val(pte) |= pgprot_val(newprot) & ~_PAGE_CHG_MASK;
+	if ((pte_val(pte) & _PAGE_ACCESSED) && !(pte_val(pte) & _PAGE_NO_READ))
+		pte_val(pte) |= _PAGE_SILENT_READ;
+	return pte;
+}
+#endif
+
+
+extern void __update_tlb(struct vm_area_struct *vma, unsigned long address,
+	pte_t pte);
+
+static inline void update_mmu_cache(struct vm_area_struct *vma,
+	unsigned long address, pte_t *ptep)
+{
+	pte_t pte = *ptep;
+	__update_tlb(vma, address, pte);
+}
+
+#define	__HAVE_ARCH_UPDATE_MMU_TLB
+#define update_mmu_tlb	update_mmu_cache
+
+static inline void update_mmu_cache_pmd(struct vm_area_struct *vma,
+	unsigned long address, pmd_t *pmdp)
+{
+	pte_t pte = *(pte_t *)pmdp;
+
+	__update_tlb(vma, address, pte);
+}
+
+#define kern_addr_valid(addr)	(1)
+
+/*
+ * Allow physical addresses to be fixed up to help 36-bit peripherals.
+ */
+#ifdef CONFIG_MIPS_FIXUP_BIGPHYS_ADDR
+phys_addr_t fixup_bigphys_addr(phys_addr_t addr, phys_addr_t size);
+int io_remap_pfn_range(struct vm_area_struct *vma, unsigned long vaddr,
+		unsigned long pfn, unsigned long size, pgprot_t prot);
+#define io_remap_pfn_range io_remap_pfn_range
+#else
+#define fixup_bigphys_addr(addr, size)	(addr)
+#endif /* CONFIG_MIPS_FIXUP_BIGPHYS_ADDR */
+
+#ifdef CONFIG_TRANSPARENT_HUGEPAGE
+
+/* We don't have hardware dirty/accessed bits, generic_pmdp_establish is fine.*/
+#define pmdp_establish generic_pmdp_establish
+
+#define has_transparent_hugepage has_transparent_hugepage
+extern int has_transparent_hugepage(void);
+
+static inline int pmd_trans_huge(pmd_t pmd)
+{
+	return !!(pmd_val(pmd) & _PAGE_HUGE);
+}
+
+static inline pmd_t pmd_mkhuge(pmd_t pmd)
+{
+	pmd_val(pmd) |= _PAGE_HUGE;
+
+	return pmd;
+}
+
+extern void set_pmd_at(struct mm_struct *mm, unsigned long addr,
+		       pmd_t *pmdp, pmd_t pmd);
+
+static inline pmd_t pmd_wrprotect(pmd_t pmd)
+{
+	pmd_val(pmd) &= ~(_PAGE_WRITE | _PAGE_SILENT_WRITE);
+	return pmd;
+}
+
+static inline pmd_t pmd_mkwrite(pmd_t pmd)
+{
+	pmd_val(pmd) |= _PAGE_WRITE;
+	if (pmd_val(pmd) & _PAGE_MODIFIED)
+		pmd_val(pmd) |= _PAGE_SILENT_WRITE;
+
+	return pmd;
+}
+
+static inline int pmd_dirty(pmd_t pmd)
+{
+	return !!(pmd_val(pmd) & _PAGE_MODIFIED);
+}
+
+static inline pmd_t pmd_mkclean(pmd_t pmd)
+{
+	pmd_val(pmd) &= ~(_PAGE_MODIFIED | _PAGE_SILENT_WRITE);
+	return pmd;
+}
+
+static inline pmd_t pmd_mkdirty(pmd_t pmd)
+{
+	pmd_val(pmd) |= _PAGE_MODIFIED | _PAGE_SOFT_DIRTY;
+	if (pmd_val(pmd) & _PAGE_WRITE)
+		pmd_val(pmd) |= _PAGE_SILENT_WRITE;
+
+	return pmd;
+}
+
+#define pmd_young pmd_young
+static inline int pmd_young(pmd_t pmd)
+{
+	return !!(pmd_val(pmd) & _PAGE_ACCESSED);
+}
+
+static inline pmd_t pmd_mkold(pmd_t pmd)
+{
+	pmd_val(pmd) &= ~(_PAGE_ACCESSED|_PAGE_SILENT_READ);
+
+	return pmd;
+}
+
+static inline pmd_t pmd_mkyoung(pmd_t pmd)
+{
+	pmd_val(pmd) |= _PAGE_ACCESSED;
+
+	if (!(pmd_val(pmd) & _PAGE_NO_READ))
+		pmd_val(pmd) |= _PAGE_SILENT_READ;
+
+	return pmd;
+}
+
+#ifdef CONFIG_HAVE_ARCH_SOFT_DIRTY
+static inline int pmd_soft_dirty(pmd_t pmd)
+{
+	return !!(pmd_val(pmd) & _PAGE_SOFT_DIRTY);
+}
+
+static inline pmd_t pmd_mksoft_dirty(pmd_t pmd)
+{
+	pmd_val(pmd) |= _PAGE_SOFT_DIRTY;
+	return pmd;
+}
+
+static inline pmd_t pmd_clear_soft_dirty(pmd_t pmd)
+{
+	pmd_val(pmd) &= ~(_PAGE_SOFT_DIRTY);
+	return pmd;
+}
+
+#endif /* CONFIG_HAVE_ARCH_SOFT_DIRTY */
+
+/* Extern to avoid header file madness */
+extern pmd_t mk_pmd(struct page *page, pgprot_t prot);
+
+static inline pmd_t pmd_modify(pmd_t pmd, pgprot_t newprot)
+{
+	pmd_val(pmd) = (pmd_val(pmd) & (_PAGE_CHG_MASK | _PAGE_HUGE)) |
+		       (pgprot_val(newprot) & ~_PAGE_CHG_MASK);
+	return pmd;
+}
+
+static inline pmd_t pmd_mkinvalid(pmd_t pmd)
+{
+	pmd_val(pmd) &= ~(_PAGE_PRESENT | _PAGE_VALID | _PAGE_DIRTY);
+
+	return pmd;
+}
+
+/*
+ * The generic version pmdp_huge_get_and_clear uses a version of pmd_clear() with a
+ * different prototype.
+ */
+#define __HAVE_ARCH_PMDP_HUGE_GET_AND_CLEAR
+static inline pmd_t pmdp_huge_get_and_clear(struct mm_struct *mm,
+					    unsigned long address, pmd_t *pmdp)
+{
+	pmd_t old = *pmdp;
+
+	pmd_clear(pmdp);
+
+	return old;
+}
+
+#endif /* CONFIG_TRANSPARENT_HUGEPAGE */
+
+#ifdef _PAGE_HUGE
+#define pmd_leaf(pmd)	((pmd_val(pmd) & _PAGE_HUGE) != 0)
+#define pud_leaf(pud)	((pud_val(pud) & _PAGE_HUGE) != 0)
+#endif
+
+#define gup_fast_permitted(start, end)	(!cpu_has_dc_aliases)
+
+/*
+ * We provide our own get_unmapped area to cope with the virtual aliasing
+ * constraints placed on us by the cache architecture.
+ */
+#define HAVE_ARCH_UNMAPPED_AREA
+#define HAVE_ARCH_UNMAPPED_AREA_TOPDOWN
+
+#endif /* _ASM_PGTABLE_H */
diff --git a/arch/mips/include/asm/pm-cps.h b/arch/mips/include/asm/pm-cps.h
new file mode 100644
index 000000000..efd96e919
--- /dev/null
+++ b/arch/mips/include/asm/pm-cps.h
@@ -0,0 +1,49 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2014 Imagination Technologies
+ * Author: Paul Burton <paul.burton@mips.com>
+ */
+
+#ifndef __MIPS_ASM_PM_CPS_H__
+#define __MIPS_ASM_PM_CPS_H__
+
+/*
+ * The CM & CPC can only handle coherence & power control on a per-core basis,
+ * thus in an MT system the VP(E)s within each core are coupled and can only
+ * enter or exit states requiring CM or CPC assistance in unison.
+ */
+#if defined(CONFIG_CPU_MIPSR6)
+# define coupled_coherence cpu_has_vp
+#elif defined(CONFIG_MIPS_MT)
+# define coupled_coherence cpu_has_mipsmt
+#else
+# define coupled_coherence 0
+#endif
+
+/* Enumeration of possible PM states */
+enum cps_pm_state {
+	CPS_PM_NC_WAIT,		/* MIPS wait instruction, non-coherent */
+	CPS_PM_CLOCK_GATED,	/* Core clock gated */
+	CPS_PM_POWER_GATED,	/* Core power gated */
+	CPS_PM_STATE_COUNT,
+};
+
+/**
+ * cps_pm_support_state - determine whether the system supports a PM state
+ * @state: the state to test for support
+ *
+ * Returns true if the system supports the given state, otherwise false.
+ */
+extern bool cps_pm_support_state(enum cps_pm_state state);
+
+/**
+ * cps_pm_enter_state - enter a PM state
+ * @state: the state to enter
+ *
+ * Enter the given PM state. If coupled_coherence is non-zero then it is
+ * expected that this function be called at approximately the same time on
+ * each coupled CPU. Returns 0 on successful entry & exit, otherwise -errno.
+ */
+extern int cps_pm_enter_state(enum cps_pm_state state);
+
+#endif /* __MIPS_ASM_PM_CPS_H__ */
diff --git a/arch/mips/include/asm/pm.h b/arch/mips/include/asm/pm.h
new file mode 100644
index 000000000..10bb7b640
--- /dev/null
+++ b/arch/mips/include/asm/pm.h
@@ -0,0 +1,155 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2014 Imagination Technologies Ltd
+ *
+ * PM helper macros for CPU power off (e.g. Suspend-to-RAM).
+ */
+
+#ifndef __ASM_PM_H
+#define __ASM_PM_H
+
+#ifdef __ASSEMBLY__
+
+#include <asm/asm-offsets.h>
+#include <asm/asm.h>
+#include <asm/mipsregs.h>
+#include <asm/regdef.h>
+
+/* Save CPU state to stack for suspend to RAM */
+.macro SUSPEND_SAVE_REGS
+	subu	sp, PT_SIZE
+	/* Call preserved GPRs */
+	LONG_S	$16, PT_R16(sp)
+	LONG_S	$17, PT_R17(sp)
+	LONG_S	$18, PT_R18(sp)
+	LONG_S	$19, PT_R19(sp)
+	LONG_S	$20, PT_R20(sp)
+	LONG_S	$21, PT_R21(sp)
+	LONG_S	$22, PT_R22(sp)
+	LONG_S	$23, PT_R23(sp)
+	LONG_S	$28, PT_R28(sp)
+	LONG_S	$30, PT_R30(sp)
+	LONG_S	$31, PT_R31(sp)
+	/* A couple of CP0 registers with space in pt_regs */
+	mfc0	k0, CP0_STATUS
+	LONG_S	k0, PT_STATUS(sp)
+.endm
+
+/* Restore CPU state from stack after resume from RAM */
+.macro RESUME_RESTORE_REGS_RETURN
+	.set	push
+	.set	noreorder
+	/* A couple of CP0 registers with space in pt_regs */
+	LONG_L	k0, PT_STATUS(sp)
+	mtc0	k0, CP0_STATUS
+	/* Call preserved GPRs */
+	LONG_L	$16, PT_R16(sp)
+	LONG_L	$17, PT_R17(sp)
+	LONG_L	$18, PT_R18(sp)
+	LONG_L	$19, PT_R19(sp)
+	LONG_L	$20, PT_R20(sp)
+	LONG_L	$21, PT_R21(sp)
+	LONG_L	$22, PT_R22(sp)
+	LONG_L	$23, PT_R23(sp)
+	LONG_L	$28, PT_R28(sp)
+	LONG_L	$30, PT_R30(sp)
+	LONG_L	$31, PT_R31(sp)
+	/* Pop and return */
+	jr	ra
+	 addiu	sp, PT_SIZE
+	.set	pop
+.endm
+
+/* Get address of static suspend state into t1 */
+.macro LA_STATIC_SUSPEND
+	la	t1, mips_static_suspend_state
+.endm
+
+/* Save important CPU state for early restoration to global data */
+.macro SUSPEND_SAVE_STATIC
+#ifdef CONFIG_EVA
+	/*
+	 * Segment configuration is saved in global data where it can be easily
+	 * reloaded without depending on the segment configuration.
+	 */
+	mfc0	k0, CP0_PAGEMASK, 2	/* SegCtl0 */
+	LONG_S	k0, SSS_SEGCTL0(t1)
+	mfc0	k0, CP0_PAGEMASK, 3	/* SegCtl1 */
+	LONG_S	k0, SSS_SEGCTL1(t1)
+	mfc0	k0, CP0_PAGEMASK, 4	/* SegCtl2 */
+	LONG_S	k0, SSS_SEGCTL2(t1)
+#endif
+	/* save stack pointer (pointing to GPRs) */
+	LONG_S	sp, SSS_SP(t1)
+.endm
+
+/* Restore important CPU state early from global data */
+.macro RESUME_RESTORE_STATIC
+#ifdef CONFIG_EVA
+	/*
+	 * Segment configuration must be restored prior to any access to
+	 * allocated memory, as it may reside outside of the legacy kernel
+	 * segments.
+	 */
+	LONG_L	k0, SSS_SEGCTL0(t1)
+	mtc0	k0, CP0_PAGEMASK, 2	/* SegCtl0 */
+	LONG_L	k0, SSS_SEGCTL1(t1)
+	mtc0	k0, CP0_PAGEMASK, 3	/* SegCtl1 */
+	LONG_L	k0, SSS_SEGCTL2(t1)
+	mtc0	k0, CP0_PAGEMASK, 4	/* SegCtl2 */
+	tlbw_use_hazard
+#endif
+	/* restore stack pointer (pointing to GPRs) */
+	LONG_L	sp, SSS_SP(t1)
+.endm
+
+/* flush caches to make sure context has reached memory */
+.macro SUSPEND_CACHE_FLUSH
+	.extern	__wback_cache_all
+	.set	push
+	.set	noreorder
+	la	t1, __wback_cache_all
+	LONG_L	t0, 0(t1)
+	jalr	t0
+	 nop
+	.set	pop
+ .endm
+
+/* Save suspend state and flush data caches to RAM */
+.macro SUSPEND_SAVE
+	SUSPEND_SAVE_REGS
+	LA_STATIC_SUSPEND
+	SUSPEND_SAVE_STATIC
+	SUSPEND_CACHE_FLUSH
+.endm
+
+/* Restore saved state after resume from RAM and return */
+.macro RESUME_RESTORE_RETURN
+	LA_STATIC_SUSPEND
+	RESUME_RESTORE_STATIC
+	RESUME_RESTORE_REGS_RETURN
+.endm
+
+#else /* __ASSEMBLY__ */
+
+/**
+ * struct mips_static_suspend_state - Core saved CPU state across S2R.
+ * @segctl:	CP0 Segment control registers.
+ * @sp:		Stack frame where GP register context is saved.
+ *
+ * This structure contains minimal CPU state that must be saved in static kernel
+ * data in order to be able to restore the rest of the state. This includes
+ * segmentation configuration in the case of EVA being enabled, as they must be
+ * restored prior to any kmalloc'd memory being referenced (even the stack
+ * pointer).
+ */
+struct mips_static_suspend_state {
+#ifdef CONFIG_EVA
+	unsigned long segctl[3];
+#endif
+	unsigned long sp;
+};
+
+#endif /* !__ASSEMBLY__ */
+
+#endif /* __ASM_PM_HELPERS_H */
diff --git a/arch/mips/include/asm/prefetch.h b/arch/mips/include/asm/prefetch.h
new file mode 100644
index 000000000..a56594f36
--- /dev/null
+++ b/arch/mips/include/asm/prefetch.h
@@ -0,0 +1,87 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003 by Ralf Baechle
+ */
+#ifndef __ASM_PREFETCH_H
+#define __ASM_PREFETCH_H
+
+
+/*
+ * R5000 and RM5200 implements pref and prefx instructions but they're nops, so
+ * rather than wasting time we pretend these processors don't support
+ * prefetching at all.
+ *
+ * R5432 implements Load, Store, LoadStreamed, StoreStreamed, LoadRetained,
+ * StoreRetained and WriteBackInvalidate but not Pref_PrepareForStore.
+ *
+ * Hell (and the book on my shelf I can't open ...) know what the R8000 does.
+ *
+ * RM7000 version 1.0 interprets all hints as Pref_Load; version 2.0 implements
+ * Pref_PrepareForStore also.
+ *
+ * RM9000 is MIPS IV but implements prefetching like MIPS32/MIPS64; it's
+ * Pref_WriteBackInvalidate is a nop and Pref_PrepareForStore is broken in
+ * current versions due to erratum G105.
+ *
+ * VR5500 (including VR5701 and VR7701) only implement load prefetch.
+ *
+ * Finally MIPS32 and MIPS64 implement all of the following hints.
+ */
+
+#define Pref_Load			0
+#define Pref_Store			1
+						/* 2 and 3 are reserved */
+#define Pref_LoadStreamed		4
+#define Pref_StoreStreamed		5
+#define Pref_LoadRetained		6
+#define Pref_StoreRetained		7
+						/* 8 ... 24 are reserved */
+#define Pref_WriteBackInvalidate	25
+#define Pref_PrepareForStore		30
+
+#ifdef __ASSEMBLY__
+
+	.macro	__pref hint addr
+#ifdef CONFIG_CPU_HAS_PREFETCH
+	pref	\hint, \addr
+#endif
+	.endm
+
+	.macro	pref_load addr
+	__pref	Pref_Load, \addr
+	.endm
+
+	.macro	pref_store addr
+	__pref	Pref_Store, \addr
+	.endm
+
+	.macro	pref_load_streamed addr
+	__pref	Pref_LoadStreamed, \addr
+	.endm
+
+	.macro	pref_store_streamed addr
+	__pref	Pref_StoreStreamed, \addr
+	.endm
+
+	.macro	pref_load_retained addr
+	__pref	Pref_LoadRetained, \addr
+	.endm
+
+	.macro	pref_store_retained addr
+	__pref	Pref_StoreRetained, \addr
+	.endm
+
+	.macro	pref_wback_inv addr
+	__pref	Pref_WriteBackInvalidate, \addr
+	.endm
+
+	.macro	pref_prepare_for_store addr
+	__pref	Pref_PrepareForStore, \addr
+	.endm
+
+#endif
+
+#endif /* __ASM_PREFETCH_H */
diff --git a/arch/mips/include/asm/processor.h b/arch/mips/include/asm/processor.h
new file mode 100644
index 000000000..3fde1ff72
--- /dev/null
+++ b/arch/mips/include/asm/processor.h
@@ -0,0 +1,400 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994 Waldorf GMBH
+ * Copyright (C) 1995, 1996, 1997, 1998, 1999, 2001, 2002, 2003 Ralf Baechle
+ * Copyright (C) 1996 Paul M. Antoine
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_PROCESSOR_H
+#define _ASM_PROCESSOR_H
+
+#include <linux/atomic.h>
+#include <linux/cpumask.h>
+#include <linux/sizes.h>
+#include <linux/threads.h>
+
+#include <asm/cachectl.h>
+#include <asm/cpu.h>
+#include <asm/cpu-info.h>
+#include <asm/dsemul.h>
+#include <asm/mipsregs.h>
+#include <asm/prefetch.h>
+#include <asm/vdso/processor.h>
+
+/*
+ * System setup and hardware flags..
+ */
+
+extern unsigned int vced_count, vcei_count;
+extern int arch_dup_task_struct(struct task_struct *dst, struct task_struct *src);
+
+#ifdef CONFIG_32BIT
+/*
+ * User space process size: 2GB. This is hardcoded into a few places,
+ * so don't change it unless you know what you are doing.
+ */
+#define TASK_SIZE	0x80000000UL
+
+#define STACK_TOP_MAX	TASK_SIZE
+
+#define TASK_IS_32BIT_ADDR 1
+
+#endif
+
+#ifdef CONFIG_64BIT
+/*
+ * User space process size: 1TB. This is hardcoded into a few places,
+ * so don't change it unless you know what you are doing.  TASK_SIZE
+ * is limited to 1TB by the R4000 architecture; R10000 and better can
+ * support 16TB; the architectural reserve for future expansion is
+ * 8192EB ...
+ */
+#define TASK_SIZE32	0x7fff8000UL
+#ifdef CONFIG_MIPS_VA_BITS_48
+#define TASK_SIZE64     (0x1UL << ((cpu_data[0].vmbits>48)?48:cpu_data[0].vmbits))
+#else
+#define TASK_SIZE64     0x10000000000UL
+#endif
+#define TASK_SIZE (test_thread_flag(TIF_32BIT_ADDR) ? TASK_SIZE32 : TASK_SIZE64)
+#define STACK_TOP_MAX	TASK_SIZE64
+
+#define TASK_SIZE_OF(tsk)						\
+	(test_tsk_thread_flag(tsk, TIF_32BIT_ADDR) ? TASK_SIZE32 : TASK_SIZE64)
+
+#define TASK_IS_32BIT_ADDR test_thread_flag(TIF_32BIT_ADDR)
+
+#endif
+
+#define VDSO_RANDOMIZE_SIZE	(TASK_IS_32BIT_ADDR ? SZ_1M : SZ_64M)
+
+extern unsigned long mips_stack_top(void);
+#define STACK_TOP		mips_stack_top()
+
+/*
+ * This decides where the kernel will search for a free chunk of vm
+ * space during mmap's.
+ */
+#define TASK_UNMAPPED_BASE PAGE_ALIGN(TASK_SIZE / 3)
+
+
+#define NUM_FPU_REGS	32
+
+#ifdef CONFIG_CPU_HAS_MSA
+# define FPU_REG_WIDTH	128
+#else
+# define FPU_REG_WIDTH	64
+#endif
+
+union fpureg {
+	__u32	val32[FPU_REG_WIDTH / 32];
+	__u64	val64[FPU_REG_WIDTH / 64];
+};
+
+#ifdef CONFIG_CPU_LITTLE_ENDIAN
+# define FPR_IDX(width, idx)	(idx)
+#else
+# define FPR_IDX(width, idx)	((idx) ^ ((64 / (width)) - 1))
+#endif
+
+#define BUILD_FPR_ACCESS(width) \
+static inline u##width get_fpr##width(union fpureg *fpr, unsigned idx)	\
+{									\
+	return fpr->val##width[FPR_IDX(width, idx)];			\
+}									\
+									\
+static inline void set_fpr##width(union fpureg *fpr, unsigned idx,	\
+				  u##width val)				\
+{									\
+	fpr->val##width[FPR_IDX(width, idx)] = val;			\
+}
+
+BUILD_FPR_ACCESS(32)
+BUILD_FPR_ACCESS(64)
+
+/*
+ * It would be nice to add some more fields for emulator statistics,
+ * the additional information is private to the FPU emulator for now.
+ * See arch/mips/include/asm/fpu_emulator.h.
+ */
+
+struct mips_fpu_struct {
+	union fpureg	fpr[NUM_FPU_REGS];
+	unsigned int	fcr31;
+	unsigned int	msacsr;
+};
+
+#define NUM_DSP_REGS   6
+
+typedef unsigned long dspreg_t;
+
+struct mips_dsp_state {
+	dspreg_t	dspr[NUM_DSP_REGS];
+	unsigned int	dspcontrol;
+};
+
+#define INIT_CPUMASK { \
+	{0,} \
+}
+
+struct mips3264_watch_reg_state {
+	/* The width of watchlo is 32 in a 32 bit kernel and 64 in a
+	   64 bit kernel.  We use unsigned long as it has the same
+	   property. */
+	unsigned long watchlo[NUM_WATCH_REGS];
+	/* Only the mask and IRW bits from watchhi. */
+	u16 watchhi[NUM_WATCH_REGS];
+};
+
+union mips_watch_reg_state {
+	struct mips3264_watch_reg_state mips3264;
+};
+
+#if defined(CONFIG_CPU_CAVIUM_OCTEON)
+
+struct octeon_cop2_state {
+	/* DMFC2 rt, 0x0201 */
+	unsigned long	cop2_crc_iv;
+	/* DMFC2 rt, 0x0202 (Set with DMTC2 rt, 0x1202) */
+	unsigned long	cop2_crc_length;
+	/* DMFC2 rt, 0x0200 (set with DMTC2 rt, 0x4200) */
+	unsigned long	cop2_crc_poly;
+	/* DMFC2 rt, 0x0402; DMFC2 rt, 0x040A */
+	unsigned long	cop2_llm_dat[2];
+       /* DMFC2 rt, 0x0084 */
+	unsigned long	cop2_3des_iv;
+	/* DMFC2 rt, 0x0080; DMFC2 rt, 0x0081; DMFC2 rt, 0x0082 */
+	unsigned long	cop2_3des_key[3];
+	/* DMFC2 rt, 0x0088 (Set with DMTC2 rt, 0x0098) */
+	unsigned long	cop2_3des_result;
+	/* DMFC2 rt, 0x0111 (FIXME: Read Pass1 Errata) */
+	unsigned long	cop2_aes_inp0;
+	/* DMFC2 rt, 0x0102; DMFC2 rt, 0x0103 */
+	unsigned long	cop2_aes_iv[2];
+	/* DMFC2 rt, 0x0104; DMFC2 rt, 0x0105; DMFC2 rt, 0x0106; DMFC2
+	 * rt, 0x0107 */
+	unsigned long	cop2_aes_key[4];
+	/* DMFC2 rt, 0x0110 */
+	unsigned long	cop2_aes_keylen;
+	/* DMFC2 rt, 0x0100; DMFC2 rt, 0x0101 */
+	unsigned long	cop2_aes_result[2];
+	/* DMFC2 rt, 0x0240; DMFC2 rt, 0x0241; DMFC2 rt, 0x0242; DMFC2
+	 * rt, 0x0243; DMFC2 rt, 0x0244; DMFC2 rt, 0x0245; DMFC2 rt,
+	 * 0x0246; DMFC2 rt, 0x0247; DMFC2 rt, 0x0248; DMFC2 rt,
+	 * 0x0249; DMFC2 rt, 0x024A; DMFC2 rt, 0x024B; DMFC2 rt,
+	 * 0x024C; DMFC2 rt, 0x024D; DMFC2 rt, 0x024E - Pass2 */
+	unsigned long	cop2_hsh_datw[15];
+	/* DMFC2 rt, 0x0250; DMFC2 rt, 0x0251; DMFC2 rt, 0x0252; DMFC2
+	 * rt, 0x0253; DMFC2 rt, 0x0254; DMFC2 rt, 0x0255; DMFC2 rt,
+	 * 0x0256; DMFC2 rt, 0x0257 - Pass2 */
+	unsigned long	cop2_hsh_ivw[8];
+	/* DMFC2 rt, 0x0258; DMFC2 rt, 0x0259 - Pass2 */
+	unsigned long	cop2_gfm_mult[2];
+	/* DMFC2 rt, 0x025E - Pass2 */
+	unsigned long	cop2_gfm_poly;
+	/* DMFC2 rt, 0x025A; DMFC2 rt, 0x025B - Pass2 */
+	unsigned long	cop2_gfm_result[2];
+	/* DMFC2 rt, 0x24F, DMFC2 rt, 0x50, OCTEON III */
+	unsigned long	cop2_sha3[2];
+};
+#define COP2_INIT						\
+	.cp2			= {0,},
+
+struct octeon_cvmseg_state {
+	unsigned long cvmseg[CONFIG_CAVIUM_OCTEON_CVMSEG_SIZE]
+			    [cpu_dcache_line_size() / sizeof(unsigned long)];
+};
+
+#else
+#define COP2_INIT
+#endif
+
+#ifdef CONFIG_CPU_HAS_MSA
+# define ARCH_MIN_TASKALIGN	16
+# define FPU_ALIGN		__aligned(16)
+#else
+# define ARCH_MIN_TASKALIGN	8
+# define FPU_ALIGN
+#endif
+
+struct mips_abi;
+
+/*
+ * If you change thread_struct remember to change the #defines below too!
+ */
+struct thread_struct {
+	/* Saved main processor registers. */
+	unsigned long reg16;
+	unsigned long reg17, reg18, reg19, reg20, reg21, reg22, reg23;
+	unsigned long reg29, reg30, reg31;
+
+	/* Saved cp0 stuff. */
+	unsigned long cp0_status;
+
+#ifdef CONFIG_MIPS_FP_SUPPORT
+	/* Saved fpu/fpu emulator stuff. */
+	struct mips_fpu_struct fpu FPU_ALIGN;
+	/* Assigned branch delay slot 'emulation' frame */
+	atomic_t bd_emu_frame;
+	/* PC of the branch from a branch delay slot 'emulation' */
+	unsigned long bd_emu_branch_pc;
+	/* PC to continue from following a branch delay slot 'emulation' */
+	unsigned long bd_emu_cont_pc;
+#endif
+#ifdef CONFIG_MIPS_MT_FPAFF
+	/* Emulated instruction count */
+	unsigned long emulated_fp;
+	/* Saved per-thread scheduler affinity mask */
+	cpumask_t user_cpus_allowed;
+#endif /* CONFIG_MIPS_MT_FPAFF */
+
+	/* Saved state of the DSP ASE, if available. */
+	struct mips_dsp_state dsp;
+
+	/* Saved watch register state, if available. */
+	union mips_watch_reg_state watch;
+
+	/* Other stuff associated with the thread. */
+	unsigned long cp0_badvaddr;	/* Last user fault */
+	unsigned long cp0_baduaddr;	/* Last kernel fault accessing USEG */
+	unsigned long error_code;
+	unsigned long trap_nr;
+#ifdef CONFIG_CPU_CAVIUM_OCTEON
+	struct octeon_cop2_state cp2 __attribute__ ((__aligned__(128)));
+	struct octeon_cvmseg_state cvmseg __attribute__ ((__aligned__(128)));
+#endif
+	struct mips_abi *abi;
+};
+
+#ifdef CONFIG_MIPS_MT_FPAFF
+#define FPAFF_INIT						\
+	.emulated_fp			= 0,			\
+	.user_cpus_allowed		= INIT_CPUMASK,
+#else
+#define FPAFF_INIT
+#endif /* CONFIG_MIPS_MT_FPAFF */
+
+#ifdef CONFIG_MIPS_FP_SUPPORT
+# define FPU_INIT						\
+	.fpu			= {				\
+		.fpr		= {{{0,},},},			\
+		.fcr31		= 0,				\
+		.msacsr		= 0,				\
+	},							\
+	/* Delay slot emulation */				\
+	.bd_emu_frame = ATOMIC_INIT(BD_EMUFRAME_NONE),		\
+	.bd_emu_branch_pc = 0,					\
+	.bd_emu_cont_pc = 0,
+#else
+# define FPU_INIT
+#endif
+
+#define INIT_THREAD  {						\
+	/*							\
+	 * Saved main processor registers			\
+	 */							\
+	.reg16			= 0,				\
+	.reg17			= 0,				\
+	.reg18			= 0,				\
+	.reg19			= 0,				\
+	.reg20			= 0,				\
+	.reg21			= 0,				\
+	.reg22			= 0,				\
+	.reg23			= 0,				\
+	.reg29			= 0,				\
+	.reg30			= 0,				\
+	.reg31			= 0,				\
+	/*							\
+	 * Saved cp0 stuff					\
+	 */							\
+	.cp0_status		= 0,				\
+	/*							\
+	 * Saved FPU/FPU emulator stuff				\
+	 */							\
+	FPU_INIT						\
+	/*							\
+	 * FPU affinity state (null if not FPAFF)		\
+	 */							\
+	FPAFF_INIT						\
+	/*							\
+	 * Saved DSP stuff					\
+	 */							\
+	.dsp			= {				\
+		.dspr		= {0, },			\
+		.dspcontrol	= 0,				\
+	},							\
+	/*							\
+	 * saved watch register stuff				\
+	 */							\
+	.watch = {{{0,},},},					\
+	/*							\
+	 * Other stuff associated with the process		\
+	 */							\
+	.cp0_badvaddr		= 0,				\
+	.cp0_baduaddr		= 0,				\
+	.error_code		= 0,				\
+	.trap_nr		= 0,				\
+	/*							\
+	 * Platform specific cop2 registers(null if no COP2)	\
+	 */							\
+	COP2_INIT						\
+}
+
+struct task_struct;
+
+/*
+ * Do necessary setup to start up a newly executed thread.
+ */
+extern void start_thread(struct pt_regs * regs, unsigned long pc, unsigned long sp);
+
+static inline void flush_thread(void)
+{
+}
+
+unsigned long __get_wchan(struct task_struct *p);
+
+#define __KSTK_TOS(tsk) ((unsigned long)task_stack_page(tsk) + \
+			 THREAD_SIZE - 32 - sizeof(struct pt_regs))
+#define task_pt_regs(tsk) ((struct pt_regs *)__KSTK_TOS(tsk))
+#define KSTK_EIP(tsk) (task_pt_regs(tsk)->cp0_epc)
+#define KSTK_ESP(tsk) (task_pt_regs(tsk)->regs[29])
+#define KSTK_STATUS(tsk) (task_pt_regs(tsk)->cp0_status)
+
+/*
+ * Return_address is a replacement for __builtin_return_address(count)
+ * which on certain architectures cannot reasonably be implemented in GCC
+ * (MIPS, Alpha) or is unusable with -fomit-frame-pointer (i386).
+ * Note that __builtin_return_address(x>=1) is forbidden because GCC
+ * aborts compilation on some CPUs.  It's simply not possible to unwind
+ * some CPU's stackframes.
+ *
+ * __builtin_return_address works only for non-leaf functions.	We avoid the
+ * overhead of a function call by forcing the compiler to save the return
+ * address register on the stack.
+ */
+#define return_address() ({__asm__ __volatile__("":::"$31");__builtin_return_address(0);})
+
+#ifdef CONFIG_CPU_HAS_PREFETCH
+
+#define ARCH_HAS_PREFETCH
+#define prefetch(x) __builtin_prefetch((x), 0, 1)
+
+#define ARCH_HAS_PREFETCHW
+#define prefetchw(x) __builtin_prefetch((x), 1, 1)
+
+#endif
+
+/*
+ * Functions & macros implementing the PR_GET_FP_MODE & PR_SET_FP_MODE options
+ * to the prctl syscall.
+ */
+extern int mips_get_process_fp_mode(struct task_struct *task);
+extern int mips_set_process_fp_mode(struct task_struct *task,
+				    unsigned int value);
+
+#define GET_FP_MODE(task)		mips_get_process_fp_mode(task)
+#define SET_FP_MODE(task,value)		mips_set_process_fp_mode(task, value)
+
+#endif /* _ASM_PROCESSOR_H */
diff --git a/arch/mips/include/asm/prom.h b/arch/mips/include/asm/prom.h
new file mode 100644
index 000000000..2d7440608
--- /dev/null
+++ b/arch/mips/include/asm/prom.h
@@ -0,0 +1,30 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *  arch/mips/include/asm/prom.h
+ *
+ *  Copyright (C) 2010 Cisco Systems Inc. <dediao@cisco.com>
+ */
+#ifndef __ASM_PROM_H
+#define __ASM_PROM_H
+
+#ifdef CONFIG_USE_OF
+#include <linux/bug.h>
+#include <linux/io.h>
+#include <linux/types.h>
+#include <asm/bootinfo.h>
+
+extern void device_tree_init(void);
+
+struct boot_param_header;
+
+extern void __dt_setup_arch(void *bph);
+extern int __dt_register_buses(const char *bus0, const char *bus1);
+
+#else /* !CONFIG_USE_OF */
+static inline void device_tree_init(void) { }
+#endif /* !CONFIG_USE_OF */
+
+extern char *mips_get_machine_name(void);
+extern void mips_set_machine_name(const char *name);
+
+#endif /* __ASM_PROM_H */
diff --git a/arch/mips/include/asm/ptrace.h b/arch/mips/include/asm/ptrace.h
new file mode 100644
index 000000000..daf3cf244
--- /dev/null
+++ b/arch/mips/include/asm/ptrace.h
@@ -0,0 +1,189 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994, 95, 96, 97, 98, 99, 2000 by Ralf Baechle
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_PTRACE_H
+#define _ASM_PTRACE_H
+
+
+#include <linux/compiler.h>
+#include <linux/linkage.h>
+#include <linux/types.h>
+#include <asm/isadep.h>
+#include <asm/page.h>
+#include <asm/thread_info.h>
+#include <uapi/asm/ptrace.h>
+
+/*
+ * This struct defines the way the registers are stored on the stack during a
+ * system call/exception. As usual the registers k0/k1 aren't being saved.
+ *
+ * If you add a register here, also add it to regoffset_table[] in
+ * arch/mips/kernel/ptrace.c.
+ */
+struct pt_regs {
+#ifdef CONFIG_32BIT
+	/* Pad bytes for argument save space on the stack. */
+	unsigned long pad0[8];
+#endif
+
+	/* Saved main processor registers. */
+	unsigned long regs[32];
+
+	/* Saved special registers. */
+	unsigned long cp0_status;
+	unsigned long hi;
+	unsigned long lo;
+#ifdef CONFIG_CPU_HAS_SMARTMIPS
+	unsigned long acx;
+#endif
+	unsigned long cp0_badvaddr;
+	unsigned long cp0_cause;
+	unsigned long cp0_epc;
+#ifdef CONFIG_CPU_CAVIUM_OCTEON
+	unsigned long long mpl[6];        /* MTM{0-5} */
+	unsigned long long mtp[6];        /* MTP{0-5} */
+#endif
+	unsigned long __last[0];
+} __aligned(8);
+
+static inline unsigned long kernel_stack_pointer(struct pt_regs *regs)
+{
+	return regs->regs[29];
+}
+
+static inline void instruction_pointer_set(struct pt_regs *regs,
+                                           unsigned long val)
+{
+	regs->cp0_epc = val;
+}
+
+/* Query offset/name of register from its name/offset */
+extern int regs_query_register_offset(const char *name);
+#define MAX_REG_OFFSET (offsetof(struct pt_regs, __last))
+
+/**
+ * regs_get_register() - get register value from its offset
+ * @regs:       pt_regs from which register value is gotten.
+ * @offset:     offset number of the register.
+ *
+ * regs_get_register returns the value of a register. The @offset is the
+ * offset of the register in struct pt_regs address which specified by @regs.
+ * If @offset is bigger than MAX_REG_OFFSET, this returns 0.
+ */
+static inline unsigned long regs_get_register(struct pt_regs *regs,
+                                              unsigned int offset)
+{
+	if (unlikely(offset > MAX_REG_OFFSET))
+		return 0;
+
+	return *(unsigned long *)((unsigned long)regs + offset);
+}
+
+/**
+ * regs_within_kernel_stack() - check the address in the stack
+ * @regs:       pt_regs which contains kernel stack pointer.
+ * @addr:       address which is checked.
+ *
+ * regs_within_kernel_stack() checks @addr is within the kernel stack page(s).
+ * If @addr is within the kernel stack, it returns true. If not, returns false.
+ */
+static inline int regs_within_kernel_stack(struct pt_regs *regs,
+                                           unsigned long addr)
+{
+	return ((addr & ~(THREAD_SIZE - 1))  ==
+		(kernel_stack_pointer(regs) & ~(THREAD_SIZE - 1)));
+}
+
+/**
+ * regs_get_kernel_stack_nth() - get Nth entry of the stack
+ * @regs:       pt_regs which contains kernel stack pointer.
+ * @n:          stack entry number.
+ *
+ * regs_get_kernel_stack_nth() returns @n th entry of the kernel stack which
+ * is specified by @regs. If the @n th entry is NOT in the kernel stack,
+ * this returns 0.
+ */
+static inline unsigned long regs_get_kernel_stack_nth(struct pt_regs *regs,
+                                                      unsigned int n)
+{
+	unsigned long *addr = (unsigned long *)kernel_stack_pointer(regs);
+
+	addr += n;
+	if (regs_within_kernel_stack(regs, (unsigned long)addr))
+		return *addr;
+	else
+		return 0;
+}
+
+struct task_struct;
+
+extern int ptrace_getregs(struct task_struct *child,
+	struct user_pt_regs __user *data);
+extern int ptrace_setregs(struct task_struct *child,
+	struct user_pt_regs __user *data);
+
+extern int ptrace_getfpregs(struct task_struct *child, __u32 __user *data);
+extern int ptrace_setfpregs(struct task_struct *child, __u32 __user *data);
+
+extern int ptrace_get_watch_regs(struct task_struct *child,
+	struct pt_watch_regs __user *addr);
+extern int ptrace_set_watch_regs(struct task_struct *child,
+	struct pt_watch_regs __user *addr);
+
+/*
+ * Does the process account for user or for system time?
+ */
+#define user_mode(regs) (((regs)->cp0_status & KU_MASK) == KU_USER)
+
+static inline int is_syscall_success(struct pt_regs *regs)
+{
+	return !regs->regs[7];
+}
+
+static inline long regs_return_value(struct pt_regs *regs)
+{
+	if (is_syscall_success(regs) || !user_mode(regs))
+		return regs->regs[2];
+	else
+		return -regs->regs[2];
+}
+
+#define instruction_pointer(regs) ((regs)->cp0_epc)
+#define profile_pc(regs) instruction_pointer(regs)
+
+extern asmlinkage long syscall_trace_enter(struct pt_regs *regs, long syscall);
+extern asmlinkage void syscall_trace_leave(struct pt_regs *regs);
+
+extern void die(const char *, struct pt_regs *) __noreturn;
+
+static inline void die_if_kernel(const char *str, struct pt_regs *regs)
+{
+	if (unlikely(!user_mode(regs)))
+		die(str, regs);
+}
+
+#define current_pt_regs()						\
+({									\
+	unsigned long sp = (unsigned long)__builtin_frame_address(0);	\
+	(struct pt_regs *)((sp | (THREAD_SIZE - 1)) + 1 - 32) - 1;	\
+})
+
+/* Helpers for working with the user stack pointer */
+
+static inline unsigned long user_stack_pointer(struct pt_regs *regs)
+{
+	return regs->regs[29];
+}
+
+static inline void user_stack_pointer_set(struct pt_regs *regs,
+	unsigned long val)
+{
+	regs->regs[29] = val;
+}
+
+#endif /* _ASM_PTRACE_H */
diff --git a/arch/mips/include/asm/r4k-timer.h b/arch/mips/include/asm/r4k-timer.h
new file mode 100644
index 000000000..6e7361629
--- /dev/null
+++ b/arch/mips/include/asm/r4k-timer.h
@@ -0,0 +1,30 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 by Ralf Baechle (ralf@linux-mips.org)
+ */
+#ifndef __ASM_R4K_TIMER_H
+#define __ASM_R4K_TIMER_H
+
+#include <linux/compiler.h>
+
+#ifdef CONFIG_SYNC_R4K
+
+extern void synchronise_count_master(int cpu);
+extern void synchronise_count_slave(int cpu);
+
+#else
+
+static inline void synchronise_count_master(int cpu)
+{
+}
+
+static inline void synchronise_count_slave(int cpu)
+{
+}
+
+#endif
+
+#endif /* __ASM_R4K_TIMER_H */
diff --git a/arch/mips/include/asm/r4kcache.h b/arch/mips/include/asm/r4kcache.h
new file mode 100644
index 000000000..431a1c9d5
--- /dev/null
+++ b/arch/mips/include/asm/r4kcache.h
@@ -0,0 +1,334 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Inline assembly cache operations.
+ *
+ * Copyright (C) 1996 David S. Miller (davem@davemloft.net)
+ * Copyright (C) 1997 - 2002 Ralf Baechle (ralf@gnu.org)
+ * Copyright (C) 2004 Ralf Baechle (ralf@linux-mips.org)
+ */
+#ifndef _ASM_R4KCACHE_H
+#define _ASM_R4KCACHE_H
+
+#include <linux/stringify.h>
+
+#include <asm/asm.h>
+#include <asm/asm-eva.h>
+#include <asm/cacheops.h>
+#include <asm/compiler.h>
+#include <asm/cpu-features.h>
+#include <asm/cpu-type.h>
+#include <asm/mipsmtregs.h>
+#include <asm/mmzone.h>
+#include <asm/unroll.h>
+
+extern void (*r4k_blast_dcache)(void);
+extern void (*r4k_blast_icache)(void);
+
+/*
+ * This macro return a properly sign-extended address suitable as base address
+ * for indexed cache operations.  Two issues here:
+ *
+ *  - The MIPS32 and MIPS64 specs permit an implementation to directly derive
+ *    the index bits from the virtual address.	This breaks with tradition
+ *    set by the R4000.	 To keep unpleasant surprises from happening we pick
+ *    an address in KSEG0 / CKSEG0.
+ *  - We need a properly sign extended address for 64-bit code.	 To get away
+ *    without ifdefs we let the compiler do it by a type cast.
+ */
+#define INDEX_BASE	CKSEG0
+
+#define _cache_op(insn, op, addr)					\
+	__asm__ __volatile__(						\
+	"	.set	push					\n"	\
+	"	.set	noreorder				\n"	\
+	"	.set "MIPS_ISA_ARCH_LEVEL"			\n"	\
+	"	" insn("%0", "%1") "				\n"	\
+	"	.set	pop					\n"	\
+	:								\
+	: "i" (op), "R" (*(unsigned char *)(addr)))
+
+#define cache_op(op, addr)						\
+	_cache_op(kernel_cache, op, addr)
+
+static inline void flush_icache_line_indexed(unsigned long addr)
+{
+	cache_op(Index_Invalidate_I, addr);
+}
+
+static inline void flush_dcache_line_indexed(unsigned long addr)
+{
+	cache_op(Index_Writeback_Inv_D, addr);
+}
+
+static inline void flush_scache_line_indexed(unsigned long addr)
+{
+	cache_op(Index_Writeback_Inv_SD, addr);
+}
+
+static inline void flush_icache_line(unsigned long addr)
+{
+	switch (boot_cpu_type()) {
+	case CPU_LOONGSON2EF:
+		cache_op(Hit_Invalidate_I_Loongson2, addr);
+		break;
+
+	default:
+		cache_op(Hit_Invalidate_I, addr);
+		break;
+	}
+}
+
+static inline void flush_dcache_line(unsigned long addr)
+{
+	cache_op(Hit_Writeback_Inv_D, addr);
+}
+
+static inline void invalidate_dcache_line(unsigned long addr)
+{
+	cache_op(Hit_Invalidate_D, addr);
+}
+
+static inline void invalidate_scache_line(unsigned long addr)
+{
+	cache_op(Hit_Invalidate_SD, addr);
+}
+
+static inline void flush_scache_line(unsigned long addr)
+{
+	cache_op(Hit_Writeback_Inv_SD, addr);
+}
+
+#ifdef CONFIG_EVA
+
+#define protected_cache_op(op, addr)				\
+({								\
+	int __err = 0;						\
+	__asm__ __volatile__(					\
+	"	.set	push			\n"		\
+	"	.set	noreorder		\n"		\
+	"	.set	mips0			\n"		\
+	"	.set	eva			\n"		\
+	"1:	cachee	%1, (%2)		\n"		\
+	"2:	.insn				\n"		\
+	"	.set	pop			\n"		\
+	"	.section .fixup,\"ax\"		\n"		\
+	"3:	li	%0, %3			\n"		\
+	"	j	2b			\n"		\
+	"	.previous			\n"		\
+	"	.section __ex_table,\"a\"	\n"		\
+	"	"STR(PTR_WD)" 1b, 3b		\n"		\
+	"	.previous"					\
+	: "+r" (__err)						\
+	: "i" (op), "r" (addr), "i" (-EFAULT));			\
+	__err;							\
+})
+#else
+
+#define protected_cache_op(op, addr)				\
+({								\
+	int __err = 0;						\
+	__asm__ __volatile__(					\
+	"	.set	push			\n"		\
+	"	.set	noreorder		\n"		\
+	"	.set "MIPS_ISA_ARCH_LEVEL"	\n"		\
+	"1:	cache	%1, (%2)		\n"		\
+	"2:	.insn				\n"		\
+	"	.set	pop			\n"		\
+	"	.section .fixup,\"ax\"		\n"		\
+	"3:	li	%0, %3			\n"		\
+	"	j	2b			\n"		\
+	"	.previous			\n"		\
+	"	.section __ex_table,\"a\"	\n"		\
+	"	"STR(PTR_WD)" 1b, 3b		\n"		\
+	"	.previous"					\
+	: "+r" (__err)						\
+	: "i" (op), "r" (addr), "i" (-EFAULT));			\
+	__err;							\
+})
+#endif
+
+/*
+ * The next two are for badland addresses like signal trampolines.
+ */
+static inline int protected_flush_icache_line(unsigned long addr)
+{
+	switch (boot_cpu_type()) {
+	case CPU_LOONGSON2EF:
+		return protected_cache_op(Hit_Invalidate_I_Loongson2, addr);
+
+	default:
+		return protected_cache_op(Hit_Invalidate_I, addr);
+	}
+}
+
+/*
+ * R10000 / R12000 hazard - these processors don't support the Hit_Writeback_D
+ * cacheop so we use Hit_Writeback_Inv_D which is supported by all R4000-style
+ * caches.  We're talking about one cacheline unnecessarily getting invalidated
+ * here so the penalty isn't overly hard.
+ */
+static inline int protected_writeback_dcache_line(unsigned long addr)
+{
+	return protected_cache_op(Hit_Writeback_Inv_D, addr);
+}
+
+static inline int protected_writeback_scache_line(unsigned long addr)
+{
+	return protected_cache_op(Hit_Writeback_Inv_SD, addr);
+}
+
+/*
+ * This one is RM7000-specific
+ */
+static inline void invalidate_tcache_page(unsigned long addr)
+{
+	cache_op(Page_Invalidate_T, addr);
+}
+
+#define cache_unroll(times, insn, op, addr, lsize) do {			\
+	int i = 0;							\
+	unroll(times, _cache_op, insn, op, (addr) + (i++ * (lsize)));	\
+} while (0)
+
+/* build blast_xxx, blast_xxx_page, blast_xxx_page_indexed */
+#define __BUILD_BLAST_CACHE(pfx, desc, indexop, hitop, lsize, extra)	\
+static inline void extra##blast_##pfx##cache##lsize(void)		\
+{									\
+	unsigned long start = INDEX_BASE;				\
+	unsigned long end = start + current_cpu_data.desc.waysize;	\
+	unsigned long ws_inc = 1UL << current_cpu_data.desc.waybit;	\
+	unsigned long ws_end = current_cpu_data.desc.ways <<		\
+			       current_cpu_data.desc.waybit;		\
+	unsigned long ws, addr;						\
+									\
+	for (ws = 0; ws < ws_end; ws += ws_inc)				\
+		for (addr = start; addr < end; addr += lsize * 32)	\
+			cache_unroll(32, kernel_cache, indexop,		\
+				     addr | ws, lsize);			\
+}									\
+									\
+static inline void extra##blast_##pfx##cache##lsize##_page(unsigned long page) \
+{									\
+	unsigned long start = page;					\
+	unsigned long end = page + PAGE_SIZE;				\
+									\
+	do {								\
+		cache_unroll(32, kernel_cache, hitop, start, lsize);	\
+		start += lsize * 32;					\
+	} while (start < end);						\
+}									\
+									\
+static inline void extra##blast_##pfx##cache##lsize##_page_indexed(unsigned long page) \
+{									\
+	unsigned long indexmask = current_cpu_data.desc.waysize - 1;	\
+	unsigned long start = INDEX_BASE + (page & indexmask);		\
+	unsigned long end = start + PAGE_SIZE;				\
+	unsigned long ws_inc = 1UL << current_cpu_data.desc.waybit;	\
+	unsigned long ws_end = current_cpu_data.desc.ways <<		\
+			       current_cpu_data.desc.waybit;		\
+	unsigned long ws, addr;						\
+									\
+	for (ws = 0; ws < ws_end; ws += ws_inc)				\
+		for (addr = start; addr < end; addr += lsize * 32)	\
+			cache_unroll(32, kernel_cache, indexop,		\
+				     addr | ws, lsize);			\
+}
+
+__BUILD_BLAST_CACHE(d, dcache, Index_Writeback_Inv_D, Hit_Writeback_Inv_D, 16, )
+__BUILD_BLAST_CACHE(i, icache, Index_Invalidate_I, Hit_Invalidate_I, 16, )
+__BUILD_BLAST_CACHE(s, scache, Index_Writeback_Inv_SD, Hit_Writeback_Inv_SD, 16, )
+__BUILD_BLAST_CACHE(d, dcache, Index_Writeback_Inv_D, Hit_Writeback_Inv_D, 32, )
+__BUILD_BLAST_CACHE(i, icache, Index_Invalidate_I, Hit_Invalidate_I, 32, )
+__BUILD_BLAST_CACHE(i, icache, Index_Invalidate_I, Hit_Invalidate_I_Loongson2, 32, loongson2_)
+__BUILD_BLAST_CACHE(s, scache, Index_Writeback_Inv_SD, Hit_Writeback_Inv_SD, 32, )
+__BUILD_BLAST_CACHE(d, dcache, Index_Writeback_Inv_D, Hit_Writeback_Inv_D, 64, )
+__BUILD_BLAST_CACHE(i, icache, Index_Invalidate_I, Hit_Invalidate_I, 64, )
+__BUILD_BLAST_CACHE(s, scache, Index_Writeback_Inv_SD, Hit_Writeback_Inv_SD, 64, )
+__BUILD_BLAST_CACHE(d, dcache, Index_Writeback_Inv_D, Hit_Writeback_Inv_D, 128, )
+__BUILD_BLAST_CACHE(i, icache, Index_Invalidate_I, Hit_Invalidate_I, 128, )
+__BUILD_BLAST_CACHE(s, scache, Index_Writeback_Inv_SD, Hit_Writeback_Inv_SD, 128, )
+
+__BUILD_BLAST_CACHE(inv_d, dcache, Index_Writeback_Inv_D, Hit_Invalidate_D, 16, )
+__BUILD_BLAST_CACHE(inv_d, dcache, Index_Writeback_Inv_D, Hit_Invalidate_D, 32, )
+__BUILD_BLAST_CACHE(inv_s, scache, Index_Writeback_Inv_SD, Hit_Invalidate_SD, 16, )
+__BUILD_BLAST_CACHE(inv_s, scache, Index_Writeback_Inv_SD, Hit_Invalidate_SD, 32, )
+__BUILD_BLAST_CACHE(inv_s, scache, Index_Writeback_Inv_SD, Hit_Invalidate_SD, 64, )
+__BUILD_BLAST_CACHE(inv_s, scache, Index_Writeback_Inv_SD, Hit_Invalidate_SD, 128, )
+
+#define __BUILD_BLAST_USER_CACHE(pfx, desc, indexop, hitop, lsize) \
+static inline void blast_##pfx##cache##lsize##_user_page(unsigned long page) \
+{									\
+	unsigned long start = page;					\
+	unsigned long end = page + PAGE_SIZE;				\
+									\
+	do {								\
+		cache_unroll(32, user_cache, hitop, start, lsize);	\
+		start += lsize * 32;					\
+	} while (start < end);						\
+}
+
+__BUILD_BLAST_USER_CACHE(d, dcache, Index_Writeback_Inv_D, Hit_Writeback_Inv_D,
+			 16)
+__BUILD_BLAST_USER_CACHE(i, icache, Index_Invalidate_I, Hit_Invalidate_I, 16)
+__BUILD_BLAST_USER_CACHE(d, dcache, Index_Writeback_Inv_D, Hit_Writeback_Inv_D,
+			 32)
+__BUILD_BLAST_USER_CACHE(i, icache, Index_Invalidate_I, Hit_Invalidate_I, 32)
+__BUILD_BLAST_USER_CACHE(d, dcache, Index_Writeback_Inv_D, Hit_Writeback_Inv_D,
+			 64)
+__BUILD_BLAST_USER_CACHE(i, icache, Index_Invalidate_I, Hit_Invalidate_I, 64)
+
+/* build blast_xxx_range, protected_blast_xxx_range */
+#define __BUILD_BLAST_CACHE_RANGE(pfx, desc, hitop, prot, extra)	\
+static inline void prot##extra##blast_##pfx##cache##_range(unsigned long start, \
+						    unsigned long end)	\
+{									\
+	unsigned long lsize = cpu_##desc##_line_size();			\
+	unsigned long addr = start & ~(lsize - 1);			\
+	unsigned long aend = (end - 1) & ~(lsize - 1);			\
+									\
+	while (1) {							\
+		prot##cache_op(hitop, addr);				\
+		if (addr == aend)					\
+			break;						\
+		addr += lsize;						\
+	}								\
+}
+
+__BUILD_BLAST_CACHE_RANGE(d, dcache, Hit_Writeback_Inv_D, protected_, )
+__BUILD_BLAST_CACHE_RANGE(i, icache, Hit_Invalidate_I, protected_, )
+__BUILD_BLAST_CACHE_RANGE(s, scache, Hit_Writeback_Inv_SD, protected_, )
+__BUILD_BLAST_CACHE_RANGE(i, icache, Hit_Invalidate_I_Loongson2, \
+	protected_, loongson2_)
+__BUILD_BLAST_CACHE_RANGE(d, dcache, Hit_Writeback_Inv_D, , )
+__BUILD_BLAST_CACHE_RANGE(i, icache, Hit_Invalidate_I, , )
+__BUILD_BLAST_CACHE_RANGE(s, scache, Hit_Writeback_Inv_SD, , )
+/* blast_inv_dcache_range */
+__BUILD_BLAST_CACHE_RANGE(inv_d, dcache, Hit_Invalidate_D, , )
+__BUILD_BLAST_CACHE_RANGE(inv_s, scache, Hit_Invalidate_SD, , )
+
+/* Currently, this is very specific to Loongson-3 */
+#define __BUILD_BLAST_CACHE_NODE(pfx, desc, indexop, hitop, lsize)	\
+static inline void blast_##pfx##cache##lsize##_node(long node)		\
+{									\
+	unsigned long start = CAC_BASE | nid_to_addrbase(node);		\
+	unsigned long end = start + current_cpu_data.desc.waysize;	\
+	unsigned long ws_inc = 1UL << current_cpu_data.desc.waybit;	\
+	unsigned long ws_end = current_cpu_data.desc.ways <<		\
+			       current_cpu_data.desc.waybit;		\
+	unsigned long ws, addr;						\
+									\
+	for (ws = 0; ws < ws_end; ws += ws_inc)				\
+		for (addr = start; addr < end; addr += lsize * 32)	\
+			cache_unroll(32, kernel_cache, indexop,		\
+				     addr | ws, lsize);			\
+}
+
+__BUILD_BLAST_CACHE_NODE(s, scache, Index_Writeback_Inv_SD, Hit_Writeback_Inv_SD, 16)
+__BUILD_BLAST_CACHE_NODE(s, scache, Index_Writeback_Inv_SD, Hit_Writeback_Inv_SD, 32)
+__BUILD_BLAST_CACHE_NODE(s, scache, Index_Writeback_Inv_SD, Hit_Writeback_Inv_SD, 64)
+__BUILD_BLAST_CACHE_NODE(s, scache, Index_Writeback_Inv_SD, Hit_Writeback_Inv_SD, 128)
+
+#endif /* _ASM_R4KCACHE_H */
diff --git a/arch/mips/include/asm/reboot.h b/arch/mips/include/asm/reboot.h
new file mode 100644
index 000000000..e48c0bfab
--- /dev/null
+++ b/arch/mips/include/asm/reboot.h
@@ -0,0 +1,15 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1997, 1999, 2001, 06 by Ralf Baechle
+ * Copyright (C) 2001 MIPS Technologies, Inc.
+ */
+#ifndef _ASM_REBOOT_H
+#define _ASM_REBOOT_H
+
+extern void (*_machine_restart)(char *command);
+extern void (*_machine_halt)(void);
+
+#endif /* _ASM_REBOOT_H */
diff --git a/arch/mips/include/asm/reg.h b/arch/mips/include/asm/reg.h
new file mode 100644
index 000000000..84dc7e2e2
--- /dev/null
+++ b/arch/mips/include/asm/reg.h
@@ -0,0 +1 @@
+#include <uapi/asm/reg.h>
diff --git a/arch/mips/include/asm/regdef.h b/arch/mips/include/asm/regdef.h
new file mode 100644
index 000000000..3c687df1d
--- /dev/null
+++ b/arch/mips/include/asm/regdef.h
@@ -0,0 +1,106 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1985 MIPS Computer Systems, Inc.
+ * Copyright (C) 1994, 95, 99, 2003 by Ralf Baechle
+ * Copyright (C) 1990 - 1992, 1999 Silicon Graphics, Inc.
+ * Copyright (C) 2011 Wind River Systems,
+ *   written by Ralf Baechle <ralf@linux-mips.org>
+ */
+#ifndef _ASM_REGDEF_H
+#define _ASM_REGDEF_H
+
+#include <asm/sgidefs.h>
+
+#if _MIPS_SIM == _MIPS_SIM_ABI32
+
+/*
+ * Symbolic register names for 32 bit ABI
+ */
+#define zero	$0	/* wired zero */
+#define AT	$1	/* assembler temp  - uppercase because of ".set at" */
+#define v0	$2	/* return value */
+#define v1	$3
+#define a0	$4	/* argument registers */
+#define a1	$5
+#define a2	$6
+#define a3	$7
+#define t0	$8	/* caller saved */
+#define t1	$9
+#define t2	$10
+#define t3	$11
+#define t4	$12
+#define ta0	$12
+#define t5	$13
+#define ta1	$13
+#define t6	$14
+#define ta2	$14
+#define t7	$15
+#define ta3	$15
+#define s0	$16	/* callee saved */
+#define s1	$17
+#define s2	$18
+#define s3	$19
+#define s4	$20
+#define s5	$21
+#define s6	$22
+#define s7	$23
+#define t8	$24	/* caller saved */
+#define t9	$25
+#define jp	$25	/* PIC jump register */
+#define k0	$26	/* kernel scratch */
+#define k1	$27
+#define gp	$28	/* global pointer */
+#define sp	$29	/* stack pointer */
+#define fp	$30	/* frame pointer */
+#define s8	$30	/* same like fp! */
+#define ra	$31	/* return address */
+
+#endif /* _MIPS_SIM == _MIPS_SIM_ABI32 */
+
+#if _MIPS_SIM == _MIPS_SIM_ABI64 || _MIPS_SIM == _MIPS_SIM_NABI32
+
+#define zero	$0	/* wired zero */
+#define AT	$at	/* assembler temp - uppercase because of ".set at" */
+#define v0	$2	/* return value - caller saved */
+#define v1	$3
+#define a0	$4	/* argument registers */
+#define a1	$5
+#define a2	$6
+#define a3	$7
+#define a4	$8	/* arg reg 64 bit; caller saved in 32 bit */
+#define ta0	$8
+#define a5	$9
+#define ta1	$9
+#define a6	$10
+#define ta2	$10
+#define a7	$11
+#define ta3	$11
+#define t0	$12	/* caller saved */
+#define t1	$13
+#define t2	$14
+#define t3	$15
+#define s0	$16	/* callee saved */
+#define s1	$17
+#define s2	$18
+#define s3	$19
+#define s4	$20
+#define s5	$21
+#define s6	$22
+#define s7	$23
+#define t8	$24	/* caller saved */
+#define t9	$25	/* callee address for PIC/temp */
+#define jp	$25	/* PIC jump register */
+#define k0	$26	/* kernel temporary */
+#define k1	$27
+#define gp	$28	/* global pointer - caller saved for PIC */
+#define sp	$29	/* stack pointer */
+#define fp	$30	/* frame pointer */
+#define s8	$30	/* callee saved */
+#define ra	$31	/* return address */
+
+#endif /* _MIPS_SIM == _MIPS_SIM_ABI64 || _MIPS_SIM == _MIPS_SIM_NABI32 */
+
+#endif /* _ASM_REGDEF_H */
diff --git a/arch/mips/include/asm/rtlx.h b/arch/mips/include/asm/rtlx.h
new file mode 100644
index 000000000..c10206548
--- /dev/null
+++ b/arch/mips/include/asm/rtlx.h
@@ -0,0 +1,88 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2004, 2005 MIPS Technologies, Inc.  All rights reserved.
+ * Copyright (C) 2013 Imagination Technologies Ltd.
+ */
+#ifndef __ASM_RTLX_H_
+#define __ASM_RTLX_H_
+
+#include <irq.h>
+
+#define RTLX_MODULE_NAME "rtlx"
+
+#define LX_NODE_BASE 10
+
+#define MIPS_CPU_RTLX_IRQ 0
+
+#define RTLX_VERSION 2
+#define RTLX_xID 0x12345600
+#define RTLX_ID (RTLX_xID | RTLX_VERSION)
+#define RTLX_BUFFER_SIZE 2048
+#define RTLX_CHANNELS 8
+
+#define RTLX_CHANNEL_STDIO	0
+#define RTLX_CHANNEL_DBG	1
+#define RTLX_CHANNEL_SYSIO	2
+
+void rtlx_starting(int vpe);
+void rtlx_stopping(int vpe);
+
+int rtlx_open(int index, int can_sleep);
+int rtlx_release(int index);
+ssize_t rtlx_read(int index, void __user *buff, size_t count);
+ssize_t rtlx_write(int index, const void __user *buffer, size_t count);
+unsigned int rtlx_read_poll(int index, int can_sleep);
+unsigned int rtlx_write_poll(int index);
+
+int __init rtlx_module_init(void);
+void __exit rtlx_module_exit(void);
+
+void _interrupt_sp(void);
+
+extern struct vpe_notifications rtlx_notify;
+extern const struct file_operations rtlx_fops;
+extern void (*aprp_hook)(void);
+
+enum rtlx_state {
+	RTLX_STATE_UNUSED = 0,
+	RTLX_STATE_INITIALISED,
+	RTLX_STATE_REMOTE_READY,
+	RTLX_STATE_OPENED
+};
+
+extern struct chan_waitqueues {
+	wait_queue_head_t rt_queue;
+	wait_queue_head_t lx_queue;
+	atomic_t in_open;
+	struct mutex mutex;
+} channel_wqs[RTLX_CHANNELS];
+
+/* each channel supports read and write.
+   linux (vpe0) reads lx_buffer and writes rt_buffer
+   SP (vpe1) reads rt_buffer and writes lx_buffer
+*/
+struct rtlx_channel {
+	enum rtlx_state rt_state;
+	enum rtlx_state lx_state;
+
+	int buffer_size;
+
+	/* read and write indexes per buffer */
+	int rt_write, rt_read;
+	char *rt_buffer;
+
+	int lx_write, lx_read;
+	char *lx_buffer;
+};
+
+extern struct rtlx_info {
+	unsigned long id;
+	enum rtlx_state state;
+	int ap_int_pending;	/* Status of 0 or 1 for CONFIG_MIPS_CMP only */
+
+	struct rtlx_channel channel[RTLX_CHANNELS];
+} *rtlx;
+#endif /* __ASM_RTLX_H_ */
diff --git a/arch/mips/include/asm/seccomp.h b/arch/mips/include/asm/seccomp.h
new file mode 100644
index 000000000..aa809589a
--- /dev/null
+++ b/arch/mips/include/asm/seccomp.h
@@ -0,0 +1,35 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_SECCOMP_H
+
+#include <linux/unistd.h>
+
+#ifdef CONFIG_COMPAT
+static inline const int *get_compat_mode1_syscalls(void)
+{
+	static const int syscalls_O32[] = {
+		__NR_O32_Linux + 3, __NR_O32_Linux + 4,
+		__NR_O32_Linux + 1, __NR_O32_Linux + 193,
+		-1, /* negative terminated */
+	};
+	static const int syscalls_N32[] = {
+		__NR_N32_Linux + 0, __NR_N32_Linux + 1,
+		__NR_N32_Linux + 58, __NR_N32_Linux + 211,
+		-1, /* negative terminated */
+	};
+
+	if (IS_ENABLED(CONFIG_MIPS32_O32) && test_thread_flag(TIF_32BIT_REGS))
+		return syscalls_O32;
+
+	if (IS_ENABLED(CONFIG_MIPS32_N32))
+		return syscalls_N32;
+
+	BUG();
+}
+
+#define get_compat_mode1_syscalls get_compat_mode1_syscalls
+
+#endif /* CONFIG_COMPAT */
+
+#include <asm-generic/seccomp.h>
+
+#endif /* __ASM_SECCOMP_H */
diff --git a/arch/mips/include/asm/setup.h b/arch/mips/include/asm/setup.h
new file mode 100644
index 000000000..8c56b862f
--- /dev/null
+++ b/arch/mips/include/asm/setup.h
@@ -0,0 +1,31 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _MIPS_SETUP_H
+#define _MIPS_SETUP_H
+
+#include <linux/types.h>
+#include <uapi/asm/setup.h>
+
+extern void prom_putchar(char);
+extern void setup_early_printk(void);
+
+#ifdef CONFIG_EARLY_PRINTK_8250
+extern void setup_8250_early_printk_port(unsigned long base,
+	unsigned int reg_shift, unsigned int timeout);
+#else
+static inline void setup_8250_early_printk_port(unsigned long base,
+	unsigned int reg_shift, unsigned int timeout) {}
+#endif
+
+void set_handler(unsigned long offset, const void *addr, unsigned long len);
+extern void set_uncached_handler(unsigned long offset, void *addr, unsigned long len);
+
+typedef void (*vi_handler_t)(void);
+extern void *set_vi_handler(int n, vi_handler_t addr);
+
+extern void *set_except_vector(int n, void *addr);
+extern unsigned long ebase;
+extern unsigned int hwrena;
+extern void per_cpu_trap_init(bool);
+extern void cpu_cache_init(void);
+
+#endif /* __SETUP_H */
diff --git a/arch/mips/include/asm/sgi/gio.h b/arch/mips/include/asm/sgi/gio.h
new file mode 100644
index 000000000..24be2b425
--- /dev/null
+++ b/arch/mips/include/asm/sgi/gio.h
@@ -0,0 +1,86 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * gio.h: Definitions for SGI GIO bus
+ *
+ * Copyright (C) 2002 Ladislav Michl
+ */
+
+#ifndef _SGI_GIO_H
+#define _SGI_GIO_H
+
+/*
+ * GIO bus addresses
+ *
+ * The Indigo and Indy have two GIO bus connectors. Indigo2 (all models) have
+ * three physical connectors, but only two slots, GFX and EXP0.
+ *
+ * There is 10MB of GIO address space for GIO64 slot devices
+ * slot#   slot type address range	      size
+ * -----   --------- ----------------------- -----
+ *   0	   GFX	     0x1f000000 - 0x1f3fffff   4MB
+ *   1	   EXP0	     0x1f400000 - 0x1f5fffff   2MB
+ *   2	   EXP1	     0x1f600000 - 0x1f9fffff   4MB
+ *
+ * There are un-slotted devices, HPC, I/O and misc devices, which are grouped
+ * into the HPC address space.
+ *   -	   MISC	     0x1fb00000 - 0x1fbfffff   1MB
+ *
+ * Following space is reserved and unused
+ *   -	   RESERVED  0x18000000 - 0x1effffff 112MB
+ *
+ * GIO bus IDs
+ *
+ * Each GIO bus device identifies itself to the system by answering a
+ * read with an "ID" value. IDs are either 8 or 32 bits long. IDs less
+ * than 128 are 8 bits long, with the most significant 24 bits read from
+ * the slot undefined.
+ *
+ * 32-bit IDs are divided into
+ *	bits 0:6	the product ID; ranges from 0x00 to 0x7F.
+ *	bit 7		0=GIO Product ID is 8 bits wide
+ *			1=GIO Product ID is 32 bits wide.
+ *	bits 8:15	manufacturer version for the product.
+ *	bit 16		0=GIO32 and GIO32-bis, 1=GIO64.
+ *	bit 17		0=no ROM present
+ *			1=ROM present on this board AND next three words
+ *			space define the ROM.
+ *	bits 18:31	up to manufacturer.
+ *
+ * IDs above 0x50/0xd0 are of 3rd party boards.
+ *
+ * 8-bit IDs
+ *	0x01		XPI low cost FDDI
+ *	0x02		GTR TokenRing
+ *	0x04		Synchronous ISDN
+ *	0x05		ATM board [*]
+ *	0x06		Canon Interface
+ *	0x07		16 bit SCSI Card [*]
+ *	0x08		JPEG (Double Wide)
+ *	0x09		JPEG (Single Wide)
+ *	0x0a		XPI mez. FDDI device 0
+ *	0x0b		XPI mez. FDDI device 1
+ *	0x0c		SMPTE 259M Video [*]
+ *	0x0d		Babblefish Compression [*]
+ *	0x0e		E-Plex 8-port Ethernet
+ *	0x30		Lyon Lamb IVAS
+ *	0xb8		GIO 100BaseTX Fast Ethernet (gfe)
+ *
+ * [*] Device provide 32-bit ID.
+ *
+ */
+
+#define GIO_ID(x)		(x & 0x7f)
+#define GIO_32BIT_ID		0x80
+#define GIO_REV(x)		((x >> 8) & 0xff)
+#define GIO_64BIT_IFACE		0x10000
+#define GIO_ROM_PRESENT		0x20000
+#define GIO_VENDOR_CODE(x)	((x >> 18) & 0x3fff)
+
+#define GIO_SLOT_GFX_BASE	0x1f000000
+#define GIO_SLOT_EXP0_BASE	0x1f400000
+#define GIO_SLOT_EXP1_BASE	0x1f600000
+
+#endif /* _SGI_GIO_H */
diff --git a/arch/mips/include/asm/sgi/heart.h b/arch/mips/include/asm/sgi/heart.h
new file mode 100644
index 000000000..0d0375195
--- /dev/null
+++ b/arch/mips/include/asm/sgi/heart.h
@@ -0,0 +1,323 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * HEART chip definitions
+ *
+ * Copyright (C) 2004-2007 Stanislaw Skowronek <skylark@unaligned.org>
+ *		 2009 Johannes Dickgreber <tanzy@gmx.de>
+ *		 2007-2015 Joshua Kinard <kumba@gentoo.org>
+ */
+#ifndef __ASM_SGI_HEART_H
+#define __ASM_SGI_HEART_H
+
+#include <linux/types.h>
+#include <linux/time.h>
+
+/*
+ * There are 8 DIMM slots on an IP30 system
+ * board, which are grouped into four banks
+ */
+#define HEART_MEMORY_BANKS	4
+
+/* HEART can support up to four CPUs */
+#define HEART_MAX_CPUS		4
+
+#define HEART_XKPHYS_BASE	((void *)(IO_BASE | 0x000000000ff00000ULL))
+
+/**
+ * struct ip30_heart_regs - struct that maps IP30 HEART registers.
+ * @mode: HEART_MODE - Purpose Unknown, machine reset called from here.
+ * @sdram_mode: HEART_SDRAM_MODE - purpose unknown.
+ * @mem_refresh: HEART_MEM_REF - purpose unknown.
+ * @mem_req_arb: HEART_MEM_REQ_ARB - purpose unknown.
+ * @mem_cfg.q: union for 64bit access to HEART_MEMCFG - 4x 64bit registers.
+ * @mem_cfg.l: union for 32bit access to HEART_MEMCFG - 8x 32bit registers.
+ * @fc_mode: HEART_FC_MODE - Purpose Unknown, possibly for GFX flow control.
+ * @fc_timer_limit: HEART_FC_TIMER_LIMIT - purpose unknown.
+ * @fc_addr: HEART_FC0_ADDR, HEART_FC1_ADDR - purpose unknown.
+ * @fc_credit_cnt: HEART_FC0_CR_CNT, HEART_FC1_CR_CNT - purpose unknown.
+ * @fc_timer: HEART_FC0_TIMER, HEART_FC1_TIMER - purpose unknown.
+ * @status: HEART_STATUS - HEART status information.
+ * @bus_err_addr: HEART_BERR_ADDR - likely contains addr of recent SIGBUS.
+ * @bus_err_misc: HEART_BERR_MISC - purpose unknown.
+ * @mem_err_addr: HEART_MEMERR_ADDR - likely contains addr of recent mem err.
+ * @mem_err_data: HEART_MEMERR_DATA - purpose unknown.
+ * @piur_acc_err: HEART_PIUR_ACC_ERR - likely for access err to HEART regs.
+ * @mlan_clock_div: HEART_MLAN_CLK_DIV - MicroLAN clock divider.
+ * @mlan_ctrl: HEART_MLAN_CTL - MicroLAN control.
+ * @__pad0: 0x0f40 bytes of padding -> next HEART register 0x01000.
+ * @undefined: Undefined/diag register, write to it triggers PIUR_ACC_ERR.
+ * @__pad1: 0xeff8 bytes of padding -> next HEART register 0x10000.
+ * @imr: HEART_IMR0 to HEART_IMR3 - per-cpu interrupt mask register.
+ * @set_isr: HEART_SET_ISR - set interrupt status register.
+ * @clear_isr: HEART_CLR_ISR - clear interrupt status register.
+ * @isr: HEART_ISR - interrupt status register (read-only).
+ * @imsr: HEART_IMSR - purpose unknown.
+ * @cause: HEART_CAUSE - HEART cause information.
+ * @__pad2: 0xffb8 bytes of padding -> next HEART register 0x20000.
+ * @count: HEART_COUNT - 52-bit counter.
+ * @__pad3: 0xfff8 bytes of padding -> next HEART register 0x30000.
+ * @compare: HEART_COMPARE - 24-bit compare.
+ * @__pad4: 0xfff8 bytes of padding -> next HEART register 0x40000.
+ * @trigger: HEART_TRIGGER - purpose unknown.
+ * @__pad5: 0xfff8 bytes of padding -> next HEART register 0x50000.
+ * @cpuid: HEART_PRID - contains CPU ID of CPU currently accessing HEART.
+ * @__pad6: 0xfff8 bytes of padding -> next HEART register 0x60000.
+ * @sync: HEART_SYNC - purpose unknown.
+ *
+ * HEART is the main system controller ASIC for IP30 system.  It incorporates
+ * a memory controller, interrupt status/cause/set/clear management, basic
+ * timer with count/compare, and other functionality.  For Linux, not all of
+ * HEART's functions are fully understood.
+ *
+ * Implementation note: All HEART registers are 64bits-wide, but the mem_cfg
+ * register only reports correct values if queried in 32bits.  Hence the need
+ * for a union.  Even though mem_cfg.l has 8 array slots, we only ever query
+ * up to 4 of those.  IP30 has 8 DIMM slots arranged into 4 banks, w/ 2 DIMMs
+ * per bank.  Each 32bit read accesses one of these banks.  Perhaps HEART was
+ * designed to address up to 8 banks (16 DIMMs)?  We may never know.
+ */
+struct ip30_heart_regs {		/* 0x0ff00000 */
+	u64 mode;			/* +  0x00000 */
+	/* Memory */
+	u64 sdram_mode;			/* +  0x00008 */
+	u64 mem_refresh;		/* +  0x00010 */
+	u64 mem_req_arb;		/* +  0x00018 */
+	union {
+		u64 q[HEART_MEMORY_BANKS];	/* readq() */
+		u32 l[HEART_MEMORY_BANKS * 2];	/* readl() */
+	} mem_cfg;			/* +  0x00020 */
+	/* Flow control (gfx?) */
+	u64 fc_mode;			/* +  0x00040 */
+	u64 fc_timer_limit;		/* +  0x00048 */
+	u64 fc_addr[2];			/* +  0x00050 */
+	u64 fc_credit_cnt[2];		/* +  0x00060 */
+	u64 fc_timer[2];		/* +  0x00070 */
+	/* Status */
+	u64 status;			/* +  0x00080 */
+	/* Bus error */
+	u64 bus_err_addr;		/* +  0x00088 */
+	u64 bus_err_misc;		/* +  0x00090 */
+	/* Memory error */
+	u64 mem_err_addr;		/* +  0x00098 */
+	u64 mem_err_data;		/* +  0x000a0 */
+	/* Misc */
+	u64 piur_acc_err;		/* +  0x000a8 */
+	u64 mlan_clock_div;		/* +  0x000b0 */
+	u64 mlan_ctrl;			/* +  0x000b8 */
+	u64 __pad0[0x01e8];		/* +  0x000c0 + 0x0f40 */
+	/* Undefined */
+	u64 undefined;			/* +  0x01000 */
+	u64 __pad1[0x1dff];		/* +  0x01008 + 0xeff8 */
+	/* Interrupts */
+	u64 imr[HEART_MAX_CPUS];	/* +  0x10000 */
+	u64 set_isr;			/* +  0x10020 */
+	u64 clear_isr;			/* +  0x10028 */
+	u64 isr;			/* +  0x10030 */
+	u64 imsr;			/* +  0x10038 */
+	u64 cause;			/* +  0x10040 */
+	u64 __pad2[0x1ff7];		/* +  0x10048 + 0xffb8 */
+	/* Timer */
+	u64 count;			/* +  0x20000 */
+	u64 __pad3[0x1fff];		/* +  0x20008 + 0xfff8 */
+	u64 compare;			/* +  0x30000 */
+	u64 __pad4[0x1fff];		/* +  0x30008 + 0xfff8 */
+	u64 trigger;			/* +  0x40000 */
+	u64 __pad5[0x1fff];		/* +  0x40008 + 0xfff8 */
+	/* Misc */
+	u64 cpuid;			/* +  0x50000 */
+	u64 __pad6[0x1fff];		/* +  0x50008 + 0xfff8 */
+	u64 sync;			/* +  0x60000 */
+};
+
+
+/* For timer-related bits. */
+#define HEART_NS_PER_CYCLE	80
+#define HEART_CYCLES_PER_SEC	(NSEC_PER_SEC / HEART_NS_PER_CYCLE)
+
+
+/*
+ * XXX: Everything below this comment will either go away or be cleaned
+ *      up to fit in better with Linux.  A lot of the bit definitions for
+ *      HEART were derived from IRIX's sys/RACER/heart.h header file.
+ */
+
+/* HEART Masks */
+#define HEART_ATK_MASK		0x0007ffffffffffff	/* HEART attack mask */
+#define HEART_ACK_ALL_MASK	0xffffffffffffffff	/* Ack everything */
+#define HEART_CLR_ALL_MASK	0x0000000000000000	/* Clear all */
+#define HEART_BR_ERR_MASK	0x7ff8000000000000	/* BRIDGE error mask */
+#define HEART_CPU0_ERR_MASK	0x8ff8000000000000	/* CPU0 error mask */
+#define HEART_CPU1_ERR_MASK	0x97f8000000000000	/* CPU1 error mask */
+#define HEART_CPU2_ERR_MASK	0xa7f8000000000000	/* CPU2 error mask */
+#define HEART_CPU3_ERR_MASK	0xc7f8000000000000	/* CPU3 error mask */
+#define HEART_ERR_MASK		0x1ff			/* HEART error mask */
+#define HEART_ERR_MASK_START	51			/* HEART error start */
+#define HEART_ERR_MASK_END	63			/* HEART error end */
+
+/* Bits in the HEART_MODE register. */
+#define HM_PROC_DISABLE_SHFT		60
+#define HM_PROC_DISABLE_MSK		(0xfUL << HM_PROC_DISABLE_SHFT)
+#define HM_PROC_DISABLE(x)		(0x1UL << (x) + HM_PROC_DISABLE_SHFT)
+#define HM_MAX_PSR			(0x7UL << 57)
+#define HM_MAX_IOSR			(0x7UL << 54)
+#define HM_MAX_PEND_IOSR		(0x7UL << 51)
+#define HM_TRIG_SRC_SEL_MSK		(0x7UL << 48)
+#define HM_TRIG_HEART_EXC		(0x0UL << 48)
+#define HM_TRIG_REG_BIT			(0x1UL << 48)
+#define HM_TRIG_SYSCLK			(0x2UL << 48)
+#define HM_TRIG_MEMCLK_2X		(0x3UL << 48)
+#define HM_TRIG_MEMCLK			(0x4UL << 48)
+#define HM_TRIG_IOCLK			(0x5UL << 48)
+#define HM_PIU_TEST_MODE		(0xfUL << 40)
+#define HM_GP_FLAG_MSK			(0xfUL << 36)
+#define HM_GP_FLAG(x)			BIT((x) + 36)
+#define HM_MAX_PROC_HYST		(0xfUL << 32)
+#define HM_LLP_WRST_AFTER_RST		BIT(28)
+#define HM_LLP_LINK_RST			BIT(27)
+#define HM_LLP_WARM_RST			BIT(26)
+#define HM_COR_ECC_LCK			BIT(25)
+#define HM_REDUCED_PWR			BIT(24)
+#define HM_COLD_RST			BIT(23)
+#define HM_SW_RST			BIT(22)
+#define HM_MEM_FORCE_WR			BIT(21)
+#define HM_DB_ERR_GEN			BIT(20)
+#define HM_SB_ERR_GEN			BIT(19)
+#define HM_CACHED_PIO_EN		BIT(18)
+#define HM_CACHED_PROM_EN		BIT(17)
+#define HM_PE_SYS_COR_ERE		BIT(16)
+#define HM_GLOBAL_ECC_EN		BIT(15)
+#define HM_IO_COH_EN			BIT(14)
+#define HM_INT_EN			BIT(13)
+#define HM_DATA_CHK_EN			BIT(12)
+#define HM_REF_EN			BIT(11)
+#define HM_BAD_SYSWR_ERE		BIT(10)
+#define HM_BAD_SYSRD_ERE		BIT(9)
+#define HM_SYSSTATE_ERE			BIT(8)
+#define HM_SYSCMD_ERE			BIT(7)
+#define HM_NCOR_SYS_ERE			BIT(6)
+#define HM_COR_SYS_ERE			BIT(5)
+#define HM_DATA_ELMNT_ERE		BIT(4)
+#define HM_MEM_ADDR_PROC_ERE		BIT(3)
+#define HM_MEM_ADDR_IO_ERE		BIT(2)
+#define HM_NCOR_MEM_ERE			BIT(1)
+#define HM_COR_MEM_ERE			BIT(0)
+
+/* Bits in the HEART_MEM_REF register. */
+#define HEART_MEMREF_REFS(x)		((0xfUL & (x)) << 16)
+#define HEART_MEMREF_PERIOD(x)		((0xffffUL & (x)))
+#define HEART_MEMREF_REFS_VAL		HEART_MEMREF_REFS(8)
+#define HEART_MEMREF_PERIOD_VAL		HEART_MEMREF_PERIOD(0x4000)
+#define HEART_MEMREF_VAL		(HEART_MEMREF_REFS_VAL | \
+					 HEART_MEMREF_PERIOD_VAL)
+
+/* Bits in the HEART_MEM_REQ_ARB register. */
+#define HEART_MEMARB_IODIS		(1  << 20)
+#define HEART_MEMARB_MAXPMWRQS		(15 << 16)
+#define HEART_MEMARB_MAXPMRRQS		(15 << 12)
+#define HEART_MEMARB_MAXPMRQS		(15 << 8)
+#define HEART_MEMARB_MAXRRRQS		(15 << 4)
+#define HEART_MEMARB_MAXGBRRQS		(15)
+
+/* Bits in the HEART_MEMCFG<x> registers. */
+#define HEART_MEMCFG_VALID		0x80000000	/* Bank is valid */
+#define HEART_MEMCFG_DENSITY		0x01c00000	/* Mem density */
+#define HEART_MEMCFG_SIZE_MASK		0x003f0000	/* Mem size mask */
+#define HEART_MEMCFG_ADDR_MASK		0x000001ff	/* Base addr mask */
+#define HEART_MEMCFG_SIZE_SHIFT		16		/* Mem size shift */
+#define HEART_MEMCFG_DENSITY_SHIFT	22		/* Density Shift */
+#define HEART_MEMCFG_UNIT_SHIFT		25		/* Unit Shift, 32MB */
+
+/* Bits in the HEART_STATUS register */
+#define HEART_STAT_HSTL_SDRV		BIT(14)
+#define HEART_STAT_FC_CR_OUT(x)		BIT((x) + 12)
+#define HEART_STAT_DIR_CNNCT		BIT(11)
+#define HEART_STAT_TRITON		BIT(10)
+#define HEART_STAT_R4K			BIT(9)
+#define HEART_STAT_BIG_ENDIAN		BIT(8)
+#define HEART_STAT_PROC_SHFT		4
+#define HEART_STAT_PROC_MSK		(0xfUL << HEART_STAT_PROC_SHFT)
+#define HEART_STAT_PROC_ACTIVE(x)	(0x1UL << ((x) + HEART_STAT_PROC_SHFT))
+#define HEART_STAT_WIDGET_ID		0xf
+
+/* Bits in the HEART_CAUSE register */
+#define HC_PE_SYS_COR_ERR_MSK		(0xfUL << 60)
+#define HC_PE_SYS_COR_ERR(x)		BIT((x) + 60)
+#define HC_PIOWDB_OFLOW			BIT(44)
+#define HC_PIORWRB_OFLOW		BIT(43)
+#define HC_PIUR_ACC_ERR			BIT(42)
+#define HC_BAD_SYSWR_ERR		BIT(41)
+#define HC_BAD_SYSRD_ERR		BIT(40)
+#define HC_SYSSTATE_ERR_MSK		(0xfUL << 36)
+#define HC_SYSSTATE_ERR(x)		BIT((x) + 36)
+#define HC_SYSCMD_ERR_MSK		(0xfUL << 32)
+#define HC_SYSCMD_ERR(x)		BIT((x) + 32)
+#define HC_NCOR_SYSAD_ERR_MSK		(0xfUL << 28)
+#define HC_NCOR_SYSAD_ERR(x)		BIT((x) + 28)
+#define HC_COR_SYSAD_ERR_MSK		(0xfUL << 24)
+#define HC_COR_SYSAD_ERR(x)		BIT((x) + 24)
+#define HC_DATA_ELMNT_ERR_MSK		(0xfUL << 20)
+#define HC_DATA_ELMNT_ERR(x)		BIT((x) + 20)
+#define HC_WIDGET_ERR			BIT(16)
+#define HC_MEM_ADDR_ERR_PROC_MSK	(0xfUL << 4)
+#define HC_MEM_ADDR_ERR_PROC(x)	BIT((x) + 4)
+#define HC_MEM_ADDR_ERR_IO		BIT(2)
+#define HC_NCOR_MEM_ERR			BIT(1)
+#define HC_COR_MEM_ERR			BIT(0)
+
+/*
+ * HEART has 64 interrupt vectors available to it, subdivided into five
+ * priority levels.  They are numbered 0 to 63.
+ */
+#define HEART_NUM_IRQS			64
+
+/*
+ * These are the five interrupt priority levels and their corresponding
+ * CPU IPx interrupt pins.
+ *
+ * Level 4 - Error Interrupts.
+ * Level 3 - HEART timer interrupt.
+ * Level 2 - CPU IPI, CPU debug, power putton, general device interrupts.
+ * Level 1 - General device interrupts.
+ * Level 0 - General device GFX flow control interrupts.
+ */
+#define HEART_L4_INT_MASK		0xfff8000000000000ULL	/* IP6 */
+#define HEART_L3_INT_MASK		0x0004000000000000ULL	/* IP5 */
+#define HEART_L2_INT_MASK		0x0003ffff00000000ULL	/* IP4 */
+#define HEART_L1_INT_MASK		0x00000000ffff0000ULL	/* IP3 */
+#define HEART_L0_INT_MASK		0x000000000000ffffULL	/* IP2 */
+
+/* HEART L0 Interrupts (Low Priority) */
+#define HEART_L0_INT_GENERIC		 0
+#define HEART_L0_INT_FLOW_CTRL_HWTR_0	 1
+#define HEART_L0_INT_FLOW_CTRL_HWTR_1	 2
+
+/* HEART L2 Interrupts (High Priority) */
+#define HEART_L2_INT_RESCHED_CPU_0	46
+#define HEART_L2_INT_RESCHED_CPU_1	47
+#define HEART_L2_INT_CALL_CPU_0		48
+#define HEART_L2_INT_CALL_CPU_1		49
+
+/* HEART L3 Interrupts (Compare/Counter Timer) */
+#define HEART_L3_INT_TIMER		50
+
+/* HEART L4 Interrupts (Errors) */
+#define HEART_L4_INT_XWID_ERR_9		51
+#define HEART_L4_INT_XWID_ERR_A		52
+#define HEART_L4_INT_XWID_ERR_B		53
+#define HEART_L4_INT_XWID_ERR_C		54
+#define HEART_L4_INT_XWID_ERR_D		55
+#define HEART_L4_INT_XWID_ERR_E		56
+#define HEART_L4_INT_XWID_ERR_F		57
+#define HEART_L4_INT_XWID_ERR_XBOW	58
+#define HEART_L4_INT_CPU_BUS_ERR_0	59
+#define HEART_L4_INT_CPU_BUS_ERR_1	60
+#define HEART_L4_INT_CPU_BUS_ERR_2	61
+#define HEART_L4_INT_CPU_BUS_ERR_3	62
+#define HEART_L4_INT_HEART_EXCP		63
+
+extern struct ip30_heart_regs __iomem *heart_regs;
+
+#define heart_read	____raw_readq
+#define heart_write	____raw_writeq
+
+#endif /* __ASM_SGI_HEART_H */
diff --git a/arch/mips/include/asm/sgi/hpc3.h b/arch/mips/include/asm/sgi/hpc3.h
new file mode 100644
index 000000000..c0e3dc029
--- /dev/null
+++ b/arch/mips/include/asm/sgi/hpc3.h
@@ -0,0 +1,317 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * hpc3.h: Definitions for SGI HPC3 controller
+ *
+ * Copyright (C) 1996 David S. Miller
+ * Copyright (C) 1998 Ralf Baechle
+ */
+
+#ifndef _SGI_HPC3_H
+#define _SGI_HPC3_H
+
+#include <linux/types.h>
+#include <asm/page.h>
+
+/* An HPC DMA descriptor. */
+struct hpc_dma_desc {
+	u32 pbuf;	/* physical address of data buffer */
+	u32 cntinfo;	/* counter and info bits */
+#define HPCDMA_EOX	0x80000000 /* last desc in chain for tx */
+#define HPCDMA_EOR	0x80000000 /* last desc in chain for rx */
+#define HPCDMA_EOXP	0x40000000 /* end of packet for tx */
+#define HPCDMA_EORP	0x40000000 /* end of packet for rx */
+#define HPCDMA_XIE	0x20000000 /* irq generated when at end of this desc */
+#define HPCDMA_XIU	0x01000000 /* Tx buffer in use by CPU. */
+#define HPCDMA_EIPC	0x00ff0000 /* SEEQ ethernet special xternal bytecount */
+#define HPCDMA_ETXD	0x00008000 /* set to one by HPC when packet tx'd */
+#define HPCDMA_OWN	0x00004000 /* Denotes ring buffer ownership on rx */
+#define HPCDMA_BCNT	0x00003fff /* size in bytes of this dma buffer */
+
+	u32 pnext;	/* paddr of next hpc_dma_desc if any */
+};
+
+/* The set of regs for each HPC3 PBUS DMA channel. */
+struct hpc3_pbus_dmacregs {
+	volatile u32 pbdma_bptr;	/* pbus dma channel buffer ptr */
+	volatile u32 pbdma_dptr;	/* pbus dma channel desc ptr */
+	u32 _unused0[0x1000/4 - 2];	/* padding */
+	volatile u32 pbdma_ctrl;	/* pbus dma channel control register has
+					 * completely different meaning for read
+					 * compared with write */
+	/* read */
+#define HPC3_PDMACTRL_INT	0x00000001 /* interrupt (cleared after read) */
+#define HPC3_PDMACTRL_ISACT	0x00000002 /* channel active */
+	/* write */
+#define HPC3_PDMACTRL_SEL	0x00000002 /* little endian transfer */
+#define HPC3_PDMACTRL_RCV	0x00000004 /* direction is receive */
+#define HPC3_PDMACTRL_FLSH	0x00000008 /* enable flush for receive DMA */
+#define HPC3_PDMACTRL_ACT	0x00000010 /* start dma transfer */
+#define HPC3_PDMACTRL_LD	0x00000020 /* load enable for ACT */
+#define HPC3_PDMACTRL_RT	0x00000040 /* Use realtime GIO bus servicing */
+#define HPC3_PDMACTRL_HW	0x0000ff00 /* DMA High-water mark */
+#define HPC3_PDMACTRL_FB	0x003f0000 /* Ptr to beginning of fifo */
+#define HPC3_PDMACTRL_FE	0x3f000000 /* Ptr to end of fifo */
+
+	u32 _unused1[0x1000/4 - 1];	/* padding */
+};
+
+/* The HPC3 SCSI registers, this does not include external ones. */
+struct hpc3_scsiregs {
+	volatile u32 cbptr;	/* current dma buffer ptr, diagnostic use only */
+	volatile u32 ndptr;	/* next dma descriptor ptr */
+	u32 _unused0[0x1000/4 - 2];	/* padding */
+	volatile u32 bcd;	/* byte count info */
+#define HPC3_SBCD_BCNTMSK 0x00003fff /* bytes to transfer from/to memory */
+#define HPC3_SBCD_XIE	  0x00004000 /* Send IRQ when done with cur buf */
+#define HPC3_SBCD_EOX	  0x00008000 /* Indicates this is last buf in chain */
+
+	volatile u32 ctrl;    /* control register */
+#define HPC3_SCTRL_IRQ	  0x01 /* IRQ asserted, either dma done or parity */
+#define HPC3_SCTRL_ENDIAN 0x02 /* DMA endian mode, 0=big 1=little */
+#define HPC3_SCTRL_DIR	  0x04 /* DMA direction, 1=dev2mem 0=mem2dev */
+#define HPC3_SCTRL_FLUSH  0x08 /* Tells HPC3 to flush scsi fifos */
+#define HPC3_SCTRL_ACTIVE 0x10 /* SCSI DMA channel is active */
+#define HPC3_SCTRL_AMASK  0x20 /* DMA active inhibits PIO */
+#define HPC3_SCTRL_CRESET 0x40 /* Resets dma channel and external controller */
+#define HPC3_SCTRL_PERR	  0x80 /* Bad parity on HPC3 iface to scsi controller */
+
+	volatile u32 gfptr;	/* current GIO fifo ptr */
+	volatile u32 dfptr;	/* current device fifo ptr */
+	volatile u32 dconfig;	/* DMA configuration register */
+#define HPC3_SDCFG_HCLK 0x00001 /* Enable DMA half clock mode */
+#define HPC3_SDCFG_D1	0x00006 /* Cycles to spend in D1 state */
+#define HPC3_SDCFG_D2	0x00038 /* Cycles to spend in D2 state */
+#define HPC3_SDCFG_D3	0x001c0 /* Cycles to spend in D3 state */
+#define HPC3_SDCFG_HWAT 0x00e00 /* DMA high water mark */
+#define HPC3_SDCFG_HW	0x01000 /* Enable 16-bit halfword DMA accesses to scsi */
+#define HPC3_SDCFG_SWAP 0x02000 /* Byte swap all DMA accesses */
+#define HPC3_SDCFG_EPAR 0x04000 /* Enable parity checking for DMA */
+#define HPC3_SDCFG_POLL 0x08000 /* hd_dreq polarity control */
+#define HPC3_SDCFG_ERLY 0x30000 /* hd_dreq behavior control bits */
+
+	volatile u32 pconfig;	/* PIO configuration register */
+#define HPC3_SPCFG_P3	0x0003 /* Cycles to spend in P3 state */
+#define HPC3_SPCFG_P2W	0x001c /* Cycles to spend in P2 state for writes */
+#define HPC3_SPCFG_P2R	0x01e0 /* Cycles to spend in P2 state for reads */
+#define HPC3_SPCFG_P1	0x0e00 /* Cycles to spend in P1 state */
+#define HPC3_SPCFG_HW	0x1000 /* Enable 16-bit halfword PIO accesses to scsi */
+#define HPC3_SPCFG_SWAP 0x2000 /* Byte swap all PIO accesses */
+#define HPC3_SPCFG_EPAR 0x4000 /* Enable parity checking for PIO */
+#define HPC3_SPCFG_FUJI 0x8000 /* Fujitsu scsi controller mode for faster dma/pio */
+
+	u32 _unused1[0x1000/4 - 6];	/* padding */
+};
+
+/* SEEQ ethernet HPC3 registers, only one seeq per HPC3. */
+struct hpc3_ethregs {
+	/* Receiver registers. */
+	volatile u32 rx_cbptr;	 /* current dma buffer ptr, diagnostic use only */
+	volatile u32 rx_ndptr;	 /* next dma descriptor ptr */
+	u32 _unused0[0x1000/4 - 2];	/* padding */
+	volatile u32 rx_bcd;	/* byte count info */
+#define HPC3_ERXBCD_BCNTMSK 0x00003fff /* bytes to be sent to memory */
+#define HPC3_ERXBCD_XIE	    0x20000000 /* HPC3 interrupts cpu at end of this buf */
+#define HPC3_ERXBCD_EOX	    0x80000000 /* flags this as end of descriptor chain */
+
+	volatile u32 rx_ctrl;	/* control register */
+#define HPC3_ERXCTRL_STAT50 0x0000003f /* Receive status reg bits of Seeq8003 */
+#define HPC3_ERXCTRL_STAT6  0x00000040 /* Rdonly irq status */
+#define HPC3_ERXCTRL_STAT7  0x00000080 /* Rdonlt old/new status bit from Seeq */
+#define HPC3_ERXCTRL_ENDIAN 0x00000100 /* Endian for dma channel, little=1 big=0 */
+#define HPC3_ERXCTRL_ACTIVE 0x00000200 /* Tells if DMA transfer is in progress */
+#define HPC3_ERXCTRL_AMASK  0x00000400 /* Tells if ACTIVE inhibits PIO's to hpc3 */
+#define HPC3_ERXCTRL_RBO    0x00000800 /* Receive buffer overflow if set to 1 */
+
+	volatile u32 rx_gfptr;	/* current GIO fifo ptr */
+	volatile u32 rx_dfptr;	/* current device fifo ptr */
+	u32 _unused1;		/* padding */
+	volatile u32 reset;	/* reset register */
+#define HPC3_ERST_CRESET 0x1	/* Reset dma channel and external controller */
+#define HPC3_ERST_CLRIRQ 0x2	/* Clear channel interrupt */
+#define HPC3_ERST_LBACK	 0x4	/* Enable diagnostic loopback mode of Seeq8003 */
+
+	volatile u32 dconfig;	 /* DMA configuration register */
+#define HPC3_EDCFG_D1	 0x0000f /* Cycles to spend in D1 state for PIO */
+#define HPC3_EDCFG_D2	 0x000f0 /* Cycles to spend in D2 state for PIO */
+#define HPC3_EDCFG_D3	 0x00f00 /* Cycles to spend in D3 state for PIO */
+#define HPC3_EDCFG_WCTRL 0x01000 /* Enable writes of desc into ex ctrl port */
+#define HPC3_EDCFG_FRXDC 0x02000 /* Clear eop stat bits upon rxdc, hw seeq fix */
+#define HPC3_EDCFG_FEOP	 0x04000 /* Bad packet marker timeout enable */
+#define HPC3_EDCFG_FIRQ	 0x08000 /* Another bad packet timeout enable */
+#define HPC3_EDCFG_PTO	 0x30000 /* Programmed timeout value for above two */
+
+	volatile u32 pconfig;	/* PIO configuration register */
+#define HPC3_EPCFG_P1	 0x000f /* Cycles to spend in P1 state for PIO */
+#define HPC3_EPCFG_P2	 0x00f0 /* Cycles to spend in P2 state for PIO */
+#define HPC3_EPCFG_P3	 0x0f00 /* Cycles to spend in P3 state for PIO */
+#define HPC3_EPCFG_TST	 0x1000 /* Diagnostic ram test feature bit */
+
+	u32 _unused2[0x1000/4 - 8];	/* padding */
+
+	/* Transmitter registers. */
+	volatile u32 tx_cbptr;	/* current dma buffer ptr, diagnostic use only */
+	volatile u32 tx_ndptr;	/* next dma descriptor ptr */
+	u32 _unused3[0x1000/4 - 2];	/* padding */
+	volatile u32 tx_bcd;		/* byte count info */
+#define HPC3_ETXBCD_BCNTMSK 0x00003fff	/* bytes to be read from memory */
+#define HPC3_ETXBCD_ESAMP   0x10000000	/* if set, too late to add descriptor */
+#define HPC3_ETXBCD_XIE	    0x20000000	/* Interrupt cpu at end of cur desc */
+#define HPC3_ETXBCD_EOP	    0x40000000	/* Last byte of cur buf is end of packet */
+#define HPC3_ETXBCD_EOX	    0x80000000	/* This buf is the end of desc chain */
+
+	volatile u32 tx_ctrl;		/* control register */
+#define HPC3_ETXCTRL_STAT30 0x0000000f	/* Rdonly copy of seeq tx stat reg */
+#define HPC3_ETXCTRL_STAT4  0x00000010	/* Indicate late collision occurred */
+#define HPC3_ETXCTRL_STAT75 0x000000e0	/* Rdonly irq status from seeq */
+#define HPC3_ETXCTRL_ENDIAN 0x00000100	/* DMA channel endian mode, 1=little 0=big */
+#define HPC3_ETXCTRL_ACTIVE 0x00000200	/* DMA tx channel is active */
+#define HPC3_ETXCTRL_AMASK  0x00000400	/* Indicates ACTIVE inhibits PIO's */
+
+	volatile u32 tx_gfptr;		/* current GIO fifo ptr */
+	volatile u32 tx_dfptr;		/* current device fifo ptr */
+	u32 _unused4[0x1000/4 - 4];	/* padding */
+};
+
+struct hpc3_regs {
+	/* First regs for the PBUS 8 dma channels. */
+	struct hpc3_pbus_dmacregs pbdma[8];
+
+	/* Now the HPC scsi registers, we get two scsi reg sets. */
+	struct hpc3_scsiregs scsi_chan0, scsi_chan1;
+
+	/* The SEEQ hpc3 ethernet dma/control registers. */
+	struct hpc3_ethregs ethregs;
+
+	/* Here are where the hpc3 fifo's can be directly accessed
+	 * via PIO accesses.  Under normal operation we never stick
+	 * our grubby paws in here so it's just padding. */
+	u32 _unused0[0x18000/4];
+
+	/* HPC3 irq status regs.  Due to a peculiar bug you need to
+	 * look at two different register addresses to get at all of
+	 * the status bits.  The first reg can only reliably report
+	 * bits 4:0 of the status, and the second reg can only
+	 * reliably report bits 9:5 of the hpc3 irq status.  I told
+	 * you it was a peculiar bug. ;-)
+	 */
+	volatile u32 istat0;		/* Irq status, only bits <4:0> reliable. */
+#define HPC3_ISTAT_PBIMASK	0x0ff	/* irq bits for pbus devs 0 --> 7 */
+#define HPC3_ISTAT_SC0MASK	0x100	/* irq bit for scsi channel 0 */
+#define HPC3_ISTAT_SC1MASK	0x200	/* irq bit for scsi channel 1 */
+
+	volatile u32 gio_misc;		/* GIO misc control bits. */
+#define HPC3_GIOMISC_ERTIME	0x1	/* Enable external timer real time. */
+#define HPC3_GIOMISC_DENDIAN	0x2	/* dma descriptor endian, 1=lit 0=big */
+
+	u32 eeprom;			/* EEPROM data reg. */
+#define HPC3_EEPROM_EPROT	0x01	/* Protect register enable */
+#define HPC3_EEPROM_CSEL	0x02	/* Chip select */
+#define HPC3_EEPROM_ECLK	0x04	/* EEPROM clock */
+#define HPC3_EEPROM_DATO	0x08	/* Data out */
+#define HPC3_EEPROM_DATI	0x10	/* Data in */
+
+	volatile u32 istat1;		/* Irq status, only bits <9:5> reliable. */
+	volatile u32 bestat;		/* Bus error interrupt status reg. */
+#define HPC3_BESTAT_BLMASK	0x000ff /* Bus lane where bad parity occurred */
+#define HPC3_BESTAT_CTYPE	0x00100 /* Bus cycle type, 0=PIO 1=DMA */
+#define HPC3_BESTAT_PIDSHIFT	9
+#define HPC3_BESTAT_PIDMASK	0x3f700 /* DMA channel parity identifier */
+
+	u32 _unused1[0x14000/4 - 5];	/* padding */
+
+	/* Now direct PIO per-HPC3 peripheral access to external regs. */
+	volatile u32 scsi0_ext[256];	/* SCSI channel 0 external regs */
+	u32 _unused2[0x7c00/4];
+	volatile u32 scsi1_ext[256];	/* SCSI channel 1 external regs */
+	u32 _unused3[0x7c00/4];
+	volatile u32 eth_ext[320];	/* Ethernet external registers */
+	u32 _unused4[0x3b00/4];
+
+	/* Per-peripheral device external registers and DMA/PIO control. */
+	volatile u32 pbus_extregs[16][256];
+	volatile u32 pbus_dmacfg[8][128];
+	/* Cycles to spend in D3 for reads */
+#define HPC3_DMACFG_D3R_MASK		0x00000001
+#define HPC3_DMACFG_D3R_SHIFT		0
+	/* Cycles to spend in D4 for reads */
+#define HPC3_DMACFG_D4R_MASK		0x0000001e
+#define HPC3_DMACFG_D4R_SHIFT		1
+	/* Cycles to spend in D5 for reads */
+#define HPC3_DMACFG_D5R_MASK		0x000001e0
+#define HPC3_DMACFG_D5R_SHIFT		5
+	/* Cycles to spend in D3 for writes */
+#define HPC3_DMACFG_D3W_MASK		0x00000200
+#define HPC3_DMACFG_D3W_SHIFT		9
+	/* Cycles to spend in D4 for writes */
+#define HPC3_DMACFG_D4W_MASK		0x00003c00
+#define HPC3_DMACFG_D4W_SHIFT		10
+	/* Cycles to spend in D5 for writes */
+#define HPC3_DMACFG_D5W_MASK		0x0003c000
+#define HPC3_DMACFG_D5W_SHIFT		14
+	/* Enable 16-bit DMA access mode */
+#define HPC3_DMACFG_DS16		0x00040000
+	/* Places halfwords on high 16 bits of bus */
+#define HPC3_DMACFG_EVENHI		0x00080000
+	/* Make this device real time */
+#define HPC3_DMACFG_RTIME		0x00200000
+	/* 5 bit burst count for DMA device */
+#define HPC3_DMACFG_BURST_MASK		0x07c00000
+#define HPC3_DMACFG_BURST_SHIFT 22
+	/* Use live pbus_dreq unsynchronized signal */
+#define HPC3_DMACFG_DRQLIVE		0x08000000
+	volatile u32 pbus_piocfg[16][64];
+	/* Cycles to spend in P2 state for reads */
+#define HPC3_PIOCFG_P2R_MASK		0x00001
+#define HPC3_PIOCFG_P2R_SHIFT		0
+	/* Cycles to spend in P3 state for reads */
+#define HPC3_PIOCFG_P3R_MASK		0x0001e
+#define HPC3_PIOCFG_P3R_SHIFT		1
+	/* Cycles to spend in P4 state for reads */
+#define HPC3_PIOCFG_P4R_MASK		0x001e0
+#define HPC3_PIOCFG_P4R_SHIFT		5
+	/* Cycles to spend in P2 state for writes */
+#define HPC3_PIOCFG_P2W_MASK		0x00200
+#define HPC3_PIOCFG_P2W_SHIFT		9
+	/* Cycles to spend in P3 state for writes */
+#define HPC3_PIOCFG_P3W_MASK		0x03c00
+#define HPC3_PIOCFG_P3W_SHIFT		10
+	/* Cycles to spend in P4 state for writes */
+#define HPC3_PIOCFG_P4W_MASK		0x3c000
+#define HPC3_PIOCFG_P4W_SHIFT		14
+	/* Enable 16-bit PIO accesses */
+#define HPC3_PIOCFG_DS16		0x40000
+	/* Place even address bits in bits <15:8> */
+#define HPC3_PIOCFG_EVENHI		0x80000
+
+	/* PBUS PROM control regs. */
+	volatile u32 pbus_promwe;	/* PROM write enable register */
+#define HPC3_PROM_WENAB 0x1	/* Enable writes to the PROM */
+
+	u32 _unused5[0x0800/4 - 1];
+	volatile u32 pbus_promswap;	/* Chip select swap reg */
+#define HPC3_PROM_SWAP	0x1	/* invert GIO addr bit to select prom0 or prom1 */
+
+	u32 _unused6[0x0800/4 - 1];
+	volatile u32 pbus_gout; /* PROM general purpose output reg */
+#define HPC3_PROM_STAT	0x1	/* General purpose status bit in gout */
+
+	u32 _unused7[0x1000/4 - 1];
+	volatile u32 rtcregs[14];	/* Dallas clock registers */
+	u32 _unused8[50];
+	volatile u32 bbram[8192-50-14]; /* Battery backed ram */
+};
+
+/*
+ * It is possible to have two HPC3's within the address space on
+ * one machine, though only having one is more likely on an Indy.
+ */
+extern struct hpc3_regs *hpc3c0, *hpc3c1;
+#define HPC3_CHIP0_BASE		0x1fb80000	/* physical */
+#define HPC3_CHIP1_BASE		0x1fb00000	/* physical */
+
+extern void sgihpc_init(void);
+
+#endif /* _SGI_HPC3_H */
diff --git a/arch/mips/include/asm/sgi/ioc.h b/arch/mips/include/asm/sgi/ioc.h
new file mode 100644
index 000000000..53c6b1ca6
--- /dev/null
+++ b/arch/mips/include/asm/sgi/ioc.h
@@ -0,0 +1,200 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * ioc.h: Definitions for SGI I/O Controller
+ *
+ * Copyright (C) 1996 David S. Miller
+ * Copyright (C) 1997, 1998, 1999, 2000 Ralf Baechle
+ * Copyright (C) 2001, 2003 Ladislav Michl
+ */
+
+#ifndef _SGI_IOC_H
+#define _SGI_IOC_H
+
+#include <linux/types.h>
+#include <asm/sgi/pi1.h>
+
+/*
+ * All registers are 8-bit wide aligned on 32-bit boundary. Bad things
+ * happen if you try word access them. You have been warned.
+ */
+
+struct sgioc_uart_regs {
+	u8 _ctrl1[3];
+	volatile u8 ctrl1;
+	u8 _data1[3];
+	volatile u8 data1;
+	u8 _ctrl2[3];
+	volatile u8 ctrl2;
+	u8 _data2[3];
+	volatile u8 data2;
+};
+
+struct sgioc_keyb_regs {
+	u8 _data[3];
+	volatile u8 data;
+	u8 _command[3];
+	volatile u8 command;
+};
+
+struct sgint_regs {
+	u8 _istat0[3];
+	volatile u8 istat0;		/* Interrupt status zero */
+#define SGINT_ISTAT0_FFULL	0x01
+#define SGINT_ISTAT0_SCSI0	0x02
+#define SGINT_ISTAT0_SCSI1	0x04
+#define SGINT_ISTAT0_ENET	0x08
+#define SGINT_ISTAT0_GFXDMA	0x10
+#define SGINT_ISTAT0_PPORT	0x20
+#define SGINT_ISTAT0_HPC2	0x40
+#define SGINT_ISTAT0_LIO2	0x80
+	u8 _imask0[3];
+	volatile u8 imask0;		/* Interrupt mask zero */
+	u8 _istat1[3];
+	volatile u8 istat1;		/* Interrupt status one */
+#define SGINT_ISTAT1_ISDNI	0x01
+#define SGINT_ISTAT1_PWR	0x02
+#define SGINT_ISTAT1_ISDNH	0x04
+#define SGINT_ISTAT1_LIO3	0x08
+#define SGINT_ISTAT1_HPC3	0x10
+#define SGINT_ISTAT1_AFAIL	0x20
+#define SGINT_ISTAT1_VIDEO	0x40
+#define SGINT_ISTAT1_GIO2	0x80
+	u8 _imask1[3];
+	volatile u8 imask1;		/* Interrupt mask one */
+	u8 _vmeistat[3];
+	volatile u8 vmeistat;		/* VME interrupt status */
+	u8 _cmeimask0[3];
+	volatile u8 cmeimask0;		/* VME interrupt mask zero */
+	u8 _cmeimask1[3];
+	volatile u8 cmeimask1;		/* VME interrupt mask one */
+	u8 _cmepol[3];
+	volatile u8 cmepol;		/* VME polarity */
+	u8 _tclear[3];
+	volatile u8 tclear;
+	u8 _errstat[3];
+	volatile u8 errstat;	/* Error status reg, reserved on INT2 */
+	u32 _unused0[2];
+	u8 _tcnt0[3];
+	volatile u8 tcnt0;		/* counter 0 */
+	u8 _tcnt1[3];
+	volatile u8 tcnt1;		/* counter 1 */
+	u8 _tcnt2[3];
+	volatile u8 tcnt2;		/* counter 2 */
+	u8 _tcword[3];
+	volatile u8 tcword;		/* control word */
+#define SGINT_TCWORD_BCD	0x01	/* Use BCD mode for counters */
+#define SGINT_TCWORD_MMASK	0x0e	/* Mode bitmask. */
+#define SGINT_TCWORD_MITC	0x00	/* IRQ on terminal count (doesn't work) */
+#define SGINT_TCWORD_MOS	0x02	/* One-shot IRQ mode. */
+#define SGINT_TCWORD_MRGEN	0x04	/* Normal rate generation */
+#define SGINT_TCWORD_MSWGEN	0x06	/* Square wave generator mode */
+#define SGINT_TCWORD_MSWST	0x08	/* Software strobe */
+#define SGINT_TCWORD_MHWST	0x0a	/* Hardware strobe */
+#define SGINT_TCWORD_CMASK	0x30	/* Command mask */
+#define SGINT_TCWORD_CLAT	0x00	/* Latch command */
+#define SGINT_TCWORD_CLSB	0x10	/* LSB read/write */
+#define SGINT_TCWORD_CMSB	0x20	/* MSB read/write */
+#define SGINT_TCWORD_CALL	0x30	/* Full counter read/write */
+#define SGINT_TCWORD_CNT0	0x00	/* Select counter zero */
+#define SGINT_TCWORD_CNT1	0x40	/* Select counter one */
+#define SGINT_TCWORD_CNT2	0x80	/* Select counter two */
+#define SGINT_TCWORD_CRBCK	0xc0	/* Readback command */
+};
+
+/*
+ * The timer is the good old 8254.  Unlike in PCs it's clocked at exactly 1MHz
+ */
+#define SGINT_TIMER_CLOCK	1000000
+
+/*
+ * This is the constant we're using for calibrating the counter.
+ */
+#define SGINT_TCSAMP_COUNTER	((SGINT_TIMER_CLOCK / HZ) + 255)
+
+/* We need software copies of these because they are write only. */
+extern u8 sgi_ioc_reset, sgi_ioc_write;
+
+struct sgioc_regs {
+	struct pi1_regs pport;
+	u32 _unused0[2];
+	struct sgioc_uart_regs uart;
+	struct sgioc_keyb_regs kbdmouse;
+	u8 _gcsel[3];
+	volatile u8 gcsel;
+	u8 _genctrl[3];
+	volatile u8 genctrl;
+	u8 _panel[3];
+	volatile u8 panel;
+#define SGIOC_PANEL_POWERON	0x01
+#define SGIOC_PANEL_POWERINTR	0x02
+#define SGIOC_PANEL_VOLDNINTR	0x10
+#define SGIOC_PANEL_VOLDNHOLD	0x20
+#define SGIOC_PANEL_VOLUPINTR	0x40
+#define SGIOC_PANEL_VOLUPHOLD	0x80
+	u32 _unused1;
+	u8 _sysid[3];
+	volatile u8 sysid;
+#define SGIOC_SYSID_FULLHOUSE	0x01
+#define SGIOC_SYSID_BOARDREV(x) (((x) & 0x1e) >> 1)
+#define SGIOC_SYSID_CHIPREV(x)	(((x) & 0xe0) >> 5)
+	u32 _unused2;
+	u8 _read[3];
+	volatile u8 read;
+	u32 _unused3;
+	u8 _dmasel[3];
+	volatile u8 dmasel;
+#define SGIOC_DMASEL_SCLK10MHZ	0x00	/* use 10MHZ serial clock */
+#define SGIOC_DMASEL_ISDNB	0x01	/* enable isdn B */
+#define SGIOC_DMASEL_ISDNA	0x02	/* enable isdn A */
+#define SGIOC_DMASEL_PPORT	0x04	/* use parallel DMA */
+#define SGIOC_DMASEL_SCLK667MHZ 0x10	/* use 6.67MHZ serial clock */
+#define SGIOC_DMASEL_SCLKEXT	0x20	/* use external serial clock */
+	u32 _unused4;
+	u8 _reset[3];
+	volatile u8 reset;
+#define SGIOC_RESET_PPORT	0x01	/* 0=parport reset, 1=nornal */
+#define SGIOC_RESET_KBDMOUSE	0x02	/* 0=kbdmouse reset, 1=normal */
+#define SGIOC_RESET_EISA	0x04	/* 0=eisa reset, 1=normal */
+#define SGIOC_RESET_ISDN	0x08	/* 0=isdn reset, 1=normal */
+#define SGIOC_RESET_LC0OFF	0x10	/* guiness: turn led off (red, else green) */
+#define SGIOC_RESET_LC1OFF	0x20	/* guiness: turn led off (green, else amber) */
+	u32 _unused5;
+	u8 _write[3];
+	volatile u8 write;
+#define SGIOC_WRITE_NTHRESH	0x01	/* use 4.5db threshold */
+#define SGIOC_WRITE_TPSPEED	0x02	/* use 100ohm TP speed */
+#define SGIOC_WRITE_EPSEL	0x04	/* force cable mode: 1=AUI 0=TP */
+#define SGIOC_WRITE_EASEL	0x08	/* 1=autoselect 0=manual cable selection */
+#define SGIOC_WRITE_U1AMODE	0x10	/* 1=PC 0=MAC UART mode */
+#define SGIOC_WRITE_U0AMODE	0x20	/* 1=PC 0=MAC UART mode */
+#define SGIOC_WRITE_MLO		0x40	/* 1=4.75V 0=+5V */
+#define SGIOC_WRITE_MHI		0x80	/* 1=5.25V 0=+5V */
+	u32 _unused6;
+	struct sgint_regs int3;
+	u32 _unused7[16];
+	volatile u32 extio;		/* FullHouse only */
+#define EXTIO_S0_IRQ_3		0x8000	/* S0: vid.vsync */
+#define EXTIO_S0_IRQ_2		0x4000	/* S0: gfx.fifofull */
+#define EXTIO_S0_IRQ_1		0x2000	/* S0: gfx.int */
+#define EXTIO_S0_RETRACE	0x1000
+#define EXTIO_SG_IRQ_3		0x0800	/* SG: vid.vsync */
+#define EXTIO_SG_IRQ_2		0x0400	/* SG: gfx.fifofull */
+#define EXTIO_SG_IRQ_1		0x0200	/* SG: gfx.int */
+#define EXTIO_SG_RETRACE	0x0100
+#define EXTIO_GIO_33MHZ		0x0080
+#define EXTIO_EISA_BUSERR	0x0040
+#define EXTIO_MC_BUSERR		0x0020
+#define EXTIO_HPC3_BUSERR	0x0010
+#define EXTIO_S0_STAT_1		0x0008
+#define EXTIO_S0_STAT_0		0x0004
+#define EXTIO_SG_STAT_1		0x0002
+#define EXTIO_SG_STAT_0		0x0001
+};
+
+extern struct sgioc_regs *sgioc;
+extern struct sgint_regs *sgint;
+
+#endif
diff --git a/arch/mips/include/asm/sgi/ip22.h b/arch/mips/include/asm/sgi/ip22.h
new file mode 100644
index 000000000..87ec9eaa0
--- /dev/null
+++ b/arch/mips/include/asm/sgi/ip22.h
@@ -0,0 +1,80 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * ip22.h: Definitions for SGI IP22 machines
+ *
+ * Copyright (C) 1996 David S. Miller
+ * Copyright (C) 1997, 1998, 1999, 2000 Ralf Baechle
+ */
+
+#ifndef _SGI_IP22_H
+#define _SGI_IP22_H
+
+/*
+ * These are the virtual IRQ numbers, we divide all IRQ's into
+ * 'spaces', the 'space' determines where and how to enable/disable
+ * that particular IRQ on an SGI machine. HPC DMA and MC DMA interrupts
+ * are not supported this way. Driver is supposed to allocate HPC/MC
+ * interrupt as shareable and then look to proper status bit (see
+ * HAL2 driver). This will prevent many complications, trust me ;-)
+ */
+
+#include <irq.h>
+#include <asm/sgi/ioc.h>
+
+#define SGINT_EISA	0	/* 16 EISA irq levels (Indigo2) */
+#define SGINT_CPU	MIPS_CPU_IRQ_BASE	/* MIPS CPU define 8 interrupt sources */
+#define SGINT_LOCAL0	(SGINT_CPU+8)	/* 8 local0 irq levels */
+#define SGINT_LOCAL1	(SGINT_CPU+16)	/* 8 local1 irq levels */
+#define SGINT_LOCAL2	(SGINT_CPU+24)	/* 8 local2 vectored irq levels */
+#define SGINT_LOCAL3	(SGINT_CPU+32)	/* 8 local3 vectored irq levels */
+#define SGINT_END	(SGINT_CPU+40)	/* End of 'spaces' */
+
+/*
+ * Individual interrupt definitions for the Indy and Indigo2
+ */
+
+#define SGI_SOFT_0_IRQ	SGINT_CPU + 0
+#define SGI_SOFT_1_IRQ	SGINT_CPU + 1
+#define SGI_LOCAL_0_IRQ SGINT_CPU + 2
+#define SGI_LOCAL_1_IRQ SGINT_CPU + 3
+#define SGI_8254_0_IRQ	SGINT_CPU + 4
+#define SGI_8254_1_IRQ	SGINT_CPU + 5
+#define SGI_BUSERR_IRQ	SGINT_CPU + 6
+#define SGI_TIMER_IRQ	SGINT_CPU + 7
+
+#define SGI_FIFO_IRQ	SGINT_LOCAL0 + 0	/* FIFO full */
+#define SGI_GIO_0_IRQ	SGI_FIFO_IRQ		/* GIO-0 */
+#define SGI_WD93_0_IRQ	SGINT_LOCAL0 + 1	/* 1st onboard WD93 */
+#define SGI_WD93_1_IRQ	SGINT_LOCAL0 + 2	/* 2nd onboard WD93 */
+#define SGI_ENET_IRQ	SGINT_LOCAL0 + 3	/* onboard ethernet */
+#define SGI_MCDMA_IRQ	SGINT_LOCAL0 + 4	/* MC DMA done */
+#define SGI_PARPORT_IRQ SGINT_LOCAL0 + 5	/* Parallel port */
+#define SGI_GIO_1_IRQ	SGINT_LOCAL0 + 6	/* GE / GIO-1 / 2nd-HPC */
+#define SGI_MAP_0_IRQ	SGINT_LOCAL0 + 7	/* Mappable interrupt 0 */
+
+#define SGI_GPL0_IRQ	SGINT_LOCAL1 + 0	/* General Purpose LOCAL1_N<0> */
+#define SGI_PANEL_IRQ	SGINT_LOCAL1 + 1	/* front panel */
+#define SGI_GPL2_IRQ	SGINT_LOCAL1 + 2	/* General Purpose LOCAL1_N<2> */
+#define SGI_MAP_1_IRQ	SGINT_LOCAL1 + 3	/* Mappable interrupt 1 */
+#define SGI_HPCDMA_IRQ	SGINT_LOCAL1 + 4	/* HPC DMA done */
+#define SGI_ACFAIL_IRQ	SGINT_LOCAL1 + 5	/* AC fail */
+#define SGI_VINO_IRQ	SGINT_LOCAL1 + 6	/* Indy VINO */
+#define SGI_GIO_2_IRQ	SGINT_LOCAL1 + 7	/* Vert retrace / GIO-2 */
+
+/* Mapped interrupts. These interrupts may be mapped to either 0, or 1 */
+#define SGI_VERT_IRQ	SGINT_LOCAL2 + 0	/* INT3: newport vertical status */
+#define SGI_EISA_IRQ	SGINT_LOCAL2 + 3	/* EISA interrupts */
+#define SGI_KEYBD_IRQ	SGINT_LOCAL2 + 4	/* keyboard */
+#define SGI_SERIAL_IRQ	SGINT_LOCAL2 + 5	/* onboard serial */
+#define SGI_GIOEXP0_IRQ	(SGINT_LOCAL2 + 6)	/* Indy GIO EXP0 */
+#define SGI_GIOEXP1_IRQ	(SGINT_LOCAL2 + 7)	/* Indy GIO EXP1 */
+
+#define ip22_is_fullhouse()	(sgioc->sysid & SGIOC_SYSID_FULLHOUSE)
+
+extern unsigned short ip22_eeprom_read(unsigned int *ctrl, int reg);
+extern unsigned short ip22_nvram_read(int reg);
+
+#endif
diff --git a/arch/mips/include/asm/sgi/mc.h b/arch/mips/include/asm/sgi/mc.h
new file mode 100644
index 000000000..3a070cec9
--- /dev/null
+++ b/arch/mips/include/asm/sgi/mc.h
@@ -0,0 +1,231 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * mc.h: Definitions for SGI Memory Controller
+ *
+ * Copyright (C) 1996 David S. Miller
+ * Copyright (C) 1999 Ralf Baechle
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ */
+
+#ifndef _SGI_MC_H
+#define _SGI_MC_H
+
+struct sgimc_regs {
+	u32 _unused0;
+	volatile u32 cpuctrl0;	/* CPU control register 0, readwrite */
+#define SGIMC_CCTRL0_REFS	0x0000000f /* REFS mask */
+#define SGIMC_CCTRL0_EREFRESH	0x00000010 /* Memory refresh enable */
+#define SGIMC_CCTRL0_EPERRGIO	0x00000020 /* GIO parity error enable */
+#define SGIMC_CCTRL0_EPERRMEM	0x00000040 /* Main mem parity error enable */
+#define SGIMC_CCTRL0_EPERRCPU	0x00000080 /* CPU bus parity error enable */
+#define SGIMC_CCTRL0_WDOG	0x00000100 /* Watchdog timer enable */
+#define SGIMC_CCTRL0_SYSINIT	0x00000200 /* System init bit */
+#define SGIMC_CCTRL0_GFXRESET	0x00000400 /* Graphics interface reset */
+#define SGIMC_CCTRL0_EISALOCK	0x00000800 /* Lock CPU from memory for EISA */
+#define SGIMC_CCTRL0_EPERRSCMD	0x00001000 /* SysCMD bus parity error enable */
+#define SGIMC_CCTRL0_IENAB	0x00002000 /* Allow interrupts from MC */
+#define SGIMC_CCTRL0_ESNOOP	0x00004000 /* Snooping I/O enable */
+#define SGIMC_CCTRL0_EPROMWR	0x00008000 /* Prom writes from cpu enable */
+#define SGIMC_CCTRL0_WRESETPMEM 0x00010000 /* Perform warm reset, preserves mem */
+#define SGIMC_CCTRL0_LENDIAN	0x00020000 /* Put MC in little-endian mode */
+#define SGIMC_CCTRL0_WRESETDMEM 0x00040000 /* Warm reset, destroys mem contents */
+#define SGIMC_CCTRL0_CMEMBADPAR 0x02000000 /* Generate bad perr from cpu to mem */
+#define SGIMC_CCTRL0_R4KNOCHKPARR 0x04000000 /* Don't chk parity on mem data reads */
+#define SGIMC_CCTRL0_GIOBTOB	0x08000000 /* Allow GIO back to back writes */
+	u32 _unused1;
+	volatile u32 cpuctrl1;	/* CPU control register 1, readwrite */
+#define SGIMC_CCTRL1_EGIOTIMEO	0x00000010 /* GIO bus timeout enable */
+#define SGIMC_CCTRL1_FIXEDEHPC	0x00001000 /* Fixed HPC endianness */
+#define SGIMC_CCTRL1_LITTLEHPC	0x00002000 /* Little endian HPC */
+#define SGIMC_CCTRL1_FIXEDEEXP0 0x00004000 /* Fixed EXP0 endianness */
+#define SGIMC_CCTRL1_LITTLEEXP0 0x00008000 /* Little endian EXP0 */
+#define SGIMC_CCTRL1_FIXEDEEXP1 0x00010000 /* Fixed EXP1 endianness */
+#define SGIMC_CCTRL1_LITTLEEXP1 0x00020000 /* Little endian EXP1 */
+
+	u32 _unused2;
+	volatile u32 watchdogt; /* Watchdog reg rdonly, write clears */
+
+	u32 _unused3;
+	volatile u32 systemid;	/* MC system ID register, readonly */
+#define SGIMC_SYSID_MASKREV	0x0000000f /* Revision of MC controller */
+#define SGIMC_SYSID_EPRESENT	0x00000010 /* Indicates presence of EISA bus */
+
+	u32 _unused4[3];
+	volatile u32 divider;	/* Divider reg for RPSS */
+
+	u32 _unused5;
+	u32 eeprom;		/* EEPROM byte reg for r4k */
+#define SGIMC_EEPROM_PRE	0x00000001 /* eeprom chip PRE pin assertion */
+#define SGIMC_EEPROM_CSEL	0x00000002 /* Active high, eeprom chip select */
+#define SGIMC_EEPROM_SECLOCK	0x00000004 /* EEPROM serial clock */
+#define SGIMC_EEPROM_SDATAO	0x00000008 /* Serial EEPROM data-out */
+#define SGIMC_EEPROM_SDATAI	0x00000010 /* Serial EEPROM data-in */
+
+	u32 _unused6[3];
+	volatile u32 rcntpre;	/* Preload refresh counter */
+
+	u32 _unused7;
+	volatile u32 rcounter;	/* Readonly refresh counter */
+
+	u32 _unused8[13];
+	volatile u32 giopar;	/* Parameter word for GIO64 */
+#define SGIMC_GIOPAR_HPC64	0x00000001 /* HPC talks to GIO using 64-bits */
+#define SGIMC_GIOPAR_GFX64	0x00000002 /* GFX talks to GIO using 64-bits */
+#define SGIMC_GIOPAR_EXP064	0x00000004 /* EXP(slot0) talks using 64-bits */
+#define SGIMC_GIOPAR_EXP164	0x00000008 /* EXP(slot1) talks using 64-bits */
+#define SGIMC_GIOPAR_EISA64	0x00000010 /* EISA bus talks 64-bits to GIO */
+#define SGIMC_GIOPAR_HPC264	0x00000020 /* 2nd HPX talks 64-bits to GIO */
+#define SGIMC_GIOPAR_RTIMEGFX	0x00000040 /* GFX device has realtime attr */
+#define SGIMC_GIOPAR_RTIMEEXP0	0x00000080 /* EXP(slot0) has realtime attr */
+#define SGIMC_GIOPAR_RTIMEEXP1	0x00000100 /* EXP(slot1) has realtime attr */
+#define SGIMC_GIOPAR_MASTEREISA 0x00000200 /* EISA bus can act as bus master */
+#define SGIMC_GIOPAR_ONEBUS	0x00000400 /* Exists one GIO64 pipelined bus */
+#define SGIMC_GIOPAR_MASTERGFX	0x00000800 /* GFX can act as a bus master */
+#define SGIMC_GIOPAR_MASTEREXP0 0x00001000 /* EXP(slot0) can bus master */
+#define SGIMC_GIOPAR_MASTEREXP1 0x00002000 /* EXP(slot1) can bus master */
+#define SGIMC_GIOPAR_PLINEEXP0	0x00004000 /* EXP(slot0) has pipeline attr */
+#define SGIMC_GIOPAR_PLINEEXP1	0x00008000 /* EXP(slot1) has pipeline attr */
+
+	u32 _unused9;
+	volatile u32 cputp;	/* CPU bus arb time period */
+
+	u32 _unused10[3];
+	volatile u32 lbursttp;	/* Time period for long bursts */
+
+	/* MC chip can drive up to 4 bank 4 SIMMs each. All SIMMs in bank must
+	 * be the same size. The size encoding for supported SIMMs is bellow */
+	u32 _unused11[9];
+	volatile u32 mconfig0;	/* Memory config register zero */
+	u32 _unused12;
+	volatile u32 mconfig1;	/* Memory config register one */
+#define SGIMC_MCONFIG_BASEADDR	0x000000ff /* Base address of bank*/
+#define SGIMC_MCONFIG_RMASK	0x00001f00 /* Ram config bitmask */
+#define SGIMC_MCONFIG_BVALID	0x00002000 /* Bank is valid */
+#define SGIMC_MCONFIG_SBANKS	0x00004000 /* Number of subbanks */
+
+	u32 _unused13;
+	volatile u32 cmacc;	   /* Mem access config for CPU */
+	u32 _unused14;
+	volatile u32 gmacc;	   /* Mem access config for GIO */
+
+	/* This define applies to both cmacc and gmacc registers above. */
+#define SGIMC_MACC_ALIASBIG	0x20000000 /* 512MB home for alias */
+
+	/* Error address/status regs from GIO and CPU perspectives. */
+	u32 _unused15;
+	volatile u32 cerr;	/* Error address reg for CPU */
+	u32 _unused16;
+	volatile u32 cstat;	/* Status reg for CPU */
+#define SGIMC_CSTAT_RD		0x00000100 /* read parity error */
+#define SGIMC_CSTAT_PAR		0x00000200 /* CPU parity error */
+#define SGIMC_CSTAT_ADDR	0x00000400 /* memory bus error bad addr */
+#define SGIMC_CSTAT_SYSAD_PAR	0x00000800 /* sysad parity error */
+#define SGIMC_CSTAT_SYSCMD_PAR	0x00001000 /* syscmd parity error */
+#define SGIMC_CSTAT_BAD_DATA	0x00002000 /* bad data identifier */
+#define SGIMC_CSTAT_PAR_MASK	0x00001f00 /* parity error mask */
+#define SGIMC_CSTAT_RD_PAR	(SGIMC_CSTAT_RD | SGIMC_CSTAT_PAR)
+
+	u32 _unused17;
+	volatile u32 gerr;	/* Error address reg for GIO */
+	u32 _unused18;
+	volatile u32 gstat;	/* Status reg for GIO */
+#define SGIMC_GSTAT_RD		0x00000100 /* read parity error */
+#define SGIMC_GSTAT_WR		0x00000200 /* write parity error */
+#define SGIMC_GSTAT_TIME	0x00000400 /* GIO bus timed out */
+#define SGIMC_GSTAT_PROM	0x00000800 /* write to PROM when PROM_EN not set */
+#define SGIMC_GSTAT_ADDR	0x00001000 /* parity error on addr cycle */
+#define SGIMC_GSTAT_BC		0x00002000 /* parity error on byte count cycle */
+#define SGIMC_GSTAT_PIO_RD	0x00004000 /* read data parity on pio */
+#define SGIMC_GSTAT_PIO_WR	0x00008000 /* write data parity on pio */
+
+	/* Special hard bus locking registers. */
+	u32 _unused19;
+	volatile u32 syssembit;		/* Uni-bit system semaphore */
+	u32 _unused20;
+	volatile u32 mlock;		/* Global GIO memory access lock */
+	u32 _unused21;
+	volatile u32 elock;		/* Locks EISA from GIO accesses */
+
+	/* GIO dma control registers. */
+	u32 _unused22[15];
+	volatile u32 gio_dma_trans;	/* DMA mask to translation GIO addrs */
+	u32 _unused23;
+	volatile u32 gio_dma_sbits;	/* DMA GIO addr substitution bits */
+	u32 _unused24;
+	volatile u32 dma_intr_cause;	/* DMA IRQ cause indicator bits */
+	u32 _unused25;
+	volatile u32 dma_ctrl;		/* Main DMA control reg */
+
+	/* DMA TLB entry 0 */
+	u32 _unused26[5];
+	volatile u32 dtlb_hi0;
+	u32 _unused27;
+	volatile u32 dtlb_lo0;
+
+	/* DMA TLB entry 1 */
+	u32 _unused28;
+	volatile u32 dtlb_hi1;
+	u32 _unused29;
+	volatile u32 dtlb_lo1;
+
+	/* DMA TLB entry 2 */
+	u32 _unused30;
+	volatile u32 dtlb_hi2;
+	u32 _unused31;
+	volatile u32 dtlb_lo2;
+
+	/* DMA TLB entry 3 */
+	u32 _unused32;
+	volatile u32 dtlb_hi3;
+	u32 _unused33;
+	volatile u32 dtlb_lo3;
+
+	u32 _unused34[0x0392];
+
+	u32 _unused35;
+	volatile u32 rpsscounter;	/* Chirps at 100ns */
+
+	u32 _unused36[0x1000/4-2*4];
+
+	u32 _unused37;
+	volatile u32 maddronly;		/* Address DMA goes at */
+	u32 _unused38;
+	volatile u32 maddrpdeflts;	/* Same as above, plus set defaults */
+	u32 _unused39;
+	volatile u32 dmasz;		/* DMA count */
+	u32 _unused40;
+	volatile u32 ssize;		/* DMA stride size */
+	u32 _unused41;
+	volatile u32 gmaddronly;	/* Set GIO DMA but don't start trans */
+	u32 _unused42;
+	volatile u32 dmaddnpgo;		/* Set GIO DMA addr + start transfer */
+	u32 _unused43;
+	volatile u32 dmamode;		/* DMA mode config bit settings */
+	u32 _unused44;
+	volatile u32 dmaccount;		/* Zoom and byte count for DMA */
+	u32 _unused45;
+	volatile u32 dmastart;		/* Pedal to the metal. */
+	u32 _unused46;
+	volatile u32 dmarunning;	/* DMA op is in progress */
+	u32 _unused47;
+	volatile u32 maddrdefstart;	/* Set dma addr, defaults, and kick it */
+};
+
+extern struct sgimc_regs *sgimc;
+#define SGIMC_BASE		0x1fa00000	/* physical */
+
+/* Base location of the two ram banks found in IP2[0268] machines. */
+#define SGIMC_SEG0_BADDR	0x08000000
+#define SGIMC_SEG1_BADDR	0x20000000
+
+/* Maximum size of the above banks are per machine. */
+#define SGIMC_SEG0_SIZE_ALL		0x10000000 /* 256MB */
+#define SGIMC_SEG1_SIZE_IP20_IP22	0x08000000 /* 128MB */
+#define SGIMC_SEG1_SIZE_IP26_IP28	0x20000000 /* 512MB */
+
+extern void sgimc_init(void);
+
+#endif /* _SGI_MC_H */
diff --git a/arch/mips/include/asm/sgi/pi1.h b/arch/mips/include/asm/sgi/pi1.h
new file mode 100644
index 000000000..88b814ef3
--- /dev/null
+++ b/arch/mips/include/asm/sgi/pi1.h
@@ -0,0 +1,72 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * pi1.h: Definitions for SGI PI1 parallel port
+ */
+
+#ifndef _SGI_PI1_H
+#define _SGI_PI1_H
+
+struct pi1_regs {
+	u8 _data[3];
+	volatile u8 data;
+	u8 _ctrl[3];
+	volatile u8 ctrl;
+#define PI1_CTRL_STROBE_N	0x01
+#define PI1_CTRL_AFD_N		0x02
+#define PI1_CTRL_INIT_N		0x04
+#define PI1_CTRL_SLIN_N		0x08
+#define PI1_CTRL_IRQ_ENA	0x10
+#define PI1_CTRL_DIR		0x20
+#define PI1_CTRL_SEL		0x40
+	u8 _status[3];
+	volatile u8 status;
+#define PI1_STAT_DEVID		0x03	/* bits 0-1 */
+#define PI1_STAT_NOINK		0x04	/* SGI MODE only */
+#define PI1_STAT_ERROR		0x08
+#define PI1_STAT_ONLINE		0x10
+#define PI1_STAT_PE		0x20
+#define PI1_STAT_ACK		0x40
+#define PI1_STAT_BUSY		0x80
+	u8 _dmactrl[3];
+	volatile u8 dmactrl;
+#define PI1_DMACTRL_FIFO_EMPTY	0x01	/* fifo empty R/O */
+#define PI1_DMACTRL_ABORT	0x02	/* reset DMA and internal fifo W/O */
+#define PI1_DMACTRL_STDMODE	0x00	/* bits 2-3 */
+#define PI1_DMACTRL_SGIMODE	0x04	/* bits 2-3 */
+#define PI1_DMACTRL_RICOHMODE	0x08	/* bits 2-3 */
+#define PI1_DMACTRL_HPMODE	0x0c	/* bits 2-3 */
+#define PI1_DMACTRL_BLKMODE	0x10	/* block mode */
+#define PI1_DMACTRL_FIFO_CLEAR	0x20	/* clear fifo W/O */
+#define PI1_DMACTRL_READ	0x40	/* read */
+#define PI1_DMACTRL_RUN		0x80	/* pedal to the metal */
+	u8 _intstat[3];
+	volatile u8 intstat;
+#define PI1_INTSTAT_ACK		0x04
+#define PI1_INTSTAT_FEMPTY	0x08
+#define PI1_INTSTAT_NOINK	0x10
+#define PI1_INTSTAT_ONLINE	0x20
+#define PI1_INTSTAT_ERR		0x40
+#define PI1_INTSTAT_PE		0x80
+	u8 _intmask[3];
+	volatile u8 intmask;		/* enabled low, reset high*/
+#define PI1_INTMASK_ACK		0x04
+#define PI1_INTMASK_FIFO_EMPTY	0x08
+#define PI1_INTMASK_NOINK	0x10
+#define PI1_INTMASK_ONLINE	0x20
+#define PI1_INTMASK_ERR		0x40
+#define PI1_INTMASK_PE		0x80
+	u8 _timer1[3];
+	volatile u8 timer1;
+#define PI1_TIME1		0x27
+	u8 _timer2[3];
+	volatile u8 timer2;
+#define PI1_TIME2		0x13
+	u8 _timer3[3];
+	volatile u8 timer3;
+#define PI1_TIME3		0x10
+	u8 _timer4[3];
+	volatile u8 timer4;
+#define PI1_TIME4		0x00
+};
+
+#endif
diff --git a/arch/mips/include/asm/sgi/seeq.h b/arch/mips/include/asm/sgi/seeq.h
new file mode 100644
index 000000000..af0ffd768
--- /dev/null
+++ b/arch/mips/include/asm/sgi/seeq.h
@@ -0,0 +1,21 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2007 by Ralf Baechle
+ */
+#ifndef __ASM_SGI_SEEQ_H
+#define __ASM_SGI_SEEQ_H
+
+#include <linux/if_ether.h>
+
+#include <asm/sgi/hpc3.h>
+
+struct sgiseeq_platform_data {
+	struct hpc3_regs *hpc;
+	unsigned int irq;
+	unsigned char mac[ETH_ALEN];
+};
+
+#endif /* __ASM_SGI_SEEQ_H */
diff --git a/arch/mips/include/asm/sgi/wd.h b/arch/mips/include/asm/sgi/wd.h
new file mode 100644
index 000000000..0d6c3a4da
--- /dev/null
+++ b/arch/mips/include/asm/sgi/wd.h
@@ -0,0 +1,20 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2007 by Ralf Baechle
+ */
+#ifndef __ASM_SGI_WD_H
+#define __ASM_SGI_WD_H
+
+#include <asm/sgi/hpc3.h>
+
+struct sgiwd93_platform_data {
+	unsigned int unit;
+	unsigned int irq;
+	struct hpc3_scsiregs *hregs;
+	unsigned char *wdregs;
+};
+
+#endif /* __ASM_SGI_WD_H */
diff --git a/arch/mips/include/asm/sgialib.h b/arch/mips/include/asm/sgialib.h
new file mode 100644
index 000000000..80f900417
--- /dev/null
+++ b/arch/mips/include/asm/sgialib.h
@@ -0,0 +1,61 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * SGI ARCS firmware interface library for the Linux kernel.
+ *
+ * Copyright (C) 1996 David S. Miller (davem@davemloft.net)
+ * Copyright (C) 2001, 2002 Ralf Baechle (ralf@gnu.org)
+ */
+#ifndef _ASM_SGIALIB_H
+#define _ASM_SGIALIB_H
+
+#include <linux/compiler.h>
+#include <asm/sgiarcs.h>
+
+extern struct linux_romvec *romvec;
+
+extern int prom_flags;
+
+#define PROM_FLAG_ARCS			1
+#define PROM_FLAG_USE_AS_CONSOLE	2
+#define PROM_FLAG_DONT_FREE_TEMP	4
+
+/* Simple char-by-char console I/O. */
+extern char prom_getchar(void);
+
+/* Get next memory descriptor after CURR, returns first descriptor
+ * in chain is CURR is NULL.
+ */
+extern struct linux_mdesc *prom_getmdesc(struct linux_mdesc *curr);
+#define PROM_NULL_MDESC	  ((struct linux_mdesc *) 0)
+
+/* Called by prom_init to setup the physical memory pmemblock
+ * array.
+ */
+extern void prom_meminit(void);
+
+/* PROM device tree library routines. */
+#define PROM_NULL_COMPONENT ((pcomponent *) 0)
+
+/* This is called at prom_init time to identify the
+ * ARC architecture we are running on
+ */
+extern void prom_identify_arch(void);
+
+/* Environment variable routines. */
+extern PCHAR ArcGetEnvironmentVariable(PCHAR name);
+
+/* ARCS command line parsing. */
+extern void prom_init_cmdline(int argc, LONG *argv);
+
+/* File operations. */
+extern LONG ArcRead(ULONG fd, PVOID buf, ULONG num, PULONG cnt);
+extern LONG ArcWrite(ULONG fd, PVOID buf, ULONG num, PULONG cnt);
+
+/* Misc. routines. */
+extern VOID ArcEnterInteractiveMode(VOID) __noreturn;
+extern DISPLAY_STATUS *ArcGetDisplayStatus(ULONG FileID);
+
+#endif /* _ASM_SGIALIB_H */
diff --git a/arch/mips/include/asm/sgiarcs.h b/arch/mips/include/asm/sgiarcs.h
new file mode 100644
index 000000000..e1512cab1
--- /dev/null
+++ b/arch/mips/include/asm/sgiarcs.h
@@ -0,0 +1,505 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * ARC firmware interface defines.
+ *
+ * Copyright (C) 1996 David S. Miller (davem@davemloft.net)
+ * Copyright (C) 1999, 2001 Ralf Baechle (ralf@gnu.org)
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_SGIARCS_H
+#define _ASM_SGIARCS_H
+
+#include <linux/kernel.h>
+
+#include <asm/types.h>
+#include <asm/fw/arc/types.h>
+
+/* Various ARCS error codes. */
+#define PROM_ESUCCESS			0x00
+#define PROM_E2BIG			0x01
+#define PROM_EACCESS			0x02
+#define PROM_EAGAIN			0x03
+#define PROM_EBADF			0x04
+#define PROM_EBUSY			0x05
+#define PROM_EFAULT			0x06
+#define PROM_EINVAL			0x07
+#define PROM_EIO			0x08
+#define PROM_EISDIR			0x09
+#define PROM_EMFILE			0x0a
+#define PROM_EMLINK			0x0b
+#define PROM_ENAMETOOLONG		0x0c
+#define PROM_ENODEV			0x0d
+#define PROM_ENOENT			0x0e
+#define PROM_ENOEXEC			0x0f
+#define PROM_ENOMEM			0x10
+#define PROM_ENOSPC			0x11
+#define PROM_ENOTDIR			0x12
+#define PROM_ENOTTY			0x13
+#define PROM_ENXIO			0x14
+#define PROM_EROFS			0x15
+/* SGI ARCS specific errno's. */
+#define PROM_EADDRNOTAVAIL		0x1f
+#define PROM_ETIMEDOUT			0x20
+#define PROM_ECONNABORTED		0x21
+#define PROM_ENOCONNECT			0x22
+
+/* Device classes, types, and identifiers for prom
+ * device inventory queries.
+ */
+enum linux_devclass {
+	system, processor, cache, adapter, controller, peripheral, memory
+};
+
+enum linux_devtypes {
+	/* Generic stuff. */
+	Arc, Cpu, Fpu,
+
+	/* Primary insn and data caches. */
+	picache, pdcache,
+
+	/* Secondary insn, data, and combined caches. */
+	sicache, sdcache, sccache,
+
+	memdev, eisa_adapter, tc_adapter, scsi_adapter, dti_adapter,
+	multifunc_adapter, dsk_controller, tp_controller, cdrom_controller,
+	worm_controller, serial_controller, net_controller, disp_controller,
+	parallel_controller, ptr_controller, kbd_controller, audio_controller,
+	misc_controller, disk_peripheral, flpy_peripheral, tp_peripheral,
+	modem_peripheral, monitor_peripheral, printer_peripheral,
+	ptr_peripheral, kbd_peripheral, term_peripheral, line_peripheral,
+	net_peripheral, misc_peripheral, anon
+};
+
+enum linux_identifier {
+	bogus, ronly, removable, consin, consout, input, output
+};
+
+/* A prom device tree component. */
+struct linux_component {
+	enum linux_devclass	class;	/* node class */
+	enum linux_devtypes	type;	/* node type */
+	enum linux_identifier	iflags; /* node flags */
+	USHORT			vers;	/* node version */
+	USHORT			rev;	/* node revision */
+	ULONG			key;	/* completely magic */
+	ULONG			amask;	/* XXX affinity mask??? */
+	ULONG			cdsize; /* size of configuration data */
+	ULONG			ilen;	/* length of string identifier */
+	_PULONG			iname;	/* string identifier */
+};
+typedef struct linux_component pcomponent;
+
+struct linux_sysid {
+	char vend[8], prod[8];
+};
+
+/* ARCS prom memory descriptors. */
+enum arcs_memtypes {
+	arcs_eblock,  /* exception block */
+	arcs_rvpage,  /* ARCS romvec page */
+	arcs_fcontig, /* Contiguous and free */
+	arcs_free,    /* Generic free memory */
+	arcs_bmem,    /* Borken memory, don't use */
+	arcs_prog,    /* A loaded program resides here */
+	arcs_atmp,    /* ARCS temporary storage area, wish Sparc OpenBoot told this */
+	arcs_aperm,   /* ARCS permanent storage... */
+};
+
+/* ARC has slightly different types than ARCS */
+enum arc_memtypes {
+	arc_eblock,  /* exception block */
+	arc_rvpage,  /* romvec page */
+	arc_free,    /* Generic free memory */
+	arc_bmem,    /* Borken memory, don't use */
+	arc_prog,    /* A loaded program resides here */
+	arc_atmp,    /* temporary storage area */
+	arc_aperm,   /* permanent storage */
+	arc_fcontig, /* Contiguous and free */
+};
+
+union linux_memtypes {
+    enum arcs_memtypes arcs;
+    enum arc_memtypes arc;
+};
+
+struct linux_mdesc {
+	union linux_memtypes type;
+	ULONG base;
+	ULONG pages;
+};
+
+/* Time of day descriptor. */
+struct linux_tinfo {
+	unsigned short yr;
+	unsigned short mnth;
+	unsigned short day;
+	unsigned short hr;
+	unsigned short min;
+	unsigned short sec;
+	unsigned short msec;
+};
+
+/* ARCS virtual dirents. */
+struct linux_vdirent {
+	ULONG namelen;
+	unsigned char attr;
+	char fname[32]; /* XXX empirical, should be a define */
+};
+
+/* Other stuff for files. */
+enum linux_omode {
+	rdonly, wronly, rdwr, wronly_creat, rdwr_creat,
+	wronly_ssede, rdwr_ssede, dirent, dirent_creat
+};
+
+enum linux_seekmode {
+	absolute, relative
+};
+
+enum linux_mountops {
+	media_load, media_unload
+};
+
+/* This prom has a bolixed design. */
+struct linux_bigint {
+#ifdef __MIPSEL__
+	u32 lo;
+	s32 hi;
+#else /* !(__MIPSEL__) */
+	s32 hi;
+	u32 lo;
+#endif
+};
+
+struct linux_finfo {
+	struct linux_bigint   begin;
+	struct linux_bigint   end;
+	struct linux_bigint   cur;
+	enum linux_devtypes   dtype;
+	unsigned long	      namelen;
+	unsigned char	      attr;
+	char		      name[32]; /* XXX empirical, should be define */
+};
+
+/* This describes the vector containing function pointers to the ARC
+   firmware functions.	*/
+struct linux_romvec {
+	LONG	load;			/* Load an executable image. */
+	LONG	invoke;			/* Invoke a standalong image. */
+	LONG	exec;			/* Load and begin execution of a
+					   standalone image. */
+	LONG	halt;			/* Halt the machine. */
+	LONG	pdown;			/* Power down the machine. */
+	LONG	restart;		/* XXX soft reset??? */
+	LONG	reboot;			/* Reboot the machine. */
+	LONG	imode;			/* Enter PROM interactive mode. */
+	LONG	_unused1;		/* Was ReturnFromMain(). */
+
+	/* PROM device tree interface. */
+	LONG	next_component;
+	LONG	child_component;
+	LONG	parent_component;
+	LONG	component_data;
+	LONG	child_add;
+	LONG	comp_del;
+	LONG	component_by_path;
+
+	/* Misc. stuff. */
+	LONG	cfg_save;
+	LONG	get_sysid;
+
+	/* Probing for memory. */
+	LONG	get_mdesc;
+	LONG	_unused2;		/* was Signal() */
+
+	LONG	get_tinfo;
+	LONG	get_rtime;
+
+	/* File type operations. */
+	LONG	get_vdirent;
+	LONG	open;
+	LONG	close;
+	LONG	read;
+	LONG	get_rstatus;
+	LONG	write;
+	LONG	seek;
+	LONG	mount;
+
+	/* Dealing with firmware environment variables. */
+	LONG	get_evar;
+	LONG	set_evar;
+
+	LONG	get_finfo;
+	LONG	set_finfo;
+
+	/* Miscellaneous. */
+	LONG	cache_flush;
+	LONG	TestUnicodeCharacter;		/* ARC; not sure if ARCS too */
+	LONG	GetDisplayStatus;
+};
+
+/* The SGI ARCS parameter block is in a fixed location for standalone
+ * programs to access PROM facilities easily.
+ */
+typedef struct _SYSTEM_PARAMETER_BLOCK {
+	ULONG			magic;		/* magic cookie */
+#define PROMBLOCK_MAGIC	     0x53435241
+
+	ULONG			len;		/* length of parm block */
+	USHORT			ver;		/* ARCS firmware version */
+	USHORT			rev;		/* ARCS firmware revision */
+	_PLONG			rs_block;	/* Restart block. */
+	_PLONG			dbg_block;	/* Debug block. */
+	_PLONG			gevect;		/* XXX General vector??? */
+	_PLONG			utlbvect;	/* XXX UTLB vector??? */
+	ULONG			rveclen;	/* Size of romvec struct. */
+	_PVOID			romvec;		/* Function interface. */
+	ULONG			pveclen;	/* Length of private vector. */
+	_PVOID			pvector;	/* Private vector. */
+	ULONG			adap_cnt;	/* Adapter count. */
+	ULONG			adap_typ0;	/* First adapter type. */
+	ULONG			adap_vcnt0;	/* Adapter 0 vector count. */
+	_PVOID			adap_vector;	/* Adapter 0 vector ptr. */
+	ULONG			adap_typ1;	/* Second adapter type. */
+	ULONG			adap_vcnt1;	/* Adapter 1 vector count. */
+	_PVOID			adap_vector1;	/* Adapter 1 vector ptr. */
+	/* More adapter vectors go here... */
+} SYSTEM_PARAMETER_BLOCK, *PSYSTEM_PARAMETER_BLOCK;
+
+#define PROMBLOCK ((PSYSTEM_PARAMETER_BLOCK) (int)0xA0001000)
+#define ROMVECTOR ((struct linux_romvec *) (long)(PROMBLOCK)->romvec)
+
+/* Cache layout parameter block. */
+union linux_cache_key {
+	struct param {
+#ifdef __MIPSEL__
+		unsigned short size;
+		unsigned char lsize;
+		unsigned char bsize;
+#else /* !(__MIPSEL__) */
+		unsigned char bsize;
+		unsigned char lsize;
+		unsigned short size;
+#endif
+	} info;
+	unsigned long allinfo;
+};
+
+/* Configuration data. */
+struct linux_cdata {
+	char *name;
+	int mlen;
+	enum linux_devtypes type;
+};
+
+/* Common SGI ARCS firmware file descriptors. */
+#define SGIPROM_STDIN	  0
+#define SGIPROM_STDOUT	  1
+
+/* Common SGI ARCS firmware file types. */
+#define SGIPROM_ROFILE	  0x01	/* read-only file */
+#define SGIPROM_HFILE	  0x02	/* hidden file */
+#define SGIPROM_SFILE	  0x04	/* System file */
+#define SGIPROM_AFILE	  0x08	/* Archive file */
+#define SGIPROM_DFILE	  0x10	/* Directory file */
+#define SGIPROM_DELFILE	  0x20	/* Deleted file */
+
+/* SGI ARCS boot record information. */
+struct sgi_partition {
+	unsigned char flag;
+#define SGIPART_UNUSED 0x00
+#define SGIPART_ACTIVE 0x80
+
+	unsigned char shead, ssect, scyl; /* unused */
+	unsigned char systype; /* OS type, Irix or NT */
+	unsigned char ehead, esect, ecyl; /* unused */
+	unsigned char rsect0, rsect1, rsect2, rsect3;
+	unsigned char tsect0, tsect1, tsect2, tsect3;
+};
+
+#define SGIBBLOCK_MAGIC	  0xaa55
+#define SGIBBLOCK_MAXPART 0x0004
+
+struct sgi_bootblock {
+	unsigned char _unused[446];
+	struct sgi_partition partitions[SGIBBLOCK_MAXPART];
+	unsigned short magic;
+};
+
+/* BIOS parameter block. */
+struct sgi_bparm_block {
+	unsigned short bytes_sect;    /* bytes per sector */
+	unsigned char  sect_clust;    /* sectors per cluster */
+	unsigned short sect_resv;     /* reserved sectors */
+	unsigned char  nfats;	      /* # of allocation tables */
+	unsigned short nroot_dirents; /* # of root directory entries */
+	unsigned short sect_volume;   /* sectors in volume */
+	unsigned char  media_type;    /* media descriptor */
+	unsigned short sect_fat;      /* sectors per allocation table */
+	unsigned short sect_track;    /* sectors per track */
+	unsigned short nheads;	      /* # of heads */
+	unsigned short nhsects;	      /* # of hidden sectors */
+};
+
+struct sgi_bsector {
+	unsigned char	jmpinfo[3];
+	unsigned char	manuf_name[8];
+	struct sgi_bparm_block info;
+};
+
+/* Debugging block used with SGI symmon symbolic debugger. */
+#define SMB_DEBUG_MAGIC	  0xfeeddead
+struct linux_smonblock {
+	unsigned long	magic;
+	void		(*handler)(void);  /* Breakpoint routine. */
+	unsigned long	dtable_base;	   /* Base addr of dbg table. */
+	int		(*printf)(const char *fmt, ...);
+	unsigned long	btable_base;	   /* Breakpoint table. */
+	unsigned long	mpflushreqs;	   /* SMP cache flush request list. */
+	unsigned long	ntab;		   /* Name table. */
+	unsigned long	stab;		   /* Symbol table. */
+	int		smax;		   /* Max # of symbols. */
+};
+
+/*
+ * Macros for calling a 32-bit ARC implementation from 64-bit code
+ */
+
+#if defined(CONFIG_64BIT) && defined(CONFIG_FW_ARC32)
+
+extern long call_o32(long vec, void *stack, ...);
+
+extern u64 o32_stk[4096];
+#define O32_STK	(&o32_stk[ARRAY_SIZE(o32_stk)])
+
+#define ARC_CALL0(dest)							\
+({	long __res;							\
+	long __vec = (long) romvec->dest;				\
+	__res = call_o32(__vec, O32_STK);				\
+	__res;								\
+})
+
+#define ARC_CALL1(dest, a1)						\
+({	long __res;							\
+	int  __a1 = (int) (long) (a1);					\
+	long __vec = (long) romvec->dest;				\
+	__res = call_o32(__vec, O32_STK, __a1);				\
+	__res;								\
+})
+
+#define ARC_CALL2(dest, a1, a2)						\
+({	long __res;							\
+	int  __a1 = (int) (long) (a1);					\
+	int  __a2 = (int) (long) (a2);					\
+	long __vec = (long) romvec->dest;				\
+	__res = call_o32(__vec, O32_STK, __a1, __a2);			\
+	__res;								\
+})
+
+#define ARC_CALL3(dest, a1, a2, a3)					\
+({	long __res;							\
+	int  __a1 = (int) (long) (a1);					\
+	int  __a2 = (int) (long) (a2);					\
+	int  __a3 = (int) (long) (a3);					\
+	long __vec = (long) romvec->dest;				\
+	__res = call_o32(__vec, O32_STK, __a1, __a2, __a3);		\
+	__res;								\
+})
+
+#define ARC_CALL4(dest, a1, a2, a3, a4)					\
+({	long __res;							\
+	int  __a1 = (int) (long) (a1);					\
+	int  __a2 = (int) (long) (a2);					\
+	int  __a3 = (int) (long) (a3);					\
+	int  __a4 = (int) (long) (a4);					\
+	long __vec = (long) romvec->dest;				\
+	__res = call_o32(__vec, O32_STK, __a1, __a2, __a3, __a4);	\
+	__res;								\
+})
+
+#define ARC_CALL5(dest, a1, a2, a3, a4, a5)				\
+({	long __res;							\
+	int  __a1 = (int) (long) (a1);					\
+	int  __a2 = (int) (long) (a2);					\
+	int  __a3 = (int) (long) (a3);					\
+	int  __a4 = (int) (long) (a4);					\
+	int  __a5 = (int) (long) (a5);					\
+	long __vec = (long) romvec->dest;				\
+	__res = call_o32(__vec, O32_STK, __a1, __a2, __a3, __a4, __a5);	\
+	__res;								\
+})
+
+#endif /* defined(CONFIG_64BIT) && defined(CONFIG_FW_ARC32) */
+
+#if (defined(CONFIG_32BIT) && defined(CONFIG_FW_ARC32)) ||		\
+    (defined(CONFIG_64BIT) && defined(CONFIG_FW_ARC64))
+
+#define ARC_CALL0(dest)							\
+({	long __res;							\
+	long (*__vec)(void) = (void *) romvec->dest;			\
+									\
+	__res = __vec();						\
+	__res;								\
+})
+
+#define ARC_CALL1(dest, a1)						\
+({	long __res;							\
+	long __a1 = (long) (a1);					\
+	long (*__vec)(long) = (void *) romvec->dest;			\
+									\
+	__res = __vec(__a1);						\
+	__res;								\
+})
+
+#define ARC_CALL2(dest, a1, a2)						\
+({	long __res;							\
+	long __a1 = (long) (a1);					\
+	long __a2 = (long) (a2);					\
+	long (*__vec)(long, long) = (void *) romvec->dest;		\
+									\
+	__res = __vec(__a1, __a2);					\
+	__res;								\
+})
+
+#define ARC_CALL3(dest, a1, a2, a3)					\
+({	long __res;							\
+	long __a1 = (long) (a1);					\
+	long __a2 = (long) (a2);					\
+	long __a3 = (long) (a3);					\
+	long (*__vec)(long, long, long) = (void *) romvec->dest;	\
+									\
+	__res = __vec(__a1, __a2, __a3);				\
+	__res;								\
+})
+
+#define ARC_CALL4(dest, a1, a2, a3, a4)					\
+({	long __res;							\
+	long __a1 = (long) (a1);					\
+	long __a2 = (long) (a2);					\
+	long __a3 = (long) (a3);					\
+	long __a4 = (long) (a4);					\
+	long (*__vec)(long, long, long, long) = (void *) romvec->dest;	\
+									\
+	__res = __vec(__a1, __a2, __a3, __a4);				\
+	__res;								\
+})
+
+#define ARC_CALL5(dest, a1, a2, a3, a4, a5)				\
+({	long __res;							\
+	long __a1 = (long) (a1);					\
+	long __a2 = (long) (a2);					\
+	long __a3 = (long) (a3);					\
+	long __a4 = (long) (a4);					\
+	long __a5 = (long) (a5);					\
+	long (*__vec)(long, long, long, long, long);			\
+	__vec = (void *) romvec->dest;					\
+									\
+	__res = __vec(__a1, __a2, __a3, __a4, __a5);			\
+	__res;								\
+})
+#endif /* both kernel and ARC either 32-bit or 64-bit */
+
+#endif /* _ASM_SGIARCS_H */
diff --git a/arch/mips/include/asm/shmparam.h b/arch/mips/include/asm/shmparam.h
new file mode 100644
index 000000000..324d04042
--- /dev/null
+++ b/arch/mips/include/asm/shmparam.h
@@ -0,0 +1,13 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#ifndef _ASM_SHMPARAM_H
+#define _ASM_SHMPARAM_H
+
+#define __ARCH_FORCE_SHMLBA	1
+
+#define SHMLBA 0x40000			/* attach addr a multiple of this */
+
+#endif /* _ASM_SHMPARAM_H */
diff --git a/arch/mips/include/asm/sibyte/bcm1480_int.h b/arch/mips/include/asm/sibyte/bcm1480_int.h
new file mode 100644
index 000000000..18cf4b105
--- /dev/null
+++ b/arch/mips/include/asm/sibyte/bcm1480_int.h
@@ -0,0 +1,299 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*  *********************************************************************
+    *  BCM1280/BCM1480 Board Support Package
+    *
+    *  Interrupt Mapper definitions		File: bcm1480_int.h
+    *
+    *  This module contains constants for manipulating the
+    *  BCM1255/BCM1280/BCM1455/BCM1480's interrupt mapper and
+    *  definitions for the interrupt sources.
+    *
+    *  BCM1480 specification level: 1X55_1X80-UM100-D4 (11/24/03)
+    *
+    *********************************************************************
+    *
+    *  Copyright 2000,2001,2002,2003
+    *  Broadcom Corporation. All rights reserved.
+    *
+    ********************************************************************* */
+
+
+#ifndef _BCM1480_INT_H
+#define _BCM1480_INT_H
+
+#include <asm/sibyte/sb1250_defs.h>
+
+/*  *********************************************************************
+    *  Interrupt Mapper Constants
+    ********************************************************************* */
+
+/*
+ * The interrupt mapper deals with 128-bit logical registers that are
+ * implemented as pairs of 64-bit registers, with the "low" 64 bits in
+ * a register that has an address 0x1000 higher(!) than the
+ * corresponding "high" register.
+ *
+ * For appropriate registers, bit 0 of the "high" register is a
+ * cascade bit that summarizes (as a bit-OR) the 64 bits of the "low"
+ * register.
+ */
+
+/*
+ * This entire file uses _BCM1480_ in all the symbols because it is
+ * entirely BCM1480 specific.
+ */
+
+/*
+ * Interrupt sources (Table 22)
+ */
+
+#define K_BCM1480_INT_SOURCES		    128
+
+#define _BCM1480_INT_HIGH(k)   (k)
+#define _BCM1480_INT_LOW(k)    ((k)+64)
+
+#define K_BCM1480_INT_ADDR_TRAP		    _BCM1480_INT_HIGH(1)
+#define K_BCM1480_INT_GPIO_0		    _BCM1480_INT_HIGH(4)
+#define K_BCM1480_INT_GPIO_1		    _BCM1480_INT_HIGH(5)
+#define K_BCM1480_INT_GPIO_2		    _BCM1480_INT_HIGH(6)
+#define K_BCM1480_INT_GPIO_3		    _BCM1480_INT_HIGH(7)
+#define K_BCM1480_INT_PCI_INTA		    _BCM1480_INT_HIGH(8)
+#define K_BCM1480_INT_PCI_INTB		    _BCM1480_INT_HIGH(9)
+#define K_BCM1480_INT_PCI_INTC		    _BCM1480_INT_HIGH(10)
+#define K_BCM1480_INT_PCI_INTD		    _BCM1480_INT_HIGH(11)
+#define K_BCM1480_INT_CYCLE_CP0		    _BCM1480_INT_HIGH(12)
+#define K_BCM1480_INT_CYCLE_CP1		    _BCM1480_INT_HIGH(13)
+#define K_BCM1480_INT_CYCLE_CP2		    _BCM1480_INT_HIGH(14)
+#define K_BCM1480_INT_CYCLE_CP3		    _BCM1480_INT_HIGH(15)
+#define K_BCM1480_INT_TIMER_0		    _BCM1480_INT_HIGH(20)
+#define K_BCM1480_INT_TIMER_1		    _BCM1480_INT_HIGH(21)
+#define K_BCM1480_INT_TIMER_2		    _BCM1480_INT_HIGH(22)
+#define K_BCM1480_INT_TIMER_3		    _BCM1480_INT_HIGH(23)
+#define K_BCM1480_INT_DM_CH_0		    _BCM1480_INT_HIGH(28)
+#define K_BCM1480_INT_DM_CH_1		    _BCM1480_INT_HIGH(29)
+#define K_BCM1480_INT_DM_CH_2		    _BCM1480_INT_HIGH(30)
+#define K_BCM1480_INT_DM_CH_3		    _BCM1480_INT_HIGH(31)
+#define K_BCM1480_INT_MAC_0		    _BCM1480_INT_HIGH(36)
+#define K_BCM1480_INT_MAC_0_CH1		    _BCM1480_INT_HIGH(37)
+#define K_BCM1480_INT_MAC_1		    _BCM1480_INT_HIGH(38)
+#define K_BCM1480_INT_MAC_1_CH1		    _BCM1480_INT_HIGH(39)
+#define K_BCM1480_INT_MAC_2		    _BCM1480_INT_HIGH(40)
+#define K_BCM1480_INT_MAC_2_CH1		    _BCM1480_INT_HIGH(41)
+#define K_BCM1480_INT_MAC_3		    _BCM1480_INT_HIGH(42)
+#define K_BCM1480_INT_MAC_3_CH1		    _BCM1480_INT_HIGH(43)
+#define K_BCM1480_INT_PMI_LOW		    _BCM1480_INT_HIGH(52)
+#define K_BCM1480_INT_PMI_HIGH		    _BCM1480_INT_HIGH(53)
+#define K_BCM1480_INT_PMO_LOW		    _BCM1480_INT_HIGH(54)
+#define K_BCM1480_INT_PMO_HIGH		    _BCM1480_INT_HIGH(55)
+#define K_BCM1480_INT_MBOX_0_0		    _BCM1480_INT_HIGH(56)
+#define K_BCM1480_INT_MBOX_0_1		    _BCM1480_INT_HIGH(57)
+#define K_BCM1480_INT_MBOX_0_2		    _BCM1480_INT_HIGH(58)
+#define K_BCM1480_INT_MBOX_0_3		    _BCM1480_INT_HIGH(59)
+#define K_BCM1480_INT_MBOX_1_0		    _BCM1480_INT_HIGH(60)
+#define K_BCM1480_INT_MBOX_1_1		    _BCM1480_INT_HIGH(61)
+#define K_BCM1480_INT_MBOX_1_2		    _BCM1480_INT_HIGH(62)
+#define K_BCM1480_INT_MBOX_1_3		    _BCM1480_INT_HIGH(63)
+
+#define K_BCM1480_INT_BAD_ECC		    _BCM1480_INT_LOW(1)
+#define K_BCM1480_INT_COR_ECC		    _BCM1480_INT_LOW(2)
+#define K_BCM1480_INT_IO_BUS		    _BCM1480_INT_LOW(3)
+#define K_BCM1480_INT_PERF_CNT		    _BCM1480_INT_LOW(4)
+#define K_BCM1480_INT_SW_PERF_CNT	    _BCM1480_INT_LOW(5)
+#define K_BCM1480_INT_TRACE_FREEZE	    _BCM1480_INT_LOW(6)
+#define K_BCM1480_INT_SW_TRACE_FREEZE	    _BCM1480_INT_LOW(7)
+#define K_BCM1480_INT_WATCHDOG_TIMER_0	    _BCM1480_INT_LOW(8)
+#define K_BCM1480_INT_WATCHDOG_TIMER_1	    _BCM1480_INT_LOW(9)
+#define K_BCM1480_INT_WATCHDOG_TIMER_2	    _BCM1480_INT_LOW(10)
+#define K_BCM1480_INT_WATCHDOG_TIMER_3	    _BCM1480_INT_LOW(11)
+#define K_BCM1480_INT_PCI_ERROR		    _BCM1480_INT_LOW(16)
+#define K_BCM1480_INT_PCI_RESET		    _BCM1480_INT_LOW(17)
+#define K_BCM1480_INT_NODE_CONTROLLER	    _BCM1480_INT_LOW(18)
+#define K_BCM1480_INT_HOST_BRIDGE	    _BCM1480_INT_LOW(19)
+#define K_BCM1480_INT_PORT_0_FATAL	    _BCM1480_INT_LOW(20)
+#define K_BCM1480_INT_PORT_0_NONFATAL	    _BCM1480_INT_LOW(21)
+#define K_BCM1480_INT_PORT_1_FATAL	    _BCM1480_INT_LOW(22)
+#define K_BCM1480_INT_PORT_1_NONFATAL	    _BCM1480_INT_LOW(23)
+#define K_BCM1480_INT_PORT_2_FATAL	    _BCM1480_INT_LOW(24)
+#define K_BCM1480_INT_PORT_2_NONFATAL	    _BCM1480_INT_LOW(25)
+#define K_BCM1480_INT_LDT_SMI		    _BCM1480_INT_LOW(32)
+#define K_BCM1480_INT_LDT_NMI		    _BCM1480_INT_LOW(33)
+#define K_BCM1480_INT_LDT_INIT		    _BCM1480_INT_LOW(34)
+#define K_BCM1480_INT_LDT_STARTUP	    _BCM1480_INT_LOW(35)
+#define K_BCM1480_INT_LDT_EXT		    _BCM1480_INT_LOW(36)
+#define K_BCM1480_INT_SMB_0		    _BCM1480_INT_LOW(40)
+#define K_BCM1480_INT_SMB_1		    _BCM1480_INT_LOW(41)
+#define K_BCM1480_INT_PCMCIA		    _BCM1480_INT_LOW(42)
+#define K_BCM1480_INT_UART_0		    _BCM1480_INT_LOW(44)
+#define K_BCM1480_INT_UART_1		    _BCM1480_INT_LOW(45)
+#define K_BCM1480_INT_UART_2		    _BCM1480_INT_LOW(46)
+#define K_BCM1480_INT_UART_3		    _BCM1480_INT_LOW(47)
+#define K_BCM1480_INT_GPIO_4		    _BCM1480_INT_LOW(52)
+#define K_BCM1480_INT_GPIO_5		    _BCM1480_INT_LOW(53)
+#define K_BCM1480_INT_GPIO_6		    _BCM1480_INT_LOW(54)
+#define K_BCM1480_INT_GPIO_7		    _BCM1480_INT_LOW(55)
+#define K_BCM1480_INT_GPIO_8		    _BCM1480_INT_LOW(56)
+#define K_BCM1480_INT_GPIO_9		    _BCM1480_INT_LOW(57)
+#define K_BCM1480_INT_GPIO_10		    _BCM1480_INT_LOW(58)
+#define K_BCM1480_INT_GPIO_11		    _BCM1480_INT_LOW(59)
+#define K_BCM1480_INT_GPIO_12		    _BCM1480_INT_LOW(60)
+#define K_BCM1480_INT_GPIO_13		    _BCM1480_INT_LOW(61)
+#define K_BCM1480_INT_GPIO_14		    _BCM1480_INT_LOW(62)
+#define K_BCM1480_INT_GPIO_15		    _BCM1480_INT_LOW(63)
+
+/*
+ * Mask values for each interrupt
+ */
+
+#define _BCM1480_INT_MASK(w, n)		     _SB_MAKEMASK(w, ((n) & 0x3F))
+#define _BCM1480_INT_MASK1(n)		    _SB_MAKEMASK1(((n) & 0x3F))
+#define _BCM1480_INT_OFFSET(n)		    (((n) & 0x40) << 6)
+
+#define M_BCM1480_INT_CASCADE		    _BCM1480_INT_MASK1(_BCM1480_INT_HIGH(0))
+
+#define M_BCM1480_INT_ADDR_TRAP		    _BCM1480_INT_MASK1(K_BCM1480_INT_ADDR_TRAP)
+#define M_BCM1480_INT_GPIO_0		    _BCM1480_INT_MASK1(K_BCM1480_INT_GPIO_0)
+#define M_BCM1480_INT_GPIO_1		    _BCM1480_INT_MASK1(K_BCM1480_INT_GPIO_1)
+#define M_BCM1480_INT_GPIO_2		    _BCM1480_INT_MASK1(K_BCM1480_INT_GPIO_2)
+#define M_BCM1480_INT_GPIO_3		    _BCM1480_INT_MASK1(K_BCM1480_INT_GPIO_3)
+#define M_BCM1480_INT_PCI_INTA		    _BCM1480_INT_MASK1(K_BCM1480_INT_PCI_INTA)
+#define M_BCM1480_INT_PCI_INTB		    _BCM1480_INT_MASK1(K_BCM1480_INT_PCI_INTB)
+#define M_BCM1480_INT_PCI_INTC		    _BCM1480_INT_MASK1(K_BCM1480_INT_PCI_INTC)
+#define M_BCM1480_INT_PCI_INTD		    _BCM1480_INT_MASK1(K_BCM1480_INT_PCI_INTD)
+#define M_BCM1480_INT_CYCLE_CP0		    _BCM1480_INT_MASK1(K_BCM1480_INT_CYCLE_CP0)
+#define M_BCM1480_INT_CYCLE_CP1		    _BCM1480_INT_MASK1(K_BCM1480_INT_CYCLE_CP1)
+#define M_BCM1480_INT_CYCLE_CP2		    _BCM1480_INT_MASK1(K_BCM1480_INT_CYCLE_CP2)
+#define M_BCM1480_INT_CYCLE_CP3		    _BCM1480_INT_MASK1(K_BCM1480_INT_CYCLE_CP3)
+#define M_BCM1480_INT_TIMER_0		    _BCM1480_INT_MASK1(K_BCM1480_INT_TIMER_0)
+#define M_BCM1480_INT_TIMER_1		    _BCM1480_INT_MASK1(K_BCM1480_INT_TIMER_1)
+#define M_BCM1480_INT_TIMER_2		    _BCM1480_INT_MASK1(K_BCM1480_INT_TIMER_2)
+#define M_BCM1480_INT_TIMER_3		    _BCM1480_INT_MASK1(K_BCM1480_INT_TIMER_3)
+#define M_BCM1480_INT_DM_CH_0		    _BCM1480_INT_MASK1(K_BCM1480_INT_DM_CH_0)
+#define M_BCM1480_INT_DM_CH_1		    _BCM1480_INT_MASK1(K_BCM1480_INT_DM_CH_1)
+#define M_BCM1480_INT_DM_CH_2		    _BCM1480_INT_MASK1(K_BCM1480_INT_DM_CH_2)
+#define M_BCM1480_INT_DM_CH_3		    _BCM1480_INT_MASK1(K_BCM1480_INT_DM_CH_3)
+#define M_BCM1480_INT_MAC_0		    _BCM1480_INT_MASK1(K_BCM1480_INT_MAC_0)
+#define M_BCM1480_INT_MAC_0_CH1		    _BCM1480_INT_MASK1(K_BCM1480_INT_MAC_0_CH1)
+#define M_BCM1480_INT_MAC_1		    _BCM1480_INT_MASK1(K_BCM1480_INT_MAC_1)
+#define M_BCM1480_INT_MAC_1_CH1		    _BCM1480_INT_MASK1(K_BCM1480_INT_MAC_1_CH1)
+#define M_BCM1480_INT_MAC_2		    _BCM1480_INT_MASK1(K_BCM1480_INT_MAC_2)
+#define M_BCM1480_INT_MAC_2_CH1		    _BCM1480_INT_MASK1(K_BCM1480_INT_MAC_2_CH1)
+#define M_BCM1480_INT_MAC_3		    _BCM1480_INT_MASK1(K_BCM1480_INT_MAC_3)
+#define M_BCM1480_INT_MAC_3_CH1		    _BCM1480_INT_MASK1(K_BCM1480_INT_MAC_3_CH1)
+#define M_BCM1480_INT_PMI_LOW		    _BCM1480_INT_MASK1(K_BCM1480_INT_PMI_LOW)
+#define M_BCM1480_INT_PMI_HIGH		    _BCM1480_INT_MASK1(K_BCM1480_INT_PMI_HIGH)
+#define M_BCM1480_INT_PMO_LOW		    _BCM1480_INT_MASK1(K_BCM1480_INT_PMO_LOW)
+#define M_BCM1480_INT_PMO_HIGH		    _BCM1480_INT_MASK1(K_BCM1480_INT_PMO_HIGH)
+#define M_BCM1480_INT_MBOX_ALL		    _BCM1480_INT_MASK(8, K_BCM1480_INT_MBOX_0_0)
+#define M_BCM1480_INT_MBOX_0_0		    _BCM1480_INT_MASK1(K_BCM1480_INT_MBOX_0_0)
+#define M_BCM1480_INT_MBOX_0_1		    _BCM1480_INT_MASK1(K_BCM1480_INT_MBOX_0_1)
+#define M_BCM1480_INT_MBOX_0_2		    _BCM1480_INT_MASK1(K_BCM1480_INT_MBOX_0_2)
+#define M_BCM1480_INT_MBOX_0_3		    _BCM1480_INT_MASK1(K_BCM1480_INT_MBOX_0_3)
+#define M_BCM1480_INT_MBOX_1_0		    _BCM1480_INT_MASK1(K_BCM1480_INT_MBOX_1_0)
+#define M_BCM1480_INT_MBOX_1_1		    _BCM1480_INT_MASK1(K_BCM1480_INT_MBOX_1_1)
+#define M_BCM1480_INT_MBOX_1_2		    _BCM1480_INT_MASK1(K_BCM1480_INT_MBOX_1_2)
+#define M_BCM1480_INT_MBOX_1_3		    _BCM1480_INT_MASK1(K_BCM1480_INT_MBOX_1_3)
+#define M_BCM1480_INT_BAD_ECC		    _BCM1480_INT_MASK1(K_BCM1480_INT_BAD_ECC)
+#define M_BCM1480_INT_COR_ECC		    _BCM1480_INT_MASK1(K_BCM1480_INT_COR_ECC)
+#define M_BCM1480_INT_IO_BUS		    _BCM1480_INT_MASK1(K_BCM1480_INT_IO_BUS)
+#define M_BCM1480_INT_PERF_CNT		    _BCM1480_INT_MASK1(K_BCM1480_INT_PERF_CNT)
+#define M_BCM1480_INT_SW_PERF_CNT	    _BCM1480_INT_MASK1(K_BCM1480_INT_SW_PERF_CNT)
+#define M_BCM1480_INT_TRACE_FREEZE	    _BCM1480_INT_MASK1(K_BCM1480_INT_TRACE_FREEZE)
+#define M_BCM1480_INT_SW_TRACE_FREEZE	    _BCM1480_INT_MASK1(K_BCM1480_INT_SW_TRACE_FREEZE)
+#define M_BCM1480_INT_WATCHDOG_TIMER_0	    _BCM1480_INT_MASK1(K_BCM1480_INT_WATCHDOG_TIMER_0)
+#define M_BCM1480_INT_WATCHDOG_TIMER_1	    _BCM1480_INT_MASK1(K_BCM1480_INT_WATCHDOG_TIMER_1)
+#define M_BCM1480_INT_WATCHDOG_TIMER_2	    _BCM1480_INT_MASK1(K_BCM1480_INT_WATCHDOG_TIMER_2)
+#define M_BCM1480_INT_WATCHDOG_TIMER_3	    _BCM1480_INT_MASK1(K_BCM1480_INT_WATCHDOG_TIMER_3)
+#define M_BCM1480_INT_PCI_ERROR		    _BCM1480_INT_MASK1(K_BCM1480_INT_PCI_ERROR)
+#define M_BCM1480_INT_PCI_RESET		    _BCM1480_INT_MASK1(K_BCM1480_INT_PCI_RESET)
+#define M_BCM1480_INT_NODE_CONTROLLER	    _BCM1480_INT_MASK1(K_BCM1480_INT_NODE_CONTROLLER)
+#define M_BCM1480_INT_HOST_BRIDGE	    _BCM1480_INT_MASK1(K_BCM1480_INT_HOST_BRIDGE)
+#define M_BCM1480_INT_PORT_0_FATAL	    _BCM1480_INT_MASK1(K_BCM1480_INT_PORT_0_FATAL)
+#define M_BCM1480_INT_PORT_0_NONFATAL	    _BCM1480_INT_MASK1(K_BCM1480_INT_PORT_0_NONFATAL)
+#define M_BCM1480_INT_PORT_1_FATAL	    _BCM1480_INT_MASK1(K_BCM1480_INT_PORT_1_FATAL)
+#define M_BCM1480_INT_PORT_1_NONFATAL	    _BCM1480_INT_MASK1(K_BCM1480_INT_PORT_1_NONFATAL)
+#define M_BCM1480_INT_PORT_2_FATAL	    _BCM1480_INT_MASK1(K_BCM1480_INT_PORT_2_FATAL)
+#define M_BCM1480_INT_PORT_2_NONFATAL	    _BCM1480_INT_MASK1(K_BCM1480_INT_PORT_2_NONFATAL)
+#define M_BCM1480_INT_LDT_SMI		    _BCM1480_INT_MASK1(K_BCM1480_INT_LDT_SMI)
+#define M_BCM1480_INT_LDT_NMI		    _BCM1480_INT_MASK1(K_BCM1480_INT_LDT_NMI)
+#define M_BCM1480_INT_LDT_INIT		    _BCM1480_INT_MASK1(K_BCM1480_INT_LDT_INIT)
+#define M_BCM1480_INT_LDT_STARTUP	    _BCM1480_INT_MASK1(K_BCM1480_INT_LDT_STARTUP)
+#define M_BCM1480_INT_LDT_EXT		    _BCM1480_INT_MASK1(K_BCM1480_INT_LDT_EXT)
+#define M_BCM1480_INT_SMB_0		    _BCM1480_INT_MASK1(K_BCM1480_INT_SMB_0)
+#define M_BCM1480_INT_SMB_1		    _BCM1480_INT_MASK1(K_BCM1480_INT_SMB_1)
+#define M_BCM1480_INT_PCMCIA		    _BCM1480_INT_MASK1(K_BCM1480_INT_PCMCIA)
+#define M_BCM1480_INT_UART_0		    _BCM1480_INT_MASK1(K_BCM1480_INT_UART_0)
+#define M_BCM1480_INT_UART_1		    _BCM1480_INT_MASK1(K_BCM1480_INT_UART_1)
+#define M_BCM1480_INT_UART_2		    _BCM1480_INT_MASK1(K_BCM1480_INT_UART_2)
+#define M_BCM1480_INT_UART_3		    _BCM1480_INT_MASK1(K_BCM1480_INT_UART_3)
+#define M_BCM1480_INT_GPIO_4		    _BCM1480_INT_MASK1(K_BCM1480_INT_GPIO_4)
+#define M_BCM1480_INT_GPIO_5		    _BCM1480_INT_MASK1(K_BCM1480_INT_GPIO_5)
+#define M_BCM1480_INT_GPIO_6		    _BCM1480_INT_MASK1(K_BCM1480_INT_GPIO_6)
+#define M_BCM1480_INT_GPIO_7		    _BCM1480_INT_MASK1(K_BCM1480_INT_GPIO_7)
+#define M_BCM1480_INT_GPIO_8		    _BCM1480_INT_MASK1(K_BCM1480_INT_GPIO_8)
+#define M_BCM1480_INT_GPIO_9		    _BCM1480_INT_MASK1(K_BCM1480_INT_GPIO_9)
+#define M_BCM1480_INT_GPIO_10		    _BCM1480_INT_MASK1(K_BCM1480_INT_GPIO_10)
+#define M_BCM1480_INT_GPIO_11		    _BCM1480_INT_MASK1(K_BCM1480_INT_GPIO_11)
+#define M_BCM1480_INT_GPIO_12		    _BCM1480_INT_MASK1(K_BCM1480_INT_GPIO_12)
+#define M_BCM1480_INT_GPIO_13		    _BCM1480_INT_MASK1(K_BCM1480_INT_GPIO_13)
+#define M_BCM1480_INT_GPIO_14		    _BCM1480_INT_MASK1(K_BCM1480_INT_GPIO_14)
+#define M_BCM1480_INT_GPIO_15		    _BCM1480_INT_MASK1(K_BCM1480_INT_GPIO_15)
+
+/*
+ * Interrupt mappings (Table 18)
+ */
+
+#define K_BCM1480_INT_MAP_I0	0		/* interrupt pins on processor */
+#define K_BCM1480_INT_MAP_I1	1
+#define K_BCM1480_INT_MAP_I2	2
+#define K_BCM1480_INT_MAP_I3	3
+#define K_BCM1480_INT_MAP_I4	4
+#define K_BCM1480_INT_MAP_I5	5
+#define K_BCM1480_INT_MAP_NMI	6		/* nonmaskable */
+#define K_BCM1480_INT_MAP_DINT	7		/* debug interrupt */
+
+/*
+ * Interrupt LDT Set Register (Table 19)
+ */
+
+#define S_BCM1480_INT_HT_INTMSG		    0
+#define M_BCM1480_INT_HT_INTMSG		    _SB_MAKEMASK(3, S_BCM1480_INT_HT_INTMSG)
+#define V_BCM1480_INT_HT_INTMSG(x)	    _SB_MAKEVALUE(x, S_BCM1480_INT_HT_INTMSG)
+#define G_BCM1480_INT_HT_INTMSG(x)	    _SB_GETVALUE(x, S_BCM1480_INT_HT_INTMSG, M_BCM1480_INT_HT_INTMSG)
+
+#define K_BCM1480_INT_HT_INTMSG_FIXED	    0
+#define K_BCM1480_INT_HT_INTMSG_ARBITRATED  1
+#define K_BCM1480_INT_HT_INTMSG_SMI	    2
+#define K_BCM1480_INT_HT_INTMSG_NMI	    3
+#define K_BCM1480_INT_HT_INTMSG_INIT	    4
+#define K_BCM1480_INT_HT_INTMSG_STARTUP	    5
+#define K_BCM1480_INT_HT_INTMSG_EXTINT	    6
+#define K_BCM1480_INT_HT_INTMSG_RESERVED    7
+
+#define M_BCM1480_INT_HT_TRIGGERMODE	    _SB_MAKEMASK1(3)
+#define V_BCM1480_INT_HT_EDGETRIGGER	    0
+#define V_BCM1480_INT_HT_LEVELTRIGGER	    M_BCM1480_INT_HT_TRIGGERMODE
+
+#define M_BCM1480_INT_HT_DESTMODE	    _SB_MAKEMASK1(4)
+#define V_BCM1480_INT_HT_PHYSICALDEST	    0
+#define V_BCM1480_INT_HT_LOGICALDEST	    M_BCM1480_INT_HT_DESTMODE
+
+#define S_BCM1480_INT_HT_INTDEST	    5
+#define M_BCM1480_INT_HT_INTDEST	    _SB_MAKEMASK(8, S_BCM1480_INT_HT_INTDEST)
+#define V_BCM1480_INT_HT_INTDEST(x)	    _SB_MAKEVALUE(x, S_BCM1480_INT_HT_INTDEST)
+#define G_BCM1480_INT_HT_INTDEST(x)	    _SB_GETVALUE(x, S_BCM1480_INT_HT_INTDEST, M_BCM1480_INT_HT_INTDEST)
+
+#define S_BCM1480_INT_HT_VECTOR		    13
+#define M_BCM1480_INT_HT_VECTOR		    _SB_MAKEMASK(8, S_BCM1480_INT_HT_VECTOR)
+#define V_BCM1480_INT_HT_VECTOR(x)	    _SB_MAKEVALUE(x, S_BCM1480_INT_HT_VECTOR)
+#define G_BCM1480_INT_HT_VECTOR(x)	    _SB_GETVALUE(x, S_BCM1480_INT_HT_VECTOR, M_BCM1480_INT_HT_VECTOR)
+
+/*
+ * Vector prefix (Table 4-7)
+ */
+
+#define M_BCM1480_HTVECT_RAISE_INTLDT_HIGH  0x00
+#define M_BCM1480_HTVECT_RAISE_MBOX_0	    0x40
+#define M_BCM1480_HTVECT_RAISE_INTLDT_LO    0x80
+#define M_BCM1480_HTVECT_RAISE_MBOX_1	    0xC0
+
+#endif /* _BCM1480_INT_H */
diff --git a/arch/mips/include/asm/sibyte/bcm1480_l2c.h b/arch/mips/include/asm/sibyte/bcm1480_l2c.h
new file mode 100644
index 000000000..f6f3a1989
--- /dev/null
+++ b/arch/mips/include/asm/sibyte/bcm1480_l2c.h
@@ -0,0 +1,163 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*  *********************************************************************
+    *  BCM1280/BCM1480 Board Support Package
+    *
+    *  L2 Cache constants and macros		File: bcm1480_l2c.h
+    *
+    *  This module contains constants useful for manipulating the
+    *  level 2 cache.
+    *
+    *  BCM1400 specification level:  1280-UM100-D2 (11/14/03)
+    *
+    *********************************************************************
+    *
+    *  Copyright 2000,2001,2002,2003
+    *  Broadcom Corporation. All rights reserved.
+    *
+    ********************************************************************* */
+
+
+#ifndef _BCM1480_L2C_H
+#define _BCM1480_L2C_H
+
+#include <asm/sibyte/sb1250_defs.h>
+
+/*
+ * Format of level 2 cache management address (Table 55)
+ */
+
+#define S_BCM1480_L2C_MGMT_INDEX	    5
+#define M_BCM1480_L2C_MGMT_INDEX	    _SB_MAKEMASK(12, S_BCM1480_L2C_MGMT_INDEX)
+#define V_BCM1480_L2C_MGMT_INDEX(x)	    _SB_MAKEVALUE(x, S_BCM1480_L2C_MGMT_INDEX)
+#define G_BCM1480_L2C_MGMT_INDEX(x)	    _SB_GETVALUE(x, S_BCM1480_L2C_MGMT_INDEX, M_BCM1480_L2C_MGMT_INDEX)
+
+#define S_BCM1480_L2C_MGMT_WAY		    17
+#define M_BCM1480_L2C_MGMT_WAY		    _SB_MAKEMASK(3, S_BCM1480_L2C_MGMT_WAY)
+#define V_BCM1480_L2C_MGMT_WAY(x)	    _SB_MAKEVALUE(x, S_BCM1480_L2C_MGMT_WAY)
+#define G_BCM1480_L2C_MGMT_WAY(x)	    _SB_GETVALUE(x, S_BCM1480_L2C_MGMT_WAY, M_BCM1480_L2C_MGMT_WAY)
+
+#define M_BCM1480_L2C_MGMT_DIRTY	    _SB_MAKEMASK1(20)
+#define M_BCM1480_L2C_MGMT_VALID	    _SB_MAKEMASK1(21)
+
+#define S_BCM1480_L2C_MGMT_ECC_DIAG	    22
+#define M_BCM1480_L2C_MGMT_ECC_DIAG	    _SB_MAKEMASK(2, S_BCM1480_L2C_MGMT_ECC_DIAG)
+#define V_BCM1480_L2C_MGMT_ECC_DIAG(x)	    _SB_MAKEVALUE(x, S_BCM1480_L2C_MGMT_ECC_DIAG)
+#define G_BCM1480_L2C_MGMT_ECC_DIAG(x)	    _SB_GETVALUE(x, S_BCM1480_L2C_MGMT_ECC_DIAG, M_BCM1480_L2C_MGMT_ECC_DIAG)
+
+#define A_BCM1480_L2C_MGMT_TAG_BASE	    0x00D0000000
+
+#define BCM1480_L2C_ENTRIES_PER_WAY	    4096
+#define BCM1480_L2C_NUM_WAYS		    8
+
+
+/*
+ * Level 2 Cache Tag register (Table 59)
+ */
+
+#define S_BCM1480_L2C_TAG_MBZ		    0
+#define M_BCM1480_L2C_TAG_MBZ		    _SB_MAKEMASK(5, S_BCM1480_L2C_TAG_MBZ)
+
+#define S_BCM1480_L2C_TAG_INDEX		    5
+#define M_BCM1480_L2C_TAG_INDEX		    _SB_MAKEMASK(12, S_BCM1480_L2C_TAG_INDEX)
+#define V_BCM1480_L2C_TAG_INDEX(x)	    _SB_MAKEVALUE(x, S_BCM1480_L2C_TAG_INDEX)
+#define G_BCM1480_L2C_TAG_INDEX(x)	    _SB_GETVALUE(x, S_BCM1480_L2C_TAG_INDEX, M_BCM1480_L2C_TAG_INDEX)
+
+/* Note that index bit 16 is also tag bit 40 */
+#define S_BCM1480_L2C_TAG_TAG		    17
+#define M_BCM1480_L2C_TAG_TAG		    _SB_MAKEMASK(23, S_BCM1480_L2C_TAG_TAG)
+#define V_BCM1480_L2C_TAG_TAG(x)	    _SB_MAKEVALUE(x, S_BCM1480_L2C_TAG_TAG)
+#define G_BCM1480_L2C_TAG_TAG(x)	    _SB_GETVALUE(x, S_BCM1480_L2C_TAG_TAG, M_BCM1480_L2C_TAG_TAG)
+
+#define S_BCM1480_L2C_TAG_ECC		    40
+#define M_BCM1480_L2C_TAG_ECC		    _SB_MAKEMASK(6, S_BCM1480_L2C_TAG_ECC)
+#define V_BCM1480_L2C_TAG_ECC(x)	    _SB_MAKEVALUE(x, S_BCM1480_L2C_TAG_ECC)
+#define G_BCM1480_L2C_TAG_ECC(x)	    _SB_GETVALUE(x, S_BCM1480_L2C_TAG_ECC, M_BCM1480_L2C_TAG_ECC)
+
+#define S_BCM1480_L2C_TAG_WAY		    46
+#define M_BCM1480_L2C_TAG_WAY		    _SB_MAKEMASK(3, S_BCM1480_L2C_TAG_WAY)
+#define V_BCM1480_L2C_TAG_WAY(x)	    _SB_MAKEVALUE(x, S_BCM1480_L2C_TAG_WAY)
+#define G_BCM1480_L2C_TAG_WAY(x)	    _SB_GETVALUE(x, S_BCM1480_L2C_TAG_WAY, M_BCM1480_L2C_TAG_WAY)
+
+#define M_BCM1480_L2C_TAG_DIRTY		    _SB_MAKEMASK1(49)
+#define M_BCM1480_L2C_TAG_VALID		    _SB_MAKEMASK1(50)
+
+#define S_BCM1480_L2C_DATA_ECC		    51
+#define M_BCM1480_L2C_DATA_ECC		    _SB_MAKEMASK(10, S_BCM1480_L2C_DATA_ECC)
+#define V_BCM1480_L2C_DATA_ECC(x)	    _SB_MAKEVALUE(x, S_BCM1480_L2C_DATA_ECC)
+#define G_BCM1480_L2C_DATA_ECC(x)	    _SB_GETVALUE(x, S_BCM1480_L2C_DATA_ECC, M_BCM1480_L2C_DATA_ECC)
+
+
+/*
+ * L2 Misc0 Value Register (Table 60)
+ */
+
+#define S_BCM1480_L2C_MISC0_WAY_REMOTE	    0
+#define M_BCM1480_L2C_MISC0_WAY_REMOTE	    _SB_MAKEMASK(8, S_BCM1480_L2C_MISC0_WAY_REMOTE)
+#define G_BCM1480_L2C_MISC0_WAY_REMOTE(x)   _SB_GETVALUE(x, S_BCM1480_L2C_MISC0_WAY_REMOTE, M_BCM1480_L2C_MISC0_WAY_REMOTE)
+
+#define S_BCM1480_L2C_MISC0_WAY_LOCAL	    8
+#define M_BCM1480_L2C_MISC0_WAY_LOCAL	    _SB_MAKEMASK(8, S_BCM1480_L2C_MISC0_WAY_LOCAL)
+#define G_BCM1480_L2C_MISC0_WAY_LOCAL(x)    _SB_GETVALUE(x, S_BCM1480_L2C_MISC0_WAY_LOCAL, M_BCM1480_L2C_MISC0_WAY_LOCAL)
+
+#define S_BCM1480_L2C_MISC0_WAY_ENABLE	    16
+#define M_BCM1480_L2C_MISC0_WAY_ENABLE	    _SB_MAKEMASK(8, S_BCM1480_L2C_MISC0_WAY_ENABLE)
+#define G_BCM1480_L2C_MISC0_WAY_ENABLE(x)   _SB_GETVALUE(x, S_BCM1480_L2C_MISC0_WAY_ENABLE, M_BCM1480_L2C_MISC0_WAY_ENABLE)
+
+#define S_BCM1480_L2C_MISC0_CACHE_DISABLE   24
+#define M_BCM1480_L2C_MISC0_CACHE_DISABLE   _SB_MAKEMASK(2, S_BCM1480_L2C_MISC0_CACHE_DISABLE)
+#define G_BCM1480_L2C_MISC0_CACHE_DISABLE(x) _SB_GETVALUE(x, S_BCM1480_L2C_MISC0_CACHE_DISABLE, M_BCM1480_L2C_MISC0_CACHE_DISABLE)
+
+#define S_BCM1480_L2C_MISC0_CACHE_QUAD	    26
+#define M_BCM1480_L2C_MISC0_CACHE_QUAD	    _SB_MAKEMASK(2, S_BCM1480_L2C_MISC0_CACHE_QUAD)
+#define G_BCM1480_L2C_MISC0_CACHE_QUAD(x)   _SB_GETVALUE(x, S_BCM1480_L2C_MISC0_CACHE_QUAD, M_BCM1480_L2C_MISC0_CACHE_QUAD)
+
+#define S_BCM1480_L2C_MISC0_MC_PRIORITY	     30
+#define M_BCM1480_L2C_MISC0_MC_PRIORITY	     _SB_MAKEMASK1(S_BCM1480_L2C_MISC0_MC_PRIORITY)
+
+#define S_BCM1480_L2C_MISC0_ECC_CLEANUP	     31
+#define M_BCM1480_L2C_MISC0_ECC_CLEANUP	     _SB_MAKEMASK1(S_BCM1480_L2C_MISC0_ECC_CLEANUP)
+
+
+/*
+ * L2 Misc1 Value Register (Table 60)
+ */
+
+#define S_BCM1480_L2C_MISC1_WAY_AGENT_0	     0
+#define M_BCM1480_L2C_MISC1_WAY_AGENT_0	     _SB_MAKEMASK(8, S_BCM1480_L2C_MISC1_WAY_AGENT_0)
+#define G_BCM1480_L2C_MISC1_WAY_AGENT_0(x)   _SB_GETVALUE(x, S_BCM1480_L2C_MISC1_WAY_AGENT_0, M_BCM1480_L2C_MISC1_WAY_AGENT_0)
+
+#define S_BCM1480_L2C_MISC1_WAY_AGENT_1	     8
+#define M_BCM1480_L2C_MISC1_WAY_AGENT_1	     _SB_MAKEMASK(8, S_BCM1480_L2C_MISC1_WAY_AGENT_1)
+#define G_BCM1480_L2C_MISC1_WAY_AGENT_1(x)   _SB_GETVALUE(x, S_BCM1480_L2C_MISC1_WAY_AGENT_1, M_BCM1480_L2C_MISC1_WAY_AGENT_1)
+
+#define S_BCM1480_L2C_MISC1_WAY_AGENT_2	     16
+#define M_BCM1480_L2C_MISC1_WAY_AGENT_2	     _SB_MAKEMASK(8, S_BCM1480_L2C_MISC1_WAY_AGENT_2)
+#define G_BCM1480_L2C_MISC1_WAY_AGENT_2(x)   _SB_GETVALUE(x, S_BCM1480_L2C_MISC1_WAY_AGENT_2, M_BCM1480_L2C_MISC1_WAY_AGENT_2)
+
+#define S_BCM1480_L2C_MISC1_WAY_AGENT_3	     24
+#define M_BCM1480_L2C_MISC1_WAY_AGENT_3	     _SB_MAKEMASK(8, S_BCM1480_L2C_MISC1_WAY_AGENT_3)
+#define G_BCM1480_L2C_MISC1_WAY_AGENT_3(x)   _SB_GETVALUE(x, S_BCM1480_L2C_MISC1_WAY_AGENT_3, M_BCM1480_L2C_MISC1_WAY_AGENT_3)
+
+#define S_BCM1480_L2C_MISC1_WAY_AGENT_4	     32
+#define M_BCM1480_L2C_MISC1_WAY_AGENT_4	     _SB_MAKEMASK(8, S_BCM1480_L2C_MISC1_WAY_AGENT_4)
+#define G_BCM1480_L2C_MISC1_WAY_AGENT_4(x)   _SB_GETVALUE(x, S_BCM1480_L2C_MISC1_WAY_AGENT_4, M_BCM1480_L2C_MISC1_WAY_AGENT_4)
+
+
+/*
+ * L2 Misc2 Value Register (Table 60)
+ */
+
+#define S_BCM1480_L2C_MISC2_WAY_AGENT_8	     0
+#define M_BCM1480_L2C_MISC2_WAY_AGENT_8	     _SB_MAKEMASK(8, S_BCM1480_L2C_MISC2_WAY_AGENT_8)
+#define G_BCM1480_L2C_MISC2_WAY_AGENT_8(x)   _SB_GETVALUE(x, S_BCM1480_L2C_MISC2_WAY_AGENT_8, M_BCM1480_L2C_MISC2_WAY_AGENT_8)
+
+#define S_BCM1480_L2C_MISC2_WAY_AGENT_9	     8
+#define M_BCM1480_L2C_MISC2_WAY_AGENT_9	     _SB_MAKEMASK(8, S_BCM1480_L2C_MISC2_WAY_AGENT_9)
+#define G_BCM1480_L2C_MISC2_WAY_AGENT_9(x)   _SB_GETVALUE(x, S_BCM1480_L2C_MISC2_WAY_AGENT_9, M_BCM1480_L2C_MISC2_WAY_AGENT_9)
+
+#define S_BCM1480_L2C_MISC2_WAY_AGENT_A	     16
+#define M_BCM1480_L2C_MISC2_WAY_AGENT_A	     _SB_MAKEMASK(8, S_BCM1480_L2C_MISC2_WAY_AGENT_A)
+#define G_BCM1480_L2C_MISC2_WAY_AGENT_A(x)   _SB_GETVALUE(x, S_BCM1480_L2C_MISC2_WAY_AGENT_A, M_BCM1480_L2C_MISC2_WAY_AGENT_A)
+
+
+#endif /* _BCM1480_L2C_H */
diff --git a/arch/mips/include/asm/sibyte/bcm1480_mc.h b/arch/mips/include/asm/sibyte/bcm1480_mc.h
new file mode 100644
index 000000000..1d9b62d47
--- /dev/null
+++ b/arch/mips/include/asm/sibyte/bcm1480_mc.h
@@ -0,0 +1,971 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*  *********************************************************************
+    *  BCM1280/BCM1480 Board Support Package
+    *
+    *  Memory Controller constants		File: bcm1480_mc.h
+    *
+    *  This module contains constants and macros useful for
+    *  programming the memory controller.
+    *
+    *  BCM1400 specification level:  1280-UM100-D1 (11/14/03 Review Copy)
+    *
+    *********************************************************************
+    *
+    *  Copyright 2000,2001,2002,2003
+    *  Broadcom Corporation. All rights reserved.
+    *
+    ********************************************************************* */
+
+
+#ifndef _BCM1480_MC_H
+#define _BCM1480_MC_H
+
+#include <asm/sibyte/sb1250_defs.h>
+
+/*
+ * Memory Channel Configuration Register (Table 81)
+ */
+
+#define S_BCM1480_MC_INTLV0		    0
+#define M_BCM1480_MC_INTLV0		    _SB_MAKEMASK(6, S_BCM1480_MC_INTLV0)
+#define V_BCM1480_MC_INTLV0(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_INTLV0)
+#define G_BCM1480_MC_INTLV0(x)		    _SB_GETVALUE(x, S_BCM1480_MC_INTLV0, M_BCM1480_MC_INTLV0)
+#define V_BCM1480_MC_INTLV0_DEFAULT	    V_BCM1480_MC_INTLV0(0)
+
+#define S_BCM1480_MC_INTLV1		    8
+#define M_BCM1480_MC_INTLV1		    _SB_MAKEMASK(6, S_BCM1480_MC_INTLV1)
+#define V_BCM1480_MC_INTLV1(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_INTLV1)
+#define G_BCM1480_MC_INTLV1(x)		    _SB_GETVALUE(x, S_BCM1480_MC_INTLV1, M_BCM1480_MC_INTLV1)
+#define V_BCM1480_MC_INTLV1_DEFAULT	    V_BCM1480_MC_INTLV1(0)
+
+#define S_BCM1480_MC_INTLV2		    16
+#define M_BCM1480_MC_INTLV2		    _SB_MAKEMASK(6, S_BCM1480_MC_INTLV2)
+#define V_BCM1480_MC_INTLV2(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_INTLV2)
+#define G_BCM1480_MC_INTLV2(x)		    _SB_GETVALUE(x, S_BCM1480_MC_INTLV2, M_BCM1480_MC_INTLV2)
+#define V_BCM1480_MC_INTLV2_DEFAULT	    V_BCM1480_MC_INTLV2(0)
+
+#define S_BCM1480_MC_CS_MODE		    32
+#define M_BCM1480_MC_CS_MODE		    _SB_MAKEMASK(8, S_BCM1480_MC_CS_MODE)
+#define V_BCM1480_MC_CS_MODE(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_CS_MODE)
+#define G_BCM1480_MC_CS_MODE(x)		    _SB_GETVALUE(x, S_BCM1480_MC_CS_MODE, M_BCM1480_MC_CS_MODE)
+#define V_BCM1480_MC_CS_MODE_DEFAULT	    V_BCM1480_MC_CS_MODE(0)
+
+#define V_BCM1480_MC_CONFIG_DEFAULT	    (V_BCM1480_MC_INTLV0_DEFAULT  | \
+				     V_BCM1480_MC_INTLV1_DEFAULT  | \
+				     V_BCM1480_MC_INTLV2_DEFAULT  | \
+				     V_BCM1480_MC_CS_MODE_DEFAULT)
+
+#define K_BCM1480_MC_CS01_MODE		    0x03
+#define K_BCM1480_MC_CS02_MODE		    0x05
+#define K_BCM1480_MC_CS0123_MODE	    0x0F
+#define K_BCM1480_MC_CS0246_MODE	    0x55
+#define K_BCM1480_MC_CS0145_MODE	    0x33
+#define K_BCM1480_MC_CS0167_MODE	    0xC3
+#define K_BCM1480_MC_CSFULL_MODE	    0xFF
+
+/*
+ * Chip Select Start Address Register (Table 82)
+ */
+
+#define S_BCM1480_MC_CS0_START		    0
+#define M_BCM1480_MC_CS0_START		    _SB_MAKEMASK(12, S_BCM1480_MC_CS0_START)
+#define V_BCM1480_MC_CS0_START(x)	    _SB_MAKEVALUE(x, S_BCM1480_MC_CS0_START)
+#define G_BCM1480_MC_CS0_START(x)	    _SB_GETVALUE(x, S_BCM1480_MC_CS0_START, M_BCM1480_MC_CS0_START)
+
+#define S_BCM1480_MC_CS1_START		    16
+#define M_BCM1480_MC_CS1_START		    _SB_MAKEMASK(12, S_BCM1480_MC_CS1_START)
+#define V_BCM1480_MC_CS1_START(x)	    _SB_MAKEVALUE(x, S_BCM1480_MC_CS1_START)
+#define G_BCM1480_MC_CS1_START(x)	    _SB_GETVALUE(x, S_BCM1480_MC_CS1_START, M_BCM1480_MC_CS1_START)
+
+#define S_BCM1480_MC_CS2_START		    32
+#define M_BCM1480_MC_CS2_START		    _SB_MAKEMASK(12, S_BCM1480_MC_CS2_START)
+#define V_BCM1480_MC_CS2_START(x)	    _SB_MAKEVALUE(x, S_BCM1480_MC_CS2_START)
+#define G_BCM1480_MC_CS2_START(x)	    _SB_GETVALUE(x, S_BCM1480_MC_CS2_START, M_BCM1480_MC_CS2_START)
+
+#define S_BCM1480_MC_CS3_START		    48
+#define M_BCM1480_MC_CS3_START		    _SB_MAKEMASK(12, S_BCM1480_MC_CS3_START)
+#define V_BCM1480_MC_CS3_START(x)	    _SB_MAKEVALUE(x, S_BCM1480_MC_CS3_START)
+#define G_BCM1480_MC_CS3_START(x)	    _SB_GETVALUE(x, S_BCM1480_MC_CS3_START, M_BCM1480_MC_CS3_START)
+
+/*
+ * Chip Select End Address Register (Table 83)
+ */
+
+#define S_BCM1480_MC_CS0_END		    0
+#define M_BCM1480_MC_CS0_END		    _SB_MAKEMASK(12, S_BCM1480_MC_CS0_END)
+#define V_BCM1480_MC_CS0_END(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_CS0_END)
+#define G_BCM1480_MC_CS0_END(x)		    _SB_GETVALUE(x, S_BCM1480_MC_CS0_END, M_BCM1480_MC_CS0_END)
+
+#define S_BCM1480_MC_CS1_END		    16
+#define M_BCM1480_MC_CS1_END		    _SB_MAKEMASK(12, S_BCM1480_MC_CS1_END)
+#define V_BCM1480_MC_CS1_END(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_CS1_END)
+#define G_BCM1480_MC_CS1_END(x)		    _SB_GETVALUE(x, S_BCM1480_MC_CS1_END, M_BCM1480_MC_CS1_END)
+
+#define S_BCM1480_MC_CS2_END		    32
+#define M_BCM1480_MC_CS2_END		    _SB_MAKEMASK(12, S_BCM1480_MC_CS2_END)
+#define V_BCM1480_MC_CS2_END(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_CS2_END)
+#define G_BCM1480_MC_CS2_END(x)		    _SB_GETVALUE(x, S_BCM1480_MC_CS2_END, M_BCM1480_MC_CS2_END)
+
+#define S_BCM1480_MC_CS3_END		    48
+#define M_BCM1480_MC_CS3_END		    _SB_MAKEMASK(12, S_BCM1480_MC_CS3_END)
+#define V_BCM1480_MC_CS3_END(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_CS3_END)
+#define G_BCM1480_MC_CS3_END(x)		    _SB_GETVALUE(x, S_BCM1480_MC_CS3_END, M_BCM1480_MC_CS3_END)
+
+/*
+ * Row Address Bit Select Register 0 (Table 84)
+ */
+
+#define S_BCM1480_MC_ROW00		    0
+#define M_BCM1480_MC_ROW00		    _SB_MAKEMASK(6, S_BCM1480_MC_ROW00)
+#define V_BCM1480_MC_ROW00(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_ROW00)
+#define G_BCM1480_MC_ROW00(x)		    _SB_GETVALUE(x, S_BCM1480_MC_ROW00, M_BCM1480_MC_ROW00)
+
+#define S_BCM1480_MC_ROW01		    8
+#define M_BCM1480_MC_ROW01		    _SB_MAKEMASK(6, S_BCM1480_MC_ROW01)
+#define V_BCM1480_MC_ROW01(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_ROW01)
+#define G_BCM1480_MC_ROW01(x)		    _SB_GETVALUE(x, S_BCM1480_MC_ROW01, M_BCM1480_MC_ROW01)
+
+#define S_BCM1480_MC_ROW02		    16
+#define M_BCM1480_MC_ROW02		    _SB_MAKEMASK(6, S_BCM1480_MC_ROW02)
+#define V_BCM1480_MC_ROW02(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_ROW02)
+#define G_BCM1480_MC_ROW02(x)		    _SB_GETVALUE(x, S_BCM1480_MC_ROW02, M_BCM1480_MC_ROW02)
+
+#define S_BCM1480_MC_ROW03		    24
+#define M_BCM1480_MC_ROW03		    _SB_MAKEMASK(6, S_BCM1480_MC_ROW03)
+#define V_BCM1480_MC_ROW03(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_ROW03)
+#define G_BCM1480_MC_ROW03(x)		    _SB_GETVALUE(x, S_BCM1480_MC_ROW03, M_BCM1480_MC_ROW03)
+
+#define S_BCM1480_MC_ROW04		    32
+#define M_BCM1480_MC_ROW04		    _SB_MAKEMASK(6, S_BCM1480_MC_ROW04)
+#define V_BCM1480_MC_ROW04(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_ROW04)
+#define G_BCM1480_MC_ROW04(x)		    _SB_GETVALUE(x, S_BCM1480_MC_ROW04, M_BCM1480_MC_ROW04)
+
+#define S_BCM1480_MC_ROW05		    40
+#define M_BCM1480_MC_ROW05		    _SB_MAKEMASK(6, S_BCM1480_MC_ROW05)
+#define V_BCM1480_MC_ROW05(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_ROW05)
+#define G_BCM1480_MC_ROW05(x)		    _SB_GETVALUE(x, S_BCM1480_MC_ROW05, M_BCM1480_MC_ROW05)
+
+#define S_BCM1480_MC_ROW06		    48
+#define M_BCM1480_MC_ROW06		    _SB_MAKEMASK(6, S_BCM1480_MC_ROW06)
+#define V_BCM1480_MC_ROW06(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_ROW06)
+#define G_BCM1480_MC_ROW06(x)		    _SB_GETVALUE(x, S_BCM1480_MC_ROW06, M_BCM1480_MC_ROW06)
+
+#define S_BCM1480_MC_ROW07		    56
+#define M_BCM1480_MC_ROW07		    _SB_MAKEMASK(6, S_BCM1480_MC_ROW07)
+#define V_BCM1480_MC_ROW07(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_ROW07)
+#define G_BCM1480_MC_ROW07(x)		    _SB_GETVALUE(x, S_BCM1480_MC_ROW07, M_BCM1480_MC_ROW07)
+
+/*
+ * Row Address Bit Select Register 1 (Table 85)
+ */
+
+#define S_BCM1480_MC_ROW08		    0
+#define M_BCM1480_MC_ROW08		    _SB_MAKEMASK(6, S_BCM1480_MC_ROW08)
+#define V_BCM1480_MC_ROW08(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_ROW08)
+#define G_BCM1480_MC_ROW08(x)		    _SB_GETVALUE(x, S_BCM1480_MC_ROW08, M_BCM1480_MC_ROW08)
+
+#define S_BCM1480_MC_ROW09		    8
+#define M_BCM1480_MC_ROW09		    _SB_MAKEMASK(6, S_BCM1480_MC_ROW09)
+#define V_BCM1480_MC_ROW09(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_ROW09)
+#define G_BCM1480_MC_ROW09(x)		    _SB_GETVALUE(x, S_BCM1480_MC_ROW09, M_BCM1480_MC_ROW09)
+
+#define S_BCM1480_MC_ROW10		    16
+#define M_BCM1480_MC_ROW10		    _SB_MAKEMASK(6, S_BCM1480_MC_ROW10)
+#define V_BCM1480_MC_ROW10(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_ROW10)
+#define G_BCM1480_MC_ROW10(x)		    _SB_GETVALUE(x, S_BCM1480_MC_ROW10, M_BCM1480_MC_ROW10)
+
+#define S_BCM1480_MC_ROW11		    24
+#define M_BCM1480_MC_ROW11		    _SB_MAKEMASK(6, S_BCM1480_MC_ROW11)
+#define V_BCM1480_MC_ROW11(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_ROW11)
+#define G_BCM1480_MC_ROW11(x)		    _SB_GETVALUE(x, S_BCM1480_MC_ROW11, M_BCM1480_MC_ROW11)
+
+#define S_BCM1480_MC_ROW12		    32
+#define M_BCM1480_MC_ROW12		    _SB_MAKEMASK(6, S_BCM1480_MC_ROW12)
+#define V_BCM1480_MC_ROW12(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_ROW12)
+#define G_BCM1480_MC_ROW12(x)		    _SB_GETVALUE(x, S_BCM1480_MC_ROW12, M_BCM1480_MC_ROW12)
+
+#define S_BCM1480_MC_ROW13		    40
+#define M_BCM1480_MC_ROW13		    _SB_MAKEMASK(6, S_BCM1480_MC_ROW13)
+#define V_BCM1480_MC_ROW13(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_ROW13)
+#define G_BCM1480_MC_ROW13(x)		    _SB_GETVALUE(x, S_BCM1480_MC_ROW13, M_BCM1480_MC_ROW13)
+
+#define S_BCM1480_MC_ROW14		    48
+#define M_BCM1480_MC_ROW14		    _SB_MAKEMASK(6, S_BCM1480_MC_ROW14)
+#define V_BCM1480_MC_ROW14(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_ROW14)
+#define G_BCM1480_MC_ROW14(x)		    _SB_GETVALUE(x, S_BCM1480_MC_ROW14, M_BCM1480_MC_ROW14)
+
+#define K_BCM1480_MC_ROWX_BIT_SPACING	    8
+
+/*
+ * Column Address Bit Select Register 0 (Table 86)
+ */
+
+#define S_BCM1480_MC_COL00		    0
+#define M_BCM1480_MC_COL00		    _SB_MAKEMASK(6, S_BCM1480_MC_COL00)
+#define V_BCM1480_MC_COL00(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_COL00)
+#define G_BCM1480_MC_COL00(x)		    _SB_GETVALUE(x, S_BCM1480_MC_COL00, M_BCM1480_MC_COL00)
+
+#define S_BCM1480_MC_COL01		    8
+#define M_BCM1480_MC_COL01		    _SB_MAKEMASK(6, S_BCM1480_MC_COL01)
+#define V_BCM1480_MC_COL01(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_COL01)
+#define G_BCM1480_MC_COL01(x)		    _SB_GETVALUE(x, S_BCM1480_MC_COL01, M_BCM1480_MC_COL01)
+
+#define S_BCM1480_MC_COL02		    16
+#define M_BCM1480_MC_COL02		    _SB_MAKEMASK(6, S_BCM1480_MC_COL02)
+#define V_BCM1480_MC_COL02(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_COL02)
+#define G_BCM1480_MC_COL02(x)		    _SB_GETVALUE(x, S_BCM1480_MC_COL02, M_BCM1480_MC_COL02)
+
+#define S_BCM1480_MC_COL03		    24
+#define M_BCM1480_MC_COL03		    _SB_MAKEMASK(6, S_BCM1480_MC_COL03)
+#define V_BCM1480_MC_COL03(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_COL03)
+#define G_BCM1480_MC_COL03(x)		    _SB_GETVALUE(x, S_BCM1480_MC_COL03, M_BCM1480_MC_COL03)
+
+#define S_BCM1480_MC_COL04		    32
+#define M_BCM1480_MC_COL04		    _SB_MAKEMASK(6, S_BCM1480_MC_COL04)
+#define V_BCM1480_MC_COL04(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_COL04)
+#define G_BCM1480_MC_COL04(x)		    _SB_GETVALUE(x, S_BCM1480_MC_COL04, M_BCM1480_MC_COL04)
+
+#define S_BCM1480_MC_COL05		    40
+#define M_BCM1480_MC_COL05		    _SB_MAKEMASK(6, S_BCM1480_MC_COL05)
+#define V_BCM1480_MC_COL05(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_COL05)
+#define G_BCM1480_MC_COL05(x)		    _SB_GETVALUE(x, S_BCM1480_MC_COL05, M_BCM1480_MC_COL05)
+
+#define S_BCM1480_MC_COL06		    48
+#define M_BCM1480_MC_COL06		    _SB_MAKEMASK(6, S_BCM1480_MC_COL06)
+#define V_BCM1480_MC_COL06(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_COL06)
+#define G_BCM1480_MC_COL06(x)		    _SB_GETVALUE(x, S_BCM1480_MC_COL06, M_BCM1480_MC_COL06)
+
+#define S_BCM1480_MC_COL07		    56
+#define M_BCM1480_MC_COL07		    _SB_MAKEMASK(6, S_BCM1480_MC_COL07)
+#define V_BCM1480_MC_COL07(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_COL07)
+#define G_BCM1480_MC_COL07(x)		    _SB_GETVALUE(x, S_BCM1480_MC_COL07, M_BCM1480_MC_COL07)
+
+/*
+ * Column Address Bit Select Register 1 (Table 87)
+ */
+
+#define S_BCM1480_MC_COL08		    0
+#define M_BCM1480_MC_COL08		    _SB_MAKEMASK(6, S_BCM1480_MC_COL08)
+#define V_BCM1480_MC_COL08(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_COL08)
+#define G_BCM1480_MC_COL08(x)		    _SB_GETVALUE(x, S_BCM1480_MC_COL08, M_BCM1480_MC_COL08)
+
+#define S_BCM1480_MC_COL09		    8
+#define M_BCM1480_MC_COL09		    _SB_MAKEMASK(6, S_BCM1480_MC_COL09)
+#define V_BCM1480_MC_COL09(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_COL09)
+#define G_BCM1480_MC_COL09(x)		    _SB_GETVALUE(x, S_BCM1480_MC_COL09, M_BCM1480_MC_COL09)
+
+#define S_BCM1480_MC_COL10		    16	 /* not a valid position, must be prog as 0 */
+
+#define S_BCM1480_MC_COL11		    24
+#define M_BCM1480_MC_COL11		    _SB_MAKEMASK(6, S_BCM1480_MC_COL11)
+#define V_BCM1480_MC_COL11(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_COL11)
+#define G_BCM1480_MC_COL11(x)		    _SB_GETVALUE(x, S_BCM1480_MC_COL11, M_BCM1480_MC_COL11)
+
+#define S_BCM1480_MC_COL12		    32
+#define M_BCM1480_MC_COL12		    _SB_MAKEMASK(6, S_BCM1480_MC_COL12)
+#define V_BCM1480_MC_COL12(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_COL12)
+#define G_BCM1480_MC_COL12(x)		    _SB_GETVALUE(x, S_BCM1480_MC_COL12, M_BCM1480_MC_COL12)
+
+#define S_BCM1480_MC_COL13		    40
+#define M_BCM1480_MC_COL13		    _SB_MAKEMASK(6, S_BCM1480_MC_COL13)
+#define V_BCM1480_MC_COL13(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_COL13)
+#define G_BCM1480_MC_COL13(x)		    _SB_GETVALUE(x, S_BCM1480_MC_COL13, M_BCM1480_MC_COL13)
+
+#define S_BCM1480_MC_COL14		    48
+#define M_BCM1480_MC_COL14		    _SB_MAKEMASK(6, S_BCM1480_MC_COL14)
+#define V_BCM1480_MC_COL14(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_COL14)
+#define G_BCM1480_MC_COL14(x)		    _SB_GETVALUE(x, S_BCM1480_MC_COL14, M_BCM1480_MC_COL14)
+
+#define K_BCM1480_MC_COLX_BIT_SPACING	    8
+
+/*
+ * CS0 and CS1 Bank Address Bit Select Register (Table 88)
+ */
+
+#define S_BCM1480_MC_CS01_BANK0		    0
+#define M_BCM1480_MC_CS01_BANK0		    _SB_MAKEMASK(6, S_BCM1480_MC_CS01_BANK0)
+#define V_BCM1480_MC_CS01_BANK0(x)	    _SB_MAKEVALUE(x, S_BCM1480_MC_CS01_BANK0)
+#define G_BCM1480_MC_CS01_BANK0(x)	    _SB_GETVALUE(x, S_BCM1480_MC_CS01_BANK0, M_BCM1480_MC_CS01_BANK0)
+
+#define S_BCM1480_MC_CS01_BANK1		    8
+#define M_BCM1480_MC_CS01_BANK1		    _SB_MAKEMASK(6, S_BCM1480_MC_CS01_BANK1)
+#define V_BCM1480_MC_CS01_BANK1(x)	    _SB_MAKEVALUE(x, S_BCM1480_MC_CS01_BANK1)
+#define G_BCM1480_MC_CS01_BANK1(x)	    _SB_GETVALUE(x, S_BCM1480_MC_CS01_BANK1, M_BCM1480_MC_CS01_BANK1)
+
+#define S_BCM1480_MC_CS01_BANK2		    16
+#define M_BCM1480_MC_CS01_BANK2		    _SB_MAKEMASK(6, S_BCM1480_MC_CS01_BANK2)
+#define V_BCM1480_MC_CS01_BANK2(x)	    _SB_MAKEVALUE(x, S_BCM1480_MC_CS01_BANK2)
+#define G_BCM1480_MC_CS01_BANK2(x)	    _SB_GETVALUE(x, S_BCM1480_MC_CS01_BANK2, M_BCM1480_MC_CS01_BANK2)
+
+/*
+ * CS2 and CS3 Bank Address Bit Select Register (Table 89)
+ */
+
+#define S_BCM1480_MC_CS23_BANK0		    0
+#define M_BCM1480_MC_CS23_BANK0		    _SB_MAKEMASK(6, S_BCM1480_MC_CS23_BANK0)
+#define V_BCM1480_MC_CS23_BANK0(x)	    _SB_MAKEVALUE(x, S_BCM1480_MC_CS23_BANK0)
+#define G_BCM1480_MC_CS23_BANK0(x)	    _SB_GETVALUE(x, S_BCM1480_MC_CS23_BANK0, M_BCM1480_MC_CS23_BANK0)
+
+#define S_BCM1480_MC_CS23_BANK1		    8
+#define M_BCM1480_MC_CS23_BANK1		    _SB_MAKEMASK(6, S_BCM1480_MC_CS23_BANK1)
+#define V_BCM1480_MC_CS23_BANK1(x)	    _SB_MAKEVALUE(x, S_BCM1480_MC_CS23_BANK1)
+#define G_BCM1480_MC_CS23_BANK1(x)	    _SB_GETVALUE(x, S_BCM1480_MC_CS23_BANK1, M_BCM1480_MC_CS23_BANK1)
+
+#define S_BCM1480_MC_CS23_BANK2		    16
+#define M_BCM1480_MC_CS23_BANK2		    _SB_MAKEMASK(6, S_BCM1480_MC_CS23_BANK2)
+#define V_BCM1480_MC_CS23_BANK2(x)	    _SB_MAKEVALUE(x, S_BCM1480_MC_CS23_BANK2)
+#define G_BCM1480_MC_CS23_BANK2(x)	    _SB_GETVALUE(x, S_BCM1480_MC_CS23_BANK2, M_BCM1480_MC_CS23_BANK2)
+
+#define K_BCM1480_MC_CSXX_BANKX_BIT_SPACING  8
+
+/*
+ * DRAM Command Register (Table 90)
+ */
+
+#define S_BCM1480_MC_COMMAND		    0
+#define M_BCM1480_MC_COMMAND		    _SB_MAKEMASK(4, S_BCM1480_MC_COMMAND)
+#define V_BCM1480_MC_COMMAND(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_COMMAND)
+#define G_BCM1480_MC_COMMAND(x)		    _SB_GETVALUE(x, S_BCM1480_MC_COMMAND, M_BCM1480_MC_COMMAND)
+
+#define K_BCM1480_MC_COMMAND_EMRS	    0
+#define K_BCM1480_MC_COMMAND_MRS	    1
+#define K_BCM1480_MC_COMMAND_PRE	    2
+#define K_BCM1480_MC_COMMAND_AR		    3
+#define K_BCM1480_MC_COMMAND_SETRFSH	    4
+#define K_BCM1480_MC_COMMAND_CLRRFSH	    5
+#define K_BCM1480_MC_COMMAND_SETPWRDN	    6
+#define K_BCM1480_MC_COMMAND_CLRPWRDN	    7
+
+#if SIBYTE_HDR_FEATURE(1480, PASS2)
+#define K_BCM1480_MC_COMMAND_EMRS2	    8
+#define K_BCM1480_MC_COMMAND_EMRS3	    9
+#define K_BCM1480_MC_COMMAND_ENABLE_MCLK    10
+#define K_BCM1480_MC_COMMAND_DISABLE_MCLK   11
+#endif
+
+#define V_BCM1480_MC_COMMAND_EMRS	    V_BCM1480_MC_COMMAND(K_BCM1480_MC_COMMAND_EMRS)
+#define V_BCM1480_MC_COMMAND_MRS	    V_BCM1480_MC_COMMAND(K_BCM1480_MC_COMMAND_MRS)
+#define V_BCM1480_MC_COMMAND_PRE	    V_BCM1480_MC_COMMAND(K_BCM1480_MC_COMMAND_PRE)
+#define V_BCM1480_MC_COMMAND_AR		    V_BCM1480_MC_COMMAND(K_BCM1480_MC_COMMAND_AR)
+#define V_BCM1480_MC_COMMAND_SETRFSH	    V_BCM1480_MC_COMMAND(K_BCM1480_MC_COMMAND_SETRFSH)
+#define V_BCM1480_MC_COMMAND_CLRRFSH	    V_BCM1480_MC_COMMAND(K_BCM1480_MC_COMMAND_CLRRFSH)
+#define V_BCM1480_MC_COMMAND_SETPWRDN	    V_BCM1480_MC_COMMAND(K_BCM1480_MC_COMMAND_SETPWRDN)
+#define V_BCM1480_MC_COMMAND_CLRPWRDN	    V_BCM1480_MC_COMMAND(K_BCM1480_MC_COMMAND_CLRPWRDN)
+
+#if SIBYTE_HDR_FEATURE(1480, PASS2)
+#define V_BCM1480_MC_COMMAND_EMRS2	    V_BCM1480_MC_COMMAND(K_BCM1480_MC_COMMAND_EMRS2)
+#define V_BCM1480_MC_COMMAND_EMRS3	    V_BCM1480_MC_COMMAND(K_BCM1480_MC_COMMAND_EMRS3)
+#define V_BCM1480_MC_COMMAND_ENABLE_MCLK    V_BCM1480_MC_COMMAND(K_BCM1480_MC_COMMAND_ENABLE_MCLK)
+#define V_BCM1480_MC_COMMAND_DISABLE_MCLK   V_BCM1480_MC_COMMAND(K_BCM1480_MC_COMMAND_DISABLE_MCLK)
+#endif
+
+#define S_BCM1480_MC_CS0		    4
+#define M_BCM1480_MC_CS0		    _SB_MAKEMASK1(4)
+#define M_BCM1480_MC_CS1		    _SB_MAKEMASK1(5)
+#define M_BCM1480_MC_CS2		    _SB_MAKEMASK1(6)
+#define M_BCM1480_MC_CS3		    _SB_MAKEMASK1(7)
+#define M_BCM1480_MC_CS4		    _SB_MAKEMASK1(8)
+#define M_BCM1480_MC_CS5		    _SB_MAKEMASK1(9)
+#define M_BCM1480_MC_CS6		    _SB_MAKEMASK1(10)
+#define M_BCM1480_MC_CS7		    _SB_MAKEMASK1(11)
+
+#define M_BCM1480_MC_CS			 _SB_MAKEMASK(8, S_BCM1480_MC_CS0)
+#define V_BCM1480_MC_CS(x)		 _SB_MAKEVALUE(x, S_BCM1480_MC_CS0)
+#define G_BCM1480_MC_CS(x)		 _SB_GETVALUE(x, S_BCM1480_MC_CS0, M_BCM1480_MC_CS0)
+
+#define M_BCM1480_MC_CMD_ACTIVE		    _SB_MAKEMASK1(16)
+
+/*
+ * DRAM Mode Register (Table 91)
+ */
+
+#define S_BCM1480_MC_EMODE		    0
+#define M_BCM1480_MC_EMODE		    _SB_MAKEMASK(15, S_BCM1480_MC_EMODE)
+#define V_BCM1480_MC_EMODE(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_EMODE)
+#define G_BCM1480_MC_EMODE(x)		    _SB_GETVALUE(x, S_BCM1480_MC_EMODE, M_BCM1480_MC_EMODE)
+#define V_BCM1480_MC_EMODE_DEFAULT	    V_BCM1480_MC_EMODE(0)
+
+#define S_BCM1480_MC_MODE		    16
+#define M_BCM1480_MC_MODE		    _SB_MAKEMASK(15, S_BCM1480_MC_MODE)
+#define V_BCM1480_MC_MODE(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_MODE)
+#define G_BCM1480_MC_MODE(x)		    _SB_GETVALUE(x, S_BCM1480_MC_MODE, M_BCM1480_MC_MODE)
+#define V_BCM1480_MC_MODE_DEFAULT	    V_BCM1480_MC_MODE(0)
+
+#define S_BCM1480_MC_DRAM_TYPE		    32
+#define M_BCM1480_MC_DRAM_TYPE		    _SB_MAKEMASK(4, S_BCM1480_MC_DRAM_TYPE)
+#define V_BCM1480_MC_DRAM_TYPE(x)	    _SB_MAKEVALUE(x, S_BCM1480_MC_DRAM_TYPE)
+#define G_BCM1480_MC_DRAM_TYPE(x)	    _SB_GETVALUE(x, S_BCM1480_MC_DRAM_TYPE, M_BCM1480_MC_DRAM_TYPE)
+
+#define K_BCM1480_MC_DRAM_TYPE_JEDEC	    0
+#define K_BCM1480_MC_DRAM_TYPE_FCRAM	    1
+
+#if SIBYTE_HDR_FEATURE(1480, PASS2)
+#define K_BCM1480_MC_DRAM_TYPE_DDR2	    2
+#endif
+
+#define K_BCM1480_MC_DRAM_TYPE_DDR2_PASS1   0
+
+#define V_BCM1480_MC_DRAM_TYPE_JEDEC	    V_BCM1480_MC_DRAM_TYPE(K_BCM1480_MC_DRAM_TYPE_JEDEC)
+#define V_BCM1480_MC_DRAM_TYPE_FCRAM	    V_BCM1480_MC_DRAM_TYPE(K_BCM1480_MC_DRAM_TYPE_FCRAM)
+
+#if SIBYTE_HDR_FEATURE(1480, PASS2)
+#define V_BCM1480_MC_DRAM_TYPE_DDR2	    V_BCM1480_MC_DRAM_TYPE(K_BCM1480_MC_DRAM_TYPE_DDR2)
+#endif
+
+#define M_BCM1480_MC_GANGED		    _SB_MAKEMASK1(36)
+#define M_BCM1480_MC_BY9_INTF		    _SB_MAKEMASK1(37)
+#define M_BCM1480_MC_FORCE_ECC64	    _SB_MAKEMASK1(38)
+#define M_BCM1480_MC_ECC_DISABLE	    _SB_MAKEMASK1(39)
+
+#define S_BCM1480_MC_PG_POLICY		    40
+#define M_BCM1480_MC_PG_POLICY		    _SB_MAKEMASK(2, S_BCM1480_MC_PG_POLICY)
+#define V_BCM1480_MC_PG_POLICY(x)	    _SB_MAKEVALUE(x, S_BCM1480_MC_PG_POLICY)
+#define G_BCM1480_MC_PG_POLICY(x)	    _SB_GETVALUE(x, S_BCM1480_MC_PG_POLICY, M_BCM1480_MC_PG_POLICY)
+
+#define K_BCM1480_MC_PG_POLICY_CLOSED	    0
+#define K_BCM1480_MC_PG_POLICY_CAS_TIME_CHK 1
+
+#define V_BCM1480_MC_PG_POLICY_CLOSED	    V_BCM1480_MC_PG_POLICY(K_BCM1480_MC_PG_POLICY_CLOSED)
+#define V_BCM1480_MC_PG_POLICY_CAS_TIME_CHK V_BCM1480_MC_PG_POLICY(K_BCM1480_MC_PG_POLICY_CAS_TIME_CHK)
+
+#if SIBYTE_HDR_FEATURE(1480, PASS2)
+#define M_BCM1480_MC_2T_CMD		    _SB_MAKEMASK1(42)
+#define M_BCM1480_MC_ECC_COR_DIS	    _SB_MAKEMASK1(43)
+#endif
+
+#define V_BCM1480_MC_DRAMMODE_DEFAULT	V_BCM1480_MC_EMODE_DEFAULT | V_BCM1480_MC_MODE_DEFAULT | V_BCM1480_MC_DRAM_TYPE_JEDEC | \
+				V_BCM1480_MC_PG_POLICY(K_BCM1480_MC_PG_POLICY_CAS_TIME_CHK)
+
+/*
+ * Memory Clock Configuration Register (Table 92)
+ */
+
+#define S_BCM1480_MC_CLK_RATIO		    0
+#define M_BCM1480_MC_CLK_RATIO		    _SB_MAKEMASK(6, S_BCM1480_MC_CLK_RATIO)
+#define V_BCM1480_MC_CLK_RATIO(x)	    _SB_MAKEVALUE(x, S_BCM1480_MC_CLK_RATIO)
+#define G_BCM1480_MC_CLK_RATIO(x)	    _SB_GETVALUE(x, S_BCM1480_MC_CLK_RATIO, M_BCM1480_MC_CLK_RATIO)
+
+#define V_BCM1480_MC_CLK_RATIO_DEFAULT	    V_BCM1480_MC_CLK_RATIO(10)
+
+#define S_BCM1480_MC_REF_RATE		    8
+#define M_BCM1480_MC_REF_RATE		    _SB_MAKEMASK(8, S_BCM1480_MC_REF_RATE)
+#define V_BCM1480_MC_REF_RATE(x)	    _SB_MAKEVALUE(x, S_BCM1480_MC_REF_RATE)
+#define G_BCM1480_MC_REF_RATE(x)	    _SB_GETVALUE(x, S_BCM1480_MC_REF_RATE, M_BCM1480_MC_REF_RATE)
+
+#define K_BCM1480_MC_REF_RATE_100MHz	    0x31
+#define K_BCM1480_MC_REF_RATE_200MHz	    0x62
+#define K_BCM1480_MC_REF_RATE_400MHz	    0xC4
+
+#define V_BCM1480_MC_REF_RATE_100MHz	    V_BCM1480_MC_REF_RATE(K_BCM1480_MC_REF_RATE_100MHz)
+#define V_BCM1480_MC_REF_RATE_200MHz	    V_BCM1480_MC_REF_RATE(K_BCM1480_MC_REF_RATE_200MHz)
+#define V_BCM1480_MC_REF_RATE_400MHz	    V_BCM1480_MC_REF_RATE(K_BCM1480_MC_REF_RATE_400MHz)
+#define V_BCM1480_MC_REF_RATE_DEFAULT	    V_BCM1480_MC_REF_RATE_400MHz
+
+#if SIBYTE_HDR_FEATURE(1480, PASS2)
+#define M_BCM1480_MC_AUTO_REF_DIS	    _SB_MAKEMASK1(16)
+#endif
+
+/*
+ * ODT Register (Table 99)
+ */
+
+#if SIBYTE_HDR_FEATURE(1480, PASS2)
+#define M_BCM1480_MC_RD_ODT0_CS0	    _SB_MAKEMASK1(0)
+#define M_BCM1480_MC_RD_ODT0_CS2	    _SB_MAKEMASK1(1)
+#define M_BCM1480_MC_RD_ODT0_CS4	    _SB_MAKEMASK1(2)
+#define M_BCM1480_MC_RD_ODT0_CS6	    _SB_MAKEMASK1(3)
+#define M_BCM1480_MC_WR_ODT0_CS0	    _SB_MAKEMASK1(4)
+#define M_BCM1480_MC_WR_ODT0_CS2	    _SB_MAKEMASK1(5)
+#define M_BCM1480_MC_WR_ODT0_CS4	    _SB_MAKEMASK1(6)
+#define M_BCM1480_MC_WR_ODT0_CS6	    _SB_MAKEMASK1(7)
+#define M_BCM1480_MC_RD_ODT2_CS0	    _SB_MAKEMASK1(8)
+#define M_BCM1480_MC_RD_ODT2_CS2	    _SB_MAKEMASK1(9)
+#define M_BCM1480_MC_RD_ODT2_CS4	    _SB_MAKEMASK1(10)
+#define M_BCM1480_MC_RD_ODT2_CS6	    _SB_MAKEMASK1(11)
+#define M_BCM1480_MC_WR_ODT2_CS0	    _SB_MAKEMASK1(12)
+#define M_BCM1480_MC_WR_ODT2_CS2	    _SB_MAKEMASK1(13)
+#define M_BCM1480_MC_WR_ODT2_CS4	    _SB_MAKEMASK1(14)
+#define M_BCM1480_MC_WR_ODT2_CS6	    _SB_MAKEMASK1(15)
+#define M_BCM1480_MC_RD_ODT4_CS0	    _SB_MAKEMASK1(16)
+#define M_BCM1480_MC_RD_ODT4_CS2	    _SB_MAKEMASK1(17)
+#define M_BCM1480_MC_RD_ODT4_CS4	    _SB_MAKEMASK1(18)
+#define M_BCM1480_MC_RD_ODT4_CS6	    _SB_MAKEMASK1(19)
+#define M_BCM1480_MC_WR_ODT4_CS0	    _SB_MAKEMASK1(20)
+#define M_BCM1480_MC_WR_ODT4_CS2	    _SB_MAKEMASK1(21)
+#define M_BCM1480_MC_WR_ODT4_CS4	    _SB_MAKEMASK1(22)
+#define M_BCM1480_MC_WR_ODT4_CS6	    _SB_MAKEMASK1(23)
+#define M_BCM1480_MC_RD_ODT6_CS0	    _SB_MAKEMASK1(24)
+#define M_BCM1480_MC_RD_ODT6_CS2	    _SB_MAKEMASK1(25)
+#define M_BCM1480_MC_RD_ODT6_CS4	    _SB_MAKEMASK1(26)
+#define M_BCM1480_MC_RD_ODT6_CS6	    _SB_MAKEMASK1(27)
+#define M_BCM1480_MC_WR_ODT6_CS0	    _SB_MAKEMASK1(28)
+#define M_BCM1480_MC_WR_ODT6_CS2	    _SB_MAKEMASK1(29)
+#define M_BCM1480_MC_WR_ODT6_CS4	    _SB_MAKEMASK1(30)
+#define M_BCM1480_MC_WR_ODT6_CS6	    _SB_MAKEMASK1(31)
+
+#define M_BCM1480_MC_CS_ODD_ODT_EN	    _SB_MAKEMASK1(32)
+
+#define S_BCM1480_MC_ODT0		    0
+#define M_BCM1480_MC_ODT0		    _SB_MAKEMASK(8, S_BCM1480_MC_ODT0)
+#define V_BCM1480_MC_ODT0(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_ODT0)
+
+#define S_BCM1480_MC_ODT2		    8
+#define M_BCM1480_MC_ODT2		    _SB_MAKEMASK(8, S_BCM1480_MC_ODT2)
+#define V_BCM1480_MC_ODT2(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_ODT2)
+
+#define S_BCM1480_MC_ODT4		    16
+#define M_BCM1480_MC_ODT4		    _SB_MAKEMASK(8, S_BCM1480_MC_ODT4)
+#define V_BCM1480_MC_ODT4(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_ODT4)
+
+#define S_BCM1480_MC_ODT6		    24
+#define M_BCM1480_MC_ODT6		    _SB_MAKEMASK(8, S_BCM1480_MC_ODT6)
+#define V_BCM1480_MC_ODT6(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_ODT6)
+#endif
+
+/*
+ * Memory DLL Configuration Register (Table 93)
+ */
+
+#define S_BCM1480_MC_ADDR_COARSE_ADJ	     0
+#define M_BCM1480_MC_ADDR_COARSE_ADJ	     _SB_MAKEMASK(6, S_BCM1480_MC_ADDR_COARSE_ADJ)
+#define V_BCM1480_MC_ADDR_COARSE_ADJ(x)	     _SB_MAKEVALUE(x, S_BCM1480_MC_ADDR_COARSE_ADJ)
+#define G_BCM1480_MC_ADDR_COARSE_ADJ(x)	     _SB_GETVALUE(x, S_BCM1480_MC_ADDR_COARSE_ADJ, M_BCM1480_MC_ADDR_COARSE_ADJ)
+#define V_BCM1480_MC_ADDR_COARSE_ADJ_DEFAULT V_BCM1480_MC_ADDR_COARSE_ADJ(0x0)
+
+#if SIBYTE_HDR_FEATURE(1480, PASS2)
+#define S_BCM1480_MC_ADDR_FREQ_RANGE		8
+#define M_BCM1480_MC_ADDR_FREQ_RANGE		_SB_MAKEMASK(4, S_BCM1480_MC_ADDR_FREQ_RANGE)
+#define V_BCM1480_MC_ADDR_FREQ_RANGE(x)		_SB_MAKEVALUE(x, S_BCM1480_MC_ADDR_FREQ_RANGE)
+#define G_BCM1480_MC_ADDR_FREQ_RANGE(x)		_SB_GETVALUE(x, S_BCM1480_MC_ADDR_FREQ_RANGE, M_BCM1480_MC_ADDR_FREQ_RANGE)
+#define V_BCM1480_MC_ADDR_FREQ_RANGE_DEFAULT	V_BCM1480_MC_ADDR_FREQ_RANGE(0x4)
+#endif
+
+#define S_BCM1480_MC_ADDR_FINE_ADJ	    8
+#define M_BCM1480_MC_ADDR_FINE_ADJ	    _SB_MAKEMASK(4, S_BCM1480_MC_ADDR_FINE_ADJ)
+#define V_BCM1480_MC_ADDR_FINE_ADJ(x)	    _SB_MAKEVALUE(x, S_BCM1480_MC_ADDR_FINE_ADJ)
+#define G_BCM1480_MC_ADDR_FINE_ADJ(x)	    _SB_GETVALUE(x, S_BCM1480_MC_ADDR_FINE_ADJ, M_BCM1480_MC_ADDR_FINE_ADJ)
+#define V_BCM1480_MC_ADDR_FINE_ADJ_DEFAULT  V_BCM1480_MC_ADDR_FINE_ADJ(0x8)
+
+#define S_BCM1480_MC_DQI_COARSE_ADJ	    16
+#define M_BCM1480_MC_DQI_COARSE_ADJ	    _SB_MAKEMASK(6, S_BCM1480_MC_DQI_COARSE_ADJ)
+#define V_BCM1480_MC_DQI_COARSE_ADJ(x)	    _SB_MAKEVALUE(x, S_BCM1480_MC_DQI_COARSE_ADJ)
+#define G_BCM1480_MC_DQI_COARSE_ADJ(x)	    _SB_GETVALUE(x, S_BCM1480_MC_DQI_COARSE_ADJ, M_BCM1480_MC_DQI_COARSE_ADJ)
+#define V_BCM1480_MC_DQI_COARSE_ADJ_DEFAULT V_BCM1480_MC_DQI_COARSE_ADJ(0x0)
+
+#if SIBYTE_HDR_FEATURE(1480, PASS2)
+#define S_BCM1480_MC_DQI_FREQ_RANGE		24
+#define M_BCM1480_MC_DQI_FREQ_RANGE		_SB_MAKEMASK(4, S_BCM1480_MC_DQI_FREQ_RANGE)
+#define V_BCM1480_MC_DQI_FREQ_RANGE(x)		_SB_MAKEVALUE(x, S_BCM1480_MC_DQI_FREQ_RANGE)
+#define G_BCM1480_MC_DQI_FREQ_RANGE(x)		_SB_GETVALUE(x, S_BCM1480_MC_DQI_FREQ_RANGE, M_BCM1480_MC_DQI_FREQ_RANGE)
+#define V_BCM1480_MC_DQI_FREQ_RANGE_DEFAULT	V_BCM1480_MC_DQI_FREQ_RANGE(0x4)
+#endif
+
+#define S_BCM1480_MC_DQI_FINE_ADJ	    24
+#define M_BCM1480_MC_DQI_FINE_ADJ	    _SB_MAKEMASK(4, S_BCM1480_MC_DQI_FINE_ADJ)
+#define V_BCM1480_MC_DQI_FINE_ADJ(x)	    _SB_MAKEVALUE(x, S_BCM1480_MC_DQI_FINE_ADJ)
+#define G_BCM1480_MC_DQI_FINE_ADJ(x)	    _SB_GETVALUE(x, S_BCM1480_MC_DQI_FINE_ADJ, M_BCM1480_MC_DQI_FINE_ADJ)
+#define V_BCM1480_MC_DQI_FINE_ADJ_DEFAULT   V_BCM1480_MC_DQI_FINE_ADJ(0x8)
+
+#define S_BCM1480_MC_DQO_COARSE_ADJ	    32
+#define M_BCM1480_MC_DQO_COARSE_ADJ	    _SB_MAKEMASK(6, S_BCM1480_MC_DQO_COARSE_ADJ)
+#define V_BCM1480_MC_DQO_COARSE_ADJ(x)	    _SB_MAKEVALUE(x, S_BCM1480_MC_DQO_COARSE_ADJ)
+#define G_BCM1480_MC_DQO_COARSE_ADJ(x)	    _SB_GETVALUE(x, S_BCM1480_MC_DQO_COARSE_ADJ, M_BCM1480_MC_DQO_COARSE_ADJ)
+#define V_BCM1480_MC_DQO_COARSE_ADJ_DEFAULT V_BCM1480_MC_DQO_COARSE_ADJ(0x0)
+
+#if SIBYTE_HDR_FEATURE(1480, PASS2)
+#define S_BCM1480_MC_DQO_FREQ_RANGE		40
+#define M_BCM1480_MC_DQO_FREQ_RANGE		_SB_MAKEMASK(4, S_BCM1480_MC_DQO_FREQ_RANGE)
+#define V_BCM1480_MC_DQO_FREQ_RANGE(x)		_SB_MAKEVALUE(x, S_BCM1480_MC_DQO_FREQ_RANGE)
+#define G_BCM1480_MC_DQO_FREQ_RANGE(x)		_SB_GETVALUE(x, S_BCM1480_MC_DQO_FREQ_RANGE, M_BCM1480_MC_DQO_FREQ_RANGE)
+#define V_BCM1480_MC_DQO_FREQ_RANGE_DEFAULT	V_BCM1480_MC_DQO_FREQ_RANGE(0x4)
+#endif
+
+#define S_BCM1480_MC_DQO_FINE_ADJ	    40
+#define M_BCM1480_MC_DQO_FINE_ADJ	    _SB_MAKEMASK(4, S_BCM1480_MC_DQO_FINE_ADJ)
+#define V_BCM1480_MC_DQO_FINE_ADJ(x)	    _SB_MAKEVALUE(x, S_BCM1480_MC_DQO_FINE_ADJ)
+#define G_BCM1480_MC_DQO_FINE_ADJ(x)	    _SB_GETVALUE(x, S_BCM1480_MC_DQO_FINE_ADJ, M_BCM1480_MC_DQO_FINE_ADJ)
+#define V_BCM1480_MC_DQO_FINE_ADJ_DEFAULT   V_BCM1480_MC_DQO_FINE_ADJ(0x8)
+
+#if SIBYTE_HDR_FEATURE(1480, PASS2)
+#define S_BCM1480_MC_DLL_PDSEL		  44
+#define M_BCM1480_MC_DLL_PDSEL		  _SB_MAKEMASK(2, S_BCM1480_MC_DLL_PDSEL)
+#define V_BCM1480_MC_DLL_PDSEL(x)	  _SB_MAKEVALUE(x, S_BCM1480_MC_DLL_PDSEL)
+#define G_BCM1480_MC_DLL_PDSEL(x)	  _SB_GETVALUE(x, S_BCM1480_MC_DLL_PDSEL, M_BCM1480_MC_DLL_PDSEL)
+#define V_BCM1480_MC_DLL_DEFAULT_PDSEL	  V_BCM1480_MC_DLL_PDSEL(0x0)
+
+#define M_BCM1480_MC_DLL_REGBYPASS	  _SB_MAKEMASK1(46)
+#define M_BCM1480_MC_DQO_SHIFT		  _SB_MAKEMASK1(47)
+#endif
+
+#define S_BCM1480_MC_DLL_DEFAULT	   48
+#define M_BCM1480_MC_DLL_DEFAULT	   _SB_MAKEMASK(6, S_BCM1480_MC_DLL_DEFAULT)
+#define V_BCM1480_MC_DLL_DEFAULT(x)	   _SB_MAKEVALUE(x, S_BCM1480_MC_DLL_DEFAULT)
+#define G_BCM1480_MC_DLL_DEFAULT(x)	   _SB_GETVALUE(x, S_BCM1480_MC_DLL_DEFAULT, M_BCM1480_MC_DLL_DEFAULT)
+#define V_BCM1480_MC_DLL_DEFAULT_DEFAULT   V_BCM1480_MC_DLL_DEFAULT(0x10)
+
+#if SIBYTE_HDR_FEATURE(1480, PASS2)
+#define S_BCM1480_MC_DLL_REGCTRL	  54
+#define M_BCM1480_MC_DLL_REGCTRL	  _SB_MAKEMASK(2, S_BCM1480_MC_DLL_REGCTRL)
+#define V_BCM1480_MC_DLL_REGCTRL(x)	  _SB_MAKEVALUE(x, S_BCM1480_MC_DLL_REGCTRL)
+#define G_BCM1480_MC_DLL_REGCTRL(x)	  _SB_GETVALUE(x, S_BCM1480_MC_DLL_REGCTRL, M_BCM1480_MC_DLL_REGCTRL)
+#define V_BCM1480_MC_DLL_DEFAULT_REGCTRL  V_BCM1480_MC_DLL_REGCTRL(0x0)
+#endif
+
+#if SIBYTE_HDR_FEATURE(1480, PASS2)
+#define S_BCM1480_MC_DLL_FREQ_RANGE		56
+#define M_BCM1480_MC_DLL_FREQ_RANGE		_SB_MAKEMASK(4, S_BCM1480_MC_DLL_FREQ_RANGE)
+#define V_BCM1480_MC_DLL_FREQ_RANGE(x)		_SB_MAKEVALUE(x, S_BCM1480_MC_DLL_FREQ_RANGE)
+#define G_BCM1480_MC_DLL_FREQ_RANGE(x)		_SB_GETVALUE(x, S_BCM1480_MC_DLL_FREQ_RANGE, M_BCM1480_MC_DLL_FREQ_RANGE)
+#define V_BCM1480_MC_DLL_FREQ_RANGE_DEFAULT	V_BCM1480_MC_DLL_FREQ_RANGE(0x4)
+#endif
+
+#define S_BCM1480_MC_DLL_STEP_SIZE	    56
+#define M_BCM1480_MC_DLL_STEP_SIZE	    _SB_MAKEMASK(4, S_BCM1480_MC_DLL_STEP_SIZE)
+#define V_BCM1480_MC_DLL_STEP_SIZE(x)	    _SB_MAKEVALUE(x, S_BCM1480_MC_DLL_STEP_SIZE)
+#define G_BCM1480_MC_DLL_STEP_SIZE(x)	    _SB_GETVALUE(x, S_BCM1480_MC_DLL_STEP_SIZE, M_BCM1480_MC_DLL_STEP_SIZE)
+#define V_BCM1480_MC_DLL_STEP_SIZE_DEFAULT  V_BCM1480_MC_DLL_STEP_SIZE(0x8)
+
+#if SIBYTE_HDR_FEATURE(1480, PASS2)
+#define S_BCM1480_MC_DLL_BGCTRL	  60
+#define M_BCM1480_MC_DLL_BGCTRL		  _SB_MAKEMASK(2, S_BCM1480_MC_DLL_BGCTRL)
+#define V_BCM1480_MC_DLL_BGCTRL(x)	 _SB_MAKEVALUE(x, S_BCM1480_MC_DLL_BGCTRL)
+#define G_BCM1480_MC_DLL_BGCTRL(x)	 _SB_GETVALUE(x, S_BCM1480_MC_DLL_BGCTRL, M_BCM1480_MC_DLL_BGCTRL)
+#define V_BCM1480_MC_DLL_DEFAULT_BGCTRL	 V_BCM1480_MC_DLL_BGCTRL(0x0)
+#endif
+
+#define M_BCM1480_MC_DLL_BYPASS		    _SB_MAKEMASK1(63)
+
+/*
+ * Memory Drive Configuration Register (Table 94)
+ */
+
+#define S_BCM1480_MC_RTT_BYP_PULLDOWN	    0
+#define M_BCM1480_MC_RTT_BYP_PULLDOWN	    _SB_MAKEMASK(3, S_BCM1480_MC_RTT_BYP_PULLDOWN)
+#define V_BCM1480_MC_RTT_BYP_PULLDOWN(x)    _SB_MAKEVALUE(x, S_BCM1480_MC_RTT_BYP_PULLDOWN)
+#define G_BCM1480_MC_RTT_BYP_PULLDOWN(x)    _SB_GETVALUE(x, S_BCM1480_MC_RTT_BYP_PULLDOWN, M_BCM1480_MC_RTT_BYP_PULLDOWN)
+
+#define S_BCM1480_MC_RTT_BYP_PULLUP	    6
+#define M_BCM1480_MC_RTT_BYP_PULLUP	    _SB_MAKEMASK(3, S_BCM1480_MC_RTT_BYP_PULLUP)
+#define V_BCM1480_MC_RTT_BYP_PULLUP(x)	    _SB_MAKEVALUE(x, S_BCM1480_MC_RTT_BYP_PULLUP)
+#define G_BCM1480_MC_RTT_BYP_PULLUP(x)	    _SB_GETVALUE(x, S_BCM1480_MC_RTT_BYP_PULLUP, M_BCM1480_MC_RTT_BYP_PULLUP)
+
+#define M_BCM1480_MC_RTT_BYPASS		    _SB_MAKEMASK1(8)
+#define M_BCM1480_MC_RTT_COMP_MOV_AVG	    _SB_MAKEMASK1(9)
+
+#define S_BCM1480_MC_PVT_BYP_C1_PULLDOWN    10
+#define M_BCM1480_MC_PVT_BYP_C1_PULLDOWN    _SB_MAKEMASK(4, S_BCM1480_MC_PVT_BYP_C1_PULLDOWN)
+#define V_BCM1480_MC_PVT_BYP_C1_PULLDOWN(x) _SB_MAKEVALUE(x, S_BCM1480_MC_PVT_BYP_C1_PULLDOWN)
+#define G_BCM1480_MC_PVT_BYP_C1_PULLDOWN(x) _SB_GETVALUE(x, S_BCM1480_MC_PVT_BYP_C1_PULLDOWN, M_BCM1480_MC_PVT_BYP_C1_PULLDOWN)
+
+#define S_BCM1480_MC_PVT_BYP_C1_PULLUP	    15
+#define M_BCM1480_MC_PVT_BYP_C1_PULLUP	    _SB_MAKEMASK(4, S_BCM1480_MC_PVT_BYP_C1_PULLUP)
+#define V_BCM1480_MC_PVT_BYP_C1_PULLUP(x)   _SB_MAKEVALUE(x, S_BCM1480_MC_PVT_BYP_C1_PULLUP)
+#define G_BCM1480_MC_PVT_BYP_C1_PULLUP(x)   _SB_GETVALUE(x, S_BCM1480_MC_PVT_BYP_C1_PULLUP, M_BCM1480_MC_PVT_BYP_C1_PULLUP)
+
+#define S_BCM1480_MC_PVT_BYP_C2_PULLDOWN    20
+#define M_BCM1480_MC_PVT_BYP_C2_PULLDOWN    _SB_MAKEMASK(4, S_BCM1480_MC_PVT_BYP_C2_PULLDOWN)
+#define V_BCM1480_MC_PVT_BYP_C2_PULLDOWN(x) _SB_MAKEVALUE(x, S_BCM1480_MC_PVT_BYP_C2_PULLDOWN)
+#define G_BCM1480_MC_PVT_BYP_C2_PULLDOWN(x) _SB_GETVALUE(x, S_BCM1480_MC_PVT_BYP_C2_PULLDOWN, M_BCM1480_MC_PVT_BYP_C2_PULLDOWN)
+
+#define S_BCM1480_MC_PVT_BYP_C2_PULLUP	    25
+#define M_BCM1480_MC_PVT_BYP_C2_PULLUP	    _SB_MAKEMASK(4, S_BCM1480_MC_PVT_BYP_C2_PULLUP)
+#define V_BCM1480_MC_PVT_BYP_C2_PULLUP(x)   _SB_MAKEVALUE(x, S_BCM1480_MC_PVT_BYP_C2_PULLUP)
+#define G_BCM1480_MC_PVT_BYP_C2_PULLUP(x)   _SB_GETVALUE(x, S_BCM1480_MC_PVT_BYP_C2_PULLUP, M_BCM1480_MC_PVT_BYP_C2_PULLUP)
+
+#define M_BCM1480_MC_PVT_BYPASS		    _SB_MAKEMASK1(30)
+#define M_BCM1480_MC_PVT_COMP_MOV_AVG	    _SB_MAKEMASK1(31)
+
+#define M_BCM1480_MC_CLK_CLASS		    _SB_MAKEMASK1(34)
+#define M_BCM1480_MC_DATA_CLASS		    _SB_MAKEMASK1(35)
+#define M_BCM1480_MC_ADDR_CLASS		    _SB_MAKEMASK1(36)
+
+#define M_BCM1480_MC_DQ_ODT_75		    _SB_MAKEMASK1(37)
+#define M_BCM1480_MC_DQ_ODT_150		    _SB_MAKEMASK1(38)
+#define M_BCM1480_MC_DQS_ODT_75		    _SB_MAKEMASK1(39)
+#define M_BCM1480_MC_DQS_ODT_150	    _SB_MAKEMASK1(40)
+#define M_BCM1480_MC_DQS_DIFF		    _SB_MAKEMASK1(41)
+
+/*
+ * ECC Test Data Register (Table 95)
+ */
+
+#define S_BCM1480_MC_DATA_INVERT	    0
+#define M_DATA_ECC_INVERT	    _SB_MAKEMASK(64, S_BCM1480_MC_ECC_INVERT)
+
+/*
+ * ECC Test ECC Register (Table 96)
+ */
+
+#define S_BCM1480_MC_ECC_INVERT		    0
+#define M_BCM1480_MC_ECC_INVERT		    _SB_MAKEMASK(8, S_BCM1480_MC_ECC_INVERT)
+
+/*
+ * SDRAM Timing Register  (Table 97)
+ */
+
+#define S_BCM1480_MC_tRCD		    0
+#define M_BCM1480_MC_tRCD		    _SB_MAKEMASK(4, S_BCM1480_MC_tRCD)
+#define V_BCM1480_MC_tRCD(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_tRCD)
+#define G_BCM1480_MC_tRCD(x)		    _SB_GETVALUE(x, S_BCM1480_MC_tRCD, M_BCM1480_MC_tRCD)
+#define K_BCM1480_MC_tRCD_DEFAULT	    3
+#define V_BCM1480_MC_tRCD_DEFAULT	    V_BCM1480_MC_tRCD(K_BCM1480_MC_tRCD_DEFAULT)
+
+#define S_BCM1480_MC_tCL		    4
+#define M_BCM1480_MC_tCL		    _SB_MAKEMASK(4, S_BCM1480_MC_tCL)
+#define V_BCM1480_MC_tCL(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_tCL)
+#define G_BCM1480_MC_tCL(x)		    _SB_GETVALUE(x, S_BCM1480_MC_tCL, M_BCM1480_MC_tCL)
+#define K_BCM1480_MC_tCL_DEFAULT	    2
+#define V_BCM1480_MC_tCL_DEFAULT	    V_BCM1480_MC_tCL(K_BCM1480_MC_tCL_DEFAULT)
+
+#define M_BCM1480_MC_tCrDh		    _SB_MAKEMASK1(8)
+
+#define S_BCM1480_MC_tWR		    9
+#define M_BCM1480_MC_tWR		    _SB_MAKEMASK(3, S_BCM1480_MC_tWR)
+#define V_BCM1480_MC_tWR(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_tWR)
+#define G_BCM1480_MC_tWR(x)		    _SB_GETVALUE(x, S_BCM1480_MC_tWR, M_BCM1480_MC_tWR)
+#define K_BCM1480_MC_tWR_DEFAULT	    2
+#define V_BCM1480_MC_tWR_DEFAULT	    V_BCM1480_MC_tWR(K_BCM1480_MC_tWR_DEFAULT)
+
+#define S_BCM1480_MC_tCwD		    12
+#define M_BCM1480_MC_tCwD		    _SB_MAKEMASK(4, S_BCM1480_MC_tCwD)
+#define V_BCM1480_MC_tCwD(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_tCwD)
+#define G_BCM1480_MC_tCwD(x)		    _SB_GETVALUE(x, S_BCM1480_MC_tCwD, M_BCM1480_MC_tCwD)
+#define K_BCM1480_MC_tCwD_DEFAULT	    1
+#define V_BCM1480_MC_tCwD_DEFAULT	    V_BCM1480_MC_tCwD(K_BCM1480_MC_tCwD_DEFAULT)
+
+#define S_BCM1480_MC_tRP		    16
+#define M_BCM1480_MC_tRP		    _SB_MAKEMASK(4, S_BCM1480_MC_tRP)
+#define V_BCM1480_MC_tRP(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_tRP)
+#define G_BCM1480_MC_tRP(x)		    _SB_GETVALUE(x, S_BCM1480_MC_tRP, M_BCM1480_MC_tRP)
+#define K_BCM1480_MC_tRP_DEFAULT	    4
+#define V_BCM1480_MC_tRP_DEFAULT	    V_BCM1480_MC_tRP(K_BCM1480_MC_tRP_DEFAULT)
+
+#define S_BCM1480_MC_tRRD		    20
+#define M_BCM1480_MC_tRRD		    _SB_MAKEMASK(4, S_BCM1480_MC_tRRD)
+#define V_BCM1480_MC_tRRD(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_tRRD)
+#define G_BCM1480_MC_tRRD(x)		    _SB_GETVALUE(x, S_BCM1480_MC_tRRD, M_BCM1480_MC_tRRD)
+#define K_BCM1480_MC_tRRD_DEFAULT	    2
+#define V_BCM1480_MC_tRRD_DEFAULT	    V_BCM1480_MC_tRRD(K_BCM1480_MC_tRRD_DEFAULT)
+
+#define S_BCM1480_MC_tRCw		    24
+#define M_BCM1480_MC_tRCw		    _SB_MAKEMASK(5, S_BCM1480_MC_tRCw)
+#define V_BCM1480_MC_tRCw(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_tRCw)
+#define G_BCM1480_MC_tRCw(x)		    _SB_GETVALUE(x, S_BCM1480_MC_tRCw, M_BCM1480_MC_tRCw)
+#define K_BCM1480_MC_tRCw_DEFAULT	    10
+#define V_BCM1480_MC_tRCw_DEFAULT	    V_BCM1480_MC_tRCw(K_BCM1480_MC_tRCw_DEFAULT)
+
+#define S_BCM1480_MC_tRCr		    32
+#define M_BCM1480_MC_tRCr		    _SB_MAKEMASK(5, S_BCM1480_MC_tRCr)
+#define V_BCM1480_MC_tRCr(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_tRCr)
+#define G_BCM1480_MC_tRCr(x)		    _SB_GETVALUE(x, S_BCM1480_MC_tRCr, M_BCM1480_MC_tRCr)
+#define K_BCM1480_MC_tRCr_DEFAULT	    9
+#define V_BCM1480_MC_tRCr_DEFAULT	    V_BCM1480_MC_tRCr(K_BCM1480_MC_tRCr_DEFAULT)
+
+#if SIBYTE_HDR_FEATURE(1480, PASS2)
+#define S_BCM1480_MC_tFAW		    40
+#define M_BCM1480_MC_tFAW		    _SB_MAKEMASK(6, S_BCM1480_MC_tFAW)
+#define V_BCM1480_MC_tFAW(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_tFAW)
+#define G_BCM1480_MC_tFAW(x)		    _SB_GETVALUE(x, S_BCM1480_MC_tFAW, M_BCM1480_MC_tFAW)
+#define K_BCM1480_MC_tFAW_DEFAULT	    0
+#define V_BCM1480_MC_tFAW_DEFAULT	    V_BCM1480_MC_tFAW(K_BCM1480_MC_tFAW_DEFAULT)
+#endif
+
+#define S_BCM1480_MC_tRFC		    48
+#define M_BCM1480_MC_tRFC		    _SB_MAKEMASK(7, S_BCM1480_MC_tRFC)
+#define V_BCM1480_MC_tRFC(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_tRFC)
+#define G_BCM1480_MC_tRFC(x)		    _SB_GETVALUE(x, S_BCM1480_MC_tRFC, M_BCM1480_MC_tRFC)
+#define K_BCM1480_MC_tRFC_DEFAULT	    12
+#define V_BCM1480_MC_tRFC_DEFAULT	    V_BCM1480_MC_tRFC(K_BCM1480_MC_tRFC_DEFAULT)
+
+#define S_BCM1480_MC_tFIFO		    56
+#define M_BCM1480_MC_tFIFO		    _SB_MAKEMASK(2, S_BCM1480_MC_tFIFO)
+#define V_BCM1480_MC_tFIFO(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_tFIFO)
+#define G_BCM1480_MC_tFIFO(x)		    _SB_GETVALUE(x, S_BCM1480_MC_tFIFO, M_BCM1480_MC_tFIFO)
+#define K_BCM1480_MC_tFIFO_DEFAULT	    0
+#define V_BCM1480_MC_tFIFO_DEFAULT	    V_BCM1480_MC_tFIFO(K_BCM1480_MC_tFIFO_DEFAULT)
+
+#define S_BCM1480_MC_tW2R		   58
+#define M_BCM1480_MC_tW2R		   _SB_MAKEMASK(2, S_BCM1480_MC_tW2R)
+#define V_BCM1480_MC_tW2R(x)		   _SB_MAKEVALUE(x, S_BCM1480_MC_tW2R)
+#define G_BCM1480_MC_tW2R(x)		   _SB_GETVALUE(x, S_BCM1480_MC_tW2R, M_BCM1480_MC_tW2R)
+#define K_BCM1480_MC_tW2R_DEFAULT	   1
+#define V_BCM1480_MC_tW2R_DEFAULT	   V_BCM1480_MC_tW2R(K_BCM1480_MC_tW2R_DEFAULT)
+
+#define S_BCM1480_MC_tR2W		   60
+#define M_BCM1480_MC_tR2W		   _SB_MAKEMASK(2, S_BCM1480_MC_tR2W)
+#define V_BCM1480_MC_tR2W(x)		   _SB_MAKEVALUE(x, S_BCM1480_MC_tR2W)
+#define G_BCM1480_MC_tR2W(x)		   _SB_GETVALUE(x, S_BCM1480_MC_tR2W, M_BCM1480_MC_tR2W)
+#define K_BCM1480_MC_tR2W_DEFAULT	   0
+#define V_BCM1480_MC_tR2W_DEFAULT	   V_BCM1480_MC_tR2W(K_BCM1480_MC_tR2W_DEFAULT)
+
+#define M_BCM1480_MC_tR2R		    _SB_MAKEMASK1(62)
+
+#define V_BCM1480_MC_TIMING_DEFAULT	    (M_BCM1480_MC_tR2R | \
+				     V_BCM1480_MC_tFIFO_DEFAULT | \
+				     V_BCM1480_MC_tR2W_DEFAULT | \
+				     V_BCM1480_MC_tW2R_DEFAULT | \
+				     V_BCM1480_MC_tRFC_DEFAULT | \
+				     V_BCM1480_MC_tRCr_DEFAULT | \
+				     V_BCM1480_MC_tRCw_DEFAULT | \
+				     V_BCM1480_MC_tRRD_DEFAULT | \
+				     V_BCM1480_MC_tRP_DEFAULT | \
+				     V_BCM1480_MC_tCwD_DEFAULT | \
+				     V_BCM1480_MC_tWR_DEFAULT | \
+				     M_BCM1480_MC_tCrDh | \
+				     V_BCM1480_MC_tCL_DEFAULT | \
+				     V_BCM1480_MC_tRCD_DEFAULT)
+
+/*
+ * SDRAM Timing Register 2
+ */
+
+#if SIBYTE_HDR_FEATURE(1480, PASS2)
+
+#define S_BCM1480_MC_tAL		   0
+#define M_BCM1480_MC_tAL		   _SB_MAKEMASK(4, S_BCM1480_MC_tAL)
+#define V_BCM1480_MC_tAL(x)		   _SB_MAKEVALUE(x, S_BCM1480_MC_tAL)
+#define G_BCM1480_MC_tAL(x)		   _SB_GETVALUE(x, S_BCM1480_MC_tAL, M_BCM1480_MC_tAL)
+#define K_BCM1480_MC_tAL_DEFAULT	   0
+#define V_BCM1480_MC_tAL_DEFAULT	   V_BCM1480_MC_tAL(K_BCM1480_MC_tAL_DEFAULT)
+
+#define S_BCM1480_MC_tRTP		    4
+#define M_BCM1480_MC_tRTP		    _SB_MAKEMASK(3, S_BCM1480_MC_tRTP)
+#define V_BCM1480_MC_tRTP(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_tRTP)
+#define G_BCM1480_MC_tRTP(x)		    _SB_GETVALUE(x, S_BCM1480_MC_tRTP, M_BCM1480_MC_tRTP)
+#define K_BCM1480_MC_tRTP_DEFAULT	    2
+#define V_BCM1480_MC_tRTP_DEFAULT	    V_BCM1480_MC_tRTP(K_BCM1480_MC_tRTP_DEFAULT)
+
+#define S_BCM1480_MC_tW2W		    8
+#define M_BCM1480_MC_tW2W		    _SB_MAKEMASK(2, S_BCM1480_MC_tW2W)
+#define V_BCM1480_MC_tW2W(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_tW2W)
+#define G_BCM1480_MC_tW2W(x)		    _SB_GETVALUE(x, S_BCM1480_MC_tW2W, M_BCM1480_MC_tW2W)
+#define K_BCM1480_MC_tW2W_DEFAULT	    0
+#define V_BCM1480_MC_tW2W_DEFAULT	    V_BCM1480_MC_tW2W(K_BCM1480_MC_tW2W_DEFAULT)
+
+#define S_BCM1480_MC_tRAP		    12
+#define M_BCM1480_MC_tRAP		   _SB_MAKEMASK(4, S_BCM1480_MC_tRAP)
+#define V_BCM1480_MC_tRAP(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_tRAP)
+#define G_BCM1480_MC_tRAP(x)		    _SB_GETVALUE(x, S_BCM1480_MC_tRAP, M_BCM1480_MC_tRAP)
+#define K_BCM1480_MC_tRAP_DEFAULT	    0
+#define V_BCM1480_MC_tRAP_DEFAULT	    V_BCM1480_MC_tRAP(K_BCM1480_MC_tRAP_DEFAULT)
+
+#endif
+
+
+
+/*
+ * Global Registers: single instances per BCM1480
+ */
+
+/*
+ * Global Configuration Register (Table 99)
+ */
+
+#define S_BCM1480_MC_BLK_SET_MARK	    8
+#define M_BCM1480_MC_BLK_SET_MARK	    _SB_MAKEMASK(4, S_BCM1480_MC_BLK_SET_MARK)
+#define V_BCM1480_MC_BLK_SET_MARK(x)	    _SB_MAKEVALUE(x, S_BCM1480_MC_BLK_SET_MARK)
+#define G_BCM1480_MC_BLK_SET_MARK(x)	    _SB_GETVALUE(x, S_BCM1480_MC_BLK_SET_MARK, M_BCM1480_MC_BLK_SET_MARK)
+
+#define S_BCM1480_MC_BLK_CLR_MARK	    12
+#define M_BCM1480_MC_BLK_CLR_MARK	    _SB_MAKEMASK(4, S_BCM1480_MC_BLK_CLR_MARK)
+#define V_BCM1480_MC_BLK_CLR_MARK(x)	    _SB_MAKEVALUE(x, S_BCM1480_MC_BLK_CLR_MARK)
+#define G_BCM1480_MC_BLK_CLR_MARK(x)	    _SB_GETVALUE(x, S_BCM1480_MC_BLK_CLR_MARK, M_BCM1480_MC_BLK_CLR_MARK)
+
+#define M_BCM1480_MC_PKT_PRIORITY	    _SB_MAKEMASK1(16)
+
+#define S_BCM1480_MC_MAX_AGE		    20
+#define M_BCM1480_MC_MAX_AGE		    _SB_MAKEMASK(4, S_BCM1480_MC_MAX_AGE)
+#define V_BCM1480_MC_MAX_AGE(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_MAX_AGE)
+#define G_BCM1480_MC_MAX_AGE(x)		    _SB_GETVALUE(x, S_BCM1480_MC_MAX_AGE, M_BCM1480_MC_MAX_AGE)
+
+#define M_BCM1480_MC_BERR_DISABLE	    _SB_MAKEMASK1(29)
+#define M_BCM1480_MC_FORCE_SEQ		    _SB_MAKEMASK1(30)
+#define M_BCM1480_MC_VGEN		    _SB_MAKEMASK1(32)
+
+#define S_BCM1480_MC_SLEW		    33
+#define M_BCM1480_MC_SLEW		    _SB_MAKEMASK(2, S_BCM1480_MC_SLEW)
+#define V_BCM1480_MC_SLEW(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_SLEW)
+#define G_BCM1480_MC_SLEW(x)		    _SB_GETVALUE(x, S_BCM1480_MC_SLEW, M_BCM1480_MC_SLEW)
+
+#define M_BCM1480_MC_SSTL_VOLTAGE	    _SB_MAKEMASK1(35)
+
+/*
+ * Global Channel Interleave Register (Table 100)
+ */
+
+#define S_BCM1480_MC_INTLV0		    0
+#define M_BCM1480_MC_INTLV0		    _SB_MAKEMASK(6, S_BCM1480_MC_INTLV0)
+#define V_BCM1480_MC_INTLV0(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_INTLV0)
+#define G_BCM1480_MC_INTLV0(x)		    _SB_GETVALUE(x, S_BCM1480_MC_INTLV0, M_BCM1480_MC_INTLV0)
+
+#define S_BCM1480_MC_INTLV1		    8
+#define M_BCM1480_MC_INTLV1		    _SB_MAKEMASK(6, S_BCM1480_MC_INTLV1)
+#define V_BCM1480_MC_INTLV1(x)		    _SB_MAKEVALUE(x, S_BCM1480_MC_INTLV1)
+#define G_BCM1480_MC_INTLV1(x)		    _SB_GETVALUE(x, S_BCM1480_MC_INTLV1, M_BCM1480_MC_INTLV1)
+
+#define S_BCM1480_MC_INTLV_MODE		    16
+#define M_BCM1480_MC_INTLV_MODE		    _SB_MAKEMASK(3, S_BCM1480_MC_INTLV_MODE)
+#define V_BCM1480_MC_INTLV_MODE(x)	    _SB_MAKEVALUE(x, S_BCM1480_MC_INTLV_MODE)
+#define G_BCM1480_MC_INTLV_MODE(x)	    _SB_GETVALUE(x, S_BCM1480_MC_INTLV_MODE, M_BCM1480_MC_INTLV_MODE)
+
+#define K_BCM1480_MC_INTLV_MODE_NONE	    0x0
+#define K_BCM1480_MC_INTLV_MODE_01	    0x1
+#define K_BCM1480_MC_INTLV_MODE_23	    0x2
+#define K_BCM1480_MC_INTLV_MODE_01_23	    0x3
+#define K_BCM1480_MC_INTLV_MODE_0123	    0x4
+
+#define V_BCM1480_MC_INTLV_MODE_NONE	    V_BCM1480_MC_INTLV_MODE(K_BCM1480_MC_INTLV_MODE_NONE)
+#define V_BCM1480_MC_INTLV_MODE_01	    V_BCM1480_MC_INTLV_MODE(K_BCM1480_MC_INTLV_MODE_01)
+#define V_BCM1480_MC_INTLV_MODE_23	    V_BCM1480_MC_INTLV_MODE(K_BCM1480_MC_INTLV_MODE_23)
+#define V_BCM1480_MC_INTLV_MODE_01_23	    V_BCM1480_MC_INTLV_MODE(K_BCM1480_MC_INTLV_MODE_01_23)
+#define V_BCM1480_MC_INTLV_MODE_0123	    V_BCM1480_MC_INTLV_MODE(K_BCM1480_MC_INTLV_MODE_0123)
+
+/*
+ * ECC Status Register
+ */
+
+#define S_BCM1480_MC_ECC_ERR_ADDR	    0
+#define M_BCM1480_MC_ECC_ERR_ADDR	    _SB_MAKEMASK(37, S_BCM1480_MC_ECC_ERR_ADDR)
+#define V_BCM1480_MC_ECC_ERR_ADDR(x)	    _SB_MAKEVALUE(x, S_BCM1480_MC_ECC_ERR_ADDR)
+#define G_BCM1480_MC_ECC_ERR_ADDR(x)	    _SB_GETVALUE(x, S_BCM1480_MC_ECC_ERR_ADDR, M_BCM1480_MC_ECC_ERR_ADDR)
+
+#if SIBYTE_HDR_FEATURE(1480, PASS2)
+#define M_BCM1480_MC_ECC_ERR_RMW	    _SB_MAKEMASK1(60)
+#endif
+
+#define M_BCM1480_MC_ECC_MULT_ERR_DET	    _SB_MAKEMASK1(61)
+#define M_BCM1480_MC_ECC_UERR_DET	    _SB_MAKEMASK1(62)
+#define M_BCM1480_MC_ECC_CERR_DET	    _SB_MAKEMASK1(63)
+
+/*
+ * Global ECC Address Register (Table 102)
+ */
+
+#define S_BCM1480_MC_ECC_CORR_ADDR	    0
+#define M_BCM1480_MC_ECC_CORR_ADDR	    _SB_MAKEMASK(37, S_BCM1480_MC_ECC_CORR_ADDR)
+#define V_BCM1480_MC_ECC_CORR_ADDR(x)	    _SB_MAKEVALUE(x, S_BCM1480_MC_ECC_CORR_ADDR)
+#define G_BCM1480_MC_ECC_CORR_ADDR(x)	    _SB_GETVALUE(x, S_BCM1480_MC_ECC_CORR_ADDR, M_BCM1480_MC_ECC_CORR_ADDR)
+
+/*
+ * Global ECC Correction Register (Table 103)
+ */
+
+#define S_BCM1480_MC_ECC_CORRECT	    0
+#define M_BCM1480_MC_ECC_CORRECT	    _SB_MAKEMASK(64, S_BCM1480_MC_ECC_CORRECT)
+#define V_BCM1480_MC_ECC_CORRECT(x)	    _SB_MAKEVALUE(x, S_BCM1480_MC_ECC_CORRECT)
+#define G_BCM1480_MC_ECC_CORRECT(x)	    _SB_GETVALUE(x, S_BCM1480_MC_ECC_CORRECT, M_BCM1480_MC_ECC_CORRECT)
+
+/*
+ * Global ECC Performance Counters Control Register (Table 104)
+ */
+
+#define S_BCM1480_MC_CHANNEL_SELECT	    0
+#define M_BCM1480_MC_CHANNEL_SELECT	    _SB_MAKEMASK(4, S_BCM1480_MC_CHANNEL_SELECT)
+#define V_BCM1480_MC_CHANNEL_SELECT(x)	    _SB_MAKEVALUE(x, S_BCM1480_MC_CHANNEL_SELECT)
+#define G_BCM1480_MC_CHANNEL_SELECT(x)	    _SB_GETVALUE(x, S_BCM1480_MC_CHANNEL_SELECT, M_BCM1480_MC_CHANNEL_SELECT)
+#define K_BCM1480_MC_CHANNEL_SELECT_0	    0x1
+#define K_BCM1480_MC_CHANNEL_SELECT_1	    0x2
+#define K_BCM1480_MC_CHANNEL_SELECT_2	    0x4
+#define K_BCM1480_MC_CHANNEL_SELECT_3	    0x8
+
+#endif /* _BCM1480_MC_H */
diff --git a/arch/mips/include/asm/sibyte/bcm1480_regs.h b/arch/mips/include/asm/sibyte/bcm1480_regs.h
new file mode 100644
index 000000000..ef12ede26
--- /dev/null
+++ b/arch/mips/include/asm/sibyte/bcm1480_regs.h
@@ -0,0 +1,889 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*  *********************************************************************
+    *  BCM1255/BCM1280/BCM1455/BCM1480 Board Support Package
+    *
+    *  Register Definitions			File: bcm1480_regs.h
+    *
+    *  This module contains the addresses of the on-chip peripherals
+    *  on the BCM1280 and BCM1480.
+    *
+    *  BCM1480 specification level:  1X55_1X80-UM100-D4 (11/24/03)
+    *
+    *********************************************************************
+    *
+    *  Copyright 2000,2001,2002,2003
+    *  Broadcom Corporation. All rights reserved.
+    *
+    ********************************************************************* */
+
+#ifndef _BCM1480_REGS_H
+#define _BCM1480_REGS_H
+
+#include <asm/sibyte/sb1250_defs.h>
+
+/*  *********************************************************************
+    *  Pull in the BCM1250's registers since a great deal of the 1480's
+    *  functions are the same as the BCM1250.
+    ********************************************************************* */
+
+#include <asm/sibyte/sb1250_regs.h>
+
+
+/*  *********************************************************************
+    *  Some general notes:
+    *
+    *  Register addresses are grouped by function and follow the order
+    *  of the User Manual.
+    *
+    *  For the most part, when there is more than one peripheral
+    *  of the same type on the SOC, the constants below will be
+    *  offsets from the base of each peripheral.  For example,
+    *  the MAC registers are described as offsets from the first
+    *  MAC register, and there will be a MAC_REGISTER() macro
+    *  to calculate the base address of a given MAC.
+    *
+    *  The information in this file is based on the BCM1X55/BCM1X80
+    *  User Manual, Document 1X55_1X80-UM100-R, 22/12/03.
+    *
+    *  This file is basically a "what's new" header file.  Since the
+    *  BCM1250 and the new BCM1480 (and derivatives) share many common
+    *  features, this file contains only what's new or changed from
+    *  the 1250.  (above, you can see that we include the 1250 symbols
+    *  to get the base functionality).
+    *
+    *  In software, be sure to use the correct symbols, particularly
+    *  for blocks that are different between the two chip families.
+    *  All BCM1480-specific symbols have _BCM1480_ in their names,
+    *  and all BCM1250-specific and "base" functions that are common in
+    *  both chips have no special names (this is for compatibility with
+    *  older include files).  Therefore, if you're working with the
+    *  SCD, which is very different on each chip, A_SCD_xxx implies
+    *  the BCM1250 version and A_BCM1480_SCD_xxx implies the BCM1480
+    *  version.
+    ********************************************************************* */
+
+
+/*  *********************************************************************
+    * Memory Controller Registers (Section 6)
+    ********************************************************************* */
+
+#define A_BCM1480_MC_BASE_0		    0x0010050000
+#define A_BCM1480_MC_BASE_1		    0x0010051000
+#define A_BCM1480_MC_BASE_2		    0x0010052000
+#define A_BCM1480_MC_BASE_3		    0x0010053000
+#define BCM1480_MC_REGISTER_SPACING	    0x1000
+
+#define A_BCM1480_MC_BASE(ctlid)	    (A_BCM1480_MC_BASE_0+(ctlid)*BCM1480_MC_REGISTER_SPACING)
+#define A_BCM1480_MC_REGISTER(ctlid, reg)    (A_BCM1480_MC_BASE(ctlid)+(reg))
+
+#define R_BCM1480_MC_CONFIG		    0x0000000100
+#define R_BCM1480_MC_CS_START		    0x0000000120
+#define R_BCM1480_MC_CS_END		    0x0000000140
+#define S_BCM1480_MC_CS_STARTEND	    24
+
+#define R_BCM1480_MC_CS01_ROW0		    0x0000000180
+#define R_BCM1480_MC_CS01_ROW1		    0x00000001A0
+#define R_BCM1480_MC_CS23_ROW0		    0x0000000200
+#define R_BCM1480_MC_CS23_ROW1		    0x0000000220
+#define R_BCM1480_MC_CS01_COL0		    0x0000000280
+#define R_BCM1480_MC_CS01_COL1		    0x00000002A0
+#define R_BCM1480_MC_CS23_COL0		    0x0000000300
+#define R_BCM1480_MC_CS23_COL1		    0x0000000320
+
+#define R_BCM1480_MC_CSX_BASE		    0x0000000180
+#define R_BCM1480_MC_CSX_ROW0		    0x0000000000   /* relative to CSX_BASE */
+#define R_BCM1480_MC_CSX_ROW1		    0x0000000020   /* relative to CSX_BASE */
+#define R_BCM1480_MC_CSX_COL0		    0x0000000100   /* relative to CSX_BASE */
+#define R_BCM1480_MC_CSX_COL1		    0x0000000120   /* relative to CSX_BASE */
+#define BCM1480_MC_CSX_SPACING		    0x0000000080   /* CS23 relative to CS01 */
+
+#define R_BCM1480_MC_CS01_BA		    0x0000000380
+#define R_BCM1480_MC_CS23_BA		    0x00000003A0
+#define R_BCM1480_MC_DRAMCMD		    0x0000000400
+#define R_BCM1480_MC_DRAMMODE		    0x0000000420
+#define R_BCM1480_MC_CLOCK_CFG		    0x0000000440
+#define R_BCM1480_MC_MCLK_CFG		    R_BCM1480_MC_CLOCK_CFG
+#define R_BCM1480_MC_TEST_DATA		    0x0000000480
+#define R_BCM1480_MC_TEST_ECC		    0x00000004A0
+#define R_BCM1480_MC_TIMING1		    0x00000004C0
+#define R_BCM1480_MC_TIMING2		    0x00000004E0
+#define R_BCM1480_MC_DLL_CFG		    0x0000000500
+#define R_BCM1480_MC_DRIVE_CFG		    0x0000000520
+
+#if SIBYTE_HDR_FEATURE(1480, PASS2)
+#define R_BCM1480_MC_ODT		    0x0000000460
+#define R_BCM1480_MC_ECC_STATUS		    0x0000000540
+#endif
+
+/* Global registers (single instance) */
+#define A_BCM1480_MC_GLB_CONFIG		    0x0010054100
+#define A_BCM1480_MC_GLB_INTLV		    0x0010054120
+#define A_BCM1480_MC_GLB_ECC_STATUS	    0x0010054140
+#define A_BCM1480_MC_GLB_ECC_ADDR	    0x0010054160
+#define A_BCM1480_MC_GLB_ECC_CORRECT	    0x0010054180
+#define A_BCM1480_MC_GLB_PERF_CNT_CONTROL   0x00100541A0
+
+/*  *********************************************************************
+    * L2 Cache Control Registers (Section 5)
+    ********************************************************************* */
+
+#define A_BCM1480_L2_BASE		    0x0010040000
+
+#define A_BCM1480_L2_READ_TAG		    0x0010040018
+#define A_BCM1480_L2_ECC_TAG		    0x0010040038
+#define A_BCM1480_L2_MISC0_VALUE	    0x0010040058
+#define A_BCM1480_L2_MISC1_VALUE	    0x0010040078
+#define A_BCM1480_L2_MISC2_VALUE	    0x0010040098
+#define A_BCM1480_L2_MISC_CONFIG	    0x0010040040	/* x040 */
+#define A_BCM1480_L2_CACHE_DISABLE	    0x0010040060	/* x060 */
+#define A_BCM1480_L2_MAKECACHEDISABLE(x)    (A_BCM1480_L2_CACHE_DISABLE | (((x)&0xF) << 12))
+#define A_BCM1480_L2_WAY_ENABLE_3_0	    0x0010040080	/* x080 */
+#define A_BCM1480_L2_WAY_ENABLE_7_4	    0x00100400A0	/* x0A0 */
+#define A_BCM1480_L2_MAKE_WAY_ENABLE_LO(x)  (A_BCM1480_L2_WAY_ENABLE_3_0 | (((x)&0xF) << 12))
+#define A_BCM1480_L2_MAKE_WAY_ENABLE_HI(x)  (A_BCM1480_L2_WAY_ENABLE_7_4 | (((x)&0xF) << 12))
+#define A_BCM1480_L2_MAKE_WAY_DISABLE_LO(x)  (A_BCM1480_L2_WAY_ENABLE_3_0 | (((~x)&0xF) << 12))
+#define A_BCM1480_L2_MAKE_WAY_DISABLE_HI(x)  (A_BCM1480_L2_WAY_ENABLE_7_4 | (((~x)&0xF) << 12))
+#define A_BCM1480_L2_WAY_LOCAL_3_0	    0x0010040100	/* x100 */
+#define A_BCM1480_L2_WAY_LOCAL_7_4	    0x0010040120	/* x120 */
+#define A_BCM1480_L2_WAY_REMOTE_3_0	    0x0010040140	/* x140 */
+#define A_BCM1480_L2_WAY_REMOTE_7_4	    0x0010040160	/* x160 */
+#define A_BCM1480_L2_WAY_AGENT_3_0	    0x00100400C0	/* xxC0 */
+#define A_BCM1480_L2_WAY_AGENT_7_4	    0x00100400E0	/* xxE0 */
+#define A_BCM1480_L2_WAY_ENABLE(A, banks)   (A | (((~(banks))&0x0F) << 8))
+#define A_BCM1480_L2_BANK_BASE		    0x00D0300000
+#define A_BCM1480_L2_BANK_ADDRESS(b)	    (A_BCM1480_L2_BANK_BASE | (((b)&0x7)<<17))
+#define A_BCM1480_L2_MGMT_TAG_BASE	    0x00D0000000
+
+
+/*  *********************************************************************
+    * PCI-X Interface Registers (Section 7)
+    ********************************************************************* */
+
+#define A_BCM1480_PCI_BASE		    0x0010061400
+
+#define A_BCM1480_PCI_RESET		    0x0010061400
+#define A_BCM1480_PCI_DLL		    0x0010061500
+
+#define A_BCM1480_PCI_TYPE00_HEADER	    0x002E000000
+
+/*  *********************************************************************
+    * Ethernet MAC Registers (Section 11) and DMA Registers (Section 10.6)
+    ********************************************************************* */
+
+/* No register changes with Rev.C BCM1250, but one additional MAC */
+
+#define A_BCM1480_MAC_BASE_2	    0x0010066000
+
+#ifndef A_MAC_BASE_2
+#define A_MAC_BASE_2		    A_BCM1480_MAC_BASE_2
+#endif
+
+#define A_BCM1480_MAC_BASE_3	    0x0010067000
+#define A_MAC_BASE_3		    A_BCM1480_MAC_BASE_3
+
+#define R_BCM1480_MAC_DMA_OODPKTLOST	    0x00000038
+
+#ifndef R_MAC_DMA_OODPKTLOST
+#define R_MAC_DMA_OODPKTLOST	    R_BCM1480_MAC_DMA_OODPKTLOST
+#endif
+
+
+/*  *********************************************************************
+    * DUART Registers (Section 14)
+    ********************************************************************* */
+
+/* No significant differences from BCM1250, two DUARTs */
+
+/*  Conventions, per user manual:
+ *     DUART	generic, channels A,B,C,D
+ *     DUART0	implementing channels A,B
+ *     DUART1	inplementing channels C,D
+ */
+
+#define BCM1480_DUART_NUM_PORTS		  4
+
+#define A_BCM1480_DUART0		    0x0010060000
+#define A_BCM1480_DUART1		    0x0010060400
+#define A_BCM1480_DUART(chan)		    ((((chan)&2) == 0)? A_BCM1480_DUART0 : A_BCM1480_DUART1)
+
+#define BCM1480_DUART_CHANREG_SPACING	    0x100
+#define A_BCM1480_DUART_CHANREG(chan, reg)				\
+	(A_BCM1480_DUART(chan) +					\
+	 BCM1480_DUART_CHANREG_SPACING * (((chan) & 1) + 1) + (reg))
+#define A_BCM1480_DUART_CTRLREG(chan, reg)				\
+	(A_BCM1480_DUART(chan) +					\
+	 BCM1480_DUART_CHANREG_SPACING * 3 + (reg))
+
+#define DUART_IMRISR_SPACING	    0x20
+#define DUART_INCHNG_SPACING	    0x10
+
+#define R_BCM1480_DUART_IMRREG(chan)					\
+	(R_DUART_IMR_A + ((chan) & 1) * DUART_IMRISR_SPACING)
+#define R_BCM1480_DUART_ISRREG(chan)					\
+	(R_DUART_ISR_A + ((chan) & 1) * DUART_IMRISR_SPACING)
+#define R_BCM1480_DUART_INCHREG(chan)					\
+	(R_DUART_IN_CHNG_A + ((chan) & 1) * DUART_INCHNG_SPACING)
+
+#define A_BCM1480_DUART_IMRREG(chan)					\
+	(A_BCM1480_DUART_CTRLREG((chan), R_BCM1480_DUART_IMRREG(chan)))
+#define A_BCM1480_DUART_ISRREG(chan)					\
+	(A_BCM1480_DUART_CTRLREG((chan), R_BCM1480_DUART_ISRREG(chan)))
+
+#define A_BCM1480_DUART_IN_PORT(chan)					\
+	(A_BCM1480_DUART_CTRLREG((chan), R_DUART_IN_PORT))
+
+/*
+ * These constants are the absolute addresses.
+ */
+
+#define A_BCM1480_DUART_MODE_REG_1_C	    0x0010060400
+#define A_BCM1480_DUART_MODE_REG_2_C	    0x0010060410
+#define A_BCM1480_DUART_STATUS_C	    0x0010060420
+#define A_BCM1480_DUART_CLK_SEL_C	    0x0010060430
+#define A_BCM1480_DUART_FULL_CTL_C	    0x0010060440
+#define A_BCM1480_DUART_CMD_C		    0x0010060450
+#define A_BCM1480_DUART_RX_HOLD_C	    0x0010060460
+#define A_BCM1480_DUART_TX_HOLD_C	    0x0010060470
+#define A_BCM1480_DUART_OPCR_C		    0x0010060480
+#define A_BCM1480_DUART_AUX_CTRL_C	    0x0010060490
+
+#define A_BCM1480_DUART_MODE_REG_1_D	    0x0010060500
+#define A_BCM1480_DUART_MODE_REG_2_D	    0x0010060510
+#define A_BCM1480_DUART_STATUS_D	    0x0010060520
+#define A_BCM1480_DUART_CLK_SEL_D	    0x0010060530
+#define A_BCM1480_DUART_FULL_CTL_D	    0x0010060540
+#define A_BCM1480_DUART_CMD_D		    0x0010060550
+#define A_BCM1480_DUART_RX_HOLD_D	    0x0010060560
+#define A_BCM1480_DUART_TX_HOLD_D	    0x0010060570
+#define A_BCM1480_DUART_OPCR_D		    0x0010060580
+#define A_BCM1480_DUART_AUX_CTRL_D	    0x0010060590
+
+#define A_BCM1480_DUART_INPORT_CHNG_CD	    0x0010060600
+#define A_BCM1480_DUART_AUX_CTRL_CD	    0x0010060610
+#define A_BCM1480_DUART_ISR_C		    0x0010060620
+#define A_BCM1480_DUART_IMR_C		    0x0010060630
+#define A_BCM1480_DUART_ISR_D		    0x0010060640
+#define A_BCM1480_DUART_IMR_D		    0x0010060650
+#define A_BCM1480_DUART_OUT_PORT_CD	    0x0010060660
+#define A_BCM1480_DUART_OPCR_CD		    0x0010060670
+#define A_BCM1480_DUART_IN_PORT_CD	    0x0010060680
+#define A_BCM1480_DUART_ISR_CD		    0x0010060690
+#define A_BCM1480_DUART_IMR_CD		    0x00100606A0
+#define A_BCM1480_DUART_SET_OPR_CD	    0x00100606B0
+#define A_BCM1480_DUART_CLEAR_OPR_CD	    0x00100606C0
+#define A_BCM1480_DUART_INPORT_CHNG_C	    0x00100606D0
+#define A_BCM1480_DUART_INPORT_CHNG_D	    0x00100606E0
+
+
+/*  *********************************************************************
+    * Generic Bus Registers (Section 15) and PCMCIA Registers (Section 16)
+    ********************************************************************* */
+
+#define A_BCM1480_IO_PCMCIA_CFG_B	0x0010061A58
+#define A_BCM1480_IO_PCMCIA_STATUS_B	0x0010061A68
+
+/*  *********************************************************************
+    * GPIO Registers (Section 17)
+    ********************************************************************* */
+
+/* One additional GPIO register, placed _before_ the BCM1250's GPIO block base */
+
+#define A_BCM1480_GPIO_INT_ADD_TYPE	    0x0010061A78
+#define R_BCM1480_GPIO_INT_ADD_TYPE	    (-8)
+
+#define A_GPIO_INT_ADD_TYPE	A_BCM1480_GPIO_INT_ADD_TYPE
+#define R_GPIO_INT_ADD_TYPE	R_BCM1480_GPIO_INT_ADD_TYPE
+
+/*  *********************************************************************
+    * SMBus Registers (Section 18)
+    ********************************************************************* */
+
+/* No changes from BCM1250 */
+
+/*  *********************************************************************
+    * Timer Registers (Sections 4.6)
+    ********************************************************************* */
+
+/* BCM1480 has two additional watchdogs */
+
+/* Watchdog timers */
+
+#define A_BCM1480_SCD_WDOG_2		    0x0010022050
+#define A_BCM1480_SCD_WDOG_3		    0x0010022150
+
+#define BCM1480_SCD_NUM_WDOGS		    4
+
+#define A_BCM1480_SCD_WDOG_BASE(w)	 (A_BCM1480_SCD_WDOG_0+((w)&2)*0x1000 + ((w)&1)*0x100)
+#define A_BCM1480_SCD_WDOG_REGISTER(w, r) (A_BCM1480_SCD_WDOG_BASE(w) + (r))
+
+#define A_BCM1480_SCD_WDOG_INIT_2	0x0010022050
+#define A_BCM1480_SCD_WDOG_CNT_2	0x0010022058
+#define A_BCM1480_SCD_WDOG_CFG_2	0x0010022060
+
+#define A_BCM1480_SCD_WDOG_INIT_3	0x0010022150
+#define A_BCM1480_SCD_WDOG_CNT_3	0x0010022158
+#define A_BCM1480_SCD_WDOG_CFG_3	0x0010022160
+
+/* BCM1480 has two additional compare registers */
+
+#define A_BCM1480_SCD_ZBBUS_CYCLE_COUNT		A_SCD_ZBBUS_CYCLE_COUNT
+#define A_BCM1480_SCD_ZBBUS_CYCLE_CP_BASE	0x0010020C00
+#define A_BCM1480_SCD_ZBBUS_CYCLE_CP0		A_SCD_ZBBUS_CYCLE_CP0
+#define A_BCM1480_SCD_ZBBUS_CYCLE_CP1		A_SCD_ZBBUS_CYCLE_CP1
+#define A_BCM1480_SCD_ZBBUS_CYCLE_CP2		0x0010020C10
+#define A_BCM1480_SCD_ZBBUS_CYCLE_CP3		0x0010020C18
+
+/*  *********************************************************************
+    * System Control Registers (Section 4.2)
+    ********************************************************************* */
+
+/* Scratch register in different place */
+
+#define A_BCM1480_SCD_SCRATCH		0x100200A0
+
+/*  *********************************************************************
+    * System Address Trap Registers (Section 4.9)
+    ********************************************************************* */
+
+/* No changes from BCM1250 */
+
+/*  *********************************************************************
+    * System Interrupt Mapper Registers (Sections 4.3-4.5)
+    ********************************************************************* */
+
+#define A_BCM1480_IMR_CPU0_BASE		    0x0010020000
+#define A_BCM1480_IMR_CPU1_BASE		    0x0010022000
+#define A_BCM1480_IMR_CPU2_BASE		    0x0010024000
+#define A_BCM1480_IMR_CPU3_BASE		    0x0010026000
+#define BCM1480_IMR_REGISTER_SPACING	    0x2000
+#define BCM1480_IMR_REGISTER_SPACING_SHIFT  13
+
+#define A_BCM1480_IMR_MAPPER(cpu)	(A_BCM1480_IMR_CPU0_BASE+(cpu)*BCM1480_IMR_REGISTER_SPACING)
+#define A_BCM1480_IMR_REGISTER(cpu, reg) (A_BCM1480_IMR_MAPPER(cpu)+(reg))
+
+/* Most IMR registers are 128 bits, implemented as non-contiguous
+   64-bit registers high (_H) and low (_L) */
+#define BCM1480_IMR_HL_SPACING			0x1000
+
+#define R_BCM1480_IMR_INTERRUPT_DIAG_H		0x0010
+#define R_BCM1480_IMR_LDT_INTERRUPT_H		0x0018
+#define R_BCM1480_IMR_LDT_INTERRUPT_CLR_H	0x0020
+#define R_BCM1480_IMR_INTERRUPT_MASK_H		0x0028
+#define R_BCM1480_IMR_INTERRUPT_TRACE_H		0x0038
+#define R_BCM1480_IMR_INTERRUPT_SOURCE_STATUS_H 0x0040
+#define R_BCM1480_IMR_LDT_INTERRUPT_SET		0x0048
+#define R_BCM1480_IMR_MAILBOX_0_CPU		0x00C0
+#define R_BCM1480_IMR_MAILBOX_0_SET_CPU		0x00C8
+#define R_BCM1480_IMR_MAILBOX_0_CLR_CPU		0x00D0
+#define R_BCM1480_IMR_MAILBOX_1_CPU		0x00E0
+#define R_BCM1480_IMR_MAILBOX_1_SET_CPU		0x00E8
+#define R_BCM1480_IMR_MAILBOX_1_CLR_CPU		0x00F0
+#define R_BCM1480_IMR_INTERRUPT_STATUS_BASE_H	0x0100
+#define BCM1480_IMR_INTERRUPT_STATUS_COUNT	8
+#define R_BCM1480_IMR_INTERRUPT_MAP_BASE_H	0x0200
+#define BCM1480_IMR_INTERRUPT_MAP_COUNT		64
+
+#define R_BCM1480_IMR_INTERRUPT_DIAG_L		0x1010
+#define R_BCM1480_IMR_LDT_INTERRUPT_L		0x1018
+#define R_BCM1480_IMR_LDT_INTERRUPT_CLR_L	0x1020
+#define R_BCM1480_IMR_INTERRUPT_MASK_L		0x1028
+#define R_BCM1480_IMR_INTERRUPT_TRACE_L		0x1038
+#define R_BCM1480_IMR_INTERRUPT_SOURCE_STATUS_L 0x1040
+#define R_BCM1480_IMR_INTERRUPT_STATUS_BASE_L	0x1100
+#define R_BCM1480_IMR_INTERRUPT_MAP_BASE_L	0x1200
+
+#define A_BCM1480_IMR_ALIAS_MAILBOX_CPU0_BASE	0x0010028000
+#define A_BCM1480_IMR_ALIAS_MAILBOX_CPU1_BASE	0x0010028100
+#define A_BCM1480_IMR_ALIAS_MAILBOX_CPU2_BASE	0x0010028200
+#define A_BCM1480_IMR_ALIAS_MAILBOX_CPU3_BASE	0x0010028300
+#define BCM1480_IMR_ALIAS_MAILBOX_SPACING	0100
+
+#define A_BCM1480_IMR_ALIAS_MAILBOX(cpu)     (A_BCM1480_IMR_ALIAS_MAILBOX_CPU0_BASE + \
+					(cpu)*BCM1480_IMR_ALIAS_MAILBOX_SPACING)
+#define A_BCM1480_IMR_ALIAS_MAILBOX_REGISTER(cpu, reg) (A_BCM1480_IMR_ALIAS_MAILBOX(cpu)+(reg))
+
+#define R_BCM1480_IMR_ALIAS_MAILBOX_0		0x0000
+#define R_BCM1480_IMR_ALIAS_MAILBOX_0_SET	0x0008
+
+/*
+ * these macros work together to build the address of a mailbox
+ * register, e.g., A_BCM1480_MAILBOX_REGISTER(0,R_BCM1480_IMR_MAILBOX_SET,2)
+ * for mbox_0_set_cpu2 returns 0x00100240C8
+ */
+#define R_BCM1480_IMR_MAILBOX_CPU	  0x00
+#define R_BCM1480_IMR_MAILBOX_SET	  0x08
+#define R_BCM1480_IMR_MAILBOX_CLR	  0x10
+#define R_BCM1480_IMR_MAILBOX_NUM_SPACING 0x20
+#define A_BCM1480_MAILBOX_REGISTER(num, reg, cpu) \
+    (A_BCM1480_IMR_CPU0_BASE + \
+     (num * R_BCM1480_IMR_MAILBOX_NUM_SPACING) + \
+     (cpu * BCM1480_IMR_REGISTER_SPACING) + \
+     (R_BCM1480_IMR_MAILBOX_0_CPU + reg))
+
+/*  *********************************************************************
+    * System Performance Counter Registers (Section 4.7)
+    ********************************************************************* */
+
+/* BCM1480 has four more performance counter registers, and two control
+   registers. */
+
+#define A_BCM1480_SCD_PERF_CNT_BASE	    0x00100204C0
+
+#define A_BCM1480_SCD_PERF_CNT_CFG0	    0x00100204C0
+#define A_BCM1480_SCD_PERF_CNT_CFG_0	    A_BCM1480_SCD_PERF_CNT_CFG0
+#define A_BCM1480_SCD_PERF_CNT_CFG1	    0x00100204C8
+#define A_BCM1480_SCD_PERF_CNT_CFG_1	    A_BCM1480_SCD_PERF_CNT_CFG1
+
+#define A_BCM1480_SCD_PERF_CNT_0	    A_SCD_PERF_CNT_0
+#define A_BCM1480_SCD_PERF_CNT_1	    A_SCD_PERF_CNT_1
+#define A_BCM1480_SCD_PERF_CNT_2	    A_SCD_PERF_CNT_2
+#define A_BCM1480_SCD_PERF_CNT_3	    A_SCD_PERF_CNT_3
+
+#define A_BCM1480_SCD_PERF_CNT_4	    0x00100204F0
+#define A_BCM1480_SCD_PERF_CNT_5	    0x00100204F8
+#define A_BCM1480_SCD_PERF_CNT_6	    0x0010020500
+#define A_BCM1480_SCD_PERF_CNT_7	    0x0010020508
+
+#define BCM1480_SCD_NUM_PERF_CNT 8
+#define BCM1480_SCD_PERF_CNT_SPACING 8
+#define A_BCM1480_SCD_PERF_CNT(n) (A_SCD_PERF_CNT_0+(n*BCM1480_SCD_PERF_CNT_SPACING))
+
+/*  *********************************************************************
+    * System Bus Watcher Registers (Section 4.8)
+    ********************************************************************* */
+
+
+/* Same as 1250 except BUS_ERR_STATUS_DEBUG is in a different place. */
+
+#define A_BCM1480_BUS_ERR_STATUS_DEBUG	    0x00100208D8
+
+/*  *********************************************************************
+    * System Debug Controller Registers (Section 19)
+    ********************************************************************* */
+
+/* Same as 1250 */
+
+/*  *********************************************************************
+    * System Trace Unit Registers (Sections 4.10)
+    ********************************************************************* */
+
+/* Same as 1250 */
+
+/*  *********************************************************************
+    * Data Mover DMA Registers (Section 10.7)
+    ********************************************************************* */
+
+/* Same as 1250 */
+
+
+/*  *********************************************************************
+    * HyperTransport Interface Registers (Section 8)
+    ********************************************************************* */
+
+#define BCM1480_HT_NUM_PORTS		   3
+#define BCM1480_HT_PORT_SPACING		   0x800
+#define A_BCM1480_HT_PORT_HEADER(x)	   (A_BCM1480_HT_PORT0_HEADER + ((x)*BCM1480_HT_PORT_SPACING))
+
+#define A_BCM1480_HT_PORT0_HEADER	   0x00FE000000
+#define A_BCM1480_HT_PORT1_HEADER	   0x00FE000800
+#define A_BCM1480_HT_PORT2_HEADER	   0x00FE001000
+#define A_BCM1480_HT_TYPE00_HEADER	   0x00FE002000
+
+
+/*  *********************************************************************
+    * Node Controller Registers (Section 9)
+    ********************************************************************* */
+
+#define A_BCM1480_NC_BASE		    0x00DFBD0000
+
+#define A_BCM1480_NC_RLD_FIELD		    0x00DFBD0000
+#define A_BCM1480_NC_RLD_TRIGGER	    0x00DFBD0020
+#define A_BCM1480_NC_RLD_BAD_ERROR	    0x00DFBD0040
+#define A_BCM1480_NC_RLD_COR_ERROR	    0x00DFBD0060
+#define A_BCM1480_NC_RLD_ECC_STATUS	    0x00DFBD0080
+#define A_BCM1480_NC_RLD_WAY_ENABLE	    0x00DFBD00A0
+#define A_BCM1480_NC_RLD_RANDOM_LFSR	    0x00DFBD00C0
+
+#define A_BCM1480_NC_INTERRUPT_STATUS	    0x00DFBD00E0
+#define A_BCM1480_NC_INTERRUPT_ENABLE	    0x00DFBD0100
+#define A_BCM1480_NC_TIMEOUT_COUNTER	    0x00DFBD0120
+#define A_BCM1480_NC_TIMEOUT_COUNTER_SEL    0x00DFBD0140
+
+#define A_BCM1480_NC_CREDIT_STATUS_REG0	    0x00DFBD0200
+#define A_BCM1480_NC_CREDIT_STATUS_REG1	    0x00DFBD0220
+#define A_BCM1480_NC_CREDIT_STATUS_REG2	    0x00DFBD0240
+#define A_BCM1480_NC_CREDIT_STATUS_REG3	    0x00DFBD0260
+#define A_BCM1480_NC_CREDIT_STATUS_REG4	    0x00DFBD0280
+#define A_BCM1480_NC_CREDIT_STATUS_REG5	    0x00DFBD02A0
+#define A_BCM1480_NC_CREDIT_STATUS_REG6	    0x00DFBD02C0
+#define A_BCM1480_NC_CREDIT_STATUS_REG7	    0x00DFBD02E0
+#define A_BCM1480_NC_CREDIT_STATUS_REG8	    0x00DFBD0300
+#define A_BCM1480_NC_CREDIT_STATUS_REG9	    0x00DFBD0320
+#define A_BCM1480_NC_CREDIT_STATUS_REG10    0x00DFBE0000
+#define A_BCM1480_NC_CREDIT_STATUS_REG11    0x00DFBE0020
+#define A_BCM1480_NC_CREDIT_STATUS_REG12    0x00DFBE0040
+
+#define A_BCM1480_NC_SR_TIMEOUT_COUNTER	    0x00DFBE0060
+#define A_BCM1480_NC_SR_TIMEOUT_COUNTER_SEL 0x00DFBE0080
+
+
+/*  *********************************************************************
+    * H&R Block Configuration Registers (Section 12.4)
+    ********************************************************************* */
+
+#define A_BCM1480_HR_BASE_0		    0x00DF820000
+#define A_BCM1480_HR_BASE_1		    0x00DF8A0000
+#define A_BCM1480_HR_BASE_2		    0x00DF920000
+#define BCM1480_HR_REGISTER_SPACING	    0x80000
+
+#define A_BCM1480_HR_BASE(idx)		    (A_BCM1480_HR_BASE_0 + ((idx)*BCM1480_HR_REGISTER_SPACING))
+#define A_BCM1480_HR_REGISTER(idx, reg)	     (A_BCM1480_HR_BASE(idx) + (reg))
+
+#define R_BCM1480_HR_CFG		    0x0000000000
+
+#define R_BCM1480_HR_MAPPING		    0x0000010010
+
+#define BCM1480_HR_RULE_SPACING		    0x0000000010
+#define BCM1480_HR_NUM_RULES		    16
+#define BCM1480_HR_OP_OFFSET		    0x0000000100
+#define BCM1480_HR_TYPE_OFFSET		    0x0000000108
+#define R_BCM1480_HR_RULE_OP(idx)	    (BCM1480_HR_OP_OFFSET + ((idx)*BCM1480_HR_RULE_SPACING))
+#define R_BCM1480_HR_RULE_TYPE(idx)	    (BCM1480_HR_TYPE_OFFSET + ((idx)*BCM1480_HR_RULE_SPACING))
+
+#define BCM1480_HR_LEAF_SPACING		    0x0000000010
+#define BCM1480_HR_NUM_LEAVES		    10
+#define BCM1480_HR_LEAF_OFFSET		    0x0000000300
+#define R_BCM1480_HR_HA_LEAF0(idx)	    (BCM1480_HR_LEAF_OFFSET + ((idx)*BCM1480_HR_LEAF_SPACING))
+
+#define R_BCM1480_HR_EX_LEAF0		    0x00000003A0
+
+#define BCM1480_HR_PATH_SPACING		    0x0000000010
+#define BCM1480_HR_NUM_PATHS		    16
+#define BCM1480_HR_PATH_OFFSET		    0x0000000600
+#define R_BCM1480_HR_PATH(idx)		    (BCM1480_HR_PATH_OFFSET + ((idx)*BCM1480_HR_PATH_SPACING))
+
+#define R_BCM1480_HR_PATH_DEFAULT	    0x0000000700
+
+#define BCM1480_HR_ROUTE_SPACING	    8
+#define BCM1480_HR_NUM_ROUTES		    512
+#define BCM1480_HR_ROUTE_OFFSET		    0x0000001000
+#define R_BCM1480_HR_RT_WORD(idx)	    (BCM1480_HR_ROUTE_OFFSET + ((idx)*BCM1480_HR_ROUTE_SPACING))
+
+
+/* checked to here - ehs */
+/*  *********************************************************************
+    * Packet Manager DMA Registers (Section 12.5)
+    ********************************************************************* */
+
+#define A_BCM1480_PM_BASE		    0x0010056000
+
+#define A_BCM1480_PMI_LCL_0		    0x0010058000
+#define A_BCM1480_PMO_LCL_0		    0x001005C000
+#define A_BCM1480_PMI_OFFSET_0		    (A_BCM1480_PMI_LCL_0 - A_BCM1480_PM_BASE)
+#define A_BCM1480_PMO_OFFSET_0		    (A_BCM1480_PMO_LCL_0 - A_BCM1480_PM_BASE)
+
+#define BCM1480_PM_LCL_REGISTER_SPACING	    0x100
+#define BCM1480_PM_NUM_CHANNELS		    32
+
+#define A_BCM1480_PMI_LCL_BASE(idx)		(A_BCM1480_PMI_LCL_0 + ((idx)*BCM1480_PM_LCL_REGISTER_SPACING))
+#define A_BCM1480_PMI_LCL_REGISTER(idx, reg)	 (A_BCM1480_PMI_LCL_BASE(idx) + (reg))
+#define A_BCM1480_PMO_LCL_BASE(idx)		(A_BCM1480_PMO_LCL_0 + ((idx)*BCM1480_PM_LCL_REGISTER_SPACING))
+#define A_BCM1480_PMO_LCL_REGISTER(idx, reg)	 (A_BCM1480_PMO_LCL_BASE(idx) + (reg))
+
+#define BCM1480_PM_INT_PACKING		    8
+#define BCM1480_PM_INT_FUNCTION_SPACING	    0x40
+#define BCM1480_PM_INT_NUM_FUNCTIONS	    3
+
+/*
+ * DMA channel registers relative to A_BCM1480_PMI_LCL_BASE(n) and A_BCM1480_PMO_LCL_BASE(n)
+ */
+
+#define R_BCM1480_PM_BASE_SIZE		    0x0000000000
+#define R_BCM1480_PM_CNT		    0x0000000008
+#define R_BCM1480_PM_PFCNT		    0x0000000010
+#define R_BCM1480_PM_LAST		    0x0000000018
+#define R_BCM1480_PM_PFINDX		    0x0000000020
+#define R_BCM1480_PM_INT_WMK		    0x0000000028
+#define R_BCM1480_PM_CONFIG0		    0x0000000030
+#define R_BCM1480_PM_LOCALDEBUG		    0x0000000078
+#define R_BCM1480_PM_CACHEABILITY	    0x0000000080   /* PMI only */
+#define R_BCM1480_PM_INT_CNFG		    0x0000000088
+#define R_BCM1480_PM_DESC_MERGE_TIMER	    0x0000000090
+#define R_BCM1480_PM_LOCALDEBUG_PIB	    0x00000000F8   /* PMI only */
+#define R_BCM1480_PM_LOCALDEBUG_POB	    0x00000000F8   /* PMO only */
+
+/*
+ * Global Registers (Not Channelized)
+ */
+
+#define A_BCM1480_PMI_GLB_0		    0x0010056000
+#define A_BCM1480_PMO_GLB_0		    0x0010057000
+
+/*
+ * PM to TX Mapping Register relative to A_BCM1480_PMI_GLB_0 and A_BCM1480_PMO_GLB_0
+ */
+
+#define R_BCM1480_PM_PMO_MAPPING	    0x00000008C8   /* PMO only */
+
+#define A_BCM1480_PM_PMO_MAPPING	(A_BCM1480_PMO_GLB_0 + R_BCM1480_PM_PMO_MAPPING)
+
+/*
+ * Interrupt mapping registers
+ */
+
+
+#define A_BCM1480_PMI_INT_0		    0x0010056800
+#define A_BCM1480_PMI_INT(q)		    (A_BCM1480_PMI_INT_0 + ((q>>8)<<8))
+#define A_BCM1480_PMI_INT_OFFSET_0	    (A_BCM1480_PMI_INT_0 - A_BCM1480_PM_BASE)
+#define A_BCM1480_PMO_INT_0		    0x0010057800
+#define A_BCM1480_PMO_INT(q)		    (A_BCM1480_PMO_INT_0 + ((q>>8)<<8))
+#define A_BCM1480_PMO_INT_OFFSET_0	    (A_BCM1480_PMO_INT_0 - A_BCM1480_PM_BASE)
+
+/*
+ * Interrupt registers relative to A_BCM1480_PMI_INT_0 and A_BCM1480_PMO_INT_0
+ */
+
+#define R_BCM1480_PM_INT_ST		    0x0000000000
+#define R_BCM1480_PM_INT_MSK		    0x0000000040
+#define R_BCM1480_PM_INT_CLR		    0x0000000080
+#define R_BCM1480_PM_MRGD_INT		    0x00000000C0
+
+/*
+ * Debug registers (global)
+ */
+
+#define A_BCM1480_PM_GLOBALDEBUGMODE_PMI    0x0010056000
+#define A_BCM1480_PM_GLOBALDEBUG_PID	    0x00100567F8
+#define A_BCM1480_PM_GLOBALDEBUG_PIB	    0x0010056FF8
+#define A_BCM1480_PM_GLOBALDEBUGMODE_PMO    0x0010057000
+#define A_BCM1480_PM_GLOBALDEBUG_POD	    0x00100577F8
+#define A_BCM1480_PM_GLOBALDEBUG_POB	    0x0010057FF8
+
+/*  *********************************************************************
+    *  Switch performance counters
+    ********************************************************************* */
+
+#define A_BCM1480_SWPERF_CFG	0xdfb91800
+#define A_BCM1480_SWPERF_CNT0	0xdfb91880
+#define A_BCM1480_SWPERF_CNT1	0xdfb91888
+#define A_BCM1480_SWPERF_CNT2	0xdfb91890
+#define A_BCM1480_SWPERF_CNT3	0xdfb91898
+
+
+/*  *********************************************************************
+    *  Switch Trace Unit
+    ********************************************************************* */
+
+#define A_BCM1480_SWTRC_MATCH_CONTROL_0		0xDFB91000
+#define A_BCM1480_SWTRC_MATCH_DATA_VALUE_0	0xDFB91100
+#define A_BCM1480_SWTRC_MATCH_DATA_MASK_0	0xDFB91108
+#define A_BCM1480_SWTRC_MATCH_TAG_VALUE_0	0xDFB91200
+#define A_BCM1480_SWTRC_MATCH_TAG_MAKS_0	0xDFB91208
+#define A_BCM1480_SWTRC_EVENT_0			0xDFB91300
+#define A_BCM1480_SWTRC_SEQUENCE_0		0xDFB91400
+
+#define A_BCM1480_SWTRC_CFG			0xDFB91500
+#define A_BCM1480_SWTRC_READ			0xDFB91508
+
+#define A_BCM1480_SWDEBUG_SCHEDSTOP		0xDFB92000
+
+#define A_BCM1480_SWTRC_MATCH_CONTROL(x) (A_BCM1480_SWTRC_MATCH_CONTROL_0 + ((x)*8))
+#define A_BCM1480_SWTRC_EVENT(x) (A_BCM1480_SWTRC_EVENT_0 + ((x)*8))
+#define A_BCM1480_SWTRC_SEQUENCE(x) (A_BCM1480_SWTRC_SEQUENCE_0 + ((x)*8))
+
+#define A_BCM1480_SWTRC_MATCH_DATA_VALUE(x) (A_BCM1480_SWTRC_MATCH_DATA_VALUE_0 + ((x)*16))
+#define A_BCM1480_SWTRC_MATCH_DATA_MASK(x) (A_BCM1480_SWTRC_MATCH_DATA_MASK_0 + ((x)*16))
+#define A_BCM1480_SWTRC_MATCH_TAG_VALUE(x) (A_BCM1480_SWTRC_MATCH_TAG_VALUE_0 + ((x)*16))
+#define A_BCM1480_SWTRC_MATCH_TAG_MASK(x) (A_BCM1480_SWTRC_MATCH_TAG_MASK_0 + ((x)*16))
+
+
+
+/*  *********************************************************************
+    *  High-Speed Port Registers (Section 13)
+    ********************************************************************* */
+
+#define A_BCM1480_HSP_BASE_0		    0x00DF810000
+#define A_BCM1480_HSP_BASE_1		    0x00DF890000
+#define A_BCM1480_HSP_BASE_2		    0x00DF910000
+#define BCM1480_HSP_REGISTER_SPACING	    0x80000
+
+#define A_BCM1480_HSP_BASE(idx)		    (A_BCM1480_HSP_BASE_0 + ((idx)*BCM1480_HSP_REGISTER_SPACING))
+#define A_BCM1480_HSP_REGISTER(idx, reg)     (A_BCM1480_HSP_BASE(idx) + (reg))
+
+#define R_BCM1480_HSP_RX_SPI4_CFG_0	      0x0000000000
+#define R_BCM1480_HSP_RX_SPI4_CFG_1	      0x0000000008
+#define R_BCM1480_HSP_RX_SPI4_DESKEW_OVERRIDE 0x0000000010
+#define R_BCM1480_HSP_RX_SPI4_DESKEW_DATAPATH 0x0000000018
+#define R_BCM1480_HSP_RX_SPI4_PORT_INT_EN     0x0000000020
+#define R_BCM1480_HSP_RX_SPI4_PORT_INT_STATUS 0x0000000028
+
+#define R_BCM1480_HSP_RX_SPI4_CALENDAR_0      0x0000000200
+#define R_BCM1480_HSP_RX_SPI4_CALENDAR_1      0x0000000208
+
+#define R_BCM1480_HSP_RX_PLL_CNFG	      0x0000000800
+#define R_BCM1480_HSP_RX_CALIBRATION	      0x0000000808
+#define R_BCM1480_HSP_RX_TEST		      0x0000000810
+#define R_BCM1480_HSP_RX_DIAG_DETAILS	      0x0000000818
+#define R_BCM1480_HSP_RX_DIAG_CRC_0	      0x0000000820
+#define R_BCM1480_HSP_RX_DIAG_CRC_1	      0x0000000828
+#define R_BCM1480_HSP_RX_DIAG_HTCMD	      0x0000000830
+#define R_BCM1480_HSP_RX_DIAG_PKTCTL	      0x0000000838
+
+#define R_BCM1480_HSP_RX_VIS_FLCTRL_COUNTER   0x0000000870
+
+#define R_BCM1480_HSP_RX_PKT_RAMALLOC_0	      0x0000020020
+#define R_BCM1480_HSP_RX_PKT_RAMALLOC_1	      0x0000020028
+#define R_BCM1480_HSP_RX_PKT_RAMALLOC_2	      0x0000020030
+#define R_BCM1480_HSP_RX_PKT_RAMALLOC_3	      0x0000020038
+#define R_BCM1480_HSP_RX_PKT_RAMALLOC_4	      0x0000020040
+#define R_BCM1480_HSP_RX_PKT_RAMALLOC_5	      0x0000020048
+#define R_BCM1480_HSP_RX_PKT_RAMALLOC_6	      0x0000020050
+#define R_BCM1480_HSP_RX_PKT_RAMALLOC_7	      0x0000020058
+#define R_BCM1480_HSP_RX_PKT_RAMALLOC(idx)    (R_BCM1480_HSP_RX_PKT_RAMALLOC_0 + 8*(idx))
+
+/* XXX Following registers were shuffled.  Renamed/renumbered per errata. */
+#define R_BCM1480_HSP_RX_HT_RAMALLOC_0	    0x0000020078
+#define R_BCM1480_HSP_RX_HT_RAMALLOC_1	    0x0000020080
+#define R_BCM1480_HSP_RX_HT_RAMALLOC_2	    0x0000020088
+#define R_BCM1480_HSP_RX_HT_RAMALLOC_3	    0x0000020090
+#define R_BCM1480_HSP_RX_HT_RAMALLOC_4	    0x0000020098
+#define R_BCM1480_HSP_RX_HT_RAMALLOC_5	    0x00000200A0
+
+#define R_BCM1480_HSP_RX_SPI_WATERMARK_0      0x00000200B0
+#define R_BCM1480_HSP_RX_SPI_WATERMARK_1      0x00000200B8
+#define R_BCM1480_HSP_RX_SPI_WATERMARK_2      0x00000200C0
+#define R_BCM1480_HSP_RX_SPI_WATERMARK_3      0x00000200C8
+#define R_BCM1480_HSP_RX_SPI_WATERMARK_4      0x00000200D0
+#define R_BCM1480_HSP_RX_SPI_WATERMARK_5      0x00000200D8
+#define R_BCM1480_HSP_RX_SPI_WATERMARK_6      0x00000200E0
+#define R_BCM1480_HSP_RX_SPI_WATERMARK_7      0x00000200E8
+#define R_BCM1480_HSP_RX_SPI_WATERMARK(idx)   (R_BCM1480_HSP_RX_SPI_WATERMARK_0 + 8*(idx))
+
+#define R_BCM1480_HSP_RX_VIS_CMDQ_0	      0x00000200F0
+#define R_BCM1480_HSP_RX_VIS_CMDQ_1	      0x00000200F8
+#define R_BCM1480_HSP_RX_VIS_CMDQ_2	      0x0000020100
+#define R_BCM1480_HSP_RX_RAM_READCTL	      0x0000020108
+#define R_BCM1480_HSP_RX_RAM_READWINDOW	      0x0000020110
+#define R_BCM1480_HSP_RX_RF_READCTL	      0x0000020118
+#define R_BCM1480_HSP_RX_RF_READWINDOW	      0x0000020120
+
+#define R_BCM1480_HSP_TX_SPI4_CFG_0	      0x0000040000
+#define R_BCM1480_HSP_TX_SPI4_CFG_1	      0x0000040008
+#define R_BCM1480_HSP_TX_SPI4_TRAINING_FMT    0x0000040010
+
+#define R_BCM1480_HSP_TX_PKT_RAMALLOC_0	      0x0000040020
+#define R_BCM1480_HSP_TX_PKT_RAMALLOC_1	      0x0000040028
+#define R_BCM1480_HSP_TX_PKT_RAMALLOC_2	      0x0000040030
+#define R_BCM1480_HSP_TX_PKT_RAMALLOC_3	      0x0000040038
+#define R_BCM1480_HSP_TX_PKT_RAMALLOC_4	      0x0000040040
+#define R_BCM1480_HSP_TX_PKT_RAMALLOC_5	      0x0000040048
+#define R_BCM1480_HSP_TX_PKT_RAMALLOC_6	      0x0000040050
+#define R_BCM1480_HSP_TX_PKT_RAMALLOC_7	      0x0000040058
+#define R_BCM1480_HSP_TX_PKT_RAMALLOC(idx)    (R_BCM1480_HSP_TX_PKT_RAMALLOC_0 + 8*(idx))
+#define R_BCM1480_HSP_TX_NPC_RAMALLOC	      0x0000040078
+#define R_BCM1480_HSP_TX_RSP_RAMALLOC	      0x0000040080
+#define R_BCM1480_HSP_TX_PC_RAMALLOC	      0x0000040088
+#define R_BCM1480_HSP_TX_HTCC_RAMALLOC_0      0x0000040090
+#define R_BCM1480_HSP_TX_HTCC_RAMALLOC_1      0x0000040098
+#define R_BCM1480_HSP_TX_HTCC_RAMALLOC_2      0x00000400A0
+
+#define R_BCM1480_HSP_TX_PKT_RXPHITCNT_0      0x00000400B0
+#define R_BCM1480_HSP_TX_PKT_RXPHITCNT_1      0x00000400B8
+#define R_BCM1480_HSP_TX_PKT_RXPHITCNT_2      0x00000400C0
+#define R_BCM1480_HSP_TX_PKT_RXPHITCNT_3      0x00000400C8
+#define R_BCM1480_HSP_TX_PKT_RXPHITCNT(idx)   (R_BCM1480_HSP_TX_PKT_RXPHITCNT_0 + 8*(idx))
+#define R_BCM1480_HSP_TX_HTIO_RXPHITCNT	      0x00000400D0
+#define R_BCM1480_HSP_TX_HTCC_RXPHITCNT	      0x00000400D8
+
+#define R_BCM1480_HSP_TX_PKT_TXPHITCNT_0      0x00000400E0
+#define R_BCM1480_HSP_TX_PKT_TXPHITCNT_1      0x00000400E8
+#define R_BCM1480_HSP_TX_PKT_TXPHITCNT_2      0x00000400F0
+#define R_BCM1480_HSP_TX_PKT_TXPHITCNT_3      0x00000400F8
+#define R_BCM1480_HSP_TX_PKT_TXPHITCNT(idx)   (R_BCM1480_HSP_TX_PKT_TXPHITCNT_0 + 8*(idx))
+#define R_BCM1480_HSP_TX_HTIO_TXPHITCNT	      0x0000040100
+#define R_BCM1480_HSP_TX_HTCC_TXPHITCNT	      0x0000040108
+
+#define R_BCM1480_HSP_TX_SPI4_CALENDAR_0      0x0000040200
+#define R_BCM1480_HSP_TX_SPI4_CALENDAR_1      0x0000040208
+
+#define R_BCM1480_HSP_TX_PLL_CNFG	      0x0000040800
+#define R_BCM1480_HSP_TX_CALIBRATION	      0x0000040808
+#define R_BCM1480_HSP_TX_TEST		      0x0000040810
+
+#define R_BCM1480_HSP_TX_VIS_CMDQ_0	      0x0000040840
+#define R_BCM1480_HSP_TX_VIS_CMDQ_1	      0x0000040848
+#define R_BCM1480_HSP_TX_VIS_CMDQ_2	      0x0000040850
+#define R_BCM1480_HSP_TX_RAM_READCTL	      0x0000040860
+#define R_BCM1480_HSP_TX_RAM_READWINDOW	      0x0000040868
+#define R_BCM1480_HSP_TX_RF_READCTL	      0x0000040870
+#define R_BCM1480_HSP_TX_RF_READWINDOW	      0x0000040878
+
+#define R_BCM1480_HSP_TX_SPI4_PORT_INT_STATUS 0x0000040880
+#define R_BCM1480_HSP_TX_SPI4_PORT_INT_EN     0x0000040888
+
+#define R_BCM1480_HSP_TX_NEXT_ADDR_BASE 0x000040400
+#define R_BCM1480_HSP_TX_NEXT_ADDR_REGISTER(x)	(R_BCM1480_HSP_TX_NEXT_ADDR_BASE+ 8*(x))
+
+
+
+/*  *********************************************************************
+    *  Physical Address Map (Table 10 and Figure 7)
+    ********************************************************************* */
+
+#define A_BCM1480_PHYS_MEMORY_0			_SB_MAKE64(0x0000000000)
+#define A_BCM1480_PHYS_MEMORY_SIZE		_SB_MAKE64((256*1024*1024))
+#define A_BCM1480_PHYS_SYSTEM_CTL		_SB_MAKE64(0x0010000000)
+#define A_BCM1480_PHYS_IO_SYSTEM		_SB_MAKE64(0x0010060000)
+#define A_BCM1480_PHYS_GENBUS			_SB_MAKE64(0x0010090000)
+#define A_BCM1480_PHYS_GENBUS_END		_SB_MAKE64(0x0028000000)
+#define A_BCM1480_PHYS_PCI_MISC_MATCH_BYTES	_SB_MAKE64(0x0028000000)
+#define A_BCM1480_PHYS_PCI_IACK_MATCH_BYTES	_SB_MAKE64(0x0029000000)
+#define A_BCM1480_PHYS_PCI_IO_MATCH_BYTES	_SB_MAKE64(0x002C000000)
+#define A_BCM1480_PHYS_PCI_CFG_MATCH_BYTES	_SB_MAKE64(0x002E000000)
+#define A_BCM1480_PHYS_PCI_OMAP_MATCH_BYTES	_SB_MAKE64(0x002F000000)
+#define A_BCM1480_PHYS_PCI_MEM_MATCH_BYTES	_SB_MAKE64(0x0030000000)
+#define A_BCM1480_PHYS_HT_MEM_MATCH_BYTES	_SB_MAKE64(0x0040000000)
+#define A_BCM1480_PHYS_HT_MEM_MATCH_BITS	_SB_MAKE64(0x0060000000)
+#define A_BCM1480_PHYS_MEMORY_1			_SB_MAKE64(0x0080000000)
+#define A_BCM1480_PHYS_MEMORY_2			_SB_MAKE64(0x0090000000)
+#define A_BCM1480_PHYS_PCI_MISC_MATCH_BITS	_SB_MAKE64(0x00A8000000)
+#define A_BCM1480_PHYS_PCI_IACK_MATCH_BITS	_SB_MAKE64(0x00A9000000)
+#define A_BCM1480_PHYS_PCI_IO_MATCH_BITS	_SB_MAKE64(0x00AC000000)
+#define A_BCM1480_PHYS_PCI_CFG_MATCH_BITS	_SB_MAKE64(0x00AE000000)
+#define A_BCM1480_PHYS_PCI_OMAP_MATCH_BITS	_SB_MAKE64(0x00AF000000)
+#define A_BCM1480_PHYS_PCI_MEM_MATCH_BITS	_SB_MAKE64(0x00B0000000)
+#define A_BCM1480_PHYS_MEMORY_3			_SB_MAKE64(0x00C0000000)
+#define A_BCM1480_PHYS_L2_CACHE_TEST		_SB_MAKE64(0x00D0000000)
+#define A_BCM1480_PHYS_HT_SPECIAL_MATCH_BYTES	_SB_MAKE64(0x00D8000000)
+#define A_BCM1480_PHYS_HT_IO_MATCH_BYTES	_SB_MAKE64(0x00DC000000)
+#define A_BCM1480_PHYS_HT_CFG_MATCH_BYTES	_SB_MAKE64(0x00DE000000)
+#define A_BCM1480_PHYS_HS_SUBSYS		_SB_MAKE64(0x00DF000000)
+#define A_BCM1480_PHYS_HT_SPECIAL_MATCH_BITS	_SB_MAKE64(0x00F8000000)
+#define A_BCM1480_PHYS_HT_IO_MATCH_BITS		_SB_MAKE64(0x00FC000000)
+#define A_BCM1480_PHYS_HT_CFG_MATCH_BITS	_SB_MAKE64(0x00FE000000)
+#define A_BCM1480_PHYS_MEMORY_EXP		_SB_MAKE64(0x0100000000)
+#define A_BCM1480_PHYS_MEMORY_EXP_SIZE		_SB_MAKE64((508*1024*1024*1024))
+#define A_BCM1480_PHYS_PCI_UPPER		_SB_MAKE64(0x1000000000)
+#define A_BCM1480_PHYS_HT_UPPER_MATCH_BYTES	_SB_MAKE64(0x2000000000)
+#define A_BCM1480_PHYS_HT_UPPER_MATCH_BITS	_SB_MAKE64(0x3000000000)
+#define A_BCM1480_PHYS_HT_NODE_ALIAS		_SB_MAKE64(0x4000000000)
+#define A_BCM1480_PHYS_HT_FULLACCESS		_SB_MAKE64(0xF000000000)
+
+
+/*  *********************************************************************
+    *  L2 Cache as RAM (Table 54)
+    ********************************************************************* */
+
+#define A_BCM1480_PHYS_L2CACHE_WAY_SIZE		_SB_MAKE64(0x0000020000)
+#define BCM1480_PHYS_L2CACHE_NUM_WAYS		8
+#define A_BCM1480_PHYS_L2CACHE_TOTAL_SIZE	_SB_MAKE64(0x0000100000)
+#define A_BCM1480_PHYS_L2CACHE_WAY0		_SB_MAKE64(0x00D0300000)
+#define A_BCM1480_PHYS_L2CACHE_WAY1		_SB_MAKE64(0x00D0320000)
+#define A_BCM1480_PHYS_L2CACHE_WAY2		_SB_MAKE64(0x00D0340000)
+#define A_BCM1480_PHYS_L2CACHE_WAY3		_SB_MAKE64(0x00D0360000)
+#define A_BCM1480_PHYS_L2CACHE_WAY4		_SB_MAKE64(0x00D0380000)
+#define A_BCM1480_PHYS_L2CACHE_WAY5		_SB_MAKE64(0x00D03A0000)
+#define A_BCM1480_PHYS_L2CACHE_WAY6		_SB_MAKE64(0x00D03C0000)
+#define A_BCM1480_PHYS_L2CACHE_WAY7		_SB_MAKE64(0x00D03E0000)
+
+#endif /* _BCM1480_REGS_H */
diff --git a/arch/mips/include/asm/sibyte/bcm1480_scd.h b/arch/mips/include/asm/sibyte/bcm1480_scd.h
new file mode 100644
index 000000000..87f37086d
--- /dev/null
+++ b/arch/mips/include/asm/sibyte/bcm1480_scd.h
@@ -0,0 +1,393 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*  *********************************************************************
+    *  BCM1280/BCM1400 Board Support Package
+    *
+    *  SCD Constants and Macros			    File: bcm1480_scd.h
+    *
+    *  This module contains constants and macros useful for
+    *  manipulating the System Control and Debug module.
+    *
+    *  BCM1400 specification level: 1X55_1X80-UM100-R (12/18/03)
+    *
+    *********************************************************************
+    *
+    *  Copyright 2000,2001,2002,2003,2004,2005
+    *  Broadcom Corporation. All rights reserved.
+    *
+    ********************************************************************* */
+
+#ifndef _BCM1480_SCD_H
+#define _BCM1480_SCD_H
+
+#include <asm/sibyte/sb1250_defs.h>
+
+/*  *********************************************************************
+    *  Pull in the BCM1250's SCD since lots of stuff is the same.
+    ********************************************************************* */
+
+#include <asm/sibyte/sb1250_scd.h>
+
+/*  *********************************************************************
+    *  Some general notes:
+    *
+    *  This file is basically a "what's new" header file.  Since the
+    *  BCM1250 and the new BCM1480 (and derivatives) share many common
+    *  features, this file contains only what's new or changed from
+    *  the 1250.  (above, you can see that we include the 1250 symbols
+    *  to get the base functionality).
+    *
+    *  In software, be sure to use the correct symbols, particularly
+    *  for blocks that are different between the two chip families.
+    *  All BCM1480-specific symbols have _BCM1480_ in their names,
+    *  and all BCM1250-specific and "base" functions that are common in
+    *  both chips have no special names (this is for compatibility with
+    *  older include files).  Therefore, if you're working with the
+    *  SCD, which is very different on each chip, A_SCD_xxx implies
+    *  the BCM1250 version and A_BCM1480_SCD_xxx implies the BCM1480
+    *  version.
+    ********************************************************************* */
+
+/*  *********************************************************************
+    *  System control/debug registers
+    ********************************************************************* */
+
+/*
+ * System Identification and Revision Register (Table 12)
+ * Register: SCD_SYSTEM_REVISION
+ * This register is field compatible with the 1250.
+ */
+
+/*
+ * New part definitions
+ */
+
+#define K_SYS_PART_BCM1480	    0x1406
+#define K_SYS_PART_BCM1280	    0x1206
+#define K_SYS_PART_BCM1455	    0x1407
+#define K_SYS_PART_BCM1255	    0x1257
+#define K_SYS_PART_BCM1158	    0x1156
+
+/*
+ * Manufacturing Information Register (Table 14)
+ * Register: SCD_SYSTEM_MANUF
+ */
+
+/*
+ * System Configuration Register (Table 15)
+ * Register: SCD_SYSTEM_CFG
+ * Entire register is different from 1250, all new constants below
+ */
+
+#define M_BCM1480_SYS_RESERVED0		    _SB_MAKEMASK1(0)
+#define M_BCM1480_SYS_HT_MINRSTCNT	    _SB_MAKEMASK1(1)
+#define M_BCM1480_SYS_RESERVED2		    _SB_MAKEMASK1(2)
+#define M_BCM1480_SYS_RESERVED3		    _SB_MAKEMASK1(3)
+#define M_BCM1480_SYS_RESERVED4		    _SB_MAKEMASK1(4)
+#define M_BCM1480_SYS_IOB_DIV		    _SB_MAKEMASK1(5)
+
+#define S_BCM1480_SYS_PLL_DIV		    _SB_MAKE64(6)
+#define M_BCM1480_SYS_PLL_DIV		    _SB_MAKEMASK(5, S_BCM1480_SYS_PLL_DIV)
+#define V_BCM1480_SYS_PLL_DIV(x)	    _SB_MAKEVALUE(x, S_BCM1480_SYS_PLL_DIV)
+#define G_BCM1480_SYS_PLL_DIV(x)	    _SB_GETVALUE(x, S_BCM1480_SYS_PLL_DIV, M_BCM1480_SYS_PLL_DIV)
+
+#define S_BCM1480_SYS_SW_DIV		    _SB_MAKE64(11)
+#define M_BCM1480_SYS_SW_DIV		    _SB_MAKEMASK(5, S_BCM1480_SYS_SW_DIV)
+#define V_BCM1480_SYS_SW_DIV(x)		    _SB_MAKEVALUE(x, S_BCM1480_SYS_SW_DIV)
+#define G_BCM1480_SYS_SW_DIV(x)		    _SB_GETVALUE(x, S_BCM1480_SYS_SW_DIV, M_BCM1480_SYS_SW_DIV)
+
+#define M_BCM1480_SYS_PCMCIA_ENABLE	    _SB_MAKEMASK1(16)
+#define M_BCM1480_SYS_DUART1_ENABLE	    _SB_MAKEMASK1(17)
+
+#define S_BCM1480_SYS_BOOT_MODE		    _SB_MAKE64(18)
+#define M_BCM1480_SYS_BOOT_MODE		    _SB_MAKEMASK(2, S_BCM1480_SYS_BOOT_MODE)
+#define V_BCM1480_SYS_BOOT_MODE(x)	    _SB_MAKEVALUE(x, S_BCM1480_SYS_BOOT_MODE)
+#define G_BCM1480_SYS_BOOT_MODE(x)	    _SB_GETVALUE(x, S_BCM1480_SYS_BOOT_MODE, M_BCM1480_SYS_BOOT_MODE)
+#define K_BCM1480_SYS_BOOT_MODE_ROM32	    0
+#define K_BCM1480_SYS_BOOT_MODE_ROM8	    1
+#define K_BCM1480_SYS_BOOT_MODE_SMBUS_SMALL 2
+#define K_BCM1480_SYS_BOOT_MODE_SMBUS_BIG   3
+#define M_BCM1480_SYS_BOOT_MODE_SMBUS	    _SB_MAKEMASK1(19)
+
+#define M_BCM1480_SYS_PCI_HOST		    _SB_MAKEMASK1(20)
+#define M_BCM1480_SYS_PCI_ARBITER	    _SB_MAKEMASK1(21)
+#define M_BCM1480_SYS_BIG_ENDIAN	    _SB_MAKEMASK1(22)
+#define M_BCM1480_SYS_GENCLK_EN		    _SB_MAKEMASK1(23)
+#define M_BCM1480_SYS_GEN_PARITY_EN	    _SB_MAKEMASK1(24)
+#define M_BCM1480_SYS_RESERVED25	    _SB_MAKEMASK1(25)
+
+#define S_BCM1480_SYS_CONFIG		    26
+#define M_BCM1480_SYS_CONFIG		    _SB_MAKEMASK(6, S_BCM1480_SYS_CONFIG)
+#define V_BCM1480_SYS_CONFIG(x)		    _SB_MAKEVALUE(x, S_BCM1480_SYS_CONFIG)
+#define G_BCM1480_SYS_CONFIG(x)		    _SB_GETVALUE(x, S_BCM1480_SYS_CONFIG, M_BCM1480_SYS_CONFIG)
+
+#define M_BCM1480_SYS_RESERVED32	    _SB_MAKEMASK(32, 15)
+
+#define S_BCM1480_SYS_NODEID		    47
+#define M_BCM1480_SYS_NODEID		    _SB_MAKEMASK(4, S_BCM1480_SYS_NODEID)
+#define V_BCM1480_SYS_NODEID(x)		    _SB_MAKEVALUE(x, S_BCM1480_SYS_NODEID)
+#define G_BCM1480_SYS_NODEID(x)		    _SB_GETVALUE(x, S_BCM1480_SYS_NODEID, M_BCM1480_SYS_NODEID)
+
+#define M_BCM1480_SYS_CCNUMA_EN		    _SB_MAKEMASK1(51)
+#define M_BCM1480_SYS_CPU_RESET_0	    _SB_MAKEMASK1(52)
+#define M_BCM1480_SYS_CPU_RESET_1	    _SB_MAKEMASK1(53)
+#define M_BCM1480_SYS_CPU_RESET_2	    _SB_MAKEMASK1(54)
+#define M_BCM1480_SYS_CPU_RESET_3	    _SB_MAKEMASK1(55)
+#define S_BCM1480_SYS_DISABLECPU0	    56
+#define M_BCM1480_SYS_DISABLECPU0	    _SB_MAKEMASK1(S_BCM1480_SYS_DISABLECPU0)
+#define S_BCM1480_SYS_DISABLECPU1	    57
+#define M_BCM1480_SYS_DISABLECPU1	    _SB_MAKEMASK1(S_BCM1480_SYS_DISABLECPU1)
+#define S_BCM1480_SYS_DISABLECPU2	    58
+#define M_BCM1480_SYS_DISABLECPU2	    _SB_MAKEMASK1(S_BCM1480_SYS_DISABLECPU2)
+#define S_BCM1480_SYS_DISABLECPU3	    59
+#define M_BCM1480_SYS_DISABLECPU3	    _SB_MAKEMASK1(S_BCM1480_SYS_DISABLECPU3)
+
+#define M_BCM1480_SYS_SB_SOFTRES	    _SB_MAKEMASK1(60)
+#define M_BCM1480_SYS_EXT_RESET		    _SB_MAKEMASK1(61)
+#define M_BCM1480_SYS_SYSTEM_RESET	    _SB_MAKEMASK1(62)
+#define M_BCM1480_SYS_SW_FLAG		    _SB_MAKEMASK1(63)
+
+/*
+ * Scratch Register (Table 16)
+ * Register: SCD_SYSTEM_SCRATCH
+ * Same as BCM1250
+ */
+
+
+/*
+ * Mailbox Registers (Table 17)
+ * Registers: SCD_MBOX_{0,1}_CPU_x
+ * Same as BCM1250
+ */
+
+
+/*
+ * See bcm1480_int.h for interrupt mapper registers.
+ */
+
+
+/*
+ * Watchdog Timer Initial Count Registers (Table 23)
+ * Registers: SCD_WDOG_INIT_CNT_x
+ *
+ * The watchdogs are almost the same as the 1250, except
+ * the configuration register has more bits to control the
+ * other CPUs.
+ */
+
+
+/*
+ * Watchdog Timer Configuration Registers (Table 25)
+ * Registers: SCD_WDOG_CFG_x
+ */
+
+#define M_BCM1480_SCD_WDOG_ENABLE	    _SB_MAKEMASK1(0)
+
+#define S_BCM1480_SCD_WDOG_RESET_TYPE	    2
+#define M_BCM1480_SCD_WDOG_RESET_TYPE	    _SB_MAKEMASK(5, S_BCM1480_SCD_WDOG_RESET_TYPE)
+#define V_BCM1480_SCD_WDOG_RESET_TYPE(x)    _SB_MAKEVALUE(x, S_BCM1480_SCD_WDOG_RESET_TYPE)
+#define G_BCM1480_SCD_WDOG_RESET_TYPE(x)    _SB_GETVALUE(x, S_BCM1480_SCD_WDOG_RESET_TYPE, M_BCM1480_SCD_WDOG_RESET_TYPE)
+
+#define K_BCM1480_SCD_WDOG_RESET_FULL	    0	/* actually, (x & 1) == 0  */
+#define K_BCM1480_SCD_WDOG_RESET_SOFT	    1
+#define K_BCM1480_SCD_WDOG_RESET_CPU0	    3
+#define K_BCM1480_SCD_WDOG_RESET_CPU1	    5
+#define K_BCM1480_SCD_WDOG_RESET_CPU2	    9
+#define K_BCM1480_SCD_WDOG_RESET_CPU3	    17
+#define K_BCM1480_SCD_WDOG_RESET_ALL_CPUS   31
+
+
+#define M_BCM1480_SCD_WDOG_HAS_RESET	    _SB_MAKEMASK1(8)
+
+/*
+ * General Timer Initial Count Registers (Table 26)
+ * Registers: SCD_TIMER_INIT_x
+ *
+ * The timer registers are the same as the BCM1250
+ */
+
+
+/*
+ * ZBbus Count Register (Table 29)
+ * Register: ZBBUS_CYCLE_COUNT
+ *
+ * Same as BCM1250
+ */
+
+/*
+ * ZBbus Compare Registers (Table 30)
+ * Registers: ZBBUS_CYCLE_CPx
+ *
+ * Same as BCM1250
+ */
+
+
+/*
+ * System Performance Counter Configuration Register (Table 31)
+ * Register: PERF_CNT_CFG_0
+ *
+ * SPC_CFG_SRC[0-3] is the same as the 1250.
+ * SPC_CFG_SRC[4-7] only exist on the 1480
+ * The clear/enable bits are in different locations on the 1250 and 1480.
+ */
+
+#define S_SPC_CFG_SRC4		    32
+#define M_SPC_CFG_SRC4		    _SB_MAKEMASK(8, S_SPC_CFG_SRC4)
+#define V_SPC_CFG_SRC4(x)	    _SB_MAKEVALUE(x, S_SPC_CFG_SRC4)
+#define G_SPC_CFG_SRC4(x)	    _SB_GETVALUE(x, S_SPC_CFG_SRC4, M_SPC_CFG_SRC4)
+
+#define S_SPC_CFG_SRC5		    40
+#define M_SPC_CFG_SRC5		    _SB_MAKEMASK(8, S_SPC_CFG_SRC5)
+#define V_SPC_CFG_SRC5(x)	    _SB_MAKEVALUE(x, S_SPC_CFG_SRC5)
+#define G_SPC_CFG_SRC5(x)	    _SB_GETVALUE(x, S_SPC_CFG_SRC5, M_SPC_CFG_SRC5)
+
+#define S_SPC_CFG_SRC6		    48
+#define M_SPC_CFG_SRC6		    _SB_MAKEMASK(8, S_SPC_CFG_SRC6)
+#define V_SPC_CFG_SRC6(x)	    _SB_MAKEVALUE(x, S_SPC_CFG_SRC6)
+#define G_SPC_CFG_SRC6(x)	    _SB_GETVALUE(x, S_SPC_CFG_SRC6, M_SPC_CFG_SRC6)
+
+#define S_SPC_CFG_SRC7		    56
+#define M_SPC_CFG_SRC7		    _SB_MAKEMASK(8, S_SPC_CFG_SRC7)
+#define V_SPC_CFG_SRC7(x)	    _SB_MAKEVALUE(x, S_SPC_CFG_SRC7)
+#define G_SPC_CFG_SRC7(x)	    _SB_GETVALUE(x, S_SPC_CFG_SRC7, M_SPC_CFG_SRC7)
+
+/*
+ * System Performance Counter Control Register (Table 32)
+ * Register: PERF_CNT_CFG_1
+ * BCM1480 specific
+ */
+#define M_BCM1480_SPC_CFG_CLEAR	    _SB_MAKEMASK1(0)
+#define M_BCM1480_SPC_CFG_ENABLE    _SB_MAKEMASK1(1)
+#if SIBYTE_HDR_FEATURE_CHIP(1480)
+#define M_SPC_CFG_CLEAR			M_BCM1480_SPC_CFG_CLEAR
+#define M_SPC_CFG_ENABLE		M_BCM1480_SPC_CFG_ENABLE
+#endif
+
+/*
+ * System Performance Counters (Table 33)
+ * Registers: PERF_CNT_x
+ */
+
+#define S_BCM1480_SPC_CNT_COUNT		    0
+#define M_BCM1480_SPC_CNT_COUNT		    _SB_MAKEMASK(40, S_BCM1480_SPC_CNT_COUNT)
+#define V_BCM1480_SPC_CNT_COUNT(x)	    _SB_MAKEVALUE(x, S_BCM1480_SPC_CNT_COUNT)
+#define G_BCM1480_SPC_CNT_COUNT(x)	    _SB_GETVALUE(x, S_BCM1480_SPC_CNT_COUNT, M_BCM1480_SPC_CNT_COUNT)
+
+#define M_BCM1480_SPC_CNT_OFLOW		    _SB_MAKEMASK1(40)
+
+
+/*
+ * Bus Watcher Error Status Register (Tables 36, 37)
+ * Registers: BUS_ERR_STATUS, BUS_ERR_STATUS_DEBUG
+ * Same as BCM1250.
+ */
+
+/*
+ * Bus Watcher Error Data Registers (Table 38)
+ * Registers: BUS_ERR_DATA_x
+ * Same as BCM1250.
+ */
+
+/*
+ * Bus Watcher L2 ECC Counter Register (Table 39)
+ * Register: BUS_L2_ERRORS
+ * Same as BCM1250.
+ */
+
+
+/*
+ * Bus Watcher Memory and I/O Error Counter Register (Table 40)
+ * Register: BUS_MEM_IO_ERRORS
+ * Same as BCM1250.
+ */
+
+
+/*
+ * Address Trap Registers
+ *
+ * Register layout same as BCM1250, almost.  The bus agents
+ * are different, and the address trap configuration bits are
+ * slightly different.
+ */
+
+#define M_BCM1480_ATRAP_INDEX		  _SB_MAKEMASK(4, 0)
+#define M_BCM1480_ATRAP_ADDRESS		  _SB_MAKEMASK(40, 0)
+
+#define S_BCM1480_ATRAP_CFG_CNT		   0
+#define M_BCM1480_ATRAP_CFG_CNT		   _SB_MAKEMASK(3, S_BCM1480_ATRAP_CFG_CNT)
+#define V_BCM1480_ATRAP_CFG_CNT(x)	   _SB_MAKEVALUE(x, S_BCM1480_ATRAP_CFG_CNT)
+#define G_BCM1480_ATRAP_CFG_CNT(x)	   _SB_GETVALUE(x, S_BCM1480_ATRAP_CFG_CNT, M_BCM1480_ATRAP_CFG_CNT)
+
+#define M_BCM1480_ATRAP_CFG_WRITE	   _SB_MAKEMASK1(3)
+#define M_BCM1480_ATRAP_CFG_ALL		   _SB_MAKEMASK1(4)
+#define M_BCM1480_ATRAP_CFG_INV		   _SB_MAKEMASK1(5)
+#define M_BCM1480_ATRAP_CFG_USESRC	   _SB_MAKEMASK1(6)
+#define M_BCM1480_ATRAP_CFG_SRCINV	   _SB_MAKEMASK1(7)
+
+#define S_BCM1480_ATRAP_CFG_AGENTID	8
+#define M_BCM1480_ATRAP_CFG_AGENTID	_SB_MAKEMASK(4, S_BCM1480_ATRAP_CFG_AGENTID)
+#define V_BCM1480_ATRAP_CFG_AGENTID(x)	_SB_MAKEVALUE(x, S_BCM1480_ATRAP_CFG_AGENTID)
+#define G_BCM1480_ATRAP_CFG_AGENTID(x)	_SB_GETVALUE(x, S_BCM1480_ATRAP_CFG_AGENTID, M_BCM1480_ATRAP_CFG_AGENTID)
+
+
+#define K_BCM1480_BUS_AGENT_CPU0	    0
+#define K_BCM1480_BUS_AGENT_CPU1	    1
+#define K_BCM1480_BUS_AGENT_NC		    2
+#define K_BCM1480_BUS_AGENT_IOB		    3
+#define K_BCM1480_BUS_AGENT_SCD		    4
+#define K_BCM1480_BUS_AGENT_L2C		    6
+#define K_BCM1480_BUS_AGENT_MC		    7
+#define K_BCM1480_BUS_AGENT_CPU2	    8
+#define K_BCM1480_BUS_AGENT_CPU3	    9
+#define K_BCM1480_BUS_AGENT_PM		    10
+
+#define S_BCM1480_ATRAP_CFG_CATTR	    12
+#define M_BCM1480_ATRAP_CFG_CATTR	    _SB_MAKEMASK(2, S_BCM1480_ATRAP_CFG_CATTR)
+#define V_BCM1480_ATRAP_CFG_CATTR(x)	    _SB_MAKEVALUE(x, S_BCM1480_ATRAP_CFG_CATTR)
+#define G_BCM1480_ATRAP_CFG_CATTR(x)	    _SB_GETVALUE(x, S_BCM1480_ATRAP_CFG_CATTR, M_BCM1480_ATRAP_CFG_CATTR)
+
+#define K_BCM1480_ATRAP_CFG_CATTR_IGNORE    0
+#define K_BCM1480_ATRAP_CFG_CATTR_UNC	    1
+#define K_BCM1480_ATRAP_CFG_CATTR_NONCOH    2
+#define K_BCM1480_ATRAP_CFG_CATTR_COHERENT  3
+
+#define M_BCM1480_ATRAP_CFG_CATTRINV	    _SB_MAKEMASK1(14)
+
+
+/*
+ * Trace Event Registers (Table 47)
+ * Same as BCM1250.
+ */
+
+/*
+ * Trace Sequence Control Registers (Table 48)
+ * Registers: TRACE_SEQUENCE_x
+ *
+ * Same as BCM1250 except for two new fields.
+ */
+
+
+#define M_BCM1480_SCD_TRSEQ_TID_MATCH_EN    _SB_MAKEMASK1(25)
+
+#define S_BCM1480_SCD_TRSEQ_SWFUNC	    26
+#define M_BCM1480_SCD_TRSEQ_SWFUNC	    _SB_MAKEMASK(2, S_BCM1480_SCD_TRSEQ_SWFUNC)
+#define V_BCM1480_SCD_TRSEQ_SWFUNC(x)	    _SB_MAKEVALUE(x, S_BCM1480_SCD_TRSEQ_SWFUNC)
+#define G_BCM1480_SCD_TRSEQ_SWFUNC(x)	    _SB_GETVALUE(x, S_BCM1480_SCD_TRSEQ_SWFUNC, M_BCM1480_SCD_TRSEQ_SWFUNC)
+
+/*
+ * Trace Control Register (Table 49)
+ * Register: TRACE_CFG
+ *
+ * BCM1480 changes to this register (other than location of the CUR_ADDR field)
+ * are defined below.
+ */
+
+#define S_BCM1480_SCD_TRACE_CFG_MODE	    16
+#define M_BCM1480_SCD_TRACE_CFG_MODE	    _SB_MAKEMASK(2, S_BCM1480_SCD_TRACE_CFG_MODE)
+#define V_BCM1480_SCD_TRACE_CFG_MODE(x)	    _SB_MAKEVALUE(x, S_BCM1480_SCD_TRACE_CFG_MODE)
+#define G_BCM1480_SCD_TRACE_CFG_MODE(x)	    _SB_GETVALUE(x, S_BCM1480_SCD_TRACE_CFG_MODE, M_BCM1480_SCD_TRACE_CFG_MODE)
+
+#define K_BCM1480_SCD_TRACE_CFG_MODE_BLOCKERS	0
+#define K_BCM1480_SCD_TRACE_CFG_MODE_BYTEEN_INT 1
+#define K_BCM1480_SCD_TRACE_CFG_MODE_FLOW_ID	2
+
+#endif /* _BCM1480_SCD_H */
diff --git a/arch/mips/include/asm/sibyte/bigsur.h b/arch/mips/include/asm/sibyte/bigsur.h
new file mode 100644
index 000000000..86c876196
--- /dev/null
+++ b/arch/mips/include/asm/sibyte/bigsur.h
@@ -0,0 +1,35 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2000,2001,2002,2003,2004 Broadcom Corporation
+ */
+#ifndef __ASM_SIBYTE_BIGSUR_H
+#define __ASM_SIBYTE_BIGSUR_H
+
+#include <asm/sibyte/sb1250.h>
+#include <asm/sibyte/bcm1480_int.h>
+
+#ifdef CONFIG_SIBYTE_BIGSUR
+#define SIBYTE_BOARD_NAME "BCM91x80A/B (BigSur)"
+#define SIBYTE_HAVE_PCMCIA 1
+#define SIBYTE_HAVE_IDE	   1
+#endif
+
+/* Generic bus chip selects */
+#define LEDS_CS		3
+#define LEDS_PHYS	0x100a0000
+
+#ifdef SIBYTE_HAVE_IDE
+#define IDE_CS		4
+#define IDE_PHYS	0x100b0000
+#define K_GPIO_GB_IDE	4
+#define K_INT_GB_IDE	(K_INT_GPIO_0 + K_GPIO_GB_IDE)
+#endif
+
+#ifdef SIBYTE_HAVE_PCMCIA
+#define PCMCIA_CS	6
+#define PCMCIA_PHYS	0x11000000
+#define K_GPIO_PC_READY 9
+#define K_INT_PC_READY	(K_INT_GPIO_0 + K_GPIO_PC_READY)
+#endif
+
+#endif /* __ASM_SIBYTE_BIGSUR_H */
diff --git a/arch/mips/include/asm/sibyte/board.h b/arch/mips/include/asm/sibyte/board.h
new file mode 100644
index 000000000..20fe2f16c
--- /dev/null
+++ b/arch/mips/include/asm/sibyte/board.h
@@ -0,0 +1,55 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2000,2001,2002,2003,2004 Broadcom Corporation
+ */
+
+#ifndef _SIBYTE_BOARD_H
+#define _SIBYTE_BOARD_H
+
+#if defined(CONFIG_SIBYTE_SWARM) || defined(CONFIG_SIBYTE_CRHONE) || \
+    defined(CONFIG_SIBYTE_CRHINE) || defined(CONFIG_SIBYTE_LITTLESUR)
+#include <asm/sibyte/swarm.h>
+#endif
+
+#if defined(CONFIG_SIBYTE_SENTOSA) || defined(CONFIG_SIBYTE_RHONE)
+#include <asm/sibyte/sentosa.h>
+#endif
+
+#ifdef CONFIG_SIBYTE_CARMEL
+#include <asm/sibyte/carmel.h>
+#endif
+
+#ifdef CONFIG_SIBYTE_BIGSUR
+#include <asm/sibyte/bigsur.h>
+#endif
+
+#ifdef __ASSEMBLY__
+
+#ifdef LEDS_PHYS
+#define setleds(t0, t1, c0, c1, c2, c3) \
+	li	t0, (LEDS_PHYS|0xa0000000); \
+	li	t1, c0; \
+	sb	t1, 0x18(t0); \
+	li	t1, c1; \
+	sb	t1, 0x10(t0); \
+	li	t1, c2; \
+	sb	t1, 0x08(t0); \
+	li	t1, c3; \
+	sb	t1, 0x00(t0)
+#else
+#define setleds(t0, t1, c0, c1, c2, c3)
+#endif /* LEDS_PHYS */
+
+#else
+
+void swarm_setup(void);
+
+#ifdef LEDS_PHYS
+extern void setleds(char *str);
+#else
+#define setleds(s) do { } while (0)
+#endif /* LEDS_PHYS */
+
+#endif /* __ASSEMBLY__ */
+
+#endif /* _SIBYTE_BOARD_H */
diff --git a/arch/mips/include/asm/sibyte/carmel.h b/arch/mips/include/asm/sibyte/carmel.h
new file mode 100644
index 000000000..c6730d7a6
--- /dev/null
+++ b/arch/mips/include/asm/sibyte/carmel.h
@@ -0,0 +1,45 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2002 Broadcom Corporation
+ */
+#ifndef __ASM_SIBYTE_CARMEL_H
+#define __ASM_SIBYTE_CARMEL_H
+
+#include <asm/sibyte/sb1250.h>
+#include <asm/sibyte/sb1250_int.h>
+
+#define SIBYTE_BOARD_NAME "Carmel"
+
+#define GPIO_PHY_INTERRUPT	2
+#define GPIO_NONMASKABLE_INT	3
+#define GPIO_CF_INSERTED	6
+#define GPIO_MONTEREY_RESET	7
+#define GPIO_QUADUART_INT	8
+#define GPIO_CF_INT		9
+#define GPIO_FPGA_CCLK		10
+#define GPIO_FPGA_DOUT		11
+#define GPIO_FPGA_DIN		12
+#define GPIO_FPGA_PGM		13
+#define GPIO_FPGA_DONE		14
+#define GPIO_FPGA_INIT		15
+
+#define LEDS_CS			2
+#define LEDS_PHYS		0x100C0000
+#define MLEDS_CS		3
+#define MLEDS_PHYS		0x100A0000
+#define UART_CS			4
+#define UART_PHYS		0x100D0000
+#define ARAVALI_CS		5
+#define ARAVALI_PHYS		0x11000000
+#define IDE_CS			6
+#define IDE_PHYS		0x100B0000
+#define ARAVALI2_CS		7
+#define ARAVALI2_PHYS		0x100E0000
+
+#if defined(CONFIG_SIBYTE_CARMEL)
+#define K_GPIO_GB_IDE	9
+#define K_INT_GB_IDE	(K_INT_GPIO_0 + K_GPIO_GB_IDE)
+#endif
+
+
+#endif /* __ASM_SIBYTE_CARMEL_H */
diff --git a/arch/mips/include/asm/sibyte/sb1250.h b/arch/mips/include/asm/sibyte/sb1250.h
new file mode 100644
index 000000000..495b31925
--- /dev/null
+++ b/arch/mips/include/asm/sibyte/sb1250.h
@@ -0,0 +1,54 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2000, 2001, 2002, 2003 Broadcom Corporation
+ */
+
+#ifndef _ASM_SIBYTE_SB1250_H
+#define _ASM_SIBYTE_SB1250_H
+
+/*
+ * yymmddpp: year, month, day, patch.
+ * should sync with Makefile EXTRAVERSION
+ */
+#define SIBYTE_RELEASE 0x02111403
+
+#define SB1250_NR_IRQS 64
+
+#define BCM1480_NR_IRQS			128
+#define BCM1480_NR_IRQS_HALF		64
+
+#define SB1250_DUART_MINOR_BASE		64
+
+#ifndef __ASSEMBLY__
+
+#include <asm/addrspace.h>
+
+/* For revision/pass information */
+#include <asm/sibyte/sb1250_scd.h>
+#include <asm/sibyte/bcm1480_scd.h>
+extern unsigned int sb1_pass;
+extern unsigned int soc_pass;
+extern unsigned int soc_type;
+extern unsigned int periph_rev;
+extern unsigned int zbbus_mhz;
+
+extern void sb1250_mask_irq(int cpu, int irq);
+extern void sb1250_unmask_irq(int cpu, int irq);
+
+extern void bcm1480_time_init(void);
+extern void bcm1480_mask_irq(int cpu, int irq);
+extern void bcm1480_unmask_irq(int cpu, int irq);
+
+#define AT_spin \
+	__asm__ __volatile__ (		\
+		".set noat\n"		\
+		"li $at, 0\n"		\
+		"1: beqz $at, 1b\n"	\
+		".set at\n"		\
+		)
+
+#endif
+
+#define IOADDR(a) ((void __iomem *)(IO_BASE + (a)))
+
+#endif
diff --git a/arch/mips/include/asm/sibyte/sb1250_defs.h b/arch/mips/include/asm/sibyte/sb1250_defs.h
new file mode 100644
index 000000000..68cd7c0b3
--- /dev/null
+++ b/arch/mips/include/asm/sibyte/sb1250_defs.h
@@ -0,0 +1,246 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*  *********************************************************************
+    *  SB1250 Board Support Package
+    *
+    *  Global constants and macros		File: sb1250_defs.h
+    *
+    *  This file contains macros and definitions used by the other
+    *  include files.
+    *
+    *  SB1250 specification level:  User's manual 1/02/02
+    *
+    *********************************************************************
+    *
+    *  Copyright 2000,2001,2002,2003
+    *  Broadcom Corporation. All rights reserved.
+    *
+    ********************************************************************* */
+
+#ifndef _SB1250_DEFS_H
+#define _SB1250_DEFS_H
+
+/*
+ * These headers require ANSI C89 string concatenation, and GCC or other
+ * 'long long' (64-bit integer) support.
+ */
+#if !defined(__STDC__) && !defined(_MSC_VER)
+#error SiByte headers require ANSI C89 support
+#endif
+
+
+/*  *********************************************************************
+    *  Macros for feature tests, used to enable include file features
+    *  for chip features only present in certain chip revisions.
+    *
+    *  SIBYTE_HDR_FEATURES may be defined to be the mask value chip/revision
+    *  which is to be exposed by the headers.  If undefined, it defaults to
+    *  "all features."
+    *
+    *  Use like:
+    *
+    *	 #define SIBYTE_HDR_FEATURES	SIBYTE_HDR_FMASK_112x_PASS1
+    *
+    *		Generate defines only for that revision of chip.
+    *
+    *	 #if SIBYTE_HDR_FEATURE(chip,pass)
+    *
+    *		True if header features for that revision or later of
+    *		that particular chip type are enabled in SIBYTE_HDR_FEATURES.
+    *		(Use this to bracket #defines for features present in a given
+    *		revision and later.)
+    *
+    *		Note that there is no implied ordering between chip types.
+    *
+    *		Note also that 'chip' and 'pass' must textually exactly
+    *		match the defines below.  So, for example,
+    *		SIBYTE_HDR_FEATURE(112x, PASS1) is OK, but
+    *		SIBYTE_HDR_FEATURE(1120, pass1) is not (for two reasons).
+    *
+    *	 #if SIBYTE_HDR_FEATURE_UP_TO(chip,pass)
+    *
+    *		Same as SIBYTE_HDR_FEATURE, but true for the named revision
+    *		and earlier revisions of the named chip type.
+    *
+    *	 #if SIBYTE_HDR_FEATURE_EXACT(chip,pass)
+    *
+    *		Same as SIBYTE_HDR_FEATURE, but only true for the named
+    *		revision of the named chip type.  (Note that this CANNOT
+    *		be used to verify that you're compiling only for that
+    *		particular chip/revision.  It will be true any time this
+    *		chip/revision is included in SIBYTE_HDR_FEATURES.)
+    *
+    *	 #if SIBYTE_HDR_FEATURE_CHIP(chip)
+    *
+    *		True if header features for (any revision of) that chip type
+    *		are enabled in SIBYTE_HDR_FEATURES.  (Use this to bracket
+    *		#defines for features specific to a given chip type.)
+    *
+    *  Mask values currently include room for additional revisions of each
+    *  chip type, but can be renumbered at will.  Note that they MUST fit
+    *  into 31 bits and may not include C type constructs, for safe use in
+    *  CPP conditionals.  Bit positions within chip types DO indicate
+    *  ordering, so be careful when adding support for new minor revs.
+    ********************************************************************* */
+
+#define SIBYTE_HDR_FMASK_1250_ALL		0x000000ff
+#define SIBYTE_HDR_FMASK_1250_PASS1		0x00000001
+#define SIBYTE_HDR_FMASK_1250_PASS2		0x00000002
+#define SIBYTE_HDR_FMASK_1250_PASS3		0x00000004
+
+#define SIBYTE_HDR_FMASK_112x_ALL		0x00000f00
+#define SIBYTE_HDR_FMASK_112x_PASS1		0x00000100
+
+#define SIBYTE_HDR_FMASK_1480_ALL		0x0000f000
+#define SIBYTE_HDR_FMASK_1480_PASS1		0x00001000
+#define SIBYTE_HDR_FMASK_1480_PASS2		0x00002000
+
+/* Bit mask for chip/revision.	(use _ALL for all revisions of a chip).	 */
+#define SIBYTE_HDR_FMASK(chip, pass)					\
+    (SIBYTE_HDR_FMASK_ ## chip ## _ ## pass)
+#define SIBYTE_HDR_FMASK_ALLREVS(chip)					\
+    (SIBYTE_HDR_FMASK_ ## chip ## _ALL)
+
+/* Default constant value for all chips, all revisions */
+#define SIBYTE_HDR_FMASK_ALL						\
+    (SIBYTE_HDR_FMASK_1250_ALL | SIBYTE_HDR_FMASK_112x_ALL		\
+     | SIBYTE_HDR_FMASK_1480_ALL)
+
+/* This one is used for the "original" BCM1250/BCM112x chips.  We use this
+   to weed out constants and macros that do not exist on later chips like
+   the BCM1480	*/
+#define SIBYTE_HDR_FMASK_1250_112x_ALL					\
+    (SIBYTE_HDR_FMASK_1250_ALL | SIBYTE_HDR_FMASK_112x_ALL)
+#define SIBYTE_HDR_FMASK_1250_112x SIBYTE_HDR_FMASK_1250_112x_ALL
+
+#ifndef SIBYTE_HDR_FEATURES
+#define SIBYTE_HDR_FEATURES			SIBYTE_HDR_FMASK_ALL
+#endif
+
+
+/* Bit mask for revisions of chip exclusively before the named revision.  */
+#define SIBYTE_HDR_FMASK_BEFORE(chip, pass)				\
+    ((SIBYTE_HDR_FMASK(chip, pass) - 1) & SIBYTE_HDR_FMASK_ALLREVS(chip))
+
+/* Bit mask for revisions of chip exclusively after the named revision.	 */
+#define SIBYTE_HDR_FMASK_AFTER(chip, pass)				\
+    (~(SIBYTE_HDR_FMASK(chip, pass)					\
+     | (SIBYTE_HDR_FMASK(chip, pass) - 1)) & SIBYTE_HDR_FMASK_ALLREVS(chip))
+
+
+/* True if header features enabled for (any revision of) that chip type.  */
+#define SIBYTE_HDR_FEATURE_CHIP(chip)					\
+    (!! (SIBYTE_HDR_FMASK_ALLREVS(chip) & SIBYTE_HDR_FEATURES))
+
+/* True for all versions of the BCM1250 and BCM1125, but not true for
+   anything else */
+#define SIBYTE_HDR_FEATURE_1250_112x \
+      (SIBYTE_HDR_FEATURE_CHIP(1250) || SIBYTE_HDR_FEATURE_CHIP(112x))
+/*    (!!  (SIBYTE_HDR_FEATURES & SIBYHTE_HDR_FMASK_1250_112x)) */
+
+/* True if header features enabled for that rev or later, inclusive.  */
+#define SIBYTE_HDR_FEATURE(chip, pass)					\
+    (!! ((SIBYTE_HDR_FMASK(chip, pass)					\
+	  | SIBYTE_HDR_FMASK_AFTER(chip, pass)) & SIBYTE_HDR_FEATURES))
+
+/* True if header features enabled for exactly that rev.  */
+#define SIBYTE_HDR_FEATURE_EXACT(chip, pass)				\
+    (!! (SIBYTE_HDR_FMASK(chip, pass) & SIBYTE_HDR_FEATURES))
+
+/* True if header features enabled for that rev or before, inclusive.  */
+#define SIBYTE_HDR_FEATURE_UP_TO(chip, pass)				\
+    (!! ((SIBYTE_HDR_FMASK(chip, pass)					\
+	 | SIBYTE_HDR_FMASK_BEFORE(chip, pass)) & SIBYTE_HDR_FEATURES))
+
+
+/*  *********************************************************************
+    *  Naming schemes for constants in these files:
+    *
+    *  M_xxx	       MASK constant (identifies bits in a register).
+    *		       For multi-bit fields, all bits in the field will
+    *		       be set.
+    *
+    *  K_xxx	       "Code" constant (value for data in a multi-bit
+    *		       field).	The value is right justified.
+    *
+    *  V_xxx	       "Value" constant.  This is the same as the
+    *		       corresponding "K_xxx" constant, except it is
+    *		       shifted to the correct position in the register.
+    *
+    *  S_xxx	       SHIFT constant.	This is the number of bits that
+    *		       a field value (code) needs to be shifted
+    *		       (towards the left) to put the value in the right
+    *		       position for the register.
+    *
+    *  A_xxx	       ADDRESS constant.  This will be a physical
+    *		       address.	 Use the PHYS_TO_K1 macro to generate
+    *		       a K1SEG address.
+    *
+    *  R_xxx	       RELATIVE offset constant.  This is an offset from
+    *		       an A_xxx constant (usually the first register in
+    *		       a group).
+    *
+    *  G_xxx(X)	       GET value.  This macro obtains a multi-bit field
+    *		       from a register, masks it, and shifts it to
+    *		       the bottom of the register (retrieving a K_xxx
+    *		       value, for example).
+    *
+    *  V_xxx(X)	       VALUE.  This macro computes the value of a
+    *		       K_xxx constant shifted to the correct position
+    *		       in the register.
+    ********************************************************************* */
+
+
+
+
+/*
+ * Cast to 64-bit number.  Presumably the syntax is different in
+ * assembly language.
+ *
+ * Note: you'll need to define uint32_t and uint64_t in your headers.
+ */
+
+#if !defined(__ASSEMBLY__)
+#define _SB_MAKE64(x) ((uint64_t)(x))
+#define _SB_MAKE32(x) ((uint32_t)(x))
+#else
+#define _SB_MAKE64(x) (x)
+#define _SB_MAKE32(x) (x)
+#endif
+
+
+/*
+ * Make a mask for 1 bit at position 'n'
+ */
+
+#define _SB_MAKEMASK1(n) (_SB_MAKE64(1) << _SB_MAKE64(n))
+#define _SB_MAKEMASK1_32(n) (_SB_MAKE32(1) << _SB_MAKE32(n))
+
+/*
+ * Make a mask for 'v' bits at position 'n'
+ */
+
+#define _SB_MAKEMASK(v, n) (_SB_MAKE64((_SB_MAKE64(1)<<(v))-1) << _SB_MAKE64(n))
+#define _SB_MAKEMASK_32(v, n) (_SB_MAKE32((_SB_MAKE32(1)<<(v))-1) << _SB_MAKE32(n))
+
+/*
+ * Make a value at 'v' at bit position 'n'
+ */
+
+#define _SB_MAKEVALUE(v, n) (_SB_MAKE64(v) << _SB_MAKE64(n))
+#define _SB_MAKEVALUE_32(v, n) (_SB_MAKE32(v) << _SB_MAKE32(n))
+
+#define _SB_GETVALUE(v, n, m) ((_SB_MAKE64(v) & _SB_MAKE64(m)) >> _SB_MAKE64(n))
+#define _SB_GETVALUE_32(v, n, m) ((_SB_MAKE32(v) & _SB_MAKE32(m)) >> _SB_MAKE32(n))
+
+/*
+ * Macros to read/write on-chip registers
+ * XXX should we do the PHYS_TO_K1 here?
+ */
+
+
+#if defined(__mips64) && !defined(__ASSEMBLY__)
+#define SBWRITECSR(csr, val) *((volatile uint64_t *) PHYS_TO_K1(csr)) = (val)
+#define SBREADCSR(csr) (*((volatile uint64_t *) PHYS_TO_K1(csr)))
+#endif /* __ASSEMBLY__ */
+
+#endif
diff --git a/arch/mips/include/asm/sibyte/sb1250_dma.h b/arch/mips/include/asm/sibyte/sb1250_dma.h
new file mode 100644
index 000000000..d9678b98c
--- /dev/null
+++ b/arch/mips/include/asm/sibyte/sb1250_dma.h
@@ -0,0 +1,581 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*  *********************************************************************
+    *  SB1250 Board Support Package
+    *
+    *  DMA definitions				File: sb1250_dma.h
+    *
+    *  This module contains constants and macros useful for
+    *  programming the SB1250's DMA controllers, both the data mover
+    *  and the Ethernet DMA.
+    *
+    *  SB1250 specification level:  User's manual 10/21/02
+    *  BCM1280 specification level: User's manual 11/24/03
+    *
+    *********************************************************************
+    *
+    *  Copyright 2000,2001,2002,2003
+    *  Broadcom Corporation. All rights reserved.
+    *
+    ********************************************************************* */
+
+
+#ifndef _SB1250_DMA_H
+#define _SB1250_DMA_H
+
+
+#include <asm/sibyte/sb1250_defs.h>
+
+/*  *********************************************************************
+    *  DMA Registers
+    ********************************************************************* */
+
+/*
+ * Ethernet and Serial DMA Configuration Register 0  (Table 7-4)
+ * Registers: DMA_CONFIG0_MAC_x_RX_CH_0
+ * Registers: DMA_CONFIG0_MAC_x_TX_CH_0
+ * Registers: DMA_CONFIG0_SER_x_RX
+ * Registers: DMA_CONFIG0_SER_x_TX
+ */
+
+
+#define M_DMA_DROP		    _SB_MAKEMASK1(0)
+
+#define M_DMA_CHAIN_SEL		    _SB_MAKEMASK1(1)
+#define M_DMA_RESERVED1		    _SB_MAKEMASK1(2)
+
+#define S_DMA_DESC_TYPE		    _SB_MAKE64(1)
+#define M_DMA_DESC_TYPE		    _SB_MAKEMASK(2, S_DMA_DESC_TYPE)
+#define V_DMA_DESC_TYPE(x)	    _SB_MAKEVALUE(x, S_DMA_DESC_TYPE)
+#define G_DMA_DESC_TYPE(x)	    _SB_GETVALUE(x, S_DMA_DESC_TYPE, M_DMA_DESC_TYPE)
+
+#define K_DMA_DESC_TYPE_RING_AL		0
+#define K_DMA_DESC_TYPE_CHAIN_AL	1
+
+#if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define K_DMA_DESC_TYPE_RING_UAL_WI	2
+#define K_DMA_DESC_TYPE_RING_UAL_RMW	3
+#endif /* 1250 PASS3 || 112x PASS1 || 1480 */
+
+#define M_DMA_EOP_INT_EN	    _SB_MAKEMASK1(3)
+#define M_DMA_HWM_INT_EN	    _SB_MAKEMASK1(4)
+#define M_DMA_LWM_INT_EN	    _SB_MAKEMASK1(5)
+#define M_DMA_TBX_EN		    _SB_MAKEMASK1(6)
+#define M_DMA_TDX_EN		    _SB_MAKEMASK1(7)
+
+#define S_DMA_INT_PKTCNT	    _SB_MAKE64(8)
+#define M_DMA_INT_PKTCNT	    _SB_MAKEMASK(8, S_DMA_INT_PKTCNT)
+#define V_DMA_INT_PKTCNT(x)	    _SB_MAKEVALUE(x, S_DMA_INT_PKTCNT)
+#define G_DMA_INT_PKTCNT(x)	    _SB_GETVALUE(x, S_DMA_INT_PKTCNT, M_DMA_INT_PKTCNT)
+
+#define S_DMA_RINGSZ		    _SB_MAKE64(16)
+#define M_DMA_RINGSZ		    _SB_MAKEMASK(16, S_DMA_RINGSZ)
+#define V_DMA_RINGSZ(x)		    _SB_MAKEVALUE(x, S_DMA_RINGSZ)
+#define G_DMA_RINGSZ(x)		    _SB_GETVALUE(x, S_DMA_RINGSZ, M_DMA_RINGSZ)
+
+#define S_DMA_HIGH_WATERMARK	    _SB_MAKE64(32)
+#define M_DMA_HIGH_WATERMARK	    _SB_MAKEMASK(16, S_DMA_HIGH_WATERMARK)
+#define V_DMA_HIGH_WATERMARK(x)	    _SB_MAKEVALUE(x, S_DMA_HIGH_WATERMARK)
+#define G_DMA_HIGH_WATERMARK(x)	    _SB_GETVALUE(x, S_DMA_HIGH_WATERMARK, M_DMA_HIGH_WATERMARK)
+
+#define S_DMA_LOW_WATERMARK	    _SB_MAKE64(48)
+#define M_DMA_LOW_WATERMARK	    _SB_MAKEMASK(16, S_DMA_LOW_WATERMARK)
+#define V_DMA_LOW_WATERMARK(x)	    _SB_MAKEVALUE(x, S_DMA_LOW_WATERMARK)
+#define G_DMA_LOW_WATERMARK(x)	    _SB_GETVALUE(x, S_DMA_LOW_WATERMARK, M_DMA_LOW_WATERMARK)
+
+/*
+ * Ethernet and Serial DMA Configuration Register 1 (Table 7-5)
+ * Registers: DMA_CONFIG1_MAC_x_RX_CH_0
+ * Registers: DMA_CONFIG1_DMA_x_TX_CH_0
+ * Registers: DMA_CONFIG1_SER_x_RX
+ * Registers: DMA_CONFIG1_SER_x_TX
+ */
+
+#define M_DMA_HDR_CF_EN		    _SB_MAKEMASK1(0)
+#define M_DMA_ASIC_XFR_EN	    _SB_MAKEMASK1(1)
+#define M_DMA_PRE_ADDR_EN	    _SB_MAKEMASK1(2)
+#define M_DMA_FLOW_CTL_EN	    _SB_MAKEMASK1(3)
+#define M_DMA_NO_DSCR_UPDT	    _SB_MAKEMASK1(4)
+#define M_DMA_L2CA		    _SB_MAKEMASK1(5)
+
+#if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define M_DMA_RX_XTRA_STATUS	    _SB_MAKEMASK1(6)
+#define M_DMA_TX_CPU_PAUSE	    _SB_MAKEMASK1(6)
+#define M_DMA_TX_FC_PAUSE_EN	    _SB_MAKEMASK1(7)
+#endif /* 1250 PASS3 || 112x PASS1 || 1480 */
+
+#define M_DMA_MBZ1		    _SB_MAKEMASK(6, 15)
+
+#define S_DMA_HDR_SIZE		    _SB_MAKE64(21)
+#define M_DMA_HDR_SIZE		    _SB_MAKEMASK(9, S_DMA_HDR_SIZE)
+#define V_DMA_HDR_SIZE(x)	    _SB_MAKEVALUE(x, S_DMA_HDR_SIZE)
+#define G_DMA_HDR_SIZE(x)	    _SB_GETVALUE(x, S_DMA_HDR_SIZE, M_DMA_HDR_SIZE)
+
+#define M_DMA_MBZ2		    _SB_MAKEMASK(5, 32)
+
+#define S_DMA_ASICXFR_SIZE	    _SB_MAKE64(37)
+#define M_DMA_ASICXFR_SIZE	    _SB_MAKEMASK(9, S_DMA_ASICXFR_SIZE)
+#define V_DMA_ASICXFR_SIZE(x)	    _SB_MAKEVALUE(x, S_DMA_ASICXFR_SIZE)
+#define G_DMA_ASICXFR_SIZE(x)	    _SB_GETVALUE(x, S_DMA_ASICXFR_SIZE, M_DMA_ASICXFR_SIZE)
+
+#define S_DMA_INT_TIMEOUT	    _SB_MAKE64(48)
+#define M_DMA_INT_TIMEOUT	    _SB_MAKEMASK(16, S_DMA_INT_TIMEOUT)
+#define V_DMA_INT_TIMEOUT(x)	    _SB_MAKEVALUE(x, S_DMA_INT_TIMEOUT)
+#define G_DMA_INT_TIMEOUT(x)	    _SB_GETVALUE(x, S_DMA_INT_TIMEOUT, M_DMA_INT_TIMEOUT)
+
+/*
+ * Ethernet and Serial DMA Descriptor base address (Table 7-6)
+ */
+
+#define M_DMA_DSCRBASE_MBZ	    _SB_MAKEMASK(4, 0)
+
+
+/*
+ * ASIC Mode Base Address (Table 7-7)
+ */
+
+#define M_DMA_ASIC_BASE_MBZ	    _SB_MAKEMASK(20, 0)
+
+/*
+ * DMA Descriptor Count Registers (Table 7-8)
+ */
+
+/* No bitfields */
+
+
+/*
+ * Current Descriptor Address Register (Table 7-11)
+ */
+
+#define S_DMA_CURDSCR_ADDR	    _SB_MAKE64(0)
+#define M_DMA_CURDSCR_ADDR	    _SB_MAKEMASK(40, S_DMA_CURDSCR_ADDR)
+#define S_DMA_CURDSCR_COUNT	    _SB_MAKE64(40)
+#define M_DMA_CURDSCR_COUNT	    _SB_MAKEMASK(16, S_DMA_CURDSCR_COUNT)
+
+#if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define M_DMA_TX_CH_PAUSE_ON	    _SB_MAKEMASK1(56)
+#endif /* 1250 PASS3 || 112x PASS1 || 1480 */
+
+/*
+ * Receive Packet Drop Registers
+ */
+#if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define S_DMA_OODLOST_RX	   _SB_MAKE64(0)
+#define M_DMA_OODLOST_RX	   _SB_MAKEMASK(16, S_DMA_OODLOST_RX)
+#define G_DMA_OODLOST_RX(x)	   _SB_GETVALUE(x, S_DMA_OODLOST_RX, M_DMA_OODLOST_RX)
+
+#define S_DMA_EOP_COUNT_RX	   _SB_MAKE64(16)
+#define M_DMA_EOP_COUNT_RX	   _SB_MAKEMASK(8, S_DMA_EOP_COUNT_RX)
+#define G_DMA_EOP_COUNT_RX(x)	   _SB_GETVALUE(x, S_DMA_EOP_COUNT_RX, M_DMA_EOP_COUNT_RX)
+#endif /* 1250 PASS3 || 112x PASS1 || 1480 */
+
+/*  *********************************************************************
+    *  DMA Descriptors
+    ********************************************************************* */
+
+/*
+ * Descriptor doubleword "A"  (Table 7-12)
+ */
+
+#define S_DMA_DSCRA_OFFSET	    _SB_MAKE64(0)
+#define M_DMA_DSCRA_OFFSET	    _SB_MAKEMASK(5, S_DMA_DSCRA_OFFSET)
+#define V_DMA_DSCRA_OFFSET(x)	    _SB_MAKEVALUE(x, S_DMA_DSCRA_OFFSET)
+#define G_DMA_DSCRA_OFFSET(x)	    _SB_GETVALUE(x, S_DMA_DSCRA_OFFSET, M_DMA_DSCRA_OFFSET)
+
+/* Note: Don't shift the address over, just mask it with the mask below */
+#define S_DMA_DSCRA_A_ADDR	    _SB_MAKE64(5)
+#define M_DMA_DSCRA_A_ADDR	    _SB_MAKEMASK(35, S_DMA_DSCRA_A_ADDR)
+
+#define M_DMA_DSCRA_A_ADDR_OFFSET   (M_DMA_DSCRA_OFFSET | M_DMA_DSCRA_A_ADDR)
+
+#if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define S_DMA_DSCRA_A_ADDR_UA	     _SB_MAKE64(0)
+#define M_DMA_DSCRA_A_ADDR_UA	     _SB_MAKEMASK(40, S_DMA_DSCRA_A_ADDR_UA)
+#endif /* 1250 PASS3 || 112x PASS1 || 1480 */
+
+#define S_DMA_DSCRA_A_SIZE	    _SB_MAKE64(40)
+#define M_DMA_DSCRA_A_SIZE	    _SB_MAKEMASK(9, S_DMA_DSCRA_A_SIZE)
+#define V_DMA_DSCRA_A_SIZE(x)	    _SB_MAKEVALUE(x, S_DMA_DSCRA_A_SIZE)
+#define G_DMA_DSCRA_A_SIZE(x)	    _SB_GETVALUE(x, S_DMA_DSCRA_A_SIZE, M_DMA_DSCRA_A_SIZE)
+
+#if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define S_DMA_DSCRA_DSCR_CNT	    _SB_MAKE64(40)
+#define M_DMA_DSCRA_DSCR_CNT	    _SB_MAKEMASK(8, S_DMA_DSCRA_DSCR_CNT)
+#define G_DMA_DSCRA_DSCR_CNT(x)	    _SB_GETVALUE(x, S_DMA_DSCRA_DSCR_CNT, M_DMA_DSCRA_DSCR_CNT)
+#endif /* 1250 PASS3 || 112x PASS1 || 1480 */
+
+#define M_DMA_DSCRA_INTERRUPT	    _SB_MAKEMASK1(49)
+#define M_DMA_DSCRA_OFFSETB	    _SB_MAKEMASK1(50)
+
+#define S_DMA_DSCRA_STATUS	    _SB_MAKE64(51)
+#define M_DMA_DSCRA_STATUS	    _SB_MAKEMASK(13, S_DMA_DSCRA_STATUS)
+#define V_DMA_DSCRA_STATUS(x)	    _SB_MAKEVALUE(x, S_DMA_DSCRA_STATUS)
+#define G_DMA_DSCRA_STATUS(x)	    _SB_GETVALUE(x, S_DMA_DSCRA_STATUS, M_DMA_DSCRA_STATUS)
+
+/*
+ * Descriptor doubleword "B"  (Table 7-13)
+ */
+
+
+#define S_DMA_DSCRB_OPTIONS	    _SB_MAKE64(0)
+#define M_DMA_DSCRB_OPTIONS	    _SB_MAKEMASK(4, S_DMA_DSCRB_OPTIONS)
+#define V_DMA_DSCRB_OPTIONS(x)	    _SB_MAKEVALUE(x, S_DMA_DSCRB_OPTIONS)
+#define G_DMA_DSCRB_OPTIONS(x)	    _SB_GETVALUE(x, S_DMA_DSCRB_OPTIONS, M_DMA_DSCRB_OPTIONS)
+
+#if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define S_DMA_DSCRB_A_SIZE	  _SB_MAKE64(8)
+#define M_DMA_DSCRB_A_SIZE	  _SB_MAKEMASK(14, S_DMA_DSCRB_A_SIZE)
+#define V_DMA_DSCRB_A_SIZE(x)	  _SB_MAKEVALUE(x, S_DMA_DSCRB_A_SIZE)
+#define G_DMA_DSCRB_A_SIZE(x)	  _SB_GETVALUE(x, S_DMA_DSCRB_A_SIZE, M_DMA_DSCRB_A_SIZE)
+#endif /* 1250 PASS3 || 112x PASS1 || 1480 */
+
+#define R_DMA_DSCRB_ADDR	    _SB_MAKE64(0x10)
+
+/* Note: Don't shift the address over, just mask it with the mask below */
+#define S_DMA_DSCRB_B_ADDR	    _SB_MAKE64(5)
+#define M_DMA_DSCRB_B_ADDR	    _SB_MAKEMASK(35, S_DMA_DSCRB_B_ADDR)
+
+#define S_DMA_DSCRB_B_SIZE	    _SB_MAKE64(40)
+#define M_DMA_DSCRB_B_SIZE	    _SB_MAKEMASK(9, S_DMA_DSCRB_B_SIZE)
+#define V_DMA_DSCRB_B_SIZE(x)	    _SB_MAKEVALUE(x, S_DMA_DSCRB_B_SIZE)
+#define G_DMA_DSCRB_B_SIZE(x)	    _SB_GETVALUE(x, S_DMA_DSCRB_B_SIZE, M_DMA_DSCRB_B_SIZE)
+
+#define M_DMA_DSCRB_B_VALID	    _SB_MAKEMASK1(49)
+
+#if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define S_DMA_DSCRB_PKT_SIZE_MSB    _SB_MAKE64(48)
+#define M_DMA_DSCRB_PKT_SIZE_MSB    _SB_MAKEMASK(2, S_DMA_DSCRB_PKT_SIZE_MSB)
+#define V_DMA_DSCRB_PKT_SIZE_MSB(x) _SB_MAKEVALUE(x, S_DMA_DSCRB_PKT_SIZE_MSB)
+#define G_DMA_DSCRB_PKT_SIZE_MSB(x) _SB_GETVALUE(x, S_DMA_DSCRB_PKT_SIZE_MSB, M_DMA_DSCRB_PKT_SIZE_MSB)
+#endif /* 1250 PASS3 || 112x PASS1 || 1480 */
+
+#define S_DMA_DSCRB_PKT_SIZE	    _SB_MAKE64(50)
+#define M_DMA_DSCRB_PKT_SIZE	    _SB_MAKEMASK(14, S_DMA_DSCRB_PKT_SIZE)
+#define V_DMA_DSCRB_PKT_SIZE(x)	    _SB_MAKEVALUE(x, S_DMA_DSCRB_PKT_SIZE)
+#define G_DMA_DSCRB_PKT_SIZE(x)	    _SB_GETVALUE(x, S_DMA_DSCRB_PKT_SIZE, M_DMA_DSCRB_PKT_SIZE)
+
+/*
+ * from pass2 some bits in dscr_b are also used for rx status
+ */
+#define S_DMA_DSCRB_STATUS	    _SB_MAKE64(0)
+#define M_DMA_DSCRB_STATUS	    _SB_MAKEMASK(1, S_DMA_DSCRB_STATUS)
+#define V_DMA_DSCRB_STATUS(x)	    _SB_MAKEVALUE(x, S_DMA_DSCRB_STATUS)
+#define G_DMA_DSCRB_STATUS(x)	    _SB_GETVALUE(x, S_DMA_DSCRB_STATUS, M_DMA_DSCRB_STATUS)
+
+/*
+ * Ethernet Descriptor Status Bits (Table 7-15)
+ */
+
+#define M_DMA_ETHRX_BADIP4CS	    _SB_MAKEMASK1(51)
+#define M_DMA_ETHRX_DSCRERR	    _SB_MAKEMASK1(52)
+
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+/* Note: This bit is in the DSCR_B options field */
+#define M_DMA_ETHRX_BADTCPCS	_SB_MAKEMASK1(0)
+#endif /* 1250 PASS2 || 112x PASS1 || 1480 */
+
+#if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+/* Note: These bits are in the DSCR_B options field */
+#define M_DMA_ETH_VLAN_FLAG	_SB_MAKEMASK1(1)
+#define M_DMA_ETH_CRC_FLAG	_SB_MAKEMASK1(2)
+#endif /* 1250 PASS3 || 112x PASS1 || 1480 */
+
+#define S_DMA_ETHRX_RXCH	    53
+#define M_DMA_ETHRX_RXCH	    _SB_MAKEMASK(2, S_DMA_ETHRX_RXCH)
+#define V_DMA_ETHRX_RXCH(x)	    _SB_MAKEVALUE(x, S_DMA_ETHRX_RXCH)
+#define G_DMA_ETHRX_RXCH(x)	    _SB_GETVALUE(x, S_DMA_ETHRX_RXCH, M_DMA_ETHRX_RXCH)
+
+#define S_DMA_ETHRX_PKTTYPE	    55
+#define M_DMA_ETHRX_PKTTYPE	    _SB_MAKEMASK(3, S_DMA_ETHRX_PKTTYPE)
+#define V_DMA_ETHRX_PKTTYPE(x)	    _SB_MAKEVALUE(x, S_DMA_ETHRX_PKTTYPE)
+#define G_DMA_ETHRX_PKTTYPE(x)	    _SB_GETVALUE(x, S_DMA_ETHRX_PKTTYPE, M_DMA_ETHRX_PKTTYPE)
+
+#define K_DMA_ETHRX_PKTTYPE_IPV4    0
+#define K_DMA_ETHRX_PKTTYPE_ARPV4   1
+#define K_DMA_ETHRX_PKTTYPE_802	    2
+#define K_DMA_ETHRX_PKTTYPE_OTHER   3
+#define K_DMA_ETHRX_PKTTYPE_USER0   4
+#define K_DMA_ETHRX_PKTTYPE_USER1   5
+#define K_DMA_ETHRX_PKTTYPE_USER2   6
+#define K_DMA_ETHRX_PKTTYPE_USER3   7
+
+#define M_DMA_ETHRX_MATCH_HASH	    _SB_MAKEMASK1(58)
+#define M_DMA_ETHRX_MATCH_EXACT	    _SB_MAKEMASK1(59)
+#define M_DMA_ETHRX_BCAST	    _SB_MAKEMASK1(60)
+#define M_DMA_ETHRX_MCAST	    _SB_MAKEMASK1(61)
+#define M_DMA_ETHRX_BAD		    _SB_MAKEMASK1(62)
+#define M_DMA_ETHRX_SOP		    _SB_MAKEMASK1(63)
+
+/*
+ * Ethernet Transmit Status Bits (Table 7-16)
+ */
+
+#define M_DMA_ETHTX_SOP		    _SB_MAKEMASK1(63)
+
+/*
+ * Ethernet Transmit Options (Table 7-17)
+ */
+
+#define K_DMA_ETHTX_NOTSOP	    _SB_MAKE64(0x00)
+#define K_DMA_ETHTX_APPENDCRC	    _SB_MAKE64(0x01)
+#define K_DMA_ETHTX_REPLACECRC	    _SB_MAKE64(0x02)
+#define K_DMA_ETHTX_APPENDCRC_APPENDPAD _SB_MAKE64(0x03)
+#define K_DMA_ETHTX_APPENDVLAN_REPLACECRC _SB_MAKE64(0x04)
+#define K_DMA_ETHTX_REMOVEVLAN_REPLACECRC _SB_MAKE64(0x05)
+#define K_DMA_ETHTX_REPLACEVLAN_REPLACECRC _SB_MAKE64(0x6)
+#define K_DMA_ETHTX_NOMODS	    _SB_MAKE64(0x07)
+#define K_DMA_ETHTX_RESERVED1	    _SB_MAKE64(0x08)
+#define K_DMA_ETHTX_REPLACESADDR_APPENDCRC _SB_MAKE64(0x09)
+#define K_DMA_ETHTX_REPLACESADDR_REPLACECRC _SB_MAKE64(0x0A)
+#define K_DMA_ETHTX_REPLACESADDR_APPENDCRC_APPENDPAD _SB_MAKE64(0x0B)
+#define K_DMA_ETHTX_REPLACESADDR_APPENDVLAN_REPLACECRC _SB_MAKE64(0x0C)
+#define K_DMA_ETHTX_REPLACESADDR_REMOVEVLAN_REPLACECRC _SB_MAKE64(0x0D)
+#define K_DMA_ETHTX_REPLACESADDR_REPLACEVLAN_REPLACECRC _SB_MAKE64(0x0E)
+#define K_DMA_ETHTX_RESERVED2	    _SB_MAKE64(0x0F)
+
+/*
+ * Serial Receive Options (Table 7-18)
+ */
+#define M_DMA_SERRX_CRC_ERROR	    _SB_MAKEMASK1(56)
+#define M_DMA_SERRX_ABORT	    _SB_MAKEMASK1(57)
+#define M_DMA_SERRX_OCTET_ERROR	    _SB_MAKEMASK1(58)
+#define M_DMA_SERRX_LONGFRAME_ERROR _SB_MAKEMASK1(59)
+#define M_DMA_SERRX_SHORTFRAME_ERROR _SB_MAKEMASK1(60)
+#define M_DMA_SERRX_OVERRUN_ERROR   _SB_MAKEMASK1(61)
+#define M_DMA_SERRX_GOOD	    _SB_MAKEMASK1(62)
+#define M_DMA_SERRX_SOP		    _SB_MAKEMASK1(63)
+
+/*
+ * Serial Transmit Status Bits (Table 7-20)
+ */
+
+#define M_DMA_SERTX_FLAG	    _SB_MAKEMASK1(63)
+
+/*
+ * Serial Transmit Options (Table 7-21)
+ */
+
+#define K_DMA_SERTX_RESERVED	    _SB_MAKEMASK1(0)
+#define K_DMA_SERTX_APPENDCRC	    _SB_MAKEMASK1(1)
+#define K_DMA_SERTX_APPENDPAD	    _SB_MAKEMASK1(2)
+#define K_DMA_SERTX_ABORT	    _SB_MAKEMASK1(3)
+
+
+/*  *********************************************************************
+    *  Data Mover Registers
+    ********************************************************************* */
+
+/*
+ * Data Mover Descriptor Base Address Register (Table 7-22)
+ * Register: DM_DSCR_BASE_0
+ * Register: DM_DSCR_BASE_1
+ * Register: DM_DSCR_BASE_2
+ * Register: DM_DSCR_BASE_3
+ */
+
+#define M_DM_DSCR_BASE_MBZ	    _SB_MAKEMASK(4, 0)
+
+/*  Note: Just mask the base address and then OR it in. */
+#define S_DM_DSCR_BASE_ADDR	    _SB_MAKE64(4)
+#define M_DM_DSCR_BASE_ADDR	    _SB_MAKEMASK(36, S_DM_DSCR_BASE_ADDR)
+
+#define S_DM_DSCR_BASE_RINGSZ	    _SB_MAKE64(40)
+#define M_DM_DSCR_BASE_RINGSZ	    _SB_MAKEMASK(16, S_DM_DSCR_BASE_RINGSZ)
+#define V_DM_DSCR_BASE_RINGSZ(x)    _SB_MAKEVALUE(x, S_DM_DSCR_BASE_RINGSZ)
+#define G_DM_DSCR_BASE_RINGSZ(x)    _SB_GETVALUE(x, S_DM_DSCR_BASE_RINGSZ, M_DM_DSCR_BASE_RINGSZ)
+
+#define S_DM_DSCR_BASE_PRIORITY	    _SB_MAKE64(56)
+#define M_DM_DSCR_BASE_PRIORITY	    _SB_MAKEMASK(3, S_DM_DSCR_BASE_PRIORITY)
+#define V_DM_DSCR_BASE_PRIORITY(x)  _SB_MAKEVALUE(x, S_DM_DSCR_BASE_PRIORITY)
+#define G_DM_DSCR_BASE_PRIORITY(x)  _SB_GETVALUE(x, S_DM_DSCR_BASE_PRIORITY, M_DM_DSCR_BASE_PRIORITY)
+
+#define K_DM_DSCR_BASE_PRIORITY_1   0
+#define K_DM_DSCR_BASE_PRIORITY_2   1
+#define K_DM_DSCR_BASE_PRIORITY_4   2
+#define K_DM_DSCR_BASE_PRIORITY_8   3
+#define K_DM_DSCR_BASE_PRIORITY_16  4
+
+#define M_DM_DSCR_BASE_ACTIVE	    _SB_MAKEMASK1(59)
+#define M_DM_DSCR_BASE_INTERRUPT    _SB_MAKEMASK1(60)
+#define M_DM_DSCR_BASE_RESET	    _SB_MAKEMASK1(61)	/* write register */
+#define M_DM_DSCR_BASE_ERROR	    _SB_MAKEMASK1(61)	/* read register */
+#define M_DM_DSCR_BASE_ABORT	    _SB_MAKEMASK1(62)
+#define M_DM_DSCR_BASE_ENABL	    _SB_MAKEMASK1(63)
+
+/*
+ * Data Mover Descriptor Count Register (Table 7-25)
+ */
+
+/* no bitfields */
+
+/*
+ * Data Mover Current Descriptor Address (Table 7-24)
+ * Register: DM_CUR_DSCR_ADDR_0
+ * Register: DM_CUR_DSCR_ADDR_1
+ * Register: DM_CUR_DSCR_ADDR_2
+ * Register: DM_CUR_DSCR_ADDR_3
+ */
+
+#define S_DM_CUR_DSCR_DSCR_ADDR	    _SB_MAKE64(0)
+#define M_DM_CUR_DSCR_DSCR_ADDR	    _SB_MAKEMASK(40, S_DM_CUR_DSCR_DSCR_ADDR)
+
+#define S_DM_CUR_DSCR_DSCR_COUNT    _SB_MAKE64(48)
+#define M_DM_CUR_DSCR_DSCR_COUNT    _SB_MAKEMASK(16, S_DM_CUR_DSCR_DSCR_COUNT)
+#define V_DM_CUR_DSCR_DSCR_COUNT(r) _SB_MAKEVALUE(r, S_DM_CUR_DSCR_DSCR_COUNT)
+#define G_DM_CUR_DSCR_DSCR_COUNT(r) _SB_GETVALUE(r, S_DM_CUR_DSCR_DSCR_COUNT,\
+				     M_DM_CUR_DSCR_DSCR_COUNT)
+
+
+#if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+/*
+ * Data Mover Channel Partial Result Registers
+ * Register: DM_PARTIAL_0
+ * Register: DM_PARTIAL_1
+ * Register: DM_PARTIAL_2
+ * Register: DM_PARTIAL_3
+ */
+#define S_DM_PARTIAL_CRC_PARTIAL      _SB_MAKE64(0)
+#define M_DM_PARTIAL_CRC_PARTIAL      _SB_MAKEMASK(32, S_DM_PARTIAL_CRC_PARTIAL)
+#define V_DM_PARTIAL_CRC_PARTIAL(r)   _SB_MAKEVALUE(r, S_DM_PARTIAL_CRC_PARTIAL)
+#define G_DM_PARTIAL_CRC_PARTIAL(r)   _SB_GETVALUE(r, S_DM_PARTIAL_CRC_PARTIAL,\
+				       M_DM_PARTIAL_CRC_PARTIAL)
+
+#define S_DM_PARTIAL_TCPCS_PARTIAL    _SB_MAKE64(32)
+#define M_DM_PARTIAL_TCPCS_PARTIAL    _SB_MAKEMASK(16, S_DM_PARTIAL_TCPCS_PARTIAL)
+#define V_DM_PARTIAL_TCPCS_PARTIAL(r) _SB_MAKEVALUE(r, S_DM_PARTIAL_TCPCS_PARTIAL)
+#define G_DM_PARTIAL_TCPCS_PARTIAL(r) _SB_GETVALUE(r, S_DM_PARTIAL_TCPCS_PARTIAL,\
+				       M_DM_PARTIAL_TCPCS_PARTIAL)
+
+#define M_DM_PARTIAL_ODD_BYTE	      _SB_MAKEMASK1(48)
+#endif /* 1250 PASS3 || 112x PASS1 || 1480 */
+
+
+#if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+/*
+ * Data Mover CRC Definition Registers
+ * Register: CRC_DEF_0
+ * Register: CRC_DEF_1
+ */
+#define S_CRC_DEF_CRC_INIT	      _SB_MAKE64(0)
+#define M_CRC_DEF_CRC_INIT	      _SB_MAKEMASK(32, S_CRC_DEF_CRC_INIT)
+#define V_CRC_DEF_CRC_INIT(r)	      _SB_MAKEVALUE(r, S_CRC_DEF_CRC_INIT)
+#define G_CRC_DEF_CRC_INIT(r)	      _SB_GETVALUE(r, S_CRC_DEF_CRC_INIT,\
+				       M_CRC_DEF_CRC_INIT)
+
+#define S_CRC_DEF_CRC_POLY	      _SB_MAKE64(32)
+#define M_CRC_DEF_CRC_POLY	      _SB_MAKEMASK(32, S_CRC_DEF_CRC_POLY)
+#define V_CRC_DEF_CRC_POLY(r)	      _SB_MAKEVALUE(r, S_CRC_DEF_CRC_POLY)
+#define G_CRC_DEF_CRC_POLY(r)	      _SB_GETVALUE(r, S_CRC_DEF_CRC_POLY,\
+				       M_CRC_DEF_CRC_POLY)
+#endif /* 1250 PASS3 || 112x PASS1 || 1480 */
+
+
+#if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+/*
+ * Data Mover CRC/Checksum Definition Registers
+ * Register: CTCP_DEF_0
+ * Register: CTCP_DEF_1
+ */
+#define S_CTCP_DEF_CRC_TXOR	      _SB_MAKE64(0)
+#define M_CTCP_DEF_CRC_TXOR	      _SB_MAKEMASK(32, S_CTCP_DEF_CRC_TXOR)
+#define V_CTCP_DEF_CRC_TXOR(r)	      _SB_MAKEVALUE(r, S_CTCP_DEF_CRC_TXOR)
+#define G_CTCP_DEF_CRC_TXOR(r)	      _SB_GETVALUE(r, S_CTCP_DEF_CRC_TXOR,\
+				       M_CTCP_DEF_CRC_TXOR)
+
+#define S_CTCP_DEF_TCPCS_INIT	      _SB_MAKE64(32)
+#define M_CTCP_DEF_TCPCS_INIT	      _SB_MAKEMASK(16, S_CTCP_DEF_TCPCS_INIT)
+#define V_CTCP_DEF_TCPCS_INIT(r)      _SB_MAKEVALUE(r, S_CTCP_DEF_TCPCS_INIT)
+#define G_CTCP_DEF_TCPCS_INIT(r)      _SB_GETVALUE(r, S_CTCP_DEF_TCPCS_INIT,\
+				       M_CTCP_DEF_TCPCS_INIT)
+
+#define S_CTCP_DEF_CRC_WIDTH	      _SB_MAKE64(48)
+#define M_CTCP_DEF_CRC_WIDTH	      _SB_MAKEMASK(2, S_CTCP_DEF_CRC_WIDTH)
+#define V_CTCP_DEF_CRC_WIDTH(r)	      _SB_MAKEVALUE(r, S_CTCP_DEF_CRC_WIDTH)
+#define G_CTCP_DEF_CRC_WIDTH(r)	      _SB_GETVALUE(r, S_CTCP_DEF_CRC_WIDTH,\
+				       M_CTCP_DEF_CRC_WIDTH)
+
+#define K_CTCP_DEF_CRC_WIDTH_4	      0
+#define K_CTCP_DEF_CRC_WIDTH_2	      1
+#define K_CTCP_DEF_CRC_WIDTH_1	      2
+
+#define M_CTCP_DEF_CRC_BIT_ORDER      _SB_MAKEMASK1(50)
+#endif /* 1250 PASS3 || 112x PASS1 || 1480 */
+
+
+/*
+ * Data Mover Descriptor Doubleword "A"	 (Table 7-26)
+ */
+
+#define S_DM_DSCRA_DST_ADDR	    _SB_MAKE64(0)
+#define M_DM_DSCRA_DST_ADDR	    _SB_MAKEMASK(40, S_DM_DSCRA_DST_ADDR)
+
+#define M_DM_DSCRA_UN_DEST	    _SB_MAKEMASK1(40)
+#define M_DM_DSCRA_UN_SRC	    _SB_MAKEMASK1(41)
+#define M_DM_DSCRA_INTERRUPT	    _SB_MAKEMASK1(42)
+#if SIBYTE_HDR_FEATURE_UP_TO(1250, PASS1)
+#define M_DM_DSCRA_THROTTLE	    _SB_MAKEMASK1(43)
+#endif /* up to 1250 PASS1 */
+
+#define S_DM_DSCRA_DIR_DEST	    _SB_MAKE64(44)
+#define M_DM_DSCRA_DIR_DEST	    _SB_MAKEMASK(2, S_DM_DSCRA_DIR_DEST)
+#define V_DM_DSCRA_DIR_DEST(x)	    _SB_MAKEVALUE(x, S_DM_DSCRA_DIR_DEST)
+#define G_DM_DSCRA_DIR_DEST(x)	    _SB_GETVALUE(x, S_DM_DSCRA_DIR_DEST, M_DM_DSCRA_DIR_DEST)
+
+#define K_DM_DSCRA_DIR_DEST_INCR    0
+#define K_DM_DSCRA_DIR_DEST_DECR    1
+#define K_DM_DSCRA_DIR_DEST_CONST   2
+
+#define V_DM_DSCRA_DIR_DEST_INCR    _SB_MAKEVALUE(K_DM_DSCRA_DIR_DEST_INCR, S_DM_DSCRA_DIR_DEST)
+#define V_DM_DSCRA_DIR_DEST_DECR    _SB_MAKEVALUE(K_DM_DSCRA_DIR_DEST_DECR, S_DM_DSCRA_DIR_DEST)
+#define V_DM_DSCRA_DIR_DEST_CONST   _SB_MAKEVALUE(K_DM_DSCRA_DIR_DEST_CONST, S_DM_DSCRA_DIR_DEST)
+
+#define S_DM_DSCRA_DIR_SRC	    _SB_MAKE64(46)
+#define M_DM_DSCRA_DIR_SRC	    _SB_MAKEMASK(2, S_DM_DSCRA_DIR_SRC)
+#define V_DM_DSCRA_DIR_SRC(x)	    _SB_MAKEVALUE(x, S_DM_DSCRA_DIR_SRC)
+#define G_DM_DSCRA_DIR_SRC(x)	    _SB_GETVALUE(x, S_DM_DSCRA_DIR_SRC, M_DM_DSCRA_DIR_SRC)
+
+#define K_DM_DSCRA_DIR_SRC_INCR	    0
+#define K_DM_DSCRA_DIR_SRC_DECR	    1
+#define K_DM_DSCRA_DIR_SRC_CONST    2
+
+#define V_DM_DSCRA_DIR_SRC_INCR	    _SB_MAKEVALUE(K_DM_DSCRA_DIR_SRC_INCR, S_DM_DSCRA_DIR_SRC)
+#define V_DM_DSCRA_DIR_SRC_DECR	    _SB_MAKEVALUE(K_DM_DSCRA_DIR_SRC_DECR, S_DM_DSCRA_DIR_SRC)
+#define V_DM_DSCRA_DIR_SRC_CONST    _SB_MAKEVALUE(K_DM_DSCRA_DIR_SRC_CONST, S_DM_DSCRA_DIR_SRC)
+
+
+#define M_DM_DSCRA_ZERO_MEM	    _SB_MAKEMASK1(48)
+#define M_DM_DSCRA_PREFETCH	    _SB_MAKEMASK1(49)
+#define M_DM_DSCRA_L2C_DEST	    _SB_MAKEMASK1(50)
+#define M_DM_DSCRA_L2C_SRC	    _SB_MAKEMASK1(51)
+
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define M_DM_DSCRA_RD_BKOFF	    _SB_MAKEMASK1(52)
+#define M_DM_DSCRA_WR_BKOFF	    _SB_MAKEMASK1(53)
+#endif /* 1250 PASS2 || 112x PASS1 || 1480 */
+
+#if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define M_DM_DSCRA_TCPCS_EN	    _SB_MAKEMASK1(54)
+#define M_DM_DSCRA_TCPCS_RES	    _SB_MAKEMASK1(55)
+#define M_DM_DSCRA_TCPCS_AP	    _SB_MAKEMASK1(56)
+#define M_DM_DSCRA_CRC_EN	    _SB_MAKEMASK1(57)
+#define M_DM_DSCRA_CRC_RES	    _SB_MAKEMASK1(58)
+#define M_DM_DSCRA_CRC_AP	    _SB_MAKEMASK1(59)
+#define M_DM_DSCRA_CRC_DFN	    _SB_MAKEMASK1(60)
+#define M_DM_DSCRA_CRC_XBIT	    _SB_MAKEMASK1(61)
+#endif /* 1250 PASS3 || 112x PASS1 || 1480 */
+
+#define M_DM_DSCRA_RESERVED2	    _SB_MAKEMASK(3, 61)
+
+/*
+ * Data Mover Descriptor Doubleword "B"	 (Table 7-25)
+ */
+
+#define S_DM_DSCRB_SRC_ADDR	    _SB_MAKE64(0)
+#define M_DM_DSCRB_SRC_ADDR	    _SB_MAKEMASK(40, S_DM_DSCRB_SRC_ADDR)
+
+#define S_DM_DSCRB_SRC_LENGTH	    _SB_MAKE64(40)
+#define M_DM_DSCRB_SRC_LENGTH	    _SB_MAKEMASK(20, S_DM_DSCRB_SRC_LENGTH)
+#define V_DM_DSCRB_SRC_LENGTH(x)    _SB_MAKEVALUE(x, S_DM_DSCRB_SRC_LENGTH)
+#define G_DM_DSCRB_SRC_LENGTH(x)    _SB_GETVALUE(x, S_DM_DSCRB_SRC_LENGTH, M_DM_DSCRB_SRC_LENGTH)
+
+
+#endif
diff --git a/arch/mips/include/asm/sibyte/sb1250_genbus.h b/arch/mips/include/asm/sibyte/sb1250_genbus.h
new file mode 100644
index 000000000..ddeb8edf5
--- /dev/null
+++ b/arch/mips/include/asm/sibyte/sb1250_genbus.h
@@ -0,0 +1,461 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*  *********************************************************************
+    *  SB1250 Board Support Package
+    *
+    *  Generic Bus Constants			 File: sb1250_genbus.h
+    *
+    *  This module contains constants and macros useful for
+    *  manipulating the SB1250's Generic Bus interface
+    *
+    *  SB1250 specification level:  User's manual 10/21/02
+    *  BCM1280 specification level: User's Manual 11/14/03
+    *
+    *********************************************************************
+    *
+    *  Copyright 2000, 2001, 2002, 2003
+    *  Broadcom Corporation. All rights reserved.
+    *
+    ********************************************************************* */
+
+
+#ifndef _SB1250_GENBUS_H
+#define _SB1250_GENBUS_H
+
+#include <asm/sibyte/sb1250_defs.h>
+
+/*
+ * Generic Bus Region Configuration Registers (Table 11-4)
+ */
+
+#define S_IO_RDY_ACTIVE		0
+#define M_IO_RDY_ACTIVE		_SB_MAKEMASK1(S_IO_RDY_ACTIVE)
+
+#define S_IO_ENA_RDY		1
+#define M_IO_ENA_RDY		_SB_MAKEMASK1(S_IO_ENA_RDY)
+
+#define S_IO_WIDTH_SEL		2
+#define M_IO_WIDTH_SEL		_SB_MAKEMASK(2, S_IO_WIDTH_SEL)
+#define K_IO_WIDTH_SEL_1	0
+#define K_IO_WIDTH_SEL_2	1
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1) \
+    || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define K_IO_WIDTH_SEL_1L	2
+#endif /* 1250 PASS2 || 112x PASS1 || 1480 */
+#define K_IO_WIDTH_SEL_4	3
+#define V_IO_WIDTH_SEL(x)	_SB_MAKEVALUE(x, S_IO_WIDTH_SEL)
+#define G_IO_WIDTH_SEL(x)	_SB_GETVALUE(x, S_IO_WIDTH_SEL, M_IO_WIDTH_SEL)
+
+#define S_IO_PARITY_ENA		4
+#define M_IO_PARITY_ENA		_SB_MAKEMASK1(S_IO_PARITY_ENA)
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1) \
+    || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define S_IO_BURST_EN		5
+#define M_IO_BURST_EN		_SB_MAKEMASK1(S_IO_BURST_EN)
+#endif /* 1250 PASS2 || 112x PASS1 || 1480 */
+#define S_IO_PARITY_ODD		6
+#define M_IO_PARITY_ODD		_SB_MAKEMASK1(S_IO_PARITY_ODD)
+#define S_IO_NONMUX		7
+#define M_IO_NONMUX		_SB_MAKEMASK1(S_IO_NONMUX)
+
+#define S_IO_TIMEOUT		8
+#define M_IO_TIMEOUT		_SB_MAKEMASK(8, S_IO_TIMEOUT)
+#define V_IO_TIMEOUT(x)		_SB_MAKEVALUE(x, S_IO_TIMEOUT)
+#define G_IO_TIMEOUT(x)		_SB_GETVALUE(x, S_IO_TIMEOUT, M_IO_TIMEOUT)
+
+/*
+ * Generic Bus Region Size register (Table 11-5)
+ */
+
+#define S_IO_MULT_SIZE		0
+#define M_IO_MULT_SIZE		_SB_MAKEMASK(12, S_IO_MULT_SIZE)
+#define V_IO_MULT_SIZE(x)	_SB_MAKEVALUE(x, S_IO_MULT_SIZE)
+#define G_IO_MULT_SIZE(x)	_SB_GETVALUE(x, S_IO_MULT_SIZE, M_IO_MULT_SIZE)
+
+#define S_IO_REGSIZE		16	 /* # bits to shift size for this reg */
+
+/*
+ * Generic Bus Region Address (Table 11-6)
+ */
+
+#define S_IO_START_ADDR		0
+#define M_IO_START_ADDR		_SB_MAKEMASK(14, S_IO_START_ADDR)
+#define V_IO_START_ADDR(x)	_SB_MAKEVALUE(x, S_IO_START_ADDR)
+#define G_IO_START_ADDR(x)	_SB_GETVALUE(x, S_IO_START_ADDR, M_IO_START_ADDR)
+
+#define S_IO_ADDRBASE		16	 /* # bits to shift addr for this reg */
+
+#define M_IO_BLK_CACHE		_SB_MAKEMASK1(15)
+
+
+/*
+ * Generic Bus Timing 0 Registers (Table 11-7)
+ */
+
+#define S_IO_ALE_WIDTH		0
+#define M_IO_ALE_WIDTH		_SB_MAKEMASK(3, S_IO_ALE_WIDTH)
+#define V_IO_ALE_WIDTH(x)	_SB_MAKEVALUE(x, S_IO_ALE_WIDTH)
+#define G_IO_ALE_WIDTH(x)	_SB_GETVALUE(x, S_IO_ALE_WIDTH, M_IO_ALE_WIDTH)
+
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1) \
+    || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define M_IO_EARLY_CS		_SB_MAKEMASK1(3)
+#endif /* 1250 PASS2 || 112x PASS1 || 1480 */
+
+#define S_IO_ALE_TO_CS		4
+#define M_IO_ALE_TO_CS		_SB_MAKEMASK(2, S_IO_ALE_TO_CS)
+#define V_IO_ALE_TO_CS(x)	_SB_MAKEVALUE(x, S_IO_ALE_TO_CS)
+#define G_IO_ALE_TO_CS(x)	_SB_GETVALUE(x, S_IO_ALE_TO_CS, M_IO_ALE_TO_CS)
+
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1) \
+    || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define S_IO_BURST_WIDTH	   _SB_MAKE64(6)
+#define M_IO_BURST_WIDTH	   _SB_MAKEMASK(2, S_IO_BURST_WIDTH)
+#define V_IO_BURST_WIDTH(x)	   _SB_MAKEVALUE(x, S_IO_BURST_WIDTH)
+#define G_IO_BURST_WIDTH(x)	   _SB_GETVALUE(x, S_IO_BURST_WIDTH, M_IO_BURST_WIDTH)
+#endif /* 1250 PASS2 || 112x PASS1 || 1480 */
+
+#define S_IO_CS_WIDTH		8
+#define M_IO_CS_WIDTH		_SB_MAKEMASK(5, S_IO_CS_WIDTH)
+#define V_IO_CS_WIDTH(x)	_SB_MAKEVALUE(x, S_IO_CS_WIDTH)
+#define G_IO_CS_WIDTH(x)	_SB_GETVALUE(x, S_IO_CS_WIDTH, M_IO_CS_WIDTH)
+
+#define S_IO_RDY_SMPLE		13
+#define M_IO_RDY_SMPLE		_SB_MAKEMASK(3, S_IO_RDY_SMPLE)
+#define V_IO_RDY_SMPLE(x)	_SB_MAKEVALUE(x, S_IO_RDY_SMPLE)
+#define G_IO_RDY_SMPLE(x)	_SB_GETVALUE(x, S_IO_RDY_SMPLE, M_IO_RDY_SMPLE)
+
+
+/*
+ * Generic Bus Timing 1 Registers (Table 11-8)
+ */
+
+#define S_IO_ALE_TO_WRITE	0
+#define M_IO_ALE_TO_WRITE	_SB_MAKEMASK(3, S_IO_ALE_TO_WRITE)
+#define V_IO_ALE_TO_WRITE(x)	_SB_MAKEVALUE(x, S_IO_ALE_TO_WRITE)
+#define G_IO_ALE_TO_WRITE(x)	_SB_GETVALUE(x, S_IO_ALE_TO_WRITE, M_IO_ALE_TO_WRITE)
+
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1) \
+    || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define M_IO_RDY_SYNC		_SB_MAKEMASK1(3)
+#endif /* 1250 PASS2 || 112x PASS1 || 1480 */
+
+#define S_IO_WRITE_WIDTH	4
+#define M_IO_WRITE_WIDTH	_SB_MAKEMASK(4, S_IO_WRITE_WIDTH)
+#define V_IO_WRITE_WIDTH(x)	_SB_MAKEVALUE(x, S_IO_WRITE_WIDTH)
+#define G_IO_WRITE_WIDTH(x)	_SB_GETVALUE(x, S_IO_WRITE_WIDTH, M_IO_WRITE_WIDTH)
+
+#define S_IO_IDLE_CYCLE		8
+#define M_IO_IDLE_CYCLE		_SB_MAKEMASK(4, S_IO_IDLE_CYCLE)
+#define V_IO_IDLE_CYCLE(x)	_SB_MAKEVALUE(x, S_IO_IDLE_CYCLE)
+#define G_IO_IDLE_CYCLE(x)	_SB_GETVALUE(x, S_IO_IDLE_CYCLE, M_IO_IDLE_CYCLE)
+
+#define S_IO_OE_TO_CS		12
+#define M_IO_OE_TO_CS		_SB_MAKEMASK(2, S_IO_OE_TO_CS)
+#define V_IO_OE_TO_CS(x)	_SB_MAKEVALUE(x, S_IO_OE_TO_CS)
+#define G_IO_OE_TO_CS(x)	_SB_GETVALUE(x, S_IO_OE_TO_CS, M_IO_OE_TO_CS)
+
+#define S_IO_CS_TO_OE		14
+#define M_IO_CS_TO_OE		_SB_MAKEMASK(2, S_IO_CS_TO_OE)
+#define V_IO_CS_TO_OE(x)	_SB_MAKEVALUE(x, S_IO_CS_TO_OE)
+#define G_IO_CS_TO_OE(x)	_SB_GETVALUE(x, S_IO_CS_TO_OE, M_IO_CS_TO_OE)
+
+/*
+ * Generic Bus Interrupt Status Register (Table 11-9)
+ */
+
+#define M_IO_CS_ERR_INT		_SB_MAKEMASK(0, 8)
+#define M_IO_CS0_ERR_INT	_SB_MAKEMASK1(0)
+#define M_IO_CS1_ERR_INT	_SB_MAKEMASK1(1)
+#define M_IO_CS2_ERR_INT	_SB_MAKEMASK1(2)
+#define M_IO_CS3_ERR_INT	_SB_MAKEMASK1(3)
+#define M_IO_CS4_ERR_INT	_SB_MAKEMASK1(4)
+#define M_IO_CS5_ERR_INT	_SB_MAKEMASK1(5)
+#define M_IO_CS6_ERR_INT	_SB_MAKEMASK1(6)
+#define M_IO_CS7_ERR_INT	_SB_MAKEMASK1(7)
+
+#define M_IO_RD_PAR_INT		_SB_MAKEMASK1(9)
+#define M_IO_TIMEOUT_INT	_SB_MAKEMASK1(10)
+#define M_IO_ILL_ADDR_INT	_SB_MAKEMASK1(11)
+#define M_IO_MULT_CS_INT	_SB_MAKEMASK1(12)
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define M_IO_COH_ERR		_SB_MAKEMASK1(14)
+#endif /* 1250 PASS2 || 112x PASS1 || 1480 */
+
+
+/*
+ * Generic Bus Output Drive Control Register 0 (Table 14-18)
+ */
+
+#define S_IO_SLEW0		0
+#define M_IO_SLEW0		_SB_MAKEMASK(2, S_IO_SLEW0)
+#define V_IO_SLEW0(x)		_SB_MAKEVALUE(x, S_IO_SLEW0)
+#define G_IO_SLEW0(x)		_SB_GETVALUE(x, S_IO_SLEW0, M_IO_SLEW0)
+
+#define S_IO_DRV_A		2
+#define M_IO_DRV_A		_SB_MAKEMASK(2, S_IO_DRV_A)
+#define V_IO_DRV_A(x)		_SB_MAKEVALUE(x, S_IO_DRV_A)
+#define G_IO_DRV_A(x)		_SB_GETVALUE(x, S_IO_DRV_A, M_IO_DRV_A)
+
+#define S_IO_DRV_B		6
+#define M_IO_DRV_B		_SB_MAKEMASK(2, S_IO_DRV_B)
+#define V_IO_DRV_B(x)		_SB_MAKEVALUE(x, S_IO_DRV_B)
+#define G_IO_DRV_B(x)		_SB_GETVALUE(x, S_IO_DRV_B, M_IO_DRV_B)
+
+#define S_IO_DRV_C		10
+#define M_IO_DRV_C		_SB_MAKEMASK(2, S_IO_DRV_C)
+#define V_IO_DRV_C(x)		_SB_MAKEVALUE(x, S_IO_DRV_C)
+#define G_IO_DRV_C(x)		_SB_GETVALUE(x, S_IO_DRV_C, M_IO_DRV_C)
+
+#define S_IO_DRV_D		14
+#define M_IO_DRV_D		_SB_MAKEMASK(2, S_IO_DRV_D)
+#define V_IO_DRV_D(x)		_SB_MAKEVALUE(x, S_IO_DRV_D)
+#define G_IO_DRV_D(x)		_SB_GETVALUE(x, S_IO_DRV_D, M_IO_DRV_D)
+
+/*
+ * Generic Bus Output Drive Control Register 1 (Table 14-19)
+ */
+
+#define S_IO_DRV_E		2
+#define M_IO_DRV_E		_SB_MAKEMASK(2, S_IO_DRV_E)
+#define V_IO_DRV_E(x)		_SB_MAKEVALUE(x, S_IO_DRV_E)
+#define G_IO_DRV_E(x)		_SB_GETVALUE(x, S_IO_DRV_E, M_IO_DRV_E)
+
+#define S_IO_DRV_F		6
+#define M_IO_DRV_F		_SB_MAKEMASK(2, S_IO_DRV_F)
+#define V_IO_DRV_F(x)		_SB_MAKEVALUE(x, S_IO_DRV_F)
+#define G_IO_DRV_F(x)		_SB_GETVALUE(x, S_IO_DRV_F, M_IO_DRV_F)
+
+#define S_IO_SLEW1		8
+#define M_IO_SLEW1		_SB_MAKEMASK(2, S_IO_SLEW1)
+#define V_IO_SLEW1(x)		_SB_MAKEVALUE(x, S_IO_SLEW1)
+#define G_IO_SLEW1(x)		_SB_GETVALUE(x, S_IO_SLEW1, M_IO_SLEW1)
+
+#define S_IO_DRV_G		10
+#define M_IO_DRV_G		_SB_MAKEMASK(2, S_IO_DRV_G)
+#define V_IO_DRV_G(x)		_SB_MAKEVALUE(x, S_IO_DRV_G)
+#define G_IO_DRV_G(x)		_SB_GETVALUE(x, S_IO_DRV_G, M_IO_DRV_G)
+
+#define S_IO_SLEW2		12
+#define M_IO_SLEW2		_SB_MAKEMASK(2, S_IO_SLEW2)
+#define V_IO_SLEW2(x)		_SB_MAKEVALUE(x, S_IO_SLEW2)
+#define G_IO_SLEW2(x)		_SB_GETVALUE(x, S_IO_SLEW2, M_IO_SLEW2)
+
+#define S_IO_DRV_H		14
+#define M_IO_DRV_H		_SB_MAKEMASK(2, S_IO_DRV_H)
+#define V_IO_DRV_H(x)		_SB_MAKEVALUE(x, S_IO_DRV_H)
+#define G_IO_DRV_H(x)		_SB_GETVALUE(x, S_IO_DRV_H, M_IO_DRV_H)
+
+/*
+ * Generic Bus Output Drive Control Register 2 (Table 14-20)
+ */
+
+#define S_IO_DRV_J		2
+#define M_IO_DRV_J		_SB_MAKEMASK(2, S_IO_DRV_J)
+#define V_IO_DRV_J(x)		_SB_MAKEVALUE(x, S_IO_DRV_J)
+#define G_IO_DRV_J(x)		_SB_GETVALUE(x, S_IO_DRV_J, M_IO_DRV_J)
+
+#define S_IO_DRV_K		6
+#define M_IO_DRV_K		_SB_MAKEMASK(2, S_IO_DRV_K)
+#define V_IO_DRV_K(x)		_SB_MAKEVALUE(x, S_IO_DRV_K)
+#define G_IO_DRV_K(x)		_SB_GETVALUE(x, S_IO_DRV_K, M_IO_DRV_K)
+
+#define S_IO_DRV_L		10
+#define M_IO_DRV_L		_SB_MAKEMASK(2, S_IO_DRV_L)
+#define V_IO_DRV_L(x)		_SB_MAKEVALUE(x, S_IO_DRV_L)
+#define G_IO_DRV_L(x)		_SB_GETVALUE(x, S_IO_DRV_L, M_IO_DRV_L)
+
+#define S_IO_DRV_M		14
+#define M_IO_DRV_M		_SB_MAKEMASK(2, S_IO_DRV_M)
+#define V_IO_DRV_M(x)		_SB_MAKEVALUE(x, S_IO_DRV_M)
+#define G_IO_DRV_M(x)		_SB_GETVALUE(x, S_IO_DRV_M, M_IO_DRV_M)
+
+/*
+ * Generic Bus Output Drive Control Register 3 (Table 14-21)
+ */
+
+#define S_IO_SLEW3		0
+#define M_IO_SLEW3		_SB_MAKEMASK(2, S_IO_SLEW3)
+#define V_IO_SLEW3(x)		_SB_MAKEVALUE(x, S_IO_SLEW3)
+#define G_IO_SLEW3(x)		_SB_GETVALUE(x, S_IO_SLEW3, M_IO_SLEW3)
+
+#define S_IO_DRV_N		2
+#define M_IO_DRV_N		_SB_MAKEMASK(2, S_IO_DRV_N)
+#define V_IO_DRV_N(x)		_SB_MAKEVALUE(x, S_IO_DRV_N)
+#define G_IO_DRV_N(x)		_SB_GETVALUE(x, S_IO_DRV_N, M_IO_DRV_N)
+
+#define S_IO_DRV_P		6
+#define M_IO_DRV_P		_SB_MAKEMASK(2, S_IO_DRV_P)
+#define V_IO_DRV_P(x)		_SB_MAKEVALUE(x, S_IO_DRV_P)
+#define G_IO_DRV_P(x)		_SB_GETVALUE(x, S_IO_DRV_P, M_IO_DRV_P)
+
+#define S_IO_DRV_Q		10
+#define M_IO_DRV_Q		_SB_MAKEMASK(2, S_IO_DRV_Q)
+#define V_IO_DRV_Q(x)		_SB_MAKEVALUE(x, S_IO_DRV_Q)
+#define G_IO_DRV_Q(x)		_SB_GETVALUE(x, S_IO_DRV_Q, M_IO_DRV_Q)
+
+#define S_IO_DRV_R		14
+#define M_IO_DRV_R		_SB_MAKEMASK(2, S_IO_DRV_R)
+#define V_IO_DRV_R(x)		_SB_MAKEVALUE(x, S_IO_DRV_R)
+#define G_IO_DRV_R(x)		_SB_GETVALUE(x, S_IO_DRV_R, M_IO_DRV_R)
+
+
+/*
+ * PCMCIA configuration register (Table 12-6)
+ */
+
+#define M_PCMCIA_CFG_ATTRMEM	_SB_MAKEMASK1(0)
+#define M_PCMCIA_CFG_3VEN	_SB_MAKEMASK1(1)
+#define M_PCMCIA_CFG_5VEN	_SB_MAKEMASK1(2)
+#define M_PCMCIA_CFG_VPPEN	_SB_MAKEMASK1(3)
+#define M_PCMCIA_CFG_RESET	_SB_MAKEMASK1(4)
+#define M_PCMCIA_CFG_APWRONEN	_SB_MAKEMASK1(5)
+#define M_PCMCIA_CFG_CDMASK	_SB_MAKEMASK1(6)
+#define M_PCMCIA_CFG_WPMASK	_SB_MAKEMASK1(7)
+#define M_PCMCIA_CFG_RDYMASK	_SB_MAKEMASK1(8)
+#define M_PCMCIA_CFG_PWRCTL	_SB_MAKEMASK1(9)
+
+#if SIBYTE_HDR_FEATURE_CHIP(1480)
+#define S_PCMCIA_MODE		16
+#define M_PCMCIA_MODE		_SB_MAKEMASK(3, S_PCMCIA_MODE)
+#define V_PCMCIA_MODE(x)	_SB_MAKEVALUE(x, S_PCMCIA_MODE)
+#define G_PCMCIA_MODE(x)	_SB_GETVALUE(x, S_PCMCIA_MODE, M_PCMCIA_MODE)
+
+#define K_PCMCIA_MODE_PCMA_NOB	0	/* standard PCMCIA "A", no "B" */
+#define K_PCMCIA_MODE_IDEA_NOB	1	/* IDE "A", no "B" */
+#define K_PCMCIA_MODE_PCMIOA_NOB 2	/* PCMCIA with I/O "A", no "B" */
+#define K_PCMCIA_MODE_PCMA_PCMB 4	/* standard PCMCIA "A", standard PCMCIA "B" */
+#define K_PCMCIA_MODE_IDEA_PCMB 5	/* IDE "A", standard PCMCIA "B" */
+#define K_PCMCIA_MODE_PCMA_IDEB 6	/* standard PCMCIA "A", IDE "B" */
+#define K_PCMCIA_MODE_IDEA_IDEB 7	/* IDE "A", IDE "B" */
+#endif
+
+
+/*
+ * PCMCIA status register (Table 12-7)
+ */
+
+#define M_PCMCIA_STATUS_CD1	_SB_MAKEMASK1(0)
+#define M_PCMCIA_STATUS_CD2	_SB_MAKEMASK1(1)
+#define M_PCMCIA_STATUS_VS1	_SB_MAKEMASK1(2)
+#define M_PCMCIA_STATUS_VS2	_SB_MAKEMASK1(3)
+#define M_PCMCIA_STATUS_WP	_SB_MAKEMASK1(4)
+#define M_PCMCIA_STATUS_RDY	_SB_MAKEMASK1(5)
+#define M_PCMCIA_STATUS_3VEN	_SB_MAKEMASK1(6)
+#define M_PCMCIA_STATUS_5VEN	_SB_MAKEMASK1(7)
+#define M_PCMCIA_STATUS_CDCHG	_SB_MAKEMASK1(8)
+#define M_PCMCIA_STATUS_WPCHG	_SB_MAKEMASK1(9)
+#define M_PCMCIA_STATUS_RDYCHG	_SB_MAKEMASK1(10)
+
+/*
+ * GPIO Interrupt Type Register (table 13-3)
+ */
+
+#define K_GPIO_INTR_DISABLE	0
+#define K_GPIO_INTR_EDGE	1
+#define K_GPIO_INTR_LEVEL	2
+#define K_GPIO_INTR_SPLIT	3
+
+#define S_GPIO_INTR_TYPEX(n)	(((n)/2)*2)
+#define M_GPIO_INTR_TYPEX(n)	_SB_MAKEMASK(2, S_GPIO_INTR_TYPEX(n))
+#define V_GPIO_INTR_TYPEX(n, x) _SB_MAKEVALUE(x, S_GPIO_INTR_TYPEX(n))
+#define G_GPIO_INTR_TYPEX(n, x) _SB_GETVALUE(x, S_GPIO_INTR_TYPEX(n), M_GPIO_INTR_TYPEX(n))
+
+#define S_GPIO_INTR_TYPE0	0
+#define M_GPIO_INTR_TYPE0	_SB_MAKEMASK(2, S_GPIO_INTR_TYPE0)
+#define V_GPIO_INTR_TYPE0(x)	_SB_MAKEVALUE(x, S_GPIO_INTR_TYPE0)
+#define G_GPIO_INTR_TYPE0(x)	_SB_GETVALUE(x, S_GPIO_INTR_TYPE0, M_GPIO_INTR_TYPE0)
+
+#define S_GPIO_INTR_TYPE2	2
+#define M_GPIO_INTR_TYPE2	_SB_MAKEMASK(2, S_GPIO_INTR_TYPE2)
+#define V_GPIO_INTR_TYPE2(x)	_SB_MAKEVALUE(x, S_GPIO_INTR_TYPE2)
+#define G_GPIO_INTR_TYPE2(x)	_SB_GETVALUE(x, S_GPIO_INTR_TYPE2, M_GPIO_INTR_TYPE2)
+
+#define S_GPIO_INTR_TYPE4	4
+#define M_GPIO_INTR_TYPE4	_SB_MAKEMASK(2, S_GPIO_INTR_TYPE4)
+#define V_GPIO_INTR_TYPE4(x)	_SB_MAKEVALUE(x, S_GPIO_INTR_TYPE4)
+#define G_GPIO_INTR_TYPE4(x)	_SB_GETVALUE(x, S_GPIO_INTR_TYPE4, M_GPIO_INTR_TYPE4)
+
+#define S_GPIO_INTR_TYPE6	6
+#define M_GPIO_INTR_TYPE6	_SB_MAKEMASK(2, S_GPIO_INTR_TYPE6)
+#define V_GPIO_INTR_TYPE6(x)	_SB_MAKEVALUE(x, S_GPIO_INTR_TYPE6)
+#define G_GPIO_INTR_TYPE6(x)	_SB_GETVALUE(x, S_GPIO_INTR_TYPE6, M_GPIO_INTR_TYPE6)
+
+#define S_GPIO_INTR_TYPE8	8
+#define M_GPIO_INTR_TYPE8	_SB_MAKEMASK(2, S_GPIO_INTR_TYPE8)
+#define V_GPIO_INTR_TYPE8(x)	_SB_MAKEVALUE(x, S_GPIO_INTR_TYPE8)
+#define G_GPIO_INTR_TYPE8(x)	_SB_GETVALUE(x, S_GPIO_INTR_TYPE8, M_GPIO_INTR_TYPE8)
+
+#define S_GPIO_INTR_TYPE10	10
+#define M_GPIO_INTR_TYPE10	_SB_MAKEMASK(2, S_GPIO_INTR_TYPE10)
+#define V_GPIO_INTR_TYPE10(x)	_SB_MAKEVALUE(x, S_GPIO_INTR_TYPE10)
+#define G_GPIO_INTR_TYPE10(x)	_SB_GETVALUE(x, S_GPIO_INTR_TYPE10, M_GPIO_INTR_TYPE10)
+
+#define S_GPIO_INTR_TYPE12	12
+#define M_GPIO_INTR_TYPE12	_SB_MAKEMASK(2, S_GPIO_INTR_TYPE12)
+#define V_GPIO_INTR_TYPE12(x)	_SB_MAKEVALUE(x, S_GPIO_INTR_TYPE12)
+#define G_GPIO_INTR_TYPE12(x)	_SB_GETVALUE(x, S_GPIO_INTR_TYPE12, M_GPIO_INTR_TYPE12)
+
+#define S_GPIO_INTR_TYPE14	14
+#define M_GPIO_INTR_TYPE14	_SB_MAKEMASK(2, S_GPIO_INTR_TYPE14)
+#define V_GPIO_INTR_TYPE14(x)	_SB_MAKEVALUE(x, S_GPIO_INTR_TYPE14)
+#define G_GPIO_INTR_TYPE14(x)	_SB_GETVALUE(x, S_GPIO_INTR_TYPE14, M_GPIO_INTR_TYPE14)
+
+#if SIBYTE_HDR_FEATURE_CHIP(1480)
+
+/*
+ * GPIO Interrupt Additional Type Register
+ */
+
+#define K_GPIO_INTR_BOTHEDGE	0
+#define K_GPIO_INTR_RISEEDGE	1
+#define K_GPIO_INTR_UNPRED1	2
+#define K_GPIO_INTR_UNPRED2	3
+
+#define S_GPIO_INTR_ATYPEX(n)	(((n)/2)*2)
+#define M_GPIO_INTR_ATYPEX(n)	_SB_MAKEMASK(2, S_GPIO_INTR_ATYPEX(n))
+#define V_GPIO_INTR_ATYPEX(n, x)	_SB_MAKEVALUE(x, S_GPIO_INTR_ATYPEX(n))
+#define G_GPIO_INTR_ATYPEX(n, x)	_SB_GETVALUE(x, S_GPIO_INTR_ATYPEX(n), M_GPIO_INTR_ATYPEX(n))
+
+#define S_GPIO_INTR_ATYPE0	0
+#define M_GPIO_INTR_ATYPE0	_SB_MAKEMASK(2, S_GPIO_INTR_ATYPE0)
+#define V_GPIO_INTR_ATYPE0(x)	_SB_MAKEVALUE(x, S_GPIO_INTR_ATYPE0)
+#define G_GPIO_INTR_ATYPE0(x)	_SB_GETVALUE(x, S_GPIO_INTR_ATYPE0, M_GPIO_INTR_ATYPE0)
+
+#define S_GPIO_INTR_ATYPE2	2
+#define M_GPIO_INTR_ATYPE2	_SB_MAKEMASK(2, S_GPIO_INTR_ATYPE2)
+#define V_GPIO_INTR_ATYPE2(x)	_SB_MAKEVALUE(x, S_GPIO_INTR_ATYPE2)
+#define G_GPIO_INTR_ATYPE2(x)	_SB_GETVALUE(x, S_GPIO_INTR_ATYPE2, M_GPIO_INTR_ATYPE2)
+
+#define S_GPIO_INTR_ATYPE4	4
+#define M_GPIO_INTR_ATYPE4	_SB_MAKEMASK(2, S_GPIO_INTR_ATYPE4)
+#define V_GPIO_INTR_ATYPE4(x)	_SB_MAKEVALUE(x, S_GPIO_INTR_ATYPE4)
+#define G_GPIO_INTR_ATYPE4(x)	_SB_GETVALUE(x, S_GPIO_INTR_ATYPE4, M_GPIO_INTR_ATYPE4)
+
+#define S_GPIO_INTR_ATYPE6	6
+#define M_GPIO_INTR_ATYPE6	_SB_MAKEMASK(2, S_GPIO_INTR_ATYPE6)
+#define V_GPIO_INTR_ATYPE6(x)	_SB_MAKEVALUE(x, S_GPIO_INTR_ATYPE6)
+#define G_GPIO_INTR_ATYPE6(x)	_SB_GETVALUE(x, S_GPIO_INTR_ATYPE6, M_GPIO_INTR_ATYPE6)
+
+#define S_GPIO_INTR_ATYPE8	8
+#define M_GPIO_INTR_ATYPE8	_SB_MAKEMASK(2, S_GPIO_INTR_ATYPE8)
+#define V_GPIO_INTR_ATYPE8(x)	_SB_MAKEVALUE(x, S_GPIO_INTR_ATYPE8)
+#define G_GPIO_INTR_ATYPE8(x)	_SB_GETVALUE(x, S_GPIO_INTR_ATYPE8, M_GPIO_INTR_ATYPE8)
+
+#define S_GPIO_INTR_ATYPE10	10
+#define M_GPIO_INTR_ATYPE10	_SB_MAKEMASK(2, S_GPIO_INTR_ATYPE10)
+#define V_GPIO_INTR_ATYPE10(x)	_SB_MAKEVALUE(x, S_GPIO_INTR_ATYPE10)
+#define G_GPIO_INTR_ATYPE10(x)	_SB_GETVALUE(x, S_GPIO_INTR_ATYPE10, M_GPIO_INTR_ATYPE10)
+
+#define S_GPIO_INTR_ATYPE12	12
+#define M_GPIO_INTR_ATYPE12	_SB_MAKEMASK(2, S_GPIO_INTR_ATYPE12)
+#define V_GPIO_INTR_ATYPE12(x)	_SB_MAKEVALUE(x, S_GPIO_INTR_ATYPE12)
+#define G_GPIO_INTR_ATYPE12(x)	_SB_GETVALUE(x, S_GPIO_INTR_ATYPE12, M_GPIO_INTR_ATYPE12)
+
+#define S_GPIO_INTR_ATYPE14	14
+#define M_GPIO_INTR_ATYPE14	_SB_MAKEMASK(2, S_GPIO_INTR_ATYPE14)
+#define V_GPIO_INTR_ATYPE14(x)	_SB_MAKEVALUE(x, S_GPIO_INTR_ATYPE14)
+#define G_GPIO_INTR_ATYPE14(x)	_SB_GETVALUE(x, S_GPIO_INTR_ATYPE14, M_GPIO_INTR_ATYPE14)
+#endif
+
+
+#endif
diff --git a/arch/mips/include/asm/sibyte/sb1250_int.h b/arch/mips/include/asm/sibyte/sb1250_int.h
new file mode 100644
index 000000000..2e0adb055
--- /dev/null
+++ b/arch/mips/include/asm/sibyte/sb1250_int.h
@@ -0,0 +1,235 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*  *********************************************************************
+    *  SB1250 Board Support Package
+    *
+    *  Interrupt Mapper definitions		File: sb1250_int.h
+    *
+    *  This module contains constants for manipulating the SB1250's
+    *  interrupt mapper and definitions for the interrupt sources.
+    *
+    *  SB1250 specification level:  User's manual 1/02/02
+    *
+    *********************************************************************
+    *
+    *  Copyright 2000, 2001, 2002, 2003
+    *  Broadcom Corporation. All rights reserved.
+    *
+    ********************************************************************* */
+
+
+#ifndef _SB1250_INT_H
+#define _SB1250_INT_H
+
+#include <asm/sibyte/sb1250_defs.h>
+
+/*  *********************************************************************
+    *  Interrupt Mapper Constants
+    ********************************************************************* */
+
+/*
+ * Interrupt sources (Table 4-8, UM 0.2)
+ *
+ * First, the interrupt numbers.
+ */
+
+#define K_INT_SOURCES		    64
+
+#define K_INT_WATCHDOG_TIMER_0	    0
+#define K_INT_WATCHDOG_TIMER_1	    1
+#define K_INT_TIMER_0		    2
+#define K_INT_TIMER_1		    3
+#define K_INT_TIMER_2		    4
+#define K_INT_TIMER_3		    5
+#define K_INT_SMB_0		    6
+#define K_INT_SMB_1		    7
+#define K_INT_UART_0		    8
+#define K_INT_UART_1		    9
+#define K_INT_SER_0		    10
+#define K_INT_SER_1		    11
+#define K_INT_PCMCIA		    12
+#define K_INT_ADDR_TRAP		    13
+#define K_INT_PERF_CNT		    14
+#define K_INT_TRACE_FREEZE	    15
+#define K_INT_BAD_ECC		    16
+#define K_INT_COR_ECC		    17
+#define K_INT_IO_BUS		    18
+#define K_INT_MAC_0		    19
+#define K_INT_MAC_1		    20
+#define K_INT_MAC_2		    21
+#define K_INT_DM_CH_0		    22
+#define K_INT_DM_CH_1		    23
+#define K_INT_DM_CH_2		    24
+#define K_INT_DM_CH_3		    25
+#define K_INT_MBOX_0		    26
+#define K_INT_MBOX_1		    27
+#define K_INT_MBOX_2		    28
+#define K_INT_MBOX_3		    29
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1)
+#define K_INT_CYCLE_CP0_INT	    30
+#define K_INT_CYCLE_CP1_INT	    31
+#endif /* 1250 PASS2 || 112x PASS1 */
+#define K_INT_GPIO_0		    32
+#define K_INT_GPIO_1		    33
+#define K_INT_GPIO_2		    34
+#define K_INT_GPIO_3		    35
+#define K_INT_GPIO_4		    36
+#define K_INT_GPIO_5		    37
+#define K_INT_GPIO_6		    38
+#define K_INT_GPIO_7		    39
+#define K_INT_GPIO_8		    40
+#define K_INT_GPIO_9		    41
+#define K_INT_GPIO_10		    42
+#define K_INT_GPIO_11		    43
+#define K_INT_GPIO_12		    44
+#define K_INT_GPIO_13		    45
+#define K_INT_GPIO_14		    46
+#define K_INT_GPIO_15		    47
+#define K_INT_LDT_FATAL		    48
+#define K_INT_LDT_NONFATAL	    49
+#define K_INT_LDT_SMI		    50
+#define K_INT_LDT_NMI		    51
+#define K_INT_LDT_INIT		    52
+#define K_INT_LDT_STARTUP	    53
+#define K_INT_LDT_EXT		    54
+#define K_INT_PCI_ERROR		    55
+#define K_INT_PCI_INTA		    56
+#define K_INT_PCI_INTB		    57
+#define K_INT_PCI_INTC		    58
+#define K_INT_PCI_INTD		    59
+#define K_INT_SPARE_2		    60
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1)
+#define K_INT_MAC_0_CH1		    61
+#define K_INT_MAC_1_CH1		    62
+#define K_INT_MAC_2_CH1		    63
+#endif /* 1250 PASS2 || 112x PASS1 */
+
+/*
+ * Mask values for each interrupt
+ */
+
+#define M_INT_WATCHDOG_TIMER_0	    _SB_MAKEMASK1(K_INT_WATCHDOG_TIMER_0)
+#define M_INT_WATCHDOG_TIMER_1	    _SB_MAKEMASK1(K_INT_WATCHDOG_TIMER_1)
+#define M_INT_TIMER_0		    _SB_MAKEMASK1(K_INT_TIMER_0)
+#define M_INT_TIMER_1		    _SB_MAKEMASK1(K_INT_TIMER_1)
+#define M_INT_TIMER_2		    _SB_MAKEMASK1(K_INT_TIMER_2)
+#define M_INT_TIMER_3		    _SB_MAKEMASK1(K_INT_TIMER_3)
+#define M_INT_SMB_0		    _SB_MAKEMASK1(K_INT_SMB_0)
+#define M_INT_SMB_1		    _SB_MAKEMASK1(K_INT_SMB_1)
+#define M_INT_UART_0		    _SB_MAKEMASK1(K_INT_UART_0)
+#define M_INT_UART_1		    _SB_MAKEMASK1(K_INT_UART_1)
+#define M_INT_SER_0		    _SB_MAKEMASK1(K_INT_SER_0)
+#define M_INT_SER_1		    _SB_MAKEMASK1(K_INT_SER_1)
+#define M_INT_PCMCIA		    _SB_MAKEMASK1(K_INT_PCMCIA)
+#define M_INT_ADDR_TRAP		    _SB_MAKEMASK1(K_INT_ADDR_TRAP)
+#define M_INT_PERF_CNT		    _SB_MAKEMASK1(K_INT_PERF_CNT)
+#define M_INT_TRACE_FREEZE	    _SB_MAKEMASK1(K_INT_TRACE_FREEZE)
+#define M_INT_BAD_ECC		    _SB_MAKEMASK1(K_INT_BAD_ECC)
+#define M_INT_COR_ECC		    _SB_MAKEMASK1(K_INT_COR_ECC)
+#define M_INT_IO_BUS		    _SB_MAKEMASK1(K_INT_IO_BUS)
+#define M_INT_MAC_0		    _SB_MAKEMASK1(K_INT_MAC_0)
+#define M_INT_MAC_1		    _SB_MAKEMASK1(K_INT_MAC_1)
+#define M_INT_MAC_2		    _SB_MAKEMASK1(K_INT_MAC_2)
+#define M_INT_DM_CH_0		    _SB_MAKEMASK1(K_INT_DM_CH_0)
+#define M_INT_DM_CH_1		    _SB_MAKEMASK1(K_INT_DM_CH_1)
+#define M_INT_DM_CH_2		    _SB_MAKEMASK1(K_INT_DM_CH_2)
+#define M_INT_DM_CH_3		    _SB_MAKEMASK1(K_INT_DM_CH_3)
+#define M_INT_MBOX_0		    _SB_MAKEMASK1(K_INT_MBOX_0)
+#define M_INT_MBOX_1		    _SB_MAKEMASK1(K_INT_MBOX_1)
+#define M_INT_MBOX_2		    _SB_MAKEMASK1(K_INT_MBOX_2)
+#define M_INT_MBOX_3		    _SB_MAKEMASK1(K_INT_MBOX_3)
+#define M_INT_MBOX_ALL		    _SB_MAKEMASK(4, K_INT_MBOX_0)
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1)
+#define M_INT_CYCLE_CP0_INT	    _SB_MAKEMASK1(K_INT_CYCLE_CP0_INT)
+#define M_INT_CYCLE_CP1_INT	    _SB_MAKEMASK1(K_INT_CYCLE_CP1_INT)
+#endif /* 1250 PASS2 || 112x PASS1 */
+#define M_INT_GPIO_0		    _SB_MAKEMASK1(K_INT_GPIO_0)
+#define M_INT_GPIO_1		    _SB_MAKEMASK1(K_INT_GPIO_1)
+#define M_INT_GPIO_2		    _SB_MAKEMASK1(K_INT_GPIO_2)
+#define M_INT_GPIO_3		    _SB_MAKEMASK1(K_INT_GPIO_3)
+#define M_INT_GPIO_4		    _SB_MAKEMASK1(K_INT_GPIO_4)
+#define M_INT_GPIO_5		    _SB_MAKEMASK1(K_INT_GPIO_5)
+#define M_INT_GPIO_6		    _SB_MAKEMASK1(K_INT_GPIO_6)
+#define M_INT_GPIO_7		    _SB_MAKEMASK1(K_INT_GPIO_7)
+#define M_INT_GPIO_8		    _SB_MAKEMASK1(K_INT_GPIO_8)
+#define M_INT_GPIO_9		    _SB_MAKEMASK1(K_INT_GPIO_9)
+#define M_INT_GPIO_10		    _SB_MAKEMASK1(K_INT_GPIO_10)
+#define M_INT_GPIO_11		    _SB_MAKEMASK1(K_INT_GPIO_11)
+#define M_INT_GPIO_12		    _SB_MAKEMASK1(K_INT_GPIO_12)
+#define M_INT_GPIO_13		    _SB_MAKEMASK1(K_INT_GPIO_13)
+#define M_INT_GPIO_14		    _SB_MAKEMASK1(K_INT_GPIO_14)
+#define M_INT_GPIO_15		    _SB_MAKEMASK1(K_INT_GPIO_15)
+#define M_INT_LDT_FATAL		    _SB_MAKEMASK1(K_INT_LDT_FATAL)
+#define M_INT_LDT_NONFATAL	    _SB_MAKEMASK1(K_INT_LDT_NONFATAL)
+#define M_INT_LDT_SMI		    _SB_MAKEMASK1(K_INT_LDT_SMI)
+#define M_INT_LDT_NMI		    _SB_MAKEMASK1(K_INT_LDT_NMI)
+#define M_INT_LDT_INIT		    _SB_MAKEMASK1(K_INT_LDT_INIT)
+#define M_INT_LDT_STARTUP	    _SB_MAKEMASK1(K_INT_LDT_STARTUP)
+#define M_INT_LDT_EXT		    _SB_MAKEMASK1(K_INT_LDT_EXT)
+#define M_INT_PCI_ERROR		    _SB_MAKEMASK1(K_INT_PCI_ERROR)
+#define M_INT_PCI_INTA		    _SB_MAKEMASK1(K_INT_PCI_INTA)
+#define M_INT_PCI_INTB		    _SB_MAKEMASK1(K_INT_PCI_INTB)
+#define M_INT_PCI_INTC		    _SB_MAKEMASK1(K_INT_PCI_INTC)
+#define M_INT_PCI_INTD		    _SB_MAKEMASK1(K_INT_PCI_INTD)
+#define M_INT_SPARE_2		    _SB_MAKEMASK1(K_INT_SPARE_2)
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1)
+#define M_INT_MAC_0_CH1		    _SB_MAKEMASK1(K_INT_MAC_0_CH1)
+#define M_INT_MAC_1_CH1		    _SB_MAKEMASK1(K_INT_MAC_1_CH1)
+#define M_INT_MAC_2_CH1		    _SB_MAKEMASK1(K_INT_MAC_2_CH1)
+#endif /* 1250 PASS2 || 112x PASS1 */
+
+/*
+ * Interrupt mappings
+ */
+
+#define K_INT_MAP_I0	0		/* interrupt pins on processor */
+#define K_INT_MAP_I1	1
+#define K_INT_MAP_I2	2
+#define K_INT_MAP_I3	3
+#define K_INT_MAP_I4	4
+#define K_INT_MAP_I5	5
+#define K_INT_MAP_NMI	6		/* nonmaskable */
+#define K_INT_MAP_DINT	7		/* debug interrupt */
+
+/*
+ * LDT Interrupt Set Register (table 4-5)
+ */
+
+#define S_INT_LDT_INTMSG	      0
+#define M_INT_LDT_INTMSG	      _SB_MAKEMASK(3, S_INT_LDT_INTMSG)
+#define V_INT_LDT_INTMSG(x)	      _SB_MAKEVALUE(x, S_INT_LDT_INTMSG)
+#define G_INT_LDT_INTMSG(x)	      _SB_GETVALUE(x, S_INT_LDT_INTMSG, M_INT_LDT_INTMSG)
+
+#define K_INT_LDT_INTMSG_FIXED	      0
+#define K_INT_LDT_INTMSG_ARBITRATED   1
+#define K_INT_LDT_INTMSG_SMI	      2
+#define K_INT_LDT_INTMSG_NMI	      3
+#define K_INT_LDT_INTMSG_INIT	      4
+#define K_INT_LDT_INTMSG_STARTUP      5
+#define K_INT_LDT_INTMSG_EXTINT	      6
+#define K_INT_LDT_INTMSG_RESERVED     7
+
+#define M_INT_LDT_EDGETRIGGER	      0
+#define M_INT_LDT_LEVELTRIGGER	      _SB_MAKEMASK1(3)
+
+#define M_INT_LDT_PHYSICALDEST	      0
+#define M_INT_LDT_LOGICALDEST	      _SB_MAKEMASK1(4)
+
+#define S_INT_LDT_INTDEST	      5
+#define M_INT_LDT_INTDEST	      _SB_MAKEMASK(10, S_INT_LDT_INTDEST)
+#define V_INT_LDT_INTDEST(x)	      _SB_MAKEVALUE(x, S_INT_LDT_INTDEST)
+#define G_INT_LDT_INTDEST(x)	      _SB_GETVALUE(x, S_INT_LDT_INTDEST, M_INT_LDT_INTDEST)
+
+#define S_INT_LDT_VECTOR	      13
+#define M_INT_LDT_VECTOR	      _SB_MAKEMASK(8, S_INT_LDT_VECTOR)
+#define V_INT_LDT_VECTOR(x)	      _SB_MAKEVALUE(x, S_INT_LDT_VECTOR)
+#define G_INT_LDT_VECTOR(x)	      _SB_GETVALUE(x, S_INT_LDT_VECTOR, M_INT_LDT_VECTOR)
+
+/*
+ * Vector format (Table 4-6)
+ */
+
+#define M_LDTVECT_RAISEINT		0x00
+#define M_LDTVECT_RAISEMBOX		0x40
+
+
+#endif	/* 1250/112x */
diff --git a/arch/mips/include/asm/sibyte/sb1250_l2c.h b/arch/mips/include/asm/sibyte/sb1250_l2c.h
new file mode 100644
index 000000000..cd8de844b
--- /dev/null
+++ b/arch/mips/include/asm/sibyte/sb1250_l2c.h
@@ -0,0 +1,118 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*  *********************************************************************
+    *  SB1250 Board Support Package
+    *
+    *  L2 Cache constants and macros		File: sb1250_l2c.h
+    *
+    *  This module contains constants useful for manipulating the
+    *  level 2 cache.
+    *
+    *  SB1250 specification level:  User's manual 1/02/02
+    *
+    *********************************************************************
+    *
+    *  Copyright 2000,2001,2002,2003
+    *  Broadcom Corporation. All rights reserved.
+    *
+    ********************************************************************* */
+
+
+#ifndef _SB1250_L2C_H
+#define _SB1250_L2C_H
+
+#include <asm/sibyte/sb1250_defs.h>
+
+/*
+ * Level 2 Cache Tag register (Table 5-3)
+ */
+
+#define S_L2C_TAG_MBZ		    0
+#define M_L2C_TAG_MBZ		    _SB_MAKEMASK(5, S_L2C_TAG_MBZ)
+
+#define S_L2C_TAG_INDEX		    5
+#define M_L2C_TAG_INDEX		    _SB_MAKEMASK(12, S_L2C_TAG_INDEX)
+#define V_L2C_TAG_INDEX(x)	    _SB_MAKEVALUE(x, S_L2C_TAG_INDEX)
+#define G_L2C_TAG_INDEX(x)	    _SB_GETVALUE(x, S_L2C_TAG_INDEX, M_L2C_TAG_INDEX)
+
+#define S_L2C_TAG_TAG		    17
+#define M_L2C_TAG_TAG		    _SB_MAKEMASK(23, S_L2C_TAG_TAG)
+#define V_L2C_TAG_TAG(x)	    _SB_MAKEVALUE(x, S_L2C_TAG_TAG)
+#define G_L2C_TAG_TAG(x)	    _SB_GETVALUE(x, S_L2C_TAG_TAG, M_L2C_TAG_TAG)
+
+#define S_L2C_TAG_ECC		    40
+#define M_L2C_TAG_ECC		    _SB_MAKEMASK(6, S_L2C_TAG_ECC)
+#define V_L2C_TAG_ECC(x)	    _SB_MAKEVALUE(x, S_L2C_TAG_ECC)
+#define G_L2C_TAG_ECC(x)	    _SB_GETVALUE(x, S_L2C_TAG_ECC, M_L2C_TAG_ECC)
+
+#define S_L2C_TAG_WAY		    46
+#define M_L2C_TAG_WAY		    _SB_MAKEMASK(2, S_L2C_TAG_WAY)
+#define V_L2C_TAG_WAY(x)	    _SB_MAKEVALUE(x, S_L2C_TAG_WAY)
+#define G_L2C_TAG_WAY(x)	    _SB_GETVALUE(x, S_L2C_TAG_WAY, M_L2C_TAG_WAY)
+
+#define M_L2C_TAG_DIRTY		    _SB_MAKEMASK1(48)
+#define M_L2C_TAG_VALID		    _SB_MAKEMASK1(49)
+
+/*
+ * Format of level 2 cache management address (table 5-2)
+ */
+
+#define S_L2C_MGMT_INDEX	    5
+#define M_L2C_MGMT_INDEX	    _SB_MAKEMASK(12, S_L2C_MGMT_INDEX)
+#define V_L2C_MGMT_INDEX(x)	    _SB_MAKEVALUE(x, S_L2C_MGMT_INDEX)
+#define G_L2C_MGMT_INDEX(x)	    _SB_GETVALUE(x, S_L2C_MGMT_INDEX, M_L2C_MGMT_INDEX)
+
+#define S_L2C_MGMT_QUADRANT	    15
+#define M_L2C_MGMT_QUADRANT	    _SB_MAKEMASK(2, S_L2C_MGMT_QUADRANT)
+#define V_L2C_MGMT_QUADRANT(x)	    _SB_MAKEVALUE(x, S_L2C_MGMT_QUADRANT)
+#define G_L2C_MGMT_QUADRANT(x)	    _SB_GETVALUE(x, S_L2C_MGMT_QUADRANT, M_L2C_MGMT_QUADRANT)
+
+#define S_L2C_MGMT_HALF		    16
+#define M_L2C_MGMT_HALF		    _SB_MAKEMASK(1, S_L2C_MGMT_HALF)
+
+#define S_L2C_MGMT_WAY		    17
+#define M_L2C_MGMT_WAY		    _SB_MAKEMASK(2, S_L2C_MGMT_WAY)
+#define V_L2C_MGMT_WAY(x)	    _SB_MAKEVALUE(x, S_L2C_MGMT_WAY)
+#define G_L2C_MGMT_WAY(x)	    _SB_GETVALUE(x, S_L2C_MGMT_WAY, M_L2C_MGMT_WAY)
+
+#define S_L2C_MGMT_ECC_DIAG	    21
+#define M_L2C_MGMT_ECC_DIAG	    _SB_MAKEMASK(2, S_L2C_MGMT_ECC_DIAG)
+#define V_L2C_MGMT_ECC_DIAG(x)	    _SB_MAKEVALUE(x, S_L2C_MGMT_ECC_DIAG)
+#define G_L2C_MGMT_ECC_DIAG(x)	    _SB_GETVALUE(x, S_L2C_MGMT_ECC_DIAG, M_L2C_MGMT_ECC_DIAG)
+
+#define S_L2C_MGMT_TAG		    23
+#define M_L2C_MGMT_TAG		    _SB_MAKEMASK(4, S_L2C_MGMT_TAG)
+#define V_L2C_MGMT_TAG(x)	    _SB_MAKEVALUE(x, S_L2C_MGMT_TAG)
+#define G_L2C_MGMT_TAG(x)	    _SB_GETVALUE(x, S_L2C_MGMT_TAG, M_L2C_MGMT_TAG)
+
+#define M_L2C_MGMT_DIRTY	    _SB_MAKEMASK1(19)
+#define M_L2C_MGMT_VALID	    _SB_MAKEMASK1(20)
+
+#define A_L2C_MGMT_TAG_BASE	    0x00D0000000
+
+#define L2C_ENTRIES_PER_WAY	  4096
+#define L2C_NUM_WAYS		  4
+
+
+#if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1)
+/*
+ * L2 Read Misc. register (A_L2_READ_MISC)
+ */
+#define S_L2C_MISC_NO_WAY		10
+#define M_L2C_MISC_NO_WAY		_SB_MAKEMASK(4, S_L2C_MISC_NO_WAY)
+#define V_L2C_MISC_NO_WAY(x)		_SB_MAKEVALUE(x, S_L2C_MISC_NO_WAY)
+#define G_L2C_MISC_NO_WAY(x)		_SB_GETVALUE(x, S_L2C_MISC_NO_WAY, M_L2C_MISC_NO_WAY)
+
+#define M_L2C_MISC_ECC_CLEANUP_DIS	_SB_MAKEMASK1(9)
+#define M_L2C_MISC_MC_PRIO_LOW		_SB_MAKEMASK1(8)
+#define M_L2C_MISC_SOFT_DISABLE_T	_SB_MAKEMASK1(7)
+#define M_L2C_MISC_SOFT_DISABLE_B	_SB_MAKEMASK1(6)
+#define M_L2C_MISC_SOFT_DISABLE_R	_SB_MAKEMASK1(5)
+#define M_L2C_MISC_SOFT_DISABLE_L	_SB_MAKEMASK1(4)
+#define M_L2C_MISC_SCACHE_DISABLE_T	_SB_MAKEMASK1(3)
+#define M_L2C_MISC_SCACHE_DISABLE_B	_SB_MAKEMASK1(2)
+#define M_L2C_MISC_SCACHE_DISABLE_R	_SB_MAKEMASK1(1)
+#define M_L2C_MISC_SCACHE_DISABLE_L	_SB_MAKEMASK1(0)
+#endif /* 1250 PASS3 || 112x PASS1 */
+
+
+#endif
diff --git a/arch/mips/include/asm/sibyte/sb1250_ldt.h b/arch/mips/include/asm/sibyte/sb1250_ldt.h
new file mode 100644
index 000000000..c22df8dbb
--- /dev/null
+++ b/arch/mips/include/asm/sibyte/sb1250_ldt.h
@@ -0,0 +1,409 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*  *********************************************************************
+    *  SB1250 Board Support Package
+    *
+    *  LDT constants				File: sb1250_ldt.h
+    *
+    *  This module contains constants and macros to describe
+    *  the LDT interface on the SB1250.
+    *
+    *  SB1250 specification level:  User's manual 1/02/02
+    *
+    *********************************************************************
+    *
+    *  Copyright 2000, 2001, 2002, 2003
+    *  Broadcom Corporation. All rights reserved.
+    *
+    ********************************************************************* */
+
+
+#ifndef _SB1250_LDT_H
+#define _SB1250_LDT_H
+
+#include <asm/sibyte/sb1250_defs.h>
+
+#define K_LDT_VENDOR_SIBYTE	0x166D
+#define K_LDT_DEVICE_SB1250	0x0002
+
+/*
+ * LDT Interface Type 1 (bridge) configuration header
+ */
+
+#define R_LDT_TYPE1_DEVICEID	0x0000
+#define R_LDT_TYPE1_CMDSTATUS	0x0004
+#define R_LDT_TYPE1_CLASSREV	0x0008
+#define R_LDT_TYPE1_DEVHDR	0x000C
+#define R_LDT_TYPE1_BAR0	0x0010	/* not used */
+#define R_LDT_TYPE1_BAR1	0x0014	/* not used */
+
+#define R_LDT_TYPE1_BUSID	0x0018	/* bus ID register */
+#define R_LDT_TYPE1_SECSTATUS	0x001C	/* secondary status / I/O base/limit */
+#define R_LDT_TYPE1_MEMLIMIT	0x0020
+#define R_LDT_TYPE1_PREFETCH	0x0024
+#define R_LDT_TYPE1_PREF_BASE	0x0028
+#define R_LDT_TYPE1_PREF_LIMIT	0x002C
+#define R_LDT_TYPE1_IOLIMIT	0x0030
+#define R_LDT_TYPE1_CAPPTR	0x0034
+#define R_LDT_TYPE1_ROMADDR	0x0038
+#define R_LDT_TYPE1_BRCTL	0x003C
+#define R_LDT_TYPE1_CMD		0x0040
+#define R_LDT_TYPE1_LINKCTRL	0x0044
+#define R_LDT_TYPE1_LINKFREQ	0x0048
+#define R_LDT_TYPE1_RESERVED1	0x004C
+#define R_LDT_TYPE1_SRICMD	0x0050
+#define R_LDT_TYPE1_SRITXNUM	0x0054
+#define R_LDT_TYPE1_SRIRXNUM	0x0058
+#define R_LDT_TYPE1_ERRSTATUS	0x0068
+#define R_LDT_TYPE1_SRICTRL	0x006C
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1)
+#define R_LDT_TYPE1_ADDSTATUS	0x0070
+#endif /* 1250 PASS2 || 112x PASS1 */
+#define R_LDT_TYPE1_TXBUFCNT	0x00C8
+#define R_LDT_TYPE1_EXPCRC	0x00DC
+#define R_LDT_TYPE1_RXCRC	0x00F0
+
+
+/*
+ * LDT Device ID register
+ */
+
+#define S_LDT_DEVICEID_VENDOR		0
+#define M_LDT_DEVICEID_VENDOR		_SB_MAKEMASK_32(16, S_LDT_DEVICEID_VENDOR)
+#define V_LDT_DEVICEID_VENDOR(x)	_SB_MAKEVALUE_32(x, S_LDT_DEVICEID_VENDOR)
+#define G_LDT_DEVICEID_VENDOR(x)	_SB_GETVALUE_32(x, S_LDT_DEVICEID_VENDOR, M_LDT_DEVICEID_VENDOR)
+
+#define S_LDT_DEVICEID_DEVICEID		16
+#define M_LDT_DEVICEID_DEVICEID		_SB_MAKEMASK_32(16, S_LDT_DEVICEID_DEVICEID)
+#define V_LDT_DEVICEID_DEVICEID(x)	_SB_MAKEVALUE_32(x, S_LDT_DEVICEID_DEVICEID)
+#define G_LDT_DEVICEID_DEVICEID(x)	_SB_GETVALUE_32(x, S_LDT_DEVICEID_DEVICEID, M_LDT_DEVICEID_DEVICEID)
+
+
+/*
+ * LDT Command Register (Table 8-13)
+ */
+
+#define M_LDT_CMD_IOSPACE_EN		_SB_MAKEMASK1_32(0)
+#define M_LDT_CMD_MEMSPACE_EN		_SB_MAKEMASK1_32(1)
+#define M_LDT_CMD_MASTER_EN		_SB_MAKEMASK1_32(2)
+#define M_LDT_CMD_SPECCYC_EN		_SB_MAKEMASK1_32(3)
+#define M_LDT_CMD_MEMWRINV_EN		_SB_MAKEMASK1_32(4)
+#define M_LDT_CMD_VGAPALSNP_EN		_SB_MAKEMASK1_32(5)
+#define M_LDT_CMD_PARERRRESP		_SB_MAKEMASK1_32(6)
+#define M_LDT_CMD_WAITCYCCTRL		_SB_MAKEMASK1_32(7)
+#define M_LDT_CMD_SERR_EN		_SB_MAKEMASK1_32(8)
+#define M_LDT_CMD_FASTB2B_EN		_SB_MAKEMASK1_32(9)
+
+/*
+ * LDT class and revision registers
+ */
+
+#define S_LDT_CLASSREV_REV		0
+#define M_LDT_CLASSREV_REV		_SB_MAKEMASK_32(8, S_LDT_CLASSREV_REV)
+#define V_LDT_CLASSREV_REV(x)		_SB_MAKEVALUE_32(x, S_LDT_CLASSREV_REV)
+#define G_LDT_CLASSREV_REV(x)		_SB_GETVALUE_32(x, S_LDT_CLASSREV_REV, M_LDT_CLASSREV_REV)
+
+#define S_LDT_CLASSREV_CLASS		8
+#define M_LDT_CLASSREV_CLASS		_SB_MAKEMASK_32(24, S_LDT_CLASSREV_CLASS)
+#define V_LDT_CLASSREV_CLASS(x)		_SB_MAKEVALUE_32(x, S_LDT_CLASSREV_CLASS)
+#define G_LDT_CLASSREV_CLASS(x)		_SB_GETVALUE_32(x, S_LDT_CLASSREV_CLASS, M_LDT_CLASSREV_CLASS)
+
+#define K_LDT_REV			0x01
+#define K_LDT_CLASS			0x060000
+
+/*
+ * Device Header (offset 0x0C)
+ */
+
+#define S_LDT_DEVHDR_CLINESZ		0
+#define M_LDT_DEVHDR_CLINESZ		_SB_MAKEMASK_32(8, S_LDT_DEVHDR_CLINESZ)
+#define V_LDT_DEVHDR_CLINESZ(x)		_SB_MAKEVALUE_32(x, S_LDT_DEVHDR_CLINESZ)
+#define G_LDT_DEVHDR_CLINESZ(x)		_SB_GETVALUE_32(x, S_LDT_DEVHDR_CLINESZ, M_LDT_DEVHDR_CLINESZ)
+
+#define S_LDT_DEVHDR_LATTMR		8
+#define M_LDT_DEVHDR_LATTMR		_SB_MAKEMASK_32(8, S_LDT_DEVHDR_LATTMR)
+#define V_LDT_DEVHDR_LATTMR(x)		_SB_MAKEVALUE_32(x, S_LDT_DEVHDR_LATTMR)
+#define G_LDT_DEVHDR_LATTMR(x)		_SB_GETVALUE_32(x, S_LDT_DEVHDR_LATTMR, M_LDT_DEVHDR_LATTMR)
+
+#define S_LDT_DEVHDR_HDRTYPE		16
+#define M_LDT_DEVHDR_HDRTYPE		_SB_MAKEMASK_32(8, S_LDT_DEVHDR_HDRTYPE)
+#define V_LDT_DEVHDR_HDRTYPE(x)		_SB_MAKEVALUE_32(x, S_LDT_DEVHDR_HDRTYPE)
+#define G_LDT_DEVHDR_HDRTYPE(x)		_SB_GETVALUE_32(x, S_LDT_DEVHDR_HDRTYPE, M_LDT_DEVHDR_HDRTYPE)
+
+#define K_LDT_DEVHDR_HDRTYPE_TYPE1	1
+
+#define S_LDT_DEVHDR_BIST		24
+#define M_LDT_DEVHDR_BIST		_SB_MAKEMASK_32(8, S_LDT_DEVHDR_BIST)
+#define V_LDT_DEVHDR_BIST(x)		_SB_MAKEVALUE_32(x, S_LDT_DEVHDR_BIST)
+#define G_LDT_DEVHDR_BIST(x)		_SB_GETVALUE_32(x, S_LDT_DEVHDR_BIST, M_LDT_DEVHDR_BIST)
+
+
+
+/*
+ * LDT Status Register (Table 8-14).  Note that these constants
+ * assume you've read the command and status register
+ * together (32-bit read at offset 0x04)
+ *
+ * These bits also apply to the secondary status
+ * register (Table 8-15), offset 0x1C
+ */
+
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1)
+#define M_LDT_STATUS_VGAEN		_SB_MAKEMASK1_32(3)
+#endif /* 1250 PASS2 || 112x PASS1 */
+#define M_LDT_STATUS_CAPLIST		_SB_MAKEMASK1_32(20)
+#define M_LDT_STATUS_66MHZCAP		_SB_MAKEMASK1_32(21)
+#define M_LDT_STATUS_RESERVED2		_SB_MAKEMASK1_32(22)
+#define M_LDT_STATUS_FASTB2BCAP		_SB_MAKEMASK1_32(23)
+#define M_LDT_STATUS_MSTRDPARERR	_SB_MAKEMASK1_32(24)
+
+#define S_LDT_STATUS_DEVSELTIMING	25
+#define M_LDT_STATUS_DEVSELTIMING	_SB_MAKEMASK_32(2, S_LDT_STATUS_DEVSELTIMING)
+#define V_LDT_STATUS_DEVSELTIMING(x)	_SB_MAKEVALUE_32(x, S_LDT_STATUS_DEVSELTIMING)
+#define G_LDT_STATUS_DEVSELTIMING(x)	_SB_GETVALUE_32(x, S_LDT_STATUS_DEVSELTIMING, M_LDT_STATUS_DEVSELTIMING)
+
+#define M_LDT_STATUS_SIGDTGTABORT	_SB_MAKEMASK1_32(27)
+#define M_LDT_STATUS_RCVDTGTABORT	_SB_MAKEMASK1_32(28)
+#define M_LDT_STATUS_RCVDMSTRABORT	_SB_MAKEMASK1_32(29)
+#define M_LDT_STATUS_SIGDSERR		_SB_MAKEMASK1_32(30)
+#define M_LDT_STATUS_DETPARERR		_SB_MAKEMASK1_32(31)
+
+/*
+ * Bridge Control Register (Table 8-16).  Note that these
+ * constants assume you've read the register as a 32-bit
+ * read (offset 0x3C)
+ */
+
+#define M_LDT_BRCTL_PARERRRESP_EN	_SB_MAKEMASK1_32(16)
+#define M_LDT_BRCTL_SERR_EN		_SB_MAKEMASK1_32(17)
+#define M_LDT_BRCTL_ISA_EN		_SB_MAKEMASK1_32(18)
+#define M_LDT_BRCTL_VGA_EN		_SB_MAKEMASK1_32(19)
+#define M_LDT_BRCTL_MSTRABORTMODE	_SB_MAKEMASK1_32(21)
+#define M_LDT_BRCTL_SECBUSRESET		_SB_MAKEMASK1_32(22)
+#define M_LDT_BRCTL_FASTB2B_EN		_SB_MAKEMASK1_32(23)
+#define M_LDT_BRCTL_PRIDISCARD		_SB_MAKEMASK1_32(24)
+#define M_LDT_BRCTL_SECDISCARD		_SB_MAKEMASK1_32(25)
+#define M_LDT_BRCTL_DISCARDSTAT		_SB_MAKEMASK1_32(26)
+#define M_LDT_BRCTL_DISCARDSERR_EN	_SB_MAKEMASK1_32(27)
+
+/*
+ * LDT Command Register (Table 8-17).  Note that these constants
+ * assume you've read the command and status register together
+ * 32-bit read at offset 0x40
+ */
+
+#define M_LDT_CMD_WARMRESET		_SB_MAKEMASK1_32(16)
+#define M_LDT_CMD_DOUBLEENDED		_SB_MAKEMASK1_32(17)
+
+#define S_LDT_CMD_CAPTYPE		29
+#define M_LDT_CMD_CAPTYPE		_SB_MAKEMASK_32(3, S_LDT_CMD_CAPTYPE)
+#define V_LDT_CMD_CAPTYPE(x)		_SB_MAKEVALUE_32(x, S_LDT_CMD_CAPTYPE)
+#define G_LDT_CMD_CAPTYPE(x)		_SB_GETVALUE_32(x, S_LDT_CMD_CAPTYPE, M_LDT_CMD_CAPTYPE)
+
+/*
+ * LDT link control register (Table 8-18), and (Table 8-19)
+ */
+
+#define M_LDT_LINKCTRL_CAPSYNCFLOOD_EN	_SB_MAKEMASK1_32(1)
+#define M_LDT_LINKCTRL_CRCSTARTTEST	_SB_MAKEMASK1_32(2)
+#define M_LDT_LINKCTRL_CRCFORCEERR	_SB_MAKEMASK1_32(3)
+#define M_LDT_LINKCTRL_LINKFAIL		_SB_MAKEMASK1_32(4)
+#define M_LDT_LINKCTRL_INITDONE		_SB_MAKEMASK1_32(5)
+#define M_LDT_LINKCTRL_EOC		_SB_MAKEMASK1_32(6)
+#define M_LDT_LINKCTRL_XMITOFF		_SB_MAKEMASK1_32(7)
+
+#define S_LDT_LINKCTRL_CRCERR		8
+#define M_LDT_LINKCTRL_CRCERR		_SB_MAKEMASK_32(4, S_LDT_LINKCTRL_CRCERR)
+#define V_LDT_LINKCTRL_CRCERR(x)	_SB_MAKEVALUE_32(x, S_LDT_LINKCTRL_CRCERR)
+#define G_LDT_LINKCTRL_CRCERR(x)	_SB_GETVALUE_32(x, S_LDT_LINKCTRL_CRCERR, M_LDT_LINKCTRL_CRCERR)
+
+#define S_LDT_LINKCTRL_MAXIN		16
+#define M_LDT_LINKCTRL_MAXIN		_SB_MAKEMASK_32(3, S_LDT_LINKCTRL_MAXIN)
+#define V_LDT_LINKCTRL_MAXIN(x)		_SB_MAKEVALUE_32(x, S_LDT_LINKCTRL_MAXIN)
+#define G_LDT_LINKCTRL_MAXIN(x)		_SB_GETVALUE_32(x, S_LDT_LINKCTRL_MAXIN, M_LDT_LINKCTRL_MAXIN)
+
+#define M_LDT_LINKCTRL_DWFCLN		_SB_MAKEMASK1_32(19)
+
+#define S_LDT_LINKCTRL_MAXOUT		20
+#define M_LDT_LINKCTRL_MAXOUT		_SB_MAKEMASK_32(3, S_LDT_LINKCTRL_MAXOUT)
+#define V_LDT_LINKCTRL_MAXOUT(x)	_SB_MAKEVALUE_32(x, S_LDT_LINKCTRL_MAXOUT)
+#define G_LDT_LINKCTRL_MAXOUT(x)	_SB_GETVALUE_32(x, S_LDT_LINKCTRL_MAXOUT, M_LDT_LINKCTRL_MAXOUT)
+
+#define M_LDT_LINKCTRL_DWFCOUT		_SB_MAKEMASK1_32(23)
+
+#define S_LDT_LINKCTRL_WIDTHIN		24
+#define M_LDT_LINKCTRL_WIDTHIN		_SB_MAKEMASK_32(3, S_LDT_LINKCTRL_WIDTHIN)
+#define V_LDT_LINKCTRL_WIDTHIN(x)	_SB_MAKEVALUE_32(x, S_LDT_LINKCTRL_WIDTHIN)
+#define G_LDT_LINKCTRL_WIDTHIN(x)	_SB_GETVALUE_32(x, S_LDT_LINKCTRL_WIDTHIN, M_LDT_LINKCTRL_WIDTHIN)
+
+#define M_LDT_LINKCTRL_DWFCLIN_EN	_SB_MAKEMASK1_32(27)
+
+#define S_LDT_LINKCTRL_WIDTHOUT		28
+#define M_LDT_LINKCTRL_WIDTHOUT		_SB_MAKEMASK_32(3, S_LDT_LINKCTRL_WIDTHOUT)
+#define V_LDT_LINKCTRL_WIDTHOUT(x)	_SB_MAKEVALUE_32(x, S_LDT_LINKCTRL_WIDTHOUT)
+#define G_LDT_LINKCTRL_WIDTHOUT(x)	_SB_GETVALUE_32(x, S_LDT_LINKCTRL_WIDTHOUT, M_LDT_LINKCTRL_WIDTHOUT)
+
+#define M_LDT_LINKCTRL_DWFCOUT_EN	_SB_MAKEMASK1_32(31)
+
+/*
+ * LDT Link frequency register	(Table 8-20) offset 0x48
+ */
+
+#define S_LDT_LINKFREQ_FREQ		8
+#define M_LDT_LINKFREQ_FREQ		_SB_MAKEMASK_32(4, S_LDT_LINKFREQ_FREQ)
+#define V_LDT_LINKFREQ_FREQ(x)		_SB_MAKEVALUE_32(x, S_LDT_LINKFREQ_FREQ)
+#define G_LDT_LINKFREQ_FREQ(x)		_SB_GETVALUE_32(x, S_LDT_LINKFREQ_FREQ, M_LDT_LINKFREQ_FREQ)
+
+#define K_LDT_LINKFREQ_200MHZ		0
+#define K_LDT_LINKFREQ_300MHZ		1
+#define K_LDT_LINKFREQ_400MHZ		2
+#define K_LDT_LINKFREQ_500MHZ		3
+#define K_LDT_LINKFREQ_600MHZ		4
+#define K_LDT_LINKFREQ_800MHZ		5
+#define K_LDT_LINKFREQ_1000MHZ		6
+
+/*
+ * LDT SRI Command Register (Table 8-21).  Note that these constants
+ * assume you've read the command and status register together
+ * 32-bit read at offset 0x50
+ */
+
+#define M_LDT_SRICMD_SIPREADY		_SB_MAKEMASK1_32(16)
+#define M_LDT_SRICMD_SYNCPTRCTL		_SB_MAKEMASK1_32(17)
+#define M_LDT_SRICMD_REDUCESYNCZERO	_SB_MAKEMASK1_32(18)
+#if SIBYTE_HDR_FEATURE_UP_TO(1250, PASS1)
+#define M_LDT_SRICMD_DISSTARVATIONCNT	_SB_MAKEMASK1_32(19)	/* PASS1 */
+#endif /* up to 1250 PASS1 */
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1)
+#define M_LDT_SRICMD_DISMULTTXVLD	_SB_MAKEMASK1_32(19)
+#define M_LDT_SRICMD_EXPENDIAN		_SB_MAKEMASK1_32(26)
+#endif /* 1250 PASS2 || 112x PASS1 */
+
+
+#define S_LDT_SRICMD_RXMARGIN		20
+#define M_LDT_SRICMD_RXMARGIN		_SB_MAKEMASK_32(5, S_LDT_SRICMD_RXMARGIN)
+#define V_LDT_SRICMD_RXMARGIN(x)	_SB_MAKEVALUE_32(x, S_LDT_SRICMD_RXMARGIN)
+#define G_LDT_SRICMD_RXMARGIN(x)	_SB_GETVALUE_32(x, S_LDT_SRICMD_RXMARGIN, M_LDT_SRICMD_RXMARGIN)
+
+#define M_LDT_SRICMD_LDTPLLCOMPAT	_SB_MAKEMASK1_32(25)
+
+#define S_LDT_SRICMD_TXINITIALOFFSET	28
+#define M_LDT_SRICMD_TXINITIALOFFSET	_SB_MAKEMASK_32(3, S_LDT_SRICMD_TXINITIALOFFSET)
+#define V_LDT_SRICMD_TXINITIALOFFSET(x) _SB_MAKEVALUE_32(x, S_LDT_SRICMD_TXINITIALOFFSET)
+#define G_LDT_SRICMD_TXINITIALOFFSET(x) _SB_GETVALUE_32(x, S_LDT_SRICMD_TXINITIALOFFSET, M_LDT_SRICMD_TXINITIALOFFSET)
+
+#define M_LDT_SRICMD_LINKFREQDIRECT	_SB_MAKEMASK1_32(31)
+
+/*
+ * LDT Error control and status register (Table 8-22) (Table 8-23)
+ */
+
+#define M_LDT_ERRCTL_PROTFATAL_EN	_SB_MAKEMASK1_32(0)
+#define M_LDT_ERRCTL_PROTNONFATAL_EN	_SB_MAKEMASK1_32(1)
+#define M_LDT_ERRCTL_PROTSYNCFLOOD_EN	_SB_MAKEMASK1_32(2)
+#define M_LDT_ERRCTL_OVFFATAL_EN	_SB_MAKEMASK1_32(3)
+#define M_LDT_ERRCTL_OVFNONFATAL_EN	_SB_MAKEMASK1_32(4)
+#define M_LDT_ERRCTL_OVFSYNCFLOOD_EN	_SB_MAKEMASK1_32(5)
+#define M_LDT_ERRCTL_EOCNXAFATAL_EN	_SB_MAKEMASK1_32(6)
+#define M_LDT_ERRCTL_EOCNXANONFATAL_EN	_SB_MAKEMASK1_32(7)
+#define M_LDT_ERRCTL_EOCNXASYNCFLOOD_EN _SB_MAKEMASK1_32(8)
+#define M_LDT_ERRCTL_CRCFATAL_EN	_SB_MAKEMASK1_32(9)
+#define M_LDT_ERRCTL_CRCNONFATAL_EN	_SB_MAKEMASK1_32(10)
+#define M_LDT_ERRCTL_SERRFATAL_EN	_SB_MAKEMASK1_32(11)
+#define M_LDT_ERRCTL_SRCTAGFATAL_EN	_SB_MAKEMASK1_32(12)
+#define M_LDT_ERRCTL_SRCTAGNONFATAL_EN	_SB_MAKEMASK1_32(13)
+#define M_LDT_ERRCTL_SRCTAGSYNCFLOOD_EN _SB_MAKEMASK1_32(14)
+#define M_LDT_ERRCTL_MAPNXAFATAL_EN	_SB_MAKEMASK1_32(15)
+#define M_LDT_ERRCTL_MAPNXANONFATAL_EN	_SB_MAKEMASK1_32(16)
+#define M_LDT_ERRCTL_MAPNXASYNCFLOOD_EN _SB_MAKEMASK1_32(17)
+
+#define M_LDT_ERRCTL_PROTOERR		_SB_MAKEMASK1_32(24)
+#define M_LDT_ERRCTL_OVFERR		_SB_MAKEMASK1_32(25)
+#define M_LDT_ERRCTL_EOCNXAERR		_SB_MAKEMASK1_32(26)
+#define M_LDT_ERRCTL_SRCTAGERR		_SB_MAKEMASK1_32(27)
+#define M_LDT_ERRCTL_MAPNXAERR		_SB_MAKEMASK1_32(28)
+
+/*
+ * SRI Control register (Table 8-24, 8-25)  Offset 0x6C
+ */
+
+#define S_LDT_SRICTRL_NEEDRESP		0
+#define M_LDT_SRICTRL_NEEDRESP		_SB_MAKEMASK_32(2, S_LDT_SRICTRL_NEEDRESP)
+#define V_LDT_SRICTRL_NEEDRESP(x)	_SB_MAKEVALUE_32(x, S_LDT_SRICTRL_NEEDRESP)
+#define G_LDT_SRICTRL_NEEDRESP(x)	_SB_GETVALUE_32(x, S_LDT_SRICTRL_NEEDRESP, M_LDT_SRICTRL_NEEDRESP)
+
+#define S_LDT_SRICTRL_NEEDNPREQ		2
+#define M_LDT_SRICTRL_NEEDNPREQ		_SB_MAKEMASK_32(2, S_LDT_SRICTRL_NEEDNPREQ)
+#define V_LDT_SRICTRL_NEEDNPREQ(x)	_SB_MAKEVALUE_32(x, S_LDT_SRICTRL_NEEDNPREQ)
+#define G_LDT_SRICTRL_NEEDNPREQ(x)	_SB_GETVALUE_32(x, S_LDT_SRICTRL_NEEDNPREQ, M_LDT_SRICTRL_NEEDNPREQ)
+
+#define S_LDT_SRICTRL_NEEDPREQ		4
+#define M_LDT_SRICTRL_NEEDPREQ		_SB_MAKEMASK_32(2, S_LDT_SRICTRL_NEEDPREQ)
+#define V_LDT_SRICTRL_NEEDPREQ(x)	_SB_MAKEVALUE_32(x, S_LDT_SRICTRL_NEEDPREQ)
+#define G_LDT_SRICTRL_NEEDPREQ(x)	_SB_GETVALUE_32(x, S_LDT_SRICTRL_NEEDPREQ, M_LDT_SRICTRL_NEEDPREQ)
+
+#define S_LDT_SRICTRL_WANTRESP		8
+#define M_LDT_SRICTRL_WANTRESP		_SB_MAKEMASK_32(2, S_LDT_SRICTRL_WANTRESP)
+#define V_LDT_SRICTRL_WANTRESP(x)	_SB_MAKEVALUE_32(x, S_LDT_SRICTRL_WANTRESP)
+#define G_LDT_SRICTRL_WANTRESP(x)	_SB_GETVALUE_32(x, S_LDT_SRICTRL_WANTRESP, M_LDT_SRICTRL_WANTRESP)
+
+#define S_LDT_SRICTRL_WANTNPREQ		10
+#define M_LDT_SRICTRL_WANTNPREQ		_SB_MAKEMASK_32(2, S_LDT_SRICTRL_WANTNPREQ)
+#define V_LDT_SRICTRL_WANTNPREQ(x)	_SB_MAKEVALUE_32(x, S_LDT_SRICTRL_WANTNPREQ)
+#define G_LDT_SRICTRL_WANTNPREQ(x)	_SB_GETVALUE_32(x, S_LDT_SRICTRL_WANTNPREQ, M_LDT_SRICTRL_WANTNPREQ)
+
+#define S_LDT_SRICTRL_WANTPREQ		12
+#define M_LDT_SRICTRL_WANTPREQ		_SB_MAKEMASK_32(2, S_LDT_SRICTRL_WANTPREQ)
+#define V_LDT_SRICTRL_WANTPREQ(x)	_SB_MAKEVALUE_32(x, S_LDT_SRICTRL_WANTPREQ)
+#define G_LDT_SRICTRL_WANTPREQ(x)	_SB_GETVALUE_32(x, S_LDT_SRICTRL_WANTPREQ, M_LDT_SRICTRL_WANTPREQ)
+
+#define S_LDT_SRICTRL_BUFRELSPACE	16
+#define M_LDT_SRICTRL_BUFRELSPACE	_SB_MAKEMASK_32(4, S_LDT_SRICTRL_BUFRELSPACE)
+#define V_LDT_SRICTRL_BUFRELSPACE(x)	_SB_MAKEVALUE_32(x, S_LDT_SRICTRL_BUFRELSPACE)
+#define G_LDT_SRICTRL_BUFRELSPACE(x)	_SB_GETVALUE_32(x, S_LDT_SRICTRL_BUFRELSPACE, M_LDT_SRICTRL_BUFRELSPACE)
+
+/*
+ * LDT SRI Transmit Buffer Count register (Table 8-26)
+ */
+
+#define S_LDT_TXBUFCNT_PCMD		0
+#define M_LDT_TXBUFCNT_PCMD		_SB_MAKEMASK_32(4, S_LDT_TXBUFCNT_PCMD)
+#define V_LDT_TXBUFCNT_PCMD(x)		_SB_MAKEVALUE_32(x, S_LDT_TXBUFCNT_PCMD)
+#define G_LDT_TXBUFCNT_PCMD(x)		_SB_GETVALUE_32(x, S_LDT_TXBUFCNT_PCMD, M_LDT_TXBUFCNT_PCMD)
+
+#define S_LDT_TXBUFCNT_PDATA		4
+#define M_LDT_TXBUFCNT_PDATA		_SB_MAKEMASK_32(4, S_LDT_TXBUFCNT_PDATA)
+#define V_LDT_TXBUFCNT_PDATA(x)		_SB_MAKEVALUE_32(x, S_LDT_TXBUFCNT_PDATA)
+#define G_LDT_TXBUFCNT_PDATA(x)		_SB_GETVALUE_32(x, S_LDT_TXBUFCNT_PDATA, M_LDT_TXBUFCNT_PDATA)
+
+#define S_LDT_TXBUFCNT_NPCMD		8
+#define M_LDT_TXBUFCNT_NPCMD		_SB_MAKEMASK_32(4, S_LDT_TXBUFCNT_NPCMD)
+#define V_LDT_TXBUFCNT_NPCMD(x)		_SB_MAKEVALUE_32(x, S_LDT_TXBUFCNT_NPCMD)
+#define G_LDT_TXBUFCNT_NPCMD(x)		_SB_GETVALUE_32(x, S_LDT_TXBUFCNT_NPCMD, M_LDT_TXBUFCNT_NPCMD)
+
+#define S_LDT_TXBUFCNT_NPDATA		12
+#define M_LDT_TXBUFCNT_NPDATA		_SB_MAKEMASK_32(4, S_LDT_TXBUFCNT_NPDATA)
+#define V_LDT_TXBUFCNT_NPDATA(x)	_SB_MAKEVALUE_32(x, S_LDT_TXBUFCNT_NPDATA)
+#define G_LDT_TXBUFCNT_NPDATA(x)	_SB_GETVALUE_32(x, S_LDT_TXBUFCNT_NPDATA, M_LDT_TXBUFCNT_NPDATA)
+
+#define S_LDT_TXBUFCNT_RCMD		16
+#define M_LDT_TXBUFCNT_RCMD		_SB_MAKEMASK_32(4, S_LDT_TXBUFCNT_RCMD)
+#define V_LDT_TXBUFCNT_RCMD(x)		_SB_MAKEVALUE_32(x, S_LDT_TXBUFCNT_RCMD)
+#define G_LDT_TXBUFCNT_RCMD(x)		_SB_GETVALUE_32(x, S_LDT_TXBUFCNT_RCMD, M_LDT_TXBUFCNT_RCMD)
+
+#define S_LDT_TXBUFCNT_RDATA		20
+#define M_LDT_TXBUFCNT_RDATA		_SB_MAKEMASK_32(4, S_LDT_TXBUFCNT_RDATA)
+#define V_LDT_TXBUFCNT_RDATA(x)		_SB_MAKEVALUE_32(x, S_LDT_TXBUFCNT_RDATA)
+#define G_LDT_TXBUFCNT_RDATA(x)		_SB_GETVALUE_32(x, S_LDT_TXBUFCNT_RDATA, M_LDT_TXBUFCNT_RDATA)
+
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1)
+/*
+ * Additional Status Register
+ */
+
+#define S_LDT_ADDSTATUS_TGTDONE		0
+#define M_LDT_ADDSTATUS_TGTDONE		_SB_MAKEMASK_32(8, S_LDT_ADDSTATUS_TGTDONE)
+#define V_LDT_ADDSTATUS_TGTDONE(x)	_SB_MAKEVALUE_32(x, S_LDT_ADDSTATUS_TGTDONE)
+#define G_LDT_ADDSTATUS_TGTDONE(x)	_SB_GETVALUE_32(x, S_LDT_ADDSTATUS_TGTDONE, M_LDT_ADDSTATUS_TGTDONE)
+#endif /* 1250 PASS2 || 112x PASS1 */
+
+#endif
diff --git a/arch/mips/include/asm/sibyte/sb1250_mac.h b/arch/mips/include/asm/sibyte/sb1250_mac.h
new file mode 100644
index 000000000..3ddbd4b5d
--- /dev/null
+++ b/arch/mips/include/asm/sibyte/sb1250_mac.h
@@ -0,0 +1,643 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*  *********************************************************************
+    *  SB1250 Board Support Package
+    *
+    *  MAC constants and macros			File: sb1250_mac.h
+    *
+    *  This module contains constants and macros for the SB1250's
+    *  ethernet controllers.
+    *
+    *  SB1250 specification level:  User's manual 1/02/02
+    *
+    *********************************************************************
+    *
+    *  Copyright 2000,2001,2002,2003
+    *  Broadcom Corporation. All rights reserved.
+    *
+    ********************************************************************* */
+
+
+#ifndef _SB1250_MAC_H
+#define _SB1250_MAC_H
+
+#include <asm/sibyte/sb1250_defs.h>
+
+/*  *********************************************************************
+    *  Ethernet MAC Registers
+    ********************************************************************* */
+
+/*
+ * MAC Configuration Register (Table 9-13)
+ * Register: MAC_CFG_0
+ * Register: MAC_CFG_1
+ * Register: MAC_CFG_2
+ */
+
+
+#define M_MAC_RESERVED0		    _SB_MAKEMASK1(0)
+#define M_MAC_TX_HOLD_SOP_EN	    _SB_MAKEMASK1(1)
+#define M_MAC_RETRY_EN		    _SB_MAKEMASK1(2)
+#define M_MAC_RET_DRPREQ_EN	    _SB_MAKEMASK1(3)
+#define M_MAC_RET_UFL_EN	    _SB_MAKEMASK1(4)
+#define M_MAC_BURST_EN		    _SB_MAKEMASK1(5)
+
+#define S_MAC_TX_PAUSE		    _SB_MAKE64(6)
+#define M_MAC_TX_PAUSE_CNT	    _SB_MAKEMASK(3, S_MAC_TX_PAUSE)
+#define V_MAC_TX_PAUSE_CNT(x)	    _SB_MAKEVALUE(x, S_MAC_TX_PAUSE)
+
+#define K_MAC_TX_PAUSE_CNT_512	    0
+#define K_MAC_TX_PAUSE_CNT_1K	    1
+#define K_MAC_TX_PAUSE_CNT_2K	    2
+#define K_MAC_TX_PAUSE_CNT_4K	    3
+#define K_MAC_TX_PAUSE_CNT_8K	    4
+#define K_MAC_TX_PAUSE_CNT_16K	    5
+#define K_MAC_TX_PAUSE_CNT_32K	    6
+#define K_MAC_TX_PAUSE_CNT_64K	    7
+
+#define V_MAC_TX_PAUSE_CNT_512	    V_MAC_TX_PAUSE_CNT(K_MAC_TX_PAUSE_CNT_512)
+#define V_MAC_TX_PAUSE_CNT_1K	    V_MAC_TX_PAUSE_CNT(K_MAC_TX_PAUSE_CNT_1K)
+#define V_MAC_TX_PAUSE_CNT_2K	    V_MAC_TX_PAUSE_CNT(K_MAC_TX_PAUSE_CNT_2K)
+#define V_MAC_TX_PAUSE_CNT_4K	    V_MAC_TX_PAUSE_CNT(K_MAC_TX_PAUSE_CNT_4K)
+#define V_MAC_TX_PAUSE_CNT_8K	    V_MAC_TX_PAUSE_CNT(K_MAC_TX_PAUSE_CNT_8K)
+#define V_MAC_TX_PAUSE_CNT_16K	    V_MAC_TX_PAUSE_CNT(K_MAC_TX_PAUSE_CNT_16K)
+#define V_MAC_TX_PAUSE_CNT_32K	    V_MAC_TX_PAUSE_CNT(K_MAC_TX_PAUSE_CNT_32K)
+#define V_MAC_TX_PAUSE_CNT_64K	    V_MAC_TX_PAUSE_CNT(K_MAC_TX_PAUSE_CNT_64K)
+
+#define M_MAC_RESERVED1		    _SB_MAKEMASK(8, 9)
+
+#define M_MAC_AP_STAT_EN	    _SB_MAKEMASK1(17)
+
+#if SIBYTE_HDR_FEATURE_CHIP(1480)
+#define M_MAC_TIMESTAMP		    _SB_MAKEMASK1(18)
+#endif
+#define M_MAC_DRP_ERRPKT_EN	    _SB_MAKEMASK1(19)
+#define M_MAC_DRP_FCSERRPKT_EN	    _SB_MAKEMASK1(20)
+#define M_MAC_DRP_CODEERRPKT_EN	    _SB_MAKEMASK1(21)
+#define M_MAC_DRP_DRBLERRPKT_EN	    _SB_MAKEMASK1(22)
+#define M_MAC_DRP_RNTPKT_EN	    _SB_MAKEMASK1(23)
+#define M_MAC_DRP_OSZPKT_EN	    _SB_MAKEMASK1(24)
+#define M_MAC_DRP_LENERRPKT_EN	    _SB_MAKEMASK1(25)
+
+#define M_MAC_RESERVED3		    _SB_MAKEMASK(6, 26)
+
+#define M_MAC_BYPASS_SEL	    _SB_MAKEMASK1(32)
+#define M_MAC_HDX_EN		    _SB_MAKEMASK1(33)
+
+#define S_MAC_SPEED_SEL		    _SB_MAKE64(34)
+#define M_MAC_SPEED_SEL		    _SB_MAKEMASK(2, S_MAC_SPEED_SEL)
+#define V_MAC_SPEED_SEL(x)	    _SB_MAKEVALUE(x, S_MAC_SPEED_SEL)
+#define G_MAC_SPEED_SEL(x)	    _SB_GETVALUE(x, S_MAC_SPEED_SEL, M_MAC_SPEED_SEL)
+
+#define K_MAC_SPEED_SEL_10MBPS	    0
+#define K_MAC_SPEED_SEL_100MBPS	    1
+#define K_MAC_SPEED_SEL_1000MBPS    2
+#define K_MAC_SPEED_SEL_RESERVED    3
+
+#define V_MAC_SPEED_SEL_10MBPS	    V_MAC_SPEED_SEL(K_MAC_SPEED_SEL_10MBPS)
+#define V_MAC_SPEED_SEL_100MBPS	    V_MAC_SPEED_SEL(K_MAC_SPEED_SEL_100MBPS)
+#define V_MAC_SPEED_SEL_1000MBPS    V_MAC_SPEED_SEL(K_MAC_SPEED_SEL_1000MBPS)
+#define V_MAC_SPEED_SEL_RESERVED    V_MAC_SPEED_SEL(K_MAC_SPEED_SEL_RESERVED)
+
+#define M_MAC_TX_CLK_EDGE_SEL	    _SB_MAKEMASK1(36)
+#define M_MAC_LOOPBACK_SEL	    _SB_MAKEMASK1(37)
+#define M_MAC_FAST_SYNC		    _SB_MAKEMASK1(38)
+#define M_MAC_SS_EN		    _SB_MAKEMASK1(39)
+
+#define S_MAC_BYPASS_CFG	    _SB_MAKE64(40)
+#define M_MAC_BYPASS_CFG	    _SB_MAKEMASK(2, S_MAC_BYPASS_CFG)
+#define V_MAC_BYPASS_CFG(x)	    _SB_MAKEVALUE(x, S_MAC_BYPASS_CFG)
+#define G_MAC_BYPASS_CFG(x)	    _SB_GETVALUE(x, S_MAC_BYPASS_CFG, M_MAC_BYPASS_CFG)
+
+#define K_MAC_BYPASS_GMII	    0
+#define K_MAC_BYPASS_ENCODED	    1
+#define K_MAC_BYPASS_SOP	    2
+#define K_MAC_BYPASS_EOP	    3
+
+#define M_MAC_BYPASS_16		    _SB_MAKEMASK1(42)
+#define M_MAC_BYPASS_FCS_CHK	    _SB_MAKEMASK1(43)
+
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define M_MAC_RX_CH_SEL_MSB	    _SB_MAKEMASK1(44)
+#endif /* 1250 PASS2 || 112x PASS1 || 1480*/
+
+#if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define M_MAC_SPLIT_CH_SEL	    _SB_MAKEMASK1(45)
+#endif /* 1250 PASS3 || 112x PASS1 || 1480 */
+
+#define S_MAC_BYPASS_IFG	    _SB_MAKE64(46)
+#define M_MAC_BYPASS_IFG	    _SB_MAKEMASK(8, S_MAC_BYPASS_IFG)
+#define V_MAC_BYPASS_IFG(x)	    _SB_MAKEVALUE(x, S_MAC_BYPASS_IFG)
+#define G_MAC_BYPASS_IFG(x)	    _SB_GETVALUE(x, S_MAC_BYPASS_IFG, M_MAC_BYPASS_IFG)
+
+#define K_MAC_FC_CMD_DISABLED	    0
+#define K_MAC_FC_CMD_ENABLED	    1
+#define K_MAC_FC_CMD_ENAB_FALSECARR 2
+
+#define V_MAC_FC_CMD_DISABLED	    V_MAC_FC_CMD(K_MAC_FC_CMD_DISABLED)
+#define V_MAC_FC_CMD_ENABLED	    V_MAC_FC_CMD(K_MAC_FC_CMD_ENABLED)
+#define V_MAC_FC_CMD_ENAB_FALSECARR V_MAC_FC_CMD(K_MAC_FC_CMD_ENAB_FALSECARR)
+
+#define M_MAC_FC_SEL		    _SB_MAKEMASK1(54)
+
+#define S_MAC_FC_CMD		    _SB_MAKE64(55)
+#define M_MAC_FC_CMD		    _SB_MAKEMASK(2, S_MAC_FC_CMD)
+#define V_MAC_FC_CMD(x)		    _SB_MAKEVALUE(x, S_MAC_FC_CMD)
+#define G_MAC_FC_CMD(x)		    _SB_GETVALUE(x, S_MAC_FC_CMD, M_MAC_FC_CMD)
+
+#define S_MAC_RX_CH_SEL		    _SB_MAKE64(57)
+#define M_MAC_RX_CH_SEL		    _SB_MAKEMASK(7, S_MAC_RX_CH_SEL)
+#define V_MAC_RX_CH_SEL(x)	    _SB_MAKEVALUE(x, S_MAC_RX_CH_SEL)
+#define G_MAC_RX_CH_SEL(x)	    _SB_GETVALUE(x, S_MAC_RX_CH_SEL, M_MAC_RX_CH_SEL)
+
+
+/*
+ * MAC Enable Registers
+ * Register: MAC_ENABLE_0
+ * Register: MAC_ENABLE_1
+ * Register: MAC_ENABLE_2
+ */
+
+#define M_MAC_RXDMA_EN0		    _SB_MAKEMASK1(0)
+#define M_MAC_RXDMA_EN1		    _SB_MAKEMASK1(1)
+#define M_MAC_TXDMA_EN0		    _SB_MAKEMASK1(4)
+#define M_MAC_TXDMA_EN1		    _SB_MAKEMASK1(5)
+
+#define M_MAC_PORT_RESET	    _SB_MAKEMASK1(8)
+
+#if (SIBYTE_HDR_FEATURE_CHIP(1250) || SIBYTE_HDR_FEATURE_CHIP(112x))
+#define M_MAC_RX_ENABLE		    _SB_MAKEMASK1(10)
+#define M_MAC_TX_ENABLE		    _SB_MAKEMASK1(11)
+#define M_MAC_BYP_RX_ENABLE	    _SB_MAKEMASK1(12)
+#define M_MAC_BYP_TX_ENABLE	    _SB_MAKEMASK1(13)
+#endif
+
+/*
+ * MAC reset information register (1280/1255)
+ */
+#if SIBYTE_HDR_FEATURE_CHIP(1480)
+#define M_MAC_RX_CH0_PAUSE_ON	_SB_MAKEMASK1(8)
+#define M_MAC_RX_CH1_PAUSE_ON	_SB_MAKEMASK1(16)
+#define M_MAC_TX_CH0_PAUSE_ON	_SB_MAKEMASK1(24)
+#define M_MAC_TX_CH1_PAUSE_ON	_SB_MAKEMASK1(32)
+#endif
+
+/*
+ * MAC DMA Control Register
+ * Register: MAC_TXD_CTL_0
+ * Register: MAC_TXD_CTL_1
+ * Register: MAC_TXD_CTL_2
+ */
+
+#define S_MAC_TXD_WEIGHT0	    _SB_MAKE64(0)
+#define M_MAC_TXD_WEIGHT0	    _SB_MAKEMASK(4, S_MAC_TXD_WEIGHT0)
+#define V_MAC_TXD_WEIGHT0(x)	    _SB_MAKEVALUE(x, S_MAC_TXD_WEIGHT0)
+#define G_MAC_TXD_WEIGHT0(x)	    _SB_GETVALUE(x, S_MAC_TXD_WEIGHT0, M_MAC_TXD_WEIGHT0)
+
+#define S_MAC_TXD_WEIGHT1	    _SB_MAKE64(4)
+#define M_MAC_TXD_WEIGHT1	    _SB_MAKEMASK(4, S_MAC_TXD_WEIGHT1)
+#define V_MAC_TXD_WEIGHT1(x)	    _SB_MAKEVALUE(x, S_MAC_TXD_WEIGHT1)
+#define G_MAC_TXD_WEIGHT1(x)	    _SB_GETVALUE(x, S_MAC_TXD_WEIGHT1, M_MAC_TXD_WEIGHT1)
+
+/*
+ * MAC Fifo Threshold registers (Table 9-14)
+ * Register: MAC_THRSH_CFG_0
+ * Register: MAC_THRSH_CFG_1
+ * Register: MAC_THRSH_CFG_2
+ */
+
+#define S_MAC_TX_WR_THRSH	    _SB_MAKE64(0)
+#if SIBYTE_HDR_FEATURE_UP_TO(1250, PASS1)
+/* XXX: Can't enable, as it has the same name as a pass2+ define below.	 */
+/* #define M_MAC_TX_WR_THRSH	       _SB_MAKEMASK(6, S_MAC_TX_WR_THRSH) */
+#endif /* up to 1250 PASS1 */
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define M_MAC_TX_WR_THRSH	    _SB_MAKEMASK(7, S_MAC_TX_WR_THRSH)
+#endif /* 1250 PASS2 || 112x PASS1 || 1480 */
+#define V_MAC_TX_WR_THRSH(x)	    _SB_MAKEVALUE(x, S_MAC_TX_WR_THRSH)
+#define G_MAC_TX_WR_THRSH(x)	    _SB_GETVALUE(x, S_MAC_TX_WR_THRSH, M_MAC_TX_WR_THRSH)
+
+#define S_MAC_TX_RD_THRSH	    _SB_MAKE64(8)
+#if SIBYTE_HDR_FEATURE_UP_TO(1250, PASS1)
+/* XXX: Can't enable, as it has the same name as a pass2+ define below.	 */
+/* #define M_MAC_TX_RD_THRSH	       _SB_MAKEMASK(6, S_MAC_TX_RD_THRSH) */
+#endif /* up to 1250 PASS1 */
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define M_MAC_TX_RD_THRSH	    _SB_MAKEMASK(7, S_MAC_TX_RD_THRSH)
+#endif /* 1250 PASS2 || 112x PASS1 || 1480 */
+#define V_MAC_TX_RD_THRSH(x)	    _SB_MAKEVALUE(x, S_MAC_TX_RD_THRSH)
+#define G_MAC_TX_RD_THRSH(x)	    _SB_GETVALUE(x, S_MAC_TX_RD_THRSH, M_MAC_TX_RD_THRSH)
+
+#define S_MAC_TX_RL_THRSH	    _SB_MAKE64(16)
+#define M_MAC_TX_RL_THRSH	    _SB_MAKEMASK(4, S_MAC_TX_RL_THRSH)
+#define V_MAC_TX_RL_THRSH(x)	    _SB_MAKEVALUE(x, S_MAC_TX_RL_THRSH)
+#define G_MAC_TX_RL_THRSH(x)	    _SB_GETVALUE(x, S_MAC_TX_RL_THRSH, M_MAC_TX_RL_THRSH)
+
+#define S_MAC_RX_PL_THRSH	    _SB_MAKE64(24)
+#define M_MAC_RX_PL_THRSH	    _SB_MAKEMASK(6, S_MAC_RX_PL_THRSH)
+#define V_MAC_RX_PL_THRSH(x)	    _SB_MAKEVALUE(x, S_MAC_RX_PL_THRSH)
+#define G_MAC_RX_PL_THRSH(x)	    _SB_GETVALUE(x, S_MAC_RX_PL_THRSH, M_MAC_RX_PL_THRSH)
+
+#define S_MAC_RX_RD_THRSH	    _SB_MAKE64(32)
+#define M_MAC_RX_RD_THRSH	    _SB_MAKEMASK(6, S_MAC_RX_RD_THRSH)
+#define V_MAC_RX_RD_THRSH(x)	    _SB_MAKEVALUE(x, S_MAC_RX_RD_THRSH)
+#define G_MAC_RX_RD_THRSH(x)	    _SB_GETVALUE(x, S_MAC_RX_RD_THRSH, M_MAC_RX_RD_THRSH)
+
+#define S_MAC_RX_RL_THRSH	    _SB_MAKE64(40)
+#define M_MAC_RX_RL_THRSH	    _SB_MAKEMASK(6, S_MAC_RX_RL_THRSH)
+#define V_MAC_RX_RL_THRSH(x)	    _SB_MAKEVALUE(x, S_MAC_RX_RL_THRSH)
+#define G_MAC_RX_RL_THRSH(x)	    _SB_GETVALUE(x, S_MAC_RX_RL_THRSH, M_MAC_RX_RL_THRSH)
+
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define S_MAC_ENC_FC_THRSH	     _SB_MAKE64(56)
+#define M_MAC_ENC_FC_THRSH	     _SB_MAKEMASK(6, S_MAC_ENC_FC_THRSH)
+#define V_MAC_ENC_FC_THRSH(x)	     _SB_MAKEVALUE(x, S_MAC_ENC_FC_THRSH)
+#define G_MAC_ENC_FC_THRSH(x)	     _SB_GETVALUE(x, S_MAC_ENC_FC_THRSH, M_MAC_ENC_FC_THRSH)
+#endif /* 1250 PASS2 || 112x PASS1 || 1480 */
+
+/*
+ * MAC Frame Configuration Registers (Table 9-15)
+ * Register: MAC_FRAME_CFG_0
+ * Register: MAC_FRAME_CFG_1
+ * Register: MAC_FRAME_CFG_2
+ */
+
+/* XXXCGD: ??? Unused in pass2? */
+#define S_MAC_IFG_RX		    _SB_MAKE64(0)
+#define M_MAC_IFG_RX		    _SB_MAKEMASK(6, S_MAC_IFG_RX)
+#define V_MAC_IFG_RX(x)		    _SB_MAKEVALUE(x, S_MAC_IFG_RX)
+#define G_MAC_IFG_RX(x)		    _SB_GETVALUE(x, S_MAC_IFG_RX, M_MAC_IFG_RX)
+
+#if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define S_MAC_PRE_LEN		    _SB_MAKE64(0)
+#define M_MAC_PRE_LEN		    _SB_MAKEMASK(6, S_MAC_PRE_LEN)
+#define V_MAC_PRE_LEN(x)	    _SB_MAKEVALUE(x, S_MAC_PRE_LEN)
+#define G_MAC_PRE_LEN(x)	    _SB_GETVALUE(x, S_MAC_PRE_LEN, M_MAC_PRE_LEN)
+#endif /* 1250 PASS3 || 112x PASS1 || 1480 */
+
+#define S_MAC_IFG_TX		    _SB_MAKE64(6)
+#define M_MAC_IFG_TX		    _SB_MAKEMASK(6, S_MAC_IFG_TX)
+#define V_MAC_IFG_TX(x)		    _SB_MAKEVALUE(x, S_MAC_IFG_TX)
+#define G_MAC_IFG_TX(x)		    _SB_GETVALUE(x, S_MAC_IFG_TX, M_MAC_IFG_TX)
+
+#define S_MAC_IFG_THRSH		    _SB_MAKE64(12)
+#define M_MAC_IFG_THRSH		    _SB_MAKEMASK(6, S_MAC_IFG_THRSH)
+#define V_MAC_IFG_THRSH(x)	    _SB_MAKEVALUE(x, S_MAC_IFG_THRSH)
+#define G_MAC_IFG_THRSH(x)	    _SB_GETVALUE(x, S_MAC_IFG_THRSH, M_MAC_IFG_THRSH)
+
+#define S_MAC_BACKOFF_SEL	    _SB_MAKE64(18)
+#define M_MAC_BACKOFF_SEL	    _SB_MAKEMASK(4, S_MAC_BACKOFF_SEL)
+#define V_MAC_BACKOFF_SEL(x)	    _SB_MAKEVALUE(x, S_MAC_BACKOFF_SEL)
+#define G_MAC_BACKOFF_SEL(x)	    _SB_GETVALUE(x, S_MAC_BACKOFF_SEL, M_MAC_BACKOFF_SEL)
+
+#define S_MAC_LFSR_SEED		    _SB_MAKE64(22)
+#define M_MAC_LFSR_SEED		    _SB_MAKEMASK(8, S_MAC_LFSR_SEED)
+#define V_MAC_LFSR_SEED(x)	    _SB_MAKEVALUE(x, S_MAC_LFSR_SEED)
+#define G_MAC_LFSR_SEED(x)	    _SB_GETVALUE(x, S_MAC_LFSR_SEED, M_MAC_LFSR_SEED)
+
+#define S_MAC_SLOT_SIZE		    _SB_MAKE64(30)
+#define M_MAC_SLOT_SIZE		    _SB_MAKEMASK(10, S_MAC_SLOT_SIZE)
+#define V_MAC_SLOT_SIZE(x)	    _SB_MAKEVALUE(x, S_MAC_SLOT_SIZE)
+#define G_MAC_SLOT_SIZE(x)	    _SB_GETVALUE(x, S_MAC_SLOT_SIZE, M_MAC_SLOT_SIZE)
+
+#define S_MAC_MIN_FRAMESZ	    _SB_MAKE64(40)
+#define M_MAC_MIN_FRAMESZ	    _SB_MAKEMASK(8, S_MAC_MIN_FRAMESZ)
+#define V_MAC_MIN_FRAMESZ(x)	    _SB_MAKEVALUE(x, S_MAC_MIN_FRAMESZ)
+#define G_MAC_MIN_FRAMESZ(x)	    _SB_GETVALUE(x, S_MAC_MIN_FRAMESZ, M_MAC_MIN_FRAMESZ)
+
+#define S_MAC_MAX_FRAMESZ	    _SB_MAKE64(48)
+#define M_MAC_MAX_FRAMESZ	    _SB_MAKEMASK(16, S_MAC_MAX_FRAMESZ)
+#define V_MAC_MAX_FRAMESZ(x)	    _SB_MAKEVALUE(x, S_MAC_MAX_FRAMESZ)
+#define G_MAC_MAX_FRAMESZ(x)	    _SB_GETVALUE(x, S_MAC_MAX_FRAMESZ, M_MAC_MAX_FRAMESZ)
+
+/*
+ * These constants are used to configure the fields within the Frame
+ * Configuration Register.
+ */
+
+#define K_MAC_IFG_RX_10		    _SB_MAKE64(0)	/* See table 176, not used */
+#define K_MAC_IFG_RX_100	    _SB_MAKE64(0)
+#define K_MAC_IFG_RX_1000	    _SB_MAKE64(0)
+
+#define K_MAC_IFG_TX_10		    _SB_MAKE64(20)
+#define K_MAC_IFG_TX_100	    _SB_MAKE64(20)
+#define K_MAC_IFG_TX_1000	    _SB_MAKE64(8)
+
+#define K_MAC_IFG_THRSH_10	    _SB_MAKE64(4)
+#define K_MAC_IFG_THRSH_100	    _SB_MAKE64(4)
+#define K_MAC_IFG_THRSH_1000	    _SB_MAKE64(0)
+
+#define K_MAC_SLOT_SIZE_10	    _SB_MAKE64(0)
+#define K_MAC_SLOT_SIZE_100	    _SB_MAKE64(0)
+#define K_MAC_SLOT_SIZE_1000	    _SB_MAKE64(0)
+
+#define V_MAC_IFG_RX_10	       V_MAC_IFG_RX(K_MAC_IFG_RX_10)
+#define V_MAC_IFG_RX_100       V_MAC_IFG_RX(K_MAC_IFG_RX_100)
+#define V_MAC_IFG_RX_1000      V_MAC_IFG_RX(K_MAC_IFG_RX_1000)
+
+#define V_MAC_IFG_TX_10	       V_MAC_IFG_TX(K_MAC_IFG_TX_10)
+#define V_MAC_IFG_TX_100       V_MAC_IFG_TX(K_MAC_IFG_TX_100)
+#define V_MAC_IFG_TX_1000      V_MAC_IFG_TX(K_MAC_IFG_TX_1000)
+
+#define V_MAC_IFG_THRSH_10     V_MAC_IFG_THRSH(K_MAC_IFG_THRSH_10)
+#define V_MAC_IFG_THRSH_100    V_MAC_IFG_THRSH(K_MAC_IFG_THRSH_100)
+#define V_MAC_IFG_THRSH_1000   V_MAC_IFG_THRSH(K_MAC_IFG_THRSH_1000)
+
+#define V_MAC_SLOT_SIZE_10     V_MAC_SLOT_SIZE(K_MAC_SLOT_SIZE_10)
+#define V_MAC_SLOT_SIZE_100    V_MAC_SLOT_SIZE(K_MAC_SLOT_SIZE_100)
+#define V_MAC_SLOT_SIZE_1000   V_MAC_SLOT_SIZE(K_MAC_SLOT_SIZE_1000)
+
+#define K_MAC_MIN_FRAMESZ_FIFO	    _SB_MAKE64(9)
+#define K_MAC_MIN_FRAMESZ_DEFAULT   _SB_MAKE64(64)
+#define K_MAC_MAX_FRAMESZ_DEFAULT   _SB_MAKE64(1518)
+#define K_MAC_MAX_FRAMESZ_JUMBO	    _SB_MAKE64(9216)
+
+#define V_MAC_MIN_FRAMESZ_FIFO	    V_MAC_MIN_FRAMESZ(K_MAC_MIN_FRAMESZ_FIFO)
+#define V_MAC_MIN_FRAMESZ_DEFAULT   V_MAC_MIN_FRAMESZ(K_MAC_MIN_FRAMESZ_DEFAULT)
+#define V_MAC_MAX_FRAMESZ_DEFAULT   V_MAC_MAX_FRAMESZ(K_MAC_MAX_FRAMESZ_DEFAULT)
+#define V_MAC_MAX_FRAMESZ_JUMBO	    V_MAC_MAX_FRAMESZ(K_MAC_MAX_FRAMESZ_JUMBO)
+
+/*
+ * MAC VLAN Tag Registers (Table 9-16)
+ * Register: MAC_VLANTAG_0
+ * Register: MAC_VLANTAG_1
+ * Register: MAC_VLANTAG_2
+ */
+
+#define S_MAC_VLAN_TAG		 _SB_MAKE64(0)
+#define M_MAC_VLAN_TAG		 _SB_MAKEMASK(32, S_MAC_VLAN_TAG)
+#define V_MAC_VLAN_TAG(x)	 _SB_MAKEVALUE(x, S_MAC_VLAN_TAG)
+#define G_MAC_VLAN_TAG(x)	 _SB_GETVALUE(x, S_MAC_VLAN_TAG, M_MAC_VLAN_TAG)
+
+#if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1)
+#define S_MAC_TX_PKT_OFFSET	 _SB_MAKE64(32)
+#define M_MAC_TX_PKT_OFFSET	 _SB_MAKEMASK(8, S_MAC_TX_PKT_OFFSET)
+#define V_MAC_TX_PKT_OFFSET(x)	 _SB_MAKEVALUE(x, S_MAC_TX_PKT_OFFSET)
+#define G_MAC_TX_PKT_OFFSET(x)	 _SB_GETVALUE(x, S_MAC_TX_PKT_OFFSET, M_MAC_TX_PKT_OFFSET)
+
+#define S_MAC_TX_CRC_OFFSET	 _SB_MAKE64(40)
+#define M_MAC_TX_CRC_OFFSET	 _SB_MAKEMASK(8, S_MAC_TX_CRC_OFFSET)
+#define V_MAC_TX_CRC_OFFSET(x)	 _SB_MAKEVALUE(x, S_MAC_TX_CRC_OFFSET)
+#define G_MAC_TX_CRC_OFFSET(x)	 _SB_GETVALUE(x, S_MAC_TX_CRC_OFFSET, M_MAC_TX_CRC_OFFSET)
+
+#define M_MAC_CH_BASE_FC_EN	 _SB_MAKEMASK1(48)
+#endif /* 1250 PASS3 || 112x PASS1 */
+
+/*
+ * MAC Status Registers (Table 9-17)
+ * Also used for the MAC Interrupt Mask Register (Table 9-18)
+ * Register: MAC_STATUS_0
+ * Register: MAC_STATUS_1
+ * Register: MAC_STATUS_2
+ * Register: MAC_INT_MASK_0
+ * Register: MAC_INT_MASK_1
+ * Register: MAC_INT_MASK_2
+ */
+
+/*
+ * Use these constants to shift the appropriate channel
+ * into the CH0 position so the same tests can be used
+ * on each channel.
+ */
+
+#define S_MAC_RX_CH0		    _SB_MAKE64(0)
+#define S_MAC_RX_CH1		    _SB_MAKE64(8)
+#define S_MAC_TX_CH0		    _SB_MAKE64(16)
+#define S_MAC_TX_CH1		    _SB_MAKE64(24)
+
+#define S_MAC_TXCHANNELS	    _SB_MAKE64(16)	/* this is 1st TX chan */
+#define S_MAC_CHANWIDTH		    _SB_MAKE64(8)	/* bits between channels */
+
+/*
+ *  These are the same as RX channel 0.	 The idea here
+ *  is that you'll use one of the "S_" things above
+ *  and pass just the six bits to a DMA-channel-specific ISR
+ */
+#define M_MAC_INT_CHANNEL	    _SB_MAKEMASK(8, 0)
+#define M_MAC_INT_EOP_COUNT	    _SB_MAKEMASK1(0)
+#define M_MAC_INT_EOP_TIMER	    _SB_MAKEMASK1(1)
+#define M_MAC_INT_EOP_SEEN	    _SB_MAKEMASK1(2)
+#define M_MAC_INT_HWM		    _SB_MAKEMASK1(3)
+#define M_MAC_INT_LWM		    _SB_MAKEMASK1(4)
+#define M_MAC_INT_DSCR		    _SB_MAKEMASK1(5)
+#define M_MAC_INT_ERR		    _SB_MAKEMASK1(6)
+#define M_MAC_INT_DZERO		    _SB_MAKEMASK1(7)	/* only for TX channels */
+#define M_MAC_INT_DROP		    _SB_MAKEMASK1(7)	/* only for RX channels */
+
+/*
+ * In the following definitions we use ch (0/1) and txrx (TX=1, RX=0, see
+ * also DMA_TX/DMA_RX in sb_regs.h).
+ */
+#define S_MAC_STATUS_CH_OFFSET(ch, txrx) _SB_MAKE64(((ch) + 2 * (txrx)) * S_MAC_CHANWIDTH)
+
+#define M_MAC_STATUS_CHANNEL(ch, txrx)	 _SB_MAKEVALUE(_SB_MAKEMASK(8, 0), S_MAC_STATUS_CH_OFFSET(ch, txrx))
+#define M_MAC_STATUS_EOP_COUNT(ch, txrx) _SB_MAKEVALUE(M_MAC_INT_EOP_COUNT, S_MAC_STATUS_CH_OFFSET(ch, txrx))
+#define M_MAC_STATUS_EOP_TIMER(ch, txrx) _SB_MAKEVALUE(M_MAC_INT_EOP_TIMER, S_MAC_STATUS_CH_OFFSET(ch, txrx))
+#define M_MAC_STATUS_EOP_SEEN(ch, txrx)	 _SB_MAKEVALUE(M_MAC_INT_EOP_SEEN, S_MAC_STATUS_CH_OFFSET(ch, txrx))
+#define M_MAC_STATUS_HWM(ch, txrx)	 _SB_MAKEVALUE(M_MAC_INT_HWM, S_MAC_STATUS_CH_OFFSET(ch, txrx))
+#define M_MAC_STATUS_LWM(ch, txrx)	 _SB_MAKEVALUE(M_MAC_INT_LWM, S_MAC_STATUS_CH_OFFSET(ch, txrx))
+#define M_MAC_STATUS_DSCR(ch, txrx)	 _SB_MAKEVALUE(M_MAC_INT_DSCR, S_MAC_STATUS_CH_OFFSET(ch, txrx))
+#define M_MAC_STATUS_ERR(ch, txrx)	 _SB_MAKEVALUE(M_MAC_INT_ERR, S_MAC_STATUS_CH_OFFSET(ch, txrx))
+#define M_MAC_STATUS_DZERO(ch, txrx)	 _SB_MAKEVALUE(M_MAC_INT_DZERO, S_MAC_STATUS_CH_OFFSET(ch, txrx))
+#define M_MAC_STATUS_DROP(ch, txrx)	 _SB_MAKEVALUE(M_MAC_INT_DROP, S_MAC_STATUS_CH_OFFSET(ch, txrx))
+#define M_MAC_STATUS_OTHER_ERR		 _SB_MAKEVALUE(_SB_MAKEMASK(7, 0), 40)
+
+
+#define M_MAC_RX_UNDRFL		    _SB_MAKEMASK1(40)
+#define M_MAC_RX_OVRFL		    _SB_MAKEMASK1(41)
+#define M_MAC_TX_UNDRFL		    _SB_MAKEMASK1(42)
+#define M_MAC_TX_OVRFL		    _SB_MAKEMASK1(43)
+#define M_MAC_LTCOL_ERR		    _SB_MAKEMASK1(44)
+#define M_MAC_EXCOL_ERR		    _SB_MAKEMASK1(45)
+#define M_MAC_CNTR_OVRFL_ERR	    _SB_MAKEMASK1(46)
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define M_MAC_SPLIT_EN		    _SB_MAKEMASK1(47)	/* interrupt mask only */
+#endif /* 1250 PASS2 || 112x PASS1 || 1480 */
+
+#define S_MAC_COUNTER_ADDR	    _SB_MAKE64(47)
+#define M_MAC_COUNTER_ADDR	    _SB_MAKEMASK(5, S_MAC_COUNTER_ADDR)
+#define V_MAC_COUNTER_ADDR(x)	    _SB_MAKEVALUE(x, S_MAC_COUNTER_ADDR)
+#define G_MAC_COUNTER_ADDR(x)	    _SB_GETVALUE(x, S_MAC_COUNTER_ADDR, M_MAC_COUNTER_ADDR)
+
+#if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define M_MAC_TX_PAUSE_ON	    _SB_MAKEMASK1(52)
+#endif /* 1250 PASS3 || 112x PASS1 || 1480 */
+
+/*
+ * MAC Fifo Pointer Registers (Table 9-19)    [Debug register]
+ * Register: MAC_FIFO_PTRS_0
+ * Register: MAC_FIFO_PTRS_1
+ * Register: MAC_FIFO_PTRS_2
+ */
+
+#define S_MAC_TX_WRPTR		    _SB_MAKE64(0)
+#define M_MAC_TX_WRPTR		    _SB_MAKEMASK(6, S_MAC_TX_WRPTR)
+#define V_MAC_TX_WRPTR(x)	    _SB_MAKEVALUE(x, S_MAC_TX_WRPTR)
+#define G_MAC_TX_WRPTR(x)	    _SB_GETVALUE(x, S_MAC_TX_WRPTR, M_MAC_TX_WRPTR)
+
+#define S_MAC_TX_RDPTR		    _SB_MAKE64(8)
+#define M_MAC_TX_RDPTR		    _SB_MAKEMASK(6, S_MAC_TX_RDPTR)
+#define V_MAC_TX_RDPTR(x)	    _SB_MAKEVALUE(x, S_MAC_TX_RDPTR)
+#define G_MAC_TX_RDPTR(x)	    _SB_GETVALUE(x, S_MAC_TX_RDPTR, M_MAC_TX_RDPTR)
+
+#define S_MAC_RX_WRPTR		    _SB_MAKE64(16)
+#define M_MAC_RX_WRPTR		    _SB_MAKEMASK(6, S_MAC_RX_WRPTR)
+#define V_MAC_RX_WRPTR(x)	    _SB_MAKEVALUE(x, S_MAC_RX_WRPTR)
+#define G_MAC_RX_WRPTR(x)	    _SB_GETVALUE(x, S_MAC_RX_WRPTR, M_MAC_TX_WRPTR)
+
+#define S_MAC_RX_RDPTR		    _SB_MAKE64(24)
+#define M_MAC_RX_RDPTR		    _SB_MAKEMASK(6, S_MAC_RX_RDPTR)
+#define V_MAC_RX_RDPTR(x)	    _SB_MAKEVALUE(x, S_MAC_RX_RDPTR)
+#define G_MAC_RX_RDPTR(x)	    _SB_GETVALUE(x, S_MAC_RX_RDPTR, M_MAC_TX_RDPTR)
+
+/*
+ * MAC Fifo End Of Packet Count Registers (Table 9-20)	[Debug register]
+ * Register: MAC_EOPCNT_0
+ * Register: MAC_EOPCNT_1
+ * Register: MAC_EOPCNT_2
+ */
+
+#define S_MAC_TX_EOP_COUNTER	    _SB_MAKE64(0)
+#define M_MAC_TX_EOP_COUNTER	    _SB_MAKEMASK(6, S_MAC_TX_EOP_COUNTER)
+#define V_MAC_TX_EOP_COUNTER(x)	    _SB_MAKEVALUE(x, S_MAC_TX_EOP_COUNTER)
+#define G_MAC_TX_EOP_COUNTER(x)	    _SB_GETVALUE(x, S_MAC_TX_EOP_COUNTER, M_MAC_TX_EOP_COUNTER)
+
+#define S_MAC_RX_EOP_COUNTER	    _SB_MAKE64(8)
+#define M_MAC_RX_EOP_COUNTER	    _SB_MAKEMASK(6, S_MAC_RX_EOP_COUNTER)
+#define V_MAC_RX_EOP_COUNTER(x)	    _SB_MAKEVALUE(x, S_MAC_RX_EOP_COUNTER)
+#define G_MAC_RX_EOP_COUNTER(x)	    _SB_GETVALUE(x, S_MAC_RX_EOP_COUNTER, M_MAC_RX_EOP_COUNTER)
+
+/*
+ * MAC Receive Address Filter Exact Match Registers (Table 9-21)
+ * Registers: MAC_ADDR0_0 through MAC_ADDR7_0
+ * Registers: MAC_ADDR0_1 through MAC_ADDR7_1
+ * Registers: MAC_ADDR0_2 through MAC_ADDR7_2
+ */
+
+/* No bitfields */
+
+/*
+ * MAC Receive Address Filter Mask Registers
+ * Registers: MAC_ADDRMASK0_0 and MAC_ADDRMASK0_1
+ * Registers: MAC_ADDRMASK1_0 and MAC_ADDRMASK1_1
+ * Registers: MAC_ADDRMASK2_0 and MAC_ADDRMASK2_1
+ */
+
+/* No bitfields */
+
+/*
+ * MAC Receive Address Filter Hash Match Registers (Table 9-22)
+ * Registers: MAC_HASH0_0 through MAC_HASH7_0
+ * Registers: MAC_HASH0_1 through MAC_HASH7_1
+ * Registers: MAC_HASH0_2 through MAC_HASH7_2
+ */
+
+/* No bitfields */
+
+/*
+ * MAC Transmit Source Address Registers (Table 9-23)
+ * Register: MAC_ETHERNET_ADDR_0
+ * Register: MAC_ETHERNET_ADDR_1
+ * Register: MAC_ETHERNET_ADDR_2
+ */
+
+/* No bitfields */
+
+/*
+ * MAC Packet Type Configuration Register
+ * Register: MAC_TYPE_CFG_0
+ * Register: MAC_TYPE_CFG_1
+ * Register: MAC_TYPE_CFG_2
+ */
+
+#define S_TYPECFG_TYPESIZE	_SB_MAKE64(16)
+
+#define S_TYPECFG_TYPE0		_SB_MAKE64(0)
+#define M_TYPECFG_TYPE0		_SB_MAKEMASK(16, S_TYPECFG_TYPE0)
+#define V_TYPECFG_TYPE0(x)	_SB_MAKEVALUE(x, S_TYPECFG_TYPE0)
+#define G_TYPECFG_TYPE0(x)	_SB_GETVALUE(x, S_TYPECFG_TYPE0, M_TYPECFG_TYPE0)
+
+#define S_TYPECFG_TYPE1		_SB_MAKE64(0)
+#define M_TYPECFG_TYPE1		_SB_MAKEMASK(16, S_TYPECFG_TYPE1)
+#define V_TYPECFG_TYPE1(x)	_SB_MAKEVALUE(x, S_TYPECFG_TYPE1)
+#define G_TYPECFG_TYPE1(x)	_SB_GETVALUE(x, S_TYPECFG_TYPE1, M_TYPECFG_TYPE1)
+
+#define S_TYPECFG_TYPE2		_SB_MAKE64(0)
+#define M_TYPECFG_TYPE2		_SB_MAKEMASK(16, S_TYPECFG_TYPE2)
+#define V_TYPECFG_TYPE2(x)	_SB_MAKEVALUE(x, S_TYPECFG_TYPE2)
+#define G_TYPECFG_TYPE2(x)	_SB_GETVALUE(x, S_TYPECFG_TYPE2, M_TYPECFG_TYPE2)
+
+#define S_TYPECFG_TYPE3		_SB_MAKE64(0)
+#define M_TYPECFG_TYPE3		_SB_MAKEMASK(16, S_TYPECFG_TYPE3)
+#define V_TYPECFG_TYPE3(x)	_SB_MAKEVALUE(x, S_TYPECFG_TYPE3)
+#define G_TYPECFG_TYPE3(x)	_SB_GETVALUE(x, S_TYPECFG_TYPE3, M_TYPECFG_TYPE3)
+
+/*
+ * MAC Receive Address Filter Control Registers (Table 9-24)
+ * Register: MAC_ADFILTER_CFG_0
+ * Register: MAC_ADFILTER_CFG_1
+ * Register: MAC_ADFILTER_CFG_2
+ */
+
+#define M_MAC_ALLPKT_EN		_SB_MAKEMASK1(0)
+#define M_MAC_UCAST_EN		_SB_MAKEMASK1(1)
+#define M_MAC_UCAST_INV		_SB_MAKEMASK1(2)
+#define M_MAC_MCAST_EN		_SB_MAKEMASK1(3)
+#define M_MAC_MCAST_INV		_SB_MAKEMASK1(4)
+#define M_MAC_BCAST_EN		_SB_MAKEMASK1(5)
+#define M_MAC_DIRECT_INV	_SB_MAKEMASK1(6)
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define M_MAC_ALLMCAST_EN	_SB_MAKEMASK1(7)
+#endif /* 1250 PASS2 || 112x PASS1 || 1480 */
+
+#define S_MAC_IPHDR_OFFSET	_SB_MAKE64(8)
+#define M_MAC_IPHDR_OFFSET	_SB_MAKEMASK(8, S_MAC_IPHDR_OFFSET)
+#define V_MAC_IPHDR_OFFSET(x)	_SB_MAKEVALUE(x, S_MAC_IPHDR_OFFSET)
+#define G_MAC_IPHDR_OFFSET(x)	_SB_GETVALUE(x, S_MAC_IPHDR_OFFSET, M_MAC_IPHDR_OFFSET)
+
+#if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define S_MAC_RX_CRC_OFFSET	_SB_MAKE64(16)
+#define M_MAC_RX_CRC_OFFSET	_SB_MAKEMASK(8, S_MAC_RX_CRC_OFFSET)
+#define V_MAC_RX_CRC_OFFSET(x)	_SB_MAKEVALUE(x, S_MAC_RX_CRC_OFFSET)
+#define G_MAC_RX_CRC_OFFSET(x)	_SB_GETVALUE(x, S_MAC_RX_CRC_OFFSET, M_MAC_RX_CRC_OFFSET)
+
+#define S_MAC_RX_PKT_OFFSET	_SB_MAKE64(24)
+#define M_MAC_RX_PKT_OFFSET	_SB_MAKEMASK(8, S_MAC_RX_PKT_OFFSET)
+#define V_MAC_RX_PKT_OFFSET(x)	_SB_MAKEVALUE(x, S_MAC_RX_PKT_OFFSET)
+#define G_MAC_RX_PKT_OFFSET(x)	_SB_GETVALUE(x, S_MAC_RX_PKT_OFFSET, M_MAC_RX_PKT_OFFSET)
+
+#define M_MAC_FWDPAUSE_EN	_SB_MAKEMASK1(32)
+#define M_MAC_VLAN_DET_EN	_SB_MAKEMASK1(33)
+
+#define S_MAC_RX_CH_MSN_SEL	_SB_MAKE64(34)
+#define M_MAC_RX_CH_MSN_SEL	_SB_MAKEMASK(8, S_MAC_RX_CH_MSN_SEL)
+#define V_MAC_RX_CH_MSN_SEL(x)	_SB_MAKEVALUE(x, S_MAC_RX_CH_MSN_SEL)
+#define G_MAC_RX_CH_MSN_SEL(x)	_SB_GETVALUE(x, S_MAC_RX_CH_MSN_SEL, M_MAC_RX_CH_MSN_SEL)
+#endif /* 1250 PASS3 || 112x PASS1 || 1480 */
+
+/*
+ * MAC Receive Channel Select Registers (Table 9-25)
+ */
+
+/* no bitfields */
+
+/*
+ * MAC MII Management Interface Registers (Table 9-26)
+ * Register: MAC_MDIO_0
+ * Register: MAC_MDIO_1
+ * Register: MAC_MDIO_2
+ */
+
+#define S_MAC_MDC		0
+#define S_MAC_MDIO_DIR		1
+#define S_MAC_MDIO_OUT		2
+#define S_MAC_GENC		3
+#define S_MAC_MDIO_IN		4
+
+#define M_MAC_MDC		_SB_MAKEMASK1(S_MAC_MDC)
+#define M_MAC_MDIO_DIR		_SB_MAKEMASK1(S_MAC_MDIO_DIR)
+#define M_MAC_MDIO_DIR_INPUT	_SB_MAKEMASK1(S_MAC_MDIO_DIR)
+#define M_MAC_MDIO_OUT		_SB_MAKEMASK1(S_MAC_MDIO_OUT)
+#define M_MAC_GENC		_SB_MAKEMASK1(S_MAC_GENC)
+#define M_MAC_MDIO_IN		_SB_MAKEMASK1(S_MAC_MDIO_IN)
+
+#endif
diff --git a/arch/mips/include/asm/sibyte/sb1250_mc.h b/arch/mips/include/asm/sibyte/sb1250_mc.h
new file mode 100644
index 000000000..61411619d
--- /dev/null
+++ b/arch/mips/include/asm/sibyte/sb1250_mc.h
@@ -0,0 +1,537 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*  *********************************************************************
+    *  SB1250 Board Support Package
+    *
+    *  Memory Controller constants		File: sb1250_mc.h
+    *
+    *  This module contains constants and macros useful for
+    *  programming the memory controller.
+    *
+    *  SB1250 specification level:  User's manual 1/02/02
+    *
+    *********************************************************************
+    *
+    *  Copyright 2000, 2001, 2002, 2003
+    *  Broadcom Corporation. All rights reserved.
+    *
+    ********************************************************************* */
+
+
+#ifndef _SB1250_MC_H
+#define _SB1250_MC_H
+
+#include <asm/sibyte/sb1250_defs.h>
+
+/*
+ * Memory Channel Config Register (table 6-14)
+ */
+
+#define S_MC_RESERVED0		    0
+#define M_MC_RESERVED0		    _SB_MAKEMASK(8, S_MC_RESERVED0)
+
+#define S_MC_CHANNEL_SEL	    8
+#define M_MC_CHANNEL_SEL	    _SB_MAKEMASK(8, S_MC_CHANNEL_SEL)
+#define V_MC_CHANNEL_SEL(x)	    _SB_MAKEVALUE(x, S_MC_CHANNEL_SEL)
+#define G_MC_CHANNEL_SEL(x)	    _SB_GETVALUE(x, S_MC_CHANNEL_SEL, M_MC_CHANNEL_SEL)
+
+#define S_MC_BANK0_MAP		    16
+#define M_MC_BANK0_MAP		    _SB_MAKEMASK(4, S_MC_BANK0_MAP)
+#define V_MC_BANK0_MAP(x)	    _SB_MAKEVALUE(x, S_MC_BANK0_MAP)
+#define G_MC_BANK0_MAP(x)	    _SB_GETVALUE(x, S_MC_BANK0_MAP, M_MC_BANK0_MAP)
+
+#define K_MC_BANK0_MAP_DEFAULT	    0x00
+#define V_MC_BANK0_MAP_DEFAULT	    V_MC_BANK0_MAP(K_MC_BANK0_MAP_DEFAULT)
+
+#define S_MC_BANK1_MAP		    20
+#define M_MC_BANK1_MAP		    _SB_MAKEMASK(4, S_MC_BANK1_MAP)
+#define V_MC_BANK1_MAP(x)	    _SB_MAKEVALUE(x, S_MC_BANK1_MAP)
+#define G_MC_BANK1_MAP(x)	    _SB_GETVALUE(x, S_MC_BANK1_MAP, M_MC_BANK1_MAP)
+
+#define K_MC_BANK1_MAP_DEFAULT	    0x08
+#define V_MC_BANK1_MAP_DEFAULT	    V_MC_BANK1_MAP(K_MC_BANK1_MAP_DEFAULT)
+
+#define S_MC_BANK2_MAP		    24
+#define M_MC_BANK2_MAP		    _SB_MAKEMASK(4, S_MC_BANK2_MAP)
+#define V_MC_BANK2_MAP(x)	    _SB_MAKEVALUE(x, S_MC_BANK2_MAP)
+#define G_MC_BANK2_MAP(x)	    _SB_GETVALUE(x, S_MC_BANK2_MAP, M_MC_BANK2_MAP)
+
+#define K_MC_BANK2_MAP_DEFAULT	    0x09
+#define V_MC_BANK2_MAP_DEFAULT	    V_MC_BANK2_MAP(K_MC_BANK2_MAP_DEFAULT)
+
+#define S_MC_BANK3_MAP		    28
+#define M_MC_BANK3_MAP		    _SB_MAKEMASK(4, S_MC_BANK3_MAP)
+#define V_MC_BANK3_MAP(x)	    _SB_MAKEVALUE(x, S_MC_BANK3_MAP)
+#define G_MC_BANK3_MAP(x)	    _SB_GETVALUE(x, S_MC_BANK3_MAP, M_MC_BANK3_MAP)
+
+#define K_MC_BANK3_MAP_DEFAULT	    0x0C
+#define V_MC_BANK3_MAP_DEFAULT	    V_MC_BANK3_MAP(K_MC_BANK3_MAP_DEFAULT)
+
+#define M_MC_RESERVED1		    _SB_MAKEMASK(8, 32)
+
+#define S_MC_QUEUE_SIZE		    40
+#define M_MC_QUEUE_SIZE		    _SB_MAKEMASK(4, S_MC_QUEUE_SIZE)
+#define V_MC_QUEUE_SIZE(x)	    _SB_MAKEVALUE(x, S_MC_QUEUE_SIZE)
+#define G_MC_QUEUE_SIZE(x)	    _SB_GETVALUE(x, S_MC_QUEUE_SIZE, M_MC_QUEUE_SIZE)
+#define V_MC_QUEUE_SIZE_DEFAULT	    V_MC_QUEUE_SIZE(0x0A)
+
+#define S_MC_AGE_LIMIT		    44
+#define M_MC_AGE_LIMIT		    _SB_MAKEMASK(4, S_MC_AGE_LIMIT)
+#define V_MC_AGE_LIMIT(x)	    _SB_MAKEVALUE(x, S_MC_AGE_LIMIT)
+#define G_MC_AGE_LIMIT(x)	    _SB_GETVALUE(x, S_MC_AGE_LIMIT, M_MC_AGE_LIMIT)
+#define V_MC_AGE_LIMIT_DEFAULT	    V_MC_AGE_LIMIT(8)
+
+#define S_MC_WR_LIMIT		    48
+#define M_MC_WR_LIMIT		    _SB_MAKEMASK(4, S_MC_WR_LIMIT)
+#define V_MC_WR_LIMIT(x)	    _SB_MAKEVALUE(x, S_MC_WR_LIMIT)
+#define G_MC_WR_LIMIT(x)	    _SB_GETVALUE(x, S_MC_WR_LIMIT, M_MC_WR_LIMIT)
+#define V_MC_WR_LIMIT_DEFAULT	    V_MC_WR_LIMIT(5)
+
+#define M_MC_IOB1HIGHPRIORITY	    _SB_MAKEMASK1(52)
+
+#define M_MC_RESERVED2		    _SB_MAKEMASK(3, 53)
+
+#define S_MC_CS_MODE		    56
+#define M_MC_CS_MODE		    _SB_MAKEMASK(4, S_MC_CS_MODE)
+#define V_MC_CS_MODE(x)		    _SB_MAKEVALUE(x, S_MC_CS_MODE)
+#define G_MC_CS_MODE(x)		    _SB_GETVALUE(x, S_MC_CS_MODE, M_MC_CS_MODE)
+
+#define K_MC_CS_MODE_MSB_CS	    0
+#define K_MC_CS_MODE_INTLV_CS	    15
+#define K_MC_CS_MODE_MIXED_CS_10    12
+#define K_MC_CS_MODE_MIXED_CS_30    6
+#define K_MC_CS_MODE_MIXED_CS_32    3
+
+#define V_MC_CS_MODE_MSB_CS	    V_MC_CS_MODE(K_MC_CS_MODE_MSB_CS)
+#define V_MC_CS_MODE_INTLV_CS	    V_MC_CS_MODE(K_MC_CS_MODE_INTLV_CS)
+#define V_MC_CS_MODE_MIXED_CS_10    V_MC_CS_MODE(K_MC_CS_MODE_MIXED_CS_10)
+#define V_MC_CS_MODE_MIXED_CS_30    V_MC_CS_MODE(K_MC_CS_MODE_MIXED_CS_30)
+#define V_MC_CS_MODE_MIXED_CS_32    V_MC_CS_MODE(K_MC_CS_MODE_MIXED_CS_32)
+
+#define M_MC_ECC_DISABLE	    _SB_MAKEMASK1(60)
+#define M_MC_BERR_DISABLE	    _SB_MAKEMASK1(61)
+#define M_MC_FORCE_SEQ		    _SB_MAKEMASK1(62)
+#define M_MC_DEBUG		    _SB_MAKEMASK1(63)
+
+#define V_MC_CONFIG_DEFAULT	V_MC_WR_LIMIT_DEFAULT | V_MC_AGE_LIMIT_DEFAULT | \
+				V_MC_BANK0_MAP_DEFAULT | V_MC_BANK1_MAP_DEFAULT | \
+				V_MC_BANK2_MAP_DEFAULT | V_MC_BANK3_MAP_DEFAULT | V_MC_CHANNEL_SEL(0) | \
+				M_MC_IOB1HIGHPRIORITY | V_MC_QUEUE_SIZE_DEFAULT
+
+
+/*
+ * Memory clock config register (Table 6-15)
+ *
+ * Note: this field has been updated to be consistent with the errata to 0.2
+ */
+
+#define S_MC_CLK_RATIO		    0
+#define M_MC_CLK_RATIO		    _SB_MAKEMASK(4, S_MC_CLK_RATIO)
+#define V_MC_CLK_RATIO(x)	    _SB_MAKEVALUE(x, S_MC_CLK_RATIO)
+#define G_MC_CLK_RATIO(x)	    _SB_GETVALUE(x, S_MC_CLK_RATIO, M_MC_CLK_RATIO)
+
+#define K_MC_CLK_RATIO_2X	    4
+#define K_MC_CLK_RATIO_25X	    5
+#define K_MC_CLK_RATIO_3X	    6
+#define K_MC_CLK_RATIO_35X	    7
+#define K_MC_CLK_RATIO_4X	    8
+#define K_MC_CLK_RATIO_45X	    9
+
+#define V_MC_CLK_RATIO_2X	    V_MC_CLK_RATIO(K_MC_CLK_RATIO_2X)
+#define V_MC_CLK_RATIO_25X	    V_MC_CLK_RATIO(K_MC_CLK_RATIO_25X)
+#define V_MC_CLK_RATIO_3X	    V_MC_CLK_RATIO(K_MC_CLK_RATIO_3X)
+#define V_MC_CLK_RATIO_35X	    V_MC_CLK_RATIO(K_MC_CLK_RATIO_35X)
+#define V_MC_CLK_RATIO_4X	    V_MC_CLK_RATIO(K_MC_CLK_RATIO_4X)
+#define V_MC_CLK_RATIO_45X	    V_MC_CLK_RATIO(K_MC_CLK_RATIO_45X)
+#define V_MC_CLK_RATIO_DEFAULT	    V_MC_CLK_RATIO_25X
+
+#define S_MC_REF_RATE		     8
+#define M_MC_REF_RATE		     _SB_MAKEMASK(8, S_MC_REF_RATE)
+#define V_MC_REF_RATE(x)	     _SB_MAKEVALUE(x, S_MC_REF_RATE)
+#define G_MC_REF_RATE(x)	     _SB_GETVALUE(x, S_MC_REF_RATE, M_MC_REF_RATE)
+
+#define K_MC_REF_RATE_100MHz	     0x62
+#define K_MC_REF_RATE_133MHz	     0x81
+#define K_MC_REF_RATE_200MHz	     0xC4
+
+#define V_MC_REF_RATE_100MHz	     V_MC_REF_RATE(K_MC_REF_RATE_100MHz)
+#define V_MC_REF_RATE_133MHz	     V_MC_REF_RATE(K_MC_REF_RATE_133MHz)
+#define V_MC_REF_RATE_200MHz	     V_MC_REF_RATE(K_MC_REF_RATE_200MHz)
+#define V_MC_REF_RATE_DEFAULT	     V_MC_REF_RATE_100MHz
+
+#define S_MC_CLOCK_DRIVE	     16
+#define M_MC_CLOCK_DRIVE	     _SB_MAKEMASK(4, S_MC_CLOCK_DRIVE)
+#define V_MC_CLOCK_DRIVE(x)	     _SB_MAKEVALUE(x, S_MC_CLOCK_DRIVE)
+#define G_MC_CLOCK_DRIVE(x)	     _SB_GETVALUE(x, S_MC_CLOCK_DRIVE, M_MC_CLOCK_DRIVE)
+#define V_MC_CLOCK_DRIVE_DEFAULT     V_MC_CLOCK_DRIVE(0xF)
+
+#define S_MC_DATA_DRIVE		     20
+#define M_MC_DATA_DRIVE		     _SB_MAKEMASK(4, S_MC_DATA_DRIVE)
+#define V_MC_DATA_DRIVE(x)	     _SB_MAKEVALUE(x, S_MC_DATA_DRIVE)
+#define G_MC_DATA_DRIVE(x)	     _SB_GETVALUE(x, S_MC_DATA_DRIVE, M_MC_DATA_DRIVE)
+#define V_MC_DATA_DRIVE_DEFAULT	     V_MC_DATA_DRIVE(0x0)
+
+#define S_MC_ADDR_DRIVE		     24
+#define M_MC_ADDR_DRIVE		     _SB_MAKEMASK(4, S_MC_ADDR_DRIVE)
+#define V_MC_ADDR_DRIVE(x)	     _SB_MAKEVALUE(x, S_MC_ADDR_DRIVE)
+#define G_MC_ADDR_DRIVE(x)	     _SB_GETVALUE(x, S_MC_ADDR_DRIVE, M_MC_ADDR_DRIVE)
+#define V_MC_ADDR_DRIVE_DEFAULT	     V_MC_ADDR_DRIVE(0x0)
+
+#if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1)
+#define M_MC_REF_DISABLE	     _SB_MAKEMASK1(30)
+#endif /* 1250 PASS3 || 112x PASS1 */
+
+#define M_MC_DLL_BYPASS		     _SB_MAKEMASK1(31)
+
+#define S_MC_DQI_SKEW		    32
+#define M_MC_DQI_SKEW		    _SB_MAKEMASK(8, S_MC_DQI_SKEW)
+#define V_MC_DQI_SKEW(x)	    _SB_MAKEVALUE(x, S_MC_DQI_SKEW)
+#define G_MC_DQI_SKEW(x)	    _SB_GETVALUE(x, S_MC_DQI_SKEW, M_MC_DQI_SKEW)
+#define V_MC_DQI_SKEW_DEFAULT	    V_MC_DQI_SKEW(0)
+
+#define S_MC_DQO_SKEW		    40
+#define M_MC_DQO_SKEW		    _SB_MAKEMASK(8, S_MC_DQO_SKEW)
+#define V_MC_DQO_SKEW(x)	    _SB_MAKEVALUE(x, S_MC_DQO_SKEW)
+#define G_MC_DQO_SKEW(x)	    _SB_GETVALUE(x, S_MC_DQO_SKEW, M_MC_DQO_SKEW)
+#define V_MC_DQO_SKEW_DEFAULT	    V_MC_DQO_SKEW(0)
+
+#define S_MC_ADDR_SKEW		     48
+#define M_MC_ADDR_SKEW		     _SB_MAKEMASK(8, S_MC_ADDR_SKEW)
+#define V_MC_ADDR_SKEW(x)	     _SB_MAKEVALUE(x, S_MC_ADDR_SKEW)
+#define G_MC_ADDR_SKEW(x)	     _SB_GETVALUE(x, S_MC_ADDR_SKEW, M_MC_ADDR_SKEW)
+#define V_MC_ADDR_SKEW_DEFAULT	     V_MC_ADDR_SKEW(0x0F)
+
+#define S_MC_DLL_DEFAULT	     56
+#define M_MC_DLL_DEFAULT	     _SB_MAKEMASK(8, S_MC_DLL_DEFAULT)
+#define V_MC_DLL_DEFAULT(x)	     _SB_MAKEVALUE(x, S_MC_DLL_DEFAULT)
+#define G_MC_DLL_DEFAULT(x)	     _SB_GETVALUE(x, S_MC_DLL_DEFAULT, M_MC_DLL_DEFAULT)
+#define V_MC_DLL_DEFAULT_DEFAULT     V_MC_DLL_DEFAULT(0x10)
+
+#define V_MC_CLKCONFIG_DEFAULT	     V_MC_DLL_DEFAULT_DEFAULT |	 \
+				     V_MC_ADDR_SKEW_DEFAULT | \
+				     V_MC_DQO_SKEW_DEFAULT | \
+				     V_MC_DQI_SKEW_DEFAULT | \
+				     V_MC_ADDR_DRIVE_DEFAULT | \
+				     V_MC_DATA_DRIVE_DEFAULT | \
+				     V_MC_CLOCK_DRIVE_DEFAULT | \
+				     V_MC_REF_RATE_DEFAULT
+
+
+
+/*
+ * DRAM Command Register (Table 6-13)
+ */
+
+#define S_MC_COMMAND		    0
+#define M_MC_COMMAND		    _SB_MAKEMASK(4, S_MC_COMMAND)
+#define V_MC_COMMAND(x)		    _SB_MAKEVALUE(x, S_MC_COMMAND)
+#define G_MC_COMMAND(x)		    _SB_GETVALUE(x, S_MC_COMMAND, M_MC_COMMAND)
+
+#define K_MC_COMMAND_EMRS	    0
+#define K_MC_COMMAND_MRS	    1
+#define K_MC_COMMAND_PRE	    2
+#define K_MC_COMMAND_AR		    3
+#define K_MC_COMMAND_SETRFSH	    4
+#define K_MC_COMMAND_CLRRFSH	    5
+#define K_MC_COMMAND_SETPWRDN	    6
+#define K_MC_COMMAND_CLRPWRDN	    7
+
+#define V_MC_COMMAND_EMRS	    V_MC_COMMAND(K_MC_COMMAND_EMRS)
+#define V_MC_COMMAND_MRS	    V_MC_COMMAND(K_MC_COMMAND_MRS)
+#define V_MC_COMMAND_PRE	    V_MC_COMMAND(K_MC_COMMAND_PRE)
+#define V_MC_COMMAND_AR		    V_MC_COMMAND(K_MC_COMMAND_AR)
+#define V_MC_COMMAND_SETRFSH	    V_MC_COMMAND(K_MC_COMMAND_SETRFSH)
+#define V_MC_COMMAND_CLRRFSH	    V_MC_COMMAND(K_MC_COMMAND_CLRRFSH)
+#define V_MC_COMMAND_SETPWRDN	    V_MC_COMMAND(K_MC_COMMAND_SETPWRDN)
+#define V_MC_COMMAND_CLRPWRDN	    V_MC_COMMAND(K_MC_COMMAND_CLRPWRDN)
+
+#define M_MC_CS0		    _SB_MAKEMASK1(4)
+#define M_MC_CS1		    _SB_MAKEMASK1(5)
+#define M_MC_CS2		    _SB_MAKEMASK1(6)
+#define M_MC_CS3		    _SB_MAKEMASK1(7)
+
+/*
+ * DRAM Mode Register (Table 6-14)
+ */
+
+#define S_MC_EMODE		    0
+#define M_MC_EMODE		    _SB_MAKEMASK(15, S_MC_EMODE)
+#define V_MC_EMODE(x)		    _SB_MAKEVALUE(x, S_MC_EMODE)
+#define G_MC_EMODE(x)		    _SB_GETVALUE(x, S_MC_EMODE, M_MC_EMODE)
+#define V_MC_EMODE_DEFAULT	    V_MC_EMODE(0)
+
+#define S_MC_MODE		    16
+#define M_MC_MODE		    _SB_MAKEMASK(15, S_MC_MODE)
+#define V_MC_MODE(x)		    _SB_MAKEVALUE(x, S_MC_MODE)
+#define G_MC_MODE(x)		    _SB_GETVALUE(x, S_MC_MODE, M_MC_MODE)
+#define V_MC_MODE_DEFAULT	    V_MC_MODE(0x22)
+
+#define S_MC_DRAM_TYPE		    32
+#define M_MC_DRAM_TYPE		    _SB_MAKEMASK(3, S_MC_DRAM_TYPE)
+#define V_MC_DRAM_TYPE(x)	    _SB_MAKEVALUE(x, S_MC_DRAM_TYPE)
+#define G_MC_DRAM_TYPE(x)	    _SB_GETVALUE(x, S_MC_DRAM_TYPE, M_MC_DRAM_TYPE)
+
+#define K_MC_DRAM_TYPE_JEDEC	    0
+#define K_MC_DRAM_TYPE_FCRAM	    1
+#define K_MC_DRAM_TYPE_SGRAM	    2
+
+#define V_MC_DRAM_TYPE_JEDEC	    V_MC_DRAM_TYPE(K_MC_DRAM_TYPE_JEDEC)
+#define V_MC_DRAM_TYPE_FCRAM	    V_MC_DRAM_TYPE(K_MC_DRAM_TYPE_FCRAM)
+#define V_MC_DRAM_TYPE_SGRAM	    V_MC_DRAM_TYPE(K_MC_DRAM_TYPE_SGRAM)
+
+#define M_MC_EXTERNALDECODE	    _SB_MAKEMASK1(35)
+
+#if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1)
+#define M_MC_PRE_ON_A8		    _SB_MAKEMASK1(36)
+#define M_MC_RAM_WITH_A13	    _SB_MAKEMASK1(37)
+#endif /* 1250 PASS3 || 112x PASS1 */
+
+
+
+/*
+ * SDRAM Timing Register  (Table 6-15)
+ */
+
+#define M_MC_w2rIDLE_TWOCYCLES	  _SB_MAKEMASK1(60)
+#define M_MC_r2wIDLE_TWOCYCLES	  _SB_MAKEMASK1(61)
+#define M_MC_r2rIDLE_TWOCYCLES	  _SB_MAKEMASK1(62)
+
+#define S_MC_tFIFO		  56
+#define M_MC_tFIFO		  _SB_MAKEMASK(4, S_MC_tFIFO)
+#define V_MC_tFIFO(x)		  _SB_MAKEVALUE(x, S_MC_tFIFO)
+#define G_MC_tFIFO(x)		  _SB_GETVALUE(x, S_MC_tFIFO, M_MC_tFIFO)
+#define K_MC_tFIFO_DEFAULT	  1
+#define V_MC_tFIFO_DEFAULT	  V_MC_tFIFO(K_MC_tFIFO_DEFAULT)
+
+#define S_MC_tRFC		  52
+#define M_MC_tRFC		  _SB_MAKEMASK(4, S_MC_tRFC)
+#define V_MC_tRFC(x)		  _SB_MAKEVALUE(x, S_MC_tRFC)
+#define G_MC_tRFC(x)		  _SB_GETVALUE(x, S_MC_tRFC, M_MC_tRFC)
+#define K_MC_tRFC_DEFAULT	  12
+#define V_MC_tRFC_DEFAULT	  V_MC_tRFC(K_MC_tRFC_DEFAULT)
+
+#if SIBYTE_HDR_FEATURE(1250, PASS3)
+#define M_MC_tRFC_PLUS16	  _SB_MAKEMASK1(51)	/* 1250C3 and later.  */
+#endif
+
+#define S_MC_tCwCr		  40
+#define M_MC_tCwCr		  _SB_MAKEMASK(4, S_MC_tCwCr)
+#define V_MC_tCwCr(x)		  _SB_MAKEVALUE(x, S_MC_tCwCr)
+#define G_MC_tCwCr(x)		  _SB_GETVALUE(x, S_MC_tCwCr, M_MC_tCwCr)
+#define K_MC_tCwCr_DEFAULT	  4
+#define V_MC_tCwCr_DEFAULT	  V_MC_tCwCr(K_MC_tCwCr_DEFAULT)
+
+#define S_MC_tRCr		  28
+#define M_MC_tRCr		  _SB_MAKEMASK(4, S_MC_tRCr)
+#define V_MC_tRCr(x)		  _SB_MAKEVALUE(x, S_MC_tRCr)
+#define G_MC_tRCr(x)		  _SB_GETVALUE(x, S_MC_tRCr, M_MC_tRCr)
+#define K_MC_tRCr_DEFAULT	  9
+#define V_MC_tRCr_DEFAULT	  V_MC_tRCr(K_MC_tRCr_DEFAULT)
+
+#define S_MC_tRCw		  24
+#define M_MC_tRCw		  _SB_MAKEMASK(4, S_MC_tRCw)
+#define V_MC_tRCw(x)		  _SB_MAKEVALUE(x, S_MC_tRCw)
+#define G_MC_tRCw(x)		  _SB_GETVALUE(x, S_MC_tRCw, M_MC_tRCw)
+#define K_MC_tRCw_DEFAULT	  10
+#define V_MC_tRCw_DEFAULT	  V_MC_tRCw(K_MC_tRCw_DEFAULT)
+
+#define S_MC_tRRD		  20
+#define M_MC_tRRD		  _SB_MAKEMASK(4, S_MC_tRRD)
+#define V_MC_tRRD(x)		  _SB_MAKEVALUE(x, S_MC_tRRD)
+#define G_MC_tRRD(x)		  _SB_GETVALUE(x, S_MC_tRRD, M_MC_tRRD)
+#define K_MC_tRRD_DEFAULT	  2
+#define V_MC_tRRD_DEFAULT	  V_MC_tRRD(K_MC_tRRD_DEFAULT)
+
+#define S_MC_tRP		  16
+#define M_MC_tRP		  _SB_MAKEMASK(4, S_MC_tRP)
+#define V_MC_tRP(x)		  _SB_MAKEVALUE(x, S_MC_tRP)
+#define G_MC_tRP(x)		  _SB_GETVALUE(x, S_MC_tRP, M_MC_tRP)
+#define K_MC_tRP_DEFAULT	  4
+#define V_MC_tRP_DEFAULT	  V_MC_tRP(K_MC_tRP_DEFAULT)
+
+#define S_MC_tCwD		  8
+#define M_MC_tCwD		  _SB_MAKEMASK(4, S_MC_tCwD)
+#define V_MC_tCwD(x)		  _SB_MAKEVALUE(x, S_MC_tCwD)
+#define G_MC_tCwD(x)		  _SB_GETVALUE(x, S_MC_tCwD, M_MC_tCwD)
+#define K_MC_tCwD_DEFAULT	  1
+#define V_MC_tCwD_DEFAULT	  V_MC_tCwD(K_MC_tCwD_DEFAULT)
+
+#define M_tCrDh			  _SB_MAKEMASK1(7)
+#define M_MC_tCrDh		  M_tCrDh
+
+#define S_MC_tCrD		  4
+#define M_MC_tCrD		  _SB_MAKEMASK(3, S_MC_tCrD)
+#define V_MC_tCrD(x)		  _SB_MAKEVALUE(x, S_MC_tCrD)
+#define G_MC_tCrD(x)		  _SB_GETVALUE(x, S_MC_tCrD, M_MC_tCrD)
+#define K_MC_tCrD_DEFAULT	  2
+#define V_MC_tCrD_DEFAULT	  V_MC_tCrD(K_MC_tCrD_DEFAULT)
+
+#define S_MC_tRCD		  0
+#define M_MC_tRCD		  _SB_MAKEMASK(4, S_MC_tRCD)
+#define V_MC_tRCD(x)		  _SB_MAKEVALUE(x, S_MC_tRCD)
+#define G_MC_tRCD(x)		  _SB_GETVALUE(x, S_MC_tRCD, M_MC_tRCD)
+#define K_MC_tRCD_DEFAULT	  3
+#define V_MC_tRCD_DEFAULT	  V_MC_tRCD(K_MC_tRCD_DEFAULT)
+
+#define V_MC_TIMING_DEFAULT	V_MC_tFIFO(K_MC_tFIFO_DEFAULT) | \
+				V_MC_tRFC(K_MC_tRFC_DEFAULT) | \
+				V_MC_tCwCr(K_MC_tCwCr_DEFAULT) | \
+				V_MC_tRCr(K_MC_tRCr_DEFAULT) | \
+				V_MC_tRCw(K_MC_tRCw_DEFAULT) | \
+				V_MC_tRRD(K_MC_tRRD_DEFAULT) | \
+				V_MC_tRP(K_MC_tRP_DEFAULT) | \
+				V_MC_tCwD(K_MC_tCwD_DEFAULT) | \
+				V_MC_tCrD(K_MC_tCrD_DEFAULT) | \
+				V_MC_tRCD(K_MC_tRCD_DEFAULT) | \
+				M_MC_r2rIDLE_TWOCYCLES
+
+/*
+ * Errata says these are not the default
+ *				 M_MC_w2rIDLE_TWOCYCLES | \
+ *				 M_MC_r2wIDLE_TWOCYCLES | \
+ */
+
+
+/*
+ * Chip Select Start Address Register (Table 6-17)
+ */
+
+#define S_MC_CS0_START		    0
+#define M_MC_CS0_START		    _SB_MAKEMASK(16, S_MC_CS0_START)
+#define V_MC_CS0_START(x)	    _SB_MAKEVALUE(x, S_MC_CS0_START)
+#define G_MC_CS0_START(x)	    _SB_GETVALUE(x, S_MC_CS0_START, M_MC_CS0_START)
+
+#define S_MC_CS1_START		    16
+#define M_MC_CS1_START		    _SB_MAKEMASK(16, S_MC_CS1_START)
+#define V_MC_CS1_START(x)	    _SB_MAKEVALUE(x, S_MC_CS1_START)
+#define G_MC_CS1_START(x)	    _SB_GETVALUE(x, S_MC_CS1_START, M_MC_CS1_START)
+
+#define S_MC_CS2_START		    32
+#define M_MC_CS2_START		    _SB_MAKEMASK(16, S_MC_CS2_START)
+#define V_MC_CS2_START(x)	    _SB_MAKEVALUE(x, S_MC_CS2_START)
+#define G_MC_CS2_START(x)	    _SB_GETVALUE(x, S_MC_CS2_START, M_MC_CS2_START)
+
+#define S_MC_CS3_START		    48
+#define M_MC_CS3_START		    _SB_MAKEMASK(16, S_MC_CS3_START)
+#define V_MC_CS3_START(x)	    _SB_MAKEVALUE(x, S_MC_CS3_START)
+#define G_MC_CS3_START(x)	    _SB_GETVALUE(x, S_MC_CS3_START, M_MC_CS3_START)
+
+/*
+ * Chip Select End Address Register (Table 6-18)
+ */
+
+#define S_MC_CS0_END		    0
+#define M_MC_CS0_END		    _SB_MAKEMASK(16, S_MC_CS0_END)
+#define V_MC_CS0_END(x)		    _SB_MAKEVALUE(x, S_MC_CS0_END)
+#define G_MC_CS0_END(x)		    _SB_GETVALUE(x, S_MC_CS0_END, M_MC_CS0_END)
+
+#define S_MC_CS1_END		    16
+#define M_MC_CS1_END		    _SB_MAKEMASK(16, S_MC_CS1_END)
+#define V_MC_CS1_END(x)		    _SB_MAKEVALUE(x, S_MC_CS1_END)
+#define G_MC_CS1_END(x)		    _SB_GETVALUE(x, S_MC_CS1_END, M_MC_CS1_END)
+
+#define S_MC_CS2_END		    32
+#define M_MC_CS2_END		    _SB_MAKEMASK(16, S_MC_CS2_END)
+#define V_MC_CS2_END(x)		    _SB_MAKEVALUE(x, S_MC_CS2_END)
+#define G_MC_CS2_END(x)		    _SB_GETVALUE(x, S_MC_CS2_END, M_MC_CS2_END)
+
+#define S_MC_CS3_END		    48
+#define M_MC_CS3_END		    _SB_MAKEMASK(16, S_MC_CS3_END)
+#define V_MC_CS3_END(x)		    _SB_MAKEVALUE(x, S_MC_CS3_END)
+#define G_MC_CS3_END(x)		    _SB_GETVALUE(x, S_MC_CS3_END, M_MC_CS3_END)
+
+/*
+ * Chip Select Interleave Register (Table 6-19)
+ */
+
+#define S_MC_INTLV_RESERVED	    0
+#define M_MC_INTLV_RESERVED	    _SB_MAKEMASK(5, S_MC_INTLV_RESERVED)
+
+#define S_MC_INTERLEAVE		    7
+#define M_MC_INTERLEAVE		    _SB_MAKEMASK(18, S_MC_INTERLEAVE)
+#define V_MC_INTERLEAVE(x)	    _SB_MAKEVALUE(x, S_MC_INTERLEAVE)
+
+#define S_MC_INTLV_MBZ		    25
+#define M_MC_INTLV_MBZ		    _SB_MAKEMASK(39, S_MC_INTLV_MBZ)
+
+/*
+ * Row Address Bits Register (Table 6-20)
+ */
+
+#define S_MC_RAS_RESERVED	    0
+#define M_MC_RAS_RESERVED	    _SB_MAKEMASK(5, S_MC_RAS_RESERVED)
+
+#define S_MC_RAS_SELECT		    12
+#define M_MC_RAS_SELECT		    _SB_MAKEMASK(25, S_MC_RAS_SELECT)
+#define V_MC_RAS_SELECT(x)	    _SB_MAKEVALUE(x, S_MC_RAS_SELECT)
+
+#define S_MC_RAS_MBZ		    37
+#define M_MC_RAS_MBZ		    _SB_MAKEMASK(27, S_MC_RAS_MBZ)
+
+
+/*
+ * Column Address Bits Register (Table 6-21)
+ */
+
+#define S_MC_CAS_RESERVED	    0
+#define M_MC_CAS_RESERVED	    _SB_MAKEMASK(5, S_MC_CAS_RESERVED)
+
+#define S_MC_CAS_SELECT		    5
+#define M_MC_CAS_SELECT		    _SB_MAKEMASK(18, S_MC_CAS_SELECT)
+#define V_MC_CAS_SELECT(x)	    _SB_MAKEVALUE(x, S_MC_CAS_SELECT)
+
+#define S_MC_CAS_MBZ		    23
+#define M_MC_CAS_MBZ		    _SB_MAKEMASK(41, S_MC_CAS_MBZ)
+
+
+/*
+ * Bank Address Bits Register (Table 6-22)
+ */
+
+#define S_MC_BA_RESERVED	    0
+#define M_MC_BA_RESERVED	    _SB_MAKEMASK(5, S_MC_BA_RESERVED)
+
+#define S_MC_BA_SELECT		    5
+#define M_MC_BA_SELECT		    _SB_MAKEMASK(20, S_MC_BA_SELECT)
+#define V_MC_BA_SELECT(x)	    _SB_MAKEVALUE(x, S_MC_BA_SELECT)
+
+#define S_MC_BA_MBZ		    25
+#define M_MC_BA_MBZ		    _SB_MAKEMASK(39, S_MC_BA_MBZ)
+
+/*
+ * Chip Select Attribute Register (Table 6-23)
+ */
+
+#define K_MC_CS_ATTR_CLOSED	    0
+#define K_MC_CS_ATTR_CASCHECK	    1
+#define K_MC_CS_ATTR_HINT	    2
+#define K_MC_CS_ATTR_OPEN	    3
+
+#define S_MC_CS0_PAGE		    0
+#define M_MC_CS0_PAGE		    _SB_MAKEMASK(2, S_MC_CS0_PAGE)
+#define V_MC_CS0_PAGE(x)	    _SB_MAKEVALUE(x, S_MC_CS0_PAGE)
+#define G_MC_CS0_PAGE(x)	    _SB_GETVALUE(x, S_MC_CS0_PAGE, M_MC_CS0_PAGE)
+
+#define S_MC_CS1_PAGE		    16
+#define M_MC_CS1_PAGE		    _SB_MAKEMASK(2, S_MC_CS1_PAGE)
+#define V_MC_CS1_PAGE(x)	    _SB_MAKEVALUE(x, S_MC_CS1_PAGE)
+#define G_MC_CS1_PAGE(x)	    _SB_GETVALUE(x, S_MC_CS1_PAGE, M_MC_CS1_PAGE)
+
+#define S_MC_CS2_PAGE		    32
+#define M_MC_CS2_PAGE		    _SB_MAKEMASK(2, S_MC_CS2_PAGE)
+#define V_MC_CS2_PAGE(x)	    _SB_MAKEVALUE(x, S_MC_CS2_PAGE)
+#define G_MC_CS2_PAGE(x)	    _SB_GETVALUE(x, S_MC_CS2_PAGE, M_MC_CS2_PAGE)
+
+#define S_MC_CS3_PAGE		    48
+#define M_MC_CS3_PAGE		    _SB_MAKEMASK(2, S_MC_CS3_PAGE)
+#define V_MC_CS3_PAGE(x)	    _SB_MAKEVALUE(x, S_MC_CS3_PAGE)
+#define G_MC_CS3_PAGE(x)	    _SB_GETVALUE(x, S_MC_CS3_PAGE, M_MC_CS3_PAGE)
+
+/*
+ * ECC Test ECC Register (Table 6-25)
+ */
+
+#define S_MC_ECC_INVERT		    0
+#define M_MC_ECC_INVERT		    _SB_MAKEMASK(8, S_MC_ECC_INVERT)
+
+
+#endif
diff --git a/arch/mips/include/asm/sibyte/sb1250_regs.h b/arch/mips/include/asm/sibyte/sb1250_regs.h
new file mode 100644
index 000000000..cdac01832
--- /dev/null
+++ b/arch/mips/include/asm/sibyte/sb1250_regs.h
@@ -0,0 +1,880 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*  *********************************************************************
+    *  SB1250 Board Support Package
+    *
+    *  Register Definitions			File: sb1250_regs.h
+    *
+    *  This module contains the addresses of the on-chip peripherals
+    *  on the SB1250.
+    *
+    *  SB1250 specification level:  01/02/2002
+    *
+    *********************************************************************
+    *
+    *  Copyright 2000,2001,2002,2003
+    *  Broadcom Corporation. All rights reserved.
+    *
+    ********************************************************************* */
+
+
+#ifndef _SB1250_REGS_H
+#define _SB1250_REGS_H
+
+#include <asm/sibyte/sb1250_defs.h>
+
+
+/*  *********************************************************************
+    *  Some general notes:
+    *
+    *  For the most part, when there is more than one peripheral
+    *  of the same type on the SOC, the constants below will be
+    *  offsets from the base of each peripheral.  For example,
+    *  the MAC registers are described as offsets from the first
+    *  MAC register, and there will be a MAC_REGISTER() macro
+    *  to calculate the base address of a given MAC.
+    *
+    *  The information in this file is based on the SB1250 SOC
+    *  manual version 0.2, July 2000.
+    ********************************************************************* */
+
+
+/*  *********************************************************************
+    * Memory Controller Registers
+    ********************************************************************* */
+
+/*
+ * XXX: can't remove MC base 0 if 112x, since it's used by other macros,
+ * since there is one reg there (but it could get its addr/offset constant).
+ */
+
+#if SIBYTE_HDR_FEATURE_1250_112x		/* This MC only on 1250 & 112x */
+#define A_MC_BASE_0		    0x0010051000
+#define A_MC_BASE_1		    0x0010052000
+#define MC_REGISTER_SPACING	    0x1000
+
+#define A_MC_BASE(ctlid)	    ((ctlid)*MC_REGISTER_SPACING+A_MC_BASE_0)
+#define A_MC_REGISTER(ctlid, reg)    (A_MC_BASE(ctlid)+(reg))
+
+#define R_MC_CONFIG		    0x0000000100
+#define R_MC_DRAMCMD		    0x0000000120
+#define R_MC_DRAMMODE		    0x0000000140
+#define R_MC_TIMING1		    0x0000000160
+#define R_MC_TIMING2		    0x0000000180
+#define R_MC_CS_START		    0x00000001A0
+#define R_MC_CS_END		    0x00000001C0
+#define R_MC_CS_INTERLEAVE	    0x00000001E0
+#define S_MC_CS_STARTEND	    16
+
+#define R_MC_CSX_BASE		    0x0000000200
+#define R_MC_CSX_ROW		    0x0000000000	/* relative to CSX_BASE, above */
+#define R_MC_CSX_COL		    0x0000000020	/* relative to CSX_BASE, above */
+#define R_MC_CSX_BA		    0x0000000040	/* relative to CSX_BASE, above */
+#define MC_CSX_SPACING		    0x0000000060	/* relative to CSX_BASE, above */
+
+#define R_MC_CS0_ROW		    0x0000000200
+#define R_MC_CS0_COL		    0x0000000220
+#define R_MC_CS0_BA		    0x0000000240
+#define R_MC_CS1_ROW		    0x0000000260
+#define R_MC_CS1_COL		    0x0000000280
+#define R_MC_CS1_BA		    0x00000002A0
+#define R_MC_CS2_ROW		    0x00000002C0
+#define R_MC_CS2_COL		    0x00000002E0
+#define R_MC_CS2_BA		    0x0000000300
+#define R_MC_CS3_ROW		    0x0000000320
+#define R_MC_CS3_COL		    0x0000000340
+#define R_MC_CS3_BA		    0x0000000360
+#define R_MC_CS_ATTR		    0x0000000380
+#define R_MC_TEST_DATA		    0x0000000400
+#define R_MC_TEST_ECC		    0x0000000420
+#define R_MC_MCLK_CFG		    0x0000000500
+
+#endif	/* 1250 & 112x */
+
+/*  *********************************************************************
+    * L2 Cache Control Registers
+    ********************************************************************* */
+
+#if SIBYTE_HDR_FEATURE_1250_112x	/* This L2C only on 1250/112x */
+
+#define A_L2_READ_TAG		    0x0010040018
+#define A_L2_ECC_TAG		    0x0010040038
+#if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1)
+#define A_L2_READ_MISC		    0x0010040058
+#endif /* 1250 PASS3 || 112x PASS1 */
+#define A_L2_WAY_DISABLE	    0x0010041000
+#define A_L2_MAKEDISABLE(x)	    (A_L2_WAY_DISABLE | (((~(x))&0x0F) << 8))
+#define A_L2_MGMT_TAG_BASE	    0x00D0000000
+
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1)
+#define A_L2_CACHE_DISABLE	   0x0010042000
+#define A_L2_MAKECACHEDISABLE(x)   (A_L2_CACHE_DISABLE | (((x)&0x0F) << 8))
+#define A_L2_MISC_CONFIG	   0x0010043000
+#endif /* 1250 PASS2 || 112x PASS1 */
+
+/* Backward-compatibility definitions.	*/
+/* XXX: discourage people from using these constants.  */
+#define A_L2_READ_ADDRESS	    A_L2_READ_TAG
+#define A_L2_EEC_ADDRESS	    A_L2_ECC_TAG
+
+#endif
+
+
+/*  *********************************************************************
+    * PCI Interface Registers
+    ********************************************************************* */
+
+#if SIBYTE_HDR_FEATURE_1250_112x	/* This PCI/HT only on 1250/112x */
+#define A_PCI_TYPE00_HEADER	    0x00DE000000
+#define A_PCI_TYPE01_HEADER	    0x00DE000800
+#endif
+
+
+/*  *********************************************************************
+    * Ethernet DMA and MACs
+    ********************************************************************* */
+
+#define A_MAC_BASE_0		    0x0010064000
+#define A_MAC_BASE_1		    0x0010065000
+#if SIBYTE_HDR_FEATURE_CHIP(1250)
+#define A_MAC_BASE_2		    0x0010066000
+#endif /* 1250 */
+
+#define MAC_SPACING		    0x1000
+#define MAC_DMA_TXRX_SPACING	    0x0400
+#define MAC_DMA_CHANNEL_SPACING	    0x0100
+#define DMA_RX			    0
+#define DMA_TX			    1
+#define MAC_NUM_DMACHAN		    2		    /* channels per direction */
+
+/* XXX: not correct; depends on SOC type.  */
+#define MAC_NUM_PORTS		    3
+
+#define A_MAC_CHANNEL_BASE(macnum)		    \
+	    (A_MAC_BASE_0 +			    \
+	     MAC_SPACING*(macnum))
+
+#define A_MAC_REGISTER(macnum,reg)		    \
+	    (A_MAC_BASE_0 +			    \
+	     MAC_SPACING*(macnum) + (reg))
+
+
+#define R_MAC_DMA_CHANNELS		0x800 /* Relative to A_MAC_CHANNEL_BASE */
+
+#define A_MAC_DMA_CHANNEL_BASE(macnum, txrx, chan)  \
+	     ((A_MAC_CHANNEL_BASE(macnum)) +	    \
+	     R_MAC_DMA_CHANNELS +		    \
+	     (MAC_DMA_TXRX_SPACING*(txrx)) +	    \
+	     (MAC_DMA_CHANNEL_SPACING*(chan)))
+
+#define R_MAC_DMA_CHANNEL_BASE(txrx, chan)		\
+	     (R_MAC_DMA_CHANNELS +		     \
+	     (MAC_DMA_TXRX_SPACING*(txrx)) +	    \
+	     (MAC_DMA_CHANNEL_SPACING*(chan)))
+
+#define A_MAC_DMA_REGISTER(macnum, txrx, chan, reg)	      \
+	    (A_MAC_DMA_CHANNEL_BASE(macnum, txrx, chan) +    \
+	    (reg))
+
+#define R_MAC_DMA_REGISTER(txrx, chan, reg)	      \
+	    (R_MAC_DMA_CHANNEL_BASE(txrx, chan) +    \
+	    (reg))
+
+/*
+ * DMA channel registers, relative to A_MAC_DMA_CHANNEL_BASE
+ */
+
+#define R_MAC_DMA_CONFIG0		0x00000000
+#define R_MAC_DMA_CONFIG1		0x00000008
+#define R_MAC_DMA_DSCR_BASE		0x00000010
+#define R_MAC_DMA_DSCR_CNT		0x00000018
+#define R_MAC_DMA_CUR_DSCRA		0x00000020
+#define R_MAC_DMA_CUR_DSCRB		0x00000028
+#define R_MAC_DMA_CUR_DSCRADDR		0x00000030
+#if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1)
+#define R_MAC_DMA_OODPKTLOST_RX		0x00000038	/* rx only */
+#endif /* 1250 PASS3 || 112x PASS1 */
+
+/*
+ * RMON Counters
+ */
+
+#define R_MAC_RMON_TX_BYTES		0x00000000
+#define R_MAC_RMON_COLLISIONS		0x00000008
+#define R_MAC_RMON_LATE_COL		0x00000010
+#define R_MAC_RMON_EX_COL		0x00000018
+#define R_MAC_RMON_FCS_ERROR		0x00000020
+#define R_MAC_RMON_TX_ABORT		0x00000028
+/* Counter #6 (0x30) now reserved */
+#define R_MAC_RMON_TX_BAD		0x00000038
+#define R_MAC_RMON_TX_GOOD		0x00000040
+#define R_MAC_RMON_TX_RUNT		0x00000048
+#define R_MAC_RMON_TX_OVERSIZE		0x00000050
+#define R_MAC_RMON_RX_BYTES		0x00000080
+#define R_MAC_RMON_RX_MCAST		0x00000088
+#define R_MAC_RMON_RX_BCAST		0x00000090
+#define R_MAC_RMON_RX_BAD		0x00000098
+#define R_MAC_RMON_RX_GOOD		0x000000A0
+#define R_MAC_RMON_RX_RUNT		0x000000A8
+#define R_MAC_RMON_RX_OVERSIZE		0x000000B0
+#define R_MAC_RMON_RX_FCS_ERROR		0x000000B8
+#define R_MAC_RMON_RX_LENGTH_ERROR	0x000000C0
+#define R_MAC_RMON_RX_CODE_ERROR	0x000000C8
+#define R_MAC_RMON_RX_ALIGN_ERROR	0x000000D0
+
+/* Updated to spec 0.2 */
+#define R_MAC_CFG			0x00000100
+#define R_MAC_THRSH_CFG			0x00000108
+#define R_MAC_VLANTAG			0x00000110
+#define R_MAC_FRAMECFG			0x00000118
+#define R_MAC_EOPCNT			0x00000120
+#define R_MAC_FIFO_PTRS			0x00000128
+#define R_MAC_ADFILTER_CFG		0x00000200
+#define R_MAC_ETHERNET_ADDR		0x00000208
+#define R_MAC_PKT_TYPE			0x00000210
+#if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define R_MAC_ADMASK0			0x00000218
+#define R_MAC_ADMASK1			0x00000220
+#endif /* 1250 PASS3 || 112x PASS1 || 1480 */
+#define R_MAC_HASH_BASE			0x00000240
+#define R_MAC_ADDR_BASE			0x00000280
+#define R_MAC_CHLO0_BASE		0x00000300
+#define R_MAC_CHUP0_BASE		0x00000320
+#define R_MAC_ENABLE			0x00000400
+#define R_MAC_STATUS			0x00000408
+#define R_MAC_INT_MASK			0x00000410
+#define R_MAC_TXD_CTL			0x00000420
+#define R_MAC_MDIO			0x00000428
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define R_MAC_STATUS1			0x00000430
+#endif /* 1250 PASS2 || 112x PASS1 || 1480 */
+#define R_MAC_DEBUG_STATUS		0x00000448
+
+#define MAC_HASH_COUNT			8
+#define MAC_ADDR_COUNT			8
+#define MAC_CHMAP_COUNT			4
+
+
+/*  *********************************************************************
+    * DUART Registers
+    ********************************************************************* */
+
+
+#if SIBYTE_HDR_FEATURE_1250_112x    /* This MC only on 1250 & 112x */
+#define R_DUART_NUM_PORTS	    2
+
+#define A_DUART			    0x0010060000
+
+#define DUART_CHANREG_SPACING	    0x100
+
+#define A_DUART_CHANREG(chan, reg)					\
+	(A_DUART + DUART_CHANREG_SPACING * ((chan) + 1) + (reg))
+#endif	/* 1250 & 112x */
+
+#define R_DUART_MODE_REG_1	    0x000
+#define R_DUART_MODE_REG_2	    0x010
+#define R_DUART_STATUS		    0x020
+#define R_DUART_CLK_SEL		    0x030
+#define R_DUART_CMD		    0x050
+#define R_DUART_RX_HOLD		    0x060
+#define R_DUART_TX_HOLD		    0x070
+
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define R_DUART_FULL_CTL	    0x040
+#define R_DUART_OPCR_X		    0x080
+#define R_DUART_AUXCTL_X	    0x090
+#endif /* 1250 PASS2 || 112x PASS1 || 1480 */
+
+
+/*
+ * The IMR and ISR can't be addressed with A_DUART_CHANREG,
+ * so use these macros instead.
+ */
+
+#if SIBYTE_HDR_FEATURE_1250_112x    /* This MC only on 1250 & 112x */
+#define DUART_IMRISR_SPACING	    0x20
+#define DUART_INCHNG_SPACING	    0x10
+
+#define A_DUART_CTRLREG(reg)						\
+	(A_DUART + DUART_CHANREG_SPACING * 3 + (reg))
+
+#define R_DUART_IMRREG(chan)						\
+	(R_DUART_IMR_A + (chan) * DUART_IMRISR_SPACING)
+#define R_DUART_ISRREG(chan)						\
+	(R_DUART_ISR_A + (chan) * DUART_IMRISR_SPACING)
+#define R_DUART_INCHREG(chan)						\
+	(R_DUART_IN_CHNG_A + (chan) * DUART_INCHNG_SPACING)
+
+#define A_DUART_IMRREG(chan)	    A_DUART_CTRLREG(R_DUART_IMRREG(chan))
+#define A_DUART_ISRREG(chan)	    A_DUART_CTRLREG(R_DUART_ISRREG(chan))
+#define A_DUART_INCHREG(chan)	    A_DUART_CTRLREG(R_DUART_INCHREG(chan))
+#endif	/* 1250 & 112x */
+
+#define R_DUART_AUX_CTRL	    0x010
+#define R_DUART_ISR_A		    0x020
+#define R_DUART_IMR_A		    0x030
+#define R_DUART_ISR_B		    0x040
+#define R_DUART_IMR_B		    0x050
+#define R_DUART_OUT_PORT	    0x060
+#define R_DUART_OPCR		    0x070
+#define R_DUART_IN_PORT		    0x080
+
+#define R_DUART_SET_OPR		    0x0B0
+#define R_DUART_CLEAR_OPR	    0x0C0
+#define R_DUART_IN_CHNG_A	    0x0D0
+#define R_DUART_IN_CHNG_B	    0x0E0
+
+
+/*
+ * These constants are the absolute addresses.
+ */
+
+#define A_DUART_MODE_REG_1_A	    0x0010060100
+#define A_DUART_MODE_REG_2_A	    0x0010060110
+#define A_DUART_STATUS_A	    0x0010060120
+#define A_DUART_CLK_SEL_A	    0x0010060130
+#define A_DUART_CMD_A		    0x0010060150
+#define A_DUART_RX_HOLD_A	    0x0010060160
+#define A_DUART_TX_HOLD_A	    0x0010060170
+
+#define A_DUART_MODE_REG_1_B	    0x0010060200
+#define A_DUART_MODE_REG_2_B	    0x0010060210
+#define A_DUART_STATUS_B	    0x0010060220
+#define A_DUART_CLK_SEL_B	    0x0010060230
+#define A_DUART_CMD_B		    0x0010060250
+#define A_DUART_RX_HOLD_B	    0x0010060260
+#define A_DUART_TX_HOLD_B	    0x0010060270
+
+#define A_DUART_INPORT_CHNG	    0x0010060300
+#define A_DUART_AUX_CTRL	    0x0010060310
+#define A_DUART_ISR_A		    0x0010060320
+#define A_DUART_IMR_A		    0x0010060330
+#define A_DUART_ISR_B		    0x0010060340
+#define A_DUART_IMR_B		    0x0010060350
+#define A_DUART_OUT_PORT	    0x0010060360
+#define A_DUART_OPCR		    0x0010060370
+#define A_DUART_IN_PORT		    0x0010060380
+#define A_DUART_ISR		    0x0010060390
+#define A_DUART_IMR		    0x00100603A0
+#define A_DUART_SET_OPR		    0x00100603B0
+#define A_DUART_CLEAR_OPR	    0x00100603C0
+#define A_DUART_INPORT_CHNG_A	    0x00100603D0
+#define A_DUART_INPORT_CHNG_B	    0x00100603E0
+
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1)
+#define A_DUART_FULL_CTL_A	    0x0010060140
+#define A_DUART_FULL_CTL_B	    0x0010060240
+
+#define A_DUART_OPCR_A		    0x0010060180
+#define A_DUART_OPCR_B		    0x0010060280
+
+#define A_DUART_INPORT_CHNG_DEBUG   0x00100603F0
+#endif /* 1250 PASS2 || 112x PASS1 */
+
+
+/*  *********************************************************************
+    * Synchronous Serial Registers
+    ********************************************************************* */
+
+
+#if SIBYTE_HDR_FEATURE_1250_112x	/* sync serial only on 1250/112x */
+
+#define A_SER_BASE_0		    0x0010060400
+#define A_SER_BASE_1		    0x0010060800
+#define SER_SPACING		    0x400
+
+#define SER_DMA_TXRX_SPACING	    0x80
+
+#define SER_NUM_PORTS		    2
+
+#define A_SER_CHANNEL_BASE(sernum)		    \
+	    (A_SER_BASE_0 +			    \
+	     SER_SPACING*(sernum))
+
+#define A_SER_REGISTER(sernum,reg)		    \
+	    (A_SER_BASE_0 +			    \
+	     SER_SPACING*(sernum) + (reg))
+
+
+#define R_SER_DMA_CHANNELS		0   /* Relative to A_SER_BASE_x */
+
+#define A_SER_DMA_CHANNEL_BASE(sernum,txrx)    \
+	     ((A_SER_CHANNEL_BASE(sernum)) +	    \
+	     R_SER_DMA_CHANNELS +		    \
+	     (SER_DMA_TXRX_SPACING*(txrx)))
+
+#define A_SER_DMA_REGISTER(sernum, txrx, reg)		\
+	    (A_SER_DMA_CHANNEL_BASE(sernum, txrx) +    \
+	    (reg))
+
+
+/*
+ * DMA channel registers, relative to A_SER_DMA_CHANNEL_BASE
+ */
+
+#define R_SER_DMA_CONFIG0	    0x00000000
+#define R_SER_DMA_CONFIG1	    0x00000008
+#define R_SER_DMA_DSCR_BASE	    0x00000010
+#define R_SER_DMA_DSCR_CNT	    0x00000018
+#define R_SER_DMA_CUR_DSCRA	    0x00000020
+#define R_SER_DMA_CUR_DSCRB	    0x00000028
+#define R_SER_DMA_CUR_DSCRADDR	    0x00000030
+
+#define R_SER_DMA_CONFIG0_RX	    0x00000000
+#define R_SER_DMA_CONFIG1_RX	    0x00000008
+#define R_SER_DMA_DSCR_BASE_RX	    0x00000010
+#define R_SER_DMA_DSCR_COUNT_RX	    0x00000018
+#define R_SER_DMA_CUR_DSCR_A_RX	    0x00000020
+#define R_SER_DMA_CUR_DSCR_B_RX	    0x00000028
+#define R_SER_DMA_CUR_DSCR_ADDR_RX  0x00000030
+
+#define R_SER_DMA_CONFIG0_TX	    0x00000080
+#define R_SER_DMA_CONFIG1_TX	    0x00000088
+#define R_SER_DMA_DSCR_BASE_TX	    0x00000090
+#define R_SER_DMA_DSCR_COUNT_TX	    0x00000098
+#define R_SER_DMA_CUR_DSCR_A_TX	    0x000000A0
+#define R_SER_DMA_CUR_DSCR_B_TX	    0x000000A8
+#define R_SER_DMA_CUR_DSCR_ADDR_TX  0x000000B0
+
+#define R_SER_MODE		    0x00000100
+#define R_SER_MINFRM_SZ		    0x00000108
+#define R_SER_MAXFRM_SZ		    0x00000110
+#define R_SER_ADDR		    0x00000118
+#define R_SER_USR0_ADDR		    0x00000120
+#define R_SER_USR1_ADDR		    0x00000128
+#define R_SER_USR2_ADDR		    0x00000130
+#define R_SER_USR3_ADDR		    0x00000138
+#define R_SER_CMD		    0x00000140
+#define R_SER_TX_RD_THRSH	    0x00000160
+#define R_SER_TX_WR_THRSH	    0x00000168
+#define R_SER_RX_RD_THRSH	    0x00000170
+#define R_SER_LINE_MODE		    0x00000178
+#define R_SER_DMA_ENABLE	    0x00000180
+#define R_SER_INT_MASK		    0x00000190
+#define R_SER_STATUS		    0x00000188
+#define R_SER_STATUS_DEBUG	    0x000001A8
+#define R_SER_RX_TABLE_BASE	    0x00000200
+#define SER_RX_TABLE_COUNT	    16
+#define R_SER_TX_TABLE_BASE	    0x00000300
+#define SER_TX_TABLE_COUNT	    16
+
+/* RMON Counters */
+#define R_SER_RMON_TX_BYTE_LO	    0x000001C0
+#define R_SER_RMON_TX_BYTE_HI	    0x000001C8
+#define R_SER_RMON_RX_BYTE_LO	    0x000001D0
+#define R_SER_RMON_RX_BYTE_HI	    0x000001D8
+#define R_SER_RMON_TX_UNDERRUN	    0x000001E0
+#define R_SER_RMON_RX_OVERFLOW	    0x000001E8
+#define R_SER_RMON_RX_ERRORS	    0x000001F0
+#define R_SER_RMON_RX_BADADDR	    0x000001F8
+
+#endif	/* 1250/112x */
+
+/*  *********************************************************************
+    * Generic Bus Registers
+    ********************************************************************* */
+
+#define IO_EXT_CFG_COUNT	    8
+
+#define A_IO_EXT_BASE		    0x0010061000
+#define A_IO_EXT_REG(r)		    (A_IO_EXT_BASE + (r))
+
+#define A_IO_EXT_CFG_BASE	    0x0010061000
+#define A_IO_EXT_MULT_SIZE_BASE	    0x0010061100
+#define A_IO_EXT_START_ADDR_BASE    0x0010061200
+#define A_IO_EXT_TIME_CFG0_BASE	    0x0010061600
+#define A_IO_EXT_TIME_CFG1_BASE	    0x0010061700
+
+#define IO_EXT_REGISTER_SPACING	    8
+#define A_IO_EXT_CS_BASE(cs)	    (A_IO_EXT_CFG_BASE+IO_EXT_REGISTER_SPACING*(cs))
+#define R_IO_EXT_REG(reg, cs)	    ((cs)*IO_EXT_REGISTER_SPACING + (reg))
+
+#define R_IO_EXT_CFG		    0x0000
+#define R_IO_EXT_MULT_SIZE	    0x0100
+#define R_IO_EXT_START_ADDR	    0x0200
+#define R_IO_EXT_TIME_CFG0	    0x0600
+#define R_IO_EXT_TIME_CFG1	    0x0700
+
+
+#define A_IO_INTERRUPT_STATUS	    0x0010061A00
+#define A_IO_INTERRUPT_DATA0	    0x0010061A10
+#define A_IO_INTERRUPT_DATA1	    0x0010061A18
+#define A_IO_INTERRUPT_DATA2	    0x0010061A20
+#define A_IO_INTERRUPT_DATA3	    0x0010061A28
+#define A_IO_INTERRUPT_ADDR0	    0x0010061A30
+#define A_IO_INTERRUPT_ADDR1	    0x0010061A40
+#define A_IO_INTERRUPT_PARITY	    0x0010061A50
+#define A_IO_PCMCIA_CFG		    0x0010061A60
+#define A_IO_PCMCIA_STATUS	    0x0010061A70
+#define A_IO_DRIVE_0		    0x0010061300
+#define A_IO_DRIVE_1		    0x0010061308
+#define A_IO_DRIVE_2		    0x0010061310
+#define A_IO_DRIVE_3		    0x0010061318
+#define A_IO_DRIVE_BASE		    A_IO_DRIVE_0
+#define IO_DRIVE_REGISTER_SPACING   8
+#define R_IO_DRIVE(x)		    ((x)*IO_DRIVE_REGISTER_SPACING)
+#define A_IO_DRIVE(x)		    (A_IO_DRIVE_BASE + R_IO_DRIVE(x))
+
+#define R_IO_INTERRUPT_STATUS	    0x0A00
+#define R_IO_INTERRUPT_DATA0	    0x0A10
+#define R_IO_INTERRUPT_DATA1	    0x0A18
+#define R_IO_INTERRUPT_DATA2	    0x0A20
+#define R_IO_INTERRUPT_DATA3	    0x0A28
+#define R_IO_INTERRUPT_ADDR0	    0x0A30
+#define R_IO_INTERRUPT_ADDR1	    0x0A40
+#define R_IO_INTERRUPT_PARITY	    0x0A50
+#define R_IO_PCMCIA_CFG		    0x0A60
+#define R_IO_PCMCIA_STATUS	    0x0A70
+
+/*  *********************************************************************
+    * GPIO Registers
+    ********************************************************************* */
+
+#define A_GPIO_CLR_EDGE		    0x0010061A80
+#define A_GPIO_INT_TYPE		    0x0010061A88
+#define A_GPIO_INPUT_INVERT	    0x0010061A90
+#define A_GPIO_GLITCH		    0x0010061A98
+#define A_GPIO_READ		    0x0010061AA0
+#define A_GPIO_DIRECTION	    0x0010061AA8
+#define A_GPIO_PIN_CLR		    0x0010061AB0
+#define A_GPIO_PIN_SET		    0x0010061AB8
+
+#define A_GPIO_BASE		    0x0010061A80
+
+#define R_GPIO_CLR_EDGE		    0x00
+#define R_GPIO_INT_TYPE		    0x08
+#define R_GPIO_INPUT_INVERT	    0x10
+#define R_GPIO_GLITCH		    0x18
+#define R_GPIO_READ		    0x20
+#define R_GPIO_DIRECTION	    0x28
+#define R_GPIO_PIN_CLR		    0x30
+#define R_GPIO_PIN_SET		    0x38
+
+/*  *********************************************************************
+    * SMBus Registers
+    ********************************************************************* */
+
+#define A_SMB_XTRA_0		    0x0010060000
+#define A_SMB_XTRA_1		    0x0010060008
+#define A_SMB_FREQ_0		    0x0010060010
+#define A_SMB_FREQ_1		    0x0010060018
+#define A_SMB_STATUS_0		    0x0010060020
+#define A_SMB_STATUS_1		    0x0010060028
+#define A_SMB_CMD_0		    0x0010060030
+#define A_SMB_CMD_1		    0x0010060038
+#define A_SMB_START_0		    0x0010060040
+#define A_SMB_START_1		    0x0010060048
+#define A_SMB_DATA_0		    0x0010060050
+#define A_SMB_DATA_1		    0x0010060058
+#define A_SMB_CONTROL_0		    0x0010060060
+#define A_SMB_CONTROL_1		    0x0010060068
+#define A_SMB_PEC_0		    0x0010060070
+#define A_SMB_PEC_1		    0x0010060078
+
+#define A_SMB_0			    0x0010060000
+#define A_SMB_1			    0x0010060008
+#define SMB_REGISTER_SPACING	    0x8
+#define A_SMB_BASE(idx)		    (A_SMB_0+(idx)*SMB_REGISTER_SPACING)
+#define A_SMB_REGISTER(idx, reg)    (A_SMB_BASE(idx)+(reg))
+
+#define R_SMB_XTRA		    0x0000000000
+#define R_SMB_FREQ		    0x0000000010
+#define R_SMB_STATUS		    0x0000000020
+#define R_SMB_CMD		    0x0000000030
+#define R_SMB_START		    0x0000000040
+#define R_SMB_DATA		    0x0000000050
+#define R_SMB_CONTROL		    0x0000000060
+#define R_SMB_PEC		    0x0000000070
+
+/*  *********************************************************************
+    * Timer Registers
+    ********************************************************************* */
+
+/*
+ * Watchdog timers
+ */
+
+#define A_SCD_WDOG_0		    0x0010020050
+#define A_SCD_WDOG_1		    0x0010020150
+#define SCD_WDOG_SPACING	    0x100
+#define SCD_NUM_WDOGS		    2
+#define A_SCD_WDOG_BASE(w)	    (A_SCD_WDOG_0+SCD_WDOG_SPACING*(w))
+#define A_SCD_WDOG_REGISTER(w, r)   (A_SCD_WDOG_BASE(w) + (r))
+
+#define R_SCD_WDOG_INIT		    0x0000000000
+#define R_SCD_WDOG_CNT		    0x0000000008
+#define R_SCD_WDOG_CFG		    0x0000000010
+
+#define A_SCD_WDOG_INIT_0	    0x0010020050
+#define A_SCD_WDOG_CNT_0	    0x0010020058
+#define A_SCD_WDOG_CFG_0	    0x0010020060
+
+#define A_SCD_WDOG_INIT_1	    0x0010020150
+#define A_SCD_WDOG_CNT_1	    0x0010020158
+#define A_SCD_WDOG_CFG_1	    0x0010020160
+
+/*
+ * Generic timers
+ */
+
+#define A_SCD_TIMER_0		    0x0010020070
+#define A_SCD_TIMER_1		    0x0010020078
+#define A_SCD_TIMER_2		    0x0010020170
+#define A_SCD_TIMER_3		    0x0010020178
+#define SCD_NUM_TIMERS		    4
+#define A_SCD_TIMER_BASE(w)	    (A_SCD_TIMER_0+0x08*((w)&1)+0x100*(((w)&2)>>1))
+#define A_SCD_TIMER_REGISTER(w, r)  (A_SCD_TIMER_BASE(w) + (r))
+
+#define R_SCD_TIMER_INIT	    0x0000000000
+#define R_SCD_TIMER_CNT		    0x0000000010
+#define R_SCD_TIMER_CFG		    0x0000000020
+
+#define A_SCD_TIMER_INIT_0	    0x0010020070
+#define A_SCD_TIMER_CNT_0	    0x0010020080
+#define A_SCD_TIMER_CFG_0	    0x0010020090
+
+#define A_SCD_TIMER_INIT_1	    0x0010020078
+#define A_SCD_TIMER_CNT_1	    0x0010020088
+#define A_SCD_TIMER_CFG_1	    0x0010020098
+
+#define A_SCD_TIMER_INIT_2	    0x0010020170
+#define A_SCD_TIMER_CNT_2	    0x0010020180
+#define A_SCD_TIMER_CFG_2	    0x0010020190
+
+#define A_SCD_TIMER_INIT_3	    0x0010020178
+#define A_SCD_TIMER_CNT_3	    0x0010020188
+#define A_SCD_TIMER_CFG_3	    0x0010020198
+
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1)
+#define A_SCD_SCRATCH		   0x0010020C10
+#endif /* 1250 PASS2 || 112x PASS1 */
+
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define A_SCD_ZBBUS_CYCLE_COUNT	   0x0010030000
+#define A_SCD_ZBBUS_CYCLE_CP0	   0x0010020C00
+#define A_SCD_ZBBUS_CYCLE_CP1	   0x0010020C08
+#endif
+
+/*  *********************************************************************
+    * System Control Registers
+    ********************************************************************* */
+
+#define A_SCD_SYSTEM_REVISION	    0x0010020000
+#define A_SCD_SYSTEM_CFG	    0x0010020008
+#define A_SCD_SYSTEM_MANUF	    0x0010038000
+
+/*  *********************************************************************
+    * System Address Trap Registers
+    ********************************************************************* */
+
+#define A_ADDR_TRAP_INDEX	    0x00100200B0
+#define A_ADDR_TRAP_REG		    0x00100200B8
+#define A_ADDR_TRAP_UP_0	    0x0010020400
+#define A_ADDR_TRAP_UP_1	    0x0010020408
+#define A_ADDR_TRAP_UP_2	    0x0010020410
+#define A_ADDR_TRAP_UP_3	    0x0010020418
+#define A_ADDR_TRAP_DOWN_0	    0x0010020420
+#define A_ADDR_TRAP_DOWN_1	    0x0010020428
+#define A_ADDR_TRAP_DOWN_2	    0x0010020430
+#define A_ADDR_TRAP_DOWN_3	    0x0010020438
+#define A_ADDR_TRAP_CFG_0	    0x0010020440
+#define A_ADDR_TRAP_CFG_1	    0x0010020448
+#define A_ADDR_TRAP_CFG_2	    0x0010020450
+#define A_ADDR_TRAP_CFG_3	    0x0010020458
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define A_ADDR_TRAP_REG_DEBUG	    0x0010020460
+#endif /* 1250 PASS2 || 112x PASS1 || 1480 */
+
+#define ADDR_TRAP_SPACING 8
+#define NUM_ADDR_TRAP 4
+#define A_ADDR_TRAP_UP(n) (A_ADDR_TRAP_UP_0 + ((n) * ADDR_TRAP_SPACING))
+#define A_ADDR_TRAP_DOWN(n) (A_ADDR_TRAP_DOWN_0 + ((n) * ADDR_TRAP_SPACING))
+#define A_ADDR_TRAP_CFG(n) (A_ADDR_TRAP_CFG_0 + ((n) * ADDR_TRAP_SPACING))
+
+
+/*  *********************************************************************
+    * System Interrupt Mapper Registers
+    ********************************************************************* */
+
+#define A_IMR_CPU0_BASE			0x0010020000
+#define A_IMR_CPU1_BASE			0x0010022000
+#define IMR_REGISTER_SPACING		0x2000
+#define IMR_REGISTER_SPACING_SHIFT	13
+
+#define A_IMR_MAPPER(cpu) (A_IMR_CPU0_BASE+(cpu)*IMR_REGISTER_SPACING)
+#define A_IMR_REGISTER(cpu, reg) (A_IMR_MAPPER(cpu)+(reg))
+
+#define R_IMR_INTERRUPT_DIAG		0x0010
+#define R_IMR_INTERRUPT_LDT		0x0018
+#define R_IMR_INTERRUPT_MASK		0x0028
+#define R_IMR_INTERRUPT_TRACE		0x0038
+#define R_IMR_INTERRUPT_SOURCE_STATUS	0x0040
+#define R_IMR_LDT_INTERRUPT_SET		0x0048
+#define R_IMR_LDT_INTERRUPT		0x0018
+#define R_IMR_LDT_INTERRUPT_CLR		0x0020
+#define R_IMR_MAILBOX_CPU		0x00c0
+#define R_IMR_ALIAS_MAILBOX_CPU		0x1000
+#define R_IMR_MAILBOX_SET_CPU		0x00C8
+#define R_IMR_ALIAS_MAILBOX_SET_CPU	0x1008
+#define R_IMR_MAILBOX_CLR_CPU		0x00D0
+#define R_IMR_INTERRUPT_STATUS_BASE	0x0100
+#define R_IMR_INTERRUPT_STATUS_COUNT	7
+#define R_IMR_INTERRUPT_MAP_BASE	0x0200
+#define R_IMR_INTERRUPT_MAP_COUNT	64
+
+/*
+ * these macros work together to build the address of a mailbox
+ * register, e.g., A_MAILBOX_REGISTER(R_IMR_MAILBOX_SET_CPU,1)
+ * for mbox_0_set_cpu2 returns 0x00100240C8
+ */
+#define A_MAILBOX_REGISTER(reg,cpu) \
+    (A_IMR_CPU0_BASE + (cpu * IMR_REGISTER_SPACING) + reg)
+
+/*  *********************************************************************
+    * System Performance Counter Registers
+    ********************************************************************* */
+
+#define A_SCD_PERF_CNT_CFG	    0x00100204C0
+#define A_SCD_PERF_CNT_0	    0x00100204D0
+#define A_SCD_PERF_CNT_1	    0x00100204D8
+#define A_SCD_PERF_CNT_2	    0x00100204E0
+#define A_SCD_PERF_CNT_3	    0x00100204E8
+
+#define SCD_NUM_PERF_CNT 4
+#define SCD_PERF_CNT_SPACING 8
+#define A_SCD_PERF_CNT(n) (A_SCD_PERF_CNT_0+(n*SCD_PERF_CNT_SPACING))
+
+/*  *********************************************************************
+    * System Bus Watcher Registers
+    ********************************************************************* */
+
+#define A_SCD_BUS_ERR_STATUS	    0x0010020880
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1)
+#define A_SCD_BUS_ERR_STATUS_DEBUG  0x00100208D0
+#define A_BUS_ERR_STATUS_DEBUG	0x00100208D0
+#endif /* 1250 PASS2 || 112x PASS1 */
+#define A_BUS_ERR_DATA_0	    0x00100208A0
+#define A_BUS_ERR_DATA_1	    0x00100208A8
+#define A_BUS_ERR_DATA_2	    0x00100208B0
+#define A_BUS_ERR_DATA_3	    0x00100208B8
+#define A_BUS_L2_ERRORS		    0x00100208C0
+#define A_BUS_MEM_IO_ERRORS	    0x00100208C8
+
+/*  *********************************************************************
+    * System Debug Controller Registers
+    ********************************************************************* */
+
+#define A_SCD_JTAG_BASE		    0x0010000000
+
+/*  *********************************************************************
+    * System Trace Buffer Registers
+    ********************************************************************* */
+
+#define A_SCD_TRACE_CFG		    0x0010020A00
+#define A_SCD_TRACE_READ	    0x0010020A08
+#define A_SCD_TRACE_EVENT_0	    0x0010020A20
+#define A_SCD_TRACE_EVENT_1	    0x0010020A28
+#define A_SCD_TRACE_EVENT_2	    0x0010020A30
+#define A_SCD_TRACE_EVENT_3	    0x0010020A38
+#define A_SCD_TRACE_SEQUENCE_0	    0x0010020A40
+#define A_SCD_TRACE_SEQUENCE_1	    0x0010020A48
+#define A_SCD_TRACE_SEQUENCE_2	    0x0010020A50
+#define A_SCD_TRACE_SEQUENCE_3	    0x0010020A58
+#define A_SCD_TRACE_EVENT_4	    0x0010020A60
+#define A_SCD_TRACE_EVENT_5	    0x0010020A68
+#define A_SCD_TRACE_EVENT_6	    0x0010020A70
+#define A_SCD_TRACE_EVENT_7	    0x0010020A78
+#define A_SCD_TRACE_SEQUENCE_4	    0x0010020A80
+#define A_SCD_TRACE_SEQUENCE_5	    0x0010020A88
+#define A_SCD_TRACE_SEQUENCE_6	    0x0010020A90
+#define A_SCD_TRACE_SEQUENCE_7	    0x0010020A98
+
+#define TRACE_REGISTER_SPACING 8
+#define TRACE_NUM_REGISTERS    8
+#define A_SCD_TRACE_EVENT(n) (((n) & 4) ? \
+   (A_SCD_TRACE_EVENT_4 + (((n) & 3) * TRACE_REGISTER_SPACING)) : \
+   (A_SCD_TRACE_EVENT_0 + ((n) * TRACE_REGISTER_SPACING)))
+#define A_SCD_TRACE_SEQUENCE(n) (((n) & 4) ? \
+   (A_SCD_TRACE_SEQUENCE_4 + (((n) & 3) * TRACE_REGISTER_SPACING)) : \
+   (A_SCD_TRACE_SEQUENCE_0 + ((n) * TRACE_REGISTER_SPACING)))
+
+/*  *********************************************************************
+    * System Generic DMA Registers
+    ********************************************************************* */
+
+#define A_DM_0			    0x0010020B00
+#define A_DM_1			    0x0010020B20
+#define A_DM_2			    0x0010020B40
+#define A_DM_3			    0x0010020B60
+#define DM_REGISTER_SPACING	    0x20
+#define DM_NUM_CHANNELS		    4
+#define A_DM_BASE(idx) (A_DM_0 + ((idx) * DM_REGISTER_SPACING))
+#define A_DM_REGISTER(idx, reg) (A_DM_BASE(idx) + (reg))
+
+#define R_DM_DSCR_BASE		    0x0000000000
+#define R_DM_DSCR_COUNT		    0x0000000008
+#define R_DM_CUR_DSCR_ADDR	    0x0000000010
+#define R_DM_DSCR_BASE_DEBUG	    0x0000000018
+
+#if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1)
+#define A_DM_PARTIAL_0		    0x0010020ba0
+#define A_DM_PARTIAL_1		    0x0010020ba8
+#define A_DM_PARTIAL_2		    0x0010020bb0
+#define A_DM_PARTIAL_3		    0x0010020bb8
+#define DM_PARTIAL_REGISTER_SPACING 0x8
+#define A_DM_PARTIAL(idx)	    (A_DM_PARTIAL_0 + ((idx) * DM_PARTIAL_REGISTER_SPACING))
+#endif /* 1250 PASS3 || 112x PASS1 */
+
+#if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1)
+#define A_DM_CRC_0		    0x0010020b80
+#define A_DM_CRC_1		    0x0010020b90
+#define DM_CRC_REGISTER_SPACING	    0x10
+#define DM_CRC_NUM_CHANNELS	    2
+#define A_DM_CRC_BASE(idx)	    (A_DM_CRC_0 + ((idx) * DM_CRC_REGISTER_SPACING))
+#define A_DM_CRC_REGISTER(idx, reg)  (A_DM_CRC_BASE(idx) + (reg))
+
+#define R_CRC_DEF_0		    0x00
+#define R_CTCP_DEF_0		    0x08
+#endif /* 1250 PASS3 || 112x PASS1 */
+
+/*  *********************************************************************
+    *  Physical Address Map
+    ********************************************************************* */
+
+#if SIBYTE_HDR_FEATURE_1250_112x
+#define A_PHYS_MEMORY_0			_SB_MAKE64(0x0000000000)
+#define A_PHYS_MEMORY_SIZE		_SB_MAKE64((256*1024*1024))
+#define A_PHYS_SYSTEM_CTL		_SB_MAKE64(0x0010000000)
+#define A_PHYS_IO_SYSTEM		_SB_MAKE64(0x0010060000)
+#define A_PHYS_GENBUS			_SB_MAKE64(0x0010090000)
+#define A_PHYS_GENBUS_END		_SB_MAKE64(0x0040000000)
+#define A_PHYS_LDTPCI_IO_MATCH_BYTES_32 _SB_MAKE64(0x0040000000)
+#define A_PHYS_LDTPCI_IO_MATCH_BITS_32	_SB_MAKE64(0x0060000000)
+#define A_PHYS_MEMORY_1			_SB_MAKE64(0x0080000000)
+#define A_PHYS_MEMORY_2			_SB_MAKE64(0x0090000000)
+#define A_PHYS_MEMORY_3			_SB_MAKE64(0x00C0000000)
+#define A_PHYS_L2_CACHE_TEST		_SB_MAKE64(0x00D0000000)
+#define A_PHYS_LDT_SPECIAL_MATCH_BYTES	_SB_MAKE64(0x00D8000000)
+#define A_PHYS_LDTPCI_IO_MATCH_BYTES	_SB_MAKE64(0x00DC000000)
+#define A_PHYS_LDTPCI_CFG_MATCH_BYTES	_SB_MAKE64(0x00DE000000)
+#define A_PHYS_LDT_SPECIAL_MATCH_BITS	_SB_MAKE64(0x00F8000000)
+#define A_PHYS_LDTPCI_IO_MATCH_BITS	_SB_MAKE64(0x00FC000000)
+#define A_PHYS_LDTPCI_CFG_MATCH_BITS	_SB_MAKE64(0x00FE000000)
+#define A_PHYS_MEMORY_EXP		_SB_MAKE64(0x0100000000)
+#define A_PHYS_MEMORY_EXP_SIZE		_SB_MAKE64((508*1024*1024*1024))
+#define A_PHYS_LDT_EXP			_SB_MAKE64(0x8000000000)
+#define A_PHYS_PCI_FULLACCESS_BYTES	_SB_MAKE64(0xF000000000)
+#define A_PHYS_PCI_FULLACCESS_BITS	_SB_MAKE64(0xF100000000)
+#define A_PHYS_RESERVED			_SB_MAKE64(0xF200000000)
+#define A_PHYS_RESERVED_SPECIAL_LDT	_SB_MAKE64(0xFD00000000)
+
+#define A_PHYS_L2CACHE_WAY_SIZE		_SB_MAKE64(0x0000020000)
+#define PHYS_L2CACHE_NUM_WAYS		4
+#define A_PHYS_L2CACHE_TOTAL_SIZE	_SB_MAKE64(0x0000080000)
+#define A_PHYS_L2CACHE_WAY0		_SB_MAKE64(0x00D0180000)
+#define A_PHYS_L2CACHE_WAY1		_SB_MAKE64(0x00D01A0000)
+#define A_PHYS_L2CACHE_WAY2		_SB_MAKE64(0x00D01C0000)
+#define A_PHYS_L2CACHE_WAY3		_SB_MAKE64(0x00D01E0000)
+#endif
+
+
+#endif
diff --git a/arch/mips/include/asm/sibyte/sb1250_scd.h b/arch/mips/include/asm/sibyte/sb1250_scd.h
new file mode 100644
index 000000000..d099dcbef
--- /dev/null
+++ b/arch/mips/include/asm/sibyte/sb1250_scd.h
@@ -0,0 +1,641 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*  *********************************************************************
+    *  SB1250 Board Support Package
+    *
+    *  SCD Constants and Macros			File: sb1250_scd.h
+    *
+    *  This module contains constants and macros useful for
+    *  manipulating the System Control and Debug module on the 1250.
+    *
+    *  SB1250 specification level:  User's manual 1/02/02
+    *
+    *********************************************************************
+    *
+    *  Copyright 2000,2001,2002,2003,2004,2005
+    *  Broadcom Corporation. All rights reserved.
+    *
+    ********************************************************************* */
+
+#ifndef _SB1250_SCD_H
+#define _SB1250_SCD_H
+
+#include <asm/sibyte/sb1250_defs.h>
+
+/*  *********************************************************************
+    *  System control/debug registers
+    ********************************************************************* */
+
+/*
+ * System Revision Register (Table 4-1)
+ */
+
+#define M_SYS_RESERVED		    _SB_MAKEMASK(8, 0)
+
+#define S_SYS_REVISION		    _SB_MAKE64(8)
+#define M_SYS_REVISION		    _SB_MAKEMASK(8, S_SYS_REVISION)
+#define V_SYS_REVISION(x)	    _SB_MAKEVALUE(x, S_SYS_REVISION)
+#define G_SYS_REVISION(x)	    _SB_GETVALUE(x, S_SYS_REVISION, M_SYS_REVISION)
+
+#define K_SYS_REVISION_BCM1250_PASS1	0x01
+
+#define K_SYS_REVISION_BCM1250_PASS2	0x03
+#define K_SYS_REVISION_BCM1250_A1	0x03	/* Pass 2.0 WB */
+#define K_SYS_REVISION_BCM1250_A2	0x04	/* Pass 2.0 FC */
+#define K_SYS_REVISION_BCM1250_A3	0x05	/* Pass 2.1 FC */
+#define K_SYS_REVISION_BCM1250_A4	0x06	/* Pass 2.1 WB */
+#define K_SYS_REVISION_BCM1250_A6	0x07	/* OR 0x04 (A2) w/WID != 0 */
+#define K_SYS_REVISION_BCM1250_A8	0x0b	/* A8/A10 */
+#define K_SYS_REVISION_BCM1250_A9	0x08
+#define K_SYS_REVISION_BCM1250_A10	K_SYS_REVISION_BCM1250_A8
+
+#define K_SYS_REVISION_BCM1250_PASS2_2	0x10
+#define K_SYS_REVISION_BCM1250_B0	K_SYS_REVISION_BCM1250_B1
+#define K_SYS_REVISION_BCM1250_B1	0x10
+#define K_SYS_REVISION_BCM1250_B2	0x11
+
+#define K_SYS_REVISION_BCM1250_C0	0x20
+#define K_SYS_REVISION_BCM1250_C1	0x21
+#define K_SYS_REVISION_BCM1250_C2	0x22
+#define K_SYS_REVISION_BCM1250_C3	0x23
+
+#if SIBYTE_HDR_FEATURE_CHIP(1250)
+/* XXX: discourage people from using these constants.  */
+#define K_SYS_REVISION_PASS1	    K_SYS_REVISION_BCM1250_PASS1
+#define K_SYS_REVISION_PASS2	    K_SYS_REVISION_BCM1250_PASS2
+#define K_SYS_REVISION_PASS2_2	    K_SYS_REVISION_BCM1250_PASS2_2
+#define K_SYS_REVISION_PASS3	    K_SYS_REVISION_BCM1250_PASS3
+#define K_SYS_REVISION_BCM1250_PASS3	K_SYS_REVISION_BCM1250_C0
+#endif /* 1250 */
+
+#define K_SYS_REVISION_BCM112x_A1	0x20
+#define K_SYS_REVISION_BCM112x_A2	0x21
+#define K_SYS_REVISION_BCM112x_A3	0x22
+#define K_SYS_REVISION_BCM112x_A4	0x23
+#define K_SYS_REVISION_BCM112x_B0	0x30
+
+#define K_SYS_REVISION_BCM1480_S0	0x01
+#define K_SYS_REVISION_BCM1480_A1	0x02
+#define K_SYS_REVISION_BCM1480_A2	0x03
+#define K_SYS_REVISION_BCM1480_A3	0x04
+#define K_SYS_REVISION_BCM1480_B0	0x11
+
+/*Cache size - 23:20  of revision register*/
+#define S_SYS_L2C_SIZE		  _SB_MAKE64(20)
+#define M_SYS_L2C_SIZE		  _SB_MAKEMASK(4, S_SYS_L2C_SIZE)
+#define V_SYS_L2C_SIZE(x)	  _SB_MAKEVALUE(x, S_SYS_L2C_SIZE)
+#define G_SYS_L2C_SIZE(x)	  _SB_GETVALUE(x, S_SYS_L2C_SIZE, M_SYS_L2C_SIZE)
+
+#define K_SYS_L2C_SIZE_1MB	0
+#define K_SYS_L2C_SIZE_512KB	5
+#define K_SYS_L2C_SIZE_256KB	2
+#define K_SYS_L2C_SIZE_128KB	1
+
+#define K_SYS_L2C_SIZE_BCM1250	K_SYS_L2C_SIZE_512KB
+#define K_SYS_L2C_SIZE_BCM1125	K_SYS_L2C_SIZE_256KB
+#define K_SYS_L2C_SIZE_BCM1122	K_SYS_L2C_SIZE_128KB
+
+
+/* Number of CPU cores, bits 27:24  of revision register*/
+#define S_SYS_NUM_CPUS		  _SB_MAKE64(24)
+#define M_SYS_NUM_CPUS		  _SB_MAKEMASK(4, S_SYS_NUM_CPUS)
+#define V_SYS_NUM_CPUS(x)	  _SB_MAKEVALUE(x, S_SYS_NUM_CPUS)
+#define G_SYS_NUM_CPUS(x)	  _SB_GETVALUE(x, S_SYS_NUM_CPUS, M_SYS_NUM_CPUS)
+
+
+/* XXX: discourage people from using these constants.  */
+#define S_SYS_PART		    _SB_MAKE64(16)
+#define M_SYS_PART		    _SB_MAKEMASK(16, S_SYS_PART)
+#define V_SYS_PART(x)		    _SB_MAKEVALUE(x, S_SYS_PART)
+#define G_SYS_PART(x)		    _SB_GETVALUE(x, S_SYS_PART, M_SYS_PART)
+
+/* XXX: discourage people from using these constants.  */
+#define K_SYS_PART_SB1250	    0x1250
+#define K_SYS_PART_BCM1120	    0x1121
+#define K_SYS_PART_BCM1125	    0x1123
+#define K_SYS_PART_BCM1125H	    0x1124
+#define K_SYS_PART_BCM1122	    0x1113
+
+
+/* The "peripheral set" (SOC type) is the low 4 bits of the "part" field.  */
+#define S_SYS_SOC_TYPE		    _SB_MAKE64(16)
+#define M_SYS_SOC_TYPE		    _SB_MAKEMASK(4, S_SYS_SOC_TYPE)
+#define V_SYS_SOC_TYPE(x)	    _SB_MAKEVALUE(x, S_SYS_SOC_TYPE)
+#define G_SYS_SOC_TYPE(x)	    _SB_GETVALUE(x, S_SYS_SOC_TYPE, M_SYS_SOC_TYPE)
+
+#define K_SYS_SOC_TYPE_BCM1250	    0x0
+#define K_SYS_SOC_TYPE_BCM1120	    0x1
+#define K_SYS_SOC_TYPE_BCM1250_ALT  0x2		/* 1250pass2 w/ 1/4 L2.	 */
+#define K_SYS_SOC_TYPE_BCM1125	    0x3
+#define K_SYS_SOC_TYPE_BCM1125H	    0x4
+#define K_SYS_SOC_TYPE_BCM1250_ALT2 0x5		/* 1250pass2 w/ 1/2 L2.	 */
+#define K_SYS_SOC_TYPE_BCM1x80	    0x6
+#define K_SYS_SOC_TYPE_BCM1x55	    0x7
+
+/*
+ * Calculate correct SOC type given a copy of system revision register.
+ *
+ * (For the assembler version, sysrev and dest may be the same register.
+ * Also, it clobbers AT.)
+ */
+#ifdef __ASSEMBLER__
+#define SYS_SOC_TYPE(dest, sysrev)					\
+	.set push ;							\
+	.set reorder ;							\
+	dsrl	dest, sysrev, S_SYS_SOC_TYPE ;				\
+	andi	dest, dest, (M_SYS_SOC_TYPE >> S_SYS_SOC_TYPE);		\
+	beq	dest, K_SYS_SOC_TYPE_BCM1250_ALT, 991f ;		\
+	beq	dest, K_SYS_SOC_TYPE_BCM1250_ALT2, 991f	 ;		\
+	b	992f ;							\
+991:	li	dest, K_SYS_SOC_TYPE_BCM1250 ;				\
+992:									\
+	.set pop
+#else
+#define SYS_SOC_TYPE(sysrev)						\
+	((G_SYS_SOC_TYPE(sysrev) == K_SYS_SOC_TYPE_BCM1250_ALT		\
+	  || G_SYS_SOC_TYPE(sysrev) == K_SYS_SOC_TYPE_BCM1250_ALT2)	\
+	 ? K_SYS_SOC_TYPE_BCM1250 : G_SYS_SOC_TYPE(sysrev))
+#endif
+
+#define S_SYS_WID		    _SB_MAKE64(32)
+#define M_SYS_WID		    _SB_MAKEMASK(32, S_SYS_WID)
+#define V_SYS_WID(x)		    _SB_MAKEVALUE(x, S_SYS_WID)
+#define G_SYS_WID(x)		    _SB_GETVALUE(x, S_SYS_WID, M_SYS_WID)
+
+/*
+ * System Manufacturing Register
+ * Register: SCD_SYSTEM_MANUF
+ */
+
+#if SIBYTE_HDR_FEATURE_1250_112x
+/* Wafer ID: bits 31:0 */
+#define S_SYS_WAFERID1_200	  _SB_MAKE64(0)
+#define M_SYS_WAFERID1_200	  _SB_MAKEMASK(32, S_SYS_WAFERID1_200)
+#define V_SYS_WAFERID1_200(x)	  _SB_MAKEVALUE(x, S_SYS_WAFERID1_200)
+#define G_SYS_WAFERID1_200(x)	  _SB_GETVALUE(x, S_SYS_WAFERID1_200, M_SYS_WAFERID1_200)
+
+#define S_SYS_BIN		  _SB_MAKE64(32)
+#define M_SYS_BIN		  _SB_MAKEMASK(4, S_SYS_BIN)
+#define V_SYS_BIN(x)		  _SB_MAKEVALUE(x, S_SYS_BIN)
+#define G_SYS_BIN(x)		  _SB_GETVALUE(x, S_SYS_BIN, M_SYS_BIN)
+
+/* Wafer ID: bits 39:36 */
+#define S_SYS_WAFERID2_200	  _SB_MAKE64(36)
+#define M_SYS_WAFERID2_200	  _SB_MAKEMASK(4, S_SYS_WAFERID2_200)
+#define V_SYS_WAFERID2_200(x)	  _SB_MAKEVALUE(x, S_SYS_WAFERID2_200)
+#define G_SYS_WAFERID2_200(x)	  _SB_GETVALUE(x, S_SYS_WAFERID2_200, M_SYS_WAFERID2_200)
+
+/* Wafer ID: bits 39:0 */
+#define S_SYS_WAFERID_300	  _SB_MAKE64(0)
+#define M_SYS_WAFERID_300	  _SB_MAKEMASK(40, S_SYS_WAFERID_300)
+#define V_SYS_WAFERID_300(x)	  _SB_MAKEVALUE(x, S_SYS_WAFERID_300)
+#define G_SYS_WAFERID_300(x)	  _SB_GETVALUE(x, S_SYS_WAFERID_300, M_SYS_WAFERID_300)
+
+#define S_SYS_XPOS		  _SB_MAKE64(40)
+#define M_SYS_XPOS		  _SB_MAKEMASK(6, S_SYS_XPOS)
+#define V_SYS_XPOS(x)		  _SB_MAKEVALUE(x, S_SYS_XPOS)
+#define G_SYS_XPOS(x)		  _SB_GETVALUE(x, S_SYS_XPOS, M_SYS_XPOS)
+
+#define S_SYS_YPOS		  _SB_MAKE64(46)
+#define M_SYS_YPOS		  _SB_MAKEMASK(6, S_SYS_YPOS)
+#define V_SYS_YPOS(x)		  _SB_MAKEVALUE(x, S_SYS_YPOS)
+#define G_SYS_YPOS(x)		  _SB_GETVALUE(x, S_SYS_YPOS, M_SYS_YPOS)
+#endif
+
+
+/*
+ * System Config Register (Table 4-2)
+ * Register: SCD_SYSTEM_CFG
+ */
+
+#if SIBYTE_HDR_FEATURE_1250_112x
+#define M_SYS_LDT_PLL_BYP	    _SB_MAKEMASK1(3)
+#define M_SYS_PCI_SYNC_TEST_MODE    _SB_MAKEMASK1(4)
+#define M_SYS_IOB0_DIV		    _SB_MAKEMASK1(5)
+#define M_SYS_IOB1_DIV		    _SB_MAKEMASK1(6)
+
+#define S_SYS_PLL_DIV		    _SB_MAKE64(7)
+#define M_SYS_PLL_DIV		    _SB_MAKEMASK(5, S_SYS_PLL_DIV)
+#define V_SYS_PLL_DIV(x)	    _SB_MAKEVALUE(x, S_SYS_PLL_DIV)
+#define G_SYS_PLL_DIV(x)	    _SB_GETVALUE(x, S_SYS_PLL_DIV, M_SYS_PLL_DIV)
+
+#define M_SYS_SER0_ENABLE	    _SB_MAKEMASK1(12)
+#define M_SYS_SER0_RSTB_EN	    _SB_MAKEMASK1(13)
+#define M_SYS_SER1_ENABLE	    _SB_MAKEMASK1(14)
+#define M_SYS_SER1_RSTB_EN	    _SB_MAKEMASK1(15)
+#define M_SYS_PCMCIA_ENABLE	    _SB_MAKEMASK1(16)
+
+#define S_SYS_BOOT_MODE		    _SB_MAKE64(17)
+#define M_SYS_BOOT_MODE		    _SB_MAKEMASK(2, S_SYS_BOOT_MODE)
+#define V_SYS_BOOT_MODE(x)	    _SB_MAKEVALUE(x, S_SYS_BOOT_MODE)
+#define G_SYS_BOOT_MODE(x)	    _SB_GETVALUE(x, S_SYS_BOOT_MODE, M_SYS_BOOT_MODE)
+#define K_SYS_BOOT_MODE_ROM32	    0
+#define K_SYS_BOOT_MODE_ROM8	    1
+#define K_SYS_BOOT_MODE_SMBUS_SMALL 2
+#define K_SYS_BOOT_MODE_SMBUS_BIG   3
+
+#define M_SYS_PCI_HOST		    _SB_MAKEMASK1(19)
+#define M_SYS_PCI_ARBITER	    _SB_MAKEMASK1(20)
+#define M_SYS_SOUTH_ON_LDT	    _SB_MAKEMASK1(21)
+#define M_SYS_BIG_ENDIAN	    _SB_MAKEMASK1(22)
+#define M_SYS_GENCLK_EN		    _SB_MAKEMASK1(23)
+#define M_SYS_LDT_TEST_EN	    _SB_MAKEMASK1(24)
+#define M_SYS_GEN_PARITY_EN	    _SB_MAKEMASK1(25)
+
+#define S_SYS_CONFIG		    26
+#define M_SYS_CONFIG		    _SB_MAKEMASK(6, S_SYS_CONFIG)
+#define V_SYS_CONFIG(x)		    _SB_MAKEVALUE(x, S_SYS_CONFIG)
+#define G_SYS_CONFIG(x)		    _SB_GETVALUE(x, S_SYS_CONFIG, M_SYS_CONFIG)
+
+/* The following bits are writeable by JTAG only. */
+
+#define M_SYS_CLKSTOP		    _SB_MAKEMASK1(32)
+#define M_SYS_CLKSTEP		    _SB_MAKEMASK1(33)
+
+#define S_SYS_CLKCOUNT		    34
+#define M_SYS_CLKCOUNT		    _SB_MAKEMASK(8, S_SYS_CLKCOUNT)
+#define V_SYS_CLKCOUNT(x)	    _SB_MAKEVALUE(x, S_SYS_CLKCOUNT)
+#define G_SYS_CLKCOUNT(x)	    _SB_GETVALUE(x, S_SYS_CLKCOUNT, M_SYS_CLKCOUNT)
+
+#define M_SYS_PLL_BYPASS	    _SB_MAKEMASK1(42)
+
+#define S_SYS_PLL_IREF		    43
+#define M_SYS_PLL_IREF		    _SB_MAKEMASK(2, S_SYS_PLL_IREF)
+
+#define S_SYS_PLL_VCO		    45
+#define M_SYS_PLL_VCO		    _SB_MAKEMASK(2, S_SYS_PLL_VCO)
+
+#define S_SYS_PLL_VREG		    47
+#define M_SYS_PLL_VREG		    _SB_MAKEMASK(2, S_SYS_PLL_VREG)
+
+#define M_SYS_MEM_RESET		    _SB_MAKEMASK1(49)
+#define M_SYS_L2C_RESET		    _SB_MAKEMASK1(50)
+#define M_SYS_IO_RESET_0	    _SB_MAKEMASK1(51)
+#define M_SYS_IO_RESET_1	    _SB_MAKEMASK1(52)
+#define M_SYS_SCD_RESET		    _SB_MAKEMASK1(53)
+
+/* End of bits writable by JTAG only. */
+
+#define M_SYS_CPU_RESET_0	    _SB_MAKEMASK1(54)
+#define M_SYS_CPU_RESET_1	    _SB_MAKEMASK1(55)
+
+#define M_SYS_UNICPU0		    _SB_MAKEMASK1(56)
+#define M_SYS_UNICPU1		    _SB_MAKEMASK1(57)
+
+#define M_SYS_SB_SOFTRES	    _SB_MAKEMASK1(58)
+#define M_SYS_EXT_RESET		    _SB_MAKEMASK1(59)
+#define M_SYS_SYSTEM_RESET	    _SB_MAKEMASK1(60)
+
+#define M_SYS_MISR_MODE		    _SB_MAKEMASK1(61)
+#define M_SYS_MISR_RESET	    _SB_MAKEMASK1(62)
+
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1)
+#define M_SYS_SW_FLAG		    _SB_MAKEMASK1(63)
+#endif /* 1250 PASS2 || 112x PASS1 */
+
+#endif
+
+
+/*
+ * Mailbox Registers (Table 4-3)
+ * Registers: SCD_MBOX_CPU_x
+ */
+
+#define S_MBOX_INT_3		    0
+#define M_MBOX_INT_3		    _SB_MAKEMASK(16, S_MBOX_INT_3)
+#define S_MBOX_INT_2		    16
+#define M_MBOX_INT_2		    _SB_MAKEMASK(16, S_MBOX_INT_2)
+#define S_MBOX_INT_1		    32
+#define M_MBOX_INT_1		    _SB_MAKEMASK(16, S_MBOX_INT_1)
+#define S_MBOX_INT_0		    48
+#define M_MBOX_INT_0		    _SB_MAKEMASK(16, S_MBOX_INT_0)
+
+/*
+ * Watchdog Registers (Table 4-8) (Table 4-9) (Table 4-10)
+ * Registers: SCD_WDOG_INIT_CNT_x
+ */
+
+#define V_SCD_WDOG_FREQ		    1000000
+
+#define S_SCD_WDOG_INIT		    0
+#define M_SCD_WDOG_INIT		    _SB_MAKEMASK(23, S_SCD_WDOG_INIT)
+
+#define S_SCD_WDOG_CNT		    0
+#define M_SCD_WDOG_CNT		    _SB_MAKEMASK(23, S_SCD_WDOG_CNT)
+
+#define S_SCD_WDOG_ENABLE	    0
+#define M_SCD_WDOG_ENABLE	    _SB_MAKEMASK1(S_SCD_WDOG_ENABLE)
+
+#define S_SCD_WDOG_RESET_TYPE	    2
+#define M_SCD_WDOG_RESET_TYPE	    _SB_MAKEMASK(3, S_SCD_WDOG_RESET_TYPE)
+#define V_SCD_WDOG_RESET_TYPE(x)    _SB_MAKEVALUE(x, S_SCD_WDOG_RESET_TYPE)
+#define G_SCD_WDOG_RESET_TYPE(x)    _SB_GETVALUE(x, S_SCD_WDOG_RESET_TYPE, M_SCD_WDOG_RESET_TYPE)
+
+#define K_SCD_WDOG_RESET_FULL	    0	/* actually, (x & 1) == 0  */
+#define K_SCD_WDOG_RESET_SOFT	    1
+#define K_SCD_WDOG_RESET_CPU0	    3
+#define K_SCD_WDOG_RESET_CPU1	    5
+#define K_SCD_WDOG_RESET_BOTH_CPUS  7
+
+/* This feature is present in 1250 C0 and later, but *not* in 112x A revs.  */
+#if SIBYTE_HDR_FEATURE(1250, PASS3)
+#define S_SCD_WDOG_HAS_RESET	    8
+#define M_SCD_WDOG_HAS_RESET	    _SB_MAKEMASK1(S_SCD_WDOG_HAS_RESET)
+#endif
+
+
+/*
+ * Timer Registers (Table 4-11) (Table 4-12) (Table 4-13)
+ */
+
+#define V_SCD_TIMER_FREQ	    1000000
+
+#define S_SCD_TIMER_INIT	    0
+#define M_SCD_TIMER_INIT	    _SB_MAKEMASK(23, S_SCD_TIMER_INIT)
+#define V_SCD_TIMER_INIT(x)	    _SB_MAKEVALUE(x, S_SCD_TIMER_INIT)
+#define G_SCD_TIMER_INIT(x)	    _SB_GETVALUE(x, S_SCD_TIMER_INIT, M_SCD_TIMER_INIT)
+
+#define V_SCD_TIMER_WIDTH	    23
+#define S_SCD_TIMER_CNT		    0
+#define M_SCD_TIMER_CNT		    _SB_MAKEMASK(V_SCD_TIMER_WIDTH, S_SCD_TIMER_CNT)
+#define V_SCD_TIMER_CNT(x)	   _SB_MAKEVALUE(x, S_SCD_TIMER_CNT)
+#define G_SCD_TIMER_CNT(x)	   _SB_GETVALUE(x, S_SCD_TIMER_CNT, M_SCD_TIMER_CNT)
+
+#define M_SCD_TIMER_ENABLE	    _SB_MAKEMASK1(0)
+#define M_SCD_TIMER_MODE	    _SB_MAKEMASK1(1)
+#define M_SCD_TIMER_MODE_CONTINUOUS M_SCD_TIMER_MODE
+
+/*
+ * System Performance Counters
+ */
+
+#define S_SPC_CFG_SRC0		  0
+#define M_SPC_CFG_SRC0		  _SB_MAKEMASK(8, S_SPC_CFG_SRC0)
+#define V_SPC_CFG_SRC0(x)	  _SB_MAKEVALUE(x, S_SPC_CFG_SRC0)
+#define G_SPC_CFG_SRC0(x)	  _SB_GETVALUE(x, S_SPC_CFG_SRC0, M_SPC_CFG_SRC0)
+
+#define S_SPC_CFG_SRC1		  8
+#define M_SPC_CFG_SRC1		  _SB_MAKEMASK(8, S_SPC_CFG_SRC1)
+#define V_SPC_CFG_SRC1(x)	  _SB_MAKEVALUE(x, S_SPC_CFG_SRC1)
+#define G_SPC_CFG_SRC1(x)	  _SB_GETVALUE(x, S_SPC_CFG_SRC1, M_SPC_CFG_SRC1)
+
+#define S_SPC_CFG_SRC2		  16
+#define M_SPC_CFG_SRC2		  _SB_MAKEMASK(8, S_SPC_CFG_SRC2)
+#define V_SPC_CFG_SRC2(x)	  _SB_MAKEVALUE(x, S_SPC_CFG_SRC2)
+#define G_SPC_CFG_SRC2(x)	  _SB_GETVALUE(x, S_SPC_CFG_SRC2, M_SPC_CFG_SRC2)
+
+#define S_SPC_CFG_SRC3		  24
+#define M_SPC_CFG_SRC3		  _SB_MAKEMASK(8, S_SPC_CFG_SRC3)
+#define V_SPC_CFG_SRC3(x)	  _SB_MAKEVALUE(x, S_SPC_CFG_SRC3)
+#define G_SPC_CFG_SRC3(x)	  _SB_GETVALUE(x, S_SPC_CFG_SRC3, M_SPC_CFG_SRC3)
+
+#if SIBYTE_HDR_FEATURE_1250_112x
+#define M_SPC_CFG_CLEAR		_SB_MAKEMASK1(32)
+#define M_SPC_CFG_ENABLE	_SB_MAKEMASK1(33)
+#endif
+
+
+/*
+ * Bus Watcher
+ */
+
+#define S_SCD_BERR_TID		  8
+#define M_SCD_BERR_TID		  _SB_MAKEMASK(10, S_SCD_BERR_TID)
+#define V_SCD_BERR_TID(x)	  _SB_MAKEVALUE(x, S_SCD_BERR_TID)
+#define G_SCD_BERR_TID(x)	  _SB_GETVALUE(x, S_SCD_BERR_TID, M_SCD_BERR_TID)
+
+#define S_SCD_BERR_RID		  18
+#define M_SCD_BERR_RID		  _SB_MAKEMASK(4, S_SCD_BERR_RID)
+#define V_SCD_BERR_RID(x)	  _SB_MAKEVALUE(x, S_SCD_BERR_RID)
+#define G_SCD_BERR_RID(x)	  _SB_GETVALUE(x, S_SCD_BERR_RID, M_SCD_BERR_RID)
+
+#define S_SCD_BERR_DCODE	  22
+#define M_SCD_BERR_DCODE	  _SB_MAKEMASK(3, S_SCD_BERR_DCODE)
+#define V_SCD_BERR_DCODE(x)	  _SB_MAKEVALUE(x, S_SCD_BERR_DCODE)
+#define G_SCD_BERR_DCODE(x)	  _SB_GETVALUE(x, S_SCD_BERR_DCODE, M_SCD_BERR_DCODE)
+
+#define M_SCD_BERR_MULTERRS	  _SB_MAKEMASK1(30)
+
+
+#define S_SCD_L2ECC_CORR_D	  0
+#define M_SCD_L2ECC_CORR_D	  _SB_MAKEMASK(8, S_SCD_L2ECC_CORR_D)
+#define V_SCD_L2ECC_CORR_D(x)	  _SB_MAKEVALUE(x, S_SCD_L2ECC_CORR_D)
+#define G_SCD_L2ECC_CORR_D(x)	  _SB_GETVALUE(x, S_SCD_L2ECC_CORR_D, M_SCD_L2ECC_CORR_D)
+
+#define S_SCD_L2ECC_BAD_D	  8
+#define M_SCD_L2ECC_BAD_D	  _SB_MAKEMASK(8, S_SCD_L2ECC_BAD_D)
+#define V_SCD_L2ECC_BAD_D(x)	  _SB_MAKEVALUE(x, S_SCD_L2ECC_BAD_D)
+#define G_SCD_L2ECC_BAD_D(x)	  _SB_GETVALUE(x, S_SCD_L2ECC_BAD_D, M_SCD_L2ECC_BAD_D)
+
+#define S_SCD_L2ECC_CORR_T	  16
+#define M_SCD_L2ECC_CORR_T	  _SB_MAKEMASK(8, S_SCD_L2ECC_CORR_T)
+#define V_SCD_L2ECC_CORR_T(x)	  _SB_MAKEVALUE(x, S_SCD_L2ECC_CORR_T)
+#define G_SCD_L2ECC_CORR_T(x)	  _SB_GETVALUE(x, S_SCD_L2ECC_CORR_T, M_SCD_L2ECC_CORR_T)
+
+#define S_SCD_L2ECC_BAD_T	  24
+#define M_SCD_L2ECC_BAD_T	  _SB_MAKEMASK(8, S_SCD_L2ECC_BAD_T)
+#define V_SCD_L2ECC_BAD_T(x)	  _SB_MAKEVALUE(x, S_SCD_L2ECC_BAD_T)
+#define G_SCD_L2ECC_BAD_T(x)	  _SB_GETVALUE(x, S_SCD_L2ECC_BAD_T, M_SCD_L2ECC_BAD_T)
+
+#define S_SCD_MEM_ECC_CORR	  0
+#define M_SCD_MEM_ECC_CORR	  _SB_MAKEMASK(8, S_SCD_MEM_ECC_CORR)
+#define V_SCD_MEM_ECC_CORR(x)	  _SB_MAKEVALUE(x, S_SCD_MEM_ECC_CORR)
+#define G_SCD_MEM_ECC_CORR(x)	  _SB_GETVALUE(x, S_SCD_MEM_ECC_CORR, M_SCD_MEM_ECC_CORR)
+
+#define S_SCD_MEM_ECC_BAD	  8
+#define M_SCD_MEM_ECC_BAD	  _SB_MAKEMASK(8, S_SCD_MEM_ECC_BAD)
+#define V_SCD_MEM_ECC_BAD(x)	  _SB_MAKEVALUE(x, S_SCD_MEM_ECC_BAD)
+#define G_SCD_MEM_ECC_BAD(x)	  _SB_GETVALUE(x, S_SCD_MEM_ECC_BAD, M_SCD_MEM_ECC_BAD)
+
+#define S_SCD_MEM_BUSERR	  16
+#define M_SCD_MEM_BUSERR	  _SB_MAKEMASK(8, S_SCD_MEM_BUSERR)
+#define V_SCD_MEM_BUSERR(x)	  _SB_MAKEVALUE(x, S_SCD_MEM_BUSERR)
+#define G_SCD_MEM_BUSERR(x)	  _SB_GETVALUE(x, S_SCD_MEM_BUSERR, M_SCD_MEM_BUSERR)
+
+
+/*
+ * Address Trap Registers
+ */
+
+#if SIBYTE_HDR_FEATURE_1250_112x
+#define M_ATRAP_INDEX		  _SB_MAKEMASK(4, 0)
+#define M_ATRAP_ADDRESS		  _SB_MAKEMASK(40, 0)
+
+#define S_ATRAP_CFG_CNT		   0
+#define M_ATRAP_CFG_CNT		   _SB_MAKEMASK(3, S_ATRAP_CFG_CNT)
+#define V_ATRAP_CFG_CNT(x)	   _SB_MAKEVALUE(x, S_ATRAP_CFG_CNT)
+#define G_ATRAP_CFG_CNT(x)	   _SB_GETVALUE(x, S_ATRAP_CFG_CNT, M_ATRAP_CFG_CNT)
+
+#define M_ATRAP_CFG_WRITE	   _SB_MAKEMASK1(3)
+#define M_ATRAP_CFG_ALL		   _SB_MAKEMASK1(4)
+#define M_ATRAP_CFG_INV		   _SB_MAKEMASK1(5)
+#define M_ATRAP_CFG_USESRC	   _SB_MAKEMASK1(6)
+#define M_ATRAP_CFG_SRCINV	   _SB_MAKEMASK1(7)
+
+#define S_ATRAP_CFG_AGENTID	8
+#define M_ATRAP_CFG_AGENTID	_SB_MAKEMASK(4, S_ATRAP_CFG_AGENTID)
+#define V_ATRAP_CFG_AGENTID(x)	_SB_MAKEVALUE(x, S_ATRAP_CFG_AGENTID)
+#define G_ATRAP_CFG_AGENTID(x)	_SB_GETVALUE(x, S_ATRAP_CFG_AGENTID, M_ATRAP_CFG_AGENTID)
+
+#define K_BUS_AGENT_CPU0	0
+#define K_BUS_AGENT_CPU1	1
+#define K_BUS_AGENT_IOB0	2
+#define K_BUS_AGENT_IOB1	3
+#define K_BUS_AGENT_SCD 4
+#define K_BUS_AGENT_L2C 6
+#define K_BUS_AGENT_MC	7
+
+#define S_ATRAP_CFG_CATTR     12
+#define M_ATRAP_CFG_CATTR     _SB_MAKEMASK(3, S_ATRAP_CFG_CATTR)
+#define V_ATRAP_CFG_CATTR(x)  _SB_MAKEVALUE(x, S_ATRAP_CFG_CATTR)
+#define G_ATRAP_CFG_CATTR(x)  _SB_GETVALUE(x, S_ATRAP_CFG_CATTR, M_ATRAP_CFG_CATTR)
+
+#define K_ATRAP_CFG_CATTR_IGNORE	0
+#define K_ATRAP_CFG_CATTR_UNC		1
+#define K_ATRAP_CFG_CATTR_CACHEABLE	2
+#define K_ATRAP_CFG_CATTR_NONCOH	3
+#define K_ATRAP_CFG_CATTR_COHERENT	4
+#define K_ATRAP_CFG_CATTR_NOTUNC	5
+#define K_ATRAP_CFG_CATTR_NOTNONCOH	6
+#define K_ATRAP_CFG_CATTR_NOTCOHERENT	7
+
+#endif	/* 1250/112x */
+
+/*
+ * Trace Buffer Config register
+ */
+
+#define M_SCD_TRACE_CFG_RESET		_SB_MAKEMASK1(0)
+#define M_SCD_TRACE_CFG_START_READ	_SB_MAKEMASK1(1)
+#define M_SCD_TRACE_CFG_START		_SB_MAKEMASK1(2)
+#define M_SCD_TRACE_CFG_STOP		_SB_MAKEMASK1(3)
+#define M_SCD_TRACE_CFG_FREEZE		_SB_MAKEMASK1(4)
+#define M_SCD_TRACE_CFG_FREEZE_FULL	_SB_MAKEMASK1(5)
+#define M_SCD_TRACE_CFG_DEBUG_FULL	_SB_MAKEMASK1(6)
+#define M_SCD_TRACE_CFG_FULL		_SB_MAKEMASK1(7)
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define M_SCD_TRACE_CFG_FORCECNT	_SB_MAKEMASK1(8)
+#endif /* 1250 PASS2 || 112x PASS1 || 1480 */
+
+/*
+ * This field is the same on the 1250/112x and 1480, just located in
+ * a slightly different place in the register.
+ */
+#if SIBYTE_HDR_FEATURE_1250_112x
+#define S_SCD_TRACE_CFG_CUR_ADDR	10
+#else
+#if SIBYTE_HDR_FEATURE_CHIP(1480)
+#define S_SCD_TRACE_CFG_CUR_ADDR	24
+#endif	/* 1480 */
+#endif	/* 1250/112x */
+
+#define M_SCD_TRACE_CFG_CUR_ADDR	_SB_MAKEMASK(8, S_SCD_TRACE_CFG_CUR_ADDR)
+#define V_SCD_TRACE_CFG_CUR_ADDR(x)	_SB_MAKEVALUE(x, S_SCD_TRACE_CFG_CUR_ADDR)
+#define G_SCD_TRACE_CFG_CUR_ADDR(x)	_SB_GETVALUE(x, S_SCD_TRACE_CFG_CUR_ADDR, M_SCD_TRACE_CFG_CUR_ADDR)
+
+/*
+ * Trace Event registers
+ */
+
+#define S_SCD_TREVT_ADDR_MATCH		0
+#define M_SCD_TREVT_ADDR_MATCH		_SB_MAKEMASK(4, S_SCD_TREVT_ADDR_MATCH)
+#define V_SCD_TREVT_ADDR_MATCH(x)	_SB_MAKEVALUE(x, S_SCD_TREVT_ADDR_MATCH)
+#define G_SCD_TREVT_ADDR_MATCH(x)	_SB_GETVALUE(x, S_SCD_TREVT_ADDR_MATCH, M_SCD_TREVT_ADDR_MATCH)
+
+#define M_SCD_TREVT_REQID_MATCH		_SB_MAKEMASK1(4)
+#define M_SCD_TREVT_DATAID_MATCH	_SB_MAKEMASK1(5)
+#define M_SCD_TREVT_RESPID_MATCH	_SB_MAKEMASK1(6)
+#define M_SCD_TREVT_INTERRUPT		_SB_MAKEMASK1(7)
+#define M_SCD_TREVT_DEBUG_PIN		_SB_MAKEMASK1(9)
+#define M_SCD_TREVT_WRITE		_SB_MAKEMASK1(10)
+#define M_SCD_TREVT_READ		_SB_MAKEMASK1(11)
+
+#define S_SCD_TREVT_REQID		12
+#define M_SCD_TREVT_REQID		_SB_MAKEMASK(4, S_SCD_TREVT_REQID)
+#define V_SCD_TREVT_REQID(x)		_SB_MAKEVALUE(x, S_SCD_TREVT_REQID)
+#define G_SCD_TREVT_REQID(x)		_SB_GETVALUE(x, S_SCD_TREVT_REQID, M_SCD_TREVT_REQID)
+
+#define S_SCD_TREVT_RESPID		16
+#define M_SCD_TREVT_RESPID		_SB_MAKEMASK(4, S_SCD_TREVT_RESPID)
+#define V_SCD_TREVT_RESPID(x)		_SB_MAKEVALUE(x, S_SCD_TREVT_RESPID)
+#define G_SCD_TREVT_RESPID(x)		_SB_GETVALUE(x, S_SCD_TREVT_RESPID, M_SCD_TREVT_RESPID)
+
+#define S_SCD_TREVT_DATAID		20
+#define M_SCD_TREVT_DATAID		_SB_MAKEMASK(4, S_SCD_TREVT_DATAID)
+#define V_SCD_TREVT_DATAID(x)		_SB_MAKEVALUE(x, S_SCD_TREVT_DATAID)
+#define G_SCD_TREVT_DATAID(x)		_SB_GETVALUE(x, S_SCD_TREVT_DATAID, M_SCD_TREVT_DATID)
+
+#define S_SCD_TREVT_COUNT		24
+#define M_SCD_TREVT_COUNT		_SB_MAKEMASK(8, S_SCD_TREVT_COUNT)
+#define V_SCD_TREVT_COUNT(x)		_SB_MAKEVALUE(x, S_SCD_TREVT_COUNT)
+#define G_SCD_TREVT_COUNT(x)		_SB_GETVALUE(x, S_SCD_TREVT_COUNT, M_SCD_TREVT_COUNT)
+
+/*
+ * Trace Sequence registers
+ */
+
+#define S_SCD_TRSEQ_EVENT4		0
+#define M_SCD_TRSEQ_EVENT4		_SB_MAKEMASK(4, S_SCD_TRSEQ_EVENT4)
+#define V_SCD_TRSEQ_EVENT4(x)		_SB_MAKEVALUE(x, S_SCD_TRSEQ_EVENT4)
+#define G_SCD_TRSEQ_EVENT4(x)		_SB_GETVALUE(x, S_SCD_TRSEQ_EVENT4, M_SCD_TRSEQ_EVENT4)
+
+#define S_SCD_TRSEQ_EVENT3		4
+#define M_SCD_TRSEQ_EVENT3		_SB_MAKEMASK(4, S_SCD_TRSEQ_EVENT3)
+#define V_SCD_TRSEQ_EVENT3(x)		_SB_MAKEVALUE(x, S_SCD_TRSEQ_EVENT3)
+#define G_SCD_TRSEQ_EVENT3(x)		_SB_GETVALUE(x, S_SCD_TRSEQ_EVENT3, M_SCD_TRSEQ_EVENT3)
+
+#define S_SCD_TRSEQ_EVENT2		8
+#define M_SCD_TRSEQ_EVENT2		_SB_MAKEMASK(4, S_SCD_TRSEQ_EVENT2)
+#define V_SCD_TRSEQ_EVENT2(x)		_SB_MAKEVALUE(x, S_SCD_TRSEQ_EVENT2)
+#define G_SCD_TRSEQ_EVENT2(x)		_SB_GETVALUE(x, S_SCD_TRSEQ_EVENT2, M_SCD_TRSEQ_EVENT2)
+
+#define S_SCD_TRSEQ_EVENT1		12
+#define M_SCD_TRSEQ_EVENT1		_SB_MAKEMASK(4, S_SCD_TRSEQ_EVENT1)
+#define V_SCD_TRSEQ_EVENT1(x)		_SB_MAKEVALUE(x, S_SCD_TRSEQ_EVENT1)
+#define G_SCD_TRSEQ_EVENT1(x)		_SB_GETVALUE(x, S_SCD_TRSEQ_EVENT1, M_SCD_TRSEQ_EVENT1)
+
+#define K_SCD_TRSEQ_E0			0
+#define K_SCD_TRSEQ_E1			1
+#define K_SCD_TRSEQ_E2			2
+#define K_SCD_TRSEQ_E3			3
+#define K_SCD_TRSEQ_E0_E1		4
+#define K_SCD_TRSEQ_E1_E2		5
+#define K_SCD_TRSEQ_E2_E3		6
+#define K_SCD_TRSEQ_E0_E1_E2		7
+#define K_SCD_TRSEQ_E0_E1_E2_E3		8
+#define K_SCD_TRSEQ_E0E1		9
+#define K_SCD_TRSEQ_E0E1E2		10
+#define K_SCD_TRSEQ_E0E1E2E3		11
+#define K_SCD_TRSEQ_E0E1_E2		12
+#define K_SCD_TRSEQ_E0E1_E2E3		13
+#define K_SCD_TRSEQ_E0E1_E2_E3		14
+#define K_SCD_TRSEQ_IGNORED		15
+
+#define K_SCD_TRSEQ_TRIGGER_ALL		(V_SCD_TRSEQ_EVENT1(K_SCD_TRSEQ_IGNORED) | \
+					 V_SCD_TRSEQ_EVENT2(K_SCD_TRSEQ_IGNORED) | \
+					 V_SCD_TRSEQ_EVENT3(K_SCD_TRSEQ_IGNORED) | \
+					 V_SCD_TRSEQ_EVENT4(K_SCD_TRSEQ_IGNORED))
+
+#define S_SCD_TRSEQ_FUNCTION		16
+#define M_SCD_TRSEQ_FUNCTION		_SB_MAKEMASK(4, S_SCD_TRSEQ_FUNCTION)
+#define V_SCD_TRSEQ_FUNCTION(x)		_SB_MAKEVALUE(x, S_SCD_TRSEQ_FUNCTION)
+#define G_SCD_TRSEQ_FUNCTION(x)		_SB_GETVALUE(x, S_SCD_TRSEQ_FUNCTION, M_SCD_TRSEQ_FUNCTION)
+
+#define K_SCD_TRSEQ_FUNC_NOP		0
+#define K_SCD_TRSEQ_FUNC_START		1
+#define K_SCD_TRSEQ_FUNC_STOP		2
+#define K_SCD_TRSEQ_FUNC_FREEZE		3
+
+#define V_SCD_TRSEQ_FUNC_NOP		V_SCD_TRSEQ_FUNCTION(K_SCD_TRSEQ_FUNC_NOP)
+#define V_SCD_TRSEQ_FUNC_START		V_SCD_TRSEQ_FUNCTION(K_SCD_TRSEQ_FUNC_START)
+#define V_SCD_TRSEQ_FUNC_STOP		V_SCD_TRSEQ_FUNCTION(K_SCD_TRSEQ_FUNC_STOP)
+#define V_SCD_TRSEQ_FUNC_FREEZE		V_SCD_TRSEQ_FUNCTION(K_SCD_TRSEQ_FUNC_FREEZE)
+
+#define M_SCD_TRSEQ_ASAMPLE		_SB_MAKEMASK1(18)
+#define M_SCD_TRSEQ_DSAMPLE		_SB_MAKEMASK1(19)
+#define M_SCD_TRSEQ_DEBUGPIN		_SB_MAKEMASK1(20)
+#define M_SCD_TRSEQ_DEBUGCPU		_SB_MAKEMASK1(21)
+#define M_SCD_TRSEQ_CLEARUSE		_SB_MAKEMASK1(22)
+#define M_SCD_TRSEQ_ALLD_A		_SB_MAKEMASK1(23)
+#define M_SCD_TRSEQ_ALL_A		_SB_MAKEMASK1(24)
+
+#endif
diff --git a/arch/mips/include/asm/sibyte/sb1250_smbus.h b/arch/mips/include/asm/sibyte/sb1250_smbus.h
new file mode 100644
index 000000000..e854f96ff
--- /dev/null
+++ b/arch/mips/include/asm/sibyte/sb1250_smbus.h
@@ -0,0 +1,191 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*  *********************************************************************
+    *  SB1250 Board Support Package
+    *
+    *  SMBUS Constants				File: sb1250_smbus.h
+    *
+    *  This module contains constants and macros useful for
+    *  manipulating the SB1250's SMbus devices.
+    *
+    *  SB1250 specification level:  10/21/02
+    *  BCM1280 specification level:  11/24/03
+    *
+    *********************************************************************
+    *
+    *  Copyright 2000,2001,2002,2003
+    *  Broadcom Corporation. All rights reserved.
+    *
+    ********************************************************************* */
+
+
+#ifndef _SB1250_SMBUS_H
+#define _SB1250_SMBUS_H
+
+#include <asm/sibyte/sb1250_defs.h>
+
+/*
+ * SMBus Clock Frequency Register (Table 14-2)
+ */
+
+#define S_SMB_FREQ_DIV		    0
+#define M_SMB_FREQ_DIV		    _SB_MAKEMASK(13, S_SMB_FREQ_DIV)
+#define V_SMB_FREQ_DIV(x)	    _SB_MAKEVALUE(x, S_SMB_FREQ_DIV)
+
+#define K_SMB_FREQ_400KHZ	    0x1F
+#define K_SMB_FREQ_100KHZ	    0x7D
+#define K_SMB_FREQ_10KHZ	    1250
+
+#define S_SMB_CMD		    0
+#define M_SMB_CMD		    _SB_MAKEMASK(8, S_SMB_CMD)
+#define V_SMB_CMD(x)		    _SB_MAKEVALUE(x, S_SMB_CMD)
+
+/*
+ * SMBus control register (Table 14-4)
+ */
+
+#define M_SMB_ERR_INTR		    _SB_MAKEMASK1(0)
+#define M_SMB_FINISH_INTR	    _SB_MAKEMASK1(1)
+
+#define S_SMB_DATA_OUT		    4
+#define M_SMB_DATA_OUT		    _SB_MAKEMASK1(S_SMB_DATA_OUT)
+#define V_SMB_DATA_OUT(x)	    _SB_MAKEVALUE(x, S_SMB_DATA_OUT)
+
+#define M_SMB_DATA_DIR		    _SB_MAKEMASK1(5)
+#define M_SMB_DATA_DIR_OUTPUT	    M_SMB_DATA_DIR
+#define M_SMB_CLK_OUT		    _SB_MAKEMASK1(6)
+#define M_SMB_DIRECT_ENABLE	    _SB_MAKEMASK1(7)
+
+/*
+ * SMBus status registers (Table 14-5)
+ */
+
+#define M_SMB_BUSY		    _SB_MAKEMASK1(0)
+#define M_SMB_ERROR		    _SB_MAKEMASK1(1)
+#define M_SMB_ERROR_TYPE	    _SB_MAKEMASK1(2)
+
+#if SIBYTE_HDR_FEATURE(1250, PASS3) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+#define S_SMB_SCL_IN		    5
+#define M_SMB_SCL_IN		    _SB_MAKEMASK1(S_SMB_SCL_IN)
+#define V_SMB_SCL_IN(x)		    _SB_MAKEVALUE(x, S_SMB_SCL_IN)
+#define G_SMB_SCL_IN(x)		    _SB_GETVALUE(x, S_SMB_SCL_IN, M_SMB_SCL_IN)
+#endif /* 1250 PASS3 || 112x PASS1 || 1480 */
+
+#define S_SMB_REF		    6
+#define M_SMB_REF		    _SB_MAKEMASK1(S_SMB_REF)
+#define V_SMB_REF(x)		    _SB_MAKEVALUE(x, S_SMB_REF)
+#define G_SMB_REF(x)		    _SB_GETVALUE(x, S_SMB_REF, M_SMB_REF)
+
+#define S_SMB_DATA_IN		    7
+#define M_SMB_DATA_IN		    _SB_MAKEMASK1(S_SMB_DATA_IN)
+#define V_SMB_DATA_IN(x)	    _SB_MAKEVALUE(x, S_SMB_DATA_IN)
+#define G_SMB_DATA_IN(x)	    _SB_GETVALUE(x, S_SMB_DATA_IN, M_SMB_DATA_IN)
+
+/*
+ * SMBus Start/Command registers (Table 14-9)
+ */
+
+#define S_SMB_ADDR		    0
+#define M_SMB_ADDR		    _SB_MAKEMASK(7, S_SMB_ADDR)
+#define V_SMB_ADDR(x)		    _SB_MAKEVALUE(x, S_SMB_ADDR)
+#define G_SMB_ADDR(x)		    _SB_GETVALUE(x, S_SMB_ADDR, M_SMB_ADDR)
+
+#define M_SMB_QDATA		    _SB_MAKEMASK1(7)
+
+#define S_SMB_TT		    8
+#define M_SMB_TT		    _SB_MAKEMASK(3, S_SMB_TT)
+#define V_SMB_TT(x)		    _SB_MAKEVALUE(x, S_SMB_TT)
+#define G_SMB_TT(x)		    _SB_GETVALUE(x, S_SMB_TT, M_SMB_TT)
+
+#define K_SMB_TT_WR1BYTE	    0
+#define K_SMB_TT_WR2BYTE	    1
+#define K_SMB_TT_WR3BYTE	    2
+#define K_SMB_TT_CMD_RD1BYTE	    3
+#define K_SMB_TT_CMD_RD2BYTE	    4
+#define K_SMB_TT_RD1BYTE	    5
+#define K_SMB_TT_QUICKCMD	    6
+#define K_SMB_TT_EEPROMREAD	    7
+
+#define V_SMB_TT_WR1BYTE	    V_SMB_TT(K_SMB_TT_WR1BYTE)
+#define V_SMB_TT_WR2BYTE	    V_SMB_TT(K_SMB_TT_WR2BYTE)
+#define V_SMB_TT_WR3BYTE	    V_SMB_TT(K_SMB_TT_WR3BYTE)
+#define V_SMB_TT_CMD_RD1BYTE	    V_SMB_TT(K_SMB_TT_CMD_RD1BYTE)
+#define V_SMB_TT_CMD_RD2BYTE	    V_SMB_TT(K_SMB_TT_CMD_RD2BYTE)
+#define V_SMB_TT_RD1BYTE	    V_SMB_TT(K_SMB_TT_RD1BYTE)
+#define V_SMB_TT_QUICKCMD	    V_SMB_TT(K_SMB_TT_QUICKCMD)
+#define V_SMB_TT_EEPROMREAD	    V_SMB_TT(K_SMB_TT_EEPROMREAD)
+
+#define M_SMB_PEC		    _SB_MAKEMASK1(15)
+
+/*
+ * SMBus Data Register (Table 14-6) and SMBus Extra Register (Table 14-7)
+ */
+
+#define S_SMB_LB		    0
+#define M_SMB_LB		    _SB_MAKEMASK(8, S_SMB_LB)
+#define V_SMB_LB(x)		    _SB_MAKEVALUE(x, S_SMB_LB)
+
+#define S_SMB_MB		    8
+#define M_SMB_MB		    _SB_MAKEMASK(8, S_SMB_MB)
+#define V_SMB_MB(x)		    _SB_MAKEVALUE(x, S_SMB_MB)
+
+
+/*
+ * SMBus Packet Error Check register (Table 14-8)
+ */
+
+#define S_SPEC_PEC		    0
+#define M_SPEC_PEC		    _SB_MAKEMASK(8, S_SPEC_PEC)
+#define V_SPEC_MB(x)		    _SB_MAKEVALUE(x, S_SPEC_PEC)
+
+
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+
+#define S_SMB_CMDH		    8
+#define M_SMB_CMDH		    _SB_MAKEMASK(8, S_SMB_CMDH)
+#define V_SMB_CMDH(x)		    _SB_MAKEVALUE(x, S_SMB_CMDH)
+
+#define M_SMB_EXTEND		    _SB_MAKEMASK1(14)
+
+#define S_SMB_DFMT		    8
+#define M_SMB_DFMT		    _SB_MAKEMASK(3, S_SMB_DFMT)
+#define V_SMB_DFMT(x)		    _SB_MAKEVALUE(x, S_SMB_DFMT)
+#define G_SMB_DFMT(x)		    _SB_GETVALUE(x, S_SMB_DFMT, M_SMB_DFMT)
+
+#define K_SMB_DFMT_1BYTE	    0
+#define K_SMB_DFMT_2BYTE	    1
+#define K_SMB_DFMT_3BYTE	    2
+#define K_SMB_DFMT_4BYTE	    3
+#define K_SMB_DFMT_NODATA	    4
+#define K_SMB_DFMT_CMD4BYTE	    5
+#define K_SMB_DFMT_CMD5BYTE	    6
+#define K_SMB_DFMT_RESERVED	    7
+
+#define V_SMB_DFMT_1BYTE	    V_SMB_DFMT(K_SMB_DFMT_1BYTE)
+#define V_SMB_DFMT_2BYTE	    V_SMB_DFMT(K_SMB_DFMT_2BYTE)
+#define V_SMB_DFMT_3BYTE	    V_SMB_DFMT(K_SMB_DFMT_3BYTE)
+#define V_SMB_DFMT_4BYTE	    V_SMB_DFMT(K_SMB_DFMT_4BYTE)
+#define V_SMB_DFMT_NODATA	    V_SMB_DFMT(K_SMB_DFMT_NODATA)
+#define V_SMB_DFMT_CMD4BYTE	    V_SMB_DFMT(K_SMB_DFMT_CMD4BYTE)
+#define V_SMB_DFMT_CMD5BYTE	    V_SMB_DFMT(K_SMB_DFMT_CMD5BYTE)
+#define V_SMB_DFMT_RESERVED	    V_SMB_DFMT(K_SMB_DFMT_RESERVED)
+
+#define S_SMB_AFMT		    11
+#define M_SMB_AFMT		    _SB_MAKEMASK(2, S_SMB_AFMT)
+#define V_SMB_AFMT(x)		    _SB_MAKEVALUE(x, S_SMB_AFMT)
+#define G_SMB_AFMT(x)		    _SB_GETVALUE(x, S_SMB_AFMT, M_SMB_AFMT)
+
+#define K_SMB_AFMT_NONE		    0
+#define K_SMB_AFMT_ADDR		    1
+#define K_SMB_AFMT_ADDR_CMD1BYTE    2
+#define K_SMB_AFMT_ADDR_CMD2BYTE    3
+
+#define V_SMB_AFMT_NONE		    V_SMB_AFMT(K_SMB_AFMT_NONE)
+#define V_SMB_AFMT_ADDR		    V_SMB_AFMT(K_SMB_AFMT_ADDR)
+#define V_SMB_AFMT_ADDR_CMD1BYTE    V_SMB_AFMT(K_SMB_AFMT_ADDR_CMD1BYTE)
+#define V_SMB_AFMT_ADDR_CMD2BYTE    V_SMB_AFMT(K_SMB_AFMT_ADDR_CMD2BYTE)
+
+#define M_SMB_DIR		    _SB_MAKEMASK1(13)
+
+#endif /* 1250 PASS2 || 112x PASS1 || 1480 */
+
+#endif
diff --git a/arch/mips/include/asm/sibyte/sb1250_syncser.h b/arch/mips/include/asm/sibyte/sb1250_syncser.h
new file mode 100644
index 000000000..8b40e3f05
--- /dev/null
+++ b/arch/mips/include/asm/sibyte/sb1250_syncser.h
@@ -0,0 +1,133 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*  *********************************************************************
+    *  SB1250 Board Support Package
+    *
+    *  Synchronous Serial Constants		 File: sb1250_syncser.h
+    *
+    *  This module contains constants and macros useful for
+    *  manipulating the SB1250's Synchronous Serial
+    *
+    *  SB1250 specification level:  User's manual 1/02/02
+    *
+    *********************************************************************
+    *
+    *  Copyright 2000,2001,2002,2003
+    *  Broadcom Corporation. All rights reserved.
+    *
+    ********************************************************************* */
+
+
+#ifndef _SB1250_SYNCSER_H
+#define _SB1250_SYNCSER_H
+
+#include <asm/sibyte/sb1250_defs.h>
+
+/*
+ * Serial Mode Configuration Register
+ */
+
+#define M_SYNCSER_CRC_MODE		   _SB_MAKEMASK1(0)
+#define M_SYNCSER_MSB_FIRST		   _SB_MAKEMASK1(1)
+
+#define S_SYNCSER_FLAG_NUM		   2
+#define M_SYNCSER_FLAG_NUM		   _SB_MAKEMASK(4, S_SYNCSER_FLAG_NUM)
+#define V_SYNCSER_FLAG_NUM		   _SB_MAKEVALUE(x, S_SYNCSER_FLAG_NUM)
+
+#define M_SYNCSER_FLAG_EN		   _SB_MAKEMASK1(6)
+#define M_SYNCSER_HDLC_EN		   _SB_MAKEMASK1(7)
+#define M_SYNCSER_LOOP_MODE		   _SB_MAKEMASK1(8)
+#define M_SYNCSER_LOOPBACK		   _SB_MAKEMASK1(9)
+
+/*
+ * Serial Clock Source and Line Interface Mode Register
+ */
+
+#define M_SYNCSER_RXCLK_INV		   _SB_MAKEMASK1(0)
+#define M_SYNCSER_RXCLK_EXT		   _SB_MAKEMASK1(1)
+
+#define S_SYNCSER_RXSYNC_DLY		   2
+#define M_SYNCSER_RXSYNC_DLY		   _SB_MAKEMASK(2, S_SYNCSER_RXSYNC_DLY)
+#define V_SYNCSER_RXSYNC_DLY(x)		   _SB_MAKEVALUE(x, S_SYNCSER_RXSYNC_DLY)
+
+#define M_SYNCSER_RXSYNC_LOW		   _SB_MAKEMASK1(4)
+#define M_SYNCSER_RXSTRB_LOW		   _SB_MAKEMASK1(5)
+
+#define M_SYNCSER_RXSYNC_EDGE		   _SB_MAKEMASK1(6)
+#define M_SYNCSER_RXSYNC_INT		   _SB_MAKEMASK1(7)
+
+#define M_SYNCSER_TXCLK_INV		   _SB_MAKEMASK1(8)
+#define M_SYNCSER_TXCLK_EXT		   _SB_MAKEMASK1(9)
+
+#define S_SYNCSER_TXSYNC_DLY		   10
+#define M_SYNCSER_TXSYNC_DLY		   _SB_MAKEMASK(2, S_SYNCSER_TXSYNC_DLY)
+#define V_SYNCSER_TXSYNC_DLY(x)		   _SB_MAKEVALUE(x, S_SYNCSER_TXSYNC_DLY)
+
+#define M_SYNCSER_TXSYNC_LOW		   _SB_MAKEMASK1(12)
+#define M_SYNCSER_TXSTRB_LOW		   _SB_MAKEMASK1(13)
+
+#define M_SYNCSER_TXSYNC_EDGE		   _SB_MAKEMASK1(14)
+#define M_SYNCSER_TXSYNC_INT		   _SB_MAKEMASK1(15)
+
+/*
+ * Serial Command Register
+ */
+
+#define M_SYNCSER_CMD_RX_EN		   _SB_MAKEMASK1(0)
+#define M_SYNCSER_CMD_TX_EN		   _SB_MAKEMASK1(1)
+#define M_SYNCSER_CMD_RX_RESET		   _SB_MAKEMASK1(2)
+#define M_SYNCSER_CMD_TX_RESET		   _SB_MAKEMASK1(3)
+#define M_SYNCSER_CMD_TX_PAUSE		   _SB_MAKEMASK1(5)
+
+/*
+ * Serial DMA Enable Register
+ */
+
+#define M_SYNCSER_DMA_RX_EN		   _SB_MAKEMASK1(0)
+#define M_SYNCSER_DMA_TX_EN		   _SB_MAKEMASK1(4)
+
+/*
+ * Serial Status Register
+ */
+
+#define M_SYNCSER_RX_CRCERR		   _SB_MAKEMASK1(0)
+#define M_SYNCSER_RX_ABORT		   _SB_MAKEMASK1(1)
+#define M_SYNCSER_RX_OCTET		   _SB_MAKEMASK1(2)
+#define M_SYNCSER_RX_LONGFRM		   _SB_MAKEMASK1(3)
+#define M_SYNCSER_RX_SHORTFRM		   _SB_MAKEMASK1(4)
+#define M_SYNCSER_RX_OVERRUN		   _SB_MAKEMASK1(5)
+#define M_SYNCSER_RX_SYNC_ERR		   _SB_MAKEMASK1(6)
+#define M_SYNCSER_TX_CRCERR		   _SB_MAKEMASK1(8)
+#define M_SYNCSER_TX_UNDERRUN		   _SB_MAKEMASK1(9)
+#define M_SYNCSER_TX_SYNC_ERR		   _SB_MAKEMASK1(10)
+#define M_SYNCSER_TX_PAUSE_COMPLETE	   _SB_MAKEMASK1(11)
+#define M_SYNCSER_RX_EOP_COUNT		   _SB_MAKEMASK1(16)
+#define M_SYNCSER_RX_EOP_TIMER		   _SB_MAKEMASK1(17)
+#define M_SYNCSER_RX_EOP_SEEN		   _SB_MAKEMASK1(18)
+#define M_SYNCSER_RX_HWM		   _SB_MAKEMASK1(19)
+#define M_SYNCSER_RX_LWM		   _SB_MAKEMASK1(20)
+#define M_SYNCSER_RX_DSCR		   _SB_MAKEMASK1(21)
+#define M_SYNCSER_RX_DERR		   _SB_MAKEMASK1(22)
+#define M_SYNCSER_TX_EOP_COUNT		   _SB_MAKEMASK1(24)
+#define M_SYNCSER_TX_EOP_TIMER		   _SB_MAKEMASK1(25)
+#define M_SYNCSER_TX_EOP_SEEN		   _SB_MAKEMASK1(26)
+#define M_SYNCSER_TX_HWM		   _SB_MAKEMASK1(27)
+#define M_SYNCSER_TX_LWM		   _SB_MAKEMASK1(28)
+#define M_SYNCSER_TX_DSCR		   _SB_MAKEMASK1(29)
+#define M_SYNCSER_TX_DERR		   _SB_MAKEMASK1(30)
+#define M_SYNCSER_TX_DZERO		   _SB_MAKEMASK1(31)
+
+/*
+ * Sequencer Table Entry format
+ */
+
+#define M_SYNCSER_SEQ_LAST		   _SB_MAKEMASK1(0)
+#define M_SYNCSER_SEQ_BYTE		   _SB_MAKEMASK1(1)
+
+#define S_SYNCSER_SEQ_COUNT		   2
+#define M_SYNCSER_SEQ_COUNT		   _SB_MAKEMASK(4, S_SYNCSER_SEQ_COUNT)
+#define V_SYNCSER_SEQ_COUNT(x)		   _SB_MAKEVALUE(x, S_SYNCSER_SEQ_COUNT)
+
+#define M_SYNCSER_SEQ_ENABLE		   _SB_MAKEMASK1(6)
+#define M_SYNCSER_SEQ_STROBE		   _SB_MAKEMASK1(7)
+
+#endif
diff --git a/arch/mips/include/asm/sibyte/sb1250_uart.h b/arch/mips/include/asm/sibyte/sb1250_uart.h
new file mode 100644
index 000000000..da782e643
--- /dev/null
+++ b/arch/mips/include/asm/sibyte/sb1250_uart.h
@@ -0,0 +1,349 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*  *********************************************************************
+    *  SB1250 Board Support Package
+    *
+    *  UART Constants				File: sb1250_uart.h
+    *
+    *  This module contains constants and macros useful for
+    *  manipulating the SB1250's UARTs
+    *
+    *  SB1250 specification level:  User's manual 1/02/02
+    *
+    *********************************************************************
+    *
+    *  Copyright 2000,2001,2002,2003
+    *  Broadcom Corporation. All rights reserved.
+    *
+    ********************************************************************* */
+
+
+#ifndef _SB1250_UART_H
+#define _SB1250_UART_H
+
+#include <asm/sibyte/sb1250_defs.h>
+
+/* **********************************************************************
+   * DUART Registers
+   ********************************************************************** */
+
+/*
+ * DUART Mode Register #1 (Table 10-3)
+ * Register: DUART_MODE_REG_1_A
+ * Register: DUART_MODE_REG_1_B
+ */
+
+#define S_DUART_BITS_PER_CHAR	    0
+#define M_DUART_BITS_PER_CHAR	    _SB_MAKEMASK(2, S_DUART_BITS_PER_CHAR)
+#define V_DUART_BITS_PER_CHAR(x)    _SB_MAKEVALUE(x, S_DUART_BITS_PER_CHAR)
+
+#define K_DUART_BITS_PER_CHAR_RSV0  0
+#define K_DUART_BITS_PER_CHAR_RSV1  1
+#define K_DUART_BITS_PER_CHAR_7	    2
+#define K_DUART_BITS_PER_CHAR_8	    3
+
+#define V_DUART_BITS_PER_CHAR_RSV0  V_DUART_BITS_PER_CHAR(K_DUART_BITS_PER_CHAR_RSV0)
+#define V_DUART_BITS_PER_CHAR_RSV1  V_DUART_BITS_PER_CHAR(K_DUART_BITS_PER_CHAR_RSV1)
+#define V_DUART_BITS_PER_CHAR_7	    V_DUART_BITS_PER_CHAR(K_DUART_BITS_PER_CHAR_7)
+#define V_DUART_BITS_PER_CHAR_8	    V_DUART_BITS_PER_CHAR(K_DUART_BITS_PER_CHAR_8)
+
+
+#define M_DUART_PARITY_TYPE_EVEN    0x00
+#define M_DUART_PARITY_TYPE_ODD	    _SB_MAKEMASK1(2)
+
+#define S_DUART_PARITY_MODE	     3
+#define M_DUART_PARITY_MODE	    _SB_MAKEMASK(2, S_DUART_PARITY_MODE)
+#define V_DUART_PARITY_MODE(x)	    _SB_MAKEVALUE(x, S_DUART_PARITY_MODE)
+
+#define K_DUART_PARITY_MODE_ADD	      0
+#define K_DUART_PARITY_MODE_ADD_FIXED 1
+#define K_DUART_PARITY_MODE_NONE      2
+
+#define V_DUART_PARITY_MODE_ADD	      V_DUART_PARITY_MODE(K_DUART_PARITY_MODE_ADD)
+#define V_DUART_PARITY_MODE_ADD_FIXED V_DUART_PARITY_MODE(K_DUART_PARITY_MODE_ADD_FIXED)
+#define V_DUART_PARITY_MODE_NONE      V_DUART_PARITY_MODE(K_DUART_PARITY_MODE_NONE)
+
+#define M_DUART_TX_IRQ_SEL_TXRDY    0
+#define M_DUART_TX_IRQ_SEL_TXEMPT   _SB_MAKEMASK1(5)
+
+#define M_DUART_RX_IRQ_SEL_RXRDY    0
+#define M_DUART_RX_IRQ_SEL_RXFULL   _SB_MAKEMASK1(6)
+
+#define M_DUART_RX_RTS_ENA	    _SB_MAKEMASK1(7)
+
+/*
+ * DUART Mode Register #2 (Table 10-4)
+ * Register: DUART_MODE_REG_2_A
+ * Register: DUART_MODE_REG_2_B
+ */
+
+#define M_DUART_MODE_RESERVED1	    _SB_MAKEMASK(3, 0)	 /* ignored */
+
+#define M_DUART_STOP_BIT_LEN_2	    _SB_MAKEMASK1(3)
+#define M_DUART_STOP_BIT_LEN_1	    0
+
+#define M_DUART_TX_CTS_ENA	    _SB_MAKEMASK1(4)
+
+
+#define M_DUART_MODE_RESERVED2	    _SB_MAKEMASK1(5)	/* must be zero */
+
+#define S_DUART_CHAN_MODE	    6
+#define M_DUART_CHAN_MODE	    _SB_MAKEMASK(2, S_DUART_CHAN_MODE)
+#define V_DUART_CHAN_MODE(x)	    _SB_MAKEVALUE(x, S_DUART_CHAN_MODE)
+
+#define K_DUART_CHAN_MODE_NORMAL    0
+#define K_DUART_CHAN_MODE_LCL_LOOP  2
+#define K_DUART_CHAN_MODE_REM_LOOP  3
+
+#define V_DUART_CHAN_MODE_NORMAL    V_DUART_CHAN_MODE(K_DUART_CHAN_MODE_NORMAL)
+#define V_DUART_CHAN_MODE_LCL_LOOP  V_DUART_CHAN_MODE(K_DUART_CHAN_MODE_LCL_LOOP)
+#define V_DUART_CHAN_MODE_REM_LOOP  V_DUART_CHAN_MODE(K_DUART_CHAN_MODE_REM_LOOP)
+
+/*
+ * DUART Command Register (Table 10-5)
+ * Register: DUART_CMD_A
+ * Register: DUART_CMD_B
+ */
+
+#define M_DUART_RX_EN		    _SB_MAKEMASK1(0)
+#define M_DUART_RX_DIS		    _SB_MAKEMASK1(1)
+#define M_DUART_TX_EN		    _SB_MAKEMASK1(2)
+#define M_DUART_TX_DIS		    _SB_MAKEMASK1(3)
+
+#define S_DUART_MISC_CMD	    4
+#define M_DUART_MISC_CMD	    _SB_MAKEMASK(3, S_DUART_MISC_CMD)
+#define V_DUART_MISC_CMD(x)	    _SB_MAKEVALUE(x, S_DUART_MISC_CMD)
+
+#define K_DUART_MISC_CMD_NOACTION0	 0
+#define K_DUART_MISC_CMD_NOACTION1	 1
+#define K_DUART_MISC_CMD_RESET_RX	 2
+#define K_DUART_MISC_CMD_RESET_TX	 3
+#define K_DUART_MISC_CMD_NOACTION4	 4
+#define K_DUART_MISC_CMD_RESET_BREAK_INT 5
+#define K_DUART_MISC_CMD_START_BREAK	 6
+#define K_DUART_MISC_CMD_STOP_BREAK	 7
+
+#define V_DUART_MISC_CMD_NOACTION0	 V_DUART_MISC_CMD(K_DUART_MISC_CMD_NOACTION0)
+#define V_DUART_MISC_CMD_NOACTION1	 V_DUART_MISC_CMD(K_DUART_MISC_CMD_NOACTION1)
+#define V_DUART_MISC_CMD_RESET_RX	 V_DUART_MISC_CMD(K_DUART_MISC_CMD_RESET_RX)
+#define V_DUART_MISC_CMD_RESET_TX	 V_DUART_MISC_CMD(K_DUART_MISC_CMD_RESET_TX)
+#define V_DUART_MISC_CMD_NOACTION4	 V_DUART_MISC_CMD(K_DUART_MISC_CMD_NOACTION4)
+#define V_DUART_MISC_CMD_RESET_BREAK_INT V_DUART_MISC_CMD(K_DUART_MISC_CMD_RESET_BREAK_INT)
+#define V_DUART_MISC_CMD_START_BREAK	 V_DUART_MISC_CMD(K_DUART_MISC_CMD_START_BREAK)
+#define V_DUART_MISC_CMD_STOP_BREAK	 V_DUART_MISC_CMD(K_DUART_MISC_CMD_STOP_BREAK)
+
+#define M_DUART_CMD_RESERVED		 _SB_MAKEMASK1(7)
+
+/*
+ * DUART Status Register (Table 10-6)
+ * Register: DUART_STATUS_A
+ * Register: DUART_STATUS_B
+ * READ-ONLY
+ */
+
+#define M_DUART_RX_RDY		    _SB_MAKEMASK1(0)
+#define M_DUART_RX_FFUL		    _SB_MAKEMASK1(1)
+#define M_DUART_TX_RDY		    _SB_MAKEMASK1(2)
+#define M_DUART_TX_EMT		    _SB_MAKEMASK1(3)
+#define M_DUART_OVRUN_ERR	    _SB_MAKEMASK1(4)
+#define M_DUART_PARITY_ERR	    _SB_MAKEMASK1(5)
+#define M_DUART_FRM_ERR		    _SB_MAKEMASK1(6)
+#define M_DUART_RCVD_BRK	    _SB_MAKEMASK1(7)
+
+/*
+ * DUART Baud Rate Register (Table 10-7)
+ * Register: DUART_CLK_SEL_A
+ * Register: DUART_CLK_SEL_B
+ */
+
+#define M_DUART_CLK_COUNTER	    _SB_MAKEMASK(12, 0)
+#define V_DUART_BAUD_RATE(x)	    (100000000/((x)*20)-1)
+
+/*
+ * DUART Data Registers (Table 10-8 and 10-9)
+ * Register: DUART_RX_HOLD_A
+ * Register: DUART_RX_HOLD_B
+ * Register: DUART_TX_HOLD_A
+ * Register: DUART_TX_HOLD_B
+ */
+
+#define M_DUART_RX_DATA		    _SB_MAKEMASK(8, 0)
+#define M_DUART_TX_DATA		    _SB_MAKEMASK(8, 0)
+
+/*
+ * DUART Input Port Register (Table 10-10)
+ * Register: DUART_IN_PORT
+ */
+
+#define M_DUART_IN_PIN0_VAL	    _SB_MAKEMASK1(0)
+#define M_DUART_IN_PIN1_VAL	    _SB_MAKEMASK1(1)
+#define M_DUART_IN_PIN2_VAL	    _SB_MAKEMASK1(2)
+#define M_DUART_IN_PIN3_VAL	    _SB_MAKEMASK1(3)
+#define M_DUART_IN_PIN4_VAL	    _SB_MAKEMASK1(4)
+#define M_DUART_IN_PIN5_VAL	    _SB_MAKEMASK1(5)
+#define M_DUART_RIN0_PIN	    _SB_MAKEMASK1(6)
+#define M_DUART_RIN1_PIN	    _SB_MAKEMASK1(7)
+
+/*
+ * DUART Input Port Change Status Register (Tables 10-11, 10-12, and 10-13)
+ * Register: DUART_INPORT_CHNG
+ */
+
+#define S_DUART_IN_PIN_VAL	    0
+#define M_DUART_IN_PIN_VAL	    _SB_MAKEMASK(4, S_DUART_IN_PIN_VAL)
+
+#define S_DUART_IN_PIN_CHNG	    4
+#define M_DUART_IN_PIN_CHNG	    _SB_MAKEMASK(4, S_DUART_IN_PIN_CHNG)
+
+
+/*
+ * DUART Output port control register (Table 10-14)
+ * Register: DUART_OPCR
+ */
+
+#define M_DUART_OPCR_RESERVED0	    _SB_MAKEMASK1(0)   /* must be zero */
+#define M_DUART_OPC2_SEL	    _SB_MAKEMASK1(1)
+#define M_DUART_OPCR_RESERVED1	    _SB_MAKEMASK1(2)   /* must be zero */
+#define M_DUART_OPC3_SEL	    _SB_MAKEMASK1(3)
+#define M_DUART_OPCR_RESERVED2	    _SB_MAKEMASK(4, 4)	/* must be zero */
+
+/*
+ * DUART Aux Control Register (Table 10-15)
+ * Register: DUART_AUX_CTRL
+ */
+
+#define M_DUART_IP0_CHNG_ENA	    _SB_MAKEMASK1(0)
+#define M_DUART_IP1_CHNG_ENA	    _SB_MAKEMASK1(1)
+#define M_DUART_IP2_CHNG_ENA	    _SB_MAKEMASK1(2)
+#define M_DUART_IP3_CHNG_ENA	    _SB_MAKEMASK1(3)
+#define M_DUART_ACR_RESERVED	    _SB_MAKEMASK(4, 4)
+
+#define M_DUART_CTS_CHNG_ENA	    _SB_MAKEMASK1(0)
+#define M_DUART_CIN_CHNG_ENA	    _SB_MAKEMASK1(2)
+
+/*
+ * DUART Interrupt Status Register (Table 10-16)
+ * Register: DUART_ISR
+ */
+
+#define M_DUART_ISR_TX_A	    _SB_MAKEMASK1(0)
+
+#define S_DUART_ISR_RX_A	    1
+#define M_DUART_ISR_RX_A	    _SB_MAKEMASK1(S_DUART_ISR_RX_A)
+#define V_DUART_ISR_RX_A(x)	    _SB_MAKEVALUE(x, S_DUART_ISR_RX_A)
+#define G_DUART_ISR_RX_A(x)	    _SB_GETVALUE(x, S_DUART_ISR_RX_A, M_DUART_ISR_RX_A)
+
+#define M_DUART_ISR_BRK_A	    _SB_MAKEMASK1(2)
+#define M_DUART_ISR_IN_A	    _SB_MAKEMASK1(3)
+#define M_DUART_ISR_ALL_A	    _SB_MAKEMASK(4, 0)
+
+#define M_DUART_ISR_TX_B	    _SB_MAKEMASK1(4)
+#define M_DUART_ISR_RX_B	    _SB_MAKEMASK1(5)
+#define M_DUART_ISR_BRK_B	    _SB_MAKEMASK1(6)
+#define M_DUART_ISR_IN_B	    _SB_MAKEMASK1(7)
+#define M_DUART_ISR_ALL_B	    _SB_MAKEMASK(4, 4)
+
+/*
+ * DUART Channel A Interrupt Status Register (Table 10-17)
+ * DUART Channel B Interrupt Status Register (Table 10-18)
+ * Register: DUART_ISR_A
+ * Register: DUART_ISR_B
+ */
+
+#define M_DUART_ISR_TX		    _SB_MAKEMASK1(0)
+#define M_DUART_ISR_RX		    _SB_MAKEMASK1(1)
+#define M_DUART_ISR_BRK		    _SB_MAKEMASK1(2)
+#define M_DUART_ISR_IN		    _SB_MAKEMASK1(3)
+#define M_DUART_ISR_ALL		    _SB_MAKEMASK(4, 0)
+#define M_DUART_ISR_RESERVED	    _SB_MAKEMASK(4, 4)
+
+/*
+ * DUART Interrupt Mask Register (Table 10-19)
+ * Register: DUART_IMR
+ */
+
+#define M_DUART_IMR_TX_A	    _SB_MAKEMASK1(0)
+#define M_DUART_IMR_RX_A	    _SB_MAKEMASK1(1)
+#define M_DUART_IMR_BRK_A	    _SB_MAKEMASK1(2)
+#define M_DUART_IMR_IN_A	    _SB_MAKEMASK1(3)
+#define M_DUART_IMR_ALL_A	    _SB_MAKEMASK(4, 0)
+
+#define M_DUART_IMR_TX_B	    _SB_MAKEMASK1(4)
+#define M_DUART_IMR_RX_B	    _SB_MAKEMASK1(5)
+#define M_DUART_IMR_BRK_B	    _SB_MAKEMASK1(6)
+#define M_DUART_IMR_IN_B	    _SB_MAKEMASK1(7)
+#define M_DUART_IMR_ALL_B	    _SB_MAKEMASK(4, 4)
+
+/*
+ * DUART Channel A Interrupt Mask Register (Table 10-20)
+ * DUART Channel B Interrupt Mask Register (Table 10-21)
+ * Register: DUART_IMR_A
+ * Register: DUART_IMR_B
+ */
+
+#define M_DUART_IMR_TX		    _SB_MAKEMASK1(0)
+#define M_DUART_IMR_RX		    _SB_MAKEMASK1(1)
+#define M_DUART_IMR_BRK		    _SB_MAKEMASK1(2)
+#define M_DUART_IMR_IN		    _SB_MAKEMASK1(3)
+#define M_DUART_IMR_ALL		    _SB_MAKEMASK(4, 0)
+#define M_DUART_IMR_RESERVED	    _SB_MAKEMASK(4, 4)
+
+
+/*
+ * DUART Output Port Set Register (Table 10-22)
+ * Register: DUART_SET_OPR
+ */
+
+#define M_DUART_SET_OPR0	    _SB_MAKEMASK1(0)
+#define M_DUART_SET_OPR1	    _SB_MAKEMASK1(1)
+#define M_DUART_SET_OPR2	    _SB_MAKEMASK1(2)
+#define M_DUART_SET_OPR3	    _SB_MAKEMASK1(3)
+#define M_DUART_OPSR_RESERVED	    _SB_MAKEMASK(4, 4)
+
+/*
+ * DUART Output Port Clear Register (Table 10-23)
+ * Register: DUART_CLEAR_OPR
+ */
+
+#define M_DUART_CLR_OPR0	    _SB_MAKEMASK1(0)
+#define M_DUART_CLR_OPR1	    _SB_MAKEMASK1(1)
+#define M_DUART_CLR_OPR2	    _SB_MAKEMASK1(2)
+#define M_DUART_CLR_OPR3	    _SB_MAKEMASK1(3)
+#define M_DUART_OPCR_RESERVED	    _SB_MAKEMASK(4, 4)
+
+/*
+ * DUART Output Port RTS Register (Table 10-24)
+ * Register: DUART_OUT_PORT
+ */
+
+#define M_DUART_OUT_PIN_SET0	    _SB_MAKEMASK1(0)
+#define M_DUART_OUT_PIN_SET1	    _SB_MAKEMASK1(1)
+#define M_DUART_OUT_PIN_CLR0	    _SB_MAKEMASK1(2)
+#define M_DUART_OUT_PIN_CLR1	    _SB_MAKEMASK1(3)
+#define M_DUART_OPRR_RESERVED	    _SB_MAKEMASK(4, 4)
+
+#define M_DUART_OUT_PIN_SET(chan) \
+    (chan == 0 ? M_DUART_OUT_PIN_SET0 : M_DUART_OUT_PIN_SET1)
+#define M_DUART_OUT_PIN_CLR(chan) \
+    (chan == 0 ? M_DUART_OUT_PIN_CLR0 : M_DUART_OUT_PIN_CLR1)
+
+#if SIBYTE_HDR_FEATURE(1250, PASS2) || SIBYTE_HDR_FEATURE(112x, PASS1) || SIBYTE_HDR_FEATURE_CHIP(1480)
+/*
+ * Full Interrupt Control Register
+ */
+
+#define S_DUART_SIG_FULL	   _SB_MAKE64(0)
+#define M_DUART_SIG_FULL	   _SB_MAKEMASK(4, S_DUART_SIG_FULL)
+#define V_DUART_SIG_FULL(x)	   _SB_MAKEVALUE(x, S_DUART_SIG_FULL)
+#define G_DUART_SIG_FULL(x)	   _SB_GETVALUE(x, S_DUART_SIG_FULL, M_DUART_SIG_FULL)
+
+#define S_DUART_INT_TIME	   _SB_MAKE64(4)
+#define M_DUART_INT_TIME	   _SB_MAKEMASK(4, S_DUART_INT_TIME)
+#define V_DUART_INT_TIME(x)	   _SB_MAKEVALUE(x, S_DUART_INT_TIME)
+#define G_DUART_INT_TIME(x)	   _SB_GETVALUE(x, S_DUART_INT_TIME, M_DUART_INT_TIME)
+#endif /* 1250 PASS2 || 112x PASS1 || 1480 */
+
+
+/* ********************************************************************** */
+
+
+#endif
diff --git a/arch/mips/include/asm/sibyte/sentosa.h b/arch/mips/include/asm/sibyte/sentosa.h
new file mode 100644
index 000000000..a27cda344
--- /dev/null
+++ b/arch/mips/include/asm/sibyte/sentosa.h
@@ -0,0 +1,27 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2000, 2001 Broadcom Corporation
+ */
+#ifndef __ASM_SIBYTE_SENTOSA_H
+#define __ASM_SIBYTE_SENTOSA_H
+
+#include <asm/sibyte/sb1250.h>
+#include <asm/sibyte/sb1250_int.h>
+
+#ifdef CONFIG_SIBYTE_SENTOSA
+#define SIBYTE_BOARD_NAME "BCM91250E (Sentosa)"
+#endif
+#ifdef CONFIG_SIBYTE_RHONE
+#define SIBYTE_BOARD_NAME "BCM91125E (Rhone)"
+#endif
+
+/* Generic bus chip selects */
+#ifdef CONFIG_SIBYTE_RHONE
+#define LEDS_CS		6
+#define LEDS_PHYS	0x1d0a0000
+#endif
+
+/* GPIOs */
+#define K_GPIO_DBG_LED	0
+
+#endif /* __ASM_SIBYTE_SENTOSA_H */
diff --git a/arch/mips/include/asm/sibyte/swarm.h b/arch/mips/include/asm/sibyte/swarm.h
new file mode 100644
index 000000000..947122f48
--- /dev/null
+++ b/arch/mips/include/asm/sibyte/swarm.h
@@ -0,0 +1,51 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2000, 2001, 2002, 2003 Broadcom Corporation
+ */
+#ifndef __ASM_SIBYTE_SWARM_H
+#define __ASM_SIBYTE_SWARM_H
+
+#include <asm/sibyte/sb1250.h>
+#include <asm/sibyte/sb1250_int.h>
+
+#ifdef CONFIG_SIBYTE_SWARM
+#define SIBYTE_BOARD_NAME "BCM91250A (SWARM)"
+#define SIBYTE_HAVE_PCMCIA 1
+#define SIBYTE_HAVE_IDE	   1
+#endif
+#ifdef CONFIG_SIBYTE_LITTLESUR
+#define SIBYTE_BOARD_NAME "BCM91250C2 (LittleSur)"
+#define SIBYTE_HAVE_PCMCIA 0
+#define SIBYTE_HAVE_IDE	   1
+#define SIBYTE_DEFAULT_CONSOLE "cfe0"
+#endif
+#ifdef CONFIG_SIBYTE_CRHONE
+#define SIBYTE_BOARD_NAME "BCM91125C (CRhone)"
+#define SIBYTE_HAVE_PCMCIA 0
+#define SIBYTE_HAVE_IDE	   0
+#endif
+#ifdef CONFIG_SIBYTE_CRHINE
+#define SIBYTE_BOARD_NAME "BCM91120C (CRhine)"
+#define SIBYTE_HAVE_PCMCIA 0
+#define SIBYTE_HAVE_IDE	   0
+#endif
+
+/* Generic bus chip selects */
+#define LEDS_CS		3
+#define LEDS_PHYS	0x100a0000
+
+#ifdef SIBYTE_HAVE_IDE
+#define IDE_CS		4
+#define IDE_PHYS	0x100b0000
+#define K_GPIO_GB_IDE	4
+#define K_INT_GB_IDE	(K_INT_GPIO_0 + K_GPIO_GB_IDE)
+#endif
+
+#ifdef SIBYTE_HAVE_PCMCIA
+#define PCMCIA_CS	6
+#define PCMCIA_PHYS	0x11000000
+#define K_GPIO_PC_READY 9
+#define K_INT_PC_READY	(K_INT_GPIO_0 + K_GPIO_PC_READY)
+#endif
+
+#endif /* __ASM_SIBYTE_SWARM_H */
diff --git a/arch/mips/include/asm/sigcontext.h b/arch/mips/include/asm/sigcontext.h
new file mode 100644
index 000000000..eeeb0f48c
--- /dev/null
+++ b/arch/mips/include/asm/sigcontext.h
@@ -0,0 +1,37 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1996, 1997, 1999 by Ralf Baechle
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_SIGCONTEXT_H
+#define _ASM_SIGCONTEXT_H
+
+#include <uapi/asm/sigcontext.h>
+
+#if _MIPS_SIM == _MIPS_SIM_ABI64 || _MIPS_SIM == _MIPS_SIM_NABI32
+
+struct sigcontext32 {
+	__u32		sc_regmask;	/* Unused */
+	__u32		sc_status;	/* Unused */
+	__u64		sc_pc;
+	__u64		sc_regs[32];
+	__u64		sc_fpregs[32];
+	__u32		sc_acx;		/* Only MIPS32; was sc_ownedfp */
+	__u32		sc_fpc_csr;
+	__u32		sc_fpc_eir;	/* Unused */
+	__u32		sc_used_math;
+	__u32		sc_dsp;		/* dsp status, was sc_ssflags */
+	__u64		sc_mdhi;
+	__u64		sc_mdlo;
+	__u32		sc_hi1;		/* Was sc_cause */
+	__u32		sc_lo1;		/* Was sc_badvaddr */
+	__u32		sc_hi2;		/* Was sc_sigset[4] */
+	__u32		sc_lo2;
+	__u32		sc_hi3;
+	__u32		sc_lo3;
+};
+#endif /* _MIPS_SIM == _MIPS_SIM_ABI64 || _MIPS_SIM == _MIPS_SIM_NABI32 */
+#endif /* _ASM_SIGCONTEXT_H */
diff --git a/arch/mips/include/asm/signal.h b/arch/mips/include/asm/signal.h
new file mode 100644
index 000000000..23d6b8015
--- /dev/null
+++ b/arch/mips/include/asm/signal.h
@@ -0,0 +1,35 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995, 96, 97, 98, 99, 2003 by Ralf Baechle
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_SIGNAL_H
+#define _ASM_SIGNAL_H
+
+#include <uapi/asm/signal.h>
+
+#ifdef CONFIG_MIPS32_O32
+extern struct mips_abi mips_abi_32;
+
+#define sig_uses_siginfo(ka, abi)                               \
+	((abi != &mips_abi_32) ? 1 :                            \
+		((ka)->sa.sa_flags & SA_SIGINFO))
+#else
+#define sig_uses_siginfo(ka, abi)                               \
+	(IS_ENABLED(CONFIG_64BIT) ? 1 :                     \
+		(IS_ENABLED(CONFIG_TRAD_SIGNALS) ?          \
+			((ka)->sa.sa_flags & SA_SIGINFO) : 1) )
+#endif
+
+#include <asm/sigcontext.h>
+#include <asm/siginfo.h>
+
+#define __ARCH_HAS_IRIX_SIGACTION
+
+extern int protected_save_fp_context(void __user *sc);
+extern int protected_restore_fp_context(void __user *sc);
+
+#endif /* _ASM_SIGNAL_H */
diff --git a/arch/mips/include/asm/sim.h b/arch/mips/include/asm/sim.h
new file mode 100644
index 000000000..59f31a95f
--- /dev/null
+++ b/arch/mips/include/asm/sim.h
@@ -0,0 +1,70 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1999, 2000, 2003 Ralf Baechle
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_SIM_H
+#define _ASM_SIM_H
+
+
+#include <asm/asm-offsets.h>
+
+#define __str2(x) #x
+#define __str(x) __str2(x)
+
+#ifdef CONFIG_32BIT
+
+#define save_static_function(symbol)					\
+__asm__(								\
+	".text\n\t"							\
+	".globl\t__" #symbol "\n\t"					\
+	".align\t2\n\t"							\
+	".type\t__" #symbol ", @function\n\t"				\
+	".ent\t__" #symbol ", 0\n__"					\
+	#symbol":\n\t"							\
+	".frame\t$29, 0, $31\n\t"					\
+	"sw\t$16,"__str(PT_R16)"($29)\t\t\t# save_static_function\n\t"	\
+	"sw\t$17,"__str(PT_R17)"($29)\n\t"				\
+	"sw\t$18,"__str(PT_R18)"($29)\n\t"				\
+	"sw\t$19,"__str(PT_R19)"($29)\n\t"				\
+	"sw\t$20,"__str(PT_R20)"($29)\n\t"				\
+	"sw\t$21,"__str(PT_R21)"($29)\n\t"				\
+	"sw\t$22,"__str(PT_R22)"($29)\n\t"				\
+	"sw\t$23,"__str(PT_R23)"($29)\n\t"				\
+	"sw\t$30,"__str(PT_R30)"($29)\n\t"				\
+	"j\t" #symbol "\n\t"						\
+	".end\t__" #symbol "\n\t"					\
+	".size\t__" #symbol",. - __" #symbol)
+
+#endif /* CONFIG_32BIT */
+
+#ifdef CONFIG_64BIT
+
+#define save_static_function(symbol)					\
+__asm__(								\
+	".text\n\t"							\
+	".globl\t__" #symbol "\n\t"					\
+	".align\t2\n\t"							\
+	".type\t__" #symbol ", @function\n\t"				\
+	".ent\t__" #symbol ", 0\n__"					\
+	#symbol":\n\t"							\
+	".frame\t$29, 0, $31\n\t"					\
+	"sd\t$16,"__str(PT_R16)"($29)\t\t\t# save_static_function\n\t"	\
+	"sd\t$17,"__str(PT_R17)"($29)\n\t"				\
+	"sd\t$18,"__str(PT_R18)"($29)\n\t"				\
+	"sd\t$19,"__str(PT_R19)"($29)\n\t"				\
+	"sd\t$20,"__str(PT_R20)"($29)\n\t"				\
+	"sd\t$21,"__str(PT_R21)"($29)\n\t"				\
+	"sd\t$22,"__str(PT_R22)"($29)\n\t"				\
+	"sd\t$23,"__str(PT_R23)"($29)\n\t"				\
+	"sd\t$30,"__str(PT_R30)"($29)\n\t"				\
+	"j\t" #symbol "\n\t"						\
+	".end\t__" #symbol "\n\t"					\
+	".size\t__" #symbol",. - __" #symbol)
+
+#endif /* CONFIG_64BIT */
+
+#endif /* _ASM_SIM_H */
diff --git a/arch/mips/include/asm/smp-cps.h b/arch/mips/include/asm/smp-cps.h
new file mode 100644
index 000000000..7e5b9411f
--- /dev/null
+++ b/arch/mips/include/asm/smp-cps.h
@@ -0,0 +1,48 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2013 Imagination Technologies
+ * Author: Paul Burton <paul.burton@mips.com>
+ */
+
+#ifndef __MIPS_ASM_SMP_CPS_H__
+#define __MIPS_ASM_SMP_CPS_H__
+
+#ifndef __ASSEMBLY__
+
+struct vpe_boot_config {
+	unsigned long pc;
+	unsigned long sp;
+	unsigned long gp;
+};
+
+struct core_boot_config {
+	atomic_t vpe_mask;
+	struct vpe_boot_config *vpe_config;
+};
+
+extern struct core_boot_config *mips_cps_core_bootcfg;
+
+extern void mips_cps_core_entry(void);
+extern void mips_cps_core_init(void);
+
+extern void mips_cps_boot_vpes(struct core_boot_config *cfg, unsigned vpe);
+
+extern void mips_cps_pm_save(void);
+extern void mips_cps_pm_restore(void);
+
+#ifdef CONFIG_MIPS_CPS
+
+extern bool mips_cps_smp_in_use(void);
+
+#else /* !CONFIG_MIPS_CPS */
+
+static inline bool mips_cps_smp_in_use(void) { return false; }
+
+#endif /* !CONFIG_MIPS_CPS */
+
+#else /* __ASSEMBLY__ */
+
+.extern mips_cps_bootcfg;
+
+#endif /* __ASSEMBLY__ */
+#endif /* __MIPS_ASM_SMP_CPS_H__ */
diff --git a/arch/mips/include/asm/smp-ops.h b/arch/mips/include/asm/smp-ops.h
new file mode 100644
index 000000000..864aea803
--- /dev/null
+++ b/arch/mips/include/asm/smp-ops.h
@@ -0,0 +1,124 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General
+ * Public License.  See the file "COPYING" in the main directory of this
+ * archive for more details.
+ *
+ * Copyright (C) 2000 - 2001 by Kanoj Sarcar (kanoj@sgi.com)
+ * Copyright (C) 2000 - 2001 by Silicon Graphics, Inc.
+ * Copyright (C) 2000, 2001, 2002 Ralf Baechle
+ * Copyright (C) 2000, 2001 Broadcom Corporation
+ */
+#ifndef __ASM_SMP_OPS_H
+#define __ASM_SMP_OPS_H
+
+#include <linux/errno.h>
+
+#include <asm/mips-cps.h>
+
+#ifdef CONFIG_SMP
+
+#include <linux/cpumask.h>
+
+struct task_struct;
+
+struct plat_smp_ops {
+	void (*send_ipi_single)(int cpu, unsigned int action);
+	void (*send_ipi_mask)(const struct cpumask *mask, unsigned int action);
+	void (*init_secondary)(void);
+	void (*smp_finish)(void);
+	int (*boot_secondary)(int cpu, struct task_struct *idle);
+	void (*smp_setup)(void);
+	void (*prepare_cpus)(unsigned int max_cpus);
+	void (*prepare_boot_cpu)(void);
+#ifdef CONFIG_HOTPLUG_CPU
+	int (*cpu_disable)(void);
+	void (*cpu_die)(unsigned int cpu);
+#endif
+#ifdef CONFIG_KEXEC
+	void (*kexec_nonboot_cpu)(void);
+#endif
+};
+
+extern void register_smp_ops(const struct plat_smp_ops *ops);
+
+static inline void plat_smp_setup(void)
+{
+	extern const struct plat_smp_ops *mp_ops;	/* private */
+
+	mp_ops->smp_setup();
+}
+
+extern void mips_smp_send_ipi_single(int cpu, unsigned int action);
+extern void mips_smp_send_ipi_mask(const struct cpumask *mask,
+				      unsigned int action);
+
+#else /* !CONFIG_SMP */
+
+struct plat_smp_ops;
+
+static inline void plat_smp_setup(void)
+{
+	/* UP, nothing to do ...  */
+}
+
+static inline void register_smp_ops(const struct plat_smp_ops *ops)
+{
+}
+
+#endif /* !CONFIG_SMP */
+
+static inline int register_up_smp_ops(void)
+{
+#ifdef CONFIG_SMP_UP
+	extern const struct plat_smp_ops up_smp_ops;
+
+	register_smp_ops(&up_smp_ops);
+
+	return 0;
+#else
+	return -ENODEV;
+#endif
+}
+
+static inline int register_cmp_smp_ops(void)
+{
+#ifdef CONFIG_MIPS_CMP
+	extern const struct plat_smp_ops cmp_smp_ops;
+
+	if (!mips_cm_present())
+		return -ENODEV;
+
+	register_smp_ops(&cmp_smp_ops);
+
+	return 0;
+#else
+	return -ENODEV;
+#endif
+}
+
+static inline int register_vsmp_smp_ops(void)
+{
+#ifdef CONFIG_MIPS_MT_SMP
+	extern const struct plat_smp_ops vsmp_smp_ops;
+
+	if (!cpu_has_mipsmt)
+		return -ENODEV;
+
+	register_smp_ops(&vsmp_smp_ops);
+
+	return 0;
+#else
+	return -ENODEV;
+#endif
+}
+
+#ifdef CONFIG_MIPS_CPS
+extern int register_cps_smp_ops(void);
+#else
+static inline int register_cps_smp_ops(void)
+{
+	return -ENODEV;
+}
+#endif
+
+#endif /* __ASM_SMP_OPS_H */
diff --git a/arch/mips/include/asm/smp.h b/arch/mips/include/asm/smp.h
new file mode 100644
index 000000000..5d9ff6100
--- /dev/null
+++ b/arch/mips/include/asm/smp.h
@@ -0,0 +1,138 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General
+ * Public License.  See the file "COPYING" in the main directory of this
+ * archive for more details.
+ *
+ * Copyright (C) 2000 - 2001 by Kanoj Sarcar (kanoj@sgi.com)
+ * Copyright (C) 2000 - 2001 by Silicon Graphics, Inc.
+ * Copyright (C) 2000, 2001, 2002 Ralf Baechle
+ * Copyright (C) 2000, 2001 Broadcom Corporation
+ */
+#ifndef __ASM_SMP_H
+#define __ASM_SMP_H
+
+#include <linux/bitops.h>
+#include <linux/linkage.h>
+#include <linux/smp.h>
+#include <linux/threads.h>
+#include <linux/cpumask.h>
+
+#include <linux/atomic.h>
+#include <asm/smp-ops.h>
+
+extern int smp_num_siblings;
+extern cpumask_t cpu_sibling_map[];
+extern cpumask_t cpu_core_map[];
+extern cpumask_t cpu_foreign_map[];
+
+static inline int raw_smp_processor_id(void)
+{
+#if defined(__VDSO__)
+	extern int vdso_smp_processor_id(void)
+		__compiletime_error("VDSO should not call smp_processor_id()");
+	return vdso_smp_processor_id();
+#else
+	return current_thread_info()->cpu;
+#endif
+}
+#define raw_smp_processor_id raw_smp_processor_id
+
+/* Map from cpu id to sequential logical cpu number.  This will only
+   not be idempotent when cpus failed to come on-line.	*/
+extern int __cpu_number_map[CONFIG_MIPS_NR_CPU_NR_MAP];
+#define cpu_number_map(cpu)  __cpu_number_map[cpu]
+
+/* The reverse map from sequential logical cpu number to cpu id.  */
+extern int __cpu_logical_map[NR_CPUS];
+#define cpu_logical_map(cpu)  __cpu_logical_map[cpu]
+
+#define NO_PROC_ID	(-1)
+
+#define SMP_RESCHEDULE_YOURSELF 0x1	/* XXX braindead */
+#define SMP_CALL_FUNCTION	0x2
+/* Octeon - Tell another core to flush its icache */
+#define SMP_ICACHE_FLUSH	0x4
+#define SMP_ASK_C0COUNT		0x8
+
+/* Mask of CPUs which are currently definitely operating coherently */
+extern cpumask_t cpu_coherent_mask;
+
+extern asmlinkage void smp_bootstrap(void);
+
+extern void calculate_cpu_foreign_map(void);
+
+/*
+ * this function sends a 'reschedule' IPI to another CPU.
+ * it goes straight through and wastes no time serializing
+ * anything. Worst case is that we lose a reschedule ...
+ */
+static inline void smp_send_reschedule(int cpu)
+{
+	extern const struct plat_smp_ops *mp_ops;	/* private */
+
+	mp_ops->send_ipi_single(cpu, SMP_RESCHEDULE_YOURSELF);
+}
+
+#ifdef CONFIG_HOTPLUG_CPU
+static inline int __cpu_disable(void)
+{
+	extern const struct plat_smp_ops *mp_ops;	/* private */
+
+	return mp_ops->cpu_disable();
+}
+
+static inline void __cpu_die(unsigned int cpu)
+{
+	extern const struct plat_smp_ops *mp_ops;	/* private */
+
+	mp_ops->cpu_die(cpu);
+}
+
+extern void play_dead(void);
+#endif
+
+#ifdef CONFIG_KEXEC
+static inline void kexec_nonboot_cpu(void)
+{
+	extern const struct plat_smp_ops *mp_ops;	/* private */
+
+	return mp_ops->kexec_nonboot_cpu();
+}
+
+static inline void *kexec_nonboot_cpu_func(void)
+{
+	extern const struct plat_smp_ops *mp_ops;	/* private */
+
+	return mp_ops->kexec_nonboot_cpu;
+}
+#endif
+
+/*
+ * This function will set up the necessary IPIs for Linux to communicate
+ * with the CPUs in mask.
+ * Return 0 on success.
+ */
+int mips_smp_ipi_allocate(const struct cpumask *mask);
+
+/*
+ * This function will free up IPIs allocated with mips_smp_ipi_allocate to the
+ * CPUs in mask, which must be a subset of the IPIs that have been configured.
+ * Return 0 on success.
+ */
+int mips_smp_ipi_free(const struct cpumask *mask);
+
+static inline void arch_send_call_function_single_ipi(int cpu)
+{
+	extern const struct plat_smp_ops *mp_ops;	/* private */
+
+	mp_ops->send_ipi_single(cpu, SMP_CALL_FUNCTION);
+}
+
+static inline void arch_send_call_function_ipi_mask(const struct cpumask *mask)
+{
+	extern const struct plat_smp_ops *mp_ops;	/* private */
+
+	mp_ops->send_ipi_mask(mask, SMP_CALL_FUNCTION);
+}
+
+#endif /* __ASM_SMP_H */
diff --git a/arch/mips/include/asm/sn/addrs.h b/arch/mips/include/asm/sn/addrs.h
new file mode 100644
index 000000000..837d23e24
--- /dev/null
+++ b/arch/mips/include/asm/sn/addrs.h
@@ -0,0 +1,377 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1992 - 1997, 1999, 2000 Silicon Graphics, Inc.
+ * Copyright (C) 1999, 2000 by Ralf Baechle
+ */
+#ifndef _ASM_SN_ADDRS_H
+#define _ASM_SN_ADDRS_H
+
+
+#ifndef __ASSEMBLY__
+#include <linux/smp.h>
+#include <linux/types.h>
+#endif /* !__ASSEMBLY__ */
+
+#include <asm/addrspace.h>
+#include <asm/sn/kldir.h>
+
+#if defined(CONFIG_SGI_IP27)
+#include <asm/sn/sn0/addrs.h>
+#elif defined(CONFIG_SGI_IP35)
+#include <asm/sn/sn1/addrs.h>
+#endif
+
+
+#ifndef __ASSEMBLY__
+
+#define UINT64_CAST		(unsigned long)
+
+#else /* __ASSEMBLY__ */
+
+#define UINT64_CAST
+
+#endif /* __ASSEMBLY__ */
+
+
+#define NASID_GET_META(_n)	((_n) >> NASID_LOCAL_BITS)
+#ifdef CONFIG_SGI_IP27
+#define NASID_GET_LOCAL(_n)	((_n) & 0xf)
+#endif
+#define NASID_MAKE(_m, _l)	(((_m) << NASID_LOCAL_BITS) | (_l))
+
+#define NODE_ADDRSPACE_MASK	(NODE_ADDRSPACE_SIZE - 1)
+#define TO_NODE_ADDRSPACE(_pa)	(UINT64_CAST (_pa) & NODE_ADDRSPACE_MASK)
+
+#define CHANGE_ADDR_NASID(_pa, _nasid)	\
+		((UINT64_CAST(_pa) & ~NASID_MASK) | \
+		 (UINT64_CAST(_nasid) <<  NASID_SHFT))
+
+
+/*
+ * The following macros are used to index to the beginning of a specific
+ * node's address space.
+ */
+
+#define NODE_OFFSET(_n)		(UINT64_CAST (_n) << NODE_SIZE_BITS)
+
+#define NODE_CAC_BASE(_n)	(CAC_BASE   + NODE_OFFSET(_n))
+#define NODE_HSPEC_BASE(_n)	(HSPEC_BASE + NODE_OFFSET(_n))
+#define NODE_IO_BASE(_n)	(IO_BASE    + NODE_OFFSET(_n))
+#define NODE_MSPEC_BASE(_n)	(MSPEC_BASE + NODE_OFFSET(_n))
+#define NODE_UNCAC_BASE(_n)	(UNCAC_BASE + NODE_OFFSET(_n))
+
+#define TO_NODE(_n, _x)		(NODE_OFFSET(_n)     | ((_x)		   ))
+#define TO_NODE_CAC(_n, _x)	(NODE_CAC_BASE(_n)   | ((_x) & TO_PHYS_MASK))
+#define TO_NODE_UNCAC(_n, _x)	(NODE_UNCAC_BASE(_n) | ((_x) & TO_PHYS_MASK))
+#define TO_NODE_MSPEC(_n, _x)	(NODE_MSPEC_BASE(_n) | ((_x) & TO_PHYS_MASK))
+#define TO_NODE_HSPEC(_n, _x)	(NODE_HSPEC_BASE(_n) | ((_x) & TO_PHYS_MASK))
+
+
+#define RAW_NODE_SWIN_BASE(nasid, widget)				\
+	(NODE_IO_BASE(nasid) + (UINT64_CAST(widget) << SWIN_SIZE_BITS))
+
+#define WIDGETID_GET(addr)	((unsigned char)((addr >> SWIN_SIZE_BITS) & 0xff))
+
+/*
+ * The following definitions pertain to the IO special address
+ * space.  They define the location of the big and little windows
+ * of any given node.
+ */
+
+#define SWIN_SIZE_BITS		24
+#define SWIN_SIZE		(UINT64_CAST 1 << 24)
+#define SWIN_SIZEMASK		(SWIN_SIZE - 1)
+#define SWIN_WIDGET_MASK	0xF
+
+/*
+ * Convert smallwindow address to xtalk address.
+ *
+ * 'addr' can be physical or virtual address, but will be converted
+ * to Xtalk address in the range 0 -> SWINZ_SIZEMASK
+ */
+#define SWIN_WIDGETADDR(addr)	((addr) & SWIN_SIZEMASK)
+#define SWIN_WIDGETNUM(addr)	(((addr)  >> SWIN_SIZE_BITS) & SWIN_WIDGET_MASK)
+/*
+ * Verify if addr belongs to small window address on node with "nasid"
+ *
+ *
+ * NOTE: "addr" is expected to be XKPHYS address, and NOT physical
+ * address
+ *
+ *
+ */
+#define NODE_SWIN_ADDR(nasid, addr)	\
+		(((addr) >= NODE_SWIN_BASE(nasid, 0))  && \
+		 ((addr) <  (NODE_SWIN_BASE(nasid, HUB_NUM_WIDGET) + SWIN_SIZE)\
+		 ))
+
+/*
+ * The following define the major position-independent aliases used
+ * in SN.
+ *	UALIAS -- 256MB in size, reads in the UALIAS result in
+ *			uncached references to the memory of the reader's node.
+ *	CPU_UALIAS -- 128kb in size, the bottom part of UALIAS is flipped
+ *			depending on which CPU does the access to provide
+ *			all CPUs with unique uncached memory at low addresses.
+ *	LBOOT  -- 256MB in size, reads in the LBOOT area result in
+ *			uncached references to the local hub's boot prom and
+ *			other directory-bus connected devices.
+ *	IALIAS -- 8MB in size, reads in the IALIAS result in uncached
+ *			references to the local hub's registers.
+ */
+
+#define UALIAS_BASE		HSPEC_BASE
+#define UALIAS_SIZE		0x10000000	/* 256 Megabytes */
+#define UALIAS_LIMIT		(UALIAS_BASE + UALIAS_SIZE)
+
+/*
+ * The bottom of ualias space is flipped depending on whether you're
+ * processor 0 or 1 within a node.
+ */
+#ifdef CONFIG_SGI_IP27
+#define UALIAS_FLIP_BASE	UALIAS_BASE
+#define UALIAS_FLIP_SIZE	0x20000
+#define UALIAS_FLIP_BIT		0x10000
+#define UALIAS_FLIP_ADDR(_x)	(cputoslice(smp_processor_id()) ? \
+				 (_x) ^ UALIAS_FLIP_BIT : (_x))
+
+#define LBOOT_BASE		(HSPEC_BASE + 0x10000000)
+#define LBOOT_SIZE		0x10000000
+#define LBOOT_LIMIT		(LBOOT_BASE + LBOOT_SIZE)
+#define LBOOT_STRIDE		0		/* IP27 has only one CPU PROM */
+
+#endif
+
+#define HUB_REGISTER_WIDGET	1
+#define IALIAS_BASE		NODE_SWIN_BASE(0, HUB_REGISTER_WIDGET)
+#define IALIAS_SIZE		0x800000	/* 8 Megabytes */
+#define IS_IALIAS(_a)		(((_a) >= IALIAS_BASE) &&		\
+				 ((_a) < (IALIAS_BASE + IALIAS_SIZE)))
+
+/*
+ * Macro for referring to Hub's RBOOT space
+ */
+
+#ifdef CONFIG_SGI_IP27
+#define RBOOT_SIZE		0x10000000	/* 256 Megabytes */
+#define NODE_RBOOT_BASE(_n)	(NODE_HSPEC_BASE(_n) + 0x30000000)
+#define NODE_RBOOT_LIMIT(_n)	(NODE_RBOOT_BASE(_n) + RBOOT_SIZE)
+
+#endif
+
+/*
+ * Macros for referring the Hub's back door space
+ *
+ *   These macros correctly process addresses in any node's space.
+ *   WARNING: They won't work in assembler.
+ *
+ *   BDDIR_ENTRY_LO returns the address of the low double-word of the dir
+ *		    entry corresponding to a physical (Cac or Uncac) address.
+ *   BDDIR_ENTRY_HI returns the address of the high double-word of the entry.
+ *   BDPRT_ENTRY    returns the address of the double-word protection entry
+ *		    corresponding to the page containing the physical address.
+ *   BDPRT_ENTRY_S  Stores the value into the protection entry.
+ *   BDPRT_ENTRY_L  Load the value from the protection entry.
+ *   BDECC_ENTRY    returns the address of the ECC byte corresponding to a
+ *		    double-word at a specified physical address.
+ *   BDECC_ENTRY_H  returns the address of the two ECC bytes corresponding to a
+ *		    quad-word at a specified physical address.
+ */
+#define NODE_BDOOR_BASE(_n)	(NODE_HSPEC_BASE(_n) + (NODE_ADDRSPACE_SIZE/2))
+
+#define NODE_BDECC_BASE(_n)	(NODE_BDOOR_BASE(_n))
+#define NODE_BDDIR_BASE(_n)	(NODE_BDOOR_BASE(_n) + (NODE_ADDRSPACE_SIZE/4))
+#ifdef CONFIG_SGI_IP27
+#define BDDIR_ENTRY_LO(_pa)	((HSPEC_BASE +				      \
+				  NODE_ADDRSPACE_SIZE * 3 / 4 +		      \
+				  0x200)				    | \
+				 UINT64_CAST(_pa)	 & NASID_MASK	    | \
+				 UINT64_CAST(_pa) >> 2 & BDDIR_UPPER_MASK  | \
+				 UINT64_CAST(_pa) >> 3 & 0x1f << 4)
+
+#define BDDIR_ENTRY_HI(_pa)	((HSPEC_BASE +				      \
+				  NODE_ADDRSPACE_SIZE * 3 / 4 +		      \
+				  0x208)				    | \
+				 UINT64_CAST(_pa)	 & NASID_MASK	    | \
+				 UINT64_CAST(_pa) >> 2 & BDDIR_UPPER_MASK  | \
+				 UINT64_CAST(_pa) >> 3 & 0x1f << 4)
+
+#define BDPRT_ENTRY(_pa, _rgn)	((HSPEC_BASE +				      \
+				  NODE_ADDRSPACE_SIZE * 3 / 4)		    | \
+				 UINT64_CAST(_pa)	 & NASID_MASK	    | \
+				 UINT64_CAST(_pa) >> 2 & BDDIR_UPPER_MASK  | \
+				 (_rgn) << 3)
+#define BDPRT_ENTRY_ADDR(_pa, _rgn) (BDPRT_ENTRY((_pa), (_rgn)))
+#define BDPRT_ENTRY_S(_pa, _rgn, _val) (*(__psunsigned_t *)BDPRT_ENTRY((_pa), (_rgn))=(_val))
+#define BDPRT_ENTRY_L(_pa, _rgn)	(*(__psunsigned_t *)BDPRT_ENTRY((_pa), (_rgn)))
+
+#define BDECC_ENTRY(_pa)	((HSPEC_BASE +				      \
+				  NODE_ADDRSPACE_SIZE / 2)		    | \
+				 UINT64_CAST(_pa)	 & NASID_MASK	    | \
+				 UINT64_CAST(_pa) >> 2 & BDECC_UPPER_MASK  | \
+				 UINT64_CAST(_pa) >> 3 & 3)
+
+/*
+ * Macro to convert a back door directory or protection address into the
+ *   raw physical address of the associated cache line or protection page.
+ */
+#define BDADDR_IS_DIR(_ba)	((UINT64_CAST  (_ba) & 0x200) != 0)
+#define BDADDR_IS_PRT(_ba)	((UINT64_CAST  (_ba) & 0x200) == 0)
+
+#define BDDIR_TO_MEM(_ba)	(UINT64_CAST (_ba) & NASID_MASK		   | \
+				 (UINT64_CAST(_ba) & BDDIR_UPPER_MASK)<<2  | \
+				 (UINT64_CAST(_ba) & 0x1f << 4) << 3)
+
+#define BDPRT_TO_MEM(_ba)	(UINT64_CAST (_ba) & NASID_MASK	    | \
+				 (UINT64_CAST(_ba) & BDDIR_UPPER_MASK)<<2)
+
+#define BDECC_TO_MEM(_ba)	(UINT64_CAST (_ba) & NASID_MASK	    | \
+				 (UINT64_CAST(_ba) & BDECC_UPPER_MASK)<<2  | \
+				 (UINT64_CAST(_ba) & 3) << 3)
+#endif /* CONFIG_SGI_IP27 */
+
+
+/*
+ * The following macros produce the correct base virtual address for
+ * the hub registers.  The LOCAL_HUB_* macros produce the appropriate
+ * address for the local registers.  The REMOTE_HUB_* macro produce
+ * the address for the specified hub's registers.  The intent is
+ * that the appropriate PI, MD, NI, or II register would be substituted
+ * for _x.
+ */
+
+/*
+ * WARNING:
+ *	When certain Hub chip workaround are defined, it's not sufficient
+ *	to dereference the *_HUB_ADDR() macros.	 You should instead use
+ *	HUB_L() and HUB_S() if you must deal with pointers to hub registers.
+ *	Otherwise, the recommended approach is to use *_HUB_L() and *_HUB_S().
+ *	They're always safe.
+ */
+#define LOCAL_HUB_ADDR(_x)	(IALIAS_BASE + (_x))
+#define REMOTE_HUB_ADDR(_n, _x) ((NODE_SWIN_BASE(_n, 1) + 0x800000 + (_x)))
+
+#ifndef __ASSEMBLY__
+
+#define LOCAL_HUB_PTR(_x)	((u64 *)LOCAL_HUB_ADDR((_x)))
+#define REMOTE_HUB_PTR(_n, _x)	((u64 *)REMOTE_HUB_ADDR((_n), (_x)))
+
+#define LOCAL_HUB_L(_r)			__raw_readq(LOCAL_HUB_PTR(_r))
+#define LOCAL_HUB_S(_r, _d)		__raw_writeq((_d), LOCAL_HUB_PTR(_r))
+#define REMOTE_HUB_L(_n, _r)		__raw_readq(REMOTE_HUB_PTR((_n), (_r)))
+#define REMOTE_HUB_S(_n, _r, _d)	__raw_writeq((_d),		\
+						REMOTE_HUB_PTR((_n), (_r)))
+
+#endif /* !__ASSEMBLY__ */
+
+/*
+ * Software structure locations -- permanently fixed
+ *    See diagram in kldir.h
+ */
+
+#define PHYS_RAMBASE		0x0
+#define K0_RAMBASE		PHYS_TO_K0(PHYS_RAMBASE)
+
+#define EX_HANDLER_OFFSET(slice) ((slice) << 16)
+#define EX_HANDLER_ADDR(nasid, slice)					\
+	PHYS_TO_K0(NODE_OFFSET(nasid) | EX_HANDLER_OFFSET(slice))
+#define EX_HANDLER_SIZE		0x0400
+
+#define EX_FRAME_OFFSET(slice)	((slice) << 16 | 0x400)
+#define EX_FRAME_ADDR(nasid, slice)					\
+	PHYS_TO_K0(NODE_OFFSET(nasid) | EX_FRAME_OFFSET(slice))
+#define EX_FRAME_SIZE		0x0c00
+
+#define ARCS_SPB_OFFSET		0x1000
+#define ARCS_SPB_ADDR(nasid)						\
+	PHYS_TO_K0(NODE_OFFSET(nasid) | ARCS_SPB_OFFSET)
+#define ARCS_SPB_SIZE		0x0400
+
+#define KLDIR_OFFSET		0x2000
+#define KLDIR_ADDR(nasid)						\
+	TO_NODE_UNCAC((nasid), KLDIR_OFFSET)
+#define KLDIR_SIZE		0x0400
+
+
+/*
+ * Software structure locations -- indirected through KLDIR
+ *    See diagram in kldir.h
+ *
+ * Important:	All low memory structures must only be accessed
+ *		uncached, except for the symmon stacks.
+ */
+
+#define KLI_LAUNCH		0		/* Dir. entries */
+#define KLI_KLCONFIG		1
+#define KLI_NMI			2
+#define KLI_GDA			3
+#define KLI_FREEMEM		4
+#define KLI_SYMMON_STK		5
+#define KLI_PI_ERROR		6
+#define KLI_KERN_VARS		7
+#define KLI_KERN_XP		8
+#define KLI_KERN_PARTID		9
+
+#ifndef __ASSEMBLY__
+
+#define KLD_BASE(nasid)		((kldir_ent_t *) KLDIR_ADDR(nasid))
+#define KLD_LAUNCH(nasid)	(KLD_BASE(nasid) + KLI_LAUNCH)
+#define KLD_NMI(nasid)		(KLD_BASE(nasid) + KLI_NMI)
+#define KLD_KLCONFIG(nasid)	(KLD_BASE(nasid) + KLI_KLCONFIG)
+#define KLD_PI_ERROR(nasid)	(KLD_BASE(nasid) + KLI_PI_ERROR)
+#define KLD_GDA(nasid)		(KLD_BASE(nasid) + KLI_GDA)
+#define KLD_SYMMON_STK(nasid)	(KLD_BASE(nasid) + KLI_SYMMON_STK)
+#define KLD_FREEMEM(nasid)	(KLD_BASE(nasid) + KLI_FREEMEM)
+#define KLD_KERN_VARS(nasid)	(KLD_BASE(nasid) + KLI_KERN_VARS)
+#define KLD_KERN_XP(nasid)	(KLD_BASE(nasid) + KLI_KERN_XP)
+#define KLD_KERN_PARTID(nasid)	(KLD_BASE(nasid) + KLI_KERN_PARTID)
+
+#define LAUNCH_OFFSET(nasid, slice)					\
+	(KLD_LAUNCH(nasid)->offset +					\
+	 KLD_LAUNCH(nasid)->stride * (slice))
+#define LAUNCH_ADDR(nasid, slice)					\
+	TO_NODE_UNCAC((nasid), LAUNCH_OFFSET(nasid, slice))
+#define LAUNCH_SIZE(nasid)	KLD_LAUNCH(nasid)->size
+
+#define SN_NMI_OFFSET(nasid, slice)					\
+	(KLD_NMI(nasid)->offset +					\
+	 KLD_NMI(nasid)->stride * (slice))
+#define NMI_ADDR(nasid, slice)						\
+	TO_NODE_UNCAC((nasid), SN_NMI_OFFSET(nasid, slice))
+#define NMI_SIZE(nasid) KLD_NMI(nasid)->size
+
+#define KLCONFIG_OFFSET(nasid)	KLD_KLCONFIG(nasid)->offset
+#define KLCONFIG_ADDR(nasid)						\
+	TO_NODE_UNCAC((nasid), KLCONFIG_OFFSET(nasid))
+#define KLCONFIG_SIZE(nasid)	KLD_KLCONFIG(nasid)->size
+
+#define GDA_ADDR(nasid)		KLD_GDA(nasid)->pointer
+#define GDA_SIZE(nasid)		KLD_GDA(nasid)->size
+
+#define SYMMON_STK_OFFSET(nasid, slice)					\
+	(KLD_SYMMON_STK(nasid)->offset +				\
+	 KLD_SYMMON_STK(nasid)->stride * (slice))
+#define SYMMON_STK_STRIDE(nasid)	KLD_SYMMON_STK(nasid)->stride
+
+#define SYMMON_STK_ADDR(nasid, slice)					\
+	TO_NODE_CAC((nasid), SYMMON_STK_OFFSET(nasid, slice))
+
+#define SYMMON_STK_SIZE(nasid)	KLD_SYMMON_STK(nasid)->stride
+
+#define SYMMON_STK_END(nasid)	(SYMMON_STK_ADDR(nasid, 0) + KLD_SYMMON_STK(nasid)->size)
+
+#define NODE_OFFSET_TO_K0(_nasid, _off)					\
+	PHYS_TO_K0((NODE_OFFSET(_nasid) + (_off)) | CAC_BASE)
+#define NODE_OFFSET_TO_K1(_nasid, _off)					\
+	TO_UNCAC((NODE_OFFSET(_nasid) + (_off)) | UNCAC_BASE)
+
+#define KERN_VARS_ADDR(nasid)	KLD_KERN_VARS(nasid)->pointer
+#define KERN_VARS_SIZE(nasid)	KLD_KERN_VARS(nasid)->size
+
+#endif /* !__ASSEMBLY__ */
+
+
+#endif /* _ASM_SN_ADDRS_H */
diff --git a/arch/mips/include/asm/sn/agent.h b/arch/mips/include/asm/sn/agent.h
new file mode 100644
index 000000000..7e9b32717
--- /dev/null
+++ b/arch/mips/include/asm/sn/agent.h
@@ -0,0 +1,45 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * This file has definitions for the hub and snac interfaces.
+ *
+ * Copyright (C) 1992 - 1997, 1999, 2000 Silcon Graphics, Inc.
+ * Copyright (C) 1999, 2000 Ralf Baechle (ralf@gnu.org)
+ */
+#ifndef _ASM_SGI_SN_AGENT_H
+#define _ASM_SGI_SN_AGENT_H
+
+#include <asm/sn/addrs.h>
+#include <asm/sn/arch.h>
+
+#if defined(CONFIG_SGI_IP27)
+#include <asm/sn/sn0/hub.h>
+#elif defined(CONFIG_SGI_IP35)
+#include <asm/sn/sn1/hub.h>
+#endif	/* !CONFIG_SGI_IP27 && !CONFIG_SGI_IP35 */
+
+/*
+ * NIC register macros
+ */
+
+#if defined(CONFIG_SGI_IP27)
+#define HUB_NIC_ADDR(_cpuid)						   \
+	REMOTE_HUB_ADDR(cpu_to_node(_cpuid),				   \
+		MD_MLAN_CTL)
+#endif
+
+#define SET_HUB_NIC(_my_cpuid, _val)					   \
+	(HUB_S(HUB_NIC_ADDR(_my_cpuid), (_val)))
+
+#define SET_MY_HUB_NIC(_v)						   \
+	SET_HUB_NIC(cpuid(), (_v))
+
+#define GET_HUB_NIC(_my_cpuid)						   \
+	(HUB_L(HUB_NIC_ADDR(_my_cpuid)))
+
+#define GET_MY_HUB_NIC()						   \
+	GET_HUB_NIC(cpuid())
+
+#endif /* _ASM_SGI_SN_AGENT_H */
diff --git a/arch/mips/include/asm/sn/arch.h b/arch/mips/include/asm/sn/arch.h
new file mode 100644
index 000000000..9a9682543
--- /dev/null
+++ b/arch/mips/include/asm/sn/arch.h
@@ -0,0 +1,28 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * SGI specific setup.
+ *
+ * Copyright (C) 1995 - 1997, 1999 Silcon Graphics, Inc.
+ * Copyright (C) 1999 Ralf Baechle (ralf@gnu.org)
+ */
+#ifndef _ASM_SN_ARCH_H
+#define _ASM_SN_ARCH_H
+
+#include <linux/types.h>
+#include <asm/sn/types.h>
+#ifdef CONFIG_SGI_IP27
+#include <asm/sn/sn0/arch.h>
+#endif
+
+#define cputonasid(cpu)		(sn_cpu_info[(cpu)].p_nasid)
+#define cputoslice(cpu)		(sn_cpu_info[(cpu)].p_slice)
+
+#define INVALID_NASID		(nasid_t)-1
+#define INVALID_PNODEID		(pnodeid_t)-1
+#define INVALID_MODULE		(moduleid_t)-1
+#define INVALID_PARTID		(partid_t)-1
+
+#endif /* _ASM_SN_ARCH_H */
diff --git a/arch/mips/include/asm/sn/fru.h b/arch/mips/include/asm/sn/fru.h
new file mode 100644
index 000000000..bbb83257c
--- /dev/null
+++ b/arch/mips/include/asm/sn/fru.h
@@ -0,0 +1,44 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Derived from IRIX <sys/SN/SN0/sn0_fru.h>
+ *
+ * Copyright (C) 1992 - 1997, 1999 Silcon Graphics, Inc.
+ * Copyright (C) 1999, 2006 Ralf Baechle (ralf@linux-mips)
+ */
+#ifndef __ASM_SN_FRU_H
+#define __ASM_SN_FRU_H
+
+#define MAX_DIMMS			8	 /* max # of dimm banks */
+#define MAX_PCIDEV			8	 /* max # of pci devices on a pci bus */
+
+typedef unsigned char confidence_t;
+
+typedef struct kf_mem_s {
+	confidence_t km_confidence; /* confidence level that the memory is bad
+				     * is this necessary ?
+				     */
+	confidence_t km_dimm[MAX_DIMMS];
+				    /* confidence level that dimm[i] is bad
+				     *I think this is the right number
+				     */
+
+} kf_mem_t;
+
+typedef struct kf_cpu_s {
+	confidence_t	kc_confidence; /* confidence level that cpu is bad */
+	confidence_t	kc_icache; /* confidence level that instr. cache is bad */
+	confidence_t	kc_dcache; /* confidence level that data   cache is bad */
+	confidence_t	kc_scache; /* confidence level that sec.   cache is bad */
+	confidence_t	kc_sysbus; /* confidence level that sysad/cmd/state bus is bad */
+} kf_cpu_t;
+
+typedef struct kf_pci_bus_s {
+	confidence_t	kpb_belief;	/* confidence level  that the  pci bus is bad */
+	confidence_t	kpb_pcidev_belief[MAX_PCIDEV];
+					/* confidence level that the pci dev is bad */
+} kf_pci_bus_t;
+
+#endif /* __ASM_SN_FRU_H */
diff --git a/arch/mips/include/asm/sn/gda.h b/arch/mips/include/asm/sn/gda.h
new file mode 100644
index 000000000..5b8c96d5b
--- /dev/null
+++ b/arch/mips/include/asm/sn/gda.h
@@ -0,0 +1,103 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Derived from IRIX <sys/SN/gda.h>.
+ *
+ * Copyright (C) 1992 - 1997, 2000 Silicon Graphics, Inc.
+ *
+ * gda.h -- Contains the data structure for the global data area,
+ *	The GDA contains information communicated between the
+ *	PROM, SYMMON, and the kernel.
+ */
+#ifndef _ASM_SN_GDA_H
+#define _ASM_SN_GDA_H
+
+#include <asm/sn/addrs.h>
+
+/*
+ * GDA Version History
+ *
+ * Version #	| Change
+ * -------------+-------------------------------------------------------
+ *	1	| Initial SN0 version
+ *	2	| Prom sets g_partid field to the partition number. 0 IS
+ *		| a valid partition #.
+ */
+
+#define GDA_VERSION	2	/* Current GDA version # */
+
+#define G_MAGICOFF	0
+#define G_VERSIONOFF	4
+#define G_PROMOPOFF	6
+#define G_MASTEROFF	8
+#define G_VDSOFF	12
+#define G_HKDNORMOFF	16
+#define G_HKDUTLBOFF	24
+#define G_HKDXUTLBOFF	32
+#define G_PARTIDOFF	40
+#define G_TABLEOFF	128
+
+#ifndef __ASSEMBLY__
+
+typedef struct gda {
+	u32	g_magic;	/* GDA magic number */
+	u16	g_version;	/* Version of this structure */
+	u16	g_masterid;	/* The NASID:CPUNUM of the master cpu */
+	u32	g_promop;	/* Passes requests from the kernel to prom */
+	u32	g_vds;		/* Store the virtual dipswitches here */
+	void	**g_hooked_norm;/* ptr to pda loc for norm hndlr */
+	void	**g_hooked_utlb;/* ptr to pda loc for utlb hndlr */
+	void	**g_hooked_xtlb;/* ptr to pda loc for xtlb hndlr */
+	int	g_partid;	/* partition id */
+	int	g_symmax;	/* Max symbols in name table. */
+	void	*g_dbstab;	/* Address of idbg symbol table */
+	char	*g_nametab;	/* Address of idbg name table */
+	void	*g_ktext_repmask;
+				/* Pointer to a mask of nodes with copies
+				 * of the kernel. */
+	char	g_padding[56];	/* pad out to 128 bytes */
+	nasid_t g_nasidtable[MAX_NUMNODES]; /* NASID of each node */
+} gda_t;
+
+#define GDA ((gda_t*) GDA_ADDR(get_nasid()))
+
+#endif /* !__ASSEMBLY__ */
+/*
+ * Define:	PART_GDA_VERSION
+ * Purpose:	Define the minimum version of the GDA required, lower
+ *		revisions assume GDA is NOT set up, and read partition
+ *		information from the board info.
+ */
+#define PART_GDA_VERSION	2
+
+/*
+ * The following requests can be sent to the PROM during startup.
+ */
+
+#define PROMOP_MAGIC		0x0ead0000
+#define PROMOP_MAGIC_MASK	0x0fff0000
+
+#define PROMOP_BIST_SHIFT	11
+#define PROMOP_BIST_MASK	(0x3 << 11)
+
+#define PROMOP_REG		PI_ERR_STACK_ADDR_A
+
+#define PROMOP_INVALID		(PROMOP_MAGIC | 0x00)
+#define PROMOP_HALT		(PROMOP_MAGIC | 0x10)
+#define PROMOP_POWERDOWN	(PROMOP_MAGIC | 0x20)
+#define PROMOP_RESTART		(PROMOP_MAGIC | 0x30)
+#define PROMOP_REBOOT		(PROMOP_MAGIC | 0x40)
+#define PROMOP_IMODE		(PROMOP_MAGIC | 0x50)
+
+#define PROMOP_CMD_MASK		0x00f0
+#define PROMOP_OPTIONS_MASK	0xfff0
+
+#define PROMOP_SKIP_DIAGS	0x0100		/* don't bother running diags */
+#define PROMOP_SKIP_MEMINIT	0x0200		/* don't bother initing memory */
+#define PROMOP_SKIP_DEVINIT	0x0400		/* don't bother initing devices */
+#define PROMOP_BIST1		0x0800		/* keep track of which BIST ran */
+#define PROMOP_BIST2		0x1000		/* keep track of which BIST ran */
+
+#endif /* _ASM_SN_GDA_H */
diff --git a/arch/mips/include/asm/sn/intr.h b/arch/mips/include/asm/sn/intr.h
new file mode 100644
index 000000000..3d6954d37
--- /dev/null
+++ b/arch/mips/include/asm/sn/intr.h
@@ -0,0 +1,112 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1992 - 1997 Silicon Graphics, Inc.
+ */
+#ifndef __ASM_SN_INTR_H
+#define __ASM_SN_INTR_H
+
+/*
+ * Macros to manipulate the interrupt register on the calling hub chip.
+ */
+
+#define LOCAL_HUB_SEND_INTR(level)				\
+	LOCAL_HUB_S(PI_INT_PEND_MOD, (0x100 | (level)))
+#define REMOTE_HUB_SEND_INTR(hub, level)			\
+	REMOTE_HUB_S((hub), PI_INT_PEND_MOD, (0x100 | (level)))
+
+/*
+ * When clearing the interrupt, make sure this clear does make it
+ * to the hub. Otherwise we could end up losing interrupts.
+ * We do an uncached load of the int_pend0 register to ensure this.
+ */
+
+#define LOCAL_HUB_CLR_INTR(level)				\
+do {								\
+	LOCAL_HUB_S(PI_INT_PEND_MOD, (level));			\
+	LOCAL_HUB_L(PI_INT_PEND0);				\
+} while (0);
+
+#define REMOTE_HUB_CLR_INTR(hub, level)				\
+do {								\
+	nasid_t	 __hub = (hub);					\
+								\
+	REMOTE_HUB_S(__hub, PI_INT_PEND_MOD, (level));		\
+	REMOTE_HUB_L(__hub, PI_INT_PEND0);			\
+} while (0);
+
+/*
+ * Hard-coded interrupt levels:
+ */
+
+/*
+ *	L0 = SW1
+ *	L1 = SW2
+ *	L2 = INT_PEND0
+ *	L3 = INT_PEND1
+ *	L4 = RTC
+ *	L5 = Profiling Timer
+ *	L6 = Hub Errors
+ *	L7 = Count/Compare (T5 counters)
+ */
+
+
+/*
+ * INT_PEND0 hard-coded bits.
+ */
+
+/*
+ * INT_PEND0 bits determined by hardware:
+ */
+#define RESERVED_INTR		 0	/* What is this bit? */
+#define GFX_INTR_A		 1
+#define GFX_INTR_B		 2
+#define PG_MIG_INTR		 3
+#define UART_INTR		 4
+#define CC_PEND_A		 5
+#define CC_PEND_B		 6
+
+/*
+ * INT_PEND0 used by the kernel for itself ...
+ */
+#define CPU_RESCHED_A_IRQ	 7
+#define CPU_RESCHED_B_IRQ	 8
+#define CPU_CALL_A_IRQ		 9
+#define CPU_CALL_B_IRQ		10
+
+/*
+ * INT_PEND1 hard-coded bits:
+ */
+#define NI_BRDCAST_ERR_A	39
+#define NI_BRDCAST_ERR_B	40
+
+#define LLP_PFAIL_INTR_A	41	/* see ml/SN/SN0/sysctlr.c */
+#define LLP_PFAIL_INTR_B	42
+
+#define TLB_INTR_A		43	/* used for tlb flush random */
+#define TLB_INTR_B		44
+
+#define IP27_INTR_0		45	/* Reserved for PROM use */
+#define IP27_INTR_1		46	/* do not use in Kernel */
+#define IP27_INTR_2		47
+#define IP27_INTR_3		48
+#define IP27_INTR_4		49
+#define IP27_INTR_5		50
+#define IP27_INTR_6		51
+#define IP27_INTR_7		52
+
+#define BRIDGE_ERROR_INTR	53	/* Setup by PROM to catch	*/
+					/* Bridge Errors */
+#define DEBUG_INTR_A		54
+#define DEBUG_INTR_B		55	/* Used by symmon to stop all cpus */
+#define IO_ERROR_INTR		57	/* Setup by PROM */
+#define CLK_ERR_INTR		58
+#define COR_ERR_INTR_A		59
+#define COR_ERR_INTR_B		60
+#define MD_COR_ERR_INTR		61
+#define NI_ERROR_INTR		62
+#define MSC_PANIC_INTR		63
+
+#endif /* __ASM_SN_INTR_H */
diff --git a/arch/mips/include/asm/sn/io.h b/arch/mips/include/asm/sn/io.h
new file mode 100644
index 000000000..211f1e83b
--- /dev/null
+++ b/arch/mips/include/asm/sn/io.h
@@ -0,0 +1,59 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2000, 2003 Ralf Baechle
+ * Copyright (C) 2000 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_SN_IO_H
+#define _ASM_SN_IO_H
+
+#if defined(CONFIG_SGI_IP27)
+#include <asm/sn/sn0/hubio.h>
+#endif
+
+
+#define IIO_ITTE_BASE		0x400160 /* base of translation table entries */
+#define IIO_ITTE(bigwin)	(IIO_ITTE_BASE + 8*(bigwin))
+
+#define IIO_ITTE_OFFSET_BITS	5	/* size of offset field */
+#define IIO_ITTE_OFFSET_MASK	((1<<IIO_ITTE_OFFSET_BITS)-1)
+#define IIO_ITTE_OFFSET_SHIFT	0
+
+#define IIO_ITTE_WIDGET_BITS	4	/* size of widget field */
+#define IIO_ITTE_WIDGET_MASK	((1<<IIO_ITTE_WIDGET_BITS)-1)
+#define IIO_ITTE_WIDGET_SHIFT	8
+
+#define IIO_ITTE_IOSP		1	/* I/O Space bit */
+#define IIO_ITTE_IOSP_MASK	1
+#define IIO_ITTE_IOSP_SHIFT	12
+#define HUB_PIO_MAP_TO_MEM	0
+#define HUB_PIO_MAP_TO_IO	1
+
+#define IIO_ITTE_INVALID_WIDGET 3	/* an invalid widget  */
+
+#define IIO_ITTE_PUT(nasid, bigwin, io_or_mem, widget, addr) \
+	REMOTE_HUB_S((nasid), IIO_ITTE(bigwin), \
+		(((((addr) >> BWIN_SIZE_BITS) & \
+		   IIO_ITTE_OFFSET_MASK) << IIO_ITTE_OFFSET_SHIFT) | \
+		(io_or_mem << IIO_ITTE_IOSP_SHIFT) | \
+		(((widget) & IIO_ITTE_WIDGET_MASK) << IIO_ITTE_WIDGET_SHIFT)))
+
+#define IIO_ITTE_DISABLE(nasid, bigwin) \
+	IIO_ITTE_PUT((nasid), HUB_PIO_MAP_TO_MEM, \
+		     (bigwin), IIO_ITTE_INVALID_WIDGET, 0)
+
+#define IIO_ITTE_GET(nasid, bigwin) REMOTE_HUB_PTR((nasid), IIO_ITTE(bigwin))
+
+/*
+ * Macro which takes the widget number, and returns the
+ * IO PRB address of that widget.
+ * value _x is expected to be a widget number in the range
+ * 0, 8 - 0xF
+ */
+#define IIO_IOPRB(_x)	(IIO_IOPRB_0 + ( ( (_x) < HUB_WIDGET_ID_MIN ? \
+			(_x) : \
+			(_x) - (HUB_WIDGET_ID_MIN-1)) << 3) )
+
+#endif /* _ASM_SN_IO_H */
diff --git a/arch/mips/include/asm/sn/ioc3.h b/arch/mips/include/asm/sn/ioc3.h
new file mode 100644
index 000000000..2c09c17ca
--- /dev/null
+++ b/arch/mips/include/asm/sn/ioc3.h
@@ -0,0 +1,606 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 1999, 2000 Ralf Baechle
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ */
+#ifndef MIPS_SN_IOC3_H
+#define MIPS_SN_IOC3_H
+
+#include <linux/types.h>
+
+/* serial port register map */
+struct ioc3_serialregs {
+	u32	sscr;
+	u32	stpir;
+	u32	stcir;
+	u32	srpir;
+	u32	srcir;
+	u32	srtr;
+	u32	shadow;
+};
+
+/* SUPERIO uart register map */
+struct ioc3_uartregs {
+	u8	iu_lcr;
+	union {
+		u8	iu_iir;	/* read only */
+		u8	iu_fcr;	/* write only */
+	};
+	union {
+		u8	iu_ier;	/* DLAB == 0 */
+		u8	iu_dlm;	/* DLAB == 1 */
+	};
+	union {
+		u8	iu_rbr;	/* read only, DLAB == 0 */
+		u8	iu_thr;	/* write only, DLAB == 0 */
+		u8	iu_dll;	/* DLAB == 1 */
+	};
+	u8	iu_scr;
+	u8	iu_msr;
+	u8	iu_lsr;
+	u8	iu_mcr;
+};
+
+struct ioc3_sioregs {
+	u8	fill[0x141];	/* starts at 0x141 */
+
+	u8	kbdcg;
+	u8	uartc;
+
+	u8	fill0[0x151 - 0x142 - 1];
+
+	u8	pp_dcr;
+	u8	pp_dsr;
+	u8	pp_data;
+
+	u8	fill1[0x159 - 0x153 - 1];
+
+	u8	pp_ecr;
+	u8	pp_cfgb;
+	u8	pp_fifa;
+
+	u8	fill2[0x16a - 0x15b - 1];
+
+	u8	rtcdat;
+	u8	rtcad;
+
+	u8	fill3[0x170 - 0x16b - 1];
+
+	struct ioc3_uartregs	uartb;	/* 0x20170  */
+	struct ioc3_uartregs	uarta;	/* 0x20178  */
+};
+
+struct ioc3_ethregs {
+	u32	emcr;		/* 0x000f0  */
+	u32	eisr;		/* 0x000f4  */
+	u32	eier;		/* 0x000f8  */
+	u32	ercsr;		/* 0x000fc  */
+	u32	erbr_h;		/* 0x00100  */
+	u32	erbr_l;		/* 0x00104  */
+	u32	erbar;		/* 0x00108  */
+	u32	ercir;		/* 0x0010c  */
+	u32	erpir;		/* 0x00110  */
+	u32	ertr;		/* 0x00114  */
+	u32	etcsr;		/* 0x00118  */
+	u32	ersr;		/* 0x0011c  */
+	u32	etcdc;		/* 0x00120  */
+	u32	ebir;		/* 0x00124  */
+	u32	etbr_h;		/* 0x00128  */
+	u32	etbr_l;		/* 0x0012c  */
+	u32	etcir;		/* 0x00130  */
+	u32	etpir;		/* 0x00134  */
+	u32	emar_h;		/* 0x00138  */
+	u32	emar_l;		/* 0x0013c  */
+	u32	ehar_h;		/* 0x00140  */
+	u32	ehar_l;		/* 0x00144  */
+	u32	micr;		/* 0x00148  */
+	u32	midr_r;		/* 0x0014c  */
+	u32	midr_w;		/* 0x00150  */
+};
+
+struct ioc3_serioregs {
+	u32	km_csr;		/* 0x0009c  */
+	u32	k_rd;		/* 0x000a0  */
+	u32	m_rd;		/* 0x000a4  */
+	u32	k_wd;		/* 0x000a8  */
+	u32	m_wd;		/* 0x000ac  */
+};
+
+/* Register layout of IOC3 in configuration space.  */
+struct ioc3 {
+	/* PCI Config Space registers  */
+	u32	pci_id;		/* 0x00000  */
+	u32	pci_scr;	/* 0x00004  */
+	u32	pci_rev;	/* 0x00008  */
+	u32	pci_lat;	/* 0x0000c  */
+	u32	pci_addr;	/* 0x00010  */
+	u32	pci_err_addr_l;	/* 0x00014  */
+	u32	pci_err_addr_h;	/* 0x00018  */
+
+	u32	sio_ir;		/* 0x0001c  */
+	u32	sio_ies;	/* 0x00020  */
+	u32	sio_iec;	/* 0x00024  */
+	u32	sio_cr;		/* 0x00028  */
+	u32	int_out;	/* 0x0002c  */
+	u32	mcr;		/* 0x00030  */
+
+	/* General Purpose I/O registers  */
+	u32	gpcr_s;		/* 0x00034  */
+	u32	gpcr_c;		/* 0x00038  */
+	u32	gpdr;		/* 0x0003c  */
+	u32	gppr[16];	/* 0x00040  */
+
+	/* Parallel Port Registers  */
+	u32	ppbr_h_a;	/* 0x00080  */
+	u32	ppbr_l_a;	/* 0x00084  */
+	u32	ppcr_a;		/* 0x00088  */
+	u32	ppcr;		/* 0x0008c  */
+	u32	ppbr_h_b;	/* 0x00090  */
+	u32	ppbr_l_b;	/* 0x00094  */
+	u32	ppcr_b;		/* 0x00098  */
+
+	/* Keyboard and Mouse Registers	 */
+	struct ioc3_serioregs	serio;
+
+	/* Serial Port Registers  */
+	u32	sbbr_h;		/* 0x000b0  */
+	u32	sbbr_l;		/* 0x000b4  */
+	struct ioc3_serialregs	port_a;
+	struct ioc3_serialregs	port_b;
+
+	/* Ethernet Registers */
+	struct ioc3_ethregs	eth;
+	u32	pad1[(0x20000 - 0x00154) / 4];
+
+	/* SuperIO Registers  XXX */
+	struct ioc3_sioregs	sregs;	/* 0x20000 */
+	u32	pad2[(0x40000 - 0x20180) / 4];
+
+	/* SSRAM Diagnostic Access */
+	u32	ssram[(0x80000 - 0x40000) / 4];
+
+	/* Bytebus device offsets
+	   0x80000 -   Access to the generic devices selected with   DEV0
+	   0x9FFFF     bytebus DEV_SEL_0
+	   0xA0000 -   Access to the generic devices selected with   DEV1
+	   0xBFFFF     bytebus DEV_SEL_1
+	   0xC0000 -   Access to the generic devices selected with   DEV2
+	   0xDFFFF     bytebus DEV_SEL_2
+	   0xE0000 -   Access to the generic devices selected with   DEV3
+	   0xFFFFF     bytebus DEV_SEL_3  */
+};
+
+
+#define PCI_LAT			0xc		/* Latency Timer */
+#define PCI_SCR_DROP_MODE_EN	0x00008000	/* drop pios on parity err */
+#define UARTA_BASE		0x178
+#define UARTB_BASE		0x170
+
+/*
+ * Bytebus device space
+ */
+#define IOC3_BYTEBUS_DEV0	0x80000L
+#define IOC3_BYTEBUS_DEV1	0xa0000L
+#define IOC3_BYTEBUS_DEV2	0xc0000L
+#define IOC3_BYTEBUS_DEV3	0xe0000L
+
+/*
+ * Ethernet RX Buffer
+ */
+struct ioc3_erxbuf {
+	u32	w0;			/* first word (valid,bcnt,cksum) */
+	u32	err;			/* second word various errors */
+	/* next comes n bytes of padding */
+	/* then the received ethernet frame itself */
+};
+
+#define ERXBUF_IPCKSUM_MASK	0x0000ffff
+#define ERXBUF_BYTECNT_MASK	0x07ff0000
+#define ERXBUF_BYTECNT_SHIFT	16
+#define ERXBUF_V		0x80000000
+
+#define ERXBUF_CRCERR		0x00000001	/* aka RSV15 */
+#define ERXBUF_FRAMERR		0x00000002	/* aka RSV14 */
+#define ERXBUF_CODERR		0x00000004	/* aka RSV13 */
+#define ERXBUF_INVPREAMB	0x00000008	/* aka RSV18 */
+#define ERXBUF_LOLEN		0x00007000	/* aka RSV2_0 */
+#define ERXBUF_HILEN		0x03ff0000	/* aka RSV12_3 */
+#define ERXBUF_MULTICAST	0x04000000	/* aka RSV16 */
+#define ERXBUF_BROADCAST	0x08000000	/* aka RSV17 */
+#define ERXBUF_LONGEVENT	0x10000000	/* aka RSV19 */
+#define ERXBUF_BADPKT		0x20000000	/* aka RSV20 */
+#define ERXBUF_GOODPKT		0x40000000	/* aka RSV21 */
+#define ERXBUF_CARRIER		0x80000000	/* aka RSV22 */
+
+/*
+ * Ethernet TX Descriptor
+ */
+#define ETXD_DATALEN	104
+struct ioc3_etxd {
+	u32	cmd;				/* command field */
+	u32	bufcnt;				/* buffer counts field */
+	u64	p1;				/* buffer pointer 1 */
+	u64	p2;				/* buffer pointer 2 */
+	u8	data[ETXD_DATALEN];		/* opt. tx data */
+};
+
+#define ETXD_BYTECNT_MASK	0x000007ff	/* total byte count */
+#define ETXD_INTWHENDONE	0x00001000	/* intr when done */
+#define ETXD_D0V		0x00010000	/* data 0 valid */
+#define ETXD_B1V		0x00020000	/* buf 1 valid */
+#define ETXD_B2V		0x00040000	/* buf 2 valid */
+#define ETXD_DOCHECKSUM		0x00080000	/* insert ip cksum */
+#define ETXD_CHKOFF_MASK	0x07f00000	/* cksum byte offset */
+#define ETXD_CHKOFF_SHIFT	20
+
+#define ETXD_D0CNT_MASK		0x0000007f
+#define ETXD_B1CNT_MASK		0x0007ff00
+#define ETXD_B1CNT_SHIFT	8
+#define ETXD_B2CNT_MASK		0x7ff00000
+#define ETXD_B2CNT_SHIFT	20
+
+/* ------------------------------------------------------------------------- */
+
+/* Superio Registers (PIO Access) */
+#define IOC3_SIO_BASE		0x20000
+#define IOC3_SIO_UARTC		(IOC3_SIO_BASE+0x141)	/* UART Config */
+#define IOC3_SIO_KBDCG		(IOC3_SIO_BASE+0x142)	/* KBD Config */
+#define IOC3_SIO_PP_BASE	(IOC3_SIO_BASE+PP_BASE)	/* Parallel Port */
+#define IOC3_SIO_RTC_BASE	(IOC3_SIO_BASE+0x168)	/* Real Time Clock */
+#define IOC3_SIO_UB_BASE	(IOC3_SIO_BASE+UARTB_BASE)	/* UART B */
+#define IOC3_SIO_UA_BASE	(IOC3_SIO_BASE+UARTA_BASE)	/* UART A */
+
+/* SSRAM Diagnostic Access */
+#define IOC3_SSRAM	IOC3_RAM_OFF	/* base of SSRAM diagnostic access */
+#define IOC3_SSRAM_LEN	0x40000	/* 256kb (addrspc sz, may not be populated) */
+#define IOC3_SSRAM_DM	0x0000ffff	/* data mask */
+#define IOC3_SSRAM_PM	0x00010000	/* parity mask */
+
+/* bitmasks for PCI_SCR */
+#define PCI_SCR_PAR_RESP_EN	0x00000040	/* enb PCI parity checking */
+#define PCI_SCR_SERR_EN		0x00000100	/* enable the SERR# driver */
+#define PCI_SCR_DROP_MODE_EN	0x00008000	/* drop pios on parity err */
+#define PCI_SCR_RX_SERR		(0x1 << 16)
+#define PCI_SCR_DROP_MODE	(0x1 << 17)
+#define PCI_SCR_SIG_PAR_ERR	(0x1 << 24)
+#define PCI_SCR_SIG_TAR_ABRT	(0x1 << 27)
+#define PCI_SCR_RX_TAR_ABRT	(0x1 << 28)
+#define PCI_SCR_SIG_MST_ABRT	(0x1 << 29)
+#define PCI_SCR_SIG_SERR	(0x1 << 30)
+#define PCI_SCR_PAR_ERR		(0x1 << 31)
+
+/* bitmasks for IOC3_KM_CSR */
+#define KM_CSR_K_WRT_PEND 0x00000001	/* kbd port xmitting or resetting */
+#define KM_CSR_M_WRT_PEND 0x00000002	/* mouse port xmitting or resetting */
+#define KM_CSR_K_LCB	  0x00000004	/* Line Cntrl Bit for last KBD write */
+#define KM_CSR_M_LCB	  0x00000008	/* same for mouse */
+#define KM_CSR_K_DATA	  0x00000010	/* state of kbd data line */
+#define KM_CSR_K_CLK	  0x00000020	/* state of kbd clock line */
+#define KM_CSR_K_PULL_DATA 0x00000040	/* pull kbd data line low */
+#define KM_CSR_K_PULL_CLK 0x00000080	/* pull kbd clock line low */
+#define KM_CSR_M_DATA	  0x00000100	/* state of ms data line */
+#define KM_CSR_M_CLK	  0x00000200	/* state of ms clock line */
+#define KM_CSR_M_PULL_DATA 0x00000400	/* pull ms data line low */
+#define KM_CSR_M_PULL_CLK 0x00000800	/* pull ms clock line low */
+#define KM_CSR_EMM_MODE	  0x00001000	/* emulation mode */
+#define KM_CSR_SIM_MODE	  0x00002000	/* clock X8 */
+#define KM_CSR_K_SM_IDLE  0x00004000	/* Keyboard is idle */
+#define KM_CSR_M_SM_IDLE  0x00008000	/* Mouse is idle */
+#define KM_CSR_K_TO	  0x00010000	/* Keyboard trying to send/receive */
+#define KM_CSR_M_TO	  0x00020000	/* Mouse trying to send/receive */
+#define KM_CSR_K_TO_EN	  0x00040000	/* KM_CSR_K_TO + KM_CSR_K_TO_EN = cause
+					   SIO_IR to assert */
+#define KM_CSR_M_TO_EN	  0x00080000	/* KM_CSR_M_TO + KM_CSR_M_TO_EN = cause
+					   SIO_IR to assert */
+#define KM_CSR_K_CLAMP_1  0x00100000	/* Pull K_CLK low aft recv 1 char */
+#define KM_CSR_M_CLAMP_1  0x00200000	/* Pull M_CLK low aft recv 1 char */
+#define KM_CSR_K_CLAMP_3  0x00400000	/* Pull K_CLK low aft recv 3 chars */
+#define KM_CSR_M_CLAMP_3  0x00800000	/* Pull M_CLK low aft recv 3 chars */
+
+/* bitmasks for IOC3_K_RD and IOC3_M_RD */
+#define KM_RD_DATA_2	0x000000ff	/* 3rd char recvd since last read */
+#define KM_RD_DATA_2_SHIFT 0
+#define KM_RD_DATA_1	0x0000ff00	/* 2nd char recvd since last read */
+#define KM_RD_DATA_1_SHIFT 8
+#define KM_RD_DATA_0	0x00ff0000	/* 1st char recvd since last read */
+#define KM_RD_DATA_0_SHIFT 16
+#define KM_RD_FRAME_ERR_2 0x01000000	/*  framing or parity error in byte 2 */
+#define KM_RD_FRAME_ERR_1 0x02000000	/* same for byte 1 */
+#define KM_RD_FRAME_ERR_0 0x04000000	/* same for byte 0 */
+
+#define KM_RD_KBD_MSE	0x08000000	/* 0 if from kbd, 1 if from mouse */
+#define KM_RD_OFLO	0x10000000	/* 4th char recvd before this read */
+#define KM_RD_VALID_2	0x20000000	/* DATA_2 valid */
+#define KM_RD_VALID_1	0x40000000	/* DATA_1 valid */
+#define KM_RD_VALID_0	0x80000000	/* DATA_0 valid */
+#define KM_RD_VALID_ALL (KM_RD_VALID_0|KM_RD_VALID_1|KM_RD_VALID_2)
+
+/* bitmasks for IOC3_K_WD & IOC3_M_WD */
+#define KM_WD_WRT_DATA	0x000000ff	/* write to keyboard/mouse port */
+#define KM_WD_WRT_DATA_SHIFT 0
+
+/* bitmasks for serial RX status byte */
+#define RXSB_OVERRUN	0x01	/* char(s) lost */
+#define RXSB_PAR_ERR	0x02	/* parity error */
+#define RXSB_FRAME_ERR	0x04	/* framing error */
+#define RXSB_BREAK	0x08	/* break character */
+#define RXSB_CTS	0x10	/* state of CTS */
+#define RXSB_DCD	0x20	/* state of DCD */
+#define RXSB_MODEM_VALID 0x40	/* DCD, CTS and OVERRUN are valid */
+#define RXSB_DATA_VALID 0x80	/* data byte, FRAME_ERR PAR_ERR & BREAK valid */
+
+/* bitmasks for serial TX control byte */
+#define TXCB_INT_WHEN_DONE 0x20 /* interrupt after this byte is sent */
+#define TXCB_INVALID	0x00	/* byte is invalid */
+#define TXCB_VALID	0x40	/* byte is valid */
+#define TXCB_MCR	0x80	/* data<7:0> to modem control register */
+#define TXCB_DELAY	0xc0	/* delay data<7:0> mSec */
+
+/* bitmasks for IOC3_SBBR_L */
+#define SBBR_L_SIZE	0x00000001	/* 0 == 1KB rings, 1 == 4KB rings */
+#define SBBR_L_BASE	0xfffff000	/* lower serial ring base addr */
+
+/* bitmasks for IOC3_SSCR_<A:B> */
+#define SSCR_RX_THRESHOLD 0x000001ff	/* hiwater mark */
+#define SSCR_TX_TIMER_BUSY 0x00010000	/* TX timer in progress */
+#define SSCR_HFC_EN	0x00020000	/* hardware flow control enabled */
+#define SSCR_RX_RING_DCD 0x00040000	/* post RX record on delta-DCD */
+#define SSCR_RX_RING_CTS 0x00080000	/* post RX record on delta-CTS */
+#define SSCR_HIGH_SPD	0x00100000	/* 4X speed */
+#define SSCR_DIAG	0x00200000	/* bypass clock divider for sim */
+#define SSCR_RX_DRAIN	0x08000000	/* drain RX buffer to memory */
+#define SSCR_DMA_EN	0x10000000	/* enable ring buffer DMA */
+#define SSCR_DMA_PAUSE	0x20000000	/* pause DMA */
+#define SSCR_PAUSE_STATE 0x40000000	/* sets when PAUSE takes effect */
+#define SSCR_RESET	0x80000000	/* reset DMA channels */
+
+/* all producer/consumer pointers are the same bitfield */
+#define PROD_CONS_PTR_4K 0x00000ff8	/* for 4K buffers */
+#define PROD_CONS_PTR_1K 0x000003f8	/* for 1K buffers */
+#define PROD_CONS_PTR_OFF 3
+
+/* bitmasks for IOC3_SRCIR_<A:B> */
+#define SRCIR_ARM	0x80000000	/* arm RX timer */
+
+/* bitmasks for IOC3_SRPIR_<A:B> */
+#define SRPIR_BYTE_CNT	0x07000000	/* bytes in packer */
+#define SRPIR_BYTE_CNT_SHIFT 24
+
+/* bitmasks for IOC3_STCIR_<A:B> */
+#define STCIR_BYTE_CNT	0x0f000000	/* bytes in unpacker */
+#define STCIR_BYTE_CNT_SHIFT 24
+
+/* bitmasks for IOC3_SHADOW_<A:B> */
+#define SHADOW_DR	0x00000001	/* data ready */
+#define SHADOW_OE	0x00000002	/* overrun error */
+#define SHADOW_PE	0x00000004	/* parity error */
+#define SHADOW_FE	0x00000008	/* framing error */
+#define SHADOW_BI	0x00000010	/* break interrupt */
+#define SHADOW_THRE	0x00000020	/* transmit holding register empty */
+#define SHADOW_TEMT	0x00000040	/* transmit shift register empty */
+#define SHADOW_RFCE	0x00000080	/* char in RX fifo has an error */
+#define SHADOW_DCTS	0x00010000	/* delta clear to send */
+#define SHADOW_DDCD	0x00080000	/* delta data carrier detect */
+#define SHADOW_CTS	0x00100000	/* clear to send */
+#define SHADOW_DCD	0x00800000	/* data carrier detect */
+#define SHADOW_DTR	0x01000000	/* data terminal ready */
+#define SHADOW_RTS	0x02000000	/* request to send */
+#define SHADOW_OUT1	0x04000000	/* 16550 OUT1 bit */
+#define SHADOW_OUT2	0x08000000	/* 16550 OUT2 bit */
+#define SHADOW_LOOP	0x10000000	/* loopback enabled */
+
+/* bitmasks for IOC3_SRTR_<A:B> */
+#define SRTR_CNT	0x00000fff	/* reload value for RX timer */
+#define SRTR_CNT_VAL	0x0fff0000	/* current value of RX timer */
+#define SRTR_CNT_VAL_SHIFT 16
+#define SRTR_HZ		16000	/* SRTR clock frequency */
+
+/* bitmasks for IOC3_SIO_IR, IOC3_SIO_IEC and IOC3_SIO_IES  */
+#define SIO_IR_SA_TX_MT		0x00000001	/* Serial port A TX empty */
+#define SIO_IR_SA_RX_FULL	0x00000002	/* port A RX buf full */
+#define SIO_IR_SA_RX_HIGH	0x00000004	/* port A RX hiwat */
+#define SIO_IR_SA_RX_TIMER	0x00000008	/* port A RX timeout */
+#define SIO_IR_SA_DELTA_DCD	0x00000010	/* port A delta DCD */
+#define SIO_IR_SA_DELTA_CTS	0x00000020	/* port A delta CTS */
+#define SIO_IR_SA_INT		0x00000040	/* port A pass-thru intr */
+#define SIO_IR_SA_TX_EXPLICIT	0x00000080	/* port A explicit TX thru */
+#define SIO_IR_SA_MEMERR	0x00000100	/* port A PCI error */
+#define SIO_IR_SB_TX_MT		0x00000200	/* */
+#define SIO_IR_SB_RX_FULL	0x00000400	/* */
+#define SIO_IR_SB_RX_HIGH	0x00000800	/* */
+#define SIO_IR_SB_RX_TIMER	0x00001000	/* */
+#define SIO_IR_SB_DELTA_DCD	0x00002000	/* */
+#define SIO_IR_SB_DELTA_CTS	0x00004000	/* */
+#define SIO_IR_SB_INT		0x00008000	/* */
+#define SIO_IR_SB_TX_EXPLICIT	0x00010000	/* */
+#define SIO_IR_SB_MEMERR	0x00020000	/* */
+#define SIO_IR_PP_INT		0x00040000	/* P port pass-thru intr */
+#define SIO_IR_PP_INTA		0x00080000	/* PP context A thru */
+#define SIO_IR_PP_INTB		0x00100000	/* PP context B thru */
+#define SIO_IR_PP_MEMERR	0x00200000	/* PP PCI error */
+#define SIO_IR_KBD_INT		0x00400000	/* kbd/mouse intr */
+#define SIO_IR_RT_INT		0x08000000	/* RT output pulse */
+#define SIO_IR_GEN_INT1		0x10000000	/* RT input pulse */
+#define SIO_IR_GEN_INT_SHIFT	28
+
+/* per device interrupt masks */
+#define SIO_IR_SA		(SIO_IR_SA_TX_MT | SIO_IR_SA_RX_FULL | \
+				 SIO_IR_SA_RX_HIGH | SIO_IR_SA_RX_TIMER | \
+				 SIO_IR_SA_DELTA_DCD | SIO_IR_SA_DELTA_CTS | \
+				 SIO_IR_SA_INT | SIO_IR_SA_TX_EXPLICIT | \
+				 SIO_IR_SA_MEMERR)
+#define SIO_IR_SB		(SIO_IR_SB_TX_MT | SIO_IR_SB_RX_FULL | \
+				 SIO_IR_SB_RX_HIGH | SIO_IR_SB_RX_TIMER | \
+				 SIO_IR_SB_DELTA_DCD | SIO_IR_SB_DELTA_CTS | \
+				 SIO_IR_SB_INT | SIO_IR_SB_TX_EXPLICIT | \
+				 SIO_IR_SB_MEMERR)
+#define SIO_IR_PP		(SIO_IR_PP_INT | SIO_IR_PP_INTA | \
+				 SIO_IR_PP_INTB | SIO_IR_PP_MEMERR)
+#define SIO_IR_RT		(SIO_IR_RT_INT | SIO_IR_GEN_INT1)
+
+/* bitmasks for SIO_CR */
+#define SIO_CR_SIO_RESET	0x00000001	/* reset the SIO */
+#define SIO_CR_SER_A_BASE	0x000000fe	/* DMA poll addr port A */
+#define SIO_CR_SER_A_BASE_SHIFT 1
+#define SIO_CR_SER_B_BASE	0x00007f00	/* DMA poll addr port B */
+#define SIO_CR_SER_B_BASE_SHIFT 8
+#define SIO_SR_CMD_PULSE	0x00078000	/* byte bus strobe length */
+#define SIO_CR_CMD_PULSE_SHIFT	15
+#define SIO_CR_ARB_DIAG		0x00380000	/* cur !enet PCI requet (ro) */
+#define SIO_CR_ARB_DIAG_TXA	0x00000000
+#define SIO_CR_ARB_DIAG_RXA	0x00080000
+#define SIO_CR_ARB_DIAG_TXB	0x00100000
+#define SIO_CR_ARB_DIAG_RXB	0x00180000
+#define SIO_CR_ARB_DIAG_PP	0x00200000
+#define SIO_CR_ARB_DIAG_IDLE	0x00400000	/* 0 -> active request (ro) */
+
+/* bitmasks for INT_OUT */
+#define INT_OUT_COUNT	0x0000ffff	/* pulse interval timer */
+#define INT_OUT_MODE	0x00070000	/* mode mask */
+#define INT_OUT_MODE_0	0x00000000	/* set output to 0 */
+#define INT_OUT_MODE_1	0x00040000	/* set output to 1 */
+#define INT_OUT_MODE_1PULSE 0x00050000	/* send 1 pulse */
+#define INT_OUT_MODE_PULSES 0x00060000	/* send 1 pulse every interval */
+#define INT_OUT_MODE_SQW 0x00070000	/* toggle output every interval */
+#define INT_OUT_DIAG	0x40000000	/* diag mode */
+#define INT_OUT_INT_OUT 0x80000000	/* current state of INT_OUT */
+
+/* time constants for INT_OUT */
+#define INT_OUT_NS_PER_TICK (30 * 260)	/* 30 ns PCI clock, divisor=260 */
+#define INT_OUT_TICKS_PER_PULSE 3	/* outgoing pulse lasts 3 ticks */
+#define INT_OUT_US_TO_COUNT(x)		/* convert uS to a count value */ \
+	(((x) * 10 + INT_OUT_NS_PER_TICK / 200) *	\
+	 100 / INT_OUT_NS_PER_TICK - 1)
+#define INT_OUT_COUNT_TO_US(x)		/* convert count value to uS */ \
+	(((x) + 1) * INT_OUT_NS_PER_TICK / 1000)
+#define INT_OUT_MIN_TICKS 3	/* min period is width of pulse in "ticks" */
+#define INT_OUT_MAX_TICKS INT_OUT_COUNT		/* largest possible count */
+
+/* bitmasks for GPCR */
+#define GPCR_DIR	0x000000ff	/* tristate pin input or output */
+#define GPCR_DIR_PIN(x) (1<<(x))	/* access one of the DIR bits */
+#define GPCR_EDGE	0x000f0000	/* extint edge or level sensitive */
+#define GPCR_EDGE_PIN(x) (1<<((x)+15))	/* access one of the EDGE bits */
+
+/* values for GPCR */
+#define GPCR_INT_OUT_EN 0x00100000	/* enable INT_OUT to pin 0 */
+#define GPCR_MLAN_EN	0x00200000	/* enable MCR to pin 8 */
+#define GPCR_DIR_SERA_XCVR 0x00000080	/* Port A Transceiver select enable */
+#define GPCR_DIR_SERB_XCVR 0x00000040	/* Port B Transceiver select enable */
+#define GPCR_DIR_PHY_RST   0x00000020	/* ethernet PHY reset enable */
+
+/* defs for some of the generic I/O pins */
+#define GPCR_PHY_RESET		0x20	/* pin is output to PHY reset */
+#define GPCR_UARTB_MODESEL	0x40	/* pin is output to port B mode sel */
+#define GPCR_UARTA_MODESEL	0x80	/* pin is output to port A mode sel */
+
+#define GPPR_PHY_RESET_PIN	5	/* GIO pin cntrlling phy reset */
+#define GPPR_UARTB_MODESEL_PIN	6	/* GIO pin cntrlling uart b mode sel */
+#define GPPR_UARTA_MODESEL_PIN	7	/* GIO pin cntrlling uart a mode sel */
+
+/* ethernet */
+#define EMCR_DUPLEX		0x00000001
+#define EMCR_PROMISC		0x00000002
+#define EMCR_PADEN		0x00000004
+#define EMCR_RXOFF_MASK		0x000001f8
+#define EMCR_RXOFF_SHIFT	3
+#define EMCR_RAMPAR		0x00000200
+#define EMCR_BADPAR		0x00000800
+#define EMCR_BUFSIZ		0x00001000
+#define EMCR_TXDMAEN		0x00002000
+#define EMCR_TXEN		0x00004000
+#define EMCR_RXDMAEN		0x00008000
+#define EMCR_RXEN		0x00010000
+#define EMCR_LOOPBACK		0x00020000
+#define EMCR_ARB_DIAG		0x001c0000
+#define EMCR_ARB_DIAG_IDLE	0x00200000
+#define EMCR_RST		0x80000000
+
+#define EISR_RXTIMERINT		0x00000001
+#define EISR_RXTHRESHINT	0x00000002
+#define EISR_RXOFLO		0x00000004
+#define EISR_RXBUFOFLO		0x00000008
+#define EISR_RXMEMERR		0x00000010
+#define EISR_RXPARERR		0x00000020
+#define EISR_TXEMPTY		0x00010000
+#define EISR_TXRTRY		0x00020000
+#define EISR_TXEXDEF		0x00040000
+#define EISR_TXLCOL		0x00080000
+#define EISR_TXGIANT		0x00100000
+#define EISR_TXBUFUFLO		0x00200000
+#define EISR_TXEXPLICIT		0x00400000
+#define EISR_TXCOLLWRAP		0x00800000
+#define EISR_TXDEFERWRAP	0x01000000
+#define EISR_TXMEMERR		0x02000000
+#define EISR_TXPARERR		0x04000000
+
+#define ERCSR_THRESH_MASK	0x000001ff	/* enet RX threshold */
+#define ERCSR_RX_TMR		0x40000000	/* simulation only */
+#define ERCSR_DIAG_OFLO		0x80000000	/* simulation only */
+
+#define ERBR_ALIGNMENT		4096
+#define ERBR_L_RXRINGBASE_MASK	0xfffff000
+
+#define ERBAR_BARRIER_BIT	0x0100
+#define ERBAR_RXBARR_MASK	0xffff0000
+#define ERBAR_RXBARR_SHIFT	16
+
+#define ERCIR_RXCONSUME_MASK	0x00000fff
+
+#define ERPIR_RXPRODUCE_MASK	0x00000fff
+#define ERPIR_ARM		0x80000000
+
+#define ERTR_CNT_MASK		0x000007ff
+
+#define ETCSR_IPGT_MASK		0x0000007f
+#define ETCSR_IPGR1_MASK	0x00007f00
+#define ETCSR_IPGR1_SHIFT	8
+#define ETCSR_IPGR2_MASK	0x007f0000
+#define ETCSR_IPGR2_SHIFT	16
+#define ETCSR_NOTXCLK		0x80000000
+
+#define ETCDC_COLLCNT_MASK	0x0000ffff
+#define ETCDC_DEFERCNT_MASK	0xffff0000
+#define ETCDC_DEFERCNT_SHIFT	16
+
+#define ETBR_ALIGNMENT		(64*1024)
+#define ETBR_L_RINGSZ_MASK	0x00000001
+#define ETBR_L_RINGSZ128	0
+#define ETBR_L_RINGSZ512	1
+#define ETBR_L_TXRINGBASE_MASK	0xffffc000
+
+#define ETCIR_TXCONSUME_MASK	0x0000ffff
+#define ETCIR_IDLE		0x80000000
+
+#define ETPIR_TXPRODUCE_MASK	0x0000ffff
+
+#define EBIR_TXBUFPROD_MASK	0x0000001f
+#define EBIR_TXBUFCONS_MASK	0x00001f00
+#define EBIR_TXBUFCONS_SHIFT	8
+#define EBIR_RXBUFPROD_MASK	0x007fc000
+#define EBIR_RXBUFPROD_SHIFT	14
+#define EBIR_RXBUFCONS_MASK	0xff800000
+#define EBIR_RXBUFCONS_SHIFT	23
+
+#define MICR_REGADDR_MASK	0x0000001f
+#define MICR_PHYADDR_MASK	0x000003e0
+#define MICR_PHYADDR_SHIFT	5
+#define MICR_READTRIG		0x00000400
+#define MICR_BUSY		0x00000800
+
+#define MIDR_DATA_MASK		0x0000ffff
+
+/* subsystem IDs supplied by card detection in pci-xtalk-bridge */
+#define	IOC3_SUBSYS_IP27_BASEIO6G	0xc300
+#define	IOC3_SUBSYS_IP27_MIO		0xc301
+#define	IOC3_SUBSYS_IP27_BASEIO		0xc302
+#define	IOC3_SUBSYS_IP29_SYSBOARD	0xc303
+#define	IOC3_SUBSYS_IP30_SYSBOARD	0xc304
+#define	IOC3_SUBSYS_MENET		0xc305
+#define	IOC3_SUBSYS_MENET4		0xc306
+#define	IOC3_SUBSYS_IO7			0xc307
+#define	IOC3_SUBSYS_IO8			0xc308
+#define	IOC3_SUBSYS_IO9			0xc309
+#define	IOC3_SUBSYS_IP34_SYSBOARD	0xc30A
+
+#endif /* MIPS_SN_IOC3_H */
diff --git a/arch/mips/include/asm/sn/irq_alloc.h b/arch/mips/include/asm/sn/irq_alloc.h
new file mode 100644
index 000000000..09b89cecf
--- /dev/null
+++ b/arch/mips/include/asm/sn/irq_alloc.h
@@ -0,0 +1,11 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_SN_IRQ_ALLOC_H
+#define __ASM_SN_IRQ_ALLOC_H
+
+struct irq_alloc_info {
+	void *ctrl;
+	nasid_t nasid;
+	int pin;
+};
+
+#endif /* __ASM_SN_IRQ_ALLOC_H */
diff --git a/arch/mips/include/asm/sn/klconfig.h b/arch/mips/include/asm/sn/klconfig.h
new file mode 100644
index 000000000..117f85e4b
--- /dev/null
+++ b/arch/mips/include/asm/sn/klconfig.h
@@ -0,0 +1,894 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Derived from IRIX <sys/SN/klconfig.h>.
+ *
+ * Copyright (C) 1992 - 1997, 1999, 2000 Silicon Graphics, Inc.
+ * Copyright (C) 1999, 2000 by Ralf Baechle
+ */
+#ifndef _ASM_SN_KLCONFIG_H
+#define _ASM_SN_KLCONFIG_H
+
+/*
+ * The KLCONFIG structures store info about the various BOARDs found
+ * during Hardware Discovery. In addition, it stores info about the
+ * components found on the BOARDs.
+ */
+
+/*
+ * WARNING:
+ *	Certain assembly language routines (notably xxxxx.s) in the IP27PROM
+ *	will depend on the format of the data structures in this file.	In
+ *	most cases, rearranging the fields can seriously break things.
+ *	Adding fields in the beginning or middle can also break things.
+ *	Add fields if necessary, to the end of a struct in such a way
+ *	that offsets of existing fields do not change.
+ */
+
+#include <linux/types.h>
+#include <asm/sn/types.h>
+
+#if defined(CONFIG_SGI_IP27)
+
+#include <asm/sn/sn0/addrs.h>
+//#include <sys/SN/router.h>
+// XXX Stolen from <sys/SN/router.h>:
+#define MAX_ROUTER_PORTS (6)	/* Max. number of ports on a router */
+#include <asm/sn/fru.h>
+//#include <sys/graph.h>
+//#include <sys/xtalk/xbow.h>
+
+#elif defined(CONFIG_SGI_IP35)
+
+#include <asm/sn/sn1/addrs.h>
+#include <sys/sn/router.h>
+#include <sys/graph.h>
+#include <asm/xtalk/xbow.h>
+
+#endif /* !CONFIG_SGI_IP27 && !CONFIG_SGI_IP35 */
+
+#if defined(CONFIG_SGI_IP27) || defined(CONFIG_SGI_IP35)
+#include <asm/sn/agent.h>
+#include <asm/fw/arc/types.h>
+#include <asm/fw/arc/hinv.h>
+#if defined(CONFIG_SGI_IP35)
+// The hack file has to be before vector and after sn0_fru....
+#include <asm/hack.h>
+#include <asm/sn/vector.h>
+#include <asm/xtalk/xtalk.h>
+#endif /* CONFIG_SGI_IP35 */
+#endif /* CONFIG_SGI_IP27 || CONFIG_SGI_IP35 */
+
+typedef u64  nic_t;
+
+#define KLCFGINFO_MAGIC 0xbeedbabe
+
+typedef s32 klconf_off_t;
+
+/*
+ * Some IMPORTANT OFFSETS. These are the offsets on all NODES.
+ */
+#define MAX_MODULE_ID		255
+#define SIZE_PAD		4096 /* 4k padding for structures */
+/*
+ * 1 NODE brd, 2 Router brd (1 8p, 1 meta), 6 Widgets,
+ * 2 Midplanes assuming no pci card cages
+ */
+#define MAX_SLOTS_PER_NODE	(1 + 2 + 6 + 2)
+
+/* XXX if each node is guaranteed to have some memory */
+
+#define MAX_PCI_DEVS		8
+
+/* lboard_t->brd_flags fields */
+/* All bits in this field are currently used. Try the pad fields if
+   you need more flag bits */
+
+#define ENABLE_BOARD		0x01
+#define FAILED_BOARD		0x02
+#define DUPLICATE_BOARD		0x04	/* Boards like midplanes/routers which
+					   are discovered twice. Use one of them */
+#define VISITED_BOARD		0x08	/* Used for compact hub numbering. */
+#define LOCAL_MASTER_IO6	0x10	/* master io6 for that node */
+#define GLOBAL_MASTER_IO6	0x20
+#define THIRD_NIC_PRESENT	0x40	/* for future use */
+#define SECOND_NIC_PRESENT	0x80	/* addons like MIO are present */
+
+/* klinfo->flags fields */
+
+#define KLINFO_ENABLE		0x01	/* This component is enabled */
+#define KLINFO_FAILED		0x02	/* This component failed */
+#define KLINFO_DEVICE		0x04	/* This component is a device */
+#define KLINFO_VISITED		0x08	/* This component has been visited */
+#define KLINFO_CONTROLLER	0x10	/* This component is a device controller */
+#define KLINFO_INSTALL		0x20	/* Install a driver */
+#define KLINFO_HEADLESS		0x40	/* Headless (or hubless) component */
+#define IS_CONSOLE_IOC3(i)	((((klinfo_t *)i)->flags) & KLINFO_INSTALL)
+
+#define GB2		0x80000000
+
+#define MAX_RSV_PTRS	32
+
+/* Structures to manage various data storage areas */
+/* The numbers must be contiguous since the array index i
+   is used in the code to allocate various areas.
+*/
+
+#define BOARD_STRUCT		0
+#define COMPONENT_STRUCT	1
+#define ERRINFO_STRUCT		2
+#define KLMALLOC_TYPE_MAX	(ERRINFO_STRUCT + 1)
+#define DEVICE_STRUCT		3
+
+
+typedef struct console_s {
+	unsigned long	uart_base;
+	unsigned long	config_base;
+	unsigned long	memory_base;
+	short		baud;
+	short		flag;
+	int		type;
+	nasid_t		nasid;
+	char		wid;
+	char		npci;
+	nic_t		baseio_nic;
+} console_t;
+
+typedef struct klc_malloc_hdr {
+	klconf_off_t km_base;
+	klconf_off_t km_limit;
+	klconf_off_t km_current;
+} klc_malloc_hdr_t;
+
+/* Functions/macros needed to use this structure */
+
+typedef struct kl_config_hdr {
+	u64		ch_magic;	/* set this to KLCFGINFO_MAGIC */
+	u32		ch_version;    /* structure version number */
+	klconf_off_t	ch_malloc_hdr_off; /* offset of ch_malloc_hdr */
+	klconf_off_t	ch_cons_off;	   /* offset of ch_cons */
+	klconf_off_t	ch_board_info;	/* the link list of boards */
+	console_t	ch_cons_info;	/* address info of the console */
+	klc_malloc_hdr_t ch_malloc_hdr[KLMALLOC_TYPE_MAX];
+	confidence_t	ch_sw_belief;	/* confidence that software is bad*/
+	confidence_t	ch_sn0net_belief; /* confidence that sn0net is bad */
+} kl_config_hdr_t;
+
+
+#define KL_CONFIG_HDR(_nasid)	((kl_config_hdr_t *)(KLCONFIG_ADDR(_nasid)))
+#define KL_CONFIG_INFO_OFFSET(_nasid)					\
+	(KL_CONFIG_HDR(_nasid)->ch_board_info)
+#define KL_CONFIG_INFO_SET_OFFSET(_nasid, _off)				\
+	(KL_CONFIG_HDR(_nasid)->ch_board_info = (_off))
+
+#define KL_CONFIG_INFO(_nasid)						\
+	(lboard_t *)((KL_CONFIG_HDR(_nasid)->ch_board_info) ?		\
+	 NODE_OFFSET_TO_K1((_nasid), KL_CONFIG_HDR(_nasid)->ch_board_info) : \
+	 0)
+#define KL_CONFIG_MAGIC(_nasid)		(KL_CONFIG_HDR(_nasid)->ch_magic)
+
+#define KL_CONFIG_CHECK_MAGIC(_nasid)					\
+	(KL_CONFIG_HDR(_nasid)->ch_magic == KLCFGINFO_MAGIC)
+
+#define KL_CONFIG_HDR_INIT_MAGIC(_nasid)	\
+		  (KL_CONFIG_HDR(_nasid)->ch_magic = KLCFGINFO_MAGIC)
+
+/* --- New Macros for the changed kl_config_hdr_t structure --- */
+
+#define PTR_CH_MALLOC_HDR(_k)	((klc_malloc_hdr_t *)\
+			((unsigned long)_k + (_k->ch_malloc_hdr_off)))
+
+#define KL_CONFIG_CH_MALLOC_HDR(_n)   PTR_CH_MALLOC_HDR(KL_CONFIG_HDR(_n))
+
+#define PTR_CH_CONS_INFO(_k)	((console_t *)\
+			((unsigned long)_k + (_k->ch_cons_off)))
+
+#define KL_CONFIG_CH_CONS_INFO(_n)   PTR_CH_CONS_INFO(KL_CONFIG_HDR(_n))
+
+/* ------------------------------------------------------------- */
+
+#define KL_CONFIG_INFO_START(_nasid)	\
+	(klconf_off_t)(KLCONFIG_OFFSET(_nasid) + sizeof(kl_config_hdr_t))
+
+#define KL_CONFIG_BOARD_NASID(_brd)	((_brd)->brd_nasid)
+#define KL_CONFIG_BOARD_SET_NEXT(_brd, _off)	((_brd)->brd_next = (_off))
+
+#define KL_CONFIG_DUPLICATE_BOARD(_brd) ((_brd)->brd_flags & DUPLICATE_BOARD)
+
+#define XBOW_PORT_TYPE_HUB(_xbowp, _link)	\
+	       ((_xbowp)->xbow_port_info[(_link) - BASE_XBOW_PORT].port_flag & XBOW_PORT_HUB)
+#define XBOW_PORT_TYPE_IO(_xbowp, _link)	\
+	       ((_xbowp)->xbow_port_info[(_link) - BASE_XBOW_PORT].port_flag & XBOW_PORT_IO)
+
+#define XBOW_PORT_IS_ENABLED(_xbowp, _link)	\
+	       ((_xbowp)->xbow_port_info[(_link) - BASE_XBOW_PORT].port_flag & XBOW_PORT_ENABLE)
+#define XBOW_PORT_NASID(_xbowp, _link)	\
+	       ((_xbowp)->xbow_port_info[(_link) - BASE_XBOW_PORT].port_nasid)
+
+#define XBOW_PORT_IO	 0x1
+#define XBOW_PORT_HUB	 0x2
+#define XBOW_PORT_ENABLE 0x4
+
+#define SN0_PORT_FENCE_SHFT	0
+#define SN0_PORT_FENCE_MASK	(1 << SN0_PORT_FENCE_SHFT)
+
+/*
+ * The KLCONFIG area is organized as a LINKED LIST of BOARDs. A BOARD
+ * can be either 'LOCAL' or 'REMOTE'. LOCAL means it is attached to
+ * the LOCAL/current NODE. REMOTE means it is attached to a different
+ * node.(TBD - Need a way to treat ROUTER boards.)
+ *
+ * There are 2 different structures to represent these boards -
+ * lboard - Local board, rboard - remote board. These 2 structures
+ * can be arbitrarily mixed in the LINKED LIST of BOARDs. (Refer
+ * Figure below). The first byte of the rboard or lboard structure
+ * is used to find out its type - no unions are used.
+ * If it is a lboard, then the config info of this board will be found
+ * on the local node. (LOCAL NODE BASE + offset value gives pointer to
+ * the structure.
+ * If it is a rboard, the local structure contains the node number
+ * and the offset of the beginning of the LINKED LIST on the remote node.
+ * The details of the hardware on a remote node can be built locally,
+ * if required, by reading the LINKED LIST on the remote node and
+ * ignoring all the rboards on that node.
+ *
+ * The local node uses the REMOTE NODE NUMBER + OFFSET to point to the
+ * First board info on the remote node. The remote node list is
+ * traversed as the local list, using the REMOTE BASE ADDRESS and not
+ * the local base address and ignoring all rboard values.
+ *
+ *
+ KLCONFIG
+
+ +------------+	     +------------+	 +------------+	     +------------+
+ |  lboard    |	 +-->|	 lboard	  |  +-->|   rboard   |	 +-->|	 lboard	  |
+ +------------+	 |   +------------+  |	 +------------+	 |   +------------+
+ | board info |	 |   | board info |  |	 |errinfo,bptr|	 |   | board info |
+ +------------+	 |   +------------+  |	 +------------+	 |   +------------+
+ | offset     |--+   |	offset	  |--+	 |  offset    |--+   |offset=NULL |
+ +------------+	     +------------+	 +------------+	     +------------+
+
+
+ +------------+
+ | board info |
+ +------------+	      +--------------------------------+
+ | compt 1    |------>| type, rev, diaginfo, size ...  |  (CPU)
+ +------------+	      +--------------------------------+
+ | compt 2    |--+
+ +------------+	 |    +--------------------------------+
+ |  ...	      |	 +--->| type, rev, diaginfo, size ...  |  (MEM_BANK)
+ +------------+	      +--------------------------------+
+ | errinfo    |--+
+ +------------+	 |    +--------------------------------+
+		 +--->|r/l brd errinfo,compt err flags |
+		      +--------------------------------+
+
+ *
+ * Each BOARD consists of COMPONENTs and the BOARD structure has
+ * pointers (offsets) to its COMPONENT structure.
+ * The COMPONENT structure has version info, size and speed info, revision,
+ * error info and the NIC info. This structure can accommodate any
+ * BOARD with arbitrary COMPONENT composition.
+ *
+ * The ERRORINFO part of each BOARD has error information
+ * that describes errors about the BOARD itself. It also has flags to
+ * indicate the COMPONENT(s) on the board that have errors. The error
+ * information specific to the COMPONENT is present in the respective
+ * COMPONENT structure.
+ *
+ * The ERRORINFO structure is also treated like a COMPONENT, ie. the
+ * BOARD has pointers(offset) to the ERRORINFO structure. The rboard
+ * structure also has a pointer to the ERRORINFO structure. This is
+ * the place to store ERRORINFO about a REMOTE NODE, if the HUB on
+ * that NODE is not working or if the REMOTE MEMORY is BAD. In cases where
+ * only the CPU of the REMOTE NODE is disabled, the ERRORINFO pointer can
+ * be a NODE NUMBER, REMOTE OFFSET combination, pointing to error info
+ * which is present on the REMOTE NODE.(TBD)
+ * REMOTE ERRINFO can be stored on any of the nearest nodes
+ * or on all the nearest nodes.(TBD)
+ * Like BOARD structures, REMOTE ERRINFO structures can be built locally
+ * using the rboard errinfo pointer.
+ *
+ * In order to get useful information from this Data organization, a set of
+ * interface routines are provided (TBD). The important thing to remember while
+ * manipulating the structures, is that, the NODE number information should
+ * be used. If the NODE is non-zero (remote) then each offset should
+ * be added to the REMOTE BASE ADDR else it should be added to the LOCAL BASE ADDR.
+ * This includes offsets for BOARDS, COMPONENTS and ERRORINFO.
+ *
+ * Note that these structures do not provide much info about connectivity.
+ * That info will be part of HWGRAPH, which is an extension of the cfg_t
+ * data structure. (ref IP27prom/cfg.h) It has to be extended to include
+ * the IO part of the Network(TBD).
+ *
+ * The data structures below define the above concepts.
+ */
+
+/*
+ * Values for CPU types
+ */
+#define KL_CPU_R4000		0x1	/* Standard R4000 */
+#define KL_CPU_TFP		0x2	/* TFP processor */
+#define KL_CPU_R10000		0x3	/* R10000 (T5) */
+#define KL_CPU_NONE		(-1)	/* no cpu present in slot */
+
+/*
+ * IP27 BOARD classes
+ */
+
+#define KLCLASS_MASK	0xf0
+#define KLCLASS_NONE	0x00
+#define KLCLASS_NODE	0x10		 /* CPU, Memory and HUB board */
+#define KLCLASS_CPU	KLCLASS_NODE
+#define KLCLASS_IO	0x20		 /* BaseIO, 4 ch SCSI, ethernet, FDDI
+					    and the non-graphics widget boards */
+#define KLCLASS_ROUTER	0x30		 /* Router board */
+#define KLCLASS_MIDPLANE 0x40		 /* We need to treat this as a board
+					    so that we can record error info */
+#define KLCLASS_GFX	0x50		/* graphics boards */
+
+#define KLCLASS_PSEUDO_GFX	0x60	/* HDTV type cards that use a gfx
+					 * hw ifc to xtalk and are not gfx
+					 * class for sw purposes */
+
+#define KLCLASS_MAX	7		/* Bump this if a new CLASS is added */
+#define KLTYPE_MAX	10		/* Bump this if a new CLASS is added */
+
+#define KLCLASS_UNKNOWN 0xf0
+
+#define KLCLASS(_x) ((_x) & KLCLASS_MASK)
+
+/*
+ * IP27 board types
+ */
+
+#define KLTYPE_MASK	0x0f
+#define KLTYPE_NONE	0x00
+#define KLTYPE_EMPTY	0x00
+
+#define KLTYPE_WEIRDCPU (KLCLASS_CPU | 0x0)
+#define KLTYPE_IP27	(KLCLASS_CPU | 0x1) /* 2 CPUs(R10K) per board */
+
+#define KLTYPE_WEIRDIO	(KLCLASS_IO  | 0x0)
+#define KLTYPE_BASEIO	(KLCLASS_IO  | 0x1) /* IOC3, SuperIO, Bridge, SCSI */
+#define KLTYPE_IO6	KLTYPE_BASEIO	    /* Additional name */
+#define KLTYPE_4CHSCSI	(KLCLASS_IO  | 0x2)
+#define KLTYPE_MSCSI	KLTYPE_4CHSCSI	    /* Additional name */
+#define KLTYPE_ETHERNET (KLCLASS_IO  | 0x3)
+#define KLTYPE_MENET	KLTYPE_ETHERNET	    /* Additional name */
+#define KLTYPE_FDDI	(KLCLASS_IO  | 0x4)
+#define KLTYPE_UNUSED	(KLCLASS_IO  | 0x5) /* XXX UNUSED */
+#define KLTYPE_HAROLD	(KLCLASS_IO  | 0x6) /* PCI SHOE BOX */
+#define KLTYPE_PCI	KLTYPE_HAROLD
+#define KLTYPE_VME	(KLCLASS_IO  | 0x7) /* Any 3rd party VME card */
+#define KLTYPE_MIO	(KLCLASS_IO  | 0x8)
+#define KLTYPE_FC	(KLCLASS_IO  | 0x9)
+#define KLTYPE_LINC	(KLCLASS_IO  | 0xA)
+#define KLTYPE_TPU	(KLCLASS_IO  | 0xB) /* Tensor Processing Unit */
+#define KLTYPE_GSN_A	(KLCLASS_IO  | 0xC) /* Main GSN board */
+#define KLTYPE_GSN_B	(KLCLASS_IO  | 0xD) /* Auxiliary GSN board */
+
+#define KLTYPE_GFX	(KLCLASS_GFX | 0x0) /* unknown graphics type */
+#define KLTYPE_GFX_KONA (KLCLASS_GFX | 0x1) /* KONA graphics on IP27 */
+#define KLTYPE_GFX_MGRA (KLCLASS_GFX | 0x3) /* MGRAS graphics on IP27 */
+
+#define KLTYPE_WEIRDROUTER (KLCLASS_ROUTER | 0x0)
+#define KLTYPE_ROUTER	  (KLCLASS_ROUTER | 0x1)
+#define KLTYPE_ROUTER2	  KLTYPE_ROUTER		/* Obsolete! */
+#define KLTYPE_NULL_ROUTER (KLCLASS_ROUTER | 0x2)
+#define KLTYPE_META_ROUTER (KLCLASS_ROUTER | 0x3)
+
+#define KLTYPE_WEIRDMIDPLANE (KLCLASS_MIDPLANE | 0x0)
+#define KLTYPE_MIDPLANE8  (KLCLASS_MIDPLANE | 0x1) /* 8 slot backplane */
+#define KLTYPE_MIDPLANE	   KLTYPE_MIDPLANE8
+#define KLTYPE_PBRICK_XBOW	(KLCLASS_MIDPLANE | 0x2)
+
+#define KLTYPE_IOBRICK		(KLCLASS_IOBRICK | 0x0)
+#define KLTYPE_IBRICK		(KLCLASS_IOBRICK | 0x1)
+#define KLTYPE_PBRICK		(KLCLASS_IOBRICK | 0x2)
+#define KLTYPE_XBRICK		(KLCLASS_IOBRICK | 0x3)
+
+#define KLTYPE_PBRICK_BRIDGE	KLTYPE_PBRICK
+
+/* The value of type should be more than 8 so that hinv prints
+ * out the board name from the NIC string. For values less than
+ * 8 the name of the board needs to be hard coded in a few places.
+ * When bringup started nic names had not standardized and so we
+ * had to hard code. (For people interested in history.)
+ */
+#define KLTYPE_XTHD	(KLCLASS_PSEUDO_GFX | 0x9)
+
+#define KLTYPE_UNKNOWN	(KLCLASS_UNKNOWN | 0xf)
+
+#define KLTYPE(_x)	((_x) & KLTYPE_MASK)
+#define IS_MIO_PRESENT(l)	((l->brd_type == KLTYPE_BASEIO) && \
+				 (l->brd_flags & SECOND_NIC_PRESENT))
+#define IS_MIO_IOC3(l, n)	(IS_MIO_PRESENT(l) && (n > 2))
+
+/*
+ * board structures
+ */
+
+#define MAX_COMPTS_PER_BRD 24
+
+#define LOCAL_BOARD 1
+#define REMOTE_BOARD 2
+
+#define LBOARD_STRUCT_VERSION	2
+
+typedef struct lboard_s {
+	klconf_off_t	brd_next;	  /* Next BOARD */
+	unsigned char	struct_type;	  /* type of structure, local or remote */
+	unsigned char	brd_type;	  /* type+class */
+	unsigned char	brd_sversion;	  /* version of this structure */
+	unsigned char	brd_brevision;	  /* board revision */
+	unsigned char	brd_promver;	  /* board prom version, if any */
+	unsigned char	brd_flags;	  /* Enabled, Disabled etc */
+	unsigned char	brd_slot;	  /* slot number */
+	unsigned short	brd_debugsw;	  /* Debug switches */
+	moduleid_t	brd_module;	  /* module to which it belongs */
+	partid_t	brd_partition;	  /* Partition number */
+	unsigned short	brd_diagval;	  /* diagnostic value */
+	unsigned short	brd_diagparm;	  /* diagnostic parameter */
+	unsigned char	brd_inventory;	  /* inventory history */
+	unsigned char	brd_numcompts;	  /* Number of components */
+	nic_t		brd_nic;	  /* Number in CAN */
+	nasid_t		brd_nasid;	  /* passed parameter */
+	klconf_off_t	brd_compts[MAX_COMPTS_PER_BRD]; /* pointers to COMPONENTS */
+	klconf_off_t	brd_errinfo;	  /* Board's error information */
+	struct lboard_s *brd_parent;	  /* Logical parent for this brd */
+	vertex_hdl_t	brd_graph_link;	  /* vertex hdl to connect extern compts */
+	confidence_t	brd_confidence;	  /* confidence that the board is bad */
+	nasid_t		brd_owner;	  /* who owns this board */
+	unsigned char	brd_nic_flags;	  /* To handle 8 more NICs */
+	char		brd_name[32];
+} lboard_t;
+
+
+/*
+ *	Make sure we pass back the calias space address for local boards.
+ *	klconfig board traversal and error structure extraction defines.
+ */
+
+#define BOARD_SLOT(_brd)	((_brd)->brd_slot)
+
+#define KLCF_CLASS(_brd)	KLCLASS((_brd)->brd_type)
+#define KLCF_TYPE(_brd)		KLTYPE((_brd)->brd_type)
+#define KLCF_REMOTE(_brd)	(((_brd)->struct_type & LOCAL_BOARD) ? 0 : 1)
+#define KLCF_NUM_COMPS(_brd)	((_brd)->brd_numcompts)
+#define KLCF_MODULE_ID(_brd)	((_brd)->brd_module)
+
+#define KLCF_NEXT(_brd)		\
+	((_brd)->brd_next ?	\
+	 (lboard_t *)(NODE_OFFSET_TO_K1(NASID_GET(_brd), (_brd)->brd_next)):\
+	 NULL)
+#define KLCF_COMP(_brd, _ndx)	\
+		(klinfo_t *)(NODE_OFFSET_TO_K1(NASID_GET(_brd), \
+					       (_brd)->brd_compts[(_ndx)]))
+
+#define KLCF_COMP_ERROR(_brd, _comp)	\
+	       (NODE_OFFSET_TO_K1(NASID_GET(_brd), (_comp)->errinfo))
+
+#define KLCF_COMP_TYPE(_comp)	((_comp)->struct_type)
+#define KLCF_BRIDGE_W_ID(_comp) ((_comp)->physid)	/* Widget ID */
+
+
+
+/*
+ * Generic info structure. This stores common info about a
+ * component.
+ */
+
+typedef struct klinfo_s {		   /* Generic info */
+	unsigned char	struct_type;	   /* type of this structure */
+	unsigned char	struct_version;	   /* version of this structure */
+	unsigned char	flags;		  /* Enabled, disabled etc */
+	unsigned char	revision;	  /* component revision */
+	unsigned short	diagval;	  /* result of diagnostics */
+	unsigned short	diagparm;	  /* diagnostic parameter */
+	unsigned char	inventory;	  /* previous inventory status */
+	nic_t		nic;		  /* MUst be aligned properly */
+	unsigned char	physid;		  /* physical id of component */
+	unsigned int	virtid;		  /* virtual id as seen by system */
+	unsigned char	widid;		  /* Widget id - if applicable */
+	nasid_t		nasid;		  /* node number - from parent */
+	char		pad1;		  /* pad out structure. */
+	char		pad2;		  /* pad out structure. */
+	COMPONENT	*arcs_compt;	  /* ptr to the arcs struct for ease*/
+	klconf_off_t	errinfo;	  /* component specific errors */
+	unsigned short	pad3;		  /* pci fields have moved over to */
+	unsigned short	pad4;		  /* klbri_t */
+} klinfo_t ;
+
+#define KLCONFIG_INFO_ENABLED(_i)	((_i)->flags & KLINFO_ENABLE)
+/*
+ * Component structures.
+ * Following are the currently identified components:
+ *	CPU, HUB, MEM_BANK,
+ *	XBOW(consists of 16 WIDGETs, each of which can be HUB or GRAPHICS or BRIDGE)
+ *	BRIDGE, IOC3, SuperIO, SCSI, FDDI
+ *	ROUTER
+ *	GRAPHICS
+ */
+#define KLSTRUCT_UNKNOWN	0
+#define KLSTRUCT_CPU		1
+#define KLSTRUCT_HUB		2
+#define KLSTRUCT_MEMBNK		3
+#define KLSTRUCT_XBOW		4
+#define KLSTRUCT_BRI		5
+#define KLSTRUCT_IOC3		6
+#define KLSTRUCT_PCI		7
+#define KLSTRUCT_VME		8
+#define KLSTRUCT_ROU		9
+#define KLSTRUCT_GFX		10
+#define KLSTRUCT_SCSI		11
+#define KLSTRUCT_FDDI		12
+#define KLSTRUCT_MIO		13
+#define KLSTRUCT_DISK		14
+#define KLSTRUCT_TAPE		15
+#define KLSTRUCT_CDROM		16
+#define KLSTRUCT_HUB_UART	17
+#define KLSTRUCT_IOC3ENET	18
+#define KLSTRUCT_IOC3UART	19
+#define KLSTRUCT_UNUSED		20 /* XXX UNUSED */
+#define KLSTRUCT_IOC3PCKM	21
+#define KLSTRUCT_RAD		22
+#define KLSTRUCT_HUB_TTY	23
+#define KLSTRUCT_IOC3_TTY	24
+
+/* Early Access IO proms are compatible
+   only with KLSTRUCT values up to 24. */
+
+#define KLSTRUCT_FIBERCHANNEL	25
+#define KLSTRUCT_MOD_SERIAL_NUM 26
+#define KLSTRUCT_IOC3MS		27
+#define KLSTRUCT_TPU		28
+#define KLSTRUCT_GSN_A		29
+#define KLSTRUCT_GSN_B		30
+#define KLSTRUCT_XTHD		31
+
+/*
+ * These are the indices of various components within a lboard structure.
+ */
+
+#define IP27_CPU0_INDEX 0
+#define IP27_CPU1_INDEX 1
+#define IP27_HUB_INDEX 2
+#define IP27_MEM_INDEX 3
+
+#define BASEIO_BRIDGE_INDEX 0
+#define BASEIO_IOC3_INDEX 1
+#define BASEIO_SCSI1_INDEX 2
+#define BASEIO_SCSI2_INDEX 3
+
+#define MIDPLANE_XBOW_INDEX 0
+#define ROUTER_COMPONENT_INDEX 0
+
+#define CH4SCSI_BRIDGE_INDEX 0
+
+/* Info holders for various hardware components */
+
+typedef u64 *pci_t;
+typedef u64 *vmeb_t;
+typedef u64 *vmed_t;
+typedef u64 *fddi_t;
+typedef u64 *scsi_t;
+typedef u64 *mio_t;
+typedef u64 *graphics_t;
+typedef u64 *router_t;
+
+/*
+ * The port info in ip27_cfg area translates to a lboart_t in the
+ * KLCONFIG area. But since KLCONFIG does not use pointers, lboart_t
+ * is stored in terms of a nasid and a offset from start of KLCONFIG
+ * area	 on that nasid.
+ */
+typedef struct klport_s {
+	nasid_t		port_nasid;
+	unsigned char	port_flag;
+	klconf_off_t	port_offset;
+} klport_t;
+
+typedef struct klcpu_s {			  /* CPU */
+	klinfo_t	cpu_info;
+	unsigned short	cpu_prid;	/* Processor PRID value */
+	unsigned short	cpu_fpirr;	/* FPU IRR value */
+	unsigned short	cpu_speed;	/* Speed in MHZ */
+	unsigned short	cpu_scachesz;	/* secondary cache size in MB */
+	unsigned short	cpu_scachespeed;/* secondary cache speed in MHz */
+} klcpu_t ;
+
+#define CPU_STRUCT_VERSION   2
+
+typedef struct klhub_s {			/* HUB */
+	klinfo_t	hub_info;
+	unsigned int		hub_flags;		/* PCFG_HUB_xxx flags */
+	klport_t	hub_port;		/* hub is connected to this */
+	nic_t		hub_box_nic;		/* nic of containing box */
+	klconf_off_t	hub_mfg_nic;		/* MFG NIC string */
+	u64		hub_speed;		/* Speed of hub in HZ */
+} klhub_t ;
+
+typedef struct klhub_uart_s {			/* HUB */
+	klinfo_t	hubuart_info;
+	unsigned int		hubuart_flags;		/* PCFG_HUB_xxx flags */
+	nic_t		hubuart_box_nic;	/* nic of containing box */
+} klhub_uart_t ;
+
+#define MEMORY_STRUCT_VERSION	2
+
+typedef struct klmembnk_s {			/* MEMORY BANK */
+	klinfo_t	membnk_info;
+	short		membnk_memsz;		/* Total memory in megabytes */
+	short		membnk_dimm_select; /* bank to physical addr mapping*/
+	short		membnk_bnksz[MD_MEM_BANKS]; /* Memory bank sizes */
+	short		membnk_attr;
+} klmembnk_t ;
+
+#define KLCONFIG_MEMBNK_SIZE(_info, _bank)	\
+			    ((_info)->membnk_bnksz[(_bank)])
+
+
+#define MEMBNK_PREMIUM 1
+#define KLCONFIG_MEMBNK_PREMIUM(_info, _bank)	\
+			    ((_info)->membnk_attr & (MEMBNK_PREMIUM << (_bank)))
+
+#define MAX_SERIAL_NUM_SIZE 10
+
+typedef struct klmod_serial_num_s {
+      klinfo_t	      snum_info;
+      union {
+	      char snum_str[MAX_SERIAL_NUM_SIZE];
+	      unsigned long long       snum_int;
+      } snum;
+} klmod_serial_num_t;
+
+/* Macros needed to access serial number structure in lboard_t.
+   Hard coded values are necessary since we cannot treat
+   serial number struct as a component without losing compatibility
+   between prom versions. */
+
+#define GET_SNUM_COMP(_l)	((klmod_serial_num_t *)\
+				KLCF_COMP(_l, _l->brd_numcompts))
+
+#define MAX_XBOW_LINKS 16
+
+typedef struct klxbow_s {			   /* XBOW */
+	klinfo_t	xbow_info ;
+	klport_t	xbow_port_info[MAX_XBOW_LINKS] ; /* Module number */
+	int		xbow_master_hub_link;
+	/* type of brd connected+component struct ptr+flags */
+} klxbow_t ;
+
+#define MAX_PCI_SLOTS 8
+
+typedef struct klpci_device_s {
+	s32	pci_device_id;	/* 32 bits of vendor/device ID. */
+	s32	pci_device_pad; /* 32 bits of padding. */
+} klpci_device_t;
+
+#define BRIDGE_STRUCT_VERSION	2
+
+typedef struct klbri_s {			  /* BRIDGE */
+	klinfo_t	bri_info ;
+	unsigned char	bri_eprominfo ;	   /* IO6prom connected to bridge */
+	unsigned char	bri_bustype ;	   /* PCI/VME BUS bridge/GIO */
+	pci_t		pci_specific  ;	   /* PCI Board config info */
+	klpci_device_t	bri_devices[MAX_PCI_DEVS] ;	/* PCI IDs */
+	klconf_off_t	bri_mfg_nic ;
+} klbri_t ;
+
+#define MAX_IOC3_TTY	2
+
+typedef struct klioc3_s {			   /* IOC3 */
+	klinfo_t	ioc3_info ;
+	unsigned char	ioc3_ssram ;	    /* Info about ssram */
+	unsigned char	ioc3_nvram ;	    /* Info about nvram */
+	klinfo_t	ioc3_superio ;	    /* Info about superio */
+	klconf_off_t	ioc3_tty_off ;
+	klinfo_t	ioc3_enet ;
+	klconf_off_t	ioc3_enet_off ;
+	klconf_off_t	ioc3_kbd_off ;
+} klioc3_t ;
+
+#define MAX_VME_SLOTS 8
+
+typedef struct klvmeb_s {			   /* VME BRIDGE - PCI CTLR */
+	klinfo_t	vmeb_info ;
+	vmeb_t		vmeb_specific ;
+	klconf_off_t	vmeb_brdinfo[MAX_VME_SLOTS]   ;	   /* VME Board config info */
+} klvmeb_t ;
+
+typedef struct klvmed_s {			   /* VME DEVICE - VME BOARD */
+	klinfo_t	vmed_info ;
+	vmed_t		vmed_specific ;
+	klconf_off_t	vmed_brdinfo[MAX_VME_SLOTS]   ;	   /* VME Board config info */
+} klvmed_t ;
+
+#define ROUTER_VECTOR_VERS	2
+
+/* XXX - Don't we need the number of ports here?!? */
+typedef struct klrou_s {			  /* ROUTER */
+	klinfo_t	rou_info ;
+	unsigned int		rou_flags ;	      /* PCFG_ROUTER_xxx flags */
+	nic_t		rou_box_nic ;	      /* nic of the containing module */
+	klport_t	rou_port[MAX_ROUTER_PORTS + 1] ; /* array index 1 to 6 */
+	klconf_off_t	rou_mfg_nic ;	  /* MFG NIC string */
+	u64	rou_vector;	  /* vector from master node */
+} klrou_t ;
+
+/*
+ *  Graphics Controller/Device
+ *
+ *  (IP27/IO6) Prom versions 6.13 (and 6.5.1 kernels) and earlier
+ *  used a couple different structures to store graphics information.
+ *  For compatibility reasons, the newer data structure preserves some
+ *  of the layout so that fields that are used in the old versions remain
+ *  in the same place (with the same info).  Determination of what version
+ *  of this structure we have is done by checking the cookie field.
+ */
+#define KLGFX_COOKIE	0x0c0de000
+
+typedef struct klgfx_s {		/* GRAPHICS Device */
+	klinfo_t	gfx_info;
+	klconf_off_t	old_gndevs;	/* for compatibility with older proms */
+	klconf_off_t	old_gdoff0;	/* for compatibility with older proms */
+	unsigned int		cookie;		/* for compatibility with older proms */
+	unsigned int		moduleslot;
+	struct klgfx_s	*gfx_next_pipe;
+	graphics_t	gfx_specific;
+	klconf_off_t	pad0;		/* for compatibility with older proms */
+	klconf_off_t	gfx_mfg_nic;
+} klgfx_t;
+
+typedef struct klxthd_s {
+	klinfo_t	xthd_info ;
+	klconf_off_t	xthd_mfg_nic ;	      /* MFG NIC string */
+} klxthd_t ;
+
+typedef struct kltpu_s {		     /* TPU board */
+	klinfo_t	tpu_info ;
+	klconf_off_t	tpu_mfg_nic ;	     /* MFG NIC string */
+} kltpu_t ;
+
+typedef struct klgsn_s {		     /* GSN board */
+	klinfo_t	gsn_info ;
+	klconf_off_t	gsn_mfg_nic ;	     /* MFG NIC string */
+} klgsn_t ;
+
+#define MAX_SCSI_DEVS 16
+
+/*
+ * NOTE: THis is the max sized kl* structure and is used in klmalloc.c
+ * to allocate space of type COMPONENT. Make sure that if the size of
+ * any other component struct becomes more than this, then redefine
+ * that as the size to be klmalloced.
+ */
+
+typedef struct klscsi_s {			   /* SCSI Controller */
+	klinfo_t	scsi_info ;
+	scsi_t		scsi_specific	;
+	unsigned char	scsi_numdevs ;
+	klconf_off_t	scsi_devinfo[MAX_SCSI_DEVS] ;
+} klscsi_t ;
+
+typedef struct klscdev_s {			    /* SCSI device */
+	klinfo_t	scdev_info ;
+	struct scsidisk_data *scdev_cfg ; /* driver fills up this */
+} klscdev_t ;
+
+typedef struct klttydev_s {			     /* TTY device */
+	klinfo_t	ttydev_info ;
+	struct terminal_data *ttydev_cfg ; /* driver fills up this */
+} klttydev_t ;
+
+typedef struct klenetdev_s {			      /* ENET device */
+	klinfo_t	enetdev_info ;
+	struct net_data *enetdev_cfg ; /* driver fills up this */
+} klenetdev_t ;
+
+typedef struct klkbddev_s {			     /* KBD device */
+	klinfo_t	kbddev_info ;
+	struct keyboard_data *kbddev_cfg ; /* driver fills up this */
+} klkbddev_t ;
+
+typedef struct klmsdev_s {			    /* mouse device */
+	klinfo_t	msdev_info ;
+	void		*msdev_cfg ;
+} klmsdev_t ;
+
+#define MAX_FDDI_DEVS 10 /* XXX Is this true */
+
+typedef struct klfddi_s {			   /* FDDI */
+	klinfo_t	fddi_info ;
+	fddi_t		fddi_specific ;
+	klconf_off_t	fddi_devinfo[MAX_FDDI_DEVS] ;
+} klfddi_t ;
+
+typedef struct klmio_s {			  /* MIO */
+	klinfo_t	mio_info ;
+	mio_t		mio_specific   ;
+} klmio_t ;
+
+
+typedef union klcomp_s {
+	klcpu_t		kc_cpu;
+	klhub_t		kc_hub;
+	klmembnk_t	kc_mem;
+	klxbow_t	kc_xbow;
+	klbri_t		kc_bri;
+	klioc3_t	kc_ioc3;
+	klvmeb_t	kc_vmeb;
+	klvmed_t	kc_vmed;
+	klrou_t		kc_rou;
+	klgfx_t		kc_gfx;
+	klscsi_t	kc_scsi;
+	klscdev_t	kc_scsi_dev;
+	klfddi_t	kc_fddi;
+	klmio_t		kc_mio;
+	klmod_serial_num_t kc_snum ;
+} klcomp_t;
+
+typedef union kldev_s {	     /* for device structure allocation */
+	klscdev_t	kc_scsi_dev ;
+	klttydev_t	kc_tty_dev ;
+	klenetdev_t	kc_enet_dev ;
+	klkbddev_t	kc_kbd_dev ;
+} kldev_t ;
+
+/* Data structure interface routines. TBD */
+
+/* Include launch info in this file itself? TBD */
+
+/*
+ * TBD - Can the ARCS and device driver related info also be included in the
+ * KLCONFIG area. On the IO4PROM, prom device driver info is part of cfgnode_t
+ * structure, viz private to the IO4prom.
+ */
+
+/*
+ * TBD - Allocation issues.
+ *
+ * Do we need to Mark off sepatate heaps for lboard_t, rboard_t, component,
+ * errinfo and allocate from them, or have a single heap and allocate all
+ * structures from it. Debug is easier in the former method since we can
+ * dump all similar structs in one command, but there will be lots of holes,
+ * in memory and max limits are needed for number of structures.
+ * Another way to make it organized, is to have a union of all components
+ * and allocate a aligned chunk of memory greater than the biggest
+ * component.
+ */
+
+typedef union {
+	lboard_t *lbinfo ;
+} biptr_t ;
+
+
+#define BRI_PER_XBOW 6
+#define PCI_PER_BRI  8
+#define DEV_PER_PCI  16
+
+
+/* Virtual dipswitch values (starting from switch "7"): */
+
+#define VDS_NOGFX		0x8000	/* Don't enable gfx and autoboot */
+#define VDS_NOMP		0x100	/* Don't start slave processors */
+#define VDS_MANUMODE		0x80	/* Manufacturing mode */
+#define VDS_NOARB		0x40	/* No bootmaster arbitration */
+#define VDS_PODMODE		0x20	/* Go straight to POD mode */
+#define VDS_NO_DIAGS		0x10	/* Don't run any diags after BM arb */
+#define VDS_DEFAULTS		0x08	/* Use default environment values */
+#define VDS_NOMEMCLEAR		0x04	/* Don't run mem cfg code */
+#define VDS_2ND_IO4		0x02	/* Boot from the second IO4 */
+#define VDS_DEBUG_PROM		0x01	/* Print PROM debugging messages */
+
+/* external declarations of Linux kernel functions. */
+
+extern lboard_t *find_lboard(lboard_t *start, unsigned char type);
+extern klinfo_t *find_component(lboard_t *brd, klinfo_t *kli, unsigned char type);
+extern klinfo_t *find_first_component(lboard_t *brd, unsigned char type);
+extern lboard_t *find_lboard_class(lboard_t *start, unsigned char brd_class);
+
+#endif /* _ASM_SN_KLCONFIG_H */
diff --git a/arch/mips/include/asm/sn/kldir.h b/arch/mips/include/asm/sn/kldir.h
new file mode 100644
index 000000000..245f59bf3
--- /dev/null
+++ b/arch/mips/include/asm/sn/kldir.h
@@ -0,0 +1,36 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifndef _ASM_SN_KLDIR_H
+#define _ASM_SN_KLDIR_H
+
+#define KLDIR_MAGIC		0x434d5f53505f5357
+
+#define KLDIR_OFF_MAGIC			0x00
+#define KLDIR_OFF_OFFSET		0x08
+#define KLDIR_OFF_POINTER		0x10
+#define KLDIR_OFF_SIZE			0x18
+#define KLDIR_OFF_COUNT			0x20
+#define KLDIR_OFF_STRIDE		0x28
+
+#define KLDIR_ENT_SIZE			0x40
+#define KLDIR_MAX_ENTRIES		(0x400 / 0x40)
+
+#ifndef __ASSEMBLY__
+typedef struct kldir_ent_s {
+	u64		magic;		/* Indicates validity of entry	    */
+	off_t		offset;		/* Offset from start of node space  */
+	unsigned long	pointer;	/* Pointer to area in some cases    */
+	size_t		size;		/* Size in bytes		    */
+	u64		count;		/* Repeat count if array, 1 if not  */
+	size_t		stride;		/* Stride if array, 0 if not	    */
+	char		rsvd[16];	/* Pad entry to 0x40 bytes	    */
+	/* NOTE: These 16 bytes are used in the Partition KLDIR
+	   entry to store partition info. Refer to klpart.h for this. */
+} kldir_ent_t;
+#endif /* !__ASSEMBLY__ */
+
+#ifdef CONFIG_SGI_IP27
+#include <asm/sn/sn0/kldir.h>
+#endif
+
+#endif /* _ASM_SN_KLDIR_H */
diff --git a/arch/mips/include/asm/sn/klkernvars.h b/arch/mips/include/asm/sn/klkernvars.h
new file mode 100644
index 000000000..ea6b21795
--- /dev/null
+++ b/arch/mips/include/asm/sn/klkernvars.h
@@ -0,0 +1,29 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * File ported from IRIX to Linux by Kanoj Sarcar, 06/08/00.
+ * Copyright 2000 Silicon Graphics, Inc.
+ */
+#ifndef __ASM_SN_KLKERNVARS_H
+#define __ASM_SN_KLKERNVARS_H
+
+#define KV_MAGIC_OFFSET		0x0
+#define KV_RO_NASID_OFFSET	0x4
+#define KV_RW_NASID_OFFSET	0x6
+
+#define KV_MAGIC		0x5f4b565f
+
+#ifndef __ASSEMBLY__
+
+#include <asm/sn/types.h>
+
+typedef struct kern_vars_s {
+	int		kv_magic;
+	nasid_t		kv_ro_nasid;
+	nasid_t		kv_rw_nasid;
+	unsigned long	kv_ro_baseaddr;
+	unsigned long	kv_rw_baseaddr;
+} kern_vars_t;
+
+#endif /* !__ASSEMBLY__ */
+
+#endif /* __ASM_SN_KLKERNVARS_H */
diff --git a/arch/mips/include/asm/sn/launch.h b/arch/mips/include/asm/sn/launch.h
new file mode 100644
index 000000000..04226d8d3
--- /dev/null
+++ b/arch/mips/include/asm/sn/launch.h
@@ -0,0 +1,106 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1992 - 1997, 2000 Silicon Graphics, Inc.
+ * Copyright (C) 2000 by Colin Ngam
+ */
+#ifndef _ASM_SN_LAUNCH_H
+#define _ASM_SN_LAUNCH_H
+
+#include <asm/sn/types.h>
+#include <asm/sn/addrs.h>
+
+/*
+ * The launch data structure resides at a fixed place in each node's memory
+ * and is used to communicate between the master processor and the slave
+ * processors.
+ *
+ * The master stores launch parameters in the launch structure
+ * corresponding to a target processor that is in a slave loop, then sends
+ * an interrupt to the slave processor.	 The slave calls the desired
+ * function, then returns to the slave loop.  The master may poll or wait
+ * for the slaves to finish.
+ *
+ * There is an array of launch structures, one per CPU on the node.  One
+ * interrupt level is used per local CPU.
+ */
+
+#define LAUNCH_MAGIC		0xaddbead2addbead3
+#ifdef CONFIG_SGI_IP27
+#define LAUNCH_SIZEOF		0x100
+#define LAUNCH_PADSZ		0xa0
+#endif
+
+#define LAUNCH_OFF_MAGIC	0x00	/* Struct offsets for assembly	    */
+#define LAUNCH_OFF_BUSY		0x08
+#define LAUNCH_OFF_CALL		0x10
+#define LAUNCH_OFF_CALLC	0x18
+#define LAUNCH_OFF_CALLPARM	0x20
+#define LAUNCH_OFF_STACK	0x28
+#define LAUNCH_OFF_GP		0x30
+#define LAUNCH_OFF_BEVUTLB	0x38
+#define LAUNCH_OFF_BEVNORMAL	0x40
+#define LAUNCH_OFF_BEVECC	0x48
+
+#define LAUNCH_STATE_DONE	0	/* Return value of LAUNCH_POLL	    */
+#define LAUNCH_STATE_SENT	1
+#define LAUNCH_STATE_RECD	2
+
+/*
+ * The launch routine is called only if the complement address is correct.
+ *
+ * Before control is transferred to a routine, the complement address
+ * is zeroed (invalidated) to prevent an accidental call from a spurious
+ * interrupt.
+ *
+ * The slave_launch routine turns on the BUSY flag, and the slave loop
+ * clears the BUSY flag after control is returned to it.
+ */
+
+#ifndef __ASSEMBLY__
+
+typedef int launch_state_t;
+typedef void (*launch_proc_t)(u64 call_parm);
+
+typedef struct launch_s {
+	volatile u64		magic;	/* Magic number			    */
+	volatile u64		busy;	/* Slave currently active	    */
+	volatile launch_proc_t	call_addr;	/* Func. for slave to call  */
+	volatile u64		call_addr_c;	/* 1's complement of call_addr*/
+	volatile u64		call_parm;	/* Single parm passed to call*/
+	volatile void *stack_addr;	/* Stack pointer for slave function */
+	volatile void *gp_addr;		/* Global pointer for slave func.   */
+	volatile char		*bevutlb;/* Address of bev utlb ex handler   */
+	volatile char		*bevnormal;/*Address of bev normal ex handler */
+	volatile char		*bevecc;/* Address of bev cache err handler */
+	volatile char		pad[160];	/* Pad to LAUNCH_SIZEOF	    */
+} launch_t;
+
+/*
+ * PROM entry points for launch routines are determined by IPxxprom/start.s
+ */
+
+#define LAUNCH_SLAVE	(*(void (*)(int nasid, int cpu, \
+				    launch_proc_t call_addr, \
+				    u64 call_parm, \
+				    void *stack_addr, \
+				    void *gp_addr)) \
+			 IP27PROM_LAUNCHSLAVE)
+
+#define LAUNCH_WAIT	(*(void (*)(int nasid, int cpu, int timeout_msec)) \
+			 IP27PROM_WAITSLAVE)
+
+#define LAUNCH_POLL	(*(launch_state_t (*)(int nasid, int cpu)) \
+			 IP27PROM_POLLSLAVE)
+
+#define LAUNCH_LOOP	(*(void (*)(void)) \
+			 IP27PROM_SLAVELOOP)
+
+#define LAUNCH_FLASH	(*(void (*)(void)) \
+			 IP27PROM_FLASHLEDS)
+
+#endif /* !__ASSEMBLY__ */
+
+#endif /* _ASM_SN_LAUNCH_H */
diff --git a/arch/mips/include/asm/sn/mapped_kernel.h b/arch/mips/include/asm/sn/mapped_kernel.h
new file mode 100644
index 000000000..3f1049807
--- /dev/null
+++ b/arch/mips/include/asm/sn/mapped_kernel.h
@@ -0,0 +1,55 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * File created by Kanoj Sarcar 06/06/00.
+ * Copyright 2000 Silicon Graphics, Inc.
+ */
+#ifndef __ASM_SN_MAPPED_KERNEL_H
+#define __ASM_SN_MAPPED_KERNEL_H
+
+#include <linux/mmzone.h>
+
+/*
+ * Note on how mapped kernels work: the text and data section is
+ * compiled at cksseg segment (LOADADDR = 0xc001c000), and the
+ * init/setup/data section gets a 16M virtual address bump in the
+ * ld.script file (so that tlblo0 and tlblo1 maps the sections).
+ * The vmlinux.64 section addresses are put in the xkseg range
+ * using the change-addresses makefile option. Use elfdump -of
+ * on IRIX to see where the sections go. The Origin loader loads
+ * the two sections contiguously in physical memory. The loader
+ * sets the entry point into kernel_entry using a xkphys address,
+ * but instead of using 0xa800000001160000, it uses the address
+ * 0xa800000000160000, which is where it physically loaded that
+ * code. So no jumps can be done before we have switched to using
+ * cksseg addresses.
+ */
+#include <asm/addrspace.h>
+
+#define REP_BASE	CAC_BASE
+
+#ifdef CONFIG_MAPPED_KERNEL
+
+#define MAPPED_ADDR_RO_TO_PHYS(x)	(x - REP_BASE)
+#define MAPPED_ADDR_RW_TO_PHYS(x)	(x - REP_BASE - 16777216)
+
+#define MAPPED_KERN_RO_PHYSBASE(n) (hub_data(n)->kern_vars.kv_ro_baseaddr)
+#define MAPPED_KERN_RW_PHYSBASE(n) (hub_data(n)->kern_vars.kv_rw_baseaddr)
+
+#define MAPPED_KERN_RO_TO_PHYS(x) \
+				((unsigned long)MAPPED_ADDR_RO_TO_PHYS(x) | \
+				MAPPED_KERN_RO_PHYSBASE(get_nasid()))
+#define MAPPED_KERN_RW_TO_PHYS(x) \
+				((unsigned long)MAPPED_ADDR_RW_TO_PHYS(x) | \
+				MAPPED_KERN_RW_PHYSBASE(get_nasid()))
+
+#else /* CONFIG_MAPPED_KERNEL */
+
+#define MAPPED_KERN_RO_TO_PHYS(x)	(x - REP_BASE)
+#define MAPPED_KERN_RW_TO_PHYS(x)	(x - REP_BASE)
+
+#endif /* CONFIG_MAPPED_KERNEL */
+
+#define MAPPED_KERN_RO_TO_K0(x) PHYS_TO_K0(MAPPED_KERN_RO_TO_PHYS(x))
+#define MAPPED_KERN_RW_TO_K0(x) PHYS_TO_K0(MAPPED_KERN_RW_TO_PHYS(x))
+
+#endif /* __ASM_SN_MAPPED_KERNEL_H  */
diff --git a/arch/mips/include/asm/sn/nmi.h b/arch/mips/include/asm/sn/nmi.h
new file mode 100644
index 000000000..12ac210f1
--- /dev/null
+++ b/arch/mips/include/asm/sn/nmi.h
@@ -0,0 +1,125 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Derived from IRIX <sys/SN/nmi.h>, Revision 1.5.
+ *
+ * Copyright (C) 1992 - 1997 Silicon Graphics, Inc.
+ */
+#ifndef __ASM_SN_NMI_H
+#define __ASM_SN_NMI_H
+
+#include <asm/sn/addrs.h>
+
+/*
+ * The launch data structure resides at a fixed place in each node's memory
+ * and is used to communicate between the master processor and the slave
+ * processors.
+ *
+ * The master stores launch parameters in the launch structure
+ * corresponding to a target processor that is in a slave loop, then sends
+ * an interrupt to the slave processor.	 The slave calls the desired
+ * function, followed by an optional rendezvous function, then returns to
+ * the slave loop.  The master does not wait for the slaves before
+ * returning.
+ *
+ * There is an array of launch structures, one per CPU on the node.  One
+ * interrupt level is used per CPU.
+ */
+
+#define NMI_MAGIC		0x48414d4d455201
+#define NMI_SIZEOF		0x40
+
+#define NMI_OFF_MAGIC		0x00	/* Struct offsets for assembly	    */
+#define NMI_OFF_FLAGS		0x08
+#define NMI_OFF_CALL		0x10
+#define NMI_OFF_CALLC		0x18
+#define NMI_OFF_CALLPARM	0x20
+#define NMI_OFF_GMASTER		0x28
+
+/*
+ * The NMI routine is called only if the complement address is
+ * correct.
+ *
+ * Before control is transferred to a routine, the complement address
+ * is zeroed (invalidated) to prevent an accidental call from a spurious
+ * interrupt.
+ *
+ */
+
+#ifndef __ASSEMBLY__
+
+typedef struct nmi_s {
+	volatile unsigned long	 magic;		/* Magic number */
+	volatile unsigned long	 flags;		/* Combination of flags above */
+	volatile void *call_addr;	/* Routine for slave to call	    */
+	volatile void *call_addr_c;	/* 1's complement of address	    */
+	volatile void *call_parm;	/* Single parm passed to call	    */
+	volatile unsigned long	 gmaster;	/* Flag true only on global master*/
+} nmi_t;
+
+#endif /* !__ASSEMBLY__ */
+
+/* Following definitions are needed both in the prom & the kernel
+ * to identify the format of the nmi cpu register save area in the
+ * low memory on each node.
+ */
+#ifndef __ASSEMBLY__
+
+struct reg_struct {
+	unsigned long	gpr[32];
+	unsigned long	sr;
+	unsigned long	cause;
+	unsigned long	epc;
+	unsigned long	badva;
+	unsigned long	error_epc;
+	unsigned long	cache_err;
+	unsigned long	nmi_sr;
+};
+
+#endif /* !__ASSEMBLY__ */
+
+/* These are the assembly language offsets into the reg_struct structure */
+
+#define R0_OFF		0x0
+#define R1_OFF		0x8
+#define R2_OFF		0x10
+#define R3_OFF		0x18
+#define R4_OFF		0x20
+#define R5_OFF		0x28
+#define R6_OFF		0x30
+#define R7_OFF		0x38
+#define R8_OFF		0x40
+#define R9_OFF		0x48
+#define R10_OFF		0x50
+#define R11_OFF		0x58
+#define R12_OFF		0x60
+#define R13_OFF		0x68
+#define R14_OFF		0x70
+#define R15_OFF		0x78
+#define R16_OFF		0x80
+#define R17_OFF		0x88
+#define R18_OFF		0x90
+#define R19_OFF		0x98
+#define R20_OFF		0xa0
+#define R21_OFF		0xa8
+#define R22_OFF		0xb0
+#define R23_OFF		0xb8
+#define R24_OFF		0xc0
+#define R25_OFF		0xc8
+#define R26_OFF		0xd0
+#define R27_OFF		0xd8
+#define R28_OFF		0xe0
+#define R29_OFF		0xe8
+#define R30_OFF		0xf0
+#define R31_OFF		0xf8
+#define SR_OFF		0x100
+#define CAUSE_OFF	0x108
+#define EPC_OFF		0x110
+#define BADVA_OFF	0x118
+#define ERROR_EPC_OFF	0x120
+#define CACHE_ERR_OFF	0x128
+#define NMISR_OFF	0x130
+
+#endif /* __ASM_SN_NMI_H */
diff --git a/arch/mips/include/asm/sn/sn0/addrs.h b/arch/mips/include/asm/sn/sn0/addrs.h
new file mode 100644
index 000000000..f13df84ed
--- /dev/null
+++ b/arch/mips/include/asm/sn/sn0/addrs.h
@@ -0,0 +1,283 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Derived from IRIX <sys/SN/SN0/addrs.h>, revision 1.126.
+ *
+ * Copyright (C) 1992 - 1997, 1999 Silicon Graphics, Inc.
+ * Copyright (C) 1999 by Ralf Baechle
+ */
+#ifndef _ASM_SN_SN0_ADDRS_H
+#define _ASM_SN_SN0_ADDRS_H
+
+
+/*
+ * SN0 (on a T5) Address map
+ *
+ * This file contains a set of definitions and macros which are used
+ * to reference into the major address spaces (CAC, HSPEC, IO, MSPEC,
+ * and UNCAC) used by the SN0 architecture.  It also contains addresses
+ * for "major" statically locatable PROM/Kernel data structures, such as
+ * the partition table, the configuration data structure, etc.
+ * We make an implicit assumption that the processor using this file
+ * follows the R10K's provisions for specifying uncached attributes;
+ * should this change, the base registers may very well become processor-
+ * dependent.
+ *
+ * For more information on the address spaces, see the "Local Resources"
+ * chapter of the Hub specification.
+ *
+ * NOTE: This header file is included both by C and by assembler source
+ *	 files.	 Please bracket any language-dependent definitions
+ *	 appropriately.
+ */
+
+/*
+ * Some of the macros here need to be casted to appropriate types when used
+ * from C.  They definitely must not be casted from assembly language so we
+ * use some new ANSI preprocessor stuff to paste these on where needed.
+ */
+
+/*
+ * The following couple of definitions will eventually need to be variables,
+ * since the amount of address space assigned to each node depends on
+ * whether the system is running in N-mode (more nodes with less memory)
+ * or M-mode (fewer nodes with more memory).  We expect that it will
+ * be a while before we need to make this decision dynamically, though,
+ * so for now we just use defines bracketed by an ifdef.
+ */
+
+#ifdef CONFIG_SGI_SN_N_MODE
+
+#define NODE_SIZE_BITS		31
+#define BWIN_SIZE_BITS		28
+
+#define NASID_BITS		9
+#define NASID_BITMASK		(0x1ffLL)
+#define NASID_SHFT		31
+#define NASID_META_BITS		5
+#define NASID_LOCAL_BITS	4
+
+#define BDDIR_UPPER_MASK	(UINT64_CAST 0x7ffff << 10)
+#define BDECC_UPPER_MASK	(UINT64_CAST 0x3ffffff << 3)
+
+#else /* !defined(CONFIG_SGI_SN_N_MODE), assume that M-mode is desired */
+
+#define NODE_SIZE_BITS		32
+#define BWIN_SIZE_BITS		29
+
+#define NASID_BITMASK		(0xffLL)
+#define NASID_BITS		8
+#define NASID_SHFT		32
+#define NASID_META_BITS		4
+#define NASID_LOCAL_BITS	4
+
+#define BDDIR_UPPER_MASK	(UINT64_CAST 0xfffff << 10)
+#define BDECC_UPPER_MASK	(UINT64_CAST 0x7ffffff << 3)
+
+#endif /* !defined(CONFIG_SGI_SN_N_MODE) */
+
+#define NODE_ADDRSPACE_SIZE	(UINT64_CAST 1 << NODE_SIZE_BITS)
+
+#define NASID_MASK		(UINT64_CAST NASID_BITMASK << NASID_SHFT)
+#define NASID_GET(_pa)		(int) ((UINT64_CAST (_pa) >>		\
+					NASID_SHFT) & NASID_BITMASK)
+
+#if !defined(__ASSEMBLY__)
+
+#define NODE_SWIN_BASE(nasid, widget)					\
+	((widget == 0) ? NODE_BWIN_BASE((nasid), SWIN0_BIGWIN)		\
+	: RAW_NODE_SWIN_BASE(nasid, widget))
+#else /* __ASSEMBLY__ */
+#define NODE_SWIN_BASE(nasid, widget) \
+     (NODE_IO_BASE(nasid) + (UINT64_CAST(widget) << SWIN_SIZE_BITS))
+#endif /* __ASSEMBLY__ */
+
+/*
+ * The following definitions pertain to the IO special address
+ * space.  They define the location of the big and little windows
+ * of any given node.
+ */
+
+#define BWIN_INDEX_BITS		3
+#define BWIN_SIZE		(UINT64_CAST 1 << BWIN_SIZE_BITS)
+#define BWIN_SIZEMASK		(BWIN_SIZE - 1)
+#define BWIN_WIDGET_MASK	0x7
+#define NODE_BWIN_BASE0(nasid)	(NODE_IO_BASE(nasid) + BWIN_SIZE)
+#define NODE_BWIN_BASE(nasid, bigwin)	(NODE_BWIN_BASE0(nasid) +	\
+			(UINT64_CAST(bigwin) << BWIN_SIZE_BITS))
+
+#define BWIN_WIDGETADDR(addr)	((addr) & BWIN_SIZEMASK)
+#define BWIN_WINDOWNUM(addr)	(((addr) >> BWIN_SIZE_BITS) & BWIN_WIDGET_MASK)
+/*
+ * Verify if addr belongs to large window address of node with "nasid"
+ *
+ *
+ * NOTE: "addr" is expected to be XKPHYS address, and NOT physical
+ * address
+ *
+ *
+ */
+
+#define NODE_BWIN_ADDR(nasid, addr)	\
+		(((addr) >= NODE_BWIN_BASE0(nasid)) && \
+		 ((addr) < (NODE_BWIN_BASE(nasid, HUB_NUM_BIG_WINDOW) + \
+				BWIN_SIZE)))
+
+/*
+ * The following define the major position-independent aliases used
+ * in SN0.
+ *	CALIAS -- Varies in size, points to the first n bytes of memory
+ *			on the reader's node.
+ */
+
+#define CALIAS_BASE		CAC_BASE
+
+#define SN0_WIDGET_BASE(_nasid, _wid)	(NODE_SWIN_BASE((_nasid), (_wid)))
+
+/* Turn on sable logging for the processors whose bits are set. */
+#define SABLE_LOG_TRIGGER(_map)
+
+#ifndef __ASSEMBLY__
+#define KERN_NMI_ADDR(nasid, slice)					\
+		    TO_NODE_UNCAC((nasid), IP27_NMI_KREGS_OFFSET +	\
+				  (IP27_NMI_KREGS_CPU_SIZE * (slice)))
+#endif /* !__ASSEMBLY__ */
+
+#ifdef PROM
+
+#define MISC_PROM_BASE		PHYS_TO_K0(0x01300000)
+#define MISC_PROM_SIZE		0x200000
+
+#define DIAG_BASE		PHYS_TO_K0(0x01500000)
+#define DIAG_SIZE		0x300000
+
+#define ROUTE_BASE		PHYS_TO_K0(0x01800000)
+#define ROUTE_SIZE		0x200000
+
+#define IP27PROM_FLASH_HDR	PHYS_TO_K0(0x01300000)
+#define IP27PROM_FLASH_DATA	PHYS_TO_K0(0x01301000)
+#define IP27PROM_CORP_MAX	32
+#define IP27PROM_CORP		PHYS_TO_K0(0x01800000)
+#define IP27PROM_CORP_SIZE	0x10000
+#define IP27PROM_CORP_STK	PHYS_TO_K0(0x01810000)
+#define IP27PROM_CORP_STKSIZE	0x2000
+#define IP27PROM_DECOMP_BUF	PHYS_TO_K0(0x01900000)
+#define IP27PROM_DECOMP_SIZE	0xfff00
+
+#define IP27PROM_BASE		PHYS_TO_K0(0x01a00000)
+#define IP27PROM_BASE_MAPPED	(UNCAC_BASE | 0x1fc00000)
+#define IP27PROM_SIZE_MAX	0x100000
+
+#define IP27PROM_PCFG		PHYS_TO_K0(0x01b00000)
+#define IP27PROM_PCFG_SIZE	0xd0000
+#define IP27PROM_ERRDMP		PHYS_TO_K1(0x01bd0000)
+#define IP27PROM_ERRDMP_SIZE	0xf000
+
+#define IP27PROM_INIT_START	PHYS_TO_K1(0x01bd0000)
+#define IP27PROM_CONSOLE	PHYS_TO_K1(0x01bdf000)
+#define IP27PROM_CONSOLE_SIZE	0x200
+#define IP27PROM_NETUART	PHYS_TO_K1(0x01bdf200)
+#define IP27PROM_NETUART_SIZE	0x100
+#define IP27PROM_UNUSED1	PHYS_TO_K1(0x01bdf300)
+#define IP27PROM_UNUSED1_SIZE	0x500
+#define IP27PROM_ELSC_BASE_A	PHYS_TO_K0(0x01bdf800)
+#define IP27PROM_ELSC_BASE_B	PHYS_TO_K0(0x01bdfc00)
+#define IP27PROM_STACK_A	PHYS_TO_K0(0x01be0000)
+#define IP27PROM_STACK_B	PHYS_TO_K0(0x01bf0000)
+#define IP27PROM_STACK_SHFT	16
+#define IP27PROM_STACK_SIZE	(1 << IP27PROM_STACK_SHFT)
+#define IP27PROM_INIT_END	PHYS_TO_K0(0x01c00000)
+
+#define SLAVESTACK_BASE		PHYS_TO_K0(0x01580000)
+#define SLAVESTACK_SIZE		0x40000
+
+#define ENETBUFS_BASE		PHYS_TO_K0(0x01f80000)
+#define ENETBUFS_SIZE		0x20000
+
+#define IO6PROM_BASE		PHYS_TO_K0(0x01c00000)
+#define IO6PROM_SIZE		0x400000
+#define IO6PROM_BASE_MAPPED	(UNCAC_BASE | 0x11c00000)
+#define IO6DPROM_BASE		PHYS_TO_K0(0x01c00000)
+#define IO6DPROM_SIZE		0x200000
+
+#define NODEBUGUNIX_ADDR	PHYS_TO_K0(0x00019000)
+#define DEBUGUNIX_ADDR		PHYS_TO_K0(0x00100000)
+
+#define IP27PROM_INT_LAUNCH	10	/* and 11 */
+#define IP27PROM_INT_NETUART	12	/* through 17 */
+
+#endif /* PROM */
+
+/*
+ * needed by symmon so it needs to be outside #if PROM
+ */
+#define IP27PROM_ELSC_SHFT	10
+#define IP27PROM_ELSC_SIZE	(1 << IP27PROM_ELSC_SHFT)
+
+/*
+ * This address is used by IO6PROM to build MemoryDescriptors of
+ * free memory. This address is important since unix gets loaded
+ * at this address, and this memory has to be FREE if unix is to
+ * be loaded.
+ */
+
+#define FREEMEM_BASE		PHYS_TO_K0(0x2000000)
+
+#define IO6PROM_STACK_SHFT	14	/* stack per cpu */
+#define IO6PROM_STACK_SIZE	(1 << IO6PROM_STACK_SHFT)
+
+/*
+ * IP27 PROM vectors
+ */
+
+#define IP27PROM_ENTRY		PHYS_TO_COMPATK1(0x1fc00000)
+#define IP27PROM_RESTART	PHYS_TO_COMPATK1(0x1fc00008)
+#define IP27PROM_SLAVELOOP	PHYS_TO_COMPATK1(0x1fc00010)
+#define IP27PROM_PODMODE	PHYS_TO_COMPATK1(0x1fc00018)
+#define IP27PROM_IOC3UARTPOD	PHYS_TO_COMPATK1(0x1fc00020)
+#define IP27PROM_FLASHLEDS	PHYS_TO_COMPATK1(0x1fc00028)
+#define IP27PROM_REPOD		PHYS_TO_COMPATK1(0x1fc00030)
+#define IP27PROM_LAUNCHSLAVE	PHYS_TO_COMPATK1(0x1fc00038)
+#define IP27PROM_WAITSLAVE	PHYS_TO_COMPATK1(0x1fc00040)
+#define IP27PROM_POLLSLAVE	PHYS_TO_COMPATK1(0x1fc00048)
+
+#define KL_UART_BASE	LOCAL_HUB_ADDR(MD_UREG0_0)	/* base of UART regs */
+#define KL_UART_CMD	LOCAL_HUB_ADDR(MD_UREG0_0)	/* UART command reg */
+#define KL_UART_DATA	LOCAL_HUB_ADDR(MD_UREG0_1)	/* UART data reg */
+#define KL_I2C_REG	MD_UREG0_0			/* I2C reg */
+
+#ifndef __ASSEMBLY__
+
+/* Address 0x400 to 0x1000 ualias points to cache error eframe + misc
+ * CACHE_ERR_SP_PTR could either contain an address to the stack, or
+ * the stack could start at CACHE_ERR_SP_PTR
+ */
+#if defined(HUB_ERR_STS_WAR)
+#define CACHE_ERR_EFRAME	0x480
+#else /* HUB_ERR_STS_WAR */
+#define CACHE_ERR_EFRAME	0x400
+#endif /* HUB_ERR_STS_WAR */
+
+#define CACHE_ERR_ECCFRAME	(CACHE_ERR_EFRAME + EF_SIZE)
+#define CACHE_ERR_SP_PTR	(0x1000 - 32)	/* why -32? TBD */
+#define CACHE_ERR_IBASE_PTR	(0x1000 - 40)
+#define CACHE_ERR_SP		(CACHE_ERR_SP_PTR - 16)
+#define CACHE_ERR_AREA_SIZE	(ARCS_SPB_OFFSET - CACHE_ERR_EFRAME)
+
+#endif	/* !__ASSEMBLY__ */
+
+#define _ARCSPROM
+
+#if defined(HUB_ERR_STS_WAR)
+
+#define ERR_STS_WAR_REGISTER	IIO_IIBUSERR
+#define ERR_STS_WAR_ADDR	LOCAL_HUB_ADDR(IIO_IIBUSERR)
+#define ERR_STS_WAR_PHYSADDR	TO_PHYS((__psunsigned_t)ERR_STS_WAR_ADDR)
+				/* Used to match addr in error reg. */
+#define OLD_ERR_STS_WAR_OFFSET	((MD_MEM_BANKS * MD_BANK_SIZE) - 0x100)
+
+#endif /* HUB_ERR_STS_WAR */
+
+#endif /* _ASM_SN_SN0_ADDRS_H */
diff --git a/arch/mips/include/asm/sn/sn0/arch.h b/arch/mips/include/asm/sn/sn0/arch.h
new file mode 100644
index 000000000..12f4c4649
--- /dev/null
+++ b/arch/mips/include/asm/sn/sn0/arch.h
@@ -0,0 +1,56 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * SGI IP27 specific setup.
+ *
+ * Copyright (C) 1995 - 1997, 1999 Silcon Graphics, Inc.
+ * Copyright (C) 1999 Ralf Baechle (ralf@gnu.org)
+ */
+#ifndef _ASM_SN_SN0_ARCH_H
+#define _ASM_SN_SN0_ARCH_H
+
+
+/*
+ * MAXCPUS refers to the maximum number of CPUs in a single kernel.
+ * This is not necessarily the same as MAXNODES * CPUS_PER_NODE
+ */
+#define MAXCPUS			(MAX_NUMNODES * CPUS_PER_NODE)
+
+/*
+ * This is the maximum number of NASIDS that can be present in a system.
+ * (Highest NASID plus one.)
+ */
+#define MAX_NASIDS		256
+
+/*
+ * MAX_REGIONS refers to the maximum number of hardware partitioned regions.
+ */
+#define MAX_REGIONS		64
+#define MAX_NONPREMIUM_REGIONS	16
+#define MAX_PREMIUM_REGIONS	MAX_REGIONS
+
+/*
+ * MAX_PARITIONS refers to the maximum number of logically defined
+ * partitions the system can support.
+ */
+#define MAX_PARTITIONS		MAX_REGIONS
+
+#define NASID_MASK_BYTES	((MAX_NASIDS + 7) / 8)
+
+/*
+ * Slot constants for SN0
+ */
+#ifdef CONFIG_SGI_SN_N_MODE
+#define MAX_MEM_SLOTS	16			/* max slots per node */
+#else /* !CONFIG_SGI_SN_N_MODE, assume CONFIG_SGI_SN_M_MODE */
+#define MAX_MEM_SLOTS	32			/* max slots per node */
+#endif /* CONFIG_SGI_SN_M_MODE */
+
+#define SLOT_SHIFT		(27)
+#define SLOT_MIN_MEM_SIZE	(32*1024*1024)
+
+#define CPUS_PER_NODE		2	/* CPUs on a single hub */
+
+#endif /* _ASM_SN_SN0_ARCH_H */
diff --git a/arch/mips/include/asm/sn/sn0/hub.h b/arch/mips/include/asm/sn/sn0/hub.h
new file mode 100644
index 000000000..c84adde36
--- /dev/null
+++ b/arch/mips/include/asm/sn/sn0/hub.h
@@ -0,0 +1,62 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1992 - 1997, 1999 Silicon Graphics, Inc.
+ * Copyright (C) 1999 by Ralf Baechle
+ */
+#ifndef _ASM_SN_SN0_HUB_H
+#define _ASM_SN_SN0_HUB_H
+
+/* The secret password; used to release protection */
+#define HUB_PASSWORD		0x53474972756c6573ull
+
+#define CHIPID_HUB		0
+#define CHIPID_ROUTER		1
+
+#define HUB_REV_1_0		1
+#define HUB_REV_2_0		2
+#define HUB_REV_2_1		3
+#define HUB_REV_2_2		4
+#define HUB_REV_2_3		5
+#define HUB_REV_2_4		6
+
+#define MAX_HUB_PATH		80
+
+#include <asm/sn/sn0/addrs.h>
+#include <asm/sn/sn0/hubpi.h>
+#include <asm/sn/sn0/hubmd.h>
+#include <asm/sn/sn0/hubio.h>
+#include <asm/sn/sn0/hubni.h>
+//#include <asm/sn/sn0/hubcore.h>
+
+/* Translation of uncached attributes */
+#define UATTR_HSPEC	0
+#define UATTR_IO	1
+#define UATTR_MSPEC	2
+#define UATTR_UNCAC	3
+
+#ifdef __ASSEMBLY__
+/*
+ * Returns the local nasid into res.
+ */
+	.macro GET_NASID_ASM res
+	dli	\res, LOCAL_HUB_ADDR(NI_STATUS_REV_ID)
+	ld	\res, (\res)
+	and	\res, NSRI_NODEID_MASK
+	dsrl	\res, NSRI_NODEID_SHFT
+	.endm
+#else
+
+/*
+ * get_nasid() returns the physical node id number of the caller.
+ */
+static inline nasid_t get_nasid(void)
+{
+	return (nasid_t)((LOCAL_HUB_L(NI_STATUS_REV_ID) & NSRI_NODEID_MASK)
+			 >> NSRI_NODEID_SHFT);
+}
+#endif
+
+#endif /* _ASM_SN_SN0_HUB_H */
diff --git a/arch/mips/include/asm/sn/sn0/hubio.h b/arch/mips/include/asm/sn/sn0/hubio.h
new file mode 100644
index 000000000..57ece90f8
--- /dev/null
+++ b/arch/mips/include/asm/sn/sn0/hubio.h
@@ -0,0 +1,972 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Derived from IRIX <sys/SN/SN0/hubio.h>, Revision 1.80.
+ *
+ * Copyright (C) 1992 - 1997, 1999 Silicon Graphics, Inc.
+ * Copyright (C) 1999 by Ralf Baechle
+ */
+#ifndef _ASM_SGI_SN_SN0_HUBIO_H
+#define _ASM_SGI_SN_SN0_HUBIO_H
+
+/*
+ * Hub I/O interface registers
+ *
+ * All registers in this file are subject to change until Hub chip tapeout.
+ * In general, the longer software name should be used when available.
+ */
+
+/*
+ * Slightly friendlier names for some common registers.
+ * The hardware definitions follow.
+ */
+#define IIO_WIDGET		IIO_WID	     /* Widget identification */
+#define IIO_WIDGET_STAT		IIO_WSTAT    /* Widget status register */
+#define IIO_WIDGET_CTRL		IIO_WCR	     /* Widget control register */
+#define IIO_WIDGET_TOUT		IIO_WRTO     /* Widget request timeout */
+#define IIO_WIDGET_FLUSH	IIO_WTFR     /* Widget target flush */
+#define IIO_PROTECT		IIO_ILAPR    /* IO interface protection */
+#define IIO_PROTECT_OVRRD	IIO_ILAPO    /* IO protect override */
+#define IIO_OUTWIDGET_ACCESS	IIO_IOWA     /* Outbound widget access */
+#define IIO_INWIDGET_ACCESS	IIO_IIWA     /* Inbound widget access */
+#define IIO_INDEV_ERR_MASK	IIO_IIDEM    /* Inbound device error mask */
+#define IIO_LLP_CSR		IIO_ILCSR    /* LLP control and status */
+#define IIO_LLP_LOG		IIO_ILLR     /* LLP log */
+#define IIO_XTALKCC_TOUT	IIO_IXCC     /* Xtalk credit count timeout*/
+#define IIO_XTALKTT_TOUT	IIO_IXTT     /* Xtalk tail timeout */
+#define IIO_IO_ERR_CLR		IIO_IECLR    /* IO error clear */
+#define IIO_BTE_CRB_CNT		IIO_IBCN     /* IO BTE CRB count */
+
+#define IIO_LLP_CSR_IS_UP		0x00002000
+#define IIO_LLP_CSR_LLP_STAT_MASK	0x00003000
+#define IIO_LLP_CSR_LLP_STAT_SHFT	12
+
+/* key to IIO_PROTECT_OVRRD */
+#define IIO_PROTECT_OVRRD_KEY	0x53474972756c6573ull	/* "SGIrules" */
+
+/* BTE register names */
+#define IIO_BTE_STAT_0		IIO_IBLS_0   /* Also BTE length/status 0 */
+#define IIO_BTE_SRC_0		IIO_IBSA_0   /* Also BTE source address	 0 */
+#define IIO_BTE_DEST_0		IIO_IBDA_0   /* Also BTE dest. address 0 */
+#define IIO_BTE_CTRL_0		IIO_IBCT_0   /* Also BTE control/terminate 0 */
+#define IIO_BTE_NOTIFY_0	IIO_IBNA_0   /* Also BTE notification 0 */
+#define IIO_BTE_INT_0		IIO_IBIA_0   /* Also BTE interrupt 0 */
+#define IIO_BTE_OFF_0		0	     /* Base offset from BTE 0 regs. */
+#define IIO_BTE_OFF_1	IIO_IBLS_1 - IIO_IBLS_0 /* Offset from base to BTE 1 */
+
+/* BTE register offsets from base */
+#define BTEOFF_STAT		0
+#define BTEOFF_SRC		(IIO_BTE_SRC_0 - IIO_BTE_STAT_0)
+#define BTEOFF_DEST		(IIO_BTE_DEST_0 - IIO_BTE_STAT_0)
+#define BTEOFF_CTRL		(IIO_BTE_CTRL_0 - IIO_BTE_STAT_0)
+#define BTEOFF_NOTIFY		(IIO_BTE_NOTIFY_0 - IIO_BTE_STAT_0)
+#define BTEOFF_INT		(IIO_BTE_INT_0 - IIO_BTE_STAT_0)
+
+
+/*
+ * The following definitions use the names defined in the IO interface
+ * document for ease of reference.  When possible, software should
+ * generally use the longer but clearer names defined above.
+ */
+
+#define IIO_BASE	0x400000
+#define IIO_BASE_BTE0	0x410000
+#define IIO_BASE_BTE1	0x420000
+#define IIO_BASE_PERF	0x430000
+#define IIO_PERF_CNT	0x430008
+
+#define IO_PERF_SETS	32
+
+#define IIO_WID		0x400000	/* Widget identification */
+#define IIO_WSTAT	0x400008	/* Widget status */
+#define IIO_WCR		0x400020	/* Widget control */
+
+#define IIO_WSTAT_ECRAZY	(1ULL << 32)	/* Hub gone crazy */
+#define IIO_WSTAT_TXRETRY	(1ULL << 9)	/* Hub Tx Retry timeout */
+#define IIO_WSTAT_TXRETRY_MASK	(0x7F)
+#define IIO_WSTAT_TXRETRY_SHFT	(16)
+#define IIO_WSTAT_TXRETRY_CNT(w)	(((w) >> IIO_WSTAT_TXRETRY_SHFT) & \
+					  IIO_WSTAT_TXRETRY_MASK)
+
+#define IIO_ILAPR	0x400100	/* Local Access Protection */
+#define IIO_ILAPO	0x400108	/* Protection override */
+#define IIO_IOWA	0x400110	/* outbound widget access */
+#define IIO_IIWA	0x400118	/* inbound widget access */
+#define IIO_IIDEM	0x400120	/* Inbound Device Error Mask */
+#define IIO_ILCSR	0x400128	/* LLP control and status */
+#define IIO_ILLR	0x400130	/* LLP Log */
+#define IIO_IIDSR	0x400138	/* Interrupt destination */
+
+#define IIO_IIBUSERR	0x1400208	/* Reads here cause a bus error. */
+
+/* IO Interrupt Destination Register */
+#define IIO_IIDSR_SENT_SHIFT	28
+#define IIO_IIDSR_SENT_MASK	0x10000000
+#define IIO_IIDSR_ENB_SHIFT	24
+#define IIO_IIDSR_ENB_MASK	0x01000000
+#define IIO_IIDSR_NODE_SHIFT	8
+#define IIO_IIDSR_NODE_MASK	0x0000ff00
+#define IIO_IIDSR_LVL_SHIFT	0
+#define IIO_IIDSR_LVL_MASK	0x0000003f
+
+
+/* GFX Flow Control Node/Widget Register */
+#define IIO_IGFX_0	0x400140	/* gfx node/widget register 0 */
+#define IIO_IGFX_1	0x400148	/* gfx node/widget register 1 */
+#define IIO_IGFX_W_NUM_BITS	4	/* size of widget num field */
+#define IIO_IGFX_W_NUM_MASK	((1<<IIO_IGFX_W_NUM_BITS)-1)
+#define IIO_IGFX_W_NUM_SHIFT	0
+#define IIO_IGFX_N_NUM_BITS	9	/* size of node num field */
+#define IIO_IGFX_N_NUM_MASK	((1<<IIO_IGFX_N_NUM_BITS)-1)
+#define IIO_IGFX_N_NUM_SHIFT	4
+#define IIO_IGFX_P_NUM_BITS	1	/* size of processor num field */
+#define IIO_IGFX_P_NUM_MASK	((1<<IIO_IGFX_P_NUM_BITS)-1)
+#define IIO_IGFX_P_NUM_SHIFT	16
+#define IIO_IGFX_VLD_BITS	1	/* size of valid field */
+#define IIO_IGFX_VLD_MASK	((1<<IIO_IGFX_VLD_BITS)-1)
+#define IIO_IGFX_VLD_SHIFT	20
+#define IIO_IGFX_INIT(widget, node, cpu, valid)				(\
+	(((widget) & IIO_IGFX_W_NUM_MASK) << IIO_IGFX_W_NUM_SHIFT) |	 \
+	(((node)   & IIO_IGFX_N_NUM_MASK) << IIO_IGFX_N_NUM_SHIFT) |	 \
+	(((cpu)	   & IIO_IGFX_P_NUM_MASK) << IIO_IGFX_P_NUM_SHIFT) |	 \
+	(((valid)  & IIO_IGFX_VLD_MASK)	  << IIO_IGFX_VLD_SHIFT)	 )
+
+/* Scratch registers (not all bits available) */
+#define IIO_SCRATCH_REG0	0x400150
+#define IIO_SCRATCH_REG1	0x400158
+#define IIO_SCRATCH_MASK	0x0000000f00f11fff
+
+#define IIO_SCRATCH_BIT0_0	0x0000000800000000
+#define IIO_SCRATCH_BIT0_1	0x0000000400000000
+#define IIO_SCRATCH_BIT0_2	0x0000000200000000
+#define IIO_SCRATCH_BIT0_3	0x0000000100000000
+#define IIO_SCRATCH_BIT0_4	0x0000000000800000
+#define IIO_SCRATCH_BIT0_5	0x0000000000400000
+#define IIO_SCRATCH_BIT0_6	0x0000000000200000
+#define IIO_SCRATCH_BIT0_7	0x0000000000100000
+#define IIO_SCRATCH_BIT0_8	0x0000000000010000
+#define IIO_SCRATCH_BIT0_9	0x0000000000001000
+#define IIO_SCRATCH_BIT0_R	0x0000000000000fff
+
+/* IO Translation Table Entries */
+#define IIO_NUM_ITTES	7		/* ITTEs numbered 0..6 */
+					/* Hw manuals number them 1..7! */
+
+/*
+ * As a permanent workaround for a bug in the PI side of the hub, we've
+ * redefined big window 7 as small window 0.
+ */
+#define HUB_NUM_BIG_WINDOW	IIO_NUM_ITTES - 1
+
+/*
+ * Use the top big window as a surrogate for the first small window
+ */
+#define SWIN0_BIGWIN		HUB_NUM_BIG_WINDOW
+
+#define ILCSR_WARM_RESET	0x100
+/*
+ * The IO LLP control status register and widget control register
+ */
+#ifndef __ASSEMBLY__
+
+typedef union hubii_wid_u {
+	u64	wid_reg_value;
+	struct {
+		u64	wid_rsvd:	32,	/* unused */
+			wid_rev_num:	 4,	/* revision number */
+			wid_part_num:	16,	/* the widget type: hub=c101 */
+			wid_mfg_num:	11,	/* Manufacturer id (IBM) */
+			wid_rsvd1:	 1;	/* Reserved */
+	} wid_fields_s;
+} hubii_wid_t;
+
+
+typedef union hubii_wcr_u {
+	u64	wcr_reg_value;
+	struct {
+		u64	wcr_rsvd:	41,	/* unused */
+			wcr_e_thresh:	 5,	/* elasticity threshold */
+			wcr_dir_con:	 1,	/* widget direct connect */
+			wcr_f_bad_pkt:	 1,	/* Force bad llp pkt enable */
+			wcr_xbar_crd:	 3,	/* LLP crossbar credit */
+			wcr_rsvd1:	 8,	/* Reserved */
+			wcr_tag_mode:	 1,	/* Tag mode */
+			wcr_widget_id:	 4;	/* LLP crossbar credit */
+	} wcr_fields_s;
+} hubii_wcr_t;
+
+#define iwcr_dir_con	wcr_fields_s.wcr_dir_con
+
+typedef union hubii_wstat_u {
+	u64	 reg_value;
+	struct {
+		u64	rsvd1:		31,
+			crazy:		 1,	/* Crazy bit		*/
+			rsvd2:		 8,
+			llp_tx_cnt:	 8,	/* LLP Xmit retry counter */
+			rsvd3:		 6,
+			tx_max_rtry:	 1,	/* LLP Retry Timeout Signal */
+			rsvd4:		 2,
+			xt_tail_to:	 1,	/* Xtalk Tail Timeout	*/
+			xt_crd_to:	 1,	/* Xtalk Credit Timeout */
+			pending:	 4;	/* Pending Requests	*/
+	} wstat_fields_s;
+} hubii_wstat_t;
+
+
+typedef union hubii_ilcsr_u {
+	u64	icsr_reg_value;
+	struct {
+		u64	icsr_rsvd:	22,	/* unused */
+			icsr_max_burst: 10,	/* max burst */
+			icsr_rsvd4:	 6,	/* reserved */
+			icsr_max_retry: 10,	/* max retry */
+			icsr_rsvd3:	 2,	/* reserved */
+			icsr_lnk_stat:	 2,	/* link status */
+			icsr_bm8:	 1,	/* Bit mode 8 */
+			icsr_llp_en:	 1,	/* LLP enable bit */
+			icsr_rsvd2:	 1,	/* reserver */
+			icsr_wrm_reset:	 1,	/* Warm reset bit */
+			icsr_rsvd1:	 2,	/* Data ready offset */
+			icsr_null_to:	 6;	/* Null timeout	  */
+
+	} icsr_fields_s;
+} hubii_ilcsr_t;
+
+
+typedef union hubii_iowa_u {
+	u64	iowa_reg_value;
+	struct {
+		u64	iowa_rsvd:	48,	/* unused */
+			iowa_wxoac:	 8,	/* xtalk widget access bits */
+			iowa_rsvd1:	 7,	/* xtalk widget access bits */
+			iowa_w0oac:	 1;	/* xtalk widget access bits */
+	} iowa_fields_s;
+} hubii_iowa_t;
+
+typedef union hubii_iiwa_u {
+	u64	iiwa_reg_value;
+	struct {
+		u64	iiwa_rsvd:	48,	/* unused */
+			iiwa_wxiac:	 8,	/* hub wid access bits */
+			iiwa_rsvd1:	 7,	/* reserved */
+			iiwa_w0iac:	 1;	/* hub wid0 access */
+	} iiwa_fields_s;
+} hubii_iiwa_t;
+
+typedef union	hubii_illr_u {
+	u64	illr_reg_value;
+	struct {
+		u64	illr_rsvd:	32,	/* unused */
+			illr_cb_cnt:	16,	/* checkbit error count */
+			illr_sn_cnt:	16;	/* sequence number count */
+	} illr_fields_s;
+} hubii_illr_t;
+
+/* The structures below are defined to extract and modify the ii
+performance registers */
+
+/* io_perf_sel allows the caller to specify what tests will be
+   performed */
+typedef union io_perf_sel {
+	u64 perf_sel_reg;
+	struct {
+		u64	perf_rsvd  : 48,
+			perf_icct  :  8,
+			perf_ippr1 :  4,
+			perf_ippr0 :  4;
+	} perf_sel_bits;
+} io_perf_sel_t;
+
+/* io_perf_cnt is to extract the count from the hub registers. Due to
+   hardware problems there is only one counter, not two. */
+
+typedef union io_perf_cnt {
+	u64	perf_cnt;
+	struct {
+		u64	perf_rsvd1 : 32,
+			perf_rsvd2 : 12,
+			perf_cnt   : 20;
+	} perf_cnt_bits;
+} io_perf_cnt_t;
+
+#endif /* !__ASSEMBLY__ */
+
+
+#define LNK_STAT_WORKING	0x2
+
+#define IIO_LLP_CB_MAX	0xffff
+#define IIO_LLP_SN_MAX	0xffff
+
+/* IO PRB Entries */
+#define IIO_NUM_IPRBS	(9)
+#define IIO_IOPRB_0	0x400198	/* PRB entry 0 */
+#define IIO_IOPRB_8	0x4001a0	/* PRB entry 8 */
+#define IIO_IOPRB_9	0x4001a8	/* PRB entry 9 */
+#define IIO_IOPRB_A	0x4001b0	/* PRB entry a */
+#define IIO_IOPRB_B	0x4001b8	/* PRB entry b */
+#define IIO_IOPRB_C	0x4001c0	/* PRB entry c */
+#define IIO_IOPRB_D	0x4001c8	/* PRB entry d */
+#define IIO_IOPRB_E	0x4001d0	/* PRB entry e */
+#define IIO_IOPRB_F	0x4001d8	/* PRB entry f */
+
+
+#define IIO_IXCC	0x4001e0	/* Crosstalk credit count timeout */
+#define IIO_IXTCC	IIO_IXCC
+#define IIO_IMEM	0x4001e8	/* Miscellaneous Enable Mask */
+#define IIO_IXTT	0x4001f0	/* Crosstalk tail timeout */
+#define IIO_IECLR	0x4001f8	/* IO error clear */
+#define IIO_IBCN	0x400200	/* IO BTE CRB count */
+
+/*
+ * IIO_IMEM Register fields.
+ */
+#define IIO_IMEM_W0ESD	0x1		/* Widget 0 shut down due to error */
+#define IIO_IMEM_B0ESD	(1 << 4)	/* BTE 0 shut down due to error */
+#define IIO_IMEM_B1ESD	(1 << 8)	/* BTE 1 Shut down due to error */
+
+/* PIO Read address Table Entries */
+#define IIO_IPCA	0x400300	/* PRB Counter adjust */
+#define IIO_NUM_PRTES	8		/* Total number of PRB table entries */
+#define IIO_PRTE_0	0x400308	/* PIO Read address table entry 0 */
+#define IIO_PRTE(_x)	(IIO_PRTE_0 + (8 * (_x)))
+#define IIO_WIDPRTE(x)	IIO_PRTE(((x) - 8)) /* widget ID to its PRTE num */
+#define IIO_IPDR	0x400388	/* PIO table entry deallocation */
+#define IIO_ICDR	0x400390	/* CRB Entry Deallocation */
+#define IIO_IFDR	0x400398	/* IOQ FIFO Depth */
+#define IIO_IIAP	0x4003a0	/* IIQ Arbitration Parameters */
+#define IIO_IMMR	IIO_IIAP
+#define IIO_ICMR	0x4003a8	/* CRB Management Register */
+#define IIO_ICCR	0x4003b0	/* CRB Control Register */
+#define IIO_ICTO	0x4003b8	/* CRB Time Out Register */
+#define IIO_ICTP	0x4003c0	/* CRB Time Out Prescalar */
+
+
+/*
+ * ICMR register fields
+ */
+#define IIO_ICMR_PC_VLD_SHFT	36
+#define IIO_ICMR_PC_VLD_MASK	(0x7fffUL << IIO_ICMR_PC_VLD_SHFT)
+
+#define IIO_ICMR_CRB_VLD_SHFT	20
+#define IIO_ICMR_CRB_VLD_MASK	(0x7fffUL << IIO_ICMR_CRB_VLD_SHFT)
+
+#define IIO_ICMR_FC_CNT_SHFT	16
+#define IIO_ICMR_FC_CNT_MASK	(0xf << IIO_ICMR_FC_CNT_SHFT)
+
+#define IIO_ICMR_C_CNT_SHFT	4
+#define IIO_ICMR_C_CNT_MASK	(0xf << IIO_ICMR_C_CNT_SHFT)
+
+#define IIO_ICMR_P_CNT_SHFT	0
+#define IIO_ICMR_P_CNT_MASK	(0xf << IIO_ICMR_P_CNT_SHFT)
+
+#define IIO_ICMR_PRECISE	(1UL << 52)
+#define IIO_ICMR_CLR_RPPD	(1UL << 13)
+#define IIO_ICMR_CLR_RQPD	(1UL << 12)
+
+/*
+ * IIO PIO Deallocation register field masks : (IIO_IPDR)
+ */
+#define IIO_IPDR_PND	(1 << 4)
+
+/*
+ * IIO CRB deallocation register field masks: (IIO_ICDR)
+ */
+#define IIO_ICDR_PND	(1 << 4)
+
+/*
+ * IIO CRB control register Fields: IIO_ICCR
+ */
+#define IIO_ICCR_PENDING	(0x10000)
+#define IIO_ICCR_CMD_MASK	(0xFF)
+#define IIO_ICCR_CMD_SHFT	(7)
+#define IIO_ICCR_CMD_NOP	(0x0)	/* No Op */
+#define IIO_ICCR_CMD_WAKE	(0x100) /* Reactivate CRB entry and process */
+#define IIO_ICCR_CMD_TIMEOUT	(0x200) /* Make CRB timeout & mark invalid */
+#define IIO_ICCR_CMD_EJECT	(0x400) /* Contents of entry written to memory
+					 * via a WB
+					 */
+#define IIO_ICCR_CMD_FLUSH	(0x800)
+
+/*
+ * CRB manipulation macros
+ *	The CRB macros are slightly complicated, since there are up to
+ *	four registers associated with each CRB entry.
+ */
+#define IIO_NUM_CRBS		15	/* Number of CRBs */
+#define IIO_NUM_NORMAL_CRBS	12	/* Number of regular CRB entries */
+#define IIO_NUM_PC_CRBS		4	/* Number of partial cache CRBs */
+#define IIO_ICRB_OFFSET		8
+#define IIO_ICRB_0		0x400400
+/* XXX - This is now tuneable:
+	#define IIO_FIRST_PC_ENTRY 12
+ */
+
+#define IIO_ICRB_A(_x)	(IIO_ICRB_0 + (4 * IIO_ICRB_OFFSET * (_x)))
+#define IIO_ICRB_B(_x)	(IIO_ICRB_A(_x) + 1*IIO_ICRB_OFFSET)
+#define IIO_ICRB_C(_x)	(IIO_ICRB_A(_x) + 2*IIO_ICRB_OFFSET)
+#define IIO_ICRB_D(_x)	(IIO_ICRB_A(_x) + 3*IIO_ICRB_OFFSET)
+
+/* XXX - IBUE register coming for Hub 2 */
+
+/*
+ *
+ * CRB Register description.
+ *
+ * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING
+ * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING
+ * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING
+ * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING
+ * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING
+ *
+ * Many of the fields in CRB are status bits used by hardware
+ * for implementation of the protocol. It's very dangerous to
+ * mess around with the CRB registers.
+ *
+ * It's OK to read the CRB registers and try to make sense out of the
+ * fields in CRB.
+ *
+ * Updating CRB requires all activities in Hub IIO to be quiesced.
+ * otherwise, a write to CRB could corrupt other CRB entries.
+ * CRBs are here only as a back door peek to hub IIO's status.
+ * Quiescing implies  no dmas no PIOs
+ * either directly from the cpu or from sn0net.
+ * this is not something that can be done easily. So, AVOID updating
+ * CRBs.
+ */
+
+/*
+ * Fields in CRB Register A
+ */
+#ifndef __ASSEMBLY__
+typedef union icrba_u {
+	u64	reg_value;
+	struct {
+		u64	resvd:	6,
+			stall_bte0: 1,	/* Stall BTE 0 */
+			stall_bte1: 1,	/* Stall BTE 1 */
+			error:	1,	/* CRB has an error	*/
+			ecode:	3,	/* Error Code		*/
+			lnetuce: 1,	/* SN0net Uncorrectable error */
+			mark:	1,	/* CRB Has been marked	*/
+			xerr:	1,	/* Error bit set in xtalk header */
+			sidn:	4,	/* SIDN field from xtalk	*/
+			tnum:	5,	/* TNUM field in xtalk		*/
+			addr:	38,	/* Address of request	*/
+			valid:	1,	/* Valid status		*/
+			iow:	1;	/* IO Write operation	*/
+	} icrba_fields_s;
+} icrba_t;
+
+/* This is an alternate typedef for the HUB1 CRB A in order to allow
+   runtime selection of the format based on the REV_ID field of the
+   NI_STATUS_REV_ID register. */
+typedef union h1_icrba_u {
+	u64	reg_value;
+
+	struct {
+		u64	resvd:	6,
+			unused: 1,	/* Unused but RW!!	*/
+			error:	1,	/* CRB has an error	*/
+			ecode:	4,	/* Error Code		*/
+			lnetuce: 1,	/* SN0net Uncorrectable error */
+			mark:	1,	/* CRB Has been marked	*/
+			xerr:	1,	/* Error bit set in xtalk header */
+			sidn:	4,	/* SIDN field from xtalk	*/
+			tnum:	5,	/* TNUM field in xtalk		*/
+			addr:	38,	/* Address of request	*/
+			valid:	1,	/* Valid status		*/
+			iow:	1;	/* IO Write operation	*/
+	} h1_icrba_fields_s;
+} h1_icrba_t;
+
+/* XXX - Is this still right?  Check the spec. */
+#define ICRBN_A_CERR_SHFT	54
+#define ICRBN_A_ERR_MASK	0x3ff
+
+#endif /* !__ASSEMBLY__ */
+
+#define IIO_ICRB_ADDR_SHFT	2	/* Shift to get proper address */
+
+/*
+ * values for "ecode" field
+ */
+#define IIO_ICRB_ECODE_DERR	0	/* Directory error due to IIO access */
+#define IIO_ICRB_ECODE_PERR	1	/* Poison error on IO access */
+#define IIO_ICRB_ECODE_WERR	2	/* Write error by IIO access
+					 * e.g. WINV to a Read only line.
+					 */
+#define IIO_ICRB_ECODE_AERR	3	/* Access error caused by IIO access */
+#define IIO_ICRB_ECODE_PWERR	4	/* Error on partial write	*/
+#define IIO_ICRB_ECODE_PRERR	5	/* Error on partial read	*/
+#define IIO_ICRB_ECODE_TOUT	6	/* CRB timeout before deallocating */
+#define IIO_ICRB_ECODE_XTERR	7	/* Incoming xtalk pkt had error bit */
+
+
+
+/*
+ * Fields in CRB Register B
+ */
+#ifndef __ASSEMBLY__
+typedef union icrbb_u {
+	u64	reg_value;
+	struct {
+	    u64 rsvd1:	5,
+		btenum: 1,	/* BTE to which entry belongs to */
+		cohtrans: 1,	/* Coherent transaction */
+		xtsize: 2,	/* Xtalk operation size
+				 * 0: Double Word
+				 * 1: 32 Bytes.
+				 * 2: 128 Bytes,
+				 * 3: Reserved.
+				 */
+		srcnode: 9,	/* Source Node ID		*/
+		srcinit: 2,	/* Source Initiator:
+				 * See below for field values.
+				 */
+		useold: 1,	/* Use OLD command for processing */
+		imsgtype: 2,	/* Incoming message type
+				 * see below for field values
+				 */
+		imsg:	8,	/* Incoming message	*/
+		initator: 3,	/* Initiator of original request
+				 * See below for field values.
+				 */
+		reqtype: 5,	/* Identifies type of request
+				 * See below for field values.
+				 */
+		rsvd2:	7,
+		ackcnt: 11,	/* Invalidate ack count */
+		resp:	1,	/* data response  given to processor */
+		ack:	1,	/* indicates data ack received	*/
+		hold:	1,	/* entry is gathering inval acks */
+		wb_pend:1,	/* waiting for writeback to complete */
+		intvn:	1,	/* Intervention */
+		stall_ib: 1,	/* Stall Ibuf (from crosstalk) */
+		stall_intr: 1;	/* Stall internal interrupts */
+	} icrbb_field_s;
+} icrbb_t;
+
+/* This is an alternate typedef for the HUB1 CRB B in order to allow
+   runtime selection of the format based on the REV_ID field of the
+   NI_STATUS_REV_ID register. */
+typedef union h1_icrbb_u {
+	u64	reg_value;
+	struct {
+		u64	rsvd1:	5,
+			btenum: 1,	/* BTE to which entry belongs to */
+			cohtrans: 1,	/* Coherent transaction */
+			xtsize: 2,	/* Xtalk operation size
+					 * 0: Double Word
+					 * 1: 32 Bytes.
+					 * 2: 128 Bytes,
+					 * 3: Reserved.
+					 */
+			srcnode: 9,	/* Source Node ID		*/
+			srcinit: 2,	/* Source Initiator:
+					 * See below for field values.
+					 */
+			useold: 1,	/* Use OLD command for processing */
+			imsgtype: 2,	/* Incoming message type
+					 * see below for field values
+					 */
+			imsg:	8,	/* Incoming message	*/
+			initator: 3,	/* Initiator of original request
+					 * See below for field values.
+					 */
+			rsvd2:	1,
+			pcache: 1,	/* entry belongs to partial cache */
+			reqtype: 5,	/* Identifies type of request
+					 * See below for field values.
+					 */
+			stl_ib: 1,	/* stall Ibus coming from xtalk */
+			stl_intr: 1,	/* Stall internal interrupts */
+			stl_bte0: 1,	/* Stall BTE 0	*/
+			stl_bte1: 1,	/* Stall BTE 1	*/
+			intrvn: 1,	/* Req was target of intervention */
+			ackcnt: 11,	/* Invalidate ack count */
+			resp:	1,	/* data response  given to processor */
+			ack:	1,	/* indicates data ack received	*/
+			hold:	1,	/* entry is gathering inval acks */
+			wb_pend:1,	/* waiting for writeback to complete */
+			sleep:	1,	/* xtalk req sleeping till IO-sync */
+			pnd_reply: 1,	/* replies not issed due to IOQ full */
+			pnd_req: 1;	/* reqs not issued due to IOQ full */
+	} h1_icrbb_field_s;
+} h1_icrbb_t;
+
+
+#define b_imsgtype	icrbb_field_s.imsgtype
+#define b_btenum	icrbb_field_s.btenum
+#define b_cohtrans	icrbb_field_s.cohtrans
+#define b_xtsize	icrbb_field_s.xtsize
+#define b_srcnode	icrbb_field_s.srcnode
+#define b_srcinit	icrbb_field_s.srcinit
+#define b_imsgtype	icrbb_field_s.imsgtype
+#define b_imsg		icrbb_field_s.imsg
+#define b_initiator	icrbb_field_s.initiator
+
+#endif /* !__ASSEMBLY__ */
+
+/*
+ * values for field xtsize
+ */
+#define IIO_ICRB_XTSIZE_DW	0	/* Xtalk operation size is 8 bytes  */
+#define IIO_ICRB_XTSIZE_32	1	/* Xtalk operation size is 32 bytes */
+#define IIO_ICRB_XTSIZE_128	2	/* Xtalk operation size is 128 bytes */
+
+/*
+ * values for field srcinit
+ */
+#define IIO_ICRB_PROC0		0	/* Source of request is Proc 0 */
+#define IIO_ICRB_PROC1		1	/* Source of request is Proc 1 */
+#define IIO_ICRB_GB_REQ		2	/* Source is Guaranteed BW request */
+#define IIO_ICRB_IO_REQ		3	/* Source is Normal IO request	*/
+
+/*
+ * Values for field imsgtype
+ */
+#define IIO_ICRB_IMSGT_XTALK	0	/* Incoming Message from Xtalk */
+#define IIO_ICRB_IMSGT_BTE	1	/* Incoming message from BTE	*/
+#define IIO_ICRB_IMSGT_SN0NET	2	/* Incoming message from SN0 net */
+#define IIO_ICRB_IMSGT_CRB	3	/* Incoming message from CRB ???  */
+
+/*
+ * values for field initiator.
+ */
+#define IIO_ICRB_INIT_XTALK	0	/* Message originated in xtalk	*/
+#define IIO_ICRB_INIT_BTE0	0x1	/* Message originated in BTE 0	*/
+#define IIO_ICRB_INIT_SN0NET	0x2	/* Message originated in SN0net */
+#define IIO_ICRB_INIT_CRB	0x3	/* Message originated in CRB ?	*/
+#define IIO_ICRB_INIT_BTE1	0x5	/* MEssage originated in BTE 1	*/
+
+/*
+ * Values for field reqtype.
+ */
+/* XXX - Need to fix this for Hub 2 */
+#define IIO_ICRB_REQ_DWRD	0	/* Request type double word	*/
+#define IIO_ICRB_REQ_QCLRD	1	/* Request is Qrtr Caceh line Rd */
+#define IIO_ICRB_REQ_BLKRD	2	/* Request is block read	*/
+#define IIO_ICRB_REQ_RSHU	6	/* Request is BTE block read	*/
+#define IIO_ICRB_REQ_REXU	7	/* request is BTE Excl Read	*/
+#define IIO_ICRB_REQ_RDEX	8	/* Request is Read Exclusive	*/
+#define IIO_ICRB_REQ_WINC	9	/* Request is Write Invalidate	*/
+#define IIO_ICRB_REQ_BWINV	10	/* Request is BTE Winv		*/
+#define IIO_ICRB_REQ_PIORD	11	/* Request is PIO read		*/
+#define IIO_ICRB_REQ_PIOWR	12	/* Request is PIO Write		*/
+#define IIO_ICRB_REQ_PRDM	13	/* Request is Fetch&Op		*/
+#define IIO_ICRB_REQ_PWRM	14	/* Request is Store &Op		*/
+#define IIO_ICRB_REQ_PTPWR	15	/* Request is Peer to peer	*/
+#define IIO_ICRB_REQ_WB		16	/* Request is Write back	*/
+#define IIO_ICRB_REQ_DEX	17	/* Retained DEX Cache line	*/
+
+/*
+ * Fields in CRB Register C
+ */
+
+#ifndef __ASSEMBLY__
+
+typedef union icrbc_s {
+	u64	reg_value;
+	struct {
+		u64	rsvd:	6,
+			sleep:	1,
+			pricnt: 4,	/* Priority count sent with Read req */
+			pripsc: 4,	/* Priority Pre scalar	*/
+			bteop:	1,	/* BTE Operation	*/
+			push_be: 34,	/* Push address Byte enable
+					 * Holds push addr, if CRB is for BTE
+					 * If CRB belongs to Partial cache,
+					 * this contains byte enables bits
+					 * ([47:46] = 0)
+					 */
+			suppl:	11,	/* Supplemental field	*/
+			barrop: 1,	/* Barrier Op bit set in xtalk req */
+			doresp: 1,	/* Xtalk req needs a response	*/
+			gbr:	1;	/* GBR bit set in xtalk packet	*/
+	} icrbc_field_s;
+} icrbc_t;
+
+#define c_pricnt	icrbc_field_s.pricnt
+#define c_pripsc	icrbc_field_s.pripsc
+#define c_bteop		icrbc_field_s.bteop
+#define c_bteaddr	icrbc_field_s.push_be	/* push_be field has 2 names */
+#define c_benable	icrbc_field_s.push_be	/* push_be field has 2 names */
+#define c_suppl		icrbc_field_s.suppl
+#define c_barrop	icrbc_field_s.barrop
+#define c_doresp	icrbc_field_s.doresp
+#define c_gbr	icrbc_field_s.gbr
+#endif /* !__ASSEMBLY__ */
+
+/*
+ * Fields in CRB Register D
+ */
+
+#ifndef __ASSEMBLY__
+typedef union icrbd_s {
+	u64	reg_value;
+	struct {
+	    u64 rsvd:	38,
+		toutvld: 1,	/* Timeout in progress for this CRB */
+		ctxtvld: 1,	/* Context field below is valid */
+		rsvd2:	1,
+		context: 15,	/* Bit vector:
+				 * Has a bit set for each CRB entry
+				 * which needs to be deallocated
+				 * before this CRB entry is processed.
+				 * Set only for barrier operations.
+				 */
+		timeout: 8;	/* Timeout Upper 8 bits */
+	} icrbd_field_s;
+} icrbd_t;
+
+#define icrbd_toutvld	icrbd_field_s.toutvld
+#define icrbd_ctxtvld	icrbd_field_s.ctxtvld
+#define icrbd_context	icrbd_field_s.context
+
+
+typedef union hubii_ifdr_u {
+	u64	hi_ifdr_value;
+	struct {
+		u64	ifdr_rsvd:	49,
+			ifdr_maxrp:	 7,
+			ifdr_rsvd1:	 1,
+			ifdr_maxrq:	 7;
+	} hi_ifdr_fields;
+} hubii_ifdr_t;
+
+#endif /* !__ASSEMBLY__ */
+
+/*
+ * Hardware designed names for the BTE control registers.
+ */
+#define IIO_IBLS_0	0x410000	/* BTE length/status 0 */
+#define IIO_IBSA_0	0x410008	/* BTE source address 0 */
+#define IIO_IBDA_0	0x410010	/* BTE destination address 0 */
+#define IIO_IBCT_0	0x410018	/* BTE control/terminate 0 */
+#define IIO_IBNA_0	0x410020	/* BTE notification address 0 */
+#define IIO_IBNR_0	IIO_IBNA_0
+#define IIO_IBIA_0	0x410028	/* BTE interrupt address 0 */
+
+#define IIO_IBLS_1	0x420000	/* BTE length/status 1 */
+#define IIO_IBSA_1	0x420008	/* BTE source address 1 */
+#define IIO_IBDA_1	0x420010	/* BTE destination address 1 */
+#define IIO_IBCT_1	0x420018	/* BTE control/terminate 1 */
+#define IIO_IBNA_1	0x420020	/* BTE notification address 1 */
+#define IIO_IBNR_1	IIO_IBNA_1
+#define IIO_IBIA_1	0x420028	/* BTE interrupt address 1 */
+
+/*
+ * More miscellaneous registers
+ */
+#define IIO_IPCR	0x430000	/* Performance Control */
+#define IIO_IPPR	0x430008	/* Performance Profiling */
+
+/*
+ * IO Error Clear register bit field definitions
+ */
+#define IECLR_BTE1		(1 << 18)  /* clear bte error 1 ??? */
+#define IECLR_BTE0		(1 << 17)  /* clear bte error 0 ??? */
+#define IECLR_CRAZY		(1 << 16)  /* clear crazy bit in wstat reg */
+#define IECLR_PRB_F		(1 << 15)  /* clear err bit in PRB_F reg */
+#define IECLR_PRB_E		(1 << 14)  /* clear err bit in PRB_E reg */
+#define IECLR_PRB_D		(1 << 13)  /* clear err bit in PRB_D reg */
+#define IECLR_PRB_C		(1 << 12)  /* clear err bit in PRB_C reg */
+#define IECLR_PRB_B		(1 << 11)  /* clear err bit in PRB_B reg */
+#define IECLR_PRB_A		(1 << 10)  /* clear err bit in PRB_A reg */
+#define IECLR_PRB_9		(1 << 9)   /* clear err bit in PRB_9 reg */
+#define IECLR_PRB_8		(1 << 8)   /* clear err bit in PRB_8 reg */
+#define IECLR_PRB_0		(1 << 0)   /* clear err bit in PRB_0 reg */
+
+/*
+ * IO PIO Read Table Entry format
+ */
+
+#ifndef __ASSEMBLY__
+
+typedef union iprte_a {
+	u64	entry;
+	struct {
+	    u64 rsvd1	  : 7,	/* Reserved field		*/
+		valid	  : 1,	/* Maps to a timeout entry	*/
+		rsvd2	  : 1,
+		srcnode	  : 9,	/* Node which did this PIO	*/
+		initiator : 2,	/* If T5A or T5B or IO		*/
+		rsvd3	  : 3,
+		addr	  : 38, /* Physical address of PIO	*/
+		rsvd4	  : 3;
+	} iprte_fields;
+} iprte_a_t;
+
+#define iprte_valid	iprte_fields.valid
+#define iprte_timeout	iprte_fields.timeout
+#define iprte_srcnode	iprte_fields.srcnode
+#define iprte_init	iprte_fields.initiator
+#define iprte_addr	iprte_fields.addr
+
+#endif /* !__ASSEMBLY__ */
+
+#define IPRTE_ADDRSHFT	3
+
+/*
+ * Hub IIO PRB Register format.
+ */
+
+#ifndef __ASSEMBLY__
+/*
+ * Note: Fields bnakctr, anakctr, xtalkctrmode, ovflow fields are
+ * "Status" fields, and should only be used in case of clean up after errors.
+ */
+
+typedef union iprb_u {
+	u64	reg_value;
+	struct {
+	    u64 rsvd1:	15,
+		error:	1,	/* Widget rcvd wr resp pkt w/ error */
+		ovflow: 5,	/* Overflow count. perf measurement */
+		fire_and_forget: 1, /* Launch Write without response */
+		mode:	2,	/* Widget operation Mode	*/
+		rsvd2:	2,
+		bnakctr: 14,
+		rsvd3:	2,
+		anakctr: 14,
+		xtalkctr: 8;
+	} iprb_fields_s;
+} iprb_t;
+
+#define iprb_regval	reg_value
+
+#define iprb_error	iprb_fields_s.error
+#define iprb_ovflow	iprb_fields_s.ovflow
+#define iprb_ff		iprb_fields_s.fire_and_forget
+#define iprb_mode	iprb_fields_s.mode
+#define iprb_bnakctr	iprb_fields_s.bnakctr
+#define iprb_anakctr	iprb_fields_s.anakctr
+#define iprb_xtalkctr	iprb_fields_s.xtalkctr
+
+#endif /* !__ASSEMBLY__ */
+
+/*
+ * values for mode field in iprb_t.
+ * For details of the meanings of NAK and Accept, refer the PIO flow
+ * document
+ */
+#define IPRB_MODE_NORMAL	(0)
+#define IPRB_MODE_COLLECT_A	(1)	/* PRB in collect A mode */
+#define IPRB_MODE_SERVICE_A	(2)	/* NAK B and Accept A */
+#define IPRB_MODE_SERVICE_B	(3)	/* NAK A and Accept B */
+
+/*
+ * IO CRB entry C_A to E_A : Partial (cache) CRBS
+ */
+#ifndef __ASSEMBLY__
+typedef union icrbp_a {
+	u64   ip_reg;	    /* the entire register value	*/
+	struct {
+	     u64 error: 1,  /*	  63, error occurred		*/
+		ln_uce: 1,  /*	  62: uncorrectable memory	*/
+		ln_ae:	1,  /*	  61: protection violation	*/
+		ln_werr:1,  /*	  60: write access error	*/
+		ln_aerr:1,  /*	  59: sn0net: Address error	*/
+		ln_perr:1,  /*	  58: sn0net: poison error	*/
+		timeout:1,  /*	  57: CRB timed out		*/
+		l_bdpkt:1,  /*	  56: truncated pkt on sn0net	*/
+		c_bdpkt:1,  /*	  55: truncated pkt on xtalk	*/
+		c_err:	1,  /*	  54: incoming xtalk req, err set*/
+		rsvd1: 12,  /* 53-42: reserved			*/
+		valid:	1,  /*	  41: Valid status		*/
+		sidn:	4,  /* 40-37: SIDN field of xtalk rqst	*/
+		tnum:	5,  /* 36-32: TNUM of xtalk request	*/
+		bo:	1,  /*	  31: barrier op set in xtalk rqst*/
+		resprqd:1,  /*	  30: xtalk rqst requires response*/
+		gbr:	1,  /*	  29: gbr bit set in xtalk rqst */
+		size:	2,  /* 28-27: size of xtalk request	*/
+		excl:	4,  /* 26-23: exclusive bit(s)		*/
+		stall:	3,  /* 22-20: stall (xtalk, bte 0/1)	*/
+		intvn:	1,  /*	  19: rqst target of intervention*/
+		resp:	1,  /*	  18: Data response given to t5 */
+		ack:	1,  /*	  17: Data ack received.	*/
+		hold:	1,  /*	  16: crb gathering invalidate acks*/
+		wb:	1,  /*	  15: writeback pending.	*/
+		ack_cnt:11, /* 14-04: counter of invalidate acks*/
+		tscaler:4;  /* 03-00: Timeout prescaler		*/
+	} ip_fmt;
+} icrbp_a_t;
+
+#endif /* !__ASSEMBLY__ */
+
+/*
+ * A couple of defines to go with the above structure.
+ */
+#define ICRBP_A_CERR_SHFT	54
+#define ICRBP_A_ERR_MASK	0x3ff
+
+#ifndef __ASSEMBLY__
+typedef union hubii_idsr {
+	u64 iin_reg;
+	struct {
+		u64 rsvd1 : 35,
+		    isent : 1,
+		    rsvd2 : 3,
+		    ienable: 1,
+		    rsvd  : 7,
+		    node  : 9,
+		    rsvd4 : 1,
+		    level : 7;
+	} iin_fmt;
+} hubii_idsr_t;
+#endif /* !__ASSEMBLY__ */
+
+/*
+ * IO BTE Length/Status (IIO_IBLS) register bit field definitions
+ */
+#define IBLS_BUSY		(0x1 << 20)
+#define IBLS_ERROR_SHFT		16
+#define IBLS_ERROR		(0x1 << IBLS_ERROR_SHFT)
+#define IBLS_LENGTH_MASK	0xffff
+
+/*
+ * IO BTE Control/Terminate register (IBCT) register bit field definitions
+ */
+#define IBCT_POISON		(0x1 << 8)
+#define IBCT_NOTIFY		(0x1 << 4)
+#define IBCT_ZFIL_MODE		(0x1 << 0)
+
+/*
+ * IO BTE Interrupt Address Register (IBIA) register bit field definitions
+ */
+#define IBIA_LEVEL_SHFT		16
+#define IBIA_LEVEL_MASK		(0x7f << IBIA_LEVEL_SHFT)
+#define IBIA_NODE_ID_SHFT	0
+#define IBIA_NODE_ID_MASK	(0x1ff)
+
+/*
+ * Miscellaneous hub constants
+ */
+
+/* Number of widgets supported by hub */
+#define HUB_NUM_WIDGET		9
+#define HUB_WIDGET_ID_MIN	0x8
+#define HUB_WIDGET_ID_MAX	0xf
+
+#define HUB_WIDGET_PART_NUM	0xc101
+#define MAX_HUBS_PER_XBOW	2
+
+/*
+ * Get a hub's widget id from widget control register
+ */
+#define IIO_WCR_WID_GET(nasid)	(REMOTE_HUB_L(nasid, III_WCR) & 0xf)
+#define IIO_WST_ERROR_MASK	(UINT64_CAST 1 << 32) /* Widget status error */
+
+/*
+ * Number of credits Hub widget has while sending req/response to
+ * xbow.
+ * Value of 3 is required by Xbow 1.1
+ * We may be able to increase this to 4 with Xbow 1.2.
+ */
+#define	      HUBII_XBOW_CREDIT	      3
+#define	      HUBII_XBOW_REV2_CREDIT  4
+
+#endif /* _ASM_SGI_SN_SN0_HUBIO_H */
diff --git a/arch/mips/include/asm/sn/sn0/hubmd.h b/arch/mips/include/asm/sn/sn0/hubmd.h
new file mode 100644
index 000000000..305d002be
--- /dev/null
+++ b/arch/mips/include/asm/sn/sn0/hubmd.h
@@ -0,0 +1,789 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Derived from IRIX <sys/SN/SN0/hubmd.h>, revision 1.59.
+ *
+ * Copyright (C) 1992 - 1997, 1999 Silicon Graphics, Inc.
+ * Copyright (C) 1999 by Ralf Baechle
+ */
+#ifndef _ASM_SN_SN0_HUBMD_H
+#define _ASM_SN_SN0_HUBMD_H
+
+
+/*
+ * Hub Memory/Directory interface registers
+ */
+#define CACHE_SLINE_SIZE	128	/* Secondary cache line size on SN0 */
+
+#define MAX_REGIONS		64
+
+/* Hardware page size and shift */
+
+#define MD_PAGE_SIZE		4096	 /* Page size in bytes		    */
+#define MD_PAGE_NUM_SHFT	12	 /* Address to page number shift    */
+
+/* Register offsets from LOCAL_HUB or REMOTE_HUB */
+
+#define MD_BASE			0x200000
+#define MD_BASE_PERF		0x210000
+#define MD_BASE_JUNK		0x220000
+
+#define MD_IO_PROTECT		0x200000 /* MD and core register protection */
+#define MD_IO_PROT_OVRRD	0x200008 /* Clear my bit in MD_IO_PROTECT   */
+#define MD_HSPEC_PROTECT	0x200010 /* BDDIR, LBOOT, RBOOT protection  */
+#define MD_MEMORY_CONFIG	0x200018 /* Memory/Directory DIMM control   */
+#define MD_REFRESH_CONTROL	0x200020 /* Memory/Directory refresh ctrl   */
+#define MD_FANDOP_CAC_STAT	0x200028 /* Fetch-and-op cache status	    */
+#define MD_MIG_DIFF_THRESH	0x200030 /* Page migr. count diff thresh.   */
+#define MD_MIG_VALUE_THRESH	0x200038 /* Page migr. count abs. thresh.   */
+#define MD_MIG_CANDIDATE	0x200040 /* Latest page migration candidate */
+#define MD_MIG_CANDIDATE_CLR	0x200048 /* Clear page migration candidate  */
+#define MD_DIR_ERROR		0x200050 /* Directory DIMM error	    */
+#define MD_DIR_ERROR_CLR	0x200058 /* Directory DIMM error clear	    */
+#define MD_PROTOCOL_ERROR	0x200060 /* Directory protocol error	    */
+#define MD_PROTOCOL_ERROR_CLR	0x200068 /* Directory protocol error clear  */
+#define MD_MEM_ERROR		0x200070 /* Memory DIMM error		    */
+#define MD_MEM_ERROR_CLR	0x200078 /* Memory DIMM error clear	    */
+#define MD_MISC_ERROR		0x200080 /* Miscellaneous MD error	    */
+#define MD_MISC_ERROR_CLR	0x200088 /* Miscellaneous MD error clear    */
+#define MD_MEM_DIMM_INIT	0x200090 /* Memory DIMM mode initization.   */
+#define MD_DIR_DIMM_INIT	0x200098 /* Directory DIMM mode init.	    */
+#define MD_MOQ_SIZE		0x2000a0 /* MD outgoing queue size	    */
+#define MD_MLAN_CTL		0x2000a8 /* NIC (Microlan) control register */
+
+#define MD_PERF_SEL		0x210000 /* Select perf monitor events	    */
+#define MD_PERF_CNT0		0x210010 /* Performance counter 0	    */
+#define MD_PERF_CNT1		0x210018 /* Performance counter 1	    */
+#define MD_PERF_CNT2		0x210020 /* Performance counter 2	    */
+#define MD_PERF_CNT3		0x210028 /* Performance counter 3	    */
+#define MD_PERF_CNT4		0x210030 /* Performance counter 4	    */
+#define MD_PERF_CNT5		0x210038 /* Performance counter 5	    */
+
+#define MD_UREG0_0		0x220000 /* uController/UART 0 register	    */
+#define MD_UREG0_1		0x220008 /* uController/UART 0 register	    */
+#define MD_UREG0_2		0x220010 /* uController/UART 0 register	    */
+#define MD_UREG0_3		0x220018 /* uController/UART 0 register	    */
+#define MD_UREG0_4		0x220020 /* uController/UART 0 register	    */
+#define MD_UREG0_5		0x220028 /* uController/UART 0 register	    */
+#define MD_UREG0_6		0x220030 /* uController/UART 0 register	    */
+#define MD_UREG0_7		0x220038 /* uController/UART 0 register	    */
+
+#define MD_SLOTID_USTAT		0x220048 /* Hub slot ID & UART/uCtlr status */
+#define MD_LED0			0x220050 /* Eight-bit LED for CPU A	    */
+#define MD_LED1			0x220058 /* Eight-bit LED for CPU B	    */
+
+#define MD_UREG1_0		0x220080 /* uController/UART 1 register	    */
+#define MD_UREG1_1		0x220088 /* uController/UART 1 register	    */
+#define MD_UREG1_2		0x220090 /* uController/UART 1 register	    */
+#define MD_UREG1_3		0x220098 /* uController/UART 1 register	    */
+#define MD_UREG1_4		0x2200a0 /* uController/UART 1 register	    */
+#define MD_UREG1_5		0x2200a8 /* uController/UART 1 register	    */
+#define MD_UREG1_6		0x2200b0 /* uController/UART 1 register	    */
+#define MD_UREG1_7		0x2200b8 /* uController/UART 1 register	    */
+#define MD_UREG1_8		0x2200c0 /* uController/UART 1 register	    */
+#define MD_UREG1_9		0x2200c8 /* uController/UART 1 register	    */
+#define MD_UREG1_10		0x2200d0 /* uController/UART 1 register	    */
+#define MD_UREG1_11		0x2200d8 /* uController/UART 1 register	    */
+#define MD_UREG1_12		0x2200e0 /* uController/UART 1 register	    */
+#define MD_UREG1_13		0x2200e8 /* uController/UART 1 register	    */
+#define MD_UREG1_14		0x2200f0 /* uController/UART 1 register	    */
+#define MD_UREG1_15		0x2200f8 /* uController/UART 1 register	    */
+
+#ifdef CONFIG_SGI_SN_N_MODE
+#define MD_MEM_BANKS		4	 /* 4 banks of memory max in N mode */
+#else
+#define MD_MEM_BANKS		8	 /* 8 banks of memory max in M mode */
+#endif
+
+/*
+ * MD_MEMORY_CONFIG fields
+ *
+ *   MD_SIZE_xxx are useful for representing the size of a SIMM or bank
+ *   (SIMM pair).  They correspond to the values needed for the bit
+ *   triplets (MMC_BANK_MASK) in the MD_MEMORY_CONFIG register for bank size.
+ *   Bits not used by the MD are used by software.
+ */
+
+#define MD_SIZE_EMPTY		0	/* Valid in MEMORY_CONFIG	    */
+#define MD_SIZE_8MB		1
+#define MD_SIZE_16MB		2
+#define MD_SIZE_32MB		3	/* Broken in Hub 1		    */
+#define MD_SIZE_64MB		4	/* Valid in MEMORY_CONFIG	    */
+#define MD_SIZE_128MB		5	/* Valid in MEMORY_CONFIG	    */
+#define MD_SIZE_256MB		6
+#define MD_SIZE_512MB		7	/* Valid in MEMORY_CONFIG	    */
+#define MD_SIZE_1GB		8
+#define MD_SIZE_2GB		9
+#define MD_SIZE_4GB		10
+
+#define MD_SIZE_BYTES(size)	((size) == 0 ? 0 : 0x400000L << (size))
+#define MD_SIZE_MBYTES(size)	((size) == 0 ? 0 :   4	     << (size))
+
+#define MMC_FPROM_CYC_SHFT	49	/* Have to use UINT64_CAST, instead */
+#define MMC_FPROM_CYC_MASK	(UINT64_CAST 31 << 49)	/* of 'L' suffix,   */
+#define MMC_FPROM_WR_SHFT	44			/* for assembler    */
+#define MMC_FPROM_WR_MASK	(UINT64_CAST 31 << 44)
+#define MMC_UCTLR_CYC_SHFT	39
+#define MMC_UCTLR_CYC_MASK	(UINT64_CAST 31 << 39)
+#define MMC_UCTLR_WR_SHFT	34
+#define MMC_UCTLR_WR_MASK	(UINT64_CAST 31 << 34)
+#define MMC_DIMM0_SEL_SHFT	32
+#define MMC_DIMM0_SEL_MASK	(UINT64_CAST 3 << 32)
+#define MMC_IO_PROT_EN_SHFT	31
+#define MMC_IO_PROT_EN_MASK	(UINT64_CAST 1 << 31)
+#define MMC_IO_PROT		(UINT64_CAST 1 << 31)
+#define MMC_ARB_MLSS_SHFT	30
+#define MMC_ARB_MLSS_MASK	(UINT64_CAST 1 << 30)
+#define MMC_ARB_MLSS		(UINT64_CAST 1 << 30)
+#define MMC_IGNORE_ECC_SHFT	29
+#define MMC_IGNORE_ECC_MASK	(UINT64_CAST 1 << 29)
+#define MMC_IGNORE_ECC		(UINT64_CAST 1 << 29)
+#define MMC_DIR_PREMIUM_SHFT	28
+#define MMC_DIR_PREMIUM_MASK	(UINT64_CAST 1 << 28)
+#define MMC_DIR_PREMIUM		(UINT64_CAST 1 << 28)
+#define MMC_REPLY_GUAR_SHFT	24
+#define MMC_REPLY_GUAR_MASK	(UINT64_CAST 15 << 24)
+#define MMC_BANK_SHFT(_b)	((_b) * 3)
+#define MMC_BANK_MASK(_b)	(UINT64_CAST 7 << MMC_BANK_SHFT(_b))
+#define MMC_BANK_ALL_MASK	0xffffff
+#define MMC_RESET_DEFAULTS	(UINT64_CAST 0x0f << MMC_FPROM_CYC_SHFT | \
+				 UINT64_CAST 0x07 << MMC_FPROM_WR_SHFT | \
+				 UINT64_CAST 0x1f << MMC_UCTLR_CYC_SHFT | \
+				 UINT64_CAST 0x0f << MMC_UCTLR_WR_SHFT | \
+				 MMC_IGNORE_ECC | MMC_DIR_PREMIUM | \
+				 UINT64_CAST 0x0f << MMC_REPLY_GUAR_SHFT | \
+				 MMC_BANK_ALL_MASK)
+
+/* MD_REFRESH_CONTROL fields */
+
+#define MRC_ENABLE_SHFT		63
+#define MRC_ENABLE_MASK		(UINT64_CAST 1 << 63)
+#define MRC_ENABLE		(UINT64_CAST 1 << 63)
+#define MRC_COUNTER_SHFT	12
+#define MRC_COUNTER_MASK	(UINT64_CAST 0xfff << 12)
+#define MRC_CNT_THRESH_MASK	0xfff
+#define MRC_RESET_DEFAULTS	(UINT64_CAST 0x400)
+
+/* MD_MEM_DIMM_INIT and MD_DIR_DIMM_INIT fields */
+
+#define MDI_SELECT_SHFT		32
+#define MDI_SELECT_MASK		(UINT64_CAST 0x0f << 32)
+#define MDI_DIMM_MODE_MASK	(UINT64_CAST 0xfff)
+
+/* MD_MOQ_SIZE fields */
+
+#define MMS_RP_SIZE_SHFT	8
+#define MMS_RP_SIZE_MASK	(UINT64_CAST 0x3f << 8)
+#define MMS_RQ_SIZE_SHFT	0
+#define MMS_RQ_SIZE_MASK	(UINT64_CAST 0x1f)
+#define MMS_RESET_DEFAULTS	(0x32 << 8 | 0x12)
+
+/* MD_FANDOP_CAC_STAT fields */
+
+#define MFC_VALID_SHFT		63
+#define MFC_VALID_MASK		(UINT64_CAST 1 << 63)
+#define MFC_VALID		(UINT64_CAST 1 << 63)
+#define MFC_ADDR_SHFT		6
+#define MFC_ADDR_MASK		(UINT64_CAST 0x3ffffff)
+
+/* MD_MLAN_CTL fields */
+
+#define MLAN_PHI1_SHFT		27
+#define MLAN_PHI1_MASK		(UINT64_CAST 0x7f << 27)
+#define MLAN_PHI0_SHFT		20
+#define MLAN_PHI0_MASK		(UINT64_CAST 0x7f << 27)
+#define MLAN_PULSE_SHFT		10
+#define MLAN_PULSE_MASK		(UINT64_CAST 0x3ff << 10)
+#define MLAN_SAMPLE_SHFT	2
+#define MLAN_SAMPLE_MASK	(UINT64_CAST 0xff << 2)
+#define MLAN_DONE_SHFT		1
+#define MLAN_DONE_MASK		2
+#define MLAN_DONE		(UINT64_CAST 0x02)
+#define MLAN_RD_DATA		(UINT64_CAST 0x01)
+#define MLAN_RESET_DEFAULTS	(UINT64_CAST 0x31 << MLAN_PHI1_SHFT | \
+				 UINT64_CAST 0x31 << MLAN_PHI0_SHFT)
+
+/* MD_SLOTID_USTAT bit definitions */
+
+#define MSU_CORECLK_TST_SHFT	7	/* You don't wanna know		    */
+#define MSU_CORECLK_TST_MASK	(UINT64_CAST 1 << 7)
+#define MSU_CORECLK_TST		(UINT64_CAST 1 << 7)
+#define MSU_CORECLK_SHFT	6	/* You don't wanna know		    */
+#define MSU_CORECLK_MASK	(UINT64_CAST 1 << 6)
+#define MSU_CORECLK		(UINT64_CAST 1 << 6)
+#define MSU_NETSYNC_SHFT	5	/* You don't wanna know		    */
+#define MSU_NETSYNC_MASK	(UINT64_CAST 1 << 5)
+#define MSU_NETSYNC		(UINT64_CAST 1 << 5)
+#define MSU_FPROMRDY_SHFT	4	/* Flash PROM ready bit		    */
+#define MSU_FPROMRDY_MASK	(UINT64_CAST 1 << 4)
+#define MSU_FPROMRDY		(UINT64_CAST 1 << 4)
+#define MSU_I2CINTR_SHFT		3	/* I2C interrupt bit   */
+#define MSU_I2CINTR_MASK		(UINT64_CAST 1 << 3)
+#define MSU_I2CINTR		(UINT64_CAST 1 << 3)
+#define MSU_SLOTID_MASK		0xff
+#define MSU_SN0_SLOTID_SHFT	0	/* Slot ID			    */
+#define MSU_SN0_SLOTID_MASK	(UINT64_CAST 7)
+#define MSU_SN00_SLOTID_SHFT	7
+#define MSU_SN00_SLOTID_MASK	(UINT64_CAST 0x80)
+
+#define MSU_PIMM_PSC_SHFT	4
+#define MSU_PIMM_PSC_MASK	(0xf << MSU_PIMM_PSC_SHFT)
+
+/* MD_MIG_DIFF_THRESH bit definitions */
+
+#define MD_MIG_DIFF_THRES_VALID_MASK (UINT64_CAST 0x1 << 63)
+#define MD_MIG_DIFF_THRES_VALID_SHFT 63
+#define MD_MIG_DIFF_THRES_VALUE_MASK (UINT64_CAST 0xfffff)
+
+/* MD_MIG_VALUE_THRESH bit definitions */
+
+#define MD_MIG_VALUE_THRES_VALID_MASK (UINT64_CAST 0x1 << 63)
+#define MD_MIG_VALUE_THRES_VALID_SHFT 63
+#define MD_MIG_VALUE_THRES_VALUE_MASK (UINT64_CAST 0xfffff)
+
+/* MD_MIG_CANDIDATE bit definitions */
+
+#define MD_MIG_CANDIDATE_VALID_MASK (UINT64_CAST 0x1 << 63)
+#define MD_MIG_CANDIDATE_VALID_SHFT 63
+#define MD_MIG_CANDIDATE_TYPE_MASK (UINT64_CAST 0x1 << 30)
+#define MD_MIG_CANDIDATE_TYPE_SHFT 30
+#define MD_MIG_CANDIDATE_OVERRUN_MASK (UINT64_CAST 0x1 << 29)
+#define MD_MIG_CANDIDATE_OVERRUN_SHFT 29
+#define MD_MIG_CANDIDATE_INITIATOR_MASK (UINT64_CAST 0x7ff << 18)
+#define MD_MIG_CANDIDATE_INITIATOR_SHFT 18
+#define MD_MIG_CANDIDATE_NODEID_MASK (UINT64_CAST 0x1ff << 20)
+#define MD_MIG_CANDIDATE_NODEID_SHFT 20
+#define MD_MIG_CANDIDATE_ADDR_MASK (UINT64_CAST 0x3ffff)
+#define MD_MIG_CANDIDATE_ADDR_SHFT 14  /* The address starts at bit 14 */
+
+/* Other MD definitions */
+
+#define MD_BANK_SHFT		29			/* log2(512 MB)	    */
+#define MD_BANK_MASK		(UINT64_CAST 7 << 29)
+#define MD_BANK_SIZE		(UINT64_CAST 1 << MD_BANK_SHFT)	  /* 512 MB */
+#define MD_BANK_OFFSET(_b)	(UINT64_CAST (_b) << MD_BANK_SHFT)
+
+/*
+ * The following definitions cover the bit field definitions for the
+ * various MD registers.  For multi-bit registers, we define both
+ * a shift amount and a mask value.  By convention, if you want to
+ * isolate a field, you should mask the field and then shift it down,
+ * since this makes the masks useful without a shift.
+ */
+
+/* Directory entry states for both premium and standard SIMMs. */
+
+#define MD_DIR_SHARED		(UINT64_CAST 0x0)	/* 000 */
+#define MD_DIR_POISONED		(UINT64_CAST 0x1)	/* 001 */
+#define MD_DIR_EXCLUSIVE	(UINT64_CAST 0x2)	/* 010 */
+#define MD_DIR_BUSY_SHARED	(UINT64_CAST 0x3)	/* 011 */
+#define MD_DIR_BUSY_EXCL	(UINT64_CAST 0x4)	/* 100 */
+#define MD_DIR_WAIT		(UINT64_CAST 0x5)	/* 101 */
+#define MD_DIR_UNOWNED		(UINT64_CAST 0x7)	/* 111 */
+
+/*
+ * The MD_DIR_FORCE_ECC bit can be added directory entry write data
+ * to forcing the ECC to be written as-is instead of recalculated.
+ */
+
+#define MD_DIR_FORCE_ECC	(UINT64_CAST 1 << 63)
+
+/*
+ * Premium SIMM directory entry shifts and masks.  Each is valid only in the
+ * context(s) indicated, where A, B, and C indicate the directory entry format
+ * as shown, and low and/or high indicates which double-word of the entry.
+ *
+ * Format A:  STATE = shared, FINE = 1
+ * Format B:  STATE = shared, FINE = 0
+ * Format C:  STATE != shared (FINE must be 0)
+ */
+
+#define MD_PDIR_MASK		0xffffffffffff		/* Whole entry	    */
+#define MD_PDIR_ECC_SHFT	0			/* ABC low or high  */
+#define MD_PDIR_ECC_MASK	0x7f
+#define MD_PDIR_PRIO_SHFT	8			/* ABC low	    */
+#define MD_PDIR_PRIO_MASK	(0xf << 8)
+#define MD_PDIR_AX_SHFT		7			/* ABC low	    */
+#define MD_PDIR_AX_MASK		(1 << 7)
+#define MD_PDIR_AX		(1 << 7)
+#define MD_PDIR_FINE_SHFT	12			/* ABC low	    */
+#define MD_PDIR_FINE_MASK	(1 << 12)
+#define MD_PDIR_FINE		(1 << 12)
+#define MD_PDIR_OCT_SHFT	13			/* A low	    */
+#define MD_PDIR_OCT_MASK	(7 << 13)
+#define MD_PDIR_STATE_SHFT	13			/* BC low	    */
+#define MD_PDIR_STATE_MASK	(7 << 13)
+#define MD_PDIR_ONECNT_SHFT	16			/* BC low	    */
+#define MD_PDIR_ONECNT_MASK	(0x3f << 16)
+#define MD_PDIR_PTR_SHFT	22			/* C low	    */
+#define MD_PDIR_PTR_MASK	(UINT64_CAST 0x7ff << 22)
+#define MD_PDIR_VECMSB_SHFT	22			/* AB low	    */
+#define MD_PDIR_VECMSB_BITMASK	0x3ffffff
+#define MD_PDIR_VECMSB_BITSHFT	27
+#define MD_PDIR_VECMSB_MASK	(UINT64_CAST MD_PDIR_VECMSB_BITMASK << 22)
+#define MD_PDIR_CWOFF_SHFT	7			/* C high	    */
+#define MD_PDIR_CWOFF_MASK	(7 << 7)
+#define MD_PDIR_VECLSB_SHFT	10			/* AB high	    */
+#define MD_PDIR_VECLSB_BITMASK	(UINT64_CAST 0x3fffffffff)
+#define MD_PDIR_VECLSB_BITSHFT	0
+#define MD_PDIR_VECLSB_MASK	(MD_PDIR_VECLSB_BITMASK << 10)
+
+/*
+ * Directory initialization values
+ */
+
+#define MD_PDIR_INIT_LO		(MD_DIR_UNOWNED << MD_PDIR_STATE_SHFT | \
+				 MD_PDIR_AX)
+#define MD_PDIR_INIT_HI		0
+#define MD_PDIR_INIT_PROT	(MD_PROT_RW << MD_PPROT_IO_SHFT | \
+				 MD_PROT_RW << MD_PPROT_SHFT)
+
+/*
+ * Standard SIMM directory entry shifts and masks.  Each is valid only in the
+ * context(s) indicated, where A and C indicate the directory entry format
+ * as shown, and low and/or high indicates which double-word of the entry.
+ *
+ * Format A:  STATE == shared
+ * Format C:  STATE != shared
+ */
+
+#define MD_SDIR_MASK		0xffff			/* Whole entry	    */
+#define MD_SDIR_ECC_SHFT	0			/* AC low or high   */
+#define MD_SDIR_ECC_MASK	0x1f
+#define MD_SDIR_PRIO_SHFT	6			/* AC low	    */
+#define MD_SDIR_PRIO_MASK	(1 << 6)
+#define MD_SDIR_AX_SHFT		5			/* AC low	    */
+#define MD_SDIR_AX_MASK		(1 << 5)
+#define MD_SDIR_AX		(1 << 5)
+#define MD_SDIR_STATE_SHFT	7			/* AC low	    */
+#define MD_SDIR_STATE_MASK	(7 << 7)
+#define MD_SDIR_PTR_SHFT	10			/* C low	    */
+#define MD_SDIR_PTR_MASK	(0x3f << 10)
+#define MD_SDIR_CWOFF_SHFT	5			/* C high	    */
+#define MD_SDIR_CWOFF_MASK	(7 << 5)
+#define MD_SDIR_VECMSB_SHFT	11			/* A low	    */
+#define MD_SDIR_VECMSB_BITMASK	0x1f
+#define MD_SDIR_VECMSB_BITSHFT	7
+#define MD_SDIR_VECMSB_MASK	(MD_SDIR_VECMSB_BITMASK << 11)
+#define MD_SDIR_VECLSB_SHFT	5			/* A high	    */
+#define MD_SDIR_VECLSB_BITMASK	0x7ff
+#define MD_SDIR_VECLSB_BITSHFT	0
+#define MD_SDIR_VECLSB_MASK	(MD_SDIR_VECLSB_BITMASK << 5)
+
+/*
+ * Directory initialization values
+ */
+
+#define MD_SDIR_INIT_LO		(MD_DIR_UNOWNED << MD_SDIR_STATE_SHFT | \
+				 MD_SDIR_AX)
+#define MD_SDIR_INIT_HI		0
+#define MD_SDIR_INIT_PROT	(MD_PROT_RW << MD_SPROT_SHFT)
+
+/* Protection and migration field values */
+
+#define MD_PROT_RW		(UINT64_CAST 0x6)
+#define MD_PROT_RO		(UINT64_CAST 0x3)
+#define MD_PROT_NO		(UINT64_CAST 0x0)
+#define MD_PROT_BAD		(UINT64_CAST 0x5)
+
+/* Premium SIMM protection entry shifts and masks. */
+
+#define MD_PPROT_SHFT		0			/* Prot. field	    */
+#define MD_PPROT_MASK		7
+#define MD_PPROT_MIGMD_SHFT	3			/* Migration mode   */
+#define MD_PPROT_MIGMD_MASK	(3 << 3)
+#define MD_PPROT_REFCNT_SHFT	5			/* Reference count  */
+#define MD_PPROT_REFCNT_WIDTH	0x7ffff
+#define MD_PPROT_REFCNT_MASK	(MD_PPROT_REFCNT_WIDTH << 5)
+
+#define MD_PPROT_IO_SHFT	45			/* I/O Prot field   */
+#define MD_PPROT_IO_MASK	(UINT64_CAST 7 << 45)
+
+/* Standard SIMM protection entry shifts and masks. */
+
+#define MD_SPROT_SHFT		0			/* Prot. field	    */
+#define MD_SPROT_MASK		7
+#define MD_SPROT_MIGMD_SHFT	3			/* Migration mode   */
+#define MD_SPROT_MIGMD_MASK	(3 << 3)
+#define MD_SPROT_REFCNT_SHFT	5			/* Reference count  */
+#define MD_SPROT_REFCNT_WIDTH	0x7ff
+#define MD_SPROT_REFCNT_MASK	(MD_SPROT_REFCNT_WIDTH << 5)
+
+/* Migration modes used in protection entries */
+
+#define MD_PROT_MIGMD_IREL	(UINT64_CAST 0x3 << 3)
+#define MD_PROT_MIGMD_IABS	(UINT64_CAST 0x2 << 3)
+#define MD_PROT_MIGMD_PREL	(UINT64_CAST 0x1 << 3)
+#define MD_PROT_MIGMD_OFF	(UINT64_CAST 0x0 << 3)
+
+
+/*
+ * Operations on page migration threshold register
+ */
+
+#ifndef __ASSEMBLY__
+
+/*
+ * LED register macros
+ */
+
+#define CPU_LED_ADDR(_nasid, _slice)					   \
+	(private.p_sn00 ?						   \
+	 REMOTE_HUB_ADDR((_nasid), MD_UREG1_0 + ((_slice) << 5)) :	   \
+	 REMOTE_HUB_ADDR((_nasid), MD_LED0    + ((_slice) << 3)))
+
+#define SET_CPU_LEDS(_nasid, _slice,  _val)				   \
+	(HUB_S(CPU_LED_ADDR(_nasid, _slice), (_val)))
+
+#define SET_MY_LEDS(_v)							   \
+	SET_CPU_LEDS(get_nasid(), get_slice(), (_v))
+
+/*
+ * Operations on Memory/Directory DIMM control register
+ */
+
+#define DIRTYPE_PREMIUM 1
+#define DIRTYPE_STANDARD 0
+#define MD_MEMORY_CONFIG_DIR_TYPE_GET(region) (\
+	(REMOTE_HUB_L(region, MD_MEMORY_CONFIG) & MMC_DIR_PREMIUM_MASK) >> \
+	MMC_DIR_PREMIUM_SHFT)
+
+
+/*
+ * Operations on page migration count difference and absolute threshold
+ * registers
+ */
+
+#define MD_MIG_DIFF_THRESH_GET(region) ( \
+	REMOTE_HUB_L((region), MD_MIG_DIFF_THRESH) & \
+	MD_MIG_DIFF_THRES_VALUE_MASK)
+
+#define MD_MIG_DIFF_THRESH_SET(region, value) (				\
+	REMOTE_HUB_S((region), MD_MIG_DIFF_THRESH,			\
+		MD_MIG_DIFF_THRES_VALID_MASK | (value)))
+
+#define MD_MIG_DIFF_THRESH_DISABLE(region) (			\
+	REMOTE_HUB_S((region), MD_MIG_DIFF_THRESH,			\
+		REMOTE_HUB_L((region), MD_MIG_DIFF_THRESH)		\
+			     & ~MD_MIG_DIFF_THRES_VALID_MASK))
+
+#define MD_MIG_DIFF_THRESH_ENABLE(region) (			\
+	REMOTE_HUB_S((region), MD_MIG_DIFF_THRESH,			\
+		REMOTE_HUB_L((region), MD_MIG_DIFF_THRESH)		\
+			     | MD_MIG_DIFF_THRES_VALID_MASK))
+
+#define MD_MIG_DIFF_THRESH_IS_ENABLED(region) (				\
+	REMOTE_HUB_L((region), MD_MIG_DIFF_THRESH) &			\
+	       MD_MIG_DIFF_THRES_VALID_MASK)
+
+#define MD_MIG_VALUE_THRESH_GET(region) (				\
+	REMOTE_HUB_L((region), MD_MIG_VALUE_THRESH) &  \
+	MD_MIG_VALUE_THRES_VALUE_MASK)
+
+#define MD_MIG_VALUE_THRESH_SET(region, value) (			\
+	REMOTE_HUB_S((region), MD_MIG_VALUE_THRESH,			\
+		MD_MIG_VALUE_THRES_VALID_MASK | (value)))
+
+#define MD_MIG_VALUE_THRESH_DISABLE(region) (			\
+	REMOTE_HUB_S((region), MD_MIG_VALUE_THRESH,			\
+		REMOTE_HUB_L(region, MD_MIG_VALUE_THRESH)		\
+			     & ~MD_MIG_VALUE_THRES_VALID_MASK))
+
+#define MD_MIG_VALUE_THRESH_ENABLE(region) (			\
+	REMOTE_HUB_S((region), MD_MIG_VALUE_THRESH,			\
+		REMOTE_HUB_L((region), MD_MIG_VALUE_THRESH)		\
+			     | MD_MIG_VALUE_THRES_VALID_MASK))
+
+#define MD_MIG_VALUE_THRESH_IS_ENABLED(region) (			\
+	REMOTE_HUB_L((region), MD_MIG_VALUE_THRESH) &			 \
+	       MD_MIG_VALUE_THRES_VALID_MASK)
+
+/*
+ * Operations on page migration candidate register
+ */
+
+#define MD_MIG_CANDIDATE_GET(my_region_id) ( \
+	REMOTE_HUB_L((my_region_id), MD_MIG_CANDIDATE_CLR))
+
+#define MD_MIG_CANDIDATE_HWPFN(value) ((value) & MD_MIG_CANDIDATE_ADDR_MASK)
+
+#define MD_MIG_CANDIDATE_NODEID(value) ( \
+	((value) & MD_MIG_CANDIDATE_NODEID_MASK) >> MD_MIG_CANDIDATE_NODEID_SHFT)
+
+#define MD_MIG_CANDIDATE_TYPE(value) ( \
+	((value) & MD_MIG_CANDIDATE_TYPE_MASK) >> MD_MIG_CANDIDATE_TYPE_SHFT)
+
+#define MD_MIG_CANDIDATE_VALID(value) ( \
+	((value) & MD_MIG_CANDIDATE_VALID_MASK) >> MD_MIG_CANDIDATE_VALID_SHFT)
+
+/*
+ * Macros to retrieve fields in the protection entry
+ */
+
+/* for Premium SIMM */
+#define MD_PPROT_REFCNT_GET(value) ( \
+	((value) & MD_PPROT_REFCNT_MASK) >> MD_PPROT_REFCNT_SHFT)
+
+#define MD_PPROT_MIGMD_GET(value) ( \
+	((value) & MD_PPROT_MIGMD_MASK) >> MD_PPROT_MIGMD_SHFT)
+
+/* for Standard SIMM */
+#define MD_SPROT_REFCNT_GET(value) ( \
+	((value) & MD_SPROT_REFCNT_MASK) >> MD_SPROT_REFCNT_SHFT)
+
+#define MD_SPROT_MIGMD_GET(value) ( \
+	((value) & MD_SPROT_MIGMD_MASK) >> MD_SPROT_MIGMD_SHFT)
+
+/*
+ * Format of dir_error, mem_error, protocol_error and misc_error registers
+ */
+
+struct dir_error_reg {
+	u64	uce_vld:   1,	/*    63: valid directory uce	*/
+		ae_vld:	   1,	/*    62: valid dir prot ecc error */
+		ce_vld:	   1,	/*    61: valid correctable ECC err*/
+		rsvd1:	  19,	/* 60-42: reserved		*/
+		bad_prot:  3,	/* 41-39: encoding, bad access rights*/
+		bad_syn:   7,	/* 38-32: bad dir syndrome	*/
+		rsvd2:	   2,	/* 31-30: reserved		*/
+		hspec_addr:27,	/* 29-03: bddir space bad entry */
+		uce_ovr:   1,	/*     2: multiple dir uce's	*/
+		ae_ovr:	   1,	/*     1: multiple prot ecc errs*/
+		ce_ovr:	   1;	/*     0: multiple correctable errs */
+};
+
+typedef union md_dir_error {
+	u64	derr_reg;	/* the entire register		*/
+	struct dir_error_reg derr_fmt;	/* the register format		*/
+} md_dir_error_t;
+
+
+struct mem_error_reg {
+	u64	uce_vld:   1,	/*    63: valid memory uce	*/
+		ce_vld:	   1,	/*    62: valid correctable ECC err*/
+		rsvd1:	  22,	/* 61-40: reserved		*/
+		bad_syn:   8,	/* 39-32: bad mem ecc syndrome	*/
+		address:  29,	/* 31-03: bad entry pointer	*/
+		rsvd2:	   1,	/*     2: reserved		*/
+		uce_ovr:   1,	/*     1: multiple mem uce's	*/
+		ce_ovr:	   1;	/*     0: multiple correctable errs */
+};
+
+
+typedef union md_mem_error {
+	u64	merr_reg;	/* the entire register		*/
+	struct mem_error_reg  merr_fmt; /* format of the mem_error reg	*/
+} md_mem_error_t;
+
+
+struct proto_error_reg {
+	u64	valid:	   1,	/*    63: valid protocol error	*/
+		rsvd1:	   2,	/* 62-61: reserved		*/
+		initiator:11,	/* 60-50: id of request initiator*/
+		backoff:   2,	/* 49-48: backoff control	*/
+		msg_type:  8,	/* 47-40: type of request	*/
+		access:	   2,	/* 39-38: access rights of initiator*/
+		priority:  1,	/*    37: priority level of requestor*/
+		dir_state: 4,	/* 36-33: state of directory	*/
+		pointer_me:1,	/*    32: initiator same as dir ptr */
+		address:  29,	/* 31-03: request address	*/
+		rsvd2:	   2,	/* 02-01: reserved		*/
+		overrun:   1;	/*     0: multiple protocol errs */
+};
+
+typedef union md_proto_error {
+	u64	perr_reg;	/* the entire register		*/
+	struct proto_error_reg	perr_fmt; /* format of the register	*/
+} md_proto_error_t;
+
+
+struct md_sdir_high_fmt {
+	unsigned short sd_hi_bvec : 11,
+		       sd_hi_ecc  : 5;
+};
+
+
+typedef union md_sdir_high {
+	/* The 16 bits of standard directory, upper word */
+	unsigned short sd_hi_val;
+	struct	md_sdir_high_fmt sd_hi_fmt;
+}md_sdir_high_t;
+
+
+struct md_sdir_low_shared_fmt {
+	/* The meaning of lower directory, shared */
+	unsigned short	sds_lo_bvec  : 5,
+			sds_lo_unused: 1,
+			sds_lo_state : 3,
+			sds_lo_prio  : 1,
+			sds_lo_ax    : 1,
+			sds_lo_ecc   : 5;
+};
+
+struct md_sdir_low_exclusive_fmt {
+	/* The meaning of lower directory, exclusive */
+	unsigned short	sde_lo_ptr   : 6,
+			sde_lo_state : 3,
+			sde_lo_prio  : 1,
+			sde_lo_ax    : 1,
+			sde_lo_ecc   : 5;
+};
+
+
+typedef union md_sdir_low {
+	/* The 16 bits of standard directory, lower word */
+	unsigned short	sd_lo_val;
+	struct	md_sdir_low_exclusive_fmt sde_lo_fmt;
+	struct	md_sdir_low_shared_fmt sds_lo_fmt;
+}md_sdir_low_t;
+
+
+
+struct md_pdir_high_fmt {
+	u64	pd_hi_unused   : 16,
+		pd_hi_bvec     : 38,
+		pd_hi_unused1  : 3,
+		pd_hi_ecc      : 7;
+};
+
+
+typedef union md_pdir_high {
+	/* The 48 bits of standard directory, upper word */
+	u64	pd_hi_val;
+	struct md_pdir_high_fmt pd_hi_fmt;
+}md_pdir_high_t;
+
+
+struct md_pdir_low_shared_fmt {
+	/* The meaning of lower directory, shared */
+	u64	pds_lo_unused	: 16,
+		pds_lo_bvec	: 26,
+		pds_lo_cnt	:  6,
+		pds_lo_state	:  3,
+		pds_lo_ste	:  1,
+		pds_lo_prio	:  4,
+		pds_lo_ax	:  1,
+		pds_lo_ecc	:  7;
+};
+
+struct md_pdir_low_exclusive_fmt {
+	/* The meaning of lower directory, exclusive */
+	u64	pde_lo_unused	: 31,
+		pde_lo_ptr	: 11,
+		pde_lo_unused1	:  6,
+		pde_lo_state	:  3,
+		pde_lo_ste	:  1,
+		pde_lo_prio	:  4,
+		pde_lo_ax	:  1,
+		pde_lo_ecc	:  7;
+};
+
+
+typedef union md_pdir_loent {
+	/* The 48 bits of premium directory, lower word */
+	u64	pd_lo_val;
+	struct md_pdir_low_exclusive_fmt pde_lo_fmt;
+	struct md_pdir_low_shared_fmt	pds_lo_fmt;
+}md_pdir_low_t;
+
+
+/*
+ *   the following two "union" definitions and two
+ *   "struct" definitions are used in vmdump.c to
+ *   represent directory memory information.
+ */
+
+typedef union	md_dir_high	{
+	md_sdir_high_t	md_sdir_high;
+	md_pdir_high_t	md_pdir_high;
+} md_dir_high_t;
+
+typedef union	md_dir_low	{
+	md_sdir_low_t	md_sdir_low;
+	md_pdir_low_t	md_pdir_low;
+} md_dir_low_t;
+
+typedef struct	bddir_entry	{
+	md_dir_low_t	md_dir_low;
+	md_dir_high_t	md_dir_high;
+} bddir_entry_t;
+
+typedef struct	dir_mem_entry	{
+	u64		prcpf[MAX_REGIONS];
+	bddir_entry_t	directory_words[MD_PAGE_SIZE/CACHE_SLINE_SIZE];
+} dir_mem_entry_t;
+
+
+
+typedef union md_perf_sel {
+	u64	perf_sel_reg;
+	struct	{
+		u64	perf_rsvd : 60,
+			perf_en	  :  1,
+			perf_sel  :  3;
+	} perf_sel_bits;
+} md_perf_sel_t;
+
+typedef union md_perf_cnt {
+	u64	perf_cnt;
+	struct	{
+		u64	perf_rsvd : 44,
+			perf_cnt  : 20;
+	} perf_cnt_bits;
+} md_perf_cnt_t;
+
+
+#endif /* !__ASSEMBLY__ */
+
+
+#define DIR_ERROR_VALID_MASK	0xe000000000000000
+#define DIR_ERROR_VALID_SHFT	61
+#define DIR_ERROR_VALID_UCE	0x8000000000000000
+#define DIR_ERROR_VALID_AE	0x4000000000000000
+#define DIR_ERROR_VALID_CE	0x2000000000000000
+
+#define MEM_ERROR_VALID_MASK	0xc000000000000000
+#define MEM_ERROR_VALID_SHFT	62
+#define MEM_ERROR_VALID_UCE	0x8000000000000000
+#define MEM_ERROR_VALID_CE	0x4000000000000000
+
+#define PROTO_ERROR_VALID_MASK	0x8000000000000000
+
+#define MISC_ERROR_VALID_MASK	0x3ff
+
+/*
+ * Mask for hspec address that is stored in the dir error register.
+ * This represents bits 29 through 3.
+ */
+#define DIR_ERR_HSPEC_MASK	0x3ffffff8
+#define ERROR_HSPEC_MASK	0x3ffffff8
+#define ERROR_HSPEC_SHFT	3
+#define ERROR_ADDR_MASK		0xfffffff8
+#define ERROR_ADDR_SHFT		3
+
+/*
+ * MD_MISC_ERROR register defines.
+ */
+
+#define MMCE_VALID_MASK		0x3ff
+#define MMCE_ILL_MSG_SHFT	8
+#define MMCE_ILL_MSG_MASK	(UINT64_CAST 0x03 << MMCE_ILL_MSG_SHFT)
+#define MMCE_ILL_REV_SHFT	6
+#define MMCE_ILL_REV_MASK	(UINT64_CAST 0x03 << MMCE_ILL_REV_SHFT)
+#define MMCE_LONG_PACK_SHFT	4
+#define MMCE_LONG_PACK_MASK	(UINT64_CAST 0x03 << MMCE_lONG_PACK_SHFT)
+#define MMCE_SHORT_PACK_SHFT	2
+#define MMCE_SHORT_PACK_MASK	(UINT64_CAST 0x03 << MMCE_SHORT_PACK_SHFT)
+#define MMCE_BAD_DATA_SHFT	0
+#define MMCE_BAD_DATA_MASK	(UINT64_CAST 0x03 << MMCE_BAD_DATA_SHFT)
+
+
+#define MD_PERF_COUNTERS	6
+#define MD_PERF_SETS		6
+
+#define MEM_DIMM_MASK				0xe0000000
+#define MEM_DIMM_SHFT				29
+
+#endif /* _ASM_SN_SN0_HUBMD_H */
diff --git a/arch/mips/include/asm/sn/sn0/hubni.h b/arch/mips/include/asm/sn/sn0/hubni.h
new file mode 100644
index 000000000..b8253142c
--- /dev/null
+++ b/arch/mips/include/asm/sn/sn0/hubni.h
@@ -0,0 +1,263 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Derived from IRIX <sys/SN/SN0/hubni.h>, Revision 1.27.
+ *
+ * Copyright (C) 1992-1997, 1999 Silicon Graphics, Inc.
+ * Copyright (C) 1999 by Ralf Baechle
+ */
+#ifndef _ASM_SGI_SN0_HUBNI_H
+#define _ASM_SGI_SN0_HUBNI_H
+
+#ifndef __ASSEMBLY__
+#include <linux/types.h>
+#endif
+
+/*
+ * Hub Network Interface registers
+ *
+ * All registers in this file are subject to change until Hub chip tapeout.
+ */
+
+#define NI_BASE			0x600000
+#define NI_BASE_TABLES		0x630000
+
+#define NI_STATUS_REV_ID	0x600000 /* Hub network status, rev, and ID */
+#define NI_PORT_RESET		0x600008 /* Reset the network interface	    */
+#define NI_PROTECTION		0x600010 /* NI register access permissions  */
+#define NI_GLOBAL_PARMS		0x600018 /* LLP parameters		    */
+#define NI_SCRATCH_REG0		0x600100 /* Scratch register 0 (64 bits)    */
+#define NI_SCRATCH_REG1		0x600108 /* Scratch register 1 (64 bits)    */
+#define NI_DIAG_PARMS		0x600110 /* Parameters for diags	    */
+
+#define NI_VECTOR_PARMS		0x600200 /* Vector PIO routing parameters   */
+#define NI_VECTOR		0x600208 /* Vector PIO route		    */
+#define NI_VECTOR_DATA		0x600210 /* Vector PIO data		    */
+#define NI_VECTOR_STATUS	0x600300 /* Vector PIO return status	    */
+#define NI_RETURN_VECTOR	0x600308 /* Vector PIO return vector	    */
+#define NI_VECTOR_READ_DATA	0x600310 /* Vector PIO read data	    */
+#define NI_VECTOR_CLEAR		0x600380 /* Vector PIO read & clear status  */
+
+#define NI_IO_PROTECT		0x600400 /* PIO protection bits		    */
+#define NI_IO_PROT_OVRRD	0x600408 /* PIO protection bit override	    */
+
+#define NI_AGE_CPU0_MEMORY	0x600500 /* CPU 0 memory age control	    */
+#define NI_AGE_CPU0_PIO		0x600508 /* CPU 0 PIO age control	    */
+#define NI_AGE_CPU1_MEMORY	0x600510 /* CPU 1 memory age control	    */
+#define NI_AGE_CPU1_PIO		0x600518 /* CPU 1 PIO age control	    */
+#define NI_AGE_GBR_MEMORY	0x600520 /* GBR memory age control	    */
+#define NI_AGE_GBR_PIO		0x600528 /* GBR PIO age control		    */
+#define NI_AGE_IO_MEMORY	0x600530 /* IO memory age control	    */
+#define NI_AGE_IO_PIO		0x600538 /* IO PIO age control		    */
+#define NI_AGE_REG_MIN		NI_AGE_CPU0_MEMORY
+#define NI_AGE_REG_MAX		NI_AGE_IO_PIO
+
+#define NI_PORT_PARMS		0x608000 /* LLP Parameters		    */
+#define NI_PORT_ERROR		0x608008 /* LLP Errors			    */
+#define NI_PORT_ERROR_CLEAR	0x608088 /* Clear the error bits	    */
+
+#define NI_META_TABLE0		0x638000 /* First meta routing table entry  */
+#define NI_META_TABLE(_x)	(NI_META_TABLE0 + (8 * (_x)))
+#define NI_META_ENTRIES		32
+
+#define NI_LOCAL_TABLE0		0x638100 /* First local routing table entry */
+#define NI_LOCAL_TABLE(_x)	(NI_LOCAL_TABLE0 + (8 * (_x)))
+#define NI_LOCAL_ENTRIES	16
+
+/*
+ * NI_STATUS_REV_ID mask and shift definitions
+ * Have to use UINT64_CAST instead of 'L' suffix, for assembler.
+ */
+
+#define NSRI_8BITMODE_SHFT	30
+#define NSRI_8BITMODE_MASK	(UINT64_CAST 0x1 << 30)
+#define NSRI_LINKUP_SHFT	29
+#define NSRI_LINKUP_MASK	(UINT64_CAST 0x1 << 29)
+#define NSRI_DOWNREASON_SHFT	28		/* 0=failed, 1=never came   */
+#define NSRI_DOWNREASON_MASK	(UINT64_CAST 0x1 << 28) /*    out of reset. */
+#define NSRI_MORENODES_SHFT	18
+#define NSRI_MORENODES_MASK	(UINT64_CAST 1 << 18)	/* Max. # of nodes  */
+#define	 MORE_MEMORY		0
+#define	 MORE_NODES		1
+#define NSRI_REGIONSIZE_SHFT	17
+#define NSRI_REGIONSIZE_MASK	(UINT64_CAST 1 << 17)	/* Granularity	    */
+#define	 REGIONSIZE_FINE	1
+#define	 REGIONSIZE_COARSE	0
+#define NSRI_NODEID_SHFT	8
+#define NSRI_NODEID_MASK	(UINT64_CAST 0x1ff << 8)/* Node (Hub) ID    */
+#define NSRI_REV_SHFT		4
+#define NSRI_REV_MASK		(UINT64_CAST 0xf << 4)	/* Chip Revision    */
+#define NSRI_CHIPID_SHFT	0
+#define NSRI_CHIPID_MASK	(UINT64_CAST 0xf)	/* Chip type ID	    */
+
+/*
+ * In fine mode, each node is a region.	 In coarse mode, there are
+ * eight nodes per region.
+ */
+#define NASID_TO_FINEREG_SHFT	0
+#define NASID_TO_COARSEREG_SHFT 3
+
+/* NI_PORT_RESET mask definitions */
+
+#define NPR_PORTRESET		(UINT64_CAST 1 << 7)	/* Send warm reset  */
+#define NPR_LINKRESET		(UINT64_CAST 1 << 1)	/* Send link reset  */
+#define NPR_LOCALRESET		(UINT64_CAST 1)		/* Reset entire hub */
+
+/* NI_PROTECTION mask and shift definitions */
+
+#define NPROT_RESETOK		(UINT64_CAST 1)
+
+/* NI_GLOBAL_PARMS mask and shift definitions */
+
+#define NGP_MAXRETRY_SHFT	48		/* Maximum retries	    */
+#define NGP_MAXRETRY_MASK	(UINT64_CAST 0x3ff << 48)
+#define NGP_TAILTOWRAP_SHFT	32		/* Tail timeout wrap	    */
+#define NGP_TAILTOWRAP_MASK	(UINT64_CAST 0xffff << 32)
+
+#define NGP_CREDITTOVAL_SHFT	16		/* Tail timeout wrap	    */
+#define NGP_CREDITTOVAL_MASK	(UINT64_CAST 0xf << 16)
+#define NGP_TAILTOVAL_SHFT	4		/* Tail timeout value	    */
+#define NGP_TAILTOVAL_MASK	(UINT64_CAST 0xf << 4)
+
+/* NI_DIAG_PARMS mask and shift definitions */
+
+#define NDP_PORTTORESET		(UINT64_CAST 1 << 18)	/* Port tmout reset */
+#define NDP_LLP8BITMODE		(UINT64_CAST 1 << 12)	/* LLP 8-bit mode   */
+#define NDP_PORTDISABLE		(UINT64_CAST 1 <<  6)	/* Port disable	    */
+#define NDP_SENDERROR		(UINT64_CAST 1)		/* Send data error  */
+
+/*
+ * NI_VECTOR_PARMS mask and shift definitions.
+ * TYPE may be any of the first four PIOTYPEs defined under NI_VECTOR_STATUS.
+ */
+
+#define NVP_PIOID_SHFT		40
+#define NVP_PIOID_MASK		(UINT64_CAST 0x3ff << 40)
+#define NVP_WRITEID_SHFT	32
+#define NVP_WRITEID_MASK	(UINT64_CAST 0xff << 32)
+#define NVP_ADDRESS_MASK	(UINT64_CAST 0xffff8)	/* Bits 19:3	    */
+#define NVP_TYPE_SHFT		0
+#define NVP_TYPE_MASK		(UINT64_CAST 0x3)
+
+/* NI_VECTOR_STATUS mask and shift definitions */
+
+#define NVS_VALID		(UINT64_CAST 1 << 63)
+#define NVS_OVERRUN		(UINT64_CAST 1 << 62)
+#define NVS_TARGET_SHFT		51
+#define NVS_TARGET_MASK		(UINT64_CAST 0x3ff << 51)
+#define NVS_PIOID_SHFT		40
+#define NVS_PIOID_MASK		(UINT64_CAST 0x3ff << 40)
+#define NVS_WRITEID_SHFT	32
+#define NVS_WRITEID_MASK	(UINT64_CAST 0xff << 32)
+#define NVS_ADDRESS_MASK	(UINT64_CAST 0xfffffff8)   /* Bits 31:3	    */
+#define NVS_TYPE_SHFT		0
+#define NVS_TYPE_MASK		(UINT64_CAST 0x7)
+#define NVS_ERROR_MASK		(UINT64_CAST 0x4)  /* bit set means error */
+
+
+#define	 PIOTYPE_READ		0	/* VECTOR_PARMS and VECTOR_STATUS   */
+#define	 PIOTYPE_WRITE		1	/* VECTOR_PARMS and VECTOR_STATUS   */
+#define	 PIOTYPE_UNDEFINED	2	/* VECTOR_PARMS and VECTOR_STATUS   */
+#define	 PIOTYPE_EXCHANGE	3	/* VECTOR_PARMS and VECTOR_STATUS   */
+#define	 PIOTYPE_ADDR_ERR	4	/* VECTOR_STATUS only		    */
+#define	 PIOTYPE_CMD_ERR	5	/* VECTOR_STATUS only		    */
+#define	 PIOTYPE_PROT_ERR	6	/* VECTOR_STATUS only		    */
+#define	 PIOTYPE_UNKNOWN	7	/* VECTOR_STATUS only		    */
+
+/* NI_AGE_XXX mask and shift definitions */
+
+#define NAGE_VCH_SHFT		10
+#define NAGE_VCH_MASK		(UINT64_CAST 3 << 10)
+#define NAGE_CC_SHFT		8
+#define NAGE_CC_MASK		(UINT64_CAST 3 << 8)
+#define NAGE_AGE_SHFT		0
+#define NAGE_AGE_MASK		(UINT64_CAST 0xff)
+#define NAGE_MASK		(NAGE_VCH_MASK | NAGE_CC_MASK | NAGE_AGE_MASK)
+
+#define	 VCHANNEL_A		0
+#define	 VCHANNEL_B		1
+#define	 VCHANNEL_ANY		2
+
+/* NI_PORT_PARMS mask and shift definitions */
+
+#define NPP_NULLTO_SHFT		10
+#define NPP_NULLTO_MASK		(UINT64_CAST 0x3f << 16)
+#define NPP_MAXBURST_SHFT	0
+#define NPP_MAXBURST_MASK	(UINT64_CAST 0x3ff)
+#define NPP_RESET_DFLT_HUB20	((UINT64_CAST 1	    << NPP_NULLTO_SHFT) | \
+				 (UINT64_CAST 0x3f0 << NPP_MAXBURST_SHFT))
+#define NPP_RESET_DEFAULTS	((UINT64_CAST 6	    << NPP_NULLTO_SHFT) | \
+				 (UINT64_CAST 0x3f0 << NPP_MAXBURST_SHFT))
+
+
+/* NI_PORT_ERROR mask and shift definitions */
+
+#define NPE_LINKRESET		(UINT64_CAST 1 << 37)
+#define NPE_INTERNALERROR	(UINT64_CAST 1 << 36)
+#define NPE_BADMESSAGE		(UINT64_CAST 1 << 35)
+#define NPE_BADDEST		(UINT64_CAST 1 << 34)
+#define NPE_FIFOOVERFLOW	(UINT64_CAST 1 << 33)
+#define NPE_CREDITTO_SHFT	28
+#define NPE_CREDITTO_MASK	(UINT64_CAST 0xf << 28)
+#define NPE_TAILTO_SHFT		24
+#define NPE_TAILTO_MASK		(UINT64_CAST 0xf << 24)
+#define NPE_RETRYCOUNT_SHFT	16
+#define NPE_RETRYCOUNT_MASK	(UINT64_CAST 0xff << 16)
+#define NPE_CBERRCOUNT_SHFT	8
+#define NPE_CBERRCOUNT_MASK	(UINT64_CAST 0xff << 8)
+#define NPE_SNERRCOUNT_SHFT	0
+#define NPE_SNERRCOUNT_MASK	(UINT64_CAST 0xff << 0)
+#define NPE_MASK		0x3effffffff
+
+#define NPE_COUNT_MAX		0xff
+
+#define NPE_FATAL_ERRORS	(NPE_LINKRESET | NPE_INTERNALERROR |	\
+				 NPE_BADMESSAGE | NPE_BADDEST |		\
+				 NPE_FIFOOVERFLOW | NPE_CREDITTO_MASK | \
+				 NPE_TAILTO_MASK)
+
+/* NI_META_TABLE mask and shift definitions */
+
+#define NMT_EXIT_PORT_MASK (UINT64_CAST 0xf)
+
+/* NI_LOCAL_TABLE mask and shift definitions */
+
+#define NLT_EXIT_PORT_MASK (UINT64_CAST 0xf)
+
+#ifndef __ASSEMBLY__
+
+typedef union	hubni_port_error_u {
+	u64	nipe_reg_value;
+	struct {
+	    u64 nipe_rsvd:	26,	/* unused */
+		nipe_lnk_reset:	 1,	/* link reset */
+		nipe_intl_err:	 1,	/* internal error */
+		nipe_bad_msg:	 1,	/* bad message */
+		nipe_bad_dest:	 1,	/* bad dest	*/
+		nipe_fifo_ovfl:	 1,	/* fifo overflow */
+		nipe_rsvd1:	 1,	/* unused */
+		nipe_credit_to:	 4,	/* credit timeout */
+		nipe_tail_to:	 4,	/* tail timeout */
+		nipe_retry_cnt:	 8,	/* retry error count */
+		nipe_cb_cnt:	 8,	/* checkbit error count */
+		nipe_sn_cnt:	 8;	/* sequence number count */
+	} nipe_fields_s;
+} hubni_port_error_t;
+
+#define NI_LLP_RETRY_MAX	0xff
+#define NI_LLP_CB_MAX		0xff
+#define NI_LLP_SN_MAX		0xff
+
+static inline int get_region_shift(void)
+{
+	if (LOCAL_HUB_L(NI_STATUS_REV_ID) & NSRI_REGIONSIZE_MASK)
+		return NASID_TO_FINEREG_SHFT;
+
+	return NASID_TO_COARSEREG_SHFT;
+}
+
+#endif /* !__ASSEMBLY__ */
+
+#endif /* _ASM_SGI_SN0_HUBNI_H */
diff --git a/arch/mips/include/asm/sn/sn0/hubpi.h b/arch/mips/include/asm/sn/sn0/hubpi.h
new file mode 100644
index 000000000..7b8365591
--- /dev/null
+++ b/arch/mips/include/asm/sn/sn0/hubpi.h
@@ -0,0 +1,409 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Derived from IRIX <sys/SN/SN0/hubpi.h>, revision 1.28.
+ *
+ * Copyright (C) 1992 - 1997, 1999 Silicon Graphics, Inc.
+ * Copyright (C) 1999 by Ralf Baechle
+ */
+#ifndef _ASM_SN_SN0_HUBPI_H
+#define _ASM_SN_SN0_HUBPI_H
+
+#include <linux/types.h>
+
+/*
+ * Hub I/O interface registers
+ *
+ * All registers in this file are subject to change until Hub chip tapeout.
+ * All register "addresses" are actually offsets.  Use the LOCAL_HUB
+ * or REMOTE_HUB macros to synthesize an actual address
+ */
+
+#define PI_BASE			0x000000
+
+/* General protection and control registers */
+
+#define PI_CPU_PROTECT		0x000000 /* CPU Protection		    */
+#define PI_PROT_OVERRD		0x000008 /* Clear CPU Protection bit	    */
+#define PI_IO_PROTECT		0x000010 /* Interrupt Pending Protection    */
+#define PI_REGION_PRESENT	0x000018 /* Indicates whether region exists */
+#define PI_CPU_NUM		0x000020 /* CPU Number ID		    */
+#define PI_CALIAS_SIZE		0x000028 /* Cached Alias Size		    */
+#define PI_MAX_CRB_TIMEOUT	0x000030 /* Maximum Timeout for CRB	    */
+#define PI_CRB_SFACTOR		0x000038 /* Scale factor for CRB timeout    */
+
+/* CALIAS values */
+#define PI_CALIAS_SIZE_0	0
+#define PI_CALIAS_SIZE_4K	1
+#define PI_CALIAS_SIZE_8K	2
+#define PI_CALIAS_SIZE_16K	3
+#define PI_CALIAS_SIZE_32K	4
+#define PI_CALIAS_SIZE_64K	5
+#define PI_CALIAS_SIZE_128K	6
+#define PI_CALIAS_SIZE_256K	7
+#define PI_CALIAS_SIZE_512K	8
+#define PI_CALIAS_SIZE_1M	9
+#define PI_CALIAS_SIZE_2M	10
+#define PI_CALIAS_SIZE_4M	11
+#define PI_CALIAS_SIZE_8M	12
+#define PI_CALIAS_SIZE_16M	13
+#define PI_CALIAS_SIZE_32M	14
+#define PI_CALIAS_SIZE_64M	15
+
+/* Processor control and status checking */
+
+#define PI_CPU_PRESENT_A	0x000040 /* CPU Present A		    */
+#define PI_CPU_PRESENT_B	0x000048 /* CPU Present B		    */
+#define PI_CPU_ENABLE_A		0x000050 /* CPU Enable A		    */
+#define PI_CPU_ENABLE_B		0x000058 /* CPU Enable B		    */
+#define PI_REPLY_LEVEL		0x000060 /* Reply Level			    */
+#define PI_HARDRESET_BIT	0x020068 /* Bit cleared by s/w on SR	    */
+#define PI_NMI_A		0x000070 /* NMI to CPU A		    */
+#define PI_NMI_B		0x000078 /* NMI to CPU B		    */
+#define PI_NMI_OFFSET		(PI_NMI_B - PI_NMI_A)
+#define PI_SOFTRESET		0x000080 /* Softreset (to both CPUs)	    */
+
+/* Regular Interrupt register checking.	 */
+
+#define PI_INT_PEND_MOD		0x000090 /* Write to set pending ints	    */
+#define PI_INT_PEND0		0x000098 /* Read to get pending ints	    */
+#define PI_INT_PEND1		0x0000a0 /* Read to get pending ints	    */
+#define PI_INT_MASK0_A		0x0000a8 /* Interrupt Mask 0 for CPU A	    */
+#define PI_INT_MASK1_A		0x0000b0 /* Interrupt Mask 1 for CPU A	    */
+#define PI_INT_MASK0_B		0x0000b8 /* Interrupt Mask 0 for CPU B	    */
+#define PI_INT_MASK1_B		0x0000c0 /* Interrupt Mask 1 for CPU B	    */
+
+#define PI_INT_MASK_OFFSET	0x10	 /* Offset from A to B		    */
+
+/* Crosscall interrupts */
+
+#define PI_CC_PEND_SET_A	0x0000c8 /* CC Interrupt Pending Set, CPU A */
+#define PI_CC_PEND_SET_B	0x0000d0 /* CC Interrupt Pending Set, CPU B */
+#define PI_CC_PEND_CLR_A	0x0000d8 /* CC Interrupt Pending Clr, CPU A */
+#define PI_CC_PEND_CLR_B	0x0000e0 /* CC Interrupt Pending Clr, CPU B */
+#define PI_CC_MASK		0x0000e8 /* CC Interrupt mask		    */
+
+#define PI_INT_SET_OFFSET	0x08	 /* Offset from A to B		    */
+
+/* Realtime Counter and Profiler control registers */
+
+#define PI_RT_COUNT		0x030100 /* Real Time Counter		    */
+#define PI_RT_COMPARE_A		0x000108 /* Real Time Compare A		    */
+#define PI_RT_COMPARE_B		0x000110 /* Real Time Compare B		    */
+#define PI_PROFILE_COMPARE	0x000118 /* L5 int to both cpus when == RTC */
+#define PI_RT_PEND_A		0x000120 /* Set if RT int for A pending	    */
+#define PI_RT_PEND_B		0x000128 /* Set if RT int for B pending	    */
+#define PI_PROF_PEND_A		0x000130 /* Set if Prof int for A pending   */
+#define PI_PROF_PEND_B		0x000138 /* Set if Prof int for B pending   */
+#define PI_RT_EN_A		0x000140 /* RT int for CPU A enable	    */
+#define PI_RT_EN_B		0x000148 /* RT int for CPU B enable	    */
+#define PI_PROF_EN_A		0x000150 /* PROF int for CPU A enable	    */
+#define PI_PROF_EN_B		0x000158 /* PROF int for CPU B enable	    */
+#define PI_RT_LOCAL_CTRL	0x000160 /* RT control register		    */
+#define PI_RT_FILTER_CTRL	0x000168 /* GCLK Filter control register    */
+
+#define PI_COUNT_OFFSET		0x08	 /* A to B offset for all counts    */
+
+/* Built-In Self Test support */
+
+#define PI_BIST_WRITE_DATA	0x000200 /* BIST write data		    */
+#define PI_BIST_READ_DATA	0x000208 /* BIST read data		    */
+#define PI_BIST_COUNT_TARG	0x000210 /* BIST Count and Target	    */
+#define PI_BIST_READY		0x000218 /* BIST Ready indicator	    */
+#define PI_BIST_SHIFT_LOAD	0x000220 /* BIST control		    */
+#define PI_BIST_SHIFT_UNLOAD	0x000228 /* BIST control		    */
+#define PI_BIST_ENTER_RUN	0x000230 /* BIST control		    */
+
+/* Graphics control registers */
+
+#define PI_GFX_PAGE_A		0x000300 /* Graphics page A		    */
+#define PI_GFX_CREDIT_CNTR_A	0x000308 /* Graphics credit counter A	    */
+#define PI_GFX_BIAS_A		0x000310 /* Graphics bias A		    */
+#define PI_GFX_INT_CNTR_A	0x000318 /* Graphics interrupt counter A    */
+#define PI_GFX_INT_CMP_A	0x000320 /* Graphics interrupt comparator A */
+#define PI_GFX_PAGE_B		0x000328 /* Graphics page B		    */
+#define PI_GFX_CREDIT_CNTR_B	0x000330 /* Graphics credit counter B	    */
+#define PI_GFX_BIAS_B		0x000338 /* Graphics bias B		    */
+#define PI_GFX_INT_CNTR_B	0x000340 /* Graphics interrupt counter B    */
+#define PI_GFX_INT_CMP_B	0x000348 /* Graphics interrupt comparator B */
+
+#define PI_GFX_OFFSET		(PI_GFX_PAGE_B - PI_GFX_PAGE_A)
+#define PI_GFX_PAGE_ENABLE	0x0000010000000000LL
+
+/* Error and timeout registers */
+#define PI_ERR_INT_PEND		0x000400 /* Error Interrupt Pending	    */
+#define PI_ERR_INT_MASK_A	0x000408 /* Error Interrupt mask for CPU A  */
+#define PI_ERR_INT_MASK_B	0x000410 /* Error Interrupt mask for CPU B  */
+#define PI_ERR_STACK_ADDR_A	0x000418 /* Error stack address for CPU A   */
+#define PI_ERR_STACK_ADDR_B	0x000420 /* Error stack address for CPU B   */
+#define PI_ERR_STACK_SIZE	0x000428 /* Error Stack Size		    */
+#define PI_ERR_STATUS0_A	0x000430 /* Error Status 0A		    */
+#define PI_ERR_STATUS0_A_RCLR	0x000438 /* Error Status 0A clear on read   */
+#define PI_ERR_STATUS1_A	0x000440 /* Error Status 1A		    */
+#define PI_ERR_STATUS1_A_RCLR	0x000448 /* Error Status 1A clear on read   */
+#define PI_ERR_STATUS0_B	0x000450 /* Error Status 0B		    */
+#define PI_ERR_STATUS0_B_RCLR	0x000458 /* Error Status 0B clear on read   */
+#define PI_ERR_STATUS1_B	0x000460 /* Error Status 1B		    */
+#define PI_ERR_STATUS1_B_RCLR	0x000468 /* Error Status 1B clear on read   */
+#define PI_SPOOL_CMP_A		0x000470 /* Spool compare for CPU A	    */
+#define PI_SPOOL_CMP_B		0x000478 /* Spool compare for CPU B	    */
+#define PI_CRB_TIMEOUT_A	0x000480 /* Timed out CRB entries for A	    */
+#define PI_CRB_TIMEOUT_B	0x000488 /* Timed out CRB entries for B	    */
+#define PI_SYSAD_ERRCHK_EN	0x000490 /* Enables SYSAD error checking    */
+#define PI_BAD_CHECK_BIT_A	0x000498 /* Force SYSAD check bit error	    */
+#define PI_BAD_CHECK_BIT_B	0x0004a0 /* Force SYSAD check bit error	    */
+#define PI_NACK_CNT_A		0x0004a8 /* Consecutive NACK counter	    */
+#define PI_NACK_CNT_B		0x0004b0 /*	"	" for CPU B	    */
+#define PI_NACK_CMP		0x0004b8 /* NACK count compare		    */
+#define PI_STACKADDR_OFFSET	(PI_ERR_STACK_ADDR_B - PI_ERR_STACK_ADDR_A)
+#define PI_ERRSTAT_OFFSET	(PI_ERR_STATUS0_B - PI_ERR_STATUS0_A)
+#define PI_RDCLR_OFFSET		(PI_ERR_STATUS0_A_RCLR - PI_ERR_STATUS0_A)
+
+/* Bits in PI_ERR_INT_PEND */
+#define PI_ERR_SPOOL_CMP_B	0x00000001	/* Spool end hit high water */
+#define PI_ERR_SPOOL_CMP_A	0x00000002
+#define PI_ERR_SPUR_MSG_B	0x00000004	/* Spurious message intr.   */
+#define PI_ERR_SPUR_MSG_A	0x00000008
+#define PI_ERR_WRB_TERR_B	0x00000010	/* WRB TERR		    */
+#define PI_ERR_WRB_TERR_A	0x00000020
+#define PI_ERR_WRB_WERR_B	0x00000040	/* WRB WERR		    */
+#define PI_ERR_WRB_WERR_A	0x00000080
+#define PI_ERR_SYSSTATE_B	0x00000100	/* SysState parity error    */
+#define PI_ERR_SYSSTATE_A	0x00000200
+#define PI_ERR_SYSAD_DATA_B	0x00000400	/* SysAD data parity error  */
+#define PI_ERR_SYSAD_DATA_A	0x00000800
+#define PI_ERR_SYSAD_ADDR_B	0x00001000	/* SysAD addr parity error  */
+#define PI_ERR_SYSAD_ADDR_A	0x00002000
+#define PI_ERR_SYSCMD_DATA_B	0x00004000	/* SysCmd data parity error */
+#define PI_ERR_SYSCMD_DATA_A	0x00008000
+#define PI_ERR_SYSCMD_ADDR_B	0x00010000	/* SysCmd addr parity error */
+#define PI_ERR_SYSCMD_ADDR_A	0x00020000
+#define PI_ERR_BAD_SPOOL_B	0x00040000	/* Error spooling to memory */
+#define PI_ERR_BAD_SPOOL_A	0x00080000
+#define PI_ERR_UNCAC_UNCORR_B	0x00100000	/* Uncached uncorrectable   */
+#define PI_ERR_UNCAC_UNCORR_A	0x00200000
+#define PI_ERR_SYSSTATE_TAG_B	0x00400000	/* SysState tag parity error */
+#define PI_ERR_SYSSTATE_TAG_A	0x00800000
+#define PI_ERR_MD_UNCORR	0x01000000	/* Must be cleared in MD    */
+
+#define PI_ERR_CLEAR_ALL_A	0x00aaaaaa
+#define PI_ERR_CLEAR_ALL_B	0x00555555
+
+
+/*
+ * The following three macros define all possible error int pends.
+ */
+
+#define PI_FATAL_ERR_CPU_A	(PI_ERR_SYSSTATE_TAG_A	| \
+				 PI_ERR_BAD_SPOOL_A	| \
+				 PI_ERR_SYSCMD_ADDR_A	| \
+				 PI_ERR_SYSCMD_DATA_A	| \
+				 PI_ERR_SYSAD_ADDR_A	| \
+				 PI_ERR_SYSAD_DATA_A	| \
+				 PI_ERR_SYSSTATE_A)
+
+#define PI_MISC_ERR_CPU_A	(PI_ERR_UNCAC_UNCORR_A	| \
+				 PI_ERR_WRB_WERR_A	| \
+				 PI_ERR_WRB_TERR_A	| \
+				 PI_ERR_SPUR_MSG_A	| \
+				 PI_ERR_SPOOL_CMP_A)
+
+#define PI_FATAL_ERR_CPU_B	(PI_ERR_SYSSTATE_TAG_B	| \
+				 PI_ERR_BAD_SPOOL_B	| \
+				 PI_ERR_SYSCMD_ADDR_B	| \
+				 PI_ERR_SYSCMD_DATA_B	| \
+				 PI_ERR_SYSAD_ADDR_B	| \
+				 PI_ERR_SYSAD_DATA_B	| \
+				 PI_ERR_SYSSTATE_B)
+
+#define PI_MISC_ERR_CPU_B	(PI_ERR_UNCAC_UNCORR_B	| \
+				 PI_ERR_WRB_WERR_B	| \
+				 PI_ERR_WRB_TERR_B	| \
+				 PI_ERR_SPUR_MSG_B	| \
+				 PI_ERR_SPOOL_CMP_B)
+
+#define PI_ERR_GENERIC	(PI_ERR_MD_UNCORR)
+
+/*
+ * Error types for PI_ERR_STATUS0_[AB] and error stack:
+ * Use the write types if WRBRRB is 1 else use the read types
+ */
+
+/* Fields in PI_ERR_STATUS0_[AB] */
+#define PI_ERR_ST0_TYPE_MASK	0x0000000000000007
+#define PI_ERR_ST0_TYPE_SHFT	0
+#define PI_ERR_ST0_REQNUM_MASK	0x0000000000000038
+#define PI_ERR_ST0_REQNUM_SHFT	3
+#define PI_ERR_ST0_SUPPL_MASK	0x000000000001ffc0
+#define PI_ERR_ST0_SUPPL_SHFT	6
+#define PI_ERR_ST0_CMD_MASK	0x0000000001fe0000
+#define PI_ERR_ST0_CMD_SHFT	17
+#define PI_ERR_ST0_ADDR_MASK	0x3ffffffffe000000
+#define PI_ERR_ST0_ADDR_SHFT	25
+#define PI_ERR_ST0_OVERRUN_MASK 0x4000000000000000
+#define PI_ERR_ST0_OVERRUN_SHFT 62
+#define PI_ERR_ST0_VALID_MASK	0x8000000000000000
+#define PI_ERR_ST0_VALID_SHFT	63
+
+/* Fields in PI_ERR_STATUS1_[AB] */
+#define PI_ERR_ST1_SPOOL_MASK	0x00000000001fffff
+#define PI_ERR_ST1_SPOOL_SHFT	0
+#define PI_ERR_ST1_TOUTCNT_MASK 0x000000001fe00000
+#define PI_ERR_ST1_TOUTCNT_SHFT 21
+#define PI_ERR_ST1_INVCNT_MASK	0x0000007fe0000000
+#define PI_ERR_ST1_INVCNT_SHFT	29
+#define PI_ERR_ST1_CRBNUM_MASK	0x0000038000000000
+#define PI_ERR_ST1_CRBNUM_SHFT	39
+#define PI_ERR_ST1_WRBRRB_MASK	0x0000040000000000
+#define PI_ERR_ST1_WRBRRB_SHFT	42
+#define PI_ERR_ST1_CRBSTAT_MASK 0x001ff80000000000
+#define PI_ERR_ST1_CRBSTAT_SHFT 43
+#define PI_ERR_ST1_MSGSRC_MASK	0xffe0000000000000
+#define PI_ERR_ST1_MSGSRC_SHFT	53
+
+/* Fields in the error stack */
+#define PI_ERR_STK_TYPE_MASK	0x0000000000000003
+#define PI_ERR_STK_TYPE_SHFT	0
+#define PI_ERR_STK_SUPPL_MASK	0x0000000000000038
+#define PI_ERR_STK_SUPPL_SHFT	3
+#define PI_ERR_STK_REQNUM_MASK	0x00000000000001c0
+#define PI_ERR_STK_REQNUM_SHFT	6
+#define PI_ERR_STK_CRBNUM_MASK	0x0000000000000e00
+#define PI_ERR_STK_CRBNUM_SHFT	9
+#define PI_ERR_STK_WRBRRB_MASK	0x0000000000001000
+#define PI_ERR_STK_WRBRRB_SHFT	12
+#define PI_ERR_STK_CRBSTAT_MASK 0x00000000007fe000
+#define PI_ERR_STK_CRBSTAT_SHFT 13
+#define PI_ERR_STK_CMD_MASK	0x000000007f800000
+#define PI_ERR_STK_CMD_SHFT	23
+#define PI_ERR_STK_ADDR_MASK	0xffffffff80000000
+#define PI_ERR_STK_ADDR_SHFT	31
+
+/* Error type in the error status or stack on Read CRBs */
+#define PI_ERR_RD_PRERR		1
+#define PI_ERR_RD_DERR		2
+#define PI_ERR_RD_TERR		3
+
+/* Error type in the error status or stack on Write CRBs */
+#define PI_ERR_WR_WERR		0
+#define PI_ERR_WR_PWERR		1
+#define PI_ERR_WR_TERR		3
+
+/* Read or Write CRB in error status or stack */
+#define PI_ERR_RRB	0
+#define PI_ERR_WRB	1
+#define PI_ERR_ANY_CRB	2
+
+/* Address masks in the error status and error stack are not the same */
+#define ERR_STK_ADDR_SHFT	7
+#define ERR_STAT0_ADDR_SHFT	3
+
+#define PI_MIN_STACK_SIZE 4096	/* For figuring out the size to set */
+#define PI_STACK_SIZE_SHFT	12	/* 4k */
+
+#define ERR_STACK_SIZE_BYTES(_sz) \
+       ((_sz) ? (PI_MIN_STACK_SIZE << ((_sz) - 1)) : 0)
+
+#ifndef __ASSEMBLY__
+/*
+ * format of error stack and error status registers.
+ */
+
+struct err_stack_format {
+	u64	sk_addr	   : 33,   /* address */
+		sk_cmd	   :  8,   /* message command */
+		sk_crb_sts : 10,   /* status from RRB or WRB */
+		sk_rw_rb   :  1,   /* RRB == 0, WRB == 1 */
+		sk_crb_num :  3,   /* WRB (0 to 7) or RRB (0 to 4) */
+		sk_t5_req  :  3,   /* RRB T5 request number */
+		sk_suppl   :  3,   /* lowest 3 bit of supplemental */
+		sk_err_type:  3;   /* error type	*/
+};
+
+typedef union pi_err_stack {
+	u64	pi_stk_word;
+	struct	err_stack_format pi_stk_fmt;
+} pi_err_stack_t;
+
+struct err_status0_format {
+	u64	s0_valid   :  1,   /* Valid */
+		s0_ovr_run :  1,   /* Overrun, spooled to memory */
+		s0_addr	   : 37,   /* address */
+		s0_cmd	   :  8,   /* message command */
+		s0_supl	   : 11,   /* message supplemental field */
+		s0_t5_req  :  3,   /* RRB T5 request number */
+		s0_err_type:  3;   /* error type */
+};
+
+typedef union pi_err_stat0 {
+	u64	pi_stat0_word;
+	struct err_status0_format pi_stat0_fmt;
+} pi_err_stat0_t;
+
+struct err_status1_format {
+	u64	s1_src	   : 11,   /* message source */
+		s1_crb_sts : 10,   /* status from RRB or WRB */
+		s1_rw_rb   :  1,   /* RRB == 0, WRB == 1 */
+		s1_crb_num :  3,   /* WRB (0 to 7) or RRB (0 to 4) */
+		s1_inval_cnt:10,   /* signed invalidate counter RRB */
+		s1_to_cnt  :  8,   /* crb timeout counter */
+		s1_spl_cnt : 21;   /* number spooled to memory */
+};
+
+typedef union pi_err_stat1 {
+	u64	pi_stat1_word;
+	struct err_status1_format pi_stat1_fmt;
+} pi_err_stat1_t;
+
+typedef u64	rtc_time_t;
+
+#endif /* !__ASSEMBLY__ */
+
+
+/* Bits in PI_SYSAD_ERRCHK_EN */
+#define PI_SYSAD_ERRCHK_ECCGEN	0x01	/* Enable ECC generation	    */
+#define PI_SYSAD_ERRCHK_QUALGEN 0x02	/* Enable data quality signal gen.  */
+#define PI_SYSAD_ERRCHK_SADP	0x04	/* Enable SysAD parity checking	    */
+#define PI_SYSAD_ERRCHK_CMDP	0x08	/* Enable SysCmd parity checking    */
+#define PI_SYSAD_ERRCHK_STATE	0x10	/* Enable SysState parity checking  */
+#define PI_SYSAD_ERRCHK_QUAL	0x20	/* Enable data quality checking	    */
+#define PI_SYSAD_CHECK_ALL	0x3f	/* Generate and check all signals.  */
+
+/* Interrupt pending bits on R10000 */
+
+#define HUB_IP_PEND0		0x0400
+#define HUB_IP_PEND1_CC		0x0800
+#define HUB_IP_RT		0x1000
+#define HUB_IP_PROF		0x2000
+#define HUB_IP_ERROR		0x4000
+#define HUB_IP_MASK		0x7c00
+
+/* PI_RT_LOCAL_CTRL mask and shift definitions */
+
+#define PRLC_USE_INT_SHFT	16
+#define PRLC_USE_INT_MASK	(UINT64_CAST 1 << 16)
+#define PRLC_USE_INT		(UINT64_CAST 1 << 16)
+#define PRLC_GCLK_SHFT		15
+#define PRLC_GCLK_MASK		(UINT64_CAST 1 << 15)
+#define PRLC_GCLK		(UINT64_CAST 1 << 15)
+#define PRLC_GCLK_COUNT_SHFT	8
+#define PRLC_GCLK_COUNT_MASK	(UINT64_CAST 0x7f << 8)
+#define PRLC_MAX_COUNT_SHFT	1
+#define PRLC_MAX_COUNT_MASK	(UINT64_CAST 0x7f << 1)
+#define PRLC_GCLK_EN_SHFT	0
+#define PRLC_GCLK_EN_MASK	(UINT64_CAST 1)
+#define PRLC_GCLK_EN		(UINT64_CAST 1)
+
+/* PI_RT_FILTER_CTRL mask and shift definitions */
+
+/*
+ * Bits for NACK_CNT_A/B and NACK_CMP
+ */
+#define PI_NACK_CNT_EN_SHFT	20
+#define PI_NACK_CNT_EN_MASK	0x100000
+#define PI_NACK_CNT_MASK	0x0fffff
+#define PI_NACK_CNT_MAX		0x0fffff
+
+#endif /* _ASM_SN_SN0_HUBPI_H */
diff --git a/arch/mips/include/asm/sn/sn0/kldir.h b/arch/mips/include/asm/sn/sn0/kldir.h
new file mode 100644
index 000000000..1b10af6cb
--- /dev/null
+++ b/arch/mips/include/asm/sn/sn0/kldir.h
@@ -0,0 +1,186 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Derived from IRIX <sys/SN/kldir.h>, revision 1.21.
+ *
+ * Copyright (C) 1992 - 1997, 1999, 2000 Silicon Graphics, Inc.
+ * Copyright (C) 1999, 2000 by Ralf Baechle
+ */
+#ifndef _ASM_SN_SN0_KLDIR_H
+#define _ASM_SN_SN0_KLDIR_H
+
+
+/*
+ * The kldir memory area resides at a fixed place in each node's memory and
+ * provides pointers to most other IP27 memory areas.  This allows us to
+ * resize and/or relocate memory areas at a later time without breaking all
+ * firmware and kernels that use them.	Indices in the array are
+ * permanently dedicated to areas listed below.	 Some memory areas (marked
+ * below) reside at a permanently fixed location, but are included in the
+ * directory for completeness.
+ */
+
+/*
+ * The upper portion of the memory map applies during boot
+ * only and is overwritten by IRIX/SYMMON.
+ *
+ *				      MEMORY MAP PER NODE
+ *
+ * 0x2000000 (32M)	   +-----------------------------------------+
+ *			   |	  IO6 BUFFERS FOR FLASH ENET IOC3    |
+ * 0x1F80000 (31.5M)	   +-----------------------------------------+
+ *			   |	  IO6 TEXT/DATA/BSS/stack	     |
+ * 0x1C00000 (30M)	   +-----------------------------------------+
+ *			   |	  IO6 PROM DEBUG TEXT/DATA/BSS/stack |
+ * 0x0800000 (28M)	   +-----------------------------------------+
+ *			   |	  IP27 PROM TEXT/DATA/BSS/stack	     |
+ * 0x1B00000 (27M)	   +-----------------------------------------+
+ *			   |	  IP27 CFG			     |
+ * 0x1A00000 (26M)	   +-----------------------------------------+
+ *			   |	  Graphics PROM			     |
+ * 0x1800000 (24M)	   +-----------------------------------------+
+ *			   |	  3rd Party PROM drivers	     |
+ * 0x1600000 (22M)	   +-----------------------------------------+
+ *			   |					     |
+ *			   |	  Free				     |
+ *			   |					     |
+ *			   +-----------------------------------------+
+ *			   |	  UNIX DEBUG Version		     |
+ * 0x190000 (2M--)	   +-----------------------------------------+
+ *			   |	  SYMMON			     |
+ *			   |	  (For UNIX Debug only)		     |
+ * 0x34000 (208K)	   +-----------------------------------------+
+ *			   |	  SYMMON STACK [NUM_CPU_PER_NODE]    |
+ *			   |	  (For UNIX Debug only)		     |
+ * 0x25000 (148K)	   +-----------------------------------------+
+ *			   |	  KLCONFIG - II (temp)		     |
+ *			   |					     |
+ *			   |	----------------------------	     |
+ *			   |					     |
+ *			   |	  UNIX NON-DEBUG Version	     |
+ * 0x19000 (100K)	   +-----------------------------------------+
+ *
+ *
+ * The lower portion of the memory map contains information that is
+ * permanent and is used by the IP27PROM, IO6PROM and IRIX.
+ *
+ * 0x19000 (100K)	   +-----------------------------------------+
+ *			   |					     |
+ *			   |	  PI Error Spools (32K)		     |
+ *			   |					     |
+ * 0x12000 (72K)	   +-----------------------------------------+
+ *			   |	  Unused			     |
+ * 0x11c00 (71K)	   +-----------------------------------------+
+ *			   |	  CPU 1 NMI Eframe area		     |
+ * 0x11a00 (70.5K)	   +-----------------------------------------+
+ *			   |	  CPU 0 NMI Eframe area		     |
+ * 0x11800 (70K)	   +-----------------------------------------+
+ *			   |	  CPU 1 NMI Register save area	     |
+ * 0x11600 (69.5K)	   +-----------------------------------------+
+ *			   |	  CPU 0 NMI Register save area	     |
+ * 0x11400 (69K)	   +-----------------------------------------+
+ *			   |	  GDA (1k)			     |
+ * 0x11000 (68K)	   +-----------------------------------------+
+ *			   |	  Early cache Exception stack	     |
+ *			   |		 and/or			     |
+ *			   |	  kernel/io6prom nmi registers	     |
+ * 0x10800  (66k)	   +-----------------------------------------+
+ *			   |	  cache error eframe		     |
+ * 0x10400 (65K)	   +-----------------------------------------+
+ *			   |	  Exception Handlers (UALIAS copy)   |
+ * 0x10000 (64K)	   +-----------------------------------------+
+ *			   |					     |
+ *			   |					     |
+ *			   |	  KLCONFIG - I (permanent) (48K)     |
+ *			   |					     |
+ *			   |					     |
+ *			   |					     |
+ * 0x4000 (16K)		   +-----------------------------------------+
+ *			   |	  NMI Handler (Protected Page)	     |
+ * 0x3000 (12K)		   +-----------------------------------------+
+ *			   |	  ARCS PVECTORS (master node only)   |
+ * 0x2c00 (11K)		   +-----------------------------------------+
+ *			   |	  ARCS TVECTORS (master node only)   |
+ * 0x2800 (10K)		   +-----------------------------------------+
+ *			   |	  LAUNCH [NUM_CPU]		     |
+ * 0x2400 (9K)		   +-----------------------------------------+
+ *			   |	  Low memory directory (KLDIR)	     |
+ * 0x2000 (8K)		   +-----------------------------------------+
+ *			   |	  ARCS SPB (1K)			     |
+ * 0x1000 (4K)		   +-----------------------------------------+
+ *			   |	  Early cache Exception stack	     |
+ *			   |		 and/or			     |
+ *			   |	  kernel/io6prom nmi registers	     |
+ * 0x800  (2k)		   +-----------------------------------------+
+ *			   |	  cache error eframe		     |
+ * 0x400 (1K)		   +-----------------------------------------+
+ *			   |	  Exception Handlers		     |
+ * 0x0	 (0K)		   +-----------------------------------------+
+ */
+
+/*
+ * This is defined here because IP27_SYMMON_STK_SIZE must be at least what
+ * we define here.  Since it's set up in the prom.  We can't redefine it later
+ * and expect more space to be allocated.  The way to find out the true size
+ * of the symmon stacks is to divide SYMMON_STK_SIZE by SYMMON_STK_STRIDE
+ * for a particular node.
+ */
+#define SYMMON_STACK_SIZE		0x8000
+
+#if defined(PROM)
+
+/*
+ * These defines are prom version dependent.  No code other than the IP27
+ * prom should attempt to use these values.
+ */
+#define IP27_LAUNCH_OFFSET		0x2400
+#define IP27_LAUNCH_SIZE		0x400
+#define IP27_LAUNCH_COUNT		2
+#define IP27_LAUNCH_STRIDE		0x200
+
+#define IP27_KLCONFIG_OFFSET		0x4000
+#define IP27_KLCONFIG_SIZE		0xc000
+#define IP27_KLCONFIG_COUNT		1
+#define IP27_KLCONFIG_STRIDE		0
+
+#define IP27_NMI_OFFSET			0x3000
+#define IP27_NMI_SIZE			0x40
+#define IP27_NMI_COUNT			2
+#define IP27_NMI_STRIDE			0x40
+
+#define IP27_PI_ERROR_OFFSET		0x12000
+#define IP27_PI_ERROR_SIZE		0x4000
+#define IP27_PI_ERROR_COUNT		1
+#define IP27_PI_ERROR_STRIDE		0
+
+#define IP27_SYMMON_STK_OFFSET		0x25000
+#define IP27_SYMMON_STK_SIZE		0xe000
+#define IP27_SYMMON_STK_COUNT		2
+/* IP27_SYMMON_STK_STRIDE must be >= SYMMON_STACK_SIZE */
+#define IP27_SYMMON_STK_STRIDE		0x7000
+
+#define IP27_FREEMEM_OFFSET		0x19000
+#define IP27_FREEMEM_SIZE		-1
+#define IP27_FREEMEM_COUNT		1
+#define IP27_FREEMEM_STRIDE		0
+
+#endif /* PROM */
+/*
+ * There will be only one of these in a partition so the IO6 must set it up.
+ */
+#define IO6_GDA_OFFSET			0x11000
+#define IO6_GDA_SIZE			0x400
+#define IO6_GDA_COUNT			1
+#define IO6_GDA_STRIDE			0
+
+/*
+ * save area of kernel nmi regs in the prom format
+ */
+#define IP27_NMI_KREGS_OFFSET		0x11400
+#define IP27_NMI_KREGS_CPU_SIZE		0x200
+/*
+ * save area of kernel nmi regs in eframe format
+ */
+#define IP27_NMI_EFRAME_OFFSET		0x11800
+#define IP27_NMI_EFRAME_SIZE		0x200
+
+#endif /* _ASM_SN_SN0_KLDIR_H */
diff --git a/arch/mips/include/asm/sn/types.h b/arch/mips/include/asm/sn/types.h
new file mode 100644
index 000000000..451ba1ee4
--- /dev/null
+++ b/arch/mips/include/asm/sn/types.h
@@ -0,0 +1,25 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ * Copyright (C) 1999 by Ralf Baechle
+ */
+#ifndef _ASM_SN_TYPES_H
+#define _ASM_SN_TYPES_H
+
+#include <linux/types.h>
+
+#ifndef __ASSEMBLY__
+
+typedef unsigned long	cpuid_t;
+typedef signed short	nasid_t;	/* node id in numa-as-id space */
+typedef signed char	partid_t;	/* partition ID type */
+typedef signed short	moduleid_t;	/* user-visible module number type */
+
+typedef dev_t		vertex_hdl_t;	/* hardware graph vertex handle */
+
+#endif
+
+#endif /* _ASM_SN_TYPES_H */
diff --git a/arch/mips/include/asm/sni.h b/arch/mips/include/asm/sni.h
new file mode 100644
index 000000000..7fb6656a6
--- /dev/null
+++ b/arch/mips/include/asm/sni.h
@@ -0,0 +1,243 @@
+/*
+ * SNI specific definitions
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1997, 1998 by Ralf Baechle
+ * Copyright (C) 2006 Thomas Bogendoerfer (tsbogend@alpha.franken.de)
+ */
+#ifndef __ASM_SNI_H
+#define __ASM_SNI_H
+
+#include <linux/irqreturn.h>
+
+extern unsigned int sni_brd_type;
+
+#define SNI_BRD_10		   2
+#define SNI_BRD_10NEW		   3
+#define SNI_BRD_TOWER_OASIC	   4
+#define SNI_BRD_MINITOWER	   5
+#define SNI_BRD_PCI_TOWER	   6
+#define SNI_BRD_RM200		   7
+#define SNI_BRD_PCI_MTOWER	   8
+#define SNI_BRD_PCI_DESKTOP	   9
+#define SNI_BRD_PCI_TOWER_CPLUS	  10
+#define SNI_BRD_PCI_MTOWER_CPLUS  11
+
+/* RM400 cpu types */
+#define SNI_CPU_M8021		0x01
+#define SNI_CPU_M8030		0x04
+#define SNI_CPU_M8031		0x06
+#define SNI_CPU_M8034		0x0f
+#define SNI_CPU_M8037		0x07
+#define SNI_CPU_M8040		0x05
+#define SNI_CPU_M8043		0x09
+#define SNI_CPU_M8050		0x0b
+#define SNI_CPU_M8053		0x0d
+
+#define SNI_PORT_BASE		CKSEG1ADDR(0xb4000000)
+
+#ifndef __MIPSEL__
+/*
+ * ASIC PCI registers for big endian configuration.
+ */
+#define PCIMT_UCONF		CKSEG1ADDR(0xbfff0004)
+#define PCIMT_IOADTIMEOUT2	CKSEG1ADDR(0xbfff000c)
+#define PCIMT_IOMEMCONF		CKSEG1ADDR(0xbfff0014)
+#define PCIMT_IOMMU		CKSEG1ADDR(0xbfff001c)
+#define PCIMT_IOADTIMEOUT1	CKSEG1ADDR(0xbfff0024)
+#define PCIMT_DMAACCESS		CKSEG1ADDR(0xbfff002c)
+#define PCIMT_DMAHIT		CKSEG1ADDR(0xbfff0034)
+#define PCIMT_ERRSTATUS		CKSEG1ADDR(0xbfff003c)
+#define PCIMT_ERRADDR		CKSEG1ADDR(0xbfff0044)
+#define PCIMT_SYNDROME		CKSEG1ADDR(0xbfff004c)
+#define PCIMT_ITPEND		CKSEG1ADDR(0xbfff0054)
+#define	 IT_INT2		0x01
+#define	 IT_INTD		0x02
+#define	 IT_INTC		0x04
+#define	 IT_INTB		0x08
+#define	 IT_INTA		0x10
+#define	 IT_EISA		0x20
+#define	 IT_SCSI		0x40
+#define	 IT_ETH			0x80
+#define PCIMT_IRQSEL		CKSEG1ADDR(0xbfff005c)
+#define PCIMT_TESTMEM		CKSEG1ADDR(0xbfff0064)
+#define PCIMT_ECCREG		CKSEG1ADDR(0xbfff006c)
+#define PCIMT_CONFIG_ADDRESS	CKSEG1ADDR(0xbfff0074)
+#define PCIMT_ASIC_ID		CKSEG1ADDR(0xbfff007c)	/* read */
+#define PCIMT_SOFT_RESET	CKSEG1ADDR(0xbfff007c)	/* write */
+#define PCIMT_PIA_OE		CKSEG1ADDR(0xbfff0084)
+#define PCIMT_PIA_DATAOUT	CKSEG1ADDR(0xbfff008c)
+#define PCIMT_PIA_DATAIN	CKSEG1ADDR(0xbfff0094)
+#define PCIMT_CACHECONF		CKSEG1ADDR(0xbfff009c)
+#define PCIMT_INVSPACE		CKSEG1ADDR(0xbfff00a4)
+#else
+/*
+ * ASIC PCI registers for little endian configuration.
+ */
+#define PCIMT_UCONF		CKSEG1ADDR(0xbfff0000)
+#define PCIMT_IOADTIMEOUT2	CKSEG1ADDR(0xbfff0008)
+#define PCIMT_IOMEMCONF		CKSEG1ADDR(0xbfff0010)
+#define PCIMT_IOMMU		CKSEG1ADDR(0xbfff0018)
+#define PCIMT_IOADTIMEOUT1	CKSEG1ADDR(0xbfff0020)
+#define PCIMT_DMAACCESS		CKSEG1ADDR(0xbfff0028)
+#define PCIMT_DMAHIT		CKSEG1ADDR(0xbfff0030)
+#define PCIMT_ERRSTATUS		CKSEG1ADDR(0xbfff0038)
+#define PCIMT_ERRADDR		CKSEG1ADDR(0xbfff0040)
+#define PCIMT_SYNDROME		CKSEG1ADDR(0xbfff0048)
+#define PCIMT_ITPEND		CKSEG1ADDR(0xbfff0050)
+#define	 IT_INT2		0x01
+#define	 IT_INTD		0x02
+#define	 IT_INTC		0x04
+#define	 IT_INTB		0x08
+#define	 IT_INTA		0x10
+#define	 IT_EISA		0x20
+#define	 IT_SCSI		0x40
+#define	 IT_ETH			0x80
+#define PCIMT_IRQSEL		CKSEG1ADDR(0xbfff0058)
+#define PCIMT_TESTMEM		CKSEG1ADDR(0xbfff0060)
+#define PCIMT_ECCREG		CKSEG1ADDR(0xbfff0068)
+#define PCIMT_CONFIG_ADDRESS	CKSEG1ADDR(0xbfff0070)
+#define PCIMT_ASIC_ID		CKSEG1ADDR(0xbfff0078)	/* read */
+#define PCIMT_SOFT_RESET	CKSEG1ADDR(0xbfff0078)	/* write */
+#define PCIMT_PIA_OE		CKSEG1ADDR(0xbfff0080)
+#define PCIMT_PIA_DATAOUT	CKSEG1ADDR(0xbfff0088)
+#define PCIMT_PIA_DATAIN	CKSEG1ADDR(0xbfff0090)
+#define PCIMT_CACHECONF		CKSEG1ADDR(0xbfff0098)
+#define PCIMT_INVSPACE		CKSEG1ADDR(0xbfff00a0)
+#endif
+
+#define PCIMT_PCI_CONF		CKSEG1ADDR(0xbfff0100)
+
+/*
+ * Data port for the PCI bus in IO space
+ */
+#define PCIMT_CONFIG_DATA	0x0cfc
+
+/*
+ * Board specific registers
+ */
+#define PCIMT_CSMSR		CKSEG1ADDR(0xbfd00000)
+#define PCIMT_CSSWITCH		CKSEG1ADDR(0xbfd10000)
+#define PCIMT_CSITPEND		CKSEG1ADDR(0xbfd20000)
+#define PCIMT_AUTO_PO_EN	CKSEG1ADDR(0xbfd30000)
+#define PCIMT_CLR_TEMP		CKSEG1ADDR(0xbfd40000)
+#define PCIMT_AUTO_PO_DIS	CKSEG1ADDR(0xbfd50000)
+#define PCIMT_EXMSR		CKSEG1ADDR(0xbfd60000)
+#define PCIMT_UNUSED1		CKSEG1ADDR(0xbfd70000)
+#define PCIMT_CSWCSM		CKSEG1ADDR(0xbfd80000)
+#define PCIMT_UNUSED2		CKSEG1ADDR(0xbfd90000)
+#define PCIMT_CSLED		CKSEG1ADDR(0xbfda0000)
+#define PCIMT_CSMAPISA		CKSEG1ADDR(0xbfdb0000)
+#define PCIMT_CSRSTBP		CKSEG1ADDR(0xbfdc0000)
+#define PCIMT_CLRPOFF		CKSEG1ADDR(0xbfdd0000)
+#define PCIMT_CSTIMER		CKSEG1ADDR(0xbfde0000)
+#define PCIMT_PWDN		CKSEG1ADDR(0xbfdf0000)
+
+/*
+ * A20R based boards
+ */
+#define A20R_PT_CLOCK_BASE	CKSEG1ADDR(0xbc040000)
+#define A20R_PT_TIM0_ACK	CKSEG1ADDR(0xbc050000)
+#define A20R_PT_TIM1_ACK	CKSEG1ADDR(0xbc060000)
+
+#define SNI_A20R_IRQ_BASE	MIPS_CPU_IRQ_BASE
+#define SNI_A20R_IRQ_TIMER	(SNI_A20R_IRQ_BASE+5)
+
+#define SNI_PCIT_INT_REG	CKSEG1ADDR(0xbfff000c)
+
+#define SNI_PCIT_INT_START	24
+#define SNI_PCIT_INT_END	30
+
+#define PCIT_IRQ_ETHERNET	(MIPS_CPU_IRQ_BASE + 5)
+#define PCIT_IRQ_INTA		(SNI_PCIT_INT_START + 0)
+#define PCIT_IRQ_INTB		(SNI_PCIT_INT_START + 1)
+#define PCIT_IRQ_INTC		(SNI_PCIT_INT_START + 2)
+#define PCIT_IRQ_INTD		(SNI_PCIT_INT_START + 3)
+#define PCIT_IRQ_SCSI0		(SNI_PCIT_INT_START + 4)
+#define PCIT_IRQ_SCSI1		(SNI_PCIT_INT_START + 5)
+
+
+/*
+ * Interrupt 0-16 are EISA interrupts.	Interrupts from 16 on are assigned
+ * to the other interrupts generated by ASIC PCI.
+ *
+ * INT2 is a wired-or of the push button interrupt, high temperature interrupt
+ * ASIC PCI interrupt.
+ */
+#define PCIMT_KEYBOARD_IRQ	 1
+#define PCIMT_IRQ_INT2		24
+#define PCIMT_IRQ_INTD		25
+#define PCIMT_IRQ_INTC		26
+#define PCIMT_IRQ_INTB		27
+#define PCIMT_IRQ_INTA		28
+#define PCIMT_IRQ_EISA		29
+#define PCIMT_IRQ_SCSI		30
+
+#define PCIMT_IRQ_ETHERNET	(MIPS_CPU_IRQ_BASE+6)
+
+#if 0
+#define PCIMT_IRQ_TEMPERATURE	24
+#define PCIMT_IRQ_EISA_NMI	25
+#define PCIMT_IRQ_POWER_OFF	26
+#define PCIMT_IRQ_BUTTON	27
+#endif
+
+/*
+ * Base address for the mapped 16mb EISA bus segment.
+ */
+#define PCIMT_EISA_BASE		CKSEG1ADDR(0xb0000000)
+
+/* PCI EISA Interrupt acknowledge  */
+#define PCIMT_INT_ACKNOWLEDGE	CKSEG1ADDR(0xba000000)
+
+/*
+ *  SNI ID PROM
+ *
+ * SNI_IDPROM_MEMSIZE  Memsize in 16MB quantities
+ * SNI_IDPROM_BRDTYPE  Board Type
+ * SNI_IDPROM_CPUTYPE  CPU Type on RM400
+ */
+#ifdef CONFIG_CPU_BIG_ENDIAN
+#define __SNI_END 0
+#endif
+#ifdef CONFIG_CPU_LITTLE_ENDIAN
+#define __SNI_END 3
+#endif
+#define SNI_IDPROM_BASE	       CKSEG1ADDR(0x1ff00000)
+#define SNI_IDPROM_MEMSIZE     (SNI_IDPROM_BASE + (0x28 ^ __SNI_END))
+#define SNI_IDPROM_BRDTYPE     (SNI_IDPROM_BASE + (0x29 ^ __SNI_END))
+#define SNI_IDPROM_CPUTYPE     (SNI_IDPROM_BASE + (0x30 ^ __SNI_END))
+
+#define SNI_IDPROM_SIZE 0x1000
+
+/* board specific init functions */
+extern void sni_a20r_init(void);
+extern void sni_pcit_init(void);
+extern void sni_rm200_init(void);
+extern void sni_pcimt_init(void);
+
+/* board specific irq init functions */
+extern void sni_a20r_irq_init(void);
+extern void sni_pcit_irq_init(void);
+extern void sni_pcit_cplus_irq_init(void);
+extern void sni_rm200_irq_init(void);
+extern void sni_pcimt_irq_init(void);
+
+/* eisa init for RM200/400 */
+#ifdef CONFIG_EISA
+extern int sni_eisa_root_init(void);
+#else
+static inline int sni_eisa_root_init(void)
+{
+	return 0;
+}
+#endif
+
+/* common irq stuff */
+extern void (*sni_hwint)(void);
+extern irqreturn_t sni_isa_irq_handler(int dummy, void *p);
+
+#endif /* __ASM_SNI_H */
diff --git a/arch/mips/include/asm/socket.h b/arch/mips/include/asm/socket.h
new file mode 100644
index 000000000..4724a563c
--- /dev/null
+++ b/arch/mips/include/asm/socket.h
@@ -0,0 +1,50 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1997, 1999, 2000, 2001 Ralf Baechle
+ * Copyright (C) 2000, 2001 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_SOCKET_H
+#define _ASM_SOCKET_H
+
+#include <uapi/asm/socket.h>
+
+
+/** sock_type - Socket types
+ *
+ * Please notice that for binary compat reasons MIPS has to
+ * override the enum sock_type in include/linux/net.h, so
+ * we define ARCH_HAS_SOCKET_TYPES here.
+ *
+ * @SOCK_DGRAM - datagram (conn.less) socket
+ * @SOCK_STREAM - stream (connection) socket
+ * @SOCK_RAW - raw socket
+ * @SOCK_RDM - reliably-delivered message
+ * @SOCK_SEQPACKET - sequential packet socket
+ * @SOCK_PACKET - linux specific way of getting packets at the dev level.
+ *		  For writing rarp and other similar things on the user level.
+ */
+enum sock_type {
+	SOCK_DGRAM	= 1,
+	SOCK_STREAM	= 2,
+	SOCK_RAW	= 3,
+	SOCK_RDM	= 4,
+	SOCK_SEQPACKET	= 5,
+	SOCK_DCCP	= 6,
+	SOCK_PACKET	= 10,
+};
+
+#define SOCK_MAX (SOCK_PACKET + 1)
+/* Mask which covers at least up to SOCK_MASK-1.  The
+ *  * remaining bits are used as flags. */
+#define SOCK_TYPE_MASK 0xf
+
+/* Flags for socket, socketpair, paccept */
+#define SOCK_CLOEXEC	O_CLOEXEC
+#define SOCK_NONBLOCK	O_NONBLOCK
+
+#define ARCH_HAS_SOCKET_TYPES 1
+
+#endif /* _ASM_SOCKET_H */
diff --git a/arch/mips/include/asm/sparsemem.h b/arch/mips/include/asm/sparsemem.h
new file mode 100644
index 000000000..b0686ca3d
--- /dev/null
+++ b/arch/mips/include/asm/sparsemem.h
@@ -0,0 +1,18 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _MIPS_SPARSEMEM_H
+#define _MIPS_SPARSEMEM_H
+#ifdef CONFIG_SPARSEMEM
+
+/*
+ * SECTION_SIZE_BITS		2^N: how big each section will be
+ * MAX_PHYSMEM_BITS		2^N: how much memory we can have in that space
+ */
+#if defined(CONFIG_MIPS_HUGE_TLB_SUPPORT) && defined(CONFIG_PAGE_SIZE_64KB)
+# define SECTION_SIZE_BITS	29
+#else
+# define SECTION_SIZE_BITS	28
+#endif
+#define MAX_PHYSMEM_BITS	48
+
+#endif /* CONFIG_SPARSEMEM */
+#endif /* _MIPS_SPARSEMEM_H */
diff --git a/arch/mips/include/asm/spinlock.h b/arch/mips/include/asm/spinlock.h
new file mode 100644
index 000000000..6ce2117e4
--- /dev/null
+++ b/arch/mips/include/asm/spinlock.h
@@ -0,0 +1,31 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1999, 2000, 06 Ralf Baechle (ralf@linux-mips.org)
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_SPINLOCK_H
+#define _ASM_SPINLOCK_H
+
+#include <asm/processor.h>
+
+#include <asm-generic/qspinlock_types.h>
+
+#define	queued_spin_unlock queued_spin_unlock
+/**
+ * queued_spin_unlock - release a queued spinlock
+ * @lock : Pointer to queued spinlock structure
+ */
+static inline void queued_spin_unlock(struct qspinlock *lock)
+{
+	/* This could be optimised with ARCH_HAS_MMIOWB */
+	mmiowb();
+	smp_store_release(&lock->locked, 0);
+}
+
+#include <asm/qspinlock.h>
+#include <asm/qrwlock.h>
+
+#endif /* _ASM_SPINLOCK_H */
diff --git a/arch/mips/include/asm/spinlock_types.h b/arch/mips/include/asm/spinlock_types.h
new file mode 100644
index 000000000..28fd4b140
--- /dev/null
+++ b/arch/mips/include/asm/spinlock_types.h
@@ -0,0 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _ASM_SPINLOCK_TYPES_H
+#define _ASM_SPINLOCK_TYPES_H
+
+#include <asm-generic/qspinlock_types.h>
+#include <asm-generic/qrwlock_types.h>
+
+#endif
diff --git a/arch/mips/include/asm/spram.h b/arch/mips/include/asm/spram.h
new file mode 100644
index 000000000..373f2a5d4
--- /dev/null
+++ b/arch/mips/include/asm/spram.h
@@ -0,0 +1,11 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _MIPS_SPRAM_H
+#define _MIPS_SPRAM_H
+
+#if defined(CONFIG_MIPS_SPRAM)
+extern __init void spram_config(void);
+#else
+static inline void spram_config(void) { }
+#endif /* CONFIG_MIPS_SPRAM */
+
+#endif /* _MIPS_SPRAM_H */
diff --git a/arch/mips/include/asm/stackframe.h b/arch/mips/include/asm/stackframe.h
new file mode 100644
index 000000000..a8705aef4
--- /dev/null
+++ b/arch/mips/include/asm/stackframe.h
@@ -0,0 +1,492 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994, 95, 96, 99, 2001 Ralf Baechle
+ * Copyright (C) 1994, 1995, 1996 Paul M. Antoine.
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ * Copyright (C) 2007  Maciej W. Rozycki
+ */
+#ifndef _ASM_STACKFRAME_H
+#define _ASM_STACKFRAME_H
+
+#include <linux/threads.h>
+
+#include <asm/asm.h>
+#include <asm/asmmacro.h>
+#include <asm/mipsregs.h>
+#include <asm/asm-offsets.h>
+#include <asm/thread_info.h>
+
+/* Make the addition of cfi info a little easier. */
+	.macro cfi_rel_offset reg offset=0 docfi=0
+	.if \docfi
+	.cfi_rel_offset \reg, \offset
+	.endif
+	.endm
+
+	.macro cfi_st reg offset=0 docfi=0
+	LONG_S	\reg, \offset(sp)
+	cfi_rel_offset \reg, \offset, \docfi
+	.endm
+
+	.macro cfi_restore reg offset=0 docfi=0
+	.if \docfi
+	.cfi_restore \reg
+	.endif
+	.endm
+
+	.macro cfi_ld reg offset=0 docfi=0
+	LONG_L	\reg, \offset(sp)
+	cfi_restore \reg \offset \docfi
+	.endm
+
+#if defined(CONFIG_CPU_R3000)
+#define STATMASK 0x3f
+#else
+#define STATMASK 0x1f
+#endif
+
+		.macro	SAVE_AT docfi=0
+		.set	push
+		.set	noat
+		cfi_st	$1, PT_R1, \docfi
+		.set	pop
+		.endm
+
+		.macro	SAVE_TEMP docfi=0
+#ifdef CONFIG_CPU_HAS_SMARTMIPS
+		mflhxu	v1
+		LONG_S	v1, PT_LO(sp)
+		mflhxu	v1
+		LONG_S	v1, PT_HI(sp)
+		mflhxu	v1
+		LONG_S	v1, PT_ACX(sp)
+#elif !defined(CONFIG_CPU_MIPSR6)
+		mfhi	v1
+#endif
+#ifdef CONFIG_32BIT
+		cfi_st	$8, PT_R8, \docfi
+		cfi_st	$9, PT_R9, \docfi
+#endif
+		cfi_st	$10, PT_R10, \docfi
+		cfi_st	$11, PT_R11, \docfi
+		cfi_st	$12, PT_R12, \docfi
+#if !defined(CONFIG_CPU_HAS_SMARTMIPS) && !defined(CONFIG_CPU_MIPSR6)
+		LONG_S	v1, PT_HI(sp)
+		mflo	v1
+#endif
+		cfi_st	$13, PT_R13, \docfi
+		cfi_st	$14, PT_R14, \docfi
+		cfi_st	$15, PT_R15, \docfi
+		cfi_st	$24, PT_R24, \docfi
+#if !defined(CONFIG_CPU_HAS_SMARTMIPS) && !defined(CONFIG_CPU_MIPSR6)
+		LONG_S	v1, PT_LO(sp)
+#endif
+#ifdef CONFIG_CPU_CAVIUM_OCTEON
+		/*
+		 * The Octeon multiplier state is affected by general
+		 * multiply instructions. It must be saved before and
+		 * kernel code might corrupt it
+		 */
+		jal     octeon_mult_save
+#endif
+		.endm
+
+		.macro	SAVE_STATIC docfi=0
+		cfi_st	$16, PT_R16, \docfi
+		cfi_st	$17, PT_R17, \docfi
+		cfi_st	$18, PT_R18, \docfi
+		cfi_st	$19, PT_R19, \docfi
+		cfi_st	$20, PT_R20, \docfi
+		cfi_st	$21, PT_R21, \docfi
+		cfi_st	$22, PT_R22, \docfi
+		cfi_st	$23, PT_R23, \docfi
+		cfi_st	$30, PT_R30, \docfi
+		.endm
+
+/*
+ * get_saved_sp returns the SP for the current CPU by looking in the
+ * kernelsp array for it.  If tosp is set, it stores the current sp in
+ * k0 and loads the new value in sp.  If not, it clobbers k0 and
+ * stores the new value in k1, leaving sp unaffected.
+ */
+#ifdef CONFIG_SMP
+
+		/* SMP variation */
+		.macro	get_saved_sp docfi=0 tosp=0
+		ASM_CPUID_MFC0	k0, ASM_SMP_CPUID_REG
+#if defined(CONFIG_32BIT) || defined(KBUILD_64BIT_SYM32)
+		lui	k1, %hi(kernelsp)
+#else
+		lui	k1, %highest(kernelsp)
+		daddiu	k1, %higher(kernelsp)
+		dsll	k1, 16
+		daddiu	k1, %hi(kernelsp)
+		dsll	k1, 16
+#endif
+		LONG_SRL	k0, SMP_CPUID_PTRSHIFT
+		LONG_ADDU	k1, k0
+		.if \tosp
+		move	k0, sp
+		.if \docfi
+		.cfi_register sp, k0
+		.endif
+		LONG_L	sp, %lo(kernelsp)(k1)
+		.else
+		LONG_L	k1, %lo(kernelsp)(k1)
+		.endif
+		.endm
+
+		.macro	set_saved_sp stackp temp temp2
+		ASM_CPUID_MFC0	\temp, ASM_SMP_CPUID_REG
+		LONG_SRL	\temp, SMP_CPUID_PTRSHIFT
+		LONG_S	\stackp, kernelsp(\temp)
+		.endm
+#else /* !CONFIG_SMP */
+		/* Uniprocessor variation */
+		.macro	get_saved_sp docfi=0 tosp=0
+#ifdef CONFIG_CPU_JUMP_WORKAROUNDS
+		/*
+		 * Clear BTB (branch target buffer), forbid RAS (return address
+		 * stack) to workaround the Out-of-order Issue in Loongson2F
+		 * via its diagnostic register.
+		 */
+		move	k0, ra
+		jal	1f
+		 nop
+1:		jal	1f
+		 nop
+1:		jal	1f
+		 nop
+1:		jal	1f
+		 nop
+1:		move	ra, k0
+		li	k0, 3
+		mtc0	k0, $22
+#endif /* CONFIG_CPU_JUMP_WORKAROUNDS */
+#if defined(CONFIG_32BIT) || defined(KBUILD_64BIT_SYM32)
+		lui	k1, %hi(kernelsp)
+#else
+		lui	k1, %highest(kernelsp)
+		daddiu	k1, %higher(kernelsp)
+		dsll	k1, k1, 16
+		daddiu	k1, %hi(kernelsp)
+		dsll	k1, k1, 16
+#endif
+		.if \tosp
+		move	k0, sp
+		.if \docfi
+		.cfi_register sp, k0
+		.endif
+		LONG_L	sp, %lo(kernelsp)(k1)
+		.else
+		LONG_L	k1, %lo(kernelsp)(k1)
+		.endif
+		.endm
+
+		.macro	set_saved_sp stackp temp temp2
+		LONG_S	\stackp, kernelsp
+		.endm
+#endif
+
+		.macro	SAVE_SOME docfi=0
+		.set	push
+		.set	noat
+		.set	reorder
+		mfc0	k0, CP0_STATUS
+		sll	k0, 3		/* extract cu0 bit */
+		.set	noreorder
+		bltz	k0, 8f
+		 move	k0, sp
+		.if \docfi
+		.cfi_register sp, k0
+		.endif
+#ifdef CONFIG_EVA
+		/*
+		 * Flush interAptiv's Return Prediction Stack (RPS) by writing
+		 * EntryHi. Toggling Config7.RPS is slower and less portable.
+		 *
+		 * The RPS isn't automatically flushed when exceptions are
+		 * taken, which can result in kernel mode speculative accesses
+		 * to user addresses if the RPS mispredicts. That's harmless
+		 * when user and kernel share the same address space, but with
+		 * EVA the same user segments may be unmapped to kernel mode,
+		 * even containing sensitive MMIO regions or invalid memory.
+		 *
+		 * This can happen when the kernel sets the return address to
+		 * ret_from_* and jr's to the exception handler, which looks
+		 * more like a tail call than a function call. If nested calls
+		 * don't evict the last user address in the RPS, it will
+		 * mispredict the return and fetch from a user controlled
+		 * address into the icache.
+		 *
+		 * More recent EVA-capable cores with MAAR to restrict
+		 * speculative accesses aren't affected.
+		 */
+		MFC0	k0, CP0_ENTRYHI
+		MTC0	k0, CP0_ENTRYHI
+#endif
+		.set	reorder
+		/* Called from user mode, new stack. */
+		get_saved_sp docfi=\docfi tosp=1
+8:
+#ifdef CONFIG_CPU_DADDI_WORKAROUNDS
+		.set	at=k1
+#endif
+		PTR_SUBU sp, PT_SIZE
+#ifdef CONFIG_CPU_DADDI_WORKAROUNDS
+		.set	noat
+#endif
+		.if \docfi
+		.cfi_def_cfa sp,0
+		.endif
+		cfi_st	k0, PT_R29, \docfi
+		cfi_rel_offset  sp, PT_R29, \docfi
+		cfi_st	v1, PT_R3, \docfi
+		/*
+		 * You might think that you don't need to save $0,
+		 * but the FPU emulator and gdb remote debug stub
+		 * need it to operate correctly
+		 */
+		LONG_S	$0, PT_R0(sp)
+		mfc0	v1, CP0_STATUS
+		cfi_st	v0, PT_R2, \docfi
+		LONG_S	v1, PT_STATUS(sp)
+		cfi_st	$4, PT_R4, \docfi
+		mfc0	v1, CP0_CAUSE
+		cfi_st	$5, PT_R5, \docfi
+		LONG_S	v1, PT_CAUSE(sp)
+		cfi_st	$6, PT_R6, \docfi
+		cfi_st	ra, PT_R31, \docfi
+		MFC0	ra, CP0_EPC
+		cfi_st	$7, PT_R7, \docfi
+#ifdef CONFIG_64BIT
+		cfi_st	$8, PT_R8, \docfi
+		cfi_st	$9, PT_R9, \docfi
+#endif
+		LONG_S	ra, PT_EPC(sp)
+		.if \docfi
+		.cfi_rel_offset ra, PT_EPC
+		.endif
+		cfi_st	$25, PT_R25, \docfi
+		cfi_st	$28, PT_R28, \docfi
+
+		/* Set thread_info if we're coming from user mode */
+		mfc0	k0, CP0_STATUS
+		sll	k0, 3		/* extract cu0 bit */
+		bltz	k0, 9f
+
+		ori	$28, sp, _THREAD_MASK
+		xori	$28, _THREAD_MASK
+#ifdef CONFIG_CPU_CAVIUM_OCTEON
+		.set    mips64
+		pref    0, 0($28)       /* Prefetch the current pointer */
+#endif
+9:
+		.set	pop
+		.endm
+
+		.macro	SAVE_ALL docfi=0
+		SAVE_SOME \docfi
+		SAVE_AT \docfi
+		SAVE_TEMP \docfi
+		SAVE_STATIC \docfi
+		.endm
+
+		.macro	RESTORE_AT docfi=0
+		.set	push
+		.set	noat
+		cfi_ld	$1, PT_R1, \docfi
+		.set	pop
+		.endm
+
+		.macro	RESTORE_TEMP docfi=0
+#ifdef CONFIG_CPU_CAVIUM_OCTEON
+		/* Restore the Octeon multiplier state */
+		jal	octeon_mult_restore
+#endif
+#ifdef CONFIG_CPU_HAS_SMARTMIPS
+		LONG_L	$24, PT_ACX(sp)
+		mtlhx	$24
+		LONG_L	$24, PT_HI(sp)
+		mtlhx	$24
+		LONG_L	$24, PT_LO(sp)
+		mtlhx	$24
+#elif !defined(CONFIG_CPU_MIPSR6)
+		LONG_L	$24, PT_LO(sp)
+		mtlo	$24
+		LONG_L	$24, PT_HI(sp)
+		mthi	$24
+#endif
+#ifdef CONFIG_32BIT
+		cfi_ld	$8, PT_R8, \docfi
+		cfi_ld	$9, PT_R9, \docfi
+#endif
+		cfi_ld	$10, PT_R10, \docfi
+		cfi_ld	$11, PT_R11, \docfi
+		cfi_ld	$12, PT_R12, \docfi
+		cfi_ld	$13, PT_R13, \docfi
+		cfi_ld	$14, PT_R14, \docfi
+		cfi_ld	$15, PT_R15, \docfi
+		cfi_ld	$24, PT_R24, \docfi
+		.endm
+
+		.macro	RESTORE_STATIC docfi=0
+		cfi_ld	$16, PT_R16, \docfi
+		cfi_ld	$17, PT_R17, \docfi
+		cfi_ld	$18, PT_R18, \docfi
+		cfi_ld	$19, PT_R19, \docfi
+		cfi_ld	$20, PT_R20, \docfi
+		cfi_ld	$21, PT_R21, \docfi
+		cfi_ld	$22, PT_R22, \docfi
+		cfi_ld	$23, PT_R23, \docfi
+		cfi_ld	$30, PT_R30, \docfi
+		.endm
+
+		.macro	RESTORE_SP docfi=0
+		cfi_ld	sp, PT_R29, \docfi
+		.endm
+
+#if defined(CONFIG_CPU_R3000)
+
+		.macro	RESTORE_SOME docfi=0
+		.set	push
+		.set	reorder
+		.set	noat
+		mfc0	a0, CP0_STATUS
+		li	v1, ST0_CU1 | ST0_IM
+		ori	a0, STATMASK
+		xori	a0, STATMASK
+		mtc0	a0, CP0_STATUS
+		and	a0, v1
+		LONG_L	v0, PT_STATUS(sp)
+		nor	v1, $0, v1
+		and	v0, v1
+		or	v0, a0
+		mtc0	v0, CP0_STATUS
+		cfi_ld	$31, PT_R31, \docfi
+		cfi_ld	$28, PT_R28, \docfi
+		cfi_ld	$25, PT_R25, \docfi
+		cfi_ld	$7,  PT_R7, \docfi
+		cfi_ld	$6,  PT_R6, \docfi
+		cfi_ld	$5,  PT_R5, \docfi
+		cfi_ld	$4,  PT_R4, \docfi
+		cfi_ld	$3,  PT_R3, \docfi
+		cfi_ld	$2,  PT_R2, \docfi
+		.set	pop
+		.endm
+
+		.macro	RESTORE_SP_AND_RET docfi=0
+		.set	push
+		.set	noreorder
+		LONG_L	k0, PT_EPC(sp)
+		RESTORE_SP \docfi
+		jr	k0
+		 rfe
+		.set	pop
+		.endm
+
+#else
+		.macro	RESTORE_SOME docfi=0
+		.set	push
+		.set	reorder
+		.set	noat
+		mfc0	a0, CP0_STATUS
+		ori	a0, STATMASK
+		xori	a0, STATMASK
+		mtc0	a0, CP0_STATUS
+		li	v1, ST0_CU1 | ST0_FR | ST0_IM
+		and	a0, v1
+		LONG_L	v0, PT_STATUS(sp)
+		nor	v1, $0, v1
+		and	v0, v1
+		or	v0, a0
+		mtc0	v0, CP0_STATUS
+		LONG_L	v1, PT_EPC(sp)
+		MTC0	v1, CP0_EPC
+		cfi_ld	$31, PT_R31, \docfi
+		cfi_ld	$28, PT_R28, \docfi
+		cfi_ld	$25, PT_R25, \docfi
+#ifdef CONFIG_64BIT
+		cfi_ld	$8, PT_R8, \docfi
+		cfi_ld	$9, PT_R9, \docfi
+#endif
+		cfi_ld	$7,  PT_R7, \docfi
+		cfi_ld	$6,  PT_R6, \docfi
+		cfi_ld	$5,  PT_R5, \docfi
+		cfi_ld	$4,  PT_R4, \docfi
+		cfi_ld	$3,  PT_R3, \docfi
+		cfi_ld	$2,  PT_R2, \docfi
+		.set	pop
+		.endm
+
+		.macro	RESTORE_SP_AND_RET docfi=0
+		RESTORE_SP \docfi
+#if defined(CONFIG_CPU_MIPSR5) || defined(CONFIG_CPU_MIPSR6)
+		eretnc
+#else
+		.set	push
+		.set	arch=r4000
+		eret
+		.set	pop
+#endif
+		.endm
+
+#endif
+
+		.macro	RESTORE_ALL docfi=0
+		RESTORE_TEMP \docfi
+		RESTORE_STATIC \docfi
+		RESTORE_AT \docfi
+		RESTORE_SOME \docfi
+		RESTORE_SP \docfi
+		.endm
+
+/*
+ * Move to kernel mode and disable interrupts.
+ * Set cp0 enable bit as sign that we're running on the kernel stack
+ */
+		.macro	CLI
+		mfc0	t0, CP0_STATUS
+		li	t1, ST0_KERNEL_CUMASK | STATMASK
+		or	t0, t1
+		xori	t0, STATMASK
+		mtc0	t0, CP0_STATUS
+		irq_disable_hazard
+		.endm
+
+/*
+ * Move to kernel mode and enable interrupts.
+ * Set cp0 enable bit as sign that we're running on the kernel stack
+ */
+		.macro	STI
+		mfc0	t0, CP0_STATUS
+		li	t1, ST0_KERNEL_CUMASK | STATMASK
+		or	t0, t1
+		xori	t0, STATMASK & ~1
+		mtc0	t0, CP0_STATUS
+		irq_enable_hazard
+		.endm
+
+/*
+ * Just move to kernel mode and leave interrupts as they are.  Note
+ * for the R3000 this means copying the previous enable from IEp.
+ * Set cp0 enable bit as sign that we're running on the kernel stack
+ */
+		.macro	KMODE
+		mfc0	t0, CP0_STATUS
+		li	t1, ST0_KERNEL_CUMASK | (STATMASK & ~1)
+#if defined(CONFIG_CPU_R3000)
+		andi	t2, t0, ST0_IEP
+		srl	t2, 2
+		or	t0, t2
+#endif
+		or	t0, t1
+		xori	t0, STATMASK & ~1
+		mtc0	t0, CP0_STATUS
+		irq_disable_hazard
+		.endm
+
+#endif /* _ASM_STACKFRAME_H */
diff --git a/arch/mips/include/asm/stackprotector.h b/arch/mips/include/asm/stackprotector.h
new file mode 100644
index 000000000..68d4be9e1
--- /dev/null
+++ b/arch/mips/include/asm/stackprotector.h
@@ -0,0 +1,41 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * GCC stack protector support.
+ *
+ * (This is directly adopted from the ARM implementation)
+ *
+ * Stack protector works by putting predefined pattern at the start of
+ * the stack frame and verifying that it hasn't been overwritten when
+ * returning from the function.  The pattern is called stack canary
+ * and gcc expects it to be defined by a global variable called
+ * "__stack_chk_guard" on MIPS.  This unfortunately means that on SMP
+ * we cannot have a different canary value per task.
+ */
+
+#ifndef _ASM_STACKPROTECTOR_H
+#define _ASM_STACKPROTECTOR_H 1
+
+#include <linux/random.h>
+#include <linux/version.h>
+
+extern unsigned long __stack_chk_guard;
+
+/*
+ * Initialize the stackprotector canary value.
+ *
+ * NOTE: this must only be called from functions that never return,
+ * and it must always be inlined.
+ */
+static __always_inline void boot_init_stack_canary(void)
+{
+	unsigned long canary;
+
+	/* Try to get a semi random initial value. */
+	get_random_bytes(&canary, sizeof(canary));
+	canary ^= LINUX_VERSION_CODE;
+
+	current->stack_canary = canary;
+	__stack_chk_guard = current->stack_canary;
+}
+
+#endif	/* _ASM_STACKPROTECTOR_H */
diff --git a/arch/mips/include/asm/stacktrace.h b/arch/mips/include/asm/stacktrace.h
new file mode 100644
index 000000000..8ad25c25b
--- /dev/null
+++ b/arch/mips/include/asm/stacktrace.h
@@ -0,0 +1,89 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _ASM_STACKTRACE_H
+#define _ASM_STACKTRACE_H
+
+#include <asm/ptrace.h>
+#include <asm/asm.h>
+#include <linux/stringify.h>
+
+#ifdef CONFIG_KALLSYMS
+extern int raw_show_trace;
+extern unsigned long unwind_stack(struct task_struct *task, unsigned long *sp,
+				  unsigned long pc, unsigned long *ra);
+extern unsigned long unwind_stack_by_address(unsigned long stack_page,
+					     unsigned long *sp,
+					     unsigned long pc,
+					     unsigned long *ra);
+#else
+#define raw_show_trace 1
+static inline unsigned long unwind_stack(struct task_struct *task,
+	unsigned long *sp, unsigned long pc, unsigned long *ra)
+{
+	return 0;
+}
+#endif
+
+#define STR_PTR_LA    __stringify(PTR_LA)
+#define STR_LONG_S    __stringify(LONG_S)
+#define STR_LONG_L    __stringify(LONG_L)
+#define STR_LONGSIZE  __stringify(LONGSIZE)
+
+#define STORE_ONE_REG(r) \
+    STR_LONG_S   " $" __stringify(r)",("STR_LONGSIZE"*"__stringify(r)")(%1)\n\t"
+
+static __always_inline void prepare_frametrace(struct pt_regs *regs)
+{
+#ifndef CONFIG_KALLSYMS
+	/*
+	 * Remove any garbage that may be in regs (specially func
+	 * addresses) to avoid show_raw_backtrace() to report them
+	 */
+	memset(regs, 0, sizeof(*regs));
+#endif
+	__asm__ __volatile__(
+		".set push\n\t"
+		".set noat\n\t"
+		/* Store $1 so we can use it */
+		STR_LONG_S " $1,"STR_LONGSIZE"(%1)\n\t"
+		/* Store the PC */
+		"1: " STR_PTR_LA " $1, 1b\n\t"
+		STR_LONG_S " $1,%0\n\t"
+		STORE_ONE_REG(2)
+		STORE_ONE_REG(3)
+		STORE_ONE_REG(4)
+		STORE_ONE_REG(5)
+		STORE_ONE_REG(6)
+		STORE_ONE_REG(7)
+		STORE_ONE_REG(8)
+		STORE_ONE_REG(9)
+		STORE_ONE_REG(10)
+		STORE_ONE_REG(11)
+		STORE_ONE_REG(12)
+		STORE_ONE_REG(13)
+		STORE_ONE_REG(14)
+		STORE_ONE_REG(15)
+		STORE_ONE_REG(16)
+		STORE_ONE_REG(17)
+		STORE_ONE_REG(18)
+		STORE_ONE_REG(19)
+		STORE_ONE_REG(20)
+		STORE_ONE_REG(21)
+		STORE_ONE_REG(22)
+		STORE_ONE_REG(23)
+		STORE_ONE_REG(24)
+		STORE_ONE_REG(25)
+		STORE_ONE_REG(26)
+		STORE_ONE_REG(27)
+		STORE_ONE_REG(28)
+		STORE_ONE_REG(29)
+		STORE_ONE_REG(30)
+		STORE_ONE_REG(31)
+		/* Restore $1 */
+		STR_LONG_L " $1,"STR_LONGSIZE"(%1)\n\t"
+		".set pop\n\t"
+		: "=m" (regs->cp0_epc)
+		: "r" (regs->regs)
+		: "memory");
+}
+
+#endif /* _ASM_STACKTRACE_H */
diff --git a/arch/mips/include/asm/string.h b/arch/mips/include/asm/string.h
new file mode 100644
index 000000000..1de3bbce8
--- /dev/null
+++ b/arch/mips/include/asm/string.h
@@ -0,0 +1,22 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (c) 1994, 95, 96, 97, 98, 2000, 01 Ralf Baechle
+ * Copyright (c) 2000 by Silicon Graphics, Inc.
+ * Copyright (c) 2001 MIPS Technologies, Inc.
+ */
+#ifndef _ASM_STRING_H
+#define _ASM_STRING_H
+
+#define __HAVE_ARCH_MEMSET
+extern void *memset(void *__s, int __c, size_t __count);
+
+#define __HAVE_ARCH_MEMCPY
+extern void *memcpy(void *__to, __const__ void *__from, size_t __n);
+
+#define __HAVE_ARCH_MEMMOVE
+extern void *memmove(void *__dest, __const__ void *__src, size_t __n);
+
+#endif /* _ASM_STRING_H */
diff --git a/arch/mips/include/asm/switch_to.h b/arch/mips/include/asm/switch_to.h
new file mode 100644
index 000000000..a4374b4cb
--- /dev/null
+++ b/arch/mips/include/asm/switch_to.h
@@ -0,0 +1,142 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994, 95, 96, 97, 98, 99, 2003, 06 by Ralf Baechle
+ * Copyright (C) 1996 by Paul M. Antoine
+ * Copyright (C) 1999 Silicon Graphics
+ * Kevin D. Kissell, kevink@mips.org and Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 2000 MIPS Technologies, Inc.
+ */
+#ifndef _ASM_SWITCH_TO_H
+#define _ASM_SWITCH_TO_H
+
+#include <asm/cpu-features.h>
+#include <asm/watch.h>
+#include <asm/dsp.h>
+#include <asm/cop2.h>
+#include <asm/fpu.h>
+
+struct task_struct;
+
+/**
+ * resume - resume execution of a task
+ * @prev:	The task previously executed.
+ * @next:	The task to begin executing.
+ * @next_ti:	task_thread_info(next).
+ *
+ * This function is used whilst scheduling to save the context of prev & load
+ * the context of next. Returns prev.
+ */
+extern asmlinkage struct task_struct *resume(struct task_struct *prev,
+		struct task_struct *next, struct thread_info *next_ti);
+
+extern unsigned int ll_bit;
+extern struct task_struct *ll_task;
+
+#ifdef CONFIG_MIPS_MT_FPAFF
+
+/*
+ * Handle the scheduler resume end of FPU affinity management.	We do this
+ * inline to try to keep the overhead down. If we have been forced to run on
+ * a "CPU" with an FPU because of a previous high level of FP computation,
+ * but did not actually use the FPU during the most recent time-slice (CU1
+ * isn't set), we undo the restriction on cpus_mask.
+ *
+ * We're not calling set_cpus_allowed() here, because we have no need to
+ * force prompt migration - we're already switching the current CPU to a
+ * different thread.
+ */
+
+#define __mips_mt_fpaff_switch_to(prev)					\
+do {									\
+	struct thread_info *__prev_ti = task_thread_info(prev);		\
+									\
+	if (cpu_has_fpu &&						\
+	    test_ti_thread_flag(__prev_ti, TIF_FPUBOUND) &&		\
+	    (!(KSTK_STATUS(prev) & ST0_CU1))) {				\
+		clear_ti_thread_flag(__prev_ti, TIF_FPUBOUND);		\
+		prev->cpus_mask = prev->thread.user_cpus_allowed;	\
+	}								\
+	next->thread.emulated_fp = 0;					\
+} while(0)
+
+#else
+#define __mips_mt_fpaff_switch_to(prev) do { (void) (prev); } while (0)
+#endif
+
+/*
+ * Clear LLBit during context switches on MIPSr5+ such that eretnc can be used
+ * unconditionally when returning to userland in entry.S.
+ */
+#define __clear_r5_hw_ll_bit() do {					\
+	if (cpu_has_mips_r5 || cpu_has_mips_r6)				\
+		write_c0_lladdr(0);					\
+} while (0)
+
+#define __clear_software_ll_bit() do {					\
+	if (!__builtin_constant_p(cpu_has_llsc) || !cpu_has_llsc)	\
+		ll_bit = 0;						\
+} while (0)
+
+/*
+ * Check FCSR for any unmasked exceptions pending set with `ptrace',
+ * clear them and send a signal.
+ */
+#ifdef CONFIG_MIPS_FP_SUPPORT
+# define __sanitize_fcr31(next)						\
+do {									\
+	unsigned long fcr31 = mask_fcr31_x(next->thread.fpu.fcr31);	\
+	void __user *pc;						\
+									\
+	if (unlikely(fcr31)) {						\
+		pc = (void __user *)task_pt_regs(next)->cp0_epc;	\
+		next->thread.fpu.fcr31 &= ~fcr31;			\
+		force_fcr31_sig(fcr31, pc, next);			\
+	}								\
+} while (0)
+#else
+# define __sanitize_fcr31(next)
+#endif
+
+/*
+ * For newly created kernel threads switch_to() will return to
+ * ret_from_kernel_thread, newly created user threads to ret_from_fork.
+ * That is, everything following resume() will be skipped for new threads.
+ * So everything that matters to new threads should be placed before resume().
+ */
+#define switch_to(prev, next, last)					\
+do {									\
+	__mips_mt_fpaff_switch_to(prev);				\
+	lose_fpu_inatomic(1, prev);					\
+	if (tsk_used_math(next))					\
+		__sanitize_fcr31(next);					\
+	if (cpu_has_dsp) {						\
+		__save_dsp(prev);					\
+		__restore_dsp(next);					\
+	}								\
+	if (cop2_present) {						\
+		u32 status = read_c0_status();				\
+									\
+		set_c0_status(ST0_CU2);					\
+		if ((KSTK_STATUS(prev) & ST0_CU2)) {			\
+			if (cop2_lazy_restore)				\
+				KSTK_STATUS(prev) &= ~ST0_CU2;		\
+			cop2_save(prev);				\
+		}							\
+		if (KSTK_STATUS(next) & ST0_CU2 &&			\
+		    !cop2_lazy_restore) {				\
+			cop2_restore(next);				\
+		}							\
+		write_c0_status(status);				\
+	}								\
+	__clear_r5_hw_ll_bit();						\
+	__clear_software_ll_bit();					\
+	if (cpu_has_userlocal)						\
+		write_c0_userlocal(task_thread_info(next)->tp_value);	\
+	__restore_watch(next);						\
+	(last) = resume(prev, next, task_thread_info(next));		\
+} while (0)
+
+#endif /* _ASM_SWITCH_TO_H */
diff --git a/arch/mips/include/asm/sync.h b/arch/mips/include/asm/sync.h
new file mode 100644
index 000000000..aabd09793
--- /dev/null
+++ b/arch/mips/include/asm/sync.h
@@ -0,0 +1,209 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+#ifndef __MIPS_ASM_SYNC_H__
+#define __MIPS_ASM_SYNC_H__
+
+/*
+ * sync types are defined by the MIPS64 Instruction Set documentation in Volume
+ * II-A of the MIPS Architecture Reference Manual, which can be found here:
+ *
+ *   https://www.mips.com/?do-download=the-mips64-instruction-set-v6-06
+ *
+ * Two types of barrier are provided:
+ *
+ *   1) Completion barriers, which ensure that a memory operation has actually
+ *      completed & often involve stalling the CPU pipeline to do so.
+ *
+ *   2) Ordering barriers, which only ensure that affected memory operations
+ *      won't be reordered in the CPU pipeline in a manner that violates the
+ *      restrictions imposed by the barrier.
+ *
+ * Ordering barriers can be more efficient than completion barriers, since:
+ *
+ *   a) Ordering barriers only require memory access instructions which preceed
+ *      them in program order (older instructions) to reach a point in the
+ *      load/store datapath beyond which reordering is not possible before
+ *      allowing memory access instructions which follow them (younger
+ *      instructions) to be performed.  That is, older instructions don't
+ *      actually need to complete - they just need to get far enough that all
+ *      other coherent CPUs will observe their completion before they observe
+ *      the effects of younger instructions.
+ *
+ *   b) Multiple variants of ordering barrier are provided which allow the
+ *      effects to be restricted to different combinations of older or younger
+ *      loads or stores. By way of example, if we only care that stores older
+ *      than a barrier are observed prior to stores that are younger than a
+ *      barrier & don't care about the ordering of loads then the 'wmb'
+ *      ordering barrier can be used. Limiting the barrier's effects to stores
+ *      allows loads to continue unaffected & potentially allows the CPU to
+ *      make progress faster than if younger loads had to wait for older stores
+ *      to complete.
+ */
+
+/*
+ * No sync instruction at all; used to allow code to nullify the effect of the
+ * __SYNC() macro without needing lots of #ifdefery.
+ */
+#define __SYNC_none	-1
+
+/*
+ * A full completion barrier; all memory accesses appearing prior to this sync
+ * instruction in program order must complete before any memory accesses
+ * appearing after this sync instruction in program order.
+ */
+#define __SYNC_full	0x00
+
+/*
+ * For now we use a full completion barrier to implement all sync types, until
+ * we're satisfied that lightweight ordering barriers defined by MIPSr6 are
+ * sufficient to uphold our desired memory model.
+ */
+#define __SYNC_aq	__SYNC_full
+#define __SYNC_rl	__SYNC_full
+#define __SYNC_mb	__SYNC_full
+
+/*
+ * ...except on Cavium Octeon CPUs, which have been using the 'wmb' ordering
+ * barrier since 2010 & omit 'rmb' barriers because the CPUs don't perform
+ * speculative reads.
+ */
+#ifdef CONFIG_CPU_CAVIUM_OCTEON
+# define __SYNC_rmb	__SYNC_none
+# define __SYNC_wmb	0x04
+#else
+# define __SYNC_rmb	__SYNC_full
+# define __SYNC_wmb	__SYNC_full
+#endif
+
+/*
+ * A GINV sync is a little different; it doesn't relate directly to loads or
+ * stores, but instead causes synchronization of an icache or TLB global
+ * invalidation operation triggered by the ginvi or ginvt instructions
+ * respectively. In cases where we need to know that a ginvi or ginvt operation
+ * has been performed by all coherent CPUs, we must issue a sync instruction of
+ * this type. Once this instruction graduates all coherent CPUs will have
+ * observed the invalidation.
+ */
+#define __SYNC_ginv	0x14
+
+/* Trivial; indicate that we always need this sync instruction. */
+#define __SYNC_always	(1 << 0)
+
+/*
+ * Indicate that we need this sync instruction only on systems with weakly
+ * ordered memory access. In general this is most MIPS systems, but there are
+ * exceptions which provide strongly ordered memory.
+ */
+#ifdef CONFIG_WEAK_ORDERING
+# define __SYNC_weak_ordering	(1 << 1)
+#else
+# define __SYNC_weak_ordering	0
+#endif
+
+/*
+ * Indicate that we need this sync instruction only on systems where LL/SC
+ * don't implicitly provide a memory barrier. In general this is most MIPS
+ * systems.
+ */
+#ifdef CONFIG_WEAK_REORDERING_BEYOND_LLSC
+# define __SYNC_weak_llsc	(1 << 2)
+#else
+# define __SYNC_weak_llsc	0
+#endif
+
+/*
+ * Some Loongson 3 CPUs have a bug wherein execution of a memory access (load,
+ * store or prefetch) in between an LL & SC can cause the SC instruction to
+ * erroneously succeed, breaking atomicity. Whilst it's unusual to write code
+ * containing such sequences, this bug bites harder than we might otherwise
+ * expect due to reordering & speculation:
+ *
+ * 1) A memory access appearing prior to the LL in program order may actually
+ *    be executed after the LL - this is the reordering case.
+ *
+ *    In order to avoid this we need to place a memory barrier (ie. a SYNC
+ *    instruction) prior to every LL instruction, in between it and any earlier
+ *    memory access instructions.
+ *
+ *    This reordering case is fixed by 3A R2 CPUs, ie. 3A2000 models and later.
+ *
+ * 2) If a conditional branch exists between an LL & SC with a target outside
+ *    of the LL-SC loop, for example an exit upon value mismatch in cmpxchg()
+ *    or similar, then misprediction of the branch may allow speculative
+ *    execution of memory accesses from outside of the LL-SC loop.
+ *
+ *    In order to avoid this we need a memory barrier (ie. a SYNC instruction)
+ *    at each affected branch target.
+ *
+ *    This case affects all current Loongson 3 CPUs.
+ *
+ * The above described cases cause an error in the cache coherence protocol;
+ * such that the Invalidate of a competing LL-SC goes 'missing' and SC
+ * erroneously observes its core still has Exclusive state and lets the SC
+ * proceed.
+ *
+ * Therefore the error only occurs on SMP systems.
+ */
+#ifdef CONFIG_CPU_LOONGSON3_WORKAROUNDS
+# define __SYNC_loongson3_war	(1 << 31)
+#else
+# define __SYNC_loongson3_war	0
+#endif
+
+/*
+ * Some Cavium Octeon CPUs suffer from a bug that causes a single wmb ordering
+ * barrier to be ineffective, requiring the use of 2 in sequence to provide an
+ * effective barrier as noted by commit 6b07d38aaa52 ("MIPS: Octeon: Use
+ * optimized memory barrier primitives."). Here we specify that the affected
+ * sync instructions should be emitted twice.
+ * Note that this expression is evaluated by the assembler (not the compiler),
+ * and that the assembler evaluates '==' as 0 or -1, not 0 or 1.
+ */
+#ifdef CONFIG_CPU_CAVIUM_OCTEON
+# define __SYNC_rpt(type)	(1 - (type == __SYNC_wmb))
+#else
+# define __SYNC_rpt(type)	1
+#endif
+
+/*
+ * The main event. Here we actually emit a sync instruction of a given type, if
+ * reason is non-zero.
+ *
+ * In future we have the option of emitting entries in a fixups-style table
+ * here that would allow us to opportunistically remove some sync instructions
+ * when we detect at runtime that we're running on a CPU that doesn't need
+ * them.
+ */
+#ifdef CONFIG_CPU_HAS_SYNC
+# define ____SYNC(_type, _reason, _else)			\
+	.if	(( _type ) != -1) && ( _reason );		\
+	.set	push;						\
+	.set	MIPS_ISA_LEVEL_RAW;				\
+	.rept	__SYNC_rpt(_type);				\
+	sync	_type;						\
+	.endr;							\
+	.set	pop;						\
+	.else;							\
+	_else;							\
+	.endif
+#else
+# define ____SYNC(_type, _reason, _else)
+#endif
+
+/*
+ * Preprocessor magic to expand macros used as arguments before we insert them
+ * into assembly code.
+ */
+#ifdef __ASSEMBLY__
+# define ___SYNC(type, reason, else)				\
+	____SYNC(type, reason, else)
+#else
+# define ___SYNC(type, reason, else)				\
+	__stringify(____SYNC(type, reason, else))
+#endif
+
+#define __SYNC(type, reason)					\
+	___SYNC(__SYNC_##type, __SYNC_##reason, )
+#define __SYNC_ELSE(type, reason, else)				\
+	___SYNC(__SYNC_##type, __SYNC_##reason, else)
+
+#endif /* __MIPS_ASM_SYNC_H__ */
diff --git a/arch/mips/include/asm/syscall.h b/arch/mips/include/asm/syscall.h
new file mode 100644
index 000000000..ebdf4d910
--- /dev/null
+++ b/arch/mips/include/asm/syscall.h
@@ -0,0 +1,160 @@
+/*
+ * Access to user system call parameters and results
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * See asm-generic/syscall.h for descriptions of what we must do here.
+ *
+ * Copyright (C) 2012 Ralf Baechle <ralf@linux-mips.org>
+ */
+
+#ifndef __ASM_MIPS_SYSCALL_H
+#define __ASM_MIPS_SYSCALL_H
+
+#include <linux/compiler.h>
+#include <uapi/linux/audit.h>
+#include <linux/elf-em.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/uaccess.h>
+#include <asm/ptrace.h>
+#include <asm/unistd.h>
+
+#ifndef __NR_syscall /* Only defined if _MIPS_SIM == _MIPS_SIM_ABI32 */
+#define __NR_syscall 4000
+#endif
+
+static inline bool mips_syscall_is_indirect(struct task_struct *task,
+					    struct pt_regs *regs)
+{
+	/* O32 ABI syscall() - Either 64-bit with O32 or 32-bit */
+	return (IS_ENABLED(CONFIG_32BIT) ||
+		test_tsk_thread_flag(task, TIF_32BIT_REGS)) &&
+		(regs->regs[2] == __NR_syscall);
+}
+
+static inline long syscall_get_nr(struct task_struct *task,
+				  struct pt_regs *regs)
+{
+	return task_thread_info(task)->syscall;
+}
+
+static inline void mips_syscall_update_nr(struct task_struct *task,
+					  struct pt_regs *regs)
+{
+	/*
+	 * v0 is the system call number, except for O32 ABI syscall(), where it
+	 * ends up in a0.
+	 */
+	if (mips_syscall_is_indirect(task, regs))
+		task_thread_info(task)->syscall = regs->regs[4];
+	else
+		task_thread_info(task)->syscall = regs->regs[2];
+}
+
+static inline void mips_get_syscall_arg(unsigned long *arg,
+	struct task_struct *task, struct pt_regs *regs, unsigned int n)
+{
+	unsigned long usp __maybe_unused = regs->regs[29];
+
+	switch (n) {
+	case 0: case 1: case 2: case 3:
+		*arg = regs->regs[4 + n];
+
+		return;
+
+#ifdef CONFIG_32BIT
+	case 4: case 5: case 6: case 7:
+		get_user(*arg, (int *)usp + n);
+		return;
+#endif
+
+#ifdef CONFIG_64BIT
+	case 4: case 5: case 6: case 7:
+#ifdef CONFIG_MIPS32_O32
+		if (test_tsk_thread_flag(task, TIF_32BIT_REGS))
+			get_user(*arg, (int *)usp + n);
+		else
+#endif
+			*arg = regs->regs[4 + n];
+
+		return;
+#endif
+
+	default:
+		BUG();
+	}
+
+	unreachable();
+}
+
+static inline long syscall_get_error(struct task_struct *task,
+				     struct pt_regs *regs)
+{
+	return regs->regs[7] ? -regs->regs[2] : 0;
+}
+
+static inline long syscall_get_return_value(struct task_struct *task,
+					    struct pt_regs *regs)
+{
+	return regs->regs[2];
+}
+
+static inline void syscall_rollback(struct task_struct *task,
+				    struct pt_regs *regs)
+{
+	/* Do nothing */
+}
+
+static inline void syscall_set_return_value(struct task_struct *task,
+					    struct pt_regs *regs,
+					    int error, long val)
+{
+	if (error) {
+		regs->regs[2] = -error;
+		regs->regs[7] = 1;
+	} else {
+		regs->regs[2] = val;
+		regs->regs[7] = 0;
+	}
+}
+
+static inline void syscall_get_arguments(struct task_struct *task,
+					 struct pt_regs *regs,
+					 unsigned long *args)
+{
+	unsigned int i = 0;
+	unsigned int n = 6;
+
+	/* O32 ABI syscall() */
+	if (mips_syscall_is_indirect(task, regs))
+		i++;
+
+	while (n--)
+		mips_get_syscall_arg(args++, task, regs, i++);
+}
+
+extern const unsigned long sys_call_table[];
+extern const unsigned long sys32_call_table[];
+extern const unsigned long sysn32_call_table[];
+
+static inline int syscall_get_arch(struct task_struct *task)
+{
+	int arch = AUDIT_ARCH_MIPS;
+#ifdef CONFIG_64BIT
+	if (!test_tsk_thread_flag(task, TIF_32BIT_REGS)) {
+		arch |= __AUDIT_ARCH_64BIT;
+		/* N32 sets only TIF_32BIT_ADDR */
+		if (test_tsk_thread_flag(task, TIF_32BIT_ADDR))
+			arch |= __AUDIT_ARCH_CONVENTION_MIPS64_N32;
+	}
+#endif
+#if defined(__LITTLE_ENDIAN)
+	arch |=  __AUDIT_ARCH_LE;
+#endif
+	return arch;
+}
+
+#endif	/* __ASM_MIPS_SYSCALL_H */
diff --git a/arch/mips/include/asm/thread_info.h b/arch/mips/include/asm/thread_info.h
new file mode 100644
index 000000000..ecae7470f
--- /dev/null
+++ b/arch/mips/include/asm/thread_info.h
@@ -0,0 +1,197 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* thread_info.h: MIPS low-level thread information
+ *
+ * Copyright (C) 2002  David Howells (dhowells@redhat.com)
+ * - Incorporating suggestions made by Linus Torvalds and Dave Miller
+ */
+
+#ifndef _ASM_THREAD_INFO_H
+#define _ASM_THREAD_INFO_H
+
+#ifdef __KERNEL__
+
+
+#ifndef __ASSEMBLY__
+
+#include <asm/processor.h>
+
+/*
+ * low level task data that entry.S needs immediate access to
+ * - this struct should fit entirely inside of one cache line
+ * - this struct shares the supervisor stack pages
+ * - if the contents of this structure are changed, the assembly constants
+ *   must also be changed
+ */
+struct thread_info {
+	struct task_struct	*task;		/* main task structure */
+	unsigned long		flags;		/* low level flags */
+	unsigned long		tp_value;	/* thread pointer */
+	__u32			cpu;		/* current CPU */
+	int			preempt_count;	/* 0 => preemptable, <0 => BUG */
+	struct pt_regs		*regs;
+	long			syscall;	/* syscall number */
+};
+
+/*
+ * macros/functions for gaining access to the thread information structure
+ */
+#define INIT_THREAD_INFO(tsk)			\
+{						\
+	.task		= &tsk,			\
+	.flags		= _TIF_FIXADE,		\
+	.cpu		= 0,			\
+	.preempt_count	= INIT_PREEMPT_COUNT,	\
+}
+
+/*
+ * A pointer to the struct thread_info for the currently executing thread is
+ * held in register $28/$gp.
+ *
+ * We declare __current_thread_info as a global register variable rather than a
+ * local register variable within current_thread_info() because clang doesn't
+ * support explicit local register variables.
+ *
+ * When building the VDSO we take care not to declare the global register
+ * variable because this causes GCC to not preserve the value of $28/$gp in
+ * functions that change its value (which is common in the PIC VDSO when
+ * accessing the GOT). Since the VDSO shouldn't be accessing
+ * __current_thread_info anyway we declare it extern in order to cause a link
+ * failure if it's referenced.
+ */
+#ifdef __VDSO__
+extern struct thread_info *__current_thread_info;
+#else
+register struct thread_info *__current_thread_info __asm__("$28");
+#endif
+
+static inline struct thread_info *current_thread_info(void)
+{
+	return __current_thread_info;
+}
+
+#ifdef CONFIG_ARCH_HAS_CURRENT_STACK_POINTER
+register unsigned long current_stack_pointer __asm__("sp");
+#endif
+
+#endif /* !__ASSEMBLY__ */
+
+/* thread information allocation */
+#if defined(CONFIG_PAGE_SIZE_4KB) && defined(CONFIG_32BIT)
+#define THREAD_SIZE_ORDER (1)
+#endif
+#if defined(CONFIG_PAGE_SIZE_4KB) && defined(CONFIG_64BIT)
+#define THREAD_SIZE_ORDER (2)
+#endif
+#ifdef CONFIG_PAGE_SIZE_8KB
+#define THREAD_SIZE_ORDER (1)
+#endif
+#ifdef CONFIG_PAGE_SIZE_16KB
+#define THREAD_SIZE_ORDER (0)
+#endif
+#ifdef CONFIG_PAGE_SIZE_32KB
+#define THREAD_SIZE_ORDER (0)
+#endif
+#ifdef CONFIG_PAGE_SIZE_64KB
+#define THREAD_SIZE_ORDER (0)
+#endif
+
+#define THREAD_SIZE (PAGE_SIZE << THREAD_SIZE_ORDER)
+#define THREAD_MASK (THREAD_SIZE - 1UL)
+
+#define STACK_WARN	(THREAD_SIZE / 8)
+
+/*
+ * thread information flags
+ * - these are process state flags that various assembly files may need to
+ *   access
+ * - pending work-to-be-done flags are in LSW
+ * - other flags in MSW
+ */
+#define TIF_SIGPENDING		1	/* signal pending */
+#define TIF_NEED_RESCHED	2	/* rescheduling necessary */
+#define TIF_SYSCALL_AUDIT	3	/* syscall auditing active */
+#define TIF_SECCOMP		4	/* secure computing */
+#define TIF_NOTIFY_RESUME	5	/* callback before returning to user */
+#define TIF_UPROBE		6	/* breakpointed or singlestepping */
+#define TIF_NOTIFY_SIGNAL	7	/* signal notifications exist */
+#define TIF_RESTORE_SIGMASK	9	/* restore signal mask in do_signal() */
+#define TIF_USEDFPU		16	/* FPU was used by this task this quantum (SMP) */
+#define TIF_MEMDIE		18	/* is terminating due to OOM killer */
+#define TIF_NOHZ		19	/* in adaptive nohz mode */
+#define TIF_FIXADE		20	/* Fix address errors in software */
+#define TIF_LOGADE		21	/* Log address errors to syslog */
+#define TIF_32BIT_REGS		22	/* 32-bit general purpose registers */
+#define TIF_32BIT_ADDR		23	/* 32-bit address space (o32/n32) */
+#define TIF_FPUBOUND		24	/* thread bound to FPU-full CPU set */
+#define TIF_LOAD_WATCH		25	/* If set, load watch registers */
+#define TIF_SYSCALL_TRACEPOINT	26	/* syscall tracepoint instrumentation */
+#define TIF_32BIT_FPREGS	27	/* 32-bit floating point registers */
+#define TIF_HYBRID_FPREGS	28	/* 64b FP registers, odd singles in bits 63:32 of even doubles */
+#define TIF_USEDMSA		29	/* MSA has been used this quantum */
+#define TIF_MSA_CTX_LIVE	30	/* MSA context must be preserved */
+#define TIF_SYSCALL_TRACE	31	/* syscall trace active */
+
+#define _TIF_SYSCALL_TRACE	(1<<TIF_SYSCALL_TRACE)
+#define _TIF_SIGPENDING		(1<<TIF_SIGPENDING)
+#define _TIF_NEED_RESCHED	(1<<TIF_NEED_RESCHED)
+#define _TIF_SYSCALL_AUDIT	(1<<TIF_SYSCALL_AUDIT)
+#define _TIF_SECCOMP		(1<<TIF_SECCOMP)
+#define _TIF_NOTIFY_RESUME	(1<<TIF_NOTIFY_RESUME)
+#define _TIF_UPROBE		(1<<TIF_UPROBE)
+#define _TIF_NOTIFY_SIGNAL	(1<<TIF_NOTIFY_SIGNAL)
+#define _TIF_USEDFPU		(1<<TIF_USEDFPU)
+#define _TIF_NOHZ		(1<<TIF_NOHZ)
+#define _TIF_FIXADE		(1<<TIF_FIXADE)
+#define _TIF_LOGADE		(1<<TIF_LOGADE)
+#define _TIF_32BIT_REGS		(1<<TIF_32BIT_REGS)
+#define _TIF_32BIT_ADDR		(1<<TIF_32BIT_ADDR)
+#define _TIF_FPUBOUND		(1<<TIF_FPUBOUND)
+#define _TIF_LOAD_WATCH		(1<<TIF_LOAD_WATCH)
+#define _TIF_32BIT_FPREGS	(1<<TIF_32BIT_FPREGS)
+#define _TIF_HYBRID_FPREGS	(1<<TIF_HYBRID_FPREGS)
+#define _TIF_USEDMSA		(1<<TIF_USEDMSA)
+#define _TIF_MSA_CTX_LIVE	(1<<TIF_MSA_CTX_LIVE)
+#define _TIF_SYSCALL_TRACEPOINT	(1<<TIF_SYSCALL_TRACEPOINT)
+
+#define _TIF_WORK_SYSCALL_ENTRY	(_TIF_NOHZ | _TIF_SYSCALL_TRACE |	\
+				 _TIF_SYSCALL_AUDIT | \
+				 _TIF_SYSCALL_TRACEPOINT | _TIF_SECCOMP)
+
+/* work to do in syscall_trace_leave() */
+#define _TIF_WORK_SYSCALL_EXIT	(_TIF_NOHZ | _TIF_SYSCALL_TRACE |	\
+				 _TIF_SYSCALL_AUDIT | _TIF_SYSCALL_TRACEPOINT)
+
+/* work to do on interrupt/exception return */
+#define _TIF_WORK_MASK		\
+	(_TIF_SIGPENDING | _TIF_NEED_RESCHED | _TIF_NOTIFY_RESUME |	\
+	 _TIF_UPROBE | _TIF_NOTIFY_SIGNAL)
+/* work to do on any return to u-space */
+#define _TIF_ALLWORK_MASK	(_TIF_NOHZ | _TIF_WORK_MASK |		\
+				 _TIF_WORK_SYSCALL_EXIT |		\
+				 _TIF_SYSCALL_TRACEPOINT)
+
+/*
+ * We stash processor id into a COP0 register to retrieve it fast
+ * at kernel exception entry.
+ */
+#if   defined(CONFIG_MIPS_PGD_C0_CONTEXT)
+#define SMP_CPUID_REG		20, 0	/* XCONTEXT */
+#define ASM_SMP_CPUID_REG	$20
+#define SMP_CPUID_PTRSHIFT	48
+#else
+#define SMP_CPUID_REG		4, 0	/* CONTEXT */
+#define ASM_SMP_CPUID_REG	$4
+#define SMP_CPUID_PTRSHIFT	23
+#endif
+
+#ifdef CONFIG_64BIT
+#define SMP_CPUID_REGSHIFT	(SMP_CPUID_PTRSHIFT + 3)
+#else
+#define SMP_CPUID_REGSHIFT	(SMP_CPUID_PTRSHIFT + 2)
+#endif
+
+#define ASM_CPUID_MFC0		MFC0
+#define UASM_i_CPUID_MFC0	UASM_i_MFC0
+
+#endif /* __KERNEL__ */
+#endif /* _ASM_THREAD_INFO_H */
diff --git a/arch/mips/include/asm/time.h b/arch/mips/include/asm/time.h
new file mode 100644
index 000000000..e855a3611
--- /dev/null
+++ b/arch/mips/include/asm/time.h
@@ -0,0 +1,73 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2001, 2002, MontaVista Software Inc.
+ * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net
+ * Copyright (c) 2003  Maciej W. Rozycki
+ *
+ * include/asm-mips/time.h
+ *     header file for the new style time.c file and time services.
+ */
+#ifndef _ASM_TIME_H
+#define _ASM_TIME_H
+
+#include <linux/rtc.h>
+#include <linux/spinlock.h>
+#include <linux/clockchips.h>
+#include <linux/clocksource.h>
+
+extern spinlock_t rtc_lock;
+
+/*
+ * board specific routines required by time_init().
+ */
+extern void plat_time_init(void);
+
+/*
+ * mips_hpt_frequency - must be set if you intend to use an R4k-compatible
+ * counter as a timer interrupt source.
+ */
+extern unsigned int mips_hpt_frequency;
+
+/*
+ * The performance counter IRQ on MIPS is a close relative to the timer IRQ
+ * so it lives here.
+ */
+extern int (*perf_irq)(void);
+extern int __weak get_c0_perfcount_int(void);
+
+/*
+ * Initialize the calling CPU's compare interrupt as clockevent device
+ */
+extern unsigned int get_c0_compare_int(void);
+extern int r4k_clockevent_init(void);
+
+static inline int mips_clockevent_init(void)
+{
+#ifdef CONFIG_CEVT_R4K
+	return r4k_clockevent_init();
+#else
+	return -ENXIO;
+#endif
+}
+
+/*
+ * Initialize the count register as a clocksource
+ */
+extern int init_r4k_clocksource(void);
+
+static inline int init_mips_clocksource(void)
+{
+#ifdef CONFIG_CSRC_R4K
+	return init_r4k_clocksource();
+#else
+	return 0;
+#endif
+}
+
+static inline void clockevent_set_clock(struct clock_event_device *cd,
+					unsigned int clock)
+{
+	clockevents_calc_mult_shift(cd, clock, 4);
+}
+
+#endif /* _ASM_TIME_H */
diff --git a/arch/mips/include/asm/timex.h b/arch/mips/include/asm/timex.h
new file mode 100644
index 000000000..2e107886f
--- /dev/null
+++ b/arch/mips/include/asm/timex.h
@@ -0,0 +1,102 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1998, 1999, 2003 by Ralf Baechle
+ * Copyright (C) 2014 by Maciej W. Rozycki
+ */
+#ifndef _ASM_TIMEX_H
+#define _ASM_TIMEX_H
+
+#ifdef __KERNEL__
+
+#include <linux/compiler.h>
+
+#include <asm/cpu.h>
+#include <asm/cpu-features.h>
+#include <asm/mipsregs.h>
+#include <asm/cpu-type.h>
+
+/*
+ * This is the clock rate of the i8253 PIT.  A MIPS system may not have
+ * a PIT by the symbol is used all over the kernel including some APIs.
+ * So keeping it defined to the number for the PIT is the only sane thing
+ * for now.
+ */
+#define CLOCK_TICK_RATE 1193182
+
+/*
+ * Standard way to access the cycle counter.
+ * Currently only used on SMP for scheduling.
+ *
+ * Only the low 32 bits are available as a continuously counting entity.
+ * But this only means we'll force a reschedule every 8 seconds or so,
+ * which isn't an evil thing.
+ *
+ * We know that all SMP capable CPUs have cycle counters.
+ */
+
+typedef unsigned int cycles_t;
+
+/*
+ * On R4000/R4400 an erratum exists such that if the cycle counter is
+ * read in the exact moment that it is matching the compare register,
+ * no interrupt will be generated.
+ *
+ * There is a suggested workaround and also the erratum can't strike if
+ * the compare interrupt isn't being used as the clock source device.
+ * However for now the implementaton of this function doesn't get these
+ * fine details right.
+ */
+static inline int can_use_mips_counter(unsigned int prid)
+{
+	int comp = (prid & PRID_COMP_MASK) != PRID_COMP_LEGACY;
+
+	if (__builtin_constant_p(cpu_has_counter) && !cpu_has_counter)
+		return 0;
+	else if (__builtin_constant_p(cpu_has_mips_r) && cpu_has_mips_r)
+		return 1;
+	else if (likely(!__builtin_constant_p(cpu_has_mips_r) && comp))
+		return 1;
+	/* Make sure we don't peek at cpu_data[0].options in the fast path! */
+	if (!__builtin_constant_p(cpu_has_counter))
+		asm volatile("" : "=m" (cpu_data[0].options));
+	if (likely(cpu_has_counter &&
+		   prid > (PRID_IMP_R4000 | PRID_REV_ENCODE_44(15, 15))))
+		return 1;
+	else
+		return 0;
+}
+
+static inline cycles_t get_cycles(void)
+{
+	if (can_use_mips_counter(read_c0_prid()))
+		return read_c0_count();
+	else
+		return 0;	/* no usable counter */
+}
+#define get_cycles get_cycles
+
+/*
+ * Like get_cycles - but where c0_count is not available we desperately
+ * use c0_random in an attempt to get at least a little bit of entropy.
+ */
+static inline unsigned long random_get_entropy(void)
+{
+	unsigned int c0_random;
+
+	if (can_use_mips_counter(read_c0_prid()))
+		return read_c0_count();
+
+	if (cpu_has_3kex)
+		c0_random = (read_c0_random() >> 8) & 0x3f;
+	else
+		c0_random = read_c0_random() & 0x3f;
+	return (random_get_entropy_fallback() << 6) | (0x3f - c0_random);
+}
+#define random_get_entropy random_get_entropy
+
+#endif /* __KERNEL__ */
+
+#endif /*  _ASM_TIMEX_H */
diff --git a/arch/mips/include/asm/tlb.h b/arch/mips/include/asm/tlb.h
new file mode 100644
index 000000000..90f3ad76d
--- /dev/null
+++ b/arch/mips/include/asm/tlb.h
@@ -0,0 +1,26 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_TLB_H
+#define __ASM_TLB_H
+
+#include <asm/cpu-features.h>
+#include <asm/mipsregs.h>
+
+#define _UNIQUE_ENTRYHI(base, idx)					\
+		(((base) + ((idx) << (PAGE_SHIFT + 1))) |		\
+		 (cpu_has_tlbinv ? MIPS_ENTRYHI_EHINV : 0))
+#define UNIQUE_ENTRYHI(idx)		_UNIQUE_ENTRYHI(CKSEG0, idx)
+#define UNIQUE_GUEST_ENTRYHI(idx)	_UNIQUE_ENTRYHI(CKSEG1, idx)
+
+static inline unsigned int num_wired_entries(void)
+{
+	unsigned int wired = read_c0_wired();
+
+	if (cpu_has_mips_r6)
+		wired &= MIPSR6_WIRED_WIRED;
+
+	return wired;
+}
+
+#include <asm-generic/tlb.h>
+
+#endif /* __ASM_TLB_H */
diff --git a/arch/mips/include/asm/tlbdebug.h b/arch/mips/include/asm/tlbdebug.h
new file mode 100644
index 000000000..3a25a8780
--- /dev/null
+++ b/arch/mips/include/asm/tlbdebug.h
@@ -0,0 +1,17 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2002 by Ralf Baechle
+ */
+#ifndef __ASM_TLBDEBUG_H
+#define __ASM_TLBDEBUG_H
+
+/*
+ * TLB debugging functions:
+ */
+extern void dump_tlb_regs(void);
+extern void dump_tlb_all(void);
+
+#endif /* __ASM_TLBDEBUG_H */
diff --git a/arch/mips/include/asm/tlbex.h b/arch/mips/include/asm/tlbex.h
new file mode 100644
index 000000000..6d97e23f3
--- /dev/null
+++ b/arch/mips/include/asm/tlbex.h
@@ -0,0 +1,36 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_TLBEX_H
+#define __ASM_TLBEX_H
+
+#include <asm/uasm.h>
+
+/*
+ * Write random or indexed TLB entry, and care about the hazards from
+ * the preceding mtc0 and for the following eret.
+ */
+enum tlb_write_entry {
+	tlb_random,
+	tlb_indexed
+};
+
+extern int pgd_reg;
+
+void build_get_pmde64(u32 **p, struct uasm_label **l, struct uasm_reloc **r,
+		      unsigned int tmp, unsigned int ptr);
+void build_get_pgde32(u32 **p, unsigned int tmp, unsigned int ptr);
+void build_get_ptep(u32 **p, unsigned int tmp, unsigned int ptr);
+void build_update_entries(u32 **p, unsigned int tmp, unsigned int ptep);
+void build_tlb_write_entry(u32 **p, struct uasm_label **l,
+			   struct uasm_reloc **r,
+			   enum tlb_write_entry wmode);
+
+extern void handle_tlbl(void);
+extern char handle_tlbl_end[];
+
+extern void handle_tlbs(void);
+extern char handle_tlbs_end[];
+
+extern void handle_tlbm(void);
+extern char handle_tlbm_end[];
+
+#endif /* __ASM_TLBEX_H */
diff --git a/arch/mips/include/asm/tlbflush.h b/arch/mips/include/asm/tlbflush.h
new file mode 100644
index 000000000..9789e7a32
--- /dev/null
+++ b/arch/mips/include/asm/tlbflush.h
@@ -0,0 +1,49 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_TLBFLUSH_H
+#define __ASM_TLBFLUSH_H
+
+#include <linux/mm.h>
+
+/*
+ * TLB flushing:
+ *
+ *  - flush_tlb_all() flushes all processes TLB entries
+ *  - flush_tlb_mm(mm) flushes the specified mm context TLB entries
+ *  - flush_tlb_page(vma, vmaddr) flushes one page
+ *  - flush_tlb_range(vma, start, end) flushes a range of pages
+ *  - flush_tlb_kernel_range(start, end) flushes a range of kernel pages
+ */
+extern void local_flush_tlb_all(void);
+extern void local_flush_tlb_range(struct vm_area_struct *vma,
+	unsigned long start, unsigned long end);
+extern void local_flush_tlb_kernel_range(unsigned long start,
+	unsigned long end);
+extern void local_flush_tlb_page(struct vm_area_struct *vma,
+	unsigned long page);
+extern void local_flush_tlb_one(unsigned long vaddr);
+
+#include <asm/mmu_context.h>
+
+#ifdef CONFIG_SMP
+
+extern void flush_tlb_all(void);
+extern void flush_tlb_mm(struct mm_struct *);
+extern void flush_tlb_range(struct vm_area_struct *vma, unsigned long,
+	unsigned long);
+extern void flush_tlb_kernel_range(unsigned long, unsigned long);
+extern void flush_tlb_page(struct vm_area_struct *, unsigned long);
+extern void flush_tlb_one(unsigned long vaddr);
+
+#else /* CONFIG_SMP */
+
+#define flush_tlb_all()			local_flush_tlb_all()
+#define flush_tlb_mm(mm)		drop_mmu_context(mm)
+#define flush_tlb_range(vma, vmaddr, end)	local_flush_tlb_range(vma, vmaddr, end)
+#define flush_tlb_kernel_range(vmaddr,end) \
+	local_flush_tlb_kernel_range(vmaddr, end)
+#define flush_tlb_page(vma, page)	local_flush_tlb_page(vma, page)
+#define flush_tlb_one(vaddr)		local_flush_tlb_one(vaddr)
+
+#endif /* CONFIG_SMP */
+
+#endif /* __ASM_TLBFLUSH_H */
diff --git a/arch/mips/include/asm/tlbmisc.h b/arch/mips/include/asm/tlbmisc.h
new file mode 100644
index 000000000..c1a540669
--- /dev/null
+++ b/arch/mips/include/asm/tlbmisc.h
@@ -0,0 +1,11 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_TLBMISC_H
+#define __ASM_TLBMISC_H
+
+/*
+ * - add_wired_entry() add a fixed TLB entry, and move wired register
+ */
+extern void add_wired_entry(unsigned long entrylo0, unsigned long entrylo1,
+	unsigned long entryhi, unsigned long pagemask);
+
+#endif /* __ASM_TLBMISC_H */
diff --git a/arch/mips/include/asm/topology.h b/arch/mips/include/asm/topology.h
new file mode 100644
index 000000000..0673d2d0f
--- /dev/null
+++ b/arch/mips/include/asm/topology.h
@@ -0,0 +1,21 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2007 by Ralf Baechle
+ */
+#ifndef __ASM_TOPOLOGY_H
+#define __ASM_TOPOLOGY_H
+
+#include <topology.h>
+#include <linux/smp.h>
+
+#ifdef CONFIG_SMP
+#define topology_physical_package_id(cpu)	(cpu_data[cpu].package)
+#define topology_core_id(cpu)			(cpu_core(&cpu_data[cpu]))
+#define topology_core_cpumask(cpu)		(&cpu_core_map[cpu])
+#define topology_sibling_cpumask(cpu)		(&cpu_sibling_map[cpu])
+#endif
+
+#endif /* __ASM_TOPOLOGY_H */
diff --git a/arch/mips/include/asm/traps.h b/arch/mips/include/asm/traps.h
new file mode 100644
index 000000000..15cde638b
--- /dev/null
+++ b/arch/mips/include/asm/traps.h
@@ -0,0 +1,42 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ *	Trap handling definitions.
+ *
+ *	Copyright (C) 2002, 2003  Maciej W. Rozycki
+ */
+#ifndef _ASM_TRAPS_H
+#define _ASM_TRAPS_H
+
+/*
+ * Possible status responses for a board_be_handler backend.
+ */
+#define MIPS_BE_DISCARD 0		/* return with no action */
+#define MIPS_BE_FIXUP	1		/* return to the fixup code */
+#define MIPS_BE_FATAL	2		/* treat as an unrecoverable error */
+
+extern void (*board_be_init)(void);
+void mips_set_be_handler(int (*handler)(struct pt_regs *reg, int is_fixup));
+
+extern void (*board_nmi_handler_setup)(void);
+extern void (*board_ejtag_handler_setup)(void);
+extern void (*board_bind_eic_interrupt)(int irq, int regset);
+extern void (*board_ebase_setup)(void);
+extern void (*board_cache_error_setup)(void);
+
+extern int register_nmi_notifier(struct notifier_block *nb);
+extern void reserve_exception_space(phys_addr_t addr, unsigned long size);
+extern char except_vec_nmi[];
+
+#define VECTORSPACING 0x100	/* for EI/VI mode */
+
+#define nmi_notifier(fn, pri)						\
+({									\
+	static struct notifier_block fn##_nb = {			\
+		.notifier_call = fn,					\
+		.priority = pri						\
+	};								\
+									\
+	register_nmi_notifier(&fn##_nb);				\
+})
+
+#endif /* _ASM_TRAPS_H */
diff --git a/arch/mips/include/asm/txx9/boards.h b/arch/mips/include/asm/txx9/boards.h
new file mode 100644
index 000000000..6897ca436
--- /dev/null
+++ b/arch/mips/include/asm/txx9/boards.h
@@ -0,0 +1,5 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifdef CONFIG_TOSHIBA_RBTX4927
+BOARD_VEC(rbtx4927_vec)
+BOARD_VEC(rbtx4937_vec)
+#endif
diff --git a/arch/mips/include/asm/txx9/dmac.h b/arch/mips/include/asm/txx9/dmac.h
new file mode 100644
index 000000000..b47ef5fe7
--- /dev/null
+++ b/arch/mips/include/asm/txx9/dmac.h
@@ -0,0 +1,48 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * TXx9 SoC DMA Controller
+ */
+
+#ifndef __ASM_TXX9_DMAC_H
+#define __ASM_TXX9_DMAC_H
+
+#include <linux/dmaengine.h>
+
+#define TXX9_DMA_MAX_NR_CHANNELS	4
+
+/**
+ * struct txx9dmac_platform_data - Controller configuration parameters
+ * @memcpy_chan: Channel used for DMA_MEMCPY
+ * @have_64bit_regs: DMAC have 64 bit registers
+ */
+struct txx9dmac_platform_data {
+	int	memcpy_chan;
+	bool	have_64bit_regs;
+};
+
+/**
+ * struct txx9dmac_chan_platform_data - Channel configuration parameters
+ * @dmac_dev: A platform device for DMAC
+ */
+struct txx9dmac_chan_platform_data {
+	struct platform_device *dmac_dev;
+};
+
+/**
+ * struct txx9dmac_slave - Controller-specific information about a slave
+ * @tx_reg: physical address of data register used for
+ *	memory-to-peripheral transfers
+ * @rx_reg: physical address of data register used for
+ *	peripheral-to-memory transfers
+ * @reg_width: peripheral register width
+ */
+struct txx9dmac_slave {
+	u64		tx_reg;
+	u64		rx_reg;
+	unsigned int	reg_width;
+};
+
+void txx9_dmac_init(int id, unsigned long baseaddr, int irq,
+		    const struct txx9dmac_platform_data *pdata);
+
+#endif /* __ASM_TXX9_DMAC_H */
diff --git a/arch/mips/include/asm/txx9/generic.h b/arch/mips/include/asm/txx9/generic.h
new file mode 100644
index 000000000..9a2c47bf3
--- /dev/null
+++ b/arch/mips/include/asm/txx9/generic.h
@@ -0,0 +1,98 @@
+/*
+ * linux/include/asm-mips/txx9/generic.h
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#ifndef __ASM_TXX9_GENERIC_H
+#define __ASM_TXX9_GENERIC_H
+
+#include <linux/init.h>
+#include <linux/ioport.h>	/* for struct resource */
+
+extern struct resource txx9_ce_res[];
+#define TXX9_CE(n)	(unsigned long)(txx9_ce_res[(n)].start)
+extern unsigned int txx9_pcode;
+extern char txx9_pcode_str[8];
+void txx9_reg_res_init(unsigned int pcode, unsigned long base,
+		       unsigned long size);
+
+extern unsigned int txx9_master_clock;
+extern unsigned int txx9_cpu_clock;
+extern unsigned int txx9_gbus_clock;
+#define TXX9_IMCLK	(txx9_gbus_clock / 2)
+
+extern int txx9_ccfg_toeon;
+struct uart_port;
+int early_serial_txx9_setup(struct uart_port *port);
+
+struct pci_dev;
+struct txx9_board_vec {
+	const char *system;
+	void (*prom_init)(void);
+	void (*mem_setup)(void);
+	void (*irq_setup)(void);
+	void (*time_init)(void);
+	void (*arch_init)(void);
+	void (*device_init)(void);
+#ifdef CONFIG_PCI
+	int (*pci_map_irq)(const struct pci_dev *dev, u8 slot, u8 pin);
+#endif
+};
+extern struct txx9_board_vec *txx9_board_vec;
+extern int (*txx9_irq_dispatch)(int pending);
+const char *prom_getenv(const char *name);
+void txx9_wdt_init(unsigned long base);
+void txx9_wdt_now(unsigned long base);
+void txx9_spi_init(int busid, unsigned long base, int irq);
+void txx9_ethaddr_init(unsigned int id, unsigned char *ethaddr);
+void txx9_sio_init(unsigned long baseaddr, int irq,
+		   unsigned int line, unsigned int sclk, int nocts);
+#ifdef CONFIG_EARLY_PRINTK
+extern void (*txx9_prom_putchar)(char c);
+void txx9_sio_putchar_init(unsigned long baseaddr);
+#else
+static inline void txx9_sio_putchar_init(unsigned long baseaddr)
+{
+}
+#endif
+
+struct physmap_flash_data;
+void txx9_physmap_flash_init(int no, unsigned long addr, unsigned long size,
+			     const struct physmap_flash_data *pdata);
+
+/* 8 bit version of __fls(): find first bit set (returns 0..7) */
+static inline unsigned int __fls8(unsigned char x)
+{
+	int r = 7;
+
+	if (!(x & 0xf0)) {
+		r -= 4;
+		x <<= 4;
+	}
+	if (!(x & 0xc0)) {
+		r -= 2;
+		x <<= 2;
+	}
+	if (!(x & 0x80))
+		r -= 1;
+	return r;
+}
+
+void txx9_iocled_init(unsigned long baseaddr,
+		      int basenum, unsigned int num, int lowactive,
+		      const char *color, char **deftriggers);
+
+/* 7SEG LED */
+void txx9_7segled_init(unsigned int num,
+		       void (*putc)(unsigned int pos, unsigned char val));
+int txx9_7segled_putc(unsigned int pos, char c);
+
+void __init txx9_aclc_init(unsigned long baseaddr, int irq,
+			   unsigned int dmac_id,
+			   unsigned int dma_chan_out,
+			   unsigned int dma_chan_in);
+void __init txx9_sramc_init(struct resource *r);
+
+#endif /* __ASM_TXX9_GENERIC_H */
diff --git a/arch/mips/include/asm/txx9/pci.h b/arch/mips/include/asm/txx9/pci.h
new file mode 100644
index 000000000..3d3252906
--- /dev/null
+++ b/arch/mips/include/asm/txx9/pci.h
@@ -0,0 +1,39 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#ifndef __ASM_TXX9_PCI_H
+#define __ASM_TXX9_PCI_H
+
+#include <linux/pci.h>
+
+extern struct pci_controller txx9_primary_pcic;
+struct pci_controller *
+txx9_alloc_pci_controller(struct pci_controller *pcic,
+			  unsigned long mem_base, unsigned long mem_size,
+			  unsigned long io_base, unsigned long io_size);
+
+int txx9_pci66_check(struct pci_controller *hose, int top_bus,
+			int current_bus);
+extern int txx9_pci_mem_high __initdata;
+
+extern int txx9_pci_option;
+#define TXX9_PCI_OPT_PICMG	0x0002
+#define TXX9_PCI_OPT_CLK_33	0x0008
+#define TXX9_PCI_OPT_CLK_66	0x0010
+#define TXX9_PCI_OPT_CLK_MASK	\
+	(TXX9_PCI_OPT_CLK_33 | TXX9_PCI_OPT_CLK_66)
+#define TXX9_PCI_OPT_CLK_AUTO	TXX9_PCI_OPT_CLK_MASK
+
+enum txx9_pci_err_action {
+	TXX9_PCI_ERR_REPORT,
+	TXX9_PCI_ERR_IGNORE,
+	TXX9_PCI_ERR_PANIC,
+};
+extern enum txx9_pci_err_action txx9_pci_err_action;
+
+extern char * (*txx9_board_pcibios_setup)(char *str);
+char *txx9_pcibios_setup(char *str);
+
+#endif /* __ASM_TXX9_PCI_H */
diff --git a/arch/mips/include/asm/txx9/rbtx4927.h b/arch/mips/include/asm/txx9/rbtx4927.h
new file mode 100644
index 000000000..4060ad26c
--- /dev/null
+++ b/arch/mips/include/asm/txx9/rbtx4927.h
@@ -0,0 +1,92 @@
+/*
+ * Author: MontaVista Software, Inc.
+ *	   source@mvista.com
+ *
+ * Copyright 2001-2002 MontaVista Software Inc.
+ *
+ *  This program is free software; you can redistribute it and/or modify it
+ *  under the terms of the GNU General Public License as published by the
+ *  Free Software Foundation; either version 2 of the License, or (at your
+ *  option) any later version.
+ *
+ *  THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ *  WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
+ *  IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ *  BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ *  OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ *  ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
+ *  TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
+ *  USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the GNU General Public License along
+ *  with this program; if not, write to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+#ifndef __ASM_TXX9_RBTX4927_H
+#define __ASM_TXX9_RBTX4927_H
+
+#include <asm/txx9/tx4927.h>
+
+#define RBTX4927_PCIMEM		0x08000000
+#define RBTX4927_PCIMEM_SIZE	0x08000000
+#define RBTX4927_PCIIO		0x16000000
+#define RBTX4927_PCIIO_SIZE	0x01000000
+
+#define RBTX4927_LED_ADDR	(IO_BASE + TXX9_CE(2) + 0x00001000)
+#define RBTX4927_IMASK_ADDR	(IO_BASE + TXX9_CE(2) + 0x00002000)
+#define RBTX4927_IMSTAT_ADDR	(IO_BASE + TXX9_CE(2) + 0x00002006)
+#define RBTX4927_SOFTINT_ADDR	(IO_BASE + TXX9_CE(2) + 0x00003000)
+#define RBTX4927_SOFTRESET_ADDR (IO_BASE + TXX9_CE(2) + 0x0000f000)
+#define RBTX4927_SOFTRESETLOCK_ADDR	(IO_BASE + TXX9_CE(2) + 0x0000f002)
+#define RBTX4927_PCIRESET_ADDR	(IO_BASE + TXX9_CE(2) + 0x0000f006)
+#define RBTX4927_BRAMRTC_BASE	(IO_BASE + TXX9_CE(2) + 0x00010000)
+#define RBTX4927_ETHER_BASE	(IO_BASE + TXX9_CE(2) + 0x00020000)
+
+/* Ethernet port address */
+#define RBTX4927_ETHER_ADDR	(RBTX4927_ETHER_BASE + 0x280)
+
+#define rbtx4927_imask_addr	((__u8 __iomem *)RBTX4927_IMASK_ADDR)
+#define rbtx4927_imstat_addr	((__u8 __iomem *)RBTX4927_IMSTAT_ADDR)
+#define rbtx4927_softint_addr	((__u8 __iomem *)RBTX4927_SOFTINT_ADDR)
+#define rbtx4927_softreset_addr ((__u8 __iomem *)RBTX4927_SOFTRESET_ADDR)
+#define rbtx4927_softresetlock_addr	\
+				((__u8 __iomem *)RBTX4927_SOFTRESETLOCK_ADDR)
+#define rbtx4927_pcireset_addr	((__u8 __iomem *)RBTX4927_PCIRESET_ADDR)
+
+/* bits for ISTAT/IMASK/IMSTAT */
+#define RBTX4927_INTB_PCID	0
+#define RBTX4927_INTB_PCIC	1
+#define RBTX4927_INTB_PCIB	2
+#define RBTX4927_INTB_PCIA	3
+#define RBTX4927_INTF_PCID	(1 << RBTX4927_INTB_PCID)
+#define RBTX4927_INTF_PCIC	(1 << RBTX4927_INTB_PCIC)
+#define RBTX4927_INTF_PCIB	(1 << RBTX4927_INTB_PCIB)
+#define RBTX4927_INTF_PCIA	(1 << RBTX4927_INTB_PCIA)
+
+#define RBTX4927_NR_IRQ_IOC	8	/* IOC */
+
+#define RBTX4927_IRQ_IOC	(TXX9_IRQ_BASE + TX4927_NUM_IR)
+#define RBTX4927_IRQ_IOC_PCID	(RBTX4927_IRQ_IOC + RBTX4927_INTB_PCID)
+#define RBTX4927_IRQ_IOC_PCIC	(RBTX4927_IRQ_IOC + RBTX4927_INTB_PCIC)
+#define RBTX4927_IRQ_IOC_PCIB	(RBTX4927_IRQ_IOC + RBTX4927_INTB_PCIB)
+#define RBTX4927_IRQ_IOC_PCIA	(RBTX4927_IRQ_IOC + RBTX4927_INTB_PCIA)
+
+#define RBTX4927_IRQ_IOCINT	(TXX9_IRQ_BASE + TX4927_IR_INT(1))
+
+#ifdef CONFIG_PCI
+#define RBTX4927_ISA_IO_OFFSET RBTX4927_PCIIO
+#else
+#define RBTX4927_ISA_IO_OFFSET 0
+#endif
+
+#define RBTX4927_RTL_8019_BASE (RBTX4927_ETHER_ADDR - mips_io_port_base)
+#define RBTX4927_RTL_8019_IRQ  (TXX9_IRQ_BASE + TX4927_IR_INT(3))
+
+void rbtx4927_prom_init(void);
+void rbtx4927_irq_setup(void);
+struct pci_dev;
+int rbtx4927_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin);
+
+#endif /* __ASM_TXX9_RBTX4927_H */
diff --git a/arch/mips/include/asm/txx9/smsc_fdc37m81x.h b/arch/mips/include/asm/txx9/smsc_fdc37m81x.h
new file mode 100644
index 000000000..926d08f18
--- /dev/null
+++ b/arch/mips/include/asm/txx9/smsc_fdc37m81x.h
@@ -0,0 +1,68 @@
+/*
+ * Interface for smsc fdc48m81x Super IO chip
+ *
+ * Author: MontaVista Software, Inc. source@mvista.com
+ *
+ * 2001-2003 (c) MontaVista Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ *
+ * Copyright (C) 2004 MontaVista Software Inc.
+ * Manish Lachwani, mlachwani@mvista.com
+ */
+
+#ifndef _SMSC_FDC37M81X_H_
+#define _SMSC_FDC37M81X_H_
+
+/* Common Registers */
+#define SMSC_FDC37M81X_CONFIG_INDEX  0x00
+#define SMSC_FDC37M81X_CONFIG_DATA   0x01
+#define SMSC_FDC37M81X_CONF	     0x02
+#define SMSC_FDC37M81X_INDEX	     0x03
+#define SMSC_FDC37M81X_DNUM	     0x07
+#define SMSC_FDC37M81X_DID	     0x20
+#define SMSC_FDC37M81X_DREV	     0x21
+#define SMSC_FDC37M81X_PCNT	     0x22
+#define SMSC_FDC37M81X_PMGT	     0x23
+#define SMSC_FDC37M81X_OSC	     0x24
+#define SMSC_FDC37M81X_CONFPA0	     0x26
+#define SMSC_FDC37M81X_CONFPA1	     0x27
+#define SMSC_FDC37M81X_TEST4	     0x2B
+#define SMSC_FDC37M81X_TEST5	     0x2C
+#define SMSC_FDC37M81X_TEST1	     0x2D
+#define SMSC_FDC37M81X_TEST2	     0x2E
+#define SMSC_FDC37M81X_TEST3	     0x2F
+
+/* Logical device numbers */
+#define SMSC_FDC37M81X_FDD	     0x00
+#define SMSC_FDC37M81X_PARALLEL	     0x03
+#define SMSC_FDC37M81X_SERIAL1	     0x04
+#define SMSC_FDC37M81X_SERIAL2	     0x05
+#define SMSC_FDC37M81X_KBD	     0x07
+#define SMSC_FDC37M81X_AUXIO	     0x08
+#define SMSC_FDC37M81X_NONE	     0xff
+
+/* Logical device Config Registers */
+#define SMSC_FDC37M81X_ACTIVE	     0x30
+#define SMSC_FDC37M81X_BASEADDR0     0x60
+#define SMSC_FDC37M81X_BASEADDR1     0x61
+#define SMSC_FDC37M81X_INT	     0x70
+#define SMSC_FDC37M81X_INT2	     0x72
+#define SMSC_FDC37M81X_LDCR_F0	     0xF0
+
+/* Chip Config Values */
+#define SMSC_FDC37M81X_CONFIG_ENTER  0x55
+#define SMSC_FDC37M81X_CONFIG_EXIT   0xaa
+#define SMSC_FDC37M81X_CHIP_ID	     0x4d
+
+unsigned long smsc_fdc37m81x_init(unsigned long port);
+
+void smsc_fdc37m81x_config_beg(void);
+
+void smsc_fdc37m81x_config_end(void);
+
+u8 smsc_fdc37m81x_config_get(u8 reg);
+void smsc_fdc37m81x_config_set(u8 reg, u8 val);
+
+#endif
diff --git a/arch/mips/include/asm/txx9/tx4927.h b/arch/mips/include/asm/txx9/tx4927.h
new file mode 100644
index 000000000..284eea752
--- /dev/null
+++ b/arch/mips/include/asm/txx9/tx4927.h
@@ -0,0 +1,273 @@
+/*
+ * Author: MontaVista Software, Inc.
+ *	   source@mvista.com
+ *
+ * Copyright 2001-2006 MontaVista Software Inc.
+ *
+ *  This program is free software; you can redistribute it and/or modify it
+ *  under the terms of the GNU General Public License as published by the
+ *  Free Software Foundation; either version 2 of the License, or (at your
+ *  option) any later version.
+ *
+ *  THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ *  WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
+ *  IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ *  BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ *  OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ *  ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
+ *  TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
+ *  USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the GNU General Public License along
+ *  with this program; if not, write to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+#ifndef __ASM_TXX9_TX4927_H
+#define __ASM_TXX9_TX4927_H
+
+#include <linux/types.h>
+#include <linux/io.h>
+#include <asm/txx9irq.h>
+#include <asm/txx9/tx4927pcic.h>
+
+#ifdef CONFIG_64BIT
+#define TX4927_REG_BASE 0xffffffffff1f0000UL
+#else
+#define TX4927_REG_BASE 0xff1f0000UL
+#endif
+#define TX4927_REG_SIZE 0x00010000
+
+#define TX4927_SDRAMC_REG	(TX4927_REG_BASE + 0x8000)
+#define TX4927_EBUSC_REG	(TX4927_REG_BASE + 0x9000)
+#define TX4927_DMA_REG		(TX4927_REG_BASE + 0xb000)
+#define TX4927_PCIC_REG		(TX4927_REG_BASE + 0xd000)
+#define TX4927_CCFG_REG		(TX4927_REG_BASE + 0xe000)
+#define TX4927_IRC_REG		(TX4927_REG_BASE + 0xf600)
+#define TX4927_NR_TMR	3
+#define TX4927_TMR_REG(ch)	(TX4927_REG_BASE + 0xf000 + (ch) * 0x100)
+#define TX4927_NR_SIO	2
+#define TX4927_SIO_REG(ch)	(TX4927_REG_BASE + 0xf300 + (ch) * 0x100)
+#define TX4927_PIO_REG		(TX4927_REG_BASE + 0xf500)
+#define TX4927_ACLC_REG		(TX4927_REG_BASE + 0xf700)
+
+#define TX4927_IR_ECCERR	0
+#define TX4927_IR_WTOERR	1
+#define TX4927_NUM_IR_INT	6
+#define TX4927_IR_INT(n)	(2 + (n))
+#define TX4927_NUM_IR_SIO	2
+#define TX4927_IR_SIO(n)	(8 + (n))
+#define TX4927_NUM_IR_DMA	4
+#define TX4927_IR_DMA(n)	(10 + (n))
+#define TX4927_IR_PIO		14
+#define TX4927_IR_PDMAC		15
+#define TX4927_IR_PCIC		16
+#define TX4927_NUM_IR_TMR	3
+#define TX4927_IR_TMR(n)	(17 + (n))
+#define TX4927_IR_PCIERR	22
+#define TX4927_IR_PCIPME	23
+#define TX4927_IR_ACLC		24
+#define TX4927_IR_ACLCPME	25
+#define TX4927_NUM_IR	32
+
+#define TX4927_IRC_INT	2	/* IP[2] in Status register */
+
+#define TX4927_NUM_PIO	16
+
+struct tx4927_sdramc_reg {
+	u64 cr[4];
+	u64 unused0[4];
+	u64 tr;
+	u64 unused1[2];
+	u64 cmd;
+};
+
+struct tx4927_ebusc_reg {
+	u64 cr[8];
+};
+
+struct tx4927_ccfg_reg {
+	u64 ccfg;
+	u64 crir;
+	u64 pcfg;
+	u64 toea;
+	u64 clkctr;
+	u64 unused0;
+	u64 garbc;
+	u64 unused1;
+	u64 unused2;
+	u64 ramp;
+};
+
+/*
+ * CCFG
+ */
+/* CCFG : Chip Configuration */
+#define TX4927_CCFG_WDRST	0x0000020000000000ULL
+#define TX4927_CCFG_WDREXEN	0x0000010000000000ULL
+#define TX4927_CCFG_BCFG_MASK	0x000000ff00000000ULL
+#define TX4927_CCFG_TINTDIS	0x01000000
+#define TX4927_CCFG_PCI66	0x00800000
+#define TX4927_CCFG_PCIMODE	0x00400000
+#define TX4927_CCFG_DIVMODE_MASK	0x000e0000
+#define TX4927_CCFG_DIVMODE_8	(0x0 << 17)
+#define TX4927_CCFG_DIVMODE_12	(0x1 << 17)
+#define TX4927_CCFG_DIVMODE_16	(0x2 << 17)
+#define TX4927_CCFG_DIVMODE_10	(0x3 << 17)
+#define TX4927_CCFG_DIVMODE_2	(0x4 << 17)
+#define TX4927_CCFG_DIVMODE_3	(0x5 << 17)
+#define TX4927_CCFG_DIVMODE_4	(0x6 << 17)
+#define TX4927_CCFG_DIVMODE_2_5 (0x7 << 17)
+#define TX4927_CCFG_BEOW	0x00010000
+#define TX4927_CCFG_WR	0x00008000
+#define TX4927_CCFG_TOE 0x00004000
+#define TX4927_CCFG_PCIARB	0x00002000
+#define TX4927_CCFG_PCIDIVMODE_MASK	0x00001800
+#define TX4927_CCFG_PCIDIVMODE_2_5	0x00000000
+#define TX4927_CCFG_PCIDIVMODE_3	0x00000800
+#define TX4927_CCFG_PCIDIVMODE_5	0x00001000
+#define TX4927_CCFG_PCIDIVMODE_6	0x00001800
+#define TX4927_CCFG_SYSSP_MASK	0x000000c0
+#define TX4927_CCFG_ENDIAN	0x00000004
+#define TX4927_CCFG_HALT	0x00000002
+#define TX4927_CCFG_ACEHOLD	0x00000001
+#define TX4927_CCFG_W1CBITS	(TX4927_CCFG_WDRST | TX4927_CCFG_BEOW)
+
+/* PCFG : Pin Configuration */
+#define TX4927_PCFG_SDCLKDLY_MASK	0x30000000
+#define TX4927_PCFG_SDCLKDLY(d) ((d)<<28)
+#define TX4927_PCFG_SYSCLKEN	0x08000000
+#define TX4927_PCFG_SDCLKEN_ALL 0x07800000
+#define TX4927_PCFG_SDCLKEN(ch) (0x00800000<<(ch))
+#define TX4927_PCFG_PCICLKEN_ALL	0x003f0000
+#define TX4927_PCFG_PCICLKEN(ch)	(0x00010000<<(ch))
+#define TX4927_PCFG_SEL2	0x00000200
+#define TX4927_PCFG_SEL1	0x00000100
+#define TX4927_PCFG_DMASEL_ALL	0x000000ff
+#define TX4927_PCFG_DMASEL0_MASK	0x00000003
+#define TX4927_PCFG_DMASEL1_MASK	0x0000000c
+#define TX4927_PCFG_DMASEL2_MASK	0x00000030
+#define TX4927_PCFG_DMASEL3_MASK	0x000000c0
+#define TX4927_PCFG_DMASEL0_DRQ0	0x00000000
+#define TX4927_PCFG_DMASEL0_SIO1	0x00000001
+#define TX4927_PCFG_DMASEL0_ACL0	0x00000002
+#define TX4927_PCFG_DMASEL0_ACL2	0x00000003
+#define TX4927_PCFG_DMASEL1_DRQ1	0x00000000
+#define TX4927_PCFG_DMASEL1_SIO1	0x00000004
+#define TX4927_PCFG_DMASEL1_ACL1	0x00000008
+#define TX4927_PCFG_DMASEL1_ACL3	0x0000000c
+#define TX4927_PCFG_DMASEL2_DRQ2	0x00000000	/* SEL2=0 */
+#define TX4927_PCFG_DMASEL2_SIO0	0x00000010	/* SEL2=0 */
+#define TX4927_PCFG_DMASEL2_ACL1	0x00000000	/* SEL2=1 */
+#define TX4927_PCFG_DMASEL2_ACL2	0x00000020	/* SEL2=1 */
+#define TX4927_PCFG_DMASEL2_ACL0	0x00000030	/* SEL2=1 */
+#define TX4927_PCFG_DMASEL3_DRQ3	0x00000000
+#define TX4927_PCFG_DMASEL3_SIO0	0x00000040
+#define TX4927_PCFG_DMASEL3_ACL3	0x00000080
+#define TX4927_PCFG_DMASEL3_ACL1	0x000000c0
+
+/* CLKCTR : Clock Control */
+#define TX4927_CLKCTR_ACLCKD	0x02000000
+#define TX4927_CLKCTR_PIOCKD	0x01000000
+#define TX4927_CLKCTR_DMACKD	0x00800000
+#define TX4927_CLKCTR_PCICKD	0x00400000
+#define TX4927_CLKCTR_TM0CKD	0x00100000
+#define TX4927_CLKCTR_TM1CKD	0x00080000
+#define TX4927_CLKCTR_TM2CKD	0x00040000
+#define TX4927_CLKCTR_SIO0CKD	0x00020000
+#define TX4927_CLKCTR_SIO1CKD	0x00010000
+#define TX4927_CLKCTR_ACLRST	0x00000200
+#define TX4927_CLKCTR_PIORST	0x00000100
+#define TX4927_CLKCTR_DMARST	0x00000080
+#define TX4927_CLKCTR_PCIRST	0x00000040
+#define TX4927_CLKCTR_TM0RST	0x00000010
+#define TX4927_CLKCTR_TM1RST	0x00000008
+#define TX4927_CLKCTR_TM2RST	0x00000004
+#define TX4927_CLKCTR_SIO0RST	0x00000002
+#define TX4927_CLKCTR_SIO1RST	0x00000001
+
+#define tx4927_sdramcptr \
+		((struct tx4927_sdramc_reg __iomem *)TX4927_SDRAMC_REG)
+#define tx4927_pcicptr \
+		((struct tx4927_pcic_reg __iomem *)TX4927_PCIC_REG)
+#define tx4927_ccfgptr \
+		((struct tx4927_ccfg_reg __iomem *)TX4927_CCFG_REG)
+#define tx4927_ebuscptr \
+		((struct tx4927_ebusc_reg __iomem *)TX4927_EBUSC_REG)
+#define tx4927_pioptr		((struct txx9_pio_reg __iomem *)TX4927_PIO_REG)
+
+#define TX4927_REV_PCODE()	\
+	((__u32)__raw_readq(&tx4927_ccfgptr->crir) >> 16)
+
+#define TX4927_SDRAMC_CR(ch)	__raw_readq(&tx4927_sdramcptr->cr[(ch)])
+#define TX4927_SDRAMC_BA(ch)	((TX4927_SDRAMC_CR(ch) >> 49) << 21)
+#define TX4927_SDRAMC_SIZE(ch)	\
+	((((TX4927_SDRAMC_CR(ch) >> 33) & 0x7fff) + 1) << 21)
+
+#define TX4927_EBUSC_CR(ch)	__raw_readq(&tx4927_ebuscptr->cr[(ch)])
+#define TX4927_EBUSC_BA(ch)	((TX4927_EBUSC_CR(ch) >> 48) << 20)
+#define TX4927_EBUSC_SIZE(ch)	\
+	(0x00100000 << ((unsigned long)(TX4927_EBUSC_CR(ch) >> 8) & 0xf))
+#define TX4927_EBUSC_WIDTH(ch)	\
+	(64 >> ((__u32)(TX4927_EBUSC_CR(ch) >> 20) & 0x3))
+
+/* utilities */
+static inline void txx9_clear64(__u64 __iomem *adr, __u64 bits)
+{
+#ifdef CONFIG_32BIT
+	unsigned long flags;
+	local_irq_save(flags);
+#endif
+	____raw_writeq(____raw_readq(adr) & ~bits, adr);
+#ifdef CONFIG_32BIT
+	local_irq_restore(flags);
+#endif
+}
+static inline void txx9_set64(__u64 __iomem *adr, __u64 bits)
+{
+#ifdef CONFIG_32BIT
+	unsigned long flags;
+	local_irq_save(flags);
+#endif
+	____raw_writeq(____raw_readq(adr) | bits, adr);
+#ifdef CONFIG_32BIT
+	local_irq_restore(flags);
+#endif
+}
+
+/* These functions are not interrupt safe. */
+static inline void tx4927_ccfg_clear(__u64 bits)
+{
+	____raw_writeq(____raw_readq(&tx4927_ccfgptr->ccfg)
+		       & ~(TX4927_CCFG_W1CBITS | bits),
+		       &tx4927_ccfgptr->ccfg);
+}
+static inline void tx4927_ccfg_set(__u64 bits)
+{
+	____raw_writeq((____raw_readq(&tx4927_ccfgptr->ccfg)
+			& ~TX4927_CCFG_W1CBITS) | bits,
+		       &tx4927_ccfgptr->ccfg);
+}
+static inline void tx4927_ccfg_change(__u64 change, __u64 new)
+{
+	____raw_writeq((____raw_readq(&tx4927_ccfgptr->ccfg)
+			& ~(TX4927_CCFG_W1CBITS | change)) |
+		       new,
+		       &tx4927_ccfgptr->ccfg);
+}
+
+unsigned int tx4927_get_mem_size(void);
+void tx4927_wdt_init(void);
+void tx4927_setup(void);
+void tx4927_time_init(unsigned int tmrnr);
+void tx4927_sio_init(unsigned int sclk, unsigned int cts_mask);
+int tx4927_report_pciclk(void);
+int tx4927_pciclk66_setup(void);
+void tx4927_setup_pcierr_irq(void);
+void tx4927_irq_init(void);
+void tx4927_mtd_init(int ch);
+void tx4927_dmac_init(int memcpy_chan);
+void tx4927_aclc_init(unsigned int dma_chan_out, unsigned int dma_chan_in);
+
+#endif /* __ASM_TXX9_TX4927_H */
diff --git a/arch/mips/include/asm/txx9/tx4927pcic.h b/arch/mips/include/asm/txx9/tx4927pcic.h
new file mode 100644
index 000000000..9eab2698c
--- /dev/null
+++ b/arch/mips/include/asm/txx9/tx4927pcic.h
@@ -0,0 +1,203 @@
+/*
+ * include/asm-mips/txx9/tx4927pcic.h
+ * TX4927 PCI controller definitions.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#ifndef __ASM_TXX9_TX4927PCIC_H
+#define __ASM_TXX9_TX4927PCIC_H
+
+#include <linux/pci.h>
+#include <linux/irqreturn.h>
+
+struct tx4927_pcic_reg {
+	u32 pciid;
+	u32 pcistatus;
+	u32 pciccrev;
+	u32 pcicfg1;
+	u32 p2gm0plbase;		/* +10 */
+	u32 p2gm0pubase;
+	u32 p2gm1plbase;
+	u32 p2gm1pubase;
+	u32 p2gm2pbase;		/* +20 */
+	u32 p2giopbase;
+	u32 unused0;
+	u32 pcisid;
+	u32 unused1;		/* +30 */
+	u32 pcicapptr;
+	u32 unused2;
+	u32 pcicfg2;
+	u32 g2ptocnt;		/* +40 */
+	u32 unused3[15];
+	u32 g2pstatus;		/* +80 */
+	u32 g2pmask;
+	u32 pcisstatus;
+	u32 pcimask;
+	u32 p2gcfg;		/* +90 */
+	u32 p2gstatus;
+	u32 p2gmask;
+	u32 p2gccmd;
+	u32 unused4[24];		/* +a0 */
+	u32 pbareqport;		/* +100 */
+	u32 pbacfg;
+	u32 pbastatus;
+	u32 pbamask;
+	u32 pbabm;		/* +110 */
+	u32 pbacreq;
+	u32 pbacgnt;
+	u32 pbacstate;
+	u64 g2pmgbase[3];		/* +120 */
+	u64 g2piogbase;
+	u32 g2pmmask[3];		/* +140 */
+	u32 g2piomask;
+	u64 g2pmpbase[3];		/* +150 */
+	u64 g2piopbase;
+	u32 pciccfg;		/* +170 */
+	u32 pcicstatus;
+	u32 pcicmask;
+	u32 unused5;
+	u64 p2gmgbase[3];		/* +180 */
+	u64 p2giogbase;
+	u32 g2pcfgadrs;		/* +1a0 */
+	u32 g2pcfgdata;
+	u32 unused6[8];
+	u32 g2pintack;
+	u32 g2pspc;
+	u32 unused7[12];		/* +1d0 */
+	u64 pdmca;		/* +200 */
+	u64 pdmga;
+	u64 pdmpa;
+	u64 pdmctr;
+	u64 pdmcfg;		/* +220 */
+	u64 pdmsts;
+};
+
+/* bits for PCICMD */
+/* see PCI_COMMAND_XXX in linux/pci_regs.h */
+
+/* bits for PCISTAT */
+/* see PCI_STATUS_XXX in linux/pci_regs.h */
+
+/* bits for IOBA/MBA */
+/* see PCI_BASE_ADDRESS_XXX in linux/pci_regs.h */
+
+/* bits for G2PSTATUS/G2PMASK */
+#define TX4927_PCIC_G2PSTATUS_ALL	0x00000003
+#define TX4927_PCIC_G2PSTATUS_TTOE	0x00000002
+#define TX4927_PCIC_G2PSTATUS_RTOE	0x00000001
+
+/* bits for PCIMASK (see also PCI_STATUS_XXX in linux/pci_regs.h */
+#define TX4927_PCIC_PCISTATUS_ALL	0x0000f900
+
+/* bits for PBACFG */
+#define TX4927_PCIC_PBACFG_FIXPA	0x00000008
+#define TX4927_PCIC_PBACFG_RPBA 0x00000004
+#define TX4927_PCIC_PBACFG_PBAEN	0x00000002
+#define TX4927_PCIC_PBACFG_BMCEN	0x00000001
+
+/* bits for PBASTATUS/PBAMASK */
+#define TX4927_PCIC_PBASTATUS_ALL	0x00000001
+#define TX4927_PCIC_PBASTATUS_BM	0x00000001
+
+/* bits for G2PMnGBASE */
+#define TX4927_PCIC_G2PMnGBASE_BSDIS	0x0000002000000000ULL
+#define TX4927_PCIC_G2PMnGBASE_ECHG	0x0000001000000000ULL
+
+/* bits for G2PIOGBASE */
+#define TX4927_PCIC_G2PIOGBASE_BSDIS	0x0000002000000000ULL
+#define TX4927_PCIC_G2PIOGBASE_ECHG	0x0000001000000000ULL
+
+/* bits for PCICSTATUS/PCICMASK */
+#define TX4927_PCIC_PCICSTATUS_ALL	0x000007b8
+#define TX4927_PCIC_PCICSTATUS_PME	0x00000400
+#define TX4927_PCIC_PCICSTATUS_TLB	0x00000200
+#define TX4927_PCIC_PCICSTATUS_NIB	0x00000100
+#define TX4927_PCIC_PCICSTATUS_ZIB	0x00000080
+#define TX4927_PCIC_PCICSTATUS_PERR	0x00000020
+#define TX4927_PCIC_PCICSTATUS_SERR	0x00000010
+#define TX4927_PCIC_PCICSTATUS_GBE	0x00000008
+#define TX4927_PCIC_PCICSTATUS_IWB	0x00000002
+#define TX4927_PCIC_PCICSTATUS_E2PDONE	0x00000001
+
+/* bits for PCICCFG */
+#define TX4927_PCIC_PCICCFG_GBWC_MASK	0x0fff0000
+#define TX4927_PCIC_PCICCFG_HRST	0x00000800
+#define TX4927_PCIC_PCICCFG_SRST	0x00000400
+#define TX4927_PCIC_PCICCFG_IRBER	0x00000200
+#define TX4927_PCIC_PCICCFG_G2PMEN(ch)	(0x00000100>>(ch))
+#define TX4927_PCIC_PCICCFG_G2PM0EN	0x00000100
+#define TX4927_PCIC_PCICCFG_G2PM1EN	0x00000080
+#define TX4927_PCIC_PCICCFG_G2PM2EN	0x00000040
+#define TX4927_PCIC_PCICCFG_G2PIOEN	0x00000020
+#define TX4927_PCIC_PCICCFG_TCAR	0x00000010
+#define TX4927_PCIC_PCICCFG_ICAEN	0x00000008
+
+/* bits for P2GMnGBASE */
+#define TX4927_PCIC_P2GMnGBASE_TMEMEN	0x0000004000000000ULL
+#define TX4927_PCIC_P2GMnGBASE_TBSDIS	0x0000002000000000ULL
+#define TX4927_PCIC_P2GMnGBASE_TECHG	0x0000001000000000ULL
+
+/* bits for P2GIOGBASE */
+#define TX4927_PCIC_P2GIOGBASE_TIOEN	0x0000004000000000ULL
+#define TX4927_PCIC_P2GIOGBASE_TBSDIS	0x0000002000000000ULL
+#define TX4927_PCIC_P2GIOGBASE_TECHG	0x0000001000000000ULL
+
+#define TX4927_PCIC_IDSEL_AD_TO_SLOT(ad)	((ad) - 11)
+#define TX4927_PCIC_MAX_DEVNU	TX4927_PCIC_IDSEL_AD_TO_SLOT(32)
+
+/* bits for PDMCFG */
+#define TX4927_PCIC_PDMCFG_RSTFIFO	0x00200000
+#define TX4927_PCIC_PDMCFG_EXFER	0x00100000
+#define TX4927_PCIC_PDMCFG_REQDLY_MASK	0x00003800
+#define TX4927_PCIC_PDMCFG_REQDLY_NONE	(0 << 11)
+#define TX4927_PCIC_PDMCFG_REQDLY_16	(1 << 11)
+#define TX4927_PCIC_PDMCFG_REQDLY_32	(2 << 11)
+#define TX4927_PCIC_PDMCFG_REQDLY_64	(3 << 11)
+#define TX4927_PCIC_PDMCFG_REQDLY_128	(4 << 11)
+#define TX4927_PCIC_PDMCFG_REQDLY_256	(5 << 11)
+#define TX4927_PCIC_PDMCFG_REQDLY_512	(6 << 11)
+#define TX4927_PCIC_PDMCFG_REQDLY_1024	(7 << 11)
+#define TX4927_PCIC_PDMCFG_ERRIE	0x00000400
+#define TX4927_PCIC_PDMCFG_NCCMPIE	0x00000200
+#define TX4927_PCIC_PDMCFG_NTCMPIE	0x00000100
+#define TX4927_PCIC_PDMCFG_CHNEN	0x00000080
+#define TX4927_PCIC_PDMCFG_XFRACT	0x00000040
+#define TX4927_PCIC_PDMCFG_BSWAP	0x00000020
+#define TX4927_PCIC_PDMCFG_XFRSIZE_MASK 0x0000000c
+#define TX4927_PCIC_PDMCFG_XFRSIZE_1DW	0x00000000
+#define TX4927_PCIC_PDMCFG_XFRSIZE_1QW	0x00000004
+#define TX4927_PCIC_PDMCFG_XFRSIZE_4QW	0x00000008
+#define TX4927_PCIC_PDMCFG_XFRDIRC	0x00000002
+#define TX4927_PCIC_PDMCFG_CHRST	0x00000001
+
+/* bits for PDMSTS */
+#define TX4927_PCIC_PDMSTS_REQCNT_MASK	0x3f000000
+#define TX4927_PCIC_PDMSTS_FIFOCNT_MASK 0x00f00000
+#define TX4927_PCIC_PDMSTS_FIFOWP_MASK	0x000c0000
+#define TX4927_PCIC_PDMSTS_FIFORP_MASK	0x00030000
+#define TX4927_PCIC_PDMSTS_ERRINT	0x00000800
+#define TX4927_PCIC_PDMSTS_DONEINT	0x00000400
+#define TX4927_PCIC_PDMSTS_CHNEN	0x00000200
+#define TX4927_PCIC_PDMSTS_XFRACT	0x00000100
+#define TX4927_PCIC_PDMSTS_ACCMP	0x00000080
+#define TX4927_PCIC_PDMSTS_NCCMP	0x00000040
+#define TX4927_PCIC_PDMSTS_NTCMP	0x00000020
+#define TX4927_PCIC_PDMSTS_CFGERR	0x00000008
+#define TX4927_PCIC_PDMSTS_PCIERR	0x00000004
+#define TX4927_PCIC_PDMSTS_CHNERR	0x00000002
+#define TX4927_PCIC_PDMSTS_DATAERR	0x00000001
+#define TX4927_PCIC_PDMSTS_ALL_CMP	0x000000e0
+#define TX4927_PCIC_PDMSTS_ALL_ERR	0x0000000f
+
+struct tx4927_pcic_reg __iomem *get_tx4927_pcicptr(
+	struct pci_controller *channel);
+void tx4927_pcic_setup(struct tx4927_pcic_reg __iomem *pcicptr,
+		       struct pci_controller *channel, int extarb);
+void tx4927_report_pcic_status(void);
+char *tx4927_pcibios_setup(char *str);
+void tx4927_dump_pcic_settings(void);
+irqreturn_t tx4927_pcierr_interrupt(int irq, void *dev_id);
+
+#endif /* __ASM_TXX9_TX4927PCIC_H */
diff --git a/arch/mips/include/asm/txx9/tx4938.h b/arch/mips/include/asm/txx9/tx4938.h
new file mode 100644
index 000000000..6ca767ee6
--- /dev/null
+++ b/arch/mips/include/asm/txx9/tx4938.h
@@ -0,0 +1,312 @@
+/*
+ * Definitions for TX4937/TX4938
+ * Copyright (C) 2000-2001 Toshiba Corporation
+ *
+ * 2003-2005 (c) MontaVista Software, Inc. This file is licensed under the
+ * terms of the GNU General Public License version 2. This program is
+ * licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ *
+ * Support for TX4938 in 2.6 - Manish Lachwani (mlachwani@mvista.com)
+ */
+#ifndef __ASM_TXX9_TX4938_H
+#define __ASM_TXX9_TX4938_H
+
+/* some controllers are compatible with 4927 */
+#include <asm/txx9/tx4927.h>
+
+#ifdef CONFIG_64BIT
+#define TX4938_REG_BASE 0xffffffffff1f0000UL /* == TX4937_REG_BASE */
+#else
+#define TX4938_REG_BASE 0xff1f0000UL /* == TX4937_REG_BASE */
+#endif
+#define TX4938_REG_SIZE 0x00010000 /* == TX4937_REG_SIZE */
+
+/* NDFMC, SRAMC, PCIC1, SPIC: TX4938 only */
+#define TX4938_NDFMC_REG	(TX4938_REG_BASE + 0x5000)
+#define TX4938_SRAMC_REG	(TX4938_REG_BASE + 0x6000)
+#define TX4938_PCIC1_REG	(TX4938_REG_BASE + 0x7000)
+#define TX4938_SDRAMC_REG	(TX4938_REG_BASE + 0x8000)
+#define TX4938_EBUSC_REG	(TX4938_REG_BASE + 0x9000)
+#define TX4938_DMA_REG(ch)	(TX4938_REG_BASE + 0xb000 + (ch) * 0x800)
+#define TX4938_PCIC_REG		(TX4938_REG_BASE + 0xd000)
+#define TX4938_CCFG_REG		(TX4938_REG_BASE + 0xe000)
+#define TX4938_NR_TMR	3
+#define TX4938_TMR_REG(ch)	((TX4938_REG_BASE + 0xf000) + (ch) * 0x100)
+#define TX4938_NR_SIO	2
+#define TX4938_SIO_REG(ch)	((TX4938_REG_BASE + 0xf300) + (ch) * 0x100)
+#define TX4938_PIO_REG		(TX4938_REG_BASE + 0xf500)
+#define TX4938_IRC_REG		(TX4938_REG_BASE + 0xf600)
+#define TX4938_ACLC_REG		(TX4938_REG_BASE + 0xf700)
+#define TX4938_SPI_REG		(TX4938_REG_BASE + 0xf800)
+
+struct tx4938_sramc_reg {
+	u64 cr;
+};
+
+struct tx4938_ccfg_reg {
+	u64 ccfg;
+	u64 crir;
+	u64 pcfg;
+	u64 toea;
+	u64 clkctr;
+	u64 unused0;
+	u64 garbc;
+	u64 unused1;
+	u64 unused2;
+	u64 ramp;
+	u64 unused3;
+	u64 jmpadr;
+};
+
+/*
+ * IRC
+ */
+
+#define TX4938_IR_ECCERR	0
+#define TX4938_IR_WTOERR	1
+#define TX4938_NUM_IR_INT	6
+#define TX4938_IR_INT(n)	(2 + (n))
+#define TX4938_NUM_IR_SIO	2
+#define TX4938_IR_SIO(n)	(8 + (n))
+#define TX4938_NUM_IR_DMA	4
+#define TX4938_IR_DMA(ch, n)	((ch ? 27 : 10) + (n)) /* 10-13, 27-30 */
+#define TX4938_IR_PIO	14
+#define TX4938_IR_PDMAC 15
+#define TX4938_IR_PCIC	16
+#define TX4938_NUM_IR_TMR	3
+#define TX4938_IR_TMR(n)	(17 + (n))
+#define TX4938_IR_NDFMC 21
+#define TX4938_IR_PCIERR	22
+#define TX4938_IR_PCIPME	23
+#define TX4938_IR_ACLC	24
+#define TX4938_IR_ACLCPME	25
+#define TX4938_IR_PCIC1 26
+#define TX4938_IR_SPI	31
+#define TX4938_NUM_IR	32
+/* multiplex */
+#define TX4938_IR_ETH0	TX4938_IR_INT(4)
+#define TX4938_IR_ETH1	TX4938_IR_INT(3)
+
+#define TX4938_IRC_INT	2	/* IP[2] in Status register */
+
+#define TX4938_NUM_PIO	16
+
+/*
+ * CCFG
+ */
+/* CCFG : Chip Configuration */
+#define TX4938_CCFG_WDRST	0x0000020000000000ULL
+#define TX4938_CCFG_WDREXEN	0x0000010000000000ULL
+#define TX4938_CCFG_BCFG_MASK	0x000000ff00000000ULL
+#define TX4938_CCFG_TINTDIS	0x01000000
+#define TX4938_CCFG_PCI66	0x00800000
+#define TX4938_CCFG_PCIMODE	0x00400000
+#define TX4938_CCFG_PCI1_66	0x00200000
+#define TX4938_CCFG_DIVMODE_MASK	0x001e0000
+#define TX4938_CCFG_DIVMODE_2	(0x4 << 17)
+#define TX4938_CCFG_DIVMODE_2_5 (0xf << 17)
+#define TX4938_CCFG_DIVMODE_3	(0x5 << 17)
+#define TX4938_CCFG_DIVMODE_4	(0x6 << 17)
+#define TX4938_CCFG_DIVMODE_4_5 (0xd << 17)
+#define TX4938_CCFG_DIVMODE_8	(0x0 << 17)
+#define TX4938_CCFG_DIVMODE_10	(0xb << 17)
+#define TX4938_CCFG_DIVMODE_12	(0x1 << 17)
+#define TX4938_CCFG_DIVMODE_16	(0x2 << 17)
+#define TX4938_CCFG_DIVMODE_18	(0x9 << 17)
+#define TX4938_CCFG_BEOW	0x00010000
+#define TX4938_CCFG_WR	0x00008000
+#define TX4938_CCFG_TOE 0x00004000
+#define TX4938_CCFG_PCIARB	0x00002000
+#define TX4938_CCFG_PCIDIVMODE_MASK	0x00001c00
+#define TX4938_CCFG_PCIDIVMODE_4	(0x1 << 10)
+#define TX4938_CCFG_PCIDIVMODE_4_5	(0x3 << 10)
+#define TX4938_CCFG_PCIDIVMODE_5	(0x5 << 10)
+#define TX4938_CCFG_PCIDIVMODE_5_5	(0x7 << 10)
+#define TX4938_CCFG_PCIDIVMODE_8	(0x0 << 10)
+#define TX4938_CCFG_PCIDIVMODE_9	(0x2 << 10)
+#define TX4938_CCFG_PCIDIVMODE_10	(0x4 << 10)
+#define TX4938_CCFG_PCIDIVMODE_11	(0x6 << 10)
+#define TX4938_CCFG_PCI1DMD	0x00000100
+#define TX4938_CCFG_SYSSP_MASK	0x000000c0
+#define TX4938_CCFG_ENDIAN	0x00000004
+#define TX4938_CCFG_HALT	0x00000002
+#define TX4938_CCFG_ACEHOLD	0x00000001
+
+/* PCFG : Pin Configuration */
+#define TX4938_PCFG_ETH0_SEL	0x8000000000000000ULL
+#define TX4938_PCFG_ETH1_SEL	0x4000000000000000ULL
+#define TX4938_PCFG_ATA_SEL	0x2000000000000000ULL
+#define TX4938_PCFG_ISA_SEL	0x1000000000000000ULL
+#define TX4938_PCFG_SPI_SEL	0x0800000000000000ULL
+#define TX4938_PCFG_NDF_SEL	0x0400000000000000ULL
+#define TX4938_PCFG_SDCLKDLY_MASK	0x30000000
+#define TX4938_PCFG_SDCLKDLY(d) ((d)<<28)
+#define TX4938_PCFG_SYSCLKEN	0x08000000
+#define TX4938_PCFG_SDCLKEN_ALL 0x07800000
+#define TX4938_PCFG_SDCLKEN(ch) (0x00800000<<(ch))
+#define TX4938_PCFG_PCICLKEN_ALL	0x003f0000
+#define TX4938_PCFG_PCICLKEN(ch)	(0x00010000<<(ch))
+#define TX4938_PCFG_SEL2	0x00000200
+#define TX4938_PCFG_SEL1	0x00000100
+#define TX4938_PCFG_DMASEL_ALL	0x0000000f
+#define TX4938_PCFG_DMASEL0_DRQ0	0x00000000
+#define TX4938_PCFG_DMASEL0_SIO1	0x00000001
+#define TX4938_PCFG_DMASEL1_DRQ1	0x00000000
+#define TX4938_PCFG_DMASEL1_SIO1	0x00000002
+#define TX4938_PCFG_DMASEL2_DRQ2	0x00000000
+#define TX4938_PCFG_DMASEL2_SIO0	0x00000004
+#define TX4938_PCFG_DMASEL3_DRQ3	0x00000000
+#define TX4938_PCFG_DMASEL3_SIO0	0x00000008
+
+/* CLKCTR : Clock Control */
+#define TX4938_CLKCTR_NDFCKD	0x0001000000000000ULL
+#define TX4938_CLKCTR_NDFRST	0x0000000100000000ULL
+#define TX4938_CLKCTR_ETH1CKD	0x80000000
+#define TX4938_CLKCTR_ETH0CKD	0x40000000
+#define TX4938_CLKCTR_SPICKD	0x20000000
+#define TX4938_CLKCTR_SRAMCKD	0x10000000
+#define TX4938_CLKCTR_PCIC1CKD	0x08000000
+#define TX4938_CLKCTR_DMA1CKD	0x04000000
+#define TX4938_CLKCTR_ACLCKD	0x02000000
+#define TX4938_CLKCTR_PIOCKD	0x01000000
+#define TX4938_CLKCTR_DMACKD	0x00800000
+#define TX4938_CLKCTR_PCICKD	0x00400000
+#define TX4938_CLKCTR_TM0CKD	0x00100000
+#define TX4938_CLKCTR_TM1CKD	0x00080000
+#define TX4938_CLKCTR_TM2CKD	0x00040000
+#define TX4938_CLKCTR_SIO0CKD	0x00020000
+#define TX4938_CLKCTR_SIO1CKD	0x00010000
+#define TX4938_CLKCTR_ETH1RST	0x00008000
+#define TX4938_CLKCTR_ETH0RST	0x00004000
+#define TX4938_CLKCTR_SPIRST	0x00002000
+#define TX4938_CLKCTR_SRAMRST	0x00001000
+#define TX4938_CLKCTR_PCIC1RST	0x00000800
+#define TX4938_CLKCTR_DMA1RST	0x00000400
+#define TX4938_CLKCTR_ACLRST	0x00000200
+#define TX4938_CLKCTR_PIORST	0x00000100
+#define TX4938_CLKCTR_DMARST	0x00000080
+#define TX4938_CLKCTR_PCIRST	0x00000040
+#define TX4938_CLKCTR_TM0RST	0x00000010
+#define TX4938_CLKCTR_TM1RST	0x00000008
+#define TX4938_CLKCTR_TM2RST	0x00000004
+#define TX4938_CLKCTR_SIO0RST	0x00000002
+#define TX4938_CLKCTR_SIO1RST	0x00000001
+
+/*
+ * DMA
+ */
+/* bits for MCR */
+#define TX4938_DMA_MCR_EIS(ch)	(0x10000000<<(ch))
+#define TX4938_DMA_MCR_DIS(ch)	(0x01000000<<(ch))
+#define TX4938_DMA_MCR_RSFIF	0x00000080
+#define TX4938_DMA_MCR_FIFUM(ch)	(0x00000008<<(ch))
+#define TX4938_DMA_MCR_RPRT	0x00000002
+#define TX4938_DMA_MCR_MSTEN	0x00000001
+
+/* bits for CCRn */
+#define TX4938_DMA_CCR_IMMCHN	0x20000000
+#define TX4938_DMA_CCR_USEXFSZ	0x10000000
+#define TX4938_DMA_CCR_LE	0x08000000
+#define TX4938_DMA_CCR_DBINH	0x04000000
+#define TX4938_DMA_CCR_SBINH	0x02000000
+#define TX4938_DMA_CCR_CHRST	0x01000000
+#define TX4938_DMA_CCR_RVBYTE	0x00800000
+#define TX4938_DMA_CCR_ACKPOL	0x00400000
+#define TX4938_DMA_CCR_REQPL	0x00200000
+#define TX4938_DMA_CCR_EGREQ	0x00100000
+#define TX4938_DMA_CCR_CHDN	0x00080000
+#define TX4938_DMA_CCR_DNCTL	0x00060000
+#define TX4938_DMA_CCR_EXTRQ	0x00010000
+#define TX4938_DMA_CCR_INTRQD	0x0000e000
+#define TX4938_DMA_CCR_INTENE	0x00001000
+#define TX4938_DMA_CCR_INTENC	0x00000800
+#define TX4938_DMA_CCR_INTENT	0x00000400
+#define TX4938_DMA_CCR_CHNEN	0x00000200
+#define TX4938_DMA_CCR_XFACT	0x00000100
+#define TX4938_DMA_CCR_SMPCHN	0x00000020
+#define TX4938_DMA_CCR_XFSZ(order)	(((order) << 2) & 0x0000001c)
+#define TX4938_DMA_CCR_XFSZ_1W	TX4938_DMA_CCR_XFSZ(2)
+#define TX4938_DMA_CCR_XFSZ_2W	TX4938_DMA_CCR_XFSZ(3)
+#define TX4938_DMA_CCR_XFSZ_4W	TX4938_DMA_CCR_XFSZ(4)
+#define TX4938_DMA_CCR_XFSZ_8W	TX4938_DMA_CCR_XFSZ(5)
+#define TX4938_DMA_CCR_XFSZ_16W TX4938_DMA_CCR_XFSZ(6)
+#define TX4938_DMA_CCR_XFSZ_32W TX4938_DMA_CCR_XFSZ(7)
+#define TX4938_DMA_CCR_MEMIO	0x00000002
+#define TX4938_DMA_CCR_SNGAD	0x00000001
+
+/* bits for CSRn */
+#define TX4938_DMA_CSR_CHNEN	0x00000400
+#define TX4938_DMA_CSR_STLXFER	0x00000200
+#define TX4938_DMA_CSR_CHNACT	0x00000100
+#define TX4938_DMA_CSR_ABCHC	0x00000080
+#define TX4938_DMA_CSR_NCHNC	0x00000040
+#define TX4938_DMA_CSR_NTRNFC	0x00000020
+#define TX4938_DMA_CSR_EXTDN	0x00000010
+#define TX4938_DMA_CSR_CFERR	0x00000008
+#define TX4938_DMA_CSR_CHERR	0x00000004
+#define TX4938_DMA_CSR_DESERR	0x00000002
+#define TX4938_DMA_CSR_SORERR	0x00000001
+
+#define tx4938_sdramcptr	tx4927_sdramcptr
+#define tx4938_ebuscptr		tx4927_ebuscptr
+#define tx4938_pcicptr		tx4927_pcicptr
+#define tx4938_pcic1ptr \
+		((struct tx4927_pcic_reg __iomem *)TX4938_PCIC1_REG)
+#define tx4938_ccfgptr \
+		((struct tx4938_ccfg_reg __iomem *)TX4938_CCFG_REG)
+#define tx4938_pioptr		((struct txx9_pio_reg __iomem *)TX4938_PIO_REG)
+#define tx4938_sramcptr \
+		((struct tx4938_sramc_reg __iomem *)TX4938_SRAMC_REG)
+
+
+#define TX4938_REV_PCODE()	\
+	((__u32)__raw_readq(&tx4938_ccfgptr->crir) >> 16)
+
+#define tx4938_ccfg_clear(bits) tx4927_ccfg_clear(bits)
+#define tx4938_ccfg_set(bits)	tx4927_ccfg_set(bits)
+#define tx4938_ccfg_change(change, new) tx4927_ccfg_change(change, new)
+
+#define TX4938_SDRAMC_CR(ch)	TX4927_SDRAMC_CR(ch)
+#define TX4938_SDRAMC_BA(ch)	TX4927_SDRAMC_BA(ch)
+#define TX4938_SDRAMC_SIZE(ch)	TX4927_SDRAMC_SIZE(ch)
+
+#define TX4938_EBUSC_CR(ch)	TX4927_EBUSC_CR(ch)
+#define TX4938_EBUSC_BA(ch)	TX4927_EBUSC_BA(ch)
+#define TX4938_EBUSC_SIZE(ch)	TX4927_EBUSC_SIZE(ch)
+#define TX4938_EBUSC_WIDTH(ch)	TX4927_EBUSC_WIDTH(ch)
+
+#define tx4938_get_mem_size() tx4927_get_mem_size()
+void tx4938_wdt_init(void);
+void tx4938_setup(void);
+void tx4938_time_init(unsigned int tmrnr);
+void tx4938_sio_init(unsigned int sclk, unsigned int cts_mask);
+void tx4938_spi_init(int busid);
+void tx4938_ethaddr_init(unsigned char *addr0, unsigned char *addr1);
+int tx4938_report_pciclk(void);
+void tx4938_report_pci1clk(void);
+int tx4938_pciclk66_setup(void);
+struct pci_dev;
+int tx4938_pcic1_map_irq(const struct pci_dev *dev, u8 slot);
+void tx4938_setup_pcierr_irq(void);
+void tx4938_irq_init(void);
+void tx4938_mtd_init(int ch);
+void tx4938_ndfmc_init(unsigned int hold, unsigned int spw);
+
+struct tx4938ide_platform_info {
+	/*
+	 * I/O port shift, for platforms with ports that are
+	 * constantly spaced and need larger than the 1-byte
+	 * spacing used by ata_std_ports().
+	 */
+	unsigned int ioport_shift;
+	unsigned int gbus_clock;	/*  0 means no PIO mode tuning. */
+	unsigned int ebus_ch;
+};
+
+void tx4938_ata_init(unsigned int irq, unsigned int shift, int tune);
+void tx4938_dmac_init(int memcpy_chan0, int memcpy_chan1);
+void tx4938_aclc_init(void);
+void tx4938_sramc_init(void);
+
+#endif
diff --git a/arch/mips/include/asm/txx9irq.h b/arch/mips/include/asm/txx9irq.h
new file mode 100644
index 000000000..3875243bb
--- /dev/null
+++ b/arch/mips/include/asm/txx9irq.h
@@ -0,0 +1,30 @@
+/*
+ * include/asm-mips/txx9irq.h
+ * TX39/TX49 interrupt controller definitions.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#ifndef __ASM_TXX9IRQ_H
+#define __ASM_TXX9IRQ_H
+
+#include <irq.h>
+
+#ifdef CONFIG_IRQ_MIPS_CPU
+#define TXX9_IRQ_BASE	(MIPS_CPU_IRQ_BASE + 8)
+#else
+#ifdef CONFIG_I8259
+#define TXX9_IRQ_BASE	(I8259A_IRQ_BASE + 16)
+#else
+#define TXX9_IRQ_BASE	0
+#endif
+#endif
+
+#define TXx9_MAX_IR 32
+
+void txx9_irq_init(unsigned long baseaddr);
+int txx9_irq(void);
+int txx9_irq_set_pri(int irc_irq, int new_pri);
+
+#endif /* __ASM_TXX9IRQ_H */
diff --git a/arch/mips/include/asm/txx9pio.h b/arch/mips/include/asm/txx9pio.h
new file mode 100644
index 000000000..3d6fa9f8d
--- /dev/null
+++ b/arch/mips/include/asm/txx9pio.h
@@ -0,0 +1,29 @@
+/*
+ * include/asm-mips/txx9pio.h
+ * TX39/TX49 PIO controller definitions.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#ifndef __ASM_TXX9PIO_H
+#define __ASM_TXX9PIO_H
+
+#include <linux/types.h>
+
+struct txx9_pio_reg {
+	__u32 dout;
+	__u32 din;
+	__u32 dir;
+	__u32 od;
+	__u32 flag[2];
+	__u32 pol;
+	__u32 intc;
+	__u32 maskcpu;
+	__u32 maskext;
+};
+
+int txx9_gpio_init(unsigned long baseaddr,
+		   unsigned int base, unsigned int num);
+
+#endif /* __ASM_TXX9PIO_H */
diff --git a/arch/mips/include/asm/txx9tmr.h b/arch/mips/include/asm/txx9tmr.h
new file mode 100644
index 000000000..a051b4113
--- /dev/null
+++ b/arch/mips/include/asm/txx9tmr.h
@@ -0,0 +1,63 @@
+/*
+ * include/asm-mips/txx9tmr.h
+ * TX39/TX49 timer controller definitions.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#ifndef __ASM_TXX9TMR_H
+#define __ASM_TXX9TMR_H
+
+#include <linux/types.h>
+
+struct txx9_tmr_reg {
+	u32 tcr;
+	u32 tisr;
+	u32 cpra;
+	u32 cprb;
+	u32 itmr;
+	u32 unused0[3];
+	u32 ccdr;
+	u32 unused1[3];
+	u32 pgmr;
+	u32 unused2[3];
+	u32 wtmr;
+	u32 unused3[43];
+	u32 trr;
+};
+
+/* TMTCR : Timer Control */
+#define TXx9_TMTCR_TCE		0x00000080
+#define TXx9_TMTCR_CCDE		0x00000040
+#define TXx9_TMTCR_CRE		0x00000020
+#define TXx9_TMTCR_ECES		0x00000008
+#define TXx9_TMTCR_CCS		0x00000004
+#define TXx9_TMTCR_TMODE_MASK	0x00000003
+#define TXx9_TMTCR_TMODE_ITVL	0x00000000
+#define TXx9_TMTCR_TMODE_PGEN	0x00000001
+#define TXx9_TMTCR_TMODE_WDOG	0x00000002
+
+/* TMTISR : Timer Int. Status */
+#define TXx9_TMTISR_TPIBS	0x00000004
+#define TXx9_TMTISR_TPIAS	0x00000002
+#define TXx9_TMTISR_TIIS	0x00000001
+
+/* TMITMR : Interval Timer Mode */
+#define TXx9_TMITMR_TIIE	0x00008000
+#define TXx9_TMITMR_TZCE	0x00000001
+
+/* TMWTMR : Watchdog Timer Mode */
+#define TXx9_TMWTMR_TWIE	0x00008000
+#define TXx9_TMWTMR_WDIS	0x00000080
+#define TXx9_TMWTMR_TWC		0x00000001
+
+void txx9_clocksource_init(unsigned long baseaddr,
+			   unsigned int imbusclk);
+void txx9_clockevent_init(unsigned long baseaddr, int irq,
+			  unsigned int imbusclk);
+void txx9_tmr_init(unsigned long baseaddr);
+
+#define TXX9_TIMER_BITS 32
+
+#endif /* __ASM_TXX9TMR_H */
diff --git a/arch/mips/include/asm/types.h b/arch/mips/include/asm/types.h
new file mode 100644
index 000000000..638ef88e2
--- /dev/null
+++ b/arch/mips/include/asm/types.h
@@ -0,0 +1,16 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994, 1995, 1996, 1999 by Ralf Baechle
+ * Copyright (C) 2008 Wind River Systems,
+ *   written by Ralf Baechle
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_TYPES_H
+#define _ASM_TYPES_H
+
+#include <asm-generic/int-ll64.h>
+
+#endif /* _ASM_TYPES_H */
diff --git a/arch/mips/include/asm/uaccess.h b/arch/mips/include/asm/uaccess.h
new file mode 100644
index 000000000..c0cede273
--- /dev/null
+++ b/arch/mips/include/asm/uaccess.h
@@ -0,0 +1,564 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1996, 1997, 1998, 1999, 2000, 03, 04 by Ralf Baechle
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ * Copyright (C) 2007  Maciej W. Rozycki
+ * Copyright (C) 2014, Imagination Technologies Ltd.
+ */
+#ifndef _ASM_UACCESS_H
+#define _ASM_UACCESS_H
+
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <asm/asm-eva.h>
+#include <asm/extable.h>
+
+#ifdef CONFIG_32BIT
+
+#define __UA_LIMIT 0x80000000UL
+#define TASK_SIZE_MAX	KSEG0
+
+#define __UA_ADDR	".word"
+#define __UA_LA		"la"
+#define __UA_ADDU	"addu"
+#define __UA_t0		"$8"
+#define __UA_t1		"$9"
+
+#endif /* CONFIG_32BIT */
+
+#ifdef CONFIG_64BIT
+
+extern u64 __ua_limit;
+
+#define __UA_LIMIT	__ua_limit
+#define TASK_SIZE_MAX	XKSSEG
+
+#define __UA_ADDR	".dword"
+#define __UA_LA		"dla"
+#define __UA_ADDU	"daddu"
+#define __UA_t0		"$12"
+#define __UA_t1		"$13"
+
+#endif /* CONFIG_64BIT */
+
+#include <asm-generic/access_ok.h>
+
+/*
+ * put_user: - Write a simple value into user space.
+ * @x:	 Value to copy to user space.
+ * @ptr: Destination address, in user space.
+ *
+ * Context: User context only. This function may sleep if pagefaults are
+ *          enabled.
+ *
+ * This macro copies a single simple value from kernel space to user
+ * space.  It supports simple types like char and int, but not larger
+ * data types like structures or arrays.
+ *
+ * @ptr must have pointer-to-simple-variable type, and @x must be assignable
+ * to the result of dereferencing @ptr.
+ *
+ * Returns zero on success, or -EFAULT on error.
+ */
+#define put_user(x, ptr)						\
+({									\
+	__typeof__(*(ptr)) __user *__p = (ptr);				\
+									\
+	might_fault();							\
+	access_ok(__p, sizeof(*__p)) ? __put_user((x), __p) : -EFAULT;	\
+})
+
+/*
+ * get_user: - Get a simple variable from user space.
+ * @x:	 Variable to store result.
+ * @ptr: Source address, in user space.
+ *
+ * Context: User context only. This function may sleep if pagefaults are
+ *          enabled.
+ *
+ * This macro copies a single simple variable from user space to kernel
+ * space.  It supports simple types like char and int, but not larger
+ * data types like structures or arrays.
+ *
+ * @ptr must have pointer-to-simple-variable type, and the result of
+ * dereferencing @ptr must be assignable to @x without a cast.
+ *
+ * Returns zero on success, or -EFAULT on error.
+ * On error, the variable @x is set to zero.
+ */
+#define get_user(x, ptr)						\
+({									\
+	const __typeof__(*(ptr)) __user *__p = (ptr);			\
+									\
+	might_fault();							\
+	access_ok(__p, sizeof(*__p)) ? __get_user((x), __p) :		\
+				       ((x) = 0, -EFAULT);		\
+})
+
+/*
+ * __put_user: - Write a simple value into user space, with less checking.
+ * @x:	 Value to copy to user space.
+ * @ptr: Destination address, in user space.
+ *
+ * Context: User context only. This function may sleep if pagefaults are
+ *          enabled.
+ *
+ * This macro copies a single simple value from kernel space to user
+ * space.  It supports simple types like char and int, but not larger
+ * data types like structures or arrays.
+ *
+ * @ptr must have pointer-to-simple-variable type, and @x must be assignable
+ * to the result of dereferencing @ptr.
+ *
+ * Caller must check the pointer with access_ok() before calling this
+ * function.
+ *
+ * Returns zero on success, or -EFAULT on error.
+ */
+#define __put_user(x, ptr)						\
+({									\
+	__typeof__(*(ptr)) __user *__pu_ptr = (ptr);			\
+	__typeof__(*(ptr)) __pu_val = (x);				\
+	int __pu_err = 0;						\
+									\
+	__chk_user_ptr(__pu_ptr);					\
+	switch (sizeof(*__pu_ptr)) {					\
+	case 1:								\
+		__put_data_asm(user_sb, __pu_ptr);			\
+		break;							\
+	case 2:								\
+		__put_data_asm(user_sh, __pu_ptr);			\
+		break;							\
+	case 4:								\
+		__put_data_asm(user_sw, __pu_ptr);			\
+		break;							\
+	case 8:								\
+		__PUT_DW(user_sd, __pu_ptr);				\
+		break;							\
+	default:							\
+		BUILD_BUG();						\
+	}								\
+									\
+	__pu_err;							\
+})
+
+/*
+ * __get_user: - Get a simple variable from user space, with less checking.
+ * @x:	 Variable to store result.
+ * @ptr: Source address, in user space.
+ *
+ * Context: User context only. This function may sleep if pagefaults are
+ *          enabled.
+ *
+ * This macro copies a single simple variable from user space to kernel
+ * space.  It supports simple types like char and int, but not larger
+ * data types like structures or arrays.
+ *
+ * @ptr must have pointer-to-simple-variable type, and the result of
+ * dereferencing @ptr must be assignable to @x without a cast.
+ *
+ * Caller must check the pointer with access_ok() before calling this
+ * function.
+ *
+ * Returns zero on success, or -EFAULT on error.
+ * On error, the variable @x is set to zero.
+ */
+#define __get_user(x, ptr)						\
+({									\
+	const __typeof__(*(ptr)) __user *__gu_ptr = (ptr);		\
+	int __gu_err = 0;						\
+									\
+	__chk_user_ptr(__gu_ptr);					\
+	switch (sizeof(*__gu_ptr)) {					\
+	case 1:								\
+		__get_data_asm((x), user_lb, __gu_ptr);			\
+		break;							\
+	case 2:								\
+		__get_data_asm((x), user_lh, __gu_ptr);			\
+		break;							\
+	case 4:								\
+		__get_data_asm((x), user_lw, __gu_ptr);			\
+		break;							\
+	case 8:								\
+		__GET_DW((x), user_ld, __gu_ptr);			\
+		break;							\
+	default:							\
+		BUILD_BUG();						\
+	}								\
+									\
+	__gu_err;							\
+})
+
+struct __large_struct { unsigned long buf[100]; };
+#define __m(x) (*(struct __large_struct __user *)(x))
+
+#ifdef CONFIG_32BIT
+#define __GET_DW(val, insn, ptr) __get_data_asm_ll32(val, insn, ptr)
+#endif
+#ifdef CONFIG_64BIT
+#define __GET_DW(val, insn, ptr) __get_data_asm(val, insn, ptr)
+#endif
+
+#define __get_data_asm(val, insn, addr)					\
+{									\
+	long __gu_tmp;							\
+									\
+	__asm__ __volatile__(						\
+	"1:	"insn("%1", "%3")"				\n"	\
+	"2:							\n"	\
+	"	.insn						\n"	\
+	"	.section .fixup,\"ax\"				\n"	\
+	"3:	li	%0, %4					\n"	\
+	"	move	%1, $0					\n"	\
+	"	j	2b					\n"	\
+	"	.previous					\n"	\
+	"	.section __ex_table,\"a\"			\n"	\
+	"	"__UA_ADDR "\t1b, 3b				\n"	\
+	"	.previous					\n"	\
+	: "=r" (__gu_err), "=r" (__gu_tmp)				\
+	: "0" (0), "o" (__m(addr)), "i" (-EFAULT));			\
+									\
+	(val) = (__typeof__(*(addr))) __gu_tmp;				\
+}
+
+/*
+ * Get a long long 64 using 32 bit registers.
+ */
+#define __get_data_asm_ll32(val, insn, addr)				\
+{									\
+	union {								\
+		unsigned long long	l;				\
+		__typeof__(*(addr))	t;				\
+	} __gu_tmp;							\
+									\
+	__asm__ __volatile__(						\
+	"1:	" insn("%1", "(%3)")"				\n"	\
+	"2:	" insn("%D1", "4(%3)")"				\n"	\
+	"3:							\n"	\
+	"	.insn						\n"	\
+	"	.section	.fixup,\"ax\"			\n"	\
+	"4:	li	%0, %4					\n"	\
+	"	move	%1, $0					\n"	\
+	"	move	%D1, $0					\n"	\
+	"	j	3b					\n"	\
+	"	.previous					\n"	\
+	"	.section	__ex_table,\"a\"		\n"	\
+	"	" __UA_ADDR "	1b, 4b				\n"	\
+	"	" __UA_ADDR "	2b, 4b				\n"	\
+	"	.previous					\n"	\
+	: "=r" (__gu_err), "=&r" (__gu_tmp.l)				\
+	: "0" (0), "r" (addr), "i" (-EFAULT));				\
+									\
+	(val) = __gu_tmp.t;						\
+}
+
+#define __get_kernel_nofault(dst, src, type, err_label)			\
+do {									\
+	int __gu_err;							\
+									\
+	switch (sizeof(type)) {						\
+	case 1:								\
+		__get_data_asm(*(type *)(dst), kernel_lb,		\
+			       (__force type *)(src));			\
+		break;							\
+	case 2:								\
+		__get_data_asm(*(type *)(dst), kernel_lh,		\
+			       (__force type *)(src));			\
+		break;							\
+	case 4:								\
+		 __get_data_asm(*(type *)(dst), kernel_lw,		\
+			       (__force type *)(src));			\
+		break;							\
+	case 8:								\
+		__GET_DW(*(type *)(dst), kernel_ld,			\
+			 (__force type *)(src));			\
+		break;							\
+	default:							\
+		BUILD_BUG();						\
+		break;							\
+	}								\
+	if (unlikely(__gu_err))						\
+		goto err_label;						\
+} while (0)
+
+/*
+ * Yuck.  We need two variants, one for 64bit operation and one
+ * for 32 bit mode and old iron.
+ */
+#ifdef CONFIG_32BIT
+#define __PUT_DW(insn, ptr) __put_data_asm_ll32(insn, ptr)
+#endif
+#ifdef CONFIG_64BIT
+#define __PUT_DW(insn, ptr) __put_data_asm(insn, ptr)
+#endif
+
+#define __put_data_asm(insn, ptr)					\
+{									\
+	__asm__ __volatile__(						\
+	"1:	"insn("%z2", "%3")"	# __put_data_asm	\n"	\
+	"2:							\n"	\
+	"	.insn						\n"	\
+	"	.section	.fixup,\"ax\"			\n"	\
+	"3:	li	%0, %4					\n"	\
+	"	j	2b					\n"	\
+	"	.previous					\n"	\
+	"	.section	__ex_table,\"a\"		\n"	\
+	"	" __UA_ADDR "	1b, 3b				\n"	\
+	"	.previous					\n"	\
+	: "=r" (__pu_err)						\
+	: "0" (0), "Jr" (__pu_val), "o" (__m(ptr)),			\
+	  "i" (-EFAULT));						\
+}
+
+#define __put_data_asm_ll32(insn, ptr)					\
+{									\
+	__asm__ __volatile__(						\
+	"1:	"insn("%2", "(%3)")"	# __put_data_asm_ll32	\n"	\
+	"2:	"insn("%D2", "4(%3)")"				\n"	\
+	"3:							\n"	\
+	"	.insn						\n"	\
+	"	.section	.fixup,\"ax\"			\n"	\
+	"4:	li	%0, %4					\n"	\
+	"	j	3b					\n"	\
+	"	.previous					\n"	\
+	"	.section	__ex_table,\"a\"		\n"	\
+	"	" __UA_ADDR "	1b, 4b				\n"	\
+	"	" __UA_ADDR "	2b, 4b				\n"	\
+	"	.previous"						\
+	: "=r" (__pu_err)						\
+	: "0" (0), "r" (__pu_val), "r" (ptr),				\
+	  "i" (-EFAULT));						\
+}
+
+#define __put_kernel_nofault(dst, src, type, err_label)			\
+do {									\
+	type __pu_val;					\
+	int __pu_err = 0;						\
+									\
+	__pu_val = *(__force type *)(src);				\
+	switch (sizeof(type)) {						\
+	case 1:								\
+		__put_data_asm(kernel_sb, (type *)(dst));		\
+		break;							\
+	case 2:								\
+		__put_data_asm(kernel_sh, (type *)(dst));		\
+		break;							\
+	case 4:								\
+		__put_data_asm(kernel_sw, (type *)(dst))		\
+		break;							\
+	case 8:								\
+		__PUT_DW(kernel_sd, (type *)(dst));			\
+		break;							\
+	default:							\
+		BUILD_BUG();						\
+		break;							\
+	}								\
+	if (unlikely(__pu_err))						\
+		goto err_label;						\
+} while (0)
+
+
+/*
+ * We're generating jump to subroutines which will be outside the range of
+ * jump instructions
+ */
+#ifdef MODULE
+#define __MODULE_JAL(destination)					\
+	".set\tnoat\n\t"						\
+	__UA_LA "\t$1, " #destination "\n\t"				\
+	"jalr\t$1\n\t"							\
+	".set\tat\n\t"
+#else
+#define __MODULE_JAL(destination)					\
+	"jal\t" #destination "\n\t"
+#endif
+
+#if defined(CONFIG_CPU_DADDI_WORKAROUNDS) || (defined(CONFIG_EVA) &&	\
+					      defined(CONFIG_CPU_HAS_PREFETCH))
+#define DADDI_SCRATCH "$3"
+#else
+#define DADDI_SCRATCH "$0"
+#endif
+
+extern size_t __raw_copy_from_user(void *__to, const void *__from, size_t __n);
+extern size_t __raw_copy_to_user(void *__to, const void *__from, size_t __n);
+
+static inline unsigned long
+raw_copy_from_user(void *to, const void __user *from, unsigned long n)
+{
+	register void *__cu_to_r __asm__("$4");
+	register const void __user *__cu_from_r __asm__("$5");
+	register long __cu_len_r __asm__("$6");
+
+	__cu_to_r = to;
+	__cu_from_r = from;
+	__cu_len_r = n;
+
+	__asm__ __volatile__(
+		".set\tnoreorder\n\t"
+		__MODULE_JAL(__raw_copy_from_user)
+		".set\tnoat\n\t"
+		__UA_ADDU "\t$1, %1, %2\n\t"
+		".set\tat\n\t"
+		".set\treorder"
+		: "+r" (__cu_to_r), "+r" (__cu_from_r), "+r" (__cu_len_r)
+		:
+		: "$8", "$9", "$10", "$11", "$12", "$14", "$15", "$24", "$31",
+		  DADDI_SCRATCH, "memory");
+
+	return __cu_len_r;
+}
+
+static inline unsigned long
+raw_copy_to_user(void __user *to, const void *from, unsigned long n)
+{
+	register void __user *__cu_to_r __asm__("$4");
+	register const void *__cu_from_r __asm__("$5");
+	register long __cu_len_r __asm__("$6");
+
+	__cu_to_r = (to);
+	__cu_from_r = (from);
+	__cu_len_r = (n);
+
+	__asm__ __volatile__(
+		__MODULE_JAL(__raw_copy_to_user)
+		: "+r" (__cu_to_r), "+r" (__cu_from_r), "+r" (__cu_len_r)
+		:
+		: "$8", "$9", "$10", "$11", "$12", "$14", "$15", "$24", "$31",
+		  DADDI_SCRATCH, "memory");
+
+	return __cu_len_r;
+}
+
+#define INLINE_COPY_FROM_USER
+#define INLINE_COPY_TO_USER
+
+extern __kernel_size_t __bzero(void __user *addr, __kernel_size_t size);
+
+/*
+ * __clear_user: - Zero a block of memory in user space, with less checking.
+ * @to:	  Destination address, in user space.
+ * @n:	  Number of bytes to zero.
+ *
+ * Zero a block of memory in user space.  Caller must check
+ * the specified block with access_ok() before calling this function.
+ *
+ * Returns number of bytes that could not be cleared.
+ * On success, this will be zero.
+ */
+static inline __kernel_size_t
+__clear_user(void __user *addr, __kernel_size_t size)
+{
+	__kernel_size_t res;
+
+#ifdef CONFIG_CPU_MICROMIPS
+/* micromips memset / bzero also clobbers t7 & t8 */
+#define bzero_clobbers "$4", "$5", "$6", __UA_t0, __UA_t1, "$15", "$24", "$31"
+#else
+#define bzero_clobbers "$4", "$5", "$6", __UA_t0, __UA_t1, "$31"
+#endif /* CONFIG_CPU_MICROMIPS */
+
+	might_fault();
+	__asm__ __volatile__(
+		"move\t$4, %1\n\t"
+		"move\t$5, $0\n\t"
+		"move\t$6, %2\n\t"
+		__MODULE_JAL(__bzero)
+		"move\t%0, $6"
+		: "=r" (res)
+		: "r" (addr), "r" (size)
+		: bzero_clobbers);
+
+	return res;
+}
+
+#define clear_user(addr,n)						\
+({									\
+	void __user * __cl_addr = (addr);				\
+	unsigned long __cl_size = (n);					\
+	if (__cl_size && access_ok(__cl_addr, __cl_size))		\
+		__cl_size = __clear_user(__cl_addr, __cl_size);		\
+	__cl_size;							\
+})
+
+extern long __strncpy_from_user_asm(char *__to, const char __user *__from, long __len);
+
+/*
+ * strncpy_from_user: - Copy a NUL terminated string from userspace.
+ * @dst:   Destination address, in kernel space.  This buffer must be at
+ *	   least @count bytes long.
+ * @src:   Source address, in user space.
+ * @count: Maximum number of bytes to copy, including the trailing NUL.
+ *
+ * Copies a NUL-terminated string from userspace to kernel space.
+ *
+ * On success, returns the length of the string (not including the trailing
+ * NUL).
+ *
+ * If access to userspace fails, returns -EFAULT (some data may have been
+ * copied).
+ *
+ * If @count is smaller than the length of the string, copies @count bytes
+ * and returns @count.
+ */
+static inline long
+strncpy_from_user(char *__to, const char __user *__from, long __len)
+{
+	long res;
+
+	if (!access_ok(__from, __len))
+		return -EFAULT;
+
+	might_fault();
+	__asm__ __volatile__(
+		"move\t$4, %1\n\t"
+		"move\t$5, %2\n\t"
+		"move\t$6, %3\n\t"
+		__MODULE_JAL(__strncpy_from_user_asm)
+		"move\t%0, $2"
+		: "=r" (res)
+		: "r" (__to), "r" (__from), "r" (__len)
+		: "$2", "$3", "$4", "$5", "$6", __UA_t0, "$31", "memory");
+
+	return res;
+}
+
+extern long __strnlen_user_asm(const char __user *s, long n);
+
+/*
+ * strnlen_user: - Get the size of a string in user space.
+ * @str: The string to measure.
+ *
+ * Context: User context only. This function may sleep if pagefaults are
+ *          enabled.
+ *
+ * Get the size of a NUL-terminated string in user space.
+ *
+ * Returns the size of the string INCLUDING the terminating NUL.
+ * On exception, returns 0.
+ * If the string is too long, returns a value greater than @n.
+ */
+static inline long strnlen_user(const char __user *s, long n)
+{
+	long res;
+
+	if (!access_ok(s, 1))
+		return 0;
+
+	might_fault();
+	__asm__ __volatile__(
+		"move\t$4, %1\n\t"
+		"move\t$5, %2\n\t"
+		__MODULE_JAL(__strnlen_user_asm)
+		"move\t%0, $2"
+		: "=r" (res)
+		: "r" (s), "r" (n)
+		: "$2", "$4", "$5", __UA_t0, "$31");
+
+	return res;
+}
+
+#endif /* _ASM_UACCESS_H */
diff --git a/arch/mips/include/asm/uasm.h b/arch/mips/include/asm/uasm.h
new file mode 100644
index 000000000..296bcf31a
--- /dev/null
+++ b/arch/mips/include/asm/uasm.h
@@ -0,0 +1,330 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2004, 2005, 2006, 2008	 Thiemo Seufer
+ * Copyright (C) 2005  Maciej W. Rozycki
+ * Copyright (C) 2006  Ralf Baechle (ralf@linux-mips.org)
+ * Copyright (C) 2012, 2013  MIPS Technologies, Inc.  All rights reserved.
+ */
+
+#ifndef __ASM_UASM_H
+#define __ASM_UASM_H
+
+#include <linux/types.h>
+
+#ifdef CONFIG_EXPORT_UASM
+#include <linux/export.h>
+#define UASM_EXPORT_SYMBOL(sym) EXPORT_SYMBOL(sym)
+#else
+#define UASM_EXPORT_SYMBOL(sym)
+#endif
+
+#define Ip_u1u2u3(op)							\
+void uasm_i##op(u32 **buf, unsigned int a, unsigned int b, unsigned int c)
+
+#define Ip_u2u1u3(op)							\
+void uasm_i##op(u32 **buf, unsigned int a, unsigned int b, unsigned int c)
+
+#define Ip_u3u2u1(op)							\
+void uasm_i##op(u32 **buf, unsigned int a, unsigned int b, unsigned int c)
+
+#define Ip_u3u1u2(op)							\
+void uasm_i##op(u32 **buf, unsigned int a, unsigned int b, unsigned int c)
+
+#define Ip_u1u2s3(op)							\
+void uasm_i##op(u32 **buf, unsigned int a, unsigned int b, signed int c)
+
+#define Ip_u2s3u1(op)							\
+void uasm_i##op(u32 **buf, unsigned int a, signed int b, unsigned int c)
+
+#define Ip_s3s1s2(op)							\
+void uasm_i##op(u32 **buf, int a, int b, int c)
+
+#define Ip_u2u1s3(op)							\
+void uasm_i##op(u32 **buf, unsigned int a, unsigned int b, signed int c)
+
+#define Ip_u2u1msbu3(op)						\
+void uasm_i##op(u32 **buf, unsigned int a, unsigned int b, unsigned int c, \
+	   unsigned int d)
+
+#define Ip_u1u2(op)							\
+void uasm_i##op(u32 **buf, unsigned int a, unsigned int b)
+
+#define Ip_u2u1(op)							\
+void uasm_i##op(u32 **buf, unsigned int a, unsigned int b)
+
+#define Ip_u1s2(op)							\
+void uasm_i##op(u32 **buf, unsigned int a, signed int b)
+
+#define Ip_u1(op) void uasm_i##op(u32 **buf, unsigned int a)
+
+#define Ip_0(op) void uasm_i##op(u32 **buf)
+
+Ip_u2u1s3(_addiu);
+Ip_u3u1u2(_addu);
+Ip_u3u1u2(_and);
+Ip_u2u1u3(_andi);
+Ip_u1u2s3(_bbit0);
+Ip_u1u2s3(_bbit1);
+Ip_u1u2s3(_beq);
+Ip_u1u2s3(_beql);
+Ip_u1s2(_bgez);
+Ip_u1s2(_bgezl);
+Ip_u1s2(_bgtz);
+Ip_u1s2(_blez);
+Ip_u1s2(_bltz);
+Ip_u1s2(_bltzl);
+Ip_u1u2s3(_bne);
+Ip_u1(_break);
+Ip_u2s3u1(_cache);
+Ip_u1u2(_cfc1);
+Ip_u2u1(_cfcmsa);
+Ip_u1u2(_ctc1);
+Ip_u2u1(_ctcmsa);
+Ip_u2u1s3(_daddiu);
+Ip_u3u1u2(_daddu);
+Ip_u1u2(_ddivu);
+Ip_u3u1u2(_ddivu_r6);
+Ip_u1(_di);
+Ip_u2u1msbu3(_dins);
+Ip_u2u1msbu3(_dinsm);
+Ip_u2u1msbu3(_dinsu);
+Ip_u1u2(_divu);
+Ip_u3u1u2(_divu_r6);
+Ip_u1u2u3(_dmfc0);
+Ip_u3u1u2(_dmodu);
+Ip_u1u2u3(_dmtc0);
+Ip_u1u2(_dmultu);
+Ip_u3u1u2(_dmulu);
+Ip_u2u1u3(_drotr);
+Ip_u2u1u3(_drotr32);
+Ip_u2u1(_dsbh);
+Ip_u2u1(_dshd);
+Ip_u2u1u3(_dsll);
+Ip_u2u1u3(_dsll32);
+Ip_u3u2u1(_dsllv);
+Ip_u2u1u3(_dsra);
+Ip_u2u1u3(_dsra32);
+Ip_u3u2u1(_dsrav);
+Ip_u2u1u3(_dsrl);
+Ip_u2u1u3(_dsrl32);
+Ip_u3u2u1(_dsrlv);
+Ip_u3u1u2(_dsubu);
+Ip_0(_eret);
+Ip_u2u1msbu3(_ext);
+Ip_u2u1msbu3(_ins);
+Ip_u1(_j);
+Ip_u1(_jal);
+Ip_u2u1(_jalr);
+Ip_u1(_jr);
+Ip_u2s3u1(_lb);
+Ip_u2s3u1(_lbu);
+Ip_u2s3u1(_ld);
+Ip_u3u1u2(_ldx);
+Ip_u2s3u1(_lh);
+Ip_u2s3u1(_lhu);
+Ip_u2s3u1(_ll);
+Ip_u2s3u1(_lld);
+Ip_u1s2(_lui);
+Ip_u2s3u1(_lw);
+Ip_u2s3u1(_lwu);
+Ip_u3u1u2(_lwx);
+Ip_u1u2u3(_mfc0);
+Ip_u1u2u3(_mfhc0);
+Ip_u1(_mfhi);
+Ip_u1(_mflo);
+Ip_u3u1u2(_modu);
+Ip_u3u1u2(_movn);
+Ip_u3u1u2(_movz);
+Ip_u1u2u3(_mtc0);
+Ip_u1u2u3(_mthc0);
+Ip_u1(_mthi);
+Ip_u1(_mtlo);
+Ip_u3u1u2(_mul);
+Ip_u1u2(_multu);
+Ip_u3u1u2(_mulu);
+Ip_u3u1u2(_muhu);
+Ip_u3u1u2(_nor);
+Ip_u3u1u2(_or);
+Ip_u2u1u3(_ori);
+Ip_u2s3u1(_pref);
+Ip_0(_rfe);
+Ip_u2u1u3(_rotr);
+Ip_u2s3u1(_sb);
+Ip_u2s3u1(_sc);
+Ip_u2s3u1(_scd);
+Ip_u2s3u1(_sd);
+Ip_u3u1u2(_seleqz);
+Ip_u3u1u2(_selnez);
+Ip_u2s3u1(_sh);
+Ip_u2u1u3(_sll);
+Ip_u3u2u1(_sllv);
+Ip_s3s1s2(_slt);
+Ip_u2u1s3(_slti);
+Ip_u2u1s3(_sltiu);
+Ip_u3u1u2(_sltu);
+Ip_u2u1u3(_sra);
+Ip_u3u2u1(_srav);
+Ip_u2u1u3(_srl);
+Ip_u3u2u1(_srlv);
+Ip_u3u1u2(_subu);
+Ip_u2s3u1(_sw);
+Ip_u1(_sync);
+Ip_u1(_syscall);
+Ip_0(_tlbp);
+Ip_0(_tlbr);
+Ip_0(_tlbwi);
+Ip_0(_tlbwr);
+Ip_u1(_wait);
+Ip_u2u1(_wsbh);
+Ip_u3u1u2(_xor);
+Ip_u2u1u3(_xori);
+Ip_u2u1(_yield);
+Ip_u1u2(_ldpte);
+Ip_u2u1u3(_lddir);
+
+/* Handle labels. */
+struct uasm_label {
+	u32 *addr;
+	int lab;
+};
+
+void uasm_build_label(struct uasm_label **lab, u32 *addr,
+			int lid);
+#ifdef CONFIG_64BIT
+int uasm_in_compat_space_p(long addr);
+#endif
+int uasm_rel_hi(long val);
+int uasm_rel_lo(long val);
+void UASM_i_LA_mostly(u32 **buf, unsigned int rs, long addr);
+void UASM_i_LA(u32 **buf, unsigned int rs, long addr);
+
+#define UASM_L_LA(lb)							\
+static inline void uasm_l##lb(struct uasm_label **lab, u32 *addr)	\
+{									\
+	uasm_build_label(lab, addr, label##lb);				\
+}
+
+/* convenience macros for instructions */
+#ifdef CONFIG_64BIT
+# define UASM_i_ADDIU(buf, rs, rt, val) uasm_i_daddiu(buf, rs, rt, val)
+# define UASM_i_ADDU(buf, rs, rt, rd) uasm_i_daddu(buf, rs, rt, rd)
+# define UASM_i_LL(buf, rs, rt, off) uasm_i_lld(buf, rs, rt, off)
+# define UASM_i_LW(buf, rs, rt, off) uasm_i_ld(buf, rs, rt, off)
+# define UASM_i_LWX(buf, rs, rt, rd) uasm_i_ldx(buf, rs, rt, rd)
+# define UASM_i_MFC0(buf, rt, rd...) uasm_i_dmfc0(buf, rt, rd)
+# define UASM_i_MTC0(buf, rt, rd...) uasm_i_dmtc0(buf, rt, rd)
+# define UASM_i_ROTR(buf, rs, rt, sh) uasm_i_drotr(buf, rs, rt, sh)
+# define UASM_i_SC(buf, rs, rt, off) uasm_i_scd(buf, rs, rt, off)
+# define UASM_i_SLL(buf, rs, rt, sh) uasm_i_dsll(buf, rs, rt, sh)
+# define UASM_i_SRA(buf, rs, rt, sh) uasm_i_dsra(buf, rs, rt, sh)
+# define UASM_i_SRL(buf, rs, rt, sh) uasm_i_dsrl(buf, rs, rt, sh)
+# define UASM_i_SRL_SAFE(buf, rs, rt, sh) uasm_i_dsrl_safe(buf, rs, rt, sh)
+# define UASM_i_SUBU(buf, rs, rt, rd) uasm_i_dsubu(buf, rs, rt, rd)
+# define UASM_i_SW(buf, rs, rt, off) uasm_i_sd(buf, rs, rt, off)
+#else
+# define UASM_i_ADDIU(buf, rs, rt, val) uasm_i_addiu(buf, rs, rt, val)
+# define UASM_i_ADDU(buf, rs, rt, rd) uasm_i_addu(buf, rs, rt, rd)
+# define UASM_i_LL(buf, rs, rt, off) uasm_i_ll(buf, rs, rt, off)
+# define UASM_i_LW(buf, rs, rt, off) uasm_i_lw(buf, rs, rt, off)
+# define UASM_i_LWX(buf, rs, rt, rd) uasm_i_lwx(buf, rs, rt, rd)
+# define UASM_i_MFC0(buf, rt, rd...) uasm_i_mfc0(buf, rt, rd)
+# define UASM_i_MTC0(buf, rt, rd...) uasm_i_mtc0(buf, rt, rd)
+# define UASM_i_ROTR(buf, rs, rt, sh) uasm_i_rotr(buf, rs, rt, sh)
+# define UASM_i_SC(buf, rs, rt, off) uasm_i_sc(buf, rs, rt, off)
+# define UASM_i_SLL(buf, rs, rt, sh) uasm_i_sll(buf, rs, rt, sh)
+# define UASM_i_SRA(buf, rs, rt, sh) uasm_i_sra(buf, rs, rt, sh)
+# define UASM_i_SRL(buf, rs, rt, sh) uasm_i_srl(buf, rs, rt, sh)
+# define UASM_i_SRL_SAFE(buf, rs, rt, sh) uasm_i_srl(buf, rs, rt, sh)
+# define UASM_i_SUBU(buf, rs, rt, rd) uasm_i_subu(buf, rs, rt, rd)
+# define UASM_i_SW(buf, rs, rt, off) uasm_i_sw(buf, rs, rt, off)
+#endif
+
+#define uasm_i_b(buf, off) uasm_i_beq(buf, 0, 0, off)
+#define uasm_i_beqz(buf, rs, off) uasm_i_beq(buf, rs, 0, off)
+#define uasm_i_beqzl(buf, rs, off) uasm_i_beql(buf, rs, 0, off)
+#define uasm_i_bnez(buf, rs, off) uasm_i_bne(buf, rs, 0, off)
+#define uasm_i_bnezl(buf, rs, off) uasm_i_bnel(buf, rs, 0, off)
+#define uasm_i_ehb(buf) uasm_i_sll(buf, 0, 0, 3)
+#define uasm_i_move(buf, a, b) UASM_i_ADDU(buf, a, 0, b)
+#ifdef CONFIG_CPU_NOP_WORKAROUNDS
+#define uasm_i_nop(buf) uasm_i_or(buf, 1, 1, 0)
+#else
+#define uasm_i_nop(buf) uasm_i_sll(buf, 0, 0, 0)
+#endif
+#define uasm_i_ssnop(buf) uasm_i_sll(buf, 0, 0, 1)
+
+static inline void uasm_i_drotr_safe(u32 **p, unsigned int a1,
+				     unsigned int a2, unsigned int a3)
+{
+	if (a3 < 32)
+		uasm_i_drotr(p, a1, a2, a3);
+	else
+		uasm_i_drotr32(p, a1, a2, a3 - 32);
+}
+
+static inline void uasm_i_dsll_safe(u32 **p, unsigned int a1,
+				    unsigned int a2, unsigned int a3)
+{
+	if (a3 < 32)
+		uasm_i_dsll(p, a1, a2, a3);
+	else
+		uasm_i_dsll32(p, a1, a2, a3 - 32);
+}
+
+static inline void uasm_i_dsrl_safe(u32 **p, unsigned int a1,
+				    unsigned int a2, unsigned int a3)
+{
+	if (a3 < 32)
+		uasm_i_dsrl(p, a1, a2, a3);
+	else
+		uasm_i_dsrl32(p, a1, a2, a3 - 32);
+}
+
+static inline void uasm_i_dsra_safe(u32 **p, unsigned int a1,
+				    unsigned int a2, unsigned int a3)
+{
+	if (a3 < 32)
+		uasm_i_dsra(p, a1, a2, a3);
+	else
+		uasm_i_dsra32(p, a1, a2, a3 - 32);
+}
+
+/* Handle relocations. */
+struct uasm_reloc {
+	u32 *addr;
+	unsigned int type;
+	int lab;
+};
+
+/* This is zero so we can use zeroed label arrays. */
+#define UASM_LABEL_INVALID 0
+
+void uasm_r_mips_pc16(struct uasm_reloc **rel, u32 *addr, int lid);
+void uasm_resolve_relocs(struct uasm_reloc *rel, struct uasm_label *lab);
+void uasm_move_relocs(struct uasm_reloc *rel, u32 *first, u32 *end, long off);
+void uasm_move_labels(struct uasm_label *lab, u32 *first, u32 *end, long off);
+void uasm_copy_handler(struct uasm_reloc *rel, struct uasm_label *lab,
+	u32 *first, u32 *end, u32 *target);
+int uasm_insn_has_bdelay(struct uasm_reloc *rel, u32 *addr);
+
+/* Convenience functions for labeled branches. */
+void uasm_il_b(u32 **p, struct uasm_reloc **r, int lid);
+void uasm_il_bbit0(u32 **p, struct uasm_reloc **r, unsigned int reg,
+		   unsigned int bit, int lid);
+void uasm_il_bbit1(u32 **p, struct uasm_reloc **r, unsigned int reg,
+		   unsigned int bit, int lid);
+void uasm_il_beq(u32 **p, struct uasm_reloc **r, unsigned int r1,
+		 unsigned int r2, int lid);
+void uasm_il_beqz(u32 **p, struct uasm_reloc **r, unsigned int reg, int lid);
+void uasm_il_beqzl(u32 **p, struct uasm_reloc **r, unsigned int reg, int lid);
+void uasm_il_bgezl(u32 **p, struct uasm_reloc **r, unsigned int reg, int lid);
+void uasm_il_bgez(u32 **p, struct uasm_reloc **r, unsigned int reg, int lid);
+void uasm_il_bltz(u32 **p, struct uasm_reloc **r, unsigned int reg, int lid);
+void uasm_il_bne(u32 **p, struct uasm_reloc **r, unsigned int reg1,
+		 unsigned int reg2, int lid);
+void uasm_il_bnez(u32 **p, struct uasm_reloc **r, unsigned int reg, int lid);
+
+#endif /* __ASM_UASM_H */
diff --git a/arch/mips/include/asm/unaligned-emul.h b/arch/mips/include/asm/unaligned-emul.h
new file mode 100644
index 000000000..9af0f4d3d
--- /dev/null
+++ b/arch/mips/include/asm/unaligned-emul.h
@@ -0,0 +1,779 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+#ifndef _ASM_MIPS_UNALIGNED_EMUL_H
+#define _ASM_MIPS_UNALIGNED_EMUL_H
+
+#include <asm/asm.h>
+
+#ifdef __BIG_ENDIAN
+#define  _LoadHW(addr, value, res, type)  \
+do {                                                \
+	__asm__ __volatile__ (".set\tnoat\n"        \
+		"1:\t"type##_lb("%0", "0(%2)")"\n"  \
+		"2:\t"type##_lbu("$1", "1(%2)")"\n\t"\
+		"sll\t%0, 0x8\n\t"                  \
+		"or\t%0, $1\n\t"                    \
+		"li\t%1, 0\n"                       \
+		"3:\t.set\tat\n\t"                  \
+		".insn\n\t"                         \
+		".section\t.fixup,\"ax\"\n\t"       \
+		"4:\tli\t%1, %3\n\t"                \
+		"j\t3b\n\t"                         \
+		".previous\n\t"                     \
+		".section\t__ex_table,\"a\"\n\t"    \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
+		".previous"                         \
+		: "=&r" (value), "=r" (res)         \
+		: "r" (addr), "i" (-EFAULT));       \
+} while (0)
+
+#ifndef CONFIG_CPU_NO_LOAD_STORE_LR
+#define  _LoadW(addr, value, res, type)   \
+do {                                                \
+	__asm__ __volatile__ (                      \
+		"1:\t"type##_lwl("%0", "(%2)")"\n"   \
+		"2:\t"type##_lwr("%0", "3(%2)")"\n\t"\
+		"li\t%1, 0\n"                       \
+		"3:\n\t"                            \
+		".insn\n\t"                         \
+		".section\t.fixup,\"ax\"\n\t"       \
+		"4:\tli\t%1, %3\n\t"                \
+		"j\t3b\n\t"                         \
+		".previous\n\t"                     \
+		".section\t__ex_table,\"a\"\n\t"    \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
+		".previous"                         \
+		: "=&r" (value), "=r" (res)         \
+		: "r" (addr), "i" (-EFAULT));       \
+} while (0)
+
+#else /* CONFIG_CPU_NO_LOAD_STORE_LR */
+/* For CPUs without lwl instruction */
+#define  _LoadW(addr, value, res, type) \
+do {                                                \
+	__asm__ __volatile__ (			    \
+		".set\tpush\n"			    \
+		".set\tnoat\n\t"		    \
+		"1:"type##_lb("%0", "0(%2)")"\n\t"  \
+		"2:"type##_lbu("$1", "1(%2)")"\n\t" \
+		"sll\t%0, 0x8\n\t"		    \
+		"or\t%0, $1\n\t"		    \
+		"3:"type##_lbu("$1", "2(%2)")"\n\t" \
+		"sll\t%0, 0x8\n\t"		    \
+		"or\t%0, $1\n\t"		    \
+		"4:"type##_lbu("$1", "3(%2)")"\n\t" \
+		"sll\t%0, 0x8\n\t"		    \
+		"or\t%0, $1\n\t"		    \
+		"li\t%1, 0\n"			    \
+		".set\tpop\n"			    \
+		"10:\n\t"			    \
+		".insn\n\t"			    \
+		".section\t.fixup,\"ax\"\n\t"	    \
+		"11:\tli\t%1, %3\n\t"		    \
+		"j\t10b\n\t"			    \
+		".previous\n\t"			    \
+		".section\t__ex_table,\"a\"\n\t"    \
+		STR(PTR_WD)"\t1b, 11b\n\t"	    \
+		STR(PTR_WD)"\t2b, 11b\n\t"	    \
+		STR(PTR_WD)"\t3b, 11b\n\t"	    \
+		STR(PTR_WD)"\t4b, 11b\n\t"	    \
+		".previous"			    \
+		: "=&r" (value), "=r" (res)	    \
+		: "r" (addr), "i" (-EFAULT));       \
+} while (0)
+
+#endif /* CONFIG_CPU_NO_LOAD_STORE_LR */
+
+#define  _LoadHWU(addr, value, res, type) \
+do {                                                \
+	__asm__ __volatile__ (                      \
+		".set\tnoat\n"                      \
+		"1:\t"type##_lbu("%0", "0(%2)")"\n" \
+		"2:\t"type##_lbu("$1", "1(%2)")"\n\t"\
+		"sll\t%0, 0x8\n\t"                  \
+		"or\t%0, $1\n\t"                    \
+		"li\t%1, 0\n"                       \
+		"3:\n\t"                            \
+		".insn\n\t"                         \
+		".set\tat\n\t"                      \
+		".section\t.fixup,\"ax\"\n\t"       \
+		"4:\tli\t%1, %3\n\t"                \
+		"j\t3b\n\t"                         \
+		".previous\n\t"                     \
+		".section\t__ex_table,\"a\"\n\t"    \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
+		".previous"                         \
+		: "=&r" (value), "=r" (res)         \
+		: "r" (addr), "i" (-EFAULT));       \
+} while (0)
+
+#ifndef CONFIG_CPU_NO_LOAD_STORE_LR
+#define  _LoadWU(addr, value, res, type)  \
+do {                                                \
+	__asm__ __volatile__ (                      \
+		"1:\t"type##_lwl("%0", "(%2)")"\n"  \
+		"2:\t"type##_lwr("%0", "3(%2)")"\n\t"\
+		"dsll\t%0, %0, 32\n\t"              \
+		"dsrl\t%0, %0, 32\n\t"              \
+		"li\t%1, 0\n"                       \
+		"3:\n\t"                            \
+		".insn\n\t"                         \
+		"\t.section\t.fixup,\"ax\"\n\t"     \
+		"4:\tli\t%1, %3\n\t"                \
+		"j\t3b\n\t"                         \
+		".previous\n\t"                     \
+		".section\t__ex_table,\"a\"\n\t"    \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
+		".previous"                         \
+		: "=&r" (value), "=r" (res)         \
+		: "r" (addr), "i" (-EFAULT));       \
+} while (0)
+
+#define  _LoadDW(addr, value, res)  \
+do {                                                \
+	__asm__ __volatile__ (                      \
+		"1:\tldl\t%0, (%2)\n"               \
+		"2:\tldr\t%0, 7(%2)\n\t"            \
+		"li\t%1, 0\n"                       \
+		"3:\n\t"                            \
+		".insn\n\t"                         \
+		"\t.section\t.fixup,\"ax\"\n\t"     \
+		"4:\tli\t%1, %3\n\t"                \
+		"j\t3b\n\t"                         \
+		".previous\n\t"                     \
+		".section\t__ex_table,\"a\"\n\t"    \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
+		".previous"                         \
+		: "=&r" (value), "=r" (res)         \
+		: "r" (addr), "i" (-EFAULT));       \
+} while (0)
+
+#else /* CONFIG_CPU_NO_LOAD_STORE_LR */
+/* For CPUs without lwl and ldl instructions */
+#define  _LoadWU(addr, value, res, type) \
+do {                                                \
+	__asm__ __volatile__ (			    \
+		".set\tpush\n\t"		    \
+		".set\tnoat\n\t"		    \
+		"1:"type##_lbu("%0", "0(%2)")"\n\t" \
+		"2:"type##_lbu("$1", "1(%2)")"\n\t" \
+		"sll\t%0, 0x8\n\t"		    \
+		"or\t%0, $1\n\t"		    \
+		"3:"type##_lbu("$1", "2(%2)")"\n\t" \
+		"sll\t%0, 0x8\n\t"		    \
+		"or\t%0, $1\n\t"		    \
+		"4:"type##_lbu("$1", "3(%2)")"\n\t" \
+		"sll\t%0, 0x8\n\t"		    \
+		"or\t%0, $1\n\t"		    \
+		"li\t%1, 0\n"			    \
+		".set\tpop\n"			    \
+		"10:\n\t"			    \
+		".insn\n\t"			    \
+		".section\t.fixup,\"ax\"\n\t"	    \
+		"11:\tli\t%1, %3\n\t"		    \
+		"j\t10b\n\t"			    \
+		".previous\n\t"			    \
+		".section\t__ex_table,\"a\"\n\t"    \
+		STR(PTR_WD)"\t1b, 11b\n\t"	    \
+		STR(PTR_WD)"\t2b, 11b\n\t"	    \
+		STR(PTR_WD)"\t3b, 11b\n\t"	    \
+		STR(PTR_WD)"\t4b, 11b\n\t"	    \
+		".previous"			    \
+		: "=&r" (value), "=r" (res)	    \
+		: "r" (addr), "i" (-EFAULT));       \
+} while (0)
+
+#define  _LoadDW(addr, value, res)  \
+do {                                                \
+	__asm__ __volatile__ (			    \
+		".set\tpush\n\t"		    \
+		".set\tnoat\n\t"		    \
+		"1:lb\t%0, 0(%2)\n\t"		    \
+		"2:lbu\t $1, 1(%2)\n\t"		    \
+		"dsll\t%0, 0x8\n\t"		    \
+		"or\t%0, $1\n\t"		    \
+		"3:lbu\t$1, 2(%2)\n\t"		    \
+		"dsll\t%0, 0x8\n\t"		    \
+		"or\t%0, $1\n\t"		    \
+		"4:lbu\t$1, 3(%2)\n\t"		    \
+		"dsll\t%0, 0x8\n\t"		    \
+		"or\t%0, $1\n\t"		    \
+		"5:lbu\t$1, 4(%2)\n\t"		    \
+		"dsll\t%0, 0x8\n\t"		    \
+		"or\t%0, $1\n\t"		    \
+		"6:lbu\t$1, 5(%2)\n\t"		    \
+		"dsll\t%0, 0x8\n\t"		    \
+		"or\t%0, $1\n\t"		    \
+		"7:lbu\t$1, 6(%2)\n\t"		    \
+		"dsll\t%0, 0x8\n\t"		    \
+		"or\t%0, $1\n\t"		    \
+		"8:lbu\t$1, 7(%2)\n\t"		    \
+		"dsll\t%0, 0x8\n\t"		    \
+		"or\t%0, $1\n\t"		    \
+		"li\t%1, 0\n"			    \
+		".set\tpop\n\t"			    \
+		"10:\n\t"			    \
+		".insn\n\t"			    \
+		".section\t.fixup,\"ax\"\n\t"	    \
+		"11:\tli\t%1, %3\n\t"		    \
+		"j\t10b\n\t"			    \
+		".previous\n\t"			    \
+		".section\t__ex_table,\"a\"\n\t"    \
+		STR(PTR_WD)"\t1b, 11b\n\t"	    \
+		STR(PTR_WD)"\t2b, 11b\n\t"	    \
+		STR(PTR_WD)"\t3b, 11b\n\t"	    \
+		STR(PTR_WD)"\t4b, 11b\n\t"	    \
+		STR(PTR_WD)"\t5b, 11b\n\t"	    \
+		STR(PTR_WD)"\t6b, 11b\n\t"	    \
+		STR(PTR_WD)"\t7b, 11b\n\t"	    \
+		STR(PTR_WD)"\t8b, 11b\n\t"	    \
+		".previous"			    \
+		: "=&r" (value), "=r" (res)	    \
+		: "r" (addr), "i" (-EFAULT));       \
+} while (0)
+
+#endif /* CONFIG_CPU_NO_LOAD_STORE_LR */
+
+
+#define  _StoreHW(addr, value, res, type) \
+do {                                                \
+	__asm__ __volatile__ (                      \
+		".set\tnoat\n"                      \
+		"1:\t"type##_sb("%1", "1(%2)")"\n"  \
+		"srl\t$1, %1, 0x8\n"                \
+		"2:\t"type##_sb("$1", "0(%2)")"\n"  \
+		".set\tat\n\t"                      \
+		"li\t%0, 0\n"                       \
+		"3:\n\t"                            \
+		".insn\n\t"                         \
+		".section\t.fixup,\"ax\"\n\t"       \
+		"4:\tli\t%0, %3\n\t"                \
+		"j\t3b\n\t"                         \
+		".previous\n\t"                     \
+		".section\t__ex_table,\"a\"\n\t"    \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
+		".previous"                         \
+		: "=r" (res)                        \
+		: "r" (value), "r" (addr), "i" (-EFAULT));\
+} while (0)
+
+#ifndef CONFIG_CPU_NO_LOAD_STORE_LR
+#define  _StoreW(addr, value, res, type)  \
+do {                                                \
+	__asm__ __volatile__ (                      \
+		"1:\t"type##_swl("%1", "(%2)")"\n"  \
+		"2:\t"type##_swr("%1", "3(%2)")"\n\t"\
+		"li\t%0, 0\n"                       \
+		"3:\n\t"                            \
+		".insn\n\t"                         \
+		".section\t.fixup,\"ax\"\n\t"       \
+		"4:\tli\t%0, %3\n\t"                \
+		"j\t3b\n\t"                         \
+		".previous\n\t"                     \
+		".section\t__ex_table,\"a\"\n\t"    \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
+		".previous"                         \
+		: "=r" (res)                                \
+		: "r" (value), "r" (addr), "i" (-EFAULT));  \
+} while (0)
+
+#define  _StoreDW(addr, value, res) \
+do {                                                \
+	__asm__ __volatile__ (                      \
+		"1:\tsdl\t%1,(%2)\n"                \
+		"2:\tsdr\t%1, 7(%2)\n\t"            \
+		"li\t%0, 0\n"                       \
+		"3:\n\t"                            \
+		".insn\n\t"                         \
+		".section\t.fixup,\"ax\"\n\t"       \
+		"4:\tli\t%0, %3\n\t"                \
+		"j\t3b\n\t"                         \
+		".previous\n\t"                     \
+		".section\t__ex_table,\"a\"\n\t"    \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
+		".previous"                         \
+		: "=r" (res)                                \
+		: "r" (value), "r" (addr), "i" (-EFAULT));  \
+} while (0)
+
+#else /* CONFIG_CPU_NO_LOAD_STORE_LR */
+#define  _StoreW(addr, value, res, type)  \
+do {                                                \
+	__asm__ __volatile__ (                      \
+		".set\tpush\n\t"		    \
+		".set\tnoat\n\t"		    \
+		"1:"type##_sb("%1", "3(%2)")"\n\t"  \
+		"srl\t$1, %1, 0x8\n\t"		    \
+		"2:"type##_sb("$1", "2(%2)")"\n\t"  \
+		"srl\t$1, $1,  0x8\n\t"		    \
+		"3:"type##_sb("$1", "1(%2)")"\n\t"  \
+		"srl\t$1, $1, 0x8\n\t"		    \
+		"4:"type##_sb("$1", "0(%2)")"\n\t"  \
+		".set\tpop\n\t"			    \
+		"li\t%0, 0\n"			    \
+		"10:\n\t"			    \
+		".insn\n\t"			    \
+		".section\t.fixup,\"ax\"\n\t"	    \
+		"11:\tli\t%0, %3\n\t"		    \
+		"j\t10b\n\t"			    \
+		".previous\n\t"			    \
+		".section\t__ex_table,\"a\"\n\t"    \
+		STR(PTR_WD)"\t1b, 11b\n\t"	    \
+		STR(PTR_WD)"\t2b, 11b\n\t"	    \
+		STR(PTR_WD)"\t3b, 11b\n\t"	    \
+		STR(PTR_WD)"\t4b, 11b\n\t"	    \
+		".previous"			    \
+		: "=&r" (res)				    \
+		: "r" (value), "r" (addr), "i" (-EFAULT)    \
+		: "memory");                                \
+} while (0)
+
+#define  _StoreDW(addr, value, res) \
+do {                                                \
+	__asm__ __volatile__ (                      \
+		".set\tpush\n\t"		    \
+		".set\tnoat\n\t"		    \
+		"1:sb\t%1, 7(%2)\n\t"		    \
+		"dsrl\t$1, %1, 0x8\n\t"		    \
+		"2:sb\t$1, 6(%2)\n\t"		    \
+		"dsrl\t$1, $1, 0x8\n\t"		    \
+		"3:sb\t$1, 5(%2)\n\t"		    \
+		"dsrl\t$1, $1, 0x8\n\t"		    \
+		"4:sb\t$1, 4(%2)\n\t"		    \
+		"dsrl\t$1, $1, 0x8\n\t"		    \
+		"5:sb\t$1, 3(%2)\n\t"		    \
+		"dsrl\t$1, $1, 0x8\n\t"		    \
+		"6:sb\t$1, 2(%2)\n\t"		    \
+		"dsrl\t$1, $1, 0x8\n\t"		    \
+		"7:sb\t$1, 1(%2)\n\t"		    \
+		"dsrl\t$1, $1, 0x8\n\t"		    \
+		"8:sb\t$1, 0(%2)\n\t"		    \
+		"dsrl\t$1, $1, 0x8\n\t"		    \
+		".set\tpop\n\t"			    \
+		"li\t%0, 0\n"			    \
+		"10:\n\t"			    \
+		".insn\n\t"			    \
+		".section\t.fixup,\"ax\"\n\t"	    \
+		"11:\tli\t%0, %3\n\t"		    \
+		"j\t10b\n\t"			    \
+		".previous\n\t"			    \
+		".section\t__ex_table,\"a\"\n\t"    \
+		STR(PTR_WD)"\t1b, 11b\n\t"	    \
+		STR(PTR_WD)"\t2b, 11b\n\t"	    \
+		STR(PTR_WD)"\t3b, 11b\n\t"	    \
+		STR(PTR_WD)"\t4b, 11b\n\t"	    \
+		STR(PTR_WD)"\t5b, 11b\n\t"	    \
+		STR(PTR_WD)"\t6b, 11b\n\t"	    \
+		STR(PTR_WD)"\t7b, 11b\n\t"	    \
+		STR(PTR_WD)"\t8b, 11b\n\t"	    \
+		".previous"			    \
+		: "=&r" (res)				    \
+		: "r" (value), "r" (addr), "i" (-EFAULT)    \
+		: "memory");                                \
+} while (0)
+
+#endif /* CONFIG_CPU_NO_LOAD_STORE_LR */
+
+#else /* __BIG_ENDIAN */
+
+#define  _LoadHW(addr, value, res, type)  \
+do {                                                \
+	__asm__ __volatile__ (".set\tnoat\n"        \
+		"1:\t"type##_lb("%0", "1(%2)")"\n"  \
+		"2:\t"type##_lbu("$1", "0(%2)")"\n\t"\
+		"sll\t%0, 0x8\n\t"                  \
+		"or\t%0, $1\n\t"                    \
+		"li\t%1, 0\n"                       \
+		"3:\t.set\tat\n\t"                  \
+		".insn\n\t"                         \
+		".section\t.fixup,\"ax\"\n\t"       \
+		"4:\tli\t%1, %3\n\t"                \
+		"j\t3b\n\t"                         \
+		".previous\n\t"                     \
+		".section\t__ex_table,\"a\"\n\t"    \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
+		".previous"                         \
+		: "=&r" (value), "=r" (res)         \
+		: "r" (addr), "i" (-EFAULT));       \
+} while (0)
+
+#ifndef CONFIG_CPU_NO_LOAD_STORE_LR
+#define  _LoadW(addr, value, res, type)   \
+do {                                                \
+	__asm__ __volatile__ (                      \
+		"1:\t"type##_lwl("%0", "3(%2)")"\n" \
+		"2:\t"type##_lwr("%0", "(%2)")"\n\t"\
+		"li\t%1, 0\n"                       \
+		"3:\n\t"                            \
+		".insn\n\t"                         \
+		".section\t.fixup,\"ax\"\n\t"       \
+		"4:\tli\t%1, %3\n\t"                \
+		"j\t3b\n\t"                         \
+		".previous\n\t"                     \
+		".section\t__ex_table,\"a\"\n\t"    \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
+		".previous"                         \
+		: "=&r" (value), "=r" (res)         \
+		: "r" (addr), "i" (-EFAULT));       \
+} while (0)
+
+#else /* CONFIG_CPU_NO_LOAD_STORE_LR */
+/* For CPUs without lwl instruction */
+#define  _LoadW(addr, value, res, type) \
+do {                                                \
+	__asm__ __volatile__ (			    \
+		".set\tpush\n"			    \
+		".set\tnoat\n\t"		    \
+		"1:"type##_lb("%0", "3(%2)")"\n\t"  \
+		"2:"type##_lbu("$1", "2(%2)")"\n\t" \
+		"sll\t%0, 0x8\n\t"		    \
+		"or\t%0, $1\n\t"		    \
+		"3:"type##_lbu("$1", "1(%2)")"\n\t" \
+		"sll\t%0, 0x8\n\t"		    \
+		"or\t%0, $1\n\t"		    \
+		"4:"type##_lbu("$1", "0(%2)")"\n\t" \
+		"sll\t%0, 0x8\n\t"		    \
+		"or\t%0, $1\n\t"		    \
+		"li\t%1, 0\n"			    \
+		".set\tpop\n"			    \
+		"10:\n\t"			    \
+		".insn\n\t"			    \
+		".section\t.fixup,\"ax\"\n\t"	    \
+		"11:\tli\t%1, %3\n\t"		    \
+		"j\t10b\n\t"			    \
+		".previous\n\t"			    \
+		".section\t__ex_table,\"a\"\n\t"    \
+		STR(PTR_WD)"\t1b, 11b\n\t"	    \
+		STR(PTR_WD)"\t2b, 11b\n\t"	    \
+		STR(PTR_WD)"\t3b, 11b\n\t"	    \
+		STR(PTR_WD)"\t4b, 11b\n\t"	    \
+		".previous"			    \
+		: "=&r" (value), "=r" (res)	    \
+		: "r" (addr), "i" (-EFAULT));       \
+} while (0)
+
+#endif /* CONFIG_CPU_NO_LOAD_STORE_LR */
+
+
+#define  _LoadHWU(addr, value, res, type) \
+do {                                                \
+	__asm__ __volatile__ (                      \
+		".set\tnoat\n"                      \
+		"1:\t"type##_lbu("%0", "1(%2)")"\n" \
+		"2:\t"type##_lbu("$1", "0(%2)")"\n\t"\
+		"sll\t%0, 0x8\n\t"                  \
+		"or\t%0, $1\n\t"                    \
+		"li\t%1, 0\n"                       \
+		"3:\n\t"                            \
+		".insn\n\t"                         \
+		".set\tat\n\t"                      \
+		".section\t.fixup,\"ax\"\n\t"       \
+		"4:\tli\t%1, %3\n\t"                \
+		"j\t3b\n\t"                         \
+		".previous\n\t"                     \
+		".section\t__ex_table,\"a\"\n\t"    \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
+		".previous"                         \
+		: "=&r" (value), "=r" (res)         \
+		: "r" (addr), "i" (-EFAULT));       \
+} while (0)
+
+#ifndef CONFIG_CPU_NO_LOAD_STORE_LR
+#define  _LoadWU(addr, value, res, type)  \
+do {                                                \
+	__asm__ __volatile__ (                      \
+		"1:\t"type##_lwl("%0", "3(%2)")"\n" \
+		"2:\t"type##_lwr("%0", "(%2)")"\n\t"\
+		"dsll\t%0, %0, 32\n\t"              \
+		"dsrl\t%0, %0, 32\n\t"              \
+		"li\t%1, 0\n"                       \
+		"3:\n\t"                            \
+		".insn\n\t"                         \
+		"\t.section\t.fixup,\"ax\"\n\t"     \
+		"4:\tli\t%1, %3\n\t"                \
+		"j\t3b\n\t"                         \
+		".previous\n\t"                     \
+		".section\t__ex_table,\"a\"\n\t"    \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
+		".previous"                         \
+		: "=&r" (value), "=r" (res)         \
+		: "r" (addr), "i" (-EFAULT));       \
+} while (0)
+
+#define  _LoadDW(addr, value, res)  \
+do {                                                \
+	__asm__ __volatile__ (                      \
+		"1:\tldl\t%0, 7(%2)\n"              \
+		"2:\tldr\t%0, (%2)\n\t"             \
+		"li\t%1, 0\n"                       \
+		"3:\n\t"                            \
+		".insn\n\t"                         \
+		"\t.section\t.fixup,\"ax\"\n\t"     \
+		"4:\tli\t%1, %3\n\t"                \
+		"j\t3b\n\t"                         \
+		".previous\n\t"                     \
+		".section\t__ex_table,\"a\"\n\t"    \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
+		".previous"                         \
+		: "=&r" (value), "=r" (res)         \
+		: "r" (addr), "i" (-EFAULT));       \
+} while (0)
+
+#else /* CONFIG_CPU_NO_LOAD_STORE_LR */
+/* For CPUs without lwl and ldl instructions */
+#define  _LoadWU(addr, value, res, type) \
+do {                                                \
+	__asm__ __volatile__ (			    \
+		".set\tpush\n\t"		    \
+		".set\tnoat\n\t"		    \
+		"1:"type##_lbu("%0", "3(%2)")"\n\t" \
+		"2:"type##_lbu("$1", "2(%2)")"\n\t" \
+		"sll\t%0, 0x8\n\t"		    \
+		"or\t%0, $1\n\t"		    \
+		"3:"type##_lbu("$1", "1(%2)")"\n\t" \
+		"sll\t%0, 0x8\n\t"		    \
+		"or\t%0, $1\n\t"		    \
+		"4:"type##_lbu("$1", "0(%2)")"\n\t" \
+		"sll\t%0, 0x8\n\t"		    \
+		"or\t%0, $1\n\t"		    \
+		"li\t%1, 0\n"			    \
+		".set\tpop\n"			    \
+		"10:\n\t"			    \
+		".insn\n\t"			    \
+		".section\t.fixup,\"ax\"\n\t"	    \
+		"11:\tli\t%1, %3\n\t"		    \
+		"j\t10b\n\t"			    \
+		".previous\n\t"			    \
+		".section\t__ex_table,\"a\"\n\t"    \
+		STR(PTR_WD)"\t1b, 11b\n\t"	    \
+		STR(PTR_WD)"\t2b, 11b\n\t"	    \
+		STR(PTR_WD)"\t3b, 11b\n\t"	    \
+		STR(PTR_WD)"\t4b, 11b\n\t"	    \
+		".previous"			    \
+		: "=&r" (value), "=r" (res)	    \
+		: "r" (addr), "i" (-EFAULT));       \
+} while (0)
+
+#define  _LoadDW(addr, value, res)  \
+do {                                                \
+	__asm__ __volatile__ (			    \
+		".set\tpush\n\t"		    \
+		".set\tnoat\n\t"		    \
+		"1:lb\t%0, 7(%2)\n\t"		    \
+		"2:lbu\t$1, 6(%2)\n\t"		    \
+		"dsll\t%0, 0x8\n\t"		    \
+		"or\t%0, $1\n\t"		    \
+		"3:lbu\t$1, 5(%2)\n\t"		    \
+		"dsll\t%0, 0x8\n\t"		    \
+		"or\t%0, $1\n\t"		    \
+		"4:lbu\t$1, 4(%2)\n\t"		    \
+		"dsll\t%0, 0x8\n\t"		    \
+		"or\t%0, $1\n\t"		    \
+		"5:lbu\t$1, 3(%2)\n\t"		    \
+		"dsll\t%0, 0x8\n\t"		    \
+		"or\t%0, $1\n\t"		    \
+		"6:lbu\t$1, 2(%2)\n\t"		    \
+		"dsll\t%0, 0x8\n\t"		    \
+		"or\t%0, $1\n\t"		    \
+		"7:lbu\t$1, 1(%2)\n\t"		    \
+		"dsll\t%0, 0x8\n\t"		    \
+		"or\t%0, $1\n\t"		    \
+		"8:lbu\t$1, 0(%2)\n\t"		    \
+		"dsll\t%0, 0x8\n\t"		    \
+		"or\t%0, $1\n\t"		    \
+		"li\t%1, 0\n"			    \
+		".set\tpop\n\t"			    \
+		"10:\n\t"			    \
+		".insn\n\t"			    \
+		".section\t.fixup,\"ax\"\n\t"	    \
+		"11:\tli\t%1, %3\n\t"		    \
+		"j\t10b\n\t"			    \
+		".previous\n\t"			    \
+		".section\t__ex_table,\"a\"\n\t"    \
+		STR(PTR_WD)"\t1b, 11b\n\t"	    \
+		STR(PTR_WD)"\t2b, 11b\n\t"	    \
+		STR(PTR_WD)"\t3b, 11b\n\t"	    \
+		STR(PTR_WD)"\t4b, 11b\n\t"	    \
+		STR(PTR_WD)"\t5b, 11b\n\t"	    \
+		STR(PTR_WD)"\t6b, 11b\n\t"	    \
+		STR(PTR_WD)"\t7b, 11b\n\t"	    \
+		STR(PTR_WD)"\t8b, 11b\n\t"	    \
+		".previous"			    \
+		: "=&r" (value), "=r" (res)	    \
+		: "r" (addr), "i" (-EFAULT));       \
+} while (0)
+#endif /* CONFIG_CPU_NO_LOAD_STORE_LR */
+
+#define  _StoreHW(addr, value, res, type) \
+do {                                                 \
+	__asm__ __volatile__ (                      \
+		".set\tnoat\n"                      \
+		"1:\t"type##_sb("%1", "0(%2)")"\n"  \
+		"srl\t$1,%1, 0x8\n"                 \
+		"2:\t"type##_sb("$1", "1(%2)")"\n"  \
+		".set\tat\n\t"                      \
+		"li\t%0, 0\n"                       \
+		"3:\n\t"                            \
+		".insn\n\t"                         \
+		".section\t.fixup,\"ax\"\n\t"       \
+		"4:\tli\t%0, %3\n\t"                \
+		"j\t3b\n\t"                         \
+		".previous\n\t"                     \
+		".section\t__ex_table,\"a\"\n\t"    \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
+		".previous"                         \
+		: "=r" (res)                        \
+		: "r" (value), "r" (addr), "i" (-EFAULT));\
+} while (0)
+
+#ifndef CONFIG_CPU_NO_LOAD_STORE_LR
+#define  _StoreW(addr, value, res, type)  \
+do {                                                \
+	__asm__ __volatile__ (                      \
+		"1:\t"type##_swl("%1", "3(%2)")"\n" \
+		"2:\t"type##_swr("%1", "(%2)")"\n\t"\
+		"li\t%0, 0\n"                       \
+		"3:\n\t"                            \
+		".insn\n\t"                         \
+		".section\t.fixup,\"ax\"\n\t"       \
+		"4:\tli\t%0, %3\n\t"                \
+		"j\t3b\n\t"                         \
+		".previous\n\t"                     \
+		".section\t__ex_table,\"a\"\n\t"    \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
+		".previous"                         \
+		: "=r" (res)                                \
+		: "r" (value), "r" (addr), "i" (-EFAULT));  \
+} while (0)
+
+#define  _StoreDW(addr, value, res) \
+do {                                                \
+	__asm__ __volatile__ (                      \
+		"1:\tsdl\t%1, 7(%2)\n"              \
+		"2:\tsdr\t%1, (%2)\n\t"             \
+		"li\t%0, 0\n"                       \
+		"3:\n\t"                            \
+		".insn\n\t"                         \
+		".section\t.fixup,\"ax\"\n\t"       \
+		"4:\tli\t%0, %3\n\t"                \
+		"j\t3b\n\t"                         \
+		".previous\n\t"                     \
+		".section\t__ex_table,\"a\"\n\t"    \
+		STR(PTR_WD)"\t1b, 4b\n\t"           \
+		STR(PTR_WD)"\t2b, 4b\n\t"           \
+		".previous"                         \
+		: "=r" (res)                                \
+		: "r" (value), "r" (addr), "i" (-EFAULT));  \
+} while (0)
+
+#else /* CONFIG_CPU_NO_LOAD_STORE_LR */
+/* For CPUs without swl and sdl instructions */
+#define  _StoreW(addr, value, res, type)  \
+do {                                                \
+	__asm__ __volatile__ (                      \
+		".set\tpush\n\t"		    \
+		".set\tnoat\n\t"		    \
+		"1:"type##_sb("%1", "0(%2)")"\n\t"  \
+		"srl\t$1, %1, 0x8\n\t"		    \
+		"2:"type##_sb("$1", "1(%2)")"\n\t"  \
+		"srl\t$1, $1,  0x8\n\t"		    \
+		"3:"type##_sb("$1", "2(%2)")"\n\t"  \
+		"srl\t$1, $1, 0x8\n\t"		    \
+		"4:"type##_sb("$1", "3(%2)")"\n\t"  \
+		".set\tpop\n\t"			    \
+		"li\t%0, 0\n"			    \
+		"10:\n\t"			    \
+		".insn\n\t"			    \
+		".section\t.fixup,\"ax\"\n\t"	    \
+		"11:\tli\t%0, %3\n\t"		    \
+		"j\t10b\n\t"			    \
+		".previous\n\t"			    \
+		".section\t__ex_table,\"a\"\n\t"    \
+		STR(PTR_WD)"\t1b, 11b\n\t"	    \
+		STR(PTR_WD)"\t2b, 11b\n\t"	    \
+		STR(PTR_WD)"\t3b, 11b\n\t"	    \
+		STR(PTR_WD)"\t4b, 11b\n\t"	    \
+		".previous"			    \
+		: "=&r" (res)				    \
+		: "r" (value), "r" (addr), "i" (-EFAULT)    \
+		: "memory");                                \
+} while (0)
+
+#define  _StoreDW(addr, value, res) \
+do {                                                \
+	__asm__ __volatile__ (                      \
+		".set\tpush\n\t"		    \
+		".set\tnoat\n\t"		    \
+		"1:sb\t%1, 0(%2)\n\t"		    \
+		"dsrl\t$1, %1, 0x8\n\t"		    \
+		"2:sb\t$1, 1(%2)\n\t"		    \
+		"dsrl\t$1, $1, 0x8\n\t"		    \
+		"3:sb\t$1, 2(%2)\n\t"		    \
+		"dsrl\t$1, $1, 0x8\n\t"		    \
+		"4:sb\t$1, 3(%2)\n\t"		    \
+		"dsrl\t$1, $1, 0x8\n\t"		    \
+		"5:sb\t$1, 4(%2)\n\t"		    \
+		"dsrl\t$1, $1, 0x8\n\t"		    \
+		"6:sb\t$1, 5(%2)\n\t"		    \
+		"dsrl\t$1, $1, 0x8\n\t"		    \
+		"7:sb\t$1, 6(%2)\n\t"		    \
+		"dsrl\t$1, $1, 0x8\n\t"		    \
+		"8:sb\t$1, 7(%2)\n\t"		    \
+		"dsrl\t$1, $1, 0x8\n\t"		    \
+		".set\tpop\n\t"			    \
+		"li\t%0, 0\n"			    \
+		"10:\n\t"			    \
+		".insn\n\t"			    \
+		".section\t.fixup,\"ax\"\n\t"	    \
+		"11:\tli\t%0, %3\n\t"		    \
+		"j\t10b\n\t"			    \
+		".previous\n\t"			    \
+		".section\t__ex_table,\"a\"\n\t"    \
+		STR(PTR_WD)"\t1b, 11b\n\t"	    \
+		STR(PTR_WD)"\t2b, 11b\n\t"	    \
+		STR(PTR_WD)"\t3b, 11b\n\t"	    \
+		STR(PTR_WD)"\t4b, 11b\n\t"	    \
+		STR(PTR_WD)"\t5b, 11b\n\t"	    \
+		STR(PTR_WD)"\t6b, 11b\n\t"	    \
+		STR(PTR_WD)"\t7b, 11b\n\t"	    \
+		STR(PTR_WD)"\t8b, 11b\n\t"	    \
+		".previous"			    \
+		: "=&r" (res)				    \
+		: "r" (value), "r" (addr), "i" (-EFAULT)    \
+		: "memory");                                \
+} while (0)
+
+#endif /* CONFIG_CPU_NO_LOAD_STORE_LR */
+#endif
+
+#define LoadHWU(addr, value, res)	_LoadHWU(addr, value, res, kernel)
+#define LoadHWUE(addr, value, res)	_LoadHWU(addr, value, res, user)
+#define LoadWU(addr, value, res)	_LoadWU(addr, value, res, kernel)
+#define LoadWUE(addr, value, res)	_LoadWU(addr, value, res, user)
+#define LoadHW(addr, value, res)	_LoadHW(addr, value, res, kernel)
+#define LoadHWE(addr, value, res)	_LoadHW(addr, value, res, user)
+#define LoadW(addr, value, res)		_LoadW(addr, value, res, kernel)
+#define LoadWE(addr, value, res)	_LoadW(addr, value, res, user)
+#define LoadDW(addr, value, res)	_LoadDW(addr, value, res)
+
+#define StoreHW(addr, value, res)	_StoreHW(addr, value, res, kernel)
+#define StoreHWE(addr, value, res)	_StoreHW(addr, value, res, user)
+#define StoreW(addr, value, res)	_StoreW(addr, value, res, kernel)
+#define StoreWE(addr, value, res)	_StoreW(addr, value, res, user)
+#define StoreDW(addr, value, res)	_StoreDW(addr, value, res)
+
+#endif /* _ASM_MIPS_UNALIGNED_EMUL_H */
diff --git a/arch/mips/include/asm/unistd.h b/arch/mips/include/asm/unistd.h
new file mode 100644
index 000000000..25a5253db
--- /dev/null
+++ b/arch/mips/include/asm/unistd.h
@@ -0,0 +1,68 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995, 96, 97, 98, 99, 2000 by Ralf Baechle
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ *
+ * Changed system calls macros _syscall5 - _syscall7 to push args 5 to 7 onto
+ * the stack. Robin Farine for ACN S.A, Copyright (C) 1996 by ACN S.A
+ */
+#ifndef _ASM_UNISTD_H
+#define _ASM_UNISTD_H
+
+#include <uapi/asm/unistd.h>
+#include <asm/unistd_nr_n32.h>
+#include <asm/unistd_nr_n64.h>
+#include <asm/unistd_nr_o32.h>
+
+#define __NR_N32_Linux	6000
+#define __NR_64_Linux	5000
+#define __NR_O32_Linux	4000
+
+#ifdef CONFIG_MIPS32_N32
+#define NR_syscalls  (__NR_N32_Linux + __NR_N32_Linux_syscalls)
+#elif defined(CONFIG_64BIT)
+#define NR_syscalls  (__NR_64_Linux + __NR_64_Linux_syscalls)
+#else
+#define NR_syscalls  (__NR_O32_Linux + __NR_O32_Linux_syscalls)
+#endif
+
+#ifndef __ASSEMBLY__
+
+#define __ARCH_WANT_NEW_STAT
+#define __ARCH_WANT_OLD_READDIR
+#define __ARCH_WANT_SYS_ALARM
+#define __ARCH_WANT_SYS_GETHOSTNAME
+#define __ARCH_WANT_SYS_IPC
+#define __ARCH_WANT_SYS_PAUSE
+#define __ARCH_WANT_SYS_UTIME
+#define __ARCH_WANT_SYS_UTIME32
+#define __ARCH_WANT_SYS_WAITPID
+#define __ARCH_WANT_SYS_SOCKETCALL
+#define __ARCH_WANT_SYS_GETPGRP
+#define __ARCH_WANT_SYS_NICE
+#define __ARCH_WANT_SYS_OLD_UNAME
+#define __ARCH_WANT_SYS_OLDUMOUNT
+#define __ARCH_WANT_SYS_SIGPENDING
+#define __ARCH_WANT_SYS_SIGPROCMASK
+# ifdef CONFIG_32BIT
+#  define __ARCH_WANT_STAT64
+#  define __ARCH_WANT_SYS_TIME32
+# else
+#  define __ARCH_WANT_COMPAT_STAT
+# endif
+# ifdef CONFIG_MIPS32_O32
+#  define __ARCH_WANT_SYS_TIME32
+# endif
+#define __ARCH_WANT_SYS_FORK
+#define __ARCH_WANT_SYS_CLONE
+#define __ARCH_WANT_SYS_CLONE3
+
+/* whitelists for checksyscalls */
+#define __IGNORE_fadvise64_64
+
+#endif /* !__ASSEMBLY__ */
+
+#endif /* _ASM_UNISTD_H */
diff --git a/arch/mips/include/asm/unroll.h b/arch/mips/include/asm/unroll.h
new file mode 100644
index 000000000..6f4ac854b
--- /dev/null
+++ b/arch/mips/include/asm/unroll.h
@@ -0,0 +1,75 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+#ifndef __ASM_UNROLL_H__
+#define __ASM_UNROLL_H__
+
+/*
+ * Explicitly unroll a loop, for use in cases where doing so is performance
+ * critical.
+ *
+ * Ideally we'd rely upon the compiler to provide this but there's no commonly
+ * available means to do so. For example GCC's "#pragma GCC unroll"
+ * functionality would be ideal but is only available from GCC 8 onwards. Using
+ * -funroll-loops is an option but GCC tends to make poor choices when
+ * compiling our string functions. -funroll-all-loops leads to massive code
+ * bloat, even if only applied to the string functions.
+ */
+#define unroll(times, fn, ...) do {				\
+	extern void bad_unroll(void)				\
+		__compiletime_error("Unsupported unroll");	\
+								\
+	/*							\
+	 * We can't unroll if the number of iterations isn't	\
+	 * compile-time constant. Unfortunately clang versions	\
+	 * up until 8.0 tend to miss obvious constants & cause	\
+	 * this check to fail, even though they go on to	\
+	 * generate reasonable code for the switch statement,	\
+	 * so we skip the sanity check for those compilers.	\
+	 */							\
+	BUILD_BUG_ON(!__builtin_constant_p(times));		\
+								\
+	switch (times) {					\
+	case 32: fn(__VA_ARGS__); fallthrough;			\
+	case 31: fn(__VA_ARGS__); fallthrough;			\
+	case 30: fn(__VA_ARGS__); fallthrough;			\
+	case 29: fn(__VA_ARGS__); fallthrough;			\
+	case 28: fn(__VA_ARGS__); fallthrough;			\
+	case 27: fn(__VA_ARGS__); fallthrough;			\
+	case 26: fn(__VA_ARGS__); fallthrough;			\
+	case 25: fn(__VA_ARGS__); fallthrough;			\
+	case 24: fn(__VA_ARGS__); fallthrough;			\
+	case 23: fn(__VA_ARGS__); fallthrough;			\
+	case 22: fn(__VA_ARGS__); fallthrough;			\
+	case 21: fn(__VA_ARGS__); fallthrough;			\
+	case 20: fn(__VA_ARGS__); fallthrough;			\
+	case 19: fn(__VA_ARGS__); fallthrough;			\
+	case 18: fn(__VA_ARGS__); fallthrough;			\
+	case 17: fn(__VA_ARGS__); fallthrough;			\
+	case 16: fn(__VA_ARGS__); fallthrough;			\
+	case 15: fn(__VA_ARGS__); fallthrough;			\
+	case 14: fn(__VA_ARGS__); fallthrough;			\
+	case 13: fn(__VA_ARGS__); fallthrough;			\
+	case 12: fn(__VA_ARGS__); fallthrough;			\
+	case 11: fn(__VA_ARGS__); fallthrough;			\
+	case 10: fn(__VA_ARGS__); fallthrough;			\
+	case 9: fn(__VA_ARGS__); fallthrough;			\
+	case 8: fn(__VA_ARGS__); fallthrough;			\
+	case 7: fn(__VA_ARGS__); fallthrough;			\
+	case 6: fn(__VA_ARGS__); fallthrough;			\
+	case 5: fn(__VA_ARGS__); fallthrough;			\
+	case 4: fn(__VA_ARGS__); fallthrough;			\
+	case 3: fn(__VA_ARGS__); fallthrough;			\
+	case 2: fn(__VA_ARGS__); fallthrough;			\
+	case 1: fn(__VA_ARGS__); fallthrough;			\
+	case 0: break;						\
+								\
+	default:						\
+		/*						\
+		 * Either the iteration count is unreasonable	\
+		 * or we need to add more cases above.		\
+		 */						\
+		bad_unroll();					\
+		break;						\
+	}							\
+} while (0)
+
+#endif /* __ASM_UNROLL_H__ */
diff --git a/arch/mips/include/asm/uprobes.h b/arch/mips/include/asm/uprobes.h
new file mode 100644
index 000000000..b86d1ae07
--- /dev/null
+++ b/arch/mips/include/asm/uprobes.h
@@ -0,0 +1,45 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#ifndef __ASM_UPROBES_H
+#define __ASM_UPROBES_H
+
+#include <linux/notifier.h>
+#include <linux/types.h>
+
+#include <asm/break.h>
+#include <asm/inst.h>
+
+/*
+ * We want this to be defined as union mips_instruction but that makes the
+ * generic code blow up.
+ */
+typedef u32 uprobe_opcode_t;
+
+/*
+ * Classic MIPS (note this implementation doesn't consider microMIPS yet)
+ * instructions are always 4 bytes but in order to deal with branches and
+ * their delay slots, we treat instructions as having 8 bytes maximum.
+ */
+#define MAX_UINSN_BYTES			8
+#define UPROBE_XOL_SLOT_BYTES		128	/* Max. cache line size */
+
+#define UPROBE_BRK_UPROBE		0x000d000d	/* break 13 */
+#define UPROBE_BRK_UPROBE_XOL		0x000e000d	/* break 14 */
+
+#define UPROBE_SWBP_INSN		UPROBE_BRK_UPROBE
+#define UPROBE_SWBP_INSN_SIZE		4
+
+struct arch_uprobe {
+	unsigned long	resume_epc;
+	u32	insn[2];
+	u32	ixol[2];
+};
+
+struct arch_uprobe_task {
+	unsigned long saved_trap_nr;
+};
+
+#endif /* __ASM_UPROBES_H */
diff --git a/arch/mips/include/asm/vdso.h b/arch/mips/include/asm/vdso.h
new file mode 100644
index 000000000..cc7b51612
--- /dev/null
+++ b/arch/mips/include/asm/vdso.h
@@ -0,0 +1,58 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2015 Imagination Technologies
+ * Author: Alex Smith <alex.smith@imgtec.com>
+ */
+
+#ifndef __ASM_VDSO_H
+#define __ASM_VDSO_H
+
+#include <linux/mm_types.h>
+#include <vdso/datapage.h>
+
+#include <asm/barrier.h>
+
+/**
+ * struct mips_vdso_image - Details of a VDSO image.
+ * @data: Pointer to VDSO image data (page-aligned).
+ * @size: Size of the VDSO image data (page-aligned).
+ * @off_sigreturn: Offset of the sigreturn() trampoline.
+ * @off_rt_sigreturn: Offset of the rt_sigreturn() trampoline.
+ * @mapping: Special mapping structure.
+ *
+ * This structure contains details of a VDSO image, including the image data
+ * and offsets of certain symbols required by the kernel. It is generated as
+ * part of the VDSO build process, aside from the mapping page array, which is
+ * populated at runtime.
+ */
+struct mips_vdso_image {
+	void *data;
+	unsigned long size;
+
+	unsigned long off_sigreturn;
+	unsigned long off_rt_sigreturn;
+
+	struct vm_special_mapping mapping;
+};
+
+/*
+ * The following structures are auto-generated as part of the build for each
+ * ABI by genvdso, see arch/mips/vdso/Makefile.
+ */
+
+extern struct mips_vdso_image vdso_image;
+
+#ifdef CONFIG_MIPS32_O32
+extern struct mips_vdso_image vdso_image_o32;
+#endif
+
+#ifdef CONFIG_MIPS32_N32
+extern struct mips_vdso_image vdso_image_n32;
+#endif
+
+union mips_vdso_data {
+	struct vdso_data data[CS_BASES];
+	u8 page[PAGE_SIZE];
+};
+
+#endif /* __ASM_VDSO_H */
diff --git a/arch/mips/include/asm/vdso/clocksource.h b/arch/mips/include/asm/vdso/clocksource.h
new file mode 100644
index 000000000..510e1671d
--- /dev/null
+++ b/arch/mips/include/asm/vdso/clocksource.h
@@ -0,0 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+#ifndef __ASM_VDSOCLOCKSOURCE_H
+#define __ASM_VDSOCLOCKSOURCE_H
+
+#define VDSO_ARCH_CLOCKMODES	\
+	VDSO_CLOCKMODE_R4K,	\
+	VDSO_CLOCKMODE_GIC
+
+#endif /* __ASM_VDSOCLOCKSOURCE_H */
diff --git a/arch/mips/include/asm/vdso/gettimeofday.h b/arch/mips/include/asm/vdso/gettimeofday.h
new file mode 100644
index 000000000..44a45f3fa
--- /dev/null
+++ b/arch/mips/include/asm/vdso/gettimeofday.h
@@ -0,0 +1,219 @@
+/*
+ * Copyright (C) 2018 ARM Limited
+ * Copyright (C) 2015 Imagination Technologies
+ * Author: Alex Smith <alex.smith@imgtec.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+#ifndef __ASM_VDSO_GETTIMEOFDAY_H
+#define __ASM_VDSO_GETTIMEOFDAY_H
+
+#ifndef __ASSEMBLY__
+
+#include <asm/vdso/vdso.h>
+#include <asm/clocksource.h>
+#include <asm/unistd.h>
+#include <asm/vdso.h>
+
+#define VDSO_HAS_CLOCK_GETRES		1
+
+#if MIPS_ISA_REV < 6
+#define VDSO_SYSCALL_CLOBBERS "hi", "lo",
+#else
+#define VDSO_SYSCALL_CLOBBERS
+#endif
+
+static __always_inline long gettimeofday_fallback(
+				struct __kernel_old_timeval *_tv,
+				struct timezone *_tz)
+{
+	register struct timezone *tz asm("a1") = _tz;
+	register struct __kernel_old_timeval *tv asm("a0") = _tv;
+	register long ret asm("v0");
+	register long nr asm("v0") = __NR_gettimeofday;
+	register long error asm("a3");
+
+	asm volatile(
+	"       syscall\n"
+	: "=r" (ret), "=r" (error)
+	: "r" (tv), "r" (tz), "r" (nr)
+	: "$1", "$3", "$8", "$9", "$10", "$11", "$12", "$13",
+	  "$14", "$15", "$24", "$25",
+	  VDSO_SYSCALL_CLOBBERS
+	  "memory");
+
+	return error ? -ret : ret;
+}
+
+static __always_inline long clock_gettime_fallback(
+					clockid_t _clkid,
+					struct __kernel_timespec *_ts)
+{
+	register struct __kernel_timespec *ts asm("a1") = _ts;
+	register clockid_t clkid asm("a0") = _clkid;
+	register long ret asm("v0");
+#if _MIPS_SIM == _MIPS_SIM_ABI64
+	register long nr asm("v0") = __NR_clock_gettime;
+#else
+	register long nr asm("v0") = __NR_clock_gettime64;
+#endif
+	register long error asm("a3");
+
+	asm volatile(
+	"       syscall\n"
+	: "=r" (ret), "=r" (error)
+	: "r" (clkid), "r" (ts), "r" (nr)
+	: "$1", "$3", "$8", "$9", "$10", "$11", "$12", "$13",
+	  "$14", "$15", "$24", "$25",
+	  VDSO_SYSCALL_CLOBBERS
+	  "memory");
+
+	return error ? -ret : ret;
+}
+
+static __always_inline int clock_getres_fallback(
+					clockid_t _clkid,
+					struct __kernel_timespec *_ts)
+{
+	register struct __kernel_timespec *ts asm("a1") = _ts;
+	register clockid_t clkid asm("a0") = _clkid;
+	register long ret asm("v0");
+#if _MIPS_SIM == _MIPS_SIM_ABI64
+	register long nr asm("v0") = __NR_clock_getres;
+#else
+	register long nr asm("v0") = __NR_clock_getres_time64;
+#endif
+	register long error asm("a3");
+
+	asm volatile(
+	"       syscall\n"
+	: "=r" (ret), "=r" (error)
+	: "r" (clkid), "r" (ts), "r" (nr)
+	: "$1", "$3", "$8", "$9", "$10", "$11", "$12", "$13",
+	  "$14", "$15", "$24", "$25",
+	  VDSO_SYSCALL_CLOBBERS
+	  "memory");
+
+	return error ? -ret : ret;
+}
+
+#if _MIPS_SIM != _MIPS_SIM_ABI64
+
+static __always_inline long clock_gettime32_fallback(
+					clockid_t _clkid,
+					struct old_timespec32 *_ts)
+{
+	register struct old_timespec32 *ts asm("a1") = _ts;
+	register clockid_t clkid asm("a0") = _clkid;
+	register long ret asm("v0");
+	register long nr asm("v0") = __NR_clock_gettime;
+	register long error asm("a3");
+
+	asm volatile(
+	"       syscall\n"
+	: "=r" (ret), "=r" (error)
+	: "r" (clkid), "r" (ts), "r" (nr)
+	: "$1", "$3", "$8", "$9", "$10", "$11", "$12", "$13",
+	  "$14", "$15", "$24", "$25",
+	  VDSO_SYSCALL_CLOBBERS
+	  "memory");
+
+	return error ? -ret : ret;
+}
+
+static __always_inline int clock_getres32_fallback(
+					clockid_t _clkid,
+					struct old_timespec32 *_ts)
+{
+	register struct old_timespec32 *ts asm("a1") = _ts;
+	register clockid_t clkid asm("a0") = _clkid;
+	register long ret asm("v0");
+	register long nr asm("v0") = __NR_clock_getres;
+	register long error asm("a3");
+
+	asm volatile(
+	"       syscall\n"
+	: "=r" (ret), "=r" (error)
+	: "r" (clkid), "r" (ts), "r" (nr)
+	: "$1", "$3", "$8", "$9", "$10", "$11", "$12", "$13",
+	  "$14", "$15", "$24", "$25",
+	  VDSO_SYSCALL_CLOBBERS
+	  "memory");
+
+	return error ? -ret : ret;
+}
+#endif
+
+#ifdef CONFIG_CSRC_R4K
+
+static __always_inline u64 read_r4k_count(void)
+{
+	unsigned int count;
+
+	__asm__ __volatile__(
+	"	.set push\n"
+	"	.set mips32r2\n"
+	"	rdhwr	%0, $2\n"
+	"	.set pop\n"
+	: "=r" (count));
+
+	return count;
+}
+
+#endif
+
+#ifdef CONFIG_CLKSRC_MIPS_GIC
+
+static __always_inline u64 read_gic_count(const struct vdso_data *data)
+{
+	void __iomem *gic = get_gic(data);
+	u32 hi, hi2, lo;
+
+	do {
+		hi = __raw_readl(gic + sizeof(lo));
+		lo = __raw_readl(gic);
+		hi2 = __raw_readl(gic + sizeof(lo));
+	} while (hi2 != hi);
+
+	return (((u64)hi) << 32) + lo;
+}
+
+#endif
+
+static __always_inline u64 __arch_get_hw_counter(s32 clock_mode,
+						 const struct vdso_data *vd)
+{
+#ifdef CONFIG_CSRC_R4K
+	if (clock_mode == VDSO_CLOCKMODE_R4K)
+		return read_r4k_count();
+#endif
+#ifdef CONFIG_CLKSRC_MIPS_GIC
+	if (clock_mode == VDSO_CLOCKMODE_GIC)
+		return read_gic_count(vd);
+#endif
+	/*
+	 * Core checks mode already. So this raced against a concurrent
+	 * update. Return something. Core will do another round see the
+	 * change and fallback to syscall.
+	 */
+	return 0;
+}
+
+static inline bool mips_vdso_hres_capable(void)
+{
+	return IS_ENABLED(CONFIG_CSRC_R4K) ||
+	       IS_ENABLED(CONFIG_CLKSRC_MIPS_GIC);
+}
+#define __arch_vdso_hres_capable mips_vdso_hres_capable
+
+static __always_inline const struct vdso_data *__arch_get_vdso_data(void)
+{
+	return get_vdso_data();
+}
+
+#endif /* !__ASSEMBLY__ */
+
+#endif /* __ASM_VDSO_GETTIMEOFDAY_H */
diff --git a/arch/mips/include/asm/vdso/processor.h b/arch/mips/include/asm/vdso/processor.h
new file mode 100644
index 000000000..511c95d73
--- /dev/null
+++ b/arch/mips/include/asm/vdso/processor.h
@@ -0,0 +1,27 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (C) 2020 ARM Ltd.
+ */
+#ifndef __ASM_VDSO_PROCESSOR_H
+#define __ASM_VDSO_PROCESSOR_H
+
+#ifndef __ASSEMBLY__
+
+#ifdef CONFIG_CPU_LOONGSON64
+/*
+ * Loongson-3's SFB (Store-Fill-Buffer) may buffer writes indefinitely when a
+ * tight read loop is executed, because reads take priority over writes & the
+ * hardware (incorrectly) doesn't ensure that writes will eventually occur.
+ *
+ * Since spin loops of any kind should have a cpu_relax() in them, force an SFB
+ * flush from cpu_relax() such that any pending writes will become visible as
+ * expected.
+ */
+#define cpu_relax()	smp_mb()
+#else
+#define cpu_relax()	barrier()
+#endif
+
+#endif /* __ASSEMBLY__ */
+
+#endif /* __ASM_VDSO_PROCESSOR_H */
diff --git a/arch/mips/include/asm/vdso/vdso.h b/arch/mips/include/asm/vdso/vdso.h
new file mode 100644
index 000000000..a327ca212
--- /dev/null
+++ b/arch/mips/include/asm/vdso/vdso.h
@@ -0,0 +1,75 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2015 Imagination Technologies
+ * Author: Alex Smith <alex.smith@imgtec.com>
+ */
+
+#include <asm/sgidefs.h>
+
+#ifndef __ASSEMBLY__
+
+#include <asm/asm.h>
+#include <asm/page.h>
+#include <asm/vdso.h>
+
+static inline unsigned long get_vdso_base(void)
+{
+	unsigned long addr;
+
+	/*
+	 * We can't use cpu_has_mips_r6 since it needs the cpu_data[]
+	 * kernel symbol.
+	 */
+#ifdef CONFIG_CPU_MIPSR6
+	/*
+	 * lapc <symbol> is an alias to addiupc reg, <symbol> - .
+	 *
+	 * We can't use addiupc because there is no label-label
+	 * support for the addiupc reloc
+	 */
+	__asm__("lapc	%0, _start			\n"
+		: "=r" (addr) : :);
+#else
+	/*
+	 * Get the base load address of the VDSO. We have to avoid generating
+	 * relocations and references to the GOT because ld.so does not peform
+	 * relocations on the VDSO. We use the current offset from the VDSO base
+	 * and perform a PC-relative branch which gives the absolute address in
+	 * ra, and take the difference. The assembler chokes on
+	 * "li %0, _start - .", so embed the offset as a word and branch over
+	 * it.
+	 *
+	 */
+
+	__asm__(
+	"	.set push				\n"
+	"	.set noreorder				\n"
+	"	bal	1f				\n"
+	"	 nop					\n"
+	"	.word	_start - .			\n"
+	"1:	lw	%0, 0($31)			\n"
+	"	" STR(PTR_ADDU) " %0, $31, %0		\n"
+	"	.set pop				\n"
+	: "=r" (addr)
+	:
+	: "$31");
+#endif /* CONFIG_CPU_MIPSR6 */
+
+	return addr;
+}
+
+static inline const struct vdso_data *get_vdso_data(void)
+{
+	return (const struct vdso_data *)(get_vdso_base() - PAGE_SIZE);
+}
+
+#ifdef CONFIG_CLKSRC_MIPS_GIC
+
+static inline void __iomem *get_gic(const struct vdso_data *data)
+{
+	return (void __iomem *)((unsigned long)data & PAGE_MASK) - PAGE_SIZE;
+}
+
+#endif /* CONFIG_CLKSRC_MIPS_GIC */
+
+#endif /* __ASSEMBLY__ */
diff --git a/arch/mips/include/asm/vdso/vsyscall.h b/arch/mips/include/asm/vdso/vsyscall.h
new file mode 100644
index 000000000..47168aaf1
--- /dev/null
+++ b/arch/mips/include/asm/vdso/vsyscall.h
@@ -0,0 +1,27 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_VDSO_VSYSCALL_H
+#define __ASM_VDSO_VSYSCALL_H
+
+#ifndef __ASSEMBLY__
+
+#include <linux/timekeeper_internal.h>
+#include <vdso/datapage.h>
+
+extern struct vdso_data *vdso_data;
+
+/*
+ * Update the vDSO data page to keep in sync with kernel timekeeping.
+ */
+static __always_inline
+struct vdso_data *__mips_get_k_vdso_data(void)
+{
+	return vdso_data;
+}
+#define __arch_get_k_vdso_data __mips_get_k_vdso_data
+
+/* The asm-generic header needs to be included after the definitions above */
+#include <asm-generic/vdso/vsyscall.h>
+
+#endif /* !__ASSEMBLY__ */
+
+#endif /* __ASM_VDSO_VSYSCALL_H */
diff --git a/arch/mips/include/asm/vermagic.h b/arch/mips/include/asm/vermagic.h
new file mode 100644
index 000000000..7645f77c8
--- /dev/null
+++ b/arch/mips/include/asm/vermagic.h
@@ -0,0 +1,66 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _ASM_VERMAGIC_H
+#define _ASM_VERMAGIC_H
+
+#ifdef CONFIG_CPU_BMIPS
+#define MODULE_PROC_FAMILY "BMIPS "
+#elif defined CONFIG_CPU_MIPS32_R1
+#define MODULE_PROC_FAMILY "MIPS32_R1 "
+#elif defined CONFIG_CPU_MIPS32_R2
+#define MODULE_PROC_FAMILY "MIPS32_R2 "
+#elif defined CONFIG_CPU_MIPS32_R5
+#define MODULE_PROC_FAMILY "MIPS32_R5 "
+#elif defined CONFIG_CPU_MIPS32_R6
+#define MODULE_PROC_FAMILY "MIPS32_R6 "
+#elif defined CONFIG_CPU_MIPS64_R1
+#define MODULE_PROC_FAMILY "MIPS64_R1 "
+#elif defined CONFIG_CPU_MIPS64_R2
+#define MODULE_PROC_FAMILY "MIPS64_R2 "
+#elif defined CONFIG_CPU_MIPS64_R5
+#define MODULE_PROC_FAMILY "MIPS64_R5 "
+#elif defined CONFIG_CPU_MIPS64_R6
+#define MODULE_PROC_FAMILY "MIPS64_R6 "
+#elif defined CONFIG_CPU_R3000
+#define MODULE_PROC_FAMILY "R3000 "
+#elif defined CONFIG_CPU_R4300
+#define MODULE_PROC_FAMILY "R4300 "
+#elif defined CONFIG_CPU_R4X00
+#define MODULE_PROC_FAMILY "R4X00 "
+#elif defined CONFIG_CPU_TX49XX
+#define MODULE_PROC_FAMILY "TX49XX "
+#elif defined CONFIG_CPU_R5000
+#define MODULE_PROC_FAMILY "R5000 "
+#elif defined CONFIG_CPU_R5500
+#define MODULE_PROC_FAMILY "R5500 "
+#elif defined CONFIG_CPU_NEVADA
+#define MODULE_PROC_FAMILY "NEVADA "
+#elif defined CONFIG_CPU_R10000
+#define MODULE_PROC_FAMILY "R10000 "
+#elif defined CONFIG_CPU_RM7000
+#define MODULE_PROC_FAMILY "RM7000 "
+#elif defined CONFIG_CPU_SB1
+#define MODULE_PROC_FAMILY "SB1 "
+#elif defined CONFIG_CPU_LOONGSON32
+#define MODULE_PROC_FAMILY "LOONGSON32 "
+#elif defined CONFIG_CPU_LOONGSON2EF
+#define MODULE_PROC_FAMILY "LOONGSON2EF "
+#elif defined CONFIG_CPU_LOONGSON64
+#define MODULE_PROC_FAMILY "LOONGSON64 "
+#elif defined CONFIG_CPU_CAVIUM_OCTEON
+#define MODULE_PROC_FAMILY "OCTEON "
+#elif defined CONFIG_CPU_P5600
+#define MODULE_PROC_FAMILY "P5600 "
+#else
+#error MODULE_PROC_FAMILY undefined for your processor configuration
+#endif
+
+#ifdef CONFIG_32BIT
+#define MODULE_KERNEL_TYPE "32BIT "
+#elif defined CONFIG_64BIT
+#define MODULE_KERNEL_TYPE "64BIT "
+#endif
+
+#define MODULE_ARCH_VERMAGIC \
+	MODULE_PROC_FAMILY MODULE_KERNEL_TYPE
+
+#endif /* _ASM_VERMAGIC_H */
diff --git a/arch/mips/include/asm/vga.h b/arch/mips/include/asm/vga.h
new file mode 100644
index 000000000..0136e0366
--- /dev/null
+++ b/arch/mips/include/asm/vga.h
@@ -0,0 +1,56 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ *	Access to VGA videoram
+ *
+ *	(c) 1998 Martin Mares <mj@ucw.cz>
+ */
+#ifndef _ASM_VGA_H
+#define _ASM_VGA_H
+
+#include <linux/string.h>
+#include <asm/addrspace.h>
+#include <asm/byteorder.h>
+
+/*
+ *	On the PC, we can just recalculate addresses and then
+ *	access the videoram directly without any black magic.
+ */
+
+#define VGA_MAP_MEM(x, s)	CKSEG1ADDR(0x10000000L + (unsigned long)(x))
+
+#define vga_readb(x)	(*(x))
+#define vga_writeb(x, y)	(*(y) = (x))
+
+#define VT_BUF_HAVE_RW
+/*
+ *  These are only needed for supporting VGA or MDA text mode, which use little
+ *  endian byte ordering.
+ *  In other cases, we can optimize by using native byte ordering and
+ *  <linux/vt_buffer.h> has already done the right job for us.
+ */
+
+#undef scr_writew
+#undef scr_readw
+
+static inline void scr_writew(u16 val, volatile u16 *addr)
+{
+	*addr = cpu_to_le16(val);
+}
+
+static inline u16 scr_readw(volatile const u16 *addr)
+{
+	return le16_to_cpu(*addr);
+}
+
+static inline void scr_memsetw(u16 *s, u16 v, unsigned int count)
+{
+	memset16(s, cpu_to_le16(v), count / 2);
+}
+
+#define scr_memcpyw(d, s, c) memcpy(d, s, c)
+#define scr_memmovew(d, s, c) memmove(d, s, c)
+#define VT_BUF_HAVE_MEMCPYW
+#define VT_BUF_HAVE_MEMMOVEW
+#define VT_BUF_HAVE_MEMSETW
+
+#endif /* _ASM_VGA_H */
diff --git a/arch/mips/include/asm/vmalloc.h b/arch/mips/include/asm/vmalloc.h
new file mode 100644
index 000000000..25dc09b25
--- /dev/null
+++ b/arch/mips/include/asm/vmalloc.h
@@ -0,0 +1,4 @@
+#ifndef _ASM_MIPS_VMALLOC_H
+#define _ASM_MIPS_VMALLOC_H
+
+#endif /* _ASM_MIPS_VMALLOC_H */
diff --git a/arch/mips/include/asm/vpe.h b/arch/mips/include/asm/vpe.h
new file mode 100644
index 000000000..baa949a74
--- /dev/null
+++ b/arch/mips/include/asm/vpe.h
@@ -0,0 +1,127 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2005 MIPS Technologies, Inc.  All rights reserved.
+ * Copyright (C) 2013 Imagination Technologies Ltd.
+ */
+#ifndef _ASM_VPE_H
+#define _ASM_VPE_H
+
+#include <linux/init.h>
+#include <linux/list.h>
+#include <linux/smp.h>
+#include <linux/spinlock.h>
+
+#define VPE_MODULE_NAME "vpe"
+#define VPE_MODULE_MINOR 1
+
+/* grab the likely amount of memory we will need. */
+#ifdef CONFIG_MIPS_VPE_LOADER_TOM
+#define P_SIZE (2 * 1024 * 1024)
+#else
+/* add an overhead to the max kmalloc size for non-striped symbols/etc */
+#define P_SIZE (256 * 1024)
+#endif
+
+#define MAX_VPES 16
+
+static inline int aprp_cpu_index(void)
+{
+#ifdef CONFIG_MIPS_CMP
+	return setup_max_cpus;
+#else
+	extern int tclimit;
+	return tclimit;
+#endif
+}
+
+enum vpe_state {
+	VPE_STATE_UNUSED = 0,
+	VPE_STATE_INUSE,
+	VPE_STATE_RUNNING
+};
+
+enum tc_state {
+	TC_STATE_UNUSED = 0,
+	TC_STATE_INUSE,
+	TC_STATE_RUNNING,
+	TC_STATE_DYNAMIC
+};
+
+struct vpe {
+	enum vpe_state state;
+
+	/* (device) minor associated with this vpe */
+	int minor;
+
+	/* elfloader stuff */
+	void *load_addr;
+	unsigned long len;
+	char *pbuffer;
+	unsigned long plen;
+
+	unsigned long __start;
+
+	/* tc's associated with this vpe */
+	struct list_head tc;
+
+	/* The list of vpe's */
+	struct list_head list;
+
+	/* shared symbol address */
+	void *shared_ptr;
+
+	/* the list of who wants to know when something major happens */
+	struct list_head notify;
+
+	unsigned int ntcs;
+};
+
+struct tc {
+	enum tc_state state;
+	int index;
+
+	struct vpe *pvpe;	/* parent VPE */
+	struct list_head tc;	/* The list of TC's with this VPE */
+	struct list_head list;	/* The global list of tc's */
+};
+
+struct vpe_notifications {
+	void (*start)(int vpe);
+	void (*stop)(int vpe);
+
+	struct list_head list;
+};
+
+struct vpe_control {
+	spinlock_t vpe_list_lock;
+	struct list_head vpe_list;      /* Virtual processing elements */
+	spinlock_t tc_list_lock;
+	struct list_head tc_list;       /* Thread contexts */
+};
+
+extern unsigned long physical_memsize;
+extern struct vpe_control vpecontrol;
+extern const struct file_operations vpe_fops;
+
+int vpe_notify(int index, struct vpe_notifications *notify);
+
+void *vpe_get_shared(int index);
+
+struct vpe *get_vpe(int minor);
+struct tc *get_tc(int index);
+struct vpe *alloc_vpe(int minor);
+struct tc *alloc_tc(int index);
+void release_vpe(struct vpe *v);
+
+void *alloc_progmem(unsigned long len);
+void release_progmem(void *ptr);
+
+int vpe_run(struct vpe *v);
+void cleanup_tc(struct tc *tc);
+
+int __init vpe_module_init(void);
+void __exit vpe_module_exit(void);
+#endif /* _ASM_VPE_H */
diff --git a/arch/mips/include/asm/watch.h b/arch/mips/include/asm/watch.h
new file mode 100644
index 000000000..6ffe3eadf
--- /dev/null
+++ b/arch/mips/include/asm/watch.h
@@ -0,0 +1,32 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 David Daney
+ */
+#ifndef _ASM_WATCH_H
+#define _ASM_WATCH_H
+
+#include <linux/bitops.h>
+
+#include <asm/mipsregs.h>
+
+void mips_install_watch_registers(struct task_struct *t);
+void mips_read_watch_registers(void);
+void mips_clear_watch_registers(void);
+void mips_probe_watch_registers(struct cpuinfo_mips *c);
+
+#ifdef CONFIG_HARDWARE_WATCHPOINTS
+#define __restore_watch(task) do {					\
+	if (unlikely(test_bit(TIF_LOAD_WATCH,				\
+			      &task_thread_info(task)->flags))) {	\
+		mips_install_watch_registers(task);			\
+	}								\
+} while (0)
+
+#else
+#define __restore_watch(task) do {} while (0)
+#endif
+
+#endif /* _ASM_WATCH_H */
diff --git a/arch/mips/include/asm/wbflush.h b/arch/mips/include/asm/wbflush.h
new file mode 100644
index 000000000..eadc0ac47
--- /dev/null
+++ b/arch/mips/include/asm/wbflush.h
@@ -0,0 +1,34 @@
+/*
+ * Header file for using the wbflush routine
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (c) 1998 Harald Koerfgen
+ * Copyright (C) 2002 Maciej W. Rozycki
+ */
+#ifndef _ASM_WBFLUSH_H
+#define _ASM_WBFLUSH_H
+
+
+#ifdef CONFIG_CPU_HAS_WB
+
+extern void (*__wbflush)(void);
+extern void wbflush_setup(void);
+
+#define wbflush()			\
+	do {				\
+		__sync();		\
+		__wbflush();		\
+	} while (0)
+
+#else /* !CONFIG_CPU_HAS_WB */
+
+#define wbflush_setup() do { } while (0)
+
+#define wbflush() fast_iob()
+
+#endif /* !CONFIG_CPU_HAS_WB */
+
+#endif /* _ASM_WBFLUSH_H */
diff --git a/arch/mips/include/asm/xtalk/xtalk.h b/arch/mips/include/asm/xtalk/xtalk.h
new file mode 100644
index 000000000..680e7efeb
--- /dev/null
+++ b/arch/mips/include/asm/xtalk/xtalk.h
@@ -0,0 +1,52 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * xtalk.h -- platform-independent crosstalk interface, derived from
+ * IRIX <sys/PCI/bridge.h>, revision 1.38.
+ *
+ * Copyright (C) 1995 - 1997, 1999 Silcon Graphics, Inc.
+ * Copyright (C) 1999 Ralf Baechle (ralf@gnu.org)
+ */
+#ifndef _ASM_XTALK_XTALK_H
+#define _ASM_XTALK_XTALK_H
+
+#ifndef __ASSEMBLY__
+/*
+ * User-level device driver visible types
+ */
+typedef char		xwidgetnum_t;	/* xtalk widget number	(0..15) */
+
+#define XWIDGET_NONE		-1
+
+typedef int xwidget_part_num_t; /* xtalk widget part number */
+
+#define XWIDGET_PART_NUM_NONE	-1
+
+typedef int		xwidget_rev_num_t;	/* xtalk widget revision number */
+
+#define XWIDGET_REV_NUM_NONE	-1
+
+typedef int xwidget_mfg_num_t;	/* xtalk widget manufacturing ID */
+
+#define XWIDGET_MFG_NUM_NONE	-1
+
+typedef struct xtalk_piomap_s *xtalk_piomap_t;
+
+/* It is often convenient to fold the XIO target port
+ * number into the XIO address.
+ */
+#define XIO_NOWHERE	(0xFFFFFFFFFFFFFFFFull)
+#define XIO_ADDR_BITS	(0x0000FFFFFFFFFFFFull)
+#define XIO_PORT_BITS	(0xF000000000000000ull)
+#define XIO_PORT_SHIFT	(60)
+
+#define XIO_PACKED(x)	(((x)&XIO_PORT_BITS) != 0)
+#define XIO_ADDR(x)	((x)&XIO_ADDR_BITS)
+#define XIO_PORT(x)	((xwidgetnum_t)(((x)&XIO_PORT_BITS) >> XIO_PORT_SHIFT))
+#define XIO_PACK(p, o)	((((uint64_t)(p))<<XIO_PORT_SHIFT) | ((o)&XIO_ADDR_BITS))
+
+#endif /* !__ASSEMBLY__ */
+
+#endif /* _ASM_XTALK_XTALK_H */
diff --git a/arch/mips/include/asm/xtalk/xwidget.h b/arch/mips/include/asm/xtalk/xwidget.h
new file mode 100644
index 000000000..24f121da6
--- /dev/null
+++ b/arch/mips/include/asm/xtalk/xwidget.h
@@ -0,0 +1,279 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * xwidget.h - generic crosstalk widget header file, derived from IRIX
+ * <sys/xtalk/xtalkwidget.h>, revision 1.32.
+ *
+ * Copyright (C) 1996, 1999 Silcon Graphics, Inc.
+ * Copyright (C) 1999 Ralf Baechle (ralf@gnu.org)
+ */
+#ifndef _ASM_XTALK_XWIDGET_H
+#define _ASM_XTALK_XWIDGET_H
+
+#include <linux/types.h>
+#include <asm/xtalk/xtalk.h>
+
+#define WIDGET_ID			0x04
+#define WIDGET_STATUS			0x0c
+#define WIDGET_ERR_UPPER_ADDR		0x14
+#define WIDGET_ERR_LOWER_ADDR		0x1c
+#define WIDGET_CONTROL			0x24
+#define WIDGET_REQ_TIMEOUT		0x2c
+#define WIDGET_INTDEST_UPPER_ADDR	0x34
+#define WIDGET_INTDEST_LOWER_ADDR	0x3c
+#define WIDGET_ERR_CMD_WORD		0x44
+#define WIDGET_LLP_CFG			0x4c
+#define WIDGET_TFLUSH			0x54
+
+/* WIDGET_ID */
+#define WIDGET_REV_NUM			0xf0000000
+#define WIDGET_PART_NUM			0x0ffff000
+#define WIDGET_MFG_NUM			0x00000ffe
+#define WIDGET_REV_NUM_SHFT		28
+#define WIDGET_PART_NUM_SHFT		12
+#define WIDGET_MFG_NUM_SHFT		1
+
+#define XWIDGET_PART_NUM(widgetid) (((widgetid) & WIDGET_PART_NUM) >> WIDGET_PART_NUM_SHFT)
+#define XWIDGET_REV_NUM(widgetid) (((widgetid) & WIDGET_REV_NUM) >> WIDGET_REV_NUM_SHFT)
+#define XWIDGET_MFG_NUM(widgetid) (((widgetid) & WIDGET_MFG_NUM) >> WIDGET_MFG_NUM_SHFT)
+
+/* WIDGET_STATUS */
+#define WIDGET_LLP_REC_CNT		0xff000000
+#define WIDGET_LLP_TX_CNT		0x00ff0000
+#define WIDGET_PENDING			0x0000001f
+
+/* WIDGET_ERR_UPPER_ADDR */
+#define WIDGET_ERR_UPPER_ADDR_ONLY	0x0000ffff
+
+/* WIDGET_CONTROL */
+#define WIDGET_F_BAD_PKT		0x00010000
+#define WIDGET_LLP_XBAR_CRD		0x0000f000
+#define WIDGET_LLP_XBAR_CRD_SHFT	12
+#define WIDGET_CLR_RLLP_CNT		0x00000800
+#define WIDGET_CLR_TLLP_CNT		0x00000400
+#define WIDGET_SYS_END			0x00000200
+#define WIDGET_MAX_TRANS		0x000001f0
+#define WIDGET_WIDGET_ID		0x0000000f
+
+/* WIDGET_INTDEST_UPPER_ADDR */
+#define WIDGET_INT_VECTOR		0xff000000
+#define WIDGET_INT_VECTOR_SHFT		24
+#define WIDGET_TARGET_ID		0x000f0000
+#define WIDGET_TARGET_ID_SHFT		16
+#define WIDGET_UPP_ADDR			0x0000ffff
+
+/* WIDGET_ERR_CMD_WORD */
+#define WIDGET_DIDN			0xf0000000
+#define WIDGET_SIDN			0x0f000000
+#define WIDGET_PACTYP			0x00f00000
+#define WIDGET_TNUM			0x000f8000
+#define WIDGET_COHERENT			0x00004000
+#define WIDGET_DS			0x00003000
+#define WIDGET_GBR			0x00000800
+#define WIDGET_VBPM			0x00000400
+#define WIDGET_ERROR			0x00000200
+#define WIDGET_BARRIER			0x00000100
+
+/* WIDGET_LLP_CFG */
+#define WIDGET_LLP_MAXRETRY		0x03ff0000
+#define WIDGET_LLP_MAXRETRY_SHFT	16
+#define WIDGET_LLP_NULLTIMEOUT		0x0000fc00
+#define WIDGET_LLP_NULLTIMEOUT_SHFT	10
+#define WIDGET_LLP_MAXBURST		0x000003ff
+#define WIDGET_LLP_MAXBURST_SHFT	0
+
+/* Xtalk Widget Device Mfgr Nums */
+#define WIDGET_XBOW_MFGR_NUM	0x0      /* IP30 XBow Chip */
+#define WIDGET_XXBOW_MFGR_NUM	0x0      /* IP35 Xbow + XBridge Chip */
+#define WIDGET_ODYS_MFGR_NUM	0x023    /* Odyssey / VPro GFX */
+#define WIDGET_TPU_MFGR_NUM	0x024    /* Tensor Processor Unit */
+#define WIDGET_XBRDG_MFGR_NUM	0x024    /* IP35 XBridge Chip */
+#define WIDGET_HEART_MFGR_NUM	0x036    /* IP30 HEART Chip */
+#define WIDGET_BRIDG_MFGR_NUM	0x036    /* PCI Bridge */
+#define WIDGET_HUB_MFGR_NUM	0x036    /* IP27 Hub Chip */
+#define WIDGET_BDRCK_MFGR_NUM	0x036    /* IP35 Bedrock Chip */
+#define WIDGET_IMPCT_MFGR_NUM	0x2aa    /* HQ4 / Impact GFX */
+#define WIDGET_KONA_MFGR_NUM	0x2aa    /* InfiniteReality3 / Kona GFX */
+#define WIDGET_NULL_MFGR_NUM	-1       /* NULL */
+
+/* Xtalk Widget Device Part Nums */
+#define WIDGET_XBOW_PART_NUM	0x0000
+#define WIDGET_HEART_PART_NUM	0xc001
+#define WIDGET_BRIDG_PART_NUM	0xc002
+#define WIDGET_IMPCT_PART_NUM	0xc003
+#define WIDGET_ODYS_PART_NUM	0xc013
+#define WIDGET_HUB_PART_NUM	0xc101
+#define WIDGET_KONA_PART_NUM	0xc102
+#define WIDGET_BDRCK_PART_NUM	0xc110
+#define WIDGET_TPU_PART_NUM	0xc202
+#define WIDGET_XXBOW_PART_NUM	0xd000
+#define WIDGET_XBRDG_PART_NUM	0xd002
+#define WIDGET_NULL_PART_NUM	-1
+
+/* For Xtalk Widget identification */
+struct widget_ident {
+	u32 mfgr;
+	u32 part;
+	char *name;
+	char *revs[16];
+};
+
+/* Known Xtalk Widgets */
+static const struct widget_ident __initconst widget_idents[] = {
+	{
+		WIDGET_XBOW_MFGR_NUM,
+		WIDGET_XBOW_PART_NUM,
+		"xbow",
+		{NULL, "1.0", "1.1", "1.2", "1.3", "2.0", NULL},
+	},
+	{
+		WIDGET_HEART_MFGR_NUM,
+		WIDGET_HEART_PART_NUM,
+		"heart",
+		{NULL, "A", "B", "C", "D", "E", "F", NULL},
+	},
+	{
+		WIDGET_BRIDG_MFGR_NUM,
+		WIDGET_BRIDG_PART_NUM,
+		"bridge",
+		{NULL, "A", "B", "C", "D", NULL},
+	},
+	{
+		WIDGET_IMPCT_MFGR_NUM,
+		WIDGET_IMPCT_PART_NUM,
+		"impact",
+		{NULL, "A", "B", NULL},
+	},
+	{
+		WIDGET_ODYS_MFGR_NUM,
+		WIDGET_ODYS_PART_NUM,
+		"odyssey",
+		{NULL, "A", "B", NULL},
+	},
+	{
+		WIDGET_HUB_MFGR_NUM,
+		WIDGET_HUB_PART_NUM,
+		"hub",
+		{NULL, "1.0", "2.0", "2.1", "2.2", "2.3", "2.4", NULL},
+	},
+	{
+		WIDGET_KONA_MFGR_NUM,
+		WIDGET_KONA_PART_NUM,
+		"kona",
+		{NULL},
+	},
+	{
+		WIDGET_BDRCK_MFGR_NUM,
+		WIDGET_BDRCK_PART_NUM,
+		"bedrock",
+		{NULL, "1.0", "1.1", NULL},
+	},
+	{
+		WIDGET_TPU_MFGR_NUM,
+		WIDGET_TPU_PART_NUM,
+		"tpu",
+		{"0", NULL},
+	},
+	{
+		WIDGET_XXBOW_MFGR_NUM,
+		WIDGET_XXBOW_PART_NUM,
+		"xxbow",
+		{NULL, "1.0", "2.0", NULL},
+	},
+	{
+		WIDGET_XBRDG_MFGR_NUM,
+		WIDGET_XBRDG_PART_NUM,
+		"xbridge",
+		{NULL, "A", "B", NULL},
+	},
+	{
+		WIDGET_NULL_MFGR_NUM,
+		WIDGET_NULL_PART_NUM,
+		NULL,
+		{NULL},
+	}
+};
+
+/*
+ * according to the crosstalk spec, only 32-bits access to the widget
+ * configuration registers is allowed.	some widgets may allow 64-bits
+ * access but software should not depend on it.	 registers beyond the
+ * widget target flush register are widget dependent thus will not be
+ * defined here
+ */
+#ifndef __ASSEMBLY__
+typedef u32 widgetreg_t;
+
+/* widget configuration registers */
+typedef volatile struct widget_cfg {
+	widgetreg_t		w_pad_0;		/* 0x00 */
+	widgetreg_t		w_id;			/* 0x04 */
+	widgetreg_t		w_pad_1;		/* 0x08 */
+	widgetreg_t		w_status;		/* 0x0c */
+	widgetreg_t		w_pad_2;		/* 0x10 */
+	widgetreg_t		w_err_upper_addr;	/* 0x14 */
+	widgetreg_t		w_pad_3;		/* 0x18 */
+	widgetreg_t		w_err_lower_addr;	/* 0x1c */
+	widgetreg_t		w_pad_4;		/* 0x20 */
+	widgetreg_t		w_control;		/* 0x24 */
+	widgetreg_t		w_pad_5;		/* 0x28 */
+	widgetreg_t		w_req_timeout;		/* 0x2c */
+	widgetreg_t		w_pad_6;		/* 0x30 */
+	widgetreg_t		w_intdest_upper_addr;	/* 0x34 */
+	widgetreg_t		w_pad_7;		/* 0x38 */
+	widgetreg_t		w_intdest_lower_addr;	/* 0x3c */
+	widgetreg_t		w_pad_8;		/* 0x40 */
+	widgetreg_t		w_err_cmd_word;		/* 0x44 */
+	widgetreg_t		w_pad_9;		/* 0x48 */
+	widgetreg_t		w_llp_cfg;		/* 0x4c */
+	widgetreg_t		w_pad_10;		/* 0x50 */
+	widgetreg_t		w_tflush;		/* 0x54 */
+} widget_cfg_t;
+
+typedef struct {
+	unsigned	didn:4;
+	unsigned	sidn:4;
+	unsigned	pactyp:4;
+	unsigned	tnum:5;
+	unsigned	ct:1;
+	unsigned	ds:2;
+	unsigned	gbr:1;
+	unsigned	vbpm:1;
+	unsigned	error:1;
+	unsigned	bo:1;
+	unsigned	other:8;
+} w_err_cmd_word_f;
+
+typedef union {
+	widgetreg_t		r;
+	w_err_cmd_word_f	f;
+} w_err_cmd_word_u;
+
+typedef struct xwidget_info_s *xwidget_info_t;
+
+/*
+ * Crosstalk Widget Hardware Identification, as defined in the Crosstalk spec.
+ */
+typedef struct xwidget_hwid_s {
+	xwidget_part_num_t	part_num;
+	xwidget_rev_num_t	rev_num;
+	xwidget_mfg_num_t	mfg_num;
+} *xwidget_hwid_t;
+
+
+/*
+ * Returns 1 if a driver that handles devices described by hwid1 is able
+ * to manage a device with hardwareid hwid2.  NOTE: We don't check rev
+ * numbers at all.
+ */
+#define XWIDGET_HARDWARE_ID_MATCH(hwid1, hwid2) \
+	(((hwid1)->part_num == (hwid2)->part_num) && \
+	(((hwid1)->mfg_num == XWIDGET_MFG_NUM_NONE) || \
+	((hwid2)->mfg_num == XWIDGET_MFG_NUM_NONE) || \
+	((hwid1)->mfg_num == (hwid2)->mfg_num)))
+
+#endif /* !__ASSEMBLY__ */
+
+#endif /* _ASM_XTALK_XWIDGET_H */
diff --git a/arch/mips/include/asm/yamon-dt.h b/arch/mips/include/asm/yamon-dt.h
new file mode 100644
index 000000000..e20475540
--- /dev/null
+++ b/arch/mips/include/asm/yamon-dt.h
@@ -0,0 +1,60 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2016 Imagination Technologies
+ * Author: Paul Burton <paul.burton@mips.com>
+ */
+
+#ifndef __MIPS_ASM_YAMON_DT_H__
+#define __MIPS_ASM_YAMON_DT_H__
+
+#include <linux/types.h>
+
+/**
+ * struct yamon_mem_region - Represents a contiguous range of physical RAM.
+ * @start:	Start physical address.
+ * @size:	Maximum size of region.
+ * @discard:	Length of additional memory to discard after the region.
+ */
+struct yamon_mem_region {
+	phys_addr_t	start;
+	phys_addr_t	size;
+	phys_addr_t	discard;
+};
+
+/**
+ * yamon_dt_append_cmdline() - Append YAMON-provided command line to /chosen
+ * @fdt: the FDT blob
+ *
+ * Write the YAMON-provided command line to the bootargs property of the
+ * /chosen node in @fdt.
+ *
+ * Return: 0 on success, else -errno
+ */
+extern __init int yamon_dt_append_cmdline(void *fdt);
+
+/**
+ * yamon_dt_append_memory() - Append YAMON-provided memory info to /memory
+ * @fdt:	the FDT blob
+ * @regions:	zero size terminated array of physical memory regions
+ *
+ * Generate a /memory node in @fdt based upon memory size information provided
+ * by YAMON in its environment and the @regions array.
+ *
+ * Return: 0 on success, else -errno
+ */
+extern __init int yamon_dt_append_memory(void *fdt,
+					const struct yamon_mem_region *regions);
+
+/**
+ * yamon_dt_serial_config() - Append YAMON-provided serial config to /chosen
+ * @fdt: the FDT blob
+ *
+ * Generate a stdout-path property in the /chosen node of @fdt, based upon
+ * information provided in the YAMON environment about the UART configuration
+ * of the system.
+ *
+ * Return: 0 on success, else -errno
+ */
+extern __init int yamon_dt_serial_config(void *fdt);
+
+#endif /* __MIPS_ASM_YAMON_DT_H__ */
diff --git a/arch/mips/include/uapi/asm/Kbuild b/arch/mips/include/uapi/asm/Kbuild
new file mode 100644
index 000000000..fdb9c5412
--- /dev/null
+++ b/arch/mips/include/uapi/asm/Kbuild
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0
+generated-y += unistd_n32.h
+generated-y += unistd_n64.h
+generated-y += unistd_o32.h
+
+generic-y += kvm_para.h
diff --git a/arch/mips/include/uapi/asm/auxvec.h b/arch/mips/include/uapi/asm/auxvec.h
new file mode 100644
index 000000000..612c2c41f
--- /dev/null
+++ b/arch/mips/include/uapi/asm/auxvec.h
@@ -0,0 +1,20 @@
+/* SPDX-License-Identifier: GPL-2.0+ WITH Linux-syscall-note */
+/*
+ * Copyright (C) 2015 Imagination Technologies
+ * Author: Alex Smith <alex.smith@imgtec.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#ifndef __ASM_AUXVEC_H
+#define __ASM_AUXVEC_H
+
+/* Location of VDSO image. */
+#define AT_SYSINFO_EHDR		33
+
+#define AT_VECTOR_SIZE_ARCH 1 /* entries in ARCH_DLINFO */
+
+#endif /* __ASM_AUXVEC_H */
diff --git a/arch/mips/include/uapi/asm/bitfield.h b/arch/mips/include/uapi/asm/bitfield.h
new file mode 100644
index 000000000..b11713d87
--- /dev/null
+++ b/arch/mips/include/uapi/asm/bitfield.h
@@ -0,0 +1,30 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2014 by Ralf Baechle <ralf@linux-mips.org>
+ */
+#ifndef __UAPI_ASM_BITFIELD_H
+#define __UAPI_ASM_BITFIELD_H
+
+/*
+ *  * Damn ...  bitfields depend from byteorder :-(
+ *   */
+#ifdef __MIPSEB__
+#define __BITFIELD_FIELD(field, more)					\
+	field;								\
+	more
+
+#elif defined(__MIPSEL__)
+
+#define __BITFIELD_FIELD(field, more)					\
+	more								\
+	field;
+
+#else /* !defined (__MIPSEB__) && !defined (__MIPSEL__) */
+#error "MIPS but neither __MIPSEL__ nor __MIPSEB__?"
+#endif
+
+#endif /* __UAPI_ASM_BITFIELD_H */
diff --git a/arch/mips/include/uapi/asm/bitsperlong.h b/arch/mips/include/uapi/asm/bitsperlong.h
new file mode 100644
index 000000000..7268380d8
--- /dev/null
+++ b/arch/mips/include/uapi/asm/bitsperlong.h
@@ -0,0 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+#ifndef __ASM_MIPS_BITSPERLONG_H
+#define __ASM_MIPS_BITSPERLONG_H
+
+#define __BITS_PER_LONG _MIPS_SZLONG
+
+#include <asm-generic/bitsperlong.h>
+
+#endif /* __ASM_MIPS_BITSPERLONG_H */
diff --git a/arch/mips/include/uapi/asm/break.h b/arch/mips/include/uapi/asm/break.h
new file mode 100644
index 000000000..10380b1bc
--- /dev/null
+++ b/arch/mips/include/uapi/asm/break.h
@@ -0,0 +1,32 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995, 2003 by Ralf Baechle
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ */
+#ifndef __UAPI_ASM_BREAK_H
+#define __UAPI_ASM_BREAK_H
+
+/*
+ * The following break codes are or were in use for specific purposes in
+ * other MIPS operating systems.  Linux/MIPS doesn't use all of them.  The
+ * unused ones are here as placeholders; we might encounter them in
+ * non-Linux/MIPS object files or make use of them in the future.
+ */
+#define BRK_USERBP	0	/* User bp (used by debuggers) */
+#define BRK_SSTEPBP	5	/* User bp (used by debuggers) */
+#define BRK_OVERFLOW	6	/* Overflow check */
+#define BRK_DIVZERO	7	/* Divide by zero check */
+#define BRK_RANGE	8	/* Range error check */
+#define BRK_BUG		12	/* Used by BUG() */
+#define BRK_UPROBE	13	/* See <asm/uprobes.h> */
+#define BRK_UPROBE_XOL	14	/* See <asm/uprobes.h> */
+#define BRK_MEMU	514	/* Used by FPU emulator */
+#define BRK_KPROBE_BP	515	/* Kprobe break */
+#define BRK_KPROBE_SSTEPBP 516	/* Kprobe single step software implementation */
+#define BRK_MULOVF	1023	/* Multiply overflow */
+
+#endif /* __UAPI_ASM_BREAK_H */
diff --git a/arch/mips/include/uapi/asm/byteorder.h b/arch/mips/include/uapi/asm/byteorder.h
new file mode 100644
index 000000000..b4edc85f9
--- /dev/null
+++ b/arch/mips/include/uapi/asm/byteorder.h
@@ -0,0 +1,20 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1996, 99, 2003 by Ralf Baechle
+ */
+#ifndef _ASM_BYTEORDER_H
+#define _ASM_BYTEORDER_H
+
+#if defined(__MIPSEB__)
+#include <linux/byteorder/big_endian.h>
+#elif defined(__MIPSEL__)
+#include <linux/byteorder/little_endian.h>
+#else
+# error "MIPS, but neither __MIPSEB__, nor __MIPSEL__???"
+#endif
+
+#endif /* _ASM_BYTEORDER_H */
diff --git a/arch/mips/include/uapi/asm/cachectl.h b/arch/mips/include/uapi/asm/cachectl.h
new file mode 100644
index 000000000..af7639ff4
--- /dev/null
+++ b/arch/mips/include/uapi/asm/cachectl.h
@@ -0,0 +1,27 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994, 1995, 1996 by Ralf Baechle
+ */
+#ifndef _ASM_CACHECTL
+#define _ASM_CACHECTL
+
+/*
+ * Options for cacheflush system call
+ */
+#define ICACHE	(1<<0)		/* flush instruction cache	  */
+#define DCACHE	(1<<1)		/* writeback and flush data cache */
+#define BCACHE	(ICACHE|DCACHE) /* flush both caches		  */
+
+/*
+ * Caching modes for the cachectl(2) call
+ *
+ * cachectl(2) is currently not supported and returns ENOSYS.
+ */
+#define CACHEABLE	0	/* make pages cacheable */
+#define UNCACHEABLE	1	/* make pages uncacheable */
+
+#endif	/* _ASM_CACHECTL */
diff --git a/arch/mips/include/uapi/asm/errno.h b/arch/mips/include/uapi/asm/errno.h
new file mode 100644
index 000000000..2fb714e2d
--- /dev/null
+++ b/arch/mips/include/uapi/asm/errno.h
@@ -0,0 +1,130 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995, 1999, 2001, 2002 by Ralf Baechle
+ */
+#ifndef _UAPI_ASM_ERRNO_H
+#define _UAPI_ASM_ERRNO_H
+
+/*
+ * These error numbers are intended to be MIPS ABI compatible
+ */
+
+#include <asm-generic/errno-base.h>
+
+#define ENOMSG		35	/* No message of desired type */
+#define EIDRM		36	/* Identifier removed */
+#define ECHRNG		37	/* Channel number out of range */
+#define EL2NSYNC	38	/* Level 2 not synchronized */
+#define EL3HLT		39	/* Level 3 halted */
+#define EL3RST		40	/* Level 3 reset */
+#define ELNRNG		41	/* Link number out of range */
+#define EUNATCH		42	/* Protocol driver not attached */
+#define ENOCSI		43	/* No CSI structure available */
+#define EL2HLT		44	/* Level 2 halted */
+#define EDEADLK		45	/* Resource deadlock would occur */
+#define ENOLCK		46	/* No record locks available */
+#define EBADE		50	/* Invalid exchange */
+#define EBADR		51	/* Invalid request descriptor */
+#define EXFULL		52	/* Exchange full */
+#define ENOANO		53	/* No anode */
+#define EBADRQC		54	/* Invalid request code */
+#define EBADSLT		55	/* Invalid slot */
+#define EDEADLOCK	56	/* File locking deadlock error */
+#define EBFONT		59	/* Bad font file format */
+#define ENOSTR		60	/* Device not a stream */
+#define ENODATA		61	/* No data available */
+#define ETIME		62	/* Timer expired */
+#define ENOSR		63	/* Out of streams resources */
+#define ENONET		64	/* Machine is not on the network */
+#define ENOPKG		65	/* Package not installed */
+#define EREMOTE		66	/* Object is remote */
+#define ENOLINK		67	/* Link has been severed */
+#define EADV		68	/* Advertise error */
+#define ESRMNT		69	/* Srmount error */
+#define ECOMM		70	/* Communication error on send */
+#define EPROTO		71	/* Protocol error */
+#define EDOTDOT		73	/* RFS specific error */
+#define EMULTIHOP	74	/* Multihop attempted */
+#define EBADMSG		77	/* Not a data message */
+#define ENAMETOOLONG	78	/* File name too long */
+#define EOVERFLOW	79	/* Value too large for defined data type */
+#define ENOTUNIQ	80	/* Name not unique on network */
+#define EBADFD		81	/* File descriptor in bad state */
+#define EREMCHG		82	/* Remote address changed */
+#define ELIBACC		83	/* Can not access a needed shared library */
+#define ELIBBAD		84	/* Accessing a corrupted shared library */
+#define ELIBSCN		85	/* .lib section in a.out corrupted */
+#define ELIBMAX		86	/* Attempting to link in too many shared libraries */
+#define ELIBEXEC	87	/* Cannot exec a shared library directly */
+#define EILSEQ		88	/* Illegal byte sequence */
+#define ENOSYS		89	/* Function not implemented */
+#define ELOOP		90	/* Too many symbolic links encountered */
+#define ERESTART	91	/* Interrupted system call should be restarted */
+#define ESTRPIPE	92	/* Streams pipe error */
+#define ENOTEMPTY	93	/* Directory not empty */
+#define EUSERS		94	/* Too many users */
+#define ENOTSOCK	95	/* Socket operation on non-socket */
+#define EDESTADDRREQ	96	/* Destination address required */
+#define EMSGSIZE	97	/* Message too long */
+#define EPROTOTYPE	98	/* Protocol wrong type for socket */
+#define ENOPROTOOPT	99	/* Protocol not available */
+#define EPROTONOSUPPORT 120	/* Protocol not supported */
+#define ESOCKTNOSUPPORT 121	/* Socket type not supported */
+#define EOPNOTSUPP	122	/* Operation not supported on transport endpoint */
+#define EPFNOSUPPORT	123	/* Protocol family not supported */
+#define EAFNOSUPPORT	124	/* Address family not supported by protocol */
+#define EADDRINUSE	125	/* Address already in use */
+#define EADDRNOTAVAIL	126	/* Cannot assign requested address */
+#define ENETDOWN	127	/* Network is down */
+#define ENETUNREACH	128	/* Network is unreachable */
+#define ENETRESET	129	/* Network dropped connection because of reset */
+#define ECONNABORTED	130	/* Software caused connection abort */
+#define ECONNRESET	131	/* Connection reset by peer */
+#define ENOBUFS		132	/* No buffer space available */
+#define EISCONN		133	/* Transport endpoint is already connected */
+#define ENOTCONN	134	/* Transport endpoint is not connected */
+#define EUCLEAN		135	/* Structure needs cleaning */
+#define ENOTNAM		137	/* Not a XENIX named type file */
+#define ENAVAIL		138	/* No XENIX semaphores available */
+#define EISNAM		139	/* Is a named type file */
+#define EREMOTEIO	140	/* Remote I/O error */
+#define EINIT		141	/* Reserved */
+#define EREMDEV		142	/* Error 142 */
+#define ESHUTDOWN	143	/* Cannot send after transport endpoint shutdown */
+#define ETOOMANYREFS	144	/* Too many references: cannot splice */
+#define ETIMEDOUT	145	/* Connection timed out */
+#define ECONNREFUSED	146	/* Connection refused */
+#define EHOSTDOWN	147	/* Host is down */
+#define EHOSTUNREACH	148	/* No route to host */
+#define EWOULDBLOCK	EAGAIN	/* Operation would block */
+#define EALREADY	149	/* Operation already in progress */
+#define EINPROGRESS	150	/* Operation now in progress */
+#define ESTALE		151	/* Stale file handle */
+#define ECANCELED	158	/* AIO operation canceled */
+
+/*
+ * These error are Linux extensions.
+ */
+#define ENOMEDIUM	159	/* No medium found */
+#define EMEDIUMTYPE	160	/* Wrong medium type */
+#define ENOKEY		161	/* Required key not available */
+#define EKEYEXPIRED	162	/* Key has expired */
+#define EKEYREVOKED	163	/* Key has been revoked */
+#define EKEYREJECTED	164	/* Key was rejected by service */
+
+/* for robust mutexes */
+#define EOWNERDEAD	165	/* Owner died */
+#define ENOTRECOVERABLE 166	/* State not recoverable */
+
+#define ERFKILL		167	/* Operation not possible due to RF-kill */
+
+#define EHWPOISON	168	/* Memory page has hardware error */
+
+#define EDQUOT		1133	/* Quota exceeded */
+
+
+#endif /* _UAPI_ASM_ERRNO_H */
diff --git a/arch/mips/include/uapi/asm/fcntl.h b/arch/mips/include/uapi/asm/fcntl.h
new file mode 100644
index 000000000..0369a38e3
--- /dev/null
+++ b/arch/mips/include/uapi/asm/fcntl.h
@@ -0,0 +1,60 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995, 96, 97, 98, 99, 2003, 05 Ralf Baechle
+ */
+#ifndef _UAPI_ASM_FCNTL_H
+#define _UAPI_ASM_FCNTL_H
+
+#include <asm/sgidefs.h>
+
+#define O_APPEND	0x0008
+#define O_DSYNC		0x0010	/* used to be O_SYNC, see below */
+#define O_NONBLOCK	0x0080
+#define O_CREAT		0x0100	/* not fcntl */
+#define O_TRUNC		0x0200	/* not fcntl */
+#define O_EXCL		0x0400	/* not fcntl */
+#define O_NOCTTY	0x0800	/* not fcntl */
+#define FASYNC		0x1000	/* fcntl, for BSD compatibility */
+#define O_LARGEFILE	0x2000	/* allow large file opens */
+/*
+ * Before Linux 2.6.33 only O_DSYNC semantics were implemented, but using
+ * the O_SYNC flag.  We continue to use the existing numerical value
+ * for O_DSYNC semantics now, but using the correct symbolic name for it.
+ * This new value is used to request true Posix O_SYNC semantics.  It is
+ * defined in this strange way to make sure applications compiled against
+ * new headers get at least O_DSYNC semantics on older kernels.
+ *
+ * This has the nice side-effect that we can simply test for O_DSYNC
+ * wherever we do not care if O_DSYNC or O_SYNC is used.
+ *
+ * Note: __O_SYNC must never be used directly.
+ */
+#define __O_SYNC	0x4000
+#define O_SYNC		(__O_SYNC|O_DSYNC)
+#define O_DIRECT	0x8000	/* direct disk access hint */
+
+#define F_GETLK		14
+#define F_SETLK		6
+#define F_SETLKW	7
+
+#define F_SETOWN	24	/*  for sockets. */
+#define F_GETOWN	23	/*  for sockets. */
+
+#if __BITS_PER_LONG == 32 || defined(__KERNEL__)
+#define F_GETLK64	33	/*  using 'struct flock64' */
+#define F_SETLK64	34
+#define F_SETLKW64	35
+#endif /* __BITS_PER_LONG == 32 || defined(__KERNEL__) */
+
+#if _MIPS_SIM != _MIPS_SIM_ABI64
+#define __ARCH_FLOCK_EXTRA_SYSID	long l_sysid;
+#define __ARCH_FLOCK_PAD		long pad[4];
+#endif
+
+#include <asm-generic/fcntl.h>
+
+#endif /* _UAPI_ASM_FCNTL_H */
diff --git a/arch/mips/include/uapi/asm/hwcap.h b/arch/mips/include/uapi/asm/hwcap.h
new file mode 100644
index 000000000..b7e02bdc1
--- /dev/null
+++ b/arch/mips/include/uapi/asm/hwcap.h
@@ -0,0 +1,22 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+#ifndef _UAPI_ASM_HWCAP_H
+#define _UAPI_ASM_HWCAP_H
+
+/* HWCAP flags */
+#define HWCAP_MIPS_R6		(1 << 0)
+#define HWCAP_MIPS_MSA		(1 << 1)
+#define HWCAP_MIPS_CRC32	(1 << 2)
+#define HWCAP_MIPS_MIPS16	(1 << 3)
+#define HWCAP_MIPS_MDMX     (1 << 4)
+#define HWCAP_MIPS_MIPS3D   (1 << 5)
+#define HWCAP_MIPS_SMARTMIPS (1 << 6)
+#define HWCAP_MIPS_DSP      (1 << 7)
+#define HWCAP_MIPS_DSP2     (1 << 8)
+#define HWCAP_MIPS_DSP3     (1 << 9)
+#define HWCAP_MIPS_MIPS16E2 (1 << 10)
+#define HWCAP_LOONGSON_MMI  (1 << 11)
+#define HWCAP_LOONGSON_EXT  (1 << 12)
+#define HWCAP_LOONGSON_EXT2 (1 << 13)
+#define HWCAP_LOONGSON_CPUCFG (1 << 14)
+
+#endif /* _UAPI_ASM_HWCAP_H */
diff --git a/arch/mips/include/uapi/asm/inst.h b/arch/mips/include/uapi/asm/inst.h
new file mode 100644
index 000000000..43d1faa02
--- /dev/null
+++ b/arch/mips/include/uapi/asm/inst.h
@@ -0,0 +1,1141 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * Format of an instruction in memory.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1996, 2000 by Ralf Baechle
+ * Copyright (C) 2006 by Thiemo Seufer
+ * Copyright (C) 2012 MIPS Technologies, Inc.  All rights reserved.
+ * Copyright (C) 2014 Imagination Technologies Ltd.
+ */
+#ifndef _UAPI_ASM_INST_H
+#define _UAPI_ASM_INST_H
+
+#include <asm/bitfield.h>
+
+/*
+ * Major opcodes; before MIPS IV cop1x was called cop3.
+ */
+enum major_op {
+	spec_op, bcond_op, j_op, jal_op,
+	beq_op, bne_op, blez_op, bgtz_op,
+	addi_op, pop10_op = addi_op, addiu_op, slti_op, sltiu_op,
+	andi_op, ori_op, xori_op, lui_op,
+	cop0_op, cop1_op, cop2_op, cop1x_op,
+	beql_op, bnel_op, blezl_op, bgtzl_op,
+	daddi_op, pop30_op = daddi_op, daddiu_op, ldl_op, ldr_op,
+	spec2_op, jalx_op, mdmx_op, msa_op = mdmx_op, spec3_op,
+	lb_op, lh_op, lwl_op, lw_op,
+	lbu_op, lhu_op, lwr_op, lwu_op,
+	sb_op, sh_op, swl_op, sw_op,
+	sdl_op, sdr_op, swr_op, cache_op,
+	ll_op, lwc1_op, lwc2_op, bc6_op = lwc2_op, pref_op,
+	lld_op, ldc1_op, ldc2_op, pop66_op = ldc2_op, ld_op,
+	sc_op, swc1_op, swc2_op, balc6_op = swc2_op, major_3b_op,
+	scd_op, sdc1_op, sdc2_op, pop76_op = sdc2_op, sd_op
+};
+
+/*
+ * func field of spec opcode.
+ */
+enum spec_op {
+	sll_op, movc_op, srl_op, sra_op,
+	sllv_op, pmon_op, srlv_op, srav_op,
+	jr_op, jalr_op, movz_op, movn_op,
+	syscall_op, break_op, spim_op, sync_op,
+	mfhi_op, mthi_op, mflo_op, mtlo_op,
+	dsllv_op, spec2_unused_op, dsrlv_op, dsrav_op,
+	mult_op, multu_op, div_op, divu_op,
+	dmult_op, dmultu_op, ddiv_op, ddivu_op,
+	add_op, addu_op, sub_op, subu_op,
+	and_op, or_op, xor_op, nor_op,
+	spec3_unused_op, spec4_unused_op, slt_op, sltu_op,
+	dadd_op, daddu_op, dsub_op, dsubu_op,
+	tge_op, tgeu_op, tlt_op, tltu_op,
+	teq_op, seleqz_op, tne_op, selnez_op,
+	dsll_op, spec5_unused_op, dsrl_op, dsra_op,
+	dsll32_op, spec6_unused_op, dsrl32_op, dsra32_op
+};
+
+/*
+ * func field of spec2 opcode.
+ */
+enum spec2_op {
+	madd_op, maddu_op, mul_op, spec2_3_unused_op,
+	msub_op, msubu_op, /* more unused ops */
+	clz_op = 0x20, clo_op,
+	dclz_op = 0x24, dclo_op,
+	sdbpp_op = 0x3f
+};
+
+/*
+ * func field of spec3 opcode.
+ */
+enum spec3_op {
+	ext_op, dextm_op, dextu_op, dext_op,
+	ins_op, dinsm_op, dinsu_op, dins_op,
+	yield_op  = 0x09, lx_op     = 0x0a,
+	lwle_op   = 0x19, lwre_op   = 0x1a,
+	cachee_op = 0x1b, sbe_op    = 0x1c,
+	she_op    = 0x1d, sce_op    = 0x1e,
+	swe_op    = 0x1f, bshfl_op  = 0x20,
+	swle_op   = 0x21, swre_op   = 0x22,
+	prefe_op  = 0x23, dbshfl_op = 0x24,
+	cache6_op = 0x25, sc6_op    = 0x26,
+	scd6_op   = 0x27, lbue_op   = 0x28,
+	lhue_op   = 0x29, lbe_op    = 0x2c,
+	lhe_op    = 0x2d, lle_op    = 0x2e,
+	lwe_op    = 0x2f, pref6_op  = 0x35,
+	ll6_op    = 0x36, lld6_op   = 0x37,
+	rdhwr_op  = 0x3b
+};
+
+/*
+ * Bits 10-6 minor opcode for r6 spec mult/div encodings
+ */
+enum mult_op {
+	mult_mult_op = 0x0,
+	mult_mul_op = 0x2,
+	mult_muh_op = 0x3,
+};
+enum multu_op {
+	multu_multu_op = 0x0,
+	multu_mulu_op = 0x2,
+	multu_muhu_op = 0x3,
+};
+enum div_op {
+	div_div_op = 0x0,
+	div_div6_op = 0x2,
+	div_mod_op = 0x3,
+};
+enum divu_op {
+	divu_divu_op = 0x0,
+	divu_divu6_op = 0x2,
+	divu_modu_op = 0x3,
+};
+enum dmult_op {
+	dmult_dmult_op = 0x0,
+	dmult_dmul_op = 0x2,
+	dmult_dmuh_op = 0x3,
+};
+enum dmultu_op {
+	dmultu_dmultu_op = 0x0,
+	dmultu_dmulu_op = 0x2,
+	dmultu_dmuhu_op = 0x3,
+};
+enum ddiv_op {
+	ddiv_ddiv_op = 0x0,
+	ddiv_ddiv6_op = 0x2,
+	ddiv_dmod_op = 0x3,
+};
+enum ddivu_op {
+	ddivu_ddivu_op = 0x0,
+	ddivu_ddivu6_op = 0x2,
+	ddivu_dmodu_op = 0x3,
+};
+
+/*
+ * rt field of bcond opcodes.
+ */
+enum rt_op {
+	bltz_op, bgez_op, bltzl_op, bgezl_op,
+	spimi_op, unused_rt_op_0x05, unused_rt_op_0x06, unused_rt_op_0x07,
+	tgei_op, tgeiu_op, tlti_op, tltiu_op,
+	teqi_op, unused_0x0d_rt_op, tnei_op, unused_0x0f_rt_op,
+	bltzal_op, bgezal_op, bltzall_op, bgezall_op,
+	rt_op_0x14, rt_op_0x15, rt_op_0x16, rt_op_0x17,
+	rt_op_0x18, rt_op_0x19, rt_op_0x1a, rt_op_0x1b,
+	bposge32_op, rt_op_0x1d, rt_op_0x1e, synci_op
+};
+
+/*
+ * rs field of cop opcodes.
+ */
+enum cop_op {
+	mfc_op	      = 0x00, dmfc_op	    = 0x01,
+	cfc_op	      = 0x02, mfhc0_op	    = 0x02,
+	mfhc_op       = 0x03, mtc_op	    = 0x04,
+	dmtc_op	      = 0x05, ctc_op	    = 0x06,
+	mthc0_op      = 0x06, mthc_op	    = 0x07,
+	bc_op	      = 0x08, bc1eqz_op     = 0x09,
+	mfmc0_op      = 0x0b, bc1nez_op     = 0x0d,
+	wrpgpr_op     = 0x0e, cop_op	    = 0x10,
+	copm_op	      = 0x18
+};
+
+/*
+ * rt field of cop.bc_op opcodes
+ */
+enum bcop_op {
+	bcf_op, bct_op, bcfl_op, bctl_op
+};
+
+/*
+ * func field of cop0 coi opcodes.
+ */
+enum cop0_coi_func {
+	tlbr_op	      = 0x01, tlbwi_op	    = 0x02,
+	tlbwr_op      = 0x06, tlbp_op	    = 0x08,
+	rfe_op	      = 0x10, eret_op	    = 0x18,
+	wait_op       = 0x20, hypcall_op    = 0x28
+};
+
+/*
+ * func field of cop0 com opcodes.
+ */
+enum cop0_com_func {
+	tlbr1_op      = 0x01, tlbw_op	    = 0x02,
+	tlbp1_op      = 0x08, dctr_op	    = 0x09,
+	dctw_op	      = 0x0a
+};
+
+/*
+ * fmt field of cop1 opcodes.
+ */
+enum cop1_fmt {
+	s_fmt, d_fmt, e_fmt, q_fmt,
+	w_fmt, l_fmt
+};
+
+/*
+ * func field of cop1 instructions using d, s or w format.
+ */
+enum cop1_sdw_func {
+	fadd_op	     =	0x00, fsub_op	   =  0x01,
+	fmul_op	     =	0x02, fdiv_op	   =  0x03,
+	fsqrt_op     =	0x04, fabs_op	   =  0x05,
+	fmov_op	     =	0x06, fneg_op	   =  0x07,
+	froundl_op   =	0x08, ftruncl_op   =  0x09,
+	fceill_op    =	0x0a, ffloorl_op   =  0x0b,
+	fround_op    =	0x0c, ftrunc_op	   =  0x0d,
+	fceil_op     =	0x0e, ffloor_op	   =  0x0f,
+	fsel_op      =  0x10,
+	fmovc_op     =	0x11, fmovz_op	   =  0x12,
+	fmovn_op     =	0x13, fseleqz_op   =  0x14,
+	frecip_op    =  0x15, frsqrt_op    =  0x16,
+	fselnez_op   =  0x17, fmaddf_op    =  0x18,
+	fmsubf_op    =  0x19, frint_op     =  0x1a,
+	fclass_op    =  0x1b, fmin_op      =  0x1c,
+	fmina_op     =  0x1d, fmax_op      =  0x1e,
+	fmaxa_op     =  0x1f, fcvts_op     =  0x20,
+	fcvtd_op     =	0x21, fcvte_op	   =  0x22,
+	fcvtw_op     =	0x24, fcvtl_op	   =  0x25,
+	fcmp_op	     =	0x30
+};
+
+/*
+ * func field of cop1x opcodes (MIPS IV).
+ */
+enum cop1x_func {
+	lwxc1_op     =	0x00, ldxc1_op	   =  0x01,
+	swxc1_op     =  0x08, sdxc1_op	   =  0x09,
+	pfetch_op    =	0x0f, madd_s_op	   =  0x20,
+	madd_d_op    =	0x21, madd_e_op	   =  0x22,
+	msub_s_op    =	0x28, msub_d_op	   =  0x29,
+	msub_e_op    =	0x2a, nmadd_s_op   =  0x30,
+	nmadd_d_op   =	0x31, nmadd_e_op   =  0x32,
+	nmsub_s_op   =	0x38, nmsub_d_op   =  0x39,
+	nmsub_e_op   =	0x3a
+};
+
+/*
+ * func field for mad opcodes (MIPS IV).
+ */
+enum mad_func {
+	madd_fp_op	= 0x08, msub_fp_op	= 0x0a,
+	nmadd_fp_op	= 0x0c, nmsub_fp_op	= 0x0e
+};
+
+/*
+ * func field for page table walker (Loongson-3).
+ */
+enum ptw_func {
+	lwdir_op = 0x00,
+	lwpte_op = 0x01,
+	lddir_op = 0x02,
+	ldpte_op = 0x03,
+};
+
+/*
+ * func field for special3 lx opcodes (Cavium Octeon).
+ */
+enum lx_func {
+	lwx_op	= 0x00,
+	lhx_op	= 0x04,
+	lbux_op = 0x06,
+	ldx_op	= 0x08,
+	lwux_op = 0x10,
+	lhux_op = 0x14,
+	lbx_op	= 0x16,
+};
+
+/*
+ * BSHFL opcodes
+ */
+enum bshfl_func {
+	wsbh_op = 0x2,
+	seb_op  = 0x10,
+	seh_op  = 0x18,
+};
+
+/*
+ * DBSHFL opcodes
+ */
+enum dbshfl_func {
+	dsbh_op = 0x2,
+	dshd_op = 0x5,
+};
+
+/*
+ * MSA minor opcodes.
+ */
+enum msa_func {
+	msa_elm_op = 0x19,
+};
+
+/*
+ * MSA ELM opcodes.
+ */
+enum msa_elm {
+	msa_ctc_op = 0x3e,
+	msa_cfc_op = 0x7e,
+};
+
+/*
+ * func field for MSA MI10 format.
+ */
+enum msa_mi10_func {
+	msa_ld_op = 8,
+	msa_st_op = 9,
+};
+
+/*
+ * MSA 2 bit format fields.
+ */
+enum msa_2b_fmt {
+	msa_fmt_b = 0,
+	msa_fmt_h = 1,
+	msa_fmt_w = 2,
+	msa_fmt_d = 3,
+};
+
+/*
+ * (microMIPS) Major opcodes.
+ */
+enum mm_major_op {
+	mm_pool32a_op, mm_pool16a_op, mm_lbu16_op, mm_move16_op,
+	mm_addi32_op, mm_lbu32_op, mm_sb32_op, mm_lb32_op,
+	mm_pool32b_op, mm_pool16b_op, mm_lhu16_op, mm_andi16_op,
+	mm_addiu32_op, mm_lhu32_op, mm_sh32_op, mm_lh32_op,
+	mm_pool32i_op, mm_pool16c_op, mm_lwsp16_op, mm_pool16d_op,
+	mm_ori32_op, mm_pool32f_op, mm_pool32s_op, mm_reserved2_op,
+	mm_pool32c_op, mm_lwgp16_op, mm_lw16_op, mm_pool16e_op,
+	mm_xori32_op, mm_jals32_op, mm_addiupc_op, mm_reserved3_op,
+	mm_reserved4_op, mm_pool16f_op, mm_sb16_op, mm_beqz16_op,
+	mm_slti32_op, mm_beq32_op, mm_swc132_op, mm_lwc132_op,
+	mm_reserved5_op, mm_reserved6_op, mm_sh16_op, mm_bnez16_op,
+	mm_sltiu32_op, mm_bne32_op, mm_sdc132_op, mm_ldc132_op,
+	mm_reserved7_op, mm_reserved8_op, mm_swsp16_op, mm_b16_op,
+	mm_andi32_op, mm_j32_op, mm_sd32_op, mm_ld32_op,
+	mm_reserved11_op, mm_reserved12_op, mm_sw16_op, mm_li16_op,
+	mm_jalx32_op, mm_jal32_op, mm_sw32_op, mm_lw32_op,
+};
+
+/*
+ * (microMIPS) POOL32I minor opcodes.
+ */
+enum mm_32i_minor_op {
+	mm_bltz_op, mm_bltzal_op, mm_bgez_op, mm_bgezal_op,
+	mm_blez_op, mm_bnezc_op, mm_bgtz_op, mm_beqzc_op,
+	mm_tlti_op, mm_tgei_op, mm_tltiu_op, mm_tgeiu_op,
+	mm_tnei_op, mm_lui_op, mm_teqi_op, mm_reserved13_op,
+	mm_synci_op, mm_bltzals_op, mm_reserved14_op, mm_bgezals_op,
+	mm_bc2f_op, mm_bc2t_op, mm_reserved15_op, mm_reserved16_op,
+	mm_reserved17_op, mm_reserved18_op, mm_bposge64_op, mm_bposge32_op,
+	mm_bc1f_op, mm_bc1t_op, mm_reserved19_op, mm_reserved20_op,
+	mm_bc1any2f_op, mm_bc1any2t_op, mm_bc1any4f_op, mm_bc1any4t_op,
+};
+
+/*
+ * (microMIPS) POOL32A minor opcodes.
+ */
+enum mm_32a_minor_op {
+	mm_sll32_op = 0x000,
+	mm_ins_op = 0x00c,
+	mm_sllv32_op = 0x010,
+	mm_ext_op = 0x02c,
+	mm_pool32axf_op = 0x03c,
+	mm_srl32_op = 0x040,
+	mm_srlv32_op = 0x050,
+	mm_sra_op = 0x080,
+	mm_srav_op = 0x090,
+	mm_rotr_op = 0x0c0,
+	mm_lwxs_op = 0x118,
+	mm_addu32_op = 0x150,
+	mm_subu32_op = 0x1d0,
+	mm_wsbh_op = 0x1ec,
+	mm_mul_op = 0x210,
+	mm_and_op = 0x250,
+	mm_or32_op = 0x290,
+	mm_xor32_op = 0x310,
+	mm_slt_op = 0x350,
+	mm_sltu_op = 0x390,
+};
+
+/*
+ * (microMIPS) POOL32B functions.
+ */
+enum mm_32b_func {
+	mm_lwc2_func = 0x0,
+	mm_lwp_func = 0x1,
+	mm_ldc2_func = 0x2,
+	mm_ldp_func = 0x4,
+	mm_lwm32_func = 0x5,
+	mm_cache_func = 0x6,
+	mm_ldm_func = 0x7,
+	mm_swc2_func = 0x8,
+	mm_swp_func = 0x9,
+	mm_sdc2_func = 0xa,
+	mm_sdp_func = 0xc,
+	mm_swm32_func = 0xd,
+	mm_sdm_func = 0xf,
+};
+
+/*
+ * (microMIPS) POOL32C functions.
+ */
+enum mm_32c_func {
+	mm_pref_func = 0x2,
+	mm_ll_func = 0x3,
+	mm_swr_func = 0x9,
+	mm_sc_func = 0xb,
+	mm_lwu_func = 0xe,
+};
+
+/*
+ * (microMIPS) POOL32AXF minor opcodes.
+ */
+enum mm_32axf_minor_op {
+	mm_mfc0_op = 0x003,
+	mm_mtc0_op = 0x00b,
+	mm_tlbp_op = 0x00d,
+	mm_mfhi32_op = 0x035,
+	mm_jalr_op = 0x03c,
+	mm_tlbr_op = 0x04d,
+	mm_mflo32_op = 0x075,
+	mm_jalrhb_op = 0x07c,
+	mm_tlbwi_op = 0x08d,
+	mm_mthi32_op = 0x0b5,
+	mm_tlbwr_op = 0x0cd,
+	mm_mtlo32_op = 0x0f5,
+	mm_di_op = 0x11d,
+	mm_jalrs_op = 0x13c,
+	mm_jalrshb_op = 0x17c,
+	mm_sync_op = 0x1ad,
+	mm_syscall_op = 0x22d,
+	mm_wait_op = 0x24d,
+	mm_eret_op = 0x3cd,
+	mm_divu_op = 0x5dc,
+};
+
+/*
+ * (microMIPS) POOL32F minor opcodes.
+ */
+enum mm_32f_minor_op {
+	mm_32f_00_op = 0x00,
+	mm_32f_01_op = 0x01,
+	mm_32f_02_op = 0x02,
+	mm_32f_10_op = 0x08,
+	mm_32f_11_op = 0x09,
+	mm_32f_12_op = 0x0a,
+	mm_32f_20_op = 0x10,
+	mm_32f_30_op = 0x18,
+	mm_32f_40_op = 0x20,
+	mm_32f_41_op = 0x21,
+	mm_32f_42_op = 0x22,
+	mm_32f_50_op = 0x28,
+	mm_32f_51_op = 0x29,
+	mm_32f_52_op = 0x2a,
+	mm_32f_60_op = 0x30,
+	mm_32f_70_op = 0x38,
+	mm_32f_73_op = 0x3b,
+	mm_32f_74_op = 0x3c,
+};
+
+/*
+ * (microMIPS) POOL32F secondary minor opcodes.
+ */
+enum mm_32f_10_minor_op {
+	mm_lwxc1_op = 0x1,
+	mm_swxc1_op,
+	mm_ldxc1_op,
+	mm_sdxc1_op,
+	mm_luxc1_op,
+	mm_suxc1_op,
+};
+
+enum mm_32f_func {
+	mm_lwxc1_func = 0x048,
+	mm_swxc1_func = 0x088,
+	mm_ldxc1_func = 0x0c8,
+	mm_sdxc1_func = 0x108,
+};
+
+/*
+ * (microMIPS) POOL32F secondary minor opcodes.
+ */
+enum mm_32f_40_minor_op {
+	mm_fmovf_op,
+	mm_fmovt_op,
+};
+
+/*
+ * (microMIPS) POOL32F secondary minor opcodes.
+ */
+enum mm_32f_60_minor_op {
+	mm_fadd_op,
+	mm_fsub_op,
+	mm_fmul_op,
+	mm_fdiv_op,
+};
+
+/*
+ * (microMIPS) POOL32F secondary minor opcodes.
+ */
+enum mm_32f_70_minor_op {
+	mm_fmovn_op,
+	mm_fmovz_op,
+};
+
+/*
+ * (microMIPS) POOL32FXF secondary minor opcodes for POOL32F.
+ */
+enum mm_32f_73_minor_op {
+	mm_fmov0_op = 0x01,
+	mm_fcvtl_op = 0x04,
+	mm_movf0_op = 0x05,
+	mm_frsqrt_op = 0x08,
+	mm_ffloorl_op = 0x0c,
+	mm_fabs0_op = 0x0d,
+	mm_fcvtw_op = 0x24,
+	mm_movt0_op = 0x25,
+	mm_fsqrt_op = 0x28,
+	mm_ffloorw_op = 0x2c,
+	mm_fneg0_op = 0x2d,
+	mm_cfc1_op = 0x40,
+	mm_frecip_op = 0x48,
+	mm_fceill_op = 0x4c,
+	mm_fcvtd0_op = 0x4d,
+	mm_ctc1_op = 0x60,
+	mm_fceilw_op = 0x6c,
+	mm_fcvts0_op = 0x6d,
+	mm_mfc1_op = 0x80,
+	mm_fmov1_op = 0x81,
+	mm_movf1_op = 0x85,
+	mm_ftruncl_op = 0x8c,
+	mm_fabs1_op = 0x8d,
+	mm_mtc1_op = 0xa0,
+	mm_movt1_op = 0xa5,
+	mm_ftruncw_op = 0xac,
+	mm_fneg1_op = 0xad,
+	mm_mfhc1_op = 0xc0,
+	mm_froundl_op = 0xcc,
+	mm_fcvtd1_op = 0xcd,
+	mm_mthc1_op = 0xe0,
+	mm_froundw_op = 0xec,
+	mm_fcvts1_op = 0xed,
+};
+
+/*
+ * (microMIPS) POOL32S minor opcodes.
+ */
+enum mm_32s_minor_op {
+	mm_32s_elm_op = 0x16,
+};
+
+/*
+ * (microMIPS) POOL16C minor opcodes.
+ */
+enum mm_16c_minor_op {
+	mm_lwm16_op = 0x04,
+	mm_swm16_op = 0x05,
+	mm_jr16_op = 0x0c,
+	mm_jrc_op = 0x0d,
+	mm_jalr16_op = 0x0e,
+	mm_jalrs16_op = 0x0f,
+	mm_jraddiusp_op = 0x18,
+};
+
+/*
+ * (microMIPS) POOL16D minor opcodes.
+ */
+enum mm_16d_minor_op {
+	mm_addius5_func,
+	mm_addiusp_func,
+};
+
+/*
+ * (MIPS16e) opcodes.
+ */
+enum MIPS16e_ops {
+	MIPS16e_jal_op = 003,
+	MIPS16e_ld_op = 007,
+	MIPS16e_i8_op = 014,
+	MIPS16e_sd_op = 017,
+	MIPS16e_lb_op = 020,
+	MIPS16e_lh_op = 021,
+	MIPS16e_lwsp_op = 022,
+	MIPS16e_lw_op = 023,
+	MIPS16e_lbu_op = 024,
+	MIPS16e_lhu_op = 025,
+	MIPS16e_lwpc_op = 026,
+	MIPS16e_lwu_op = 027,
+	MIPS16e_sb_op = 030,
+	MIPS16e_sh_op = 031,
+	MIPS16e_swsp_op = 032,
+	MIPS16e_sw_op = 033,
+	MIPS16e_rr_op = 035,
+	MIPS16e_extend_op = 036,
+	MIPS16e_i64_op = 037,
+};
+
+enum MIPS16e_i64_func {
+	MIPS16e_ldsp_func,
+	MIPS16e_sdsp_func,
+	MIPS16e_sdrasp_func,
+	MIPS16e_dadjsp_func,
+	MIPS16e_ldpc_func,
+};
+
+enum MIPS16e_rr_func {
+	MIPS16e_jr_func,
+};
+
+enum MIPS6e_i8_func {
+	MIPS16e_swrasp_func = 02,
+};
+
+/*
+ * (microMIPS) NOP instruction.
+ */
+#define MM_NOP16	0x0c00
+
+struct j_format {
+	__BITFIELD_FIELD(unsigned int opcode : 6, /* Jump format */
+	__BITFIELD_FIELD(unsigned int target : 26,
+	;))
+};
+
+struct i_format {			/* signed immediate format */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int rs : 5,
+	__BITFIELD_FIELD(unsigned int rt : 5,
+	__BITFIELD_FIELD(signed int simmediate : 16,
+	;))))
+};
+
+struct u_format {			/* unsigned immediate format */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int rs : 5,
+	__BITFIELD_FIELD(unsigned int rt : 5,
+	__BITFIELD_FIELD(unsigned int uimmediate : 16,
+	;))))
+};
+
+struct c_format {			/* Cache (>= R6000) format */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int rs : 5,
+	__BITFIELD_FIELD(unsigned int c_op : 3,
+	__BITFIELD_FIELD(unsigned int cache : 2,
+	__BITFIELD_FIELD(unsigned int simmediate : 16,
+	;)))))
+};
+
+struct r_format {			/* Register format */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int rs : 5,
+	__BITFIELD_FIELD(unsigned int rt : 5,
+	__BITFIELD_FIELD(unsigned int rd : 5,
+	__BITFIELD_FIELD(unsigned int re : 5,
+	__BITFIELD_FIELD(unsigned int func : 6,
+	;))))))
+};
+
+struct c0r_format {			/* C0 register format */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int rs : 5,
+	__BITFIELD_FIELD(unsigned int rt : 5,
+	__BITFIELD_FIELD(unsigned int rd : 5,
+	__BITFIELD_FIELD(unsigned int z: 8,
+	__BITFIELD_FIELD(unsigned int sel : 3,
+	;))))))
+};
+
+struct mfmc0_format {			/* MFMC0 register format */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int rs : 5,
+	__BITFIELD_FIELD(unsigned int rt : 5,
+	__BITFIELD_FIELD(unsigned int rd : 5,
+	__BITFIELD_FIELD(unsigned int re : 5,
+	__BITFIELD_FIELD(unsigned int sc : 1,
+	__BITFIELD_FIELD(unsigned int : 2,
+	__BITFIELD_FIELD(unsigned int sel : 3,
+	;))))))))
+};
+
+struct co_format {			/* C0 CO format */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int co : 1,
+	__BITFIELD_FIELD(unsigned int code : 19,
+	__BITFIELD_FIELD(unsigned int func : 6,
+	;))))
+};
+
+struct p_format {		/* Performance counter format (R10000) */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int rs : 5,
+	__BITFIELD_FIELD(unsigned int rt : 5,
+	__BITFIELD_FIELD(unsigned int rd : 5,
+	__BITFIELD_FIELD(unsigned int re : 5,
+	__BITFIELD_FIELD(unsigned int func : 6,
+	;))))))
+};
+
+struct f_format {			/* FPU register format */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int : 1,
+	__BITFIELD_FIELD(unsigned int fmt : 4,
+	__BITFIELD_FIELD(unsigned int rt : 5,
+	__BITFIELD_FIELD(unsigned int rd : 5,
+	__BITFIELD_FIELD(unsigned int re : 5,
+	__BITFIELD_FIELD(unsigned int func : 6,
+	;)))))))
+};
+
+struct ma_format {		/* FPU multiply and add format (MIPS IV) */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int fr : 5,
+	__BITFIELD_FIELD(unsigned int ft : 5,
+	__BITFIELD_FIELD(unsigned int fs : 5,
+	__BITFIELD_FIELD(unsigned int fd : 5,
+	__BITFIELD_FIELD(unsigned int func : 4,
+	__BITFIELD_FIELD(unsigned int fmt : 2,
+	;)))))))
+};
+
+struct b_format {			/* BREAK and SYSCALL */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int code : 20,
+	__BITFIELD_FIELD(unsigned int func : 6,
+	;)))
+};
+
+struct ps_format {			/* MIPS-3D / paired single format */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int rs : 5,
+	__BITFIELD_FIELD(unsigned int ft : 5,
+	__BITFIELD_FIELD(unsigned int fs : 5,
+	__BITFIELD_FIELD(unsigned int fd : 5,
+	__BITFIELD_FIELD(unsigned int func : 6,
+	;))))))
+};
+
+struct v_format {				/* MDMX vector format */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int sel : 4,
+	__BITFIELD_FIELD(unsigned int fmt : 1,
+	__BITFIELD_FIELD(unsigned int vt : 5,
+	__BITFIELD_FIELD(unsigned int vs : 5,
+	__BITFIELD_FIELD(unsigned int vd : 5,
+	__BITFIELD_FIELD(unsigned int func : 6,
+	;)))))))
+};
+
+struct msa_mi10_format {		/* MSA MI10 */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(signed int s10 : 10,
+	__BITFIELD_FIELD(unsigned int rs : 5,
+	__BITFIELD_FIELD(unsigned int wd : 5,
+	__BITFIELD_FIELD(unsigned int func : 4,
+	__BITFIELD_FIELD(unsigned int df : 2,
+	;))))))
+};
+
+struct dsp_format {		/* SPEC3 DSP format instructions */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int base : 5,
+	__BITFIELD_FIELD(unsigned int index : 5,
+	__BITFIELD_FIELD(unsigned int rd : 5,
+	__BITFIELD_FIELD(unsigned int op : 5,
+	__BITFIELD_FIELD(unsigned int func : 6,
+	;))))))
+};
+
+struct spec3_format {   /* SPEC3 */
+	__BITFIELD_FIELD(unsigned int opcode:6,
+	__BITFIELD_FIELD(unsigned int rs:5,
+	__BITFIELD_FIELD(unsigned int rt:5,
+	__BITFIELD_FIELD(signed int simmediate:9,
+	__BITFIELD_FIELD(unsigned int func:7,
+	;)))))
+};
+
+/*
+ * microMIPS instruction formats (32-bit length)
+ *
+ * NOTE:
+ *	Parenthesis denote whether the format is a microMIPS instruction or
+ *	if it is MIPS32 instruction re-encoded for use in the microMIPS ASE.
+ */
+struct fb_format {		/* FPU branch format (MIPS32) */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int bc : 5,
+	__BITFIELD_FIELD(unsigned int cc : 3,
+	__BITFIELD_FIELD(unsigned int flag : 2,
+	__BITFIELD_FIELD(signed int simmediate : 16,
+	;)))))
+};
+
+struct fp0_format {		/* FPU multiply and add format (MIPS32) */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int fmt : 5,
+	__BITFIELD_FIELD(unsigned int ft : 5,
+	__BITFIELD_FIELD(unsigned int fs : 5,
+	__BITFIELD_FIELD(unsigned int fd : 5,
+	__BITFIELD_FIELD(unsigned int func : 6,
+	;))))))
+};
+
+struct mm_fp0_format {		/* FPU multiply and add format (microMIPS) */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int ft : 5,
+	__BITFIELD_FIELD(unsigned int fs : 5,
+	__BITFIELD_FIELD(unsigned int fd : 5,
+	__BITFIELD_FIELD(unsigned int fmt : 3,
+	__BITFIELD_FIELD(unsigned int op : 2,
+	__BITFIELD_FIELD(unsigned int func : 6,
+	;)))))))
+};
+
+struct fp1_format {		/* FPU mfc1 and cfc1 format (MIPS32) */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int op : 5,
+	__BITFIELD_FIELD(unsigned int rt : 5,
+	__BITFIELD_FIELD(unsigned int fs : 5,
+	__BITFIELD_FIELD(unsigned int fd : 5,
+	__BITFIELD_FIELD(unsigned int func : 6,
+	;))))))
+};
+
+struct mm_fp1_format {		/* FPU mfc1 and cfc1 format (microMIPS) */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int rt : 5,
+	__BITFIELD_FIELD(unsigned int fs : 5,
+	__BITFIELD_FIELD(unsigned int fmt : 2,
+	__BITFIELD_FIELD(unsigned int op : 8,
+	__BITFIELD_FIELD(unsigned int func : 6,
+	;))))))
+};
+
+struct mm_fp2_format {		/* FPU movt and movf format (microMIPS) */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int fd : 5,
+	__BITFIELD_FIELD(unsigned int fs : 5,
+	__BITFIELD_FIELD(unsigned int cc : 3,
+	__BITFIELD_FIELD(unsigned int zero : 2,
+	__BITFIELD_FIELD(unsigned int fmt : 2,
+	__BITFIELD_FIELD(unsigned int op : 3,
+	__BITFIELD_FIELD(unsigned int func : 6,
+	;))))))))
+};
+
+struct mm_fp3_format {		/* FPU abs and neg format (microMIPS) */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int rt : 5,
+	__BITFIELD_FIELD(unsigned int fs : 5,
+	__BITFIELD_FIELD(unsigned int fmt : 3,
+	__BITFIELD_FIELD(unsigned int op : 7,
+	__BITFIELD_FIELD(unsigned int func : 6,
+	;))))))
+};
+
+struct mm_fp4_format {		/* FPU c.cond format (microMIPS) */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int rt : 5,
+	__BITFIELD_FIELD(unsigned int fs : 5,
+	__BITFIELD_FIELD(unsigned int cc : 3,
+	__BITFIELD_FIELD(unsigned int fmt : 3,
+	__BITFIELD_FIELD(unsigned int cond : 4,
+	__BITFIELD_FIELD(unsigned int func : 6,
+	;)))))))
+};
+
+struct mm_fp5_format {		/* FPU lwxc1 and swxc1 format (microMIPS) */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int index : 5,
+	__BITFIELD_FIELD(unsigned int base : 5,
+	__BITFIELD_FIELD(unsigned int fd : 5,
+	__BITFIELD_FIELD(unsigned int op : 5,
+	__BITFIELD_FIELD(unsigned int func : 6,
+	;))))))
+};
+
+struct fp6_format {		/* FPU madd and msub format (MIPS IV) */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int fr : 5,
+	__BITFIELD_FIELD(unsigned int ft : 5,
+	__BITFIELD_FIELD(unsigned int fs : 5,
+	__BITFIELD_FIELD(unsigned int fd : 5,
+	__BITFIELD_FIELD(unsigned int func : 6,
+	;))))))
+};
+
+struct mm_fp6_format {		/* FPU madd and msub format (microMIPS) */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int ft : 5,
+	__BITFIELD_FIELD(unsigned int fs : 5,
+	__BITFIELD_FIELD(unsigned int fd : 5,
+	__BITFIELD_FIELD(unsigned int fr : 5,
+	__BITFIELD_FIELD(unsigned int func : 6,
+	;))))))
+};
+
+struct mm_i_format {		/* Immediate format (microMIPS) */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int rt : 5,
+	__BITFIELD_FIELD(unsigned int rs : 5,
+	__BITFIELD_FIELD(signed int simmediate : 16,
+	;))))
+};
+
+struct mm_m_format {		/* Multi-word load/store format (microMIPS) */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int rd : 5,
+	__BITFIELD_FIELD(unsigned int base : 5,
+	__BITFIELD_FIELD(unsigned int func : 4,
+	__BITFIELD_FIELD(signed int simmediate : 12,
+	;)))))
+};
+
+struct mm_x_format {		/* Scaled indexed load format (microMIPS) */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int index : 5,
+	__BITFIELD_FIELD(unsigned int base : 5,
+	__BITFIELD_FIELD(unsigned int rd : 5,
+	__BITFIELD_FIELD(unsigned int func : 11,
+	;)))))
+};
+
+struct mm_a_format {		/* ADDIUPC format (microMIPS) */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int rs : 3,
+	__BITFIELD_FIELD(signed int simmediate : 23,
+	;)))
+};
+
+/*
+ * microMIPS instruction formats (16-bit length)
+ */
+struct mm_b0_format {		/* Unconditional branch format (microMIPS) */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(signed int simmediate : 10,
+	__BITFIELD_FIELD(unsigned int : 16, /* Ignored */
+	;)))
+};
+
+struct mm_b1_format {		/* Conditional branch format (microMIPS) */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int rs : 3,
+	__BITFIELD_FIELD(signed int simmediate : 7,
+	__BITFIELD_FIELD(unsigned int : 16, /* Ignored */
+	;))))
+};
+
+struct mm16_m_format {		/* Multi-word load/store format */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int func : 4,
+	__BITFIELD_FIELD(unsigned int rlist : 2,
+	__BITFIELD_FIELD(unsigned int imm : 4,
+	__BITFIELD_FIELD(unsigned int : 16, /* Ignored */
+	;)))))
+};
+
+struct mm16_rb_format {		/* Signed immediate format */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int rt : 3,
+	__BITFIELD_FIELD(unsigned int base : 3,
+	__BITFIELD_FIELD(signed int simmediate : 4,
+	__BITFIELD_FIELD(unsigned int : 16, /* Ignored */
+	;)))))
+};
+
+struct mm16_r3_format {		/* Load from global pointer format */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int rt : 3,
+	__BITFIELD_FIELD(signed int simmediate : 7,
+	__BITFIELD_FIELD(unsigned int : 16, /* Ignored */
+	;))))
+};
+
+struct mm16_r5_format {		/* Load/store from stack pointer format */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int rt : 5,
+	__BITFIELD_FIELD(unsigned int imm : 5,
+	__BITFIELD_FIELD(unsigned int : 16, /* Ignored */
+	;))))
+};
+
+/*
+ * Loongson-3 overridden COP2 instruction formats (32-bit length)
+ */
+struct loongson3_lswc2_format {	/* Loongson-3 overridden lwc2/swc2 Load/Store format */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int base : 5,
+	__BITFIELD_FIELD(unsigned int rt : 5,
+	__BITFIELD_FIELD(unsigned int fr : 1,
+	__BITFIELD_FIELD(unsigned int offset : 9,
+	__BITFIELD_FIELD(unsigned int ls : 1,
+	__BITFIELD_FIELD(unsigned int rq : 5,
+	;)))))))
+};
+
+struct loongson3_lsdc2_format {	/* Loongson-3 overridden ldc2/sdc2 Load/Store format */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int base : 5,
+	__BITFIELD_FIELD(unsigned int rt : 5,
+	__BITFIELD_FIELD(unsigned int index : 5,
+	__BITFIELD_FIELD(unsigned int offset : 8,
+	__BITFIELD_FIELD(unsigned int opcode1 : 3,
+	;))))))
+};
+
+struct loongson3_lscsr_format {	/* Loongson-3 CPUCFG&CSR read/write format */
+	__BITFIELD_FIELD(unsigned int opcode : 6,
+	__BITFIELD_FIELD(unsigned int rs : 5,
+	__BITFIELD_FIELD(unsigned int fr : 5,
+	__BITFIELD_FIELD(unsigned int rd : 5,
+	__BITFIELD_FIELD(unsigned int fd : 5,
+	__BITFIELD_FIELD(unsigned int func : 6,
+	;))))))
+};
+
+/*
+ * MIPS16e instruction formats (16-bit length)
+ */
+struct m16e_rr {
+	__BITFIELD_FIELD(unsigned int opcode : 5,
+	__BITFIELD_FIELD(unsigned int rx : 3,
+	__BITFIELD_FIELD(unsigned int nd : 1,
+	__BITFIELD_FIELD(unsigned int l : 1,
+	__BITFIELD_FIELD(unsigned int ra : 1,
+	__BITFIELD_FIELD(unsigned int func : 5,
+	;))))))
+};
+
+struct m16e_jal {
+	__BITFIELD_FIELD(unsigned int opcode : 5,
+	__BITFIELD_FIELD(unsigned int x : 1,
+	__BITFIELD_FIELD(unsigned int imm20_16 : 5,
+	__BITFIELD_FIELD(signed int imm25_21 : 5,
+	;))))
+};
+
+struct m16e_i64 {
+	__BITFIELD_FIELD(unsigned int opcode : 5,
+	__BITFIELD_FIELD(unsigned int func : 3,
+	__BITFIELD_FIELD(unsigned int imm : 8,
+	;)))
+};
+
+struct m16e_ri64 {
+	__BITFIELD_FIELD(unsigned int opcode : 5,
+	__BITFIELD_FIELD(unsigned int func : 3,
+	__BITFIELD_FIELD(unsigned int ry : 3,
+	__BITFIELD_FIELD(unsigned int imm : 5,
+	;))))
+};
+
+struct m16e_ri {
+	__BITFIELD_FIELD(unsigned int opcode : 5,
+	__BITFIELD_FIELD(unsigned int rx : 3,
+	__BITFIELD_FIELD(unsigned int imm : 8,
+	;)))
+};
+
+struct m16e_rri {
+	__BITFIELD_FIELD(unsigned int opcode : 5,
+	__BITFIELD_FIELD(unsigned int rx : 3,
+	__BITFIELD_FIELD(unsigned int ry : 3,
+	__BITFIELD_FIELD(unsigned int imm : 5,
+	;))))
+};
+
+struct m16e_i8 {
+	__BITFIELD_FIELD(unsigned int opcode : 5,
+	__BITFIELD_FIELD(unsigned int func : 3,
+	__BITFIELD_FIELD(unsigned int imm : 8,
+	;)))
+};
+
+union mips_instruction {
+	unsigned int word;
+	unsigned short halfword[2];
+	unsigned char byte[4];
+	struct j_format j_format;
+	struct i_format i_format;
+	struct u_format u_format;
+	struct c_format c_format;
+	struct r_format r_format;
+	struct c0r_format c0r_format;
+	struct mfmc0_format mfmc0_format;
+	struct co_format co_format;
+	struct p_format p_format;
+	struct f_format f_format;
+	struct ma_format ma_format;
+	struct msa_mi10_format msa_mi10_format;
+	struct b_format b_format;
+	struct ps_format ps_format;
+	struct v_format v_format;
+	struct dsp_format dsp_format;
+	struct spec3_format spec3_format;
+	struct fb_format fb_format;
+	struct fp0_format fp0_format;
+	struct mm_fp0_format mm_fp0_format;
+	struct fp1_format fp1_format;
+	struct mm_fp1_format mm_fp1_format;
+	struct mm_fp2_format mm_fp2_format;
+	struct mm_fp3_format mm_fp3_format;
+	struct mm_fp4_format mm_fp4_format;
+	struct mm_fp5_format mm_fp5_format;
+	struct fp6_format fp6_format;
+	struct mm_fp6_format mm_fp6_format;
+	struct mm_i_format mm_i_format;
+	struct mm_m_format mm_m_format;
+	struct mm_x_format mm_x_format;
+	struct mm_a_format mm_a_format;
+	struct mm_b0_format mm_b0_format;
+	struct mm_b1_format mm_b1_format;
+	struct mm16_m_format mm16_m_format ;
+	struct mm16_rb_format mm16_rb_format;
+	struct mm16_r3_format mm16_r3_format;
+	struct mm16_r5_format mm16_r5_format;
+	struct loongson3_lswc2_format loongson3_lswc2_format;
+	struct loongson3_lsdc2_format loongson3_lsdc2_format;
+	struct loongson3_lscsr_format loongson3_lscsr_format;
+};
+
+union mips16e_instruction {
+	unsigned int full : 16;
+	struct m16e_rr rr;
+	struct m16e_jal jal;
+	struct m16e_i64 i64;
+	struct m16e_ri64 ri64;
+	struct m16e_ri ri;
+	struct m16e_rri rri;
+	struct m16e_i8 i8;
+};
+
+#endif /* _UAPI_ASM_INST_H */
diff --git a/arch/mips/include/uapi/asm/ioctl.h b/arch/mips/include/uapi/asm/ioctl.h
new file mode 100644
index 000000000..1050a6ea2
--- /dev/null
+++ b/arch/mips/include/uapi/asm/ioctl.h
@@ -0,0 +1,28 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995, 96, 99, 2001 Ralf Baechle <ralf@linux-mips.org>
+ * Copyright (C) 2009 Wind River Systems
+ * Written by Ralf Baechle <ralf@linux-mips.org>
+ */
+#ifndef __ASM_IOCTL_H
+#define __ASM_IOCTL_H
+
+#define _IOC_SIZEBITS	13
+#define _IOC_DIRBITS	3
+
+/*
+ * Direction bits _IOC_NONE could be 0, but OSF/1 gives it a bit.
+ * And this turns out useful to catch old ioctl numbers in header
+ * files for us.
+ */
+#define _IOC_NONE	1U
+#define _IOC_READ	2U
+#define _IOC_WRITE	4U
+
+#include <asm-generic/ioctl.h>
+
+#endif /* __ASM_IOCTL_H */
diff --git a/arch/mips/include/uapi/asm/ioctls.h b/arch/mips/include/uapi/asm/ioctls.h
new file mode 100644
index 000000000..16aa8a766
--- /dev/null
+++ b/arch/mips/include/uapi/asm/ioctls.h
@@ -0,0 +1,119 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995, 1996, 2001 Ralf Baechle
+ * Copyright (C) 2001 MIPS Technologies, Inc.
+ */
+#ifndef __ASM_IOCTLS_H
+#define __ASM_IOCTLS_H
+
+#include <asm/ioctl.h>
+
+#define TCGETA		0x5401
+#define TCSETA		0x5402	/* Clashes with SNDCTL_TMR_START sound ioctl */
+#define TCSETAW		0x5403
+#define TCSETAF		0x5404
+
+#define TCSBRK		0x5405
+#define TCXONC		0x5406
+#define TCFLSH		0x5407
+
+#define TCGETS		0x540d
+#define TCSETS		0x540e
+#define TCSETSW		0x540f
+#define TCSETSF		0x5410
+
+#define TIOCEXCL	0x740d		/* set exclusive use of tty */
+#define TIOCNXCL	0x740e		/* reset exclusive use of tty */
+#define TIOCOUTQ	0x7472		/* output queue size */
+#define TIOCSTI		0x5472		/* simulate terminal input */
+#define TIOCMGET	0x741d		/* get all modem bits */
+#define TIOCMBIS	0x741b		/* bis modem bits */
+#define TIOCMBIC	0x741c		/* bic modem bits */
+#define TIOCMSET	0x741a		/* set all modem bits */
+#define TIOCPKT		0x5470		/* pty: set/clear packet mode */
+#define	 TIOCPKT_DATA		0x00	/* data packet */
+#define	 TIOCPKT_FLUSHREAD	0x01	/* flush packet */
+#define	 TIOCPKT_FLUSHWRITE	0x02	/* flush packet */
+#define	 TIOCPKT_STOP		0x04	/* stop output */
+#define	 TIOCPKT_START		0x08	/* start output */
+#define	 TIOCPKT_NOSTOP		0x10	/* no more ^S, ^Q */
+#define	 TIOCPKT_DOSTOP		0x20	/* now do ^S ^Q */
+#define	 TIOCPKT_IOCTL		0x40	/* state change of pty driver */
+#define TIOCSWINSZ	_IOW('t', 103, struct winsize)	/* set window size */
+#define TIOCGWINSZ	_IOR('t', 104, struct winsize)	/* get window size */
+#define TIOCNOTTY	0x5471		/* void tty association */
+#define TIOCSETD	0x7401
+#define TIOCGETD	0x7400
+
+#define FIOCLEX		0x6601
+#define FIONCLEX	0x6602
+#define FIOASYNC	0x667d
+#define FIONBIO		0x667e
+#define FIOQSIZE	0x667f
+
+#define TIOCGLTC	0x7474			/* get special local chars */
+#define TIOCSLTC	0x7475			/* set special local chars */
+#define TIOCSPGRP	_IOW('t', 118, int)	/* set pgrp of tty */
+#define TIOCGPGRP	_IOR('t', 119, int)	/* get pgrp of tty */
+#define TIOCCONS	_IOW('t', 120, int)	/* become virtual console */
+
+#define FIONREAD	0x467f
+#define TIOCINQ		FIONREAD
+
+#define TIOCGETP	0x7408
+#define TIOCSETP	0x7409
+#define TIOCSETN	0x740a			/* TIOCSETP wo flush */
+
+/* #define TIOCSETA	_IOW('t', 20, struct termios) set termios struct */
+/* #define TIOCSETAW	_IOW('t', 21, struct termios) drain output, set */
+/* #define TIOCSETAF	_IOW('t', 22, struct termios) drn out, fls in, set */
+/* #define TIOCGETD	_IOR('t', 26, int)	get line discipline */
+/* #define TIOCSETD	_IOW('t', 27, int)	set line discipline */
+						/* 127-124 compat */
+
+#define TIOCSBRK	0x5427	/* BSD compatibility */
+#define TIOCCBRK	0x5428	/* BSD compatibility */
+#define TIOCGSID	0x7416	/* Return the session ID of FD */
+#define TCGETS2		_IOR('T', 0x2A, struct termios2)
+#define TCSETS2		_IOW('T', 0x2B, struct termios2)
+#define TCSETSW2	_IOW('T', 0x2C, struct termios2)
+#define TCSETSF2	_IOW('T', 0x2D, struct termios2)
+#define TIOCGRS485	_IOR('T', 0x2E, struct serial_rs485)
+#define TIOCSRS485	_IOWR('T', 0x2F, struct serial_rs485)
+#define TIOCGPTN	_IOR('T', 0x30, unsigned int) /* Get Pty Number (of pty-mux device) */
+#define TIOCSPTLCK	_IOW('T', 0x31, int)  /* Lock/unlock Pty */
+#define TIOCGDEV	_IOR('T', 0x32, unsigned int) /* Get primary device node of /dev/console */
+#define TIOCSIG		_IOW('T', 0x36, int)  /* Generate signal on Pty slave */
+#define TIOCVHANGUP	0x5437
+#define TIOCGPKT	_IOR('T', 0x38, int) /* Get packet mode state */
+#define TIOCGPTLCK	_IOR('T', 0x39, int) /* Get Pty lock state */
+#define TIOCGEXCL	_IOR('T', 0x40, int) /* Get exclusive mode state */
+#define TIOCGPTPEER	_IO('T', 0x41) /* Safely open the slave */
+#define TIOCGISO7816	_IOR('T', 0x42, struct serial_iso7816)
+#define TIOCSISO7816	_IOWR('T', 0x43, struct serial_iso7816)
+
+/* I hope the range from 0x5480 on is free ... */
+#define TIOCSCTTY	0x5480		/* become controlling tty */
+#define TIOCGSOFTCAR	0x5481
+#define TIOCSSOFTCAR	0x5482
+#define TIOCLINUX	0x5483
+#define TIOCGSERIAL	0x5484
+#define TIOCSSERIAL	0x5485
+#define TCSBRKP		0x5486	/* Needed for POSIX tcsendbreak() */
+#define TIOCSERCONFIG	0x5488
+#define TIOCSERGWILD	0x5489
+#define TIOCSERSWILD	0x548a
+#define TIOCGLCKTRMIOS	0x548b
+#define TIOCSLCKTRMIOS	0x548c
+#define TIOCSERGSTRUCT	0x548d /* For debugging only */
+#define TIOCSERGETLSR	0x548e /* Get line status register */
+#define TIOCSERGETMULTI 0x548f /* Get multiport config	*/
+#define TIOCSERSETMULTI 0x5490 /* Set multiport config */
+#define TIOCMIWAIT	0x5491 /* wait for a change on serial input line(s) */
+#define TIOCGICOUNT	0x5492 /* read serial port inline interrupt counts */
+
+#endif /* __ASM_IOCTLS_H */
diff --git a/arch/mips/include/uapi/asm/kvm.h b/arch/mips/include/uapi/asm/kvm.h
new file mode 100644
index 000000000..edcf717c4
--- /dev/null
+++ b/arch/mips/include/uapi/asm/kvm.h
@@ -0,0 +1,227 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2012  MIPS Technologies, Inc.  All rights reserved.
+ * Copyright (C) 2013 Cavium, Inc.
+ * Authors: Sanjay Lal <sanjayl@kymasys.com>
+ */
+
+#ifndef __LINUX_KVM_MIPS_H
+#define __LINUX_KVM_MIPS_H
+
+#include <linux/types.h>
+
+/*
+ * KVM MIPS specific structures and definitions.
+ *
+ * Some parts derived from the x86 version of this file.
+ */
+
+#define __KVM_HAVE_READONLY_MEM
+
+#define KVM_COALESCED_MMIO_PAGE_OFFSET 1
+
+/*
+ * for KVM_GET_REGS and KVM_SET_REGS
+ *
+ * If Config[AT] is zero (32-bit CPU), the register contents are
+ * stored in the lower 32-bits of the struct kvm_regs fields and sign
+ * extended to 64-bits.
+ */
+struct kvm_regs {
+	/* out (KVM_GET_REGS) / in (KVM_SET_REGS) */
+	__u64 gpr[32];
+	__u64 hi;
+	__u64 lo;
+	__u64 pc;
+};
+
+/*
+ * for KVM_GET_FPU and KVM_SET_FPU
+ */
+struct kvm_fpu {
+};
+
+
+/*
+ * For MIPS, we use KVM_SET_ONE_REG and KVM_GET_ONE_REG to access various
+ * registers.  The id field is broken down as follows:
+ *
+ *  bits[63..52] - As per linux/kvm.h
+ *  bits[51..32] - Must be zero.
+ *  bits[31..16] - Register set.
+ *
+ * Register set = 0: GP registers from kvm_regs (see definitions below).
+ *
+ * Register set = 1: CP0 registers.
+ *  bits[15..8]  - COP0 register set.
+ *
+ *  COP0 register set = 0: Main CP0 registers.
+ *   bits[7..3]   - Register 'rd'  index.
+ *   bits[2..0]   - Register 'sel' index.
+ *
+ *  COP0 register set = 1: MAARs.
+ *   bits[7..0]   - MAAR index.
+ *
+ * Register set = 2: KVM specific registers (see definitions below).
+ *
+ * Register set = 3: FPU / MSA registers (see definitions below).
+ *
+ * Other sets registers may be added in the future.  Each set would
+ * have its own identifier in bits[31..16].
+ */
+
+#define KVM_REG_MIPS_GP		(KVM_REG_MIPS | 0x0000000000000000ULL)
+#define KVM_REG_MIPS_CP0	(KVM_REG_MIPS | 0x0000000000010000ULL)
+#define KVM_REG_MIPS_KVM	(KVM_REG_MIPS | 0x0000000000020000ULL)
+#define KVM_REG_MIPS_FPU	(KVM_REG_MIPS | 0x0000000000030000ULL)
+
+
+/*
+ * KVM_REG_MIPS_GP - General purpose registers from kvm_regs.
+ */
+
+#define KVM_REG_MIPS_R0		(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 |  0)
+#define KVM_REG_MIPS_R1		(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 |  1)
+#define KVM_REG_MIPS_R2		(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 |  2)
+#define KVM_REG_MIPS_R3		(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 |  3)
+#define KVM_REG_MIPS_R4		(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 |  4)
+#define KVM_REG_MIPS_R5		(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 |  5)
+#define KVM_REG_MIPS_R6		(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 |  6)
+#define KVM_REG_MIPS_R7		(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 |  7)
+#define KVM_REG_MIPS_R8		(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 |  8)
+#define KVM_REG_MIPS_R9		(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 |  9)
+#define KVM_REG_MIPS_R10	(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 | 10)
+#define KVM_REG_MIPS_R11	(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 | 11)
+#define KVM_REG_MIPS_R12	(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 | 12)
+#define KVM_REG_MIPS_R13	(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 | 13)
+#define KVM_REG_MIPS_R14	(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 | 14)
+#define KVM_REG_MIPS_R15	(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 | 15)
+#define KVM_REG_MIPS_R16	(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 | 16)
+#define KVM_REG_MIPS_R17	(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 | 17)
+#define KVM_REG_MIPS_R18	(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 | 18)
+#define KVM_REG_MIPS_R19	(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 | 19)
+#define KVM_REG_MIPS_R20	(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 | 20)
+#define KVM_REG_MIPS_R21	(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 | 21)
+#define KVM_REG_MIPS_R22	(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 | 22)
+#define KVM_REG_MIPS_R23	(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 | 23)
+#define KVM_REG_MIPS_R24	(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 | 24)
+#define KVM_REG_MIPS_R25	(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 | 25)
+#define KVM_REG_MIPS_R26	(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 | 26)
+#define KVM_REG_MIPS_R27	(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 | 27)
+#define KVM_REG_MIPS_R28	(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 | 28)
+#define KVM_REG_MIPS_R29	(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 | 29)
+#define KVM_REG_MIPS_R30	(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 | 30)
+#define KVM_REG_MIPS_R31	(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 | 31)
+
+#define KVM_REG_MIPS_HI		(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 | 32)
+#define KVM_REG_MIPS_LO		(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 | 33)
+#define KVM_REG_MIPS_PC		(KVM_REG_MIPS_GP | KVM_REG_SIZE_U64 | 34)
+
+
+/*
+ * KVM_REG_MIPS_CP0 - Coprocessor 0 registers.
+ */
+
+#define KVM_REG_MIPS_MAAR	(KVM_REG_MIPS_CP0 | (1 << 8))
+#define KVM_REG_MIPS_CP0_MAAR(n)	(KVM_REG_MIPS_MAAR | \
+					 KVM_REG_SIZE_U64 | (n))
+
+
+/*
+ * KVM_REG_MIPS_KVM - KVM specific control registers.
+ */
+
+/*
+ * CP0_Count control
+ * DC:    Set 0: Master disable CP0_Count and set COUNT_RESUME to now
+ *        Set 1: Master re-enable CP0_Count with unchanged bias, handling timer
+ *               interrupts since COUNT_RESUME
+ *        This can be used to freeze the timer to get a consistent snapshot of
+ *        the CP0_Count and timer interrupt pending state, while also resuming
+ *        safely without losing time or guest timer interrupts.
+ * Other: Reserved, do not change.
+ */
+#define KVM_REG_MIPS_COUNT_CTL	    (KVM_REG_MIPS_KVM | KVM_REG_SIZE_U64 | 0)
+#define KVM_REG_MIPS_COUNT_CTL_DC	0x00000001
+
+/*
+ * CP0_Count resume monotonic nanoseconds
+ * The monotonic nanosecond time of the last set of COUNT_CTL.DC (master
+ * disable). Any reads and writes of Count related registers while
+ * COUNT_CTL.DC=1 will appear to occur at this time. When COUNT_CTL.DC is
+ * cleared again (master enable) any timer interrupts since this time will be
+ * emulated.
+ * Modifications to times in the future are rejected.
+ */
+#define KVM_REG_MIPS_COUNT_RESUME   (KVM_REG_MIPS_KVM | KVM_REG_SIZE_U64 | 1)
+/*
+ * CP0_Count rate in Hz
+ * Specifies the rate of the CP0_Count timer in Hz. Modifications occur without
+ * discontinuities in CP0_Count.
+ */
+#define KVM_REG_MIPS_COUNT_HZ	    (KVM_REG_MIPS_KVM | KVM_REG_SIZE_U64 | 2)
+
+
+/*
+ * KVM_REG_MIPS_FPU - Floating Point and MIPS SIMD Architecture (MSA) registers.
+ *
+ *  bits[15..8]  - Register subset (see definitions below).
+ *  bits[7..5]   - Must be zero.
+ *  bits[4..0]   - Register number within register subset.
+ */
+
+#define KVM_REG_MIPS_FPR	(KVM_REG_MIPS_FPU | 0x0000000000000000ULL)
+#define KVM_REG_MIPS_FCR	(KVM_REG_MIPS_FPU | 0x0000000000000100ULL)
+#define KVM_REG_MIPS_MSACR	(KVM_REG_MIPS_FPU | 0x0000000000000200ULL)
+
+/*
+ * KVM_REG_MIPS_FPR - Floating point / Vector registers.
+ */
+#define KVM_REG_MIPS_FPR_32(n)	(KVM_REG_MIPS_FPR | KVM_REG_SIZE_U32  | (n))
+#define KVM_REG_MIPS_FPR_64(n)	(KVM_REG_MIPS_FPR | KVM_REG_SIZE_U64  | (n))
+#define KVM_REG_MIPS_VEC_128(n)	(KVM_REG_MIPS_FPR | KVM_REG_SIZE_U128 | (n))
+
+/*
+ * KVM_REG_MIPS_FCR - Floating point control registers.
+ */
+#define KVM_REG_MIPS_FCR_IR	(KVM_REG_MIPS_FCR | KVM_REG_SIZE_U32 |  0)
+#define KVM_REG_MIPS_FCR_CSR	(KVM_REG_MIPS_FCR | KVM_REG_SIZE_U32 | 31)
+
+/*
+ * KVM_REG_MIPS_MSACR - MIPS SIMD Architecture (MSA) control registers.
+ */
+#define KVM_REG_MIPS_MSA_IR	 (KVM_REG_MIPS_MSACR | KVM_REG_SIZE_U32 |  0)
+#define KVM_REG_MIPS_MSA_CSR	 (KVM_REG_MIPS_MSACR | KVM_REG_SIZE_U32 |  1)
+
+
+/*
+ * KVM MIPS specific structures and definitions
+ *
+ */
+struct kvm_debug_exit_arch {
+	__u64 epc;
+};
+
+/* for KVM_SET_GUEST_DEBUG */
+struct kvm_guest_debug_arch {
+};
+
+/* definition of registers in kvm_run */
+struct kvm_sync_regs {
+};
+
+/* dummy definition */
+struct kvm_sregs {
+};
+
+struct kvm_mips_interrupt {
+	/* in */
+	__u32 cpu;
+	__u32 irq;
+};
+
+#endif /* __LINUX_KVM_MIPS_H */
diff --git a/arch/mips/include/uapi/asm/mman.h b/arch/mips/include/uapi/asm/mman.h
new file mode 100644
index 000000000..c6e1fc77c
--- /dev/null
+++ b/arch/mips/include/uapi/asm/mman.h
@@ -0,0 +1,116 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995, 1999, 2002 by Ralf Baechle
+ */
+#ifndef _ASM_MMAN_H
+#define _ASM_MMAN_H
+
+/*
+ * Protections are chosen from these bits, OR'd together.  The
+ * implementation does not necessarily support PROT_EXEC or PROT_WRITE
+ * without PROT_READ.  The only guarantees are that no writing will be
+ * allowed without PROT_WRITE and no access will be allowed for PROT_NONE.
+ */
+#define PROT_NONE	0x00		/* page can not be accessed */
+#define PROT_READ	0x01		/* page can be read */
+#define PROT_WRITE	0x02		/* page can be written */
+#define PROT_EXEC	0x04		/* page can be executed */
+/*			0x08		   reserved for PROT_EXEC_NOFLUSH */
+#define PROT_SEM	0x10		/* page may be used for atomic ops */
+#define PROT_GROWSDOWN	0x01000000	/* mprotect flag: extend change to start of growsdown vma */
+#define PROT_GROWSUP	0x02000000	/* mprotect flag: extend change to end of growsup vma */
+
+/*
+ * Flags for mmap
+ */
+/* 0x01 - 0x03 are defined in linux/mman.h */
+#define MAP_TYPE	0x00f		/* Mask for type of mapping */
+#define MAP_FIXED	0x010		/* Interpret addr exactly */
+
+/* not used by linux, but here to make sure we don't clash with ABI defines */
+#define MAP_RENAME	0x020		/* Assign page to file */
+#define MAP_AUTOGROW	0x040		/* File may grow by writing */
+#define MAP_LOCAL	0x080		/* Copy on fork/sproc */
+#define MAP_AUTORSRV	0x100		/* Logical swap reserved on demand */
+
+/* These are linux-specific */
+#define MAP_NORESERVE	0x0400		/* don't check for reservations */
+#define MAP_ANONYMOUS	0x0800		/* don't use a file */
+#define MAP_GROWSDOWN	0x1000		/* stack-like segment */
+#define MAP_DENYWRITE	0x2000		/* ETXTBSY */
+#define MAP_EXECUTABLE	0x4000		/* mark it as an executable */
+#define MAP_LOCKED	0x8000		/* pages are locked */
+#define MAP_POPULATE	0x10000		/* populate (prefault) pagetables */
+#define MAP_NONBLOCK	0x20000		/* do not block on IO */
+#define MAP_STACK	0x40000		/* give out an address that is best suited for process/thread stacks */
+#define MAP_HUGETLB	0x80000		/* create a huge page mapping */
+#define MAP_FIXED_NOREPLACE 0x100000	/* MAP_FIXED which doesn't unmap underlying mapping */
+
+/*
+ * Flags for msync
+ */
+#define MS_ASYNC	0x0001		/* sync memory asynchronously */
+#define MS_INVALIDATE	0x0002		/* invalidate mappings & caches */
+#define MS_SYNC		0x0004		/* synchronous memory sync */
+
+/*
+ * Flags for mlockall
+ */
+#define MCL_CURRENT	1		/* lock all current mappings */
+#define MCL_FUTURE	2		/* lock all future mappings */
+#define MCL_ONFAULT	4		/* lock all pages that are faulted in */
+
+/*
+ * Flags for mlock
+ */
+#define MLOCK_ONFAULT	0x01		/* Lock pages in range after they are faulted in, do not prefault */
+
+#define MADV_NORMAL	0		/* no further special treatment */
+#define MADV_RANDOM	1		/* expect random page references */
+#define MADV_SEQUENTIAL 2		/* expect sequential page references */
+#define MADV_WILLNEED	3		/* will need these pages */
+#define MADV_DONTNEED	4		/* don't need these pages */
+
+/* common parameters: try to keep these consistent across architectures */
+#define MADV_FREE	8		/* free pages only if memory pressure */
+#define MADV_REMOVE	9		/* remove these pages & resources */
+#define MADV_DONTFORK	10		/* don't inherit across fork */
+#define MADV_DOFORK	11		/* do inherit across fork */
+
+#define MADV_MERGEABLE	 12		/* KSM may merge identical pages */
+#define MADV_UNMERGEABLE 13		/* KSM may not merge identical pages */
+#define MADV_HWPOISON	 100		/* poison a page for testing */
+
+#define MADV_HUGEPAGE	14		/* Worth backing with hugepages */
+#define MADV_NOHUGEPAGE 15		/* Not worth backing with hugepages */
+
+#define MADV_DONTDUMP	16		/* Explicity exclude from the core dump,
+					   overrides the coredump filter bits */
+#define MADV_DODUMP	17		/* Clear the MADV_NODUMP flag */
+
+#define MADV_WIPEONFORK 18		/* Zero memory on fork, child only */
+#define MADV_KEEPONFORK 19		/* Undo MADV_WIPEONFORK */
+
+#define MADV_COLD	20		/* deactivate these pages */
+#define MADV_PAGEOUT	21		/* reclaim these pages */
+
+#define MADV_POPULATE_READ	22	/* populate (prefault) page tables readable */
+#define MADV_POPULATE_WRITE	23	/* populate (prefault) page tables writable */
+
+#define MADV_DONTNEED_LOCKED	24	/* like DONTNEED, but drop locked pages too */
+
+#define MADV_COLLAPSE	25		/* Synchronous hugepage collapse */
+
+/* compatibility flags */
+#define MAP_FILE	0
+
+#define PKEY_DISABLE_ACCESS	0x1
+#define PKEY_DISABLE_WRITE	0x2
+#define PKEY_ACCESS_MASK	(PKEY_DISABLE_ACCESS |\
+				 PKEY_DISABLE_WRITE)
+
+#endif /* _ASM_MMAN_H */
diff --git a/arch/mips/include/uapi/asm/msgbuf.h b/arch/mips/include/uapi/asm/msgbuf.h
new file mode 100644
index 000000000..128af72f2
--- /dev/null
+++ b/arch/mips/include/uapi/asm/msgbuf.h
@@ -0,0 +1,68 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+#ifndef _ASM_MSGBUF_H
+#define _ASM_MSGBUF_H
+
+#include <asm/ipcbuf.h>
+
+/*
+ * The msqid64_ds structure for the MIPS architecture.
+ * Note extra padding because this structure is passed back and forth
+ * between kernel and user space.
+ *
+ * Pad space is left for:
+ * - 2 miscellaneous unsigned long values
+ */
+
+#if defined(__mips64)
+struct msqid64_ds {
+	struct ipc64_perm msg_perm;
+	long msg_stime;			/* last msgsnd time */
+	long msg_rtime;			/* last msgrcv time */
+	long msg_ctime;			/* last change time */
+	unsigned long  msg_cbytes;	/* current number of bytes on queue */
+	unsigned long  msg_qnum;	/* number of messages in queue */
+	unsigned long  msg_qbytes;	/* max number of bytes on queue */
+	__kernel_pid_t msg_lspid;	/* pid of last msgsnd */
+	__kernel_pid_t msg_lrpid;	/* last receive pid */
+	unsigned long  __unused4;
+	unsigned long  __unused5;
+};
+#elif defined (__MIPSEB__)
+struct msqid64_ds {
+	struct ipc64_perm msg_perm;
+	unsigned long  msg_stime_high;
+	unsigned long  msg_stime;	/* last msgsnd time */
+	unsigned long  msg_rtime_high;
+	unsigned long  msg_rtime;	/* last msgrcv time */
+	unsigned long  msg_ctime_high;
+	unsigned long  msg_ctime;	/* last change time */
+	unsigned long  msg_cbytes;	/* current number of bytes on queue */
+	unsigned long  msg_qnum;	/* number of messages in queue */
+	unsigned long  msg_qbytes;	/* max number of bytes on queue */
+	__kernel_pid_t msg_lspid;	/* pid of last msgsnd */
+	__kernel_pid_t msg_lrpid;	/* last receive pid */
+	unsigned long  __unused4;
+	unsigned long  __unused5;
+};
+#elif defined (__MIPSEL__)
+struct msqid64_ds {
+	struct ipc64_perm msg_perm;
+	unsigned long  msg_stime;	/* last msgsnd time */
+	unsigned long  msg_stime_high;
+	unsigned long  msg_rtime;	/* last msgrcv time */
+	unsigned long  msg_rtime_high;
+	unsigned long  msg_ctime;	/* last change time */
+	unsigned long  msg_ctime_high;
+	unsigned long  msg_cbytes;	/* current number of bytes on queue */
+	unsigned long  msg_qnum;	/* number of messages in queue */
+	unsigned long  msg_qbytes;	/* max number of bytes on queue */
+	__kernel_pid_t msg_lspid;	/* pid of last msgsnd */
+	__kernel_pid_t msg_lrpid;	/* last receive pid */
+	unsigned long  __unused4;
+	unsigned long  __unused5;
+};
+#else
+#warning no endianess set
+#endif
+
+#endif /* _ASM_MSGBUF_H */
diff --git a/arch/mips/include/uapi/asm/param.h b/arch/mips/include/uapi/asm/param.h
new file mode 100644
index 000000000..3f337ed66
--- /dev/null
+++ b/arch/mips/include/uapi/asm/param.h
@@ -0,0 +1,17 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright 1994 - 2000, 2002 Ralf Baechle (ralf@gnu.org)
+ * Copyright 2000 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_PARAM_H
+#define _ASM_PARAM_H
+
+#define EXEC_PAGESIZE	65536
+
+#include <asm-generic/param.h>
+
+#endif /* _ASM_PARAM_H */
diff --git a/arch/mips/include/uapi/asm/perf_regs.h b/arch/mips/include/uapi/asm/perf_regs.h
new file mode 100644
index 000000000..d0f4ecd61
--- /dev/null
+++ b/arch/mips/include/uapi/asm/perf_regs.h
@@ -0,0 +1,40 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+#ifndef _ASM_MIPS_PERF_REGS_H
+#define _ASM_MIPS_PERF_REGS_H
+
+enum perf_event_mips_regs {
+	PERF_REG_MIPS_PC,
+	PERF_REG_MIPS_R1,
+	PERF_REG_MIPS_R2,
+	PERF_REG_MIPS_R3,
+	PERF_REG_MIPS_R4,
+	PERF_REG_MIPS_R5,
+	PERF_REG_MIPS_R6,
+	PERF_REG_MIPS_R7,
+	PERF_REG_MIPS_R8,
+	PERF_REG_MIPS_R9,
+	PERF_REG_MIPS_R10,
+	PERF_REG_MIPS_R11,
+	PERF_REG_MIPS_R12,
+	PERF_REG_MIPS_R13,
+	PERF_REG_MIPS_R14,
+	PERF_REG_MIPS_R15,
+	PERF_REG_MIPS_R16,
+	PERF_REG_MIPS_R17,
+	PERF_REG_MIPS_R18,
+	PERF_REG_MIPS_R19,
+	PERF_REG_MIPS_R20,
+	PERF_REG_MIPS_R21,
+	PERF_REG_MIPS_R22,
+	PERF_REG_MIPS_R23,
+	PERF_REG_MIPS_R24,
+	PERF_REG_MIPS_R25,
+	PERF_REG_MIPS_R26,
+	PERF_REG_MIPS_R27,
+	PERF_REG_MIPS_R28,
+	PERF_REG_MIPS_R29,
+	PERF_REG_MIPS_R30,
+	PERF_REG_MIPS_R31,
+	PERF_REG_MIPS_MAX = PERF_REG_MIPS_R31 + 1,
+};
+#endif /* _ASM_MIPS_PERF_REGS_H */
diff --git a/arch/mips/include/uapi/asm/poll.h b/arch/mips/include/uapi/asm/poll.h
new file mode 100644
index 000000000..ad289d7b7
--- /dev/null
+++ b/arch/mips/include/uapi/asm/poll.h
@@ -0,0 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+#ifndef __ASM_POLL_H
+#define __ASM_POLL_H
+
+#define POLLWRNORM	POLLOUT
+#define POLLWRBAND	0x0100
+
+#include <asm-generic/poll.h>
+
+#endif /* __ASM_POLL_H */
diff --git a/arch/mips/include/uapi/asm/posix_types.h b/arch/mips/include/uapi/asm/posix_types.h
new file mode 100644
index 000000000..f0ccb5b90
--- /dev/null
+++ b/arch/mips/include/uapi/asm/posix_types.h
@@ -0,0 +1,26 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1996, 97, 98, 99, 2000 by Ralf Baechle
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_POSIX_TYPES_H
+#define _ASM_POSIX_TYPES_H
+
+#include <asm/sgidefs.h>
+
+/*
+ * This file is generally used by user-level software, so you need to
+ * be a little careful about namespace pollution etc.  Also, we cannot
+ * assume GCC is being used.
+ */
+
+typedef long		__kernel_daddr_t;
+#define __kernel_daddr_t __kernel_daddr_t
+
+#include <asm-generic/posix_types.h>
+
+#endif /* _ASM_POSIX_TYPES_H */
diff --git a/arch/mips/include/uapi/asm/ptrace.h b/arch/mips/include/uapi/asm/ptrace.h
new file mode 100644
index 000000000..f3c025445
--- /dev/null
+++ b/arch/mips/include/uapi/asm/ptrace.h
@@ -0,0 +1,109 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994, 95, 96, 97, 98, 99, 2000 by Ralf Baechle
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ */
+#ifndef _UAPI_ASM_PTRACE_H
+#define _UAPI_ASM_PTRACE_H
+
+#include <linux/types.h>
+
+/* 0 - 31 are integer registers, 32 - 63 are fp registers.  */
+#define FPR_BASE	32
+#define PC		64
+#define CAUSE		65
+#define BADVADDR	66
+#define MMHI		67
+#define MMLO		68
+#define FPC_CSR		69
+#define FPC_EIR		70
+#define DSP_BASE	71		/* 3 more hi / lo register pairs */
+#define DSP_CONTROL	77
+#define ACX		78
+
+/*
+ * This struct defines the registers as used by PTRACE_{GET,SET}REGS. The
+ * format is the same for both 32- and 64-bit processes. Registers for 32-bit
+ * processes are sign extended.
+ */
+#ifdef __KERNEL__
+struct user_pt_regs {
+#else
+struct pt_regs {
+#endif
+	/* Saved main processor registers. */
+	__u64 regs[32];
+
+	/* Saved special registers. */
+	__u64 lo;
+	__u64 hi;
+	__u64 cp0_epc;
+	__u64 cp0_badvaddr;
+	__u64 cp0_status;
+	__u64 cp0_cause;
+} __attribute__ ((aligned (8)));
+
+/* Arbitrarily choose the same ptrace numbers as used by the Sparc code. */
+#define PTRACE_GETREGS		12
+#define PTRACE_SETREGS		13
+#define PTRACE_GETFPREGS		14
+#define PTRACE_SETFPREGS		15
+/* #define PTRACE_GETFPXREGS		18 */
+/* #define PTRACE_SETFPXREGS		19 */
+
+#define PTRACE_OLDSETOPTIONS	21
+
+#define PTRACE_GET_THREAD_AREA	25
+#define PTRACE_SET_THREAD_AREA	26
+
+/* Calls to trace a 64bit program from a 32bit program.	 */
+#define PTRACE_PEEKTEXT_3264	0xc0
+#define PTRACE_PEEKDATA_3264	0xc1
+#define PTRACE_POKETEXT_3264	0xc2
+#define PTRACE_POKEDATA_3264	0xc3
+#define PTRACE_GET_THREAD_AREA_3264	0xc4
+
+/* Read and write watchpoint registers.	 */
+enum pt_watch_style {
+	pt_watch_style_mips32,
+	pt_watch_style_mips64
+};
+struct mips32_watch_regs {
+	unsigned int watchlo[8];
+	/* Lower 16 bits of watchhi. */
+	unsigned short watchhi[8];
+	/* Valid mask and I R W bits.
+	 * bit 0 -- 1 if W bit is usable.
+	 * bit 1 -- 1 if R bit is usable.
+	 * bit 2 -- 1 if I bit is usable.
+	 * bits 3 - 11 -- Valid watchhi mask bits.
+	 */
+	unsigned short watch_masks[8];
+	/* The number of valid watch register pairs.  */
+	unsigned int num_valid;
+} __attribute__((aligned(8)));
+
+struct mips64_watch_regs {
+	unsigned long long watchlo[8];
+	unsigned short watchhi[8];
+	unsigned short watch_masks[8];
+	unsigned int num_valid;
+} __attribute__((aligned(8)));
+
+struct pt_watch_regs {
+	enum pt_watch_style style;
+	union {
+		struct mips32_watch_regs mips32;
+		struct mips64_watch_regs mips64;
+	};
+};
+
+#define PTRACE_GET_WATCH_REGS	0xd0
+#define PTRACE_SET_WATCH_REGS	0xd1
+
+
+#endif /* _UAPI_ASM_PTRACE_H */
diff --git a/arch/mips/include/uapi/asm/reg.h b/arch/mips/include/uapi/asm/reg.h
new file mode 100644
index 000000000..56d15cb81
--- /dev/null
+++ b/arch/mips/include/uapi/asm/reg.h
@@ -0,0 +1,207 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * Various register offset definitions for debuggers, core file
+ * examiners and whatnot.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995, 1999 Ralf Baechle
+ * Copyright (C) 1995, 1999 Silicon Graphics
+ */
+#ifndef __UAPI_ASM_MIPS_REG_H
+#define __UAPI_ASM_MIPS_REG_H
+
+#define MIPS32_EF_R0		6
+#define MIPS32_EF_R1		7
+#define MIPS32_EF_R2		8
+#define MIPS32_EF_R3		9
+#define MIPS32_EF_R4		10
+#define MIPS32_EF_R5		11
+#define MIPS32_EF_R6		12
+#define MIPS32_EF_R7		13
+#define MIPS32_EF_R8		14
+#define MIPS32_EF_R9		15
+#define MIPS32_EF_R10		16
+#define MIPS32_EF_R11		17
+#define MIPS32_EF_R12		18
+#define MIPS32_EF_R13		19
+#define MIPS32_EF_R14		20
+#define MIPS32_EF_R15		21
+#define MIPS32_EF_R16		22
+#define MIPS32_EF_R17		23
+#define MIPS32_EF_R18		24
+#define MIPS32_EF_R19		25
+#define MIPS32_EF_R20		26
+#define MIPS32_EF_R21		27
+#define MIPS32_EF_R22		28
+#define MIPS32_EF_R23		29
+#define MIPS32_EF_R24		30
+#define MIPS32_EF_R25		31
+
+/*
+ * k0/k1 unsaved
+ */
+#define MIPS32_EF_R26		32
+#define MIPS32_EF_R27		33
+
+#define MIPS32_EF_R28		34
+#define MIPS32_EF_R29		35
+#define MIPS32_EF_R30		36
+#define MIPS32_EF_R31		37
+
+/*
+ * Saved special registers
+ */
+#define MIPS32_EF_LO		38
+#define MIPS32_EF_HI		39
+
+#define MIPS32_EF_CP0_EPC	40
+#define MIPS32_EF_CP0_BADVADDR	41
+#define MIPS32_EF_CP0_STATUS	42
+#define MIPS32_EF_CP0_CAUSE	43
+#define MIPS32_EF_UNUSED0	44
+
+#define MIPS32_EF_SIZE		180
+
+#define MIPS64_EF_R0		0
+#define MIPS64_EF_R1		1
+#define MIPS64_EF_R2		2
+#define MIPS64_EF_R3		3
+#define MIPS64_EF_R4		4
+#define MIPS64_EF_R5		5
+#define MIPS64_EF_R6		6
+#define MIPS64_EF_R7		7
+#define MIPS64_EF_R8		8
+#define MIPS64_EF_R9		9
+#define MIPS64_EF_R10		10
+#define MIPS64_EF_R11		11
+#define MIPS64_EF_R12		12
+#define MIPS64_EF_R13		13
+#define MIPS64_EF_R14		14
+#define MIPS64_EF_R15		15
+#define MIPS64_EF_R16		16
+#define MIPS64_EF_R17		17
+#define MIPS64_EF_R18		18
+#define MIPS64_EF_R19		19
+#define MIPS64_EF_R20		20
+#define MIPS64_EF_R21		21
+#define MIPS64_EF_R22		22
+#define MIPS64_EF_R23		23
+#define MIPS64_EF_R24		24
+#define MIPS64_EF_R25		25
+
+/*
+ * k0/k1 unsaved
+ */
+#define MIPS64_EF_R26		26
+#define MIPS64_EF_R27		27
+
+
+#define MIPS64_EF_R28		28
+#define MIPS64_EF_R29		29
+#define MIPS64_EF_R30		30
+#define MIPS64_EF_R31		31
+
+/*
+ * Saved special registers
+ */
+#define MIPS64_EF_LO		32
+#define MIPS64_EF_HI		33
+
+#define MIPS64_EF_CP0_EPC	34
+#define MIPS64_EF_CP0_BADVADDR	35
+#define MIPS64_EF_CP0_STATUS	36
+#define MIPS64_EF_CP0_CAUSE	37
+
+#define MIPS64_EF_SIZE		304	/* size in bytes */
+
+#if _MIPS_SIM == _MIPS_SIM_ABI32
+
+#define EF_R0			MIPS32_EF_R0
+#define EF_R1			MIPS32_EF_R1
+#define EF_R2			MIPS32_EF_R2
+#define EF_R3			MIPS32_EF_R3
+#define EF_R4			MIPS32_EF_R4
+#define EF_R5			MIPS32_EF_R5
+#define EF_R6			MIPS32_EF_R6
+#define EF_R7			MIPS32_EF_R7
+#define EF_R8			MIPS32_EF_R8
+#define EF_R9			MIPS32_EF_R9
+#define EF_R10			MIPS32_EF_R10
+#define EF_R11			MIPS32_EF_R11
+#define EF_R12			MIPS32_EF_R12
+#define EF_R13			MIPS32_EF_R13
+#define EF_R14			MIPS32_EF_R14
+#define EF_R15			MIPS32_EF_R15
+#define EF_R16			MIPS32_EF_R16
+#define EF_R17			MIPS32_EF_R17
+#define EF_R18			MIPS32_EF_R18
+#define EF_R19			MIPS32_EF_R19
+#define EF_R20			MIPS32_EF_R20
+#define EF_R21			MIPS32_EF_R21
+#define EF_R22			MIPS32_EF_R22
+#define EF_R23			MIPS32_EF_R23
+#define EF_R24			MIPS32_EF_R24
+#define EF_R25			MIPS32_EF_R25
+#define EF_R26			MIPS32_EF_R26
+#define EF_R27			MIPS32_EF_R27
+#define EF_R28			MIPS32_EF_R28
+#define EF_R29			MIPS32_EF_R29
+#define EF_R30			MIPS32_EF_R30
+#define EF_R31			MIPS32_EF_R31
+#define EF_LO			MIPS32_EF_LO
+#define EF_HI			MIPS32_EF_HI
+#define EF_CP0_EPC		MIPS32_EF_CP0_EPC
+#define EF_CP0_BADVADDR		MIPS32_EF_CP0_BADVADDR
+#define EF_CP0_STATUS		MIPS32_EF_CP0_STATUS
+#define EF_CP0_CAUSE		MIPS32_EF_CP0_CAUSE
+#define EF_UNUSED0		MIPS32_EF_UNUSED0
+#define EF_SIZE			MIPS32_EF_SIZE
+
+#elif _MIPS_SIM == _MIPS_SIM_ABI64 || _MIPS_SIM == _MIPS_SIM_NABI32
+
+#define EF_R0			MIPS64_EF_R0
+#define EF_R1			MIPS64_EF_R1
+#define EF_R2			MIPS64_EF_R2
+#define EF_R3			MIPS64_EF_R3
+#define EF_R4			MIPS64_EF_R4
+#define EF_R5			MIPS64_EF_R5
+#define EF_R6			MIPS64_EF_R6
+#define EF_R7			MIPS64_EF_R7
+#define EF_R8			MIPS64_EF_R8
+#define EF_R9			MIPS64_EF_R9
+#define EF_R10			MIPS64_EF_R10
+#define EF_R11			MIPS64_EF_R11
+#define EF_R12			MIPS64_EF_R12
+#define EF_R13			MIPS64_EF_R13
+#define EF_R14			MIPS64_EF_R14
+#define EF_R15			MIPS64_EF_R15
+#define EF_R16			MIPS64_EF_R16
+#define EF_R17			MIPS64_EF_R17
+#define EF_R18			MIPS64_EF_R18
+#define EF_R19			MIPS64_EF_R19
+#define EF_R20			MIPS64_EF_R20
+#define EF_R21			MIPS64_EF_R21
+#define EF_R22			MIPS64_EF_R22
+#define EF_R23			MIPS64_EF_R23
+#define EF_R24			MIPS64_EF_R24
+#define EF_R25			MIPS64_EF_R25
+#define EF_R26			MIPS64_EF_R26
+#define EF_R27			MIPS64_EF_R27
+#define EF_R28			MIPS64_EF_R28
+#define EF_R29			MIPS64_EF_R29
+#define EF_R30			MIPS64_EF_R30
+#define EF_R31			MIPS64_EF_R31
+#define EF_LO			MIPS64_EF_LO
+#define EF_HI			MIPS64_EF_HI
+#define EF_CP0_EPC		MIPS64_EF_CP0_EPC
+#define EF_CP0_BADVADDR		MIPS64_EF_CP0_BADVADDR
+#define EF_CP0_STATUS		MIPS64_EF_CP0_STATUS
+#define EF_CP0_CAUSE		MIPS64_EF_CP0_CAUSE
+#define EF_SIZE			MIPS64_EF_SIZE
+
+#endif /* _MIPS_SIM == _MIPS_SIM_ABI64 || _MIPS_SIM == _MIPS_SIM_NABI32 */
+
+#endif /* __UAPI_ASM_MIPS_REG_H */
diff --git a/arch/mips/include/uapi/asm/resource.h b/arch/mips/include/uapi/asm/resource.h
new file mode 100644
index 000000000..372ff8f4b
--- /dev/null
+++ b/arch/mips/include/uapi/asm/resource.h
@@ -0,0 +1,36 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995, 96, 98, 99, 2000 by Ralf Baechle
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_RESOURCE_H
+#define _ASM_RESOURCE_H
+
+
+/*
+ * These five resource limit IDs have a MIPS/Linux-specific ordering,
+ * the rest comes from the generic header:
+ */
+#define RLIMIT_NOFILE		5	/* max number of open files */
+#define RLIMIT_AS		6	/* address space limit */
+#define RLIMIT_RSS		7	/* max resident set size */
+#define RLIMIT_NPROC		8	/* max number of processes */
+#define RLIMIT_MEMLOCK		9	/* max locked-in-memory address space */
+
+/*
+ * SuS says limits have to be unsigned.
+ * Which makes a ton more sense anyway,
+ * but we keep the old value on MIPS32,
+ * for compatibility:
+ */
+#ifndef __mips64
+# define RLIM_INFINITY		0x7fffffffUL
+#endif
+
+#include <asm-generic/resource.h>
+
+#endif /* _ASM_RESOURCE_H */
diff --git a/arch/mips/include/uapi/asm/sembuf.h b/arch/mips/include/uapi/asm/sembuf.h
new file mode 100644
index 000000000..ba7fe0c89
--- /dev/null
+++ b/arch/mips/include/uapi/asm/sembuf.h
@@ -0,0 +1,36 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+#ifndef _ASM_SEMBUF_H
+#define _ASM_SEMBUF_H
+
+#include <asm/ipcbuf.h>
+
+/*
+ * The semid64_ds structure for the MIPS architecture.
+ * Note extra padding because this structure is passed back and forth
+ * between kernel and user space.
+ *
+ * Pad space is left for 2 miscellaneous 64-bit values on mips64,
+ * but used for the upper 32 bit of the time values on mips32.
+ */
+
+#ifdef __mips64
+struct semid64_ds {
+	struct ipc64_perm sem_perm;		/* permissions .. see ipc.h */
+	long		 sem_otime;		/* last semop time */
+	long		 sem_ctime;		/* last change time */
+	unsigned long	sem_nsems;		/* no. of semaphores in array */
+	unsigned long	__unused1;
+	unsigned long	__unused2;
+};
+#else
+struct semid64_ds {
+	struct ipc64_perm sem_perm;		/* permissions .. see ipc.h */
+	unsigned long   sem_otime;		/* last semop time */
+	unsigned long   sem_ctime;		/* last change time */
+	unsigned long	sem_nsems;		/* no. of semaphores in array */
+	unsigned long	sem_otime_high;
+	unsigned long	sem_ctime_high;
+};
+#endif
+
+#endif /* _ASM_SEMBUF_H */
diff --git a/arch/mips/include/uapi/asm/setup.h b/arch/mips/include/uapi/asm/setup.h
new file mode 100644
index 000000000..7d48c433b
--- /dev/null
+++ b/arch/mips/include/uapi/asm/setup.h
@@ -0,0 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+#ifndef _UAPI_MIPS_SETUP_H
+#define _UAPI_MIPS_SETUP_H
+
+#define COMMAND_LINE_SIZE	4096
+
+
+#endif /* _UAPI_MIPS_SETUP_H */
diff --git a/arch/mips/include/uapi/asm/sgidefs.h b/arch/mips/include/uapi/asm/sgidefs.h
new file mode 100644
index 000000000..69c3de90c
--- /dev/null
+++ b/arch/mips/include/uapi/asm/sgidefs.h
@@ -0,0 +1,37 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1996, 1999, 2001 Ralf Baechle
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ * Copyright (C) 2001 MIPS Technologies, Inc.
+ */
+#ifndef __ASM_SGIDEFS_H
+#define __ASM_SGIDEFS_H
+
+/*
+ * Definitions for the ISA levels
+ *
+ * With the introduction of MIPS32 / MIPS64 instruction sets definitions
+ * MIPS ISAs are no longer subsets of each other.  Therefore comparisons
+ * on these symbols except with == may result in unexpected results and
+ * are forbidden!
+ */
+#define _MIPS_ISA_MIPS1		1
+#define _MIPS_ISA_MIPS2		2
+#define _MIPS_ISA_MIPS3		3
+#define _MIPS_ISA_MIPS4		4
+#define _MIPS_ISA_MIPS5		5
+#define _MIPS_ISA_MIPS32	6
+#define _MIPS_ISA_MIPS64	7
+
+/*
+ * Subprogram calling convention
+ */
+#define _MIPS_SIM_ABI32		1
+#define _MIPS_SIM_NABI32	2
+#define _MIPS_SIM_ABI64		3
+
+#endif /* __ASM_SGIDEFS_H */
diff --git a/arch/mips/include/uapi/asm/shmbuf.h b/arch/mips/include/uapi/asm/shmbuf.h
new file mode 100644
index 000000000..eb74d304b
--- /dev/null
+++ b/arch/mips/include/uapi/asm/shmbuf.h
@@ -0,0 +1,61 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+#ifndef _ASM_SHMBUF_H
+#define _ASM_SHMBUF_H
+
+#include <asm/ipcbuf.h>
+#include <asm/posix_types.h>
+
+/*
+ * The shmid64_ds structure for the MIPS architecture.
+ * Note extra padding because this structure is passed back and forth
+ * between kernel and user space.
+ *
+ * As MIPS was lacking proper padding after shm_?time, we use 48 bits
+ * of the padding at the end to store a few additional bits of the time.
+ * libc implementations need to take care to convert this into a proper
+ * data structure when moving to 64-bit time_t.
+ */
+
+#ifdef __mips64
+struct shmid64_ds {
+	struct ipc64_perm	shm_perm;	/* operation perms */
+	__kernel_size_t		shm_segsz;	/* size of segment (bytes) */
+	long			shm_atime;	/* last attach time */
+	long			shm_dtime;	/* last detach time */
+	long			shm_ctime;	/* last change time */
+	__kernel_pid_t		shm_cpid;	/* pid of creator */
+	__kernel_pid_t		shm_lpid;	/* pid of last operator */
+	unsigned long		shm_nattch;	/* no. of current attaches */
+	unsigned long		__unused1;
+	unsigned long		__unused2;
+};
+#else
+struct shmid64_ds {
+	struct ipc64_perm	shm_perm;	/* operation perms */
+	__kernel_size_t		shm_segsz;	/* size of segment (bytes) */
+	unsigned long		shm_atime;	/* last attach time */
+	unsigned long		shm_dtime;	/* last detach time */
+	unsigned long		shm_ctime;	/* last change time */
+	__kernel_pid_t		shm_cpid;	/* pid of creator */
+	__kernel_pid_t		shm_lpid;	/* pid of last operator */
+	unsigned long		shm_nattch;	/* no. of current attaches */
+	unsigned short		shm_atime_high;
+	unsigned short		shm_dtime_high;
+	unsigned short		shm_ctime_high;
+	unsigned short		__unused1;
+};
+#endif
+
+struct shminfo64 {
+	unsigned long	shmmax;
+	unsigned long	shmmin;
+	unsigned long	shmmni;
+	unsigned long	shmseg;
+	unsigned long	shmall;
+	unsigned long	__unused1;
+	unsigned long	__unused2;
+	unsigned long	__unused3;
+	unsigned long	__unused4;
+};
+
+#endif /* _ASM_SHMBUF_H */
diff --git a/arch/mips/include/uapi/asm/sigcontext.h b/arch/mips/include/uapi/asm/sigcontext.h
new file mode 100644
index 000000000..d0a540e88
--- /dev/null
+++ b/arch/mips/include/uapi/asm/sigcontext.h
@@ -0,0 +1,91 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1996, 1997, 1999 by Ralf Baechle
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ */
+#ifndef _UAPI_ASM_SIGCONTEXT_H
+#define _UAPI_ASM_SIGCONTEXT_H
+
+#include <linux/types.h>
+#include <asm/sgidefs.h>
+
+/* scalar FP context was used */
+#define USED_FP			(1 << 0)
+
+/* the value of Status.FR when context was saved */
+#define USED_FR1		(1 << 1)
+
+/* FR=1, but with odd singles in bits 63:32 of preceding even double */
+#define USED_HYBRID_FPRS	(1 << 2)
+
+/* extended context was used, see struct extcontext for details */
+#define USED_EXTCONTEXT		(1 << 3)
+
+#if _MIPS_SIM == _MIPS_SIM_ABI32
+
+/*
+ * Keep this struct definition in sync with the sigcontext fragment
+ * in arch/mips/kernel/asm-offsets.c
+ */
+struct sigcontext {
+	unsigned int		sc_regmask;	/* Unused */
+	unsigned int		sc_status;	/* Unused */
+	unsigned long long	sc_pc;
+	unsigned long long	sc_regs[32];
+	unsigned long long	sc_fpregs[32];
+	unsigned int		sc_acx;		/* Was sc_ownedfp */
+	unsigned int		sc_fpc_csr;
+	unsigned int		sc_fpc_eir;	/* Unused */
+	unsigned int		sc_used_math;
+	unsigned int		sc_dsp;		/* dsp status, was sc_ssflags */
+	unsigned long long	sc_mdhi;
+	unsigned long long	sc_mdlo;
+	unsigned long		sc_hi1;		/* Was sc_cause */
+	unsigned long		sc_lo1;		/* Was sc_badvaddr */
+	unsigned long		sc_hi2;		/* Was sc_sigset[4] */
+	unsigned long		sc_lo2;
+	unsigned long		sc_hi3;
+	unsigned long		sc_lo3;
+};
+
+#endif /* _MIPS_SIM == _MIPS_SIM_ABI32 */
+
+#if _MIPS_SIM == _MIPS_SIM_ABI64 || _MIPS_SIM == _MIPS_SIM_NABI32
+
+#include <linux/posix_types.h>
+/*
+ * Keep this struct definition in sync with the sigcontext fragment
+ * in arch/mips/kernel/asm-offsets.c
+ *
+ * Warning: this structure illdefined with sc_badvaddr being just an unsigned
+ * int so it was changed to unsigned long in 2.6.0-test1.  This may break
+ * binary compatibility - no prisoners.
+ * DSP ASE in 2.6.12-rc4.  Turn sc_mdhi and sc_mdlo into an array of four
+ * entries, add sc_dsp and sc_reserved for padding.  No prisoners.
+ */
+struct sigcontext {
+	__u64	sc_regs[32];
+	__u64	sc_fpregs[32];
+	__u64	sc_mdhi;
+	__u64	sc_hi1;
+	__u64	sc_hi2;
+	__u64	sc_hi3;
+	__u64	sc_mdlo;
+	__u64	sc_lo1;
+	__u64	sc_lo2;
+	__u64	sc_lo3;
+	__u64	sc_pc;
+	__u32	sc_fpc_csr;
+	__u32	sc_used_math;
+	__u32	sc_dsp;
+	__u32	sc_reserved;
+};
+
+
+#endif /* _MIPS_SIM == _MIPS_SIM_ABI64 || _MIPS_SIM == _MIPS_SIM_NABI32 */
+
+#endif /* _UAPI_ASM_SIGCONTEXT_H */
diff --git a/arch/mips/include/uapi/asm/siginfo.h b/arch/mips/include/uapi/asm/siginfo.h
new file mode 100644
index 000000000..8cb8bd061
--- /dev/null
+++ b/arch/mips/include/uapi/asm/siginfo.h
@@ -0,0 +1,30 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1998, 1999, 2001, 2003 Ralf Baechle
+ * Copyright (C) 2000, 2001 Silicon Graphics, Inc.
+ */
+#ifndef _UAPI_ASM_SIGINFO_H
+#define _UAPI_ASM_SIGINFO_H
+
+#define __ARCH_SIGEV_PREAMBLE_SIZE (sizeof(long) + 2*sizeof(int))
+
+#define __ARCH_HAS_SWAPPED_SIGINFO
+
+#include <asm-generic/siginfo.h>
+
+/*
+ * si_code values
+ * Again these have been chosen to be IRIX compatible.
+ */
+#undef SI_ASYNCIO
+#undef SI_TIMER
+#undef SI_MESGQ
+#define SI_ASYNCIO	-2	/* sent by AIO completion */
+#define SI_TIMER	-3	/* sent by timer expiration */
+#define SI_MESGQ	-4	/* sent by real time mesq state change */
+
+#endif /* _UAPI_ASM_SIGINFO_H */
diff --git a/arch/mips/include/uapi/asm/signal.h b/arch/mips/include/uapi/asm/signal.h
new file mode 100644
index 000000000..94a00f82e
--- /dev/null
+++ b/arch/mips/include/uapi/asm/signal.h
@@ -0,0 +1,108 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995, 96, 97, 98, 99, 2003 by Ralf Baechle
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ */
+#ifndef _UAPI_ASM_SIGNAL_H
+#define _UAPI_ASM_SIGNAL_H
+
+#include <linux/types.h>
+
+#define _NSIG		128
+#define _NSIG_BPW	(sizeof(unsigned long) * 8)
+#define _NSIG_WORDS	(_NSIG / _NSIG_BPW)
+
+typedef struct {
+	unsigned long sig[_NSIG_WORDS];
+} sigset_t;
+
+typedef unsigned long old_sigset_t;		/* at least 32 bits */
+
+#define SIGHUP		 1	/* Hangup (POSIX).  */
+#define SIGINT		 2	/* Interrupt (ANSI).  */
+#define SIGQUIT		 3	/* Quit (POSIX).  */
+#define SIGILL		 4	/* Illegal instruction (ANSI).	*/
+#define SIGTRAP		 5	/* Trace trap (POSIX).	*/
+#define SIGIOT		 6	/* IOT trap (4.2 BSD).	*/
+#define SIGABRT		 SIGIOT /* Abort (ANSI).  */
+#define SIGEMT		 7
+#define SIGFPE		 8	/* Floating-point exception (ANSI).  */
+#define SIGKILL		 9	/* Kill, unblockable (POSIX).  */
+#define SIGBUS		10	/* BUS error (4.2 BSD).	 */
+#define SIGSEGV		11	/* Segmentation violation (ANSI).  */
+#define SIGSYS		12
+#define SIGPIPE		13	/* Broken pipe (POSIX).	 */
+#define SIGALRM		14	/* Alarm clock (POSIX).	 */
+#define SIGTERM		15	/* Termination (ANSI).	*/
+#define SIGUSR1		16	/* User-defined signal 1 (POSIX).  */
+#define SIGUSR2		17	/* User-defined signal 2 (POSIX).  */
+#define SIGCHLD		18	/* Child status has changed (POSIX).  */
+#define SIGCLD		SIGCHLD /* Same as SIGCHLD (System V).	*/
+#define SIGPWR		19	/* Power failure restart (System V).  */
+#define SIGWINCH	20	/* Window size change (4.3 BSD, Sun).  */
+#define SIGURG		21	/* Urgent condition on socket (4.2 BSD).  */
+#define SIGIO		22	/* I/O now possible (4.2 BSD).	*/
+#define SIGPOLL		SIGIO	/* Pollable event occurred (System V).	*/
+#define SIGSTOP		23	/* Stop, unblockable (POSIX).  */
+#define SIGTSTP		24	/* Keyboard stop (POSIX).  */
+#define SIGCONT		25	/* Continue (POSIX).  */
+#define SIGTTIN		26	/* Background read from tty (POSIX).  */
+#define SIGTTOU		27	/* Background write to tty (POSIX).  */
+#define SIGVTALRM	28	/* Virtual alarm clock (4.2 BSD).  */
+#define SIGPROF		29	/* Profiling alarm clock (4.2 BSD).  */
+#define SIGXCPU		30	/* CPU limit exceeded (4.2 BSD).  */
+#define SIGXFSZ		31	/* File size limit exceeded (4.2 BSD).	*/
+
+/* These should not be considered constants from userland.  */
+#define SIGRTMIN	32
+#define SIGRTMAX	_NSIG
+
+/*
+ * SA_RESTORER used to be defined as 0x04000000 but only the O32 ABI ever
+ * supported its use and no libc was using it, so the entire sa-restorer
+ * functionality was removed with lmo commit 39bffc12c3580ab for 2.5.48
+ * retaining only the SA_RESTORER definition as a reminder to avoid
+ * accidental reuse of the mask bit.
+ */
+#define SA_ONSTACK	0x08000000
+#define SA_RESETHAND	0x80000000
+#define SA_RESTART	0x10000000
+#define SA_SIGINFO	0x00000008
+#define SA_NODEFER	0x40000000
+#define SA_NOCLDWAIT	0x00010000
+#define SA_NOCLDSTOP	0x00000001
+
+#define SA_NOMASK	SA_NODEFER
+#define SA_ONESHOT	SA_RESETHAND
+
+#define MINSIGSTKSZ    2048
+#define SIGSTKSZ       8192
+
+
+#define SIG_BLOCK	1	/* for blocking signals */
+#define SIG_UNBLOCK	2	/* for unblocking signals */
+#define SIG_SETMASK	3	/* for setting the signal mask */
+
+#include <asm-generic/signal-defs.h>
+
+#ifndef __KERNEL__
+struct sigaction {
+	unsigned int	sa_flags;
+	__sighandler_t	sa_handler;
+	sigset_t	sa_mask;
+};
+#endif
+
+/* IRIX compatible stack_t  */
+typedef struct sigaltstack {
+	void __user *ss_sp;
+	__kernel_size_t ss_size;
+	int ss_flags;
+} stack_t;
+
+
+#endif /* _UAPI_ASM_SIGNAL_H */
diff --git a/arch/mips/include/uapi/asm/socket.h b/arch/mips/include/uapi/asm/socket.h
new file mode 100644
index 000000000..18f3d95ec
--- /dev/null
+++ b/arch/mips/include/uapi/asm/socket.h
@@ -0,0 +1,175 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1997, 1999, 2000, 2001 Ralf Baechle
+ * Copyright (C) 2000, 2001 Silicon Graphics, Inc.
+ */
+#ifndef _UAPI_ASM_SOCKET_H
+#define _UAPI_ASM_SOCKET_H
+
+#include <linux/posix_types.h>
+#include <asm/sockios.h>
+
+/*
+ * For setsockopt(2)
+ *
+ * This defines are ABI conformant as far as Linux supports these ...
+ */
+#define SOL_SOCKET	0xffff
+
+#define SO_DEBUG	0x0001	/* Record debugging information.  */
+#define SO_REUSEADDR	0x0004	/* Allow reuse of local addresses.  */
+#define SO_KEEPALIVE	0x0008	/* Keep connections alive and send
+				   SIGPIPE when they die.  */
+#define SO_DONTROUTE	0x0010	/* Don't do local routing.  */
+#define SO_BROADCAST	0x0020	/* Allow transmission of
+				   broadcast messages.	*/
+#define SO_LINGER	0x0080	/* Block on close of a reliable
+				   socket to transmit pending data.  */
+#define SO_OOBINLINE 0x0100	/* Receive out-of-band data in-band.  */
+#define SO_REUSEPORT 0x0200	/* Allow local address and port reuse.  */
+
+#define SO_TYPE		0x1008	/* Compatible name for SO_STYLE.  */
+#define SO_STYLE	SO_TYPE /* Synonym */
+#define SO_ERROR	0x1007	/* get error status and clear */
+#define SO_SNDBUF	0x1001	/* Send buffer size. */
+#define SO_RCVBUF	0x1002	/* Receive buffer. */
+#define SO_SNDLOWAT	0x1003	/* send low-water mark */
+#define SO_RCVLOWAT	0x1004	/* receive low-water mark */
+#define SO_SNDTIMEO_OLD	0x1005	/* send timeout */
+#define SO_RCVTIMEO_OLD	0x1006	/* receive timeout */
+#define SO_ACCEPTCONN	0x1009
+#define SO_PROTOCOL	0x1028	/* protocol type */
+#define SO_DOMAIN	0x1029	/* domain/socket family */
+
+/* linux-specific, might as well be the same as on i386 */
+#define SO_NO_CHECK	11
+#define SO_PRIORITY	12
+#define SO_BSDCOMPAT	14
+
+#define SO_PASSCRED	17
+#define SO_PEERCRED	18
+
+/* Security levels - as per NRL IPv6 - don't actually do anything */
+#define SO_SECURITY_AUTHENTICATION		22
+#define SO_SECURITY_ENCRYPTION_TRANSPORT	23
+#define SO_SECURITY_ENCRYPTION_NETWORK		24
+
+#define SO_BINDTODEVICE		25
+
+/* Socket filtering */
+#define SO_ATTACH_FILTER	26
+#define SO_DETACH_FILTER	27
+#define SO_GET_FILTER		SO_ATTACH_FILTER
+
+#define SO_PEERNAME		28
+
+#define SO_PEERSEC		30
+#define SO_SNDBUFFORCE		31
+#define SO_RCVBUFFORCE		33
+#define SO_PASSSEC		34
+
+#define SO_MARK			36
+
+#define SO_RXQ_OVFL		40
+
+#define SO_WIFI_STATUS		41
+#define SCM_WIFI_STATUS		SO_WIFI_STATUS
+#define SO_PEEK_OFF		42
+
+/* Instruct lower device to use last 4-bytes of skb data as FCS */
+#define SO_NOFCS		43
+
+#define SO_LOCK_FILTER		44
+
+#define SO_SELECT_ERR_QUEUE	45
+
+#define SO_BUSY_POLL		46
+
+#define SO_MAX_PACING_RATE	47
+
+#define SO_BPF_EXTENSIONS	48
+
+#define SO_INCOMING_CPU		49
+
+#define SO_ATTACH_BPF		50
+#define SO_DETACH_BPF		SO_DETACH_FILTER
+
+#define SO_ATTACH_REUSEPORT_CBPF	51
+#define SO_ATTACH_REUSEPORT_EBPF	52
+
+#define SO_CNX_ADVICE		53
+
+#define SCM_TIMESTAMPING_OPT_STATS	54
+
+#define SO_MEMINFO		55
+
+#define SO_INCOMING_NAPI_ID	56
+
+#define SO_COOKIE		57
+
+#define SCM_TIMESTAMPING_PKTINFO	58
+
+#define SO_PEERGROUPS		59
+
+#define SO_ZEROCOPY		60
+
+#define SO_TXTIME		61
+#define SCM_TXTIME		SO_TXTIME
+
+#define SO_BINDTOIFINDEX	62
+
+#define SO_TIMESTAMP_OLD        29
+#define SO_TIMESTAMPNS_OLD      35
+#define SO_TIMESTAMPING_OLD     37
+
+#define SO_TIMESTAMP_NEW        63
+#define SO_TIMESTAMPNS_NEW      64
+#define SO_TIMESTAMPING_NEW     65
+
+#define SO_RCVTIMEO_NEW         66
+#define SO_SNDTIMEO_NEW         67
+
+#define SO_DETACH_REUSEPORT_BPF 68
+
+#define SO_PREFER_BUSY_POLL	69
+#define SO_BUSY_POLL_BUDGET	70
+
+#define SO_NETNS_COOKIE		71
+
+#define SO_BUF_LOCK		72
+
+#define SO_RESERVE_MEM		73
+
+#define SO_TXREHASH		74
+
+#define SO_RCVMARK		75
+
+#if !defined(__KERNEL__)
+
+#if __BITS_PER_LONG == 64
+#define SO_TIMESTAMP		SO_TIMESTAMP_OLD
+#define SO_TIMESTAMPNS		SO_TIMESTAMPNS_OLD
+#define SO_TIMESTAMPING		SO_TIMESTAMPING_OLD
+
+#define SO_RCVTIMEO             SO_RCVTIMEO_OLD
+#define SO_SNDTIMEO             SO_SNDTIMEO_OLD
+#else
+#define SO_TIMESTAMP (sizeof(time_t) == sizeof(__kernel_long_t) ? SO_TIMESTAMP_OLD : SO_TIMESTAMP_NEW)
+#define SO_TIMESTAMPNS (sizeof(time_t) == sizeof(__kernel_long_t) ? SO_TIMESTAMPNS_OLD : SO_TIMESTAMPNS_NEW)
+#define SO_TIMESTAMPING (sizeof(time_t) == sizeof(__kernel_long_t) ? SO_TIMESTAMPING_OLD : SO_TIMESTAMPING_NEW)
+
+#define SO_RCVTIMEO (sizeof(time_t) == sizeof(__kernel_long_t) ? SO_RCVTIMEO_OLD : SO_RCVTIMEO_NEW)
+#define SO_SNDTIMEO (sizeof(time_t) == sizeof(__kernel_long_t) ? SO_SNDTIMEO_OLD : SO_SNDTIMEO_NEW)
+#endif
+
+#define SCM_TIMESTAMP           SO_TIMESTAMP
+#define SCM_TIMESTAMPNS         SO_TIMESTAMPNS
+#define SCM_TIMESTAMPING        SO_TIMESTAMPING
+
+#endif
+
+#endif /* _UAPI_ASM_SOCKET_H */
diff --git a/arch/mips/include/uapi/asm/sockios.h b/arch/mips/include/uapi/asm/sockios.h
new file mode 100644
index 000000000..66f60234f
--- /dev/null
+++ b/arch/mips/include/uapi/asm/sockios.h
@@ -0,0 +1,27 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * Socket-level I/O control calls.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995 by Ralf Baechle
+ */
+#ifndef _ASM_SOCKIOS_H
+#define _ASM_SOCKIOS_H
+
+#include <asm/ioctl.h>
+
+/* Socket-level I/O control calls. */
+#define FIOGETOWN	_IOR('f', 123, int)
+#define FIOSETOWN	_IOW('f', 124, int)
+
+#define SIOCATMARK	_IOR('s', 7, int)
+#define SIOCSPGRP	_IOW('s', 8, pid_t)
+#define SIOCGPGRP	_IOR('s', 9, pid_t)
+
+#define SIOCGSTAMP_OLD	0x8906		/* Get stamp (timeval) */
+#define SIOCGSTAMPNS_OLD 0x8907		/* Get stamp (timespec) */
+
+#endif /* _ASM_SOCKIOS_H */
diff --git a/arch/mips/include/uapi/asm/stat.h b/arch/mips/include/uapi/asm/stat.h
new file mode 100644
index 000000000..aaccdc61b
--- /dev/null
+++ b/arch/mips/include/uapi/asm/stat.h
@@ -0,0 +1,133 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995, 1999, 2000 Ralf Baechle
+ * Copyright (C) 2000 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_STAT_H
+#define _ASM_STAT_H
+
+#include <linux/types.h>
+
+#include <asm/sgidefs.h>
+
+#if (_MIPS_SIM == _MIPS_SIM_ABI32) || (_MIPS_SIM == _MIPS_SIM_NABI32)
+
+struct stat {
+	unsigned	st_dev;
+	long		st_pad1[3];		/* Reserved for network id */
+	__kernel_ino_t	st_ino;
+	__kernel_mode_t	st_mode;
+	__u32		st_nlink;
+	__kernel_uid32_t st_uid;
+	__kernel_gid32_t st_gid;
+	unsigned	st_rdev;
+	long		st_pad2[2];
+	long		st_size;
+	long		st_pad3;
+	/*
+	 * Actually this should be timestruc_t st_atime, st_mtime and st_ctime
+	 * but we don't have it under Linux.
+	 */
+	long		st_atime;
+	long		st_atime_nsec;
+	long		st_mtime;
+	long		st_mtime_nsec;
+	long		st_ctime;
+	long		st_ctime_nsec;
+	long		st_blksize;
+	long		st_blocks;
+	long		st_pad4[14];
+};
+
+/*
+ * This matches struct stat64 in glibc2.1, hence the absolutely insane
+ * amounts of padding around dev_t's.  The memory layout is the same as of
+ * struct stat of the 64-bit kernel.
+ */
+
+struct stat64 {
+	unsigned long	st_dev;
+	unsigned long	st_pad0[3];	/* Reserved for st_dev expansion  */
+
+	unsigned long long	st_ino;
+
+	__kernel_mode_t	st_mode;
+	__u32		st_nlink;
+
+	__kernel_uid32_t st_uid;
+	__kernel_gid32_t st_gid;
+
+	unsigned long	st_rdev;
+	unsigned long	st_pad1[3];	/* Reserved for st_rdev expansion  */
+
+	long long	st_size;
+
+	/*
+	 * Actually this should be timestruc_t st_atime, st_mtime and st_ctime
+	 * but we don't have it under Linux.
+	 */
+	long		st_atime;
+	unsigned long	st_atime_nsec;	/* Reserved for st_atime expansion  */
+
+	long		st_mtime;
+	unsigned long	st_mtime_nsec;	/* Reserved for st_mtime expansion  */
+
+	long		st_ctime;
+	unsigned long	st_ctime_nsec;	/* Reserved for st_ctime expansion  */
+
+	unsigned long	st_blksize;
+	unsigned long	st_pad2;
+
+	long long	st_blocks;
+};
+
+#endif /* _MIPS_SIM == _MIPS_SIM_ABI32 */
+
+#if _MIPS_SIM == _MIPS_SIM_ABI64
+
+/* The memory layout is the same as of struct stat64 of the 32-bit kernel.  */
+struct stat {
+	unsigned int		st_dev;
+	unsigned int		st_pad0[3]; /* Reserved for st_dev expansion */
+
+	unsigned long		st_ino;
+
+	__kernel_mode_t		st_mode;
+	__u32			st_nlink;
+
+	__kernel_uid32_t	st_uid;
+	__kernel_gid32_t	st_gid;
+
+	unsigned int		st_rdev;
+	unsigned int		st_pad1[3]; /* Reserved for st_rdev expansion */
+
+	long			st_size;
+
+	/*
+	 * Actually this should be timestruc_t st_atime, st_mtime and st_ctime
+	 * but we don't have it under Linux.
+	 */
+	unsigned int		st_atime;
+	unsigned int		st_atime_nsec;
+
+	unsigned int		st_mtime;
+	unsigned int		st_mtime_nsec;
+
+	unsigned int		st_ctime;
+	unsigned int		st_ctime_nsec;
+
+	unsigned int		st_blksize;
+	unsigned int		st_pad2;
+
+	unsigned long		st_blocks;
+};
+
+#endif /* _MIPS_SIM == _MIPS_SIM_ABI64 */
+
+#define STAT_HAVE_NSEC 1
+
+#endif /* _ASM_STAT_H */
diff --git a/arch/mips/include/uapi/asm/statfs.h b/arch/mips/include/uapi/asm/statfs.h
new file mode 100644
index 000000000..f4174dcae
--- /dev/null
+++ b/arch/mips/include/uapi/asm/statfs.h
@@ -0,0 +1,101 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995, 1999 by Ralf Baechle
+ */
+#ifndef _ASM_STATFS_H
+#define _ASM_STATFS_H
+
+#include <linux/posix_types.h>
+#include <asm/sgidefs.h>
+
+#ifndef __KERNEL_STRICT_NAMES
+
+#include <linux/types.h>
+
+typedef __kernel_fsid_t	       fsid_t;
+
+#endif
+
+struct statfs {
+	long		f_type;
+#define f_fstyp f_type
+	long		f_bsize;
+	long		f_frsize;	/* Fragment size - unsupported */
+	long		f_blocks;
+	long		f_bfree;
+	long		f_files;
+	long		f_ffree;
+	long		f_bavail;
+
+	/* Linux specials */
+	__kernel_fsid_t f_fsid;
+	long		f_namelen;
+	long		f_flags;
+	long		f_spare[5];
+};
+
+#if (_MIPS_SIM == _MIPS_SIM_ABI32) || (_MIPS_SIM == _MIPS_SIM_NABI32)
+
+/*
+ * Unlike the traditional version the LFAPI version has none of the ABI junk
+ */
+struct statfs64 {
+	__u32	f_type;
+	__u32	f_bsize;
+	__u32	f_frsize;	/* Fragment size - unsupported */
+	__u32	__pad;
+	__u64	f_blocks;
+	__u64	f_bfree;
+	__u64	f_files;
+	__u64	f_ffree;
+	__u64	f_bavail;
+	__kernel_fsid_t f_fsid;
+	__u32	f_namelen;
+	__u32	f_flags;
+	__u32	f_spare[5];
+};
+
+#endif /* _MIPS_SIM == _MIPS_SIM_ABI32 */
+
+#if _MIPS_SIM == _MIPS_SIM_ABI64
+
+struct statfs64 {			/* Same as struct statfs */
+	long		f_type;
+	long		f_bsize;
+	long		f_frsize;	/* Fragment size - unsupported */
+	long		f_blocks;
+	long		f_bfree;
+	long		f_files;
+	long		f_ffree;
+	long		f_bavail;
+
+	/* Linux specials */
+	__kernel_fsid_t f_fsid;
+	long		f_namelen;
+	long		f_flags;
+	long		f_spare[5];
+};
+
+struct compat_statfs64 {
+	__u32	f_type;
+	__u32	f_bsize;
+	__u32	f_frsize;	/* Fragment size - unsupported */
+	__u32	__pad;
+	__u64	f_blocks;
+	__u64	f_bfree;
+	__u64	f_files;
+	__u64	f_ffree;
+	__u64	f_bavail;
+	__kernel_fsid_t f_fsid;
+	__u32	f_namelen;
+	__u32	f_flags;
+	__u32	f_spare[5];
+};
+
+#endif /* _MIPS_SIM == _MIPS_SIM_ABI64 */
+
+#endif /* _ASM_STATFS_H */
diff --git a/arch/mips/include/uapi/asm/swab.h b/arch/mips/include/uapi/asm/swab.h
new file mode 100644
index 000000000..d6795fe4e
--- /dev/null
+++ b/arch/mips/include/uapi/asm/swab.h
@@ -0,0 +1,71 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1996, 99, 2003 by Ralf Baechle
+ */
+#ifndef _ASM_SWAB_H
+#define _ASM_SWAB_H
+
+#include <linux/compiler.h>
+#include <linux/types.h>
+
+#define __SWAB_64_THRU_32__
+
+#if !defined(__mips16) &&					\
+	((defined(__mips_isa_rev) && (__mips_isa_rev >= 2)) ||	\
+	 defined(_MIPS_ARCH_LOONGSON3A))
+
+static inline __attribute_const__ __u16 __arch_swab16(__u16 x)
+{
+	__asm__(
+	"	.set	push			\n"
+	"	.set	arch=mips32r2		\n"
+	"	wsbh	%0, %1			\n"
+	"	.set	pop			\n"
+	: "=r" (x)
+	: "r" (x));
+
+	return x;
+}
+#define __arch_swab16 __arch_swab16
+
+static inline __attribute_const__ __u32 __arch_swab32(__u32 x)
+{
+	__asm__(
+	"	.set	push			\n"
+	"	.set	arch=mips32r2		\n"
+	"	wsbh	%0, %1			\n"
+	"	rotr	%0, %0, 16		\n"
+	"	.set	pop			\n"
+	: "=r" (x)
+	: "r" (x));
+
+	return x;
+}
+#define __arch_swab32 __arch_swab32
+
+/*
+ * Having already checked for MIPS R2, enable the optimized version for
+ * 64-bit kernel on r2 CPUs.
+ */
+#ifdef __mips64
+static inline __attribute_const__ __u64 __arch_swab64(__u64 x)
+{
+	__asm__(
+	"	.set	push			\n"
+	"	.set	arch=mips64r2		\n"
+	"	dsbh	%0, %1			\n"
+	"	dshd	%0, %0			\n"
+	"	.set	pop			\n"
+	: "=r" (x)
+	: "r" (x));
+
+	return x;
+}
+#define __arch_swab64 __arch_swab64
+#endif /* __mips64 */
+#endif /* (not __mips16) and (MIPS R2 or newer or Loongson 3A) */
+#endif /* _ASM_SWAB_H */
diff --git a/arch/mips/include/uapi/asm/sysmips.h b/arch/mips/include/uapi/asm/sysmips.h
new file mode 100644
index 000000000..4c009e10d
--- /dev/null
+++ b/arch/mips/include/uapi/asm/sysmips.h
@@ -0,0 +1,26 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * Definitions for the MIPS sysmips(2) call
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995 by Ralf Baechle
+ */
+#ifndef _ASM_SYSMIPS_H
+#define _ASM_SYSMIPS_H
+
+/*
+ * Commands for the sysmips(2) call
+ *
+ * sysmips(2) is deprecated - though some existing software uses it.
+ * We only support the following commands.
+ */
+#define SETNAME			   1	/* set hostname			 */
+#define FLUSH_CACHE		   3	/* writeback and invalidate caches */
+#define MIPS_FIXADE		   7	/* control address error fixing	 */
+#define MIPS_RDNVRAM		  10	/* read NVRAM */
+#define MIPS_ATOMIC_SET		2001	/* atomically set variable	 */
+
+#endif /* _ASM_SYSMIPS_H */
diff --git a/arch/mips/include/uapi/asm/termbits.h b/arch/mips/include/uapi/asm/termbits.h
new file mode 100644
index 000000000..1eb60903d
--- /dev/null
+++ b/arch/mips/include/uapi/asm/termbits.h
@@ -0,0 +1,177 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995, 96, 99, 2001, 06 Ralf Baechle
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ * Copyright (C) 2001 MIPS Technologies, Inc.
+ */
+#ifndef _ASM_TERMBITS_H
+#define _ASM_TERMBITS_H
+
+#include <asm-generic/termbits-common.h>
+
+typedef unsigned int	tcflag_t;
+
+/*
+ * The ABI says nothing about NCC but seems to use NCCS as
+ * replacement for it in struct termio
+ */
+#define NCCS	23
+struct termios {
+	tcflag_t c_iflag;		/* input mode flags */
+	tcflag_t c_oflag;		/* output mode flags */
+	tcflag_t c_cflag;		/* control mode flags */
+	tcflag_t c_lflag;		/* local mode flags */
+	cc_t c_line;			/* line discipline */
+	cc_t c_cc[NCCS];		/* control characters */
+};
+
+struct termios2 {
+	tcflag_t c_iflag;		/* input mode flags */
+	tcflag_t c_oflag;		/* output mode flags */
+	tcflag_t c_cflag;		/* control mode flags */
+	tcflag_t c_lflag;		/* local mode flags */
+	cc_t c_line;			/* line discipline */
+	cc_t c_cc[NCCS];		/* control characters */
+	speed_t c_ispeed;		/* input speed */
+	speed_t c_ospeed;		/* output speed */
+};
+
+struct ktermios {
+	tcflag_t c_iflag;		/* input mode flags */
+	tcflag_t c_oflag;		/* output mode flags */
+	tcflag_t c_cflag;		/* control mode flags */
+	tcflag_t c_lflag;		/* local mode flags */
+	cc_t c_line;			/* line discipline */
+	cc_t c_cc[NCCS];		/* control characters */
+	speed_t c_ispeed;		/* input speed */
+	speed_t c_ospeed;		/* output speed */
+};
+
+/* c_cc characters */
+#define VINTR		 0		/* Interrupt character [ISIG] */
+#define VQUIT		 1		/* Quit character [ISIG] */
+#define VERASE		 2		/* Erase character [ICANON] */
+#define VKILL		 3		/* Kill-line character [ICANON] */
+#define VMIN		 4		/* Minimum number of bytes read at once [!ICANON] */
+#define VTIME		 5		/* Time-out value (tenths of a second) [!ICANON] */
+#define VEOL2		 6		/* Second EOL character [ICANON] */
+#define VSWTC		 7		/* ??? */
+#define VSWTCH		VSWTC
+#define VSTART		 8		/* Start (X-ON) character [IXON, IXOFF] */
+#define VSTOP		 9		/* Stop (X-OFF) character [IXON, IXOFF] */
+#define VSUSP		10		/* Suspend character [ISIG] */
+#if 0
+/*
+ * VDSUSP is not supported
+ */
+#define VDSUSP		11		/* Delayed suspend character [ISIG] */
+#endif
+#define VREPRINT	12		/* Reprint-line character [ICANON] */
+#define VDISCARD	13		/* Discard character [IEXTEN] */
+#define VWERASE		14		/* Word-erase character [ICANON] */
+#define VLNEXT		15		/* Literal-next character [IEXTEN] */
+#define VEOF		16		/* End-of-file character [ICANON] */
+#define VEOL		17		/* End-of-line character [ICANON] */
+
+/* c_iflag bits */
+#define IUCLC	0x0200		/* Map upper case to lower case on input */
+#define IXON	0x0400		/* Enable start/stop output control */
+#define IXOFF	0x1000		/* Enable start/stop input control */
+#define IMAXBEL	0x2000		/* Ring bell when input queue is full */
+#define IUTF8	0x4000		/* Input is UTF-8 */
+
+/* c_oflag bits */
+#define OLCUC	0x00002		/* Map lower case to upper case on output */
+#define ONLCR	0x00004		/* Map NL to CR-NL on output */
+#define NLDLY	0x00100
+#define   NL0	0x00000
+#define   NL1	0x00100
+#define CRDLY	0x00600
+#define   CR0	0x00000
+#define   CR1	0x00200
+#define   CR2	0x00400
+#define   CR3	0x00600
+#define TABDLY	0x01800
+#define   TAB0	0x00000
+#define   TAB1	0x00800
+#define   TAB2	0x01000
+#define   TAB3	0x01800
+#define   XTABS	0x01800
+#define BSDLY	0x02000
+#define   BS0	0x00000
+#define   BS1	0x02000
+#define VTDLY	0x04000
+#define   VT0	0x00000
+#define   VT1	0x04000
+#define FFDLY	0x08000
+#define   FF0	0x00000
+#define   FF1	0x08000
+/*
+#define PAGEOUT ???
+#define WRAP	???
+ */
+
+/* c_cflag bit meaning */
+#define CBAUD		0x0000100f
+#define CSIZE		0x00000030	/* Number of bits per byte (mask) */
+#define   CS5		0x00000000	/* 5 bits per byte */
+#define   CS6		0x00000010	/* 6 bits per byte */
+#define   CS7		0x00000020	/* 7 bits per byte */
+#define   CS8		0x00000030	/* 8 bits per byte */
+#define CSTOPB		0x00000040	/* Two stop bits instead of one */
+#define CREAD		0x00000080	/* Enable receiver */
+#define PARENB		0x00000100	/* Parity enable */
+#define PARODD		0x00000200	/* Odd parity instead of even */
+#define HUPCL		0x00000400	/* Hang up on last close */
+#define CLOCAL		0x00000800	/* Ignore modem status lines */
+#define CBAUDEX		0x00001000
+#define BOTHER		0x00001000
+#define     B57600	0x00001001
+#define    B115200	0x00001002
+#define    B230400	0x00001003
+#define    B460800	0x00001004
+#define    B500000	0x00001005
+#define    B576000	0x00001006
+#define    B921600	0x00001007
+#define   B1000000	0x00001008
+#define   B1152000	0x00001009
+#define   B1500000	0x0000100a
+#define   B2000000	0x0000100b
+#define   B2500000	0x0000100c
+#define   B3000000	0x0000100d
+#define   B3500000	0x0000100e
+#define   B4000000	0x0000100f
+#define CIBAUD		0x100f0000	/* input baud rate */
+
+/* c_lflag bits */
+#define ISIG	0x00001		/* Enable signals */
+#define ICANON	0x00002		/* Do erase and kill processing */
+#define XCASE	0x00004
+#define ECHO	0x00008		/* Enable echo */
+#define ECHOE	0x00010		/* Visual erase for ERASE */
+#define ECHOK	0x00020		/* Echo NL after KILL */
+#define ECHONL	0x00040		/* Echo NL even if ECHO is off */
+#define NOFLSH	0x00080		/* Disable flush after interrupt */
+#define IEXTEN	0x00100		/* Enable DISCARD and LNEXT */
+#define ECHOCTL	0x00200		/* Echo control characters as ^X */
+#define ECHOPRT	0x00400		/* Hardcopy visual erase */
+#define ECHOKE	0x00800		/* Visual erase for KILL */
+#define FLUSHO	0x02000
+#define PENDIN	0x04000		/* Retype pending input (state) */
+#define TOSTOP	0x08000		/* Send SIGTTOU for background output */
+#define ITOSTOP	TOSTOP
+#define EXTPROC	0x10000		/* External processing on pty */
+
+/* ioctl (fd, TIOCSERGETLSR, &result) where result may be as below */
+#define TIOCSER_TEMT	0x01	/* Transmitter physically empty */
+
+/* tcsetattr uses these */
+#define TCSANOW		TCSETS	/* Change immediately */
+#define TCSADRAIN	TCSETSW /* Change when pending output is written */
+#define TCSAFLUSH	TCSETSF /* Flush pending input before changing */
+
+#endif /* _ASM_TERMBITS_H */
diff --git a/arch/mips/include/uapi/asm/termios.h b/arch/mips/include/uapi/asm/termios.h
new file mode 100644
index 000000000..d6c576794
--- /dev/null
+++ b/arch/mips/include/uapi/asm/termios.h
@@ -0,0 +1,81 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995, 1996, 2000, 2001 by Ralf Baechle
+ * Copyright (C) 2000, 2001 Silicon Graphics, Inc.
+ */
+#ifndef _UAPI_ASM_TERMIOS_H
+#define _UAPI_ASM_TERMIOS_H
+
+#include <linux/errno.h>
+#include <asm/termbits.h>
+#include <asm/ioctls.h>
+
+struct sgttyb {
+	char	sg_ispeed;
+	char	sg_ospeed;
+	char	sg_erase;
+	char	sg_kill;
+	int	sg_flags;	/* SGI special - int, not short */
+};
+
+struct tchars {
+	char	t_intrc;
+	char	t_quitc;
+	char	t_startc;
+	char	t_stopc;
+	char	t_eofc;
+	char	t_brkc;
+};
+
+struct ltchars {
+	char	t_suspc;	/* stop process signal */
+	char	t_dsuspc;	/* delayed stop process signal */
+	char	t_rprntc;	/* reprint line */
+	char	t_flushc;	/* flush output (toggles) */
+	char	t_werasc;	/* word erase */
+	char	t_lnextc;	/* literal next character */
+};
+
+/* TIOCGSIZE, TIOCSSIZE not defined yet.  Only needed for SunOS source
+   compatibility anyway ... */
+
+struct winsize {
+	unsigned short ws_row;
+	unsigned short ws_col;
+	unsigned short ws_xpixel;
+	unsigned short ws_ypixel;
+};
+
+#define NCC	8
+struct termio {
+	unsigned short c_iflag;		/* input mode flags */
+	unsigned short c_oflag;		/* output mode flags */
+	unsigned short c_cflag;		/* control mode flags */
+	unsigned short c_lflag;		/* local mode flags */
+	char c_line;			/* line discipline */
+	unsigned char c_cc[NCCS];	/* control characters */
+};
+
+
+/* modem lines */
+#define TIOCM_LE	0x001		/* line enable */
+#define TIOCM_DTR	0x002		/* data terminal ready */
+#define TIOCM_RTS	0x004		/* request to send */
+#define TIOCM_ST	0x010		/* secondary transmit */
+#define TIOCM_SR	0x020		/* secondary receive */
+#define TIOCM_CTS	0x040		/* clear to send */
+#define TIOCM_CAR	0x100		/* carrier detect */
+#define TIOCM_CD	TIOCM_CAR
+#define TIOCM_RNG	0x200		/* ring */
+#define TIOCM_RI	TIOCM_RNG
+#define TIOCM_DSR	0x400		/* data set ready */
+#define TIOCM_OUT1	0x2000
+#define TIOCM_OUT2	0x4000
+#define TIOCM_LOOP	0x8000
+
+
+#endif /* _UAPI_ASM_TERMIOS_H */
diff --git a/arch/mips/include/uapi/asm/types.h b/arch/mips/include/uapi/asm/types.h
new file mode 100644
index 000000000..6b2150484
--- /dev/null
+++ b/arch/mips/include/uapi/asm/types.h
@@ -0,0 +1,31 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994, 1995, 1996, 1999 by Ralf Baechle
+ * Copyright (C) 2008 Wind River Systems,
+ *   written by Ralf Baechle
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ */
+#ifndef _UAPI_ASM_TYPES_H
+#define _UAPI_ASM_TYPES_H
+
+/*
+ * We don't use int-l64.h for the kernel anymore but still use it for
+ * userspace to avoid code changes.
+ *
+ * However, some user programs (e.g. perf) may not want this. They can
+ * flag __SANE_USERSPACE_TYPES__ to get int-ll64.h here.
+ */
+#ifndef __KERNEL__
+# if _MIPS_SZLONG == 64 && !defined(__SANE_USERSPACE_TYPES__)
+#  include <asm-generic/int-l64.h>
+# else
+#  include <asm-generic/int-ll64.h>
+# endif
+#endif
+
+
+#endif /* _UAPI_ASM_TYPES_H */
diff --git a/arch/mips/include/uapi/asm/ucontext.h b/arch/mips/include/uapi/asm/ucontext.h
new file mode 100644
index 000000000..6122ef97c
--- /dev/null
+++ b/arch/mips/include/uapi/asm/ucontext.h
@@ -0,0 +1,66 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+#ifndef __MIPS_UAPI_ASM_UCONTEXT_H
+#define __MIPS_UAPI_ASM_UCONTEXT_H
+
+/**
+ * struct extcontext - extended context header structure
+ * @magic:	magic value identifying the type of extended context
+ * @size:	the size in bytes of the enclosing structure
+ *
+ * Extended context structures provide context which does not fit within struct
+ * sigcontext. They are placed sequentially in memory at the end of struct
+ * ucontext and struct sigframe, with each extended context structure beginning
+ * with a header defined by this struct. The type of context represented is
+ * indicated by the magic field. Userland may check each extended context
+ * structure against magic values that it recognises. The size field allows any
+ * unrecognised context to be skipped, allowing for future expansion. The end
+ * of the extended context data is indicated by the magic value
+ * END_EXTCONTEXT_MAGIC.
+ */
+struct extcontext {
+	unsigned int		magic;
+	unsigned int		size;
+};
+
+/**
+ * struct msa_extcontext - MSA extended context structure
+ * @ext:	the extended context header, with magic == MSA_EXTCONTEXT_MAGIC
+ * @wr:		the most significant 64 bits of each MSA vector register
+ * @csr:	the value of the MSA control & status register
+ *
+ * If MSA context is live for a task at the time a signal is delivered to it,
+ * this structure will hold the MSA context of the task as it was prior to the
+ * signal delivery.
+ */
+struct msa_extcontext {
+	struct extcontext	ext;
+#define MSA_EXTCONTEXT_MAGIC	0x784d5341	/* xMSA */
+
+	unsigned long long	wr[32];
+	unsigned int		csr;
+};
+
+#define END_EXTCONTEXT_MAGIC	0x78454e44	/* xEND */
+
+/**
+ * struct ucontext - user context structure
+ * @uc_flags:
+ * @uc_link:
+ * @uc_stack:
+ * @uc_mcontext:	holds basic processor state
+ * @uc_sigmask:
+ * @uc_extcontext:	holds extended processor state
+ */
+struct ucontext {
+	/* Historic fields matching asm-generic */
+	unsigned long		uc_flags;
+	struct ucontext		*uc_link;
+	stack_t			uc_stack;
+	struct sigcontext	uc_mcontext;
+	sigset_t		uc_sigmask;
+
+	/* Extended context structures may follow ucontext */
+	unsigned long long	uc_extcontext[];
+};
+
+#endif /* __MIPS_UAPI_ASM_UCONTEXT_H */
diff --git a/arch/mips/include/uapi/asm/unistd.h b/arch/mips/include/uapi/asm/unistd.h
new file mode 100644
index 000000000..4abe38754
--- /dev/null
+++ b/arch/mips/include/uapi/asm/unistd.h
@@ -0,0 +1,39 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995, 96, 97, 98, 99, 2000 by Ralf Baechle
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ *
+ * Changed system calls macros _syscall5 - _syscall7 to push args 5 to 7 onto
+ * the stack. Robin Farine for ACN S.A, Copyright (C) 1996 by ACN S.A
+ */
+#ifndef _UAPI_ASM_UNISTD_H
+#define _UAPI_ASM_UNISTD_H
+
+#include <asm/sgidefs.h>
+
+#if _MIPS_SIM == _MIPS_SIM_ABI32
+
+#define __NR_Linux	4000
+#include <asm/unistd_o32.h>
+
+#endif /* _MIPS_SIM == _MIPS_SIM_ABI32 */
+
+#if _MIPS_SIM == _MIPS_SIM_ABI64
+
+#define __NR_Linux	5000
+#include <asm/unistd_n64.h>
+
+#endif /* _MIPS_SIM == _MIPS_SIM_ABI64 */
+
+#if _MIPS_SIM == _MIPS_SIM_NABI32
+
+#define __NR_Linux	6000
+#include <asm/unistd_n32.h>
+
+#endif /* _MIPS_SIM == _MIPS_SIM_NABI32 */
+
+#endif /* _UAPI_ASM_UNISTD_H */
diff --git a/arch/mips/ingenic/Kconfig b/arch/mips/ingenic/Kconfig
new file mode 100644
index 000000000..f595b339a
--- /dev/null
+++ b/arch/mips/ingenic/Kconfig
@@ -0,0 +1,78 @@
+# SPDX-License-Identifier: GPL-2.0
+
+config MACH_INGENIC_GENERIC
+	bool
+	select MACH_INGENIC
+	select MACH_JZ4740
+	select MACH_JZ4725B
+	select MACH_JZ4770
+	select MACH_JZ4780
+	select MACH_X1000
+	select MACH_X1830
+
+choice
+	prompt "Machine type"
+	depends on MACH_INGENIC_SOC
+	default INGENIC_GENERIC_BOARD
+
+config INGENIC_GENERIC_BOARD
+	bool "Generic board"
+	select MACH_INGENIC_GENERIC
+
+config JZ4740_QI_LB60
+	bool "Qi Hardware Ben NanoNote"
+	select MACH_JZ4740
+
+config JZ4740_RS90
+	bool "YLM RetroMini (RS-90)"
+	select MACH_JZ4725B
+
+config JZ4770_GCW0
+	bool "Game Consoles Worldwide GCW Zero"
+	select MACH_JZ4770
+
+config JZ4780_CI20
+	bool "MIPS Creator CI20"
+	select MACH_JZ4780
+
+config X1000_CU1000_NEO
+	bool "YSH & ATIL CU1000 Module with Neo backplane"
+	select MACH_X1000
+
+config X1830_CU1830_NEO
+	bool "YSH & ATIL CU1830 Module with Neo backplane"
+	select MACH_X1830
+
+endchoice
+
+config MACH_JZ4725B
+	bool
+	select SYS_HAS_CPU_MIPS32_R1
+
+config MACH_JZ4740
+	bool
+	select SYS_HAS_CPU_MIPS32_R1
+
+config MACH_JZ4770
+	bool
+	select MIPS_CPU_SCACHE
+	select SYS_HAS_CPU_MIPS32_R2
+	select SYS_SUPPORTS_HIGHMEM
+
+config MACH_JZ4780
+	bool
+	select MIPS_CPU_SCACHE
+	select SYS_HAS_CPU_MIPS32_R2
+	select SYS_SUPPORTS_HIGHMEM
+
+config MACH_X1000
+	bool
+	select MIPS_CPU_SCACHE
+	select SYS_HAS_CPU_MIPS32_R2
+	select SYS_SUPPORTS_HIGHMEM
+
+config MACH_X1830
+	bool
+	select MIPS_CPU_SCACHE
+	select SYS_HAS_CPU_MIPS32_R2
+	select SYS_SUPPORTS_HIGHMEM
diff --git a/arch/mips/jazz/Kconfig b/arch/mips/jazz/Kconfig
new file mode 100644
index 000000000..42932ca98
--- /dev/null
+++ b/arch/mips/jazz/Kconfig
@@ -0,0 +1,31 @@
+# SPDX-License-Identifier: GPL-2.0
+config ACER_PICA_61
+	bool "Support for Acer PICA 1 chipset"
+	depends on MACH_JAZZ
+	select DMA_NONCOHERENT
+	help
+	  This is a machine with a R4400 133/150 MHz CPU. To compile a Linux
+	  kernel that runs on these, say Y here. For details about Linux on
+	  the MIPS architecture, check out the Linux/MIPS FAQ on the WWW at
+	  <http://www.linux-mips.org/>.
+
+config MIPS_MAGNUM_4000
+	bool "Support for MIPS Magnum 4000"
+	depends on MACH_JAZZ
+	select DMA_NONCOHERENT
+	select SYS_SUPPORTS_BIG_ENDIAN
+	help
+	  This is a machine with a R4000 100 MHz CPU. To compile a Linux
+	  kernel that runs on these, say Y here. For details about Linux on
+	  the MIPS architecture, check out the Linux/MIPS FAQ on the WWW at
+	  <http://www.linux-mips.org/>.
+
+config OLIVETTI_M700
+	bool "Support for Olivetti M700-10"
+	depends on MACH_JAZZ
+	select DMA_NONCOHERENT
+	help
+	  This is a machine with a R4000 100 MHz CPU. To compile a Linux
+	  kernel that runs on these, say Y here. For details about Linux on
+	  the MIPS architecture, check out the Linux/MIPS FAQ on the WWW at
+	  <http://www.linux-mips.org/>.
diff --git a/arch/mips/jazz/Makefile b/arch/mips/jazz/Makefile
new file mode 100644
index 000000000..5815e1cb3
--- /dev/null
+++ b/arch/mips/jazz/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Makefile for the Jazz family specific parts of the kernel
+#
+
+obj-y		:= irq.o jazzdma.o reset.o setup.o
diff --git a/arch/mips/jazz/Platform b/arch/mips/jazz/Platform
new file mode 100644
index 000000000..eb0490ae8
--- /dev/null
+++ b/arch/mips/jazz/Platform
@@ -0,0 +1,5 @@
+#
+# Acer PICA 61, Mips Magnum 4000 and Olivetti M700.
+#
+cflags-$(CONFIG_MACH_JAZZ)	+= -I$(srctree)/arch/mips/include/asm/mach-jazz
+load-$(CONFIG_MACH_JAZZ)	+= 0xffffffff80080000
diff --git a/arch/mips/jazz/irq.c b/arch/mips/jazz/irq.c
new file mode 100644
index 000000000..264d45387
--- /dev/null
+++ b/arch/mips/jazz/irq.c
@@ -0,0 +1,149 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1992 Linus Torvalds
+ * Copyright (C) 1994 - 2001, 2003, 07 Ralf Baechle
+ */
+#include <linux/clockchips.h>
+#include <linux/i8253.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/smp.h>
+#include <linux/spinlock.h>
+#include <linux/irq.h>
+#include <linux/pgtable.h>
+
+#include <asm/irq_cpu.h>
+#include <asm/i8259.h>
+#include <asm/io.h>
+#include <asm/jazz.h>
+#include <asm/tlbmisc.h>
+
+static DEFINE_RAW_SPINLOCK(r4030_lock);
+
+static void enable_r4030_irq(struct irq_data *d)
+{
+	unsigned int mask = 1 << (d->irq - JAZZ_IRQ_START);
+	unsigned long flags;
+
+	raw_spin_lock_irqsave(&r4030_lock, flags);
+	mask |= r4030_read_reg16(JAZZ_IO_IRQ_ENABLE);
+	r4030_write_reg16(JAZZ_IO_IRQ_ENABLE, mask);
+	raw_spin_unlock_irqrestore(&r4030_lock, flags);
+}
+
+void disable_r4030_irq(struct irq_data *d)
+{
+	unsigned int mask = ~(1 << (d->irq - JAZZ_IRQ_START));
+	unsigned long flags;
+
+	raw_spin_lock_irqsave(&r4030_lock, flags);
+	mask &= r4030_read_reg16(JAZZ_IO_IRQ_ENABLE);
+	r4030_write_reg16(JAZZ_IO_IRQ_ENABLE, mask);
+	raw_spin_unlock_irqrestore(&r4030_lock, flags);
+}
+
+static struct irq_chip r4030_irq_type = {
+	.name = "R4030",
+	.irq_mask = disable_r4030_irq,
+	.irq_unmask = enable_r4030_irq,
+};
+
+void __init init_r4030_ints(void)
+{
+	int i;
+
+	for (i = JAZZ_IRQ_START; i <= JAZZ_IRQ_END; i++)
+		irq_set_chip_and_handler(i, &r4030_irq_type, handle_level_irq);
+
+	r4030_write_reg16(JAZZ_IO_IRQ_ENABLE, 0);
+	r4030_read_reg16(JAZZ_IO_IRQ_SOURCE);		/* clear pending IRQs */
+	r4030_read_reg32(JAZZ_R4030_INVAL_ADDR);	/* clear error bits */
+}
+
+/*
+ * On systems with i8259-style interrupt controllers we assume for
+ * driver compatibility reasons interrupts 0 - 15 to be the i8259
+ * interrupts even if the hardware uses a different interrupt numbering.
+ */
+void __init arch_init_irq(void)
+{
+	/*
+	 * this is a hack to get back the still needed wired mapping
+	 * killed by init_mm()
+	 */
+
+	/* Map 0xe0000000 -> 0x0:800005C0, 0xe0010000 -> 0x1:30000580 */
+	add_wired_entry(0x02000017, 0x03c00017, 0xe0000000, PM_64K);
+	/* Map 0xe2000000 -> 0x0:900005C0, 0xe3010000 -> 0x0:910005C0 */
+	add_wired_entry(0x02400017, 0x02440017, 0xe2000000, PM_16M);
+	/* Map 0xe4000000 -> 0x0:600005C0, 0xe4100000 -> 400005C0 */
+	add_wired_entry(0x01800017, 0x01000017, 0xe4000000, PM_4M);
+
+	init_i8259_irqs();			/* Integrated i8259  */
+	mips_cpu_irq_init();
+	init_r4030_ints();
+
+	change_c0_status(ST0_IM, IE_IRQ2 | IE_IRQ1);
+}
+
+asmlinkage void plat_irq_dispatch(void)
+{
+	unsigned int pending = read_c0_cause() & read_c0_status();
+	unsigned int irq;
+
+	if (pending & IE_IRQ4) {
+		r4030_read_reg32(JAZZ_TIMER_REGISTER);
+		do_IRQ(JAZZ_TIMER_IRQ);
+	} else if (pending & IE_IRQ2) {
+		irq = *(volatile u8 *)JAZZ_EISA_IRQ_ACK;
+		do_IRQ(irq);
+	} else if (pending & IE_IRQ1) {
+		irq = *(volatile u8 *)JAZZ_IO_IRQ_SOURCE >> 2;
+		if (likely(irq > 0))
+			do_IRQ(irq + JAZZ_IRQ_START - 1);
+		else
+			panic("Unimplemented loc_no_irq handler");
+	}
+}
+
+struct clock_event_device r4030_clockevent = {
+	.name		= "r4030",
+	.features	= CLOCK_EVT_FEAT_PERIODIC,
+	.rating		= 300,
+	.irq		= JAZZ_TIMER_IRQ,
+};
+
+static irqreturn_t r4030_timer_interrupt(int irq, void *dev_id)
+{
+	struct clock_event_device *cd = dev_id;
+
+	cd->event_handler(cd);
+	return IRQ_HANDLED;
+}
+
+void __init plat_time_init(void)
+{
+	struct clock_event_device *cd = &r4030_clockevent;
+	unsigned int cpu = smp_processor_id();
+
+	BUG_ON(HZ != 100);
+
+	cd->cpumask		= cpumask_of(cpu);
+	clockevents_register_device(cd);
+	if (request_irq(JAZZ_TIMER_IRQ, r4030_timer_interrupt, IRQF_TIMER,
+			"R4030 timer", cd))
+		pr_err("Failed to register R4030 timer interrupt\n");
+
+	/*
+	 * Set clock to 100Hz.
+	 *
+	 * The R4030 timer receives an input clock of 1kHz which is divided by
+	 * a programmable 4-bit divider.  This makes it fairly inflexible.
+	 */
+	r4030_write_reg32(JAZZ_TIMER_INTERVAL, 9);
+	setup_pit_timer();
+}
diff --git a/arch/mips/jazz/jazzdma.c b/arch/mips/jazz/jazzdma.c
new file mode 100644
index 000000000..eabddb89d
--- /dev/null
+++ b/arch/mips/jazz/jazzdma.c
@@ -0,0 +1,623 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Mips Jazz DMA controller support
+ * Copyright (C) 1995, 1996 by Andreas Busse
+ *
+ * NOTE: Some of the argument checking could be removed when
+ * things have settled down. Also, instead of returning 0xffffffff
+ * on failure of vdma_alloc() one could leave page #0 unused
+ * and return the more usual NULL pointer as logical address.
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/export.h>
+#include <linux/errno.h>
+#include <linux/mm.h>
+#include <linux/memblock.h>
+#include <linux/spinlock.h>
+#include <linux/gfp.h>
+#include <linux/dma-map-ops.h>
+#include <asm/mipsregs.h>
+#include <asm/jazz.h>
+#include <asm/io.h>
+#include <linux/uaccess.h>
+#include <asm/dma.h>
+#include <asm/jazzdma.h>
+
+/*
+ * Set this to one to enable additional vdma debug code.
+ */
+#define CONF_DEBUG_VDMA 0
+
+static VDMA_PGTBL_ENTRY *pgtbl;
+
+static DEFINE_SPINLOCK(vdma_lock);
+
+/*
+ * Debug stuff
+ */
+#define vdma_debug     ((CONF_DEBUG_VDMA) ? debuglvl : 0)
+
+static int debuglvl = 3;
+
+/*
+ * Initialize the pagetable with a one-to-one mapping of
+ * the first 16 Mbytes of main memory and declare all
+ * entries to be unused. Using this method will at least
+ * allow some early device driver operations to work.
+ */
+static inline void vdma_pgtbl_init(void)
+{
+	unsigned long paddr = 0;
+	int i;
+
+	for (i = 0; i < VDMA_PGTBL_ENTRIES; i++) {
+		pgtbl[i].frame = paddr;
+		pgtbl[i].owner = VDMA_PAGE_EMPTY;
+		paddr += VDMA_PAGESIZE;
+	}
+}
+
+/*
+ * Initialize the Jazz R4030 dma controller
+ */
+static int __init vdma_init(void)
+{
+	/*
+	 * Allocate 32k of memory for DMA page tables.	This needs to be page
+	 * aligned and should be uncached to avoid cache flushing after every
+	 * update.
+	 */
+	pgtbl = (VDMA_PGTBL_ENTRY *)__get_free_pages(GFP_KERNEL | GFP_DMA,
+						    get_order(VDMA_PGTBL_SIZE));
+	BUG_ON(!pgtbl);
+	dma_cache_wback_inv((unsigned long)pgtbl, VDMA_PGTBL_SIZE);
+	pgtbl = (VDMA_PGTBL_ENTRY *)CKSEG1ADDR((unsigned long)pgtbl);
+
+	/*
+	 * Clear the R4030 translation table
+	 */
+	vdma_pgtbl_init();
+
+	r4030_write_reg32(JAZZ_R4030_TRSTBL_BASE,
+			  CPHYSADDR((unsigned long)pgtbl));
+	r4030_write_reg32(JAZZ_R4030_TRSTBL_LIM, VDMA_PGTBL_SIZE);
+	r4030_write_reg32(JAZZ_R4030_TRSTBL_INV, 0);
+
+	printk(KERN_INFO "VDMA: R4030 DMA pagetables initialized.\n");
+	return 0;
+}
+arch_initcall(vdma_init);
+
+/*
+ * Allocate DMA pagetables using a simple first-fit algorithm
+ */
+unsigned long vdma_alloc(unsigned long paddr, unsigned long size)
+{
+	int first, last, pages, frame, i;
+	unsigned long laddr, flags;
+
+	/* check arguments */
+
+	if (paddr > 0x1fffffff) {
+		if (vdma_debug)
+			printk("vdma_alloc: Invalid physical address: %08lx\n",
+			       paddr);
+		return DMA_MAPPING_ERROR;	/* invalid physical address */
+	}
+	if (size > 0x400000 || size == 0) {
+		if (vdma_debug)
+			printk("vdma_alloc: Invalid size: %08lx\n", size);
+		return DMA_MAPPING_ERROR;	/* invalid physical address */
+	}
+
+	spin_lock_irqsave(&vdma_lock, flags);
+	/*
+	 * Find free chunk
+	 */
+	pages = VDMA_PAGE(paddr + size) - VDMA_PAGE(paddr) + 1;
+	first = 0;
+	while (1) {
+		while (pgtbl[first].owner != VDMA_PAGE_EMPTY &&
+		       first < VDMA_PGTBL_ENTRIES) first++;
+		if (first + pages > VDMA_PGTBL_ENTRIES) {	/* nothing free */
+			spin_unlock_irqrestore(&vdma_lock, flags);
+			return DMA_MAPPING_ERROR;
+		}
+
+		last = first + 1;
+		while (pgtbl[last].owner == VDMA_PAGE_EMPTY
+		       && last - first < pages)
+			last++;
+
+		if (last - first == pages)
+			break;	/* found */
+		first = last + 1;
+	}
+
+	/*
+	 * Mark pages as allocated
+	 */
+	laddr = (first << 12) + (paddr & (VDMA_PAGESIZE - 1));
+	frame = paddr & ~(VDMA_PAGESIZE - 1);
+
+	for (i = first; i < last; i++) {
+		pgtbl[i].frame = frame;
+		pgtbl[i].owner = laddr;
+		frame += VDMA_PAGESIZE;
+	}
+
+	/*
+	 * Update translation table and return logical start address
+	 */
+	r4030_write_reg32(JAZZ_R4030_TRSTBL_INV, 0);
+
+	if (vdma_debug > 1)
+		printk("vdma_alloc: Allocated %d pages starting from %08lx\n",
+		     pages, laddr);
+
+	if (vdma_debug > 2) {
+		printk("LADDR: ");
+		for (i = first; i < last; i++)
+			printk("%08x ", i << 12);
+		printk("\nPADDR: ");
+		for (i = first; i < last; i++)
+			printk("%08x ", pgtbl[i].frame);
+		printk("\nOWNER: ");
+		for (i = first; i < last; i++)
+			printk("%08x ", pgtbl[i].owner);
+		printk("\n");
+	}
+
+	spin_unlock_irqrestore(&vdma_lock, flags);
+
+	return laddr;
+}
+
+EXPORT_SYMBOL(vdma_alloc);
+
+/*
+ * Free previously allocated dma translation pages
+ * Note that this does NOT change the translation table,
+ * it just marks the free'd pages as unused!
+ */
+int vdma_free(unsigned long laddr)
+{
+	int i;
+
+	i = laddr >> 12;
+
+	if (pgtbl[i].owner != laddr) {
+		printk
+		    ("vdma_free: trying to free other's dma pages, laddr=%8lx\n",
+		     laddr);
+		return -1;
+	}
+
+	while (i < VDMA_PGTBL_ENTRIES && pgtbl[i].owner == laddr) {
+		pgtbl[i].owner = VDMA_PAGE_EMPTY;
+		i++;
+	}
+
+	if (vdma_debug > 1)
+		printk("vdma_free: freed %ld pages starting from %08lx\n",
+		       i - (laddr >> 12), laddr);
+
+	return 0;
+}
+
+EXPORT_SYMBOL(vdma_free);
+
+/*
+ * Translate a physical address to a logical address.
+ * This will return the logical address of the first
+ * match.
+ */
+unsigned long vdma_phys2log(unsigned long paddr)
+{
+	int i;
+	int frame;
+
+	frame = paddr & ~(VDMA_PAGESIZE - 1);
+
+	for (i = 0; i < VDMA_PGTBL_ENTRIES; i++) {
+		if (pgtbl[i].frame == frame)
+			break;
+	}
+
+	if (i == VDMA_PGTBL_ENTRIES)
+		return ~0UL;
+
+	return (i << 12) + (paddr & (VDMA_PAGESIZE - 1));
+}
+
+EXPORT_SYMBOL(vdma_phys2log);
+
+/*
+ * Translate a logical DMA address to a physical address
+ */
+unsigned long vdma_log2phys(unsigned long laddr)
+{
+	return pgtbl[laddr >> 12].frame + (laddr & (VDMA_PAGESIZE - 1));
+}
+
+EXPORT_SYMBOL(vdma_log2phys);
+
+/*
+ * Print DMA statistics
+ */
+void vdma_stats(void)
+{
+	int i;
+
+	printk("vdma_stats: CONFIG: %08x\n",
+	       r4030_read_reg32(JAZZ_R4030_CONFIG));
+	printk("R4030 translation table base: %08x\n",
+	       r4030_read_reg32(JAZZ_R4030_TRSTBL_BASE));
+	printk("R4030 translation table limit: %08x\n",
+	       r4030_read_reg32(JAZZ_R4030_TRSTBL_LIM));
+	printk("vdma_stats: INV_ADDR: %08x\n",
+	       r4030_read_reg32(JAZZ_R4030_INV_ADDR));
+	printk("vdma_stats: R_FAIL_ADDR: %08x\n",
+	       r4030_read_reg32(JAZZ_R4030_R_FAIL_ADDR));
+	printk("vdma_stats: M_FAIL_ADDR: %08x\n",
+	       r4030_read_reg32(JAZZ_R4030_M_FAIL_ADDR));
+	printk("vdma_stats: IRQ_SOURCE: %08x\n",
+	       r4030_read_reg32(JAZZ_R4030_IRQ_SOURCE));
+	printk("vdma_stats: I386_ERROR: %08x\n",
+	       r4030_read_reg32(JAZZ_R4030_I386_ERROR));
+	printk("vdma_chnl_modes:   ");
+	for (i = 0; i < 8; i++)
+		printk("%04x ",
+		       (unsigned) r4030_read_reg32(JAZZ_R4030_CHNL_MODE +
+						   (i << 5)));
+	printk("\n");
+	printk("vdma_chnl_enables: ");
+	for (i = 0; i < 8; i++)
+		printk("%04x ",
+		       (unsigned) r4030_read_reg32(JAZZ_R4030_CHNL_ENABLE +
+						   (i << 5)));
+	printk("\n");
+}
+
+/*
+ * DMA transfer functions
+ */
+
+/*
+ * Enable a DMA channel. Also clear any error conditions.
+ */
+void vdma_enable(int channel)
+{
+	int status;
+
+	if (vdma_debug)
+		printk("vdma_enable: channel %d\n", channel);
+
+	/*
+	 * Check error conditions first
+	 */
+	status = r4030_read_reg32(JAZZ_R4030_CHNL_ENABLE + (channel << 5));
+	if (status & 0x400)
+		printk("VDMA: Channel %d: Address error!\n", channel);
+	if (status & 0x200)
+		printk("VDMA: Channel %d: Memory error!\n", channel);
+
+	/*
+	 * Clear all interrupt flags
+	 */
+	r4030_write_reg32(JAZZ_R4030_CHNL_ENABLE + (channel << 5),
+			  r4030_read_reg32(JAZZ_R4030_CHNL_ENABLE +
+					   (channel << 5)) | R4030_TC_INTR
+			  | R4030_MEM_INTR | R4030_ADDR_INTR);
+
+	/*
+	 * Enable the desired channel
+	 */
+	r4030_write_reg32(JAZZ_R4030_CHNL_ENABLE + (channel << 5),
+			  r4030_read_reg32(JAZZ_R4030_CHNL_ENABLE +
+					   (channel << 5)) |
+			  R4030_CHNL_ENABLE);
+}
+
+EXPORT_SYMBOL(vdma_enable);
+
+/*
+ * Disable a DMA channel
+ */
+void vdma_disable(int channel)
+{
+	if (vdma_debug) {
+		int status =
+		    r4030_read_reg32(JAZZ_R4030_CHNL_ENABLE +
+				     (channel << 5));
+
+		printk("vdma_disable: channel %d\n", channel);
+		printk("VDMA: channel %d status: %04x (%s) mode: "
+		       "%02x addr: %06x count: %06x\n",
+		       channel, status,
+		       ((status & 0x600) ? "ERROR" : "OK"),
+		       (unsigned) r4030_read_reg32(JAZZ_R4030_CHNL_MODE +
+						   (channel << 5)),
+		       (unsigned) r4030_read_reg32(JAZZ_R4030_CHNL_ADDR +
+						   (channel << 5)),
+		       (unsigned) r4030_read_reg32(JAZZ_R4030_CHNL_COUNT +
+						   (channel << 5)));
+	}
+
+	r4030_write_reg32(JAZZ_R4030_CHNL_ENABLE + (channel << 5),
+			  r4030_read_reg32(JAZZ_R4030_CHNL_ENABLE +
+					   (channel << 5)) &
+			  ~R4030_CHNL_ENABLE);
+
+	/*
+	 * After disabling a DMA channel a remote bus register should be
+	 * read to ensure that the current DMA acknowledge cycle is completed.
+	 */
+	*((volatile unsigned int *) JAZZ_DUMMY_DEVICE);
+}
+
+EXPORT_SYMBOL(vdma_disable);
+
+/*
+ * Set DMA mode. This function accepts the mode values used
+ * to set a PC-style DMA controller. For the SCSI and FDC
+ * channels, we also set the default modes each time we're
+ * called.
+ * NOTE: The FAST and BURST dma modes are supported by the
+ * R4030 Rev. 2 and PICA chipsets only. I leave them disabled
+ * for now.
+ */
+void vdma_set_mode(int channel, int mode)
+{
+	if (vdma_debug)
+		printk("vdma_set_mode: channel %d, mode 0x%x\n", channel,
+		       mode);
+
+	switch (channel) {
+	case JAZZ_SCSI_DMA:	/* scsi */
+		r4030_write_reg32(JAZZ_R4030_CHNL_MODE + (channel << 5),
+/*			  R4030_MODE_FAST | */
+/*			  R4030_MODE_BURST | */
+				  R4030_MODE_INTR_EN |
+				  R4030_MODE_WIDTH_16 |
+				  R4030_MODE_ATIME_80);
+		break;
+
+	case JAZZ_FLOPPY_DMA:	/* floppy */
+		r4030_write_reg32(JAZZ_R4030_CHNL_MODE + (channel << 5),
+/*			  R4030_MODE_FAST | */
+/*			  R4030_MODE_BURST | */
+				  R4030_MODE_INTR_EN |
+				  R4030_MODE_WIDTH_8 |
+				  R4030_MODE_ATIME_120);
+		break;
+
+	case JAZZ_AUDIOL_DMA:
+	case JAZZ_AUDIOR_DMA:
+		printk("VDMA: Audio DMA not supported yet.\n");
+		break;
+
+	default:
+		printk
+		    ("VDMA: vdma_set_mode() called with unsupported channel %d!\n",
+		     channel);
+	}
+
+	switch (mode) {
+	case DMA_MODE_READ:
+		r4030_write_reg32(JAZZ_R4030_CHNL_ENABLE + (channel << 5),
+				  r4030_read_reg32(JAZZ_R4030_CHNL_ENABLE +
+						   (channel << 5)) &
+				  ~R4030_CHNL_WRITE);
+		break;
+
+	case DMA_MODE_WRITE:
+		r4030_write_reg32(JAZZ_R4030_CHNL_ENABLE + (channel << 5),
+				  r4030_read_reg32(JAZZ_R4030_CHNL_ENABLE +
+						   (channel << 5)) |
+				  R4030_CHNL_WRITE);
+		break;
+
+	default:
+		printk
+		    ("VDMA: vdma_set_mode() called with unknown dma mode 0x%x\n",
+		     mode);
+	}
+}
+
+EXPORT_SYMBOL(vdma_set_mode);
+
+/*
+ * Set Transfer Address
+ */
+void vdma_set_addr(int channel, long addr)
+{
+	if (vdma_debug)
+		printk("vdma_set_addr: channel %d, addr %lx\n", channel,
+		       addr);
+
+	r4030_write_reg32(JAZZ_R4030_CHNL_ADDR + (channel << 5), addr);
+}
+
+EXPORT_SYMBOL(vdma_set_addr);
+
+/*
+ * Set Transfer Count
+ */
+void vdma_set_count(int channel, int count)
+{
+	if (vdma_debug)
+		printk("vdma_set_count: channel %d, count %08x\n", channel,
+		       (unsigned) count);
+
+	r4030_write_reg32(JAZZ_R4030_CHNL_COUNT + (channel << 5), count);
+}
+
+EXPORT_SYMBOL(vdma_set_count);
+
+/*
+ * Get Residual
+ */
+int vdma_get_residue(int channel)
+{
+	int residual;
+
+	residual = r4030_read_reg32(JAZZ_R4030_CHNL_COUNT + (channel << 5));
+
+	if (vdma_debug)
+		printk("vdma_get_residual: channel %d: residual=%d\n",
+		       channel, residual);
+
+	return residual;
+}
+
+/*
+ * Get DMA channel enable register
+ */
+int vdma_get_enable(int channel)
+{
+	int enable;
+
+	enable = r4030_read_reg32(JAZZ_R4030_CHNL_ENABLE + (channel << 5));
+
+	if (vdma_debug)
+		printk("vdma_get_enable: channel %d: enable=%d\n", channel,
+		       enable);
+
+	return enable;
+}
+
+static void *jazz_dma_alloc(struct device *dev, size_t size,
+		dma_addr_t *dma_handle, gfp_t gfp, unsigned long attrs)
+{
+	struct page *page;
+	void *ret;
+
+	if (attrs & DMA_ATTR_NO_WARN)
+		gfp |= __GFP_NOWARN;
+
+	size = PAGE_ALIGN(size);
+	page = alloc_pages(gfp, get_order(size));
+	if (!page)
+		return NULL;
+	ret = page_address(page);
+	memset(ret, 0, size);
+	*dma_handle = vdma_alloc(virt_to_phys(ret), size);
+	if (*dma_handle == DMA_MAPPING_ERROR)
+		goto out_free_pages;
+	arch_dma_prep_coherent(page, size);
+	return (void *)(UNCAC_BASE + __pa(ret));
+
+out_free_pages:
+	__free_pages(page, get_order(size));
+	return NULL;
+}
+
+static void jazz_dma_free(struct device *dev, size_t size, void *vaddr,
+		dma_addr_t dma_handle, unsigned long attrs)
+{
+	vdma_free(dma_handle);
+	__free_pages(virt_to_page(vaddr), get_order(size));
+}
+
+static dma_addr_t jazz_dma_map_page(struct device *dev, struct page *page,
+		unsigned long offset, size_t size, enum dma_data_direction dir,
+		unsigned long attrs)
+{
+	phys_addr_t phys = page_to_phys(page) + offset;
+
+	if (!(attrs & DMA_ATTR_SKIP_CPU_SYNC))
+		arch_sync_dma_for_device(phys, size, dir);
+	return vdma_alloc(phys, size);
+}
+
+static void jazz_dma_unmap_page(struct device *dev, dma_addr_t dma_addr,
+		size_t size, enum dma_data_direction dir, unsigned long attrs)
+{
+	if (!(attrs & DMA_ATTR_SKIP_CPU_SYNC))
+		arch_sync_dma_for_cpu(vdma_log2phys(dma_addr), size, dir);
+	vdma_free(dma_addr);
+}
+
+static int jazz_dma_map_sg(struct device *dev, struct scatterlist *sglist,
+		int nents, enum dma_data_direction dir, unsigned long attrs)
+{
+	int i;
+	struct scatterlist *sg;
+
+	for_each_sg(sglist, sg, nents, i) {
+		if (!(attrs & DMA_ATTR_SKIP_CPU_SYNC))
+			arch_sync_dma_for_device(sg_phys(sg), sg->length,
+				dir);
+		sg->dma_address = vdma_alloc(sg_phys(sg), sg->length);
+		if (sg->dma_address == DMA_MAPPING_ERROR)
+			return -EIO;
+		sg_dma_len(sg) = sg->length;
+	}
+
+	return nents;
+}
+
+static void jazz_dma_unmap_sg(struct device *dev, struct scatterlist *sglist,
+		int nents, enum dma_data_direction dir, unsigned long attrs)
+{
+	int i;
+	struct scatterlist *sg;
+
+	for_each_sg(sglist, sg, nents, i) {
+		if (!(attrs & DMA_ATTR_SKIP_CPU_SYNC))
+			arch_sync_dma_for_cpu(sg_phys(sg), sg->length, dir);
+		vdma_free(sg->dma_address);
+	}
+}
+
+static void jazz_dma_sync_single_for_device(struct device *dev,
+		dma_addr_t addr, size_t size, enum dma_data_direction dir)
+{
+	arch_sync_dma_for_device(vdma_log2phys(addr), size, dir);
+}
+
+static void jazz_dma_sync_single_for_cpu(struct device *dev,
+		dma_addr_t addr, size_t size, enum dma_data_direction dir)
+{
+	arch_sync_dma_for_cpu(vdma_log2phys(addr), size, dir);
+}
+
+static void jazz_dma_sync_sg_for_device(struct device *dev,
+		struct scatterlist *sgl, int nents, enum dma_data_direction dir)
+{
+	struct scatterlist *sg;
+	int i;
+
+	for_each_sg(sgl, sg, nents, i)
+		arch_sync_dma_for_device(sg_phys(sg), sg->length, dir);
+}
+
+static void jazz_dma_sync_sg_for_cpu(struct device *dev,
+		struct scatterlist *sgl, int nents, enum dma_data_direction dir)
+{
+	struct scatterlist *sg;
+	int i;
+
+	for_each_sg(sgl, sg, nents, i)
+		arch_sync_dma_for_cpu(sg_phys(sg), sg->length, dir);
+}
+
+const struct dma_map_ops jazz_dma_ops = {
+	.alloc			= jazz_dma_alloc,
+	.free			= jazz_dma_free,
+	.map_page		= jazz_dma_map_page,
+	.unmap_page		= jazz_dma_unmap_page,
+	.map_sg			= jazz_dma_map_sg,
+	.unmap_sg		= jazz_dma_unmap_sg,
+	.sync_single_for_cpu	= jazz_dma_sync_single_for_cpu,
+	.sync_single_for_device	= jazz_dma_sync_single_for_device,
+	.sync_sg_for_cpu	= jazz_dma_sync_sg_for_cpu,
+	.sync_sg_for_device	= jazz_dma_sync_sg_for_device,
+	.mmap			= dma_common_mmap,
+	.get_sgtable		= dma_common_get_sgtable,
+	.alloc_pages		= dma_common_alloc_pages,
+	.free_pages		= dma_common_free_pages,
+};
+EXPORT_SYMBOL(jazz_dma_ops);
diff --git a/arch/mips/jazz/reset.c b/arch/mips/jazz/reset.c
new file mode 100644
index 000000000..052b01f5d
--- /dev/null
+++ b/arch/mips/jazz/reset.c
@@ -0,0 +1,57 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Reset a Jazz machine.
+ *
+ * We don't trust the firmware so we do it the classic way by poking and
+ * stabbing at the keyboard controller ...
+ */
+#include <linux/jiffies.h>
+#include <asm/jazz.h>
+
+#define KBD_STAT_IBF		0x02	/* Keyboard input buffer full */
+
+static void jazz_write_output(unsigned char val)
+{
+	int status;
+
+	do {
+		status = jazz_kh->command;
+	} while (status & KBD_STAT_IBF);
+	jazz_kh->data = val;
+}
+
+static void jazz_write_command(unsigned char val)
+{
+	int status;
+
+	do {
+		status = jazz_kh->command;
+	} while (status & KBD_STAT_IBF);
+	jazz_kh->command = val;
+}
+
+static unsigned char jazz_read_status(void)
+{
+	return jazz_kh->command;
+}
+
+static inline void kb_wait(void)
+{
+	unsigned long start = jiffies;
+	unsigned long timeout = start + HZ/2;
+
+	do {
+		if (! (jazz_read_status() & 0x02))
+			return;
+	} while (time_before_eq(jiffies, timeout));
+}
+
+void jazz_machine_restart(char *command)
+{
+	while(1) {
+		kb_wait();
+		jazz_write_command(0xd1);
+		kb_wait();
+		jazz_write_output(0x00);
+	}
+}
diff --git a/arch/mips/jazz/setup.c b/arch/mips/jazz/setup.c
new file mode 100644
index 000000000..04aab419a
--- /dev/null
+++ b/arch/mips/jazz/setup.c
@@ -0,0 +1,212 @@
+/*
+ * Setup pointers to hardware-dependent routines.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1996, 1997, 1998, 2001, 07, 08 by Ralf Baechle
+ * Copyright (C) 2001 MIPS Technologies, Inc.
+ * Copyright (C) 2007 by Thomas Bogendoerfer
+ */
+#include <linux/eisa.h>
+#include <linux/init.h>
+#include <linux/ioport.h>
+#include <linux/console.h>
+#include <linux/screen_info.h>
+#include <linux/platform_device.h>
+#include <linux/serial_8250.h>
+#include <linux/dma-mapping.h>
+#include <linux/pgtable.h>
+
+#include <asm/jazz.h>
+#include <asm/jazzdma.h>
+#include <asm/reboot.h>
+#include <asm/tlbmisc.h>
+
+extern asmlinkage void jazz_handle_int(void);
+
+extern void jazz_machine_restart(char *command);
+
+static struct resource jazz_io_resources[] = {
+	{
+		.start	= 0x00,
+		.end	= 0x1f,
+		.name	= "dma1",
+		.flags	= IORESOURCE_IO | IORESOURCE_BUSY
+	}, {
+		.start	= 0x40,
+		.end	= 0x5f,
+		.name	= "timer",
+		.flags	= IORESOURCE_IO | IORESOURCE_BUSY
+	}, {
+		.start	= 0x80,
+		.end	= 0x8f,
+		.name	= "dma page reg",
+		.flags	= IORESOURCE_IO | IORESOURCE_BUSY
+	}, {
+		.start	= 0xc0,
+		.end	= 0xdf,
+		.name	= "dma2",
+		.flags	= IORESOURCE_IO | IORESOURCE_BUSY
+	}
+};
+
+void __init plat_mem_setup(void)
+{
+	int i;
+
+	/* Map 0xe0000000 -> 0x0:800005C0, 0xe0010000 -> 0x1:30000580 */
+	add_wired_entry(0x02000017, 0x03c00017, 0xe0000000, PM_64K);
+	/* Map 0xe2000000 -> 0x0:900005C0, 0xe3010000 -> 0x0:910005C0 */
+	add_wired_entry(0x02400017, 0x02440017, 0xe2000000, PM_16M);
+	/* Map 0xe4000000 -> 0x0:600005C0, 0xe4100000 -> 400005C0 */
+	add_wired_entry(0x01800017, 0x01000017, 0xe4000000, PM_4M);
+
+	set_io_port_base(JAZZ_PORT_BASE);
+#ifdef CONFIG_EISA
+	EISA_bus = 1;
+#endif
+
+	/* request I/O space for devices used on all i[345]86 PCs */
+	for (i = 0; i < ARRAY_SIZE(jazz_io_resources); i++)
+		request_resource(&ioport_resource, jazz_io_resources + i);
+
+	/* The RTC is outside the port address space */
+
+	_machine_restart = jazz_machine_restart;
+
+#ifdef CONFIG_VT
+	screen_info = (struct screen_info) {
+		.orig_video_cols	= 160,
+		.orig_video_lines	= 64,
+		.orig_video_points	= 16,
+	};
+#endif
+
+	add_preferred_console("ttyS", 0, "9600");
+}
+
+#ifdef CONFIG_OLIVETTI_M700
+#define UART_CLK  1843200
+#else
+/* Some Jazz machines seem to have an 8MHz crystal clock but I don't know
+   exactly which ones ... XXX */
+#define UART_CLK (8000000 / 16) /* ( 3072000 / 16) */
+#endif
+
+#define MEMPORT(_base, _irq)				\
+	{						\
+		.mapbase	= (_base),		\
+		.membase	= (void *)(_base),	\
+		.irq		= (_irq),		\
+		.uartclk	= UART_CLK,		\
+		.iotype		= UPIO_MEM,		\
+		.flags		= UPF_BOOT_AUTOCONF,	\
+	}
+
+static struct plat_serial8250_port jazz_serial_data[] = {
+	MEMPORT(JAZZ_SERIAL1_BASE, JAZZ_SERIAL1_IRQ),
+	MEMPORT(JAZZ_SERIAL2_BASE, JAZZ_SERIAL2_IRQ),
+	{ },
+};
+
+static struct platform_device jazz_serial8250_device = {
+	.name			= "serial8250",
+	.id			= PLAT8250_DEV_PLATFORM,
+	.dev			= {
+		.platform_data	= jazz_serial_data,
+	},
+};
+
+static struct resource jazz_esp_rsrc[] = {
+	{
+		.start = JAZZ_SCSI_BASE,
+		.end   = JAZZ_SCSI_BASE + 31,
+		.flags = IORESOURCE_MEM
+	},
+	{
+		.start = JAZZ_SCSI_DMA,
+		.end   = JAZZ_SCSI_DMA,
+		.flags = IORESOURCE_MEM
+	},
+	{
+		.start = JAZZ_SCSI_IRQ,
+		.end   = JAZZ_SCSI_IRQ,
+		.flags = IORESOURCE_IRQ
+	}
+};
+
+static u64 jazz_esp_dma_mask = DMA_BIT_MASK(32);
+
+static struct platform_device jazz_esp_pdev = {
+	.name		= "jazz_esp",
+	.num_resources	= ARRAY_SIZE(jazz_esp_rsrc),
+	.resource	= jazz_esp_rsrc,
+	.dev = {
+		.dma_mask	   = &jazz_esp_dma_mask,
+		.coherent_dma_mask = DMA_BIT_MASK(32),
+	}
+};
+
+static struct resource jazz_sonic_rsrc[] = {
+	{
+		.start = JAZZ_ETHERNET_BASE,
+		.end   = JAZZ_ETHERNET_BASE + 0xff,
+		.flags = IORESOURCE_MEM
+	},
+	{
+		.start = JAZZ_ETHERNET_IRQ,
+		.end   = JAZZ_ETHERNET_IRQ,
+		.flags = IORESOURCE_IRQ
+	}
+};
+
+static u64 jazz_sonic_dma_mask = DMA_BIT_MASK(32);
+
+static struct platform_device jazz_sonic_pdev = {
+	.name		= "jazzsonic",
+	.num_resources	= ARRAY_SIZE(jazz_sonic_rsrc),
+	.resource	= jazz_sonic_rsrc,
+	.dev = {
+		.dma_mask	   = &jazz_sonic_dma_mask,
+		.coherent_dma_mask = DMA_BIT_MASK(32),
+	}
+};
+
+static struct resource jazz_cmos_rsrc[] = {
+	{
+		.start = 0x70,
+		.end   = 0x71,
+		.flags = IORESOURCE_IO
+	},
+	{
+		.start = 8,
+		.end   = 8,
+		.flags = IORESOURCE_IRQ
+	}
+};
+
+static struct platform_device jazz_cmos_pdev = {
+	.name		= "rtc_cmos",
+	.num_resources	= ARRAY_SIZE(jazz_cmos_rsrc),
+	.resource	= jazz_cmos_rsrc
+};
+
+static struct platform_device pcspeaker_pdev = {
+	.name		= "pcspkr",
+	.id		= -1,
+};
+
+static int __init jazz_setup_devinit(void)
+{
+	platform_device_register(&jazz_serial8250_device);
+	platform_device_register(&jazz_esp_pdev);
+	platform_device_register(&jazz_sonic_pdev);
+	platform_device_register(&jazz_cmos_pdev);
+	platform_device_register(&pcspeaker_pdev);
+
+	return 0;
+}
+
+device_initcall(jazz_setup_devinit);
diff --git a/arch/mips/kernel/.gitignore b/arch/mips/kernel/.gitignore
new file mode 100644
index 000000000..bbb90f92d
--- /dev/null
+++ b/arch/mips/kernel/.gitignore
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0-only
+vmlinux.lds
diff --git a/arch/mips/kernel/Makefile b/arch/mips/kernel/Makefile
new file mode 100644
index 000000000..5d1addac5
--- /dev/null
+++ b/arch/mips/kernel/Makefile
@@ -0,0 +1,117 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Makefile for the Linux/MIPS kernel.
+#
+
+extra-y		:= vmlinux.lds
+
+obj-y		+= head.o branch.o cmpxchg.o elf.o entry.o genex.o idle.o irq.o \
+		   process.o prom.o ptrace.o reset.o setup.o signal.o \
+		   syscall.o time.o topology.o traps.o unaligned.o watch.o \
+		   vdso.o cacheinfo.o
+
+ifdef CONFIG_CPU_R3K_TLB
+obj-y		+= cpu-r3k-probe.o
+else
+obj-y		+= cpu-probe.o
+endif
+
+ifdef CONFIG_FUNCTION_TRACER
+CFLAGS_REMOVE_ftrace.o = $(CC_FLAGS_FTRACE)
+CFLAGS_REMOVE_early_printk.o =  $(CC_FLAGS_FTRACE)
+CFLAGS_REMOVE_perf_event.o = $(CC_FLAGS_FTRACE)
+CFLAGS_REMOVE_perf_event_mipsxx.o = $(CC_FLAGS_FTRACE)
+endif
+
+obj-$(CONFIG_CEVT_BCM1480)	+= cevt-bcm1480.o
+obj-$(CONFIG_CEVT_R4K)		+= cevt-r4k.o
+obj-$(CONFIG_CEVT_DS1287)	+= cevt-ds1287.o
+obj-$(CONFIG_CEVT_GT641XX)	+= cevt-gt641xx.o
+obj-$(CONFIG_CEVT_SB1250)	+= cevt-sb1250.o
+obj-$(CONFIG_CEVT_TXX9)		+= cevt-txx9.o
+obj-$(CONFIG_CSRC_BCM1480)	+= csrc-bcm1480.o
+obj-$(CONFIG_CSRC_IOASIC)	+= csrc-ioasic.o
+obj-$(CONFIG_CSRC_R4K)		+= csrc-r4k.o
+obj-$(CONFIG_CSRC_SB1250)	+= csrc-sb1250.o
+obj-$(CONFIG_SYNC_R4K)		+= sync-r4k.o
+
+obj-$(CONFIG_DEBUG_FS)		+= segment.o
+obj-$(CONFIG_STACKTRACE)	+= stacktrace.o
+obj-$(CONFIG_MODULES)		+= module.o
+
+obj-$(CONFIG_FTRACE_SYSCALLS)	+= ftrace.o
+obj-$(CONFIG_FUNCTION_TRACER)	+= mcount.o ftrace.o
+
+sw-y				:= r4k_switch.o
+sw-$(CONFIG_CPU_R3000)		:= r2300_switch.o
+sw-$(CONFIG_CPU_CAVIUM_OCTEON)	:= octeon_switch.o
+obj-y				+= $(sw-y)
+
+obj-$(CONFIG_MIPS_FP_SUPPORT)	+= fpu-probe.o
+obj-$(CONFIG_CPU_R2300_FPU)	+= r2300_fpu.o
+obj-$(CONFIG_CPU_R4K_FPU)	+= r4k_fpu.o
+
+obj-$(CONFIG_SMP)		+= smp.o
+obj-$(CONFIG_SMP_UP)		+= smp-up.o
+obj-$(CONFIG_CPU_BMIPS)		+= smp-bmips.o bmips_vec.o bmips_5xxx_init.o
+
+obj-$(CONFIG_MIPS_MT)		+= mips-mt.o
+obj-$(CONFIG_MIPS_MT_FPAFF)	+= mips-mt-fpaff.o
+obj-$(CONFIG_MIPS_MT_SMP)	+= smp-mt.o
+obj-$(CONFIG_MIPS_CMP)		+= smp-cmp.o
+obj-$(CONFIG_MIPS_CPS)		+= smp-cps.o cps-vec.o
+obj-$(CONFIG_MIPS_CPS_NS16550)	+= cps-vec-ns16550.o
+obj-$(CONFIG_MIPS_SPRAM)	+= spram.o
+
+obj-$(CONFIG_MIPS_VPE_LOADER)	+= vpe.o
+obj-$(CONFIG_MIPS_VPE_LOADER_CMP) += vpe-cmp.o
+obj-$(CONFIG_MIPS_VPE_LOADER_MT) += vpe-mt.o
+obj-$(CONFIG_MIPS_VPE_APSP_API) += rtlx.o
+obj-$(CONFIG_MIPS_VPE_APSP_API_CMP) += rtlx-cmp.o
+obj-$(CONFIG_MIPS_VPE_APSP_API_MT) += rtlx-mt.o
+
+obj-$(CONFIG_MIPS_MSC)		+= irq-msc01.o
+obj-$(CONFIG_IRQ_TXX9)		+= irq_txx9.o
+obj-$(CONFIG_IRQ_GT641XX)	+= irq-gt641xx.o
+
+obj-$(CONFIG_KPROBES)		+= kprobes.o
+obj-$(CONFIG_32BIT)		+= scall32-o32.o
+obj-$(CONFIG_64BIT)		+= scall64-n64.o
+obj-$(CONFIG_MIPS32_COMPAT)	+= linux32.o ptrace32.o signal32.o
+obj-$(CONFIG_MIPS32_N32)	+= scall64-n32.o signal_n32.o
+obj-$(CONFIG_MIPS32_O32)	+= scall64-o32.o signal_o32.o
+
+obj-$(CONFIG_KGDB)		+= kgdb.o
+obj-$(CONFIG_PROC_FS)		+= proc.o
+obj-$(CONFIG_MAGIC_SYSRQ)	+= sysrq.o
+
+obj-$(CONFIG_CPU_R4X00_BUGS64)	+= r4k-bugs64.o
+
+obj-$(CONFIG_I8253)		+= i8253.o
+
+obj-$(CONFIG_GPIO_TXX9)		+= gpio_txx9.o
+
+obj-$(CONFIG_RELOCATABLE)	+= relocate.o
+
+obj-$(CONFIG_KEXEC)		+= machine_kexec.o relocate_kernel.o crash.o
+obj-$(CONFIG_CRASH_DUMP)	+= crash_dump.o
+obj-$(CONFIG_EARLY_PRINTK)	+= early_printk.o
+obj-$(CONFIG_EARLY_PRINTK_8250)	+= early_printk_8250.o
+obj-$(CONFIG_SPINLOCK_TEST)	+= spinlock_test.o
+obj-$(CONFIG_MIPSR2_TO_R6_EMULATOR)	+= mips-r2-to-r6-emul.o
+
+CFLAGS_cpu-bugs64.o	= $(shell if $(CC) $(KBUILD_CFLAGS) -Wa,-mdaddi -c -o /dev/null -x c /dev/null >/dev/null 2>&1; then echo "-DHAVE_AS_SET_DADDI"; fi)
+
+obj-$(CONFIG_PERF_EVENTS)	+= perf_event.o perf_regs.o
+obj-$(CONFIG_HW_PERF_EVENTS)	+= perf_event_mipsxx.o
+
+obj-$(CONFIG_JUMP_LABEL)	+= jump_label.o
+obj-$(CONFIG_UPROBES)		+= uprobes.o
+
+obj-$(CONFIG_MIPS_CM)		+= mips-cm.o
+obj-$(CONFIG_MIPS_CPC)		+= mips-cpc.o
+
+obj-$(CONFIG_CPU_PM)		+= pm.o
+obj-$(CONFIG_MIPS_CPS_PM)	+= pm-cps.o
+
+CPPFLAGS_vmlinux.lds		:= $(KBUILD_CFLAGS)
diff --git a/arch/mips/kernel/access-helper.h b/arch/mips/kernel/access-helper.h
new file mode 100644
index 000000000..590388031
--- /dev/null
+++ b/arch/mips/kernel/access-helper.h
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#include <linux/uaccess.h>
+
+static inline int __get_addr(unsigned long *a, unsigned long *p, bool user)
+{
+	return user ? get_user(*a, (unsigned long __user *)p) :
+		      get_kernel_nofault(*a, p);
+}
+
+static inline int __get_inst16(u16 *i, u16 *p, bool user)
+{
+	return user ? get_user(*i, (u16 __user *)p) : get_kernel_nofault(*i, p);
+}
+
+static inline int __get_inst32(u32 *i, u32 *p, bool user)
+{
+	return user ? get_user(*i, (u32 __user *)p) : get_kernel_nofault(*i, p);
+}
diff --git a/arch/mips/kernel/asm-offsets.c b/arch/mips/kernel/asm-offsets.c
new file mode 100644
index 000000000..c4501897b
--- /dev/null
+++ b/arch/mips/kernel/asm-offsets.c
@@ -0,0 +1,398 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * asm-offsets.c: Calculate pt_regs and task_struct offsets.
+ *
+ * Copyright (C) 1996 David S. Miller
+ * Copyright (C) 1997, 1998, 1999, 2000, 2001, 2002, 2003 Ralf Baechle
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ *
+ * Kevin Kissell, kevink@mips.com and Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 2000 MIPS Technologies, Inc.
+ */
+#include <linux/compat.h>
+#include <linux/types.h>
+#include <linux/sched.h>
+#include <linux/mm.h>
+#include <linux/kbuild.h>
+#include <linux/suspend.h>
+#include <asm/cpu-info.h>
+#include <asm/pm.h>
+#include <asm/ptrace.h>
+#include <asm/processor.h>
+#include <asm/smp-cps.h>
+
+#include <linux/kvm_host.h>
+
+void output_ptreg_defines(void)
+{
+	COMMENT("MIPS pt_regs offsets.");
+	OFFSET(PT_R0, pt_regs, regs[0]);
+	OFFSET(PT_R1, pt_regs, regs[1]);
+	OFFSET(PT_R2, pt_regs, regs[2]);
+	OFFSET(PT_R3, pt_regs, regs[3]);
+	OFFSET(PT_R4, pt_regs, regs[4]);
+	OFFSET(PT_R5, pt_regs, regs[5]);
+	OFFSET(PT_R6, pt_regs, regs[6]);
+	OFFSET(PT_R7, pt_regs, regs[7]);
+	OFFSET(PT_R8, pt_regs, regs[8]);
+	OFFSET(PT_R9, pt_regs, regs[9]);
+	OFFSET(PT_R10, pt_regs, regs[10]);
+	OFFSET(PT_R11, pt_regs, regs[11]);
+	OFFSET(PT_R12, pt_regs, regs[12]);
+	OFFSET(PT_R13, pt_regs, regs[13]);
+	OFFSET(PT_R14, pt_regs, regs[14]);
+	OFFSET(PT_R15, pt_regs, regs[15]);
+	OFFSET(PT_R16, pt_regs, regs[16]);
+	OFFSET(PT_R17, pt_regs, regs[17]);
+	OFFSET(PT_R18, pt_regs, regs[18]);
+	OFFSET(PT_R19, pt_regs, regs[19]);
+	OFFSET(PT_R20, pt_regs, regs[20]);
+	OFFSET(PT_R21, pt_regs, regs[21]);
+	OFFSET(PT_R22, pt_regs, regs[22]);
+	OFFSET(PT_R23, pt_regs, regs[23]);
+	OFFSET(PT_R24, pt_regs, regs[24]);
+	OFFSET(PT_R25, pt_regs, regs[25]);
+	OFFSET(PT_R26, pt_regs, regs[26]);
+	OFFSET(PT_R27, pt_regs, regs[27]);
+	OFFSET(PT_R28, pt_regs, regs[28]);
+	OFFSET(PT_R29, pt_regs, regs[29]);
+	OFFSET(PT_R30, pt_regs, regs[30]);
+	OFFSET(PT_R31, pt_regs, regs[31]);
+	OFFSET(PT_LO, pt_regs, lo);
+	OFFSET(PT_HI, pt_regs, hi);
+#ifdef CONFIG_CPU_HAS_SMARTMIPS
+	OFFSET(PT_ACX, pt_regs, acx);
+#endif
+	OFFSET(PT_EPC, pt_regs, cp0_epc);
+	OFFSET(PT_BVADDR, pt_regs, cp0_badvaddr);
+	OFFSET(PT_STATUS, pt_regs, cp0_status);
+	OFFSET(PT_CAUSE, pt_regs, cp0_cause);
+#ifdef CONFIG_CPU_CAVIUM_OCTEON
+	OFFSET(PT_MPL, pt_regs, mpl);
+	OFFSET(PT_MTP, pt_regs, mtp);
+#endif /* CONFIG_CPU_CAVIUM_OCTEON */
+	DEFINE(PT_SIZE, sizeof(struct pt_regs));
+	BLANK();
+}
+
+void output_task_defines(void)
+{
+	COMMENT("MIPS task_struct offsets.");
+	OFFSET(TASK_THREAD_INFO, task_struct, stack);
+	OFFSET(TASK_FLAGS, task_struct, flags);
+	OFFSET(TASK_MM, task_struct, mm);
+	OFFSET(TASK_PID, task_struct, pid);
+#if defined(CONFIG_STACKPROTECTOR)
+	OFFSET(TASK_STACK_CANARY, task_struct, stack_canary);
+#endif
+	DEFINE(TASK_STRUCT_SIZE, sizeof(struct task_struct));
+	BLANK();
+}
+
+void output_thread_info_defines(void)
+{
+	COMMENT("MIPS thread_info offsets.");
+	OFFSET(TI_TASK, thread_info, task);
+	OFFSET(TI_FLAGS, thread_info, flags);
+	OFFSET(TI_TP_VALUE, thread_info, tp_value);
+	OFFSET(TI_CPU, thread_info, cpu);
+	OFFSET(TI_PRE_COUNT, thread_info, preempt_count);
+	OFFSET(TI_REGS, thread_info, regs);
+	DEFINE(_THREAD_SIZE, THREAD_SIZE);
+	DEFINE(_THREAD_MASK, THREAD_MASK);
+	DEFINE(_IRQ_STACK_SIZE, IRQ_STACK_SIZE);
+	DEFINE(_IRQ_STACK_START, IRQ_STACK_START);
+	BLANK();
+}
+
+void output_thread_defines(void)
+{
+	COMMENT("MIPS specific thread_struct offsets.");
+	OFFSET(THREAD_REG16, task_struct, thread.reg16);
+	OFFSET(THREAD_REG17, task_struct, thread.reg17);
+	OFFSET(THREAD_REG18, task_struct, thread.reg18);
+	OFFSET(THREAD_REG19, task_struct, thread.reg19);
+	OFFSET(THREAD_REG20, task_struct, thread.reg20);
+	OFFSET(THREAD_REG21, task_struct, thread.reg21);
+	OFFSET(THREAD_REG22, task_struct, thread.reg22);
+	OFFSET(THREAD_REG23, task_struct, thread.reg23);
+	OFFSET(THREAD_REG29, task_struct, thread.reg29);
+	OFFSET(THREAD_REG30, task_struct, thread.reg30);
+	OFFSET(THREAD_REG31, task_struct, thread.reg31);
+	OFFSET(THREAD_STATUS, task_struct,
+	       thread.cp0_status);
+
+	OFFSET(THREAD_BVADDR, task_struct, \
+	       thread.cp0_badvaddr);
+	OFFSET(THREAD_BUADDR, task_struct, \
+	       thread.cp0_baduaddr);
+	OFFSET(THREAD_ECODE, task_struct, \
+	       thread.error_code);
+	OFFSET(THREAD_TRAPNO, task_struct, thread.trap_nr);
+	BLANK();
+}
+
+#ifdef CONFIG_MIPS_FP_SUPPORT
+void output_thread_fpu_defines(void)
+{
+	OFFSET(THREAD_FPU, task_struct, thread.fpu);
+
+	OFFSET(THREAD_FPR0, task_struct, thread.fpu.fpr[0]);
+	OFFSET(THREAD_FPR1, task_struct, thread.fpu.fpr[1]);
+	OFFSET(THREAD_FPR2, task_struct, thread.fpu.fpr[2]);
+	OFFSET(THREAD_FPR3, task_struct, thread.fpu.fpr[3]);
+	OFFSET(THREAD_FPR4, task_struct, thread.fpu.fpr[4]);
+	OFFSET(THREAD_FPR5, task_struct, thread.fpu.fpr[5]);
+	OFFSET(THREAD_FPR6, task_struct, thread.fpu.fpr[6]);
+	OFFSET(THREAD_FPR7, task_struct, thread.fpu.fpr[7]);
+	OFFSET(THREAD_FPR8, task_struct, thread.fpu.fpr[8]);
+	OFFSET(THREAD_FPR9, task_struct, thread.fpu.fpr[9]);
+	OFFSET(THREAD_FPR10, task_struct, thread.fpu.fpr[10]);
+	OFFSET(THREAD_FPR11, task_struct, thread.fpu.fpr[11]);
+	OFFSET(THREAD_FPR12, task_struct, thread.fpu.fpr[12]);
+	OFFSET(THREAD_FPR13, task_struct, thread.fpu.fpr[13]);
+	OFFSET(THREAD_FPR14, task_struct, thread.fpu.fpr[14]);
+	OFFSET(THREAD_FPR15, task_struct, thread.fpu.fpr[15]);
+	OFFSET(THREAD_FPR16, task_struct, thread.fpu.fpr[16]);
+	OFFSET(THREAD_FPR17, task_struct, thread.fpu.fpr[17]);
+	OFFSET(THREAD_FPR18, task_struct, thread.fpu.fpr[18]);
+	OFFSET(THREAD_FPR19, task_struct, thread.fpu.fpr[19]);
+	OFFSET(THREAD_FPR20, task_struct, thread.fpu.fpr[20]);
+	OFFSET(THREAD_FPR21, task_struct, thread.fpu.fpr[21]);
+	OFFSET(THREAD_FPR22, task_struct, thread.fpu.fpr[22]);
+	OFFSET(THREAD_FPR23, task_struct, thread.fpu.fpr[23]);
+	OFFSET(THREAD_FPR24, task_struct, thread.fpu.fpr[24]);
+	OFFSET(THREAD_FPR25, task_struct, thread.fpu.fpr[25]);
+	OFFSET(THREAD_FPR26, task_struct, thread.fpu.fpr[26]);
+	OFFSET(THREAD_FPR27, task_struct, thread.fpu.fpr[27]);
+	OFFSET(THREAD_FPR28, task_struct, thread.fpu.fpr[28]);
+	OFFSET(THREAD_FPR29, task_struct, thread.fpu.fpr[29]);
+	OFFSET(THREAD_FPR30, task_struct, thread.fpu.fpr[30]);
+	OFFSET(THREAD_FPR31, task_struct, thread.fpu.fpr[31]);
+
+	OFFSET(THREAD_FCR31, task_struct, thread.fpu.fcr31);
+	OFFSET(THREAD_MSA_CSR, task_struct, thread.fpu.msacsr);
+	BLANK();
+}
+#endif
+
+void output_mm_defines(void)
+{
+	COMMENT("Size of struct page");
+	DEFINE(STRUCT_PAGE_SIZE, sizeof(struct page));
+	BLANK();
+	COMMENT("Linux mm_struct offsets.");
+	OFFSET(MM_USERS, mm_struct, mm_users);
+	OFFSET(MM_PGD, mm_struct, pgd);
+	OFFSET(MM_CONTEXT, mm_struct, context);
+	BLANK();
+	DEFINE(_PGD_T_SIZE, sizeof(pgd_t));
+	DEFINE(_PMD_T_SIZE, sizeof(pmd_t));
+	DEFINE(_PTE_T_SIZE, sizeof(pte_t));
+	BLANK();
+	DEFINE(_PGD_T_LOG2, PGD_T_LOG2);
+#ifndef __PAGETABLE_PMD_FOLDED
+	DEFINE(_PMD_T_LOG2, PMD_T_LOG2);
+#endif
+	DEFINE(_PTE_T_LOG2, PTE_T_LOG2);
+	BLANK();
+	BLANK();
+	DEFINE(_PMD_SHIFT, PMD_SHIFT);
+	DEFINE(_PGDIR_SHIFT, PGDIR_SHIFT);
+	BLANK();
+	DEFINE(_PTRS_PER_PGD, PTRS_PER_PGD);
+	DEFINE(_PTRS_PER_PMD, PTRS_PER_PMD);
+	DEFINE(_PTRS_PER_PTE, PTRS_PER_PTE);
+	BLANK();
+	DEFINE(_PAGE_SHIFT, PAGE_SHIFT);
+	DEFINE(_PAGE_SIZE, PAGE_SIZE);
+	BLANK();
+}
+
+#ifdef CONFIG_32BIT
+void output_sc_defines(void)
+{
+	COMMENT("Linux sigcontext offsets.");
+	OFFSET(SC_REGS, sigcontext, sc_regs);
+	OFFSET(SC_FPREGS, sigcontext, sc_fpregs);
+	OFFSET(SC_ACX, sigcontext, sc_acx);
+	OFFSET(SC_MDHI, sigcontext, sc_mdhi);
+	OFFSET(SC_MDLO, sigcontext, sc_mdlo);
+	OFFSET(SC_PC, sigcontext, sc_pc);
+	OFFSET(SC_FPC_CSR, sigcontext, sc_fpc_csr);
+	OFFSET(SC_FPC_EIR, sigcontext, sc_fpc_eir);
+	OFFSET(SC_HI1, sigcontext, sc_hi1);
+	OFFSET(SC_LO1, sigcontext, sc_lo1);
+	OFFSET(SC_HI2, sigcontext, sc_hi2);
+	OFFSET(SC_LO2, sigcontext, sc_lo2);
+	OFFSET(SC_HI3, sigcontext, sc_hi3);
+	OFFSET(SC_LO3, sigcontext, sc_lo3);
+	BLANK();
+}
+#endif
+
+#ifdef CONFIG_64BIT
+void output_sc_defines(void)
+{
+	COMMENT("Linux sigcontext offsets.");
+	OFFSET(SC_REGS, sigcontext, sc_regs);
+	OFFSET(SC_FPREGS, sigcontext, sc_fpregs);
+	OFFSET(SC_MDHI, sigcontext, sc_mdhi);
+	OFFSET(SC_MDLO, sigcontext, sc_mdlo);
+	OFFSET(SC_PC, sigcontext, sc_pc);
+	OFFSET(SC_FPC_CSR, sigcontext, sc_fpc_csr);
+	BLANK();
+}
+#endif
+
+void output_signal_defined(void)
+{
+	COMMENT("Linux signal numbers.");
+	DEFINE(_SIGHUP, SIGHUP);
+	DEFINE(_SIGINT, SIGINT);
+	DEFINE(_SIGQUIT, SIGQUIT);
+	DEFINE(_SIGILL, SIGILL);
+	DEFINE(_SIGTRAP, SIGTRAP);
+	DEFINE(_SIGIOT, SIGIOT);
+	DEFINE(_SIGABRT, SIGABRT);
+	DEFINE(_SIGEMT, SIGEMT);
+	DEFINE(_SIGFPE, SIGFPE);
+	DEFINE(_SIGKILL, SIGKILL);
+	DEFINE(_SIGBUS, SIGBUS);
+	DEFINE(_SIGSEGV, SIGSEGV);
+	DEFINE(_SIGSYS, SIGSYS);
+	DEFINE(_SIGPIPE, SIGPIPE);
+	DEFINE(_SIGALRM, SIGALRM);
+	DEFINE(_SIGTERM, SIGTERM);
+	DEFINE(_SIGUSR1, SIGUSR1);
+	DEFINE(_SIGUSR2, SIGUSR2);
+	DEFINE(_SIGCHLD, SIGCHLD);
+	DEFINE(_SIGPWR, SIGPWR);
+	DEFINE(_SIGWINCH, SIGWINCH);
+	DEFINE(_SIGURG, SIGURG);
+	DEFINE(_SIGIO, SIGIO);
+	DEFINE(_SIGSTOP, SIGSTOP);
+	DEFINE(_SIGTSTP, SIGTSTP);
+	DEFINE(_SIGCONT, SIGCONT);
+	DEFINE(_SIGTTIN, SIGTTIN);
+	DEFINE(_SIGTTOU, SIGTTOU);
+	DEFINE(_SIGVTALRM, SIGVTALRM);
+	DEFINE(_SIGPROF, SIGPROF);
+	DEFINE(_SIGXCPU, SIGXCPU);
+	DEFINE(_SIGXFSZ, SIGXFSZ);
+	BLANK();
+}
+
+#ifdef CONFIG_CPU_CAVIUM_OCTEON
+void output_octeon_cop2_state_defines(void)
+{
+	COMMENT("Octeon specific octeon_cop2_state offsets.");
+	OFFSET(OCTEON_CP2_CRC_IV,	octeon_cop2_state, cop2_crc_iv);
+	OFFSET(OCTEON_CP2_CRC_LENGTH,	octeon_cop2_state, cop2_crc_length);
+	OFFSET(OCTEON_CP2_CRC_POLY,	octeon_cop2_state, cop2_crc_poly);
+	OFFSET(OCTEON_CP2_LLM_DAT,	octeon_cop2_state, cop2_llm_dat);
+	OFFSET(OCTEON_CP2_3DES_IV,	octeon_cop2_state, cop2_3des_iv);
+	OFFSET(OCTEON_CP2_3DES_KEY,	octeon_cop2_state, cop2_3des_key);
+	OFFSET(OCTEON_CP2_3DES_RESULT,	octeon_cop2_state, cop2_3des_result);
+	OFFSET(OCTEON_CP2_AES_INP0,	octeon_cop2_state, cop2_aes_inp0);
+	OFFSET(OCTEON_CP2_AES_IV,	octeon_cop2_state, cop2_aes_iv);
+	OFFSET(OCTEON_CP2_AES_KEY,	octeon_cop2_state, cop2_aes_key);
+	OFFSET(OCTEON_CP2_AES_KEYLEN,	octeon_cop2_state, cop2_aes_keylen);
+	OFFSET(OCTEON_CP2_AES_RESULT,	octeon_cop2_state, cop2_aes_result);
+	OFFSET(OCTEON_CP2_GFM_MULT,	octeon_cop2_state, cop2_gfm_mult);
+	OFFSET(OCTEON_CP2_GFM_POLY,	octeon_cop2_state, cop2_gfm_poly);
+	OFFSET(OCTEON_CP2_GFM_RESULT,	octeon_cop2_state, cop2_gfm_result);
+	OFFSET(OCTEON_CP2_HSH_DATW,	octeon_cop2_state, cop2_hsh_datw);
+	OFFSET(OCTEON_CP2_HSH_IVW,	octeon_cop2_state, cop2_hsh_ivw);
+	OFFSET(OCTEON_CP2_SHA3,		octeon_cop2_state, cop2_sha3);
+	OFFSET(THREAD_CP2,	task_struct, thread.cp2);
+	OFFSET(THREAD_CVMSEG,	task_struct, thread.cvmseg.cvmseg);
+	BLANK();
+}
+#endif
+
+#ifdef CONFIG_HIBERNATION
+void output_pbe_defines(void)
+{
+	COMMENT(" Linux struct pbe offsets. ");
+	OFFSET(PBE_ADDRESS, pbe, address);
+	OFFSET(PBE_ORIG_ADDRESS, pbe, orig_address);
+	OFFSET(PBE_NEXT, pbe, next);
+	DEFINE(PBE_SIZE, sizeof(struct pbe));
+	BLANK();
+}
+#endif
+
+#ifdef CONFIG_CPU_PM
+void output_pm_defines(void)
+{
+	COMMENT(" PM offsets. ");
+#ifdef CONFIG_EVA
+	OFFSET(SSS_SEGCTL0,	mips_static_suspend_state, segctl[0]);
+	OFFSET(SSS_SEGCTL1,	mips_static_suspend_state, segctl[1]);
+	OFFSET(SSS_SEGCTL2,	mips_static_suspend_state, segctl[2]);
+#endif
+	OFFSET(SSS_SP,		mips_static_suspend_state, sp);
+	BLANK();
+}
+#endif
+
+#ifdef CONFIG_MIPS_FP_SUPPORT
+void output_kvm_defines(void)
+{
+	COMMENT(" KVM/MIPS Specific offsets. ");
+
+	OFFSET(VCPU_FPR0, kvm_vcpu_arch, fpu.fpr[0]);
+	OFFSET(VCPU_FPR1, kvm_vcpu_arch, fpu.fpr[1]);
+	OFFSET(VCPU_FPR2, kvm_vcpu_arch, fpu.fpr[2]);
+	OFFSET(VCPU_FPR3, kvm_vcpu_arch, fpu.fpr[3]);
+	OFFSET(VCPU_FPR4, kvm_vcpu_arch, fpu.fpr[4]);
+	OFFSET(VCPU_FPR5, kvm_vcpu_arch, fpu.fpr[5]);
+	OFFSET(VCPU_FPR6, kvm_vcpu_arch, fpu.fpr[6]);
+	OFFSET(VCPU_FPR7, kvm_vcpu_arch, fpu.fpr[7]);
+	OFFSET(VCPU_FPR8, kvm_vcpu_arch, fpu.fpr[8]);
+	OFFSET(VCPU_FPR9, kvm_vcpu_arch, fpu.fpr[9]);
+	OFFSET(VCPU_FPR10, kvm_vcpu_arch, fpu.fpr[10]);
+	OFFSET(VCPU_FPR11, kvm_vcpu_arch, fpu.fpr[11]);
+	OFFSET(VCPU_FPR12, kvm_vcpu_arch, fpu.fpr[12]);
+	OFFSET(VCPU_FPR13, kvm_vcpu_arch, fpu.fpr[13]);
+	OFFSET(VCPU_FPR14, kvm_vcpu_arch, fpu.fpr[14]);
+	OFFSET(VCPU_FPR15, kvm_vcpu_arch, fpu.fpr[15]);
+	OFFSET(VCPU_FPR16, kvm_vcpu_arch, fpu.fpr[16]);
+	OFFSET(VCPU_FPR17, kvm_vcpu_arch, fpu.fpr[17]);
+	OFFSET(VCPU_FPR18, kvm_vcpu_arch, fpu.fpr[18]);
+	OFFSET(VCPU_FPR19, kvm_vcpu_arch, fpu.fpr[19]);
+	OFFSET(VCPU_FPR20, kvm_vcpu_arch, fpu.fpr[20]);
+	OFFSET(VCPU_FPR21, kvm_vcpu_arch, fpu.fpr[21]);
+	OFFSET(VCPU_FPR22, kvm_vcpu_arch, fpu.fpr[22]);
+	OFFSET(VCPU_FPR23, kvm_vcpu_arch, fpu.fpr[23]);
+	OFFSET(VCPU_FPR24, kvm_vcpu_arch, fpu.fpr[24]);
+	OFFSET(VCPU_FPR25, kvm_vcpu_arch, fpu.fpr[25]);
+	OFFSET(VCPU_FPR26, kvm_vcpu_arch, fpu.fpr[26]);
+	OFFSET(VCPU_FPR27, kvm_vcpu_arch, fpu.fpr[27]);
+	OFFSET(VCPU_FPR28, kvm_vcpu_arch, fpu.fpr[28]);
+	OFFSET(VCPU_FPR29, kvm_vcpu_arch, fpu.fpr[29]);
+	OFFSET(VCPU_FPR30, kvm_vcpu_arch, fpu.fpr[30]);
+	OFFSET(VCPU_FPR31, kvm_vcpu_arch, fpu.fpr[31]);
+
+	OFFSET(VCPU_FCR31, kvm_vcpu_arch, fpu.fcr31);
+	OFFSET(VCPU_MSA_CSR, kvm_vcpu_arch, fpu.msacsr);
+	BLANK();
+}
+#endif
+
+#ifdef CONFIG_MIPS_CPS
+void output_cps_defines(void)
+{
+	COMMENT(" MIPS CPS offsets. ");
+
+	OFFSET(COREBOOTCFG_VPEMASK, core_boot_config, vpe_mask);
+	OFFSET(COREBOOTCFG_VPECONFIG, core_boot_config, vpe_config);
+	DEFINE(COREBOOTCFG_SIZE, sizeof(struct core_boot_config));
+
+	OFFSET(VPEBOOTCFG_PC, vpe_boot_config, pc);
+	OFFSET(VPEBOOTCFG_SP, vpe_boot_config, sp);
+	OFFSET(VPEBOOTCFG_GP, vpe_boot_config, gp);
+	DEFINE(VPEBOOTCFG_SIZE, sizeof(struct vpe_boot_config));
+}
+#endif
diff --git a/arch/mips/kernel/bmips_5xxx_init.S b/arch/mips/kernel/bmips_5xxx_init.S
new file mode 100644
index 000000000..9e422d186
--- /dev/null
+++ b/arch/mips/kernel/bmips_5xxx_init.S
@@ -0,0 +1,747 @@
+
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2011-2012 by Broadcom Corporation
+ *
+ * Init for bmips 5000.
+ * Used to init second core in dual core 5000's.
+ */
+
+#include <linux/init.h>
+
+#include <asm/asm.h>
+#include <asm/asmmacro.h>
+#include <asm/cacheops.h>
+#include <asm/regdef.h>
+#include <asm/mipsregs.h>
+#include <asm/stackframe.h>
+#include <asm/addrspace.h>
+#include <asm/hazards.h>
+#include <asm/bmips.h>
+
+#ifdef CONFIG_CPU_BMIPS5000
+
+
+#define cacheop(kva, size, linesize, op) 	\
+	.set noreorder			;	\
+	addu		t1, kva, size	;	\
+	subu		t2, linesize, 1	;	\
+	not		t2		;	\
+	and		t0, kva, t2	;	\
+	addiu		t1, t1, -1	;	\
+	and		t1, t2		;	\
+9:	cache		op, 0(t0)	;	\
+	bne		t0, t1, 9b	;	\
+	 addu		t0, linesize	;	\
+	.set reorder			;
+
+
+
+#define	IS_SHIFT	22
+#define	IL_SHIFT	19
+#define	IA_SHIFT	16
+#define	DS_SHIFT	13
+#define	DL_SHIFT	10
+#define	DA_SHIFT	 7
+#define	IS_MASK		 7
+#define	IL_MASK		 7
+#define	IA_MASK		 7
+#define	DS_MASK		 7
+#define	DL_MASK		 7
+#define	DA_MASK		 7
+#define	ICE_MASK	0x80000000
+#define	DCE_MASK	0x40000000
+
+#define CP0_BRCM_CONFIG0	$22, 0
+#define CP0_BRCM_MODE		$22, 1
+#define	CP0_CONFIG_K0_MASK	7
+
+#define CP0_ICACHE_TAG_LO	$28
+#define CP0_ICACHE_DATA_LO	$28, 1
+#define CP0_DCACHE_TAG_LO	$28, 2
+#define CP0_D_SEC_CACHE_DATA_LO	$28, 3
+#define CP0_ICACHE_TAG_HI	$29
+#define CP0_ICACHE_DATA_HI	$29, 1
+#define CP0_DCACHE_TAG_HI	$29, 2
+
+#define CP0_BRCM_MODE_Luc_MASK		(1 << 11)
+#define	CP0_BRCM_CONFIG0_CWF_MASK	(1 << 20)
+#define	CP0_BRCM_CONFIG0_TSE_MASK	(1 << 19)
+#define CP0_BRCM_MODE_SET_MASK		(1 << 7)
+#define CP0_BRCM_MODE_ClkRATIO_MASK	(7 << 4)
+#define CP0_BRCM_MODE_BrPRED_MASK 	(3 << 24)
+#define CP0_BRCM_MODE_BrPRED_SHIFT	24
+#define CP0_BRCM_MODE_BrHIST_MASK 	(0x1f << 20)
+#define CP0_BRCM_MODE_BrHIST_SHIFT	20
+
+/* ZSC L2 Cache Register Access Register Definitions */
+#define BRCM_ZSC_ALL_REGS_SELECT		0x7 << 24
+
+#define BRCM_ZSC_CONFIG_REG			0 << 3
+#define BRCM_ZSC_REQ_BUFFER_REG			2 << 3
+#define BRCM_ZSC_RBUS_ADDR_MAPPING_REG0		4 << 3
+#define BRCM_ZSC_RBUS_ADDR_MAPPING_REG1		6 << 3
+#define BRCM_ZSC_RBUS_ADDR_MAPPING_REG2		8 << 3
+
+#define BRCM_ZSC_SCB0_ADDR_MAPPING_REG0		0xa << 3
+#define BRCM_ZSC_SCB0_ADDR_MAPPING_REG1		0xc << 3
+
+#define BRCM_ZSC_SCB1_ADDR_MAPPING_REG0		0xe << 3
+#define BRCM_ZSC_SCB1_ADDR_MAPPING_REG1		0x10 << 3
+
+#define BRCM_ZSC_CONFIG_LMB1En			1 << (15)
+#define BRCM_ZSC_CONFIG_LMB0En			1 << (14)
+
+/* branch predition values */
+
+#define BRCM_BrPRED_ALL_TAKEN		(0x0)
+#define BRCM_BrPRED_ALL_NOT_TAKEN	(0x1)
+#define BRCM_BrPRED_BHT_ENABLE		(0x2)
+#define BRCM_BrPRED_PREDICT_BACKWARD	(0x3)
+
+
+
+.align 2
+/*
+ * Function: 	size_i_cache
+ * Arguments: 	None
+ * Returns:	v0 = i cache size, v1 = I cache line size
+ * Description: compute the I-cache size and I-cache line size
+ * Trashes:	v0, v1, a0, t0
+ *
+ *	pseudo code:
+ *
+ */
+
+LEAF(size_i_cache)
+	.set	noreorder
+
+	mfc0	a0, CP0_CONFIG, 1
+	move	t0, a0
+
+	/*
+	 * Determine sets per way: IS
+	 *
+	 * This field contains the number of sets (i.e., indices) per way of
+	 * the instruction cache:
+	 * i) 0x0: 64, ii) 0x1: 128, iii) 0x2: 256, iv) 0x3: 512, v) 0x4: 1k
+	 * vi) 0x5 - 0x7: Reserved.
+	 */
+
+	srl	a0, a0, IS_SHIFT
+	and	a0, a0, IS_MASK
+
+	/* sets per way = (64<<IS) */
+
+	li	v0, 0x40
+	sllv	v0, v0, a0
+
+	/*
+	 * Determine line size
+	 *
+	 * This field contains the line size of the instruction cache:
+	 * i) 0x0: No I-cache present, i) 0x3: 16 bytes, ii) 0x4: 32 bytes, iii)
+	 * 0x5: 64 bytes, iv) the rest: Reserved.
+	 */
+
+	move	a0, t0
+
+	srl	a0, a0, IL_SHIFT
+	and	a0, a0, IL_MASK
+
+	beqz	a0, no_i_cache
+	nop
+
+	/* line size = 2 ^ (IL+1) */
+
+	addi	a0, a0, 1
+	li	v1, 1
+	sll	v1, v1, a0
+
+	/* v0 now have sets per way, multiply it by line size now
+	 * that will give the set size
+	 */
+
+	sll	v0, v0, a0
+
+	/*
+	 * Determine set associativity
+	 *
+	 * This field contains the set associativity of the instruction cache.
+	 * i) 0x0: Direct mapped, ii) 0x1: 2-way, iii) 0x2: 3-way, iv) 0x3:
+	 * 4-way, v) 0x4 - 0x7: Reserved.
+	 */
+
+	move	a0, t0
+
+	srl	a0, a0, IA_SHIFT
+	and	a0, a0, IA_MASK
+	addi	a0, a0, 0x1
+
+	/* v0 has the set size, multiply it by
+	 * set associativiy, to get the cache size
+	 */
+
+	multu	v0, a0	/*multu is interlocked, so no need to insert nops */
+	mflo	v0
+	b	1f
+	nop
+
+no_i_cache:
+	move	v0, zero
+	move	v1, zero
+1:
+	jr	ra
+	nop
+	.set	reorder
+
+END(size_i_cache)
+
+/*
+ * Function: 	size_d_cache
+ * Arguments: 	None
+ * Returns:	v0 = d cache size, v1 = d cache line size
+ * Description: compute the D-cache size and D-cache line size.
+ * Trashes:	v0, v1, a0, t0
+ *
+ */
+
+LEAF(size_d_cache)
+	.set	noreorder
+
+	mfc0	a0, CP0_CONFIG, 1
+	move	t0, a0
+
+	/*
+	 * Determine sets per way: IS
+	 *
+	 * This field contains the number of sets (i.e., indices) per way of
+	 * the instruction cache:
+	 * i) 0x0: 64, ii) 0x1: 128, iii) 0x2: 256, iv) 0x3: 512, v) 0x4: 1k
+	 * vi) 0x5 - 0x7: Reserved.
+	 */
+
+	srl	a0, a0, DS_SHIFT
+	and	a0, a0, DS_MASK
+
+	/* sets per way = (64<<IS) */
+
+	li	v0, 0x40
+	sllv	v0, v0, a0
+
+	/*
+	 * Determine line size
+	 *
+	 * This field contains the line size of the instruction cache:
+	 * i) 0x0: No I-cache present, i) 0x3: 16 bytes, ii) 0x4: 32 bytes, iii)
+	 * 0x5: 64 bytes, iv) the rest: Reserved.
+	 */
+	move	a0, t0
+
+	srl	a0, a0, DL_SHIFT
+	and	a0, a0, DL_MASK
+
+	beqz	a0, no_d_cache
+	nop
+
+	/* line size = 2 ^ (IL+1) */
+
+	addi	a0, a0, 1
+	li	v1, 1
+	sll	v1, v1, a0
+
+	/* v0 now have sets per way, multiply it by line size now
+	 * that will give the set size
+	 */
+
+	sll	v0, v0, a0
+
+	/* determine set associativity
+	 *
+	 * This field contains the set associativity of the instruction cache.
+	 * i) 0x0: Direct mapped, ii) 0x1: 2-way, iii) 0x2: 3-way, iv) 0x3:
+	 * 4-way, v) 0x4 - 0x7: Reserved.
+	 */
+
+	move	a0, t0
+
+	srl	a0, a0, DA_SHIFT
+	and	a0, a0, DA_MASK
+	addi	a0, a0, 0x1
+
+	/* v0 has the set size, multiply it by
+	 * set associativiy, to get the cache size
+	 */
+
+	multu	v0, a0	/*multu is interlocked, so no need to insert nops */
+	mflo	v0
+
+	b	1f
+	nop
+
+no_d_cache:
+	move	v0, zero
+	move	v1, zero
+1:
+	jr	ra
+	nop
+	.set	reorder
+
+END(size_d_cache)
+
+
+/*
+ * Function: enable_ID
+ * Arguments: 	None
+ * Returns:	None
+ * Description: Enable I and D caches, initialize I and D-caches, also set
+ *		hardware delay for d-cache (TP0).
+ * Trashes:	t0
+ *
+ */
+	.global	enable_ID
+	.ent	enable_ID
+	.set	noreorder
+enable_ID:
+	mfc0	t0, CP0_BRCM_CONFIG0
+	or	t0, t0, (ICE_MASK | DCE_MASK)
+	mtc0	t0, CP0_BRCM_CONFIG0
+	jr	ra
+	nop
+
+	.end	enable_ID
+	.set	reorder
+
+
+/*
+ * Function: l1_init
+ * Arguments: 	None
+ * Returns:	None
+ * Description: Enable I and D caches, and initialize I and D-caches
+ * Trashes:	a0, v0, v1, t0, t1, t2, t8
+ *
+ */
+	.globl	l1_init
+	.ent	l1_init
+	.set	noreorder
+l1_init:
+
+	/* save return address */
+	move	t8, ra
+
+
+	/* initialize I and D cache Data and Tag registers.  */
+	mtc0	zero, CP0_ICACHE_TAG_LO
+	mtc0	zero, CP0_ICACHE_TAG_HI
+	mtc0	zero, CP0_ICACHE_DATA_LO
+	mtc0	zero, CP0_ICACHE_DATA_HI
+	mtc0	zero, CP0_DCACHE_TAG_LO
+	mtc0	zero, CP0_DCACHE_TAG_HI
+
+	/* Enable Caches before Clearing. If the caches are disabled
+	 * then the cache operations to clear the cache will be ignored
+	 */
+
+	jal	enable_ID
+	nop
+
+	jal	size_i_cache	/* v0 = i-cache size, v1 = i-cache line size */
+	nop
+
+	/* run uncached in kseg 1 */
+	la	k0, 1f
+	lui	k1, 0x2000
+	or	k0, k1, k0
+	jr	k0
+	nop
+1:
+
+	/*
+	 * set K0 cache mode
+	 */
+
+	mfc0	t0, CP0_CONFIG
+	and	t0, t0, ~CP0_CONFIG_K0_MASK
+	or	t0, t0, 3	/* Write Back mode */
+	mtc0	t0, CP0_CONFIG
+
+	/*
+	 * Initialize instruction cache.
+	 */
+
+	li	a0, KSEG0
+	cacheop(a0, v0, v1, Index_Store_Tag_I)
+
+	/*
+	 * Now we can run from I-$, kseg 0
+	 */
+	la	k0, 1f
+	lui	k1, 0x2000
+	or	k0, k1, k0
+	xor	k0, k1, k0
+	jr	k0
+	nop
+1:
+	/*
+	 * Initialize data cache.
+	 */
+
+	jal	size_d_cache	/* v0 = d-cache size, v1 = d-cache line size */
+	nop
+
+
+	li	a0, KSEG0
+	cacheop(a0, v0, v1, Index_Store_Tag_D)
+
+	jr	t8
+	nop
+
+	.end 	l1_init
+	.set	reorder
+
+
+/*
+ * Function: 	set_other_config
+ * Arguments:	none
+ * Returns:	None
+ * Description: initialize other remainder configuration to defaults.
+ * Trashes:	t0, t1
+ *
+ *	pseudo code:
+ *
+ */
+LEAF(set_other_config)
+	.set noreorder
+
+	/* enable Bus error for I-fetch */
+	mfc0	t0, CP0_CACHEERR, 0
+	li	t1, 0x4
+	or	t0, t1
+	mtc0	t0, CP0_CACHEERR, 0
+
+	/* enable Bus error for Load */
+	mfc0	t0, CP0_CACHEERR, 1
+	li	t1, 0x4
+	or	t0, t1
+	mtc0	t0, CP0_CACHEERR, 1
+
+	/* enable Bus Error for Store */
+	mfc0	t0, CP0_CACHEERR, 2
+	li	t1, 0x4
+	or	t0, t1
+	mtc0	t0, CP0_CACHEERR, 2
+
+	jr	ra
+	nop
+	.set reorder
+END(set_other_config)
+
+/*
+ * Function: 	set_branch_pred
+ * Arguments:	none
+ * Returns:	None
+ * Description:
+ * Trashes:	t0, t1
+ *
+ *	pseudo code:
+ *
+ */
+
+LEAF(set_branch_pred)
+	.set noreorder
+	mfc0	t0, CP0_BRCM_MODE
+	li	t1, ~(CP0_BRCM_MODE_BrPRED_MASK | CP0_BRCM_MODE_BrHIST_MASK )
+	and	t0, t0, t1
+
+	/* enable Branch prediction */
+	li	t1, BRCM_BrPRED_BHT_ENABLE
+	sll	t1, CP0_BRCM_MODE_BrPRED_SHIFT
+	or	t0, t0, t1
+
+	/* set history count to 8 */
+	li	t1, 8
+	sll	t1, CP0_BRCM_MODE_BrHIST_SHIFT
+	or	t0, t0, t1
+
+	mtc0	t0, CP0_BRCM_MODE
+	jr	ra
+	nop
+	.set	reorder
+END(set_branch_pred)
+
+
+/*
+ * Function: 	set_luc
+ * Arguments:	set link uncached.
+ * Returns:	None
+ * Description:
+ * Trashes:	t0, t1
+ *
+ */
+LEAF(set_luc)
+	.set noreorder
+	mfc0	t0, CP0_BRCM_MODE
+	li	t1, ~(CP0_BRCM_MODE_Luc_MASK)
+	and	t0, t0, t1
+
+	/* set Luc */
+	ori	t0, t0, CP0_BRCM_MODE_Luc_MASK
+
+	mtc0	t0, CP0_BRCM_MODE
+	jr	ra
+	nop
+	.set	reorder
+END(set_luc)
+
+/*
+ * Function: 	set_cwf_tse
+ * Arguments:	set CWF and TSE bits
+ * Returns:	None
+ * Description:
+ * Trashes:	t0, t1
+ *
+ */
+LEAF(set_cwf_tse)
+	.set noreorder
+	mfc0	t0, CP0_BRCM_CONFIG0
+	li	t1, (CP0_BRCM_CONFIG0_CWF_MASK | CP0_BRCM_CONFIG0_TSE_MASK)
+	or	t0, t0, t1
+
+	mtc0	t0, CP0_BRCM_CONFIG0
+	jr	ra
+	nop
+	.set	reorder
+END(set_cwf_tse)
+
+/*
+ * Function: 	set_clock_ratio
+ * Arguments:	set clock ratio specified by a0
+ * Returns:	None
+ * Description:
+ * Trashes:	v0, v1, a0, a1
+ *
+ *	pseudo code:
+ *
+ */
+LEAF(set_clock_ratio)
+	.set noreorder
+
+	mfc0	t0, CP0_BRCM_MODE
+	li	t1, ~(CP0_BRCM_MODE_SET_MASK | CP0_BRCM_MODE_ClkRATIO_MASK)
+	and	t0, t0, t1
+	li	t1, CP0_BRCM_MODE_SET_MASK
+	or	t0, t0, t1
+	or	t0, t0, a0
+	mtc0	t0, CP0_BRCM_MODE
+	jr	ra
+	nop
+	.set	reorder
+END(set_clock_ratio)
+/*
+ * Function: set_zephyr
+ * Arguments:	None
+ * Returns:	None
+ * Description: Set any zephyr bits
+ * Trashes:	t0 & t1
+ *
+ */
+LEAF(set_zephyr)
+	.set	noreorder
+
+	/* enable read/write of CP0 #22 sel. 8 */
+	li	t0, 0x5a455048
+	.word	0x4088b00f	/* mtc0    t0, $22, 15 */
+
+	.word	0x4008b008	/* mfc0    t0, $22, 8 */
+	li	t1, 0x09008000	/* turn off pref, jtb */
+	or	t0, t0, t1
+	.word	0x4088b008	/* mtc0    t0, $22, 8 */
+	sync
+
+	/* disable read/write of CP0 #22 sel 8 */
+	li	t0, 0x0
+	.word	0x4088b00f	/* mtc0    t0, $22, 15 */
+
+
+	jr	ra
+	nop
+	.set reorder
+
+END(set_zephyr)
+
+
+/*
+ * Function:	set_llmb
+ * Arguments:	a0=0 disable llmb, a0=1 enables llmb
+ * Returns:	None
+ * Description:
+ * Trashes:	t0, t1, t2
+ *
+ *      pseudo code:
+ *
+ */
+LEAF(set_llmb)
+	.set noreorder
+
+	li	t2, 0x90000000 | BRCM_ZSC_ALL_REGS_SELECT | BRCM_ZSC_CONFIG_REG
+	sync
+	cache	0x7, 0x0(t2)
+	sync
+	mfc0	t0, CP0_D_SEC_CACHE_DATA_LO
+	li	t1, ~(BRCM_ZSC_CONFIG_LMB1En | BRCM_ZSC_CONFIG_LMB0En)
+	and	t0, t0, t1
+
+	beqz	a0, svlmb
+	nop
+
+enable_lmb:
+	li	t1, (BRCM_ZSC_CONFIG_LMB1En | BRCM_ZSC_CONFIG_LMB0En)
+	or	t0, t0, t1
+
+svlmb:
+	mtc0	t0, CP0_D_SEC_CACHE_DATA_LO
+	sync
+	cache	0xb, 0x0(t2)
+	sync
+
+	jr	ra
+	nop
+	.set reorder
+
+END(set_llmb)
+/*
+ * Function: 	core_init
+ * Arguments:	none
+ * Returns:	None
+ * Description: initialize core related configuration
+ * Trashes:	v0,v1,a0,a1,t8
+ *
+ *	pseudo code:
+ *
+ */
+	.globl	core_init
+	.ent	core_init
+	.set	noreorder
+core_init:
+	move	t8, ra
+
+	/* set Zephyr bits. */
+	bal	set_zephyr
+	nop
+
+	/* set low latency memory bus */
+	li	a0, 1
+	bal	set_llmb
+	nop
+
+	/* set branch prediction (TP0 only) */
+	bal	set_branch_pred
+	nop
+
+	/* set link uncached */
+	bal	set_luc
+	nop
+
+	/* set CWF and TSE */
+	bal	set_cwf_tse
+	nop
+
+	/*
+	 *set clock ratio by setting 1 to 'set'
+	 * and 0 to ClkRatio, (TP0 only)
+	 */
+	li	a0, 0
+	bal	set_clock_ratio
+	nop
+
+	/* set other configuration to defaults */
+	bal	set_other_config
+	nop
+
+	move	ra, t8
+	jr	ra
+	nop
+
+	.set reorder
+	.end	core_init
+
+/*
+ * Function: 	clear_jump_target_buffer
+ * Arguments:	None
+ * Returns:	None
+ * Description:
+ * Trashes:	t0, t1, t2
+ *
+ */
+#define RESET_CALL_RETURN_STACK_THIS_THREAD		(0x06<<16)
+#define RESET_JUMP_TARGET_BUFFER_THIS_THREAD		(0x04<<16)
+#define JTB_CS_CNTL_MASK				(0xFF<<16)
+
+	.globl	clear_jump_target_buffer
+	.ent	clear_jump_target_buffer
+	.set	noreorder
+clear_jump_target_buffer:
+
+	mfc0	t0, $22, 2
+	nop
+	nop
+
+	li	t1, ~JTB_CS_CNTL_MASK
+	and	t0, t0, t1
+	li	t2, RESET_CALL_RETURN_STACK_THIS_THREAD
+	or	t0, t0, t2
+	mtc0	t0, $22, 2
+	nop
+	nop
+
+	and	t0, t0, t1
+	li	t2, RESET_JUMP_TARGET_BUFFER_THIS_THREAD
+	or	t0, t0, t2
+	mtc0	t0, $22, 2
+	nop
+	nop
+	jr	ra
+	nop
+
+	.end	clear_jump_target_buffer
+	.set	reorder
+/*
+ * Function: 	bmips_cache_init
+ * Arguments: 	None
+ * Returns:	None
+ * Description: Enable I and D caches, and initialize I and D-caches
+ * Trashes:	v0, v1, t0, t1, t2, t5, t7, t8
+ *
+ */
+	.globl	bmips_5xxx_init
+	.ent	bmips_5xxx_init
+	.set	noreorder
+bmips_5xxx_init:
+
+	/* save return address and A0 */
+	move	t7, ra
+	move	t5, a0
+
+	jal	l1_init
+	nop
+
+	jal	core_init
+	nop
+
+	jal	clear_jump_target_buffer
+	nop
+
+	mtc0	zero, CP0_CAUSE
+
+	move 	a0, t5
+	jr	t7
+	nop
+
+	.end 	bmips_5xxx_init
+	.set	reorder
+
+
+#endif
diff --git a/arch/mips/kernel/bmips_vec.S b/arch/mips/kernel/bmips_vec.S
new file mode 100644
index 000000000..921a5fa55
--- /dev/null
+++ b/arch/mips/kernel/bmips_vec.S
@@ -0,0 +1,322 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2011 by Kevin Cernekee (cernekee@gmail.com)
+ *
+ * Reset/NMI/re-entry vectors for BMIPS processors
+ */
+
+
+#include <asm/asm.h>
+#include <asm/asmmacro.h>
+#include <asm/cacheops.h>
+#include <asm/cpu.h>
+#include <asm/regdef.h>
+#include <asm/mipsregs.h>
+#include <asm/stackframe.h>
+#include <asm/addrspace.h>
+#include <asm/hazards.h>
+#include <asm/bmips.h>
+
+	.macro	BARRIER
+	.set	mips32
+	_ssnop
+	_ssnop
+	_ssnop
+	.set	mips0
+	.endm
+
+/***********************************************************************
+ * Alternate CPU1 startup vector for BMIPS4350
+ *
+ * On some systems the bootloader has already started CPU1 and configured
+ * it to resume execution at 0x8000_0200 (!BEV IV vector) when it is
+ * triggered by the SW1 interrupt.  If that is the case we try to move
+ * it to a more convenient place: BMIPS_WARM_RESTART_VEC @ 0x8000_0380.
+ ***********************************************************************/
+
+LEAF(bmips_smp_movevec)
+	la	k0, 1f
+	li	k1, CKSEG1
+	or	k0, k1
+	jr	k0
+
+1:
+	/* clear IV, pending IPIs */
+	mtc0	zero, CP0_CAUSE
+
+	/* re-enable IRQs to wait for SW1 */
+	li	k0, ST0_IE | ST0_BEV | STATUSF_IP1
+	mtc0	k0, CP0_STATUS
+
+	/* set up CPU1 CBR; move BASE to 0xa000_0000 */
+	li	k0, 0xff400000
+	mtc0	k0, $22, 6
+	/* set up relocation vector address based on thread ID */
+	mfc0	k1, $22, 3
+	srl	k1, 16
+	andi	k1, 0x8000
+	or	k1, CKSEG1 | BMIPS_RELO_VECTOR_CONTROL_0
+	or	k0, k1
+	li	k1, 0xa0080000
+	sw	k1, 0(k0)
+
+	/* wait here for SW1 interrupt from bmips_boot_secondary() */
+	wait
+
+	la	k0, bmips_reset_nmi_vec
+	li	k1, CKSEG1
+	or	k0, k1
+	jr	k0
+END(bmips_smp_movevec)
+
+/***********************************************************************
+ * Reset/NMI vector
+ * For BMIPS processors that can relocate their exception vectors, this
+ * entire function gets copied to 0x8000_0000.
+ ***********************************************************************/
+
+NESTED(bmips_reset_nmi_vec, PT_SIZE, sp)
+	.set	push
+	.set	noat
+	.align	4
+
+#ifdef CONFIG_SMP
+	/* if the NMI bit is clear, assume this is a CPU1 reset instead */
+	li	k1, (1 << 19)
+	mfc0	k0, CP0_STATUS
+	and	k0, k1
+	beqz	k0, soft_reset
+
+#if defined(CONFIG_CPU_BMIPS5000)
+	mfc0	k0, CP0_PRID
+	li	k1, PRID_IMP_BMIPS5000
+	/* mask with PRID_IMP_BMIPS5000 to cover both variants */
+	andi	k0, PRID_IMP_BMIPS5000
+	bne	k0, k1, 1f
+
+	/* if we're not on core 0, this must be the SMP boot signal */
+	li	k1, (3 << 25)
+	mfc0	k0, $22
+	and	k0, k1
+	bnez	k0, bmips_smp_entry
+1:
+#endif /* CONFIG_CPU_BMIPS5000 */
+#endif /* CONFIG_SMP */
+
+	/* nope, it's just a regular NMI */
+	SAVE_ALL
+	move	a0, sp
+
+	/* clear EXL, ERL, BEV so that TLB refills still work */
+	mfc0	k0, CP0_STATUS
+	li	k1, ST0_ERL | ST0_EXL | ST0_BEV | ST0_IE
+	or	k0, k1
+	xor	k0, k1
+	mtc0	k0, CP0_STATUS
+	BARRIER
+
+	/* jump to the NMI handler function */
+	la	k0, nmi_handler
+	jr	k0
+
+	RESTORE_ALL
+	.set	arch=r4000
+	eret
+
+#ifdef CONFIG_SMP
+soft_reset:
+
+#if defined(CONFIG_CPU_BMIPS5000)
+	mfc0	k0, CP0_PRID
+	andi	k0, 0xff00
+	li	k1, PRID_IMP_BMIPS5200
+	bne	k0, k1, bmips_smp_entry
+
+        /* if running on TP 1, jump  to  bmips_smp_entry */
+        mfc0    k0, $22
+        li      k1, (1 << 24)
+        and     k1, k0
+        bnez    k1, bmips_smp_entry
+        nop
+
+        /*
+         * running on TP0, can not be core 0 (the boot core).
+         * Check for soft reset.  Indicates a warm boot
+         */
+        mfc0    k0, $12
+        li      k1, (1 << 20)
+        and     k0, k1
+        beqz    k0, bmips_smp_entry
+
+        /*
+         * Warm boot.
+         * Cache init is only done on TP0
+         */
+        la      k0, bmips_5xxx_init
+        jalr    k0
+        nop
+
+        b       bmips_smp_entry
+        nop
+#endif
+
+/***********************************************************************
+ * CPU1 reset vector (used for the initial boot only)
+ * This is still part of bmips_reset_nmi_vec().
+ ***********************************************************************/
+
+bmips_smp_entry:
+
+	/* set up CP0 STATUS; enable FPU */
+	li	k0, 0x30000000
+	mtc0	k0, CP0_STATUS
+	BARRIER
+
+	/* set local CP0 CONFIG to make kseg0 cacheable, write-back */
+	mfc0	k0, CP0_CONFIG
+	ori	k0, 0x07
+	xori	k0, 0x04
+	mtc0	k0, CP0_CONFIG
+
+	mfc0	k0, CP0_PRID
+	andi	k0, 0xff00
+#if defined(CONFIG_CPU_BMIPS4350) || defined(CONFIG_CPU_BMIPS4380)
+	li	k1, PRID_IMP_BMIPS43XX
+	bne	k0, k1, 2f
+
+	/* initialize CPU1's local I-cache */
+	li	k0, 0x80000000
+	li	k1, 0x80010000
+	mtc0	zero, $28
+	mtc0	zero, $28, 1
+	BARRIER
+
+1:	cache	Index_Store_Tag_I, 0(k0)
+	addiu	k0, 16
+	bne	k0, k1, 1b
+
+	b	3f
+2:
+#endif /* CONFIG_CPU_BMIPS4350 || CONFIG_CPU_BMIPS4380 */
+#if defined(CONFIG_CPU_BMIPS5000)
+	/* mask with PRID_IMP_BMIPS5000 to cover both variants */
+	li	k1, PRID_IMP_BMIPS5000
+	andi	k0, PRID_IMP_BMIPS5000
+	bne	k0, k1, 3f
+
+	/* set exception vector base */
+	la	k0, ebase
+	lw	k0, 0(k0)
+	mtc0	k0, $15, 1
+	BARRIER
+#endif /* CONFIG_CPU_BMIPS5000 */
+3:
+	/* jump back to kseg0 in case we need to remap the kseg1 area */
+	la	k0, 1f
+	jr	k0
+1:
+	la	k0, bmips_enable_xks01
+	jalr	k0
+
+	/* use temporary stack to set up upper memory TLB */
+	li	sp, BMIPS_WARM_RESTART_VEC
+	la	k0, plat_wired_tlb_setup
+	jalr	k0
+
+	/* switch to permanent stack and continue booting */
+
+	.global bmips_secondary_reentry
+bmips_secondary_reentry:
+	la	k0, bmips_smp_boot_sp
+	lw	sp, 0(k0)
+	la	k0, bmips_smp_boot_gp
+	lw	gp, 0(k0)
+	la	k0, start_secondary
+	jr	k0
+
+#endif /* CONFIG_SMP */
+
+	.align	4
+	.global bmips_reset_nmi_vec_end
+bmips_reset_nmi_vec_end:
+
+END(bmips_reset_nmi_vec)
+
+	.set	pop
+
+/***********************************************************************
+ * CPU1 warm restart vector (used for second and subsequent boots).
+ * Also used for S2 standby recovery (PM).
+ * This entire function gets copied to (BMIPS_WARM_RESTART_VEC)
+ ***********************************************************************/
+
+LEAF(bmips_smp_int_vec)
+
+	.align	4
+	mfc0	k0, CP0_STATUS
+	ori	k0, 0x01
+	xori	k0, 0x01
+	mtc0	k0, CP0_STATUS
+	eret
+
+	.align	4
+	.global bmips_smp_int_vec_end
+bmips_smp_int_vec_end:
+
+END(bmips_smp_int_vec)
+
+/***********************************************************************
+ * XKS01 support
+ * Certain CPUs support extending kseg0 to 1024MB.
+ ***********************************************************************/
+
+LEAF(bmips_enable_xks01)
+
+#if defined(CONFIG_XKS01)
+	mfc0	t0, CP0_PRID
+	andi	t2, t0, 0xff00
+#if defined(CONFIG_CPU_BMIPS4380)
+	li	t1, PRID_IMP_BMIPS43XX
+	bne	t2, t1, 1f
+
+	andi	t0, 0xff
+	addiu	t1, t0, -PRID_REV_BMIPS4380_HI
+	bgtz	t1, 2f
+	addiu	t0, -PRID_REV_BMIPS4380_LO
+	bltz	t0, 2f
+
+	mfc0	t0, $22, 3
+	li	t1, 0x1ff0
+	li	t2, (1 << 12) | (1 << 9)
+	or	t0, t1
+	xor	t0, t1
+	or	t0, t2
+	mtc0	t0, $22, 3
+	BARRIER
+	b	2f
+1:
+#endif /* CONFIG_CPU_BMIPS4380 */
+#if defined(CONFIG_CPU_BMIPS5000)
+	li	t1, PRID_IMP_BMIPS5000
+	/* mask with PRID_IMP_BMIPS5000 to cover both variants */
+	andi	t2, PRID_IMP_BMIPS5000
+	bne	t2, t1, 2f
+
+	mfc0	t0, $22, 5
+	li	t1, 0x01ff
+	li	t2, (1 << 8) | (1 << 5)
+	or	t0, t1
+	xor	t0, t1
+	or	t0, t2
+	mtc0	t0, $22, 5
+	BARRIER
+#endif /* CONFIG_CPU_BMIPS5000 */
+2:
+#endif /* defined(CONFIG_XKS01) */
+
+	jr	ra
+
+END(bmips_enable_xks01)
diff --git a/arch/mips/kernel/branch.c b/arch/mips/kernel/branch.c
new file mode 100644
index 000000000..0216ff24c
--- /dev/null
+++ b/arch/mips/kernel/branch.c
@@ -0,0 +1,908 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1996, 97, 2000, 2001 by Ralf Baechle
+ * Copyright (C) 2001 MIPS Technologies, Inc.
+ */
+#include <linux/kernel.h>
+#include <linux/sched/signal.h>
+#include <linux/signal.h>
+#include <linux/export.h>
+#include <asm/branch.h>
+#include <asm/cpu.h>
+#include <asm/cpu-features.h>
+#include <asm/fpu.h>
+#include <asm/fpu_emulator.h>
+#include <asm/inst.h>
+#include <asm/mips-r2-to-r6-emul.h>
+#include <asm/ptrace.h>
+#include <linux/uaccess.h>
+
+#include "probes-common.h"
+
+/*
+ * Calculate and return exception PC in case of branch delay slot
+ * for microMIPS and MIPS16e. It does not clear the ISA mode bit.
+ */
+int __isa_exception_epc(struct pt_regs *regs)
+{
+	unsigned short inst;
+	long epc = regs->cp0_epc;
+
+	/* Calculate exception PC in branch delay slot. */
+	if (__get_user(inst, (u16 __user *) msk_isa16_mode(epc))) {
+		/* This should never happen because delay slot was checked. */
+		force_sig(SIGSEGV);
+		return epc;
+	}
+	if (cpu_has_mips16) {
+		union mips16e_instruction inst_mips16e;
+
+		inst_mips16e.full = inst;
+		if (inst_mips16e.ri.opcode == MIPS16e_jal_op)
+			epc += 4;
+		else
+			epc += 2;
+	} else if (mm_insn_16bit(inst))
+		epc += 2;
+	else
+		epc += 4;
+
+	return epc;
+}
+
+/* (microMIPS) Convert 16-bit register encoding to 32-bit register encoding. */
+static const unsigned int reg16to32map[8] = {16, 17, 2, 3, 4, 5, 6, 7};
+
+int __mm_isBranchInstr(struct pt_regs *regs, struct mm_decoded_insn dec_insn,
+		       unsigned long *contpc)
+{
+	union mips_instruction insn = (union mips_instruction)dec_insn.insn;
+	int __maybe_unused bc_false = 0;
+
+	if (!cpu_has_mmips)
+		return 0;
+
+	switch (insn.mm_i_format.opcode) {
+	case mm_pool32a_op:
+		if ((insn.mm_i_format.simmediate & MM_POOL32A_MINOR_MASK) ==
+		    mm_pool32axf_op) {
+			switch (insn.mm_i_format.simmediate >>
+				MM_POOL32A_MINOR_SHIFT) {
+			case mm_jalr_op:
+			case mm_jalrhb_op:
+			case mm_jalrs_op:
+			case mm_jalrshb_op:
+				if (insn.mm_i_format.rt != 0)	/* Not mm_jr */
+					regs->regs[insn.mm_i_format.rt] =
+						regs->cp0_epc +
+						dec_insn.pc_inc +
+						dec_insn.next_pc_inc;
+				*contpc = regs->regs[insn.mm_i_format.rs];
+				return 1;
+			}
+		}
+		break;
+	case mm_pool32i_op:
+		switch (insn.mm_i_format.rt) {
+		case mm_bltzals_op:
+		case mm_bltzal_op:
+			regs->regs[31] = regs->cp0_epc +
+				dec_insn.pc_inc +
+				dec_insn.next_pc_inc;
+			fallthrough;
+		case mm_bltz_op:
+			if ((long)regs->regs[insn.mm_i_format.rs] < 0)
+				*contpc = regs->cp0_epc +
+					dec_insn.pc_inc +
+					(insn.mm_i_format.simmediate << 1);
+			else
+				*contpc = regs->cp0_epc +
+					dec_insn.pc_inc +
+					dec_insn.next_pc_inc;
+			return 1;
+		case mm_bgezals_op:
+		case mm_bgezal_op:
+			regs->regs[31] = regs->cp0_epc +
+					dec_insn.pc_inc +
+					dec_insn.next_pc_inc;
+			fallthrough;
+		case mm_bgez_op:
+			if ((long)regs->regs[insn.mm_i_format.rs] >= 0)
+				*contpc = regs->cp0_epc +
+					dec_insn.pc_inc +
+					(insn.mm_i_format.simmediate << 1);
+			else
+				*contpc = regs->cp0_epc +
+					dec_insn.pc_inc +
+					dec_insn.next_pc_inc;
+			return 1;
+		case mm_blez_op:
+			if ((long)regs->regs[insn.mm_i_format.rs] <= 0)
+				*contpc = regs->cp0_epc +
+					dec_insn.pc_inc +
+					(insn.mm_i_format.simmediate << 1);
+			else
+				*contpc = regs->cp0_epc +
+					dec_insn.pc_inc +
+					dec_insn.next_pc_inc;
+			return 1;
+		case mm_bgtz_op:
+			if ((long)regs->regs[insn.mm_i_format.rs] <= 0)
+				*contpc = regs->cp0_epc +
+					dec_insn.pc_inc +
+					(insn.mm_i_format.simmediate << 1);
+			else
+				*contpc = regs->cp0_epc +
+					dec_insn.pc_inc +
+					dec_insn.next_pc_inc;
+			return 1;
+#ifdef CONFIG_MIPS_FP_SUPPORT
+		case mm_bc2f_op:
+		case mm_bc1f_op: {
+			unsigned int fcr31;
+			unsigned int bit;
+
+			bc_false = 1;
+			fallthrough;
+		case mm_bc2t_op:
+		case mm_bc1t_op:
+			preempt_disable();
+			if (is_fpu_owner())
+			        fcr31 = read_32bit_cp1_register(CP1_STATUS);
+			else
+				fcr31 = current->thread.fpu.fcr31;
+			preempt_enable();
+
+			if (bc_false)
+				fcr31 = ~fcr31;
+
+			bit = (insn.mm_i_format.rs >> 2);
+			bit += (bit != 0);
+			bit += 23;
+			if (fcr31 & (1 << bit))
+				*contpc = regs->cp0_epc +
+					dec_insn.pc_inc +
+					(insn.mm_i_format.simmediate << 1);
+			else
+				*contpc = regs->cp0_epc +
+					dec_insn.pc_inc + dec_insn.next_pc_inc;
+			return 1;
+		}
+#endif /* CONFIG_MIPS_FP_SUPPORT */
+		}
+		break;
+	case mm_pool16c_op:
+		switch (insn.mm_i_format.rt) {
+		case mm_jalr16_op:
+		case mm_jalrs16_op:
+			regs->regs[31] = regs->cp0_epc +
+				dec_insn.pc_inc + dec_insn.next_pc_inc;
+			fallthrough;
+		case mm_jr16_op:
+			*contpc = regs->regs[insn.mm_i_format.rs];
+			return 1;
+		}
+		break;
+	case mm_beqz16_op:
+		if ((long)regs->regs[reg16to32map[insn.mm_b1_format.rs]] == 0)
+			*contpc = regs->cp0_epc +
+				dec_insn.pc_inc +
+				(insn.mm_b1_format.simmediate << 1);
+		else
+			*contpc = regs->cp0_epc +
+				dec_insn.pc_inc + dec_insn.next_pc_inc;
+		return 1;
+	case mm_bnez16_op:
+		if ((long)regs->regs[reg16to32map[insn.mm_b1_format.rs]] != 0)
+			*contpc = regs->cp0_epc +
+				dec_insn.pc_inc +
+				(insn.mm_b1_format.simmediate << 1);
+		else
+			*contpc = regs->cp0_epc +
+				dec_insn.pc_inc + dec_insn.next_pc_inc;
+		return 1;
+	case mm_b16_op:
+		*contpc = regs->cp0_epc + dec_insn.pc_inc +
+			 (insn.mm_b0_format.simmediate << 1);
+		return 1;
+	case mm_beq32_op:
+		if (regs->regs[insn.mm_i_format.rs] ==
+		    regs->regs[insn.mm_i_format.rt])
+			*contpc = regs->cp0_epc +
+				dec_insn.pc_inc +
+				(insn.mm_i_format.simmediate << 1);
+		else
+			*contpc = regs->cp0_epc +
+				dec_insn.pc_inc +
+				dec_insn.next_pc_inc;
+		return 1;
+	case mm_bne32_op:
+		if (regs->regs[insn.mm_i_format.rs] !=
+		    regs->regs[insn.mm_i_format.rt])
+			*contpc = regs->cp0_epc +
+				dec_insn.pc_inc +
+				(insn.mm_i_format.simmediate << 1);
+		else
+			*contpc = regs->cp0_epc +
+				dec_insn.pc_inc + dec_insn.next_pc_inc;
+		return 1;
+	case mm_jalx32_op:
+		regs->regs[31] = regs->cp0_epc +
+			dec_insn.pc_inc + dec_insn.next_pc_inc;
+		*contpc = regs->cp0_epc + dec_insn.pc_inc;
+		*contpc >>= 28;
+		*contpc <<= 28;
+		*contpc |= (insn.j_format.target << 2);
+		return 1;
+	case mm_jals32_op:
+	case mm_jal32_op:
+		regs->regs[31] = regs->cp0_epc +
+			dec_insn.pc_inc + dec_insn.next_pc_inc;
+		fallthrough;
+	case mm_j32_op:
+		*contpc = regs->cp0_epc + dec_insn.pc_inc;
+		*contpc >>= 27;
+		*contpc <<= 27;
+		*contpc |= (insn.j_format.target << 1);
+		set_isa16_mode(*contpc);
+		return 1;
+	}
+	return 0;
+}
+
+/*
+ * Compute return address and emulate branch in microMIPS mode after an
+ * exception only. It does not handle compact branches/jumps and cannot
+ * be used in interrupt context. (Compact branches/jumps do not cause
+ * exceptions.)
+ */
+int __microMIPS_compute_return_epc(struct pt_regs *regs)
+{
+	u16 __user *pc16;
+	u16 halfword;
+	unsigned int word;
+	unsigned long contpc;
+	struct mm_decoded_insn mminsn = { 0 };
+
+	mminsn.micro_mips_mode = 1;
+
+	/* This load never faults. */
+	pc16 = (unsigned short __user *)msk_isa16_mode(regs->cp0_epc);
+	__get_user(halfword, pc16);
+	pc16++;
+	contpc = regs->cp0_epc + 2;
+	word = ((unsigned int)halfword << 16);
+	mminsn.pc_inc = 2;
+
+	if (!mm_insn_16bit(halfword)) {
+		__get_user(halfword, pc16);
+		pc16++;
+		contpc = regs->cp0_epc + 4;
+		mminsn.pc_inc = 4;
+		word |= halfword;
+	}
+	mminsn.insn = word;
+
+	if (get_user(halfword, pc16))
+		goto sigsegv;
+	mminsn.next_pc_inc = 2;
+	word = ((unsigned int)halfword << 16);
+
+	if (!mm_insn_16bit(halfword)) {
+		pc16++;
+		if (get_user(halfword, pc16))
+			goto sigsegv;
+		mminsn.next_pc_inc = 4;
+		word |= halfword;
+	}
+	mminsn.next_insn = word;
+
+	mm_isBranchInstr(regs, mminsn, &contpc);
+
+	regs->cp0_epc = contpc;
+
+	return 0;
+
+sigsegv:
+	force_sig(SIGSEGV);
+	return -EFAULT;
+}
+
+/*
+ * Compute return address and emulate branch in MIPS16e mode after an
+ * exception only. It does not handle compact branches/jumps and cannot
+ * be used in interrupt context. (Compact branches/jumps do not cause
+ * exceptions.)
+ */
+int __MIPS16e_compute_return_epc(struct pt_regs *regs)
+{
+	u16 __user *addr;
+	union mips16e_instruction inst;
+	u16 inst2;
+	u32 fullinst;
+	long epc;
+
+	epc = regs->cp0_epc;
+
+	/* Read the instruction. */
+	addr = (u16 __user *)msk_isa16_mode(epc);
+	if (__get_user(inst.full, addr)) {
+		force_sig(SIGSEGV);
+		return -EFAULT;
+	}
+
+	switch (inst.ri.opcode) {
+	case MIPS16e_extend_op:
+		regs->cp0_epc += 4;
+		return 0;
+
+		/*
+		 *  JAL and JALX in MIPS16e mode
+		 */
+	case MIPS16e_jal_op:
+		addr += 1;
+		if (__get_user(inst2, addr)) {
+			force_sig(SIGSEGV);
+			return -EFAULT;
+		}
+		fullinst = ((unsigned)inst.full << 16) | inst2;
+		regs->regs[31] = epc + 6;
+		epc += 4;
+		epc >>= 28;
+		epc <<= 28;
+		/*
+		 * JAL:5 X:1 TARGET[20-16]:5 TARGET[25:21]:5 TARGET[15:0]:16
+		 *
+		 * ......TARGET[15:0].................TARGET[20:16]...........
+		 * ......TARGET[25:21]
+		 */
+		epc |=
+		    ((fullinst & 0xffff) << 2) | ((fullinst & 0x3e00000) >> 3) |
+		    ((fullinst & 0x1f0000) << 7);
+		if (!inst.jal.x)
+			set_isa16_mode(epc);	/* Set ISA mode bit. */
+		regs->cp0_epc = epc;
+		return 0;
+
+		/*
+		 *  J(AL)R(C)
+		 */
+	case MIPS16e_rr_op:
+		if (inst.rr.func == MIPS16e_jr_func) {
+
+			if (inst.rr.ra)
+				regs->cp0_epc = regs->regs[31];
+			else
+				regs->cp0_epc =
+				    regs->regs[reg16to32[inst.rr.rx]];
+
+			if (inst.rr.l) {
+				if (inst.rr.nd)
+					regs->regs[31] = epc + 2;
+				else
+					regs->regs[31] = epc + 4;
+			}
+			return 0;
+		}
+		break;
+	}
+
+	/*
+	 * All other cases have no branch delay slot and are 16-bits.
+	 * Branches do not cause an exception.
+	 */
+	regs->cp0_epc += 2;
+
+	return 0;
+}
+
+/**
+ * __compute_return_epc_for_insn - Computes the return address and do emulate
+ *				    branch simulation, if required.
+ *
+ * @regs:	Pointer to pt_regs
+ * @insn:	branch instruction to decode
+ * Return:	-EFAULT on error and forces SIGILL, and on success
+ *		returns 0 or BRANCH_LIKELY_TAKEN as appropriate after
+ *		evaluating the branch.
+ *
+ * MIPS R6 Compact branches and forbidden slots:
+ *	Compact branches do not throw exceptions because they do
+ *	not have delay slots. The forbidden slot instruction ($PC+4)
+ *	is only executed if the branch was not taken. Otherwise the
+ *	forbidden slot is skipped entirely. This means that the
+ *	only possible reason to be here because of a MIPS R6 compact
+ *	branch instruction is that the forbidden slot has thrown one.
+ *	In that case the branch was not taken, so the EPC can be safely
+ *	set to EPC + 8.
+ */
+int __compute_return_epc_for_insn(struct pt_regs *regs,
+				   union mips_instruction insn)
+{
+	long epc = regs->cp0_epc;
+	unsigned int dspcontrol;
+	int ret = 0;
+
+	switch (insn.i_format.opcode) {
+	/*
+	 * jr and jalr are in r_format format.
+	 */
+	case spec_op:
+		switch (insn.r_format.func) {
+		case jalr_op:
+			regs->regs[insn.r_format.rd] = epc + 8;
+			fallthrough;
+		case jr_op:
+			if (NO_R6EMU && insn.r_format.func == jr_op)
+				goto sigill_r2r6;
+			regs->cp0_epc = regs->regs[insn.r_format.rs];
+			break;
+		}
+		break;
+
+	/*
+	 * This group contains:
+	 * bltz_op, bgez_op, bltzl_op, bgezl_op,
+	 * bltzal_op, bgezal_op, bltzall_op, bgezall_op.
+	 */
+	case bcond_op:
+		switch (insn.i_format.rt) {
+		case bltzl_op:
+			if (NO_R6EMU)
+				goto sigill_r2r6;
+			fallthrough;
+		case bltz_op:
+			if ((long)regs->regs[insn.i_format.rs] < 0) {
+				epc = epc + 4 + (insn.i_format.simmediate << 2);
+				if (insn.i_format.rt == bltzl_op)
+					ret = BRANCH_LIKELY_TAKEN;
+			} else
+				epc += 8;
+			regs->cp0_epc = epc;
+			break;
+
+		case bgezl_op:
+			if (NO_R6EMU)
+				goto sigill_r2r6;
+			fallthrough;
+		case bgez_op:
+			if ((long)regs->regs[insn.i_format.rs] >= 0) {
+				epc = epc + 4 + (insn.i_format.simmediate << 2);
+				if (insn.i_format.rt == bgezl_op)
+					ret = BRANCH_LIKELY_TAKEN;
+			} else
+				epc += 8;
+			regs->cp0_epc = epc;
+			break;
+
+		case bltzal_op:
+		case bltzall_op:
+			if (NO_R6EMU && (insn.i_format.rs ||
+			    insn.i_format.rt == bltzall_op))
+				goto sigill_r2r6;
+			regs->regs[31] = epc + 8;
+			/*
+			 * OK we are here either because we hit a NAL
+			 * instruction or because we are emulating an
+			 * old bltzal{,l} one. Let's figure out what the
+			 * case really is.
+			 */
+			if (!insn.i_format.rs) {
+				/*
+				 * NAL or BLTZAL with rs == 0
+				 * Doesn't matter if we are R6 or not. The
+				 * result is the same
+				 */
+				regs->cp0_epc += 4 +
+					(insn.i_format.simmediate << 2);
+				break;
+			}
+			/* Now do the real thing for non-R6 BLTZAL{,L} */
+			if ((long)regs->regs[insn.i_format.rs] < 0) {
+				epc = epc + 4 + (insn.i_format.simmediate << 2);
+				if (insn.i_format.rt == bltzall_op)
+					ret = BRANCH_LIKELY_TAKEN;
+			} else
+				epc += 8;
+			regs->cp0_epc = epc;
+			break;
+
+		case bgezal_op:
+		case bgezall_op:
+			if (NO_R6EMU && (insn.i_format.rs ||
+			    insn.i_format.rt == bgezall_op))
+				goto sigill_r2r6;
+			regs->regs[31] = epc + 8;
+			/*
+			 * OK we are here either because we hit a BAL
+			 * instruction or because we are emulating an
+			 * old bgezal{,l} one. Let's figure out what the
+			 * case really is.
+			 */
+			if (!insn.i_format.rs) {
+				/*
+				 * BAL or BGEZAL with rs == 0
+				 * Doesn't matter if we are R6 or not. The
+				 * result is the same
+				 */
+				regs->cp0_epc += 4 +
+					(insn.i_format.simmediate << 2);
+				break;
+			}
+			/* Now do the real thing for non-R6 BGEZAL{,L} */
+			if ((long)regs->regs[insn.i_format.rs] >= 0) {
+				epc = epc + 4 + (insn.i_format.simmediate << 2);
+				if (insn.i_format.rt == bgezall_op)
+					ret = BRANCH_LIKELY_TAKEN;
+			} else
+				epc += 8;
+			regs->cp0_epc = epc;
+			break;
+
+		case bposge32_op:
+			if (!cpu_has_dsp)
+				goto sigill_dsp;
+
+			dspcontrol = rddsp(0x01);
+
+			if (dspcontrol >= 32) {
+				epc = epc + 4 + (insn.i_format.simmediate << 2);
+			} else
+				epc += 8;
+			regs->cp0_epc = epc;
+			break;
+		}
+		break;
+
+	/*
+	 * These are unconditional and in j_format.
+	 */
+	case jalx_op:
+	case jal_op:
+		regs->regs[31] = regs->cp0_epc + 8;
+		fallthrough;
+	case j_op:
+		epc += 4;
+		epc >>= 28;
+		epc <<= 28;
+		epc |= (insn.j_format.target << 2);
+		regs->cp0_epc = epc;
+		if (insn.i_format.opcode == jalx_op)
+			set_isa16_mode(regs->cp0_epc);
+		break;
+
+	/*
+	 * These are conditional and in i_format.
+	 */
+	case beql_op:
+		if (NO_R6EMU)
+			goto sigill_r2r6;
+		fallthrough;
+	case beq_op:
+		if (regs->regs[insn.i_format.rs] ==
+		    regs->regs[insn.i_format.rt]) {
+			epc = epc + 4 + (insn.i_format.simmediate << 2);
+			if (insn.i_format.opcode == beql_op)
+				ret = BRANCH_LIKELY_TAKEN;
+		} else
+			epc += 8;
+		regs->cp0_epc = epc;
+		break;
+
+	case bnel_op:
+		if (NO_R6EMU)
+			goto sigill_r2r6;
+		fallthrough;
+	case bne_op:
+		if (regs->regs[insn.i_format.rs] !=
+		    regs->regs[insn.i_format.rt]) {
+			epc = epc + 4 + (insn.i_format.simmediate << 2);
+			if (insn.i_format.opcode == bnel_op)
+				ret = BRANCH_LIKELY_TAKEN;
+		} else
+			epc += 8;
+		regs->cp0_epc = epc;
+		break;
+
+	case blezl_op: /* not really i_format */
+		if (!insn.i_format.rt && NO_R6EMU)
+			goto sigill_r2r6;
+		fallthrough;
+	case blez_op:
+		/*
+		 * Compact branches for R6 for the
+		 * blez and blezl opcodes.
+		 * BLEZ  | rs = 0 | rt != 0  == BLEZALC
+		 * BLEZ  | rs = rt != 0      == BGEZALC
+		 * BLEZ  | rs != 0 | rt != 0 == BGEUC
+		 * BLEZL | rs = 0 | rt != 0  == BLEZC
+		 * BLEZL | rs = rt != 0      == BGEZC
+		 * BLEZL | rs != 0 | rt != 0 == BGEC
+		 *
+		 * For real BLEZ{,L}, rt is always 0.
+		 */
+
+		if (cpu_has_mips_r6 && insn.i_format.rt) {
+			if ((insn.i_format.opcode == blez_op) &&
+			    ((!insn.i_format.rs && insn.i_format.rt) ||
+			     (insn.i_format.rs == insn.i_format.rt)))
+				regs->regs[31] = epc + 4;
+			regs->cp0_epc += 8;
+			break;
+		}
+		/* rt field assumed to be zero */
+		if ((long)regs->regs[insn.i_format.rs] <= 0) {
+			epc = epc + 4 + (insn.i_format.simmediate << 2);
+			if (insn.i_format.opcode == blezl_op)
+				ret = BRANCH_LIKELY_TAKEN;
+		} else
+			epc += 8;
+		regs->cp0_epc = epc;
+		break;
+
+	case bgtzl_op:
+		if (!insn.i_format.rt && NO_R6EMU)
+			goto sigill_r2r6;
+		fallthrough;
+	case bgtz_op:
+		/*
+		 * Compact branches for R6 for the
+		 * bgtz and bgtzl opcodes.
+		 * BGTZ  | rs = 0 | rt != 0  == BGTZALC
+		 * BGTZ  | rs = rt != 0      == BLTZALC
+		 * BGTZ  | rs != 0 | rt != 0 == BLTUC
+		 * BGTZL | rs = 0 | rt != 0  == BGTZC
+		 * BGTZL | rs = rt != 0      == BLTZC
+		 * BGTZL | rs != 0 | rt != 0 == BLTC
+		 *
+		 * *ZALC varint for BGTZ &&& rt != 0
+		 * For real GTZ{,L}, rt is always 0.
+		 */
+		if (cpu_has_mips_r6 && insn.i_format.rt) {
+			if ((insn.i_format.opcode == blez_op) &&
+			    ((!insn.i_format.rs && insn.i_format.rt) ||
+			    (insn.i_format.rs == insn.i_format.rt)))
+				regs->regs[31] = epc + 4;
+			regs->cp0_epc += 8;
+			break;
+		}
+
+		/* rt field assumed to be zero */
+		if ((long)regs->regs[insn.i_format.rs] > 0) {
+			epc = epc + 4 + (insn.i_format.simmediate << 2);
+			if (insn.i_format.opcode == bgtzl_op)
+				ret = BRANCH_LIKELY_TAKEN;
+		} else
+			epc += 8;
+		regs->cp0_epc = epc;
+		break;
+
+#ifdef CONFIG_MIPS_FP_SUPPORT
+	/*
+	 * And now the FPA/cp1 branch instructions.
+	 */
+	case cop1_op: {
+		unsigned int bit, fcr31, reg;
+
+		if (cpu_has_mips_r6 &&
+		    ((insn.i_format.rs == bc1eqz_op) ||
+		     (insn.i_format.rs == bc1nez_op))) {
+			if (!init_fp_ctx(current))
+				lose_fpu(1);
+			reg = insn.i_format.rt;
+			bit = get_fpr32(&current->thread.fpu.fpr[reg], 0) & 0x1;
+			if (insn.i_format.rs == bc1eqz_op)
+				bit = !bit;
+			own_fpu(1);
+			if (bit)
+				epc = epc + 4 +
+					(insn.i_format.simmediate << 2);
+			else
+				epc += 8;
+			regs->cp0_epc = epc;
+
+			break;
+		} else {
+
+			preempt_disable();
+			if (is_fpu_owner())
+			        fcr31 = read_32bit_cp1_register(CP1_STATUS);
+			else
+				fcr31 = current->thread.fpu.fcr31;
+			preempt_enable();
+
+			bit = (insn.i_format.rt >> 2);
+			bit += (bit != 0);
+			bit += 23;
+			switch (insn.i_format.rt & 3) {
+			case 0: /* bc1f */
+			case 2: /* bc1fl */
+				if (~fcr31 & (1 << bit)) {
+					epc = epc + 4 +
+						(insn.i_format.simmediate << 2);
+					if (insn.i_format.rt == 2)
+						ret = BRANCH_LIKELY_TAKEN;
+				} else
+					epc += 8;
+				regs->cp0_epc = epc;
+				break;
+
+			case 1: /* bc1t */
+			case 3: /* bc1tl */
+				if (fcr31 & (1 << bit)) {
+					epc = epc + 4 +
+						(insn.i_format.simmediate << 2);
+					if (insn.i_format.rt == 3)
+						ret = BRANCH_LIKELY_TAKEN;
+				} else
+					epc += 8;
+				regs->cp0_epc = epc;
+				break;
+			}
+			break;
+		}
+	}
+#endif /* CONFIG_MIPS_FP_SUPPORT */
+
+#ifdef CONFIG_CPU_CAVIUM_OCTEON
+	case lwc2_op: /* This is bbit0 on Octeon */
+		if ((regs->regs[insn.i_format.rs] & (1ull<<insn.i_format.rt))
+		     == 0)
+			epc = epc + 4 + (insn.i_format.simmediate << 2);
+		else
+			epc += 8;
+		regs->cp0_epc = epc;
+		break;
+	case ldc2_op: /* This is bbit032 on Octeon */
+		if ((regs->regs[insn.i_format.rs] &
+		    (1ull<<(insn.i_format.rt+32))) == 0)
+			epc = epc + 4 + (insn.i_format.simmediate << 2);
+		else
+			epc += 8;
+		regs->cp0_epc = epc;
+		break;
+	case swc2_op: /* This is bbit1 on Octeon */
+		if (regs->regs[insn.i_format.rs] & (1ull<<insn.i_format.rt))
+			epc = epc + 4 + (insn.i_format.simmediate << 2);
+		else
+			epc += 8;
+		regs->cp0_epc = epc;
+		break;
+	case sdc2_op: /* This is bbit132 on Octeon */
+		if (regs->regs[insn.i_format.rs] &
+		    (1ull<<(insn.i_format.rt+32)))
+			epc = epc + 4 + (insn.i_format.simmediate << 2);
+		else
+			epc += 8;
+		regs->cp0_epc = epc;
+		break;
+#else
+	case bc6_op:
+		/* Only valid for MIPS R6 */
+		if (!cpu_has_mips_r6)
+			goto sigill_r6;
+		regs->cp0_epc += 8;
+		break;
+	case balc6_op:
+		if (!cpu_has_mips_r6)
+			goto sigill_r6;
+		/* Compact branch: BALC */
+		regs->regs[31] = epc + 4;
+		epc += 4 + (insn.i_format.simmediate << 2);
+		regs->cp0_epc = epc;
+		break;
+	case pop66_op:
+		if (!cpu_has_mips_r6)
+			goto sigill_r6;
+		/* Compact branch: BEQZC || JIC */
+		regs->cp0_epc += 8;
+		break;
+	case pop76_op:
+		if (!cpu_has_mips_r6)
+			goto sigill_r6;
+		/* Compact branch: BNEZC || JIALC */
+		if (!insn.i_format.rs) {
+			/* JIALC: set $31/ra */
+			regs->regs[31] = epc + 4;
+		}
+		regs->cp0_epc += 8;
+		break;
+#endif
+	case pop10_op:
+	case pop30_op:
+		/* Only valid for MIPS R6 */
+		if (!cpu_has_mips_r6)
+			goto sigill_r6;
+		/*
+		 * Compact branches:
+		 * bovc, beqc, beqzalc, bnvc, bnec, bnezlac
+		 */
+		if (insn.i_format.rt && !insn.i_format.rs)
+			regs->regs[31] = epc + 4;
+		regs->cp0_epc += 8;
+		break;
+	}
+
+	return ret;
+
+sigill_dsp:
+	pr_debug("%s: DSP branch but not DSP ASE - sending SIGILL.\n",
+		 current->comm);
+	force_sig(SIGILL);
+	return -EFAULT;
+sigill_r2r6:
+	pr_debug("%s: R2 branch but r2-to-r6 emulator is not present - sending SIGILL.\n",
+		 current->comm);
+	force_sig(SIGILL);
+	return -EFAULT;
+sigill_r6:
+	pr_debug("%s: R6 branch but no MIPSr6 ISA support - sending SIGILL.\n",
+		 current->comm);
+	force_sig(SIGILL);
+	return -EFAULT;
+}
+EXPORT_SYMBOL_GPL(__compute_return_epc_for_insn);
+
+int __compute_return_epc(struct pt_regs *regs)
+{
+	unsigned int __user *addr;
+	long epc;
+	union mips_instruction insn;
+
+	epc = regs->cp0_epc;
+	if (epc & 3)
+		goto unaligned;
+
+	/*
+	 * Read the instruction
+	 */
+	addr = (unsigned int __user *) epc;
+	if (__get_user(insn.word, addr)) {
+		force_sig(SIGSEGV);
+		return -EFAULT;
+	}
+
+	return __compute_return_epc_for_insn(regs, insn);
+
+unaligned:
+	printk("%s: unaligned epc - sending SIGBUS.\n", current->comm);
+	force_sig(SIGBUS);
+	return -EFAULT;
+}
+
+#if (defined CONFIG_KPROBES) || (defined CONFIG_UPROBES)
+
+int __insn_is_compact_branch(union mips_instruction insn)
+{
+	if (!cpu_has_mips_r6)
+		return 0;
+
+	switch (insn.i_format.opcode) {
+	case blezl_op:
+	case bgtzl_op:
+	case blez_op:
+	case bgtz_op:
+		/*
+		 * blez[l] and bgtz[l] opcodes with non-zero rt
+		 * are MIPS R6 compact branches
+		 */
+		if (insn.i_format.rt)
+			return 1;
+		break;
+	case bc6_op:
+	case balc6_op:
+	case pop10_op:
+	case pop30_op:
+	case pop66_op:
+	case pop76_op:
+		return 1;
+	}
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(__insn_is_compact_branch);
+
+#endif  /* CONFIG_KPROBES || CONFIG_UPROBES */
diff --git a/arch/mips/kernel/cacheinfo.c b/arch/mips/kernel/cacheinfo.c
new file mode 100644
index 000000000..495dd0582
--- /dev/null
+++ b/arch/mips/kernel/cacheinfo.c
@@ -0,0 +1,116 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * MIPS cacheinfo support
+ */
+#include <linux/cacheinfo.h>
+
+/* Populates leaf and increments to next leaf */
+#define populate_cache(cache, leaf, c_level, c_type)		\
+do {								\
+	leaf->type = c_type;					\
+	leaf->level = c_level;					\
+	leaf->coherency_line_size = c->cache.linesz;		\
+	leaf->number_of_sets = c->cache.sets;			\
+	leaf->ways_of_associativity = c->cache.ways;		\
+	leaf->size = c->cache.linesz * c->cache.sets *		\
+		c->cache.ways;					\
+	leaf++;							\
+} while (0)
+
+int init_cache_level(unsigned int cpu)
+{
+	struct cpuinfo_mips *c = &current_cpu_data;
+	struct cpu_cacheinfo *this_cpu_ci = get_cpu_cacheinfo(cpu);
+	int levels = 0, leaves = 0;
+
+	/*
+	 * If Dcache is not set, we assume the cache structures
+	 * are not properly initialized.
+	 */
+	if (c->dcache.waysize)
+		levels += 1;
+	else
+		return -ENOENT;
+
+
+	leaves += (c->icache.waysize) ? 2 : 1;
+
+	if (c->vcache.waysize) {
+		levels++;
+		leaves++;
+	}
+
+	if (c->scache.waysize) {
+		levels++;
+		leaves++;
+	}
+
+	if (c->tcache.waysize) {
+		levels++;
+		leaves++;
+	}
+
+	this_cpu_ci->num_levels = levels;
+	this_cpu_ci->num_leaves = leaves;
+	return 0;
+}
+
+static void fill_cpumask_siblings(int cpu, cpumask_t *cpu_map)
+{
+	int cpu1;
+
+	for_each_possible_cpu(cpu1)
+		if (cpus_are_siblings(cpu, cpu1))
+			cpumask_set_cpu(cpu1, cpu_map);
+}
+
+static void fill_cpumask_cluster(int cpu, cpumask_t *cpu_map)
+{
+	int cpu1;
+	int cluster = cpu_cluster(&cpu_data[cpu]);
+
+	for_each_possible_cpu(cpu1)
+		if (cpu_cluster(&cpu_data[cpu1]) == cluster)
+			cpumask_set_cpu(cpu1, cpu_map);
+}
+
+int populate_cache_leaves(unsigned int cpu)
+{
+	struct cpuinfo_mips *c = &current_cpu_data;
+	struct cpu_cacheinfo *this_cpu_ci = get_cpu_cacheinfo(cpu);
+	struct cacheinfo *this_leaf = this_cpu_ci->info_list;
+	int level = 1;
+
+	if (c->icache.waysize) {
+		/* I/D caches are per core */
+		fill_cpumask_siblings(cpu, &this_leaf->shared_cpu_map);
+		populate_cache(dcache, this_leaf, level, CACHE_TYPE_DATA);
+		fill_cpumask_siblings(cpu, &this_leaf->shared_cpu_map);
+		populate_cache(icache, this_leaf, level, CACHE_TYPE_INST);
+		level++;
+	} else {
+		populate_cache(dcache, this_leaf, level, CACHE_TYPE_UNIFIED);
+		level++;
+	}
+
+	if (c->vcache.waysize) {
+		/* Vcache is per core as well */
+		fill_cpumask_siblings(cpu, &this_leaf->shared_cpu_map);
+		populate_cache(vcache, this_leaf, level, CACHE_TYPE_UNIFIED);
+		level++;
+	}
+
+	if (c->scache.waysize) {
+		/* Scache is per cluster */
+		fill_cpumask_cluster(cpu, &this_leaf->shared_cpu_map);
+		populate_cache(scache, this_leaf, level, CACHE_TYPE_UNIFIED);
+		level++;
+	}
+
+	if (c->tcache.waysize)
+		populate_cache(tcache, this_leaf, level, CACHE_TYPE_UNIFIED);
+
+	this_cpu_ci->cpu_map_populated = true;
+
+	return 0;
+}
diff --git a/arch/mips/kernel/cevt-bcm1480.c b/arch/mips/kernel/cevt-bcm1480.c
new file mode 100644
index 000000000..d39a2963b
--- /dev/null
+++ b/arch/mips/kernel/cevt-bcm1480.c
@@ -0,0 +1,138 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2000,2001,2004 Broadcom Corporation
+ */
+#include <linux/clockchips.h>
+#include <linux/interrupt.h>
+#include <linux/percpu.h>
+#include <linux/smp.h>
+#include <linux/irq.h>
+
+#include <asm/addrspace.h>
+#include <asm/io.h>
+#include <asm/time.h>
+
+#include <asm/sibyte/bcm1480_regs.h>
+#include <asm/sibyte/sb1250_regs.h>
+#include <asm/sibyte/bcm1480_int.h>
+#include <asm/sibyte/bcm1480_scd.h>
+
+#include <asm/sibyte/sb1250.h>
+
+#define IMR_IP2_VAL	K_BCM1480_INT_MAP_I0
+#define IMR_IP3_VAL	K_BCM1480_INT_MAP_I1
+#define IMR_IP4_VAL	K_BCM1480_INT_MAP_I2
+
+/*
+ * The general purpose timer ticks at 1MHz independent if
+ * the rest of the system
+ */
+
+static int sibyte_set_periodic(struct clock_event_device *evt)
+{
+	unsigned int cpu = smp_processor_id();
+	void __iomem *cfg, *init;
+
+	cfg = IOADDR(A_SCD_TIMER_REGISTER(cpu, R_SCD_TIMER_CFG));
+	init = IOADDR(A_SCD_TIMER_REGISTER(cpu, R_SCD_TIMER_INIT));
+
+	__raw_writeq(0, cfg);
+	__raw_writeq((V_SCD_TIMER_FREQ / HZ) - 1, init);
+	__raw_writeq(M_SCD_TIMER_ENABLE | M_SCD_TIMER_MODE_CONTINUOUS, cfg);
+	return 0;
+}
+
+static int sibyte_shutdown(struct clock_event_device *evt)
+{
+	unsigned int cpu = smp_processor_id();
+	void __iomem *cfg;
+
+	cfg = IOADDR(A_SCD_TIMER_REGISTER(cpu, R_SCD_TIMER_CFG));
+
+	/* Stop the timer until we actually program a shot */
+	__raw_writeq(0, cfg);
+	return 0;
+}
+
+static int sibyte_next_event(unsigned long delta, struct clock_event_device *cd)
+{
+	unsigned int cpu = smp_processor_id();
+	void __iomem *cfg, *init;
+
+	cfg = IOADDR(A_SCD_TIMER_REGISTER(cpu, R_SCD_TIMER_CFG));
+	init = IOADDR(A_SCD_TIMER_REGISTER(cpu, R_SCD_TIMER_INIT));
+
+	__raw_writeq(0, cfg);
+	__raw_writeq(delta - 1, init);
+	__raw_writeq(M_SCD_TIMER_ENABLE, cfg);
+
+	return 0;
+}
+
+static irqreturn_t sibyte_counter_handler(int irq, void *dev_id)
+{
+	unsigned int cpu = smp_processor_id();
+	struct clock_event_device *cd = dev_id;
+	void __iomem *cfg;
+	unsigned long tmode;
+
+	if (clockevent_state_periodic(cd))
+		tmode = M_SCD_TIMER_ENABLE | M_SCD_TIMER_MODE_CONTINUOUS;
+	else
+		tmode = 0;
+
+	/* ACK interrupt */
+	cfg = IOADDR(A_SCD_TIMER_REGISTER(cpu, R_SCD_TIMER_CFG));
+	____raw_writeq(tmode, cfg);
+
+	cd->event_handler(cd);
+
+	return IRQ_HANDLED;
+}
+
+static DEFINE_PER_CPU(struct clock_event_device, sibyte_hpt_clockevent);
+static DEFINE_PER_CPU(char [18], sibyte_hpt_name);
+
+void sb1480_clockevent_init(void)
+{
+	unsigned int cpu = smp_processor_id();
+	unsigned int irq = K_BCM1480_INT_TIMER_0 + cpu;
+	struct clock_event_device *cd = &per_cpu(sibyte_hpt_clockevent, cpu);
+	unsigned char *name = per_cpu(sibyte_hpt_name, cpu);
+	unsigned long flags =  IRQF_PERCPU | IRQF_TIMER;
+
+	BUG_ON(cpu > 3);	/* Only have 4 general purpose timers */
+
+	sprintf(name, "bcm1480-counter-%d", cpu);
+	cd->name		= name;
+	cd->features		= CLOCK_EVT_FEAT_PERIODIC |
+				  CLOCK_EVT_FEAT_ONESHOT;
+	clockevent_set_clock(cd, V_SCD_TIMER_FREQ);
+	cd->max_delta_ns	= clockevent_delta2ns(0x7fffff, cd);
+	cd->max_delta_ticks	= 0x7fffff;
+	cd->min_delta_ns	= clockevent_delta2ns(2, cd);
+	cd->min_delta_ticks	= 2;
+	cd->rating		= 200;
+	cd->irq			= irq;
+	cd->cpumask		= cpumask_of(cpu);
+	cd->set_next_event	= sibyte_next_event;
+	cd->set_state_shutdown	= sibyte_shutdown;
+	cd->set_state_periodic	= sibyte_set_periodic;
+	cd->set_state_oneshot	= sibyte_shutdown;
+	clockevents_register_device(cd);
+
+	bcm1480_mask_irq(cpu, irq);
+
+	/*
+	 * Map the timer interrupt to IP[4] of this cpu
+	 */
+	__raw_writeq(IMR_IP4_VAL,
+		     IOADDR(A_BCM1480_IMR_REGISTER(cpu,
+			R_BCM1480_IMR_INTERRUPT_MAP_BASE_H) + (irq << 3)));
+
+	bcm1480_unmask_irq(cpu, irq);
+
+	irq_set_affinity(irq, cpumask_of(cpu));
+	if (request_irq(irq, sibyte_counter_handler, flags, name, cd))
+		pr_err("Failed to request irq %d (%s)\n", irq, name);
+}
diff --git a/arch/mips/kernel/cevt-ds1287.c b/arch/mips/kernel/cevt-ds1287.c
new file mode 100644
index 000000000..9a47fbcd4
--- /dev/null
+++ b/arch/mips/kernel/cevt-ds1287.c
@@ -0,0 +1,121 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *  DS1287 clockevent driver
+ *
+ *  Copyright (C) 2008	Yoichi Yuasa <yuasa@linux-mips.org>
+ */
+#include <linux/clockchips.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/mc146818rtc.h>
+#include <linux/irq.h>
+
+#include <asm/time.h>
+
+int ds1287_timer_state(void)
+{
+	return (CMOS_READ(RTC_REG_C) & RTC_PF) != 0;
+}
+
+int ds1287_set_base_clock(unsigned int hz)
+{
+	u8 rate;
+
+	switch (hz) {
+	case 128:
+		rate = 0x9;
+		break;
+	case 256:
+		rate = 0x8;
+		break;
+	case 1024:
+		rate = 0x6;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	CMOS_WRITE(RTC_REF_CLCK_32KHZ | rate, RTC_REG_A);
+
+	return 0;
+}
+
+static int ds1287_set_next_event(unsigned long delta,
+				 struct clock_event_device *evt)
+{
+	return -EINVAL;
+}
+
+static int ds1287_shutdown(struct clock_event_device *evt)
+{
+	u8 val;
+
+	spin_lock(&rtc_lock);
+
+	val = CMOS_READ(RTC_REG_B);
+	val &= ~RTC_PIE;
+	CMOS_WRITE(val, RTC_REG_B);
+
+	spin_unlock(&rtc_lock);
+	return 0;
+}
+
+static int ds1287_set_periodic(struct clock_event_device *evt)
+{
+	u8 val;
+
+	spin_lock(&rtc_lock);
+
+	val = CMOS_READ(RTC_REG_B);
+	val |= RTC_PIE;
+	CMOS_WRITE(val, RTC_REG_B);
+
+	spin_unlock(&rtc_lock);
+	return 0;
+}
+
+static void ds1287_event_handler(struct clock_event_device *dev)
+{
+}
+
+static struct clock_event_device ds1287_clockevent = {
+	.name			= "ds1287",
+	.features		= CLOCK_EVT_FEAT_PERIODIC,
+	.set_next_event		= ds1287_set_next_event,
+	.set_state_shutdown	= ds1287_shutdown,
+	.set_state_periodic	= ds1287_set_periodic,
+	.tick_resume		= ds1287_shutdown,
+	.event_handler		= ds1287_event_handler,
+};
+
+static irqreturn_t ds1287_interrupt(int irq, void *dev_id)
+{
+	struct clock_event_device *cd = &ds1287_clockevent;
+
+	/* Ack the RTC interrupt. */
+	CMOS_READ(RTC_REG_C);
+
+	cd->event_handler(cd);
+
+	return IRQ_HANDLED;
+}
+
+int __init ds1287_clockevent_init(int irq)
+{
+	unsigned long flags = IRQF_PERCPU | IRQF_TIMER;
+	struct clock_event_device *cd;
+
+	cd = &ds1287_clockevent;
+	cd->rating = 100;
+	cd->irq = irq;
+	clockevent_set_clock(cd, 32768);
+	cd->max_delta_ns = clockevent_delta2ns(0x7fffffff, cd);
+	cd->max_delta_ticks = 0x7fffffff;
+	cd->min_delta_ns = clockevent_delta2ns(0x300, cd);
+	cd->min_delta_ticks = 0x300;
+	cd->cpumask = cpumask_of(0);
+
+	clockevents_register_device(&ds1287_clockevent);
+
+	return request_irq(irq, ds1287_interrupt, flags, "ds1287", NULL);
+}
diff --git a/arch/mips/kernel/cevt-gt641xx.c b/arch/mips/kernel/cevt-gt641xx.c
new file mode 100644
index 000000000..5b132e8c5
--- /dev/null
+++ b/arch/mips/kernel/cevt-gt641xx.c
@@ -0,0 +1,146 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *  GT641xx clockevent routines.
+ *
+ *  Copyright (C) 2007	Yoichi Yuasa <yuasa@linux-mips.org>
+ */
+#include <linux/clockchips.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/spinlock.h>
+#include <linux/irq.h>
+
+#include <asm/gt64120.h>
+#include <asm/time.h>
+
+static DEFINE_RAW_SPINLOCK(gt641xx_timer_lock);
+static unsigned int gt641xx_base_clock;
+
+void gt641xx_set_base_clock(unsigned int clock)
+{
+	gt641xx_base_clock = clock;
+}
+
+int gt641xx_timer0_state(void)
+{
+	if (GT_READ(GT_TC0_OFS))
+		return 0;
+
+	GT_WRITE(GT_TC0_OFS, gt641xx_base_clock / HZ);
+	GT_WRITE(GT_TC_CONTROL_OFS, GT_TC_CONTROL_ENTC0_MSK);
+
+	return 1;
+}
+
+static int gt641xx_timer0_set_next_event(unsigned long delta,
+					 struct clock_event_device *evt)
+{
+	u32 ctrl;
+
+	raw_spin_lock(&gt641xx_timer_lock);
+
+	ctrl = GT_READ(GT_TC_CONTROL_OFS);
+	ctrl &= ~(GT_TC_CONTROL_ENTC0_MSK | GT_TC_CONTROL_SELTC0_MSK);
+	ctrl |= GT_TC_CONTROL_ENTC0_MSK;
+
+	GT_WRITE(GT_TC0_OFS, delta);
+	GT_WRITE(GT_TC_CONTROL_OFS, ctrl);
+
+	raw_spin_unlock(&gt641xx_timer_lock);
+
+	return 0;
+}
+
+static int gt641xx_timer0_shutdown(struct clock_event_device *evt)
+{
+	u32 ctrl;
+
+	raw_spin_lock(&gt641xx_timer_lock);
+
+	ctrl = GT_READ(GT_TC_CONTROL_OFS);
+	ctrl &= ~(GT_TC_CONTROL_ENTC0_MSK | GT_TC_CONTROL_SELTC0_MSK);
+	GT_WRITE(GT_TC_CONTROL_OFS, ctrl);
+
+	raw_spin_unlock(&gt641xx_timer_lock);
+	return 0;
+}
+
+static int gt641xx_timer0_set_oneshot(struct clock_event_device *evt)
+{
+	u32 ctrl;
+
+	raw_spin_lock(&gt641xx_timer_lock);
+
+	ctrl = GT_READ(GT_TC_CONTROL_OFS);
+	ctrl &= ~GT_TC_CONTROL_SELTC0_MSK;
+	ctrl |= GT_TC_CONTROL_ENTC0_MSK;
+	GT_WRITE(GT_TC_CONTROL_OFS, ctrl);
+
+	raw_spin_unlock(&gt641xx_timer_lock);
+	return 0;
+}
+
+static int gt641xx_timer0_set_periodic(struct clock_event_device *evt)
+{
+	u32 ctrl;
+
+	raw_spin_lock(&gt641xx_timer_lock);
+
+	ctrl = GT_READ(GT_TC_CONTROL_OFS);
+	ctrl |= GT_TC_CONTROL_ENTC0_MSK | GT_TC_CONTROL_SELTC0_MSK;
+	GT_WRITE(GT_TC_CONTROL_OFS, ctrl);
+
+	raw_spin_unlock(&gt641xx_timer_lock);
+	return 0;
+}
+
+static void gt641xx_timer0_event_handler(struct clock_event_device *dev)
+{
+}
+
+static struct clock_event_device gt641xx_timer0_clockevent = {
+	.name			= "gt641xx-timer0",
+	.features		= CLOCK_EVT_FEAT_PERIODIC |
+				  CLOCK_EVT_FEAT_ONESHOT,
+	.irq			= GT641XX_TIMER0_IRQ,
+	.set_next_event		= gt641xx_timer0_set_next_event,
+	.set_state_shutdown	= gt641xx_timer0_shutdown,
+	.set_state_periodic	= gt641xx_timer0_set_periodic,
+	.set_state_oneshot	= gt641xx_timer0_set_oneshot,
+	.tick_resume		= gt641xx_timer0_shutdown,
+	.event_handler		= gt641xx_timer0_event_handler,
+};
+
+static irqreturn_t gt641xx_timer0_interrupt(int irq, void *dev_id)
+{
+	struct clock_event_device *cd = &gt641xx_timer0_clockevent;
+
+	cd->event_handler(cd);
+
+	return IRQ_HANDLED;
+}
+
+static int __init gt641xx_timer0_clockevent_init(void)
+{
+	struct clock_event_device *cd;
+
+	if (!gt641xx_base_clock)
+		return 0;
+
+	GT_WRITE(GT_TC0_OFS, gt641xx_base_clock / HZ);
+
+	cd = &gt641xx_timer0_clockevent;
+	cd->rating = 200 + gt641xx_base_clock / 10000000;
+	clockevent_set_clock(cd, gt641xx_base_clock);
+	cd->max_delta_ns = clockevent_delta2ns(0x7fffffff, cd);
+	cd->max_delta_ticks = 0x7fffffff;
+	cd->min_delta_ns = clockevent_delta2ns(0x300, cd);
+	cd->min_delta_ticks = 0x300;
+	cd->cpumask = cpumask_of(0);
+
+	clockevents_register_device(&gt641xx_timer0_clockevent);
+
+	return request_irq(GT641XX_TIMER0_IRQ, gt641xx_timer0_interrupt,
+			   IRQF_PERCPU | IRQF_TIMER, "gt641xx_timer0", NULL);
+}
+arch_initcall(gt641xx_timer0_clockevent_init);
diff --git a/arch/mips/kernel/cevt-r4k.c b/arch/mips/kernel/cevt-r4k.c
new file mode 100644
index 000000000..32ec67c9a
--- /dev/null
+++ b/arch/mips/kernel/cevt-r4k.c
@@ -0,0 +1,341 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2007 MIPS Technologies, Inc.
+ * Copyright (C) 2007 Ralf Baechle <ralf@linux-mips.org>
+ */
+#include <linux/clockchips.h>
+#include <linux/interrupt.h>
+#include <linux/cpufreq.h>
+#include <linux/percpu.h>
+#include <linux/smp.h>
+#include <linux/irq.h>
+
+#include <asm/time.h>
+#include <asm/cevt-r4k.h>
+
+static int mips_next_event(unsigned long delta,
+			   struct clock_event_device *evt)
+{
+	unsigned int cnt;
+	int res;
+
+	cnt = read_c0_count();
+	cnt += delta;
+	write_c0_compare(cnt);
+	res = ((int)(read_c0_count() - cnt) >= 0) ? -ETIME : 0;
+	return res;
+}
+
+/**
+ * calculate_min_delta() - Calculate a good minimum delta for mips_next_event().
+ *
+ * Running under virtualisation can introduce overhead into mips_next_event() in
+ * the form of hypervisor emulation of CP0_Count/CP0_Compare registers,
+ * potentially with an unnatural frequency, which makes a fixed min_delta_ns
+ * value inappropriate as it may be too small.
+ *
+ * It can also introduce occasional latency from the guest being descheduled.
+ *
+ * This function calculates a good minimum delta based roughly on the 75th
+ * percentile of the time taken to do the mips_next_event() sequence, in order
+ * to handle potentially higher overhead while also eliminating outliers due to
+ * unpredictable hypervisor latency (which can be handled by retries).
+ *
+ * Return:	An appropriate minimum delta for the clock event device.
+ */
+static unsigned int calculate_min_delta(void)
+{
+	unsigned int cnt, i, j, k, l;
+	unsigned int buf1[4], buf2[3];
+	unsigned int min_delta;
+
+	/*
+	 * Calculate the median of 5 75th percentiles of 5 samples of how long
+	 * it takes to set CP0_Compare = CP0_Count + delta.
+	 */
+	for (i = 0; i < 5; ++i) {
+		for (j = 0; j < 5; ++j) {
+			/*
+			 * This is like the code in mips_next_event(), and
+			 * directly measures the borderline "safe" delta.
+			 */
+			cnt = read_c0_count();
+			write_c0_compare(cnt);
+			cnt = read_c0_count() - cnt;
+
+			/* Sorted insert into buf1 */
+			for (k = 0; k < j; ++k) {
+				if (cnt < buf1[k]) {
+					l = min_t(unsigned int,
+						  j, ARRAY_SIZE(buf1) - 1);
+					for (; l > k; --l)
+						buf1[l] = buf1[l - 1];
+					break;
+				}
+			}
+			if (k < ARRAY_SIZE(buf1))
+				buf1[k] = cnt;
+		}
+
+		/* Sorted insert of 75th percentile into buf2 */
+		for (k = 0; k < i && k < ARRAY_SIZE(buf2); ++k) {
+			if (buf1[ARRAY_SIZE(buf1) - 1] < buf2[k]) {
+				l = min_t(unsigned int,
+					  i, ARRAY_SIZE(buf2) - 1);
+				for (; l > k; --l)
+					buf2[l] = buf2[l - 1];
+				break;
+			}
+		}
+		if (k < ARRAY_SIZE(buf2))
+			buf2[k] = buf1[ARRAY_SIZE(buf1) - 1];
+	}
+
+	/* Use 2 * median of 75th percentiles */
+	min_delta = buf2[ARRAY_SIZE(buf2) - 1] * 2;
+
+	/* Don't go too low */
+	if (min_delta < 0x300)
+		min_delta = 0x300;
+
+	pr_debug("%s: median 75th percentile=%#x, min_delta=%#x\n",
+		 __func__, buf2[ARRAY_SIZE(buf2) - 1], min_delta);
+	return min_delta;
+}
+
+DEFINE_PER_CPU(struct clock_event_device, mips_clockevent_device);
+int cp0_timer_irq_installed;
+
+/*
+ * Possibly handle a performance counter interrupt.
+ * Return true if the timer interrupt should not be checked
+ */
+static inline int handle_perf_irq(int r2)
+{
+	/*
+	 * The performance counter overflow interrupt may be shared with the
+	 * timer interrupt (cp0_perfcount_irq < 0). If it is and a
+	 * performance counter has overflowed (perf_irq() == IRQ_HANDLED)
+	 * and we can't reliably determine if a counter interrupt has also
+	 * happened (!r2) then don't check for a timer interrupt.
+	 */
+	return (cp0_perfcount_irq < 0) &&
+		perf_irq() == IRQ_HANDLED &&
+		!r2;
+}
+
+irqreturn_t c0_compare_interrupt(int irq, void *dev_id)
+{
+	const int r2 = cpu_has_mips_r2_r6;
+	struct clock_event_device *cd;
+	int cpu = smp_processor_id();
+
+	/*
+	 * Suckage alert:
+	 * Before R2 of the architecture there was no way to see if a
+	 * performance counter interrupt was pending, so we have to run
+	 * the performance counter interrupt handler anyway.
+	 */
+	if (handle_perf_irq(r2))
+		return IRQ_HANDLED;
+
+	/*
+	 * The same applies to performance counter interrupts.	But with the
+	 * above we now know that the reason we got here must be a timer
+	 * interrupt.  Being the paranoiacs we are we check anyway.
+	 */
+	if (!r2 || (read_c0_cause() & CAUSEF_TI)) {
+		/* Clear Count/Compare Interrupt */
+		write_c0_compare(read_c0_compare());
+		cd = &per_cpu(mips_clockevent_device, cpu);
+		cd->event_handler(cd);
+
+		return IRQ_HANDLED;
+	}
+
+	return IRQ_NONE;
+}
+
+struct irqaction c0_compare_irqaction = {
+	.handler = c0_compare_interrupt,
+	/*
+	 * IRQF_SHARED: The timer interrupt may be shared with other interrupts
+	 * such as perf counter and FDC interrupts.
+	 */
+	.flags = IRQF_PERCPU | IRQF_TIMER | IRQF_SHARED,
+	.name = "timer",
+};
+
+
+void mips_event_handler(struct clock_event_device *dev)
+{
+}
+
+/*
+ * FIXME: This doesn't hold for the relocated E9000 compare interrupt.
+ */
+static int c0_compare_int_pending(void)
+{
+	/* When cpu_has_mips_r2, this checks Cause.TI instead of Cause.IP7 */
+	return (read_c0_cause() >> cp0_compare_irq_shift) & (1ul << CAUSEB_IP);
+}
+
+/*
+ * Compare interrupt can be routed and latched outside the core,
+ * so wait up to worst case number of cycle counter ticks for timer interrupt
+ * changes to propagate to the cause register.
+ */
+#define COMPARE_INT_SEEN_TICKS 50
+
+int c0_compare_int_usable(void)
+{
+	unsigned int delta;
+	unsigned int cnt;
+
+	/*
+	 * IP7 already pending?	 Try to clear it by acking the timer.
+	 */
+	if (c0_compare_int_pending()) {
+		cnt = read_c0_count();
+		write_c0_compare(cnt);
+		back_to_back_c0_hazard();
+		while (read_c0_count() < (cnt  + COMPARE_INT_SEEN_TICKS))
+			if (!c0_compare_int_pending())
+				break;
+		if (c0_compare_int_pending())
+			return 0;
+	}
+
+	for (delta = 0x10; delta <= 0x400000; delta <<= 1) {
+		cnt = read_c0_count();
+		cnt += delta;
+		write_c0_compare(cnt);
+		back_to_back_c0_hazard();
+		if ((int)(read_c0_count() - cnt) < 0)
+		    break;
+		/* increase delta if the timer was already expired */
+	}
+
+	while ((int)(read_c0_count() - cnt) <= 0)
+		;	/* Wait for expiry  */
+
+	while (read_c0_count() < (cnt + COMPARE_INT_SEEN_TICKS))
+		if (c0_compare_int_pending())
+			break;
+	if (!c0_compare_int_pending())
+		return 0;
+	cnt = read_c0_count();
+	write_c0_compare(cnt);
+	back_to_back_c0_hazard();
+	while (read_c0_count() < (cnt + COMPARE_INT_SEEN_TICKS))
+		if (!c0_compare_int_pending())
+			break;
+	if (c0_compare_int_pending())
+		return 0;
+
+	/*
+	 * Feels like a real count / compare timer.
+	 */
+	return 1;
+}
+
+unsigned int __weak get_c0_compare_int(void)
+{
+	return MIPS_CPU_IRQ_BASE + cp0_compare_irq;
+}
+
+#ifdef CONFIG_CPU_FREQ
+
+static unsigned long mips_ref_freq;
+
+static int r4k_cpufreq_callback(struct notifier_block *nb,
+				unsigned long val, void *data)
+{
+	struct cpufreq_freqs *freq = data;
+	struct clock_event_device *cd;
+	unsigned long rate;
+	int cpu;
+
+	if (!mips_ref_freq)
+		mips_ref_freq = freq->old;
+
+	if (val == CPUFREQ_POSTCHANGE) {
+		rate = cpufreq_scale(mips_hpt_frequency, mips_ref_freq,
+				     freq->new);
+
+		for_each_cpu(cpu, freq->policy->cpus) {
+			cd = &per_cpu(mips_clockevent_device, cpu);
+
+			clockevents_update_freq(cd, rate);
+		}
+	}
+
+	return 0;
+}
+
+static struct notifier_block r4k_cpufreq_notifier = {
+	.notifier_call  = r4k_cpufreq_callback,
+};
+
+static int __init r4k_register_cpufreq_notifier(void)
+{
+	return cpufreq_register_notifier(&r4k_cpufreq_notifier,
+					 CPUFREQ_TRANSITION_NOTIFIER);
+
+}
+core_initcall(r4k_register_cpufreq_notifier);
+
+#endif /* !CONFIG_CPU_FREQ */
+
+int r4k_clockevent_init(void)
+{
+	unsigned long flags = IRQF_PERCPU | IRQF_TIMER | IRQF_SHARED;
+	unsigned int cpu = smp_processor_id();
+	struct clock_event_device *cd;
+	unsigned int irq, min_delta;
+
+	if (!cpu_has_counter || !mips_hpt_frequency)
+		return -ENXIO;
+
+	if (!c0_compare_int_usable())
+		return -ENXIO;
+
+	/*
+	 * With vectored interrupts things are getting platform specific.
+	 * get_c0_compare_int is a hook to allow a platform to return the
+	 * interrupt number of its liking.
+	 */
+	irq = get_c0_compare_int();
+
+	cd = &per_cpu(mips_clockevent_device, cpu);
+
+	cd->name		= "MIPS";
+	cd->features		= CLOCK_EVT_FEAT_ONESHOT |
+				  CLOCK_EVT_FEAT_C3STOP |
+				  CLOCK_EVT_FEAT_PERCPU;
+
+	min_delta		= calculate_min_delta();
+
+	cd->rating		= 300;
+	cd->irq			= irq;
+	cd->cpumask		= cpumask_of(cpu);
+	cd->set_next_event	= mips_next_event;
+	cd->event_handler	= mips_event_handler;
+
+	clockevents_config_and_register(cd, mips_hpt_frequency, min_delta, 0x7fffffff);
+
+	if (cp0_timer_irq_installed)
+		return 0;
+
+	cp0_timer_irq_installed = 1;
+
+	if (request_irq(irq, c0_compare_interrupt, flags, "timer",
+			c0_compare_interrupt))
+		pr_err("Failed to request irq %d (timer)\n", irq);
+
+	return 0;
+}
+
diff --git a/arch/mips/kernel/cevt-sb1250.c b/arch/mips/kernel/cevt-sb1250.c
new file mode 100644
index 000000000..0451273fa
--- /dev/null
+++ b/arch/mips/kernel/cevt-sb1250.c
@@ -0,0 +1,138 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2000, 2001 Broadcom Corporation
+ */
+#include <linux/clockchips.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/percpu.h>
+#include <linux/smp.h>
+
+#include <asm/addrspace.h>
+#include <asm/io.h>
+#include <asm/time.h>
+
+#include <asm/sibyte/sb1250.h>
+#include <asm/sibyte/sb1250_regs.h>
+#include <asm/sibyte/sb1250_int.h>
+#include <asm/sibyte/sb1250_scd.h>
+
+#define IMR_IP2_VAL	K_INT_MAP_I0
+#define IMR_IP3_VAL	K_INT_MAP_I1
+#define IMR_IP4_VAL	K_INT_MAP_I2
+
+/*
+ * The general purpose timer ticks at 1MHz independent if
+ * the rest of the system
+ */
+
+static int sibyte_shutdown(struct clock_event_device *evt)
+{
+	void __iomem *cfg;
+
+	cfg = IOADDR(A_SCD_TIMER_REGISTER(smp_processor_id(), R_SCD_TIMER_CFG));
+
+	/* Stop the timer until we actually program a shot */
+	__raw_writeq(0, cfg);
+
+	return 0;
+}
+
+static int sibyte_set_periodic(struct clock_event_device *evt)
+{
+	unsigned int cpu = smp_processor_id();
+	void __iomem *cfg, *init;
+
+	cfg = IOADDR(A_SCD_TIMER_REGISTER(cpu, R_SCD_TIMER_CFG));
+	init = IOADDR(A_SCD_TIMER_REGISTER(cpu, R_SCD_TIMER_INIT));
+
+	__raw_writeq(0, cfg);
+	__raw_writeq((V_SCD_TIMER_FREQ / HZ) - 1, init);
+	__raw_writeq(M_SCD_TIMER_ENABLE | M_SCD_TIMER_MODE_CONTINUOUS, cfg);
+
+	return 0;
+}
+
+static int sibyte_next_event(unsigned long delta, struct clock_event_device *cd)
+{
+	unsigned int cpu = smp_processor_id();
+	void __iomem *cfg, *init;
+
+	cfg = IOADDR(A_SCD_TIMER_REGISTER(cpu, R_SCD_TIMER_CFG));
+	init = IOADDR(A_SCD_TIMER_REGISTER(cpu, R_SCD_TIMER_INIT));
+
+	__raw_writeq(0, cfg);
+	__raw_writeq(delta - 1, init);
+	__raw_writeq(M_SCD_TIMER_ENABLE, cfg);
+
+	return 0;
+}
+
+static irqreturn_t sibyte_counter_handler(int irq, void *dev_id)
+{
+	unsigned int cpu = smp_processor_id();
+	struct clock_event_device *cd = dev_id;
+	void __iomem *cfg;
+	unsigned long tmode;
+
+	if (clockevent_state_periodic(cd))
+		tmode = M_SCD_TIMER_ENABLE | M_SCD_TIMER_MODE_CONTINUOUS;
+	else
+		tmode = 0;
+
+	/* ACK interrupt */
+	cfg = IOADDR(A_SCD_TIMER_REGISTER(cpu, R_SCD_TIMER_CFG));
+	____raw_writeq(tmode, cfg);
+
+	cd->event_handler(cd);
+
+	return IRQ_HANDLED;
+}
+
+static DEFINE_PER_CPU(struct clock_event_device, sibyte_hpt_clockevent);
+static DEFINE_PER_CPU(char [18], sibyte_hpt_name);
+
+void sb1250_clockevent_init(void)
+{
+	unsigned int cpu = smp_processor_id();
+	unsigned int irq = K_INT_TIMER_0 + cpu;
+	struct clock_event_device *cd = &per_cpu(sibyte_hpt_clockevent, cpu);
+	unsigned char *name = per_cpu(sibyte_hpt_name, cpu);
+	unsigned long flags = IRQF_PERCPU | IRQF_TIMER;
+
+	/* Only have 4 general purpose timers, and we use last one as hpt */
+	BUG_ON(cpu > 2);
+
+	sprintf(name, "sb1250-counter-%d", cpu);
+	cd->name		= name;
+	cd->features		= CLOCK_EVT_FEAT_PERIODIC |
+				  CLOCK_EVT_FEAT_ONESHOT;
+	clockevent_set_clock(cd, V_SCD_TIMER_FREQ);
+	cd->max_delta_ns	= clockevent_delta2ns(0x7fffff, cd);
+	cd->max_delta_ticks	= 0x7fffff;
+	cd->min_delta_ns	= clockevent_delta2ns(2, cd);
+	cd->min_delta_ticks	= 2;
+	cd->rating		= 200;
+	cd->irq			= irq;
+	cd->cpumask		= cpumask_of(cpu);
+	cd->set_next_event	= sibyte_next_event;
+	cd->set_state_shutdown	= sibyte_shutdown;
+	cd->set_state_periodic	= sibyte_set_periodic;
+	cd->set_state_oneshot	= sibyte_shutdown;
+	clockevents_register_device(cd);
+
+	sb1250_mask_irq(cpu, irq);
+
+	/*
+	 * Map the timer interrupt to IP[4] of this cpu
+	 */
+	__raw_writeq(IMR_IP4_VAL,
+		     IOADDR(A_IMR_REGISTER(cpu, R_IMR_INTERRUPT_MAP_BASE) +
+			    (irq << 3)));
+
+	sb1250_unmask_irq(cpu, irq);
+
+	irq_set_affinity(irq, cpumask_of(cpu));
+	if (request_irq(irq, sibyte_counter_handler, flags, name, cd))
+		pr_err("Failed to request irq %d (%s)\n", irq, name);
+}
diff --git a/arch/mips/kernel/cevt-txx9.c b/arch/mips/kernel/cevt-txx9.c
new file mode 100644
index 000000000..d761ead2e
--- /dev/null
+++ b/arch/mips/kernel/cevt-txx9.c
@@ -0,0 +1,220 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Based on linux/arch/mips/kernel/cevt-r4k.c,
+ *	    linux/arch/mips/jmr3927/rbhma3100/setup.c
+ *
+ * Copyright 2001 MontaVista Software Inc.
+ * Copyright (C) 2000-2001 Toshiba Corporation
+ * Copyright (C) 2007 MIPS Technologies, Inc.
+ * Copyright (C) 2007 Ralf Baechle <ralf@linux-mips.org>
+ */
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/sched_clock.h>
+#include <asm/time.h>
+#include <asm/txx9tmr.h>
+
+#define TCR_BASE (TXx9_TMTCR_CCDE | TXx9_TMTCR_CRE | TXx9_TMTCR_TMODE_ITVL)
+#define TIMER_CCD	0	/* 1/2 */
+#define TIMER_CLK(imclk)	((imclk) / (2 << TIMER_CCD))
+
+struct txx9_clocksource {
+	struct clocksource cs;
+	struct txx9_tmr_reg __iomem *tmrptr;
+};
+
+static u64 txx9_cs_read(struct clocksource *cs)
+{
+	struct txx9_clocksource *txx9_cs =
+		container_of(cs, struct txx9_clocksource, cs);
+	return __raw_readl(&txx9_cs->tmrptr->trr);
+}
+
+/* Use 1 bit smaller width to use full bits in that width */
+#define TXX9_CLOCKSOURCE_BITS (TXX9_TIMER_BITS - 1)
+
+static struct txx9_clocksource txx9_clocksource = {
+	.cs = {
+		.name		= "TXx9",
+		.rating		= 200,
+		.read		= txx9_cs_read,
+		.mask		= CLOCKSOURCE_MASK(TXX9_CLOCKSOURCE_BITS),
+		.flags		= CLOCK_SOURCE_IS_CONTINUOUS,
+	},
+};
+
+static u64 notrace txx9_read_sched_clock(void)
+{
+	return __raw_readl(&txx9_clocksource.tmrptr->trr);
+}
+
+void __init txx9_clocksource_init(unsigned long baseaddr,
+				  unsigned int imbusclk)
+{
+	struct txx9_tmr_reg __iomem *tmrptr;
+
+	clocksource_register_hz(&txx9_clocksource.cs, TIMER_CLK(imbusclk));
+
+	tmrptr = ioremap(baseaddr, sizeof(struct txx9_tmr_reg));
+	__raw_writel(TCR_BASE, &tmrptr->tcr);
+	__raw_writel(0, &tmrptr->tisr);
+	__raw_writel(TIMER_CCD, &tmrptr->ccdr);
+	__raw_writel(TXx9_TMITMR_TZCE, &tmrptr->itmr);
+	__raw_writel(1 << TXX9_CLOCKSOURCE_BITS, &tmrptr->cpra);
+	__raw_writel(TCR_BASE | TXx9_TMTCR_TCE, &tmrptr->tcr);
+	txx9_clocksource.tmrptr = tmrptr;
+
+	sched_clock_register(txx9_read_sched_clock, TXX9_CLOCKSOURCE_BITS,
+			     TIMER_CLK(imbusclk));
+}
+
+struct txx9_clock_event_device {
+	struct clock_event_device cd;
+	struct txx9_tmr_reg __iomem *tmrptr;
+};
+
+static void txx9tmr_stop_and_clear(struct txx9_tmr_reg __iomem *tmrptr)
+{
+	/* stop and reset counter */
+	__raw_writel(TCR_BASE, &tmrptr->tcr);
+	/* clear pending interrupt */
+	__raw_writel(0, &tmrptr->tisr);
+}
+
+static int txx9tmr_set_state_periodic(struct clock_event_device *evt)
+{
+	struct txx9_clock_event_device *txx9_cd =
+		container_of(evt, struct txx9_clock_event_device, cd);
+	struct txx9_tmr_reg __iomem *tmrptr = txx9_cd->tmrptr;
+
+	txx9tmr_stop_and_clear(tmrptr);
+
+	__raw_writel(TXx9_TMITMR_TIIE | TXx9_TMITMR_TZCE, &tmrptr->itmr);
+	/* start timer */
+	__raw_writel(((u64)(NSEC_PER_SEC / HZ) * evt->mult) >> evt->shift,
+		     &tmrptr->cpra);
+	__raw_writel(TCR_BASE | TXx9_TMTCR_TCE, &tmrptr->tcr);
+	return 0;
+}
+
+static int txx9tmr_set_state_oneshot(struct clock_event_device *evt)
+{
+	struct txx9_clock_event_device *txx9_cd =
+		container_of(evt, struct txx9_clock_event_device, cd);
+	struct txx9_tmr_reg __iomem *tmrptr = txx9_cd->tmrptr;
+
+	txx9tmr_stop_and_clear(tmrptr);
+	__raw_writel(TXx9_TMITMR_TIIE, &tmrptr->itmr);
+	return 0;
+}
+
+static int txx9tmr_set_state_shutdown(struct clock_event_device *evt)
+{
+	struct txx9_clock_event_device *txx9_cd =
+		container_of(evt, struct txx9_clock_event_device, cd);
+	struct txx9_tmr_reg __iomem *tmrptr = txx9_cd->tmrptr;
+
+	txx9tmr_stop_and_clear(tmrptr);
+	__raw_writel(0, &tmrptr->itmr);
+	return 0;
+}
+
+static int txx9tmr_tick_resume(struct clock_event_device *evt)
+{
+	struct txx9_clock_event_device *txx9_cd =
+		container_of(evt, struct txx9_clock_event_device, cd);
+	struct txx9_tmr_reg __iomem *tmrptr = txx9_cd->tmrptr;
+
+	txx9tmr_stop_and_clear(tmrptr);
+	__raw_writel(TIMER_CCD, &tmrptr->ccdr);
+	__raw_writel(0, &tmrptr->itmr);
+	return 0;
+}
+
+static int txx9tmr_set_next_event(unsigned long delta,
+				  struct clock_event_device *evt)
+{
+	struct txx9_clock_event_device *txx9_cd =
+		container_of(evt, struct txx9_clock_event_device, cd);
+	struct txx9_tmr_reg __iomem *tmrptr = txx9_cd->tmrptr;
+
+	txx9tmr_stop_and_clear(tmrptr);
+	/* start timer */
+	__raw_writel(delta, &tmrptr->cpra);
+	__raw_writel(TCR_BASE | TXx9_TMTCR_TCE, &tmrptr->tcr);
+	return 0;
+}
+
+static struct txx9_clock_event_device txx9_clock_event_device = {
+	.cd = {
+		.name			= "TXx9",
+		.features		= CLOCK_EVT_FEAT_PERIODIC |
+					  CLOCK_EVT_FEAT_ONESHOT,
+		.rating			= 200,
+		.set_state_shutdown	= txx9tmr_set_state_shutdown,
+		.set_state_periodic	= txx9tmr_set_state_periodic,
+		.set_state_oneshot	= txx9tmr_set_state_oneshot,
+		.tick_resume		= txx9tmr_tick_resume,
+		.set_next_event		= txx9tmr_set_next_event,
+	},
+};
+
+static irqreturn_t txx9tmr_interrupt(int irq, void *dev_id)
+{
+	struct txx9_clock_event_device *txx9_cd = dev_id;
+	struct clock_event_device *cd = &txx9_cd->cd;
+	struct txx9_tmr_reg __iomem *tmrptr = txx9_cd->tmrptr;
+
+	__raw_writel(0, &tmrptr->tisr); /* ack interrupt */
+	cd->event_handler(cd);
+	return IRQ_HANDLED;
+}
+
+void __init txx9_clockevent_init(unsigned long baseaddr, int irq,
+				 unsigned int imbusclk)
+{
+	struct clock_event_device *cd = &txx9_clock_event_device.cd;
+	struct txx9_tmr_reg __iomem *tmrptr;
+
+	tmrptr = ioremap(baseaddr, sizeof(struct txx9_tmr_reg));
+	txx9tmr_stop_and_clear(tmrptr);
+	__raw_writel(TIMER_CCD, &tmrptr->ccdr);
+	__raw_writel(0, &tmrptr->itmr);
+	txx9_clock_event_device.tmrptr = tmrptr;
+
+	clockevent_set_clock(cd, TIMER_CLK(imbusclk));
+	cd->max_delta_ns =
+		clockevent_delta2ns(0xffffffff >> (32 - TXX9_TIMER_BITS), cd);
+	cd->max_delta_ticks = 0xffffffff >> (32 - TXX9_TIMER_BITS);
+	cd->min_delta_ns = clockevent_delta2ns(0xf, cd);
+	cd->min_delta_ticks = 0xf;
+	cd->irq = irq;
+	cd->cpumask = cpumask_of(0);
+	clockevents_register_device(cd);
+	if (request_irq(irq, txx9tmr_interrupt, IRQF_PERCPU | IRQF_TIMER,
+			"txx9tmr", &txx9_clock_event_device))
+		pr_err("Failed to request irq %d (txx9tmr)\n", irq);
+	printk(KERN_INFO "TXx9: clockevent device at 0x%lx, irq %d\n",
+	       baseaddr, irq);
+}
+
+void __init txx9_tmr_init(unsigned long baseaddr)
+{
+	struct txx9_tmr_reg __iomem *tmrptr;
+
+	tmrptr = ioremap(baseaddr, sizeof(struct txx9_tmr_reg));
+	/* Start once to make CounterResetEnable effective */
+	__raw_writel(TXx9_TMTCR_CRE | TXx9_TMTCR_TCE, &tmrptr->tcr);
+	/* Stop and reset the counter */
+	__raw_writel(TXx9_TMTCR_CRE, &tmrptr->tcr);
+	__raw_writel(0, &tmrptr->tisr);
+	__raw_writel(0xffffffff, &tmrptr->cpra);
+	__raw_writel(0, &tmrptr->itmr);
+	__raw_writel(0, &tmrptr->ccdr);
+	__raw_writel(0, &tmrptr->pgmr);
+	iounmap(tmrptr);
+}
diff --git a/arch/mips/kernel/cmpxchg.c b/arch/mips/kernel/cmpxchg.c
new file mode 100644
index 000000000..e974a4954
--- /dev/null
+++ b/arch/mips/kernel/cmpxchg.c
@@ -0,0 +1,104 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2017 Imagination Technologies
+ * Author: Paul Burton <paul.burton@mips.com>
+ */
+
+#include <linux/bitops.h>
+#include <asm/cmpxchg.h>
+
+unsigned long __xchg_small(volatile void *ptr, unsigned long val, unsigned int size)
+{
+	u32 old32, new32, load32, mask;
+	volatile u32 *ptr32;
+	unsigned int shift;
+
+	/* Check that ptr is naturally aligned */
+	WARN_ON((unsigned long)ptr & (size - 1));
+
+	/* Mask value to the correct size. */
+	mask = GENMASK((size * BITS_PER_BYTE) - 1, 0);
+	val &= mask;
+
+	/*
+	 * Calculate a shift & mask that correspond to the value we wish to
+	 * exchange within the naturally aligned 4 byte integer that includes
+	 * it.
+	 */
+	shift = (unsigned long)ptr & 0x3;
+	if (IS_ENABLED(CONFIG_CPU_BIG_ENDIAN))
+		shift ^= sizeof(u32) - size;
+	shift *= BITS_PER_BYTE;
+	mask <<= shift;
+
+	/*
+	 * Calculate a pointer to the naturally aligned 4 byte integer that
+	 * includes our byte of interest, and load its value.
+	 */
+	ptr32 = (volatile u32 *)((unsigned long)ptr & ~0x3);
+	load32 = *ptr32;
+
+	do {
+		old32 = load32;
+		new32 = (load32 & ~mask) | (val << shift);
+		load32 = arch_cmpxchg(ptr32, old32, new32);
+	} while (load32 != old32);
+
+	return (load32 & mask) >> shift;
+}
+
+unsigned long __cmpxchg_small(volatile void *ptr, unsigned long old,
+			      unsigned long new, unsigned int size)
+{
+	u32 mask, old32, new32, load32, load;
+	volatile u32 *ptr32;
+	unsigned int shift;
+
+	/* Check that ptr is naturally aligned */
+	WARN_ON((unsigned long)ptr & (size - 1));
+
+	/* Mask inputs to the correct size. */
+	mask = GENMASK((size * BITS_PER_BYTE) - 1, 0);
+	old &= mask;
+	new &= mask;
+
+	/*
+	 * Calculate a shift & mask that correspond to the value we wish to
+	 * compare & exchange within the naturally aligned 4 byte integer
+	 * that includes it.
+	 */
+	shift = (unsigned long)ptr & 0x3;
+	if (IS_ENABLED(CONFIG_CPU_BIG_ENDIAN))
+		shift ^= sizeof(u32) - size;
+	shift *= BITS_PER_BYTE;
+	mask <<= shift;
+
+	/*
+	 * Calculate a pointer to the naturally aligned 4 byte integer that
+	 * includes our byte of interest, and load its value.
+	 */
+	ptr32 = (volatile u32 *)((unsigned long)ptr & ~0x3);
+	load32 = *ptr32;
+
+	while (true) {
+		/*
+		 * Ensure the byte we want to exchange matches the expected
+		 * old value, and if not then bail.
+		 */
+		load = (load32 & mask) >> shift;
+		if (load != old)
+			return load;
+
+		/*
+		 * Calculate the old & new values of the naturally aligned
+		 * 4 byte integer that include the byte we want to exchange.
+		 * Attempt to exchange the old value for the new value, and
+		 * return if we succeed.
+		 */
+		old32 = (load32 & ~mask) | (old << shift);
+		new32 = (load32 & ~mask) | (new << shift);
+		load32 = arch_cmpxchg(ptr32, old32, new32);
+		if (load32 == old32)
+			return old;
+	}
+}
diff --git a/arch/mips/kernel/cps-vec-ns16550.S b/arch/mips/kernel/cps-vec-ns16550.S
new file mode 100644
index 000000000..30725e1df
--- /dev/null
+++ b/arch/mips/kernel/cps-vec-ns16550.S
@@ -0,0 +1,212 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2015 Imagination Technologies
+ * Author: Paul Burton <paul.burton@mips.com>
+ */
+
+#include <asm/addrspace.h>
+#include <asm/asm.h>
+#include <asm/asm-offsets.h>
+#include <asm/mipsregs.h>
+#include <asm/regdef.h>
+#include <linux/serial_reg.h>
+
+#define UART_TX_OFS	(UART_TX << CONFIG_MIPS_CPS_NS16550_SHIFT)
+#define UART_LSR_OFS	(UART_LSR << CONFIG_MIPS_CPS_NS16550_SHIFT)
+
+#if CONFIG_MIPS_CPS_NS16550_WIDTH == 1
+# define UART_L		lb
+# define UART_S		sb
+#elif CONFIG_MIPS_CPS_NS16550_WIDTH == 2
+# define UART_L		lh
+# define UART_S		sh
+#elif CONFIG_MIPS_CPS_NS16550_WIDTH == 4
+# define UART_L		lw
+# define UART_S		sw
+#else
+# define UART_L		lb
+# define UART_S		sb
+#endif
+
+/**
+ * _mips_cps_putc() - write a character to the UART
+ * @a0: ASCII character to write
+ * @t9: UART base address
+ */
+LEAF(_mips_cps_putc)
+1:	UART_L		t0, UART_LSR_OFS(t9)
+	andi		t0, t0, UART_LSR_TEMT
+	beqz		t0, 1b
+	UART_S		a0, UART_TX_OFS(t9)
+	jr		ra
+	END(_mips_cps_putc)
+
+/**
+ * _mips_cps_puts() - write a string to the UART
+ * @a0: pointer to NULL-terminated ASCII string
+ * @t9: UART base address
+ *
+ * Write a null-terminated ASCII string to the UART.
+ */
+NESTED(_mips_cps_puts, 0, ra)
+	move		s7, ra
+	move		s6, a0
+
+1:	lb		a0, 0(s6)
+	beqz		a0, 2f
+	jal		_mips_cps_putc
+	PTR_ADDIU	s6, s6, 1
+	b		1b
+
+2:	jr		s7
+	END(_mips_cps_puts)
+
+/**
+ * _mips_cps_putx4 - write a 4b hex value to the UART
+ * @a0: the 4b value to write to the UART
+ * @t9: UART base address
+ *
+ * Write a single hexadecimal character to the UART.
+ */
+NESTED(_mips_cps_putx4, 0, ra)
+	andi		a0, a0, 0xf
+	li		t0, '0'
+	blt		a0, 10, 1f
+	li		t0, 'a'
+	addiu		a0, a0, -10
+1:	addu		a0, a0, t0
+	b		_mips_cps_putc
+	END(_mips_cps_putx4)
+
+/**
+ * _mips_cps_putx8 - write an 8b hex value to the UART
+ * @a0: the 8b value to write to the UART
+ * @t9: UART base address
+ *
+ * Write an 8 bit value (ie. 2 hexadecimal characters) to the UART.
+ */
+NESTED(_mips_cps_putx8, 0, ra)
+	move		s3, ra
+	move		s2, a0
+	srl		a0, a0, 4
+	jal		_mips_cps_putx4
+	move		a0, s2
+	move		ra, s3
+	b		_mips_cps_putx4
+	END(_mips_cps_putx8)
+
+/**
+ * _mips_cps_putx16 - write a 16b hex value to the UART
+ * @a0: the 16b value to write to the UART
+ * @t9: UART base address
+ *
+ * Write a 16 bit value (ie. 4 hexadecimal characters) to the UART.
+ */
+NESTED(_mips_cps_putx16, 0, ra)
+	move		s5, ra
+	move		s4, a0
+	srl		a0, a0, 8
+	jal		_mips_cps_putx8
+	move		a0, s4
+	move		ra, s5
+	b		_mips_cps_putx8
+	END(_mips_cps_putx16)
+
+/**
+ * _mips_cps_putx32 - write a 32b hex value to the UART
+ * @a0: the 32b value to write to the UART
+ * @t9: UART base address
+ *
+ * Write a 32 bit value (ie. 8 hexadecimal characters) to the UART.
+ */
+NESTED(_mips_cps_putx32, 0, ra)
+	move		s7, ra
+	move		s6, a0
+	srl		a0, a0, 16
+	jal		_mips_cps_putx16
+	move		a0, s6
+	move		ra, s7
+	b		_mips_cps_putx16
+	END(_mips_cps_putx32)
+
+#ifdef CONFIG_64BIT
+
+/**
+ * _mips_cps_putx64 - write a 64b hex value to the UART
+ * @a0: the 64b value to write to the UART
+ * @t9: UART base address
+ *
+ * Write a 64 bit value (ie. 16 hexadecimal characters) to the UART.
+ */
+NESTED(_mips_cps_putx64, 0, ra)
+	move		sp, ra
+	move		s8, a0
+	dsrl32		a0, a0, 0
+	jal		_mips_cps_putx32
+	move		a0, s8
+	move		ra, sp
+	b		_mips_cps_putx32
+	END(_mips_cps_putx64)
+
+#define _mips_cps_putxlong _mips_cps_putx64
+
+#else /* !CONFIG_64BIT */
+
+#define _mips_cps_putxlong _mips_cps_putx32
+
+#endif /* !CONFIG_64BIT */
+
+/**
+ * mips_cps_bev_dump() - dump relevant exception state to UART
+ * @a0: pointer to NULL-terminated ASCII string naming the exception
+ *
+ * Write information that may be useful in debugging an exception to the
+ * UART configured by CONFIG_MIPS_CPS_NS16550_*. As this BEV exception
+ * will only be run if something goes horribly wrong very early during
+ * the bringup of a core and it is very likely to be unsafe to perform
+ * memory accesses at that point (cache state indeterminate, EVA may not
+ * be configured, coherence may be disabled) let alone have a stack,
+ * this is all written in assembly using only registers & unmapped
+ * uncached access to the UART registers.
+ */
+LEAF(mips_cps_bev_dump)
+	move		s0, ra
+	move		s1, a0
+
+	li		t9, CKSEG1ADDR(CONFIG_MIPS_CPS_NS16550_BASE)
+
+	PTR_LA		a0, str_newline
+	jal		_mips_cps_puts
+	PTR_LA		a0, str_bev
+	jal		_mips_cps_puts
+	move		a0, s1
+	jal		_mips_cps_puts
+	PTR_LA		a0, str_newline
+	jal		_mips_cps_puts
+	PTR_LA		a0, str_newline
+	jal		_mips_cps_puts
+
+#define DUMP_COP0_REG(reg, name, sz, _mfc0)		\
+	PTR_LA		a0, 8f;				\
+	jal		_mips_cps_puts;			\
+	_mfc0		a0, reg;			\
+	jal		_mips_cps_putx##sz;		\
+	PTR_LA		a0, str_newline;		\
+	jal		_mips_cps_puts;			\
+	TEXT(name)
+
+	DUMP_COP0_REG(CP0_CAUSE,    "Cause:    0x", 32, mfc0)
+	DUMP_COP0_REG(CP0_STATUS,   "Status:   0x", 32, mfc0)
+	DUMP_COP0_REG(CP0_EBASE,    "EBase:    0x", long, MFC0)
+	DUMP_COP0_REG(CP0_BADVADDR, "BadVAddr: 0x", long, MFC0)
+	DUMP_COP0_REG(CP0_BADINSTR, "BadInstr: 0x", 32, mfc0)
+
+	PTR_LA		a0, str_newline
+	jal		_mips_cps_puts
+	jr		s0
+	END(mips_cps_bev_dump)
+
+.pushsection	.data
+str_bev: .asciiz "BEV Exception: "
+str_newline: .asciiz "\r\n"
+.popsection
diff --git a/arch/mips/kernel/cps-vec.S b/arch/mips/kernel/cps-vec.S
new file mode 100644
index 000000000..975343240
--- /dev/null
+++ b/arch/mips/kernel/cps-vec.S
@@ -0,0 +1,629 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2013 Imagination Technologies
+ * Author: Paul Burton <paul.burton@mips.com>
+ */
+
+#include <asm/addrspace.h>
+#include <asm/asm.h>
+#include <asm/asm-offsets.h>
+#include <asm/asmmacro.h>
+#include <asm/cacheops.h>
+#include <asm/eva.h>
+#include <asm/mipsregs.h>
+#include <asm/mipsmtregs.h>
+#include <asm/pm.h>
+
+#define GCR_CPC_BASE_OFS	0x0088
+#define GCR_CL_COHERENCE_OFS	0x2008
+#define GCR_CL_ID_OFS		0x2028
+
+#define CPC_CL_VC_STOP_OFS	0x2020
+#define CPC_CL_VC_RUN_OFS	0x2028
+
+.extern mips_cm_base
+
+.set noreorder
+
+#ifdef CONFIG_64BIT
+# define STATUS_BITDEPS		ST0_KX
+#else
+# define STATUS_BITDEPS		0
+#endif
+
+#ifdef CONFIG_MIPS_CPS_NS16550
+
+#define DUMP_EXCEP(name)		\
+	PTR_LA	a0, 8f;			\
+	jal	mips_cps_bev_dump;	\
+	 nop;				\
+	TEXT(name)
+
+#else /* !CONFIG_MIPS_CPS_NS16550 */
+
+#define DUMP_EXCEP(name)
+
+#endif /* !CONFIG_MIPS_CPS_NS16550 */
+
+	/*
+	 * Set dest to non-zero if the core supports the MT ASE, else zero. If
+	 * MT is not supported then branch to nomt.
+	 */
+	.macro	has_mt	dest, nomt
+	mfc0	\dest, CP0_CONFIG, 1
+	bgez	\dest, \nomt
+	 mfc0	\dest, CP0_CONFIG, 2
+	bgez	\dest, \nomt
+	 mfc0	\dest, CP0_CONFIG, 3
+	andi	\dest, \dest, MIPS_CONF3_MT
+	beqz	\dest, \nomt
+	 nop
+	.endm
+
+	/*
+	 * Set dest to non-zero if the core supports MIPSr6 multithreading
+	 * (ie. VPs), else zero. If MIPSr6 multithreading is not supported then
+	 * branch to nomt.
+	 */
+	.macro	has_vp	dest, nomt
+	mfc0	\dest, CP0_CONFIG, 1
+	bgez	\dest, \nomt
+	 mfc0	\dest, CP0_CONFIG, 2
+	bgez	\dest, \nomt
+	 mfc0	\dest, CP0_CONFIG, 3
+	bgez	\dest, \nomt
+	 mfc0	\dest, CP0_CONFIG, 4
+	bgez	\dest, \nomt
+	 mfc0	\dest, CP0_CONFIG, 5
+	andi	\dest, \dest, MIPS_CONF5_VP
+	beqz	\dest, \nomt
+	 nop
+	.endm
+
+	/* Calculate an uncached address for the CM GCRs */
+	.macro	cmgcrb	dest
+	.set	push
+	.set	noat
+	MFC0	$1, CP0_CMGCRBASE
+	PTR_SLL	$1, $1, 4
+	PTR_LI	\dest, UNCAC_BASE
+	PTR_ADDU \dest, \dest, $1
+	.set	pop
+	.endm
+
+.balign 0x1000
+
+LEAF(mips_cps_core_entry)
+	/*
+	 * These first 4 bytes will be patched by cps_smp_setup to load the
+	 * CCA to use into register s0.
+	 */
+	.word	0
+
+	/* Check whether we're here due to an NMI */
+	mfc0	k0, CP0_STATUS
+	and	k0, k0, ST0_NMI
+	beqz	k0, not_nmi
+	 nop
+
+	/* This is an NMI */
+	PTR_LA	k0, nmi_handler
+	jr	k0
+	 nop
+
+not_nmi:
+	/* Setup Cause */
+	li	t0, CAUSEF_IV
+	mtc0	t0, CP0_CAUSE
+
+	/* Setup Status */
+	li	t0, ST0_CU1 | ST0_CU0 | ST0_BEV | STATUS_BITDEPS
+	mtc0	t0, CP0_STATUS
+
+	/* Skip cache & coherence setup if we're already coherent */
+	cmgcrb	v1
+	lw	s7, GCR_CL_COHERENCE_OFS(v1)
+	bnez	s7, 1f
+	 nop
+
+	/* Initialize the L1 caches */
+	jal	mips_cps_cache_init
+	 nop
+
+	/* Enter the coherent domain */
+	li	t0, 0xff
+	sw	t0, GCR_CL_COHERENCE_OFS(v1)
+	ehb
+
+	/* Set Kseg0 CCA to that in s0 */
+1:	mfc0	t0, CP0_CONFIG
+	ori	t0, 0x7
+	xori	t0, 0x7
+	or	t0, t0, s0
+	mtc0	t0, CP0_CONFIG
+	ehb
+
+	/* Jump to kseg0 */
+	PTR_LA	t0, 1f
+	jr	t0
+	 nop
+
+	/*
+	 * We're up, cached & coherent. Perform any EVA initialization necessary
+	 * before we access memory.
+	 */
+1:	eva_init
+
+	/* Retrieve boot configuration pointers */
+	jal	mips_cps_get_bootcfg
+	 nop
+
+	/* Skip core-level init if we started up coherent */
+	bnez	s7, 1f
+	 nop
+
+	/* Perform any further required core-level initialisation */
+	jal	mips_cps_core_init
+	 nop
+
+	/*
+	 * Boot any other VPEs within this core that should be online, and
+	 * deactivate this VPE if it should be offline.
+	 */
+	move	a1, t9
+	jal	mips_cps_boot_vpes
+	 move	a0, v0
+
+	/* Off we go! */
+1:	PTR_L	t1, VPEBOOTCFG_PC(v1)
+	PTR_L	gp, VPEBOOTCFG_GP(v1)
+	PTR_L	sp, VPEBOOTCFG_SP(v1)
+	jr	t1
+	 nop
+	END(mips_cps_core_entry)
+
+.org 0x200
+LEAF(excep_tlbfill)
+	DUMP_EXCEP("TLB Fill")
+	b	.
+	 nop
+	END(excep_tlbfill)
+
+.org 0x280
+LEAF(excep_xtlbfill)
+	DUMP_EXCEP("XTLB Fill")
+	b	.
+	 nop
+	END(excep_xtlbfill)
+
+.org 0x300
+LEAF(excep_cache)
+	DUMP_EXCEP("Cache")
+	b	.
+	 nop
+	END(excep_cache)
+
+.org 0x380
+LEAF(excep_genex)
+	DUMP_EXCEP("General")
+	b	.
+	 nop
+	END(excep_genex)
+
+.org 0x400
+LEAF(excep_intex)
+	DUMP_EXCEP("Interrupt")
+	b	.
+	 nop
+	END(excep_intex)
+
+.org 0x480
+LEAF(excep_ejtag)
+	PTR_LA	k0, ejtag_debug_handler
+	jr	k0
+	 nop
+	END(excep_ejtag)
+
+LEAF(mips_cps_core_init)
+#ifdef CONFIG_MIPS_MT_SMP
+	/* Check that the core implements the MT ASE */
+	has_mt	t0, 3f
+
+	.set	push
+	.set	MIPS_ISA_LEVEL_RAW
+	.set	mt
+
+	/* Only allow 1 TC per VPE to execute... */
+	dmt
+
+	/* ...and for the moment only 1 VPE */
+	dvpe
+	PTR_LA	t1, 1f
+	jr.hb	t1
+	 nop
+
+	/* Enter VPE configuration state */
+1:	mfc0	t0, CP0_MVPCONTROL
+	ori	t0, t0, MVPCONTROL_VPC
+	mtc0	t0, CP0_MVPCONTROL
+
+	/* Retrieve the number of VPEs within the core */
+	mfc0	t0, CP0_MVPCONF0
+	srl	t0, t0, MVPCONF0_PVPE_SHIFT
+	andi	t0, t0, (MVPCONF0_PVPE >> MVPCONF0_PVPE_SHIFT)
+	addiu	ta3, t0, 1
+
+	/* If there's only 1, we're done */
+	beqz	t0, 2f
+	 nop
+
+	/* Loop through each VPE within this core */
+	li	ta1, 1
+
+1:	/* Operate on the appropriate TC */
+	mtc0	ta1, CP0_VPECONTROL
+	ehb
+
+	/* Bind TC to VPE (1:1 TC:VPE mapping) */
+	mttc0	ta1, CP0_TCBIND
+
+	/* Set exclusive TC, non-active, master */
+	li	t0, VPECONF0_MVP
+	sll	t1, ta1, VPECONF0_XTC_SHIFT
+	or	t0, t0, t1
+	mttc0	t0, CP0_VPECONF0
+
+	/* Set TC non-active, non-allocatable */
+	mttc0	zero, CP0_TCSTATUS
+
+	/* Set TC halted */
+	li	t0, TCHALT_H
+	mttc0	t0, CP0_TCHALT
+
+	/* Next VPE */
+	addiu	ta1, ta1, 1
+	slt	t0, ta1, ta3
+	bnez	t0, 1b
+	 nop
+
+	/* Leave VPE configuration state */
+2:	mfc0	t0, CP0_MVPCONTROL
+	xori	t0, t0, MVPCONTROL_VPC
+	mtc0	t0, CP0_MVPCONTROL
+
+3:	.set	pop
+#endif
+	jr	ra
+	 nop
+	END(mips_cps_core_init)
+
+/**
+ * mips_cps_get_bootcfg() - retrieve boot configuration pointers
+ *
+ * Returns: pointer to struct core_boot_config in v0, pointer to
+ *          struct vpe_boot_config in v1, VPE ID in t9
+ */
+LEAF(mips_cps_get_bootcfg)
+	/* Calculate a pointer to this cores struct core_boot_config */
+	cmgcrb	t0
+	lw	t0, GCR_CL_ID_OFS(t0)
+	li	t1, COREBOOTCFG_SIZE
+	mul	t0, t0, t1
+	PTR_LA	t1, mips_cps_core_bootcfg
+	PTR_L	t1, 0(t1)
+	PTR_ADDU v0, t0, t1
+
+	/* Calculate this VPEs ID. If the core doesn't support MT use 0 */
+	li	t9, 0
+#if defined(CONFIG_CPU_MIPSR6)
+	has_vp	ta2, 1f
+
+	/*
+	 * Assume non-contiguous numbering. Perhaps some day we'll need
+	 * to handle contiguous VP numbering, but no such systems yet
+	 * exist.
+	 */
+	mfc0	t9, CP0_GLOBALNUMBER
+	andi	t9, t9, MIPS_GLOBALNUMBER_VP
+#elif defined(CONFIG_MIPS_MT_SMP)
+	has_mt	ta2, 1f
+
+	/* Find the number of VPEs present in the core */
+	mfc0	t1, CP0_MVPCONF0
+	srl	t1, t1, MVPCONF0_PVPE_SHIFT
+	andi	t1, t1, MVPCONF0_PVPE >> MVPCONF0_PVPE_SHIFT
+	addiu	t1, t1, 1
+
+	/* Calculate a mask for the VPE ID from EBase.CPUNum */
+	clz	t1, t1
+	li	t2, 31
+	subu	t1, t2, t1
+	li	t2, 1
+	sll	t1, t2, t1
+	addiu	t1, t1, -1
+
+	/* Retrieve the VPE ID from EBase.CPUNum */
+	mfc0	t9, $15, 1
+	and	t9, t9, t1
+#endif
+
+1:	/* Calculate a pointer to this VPEs struct vpe_boot_config */
+	li	t1, VPEBOOTCFG_SIZE
+	mul	v1, t9, t1
+	PTR_L	ta3, COREBOOTCFG_VPECONFIG(v0)
+	PTR_ADDU v1, v1, ta3
+
+	jr	ra
+	 nop
+	END(mips_cps_get_bootcfg)
+
+LEAF(mips_cps_boot_vpes)
+	lw	ta2, COREBOOTCFG_VPEMASK(a0)
+	PTR_L	ta3, COREBOOTCFG_VPECONFIG(a0)
+
+#if defined(CONFIG_CPU_MIPSR6)
+
+	has_vp	t0, 5f
+
+	/* Find base address of CPC */
+	cmgcrb	t3
+	PTR_L	t1, GCR_CPC_BASE_OFS(t3)
+	PTR_LI	t2, ~0x7fff
+	and	t1, t1, t2
+	PTR_LI	t2, UNCAC_BASE
+	PTR_ADD	t1, t1, t2
+
+	/* Start any other VPs that ought to be running */
+	PTR_S	ta2, CPC_CL_VC_RUN_OFS(t1)
+
+	/* Ensure this VP stops running if it shouldn't be */
+	not	ta2
+	PTR_S	ta2, CPC_CL_VC_STOP_OFS(t1)
+	ehb
+
+#elif defined(CONFIG_MIPS_MT)
+
+	/* If the core doesn't support MT then return */
+	has_mt	t0, 5f
+
+	/* Enter VPE configuration state */
+	.set	push
+	.set	MIPS_ISA_LEVEL_RAW
+	.set	mt
+	dvpe
+	.set	pop
+
+	PTR_LA	t1, 1f
+	jr.hb	t1
+	 nop
+1:	mfc0	t1, CP0_MVPCONTROL
+	ori	t1, t1, MVPCONTROL_VPC
+	mtc0	t1, CP0_MVPCONTROL
+	ehb
+
+	/* Loop through each VPE */
+	move	t8, ta2
+	li	ta1, 0
+
+	/* Check whether the VPE should be running. If not, skip it */
+1:	andi	t0, ta2, 1
+	beqz	t0, 2f
+	 nop
+
+	/* Operate on the appropriate TC */
+	mfc0	t0, CP0_VPECONTROL
+	ori	t0, t0, VPECONTROL_TARGTC
+	xori	t0, t0, VPECONTROL_TARGTC
+	or	t0, t0, ta1
+	mtc0	t0, CP0_VPECONTROL
+	ehb
+
+	.set	push
+	.set	MIPS_ISA_LEVEL_RAW
+	.set	mt
+
+	/* Skip the VPE if its TC is not halted */
+	mftc0	t0, CP0_TCHALT
+	beqz	t0, 2f
+	 nop
+
+	/* Calculate a pointer to the VPEs struct vpe_boot_config */
+	li	t0, VPEBOOTCFG_SIZE
+	mul	t0, t0, ta1
+	addu	t0, t0, ta3
+
+	/* Set the TC restart PC */
+	lw	t1, VPEBOOTCFG_PC(t0)
+	mttc0	t1, CP0_TCRESTART
+
+	/* Set the TC stack pointer */
+	lw	t1, VPEBOOTCFG_SP(t0)
+	mttgpr	t1, sp
+
+	/* Set the TC global pointer */
+	lw	t1, VPEBOOTCFG_GP(t0)
+	mttgpr	t1, gp
+
+	/* Copy config from this VPE */
+	mfc0	t0, CP0_CONFIG
+	mttc0	t0, CP0_CONFIG
+
+	/*
+	 * Copy the EVA config from this VPE if the CPU supports it.
+	 * CONFIG3 must exist to be running MT startup - just read it.
+	 */
+	mfc0	t0, CP0_CONFIG, 3
+	and	t0, t0, MIPS_CONF3_SC
+	beqz	t0, 3f
+	 nop
+	mfc0    t0, CP0_SEGCTL0
+	mttc0	t0, CP0_SEGCTL0
+	mfc0    t0, CP0_SEGCTL1
+	mttc0	t0, CP0_SEGCTL1
+	mfc0    t0, CP0_SEGCTL2
+	mttc0	t0, CP0_SEGCTL2
+3:
+	/* Ensure no software interrupts are pending */
+	mttc0	zero, CP0_CAUSE
+	mttc0	zero, CP0_STATUS
+
+	/* Set TC active, not interrupt exempt */
+	mftc0	t0, CP0_TCSTATUS
+	li	t1, ~TCSTATUS_IXMT
+	and	t0, t0, t1
+	ori	t0, t0, TCSTATUS_A
+	mttc0	t0, CP0_TCSTATUS
+
+	/* Clear the TC halt bit */
+	mttc0	zero, CP0_TCHALT
+
+	/* Set VPE active */
+	mftc0	t0, CP0_VPECONF0
+	ori	t0, t0, VPECONF0_VPA
+	mttc0	t0, CP0_VPECONF0
+
+	/* Next VPE */
+2:	srl	ta2, ta2, 1
+	addiu	ta1, ta1, 1
+	bnez	ta2, 1b
+	 nop
+
+	/* Leave VPE configuration state */
+	mfc0	t1, CP0_MVPCONTROL
+	xori	t1, t1, MVPCONTROL_VPC
+	mtc0	t1, CP0_MVPCONTROL
+	ehb
+	evpe
+
+	.set	pop
+
+	/* Check whether this VPE is meant to be running */
+	li	t0, 1
+	sll	t0, t0, a1
+	and	t0, t0, t8
+	bnez	t0, 2f
+	 nop
+
+	/* This VPE should be offline, halt the TC */
+	li	t0, TCHALT_H
+	mtc0	t0, CP0_TCHALT
+	PTR_LA	t0, 1f
+1:	jr.hb	t0
+	 nop
+
+2:
+
+#endif /* CONFIG_MIPS_MT_SMP */
+
+	/* Return */
+5:	jr	ra
+	 nop
+	END(mips_cps_boot_vpes)
+
+LEAF(mips_cps_cache_init)
+	/*
+	 * Clear the bits used to index the caches. Note that the architecture
+	 * dictates that writing to any of TagLo or TagHi selects 0 or 2 should
+	 * be valid for all MIPS32 CPUs, even those for which said writes are
+	 * unnecessary.
+	 */
+	mtc0	zero, CP0_TAGLO, 0
+	mtc0	zero, CP0_TAGHI, 0
+	mtc0	zero, CP0_TAGLO, 2
+	mtc0	zero, CP0_TAGHI, 2
+	ehb
+
+	/* Primary cache configuration is indicated by Config1 */
+	mfc0	v0, CP0_CONFIG, 1
+
+	/* Detect I-cache line size */
+	_EXT	t0, v0, MIPS_CONF1_IL_SHF, MIPS_CONF1_IL_SZ
+	beqz	t0, icache_done
+	 li	t1, 2
+	sllv	t0, t1, t0
+
+	/* Detect I-cache size */
+	_EXT	t1, v0, MIPS_CONF1_IS_SHF, MIPS_CONF1_IS_SZ
+	xori	t2, t1, 0x7
+	beqz	t2, 1f
+	 li	t3, 32
+	addiu	t1, t1, 1
+	sllv	t1, t3, t1
+1:	/* At this point t1 == I-cache sets per way */
+	_EXT	t2, v0, MIPS_CONF1_IA_SHF, MIPS_CONF1_IA_SZ
+	addiu	t2, t2, 1
+	mul	t1, t1, t0
+	mul	t1, t1, t2
+
+	li	a0, CKSEG0
+	PTR_ADD	a1, a0, t1
+1:	cache	Index_Store_Tag_I, 0(a0)
+	PTR_ADD	a0, a0, t0
+	bne	a0, a1, 1b
+	 nop
+icache_done:
+
+	/* Detect D-cache line size */
+	_EXT	t0, v0, MIPS_CONF1_DL_SHF, MIPS_CONF1_DL_SZ
+	beqz	t0, dcache_done
+	 li	t1, 2
+	sllv	t0, t1, t0
+
+	/* Detect D-cache size */
+	_EXT	t1, v0, MIPS_CONF1_DS_SHF, MIPS_CONF1_DS_SZ
+	xori	t2, t1, 0x7
+	beqz	t2, 1f
+	 li	t3, 32
+	addiu	t1, t1, 1
+	sllv	t1, t3, t1
+1:	/* At this point t1 == D-cache sets per way */
+	_EXT	t2, v0, MIPS_CONF1_DA_SHF, MIPS_CONF1_DA_SZ
+	addiu	t2, t2, 1
+	mul	t1, t1, t0
+	mul	t1, t1, t2
+
+	li	a0, CKSEG0
+	PTR_ADDU a1, a0, t1
+	PTR_SUBU a1, a1, t0
+1:	cache	Index_Store_Tag_D, 0(a0)
+	bne	a0, a1, 1b
+	 PTR_ADD a0, a0, t0
+dcache_done:
+
+	jr	ra
+	 nop
+	END(mips_cps_cache_init)
+
+#if defined(CONFIG_MIPS_CPS_PM) && defined(CONFIG_CPU_PM)
+
+	/* Calculate a pointer to this CPUs struct mips_static_suspend_state */
+	.macro	psstate	dest
+	.set	push
+	.set	noat
+	lw	$1, TI_CPU(gp)
+	sll	$1, $1, LONGLOG
+	PTR_LA	\dest, __per_cpu_offset
+	addu	$1, $1, \dest
+	lw	$1, 0($1)
+	PTR_LA	\dest, cps_cpu_state
+	addu	\dest, \dest, $1
+	.set	pop
+	.endm
+
+LEAF(mips_cps_pm_save)
+	/* Save CPU state */
+	SUSPEND_SAVE_REGS
+	psstate	t1
+	SUSPEND_SAVE_STATIC
+	jr	v0
+	 nop
+	END(mips_cps_pm_save)
+
+LEAF(mips_cps_pm_restore)
+	/* Restore CPU state */
+	psstate	t1
+	RESUME_RESTORE_STATIC
+	RESUME_RESTORE_REGS_RETURN
+	END(mips_cps_pm_restore)
+
+#endif /* CONFIG_MIPS_CPS_PM && CONFIG_CPU_PM */
diff --git a/arch/mips/kernel/cpu-probe.c b/arch/mips/kernel/cpu-probe.c
new file mode 100644
index 000000000..482af80b8
--- /dev/null
+++ b/arch/mips/kernel/cpu-probe.c
@@ -0,0 +1,2043 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Processor capabilities determination functions.
+ *
+ * Copyright (C) xxxx  the Anonymous
+ * Copyright (C) 1994 - 2006 Ralf Baechle
+ * Copyright (C) 2003, 2004  Maciej W. Rozycki
+ * Copyright (C) 2001, 2004, 2011, 2012	 MIPS Technologies, Inc.
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/ptrace.h>
+#include <linux/smp.h>
+#include <linux/stddef.h>
+#include <linux/export.h>
+
+#include <asm/bugs.h>
+#include <asm/cpu.h>
+#include <asm/cpu-features.h>
+#include <asm/cpu-type.h>
+#include <asm/fpu.h>
+#include <asm/mipsregs.h>
+#include <asm/mipsmtregs.h>
+#include <asm/msa.h>
+#include <asm/watch.h>
+#include <asm/elf.h>
+#include <asm/pgtable-bits.h>
+#include <asm/spram.h>
+#include <asm/traps.h>
+#include <linux/uaccess.h>
+
+#include "fpu-probe.h"
+
+#include <asm/mach-loongson64/cpucfg-emul.h>
+
+/* Hardware capabilities */
+unsigned int elf_hwcap __read_mostly;
+EXPORT_SYMBOL_GPL(elf_hwcap);
+
+static inline unsigned long cpu_get_msa_id(void)
+{
+	unsigned long status, msa_id;
+
+	status = read_c0_status();
+	__enable_fpu(FPU_64BIT);
+	enable_msa();
+	msa_id = read_msa_ir();
+	disable_msa();
+	write_c0_status(status);
+	return msa_id;
+}
+
+static int mips_dsp_disabled;
+
+static int __init dsp_disable(char *s)
+{
+	cpu_data[0].ases &= ~(MIPS_ASE_DSP | MIPS_ASE_DSP2P);
+	mips_dsp_disabled = 1;
+
+	return 1;
+}
+
+__setup("nodsp", dsp_disable);
+
+static int mips_htw_disabled;
+
+static int __init htw_disable(char *s)
+{
+	mips_htw_disabled = 1;
+	cpu_data[0].options &= ~MIPS_CPU_HTW;
+	write_c0_pwctl(read_c0_pwctl() &
+		       ~(1 << MIPS_PWCTL_PWEN_SHIFT));
+
+	return 1;
+}
+
+__setup("nohtw", htw_disable);
+
+static int mips_ftlb_disabled;
+static int mips_has_ftlb_configured;
+
+enum ftlb_flags {
+	FTLB_EN		= 1 << 0,
+	FTLB_SET_PROB	= 1 << 1,
+};
+
+static int set_ftlb_enable(struct cpuinfo_mips *c, enum ftlb_flags flags);
+
+static int __init ftlb_disable(char *s)
+{
+	unsigned int config4, mmuextdef;
+
+	/*
+	 * If the core hasn't done any FTLB configuration, there is nothing
+	 * for us to do here.
+	 */
+	if (!mips_has_ftlb_configured)
+		return 1;
+
+	/* Disable it in the boot cpu */
+	if (set_ftlb_enable(&cpu_data[0], 0)) {
+		pr_warn("Can't turn FTLB off\n");
+		return 1;
+	}
+
+	config4 = read_c0_config4();
+
+	/* Check that FTLB has been disabled */
+	mmuextdef = config4 & MIPS_CONF4_MMUEXTDEF;
+	/* MMUSIZEEXT == VTLB ON, FTLB OFF */
+	if (mmuextdef == MIPS_CONF4_MMUEXTDEF_FTLBSIZEEXT) {
+		/* This should never happen */
+		pr_warn("FTLB could not be disabled!\n");
+		return 1;
+	}
+
+	mips_ftlb_disabled = 1;
+	mips_has_ftlb_configured = 0;
+
+	/*
+	 * noftlb is mainly used for debug purposes so print
+	 * an informative message instead of using pr_debug()
+	 */
+	pr_info("FTLB has been disabled\n");
+
+	/*
+	 * Some of these bits are duplicated in the decode_config4.
+	 * MIPS_CONF4_MMUEXTDEF_MMUSIZEEXT is the only possible case
+	 * once FTLB has been disabled so undo what decode_config4 did.
+	 */
+	cpu_data[0].tlbsize -= cpu_data[0].tlbsizeftlbways *
+			       cpu_data[0].tlbsizeftlbsets;
+	cpu_data[0].tlbsizeftlbsets = 0;
+	cpu_data[0].tlbsizeftlbways = 0;
+
+	return 1;
+}
+
+__setup("noftlb", ftlb_disable);
+
+/*
+ * Check if the CPU has per tc perf counters
+ */
+static inline void cpu_set_mt_per_tc_perf(struct cpuinfo_mips *c)
+{
+	if (read_c0_config7() & MTI_CONF7_PTC)
+		c->options |= MIPS_CPU_MT_PER_TC_PERF_COUNTERS;
+}
+
+static inline void check_errata(void)
+{
+	struct cpuinfo_mips *c = &current_cpu_data;
+
+	switch (current_cpu_type()) {
+	case CPU_34K:
+		/*
+		 * Erratum "RPS May Cause Incorrect Instruction Execution"
+		 * This code only handles VPE0, any SMP/RTOS code
+		 * making use of VPE1 will be responsible for that VPE.
+		 */
+		if ((c->processor_id & PRID_REV_MASK) <= PRID_REV_34K_V1_0_2)
+			write_c0_config7(read_c0_config7() | MIPS_CONF7_RPS);
+		break;
+	default:
+		break;
+	}
+}
+
+void __init check_bugs32(void)
+{
+	check_errata();
+}
+
+/*
+ * Probe whether cpu has config register by trying to play with
+ * alternate cache bit and see whether it matters.
+ * It's used by cpu_probe to distinguish between R3000A and R3081.
+ */
+static inline int cpu_has_confreg(void)
+{
+#ifdef CONFIG_CPU_R3000
+	extern unsigned long r3k_cache_size(unsigned long);
+	unsigned long size1, size2;
+	unsigned long cfg = read_c0_conf();
+
+	size1 = r3k_cache_size(ST0_ISC);
+	write_c0_conf(cfg ^ R30XX_CONF_AC);
+	size2 = r3k_cache_size(ST0_ISC);
+	write_c0_conf(cfg);
+	return size1 != size2;
+#else
+	return 0;
+#endif
+}
+
+static inline void set_elf_platform(int cpu, const char *plat)
+{
+	if (cpu == 0)
+		__elf_platform = plat;
+}
+
+static inline void set_elf_base_platform(const char *plat)
+{
+	if (__elf_base_platform == NULL) {
+		__elf_base_platform = plat;
+	}
+}
+
+static inline void cpu_probe_vmbits(struct cpuinfo_mips *c)
+{
+#ifdef __NEED_VMBITS_PROBE
+	write_c0_entryhi(0x3fffffffffffe000ULL);
+	back_to_back_c0_hazard();
+	c->vmbits = fls64(read_c0_entryhi() & 0x3fffffffffffe000ULL);
+#endif
+}
+
+static void set_isa(struct cpuinfo_mips *c, unsigned int isa)
+{
+	switch (isa) {
+	case MIPS_CPU_ISA_M64R5:
+		c->isa_level |= MIPS_CPU_ISA_M32R5 | MIPS_CPU_ISA_M64R5;
+		set_elf_base_platform("mips64r5");
+		fallthrough;
+	case MIPS_CPU_ISA_M64R2:
+		c->isa_level |= MIPS_CPU_ISA_M32R2 | MIPS_CPU_ISA_M64R2;
+		set_elf_base_platform("mips64r2");
+		fallthrough;
+	case MIPS_CPU_ISA_M64R1:
+		c->isa_level |= MIPS_CPU_ISA_M32R1 | MIPS_CPU_ISA_M64R1;
+		set_elf_base_platform("mips64");
+		fallthrough;
+	case MIPS_CPU_ISA_V:
+		c->isa_level |= MIPS_CPU_ISA_V;
+		set_elf_base_platform("mips5");
+		fallthrough;
+	case MIPS_CPU_ISA_IV:
+		c->isa_level |= MIPS_CPU_ISA_IV;
+		set_elf_base_platform("mips4");
+		fallthrough;
+	case MIPS_CPU_ISA_III:
+		c->isa_level |= MIPS_CPU_ISA_II | MIPS_CPU_ISA_III;
+		set_elf_base_platform("mips3");
+		break;
+
+	/* R6 incompatible with everything else */
+	case MIPS_CPU_ISA_M64R6:
+		c->isa_level |= MIPS_CPU_ISA_M32R6 | MIPS_CPU_ISA_M64R6;
+		set_elf_base_platform("mips64r6");
+		fallthrough;
+	case MIPS_CPU_ISA_M32R6:
+		c->isa_level |= MIPS_CPU_ISA_M32R6;
+		set_elf_base_platform("mips32r6");
+		/* Break here so we don't add incompatible ISAs */
+		break;
+	case MIPS_CPU_ISA_M32R5:
+		c->isa_level |= MIPS_CPU_ISA_M32R5;
+		set_elf_base_platform("mips32r5");
+		fallthrough;
+	case MIPS_CPU_ISA_M32R2:
+		c->isa_level |= MIPS_CPU_ISA_M32R2;
+		set_elf_base_platform("mips32r2");
+		fallthrough;
+	case MIPS_CPU_ISA_M32R1:
+		c->isa_level |= MIPS_CPU_ISA_M32R1;
+		set_elf_base_platform("mips32");
+		fallthrough;
+	case MIPS_CPU_ISA_II:
+		c->isa_level |= MIPS_CPU_ISA_II;
+		set_elf_base_platform("mips2");
+		break;
+	}
+}
+
+static char unknown_isa[] = KERN_ERR \
+	"Unsupported ISA type, c0.config0: %d.";
+
+static unsigned int calculate_ftlb_probability(struct cpuinfo_mips *c)
+{
+
+	unsigned int probability = c->tlbsize / c->tlbsizevtlb;
+
+	/*
+	 * 0 = All TLBWR instructions go to FTLB
+	 * 1 = 15:1: For every 16 TBLWR instructions, 15 go to the
+	 * FTLB and 1 goes to the VTLB.
+	 * 2 = 7:1: As above with 7:1 ratio.
+	 * 3 = 3:1: As above with 3:1 ratio.
+	 *
+	 * Use the linear midpoint as the probability threshold.
+	 */
+	if (probability >= 12)
+		return 1;
+	else if (probability >= 6)
+		return 2;
+	else
+		/*
+		 * So FTLB is less than 4 times bigger than VTLB.
+		 * A 3:1 ratio can still be useful though.
+		 */
+		return 3;
+}
+
+static int set_ftlb_enable(struct cpuinfo_mips *c, enum ftlb_flags flags)
+{
+	unsigned int config;
+
+	/* It's implementation dependent how the FTLB can be enabled */
+	switch (c->cputype) {
+	case CPU_PROAPTIV:
+	case CPU_P5600:
+	case CPU_P6600:
+		/* proAptiv & related cores use Config6 to enable the FTLB */
+		config = read_c0_config6();
+
+		if (flags & FTLB_EN)
+			config |= MTI_CONF6_FTLBEN;
+		else
+			config &= ~MTI_CONF6_FTLBEN;
+
+		if (flags & FTLB_SET_PROB) {
+			config &= ~(3 << MTI_CONF6_FTLBP_SHIFT);
+			config |= calculate_ftlb_probability(c)
+				  << MTI_CONF6_FTLBP_SHIFT;
+		}
+
+		write_c0_config6(config);
+		back_to_back_c0_hazard();
+		break;
+	case CPU_I6400:
+	case CPU_I6500:
+		/* There's no way to disable the FTLB */
+		if (!(flags & FTLB_EN))
+			return 1;
+		return 0;
+	case CPU_LOONGSON64:
+		/* Flush ITLB, DTLB, VTLB and FTLB */
+		write_c0_diag(LOONGSON_DIAG_ITLB | LOONGSON_DIAG_DTLB |
+			      LOONGSON_DIAG_VTLB | LOONGSON_DIAG_FTLB);
+		/* Loongson-3 cores use Config6 to enable the FTLB */
+		config = read_c0_config6();
+		if (flags & FTLB_EN)
+			/* Enable FTLB */
+			write_c0_config6(config & ~LOONGSON_CONF6_FTLBDIS);
+		else
+			/* Disable FTLB */
+			write_c0_config6(config | LOONGSON_CONF6_FTLBDIS);
+		break;
+	default:
+		return 1;
+	}
+
+	return 0;
+}
+
+static int mm_config(struct cpuinfo_mips *c)
+{
+	unsigned int config0, update, mm;
+
+	config0 = read_c0_config();
+	mm = config0 & MIPS_CONF_MM;
+
+	/*
+	 * It's implementation dependent what type of write-merge is supported
+	 * and whether it can be enabled/disabled. If it is settable lets make
+	 * the merging allowed by default. Some platforms might have
+	 * write-through caching unsupported. In this case just ignore the
+	 * CP0.Config.MM bit field value.
+	 */
+	switch (c->cputype) {
+	case CPU_24K:
+	case CPU_34K:
+	case CPU_74K:
+	case CPU_P5600:
+	case CPU_P6600:
+		c->options |= MIPS_CPU_MM_FULL;
+		update = MIPS_CONF_MM_FULL;
+		break;
+	case CPU_1004K:
+	case CPU_1074K:
+	case CPU_INTERAPTIV:
+	case CPU_PROAPTIV:
+		mm = 0;
+		fallthrough;
+	default:
+		update = 0;
+		break;
+	}
+
+	if (update) {
+		config0 = (config0 & ~MIPS_CONF_MM) | update;
+		write_c0_config(config0);
+	} else if (mm == MIPS_CONF_MM_SYSAD) {
+		c->options |= MIPS_CPU_MM_SYSAD;
+	} else if (mm == MIPS_CONF_MM_FULL) {
+		c->options |= MIPS_CPU_MM_FULL;
+	}
+
+	return 0;
+}
+
+static inline unsigned int decode_config0(struct cpuinfo_mips *c)
+{
+	unsigned int config0;
+	int isa, mt;
+
+	config0 = read_c0_config();
+
+	/*
+	 * Look for Standard TLB or Dual VTLB and FTLB
+	 */
+	mt = config0 & MIPS_CONF_MT;
+	if (mt == MIPS_CONF_MT_TLB)
+		c->options |= MIPS_CPU_TLB;
+	else if (mt == MIPS_CONF_MT_FTLB)
+		c->options |= MIPS_CPU_TLB | MIPS_CPU_FTLB;
+
+	isa = (config0 & MIPS_CONF_AT) >> 13;
+	switch (isa) {
+	case 0:
+		switch ((config0 & MIPS_CONF_AR) >> 10) {
+		case 0:
+			set_isa(c, MIPS_CPU_ISA_M32R1);
+			break;
+		case 1:
+			set_isa(c, MIPS_CPU_ISA_M32R2);
+			break;
+		case 2:
+			set_isa(c, MIPS_CPU_ISA_M32R6);
+			break;
+		default:
+			goto unknown;
+		}
+		break;
+	case 2:
+		switch ((config0 & MIPS_CONF_AR) >> 10) {
+		case 0:
+			set_isa(c, MIPS_CPU_ISA_M64R1);
+			break;
+		case 1:
+			set_isa(c, MIPS_CPU_ISA_M64R2);
+			break;
+		case 2:
+			set_isa(c, MIPS_CPU_ISA_M64R6);
+			break;
+		default:
+			goto unknown;
+		}
+		break;
+	default:
+		goto unknown;
+	}
+
+	return config0 & MIPS_CONF_M;
+
+unknown:
+	panic(unknown_isa, config0);
+}
+
+static inline unsigned int decode_config1(struct cpuinfo_mips *c)
+{
+	unsigned int config1;
+
+	config1 = read_c0_config1();
+
+	if (config1 & MIPS_CONF1_MD)
+		c->ases |= MIPS_ASE_MDMX;
+	if (config1 & MIPS_CONF1_PC)
+		c->options |= MIPS_CPU_PERF;
+	if (config1 & MIPS_CONF1_WR)
+		c->options |= MIPS_CPU_WATCH;
+	if (config1 & MIPS_CONF1_CA)
+		c->ases |= MIPS_ASE_MIPS16;
+	if (config1 & MIPS_CONF1_EP)
+		c->options |= MIPS_CPU_EJTAG;
+	if (config1 & MIPS_CONF1_FP) {
+		c->options |= MIPS_CPU_FPU;
+		c->options |= MIPS_CPU_32FPR;
+	}
+	if (cpu_has_tlb) {
+		c->tlbsize = ((config1 & MIPS_CONF1_TLBS) >> 25) + 1;
+		c->tlbsizevtlb = c->tlbsize;
+		c->tlbsizeftlbsets = 0;
+	}
+
+	return config1 & MIPS_CONF_M;
+}
+
+static inline unsigned int decode_config2(struct cpuinfo_mips *c)
+{
+	unsigned int config2;
+
+	config2 = read_c0_config2();
+
+	if (config2 & MIPS_CONF2_SL)
+		c->scache.flags &= ~MIPS_CACHE_NOT_PRESENT;
+
+	return config2 & MIPS_CONF_M;
+}
+
+static inline unsigned int decode_config3(struct cpuinfo_mips *c)
+{
+	unsigned int config3;
+
+	config3 = read_c0_config3();
+
+	if (config3 & MIPS_CONF3_SM) {
+		c->ases |= MIPS_ASE_SMARTMIPS;
+		c->options |= MIPS_CPU_RIXI | MIPS_CPU_CTXTC;
+	}
+	if (config3 & MIPS_CONF3_RXI)
+		c->options |= MIPS_CPU_RIXI;
+	if (config3 & MIPS_CONF3_CTXTC)
+		c->options |= MIPS_CPU_CTXTC;
+	if (config3 & MIPS_CONF3_DSP)
+		c->ases |= MIPS_ASE_DSP;
+	if (config3 & MIPS_CONF3_DSP2P) {
+		c->ases |= MIPS_ASE_DSP2P;
+		if (cpu_has_mips_r6)
+			c->ases |= MIPS_ASE_DSP3;
+	}
+	if (config3 & MIPS_CONF3_VINT)
+		c->options |= MIPS_CPU_VINT;
+	if (config3 & MIPS_CONF3_VEIC)
+		c->options |= MIPS_CPU_VEIC;
+	if (config3 & MIPS_CONF3_LPA)
+		c->options |= MIPS_CPU_LPA;
+	if (config3 & MIPS_CONF3_MT)
+		c->ases |= MIPS_ASE_MIPSMT;
+	if (config3 & MIPS_CONF3_ULRI)
+		c->options |= MIPS_CPU_ULRI;
+	if (config3 & MIPS_CONF3_ISA)
+		c->options |= MIPS_CPU_MICROMIPS;
+	if (config3 & MIPS_CONF3_VZ)
+		c->ases |= MIPS_ASE_VZ;
+	if (config3 & MIPS_CONF3_SC)
+		c->options |= MIPS_CPU_SEGMENTS;
+	if (config3 & MIPS_CONF3_BI)
+		c->options |= MIPS_CPU_BADINSTR;
+	if (config3 & MIPS_CONF3_BP)
+		c->options |= MIPS_CPU_BADINSTRP;
+	if (config3 & MIPS_CONF3_MSA)
+		c->ases |= MIPS_ASE_MSA;
+	if (config3 & MIPS_CONF3_PW) {
+		c->htw_seq = 0;
+		c->options |= MIPS_CPU_HTW;
+	}
+	if (config3 & MIPS_CONF3_CDMM)
+		c->options |= MIPS_CPU_CDMM;
+	if (config3 & MIPS_CONF3_SP)
+		c->options |= MIPS_CPU_SP;
+
+	return config3 & MIPS_CONF_M;
+}
+
+static inline unsigned int decode_config4(struct cpuinfo_mips *c)
+{
+	unsigned int config4;
+	unsigned int newcf4;
+	unsigned int mmuextdef;
+	unsigned int ftlb_page = MIPS_CONF4_FTLBPAGESIZE;
+	unsigned long asid_mask;
+
+	config4 = read_c0_config4();
+
+	if (cpu_has_tlb) {
+		if (((config4 & MIPS_CONF4_IE) >> 29) == 2)
+			c->options |= MIPS_CPU_TLBINV;
+
+		/*
+		 * R6 has dropped the MMUExtDef field from config4.
+		 * On R6 the fields always describe the FTLB, and only if it is
+		 * present according to Config.MT.
+		 */
+		if (!cpu_has_mips_r6)
+			mmuextdef = config4 & MIPS_CONF4_MMUEXTDEF;
+		else if (cpu_has_ftlb)
+			mmuextdef = MIPS_CONF4_MMUEXTDEF_VTLBSIZEEXT;
+		else
+			mmuextdef = 0;
+
+		switch (mmuextdef) {
+		case MIPS_CONF4_MMUEXTDEF_MMUSIZEEXT:
+			c->tlbsize += (config4 & MIPS_CONF4_MMUSIZEEXT) * 0x40;
+			c->tlbsizevtlb = c->tlbsize;
+			break;
+		case MIPS_CONF4_MMUEXTDEF_VTLBSIZEEXT:
+			c->tlbsizevtlb +=
+				((config4 & MIPS_CONF4_VTLBSIZEEXT) >>
+				  MIPS_CONF4_VTLBSIZEEXT_SHIFT) * 0x40;
+			c->tlbsize = c->tlbsizevtlb;
+			ftlb_page = MIPS_CONF4_VFTLBPAGESIZE;
+			fallthrough;
+		case MIPS_CONF4_MMUEXTDEF_FTLBSIZEEXT:
+			if (mips_ftlb_disabled)
+				break;
+			newcf4 = (config4 & ~ftlb_page) |
+				(page_size_ftlb(mmuextdef) <<
+				 MIPS_CONF4_FTLBPAGESIZE_SHIFT);
+			write_c0_config4(newcf4);
+			back_to_back_c0_hazard();
+			config4 = read_c0_config4();
+			if (config4 != newcf4) {
+				pr_err("PAGE_SIZE 0x%lx is not supported by FTLB (config4=0x%x)\n",
+				       PAGE_SIZE, config4);
+				/* Switch FTLB off */
+				set_ftlb_enable(c, 0);
+				mips_ftlb_disabled = 1;
+				break;
+			}
+			c->tlbsizeftlbsets = 1 <<
+				((config4 & MIPS_CONF4_FTLBSETS) >>
+				 MIPS_CONF4_FTLBSETS_SHIFT);
+			c->tlbsizeftlbways = ((config4 & MIPS_CONF4_FTLBWAYS) >>
+					      MIPS_CONF4_FTLBWAYS_SHIFT) + 2;
+			c->tlbsize += c->tlbsizeftlbways * c->tlbsizeftlbsets;
+			mips_has_ftlb_configured = 1;
+			break;
+		}
+	}
+
+	c->kscratch_mask = (config4 & MIPS_CONF4_KSCREXIST)
+				>> MIPS_CONF4_KSCREXIST_SHIFT;
+
+	asid_mask = MIPS_ENTRYHI_ASID;
+	if (config4 & MIPS_CONF4_AE)
+		asid_mask |= MIPS_ENTRYHI_ASIDX;
+	set_cpu_asid_mask(c, asid_mask);
+
+	/*
+	 * Warn if the computed ASID mask doesn't match the mask the kernel
+	 * is built for. This may indicate either a serious problem or an
+	 * easy optimisation opportunity, but either way should be addressed.
+	 */
+	WARN_ON(asid_mask != cpu_asid_mask(c));
+
+	return config4 & MIPS_CONF_M;
+}
+
+static inline unsigned int decode_config5(struct cpuinfo_mips *c)
+{
+	unsigned int config5, max_mmid_width;
+	unsigned long asid_mask;
+
+	config5 = read_c0_config5();
+	config5 &= ~(MIPS_CONF5_UFR | MIPS_CONF5_UFE);
+
+	if (cpu_has_mips_r6) {
+		if (!__builtin_constant_p(cpu_has_mmid) || cpu_has_mmid)
+			config5 |= MIPS_CONF5_MI;
+		else
+			config5 &= ~MIPS_CONF5_MI;
+	}
+
+	write_c0_config5(config5);
+
+	if (config5 & MIPS_CONF5_EVA)
+		c->options |= MIPS_CPU_EVA;
+	if (config5 & MIPS_CONF5_MRP)
+		c->options |= MIPS_CPU_MAAR;
+	if (config5 & MIPS_CONF5_LLB)
+		c->options |= MIPS_CPU_RW_LLB;
+	if (config5 & MIPS_CONF5_MVH)
+		c->options |= MIPS_CPU_MVH;
+	if (cpu_has_mips_r6 && (config5 & MIPS_CONF5_VP))
+		c->options |= MIPS_CPU_VP;
+	if (config5 & MIPS_CONF5_CA2)
+		c->ases |= MIPS_ASE_MIPS16E2;
+
+	if (config5 & MIPS_CONF5_CRCP)
+		elf_hwcap |= HWCAP_MIPS_CRC32;
+
+	if (cpu_has_mips_r6) {
+		/* Ensure the write to config5 above takes effect */
+		back_to_back_c0_hazard();
+
+		/* Check whether we successfully enabled MMID support */
+		config5 = read_c0_config5();
+		if (config5 & MIPS_CONF5_MI)
+			c->options |= MIPS_CPU_MMID;
+
+		/*
+		 * Warn if we've hardcoded cpu_has_mmid to a value unsuitable
+		 * for the CPU we're running on, or if CPUs in an SMP system
+		 * have inconsistent MMID support.
+		 */
+		WARN_ON(!!cpu_has_mmid != !!(config5 & MIPS_CONF5_MI));
+
+		if (cpu_has_mmid) {
+			write_c0_memorymapid(~0ul);
+			back_to_back_c0_hazard();
+			asid_mask = read_c0_memorymapid();
+
+			/*
+			 * We maintain a bitmap to track MMID allocation, and
+			 * need a sensible upper bound on the size of that
+			 * bitmap. The initial CPU with MMID support (I6500)
+			 * supports 16 bit MMIDs, which gives us an 8KiB
+			 * bitmap. The architecture recommends that hardware
+			 * support 32 bit MMIDs, which would give us a 512MiB
+			 * bitmap - that's too big in most cases.
+			 *
+			 * Cap MMID width at 16 bits for now & we can revisit
+			 * this if & when hardware supports anything wider.
+			 */
+			max_mmid_width = 16;
+			if (asid_mask > GENMASK(max_mmid_width - 1, 0)) {
+				pr_info("Capping MMID width at %d bits",
+					max_mmid_width);
+				asid_mask = GENMASK(max_mmid_width - 1, 0);
+			}
+
+			set_cpu_asid_mask(c, asid_mask);
+		}
+	}
+
+	return config5 & MIPS_CONF_M;
+}
+
+static void decode_configs(struct cpuinfo_mips *c)
+{
+	int ok;
+
+	/* MIPS32 or MIPS64 compliant CPU.  */
+	c->options = MIPS_CPU_4KEX | MIPS_CPU_4K_CACHE | MIPS_CPU_COUNTER |
+		     MIPS_CPU_DIVEC | MIPS_CPU_LLSC | MIPS_CPU_MCHECK;
+
+	c->scache.flags = MIPS_CACHE_NOT_PRESENT;
+
+	/* Enable FTLB if present and not disabled */
+	set_ftlb_enable(c, mips_ftlb_disabled ? 0 : FTLB_EN);
+
+	ok = decode_config0(c);			/* Read Config registers.  */
+	BUG_ON(!ok);				/* Arch spec violation!	 */
+	if (ok)
+		ok = decode_config1(c);
+	if (ok)
+		ok = decode_config2(c);
+	if (ok)
+		ok = decode_config3(c);
+	if (ok)
+		ok = decode_config4(c);
+	if (ok)
+		ok = decode_config5(c);
+
+	/* Probe the EBase.WG bit */
+	if (cpu_has_mips_r2_r6) {
+		u64 ebase;
+		unsigned int status;
+
+		/* {read,write}_c0_ebase_64() may be UNDEFINED prior to r6 */
+		ebase = cpu_has_mips64r6 ? read_c0_ebase_64()
+					 : (s32)read_c0_ebase();
+		if (ebase & MIPS_EBASE_WG) {
+			/* WG bit already set, we can avoid the clumsy probe */
+			c->options |= MIPS_CPU_EBASE_WG;
+		} else {
+			/* Its UNDEFINED to change EBase while BEV=0 */
+			status = read_c0_status();
+			write_c0_status(status | ST0_BEV);
+			irq_enable_hazard();
+			/*
+			 * On pre-r6 cores, this may well clobber the upper bits
+			 * of EBase. This is hard to avoid without potentially
+			 * hitting UNDEFINED dm*c0 behaviour if EBase is 32-bit.
+			 */
+			if (cpu_has_mips64r6)
+				write_c0_ebase_64(ebase | MIPS_EBASE_WG);
+			else
+				write_c0_ebase(ebase | MIPS_EBASE_WG);
+			back_to_back_c0_hazard();
+			/* Restore BEV */
+			write_c0_status(status);
+			if (read_c0_ebase() & MIPS_EBASE_WG) {
+				c->options |= MIPS_CPU_EBASE_WG;
+				write_c0_ebase(ebase);
+			}
+		}
+	}
+
+	/* configure the FTLB write probability */
+	set_ftlb_enable(c, (mips_ftlb_disabled ? 0 : FTLB_EN) | FTLB_SET_PROB);
+
+	mips_probe_watch_registers(c);
+
+#ifndef CONFIG_MIPS_CPS
+	if (cpu_has_mips_r2_r6) {
+		unsigned int core;
+
+		core = get_ebase_cpunum();
+		if (cpu_has_mipsmt)
+			core >>= fls(core_nvpes()) - 1;
+		cpu_set_core(c, core);
+	}
+#endif
+}
+
+/*
+ * Probe for certain guest capabilities by writing config bits and reading back.
+ * Finally write back the original value.
+ */
+#define probe_gc0_config(name, maxconf, bits)				\
+do {									\
+	unsigned int tmp;						\
+	tmp = read_gc0_##name();					\
+	write_gc0_##name(tmp | (bits));					\
+	back_to_back_c0_hazard();					\
+	maxconf = read_gc0_##name();					\
+	write_gc0_##name(tmp);						\
+} while (0)
+
+/*
+ * Probe for dynamic guest capabilities by changing certain config bits and
+ * reading back to see if they change. Finally write back the original value.
+ */
+#define probe_gc0_config_dyn(name, maxconf, dynconf, bits)		\
+do {									\
+	maxconf = read_gc0_##name();					\
+	write_gc0_##name(maxconf ^ (bits));				\
+	back_to_back_c0_hazard();					\
+	dynconf = maxconf ^ read_gc0_##name();				\
+	write_gc0_##name(maxconf);					\
+	maxconf |= dynconf;						\
+} while (0)
+
+static inline unsigned int decode_guest_config0(struct cpuinfo_mips *c)
+{
+	unsigned int config0;
+
+	probe_gc0_config(config, config0, MIPS_CONF_M);
+
+	if (config0 & MIPS_CONF_M)
+		c->guest.conf |= BIT(1);
+	return config0 & MIPS_CONF_M;
+}
+
+static inline unsigned int decode_guest_config1(struct cpuinfo_mips *c)
+{
+	unsigned int config1, config1_dyn;
+
+	probe_gc0_config_dyn(config1, config1, config1_dyn,
+			     MIPS_CONF_M | MIPS_CONF1_PC | MIPS_CONF1_WR |
+			     MIPS_CONF1_FP);
+
+	if (config1 & MIPS_CONF1_FP)
+		c->guest.options |= MIPS_CPU_FPU;
+	if (config1_dyn & MIPS_CONF1_FP)
+		c->guest.options_dyn |= MIPS_CPU_FPU;
+
+	if (config1 & MIPS_CONF1_WR)
+		c->guest.options |= MIPS_CPU_WATCH;
+	if (config1_dyn & MIPS_CONF1_WR)
+		c->guest.options_dyn |= MIPS_CPU_WATCH;
+
+	if (config1 & MIPS_CONF1_PC)
+		c->guest.options |= MIPS_CPU_PERF;
+	if (config1_dyn & MIPS_CONF1_PC)
+		c->guest.options_dyn |= MIPS_CPU_PERF;
+
+	if (config1 & MIPS_CONF_M)
+		c->guest.conf |= BIT(2);
+	return config1 & MIPS_CONF_M;
+}
+
+static inline unsigned int decode_guest_config2(struct cpuinfo_mips *c)
+{
+	unsigned int config2;
+
+	probe_gc0_config(config2, config2, MIPS_CONF_M);
+
+	if (config2 & MIPS_CONF_M)
+		c->guest.conf |= BIT(3);
+	return config2 & MIPS_CONF_M;
+}
+
+static inline unsigned int decode_guest_config3(struct cpuinfo_mips *c)
+{
+	unsigned int config3, config3_dyn;
+
+	probe_gc0_config_dyn(config3, config3, config3_dyn,
+			     MIPS_CONF_M | MIPS_CONF3_MSA | MIPS_CONF3_ULRI |
+			     MIPS_CONF3_CTXTC);
+
+	if (config3 & MIPS_CONF3_CTXTC)
+		c->guest.options |= MIPS_CPU_CTXTC;
+	if (config3_dyn & MIPS_CONF3_CTXTC)
+		c->guest.options_dyn |= MIPS_CPU_CTXTC;
+
+	if (config3 & MIPS_CONF3_PW)
+		c->guest.options |= MIPS_CPU_HTW;
+
+	if (config3 & MIPS_CONF3_ULRI)
+		c->guest.options |= MIPS_CPU_ULRI;
+
+	if (config3 & MIPS_CONF3_SC)
+		c->guest.options |= MIPS_CPU_SEGMENTS;
+
+	if (config3 & MIPS_CONF3_BI)
+		c->guest.options |= MIPS_CPU_BADINSTR;
+	if (config3 & MIPS_CONF3_BP)
+		c->guest.options |= MIPS_CPU_BADINSTRP;
+
+	if (config3 & MIPS_CONF3_MSA)
+		c->guest.ases |= MIPS_ASE_MSA;
+	if (config3_dyn & MIPS_CONF3_MSA)
+		c->guest.ases_dyn |= MIPS_ASE_MSA;
+
+	if (config3 & MIPS_CONF_M)
+		c->guest.conf |= BIT(4);
+	return config3 & MIPS_CONF_M;
+}
+
+static inline unsigned int decode_guest_config4(struct cpuinfo_mips *c)
+{
+	unsigned int config4;
+
+	probe_gc0_config(config4, config4,
+			 MIPS_CONF_M | MIPS_CONF4_KSCREXIST);
+
+	c->guest.kscratch_mask = (config4 & MIPS_CONF4_KSCREXIST)
+				>> MIPS_CONF4_KSCREXIST_SHIFT;
+
+	if (config4 & MIPS_CONF_M)
+		c->guest.conf |= BIT(5);
+	return config4 & MIPS_CONF_M;
+}
+
+static inline unsigned int decode_guest_config5(struct cpuinfo_mips *c)
+{
+	unsigned int config5, config5_dyn;
+
+	probe_gc0_config_dyn(config5, config5, config5_dyn,
+			 MIPS_CONF_M | MIPS_CONF5_MVH | MIPS_CONF5_MRP);
+
+	if (config5 & MIPS_CONF5_MRP)
+		c->guest.options |= MIPS_CPU_MAAR;
+	if (config5_dyn & MIPS_CONF5_MRP)
+		c->guest.options_dyn |= MIPS_CPU_MAAR;
+
+	if (config5 & MIPS_CONF5_LLB)
+		c->guest.options |= MIPS_CPU_RW_LLB;
+
+	if (config5 & MIPS_CONF5_MVH)
+		c->guest.options |= MIPS_CPU_MVH;
+
+	if (config5 & MIPS_CONF_M)
+		c->guest.conf |= BIT(6);
+	return config5 & MIPS_CONF_M;
+}
+
+static inline void decode_guest_configs(struct cpuinfo_mips *c)
+{
+	unsigned int ok;
+
+	ok = decode_guest_config0(c);
+	if (ok)
+		ok = decode_guest_config1(c);
+	if (ok)
+		ok = decode_guest_config2(c);
+	if (ok)
+		ok = decode_guest_config3(c);
+	if (ok)
+		ok = decode_guest_config4(c);
+	if (ok)
+		decode_guest_config5(c);
+}
+
+static inline void cpu_probe_guestctl0(struct cpuinfo_mips *c)
+{
+	unsigned int guestctl0, temp;
+
+	guestctl0 = read_c0_guestctl0();
+
+	if (guestctl0 & MIPS_GCTL0_G0E)
+		c->options |= MIPS_CPU_GUESTCTL0EXT;
+	if (guestctl0 & MIPS_GCTL0_G1)
+		c->options |= MIPS_CPU_GUESTCTL1;
+	if (guestctl0 & MIPS_GCTL0_G2)
+		c->options |= MIPS_CPU_GUESTCTL2;
+	if (!(guestctl0 & MIPS_GCTL0_RAD)) {
+		c->options |= MIPS_CPU_GUESTID;
+
+		/*
+		 * Probe for Direct Root to Guest (DRG). Set GuestCtl1.RID = 0
+		 * first, otherwise all data accesses will be fully virtualised
+		 * as if they were performed by guest mode.
+		 */
+		write_c0_guestctl1(0);
+		tlbw_use_hazard();
+
+		write_c0_guestctl0(guestctl0 | MIPS_GCTL0_DRG);
+		back_to_back_c0_hazard();
+		temp = read_c0_guestctl0();
+
+		if (temp & MIPS_GCTL0_DRG) {
+			write_c0_guestctl0(guestctl0);
+			c->options |= MIPS_CPU_DRG;
+		}
+	}
+}
+
+static inline void cpu_probe_guestctl1(struct cpuinfo_mips *c)
+{
+	if (cpu_has_guestid) {
+		/* determine the number of bits of GuestID available */
+		write_c0_guestctl1(MIPS_GCTL1_ID);
+		back_to_back_c0_hazard();
+		c->guestid_mask = (read_c0_guestctl1() & MIPS_GCTL1_ID)
+						>> MIPS_GCTL1_ID_SHIFT;
+		write_c0_guestctl1(0);
+	}
+}
+
+static inline void cpu_probe_gtoffset(struct cpuinfo_mips *c)
+{
+	/* determine the number of bits of GTOffset available */
+	write_c0_gtoffset(0xffffffff);
+	back_to_back_c0_hazard();
+	c->gtoffset_mask = read_c0_gtoffset();
+	write_c0_gtoffset(0);
+}
+
+static inline void cpu_probe_vz(struct cpuinfo_mips *c)
+{
+	cpu_probe_guestctl0(c);
+	if (cpu_has_guestctl1)
+		cpu_probe_guestctl1(c);
+
+	cpu_probe_gtoffset(c);
+
+	decode_guest_configs(c);
+}
+
+#define R4K_OPTS (MIPS_CPU_TLB | MIPS_CPU_4KEX | MIPS_CPU_4K_CACHE \
+		| MIPS_CPU_COUNTER)
+
+static inline void cpu_probe_legacy(struct cpuinfo_mips *c, unsigned int cpu)
+{
+	switch (c->processor_id & PRID_IMP_MASK) {
+	case PRID_IMP_R2000:
+		c->cputype = CPU_R2000;
+		__cpu_name[cpu] = "R2000";
+		c->fpu_msk31 |= FPU_CSR_CONDX | FPU_CSR_FS;
+		c->options = MIPS_CPU_TLB | MIPS_CPU_3K_CACHE |
+			     MIPS_CPU_NOFPUEX;
+		if (__cpu_has_fpu())
+			c->options |= MIPS_CPU_FPU;
+		c->tlbsize = 64;
+		break;
+	case PRID_IMP_R3000:
+		if ((c->processor_id & PRID_REV_MASK) == PRID_REV_R3000A) {
+			if (cpu_has_confreg()) {
+				c->cputype = CPU_R3081E;
+				__cpu_name[cpu] = "R3081";
+			} else {
+				c->cputype = CPU_R3000A;
+				__cpu_name[cpu] = "R3000A";
+			}
+		} else {
+			c->cputype = CPU_R3000;
+			__cpu_name[cpu] = "R3000";
+		}
+		c->fpu_msk31 |= FPU_CSR_CONDX | FPU_CSR_FS;
+		c->options = MIPS_CPU_TLB | MIPS_CPU_3K_CACHE |
+			     MIPS_CPU_NOFPUEX;
+		if (__cpu_has_fpu())
+			c->options |= MIPS_CPU_FPU;
+		c->tlbsize = 64;
+		break;
+	case PRID_IMP_R4000:
+		if (read_c0_config() & CONF_SC) {
+			if ((c->processor_id & PRID_REV_MASK) >=
+			    PRID_REV_R4400) {
+				c->cputype = CPU_R4400PC;
+				__cpu_name[cpu] = "R4400PC";
+			} else {
+				c->cputype = CPU_R4000PC;
+				__cpu_name[cpu] = "R4000PC";
+			}
+		} else {
+			int cca = read_c0_config() & CONF_CM_CMASK;
+			int mc;
+
+			/*
+			 * SC and MC versions can't be reliably told apart,
+			 * but only the latter support coherent caching
+			 * modes so assume the firmware has set the KSEG0
+			 * coherency attribute reasonably (if uncached, we
+			 * assume SC).
+			 */
+			switch (cca) {
+			case CONF_CM_CACHABLE_CE:
+			case CONF_CM_CACHABLE_COW:
+			case CONF_CM_CACHABLE_CUW:
+				mc = 1;
+				break;
+			default:
+				mc = 0;
+				break;
+			}
+			if ((c->processor_id & PRID_REV_MASK) >=
+			    PRID_REV_R4400) {
+				c->cputype = mc ? CPU_R4400MC : CPU_R4400SC;
+				__cpu_name[cpu] = mc ? "R4400MC" : "R4400SC";
+			} else {
+				c->cputype = mc ? CPU_R4000MC : CPU_R4000SC;
+				__cpu_name[cpu] = mc ? "R4000MC" : "R4000SC";
+			}
+		}
+
+		set_isa(c, MIPS_CPU_ISA_III);
+		c->fpu_msk31 |= FPU_CSR_CONDX;
+		c->options = R4K_OPTS | MIPS_CPU_FPU | MIPS_CPU_32FPR |
+			     MIPS_CPU_WATCH | MIPS_CPU_VCE |
+			     MIPS_CPU_LLSC;
+		c->tlbsize = 48;
+		break;
+	case PRID_IMP_R4300:
+		c->cputype = CPU_R4300;
+		__cpu_name[cpu] = "R4300";
+		set_isa(c, MIPS_CPU_ISA_III);
+		c->fpu_msk31 |= FPU_CSR_CONDX;
+		c->options = R4K_OPTS | MIPS_CPU_FPU | MIPS_CPU_32FPR |
+			     MIPS_CPU_LLSC;
+		c->tlbsize = 32;
+		break;
+	case PRID_IMP_R4600:
+		c->cputype = CPU_R4600;
+		__cpu_name[cpu] = "R4600";
+		set_isa(c, MIPS_CPU_ISA_III);
+		c->fpu_msk31 |= FPU_CSR_CONDX;
+		c->options = R4K_OPTS | MIPS_CPU_FPU | MIPS_CPU_32FPR |
+			     MIPS_CPU_LLSC;
+		c->tlbsize = 48;
+		break;
+	#if 0
+	case PRID_IMP_R4650:
+		/*
+		 * This processor doesn't have an MMU, so it's not
+		 * "real easy" to run Linux on it. It is left purely
+		 * for documentation.  Commented out because it shares
+		 * it's c0_prid id number with the TX3900.
+		 */
+		c->cputype = CPU_R4650;
+		__cpu_name[cpu] = "R4650";
+		set_isa(c, MIPS_CPU_ISA_III);
+		c->fpu_msk31 |= FPU_CSR_CONDX;
+		c->options = R4K_OPTS | MIPS_CPU_FPU | MIPS_CPU_LLSC;
+		c->tlbsize = 48;
+		break;
+	#endif
+	case PRID_IMP_R4700:
+		c->cputype = CPU_R4700;
+		__cpu_name[cpu] = "R4700";
+		set_isa(c, MIPS_CPU_ISA_III);
+		c->fpu_msk31 |= FPU_CSR_CONDX;
+		c->options = R4K_OPTS | MIPS_CPU_FPU | MIPS_CPU_32FPR |
+			     MIPS_CPU_LLSC;
+		c->tlbsize = 48;
+		break;
+	case PRID_IMP_TX49:
+		c->cputype = CPU_TX49XX;
+		__cpu_name[cpu] = "R49XX";
+		set_isa(c, MIPS_CPU_ISA_III);
+		c->fpu_msk31 |= FPU_CSR_CONDX;
+		c->options = R4K_OPTS | MIPS_CPU_LLSC;
+		if (!(c->processor_id & 0x08))
+			c->options |= MIPS_CPU_FPU | MIPS_CPU_32FPR;
+		c->tlbsize = 48;
+		break;
+	case PRID_IMP_R5000:
+		c->cputype = CPU_R5000;
+		__cpu_name[cpu] = "R5000";
+		set_isa(c, MIPS_CPU_ISA_IV);
+		c->options = R4K_OPTS | MIPS_CPU_FPU | MIPS_CPU_32FPR |
+			     MIPS_CPU_LLSC;
+		c->tlbsize = 48;
+		break;
+	case PRID_IMP_R5500:
+		c->cputype = CPU_R5500;
+		__cpu_name[cpu] = "R5500";
+		set_isa(c, MIPS_CPU_ISA_IV);
+		c->options = R4K_OPTS | MIPS_CPU_FPU | MIPS_CPU_32FPR |
+			     MIPS_CPU_WATCH | MIPS_CPU_LLSC;
+		c->tlbsize = 48;
+		break;
+	case PRID_IMP_NEVADA:
+		c->cputype = CPU_NEVADA;
+		__cpu_name[cpu] = "Nevada";
+		set_isa(c, MIPS_CPU_ISA_IV);
+		c->options = R4K_OPTS | MIPS_CPU_FPU | MIPS_CPU_32FPR |
+			     MIPS_CPU_DIVEC | MIPS_CPU_LLSC;
+		c->tlbsize = 48;
+		break;
+	case PRID_IMP_RM7000:
+		c->cputype = CPU_RM7000;
+		__cpu_name[cpu] = "RM7000";
+		set_isa(c, MIPS_CPU_ISA_IV);
+		c->options = R4K_OPTS | MIPS_CPU_FPU | MIPS_CPU_32FPR |
+			     MIPS_CPU_LLSC;
+		/*
+		 * Undocumented RM7000:	 Bit 29 in the info register of
+		 * the RM7000 v2.0 indicates if the TLB has 48 or 64
+		 * entries.
+		 *
+		 * 29	   1 =>	   64 entry JTLB
+		 *	   0 =>	   48 entry JTLB
+		 */
+		c->tlbsize = (read_c0_info() & (1 << 29)) ? 64 : 48;
+		break;
+	case PRID_IMP_R10000:
+		c->cputype = CPU_R10000;
+		__cpu_name[cpu] = "R10000";
+		set_isa(c, MIPS_CPU_ISA_IV);
+		c->options = MIPS_CPU_TLB | MIPS_CPU_4K_CACHE | MIPS_CPU_4KEX |
+			     MIPS_CPU_FPU | MIPS_CPU_32FPR |
+			     MIPS_CPU_COUNTER | MIPS_CPU_WATCH |
+			     MIPS_CPU_LLSC;
+		c->tlbsize = 64;
+		break;
+	case PRID_IMP_R12000:
+		c->cputype = CPU_R12000;
+		__cpu_name[cpu] = "R12000";
+		set_isa(c, MIPS_CPU_ISA_IV);
+		c->options = MIPS_CPU_TLB | MIPS_CPU_4K_CACHE | MIPS_CPU_4KEX |
+			     MIPS_CPU_FPU | MIPS_CPU_32FPR |
+			     MIPS_CPU_COUNTER | MIPS_CPU_WATCH |
+			     MIPS_CPU_LLSC;
+		c->tlbsize = 64;
+		write_c0_r10k_diag(read_c0_r10k_diag() | R10K_DIAG_E_GHIST);
+		break;
+	case PRID_IMP_R14000:
+		if (((c->processor_id >> 4) & 0x0f) > 2) {
+			c->cputype = CPU_R16000;
+			__cpu_name[cpu] = "R16000";
+		} else {
+			c->cputype = CPU_R14000;
+			__cpu_name[cpu] = "R14000";
+		}
+		set_isa(c, MIPS_CPU_ISA_IV);
+		c->options = MIPS_CPU_TLB | MIPS_CPU_4K_CACHE | MIPS_CPU_4KEX |
+			     MIPS_CPU_FPU | MIPS_CPU_32FPR |
+			     MIPS_CPU_COUNTER | MIPS_CPU_WATCH |
+			     MIPS_CPU_LLSC;
+		c->tlbsize = 64;
+		write_c0_r10k_diag(read_c0_r10k_diag() | R10K_DIAG_E_GHIST);
+		break;
+	case PRID_IMP_LOONGSON_64C:  /* Loongson-2/3 */
+		switch (c->processor_id & PRID_REV_MASK) {
+		case PRID_REV_LOONGSON2E:
+			c->cputype = CPU_LOONGSON2EF;
+			__cpu_name[cpu] = "ICT Loongson-2";
+			set_elf_platform(cpu, "loongson2e");
+			set_isa(c, MIPS_CPU_ISA_III);
+			c->fpu_msk31 |= FPU_CSR_CONDX;
+			break;
+		case PRID_REV_LOONGSON2F:
+			c->cputype = CPU_LOONGSON2EF;
+			__cpu_name[cpu] = "ICT Loongson-2";
+			set_elf_platform(cpu, "loongson2f");
+			set_isa(c, MIPS_CPU_ISA_III);
+			c->fpu_msk31 |= FPU_CSR_CONDX;
+			break;
+		case PRID_REV_LOONGSON3A_R1:
+			c->cputype = CPU_LOONGSON64;
+			__cpu_name[cpu] = "ICT Loongson-3";
+			set_elf_platform(cpu, "loongson3a");
+			set_isa(c, MIPS_CPU_ISA_M64R1);
+			c->ases |= (MIPS_ASE_LOONGSON_MMI | MIPS_ASE_LOONGSON_CAM |
+				MIPS_ASE_LOONGSON_EXT);
+			break;
+		case PRID_REV_LOONGSON3B_R1:
+		case PRID_REV_LOONGSON3B_R2:
+			c->cputype = CPU_LOONGSON64;
+			__cpu_name[cpu] = "ICT Loongson-3";
+			set_elf_platform(cpu, "loongson3b");
+			set_isa(c, MIPS_CPU_ISA_M64R1);
+			c->ases |= (MIPS_ASE_LOONGSON_MMI | MIPS_ASE_LOONGSON_CAM |
+				MIPS_ASE_LOONGSON_EXT);
+			break;
+		}
+
+		c->options = R4K_OPTS |
+			     MIPS_CPU_FPU | MIPS_CPU_LLSC |
+			     MIPS_CPU_32FPR;
+		c->tlbsize = 64;
+		set_cpu_asid_mask(c, MIPS_ENTRYHI_ASID);
+		c->writecombine = _CACHE_UNCACHED_ACCELERATED;
+		break;
+	case PRID_IMP_LOONGSON_32:  /* Loongson-1 */
+		decode_configs(c);
+
+		c->cputype = CPU_LOONGSON32;
+
+		switch (c->processor_id & PRID_REV_MASK) {
+		case PRID_REV_LOONGSON1B:
+			__cpu_name[cpu] = "Loongson 1B";
+			break;
+		}
+
+		break;
+	}
+}
+
+static inline void cpu_probe_mips(struct cpuinfo_mips *c, unsigned int cpu)
+{
+	c->writecombine = _CACHE_UNCACHED_ACCELERATED;
+	switch (c->processor_id & PRID_IMP_MASK) {
+	case PRID_IMP_QEMU_GENERIC:
+		c->writecombine = _CACHE_UNCACHED;
+		c->cputype = CPU_QEMU_GENERIC;
+		__cpu_name[cpu] = "MIPS GENERIC QEMU";
+		break;
+	case PRID_IMP_4KC:
+		c->cputype = CPU_4KC;
+		c->writecombine = _CACHE_UNCACHED;
+		__cpu_name[cpu] = "MIPS 4Kc";
+		break;
+	case PRID_IMP_4KEC:
+	case PRID_IMP_4KECR2:
+		c->cputype = CPU_4KEC;
+		c->writecombine = _CACHE_UNCACHED;
+		__cpu_name[cpu] = "MIPS 4KEc";
+		break;
+	case PRID_IMP_4KSC:
+	case PRID_IMP_4KSD:
+		c->cputype = CPU_4KSC;
+		c->writecombine = _CACHE_UNCACHED;
+		__cpu_name[cpu] = "MIPS 4KSc";
+		break;
+	case PRID_IMP_5KC:
+		c->cputype = CPU_5KC;
+		c->writecombine = _CACHE_UNCACHED;
+		__cpu_name[cpu] = "MIPS 5Kc";
+		break;
+	case PRID_IMP_5KE:
+		c->cputype = CPU_5KE;
+		c->writecombine = _CACHE_UNCACHED;
+		__cpu_name[cpu] = "MIPS 5KE";
+		break;
+	case PRID_IMP_20KC:
+		c->cputype = CPU_20KC;
+		c->writecombine = _CACHE_UNCACHED;
+		__cpu_name[cpu] = "MIPS 20Kc";
+		break;
+	case PRID_IMP_24K:
+		c->cputype = CPU_24K;
+		c->writecombine = _CACHE_UNCACHED;
+		__cpu_name[cpu] = "MIPS 24Kc";
+		break;
+	case PRID_IMP_24KE:
+		c->cputype = CPU_24K;
+		c->writecombine = _CACHE_UNCACHED;
+		__cpu_name[cpu] = "MIPS 24KEc";
+		break;
+	case PRID_IMP_25KF:
+		c->cputype = CPU_25KF;
+		c->writecombine = _CACHE_UNCACHED;
+		__cpu_name[cpu] = "MIPS 25Kc";
+		break;
+	case PRID_IMP_34K:
+		c->cputype = CPU_34K;
+		c->writecombine = _CACHE_UNCACHED;
+		__cpu_name[cpu] = "MIPS 34Kc";
+		cpu_set_mt_per_tc_perf(c);
+		break;
+	case PRID_IMP_74K:
+		c->cputype = CPU_74K;
+		c->writecombine = _CACHE_UNCACHED;
+		__cpu_name[cpu] = "MIPS 74Kc";
+		break;
+	case PRID_IMP_M14KC:
+		c->cputype = CPU_M14KC;
+		c->writecombine = _CACHE_UNCACHED;
+		__cpu_name[cpu] = "MIPS M14Kc";
+		break;
+	case PRID_IMP_M14KEC:
+		c->cputype = CPU_M14KEC;
+		c->writecombine = _CACHE_UNCACHED;
+		__cpu_name[cpu] = "MIPS M14KEc";
+		break;
+	case PRID_IMP_1004K:
+		c->cputype = CPU_1004K;
+		c->writecombine = _CACHE_UNCACHED;
+		__cpu_name[cpu] = "MIPS 1004Kc";
+		cpu_set_mt_per_tc_perf(c);
+		break;
+	case PRID_IMP_1074K:
+		c->cputype = CPU_1074K;
+		c->writecombine = _CACHE_UNCACHED;
+		__cpu_name[cpu] = "MIPS 1074Kc";
+		break;
+	case PRID_IMP_INTERAPTIV_UP:
+		c->cputype = CPU_INTERAPTIV;
+		__cpu_name[cpu] = "MIPS interAptiv";
+		cpu_set_mt_per_tc_perf(c);
+		break;
+	case PRID_IMP_INTERAPTIV_MP:
+		c->cputype = CPU_INTERAPTIV;
+		__cpu_name[cpu] = "MIPS interAptiv (multi)";
+		cpu_set_mt_per_tc_perf(c);
+		break;
+	case PRID_IMP_PROAPTIV_UP:
+		c->cputype = CPU_PROAPTIV;
+		__cpu_name[cpu] = "MIPS proAptiv";
+		break;
+	case PRID_IMP_PROAPTIV_MP:
+		c->cputype = CPU_PROAPTIV;
+		__cpu_name[cpu] = "MIPS proAptiv (multi)";
+		break;
+	case PRID_IMP_P5600:
+		c->cputype = CPU_P5600;
+		__cpu_name[cpu] = "MIPS P5600";
+		break;
+	case PRID_IMP_P6600:
+		c->cputype = CPU_P6600;
+		__cpu_name[cpu] = "MIPS P6600";
+		break;
+	case PRID_IMP_I6400:
+		c->cputype = CPU_I6400;
+		__cpu_name[cpu] = "MIPS I6400";
+		break;
+	case PRID_IMP_I6500:
+		c->cputype = CPU_I6500;
+		__cpu_name[cpu] = "MIPS I6500";
+		break;
+	case PRID_IMP_M5150:
+		c->cputype = CPU_M5150;
+		__cpu_name[cpu] = "MIPS M5150";
+		break;
+	case PRID_IMP_M6250:
+		c->cputype = CPU_M6250;
+		__cpu_name[cpu] = "MIPS M6250";
+		break;
+	}
+
+	decode_configs(c);
+
+	spram_config();
+
+	mm_config(c);
+
+	switch (__get_cpu_type(c->cputype)) {
+	case CPU_M5150:
+	case CPU_P5600:
+		set_isa(c, MIPS_CPU_ISA_M32R5);
+		break;
+	case CPU_I6500:
+		c->options |= MIPS_CPU_SHARED_FTLB_ENTRIES;
+		fallthrough;
+	case CPU_I6400:
+		c->options |= MIPS_CPU_SHARED_FTLB_RAM;
+		fallthrough;
+	default:
+		break;
+	}
+
+	/* Recent MIPS cores use the implementation-dependent ExcCode 16 for
+	 * cache/FTLB parity exceptions.
+	 */
+	switch (__get_cpu_type(c->cputype)) {
+	case CPU_PROAPTIV:
+	case CPU_P5600:
+	case CPU_P6600:
+	case CPU_I6400:
+	case CPU_I6500:
+		c->options |= MIPS_CPU_FTLBPAREX;
+		break;
+	}
+}
+
+static inline void cpu_probe_alchemy(struct cpuinfo_mips *c, unsigned int cpu)
+{
+	decode_configs(c);
+	switch (c->processor_id & PRID_IMP_MASK) {
+	case PRID_IMP_AU1_REV1:
+	case PRID_IMP_AU1_REV2:
+		c->cputype = CPU_ALCHEMY;
+		switch ((c->processor_id >> 24) & 0xff) {
+		case 0:
+			__cpu_name[cpu] = "Au1000";
+			break;
+		case 1:
+			__cpu_name[cpu] = "Au1500";
+			break;
+		case 2:
+			__cpu_name[cpu] = "Au1100";
+			break;
+		case 3:
+			__cpu_name[cpu] = "Au1550";
+			break;
+		case 4:
+			__cpu_name[cpu] = "Au1200";
+			if ((c->processor_id & PRID_REV_MASK) == 2)
+				__cpu_name[cpu] = "Au1250";
+			break;
+		case 5:
+			__cpu_name[cpu] = "Au1210";
+			break;
+		default:
+			__cpu_name[cpu] = "Au1xxx";
+			break;
+		}
+		break;
+	case PRID_IMP_NETLOGIC_AU13XX:
+		c->cputype = CPU_ALCHEMY;
+		__cpu_name[cpu] = "Au1300";
+		break;
+	}
+}
+
+static inline void cpu_probe_sibyte(struct cpuinfo_mips *c, unsigned int cpu)
+{
+	decode_configs(c);
+
+	c->writecombine = _CACHE_UNCACHED_ACCELERATED;
+	switch (c->processor_id & PRID_IMP_MASK) {
+	case PRID_IMP_SB1:
+		c->cputype = CPU_SB1;
+		__cpu_name[cpu] = "SiByte SB1";
+		/* FPU in pass1 is known to have issues. */
+		if ((c->processor_id & PRID_REV_MASK) < 0x02)
+			c->options &= ~(MIPS_CPU_FPU | MIPS_CPU_32FPR);
+		break;
+	case PRID_IMP_SB1A:
+		c->cputype = CPU_SB1A;
+		__cpu_name[cpu] = "SiByte SB1A";
+		break;
+	}
+}
+
+static inline void cpu_probe_sandcraft(struct cpuinfo_mips *c, unsigned int cpu)
+{
+	decode_configs(c);
+	switch (c->processor_id & PRID_IMP_MASK) {
+	case PRID_IMP_SR71000:
+		c->cputype = CPU_SR71000;
+		__cpu_name[cpu] = "Sandcraft SR71000";
+		c->scache.ways = 8;
+		c->tlbsize = 64;
+		break;
+	}
+}
+
+static inline void cpu_probe_nxp(struct cpuinfo_mips *c, unsigned int cpu)
+{
+	decode_configs(c);
+	switch (c->processor_id & PRID_IMP_MASK) {
+	case PRID_IMP_PR4450:
+		c->cputype = CPU_PR4450;
+		__cpu_name[cpu] = "Philips PR4450";
+		set_isa(c, MIPS_CPU_ISA_M32R1);
+		break;
+	}
+}
+
+static inline void cpu_probe_broadcom(struct cpuinfo_mips *c, unsigned int cpu)
+{
+	decode_configs(c);
+	switch (c->processor_id & PRID_IMP_MASK) {
+	case PRID_IMP_BMIPS32_REV4:
+	case PRID_IMP_BMIPS32_REV8:
+		c->cputype = CPU_BMIPS32;
+		__cpu_name[cpu] = "Broadcom BMIPS32";
+		set_elf_platform(cpu, "bmips32");
+		break;
+	case PRID_IMP_BMIPS3300:
+	case PRID_IMP_BMIPS3300_ALT:
+	case PRID_IMP_BMIPS3300_BUG:
+		c->cputype = CPU_BMIPS3300;
+		__cpu_name[cpu] = "Broadcom BMIPS3300";
+		set_elf_platform(cpu, "bmips3300");
+		reserve_exception_space(0x400, VECTORSPACING * 64);
+		break;
+	case PRID_IMP_BMIPS43XX: {
+		int rev = c->processor_id & PRID_REV_MASK;
+
+		if (rev >= PRID_REV_BMIPS4380_LO &&
+				rev <= PRID_REV_BMIPS4380_HI) {
+			c->cputype = CPU_BMIPS4380;
+			__cpu_name[cpu] = "Broadcom BMIPS4380";
+			set_elf_platform(cpu, "bmips4380");
+			c->options |= MIPS_CPU_RIXI;
+			reserve_exception_space(0x400, VECTORSPACING * 64);
+		} else {
+			c->cputype = CPU_BMIPS4350;
+			__cpu_name[cpu] = "Broadcom BMIPS4350";
+			set_elf_platform(cpu, "bmips4350");
+		}
+		break;
+	}
+	case PRID_IMP_BMIPS5000:
+	case PRID_IMP_BMIPS5200:
+		c->cputype = CPU_BMIPS5000;
+		if ((c->processor_id & PRID_IMP_MASK) == PRID_IMP_BMIPS5200)
+			__cpu_name[cpu] = "Broadcom BMIPS5200";
+		else
+			__cpu_name[cpu] = "Broadcom BMIPS5000";
+		set_elf_platform(cpu, "bmips5000");
+		c->options |= MIPS_CPU_ULRI | MIPS_CPU_RIXI;
+		reserve_exception_space(0x1000, VECTORSPACING * 64);
+		break;
+	}
+}
+
+static inline void cpu_probe_cavium(struct cpuinfo_mips *c, unsigned int cpu)
+{
+	decode_configs(c);
+	switch (c->processor_id & PRID_IMP_MASK) {
+	case PRID_IMP_CAVIUM_CN38XX:
+	case PRID_IMP_CAVIUM_CN31XX:
+	case PRID_IMP_CAVIUM_CN30XX:
+		c->cputype = CPU_CAVIUM_OCTEON;
+		__cpu_name[cpu] = "Cavium Octeon";
+		goto platform;
+	case PRID_IMP_CAVIUM_CN58XX:
+	case PRID_IMP_CAVIUM_CN56XX:
+	case PRID_IMP_CAVIUM_CN50XX:
+	case PRID_IMP_CAVIUM_CN52XX:
+		c->cputype = CPU_CAVIUM_OCTEON_PLUS;
+		__cpu_name[cpu] = "Cavium Octeon+";
+platform:
+		set_elf_platform(cpu, "octeon");
+		break;
+	case PRID_IMP_CAVIUM_CN61XX:
+	case PRID_IMP_CAVIUM_CN63XX:
+	case PRID_IMP_CAVIUM_CN66XX:
+	case PRID_IMP_CAVIUM_CN68XX:
+	case PRID_IMP_CAVIUM_CNF71XX:
+		c->cputype = CPU_CAVIUM_OCTEON2;
+		__cpu_name[cpu] = "Cavium Octeon II";
+		set_elf_platform(cpu, "octeon2");
+		break;
+	case PRID_IMP_CAVIUM_CN70XX:
+	case PRID_IMP_CAVIUM_CN73XX:
+	case PRID_IMP_CAVIUM_CNF75XX:
+	case PRID_IMP_CAVIUM_CN78XX:
+		c->cputype = CPU_CAVIUM_OCTEON3;
+		__cpu_name[cpu] = "Cavium Octeon III";
+		set_elf_platform(cpu, "octeon3");
+		break;
+	default:
+		printk(KERN_INFO "Unknown Octeon chip!\n");
+		c->cputype = CPU_UNKNOWN;
+		break;
+	}
+}
+
+#ifdef CONFIG_CPU_LOONGSON64
+#include <loongson_regs.h>
+
+static inline void decode_cpucfg(struct cpuinfo_mips *c)
+{
+	u32 cfg1 = read_cpucfg(LOONGSON_CFG1);
+	u32 cfg2 = read_cpucfg(LOONGSON_CFG2);
+	u32 cfg3 = read_cpucfg(LOONGSON_CFG3);
+
+	if (cfg1 & LOONGSON_CFG1_MMI)
+		c->ases |= MIPS_ASE_LOONGSON_MMI;
+
+	if (cfg2 & LOONGSON_CFG2_LEXT1)
+		c->ases |= MIPS_ASE_LOONGSON_EXT;
+
+	if (cfg2 & LOONGSON_CFG2_LEXT2)
+		c->ases |= MIPS_ASE_LOONGSON_EXT2;
+
+	if (cfg2 & LOONGSON_CFG2_LSPW) {
+		c->options |= MIPS_CPU_LDPTE;
+		c->guest.options |= MIPS_CPU_LDPTE;
+	}
+
+	if (cfg3 & LOONGSON_CFG3_LCAMP)
+		c->ases |= MIPS_ASE_LOONGSON_CAM;
+}
+
+static inline void cpu_probe_loongson(struct cpuinfo_mips *c, unsigned int cpu)
+{
+	c->cputype = CPU_LOONGSON64;
+
+	/* All Loongson processors covered here define ExcCode 16 as GSExc. */
+	decode_configs(c);
+	c->options |= MIPS_CPU_GSEXCEX;
+
+	switch (c->processor_id & PRID_IMP_MASK) {
+	case PRID_IMP_LOONGSON_64R: /* Loongson-64 Reduced */
+		switch (c->processor_id & PRID_REV_MASK) {
+		case PRID_REV_LOONGSON2K_R1_0:
+		case PRID_REV_LOONGSON2K_R1_1:
+		case PRID_REV_LOONGSON2K_R1_2:
+		case PRID_REV_LOONGSON2K_R1_3:
+			__cpu_name[cpu] = "Loongson-2K";
+			set_elf_platform(cpu, "gs264e");
+			set_isa(c, MIPS_CPU_ISA_M64R2);
+			break;
+		}
+		c->ases |= (MIPS_ASE_LOONGSON_MMI | MIPS_ASE_LOONGSON_EXT |
+				MIPS_ASE_LOONGSON_EXT2);
+		break;
+	case PRID_IMP_LOONGSON_64C:  /* Loongson-3 Classic */
+		switch (c->processor_id & PRID_REV_MASK) {
+		case PRID_REV_LOONGSON3A_R2_0:
+		case PRID_REV_LOONGSON3A_R2_1:
+			__cpu_name[cpu] = "ICT Loongson-3";
+			set_elf_platform(cpu, "loongson3a");
+			set_isa(c, MIPS_CPU_ISA_M64R2);
+			break;
+		case PRID_REV_LOONGSON3A_R3_0:
+		case PRID_REV_LOONGSON3A_R3_1:
+			__cpu_name[cpu] = "ICT Loongson-3";
+			set_elf_platform(cpu, "loongson3a");
+			set_isa(c, MIPS_CPU_ISA_M64R2);
+			break;
+		}
+		/*
+		 * Loongson-3 Classic did not implement MIPS standard TLBINV
+		 * but implemented TLBINVF and EHINV. As currently we're only
+		 * using these two features, enable MIPS_CPU_TLBINV as well.
+		 *
+		 * Also some early Loongson-3A2000 had wrong TLB type in Config
+		 * register, we correct it here.
+		 */
+		c->options |= MIPS_CPU_FTLB | MIPS_CPU_TLBINV | MIPS_CPU_LDPTE;
+		c->ases |= (MIPS_ASE_LOONGSON_MMI | MIPS_ASE_LOONGSON_CAM |
+			MIPS_ASE_LOONGSON_EXT | MIPS_ASE_LOONGSON_EXT2);
+		c->ases &= ~MIPS_ASE_VZ; /* VZ of Loongson-3A2000/3000 is incomplete */
+		break;
+	case PRID_IMP_LOONGSON_64G:
+		__cpu_name[cpu] = "ICT Loongson-3";
+		set_elf_platform(cpu, "loongson3a");
+		set_isa(c, MIPS_CPU_ISA_M64R2);
+		decode_cpucfg(c);
+		break;
+	default:
+		panic("Unknown Loongson Processor ID!");
+		break;
+	}
+}
+#else
+static inline void cpu_probe_loongson(struct cpuinfo_mips *c, unsigned int cpu) { }
+#endif
+
+static inline void cpu_probe_ingenic(struct cpuinfo_mips *c, unsigned int cpu)
+{
+	decode_configs(c);
+
+	/*
+	 * XBurst misses a config2 register, so config3 decode was skipped in
+	 * decode_configs().
+	 */
+	decode_config3(c);
+
+	/* XBurst does not implement the CP0 counter. */
+	c->options &= ~MIPS_CPU_COUNTER;
+	BUG_ON(__builtin_constant_p(cpu_has_counter) && cpu_has_counter);
+
+	/* XBurst has virtually tagged icache */
+	c->icache.flags |= MIPS_CACHE_VTAG;
+
+	switch (c->processor_id & PRID_IMP_MASK) {
+
+	/* XBurst®1 with MXU1.0/MXU1.1 SIMD ISA */
+	case PRID_IMP_XBURST_REV1:
+
+		/*
+		 * The XBurst core by default attempts to avoid branch target
+		 * buffer lookups by detecting & special casing loops. This
+		 * feature will cause BogoMIPS and lpj calculate in error.
+		 * Set cp0 config7 bit 4 to disable this feature.
+		 */
+		set_c0_config7(MIPS_CONF7_BTB_LOOP_EN);
+
+		switch (c->processor_id & PRID_COMP_MASK) {
+
+		/*
+		 * The config0 register in the XBurst CPUs with a processor ID of
+		 * PRID_COMP_INGENIC_D0 report themselves as MIPS32r2 compatible,
+		 * but they don't actually support this ISA.
+		 */
+		case PRID_COMP_INGENIC_D0:
+			c->isa_level &= ~MIPS_CPU_ISA_M32R2;
+
+			/* FPU is not properly detected on JZ4760(B). */
+			if (c->processor_id == 0x2ed0024f)
+				c->options |= MIPS_CPU_FPU;
+
+			fallthrough;
+
+		/*
+		 * The config0 register in the XBurst CPUs with a processor ID of
+		 * PRID_COMP_INGENIC_D0 or PRID_COMP_INGENIC_D1 has an abandoned
+		 * huge page tlb mode, this mode is not compatible with the MIPS
+		 * standard, it will cause tlbmiss and into an infinite loop
+		 * (line 21 in the tlb-funcs.S) when starting the init process.
+		 * After chip reset, the default is HPTLB mode, Write 0xa9000000
+		 * to cp0 register 5 sel 4 to switch back to VTLB mode to prevent
+		 * getting stuck.
+		 */
+		case PRID_COMP_INGENIC_D1:
+			write_c0_page_ctrl(XBURST_PAGECTRL_HPTLB_DIS);
+			break;
+
+		default:
+			break;
+		}
+		fallthrough;
+
+	/* XBurst®1 with MXU2.0 SIMD ISA */
+	case PRID_IMP_XBURST_REV2:
+		/* Ingenic uses the WA bit to achieve write-combine memory writes */
+		c->writecombine = _CACHE_CACHABLE_WA;
+		c->cputype = CPU_XBURST;
+		__cpu_name[cpu] = "Ingenic XBurst";
+		break;
+
+	/* XBurst®2 with MXU2.1 SIMD ISA */
+	case PRID_IMP_XBURST2:
+		c->cputype = CPU_XBURST;
+		__cpu_name[cpu] = "Ingenic XBurst II";
+		break;
+
+	default:
+		panic("Unknown Ingenic Processor ID!");
+		break;
+	}
+}
+
+#ifdef CONFIG_64BIT
+/* For use by uaccess.h */
+u64 __ua_limit;
+EXPORT_SYMBOL(__ua_limit);
+#endif
+
+const char *__cpu_name[NR_CPUS];
+const char *__elf_platform;
+const char *__elf_base_platform;
+
+void cpu_probe(void)
+{
+	struct cpuinfo_mips *c = &current_cpu_data;
+	unsigned int cpu = smp_processor_id();
+
+	/*
+	 * Set a default elf platform, cpu probe may later
+	 * overwrite it with a more precise value
+	 */
+	set_elf_platform(cpu, "mips");
+
+	c->processor_id = PRID_IMP_UNKNOWN;
+	c->fpu_id	= FPIR_IMP_NONE;
+	c->cputype	= CPU_UNKNOWN;
+	c->writecombine = _CACHE_UNCACHED;
+
+	c->fpu_csr31	= FPU_CSR_RN;
+	c->fpu_msk31	= FPU_CSR_RSVD | FPU_CSR_ABS2008 | FPU_CSR_NAN2008;
+
+	c->processor_id = read_c0_prid();
+	switch (c->processor_id & PRID_COMP_MASK) {
+	case PRID_COMP_LEGACY:
+		cpu_probe_legacy(c, cpu);
+		break;
+	case PRID_COMP_MIPS:
+		cpu_probe_mips(c, cpu);
+		break;
+	case PRID_COMP_ALCHEMY:
+	case PRID_COMP_NETLOGIC:
+		cpu_probe_alchemy(c, cpu);
+		break;
+	case PRID_COMP_SIBYTE:
+		cpu_probe_sibyte(c, cpu);
+		break;
+	case PRID_COMP_BROADCOM:
+		cpu_probe_broadcom(c, cpu);
+		break;
+	case PRID_COMP_SANDCRAFT:
+		cpu_probe_sandcraft(c, cpu);
+		break;
+	case PRID_COMP_NXP:
+		cpu_probe_nxp(c, cpu);
+		break;
+	case PRID_COMP_CAVIUM:
+		cpu_probe_cavium(c, cpu);
+		break;
+	case PRID_COMP_LOONGSON:
+		cpu_probe_loongson(c, cpu);
+		break;
+	case PRID_COMP_INGENIC_13:
+	case PRID_COMP_INGENIC_D0:
+	case PRID_COMP_INGENIC_D1:
+	case PRID_COMP_INGENIC_E1:
+		cpu_probe_ingenic(c, cpu);
+		break;
+	}
+
+	BUG_ON(!__cpu_name[cpu]);
+	BUG_ON(c->cputype == CPU_UNKNOWN);
+
+	/*
+	 * Platform code can force the cpu type to optimize code
+	 * generation. In that case be sure the cpu type is correctly
+	 * manually setup otherwise it could trigger some nasty bugs.
+	 */
+	BUG_ON(current_cpu_type() != c->cputype);
+
+	if (cpu_has_rixi) {
+		/* Enable the RIXI exceptions */
+		set_c0_pagegrain(PG_IEC);
+		back_to_back_c0_hazard();
+		/* Verify the IEC bit is set */
+		if (read_c0_pagegrain() & PG_IEC)
+			c->options |= MIPS_CPU_RIXIEX;
+	}
+
+	if (mips_fpu_disabled)
+		c->options &= ~MIPS_CPU_FPU;
+
+	if (mips_dsp_disabled)
+		c->ases &= ~(MIPS_ASE_DSP | MIPS_ASE_DSP2P);
+
+	if (mips_htw_disabled) {
+		c->options &= ~MIPS_CPU_HTW;
+		write_c0_pwctl(read_c0_pwctl() &
+			       ~(1 << MIPS_PWCTL_PWEN_SHIFT));
+	}
+
+	if (c->options & MIPS_CPU_FPU)
+		cpu_set_fpu_opts(c);
+	else
+		cpu_set_nofpu_opts(c);
+
+	if (cpu_has_mips_r2_r6) {
+		c->srsets = ((read_c0_srsctl() >> 26) & 0x0f) + 1;
+		/* R2 has Performance Counter Interrupt indicator */
+		c->options |= MIPS_CPU_PCI;
+	}
+	else
+		c->srsets = 1;
+
+	if (cpu_has_mips_r6)
+		elf_hwcap |= HWCAP_MIPS_R6;
+
+	if (cpu_has_msa) {
+		c->msa_id = cpu_get_msa_id();
+		WARN(c->msa_id & MSA_IR_WRPF,
+		     "Vector register partitioning unimplemented!");
+		elf_hwcap |= HWCAP_MIPS_MSA;
+	}
+
+	if (cpu_has_mips16)
+		elf_hwcap |= HWCAP_MIPS_MIPS16;
+
+	if (cpu_has_mdmx)
+		elf_hwcap |= HWCAP_MIPS_MDMX;
+
+	if (cpu_has_mips3d)
+		elf_hwcap |= HWCAP_MIPS_MIPS3D;
+
+	if (cpu_has_smartmips)
+		elf_hwcap |= HWCAP_MIPS_SMARTMIPS;
+
+	if (cpu_has_dsp)
+		elf_hwcap |= HWCAP_MIPS_DSP;
+
+	if (cpu_has_dsp2)
+		elf_hwcap |= HWCAP_MIPS_DSP2;
+
+	if (cpu_has_dsp3)
+		elf_hwcap |= HWCAP_MIPS_DSP3;
+
+	if (cpu_has_mips16e2)
+		elf_hwcap |= HWCAP_MIPS_MIPS16E2;
+
+	if (cpu_has_loongson_mmi)
+		elf_hwcap |= HWCAP_LOONGSON_MMI;
+
+	if (cpu_has_loongson_ext)
+		elf_hwcap |= HWCAP_LOONGSON_EXT;
+
+	if (cpu_has_loongson_ext2)
+		elf_hwcap |= HWCAP_LOONGSON_EXT2;
+
+	if (cpu_has_vz)
+		cpu_probe_vz(c);
+
+	cpu_probe_vmbits(c);
+
+	/* Synthesize CPUCFG data if running on Loongson processors;
+	 * no-op otherwise.
+	 *
+	 * This looks at previously probed features, so keep this at bottom.
+	 */
+	loongson3_cpucfg_synthesize_data(c);
+
+#ifdef CONFIG_64BIT
+	if (cpu == 0)
+		__ua_limit = ~((1ull << cpu_vmbits) - 1);
+#endif
+
+	reserve_exception_space(0, 0x1000);
+}
+
+void cpu_report(void)
+{
+	struct cpuinfo_mips *c = &current_cpu_data;
+
+	pr_info("CPU%d revision is: %08x (%s)\n",
+		smp_processor_id(), c->processor_id, cpu_name_string());
+	if (c->options & MIPS_CPU_FPU)
+		printk(KERN_INFO "FPU revision is: %08x\n", c->fpu_id);
+	if (cpu_has_msa)
+		pr_info("MSA revision is: %08x\n", c->msa_id);
+}
+
+void cpu_set_cluster(struct cpuinfo_mips *cpuinfo, unsigned int cluster)
+{
+	/* Ensure the core number fits in the field */
+	WARN_ON(cluster > (MIPS_GLOBALNUMBER_CLUSTER >>
+			   MIPS_GLOBALNUMBER_CLUSTER_SHF));
+
+	cpuinfo->globalnumber &= ~MIPS_GLOBALNUMBER_CLUSTER;
+	cpuinfo->globalnumber |= cluster << MIPS_GLOBALNUMBER_CLUSTER_SHF;
+}
+
+void cpu_set_core(struct cpuinfo_mips *cpuinfo, unsigned int core)
+{
+	/* Ensure the core number fits in the field */
+	WARN_ON(core > (MIPS_GLOBALNUMBER_CORE >> MIPS_GLOBALNUMBER_CORE_SHF));
+
+	cpuinfo->globalnumber &= ~MIPS_GLOBALNUMBER_CORE;
+	cpuinfo->globalnumber |= core << MIPS_GLOBALNUMBER_CORE_SHF;
+}
+
+void cpu_set_vpe_id(struct cpuinfo_mips *cpuinfo, unsigned int vpe)
+{
+	/* Ensure the VP(E) ID fits in the field */
+	WARN_ON(vpe > (MIPS_GLOBALNUMBER_VP >> MIPS_GLOBALNUMBER_VP_SHF));
+
+	/* Ensure we're not using VP(E)s without support */
+	WARN_ON(vpe && !IS_ENABLED(CONFIG_MIPS_MT_SMP) &&
+		!IS_ENABLED(CONFIG_CPU_MIPSR6));
+
+	cpuinfo->globalnumber &= ~MIPS_GLOBALNUMBER_VP;
+	cpuinfo->globalnumber |= vpe << MIPS_GLOBALNUMBER_VP_SHF;
+}
diff --git a/arch/mips/kernel/cpu-r3k-probe.c b/arch/mips/kernel/cpu-r3k-probe.c
new file mode 100644
index 000000000..be93469c0
--- /dev/null
+++ b/arch/mips/kernel/cpu-r3k-probe.c
@@ -0,0 +1,152 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Processor capabilities determination functions.
+ *
+ * Copyright (C) xxxx  the Anonymous
+ * Copyright (C) 1994 - 2006 Ralf Baechle
+ * Copyright (C) 2003, 2004  Maciej W. Rozycki
+ * Copyright (C) 2001, 2004, 2011, 2012	 MIPS Technologies, Inc.
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/ptrace.h>
+#include <linux/smp.h>
+#include <linux/stddef.h>
+#include <linux/export.h>
+
+#include <asm/bugs.h>
+#include <asm/cpu.h>
+#include <asm/cpu-features.h>
+#include <asm/cpu-type.h>
+#include <asm/fpu.h>
+#include <asm/mipsregs.h>
+#include <asm/elf.h>
+#include <asm/traps.h>
+
+#include "fpu-probe.h"
+
+/* Hardware capabilities */
+unsigned int elf_hwcap __read_mostly;
+EXPORT_SYMBOL_GPL(elf_hwcap);
+
+void __init check_bugs32(void)
+{
+
+}
+
+/*
+ * Probe whether cpu has config register by trying to play with
+ * alternate cache bit and see whether it matters.
+ * It's used by cpu_probe to distinguish between R3000A and R3081.
+ */
+static inline int cpu_has_confreg(void)
+{
+#ifdef CONFIG_CPU_R3000
+	extern unsigned long r3k_cache_size(unsigned long);
+	unsigned long size1, size2;
+	unsigned long cfg = read_c0_conf();
+
+	size1 = r3k_cache_size(ST0_ISC);
+	write_c0_conf(cfg ^ R30XX_CONF_AC);
+	size2 = r3k_cache_size(ST0_ISC);
+	write_c0_conf(cfg);
+	return size1 != size2;
+#else
+	return 0;
+#endif
+}
+
+static inline void set_elf_platform(int cpu, const char *plat)
+{
+	if (cpu == 0)
+		__elf_platform = plat;
+}
+
+const char *__cpu_name[NR_CPUS];
+const char *__elf_platform;
+const char *__elf_base_platform;
+
+void cpu_probe(void)
+{
+	struct cpuinfo_mips *c = &current_cpu_data;
+	unsigned int cpu = smp_processor_id();
+
+	/*
+	 * Set a default elf platform, cpu probe may later
+	 * overwrite it with a more precise value
+	 */
+	set_elf_platform(cpu, "mips");
+
+	c->processor_id = PRID_IMP_UNKNOWN;
+	c->fpu_id	= FPIR_IMP_NONE;
+	c->cputype	= CPU_UNKNOWN;
+	c->writecombine = _CACHE_UNCACHED;
+
+	c->fpu_csr31	= FPU_CSR_RN;
+	c->fpu_msk31	= FPU_CSR_RSVD | FPU_CSR_ABS2008 | FPU_CSR_NAN2008 |
+			  FPU_CSR_CONDX | FPU_CSR_FS;
+
+	c->srsets = 1;
+
+	c->processor_id = read_c0_prid();
+	switch (c->processor_id & (PRID_COMP_MASK | PRID_IMP_MASK)) {
+	case PRID_COMP_LEGACY | PRID_IMP_R2000:
+		c->cputype = CPU_R2000;
+		__cpu_name[cpu] = "R2000";
+		c->options = MIPS_CPU_TLB | MIPS_CPU_3K_CACHE |
+			     MIPS_CPU_NOFPUEX;
+		if (__cpu_has_fpu())
+			c->options |= MIPS_CPU_FPU;
+		c->tlbsize = 64;
+		break;
+	case PRID_COMP_LEGACY | PRID_IMP_R3000:
+		if ((c->processor_id & PRID_REV_MASK) == PRID_REV_R3000A) {
+			if (cpu_has_confreg()) {
+				c->cputype = CPU_R3081E;
+				__cpu_name[cpu] = "R3081";
+			} else {
+				c->cputype = CPU_R3000A;
+				__cpu_name[cpu] = "R3000A";
+			}
+		} else {
+			c->cputype = CPU_R3000;
+			__cpu_name[cpu] = "R3000";
+		}
+		c->options = MIPS_CPU_TLB | MIPS_CPU_3K_CACHE |
+			     MIPS_CPU_NOFPUEX;
+		if (__cpu_has_fpu())
+			c->options |= MIPS_CPU_FPU;
+		c->tlbsize = 64;
+		break;
+	}
+
+	BUG_ON(!__cpu_name[cpu]);
+	BUG_ON(c->cputype == CPU_UNKNOWN);
+
+	/*
+	 * Platform code can force the cpu type to optimize code
+	 * generation. In that case be sure the cpu type is correctly
+	 * manually setup otherwise it could trigger some nasty bugs.
+	 */
+	BUG_ON(current_cpu_type() != c->cputype);
+
+	if (mips_fpu_disabled)
+		c->options &= ~MIPS_CPU_FPU;
+
+	if (c->options & MIPS_CPU_FPU)
+		cpu_set_fpu_opts(c);
+	else
+		cpu_set_nofpu_opts(c);
+
+	reserve_exception_space(0, 0x400);
+}
+
+void cpu_report(void)
+{
+	struct cpuinfo_mips *c = &current_cpu_data;
+
+	pr_info("CPU%d revision is: %08x (%s)\n",
+		smp_processor_id(), c->processor_id, cpu_name_string());
+	if (c->options & MIPS_CPU_FPU)
+		pr_info("FPU revision is: %08x\n", c->fpu_id);
+}
diff --git a/arch/mips/kernel/crash.c b/arch/mips/kernel/crash.c
new file mode 100644
index 000000000..81845ba04
--- /dev/null
+++ b/arch/mips/kernel/crash.c
@@ -0,0 +1,103 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/kernel.h>
+#include <linux/smp.h>
+#include <linux/reboot.h>
+#include <linux/kexec.h>
+#include <linux/memblock.h>
+#include <linux/crash_dump.h>
+#include <linux/delay.h>
+#include <linux/irq.h>
+#include <linux/types.h>
+#include <linux/sched.h>
+#include <linux/sched/task_stack.h>
+
+/* This keeps a track of which one is crashing cpu. */
+static int crashing_cpu = -1;
+static cpumask_t cpus_in_crash = CPU_MASK_NONE;
+
+#ifdef CONFIG_SMP
+static void crash_shutdown_secondary(void *passed_regs)
+{
+	struct pt_regs *regs = passed_regs;
+	int cpu = smp_processor_id();
+
+	/*
+	 * If we are passed registers, use those.  Otherwise get the
+	 * regs from the last interrupt, which should be correct, as
+	 * we are in an interrupt.  But if the regs are not there,
+	 * pull them from the top of the stack.  They are probably
+	 * wrong, but we need something to keep from crashing again.
+	 */
+	if (!regs)
+		regs = get_irq_regs();
+	if (!regs)
+		regs = task_pt_regs(current);
+
+	if (!cpu_online(cpu))
+		return;
+
+	/* We won't be sent IPIs any more. */
+	set_cpu_online(cpu, false);
+
+	local_irq_disable();
+	if (!cpumask_test_cpu(cpu, &cpus_in_crash))
+		crash_save_cpu(regs, cpu);
+	cpumask_set_cpu(cpu, &cpus_in_crash);
+
+	while (!atomic_read(&kexec_ready_to_reboot))
+		cpu_relax();
+
+	kexec_reboot();
+
+	/* NOTREACHED */
+}
+
+static void crash_kexec_prepare_cpus(void)
+{
+	static int cpus_stopped;
+	unsigned int msecs;
+	unsigned int ncpus;
+
+	if (cpus_stopped)
+		return;
+
+	ncpus = num_online_cpus() - 1;/* Excluding the panic cpu */
+
+	smp_call_function(crash_shutdown_secondary, NULL, 0);
+	smp_wmb();
+
+	/*
+	 * The crash CPU sends an IPI and wait for other CPUs to
+	 * respond. Delay of at least 10 seconds.
+	 */
+	pr_emerg("Sending IPI to other cpus...\n");
+	msecs = 10000;
+	while ((cpumask_weight(&cpus_in_crash) < ncpus) && (--msecs > 0)) {
+		cpu_relax();
+		mdelay(1);
+	}
+
+	cpus_stopped = 1;
+}
+
+/* Override the weak function in kernel/panic.c */
+void crash_smp_send_stop(void)
+{
+	if (_crash_smp_send_stop)
+		_crash_smp_send_stop();
+
+	crash_kexec_prepare_cpus();
+}
+
+#else /* !defined(CONFIG_SMP)  */
+static void crash_kexec_prepare_cpus(void) {}
+#endif /* !defined(CONFIG_SMP)	*/
+
+void default_machine_crash_shutdown(struct pt_regs *regs)
+{
+	local_irq_disable();
+	crashing_cpu = smp_processor_id();
+	crash_save_cpu(regs, crashing_cpu);
+	crash_kexec_prepare_cpus();
+	cpumask_set_cpu(crashing_cpu, &cpus_in_crash);
+}
diff --git a/arch/mips/kernel/crash_dump.c b/arch/mips/kernel/crash_dump.c
new file mode 100644
index 000000000..6e50f4902
--- /dev/null
+++ b/arch/mips/kernel/crash_dump.c
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/highmem.h>
+#include <linux/crash_dump.h>
+#include <linux/uio.h>
+
+ssize_t copy_oldmem_page(struct iov_iter *iter, unsigned long pfn,
+			 size_t csize, unsigned long offset)
+{
+	void  *vaddr;
+
+	if (!csize)
+		return 0;
+
+	vaddr = kmap_local_pfn(pfn);
+	csize = copy_to_iter(vaddr + offset, csize, iter);
+	kunmap_local(vaddr);
+
+	return csize;
+}
diff --git a/arch/mips/kernel/csrc-bcm1480.c b/arch/mips/kernel/csrc-bcm1480.c
new file mode 100644
index 000000000..6c18a138f
--- /dev/null
+++ b/arch/mips/kernel/csrc-bcm1480.c
@@ -0,0 +1,48 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2000,2001,2004 Broadcom Corporation
+ */
+#include <linux/clocksource.h>
+#include <linux/sched_clock.h>
+
+#include <asm/addrspace.h>
+#include <asm/io.h>
+#include <asm/time.h>
+
+#include <asm/sibyte/bcm1480_regs.h>
+#include <asm/sibyte/sb1250_regs.h>
+#include <asm/sibyte/bcm1480_int.h>
+#include <asm/sibyte/bcm1480_scd.h>
+
+#include <asm/sibyte/sb1250.h>
+
+static u64 bcm1480_hpt_read(struct clocksource *cs)
+{
+	return (u64) __raw_readq(IOADDR(A_SCD_ZBBUS_CYCLE_COUNT));
+}
+
+struct clocksource bcm1480_clocksource = {
+	.name	= "zbbus-cycles",
+	.rating = 200,
+	.read	= bcm1480_hpt_read,
+	.mask	= CLOCKSOURCE_MASK(64),
+	.flags	= CLOCK_SOURCE_IS_CONTINUOUS,
+};
+
+static u64 notrace sb1480_read_sched_clock(void)
+{
+	return __raw_readq(IOADDR(A_SCD_ZBBUS_CYCLE_COUNT));
+}
+
+void __init sb1480_clocksource_init(void)
+{
+	struct clocksource *cs = &bcm1480_clocksource;
+	unsigned int plldiv;
+	unsigned long zbbus;
+
+	plldiv = G_BCM1480_SYS_PLL_DIV(__raw_readq(IOADDR(A_SCD_SYSTEM_CFG)));
+	zbbus = ((plldiv >> 1) * 50000000) + ((plldiv & 1) * 25000000);
+	clocksource_register_hz(cs, zbbus);
+
+	sched_clock_register(sb1480_read_sched_clock, 64, zbbus);
+}
diff --git a/arch/mips/kernel/csrc-ioasic.c b/arch/mips/kernel/csrc-ioasic.c
new file mode 100644
index 000000000..bad740ad3
--- /dev/null
+++ b/arch/mips/kernel/csrc-ioasic.c
@@ -0,0 +1,65 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *  DEC I/O ASIC's counter clocksource
+ *
+ *  Copyright (C) 2008	Yoichi Yuasa <yuasa@linux-mips.org>
+ */
+#include <linux/clocksource.h>
+#include <linux/sched_clock.h>
+#include <linux/init.h>
+
+#include <asm/ds1287.h>
+#include <asm/time.h>
+#include <asm/dec/ioasic.h>
+#include <asm/dec/ioasic_addrs.h>
+
+static u64 dec_ioasic_hpt_read(struct clocksource *cs)
+{
+	return ioasic_read(IO_REG_FCTR);
+}
+
+static struct clocksource clocksource_dec = {
+	.name		= "dec-ioasic",
+	.read		= dec_ioasic_hpt_read,
+	.mask		= CLOCKSOURCE_MASK(32),
+	.flags		= CLOCK_SOURCE_IS_CONTINUOUS,
+};
+
+static u64 notrace dec_ioasic_read_sched_clock(void)
+{
+	return ioasic_read(IO_REG_FCTR);
+}
+
+int __init dec_ioasic_clocksource_init(void)
+{
+	unsigned int freq;
+	u32 start, end;
+	int i = HZ / 8;
+
+	ds1287_timer_state();
+	while (!ds1287_timer_state())
+		;
+
+	start = dec_ioasic_hpt_read(&clocksource_dec);
+
+	while (i--)
+		while (!ds1287_timer_state())
+			;
+
+	end = dec_ioasic_hpt_read(&clocksource_dec);
+
+	freq = (end - start) * 8;
+
+	/* An early revision of the I/O ASIC didn't have the counter.  */
+	if (!freq)
+		return -ENXIO;
+
+	printk(KERN_INFO "I/O ASIC clock frequency %dHz\n", freq);
+
+	clocksource_dec.rating = 200 + freq / 10000000;
+	clocksource_register_hz(&clocksource_dec, freq);
+
+	sched_clock_register(dec_ioasic_read_sched_clock, 32, freq);
+
+	return 0;
+}
diff --git a/arch/mips/kernel/csrc-r4k.c b/arch/mips/kernel/csrc-r4k.c
new file mode 100644
index 000000000..edc4afc08
--- /dev/null
+++ b/arch/mips/kernel/csrc-r4k.c
@@ -0,0 +1,130 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2007 by Ralf Baechle
+ */
+#include <linux/clocksource.h>
+#include <linux/cpufreq.h>
+#include <linux/init.h>
+#include <linux/sched_clock.h>
+
+#include <asm/time.h>
+
+static u64 c0_hpt_read(struct clocksource *cs)
+{
+	return read_c0_count();
+}
+
+static struct clocksource clocksource_mips = {
+	.name		= "MIPS",
+	.read		= c0_hpt_read,
+	.mask		= CLOCKSOURCE_MASK(32),
+	.flags		= CLOCK_SOURCE_IS_CONTINUOUS,
+};
+
+static u64 __maybe_unused notrace r4k_read_sched_clock(void)
+{
+	return read_c0_count();
+}
+
+static inline unsigned int rdhwr_count(void)
+{
+	unsigned int count;
+
+	__asm__ __volatile__(
+	"	.set push\n"
+	"	.set mips32r2\n"
+	"	rdhwr	%0, $2\n"
+	"	.set pop\n"
+	: "=r" (count));
+
+	return count;
+}
+
+static bool rdhwr_count_usable(void)
+{
+	unsigned int prev, curr, i;
+
+	/*
+	 * Older QEMUs have a broken implementation of RDHWR for the CP0 count
+	 * which always returns a constant value. Try to identify this and don't
+	 * use it in the VDSO if it is broken. This workaround can be removed
+	 * once the fix has been in QEMU stable for a reasonable amount of time.
+	 */
+	for (i = 0, prev = rdhwr_count(); i < 100; i++) {
+		curr = rdhwr_count();
+
+		if (curr != prev)
+			return true;
+
+		prev = curr;
+	}
+
+	pr_warn("Not using R4K clocksource in VDSO due to broken RDHWR\n");
+	return false;
+}
+
+#ifdef CONFIG_CPU_FREQ
+
+static bool __read_mostly r4k_clock_unstable;
+
+static void r4k_clocksource_unstable(char *reason)
+{
+	if (r4k_clock_unstable)
+		return;
+
+	r4k_clock_unstable = true;
+
+	pr_info("R4K timer is unstable due to %s\n", reason);
+
+	clocksource_mark_unstable(&clocksource_mips);
+}
+
+static int r4k_cpufreq_callback(struct notifier_block *nb,
+				unsigned long val, void *data)
+{
+	if (val == CPUFREQ_POSTCHANGE)
+		r4k_clocksource_unstable("CPU frequency change");
+
+	return 0;
+}
+
+static struct notifier_block r4k_cpufreq_notifier = {
+	.notifier_call  = r4k_cpufreq_callback,
+};
+
+static int __init r4k_register_cpufreq_notifier(void)
+{
+	return cpufreq_register_notifier(&r4k_cpufreq_notifier,
+					 CPUFREQ_TRANSITION_NOTIFIER);
+
+}
+core_initcall(r4k_register_cpufreq_notifier);
+
+#endif /* !CONFIG_CPU_FREQ */
+
+int __init init_r4k_clocksource(void)
+{
+	if (!cpu_has_counter || !mips_hpt_frequency)
+		return -ENXIO;
+
+	/* Calculate a somewhat reasonable rating value */
+	clocksource_mips.rating = 200 + mips_hpt_frequency / 10000000;
+
+	/*
+	 * R2 onwards makes the count accessible to user mode so it can be used
+	 * by the VDSO (HWREna is configured by configure_hwrena()).
+	 */
+	if (cpu_has_mips_r2_r6 && rdhwr_count_usable())
+		clocksource_mips.vdso_clock_mode = VDSO_CLOCKMODE_R4K;
+
+	clocksource_register_hz(&clocksource_mips, mips_hpt_frequency);
+
+#ifndef CONFIG_CPU_FREQ
+	sched_clock_register(r4k_read_sched_clock, 32, mips_hpt_frequency);
+#endif
+
+	return 0;
+}
diff --git a/arch/mips/kernel/csrc-sb1250.c b/arch/mips/kernel/csrc-sb1250.c
new file mode 100644
index 000000000..fa2fa3e10
--- /dev/null
+++ b/arch/mips/kernel/csrc-sb1250.c
@@ -0,0 +1,71 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2000, 2001 Broadcom Corporation
+ */
+#include <linux/clocksource.h>
+#include <linux/sched_clock.h>
+
+#include <asm/addrspace.h>
+#include <asm/io.h>
+#include <asm/time.h>
+
+#include <asm/sibyte/sb1250.h>
+#include <asm/sibyte/sb1250_regs.h>
+#include <asm/sibyte/sb1250_int.h>
+#include <asm/sibyte/sb1250_scd.h>
+
+#define SB1250_HPT_NUM		3
+#define SB1250_HPT_VALUE	M_SCD_TIMER_CNT /* max value */
+
+/*
+ * The HPT is free running from SB1250_HPT_VALUE down to 0 then starts over
+ * again.
+ */
+static inline u64 sb1250_hpt_get_cycles(void)
+{
+	unsigned int count;
+	void __iomem *addr;
+
+	addr = IOADDR(A_SCD_TIMER_REGISTER(SB1250_HPT_NUM, R_SCD_TIMER_CNT));
+	count = G_SCD_TIMER_CNT(__raw_readq(addr));
+
+	return SB1250_HPT_VALUE - count;
+}
+
+static u64 sb1250_hpt_read(struct clocksource *cs)
+{
+	return sb1250_hpt_get_cycles();
+}
+
+struct clocksource bcm1250_clocksource = {
+	.name	= "bcm1250-counter-3",
+	.rating = 200,
+	.read	= sb1250_hpt_read,
+	.mask	= CLOCKSOURCE_MASK(23),
+	.flags	= CLOCK_SOURCE_IS_CONTINUOUS,
+};
+
+static u64 notrace sb1250_read_sched_clock(void)
+{
+	return sb1250_hpt_get_cycles();
+}
+
+void __init sb1250_clocksource_init(void)
+{
+	struct clocksource *cs = &bcm1250_clocksource;
+
+	/* Setup hpt using timer #3 but do not enable irq for it */
+	__raw_writeq(0,
+		     IOADDR(A_SCD_TIMER_REGISTER(SB1250_HPT_NUM,
+						 R_SCD_TIMER_CFG)));
+	__raw_writeq(SB1250_HPT_VALUE,
+		     IOADDR(A_SCD_TIMER_REGISTER(SB1250_HPT_NUM,
+						 R_SCD_TIMER_INIT)));
+	__raw_writeq(M_SCD_TIMER_ENABLE | M_SCD_TIMER_MODE_CONTINUOUS,
+		     IOADDR(A_SCD_TIMER_REGISTER(SB1250_HPT_NUM,
+						 R_SCD_TIMER_CFG)));
+
+	clocksource_register_hz(cs, V_SCD_TIMER_FREQ);
+
+	sched_clock_register(sb1250_read_sched_clock, 23, V_SCD_TIMER_FREQ);
+}
diff --git a/arch/mips/kernel/early_printk.c b/arch/mips/kernel/early_printk.c
new file mode 100644
index 000000000..4a1647ddf
--- /dev/null
+++ b/arch/mips/kernel/early_printk.c
@@ -0,0 +1,41 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2002, 2003, 06, 07 Ralf Baechle (ralf@linux-mips.org)
+ * Copyright (C) 2007 MIPS Technologies, Inc.
+ *   written by Ralf Baechle (ralf@linux-mips.org)
+ */
+#include <linux/kernel.h>
+#include <linux/console.h>
+#include <linux/printk.h>
+#include <linux/init.h>
+
+#include <asm/setup.h>
+
+static void early_console_write(struct console *con, const char *s, unsigned n)
+{
+	while (n-- && *s) {
+		if (*s == '\n')
+			prom_putchar('\r');
+		prom_putchar(*s);
+		s++;
+	}
+}
+
+static struct console early_console_prom = {
+	.name	= "early",
+	.write	= early_console_write,
+	.flags	= CON_PRINTBUFFER | CON_BOOT,
+	.index	= -1
+};
+
+void __init setup_early_printk(void)
+{
+	if (early_console)
+		return;
+	early_console = &early_console_prom;
+
+	register_console(&early_console_prom);
+}
diff --git a/arch/mips/kernel/early_printk_8250.c b/arch/mips/kernel/early_printk_8250.c
new file mode 100644
index 000000000..567c6ec0c
--- /dev/null
+++ b/arch/mips/kernel/early_printk_8250.c
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *  8250/16550-type serial ports prom_putchar()
+ *
+ *  Copyright (C) 2010  Yoichi Yuasa <yuasa@linux-mips.org>
+ */
+#include <linux/io.h>
+#include <linux/serial_core.h>
+#include <linux/serial_reg.h>
+#include <asm/setup.h>
+
+static void __iomem *serial8250_base;
+static unsigned int serial8250_reg_shift;
+static unsigned int serial8250_tx_timeout;
+
+void setup_8250_early_printk_port(unsigned long base, unsigned int reg_shift,
+				  unsigned int timeout)
+{
+	serial8250_base = (void __iomem *)base;
+	serial8250_reg_shift = reg_shift;
+	serial8250_tx_timeout = timeout;
+}
+
+static inline u8 serial_in(int offset)
+{
+	return readb(serial8250_base + (offset << serial8250_reg_shift));
+}
+
+static inline void serial_out(int offset, char value)
+{
+	writeb(value, serial8250_base + (offset << serial8250_reg_shift));
+}
+
+void prom_putchar(char c)
+{
+	unsigned int timeout;
+	int status, bits;
+
+	if (!serial8250_base)
+		return;
+
+	timeout = serial8250_tx_timeout;
+	bits = UART_LSR_TEMT | UART_LSR_THRE;
+
+	do {
+		status = serial_in(UART_LSR);
+
+		if (--timeout == 0)
+			break;
+	} while ((status & bits) != bits);
+
+	if (timeout)
+		serial_out(UART_TX, c);
+}
diff --git a/arch/mips/kernel/elf.c b/arch/mips/kernel/elf.c
new file mode 100644
index 000000000..7aa2c2360
--- /dev/null
+++ b/arch/mips/kernel/elf.c
@@ -0,0 +1,343 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2014 Imagination Technologies
+ * Author: Paul Burton <paul.burton@mips.com>
+ */
+
+#include <linux/binfmts.h>
+#include <linux/elf.h>
+#include <linux/export.h>
+#include <linux/sched.h>
+
+#include <asm/cpu-features.h>
+#include <asm/cpu-info.h>
+#include <asm/fpu.h>
+
+#ifdef CONFIG_MIPS_FP_SUPPORT
+
+/* Whether to accept legacy-NaN and 2008-NaN user binaries.  */
+bool mips_use_nan_legacy;
+bool mips_use_nan_2008;
+
+/* FPU modes */
+enum {
+	FP_FRE,
+	FP_FR0,
+	FP_FR1,
+};
+
+/**
+ * struct mode_req - ABI FPU mode requirements
+ * @single:	The program being loaded needs an FPU but it will only issue
+ *		single precision instructions meaning that it can execute in
+ *		either FR0 or FR1.
+ * @soft:	The soft(-float) requirement means that the program being
+ *		loaded needs has no FPU dependency at all (i.e. it has no
+ *		FPU instructions).
+ * @fr1:	The program being loaded depends on FPU being in FR=1 mode.
+ * @frdefault:	The program being loaded depends on the default FPU mode.
+ *		That is FR0 for O32 and FR1 for N32/N64.
+ * @fre:	The program being loaded depends on FPU with FRE=1. This mode is
+ *		a bridge which uses FR=1 whilst still being able to maintain
+ *		full compatibility with pre-existing code using the O32 FP32
+ *		ABI.
+ *
+ * More information about the FP ABIs can be found here:
+ *
+ * https://dmz-portal.mips.com/wiki/MIPS_O32_ABI_-_FR0_and_FR1_Interlinking#10.4.1._Basic_mode_set-up
+ *
+ */
+
+struct mode_req {
+	bool single;
+	bool soft;
+	bool fr1;
+	bool frdefault;
+	bool fre;
+};
+
+static const struct mode_req fpu_reqs[] = {
+	[MIPS_ABI_FP_ANY]    = { true,  true,  true,  true,  true  },
+	[MIPS_ABI_FP_DOUBLE] = { false, false, false, true,  true  },
+	[MIPS_ABI_FP_SINGLE] = { true,  false, false, false, false },
+	[MIPS_ABI_FP_SOFT]   = { false, true,  false, false, false },
+	[MIPS_ABI_FP_OLD_64] = { false, false, false, false, false },
+	[MIPS_ABI_FP_XX]     = { false, false, true,  true,  true  },
+	[MIPS_ABI_FP_64]     = { false, false, true,  false, false },
+	[MIPS_ABI_FP_64A]    = { false, false, true,  false, true  }
+};
+
+/*
+ * Mode requirements when .MIPS.abiflags is not present in the ELF.
+ * Not present means that everything is acceptable except FR1.
+ */
+static struct mode_req none_req = { true, true, false, true, true };
+
+int arch_elf_pt_proc(void *_ehdr, void *_phdr, struct file *elf,
+		     bool is_interp, struct arch_elf_state *state)
+{
+	union {
+		struct elf32_hdr e32;
+		struct elf64_hdr e64;
+	} *ehdr = _ehdr;
+	struct elf32_phdr *phdr32 = _phdr;
+	struct elf64_phdr *phdr64 = _phdr;
+	struct mips_elf_abiflags_v0 abiflags;
+	bool elf32;
+	u32 flags;
+	int ret;
+	loff_t pos;
+
+	elf32 = ehdr->e32.e_ident[EI_CLASS] == ELFCLASS32;
+	flags = elf32 ? ehdr->e32.e_flags : ehdr->e64.e_flags;
+
+	/* Let's see if this is an O32 ELF */
+	if (elf32) {
+		if (flags & EF_MIPS_FP64) {
+			/*
+			 * Set MIPS_ABI_FP_OLD_64 for EF_MIPS_FP64. We will override it
+			 * later if needed
+			 */
+			if (is_interp)
+				state->interp_fp_abi = MIPS_ABI_FP_OLD_64;
+			else
+				state->fp_abi = MIPS_ABI_FP_OLD_64;
+		}
+		if (phdr32->p_type != PT_MIPS_ABIFLAGS)
+			return 0;
+
+		if (phdr32->p_filesz < sizeof(abiflags))
+			return -EINVAL;
+		pos = phdr32->p_offset;
+	} else {
+		if (phdr64->p_type != PT_MIPS_ABIFLAGS)
+			return 0;
+		if (phdr64->p_filesz < sizeof(abiflags))
+			return -EINVAL;
+		pos = phdr64->p_offset;
+	}
+
+	ret = kernel_read(elf, &abiflags, sizeof(abiflags), &pos);
+	if (ret < 0)
+		return ret;
+	if (ret != sizeof(abiflags))
+		return -EIO;
+
+	/* Record the required FP ABIs for use by mips_check_elf */
+	if (is_interp)
+		state->interp_fp_abi = abiflags.fp_abi;
+	else
+		state->fp_abi = abiflags.fp_abi;
+
+	return 0;
+}
+
+int arch_check_elf(void *_ehdr, bool has_interpreter, void *_interp_ehdr,
+		   struct arch_elf_state *state)
+{
+	union {
+		struct elf32_hdr e32;
+		struct elf64_hdr e64;
+	} *ehdr = _ehdr;
+	union {
+		struct elf32_hdr e32;
+		struct elf64_hdr e64;
+	} *iehdr = _interp_ehdr;
+	struct mode_req prog_req, interp_req;
+	int fp_abi, interp_fp_abi, abi0, abi1, max_abi;
+	bool elf32;
+	u32 flags;
+
+	elf32 = ehdr->e32.e_ident[EI_CLASS] == ELFCLASS32;
+	flags = elf32 ? ehdr->e32.e_flags : ehdr->e64.e_flags;
+
+	/*
+	 * Determine the NaN personality, reject the binary if not allowed.
+	 * Also ensure that any interpreter matches the executable.
+	 */
+	if (flags & EF_MIPS_NAN2008) {
+		if (mips_use_nan_2008)
+			state->nan_2008 = 1;
+		else
+			return -ENOEXEC;
+	} else {
+		if (mips_use_nan_legacy)
+			state->nan_2008 = 0;
+		else
+			return -ENOEXEC;
+	}
+	if (has_interpreter) {
+		bool ielf32;
+		u32 iflags;
+
+		ielf32 = iehdr->e32.e_ident[EI_CLASS] == ELFCLASS32;
+		iflags = ielf32 ? iehdr->e32.e_flags : iehdr->e64.e_flags;
+
+		if ((flags ^ iflags) & EF_MIPS_NAN2008)
+			return -ELIBBAD;
+	}
+
+	if (!IS_ENABLED(CONFIG_MIPS_O32_FP64_SUPPORT))
+		return 0;
+
+	fp_abi = state->fp_abi;
+
+	if (has_interpreter) {
+		interp_fp_abi = state->interp_fp_abi;
+
+		abi0 = min(fp_abi, interp_fp_abi);
+		abi1 = max(fp_abi, interp_fp_abi);
+	} else {
+		abi0 = abi1 = fp_abi;
+	}
+
+	if (elf32 && !(flags & EF_MIPS_ABI2)) {
+		/* Default to a mode capable of running code expecting FR=0 */
+		state->overall_fp_mode = cpu_has_mips_r6 ? FP_FRE : FP_FR0;
+
+		/* Allow all ABIs we know about */
+		max_abi = MIPS_ABI_FP_64A;
+	} else {
+		/* MIPS64 code always uses FR=1, thus the default is easy */
+		state->overall_fp_mode = FP_FR1;
+
+		/* Disallow access to the various FPXX & FP64 ABIs */
+		max_abi = MIPS_ABI_FP_SOFT;
+	}
+
+	if ((abi0 > max_abi && abi0 != MIPS_ABI_FP_UNKNOWN) ||
+	    (abi1 > max_abi && abi1 != MIPS_ABI_FP_UNKNOWN))
+		return -ELIBBAD;
+
+	/* It's time to determine the FPU mode requirements */
+	prog_req = (abi0 == MIPS_ABI_FP_UNKNOWN) ? none_req : fpu_reqs[abi0];
+	interp_req = (abi1 == MIPS_ABI_FP_UNKNOWN) ? none_req : fpu_reqs[abi1];
+
+	/*
+	 * Check whether the program's and interp's ABIs have a matching FPU
+	 * mode requirement.
+	 */
+	prog_req.single = interp_req.single && prog_req.single;
+	prog_req.soft = interp_req.soft && prog_req.soft;
+	prog_req.fr1 = interp_req.fr1 && prog_req.fr1;
+	prog_req.frdefault = interp_req.frdefault && prog_req.frdefault;
+	prog_req.fre = interp_req.fre && prog_req.fre;
+
+	/*
+	 * Determine the desired FPU mode
+	 *
+	 * Decision making:
+	 *
+	 * - We want FR_FRE if FRE=1 and both FR=1 and FR=0 are false. This
+	 *   means that we have a combination of program and interpreter
+	 *   that inherently require the hybrid FP mode.
+	 * - If FR1 and FRDEFAULT is true, that means we hit the any-abi or
+	 *   fpxx case. This is because, in any-ABI (or no-ABI) we have no FPU
+	 *   instructions so we don't care about the mode. We will simply use
+	 *   the one preferred by the hardware. In fpxx case, that ABI can
+	 *   handle both FR=1 and FR=0, so, again, we simply choose the one
+	 *   preferred by the hardware. Next, if we only use single-precision
+	 *   FPU instructions, and the default ABI FPU mode is not good
+	 *   (ie single + any ABI combination), we set again the FPU mode to the
+	 *   one is preferred by the hardware. Next, if we know that the code
+	 *   will only use single-precision instructions, shown by single being
+	 *   true but frdefault being false, then we again set the FPU mode to
+	 *   the one that is preferred by the hardware.
+	 * - We want FP_FR1 if that's the only matching mode and the default one
+	 *   is not good.
+	 * - Return with -ELIBADD if we can't find a matching FPU mode.
+	 */
+	if (prog_req.fre && !prog_req.frdefault && !prog_req.fr1)
+		state->overall_fp_mode = FP_FRE;
+	else if ((prog_req.fr1 && prog_req.frdefault) ||
+		 (prog_req.single && !prog_req.frdefault))
+		/* Make sure 64-bit MIPS III/IV/64R1 will not pick FR1 */
+		state->overall_fp_mode = ((raw_current_cpu_data.fpu_id & MIPS_FPIR_F64) &&
+					  cpu_has_mips_r2_r6) ?
+					  FP_FR1 : FP_FR0;
+	else if (prog_req.fr1)
+		state->overall_fp_mode = FP_FR1;
+	else  if (!prog_req.fre && !prog_req.frdefault &&
+		  !prog_req.fr1 && !prog_req.single && !prog_req.soft)
+		return -ELIBBAD;
+
+	return 0;
+}
+
+static inline void set_thread_fp_mode(int hybrid, int regs32)
+{
+	if (hybrid)
+		set_thread_flag(TIF_HYBRID_FPREGS);
+	else
+		clear_thread_flag(TIF_HYBRID_FPREGS);
+	if (regs32)
+		set_thread_flag(TIF_32BIT_FPREGS);
+	else
+		clear_thread_flag(TIF_32BIT_FPREGS);
+}
+
+void mips_set_personality_fp(struct arch_elf_state *state)
+{
+	/*
+	 * This function is only ever called for O32 ELFs so we should
+	 * not be worried about N32/N64 binaries.
+	 */
+
+	if (!IS_ENABLED(CONFIG_MIPS_O32_FP64_SUPPORT))
+		return;
+
+	switch (state->overall_fp_mode) {
+	case FP_FRE:
+		set_thread_fp_mode(1, 0);
+		break;
+	case FP_FR0:
+		set_thread_fp_mode(0, 1);
+		break;
+	case FP_FR1:
+		set_thread_fp_mode(0, 0);
+		break;
+	default:
+		BUG();
+	}
+}
+
+/*
+ * Select the IEEE 754 NaN encoding and ABS.fmt/NEG.fmt execution mode
+ * in FCSR according to the ELF NaN personality.
+ */
+void mips_set_personality_nan(struct arch_elf_state *state)
+{
+	struct cpuinfo_mips *c = &boot_cpu_data;
+	struct task_struct *t = current;
+
+	/* Do this early so t->thread.fpu.fcr31 won't be clobbered in case
+	 * we are preempted before the lose_fpu(0) in start_thread.
+	 */
+	lose_fpu(0);
+
+	t->thread.fpu.fcr31 = c->fpu_csr31;
+	switch (state->nan_2008) {
+	case 0:
+		break;
+	case 1:
+		if (!(c->fpu_msk31 & FPU_CSR_NAN2008))
+			t->thread.fpu.fcr31 |= FPU_CSR_NAN2008;
+		if (!(c->fpu_msk31 & FPU_CSR_ABS2008))
+			t->thread.fpu.fcr31 |= FPU_CSR_ABS2008;
+		break;
+	default:
+		BUG();
+	}
+}
+
+#endif /* CONFIG_MIPS_FP_SUPPORT */
+
+int mips_elf_read_implies_exec(void *elf_ex, int exstack)
+{
+	/*
+	 * Set READ_IMPLIES_EXEC only on non-NX systems that
+	 * do not request a specific state via PT_GNU_STACK.
+	 */
+	return (!cpu_has_rixi && exstack == EXSTACK_DEFAULT);
+}
+EXPORT_SYMBOL(mips_elf_read_implies_exec);
diff --git a/arch/mips/kernel/entry.S b/arch/mips/kernel/entry.S
new file mode 100644
index 000000000..891393626
--- /dev/null
+++ b/arch/mips/kernel/entry.S
@@ -0,0 +1,185 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994 - 2000, 2001, 2003 Ralf Baechle
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ * Copyright (C) 2001 MIPS Technologies, Inc.
+ */
+
+#include <asm/asm.h>
+#include <asm/asmmacro.h>
+#include <asm/compiler.h>
+#include <asm/irqflags.h>
+#include <asm/regdef.h>
+#include <asm/mipsregs.h>
+#include <asm/stackframe.h>
+#include <asm/isadep.h>
+#include <asm/thread_info.h>
+
+#ifndef CONFIG_PREEMPTION
+#define resume_kernel	restore_all
+#else
+#define __ret_from_irq	ret_from_exception
+#endif
+
+	.text
+	.align	5
+#ifndef CONFIG_PREEMPTION
+FEXPORT(ret_from_exception)
+	local_irq_disable			# preempt stop
+	b	__ret_from_irq
+#endif
+FEXPORT(ret_from_irq)
+	LONG_S	s0, TI_REGS($28)
+FEXPORT(__ret_from_irq)
+/*
+ * We can be coming here from a syscall done in the kernel space,
+ * e.g. a failed kernel_execve().
+ */
+resume_userspace_check:
+	LONG_L	t0, PT_STATUS(sp)		# returning to kernel mode?
+	andi	t0, t0, KU_USER
+	beqz	t0, resume_kernel
+
+resume_userspace:
+	local_irq_disable		# make sure we dont miss an
+					# interrupt setting need_resched
+					# between sampling and return
+	LONG_L	a2, TI_FLAGS($28)	# current->work
+	andi	t0, a2, _TIF_WORK_MASK	# (ignoring syscall_trace)
+	bnez	t0, work_pending
+	j	restore_all
+
+#ifdef CONFIG_PREEMPTION
+resume_kernel:
+	local_irq_disable
+	lw	t0, TI_PRE_COUNT($28)
+	bnez	t0, restore_all
+	LONG_L	t0, TI_FLAGS($28)
+	andi	t1, t0, _TIF_NEED_RESCHED
+	beqz	t1, restore_all
+	LONG_L	t0, PT_STATUS(sp)		# Interrupts off?
+	andi	t0, 1
+	beqz	t0, restore_all
+	PTR_LA	ra, restore_all
+	j	preempt_schedule_irq
+#endif
+
+FEXPORT(ret_from_kernel_thread)
+	jal	schedule_tail		# a0 = struct task_struct *prev
+	move	a0, s1
+	jal	s0
+	j	syscall_exit
+
+FEXPORT(ret_from_fork)
+	jal	schedule_tail		# a0 = struct task_struct *prev
+
+FEXPORT(syscall_exit)
+#ifdef CONFIG_DEBUG_RSEQ
+	move	a0, sp
+	jal	rseq_syscall
+#endif
+	local_irq_disable		# make sure need_resched and
+					# signals dont change between
+					# sampling and return
+	LONG_L	a2, TI_FLAGS($28)	# current->work
+	li	t0, _TIF_ALLWORK_MASK
+	and	t0, a2, t0
+	bnez	t0, syscall_exit_work
+
+restore_all:				# restore full frame
+	.set	noat
+	RESTORE_TEMP
+	RESTORE_AT
+	RESTORE_STATIC
+restore_partial:		# restore partial frame
+#ifdef CONFIG_TRACE_IRQFLAGS
+	SAVE_STATIC
+	SAVE_AT
+	SAVE_TEMP
+	LONG_L	v0, PT_STATUS(sp)
+#if defined(CONFIG_CPU_R3000)
+	and	v0, ST0_IEP
+#else
+	and	v0, ST0_IE
+#endif
+	beqz	v0, 1f
+	jal	trace_hardirqs_on
+	b	2f
+1:	jal	trace_hardirqs_off
+2:
+	RESTORE_TEMP
+	RESTORE_AT
+	RESTORE_STATIC
+#endif
+	RESTORE_SOME
+	RESTORE_SP_AND_RET
+	.set	at
+
+work_pending:
+	andi	t0, a2, _TIF_NEED_RESCHED # a2 is preloaded with TI_FLAGS
+	beqz	t0, work_notifysig
+work_resched:
+	TRACE_IRQS_OFF
+	jal	schedule
+
+	local_irq_disable		# make sure need_resched and
+					# signals dont change between
+					# sampling and return
+	LONG_L	a2, TI_FLAGS($28)
+	andi	t0, a2, _TIF_WORK_MASK	# is there any work to be done
+					# other than syscall tracing?
+	beqz	t0, restore_all
+	andi	t0, a2, _TIF_NEED_RESCHED
+	bnez	t0, work_resched
+
+work_notifysig:				# deal with pending signals and
+					# notify-resume requests
+	move	a0, sp
+	li	a1, 0
+	jal	do_notify_resume	# a2 already loaded
+	j	resume_userspace_check
+
+FEXPORT(syscall_exit_partial)
+#ifdef CONFIG_DEBUG_RSEQ
+	move	a0, sp
+	jal	rseq_syscall
+#endif
+	local_irq_disable		# make sure need_resched doesn't
+					# change between and return
+	LONG_L	a2, TI_FLAGS($28)	# current->work
+	li	t0, _TIF_ALLWORK_MASK
+	and	t0, a2
+	beqz	t0, restore_partial
+	SAVE_STATIC
+syscall_exit_work:
+	LONG_L	t0, PT_STATUS(sp)		# returning to kernel mode?
+	andi	t0, t0, KU_USER
+	beqz	t0, resume_kernel
+	li	t0, _TIF_WORK_SYSCALL_EXIT
+	and	t0, a2			# a2 is preloaded with TI_FLAGS
+	beqz	t0, work_pending	# trace bit set?
+	local_irq_enable		# could let syscall_trace_leave()
+					# call schedule() instead
+	TRACE_IRQS_ON
+	move	a0, sp
+	jal	syscall_trace_leave
+	b	resume_userspace
+
+#if defined(CONFIG_CPU_MIPSR2) || defined(CONFIG_CPU_MIPSR5) || \
+    defined(CONFIG_CPU_MIPSR6) || defined(CONFIG_MIPS_MT)
+
+/*
+ * MIPS32R2 Instruction Hazard Barrier - must be called
+ *
+ * For C code use the inline version named instruction_hazard().
+ */
+LEAF(mips_ihb)
+	.set	MIPS_ISA_LEVEL_RAW
+	jr.hb	ra
+	nop
+	END(mips_ihb)
+
+#endif /* CONFIG_CPU_MIPSR2 - CONFIG_CPU_MIPSR6 or CONFIG_MIPS_MT */
diff --git a/arch/mips/kernel/fpu-probe.c b/arch/mips/kernel/fpu-probe.c
new file mode 100644
index 000000000..e689d6a83
--- /dev/null
+++ b/arch/mips/kernel/fpu-probe.c
@@ -0,0 +1,321 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Processor capabilities determination functions.
+ *
+ * Copyright (C) xxxx  the Anonymous
+ * Copyright (C) 1994 - 2006 Ralf Baechle
+ * Copyright (C) 2003, 2004  Maciej W. Rozycki
+ * Copyright (C) 2001, 2004, 2011, 2012	 MIPS Technologies, Inc.
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+
+#include <asm/bugs.h>
+#include <asm/cpu.h>
+#include <asm/cpu-features.h>
+#include <asm/cpu-type.h>
+#include <asm/elf.h>
+#include <asm/fpu.h>
+#include <asm/mipsregs.h>
+
+#include "fpu-probe.h"
+
+/*
+ * Get the FPU Implementation/Revision.
+ */
+static inline unsigned long cpu_get_fpu_id(void)
+{
+	unsigned long tmp, fpu_id;
+
+	tmp = read_c0_status();
+	__enable_fpu(FPU_AS_IS);
+	fpu_id = read_32bit_cp1_register(CP1_REVISION);
+	write_c0_status(tmp);
+	return fpu_id;
+}
+
+/*
+ * Check if the CPU has an external FPU.
+ */
+int __cpu_has_fpu(void)
+{
+	return (cpu_get_fpu_id() & FPIR_IMP_MASK) != FPIR_IMP_NONE;
+}
+
+/*
+ * Determine the FCSR mask for FPU hardware.
+ */
+static inline void cpu_set_fpu_fcsr_mask(struct cpuinfo_mips *c)
+{
+	unsigned long sr, mask, fcsr, fcsr0, fcsr1;
+
+	fcsr = c->fpu_csr31;
+	mask = FPU_CSR_ALL_X | FPU_CSR_ALL_E | FPU_CSR_ALL_S | FPU_CSR_RM;
+
+	sr = read_c0_status();
+	__enable_fpu(FPU_AS_IS);
+
+	fcsr0 = fcsr & mask;
+	write_32bit_cp1_register(CP1_STATUS, fcsr0);
+	fcsr0 = read_32bit_cp1_register(CP1_STATUS);
+
+	fcsr1 = fcsr | ~mask;
+	write_32bit_cp1_register(CP1_STATUS, fcsr1);
+	fcsr1 = read_32bit_cp1_register(CP1_STATUS);
+
+	write_32bit_cp1_register(CP1_STATUS, fcsr);
+
+	write_c0_status(sr);
+
+	c->fpu_msk31 = ~(fcsr0 ^ fcsr1) & ~mask;
+}
+
+/*
+ * Determine the IEEE 754 NaN encodings and ABS.fmt/NEG.fmt execution modes
+ * supported by FPU hardware.
+ */
+static void cpu_set_fpu_2008(struct cpuinfo_mips *c)
+{
+	if (c->isa_level & (MIPS_CPU_ISA_M32R1 | MIPS_CPU_ISA_M64R1 |
+			    MIPS_CPU_ISA_M32R2 | MIPS_CPU_ISA_M64R2 |
+			    MIPS_CPU_ISA_M32R5 | MIPS_CPU_ISA_M64R5 |
+			    MIPS_CPU_ISA_M32R6 | MIPS_CPU_ISA_M64R6)) {
+		unsigned long sr, fir, fcsr, fcsr0, fcsr1;
+
+		sr = read_c0_status();
+		__enable_fpu(FPU_AS_IS);
+
+		fir = read_32bit_cp1_register(CP1_REVISION);
+		if (fir & MIPS_FPIR_HAS2008) {
+			fcsr = read_32bit_cp1_register(CP1_STATUS);
+
+			/*
+			 * MAC2008 toolchain never landed in real world, so
+			 * we're only testing whether it can be disabled and
+			 *  don't try to enabled it.
+			 */
+			fcsr0 = fcsr & ~(FPU_CSR_ABS2008 | FPU_CSR_NAN2008 |
+					 FPU_CSR_MAC2008);
+			write_32bit_cp1_register(CP1_STATUS, fcsr0);
+			fcsr0 = read_32bit_cp1_register(CP1_STATUS);
+
+			fcsr1 = fcsr | FPU_CSR_ABS2008 | FPU_CSR_NAN2008;
+			write_32bit_cp1_register(CP1_STATUS, fcsr1);
+			fcsr1 = read_32bit_cp1_register(CP1_STATUS);
+
+			write_32bit_cp1_register(CP1_STATUS, fcsr);
+
+			if (c->isa_level & (MIPS_CPU_ISA_M32R2 |
+					    MIPS_CPU_ISA_M64R2)) {
+				/*
+				 * The bit for MAC2008 might be reused by R6
+				 * in future, so we only test for R2-R5.
+				 */
+				if (fcsr0 & FPU_CSR_MAC2008)
+					c->options |= MIPS_CPU_MAC_2008_ONLY;
+			}
+
+			if (!(fcsr0 & FPU_CSR_NAN2008))
+				c->options |= MIPS_CPU_NAN_LEGACY;
+			if (fcsr1 & FPU_CSR_NAN2008)
+				c->options |= MIPS_CPU_NAN_2008;
+
+			if ((fcsr0 ^ fcsr1) & FPU_CSR_ABS2008)
+				c->fpu_msk31 &= ~FPU_CSR_ABS2008;
+			else
+				c->fpu_csr31 |= fcsr & FPU_CSR_ABS2008;
+
+			if ((fcsr0 ^ fcsr1) & FPU_CSR_NAN2008)
+				c->fpu_msk31 &= ~FPU_CSR_NAN2008;
+			else
+				c->fpu_csr31 |= fcsr & FPU_CSR_NAN2008;
+		} else {
+			c->options |= MIPS_CPU_NAN_LEGACY;
+		}
+
+		write_c0_status(sr);
+	} else {
+		c->options |= MIPS_CPU_NAN_LEGACY;
+	}
+}
+
+/*
+ * IEEE 754 conformance mode to use.  Affects the NaN encoding and the
+ * ABS.fmt/NEG.fmt execution mode.
+ */
+static enum { STRICT, LEGACY, STD2008, RELAXED } ieee754 = STRICT;
+
+/*
+ * Set the IEEE 754 NaN encodings and the ABS.fmt/NEG.fmt execution modes
+ * to support by the FPU emulator according to the IEEE 754 conformance
+ * mode selected.  Note that "relaxed" straps the emulator so that it
+ * allows 2008-NaN binaries even for legacy processors.
+ */
+static void cpu_set_nofpu_2008(struct cpuinfo_mips *c)
+{
+	c->options &= ~(MIPS_CPU_NAN_2008 | MIPS_CPU_NAN_LEGACY);
+	c->fpu_csr31 &= ~(FPU_CSR_ABS2008 | FPU_CSR_NAN2008);
+	c->fpu_msk31 &= ~(FPU_CSR_ABS2008 | FPU_CSR_NAN2008);
+
+	switch (ieee754) {
+	case STRICT:
+		if (c->isa_level & (MIPS_CPU_ISA_M32R1 | MIPS_CPU_ISA_M64R1 |
+				    MIPS_CPU_ISA_M32R2 | MIPS_CPU_ISA_M64R2 |
+				    MIPS_CPU_ISA_M32R5 | MIPS_CPU_ISA_M64R5 |
+				    MIPS_CPU_ISA_M32R6 | MIPS_CPU_ISA_M64R6)) {
+			c->options |= MIPS_CPU_NAN_2008 | MIPS_CPU_NAN_LEGACY;
+		} else {
+			c->options |= MIPS_CPU_NAN_LEGACY;
+			c->fpu_msk31 |= FPU_CSR_ABS2008 | FPU_CSR_NAN2008;
+		}
+		break;
+	case LEGACY:
+		c->options |= MIPS_CPU_NAN_LEGACY;
+		c->fpu_msk31 |= FPU_CSR_ABS2008 | FPU_CSR_NAN2008;
+		break;
+	case STD2008:
+		c->options |= MIPS_CPU_NAN_2008;
+		c->fpu_csr31 |= FPU_CSR_ABS2008 | FPU_CSR_NAN2008;
+		c->fpu_msk31 |= FPU_CSR_ABS2008 | FPU_CSR_NAN2008;
+		break;
+	case RELAXED:
+		c->options |= MIPS_CPU_NAN_2008 | MIPS_CPU_NAN_LEGACY;
+		break;
+	}
+}
+
+/*
+ * Override the IEEE 754 NaN encoding and ABS.fmt/NEG.fmt execution mode
+ * according to the "ieee754=" parameter.
+ */
+static void cpu_set_nan_2008(struct cpuinfo_mips *c)
+{
+	switch (ieee754) {
+	case STRICT:
+		mips_use_nan_legacy = !!cpu_has_nan_legacy;
+		mips_use_nan_2008 = !!cpu_has_nan_2008;
+		break;
+	case LEGACY:
+		mips_use_nan_legacy = !!cpu_has_nan_legacy;
+		mips_use_nan_2008 = !cpu_has_nan_legacy;
+		break;
+	case STD2008:
+		mips_use_nan_legacy = !cpu_has_nan_2008;
+		mips_use_nan_2008 = !!cpu_has_nan_2008;
+		break;
+	case RELAXED:
+		mips_use_nan_legacy = true;
+		mips_use_nan_2008 = true;
+		break;
+	}
+}
+
+/*
+ * IEEE 754 NaN encoding and ABS.fmt/NEG.fmt execution mode override
+ * settings:
+ *
+ * strict:  accept binaries that request a NaN encoding supported by the FPU
+ * legacy:  only accept legacy-NaN binaries
+ * 2008:    only accept 2008-NaN binaries
+ * relaxed: accept any binaries regardless of whether supported by the FPU
+ */
+static int __init ieee754_setup(char *s)
+{
+	if (!s)
+		return -1;
+	else if (!strcmp(s, "strict"))
+		ieee754 = STRICT;
+	else if (!strcmp(s, "legacy"))
+		ieee754 = LEGACY;
+	else if (!strcmp(s, "2008"))
+		ieee754 = STD2008;
+	else if (!strcmp(s, "relaxed"))
+		ieee754 = RELAXED;
+	else
+		return -1;
+
+	if (!(boot_cpu_data.options & MIPS_CPU_FPU))
+		cpu_set_nofpu_2008(&boot_cpu_data);
+	cpu_set_nan_2008(&boot_cpu_data);
+
+	return 0;
+}
+
+early_param("ieee754", ieee754_setup);
+
+/*
+ * Set the FIR feature flags for the FPU emulator.
+ */
+static void cpu_set_nofpu_id(struct cpuinfo_mips *c)
+{
+	u32 value;
+
+	value = 0;
+	if (c->isa_level & (MIPS_CPU_ISA_M32R1 | MIPS_CPU_ISA_M64R1 |
+			    MIPS_CPU_ISA_M32R2 | MIPS_CPU_ISA_M64R2 |
+			    MIPS_CPU_ISA_M32R5 | MIPS_CPU_ISA_M64R5 |
+			    MIPS_CPU_ISA_M32R6 | MIPS_CPU_ISA_M64R6))
+		value |= MIPS_FPIR_D | MIPS_FPIR_S;
+	if (c->isa_level & (MIPS_CPU_ISA_M32R2 | MIPS_CPU_ISA_M64R2 |
+			    MIPS_CPU_ISA_M32R5 | MIPS_CPU_ISA_M64R5 |
+			    MIPS_CPU_ISA_M32R6 | MIPS_CPU_ISA_M64R6))
+		value |= MIPS_FPIR_F64 | MIPS_FPIR_L | MIPS_FPIR_W;
+	if (c->options & MIPS_CPU_NAN_2008)
+		value |= MIPS_FPIR_HAS2008;
+	c->fpu_id = value;
+}
+
+/* Determined FPU emulator mask to use for the boot CPU with "nofpu".  */
+static unsigned int mips_nofpu_msk31;
+
+/*
+ * Set options for FPU hardware.
+ */
+void cpu_set_fpu_opts(struct cpuinfo_mips *c)
+{
+	c->fpu_id = cpu_get_fpu_id();
+	mips_nofpu_msk31 = c->fpu_msk31;
+
+	if (c->isa_level & (MIPS_CPU_ISA_M32R1 | MIPS_CPU_ISA_M64R1 |
+			    MIPS_CPU_ISA_M32R2 | MIPS_CPU_ISA_M64R2 |
+			    MIPS_CPU_ISA_M32R5 | MIPS_CPU_ISA_M64R5 |
+			    MIPS_CPU_ISA_M32R6 | MIPS_CPU_ISA_M64R6)) {
+		if (c->fpu_id & MIPS_FPIR_3D)
+			c->ases |= MIPS_ASE_MIPS3D;
+		if (c->fpu_id & MIPS_FPIR_UFRP)
+			c->options |= MIPS_CPU_UFR;
+		if (c->fpu_id & MIPS_FPIR_FREP)
+			c->options |= MIPS_CPU_FRE;
+	}
+
+	cpu_set_fpu_fcsr_mask(c);
+	cpu_set_fpu_2008(c);
+	cpu_set_nan_2008(c);
+}
+
+/*
+ * Set options for the FPU emulator.
+ */
+void cpu_set_nofpu_opts(struct cpuinfo_mips *c)
+{
+	c->options &= ~MIPS_CPU_FPU;
+	c->fpu_msk31 = mips_nofpu_msk31;
+
+	cpu_set_nofpu_2008(c);
+	cpu_set_nan_2008(c);
+	cpu_set_nofpu_id(c);
+}
+
+int mips_fpu_disabled;
+
+static int __init fpu_disable(char *s)
+{
+	cpu_set_nofpu_opts(&boot_cpu_data);
+	mips_fpu_disabled = 1;
+
+	return 1;
+}
+
+__setup("nofpu", fpu_disable);
+
diff --git a/arch/mips/kernel/fpu-probe.h b/arch/mips/kernel/fpu-probe.h
new file mode 100644
index 000000000..951ce5089
--- /dev/null
+++ b/arch/mips/kernel/fpu-probe.h
@@ -0,0 +1,40 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+
+#include <linux/kernel.h>
+
+#include <asm/cpu.h>
+#include <asm/cpu-info.h>
+
+#ifdef CONFIG_MIPS_FP_SUPPORT
+
+extern int mips_fpu_disabled;
+
+int __cpu_has_fpu(void);
+void cpu_set_fpu_opts(struct cpuinfo_mips *c);
+void cpu_set_nofpu_opts(struct cpuinfo_mips *c);
+
+#else /* !CONFIG_MIPS_FP_SUPPORT */
+
+#define mips_fpu_disabled 1
+
+static inline unsigned long cpu_get_fpu_id(void)
+{
+	return FPIR_IMP_NONE;
+}
+
+static inline int __cpu_has_fpu(void)
+{
+	return 0;
+}
+
+static inline void cpu_set_fpu_opts(struct cpuinfo_mips *c)
+{
+	/* no-op */
+}
+
+static inline void cpu_set_nofpu_opts(struct cpuinfo_mips *c)
+{
+	/* no-op */
+}
+
+#endif /* CONFIG_MIPS_FP_SUPPORT */
diff --git a/arch/mips/kernel/ftrace.c b/arch/mips/kernel/ftrace.c
new file mode 100644
index 000000000..8c401e423
--- /dev/null
+++ b/arch/mips/kernel/ftrace.c
@@ -0,0 +1,402 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Code for replacing ftrace calls with jumps.
+ *
+ * Copyright (C) 2007-2008 Steven Rostedt <srostedt@redhat.com>
+ * Copyright (C) 2009, 2010 DSLab, Lanzhou University, China
+ * Author: Wu Zhangjin <wuzhangjin@gmail.com>
+ *
+ * Thanks goes to Steven Rostedt for writing the original x86 version.
+ */
+
+#include <linux/uaccess.h>
+#include <linux/init.h>
+#include <linux/ftrace.h>
+#include <linux/syscalls.h>
+
+#include <asm/asm.h>
+#include <asm/asm-offsets.h>
+#include <asm/cacheflush.h>
+#include <asm/syscall.h>
+#include <asm/uasm.h>
+#include <asm/unistd.h>
+
+#include <asm-generic/sections.h>
+
+#if defined(KBUILD_MCOUNT_RA_ADDRESS) && defined(CONFIG_32BIT)
+#define MCOUNT_OFFSET_INSNS 5
+#else
+#define MCOUNT_OFFSET_INSNS 4
+#endif
+
+#ifdef CONFIG_DYNAMIC_FTRACE
+
+/* Arch override because MIPS doesn't need to run this from stop_machine() */
+void arch_ftrace_update_code(int command)
+{
+	ftrace_modify_all_code(command);
+}
+
+#define JAL 0x0c000000		/* jump & link: ip --> ra, jump to target */
+#define ADDR_MASK 0x03ffffff	/*  op_code|addr : 31...26|25 ....0 */
+#define JUMP_RANGE_MASK ((1UL << 28) - 1)
+
+#define INSN_NOP 0x00000000	/* nop */
+#define INSN_JAL(addr)	\
+	((unsigned int)(JAL | (((addr) >> 2) & ADDR_MASK)))
+
+static unsigned int insn_jal_ftrace_caller __read_mostly;
+static unsigned int insn_la_mcount[2] __read_mostly;
+static unsigned int insn_j_ftrace_graph_caller __maybe_unused __read_mostly;
+
+static inline void ftrace_dyn_arch_init_insns(void)
+{
+	u32 *buf;
+	unsigned int v1;
+
+	/* la v1, _mcount */
+	v1 = 3;
+	buf = (u32 *)&insn_la_mcount[0];
+	UASM_i_LA(&buf, v1, MCOUNT_ADDR);
+
+	/* jal (ftrace_caller + 8), jump over the first two instruction */
+	buf = (u32 *)&insn_jal_ftrace_caller;
+	uasm_i_jal(&buf, (FTRACE_ADDR + 8) & JUMP_RANGE_MASK);
+
+#ifdef CONFIG_FUNCTION_GRAPH_TRACER
+	/* j ftrace_graph_caller */
+	buf = (u32 *)&insn_j_ftrace_graph_caller;
+	uasm_i_j(&buf, (unsigned long)ftrace_graph_caller & JUMP_RANGE_MASK);
+#endif
+}
+
+static int ftrace_modify_code(unsigned long ip, unsigned int new_code)
+{
+	int faulted;
+
+	/* *(unsigned int *)ip = new_code; */
+	safe_store_code(new_code, ip, faulted);
+
+	if (unlikely(faulted))
+		return -EFAULT;
+
+	flush_icache_range(ip, ip + 8);
+
+	return 0;
+}
+
+#ifndef CONFIG_64BIT
+static int ftrace_modify_code_2(unsigned long ip, unsigned int new_code1,
+				unsigned int new_code2)
+{
+	int faulted;
+
+	safe_store_code(new_code1, ip, faulted);
+	if (unlikely(faulted))
+		return -EFAULT;
+
+	ip += 4;
+	safe_store_code(new_code2, ip, faulted);
+	if (unlikely(faulted))
+		return -EFAULT;
+
+	ip -= 4;
+	flush_icache_range(ip, ip + 8);
+
+	return 0;
+}
+
+static int ftrace_modify_code_2r(unsigned long ip, unsigned int new_code1,
+				 unsigned int new_code2)
+{
+	int faulted;
+
+	ip += 4;
+	safe_store_code(new_code2, ip, faulted);
+	if (unlikely(faulted))
+		return -EFAULT;
+
+	ip -= 4;
+	safe_store_code(new_code1, ip, faulted);
+	if (unlikely(faulted))
+		return -EFAULT;
+
+	flush_icache_range(ip, ip + 8);
+
+	return 0;
+}
+#endif
+
+/*
+ * The details about the calling site of mcount on MIPS
+ *
+ * 1. For kernel:
+ *
+ * move at, ra
+ * jal _mcount		--> nop
+ *  sub sp, sp, 8	--> nop  (CONFIG_32BIT)
+ *
+ * 2. For modules:
+ *
+ * 2.1 For KBUILD_MCOUNT_RA_ADDRESS and CONFIG_32BIT
+ *
+ * lui v1, hi_16bit_of_mcount	     --> b 1f (0x10000005)
+ * addiu v1, v1, low_16bit_of_mcount --> nop  (CONFIG_32BIT)
+ * move at, ra
+ * move $12, ra_address
+ * jalr v1
+ *  sub sp, sp, 8
+ *				    1: offset = 5 instructions
+ * 2.2 For the Other situations
+ *
+ * lui v1, hi_16bit_of_mcount	     --> b 1f (0x10000004)
+ * addiu v1, v1, low_16bit_of_mcount --> nop  (CONFIG_32BIT)
+ * move at, ra
+ * jalr v1
+ *  nop | move $12, ra_address | sub sp, sp, 8
+ *				    1: offset = 4 instructions
+ */
+
+#define INSN_B_1F (0x10000000 | MCOUNT_OFFSET_INSNS)
+
+int ftrace_make_nop(struct module *mod,
+		    struct dyn_ftrace *rec, unsigned long addr)
+{
+	unsigned int new;
+	unsigned long ip = rec->ip;
+
+	/*
+	 * If ip is in kernel space, no long call, otherwise, long call is
+	 * needed.
+	 */
+	new = core_kernel_text(ip) ? INSN_NOP : INSN_B_1F;
+#ifdef CONFIG_64BIT
+	return ftrace_modify_code(ip, new);
+#else
+	/*
+	 * On 32 bit MIPS platforms, gcc adds a stack adjust
+	 * instruction in the delay slot after the branch to
+	 * mcount and expects mcount to restore the sp on return.
+	 * This is based on a legacy API and does nothing but
+	 * waste instructions so it's being removed at runtime.
+	 */
+	return ftrace_modify_code_2(ip, new, INSN_NOP);
+#endif
+}
+
+int ftrace_make_call(struct dyn_ftrace *rec, unsigned long addr)
+{
+	unsigned int new;
+	unsigned long ip = rec->ip;
+
+	new = core_kernel_text(ip) ? insn_jal_ftrace_caller : insn_la_mcount[0];
+
+#ifdef CONFIG_64BIT
+	return ftrace_modify_code(ip, new);
+#else
+	return ftrace_modify_code_2r(ip, new, core_kernel_text(ip) ?
+						INSN_NOP : insn_la_mcount[1]);
+#endif
+}
+
+#define FTRACE_CALL_IP ((unsigned long)(&ftrace_call))
+
+int ftrace_update_ftrace_func(ftrace_func_t func)
+{
+	unsigned int new;
+
+	new = INSN_JAL((unsigned long)func);
+
+	return ftrace_modify_code(FTRACE_CALL_IP, new);
+}
+
+int __init ftrace_dyn_arch_init(void)
+{
+	/* Encode the instructions when booting */
+	ftrace_dyn_arch_init_insns();
+
+	/* Remove "b ftrace_stub" to ensure ftrace_caller() is executed */
+	ftrace_modify_code(MCOUNT_ADDR, INSN_NOP);
+
+	return 0;
+}
+#endif	/* CONFIG_DYNAMIC_FTRACE */
+
+#ifdef CONFIG_FUNCTION_GRAPH_TRACER
+
+#ifdef CONFIG_DYNAMIC_FTRACE
+
+extern void ftrace_graph_call(void);
+#define FTRACE_GRAPH_CALL_IP	((unsigned long)(&ftrace_graph_call))
+
+int ftrace_enable_ftrace_graph_caller(void)
+{
+	return ftrace_modify_code(FTRACE_GRAPH_CALL_IP,
+			insn_j_ftrace_graph_caller);
+}
+
+int ftrace_disable_ftrace_graph_caller(void)
+{
+	return ftrace_modify_code(FTRACE_GRAPH_CALL_IP, INSN_NOP);
+}
+
+#endif	/* CONFIG_DYNAMIC_FTRACE */
+
+#ifndef KBUILD_MCOUNT_RA_ADDRESS
+
+#define S_RA_SP (0xafbf << 16)	/* s{d,w} ra, offset(sp) */
+#define S_R_SP	(0xafb0 << 16)	/* s{d,w} R, offset(sp) */
+#define OFFSET_MASK	0xffff	/* stack offset range: 0 ~ PT_SIZE */
+
+unsigned long ftrace_get_parent_ra_addr(unsigned long self_ra, unsigned long
+		old_parent_ra, unsigned long parent_ra_addr, unsigned long fp)
+{
+	unsigned long sp, ip, tmp;
+	unsigned int code;
+	int faulted;
+
+	/*
+	 * For module, move the ip from the return address after the
+	 * instruction "lui v1, hi_16bit_of_mcount"(offset is 24), but for
+	 * kernel, move after the instruction "move ra, at"(offset is 16)
+	 */
+	ip = self_ra - (core_kernel_text(self_ra) ? 16 : 24);
+
+	/*
+	 * search the text until finding the non-store instruction or "s{d,w}
+	 * ra, offset(sp)" instruction
+	 */
+	do {
+		/* get the code at "ip": code = *(unsigned int *)ip; */
+		safe_load_code(code, ip, faulted);
+
+		if (unlikely(faulted))
+			return 0;
+		/*
+		 * If we hit the non-store instruction before finding where the
+		 * ra is stored, then this is a leaf function and it does not
+		 * store the ra on the stack
+		 */
+		if ((code & S_R_SP) != S_R_SP)
+			return parent_ra_addr;
+
+		/* Move to the next instruction */
+		ip -= 4;
+	} while ((code & S_RA_SP) != S_RA_SP);
+
+	sp = fp + (code & OFFSET_MASK);
+
+	/* tmp = *(unsigned long *)sp; */
+	safe_load_stack(tmp, sp, faulted);
+	if (unlikely(faulted))
+		return 0;
+
+	if (tmp == old_parent_ra)
+		return sp;
+	return 0;
+}
+
+#endif	/* !KBUILD_MCOUNT_RA_ADDRESS */
+
+/*
+ * Hook the return address and push it in the stack of return addrs
+ * in current thread info.
+ */
+void prepare_ftrace_return(unsigned long *parent_ra_addr, unsigned long self_ra,
+			   unsigned long fp)
+{
+	unsigned long old_parent_ra;
+	unsigned long return_hooker = (unsigned long)
+	    &return_to_handler;
+	int faulted, insns;
+
+	if (unlikely(ftrace_graph_is_dead()))
+		return;
+
+	if (unlikely(atomic_read(&current->tracing_graph_pause)))
+		return;
+
+	/*
+	 * "parent_ra_addr" is the stack address where the return address of
+	 * the caller of _mcount is saved.
+	 *
+	 * If gcc < 4.5, a leaf function does not save the return address
+	 * in the stack address, so we "emulate" one in _mcount's stack space,
+	 * and hijack it directly.
+	 * For a non-leaf function, it does save the return address to its own
+	 * stack space, so we can not hijack it directly, but need to find the
+	 * real stack address, which is done by ftrace_get_parent_addr().
+	 *
+	 * If gcc >= 4.5, with the new -mmcount-ra-address option, for a
+	 * non-leaf function, the location of the return address will be saved
+	 * to $12 for us.
+	 * For a leaf function, it just puts a zero into $12, so we handle
+	 * it in ftrace_graph_caller() of mcount.S.
+	 */
+
+	/* old_parent_ra = *parent_ra_addr; */
+	safe_load_stack(old_parent_ra, parent_ra_addr, faulted);
+	if (unlikely(faulted))
+		goto out;
+#ifndef KBUILD_MCOUNT_RA_ADDRESS
+	parent_ra_addr = (unsigned long *)ftrace_get_parent_ra_addr(self_ra,
+			old_parent_ra, (unsigned long)parent_ra_addr, fp);
+	/*
+	 * If fails when getting the stack address of the non-leaf function's
+	 * ra, stop function graph tracer and return
+	 */
+	if (parent_ra_addr == NULL)
+		goto out;
+#endif
+	/* *parent_ra_addr = return_hooker; */
+	safe_store_stack(return_hooker, parent_ra_addr, faulted);
+	if (unlikely(faulted))
+		goto out;
+
+	/*
+	 * Get the recorded ip of the current mcount calling site in the
+	 * __mcount_loc section, which will be used to filter the function
+	 * entries configured through the tracing/set_graph_function interface.
+	 */
+
+	insns = core_kernel_text(self_ra) ? 2 : MCOUNT_OFFSET_INSNS + 1;
+	self_ra -= (MCOUNT_INSN_SIZE * insns);
+
+	if (function_graph_enter(old_parent_ra, self_ra, fp, NULL))
+		*parent_ra_addr = old_parent_ra;
+	return;
+out:
+	ftrace_graph_stop();
+	WARN_ON(1);
+}
+#endif	/* CONFIG_FUNCTION_GRAPH_TRACER */
+
+#ifdef CONFIG_FTRACE_SYSCALLS
+
+#ifdef CONFIG_32BIT
+unsigned long __init arch_syscall_addr(int nr)
+{
+	return (unsigned long)sys_call_table[nr - __NR_O32_Linux];
+}
+#endif
+
+#ifdef CONFIG_64BIT
+
+unsigned long __init arch_syscall_addr(int nr)
+{
+#ifdef CONFIG_MIPS32_N32
+	if (nr >= __NR_N32_Linux && nr < __NR_N32_Linux + __NR_N32_Linux_syscalls)
+		return (unsigned long)sysn32_call_table[nr - __NR_N32_Linux];
+#endif
+	if (nr >= __NR_64_Linux  && nr < __NR_64_Linux + __NR_64_Linux_syscalls)
+		return (unsigned long)sys_call_table[nr - __NR_64_Linux];
+#ifdef CONFIG_MIPS32_O32
+	if (nr >= __NR_O32_Linux && nr < __NR_O32_Linux + __NR_O32_Linux_syscalls)
+		return (unsigned long)sys32_call_table[nr - __NR_O32_Linux];
+#endif
+
+	return (unsigned long) &sys_ni_syscall;
+}
+#endif
+
+#endif /* CONFIG_FTRACE_SYSCALLS */
diff --git a/arch/mips/kernel/genex.S b/arch/mips/kernel/genex.S
new file mode 100644
index 000000000..3425df601
--- /dev/null
+++ b/arch/mips/kernel/genex.S
@@ -0,0 +1,681 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994 - 2000, 2001, 2003 Ralf Baechle
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ * Copyright (C) 2002, 2007  Maciej W. Rozycki
+ * Copyright (C) 2001, 2012 MIPS Technologies, Inc.  All rights reserved.
+ */
+#include <linux/init.h>
+
+#include <asm/asm.h>
+#include <asm/asmmacro.h>
+#include <asm/cacheops.h>
+#include <asm/irqflags.h>
+#include <asm/regdef.h>
+#include <asm/fpregdef.h>
+#include <asm/mipsregs.h>
+#include <asm/stackframe.h>
+#include <asm/sync.h>
+#include <asm/thread_info.h>
+
+	__INIT
+
+/*
+ * General exception vector for all other CPUs.
+ *
+ * Be careful when changing this, it has to be at most 128 bytes
+ * to fit into space reserved for the exception handler.
+ */
+NESTED(except_vec3_generic, 0, sp)
+	.set	push
+	.set	noat
+	mfc0	k1, CP0_CAUSE
+	andi	k1, k1, 0x7c
+#ifdef CONFIG_64BIT
+	dsll	k1, k1, 1
+#endif
+	PTR_L	k0, exception_handlers(k1)
+	jr	k0
+	.set	pop
+	END(except_vec3_generic)
+
+/*
+ * General exception handler for CPUs with virtual coherency exception.
+ *
+ * Be careful when changing this, it has to be at most 256 (as a special
+ * exception) bytes to fit into space reserved for the exception handler.
+ */
+NESTED(except_vec3_r4000, 0, sp)
+	.set	push
+	.set	arch=r4000
+	.set	noat
+	mfc0	k1, CP0_CAUSE
+	li	k0, 31<<2
+	andi	k1, k1, 0x7c
+	.set	push
+	.set	noreorder
+	.set	nomacro
+	beq	k1, k0, handle_vced
+	 li	k0, 14<<2
+	beq	k1, k0, handle_vcei
+#ifdef CONFIG_64BIT
+	 dsll	k1, k1, 1
+#endif
+	.set	pop
+	PTR_L	k0, exception_handlers(k1)
+	jr	k0
+
+	/*
+	 * Big shit, we now may have two dirty primary cache lines for the same
+	 * physical address.  We can safely invalidate the line pointed to by
+	 * c0_badvaddr because after return from this exception handler the
+	 * load / store will be re-executed.
+	 */
+handle_vced:
+	MFC0	k0, CP0_BADVADDR
+	li	k1, -4					# Is this ...
+	and	k0, k1					# ... really needed?
+	mtc0	zero, CP0_TAGLO
+	cache	Index_Store_Tag_D, (k0)
+	cache	Hit_Writeback_Inv_SD, (k0)
+#ifdef CONFIG_PROC_FS
+	PTR_LA	k0, vced_count
+	lw	k1, (k0)
+	addiu	k1, 1
+	sw	k1, (k0)
+#endif
+	eret
+
+handle_vcei:
+	MFC0	k0, CP0_BADVADDR
+	cache	Hit_Writeback_Inv_SD, (k0)		# also cleans pi
+#ifdef CONFIG_PROC_FS
+	PTR_LA	k0, vcei_count
+	lw	k1, (k0)
+	addiu	k1, 1
+	sw	k1, (k0)
+#endif
+	eret
+	.set	pop
+	END(except_vec3_r4000)
+
+	__FINIT
+
+	.align	5	/* 32 byte rollback region */
+LEAF(__r4k_wait)
+	.set	push
+	.set	noreorder
+	/* start of rollback region */
+	LONG_L	t0, TI_FLAGS($28)
+	nop
+	andi	t0, _TIF_NEED_RESCHED
+	bnez	t0, 1f
+	 nop
+	nop
+	nop
+#ifdef CONFIG_CPU_MICROMIPS
+	nop
+	nop
+	nop
+	nop
+#endif
+	.set	MIPS_ISA_ARCH_LEVEL_RAW
+	wait
+	/* end of rollback region (the region size must be power of two) */
+1:
+	jr	ra
+	 nop
+	.set	pop
+	END(__r4k_wait)
+
+	.macro	BUILD_ROLLBACK_PROLOGUE handler
+	FEXPORT(rollback_\handler)
+	.set	push
+	.set	noat
+	MFC0	k0, CP0_EPC
+	PTR_LA	k1, __r4k_wait
+	ori	k0, 0x1f	/* 32 byte rollback region */
+	xori	k0, 0x1f
+	bne	k0, k1, \handler
+	MTC0	k0, CP0_EPC
+	.set pop
+	.endm
+
+	.align	5
+BUILD_ROLLBACK_PROLOGUE handle_int
+NESTED(handle_int, PT_SIZE, sp)
+	.cfi_signal_frame
+#ifdef CONFIG_TRACE_IRQFLAGS
+	/*
+	 * Check to see if the interrupted code has just disabled
+	 * interrupts and ignore this interrupt for now if so.
+	 *
+	 * local_irq_disable() disables interrupts and then calls
+	 * trace_hardirqs_off() to track the state. If an interrupt is taken
+	 * after interrupts are disabled but before the state is updated
+	 * it will appear to restore_all that it is incorrectly returning with
+	 * interrupts disabled
+	 */
+	.set	push
+	.set	noat
+	mfc0	k0, CP0_STATUS
+#if defined(CONFIG_CPU_R3000)
+	and	k0, ST0_IEP
+	bnez	k0, 1f
+
+	mfc0	k0, CP0_EPC
+	.set	noreorder
+	j	k0
+	 rfe
+#else
+	and	k0, ST0_IE
+	bnez	k0, 1f
+
+	eret
+#endif
+1:
+	.set pop
+#endif
+	SAVE_ALL docfi=1
+	CLI
+	TRACE_IRQS_OFF
+
+	LONG_L	s0, TI_REGS($28)
+	LONG_S	sp, TI_REGS($28)
+
+	/*
+	 * SAVE_ALL ensures we are using a valid kernel stack for the thread.
+	 * Check if we are already using the IRQ stack.
+	 */
+	move	s1, sp # Preserve the sp
+
+	/* Get IRQ stack for this CPU */
+	ASM_CPUID_MFC0	k0, ASM_SMP_CPUID_REG
+#if defined(CONFIG_32BIT) || defined(KBUILD_64BIT_SYM32)
+	lui	k1, %hi(irq_stack)
+#else
+	lui	k1, %highest(irq_stack)
+	daddiu	k1, %higher(irq_stack)
+	dsll	k1, 16
+	daddiu	k1, %hi(irq_stack)
+	dsll	k1, 16
+#endif
+	LONG_SRL	k0, SMP_CPUID_PTRSHIFT
+	LONG_ADDU	k1, k0
+	LONG_L	t0, %lo(irq_stack)(k1)
+
+	# Check if already on IRQ stack
+	PTR_LI	t1, ~(_THREAD_SIZE-1)
+	and	t1, t1, sp
+	beq	t0, t1, 2f
+
+	/* Switch to IRQ stack */
+	li	t1, _IRQ_STACK_START
+	PTR_ADD sp, t0, t1
+
+	/* Save task's sp on IRQ stack so that unwinding can follow it */
+	LONG_S	s1, 0(sp)
+2:
+	jal	plat_irq_dispatch
+
+	/* Restore sp */
+	move	sp, s1
+
+	j	ret_from_irq
+#ifdef CONFIG_CPU_MICROMIPS
+	nop
+#endif
+	END(handle_int)
+
+	__INIT
+
+/*
+ * Special interrupt vector for MIPS64 ISA & embedded MIPS processors.
+ * This is a dedicated interrupt exception vector which reduces the
+ * interrupt processing overhead.  The jump instruction will be replaced
+ * at the initialization time.
+ *
+ * Be careful when changing this, it has to be at most 128 bytes
+ * to fit into space reserved for the exception handler.
+ */
+NESTED(except_vec4, 0, sp)
+1:	j	1b			/* Dummy, will be replaced */
+	END(except_vec4)
+
+/*
+ * EJTAG debug exception handler.
+ * The EJTAG debug exception entry point is 0xbfc00480, which
+ * normally is in the boot PROM, so the boot PROM must do an
+ * unconditional jump to this vector.
+ */
+NESTED(except_vec_ejtag_debug, 0, sp)
+	j	ejtag_debug_handler
+#ifdef CONFIG_CPU_MICROMIPS
+	 nop
+#endif
+	END(except_vec_ejtag_debug)
+
+	__FINIT
+
+/*
+ * Vectored interrupt handler.
+ * This prototype is copied to ebase + n*IntCtl.VS and patched
+ * to invoke the handler
+ */
+BUILD_ROLLBACK_PROLOGUE except_vec_vi
+NESTED(except_vec_vi, 0, sp)
+	SAVE_SOME docfi=1
+	SAVE_AT docfi=1
+	.set	push
+	.set	noreorder
+	PTR_LA	v1, except_vec_vi_handler
+FEXPORT(except_vec_vi_lui)
+	lui	v0, 0		/* Patched */
+	jr	v1
+FEXPORT(except_vec_vi_ori)
+	 ori	v0, 0		/* Patched */
+	.set	pop
+	END(except_vec_vi)
+EXPORT(except_vec_vi_end)
+
+/*
+ * Common Vectored Interrupt code
+ * Complete the register saves and invoke the handler which is passed in $v0
+ */
+NESTED(except_vec_vi_handler, 0, sp)
+	SAVE_TEMP
+	SAVE_STATIC
+	CLI
+#ifdef CONFIG_TRACE_IRQFLAGS
+	move	s0, v0
+	TRACE_IRQS_OFF
+	move	v0, s0
+#endif
+
+	LONG_L	s0, TI_REGS($28)
+	LONG_S	sp, TI_REGS($28)
+
+	/*
+	 * SAVE_ALL ensures we are using a valid kernel stack for the thread.
+	 * Check if we are already using the IRQ stack.
+	 */
+	move	s1, sp # Preserve the sp
+
+	/* Get IRQ stack for this CPU */
+	ASM_CPUID_MFC0	k0, ASM_SMP_CPUID_REG
+#if defined(CONFIG_32BIT) || defined(KBUILD_64BIT_SYM32)
+	lui	k1, %hi(irq_stack)
+#else
+	lui	k1, %highest(irq_stack)
+	daddiu	k1, %higher(irq_stack)
+	dsll	k1, 16
+	daddiu	k1, %hi(irq_stack)
+	dsll	k1, 16
+#endif
+	LONG_SRL	k0, SMP_CPUID_PTRSHIFT
+	LONG_ADDU	k1, k0
+	LONG_L	t0, %lo(irq_stack)(k1)
+
+	# Check if already on IRQ stack
+	PTR_LI	t1, ~(_THREAD_SIZE-1)
+	and	t1, t1, sp
+	beq	t0, t1, 2f
+
+	/* Switch to IRQ stack */
+	li	t1, _IRQ_STACK_START
+	PTR_ADD sp, t0, t1
+
+	/* Save task's sp on IRQ stack so that unwinding can follow it */
+	LONG_S	s1, 0(sp)
+2:
+	jalr	v0
+
+	/* Restore sp */
+	move	sp, s1
+
+	j	ret_from_irq
+	END(except_vec_vi_handler)
+
+/*
+ * EJTAG debug exception handler.
+ */
+NESTED(ejtag_debug_handler, PT_SIZE, sp)
+	.set	push
+	.set	noat
+	MTC0	k0, CP0_DESAVE
+	mfc0	k0, CP0_DEBUG
+
+	andi	k0, k0, MIPS_DEBUG_DBP	# Check for SDBBP.
+	beqz	k0, ejtag_return
+
+#ifdef CONFIG_SMP
+1:	PTR_LA	k0, ejtag_debug_buffer_spinlock
+	__SYNC(full, loongson3_war)
+2:	ll	k0, 0(k0)
+	bnez	k0, 2b
+	PTR_LA	k0, ejtag_debug_buffer_spinlock
+	sc	k0, 0(k0)
+	beqz	k0, 1b
+# ifdef CONFIG_WEAK_REORDERING_BEYOND_LLSC
+	sync
+# endif
+
+	PTR_LA	k0, ejtag_debug_buffer
+	LONG_S	k1, 0(k0)
+
+	ASM_CPUID_MFC0 k1, ASM_SMP_CPUID_REG
+	PTR_SRL	k1, SMP_CPUID_PTRSHIFT
+	PTR_SLL	k1, LONGLOG
+	PTR_LA	k0, ejtag_debug_buffer_per_cpu
+	PTR_ADDU k0, k1
+
+	PTR_LA	k1, ejtag_debug_buffer
+	LONG_L	k1, 0(k1)
+	LONG_S	k1, 0(k0)
+
+	PTR_LA	k0, ejtag_debug_buffer_spinlock
+	sw	zero, 0(k0)
+#else
+	PTR_LA	k0, ejtag_debug_buffer
+	LONG_S	k1, 0(k0)
+#endif
+
+	SAVE_ALL
+	move	a0, sp
+	jal	ejtag_exception_handler
+	RESTORE_ALL
+
+#ifdef CONFIG_SMP
+	ASM_CPUID_MFC0 k1, ASM_SMP_CPUID_REG
+	PTR_SRL	k1, SMP_CPUID_PTRSHIFT
+	PTR_SLL	k1, LONGLOG
+	PTR_LA	k0, ejtag_debug_buffer_per_cpu
+	PTR_ADDU k0, k1
+	LONG_L	k1, 0(k0)
+#else
+	PTR_LA	k0, ejtag_debug_buffer
+	LONG_L	k1, 0(k0)
+#endif
+
+ejtag_return:
+	back_to_back_c0_hazard
+	MFC0	k0, CP0_DESAVE
+	.set	mips32
+	deret
+	.set	pop
+	END(ejtag_debug_handler)
+
+/*
+ * This buffer is reserved for the use of the EJTAG debug
+ * handler.
+ */
+	.data
+EXPORT(ejtag_debug_buffer)
+	.fill	LONGSIZE
+#ifdef CONFIG_SMP
+EXPORT(ejtag_debug_buffer_spinlock)
+	.fill	LONGSIZE
+EXPORT(ejtag_debug_buffer_per_cpu)
+	.fill	LONGSIZE * NR_CPUS
+#endif
+	.previous
+
+	__INIT
+
+/*
+ * NMI debug exception handler for MIPS reference boards.
+ * The NMI debug exception entry point is 0xbfc00000, which
+ * normally is in the boot PROM, so the boot PROM must do a
+ * unconditional jump to this vector.
+ */
+NESTED(except_vec_nmi, 0, sp)
+	j	nmi_handler
+#ifdef CONFIG_CPU_MICROMIPS
+	 nop
+#endif
+	END(except_vec_nmi)
+
+	__FINIT
+
+NESTED(nmi_handler, PT_SIZE, sp)
+	.cfi_signal_frame
+	.set	push
+	.set	noat
+	/*
+	 * Clear ERL - restore segment mapping
+	 * Clear BEV - required for page fault exception handler to work
+	 */
+	mfc0	k0, CP0_STATUS
+	ori	k0, k0, ST0_EXL
+	li	k1, ~(ST0_BEV | ST0_ERL)
+	and	k0, k0, k1
+	mtc0	k0, CP0_STATUS
+	_ehb
+	SAVE_ALL
+	move	a0, sp
+	jal	nmi_exception_handler
+	/* nmi_exception_handler never returns */
+	.set	pop
+	END(nmi_handler)
+
+	.macro	__build_clear_none
+	.endm
+
+	.macro	__build_clear_sti
+	TRACE_IRQS_ON
+	STI
+	.endm
+
+	.macro	__build_clear_cli
+	CLI
+	TRACE_IRQS_OFF
+	.endm
+
+	.macro	__build_clear_fpe
+	CLI
+	TRACE_IRQS_OFF
+	.set	push
+	/* gas fails to assemble cfc1 for some archs (octeon).*/ \
+	.set	mips1
+	SET_HARDFLOAT
+	cfc1	a1, fcr31
+	.set	pop
+	.endm
+
+	.macro	__build_clear_msa_fpe
+	CLI
+	TRACE_IRQS_OFF
+	_cfcmsa	a1, MSA_CSR
+	.endm
+
+	.macro	__build_clear_ade
+	MFC0	t0, CP0_BADVADDR
+	PTR_S	t0, PT_BVADDR(sp)
+	KMODE
+	.endm
+
+	.macro __build_clear_gsexc
+	.set	push
+	/*
+	 * We need to specify a selector to access the CP0.Diag1 (GSCause)
+	 * register. All GSExc-equipped processors have MIPS32.
+	 */
+	.set	mips32
+	mfc0	a1, CP0_DIAGNOSTIC1
+	.set	pop
+	TRACE_IRQS_ON
+	STI
+	.endm
+
+	.macro	__BUILD_silent exception
+	.endm
+
+	/* Gas tries to parse the ASM_PRINT argument as a string containing
+	   string escapes and emits bogus warnings if it believes to
+	   recognize an unknown escape code.  So make the arguments
+	   start with an n and gas will believe \n is ok ...  */
+	.macro	__BUILD_verbose nexception
+	LONG_L	a1, PT_EPC(sp)
+#ifdef CONFIG_32BIT
+	ASM_PRINT("Got \nexception at %08lx\012")
+#endif
+#ifdef CONFIG_64BIT
+	ASM_PRINT("Got \nexception at %016lx\012")
+#endif
+	.endm
+
+	.macro	__BUILD_count exception
+	LONG_L	t0,exception_count_\exception
+	LONG_ADDIU	t0, 1
+	LONG_S	t0,exception_count_\exception
+	.comm	exception_count\exception, 8, 8
+	.endm
+
+	.macro	__BUILD_HANDLER exception handler clear verbose ext
+	.align	5
+	NESTED(handle_\exception, PT_SIZE, sp)
+	.cfi_signal_frame
+	.set	noat
+	SAVE_ALL
+	FEXPORT(handle_\exception\ext)
+	__build_clear_\clear
+	.set	at
+	__BUILD_\verbose \exception
+	move	a0, sp
+	jal	do_\handler
+	j	ret_from_exception
+	END(handle_\exception)
+	.endm
+
+	.macro	BUILD_HANDLER exception handler clear verbose
+	__BUILD_HANDLER \exception \handler \clear \verbose _int
+	.endm
+
+	BUILD_HANDLER adel ade ade silent		/* #4  */
+	BUILD_HANDLER ades ade ade silent		/* #5  */
+	BUILD_HANDLER ibe be cli silent			/* #6  */
+	BUILD_HANDLER dbe be cli silent			/* #7  */
+	BUILD_HANDLER bp bp sti silent			/* #9  */
+	BUILD_HANDLER ri ri sti silent			/* #10 */
+	BUILD_HANDLER cpu cpu sti silent		/* #11 */
+	BUILD_HANDLER ov ov sti silent			/* #12 */
+	BUILD_HANDLER tr tr sti silent			/* #13 */
+	BUILD_HANDLER msa_fpe msa_fpe msa_fpe silent	/* #14 */
+#ifdef CONFIG_MIPS_FP_SUPPORT
+	BUILD_HANDLER fpe fpe fpe silent		/* #15 */
+#endif
+	BUILD_HANDLER ftlb ftlb none silent		/* #16 */
+	BUILD_HANDLER gsexc gsexc gsexc silent		/* #16 */
+	BUILD_HANDLER msa msa sti silent		/* #21 */
+	BUILD_HANDLER mdmx mdmx sti silent		/* #22 */
+#ifdef	CONFIG_HARDWARE_WATCHPOINTS
+	/*
+	 * For watch, interrupts will be enabled after the watch
+	 * registers are read.
+	 */
+	BUILD_HANDLER watch watch cli silent		/* #23 */
+#else
+	BUILD_HANDLER watch watch sti verbose		/* #23 */
+#endif
+	BUILD_HANDLER mcheck mcheck cli verbose		/* #24 */
+	BUILD_HANDLER mt mt sti silent			/* #25 */
+	BUILD_HANDLER dsp dsp sti silent		/* #26 */
+	BUILD_HANDLER reserved reserved sti verbose	/* others */
+
+	.align	5
+	LEAF(handle_ri_rdhwr_tlbp)
+	.set	push
+	.set	noat
+	.set	noreorder
+	/* check if TLB contains a entry for EPC */
+	MFC0	k1, CP0_ENTRYHI
+	andi	k1, MIPS_ENTRYHI_ASID | MIPS_ENTRYHI_ASIDX
+	MFC0	k0, CP0_EPC
+	PTR_SRL	k0, _PAGE_SHIFT + 1
+	PTR_SLL	k0, _PAGE_SHIFT + 1
+	or	k1, k0
+	MTC0	k1, CP0_ENTRYHI
+	mtc0_tlbw_hazard
+	tlbp
+	tlb_probe_hazard
+	mfc0	k1, CP0_INDEX
+	.set	pop
+	bltz	k1, handle_ri	/* slow path */
+	/* fall thru */
+	END(handle_ri_rdhwr_tlbp)
+
+	LEAF(handle_ri_rdhwr)
+	.set	push
+	.set	noat
+	.set	noreorder
+	/* MIPS32:    0x7c03e83b: rdhwr v1,$29 */
+	/* microMIPS: 0x007d6b3c: rdhwr v1,$29 */
+	MFC0	k1, CP0_EPC
+#if defined(CONFIG_CPU_MICROMIPS) || defined(CONFIG_CPU_MIPS32_R2) || defined(CONFIG_CPU_MIPS64_R2)
+	and	k0, k1, 1
+	beqz	k0, 1f
+	 xor	k1, k0
+	lhu	k0, (k1)
+	lhu	k1, 2(k1)
+	ins	k1, k0, 16, 16
+	lui	k0, 0x007d
+	b	docheck
+	 ori	k0, 0x6b3c
+1:
+	lui	k0, 0x7c03
+	lw	k1, (k1)
+	ori	k0, 0xe83b
+#else
+	andi	k0, k1, 1
+	bnez	k0, handle_ri
+	 lui	k0, 0x7c03
+	lw	k1, (k1)
+	ori	k0, 0xe83b
+#endif
+	.set	reorder
+docheck:
+	bne	k0, k1, handle_ri	/* if not ours */
+
+isrdhwr:
+	/* The insn is rdhwr.  No need to check CAUSE.BD here. */
+	get_saved_sp	/* k1 := current_thread_info */
+	.set	noreorder
+	MFC0	k0, CP0_EPC
+#if defined(CONFIG_CPU_R3000)
+	ori	k1, _THREAD_MASK
+	xori	k1, _THREAD_MASK
+	LONG_L	v1, TI_TP_VALUE(k1)
+	LONG_ADDIU	k0, 4
+	jr	k0
+	 rfe
+#else
+#ifndef CONFIG_CPU_DADDI_WORKAROUNDS
+	LONG_ADDIU	k0, 4		/* stall on $k0 */
+#else
+	.set	at=v1
+	LONG_ADDIU	k0, 4
+	.set	noat
+#endif
+	MTC0	k0, CP0_EPC
+	/* I hope three instructions between MTC0 and ERET are enough... */
+	ori	k1, _THREAD_MASK
+	xori	k1, _THREAD_MASK
+	LONG_L	v1, TI_TP_VALUE(k1)
+	.set	push
+	.set	arch=r4000
+	eret
+	.set	pop
+#endif
+	.set	pop
+	END(handle_ri_rdhwr)
+
+#ifdef CONFIG_CPU_R4X00_BUGS64
+/* A temporary overflow handler used by check_daddi(). */
+
+	__INIT
+
+	BUILD_HANDLER  daddi_ov daddi_ov none silent	/* #12 */
+#endif
diff --git a/arch/mips/kernel/gpio_txx9.c b/arch/mips/kernel/gpio_txx9.c
new file mode 100644
index 000000000..8c083612d
--- /dev/null
+++ b/arch/mips/kernel/gpio_txx9.c
@@ -0,0 +1,86 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * A gpio chip driver for TXx9 SoCs
+ *
+ * Copyright (C) 2008 Atsushi Nemoto <anemo@mba.ocn.ne.jp>
+ */
+
+#include <linux/init.h>
+#include <linux/spinlock.h>
+#include <linux/gpio/driver.h>
+#include <linux/errno.h>
+#include <linux/io.h>
+#include <asm/txx9pio.h>
+
+static DEFINE_SPINLOCK(txx9_gpio_lock);
+
+static struct txx9_pio_reg __iomem *txx9_pioptr;
+
+static int txx9_gpio_get(struct gpio_chip *chip, unsigned int offset)
+{
+	return !!(__raw_readl(&txx9_pioptr->din) & (1 << offset));
+}
+
+static void txx9_gpio_set_raw(unsigned int offset, int value)
+{
+	u32 val;
+	val = __raw_readl(&txx9_pioptr->dout);
+	if (value)
+		val |= 1 << offset;
+	else
+		val &= ~(1 << offset);
+	__raw_writel(val, &txx9_pioptr->dout);
+}
+
+static void txx9_gpio_set(struct gpio_chip *chip, unsigned int offset,
+			  int value)
+{
+	unsigned long flags;
+	spin_lock_irqsave(&txx9_gpio_lock, flags);
+	txx9_gpio_set_raw(offset, value);
+	mmiowb();
+	spin_unlock_irqrestore(&txx9_gpio_lock, flags);
+}
+
+static int txx9_gpio_dir_in(struct gpio_chip *chip, unsigned int offset)
+{
+	unsigned long flags;
+	spin_lock_irqsave(&txx9_gpio_lock, flags);
+	__raw_writel(__raw_readl(&txx9_pioptr->dir) & ~(1 << offset),
+		     &txx9_pioptr->dir);
+	mmiowb();
+	spin_unlock_irqrestore(&txx9_gpio_lock, flags);
+	return 0;
+}
+
+static int txx9_gpio_dir_out(struct gpio_chip *chip, unsigned int offset,
+			     int value)
+{
+	unsigned long flags;
+	spin_lock_irqsave(&txx9_gpio_lock, flags);
+	txx9_gpio_set_raw(offset, value);
+	__raw_writel(__raw_readl(&txx9_pioptr->dir) | (1 << offset),
+		     &txx9_pioptr->dir);
+	mmiowb();
+	spin_unlock_irqrestore(&txx9_gpio_lock, flags);
+	return 0;
+}
+
+static struct gpio_chip txx9_gpio_chip = {
+	.get = txx9_gpio_get,
+	.set = txx9_gpio_set,
+	.direction_input = txx9_gpio_dir_in,
+	.direction_output = txx9_gpio_dir_out,
+	.label = "TXx9",
+};
+
+int __init txx9_gpio_init(unsigned long baseaddr,
+			  unsigned int base, unsigned int num)
+{
+	txx9_pioptr = ioremap(baseaddr, sizeof(struct txx9_pio_reg));
+	if (!txx9_pioptr)
+		return -ENODEV;
+	txx9_gpio_chip.base = base;
+	txx9_gpio_chip.ngpio = num;
+	return gpiochip_add_data(&txx9_gpio_chip, NULL);
+}
diff --git a/arch/mips/kernel/head.S b/arch/mips/kernel/head.S
new file mode 100644
index 000000000..b825ed447
--- /dev/null
+++ b/arch/mips/kernel/head.S
@@ -0,0 +1,154 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994, 1995 Waldorf Electronics
+ * Written by Ralf Baechle and Andreas Busse
+ * Copyright (C) 1994 - 99, 2003, 06 Ralf Baechle
+ * Copyright (C) 1996 Paul M. Antoine
+ * Modified for DECStation and hence R3000 support by Paul M. Antoine
+ * Further modifications by David S. Miller and Harald Koerfgen
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ * Kevin Kissell, kevink@mips.com and Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 2000 MIPS Technologies, Inc.  All rights reserved.
+ */
+#include <linux/init.h>
+#include <linux/threads.h>
+
+#include <asm/addrspace.h>
+#include <asm/asm.h>
+#include <asm/asmmacro.h>
+#include <asm/irqflags.h>
+#include <asm/regdef.h>
+#include <asm/mipsregs.h>
+#include <asm/stackframe.h>
+
+#include <kernel-entry-init.h>
+
+	/*
+	 * For the moment disable interrupts, mark the kernel mode and
+	 * set ST0_KX so that the CPU does not spit fire when using
+	 * 64-bit addresses.  A full initialization of the CPU's status
+	 * register is done later in per_cpu_trap_init().
+	 */
+	.macro	setup_c0_status set clr
+	.set	push
+	mfc0	t0, CP0_STATUS
+	or	t0, ST0_KERNEL_CUMASK|\set|0x1f|\clr
+	xor	t0, 0x1f|\clr
+	mtc0	t0, CP0_STATUS
+	.set	noreorder
+	sll	zero,3				# ehb
+	.set	pop
+	.endm
+
+	.macro	setup_c0_status_pri
+#ifdef CONFIG_64BIT
+	setup_c0_status ST0_KX 0
+#else
+	setup_c0_status 0 0
+#endif
+	.endm
+
+	.macro	setup_c0_status_sec
+#ifdef CONFIG_64BIT
+	setup_c0_status ST0_KX ST0_BEV
+#else
+	setup_c0_status 0 ST0_BEV
+#endif
+	.endm
+
+#ifndef CONFIG_NO_EXCEPT_FILL
+	/*
+	 * Reserved space for exception handlers.
+	 * Necessary for machines which link their kernels at KSEG0.
+	 */
+	.fill	0x400
+#endif
+
+EXPORT(_stext)
+
+#ifdef CONFIG_BOOT_RAW
+	/*
+	 * Give us a fighting chance of running if execution beings at the
+	 * kernel load address.	 This is needed because this platform does
+	 * not have a ELF loader yet.
+	 */
+FEXPORT(__kernel_entry)
+	j	kernel_entry
+#endif /* CONFIG_BOOT_RAW */
+
+	__REF
+
+NESTED(kernel_entry, 16, sp)			# kernel entry point
+
+	kernel_entry_setup			# cpu specific setup
+
+	setup_c0_status_pri
+
+	/* We might not get launched at the address the kernel is linked to,
+	   so we jump there.  */
+	PTR_LA	t0, 0f
+	jr	t0
+0:
+
+	PTR_LA		t0, __bss_start		# clear .bss
+	LONG_S		zero, (t0)
+	PTR_LA		t1, __bss_stop - LONGSIZE
+1:
+	PTR_ADDIU	t0, LONGSIZE
+	LONG_S		zero, (t0)
+	bne		t0, t1, 1b
+
+	LONG_S		a0, fw_arg0		# firmware arguments
+	LONG_S		a1, fw_arg1
+	LONG_S		a2, fw_arg2
+	LONG_S		a3, fw_arg3
+
+	MTC0		zero, CP0_CONTEXT	# clear context register
+#ifdef CONFIG_64BIT
+	MTC0		zero, CP0_XCONTEXT
+#endif
+	PTR_LA		$28, init_thread_union
+	/* Set the SP after an empty pt_regs.  */
+	PTR_LI		sp, _THREAD_SIZE - 32 - PT_SIZE
+	PTR_ADDU	sp, $28
+	back_to_back_c0_hazard
+	set_saved_sp	sp, t0, t1
+	PTR_SUBU	sp, 4 * SZREG		# init stack pointer
+
+#ifdef CONFIG_RELOCATABLE
+	/* Copy kernel and apply the relocations */
+	jal		relocate_kernel
+
+	/* Repoint the sp into the new kernel image */
+	PTR_LI		sp, _THREAD_SIZE - 32 - PT_SIZE
+	PTR_ADDU	sp, $28
+	set_saved_sp	sp, t0, t1
+	PTR_SUBU	sp, 4 * SZREG		# init stack pointer
+
+	/*
+	 * relocate_kernel returns the entry point either
+	 * in the relocated kernel or the original if for
+	 * some reason relocation failed - jump there now
+	 * with instruction hazard barrier because of the
+	 * newly sync'd icache.
+	 */
+	jr.hb		v0
+#else  /* !CONFIG_RELOCATABLE */
+	j		start_kernel
+#endif /* !CONFIG_RELOCATABLE */
+	END(kernel_entry)
+
+#ifdef CONFIG_SMP
+/*
+ * SMP slave cpus entry point.	Board specific code for bootstrap calls this
+ * function after setting up the stack and gp registers.
+ */
+NESTED(smp_bootstrap, 16, sp)
+	smp_slave_setup
+	setup_c0_status_sec
+	j	start_secondary
+	END(smp_bootstrap)
+#endif /* CONFIG_SMP */
diff --git a/arch/mips/kernel/i8253.c b/arch/mips/kernel/i8253.c
new file mode 100644
index 000000000..ca21210e0
--- /dev/null
+++ b/arch/mips/kernel/i8253.c
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * i8253.c  8253/PIT functions
+ *
+ */
+#include <linux/clockchips.h>
+#include <linux/i8253.h>
+#include <linux/export.h>
+#include <linux/smp.h>
+#include <linux/irq.h>
+
+#include <asm/time.h>
+
+static irqreturn_t timer_interrupt(int irq, void *dev_id)
+{
+	i8253_clockevent.event_handler(&i8253_clockevent);
+
+	return IRQ_HANDLED;
+}
+
+void __init setup_pit_timer(void)
+{
+	unsigned long flags = IRQF_NOBALANCING | IRQF_TIMER;
+
+	clockevent_i8253_init(true);
+	if (request_irq(0, timer_interrupt, flags, "timer", NULL))
+		pr_err("Failed to request irq 0 (timer)\n");
+}
+
+static int __init init_pit_clocksource(void)
+{
+	if (num_possible_cpus() > 1 || /* PIT does not scale! */
+	    !clockevent_state_periodic(&i8253_clockevent))
+		return 0;
+
+	return clocksource_i8253_init();
+}
+arch_initcall(init_pit_clocksource);
diff --git a/arch/mips/kernel/idle.c b/arch/mips/kernel/idle.c
new file mode 100644
index 000000000..53adcc1b2
--- /dev/null
+++ b/arch/mips/kernel/idle.c
@@ -0,0 +1,261 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * MIPS idle loop and WAIT instruction support.
+ *
+ * Copyright (C) xxxx  the Anonymous
+ * Copyright (C) 1994 - 2006 Ralf Baechle
+ * Copyright (C) 2003, 2004  Maciej W. Rozycki
+ * Copyright (C) 2001, 2004, 2011, 2012	 MIPS Technologies, Inc.
+ */
+#include <linux/cpu.h>
+#include <linux/export.h>
+#include <linux/init.h>
+#include <linux/irqflags.h>
+#include <linux/printk.h>
+#include <linux/sched.h>
+#include <asm/cpu.h>
+#include <asm/cpu-info.h>
+#include <asm/cpu-type.h>
+#include <asm/idle.h>
+#include <asm/mipsregs.h>
+
+/*
+ * Not all of the MIPS CPUs have the "wait" instruction available. Moreover,
+ * the implementation of the "wait" feature differs between CPU families. This
+ * points to the function that implements CPU specific wait.
+ * The wait instruction stops the pipeline and reduces the power consumption of
+ * the CPU very much.
+ */
+void (*cpu_wait)(void);
+EXPORT_SYMBOL(cpu_wait);
+
+static void __cpuidle r3081_wait(void)
+{
+	unsigned long cfg = read_c0_conf();
+	write_c0_conf(cfg | R30XX_CONF_HALT);
+	raw_local_irq_enable();
+}
+
+void __cpuidle r4k_wait(void)
+{
+	raw_local_irq_enable();
+	__r4k_wait();
+}
+
+/*
+ * This variant is preferable as it allows testing need_resched and going to
+ * sleep depending on the outcome atomically.  Unfortunately the "It is
+ * implementation-dependent whether the pipeline restarts when a non-enabled
+ * interrupt is requested" restriction in the MIPS32/MIPS64 architecture makes
+ * using this version a gamble.
+ */
+void __cpuidle r4k_wait_irqoff(void)
+{
+	if (!need_resched())
+		__asm__(
+		"	.set	push		\n"
+		"	.set	arch=r4000	\n"
+		"	wait			\n"
+		"	.set	pop		\n");
+	raw_local_irq_enable();
+}
+
+/*
+ * The RM7000 variant has to handle erratum 38.	 The workaround is to not
+ * have any pending stores when the WAIT instruction is executed.
+ */
+static void __cpuidle rm7k_wait_irqoff(void)
+{
+	if (!need_resched())
+		__asm__(
+		"	.set	push					\n"
+		"	.set	arch=r4000				\n"
+		"	.set	noat					\n"
+		"	mfc0	$1, $12					\n"
+		"	sync						\n"
+		"	mtc0	$1, $12		# stalls until W stage	\n"
+		"	wait						\n"
+		"	mtc0	$1, $12		# stalls until W stage	\n"
+		"	.set	pop					\n");
+	raw_local_irq_enable();
+}
+
+/*
+ * Au1 'wait' is only useful when the 32kHz counter is used as timer,
+ * since coreclock (and the cp0 counter) stops upon executing it. Only an
+ * interrupt can wake it, so they must be enabled before entering idle modes.
+ */
+static void __cpuidle au1k_wait(void)
+{
+	unsigned long c0status = read_c0_status() | 1;	/* irqs on */
+
+	__asm__(
+	"	.set	push			\n"
+	"	.set	arch=r4000		\n"
+	"	cache	0x14, 0(%0)		\n"
+	"	cache	0x14, 32(%0)		\n"
+	"	sync				\n"
+	"	mtc0	%1, $12			\n" /* wr c0status */
+	"	wait				\n"
+	"	nop				\n"
+	"	nop				\n"
+	"	nop				\n"
+	"	nop				\n"
+	"	.set	pop			\n"
+	: : "r" (au1k_wait), "r" (c0status));
+}
+
+static int __initdata nowait;
+
+static int __init wait_disable(char *s)
+{
+	nowait = 1;
+
+	return 1;
+}
+
+__setup("nowait", wait_disable);
+
+void __init check_wait(void)
+{
+	struct cpuinfo_mips *c = &current_cpu_data;
+
+	if (nowait) {
+		printk("Wait instruction disabled.\n");
+		return;
+	}
+
+	/*
+	 * MIPSr6 specifies that masked interrupts should unblock an executing
+	 * wait instruction, and thus that it is safe for us to use
+	 * r4k_wait_irqoff. Yippee!
+	 */
+	if (cpu_has_mips_r6) {
+		cpu_wait = r4k_wait_irqoff;
+		return;
+	}
+
+	switch (current_cpu_type()) {
+	case CPU_R3081:
+	case CPU_R3081E:
+		cpu_wait = r3081_wait;
+		break;
+	case CPU_R4200:
+/*	case CPU_R4300: */
+	case CPU_R4600:
+	case CPU_R4640:
+	case CPU_R4650:
+	case CPU_R4700:
+	case CPU_R5000:
+	case CPU_R5500:
+	case CPU_NEVADA:
+	case CPU_4KC:
+	case CPU_4KEC:
+	case CPU_4KSC:
+	case CPU_5KC:
+	case CPU_5KE:
+	case CPU_25KF:
+	case CPU_PR4450:
+	case CPU_BMIPS3300:
+	case CPU_BMIPS4350:
+	case CPU_BMIPS4380:
+	case CPU_CAVIUM_OCTEON:
+	case CPU_CAVIUM_OCTEON_PLUS:
+	case CPU_CAVIUM_OCTEON2:
+	case CPU_CAVIUM_OCTEON3:
+	case CPU_XBURST:
+	case CPU_LOONGSON32:
+		cpu_wait = r4k_wait;
+		break;
+	case CPU_LOONGSON64:
+		if ((c->processor_id & (PRID_IMP_MASK | PRID_REV_MASK)) >=
+				(PRID_IMP_LOONGSON_64C | PRID_REV_LOONGSON3A_R2_0) ||
+				(c->processor_id & PRID_IMP_MASK) == PRID_IMP_LOONGSON_64R)
+			cpu_wait = r4k_wait;
+		break;
+
+	case CPU_BMIPS5000:
+		cpu_wait = r4k_wait_irqoff;
+		break;
+	case CPU_RM7000:
+		cpu_wait = rm7k_wait_irqoff;
+		break;
+
+	case CPU_PROAPTIV:
+	case CPU_P5600:
+		/*
+		 * Incoming Fast Debug Channel (FDC) data during a wait
+		 * instruction causes the wait never to resume, even if an
+		 * interrupt is received. Avoid using wait at all if FDC data is
+		 * likely to be received.
+		 */
+		if (IS_ENABLED(CONFIG_MIPS_EJTAG_FDC_TTY))
+			break;
+		fallthrough;
+	case CPU_M14KC:
+	case CPU_M14KEC:
+	case CPU_24K:
+	case CPU_34K:
+	case CPU_1004K:
+	case CPU_1074K:
+	case CPU_INTERAPTIV:
+	case CPU_M5150:
+	case CPU_QEMU_GENERIC:
+		cpu_wait = r4k_wait;
+		if (read_c0_config7() & MIPS_CONF7_WII)
+			cpu_wait = r4k_wait_irqoff;
+		break;
+
+	case CPU_74K:
+		cpu_wait = r4k_wait;
+		if ((c->processor_id & 0xff) >= PRID_REV_ENCODE_332(2, 1, 0))
+			cpu_wait = r4k_wait_irqoff;
+		break;
+
+	case CPU_TX49XX:
+		cpu_wait = r4k_wait_irqoff;
+		break;
+	case CPU_ALCHEMY:
+		cpu_wait = au1k_wait;
+		break;
+	case CPU_20KC:
+		/*
+		 * WAIT on Rev1.0 has E1, E2, E3 and E16.
+		 * WAIT on Rev2.0 and Rev3.0 has E16.
+		 * Rev3.1 WAIT is nop, why bother
+		 */
+		if ((c->processor_id & 0xff) <= 0x64)
+			break;
+
+		/*
+		 * Another rev is incrementing c0_count at a reduced clock
+		 * rate while in WAIT mode.  So we basically have the choice
+		 * between using the cp0 timer as clocksource or avoiding
+		 * the WAIT instruction.  Until more details are known,
+		 * disable the use of WAIT for 20Kc entirely.
+		   cpu_wait = r4k_wait;
+		 */
+		break;
+	default:
+		break;
+	}
+}
+
+void arch_cpu_idle(void)
+{
+	if (cpu_wait)
+		cpu_wait();
+	else
+		raw_local_irq_enable();
+}
+
+#ifdef CONFIG_CPU_IDLE
+
+int mips_cpuidle_wait_enter(struct cpuidle_device *dev,
+			    struct cpuidle_driver *drv, int index)
+{
+	arch_cpu_idle();
+	return index;
+}
+
+#endif
diff --git a/arch/mips/kernel/irq-gt641xx.c b/arch/mips/kernel/irq-gt641xx.c
new file mode 100644
index 000000000..93bcf5736
--- /dev/null
+++ b/arch/mips/kernel/irq-gt641xx.c
@@ -0,0 +1,118 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *  GT641xx IRQ routines.
+ *
+ *  Copyright (C) 2007	Yoichi Yuasa <yuasa@linux-mips.org>
+ */
+#include <linux/hardirq.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <linux/spinlock.h>
+#include <linux/types.h>
+
+#include <asm/gt64120.h>
+
+#define GT641XX_IRQ_TO_BIT(irq) (1U << (irq - GT641XX_IRQ_BASE))
+
+static DEFINE_RAW_SPINLOCK(gt641xx_irq_lock);
+
+static void ack_gt641xx_irq(struct irq_data *d)
+{
+	unsigned long flags;
+	u32 cause;
+
+	raw_spin_lock_irqsave(&gt641xx_irq_lock, flags);
+	cause = GT_READ(GT_INTRCAUSE_OFS);
+	cause &= ~GT641XX_IRQ_TO_BIT(d->irq);
+	GT_WRITE(GT_INTRCAUSE_OFS, cause);
+	raw_spin_unlock_irqrestore(&gt641xx_irq_lock, flags);
+}
+
+static void mask_gt641xx_irq(struct irq_data *d)
+{
+	unsigned long flags;
+	u32 mask;
+
+	raw_spin_lock_irqsave(&gt641xx_irq_lock, flags);
+	mask = GT_READ(GT_INTRMASK_OFS);
+	mask &= ~GT641XX_IRQ_TO_BIT(d->irq);
+	GT_WRITE(GT_INTRMASK_OFS, mask);
+	raw_spin_unlock_irqrestore(&gt641xx_irq_lock, flags);
+}
+
+static void mask_ack_gt641xx_irq(struct irq_data *d)
+{
+	unsigned long flags;
+	u32 cause, mask;
+
+	raw_spin_lock_irqsave(&gt641xx_irq_lock, flags);
+	mask = GT_READ(GT_INTRMASK_OFS);
+	mask &= ~GT641XX_IRQ_TO_BIT(d->irq);
+	GT_WRITE(GT_INTRMASK_OFS, mask);
+
+	cause = GT_READ(GT_INTRCAUSE_OFS);
+	cause &= ~GT641XX_IRQ_TO_BIT(d->irq);
+	GT_WRITE(GT_INTRCAUSE_OFS, cause);
+	raw_spin_unlock_irqrestore(&gt641xx_irq_lock, flags);
+}
+
+static void unmask_gt641xx_irq(struct irq_data *d)
+{
+	unsigned long flags;
+	u32 mask;
+
+	raw_spin_lock_irqsave(&gt641xx_irq_lock, flags);
+	mask = GT_READ(GT_INTRMASK_OFS);
+	mask |= GT641XX_IRQ_TO_BIT(d->irq);
+	GT_WRITE(GT_INTRMASK_OFS, mask);
+	raw_spin_unlock_irqrestore(&gt641xx_irq_lock, flags);
+}
+
+static struct irq_chip gt641xx_irq_chip = {
+	.name		= "GT641xx",
+	.irq_ack	= ack_gt641xx_irq,
+	.irq_mask	= mask_gt641xx_irq,
+	.irq_mask_ack	= mask_ack_gt641xx_irq,
+	.irq_unmask	= unmask_gt641xx_irq,
+};
+
+void gt641xx_irq_dispatch(void)
+{
+	u32 cause, mask;
+	int i;
+
+	cause = GT_READ(GT_INTRCAUSE_OFS);
+	mask = GT_READ(GT_INTRMASK_OFS);
+	cause &= mask;
+
+	/*
+	 * bit0 : logical or of all the interrupt bits.
+	 * bit30: logical or of bits[29:26,20:1].
+	 * bit31: logical or of bits[25:1].
+	 */
+	for (i = 1; i < 30; i++) {
+		if (cause & (1U << i)) {
+			do_IRQ(GT641XX_IRQ_BASE + i);
+			return;
+		}
+	}
+
+	atomic_inc(&irq_err_count);
+}
+
+void __init gt641xx_irq_init(void)
+{
+	int i;
+
+	GT_WRITE(GT_INTRMASK_OFS, 0);
+	GT_WRITE(GT_INTRCAUSE_OFS, 0);
+
+	/*
+	 * bit0 : logical or of all the interrupt bits.
+	 * bit30: logical or of bits[29:26,20:1].
+	 * bit31: logical or of bits[25:1].
+	 */
+	for (i = 1; i < 30; i++)
+		irq_set_chip_and_handler(GT641XX_IRQ_BASE + i,
+					 &gt641xx_irq_chip, handle_level_irq);
+}
diff --git a/arch/mips/kernel/irq-msc01.c b/arch/mips/kernel/irq-msc01.c
new file mode 100644
index 000000000..ab511b64a
--- /dev/null
+++ b/arch/mips/kernel/irq-msc01.c
@@ -0,0 +1,156 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *
+ * Copyright (c) 2004 MIPS Inc
+ * Author: chris@mips.com
+ *
+ * Copyright (C) 2004, 06 Ralf Baechle <ralf@linux-mips.org>
+ */
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/kernel_stat.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/msc01_ic.h>
+#include <asm/traps.h>
+
+static unsigned long _icctrl_msc;
+#define MSC01_IC_REG_BASE	_icctrl_msc
+
+#define MSCIC_WRITE(reg, data)	do { *(volatile u32 *)(reg) = data; } while (0)
+#define MSCIC_READ(reg, data)	do { data = *(volatile u32 *)(reg); } while (0)
+
+static unsigned int irq_base;
+
+/* mask off an interrupt */
+static inline void mask_msc_irq(struct irq_data *d)
+{
+	unsigned int irq = d->irq;
+
+	if (irq < (irq_base + 32))
+		MSCIC_WRITE(MSC01_IC_DISL, 1<<(irq - irq_base));
+	else
+		MSCIC_WRITE(MSC01_IC_DISH, 1<<(irq - irq_base - 32));
+}
+
+/* unmask an interrupt */
+static inline void unmask_msc_irq(struct irq_data *d)
+{
+	unsigned int irq = d->irq;
+
+	if (irq < (irq_base + 32))
+		MSCIC_WRITE(MSC01_IC_ENAL, 1<<(irq - irq_base));
+	else
+		MSCIC_WRITE(MSC01_IC_ENAH, 1<<(irq - irq_base - 32));
+}
+
+/*
+ * Masks and ACKs an IRQ
+ */
+static void level_mask_and_ack_msc_irq(struct irq_data *d)
+{
+	mask_msc_irq(d);
+	if (!cpu_has_veic)
+		MSCIC_WRITE(MSC01_IC_EOI, 0);
+}
+
+/*
+ * Masks and ACKs an IRQ
+ */
+static void edge_mask_and_ack_msc_irq(struct irq_data *d)
+{
+	unsigned int irq = d->irq;
+
+	mask_msc_irq(d);
+	if (!cpu_has_veic)
+		MSCIC_WRITE(MSC01_IC_EOI, 0);
+	else {
+		u32 r;
+		MSCIC_READ(MSC01_IC_SUP+irq*8, r);
+		MSCIC_WRITE(MSC01_IC_SUP+irq*8, r | ~MSC01_IC_SUP_EDGE_BIT);
+		MSCIC_WRITE(MSC01_IC_SUP+irq*8, r);
+	}
+}
+
+/*
+ * Interrupt handler for interrupts coming from SOC-it.
+ */
+void ll_msc_irq(void)
+{
+	unsigned int irq;
+
+	/* read the interrupt vector register */
+	MSCIC_READ(MSC01_IC_VEC, irq);
+	if (irq < 64)
+		do_IRQ(irq + irq_base);
+	else {
+		/* Ignore spurious interrupt */
+	}
+}
+
+static void msc_bind_eic_interrupt(int irq, int set)
+{
+	MSCIC_WRITE(MSC01_IC_RAMW,
+		    (irq<<MSC01_IC_RAMW_ADDR_SHF) | (set<<MSC01_IC_RAMW_DATA_SHF));
+}
+
+static struct irq_chip msc_levelirq_type = {
+	.name = "SOC-it-Level",
+	.irq_ack = level_mask_and_ack_msc_irq,
+	.irq_mask = mask_msc_irq,
+	.irq_mask_ack = level_mask_and_ack_msc_irq,
+	.irq_unmask = unmask_msc_irq,
+	.irq_eoi = unmask_msc_irq,
+};
+
+static struct irq_chip msc_edgeirq_type = {
+	.name = "SOC-it-Edge",
+	.irq_ack = edge_mask_and_ack_msc_irq,
+	.irq_mask = mask_msc_irq,
+	.irq_mask_ack = edge_mask_and_ack_msc_irq,
+	.irq_unmask = unmask_msc_irq,
+	.irq_eoi = unmask_msc_irq,
+};
+
+
+void __init init_msc_irqs(unsigned long icubase, unsigned int irqbase, msc_irqmap_t *imp, int nirq)
+{
+	_icctrl_msc = (unsigned long) ioremap(icubase, 0x40000);
+
+	/* Reset interrupt controller - initialises all registers to 0 */
+	MSCIC_WRITE(MSC01_IC_RST, MSC01_IC_RST_RST_BIT);
+
+	board_bind_eic_interrupt = &msc_bind_eic_interrupt;
+
+	for (; nirq > 0; nirq--, imp++) {
+		int n = imp->im_irq;
+
+		switch (imp->im_type) {
+		case MSC01_IRQ_EDGE:
+			irq_set_chip_and_handler_name(irqbase + n,
+						      &msc_edgeirq_type,
+						      handle_edge_irq,
+						      "edge");
+			if (cpu_has_veic)
+				MSCIC_WRITE(MSC01_IC_SUP+n*8, MSC01_IC_SUP_EDGE_BIT);
+			else
+				MSCIC_WRITE(MSC01_IC_SUP+n*8, MSC01_IC_SUP_EDGE_BIT | imp->im_lvl);
+			break;
+		case MSC01_IRQ_LEVEL:
+			irq_set_chip_and_handler_name(irqbase + n,
+						      &msc_levelirq_type,
+						      handle_level_irq,
+						      "level");
+			if (cpu_has_veic)
+				MSCIC_WRITE(MSC01_IC_SUP+n*8, 0);
+			else
+				MSCIC_WRITE(MSC01_IC_SUP+n*8, imp->im_lvl);
+		}
+	}
+
+	irq_base = irqbase;
+
+	MSCIC_WRITE(MSC01_IC_GENA, MSC01_IC_GENA_GENA_BIT);	/* Enable interrupt generation */
+
+}
diff --git a/arch/mips/kernel/irq.c b/arch/mips/kernel/irq.c
new file mode 100644
index 000000000..5e11582fe
--- /dev/null
+++ b/arch/mips/kernel/irq.c
@@ -0,0 +1,119 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Code to handle x86 style IRQs plus some generic interrupt stuff.
+ *
+ * Copyright (C) 1992 Linus Torvalds
+ * Copyright (C) 1994 - 2000 Ralf Baechle
+ */
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel_stat.h>
+#include <linux/proc_fs.h>
+#include <linux/mm.h>
+#include <linux/random.h>
+#include <linux/sched.h>
+#include <linux/seq_file.h>
+#include <linux/kallsyms.h>
+#include <linux/kgdb.h>
+#include <linux/ftrace.h>
+#include <linux/irqdomain.h>
+
+#include <linux/atomic.h>
+#include <linux/uaccess.h>
+
+void *irq_stack[NR_CPUS];
+
+/*
+ * 'what should we do if we get a hw irq event on an illegal vector'.
+ * each architecture has to answer this themselves.
+ */
+void ack_bad_irq(unsigned int irq)
+{
+	printk("unexpected IRQ # %d\n", irq);
+}
+
+atomic_t irq_err_count;
+
+int arch_show_interrupts(struct seq_file *p, int prec)
+{
+	seq_printf(p, "%*s: %10u\n", prec, "ERR", atomic_read(&irq_err_count));
+	return 0;
+}
+
+asmlinkage void spurious_interrupt(void)
+{
+	atomic_inc(&irq_err_count);
+}
+
+void __init init_IRQ(void)
+{
+	int i;
+	unsigned int order = get_order(IRQ_STACK_SIZE);
+
+	for (i = 0; i < NR_IRQS; i++)
+		irq_set_noprobe(i);
+
+	if (cpu_has_veic)
+		clear_c0_status(ST0_IM);
+
+	arch_init_irq();
+
+	for_each_possible_cpu(i) {
+		void *s = (void *)__get_free_pages(GFP_KERNEL, order);
+
+		irq_stack[i] = s;
+		pr_debug("CPU%d IRQ stack at 0x%p - 0x%p\n", i,
+			irq_stack[i], irq_stack[i] + IRQ_STACK_SIZE);
+	}
+}
+
+#ifdef CONFIG_DEBUG_STACKOVERFLOW
+static inline void check_stack_overflow(void)
+{
+	unsigned long sp;
+
+	__asm__ __volatile__("move %0, $sp" : "=r" (sp));
+	sp &= THREAD_MASK;
+
+	/*
+	 * Check for stack overflow: is there less than STACK_WARN free?
+	 * STACK_WARN is defined as 1/8 of THREAD_SIZE by default.
+	 */
+	if (unlikely(sp < (sizeof(struct thread_info) + STACK_WARN))) {
+		printk("do_IRQ: stack overflow: %ld\n",
+		       sp - sizeof(struct thread_info));
+		dump_stack();
+	}
+}
+#else
+static inline void check_stack_overflow(void) {}
+#endif
+
+
+/*
+ * do_IRQ handles all normal device IRQ's (the special
+ * SMP cross-CPU interrupts have their own specific
+ * handlers).
+ */
+void __irq_entry do_IRQ(unsigned int irq)
+{
+	irq_enter();
+	check_stack_overflow();
+	generic_handle_irq(irq);
+	irq_exit();
+}
+
+#ifdef CONFIG_IRQ_DOMAIN
+void __irq_entry do_domain_IRQ(struct irq_domain *domain, unsigned int hwirq)
+{
+	irq_enter();
+	check_stack_overflow();
+	generic_handle_domain_irq(domain, hwirq);
+	irq_exit();
+}
+#endif
diff --git a/arch/mips/kernel/irq_txx9.c b/arch/mips/kernel/irq_txx9.c
new file mode 100644
index 000000000..af3ef4c9f
--- /dev/null
+++ b/arch/mips/kernel/irq_txx9.c
@@ -0,0 +1,178 @@
+/*
+ * Based on linux/arch/mips/jmr3927/rbhma3100/irq.c,
+ *	    linux/arch/mips/tx4927/common/tx4927_irq.c,
+ *	    linux/arch/mips/tx4938/common/irq.c
+ *
+ * Copyright 2001, 2003-2005 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc.
+ *	   ahennessy@mvista.com
+ *	   source@mvista.com
+ * Copyright (C) 2000-2001 Toshiba Corporation
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/types.h>
+#include <linux/irq.h>
+#include <asm/txx9irq.h>
+
+struct txx9_irc_reg {
+	u32 cer;
+	u32 cr[2];
+	u32 unused0;
+	u32 ilr[8];
+	u32 unused1[4];
+	u32 imr;
+	u32 unused2[7];
+	u32 scr;
+	u32 unused3[7];
+	u32 ssr;
+	u32 unused4[7];
+	u32 csr;
+};
+
+/* IRCER : Int. Control Enable */
+#define TXx9_IRCER_ICE	0x00000001
+
+/* IRCR : Int. Control */
+#define TXx9_IRCR_LOW	0x00000000
+#define TXx9_IRCR_HIGH	0x00000001
+#define TXx9_IRCR_DOWN	0x00000002
+#define TXx9_IRCR_UP	0x00000003
+#define TXx9_IRCR_EDGE(cr)	((cr) & 0x00000002)
+
+/* IRSCR : Int. Status Control */
+#define TXx9_IRSCR_EIClrE	0x00000100
+#define TXx9_IRSCR_EIClr_MASK	0x0000000f
+
+/* IRCSR : Int. Current Status */
+#define TXx9_IRCSR_IF	0x00010000
+#define TXx9_IRCSR_ILV_MASK	0x00000700
+#define TXx9_IRCSR_IVL_MASK	0x0000001f
+
+#define irc_dlevel	0
+#define irc_elevel	1
+
+static struct txx9_irc_reg __iomem *txx9_ircptr __read_mostly;
+
+static struct {
+	unsigned char level;
+	unsigned char mode;
+} txx9irq[TXx9_MAX_IR] __read_mostly;
+
+static void txx9_irq_unmask(struct irq_data *d)
+{
+	unsigned int irq_nr = d->irq - TXX9_IRQ_BASE;
+	u32 __iomem *ilrp = &txx9_ircptr->ilr[(irq_nr % 16 ) / 2];
+	int ofs = irq_nr / 16 * 16 + (irq_nr & 1) * 8;
+
+	__raw_writel((__raw_readl(ilrp) & ~(0xff << ofs))
+		     | (txx9irq[irq_nr].level << ofs),
+		     ilrp);
+}
+
+static inline void txx9_irq_mask(struct irq_data *d)
+{
+	unsigned int irq_nr = d->irq - TXX9_IRQ_BASE;
+	u32 __iomem *ilrp = &txx9_ircptr->ilr[(irq_nr % 16) / 2];
+	int ofs = irq_nr / 16 * 16 + (irq_nr & 1) * 8;
+
+	__raw_writel((__raw_readl(ilrp) & ~(0xff << ofs))
+		     | (irc_dlevel << ofs),
+		     ilrp);
+	mmiowb();
+}
+
+static void txx9_irq_mask_ack(struct irq_data *d)
+{
+	unsigned int irq_nr = d->irq - TXX9_IRQ_BASE;
+
+	txx9_irq_mask(d);
+	/* clear edge detection */
+	if (unlikely(TXx9_IRCR_EDGE(txx9irq[irq_nr].mode)))
+		__raw_writel(TXx9_IRSCR_EIClrE | irq_nr, &txx9_ircptr->scr);
+}
+
+static int txx9_irq_set_type(struct irq_data *d, unsigned int flow_type)
+{
+	unsigned int irq_nr = d->irq - TXX9_IRQ_BASE;
+	u32 cr;
+	u32 __iomem *crp;
+	int ofs;
+	int mode;
+
+	if (flow_type & IRQF_TRIGGER_PROBE)
+		return 0;
+	switch (flow_type & IRQF_TRIGGER_MASK) {
+	case IRQF_TRIGGER_RISING:	mode = TXx9_IRCR_UP;	break;
+	case IRQF_TRIGGER_FALLING:	mode = TXx9_IRCR_DOWN;	break;
+	case IRQF_TRIGGER_HIGH: mode = TXx9_IRCR_HIGH;	break;
+	case IRQF_TRIGGER_LOW:	mode = TXx9_IRCR_LOW;	break;
+	default:
+		return -EINVAL;
+	}
+	crp = &txx9_ircptr->cr[(unsigned int)irq_nr / 8];
+	cr = __raw_readl(crp);
+	ofs = (irq_nr & (8 - 1)) * 2;
+	cr &= ~(0x3 << ofs);
+	cr |= (mode & 0x3) << ofs;
+	__raw_writel(cr, crp);
+	txx9irq[irq_nr].mode = mode;
+	return 0;
+}
+
+static struct irq_chip txx9_irq_chip = {
+	.name		= "TXX9",
+	.irq_ack	= txx9_irq_mask_ack,
+	.irq_mask	= txx9_irq_mask,
+	.irq_mask_ack	= txx9_irq_mask_ack,
+	.irq_unmask	= txx9_irq_unmask,
+	.irq_set_type	= txx9_irq_set_type,
+};
+
+void __init txx9_irq_init(unsigned long baseaddr)
+{
+	int i;
+
+	txx9_ircptr = ioremap(baseaddr, sizeof(struct txx9_irc_reg));
+	for (i = 0; i < TXx9_MAX_IR; i++) {
+		txx9irq[i].level = 4; /* middle level */
+		txx9irq[i].mode = TXx9_IRCR_LOW;
+		irq_set_chip_and_handler(TXX9_IRQ_BASE + i, &txx9_irq_chip,
+					 handle_level_irq);
+	}
+
+	/* mask all IRC interrupts */
+	__raw_writel(0, &txx9_ircptr->imr);
+	for (i = 0; i < 8; i++)
+		__raw_writel(0, &txx9_ircptr->ilr[i]);
+	/* setup IRC interrupt mode (Low Active) */
+	for (i = 0; i < 2; i++)
+		__raw_writel(0, &txx9_ircptr->cr[i]);
+	/* enable interrupt control */
+	__raw_writel(TXx9_IRCER_ICE, &txx9_ircptr->cer);
+	__raw_writel(irc_elevel, &txx9_ircptr->imr);
+}
+
+int __init txx9_irq_set_pri(int irc_irq, int new_pri)
+{
+	int old_pri;
+
+	if ((unsigned int)irc_irq >= TXx9_MAX_IR)
+		return 0;
+	old_pri = txx9irq[irc_irq].level;
+	txx9irq[irc_irq].level = new_pri;
+	return old_pri;
+}
+
+int txx9_irq(void)
+{
+	u32 csr = __raw_readl(&txx9_ircptr->csr);
+
+	if (likely(!(csr & TXx9_IRCSR_IF)))
+		return TXX9_IRQ_BASE + (csr & (TXx9_MAX_IR - 1));
+	return -1;
+}
diff --git a/arch/mips/kernel/jump_label.c b/arch/mips/kernel/jump_label.c
new file mode 100644
index 000000000..f7978d50a
--- /dev/null
+++ b/arch/mips/kernel/jump_label.c
@@ -0,0 +1,109 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (c) 2010 Cavium Networks, Inc.
+ */
+
+#include <linux/jump_label.h>
+#include <linux/kernel.h>
+#include <linux/memory.h>
+#include <linux/mutex.h>
+#include <linux/types.h>
+#include <linux/cpu.h>
+
+#include <asm/cacheflush.h>
+#include <asm/inst.h>
+
+/*
+ * Define parameters for the standard MIPS and the microMIPS jump
+ * instruction encoding respectively:
+ *
+ * - the ISA bit of the target, either 0 or 1 respectively,
+ *
+ * - the amount the jump target address is shifted right to fit in the
+ *   immediate field of the machine instruction, either 2 or 1,
+ *
+ * - the mask determining the size of the jump region relative to the
+ *   delay-slot instruction, either 256MB or 128MB,
+ *
+ * - the jump target alignment, either 4 or 2 bytes.
+ */
+#define J_ISA_BIT	IS_ENABLED(CONFIG_CPU_MICROMIPS)
+#define J_RANGE_SHIFT	(2 - J_ISA_BIT)
+#define J_RANGE_MASK	((1ul << (26 + J_RANGE_SHIFT)) - 1)
+#define J_ALIGN_MASK	((1ul << J_RANGE_SHIFT) - 1)
+
+void arch_jump_label_transform(struct jump_entry *e,
+			       enum jump_label_type type)
+{
+	union mips_instruction *insn_p;
+	union mips_instruction insn;
+	long offset;
+
+	insn_p = (union mips_instruction *)msk_isa16_mode(e->code);
+
+	/* Target must have the right alignment and ISA must be preserved. */
+	BUG_ON((e->target & J_ALIGN_MASK) != J_ISA_BIT);
+
+	if (type == JUMP_LABEL_JMP) {
+		if (!IS_ENABLED(CONFIG_CPU_MICROMIPS) && MIPS_ISA_REV >= 6) {
+			offset = e->target - ((unsigned long)insn_p + 4);
+			offset >>= 2;
+
+			/*
+			 * The branch offset must fit in the instruction's 26
+			 * bit field.
+			 */
+			WARN_ON((offset >= (long)BIT(25)) ||
+				(offset < -(long)BIT(25)));
+
+			insn.j_format.opcode = bc6_op;
+			insn.j_format.target = offset;
+		} else {
+			/*
+			 * Jump only works within an aligned region its delay
+			 * slot is in.
+			 */
+			WARN_ON((e->target & ~J_RANGE_MASK) !=
+				((e->code + 4) & ~J_RANGE_MASK));
+
+			insn.j_format.opcode = J_ISA_BIT ? mm_j32_op : j_op;
+			insn.j_format.target = e->target >> J_RANGE_SHIFT;
+		}
+	} else {
+		insn.word = 0; /* nop */
+	}
+
+	mutex_lock(&text_mutex);
+	if (IS_ENABLED(CONFIG_CPU_MICROMIPS)) {
+		insn_p->halfword[0] = insn.word >> 16;
+		insn_p->halfword[1] = insn.word;
+	} else
+		*insn_p = insn;
+
+	flush_icache_range((unsigned long)insn_p,
+			   (unsigned long)insn_p + sizeof(*insn_p));
+
+	mutex_unlock(&text_mutex);
+}
+
+#ifdef CONFIG_MODULES
+void jump_label_apply_nops(struct module *mod)
+{
+	struct jump_entry *iter_start = mod->jump_entries;
+	struct jump_entry *iter_stop = iter_start + mod->num_jump_entries;
+	struct jump_entry *iter;
+
+	/* if the module doesn't have jump label entries, just return */
+	if (iter_start == iter_stop)
+		return;
+
+	for (iter = iter_start; iter < iter_stop; iter++) {
+		/* Only write NOPs for arch_branch_static(). */
+		if (jump_label_init_type(iter) == JUMP_LABEL_NOP)
+			arch_jump_label_transform(iter, JUMP_LABEL_NOP);
+	}
+}
+#endif
diff --git a/arch/mips/kernel/kgdb.c b/arch/mips/kernel/kgdb.c
new file mode 100644
index 000000000..09a2d7bb9
--- /dev/null
+++ b/arch/mips/kernel/kgdb.c
@@ -0,0 +1,394 @@
+/*
+ *  Originally written by Glenn Engel, Lake Stevens Instrument Division
+ *
+ *  Contributed by HP Systems
+ *
+ *  Modified for Linux/MIPS (and MIPS in general) by Andreas Busse
+ *  Send complaints, suggestions etc. to <andy@waldorf-gmbh.de>
+ *
+ *  Copyright (C) 1995 Andreas Busse
+ *
+ *  Copyright (C) 2003 MontaVista Software Inc.
+ *  Author: Jun Sun, jsun@mvista.com or jsun@junsun.net
+ *
+ *  Copyright (C) 2004-2005 MontaVista Software Inc.
+ *  Author: Manish Lachwani, mlachwani@mvista.com or manish@koffee-break.com
+ *
+ *  Copyright (C) 2007-2008 Wind River Systems, Inc.
+ *  Author/Maintainer: Jason Wessel, jason.wessel@windriver.com
+ *
+ *  This file is licensed under the terms of the GNU General Public License
+ *  version 2. This program is licensed "as is" without any warranty of any
+ *  kind, whether express or implied.
+ */
+
+#include <linux/ptrace.h>		/* for linux pt_regs struct */
+#include <linux/kgdb.h>
+#include <linux/kdebug.h>
+#include <linux/sched.h>
+#include <linux/smp.h>
+#include <asm/inst.h>
+#include <asm/fpu.h>
+#include <asm/cacheflush.h>
+#include <asm/processor.h>
+#include <asm/sigcontext.h>
+#include <asm/irq_regs.h>
+
+static struct hard_trap_info {
+	unsigned char tt;	/* Trap type code for MIPS R3xxx and R4xxx */
+	unsigned char signo;	/* Signal that we map this trap into */
+} hard_trap_info[] = {
+	{ 6, SIGBUS },		/* instruction bus error */
+	{ 7, SIGBUS },		/* data bus error */
+	{ 9, SIGTRAP },		/* break */
+/*	{ 11, SIGILL }, */	/* CPU unusable */
+	{ 12, SIGFPE },		/* overflow */
+	{ 13, SIGTRAP },	/* trap */
+	{ 14, SIGSEGV },	/* virtual instruction cache coherency */
+	{ 15, SIGFPE },		/* floating point exception */
+	{ 23, SIGSEGV },	/* watch */
+	{ 31, SIGSEGV },	/* virtual data cache coherency */
+	{ 0, 0}			/* Must be last */
+};
+
+struct dbg_reg_def_t dbg_reg_def[DBG_MAX_REG_NUM] =
+{
+	{ "zero", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[0]) },
+	{ "at", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[1]) },
+	{ "v0", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[2]) },
+	{ "v1", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[3]) },
+	{ "a0", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[4]) },
+	{ "a1", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[5]) },
+	{ "a2", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[6]) },
+	{ "a3", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[7]) },
+	{ "t0", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[8]) },
+	{ "t1", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[9]) },
+	{ "t2", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[10]) },
+	{ "t3", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[11]) },
+	{ "t4", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[12]) },
+	{ "t5", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[13]) },
+	{ "t6", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[14]) },
+	{ "t7", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[15]) },
+	{ "s0", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[16]) },
+	{ "s1", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[17]) },
+	{ "s2", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[18]) },
+	{ "s3", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[19]) },
+	{ "s4", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[20]) },
+	{ "s5", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[21]) },
+	{ "s6", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[22]) },
+	{ "s7", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[23]) },
+	{ "t8", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[24]) },
+	{ "t9", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[25]) },
+	{ "k0", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[26]) },
+	{ "k1", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[27]) },
+	{ "gp", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[28]) },
+	{ "sp", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[29]) },
+	{ "s8", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[30]) },
+	{ "ra", GDB_SIZEOF_REG, offsetof(struct pt_regs, regs[31]) },
+	{ "sr", GDB_SIZEOF_REG, offsetof(struct pt_regs, cp0_status) },
+	{ "lo", GDB_SIZEOF_REG, offsetof(struct pt_regs, lo) },
+	{ "hi", GDB_SIZEOF_REG, offsetof(struct pt_regs, hi) },
+	{ "bad", GDB_SIZEOF_REG, offsetof(struct pt_regs, cp0_badvaddr) },
+	{ "cause", GDB_SIZEOF_REG, offsetof(struct pt_regs, cp0_cause) },
+	{ "pc", GDB_SIZEOF_REG, offsetof(struct pt_regs, cp0_epc) },
+	{ "f0", GDB_SIZEOF_REG, 0 },
+	{ "f1", GDB_SIZEOF_REG, 1 },
+	{ "f2", GDB_SIZEOF_REG, 2 },
+	{ "f3", GDB_SIZEOF_REG, 3 },
+	{ "f4", GDB_SIZEOF_REG, 4 },
+	{ "f5", GDB_SIZEOF_REG, 5 },
+	{ "f6", GDB_SIZEOF_REG, 6 },
+	{ "f7", GDB_SIZEOF_REG, 7 },
+	{ "f8", GDB_SIZEOF_REG, 8 },
+	{ "f9", GDB_SIZEOF_REG, 9 },
+	{ "f10", GDB_SIZEOF_REG, 10 },
+	{ "f11", GDB_SIZEOF_REG, 11 },
+	{ "f12", GDB_SIZEOF_REG, 12 },
+	{ "f13", GDB_SIZEOF_REG, 13 },
+	{ "f14", GDB_SIZEOF_REG, 14 },
+	{ "f15", GDB_SIZEOF_REG, 15 },
+	{ "f16", GDB_SIZEOF_REG, 16 },
+	{ "f17", GDB_SIZEOF_REG, 17 },
+	{ "f18", GDB_SIZEOF_REG, 18 },
+	{ "f19", GDB_SIZEOF_REG, 19 },
+	{ "f20", GDB_SIZEOF_REG, 20 },
+	{ "f21", GDB_SIZEOF_REG, 21 },
+	{ "f22", GDB_SIZEOF_REG, 22 },
+	{ "f23", GDB_SIZEOF_REG, 23 },
+	{ "f24", GDB_SIZEOF_REG, 24 },
+	{ "f25", GDB_SIZEOF_REG, 25 },
+	{ "f26", GDB_SIZEOF_REG, 26 },
+	{ "f27", GDB_SIZEOF_REG, 27 },
+	{ "f28", GDB_SIZEOF_REG, 28 },
+	{ "f29", GDB_SIZEOF_REG, 29 },
+	{ "f30", GDB_SIZEOF_REG, 30 },
+	{ "f31", GDB_SIZEOF_REG, 31 },
+	{ "fsr", GDB_SIZEOF_REG, 0 },
+	{ "fir", GDB_SIZEOF_REG, 0 },
+};
+
+int dbg_set_reg(int regno, void *mem, struct pt_regs *regs)
+{
+	int fp_reg;
+
+	if (regno < 0 || regno >= DBG_MAX_REG_NUM)
+		return -EINVAL;
+
+	if (dbg_reg_def[regno].offset != -1 && regno < 38) {
+		memcpy((void *)regs + dbg_reg_def[regno].offset, mem,
+		       dbg_reg_def[regno].size);
+	} else if (current && dbg_reg_def[regno].offset != -1 && regno < 72) {
+		/* FP registers 38 -> 69 */
+		if (!(regs->cp0_status & ST0_CU1))
+			return 0;
+		if (regno == 70) {
+			/* Process the fcr31/fsr (register 70) */
+			memcpy((void *)&current->thread.fpu.fcr31, mem,
+			       dbg_reg_def[regno].size);
+			goto out_save;
+		} else if (regno == 71) {
+			/* Ignore the fir (register 71) */
+			goto out_save;
+		}
+		fp_reg = dbg_reg_def[regno].offset;
+		memcpy((void *)&current->thread.fpu.fpr[fp_reg], mem,
+		       dbg_reg_def[regno].size);
+out_save:
+		restore_fp(current);
+	}
+
+	return 0;
+}
+
+char *dbg_get_reg(int regno, void *mem, struct pt_regs *regs)
+{
+	int fp_reg;
+
+	if (regno >= DBG_MAX_REG_NUM || regno < 0)
+		return NULL;
+
+	if (dbg_reg_def[regno].offset != -1 && regno < 38) {
+		/* First 38 registers */
+		memcpy(mem, (void *)regs + dbg_reg_def[regno].offset,
+		       dbg_reg_def[regno].size);
+	} else if (current && dbg_reg_def[regno].offset != -1 && regno < 72) {
+		/* FP registers 38 -> 69 */
+		if (!(regs->cp0_status & ST0_CU1))
+			goto out;
+		save_fp(current);
+		if (regno == 70) {
+			/* Process the fcr31/fsr (register 70) */
+			memcpy(mem, (void *)&current->thread.fpu.fcr31,
+			       dbg_reg_def[regno].size);
+			goto out;
+		} else if (regno == 71) {
+			/* Ignore the fir (register 71) */
+			memset(mem, 0, dbg_reg_def[regno].size);
+			goto out;
+		}
+		fp_reg = dbg_reg_def[regno].offset;
+		memcpy(mem, (void *)&current->thread.fpu.fpr[fp_reg],
+		       dbg_reg_def[regno].size);
+	}
+
+out:
+	return dbg_reg_def[regno].name;
+
+}
+
+void arch_kgdb_breakpoint(void)
+{
+	__asm__ __volatile__(
+		".globl breakinst\n\t"
+		".set\tnoreorder\n\t"
+		"nop\n"
+		"breakinst:\tbreak\n\t"
+		"nop\n\t"
+		".set\treorder");
+}
+
+static int compute_signal(int tt)
+{
+	struct hard_trap_info *ht;
+
+	for (ht = hard_trap_info; ht->tt && ht->signo; ht++)
+		if (ht->tt == tt)
+			return ht->signo;
+
+	return SIGHUP;		/* default for things we don't know about */
+}
+
+/*
+ * Similar to regs_to_gdb_regs() except that process is sleeping and so
+ * we may not be able to get all the info.
+ */
+void sleeping_thread_to_gdb_regs(unsigned long *gdb_regs, struct task_struct *p)
+{
+	int reg;
+#if (KGDB_GDB_REG_SIZE == 32)
+	u32 *ptr = (u32 *)gdb_regs;
+#else
+	u64 *ptr = (u64 *)gdb_regs;
+#endif
+
+	for (reg = 0; reg < 16; reg++)
+		*(ptr++) = 0;
+
+	/* S0 - S7 */
+	*(ptr++) = p->thread.reg16;
+	*(ptr++) = p->thread.reg17;
+	*(ptr++) = p->thread.reg18;
+	*(ptr++) = p->thread.reg19;
+	*(ptr++) = p->thread.reg20;
+	*(ptr++) = p->thread.reg21;
+	*(ptr++) = p->thread.reg22;
+	*(ptr++) = p->thread.reg23;
+
+	for (reg = 24; reg < 28; reg++)
+		*(ptr++) = 0;
+
+	/* GP, SP, FP, RA */
+	*(ptr++) = (long)p;
+	*(ptr++) = p->thread.reg29;
+	*(ptr++) = p->thread.reg30;
+	*(ptr++) = p->thread.reg31;
+
+	*(ptr++) = p->thread.cp0_status;
+
+	/* lo, hi */
+	*(ptr++) = 0;
+	*(ptr++) = 0;
+
+	/*
+	 * BadVAddr, Cause
+	 * Ideally these would come from the last exception frame up the stack
+	 * but that requires unwinding, otherwise we can't know much for sure.
+	 */
+	*(ptr++) = 0;
+	*(ptr++) = 0;
+
+	/*
+	 * PC
+	 * use return address (RA), i.e. the moment after return from resume()
+	 */
+	*(ptr++) = p->thread.reg31;
+}
+
+void kgdb_arch_set_pc(struct pt_regs *regs, unsigned long pc)
+{
+	regs->cp0_epc = pc;
+}
+
+/*
+ * Calls linux_debug_hook before the kernel dies. If KGDB is enabled,
+ * then try to fall into the debugger
+ */
+static int kgdb_mips_notify(struct notifier_block *self, unsigned long cmd,
+			    void *ptr)
+{
+	struct die_args *args = (struct die_args *)ptr;
+	struct pt_regs *regs = args->regs;
+	int trap = (regs->cp0_cause & 0x7c) >> 2;
+
+#ifdef CONFIG_KPROBES
+	/*
+	 * Return immediately if the kprobes fault notifier has set
+	 * DIE_PAGE_FAULT.
+	 */
+	if (cmd == DIE_PAGE_FAULT)
+		return NOTIFY_DONE;
+#endif /* CONFIG_KPROBES */
+
+	/* Userspace events, ignore. */
+	if (user_mode(regs))
+		return NOTIFY_DONE;
+
+	if (atomic_read(&kgdb_active) != -1)
+		kgdb_nmicallback(smp_processor_id(), regs);
+
+	if (kgdb_handle_exception(trap, compute_signal(trap), cmd, regs))
+		return NOTIFY_DONE;
+
+	if (atomic_read(&kgdb_setting_breakpoint))
+		if ((trap == 9) && (regs->cp0_epc == (unsigned long)breakinst))
+			regs->cp0_epc += 4;
+
+	/* In SMP mode, __flush_cache_all does IPI */
+	local_irq_enable();
+	__flush_cache_all();
+
+	return NOTIFY_STOP;
+}
+
+#ifdef CONFIG_KGDB_LOW_LEVEL_TRAP
+int kgdb_ll_trap(int cmd, const char *str,
+		 struct pt_regs *regs, long err, int trap, int sig)
+{
+	struct die_args args = {
+		.regs	= regs,
+		.str	= str,
+		.err	= err,
+		.trapnr = trap,
+		.signr	= sig,
+
+	};
+
+	if (!kgdb_io_module_registered)
+		return NOTIFY_DONE;
+
+	return kgdb_mips_notify(NULL, cmd, &args);
+}
+#endif /* CONFIG_KGDB_LOW_LEVEL_TRAP */
+
+static struct notifier_block kgdb_notifier = {
+	.notifier_call = kgdb_mips_notify,
+};
+
+/*
+ * Handle the 'c' command
+ */
+int kgdb_arch_handle_exception(int vector, int signo, int err_code,
+			       char *remcom_in_buffer, char *remcom_out_buffer,
+			       struct pt_regs *regs)
+{
+	char *ptr;
+	unsigned long address;
+
+	switch (remcom_in_buffer[0]) {
+	case 'c':
+		/* handle the optional parameter */
+		ptr = &remcom_in_buffer[1];
+		if (kgdb_hex2long(&ptr, &address))
+			regs->cp0_epc = address;
+
+		return 0;
+	}
+
+	return -1;
+}
+
+const struct kgdb_arch arch_kgdb_ops = {
+#ifdef CONFIG_CPU_BIG_ENDIAN
+	.gdb_bpt_instr = { spec_op << 2, 0x00, 0x00, break_op },
+#else
+	.gdb_bpt_instr = { break_op, 0x00, 0x00, spec_op << 2 },
+#endif
+};
+
+int kgdb_arch_init(void)
+{
+	register_die_notifier(&kgdb_notifier);
+
+	return 0;
+}
+
+/*
+ *	kgdb_arch_exit - Perform any architecture specific uninitalization.
+ *
+ *	This function will handle the uninitalization of any architecture
+ *	specific callbacks, for dynamic registration and unregistration.
+ */
+void kgdb_arch_exit(void)
+{
+	unregister_die_notifier(&kgdb_notifier);
+}
diff --git a/arch/mips/kernel/kprobes.c b/arch/mips/kernel/kprobes.c
new file mode 100644
index 000000000..316b27d0d
--- /dev/null
+++ b/arch/mips/kernel/kprobes.c
@@ -0,0 +1,525 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *  Kernel Probes (KProbes)
+ *  arch/mips/kernel/kprobes.c
+ *
+ *  Copyright 2006 Sony Corp.
+ *  Copyright 2010 Cavium Networks
+ *
+ *  Some portions copied from the powerpc version.
+ *
+ *   Copyright (C) IBM Corporation, 2002, 2004
+ */
+
+#define pr_fmt(fmt) "kprobes: " fmt
+
+#include <linux/kprobes.h>
+#include <linux/preempt.h>
+#include <linux/uaccess.h>
+#include <linux/kdebug.h>
+#include <linux/slab.h>
+
+#include <asm/ptrace.h>
+#include <asm/branch.h>
+#include <asm/break.h>
+
+#include "probes-common.h"
+
+static const union mips_instruction breakpoint_insn = {
+	.b_format = {
+		.opcode = spec_op,
+		.code = BRK_KPROBE_BP,
+		.func = break_op
+	}
+};
+
+static const union mips_instruction breakpoint2_insn = {
+	.b_format = {
+		.opcode = spec_op,
+		.code = BRK_KPROBE_SSTEPBP,
+		.func = break_op
+	}
+};
+
+DEFINE_PER_CPU(struct kprobe *, current_kprobe);
+DEFINE_PER_CPU(struct kprobe_ctlblk, kprobe_ctlblk);
+
+static int insn_has_delayslot(union mips_instruction insn)
+{
+	return __insn_has_delay_slot(insn);
+}
+NOKPROBE_SYMBOL(insn_has_delayslot);
+
+/*
+ * insn_has_ll_or_sc function checks whether instruction is ll or sc
+ * one; putting breakpoint on top of atomic ll/sc pair is bad idea;
+ * so we need to prevent it and refuse kprobes insertion for such
+ * instructions; cannot do much about breakpoint in the middle of
+ * ll/sc pair; it is upto user to avoid those places
+ */
+static int insn_has_ll_or_sc(union mips_instruction insn)
+{
+	int ret = 0;
+
+	switch (insn.i_format.opcode) {
+	case ll_op:
+	case lld_op:
+	case sc_op:
+	case scd_op:
+		ret = 1;
+		break;
+	default:
+		break;
+	}
+	return ret;
+}
+NOKPROBE_SYMBOL(insn_has_ll_or_sc);
+
+int arch_prepare_kprobe(struct kprobe *p)
+{
+	union mips_instruction insn;
+	union mips_instruction prev_insn;
+	int ret = 0;
+
+	insn = p->addr[0];
+
+	if (insn_has_ll_or_sc(insn)) {
+		pr_notice("Kprobes for ll and sc instructions are not supported\n");
+		ret = -EINVAL;
+		goto out;
+	}
+
+	if (copy_from_kernel_nofault(&prev_insn, p->addr - 1,
+			sizeof(mips_instruction)) == 0 &&
+	    insn_has_delayslot(prev_insn)) {
+		pr_notice("Kprobes for branch delayslot are not supported\n");
+		ret = -EINVAL;
+		goto out;
+	}
+
+	if (__insn_is_compact_branch(insn)) {
+		pr_notice("Kprobes for compact branches are not supported\n");
+		ret = -EINVAL;
+		goto out;
+	}
+
+	/* insn: must be on special executable page on mips. */
+	p->ainsn.insn = get_insn_slot();
+	if (!p->ainsn.insn) {
+		ret = -ENOMEM;
+		goto out;
+	}
+
+	/*
+	 * In the kprobe->ainsn.insn[] array we store the original
+	 * instruction at index zero and a break trap instruction at
+	 * index one.
+	 *
+	 * On MIPS arch if the instruction at probed address is a
+	 * branch instruction, we need to execute the instruction at
+	 * Branch Delayslot (BD) at the time of probe hit. As MIPS also
+	 * doesn't have single stepping support, the BD instruction can
+	 * not be executed in-line and it would be executed on SSOL slot
+	 * using a normal breakpoint instruction in the next slot.
+	 * So, read the instruction and save it for later execution.
+	 */
+	if (insn_has_delayslot(insn))
+		memcpy(&p->ainsn.insn[0], p->addr + 1, sizeof(kprobe_opcode_t));
+	else
+		memcpy(&p->ainsn.insn[0], p->addr, sizeof(kprobe_opcode_t));
+
+	p->ainsn.insn[1] = breakpoint2_insn;
+	p->opcode = *p->addr;
+
+out:
+	return ret;
+}
+NOKPROBE_SYMBOL(arch_prepare_kprobe);
+
+void arch_arm_kprobe(struct kprobe *p)
+{
+	*p->addr = breakpoint_insn;
+	flush_insn_slot(p);
+}
+NOKPROBE_SYMBOL(arch_arm_kprobe);
+
+void arch_disarm_kprobe(struct kprobe *p)
+{
+	*p->addr = p->opcode;
+	flush_insn_slot(p);
+}
+NOKPROBE_SYMBOL(arch_disarm_kprobe);
+
+void arch_remove_kprobe(struct kprobe *p)
+{
+	if (p->ainsn.insn) {
+		free_insn_slot(p->ainsn.insn, 0);
+		p->ainsn.insn = NULL;
+	}
+}
+NOKPROBE_SYMBOL(arch_remove_kprobe);
+
+static void save_previous_kprobe(struct kprobe_ctlblk *kcb)
+{
+	kcb->prev_kprobe.kp = kprobe_running();
+	kcb->prev_kprobe.status = kcb->kprobe_status;
+	kcb->prev_kprobe.old_SR = kcb->kprobe_old_SR;
+	kcb->prev_kprobe.saved_SR = kcb->kprobe_saved_SR;
+	kcb->prev_kprobe.saved_epc = kcb->kprobe_saved_epc;
+}
+
+static void restore_previous_kprobe(struct kprobe_ctlblk *kcb)
+{
+	__this_cpu_write(current_kprobe, kcb->prev_kprobe.kp);
+	kcb->kprobe_status = kcb->prev_kprobe.status;
+	kcb->kprobe_old_SR = kcb->prev_kprobe.old_SR;
+	kcb->kprobe_saved_SR = kcb->prev_kprobe.saved_SR;
+	kcb->kprobe_saved_epc = kcb->prev_kprobe.saved_epc;
+}
+
+static void set_current_kprobe(struct kprobe *p, struct pt_regs *regs,
+			       struct kprobe_ctlblk *kcb)
+{
+	__this_cpu_write(current_kprobe, p);
+	kcb->kprobe_saved_SR = kcb->kprobe_old_SR = (regs->cp0_status & ST0_IE);
+	kcb->kprobe_saved_epc = regs->cp0_epc;
+}
+
+/**
+ * evaluate_branch_instrucion -
+ *
+ * Evaluate the branch instruction at probed address during probe hit. The
+ * result of evaluation would be the updated epc. The insturction in delayslot
+ * would actually be single stepped using a normal breakpoint) on SSOL slot.
+ *
+ * The result is also saved in the kprobe control block for later use,
+ * in case we need to execute the delayslot instruction. The latter will be
+ * false for NOP instruction in dealyslot and the branch-likely instructions
+ * when the branch is taken. And for those cases we set a flag as
+ * SKIP_DELAYSLOT in the kprobe control block
+ */
+static int evaluate_branch_instruction(struct kprobe *p, struct pt_regs *regs,
+					struct kprobe_ctlblk *kcb)
+{
+	union mips_instruction insn = p->opcode;
+	long epc;
+	int ret = 0;
+
+	epc = regs->cp0_epc;
+	if (epc & 3)
+		goto unaligned;
+
+	if (p->ainsn.insn->word == 0)
+		kcb->flags |= SKIP_DELAYSLOT;
+	else
+		kcb->flags &= ~SKIP_DELAYSLOT;
+
+	ret = __compute_return_epc_for_insn(regs, insn);
+	if (ret < 0)
+		return ret;
+
+	if (ret == BRANCH_LIKELY_TAKEN)
+		kcb->flags |= SKIP_DELAYSLOT;
+
+	kcb->target_epc = regs->cp0_epc;
+
+	return 0;
+
+unaligned:
+	pr_notice("Failed to emulate branch instruction because of unaligned epc - sending SIGBUS to %s.\n", current->comm);
+	force_sig(SIGBUS);
+	return -EFAULT;
+
+}
+
+static void prepare_singlestep(struct kprobe *p, struct pt_regs *regs,
+						struct kprobe_ctlblk *kcb)
+{
+	int ret = 0;
+
+	regs->cp0_status &= ~ST0_IE;
+
+	/* single step inline if the instruction is a break */
+	if (p->opcode.word == breakpoint_insn.word ||
+	    p->opcode.word == breakpoint2_insn.word)
+		regs->cp0_epc = (unsigned long)p->addr;
+	else if (insn_has_delayslot(p->opcode)) {
+		ret = evaluate_branch_instruction(p, regs, kcb);
+		if (ret < 0)
+			return;
+	}
+	regs->cp0_epc = (unsigned long)&p->ainsn.insn[0];
+}
+
+/*
+ * Called after single-stepping.  p->addr is the address of the
+ * instruction whose first byte has been replaced by the "break 0"
+ * instruction.	 To avoid the SMP problems that can occur when we
+ * temporarily put back the original opcode to single-step, we
+ * single-stepped a copy of the instruction.  The address of this
+ * copy is p->ainsn.insn.
+ *
+ * This function prepares to return from the post-single-step
+ * breakpoint trap. In case of branch instructions, the target
+ * epc to be restored.
+ */
+static void resume_execution(struct kprobe *p,
+				       struct pt_regs *regs,
+				       struct kprobe_ctlblk *kcb)
+{
+	if (insn_has_delayslot(p->opcode))
+		regs->cp0_epc = kcb->target_epc;
+	else {
+		unsigned long orig_epc = kcb->kprobe_saved_epc;
+		regs->cp0_epc = orig_epc + 4;
+	}
+}
+NOKPROBE_SYMBOL(resume_execution);
+
+static int kprobe_handler(struct pt_regs *regs)
+{
+	struct kprobe *p;
+	int ret = 0;
+	kprobe_opcode_t *addr;
+	struct kprobe_ctlblk *kcb;
+
+	addr = (kprobe_opcode_t *) regs->cp0_epc;
+
+	/*
+	 * We don't want to be preempted for the entire
+	 * duration of kprobe processing
+	 */
+	preempt_disable();
+	kcb = get_kprobe_ctlblk();
+
+	/* Check we're not actually recursing */
+	if (kprobe_running()) {
+		p = get_kprobe(addr);
+		if (p) {
+			if (kcb->kprobe_status == KPROBE_HIT_SS &&
+			    p->ainsn.insn->word == breakpoint_insn.word) {
+				regs->cp0_status &= ~ST0_IE;
+				regs->cp0_status |= kcb->kprobe_saved_SR;
+				goto no_kprobe;
+			}
+			/*
+			 * We have reentered the kprobe_handler(), since
+			 * another probe was hit while within the handler.
+			 * We here save the original kprobes variables and
+			 * just single step on the instruction of the new probe
+			 * without calling any user handlers.
+			 */
+			save_previous_kprobe(kcb);
+			set_current_kprobe(p, regs, kcb);
+			kprobes_inc_nmissed_count(p);
+			prepare_singlestep(p, regs, kcb);
+			kcb->kprobe_status = KPROBE_REENTER;
+			if (kcb->flags & SKIP_DELAYSLOT) {
+				resume_execution(p, regs, kcb);
+				restore_previous_kprobe(kcb);
+				preempt_enable_no_resched();
+			}
+			return 1;
+		} else if (addr->word != breakpoint_insn.word) {
+			/*
+			 * The breakpoint instruction was removed by
+			 * another cpu right after we hit, no further
+			 * handling of this interrupt is appropriate
+			 */
+			ret = 1;
+		}
+		goto no_kprobe;
+	}
+
+	p = get_kprobe(addr);
+	if (!p) {
+		if (addr->word != breakpoint_insn.word) {
+			/*
+			 * The breakpoint instruction was removed right
+			 * after we hit it.  Another cpu has removed
+			 * either a probepoint or a debugger breakpoint
+			 * at this address.  In either case, no further
+			 * handling of this interrupt is appropriate.
+			 */
+			ret = 1;
+		}
+		/* Not one of ours: let kernel handle it */
+		goto no_kprobe;
+	}
+
+	set_current_kprobe(p, regs, kcb);
+	kcb->kprobe_status = KPROBE_HIT_ACTIVE;
+
+	if (p->pre_handler && p->pre_handler(p, regs)) {
+		/* handler has already set things up, so skip ss setup */
+		reset_current_kprobe();
+		preempt_enable_no_resched();
+		return 1;
+	}
+
+	prepare_singlestep(p, regs, kcb);
+	if (kcb->flags & SKIP_DELAYSLOT) {
+		kcb->kprobe_status = KPROBE_HIT_SSDONE;
+		if (p->post_handler)
+			p->post_handler(p, regs, 0);
+		resume_execution(p, regs, kcb);
+		preempt_enable_no_resched();
+	} else
+		kcb->kprobe_status = KPROBE_HIT_SS;
+
+	return 1;
+
+no_kprobe:
+	preempt_enable_no_resched();
+	return ret;
+
+}
+NOKPROBE_SYMBOL(kprobe_handler);
+
+static inline int post_kprobe_handler(struct pt_regs *regs)
+{
+	struct kprobe *cur = kprobe_running();
+	struct kprobe_ctlblk *kcb = get_kprobe_ctlblk();
+
+	if (!cur)
+		return 0;
+
+	if ((kcb->kprobe_status != KPROBE_REENTER) && cur->post_handler) {
+		kcb->kprobe_status = KPROBE_HIT_SSDONE;
+		cur->post_handler(cur, regs, 0);
+	}
+
+	resume_execution(cur, regs, kcb);
+
+	regs->cp0_status |= kcb->kprobe_saved_SR;
+
+	/* Restore back the original saved kprobes variables and continue. */
+	if (kcb->kprobe_status == KPROBE_REENTER) {
+		restore_previous_kprobe(kcb);
+		goto out;
+	}
+	reset_current_kprobe();
+out:
+	preempt_enable_no_resched();
+
+	return 1;
+}
+
+int kprobe_fault_handler(struct pt_regs *regs, int trapnr)
+{
+	struct kprobe *cur = kprobe_running();
+	struct kprobe_ctlblk *kcb = get_kprobe_ctlblk();
+
+	if (kcb->kprobe_status & KPROBE_HIT_SS) {
+		resume_execution(cur, regs, kcb);
+		regs->cp0_status |= kcb->kprobe_old_SR;
+
+		reset_current_kprobe();
+		preempt_enable_no_resched();
+	}
+	return 0;
+}
+
+/*
+ * Wrapper routine for handling exceptions.
+ */
+int kprobe_exceptions_notify(struct notifier_block *self,
+				       unsigned long val, void *data)
+{
+
+	struct die_args *args = (struct die_args *)data;
+	int ret = NOTIFY_DONE;
+
+	switch (val) {
+	case DIE_BREAK:
+		if (kprobe_handler(args->regs))
+			ret = NOTIFY_STOP;
+		break;
+	case DIE_SSTEPBP:
+		if (post_kprobe_handler(args->regs))
+			ret = NOTIFY_STOP;
+		break;
+
+	case DIE_PAGE_FAULT:
+		/* kprobe_running() needs smp_processor_id() */
+		preempt_disable();
+
+		if (kprobe_running()
+		    && kprobe_fault_handler(args->regs, args->trapnr))
+			ret = NOTIFY_STOP;
+		preempt_enable();
+		break;
+	default:
+		break;
+	}
+	return ret;
+}
+NOKPROBE_SYMBOL(kprobe_exceptions_notify);
+
+/*
+ * Function return probe trampoline:
+ *	- init_kprobes() establishes a probepoint here
+ *	- When the probed function returns, this probe causes the
+ *	  handlers to fire
+ */
+static void __used kretprobe_trampoline_holder(void)
+{
+	asm volatile(
+		".set push\n\t"
+		/* Keep the assembler from reordering and placing JR here. */
+		".set noreorder\n\t"
+		"nop\n\t"
+		".global __kretprobe_trampoline\n"
+		"__kretprobe_trampoline:\n\t"
+		"nop\n\t"
+		".set pop"
+		: : : "memory");
+}
+
+void __kretprobe_trampoline(void);
+
+void arch_prepare_kretprobe(struct kretprobe_instance *ri,
+				      struct pt_regs *regs)
+{
+	ri->ret_addr = (kprobe_opcode_t *) regs->regs[31];
+	ri->fp = NULL;
+
+	/* Replace the return addr with trampoline addr */
+	regs->regs[31] = (unsigned long)__kretprobe_trampoline;
+}
+NOKPROBE_SYMBOL(arch_prepare_kretprobe);
+
+/*
+ * Called when the probe at kretprobe trampoline is hit
+ */
+static int trampoline_probe_handler(struct kprobe *p,
+						struct pt_regs *regs)
+{
+	instruction_pointer(regs) = __kretprobe_trampoline_handler(regs, NULL);
+	/*
+	 * By returning a non-zero value, we are telling
+	 * kprobe_handler() that we don't want the post_handler
+	 * to run (and have re-enabled preemption)
+	 */
+	return 1;
+}
+NOKPROBE_SYMBOL(trampoline_probe_handler);
+
+int arch_trampoline_kprobe(struct kprobe *p)
+{
+	if (p->addr == (kprobe_opcode_t *)__kretprobe_trampoline)
+		return 1;
+
+	return 0;
+}
+NOKPROBE_SYMBOL(arch_trampoline_kprobe);
+
+static struct kprobe trampoline_p = {
+	.addr = (kprobe_opcode_t *)__kretprobe_trampoline,
+	.pre_handler = trampoline_probe_handler
+};
+
+int __init arch_init_kprobes(void)
+{
+	return register_kprobe(&trampoline_p);
+}
diff --git a/arch/mips/kernel/linux32.c b/arch/mips/kernel/linux32.c
new file mode 100644
index 000000000..6b61be486
--- /dev/null
+++ b/arch/mips/kernel/linux32.c
@@ -0,0 +1,133 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Conversion between 32-bit and 64-bit native system calls.
+ *
+ * Copyright (C) 2000 Silicon Graphics, Inc.
+ * Written by Ulf Carlsson (ulfc@engr.sgi.com)
+ */
+#include <linux/compiler.h>
+#include <linux/mm.h>
+#include <linux/errno.h>
+#include <linux/file.h>
+#include <linux/highuid.h>
+#include <linux/resource.h>
+#include <linux/highmem.h>
+#include <linux/time.h>
+#include <linux/times.h>
+#include <linux/poll.h>
+#include <linux/skbuff.h>
+#include <linux/filter.h>
+#include <linux/shm.h>
+#include <linux/sem.h>
+#include <linux/msg.h>
+#include <linux/icmpv6.h>
+#include <linux/syscalls.h>
+#include <linux/sysctl.h>
+#include <linux/utime.h>
+#include <linux/utsname.h>
+#include <linux/personality.h>
+#include <linux/dnotify.h>
+#include <linux/binfmts.h>
+#include <linux/security.h>
+#include <linux/compat.h>
+#include <linux/vfs.h>
+#include <linux/ipc.h>
+#include <linux/slab.h>
+
+#include <net/sock.h>
+#include <net/scm.h>
+
+#include <asm/compat-signal.h>
+#include <asm/sim.h>
+#include <linux/uaccess.h>
+#include <asm/mmu_context.h>
+#include <asm/mman.h>
+
+#ifdef __MIPSEB__
+#define merge_64(r1, r2) ((((r1) & 0xffffffffUL) << 32) + ((r2) & 0xffffffffUL))
+#endif
+#ifdef __MIPSEL__
+#define merge_64(r1, r2) ((((r2) & 0xffffffffUL) << 32) + ((r1) & 0xffffffffUL))
+#endif
+
+SYSCALL_DEFINE4(32_truncate64, const char __user *, path,
+	unsigned long, __dummy, unsigned long, a2, unsigned long, a3)
+{
+	return ksys_truncate(path, merge_64(a2, a3));
+}
+
+SYSCALL_DEFINE4(32_ftruncate64, unsigned long, fd, unsigned long, __dummy,
+	unsigned long, a2, unsigned long, a3)
+{
+	return ksys_ftruncate(fd, merge_64(a2, a3));
+}
+
+SYSCALL_DEFINE5(32_llseek, unsigned int, fd, unsigned int, offset_high,
+		unsigned int, offset_low, loff_t __user *, result,
+		unsigned int, origin)
+{
+	return sys_llseek(fd, offset_high, offset_low, result, origin);
+}
+
+/* From the Single Unix Spec: pread & pwrite act like lseek to pos + op +
+   lseek back to original location.  They fail just like lseek does on
+   non-seekable files.	*/
+
+SYSCALL_DEFINE6(32_pread, unsigned long, fd, char __user *, buf, size_t, count,
+	unsigned long, unused, unsigned long, a4, unsigned long, a5)
+{
+	return ksys_pread64(fd, buf, count, merge_64(a4, a5));
+}
+
+SYSCALL_DEFINE6(32_pwrite, unsigned int, fd, const char __user *, buf,
+	size_t, count, u32, unused, u64, a4, u64, a5)
+{
+	return ksys_pwrite64(fd, buf, count, merge_64(a4, a5));
+}
+
+SYSCALL_DEFINE1(32_personality, unsigned long, personality)
+{
+	unsigned int p = personality & 0xffffffff;
+	int ret;
+
+	if (personality(current->personality) == PER_LINUX32 &&
+	    personality(p) == PER_LINUX)
+		p = (p & ~PER_MASK) | PER_LINUX32;
+	ret = sys_personality(p);
+	if (ret != -1 && personality(ret) == PER_LINUX32)
+		ret = (ret & ~PER_MASK) | PER_LINUX;
+	return ret;
+}
+
+asmlinkage ssize_t sys32_readahead(int fd, u32 pad0, u64 a2, u64 a3,
+				   size_t count)
+{
+	return ksys_readahead(fd, merge_64(a2, a3), count);
+}
+
+asmlinkage long sys32_sync_file_range(int fd, int __pad,
+	unsigned long a2, unsigned long a3,
+	unsigned long a4, unsigned long a5,
+	int flags)
+{
+	return ksys_sync_file_range(fd,
+			merge_64(a2, a3), merge_64(a4, a5),
+			flags);
+}
+
+asmlinkage long sys32_fadvise64_64(int fd, int __pad,
+	unsigned long a2, unsigned long a3,
+	unsigned long a4, unsigned long a5,
+	int flags)
+{
+	return ksys_fadvise64_64(fd,
+			merge_64(a2, a3), merge_64(a4, a5),
+			flags);
+}
+
+asmlinkage long sys32_fallocate(int fd, int mode, unsigned offset_a2,
+	unsigned offset_a3, unsigned len_a4, unsigned len_a5)
+{
+	return ksys_fallocate(fd, mode, merge_64(offset_a2, offset_a3),
+			      merge_64(len_a4, len_a5));
+}
diff --git a/arch/mips/kernel/machine_kexec.c b/arch/mips/kernel/machine_kexec.c
new file mode 100644
index 000000000..432bfd3e7
--- /dev/null
+++ b/arch/mips/kernel/machine_kexec.c
@@ -0,0 +1,264 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * machine_kexec.c for kexec
+ * Created by <nschichan@corp.free.fr> on Thu Oct 12 15:15:06 2006
+ */
+#include <linux/compiler.h>
+#include <linux/kexec.h>
+#include <linux/mm.h>
+#include <linux/delay.h>
+#include <linux/libfdt.h>
+
+#include <asm/cacheflush.h>
+#include <asm/page.h>
+
+extern const unsigned char relocate_new_kernel[];
+extern const size_t relocate_new_kernel_size;
+
+extern unsigned long kexec_start_address;
+extern unsigned long kexec_indirection_page;
+
+static unsigned long reboot_code_buffer;
+
+#ifdef CONFIG_SMP
+static void (*relocated_kexec_smp_wait)(void *);
+
+atomic_t kexec_ready_to_reboot = ATOMIC_INIT(0);
+void (*_crash_smp_send_stop)(void) = NULL;
+#endif
+
+void (*_machine_kexec_shutdown)(void) = NULL;
+void (*_machine_crash_shutdown)(struct pt_regs *regs) = NULL;
+
+static void kexec_image_info(const struct kimage *kimage)
+{
+	unsigned long i;
+
+	pr_debug("kexec kimage info:\n");
+	pr_debug("  type:        %d\n", kimage->type);
+	pr_debug("  start:       %lx\n", kimage->start);
+	pr_debug("  head:        %lx\n", kimage->head);
+	pr_debug("  nr_segments: %lu\n", kimage->nr_segments);
+
+	for (i = 0; i < kimage->nr_segments; i++) {
+		pr_debug("    segment[%lu]: %016lx - %016lx, 0x%lx bytes, %lu pages\n",
+			i,
+			kimage->segment[i].mem,
+			kimage->segment[i].mem + kimage->segment[i].memsz,
+			(unsigned long)kimage->segment[i].memsz,
+			(unsigned long)kimage->segment[i].memsz /  PAGE_SIZE);
+	}
+}
+
+#ifdef CONFIG_UHI_BOOT
+
+static int uhi_machine_kexec_prepare(struct kimage *kimage)
+{
+	int i;
+
+	/*
+	 * In case DTB file is not passed to the new kernel, a flat device
+	 * tree will be created by kexec tool. It holds modified command
+	 * line for the new kernel.
+	 */
+	for (i = 0; i < kimage->nr_segments; i++) {
+		struct fdt_header fdt;
+
+		if (kimage->segment[i].memsz <= sizeof(fdt))
+			continue;
+
+		if (copy_from_user(&fdt, kimage->segment[i].buf, sizeof(fdt)))
+			continue;
+
+		if (fdt_check_header(&fdt))
+			continue;
+
+		kexec_args[0] = -2;
+		kexec_args[1] = (unsigned long)
+			phys_to_virt((unsigned long)kimage->segment[i].mem);
+		break;
+	}
+
+	return 0;
+}
+
+int (*_machine_kexec_prepare)(struct kimage *) = uhi_machine_kexec_prepare;
+
+#else
+
+int (*_machine_kexec_prepare)(struct kimage *) = NULL;
+
+#endif /* CONFIG_UHI_BOOT */
+
+int
+machine_kexec_prepare(struct kimage *kimage)
+{
+#ifdef CONFIG_SMP
+	if (!kexec_nonboot_cpu_func())
+		return -EINVAL;
+#endif
+
+	kexec_image_info(kimage);
+
+	if (_machine_kexec_prepare)
+		return _machine_kexec_prepare(kimage);
+
+	return 0;
+}
+
+void
+machine_kexec_cleanup(struct kimage *kimage)
+{
+}
+
+#ifdef CONFIG_SMP
+static void kexec_shutdown_secondary(void *param)
+{
+	int cpu = smp_processor_id();
+
+	if (!cpu_online(cpu))
+		return;
+
+	/* We won't be sent IPIs any more. */
+	set_cpu_online(cpu, false);
+
+	local_irq_disable();
+	while (!atomic_read(&kexec_ready_to_reboot))
+		cpu_relax();
+
+	kexec_reboot();
+
+	/* NOTREACHED */
+}
+#endif
+
+void
+machine_shutdown(void)
+{
+	if (_machine_kexec_shutdown)
+		_machine_kexec_shutdown();
+
+#ifdef CONFIG_SMP
+	smp_call_function(kexec_shutdown_secondary, NULL, 0);
+
+	while (num_online_cpus() > 1) {
+		cpu_relax();
+		mdelay(1);
+	}
+#endif
+}
+
+void
+machine_crash_shutdown(struct pt_regs *regs)
+{
+	if (_machine_crash_shutdown)
+		_machine_crash_shutdown(regs);
+	else
+		default_machine_crash_shutdown(regs);
+}
+
+#ifdef CONFIG_SMP
+void kexec_nonboot_cpu_jump(void)
+{
+	local_flush_icache_range((unsigned long)relocated_kexec_smp_wait,
+				 reboot_code_buffer + relocate_new_kernel_size);
+
+	relocated_kexec_smp_wait(NULL);
+}
+#endif
+
+void kexec_reboot(void)
+{
+	void (*do_kexec)(void) __noreturn;
+
+	/*
+	 * We know we were online, and there will be no incoming IPIs at
+	 * this point. Mark online again before rebooting so that the crash
+	 * analysis tool will see us correctly.
+	 */
+	set_cpu_online(smp_processor_id(), true);
+
+	/* Ensure remote CPUs observe that we're online before rebooting. */
+	smp_mb__after_atomic();
+
+#ifdef CONFIG_SMP
+	if (smp_processor_id() > 0) {
+		/*
+		 * Instead of cpu_relax() or wait, this is needed for kexec
+		 * smp reboot. Kdump usually doesn't require an smp new
+		 * kernel, but kexec may do.
+		 */
+		kexec_nonboot_cpu();
+
+		/* NOTREACHED */
+	}
+#endif
+
+	/*
+	 * Make sure we get correct instructions written by the
+	 * machine_kexec() CPU.
+	 */
+	local_flush_icache_range(reboot_code_buffer,
+				 reboot_code_buffer + relocate_new_kernel_size);
+
+	do_kexec = (void *)reboot_code_buffer;
+	do_kexec();
+}
+
+void
+machine_kexec(struct kimage *image)
+{
+	unsigned long entry;
+	unsigned long *ptr;
+
+	reboot_code_buffer =
+	  (unsigned long)page_address(image->control_code_page);
+
+	kexec_start_address =
+		(unsigned long) phys_to_virt(image->start);
+
+	if (image->type == KEXEC_TYPE_DEFAULT) {
+		kexec_indirection_page =
+			(unsigned long) phys_to_virt(image->head & PAGE_MASK);
+	} else {
+		kexec_indirection_page = (unsigned long)&image->head;
+	}
+
+	memcpy((void*)reboot_code_buffer, relocate_new_kernel,
+	       relocate_new_kernel_size);
+
+	/*
+	 * The generic kexec code builds a page list with physical
+	 * addresses. they are directly accessible through KSEG0 (or
+	 * CKSEG0 or XPHYS if on 64bit system), hence the
+	 * phys_to_virt() call.
+	 */
+	for (ptr = &image->head; (entry = *ptr) && !(entry &IND_DONE);
+	     ptr = (entry & IND_INDIRECTION) ?
+	       phys_to_virt(entry & PAGE_MASK) : ptr + 1) {
+		if (*ptr & IND_SOURCE || *ptr & IND_INDIRECTION ||
+		    *ptr & IND_DESTINATION)
+			*ptr = (unsigned long) phys_to_virt(*ptr);
+	}
+
+	/* Mark offline BEFORE disabling local irq. */
+	set_cpu_online(smp_processor_id(), false);
+
+	/*
+	 * we do not want to be bothered.
+	 */
+	local_irq_disable();
+
+	printk("Will call new kernel at %08lx\n", image->start);
+	printk("Bye ...\n");
+	/* Make reboot code buffer available to the boot CPU. */
+	__flush_cache_all();
+#ifdef CONFIG_SMP
+	/* All secondary cpus now may jump to kexec_wait cycle */
+	relocated_kexec_smp_wait = reboot_code_buffer +
+		(void *)(kexec_smp_wait - relocate_new_kernel);
+	smp_wmb();
+	atomic_set(&kexec_ready_to_reboot, 1);
+#endif
+	kexec_reboot();
+}
diff --git a/arch/mips/kernel/mcount.S b/arch/mips/kernel/mcount.S
new file mode 100644
index 000000000..cff52b283
--- /dev/null
+++ b/arch/mips/kernel/mcount.S
@@ -0,0 +1,220 @@
+/*
+ * MIPS specific _mcount support
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive for
+ * more details.
+ *
+ * Copyright (C) 2009 Lemote Inc. & DSLab, Lanzhou University, China
+ * Copyright (C) 2010 DSLab, Lanzhou University, China
+ * Author: Wu Zhangjin <wuzhangjin@gmail.com>
+ */
+
+#include <asm/export.h>
+#include <asm/regdef.h>
+#include <asm/stackframe.h>
+#include <asm/ftrace.h>
+
+	.text
+	.set noreorder
+	.set noat
+
+	.macro MCOUNT_SAVE_REGS
+	PTR_SUBU	sp, PT_SIZE
+	PTR_S	ra, PT_R31(sp)
+	PTR_S	AT, PT_R1(sp)
+	PTR_S	a0, PT_R4(sp)
+	PTR_S	a1, PT_R5(sp)
+	PTR_S	a2, PT_R6(sp)
+	PTR_S	a3, PT_R7(sp)
+#ifdef CONFIG_64BIT
+	PTR_S	a4, PT_R8(sp)
+	PTR_S	a5, PT_R9(sp)
+	PTR_S	a6, PT_R10(sp)
+	PTR_S	a7, PT_R11(sp)
+#endif
+	.endm
+
+	.macro MCOUNT_RESTORE_REGS
+	PTR_L	ra, PT_R31(sp)
+	PTR_L	AT, PT_R1(sp)
+	PTR_L	a0, PT_R4(sp)
+	PTR_L	a1, PT_R5(sp)
+	PTR_L	a2, PT_R6(sp)
+	PTR_L	a3, PT_R7(sp)
+#ifdef CONFIG_64BIT
+	PTR_L	a4, PT_R8(sp)
+	PTR_L	a5, PT_R9(sp)
+	PTR_L	a6, PT_R10(sp)
+	PTR_L	a7, PT_R11(sp)
+#endif
+	PTR_ADDIU	sp, PT_SIZE
+	.endm
+
+	.macro RETURN_BACK
+	jr ra
+	 move ra, AT
+	.endm
+
+/*
+ * The -mmcount-ra-address option of gcc 4.5 uses register $12 to pass
+ * the location of the parent's return address.
+ */
+#define MCOUNT_RA_ADDRESS_REG	$12
+
+#ifdef CONFIG_DYNAMIC_FTRACE
+
+NESTED(ftrace_caller, PT_SIZE, ra)
+	.globl _mcount
+_mcount:
+EXPORT_SYMBOL(_mcount)
+	b	ftrace_stub
+#ifdef CONFIG_32BIT
+	 addiu sp,sp,8
+#else
+	 nop
+#endif
+
+	/* When tracing is activated, it calls ftrace_caller+8 (aka here) */
+	MCOUNT_SAVE_REGS
+#ifdef KBUILD_MCOUNT_RA_ADDRESS
+	PTR_S	MCOUNT_RA_ADDRESS_REG, PT_R12(sp)
+#endif
+
+	PTR_SUBU a0, ra, 8	/* arg1: self address */
+	PTR_LA   t1, _stext
+	sltu     t2, a0, t1	/* t2 = (a0 < _stext) */
+	PTR_LA   t1, _etext
+	sltu     t3, t1, a0	/* t3 = (a0 > _etext) */
+	or       t1, t2, t3
+	beqz     t1, ftrace_call
+	 nop
+#if defined(KBUILD_MCOUNT_RA_ADDRESS) && defined(CONFIG_32BIT)
+	PTR_SUBU a0, a0, 16	/* arg1: adjust to module's recorded callsite */
+#else
+	PTR_SUBU a0, a0, 12
+#endif
+
+	.globl ftrace_call
+ftrace_call:
+	nop	/* a placeholder for the call to a real tracing function */
+	 move	a1, AT		/* arg2: parent's return address */
+
+#ifdef CONFIG_FUNCTION_GRAPH_TRACER
+	.globl ftrace_graph_call
+ftrace_graph_call:
+	nop
+	 nop
+#endif
+
+	MCOUNT_RESTORE_REGS
+	.globl ftrace_stub
+ftrace_stub:
+	RETURN_BACK
+	END(ftrace_caller)
+
+#else	/* ! CONFIG_DYNAMIC_FTRACE */
+
+NESTED(_mcount, PT_SIZE, ra)
+EXPORT_SYMBOL(_mcount)
+	PTR_LA	t1, ftrace_stub
+	PTR_L	t2, ftrace_trace_function /* Prepare t2 for (1) */
+	beq	t1, t2, fgraph_trace
+	 nop
+
+	MCOUNT_SAVE_REGS
+
+	move	a0, ra		/* arg1: self return address */
+	jalr	t2		/* (1) call *ftrace_trace_function */
+	 move	a1, AT		/* arg2: parent's return address */
+
+	MCOUNT_RESTORE_REGS
+
+fgraph_trace:
+#ifdef	CONFIG_FUNCTION_GRAPH_TRACER
+	PTR_LA	t1, ftrace_stub
+	PTR_L	t3, ftrace_graph_return
+	bne	t1, t3, ftrace_graph_caller
+	 nop
+	PTR_LA	t1, ftrace_graph_entry_stub
+	PTR_L	t3, ftrace_graph_entry
+	bne	t1, t3, ftrace_graph_caller
+	 nop
+#endif
+
+#ifdef CONFIG_32BIT
+	addiu sp, sp, 8
+#endif
+
+	.globl ftrace_stub
+ftrace_stub:
+	RETURN_BACK
+	END(_mcount)
+
+#endif	/* ! CONFIG_DYNAMIC_FTRACE */
+
+#ifdef CONFIG_FUNCTION_GRAPH_TRACER
+
+NESTED(ftrace_graph_caller, PT_SIZE, ra)
+#ifndef CONFIG_DYNAMIC_FTRACE
+	MCOUNT_SAVE_REGS
+#endif
+
+	/* arg1: Get the location of the parent's return address */
+#ifdef KBUILD_MCOUNT_RA_ADDRESS
+#ifdef CONFIG_DYNAMIC_FTRACE
+	PTR_L	a0, PT_R12(sp)
+#else
+	move	a0, MCOUNT_RA_ADDRESS_REG
+#endif
+	bnez	a0, 1f	/* non-leaf func: stored in MCOUNT_RA_ADDRESS_REG */
+	 nop
+#endif
+	PTR_LA	a0, PT_R1(sp)	/* leaf func: the location in current stack */
+1:
+
+	/* arg2: Get self return address */
+#ifdef CONFIG_DYNAMIC_FTRACE
+	PTR_L	a1, PT_R31(sp)
+#else
+	move	a1, ra
+#endif
+
+	/* arg3: Get frame pointer of current stack */
+#ifdef CONFIG_64BIT
+	PTR_LA	a2, PT_SIZE(sp)
+#else
+	PTR_LA	a2, (PT_SIZE+8)(sp)
+#endif
+
+	jal	prepare_ftrace_return
+	 nop
+	MCOUNT_RESTORE_REGS
+#ifndef CONFIG_DYNAMIC_FTRACE
+#ifdef CONFIG_32BIT
+	addiu sp, sp, 8
+#endif
+#endif
+	RETURN_BACK
+	END(ftrace_graph_caller)
+
+	.align	2
+	.globl	return_to_handler
+return_to_handler:
+	PTR_SUBU	sp, PT_SIZE
+	PTR_S	v0, PT_R2(sp)
+
+	jal	ftrace_return_to_handler
+	 PTR_S	v1, PT_R3(sp)
+
+	/* restore the real parent address: v0 -> ra */
+	move	ra, v0
+
+	PTR_L	v0, PT_R2(sp)
+	PTR_L	v1, PT_R3(sp)
+	jr	ra
+	 PTR_ADDIU	sp, PT_SIZE
+#endif /* CONFIG_FUNCTION_GRAPH_TRACER */
+
+	.set at
+	.set reorder
diff --git a/arch/mips/kernel/mips-cm.c b/arch/mips/kernel/mips-cm.c
new file mode 100644
index 000000000..b4f7d950c
--- /dev/null
+++ b/arch/mips/kernel/mips-cm.c
@@ -0,0 +1,515 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2013 Imagination Technologies
+ * Author: Paul Burton <paul.burton@mips.com>
+ */
+
+#include <linux/errno.h>
+#include <linux/percpu.h>
+#include <linux/spinlock.h>
+
+#include <asm/mips-cps.h>
+#include <asm/mipsregs.h>
+
+void __iomem *mips_gcr_base;
+void __iomem *mips_cm_l2sync_base;
+int mips_cm_is64;
+
+static char *cm2_tr[8] = {
+	"mem",	"gcr",	"gic",	"mmio",
+	"0x04", "cpc", "0x06", "0x07"
+};
+
+/* CM3 Tag ECC transaction type */
+static char *cm3_tr[16] = {
+	[0x0] = "ReqNoData",
+	[0x1] = "0x1",
+	[0x2] = "ReqWData",
+	[0x3] = "0x3",
+	[0x4] = "IReqNoResp",
+	[0x5] = "IReqWResp",
+	[0x6] = "IReqNoRespDat",
+	[0x7] = "IReqWRespDat",
+	[0x8] = "RespNoData",
+	[0x9] = "RespDataFol",
+	[0xa] = "RespWData",
+	[0xb] = "RespDataOnly",
+	[0xc] = "IRespNoData",
+	[0xd] = "IRespDataFol",
+	[0xe] = "IRespWData",
+	[0xf] = "IRespDataOnly"
+};
+
+static char *cm2_cmd[32] = {
+	[0x00] = "0x00",
+	[0x01] = "Legacy Write",
+	[0x02] = "Legacy Read",
+	[0x03] = "0x03",
+	[0x04] = "0x04",
+	[0x05] = "0x05",
+	[0x06] = "0x06",
+	[0x07] = "0x07",
+	[0x08] = "Coherent Read Own",
+	[0x09] = "Coherent Read Share",
+	[0x0a] = "Coherent Read Discard",
+	[0x0b] = "Coherent Ready Share Always",
+	[0x0c] = "Coherent Upgrade",
+	[0x0d] = "Coherent Writeback",
+	[0x0e] = "0x0e",
+	[0x0f] = "0x0f",
+	[0x10] = "Coherent Copyback",
+	[0x11] = "Coherent Copyback Invalidate",
+	[0x12] = "Coherent Invalidate",
+	[0x13] = "Coherent Write Invalidate",
+	[0x14] = "Coherent Completion Sync",
+	[0x15] = "0x15",
+	[0x16] = "0x16",
+	[0x17] = "0x17",
+	[0x18] = "0x18",
+	[0x19] = "0x19",
+	[0x1a] = "0x1a",
+	[0x1b] = "0x1b",
+	[0x1c] = "0x1c",
+	[0x1d] = "0x1d",
+	[0x1e] = "0x1e",
+	[0x1f] = "0x1f"
+};
+
+/* CM3 Tag ECC command type */
+static char *cm3_cmd[16] = {
+	[0x0] = "Legacy Read",
+	[0x1] = "Legacy Write",
+	[0x2] = "Coherent Read Own",
+	[0x3] = "Coherent Read Share",
+	[0x4] = "Coherent Read Discard",
+	[0x5] = "Coherent Evicted",
+	[0x6] = "Coherent Upgrade",
+	[0x7] = "Coherent Upgrade for Store Conditional",
+	[0x8] = "Coherent Writeback",
+	[0x9] = "Coherent Write Invalidate",
+	[0xa] = "0xa",
+	[0xb] = "0xb",
+	[0xc] = "0xc",
+	[0xd] = "0xd",
+	[0xe] = "0xe",
+	[0xf] = "0xf"
+};
+
+/* CM3 Tag ECC command group */
+static char *cm3_cmd_group[8] = {
+	[0x0] = "Normal",
+	[0x1] = "Registers",
+	[0x2] = "TLB",
+	[0x3] = "0x3",
+	[0x4] = "L1I",
+	[0x5] = "L1D",
+	[0x6] = "L3",
+	[0x7] = "L2"
+};
+
+static char *cm2_core[8] = {
+	"Invalid/OK",	"Invalid/Data",
+	"Shared/OK",	"Shared/Data",
+	"Modified/OK",	"Modified/Data",
+	"Exclusive/OK", "Exclusive/Data"
+};
+
+static char *cm2_l2_type[4] = {
+	[0x0] = "None",
+	[0x1] = "Tag RAM single/double ECC error",
+	[0x2] = "Data RAM single/double ECC error",
+	[0x3] = "WS RAM uncorrectable dirty parity"
+};
+
+static char *cm2_l2_instr[32] = {
+	[0x00] = "L2_NOP",
+	[0x01] = "L2_ERR_CORR",
+	[0x02] = "L2_TAG_INV",
+	[0x03] = "L2_WS_CLEAN",
+	[0x04] = "L2_RD_MDYFY_WR",
+	[0x05] = "L2_WS_MRU",
+	[0x06] = "L2_EVICT_LN2",
+	[0x07] = "0x07",
+	[0x08] = "L2_EVICT",
+	[0x09] = "L2_REFL",
+	[0x0a] = "L2_RD",
+	[0x0b] = "L2_WR",
+	[0x0c] = "L2_EVICT_MRU",
+	[0x0d] = "L2_SYNC",
+	[0x0e] = "L2_REFL_ERR",
+	[0x0f] = "0x0f",
+	[0x10] = "L2_INDX_WB_INV",
+	[0x11] = "L2_INDX_LD_TAG",
+	[0x12] = "L2_INDX_ST_TAG",
+	[0x13] = "L2_INDX_ST_DATA",
+	[0x14] = "L2_INDX_ST_ECC",
+	[0x15] = "0x15",
+	[0x16] = "0x16",
+	[0x17] = "0x17",
+	[0x18] = "L2_FTCH_AND_LCK",
+	[0x19] = "L2_HIT_INV",
+	[0x1a] = "L2_HIT_WB_INV",
+	[0x1b] = "L2_HIT_WB",
+	[0x1c] = "0x1c",
+	[0x1d] = "0x1d",
+	[0x1e] = "0x1e",
+	[0x1f] = "0x1f"
+};
+
+static char *cm2_causes[32] = {
+	"None", "GC_WR_ERR", "GC_RD_ERR", "COH_WR_ERR",
+	"COH_RD_ERR", "MMIO_WR_ERR", "MMIO_RD_ERR", "0x07",
+	"0x08", "0x09", "0x0a", "0x0b",
+	"0x0c", "0x0d", "0x0e", "0x0f",
+	"0x10", "INTVN_WR_ERR", "INTVN_RD_ERR", "0x13",
+	"0x14", "0x15", "0x16", "0x17",
+	"L2_RD_UNCORR", "L2_WR_UNCORR", "L2_CORR", "0x1b",
+	"0x1c", "0x1d", "0x1e", "0x1f"
+};
+
+static char *cm3_causes[32] = {
+	"0x0", "MP_CORRECTABLE_ECC_ERR", "MP_REQUEST_DECODE_ERR",
+	"MP_UNCORRECTABLE_ECC_ERR", "MP_PARITY_ERR", "MP_COHERENCE_ERR",
+	"CMBIU_REQUEST_DECODE_ERR", "CMBIU_PARITY_ERR", "CMBIU_AXI_RESP_ERR",
+	"0x9", "RBI_BUS_ERR", "0xb", "0xc", "0xd", "0xe", "0xf", "0x10",
+	"0x11", "0x12", "0x13", "0x14", "0x15", "0x16", "0x17", "0x18",
+	"0x19", "0x1a", "0x1b", "0x1c", "0x1d", "0x1e", "0x1f"
+};
+
+static DEFINE_PER_CPU_ALIGNED(spinlock_t, cm_core_lock);
+static DEFINE_PER_CPU_ALIGNED(unsigned long, cm_core_lock_flags);
+
+phys_addr_t __mips_cm_phys_base(void)
+{
+	u32 config3 = read_c0_config3();
+	unsigned long cmgcr;
+
+	/* Check the CMGCRBase register is implemented */
+	if (!(config3 & MIPS_CONF3_CMGCR))
+		return 0;
+
+	/* Read the address from CMGCRBase */
+	cmgcr = read_c0_cmgcrbase();
+	return (cmgcr & MIPS_CMGCRF_BASE) << (36 - 32);
+}
+
+phys_addr_t mips_cm_phys_base(void)
+	__attribute__((weak, alias("__mips_cm_phys_base")));
+
+phys_addr_t __mips_cm_l2sync_phys_base(void)
+{
+	u32 base_reg;
+
+	/*
+	 * If the L2-only sync region is already enabled then leave it at it's
+	 * current location.
+	 */
+	base_reg = read_gcr_l2_only_sync_base();
+	if (base_reg & CM_GCR_L2_ONLY_SYNC_BASE_SYNCEN)
+		return base_reg & CM_GCR_L2_ONLY_SYNC_BASE_SYNCBASE;
+
+	/* Default to following the CM */
+	return mips_cm_phys_base() + MIPS_CM_GCR_SIZE;
+}
+
+phys_addr_t mips_cm_l2sync_phys_base(void)
+	__attribute__((weak, alias("__mips_cm_l2sync_phys_base")));
+
+static void mips_cm_probe_l2sync(void)
+{
+	unsigned major_rev;
+	phys_addr_t addr;
+
+	/* L2-only sync was introduced with CM major revision 6 */
+	major_rev = FIELD_GET(CM_GCR_REV_MAJOR, read_gcr_rev());
+	if (major_rev < 6)
+		return;
+
+	/* Find a location for the L2 sync region */
+	addr = mips_cm_l2sync_phys_base();
+	BUG_ON((addr & CM_GCR_L2_ONLY_SYNC_BASE_SYNCBASE) != addr);
+	if (!addr)
+		return;
+
+	/* Set the region base address & enable it */
+	write_gcr_l2_only_sync_base(addr | CM_GCR_L2_ONLY_SYNC_BASE_SYNCEN);
+
+	/* Map the region */
+	mips_cm_l2sync_base = ioremap(addr, MIPS_CM_L2SYNC_SIZE);
+}
+
+int mips_cm_probe(void)
+{
+	phys_addr_t addr;
+	u32 base_reg;
+	unsigned cpu;
+
+	/*
+	 * No need to probe again if we have already been
+	 * here before.
+	 */
+	if (mips_gcr_base)
+		return 0;
+
+	addr = mips_cm_phys_base();
+	BUG_ON((addr & CM_GCR_BASE_GCRBASE) != addr);
+	if (!addr)
+		return -ENODEV;
+
+	mips_gcr_base = ioremap(addr, MIPS_CM_GCR_SIZE);
+	if (!mips_gcr_base)
+		return -ENXIO;
+
+	/* sanity check that we're looking at a CM */
+	base_reg = read_gcr_base();
+	if ((base_reg & CM_GCR_BASE_GCRBASE) != addr) {
+		pr_err("GCRs appear to have been moved (expected them at 0x%08lx)!\n",
+		       (unsigned long)addr);
+		iounmap(mips_gcr_base);
+		mips_gcr_base = NULL;
+		return -ENODEV;
+	}
+
+	/* set default target to memory */
+	change_gcr_base(CM_GCR_BASE_CMDEFTGT, CM_GCR_BASE_CMDEFTGT_MEM);
+
+	/* disable CM regions */
+	write_gcr_reg0_base(CM_GCR_REGn_BASE_BASEADDR);
+	write_gcr_reg0_mask(CM_GCR_REGn_MASK_ADDRMASK);
+	write_gcr_reg1_base(CM_GCR_REGn_BASE_BASEADDR);
+	write_gcr_reg1_mask(CM_GCR_REGn_MASK_ADDRMASK);
+	write_gcr_reg2_base(CM_GCR_REGn_BASE_BASEADDR);
+	write_gcr_reg2_mask(CM_GCR_REGn_MASK_ADDRMASK);
+	write_gcr_reg3_base(CM_GCR_REGn_BASE_BASEADDR);
+	write_gcr_reg3_mask(CM_GCR_REGn_MASK_ADDRMASK);
+
+	/* probe for an L2-only sync region */
+	mips_cm_probe_l2sync();
+
+	/* determine register width for this CM */
+	mips_cm_is64 = IS_ENABLED(CONFIG_64BIT) && (mips_cm_revision() >= CM_REV_CM3);
+
+	for_each_possible_cpu(cpu)
+		spin_lock_init(&per_cpu(cm_core_lock, cpu));
+
+	return 0;
+}
+
+void mips_cm_lock_other(unsigned int cluster, unsigned int core,
+			unsigned int vp, unsigned int block)
+{
+	unsigned int curr_core, cm_rev;
+	u32 val;
+
+	cm_rev = mips_cm_revision();
+	preempt_disable();
+
+	if (cm_rev >= CM_REV_CM3) {
+		val = FIELD_PREP(CM3_GCR_Cx_OTHER_CORE, core) |
+		      FIELD_PREP(CM3_GCR_Cx_OTHER_VP, vp);
+
+		if (cm_rev >= CM_REV_CM3_5) {
+			val |= CM_GCR_Cx_OTHER_CLUSTER_EN;
+			val |= FIELD_PREP(CM_GCR_Cx_OTHER_CLUSTER, cluster);
+			val |= FIELD_PREP(CM_GCR_Cx_OTHER_BLOCK, block);
+		} else {
+			WARN_ON(cluster != 0);
+			WARN_ON(block != CM_GCR_Cx_OTHER_BLOCK_LOCAL);
+		}
+
+		/*
+		 * We need to disable interrupts in SMP systems in order to
+		 * ensure that we don't interrupt the caller with code which
+		 * may modify the redirect register. We do so here in a
+		 * slightly obscure way by using a spin lock, since this has
+		 * the neat property of also catching any nested uses of
+		 * mips_cm_lock_other() leading to a deadlock or a nice warning
+		 * with lockdep enabled.
+		 */
+		spin_lock_irqsave(this_cpu_ptr(&cm_core_lock),
+				  *this_cpu_ptr(&cm_core_lock_flags));
+	} else {
+		WARN_ON(cluster != 0);
+		WARN_ON(block != CM_GCR_Cx_OTHER_BLOCK_LOCAL);
+
+		/*
+		 * We only have a GCR_CL_OTHER per core in systems with
+		 * CM 2.5 & older, so have to ensure other VP(E)s don't
+		 * race with us.
+		 */
+		curr_core = cpu_core(&current_cpu_data);
+		spin_lock_irqsave(&per_cpu(cm_core_lock, curr_core),
+				  per_cpu(cm_core_lock_flags, curr_core));
+
+		val = FIELD_PREP(CM_GCR_Cx_OTHER_CORENUM, core);
+	}
+
+	write_gcr_cl_other(val);
+
+	/*
+	 * Ensure the core-other region reflects the appropriate core &
+	 * VP before any accesses to it occur.
+	 */
+	mb();
+}
+
+void mips_cm_unlock_other(void)
+{
+	unsigned int curr_core;
+
+	if (mips_cm_revision() < CM_REV_CM3) {
+		curr_core = cpu_core(&current_cpu_data);
+		spin_unlock_irqrestore(&per_cpu(cm_core_lock, curr_core),
+				       per_cpu(cm_core_lock_flags, curr_core));
+	} else {
+		spin_unlock_irqrestore(this_cpu_ptr(&cm_core_lock),
+				       *this_cpu_ptr(&cm_core_lock_flags));
+	}
+
+	preempt_enable();
+}
+
+void mips_cm_error_report(void)
+{
+	u64 cm_error, cm_addr, cm_other;
+	unsigned long revision;
+	int ocause, cause;
+	char buf[256];
+
+	if (!mips_cm_present())
+		return;
+
+	revision = mips_cm_revision();
+	cm_error = read_gcr_error_cause();
+	cm_addr = read_gcr_error_addr();
+	cm_other = read_gcr_error_mult();
+
+	if (revision < CM_REV_CM3) { /* CM2 */
+		cause = FIELD_GET(CM_GCR_ERROR_CAUSE_ERRTYPE, cm_error);
+		ocause = FIELD_GET(CM_GCR_ERROR_MULT_ERR2ND, cm_other);
+
+		if (!cause)
+			return;
+
+		if (cause < 16) {
+			unsigned long cca_bits = (cm_error >> 15) & 7;
+			unsigned long tr_bits = (cm_error >> 12) & 7;
+			unsigned long cmd_bits = (cm_error >> 7) & 0x1f;
+			unsigned long stag_bits = (cm_error >> 3) & 15;
+			unsigned long sport_bits = (cm_error >> 0) & 7;
+
+			snprintf(buf, sizeof(buf),
+				 "CCA=%lu TR=%s MCmd=%s STag=%lu "
+				 "SPort=%lu\n", cca_bits, cm2_tr[tr_bits],
+				 cm2_cmd[cmd_bits], stag_bits, sport_bits);
+		} else if (cause < 24) {
+			/* glob state & sresp together */
+			unsigned long c3_bits = (cm_error >> 18) & 7;
+			unsigned long c2_bits = (cm_error >> 15) & 7;
+			unsigned long c1_bits = (cm_error >> 12) & 7;
+			unsigned long c0_bits = (cm_error >> 9) & 7;
+			unsigned long sc_bit = (cm_error >> 8) & 1;
+			unsigned long cmd_bits = (cm_error >> 3) & 0x1f;
+			unsigned long sport_bits = (cm_error >> 0) & 7;
+
+			snprintf(buf, sizeof(buf),
+				 "C3=%s C2=%s C1=%s C0=%s SC=%s "
+				 "MCmd=%s SPort=%lu\n",
+				 cm2_core[c3_bits], cm2_core[c2_bits],
+				 cm2_core[c1_bits], cm2_core[c0_bits],
+				 sc_bit ? "True" : "False",
+				 cm2_cmd[cmd_bits], sport_bits);
+		} else {
+			unsigned long muc_bit = (cm_error >> 23) & 1;
+			unsigned long ins_bits = (cm_error >> 18) & 0x1f;
+			unsigned long arr_bits = (cm_error >> 16) & 3;
+			unsigned long dw_bits = (cm_error >> 12) & 15;
+			unsigned long way_bits = (cm_error >> 9) & 7;
+			unsigned long mway_bit = (cm_error >> 8) & 1;
+			unsigned long syn_bits = (cm_error >> 0) & 0xFF;
+
+			snprintf(buf, sizeof(buf),
+				 "Type=%s%s Instr=%s DW=%lu Way=%lu "
+				 "MWay=%s Syndrome=0x%02lx",
+				 muc_bit ? "Multi-UC " : "",
+				 cm2_l2_type[arr_bits],
+				 cm2_l2_instr[ins_bits], dw_bits, way_bits,
+				 mway_bit ? "True" : "False", syn_bits);
+		}
+		pr_err("CM_ERROR=%08llx %s <%s>\n", cm_error,
+		       cm2_causes[cause], buf);
+		pr_err("CM_ADDR =%08llx\n", cm_addr);
+		pr_err("CM_OTHER=%08llx %s\n", cm_other, cm2_causes[ocause]);
+	} else { /* CM3 */
+		ulong core_id_bits, vp_id_bits, cmd_bits, cmd_group_bits;
+		ulong cm3_cca_bits, mcp_bits, cm3_tr_bits, sched_bit;
+
+		cause = FIELD_GET(CM3_GCR_ERROR_CAUSE_ERRTYPE, cm_error);
+		ocause = FIELD_GET(CM_GCR_ERROR_MULT_ERR2ND, cm_other);
+
+		if (!cause)
+			return;
+
+		/* Used by cause == {1,2,3} */
+		core_id_bits = (cm_error >> 22) & 0xf;
+		vp_id_bits = (cm_error >> 18) & 0xf;
+		cmd_bits = (cm_error >> 14) & 0xf;
+		cmd_group_bits = (cm_error >> 11) & 0xf;
+		cm3_cca_bits = (cm_error >> 8) & 7;
+		mcp_bits = (cm_error >> 5) & 0xf;
+		cm3_tr_bits = (cm_error >> 1) & 0xf;
+		sched_bit = cm_error & 0x1;
+
+		if (cause == 1 || cause == 3) { /* Tag ECC */
+			unsigned long tag_ecc = (cm_error >> 57) & 0x1;
+			unsigned long tag_way_bits = (cm_error >> 29) & 0xffff;
+			unsigned long dword_bits = (cm_error >> 49) & 0xff;
+			unsigned long data_way_bits = (cm_error >> 45) & 0xf;
+			unsigned long data_sets_bits = (cm_error >> 29) & 0xfff;
+			unsigned long bank_bit = (cm_error >> 28) & 0x1;
+			snprintf(buf, sizeof(buf),
+				 "%s ECC Error: Way=%lu (DWORD=%lu, Sets=%lu)"
+				 "Bank=%lu CoreID=%lu VPID=%lu Command=%s"
+				 "Command Group=%s CCA=%lu MCP=%d"
+				 "Transaction type=%s Scheduler=%lu\n",
+				 tag_ecc ? "TAG" : "DATA",
+				 tag_ecc ? (unsigned long)ffs(tag_way_bits) - 1 :
+				 data_way_bits, bank_bit, dword_bits,
+				 data_sets_bits,
+				 core_id_bits, vp_id_bits,
+				 cm3_cmd[cmd_bits],
+				 cm3_cmd_group[cmd_group_bits],
+				 cm3_cca_bits, 1 << mcp_bits,
+				 cm3_tr[cm3_tr_bits], sched_bit);
+		} else if (cause == 2) {
+			unsigned long data_error_type = (cm_error >> 41) & 0xfff;
+			unsigned long data_decode_cmd = (cm_error >> 37) & 0xf;
+			unsigned long data_decode_group = (cm_error >> 34) & 0x7;
+			unsigned long data_decode_destination_id = (cm_error >> 28) & 0x3f;
+
+			snprintf(buf, sizeof(buf),
+				 "Decode Request Error: Type=%lu, Command=%lu"
+				 "Command Group=%lu Destination ID=%lu"
+				 "CoreID=%lu VPID=%lu Command=%s"
+				 "Command Group=%s CCA=%lu MCP=%d"
+				 "Transaction type=%s Scheduler=%lu\n",
+				 data_error_type, data_decode_cmd,
+				 data_decode_group, data_decode_destination_id,
+				 core_id_bits, vp_id_bits,
+				 cm3_cmd[cmd_bits],
+				 cm3_cmd_group[cmd_group_bits],
+				 cm3_cca_bits, 1 << mcp_bits,
+				 cm3_tr[cm3_tr_bits], sched_bit);
+		} else {
+			buf[0] = 0;
+		}
+
+		pr_err("CM_ERROR=%llx %s <%s>\n", cm_error,
+		       cm3_causes[cause], buf);
+		pr_err("CM_ADDR =%llx\n", cm_addr);
+		pr_err("CM_OTHER=%llx %s\n", cm_other, cm3_causes[ocause]);
+	}
+
+	/* reprime cause register */
+	write_gcr_error_cause(cm_error);
+}
diff --git a/arch/mips/kernel/mips-cpc.c b/arch/mips/kernel/mips-cpc.c
new file mode 100644
index 000000000..3e386f7e1
--- /dev/null
+++ b/arch/mips/kernel/mips-cpc.c
@@ -0,0 +1,123 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2013 Imagination Technologies
+ * Author: Paul Burton <paul.burton@mips.com>
+ */
+
+#include <linux/bitfield.h>
+#include <linux/errno.h>
+#include <linux/percpu.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/spinlock.h>
+
+#include <asm/mips-cps.h>
+
+void __iomem *mips_cpc_base;
+
+static DEFINE_PER_CPU_ALIGNED(spinlock_t, cpc_core_lock);
+
+static DEFINE_PER_CPU_ALIGNED(unsigned long, cpc_core_lock_flags);
+
+phys_addr_t __weak mips_cpc_default_phys_base(void)
+{
+	struct device_node *cpc_node;
+	struct resource res;
+	int err;
+
+	cpc_node = of_find_compatible_node(of_root, NULL, "mti,mips-cpc");
+	if (cpc_node) {
+		err = of_address_to_resource(cpc_node, 0, &res);
+		of_node_put(cpc_node);
+		if (!err)
+			return res.start;
+	}
+
+	return 0;
+}
+
+/**
+ * mips_cpc_phys_base - retrieve the physical base address of the CPC
+ *
+ * This function returns the physical base address of the Cluster Power
+ * Controller memory mapped registers, or 0 if no Cluster Power Controller
+ * is present.
+ */
+static phys_addr_t mips_cpc_phys_base(void)
+{
+	unsigned long cpc_base;
+
+	if (!mips_cm_present())
+		return 0;
+
+	if (!(read_gcr_cpc_status() & CM_GCR_CPC_STATUS_EX))
+		return 0;
+
+	/* If the CPC is already enabled, leave it so */
+	cpc_base = read_gcr_cpc_base();
+	if (cpc_base & CM_GCR_CPC_BASE_CPCEN)
+		return cpc_base & CM_GCR_CPC_BASE_CPCBASE;
+
+	/* Otherwise, use the default address */
+	cpc_base = mips_cpc_default_phys_base();
+	if (!cpc_base)
+		return cpc_base;
+
+	/* Enable the CPC, mapped at the default address */
+	write_gcr_cpc_base(cpc_base | CM_GCR_CPC_BASE_CPCEN);
+	return cpc_base;
+}
+
+int mips_cpc_probe(void)
+{
+	phys_addr_t addr;
+	unsigned int cpu;
+
+	for_each_possible_cpu(cpu)
+		spin_lock_init(&per_cpu(cpc_core_lock, cpu));
+
+	addr = mips_cpc_phys_base();
+	if (!addr)
+		return -ENODEV;
+
+	mips_cpc_base = ioremap(addr, 0x8000);
+	if (!mips_cpc_base)
+		return -ENXIO;
+
+	return 0;
+}
+
+void mips_cpc_lock_other(unsigned int core)
+{
+	unsigned int curr_core;
+
+	if (mips_cm_revision() >= CM_REV_CM3)
+		/* Systems with CM >= 3 lock the CPC via mips_cm_lock_other */
+		return;
+
+	preempt_disable();
+	curr_core = cpu_core(&current_cpu_data);
+	spin_lock_irqsave(&per_cpu(cpc_core_lock, curr_core),
+			  per_cpu(cpc_core_lock_flags, curr_core));
+	write_cpc_cl_other(FIELD_PREP(CPC_Cx_OTHER_CORENUM, core));
+
+	/*
+	 * Ensure the core-other region reflects the appropriate core &
+	 * VP before any accesses to it occur.
+	 */
+	mb();
+}
+
+void mips_cpc_unlock_other(void)
+{
+	unsigned int curr_core;
+
+	if (mips_cm_revision() >= CM_REV_CM3)
+		/* Systems with CM >= 3 lock the CPC via mips_cm_lock_other */
+		return;
+
+	curr_core = cpu_core(&current_cpu_data);
+	spin_unlock_irqrestore(&per_cpu(cpc_core_lock, curr_core),
+			       per_cpu(cpc_core_lock_flags, curr_core));
+	preempt_enable();
+}
diff --git a/arch/mips/kernel/mips-mt-fpaff.c b/arch/mips/kernel/mips-mt-fpaff.c
new file mode 100644
index 000000000..67e130d3f
--- /dev/null
+++ b/arch/mips/kernel/mips-mt-fpaff.c
@@ -0,0 +1,219 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * General MIPS MT support routines, usable in AP/SP and SMVP.
+ * Copyright (C) 2005 Mips Technologies, Inc
+ */
+#include <linux/cpu.h>
+#include <linux/cpuset.h>
+#include <linux/cpumask.h>
+#include <linux/delay.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/sched.h>
+#include <linux/sched/task.h>
+#include <linux/cred.h>
+#include <linux/security.h>
+#include <linux/types.h>
+#include <linux/uaccess.h>
+
+/*
+ * CPU mask used to set process affinity for MT VPEs/TCs with FPUs
+ */
+cpumask_t mt_fpu_cpumask;
+
+static int fpaff_threshold = -1;
+unsigned long mt_fpemul_threshold;
+
+/*
+ * Replacement functions for the sys_sched_setaffinity() and
+ * sys_sched_getaffinity() system calls, so that we can integrate
+ * FPU affinity with the user's requested processor affinity.
+ * This code is 98% identical with the sys_sched_setaffinity()
+ * and sys_sched_getaffinity() system calls, and should be
+ * updated when kernel/sched/core.c changes.
+ */
+
+/*
+ * find_process_by_pid - find a process with a matching PID value.
+ * used in sys_sched_set/getaffinity() in kernel/sched/core.c, so
+ * cloned here.
+ */
+static inline struct task_struct *find_process_by_pid(pid_t pid)
+{
+	return pid ? find_task_by_vpid(pid) : current;
+}
+
+/*
+ * check the target process has a UID that matches the current process's
+ */
+static bool check_same_owner(struct task_struct *p)
+{
+	const struct cred *cred = current_cred(), *pcred;
+	bool match;
+
+	rcu_read_lock();
+	pcred = __task_cred(p);
+	match = (uid_eq(cred->euid, pcred->euid) ||
+		 uid_eq(cred->euid, pcred->uid));
+	rcu_read_unlock();
+	return match;
+}
+
+/*
+ * mipsmt_sys_sched_setaffinity - set the cpu affinity of a process
+ */
+asmlinkage long mipsmt_sys_sched_setaffinity(pid_t pid, unsigned int len,
+				      unsigned long __user *user_mask_ptr)
+{
+	cpumask_var_t cpus_allowed, new_mask, effective_mask;
+	struct thread_info *ti;
+	struct task_struct *p;
+	int retval;
+
+	if (len < sizeof(new_mask))
+		return -EINVAL;
+
+	if (copy_from_user(&new_mask, user_mask_ptr, sizeof(new_mask)))
+		return -EFAULT;
+
+	cpus_read_lock();
+	rcu_read_lock();
+
+	p = find_process_by_pid(pid);
+	if (!p) {
+		rcu_read_unlock();
+		cpus_read_unlock();
+		return -ESRCH;
+	}
+
+	/* Prevent p going away */
+	get_task_struct(p);
+	rcu_read_unlock();
+
+	if (!alloc_cpumask_var(&cpus_allowed, GFP_KERNEL)) {
+		retval = -ENOMEM;
+		goto out_put_task;
+	}
+	if (!alloc_cpumask_var(&new_mask, GFP_KERNEL)) {
+		retval = -ENOMEM;
+		goto out_free_cpus_allowed;
+	}
+	if (!alloc_cpumask_var(&effective_mask, GFP_KERNEL)) {
+		retval = -ENOMEM;
+		goto out_free_new_mask;
+	}
+	if (!check_same_owner(p) && !capable(CAP_SYS_NICE)) {
+		retval = -EPERM;
+		goto out_unlock;
+	}
+
+	retval = security_task_setscheduler(p);
+	if (retval)
+		goto out_unlock;
+
+	/* Record new user-specified CPU set for future reference */
+	cpumask_copy(&p->thread.user_cpus_allowed, new_mask);
+
+ again:
+	/* Compute new global allowed CPU set if necessary */
+	ti = task_thread_info(p);
+	if (test_ti_thread_flag(ti, TIF_FPUBOUND) &&
+	    cpumask_intersects(new_mask, &mt_fpu_cpumask)) {
+		cpumask_and(effective_mask, new_mask, &mt_fpu_cpumask);
+		retval = set_cpus_allowed_ptr(p, effective_mask);
+	} else {
+		cpumask_copy(effective_mask, new_mask);
+		clear_ti_thread_flag(ti, TIF_FPUBOUND);
+		retval = set_cpus_allowed_ptr(p, new_mask);
+	}
+
+	if (!retval) {
+		cpuset_cpus_allowed(p, cpus_allowed);
+		if (!cpumask_subset(effective_mask, cpus_allowed)) {
+			/*
+			 * We must have raced with a concurrent cpuset
+			 * update. Just reset the cpus_allowed to the
+			 * cpuset's cpus_allowed
+			 */
+			cpumask_copy(new_mask, cpus_allowed);
+			goto again;
+		}
+	}
+out_unlock:
+	free_cpumask_var(effective_mask);
+out_free_new_mask:
+	free_cpumask_var(new_mask);
+out_free_cpus_allowed:
+	free_cpumask_var(cpus_allowed);
+out_put_task:
+	put_task_struct(p);
+	cpus_read_unlock();
+	return retval;
+}
+
+/*
+ * mipsmt_sys_sched_getaffinity - get the cpu affinity of a process
+ */
+asmlinkage long mipsmt_sys_sched_getaffinity(pid_t pid, unsigned int len,
+				      unsigned long __user *user_mask_ptr)
+{
+	unsigned int real_len;
+	cpumask_t allowed, mask;
+	int retval;
+	struct task_struct *p;
+
+	real_len = sizeof(mask);
+	if (len < real_len)
+		return -EINVAL;
+
+	cpus_read_lock();
+	rcu_read_lock();
+
+	retval = -ESRCH;
+	p = find_process_by_pid(pid);
+	if (!p)
+		goto out_unlock;
+	retval = security_task_getscheduler(p);
+	if (retval)
+		goto out_unlock;
+
+	cpumask_or(&allowed, &p->thread.user_cpus_allowed, p->cpus_ptr);
+	cpumask_and(&mask, &allowed, cpu_active_mask);
+
+out_unlock:
+	rcu_read_unlock();
+	cpus_read_unlock();
+	if (retval)
+		return retval;
+	if (copy_to_user(user_mask_ptr, &mask, real_len))
+		return -EFAULT;
+	return real_len;
+}
+
+
+static int __init fpaff_thresh(char *str)
+{
+	get_option(&str, &fpaff_threshold);
+	return 1;
+}
+__setup("fpaff=", fpaff_thresh);
+
+/*
+ * FPU Use Factor empirically derived from experiments on 34K
+ */
+#define FPUSEFACTOR 2000
+
+static __init int mt_fp_affinity_init(void)
+{
+	if (fpaff_threshold >= 0) {
+		mt_fpemul_threshold = fpaff_threshold;
+	} else {
+		mt_fpemul_threshold =
+			(FPUSEFACTOR * (loops_per_jiffy/(500000/HZ))) / HZ;
+	}
+	printk(KERN_DEBUG "FPU Affinity set after %ld emulations\n",
+	       mt_fpemul_threshold);
+
+	return 0;
+}
+arch_initcall(mt_fp_affinity_init);
diff --git a/arch/mips/kernel/mips-mt.c b/arch/mips/kernel/mips-mt.c
new file mode 100644
index 000000000..dc023a979
--- /dev/null
+++ b/arch/mips/kernel/mips-mt.c
@@ -0,0 +1,246 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * General MIPS MT support routines, usable in AP/SP and SMVP.
+ * Copyright (C) 2005 Mips Technologies, Inc
+ */
+
+#include <linux/device.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/export.h>
+#include <linux/interrupt.h>
+#include <linux/security.h>
+
+#include <asm/cpu.h>
+#include <asm/processor.h>
+#include <linux/atomic.h>
+#include <asm/hardirq.h>
+#include <asm/mmu_context.h>
+#include <asm/mipsmtregs.h>
+#include <asm/r4kcache.h>
+#include <asm/cacheflush.h>
+
+int vpelimit;
+
+static int __init maxvpes(char *str)
+{
+	get_option(&str, &vpelimit);
+
+	return 1;
+}
+
+__setup("maxvpes=", maxvpes);
+
+int tclimit;
+
+static int __init maxtcs(char *str)
+{
+	get_option(&str, &tclimit);
+
+	return 1;
+}
+
+__setup("maxtcs=", maxtcs);
+
+/*
+ * Dump new MIPS MT state for the core. Does not leave TCs halted.
+ * Takes an argument which taken to be a pre-call MVPControl value.
+ */
+
+void mips_mt_regdump(unsigned long mvpctl)
+{
+	unsigned long flags;
+	unsigned long vpflags;
+	unsigned long mvpconf0;
+	int nvpe;
+	int ntc;
+	int i;
+	int tc;
+	unsigned long haltval;
+	unsigned long tcstatval;
+
+	local_irq_save(flags);
+	vpflags = dvpe();
+	printk("=== MIPS MT State Dump ===\n");
+	printk("-- Global State --\n");
+	printk("   MVPControl Passed: %08lx\n", mvpctl);
+	printk("   MVPControl Read: %08lx\n", vpflags);
+	printk("   MVPConf0 : %08lx\n", (mvpconf0 = read_c0_mvpconf0()));
+	nvpe = ((mvpconf0 & MVPCONF0_PVPE) >> MVPCONF0_PVPE_SHIFT) + 1;
+	ntc = ((mvpconf0 & MVPCONF0_PTC) >> MVPCONF0_PTC_SHIFT) + 1;
+	printk("-- per-VPE State --\n");
+	for (i = 0; i < nvpe; i++) {
+		for (tc = 0; tc < ntc; tc++) {
+			settc(tc);
+			if ((read_tc_c0_tcbind() & TCBIND_CURVPE) == i) {
+				printk("  VPE %d\n", i);
+				printk("   VPEControl : %08lx\n",
+				       read_vpe_c0_vpecontrol());
+				printk("   VPEConf0 : %08lx\n",
+				       read_vpe_c0_vpeconf0());
+				printk("   VPE%d.Status : %08lx\n",
+				       i, read_vpe_c0_status());
+				printk("   VPE%d.EPC : %08lx %pS\n",
+				       i, read_vpe_c0_epc(),
+				       (void *) read_vpe_c0_epc());
+				printk("   VPE%d.Cause : %08lx\n",
+				       i, read_vpe_c0_cause());
+				printk("   VPE%d.Config7 : %08lx\n",
+				       i, read_vpe_c0_config7());
+				break; /* Next VPE */
+			}
+		}
+	}
+	printk("-- per-TC State --\n");
+	for (tc = 0; tc < ntc; tc++) {
+		settc(tc);
+		if (read_tc_c0_tcbind() == read_c0_tcbind()) {
+			/* Are we dumping ourself?  */
+			haltval = 0; /* Then we're not halted, and mustn't be */
+			tcstatval = flags; /* And pre-dump TCStatus is flags */
+			printk("  TC %d (current TC with VPE EPC above)\n", tc);
+		} else {
+			haltval = read_tc_c0_tchalt();
+			write_tc_c0_tchalt(1);
+			tcstatval = read_tc_c0_tcstatus();
+			printk("  TC %d\n", tc);
+		}
+		printk("   TCStatus : %08lx\n", tcstatval);
+		printk("   TCBind : %08lx\n", read_tc_c0_tcbind());
+		printk("   TCRestart : %08lx %pS\n",
+		       read_tc_c0_tcrestart(), (void *) read_tc_c0_tcrestart());
+		printk("   TCHalt : %08lx\n", haltval);
+		printk("   TCContext : %08lx\n", read_tc_c0_tccontext());
+		if (!haltval)
+			write_tc_c0_tchalt(0);
+	}
+	printk("===========================\n");
+	evpe(vpflags);
+	local_irq_restore(flags);
+}
+
+static int mt_opt_rpsctl = -1;
+static int mt_opt_nblsu = -1;
+static int mt_opt_forceconfig7;
+static int mt_opt_config7 = -1;
+
+static int __init rpsctl_set(char *str)
+{
+	get_option(&str, &mt_opt_rpsctl);
+	return 1;
+}
+__setup("rpsctl=", rpsctl_set);
+
+static int __init nblsu_set(char *str)
+{
+	get_option(&str, &mt_opt_nblsu);
+	return 1;
+}
+__setup("nblsu=", nblsu_set);
+
+static int __init config7_set(char *str)
+{
+	get_option(&str, &mt_opt_config7);
+	mt_opt_forceconfig7 = 1;
+	return 1;
+}
+__setup("config7=", config7_set);
+
+static unsigned int itc_base;
+
+static int __init set_itc_base(char *str)
+{
+	get_option(&str, &itc_base);
+	return 1;
+}
+
+__setup("itcbase=", set_itc_base);
+
+void mips_mt_set_cpuoptions(void)
+{
+	unsigned int oconfig7 = read_c0_config7();
+	unsigned int nconfig7 = oconfig7;
+
+	if (mt_opt_rpsctl >= 0) {
+		printk("34K return prediction stack override set to %d.\n",
+			mt_opt_rpsctl);
+		if (mt_opt_rpsctl)
+			nconfig7 |= (1 << 2);
+		else
+			nconfig7 &= ~(1 << 2);
+	}
+	if (mt_opt_nblsu >= 0) {
+		printk("34K ALU/LSU sync override set to %d.\n", mt_opt_nblsu);
+		if (mt_opt_nblsu)
+			nconfig7 |= (1 << 5);
+		else
+			nconfig7 &= ~(1 << 5);
+	}
+	if (mt_opt_forceconfig7) {
+		printk("CP0.Config7 forced to 0x%08x.\n", mt_opt_config7);
+		nconfig7 = mt_opt_config7;
+	}
+	if (oconfig7 != nconfig7) {
+		__asm__ __volatile("sync");
+		write_c0_config7(nconfig7);
+		ehb();
+		printk("Config7: 0x%08x\n", read_c0_config7());
+	}
+
+	if (itc_base != 0) {
+		/*
+		 * Configure ITC mapping.  This code is very
+		 * specific to the 34K core family, which uses
+		 * a special mode bit ("ITC") in the ErrCtl
+		 * register to enable access to ITC control
+		 * registers via cache "tag" operations.
+		 */
+		unsigned long ectlval;
+		unsigned long itcblkgrn;
+
+		/* ErrCtl register is known as "ecc" to Linux */
+		ectlval = read_c0_ecc();
+		write_c0_ecc(ectlval | (0x1 << 26));
+		ehb();
+#define INDEX_0 (0x80000000)
+#define INDEX_8 (0x80000008)
+		/* Read "cache tag" for Dcache pseudo-index 8 */
+		cache_op(Index_Load_Tag_D, INDEX_8);
+		ehb();
+		itcblkgrn = read_c0_dtaglo();
+		itcblkgrn &= 0xfffe0000;
+		/* Set for 128 byte pitch of ITC cells */
+		itcblkgrn |= 0x00000c00;
+		/* Stage in Tag register */
+		write_c0_dtaglo(itcblkgrn);
+		ehb();
+		/* Write out to ITU with CACHE op */
+		cache_op(Index_Store_Tag_D, INDEX_8);
+		/* Now set base address, and turn ITC on with 0x1 bit */
+		write_c0_dtaglo((itc_base & 0xfffffc00) | 0x1 );
+		ehb();
+		/* Write out to ITU with CACHE op */
+		cache_op(Index_Store_Tag_D, INDEX_0);
+		write_c0_ecc(ectlval);
+		ehb();
+		printk("Mapped %ld ITC cells starting at 0x%08x\n",
+			((itcblkgrn & 0x7fe00000) >> 20), itc_base);
+	}
+}
+
+struct class *mt_class;
+
+static int __init mips_mt_init(void)
+{
+	struct class *mtc;
+
+	mtc = class_create(THIS_MODULE, "mt");
+	if (IS_ERR(mtc))
+		return PTR_ERR(mtc);
+
+	mt_class = mtc;
+
+	return 0;
+}
+
+subsys_initcall(mips_mt_init);
diff --git a/arch/mips/kernel/mips-r2-to-r6-emul.c b/arch/mips/kernel/mips-r2-to-r6-emul.c
new file mode 100644
index 000000000..750fe5698
--- /dev/null
+++ b/arch/mips/kernel/mips-r2-to-r6-emul.c
@@ -0,0 +1,2363 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (c) 2014 Imagination Technologies Ltd.
+ * Author: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
+ * Author: Markos Chandras <markos.chandras@imgtec.com>
+ *
+ *      MIPS R2 user space instruction emulator for MIPS R6
+ *
+ */
+#include <linux/bug.h>
+#include <linux/compiler.h>
+#include <linux/debugfs.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/ptrace.h>
+#include <linux/seq_file.h>
+
+#include <asm/asm.h>
+#include <asm/branch.h>
+#include <asm/break.h>
+#include <asm/debug.h>
+#include <asm/fpu.h>
+#include <asm/fpu_emulator.h>
+#include <asm/inst.h>
+#include <asm/mips-r2-to-r6-emul.h>
+#include <asm/local.h>
+#include <asm/mipsregs.h>
+#include <asm/ptrace.h>
+#include <linux/uaccess.h>
+
+#ifdef CONFIG_64BIT
+#define ADDIU	"daddiu "
+#define INS	"dins "
+#define EXT	"dext "
+#else
+#define ADDIU	"addiu "
+#define INS	"ins "
+#define EXT	"ext "
+#endif /* CONFIG_64BIT */
+
+#define SB	"sb "
+#define LB	"lb "
+#define LL	"ll "
+#define SC	"sc "
+
+#ifdef CONFIG_DEBUG_FS
+static DEFINE_PER_CPU(struct mips_r2_emulator_stats, mipsr2emustats);
+static DEFINE_PER_CPU(struct mips_r2_emulator_stats, mipsr2bdemustats);
+static DEFINE_PER_CPU(struct mips_r2br_emulator_stats, mipsr2bremustats);
+#endif
+
+extern const unsigned int fpucondbit[8];
+
+#define MIPS_R2_EMUL_TOTAL_PASS	10
+
+int mipsr2_emulation = 0;
+
+static int __init mipsr2emu_enable(char *s)
+{
+	mipsr2_emulation = 1;
+
+	pr_info("MIPS R2-to-R6 Emulator Enabled!");
+
+	return 1;
+}
+__setup("mipsr2emu", mipsr2emu_enable);
+
+/**
+ * mipsr6_emul - Emulate some frequent R2/R5/R6 instructions in delay slot
+ * for performance instead of the traditional way of using a stack trampoline
+ * which is rather slow.
+ * @regs: Process register set
+ * @ir: Instruction
+ */
+static inline int mipsr6_emul(struct pt_regs *regs, u32 ir)
+{
+	switch (MIPSInst_OPCODE(ir)) {
+	case addiu_op:
+		if (MIPSInst_RT(ir))
+			regs->regs[MIPSInst_RT(ir)] =
+				(s32)regs->regs[MIPSInst_RS(ir)] +
+				(s32)MIPSInst_SIMM(ir);
+		return 0;
+	case daddiu_op:
+		if (IS_ENABLED(CONFIG_32BIT))
+			break;
+
+		if (MIPSInst_RT(ir))
+			regs->regs[MIPSInst_RT(ir)] =
+				(s64)regs->regs[MIPSInst_RS(ir)] +
+				(s64)MIPSInst_SIMM(ir);
+		return 0;
+	case lwc1_op:
+	case swc1_op:
+	case cop1_op:
+	case cop1x_op:
+		/* FPU instructions in delay slot */
+		return -SIGFPE;
+	case spec_op:
+		switch (MIPSInst_FUNC(ir)) {
+		case or_op:
+			if (MIPSInst_RD(ir))
+				regs->regs[MIPSInst_RD(ir)] =
+					regs->regs[MIPSInst_RS(ir)] |
+					regs->regs[MIPSInst_RT(ir)];
+			return 0;
+		case sll_op:
+			if (MIPSInst_RS(ir))
+				break;
+
+			if (MIPSInst_RD(ir))
+				regs->regs[MIPSInst_RD(ir)] =
+					(s32)(((u32)regs->regs[MIPSInst_RT(ir)]) <<
+						MIPSInst_FD(ir));
+			return 0;
+		case srl_op:
+			if (MIPSInst_RS(ir))
+				break;
+
+			if (MIPSInst_RD(ir))
+				regs->regs[MIPSInst_RD(ir)] =
+					(s32)(((u32)regs->regs[MIPSInst_RT(ir)]) >>
+						MIPSInst_FD(ir));
+			return 0;
+		case addu_op:
+			if (MIPSInst_FD(ir))
+				break;
+
+			if (MIPSInst_RD(ir))
+				regs->regs[MIPSInst_RD(ir)] =
+					(s32)((u32)regs->regs[MIPSInst_RS(ir)] +
+					      (u32)regs->regs[MIPSInst_RT(ir)]);
+			return 0;
+		case subu_op:
+			if (MIPSInst_FD(ir))
+				break;
+
+			if (MIPSInst_RD(ir))
+				regs->regs[MIPSInst_RD(ir)] =
+					(s32)((u32)regs->regs[MIPSInst_RS(ir)] -
+					      (u32)regs->regs[MIPSInst_RT(ir)]);
+			return 0;
+		case dsll_op:
+			if (IS_ENABLED(CONFIG_32BIT) || MIPSInst_RS(ir))
+				break;
+
+			if (MIPSInst_RD(ir))
+				regs->regs[MIPSInst_RD(ir)] =
+					(s64)(((u64)regs->regs[MIPSInst_RT(ir)]) <<
+						MIPSInst_FD(ir));
+			return 0;
+		case dsrl_op:
+			if (IS_ENABLED(CONFIG_32BIT) || MIPSInst_RS(ir))
+				break;
+
+			if (MIPSInst_RD(ir))
+				regs->regs[MIPSInst_RD(ir)] =
+					(s64)(((u64)regs->regs[MIPSInst_RT(ir)]) >>
+						MIPSInst_FD(ir));
+			return 0;
+		case daddu_op:
+			if (IS_ENABLED(CONFIG_32BIT) || MIPSInst_FD(ir))
+				break;
+
+			if (MIPSInst_RD(ir))
+				regs->regs[MIPSInst_RD(ir)] =
+					(u64)regs->regs[MIPSInst_RS(ir)] +
+					(u64)regs->regs[MIPSInst_RT(ir)];
+			return 0;
+		case dsubu_op:
+			if (IS_ENABLED(CONFIG_32BIT) || MIPSInst_FD(ir))
+				break;
+
+			if (MIPSInst_RD(ir))
+				regs->regs[MIPSInst_RD(ir)] =
+					(s64)((u64)regs->regs[MIPSInst_RS(ir)] -
+					      (u64)regs->regs[MIPSInst_RT(ir)]);
+			return 0;
+		}
+		break;
+	default:
+		pr_debug("No fastpath BD emulation for instruction 0x%08x (op: %02x)\n",
+			 ir, MIPSInst_OPCODE(ir));
+	}
+
+	return SIGILL;
+}
+
+/**
+ * movf_func - Emulate a MOVF instruction
+ * @regs: Process register set
+ * @ir: Instruction
+ *
+ * Returns 0 since it always succeeds.
+ */
+static int movf_func(struct pt_regs *regs, u32 ir)
+{
+	u32 csr;
+	u32 cond;
+
+	csr = current->thread.fpu.fcr31;
+	cond = fpucondbit[MIPSInst_RT(ir) >> 2];
+
+	if (((csr & cond) == 0) && MIPSInst_RD(ir))
+		regs->regs[MIPSInst_RD(ir)] = regs->regs[MIPSInst_RS(ir)];
+
+	MIPS_R2_STATS(movs);
+
+	return 0;
+}
+
+/**
+ * movt_func - Emulate a MOVT instruction
+ * @regs: Process register set
+ * @ir: Instruction
+ *
+ * Returns 0 since it always succeeds.
+ */
+static int movt_func(struct pt_regs *regs, u32 ir)
+{
+	u32 csr;
+	u32 cond;
+
+	csr = current->thread.fpu.fcr31;
+	cond = fpucondbit[MIPSInst_RT(ir) >> 2];
+
+	if (((csr & cond) != 0) && MIPSInst_RD(ir))
+		regs->regs[MIPSInst_RD(ir)] = regs->regs[MIPSInst_RS(ir)];
+
+	MIPS_R2_STATS(movs);
+
+	return 0;
+}
+
+/**
+ * jr_func - Emulate a JR instruction.
+ * @pt_regs: Process register set
+ * @ir: Instruction
+ *
+ * Returns SIGILL if JR was in delay slot, SIGEMT if we
+ * can't compute the EPC, SIGSEGV if we can't access the
+ * userland instruction or 0 on success.
+ */
+static int jr_func(struct pt_regs *regs, u32 ir)
+{
+	int err;
+	unsigned long cepc, epc, nepc;
+	u32 nir;
+
+	if (delay_slot(regs))
+		return SIGILL;
+
+	/* EPC after the RI/JR instruction */
+	nepc = regs->cp0_epc;
+	/* Roll back to the reserved R2 JR instruction */
+	regs->cp0_epc -= 4;
+	epc = regs->cp0_epc;
+	err = __compute_return_epc(regs);
+
+	if (err < 0)
+		return SIGEMT;
+
+
+	/* Computed EPC */
+	cepc = regs->cp0_epc;
+
+	/* Get DS instruction */
+	err = __get_user(nir, (u32 __user *)nepc);
+	if (err)
+		return SIGSEGV;
+
+	MIPS_R2BR_STATS(jrs);
+
+	/* If nir == 0(NOP), then nothing else to do */
+	if (nir) {
+		/*
+		 * Negative err means FPU instruction in BD-slot,
+		 * Zero err means 'BD-slot emulation done'
+		 * For anything else we go back to trampoline emulation.
+		 */
+		err = mipsr6_emul(regs, nir);
+		if (err > 0) {
+			regs->cp0_epc = nepc;
+			err = mips_dsemul(regs, nir, epc, cepc);
+			if (err == SIGILL)
+				err = SIGEMT;
+			MIPS_R2_STATS(dsemul);
+		}
+	}
+
+	return err;
+}
+
+/**
+ * movz_func - Emulate a MOVZ instruction
+ * @regs: Process register set
+ * @ir: Instruction
+ *
+ * Returns 0 since it always succeeds.
+ */
+static int movz_func(struct pt_regs *regs, u32 ir)
+{
+	if (((regs->regs[MIPSInst_RT(ir)]) == 0) && MIPSInst_RD(ir))
+		regs->regs[MIPSInst_RD(ir)] = regs->regs[MIPSInst_RS(ir)];
+	MIPS_R2_STATS(movs);
+
+	return 0;
+}
+
+/**
+ * movn_func - Emulate a MOVZ instruction
+ * @regs: Process register set
+ * @ir: Instruction
+ *
+ * Returns 0 since it always succeeds.
+ */
+static int movn_func(struct pt_regs *regs, u32 ir)
+{
+	if (((regs->regs[MIPSInst_RT(ir)]) != 0) && MIPSInst_RD(ir))
+		regs->regs[MIPSInst_RD(ir)] = regs->regs[MIPSInst_RS(ir)];
+	MIPS_R2_STATS(movs);
+
+	return 0;
+}
+
+/**
+ * mfhi_func - Emulate a MFHI instruction
+ * @regs: Process register set
+ * @ir: Instruction
+ *
+ * Returns 0 since it always succeeds.
+ */
+static int mfhi_func(struct pt_regs *regs, u32 ir)
+{
+	if (MIPSInst_RD(ir))
+		regs->regs[MIPSInst_RD(ir)] = regs->hi;
+
+	MIPS_R2_STATS(hilo);
+
+	return 0;
+}
+
+/**
+ * mthi_func - Emulate a MTHI instruction
+ * @regs: Process register set
+ * @ir: Instruction
+ *
+ * Returns 0 since it always succeeds.
+ */
+static int mthi_func(struct pt_regs *regs, u32 ir)
+{
+	regs->hi = regs->regs[MIPSInst_RS(ir)];
+
+	MIPS_R2_STATS(hilo);
+
+	return 0;
+}
+
+/**
+ * mflo_func - Emulate a MFLO instruction
+ * @regs: Process register set
+ * @ir: Instruction
+ *
+ * Returns 0 since it always succeeds.
+ */
+static int mflo_func(struct pt_regs *regs, u32 ir)
+{
+	if (MIPSInst_RD(ir))
+		regs->regs[MIPSInst_RD(ir)] = regs->lo;
+
+	MIPS_R2_STATS(hilo);
+
+	return 0;
+}
+
+/**
+ * mtlo_func - Emulate a MTLO instruction
+ * @regs: Process register set
+ * @ir: Instruction
+ *
+ * Returns 0 since it always succeeds.
+ */
+static int mtlo_func(struct pt_regs *regs, u32 ir)
+{
+	regs->lo = regs->regs[MIPSInst_RS(ir)];
+
+	MIPS_R2_STATS(hilo);
+
+	return 0;
+}
+
+/**
+ * mult_func - Emulate a MULT instruction
+ * @regs: Process register set
+ * @ir: Instruction
+ *
+ * Returns 0 since it always succeeds.
+ */
+static int mult_func(struct pt_regs *regs, u32 ir)
+{
+	s64 res;
+	s32 rt, rs;
+
+	rt = regs->regs[MIPSInst_RT(ir)];
+	rs = regs->regs[MIPSInst_RS(ir)];
+	res = (s64)rt * (s64)rs;
+
+	rs = res;
+	regs->lo = (s64)rs;
+	rt = res >> 32;
+	res = (s64)rt;
+	regs->hi = res;
+
+	MIPS_R2_STATS(muls);
+
+	return 0;
+}
+
+/**
+ * multu_func - Emulate a MULTU instruction
+ * @regs: Process register set
+ * @ir: Instruction
+ *
+ * Returns 0 since it always succeeds.
+ */
+static int multu_func(struct pt_regs *regs, u32 ir)
+{
+	u64 res;
+	u32 rt, rs;
+
+	rt = regs->regs[MIPSInst_RT(ir)];
+	rs = regs->regs[MIPSInst_RS(ir)];
+	res = (u64)rt * (u64)rs;
+	rt = res;
+	regs->lo = (s64)(s32)rt;
+	regs->hi = (s64)(s32)(res >> 32);
+
+	MIPS_R2_STATS(muls);
+
+	return 0;
+}
+
+/**
+ * div_func - Emulate a DIV instruction
+ * @regs: Process register set
+ * @ir: Instruction
+ *
+ * Returns 0 since it always succeeds.
+ */
+static int div_func(struct pt_regs *regs, u32 ir)
+{
+	s32 rt, rs;
+
+	rt = regs->regs[MIPSInst_RT(ir)];
+	rs = regs->regs[MIPSInst_RS(ir)];
+
+	regs->lo = (s64)(rs / rt);
+	regs->hi = (s64)(rs % rt);
+
+	MIPS_R2_STATS(divs);
+
+	return 0;
+}
+
+/**
+ * divu_func - Emulate a DIVU instruction
+ * @regs: Process register set
+ * @ir: Instruction
+ *
+ * Returns 0 since it always succeeds.
+ */
+static int divu_func(struct pt_regs *regs, u32 ir)
+{
+	u32 rt, rs;
+
+	rt = regs->regs[MIPSInst_RT(ir)];
+	rs = regs->regs[MIPSInst_RS(ir)];
+
+	regs->lo = (s64)(rs / rt);
+	regs->hi = (s64)(rs % rt);
+
+	MIPS_R2_STATS(divs);
+
+	return 0;
+}
+
+/**
+ * dmult_func - Emulate a DMULT instruction
+ * @regs: Process register set
+ * @ir: Instruction
+ *
+ * Returns 0 on success or SIGILL for 32-bit kernels.
+ */
+static int dmult_func(struct pt_regs *regs, u32 ir)
+{
+	s64 res;
+	s64 rt, rs;
+
+	if (IS_ENABLED(CONFIG_32BIT))
+		return SIGILL;
+
+	rt = regs->regs[MIPSInst_RT(ir)];
+	rs = regs->regs[MIPSInst_RS(ir)];
+	res = rt * rs;
+
+	regs->lo = res;
+	__asm__ __volatile__(
+		"dmuh %0, %1, %2\t\n"
+		: "=r"(res)
+		: "r"(rt), "r"(rs));
+
+	regs->hi = res;
+
+	MIPS_R2_STATS(muls);
+
+	return 0;
+}
+
+/**
+ * dmultu_func - Emulate a DMULTU instruction
+ * @regs: Process register set
+ * @ir: Instruction
+ *
+ * Returns 0 on success or SIGILL for 32-bit kernels.
+ */
+static int dmultu_func(struct pt_regs *regs, u32 ir)
+{
+	u64 res;
+	u64 rt, rs;
+
+	if (IS_ENABLED(CONFIG_32BIT))
+		return SIGILL;
+
+	rt = regs->regs[MIPSInst_RT(ir)];
+	rs = regs->regs[MIPSInst_RS(ir)];
+	res = rt * rs;
+
+	regs->lo = res;
+	__asm__ __volatile__(
+		"dmuhu %0, %1, %2\t\n"
+		: "=r"(res)
+		: "r"(rt), "r"(rs));
+
+	regs->hi = res;
+
+	MIPS_R2_STATS(muls);
+
+	return 0;
+}
+
+/**
+ * ddiv_func - Emulate a DDIV instruction
+ * @regs: Process register set
+ * @ir: Instruction
+ *
+ * Returns 0 on success or SIGILL for 32-bit kernels.
+ */
+static int ddiv_func(struct pt_regs *regs, u32 ir)
+{
+	s64 rt, rs;
+
+	if (IS_ENABLED(CONFIG_32BIT))
+		return SIGILL;
+
+	rt = regs->regs[MIPSInst_RT(ir)];
+	rs = regs->regs[MIPSInst_RS(ir)];
+
+	regs->lo = rs / rt;
+	regs->hi = rs % rt;
+
+	MIPS_R2_STATS(divs);
+
+	return 0;
+}
+
+/**
+ * ddivu_func - Emulate a DDIVU instruction
+ * @regs: Process register set
+ * @ir: Instruction
+ *
+ * Returns 0 on success or SIGILL for 32-bit kernels.
+ */
+static int ddivu_func(struct pt_regs *regs, u32 ir)
+{
+	u64 rt, rs;
+
+	if (IS_ENABLED(CONFIG_32BIT))
+		return SIGILL;
+
+	rt = regs->regs[MIPSInst_RT(ir)];
+	rs = regs->regs[MIPSInst_RS(ir)];
+
+	regs->lo = rs / rt;
+	regs->hi = rs % rt;
+
+	MIPS_R2_STATS(divs);
+
+	return 0;
+}
+
+/* R6 removed instructions for the SPECIAL opcode */
+static const struct r2_decoder_table spec_op_table[] = {
+	{ 0xfc1ff83f, 0x00000008, jr_func },
+	{ 0xfc00ffff, 0x00000018, mult_func },
+	{ 0xfc00ffff, 0x00000019, multu_func },
+	{ 0xfc00ffff, 0x0000001c, dmult_func },
+	{ 0xfc00ffff, 0x0000001d, dmultu_func },
+	{ 0xffff07ff, 0x00000010, mfhi_func },
+	{ 0xfc1fffff, 0x00000011, mthi_func },
+	{ 0xffff07ff, 0x00000012, mflo_func },
+	{ 0xfc1fffff, 0x00000013, mtlo_func },
+	{ 0xfc0307ff, 0x00000001, movf_func },
+	{ 0xfc0307ff, 0x00010001, movt_func },
+	{ 0xfc0007ff, 0x0000000a, movz_func },
+	{ 0xfc0007ff, 0x0000000b, movn_func },
+	{ 0xfc00ffff, 0x0000001a, div_func },
+	{ 0xfc00ffff, 0x0000001b, divu_func },
+	{ 0xfc00ffff, 0x0000001e, ddiv_func },
+	{ 0xfc00ffff, 0x0000001f, ddivu_func },
+	{}
+};
+
+/**
+ * madd_func - Emulate a MADD instruction
+ * @regs: Process register set
+ * @ir: Instruction
+ *
+ * Returns 0 since it always succeeds.
+ */
+static int madd_func(struct pt_regs *regs, u32 ir)
+{
+	s64 res;
+	s32 rt, rs;
+
+	rt = regs->regs[MIPSInst_RT(ir)];
+	rs = regs->regs[MIPSInst_RS(ir)];
+	res = (s64)rt * (s64)rs;
+	rt = regs->hi;
+	rs = regs->lo;
+	res += ((((s64)rt) << 32) | (u32)rs);
+
+	rt = res;
+	regs->lo = (s64)rt;
+	rs = res >> 32;
+	regs->hi = (s64)rs;
+
+	MIPS_R2_STATS(dsps);
+
+	return 0;
+}
+
+/**
+ * maddu_func - Emulate a MADDU instruction
+ * @regs: Process register set
+ * @ir: Instruction
+ *
+ * Returns 0 since it always succeeds.
+ */
+static int maddu_func(struct pt_regs *regs, u32 ir)
+{
+	u64 res;
+	u32 rt, rs;
+
+	rt = regs->regs[MIPSInst_RT(ir)];
+	rs = regs->regs[MIPSInst_RS(ir)];
+	res = (u64)rt * (u64)rs;
+	rt = regs->hi;
+	rs = regs->lo;
+	res += ((((s64)rt) << 32) | (u32)rs);
+
+	rt = res;
+	regs->lo = (s64)(s32)rt;
+	rs = res >> 32;
+	regs->hi = (s64)(s32)rs;
+
+	MIPS_R2_STATS(dsps);
+
+	return 0;
+}
+
+/**
+ * msub_func - Emulate a MSUB instruction
+ * @regs: Process register set
+ * @ir: Instruction
+ *
+ * Returns 0 since it always succeeds.
+ */
+static int msub_func(struct pt_regs *regs, u32 ir)
+{
+	s64 res;
+	s32 rt, rs;
+
+	rt = regs->regs[MIPSInst_RT(ir)];
+	rs = regs->regs[MIPSInst_RS(ir)];
+	res = (s64)rt * (s64)rs;
+	rt = regs->hi;
+	rs = regs->lo;
+	res = ((((s64)rt) << 32) | (u32)rs) - res;
+
+	rt = res;
+	regs->lo = (s64)rt;
+	rs = res >> 32;
+	regs->hi = (s64)rs;
+
+	MIPS_R2_STATS(dsps);
+
+	return 0;
+}
+
+/**
+ * msubu_func - Emulate a MSUBU instruction
+ * @regs: Process register set
+ * @ir: Instruction
+ *
+ * Returns 0 since it always succeeds.
+ */
+static int msubu_func(struct pt_regs *regs, u32 ir)
+{
+	u64 res;
+	u32 rt, rs;
+
+	rt = regs->regs[MIPSInst_RT(ir)];
+	rs = regs->regs[MIPSInst_RS(ir)];
+	res = (u64)rt * (u64)rs;
+	rt = regs->hi;
+	rs = regs->lo;
+	res = ((((s64)rt) << 32) | (u32)rs) - res;
+
+	rt = res;
+	regs->lo = (s64)(s32)rt;
+	rs = res >> 32;
+	regs->hi = (s64)(s32)rs;
+
+	MIPS_R2_STATS(dsps);
+
+	return 0;
+}
+
+/**
+ * mul_func - Emulate a MUL instruction
+ * @regs: Process register set
+ * @ir: Instruction
+ *
+ * Returns 0 since it always succeeds.
+ */
+static int mul_func(struct pt_regs *regs, u32 ir)
+{
+	s64 res;
+	s32 rt, rs;
+
+	if (!MIPSInst_RD(ir))
+		return 0;
+	rt = regs->regs[MIPSInst_RT(ir)];
+	rs = regs->regs[MIPSInst_RS(ir)];
+	res = (s64)rt * (s64)rs;
+
+	rs = res;
+	regs->regs[MIPSInst_RD(ir)] = (s64)rs;
+
+	MIPS_R2_STATS(muls);
+
+	return 0;
+}
+
+/**
+ * clz_func - Emulate a CLZ instruction
+ * @regs: Process register set
+ * @ir: Instruction
+ *
+ * Returns 0 since it always succeeds.
+ */
+static int clz_func(struct pt_regs *regs, u32 ir)
+{
+	u32 res;
+	u32 rs;
+
+	if (!MIPSInst_RD(ir))
+		return 0;
+
+	rs = regs->regs[MIPSInst_RS(ir)];
+	__asm__ __volatile__("clz %0, %1" : "=r"(res) : "r"(rs));
+	regs->regs[MIPSInst_RD(ir)] = res;
+
+	MIPS_R2_STATS(bops);
+
+	return 0;
+}
+
+/**
+ * clo_func - Emulate a CLO instruction
+ * @regs: Process register set
+ * @ir: Instruction
+ *
+ * Returns 0 since it always succeeds.
+ */
+
+static int clo_func(struct pt_regs *regs, u32 ir)
+{
+	u32 res;
+	u32 rs;
+
+	if (!MIPSInst_RD(ir))
+		return 0;
+
+	rs = regs->regs[MIPSInst_RS(ir)];
+	__asm__ __volatile__("clo %0, %1" : "=r"(res) : "r"(rs));
+	regs->regs[MIPSInst_RD(ir)] = res;
+
+	MIPS_R2_STATS(bops);
+
+	return 0;
+}
+
+/**
+ * dclz_func - Emulate a DCLZ instruction
+ * @regs: Process register set
+ * @ir: Instruction
+ *
+ * Returns 0 since it always succeeds.
+ */
+static int dclz_func(struct pt_regs *regs, u32 ir)
+{
+	u64 res;
+	u64 rs;
+
+	if (IS_ENABLED(CONFIG_32BIT))
+		return SIGILL;
+
+	if (!MIPSInst_RD(ir))
+		return 0;
+
+	rs = regs->regs[MIPSInst_RS(ir)];
+	__asm__ __volatile__("dclz %0, %1" : "=r"(res) : "r"(rs));
+	regs->regs[MIPSInst_RD(ir)] = res;
+
+	MIPS_R2_STATS(bops);
+
+	return 0;
+}
+
+/**
+ * dclo_func - Emulate a DCLO instruction
+ * @regs: Process register set
+ * @ir: Instruction
+ *
+ * Returns 0 since it always succeeds.
+ */
+static int dclo_func(struct pt_regs *regs, u32 ir)
+{
+	u64 res;
+	u64 rs;
+
+	if (IS_ENABLED(CONFIG_32BIT))
+		return SIGILL;
+
+	if (!MIPSInst_RD(ir))
+		return 0;
+
+	rs = regs->regs[MIPSInst_RS(ir)];
+	__asm__ __volatile__("dclo %0, %1" : "=r"(res) : "r"(rs));
+	regs->regs[MIPSInst_RD(ir)] = res;
+
+	MIPS_R2_STATS(bops);
+
+	return 0;
+}
+
+/* R6 removed instructions for the SPECIAL2 opcode */
+static const struct r2_decoder_table spec2_op_table[] = {
+	{ 0xfc00ffff, 0x70000000, madd_func },
+	{ 0xfc00ffff, 0x70000001, maddu_func },
+	{ 0xfc0007ff, 0x70000002, mul_func },
+	{ 0xfc00ffff, 0x70000004, msub_func },
+	{ 0xfc00ffff, 0x70000005, msubu_func },
+	{ 0xfc0007ff, 0x70000020, clz_func },
+	{ 0xfc0007ff, 0x70000021, clo_func },
+	{ 0xfc0007ff, 0x70000024, dclz_func },
+	{ 0xfc0007ff, 0x70000025, dclo_func },
+	{ }
+};
+
+static inline int mipsr2_find_op_func(struct pt_regs *regs, u32 inst,
+				      const struct r2_decoder_table *table)
+{
+	const struct r2_decoder_table *p;
+	int err;
+
+	for (p = table; p->func; p++) {
+		if ((inst & p->mask) == p->code) {
+			err = (p->func)(regs, inst);
+			return err;
+		}
+	}
+	return SIGILL;
+}
+
+/**
+ * mipsr2_decoder: Decode and emulate a MIPS R2 instruction
+ * @regs: Process register set
+ * @inst: Instruction to decode and emulate
+ * @fcr31: Floating Point Control and Status Register Cause bits returned
+ */
+int mipsr2_decoder(struct pt_regs *regs, u32 inst, unsigned long *fcr31)
+{
+	int err = 0;
+	unsigned long vaddr;
+	u32 nir;
+	unsigned long cpc, epc, nepc, r31, res, rs, rt;
+
+	void __user *fault_addr = NULL;
+	int pass = 0;
+
+repeat:
+	r31 = regs->regs[31];
+	epc = regs->cp0_epc;
+	err = compute_return_epc(regs);
+	if (err < 0) {
+		BUG();
+		return SIGEMT;
+	}
+	pr_debug("Emulating the 0x%08x R2 instruction @ 0x%08lx (pass=%d))\n",
+		 inst, epc, pass);
+
+	switch (MIPSInst_OPCODE(inst)) {
+	case spec_op:
+		err = mipsr2_find_op_func(regs, inst, spec_op_table);
+		if (err < 0) {
+			/* FPU instruction under JR */
+			regs->cp0_cause |= CAUSEF_BD;
+			goto fpu_emul;
+		}
+		break;
+	case spec2_op:
+		err = mipsr2_find_op_func(regs, inst, spec2_op_table);
+		break;
+	case bcond_op:
+		rt = MIPSInst_RT(inst);
+		rs = MIPSInst_RS(inst);
+		switch (rt) {
+		case tgei_op:
+			if ((long)regs->regs[rs] >= MIPSInst_SIMM(inst))
+				do_trap_or_bp(regs, 0, 0, "TGEI");
+
+			MIPS_R2_STATS(traps);
+
+			break;
+		case tgeiu_op:
+			if (regs->regs[rs] >= MIPSInst_UIMM(inst))
+				do_trap_or_bp(regs, 0, 0, "TGEIU");
+
+			MIPS_R2_STATS(traps);
+
+			break;
+		case tlti_op:
+			if ((long)regs->regs[rs] < MIPSInst_SIMM(inst))
+				do_trap_or_bp(regs, 0, 0, "TLTI");
+
+			MIPS_R2_STATS(traps);
+
+			break;
+		case tltiu_op:
+			if (regs->regs[rs] < MIPSInst_UIMM(inst))
+				do_trap_or_bp(regs, 0, 0, "TLTIU");
+
+			MIPS_R2_STATS(traps);
+
+			break;
+		case teqi_op:
+			if (regs->regs[rs] == MIPSInst_SIMM(inst))
+				do_trap_or_bp(regs, 0, 0, "TEQI");
+
+			MIPS_R2_STATS(traps);
+
+			break;
+		case tnei_op:
+			if (regs->regs[rs] != MIPSInst_SIMM(inst))
+				do_trap_or_bp(regs, 0, 0, "TNEI");
+
+			MIPS_R2_STATS(traps);
+
+			break;
+		case bltzl_op:
+		case bgezl_op:
+		case bltzall_op:
+		case bgezall_op:
+			if (delay_slot(regs)) {
+				err = SIGILL;
+				break;
+			}
+			regs->regs[31] = r31;
+			regs->cp0_epc = epc;
+			err = __compute_return_epc(regs);
+			if (err < 0)
+				return SIGEMT;
+			if (err != BRANCH_LIKELY_TAKEN)
+				break;
+			cpc = regs->cp0_epc;
+			nepc = epc + 4;
+			err = __get_user(nir, (u32 __user *)nepc);
+			if (err) {
+				err = SIGSEGV;
+				break;
+			}
+			/*
+			 * This will probably be optimized away when
+			 * CONFIG_DEBUG_FS is not enabled
+			 */
+			switch (rt) {
+			case bltzl_op:
+				MIPS_R2BR_STATS(bltzl);
+				break;
+			case bgezl_op:
+				MIPS_R2BR_STATS(bgezl);
+				break;
+			case bltzall_op:
+				MIPS_R2BR_STATS(bltzall);
+				break;
+			case bgezall_op:
+				MIPS_R2BR_STATS(bgezall);
+				break;
+			}
+
+			switch (MIPSInst_OPCODE(nir)) {
+			case cop1_op:
+			case cop1x_op:
+			case lwc1_op:
+			case swc1_op:
+				regs->cp0_cause |= CAUSEF_BD;
+				goto fpu_emul;
+			}
+			if (nir) {
+				err = mipsr6_emul(regs, nir);
+				if (err > 0) {
+					err = mips_dsemul(regs, nir, epc, cpc);
+					if (err == SIGILL)
+						err = SIGEMT;
+					MIPS_R2_STATS(dsemul);
+				}
+			}
+			break;
+		case bltzal_op:
+		case bgezal_op:
+			if (delay_slot(regs)) {
+				err = SIGILL;
+				break;
+			}
+			regs->regs[31] = r31;
+			regs->cp0_epc = epc;
+			err = __compute_return_epc(regs);
+			if (err < 0)
+				return SIGEMT;
+			cpc = regs->cp0_epc;
+			nepc = epc + 4;
+			err = __get_user(nir, (u32 __user *)nepc);
+			if (err) {
+				err = SIGSEGV;
+				break;
+			}
+			/*
+			 * This will probably be optimized away when
+			 * CONFIG_DEBUG_FS is not enabled
+			 */
+			switch (rt) {
+			case bltzal_op:
+				MIPS_R2BR_STATS(bltzal);
+				break;
+			case bgezal_op:
+				MIPS_R2BR_STATS(bgezal);
+				break;
+			}
+
+			switch (MIPSInst_OPCODE(nir)) {
+			case cop1_op:
+			case cop1x_op:
+			case lwc1_op:
+			case swc1_op:
+				regs->cp0_cause |= CAUSEF_BD;
+				goto fpu_emul;
+			}
+			if (nir) {
+				err = mipsr6_emul(regs, nir);
+				if (err > 0) {
+					err = mips_dsemul(regs, nir, epc, cpc);
+					if (err == SIGILL)
+						err = SIGEMT;
+					MIPS_R2_STATS(dsemul);
+				}
+			}
+			break;
+		default:
+			regs->regs[31] = r31;
+			regs->cp0_epc = epc;
+			err = SIGILL;
+			break;
+		}
+		break;
+
+	case blezl_op:
+	case bgtzl_op:
+		/*
+		 * For BLEZL and BGTZL, rt field must be set to 0. If this
+		 * is not the case, this may be an encoding of a MIPS R6
+		 * instruction, so return to CPU execution if this occurs
+		 */
+		if (MIPSInst_RT(inst)) {
+			err = SIGILL;
+			break;
+		}
+		fallthrough;
+	case beql_op:
+	case bnel_op:
+		if (delay_slot(regs)) {
+			err = SIGILL;
+			break;
+		}
+		regs->regs[31] = r31;
+		regs->cp0_epc = epc;
+		err = __compute_return_epc(regs);
+		if (err < 0)
+			return SIGEMT;
+		if (err != BRANCH_LIKELY_TAKEN)
+			break;
+		cpc = regs->cp0_epc;
+		nepc = epc + 4;
+		err = __get_user(nir, (u32 __user *)nepc);
+		if (err) {
+			err = SIGSEGV;
+			break;
+		}
+		/*
+		 * This will probably be optimized away when
+		 * CONFIG_DEBUG_FS is not enabled
+		 */
+		switch (MIPSInst_OPCODE(inst)) {
+		case beql_op:
+			MIPS_R2BR_STATS(beql);
+			break;
+		case bnel_op:
+			MIPS_R2BR_STATS(bnel);
+			break;
+		case blezl_op:
+			MIPS_R2BR_STATS(blezl);
+			break;
+		case bgtzl_op:
+			MIPS_R2BR_STATS(bgtzl);
+			break;
+		}
+
+		switch (MIPSInst_OPCODE(nir)) {
+		case cop1_op:
+		case cop1x_op:
+		case lwc1_op:
+		case swc1_op:
+			regs->cp0_cause |= CAUSEF_BD;
+			goto fpu_emul;
+		}
+		if (nir) {
+			err = mipsr6_emul(regs, nir);
+			if (err > 0) {
+				err = mips_dsemul(regs, nir, epc, cpc);
+				if (err == SIGILL)
+					err = SIGEMT;
+				MIPS_R2_STATS(dsemul);
+			}
+		}
+		break;
+	case lwc1_op:
+	case swc1_op:
+	case cop1_op:
+	case cop1x_op:
+fpu_emul:
+		regs->regs[31] = r31;
+		regs->cp0_epc = epc;
+
+		err = fpu_emulator_cop1Handler(regs, &current->thread.fpu, 0,
+					       &fault_addr);
+
+		/*
+		 * We can't allow the emulated instruction to leave any
+		 * enabled Cause bits set in $fcr31.
+		 */
+		*fcr31 = res = mask_fcr31_x(current->thread.fpu.fcr31);
+		current->thread.fpu.fcr31 &= ~res;
+
+		/*
+		 * this is a tricky issue - lose_fpu() uses LL/SC atomics
+		 * if FPU is owned and effectively cancels user level LL/SC.
+		 * So, it could be logical to don't restore FPU ownership here.
+		 * But the sequence of multiple FPU instructions is much much
+		 * more often than LL-FPU-SC and I prefer loop here until
+		 * next scheduler cycle cancels FPU ownership
+		 */
+		own_fpu(1);	/* Restore FPU state. */
+
+		if (err)
+			current->thread.cp0_baduaddr = (unsigned long)fault_addr;
+
+		MIPS_R2_STATS(fpus);
+
+		break;
+
+	case lwl_op:
+		rt = regs->regs[MIPSInst_RT(inst)];
+		vaddr = regs->regs[MIPSInst_RS(inst)] + MIPSInst_SIMM(inst);
+		if (!access_ok((void __user *)vaddr, 4)) {
+			current->thread.cp0_baduaddr = vaddr;
+			err = SIGSEGV;
+			break;
+		}
+		__asm__ __volatile__(
+			"	.set	push\n"
+			"	.set	reorder\n"
+#ifdef CONFIG_CPU_LITTLE_ENDIAN
+			"1:"	LB	"%1, 0(%2)\n"
+				INS	"%0, %1, 24, 8\n"
+			"	andi	%1, %2, 0x3\n"
+			"	beq	$0, %1, 9f\n"
+				ADDIU	"%2, %2, -1\n"
+			"2:"	LB	"%1, 0(%2)\n"
+				INS	"%0, %1, 16, 8\n"
+			"	andi	%1, %2, 0x3\n"
+			"	beq	$0, %1, 9f\n"
+				ADDIU	"%2, %2, -1\n"
+			"3:"	LB	"%1, 0(%2)\n"
+				INS	"%0, %1, 8, 8\n"
+			"	andi	%1, %2, 0x3\n"
+			"	beq	$0, %1, 9f\n"
+				ADDIU	"%2, %2, -1\n"
+			"4:"	LB	"%1, 0(%2)\n"
+				INS	"%0, %1, 0, 8\n"
+#else /* !CONFIG_CPU_LITTLE_ENDIAN */
+			"1:"	LB	"%1, 0(%2)\n"
+				INS	"%0, %1, 24, 8\n"
+				ADDIU	"%2, %2, 1\n"
+			"	andi	%1, %2, 0x3\n"
+			"	beq	$0, %1, 9f\n"
+			"2:"	LB	"%1, 0(%2)\n"
+				INS	"%0, %1, 16, 8\n"
+				ADDIU	"%2, %2, 1\n"
+			"	andi	%1, %2, 0x3\n"
+			"	beq	$0, %1, 9f\n"
+			"3:"	LB	"%1, 0(%2)\n"
+				INS	"%0, %1, 8, 8\n"
+				ADDIU	"%2, %2, 1\n"
+			"	andi	%1, %2, 0x3\n"
+			"	beq	$0, %1, 9f\n"
+			"4:"	LB	"%1, 0(%2)\n"
+				INS	"%0, %1, 0, 8\n"
+#endif /* CONFIG_CPU_LITTLE_ENDIAN */
+			"9:	sll	%0, %0, 0\n"
+			"10:\n"
+			"	.insn\n"
+			"	.section	.fixup,\"ax\"\n"
+			"8:	li	%3,%4\n"
+			"	j	10b\n"
+			"	.previous\n"
+			"	.section	__ex_table,\"a\"\n"
+			STR(PTR_WD) " 1b,8b\n"
+			STR(PTR_WD) " 2b,8b\n"
+			STR(PTR_WD) " 3b,8b\n"
+			STR(PTR_WD) " 4b,8b\n"
+			"	.previous\n"
+			"	.set	pop\n"
+			: "+&r"(rt), "=&r"(rs),
+			  "+&r"(vaddr), "+&r"(err)
+			: "i"(SIGSEGV));
+
+		if (MIPSInst_RT(inst) && !err)
+			regs->regs[MIPSInst_RT(inst)] = rt;
+
+		MIPS_R2_STATS(loads);
+
+		break;
+
+	case lwr_op:
+		rt = regs->regs[MIPSInst_RT(inst)];
+		vaddr = regs->regs[MIPSInst_RS(inst)] + MIPSInst_SIMM(inst);
+		if (!access_ok((void __user *)vaddr, 4)) {
+			current->thread.cp0_baduaddr = vaddr;
+			err = SIGSEGV;
+			break;
+		}
+		__asm__ __volatile__(
+			"       .set	push\n"
+			"       .set	reorder\n"
+#ifdef CONFIG_CPU_LITTLE_ENDIAN
+			"1:"    LB	"%1, 0(%2)\n"
+				INS	"%0, %1, 0, 8\n"
+				ADDIU	"%2, %2, 1\n"
+			"       andi	%1, %2, 0x3\n"
+			"       beq	$0, %1, 9f\n"
+			"2:"    LB	"%1, 0(%2)\n"
+				INS	"%0, %1, 8, 8\n"
+				ADDIU	"%2, %2, 1\n"
+			"       andi	%1, %2, 0x3\n"
+			"       beq	$0, %1, 9f\n"
+			"3:"    LB	"%1, 0(%2)\n"
+				INS	"%0, %1, 16, 8\n"
+				ADDIU	"%2, %2, 1\n"
+			"       andi	%1, %2, 0x3\n"
+			"       beq	$0, %1, 9f\n"
+			"4:"    LB	"%1, 0(%2)\n"
+				INS	"%0, %1, 24, 8\n"
+			"       sll	%0, %0, 0\n"
+#else /* !CONFIG_CPU_LITTLE_ENDIAN */
+			"1:"    LB	"%1, 0(%2)\n"
+				INS	"%0, %1, 0, 8\n"
+			"       andi	%1, %2, 0x3\n"
+			"       beq	$0, %1, 9f\n"
+				ADDIU	"%2, %2, -1\n"
+			"2:"    LB	"%1, 0(%2)\n"
+				INS	"%0, %1, 8, 8\n"
+			"       andi	%1, %2, 0x3\n"
+			"       beq	$0, %1, 9f\n"
+				ADDIU	"%2, %2, -1\n"
+			"3:"    LB	"%1, 0(%2)\n"
+				INS	"%0, %1, 16, 8\n"
+			"       andi	%1, %2, 0x3\n"
+			"       beq	$0, %1, 9f\n"
+				ADDIU	"%2, %2, -1\n"
+			"4:"    LB	"%1, 0(%2)\n"
+				INS	"%0, %1, 24, 8\n"
+			"       sll	%0, %0, 0\n"
+#endif /* CONFIG_CPU_LITTLE_ENDIAN */
+			"9:\n"
+			"10:\n"
+			"	.insn\n"
+			"	.section	.fixup,\"ax\"\n"
+			"8:	li	%3,%4\n"
+			"	j	10b\n"
+			"       .previous\n"
+			"	.section	__ex_table,\"a\"\n"
+			STR(PTR_WD) " 1b,8b\n"
+			STR(PTR_WD) " 2b,8b\n"
+			STR(PTR_WD) " 3b,8b\n"
+			STR(PTR_WD) " 4b,8b\n"
+			"	.previous\n"
+			"	.set	pop\n"
+			: "+&r"(rt), "=&r"(rs),
+			  "+&r"(vaddr), "+&r"(err)
+			: "i"(SIGSEGV));
+		if (MIPSInst_RT(inst) && !err)
+			regs->regs[MIPSInst_RT(inst)] = rt;
+
+		MIPS_R2_STATS(loads);
+
+		break;
+
+	case swl_op:
+		rt = regs->regs[MIPSInst_RT(inst)];
+		vaddr = regs->regs[MIPSInst_RS(inst)] + MIPSInst_SIMM(inst);
+		if (!access_ok((void __user *)vaddr, 4)) {
+			current->thread.cp0_baduaddr = vaddr;
+			err = SIGSEGV;
+			break;
+		}
+		__asm__ __volatile__(
+			"	.set	push\n"
+			"	.set	reorder\n"
+#ifdef CONFIG_CPU_LITTLE_ENDIAN
+				EXT	"%1, %0, 24, 8\n"
+			"1:"	SB	"%1, 0(%2)\n"
+			"	andi	%1, %2, 0x3\n"
+			"	beq	$0, %1, 9f\n"
+				ADDIU	"%2, %2, -1\n"
+				EXT	"%1, %0, 16, 8\n"
+			"2:"	SB	"%1, 0(%2)\n"
+			"	andi	%1, %2, 0x3\n"
+			"	beq	$0, %1, 9f\n"
+				ADDIU	"%2, %2, -1\n"
+				EXT	"%1, %0, 8, 8\n"
+			"3:"	SB	"%1, 0(%2)\n"
+			"	andi	%1, %2, 0x3\n"
+			"	beq	$0, %1, 9f\n"
+				ADDIU	"%2, %2, -1\n"
+				EXT	"%1, %0, 0, 8\n"
+			"4:"	SB	"%1, 0(%2)\n"
+#else /* !CONFIG_CPU_LITTLE_ENDIAN */
+				EXT	"%1, %0, 24, 8\n"
+			"1:"	SB	"%1, 0(%2)\n"
+				ADDIU	"%2, %2, 1\n"
+			"	andi	%1, %2, 0x3\n"
+			"	beq	$0, %1, 9f\n"
+				EXT	"%1, %0, 16, 8\n"
+			"2:"	SB	"%1, 0(%2)\n"
+				ADDIU	"%2, %2, 1\n"
+			"	andi	%1, %2, 0x3\n"
+			"	beq	$0, %1, 9f\n"
+				EXT	"%1, %0, 8, 8\n"
+			"3:"	SB	"%1, 0(%2)\n"
+				ADDIU	"%2, %2, 1\n"
+			"	andi	%1, %2, 0x3\n"
+			"	beq	$0, %1, 9f\n"
+				EXT	"%1, %0, 0, 8\n"
+			"4:"	SB	"%1, 0(%2)\n"
+#endif /* CONFIG_CPU_LITTLE_ENDIAN */
+			"9:\n"
+			"	.insn\n"
+			"       .section        .fixup,\"ax\"\n"
+			"8:	li	%3,%4\n"
+			"	j	9b\n"
+			"	.previous\n"
+			"	.section        __ex_table,\"a\"\n"
+			STR(PTR_WD) " 1b,8b\n"
+			STR(PTR_WD) " 2b,8b\n"
+			STR(PTR_WD) " 3b,8b\n"
+			STR(PTR_WD) " 4b,8b\n"
+			"	.previous\n"
+			"	.set	pop\n"
+			: "+&r"(rt), "=&r"(rs),
+			  "+&r"(vaddr), "+&r"(err)
+			: "i"(SIGSEGV)
+			: "memory");
+
+		MIPS_R2_STATS(stores);
+
+		break;
+
+	case swr_op:
+		rt = regs->regs[MIPSInst_RT(inst)];
+		vaddr = regs->regs[MIPSInst_RS(inst)] + MIPSInst_SIMM(inst);
+		if (!access_ok((void __user *)vaddr, 4)) {
+			current->thread.cp0_baduaddr = vaddr;
+			err = SIGSEGV;
+			break;
+		}
+		__asm__ __volatile__(
+			"	.set	push\n"
+			"	.set	reorder\n"
+#ifdef CONFIG_CPU_LITTLE_ENDIAN
+				EXT	"%1, %0, 0, 8\n"
+			"1:"	SB	"%1, 0(%2)\n"
+				ADDIU	"%2, %2, 1\n"
+			"	andi	%1, %2, 0x3\n"
+			"	beq	$0, %1, 9f\n"
+				EXT	"%1, %0, 8, 8\n"
+			"2:"	SB	"%1, 0(%2)\n"
+				ADDIU	"%2, %2, 1\n"
+			"	andi	%1, %2, 0x3\n"
+			"	beq	$0, %1, 9f\n"
+				EXT	"%1, %0, 16, 8\n"
+			"3:"	SB	"%1, 0(%2)\n"
+				ADDIU	"%2, %2, 1\n"
+			"	andi	%1, %2, 0x3\n"
+			"	beq	$0, %1, 9f\n"
+				EXT	"%1, %0, 24, 8\n"
+			"4:"	SB	"%1, 0(%2)\n"
+#else /* !CONFIG_CPU_LITTLE_ENDIAN */
+				EXT	"%1, %0, 0, 8\n"
+			"1:"	SB	"%1, 0(%2)\n"
+			"	andi	%1, %2, 0x3\n"
+			"	beq	$0, %1, 9f\n"
+				ADDIU	"%2, %2, -1\n"
+				EXT	"%1, %0, 8, 8\n"
+			"2:"	SB	"%1, 0(%2)\n"
+			"	andi	%1, %2, 0x3\n"
+			"	beq	$0, %1, 9f\n"
+				ADDIU	"%2, %2, -1\n"
+				EXT	"%1, %0, 16, 8\n"
+			"3:"	SB	"%1, 0(%2)\n"
+			"	andi	%1, %2, 0x3\n"
+			"	beq	$0, %1, 9f\n"
+				ADDIU	"%2, %2, -1\n"
+				EXT	"%1, %0, 24, 8\n"
+			"4:"	SB	"%1, 0(%2)\n"
+#endif /* CONFIG_CPU_LITTLE_ENDIAN */
+			"9:\n"
+			"	.insn\n"
+			"	.section        .fixup,\"ax\"\n"
+			"8:	li	%3,%4\n"
+			"	j	9b\n"
+			"	.previous\n"
+			"	.section        __ex_table,\"a\"\n"
+			STR(PTR_WD) " 1b,8b\n"
+			STR(PTR_WD) " 2b,8b\n"
+			STR(PTR_WD) " 3b,8b\n"
+			STR(PTR_WD) " 4b,8b\n"
+			"	.previous\n"
+			"	.set	pop\n"
+			: "+&r"(rt), "=&r"(rs),
+			  "+&r"(vaddr), "+&r"(err)
+			: "i"(SIGSEGV)
+			: "memory");
+
+		MIPS_R2_STATS(stores);
+
+		break;
+
+	case ldl_op:
+		if (IS_ENABLED(CONFIG_32BIT)) {
+		    err = SIGILL;
+		    break;
+		}
+
+		rt = regs->regs[MIPSInst_RT(inst)];
+		vaddr = regs->regs[MIPSInst_RS(inst)] + MIPSInst_SIMM(inst);
+		if (!access_ok((void __user *)vaddr, 8)) {
+			current->thread.cp0_baduaddr = vaddr;
+			err = SIGSEGV;
+			break;
+		}
+		__asm__ __volatile__(
+			"	.set    push\n"
+			"	.set    reorder\n"
+#ifdef CONFIG_CPU_LITTLE_ENDIAN
+			"1:	lb	%1, 0(%2)\n"
+			"	dinsu	%0, %1, 56, 8\n"
+			"	andi	%1, %2, 0x7\n"
+			"	beq	$0, %1, 9f\n"
+			"	daddiu	%2, %2, -1\n"
+			"2:	lb	%1, 0(%2)\n"
+			"	dinsu	%0, %1, 48, 8\n"
+			"	andi	%1, %2, 0x7\n"
+			"	beq	$0, %1, 9f\n"
+			"	daddiu	%2, %2, -1\n"
+			"3:	lb	%1, 0(%2)\n"
+			"	dinsu	%0, %1, 40, 8\n"
+			"	andi	%1, %2, 0x7\n"
+			"	beq	$0, %1, 9f\n"
+			"	daddiu	%2, %2, -1\n"
+			"4:	lb	%1, 0(%2)\n"
+			"	dinsu	%0, %1, 32, 8\n"
+			"	andi	%1, %2, 0x7\n"
+			"	beq	$0, %1, 9f\n"
+			"	daddiu	%2, %2, -1\n"
+			"5:	lb	%1, 0(%2)\n"
+			"	dins	%0, %1, 24, 8\n"
+			"	andi	%1, %2, 0x7\n"
+			"	beq	$0, %1, 9f\n"
+			"	daddiu	%2, %2, -1\n"
+			"6:	lb	%1, 0(%2)\n"
+			"	dins	%0, %1, 16, 8\n"
+			"	andi	%1, %2, 0x7\n"
+			"	beq	$0, %1, 9f\n"
+			"	daddiu	%2, %2, -1\n"
+			"7:	lb	%1, 0(%2)\n"
+			"	dins	%0, %1, 8, 8\n"
+			"	andi	%1, %2, 0x7\n"
+			"	beq	$0, %1, 9f\n"
+			"	daddiu	%2, %2, -1\n"
+			"0:	lb	%1, 0(%2)\n"
+			"	dins	%0, %1, 0, 8\n"
+#else /* !CONFIG_CPU_LITTLE_ENDIAN */
+			"1:	lb	%1, 0(%2)\n"
+			"	dinsu	%0, %1, 56, 8\n"
+			"	daddiu	%2, %2, 1\n"
+			"	andi	%1, %2, 0x7\n"
+			"	beq	$0, %1, 9f\n"
+			"2:	lb	%1, 0(%2)\n"
+			"	dinsu	%0, %1, 48, 8\n"
+			"	daddiu	%2, %2, 1\n"
+			"	andi	%1, %2, 0x7\n"
+			"	beq	$0, %1, 9f\n"
+			"3:	lb	%1, 0(%2)\n"
+			"	dinsu	%0, %1, 40, 8\n"
+			"	daddiu  %2, %2, 1\n"
+			"	andi	%1, %2, 0x7\n"
+			"	beq	$0, %1, 9f\n"
+			"4:	lb	%1, 0(%2)\n"
+			"	dinsu	%0, %1, 32, 8\n"
+			"	daddiu	%2, %2, 1\n"
+			"	andi	%1, %2, 0x7\n"
+			"	beq	$0, %1, 9f\n"
+			"5:	lb	%1, 0(%2)\n"
+			"	dins	%0, %1, 24, 8\n"
+			"	daddiu	%2, %2, 1\n"
+			"	andi	%1, %2, 0x7\n"
+			"	beq	$0, %1, 9f\n"
+			"6:	lb	%1, 0(%2)\n"
+			"	dins	%0, %1, 16, 8\n"
+			"	daddiu	%2, %2, 1\n"
+			"	andi	%1, %2, 0x7\n"
+			"	beq	$0, %1, 9f\n"
+			"7:	lb	%1, 0(%2)\n"
+			"	dins	%0, %1, 8, 8\n"
+			"	daddiu	%2, %2, 1\n"
+			"	andi	%1, %2, 0x7\n"
+			"	beq	$0, %1, 9f\n"
+			"0:	lb	%1, 0(%2)\n"
+			"	dins	%0, %1, 0, 8\n"
+#endif /* CONFIG_CPU_LITTLE_ENDIAN */
+			"9:\n"
+			"	.insn\n"
+			"	.section        .fixup,\"ax\"\n"
+			"8:	li	%3,%4\n"
+			"	j	9b\n"
+			"	.previous\n"
+			"	.section        __ex_table,\"a\"\n"
+			STR(PTR_WD) " 1b,8b\n"
+			STR(PTR_WD) " 2b,8b\n"
+			STR(PTR_WD) " 3b,8b\n"
+			STR(PTR_WD) " 4b,8b\n"
+			STR(PTR_WD) " 5b,8b\n"
+			STR(PTR_WD) " 6b,8b\n"
+			STR(PTR_WD) " 7b,8b\n"
+			STR(PTR_WD) " 0b,8b\n"
+			"	.previous\n"
+			"	.set	pop\n"
+			: "+&r"(rt), "=&r"(rs),
+			  "+&r"(vaddr), "+&r"(err)
+			: "i"(SIGSEGV));
+		if (MIPSInst_RT(inst) && !err)
+			regs->regs[MIPSInst_RT(inst)] = rt;
+
+		MIPS_R2_STATS(loads);
+		break;
+
+	case ldr_op:
+		if (IS_ENABLED(CONFIG_32BIT)) {
+		    err = SIGILL;
+		    break;
+		}
+
+		rt = regs->regs[MIPSInst_RT(inst)];
+		vaddr = regs->regs[MIPSInst_RS(inst)] + MIPSInst_SIMM(inst);
+		if (!access_ok((void __user *)vaddr, 8)) {
+			current->thread.cp0_baduaddr = vaddr;
+			err = SIGSEGV;
+			break;
+		}
+		__asm__ __volatile__(
+			"	.set    push\n"
+			"	.set    reorder\n"
+#ifdef CONFIG_CPU_LITTLE_ENDIAN
+			"1:	lb      %1, 0(%2)\n"
+			"	dins   %0, %1, 0, 8\n"
+			"	daddiu  %2, %2, 1\n"
+			"	andi    %1, %2, 0x7\n"
+			"	beq     $0, %1, 9f\n"
+			"2:	lb      %1, 0(%2)\n"
+			"	dins   %0, %1, 8, 8\n"
+			"	daddiu  %2, %2, 1\n"
+			"	andi    %1, %2, 0x7\n"
+			"	beq     $0, %1, 9f\n"
+			"3:	lb      %1, 0(%2)\n"
+			"	dins   %0, %1, 16, 8\n"
+			"	daddiu  %2, %2, 1\n"
+			"	andi    %1, %2, 0x7\n"
+			"	beq     $0, %1, 9f\n"
+			"4:	lb      %1, 0(%2)\n"
+			"	dins   %0, %1, 24, 8\n"
+			"	daddiu  %2, %2, 1\n"
+			"	andi    %1, %2, 0x7\n"
+			"	beq     $0, %1, 9f\n"
+			"5:	lb      %1, 0(%2)\n"
+			"	dinsu    %0, %1, 32, 8\n"
+			"	daddiu  %2, %2, 1\n"
+			"	andi    %1, %2, 0x7\n"
+			"	beq     $0, %1, 9f\n"
+			"6:	lb      %1, 0(%2)\n"
+			"	dinsu    %0, %1, 40, 8\n"
+			"	daddiu  %2, %2, 1\n"
+			"	andi    %1, %2, 0x7\n"
+			"	beq     $0, %1, 9f\n"
+			"7:	lb      %1, 0(%2)\n"
+			"	dinsu    %0, %1, 48, 8\n"
+			"	daddiu  %2, %2, 1\n"
+			"	andi    %1, %2, 0x7\n"
+			"	beq     $0, %1, 9f\n"
+			"0:	lb      %1, 0(%2)\n"
+			"	dinsu    %0, %1, 56, 8\n"
+#else /* !CONFIG_CPU_LITTLE_ENDIAN */
+			"1:	lb      %1, 0(%2)\n"
+			"	dins   %0, %1, 0, 8\n"
+			"	andi    %1, %2, 0x7\n"
+			"	beq     $0, %1, 9f\n"
+			"	daddiu  %2, %2, -1\n"
+			"2:	lb      %1, 0(%2)\n"
+			"	dins   %0, %1, 8, 8\n"
+			"	andi    %1, %2, 0x7\n"
+			"	beq     $0, %1, 9f\n"
+			"	daddiu  %2, %2, -1\n"
+			"3:	lb      %1, 0(%2)\n"
+			"	dins   %0, %1, 16, 8\n"
+			"	andi    %1, %2, 0x7\n"
+			"	beq     $0, %1, 9f\n"
+			"	daddiu  %2, %2, -1\n"
+			"4:	lb      %1, 0(%2)\n"
+			"	dins   %0, %1, 24, 8\n"
+			"	andi    %1, %2, 0x7\n"
+			"	beq     $0, %1, 9f\n"
+			"	daddiu  %2, %2, -1\n"
+			"5:	lb      %1, 0(%2)\n"
+			"	dinsu    %0, %1, 32, 8\n"
+			"	andi    %1, %2, 0x7\n"
+			"	beq     $0, %1, 9f\n"
+			"	daddiu  %2, %2, -1\n"
+			"6:	lb      %1, 0(%2)\n"
+			"	dinsu    %0, %1, 40, 8\n"
+			"	andi    %1, %2, 0x7\n"
+			"	beq     $0, %1, 9f\n"
+			"	daddiu  %2, %2, -1\n"
+			"7:	lb      %1, 0(%2)\n"
+			"	dinsu    %0, %1, 48, 8\n"
+			"	andi    %1, %2, 0x7\n"
+			"	beq     $0, %1, 9f\n"
+			"	daddiu  %2, %2, -1\n"
+			"0:	lb      %1, 0(%2)\n"
+			"	dinsu    %0, %1, 56, 8\n"
+#endif /* CONFIG_CPU_LITTLE_ENDIAN */
+			"9:\n"
+			"	.insn\n"
+			"	.section        .fixup,\"ax\"\n"
+			"8:	li     %3,%4\n"
+			"	j      9b\n"
+			"	.previous\n"
+			"	.section        __ex_table,\"a\"\n"
+			STR(PTR_WD) " 1b,8b\n"
+			STR(PTR_WD) " 2b,8b\n"
+			STR(PTR_WD) " 3b,8b\n"
+			STR(PTR_WD) " 4b,8b\n"
+			STR(PTR_WD) " 5b,8b\n"
+			STR(PTR_WD) " 6b,8b\n"
+			STR(PTR_WD) " 7b,8b\n"
+			STR(PTR_WD) " 0b,8b\n"
+			"	.previous\n"
+			"	.set    pop\n"
+			: "+&r"(rt), "=&r"(rs),
+			  "+&r"(vaddr), "+&r"(err)
+			: "i"(SIGSEGV));
+		if (MIPSInst_RT(inst) && !err)
+			regs->regs[MIPSInst_RT(inst)] = rt;
+
+		MIPS_R2_STATS(loads);
+		break;
+
+	case sdl_op:
+		if (IS_ENABLED(CONFIG_32BIT)) {
+		    err = SIGILL;
+		    break;
+		}
+
+		rt = regs->regs[MIPSInst_RT(inst)];
+		vaddr = regs->regs[MIPSInst_RS(inst)] + MIPSInst_SIMM(inst);
+		if (!access_ok((void __user *)vaddr, 8)) {
+			current->thread.cp0_baduaddr = vaddr;
+			err = SIGSEGV;
+			break;
+		}
+		__asm__ __volatile__(
+			"	.set	push\n"
+			"	.set	reorder\n"
+#ifdef CONFIG_CPU_LITTLE_ENDIAN
+			"	dextu	%1, %0, 56, 8\n"
+			"1:	sb	%1, 0(%2)\n"
+			"	andi	%1, %2, 0x7\n"
+			"	beq	$0, %1, 9f\n"
+			"	daddiu	%2, %2, -1\n"
+			"	dextu	%1, %0, 48, 8\n"
+			"2:	sb	%1, 0(%2)\n"
+			"	andi	%1, %2, 0x7\n"
+			"	beq	$0, %1, 9f\n"
+			"	daddiu	%2, %2, -1\n"
+			"	dextu	%1, %0, 40, 8\n"
+			"3:	sb	%1, 0(%2)\n"
+			"	andi	%1, %2, 0x7\n"
+			"	beq	$0, %1, 9f\n"
+			"	daddiu	%2, %2, -1\n"
+			"	dextu	%1, %0, 32, 8\n"
+			"4:	sb	%1, 0(%2)\n"
+			"	andi	%1, %2, 0x7\n"
+			"	beq	$0, %1, 9f\n"
+			"	daddiu	%2, %2, -1\n"
+			"	dext	%1, %0, 24, 8\n"
+			"5:	sb	%1, 0(%2)\n"
+			"	andi	%1, %2, 0x7\n"
+			"	beq	$0, %1, 9f\n"
+			"	daddiu	%2, %2, -1\n"
+			"	dext	%1, %0, 16, 8\n"
+			"6:	sb	%1, 0(%2)\n"
+			"	andi	%1, %2, 0x7\n"
+			"	beq	$0, %1, 9f\n"
+			"	daddiu	%2, %2, -1\n"
+			"	dext	%1, %0, 8, 8\n"
+			"7:	sb	%1, 0(%2)\n"
+			"	andi	%1, %2, 0x7\n"
+			"	beq	$0, %1, 9f\n"
+			"	daddiu	%2, %2, -1\n"
+			"	dext	%1, %0, 0, 8\n"
+			"0:	sb	%1, 0(%2)\n"
+#else /* !CONFIG_CPU_LITTLE_ENDIAN */
+			"	dextu	%1, %0, 56, 8\n"
+			"1:	sb	%1, 0(%2)\n"
+			"	daddiu	%2, %2, 1\n"
+			"	andi	%1, %2, 0x7\n"
+			"	beq	$0, %1, 9f\n"
+			"	dextu	%1, %0, 48, 8\n"
+			"2:	sb	%1, 0(%2)\n"
+			"	daddiu	%2, %2, 1\n"
+			"	andi	%1, %2, 0x7\n"
+			"	beq	$0, %1, 9f\n"
+			"	dextu	%1, %0, 40, 8\n"
+			"3:	sb	%1, 0(%2)\n"
+			"	daddiu	%2, %2, 1\n"
+			"	andi	%1, %2, 0x7\n"
+			"	beq	$0, %1, 9f\n"
+			"	dextu	%1, %0, 32, 8\n"
+			"4:	sb	%1, 0(%2)\n"
+			"	daddiu	%2, %2, 1\n"
+			"	andi	%1, %2, 0x7\n"
+			"	beq	$0, %1, 9f\n"
+			"	dext	%1, %0, 24, 8\n"
+			"5:	sb	%1, 0(%2)\n"
+			"	daddiu	%2, %2, 1\n"
+			"	andi	%1, %2, 0x7\n"
+			"	beq	$0, %1, 9f\n"
+			"	dext	%1, %0, 16, 8\n"
+			"6:	sb	%1, 0(%2)\n"
+			"	daddiu	%2, %2, 1\n"
+			"	andi	%1, %2, 0x7\n"
+			"	beq	$0, %1, 9f\n"
+			"	dext	%1, %0, 8, 8\n"
+			"7:	sb	%1, 0(%2)\n"
+			"	daddiu	%2, %2, 1\n"
+			"	andi	%1, %2, 0x7\n"
+			"	beq	$0, %1, 9f\n"
+			"	dext	%1, %0, 0, 8\n"
+			"0:	sb	%1, 0(%2)\n"
+#endif /* CONFIG_CPU_LITTLE_ENDIAN */
+			"9:\n"
+			"	.insn\n"
+			"	.section        .fixup,\"ax\"\n"
+			"8:	li	%3,%4\n"
+			"	j	9b\n"
+			"	.previous\n"
+			"	.section        __ex_table,\"a\"\n"
+			STR(PTR_WD) " 1b,8b\n"
+			STR(PTR_WD) " 2b,8b\n"
+			STR(PTR_WD) " 3b,8b\n"
+			STR(PTR_WD) " 4b,8b\n"
+			STR(PTR_WD) " 5b,8b\n"
+			STR(PTR_WD) " 6b,8b\n"
+			STR(PTR_WD) " 7b,8b\n"
+			STR(PTR_WD) " 0b,8b\n"
+			"	.previous\n"
+			"	.set	pop\n"
+			: "+&r"(rt), "=&r"(rs),
+			  "+&r"(vaddr), "+&r"(err)
+			: "i"(SIGSEGV)
+			: "memory");
+
+		MIPS_R2_STATS(stores);
+		break;
+
+	case sdr_op:
+		if (IS_ENABLED(CONFIG_32BIT)) {
+		    err = SIGILL;
+		    break;
+		}
+
+		rt = regs->regs[MIPSInst_RT(inst)];
+		vaddr = regs->regs[MIPSInst_RS(inst)] + MIPSInst_SIMM(inst);
+		if (!access_ok((void __user *)vaddr, 8)) {
+			current->thread.cp0_baduaddr = vaddr;
+			err = SIGSEGV;
+			break;
+		}
+		__asm__ __volatile__(
+			"       .set	push\n"
+			"       .set	reorder\n"
+#ifdef CONFIG_CPU_LITTLE_ENDIAN
+			"       dext	%1, %0, 0, 8\n"
+			"1:     sb	%1, 0(%2)\n"
+			"       daddiu	%2, %2, 1\n"
+			"       andi	%1, %2, 0x7\n"
+			"       beq	$0, %1, 9f\n"
+			"       dext	%1, %0, 8, 8\n"
+			"2:     sb	%1, 0(%2)\n"
+			"       daddiu	%2, %2, 1\n"
+			"       andi	%1, %2, 0x7\n"
+			"       beq	$0, %1, 9f\n"
+			"       dext	%1, %0, 16, 8\n"
+			"3:     sb	%1, 0(%2)\n"
+			"       daddiu	%2, %2, 1\n"
+			"       andi	%1, %2, 0x7\n"
+			"       beq	$0, %1, 9f\n"
+			"       dext	%1, %0, 24, 8\n"
+			"4:     sb	%1, 0(%2)\n"
+			"       daddiu	%2, %2, 1\n"
+			"       andi	%1, %2, 0x7\n"
+			"       beq	$0, %1, 9f\n"
+			"       dextu	%1, %0, 32, 8\n"
+			"5:     sb	%1, 0(%2)\n"
+			"       daddiu	%2, %2, 1\n"
+			"       andi	%1, %2, 0x7\n"
+			"       beq	$0, %1, 9f\n"
+			"       dextu	%1, %0, 40, 8\n"
+			"6:     sb	%1, 0(%2)\n"
+			"       daddiu	%2, %2, 1\n"
+			"       andi	%1, %2, 0x7\n"
+			"       beq	$0, %1, 9f\n"
+			"       dextu	%1, %0, 48, 8\n"
+			"7:     sb	%1, 0(%2)\n"
+			"       daddiu	%2, %2, 1\n"
+			"       andi	%1, %2, 0x7\n"
+			"       beq	$0, %1, 9f\n"
+			"       dextu	%1, %0, 56, 8\n"
+			"0:     sb	%1, 0(%2)\n"
+#else /* !CONFIG_CPU_LITTLE_ENDIAN */
+			"       dext	%1, %0, 0, 8\n"
+			"1:     sb	%1, 0(%2)\n"
+			"       andi	%1, %2, 0x7\n"
+			"       beq	$0, %1, 9f\n"
+			"       daddiu	%2, %2, -1\n"
+			"       dext	%1, %0, 8, 8\n"
+			"2:     sb	%1, 0(%2)\n"
+			"       andi	%1, %2, 0x7\n"
+			"       beq	$0, %1, 9f\n"
+			"       daddiu	%2, %2, -1\n"
+			"       dext	%1, %0, 16, 8\n"
+			"3:     sb	%1, 0(%2)\n"
+			"       andi	%1, %2, 0x7\n"
+			"       beq	$0, %1, 9f\n"
+			"       daddiu	%2, %2, -1\n"
+			"       dext	%1, %0, 24, 8\n"
+			"4:     sb	%1, 0(%2)\n"
+			"       andi	%1, %2, 0x7\n"
+			"       beq	$0, %1, 9f\n"
+			"       daddiu	%2, %2, -1\n"
+			"       dextu	%1, %0, 32, 8\n"
+			"5:     sb	%1, 0(%2)\n"
+			"       andi	%1, %2, 0x7\n"
+			"       beq	$0, %1, 9f\n"
+			"       daddiu	%2, %2, -1\n"
+			"       dextu	%1, %0, 40, 8\n"
+			"6:     sb	%1, 0(%2)\n"
+			"       andi	%1, %2, 0x7\n"
+			"       beq	$0, %1, 9f\n"
+			"       daddiu	%2, %2, -1\n"
+			"       dextu	%1, %0, 48, 8\n"
+			"7:     sb	%1, 0(%2)\n"
+			"       andi	%1, %2, 0x7\n"
+			"       beq	$0, %1, 9f\n"
+			"       daddiu	%2, %2, -1\n"
+			"       dextu	%1, %0, 56, 8\n"
+			"0:     sb	%1, 0(%2)\n"
+#endif /* CONFIG_CPU_LITTLE_ENDIAN */
+			"9:\n"
+			"       .insn\n"
+			"       .section        .fixup,\"ax\"\n"
+			"8:     li	%3,%4\n"
+			"       j	9b\n"
+			"       .previous\n"
+			"       .section        __ex_table,\"a\"\n"
+			STR(PTR_WD) " 1b,8b\n"
+			STR(PTR_WD) " 2b,8b\n"
+			STR(PTR_WD) " 3b,8b\n"
+			STR(PTR_WD) " 4b,8b\n"
+			STR(PTR_WD) " 5b,8b\n"
+			STR(PTR_WD) " 6b,8b\n"
+			STR(PTR_WD) " 7b,8b\n"
+			STR(PTR_WD) " 0b,8b\n"
+			"       .previous\n"
+			"       .set	pop\n"
+			: "+&r"(rt), "=&r"(rs),
+			  "+&r"(vaddr), "+&r"(err)
+			: "i"(SIGSEGV)
+			: "memory");
+
+		MIPS_R2_STATS(stores);
+
+		break;
+	case ll_op:
+		vaddr = regs->regs[MIPSInst_RS(inst)] + MIPSInst_SIMM(inst);
+		if (vaddr & 0x3) {
+			current->thread.cp0_baduaddr = vaddr;
+			err = SIGBUS;
+			break;
+		}
+		if (!access_ok((void __user *)vaddr, 4)) {
+			current->thread.cp0_baduaddr = vaddr;
+			err = SIGBUS;
+			break;
+		}
+
+		if (!cpu_has_rw_llb) {
+			/*
+			 * An LL/SC block can't be safely emulated without
+			 * a Config5/LLB availability. So it's probably time to
+			 * kill our process before things get any worse. This is
+			 * because Config5/LLB allows us to use ERETNC so that
+			 * the LLAddr/LLB bit is not cleared when we return from
+			 * an exception. MIPS R2 LL/SC instructions trap with an
+			 * RI exception so once we emulate them here, we return
+			 * back to userland with ERETNC. That preserves the
+			 * LLAddr/LLB so the subsequent SC instruction will
+			 * succeed preserving the atomic semantics of the LL/SC
+			 * block. Without that, there is no safe way to emulate
+			 * an LL/SC block in MIPSR2 userland.
+			 */
+			pr_err("Can't emulate MIPSR2 LL/SC without Config5/LLB\n");
+			err = SIGKILL;
+			break;
+		}
+
+		__asm__ __volatile__(
+			"1:\n"
+			"ll	%0, 0(%2)\n"
+			"2:\n"
+			".insn\n"
+			".section        .fixup,\"ax\"\n"
+			"3:\n"
+			"li	%1, %3\n"
+			"j	2b\n"
+			".previous\n"
+			".section        __ex_table,\"a\"\n"
+			STR(PTR_WD) " 1b,3b\n"
+			".previous\n"
+			: "=&r"(res), "+&r"(err)
+			: "r"(vaddr), "i"(SIGSEGV)
+			: "memory");
+
+		if (MIPSInst_RT(inst) && !err)
+			regs->regs[MIPSInst_RT(inst)] = res;
+		MIPS_R2_STATS(llsc);
+
+		break;
+
+	case sc_op:
+		vaddr = regs->regs[MIPSInst_RS(inst)] + MIPSInst_SIMM(inst);
+		if (vaddr & 0x3) {
+			current->thread.cp0_baduaddr = vaddr;
+			err = SIGBUS;
+			break;
+		}
+		if (!access_ok((void __user *)vaddr, 4)) {
+			current->thread.cp0_baduaddr = vaddr;
+			err = SIGBUS;
+			break;
+		}
+
+		if (!cpu_has_rw_llb) {
+			/*
+			 * An LL/SC block can't be safely emulated without
+			 * a Config5/LLB availability. So it's probably time to
+			 * kill our process before things get any worse. This is
+			 * because Config5/LLB allows us to use ERETNC so that
+			 * the LLAddr/LLB bit is not cleared when we return from
+			 * an exception. MIPS R2 LL/SC instructions trap with an
+			 * RI exception so once we emulate them here, we return
+			 * back to userland with ERETNC. That preserves the
+			 * LLAddr/LLB so the subsequent SC instruction will
+			 * succeed preserving the atomic semantics of the LL/SC
+			 * block. Without that, there is no safe way to emulate
+			 * an LL/SC block in MIPSR2 userland.
+			 */
+			pr_err("Can't emulate MIPSR2 LL/SC without Config5/LLB\n");
+			err = SIGKILL;
+			break;
+		}
+
+		res = regs->regs[MIPSInst_RT(inst)];
+
+		__asm__ __volatile__(
+			"1:\n"
+			"sc	%0, 0(%2)\n"
+			"2:\n"
+			".insn\n"
+			".section        .fixup,\"ax\"\n"
+			"3:\n"
+			"li	%1, %3\n"
+			"j	2b\n"
+			".previous\n"
+			".section        __ex_table,\"a\"\n"
+			STR(PTR_WD) " 1b,3b\n"
+			".previous\n"
+			: "+&r"(res), "+&r"(err)
+			: "r"(vaddr), "i"(SIGSEGV));
+
+		if (MIPSInst_RT(inst) && !err)
+			regs->regs[MIPSInst_RT(inst)] = res;
+
+		MIPS_R2_STATS(llsc);
+
+		break;
+
+	case lld_op:
+		if (IS_ENABLED(CONFIG_32BIT)) {
+		    err = SIGILL;
+		    break;
+		}
+
+		vaddr = regs->regs[MIPSInst_RS(inst)] + MIPSInst_SIMM(inst);
+		if (vaddr & 0x7) {
+			current->thread.cp0_baduaddr = vaddr;
+			err = SIGBUS;
+			break;
+		}
+		if (!access_ok((void __user *)vaddr, 8)) {
+			current->thread.cp0_baduaddr = vaddr;
+			err = SIGBUS;
+			break;
+		}
+
+		if (!cpu_has_rw_llb) {
+			/*
+			 * An LL/SC block can't be safely emulated without
+			 * a Config5/LLB availability. So it's probably time to
+			 * kill our process before things get any worse. This is
+			 * because Config5/LLB allows us to use ERETNC so that
+			 * the LLAddr/LLB bit is not cleared when we return from
+			 * an exception. MIPS R2 LL/SC instructions trap with an
+			 * RI exception so once we emulate them here, we return
+			 * back to userland with ERETNC. That preserves the
+			 * LLAddr/LLB so the subsequent SC instruction will
+			 * succeed preserving the atomic semantics of the LL/SC
+			 * block. Without that, there is no safe way to emulate
+			 * an LL/SC block in MIPSR2 userland.
+			 */
+			pr_err("Can't emulate MIPSR2 LL/SC without Config5/LLB\n");
+			err = SIGKILL;
+			break;
+		}
+
+		__asm__ __volatile__(
+			"1:\n"
+			"lld	%0, 0(%2)\n"
+			"2:\n"
+			".insn\n"
+			".section        .fixup,\"ax\"\n"
+			"3:\n"
+			"li	%1, %3\n"
+			"j	2b\n"
+			".previous\n"
+			".section        __ex_table,\"a\"\n"
+			STR(PTR_WD) " 1b,3b\n"
+			".previous\n"
+			: "=&r"(res), "+&r"(err)
+			: "r"(vaddr), "i"(SIGSEGV)
+			: "memory");
+		if (MIPSInst_RT(inst) && !err)
+			regs->regs[MIPSInst_RT(inst)] = res;
+
+		MIPS_R2_STATS(llsc);
+
+		break;
+
+	case scd_op:
+		if (IS_ENABLED(CONFIG_32BIT)) {
+		    err = SIGILL;
+		    break;
+		}
+
+		vaddr = regs->regs[MIPSInst_RS(inst)] + MIPSInst_SIMM(inst);
+		if (vaddr & 0x7) {
+			current->thread.cp0_baduaddr = vaddr;
+			err = SIGBUS;
+			break;
+		}
+		if (!access_ok((void __user *)vaddr, 8)) {
+			current->thread.cp0_baduaddr = vaddr;
+			err = SIGBUS;
+			break;
+		}
+
+		if (!cpu_has_rw_llb) {
+			/*
+			 * An LL/SC block can't be safely emulated without
+			 * a Config5/LLB availability. So it's probably time to
+			 * kill our process before things get any worse. This is
+			 * because Config5/LLB allows us to use ERETNC so that
+			 * the LLAddr/LLB bit is not cleared when we return from
+			 * an exception. MIPS R2 LL/SC instructions trap with an
+			 * RI exception so once we emulate them here, we return
+			 * back to userland with ERETNC. That preserves the
+			 * LLAddr/LLB so the subsequent SC instruction will
+			 * succeed preserving the atomic semantics of the LL/SC
+			 * block. Without that, there is no safe way to emulate
+			 * an LL/SC block in MIPSR2 userland.
+			 */
+			pr_err("Can't emulate MIPSR2 LL/SC without Config5/LLB\n");
+			err = SIGKILL;
+			break;
+		}
+
+		res = regs->regs[MIPSInst_RT(inst)];
+
+		__asm__ __volatile__(
+			"1:\n"
+			"scd	%0, 0(%2)\n"
+			"2:\n"
+			".insn\n"
+			".section        .fixup,\"ax\"\n"
+			"3:\n"
+			"li	%1, %3\n"
+			"j	2b\n"
+			".previous\n"
+			".section        __ex_table,\"a\"\n"
+			STR(PTR_WD) " 1b,3b\n"
+			".previous\n"
+			: "+&r"(res), "+&r"(err)
+			: "r"(vaddr), "i"(SIGSEGV));
+
+		if (MIPSInst_RT(inst) && !err)
+			regs->regs[MIPSInst_RT(inst)] = res;
+
+		MIPS_R2_STATS(llsc);
+
+		break;
+	case pref_op:
+		/* skip it */
+		break;
+	default:
+		err = SIGILL;
+	}
+
+	/*
+	 * Let's not return to userland just yet. It's costly and
+	 * it's likely we have more R2 instructions to emulate
+	 */
+	if (!err && (pass++ < MIPS_R2_EMUL_TOTAL_PASS)) {
+		regs->cp0_cause &= ~CAUSEF_BD;
+		err = get_user(inst, (u32 __user *)regs->cp0_epc);
+		if (!err)
+			goto repeat;
+
+		if (err < 0)
+			err = SIGSEGV;
+	}
+
+	if (err && (err != SIGEMT)) {
+		regs->regs[31] = r31;
+		regs->cp0_epc = epc;
+	}
+
+	/* Likely a MIPS R6 compatible instruction */
+	if (pass && (err == SIGILL))
+		err = 0;
+
+	return err;
+}
+
+#ifdef CONFIG_DEBUG_FS
+
+static int mipsr2_emul_show(struct seq_file *s, void *unused)
+{
+
+	seq_printf(s, "Instruction\tTotal\tBDslot\n------------------------------\n");
+	seq_printf(s, "movs\t\t%ld\t%ld\n",
+		   (unsigned long)__this_cpu_read(mipsr2emustats.movs),
+		   (unsigned long)__this_cpu_read(mipsr2bdemustats.movs));
+	seq_printf(s, "hilo\t\t%ld\t%ld\n",
+		   (unsigned long)__this_cpu_read(mipsr2emustats.hilo),
+		   (unsigned long)__this_cpu_read(mipsr2bdemustats.hilo));
+	seq_printf(s, "muls\t\t%ld\t%ld\n",
+		   (unsigned long)__this_cpu_read(mipsr2emustats.muls),
+		   (unsigned long)__this_cpu_read(mipsr2bdemustats.muls));
+	seq_printf(s, "divs\t\t%ld\t%ld\n",
+		   (unsigned long)__this_cpu_read(mipsr2emustats.divs),
+		   (unsigned long)__this_cpu_read(mipsr2bdemustats.divs));
+	seq_printf(s, "dsps\t\t%ld\t%ld\n",
+		   (unsigned long)__this_cpu_read(mipsr2emustats.dsps),
+		   (unsigned long)__this_cpu_read(mipsr2bdemustats.dsps));
+	seq_printf(s, "bops\t\t%ld\t%ld\n",
+		   (unsigned long)__this_cpu_read(mipsr2emustats.bops),
+		   (unsigned long)__this_cpu_read(mipsr2bdemustats.bops));
+	seq_printf(s, "traps\t\t%ld\t%ld\n",
+		   (unsigned long)__this_cpu_read(mipsr2emustats.traps),
+		   (unsigned long)__this_cpu_read(mipsr2bdemustats.traps));
+	seq_printf(s, "fpus\t\t%ld\t%ld\n",
+		   (unsigned long)__this_cpu_read(mipsr2emustats.fpus),
+		   (unsigned long)__this_cpu_read(mipsr2bdemustats.fpus));
+	seq_printf(s, "loads\t\t%ld\t%ld\n",
+		   (unsigned long)__this_cpu_read(mipsr2emustats.loads),
+		   (unsigned long)__this_cpu_read(mipsr2bdemustats.loads));
+	seq_printf(s, "stores\t\t%ld\t%ld\n",
+		   (unsigned long)__this_cpu_read(mipsr2emustats.stores),
+		   (unsigned long)__this_cpu_read(mipsr2bdemustats.stores));
+	seq_printf(s, "llsc\t\t%ld\t%ld\n",
+		   (unsigned long)__this_cpu_read(mipsr2emustats.llsc),
+		   (unsigned long)__this_cpu_read(mipsr2bdemustats.llsc));
+	seq_printf(s, "dsemul\t\t%ld\t%ld\n",
+		   (unsigned long)__this_cpu_read(mipsr2emustats.dsemul),
+		   (unsigned long)__this_cpu_read(mipsr2bdemustats.dsemul));
+	seq_printf(s, "jr\t\t%ld\n",
+		   (unsigned long)__this_cpu_read(mipsr2bremustats.jrs));
+	seq_printf(s, "bltzl\t\t%ld\n",
+		   (unsigned long)__this_cpu_read(mipsr2bremustats.bltzl));
+	seq_printf(s, "bgezl\t\t%ld\n",
+		   (unsigned long)__this_cpu_read(mipsr2bremustats.bgezl));
+	seq_printf(s, "bltzll\t\t%ld\n",
+		   (unsigned long)__this_cpu_read(mipsr2bremustats.bltzll));
+	seq_printf(s, "bgezll\t\t%ld\n",
+		   (unsigned long)__this_cpu_read(mipsr2bremustats.bgezll));
+	seq_printf(s, "bltzal\t\t%ld\n",
+		   (unsigned long)__this_cpu_read(mipsr2bremustats.bltzal));
+	seq_printf(s, "bgezal\t\t%ld\n",
+		   (unsigned long)__this_cpu_read(mipsr2bremustats.bgezal));
+	seq_printf(s, "beql\t\t%ld\n",
+		   (unsigned long)__this_cpu_read(mipsr2bremustats.beql));
+	seq_printf(s, "bnel\t\t%ld\n",
+		   (unsigned long)__this_cpu_read(mipsr2bremustats.bnel));
+	seq_printf(s, "blezl\t\t%ld\n",
+		   (unsigned long)__this_cpu_read(mipsr2bremustats.blezl));
+	seq_printf(s, "bgtzl\t\t%ld\n",
+		   (unsigned long)__this_cpu_read(mipsr2bremustats.bgtzl));
+
+	return 0;
+}
+
+static int mipsr2_clear_show(struct seq_file *s, void *unused)
+{
+	mipsr2_emul_show(s, unused);
+
+	__this_cpu_write((mipsr2emustats).movs, 0);
+	__this_cpu_write((mipsr2bdemustats).movs, 0);
+	__this_cpu_write((mipsr2emustats).hilo, 0);
+	__this_cpu_write((mipsr2bdemustats).hilo, 0);
+	__this_cpu_write((mipsr2emustats).muls, 0);
+	__this_cpu_write((mipsr2bdemustats).muls, 0);
+	__this_cpu_write((mipsr2emustats).divs, 0);
+	__this_cpu_write((mipsr2bdemustats).divs, 0);
+	__this_cpu_write((mipsr2emustats).dsps, 0);
+	__this_cpu_write((mipsr2bdemustats).dsps, 0);
+	__this_cpu_write((mipsr2emustats).bops, 0);
+	__this_cpu_write((mipsr2bdemustats).bops, 0);
+	__this_cpu_write((mipsr2emustats).traps, 0);
+	__this_cpu_write((mipsr2bdemustats).traps, 0);
+	__this_cpu_write((mipsr2emustats).fpus, 0);
+	__this_cpu_write((mipsr2bdemustats).fpus, 0);
+	__this_cpu_write((mipsr2emustats).loads, 0);
+	__this_cpu_write((mipsr2bdemustats).loads, 0);
+	__this_cpu_write((mipsr2emustats).stores, 0);
+	__this_cpu_write((mipsr2bdemustats).stores, 0);
+	__this_cpu_write((mipsr2emustats).llsc, 0);
+	__this_cpu_write((mipsr2bdemustats).llsc, 0);
+	__this_cpu_write((mipsr2emustats).dsemul, 0);
+	__this_cpu_write((mipsr2bdemustats).dsemul, 0);
+	__this_cpu_write((mipsr2bremustats).jrs, 0);
+	__this_cpu_write((mipsr2bremustats).bltzl, 0);
+	__this_cpu_write((mipsr2bremustats).bgezl, 0);
+	__this_cpu_write((mipsr2bremustats).bltzll, 0);
+	__this_cpu_write((mipsr2bremustats).bgezll, 0);
+	__this_cpu_write((mipsr2bremustats).bltzall, 0);
+	__this_cpu_write((mipsr2bremustats).bgezall, 0);
+	__this_cpu_write((mipsr2bremustats).bltzal, 0);
+	__this_cpu_write((mipsr2bremustats).bgezal, 0);
+	__this_cpu_write((mipsr2bremustats).beql, 0);
+	__this_cpu_write((mipsr2bremustats).bnel, 0);
+	__this_cpu_write((mipsr2bremustats).blezl, 0);
+	__this_cpu_write((mipsr2bremustats).bgtzl, 0);
+
+	return 0;
+}
+
+DEFINE_SHOW_ATTRIBUTE(mipsr2_emul);
+DEFINE_SHOW_ATTRIBUTE(mipsr2_clear);
+
+static int __init mipsr2_init_debugfs(void)
+{
+	debugfs_create_file("r2_emul_stats", S_IRUGO, mips_debugfs_dir, NULL,
+			    &mipsr2_emul_fops);
+	debugfs_create_file("r2_emul_stats_clear", S_IRUGO, mips_debugfs_dir,
+			    NULL, &mipsr2_clear_fops);
+	return 0;
+}
+
+device_initcall(mipsr2_init_debugfs);
+
+#endif /* CONFIG_DEBUG_FS */
diff --git a/arch/mips/kernel/module.c b/arch/mips/kernel/module.c
new file mode 100644
index 000000000..0c936cbf2
--- /dev/null
+++ b/arch/mips/kernel/module.c
@@ -0,0 +1,453 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *
+ *  Copyright (C) 2001 Rusty Russell.
+ *  Copyright (C) 2003, 2004 Ralf Baechle (ralf@linux-mips.org)
+ *  Copyright (C) 2005 Thiemo Seufer
+ */
+
+#undef DEBUG
+
+#include <linux/extable.h>
+#include <linux/moduleloader.h>
+#include <linux/elf.h>
+#include <linux/mm.h>
+#include <linux/numa.h>
+#include <linux/vmalloc.h>
+#include <linux/slab.h>
+#include <linux/fs.h>
+#include <linux/string.h>
+#include <linux/kernel.h>
+#include <linux/spinlock.h>
+#include <linux/jump_label.h>
+
+extern void jump_label_apply_nops(struct module *mod);
+
+struct mips_hi16 {
+	struct mips_hi16 *next;
+	Elf_Addr *addr;
+	Elf_Addr value;
+};
+
+static LIST_HEAD(dbe_list);
+static DEFINE_SPINLOCK(dbe_lock);
+
+#ifdef MODULE_START
+void *module_alloc(unsigned long size)
+{
+	return __vmalloc_node_range(size, 1, MODULE_START, MODULE_END,
+				GFP_KERNEL, PAGE_KERNEL, 0, NUMA_NO_NODE,
+				__builtin_return_address(0));
+}
+#endif
+
+static void apply_r_mips_32(u32 *location, u32 base, Elf_Addr v)
+{
+	*location = base + v;
+}
+
+static int apply_r_mips_26(struct module *me, u32 *location, u32 base,
+			   Elf_Addr v)
+{
+	if (v % 4) {
+		pr_err("module %s: dangerous R_MIPS_26 relocation\n",
+		       me->name);
+		return -ENOEXEC;
+	}
+
+	if ((v & 0xf0000000) != (((unsigned long)location + 4) & 0xf0000000)) {
+		pr_err("module %s: relocation overflow\n",
+		       me->name);
+		return -ENOEXEC;
+	}
+
+	*location = (*location & ~0x03ffffff) |
+		    ((base + (v >> 2)) & 0x03ffffff);
+
+	return 0;
+}
+
+static int apply_r_mips_hi16(struct module *me, u32 *location, Elf_Addr v,
+			     bool rela)
+{
+	struct mips_hi16 *n;
+
+	if (rela) {
+		*location = (*location & 0xffff0000) |
+			    ((((long long) v + 0x8000LL) >> 16) & 0xffff);
+		return 0;
+	}
+
+	/*
+	 * We cannot relocate this one now because we don't know the value of
+	 * the carry we need to add.  Save the information, and let LO16 do the
+	 * actual relocation.
+	 */
+	n = kmalloc(sizeof *n, GFP_KERNEL);
+	if (!n)
+		return -ENOMEM;
+
+	n->addr = (Elf_Addr *)location;
+	n->value = v;
+	n->next = me->arch.r_mips_hi16_list;
+	me->arch.r_mips_hi16_list = n;
+
+	return 0;
+}
+
+static void free_relocation_chain(struct mips_hi16 *l)
+{
+	struct mips_hi16 *next;
+
+	while (l) {
+		next = l->next;
+		kfree(l);
+		l = next;
+	}
+}
+
+static int apply_r_mips_lo16(struct module *me, u32 *location,
+			     u32 base, Elf_Addr v, bool rela)
+{
+	unsigned long insnlo = base;
+	struct mips_hi16 *l;
+	Elf_Addr val, vallo;
+
+	if (rela) {
+		*location = (*location & 0xffff0000) | (v & 0xffff);
+		return 0;
+	}
+
+	/* Sign extend the addend we extract from the lo insn.	*/
+	vallo = ((insnlo & 0xffff) ^ 0x8000) - 0x8000;
+
+	if (me->arch.r_mips_hi16_list != NULL) {
+		l = me->arch.r_mips_hi16_list;
+		while (l != NULL) {
+			struct mips_hi16 *next;
+			unsigned long insn;
+
+			/*
+			 * The value for the HI16 had best be the same.
+			 */
+			if (v != l->value)
+				goto out_danger;
+
+			/*
+			 * Do the HI16 relocation.  Note that we actually don't
+			 * need to know anything about the LO16 itself, except
+			 * where to find the low 16 bits of the addend needed
+			 * by the LO16.
+			 */
+			insn = *l->addr;
+			val = ((insn & 0xffff) << 16) + vallo;
+			val += v;
+
+			/*
+			 * Account for the sign extension that will happen in
+			 * the low bits.
+			 */
+			val = ((val >> 16) + ((val & 0x8000) != 0)) & 0xffff;
+
+			insn = (insn & ~0xffff) | val;
+			*l->addr = insn;
+
+			next = l->next;
+			kfree(l);
+			l = next;
+		}
+
+		me->arch.r_mips_hi16_list = NULL;
+	}
+
+	/*
+	 * Ok, we're done with the HI16 relocs.	 Now deal with the LO16.
+	 */
+	val = v + vallo;
+	insnlo = (insnlo & ~0xffff) | (val & 0xffff);
+	*location = insnlo;
+
+	return 0;
+
+out_danger:
+	free_relocation_chain(l);
+	me->arch.r_mips_hi16_list = NULL;
+
+	pr_err("module %s: dangerous R_MIPS_LO16 relocation\n", me->name);
+
+	return -ENOEXEC;
+}
+
+static int apply_r_mips_pc(struct module *me, u32 *location, u32 base,
+			   Elf_Addr v, unsigned int bits)
+{
+	unsigned long mask = GENMASK(bits - 1, 0);
+	unsigned long se_bits;
+	long offset;
+
+	if (v % 4) {
+		pr_err("module %s: dangerous R_MIPS_PC%u relocation\n",
+		       me->name, bits);
+		return -ENOEXEC;
+	}
+
+	/* retrieve & sign extend implicit addend if any */
+	offset = base & mask;
+	offset |= (offset & BIT(bits - 1)) ? ~mask : 0;
+
+	offset += ((long)v - (long)location) >> 2;
+
+	/* check the sign bit onwards are identical - ie. we didn't overflow */
+	se_bits = (offset & BIT(bits - 1)) ? ~0ul : 0;
+	if ((offset & ~mask) != (se_bits & ~mask)) {
+		pr_err("module %s: relocation overflow\n", me->name);
+		return -ENOEXEC;
+	}
+
+	*location = (*location & ~mask) | (offset & mask);
+
+	return 0;
+}
+
+static int apply_r_mips_pc16(struct module *me, u32 *location, u32 base,
+			     Elf_Addr v)
+{
+	return apply_r_mips_pc(me, location, base, v, 16);
+}
+
+static int apply_r_mips_pc21(struct module *me, u32 *location, u32 base,
+			     Elf_Addr v)
+{
+	return apply_r_mips_pc(me, location, base, v, 21);
+}
+
+static int apply_r_mips_pc26(struct module *me, u32 *location, u32 base,
+			     Elf_Addr v)
+{
+	return apply_r_mips_pc(me, location, base, v, 26);
+}
+
+static int apply_r_mips_64(u32 *location, Elf_Addr v, bool rela)
+{
+	if (WARN_ON(!rela))
+		return -EINVAL;
+
+	*(Elf_Addr *)location = v;
+
+	return 0;
+}
+
+static int apply_r_mips_higher(u32 *location, Elf_Addr v, bool rela)
+{
+	if (WARN_ON(!rela))
+		return -EINVAL;
+
+	*location = (*location & 0xffff0000) |
+		    ((((long long)v + 0x80008000LL) >> 32) & 0xffff);
+
+	return 0;
+}
+
+static int apply_r_mips_highest(u32 *location, Elf_Addr v, bool rela)
+{
+	if (WARN_ON(!rela))
+		return -EINVAL;
+
+	*location = (*location & 0xffff0000) |
+		    ((((long long)v + 0x800080008000LL) >> 48) & 0xffff);
+
+	return 0;
+}
+
+/**
+ * reloc_handler() - Apply a particular relocation to a module
+ * @type: type of the relocation to apply
+ * @me: the module to apply the reloc to
+ * @location: the address at which the reloc is to be applied
+ * @base: the existing value at location for REL-style; 0 for RELA-style
+ * @v: the value of the reloc, with addend for RELA-style
+ * @rela: indication of is this a RELA (true) or REL (false) relocation
+ *
+ * Each implemented relocation function applies a particular type of
+ * relocation to the module @me. Relocs that may be found in either REL or RELA
+ * variants can be handled by making use of the @base & @v parameters which are
+ * set to values which abstract the difference away from the particular reloc
+ * implementations.
+ *
+ * Return: 0 upon success, else -ERRNO
+ */
+static int reloc_handler(u32 type, struct module *me, u32 *location, u32 base,
+			 Elf_Addr v, bool rela)
+{
+	switch (type) {
+	case R_MIPS_NONE:
+		break;
+	case R_MIPS_32:
+		apply_r_mips_32(location, base, v);
+		break;
+	case R_MIPS_26:
+		return apply_r_mips_26(me, location, base, v);
+	case R_MIPS_HI16:
+		return apply_r_mips_hi16(me, location, v, rela);
+	case R_MIPS_LO16:
+		return apply_r_mips_lo16(me, location, base, v, rela);
+	case R_MIPS_PC16:
+		return apply_r_mips_pc16(me, location, base, v);
+	case R_MIPS_PC21_S2:
+		return apply_r_mips_pc21(me, location, base, v);
+	case R_MIPS_PC26_S2:
+		return apply_r_mips_pc26(me, location, base, v);
+	case R_MIPS_64:
+		return apply_r_mips_64(location, v, rela);
+	case R_MIPS_HIGHER:
+		return apply_r_mips_higher(location, v, rela);
+	case R_MIPS_HIGHEST:
+		return apply_r_mips_highest(location, v, rela);
+	default:
+		pr_err("%s: Unknown relocation type %u\n", me->name, type);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int __apply_relocate(Elf_Shdr *sechdrs, const char *strtab,
+			    unsigned int symindex, unsigned int relsec,
+			    struct module *me, bool rela)
+{
+	union {
+		Elf_Mips_Rel *rel;
+		Elf_Mips_Rela *rela;
+	} r;
+	Elf_Sym *sym;
+	u32 *location, base;
+	unsigned int i, type;
+	Elf_Addr v;
+	int err = 0;
+	size_t reloc_sz;
+
+	pr_debug("Applying relocate section %u to %u\n", relsec,
+	       sechdrs[relsec].sh_info);
+
+	r.rel = (void *)sechdrs[relsec].sh_addr;
+	reloc_sz = rela ? sizeof(*r.rela) : sizeof(*r.rel);
+	me->arch.r_mips_hi16_list = NULL;
+	for (i = 0; i < sechdrs[relsec].sh_size / reloc_sz; i++) {
+		/* This is where to make the change */
+		location = (void *)sechdrs[sechdrs[relsec].sh_info].sh_addr
+			+ r.rel->r_offset;
+		/* This is the symbol it is referring to */
+		sym = (Elf_Sym *)sechdrs[symindex].sh_addr
+			+ ELF_MIPS_R_SYM(*r.rel);
+		if (sym->st_value >= -MAX_ERRNO) {
+			/* Ignore unresolved weak symbol */
+			if (ELF_ST_BIND(sym->st_info) == STB_WEAK)
+				continue;
+			pr_warn("%s: Unknown symbol %s\n",
+				me->name, strtab + sym->st_name);
+			err = -ENOENT;
+			goto out;
+		}
+
+		type = ELF_MIPS_R_TYPE(*r.rel);
+
+		if (rela) {
+			v = sym->st_value + r.rela->r_addend;
+			base = 0;
+			r.rela = &r.rela[1];
+		} else {
+			v = sym->st_value;
+			base = *location;
+			r.rel = &r.rel[1];
+		}
+
+		err = reloc_handler(type, me, location, base, v, rela);
+		if (err)
+			goto out;
+	}
+
+out:
+	/*
+	 * Normally the hi16 list should be deallocated at this point. A
+	 * malformed binary however could contain a series of R_MIPS_HI16
+	 * relocations not followed by a R_MIPS_LO16 relocation, or if we hit
+	 * an error processing a reloc we might have gotten here before
+	 * reaching the R_MIPS_LO16. In either case, free up the list and
+	 * return an error.
+	 */
+	if (me->arch.r_mips_hi16_list) {
+		free_relocation_chain(me->arch.r_mips_hi16_list);
+		me->arch.r_mips_hi16_list = NULL;
+		err = err ?: -ENOEXEC;
+	}
+
+	return err;
+}
+
+int apply_relocate(Elf_Shdr *sechdrs, const char *strtab,
+		   unsigned int symindex, unsigned int relsec,
+		   struct module *me)
+{
+	return __apply_relocate(sechdrs, strtab, symindex, relsec, me, false);
+}
+
+#ifdef CONFIG_MODULES_USE_ELF_RELA
+int apply_relocate_add(Elf_Shdr *sechdrs, const char *strtab,
+		       unsigned int symindex, unsigned int relsec,
+		       struct module *me)
+{
+	return __apply_relocate(sechdrs, strtab, symindex, relsec, me, true);
+}
+#endif /* CONFIG_MODULES_USE_ELF_RELA */
+
+/* Given an address, look for it in the module exception tables. */
+const struct exception_table_entry *search_module_dbetables(unsigned long addr)
+{
+	unsigned long flags;
+	const struct exception_table_entry *e = NULL;
+	struct mod_arch_specific *dbe;
+
+	spin_lock_irqsave(&dbe_lock, flags);
+	list_for_each_entry(dbe, &dbe_list, dbe_list) {
+		e = search_extable(dbe->dbe_start,
+				   dbe->dbe_end - dbe->dbe_start, addr);
+		if (e)
+			break;
+	}
+	spin_unlock_irqrestore(&dbe_lock, flags);
+
+	/* Now, if we found one, we are running inside it now, hence
+	   we cannot unload the module, hence no refcnt needed. */
+	return e;
+}
+
+/* Put in dbe list if necessary. */
+int module_finalize(const Elf_Ehdr *hdr,
+		    const Elf_Shdr *sechdrs,
+		    struct module *me)
+{
+	const Elf_Shdr *s;
+	char *secstrings = (void *)hdr + sechdrs[hdr->e_shstrndx].sh_offset;
+
+	if (IS_ENABLED(CONFIG_JUMP_LABEL))
+		jump_label_apply_nops(me);
+
+	INIT_LIST_HEAD(&me->arch.dbe_list);
+	for (s = sechdrs; s < sechdrs + hdr->e_shnum; s++) {
+		if (strcmp("__dbe_table", secstrings + s->sh_name) != 0)
+			continue;
+		me->arch.dbe_start = (void *)s->sh_addr;
+		me->arch.dbe_end = (void *)s->sh_addr + s->sh_size;
+		spin_lock_irq(&dbe_lock);
+		list_add(&me->arch.dbe_list, &dbe_list);
+		spin_unlock_irq(&dbe_lock);
+	}
+	return 0;
+}
+
+void module_arch_cleanup(struct module *mod)
+{
+	spin_lock_irq(&dbe_lock);
+	list_del(&mod->arch.dbe_list);
+	spin_unlock_irq(&dbe_lock);
+}
diff --git a/arch/mips/kernel/octeon_switch.S b/arch/mips/kernel/octeon_switch.S
new file mode 100644
index 000000000..896080b44
--- /dev/null
+++ b/arch/mips/kernel/octeon_switch.S
@@ -0,0 +1,554 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994, 1995, 1996, 1998, 1999, 2002, 2003 Ralf Baechle
+ * Copyright (C) 1996 David S. Miller (davem@davemloft.net)
+ * Copyright (C) 1994, 1995, 1996, by Andreas Busse
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ * Copyright (C) 2000 MIPS Technologies, Inc.
+ *    written by Carsten Langgaard, carstenl@mips.com
+ */
+#include <asm/asm.h>
+#include <asm/export.h>
+#include <asm/asm-offsets.h>
+#include <asm/mipsregs.h>
+#include <asm/regdef.h>
+#include <asm/stackframe.h>
+
+/*
+ * task_struct *resume(task_struct *prev, task_struct *next,
+ *		       struct thread_info *next_ti)
+ */
+	.align	7
+	LEAF(resume)
+	.set arch=octeon
+	mfc0	t1, CP0_STATUS
+	LONG_S	t1, THREAD_STATUS(a0)
+	cpu_save_nonscratch a0
+	LONG_S	ra, THREAD_REG31(a0)
+
+#if CONFIG_CAVIUM_OCTEON_CVMSEG_SIZE > 0
+	/* Check if we need to store CVMSEG state */
+	dmfc0	t0, $11,7	/* CvmMemCtl */
+	bbit0	t0, 6, 3f	/* Is user access enabled? */
+
+	/* Store the CVMSEG state */
+	/* Extract the size of CVMSEG */
+	andi	t0, 0x3f
+	/* Multiply * (cache line size/sizeof(long)/2) */
+	sll	t0, 7-LONGLOG-1
+	li	t1, -32768	/* Base address of CVMSEG */
+	LONG_ADDI t2, a0, THREAD_CVMSEG /* Where to store CVMSEG to */
+	synciobdma
+2:
+	.set noreorder
+	LONG_L	t8, 0(t1)	/* Load from CVMSEG */
+	subu	t0, 1		/* Decrement loop var */
+	LONG_L	t9, LONGSIZE(t1)/* Load from CVMSEG */
+	LONG_ADDU t1, LONGSIZE*2 /* Increment loc in CVMSEG */
+	LONG_S	t8, 0(t2)	/* Store CVMSEG to thread storage */
+	LONG_ADDU t2, LONGSIZE*2 /* Increment loc in thread storage */
+	bnez	t0, 2b		/* Loop until we've copied it all */
+	 LONG_S t9, -LONGSIZE(t2)/* Store CVMSEG to thread storage */
+	.set reorder
+
+	/* Disable access to CVMSEG */
+	dmfc0	t0, $11,7	/* CvmMemCtl */
+	xori	t0, t0, 0x40	/* Bit 6 is CVMSEG user enable */
+	dmtc0	t0, $11,7	/* CvmMemCtl */
+#endif
+3:
+
+#if defined(CONFIG_STACKPROTECTOR) && !defined(CONFIG_SMP)
+	PTR_LA	t8, __stack_chk_guard
+	LONG_L	t9, TASK_STACK_CANARY(a1)
+	LONG_S	t9, 0(t8)
+#endif
+
+	/*
+	 * The order of restoring the registers takes care of the race
+	 * updating $28, $29 and kernelsp without disabling ints.
+	 */
+	move	$28, a2
+	cpu_restore_nonscratch a1
+
+	PTR_ADDU	t0, $28, _THREAD_SIZE - 32
+	set_saved_sp	t0, t1, t2
+
+	mfc0	t1, CP0_STATUS		/* Do we really need this? */
+	li	a3, 0xff01
+	and	t1, a3
+	LONG_L	a2, THREAD_STATUS(a1)
+	nor	a3, $0, a3
+	and	a2, a3
+	or	a2, t1
+	mtc0	a2, CP0_STATUS
+	move	v0, a0
+	jr	ra
+	END(resume)
+
+/*
+ * void octeon_cop2_save(struct octeon_cop2_state *a0)
+ */
+	.align	7
+	.set push
+	.set noreorder
+	LEAF(octeon_cop2_save)
+
+	dmfc0	t9, $9,7	/* CvmCtl register. */
+
+	/* Save the COP2 CRC state */
+	dmfc2	t0, 0x0201
+	dmfc2	t1, 0x0202
+	dmfc2	t2, 0x0200
+	sd	t0, OCTEON_CP2_CRC_IV(a0)
+	sd	t1, OCTEON_CP2_CRC_LENGTH(a0)
+	/* Skip next instructions if CvmCtl[NODFA_CP2] set */
+	bbit1	t9, 28, 1f
+	 sd	t2, OCTEON_CP2_CRC_POLY(a0)
+
+	/* Save the LLM state */
+	dmfc2	t0, 0x0402
+	dmfc2	t1, 0x040A
+	sd	t0, OCTEON_CP2_LLM_DAT(a0)
+
+1:	bbit1	t9, 26, 3f	/* done if CvmCtl[NOCRYPTO] set */
+	 sd	t1, OCTEON_CP2_LLM_DAT+8(a0)
+
+	/* Save the COP2 crypto state */
+	/* this part is mostly common to both pass 1 and later revisions */
+	dmfc2	t0, 0x0084
+	dmfc2	t1, 0x0080
+	dmfc2	t2, 0x0081
+	dmfc2	t3, 0x0082
+	sd	t0, OCTEON_CP2_3DES_IV(a0)
+	dmfc2	t0, 0x0088
+	sd	t1, OCTEON_CP2_3DES_KEY(a0)
+	dmfc2	t1, 0x0111			/* only necessary for pass 1 */
+	sd	t2, OCTEON_CP2_3DES_KEY+8(a0)
+	dmfc2	t2, 0x0102
+	sd	t3, OCTEON_CP2_3DES_KEY+16(a0)
+	dmfc2	t3, 0x0103
+	sd	t0, OCTEON_CP2_3DES_RESULT(a0)
+	dmfc2	t0, 0x0104
+	sd	t1, OCTEON_CP2_AES_INP0(a0)	/* only necessary for pass 1 */
+	dmfc2	t1, 0x0105
+	sd	t2, OCTEON_CP2_AES_IV(a0)
+	dmfc2	t2, 0x0106
+	sd	t3, OCTEON_CP2_AES_IV+8(a0)
+	dmfc2	t3, 0x0107
+	sd	t0, OCTEON_CP2_AES_KEY(a0)
+	dmfc2	t0, 0x0110
+	sd	t1, OCTEON_CP2_AES_KEY+8(a0)
+	dmfc2	t1, 0x0100
+	sd	t2, OCTEON_CP2_AES_KEY+16(a0)
+	dmfc2	t2, 0x0101
+	sd	t3, OCTEON_CP2_AES_KEY+24(a0)
+	mfc0	v0, $15,0	/* Get the processor ID register */
+	sd	t0, OCTEON_CP2_AES_KEYLEN(a0)
+	li	v1, 0x000d0000	/* This is the processor ID of Octeon Pass1 */
+	sd	t1, OCTEON_CP2_AES_RESULT(a0)
+	/* Skip to the Pass1 version of the remainder of the COP2 state */
+	beq	v0, v1, 2f
+	 sd	t2, OCTEON_CP2_AES_RESULT+8(a0)
+
+	/* the non-pass1 state when !CvmCtl[NOCRYPTO] */
+	dmfc2	t1, 0x0240
+	dmfc2	t2, 0x0241
+	ori	v1, v1, 0x9500 /* lowest OCTEON III PrId*/
+	dmfc2	t3, 0x0242
+	subu	v1, v0, v1 /* prid - lowest OCTEON III PrId */
+	dmfc2	t0, 0x0243
+	sd	t1, OCTEON_CP2_HSH_DATW(a0)
+	dmfc2	t1, 0x0244
+	sd	t2, OCTEON_CP2_HSH_DATW+8(a0)
+	dmfc2	t2, 0x0245
+	sd	t3, OCTEON_CP2_HSH_DATW+16(a0)
+	dmfc2	t3, 0x0246
+	sd	t0, OCTEON_CP2_HSH_DATW+24(a0)
+	dmfc2	t0, 0x0247
+	sd	t1, OCTEON_CP2_HSH_DATW+32(a0)
+	dmfc2	t1, 0x0248
+	sd	t2, OCTEON_CP2_HSH_DATW+40(a0)
+	dmfc2	t2, 0x0249
+	sd	t3, OCTEON_CP2_HSH_DATW+48(a0)
+	dmfc2	t3, 0x024A
+	sd	t0, OCTEON_CP2_HSH_DATW+56(a0)
+	dmfc2	t0, 0x024B
+	sd	t1, OCTEON_CP2_HSH_DATW+64(a0)
+	dmfc2	t1, 0x024C
+	sd	t2, OCTEON_CP2_HSH_DATW+72(a0)
+	dmfc2	t2, 0x024D
+	sd	t3, OCTEON_CP2_HSH_DATW+80(a0)
+	dmfc2	t3, 0x024E
+	sd	t0, OCTEON_CP2_HSH_DATW+88(a0)
+	dmfc2	t0, 0x0250
+	sd	t1, OCTEON_CP2_HSH_DATW+96(a0)
+	dmfc2	t1, 0x0251
+	sd	t2, OCTEON_CP2_HSH_DATW+104(a0)
+	dmfc2	t2, 0x0252
+	sd	t3, OCTEON_CP2_HSH_DATW+112(a0)
+	dmfc2	t3, 0x0253
+	sd	t0, OCTEON_CP2_HSH_IVW(a0)
+	dmfc2	t0, 0x0254
+	sd	t1, OCTEON_CP2_HSH_IVW+8(a0)
+	dmfc2	t1, 0x0255
+	sd	t2, OCTEON_CP2_HSH_IVW+16(a0)
+	dmfc2	t2, 0x0256
+	sd	t3, OCTEON_CP2_HSH_IVW+24(a0)
+	dmfc2	t3, 0x0257
+	sd	t0, OCTEON_CP2_HSH_IVW+32(a0)
+	dmfc2	t0, 0x0258
+	sd	t1, OCTEON_CP2_HSH_IVW+40(a0)
+	dmfc2	t1, 0x0259
+	sd	t2, OCTEON_CP2_HSH_IVW+48(a0)
+	dmfc2	t2, 0x025E
+	sd	t3, OCTEON_CP2_HSH_IVW+56(a0)
+	dmfc2	t3, 0x025A
+	sd	t0, OCTEON_CP2_GFM_MULT(a0)
+	dmfc2	t0, 0x025B
+	sd	t1, OCTEON_CP2_GFM_MULT+8(a0)
+	sd	t2, OCTEON_CP2_GFM_POLY(a0)
+	sd	t3, OCTEON_CP2_GFM_RESULT(a0)
+	bltz	v1, 4f
+	 sd	t0, OCTEON_CP2_GFM_RESULT+8(a0)
+	/* OCTEON III things*/
+	dmfc2	t0, 0x024F
+	dmfc2	t1, 0x0050
+	sd	t0, OCTEON_CP2_SHA3(a0)
+	sd	t1, OCTEON_CP2_SHA3+8(a0)
+4:
+	jr	ra
+	 nop
+
+2:	/* pass 1 special stuff when !CvmCtl[NOCRYPTO] */
+	dmfc2	t3, 0x0040
+	dmfc2	t0, 0x0041
+	dmfc2	t1, 0x0042
+	dmfc2	t2, 0x0043
+	sd	t3, OCTEON_CP2_HSH_DATW(a0)
+	dmfc2	t3, 0x0044
+	sd	t0, OCTEON_CP2_HSH_DATW+8(a0)
+	dmfc2	t0, 0x0045
+	sd	t1, OCTEON_CP2_HSH_DATW+16(a0)
+	dmfc2	t1, 0x0046
+	sd	t2, OCTEON_CP2_HSH_DATW+24(a0)
+	dmfc2	t2, 0x0048
+	sd	t3, OCTEON_CP2_HSH_DATW+32(a0)
+	dmfc2	t3, 0x0049
+	sd	t0, OCTEON_CP2_HSH_DATW+40(a0)
+	dmfc2	t0, 0x004A
+	sd	t1, OCTEON_CP2_HSH_DATW+48(a0)
+	sd	t2, OCTEON_CP2_HSH_IVW(a0)
+	sd	t3, OCTEON_CP2_HSH_IVW+8(a0)
+	sd	t0, OCTEON_CP2_HSH_IVW+16(a0)
+
+3:	/* pass 1 or CvmCtl[NOCRYPTO] set */
+	jr	ra
+	 nop
+	END(octeon_cop2_save)
+	.set pop
+
+/*
+ * void octeon_cop2_restore(struct octeon_cop2_state *a0)
+ */
+	.align	7
+	.set push
+	.set noreorder
+	LEAF(octeon_cop2_restore)
+	/* First cache line was prefetched before the call */
+	pref	4,  128(a0)
+	dmfc0	t9, $9,7	/* CvmCtl register. */
+
+	pref	4,  256(a0)
+	ld	t0, OCTEON_CP2_CRC_IV(a0)
+	pref	4,  384(a0)
+	ld	t1, OCTEON_CP2_CRC_LENGTH(a0)
+	ld	t2, OCTEON_CP2_CRC_POLY(a0)
+
+	/* Restore the COP2 CRC state */
+	dmtc2	t0, 0x0201
+	dmtc2	t1, 0x1202
+	bbit1	t9, 28, 2f	/* Skip LLM if CvmCtl[NODFA_CP2] is set */
+	 dmtc2	t2, 0x4200
+
+	/* Restore the LLM state */
+	ld	t0, OCTEON_CP2_LLM_DAT(a0)
+	ld	t1, OCTEON_CP2_LLM_DAT+8(a0)
+	dmtc2	t0, 0x0402
+	dmtc2	t1, 0x040A
+
+2:
+	bbit1	t9, 26, done_restore	/* done if CvmCtl[NOCRYPTO] set */
+	 nop
+
+	/* Restore the COP2 crypto state common to pass 1 and pass 2 */
+	ld	t0, OCTEON_CP2_3DES_IV(a0)
+	ld	t1, OCTEON_CP2_3DES_KEY(a0)
+	ld	t2, OCTEON_CP2_3DES_KEY+8(a0)
+	dmtc2	t0, 0x0084
+	ld	t0, OCTEON_CP2_3DES_KEY+16(a0)
+	dmtc2	t1, 0x0080
+	ld	t1, OCTEON_CP2_3DES_RESULT(a0)
+	dmtc2	t2, 0x0081
+	ld	t2, OCTEON_CP2_AES_INP0(a0) /* only really needed for pass 1 */
+	dmtc2	t0, 0x0082
+	ld	t0, OCTEON_CP2_AES_IV(a0)
+	dmtc2	t1, 0x0098
+	ld	t1, OCTEON_CP2_AES_IV+8(a0)
+	dmtc2	t2, 0x010A		    /* only really needed for pass 1 */
+	ld	t2, OCTEON_CP2_AES_KEY(a0)
+	dmtc2	t0, 0x0102
+	ld	t0, OCTEON_CP2_AES_KEY+8(a0)
+	dmtc2	t1, 0x0103
+	ld	t1, OCTEON_CP2_AES_KEY+16(a0)
+	dmtc2	t2, 0x0104
+	ld	t2, OCTEON_CP2_AES_KEY+24(a0)
+	dmtc2	t0, 0x0105
+	ld	t0, OCTEON_CP2_AES_KEYLEN(a0)
+	dmtc2	t1, 0x0106
+	ld	t1, OCTEON_CP2_AES_RESULT(a0)
+	dmtc2	t2, 0x0107
+	ld	t2, OCTEON_CP2_AES_RESULT+8(a0)
+	mfc0	t3, $15,0	/* Get the processor ID register */
+	dmtc2	t0, 0x0110
+	li	v0, 0x000d0000	/* This is the processor ID of Octeon Pass1 */
+	dmtc2	t1, 0x0100
+	bne	v0, t3, 3f	/* Skip the next stuff for non-pass1 */
+	 dmtc2	t2, 0x0101
+
+	/* this code is specific for pass 1 */
+	ld	t0, OCTEON_CP2_HSH_DATW(a0)
+	ld	t1, OCTEON_CP2_HSH_DATW+8(a0)
+	ld	t2, OCTEON_CP2_HSH_DATW+16(a0)
+	dmtc2	t0, 0x0040
+	ld	t0, OCTEON_CP2_HSH_DATW+24(a0)
+	dmtc2	t1, 0x0041
+	ld	t1, OCTEON_CP2_HSH_DATW+32(a0)
+	dmtc2	t2, 0x0042
+	ld	t2, OCTEON_CP2_HSH_DATW+40(a0)
+	dmtc2	t0, 0x0043
+	ld	t0, OCTEON_CP2_HSH_DATW+48(a0)
+	dmtc2	t1, 0x0044
+	ld	t1, OCTEON_CP2_HSH_IVW(a0)
+	dmtc2	t2, 0x0045
+	ld	t2, OCTEON_CP2_HSH_IVW+8(a0)
+	dmtc2	t0, 0x0046
+	ld	t0, OCTEON_CP2_HSH_IVW+16(a0)
+	dmtc2	t1, 0x0048
+	dmtc2	t2, 0x0049
+	b done_restore	 /* unconditional branch */
+	 dmtc2	t0, 0x004A
+
+3:	/* this is post-pass1 code */
+	ld	t2, OCTEON_CP2_HSH_DATW(a0)
+	ori	v0, v0, 0x9500 /* lowest OCTEON III PrId*/
+	ld	t0, OCTEON_CP2_HSH_DATW+8(a0)
+	ld	t1, OCTEON_CP2_HSH_DATW+16(a0)
+	dmtc2	t2, 0x0240
+	ld	t2, OCTEON_CP2_HSH_DATW+24(a0)
+	dmtc2	t0, 0x0241
+	ld	t0, OCTEON_CP2_HSH_DATW+32(a0)
+	dmtc2	t1, 0x0242
+	ld	t1, OCTEON_CP2_HSH_DATW+40(a0)
+	dmtc2	t2, 0x0243
+	ld	t2, OCTEON_CP2_HSH_DATW+48(a0)
+	dmtc2	t0, 0x0244
+	ld	t0, OCTEON_CP2_HSH_DATW+56(a0)
+	dmtc2	t1, 0x0245
+	ld	t1, OCTEON_CP2_HSH_DATW+64(a0)
+	dmtc2	t2, 0x0246
+	ld	t2, OCTEON_CP2_HSH_DATW+72(a0)
+	dmtc2	t0, 0x0247
+	ld	t0, OCTEON_CP2_HSH_DATW+80(a0)
+	dmtc2	t1, 0x0248
+	ld	t1, OCTEON_CP2_HSH_DATW+88(a0)
+	dmtc2	t2, 0x0249
+	ld	t2, OCTEON_CP2_HSH_DATW+96(a0)
+	dmtc2	t0, 0x024A
+	ld	t0, OCTEON_CP2_HSH_DATW+104(a0)
+	dmtc2	t1, 0x024B
+	ld	t1, OCTEON_CP2_HSH_DATW+112(a0)
+	dmtc2	t2, 0x024C
+	ld	t2, OCTEON_CP2_HSH_IVW(a0)
+	dmtc2	t0, 0x024D
+	ld	t0, OCTEON_CP2_HSH_IVW+8(a0)
+	dmtc2	t1, 0x024E
+	ld	t1, OCTEON_CP2_HSH_IVW+16(a0)
+	dmtc2	t2, 0x0250
+	ld	t2, OCTEON_CP2_HSH_IVW+24(a0)
+	dmtc2	t0, 0x0251
+	ld	t0, OCTEON_CP2_HSH_IVW+32(a0)
+	dmtc2	t1, 0x0252
+	ld	t1, OCTEON_CP2_HSH_IVW+40(a0)
+	dmtc2	t2, 0x0253
+	ld	t2, OCTEON_CP2_HSH_IVW+48(a0)
+	dmtc2	t0, 0x0254
+	ld	t0, OCTEON_CP2_HSH_IVW+56(a0)
+	dmtc2	t1, 0x0255
+	ld	t1, OCTEON_CP2_GFM_MULT(a0)
+	dmtc2	t2, 0x0256
+	ld	t2, OCTEON_CP2_GFM_MULT+8(a0)
+	dmtc2	t0, 0x0257
+	ld	t0, OCTEON_CP2_GFM_POLY(a0)
+	dmtc2	t1, 0x0258
+	ld	t1, OCTEON_CP2_GFM_RESULT(a0)
+	dmtc2	t2, 0x0259
+	ld	t2, OCTEON_CP2_GFM_RESULT+8(a0)
+	dmtc2	t0, 0x025E
+	subu	v0, t3, v0 /* prid - lowest OCTEON III PrId */
+	dmtc2	t1, 0x025A
+	bltz	v0, done_restore
+	 dmtc2	t2, 0x025B
+	/* OCTEON III things*/
+	ld	t0, OCTEON_CP2_SHA3(a0)
+	ld	t1, OCTEON_CP2_SHA3+8(a0)
+	dmtc2	t0, 0x0051
+	dmtc2	t1, 0x0050
+done_restore:
+	jr	ra
+	 nop
+	END(octeon_cop2_restore)
+	.set pop
+
+/*
+ * void octeon_mult_save()
+ * sp is assumed to point to a struct pt_regs
+ *
+ * NOTE: This is called in SAVE_TEMP in stackframe.h. It can
+ *       safely modify v1,k0, k1,$10-$15, and $24.  It will
+ *	 be overwritten with a processor specific version of the code.
+ */
+	.p2align 7
+	.set push
+	.set noreorder
+	LEAF(octeon_mult_save)
+	jr	ra
+	 nop
+	.space 30 * 4, 0
+octeon_mult_save_end:
+	EXPORT(octeon_mult_save_end)
+	END(octeon_mult_save)
+
+	LEAF(octeon_mult_save2)
+	/* Save the multiplier state OCTEON II and earlier*/
+	v3mulu	k0, $0, $0
+	v3mulu	k1, $0, $0
+	sd	k0, PT_MTP(sp)	      /* PT_MTP	   has P0 */
+	v3mulu	k0, $0, $0
+	sd	k1, PT_MTP+8(sp)      /* PT_MTP+8  has P1 */
+	ori	k1, $0, 1
+	v3mulu	k1, k1, $0
+	sd	k0, PT_MTP+16(sp)     /* PT_MTP+16 has P2 */
+	v3mulu	k0, $0, $0
+	sd	k1, PT_MPL(sp)	      /* PT_MPL	   has MPL0 */
+	v3mulu	k1, $0, $0
+	sd	k0, PT_MPL+8(sp)      /* PT_MPL+8  has MPL1 */
+	jr	ra
+	 sd	k1, PT_MPL+16(sp)     /* PT_MPL+16 has MPL2 */
+octeon_mult_save2_end:
+	EXPORT(octeon_mult_save2_end)
+	END(octeon_mult_save2)
+
+	LEAF(octeon_mult_save3)
+	/* Save the multiplier state OCTEON III */
+	v3mulu	$10, $0, $0		/* read P0 */
+	v3mulu	$11, $0, $0		/* read P1 */
+	v3mulu	$12, $0, $0		/* read P2 */
+	sd	$10, PT_MTP+(0*8)(sp)	/* store P0 */
+	v3mulu	$10, $0, $0		/* read P3 */
+	sd	$11, PT_MTP+(1*8)(sp)	/*  store P1 */
+	v3mulu	$11, $0, $0		/* read P4 */
+	sd	$12, PT_MTP+(2*8)(sp)	/* store P2 */
+	ori	$13, $0, 1
+	v3mulu	$12, $0, $0		/* read P5 */
+	sd	$10, PT_MTP+(3*8)(sp)	/* store P3 */
+	v3mulu	$13, $13, $0		/* P4-P0 = MPL5-MPL1, $13 = MPL0 */
+	sd	$11, PT_MTP+(4*8)(sp)	/* store P4 */
+	v3mulu	$10, $0, $0		/* read MPL1 */
+	sd	$12, PT_MTP+(5*8)(sp)	/* store P5 */
+	v3mulu	$11, $0, $0		/* read MPL2 */
+	sd	$13, PT_MPL+(0*8)(sp)	/* store MPL0 */
+	v3mulu	$12, $0, $0		/* read MPL3 */
+	sd	$10, PT_MPL+(1*8)(sp)	/* store MPL1 */
+	v3mulu	$10, $0, $0		/* read MPL4 */
+	sd	$11, PT_MPL+(2*8)(sp)	/* store MPL2 */
+	v3mulu	$11, $0, $0		/* read MPL5 */
+	sd	$12, PT_MPL+(3*8)(sp)	/* store MPL3 */
+	sd	$10, PT_MPL+(4*8)(sp)	/* store MPL4 */
+	jr	ra
+	 sd	$11, PT_MPL+(5*8)(sp)	/* store MPL5 */
+octeon_mult_save3_end:
+	EXPORT(octeon_mult_save3_end)
+	END(octeon_mult_save3)
+	.set pop
+
+/*
+ * void octeon_mult_restore()
+ * sp is assumed to point to a struct pt_regs
+ *
+ * NOTE: This is called in RESTORE_TEMP in stackframe.h.
+ */
+	.p2align 7
+	.set push
+	.set noreorder
+	LEAF(octeon_mult_restore)
+	jr	ra
+	 nop
+	.space 30 * 4, 0
+octeon_mult_restore_end:
+	EXPORT(octeon_mult_restore_end)
+	END(octeon_mult_restore)
+
+	LEAF(octeon_mult_restore2)
+	ld	v0, PT_MPL(sp)        	/* MPL0 */
+	ld	v1, PT_MPL+8(sp)      	/* MPL1 */
+	ld	k0, PT_MPL+16(sp)     	/* MPL2 */
+	/* Restore the multiplier state */
+	ld	k1, PT_MTP+16(sp)     	/* P2 */
+	mtm0	v0			/* MPL0 */
+	ld	v0, PT_MTP+8(sp)	/* P1 */
+	mtm1	v1			/* MPL1 */
+	ld	v1, PT_MTP(sp)   	/* P0 */
+	mtm2	k0			/* MPL2 */
+	mtp2	k1			/* P2 */
+	mtp1	v0			/* P1 */
+	jr	ra
+	 mtp0	v1			/* P0 */
+octeon_mult_restore2_end:
+	EXPORT(octeon_mult_restore2_end)
+	END(octeon_mult_restore2)
+
+	LEAF(octeon_mult_restore3)
+	ld	$12, PT_MPL+(0*8)(sp)	/* read MPL0 */
+	ld	$13, PT_MPL+(3*8)(sp)	/* read MPL3 */
+	ld	$10, PT_MPL+(1*8)(sp)	/* read MPL1 */
+	ld	$11, PT_MPL+(4*8)(sp)	/* read MPL4 */
+	.word	0x718d0008
+	/* mtm0	$12, $13		   restore MPL0 and MPL3 */
+	ld	$12, PT_MPL+(2*8)(sp)	/* read MPL2 */
+	.word	0x714b000c
+	/* mtm1	$10, $11		   restore MPL1 and MPL4 */
+	ld	$13, PT_MPL+(5*8)(sp)	/* read MPL5 */
+	ld	$10, PT_MTP+(0*8)(sp)	/* read P0 */
+	ld	$11, PT_MTP+(3*8)(sp)	/* read P3 */
+	.word	0x718d000d
+	/* mtm2	$12, $13		   restore MPL2 and MPL5 */
+	ld	$12, PT_MTP+(1*8)(sp)	/* read P1 */
+	.word	0x714b0009
+	/* mtp0	$10, $11		   restore P0 and P3 */
+	ld	$13, PT_MTP+(4*8)(sp)	/* read P4 */
+	ld	$10, PT_MTP+(2*8)(sp)	/* read P2 */
+	ld	$11, PT_MTP+(5*8)(sp)	/* read P5 */
+	.word	0x718d000a
+	/* mtp1	$12, $13		   restore P1 and P4 */
+	jr	ra
+	.word	0x714b000b
+	/* mtp2	$10, $11		   restore P2 and P5 */
+
+octeon_mult_restore3_end:
+	EXPORT(octeon_mult_restore3_end)
+	END(octeon_mult_restore3)
+	.set pop
diff --git a/arch/mips/kernel/perf_event.c b/arch/mips/kernel/perf_event.c
new file mode 100644
index 000000000..5d7a9c039
--- /dev/null
+++ b/arch/mips/kernel/perf_event.c
@@ -0,0 +1,67 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Linux performance counter support for MIPS.
+ *
+ * Copyright (C) 2010 MIPS Technologies, Inc.
+ * Author: Deng-Cheng Zhu
+ *
+ * This code is based on the implementation for ARM, which is in turn
+ * based on the sparc64 perf event code and the x86 code. Performance
+ * counter access is based on the MIPS Oprofile code. And the callchain
+ * support references the code of MIPS stacktrace.c.
+ */
+
+#include <linux/perf_event.h>
+#include <linux/sched/task_stack.h>
+
+#include <asm/stacktrace.h>
+
+/* Callchain handling code. */
+
+/*
+ * Leave userspace callchain empty for now. When we find a way to trace
+ * the user stack callchains, we will add it here.
+ */
+
+static void save_raw_perf_callchain(struct perf_callchain_entry_ctx *entry,
+				    unsigned long reg29)
+{
+	unsigned long *sp = (unsigned long *)reg29;
+	unsigned long addr;
+
+	while (!kstack_end(sp)) {
+		addr = *sp++;
+		if (__kernel_text_address(addr)) {
+			perf_callchain_store(entry, addr);
+			if (entry->nr >= entry->max_stack)
+				break;
+		}
+	}
+}
+
+void perf_callchain_kernel(struct perf_callchain_entry_ctx *entry,
+			   struct pt_regs *regs)
+{
+	unsigned long sp = regs->regs[29];
+#ifdef CONFIG_KALLSYMS
+	unsigned long ra = regs->regs[31];
+	unsigned long pc = regs->cp0_epc;
+
+	if (raw_show_trace || !__kernel_text_address(pc)) {
+		unsigned long stack_page =
+			(unsigned long)task_stack_page(current);
+		if (stack_page && sp >= stack_page &&
+		    sp <= stack_page + THREAD_SIZE - 32)
+			save_raw_perf_callchain(entry, sp);
+		return;
+	}
+	do {
+		perf_callchain_store(entry, pc);
+		if (entry->nr >= entry->max_stack)
+			break;
+		pc = unwind_stack(current, &sp, pc, &ra);
+	} while (pc);
+#else
+	save_raw_perf_callchain(entry, sp);
+#endif
+}
diff --git a/arch/mips/kernel/perf_event_mipsxx.c b/arch/mips/kernel/perf_event_mipsxx.c
new file mode 100644
index 000000000..c4d6b0913
--- /dev/null
+++ b/arch/mips/kernel/perf_event_mipsxx.c
@@ -0,0 +1,2056 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Linux performance counter support for MIPS.
+ *
+ * Copyright (C) 2010 MIPS Technologies, Inc.
+ * Copyright (C) 2011 Cavium Networks, Inc.
+ * Author: Deng-Cheng Zhu
+ *
+ * This code is based on the implementation for ARM, which is in turn
+ * based on the sparc64 perf event code and the x86 code. Performance
+ * counter access is based on the MIPS Oprofile code. And the callchain
+ * support references the code of MIPS stacktrace.c.
+ */
+
+#include <linux/cpumask.h>
+#include <linux/interrupt.h>
+#include <linux/smp.h>
+#include <linux/kernel.h>
+#include <linux/perf_event.h>
+#include <linux/uaccess.h>
+
+#include <asm/irq.h>
+#include <asm/irq_regs.h>
+#include <asm/stacktrace.h>
+#include <asm/time.h> /* For perf_irq */
+
+#define MIPS_MAX_HWEVENTS 4
+#define MIPS_TCS_PER_COUNTER 2
+#define MIPS_CPUID_TO_COUNTER_MASK (MIPS_TCS_PER_COUNTER - 1)
+
+struct cpu_hw_events {
+	/* Array of events on this cpu. */
+	struct perf_event	*events[MIPS_MAX_HWEVENTS];
+
+	/*
+	 * Set the bit (indexed by the counter number) when the counter
+	 * is used for an event.
+	 */
+	unsigned long		used_mask[BITS_TO_LONGS(MIPS_MAX_HWEVENTS)];
+
+	/*
+	 * Software copy of the control register for each performance counter.
+	 * MIPS CPUs vary in performance counters. They use this differently,
+	 * and even may not use it.
+	 */
+	unsigned int		saved_ctrl[MIPS_MAX_HWEVENTS];
+};
+DEFINE_PER_CPU(struct cpu_hw_events, cpu_hw_events) = {
+	.saved_ctrl = {0},
+};
+
+/* The description of MIPS performance events. */
+struct mips_perf_event {
+	unsigned int event_id;
+	/*
+	 * MIPS performance counters are indexed starting from 0.
+	 * CNTR_EVEN indicates the indexes of the counters to be used are
+	 * even numbers.
+	 */
+	unsigned int cntr_mask;
+	#define CNTR_EVEN	0x55555555
+	#define CNTR_ODD	0xaaaaaaaa
+	#define CNTR_ALL	0xffffffff
+	enum {
+		T  = 0,
+		V  = 1,
+		P  = 2,
+	} range;
+};
+
+static struct mips_perf_event raw_event;
+static DEFINE_MUTEX(raw_event_mutex);
+
+#define C(x) PERF_COUNT_HW_CACHE_##x
+
+struct mips_pmu {
+	u64		max_period;
+	u64		valid_count;
+	u64		overflow;
+	const char	*name;
+	int		irq;
+	u64		(*read_counter)(unsigned int idx);
+	void		(*write_counter)(unsigned int idx, u64 val);
+	const struct mips_perf_event *(*map_raw_event)(u64 config);
+	const struct mips_perf_event (*general_event_map)[PERF_COUNT_HW_MAX];
+	const struct mips_perf_event (*cache_event_map)
+				[PERF_COUNT_HW_CACHE_MAX]
+				[PERF_COUNT_HW_CACHE_OP_MAX]
+				[PERF_COUNT_HW_CACHE_RESULT_MAX];
+	unsigned int	num_counters;
+};
+
+static int counter_bits;
+static struct mips_pmu mipspmu;
+
+#define M_PERFCTL_EVENT(event)		(((event) << MIPS_PERFCTRL_EVENT_S) & \
+					 MIPS_PERFCTRL_EVENT)
+#define M_PERFCTL_VPEID(vpe)		((vpe)	  << MIPS_PERFCTRL_VPEID_S)
+
+#ifdef CONFIG_CPU_BMIPS5000
+#define M_PERFCTL_MT_EN(filter)		0
+#else /* !CONFIG_CPU_BMIPS5000 */
+#define M_PERFCTL_MT_EN(filter)		(filter)
+#endif /* CONFIG_CPU_BMIPS5000 */
+
+#define	   M_TC_EN_ALL			M_PERFCTL_MT_EN(MIPS_PERFCTRL_MT_EN_ALL)
+#define	   M_TC_EN_VPE			M_PERFCTL_MT_EN(MIPS_PERFCTRL_MT_EN_VPE)
+#define	   M_TC_EN_TC			M_PERFCTL_MT_EN(MIPS_PERFCTRL_MT_EN_TC)
+
+#define M_PERFCTL_COUNT_EVENT_WHENEVER	(MIPS_PERFCTRL_EXL |		\
+					 MIPS_PERFCTRL_K |		\
+					 MIPS_PERFCTRL_U |		\
+					 MIPS_PERFCTRL_S |		\
+					 MIPS_PERFCTRL_IE)
+
+#ifdef CONFIG_MIPS_MT_SMP
+#define M_PERFCTL_CONFIG_MASK		0x3fff801f
+#else
+#define M_PERFCTL_CONFIG_MASK		0x1f
+#endif
+
+#define CNTR_BIT_MASK(n)	(((n) == 64) ? ~0ULL : ((1ULL<<(n))-1))
+
+#ifdef CONFIG_MIPS_PERF_SHARED_TC_COUNTERS
+static DEFINE_RWLOCK(pmuint_rwlock);
+
+#if defined(CONFIG_CPU_BMIPS5000)
+#define vpe_id()	(cpu_has_mipsmt_pertccounters ? \
+			 0 : (smp_processor_id() & MIPS_CPUID_TO_COUNTER_MASK))
+#else
+#define vpe_id()	(cpu_has_mipsmt_pertccounters ? \
+			 0 : cpu_vpe_id(&current_cpu_data))
+#endif
+
+/* Copied from op_model_mipsxx.c */
+static unsigned int vpe_shift(void)
+{
+	if (num_possible_cpus() > 1)
+		return 1;
+
+	return 0;
+}
+
+static unsigned int counters_total_to_per_cpu(unsigned int counters)
+{
+	return counters >> vpe_shift();
+}
+
+#else /* !CONFIG_MIPS_PERF_SHARED_TC_COUNTERS */
+#define vpe_id()	0
+
+#endif /* CONFIG_MIPS_PERF_SHARED_TC_COUNTERS */
+
+static void resume_local_counters(void);
+static void pause_local_counters(void);
+static irqreturn_t mipsxx_pmu_handle_irq(int, void *);
+static int mipsxx_pmu_handle_shared_irq(void);
+
+/* 0: Not Loongson-3
+ * 1: Loongson-3A1000/3B1000/3B1500
+ * 2: Loongson-3A2000/3A3000
+ * 3: Loongson-3A4000+
+ */
+
+#define LOONGSON_PMU_TYPE0 0
+#define LOONGSON_PMU_TYPE1 1
+#define LOONGSON_PMU_TYPE2 2
+#define LOONGSON_PMU_TYPE3 3
+
+static inline int get_loongson3_pmu_type(void)
+{
+	if (boot_cpu_type() != CPU_LOONGSON64)
+		return LOONGSON_PMU_TYPE0;
+	if ((boot_cpu_data.processor_id & PRID_COMP_MASK) == PRID_COMP_LEGACY)
+		return LOONGSON_PMU_TYPE1;
+	if ((boot_cpu_data.processor_id & PRID_IMP_MASK) == PRID_IMP_LOONGSON_64C)
+		return LOONGSON_PMU_TYPE2;
+	if ((boot_cpu_data.processor_id & PRID_IMP_MASK) == PRID_IMP_LOONGSON_64G)
+		return LOONGSON_PMU_TYPE3;
+
+	return LOONGSON_PMU_TYPE0;
+}
+
+static unsigned int mipsxx_pmu_swizzle_perf_idx(unsigned int idx)
+{
+	if (vpe_id() == 1)
+		idx = (idx + 2) & 3;
+	return idx;
+}
+
+static u64 mipsxx_pmu_read_counter(unsigned int idx)
+{
+	idx = mipsxx_pmu_swizzle_perf_idx(idx);
+
+	switch (idx) {
+	case 0:
+		/*
+		 * The counters are unsigned, we must cast to truncate
+		 * off the high bits.
+		 */
+		return (u32)read_c0_perfcntr0();
+	case 1:
+		return (u32)read_c0_perfcntr1();
+	case 2:
+		return (u32)read_c0_perfcntr2();
+	case 3:
+		return (u32)read_c0_perfcntr3();
+	default:
+		WARN_ONCE(1, "Invalid performance counter number (%d)\n", idx);
+		return 0;
+	}
+}
+
+static u64 mipsxx_pmu_read_counter_64(unsigned int idx)
+{
+	u64 mask = CNTR_BIT_MASK(counter_bits);
+	idx = mipsxx_pmu_swizzle_perf_idx(idx);
+
+	switch (idx) {
+	case 0:
+		return read_c0_perfcntr0_64() & mask;
+	case 1:
+		return read_c0_perfcntr1_64() & mask;
+	case 2:
+		return read_c0_perfcntr2_64() & mask;
+	case 3:
+		return read_c0_perfcntr3_64() & mask;
+	default:
+		WARN_ONCE(1, "Invalid performance counter number (%d)\n", idx);
+		return 0;
+	}
+}
+
+static void mipsxx_pmu_write_counter(unsigned int idx, u64 val)
+{
+	idx = mipsxx_pmu_swizzle_perf_idx(idx);
+
+	switch (idx) {
+	case 0:
+		write_c0_perfcntr0(val);
+		return;
+	case 1:
+		write_c0_perfcntr1(val);
+		return;
+	case 2:
+		write_c0_perfcntr2(val);
+		return;
+	case 3:
+		write_c0_perfcntr3(val);
+		return;
+	}
+}
+
+static void mipsxx_pmu_write_counter_64(unsigned int idx, u64 val)
+{
+	val &= CNTR_BIT_MASK(counter_bits);
+	idx = mipsxx_pmu_swizzle_perf_idx(idx);
+
+	switch (idx) {
+	case 0:
+		write_c0_perfcntr0_64(val);
+		return;
+	case 1:
+		write_c0_perfcntr1_64(val);
+		return;
+	case 2:
+		write_c0_perfcntr2_64(val);
+		return;
+	case 3:
+		write_c0_perfcntr3_64(val);
+		return;
+	}
+}
+
+static unsigned int mipsxx_pmu_read_control(unsigned int idx)
+{
+	idx = mipsxx_pmu_swizzle_perf_idx(idx);
+
+	switch (idx) {
+	case 0:
+		return read_c0_perfctrl0();
+	case 1:
+		return read_c0_perfctrl1();
+	case 2:
+		return read_c0_perfctrl2();
+	case 3:
+		return read_c0_perfctrl3();
+	default:
+		WARN_ONCE(1, "Invalid performance counter number (%d)\n", idx);
+		return 0;
+	}
+}
+
+static void mipsxx_pmu_write_control(unsigned int idx, unsigned int val)
+{
+	idx = mipsxx_pmu_swizzle_perf_idx(idx);
+
+	switch (idx) {
+	case 0:
+		write_c0_perfctrl0(val);
+		return;
+	case 1:
+		write_c0_perfctrl1(val);
+		return;
+	case 2:
+		write_c0_perfctrl2(val);
+		return;
+	case 3:
+		write_c0_perfctrl3(val);
+		return;
+	}
+}
+
+static int mipsxx_pmu_alloc_counter(struct cpu_hw_events *cpuc,
+				    struct hw_perf_event *hwc)
+{
+	int i;
+	unsigned long cntr_mask;
+
+	/*
+	 * We only need to care the counter mask. The range has been
+	 * checked definitely.
+	 */
+	if (get_loongson3_pmu_type() == LOONGSON_PMU_TYPE2)
+		cntr_mask = (hwc->event_base >> 10) & 0xffff;
+	else
+		cntr_mask = (hwc->event_base >> 8) & 0xffff;
+
+	for (i = mipspmu.num_counters - 1; i >= 0; i--) {
+		/*
+		 * Note that some MIPS perf events can be counted by both
+		 * even and odd counters, whereas many other are only by
+		 * even _or_ odd counters. This introduces an issue that
+		 * when the former kind of event takes the counter the
+		 * latter kind of event wants to use, then the "counter
+		 * allocation" for the latter event will fail. In fact if
+		 * they can be dynamically swapped, they both feel happy.
+		 * But here we leave this issue alone for now.
+		 */
+		if (test_bit(i, &cntr_mask) &&
+			!test_and_set_bit(i, cpuc->used_mask))
+			return i;
+	}
+
+	return -EAGAIN;
+}
+
+static void mipsxx_pmu_enable_event(struct hw_perf_event *evt, int idx)
+{
+	struct perf_event *event = container_of(evt, struct perf_event, hw);
+	struct cpu_hw_events *cpuc = this_cpu_ptr(&cpu_hw_events);
+	unsigned int range = evt->event_base >> 24;
+
+	WARN_ON(idx < 0 || idx >= mipspmu.num_counters);
+
+	if (get_loongson3_pmu_type() == LOONGSON_PMU_TYPE2)
+		cpuc->saved_ctrl[idx] = M_PERFCTL_EVENT(evt->event_base & 0x3ff) |
+			(evt->config_base & M_PERFCTL_CONFIG_MASK) |
+			/* Make sure interrupt enabled. */
+			MIPS_PERFCTRL_IE;
+	else
+		cpuc->saved_ctrl[idx] = M_PERFCTL_EVENT(evt->event_base & 0xff) |
+			(evt->config_base & M_PERFCTL_CONFIG_MASK) |
+			/* Make sure interrupt enabled. */
+			MIPS_PERFCTRL_IE;
+
+	if (IS_ENABLED(CONFIG_CPU_BMIPS5000)) {
+		/* enable the counter for the calling thread */
+		cpuc->saved_ctrl[idx] |=
+			(1 << (12 + vpe_id())) | BRCM_PERFCTRL_TC;
+	} else if (IS_ENABLED(CONFIG_MIPS_MT_SMP) && range > V) {
+		/* The counter is processor wide. Set it up to count all TCs. */
+		pr_debug("Enabling perf counter for all TCs\n");
+		cpuc->saved_ctrl[idx] |= M_TC_EN_ALL;
+	} else {
+		unsigned int cpu, ctrl;
+
+		/*
+		 * Set up the counter for a particular CPU when event->cpu is
+		 * a valid CPU number. Otherwise set up the counter for the CPU
+		 * scheduling this thread.
+		 */
+		cpu = (event->cpu >= 0) ? event->cpu : smp_processor_id();
+
+		ctrl = M_PERFCTL_VPEID(cpu_vpe_id(&cpu_data[cpu]));
+		ctrl |= M_TC_EN_VPE;
+		cpuc->saved_ctrl[idx] |= ctrl;
+		pr_debug("Enabling perf counter for CPU%d\n", cpu);
+	}
+	/*
+	 * We do not actually let the counter run. Leave it until start().
+	 */
+}
+
+static void mipsxx_pmu_disable_event(int idx)
+{
+	struct cpu_hw_events *cpuc = this_cpu_ptr(&cpu_hw_events);
+	unsigned long flags;
+
+	WARN_ON(idx < 0 || idx >= mipspmu.num_counters);
+
+	local_irq_save(flags);
+	cpuc->saved_ctrl[idx] = mipsxx_pmu_read_control(idx) &
+		~M_PERFCTL_COUNT_EVENT_WHENEVER;
+	mipsxx_pmu_write_control(idx, cpuc->saved_ctrl[idx]);
+	local_irq_restore(flags);
+}
+
+static int mipspmu_event_set_period(struct perf_event *event,
+				    struct hw_perf_event *hwc,
+				    int idx)
+{
+	u64 left = local64_read(&hwc->period_left);
+	u64 period = hwc->sample_period;
+	int ret = 0;
+
+	if (unlikely((left + period) & (1ULL << 63))) {
+		/* left underflowed by more than period. */
+		left = period;
+		local64_set(&hwc->period_left, left);
+		hwc->last_period = period;
+		ret = 1;
+	} else	if (unlikely((left + period) <= period)) {
+		/* left underflowed by less than period. */
+		left += period;
+		local64_set(&hwc->period_left, left);
+		hwc->last_period = period;
+		ret = 1;
+	}
+
+	if (left > mipspmu.max_period) {
+		left = mipspmu.max_period;
+		local64_set(&hwc->period_left, left);
+	}
+
+	local64_set(&hwc->prev_count, mipspmu.overflow - left);
+
+	if (get_loongson3_pmu_type() == LOONGSON_PMU_TYPE2)
+		mipsxx_pmu_write_control(idx,
+				M_PERFCTL_EVENT(hwc->event_base & 0x3ff));
+
+	mipspmu.write_counter(idx, mipspmu.overflow - left);
+
+	perf_event_update_userpage(event);
+
+	return ret;
+}
+
+static void mipspmu_event_update(struct perf_event *event,
+				 struct hw_perf_event *hwc,
+				 int idx)
+{
+	u64 prev_raw_count, new_raw_count;
+	u64 delta;
+
+again:
+	prev_raw_count = local64_read(&hwc->prev_count);
+	new_raw_count = mipspmu.read_counter(idx);
+
+	if (local64_cmpxchg(&hwc->prev_count, prev_raw_count,
+				new_raw_count) != prev_raw_count)
+		goto again;
+
+	delta = new_raw_count - prev_raw_count;
+
+	local64_add(delta, &event->count);
+	local64_sub(delta, &hwc->period_left);
+}
+
+static void mipspmu_start(struct perf_event *event, int flags)
+{
+	struct hw_perf_event *hwc = &event->hw;
+
+	if (flags & PERF_EF_RELOAD)
+		WARN_ON_ONCE(!(hwc->state & PERF_HES_UPTODATE));
+
+	hwc->state = 0;
+
+	/* Set the period for the event. */
+	mipspmu_event_set_period(event, hwc, hwc->idx);
+
+	/* Enable the event. */
+	mipsxx_pmu_enable_event(hwc, hwc->idx);
+}
+
+static void mipspmu_stop(struct perf_event *event, int flags)
+{
+	struct hw_perf_event *hwc = &event->hw;
+
+	if (!(hwc->state & PERF_HES_STOPPED)) {
+		/* We are working on a local event. */
+		mipsxx_pmu_disable_event(hwc->idx);
+		barrier();
+		mipspmu_event_update(event, hwc, hwc->idx);
+		hwc->state |= PERF_HES_STOPPED | PERF_HES_UPTODATE;
+	}
+}
+
+static int mipspmu_add(struct perf_event *event, int flags)
+{
+	struct cpu_hw_events *cpuc = this_cpu_ptr(&cpu_hw_events);
+	struct hw_perf_event *hwc = &event->hw;
+	int idx;
+	int err = 0;
+
+	perf_pmu_disable(event->pmu);
+
+	/* To look for a free counter for this event. */
+	idx = mipsxx_pmu_alloc_counter(cpuc, hwc);
+	if (idx < 0) {
+		err = idx;
+		goto out;
+	}
+
+	/*
+	 * If there is an event in the counter we are going to use then
+	 * make sure it is disabled.
+	 */
+	event->hw.idx = idx;
+	mipsxx_pmu_disable_event(idx);
+	cpuc->events[idx] = event;
+
+	hwc->state = PERF_HES_STOPPED | PERF_HES_UPTODATE;
+	if (flags & PERF_EF_START)
+		mipspmu_start(event, PERF_EF_RELOAD);
+
+	/* Propagate our changes to the userspace mapping. */
+	perf_event_update_userpage(event);
+
+out:
+	perf_pmu_enable(event->pmu);
+	return err;
+}
+
+static void mipspmu_del(struct perf_event *event, int flags)
+{
+	struct cpu_hw_events *cpuc = this_cpu_ptr(&cpu_hw_events);
+	struct hw_perf_event *hwc = &event->hw;
+	int idx = hwc->idx;
+
+	WARN_ON(idx < 0 || idx >= mipspmu.num_counters);
+
+	mipspmu_stop(event, PERF_EF_UPDATE);
+	cpuc->events[idx] = NULL;
+	clear_bit(idx, cpuc->used_mask);
+
+	perf_event_update_userpage(event);
+}
+
+static void mipspmu_read(struct perf_event *event)
+{
+	struct hw_perf_event *hwc = &event->hw;
+
+	/* Don't read disabled counters! */
+	if (hwc->idx < 0)
+		return;
+
+	mipspmu_event_update(event, hwc, hwc->idx);
+}
+
+static void mipspmu_enable(struct pmu *pmu)
+{
+#ifdef CONFIG_MIPS_PERF_SHARED_TC_COUNTERS
+	write_unlock(&pmuint_rwlock);
+#endif
+	resume_local_counters();
+}
+
+/*
+ * MIPS performance counters can be per-TC. The control registers can
+ * not be directly accessed across CPUs. Hence if we want to do global
+ * control, we need cross CPU calls. on_each_cpu() can help us, but we
+ * can not make sure this function is called with interrupts enabled. So
+ * here we pause local counters and then grab a rwlock and leave the
+ * counters on other CPUs alone. If any counter interrupt raises while
+ * we own the write lock, simply pause local counters on that CPU and
+ * spin in the handler. Also we know we won't be switched to another
+ * CPU after pausing local counters and before grabbing the lock.
+ */
+static void mipspmu_disable(struct pmu *pmu)
+{
+	pause_local_counters();
+#ifdef CONFIG_MIPS_PERF_SHARED_TC_COUNTERS
+	write_lock(&pmuint_rwlock);
+#endif
+}
+
+static atomic_t active_events = ATOMIC_INIT(0);
+static DEFINE_MUTEX(pmu_reserve_mutex);
+static int (*save_perf_irq)(void);
+
+static int mipspmu_get_irq(void)
+{
+	int err;
+
+	if (mipspmu.irq >= 0) {
+		/* Request my own irq handler. */
+		err = request_irq(mipspmu.irq, mipsxx_pmu_handle_irq,
+				  IRQF_PERCPU | IRQF_NOBALANCING |
+				  IRQF_NO_THREAD | IRQF_NO_SUSPEND |
+				  IRQF_SHARED,
+				  "mips_perf_pmu", &mipspmu);
+		if (err) {
+			pr_warn("Unable to request IRQ%d for MIPS performance counters!\n",
+				mipspmu.irq);
+		}
+	} else if (cp0_perfcount_irq < 0) {
+		/*
+		 * We are sharing the irq number with the timer interrupt.
+		 */
+		save_perf_irq = perf_irq;
+		perf_irq = mipsxx_pmu_handle_shared_irq;
+		err = 0;
+	} else {
+		pr_warn("The platform hasn't properly defined its interrupt controller\n");
+		err = -ENOENT;
+	}
+
+	return err;
+}
+
+static void mipspmu_free_irq(void)
+{
+	if (mipspmu.irq >= 0)
+		free_irq(mipspmu.irq, &mipspmu);
+	else if (cp0_perfcount_irq < 0)
+		perf_irq = save_perf_irq;
+}
+
+/*
+ * mipsxx/rm9000/loongson2 have different performance counters, they have
+ * specific low-level init routines.
+ */
+static void reset_counters(void *arg);
+static int __hw_perf_event_init(struct perf_event *event);
+
+static void hw_perf_event_destroy(struct perf_event *event)
+{
+	if (atomic_dec_and_mutex_lock(&active_events,
+				&pmu_reserve_mutex)) {
+		/*
+		 * We must not call the destroy function with interrupts
+		 * disabled.
+		 */
+		on_each_cpu(reset_counters,
+			(void *)(long)mipspmu.num_counters, 1);
+		mipspmu_free_irq();
+		mutex_unlock(&pmu_reserve_mutex);
+	}
+}
+
+static int mipspmu_event_init(struct perf_event *event)
+{
+	int err = 0;
+
+	/* does not support taken branch sampling */
+	if (has_branch_stack(event))
+		return -EOPNOTSUPP;
+
+	switch (event->attr.type) {
+	case PERF_TYPE_RAW:
+	case PERF_TYPE_HARDWARE:
+	case PERF_TYPE_HW_CACHE:
+		break;
+
+	default:
+		return -ENOENT;
+	}
+
+	if (event->cpu >= 0 && !cpu_online(event->cpu))
+		return -ENODEV;
+
+	if (!atomic_inc_not_zero(&active_events)) {
+		mutex_lock(&pmu_reserve_mutex);
+		if (atomic_read(&active_events) == 0)
+			err = mipspmu_get_irq();
+
+		if (!err)
+			atomic_inc(&active_events);
+		mutex_unlock(&pmu_reserve_mutex);
+	}
+
+	if (err)
+		return err;
+
+	return __hw_perf_event_init(event);
+}
+
+static struct pmu pmu = {
+	.pmu_enable	= mipspmu_enable,
+	.pmu_disable	= mipspmu_disable,
+	.event_init	= mipspmu_event_init,
+	.add		= mipspmu_add,
+	.del		= mipspmu_del,
+	.start		= mipspmu_start,
+	.stop		= mipspmu_stop,
+	.read		= mipspmu_read,
+};
+
+static unsigned int mipspmu_perf_event_encode(const struct mips_perf_event *pev)
+{
+/*
+ * Top 8 bits for range, next 16 bits for cntr_mask, lowest 8 bits for
+ * event_id.
+ */
+#ifdef CONFIG_MIPS_MT_SMP
+	if (num_possible_cpus() > 1)
+		return ((unsigned int)pev->range << 24) |
+			(pev->cntr_mask & 0xffff00) |
+			(pev->event_id & 0xff);
+	else
+#endif /* CONFIG_MIPS_MT_SMP */
+	{
+		if (get_loongson3_pmu_type() == LOONGSON_PMU_TYPE2)
+			return (pev->cntr_mask & 0xfffc00) |
+				(pev->event_id & 0x3ff);
+		else
+			return (pev->cntr_mask & 0xffff00) |
+				(pev->event_id & 0xff);
+	}
+}
+
+static const struct mips_perf_event *mipspmu_map_general_event(int idx)
+{
+
+	if ((*mipspmu.general_event_map)[idx].cntr_mask == 0)
+		return ERR_PTR(-EOPNOTSUPP);
+	return &(*mipspmu.general_event_map)[idx];
+}
+
+static const struct mips_perf_event *mipspmu_map_cache_event(u64 config)
+{
+	unsigned int cache_type, cache_op, cache_result;
+	const struct mips_perf_event *pev;
+
+	cache_type = (config >> 0) & 0xff;
+	if (cache_type >= PERF_COUNT_HW_CACHE_MAX)
+		return ERR_PTR(-EINVAL);
+
+	cache_op = (config >> 8) & 0xff;
+	if (cache_op >= PERF_COUNT_HW_CACHE_OP_MAX)
+		return ERR_PTR(-EINVAL);
+
+	cache_result = (config >> 16) & 0xff;
+	if (cache_result >= PERF_COUNT_HW_CACHE_RESULT_MAX)
+		return ERR_PTR(-EINVAL);
+
+	pev = &((*mipspmu.cache_event_map)
+					[cache_type]
+					[cache_op]
+					[cache_result]);
+
+	if (pev->cntr_mask == 0)
+		return ERR_PTR(-EOPNOTSUPP);
+
+	return pev;
+
+}
+
+static int validate_group(struct perf_event *event)
+{
+	struct perf_event *sibling, *leader = event->group_leader;
+	struct cpu_hw_events fake_cpuc;
+
+	memset(&fake_cpuc, 0, sizeof(fake_cpuc));
+
+	if (mipsxx_pmu_alloc_counter(&fake_cpuc, &leader->hw) < 0)
+		return -EINVAL;
+
+	for_each_sibling_event(sibling, leader) {
+		if (mipsxx_pmu_alloc_counter(&fake_cpuc, &sibling->hw) < 0)
+			return -EINVAL;
+	}
+
+	if (mipsxx_pmu_alloc_counter(&fake_cpuc, &event->hw) < 0)
+		return -EINVAL;
+
+	return 0;
+}
+
+/* This is needed by specific irq handlers in perf_event_*.c */
+static void handle_associated_event(struct cpu_hw_events *cpuc,
+				    int idx, struct perf_sample_data *data,
+				    struct pt_regs *regs)
+{
+	struct perf_event *event = cpuc->events[idx];
+	struct hw_perf_event *hwc = &event->hw;
+
+	mipspmu_event_update(event, hwc, idx);
+	data->period = event->hw.last_period;
+	if (!mipspmu_event_set_period(event, hwc, idx))
+		return;
+
+	if (perf_event_overflow(event, data, regs))
+		mipsxx_pmu_disable_event(idx);
+}
+
+
+static int __n_counters(void)
+{
+	if (!cpu_has_perf)
+		return 0;
+	if (!(read_c0_perfctrl0() & MIPS_PERFCTRL_M))
+		return 1;
+	if (!(read_c0_perfctrl1() & MIPS_PERFCTRL_M))
+		return 2;
+	if (!(read_c0_perfctrl2() & MIPS_PERFCTRL_M))
+		return 3;
+
+	return 4;
+}
+
+static int n_counters(void)
+{
+	int counters;
+
+	switch (current_cpu_type()) {
+	case CPU_R10000:
+		counters = 2;
+		break;
+
+	case CPU_R12000:
+	case CPU_R14000:
+	case CPU_R16000:
+		counters = 4;
+		break;
+
+	default:
+		counters = __n_counters();
+	}
+
+	return counters;
+}
+
+static void loongson3_reset_counters(void *arg)
+{
+	int counters = (int)(long)arg;
+
+	switch (counters) {
+	case 4:
+		mipsxx_pmu_write_control(3, 0);
+		mipspmu.write_counter(3, 0);
+		mipsxx_pmu_write_control(3, 127<<5);
+		mipspmu.write_counter(3, 0);
+		mipsxx_pmu_write_control(3, 191<<5);
+		mipspmu.write_counter(3, 0);
+		mipsxx_pmu_write_control(3, 255<<5);
+		mipspmu.write_counter(3, 0);
+		mipsxx_pmu_write_control(3, 319<<5);
+		mipspmu.write_counter(3, 0);
+		mipsxx_pmu_write_control(3, 383<<5);
+		mipspmu.write_counter(3, 0);
+		mipsxx_pmu_write_control(3, 575<<5);
+		mipspmu.write_counter(3, 0);
+		fallthrough;
+	case 3:
+		mipsxx_pmu_write_control(2, 0);
+		mipspmu.write_counter(2, 0);
+		mipsxx_pmu_write_control(2, 127<<5);
+		mipspmu.write_counter(2, 0);
+		mipsxx_pmu_write_control(2, 191<<5);
+		mipspmu.write_counter(2, 0);
+		mipsxx_pmu_write_control(2, 255<<5);
+		mipspmu.write_counter(2, 0);
+		mipsxx_pmu_write_control(2, 319<<5);
+		mipspmu.write_counter(2, 0);
+		mipsxx_pmu_write_control(2, 383<<5);
+		mipspmu.write_counter(2, 0);
+		mipsxx_pmu_write_control(2, 575<<5);
+		mipspmu.write_counter(2, 0);
+		fallthrough;
+	case 2:
+		mipsxx_pmu_write_control(1, 0);
+		mipspmu.write_counter(1, 0);
+		mipsxx_pmu_write_control(1, 127<<5);
+		mipspmu.write_counter(1, 0);
+		mipsxx_pmu_write_control(1, 191<<5);
+		mipspmu.write_counter(1, 0);
+		mipsxx_pmu_write_control(1, 255<<5);
+		mipspmu.write_counter(1, 0);
+		mipsxx_pmu_write_control(1, 319<<5);
+		mipspmu.write_counter(1, 0);
+		mipsxx_pmu_write_control(1, 383<<5);
+		mipspmu.write_counter(1, 0);
+		mipsxx_pmu_write_control(1, 575<<5);
+		mipspmu.write_counter(1, 0);
+		fallthrough;
+	case 1:
+		mipsxx_pmu_write_control(0, 0);
+		mipspmu.write_counter(0, 0);
+		mipsxx_pmu_write_control(0, 127<<5);
+		mipspmu.write_counter(0, 0);
+		mipsxx_pmu_write_control(0, 191<<5);
+		mipspmu.write_counter(0, 0);
+		mipsxx_pmu_write_control(0, 255<<5);
+		mipspmu.write_counter(0, 0);
+		mipsxx_pmu_write_control(0, 319<<5);
+		mipspmu.write_counter(0, 0);
+		mipsxx_pmu_write_control(0, 383<<5);
+		mipspmu.write_counter(0, 0);
+		mipsxx_pmu_write_control(0, 575<<5);
+		mipspmu.write_counter(0, 0);
+		break;
+	}
+}
+
+static void reset_counters(void *arg)
+{
+	int counters = (int)(long)arg;
+
+	if (get_loongson3_pmu_type() == LOONGSON_PMU_TYPE2) {
+		loongson3_reset_counters(arg);
+		return;
+	}
+
+	switch (counters) {
+	case 4:
+		mipsxx_pmu_write_control(3, 0);
+		mipspmu.write_counter(3, 0);
+		fallthrough;
+	case 3:
+		mipsxx_pmu_write_control(2, 0);
+		mipspmu.write_counter(2, 0);
+		fallthrough;
+	case 2:
+		mipsxx_pmu_write_control(1, 0);
+		mipspmu.write_counter(1, 0);
+		fallthrough;
+	case 1:
+		mipsxx_pmu_write_control(0, 0);
+		mipspmu.write_counter(0, 0);
+		break;
+	}
+}
+
+/* 24K/34K/1004K/interAptiv/loongson1 cores share the same event map. */
+static const struct mips_perf_event mipsxxcore_event_map
+				[PERF_COUNT_HW_MAX] = {
+	[PERF_COUNT_HW_CPU_CYCLES] = { 0x00, CNTR_EVEN | CNTR_ODD, P },
+	[PERF_COUNT_HW_INSTRUCTIONS] = { 0x01, CNTR_EVEN | CNTR_ODD, T },
+	[PERF_COUNT_HW_BRANCH_INSTRUCTIONS] = { 0x02, CNTR_EVEN, T },
+	[PERF_COUNT_HW_BRANCH_MISSES] = { 0x02, CNTR_ODD, T },
+};
+
+/* 74K/proAptiv core has different branch event code. */
+static const struct mips_perf_event mipsxxcore_event_map2
+				[PERF_COUNT_HW_MAX] = {
+	[PERF_COUNT_HW_CPU_CYCLES] = { 0x00, CNTR_EVEN | CNTR_ODD, P },
+	[PERF_COUNT_HW_INSTRUCTIONS] = { 0x01, CNTR_EVEN | CNTR_ODD, T },
+	[PERF_COUNT_HW_BRANCH_INSTRUCTIONS] = { 0x27, CNTR_EVEN, T },
+	[PERF_COUNT_HW_BRANCH_MISSES] = { 0x27, CNTR_ODD, T },
+};
+
+static const struct mips_perf_event i6x00_event_map[PERF_COUNT_HW_MAX] = {
+	[PERF_COUNT_HW_CPU_CYCLES]          = { 0x00, CNTR_EVEN | CNTR_ODD },
+	[PERF_COUNT_HW_INSTRUCTIONS]        = { 0x01, CNTR_EVEN | CNTR_ODD },
+	/* These only count dcache, not icache */
+	[PERF_COUNT_HW_CACHE_REFERENCES]    = { 0x45, CNTR_EVEN | CNTR_ODD },
+	[PERF_COUNT_HW_CACHE_MISSES]        = { 0x48, CNTR_EVEN | CNTR_ODD },
+	[PERF_COUNT_HW_BRANCH_INSTRUCTIONS] = { 0x15, CNTR_EVEN | CNTR_ODD },
+	[PERF_COUNT_HW_BRANCH_MISSES]       = { 0x16, CNTR_EVEN | CNTR_ODD },
+};
+
+static const struct mips_perf_event loongson3_event_map1[PERF_COUNT_HW_MAX] = {
+	[PERF_COUNT_HW_CPU_CYCLES] = { 0x00, CNTR_EVEN },
+	[PERF_COUNT_HW_INSTRUCTIONS] = { 0x00, CNTR_ODD },
+	[PERF_COUNT_HW_BRANCH_INSTRUCTIONS] = { 0x01, CNTR_EVEN },
+	[PERF_COUNT_HW_BRANCH_MISSES] = { 0x01, CNTR_ODD },
+};
+
+static const struct mips_perf_event loongson3_event_map2[PERF_COUNT_HW_MAX] = {
+	[PERF_COUNT_HW_CPU_CYCLES] = { 0x80, CNTR_ALL },
+	[PERF_COUNT_HW_INSTRUCTIONS] = { 0x81, CNTR_ALL },
+	[PERF_COUNT_HW_CACHE_MISSES] = { 0x18, CNTR_ALL },
+	[PERF_COUNT_HW_BRANCH_INSTRUCTIONS] = { 0x94, CNTR_ALL },
+	[PERF_COUNT_HW_BRANCH_MISSES] = { 0x9c, CNTR_ALL },
+};
+
+static const struct mips_perf_event loongson3_event_map3[PERF_COUNT_HW_MAX] = {
+	[PERF_COUNT_HW_CPU_CYCLES] = { 0x00, CNTR_ALL },
+	[PERF_COUNT_HW_INSTRUCTIONS] = { 0x01, CNTR_ALL },
+	[PERF_COUNT_HW_CACHE_REFERENCES] = { 0x1c, CNTR_ALL },
+	[PERF_COUNT_HW_CACHE_MISSES] = { 0x1d, CNTR_ALL },
+	[PERF_COUNT_HW_BRANCH_INSTRUCTIONS] = { 0x02, CNTR_ALL },
+	[PERF_COUNT_HW_BRANCH_MISSES] = { 0x08, CNTR_ALL },
+};
+
+static const struct mips_perf_event octeon_event_map[PERF_COUNT_HW_MAX] = {
+	[PERF_COUNT_HW_CPU_CYCLES] = { 0x01, CNTR_ALL },
+	[PERF_COUNT_HW_INSTRUCTIONS] = { 0x03, CNTR_ALL },
+	[PERF_COUNT_HW_CACHE_REFERENCES] = { 0x2b, CNTR_ALL },
+	[PERF_COUNT_HW_CACHE_MISSES] = { 0x2e, CNTR_ALL	 },
+	[PERF_COUNT_HW_BRANCH_INSTRUCTIONS] = { 0x08, CNTR_ALL },
+	[PERF_COUNT_HW_BRANCH_MISSES] = { 0x09, CNTR_ALL },
+	[PERF_COUNT_HW_BUS_CYCLES] = { 0x25, CNTR_ALL },
+};
+
+static const struct mips_perf_event bmips5000_event_map
+				[PERF_COUNT_HW_MAX] = {
+	[PERF_COUNT_HW_CPU_CYCLES] = { 0x00, CNTR_EVEN | CNTR_ODD, T },
+	[PERF_COUNT_HW_INSTRUCTIONS] = { 0x01, CNTR_EVEN | CNTR_ODD, T },
+	[PERF_COUNT_HW_BRANCH_MISSES] = { 0x02, CNTR_ODD, T },
+};
+
+/* 24K/34K/1004K/interAptiv/loongson1 cores share the same cache event map. */
+static const struct mips_perf_event mipsxxcore_cache_map
+				[PERF_COUNT_HW_CACHE_MAX]
+				[PERF_COUNT_HW_CACHE_OP_MAX]
+				[PERF_COUNT_HW_CACHE_RESULT_MAX] = {
+[C(L1D)] = {
+	/*
+	 * Like some other architectures (e.g. ARM), the performance
+	 * counters don't differentiate between read and write
+	 * accesses/misses, so this isn't strictly correct, but it's the
+	 * best we can do. Writes and reads get combined.
+	 */
+	[C(OP_READ)] = {
+		[C(RESULT_ACCESS)]	= { 0x0a, CNTR_EVEN, T },
+		[C(RESULT_MISS)]	= { 0x0b, CNTR_EVEN | CNTR_ODD, T },
+	},
+	[C(OP_WRITE)] = {
+		[C(RESULT_ACCESS)]	= { 0x0a, CNTR_EVEN, T },
+		[C(RESULT_MISS)]	= { 0x0b, CNTR_EVEN | CNTR_ODD, T },
+	},
+},
+[C(L1I)] = {
+	[C(OP_READ)] = {
+		[C(RESULT_ACCESS)]	= { 0x09, CNTR_EVEN, T },
+		[C(RESULT_MISS)]	= { 0x09, CNTR_ODD, T },
+	},
+	[C(OP_WRITE)] = {
+		[C(RESULT_ACCESS)]	= { 0x09, CNTR_EVEN, T },
+		[C(RESULT_MISS)]	= { 0x09, CNTR_ODD, T },
+	},
+	[C(OP_PREFETCH)] = {
+		[C(RESULT_ACCESS)]	= { 0x14, CNTR_EVEN, T },
+		/*
+		 * Note that MIPS has only "hit" events countable for
+		 * the prefetch operation.
+		 */
+	},
+},
+[C(LL)] = {
+	[C(OP_READ)] = {
+		[C(RESULT_ACCESS)]	= { 0x15, CNTR_ODD, P },
+		[C(RESULT_MISS)]	= { 0x16, CNTR_EVEN, P },
+	},
+	[C(OP_WRITE)] = {
+		[C(RESULT_ACCESS)]	= { 0x15, CNTR_ODD, P },
+		[C(RESULT_MISS)]	= { 0x16, CNTR_EVEN, P },
+	},
+},
+[C(DTLB)] = {
+	[C(OP_READ)] = {
+		[C(RESULT_ACCESS)]	= { 0x06, CNTR_EVEN, T },
+		[C(RESULT_MISS)]	= { 0x06, CNTR_ODD, T },
+	},
+	[C(OP_WRITE)] = {
+		[C(RESULT_ACCESS)]	= { 0x06, CNTR_EVEN, T },
+		[C(RESULT_MISS)]	= { 0x06, CNTR_ODD, T },
+	},
+},
+[C(ITLB)] = {
+	[C(OP_READ)] = {
+		[C(RESULT_ACCESS)]	= { 0x05, CNTR_EVEN, T },
+		[C(RESULT_MISS)]	= { 0x05, CNTR_ODD, T },
+	},
+	[C(OP_WRITE)] = {
+		[C(RESULT_ACCESS)]	= { 0x05, CNTR_EVEN, T },
+		[C(RESULT_MISS)]	= { 0x05, CNTR_ODD, T },
+	},
+},
+[C(BPU)] = {
+	/* Using the same code for *HW_BRANCH* */
+	[C(OP_READ)] = {
+		[C(RESULT_ACCESS)]	= { 0x02, CNTR_EVEN, T },
+		[C(RESULT_MISS)]	= { 0x02, CNTR_ODD, T },
+	},
+	[C(OP_WRITE)] = {
+		[C(RESULT_ACCESS)]	= { 0x02, CNTR_EVEN, T },
+		[C(RESULT_MISS)]	= { 0x02, CNTR_ODD, T },
+	},
+},
+};
+
+/* 74K/proAptiv core has completely different cache event map. */
+static const struct mips_perf_event mipsxxcore_cache_map2
+				[PERF_COUNT_HW_CACHE_MAX]
+				[PERF_COUNT_HW_CACHE_OP_MAX]
+				[PERF_COUNT_HW_CACHE_RESULT_MAX] = {
+[C(L1D)] = {
+	/*
+	 * Like some other architectures (e.g. ARM), the performance
+	 * counters don't differentiate between read and write
+	 * accesses/misses, so this isn't strictly correct, but it's the
+	 * best we can do. Writes and reads get combined.
+	 */
+	[C(OP_READ)] = {
+		[C(RESULT_ACCESS)]	= { 0x17, CNTR_ODD, T },
+		[C(RESULT_MISS)]	= { 0x18, CNTR_ODD, T },
+	},
+	[C(OP_WRITE)] = {
+		[C(RESULT_ACCESS)]	= { 0x17, CNTR_ODD, T },
+		[C(RESULT_MISS)]	= { 0x18, CNTR_ODD, T },
+	},
+},
+[C(L1I)] = {
+	[C(OP_READ)] = {
+		[C(RESULT_ACCESS)]	= { 0x06, CNTR_EVEN, T },
+		[C(RESULT_MISS)]	= { 0x06, CNTR_ODD, T },
+	},
+	[C(OP_WRITE)] = {
+		[C(RESULT_ACCESS)]	= { 0x06, CNTR_EVEN, T },
+		[C(RESULT_MISS)]	= { 0x06, CNTR_ODD, T },
+	},
+	[C(OP_PREFETCH)] = {
+		[C(RESULT_ACCESS)]	= { 0x34, CNTR_EVEN, T },
+		/*
+		 * Note that MIPS has only "hit" events countable for
+		 * the prefetch operation.
+		 */
+	},
+},
+[C(LL)] = {
+	[C(OP_READ)] = {
+		[C(RESULT_ACCESS)]	= { 0x1c, CNTR_ODD, P },
+		[C(RESULT_MISS)]	= { 0x1d, CNTR_EVEN, P },
+	},
+	[C(OP_WRITE)] = {
+		[C(RESULT_ACCESS)]	= { 0x1c, CNTR_ODD, P },
+		[C(RESULT_MISS)]	= { 0x1d, CNTR_EVEN, P },
+	},
+},
+/*
+ * 74K core does not have specific DTLB events. proAptiv core has
+ * "speculative" DTLB events which are numbered 0x63 (even/odd) and
+ * not included here. One can use raw events if really needed.
+ */
+[C(ITLB)] = {
+	[C(OP_READ)] = {
+		[C(RESULT_ACCESS)]	= { 0x04, CNTR_EVEN, T },
+		[C(RESULT_MISS)]	= { 0x04, CNTR_ODD, T },
+	},
+	[C(OP_WRITE)] = {
+		[C(RESULT_ACCESS)]	= { 0x04, CNTR_EVEN, T },
+		[C(RESULT_MISS)]	= { 0x04, CNTR_ODD, T },
+	},
+},
+[C(BPU)] = {
+	/* Using the same code for *HW_BRANCH* */
+	[C(OP_READ)] = {
+		[C(RESULT_ACCESS)]	= { 0x27, CNTR_EVEN, T },
+		[C(RESULT_MISS)]	= { 0x27, CNTR_ODD, T },
+	},
+	[C(OP_WRITE)] = {
+		[C(RESULT_ACCESS)]	= { 0x27, CNTR_EVEN, T },
+		[C(RESULT_MISS)]	= { 0x27, CNTR_ODD, T },
+	},
+},
+};
+
+static const struct mips_perf_event i6x00_cache_map
+				[PERF_COUNT_HW_CACHE_MAX]
+				[PERF_COUNT_HW_CACHE_OP_MAX]
+				[PERF_COUNT_HW_CACHE_RESULT_MAX] = {
+[C(L1D)] = {
+	[C(OP_READ)] = {
+		[C(RESULT_ACCESS)]	= { 0x46, CNTR_EVEN | CNTR_ODD },
+		[C(RESULT_MISS)]	= { 0x49, CNTR_EVEN | CNTR_ODD },
+	},
+	[C(OP_WRITE)] = {
+		[C(RESULT_ACCESS)]	= { 0x47, CNTR_EVEN | CNTR_ODD },
+		[C(RESULT_MISS)]	= { 0x4a, CNTR_EVEN | CNTR_ODD },
+	},
+},
+[C(L1I)] = {
+	[C(OP_READ)] = {
+		[C(RESULT_ACCESS)]	= { 0x84, CNTR_EVEN | CNTR_ODD },
+		[C(RESULT_MISS)]	= { 0x85, CNTR_EVEN | CNTR_ODD },
+	},
+},
+[C(DTLB)] = {
+	/* Can't distinguish read & write */
+	[C(OP_READ)] = {
+		[C(RESULT_ACCESS)]	= { 0x40, CNTR_EVEN | CNTR_ODD },
+		[C(RESULT_MISS)]	= { 0x41, CNTR_EVEN | CNTR_ODD },
+	},
+	[C(OP_WRITE)] = {
+		[C(RESULT_ACCESS)]	= { 0x40, CNTR_EVEN | CNTR_ODD },
+		[C(RESULT_MISS)]	= { 0x41, CNTR_EVEN | CNTR_ODD },
+	},
+},
+[C(BPU)] = {
+	/* Conditional branches / mispredicted */
+	[C(OP_READ)] = {
+		[C(RESULT_ACCESS)]	= { 0x15, CNTR_EVEN | CNTR_ODD },
+		[C(RESULT_MISS)]	= { 0x16, CNTR_EVEN | CNTR_ODD },
+	},
+},
+};
+
+static const struct mips_perf_event loongson3_cache_map1
+				[PERF_COUNT_HW_CACHE_MAX]
+				[PERF_COUNT_HW_CACHE_OP_MAX]
+				[PERF_COUNT_HW_CACHE_RESULT_MAX] = {
+[C(L1D)] = {
+	/*
+	 * Like some other architectures (e.g. ARM), the performance
+	 * counters don't differentiate between read and write
+	 * accesses/misses, so this isn't strictly correct, but it's the
+	 * best we can do. Writes and reads get combined.
+	 */
+	[C(OP_READ)] = {
+		[C(RESULT_MISS)]        = { 0x04, CNTR_ODD },
+	},
+	[C(OP_WRITE)] = {
+		[C(RESULT_MISS)]        = { 0x04, CNTR_ODD },
+	},
+},
+[C(L1I)] = {
+	[C(OP_READ)] = {
+		[C(RESULT_MISS)]        = { 0x04, CNTR_EVEN },
+	},
+	[C(OP_WRITE)] = {
+		[C(RESULT_MISS)]        = { 0x04, CNTR_EVEN },
+	},
+},
+[C(DTLB)] = {
+	[C(OP_READ)] = {
+		[C(RESULT_MISS)]        = { 0x09, CNTR_ODD },
+	},
+	[C(OP_WRITE)] = {
+		[C(RESULT_MISS)]        = { 0x09, CNTR_ODD },
+	},
+},
+[C(ITLB)] = {
+	[C(OP_READ)] = {
+		[C(RESULT_MISS)]        = { 0x0c, CNTR_ODD },
+	},
+	[C(OP_WRITE)] = {
+		[C(RESULT_MISS)]        = { 0x0c, CNTR_ODD },
+	},
+},
+[C(BPU)] = {
+	/* Using the same code for *HW_BRANCH* */
+	[C(OP_READ)] = {
+		[C(RESULT_ACCESS)]      = { 0x01, CNTR_EVEN },
+		[C(RESULT_MISS)]        = { 0x01, CNTR_ODD },
+	},
+	[C(OP_WRITE)] = {
+		[C(RESULT_ACCESS)]      = { 0x01, CNTR_EVEN },
+		[C(RESULT_MISS)]        = { 0x01, CNTR_ODD },
+	},
+},
+};
+
+static const struct mips_perf_event loongson3_cache_map2
+				[PERF_COUNT_HW_CACHE_MAX]
+				[PERF_COUNT_HW_CACHE_OP_MAX]
+				[PERF_COUNT_HW_CACHE_RESULT_MAX] = {
+[C(L1D)] = {
+	/*
+	 * Like some other architectures (e.g. ARM), the performance
+	 * counters don't differentiate between read and write
+	 * accesses/misses, so this isn't strictly correct, but it's the
+	 * best we can do. Writes and reads get combined.
+	 */
+	[C(OP_READ)] = {
+		[C(RESULT_ACCESS)]	= { 0x156, CNTR_ALL },
+	},
+	[C(OP_WRITE)] = {
+		[C(RESULT_ACCESS)]	= { 0x155, CNTR_ALL },
+		[C(RESULT_MISS)]        = { 0x153, CNTR_ALL },
+	},
+},
+[C(L1I)] = {
+	[C(OP_READ)] = {
+		[C(RESULT_MISS)]	= { 0x18, CNTR_ALL },
+	},
+	[C(OP_WRITE)] = {
+		[C(RESULT_MISS)]        = { 0x18, CNTR_ALL },
+	},
+},
+[C(LL)] = {
+	[C(OP_READ)] = {
+		[C(RESULT_ACCESS)]	= { 0x1b6, CNTR_ALL },
+	},
+	[C(OP_WRITE)] = {
+		[C(RESULT_ACCESS)]	= { 0x1b7, CNTR_ALL },
+	},
+	[C(OP_PREFETCH)] = {
+		[C(RESULT_ACCESS)]	= { 0x1bf, CNTR_ALL },
+	},
+},
+[C(DTLB)] = {
+	[C(OP_READ)] = {
+		[C(RESULT_MISS)]        = { 0x92, CNTR_ALL },
+	},
+	[C(OP_WRITE)] = {
+		[C(RESULT_MISS)]        = { 0x92, CNTR_ALL },
+	},
+},
+[C(ITLB)] = {
+	[C(OP_READ)] = {
+		[C(RESULT_MISS)]	= { 0x1a, CNTR_ALL },
+	},
+	[C(OP_WRITE)] = {
+		[C(RESULT_MISS)]	= { 0x1a, CNTR_ALL },
+	},
+},
+[C(BPU)] = {
+	/* Using the same code for *HW_BRANCH* */
+	[C(OP_READ)] = {
+		[C(RESULT_ACCESS)]      = { 0x94, CNTR_ALL },
+		[C(RESULT_MISS)]        = { 0x9c, CNTR_ALL },
+	},
+},
+};
+
+static const struct mips_perf_event loongson3_cache_map3
+				[PERF_COUNT_HW_CACHE_MAX]
+				[PERF_COUNT_HW_CACHE_OP_MAX]
+				[PERF_COUNT_HW_CACHE_RESULT_MAX] = {
+[C(L1D)] = {
+	/*
+	 * Like some other architectures (e.g. ARM), the performance
+	 * counters don't differentiate between read and write
+	 * accesses/misses, so this isn't strictly correct, but it's the
+	 * best we can do. Writes and reads get combined.
+	 */
+	[C(OP_READ)] = {
+		[C(RESULT_ACCESS)]      = { 0x1e, CNTR_ALL },
+		[C(RESULT_MISS)]        = { 0x1f, CNTR_ALL },
+	},
+	[C(OP_PREFETCH)] = {
+		[C(RESULT_ACCESS)]	= { 0xaa, CNTR_ALL },
+		[C(RESULT_MISS)]	= { 0xa9, CNTR_ALL },
+	},
+},
+[C(L1I)] = {
+	[C(OP_READ)] = {
+		[C(RESULT_ACCESS)]	= { 0x1c, CNTR_ALL },
+		[C(RESULT_MISS)]	= { 0x1d, CNTR_ALL },
+	},
+},
+[C(LL)] = {
+	[C(OP_READ)] = {
+		[C(RESULT_ACCESS)]	= { 0x2e, CNTR_ALL },
+		[C(RESULT_MISS)]	= { 0x2f, CNTR_ALL },
+	},
+},
+[C(DTLB)] = {
+	[C(OP_READ)] = {
+		[C(RESULT_ACCESS)]      = { 0x14, CNTR_ALL },
+		[C(RESULT_MISS)]	= { 0x1b, CNTR_ALL },
+	},
+},
+[C(ITLB)] = {
+	[C(OP_READ)] = {
+		[C(RESULT_MISS)]	= { 0x1a, CNTR_ALL },
+	},
+},
+[C(BPU)] = {
+	/* Using the same code for *HW_BRANCH* */
+	[C(OP_READ)] = {
+		[C(RESULT_ACCESS)]      = { 0x02, CNTR_ALL },
+		[C(RESULT_MISS)]        = { 0x08, CNTR_ALL },
+	},
+},
+};
+
+/* BMIPS5000 */
+static const struct mips_perf_event bmips5000_cache_map
+				[PERF_COUNT_HW_CACHE_MAX]
+				[PERF_COUNT_HW_CACHE_OP_MAX]
+				[PERF_COUNT_HW_CACHE_RESULT_MAX] = {
+[C(L1D)] = {
+	/*
+	 * Like some other architectures (e.g. ARM), the performance
+	 * counters don't differentiate between read and write
+	 * accesses/misses, so this isn't strictly correct, but it's the
+	 * best we can do. Writes and reads get combined.
+	 */
+	[C(OP_READ)] = {
+		[C(RESULT_ACCESS)]	= { 12, CNTR_EVEN, T },
+		[C(RESULT_MISS)]	= { 12, CNTR_ODD, T },
+	},
+	[C(OP_WRITE)] = {
+		[C(RESULT_ACCESS)]	= { 12, CNTR_EVEN, T },
+		[C(RESULT_MISS)]	= { 12, CNTR_ODD, T },
+	},
+},
+[C(L1I)] = {
+	[C(OP_READ)] = {
+		[C(RESULT_ACCESS)]	= { 10, CNTR_EVEN, T },
+		[C(RESULT_MISS)]	= { 10, CNTR_ODD, T },
+	},
+	[C(OP_WRITE)] = {
+		[C(RESULT_ACCESS)]	= { 10, CNTR_EVEN, T },
+		[C(RESULT_MISS)]	= { 10, CNTR_ODD, T },
+	},
+	[C(OP_PREFETCH)] = {
+		[C(RESULT_ACCESS)]	= { 23, CNTR_EVEN, T },
+		/*
+		 * Note that MIPS has only "hit" events countable for
+		 * the prefetch operation.
+		 */
+	},
+},
+[C(LL)] = {
+	[C(OP_READ)] = {
+		[C(RESULT_ACCESS)]	= { 28, CNTR_EVEN, P },
+		[C(RESULT_MISS)]	= { 28, CNTR_ODD, P },
+	},
+	[C(OP_WRITE)] = {
+		[C(RESULT_ACCESS)]	= { 28, CNTR_EVEN, P },
+		[C(RESULT_MISS)]	= { 28, CNTR_ODD, P },
+	},
+},
+[C(BPU)] = {
+	/* Using the same code for *HW_BRANCH* */
+	[C(OP_READ)] = {
+		[C(RESULT_MISS)]	= { 0x02, CNTR_ODD, T },
+	},
+	[C(OP_WRITE)] = {
+		[C(RESULT_MISS)]	= { 0x02, CNTR_ODD, T },
+	},
+},
+};
+
+static const struct mips_perf_event octeon_cache_map
+				[PERF_COUNT_HW_CACHE_MAX]
+				[PERF_COUNT_HW_CACHE_OP_MAX]
+				[PERF_COUNT_HW_CACHE_RESULT_MAX] = {
+[C(L1D)] = {
+	[C(OP_READ)] = {
+		[C(RESULT_ACCESS)]	= { 0x2b, CNTR_ALL },
+		[C(RESULT_MISS)]	= { 0x2e, CNTR_ALL },
+	},
+	[C(OP_WRITE)] = {
+		[C(RESULT_ACCESS)]	= { 0x30, CNTR_ALL },
+	},
+},
+[C(L1I)] = {
+	[C(OP_READ)] = {
+		[C(RESULT_ACCESS)]	= { 0x18, CNTR_ALL },
+	},
+	[C(OP_PREFETCH)] = {
+		[C(RESULT_ACCESS)]	= { 0x19, CNTR_ALL },
+	},
+},
+[C(DTLB)] = {
+	/*
+	 * Only general DTLB misses are counted use the same event for
+	 * read and write.
+	 */
+	[C(OP_READ)] = {
+		[C(RESULT_MISS)]	= { 0x35, CNTR_ALL },
+	},
+	[C(OP_WRITE)] = {
+		[C(RESULT_MISS)]	= { 0x35, CNTR_ALL },
+	},
+},
+[C(ITLB)] = {
+	[C(OP_READ)] = {
+		[C(RESULT_MISS)]	= { 0x37, CNTR_ALL },
+	},
+},
+};
+
+static int __hw_perf_event_init(struct perf_event *event)
+{
+	struct perf_event_attr *attr = &event->attr;
+	struct hw_perf_event *hwc = &event->hw;
+	const struct mips_perf_event *pev;
+	int err;
+
+	/* Returning MIPS event descriptor for generic perf event. */
+	if (PERF_TYPE_HARDWARE == event->attr.type) {
+		if (event->attr.config >= PERF_COUNT_HW_MAX)
+			return -EINVAL;
+		pev = mipspmu_map_general_event(event->attr.config);
+	} else if (PERF_TYPE_HW_CACHE == event->attr.type) {
+		pev = mipspmu_map_cache_event(event->attr.config);
+	} else if (PERF_TYPE_RAW == event->attr.type) {
+		/* We are working on the global raw event. */
+		mutex_lock(&raw_event_mutex);
+		pev = mipspmu.map_raw_event(event->attr.config);
+	} else {
+		/* The event type is not (yet) supported. */
+		return -EOPNOTSUPP;
+	}
+
+	if (IS_ERR(pev)) {
+		if (PERF_TYPE_RAW == event->attr.type)
+			mutex_unlock(&raw_event_mutex);
+		return PTR_ERR(pev);
+	}
+
+	/*
+	 * We allow max flexibility on how each individual counter shared
+	 * by the single CPU operates (the mode exclusion and the range).
+	 */
+	hwc->config_base = MIPS_PERFCTRL_IE;
+
+	hwc->event_base = mipspmu_perf_event_encode(pev);
+	if (PERF_TYPE_RAW == event->attr.type)
+		mutex_unlock(&raw_event_mutex);
+
+	if (!attr->exclude_user)
+		hwc->config_base |= MIPS_PERFCTRL_U;
+	if (!attr->exclude_kernel) {
+		hwc->config_base |= MIPS_PERFCTRL_K;
+		/* MIPS kernel mode: KSU == 00b || EXL == 1 || ERL == 1 */
+		hwc->config_base |= MIPS_PERFCTRL_EXL;
+	}
+	if (!attr->exclude_hv)
+		hwc->config_base |= MIPS_PERFCTRL_S;
+
+	hwc->config_base &= M_PERFCTL_CONFIG_MASK;
+	/*
+	 * The event can belong to another cpu. We do not assign a local
+	 * counter for it for now.
+	 */
+	hwc->idx = -1;
+	hwc->config = 0;
+
+	if (!hwc->sample_period) {
+		hwc->sample_period  = mipspmu.max_period;
+		hwc->last_period    = hwc->sample_period;
+		local64_set(&hwc->period_left, hwc->sample_period);
+	}
+
+	err = 0;
+	if (event->group_leader != event)
+		err = validate_group(event);
+
+	event->destroy = hw_perf_event_destroy;
+
+	if (err)
+		event->destroy(event);
+
+	return err;
+}
+
+static void pause_local_counters(void)
+{
+	struct cpu_hw_events *cpuc = this_cpu_ptr(&cpu_hw_events);
+	int ctr = mipspmu.num_counters;
+	unsigned long flags;
+
+	local_irq_save(flags);
+	do {
+		ctr--;
+		cpuc->saved_ctrl[ctr] = mipsxx_pmu_read_control(ctr);
+		mipsxx_pmu_write_control(ctr, cpuc->saved_ctrl[ctr] &
+					 ~M_PERFCTL_COUNT_EVENT_WHENEVER);
+	} while (ctr > 0);
+	local_irq_restore(flags);
+}
+
+static void resume_local_counters(void)
+{
+	struct cpu_hw_events *cpuc = this_cpu_ptr(&cpu_hw_events);
+	int ctr = mipspmu.num_counters;
+
+	do {
+		ctr--;
+		mipsxx_pmu_write_control(ctr, cpuc->saved_ctrl[ctr]);
+	} while (ctr > 0);
+}
+
+static int mipsxx_pmu_handle_shared_irq(void)
+{
+	struct cpu_hw_events *cpuc = this_cpu_ptr(&cpu_hw_events);
+	struct perf_sample_data data;
+	unsigned int counters = mipspmu.num_counters;
+	u64 counter;
+	int n, handled = IRQ_NONE;
+	struct pt_regs *regs;
+
+	if (cpu_has_perf_cntr_intr_bit && !(read_c0_cause() & CAUSEF_PCI))
+		return handled;
+	/*
+	 * First we pause the local counters, so that when we are locked
+	 * here, the counters are all paused. When it gets locked due to
+	 * perf_disable(), the timer interrupt handler will be delayed.
+	 *
+	 * See also mipsxx_pmu_start().
+	 */
+	pause_local_counters();
+#ifdef CONFIG_MIPS_PERF_SHARED_TC_COUNTERS
+	read_lock(&pmuint_rwlock);
+#endif
+
+	regs = get_irq_regs();
+
+	perf_sample_data_init(&data, 0, 0);
+
+	for (n = counters - 1; n >= 0; n--) {
+		if (!test_bit(n, cpuc->used_mask))
+			continue;
+
+		counter = mipspmu.read_counter(n);
+		if (!(counter & mipspmu.overflow))
+			continue;
+
+		handle_associated_event(cpuc, n, &data, regs);
+		handled = IRQ_HANDLED;
+	}
+
+#ifdef CONFIG_MIPS_PERF_SHARED_TC_COUNTERS
+	read_unlock(&pmuint_rwlock);
+#endif
+	resume_local_counters();
+
+	/*
+	 * Do all the work for the pending perf events. We can do this
+	 * in here because the performance counter interrupt is a regular
+	 * interrupt, not NMI.
+	 */
+	if (handled == IRQ_HANDLED)
+		irq_work_run();
+
+	return handled;
+}
+
+static irqreturn_t mipsxx_pmu_handle_irq(int irq, void *dev)
+{
+	return mipsxx_pmu_handle_shared_irq();
+}
+
+/* 24K */
+#define IS_BOTH_COUNTERS_24K_EVENT(b)					\
+	((b) == 0 || (b) == 1 || (b) == 11)
+
+/* 34K */
+#define IS_BOTH_COUNTERS_34K_EVENT(b)					\
+	((b) == 0 || (b) == 1 || (b) == 11)
+#ifdef CONFIG_MIPS_MT_SMP
+#define IS_RANGE_P_34K_EVENT(r, b)					\
+	((b) == 0 || (r) == 18 || (b) == 21 || (b) == 22 ||		\
+	 (b) == 25 || (b) == 39 || (r) == 44 || (r) == 174 ||		\
+	 (r) == 176 || ((b) >= 50 && (b) <= 55) ||			\
+	 ((b) >= 64 && (b) <= 67))
+#define IS_RANGE_V_34K_EVENT(r) ((r) == 47)
+#endif
+
+/* 74K */
+#define IS_BOTH_COUNTERS_74K_EVENT(b)					\
+	((b) == 0 || (b) == 1)
+
+/* proAptiv */
+#define IS_BOTH_COUNTERS_PROAPTIV_EVENT(b)				\
+	((b) == 0 || (b) == 1)
+/* P5600 */
+#define IS_BOTH_COUNTERS_P5600_EVENT(b)					\
+	((b) == 0 || (b) == 1)
+
+/* 1004K */
+#define IS_BOTH_COUNTERS_1004K_EVENT(b)					\
+	((b) == 0 || (b) == 1 || (b) == 11)
+#ifdef CONFIG_MIPS_MT_SMP
+#define IS_RANGE_P_1004K_EVENT(r, b)					\
+	((b) == 0 || (r) == 18 || (b) == 21 || (b) == 22 ||		\
+	 (b) == 25 || (b) == 36 || (b) == 39 || (r) == 44 ||		\
+	 (r) == 174 || (r) == 176 || ((b) >= 50 && (b) <= 59) ||	\
+	 (r) == 188 || (b) == 61 || (b) == 62 ||			\
+	 ((b) >= 64 && (b) <= 67))
+#define IS_RANGE_V_1004K_EVENT(r)	((r) == 47)
+#endif
+
+/* interAptiv */
+#define IS_BOTH_COUNTERS_INTERAPTIV_EVENT(b)				\
+	((b) == 0 || (b) == 1 || (b) == 11)
+#ifdef CONFIG_MIPS_MT_SMP
+/* The P/V/T info is not provided for "(b) == 38" in SUM, assume P. */
+#define IS_RANGE_P_INTERAPTIV_EVENT(r, b)				\
+	((b) == 0 || (r) == 18 || (b) == 21 || (b) == 22 ||		\
+	 (b) == 25 || (b) == 36 || (b) == 38 || (b) == 39 ||		\
+	 (r) == 44 || (r) == 174 || (r) == 176 || ((b) >= 50 &&		\
+	 (b) <= 59) || (r) == 188 || (b) == 61 || (b) == 62 ||		\
+	 ((b) >= 64 && (b) <= 67))
+#define IS_RANGE_V_INTERAPTIV_EVENT(r)	((r) == 47 || (r) == 175)
+#endif
+
+/* BMIPS5000 */
+#define IS_BOTH_COUNTERS_BMIPS5000_EVENT(b)				\
+	((b) == 0 || (b) == 1)
+
+
+/*
+ * For most cores the user can use 0-255 raw events, where 0-127 for the events
+ * of even counters, and 128-255 for odd counters. Note that bit 7 is used to
+ * indicate the even/odd bank selector. So, for example, when user wants to take
+ * the Event Num of 15 for odd counters (by referring to the user manual), then
+ * 128 needs to be added to 15 as the input for the event config, i.e., 143 (0x8F)
+ * to be used.
+ *
+ * Some newer cores have even more events, in which case the user can use raw
+ * events 0-511, where 0-255 are for the events of even counters, and 256-511
+ * are for odd counters, so bit 8 is used to indicate the even/odd bank selector.
+ */
+static const struct mips_perf_event *mipsxx_pmu_map_raw_event(u64 config)
+{
+	/* currently most cores have 7-bit event numbers */
+	int pmu_type;
+	unsigned int raw_id = config & 0xff;
+	unsigned int base_id = raw_id & 0x7f;
+
+	switch (current_cpu_type()) {
+	case CPU_24K:
+		if (IS_BOTH_COUNTERS_24K_EVENT(base_id))
+			raw_event.cntr_mask = CNTR_EVEN | CNTR_ODD;
+		else
+			raw_event.cntr_mask =
+				raw_id > 127 ? CNTR_ODD : CNTR_EVEN;
+#ifdef CONFIG_MIPS_MT_SMP
+		/*
+		 * This is actually doing nothing. Non-multithreading
+		 * CPUs will not check and calculate the range.
+		 */
+		raw_event.range = P;
+#endif
+		break;
+	case CPU_34K:
+		if (IS_BOTH_COUNTERS_34K_EVENT(base_id))
+			raw_event.cntr_mask = CNTR_EVEN | CNTR_ODD;
+		else
+			raw_event.cntr_mask =
+				raw_id > 127 ? CNTR_ODD : CNTR_EVEN;
+#ifdef CONFIG_MIPS_MT_SMP
+		if (IS_RANGE_P_34K_EVENT(raw_id, base_id))
+			raw_event.range = P;
+		else if (unlikely(IS_RANGE_V_34K_EVENT(raw_id)))
+			raw_event.range = V;
+		else
+			raw_event.range = T;
+#endif
+		break;
+	case CPU_74K:
+	case CPU_1074K:
+		if (IS_BOTH_COUNTERS_74K_EVENT(base_id))
+			raw_event.cntr_mask = CNTR_EVEN | CNTR_ODD;
+		else
+			raw_event.cntr_mask =
+				raw_id > 127 ? CNTR_ODD : CNTR_EVEN;
+#ifdef CONFIG_MIPS_MT_SMP
+		raw_event.range = P;
+#endif
+		break;
+	case CPU_PROAPTIV:
+		if (IS_BOTH_COUNTERS_PROAPTIV_EVENT(base_id))
+			raw_event.cntr_mask = CNTR_EVEN | CNTR_ODD;
+		else
+			raw_event.cntr_mask =
+				raw_id > 127 ? CNTR_ODD : CNTR_EVEN;
+#ifdef CONFIG_MIPS_MT_SMP
+		raw_event.range = P;
+#endif
+		break;
+	case CPU_P5600:
+	case CPU_P6600:
+		/* 8-bit event numbers */
+		raw_id = config & 0x1ff;
+		base_id = raw_id & 0xff;
+		if (IS_BOTH_COUNTERS_P5600_EVENT(base_id))
+			raw_event.cntr_mask = CNTR_EVEN | CNTR_ODD;
+		else
+			raw_event.cntr_mask =
+				raw_id > 255 ? CNTR_ODD : CNTR_EVEN;
+#ifdef CONFIG_MIPS_MT_SMP
+		raw_event.range = P;
+#endif
+		break;
+	case CPU_I6400:
+	case CPU_I6500:
+		/* 8-bit event numbers */
+		base_id = config & 0xff;
+		raw_event.cntr_mask = CNTR_EVEN | CNTR_ODD;
+		break;
+	case CPU_1004K:
+		if (IS_BOTH_COUNTERS_1004K_EVENT(base_id))
+			raw_event.cntr_mask = CNTR_EVEN | CNTR_ODD;
+		else
+			raw_event.cntr_mask =
+				raw_id > 127 ? CNTR_ODD : CNTR_EVEN;
+#ifdef CONFIG_MIPS_MT_SMP
+		if (IS_RANGE_P_1004K_EVENT(raw_id, base_id))
+			raw_event.range = P;
+		else if (unlikely(IS_RANGE_V_1004K_EVENT(raw_id)))
+			raw_event.range = V;
+		else
+			raw_event.range = T;
+#endif
+		break;
+	case CPU_INTERAPTIV:
+		if (IS_BOTH_COUNTERS_INTERAPTIV_EVENT(base_id))
+			raw_event.cntr_mask = CNTR_EVEN | CNTR_ODD;
+		else
+			raw_event.cntr_mask =
+				raw_id > 127 ? CNTR_ODD : CNTR_EVEN;
+#ifdef CONFIG_MIPS_MT_SMP
+		if (IS_RANGE_P_INTERAPTIV_EVENT(raw_id, base_id))
+			raw_event.range = P;
+		else if (unlikely(IS_RANGE_V_INTERAPTIV_EVENT(raw_id)))
+			raw_event.range = V;
+		else
+			raw_event.range = T;
+#endif
+		break;
+	case CPU_BMIPS5000:
+		if (IS_BOTH_COUNTERS_BMIPS5000_EVENT(base_id))
+			raw_event.cntr_mask = CNTR_EVEN | CNTR_ODD;
+		else
+			raw_event.cntr_mask =
+				raw_id > 127 ? CNTR_ODD : CNTR_EVEN;
+		break;
+	case CPU_LOONGSON64:
+		pmu_type = get_loongson3_pmu_type();
+
+		switch (pmu_type) {
+		case LOONGSON_PMU_TYPE1:
+			raw_event.cntr_mask =
+				raw_id > 127 ? CNTR_ODD : CNTR_EVEN;
+			break;
+		case LOONGSON_PMU_TYPE2:
+			base_id = config & 0x3ff;
+			raw_event.cntr_mask = CNTR_ALL;
+
+			if ((base_id >= 1 && base_id < 28) ||
+				(base_id >= 64 && base_id < 90) ||
+				(base_id >= 128 && base_id < 164) ||
+				(base_id >= 192 && base_id < 200) ||
+				(base_id >= 256 && base_id < 275) ||
+				(base_id >= 320 && base_id < 361) ||
+				(base_id >= 384 && base_id < 574))
+				break;
+
+			return ERR_PTR(-EOPNOTSUPP);
+		case LOONGSON_PMU_TYPE3:
+			base_id = raw_id;
+			raw_event.cntr_mask = CNTR_ALL;
+			break;
+		}
+		break;
+	}
+
+	raw_event.event_id = base_id;
+
+	return &raw_event;
+}
+
+static const struct mips_perf_event *octeon_pmu_map_raw_event(u64 config)
+{
+	unsigned int base_id = config & 0x7f;
+	unsigned int event_max;
+
+
+	raw_event.cntr_mask = CNTR_ALL;
+	raw_event.event_id = base_id;
+
+	if (current_cpu_type() == CPU_CAVIUM_OCTEON3)
+		event_max = 0x5f;
+	else if (current_cpu_type() == CPU_CAVIUM_OCTEON2)
+		event_max = 0x42;
+	else
+		event_max = 0x3a;
+
+	if (base_id > event_max) {
+		return ERR_PTR(-EOPNOTSUPP);
+	}
+
+	switch (base_id) {
+	case 0x00:
+	case 0x0f:
+	case 0x1e:
+	case 0x1f:
+	case 0x2f:
+	case 0x34:
+	case 0x3e ... 0x3f:
+		return ERR_PTR(-EOPNOTSUPP);
+	default:
+		break;
+	}
+
+	return &raw_event;
+}
+
+static int __init
+init_hw_perf_events(void)
+{
+	int counters, irq, pmu_type;
+
+	pr_info("Performance counters: ");
+
+	counters = n_counters();
+	if (counters == 0) {
+		pr_cont("No available PMU.\n");
+		return -ENODEV;
+	}
+
+#ifdef CONFIG_MIPS_PERF_SHARED_TC_COUNTERS
+	if (!cpu_has_mipsmt_pertccounters)
+		counters = counters_total_to_per_cpu(counters);
+#endif
+
+	if (get_c0_perfcount_int)
+		irq = get_c0_perfcount_int();
+	else if (cp0_perfcount_irq >= 0)
+		irq = MIPS_CPU_IRQ_BASE + cp0_perfcount_irq;
+	else
+		irq = -1;
+
+	mipspmu.map_raw_event = mipsxx_pmu_map_raw_event;
+
+	switch (current_cpu_type()) {
+	case CPU_24K:
+		mipspmu.name = "mips/24K";
+		mipspmu.general_event_map = &mipsxxcore_event_map;
+		mipspmu.cache_event_map = &mipsxxcore_cache_map;
+		break;
+	case CPU_34K:
+		mipspmu.name = "mips/34K";
+		mipspmu.general_event_map = &mipsxxcore_event_map;
+		mipspmu.cache_event_map = &mipsxxcore_cache_map;
+		break;
+	case CPU_74K:
+		mipspmu.name = "mips/74K";
+		mipspmu.general_event_map = &mipsxxcore_event_map2;
+		mipspmu.cache_event_map = &mipsxxcore_cache_map2;
+		break;
+	case CPU_PROAPTIV:
+		mipspmu.name = "mips/proAptiv";
+		mipspmu.general_event_map = &mipsxxcore_event_map2;
+		mipspmu.cache_event_map = &mipsxxcore_cache_map2;
+		break;
+	case CPU_P5600:
+		mipspmu.name = "mips/P5600";
+		mipspmu.general_event_map = &mipsxxcore_event_map2;
+		mipspmu.cache_event_map = &mipsxxcore_cache_map2;
+		break;
+	case CPU_P6600:
+		mipspmu.name = "mips/P6600";
+		mipspmu.general_event_map = &mipsxxcore_event_map2;
+		mipspmu.cache_event_map = &mipsxxcore_cache_map2;
+		break;
+	case CPU_I6400:
+		mipspmu.name = "mips/I6400";
+		mipspmu.general_event_map = &i6x00_event_map;
+		mipspmu.cache_event_map = &i6x00_cache_map;
+		break;
+	case CPU_I6500:
+		mipspmu.name = "mips/I6500";
+		mipspmu.general_event_map = &i6x00_event_map;
+		mipspmu.cache_event_map = &i6x00_cache_map;
+		break;
+	case CPU_1004K:
+		mipspmu.name = "mips/1004K";
+		mipspmu.general_event_map = &mipsxxcore_event_map;
+		mipspmu.cache_event_map = &mipsxxcore_cache_map;
+		break;
+	case CPU_1074K:
+		mipspmu.name = "mips/1074K";
+		mipspmu.general_event_map = &mipsxxcore_event_map;
+		mipspmu.cache_event_map = &mipsxxcore_cache_map;
+		break;
+	case CPU_INTERAPTIV:
+		mipspmu.name = "mips/interAptiv";
+		mipspmu.general_event_map = &mipsxxcore_event_map;
+		mipspmu.cache_event_map = &mipsxxcore_cache_map;
+		break;
+	case CPU_LOONGSON32:
+		mipspmu.name = "mips/loongson1";
+		mipspmu.general_event_map = &mipsxxcore_event_map;
+		mipspmu.cache_event_map = &mipsxxcore_cache_map;
+		break;
+	case CPU_LOONGSON64:
+		mipspmu.name = "mips/loongson3";
+		pmu_type = get_loongson3_pmu_type();
+
+		switch (pmu_type) {
+		case LOONGSON_PMU_TYPE1:
+			counters = 2;
+			mipspmu.general_event_map = &loongson3_event_map1;
+			mipspmu.cache_event_map = &loongson3_cache_map1;
+			break;
+		case LOONGSON_PMU_TYPE2:
+			counters = 4;
+			mipspmu.general_event_map = &loongson3_event_map2;
+			mipspmu.cache_event_map = &loongson3_cache_map2;
+			break;
+		case LOONGSON_PMU_TYPE3:
+			counters = 4;
+			mipspmu.general_event_map = &loongson3_event_map3;
+			mipspmu.cache_event_map = &loongson3_cache_map3;
+			break;
+		}
+		break;
+	case CPU_CAVIUM_OCTEON:
+	case CPU_CAVIUM_OCTEON_PLUS:
+	case CPU_CAVIUM_OCTEON2:
+	case CPU_CAVIUM_OCTEON3:
+		mipspmu.name = "octeon";
+		mipspmu.general_event_map = &octeon_event_map;
+		mipspmu.cache_event_map = &octeon_cache_map;
+		mipspmu.map_raw_event = octeon_pmu_map_raw_event;
+		break;
+	case CPU_BMIPS5000:
+		mipspmu.name = "BMIPS5000";
+		mipspmu.general_event_map = &bmips5000_event_map;
+		mipspmu.cache_event_map = &bmips5000_cache_map;
+		break;
+	default:
+		pr_cont("Either hardware does not support performance "
+			"counters, or not yet implemented.\n");
+		return -ENODEV;
+	}
+
+	mipspmu.num_counters = counters;
+	mipspmu.irq = irq;
+
+	if (read_c0_perfctrl0() & MIPS_PERFCTRL_W) {
+		if (get_loongson3_pmu_type() == LOONGSON_PMU_TYPE2) {
+			counter_bits = 48;
+			mipspmu.max_period = (1ULL << 47) - 1;
+			mipspmu.valid_count = (1ULL << 47) - 1;
+			mipspmu.overflow = 1ULL << 47;
+		} else {
+			counter_bits = 64;
+			mipspmu.max_period = (1ULL << 63) - 1;
+			mipspmu.valid_count = (1ULL << 63) - 1;
+			mipspmu.overflow = 1ULL << 63;
+		}
+		mipspmu.read_counter = mipsxx_pmu_read_counter_64;
+		mipspmu.write_counter = mipsxx_pmu_write_counter_64;
+	} else {
+		counter_bits = 32;
+		mipspmu.max_period = (1ULL << 31) - 1;
+		mipspmu.valid_count = (1ULL << 31) - 1;
+		mipspmu.overflow = 1ULL << 31;
+		mipspmu.read_counter = mipsxx_pmu_read_counter;
+		mipspmu.write_counter = mipsxx_pmu_write_counter;
+	}
+
+	on_each_cpu(reset_counters, (void *)(long)counters, 1);
+
+	pr_cont("%s PMU enabled, %d %d-bit counters available to each "
+		"CPU, irq %d%s\n", mipspmu.name, counters, counter_bits, irq,
+		irq < 0 ? " (share with timer interrupt)" : "");
+
+	perf_pmu_register(&pmu, "cpu", PERF_TYPE_RAW);
+
+	return 0;
+}
+early_initcall(init_hw_perf_events);
diff --git a/arch/mips/kernel/perf_regs.c b/arch/mips/kernel/perf_regs.c
new file mode 100644
index 000000000..e686780d1
--- /dev/null
+++ b/arch/mips/kernel/perf_regs.c
@@ -0,0 +1,68 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Some parts derived from x86 version of this file.
+ *
+ * Copyright (C) 2013 Cavium, Inc.
+ */
+
+#include <linux/perf_event.h>
+
+#include <asm/ptrace.h>
+
+#ifdef CONFIG_32BIT
+u64 perf_reg_abi(struct task_struct *tsk)
+{
+	return PERF_SAMPLE_REGS_ABI_32;
+}
+#else /* Must be CONFIG_64BIT */
+u64 perf_reg_abi(struct task_struct *tsk)
+{
+	if (test_tsk_thread_flag(tsk, TIF_32BIT_REGS))
+		return PERF_SAMPLE_REGS_ABI_32;
+	else
+		return PERF_SAMPLE_REGS_ABI_64;
+}
+#endif /* CONFIG_32BIT */
+
+int perf_reg_validate(u64 mask)
+{
+	if (!mask)
+		return -EINVAL;
+	if (mask & ~((1ull << PERF_REG_MIPS_MAX) - 1))
+		return -EINVAL;
+	return 0;
+}
+
+u64 perf_reg_value(struct pt_regs *regs, int idx)
+{
+	long v;
+
+	switch (idx) {
+	case PERF_REG_MIPS_PC:
+		v = regs->cp0_epc;
+		break;
+	case PERF_REG_MIPS_R1 ... PERF_REG_MIPS_R25:
+		v = regs->regs[idx - PERF_REG_MIPS_R1 + 1];
+		break;
+	case PERF_REG_MIPS_R28 ... PERF_REG_MIPS_R31:
+		v = regs->regs[idx - PERF_REG_MIPS_R28 + 28];
+		break;
+
+	default:
+		WARN_ON_ONCE(1);
+		return 0;
+	}
+
+	return (s64)v; /* Sign extend if 32-bit. */
+}
+
+void perf_get_regs_user(struct perf_regs *regs_user,
+			struct pt_regs *regs)
+{
+	regs_user->regs = task_pt_regs(current);
+	regs_user->abi = perf_reg_abi(current);
+}
diff --git a/arch/mips/kernel/pm-cps.c b/arch/mips/kernel/pm-cps.c
new file mode 100644
index 000000000..9bf60d7d4
--- /dev/null
+++ b/arch/mips/kernel/pm-cps.c
@@ -0,0 +1,738 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2014 Imagination Technologies
+ * Author: Paul Burton <paul.burton@mips.com>
+ */
+
+#include <linux/cpuhotplug.h>
+#include <linux/init.h>
+#include <linux/percpu.h>
+#include <linux/slab.h>
+#include <linux/suspend.h>
+
+#include <asm/asm-offsets.h>
+#include <asm/cacheflush.h>
+#include <asm/cacheops.h>
+#include <asm/idle.h>
+#include <asm/mips-cps.h>
+#include <asm/mipsmtregs.h>
+#include <asm/pm.h>
+#include <asm/pm-cps.h>
+#include <asm/smp-cps.h>
+#include <asm/uasm.h>
+
+/*
+ * cps_nc_entry_fn - type of a generated non-coherent state entry function
+ * @online: the count of online coupled VPEs
+ * @nc_ready_count: pointer to a non-coherent mapping of the core ready_count
+ *
+ * The code entering & exiting non-coherent states is generated at runtime
+ * using uasm, in order to ensure that the compiler cannot insert a stray
+ * memory access at an unfortunate time and to allow the generation of optimal
+ * core-specific code particularly for cache routines. If coupled_coherence
+ * is non-zero and this is the entry function for the CPS_PM_NC_WAIT state,
+ * returns the number of VPEs that were in the wait state at the point this
+ * VPE left it. Returns garbage if coupled_coherence is zero or this is not
+ * the entry function for CPS_PM_NC_WAIT.
+ */
+typedef unsigned (*cps_nc_entry_fn)(unsigned online, u32 *nc_ready_count);
+
+/*
+ * The entry point of the generated non-coherent idle state entry/exit
+ * functions. Actually per-core rather than per-CPU.
+ */
+static DEFINE_PER_CPU_READ_MOSTLY(cps_nc_entry_fn[CPS_PM_STATE_COUNT],
+				  nc_asm_enter);
+
+/* Bitmap indicating which states are supported by the system */
+static DECLARE_BITMAP(state_support, CPS_PM_STATE_COUNT);
+
+/*
+ * Indicates the number of coupled VPEs ready to operate in a non-coherent
+ * state. Actually per-core rather than per-CPU.
+ */
+static DEFINE_PER_CPU_ALIGNED(u32*, ready_count);
+
+/* Indicates online CPUs coupled with the current CPU */
+static DEFINE_PER_CPU_ALIGNED(cpumask_t, online_coupled);
+
+/*
+ * Used to synchronize entry to deep idle states. Actually per-core rather
+ * than per-CPU.
+ */
+static DEFINE_PER_CPU_ALIGNED(atomic_t, pm_barrier);
+
+/* Saved CPU state across the CPS_PM_POWER_GATED state */
+DEFINE_PER_CPU_ALIGNED(struct mips_static_suspend_state, cps_cpu_state);
+
+/* A somewhat arbitrary number of labels & relocs for uasm */
+static struct uasm_label labels[32];
+static struct uasm_reloc relocs[32];
+
+enum mips_reg {
+	zero, at, v0, v1, a0, a1, a2, a3,
+	t0, t1, t2, t3, t4, t5, t6, t7,
+	s0, s1, s2, s3, s4, s5, s6, s7,
+	t8, t9, k0, k1, gp, sp, fp, ra,
+};
+
+bool cps_pm_support_state(enum cps_pm_state state)
+{
+	return test_bit(state, state_support);
+}
+
+static void coupled_barrier(atomic_t *a, unsigned online)
+{
+	/*
+	 * This function is effectively the same as
+	 * cpuidle_coupled_parallel_barrier, which can't be used here since
+	 * there's no cpuidle device.
+	 */
+
+	if (!coupled_coherence)
+		return;
+
+	smp_mb__before_atomic();
+	atomic_inc(a);
+
+	while (atomic_read(a) < online)
+		cpu_relax();
+
+	if (atomic_inc_return(a) == online * 2) {
+		atomic_set(a, 0);
+		return;
+	}
+
+	while (atomic_read(a) > online)
+		cpu_relax();
+}
+
+int cps_pm_enter_state(enum cps_pm_state state)
+{
+	unsigned cpu = smp_processor_id();
+	unsigned core = cpu_core(&current_cpu_data);
+	unsigned online, left;
+	cpumask_t *coupled_mask = this_cpu_ptr(&online_coupled);
+	u32 *core_ready_count, *nc_core_ready_count;
+	void *nc_addr;
+	cps_nc_entry_fn entry;
+	struct core_boot_config *core_cfg;
+	struct vpe_boot_config *vpe_cfg;
+
+	/* Check that there is an entry function for this state */
+	entry = per_cpu(nc_asm_enter, core)[state];
+	if (!entry)
+		return -EINVAL;
+
+	/* Calculate which coupled CPUs (VPEs) are online */
+#if defined(CONFIG_MIPS_MT) || defined(CONFIG_CPU_MIPSR6)
+	if (cpu_online(cpu)) {
+		cpumask_and(coupled_mask, cpu_online_mask,
+			    &cpu_sibling_map[cpu]);
+		online = cpumask_weight(coupled_mask);
+		cpumask_clear_cpu(cpu, coupled_mask);
+	} else
+#endif
+	{
+		cpumask_clear(coupled_mask);
+		online = 1;
+	}
+
+	/* Setup the VPE to run mips_cps_pm_restore when started again */
+	if (IS_ENABLED(CONFIG_CPU_PM) && state == CPS_PM_POWER_GATED) {
+		/* Power gating relies upon CPS SMP */
+		if (!mips_cps_smp_in_use())
+			return -EINVAL;
+
+		core_cfg = &mips_cps_core_bootcfg[core];
+		vpe_cfg = &core_cfg->vpe_config[cpu_vpe_id(&current_cpu_data)];
+		vpe_cfg->pc = (unsigned long)mips_cps_pm_restore;
+		vpe_cfg->gp = (unsigned long)current_thread_info();
+		vpe_cfg->sp = 0;
+	}
+
+	/* Indicate that this CPU might not be coherent */
+	cpumask_clear_cpu(cpu, &cpu_coherent_mask);
+	smp_mb__after_atomic();
+
+	/* Create a non-coherent mapping of the core ready_count */
+	core_ready_count = per_cpu(ready_count, core);
+	nc_addr = kmap_noncoherent(virt_to_page(core_ready_count),
+				   (unsigned long)core_ready_count);
+	nc_addr += ((unsigned long)core_ready_count & ~PAGE_MASK);
+	nc_core_ready_count = nc_addr;
+
+	/* Ensure ready_count is zero-initialised before the assembly runs */
+	WRITE_ONCE(*nc_core_ready_count, 0);
+	coupled_barrier(&per_cpu(pm_barrier, core), online);
+
+	/* Run the generated entry code */
+	left = entry(online, nc_core_ready_count);
+
+	/* Remove the non-coherent mapping of ready_count */
+	kunmap_noncoherent();
+
+	/* Indicate that this CPU is definitely coherent */
+	cpumask_set_cpu(cpu, &cpu_coherent_mask);
+
+	/*
+	 * If this VPE is the first to leave the non-coherent wait state then
+	 * it needs to wake up any coupled VPEs still running their wait
+	 * instruction so that they return to cpuidle, which can then complete
+	 * coordination between the coupled VPEs & provide the governor with
+	 * a chance to reflect on the length of time the VPEs were in the
+	 * idle state.
+	 */
+	if (coupled_coherence && (state == CPS_PM_NC_WAIT) && (left == online))
+		arch_send_call_function_ipi_mask(coupled_mask);
+
+	return 0;
+}
+
+static void cps_gen_cache_routine(u32 **pp, struct uasm_label **pl,
+				  struct uasm_reloc **pr,
+				  const struct cache_desc *cache,
+				  unsigned op, int lbl)
+{
+	unsigned cache_size = cache->ways << cache->waybit;
+	unsigned i;
+	const unsigned unroll_lines = 32;
+
+	/* If the cache isn't present this function has it easy */
+	if (cache->flags & MIPS_CACHE_NOT_PRESENT)
+		return;
+
+	/* Load base address */
+	UASM_i_LA(pp, t0, (long)CKSEG0);
+
+	/* Calculate end address */
+	if (cache_size < 0x8000)
+		uasm_i_addiu(pp, t1, t0, cache_size);
+	else
+		UASM_i_LA(pp, t1, (long)(CKSEG0 + cache_size));
+
+	/* Start of cache op loop */
+	uasm_build_label(pl, *pp, lbl);
+
+	/* Generate the cache ops */
+	for (i = 0; i < unroll_lines; i++) {
+		if (cpu_has_mips_r6) {
+			uasm_i_cache(pp, op, 0, t0);
+			uasm_i_addiu(pp, t0, t0, cache->linesz);
+		} else {
+			uasm_i_cache(pp, op, i * cache->linesz, t0);
+		}
+	}
+
+	if (!cpu_has_mips_r6)
+		/* Update the base address */
+		uasm_i_addiu(pp, t0, t0, unroll_lines * cache->linesz);
+
+	/* Loop if we haven't reached the end address yet */
+	uasm_il_bne(pp, pr, t0, t1, lbl);
+	uasm_i_nop(pp);
+}
+
+static int cps_gen_flush_fsb(u32 **pp, struct uasm_label **pl,
+			     struct uasm_reloc **pr,
+			     const struct cpuinfo_mips *cpu_info,
+			     int lbl)
+{
+	unsigned i, fsb_size = 8;
+	unsigned num_loads = (fsb_size * 3) / 2;
+	unsigned line_stride = 2;
+	unsigned line_size = cpu_info->dcache.linesz;
+	unsigned perf_counter, perf_event;
+	unsigned revision = cpu_info->processor_id & PRID_REV_MASK;
+
+	/*
+	 * Determine whether this CPU requires an FSB flush, and if so which
+	 * performance counter/event reflect stalls due to a full FSB.
+	 */
+	switch (__get_cpu_type(cpu_info->cputype)) {
+	case CPU_INTERAPTIV:
+		perf_counter = 1;
+		perf_event = 51;
+		break;
+
+	case CPU_PROAPTIV:
+		/* Newer proAptiv cores don't require this workaround */
+		if (revision >= PRID_REV_ENCODE_332(1, 1, 0))
+			return 0;
+
+		/* On older ones it's unavailable */
+		return -1;
+
+	default:
+		/* Assume that the CPU does not need this workaround */
+		return 0;
+	}
+
+	/*
+	 * Ensure that the fill/store buffer (FSB) is not holding the results
+	 * of a prefetch, since if it is then the CPC sequencer may become
+	 * stuck in the D3 (ClrBus) state whilst entering a low power state.
+	 */
+
+	/* Preserve perf counter setup */
+	uasm_i_mfc0(pp, t2, 25, (perf_counter * 2) + 0); /* PerfCtlN */
+	uasm_i_mfc0(pp, t3, 25, (perf_counter * 2) + 1); /* PerfCntN */
+
+	/* Setup perf counter to count FSB full pipeline stalls */
+	uasm_i_addiu(pp, t0, zero, (perf_event << 5) | 0xf);
+	uasm_i_mtc0(pp, t0, 25, (perf_counter * 2) + 0); /* PerfCtlN */
+	uasm_i_ehb(pp);
+	uasm_i_mtc0(pp, zero, 25, (perf_counter * 2) + 1); /* PerfCntN */
+	uasm_i_ehb(pp);
+
+	/* Base address for loads */
+	UASM_i_LA(pp, t0, (long)CKSEG0);
+
+	/* Start of clear loop */
+	uasm_build_label(pl, *pp, lbl);
+
+	/* Perform some loads to fill the FSB */
+	for (i = 0; i < num_loads; i++)
+		uasm_i_lw(pp, zero, i * line_size * line_stride, t0);
+
+	/*
+	 * Invalidate the new D-cache entries so that the cache will need
+	 * refilling (via the FSB) if the loop is executed again.
+	 */
+	for (i = 0; i < num_loads; i++) {
+		uasm_i_cache(pp, Hit_Invalidate_D,
+			     i * line_size * line_stride, t0);
+		uasm_i_cache(pp, Hit_Writeback_Inv_SD,
+			     i * line_size * line_stride, t0);
+	}
+
+	/* Barrier ensuring previous cache invalidates are complete */
+	uasm_i_sync(pp, __SYNC_full);
+	uasm_i_ehb(pp);
+
+	/* Check whether the pipeline stalled due to the FSB being full */
+	uasm_i_mfc0(pp, t1, 25, (perf_counter * 2) + 1); /* PerfCntN */
+
+	/* Loop if it didn't */
+	uasm_il_beqz(pp, pr, t1, lbl);
+	uasm_i_nop(pp);
+
+	/* Restore perf counter 1. The count may well now be wrong... */
+	uasm_i_mtc0(pp, t2, 25, (perf_counter * 2) + 0); /* PerfCtlN */
+	uasm_i_ehb(pp);
+	uasm_i_mtc0(pp, t3, 25, (perf_counter * 2) + 1); /* PerfCntN */
+	uasm_i_ehb(pp);
+
+	return 0;
+}
+
+static void cps_gen_set_top_bit(u32 **pp, struct uasm_label **pl,
+				struct uasm_reloc **pr,
+				unsigned r_addr, int lbl)
+{
+	uasm_i_lui(pp, t0, uasm_rel_hi(0x80000000));
+	uasm_build_label(pl, *pp, lbl);
+	uasm_i_ll(pp, t1, 0, r_addr);
+	uasm_i_or(pp, t1, t1, t0);
+	uasm_i_sc(pp, t1, 0, r_addr);
+	uasm_il_beqz(pp, pr, t1, lbl);
+	uasm_i_nop(pp);
+}
+
+static void *cps_gen_entry_code(unsigned cpu, enum cps_pm_state state)
+{
+	struct uasm_label *l = labels;
+	struct uasm_reloc *r = relocs;
+	u32 *buf, *p;
+	const unsigned r_online = a0;
+	const unsigned r_nc_count = a1;
+	const unsigned r_pcohctl = t7;
+	const unsigned max_instrs = 256;
+	unsigned cpc_cmd;
+	int err;
+	enum {
+		lbl_incready = 1,
+		lbl_poll_cont,
+		lbl_secondary_hang,
+		lbl_disable_coherence,
+		lbl_flush_fsb,
+		lbl_invicache,
+		lbl_flushdcache,
+		lbl_hang,
+		lbl_set_cont,
+		lbl_secondary_cont,
+		lbl_decready,
+	};
+
+	/* Allocate a buffer to hold the generated code */
+	p = buf = kcalloc(max_instrs, sizeof(u32), GFP_KERNEL);
+	if (!buf)
+		return NULL;
+
+	/* Clear labels & relocs ready for (re)use */
+	memset(labels, 0, sizeof(labels));
+	memset(relocs, 0, sizeof(relocs));
+
+	if (IS_ENABLED(CONFIG_CPU_PM) && state == CPS_PM_POWER_GATED) {
+		/* Power gating relies upon CPS SMP */
+		if (!mips_cps_smp_in_use())
+			goto out_err;
+
+		/*
+		 * Save CPU state. Note the non-standard calling convention
+		 * with the return address placed in v0 to avoid clobbering
+		 * the ra register before it is saved.
+		 */
+		UASM_i_LA(&p, t0, (long)mips_cps_pm_save);
+		uasm_i_jalr(&p, v0, t0);
+		uasm_i_nop(&p);
+	}
+
+	/*
+	 * Load addresses of required CM & CPC registers. This is done early
+	 * because they're needed in both the enable & disable coherence steps
+	 * but in the coupled case the enable step will only run on one VPE.
+	 */
+	UASM_i_LA(&p, r_pcohctl, (long)addr_gcr_cl_coherence());
+
+	if (coupled_coherence) {
+		/* Increment ready_count */
+		uasm_i_sync(&p, __SYNC_mb);
+		uasm_build_label(&l, p, lbl_incready);
+		uasm_i_ll(&p, t1, 0, r_nc_count);
+		uasm_i_addiu(&p, t2, t1, 1);
+		uasm_i_sc(&p, t2, 0, r_nc_count);
+		uasm_il_beqz(&p, &r, t2, lbl_incready);
+		uasm_i_addiu(&p, t1, t1, 1);
+
+		/* Barrier ensuring all CPUs see the updated r_nc_count value */
+		uasm_i_sync(&p, __SYNC_mb);
+
+		/*
+		 * If this is the last VPE to become ready for non-coherence
+		 * then it should branch below.
+		 */
+		uasm_il_beq(&p, &r, t1, r_online, lbl_disable_coherence);
+		uasm_i_nop(&p);
+
+		if (state < CPS_PM_POWER_GATED) {
+			/*
+			 * Otherwise this is not the last VPE to become ready
+			 * for non-coherence. It needs to wait until coherence
+			 * has been disabled before proceeding, which it will do
+			 * by polling for the top bit of ready_count being set.
+			 */
+			uasm_i_addiu(&p, t1, zero, -1);
+			uasm_build_label(&l, p, lbl_poll_cont);
+			uasm_i_lw(&p, t0, 0, r_nc_count);
+			uasm_il_bltz(&p, &r, t0, lbl_secondary_cont);
+			uasm_i_ehb(&p);
+			if (cpu_has_mipsmt)
+				uasm_i_yield(&p, zero, t1);
+			uasm_il_b(&p, &r, lbl_poll_cont);
+			uasm_i_nop(&p);
+		} else {
+			/*
+			 * The core will lose power & this VPE will not continue
+			 * so it can simply halt here.
+			 */
+			if (cpu_has_mipsmt) {
+				/* Halt the VPE via C0 tchalt register */
+				uasm_i_addiu(&p, t0, zero, TCHALT_H);
+				uasm_i_mtc0(&p, t0, 2, 4);
+			} else if (cpu_has_vp) {
+				/* Halt the VP via the CPC VP_STOP register */
+				unsigned int vpe_id;
+
+				vpe_id = cpu_vpe_id(&cpu_data[cpu]);
+				uasm_i_addiu(&p, t0, zero, 1 << vpe_id);
+				UASM_i_LA(&p, t1, (long)addr_cpc_cl_vp_stop());
+				uasm_i_sw(&p, t0, 0, t1);
+			} else {
+				BUG();
+			}
+			uasm_build_label(&l, p, lbl_secondary_hang);
+			uasm_il_b(&p, &r, lbl_secondary_hang);
+			uasm_i_nop(&p);
+		}
+	}
+
+	/*
+	 * This is the point of no return - this VPE will now proceed to
+	 * disable coherence. At this point we *must* be sure that no other
+	 * VPE within the core will interfere with the L1 dcache.
+	 */
+	uasm_build_label(&l, p, lbl_disable_coherence);
+
+	/* Invalidate the L1 icache */
+	cps_gen_cache_routine(&p, &l, &r, &cpu_data[cpu].icache,
+			      Index_Invalidate_I, lbl_invicache);
+
+	/* Writeback & invalidate the L1 dcache */
+	cps_gen_cache_routine(&p, &l, &r, &cpu_data[cpu].dcache,
+			      Index_Writeback_Inv_D, lbl_flushdcache);
+
+	/* Barrier ensuring previous cache invalidates are complete */
+	uasm_i_sync(&p, __SYNC_full);
+	uasm_i_ehb(&p);
+
+	if (mips_cm_revision() < CM_REV_CM3) {
+		/*
+		* Disable all but self interventions. The load from COHCTL is
+		* defined by the interAptiv & proAptiv SUMs as ensuring that the
+		*  operation resulting from the preceding store is complete.
+		*/
+		uasm_i_addiu(&p, t0, zero, 1 << cpu_core(&cpu_data[cpu]));
+		uasm_i_sw(&p, t0, 0, r_pcohctl);
+		uasm_i_lw(&p, t0, 0, r_pcohctl);
+
+		/* Barrier to ensure write to coherence control is complete */
+		uasm_i_sync(&p, __SYNC_full);
+		uasm_i_ehb(&p);
+	}
+
+	/* Disable coherence */
+	uasm_i_sw(&p, zero, 0, r_pcohctl);
+	uasm_i_lw(&p, t0, 0, r_pcohctl);
+
+	if (state >= CPS_PM_CLOCK_GATED) {
+		err = cps_gen_flush_fsb(&p, &l, &r, &cpu_data[cpu],
+					lbl_flush_fsb);
+		if (err)
+			goto out_err;
+
+		/* Determine the CPC command to issue */
+		switch (state) {
+		case CPS_PM_CLOCK_GATED:
+			cpc_cmd = CPC_Cx_CMD_CLOCKOFF;
+			break;
+		case CPS_PM_POWER_GATED:
+			cpc_cmd = CPC_Cx_CMD_PWRDOWN;
+			break;
+		default:
+			BUG();
+			goto out_err;
+		}
+
+		/* Issue the CPC command */
+		UASM_i_LA(&p, t0, (long)addr_cpc_cl_cmd());
+		uasm_i_addiu(&p, t1, zero, cpc_cmd);
+		uasm_i_sw(&p, t1, 0, t0);
+
+		if (state == CPS_PM_POWER_GATED) {
+			/* If anything goes wrong just hang */
+			uasm_build_label(&l, p, lbl_hang);
+			uasm_il_b(&p, &r, lbl_hang);
+			uasm_i_nop(&p);
+
+			/*
+			 * There's no point generating more code, the core is
+			 * powered down & if powered back up will run from the
+			 * reset vector not from here.
+			 */
+			goto gen_done;
+		}
+
+		/* Barrier to ensure write to CPC command is complete */
+		uasm_i_sync(&p, __SYNC_full);
+		uasm_i_ehb(&p);
+	}
+
+	if (state == CPS_PM_NC_WAIT) {
+		/*
+		 * At this point it is safe for all VPEs to proceed with
+		 * execution. This VPE will set the top bit of ready_count
+		 * to indicate to the other VPEs that they may continue.
+		 */
+		if (coupled_coherence)
+			cps_gen_set_top_bit(&p, &l, &r, r_nc_count,
+					    lbl_set_cont);
+
+		/*
+		 * VPEs which did not disable coherence will continue
+		 * executing, after coherence has been disabled, from this
+		 * point.
+		 */
+		uasm_build_label(&l, p, lbl_secondary_cont);
+
+		/* Now perform our wait */
+		uasm_i_wait(&p, 0);
+	}
+
+	/*
+	 * Re-enable coherence. Note that for CPS_PM_NC_WAIT all coupled VPEs
+	 * will run this. The first will actually re-enable coherence & the
+	 * rest will just be performing a rather unusual nop.
+	 */
+	uasm_i_addiu(&p, t0, zero, mips_cm_revision() < CM_REV_CM3
+				? CM_GCR_Cx_COHERENCE_COHDOMAINEN
+				: CM3_GCR_Cx_COHERENCE_COHEN);
+
+	uasm_i_sw(&p, t0, 0, r_pcohctl);
+	uasm_i_lw(&p, t0, 0, r_pcohctl);
+
+	/* Barrier to ensure write to coherence control is complete */
+	uasm_i_sync(&p, __SYNC_full);
+	uasm_i_ehb(&p);
+
+	if (coupled_coherence && (state == CPS_PM_NC_WAIT)) {
+		/* Decrement ready_count */
+		uasm_build_label(&l, p, lbl_decready);
+		uasm_i_sync(&p, __SYNC_mb);
+		uasm_i_ll(&p, t1, 0, r_nc_count);
+		uasm_i_addiu(&p, t2, t1, -1);
+		uasm_i_sc(&p, t2, 0, r_nc_count);
+		uasm_il_beqz(&p, &r, t2, lbl_decready);
+		uasm_i_andi(&p, v0, t1, (1 << fls(smp_num_siblings)) - 1);
+
+		/* Barrier ensuring all CPUs see the updated r_nc_count value */
+		uasm_i_sync(&p, __SYNC_mb);
+	}
+
+	if (coupled_coherence && (state == CPS_PM_CLOCK_GATED)) {
+		/*
+		 * At this point it is safe for all VPEs to proceed with
+		 * execution. This VPE will set the top bit of ready_count
+		 * to indicate to the other VPEs that they may continue.
+		 */
+		cps_gen_set_top_bit(&p, &l, &r, r_nc_count, lbl_set_cont);
+
+		/*
+		 * This core will be reliant upon another core sending a
+		 * power-up command to the CPC in order to resume operation.
+		 * Thus an arbitrary VPE can't trigger the core leaving the
+		 * idle state and the one that disables coherence might as well
+		 * be the one to re-enable it. The rest will continue from here
+		 * after that has been done.
+		 */
+		uasm_build_label(&l, p, lbl_secondary_cont);
+
+		/* Barrier ensuring all CPUs see the updated r_nc_count value */
+		uasm_i_sync(&p, __SYNC_mb);
+	}
+
+	/* The core is coherent, time to return to C code */
+	uasm_i_jr(&p, ra);
+	uasm_i_nop(&p);
+
+gen_done:
+	/* Ensure the code didn't exceed the resources allocated for it */
+	BUG_ON((p - buf) > max_instrs);
+	BUG_ON((l - labels) > ARRAY_SIZE(labels));
+	BUG_ON((r - relocs) > ARRAY_SIZE(relocs));
+
+	/* Patch branch offsets */
+	uasm_resolve_relocs(relocs, labels);
+
+	/* Flush the icache */
+	local_flush_icache_range((unsigned long)buf, (unsigned long)p);
+
+	return buf;
+out_err:
+	kfree(buf);
+	return NULL;
+}
+
+static int cps_pm_online_cpu(unsigned int cpu)
+{
+	enum cps_pm_state state;
+	unsigned core = cpu_core(&cpu_data[cpu]);
+	void *entry_fn, *core_rc;
+
+	for (state = CPS_PM_NC_WAIT; state < CPS_PM_STATE_COUNT; state++) {
+		if (per_cpu(nc_asm_enter, core)[state])
+			continue;
+		if (!test_bit(state, state_support))
+			continue;
+
+		entry_fn = cps_gen_entry_code(cpu, state);
+		if (!entry_fn) {
+			pr_err("Failed to generate core %u state %u entry\n",
+			       core, state);
+			clear_bit(state, state_support);
+		}
+
+		per_cpu(nc_asm_enter, core)[state] = entry_fn;
+	}
+
+	if (!per_cpu(ready_count, core)) {
+		core_rc = kmalloc(sizeof(u32), GFP_KERNEL);
+		if (!core_rc) {
+			pr_err("Failed allocate core %u ready_count\n", core);
+			return -ENOMEM;
+		}
+		per_cpu(ready_count, core) = core_rc;
+	}
+
+	return 0;
+}
+
+static int cps_pm_power_notifier(struct notifier_block *this,
+				 unsigned long event, void *ptr)
+{
+	unsigned int stat;
+
+	switch (event) {
+	case PM_SUSPEND_PREPARE:
+		stat = read_cpc_cl_stat_conf();
+		/*
+		 * If we're attempting to suspend the system and power down all
+		 * of the cores, the JTAG detect bit indicates that the CPC will
+		 * instead put the cores into clock-off state. In this state
+		 * a connected debugger can cause the CPU to attempt
+		 * interactions with the powered down system. At best this will
+		 * fail. At worst, it can hang the NoC, requiring a hard reset.
+		 * To avoid this, just block system suspend if a JTAG probe
+		 * is detected.
+		 */
+		if (stat & CPC_Cx_STAT_CONF_EJTAG_PROBE) {
+			pr_warn("JTAG probe is connected - abort suspend\n");
+			return NOTIFY_BAD;
+		}
+		return NOTIFY_DONE;
+	default:
+		return NOTIFY_DONE;
+	}
+}
+
+static int __init cps_pm_init(void)
+{
+	/* A CM is required for all non-coherent states */
+	if (!mips_cm_present()) {
+		pr_warn("pm-cps: no CM, non-coherent states unavailable\n");
+		return 0;
+	}
+
+	/*
+	 * If interrupts were enabled whilst running a wait instruction on a
+	 * non-coherent core then the VPE may end up processing interrupts
+	 * whilst non-coherent. That would be bad.
+	 */
+	if (cpu_wait == r4k_wait_irqoff)
+		set_bit(CPS_PM_NC_WAIT, state_support);
+	else
+		pr_warn("pm-cps: non-coherent wait unavailable\n");
+
+	/* Detect whether a CPC is present */
+	if (mips_cpc_present()) {
+		/* Detect whether clock gating is implemented */
+		if (read_cpc_cl_stat_conf() & CPC_Cx_STAT_CONF_CLKGAT_IMPL)
+			set_bit(CPS_PM_CLOCK_GATED, state_support);
+		else
+			pr_warn("pm-cps: CPC does not support clock gating\n");
+
+		/* Power gating is available with CPS SMP & any CPC */
+		if (mips_cps_smp_in_use())
+			set_bit(CPS_PM_POWER_GATED, state_support);
+		else
+			pr_warn("pm-cps: CPS SMP not in use, power gating unavailable\n");
+	} else {
+		pr_warn("pm-cps: no CPC, clock & power gating unavailable\n");
+	}
+
+	pm_notifier(cps_pm_power_notifier, 0);
+
+	return cpuhp_setup_state(CPUHP_AP_ONLINE_DYN, "mips/cps_pm:online",
+				 cps_pm_online_cpu, NULL);
+}
+arch_initcall(cps_pm_init);
diff --git a/arch/mips/kernel/pm.c b/arch/mips/kernel/pm.c
new file mode 100644
index 000000000..486ed2bf2
--- /dev/null
+++ b/arch/mips/kernel/pm.c
@@ -0,0 +1,95 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2014 Imagination Technologies Ltd.
+ *
+ * CPU PM notifiers for saving/restoring general CPU state.
+ */
+
+#include <linux/cpu_pm.h>
+#include <linux/init.h>
+
+#include <asm/dsp.h>
+#include <asm/fpu.h>
+#include <asm/mmu_context.h>
+#include <asm/pm.h>
+#include <asm/watch.h>
+
+/* Used by PM helper macros in asm/pm.h */
+struct mips_static_suspend_state mips_static_suspend_state;
+
+/**
+ * mips_cpu_save() - Save general CPU state.
+ * Ensures that general CPU context is saved, notably FPU and DSP.
+ */
+static int mips_cpu_save(void)
+{
+	/* Save FPU state */
+	lose_fpu(1);
+
+	/* Save DSP state */
+	save_dsp(current);
+
+	return 0;
+}
+
+/**
+ * mips_cpu_restore() - Restore general CPU state.
+ * Restores important CPU context.
+ */
+static void mips_cpu_restore(void)
+{
+	unsigned int cpu = smp_processor_id();
+
+	/* Restore ASID */
+	if (current->mm)
+		write_c0_entryhi(cpu_asid(cpu, current->mm));
+
+	/* Restore DSP state */
+	restore_dsp(current);
+
+	/* Restore UserLocal */
+	if (cpu_has_userlocal)
+		write_c0_userlocal(current_thread_info()->tp_value);
+
+	/* Restore watch registers */
+	__restore_watch(current);
+}
+
+/**
+ * mips_pm_notifier() - Notifier for preserving general CPU context.
+ * @self:	Notifier block.
+ * @cmd:	CPU PM event.
+ * @v:		Private data (unused).
+ *
+ * This is called when a CPU power management event occurs, and is used to
+ * ensure that important CPU context is preserved across a CPU power down.
+ */
+static int mips_pm_notifier(struct notifier_block *self, unsigned long cmd,
+			    void *v)
+{
+	int ret;
+
+	switch (cmd) {
+	case CPU_PM_ENTER:
+		ret = mips_cpu_save();
+		if (ret)
+			return NOTIFY_STOP;
+		break;
+	case CPU_PM_ENTER_FAILED:
+	case CPU_PM_EXIT:
+		mips_cpu_restore();
+		break;
+	}
+
+	return NOTIFY_OK;
+}
+
+static struct notifier_block mips_pm_notifier_block = {
+	.notifier_call = mips_pm_notifier,
+};
+
+static int __init mips_pm_init(void)
+{
+	return cpu_pm_register_notifier(&mips_pm_notifier_block);
+}
+arch_initcall(mips_pm_init);
diff --git a/arch/mips/kernel/probes-common.h b/arch/mips/kernel/probes-common.h
new file mode 100644
index 000000000..73e1d5e95
--- /dev/null
+++ b/arch/mips/kernel/probes-common.h
@@ -0,0 +1,79 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2016 Imagination Technologies
+ * Author: Marcin Nowakowski <marcin.nowakowski@mips.com>
+ */
+
+#ifndef __PROBES_COMMON_H
+#define __PROBES_COMMON_H
+
+#include <asm/inst.h>
+
+int __insn_is_compact_branch(union mips_instruction insn);
+
+static inline int __insn_has_delay_slot(const union mips_instruction insn)
+{
+	switch (insn.i_format.opcode) {
+	/*
+	 * jr and jalr are in r_format format.
+	 */
+	case spec_op:
+		switch (insn.r_format.func) {
+		case jalr_op:
+		case jr_op:
+			return 1;
+		}
+		break;
+
+	/*
+	 * This group contains:
+	 * bltz_op, bgez_op, bltzl_op, bgezl_op,
+	 * bltzal_op, bgezal_op, bltzall_op, bgezall_op.
+	 */
+	case bcond_op:
+		switch (insn.i_format.rt) {
+		case bltz_op:
+		case bltzl_op:
+		case bgez_op:
+		case bgezl_op:
+		case bltzal_op:
+		case bltzall_op:
+		case bgezal_op:
+		case bgezall_op:
+		case bposge32_op:
+			return 1;
+		}
+		break;
+
+	/*
+	 * These are unconditional and in j_format.
+	 */
+	case jal_op:
+	case j_op:
+	case beq_op:
+	case beql_op:
+	case bne_op:
+	case bnel_op:
+	case blez_op: /* not really i_format */
+	case blezl_op:
+	case bgtz_op:
+	case bgtzl_op:
+		return 1;
+
+	/*
+	 * And now the FPA/cp1 branch instructions.
+	 */
+	case cop1_op:
+#ifdef CONFIG_CPU_CAVIUM_OCTEON
+	case lwc2_op: /* This is bbit0 on Octeon */
+	case ldc2_op: /* This is bbit032 on Octeon */
+	case swc2_op: /* This is bbit1 on Octeon */
+	case sdc2_op: /* This is bbit132 on Octeon */
+#endif
+		return 1;
+	}
+
+	return 0;
+}
+
+#endif  /* __PROBES_COMMON_H */
diff --git a/arch/mips/kernel/proc.c b/arch/mips/kernel/proc.c
new file mode 100644
index 000000000..8eba5a1ed
--- /dev/null
+++ b/arch/mips/kernel/proc.c
@@ -0,0 +1,332 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ *  Copyright (C) 1995, 1996, 2001  Ralf Baechle
+ *  Copyright (C) 2001, 2004  MIPS Technologies, Inc.
+ *  Copyright (C) 2004	Maciej W. Rozycki
+ */
+#include <linux/delay.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/seq_file.h>
+#include <asm/bootinfo.h>
+#include <asm/cpu.h>
+#include <asm/cpu-features.h>
+#include <asm/idle.h>
+#include <asm/mipsregs.h>
+#include <asm/processor.h>
+#include <asm/prom.h>
+
+unsigned int vced_count, vcei_count;
+
+/*
+ * No lock; only written during early bootup by CPU 0.
+ */
+static RAW_NOTIFIER_HEAD(proc_cpuinfo_chain);
+
+int __ref register_proc_cpuinfo_notifier(struct notifier_block *nb)
+{
+	return raw_notifier_chain_register(&proc_cpuinfo_chain, nb);
+}
+
+int proc_cpuinfo_notifier_call_chain(unsigned long val, void *v)
+{
+	return raw_notifier_call_chain(&proc_cpuinfo_chain, val, v);
+}
+
+static int show_cpuinfo(struct seq_file *m, void *v)
+{
+	struct proc_cpuinfo_notifier_args proc_cpuinfo_notifier_args;
+	unsigned long n = (unsigned long) v - 1;
+	unsigned int version = cpu_data[n].processor_id;
+	unsigned int fp_vers = cpu_data[n].fpu_id;
+	char fmt[64];
+	int i;
+
+#ifdef CONFIG_SMP
+	if (!cpu_online(n))
+		return 0;
+#endif
+
+	/*
+	 * For the first processor also print the system type
+	 */
+	if (n == 0) {
+		seq_printf(m, "system type\t\t: %s\n", get_system_type());
+		if (mips_get_machine_name())
+			seq_printf(m, "machine\t\t\t: %s\n",
+				   mips_get_machine_name());
+	}
+
+	seq_printf(m, "processor\t\t: %ld\n", n);
+	sprintf(fmt, "cpu model\t\t: %%s V%%d.%%d%s\n",
+		      cpu_data[n].options & MIPS_CPU_FPU ? "  FPU V%d.%d" : "");
+	seq_printf(m, fmt, __cpu_name[n],
+		      (version >> 4) & 0x0f, version & 0x0f,
+		      (fp_vers >> 4) & 0x0f, fp_vers & 0x0f);
+	seq_printf(m, "BogoMIPS\t\t: %u.%02u\n",
+		      cpu_data[n].udelay_val / (500000/HZ),
+		      (cpu_data[n].udelay_val / (5000/HZ)) % 100);
+	seq_printf(m, "wait instruction\t: %s\n", cpu_wait ? "yes" : "no");
+	seq_printf(m, "microsecond timers\t: %s\n",
+		      cpu_has_counter ? "yes" : "no");
+	seq_printf(m, "tlb_entries\t\t: %d\n", cpu_data[n].tlbsize);
+	seq_printf(m, "extra interrupt vector\t: %s\n",
+		      cpu_has_divec ? "yes" : "no");
+	seq_printf(m, "hardware watchpoint\t: %s",
+		      cpu_has_watch ? "yes, " : "no\n");
+	if (cpu_has_watch) {
+		seq_printf(m, "count: %d, address/irw mask: [",
+		      cpu_data[n].watch_reg_count);
+		for (i = 0; i < cpu_data[n].watch_reg_count; i++)
+			seq_printf(m, "%s0x%04x", i ? ", " : "",
+				cpu_data[n].watch_reg_masks[i]);
+		seq_puts(m, "]\n");
+	}
+
+	seq_puts(m, "isa\t\t\t:");
+	if (cpu_has_mips_1)
+		seq_puts(m, " mips1");
+	if (cpu_has_mips_2)
+		seq_puts(m, " mips2");
+	if (cpu_has_mips_3)
+		seq_puts(m, " mips3");
+	if (cpu_has_mips_4)
+		seq_puts(m, " mips4");
+	if (cpu_has_mips_5)
+		seq_puts(m, " mips5");
+	if (cpu_has_mips32r1)
+		seq_puts(m, " mips32r1");
+	if (cpu_has_mips32r2)
+		seq_puts(m, " mips32r2");
+	if (cpu_has_mips32r5)
+		seq_puts(m, " mips32r5");
+	if (cpu_has_mips32r6)
+		seq_puts(m, " mips32r6");
+	if (cpu_has_mips64r1)
+		seq_puts(m, " mips64r1");
+	if (cpu_has_mips64r2)
+		seq_puts(m, " mips64r2");
+	if (cpu_has_mips64r5)
+		seq_puts(m, " mips64r5");
+	if (cpu_has_mips64r6)
+		seq_puts(m, " mips64r6");
+	seq_puts(m, "\n");
+
+	seq_puts(m, "ASEs implemented\t:");
+	if (cpu_has_mips16)
+		seq_puts(m, " mips16");
+	if (cpu_has_mips16e2)
+		seq_puts(m, " mips16e2");
+	if (cpu_has_mdmx)
+		seq_puts(m, " mdmx");
+	if (cpu_has_mips3d)
+		seq_puts(m, " mips3d");
+	if (cpu_has_smartmips)
+		seq_puts(m, " smartmips");
+	if (cpu_has_dsp)
+		seq_puts(m, " dsp");
+	if (cpu_has_dsp2)
+		seq_puts(m, " dsp2");
+	if (cpu_has_dsp3)
+		seq_puts(m, " dsp3");
+	if (cpu_has_mipsmt)
+		seq_puts(m, " mt");
+	if (cpu_has_mmips)
+		seq_puts(m, " micromips");
+	if (cpu_has_vz)
+		seq_puts(m, " vz");
+	if (cpu_has_msa)
+		seq_puts(m, " msa");
+	if (cpu_has_eva)
+		seq_puts(m, " eva");
+	if (cpu_has_htw)
+		seq_puts(m, " htw");
+	if (cpu_has_xpa)
+		seq_puts(m, " xpa");
+	if (cpu_has_loongson_mmi)
+		seq_puts(m, " loongson-mmi");
+	if (cpu_has_loongson_cam)
+		seq_puts(m, " loongson-cam");
+	if (cpu_has_loongson_ext)
+		seq_puts(m, " loongson-ext");
+	if (cpu_has_loongson_ext2)
+		seq_puts(m, " loongson-ext2");
+	seq_puts(m, "\n");
+
+	if (cpu_has_mmips) {
+		seq_printf(m, "micromips kernel\t: %s\n",
+		      (read_c0_config3() & MIPS_CONF3_ISA_OE) ?  "yes" : "no");
+	}
+
+	seq_puts(m, "Options implemented\t:");
+	if (cpu_has_tlb)
+		seq_puts(m, " tlb");
+	if (cpu_has_ftlb)
+		seq_puts(m, " ftlb");
+	if (cpu_has_tlbinv)
+		seq_puts(m, " tlbinv");
+	if (cpu_has_segments)
+		seq_puts(m, " segments");
+	if (cpu_has_rixiex)
+		seq_puts(m, " rixiex");
+	if (cpu_has_ldpte)
+		seq_puts(m, " ldpte");
+	if (cpu_has_maar)
+		seq_puts(m, " maar");
+	if (cpu_has_rw_llb)
+		seq_puts(m, " rw_llb");
+	if (cpu_has_4kex)
+		seq_puts(m, " 4kex");
+	if (cpu_has_3k_cache)
+		seq_puts(m, " 3k_cache");
+	if (cpu_has_4k_cache)
+		seq_puts(m, " 4k_cache");
+	if (cpu_has_octeon_cache)
+		seq_puts(m, " octeon_cache");
+	if (raw_cpu_has_fpu)
+		seq_puts(m, " fpu");
+	if (cpu_has_32fpr)
+		seq_puts(m, " 32fpr");
+	if (cpu_has_cache_cdex_p)
+		seq_puts(m, " cache_cdex_p");
+	if (cpu_has_cache_cdex_s)
+		seq_puts(m, " cache_cdex_s");
+	if (cpu_has_prefetch)
+		seq_puts(m, " prefetch");
+	if (cpu_has_mcheck)
+		seq_puts(m, " mcheck");
+	if (cpu_has_ejtag)
+		seq_puts(m, " ejtag");
+	if (cpu_has_llsc)
+		seq_puts(m, " llsc");
+	if (cpu_has_guestctl0ext)
+		seq_puts(m, " guestctl0ext");
+	if (cpu_has_guestctl1)
+		seq_puts(m, " guestctl1");
+	if (cpu_has_guestctl2)
+		seq_puts(m, " guestctl2");
+	if (cpu_has_guestid)
+		seq_puts(m, " guestid");
+	if (cpu_has_drg)
+		seq_puts(m, " drg");
+	if (cpu_has_rixi)
+		seq_puts(m, " rixi");
+	if (cpu_has_lpa)
+		seq_puts(m, " lpa");
+	if (cpu_has_mvh)
+		seq_puts(m, " mvh");
+	if (cpu_has_vtag_icache)
+		seq_puts(m, " vtag_icache");
+	if (cpu_has_dc_aliases)
+		seq_puts(m, " dc_aliases");
+	if (cpu_has_ic_fills_f_dc)
+		seq_puts(m, " ic_fills_f_dc");
+	if (cpu_has_pindexed_dcache)
+		seq_puts(m, " pindexed_dcache");
+	if (cpu_has_userlocal)
+		seq_puts(m, " userlocal");
+	if (cpu_has_nofpuex)
+		seq_puts(m, " nofpuex");
+	if (cpu_has_vint)
+		seq_puts(m, " vint");
+	if (cpu_has_veic)
+		seq_puts(m, " veic");
+	if (cpu_has_inclusive_pcaches)
+		seq_puts(m, " inclusive_pcaches");
+	if (cpu_has_perf_cntr_intr_bit)
+		seq_puts(m, " perf_cntr_intr_bit");
+	if (cpu_has_ufr)
+		seq_puts(m, " ufr");
+	if (cpu_has_fre)
+		seq_puts(m, " fre");
+	if (cpu_has_cdmm)
+		seq_puts(m, " cdmm");
+	if (cpu_has_small_pages)
+		seq_puts(m, " small_pages");
+	if (cpu_has_nan_legacy)
+		seq_puts(m, " nan_legacy");
+	if (cpu_has_nan_2008)
+		seq_puts(m, " nan_2008");
+	if (cpu_has_ebase_wg)
+		seq_puts(m, " ebase_wg");
+	if (cpu_has_badinstr)
+		seq_puts(m, " badinstr");
+	if (cpu_has_badinstrp)
+		seq_puts(m, " badinstrp");
+	if (cpu_has_contextconfig)
+		seq_puts(m, " contextconfig");
+	if (cpu_has_perf)
+		seq_puts(m, " perf");
+	if (cpu_has_mac2008_only)
+		seq_puts(m, " mac2008_only");
+	if (cpu_has_ftlbparex)
+		seq_puts(m, " ftlbparex");
+	if (cpu_has_gsexcex)
+		seq_puts(m, " gsexcex");
+	if (cpu_has_shared_ftlb_ram)
+		seq_puts(m, " shared_ftlb_ram");
+	if (cpu_has_shared_ftlb_entries)
+		seq_puts(m, " shared_ftlb_entries");
+	if (cpu_has_mipsmt_pertccounters)
+		seq_puts(m, " mipsmt_pertccounters");
+	if (cpu_has_mmid)
+		seq_puts(m, " mmid");
+	if (cpu_has_mm_sysad)
+		seq_puts(m, " mm_sysad");
+	if (cpu_has_mm_full)
+		seq_puts(m, " mm_full");
+	seq_puts(m, "\n");
+
+	seq_printf(m, "shadow register sets\t: %d\n",
+		      cpu_data[n].srsets);
+	seq_printf(m, "kscratch registers\t: %d\n",
+		      hweight8(cpu_data[n].kscratch_mask));
+	seq_printf(m, "package\t\t\t: %d\n", cpu_data[n].package);
+	seq_printf(m, "core\t\t\t: %d\n", cpu_core(&cpu_data[n]));
+
+#if defined(CONFIG_MIPS_MT_SMP) || defined(CONFIG_CPU_MIPSR6)
+	if (cpu_has_mipsmt)
+		seq_printf(m, "VPE\t\t\t: %d\n", cpu_vpe_id(&cpu_data[n]));
+	else if (cpu_has_vp)
+		seq_printf(m, "VP\t\t\t: %d\n", cpu_vpe_id(&cpu_data[n]));
+#endif
+
+	sprintf(fmt, "VCE%%c exceptions\t\t: %s\n",
+		      cpu_has_vce ? "%u" : "not available");
+	seq_printf(m, fmt, 'D', vced_count);
+	seq_printf(m, fmt, 'I', vcei_count);
+
+	proc_cpuinfo_notifier_args.m = m;
+	proc_cpuinfo_notifier_args.n = n;
+
+	raw_notifier_call_chain(&proc_cpuinfo_chain, 0,
+				&proc_cpuinfo_notifier_args);
+
+	seq_puts(m, "\n");
+
+	return 0;
+}
+
+static void *c_start(struct seq_file *m, loff_t *pos)
+{
+	unsigned long i = *pos;
+
+	return i < nr_cpu_ids ? (void *) (i + 1) : NULL;
+}
+
+static void *c_next(struct seq_file *m, void *v, loff_t *pos)
+{
+	++*pos;
+	return c_start(m, pos);
+}
+
+static void c_stop(struct seq_file *m, void *v)
+{
+}
+
+const struct seq_operations cpuinfo_op = {
+	.start	= c_start,
+	.next	= c_next,
+	.stop	= c_stop,
+	.show	= show_cpuinfo,
+};
diff --git a/arch/mips/kernel/process.c b/arch/mips/kernel/process.c
new file mode 100644
index 000000000..17d80e2f2
--- /dev/null
+++ b/arch/mips/kernel/process.c
@@ -0,0 +1,912 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994 - 1999, 2000 by Ralf Baechle and others.
+ * Copyright (C) 2005, 2006 by Ralf Baechle (ralf@linux-mips.org)
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ * Copyright (C) 2004 Thiemo Seufer
+ * Copyright (C) 2013  Imagination Technologies Ltd.
+ */
+#include <linux/cpu.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/kallsyms.h>
+#include <linux/kernel.h>
+#include <linux/nmi.h>
+#include <linux/personality.h>
+#include <linux/prctl.h>
+#include <linux/random.h>
+#include <linux/sched.h>
+#include <linux/sched/debug.h>
+#include <linux/sched/task_stack.h>
+
+#include <asm/abi.h>
+#include <asm/asm.h>
+#include <asm/dsemul.h>
+#include <asm/dsp.h>
+#include <asm/exec.h>
+#include <asm/fpu.h>
+#include <asm/inst.h>
+#include <asm/irq.h>
+#include <asm/irq_regs.h>
+#include <asm/isadep.h>
+#include <asm/msa.h>
+#include <asm/mips-cps.h>
+#include <asm/mipsregs.h>
+#include <asm/processor.h>
+#include <asm/reg.h>
+#include <asm/stacktrace.h>
+
+#ifdef CONFIG_HOTPLUG_CPU
+void arch_cpu_idle_dead(void)
+{
+	play_dead();
+}
+#endif
+
+asmlinkage void ret_from_fork(void);
+asmlinkage void ret_from_kernel_thread(void);
+
+void start_thread(struct pt_regs * regs, unsigned long pc, unsigned long sp)
+{
+	unsigned long status;
+
+	/* New thread loses kernel privileges. */
+	status = regs->cp0_status & ~(ST0_CU0|ST0_CU1|ST0_CU2|ST0_FR|KU_MASK);
+	status |= KU_USER;
+	regs->cp0_status = status;
+	lose_fpu(0);
+	clear_thread_flag(TIF_MSA_CTX_LIVE);
+	clear_used_math();
+#ifdef CONFIG_MIPS_FP_SUPPORT
+	atomic_set(&current->thread.bd_emu_frame, BD_EMUFRAME_NONE);
+#endif
+	init_dsp();
+	regs->cp0_epc = pc;
+	regs->regs[29] = sp;
+}
+
+void exit_thread(struct task_struct *tsk)
+{
+	/*
+	 * User threads may have allocated a delay slot emulation frame.
+	 * If so, clean up that allocation.
+	 */
+	if (!(current->flags & PF_KTHREAD))
+		dsemul_thread_cleanup(tsk);
+}
+
+int arch_dup_task_struct(struct task_struct *dst, struct task_struct *src)
+{
+	/*
+	 * Save any process state which is live in hardware registers to the
+	 * parent context prior to duplication. This prevents the new child
+	 * state becoming stale if the parent is preempted before copy_thread()
+	 * gets a chance to save the parent's live hardware registers to the
+	 * child context.
+	 */
+	preempt_disable();
+
+	if (is_msa_enabled())
+		save_msa(current);
+	else if (is_fpu_owner())
+		_save_fp(current);
+
+	save_dsp(current);
+
+	preempt_enable();
+
+	*dst = *src;
+	return 0;
+}
+
+/*
+ * Copy architecture-specific thread state
+ */
+int copy_thread(struct task_struct *p, const struct kernel_clone_args *args)
+{
+	unsigned long clone_flags = args->flags;
+	unsigned long usp = args->stack;
+	unsigned long tls = args->tls;
+	struct thread_info *ti = task_thread_info(p);
+	struct pt_regs *childregs, *regs = current_pt_regs();
+	unsigned long childksp;
+
+	childksp = (unsigned long)task_stack_page(p) + THREAD_SIZE - 32;
+
+	/* set up new TSS. */
+	childregs = (struct pt_regs *) childksp - 1;
+	/*  Put the stack after the struct pt_regs.  */
+	childksp = (unsigned long) childregs;
+	p->thread.cp0_status = (read_c0_status() & ~(ST0_CU2|ST0_CU1)) | ST0_KERNEL_CUMASK;
+
+	/*
+	 * New tasks lose permission to use the fpu. This accelerates context
+	 * switching for most programs since they don't use the fpu.
+	 */
+	clear_tsk_thread_flag(p, TIF_USEDFPU);
+	clear_tsk_thread_flag(p, TIF_USEDMSA);
+	clear_tsk_thread_flag(p, TIF_MSA_CTX_LIVE);
+
+#ifdef CONFIG_MIPS_MT_FPAFF
+	clear_tsk_thread_flag(p, TIF_FPUBOUND);
+#endif /* CONFIG_MIPS_MT_FPAFF */
+
+	if (unlikely(args->fn)) {
+		/* kernel thread */
+		unsigned long status = p->thread.cp0_status;
+		memset(childregs, 0, sizeof(struct pt_regs));
+		p->thread.reg16 = (unsigned long)args->fn;
+		p->thread.reg17 = (unsigned long)args->fn_arg;
+		p->thread.reg29 = childksp;
+		p->thread.reg31 = (unsigned long) ret_from_kernel_thread;
+#if defined(CONFIG_CPU_R3000)
+		status = (status & ~(ST0_KUP | ST0_IEP | ST0_IEC)) |
+			 ((status & (ST0_KUC | ST0_IEC)) << 2);
+#else
+		status |= ST0_EXL;
+#endif
+		childregs->cp0_status = status;
+		return 0;
+	}
+
+	/* user thread */
+	*childregs = *regs;
+	childregs->regs[7] = 0; /* Clear error flag */
+	childregs->regs[2] = 0; /* Child gets zero as return value */
+	if (usp)
+		childregs->regs[29] = usp;
+
+	p->thread.reg29 = (unsigned long) childregs;
+	p->thread.reg31 = (unsigned long) ret_from_fork;
+
+	childregs->cp0_status &= ~(ST0_CU2|ST0_CU1);
+
+#ifdef CONFIG_MIPS_FP_SUPPORT
+	atomic_set(&p->thread.bd_emu_frame, BD_EMUFRAME_NONE);
+#endif
+
+	if (clone_flags & CLONE_SETTLS)
+		ti->tp_value = tls;
+
+	return 0;
+}
+
+#ifdef CONFIG_STACKPROTECTOR
+#include <linux/stackprotector.h>
+unsigned long __stack_chk_guard __read_mostly;
+EXPORT_SYMBOL(__stack_chk_guard);
+#endif
+
+struct mips_frame_info {
+	void		*func;
+	unsigned long	func_size;
+	int		frame_size;
+	int		pc_offset;
+};
+
+#define J_TARGET(pc,target)	\
+		(((unsigned long)(pc) & 0xf0000000) | ((target) << 2))
+
+static inline int is_jr_ra_ins(union mips_instruction *ip)
+{
+#ifdef CONFIG_CPU_MICROMIPS
+	/*
+	 * jr16 ra
+	 * jr ra
+	 */
+	if (mm_insn_16bit(ip->word >> 16)) {
+		if (ip->mm16_r5_format.opcode == mm_pool16c_op &&
+		    ip->mm16_r5_format.rt == mm_jr16_op &&
+		    ip->mm16_r5_format.imm == 31)
+			return 1;
+		return 0;
+	}
+
+	if (ip->r_format.opcode == mm_pool32a_op &&
+	    ip->r_format.func == mm_pool32axf_op &&
+	    ((ip->u_format.uimmediate >> 6) & GENMASK(9, 0)) == mm_jalr_op &&
+	    ip->r_format.rt == 31)
+		return 1;
+	return 0;
+#else
+	if (ip->r_format.opcode == spec_op &&
+	    ip->r_format.func == jr_op &&
+	    ip->r_format.rs == 31)
+		return 1;
+	return 0;
+#endif
+}
+
+static inline int is_ra_save_ins(union mips_instruction *ip, int *poff)
+{
+#ifdef CONFIG_CPU_MICROMIPS
+	/*
+	 * swsp ra,offset
+	 * swm16 reglist,offset(sp)
+	 * swm32 reglist,offset(sp)
+	 * sw32 ra,offset(sp)
+	 * jradiussp - NOT SUPPORTED
+	 *
+	 * microMIPS is way more fun...
+	 */
+	if (mm_insn_16bit(ip->word >> 16)) {
+		switch (ip->mm16_r5_format.opcode) {
+		case mm_swsp16_op:
+			if (ip->mm16_r5_format.rt != 31)
+				return 0;
+
+			*poff = ip->mm16_r5_format.imm;
+			*poff = (*poff << 2) / sizeof(ulong);
+			return 1;
+
+		case mm_pool16c_op:
+			switch (ip->mm16_m_format.func) {
+			case mm_swm16_op:
+				*poff = ip->mm16_m_format.imm;
+				*poff += 1 + ip->mm16_m_format.rlist;
+				*poff = (*poff << 2) / sizeof(ulong);
+				return 1;
+
+			default:
+				return 0;
+			}
+
+		default:
+			return 0;
+		}
+	}
+
+	switch (ip->i_format.opcode) {
+	case mm_sw32_op:
+		if (ip->i_format.rs != 29)
+			return 0;
+		if (ip->i_format.rt != 31)
+			return 0;
+
+		*poff = ip->i_format.simmediate / sizeof(ulong);
+		return 1;
+
+	case mm_pool32b_op:
+		switch (ip->mm_m_format.func) {
+		case mm_swm32_func:
+			if (ip->mm_m_format.rd < 0x10)
+				return 0;
+			if (ip->mm_m_format.base != 29)
+				return 0;
+
+			*poff = ip->mm_m_format.simmediate;
+			*poff += (ip->mm_m_format.rd & 0xf) * sizeof(u32);
+			*poff /= sizeof(ulong);
+			return 1;
+		default:
+			return 0;
+		}
+
+	default:
+		return 0;
+	}
+#else
+	/* sw / sd $ra, offset($sp) */
+	if ((ip->i_format.opcode == sw_op || ip->i_format.opcode == sd_op) &&
+		ip->i_format.rs == 29 && ip->i_format.rt == 31) {
+		*poff = ip->i_format.simmediate / sizeof(ulong);
+		return 1;
+	}
+#ifdef CONFIG_CPU_LOONGSON64
+	if ((ip->loongson3_lswc2_format.opcode == swc2_op) &&
+		      (ip->loongson3_lswc2_format.ls == 1) &&
+		      (ip->loongson3_lswc2_format.fr == 0) &&
+		      (ip->loongson3_lswc2_format.base == 29)) {
+		if (ip->loongson3_lswc2_format.rt == 31) {
+			*poff = ip->loongson3_lswc2_format.offset << 1;
+			return 1;
+		}
+		if (ip->loongson3_lswc2_format.rq == 31) {
+			*poff = (ip->loongson3_lswc2_format.offset << 1) + 1;
+			return 1;
+		}
+	}
+#endif
+	return 0;
+#endif
+}
+
+static inline int is_jump_ins(union mips_instruction *ip)
+{
+#ifdef CONFIG_CPU_MICROMIPS
+	/*
+	 * jr16,jrc,jalr16,jalr16
+	 * jal
+	 * jalr/jr,jalr.hb/jr.hb,jalrs,jalrs.hb
+	 * jraddiusp - NOT SUPPORTED
+	 *
+	 * microMIPS is kind of more fun...
+	 */
+	if (mm_insn_16bit(ip->word >> 16)) {
+		if ((ip->mm16_r5_format.opcode == mm_pool16c_op &&
+		    (ip->mm16_r5_format.rt & mm_jr16_op) == mm_jr16_op))
+			return 1;
+		return 0;
+	}
+
+	if (ip->j_format.opcode == mm_j32_op)
+		return 1;
+	if (ip->j_format.opcode == mm_jal32_op)
+		return 1;
+	if (ip->r_format.opcode != mm_pool32a_op ||
+			ip->r_format.func != mm_pool32axf_op)
+		return 0;
+	return ((ip->u_format.uimmediate >> 6) & mm_jalr_op) == mm_jalr_op;
+#else
+	if (ip->j_format.opcode == j_op)
+		return 1;
+	if (ip->j_format.opcode == jal_op)
+		return 1;
+	if (ip->r_format.opcode != spec_op)
+		return 0;
+	return ip->r_format.func == jalr_op || ip->r_format.func == jr_op;
+#endif
+}
+
+static inline int is_sp_move_ins(union mips_instruction *ip, int *frame_size)
+{
+#ifdef CONFIG_CPU_MICROMIPS
+	unsigned short tmp;
+
+	/*
+	 * addiusp -imm
+	 * addius5 sp,-imm
+	 * addiu32 sp,sp,-imm
+	 * jradiussp - NOT SUPPORTED
+	 *
+	 * microMIPS is not more fun...
+	 */
+	if (mm_insn_16bit(ip->word >> 16)) {
+		if (ip->mm16_r3_format.opcode == mm_pool16d_op &&
+		    ip->mm16_r3_format.simmediate & mm_addiusp_func) {
+			tmp = ip->mm_b0_format.simmediate >> 1;
+			tmp = ((tmp & 0x1ff) ^ 0x100) - 0x100;
+			if ((tmp + 2) < 4) /* 0x0,0x1,0x1fe,0x1ff are special */
+				tmp ^= 0x100;
+			*frame_size = -(signed short)(tmp << 2);
+			return 1;
+		}
+		if (ip->mm16_r5_format.opcode == mm_pool16d_op &&
+		    ip->mm16_r5_format.rt == 29) {
+			tmp = ip->mm16_r5_format.imm >> 1;
+			*frame_size = -(signed short)(tmp & 0xf);
+			return 1;
+		}
+		return 0;
+	}
+
+	if (ip->mm_i_format.opcode == mm_addiu32_op &&
+	    ip->mm_i_format.rt == 29 && ip->mm_i_format.rs == 29) {
+		*frame_size = -ip->i_format.simmediate;
+		return 1;
+	}
+#else
+	/* addiu/daddiu sp,sp,-imm */
+	if (ip->i_format.rs != 29 || ip->i_format.rt != 29)
+		return 0;
+
+	if (ip->i_format.opcode == addiu_op ||
+	    ip->i_format.opcode == daddiu_op) {
+		*frame_size = -ip->i_format.simmediate;
+		return 1;
+	}
+#endif
+	return 0;
+}
+
+static int get_frame_info(struct mips_frame_info *info)
+{
+	bool is_mmips = IS_ENABLED(CONFIG_CPU_MICROMIPS);
+	union mips_instruction insn, *ip, *ip_end;
+	unsigned int last_insn_size = 0;
+	bool saw_jump = false;
+
+	info->pc_offset = -1;
+	info->frame_size = 0;
+
+	ip = (void *)msk_isa16_mode((ulong)info->func);
+	if (!ip)
+		goto err;
+
+	ip_end = (void *)ip + (info->func_size ? info->func_size : 512);
+
+	while (ip < ip_end) {
+		ip = (void *)ip + last_insn_size;
+
+		if (is_mmips && mm_insn_16bit(ip->halfword[0])) {
+			insn.word = ip->halfword[0] << 16;
+			last_insn_size = 2;
+		} else if (is_mmips) {
+			insn.word = ip->halfword[0] << 16 | ip->halfword[1];
+			last_insn_size = 4;
+		} else {
+			insn.word = ip->word;
+			last_insn_size = 4;
+		}
+
+		if (is_jr_ra_ins(ip)) {
+			break;
+		} else if (!info->frame_size) {
+			is_sp_move_ins(&insn, &info->frame_size);
+			continue;
+		} else if (!saw_jump && is_jump_ins(ip)) {
+			/*
+			 * If we see a jump instruction, we are finished
+			 * with the frame save.
+			 *
+			 * Some functions can have a shortcut return at
+			 * the beginning of the function, so don't start
+			 * looking for jump instruction until we see the
+			 * frame setup.
+			 *
+			 * The RA save instruction can get put into the
+			 * delay slot of the jump instruction, so look
+			 * at the next instruction, too.
+			 */
+			saw_jump = true;
+			continue;
+		}
+		if (info->pc_offset == -1 &&
+		    is_ra_save_ins(&insn, &info->pc_offset))
+			break;
+		if (saw_jump)
+			break;
+	}
+	if (info->frame_size && info->pc_offset >= 0) /* nested */
+		return 0;
+	if (info->pc_offset < 0) /* leaf */
+		return 1;
+	/* prologue seems bogus... */
+err:
+	return -1;
+}
+
+static struct mips_frame_info schedule_mfi __read_mostly;
+
+#ifdef CONFIG_KALLSYMS
+static unsigned long get___schedule_addr(void)
+{
+	return kallsyms_lookup_name("__schedule");
+}
+#else
+static unsigned long get___schedule_addr(void)
+{
+	union mips_instruction *ip = (void *)schedule;
+	int max_insns = 8;
+	int i;
+
+	for (i = 0; i < max_insns; i++, ip++) {
+		if (ip->j_format.opcode == j_op)
+			return J_TARGET(ip, ip->j_format.target);
+	}
+	return 0;
+}
+#endif
+
+static int __init frame_info_init(void)
+{
+	unsigned long size = 0;
+#ifdef CONFIG_KALLSYMS
+	unsigned long ofs;
+#endif
+	unsigned long addr;
+
+	addr = get___schedule_addr();
+	if (!addr)
+		addr = (unsigned long)schedule;
+
+#ifdef CONFIG_KALLSYMS
+	kallsyms_lookup_size_offset(addr, &size, &ofs);
+#endif
+	schedule_mfi.func = (void *)addr;
+	schedule_mfi.func_size = size;
+
+	get_frame_info(&schedule_mfi);
+
+	/*
+	 * Without schedule() frame info, result given by
+	 * thread_saved_pc() and __get_wchan() are not reliable.
+	 */
+	if (schedule_mfi.pc_offset < 0)
+		printk("Can't analyze schedule() prologue at %p\n", schedule);
+
+	return 0;
+}
+
+arch_initcall(frame_info_init);
+
+/*
+ * Return saved PC of a blocked thread.
+ */
+static unsigned long thread_saved_pc(struct task_struct *tsk)
+{
+	struct thread_struct *t = &tsk->thread;
+
+	/* New born processes are a special case */
+	if (t->reg31 == (unsigned long) ret_from_fork)
+		return t->reg31;
+	if (schedule_mfi.pc_offset < 0)
+		return 0;
+	return ((unsigned long *)t->reg29)[schedule_mfi.pc_offset];
+}
+
+
+#ifdef CONFIG_KALLSYMS
+/* generic stack unwinding function */
+unsigned long notrace unwind_stack_by_address(unsigned long stack_page,
+					      unsigned long *sp,
+					      unsigned long pc,
+					      unsigned long *ra)
+{
+	unsigned long low, high, irq_stack_high;
+	struct mips_frame_info info;
+	unsigned long size, ofs;
+	struct pt_regs *regs;
+	int leaf;
+
+	if (!stack_page)
+		return 0;
+
+	/*
+	 * IRQ stacks start at IRQ_STACK_START
+	 * task stacks at THREAD_SIZE - 32
+	 */
+	low = stack_page;
+	if (!preemptible() && on_irq_stack(raw_smp_processor_id(), *sp)) {
+		high = stack_page + IRQ_STACK_START;
+		irq_stack_high = high;
+	} else {
+		high = stack_page + THREAD_SIZE - 32;
+		irq_stack_high = 0;
+	}
+
+	/*
+	 * If we reached the top of the interrupt stack, start unwinding
+	 * the interrupted task stack.
+	 */
+	if (unlikely(*sp == irq_stack_high)) {
+		unsigned long task_sp = *(unsigned long *)*sp;
+
+		/*
+		 * Check that the pointer saved in the IRQ stack head points to
+		 * something within the stack of the current task
+		 */
+		if (!object_is_on_stack((void *)task_sp))
+			return 0;
+
+		/*
+		 * Follow pointer to tasks kernel stack frame where interrupted
+		 * state was saved.
+		 */
+		regs = (struct pt_regs *)task_sp;
+		pc = regs->cp0_epc;
+		if (!user_mode(regs) && __kernel_text_address(pc)) {
+			*sp = regs->regs[29];
+			*ra = regs->regs[31];
+			return pc;
+		}
+		return 0;
+	}
+	if (!kallsyms_lookup_size_offset(pc, &size, &ofs))
+		return 0;
+	/*
+	 * Return ra if an exception occurred at the first instruction
+	 */
+	if (unlikely(ofs == 0)) {
+		pc = *ra;
+		*ra = 0;
+		return pc;
+	}
+
+	info.func = (void *)(pc - ofs);
+	info.func_size = ofs;	/* analyze from start to ofs */
+	leaf = get_frame_info(&info);
+	if (leaf < 0)
+		return 0;
+
+	if (*sp < low || *sp + info.frame_size > high)
+		return 0;
+
+	if (leaf)
+		/*
+		 * For some extreme cases, get_frame_info() can
+		 * consider wrongly a nested function as a leaf
+		 * one. In that cases avoid to return always the
+		 * same value.
+		 */
+		pc = pc != *ra ? *ra : 0;
+	else
+		pc = ((unsigned long *)(*sp))[info.pc_offset];
+
+	*sp += info.frame_size;
+	*ra = 0;
+	return __kernel_text_address(pc) ? pc : 0;
+}
+EXPORT_SYMBOL(unwind_stack_by_address);
+
+/* used by show_backtrace() */
+unsigned long unwind_stack(struct task_struct *task, unsigned long *sp,
+			   unsigned long pc, unsigned long *ra)
+{
+	unsigned long stack_page = 0;
+	int cpu;
+
+	for_each_possible_cpu(cpu) {
+		if (on_irq_stack(cpu, *sp)) {
+			stack_page = (unsigned long)irq_stack[cpu];
+			break;
+		}
+	}
+
+	if (!stack_page)
+		stack_page = (unsigned long)task_stack_page(task);
+
+	return unwind_stack_by_address(stack_page, sp, pc, ra);
+}
+#endif
+
+/*
+ * __get_wchan - a maintenance nightmare^W^Wpain in the ass ...
+ */
+unsigned long __get_wchan(struct task_struct *task)
+{
+	unsigned long pc = 0;
+#ifdef CONFIG_KALLSYMS
+	unsigned long sp;
+	unsigned long ra = 0;
+#endif
+
+	if (!task_stack_page(task))
+		goto out;
+
+	pc = thread_saved_pc(task);
+
+#ifdef CONFIG_KALLSYMS
+	sp = task->thread.reg29 + schedule_mfi.frame_size;
+
+	while (in_sched_functions(pc))
+		pc = unwind_stack(task, &sp, pc, &ra);
+#endif
+
+out:
+	return pc;
+}
+
+unsigned long mips_stack_top(void)
+{
+	unsigned long top = TASK_SIZE & PAGE_MASK;
+
+	if (IS_ENABLED(CONFIG_MIPS_FP_SUPPORT)) {
+		/* One page for branch delay slot "emulation" */
+		top -= PAGE_SIZE;
+	}
+
+	/* Space for the VDSO, data page & GIC user page */
+	top -= PAGE_ALIGN(current->thread.abi->vdso->size);
+	top -= PAGE_SIZE;
+	top -= mips_gic_present() ? PAGE_SIZE : 0;
+
+	/* Space for cache colour alignment */
+	if (cpu_has_dc_aliases)
+		top -= shm_align_mask + 1;
+
+	/* Space to randomize the VDSO base */
+	if (current->flags & PF_RANDOMIZE)
+		top -= VDSO_RANDOMIZE_SIZE;
+
+	return top;
+}
+
+/*
+ * Don't forget that the stack pointer must be aligned on a 8 bytes
+ * boundary for 32-bits ABI and 16 bytes for 64-bits ABI.
+ */
+unsigned long arch_align_stack(unsigned long sp)
+{
+	if (!(current->personality & ADDR_NO_RANDOMIZE) && randomize_va_space)
+		sp -= prandom_u32_max(PAGE_SIZE);
+
+	return sp & ALMASK;
+}
+
+static struct cpumask backtrace_csd_busy;
+
+static void handle_backtrace(void *info)
+{
+	nmi_cpu_backtrace(get_irq_regs());
+	cpumask_clear_cpu(smp_processor_id(), &backtrace_csd_busy);
+}
+
+static DEFINE_PER_CPU(call_single_data_t, backtrace_csd) =
+	CSD_INIT(handle_backtrace, NULL);
+
+static void raise_backtrace(cpumask_t *mask)
+{
+	call_single_data_t *csd;
+	int cpu;
+
+	for_each_cpu(cpu, mask) {
+		/*
+		 * If we previously sent an IPI to the target CPU & it hasn't
+		 * cleared its bit in the busy cpumask then it didn't handle
+		 * our previous IPI & it's not safe for us to reuse the
+		 * call_single_data_t.
+		 */
+		if (cpumask_test_and_set_cpu(cpu, &backtrace_csd_busy)) {
+			pr_warn("Unable to send backtrace IPI to CPU%u - perhaps it hung?\n",
+				cpu);
+			continue;
+		}
+
+		csd = &per_cpu(backtrace_csd, cpu);
+		smp_call_function_single_async(cpu, csd);
+	}
+}
+
+void arch_trigger_cpumask_backtrace(const cpumask_t *mask, bool exclude_self)
+{
+	nmi_trigger_cpumask_backtrace(mask, exclude_self, raise_backtrace);
+}
+
+int mips_get_process_fp_mode(struct task_struct *task)
+{
+	int value = 0;
+
+	if (!test_tsk_thread_flag(task, TIF_32BIT_FPREGS))
+		value |= PR_FP_MODE_FR;
+	if (test_tsk_thread_flag(task, TIF_HYBRID_FPREGS))
+		value |= PR_FP_MODE_FRE;
+
+	return value;
+}
+
+static long prepare_for_fp_mode_switch(void *unused)
+{
+	/*
+	 * This is icky, but we use this to simply ensure that all CPUs have
+	 * context switched, regardless of whether they were previously running
+	 * kernel or user code. This ensures that no CPU that a mode-switching
+	 * program may execute on keeps its FPU enabled (& in the old mode)
+	 * throughout the mode switch.
+	 */
+	return 0;
+}
+
+int mips_set_process_fp_mode(struct task_struct *task, unsigned int value)
+{
+	const unsigned int known_bits = PR_FP_MODE_FR | PR_FP_MODE_FRE;
+	struct task_struct *t;
+	struct cpumask process_cpus;
+	int cpu;
+
+	/* If nothing to change, return right away, successfully.  */
+	if (value == mips_get_process_fp_mode(task))
+		return 0;
+
+	/* Only accept a mode change if 64-bit FP enabled for o32.  */
+	if (!IS_ENABLED(CONFIG_MIPS_O32_FP64_SUPPORT))
+		return -EOPNOTSUPP;
+
+	/* And only for o32 tasks.  */
+	if (IS_ENABLED(CONFIG_64BIT) && !test_thread_flag(TIF_32BIT_REGS))
+		return -EOPNOTSUPP;
+
+	/* Check the value is valid */
+	if (value & ~known_bits)
+		return -EOPNOTSUPP;
+
+	/* Setting FRE without FR is not supported.  */
+	if ((value & (PR_FP_MODE_FR | PR_FP_MODE_FRE)) == PR_FP_MODE_FRE)
+		return -EOPNOTSUPP;
+
+	/* Avoid inadvertently triggering emulation */
+	if ((value & PR_FP_MODE_FR) && raw_cpu_has_fpu &&
+	    !(raw_current_cpu_data.fpu_id & MIPS_FPIR_F64))
+		return -EOPNOTSUPP;
+	if ((value & PR_FP_MODE_FRE) && raw_cpu_has_fpu && !cpu_has_fre)
+		return -EOPNOTSUPP;
+
+	/* FR = 0 not supported in MIPS R6 */
+	if (!(value & PR_FP_MODE_FR) && raw_cpu_has_fpu && cpu_has_mips_r6)
+		return -EOPNOTSUPP;
+
+	/* Indicate the new FP mode in each thread */
+	for_each_thread(task, t) {
+		/* Update desired FP register width */
+		if (value & PR_FP_MODE_FR) {
+			clear_tsk_thread_flag(t, TIF_32BIT_FPREGS);
+		} else {
+			set_tsk_thread_flag(t, TIF_32BIT_FPREGS);
+			clear_tsk_thread_flag(t, TIF_MSA_CTX_LIVE);
+		}
+
+		/* Update desired FP single layout */
+		if (value & PR_FP_MODE_FRE)
+			set_tsk_thread_flag(t, TIF_HYBRID_FPREGS);
+		else
+			clear_tsk_thread_flag(t, TIF_HYBRID_FPREGS);
+	}
+
+	/*
+	 * We need to ensure that all threads in the process have switched mode
+	 * before returning, in order to allow userland to not worry about
+	 * races. We can do this by forcing all CPUs that any thread in the
+	 * process may be running on to schedule something else - in this case
+	 * prepare_for_fp_mode_switch().
+	 *
+	 * We begin by generating a mask of all CPUs that any thread in the
+	 * process may be running on.
+	 */
+	cpumask_clear(&process_cpus);
+	for_each_thread(task, t)
+		cpumask_set_cpu(task_cpu(t), &process_cpus);
+
+	/*
+	 * Now we schedule prepare_for_fp_mode_switch() on each of those CPUs.
+	 *
+	 * The CPUs may have rescheduled already since we switched mode or
+	 * generated the cpumask, but that doesn't matter. If the task in this
+	 * process is scheduled out then our scheduling
+	 * prepare_for_fp_mode_switch() will simply be redundant. If it's
+	 * scheduled in then it will already have picked up the new FP mode
+	 * whilst doing so.
+	 */
+	cpus_read_lock();
+	for_each_cpu_and(cpu, &process_cpus, cpu_online_mask)
+		work_on_cpu(cpu, prepare_for_fp_mode_switch, NULL);
+	cpus_read_unlock();
+
+	return 0;
+}
+
+#if defined(CONFIG_32BIT) || defined(CONFIG_MIPS32_O32)
+void mips_dump_regs32(u32 *uregs, const struct pt_regs *regs)
+{
+	unsigned int i;
+
+	for (i = MIPS32_EF_R1; i <= MIPS32_EF_R31; i++) {
+		/* k0/k1 are copied as zero. */
+		if (i == MIPS32_EF_R26 || i == MIPS32_EF_R27)
+			uregs[i] = 0;
+		else
+			uregs[i] = regs->regs[i - MIPS32_EF_R0];
+	}
+
+	uregs[MIPS32_EF_LO] = regs->lo;
+	uregs[MIPS32_EF_HI] = regs->hi;
+	uregs[MIPS32_EF_CP0_EPC] = regs->cp0_epc;
+	uregs[MIPS32_EF_CP0_BADVADDR] = regs->cp0_badvaddr;
+	uregs[MIPS32_EF_CP0_STATUS] = regs->cp0_status;
+	uregs[MIPS32_EF_CP0_CAUSE] = regs->cp0_cause;
+}
+#endif /* CONFIG_32BIT || CONFIG_MIPS32_O32 */
+
+#ifdef CONFIG_64BIT
+void mips_dump_regs64(u64 *uregs, const struct pt_regs *regs)
+{
+	unsigned int i;
+
+	for (i = MIPS64_EF_R1; i <= MIPS64_EF_R31; i++) {
+		/* k0/k1 are copied as zero. */
+		if (i == MIPS64_EF_R26 || i == MIPS64_EF_R27)
+			uregs[i] = 0;
+		else
+			uregs[i] = regs->regs[i - MIPS64_EF_R0];
+	}
+
+	uregs[MIPS64_EF_LO] = regs->lo;
+	uregs[MIPS64_EF_HI] = regs->hi;
+	uregs[MIPS64_EF_CP0_EPC] = regs->cp0_epc;
+	uregs[MIPS64_EF_CP0_BADVADDR] = regs->cp0_badvaddr;
+	uregs[MIPS64_EF_CP0_STATUS] = regs->cp0_status;
+	uregs[MIPS64_EF_CP0_CAUSE] = regs->cp0_cause;
+}
+#endif /* CONFIG_64BIT */
diff --git a/arch/mips/kernel/prom.c b/arch/mips/kernel/prom.c
new file mode 100644
index 000000000..f88ce78e1
--- /dev/null
+++ b/arch/mips/kernel/prom.c
@@ -0,0 +1,72 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * MIPS support for CONFIG_OF device tree support
+ *
+ * Copyright (C) 2010 Cisco Systems Inc. <dediao@cisco.com>
+ */
+
+#include <linux/init.h>
+#include <linux/export.h>
+#include <linux/errno.h>
+#include <linux/types.h>
+#include <linux/memblock.h>
+#include <linux/debugfs.h>
+#include <linux/of.h>
+#include <linux/of_fdt.h>
+#include <linux/of_platform.h>
+
+#include <asm/bootinfo.h>
+#include <asm/page.h>
+#include <asm/prom.h>
+
+static char mips_machine_name[64] = "Unknown";
+
+__init void mips_set_machine_name(const char *name)
+{
+	if (name == NULL)
+		return;
+
+	strscpy(mips_machine_name, name, sizeof(mips_machine_name));
+	pr_info("MIPS: machine is %s\n", mips_get_machine_name());
+}
+
+char *mips_get_machine_name(void)
+{
+	return mips_machine_name;
+}
+
+#ifdef CONFIG_USE_OF
+
+void __init __dt_setup_arch(void *bph)
+{
+	if (!early_init_dt_scan(bph))
+		return;
+
+	mips_set_machine_name(of_flat_dt_get_machine_name());
+}
+
+int __init __dt_register_buses(const char *bus0, const char *bus1)
+{
+	static struct of_device_id of_ids[3];
+
+	if (!of_have_populated_dt())
+		panic("device tree not present");
+
+	strscpy(of_ids[0].compatible, bus0, sizeof(of_ids[0].compatible));
+	if (bus1) {
+		strscpy(of_ids[1].compatible, bus1,
+			sizeof(of_ids[1].compatible));
+	}
+
+	if (of_platform_populate(NULL, of_ids, NULL, NULL))
+		panic("failed to populate DT");
+
+	return 0;
+}
+
+void __weak __init device_tree_init(void)
+{
+	unflatten_and_copy_device_tree();
+}
+
+#endif
diff --git a/arch/mips/kernel/ptrace.c b/arch/mips/kernel/ptrace.c
new file mode 100644
index 000000000..567aec4ab
--- /dev/null
+++ b/arch/mips/kernel/ptrace.c
@@ -0,0 +1,1381 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1992 Ross Biro
+ * Copyright (C) Linus Torvalds
+ * Copyright (C) 1994, 95, 96, 97, 98, 2000 Ralf Baechle
+ * Copyright (C) 1996 David S. Miller
+ * Kevin D. Kissell, kevink@mips.com and Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 1999 MIPS Technologies, Inc.
+ * Copyright (C) 2000 Ulf Carlsson
+ *
+ * At this time Linux/MIPS64 only supports syscall tracing, even for 32-bit
+ * binaries.
+ */
+#include <linux/compiler.h>
+#include <linux/context_tracking.h>
+#include <linux/elf.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/sched/task_stack.h>
+#include <linux/mm.h>
+#include <linux/errno.h>
+#include <linux/ptrace.h>
+#include <linux/regset.h>
+#include <linux/smp.h>
+#include <linux/security.h>
+#include <linux/stddef.h>
+#include <linux/audit.h>
+#include <linux/seccomp.h>
+#include <linux/ftrace.h>
+
+#include <asm/byteorder.h>
+#include <asm/cpu.h>
+#include <asm/cpu-info.h>
+#include <asm/dsp.h>
+#include <asm/fpu.h>
+#include <asm/mipsregs.h>
+#include <asm/mipsmtregs.h>
+#include <asm/page.h>
+#include <asm/processor.h>
+#include <asm/syscall.h>
+#include <linux/uaccess.h>
+#include <asm/bootinfo.h>
+#include <asm/reg.h>
+
+#define CREATE_TRACE_POINTS
+#include <trace/events/syscalls.h>
+
+/*
+ * Called by kernel/ptrace.c when detaching..
+ *
+ * Make sure single step bits etc are not set.
+ */
+void ptrace_disable(struct task_struct *child)
+{
+	/* Don't load the watchpoint registers for the ex-child. */
+	clear_tsk_thread_flag(child, TIF_LOAD_WATCH);
+}
+
+/*
+ * Read a general register set.	 We always use the 64-bit format, even
+ * for 32-bit kernels and for 32-bit processes on a 64-bit kernel.
+ * Registers are sign extended to fill the available space.
+ */
+int ptrace_getregs(struct task_struct *child, struct user_pt_regs __user *data)
+{
+	struct pt_regs *regs;
+	int i;
+
+	if (!access_ok(data, 38 * 8))
+		return -EIO;
+
+	regs = task_pt_regs(child);
+
+	for (i = 0; i < 32; i++)
+		__put_user((long)regs->regs[i], (__s64 __user *)&data->regs[i]);
+	__put_user((long)regs->lo, (__s64 __user *)&data->lo);
+	__put_user((long)regs->hi, (__s64 __user *)&data->hi);
+	__put_user((long)regs->cp0_epc, (__s64 __user *)&data->cp0_epc);
+	__put_user((long)regs->cp0_badvaddr, (__s64 __user *)&data->cp0_badvaddr);
+	__put_user((long)regs->cp0_status, (__s64 __user *)&data->cp0_status);
+	__put_user((long)regs->cp0_cause, (__s64 __user *)&data->cp0_cause);
+
+	return 0;
+}
+
+/*
+ * Write a general register set.  As for PTRACE_GETREGS, we always use
+ * the 64-bit format.  On a 32-bit kernel only the lower order half
+ * (according to endianness) will be used.
+ */
+int ptrace_setregs(struct task_struct *child, struct user_pt_regs __user *data)
+{
+	struct pt_regs *regs;
+	int i;
+
+	if (!access_ok(data, 38 * 8))
+		return -EIO;
+
+	regs = task_pt_regs(child);
+
+	for (i = 0; i < 32; i++)
+		__get_user(regs->regs[i], (__s64 __user *)&data->regs[i]);
+	__get_user(regs->lo, (__s64 __user *)&data->lo);
+	__get_user(regs->hi, (__s64 __user *)&data->hi);
+	__get_user(regs->cp0_epc, (__s64 __user *)&data->cp0_epc);
+
+	/* badvaddr, status, and cause may not be written.  */
+
+	/* System call number may have been changed */
+	mips_syscall_update_nr(child, regs);
+
+	return 0;
+}
+
+int ptrace_get_watch_regs(struct task_struct *child,
+			  struct pt_watch_regs __user *addr)
+{
+	enum pt_watch_style style;
+	int i;
+
+	if (!cpu_has_watch || boot_cpu_data.watch_reg_use_cnt == 0)
+		return -EIO;
+	if (!access_ok(addr, sizeof(struct pt_watch_regs)))
+		return -EIO;
+
+#ifdef CONFIG_32BIT
+	style = pt_watch_style_mips32;
+#define WATCH_STYLE mips32
+#else
+	style = pt_watch_style_mips64;
+#define WATCH_STYLE mips64
+#endif
+
+	__put_user(style, &addr->style);
+	__put_user(boot_cpu_data.watch_reg_use_cnt,
+		   &addr->WATCH_STYLE.num_valid);
+	for (i = 0; i < boot_cpu_data.watch_reg_use_cnt; i++) {
+		__put_user(child->thread.watch.mips3264.watchlo[i],
+			   &addr->WATCH_STYLE.watchlo[i]);
+		__put_user(child->thread.watch.mips3264.watchhi[i] &
+				(MIPS_WATCHHI_MASK | MIPS_WATCHHI_IRW),
+			   &addr->WATCH_STYLE.watchhi[i]);
+		__put_user(boot_cpu_data.watch_reg_masks[i],
+			   &addr->WATCH_STYLE.watch_masks[i]);
+	}
+	for (; i < 8; i++) {
+		__put_user(0, &addr->WATCH_STYLE.watchlo[i]);
+		__put_user(0, &addr->WATCH_STYLE.watchhi[i]);
+		__put_user(0, &addr->WATCH_STYLE.watch_masks[i]);
+	}
+
+	return 0;
+}
+
+int ptrace_set_watch_regs(struct task_struct *child,
+			  struct pt_watch_regs __user *addr)
+{
+	int i;
+	int watch_active = 0;
+	unsigned long lt[NUM_WATCH_REGS];
+	u16 ht[NUM_WATCH_REGS];
+
+	if (!cpu_has_watch || boot_cpu_data.watch_reg_use_cnt == 0)
+		return -EIO;
+	if (!access_ok(addr, sizeof(struct pt_watch_regs)))
+		return -EIO;
+	/* Check the values. */
+	for (i = 0; i < boot_cpu_data.watch_reg_use_cnt; i++) {
+		__get_user(lt[i], &addr->WATCH_STYLE.watchlo[i]);
+#ifdef CONFIG_32BIT
+		if (lt[i] & __UA_LIMIT)
+			return -EINVAL;
+#else
+		if (test_tsk_thread_flag(child, TIF_32BIT_ADDR)) {
+			if (lt[i] & 0xffffffff80000000UL)
+				return -EINVAL;
+		} else {
+			if (lt[i] & __UA_LIMIT)
+				return -EINVAL;
+		}
+#endif
+		__get_user(ht[i], &addr->WATCH_STYLE.watchhi[i]);
+		if (ht[i] & ~MIPS_WATCHHI_MASK)
+			return -EINVAL;
+	}
+	/* Install them. */
+	for (i = 0; i < boot_cpu_data.watch_reg_use_cnt; i++) {
+		if (lt[i] & MIPS_WATCHLO_IRW)
+			watch_active = 1;
+		child->thread.watch.mips3264.watchlo[i] = lt[i];
+		/* Set the G bit. */
+		child->thread.watch.mips3264.watchhi[i] = ht[i];
+	}
+
+	if (watch_active)
+		set_tsk_thread_flag(child, TIF_LOAD_WATCH);
+	else
+		clear_tsk_thread_flag(child, TIF_LOAD_WATCH);
+
+	return 0;
+}
+
+/* regset get/set implementations */
+
+#if defined(CONFIG_32BIT) || defined(CONFIG_MIPS32_O32)
+
+static int gpr32_get(struct task_struct *target,
+		     const struct user_regset *regset,
+		     struct membuf to)
+{
+	struct pt_regs *regs = task_pt_regs(target);
+	u32 uregs[ELF_NGREG] = {};
+
+	mips_dump_regs32(uregs, regs);
+	return membuf_write(&to, uregs, sizeof(uregs));
+}
+
+static int gpr32_set(struct task_struct *target,
+		     const struct user_regset *regset,
+		     unsigned int pos, unsigned int count,
+		     const void *kbuf, const void __user *ubuf)
+{
+	struct pt_regs *regs = task_pt_regs(target);
+	u32 uregs[ELF_NGREG];
+	unsigned start, num_regs, i;
+	int err;
+
+	start = pos / sizeof(u32);
+	num_regs = count / sizeof(u32);
+
+	if (start + num_regs > ELF_NGREG)
+		return -EIO;
+
+	err = user_regset_copyin(&pos, &count, &kbuf, &ubuf, uregs, 0,
+				 sizeof(uregs));
+	if (err)
+		return err;
+
+	for (i = start; i < num_regs; i++) {
+		/*
+		 * Cast all values to signed here so that if this is a 64-bit
+		 * kernel, the supplied 32-bit values will be sign extended.
+		 */
+		switch (i) {
+		case MIPS32_EF_R1 ... MIPS32_EF_R25:
+			/* k0/k1 are ignored. */
+		case MIPS32_EF_R28 ... MIPS32_EF_R31:
+			regs->regs[i - MIPS32_EF_R0] = (s32)uregs[i];
+			break;
+		case MIPS32_EF_LO:
+			regs->lo = (s32)uregs[i];
+			break;
+		case MIPS32_EF_HI:
+			regs->hi = (s32)uregs[i];
+			break;
+		case MIPS32_EF_CP0_EPC:
+			regs->cp0_epc = (s32)uregs[i];
+			break;
+		}
+	}
+
+	/* System call number may have been changed */
+	mips_syscall_update_nr(target, regs);
+
+	return 0;
+}
+
+#endif /* CONFIG_32BIT || CONFIG_MIPS32_O32 */
+
+#ifdef CONFIG_64BIT
+
+static int gpr64_get(struct task_struct *target,
+		     const struct user_regset *regset,
+		     struct membuf to)
+{
+	struct pt_regs *regs = task_pt_regs(target);
+	u64 uregs[ELF_NGREG] = {};
+
+	mips_dump_regs64(uregs, regs);
+	return membuf_write(&to, uregs, sizeof(uregs));
+}
+
+static int gpr64_set(struct task_struct *target,
+		     const struct user_regset *regset,
+		     unsigned int pos, unsigned int count,
+		     const void *kbuf, const void __user *ubuf)
+{
+	struct pt_regs *regs = task_pt_regs(target);
+	u64 uregs[ELF_NGREG];
+	unsigned start, num_regs, i;
+	int err;
+
+	start = pos / sizeof(u64);
+	num_regs = count / sizeof(u64);
+
+	if (start + num_regs > ELF_NGREG)
+		return -EIO;
+
+	err = user_regset_copyin(&pos, &count, &kbuf, &ubuf, uregs, 0,
+				 sizeof(uregs));
+	if (err)
+		return err;
+
+	for (i = start; i < num_regs; i++) {
+		switch (i) {
+		case MIPS64_EF_R1 ... MIPS64_EF_R25:
+			/* k0/k1 are ignored. */
+		case MIPS64_EF_R28 ... MIPS64_EF_R31:
+			regs->regs[i - MIPS64_EF_R0] = uregs[i];
+			break;
+		case MIPS64_EF_LO:
+			regs->lo = uregs[i];
+			break;
+		case MIPS64_EF_HI:
+			regs->hi = uregs[i];
+			break;
+		case MIPS64_EF_CP0_EPC:
+			regs->cp0_epc = uregs[i];
+			break;
+		}
+	}
+
+	/* System call number may have been changed */
+	mips_syscall_update_nr(target, regs);
+
+	return 0;
+}
+
+#endif /* CONFIG_64BIT */
+
+
+#ifdef CONFIG_MIPS_FP_SUPPORT
+
+/*
+ * Poke at FCSR according to its mask.  Set the Cause bits even
+ * if a corresponding Enable bit is set.  This will be noticed at
+ * the time the thread is switched to and SIGFPE thrown accordingly.
+ */
+static void ptrace_setfcr31(struct task_struct *child, u32 value)
+{
+	u32 fcr31;
+	u32 mask;
+
+	fcr31 = child->thread.fpu.fcr31;
+	mask = boot_cpu_data.fpu_msk31;
+	child->thread.fpu.fcr31 = (value & ~mask) | (fcr31 & mask);
+}
+
+int ptrace_getfpregs(struct task_struct *child, __u32 __user *data)
+{
+	int i;
+
+	if (!access_ok(data, 33 * 8))
+		return -EIO;
+
+	if (tsk_used_math(child)) {
+		union fpureg *fregs = get_fpu_regs(child);
+		for (i = 0; i < 32; i++)
+			__put_user(get_fpr64(&fregs[i], 0),
+				   i + (__u64 __user *)data);
+	} else {
+		for (i = 0; i < 32; i++)
+			__put_user((__u64) -1, i + (__u64 __user *) data);
+	}
+
+	__put_user(child->thread.fpu.fcr31, data + 64);
+	__put_user(boot_cpu_data.fpu_id, data + 65);
+
+	return 0;
+}
+
+int ptrace_setfpregs(struct task_struct *child, __u32 __user *data)
+{
+	union fpureg *fregs;
+	u64 fpr_val;
+	u32 value;
+	int i;
+
+	if (!access_ok(data, 33 * 8))
+		return -EIO;
+
+	init_fp_ctx(child);
+	fregs = get_fpu_regs(child);
+
+	for (i = 0; i < 32; i++) {
+		__get_user(fpr_val, i + (__u64 __user *)data);
+		set_fpr64(&fregs[i], 0, fpr_val);
+	}
+
+	__get_user(value, data + 64);
+	ptrace_setfcr31(child, value);
+
+	/* FIR may not be written.  */
+
+	return 0;
+}
+
+/*
+ * Copy the floating-point context to the supplied NT_PRFPREG buffer,
+ * !CONFIG_CPU_HAS_MSA variant.  FP context's general register slots
+ * correspond 1:1 to buffer slots.  Only general registers are copied.
+ */
+static void fpr_get_fpa(struct task_struct *target,
+		       struct membuf *to)
+{
+	membuf_write(to, &target->thread.fpu,
+			NUM_FPU_REGS * sizeof(elf_fpreg_t));
+}
+
+/*
+ * Copy the floating-point context to the supplied NT_PRFPREG buffer,
+ * CONFIG_CPU_HAS_MSA variant.  Only lower 64 bits of FP context's
+ * general register slots are copied to buffer slots.  Only general
+ * registers are copied.
+ */
+static void fpr_get_msa(struct task_struct *target, struct membuf *to)
+{
+	unsigned int i;
+
+	BUILD_BUG_ON(sizeof(u64) != sizeof(elf_fpreg_t));
+	for (i = 0; i < NUM_FPU_REGS; i++)
+		membuf_store(to, get_fpr64(&target->thread.fpu.fpr[i], 0));
+}
+
+/*
+ * Copy the floating-point context to the supplied NT_PRFPREG buffer.
+ * Choose the appropriate helper for general registers, and then copy
+ * the FCSR and FIR registers separately.
+ */
+static int fpr_get(struct task_struct *target,
+		   const struct user_regset *regset,
+		   struct membuf to)
+{
+	if (sizeof(target->thread.fpu.fpr[0]) == sizeof(elf_fpreg_t))
+		fpr_get_fpa(target, &to);
+	else
+		fpr_get_msa(target, &to);
+
+	membuf_write(&to, &target->thread.fpu.fcr31, sizeof(u32));
+	membuf_write(&to, &boot_cpu_data.fpu_id, sizeof(u32));
+	return 0;
+}
+
+/*
+ * Copy the supplied NT_PRFPREG buffer to the floating-point context,
+ * !CONFIG_CPU_HAS_MSA variant.   Buffer slots correspond 1:1 to FP
+ * context's general register slots.  Only general registers are copied.
+ */
+static int fpr_set_fpa(struct task_struct *target,
+		       unsigned int *pos, unsigned int *count,
+		       const void **kbuf, const void __user **ubuf)
+{
+	return user_regset_copyin(pos, count, kbuf, ubuf,
+				  &target->thread.fpu,
+				  0, NUM_FPU_REGS * sizeof(elf_fpreg_t));
+}
+
+/*
+ * Copy the supplied NT_PRFPREG buffer to the floating-point context,
+ * CONFIG_CPU_HAS_MSA variant.  Buffer slots are copied to lower 64
+ * bits only of FP context's general register slots.  Only general
+ * registers are copied.
+ */
+static int fpr_set_msa(struct task_struct *target,
+		       unsigned int *pos, unsigned int *count,
+		       const void **kbuf, const void __user **ubuf)
+{
+	unsigned int i;
+	u64 fpr_val;
+	int err;
+
+	BUILD_BUG_ON(sizeof(fpr_val) != sizeof(elf_fpreg_t));
+	for (i = 0; i < NUM_FPU_REGS && *count > 0; i++) {
+		err = user_regset_copyin(pos, count, kbuf, ubuf,
+					 &fpr_val, i * sizeof(elf_fpreg_t),
+					 (i + 1) * sizeof(elf_fpreg_t));
+		if (err)
+			return err;
+		set_fpr64(&target->thread.fpu.fpr[i], 0, fpr_val);
+	}
+
+	return 0;
+}
+
+/*
+ * Copy the supplied NT_PRFPREG buffer to the floating-point context.
+ * Choose the appropriate helper for general registers, and then copy
+ * the FCSR register separately.  Ignore the incoming FIR register
+ * contents though, as the register is read-only.
+ *
+ * We optimize for the case where `count % sizeof(elf_fpreg_t) == 0',
+ * which is supposed to have been guaranteed by the kernel before
+ * calling us, e.g. in `ptrace_regset'.  We enforce that requirement,
+ * so that we can safely avoid preinitializing temporaries for
+ * partial register writes.
+ */
+static int fpr_set(struct task_struct *target,
+		   const struct user_regset *regset,
+		   unsigned int pos, unsigned int count,
+		   const void *kbuf, const void __user *ubuf)
+{
+	const int fcr31_pos = NUM_FPU_REGS * sizeof(elf_fpreg_t);
+	const int fir_pos = fcr31_pos + sizeof(u32);
+	u32 fcr31;
+	int err;
+
+	BUG_ON(count % sizeof(elf_fpreg_t));
+
+	if (pos + count > sizeof(elf_fpregset_t))
+		return -EIO;
+
+	init_fp_ctx(target);
+
+	if (sizeof(target->thread.fpu.fpr[0]) == sizeof(elf_fpreg_t))
+		err = fpr_set_fpa(target, &pos, &count, &kbuf, &ubuf);
+	else
+		err = fpr_set_msa(target, &pos, &count, &kbuf, &ubuf);
+	if (err)
+		return err;
+
+	if (count > 0) {
+		err = user_regset_copyin(&pos, &count, &kbuf, &ubuf,
+					 &fcr31,
+					 fcr31_pos, fcr31_pos + sizeof(u32));
+		if (err)
+			return err;
+
+		ptrace_setfcr31(target, fcr31);
+	}
+
+	if (count > 0)
+		err = user_regset_copyin_ignore(&pos, &count, &kbuf, &ubuf,
+						fir_pos,
+						fir_pos + sizeof(u32));
+
+	return err;
+}
+
+/* Copy the FP mode setting to the supplied NT_MIPS_FP_MODE buffer.  */
+static int fp_mode_get(struct task_struct *target,
+		       const struct user_regset *regset,
+		       struct membuf to)
+{
+	return membuf_store(&to, (int)mips_get_process_fp_mode(target));
+}
+
+/*
+ * Copy the supplied NT_MIPS_FP_MODE buffer to the FP mode setting.
+ *
+ * We optimize for the case where `count % sizeof(int) == 0', which
+ * is supposed to have been guaranteed by the kernel before calling
+ * us, e.g. in `ptrace_regset'.  We enforce that requirement, so
+ * that we can safely avoid preinitializing temporaries for partial
+ * mode writes.
+ */
+static int fp_mode_set(struct task_struct *target,
+		       const struct user_regset *regset,
+		       unsigned int pos, unsigned int count,
+		       const void *kbuf, const void __user *ubuf)
+{
+	int fp_mode;
+	int err;
+
+	BUG_ON(count % sizeof(int));
+
+	if (pos + count > sizeof(fp_mode))
+		return -EIO;
+
+	err = user_regset_copyin(&pos, &count, &kbuf, &ubuf, &fp_mode, 0,
+				 sizeof(fp_mode));
+	if (err)
+		return err;
+
+	if (count > 0)
+		err = mips_set_process_fp_mode(target, fp_mode);
+
+	return err;
+}
+
+#endif /* CONFIG_MIPS_FP_SUPPORT */
+
+#ifdef CONFIG_CPU_HAS_MSA
+
+struct msa_control_regs {
+	unsigned int fir;
+	unsigned int fcsr;
+	unsigned int msair;
+	unsigned int msacsr;
+};
+
+static void copy_pad_fprs(struct task_struct *target,
+			 const struct user_regset *regset,
+			 struct membuf *to,
+			 unsigned int live_sz)
+{
+	int i, j;
+	unsigned long long fill = ~0ull;
+	unsigned int cp_sz, pad_sz;
+
+	cp_sz = min(regset->size, live_sz);
+	pad_sz = regset->size - cp_sz;
+	WARN_ON(pad_sz % sizeof(fill));
+
+	for (i = 0; i < NUM_FPU_REGS; i++) {
+		membuf_write(to, &target->thread.fpu.fpr[i], cp_sz);
+		for (j = 0; j < (pad_sz / sizeof(fill)); j++)
+			membuf_store(to, fill);
+	}
+}
+
+static int msa_get(struct task_struct *target,
+		   const struct user_regset *regset,
+		   struct membuf to)
+{
+	const unsigned int wr_size = NUM_FPU_REGS * regset->size;
+	const struct msa_control_regs ctrl_regs = {
+		.fir = boot_cpu_data.fpu_id,
+		.fcsr = target->thread.fpu.fcr31,
+		.msair = boot_cpu_data.msa_id,
+		.msacsr = target->thread.fpu.msacsr,
+	};
+
+	if (!tsk_used_math(target)) {
+		/* The task hasn't used FP or MSA, fill with 0xff */
+		copy_pad_fprs(target, regset, &to, 0);
+	} else if (!test_tsk_thread_flag(target, TIF_MSA_CTX_LIVE)) {
+		/* Copy scalar FP context, fill the rest with 0xff */
+		copy_pad_fprs(target, regset, &to, 8);
+	} else if (sizeof(target->thread.fpu.fpr[0]) == regset->size) {
+		/* Trivially copy the vector registers */
+		membuf_write(&to, &target->thread.fpu.fpr, wr_size);
+	} else {
+		/* Copy as much context as possible, fill the rest with 0xff */
+		copy_pad_fprs(target, regset, &to,
+				sizeof(target->thread.fpu.fpr[0]));
+	}
+
+	return membuf_write(&to, &ctrl_regs, sizeof(ctrl_regs));
+}
+
+static int msa_set(struct task_struct *target,
+		   const struct user_regset *regset,
+		   unsigned int pos, unsigned int count,
+		   const void *kbuf, const void __user *ubuf)
+{
+	const unsigned int wr_size = NUM_FPU_REGS * regset->size;
+	struct msa_control_regs ctrl_regs;
+	unsigned int cp_sz;
+	int i, err, start;
+
+	init_fp_ctx(target);
+
+	if (sizeof(target->thread.fpu.fpr[0]) == regset->size) {
+		/* Trivially copy the vector registers */
+		err = user_regset_copyin(&pos, &count, &kbuf, &ubuf,
+					 &target->thread.fpu.fpr,
+					 0, wr_size);
+	} else {
+		/* Copy as much context as possible */
+		cp_sz = min_t(unsigned int, regset->size,
+			      sizeof(target->thread.fpu.fpr[0]));
+
+		i = start = err = 0;
+		for (; i < NUM_FPU_REGS; i++, start += regset->size) {
+			err |= user_regset_copyin(&pos, &count, &kbuf, &ubuf,
+						  &target->thread.fpu.fpr[i],
+						  start, start + cp_sz);
+		}
+	}
+
+	if (!err)
+		err = user_regset_copyin(&pos, &count, &kbuf, &ubuf, &ctrl_regs,
+					 wr_size, wr_size + sizeof(ctrl_regs));
+	if (!err) {
+		target->thread.fpu.fcr31 = ctrl_regs.fcsr & ~FPU_CSR_ALL_X;
+		target->thread.fpu.msacsr = ctrl_regs.msacsr & ~MSA_CSR_CAUSEF;
+	}
+
+	return err;
+}
+
+#endif /* CONFIG_CPU_HAS_MSA */
+
+#if defined(CONFIG_32BIT) || defined(CONFIG_MIPS32_O32)
+
+/*
+ * Copy the DSP context to the supplied 32-bit NT_MIPS_DSP buffer.
+ */
+static int dsp32_get(struct task_struct *target,
+		     const struct user_regset *regset,
+		     struct membuf to)
+{
+	u32 dspregs[NUM_DSP_REGS + 1];
+	unsigned int i;
+
+	BUG_ON(to.left % sizeof(u32));
+
+	if (!cpu_has_dsp)
+		return -EIO;
+
+	for (i = 0; i < NUM_DSP_REGS; i++)
+		dspregs[i] = target->thread.dsp.dspr[i];
+	dspregs[NUM_DSP_REGS] = target->thread.dsp.dspcontrol;
+	return membuf_write(&to, dspregs, sizeof(dspregs));
+}
+
+/*
+ * Copy the supplied 32-bit NT_MIPS_DSP buffer to the DSP context.
+ */
+static int dsp32_set(struct task_struct *target,
+		     const struct user_regset *regset,
+		     unsigned int pos, unsigned int count,
+		     const void *kbuf, const void __user *ubuf)
+{
+	unsigned int start, num_regs, i;
+	u32 dspregs[NUM_DSP_REGS + 1];
+	int err;
+
+	BUG_ON(count % sizeof(u32));
+
+	if (!cpu_has_dsp)
+		return -EIO;
+
+	start = pos / sizeof(u32);
+	num_regs = count / sizeof(u32);
+
+	if (start + num_regs > NUM_DSP_REGS + 1)
+		return -EIO;
+
+	err = user_regset_copyin(&pos, &count, &kbuf, &ubuf, dspregs, 0,
+				 sizeof(dspregs));
+	if (err)
+		return err;
+
+	for (i = start; i < num_regs; i++)
+		switch (i) {
+		case 0 ... NUM_DSP_REGS - 1:
+			target->thread.dsp.dspr[i] = (s32)dspregs[i];
+			break;
+		case NUM_DSP_REGS:
+			target->thread.dsp.dspcontrol = (s32)dspregs[i];
+			break;
+		}
+
+	return 0;
+}
+
+#endif /* CONFIG_32BIT || CONFIG_MIPS32_O32 */
+
+#ifdef CONFIG_64BIT
+
+/*
+ * Copy the DSP context to the supplied 64-bit NT_MIPS_DSP buffer.
+ */
+static int dsp64_get(struct task_struct *target,
+		     const struct user_regset *regset,
+		     struct membuf to)
+{
+	u64 dspregs[NUM_DSP_REGS + 1];
+	unsigned int i;
+
+	BUG_ON(to.left % sizeof(u64));
+
+	if (!cpu_has_dsp)
+		return -EIO;
+
+	for (i = 0; i < NUM_DSP_REGS; i++)
+		dspregs[i] = target->thread.dsp.dspr[i];
+	dspregs[NUM_DSP_REGS] = target->thread.dsp.dspcontrol;
+	return membuf_write(&to, dspregs, sizeof(dspregs));
+}
+
+/*
+ * Copy the supplied 64-bit NT_MIPS_DSP buffer to the DSP context.
+ */
+static int dsp64_set(struct task_struct *target,
+		     const struct user_regset *regset,
+		     unsigned int pos, unsigned int count,
+		     const void *kbuf, const void __user *ubuf)
+{
+	unsigned int start, num_regs, i;
+	u64 dspregs[NUM_DSP_REGS + 1];
+	int err;
+
+	BUG_ON(count % sizeof(u64));
+
+	if (!cpu_has_dsp)
+		return -EIO;
+
+	start = pos / sizeof(u64);
+	num_regs = count / sizeof(u64);
+
+	if (start + num_regs > NUM_DSP_REGS + 1)
+		return -EIO;
+
+	err = user_regset_copyin(&pos, &count, &kbuf, &ubuf, dspregs, 0,
+				 sizeof(dspregs));
+	if (err)
+		return err;
+
+	for (i = start; i < num_regs; i++)
+		switch (i) {
+		case 0 ... NUM_DSP_REGS - 1:
+			target->thread.dsp.dspr[i] = dspregs[i];
+			break;
+		case NUM_DSP_REGS:
+			target->thread.dsp.dspcontrol = dspregs[i];
+			break;
+		}
+
+	return 0;
+}
+
+#endif /* CONFIG_64BIT */
+
+/*
+ * Determine whether the DSP context is present.
+ */
+static int dsp_active(struct task_struct *target,
+		      const struct user_regset *regset)
+{
+	return cpu_has_dsp ? NUM_DSP_REGS + 1 : -ENODEV;
+}
+
+enum mips_regset {
+	REGSET_GPR,
+	REGSET_DSP,
+#ifdef CONFIG_MIPS_FP_SUPPORT
+	REGSET_FPR,
+	REGSET_FP_MODE,
+#endif
+#ifdef CONFIG_CPU_HAS_MSA
+	REGSET_MSA,
+#endif
+};
+
+struct pt_regs_offset {
+	const char *name;
+	int offset;
+};
+
+#define REG_OFFSET_NAME(reg, r) {					\
+	.name = #reg,							\
+	.offset = offsetof(struct pt_regs, r)				\
+}
+
+#define REG_OFFSET_END {						\
+	.name = NULL,							\
+	.offset = 0							\
+}
+
+static const struct pt_regs_offset regoffset_table[] = {
+	REG_OFFSET_NAME(r0, regs[0]),
+	REG_OFFSET_NAME(r1, regs[1]),
+	REG_OFFSET_NAME(r2, regs[2]),
+	REG_OFFSET_NAME(r3, regs[3]),
+	REG_OFFSET_NAME(r4, regs[4]),
+	REG_OFFSET_NAME(r5, regs[5]),
+	REG_OFFSET_NAME(r6, regs[6]),
+	REG_OFFSET_NAME(r7, regs[7]),
+	REG_OFFSET_NAME(r8, regs[8]),
+	REG_OFFSET_NAME(r9, regs[9]),
+	REG_OFFSET_NAME(r10, regs[10]),
+	REG_OFFSET_NAME(r11, regs[11]),
+	REG_OFFSET_NAME(r12, regs[12]),
+	REG_OFFSET_NAME(r13, regs[13]),
+	REG_OFFSET_NAME(r14, regs[14]),
+	REG_OFFSET_NAME(r15, regs[15]),
+	REG_OFFSET_NAME(r16, regs[16]),
+	REG_OFFSET_NAME(r17, regs[17]),
+	REG_OFFSET_NAME(r18, regs[18]),
+	REG_OFFSET_NAME(r19, regs[19]),
+	REG_OFFSET_NAME(r20, regs[20]),
+	REG_OFFSET_NAME(r21, regs[21]),
+	REG_OFFSET_NAME(r22, regs[22]),
+	REG_OFFSET_NAME(r23, regs[23]),
+	REG_OFFSET_NAME(r24, regs[24]),
+	REG_OFFSET_NAME(r25, regs[25]),
+	REG_OFFSET_NAME(r26, regs[26]),
+	REG_OFFSET_NAME(r27, regs[27]),
+	REG_OFFSET_NAME(r28, regs[28]),
+	REG_OFFSET_NAME(r29, regs[29]),
+	REG_OFFSET_NAME(r30, regs[30]),
+	REG_OFFSET_NAME(r31, regs[31]),
+	REG_OFFSET_NAME(c0_status, cp0_status),
+	REG_OFFSET_NAME(hi, hi),
+	REG_OFFSET_NAME(lo, lo),
+#ifdef CONFIG_CPU_HAS_SMARTMIPS
+	REG_OFFSET_NAME(acx, acx),
+#endif
+	REG_OFFSET_NAME(c0_badvaddr, cp0_badvaddr),
+	REG_OFFSET_NAME(c0_cause, cp0_cause),
+	REG_OFFSET_NAME(c0_epc, cp0_epc),
+#ifdef CONFIG_CPU_CAVIUM_OCTEON
+	REG_OFFSET_NAME(mpl0, mpl[0]),
+	REG_OFFSET_NAME(mpl1, mpl[1]),
+	REG_OFFSET_NAME(mpl2, mpl[2]),
+	REG_OFFSET_NAME(mtp0, mtp[0]),
+	REG_OFFSET_NAME(mtp1, mtp[1]),
+	REG_OFFSET_NAME(mtp2, mtp[2]),
+#endif
+	REG_OFFSET_END,
+};
+
+/**
+ * regs_query_register_offset() - query register offset from its name
+ * @name:       the name of a register
+ *
+ * regs_query_register_offset() returns the offset of a register in struct
+ * pt_regs from its name. If the name is invalid, this returns -EINVAL;
+ */
+int regs_query_register_offset(const char *name)
+{
+        const struct pt_regs_offset *roff;
+        for (roff = regoffset_table; roff->name != NULL; roff++)
+                if (!strcmp(roff->name, name))
+                        return roff->offset;
+        return -EINVAL;
+}
+
+#if defined(CONFIG_32BIT) || defined(CONFIG_MIPS32_O32)
+
+static const struct user_regset mips_regsets[] = {
+	[REGSET_GPR] = {
+		.core_note_type	= NT_PRSTATUS,
+		.n		= ELF_NGREG,
+		.size		= sizeof(unsigned int),
+		.align		= sizeof(unsigned int),
+		.regset_get		= gpr32_get,
+		.set		= gpr32_set,
+	},
+	[REGSET_DSP] = {
+		.core_note_type	= NT_MIPS_DSP,
+		.n		= NUM_DSP_REGS + 1,
+		.size		= sizeof(u32),
+		.align		= sizeof(u32),
+		.regset_get		= dsp32_get,
+		.set		= dsp32_set,
+		.active		= dsp_active,
+	},
+#ifdef CONFIG_MIPS_FP_SUPPORT
+	[REGSET_FPR] = {
+		.core_note_type	= NT_PRFPREG,
+		.n		= ELF_NFPREG,
+		.size		= sizeof(elf_fpreg_t),
+		.align		= sizeof(elf_fpreg_t),
+		.regset_get		= fpr_get,
+		.set		= fpr_set,
+	},
+	[REGSET_FP_MODE] = {
+		.core_note_type	= NT_MIPS_FP_MODE,
+		.n		= 1,
+		.size		= sizeof(int),
+		.align		= sizeof(int),
+		.regset_get		= fp_mode_get,
+		.set		= fp_mode_set,
+	},
+#endif
+#ifdef CONFIG_CPU_HAS_MSA
+	[REGSET_MSA] = {
+		.core_note_type	= NT_MIPS_MSA,
+		.n		= NUM_FPU_REGS + 1,
+		.size		= 16,
+		.align		= 16,
+		.regset_get		= msa_get,
+		.set		= msa_set,
+	},
+#endif
+};
+
+static const struct user_regset_view user_mips_view = {
+	.name		= "mips",
+	.e_machine	= ELF_ARCH,
+	.ei_osabi	= ELF_OSABI,
+	.regsets	= mips_regsets,
+	.n		= ARRAY_SIZE(mips_regsets),
+};
+
+#endif /* CONFIG_32BIT || CONFIG_MIPS32_O32 */
+
+#ifdef CONFIG_64BIT
+
+static const struct user_regset mips64_regsets[] = {
+	[REGSET_GPR] = {
+		.core_note_type	= NT_PRSTATUS,
+		.n		= ELF_NGREG,
+		.size		= sizeof(unsigned long),
+		.align		= sizeof(unsigned long),
+		.regset_get		= gpr64_get,
+		.set		= gpr64_set,
+	},
+	[REGSET_DSP] = {
+		.core_note_type	= NT_MIPS_DSP,
+		.n		= NUM_DSP_REGS + 1,
+		.size		= sizeof(u64),
+		.align		= sizeof(u64),
+		.regset_get		= dsp64_get,
+		.set		= dsp64_set,
+		.active		= dsp_active,
+	},
+#ifdef CONFIG_MIPS_FP_SUPPORT
+	[REGSET_FP_MODE] = {
+		.core_note_type	= NT_MIPS_FP_MODE,
+		.n		= 1,
+		.size		= sizeof(int),
+		.align		= sizeof(int),
+		.regset_get		= fp_mode_get,
+		.set		= fp_mode_set,
+	},
+	[REGSET_FPR] = {
+		.core_note_type	= NT_PRFPREG,
+		.n		= ELF_NFPREG,
+		.size		= sizeof(elf_fpreg_t),
+		.align		= sizeof(elf_fpreg_t),
+		.regset_get		= fpr_get,
+		.set		= fpr_set,
+	},
+#endif
+#ifdef CONFIG_CPU_HAS_MSA
+	[REGSET_MSA] = {
+		.core_note_type	= NT_MIPS_MSA,
+		.n		= NUM_FPU_REGS + 1,
+		.size		= 16,
+		.align		= 16,
+		.regset_get		= msa_get,
+		.set		= msa_set,
+	},
+#endif
+};
+
+static const struct user_regset_view user_mips64_view = {
+	.name		= "mips64",
+	.e_machine	= ELF_ARCH,
+	.ei_osabi	= ELF_OSABI,
+	.regsets	= mips64_regsets,
+	.n		= ARRAY_SIZE(mips64_regsets),
+};
+
+#ifdef CONFIG_MIPS32_N32
+
+static const struct user_regset_view user_mipsn32_view = {
+	.name		= "mipsn32",
+	.e_flags	= EF_MIPS_ABI2,
+	.e_machine	= ELF_ARCH,
+	.ei_osabi	= ELF_OSABI,
+	.regsets	= mips64_regsets,
+	.n		= ARRAY_SIZE(mips64_regsets),
+};
+
+#endif /* CONFIG_MIPS32_N32 */
+
+#endif /* CONFIG_64BIT */
+
+const struct user_regset_view *task_user_regset_view(struct task_struct *task)
+{
+#ifdef CONFIG_32BIT
+	return &user_mips_view;
+#else
+#ifdef CONFIG_MIPS32_O32
+	if (test_tsk_thread_flag(task, TIF_32BIT_REGS))
+		return &user_mips_view;
+#endif
+#ifdef CONFIG_MIPS32_N32
+	if (test_tsk_thread_flag(task, TIF_32BIT_ADDR))
+		return &user_mipsn32_view;
+#endif
+	return &user_mips64_view;
+#endif
+}
+
+long arch_ptrace(struct task_struct *child, long request,
+		 unsigned long addr, unsigned long data)
+{
+	int ret;
+	void __user *addrp = (void __user *) addr;
+	void __user *datavp = (void __user *) data;
+	unsigned long __user *datalp = (void __user *) data;
+
+	switch (request) {
+	/* when I and D space are separate, these will need to be fixed. */
+	case PTRACE_PEEKTEXT: /* read word at location addr. */
+	case PTRACE_PEEKDATA:
+		ret = generic_ptrace_peekdata(child, addr, data);
+		break;
+
+	/* Read the word at location addr in the USER area. */
+	case PTRACE_PEEKUSR: {
+		struct pt_regs *regs;
+		unsigned long tmp = 0;
+
+		regs = task_pt_regs(child);
+		ret = 0;  /* Default return value. */
+
+		switch (addr) {
+		case 0 ... 31:
+			tmp = regs->regs[addr];
+			break;
+#ifdef CONFIG_MIPS_FP_SUPPORT
+		case FPR_BASE ... FPR_BASE + 31: {
+			union fpureg *fregs;
+
+			if (!tsk_used_math(child)) {
+				/* FP not yet used */
+				tmp = -1;
+				break;
+			}
+			fregs = get_fpu_regs(child);
+
+#ifdef CONFIG_32BIT
+			if (test_tsk_thread_flag(child, TIF_32BIT_FPREGS)) {
+				/*
+				 * The odd registers are actually the high
+				 * order bits of the values stored in the even
+				 * registers.
+				 */
+				tmp = get_fpr32(&fregs[(addr & ~1) - FPR_BASE],
+						addr & 1);
+				break;
+			}
+#endif
+			tmp = get_fpr64(&fregs[addr - FPR_BASE], 0);
+			break;
+		}
+		case FPC_CSR:
+			tmp = child->thread.fpu.fcr31;
+			break;
+		case FPC_EIR:
+			/* implementation / version register */
+			tmp = boot_cpu_data.fpu_id;
+			break;
+#endif
+		case PC:
+			tmp = regs->cp0_epc;
+			break;
+		case CAUSE:
+			tmp = regs->cp0_cause;
+			break;
+		case BADVADDR:
+			tmp = regs->cp0_badvaddr;
+			break;
+		case MMHI:
+			tmp = regs->hi;
+			break;
+		case MMLO:
+			tmp = regs->lo;
+			break;
+#ifdef CONFIG_CPU_HAS_SMARTMIPS
+		case ACX:
+			tmp = regs->acx;
+			break;
+#endif
+		case DSP_BASE ... DSP_BASE + 5: {
+			dspreg_t *dregs;
+
+			if (!cpu_has_dsp) {
+				tmp = 0;
+				ret = -EIO;
+				goto out;
+			}
+			dregs = __get_dsp_regs(child);
+			tmp = dregs[addr - DSP_BASE];
+			break;
+		}
+		case DSP_CONTROL:
+			if (!cpu_has_dsp) {
+				tmp = 0;
+				ret = -EIO;
+				goto out;
+			}
+			tmp = child->thread.dsp.dspcontrol;
+			break;
+		default:
+			tmp = 0;
+			ret = -EIO;
+			goto out;
+		}
+		ret = put_user(tmp, datalp);
+		break;
+	}
+
+	/* when I and D space are separate, this will have to be fixed. */
+	case PTRACE_POKETEXT: /* write the word at location addr. */
+	case PTRACE_POKEDATA:
+		ret = generic_ptrace_pokedata(child, addr, data);
+		break;
+
+	case PTRACE_POKEUSR: {
+		struct pt_regs *regs;
+		ret = 0;
+		regs = task_pt_regs(child);
+
+		switch (addr) {
+		case 0 ... 31:
+			regs->regs[addr] = data;
+			/* System call number may have been changed */
+			if (addr == 2)
+				mips_syscall_update_nr(child, regs);
+			else if (addr == 4 &&
+				 mips_syscall_is_indirect(child, regs))
+				mips_syscall_update_nr(child, regs);
+			break;
+#ifdef CONFIG_MIPS_FP_SUPPORT
+		case FPR_BASE ... FPR_BASE + 31: {
+			union fpureg *fregs = get_fpu_regs(child);
+
+			init_fp_ctx(child);
+#ifdef CONFIG_32BIT
+			if (test_tsk_thread_flag(child, TIF_32BIT_FPREGS)) {
+				/*
+				 * The odd registers are actually the high
+				 * order bits of the values stored in the even
+				 * registers.
+				 */
+				set_fpr32(&fregs[(addr & ~1) - FPR_BASE],
+					  addr & 1, data);
+				break;
+			}
+#endif
+			set_fpr64(&fregs[addr - FPR_BASE], 0, data);
+			break;
+		}
+		case FPC_CSR:
+			init_fp_ctx(child);
+			ptrace_setfcr31(child, data);
+			break;
+#endif
+		case PC:
+			regs->cp0_epc = data;
+			break;
+		case MMHI:
+			regs->hi = data;
+			break;
+		case MMLO:
+			regs->lo = data;
+			break;
+#ifdef CONFIG_CPU_HAS_SMARTMIPS
+		case ACX:
+			regs->acx = data;
+			break;
+#endif
+		case DSP_BASE ... DSP_BASE + 5: {
+			dspreg_t *dregs;
+
+			if (!cpu_has_dsp) {
+				ret = -EIO;
+				break;
+			}
+
+			dregs = __get_dsp_regs(child);
+			dregs[addr - DSP_BASE] = data;
+			break;
+		}
+		case DSP_CONTROL:
+			if (!cpu_has_dsp) {
+				ret = -EIO;
+				break;
+			}
+			child->thread.dsp.dspcontrol = data;
+			break;
+		default:
+			/* The rest are not allowed. */
+			ret = -EIO;
+			break;
+		}
+		break;
+		}
+
+	case PTRACE_GETREGS:
+		ret = ptrace_getregs(child, datavp);
+		break;
+
+	case PTRACE_SETREGS:
+		ret = ptrace_setregs(child, datavp);
+		break;
+
+#ifdef CONFIG_MIPS_FP_SUPPORT
+	case PTRACE_GETFPREGS:
+		ret = ptrace_getfpregs(child, datavp);
+		break;
+
+	case PTRACE_SETFPREGS:
+		ret = ptrace_setfpregs(child, datavp);
+		break;
+#endif
+	case PTRACE_GET_THREAD_AREA:
+		ret = put_user(task_thread_info(child)->tp_value, datalp);
+		break;
+
+	case PTRACE_GET_WATCH_REGS:
+		ret = ptrace_get_watch_regs(child, addrp);
+		break;
+
+	case PTRACE_SET_WATCH_REGS:
+		ret = ptrace_set_watch_regs(child, addrp);
+		break;
+
+	default:
+		ret = ptrace_request(child, request, addr, data);
+		break;
+	}
+ out:
+	return ret;
+}
+
+/*
+ * Notification of system call entry/exit
+ * - triggered by current->work.syscall_trace
+ */
+asmlinkage long syscall_trace_enter(struct pt_regs *regs, long syscall)
+{
+	user_exit();
+
+	current_thread_info()->syscall = syscall;
+
+	if (test_thread_flag(TIF_SYSCALL_TRACE)) {
+		if (ptrace_report_syscall_entry(regs))
+			return -1;
+		syscall = current_thread_info()->syscall;
+	}
+
+#ifdef CONFIG_SECCOMP
+	if (unlikely(test_thread_flag(TIF_SECCOMP))) {
+		int ret, i;
+		struct seccomp_data sd;
+		unsigned long args[6];
+
+		sd.nr = syscall;
+		sd.arch = syscall_get_arch(current);
+		syscall_get_arguments(current, regs, args);
+		for (i = 0; i < 6; i++)
+			sd.args[i] = args[i];
+		sd.instruction_pointer = KSTK_EIP(current);
+
+		ret = __secure_computing(&sd);
+		if (ret == -1)
+			return ret;
+		syscall = current_thread_info()->syscall;
+	}
+#endif
+
+	if (unlikely(test_thread_flag(TIF_SYSCALL_TRACEPOINT)))
+		trace_sys_enter(regs, regs->regs[2]);
+
+	audit_syscall_entry(syscall, regs->regs[4], regs->regs[5],
+			    regs->regs[6], regs->regs[7]);
+
+	/*
+	 * Negative syscall numbers are mistaken for rejected syscalls, but
+	 * won't have had the return value set appropriately, so we do so now.
+	 */
+	if (syscall < 0)
+		syscall_set_return_value(current, regs, -ENOSYS, 0);
+	return syscall;
+}
+
+/*
+ * Notification of system call entry/exit
+ * - triggered by current->work.syscall_trace
+ */
+asmlinkage void syscall_trace_leave(struct pt_regs *regs)
+{
+        /*
+	 * We may come here right after calling schedule_user()
+	 * or do_notify_resume(), in which case we can be in RCU
+	 * user mode.
+	 */
+	user_exit();
+
+	audit_syscall_exit(regs);
+
+	if (unlikely(test_thread_flag(TIF_SYSCALL_TRACEPOINT)))
+		trace_sys_exit(regs, regs_return_value(regs));
+
+	if (test_thread_flag(TIF_SYSCALL_TRACE))
+		ptrace_report_syscall_exit(regs, 0);
+
+	user_enter();
+}
diff --git a/arch/mips/kernel/ptrace32.c b/arch/mips/kernel/ptrace32.c
new file mode 100644
index 000000000..afcf27a87
--- /dev/null
+++ b/arch/mips/kernel/ptrace32.c
@@ -0,0 +1,317 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1992 Ross Biro
+ * Copyright (C) Linus Torvalds
+ * Copyright (C) 1994, 95, 96, 97, 98, 2000 Ralf Baechle
+ * Copyright (C) 1996 David S. Miller
+ * Kevin D. Kissell, kevink@mips.com and Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 1999 MIPS Technologies, Inc.
+ * Copyright (C) 2000 Ulf Carlsson
+ *
+ * At this time Linux/MIPS64 only supports syscall tracing, even for 32-bit
+ * binaries.
+ */
+#include <linux/compiler.h>
+#include <linux/compat.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/sched/task_stack.h>
+#include <linux/mm.h>
+#include <linux/errno.h>
+#include <linux/ptrace.h>
+#include <linux/smp.h>
+#include <linux/security.h>
+
+#include <asm/cpu.h>
+#include <asm/dsp.h>
+#include <asm/fpu.h>
+#include <asm/mipsregs.h>
+#include <asm/mipsmtregs.h>
+#include <asm/page.h>
+#include <asm/reg.h>
+#include <asm/syscall.h>
+#include <linux/uaccess.h>
+#include <asm/bootinfo.h>
+
+/*
+ * Tracing a 32-bit process with a 64-bit strace and vice versa will not
+ * work.  I don't know how to fix this.
+ */
+long compat_arch_ptrace(struct task_struct *child, compat_long_t request,
+			compat_ulong_t caddr, compat_ulong_t cdata)
+{
+	int addr = caddr;
+	int data = cdata;
+	int ret;
+
+	switch (request) {
+
+	/*
+	 * Read 4 bytes of the other process' storage
+	 *  data is a pointer specifying where the user wants the
+	 *	4 bytes copied into
+	 *  addr is a pointer in the user's storage that contains an 8 byte
+	 *	address in the other process of the 4 bytes that is to be read
+	 * (this is run in a 32-bit process looking at a 64-bit process)
+	 * when I and D space are separate, these will need to be fixed.
+	 */
+	case PTRACE_PEEKTEXT_3264:
+	case PTRACE_PEEKDATA_3264: {
+		u32 tmp;
+		int copied;
+		u32 __user * addrOthers;
+
+		ret = -EIO;
+
+		/* Get the addr in the other process that we want to read */
+		if (get_user(addrOthers, (u32 __user * __user *) (unsigned long) addr) != 0)
+			break;
+
+		copied = ptrace_access_vm(child, (u64)addrOthers, &tmp,
+				sizeof(tmp), FOLL_FORCE);
+		if (copied != sizeof(tmp))
+			break;
+		ret = put_user(tmp, (u32 __user *) (unsigned long) data);
+		break;
+	}
+
+	/* Read the word at location addr in the USER area. */
+	case PTRACE_PEEKUSR: {
+		struct pt_regs *regs;
+		unsigned int tmp;
+
+		regs = task_pt_regs(child);
+		ret = 0;  /* Default return value. */
+
+		switch (addr) {
+		case 0 ... 31:
+			tmp = regs->regs[addr];
+			break;
+#ifdef CONFIG_MIPS_FP_SUPPORT
+		case FPR_BASE ... FPR_BASE + 31: {
+			union fpureg *fregs;
+
+			if (!tsk_used_math(child)) {
+				/* FP not yet used */
+				tmp = -1;
+				break;
+			}
+			fregs = get_fpu_regs(child);
+			if (test_tsk_thread_flag(child, TIF_32BIT_FPREGS)) {
+				/*
+				 * The odd registers are actually the high
+				 * order bits of the values stored in the even
+				 * registers.
+				 */
+				tmp = get_fpr32(&fregs[(addr & ~1) - FPR_BASE],
+						addr & 1);
+				break;
+			}
+			tmp = get_fpr64(&fregs[addr - FPR_BASE], 0);
+			break;
+		}
+		case FPC_CSR:
+			tmp = child->thread.fpu.fcr31;
+			break;
+		case FPC_EIR:
+			/* implementation / version register */
+			tmp = boot_cpu_data.fpu_id;
+			break;
+#endif /* CONFIG_MIPS_FP_SUPPORT */
+		case PC:
+			tmp = regs->cp0_epc;
+			break;
+		case CAUSE:
+			tmp = regs->cp0_cause;
+			break;
+		case BADVADDR:
+			tmp = regs->cp0_badvaddr;
+			break;
+		case MMHI:
+			tmp = regs->hi;
+			break;
+		case MMLO:
+			tmp = regs->lo;
+			break;
+		case DSP_BASE ... DSP_BASE + 5: {
+			dspreg_t *dregs;
+
+			if (!cpu_has_dsp) {
+				tmp = 0;
+				ret = -EIO;
+				goto out;
+			}
+			dregs = __get_dsp_regs(child);
+			tmp = dregs[addr - DSP_BASE];
+			break;
+		}
+		case DSP_CONTROL:
+			if (!cpu_has_dsp) {
+				tmp = 0;
+				ret = -EIO;
+				goto out;
+			}
+			tmp = child->thread.dsp.dspcontrol;
+			break;
+		default:
+			tmp = 0;
+			ret = -EIO;
+			goto out;
+		}
+		ret = put_user(tmp, (unsigned __user *) (unsigned long) data);
+		break;
+	}
+
+	/*
+	 * Write 4 bytes into the other process' storage
+	 *  data is the 4 bytes that the user wants written
+	 *  addr is a pointer in the user's storage that contains an
+	 *	8 byte address in the other process where the 4 bytes
+	 *	that is to be written
+	 * (this is run in a 32-bit process looking at a 64-bit process)
+	 * when I and D space are separate, these will need to be fixed.
+	 */
+	case PTRACE_POKETEXT_3264:
+	case PTRACE_POKEDATA_3264: {
+		u32 __user * addrOthers;
+
+		/* Get the addr in the other process that we want to write into */
+		ret = -EIO;
+		if (get_user(addrOthers, (u32 __user * __user *) (unsigned long) addr) != 0)
+			break;
+		ret = 0;
+		if (ptrace_access_vm(child, (u64)addrOthers, &data,
+					sizeof(data),
+					FOLL_FORCE | FOLL_WRITE) == sizeof(data))
+			break;
+		ret = -EIO;
+		break;
+	}
+
+	case PTRACE_POKEUSR: {
+		struct pt_regs *regs;
+		ret = 0;
+		regs = task_pt_regs(child);
+
+		switch (addr) {
+		case 0 ... 31:
+			regs->regs[addr] = data;
+			/* System call number may have been changed */
+			if (addr == 2)
+				mips_syscall_update_nr(child, regs);
+			else if (addr == 4 &&
+				 mips_syscall_is_indirect(child, regs))
+				mips_syscall_update_nr(child, regs);
+			break;
+#ifdef CONFIG_MIPS_FP_SUPPORT
+		case FPR_BASE ... FPR_BASE + 31: {
+			union fpureg *fregs = get_fpu_regs(child);
+
+			if (!tsk_used_math(child)) {
+				/* FP not yet used  */
+				memset(&child->thread.fpu, ~0,
+				       sizeof(child->thread.fpu));
+				child->thread.fpu.fcr31 = 0;
+			}
+			if (test_tsk_thread_flag(child, TIF_32BIT_FPREGS)) {
+				/*
+				 * The odd registers are actually the high
+				 * order bits of the values stored in the even
+				 * registers.
+				 */
+				set_fpr32(&fregs[(addr & ~1) - FPR_BASE],
+					  addr & 1, data);
+				break;
+			}
+			set_fpr64(&fregs[addr - FPR_BASE], 0, data);
+			break;
+		}
+		case FPC_CSR:
+			child->thread.fpu.fcr31 = data;
+			break;
+#endif /* CONFIG_MIPS_FP_SUPPORT */
+		case PC:
+			regs->cp0_epc = data;
+			break;
+		case MMHI:
+			regs->hi = data;
+			break;
+		case MMLO:
+			regs->lo = data;
+			break;
+		case DSP_BASE ... DSP_BASE + 5: {
+			dspreg_t *dregs;
+
+			if (!cpu_has_dsp) {
+				ret = -EIO;
+				break;
+			}
+
+			dregs = __get_dsp_regs(child);
+			dregs[addr - DSP_BASE] = data;
+			break;
+		}
+		case DSP_CONTROL:
+			if (!cpu_has_dsp) {
+				ret = -EIO;
+				break;
+			}
+			child->thread.dsp.dspcontrol = data;
+			break;
+		default:
+			/* The rest are not allowed. */
+			ret = -EIO;
+			break;
+		}
+		break;
+		}
+
+	case PTRACE_GETREGS:
+		ret = ptrace_getregs(child,
+				(struct user_pt_regs __user *) (__u64) data);
+		break;
+
+	case PTRACE_SETREGS:
+		ret = ptrace_setregs(child,
+				(struct user_pt_regs __user *) (__u64) data);
+		break;
+
+#ifdef CONFIG_MIPS_FP_SUPPORT
+	case PTRACE_GETFPREGS:
+		ret = ptrace_getfpregs(child, (__u32 __user *) (__u64) data);
+		break;
+
+	case PTRACE_SETFPREGS:
+		ret = ptrace_setfpregs(child, (__u32 __user *) (__u64) data);
+		break;
+#endif
+	case PTRACE_GET_THREAD_AREA:
+		ret = put_user(task_thread_info(child)->tp_value,
+				(unsigned int __user *) (unsigned long) data);
+		break;
+
+	case PTRACE_GET_THREAD_AREA_3264:
+		ret = put_user(task_thread_info(child)->tp_value,
+				(unsigned long __user *) (unsigned long) data);
+		break;
+
+	case PTRACE_GET_WATCH_REGS:
+		ret = ptrace_get_watch_regs(child,
+			(struct pt_watch_regs __user *) (unsigned long) addr);
+		break;
+
+	case PTRACE_SET_WATCH_REGS:
+		ret = ptrace_set_watch_regs(child,
+			(struct pt_watch_regs __user *) (unsigned long) addr);
+		break;
+
+	default:
+		ret = compat_ptrace_request(child, request, addr, data);
+		break;
+	}
+out:
+	return ret;
+}
diff --git a/arch/mips/kernel/r2300_fpu.S b/arch/mips/kernel/r2300_fpu.S
new file mode 100644
index 000000000..2748c5582
--- /dev/null
+++ b/arch/mips/kernel/r2300_fpu.S
@@ -0,0 +1,130 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1996, 1998 by Ralf Baechle
+ *
+ * Multi-arch abstraction and asm macros for easier reading:
+ * Copyright (C) 1996 David S. Miller (davem@davemloft.net)
+ *
+ * Further modifications to make this work:
+ * Copyright (c) 1998 Harald Koerfgen
+ */
+#include <asm/asm.h>
+#include <asm/asmmacro.h>
+#include <asm/errno.h>
+#include <asm/export.h>
+#include <asm/fpregdef.h>
+#include <asm/mipsregs.h>
+#include <asm/asm-offsets.h>
+#include <asm/regdef.h>
+
+#define EX(a,b)							\
+9:	a,##b;							\
+	.section __ex_table,"a";				\
+	PTR_WD	9b,fault;					\
+	.previous
+
+#define EX2(a,b)						\
+9:	a,##b;							\
+	.section __ex_table,"a";				\
+	PTR_WD	9b,fault;					\
+	PTR_WD	9b+4,fault;					\
+	.previous
+
+	.set	mips1
+
+/*
+ * Save a thread's fp context.
+ */
+LEAF(_save_fp)
+EXPORT_SYMBOL(_save_fp)
+	fpu_save_single a0, t1			# clobbers t1
+	jr	ra
+	END(_save_fp)
+
+/*
+ * Restore a thread's fp context.
+ */
+LEAF(_restore_fp)
+	fpu_restore_single a0, t1		# clobbers t1
+	jr	ra
+	END(_restore_fp)
+
+	.set	noreorder
+
+/**
+ * _save_fp_context() - save FP context from the FPU
+ * @a0 - pointer to fpregs field of sigcontext
+ * @a1 - pointer to fpc_csr field of sigcontext
+ *
+ * Save FP context, including the 32 FP data registers and the FP
+ * control & status register, from the FPU to signal context.
+ */
+LEAF(_save_fp_context)
+	.set	push
+	SET_HARDFLOAT
+	li	v0, 0					# assume success
+	cfc1	t1, fcr31
+	EX2(s.d $f0, 0(a0))
+	EX2(s.d $f2, 16(a0))
+	EX2(s.d $f4, 32(a0))
+	EX2(s.d $f6, 48(a0))
+	EX2(s.d $f8, 64(a0))
+	EX2(s.d $f10, 80(a0))
+	EX2(s.d $f12, 96(a0))
+	EX2(s.d $f14, 112(a0))
+	EX2(s.d $f16, 128(a0))
+	EX2(s.d $f18, 144(a0))
+	EX2(s.d $f20, 160(a0))
+	EX2(s.d $f22, 176(a0))
+	EX2(s.d $f24, 192(a0))
+	EX2(s.d $f26, 208(a0))
+	EX2(s.d $f28, 224(a0))
+	EX2(s.d $f30, 240(a0))
+	jr	ra
+	 EX(sw	t1, (a1))
+	.set	pop
+	END(_save_fp_context)
+
+/**
+ * _restore_fp_context() - restore FP context to the FPU
+ * @a0 - pointer to fpregs field of sigcontext
+ * @a1 - pointer to fpc_csr field of sigcontext
+ *
+ * Restore FP context, including the 32 FP data registers and the FP
+ * control & status register, from signal context to the FPU.
+ */
+LEAF(_restore_fp_context)
+	.set	push
+	SET_HARDFLOAT
+	li	v0, 0					# assume success
+	EX(lw t0, (a1))
+	EX2(l.d $f0, 0(a0))
+	EX2(l.d $f2, 16(a0))
+	EX2(l.d $f4, 32(a0))
+	EX2(l.d $f6, 48(a0))
+	EX2(l.d $f8, 64(a0))
+	EX2(l.d $f10, 80(a0))
+	EX2(l.d $f12, 96(a0))
+	EX2(l.d $f14, 112(a0))
+	EX2(l.d $f16, 128(a0))
+	EX2(l.d $f18, 144(a0))
+	EX2(l.d $f20, 160(a0))
+	EX2(l.d $f22, 176(a0))
+	EX2(l.d $f24, 192(a0))
+	EX2(l.d $f26, 208(a0))
+	EX2(l.d $f28, 224(a0))
+	EX2(l.d $f30, 240(a0))
+	jr	ra
+	 ctc1	t0, fcr31
+	.set	pop
+	END(_restore_fp_context)
+	.set	reorder
+
+	.type	fault, @function
+	.ent	fault
+fault:	li	v0, -EFAULT
+	jr	ra
+	.end	fault
diff --git a/arch/mips/kernel/r2300_switch.S b/arch/mips/kernel/r2300_switch.S
new file mode 100644
index 000000000..71b1aafae
--- /dev/null
+++ b/arch/mips/kernel/r2300_switch.S
@@ -0,0 +1,65 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * r2300_switch.S: R2300 specific task switching code.
+ *
+ * Copyright (C) 1994, 1995, 1996, 1999 by Ralf Baechle
+ * Copyright (C) 1994, 1995, 1996 by Andreas Busse
+ *
+ * Multi-cpu abstraction and macros for easier reading:
+ * Copyright (C) 1996 David S. Miller (davem@davemloft.net)
+ *
+ * Further modifications to make this work:
+ * Copyright (c) 1998-2000 Harald Koerfgen
+ */
+#include <asm/asm.h>
+#include <asm/cachectl.h>
+#include <asm/export.h>
+#include <asm/fpregdef.h>
+#include <asm/mipsregs.h>
+#include <asm/asm-offsets.h>
+#include <asm/regdef.h>
+#include <asm/stackframe.h>
+#include <asm/thread_info.h>
+
+#include <asm/asmmacro.h>
+
+	.set	mips1
+	.align	5
+
+/*
+ * task_struct *resume(task_struct *prev, task_struct *next,
+ *		       struct thread_info *next_ti)
+ */
+LEAF(resume)
+	mfc0	t1, CP0_STATUS
+	sw	t1, THREAD_STATUS(a0)
+	cpu_save_nonscratch a0
+	sw	ra, THREAD_REG31(a0)
+
+#if defined(CONFIG_STACKPROTECTOR) && !defined(CONFIG_SMP)
+	PTR_LA	t8, __stack_chk_guard
+	LONG_L	t9, TASK_STACK_CANARY(a1)
+	LONG_S	t9, 0(t8)
+#endif
+
+	/*
+	 * The order of restoring the registers takes care of the race
+	 * updating $28, $29 and kernelsp without disabling ints.
+	 */
+	move	$28, a2
+	cpu_restore_nonscratch a1
+
+	addiu	t1, $28, _THREAD_SIZE - 32
+	sw	t1, kernelsp
+
+	mfc0	t1, CP0_STATUS		/* Do we really need this? */
+	li	a3, 0xff01
+	and	t1, a3
+	lw	a2, THREAD_STATUS(a1)
+	nor	a3, $0, a3
+	and	a2, a3
+	or	a2, t1
+	mtc0	a2, CP0_STATUS
+	move	v0, a0
+	jr	ra
+	END(resume)
diff --git a/arch/mips/kernel/r4k-bugs64.c b/arch/mips/kernel/r4k-bugs64.c
new file mode 100644
index 000000000..6ffefb2c6
--- /dev/null
+++ b/arch/mips/kernel/r4k-bugs64.c
@@ -0,0 +1,325 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2003, 2004, 2007  Maciej W. Rozycki
+ */
+#include <linux/context_tracking.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/ptrace.h>
+#include <linux/stddef.h>
+
+#include <asm/bugs.h>
+#include <asm/compiler.h>
+#include <asm/cpu.h>
+#include <asm/fpu.h>
+#include <asm/mipsregs.h>
+#include <asm/setup.h>
+
+static char bug64hit[] __initdata =
+	"reliable operation impossible!\n%s";
+static char nowar[] __initdata =
+	"Please report to <linux-mips@vger.kernel.org>.";
+static char r4kwar[] __initdata =
+	"Enable CPU_R4000_WORKAROUNDS to rectify.";
+static char daddiwar[] __initdata =
+	"Enable CPU_DADDI_WORKAROUNDS to rectify.";
+
+static __always_inline __init
+void align_mod(const int align, const int mod)
+{
+	asm volatile(
+		".set	push\n\t"
+		".set	noreorder\n\t"
+		".balign %0\n\t"
+		".rept	%1\n\t"
+		"nop\n\t"
+		".endr\n\t"
+		".set	pop"
+		:
+		: "n"(align), "n"(mod));
+}
+
+static __always_inline __init
+void mult_sh_align_mod(long *v1, long *v2, long *w,
+		       const int align, const int mod)
+{
+	unsigned long flags;
+	int m1, m2;
+	long p, s, lv1, lv2, lw;
+
+	/*
+	 * We want the multiply and the shift to be isolated from the
+	 * rest of the code to disable gcc optimizations.  Hence the
+	 * asm statements that execute nothing, but make gcc not know
+	 * what the values of m1, m2 and s are and what lv2 and p are
+	 * used for.
+	 */
+
+	local_irq_save(flags);
+	/*
+	 * The following code leads to a wrong result of the first
+	 * dsll32 when executed on R4000 rev. 2.2 or 3.0 (PRId
+	 * 00000422 or 00000430, respectively).
+	 *
+	 * See "MIPS R4000PC/SC Errata, Processor Revision 2.2 and
+	 * 3.0" by MIPS Technologies, Inc., errata #16 and #28 for
+	 * details.  I got no permission to duplicate them here,
+	 * sigh... --macro
+	 */
+	asm volatile(
+		""
+		: "=r" (m1), "=r" (m2), "=r" (s)
+		: "0" (5), "1" (8), "2" (5));
+	align_mod(align, mod);
+	/*
+	 * The trailing nop is needed to fulfill the two-instruction
+	 * requirement between reading hi/lo and staring a mult/div.
+	 * Leaving it out may cause gas insert a nop itself breaking
+	 * the desired alignment of the next chunk.
+	 */
+	asm volatile(
+		".set	push\n\t"
+		".set	noat\n\t"
+		".set	noreorder\n\t"
+		".set	nomacro\n\t"
+		"mult	%2, %3\n\t"
+		"dsll32 %0, %4, %5\n\t"
+		"mflo	$0\n\t"
+		"dsll32 %1, %4, %5\n\t"
+		"nop\n\t"
+		".set	pop"
+		: "=&r" (lv1), "=r" (lw)
+		: "r" (m1), "r" (m2), "r" (s), "I" (0)
+		: "hi", "lo", "$0");
+	/* We have to use single integers for m1 and m2 and a double
+	 * one for p to be sure the mulsidi3 gcc's RTL multiplication
+	 * instruction has the workaround applied.  Older versions of
+	 * gcc have correct umulsi3 and mulsi3, but other
+	 * multiplication variants lack the workaround.
+	 */
+	asm volatile(
+		""
+		: "=r" (m1), "=r" (m2), "=r" (s)
+		: "0" (m1), "1" (m2), "2" (s));
+	align_mod(align, mod);
+	p = m1 * m2;
+	lv2 = s << 32;
+	asm volatile(
+		""
+		: "=r" (lv2)
+		: "0" (lv2), "r" (p));
+	local_irq_restore(flags);
+
+	*v1 = lv1;
+	*v2 = lv2;
+	*w = lw;
+}
+
+static __always_inline __init void check_mult_sh(void)
+{
+	long v1[8], v2[8], w[8];
+	int bug, fix, i;
+
+	printk("Checking for the multiply/shift bug... ");
+
+	/*
+	 * Testing discovered false negatives for certain code offsets
+	 * into cache lines.  Hence we test all possible offsets for
+	 * the worst assumption of an R4000 I-cache line width of 32
+	 * bytes.
+	 *
+	 * We can't use a loop as alignment directives need to be
+	 * immediates.
+	 */
+	mult_sh_align_mod(&v1[0], &v2[0], &w[0], 32, 0);
+	mult_sh_align_mod(&v1[1], &v2[1], &w[1], 32, 1);
+	mult_sh_align_mod(&v1[2], &v2[2], &w[2], 32, 2);
+	mult_sh_align_mod(&v1[3], &v2[3], &w[3], 32, 3);
+	mult_sh_align_mod(&v1[4], &v2[4], &w[4], 32, 4);
+	mult_sh_align_mod(&v1[5], &v2[5], &w[5], 32, 5);
+	mult_sh_align_mod(&v1[6], &v2[6], &w[6], 32, 6);
+	mult_sh_align_mod(&v1[7], &v2[7], &w[7], 32, 7);
+
+	bug = 0;
+	for (i = 0; i < 8; i++)
+		if (v1[i] != w[i])
+			bug = 1;
+
+	if (bug == 0) {
+		pr_cont("no.\n");
+		return;
+	}
+
+	pr_cont("yes, workaround... ");
+
+	fix = 1;
+	for (i = 0; i < 8; i++)
+		if (v2[i] != w[i])
+			fix = 0;
+
+	if (fix == 1) {
+		pr_cont("yes.\n");
+		return;
+	}
+
+	pr_cont("no.\n");
+	panic(bug64hit,
+	      IS_ENABLED(CONFIG_CPU_R4000_WORKAROUNDS) ? nowar : r4kwar);
+}
+
+static volatile int daddi_ov;
+
+asmlinkage void __init do_daddi_ov(struct pt_regs *regs)
+{
+	enum ctx_state prev_state;
+
+	prev_state = exception_enter();
+	daddi_ov = 1;
+	regs->cp0_epc += 4;
+	exception_exit(prev_state);
+}
+
+static __init void check_daddi(void)
+{
+	extern asmlinkage void handle_daddi_ov(void);
+	unsigned long flags;
+	void *handler;
+	long v, tmp;
+
+	printk("Checking for the daddi bug... ");
+
+	local_irq_save(flags);
+	handler = set_except_vector(EXCCODE_OV, handle_daddi_ov);
+	/*
+	 * The following code fails to trigger an overflow exception
+	 * when executed on R4000 rev. 2.2 or 3.0 (PRId 00000422 or
+	 * 00000430, respectively).
+	 *
+	 * See "MIPS R4000PC/SC Errata, Processor Revision 2.2 and
+	 * 3.0" by MIPS Technologies, Inc., erratum #23 for details.
+	 * I got no permission to duplicate it here, sigh... --macro
+	 */
+	asm volatile(
+		".set	push\n\t"
+		".set	noat\n\t"
+		".set	noreorder\n\t"
+		".set	nomacro\n\t"
+		"addiu	%1, $0, %2\n\t"
+		"dsrl	%1, %1, 1\n\t"
+#ifdef HAVE_AS_SET_DADDI
+		".set	daddi\n\t"
+#endif
+		"daddi	%0, %1, %3\n\t"
+		".set	pop"
+		: "=r" (v), "=&r" (tmp)
+		: "I" (0xffffffffffffdb9aUL), "I" (0x1234));
+	set_except_vector(EXCCODE_OV, handler);
+	local_irq_restore(flags);
+
+	if (daddi_ov) {
+		pr_cont("no.\n");
+		return;
+	}
+
+	pr_cont("yes, workaround... ");
+
+	local_irq_save(flags);
+	handler = set_except_vector(EXCCODE_OV, handle_daddi_ov);
+	asm volatile(
+		"addiu	%1, $0, %2\n\t"
+		"dsrl	%1, %1, 1\n\t"
+		"daddi	%0, %1, %3"
+		: "=r" (v), "=&r" (tmp)
+		: "I" (0xffffffffffffdb9aUL), "I" (0x1234));
+	set_except_vector(EXCCODE_OV, handler);
+	local_irq_restore(flags);
+
+	if (daddi_ov) {
+		pr_cont("yes.\n");
+		return;
+	}
+
+	pr_cont("no.\n");
+	panic(bug64hit,
+	      IS_ENABLED(CONFIG_CPU_DADDI_WORKAROUNDS) ? nowar : daddiwar);
+}
+
+int daddiu_bug	= -1;
+
+static __init void check_daddiu(void)
+{
+	long v, w, tmp;
+
+	printk("Checking for the daddiu bug... ");
+
+	/*
+	 * The following code leads to a wrong result of daddiu when
+	 * executed on R4400 rev. 1.0 (PRId 00000440).
+	 *
+	 * See "MIPS R4400PC/SC Errata, Processor Revision 1.0" by
+	 * MIPS Technologies, Inc., erratum #7 for details.
+	 *
+	 * According to "MIPS R4000PC/SC Errata, Processor Revision
+	 * 2.2 and 3.0" by MIPS Technologies, Inc., erratum #41 this
+	 * problem affects R4000 rev. 2.2 and 3.0 (PRId 00000422 and
+	 * 00000430, respectively), too.  Testing failed to trigger it
+	 * so far.
+	 *
+	 * I got no permission to duplicate the errata here, sigh...
+	 * --macro
+	 */
+	asm volatile(
+		".set	push\n\t"
+		".set	noat\n\t"
+		".set	noreorder\n\t"
+		".set	nomacro\n\t"
+		"addiu	%2, $0, %3\n\t"
+		"dsrl	%2, %2, 1\n\t"
+#ifdef HAVE_AS_SET_DADDI
+		".set	daddi\n\t"
+#endif
+		"daddiu %0, %2, %4\n\t"
+		"addiu	%1, $0, %4\n\t"
+		"daddu	%1, %2\n\t"
+		".set	pop"
+		: "=&r" (v), "=&r" (w), "=&r" (tmp)
+		: "I" (0xffffffffffffdb9aUL), "I" (0x1234));
+
+	daddiu_bug = v != w;
+
+	if (!daddiu_bug) {
+		pr_cont("no.\n");
+		return;
+	}
+
+	pr_cont("yes, workaround... ");
+
+	asm volatile(
+		"addiu	%2, $0, %3\n\t"
+		"dsrl	%2, %2, 1\n\t"
+		"daddiu %0, %2, %4\n\t"
+		"addiu	%1, $0, %4\n\t"
+		"daddu	%1, %2"
+		: "=&r" (v), "=&r" (w), "=&r" (tmp)
+		: "I" (0xffffffffffffdb9aUL), "I" (0x1234));
+
+	if (v == w) {
+		pr_cont("yes.\n");
+		return;
+	}
+
+	pr_cont("no.\n");
+	panic(bug64hit,
+	      IS_ENABLED(CONFIG_CPU_DADDI_WORKAROUNDS) ? nowar : daddiwar);
+}
+
+void __init check_bugs64_early(void)
+{
+	check_mult_sh();
+	check_daddiu();
+}
+
+void __init check_bugs64(void)
+{
+	check_daddi();
+}
diff --git a/arch/mips/kernel/r4k_fpu.S b/arch/mips/kernel/r4k_fpu.S
new file mode 100644
index 000000000..2e687c60b
--- /dev/null
+++ b/arch/mips/kernel/r4k_fpu.S
@@ -0,0 +1,417 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1996, 98, 99, 2000, 01 Ralf Baechle
+ *
+ * Multi-arch abstraction and asm macros for easier reading:
+ * Copyright (C) 1996 David S. Miller (davem@davemloft.net)
+ *
+ * Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 2000 MIPS Technologies, Inc.
+ * Copyright (C) 1999, 2001 Silicon Graphics, Inc.
+ */
+#include <asm/asm.h>
+#include <asm/asmmacro.h>
+#include <asm/errno.h>
+#include <asm/export.h>
+#include <asm/fpregdef.h>
+#include <asm/mipsregs.h>
+#include <asm/asm-offsets.h>
+#include <asm/regdef.h>
+
+/* preprocessor replaces the fp in ".set fp=64" with $30 otherwise */
+#undef fp
+
+	.macro	EX insn, reg, src
+	.set	push
+	SET_HARDFLOAT
+	.set	nomacro
+.ex\@:	\insn	\reg, \src
+	.set	pop
+	.section __ex_table,"a"
+	PTR_WD	.ex\@, fault
+	.previous
+	.endm
+
+/*
+ * Save a thread's fp context.
+ */
+LEAF(_save_fp)
+EXPORT_SYMBOL(_save_fp)
+#if defined(CONFIG_64BIT) || defined(CONFIG_CPU_MIPSR2) || \
+    defined(CONFIG_CPU_MIPSR5) || defined(CONFIG_CPU_MIPSR6)
+	mfc0	t0, CP0_STATUS
+#endif
+	fpu_save_double a0 t0 t1		# clobbers t1
+	jr	ra
+	END(_save_fp)
+
+/*
+ * Restore a thread's fp context.
+ */
+LEAF(_restore_fp)
+#if defined(CONFIG_64BIT) || defined(CONFIG_CPU_MIPSR2) || \
+    defined(CONFIG_CPU_MIPSR5) || defined(CONFIG_CPU_MIPSR6)
+	mfc0	t0, CP0_STATUS
+#endif
+	fpu_restore_double a0 t0 t1		# clobbers t1
+	jr	ra
+	END(_restore_fp)
+
+#ifdef CONFIG_CPU_HAS_MSA
+
+/*
+ * Save a thread's MSA vector context.
+ */
+LEAF(_save_msa)
+EXPORT_SYMBOL(_save_msa)
+	msa_save_all	a0
+	jr	ra
+	END(_save_msa)
+
+/*
+ * Restore a thread's MSA vector context.
+ */
+LEAF(_restore_msa)
+	msa_restore_all	a0
+	jr	ra
+	END(_restore_msa)
+
+LEAF(_init_msa_upper)
+	msa_init_all_upper
+	jr	ra
+	END(_init_msa_upper)
+
+#endif
+
+	.set	noreorder
+
+/**
+ * _save_fp_context() - save FP context from the FPU
+ * @a0 - pointer to fpregs field of sigcontext
+ * @a1 - pointer to fpc_csr field of sigcontext
+ *
+ * Save FP context, including the 32 FP data registers and the FP
+ * control & status register, from the FPU to signal context.
+ */
+LEAF(_save_fp_context)
+	.set	push
+	SET_HARDFLOAT
+	cfc1	t1, fcr31
+	.set	pop
+
+#if defined(CONFIG_64BIT) || defined(CONFIG_CPU_MIPSR2) || \
+    defined(CONFIG_CPU_MIPSR5) || defined(CONFIG_CPU_MIPSR6)
+	.set	push
+	SET_HARDFLOAT
+#if defined(CONFIG_CPU_MIPSR2) || defined(CONFIG_CPU_MIPSR5)
+	.set	mips32r2
+	.set	fp=64
+	mfc0	t0, CP0_STATUS
+	sll	t0, t0, 5
+	bgez	t0, 1f			# skip storing odd if FR=0
+	 nop
+#endif
+	/* Store the 16 odd double precision registers */
+	EX	sdc1 $f1, 8(a0)
+	EX	sdc1 $f3, 24(a0)
+	EX	sdc1 $f5, 40(a0)
+	EX	sdc1 $f7, 56(a0)
+	EX	sdc1 $f9, 72(a0)
+	EX	sdc1 $f11, 88(a0)
+	EX	sdc1 $f13, 104(a0)
+	EX	sdc1 $f15, 120(a0)
+	EX	sdc1 $f17, 136(a0)
+	EX	sdc1 $f19, 152(a0)
+	EX	sdc1 $f21, 168(a0)
+	EX	sdc1 $f23, 184(a0)
+	EX	sdc1 $f25, 200(a0)
+	EX	sdc1 $f27, 216(a0)
+	EX	sdc1 $f29, 232(a0)
+	EX	sdc1 $f31, 248(a0)
+1:	.set	pop
+#endif
+
+	.set push
+	SET_HARDFLOAT
+	/* Store the 16 even double precision registers */
+	EX	sdc1 $f0, 0(a0)
+	EX	sdc1 $f2, 16(a0)
+	EX	sdc1 $f4, 32(a0)
+	EX	sdc1 $f6, 48(a0)
+	EX	sdc1 $f8, 64(a0)
+	EX	sdc1 $f10, 80(a0)
+	EX	sdc1 $f12, 96(a0)
+	EX	sdc1 $f14, 112(a0)
+	EX	sdc1 $f16, 128(a0)
+	EX	sdc1 $f18, 144(a0)
+	EX	sdc1 $f20, 160(a0)
+	EX	sdc1 $f22, 176(a0)
+	EX	sdc1 $f24, 192(a0)
+	EX	sdc1 $f26, 208(a0)
+	EX	sdc1 $f28, 224(a0)
+	EX	sdc1 $f30, 240(a0)
+	EX	sw t1, 0(a1)
+	jr	ra
+	 li	v0, 0					# success
+	.set pop
+	END(_save_fp_context)
+
+/**
+ * _restore_fp_context() - restore FP context to the FPU
+ * @a0 - pointer to fpregs field of sigcontext
+ * @a1 - pointer to fpc_csr field of sigcontext
+ *
+ * Restore FP context, including the 32 FP data registers and the FP
+ * control & status register, from signal context to the FPU.
+ */
+LEAF(_restore_fp_context)
+	EX	lw t1, 0(a1)
+
+#if defined(CONFIG_64BIT) || defined(CONFIG_CPU_MIPSR2) || \
+    defined(CONFIG_CPU_MIPSR5) || defined(CONFIG_CPU_MIPSR6)
+	.set	push
+	SET_HARDFLOAT
+#if defined(CONFIG_CPU_MIPSR2) || defined(CONFIG_CPU_MIPSR5)
+	.set	mips32r2
+	.set	fp=64
+	mfc0	t0, CP0_STATUS
+	sll	t0, t0, 5
+	bgez	t0, 1f			# skip loading odd if FR=0
+	 nop
+#endif
+	EX	ldc1 $f1, 8(a0)
+	EX	ldc1 $f3, 24(a0)
+	EX	ldc1 $f5, 40(a0)
+	EX	ldc1 $f7, 56(a0)
+	EX	ldc1 $f9, 72(a0)
+	EX	ldc1 $f11, 88(a0)
+	EX	ldc1 $f13, 104(a0)
+	EX	ldc1 $f15, 120(a0)
+	EX	ldc1 $f17, 136(a0)
+	EX	ldc1 $f19, 152(a0)
+	EX	ldc1 $f21, 168(a0)
+	EX	ldc1 $f23, 184(a0)
+	EX	ldc1 $f25, 200(a0)
+	EX	ldc1 $f27, 216(a0)
+	EX	ldc1 $f29, 232(a0)
+	EX	ldc1 $f31, 248(a0)
+1:	.set pop
+#endif
+	.set push
+	SET_HARDFLOAT
+	EX	ldc1 $f0, 0(a0)
+	EX	ldc1 $f2, 16(a0)
+	EX	ldc1 $f4, 32(a0)
+	EX	ldc1 $f6, 48(a0)
+	EX	ldc1 $f8, 64(a0)
+	EX	ldc1 $f10, 80(a0)
+	EX	ldc1 $f12, 96(a0)
+	EX	ldc1 $f14, 112(a0)
+	EX	ldc1 $f16, 128(a0)
+	EX	ldc1 $f18, 144(a0)
+	EX	ldc1 $f20, 160(a0)
+	EX	ldc1 $f22, 176(a0)
+	EX	ldc1 $f24, 192(a0)
+	EX	ldc1 $f26, 208(a0)
+	EX	ldc1 $f28, 224(a0)
+	EX	ldc1 $f30, 240(a0)
+	ctc1	t1, fcr31
+	.set pop
+	jr	ra
+	 li	v0, 0					# success
+	END(_restore_fp_context)
+
+#ifdef CONFIG_CPU_HAS_MSA
+
+	.macro	op_one_wr	op, idx, base
+	.align	4
+\idx:	\op	\idx, 0, \base
+	jr	ra
+	 nop
+	.endm
+
+	.macro	op_msa_wr	name, op
+LEAF(\name)
+	.set		push
+	.set		noreorder
+	sll		t0, a0, 4
+	PTR_LA		t1, 0f
+	PTR_ADDU	t0, t0, t1
+	jr		t0
+	  nop
+	op_one_wr	\op, 0, a1
+	op_one_wr	\op, 1, a1
+	op_one_wr	\op, 2, a1
+	op_one_wr	\op, 3, a1
+	op_one_wr	\op, 4, a1
+	op_one_wr	\op, 5, a1
+	op_one_wr	\op, 6, a1
+	op_one_wr	\op, 7, a1
+	op_one_wr	\op, 8, a1
+	op_one_wr	\op, 9, a1
+	op_one_wr	\op, 10, a1
+	op_one_wr	\op, 11, a1
+	op_one_wr	\op, 12, a1
+	op_one_wr	\op, 13, a1
+	op_one_wr	\op, 14, a1
+	op_one_wr	\op, 15, a1
+	op_one_wr	\op, 16, a1
+	op_one_wr	\op, 17, a1
+	op_one_wr	\op, 18, a1
+	op_one_wr	\op, 19, a1
+	op_one_wr	\op, 20, a1
+	op_one_wr	\op, 21, a1
+	op_one_wr	\op, 22, a1
+	op_one_wr	\op, 23, a1
+	op_one_wr	\op, 24, a1
+	op_one_wr	\op, 25, a1
+	op_one_wr	\op, 26, a1
+	op_one_wr	\op, 27, a1
+	op_one_wr	\op, 28, a1
+	op_one_wr	\op, 29, a1
+	op_one_wr	\op, 30, a1
+	op_one_wr	\op, 31, a1
+	.set		pop
+	END(\name)
+	.endm
+
+	op_msa_wr	read_msa_wr_b, st_b
+	op_msa_wr	read_msa_wr_h, st_h
+	op_msa_wr	read_msa_wr_w, st_w
+	op_msa_wr	read_msa_wr_d, st_d
+
+	op_msa_wr	write_msa_wr_b, ld_b
+	op_msa_wr	write_msa_wr_h, ld_h
+	op_msa_wr	write_msa_wr_w, ld_w
+	op_msa_wr	write_msa_wr_d, ld_d
+
+#endif /* CONFIG_CPU_HAS_MSA */
+
+#ifdef CONFIG_CPU_HAS_MSA
+
+	.macro	save_msa_upper	wr, off, base
+	.set	push
+	.set	noat
+#ifdef CONFIG_64BIT
+	copy_s_d \wr, 1
+	EX sd	$1, \off(\base)
+#elif defined(CONFIG_CPU_LITTLE_ENDIAN)
+	copy_s_w \wr, 2
+	EX sw	$1, \off(\base)
+	copy_s_w \wr, 3
+	EX sw	$1, (\off+4)(\base)
+#else /* CONFIG_CPU_BIG_ENDIAN */
+	copy_s_w \wr, 2
+	EX sw	$1, (\off+4)(\base)
+	copy_s_w \wr, 3
+	EX sw	$1, \off(\base)
+#endif
+	.set	pop
+	.endm
+
+LEAF(_save_msa_all_upper)
+	save_msa_upper	0, 0x00, a0
+	save_msa_upper	1, 0x08, a0
+	save_msa_upper	2, 0x10, a0
+	save_msa_upper	3, 0x18, a0
+	save_msa_upper	4, 0x20, a0
+	save_msa_upper	5, 0x28, a0
+	save_msa_upper	6, 0x30, a0
+	save_msa_upper	7, 0x38, a0
+	save_msa_upper	8, 0x40, a0
+	save_msa_upper	9, 0x48, a0
+	save_msa_upper	10, 0x50, a0
+	save_msa_upper	11, 0x58, a0
+	save_msa_upper	12, 0x60, a0
+	save_msa_upper	13, 0x68, a0
+	save_msa_upper	14, 0x70, a0
+	save_msa_upper	15, 0x78, a0
+	save_msa_upper	16, 0x80, a0
+	save_msa_upper	17, 0x88, a0
+	save_msa_upper	18, 0x90, a0
+	save_msa_upper	19, 0x98, a0
+	save_msa_upper	20, 0xa0, a0
+	save_msa_upper	21, 0xa8, a0
+	save_msa_upper	22, 0xb0, a0
+	save_msa_upper	23, 0xb8, a0
+	save_msa_upper	24, 0xc0, a0
+	save_msa_upper	25, 0xc8, a0
+	save_msa_upper	26, 0xd0, a0
+	save_msa_upper	27, 0xd8, a0
+	save_msa_upper	28, 0xe0, a0
+	save_msa_upper	29, 0xe8, a0
+	save_msa_upper	30, 0xf0, a0
+	save_msa_upper	31, 0xf8, a0
+	jr	ra
+	 li	v0, 0
+	END(_save_msa_all_upper)
+
+	.macro	restore_msa_upper	wr, off, base
+	.set	push
+	.set	noat
+#ifdef CONFIG_64BIT
+	EX ld	$1, \off(\base)
+	insert_d \wr, 1
+#elif defined(CONFIG_CPU_LITTLE_ENDIAN)
+	EX lw	$1, \off(\base)
+	insert_w \wr, 2
+	EX lw	$1, (\off+4)(\base)
+	insert_w \wr, 3
+#else /* CONFIG_CPU_BIG_ENDIAN */
+	EX lw	$1, (\off+4)(\base)
+	insert_w \wr, 2
+	EX lw	$1, \off(\base)
+	insert_w \wr, 3
+#endif
+	.set	pop
+	.endm
+
+LEAF(_restore_msa_all_upper)
+	restore_msa_upper	0, 0x00, a0
+	restore_msa_upper	1, 0x08, a0
+	restore_msa_upper	2, 0x10, a0
+	restore_msa_upper	3, 0x18, a0
+	restore_msa_upper	4, 0x20, a0
+	restore_msa_upper	5, 0x28, a0
+	restore_msa_upper	6, 0x30, a0
+	restore_msa_upper	7, 0x38, a0
+	restore_msa_upper	8, 0x40, a0
+	restore_msa_upper	9, 0x48, a0
+	restore_msa_upper	10, 0x50, a0
+	restore_msa_upper	11, 0x58, a0
+	restore_msa_upper	12, 0x60, a0
+	restore_msa_upper	13, 0x68, a0
+	restore_msa_upper	14, 0x70, a0
+	restore_msa_upper	15, 0x78, a0
+	restore_msa_upper	16, 0x80, a0
+	restore_msa_upper	17, 0x88, a0
+	restore_msa_upper	18, 0x90, a0
+	restore_msa_upper	19, 0x98, a0
+	restore_msa_upper	20, 0xa0, a0
+	restore_msa_upper	21, 0xa8, a0
+	restore_msa_upper	22, 0xb0, a0
+	restore_msa_upper	23, 0xb8, a0
+	restore_msa_upper	24, 0xc0, a0
+	restore_msa_upper	25, 0xc8, a0
+	restore_msa_upper	26, 0xd0, a0
+	restore_msa_upper	27, 0xd8, a0
+	restore_msa_upper	28, 0xe0, a0
+	restore_msa_upper	29, 0xe8, a0
+	restore_msa_upper	30, 0xf0, a0
+	restore_msa_upper	31, 0xf8, a0
+	jr	ra
+	 li	v0, 0
+	END(_restore_msa_all_upper)
+
+#endif /* CONFIG_CPU_HAS_MSA */
+
+	.set	reorder
+
+	.type	fault, @function
+	.ent	fault
+fault:	li	v0, -EFAULT				# failure
+	jr	ra
+	.end	fault
diff --git a/arch/mips/kernel/r4k_switch.S b/arch/mips/kernel/r4k_switch.S
new file mode 100644
index 000000000..58232ae6c
--- /dev/null
+++ b/arch/mips/kernel/r4k_switch.S
@@ -0,0 +1,59 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994, 1995, 1996, 1998, 1999, 2002, 2003 Ralf Baechle
+ * Copyright (C) 1996 David S. Miller (davem@davemloft.net)
+ * Copyright (C) 1994, 1995, 1996, by Andreas Busse
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ * Copyright (C) 2000 MIPS Technologies, Inc.
+ *    written by Carsten Langgaard, carstenl@mips.com
+ */
+#include <asm/asm.h>
+#include <asm/cachectl.h>
+#include <asm/mipsregs.h>
+#include <asm/asm-offsets.h>
+#include <asm/regdef.h>
+#include <asm/stackframe.h>
+#include <asm/thread_info.h>
+
+#include <asm/asmmacro.h>
+
+/*
+ * task_struct *resume(task_struct *prev, task_struct *next,
+ *		       struct thread_info *next_ti)
+ */
+	.align	5
+	LEAF(resume)
+	mfc0	t1, CP0_STATUS
+	LONG_S	t1, THREAD_STATUS(a0)
+	cpu_save_nonscratch a0
+	LONG_S	ra, THREAD_REG31(a0)
+
+#if defined(CONFIG_STACKPROTECTOR) && !defined(CONFIG_SMP)
+	PTR_LA	t8, __stack_chk_guard
+	LONG_L	t9, TASK_STACK_CANARY(a1)
+	LONG_S	t9, 0(t8)
+#endif
+
+	/*
+	 * The order of restoring the registers takes care of the race
+	 * updating $28, $29 and kernelsp without disabling ints.
+	 */
+	move	$28, a2
+	cpu_restore_nonscratch a1
+
+	PTR_ADDU	t0, $28, _THREAD_SIZE - 32
+	set_saved_sp	t0, t1, t2
+	mfc0	t1, CP0_STATUS		/* Do we really need this? */
+	li	a3, 0xff01
+	and	t1, a3
+	LONG_L	a2, THREAD_STATUS(a1)
+	nor	a3, $0, a3
+	and	a2, a3
+	or	a2, t1
+	mtc0	a2, CP0_STATUS
+	move	v0, a0
+	jr	ra
+	END(resume)
diff --git a/arch/mips/kernel/relocate.c b/arch/mips/kernel/relocate.c
new file mode 100644
index 000000000..58fc8d089
--- /dev/null
+++ b/arch/mips/kernel/relocate.c
@@ -0,0 +1,466 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Support for Kernel relocation at boot time
+ *
+ * Copyright (C) 2015, Imagination Technologies Ltd.
+ * Authors: Matt Redfearn (matt.redfearn@mips.com)
+ */
+#include <asm/bootinfo.h>
+#include <asm/cacheflush.h>
+#include <asm/fw/fw.h>
+#include <asm/sections.h>
+#include <asm/setup.h>
+#include <asm/timex.h>
+#include <linux/elf.h>
+#include <linux/kernel.h>
+#include <linux/libfdt.h>
+#include <linux/of_fdt.h>
+#include <linux/panic_notifier.h>
+#include <linux/sched/task.h>
+#include <linux/start_kernel.h>
+#include <linux/string.h>
+#include <linux/printk.h>
+
+#define RELOCATED(x) ((void *)((long)x + offset))
+
+extern u32 _relocation_start[];	/* End kernel image / start relocation table */
+extern u32 _relocation_end[];	/* End relocation table */
+
+extern long __start___ex_table;	/* Start exception table */
+extern long __stop___ex_table;	/* End exception table */
+
+extern void __weak plat_fdt_relocated(void *new_location);
+
+/*
+ * This function may be defined for a platform to perform any post-relocation
+ * fixup necessary.
+ * Return non-zero to abort relocation
+ */
+int __weak plat_post_relocation(long offset)
+{
+	return 0;
+}
+
+static inline u32 __init get_synci_step(void)
+{
+	u32 res;
+
+	__asm__("rdhwr  %0, $1" : "=r" (res));
+
+	return res;
+}
+
+static void __init sync_icache(void *kbase, unsigned long kernel_length)
+{
+	void *kend = kbase + kernel_length;
+	u32 step = get_synci_step();
+
+	do {
+		__asm__ __volatile__(
+			"synci  0(%0)"
+			: /* no output */
+			: "r" (kbase));
+
+		kbase += step;
+	} while (step && kbase < kend);
+
+	/* Completion barrier */
+	__sync();
+}
+
+static void __init apply_r_mips_64_rel(u32 *loc_new, long offset)
+{
+	*(u64 *)loc_new += offset;
+}
+
+static void __init apply_r_mips_32_rel(u32 *loc_new, long offset)
+{
+	*loc_new += offset;
+}
+
+static int __init apply_r_mips_26_rel(u32 *loc_orig, u32 *loc_new, long offset)
+{
+	unsigned long target_addr = (*loc_orig) & 0x03ffffff;
+
+	if (offset % 4) {
+		pr_err("Dangerous R_MIPS_26 REL relocation\n");
+		return -ENOEXEC;
+	}
+
+	/* Original target address */
+	target_addr <<= 2;
+	target_addr += (unsigned long)loc_orig & 0xf0000000;
+
+	/* Get the new target address */
+	target_addr += offset;
+
+	if ((target_addr & 0xf0000000) != ((unsigned long)loc_new & 0xf0000000)) {
+		pr_err("R_MIPS_26 REL relocation overflow\n");
+		return -ENOEXEC;
+	}
+
+	target_addr -= (unsigned long)loc_new & 0xf0000000;
+	target_addr >>= 2;
+
+	*loc_new = (*loc_new & ~0x03ffffff) | (target_addr & 0x03ffffff);
+
+	return 0;
+}
+
+
+static void __init apply_r_mips_hi16_rel(u32 *loc_orig, u32 *loc_new,
+					 long offset)
+{
+	unsigned long insn = *loc_orig;
+	unsigned long target = (insn & 0xffff) << 16; /* high 16bits of target */
+
+	target += offset;
+
+	*loc_new = (insn & ~0xffff) | ((target >> 16) & 0xffff);
+}
+
+static int __init reloc_handler(u32 type, u32 *loc_orig, u32 *loc_new,
+				long offset)
+{
+	switch (type) {
+	case R_MIPS_64:
+		apply_r_mips_64_rel(loc_new, offset);
+		break;
+	case R_MIPS_32:
+		apply_r_mips_32_rel(loc_new, offset);
+		break;
+	case R_MIPS_26:
+		return apply_r_mips_26_rel(loc_orig, loc_new, offset);
+	case R_MIPS_HI16:
+		apply_r_mips_hi16_rel(loc_orig, loc_new, offset);
+		break;
+	default:
+		pr_err("Unhandled relocation type %d at 0x%pK\n", type,
+		       loc_orig);
+		return -ENOEXEC;
+	}
+
+	return 0;
+}
+
+static int __init do_relocations(void *kbase_old, void *kbase_new, long offset)
+{
+	u32 *r;
+	u32 *loc_orig;
+	u32 *loc_new;
+	int type;
+	int res;
+
+	for (r = _relocation_start; r < _relocation_end; r++) {
+		/* Sentinel for last relocation */
+		if (*r == 0)
+			break;
+
+		type = (*r >> 24) & 0xff;
+		loc_orig = kbase_old + ((*r & 0x00ffffff) << 2);
+		loc_new = RELOCATED(loc_orig);
+
+		res = reloc_handler(type, loc_orig, loc_new, offset);
+		if (res)
+			return res;
+	}
+
+	return 0;
+}
+
+/*
+ * The exception table is filled in by the relocs tool after vmlinux is linked.
+ * It must be relocated separately since there will not be any relocation
+ * information for it filled in by the linker.
+ */
+static int __init relocate_exception_table(long offset)
+{
+	unsigned long *etable_start, *etable_end, *e;
+
+	etable_start = RELOCATED(&__start___ex_table);
+	etable_end = RELOCATED(&__stop___ex_table);
+
+	for (e = etable_start; e < etable_end; e++)
+		*e += offset;
+
+	return 0;
+}
+
+#ifdef CONFIG_RANDOMIZE_BASE
+
+static inline __init unsigned long rotate_xor(unsigned long hash,
+					      const void *area, size_t size)
+{
+	const typeof(hash) *ptr = PTR_ALIGN(area, sizeof(hash));
+	size_t diff, i;
+
+	diff = (void *)ptr - area;
+	if (unlikely(size < diff + sizeof(hash)))
+		return hash;
+
+	size = ALIGN_DOWN(size - diff, sizeof(hash));
+
+	for (i = 0; i < size / sizeof(hash); i++) {
+		/* Rotate by odd number of bits and XOR. */
+		hash = (hash << ((sizeof(hash) * 8) - 7)) | (hash >> 7);
+		hash ^= ptr[i];
+	}
+
+	return hash;
+}
+
+static inline __init unsigned long get_random_boot(void)
+{
+	unsigned long entropy = random_get_entropy();
+	unsigned long hash = 0;
+
+	/* Attempt to create a simple but unpredictable starting entropy. */
+	hash = rotate_xor(hash, linux_banner, strlen(linux_banner));
+
+	/* Add in any runtime entropy we can get */
+	hash = rotate_xor(hash, &entropy, sizeof(entropy));
+
+#if defined(CONFIG_USE_OF)
+	/* Get any additional entropy passed in device tree */
+	if (initial_boot_params) {
+		int node, len;
+		u64 *prop;
+
+		node = fdt_path_offset(initial_boot_params, "/chosen");
+		if (node >= 0) {
+			prop = fdt_getprop_w(initial_boot_params, node,
+					     "kaslr-seed", &len);
+			if (prop && (len == sizeof(u64)))
+				hash = rotate_xor(hash, prop, sizeof(*prop));
+		}
+	}
+#endif /* CONFIG_USE_OF */
+
+	return hash;
+}
+
+static inline __init bool kaslr_disabled(void)
+{
+	char *str;
+
+#if defined(CONFIG_CMDLINE_BOOL)
+	const char *builtin_cmdline = CONFIG_CMDLINE;
+
+	str = strstr(builtin_cmdline, "nokaslr");
+	if (str == builtin_cmdline ||
+	    (str > builtin_cmdline && *(str - 1) == ' '))
+		return true;
+#endif
+	str = strstr(arcs_cmdline, "nokaslr");
+	if (str == arcs_cmdline || (str > arcs_cmdline && *(str - 1) == ' '))
+		return true;
+
+	return false;
+}
+
+static inline void __init *determine_relocation_address(void)
+{
+	/* Choose a new address for the kernel */
+	unsigned long kernel_length;
+	void *dest = &_text;
+	unsigned long offset;
+
+	if (kaslr_disabled())
+		return dest;
+
+	kernel_length = (long)_end - (long)(&_text);
+
+	offset = get_random_boot() << 16;
+	offset &= (CONFIG_RANDOMIZE_BASE_MAX_OFFSET - 1);
+	if (offset < kernel_length)
+		offset += ALIGN(kernel_length, 0xffff);
+
+	return RELOCATED(dest);
+}
+
+#else
+
+static inline void __init *determine_relocation_address(void)
+{
+	/*
+	 * Choose a new address for the kernel
+	 * For now we'll hard code the destination
+	 */
+	return (void *)0xffffffff81000000;
+}
+
+#endif
+
+static inline int __init relocation_addr_valid(void *loc_new)
+{
+	if ((unsigned long)loc_new & 0x0000ffff) {
+		/* Inappropriately aligned new location */
+		return 0;
+	}
+	if ((unsigned long)loc_new < (unsigned long)&_end) {
+		/* New location overlaps original kernel */
+		return 0;
+	}
+	return 1;
+}
+
+static inline void __init update_kaslr_offset(unsigned long *addr, long offset)
+{
+	unsigned long *new_addr = (unsigned long *)RELOCATED(addr);
+
+	*new_addr = (unsigned long)offset;
+}
+
+#if defined(CONFIG_USE_OF)
+void __weak *plat_get_fdt(void)
+{
+	return NULL;
+}
+#endif
+
+void *__init relocate_kernel(void)
+{
+	void *loc_new;
+	unsigned long kernel_length;
+	unsigned long bss_length;
+	long offset = 0;
+	int res = 1;
+	/* Default to original kernel entry point */
+	void *kernel_entry = start_kernel;
+	void *fdt = NULL;
+
+	/* Get the command line */
+	fw_init_cmdline();
+#if defined(CONFIG_USE_OF)
+	/* Deal with the device tree */
+	fdt = plat_get_fdt();
+	early_init_dt_scan(fdt);
+	if (boot_command_line[0]) {
+		/* Boot command line was passed in device tree */
+		strscpy(arcs_cmdline, boot_command_line, COMMAND_LINE_SIZE);
+	}
+#endif /* CONFIG_USE_OF */
+
+	kernel_length = (long)(&_relocation_start) - (long)(&_text);
+	bss_length = (long)&__bss_stop - (long)&__bss_start;
+
+	loc_new = determine_relocation_address();
+
+	/* Sanity check relocation address */
+	if (relocation_addr_valid(loc_new))
+		offset = (unsigned long)loc_new - (unsigned long)(&_text);
+
+	/* Reset the command line now so we don't end up with a duplicate */
+	arcs_cmdline[0] = '\0';
+
+	if (offset) {
+		void (*fdt_relocated_)(void *) = NULL;
+#if defined(CONFIG_USE_OF)
+		unsigned long fdt_phys = virt_to_phys(fdt);
+
+		/*
+		 * If built-in dtb is used then it will have been relocated
+		 * during kernel _text relocation. If appended DTB is used
+		 * then it will not be relocated, but it should remain
+		 * intact in the original location. If dtb is loaded by
+		 * the bootloader then it may need to be moved if it crosses
+		 * the target memory area
+		 */
+
+		if (fdt_phys >= virt_to_phys(RELOCATED(&_text)) &&
+			fdt_phys <= virt_to_phys(RELOCATED(&_end))) {
+			void *fdt_relocated =
+				RELOCATED(ALIGN((long)&_end, PAGE_SIZE));
+			memcpy(fdt_relocated, fdt, fdt_totalsize(fdt));
+			fdt = fdt_relocated;
+			fdt_relocated_ = RELOCATED(&plat_fdt_relocated);
+		}
+#endif /* CONFIG_USE_OF */
+
+		/* Copy the kernel to it's new location */
+		memcpy(loc_new, &_text, kernel_length);
+
+		/* Perform relocations on the new kernel */
+		res = do_relocations(&_text, loc_new, offset);
+		if (res < 0)
+			goto out;
+
+		/* Sync the caches ready for execution of new kernel */
+		sync_icache(loc_new, kernel_length);
+
+		res = relocate_exception_table(offset);
+		if (res < 0)
+			goto out;
+
+		/*
+		 * The original .bss has already been cleared, and
+		 * some variables such as command line parameters
+		 * stored to it so make a copy in the new location.
+		 */
+		memcpy(RELOCATED(&__bss_start), &__bss_start, bss_length);
+
+		/*
+		 * If fdt was stored outside of the kernel image and
+		 * had to be moved then update platform's state data
+		 * with the new fdt location
+		 */
+		if (fdt_relocated_)
+			fdt_relocated_(fdt);
+
+		/*
+		 * Last chance for the platform to abort relocation.
+		 * This may also be used by the platform to perform any
+		 * initialisation required now that the new kernel is
+		 * resident in memory and ready to be executed.
+		 */
+		if (plat_post_relocation(offset))
+			goto out;
+
+		/* The current thread is now within the relocated image */
+		__current_thread_info = RELOCATED(&init_thread_union);
+
+		/* Return the new kernel's entry point */
+		kernel_entry = RELOCATED(start_kernel);
+
+		/* Error may occur before, so keep it at last */
+		update_kaslr_offset(&__kaslr_offset, offset);
+	}
+out:
+	return kernel_entry;
+}
+
+/*
+ * Show relocation information on panic.
+ */
+static void show_kernel_relocation(const char *level)
+{
+	if (__kaslr_offset > 0) {
+		printk(level);
+		pr_cont("Kernel relocated by 0x%pK\n", (void *)__kaslr_offset);
+		pr_cont(" .text @ 0x%pK\n", _text);
+		pr_cont(" .data @ 0x%pK\n", _sdata);
+		pr_cont(" .bss  @ 0x%pK\n", __bss_start);
+	}
+}
+
+static int kernel_location_notifier_fn(struct notifier_block *self,
+				       unsigned long v, void *p)
+{
+	show_kernel_relocation(KERN_EMERG);
+	return NOTIFY_DONE;
+}
+
+static struct notifier_block kernel_location_notifier = {
+	.notifier_call = kernel_location_notifier_fn
+};
+
+static int __init register_kernel_offset_dumper(void)
+{
+	atomic_notifier_chain_register(&panic_notifier_list,
+				       &kernel_location_notifier);
+	return 0;
+}
+__initcall(register_kernel_offset_dumper);
diff --git a/arch/mips/kernel/relocate_kernel.S b/arch/mips/kernel/relocate_kernel.S
new file mode 100644
index 000000000..f5b2ef979
--- /dev/null
+++ b/arch/mips/kernel/relocate_kernel.S
@@ -0,0 +1,184 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * relocate_kernel.S for kexec
+ * Created by <nschichan@corp.free.fr> on Thu Oct 12 17:49:57 2006
+ */
+
+#include <asm/asm.h>
+#include <asm/asmmacro.h>
+#include <asm/regdef.h>
+#include <asm/mipsregs.h>
+#include <asm/stackframe.h>
+#include <asm/addrspace.h>
+
+#include <kernel-entry-init.h>
+
+LEAF(relocate_new_kernel)
+	PTR_L a0,	arg0
+	PTR_L a1,	arg1
+	PTR_L a2,	arg2
+	PTR_L a3,	arg3
+
+	PTR_L		s0, kexec_indirection_page
+	PTR_L		s1, kexec_start_address
+
+process_entry:
+	PTR_L		s2, (s0)
+	PTR_ADDIU	s0, s0, SZREG
+
+	/*
+	 * In case of a kdump/crash kernel, the indirection page is not
+	 * populated as the kernel is directly copied to a reserved location
+	 */
+	beqz		s2, done
+
+	/* destination page */
+	and		s3, s2, 0x1
+	beq		s3, zero, 1f
+	and		s4, s2, ~0x1	/* store destination addr in s4 */
+	b		process_entry
+
+1:
+	/* indirection page, update s0	*/
+	and		s3, s2, 0x2
+	beq		s3, zero, 1f
+	and		s0, s2, ~0x2
+	b		process_entry
+
+1:
+	/* done page */
+	and		s3, s2, 0x4
+	beq		s3, zero, 1f
+	b		done
+1:
+	/* source page */
+	and		s3, s2, 0x8
+	beq		s3, zero, process_entry
+	and		s2, s2, ~0x8
+	li		s6, (1 << _PAGE_SHIFT) / SZREG
+
+copy_word:
+	/* copy page word by word */
+	REG_L		s5, (s2)
+	REG_S		s5, (s4)
+	PTR_ADDIU	s4, s4, SZREG
+	PTR_ADDIU	s2, s2, SZREG
+	LONG_ADDIU	s6, s6, -1
+	beq		s6, zero, process_entry
+	b		copy_word
+	b		process_entry
+
+done:
+#ifdef CONFIG_SMP
+	/* kexec_flag reset is signal to other CPUs what kernel
+	   was moved to it's location. Note - we need relocated address
+	   of kexec_flag.  */
+
+	bal		1f
+ 1:	move		t1,ra;
+	PTR_LA		t2,1b
+	PTR_LA		t0,kexec_flag
+	PTR_SUB		t0,t0,t2;
+	PTR_ADD		t0,t1,t0;
+	LONG_S		zero,(t0)
+#endif
+
+#ifdef CONFIG_CPU_CAVIUM_OCTEON
+	/* We need to flush I-cache before jumping to new kernel.
+	 * Unfortunately, this code is cpu-specific.
+	 */
+	.set push
+	.set noreorder
+	syncw
+	syncw
+	synci		0($0)
+	.set pop
+#else
+	sync
+#endif
+	/* jump to kexec_start_address */
+	j		s1
+	END(relocate_new_kernel)
+
+#ifdef CONFIG_SMP
+/*
+ * Other CPUs should wait until code is relocated and
+ * then start at entry (?) point.
+ */
+LEAF(kexec_smp_wait)
+	PTR_L		a0, s_arg0
+	PTR_L		a1, s_arg1
+	PTR_L		a2, s_arg2
+	PTR_L		a3, s_arg3
+	PTR_L		s1, kexec_start_address
+
+	/* Non-relocated address works for args and kexec_start_address ( old
+	 * kernel is not overwritten). But we need relocated address of
+	 * kexec_flag.
+	 */
+
+	bal		1f
+1:	move		t1,ra;
+	PTR_LA		t2,1b
+	PTR_LA		t0,kexec_flag
+	PTR_SUB		t0,t0,t2;
+	PTR_ADD		t0,t1,t0;
+
+1:	LONG_L		s0, (t0)
+	bne		s0, zero,1b
+
+#ifdef USE_KEXEC_SMP_WAIT_FINAL
+	kexec_smp_wait_final
+#else
+	sync
+#endif
+	j		s1
+	END(kexec_smp_wait)
+#endif
+
+#ifdef __mips64
+       /* all PTR's must be aligned to 8 byte in 64-bit mode */
+       .align  3
+#endif
+
+/* All parameters to new kernel are passed in registers a0-a3.
+ * kexec_args[0..3] are used to prepare register values.
+ */
+
+EXPORT(kexec_args)
+arg0:	PTR_WD		0x0
+arg1:	PTR_WD		0x0
+arg2:	PTR_WD		0x0
+arg3:	PTR_WD		0x0
+	.size	kexec_args,PTRSIZE*4
+
+#ifdef CONFIG_SMP
+/*
+ * Secondary CPUs may have different kernel parameters in
+ * their registers a0-a3. secondary_kexec_args[0..3] are used
+ * to prepare register values.
+ */
+EXPORT(secondary_kexec_args)
+s_arg0: PTR_WD		0x0
+s_arg1: PTR_WD		0x0
+s_arg2: PTR_WD		0x0
+s_arg3: PTR_WD		0x0
+	.size	secondary_kexec_args,PTRSIZE*4
+kexec_flag:
+	LONG		0x1
+
+#endif
+
+EXPORT(kexec_start_address)
+	PTR_WD		0x0
+	.size		kexec_start_address, PTRSIZE
+
+EXPORT(kexec_indirection_page)
+	PTR_WD		0
+	.size		kexec_indirection_page, PTRSIZE
+
+relocate_new_kernel_end:
+
+EXPORT(relocate_new_kernel_size)
+	PTR_WD		relocate_new_kernel_end - relocate_new_kernel
+	.size		relocate_new_kernel_size, PTRSIZE
diff --git a/arch/mips/kernel/reset.c b/arch/mips/kernel/reset.c
new file mode 100644
index 000000000..e7ce07b3e
--- /dev/null
+++ b/arch/mips/kernel/reset.c
@@ -0,0 +1,124 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2001, 06 by Ralf Baechle (ralf@linux-mips.org)
+ * Copyright (C) 2001 MIPS Technologies, Inc.
+ */
+#include <linux/kernel.h>
+#include <linux/export.h>
+#include <linux/pm.h>
+#include <linux/types.h>
+#include <linux/reboot.h>
+#include <linux/delay.h>
+
+#include <asm/compiler.h>
+#include <asm/idle.h>
+#include <asm/mipsregs.h>
+#include <asm/reboot.h>
+
+/*
+ * Urgs ...  Too many MIPS machines to handle this in a generic way.
+ * So handle all using function pointers to machine specific
+ * functions.
+ */
+void (*_machine_restart)(char *command);
+void (*_machine_halt)(void);
+void (*pm_power_off)(void);
+
+EXPORT_SYMBOL(pm_power_off);
+
+static void machine_hang(void)
+{
+	/*
+	 * We're hanging the system so we don't want to be interrupted anymore.
+	 * Any interrupt handlers that ran would at best be useless & at worst
+	 * go awry because the system isn't in a functional state.
+	 */
+	local_irq_disable();
+
+	/*
+	 * Mask all interrupts, giving us a better chance of remaining in the
+	 * low power wait state.
+	 */
+	clear_c0_status(ST0_IM);
+
+	while (true) {
+		if (cpu_has_mips_r) {
+			/*
+			 * We know that the wait instruction is supported so
+			 * make use of it directly, leaving interrupts
+			 * disabled.
+			 */
+			asm volatile(
+				".set	push\n\t"
+				".set	" MIPS_ISA_ARCH_LEVEL "\n\t"
+				"wait\n\t"
+				".set	pop");
+		} else if (cpu_wait) {
+			/*
+			 * Try the cpu_wait() callback. This isn't ideal since
+			 * it'll re-enable interrupts, but that ought to be
+			 * harmless given that they're all masked.
+			 */
+			cpu_wait();
+			local_irq_disable();
+		} else {
+			/*
+			 * We're going to burn some power running round the
+			 * loop, but we don't really have a choice. This isn't
+			 * a path we should expect to run for long during
+			 * typical use anyway.
+			 */
+		}
+
+		/*
+		 * In most modern MIPS CPUs interrupts will cause the wait
+		 * instruction to graduate even when disabled, and in some
+		 * cases even when masked. In order to prevent a timer
+		 * interrupt from continuously taking us out of the low power
+		 * wait state, we clear any pending timer interrupt here.
+		 */
+		if (cpu_has_counter)
+			write_c0_compare(0);
+	}
+}
+
+void machine_restart(char *command)
+{
+	if (_machine_restart)
+		_machine_restart(command);
+
+#ifdef CONFIG_SMP
+	preempt_disable();
+	smp_send_stop();
+#endif
+	do_kernel_restart(command);
+	mdelay(1000);
+	pr_emerg("Reboot failed -- System halted\n");
+	machine_hang();
+}
+
+void machine_halt(void)
+{
+	if (_machine_halt)
+		_machine_halt();
+
+#ifdef CONFIG_SMP
+	preempt_disable();
+	smp_send_stop();
+#endif
+	machine_hang();
+}
+
+void machine_power_off(void)
+{
+	do_kernel_power_off();
+
+#ifdef CONFIG_SMP
+	preempt_disable();
+	smp_send_stop();
+#endif
+	machine_hang();
+}
diff --git a/arch/mips/kernel/rtlx-cmp.c b/arch/mips/kernel/rtlx-cmp.c
new file mode 100644
index 000000000..d26dcc4b4
--- /dev/null
+++ b/arch/mips/kernel/rtlx-cmp.c
@@ -0,0 +1,122 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2005 MIPS Technologies, Inc.  All rights reserved.
+ * Copyright (C) 2013 Imagination Technologies Ltd.
+ */
+#include <linux/device.h>
+#include <linux/fs.h>
+#include <linux/err.h>
+#include <linux/wait.h>
+#include <linux/sched.h>
+#include <linux/smp.h>
+
+#include <asm/mips_mt.h>
+#include <asm/vpe.h>
+#include <asm/rtlx.h>
+
+static int major;
+
+static void rtlx_interrupt(void)
+{
+	int i;
+	struct rtlx_info *info;
+	struct rtlx_info **p = vpe_get_shared(aprp_cpu_index());
+
+	if (p == NULL || *p == NULL)
+		return;
+
+	info = *p;
+
+	if (info->ap_int_pending == 1 && smp_processor_id() == 0) {
+		for (i = 0; i < RTLX_CHANNELS; i++) {
+			wake_up(&channel_wqs[i].lx_queue);
+			wake_up(&channel_wqs[i].rt_queue);
+		}
+		info->ap_int_pending = 0;
+	}
+}
+
+void _interrupt_sp(void)
+{
+	smp_send_reschedule(aprp_cpu_index());
+}
+
+int __init rtlx_module_init(void)
+{
+	struct device *dev;
+	int i, err;
+
+	if (!cpu_has_mipsmt) {
+		pr_warn("VPE loader: not a MIPS MT capable processor\n");
+		return -ENODEV;
+	}
+
+	if (num_possible_cpus() - aprp_cpu_index() < 1) {
+		pr_warn("No TCs reserved for AP/SP, not initializing RTLX.\n"
+			"Pass maxcpus=<n> argument as kernel argument\n");
+
+		return -ENODEV;
+	}
+
+	major = register_chrdev(0, RTLX_MODULE_NAME, &rtlx_fops);
+	if (major < 0) {
+		pr_err("rtlx_module_init: unable to register device\n");
+		return major;
+	}
+
+	/* initialise the wait queues */
+	for (i = 0; i < RTLX_CHANNELS; i++) {
+		init_waitqueue_head(&channel_wqs[i].rt_queue);
+		init_waitqueue_head(&channel_wqs[i].lx_queue);
+		atomic_set(&channel_wqs[i].in_open, 0);
+		mutex_init(&channel_wqs[i].mutex);
+
+		dev = device_create(mt_class, NULL, MKDEV(major, i), NULL,
+				    "%s%d", RTLX_MODULE_NAME, i);
+		if (IS_ERR(dev)) {
+			while (i--)
+				device_destroy(mt_class, MKDEV(major, i));
+
+			err = PTR_ERR(dev);
+			goto out_chrdev;
+		}
+	}
+
+	/* set up notifiers */
+	rtlx_notify.start = rtlx_starting;
+	rtlx_notify.stop = rtlx_stopping;
+	vpe_notify(aprp_cpu_index(), &rtlx_notify);
+
+	if (cpu_has_vint) {
+		aprp_hook = rtlx_interrupt;
+	} else {
+		pr_err("APRP RTLX init on non-vectored-interrupt processor\n");
+		err = -ENODEV;
+		goto out_class;
+	}
+
+	return 0;
+
+out_class:
+	for (i = 0; i < RTLX_CHANNELS; i++)
+		device_destroy(mt_class, MKDEV(major, i));
+out_chrdev:
+	unregister_chrdev(major, RTLX_MODULE_NAME);
+
+	return err;
+}
+
+void __exit rtlx_module_exit(void)
+{
+	int i;
+
+	for (i = 0; i < RTLX_CHANNELS; i++)
+		device_destroy(mt_class, MKDEV(major, i));
+
+	unregister_chrdev(major, RTLX_MODULE_NAME);
+
+	aprp_hook = NULL;
+}
diff --git a/arch/mips/kernel/rtlx-mt.c b/arch/mips/kernel/rtlx-mt.c
new file mode 100644
index 000000000..38c6925a1
--- /dev/null
+++ b/arch/mips/kernel/rtlx-mt.c
@@ -0,0 +1,147 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2005 MIPS Technologies, Inc.  All rights reserved.
+ * Copyright (C) 2013 Imagination Technologies Ltd.
+ */
+#include <linux/device.h>
+#include <linux/fs.h>
+#include <linux/err.h>
+#include <linux/wait.h>
+#include <linux/sched.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+
+#include <asm/mips_mt.h>
+#include <asm/vpe.h>
+#include <asm/rtlx.h>
+
+static int major;
+
+static void rtlx_dispatch(void)
+{
+	if (read_c0_cause() & read_c0_status() & C_SW0)
+		do_IRQ(MIPS_CPU_IRQ_BASE + MIPS_CPU_RTLX_IRQ);
+}
+
+/*
+ * Interrupt handler may be called before rtlx_init has otherwise had
+ * a chance to run.
+ */
+static irqreturn_t rtlx_interrupt(int irq, void *dev_id)
+{
+	unsigned int vpeflags;
+	unsigned long flags;
+	int i;
+
+	local_irq_save(flags);
+	vpeflags = dvpe();
+	set_c0_status(0x100 << MIPS_CPU_RTLX_IRQ);
+	irq_enable_hazard();
+	evpe(vpeflags);
+	local_irq_restore(flags);
+
+	for (i = 0; i < RTLX_CHANNELS; i++) {
+		wake_up(&channel_wqs[i].lx_queue);
+		wake_up(&channel_wqs[i].rt_queue);
+	}
+
+	return IRQ_HANDLED;
+}
+
+static int rtlx_irq_num = MIPS_CPU_IRQ_BASE + MIPS_CPU_RTLX_IRQ;
+
+void _interrupt_sp(void)
+{
+	unsigned long flags;
+
+	local_irq_save(flags);
+	dvpe();
+	settc(1);
+	write_vpe_c0_cause(read_vpe_c0_cause() | C_SW0);
+	evpe(EVPE_ENABLE);
+	local_irq_restore(flags);
+}
+
+int __init rtlx_module_init(void)
+{
+	struct device *dev;
+	int i, err;
+
+	if (!cpu_has_mipsmt) {
+		pr_warn("VPE loader: not a MIPS MT capable processor\n");
+		return -ENODEV;
+	}
+
+	if (aprp_cpu_index() == 0) {
+		pr_warn("No TCs reserved for AP/SP, not initializing RTLX.\n"
+			"Pass maxtcs=<n> argument as kernel argument\n");
+
+		return -ENODEV;
+	}
+
+	major = register_chrdev(0, RTLX_MODULE_NAME, &rtlx_fops);
+	if (major < 0) {
+		pr_err("rtlx_module_init: unable to register device\n");
+		return major;
+	}
+
+	/* initialise the wait queues */
+	for (i = 0; i < RTLX_CHANNELS; i++) {
+		init_waitqueue_head(&channel_wqs[i].rt_queue);
+		init_waitqueue_head(&channel_wqs[i].lx_queue);
+		atomic_set(&channel_wqs[i].in_open, 0);
+		mutex_init(&channel_wqs[i].mutex);
+
+		dev = device_create(mt_class, NULL, MKDEV(major, i), NULL,
+				    "%s%d", RTLX_MODULE_NAME, i);
+		if (IS_ERR(dev)) {
+			while (i--)
+				device_destroy(mt_class, MKDEV(major, i));
+
+			err = PTR_ERR(dev);
+			goto out_chrdev;
+		}
+	}
+
+	/* set up notifiers */
+	rtlx_notify.start = rtlx_starting;
+	rtlx_notify.stop = rtlx_stopping;
+	vpe_notify(aprp_cpu_index(), &rtlx_notify);
+
+	if (cpu_has_vint) {
+		aprp_hook = rtlx_dispatch;
+	} else {
+		pr_err("APRP RTLX init on non-vectored-interrupt processor\n");
+		err = -ENODEV;
+		goto out_class;
+	}
+
+	err = request_irq(rtlx_irq_num, rtlx_interrupt, 0, "RTLX", rtlx);
+	if (err)
+		goto out_class;
+
+	return 0;
+
+out_class:
+	for (i = 0; i < RTLX_CHANNELS; i++)
+		device_destroy(mt_class, MKDEV(major, i));
+out_chrdev:
+	unregister_chrdev(major, RTLX_MODULE_NAME);
+
+	return err;
+}
+
+void __exit rtlx_module_exit(void)
+{
+	int i;
+
+	for (i = 0; i < RTLX_CHANNELS; i++)
+		device_destroy(mt_class, MKDEV(major, i));
+
+	unregister_chrdev(major, RTLX_MODULE_NAME);
+
+	aprp_hook = NULL;
+}
diff --git a/arch/mips/kernel/rtlx.c b/arch/mips/kernel/rtlx.c
new file mode 100644
index 000000000..18c509c59
--- /dev/null
+++ b/arch/mips/kernel/rtlx.c
@@ -0,0 +1,409 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2005 MIPS Technologies, Inc.  All rights reserved.
+ * Copyright (C) 2005, 06 Ralf Baechle (ralf@linux-mips.org)
+ * Copyright (C) 2013 Imagination Technologies Ltd.
+ */
+#include <linux/kernel.h>
+#include <linux/fs.h>
+#include <linux/syscalls.h>
+#include <linux/moduleloader.h>
+#include <linux/atomic.h>
+#include <linux/sched/signal.h>
+
+#include <asm/mipsmtregs.h>
+#include <asm/mips_mt.h>
+#include <asm/processor.h>
+#include <asm/rtlx.h>
+#include <asm/setup.h>
+#include <asm/vpe.h>
+
+static int sp_stopping;
+struct rtlx_info *rtlx;
+struct chan_waitqueues channel_wqs[RTLX_CHANNELS];
+struct vpe_notifications rtlx_notify;
+void (*aprp_hook)(void) = NULL;
+EXPORT_SYMBOL(aprp_hook);
+
+static void __used dump_rtlx(void)
+{
+	int i;
+
+	pr_info("id 0x%lx state %d\n", rtlx->id, rtlx->state);
+
+	for (i = 0; i < RTLX_CHANNELS; i++) {
+		struct rtlx_channel *chan = &rtlx->channel[i];
+
+		pr_info(" rt_state %d lx_state %d buffer_size %d\n",
+			chan->rt_state, chan->lx_state, chan->buffer_size);
+
+		pr_info(" rt_read %d rt_write %d\n",
+			chan->rt_read, chan->rt_write);
+
+		pr_info(" lx_read %d lx_write %d\n",
+			chan->lx_read, chan->lx_write);
+
+		pr_info(" rt_buffer <%s>\n", chan->rt_buffer);
+		pr_info(" lx_buffer <%s>\n", chan->lx_buffer);
+	}
+}
+
+/* call when we have the address of the shared structure from the SP side. */
+static int rtlx_init(struct rtlx_info *rtlxi)
+{
+	if (rtlxi->id != RTLX_ID) {
+		pr_err("no valid RTLX id at 0x%p 0x%lx\n", rtlxi, rtlxi->id);
+		return -ENOEXEC;
+	}
+
+	rtlx = rtlxi;
+
+	return 0;
+}
+
+/* notifications */
+void rtlx_starting(int vpe)
+{
+	int i;
+	sp_stopping = 0;
+
+	/* force a reload of rtlx */
+	rtlx = NULL;
+
+	/* wake up any sleeping rtlx_open's */
+	for (i = 0; i < RTLX_CHANNELS; i++)
+		wake_up_interruptible(&channel_wqs[i].lx_queue);
+}
+
+void rtlx_stopping(int vpe)
+{
+	int i;
+
+	sp_stopping = 1;
+	for (i = 0; i < RTLX_CHANNELS; i++)
+		wake_up_interruptible(&channel_wqs[i].lx_queue);
+}
+
+
+int rtlx_open(int index, int can_sleep)
+{
+	struct rtlx_info **p;
+	struct rtlx_channel *chan;
+	enum rtlx_state state;
+	int ret = 0;
+
+	if (index >= RTLX_CHANNELS) {
+		pr_debug("rtlx_open index out of range\n");
+		return -ENOSYS;
+	}
+
+	if (atomic_inc_return(&channel_wqs[index].in_open) > 1) {
+		pr_debug("rtlx_open channel %d already opened\n", index);
+		ret = -EBUSY;
+		goto out_fail;
+	}
+
+	if (rtlx == NULL) {
+		p = vpe_get_shared(aprp_cpu_index());
+		if (p == NULL) {
+			if (can_sleep) {
+				ret = __wait_event_interruptible(
+					channel_wqs[index].lx_queue,
+					(p = vpe_get_shared(aprp_cpu_index())));
+				if (ret)
+					goto out_fail;
+			} else {
+				pr_debug("No SP program loaded, and device opened with O_NONBLOCK\n");
+				ret = -ENOSYS;
+				goto out_fail;
+			}
+		}
+
+		smp_rmb();
+		if (*p == NULL) {
+			if (can_sleep) {
+				DEFINE_WAIT(wait);
+
+				for (;;) {
+					prepare_to_wait(
+						&channel_wqs[index].lx_queue,
+						&wait, TASK_INTERRUPTIBLE);
+					smp_rmb();
+					if (*p != NULL)
+						break;
+					if (!signal_pending(current)) {
+						schedule();
+						continue;
+					}
+					ret = -ERESTARTSYS;
+					goto out_fail;
+				}
+				finish_wait(&channel_wqs[index].lx_queue,
+					    &wait);
+			} else {
+				pr_err(" *vpe_get_shared is NULL. Has an SP program been loaded?\n");
+				ret = -ENOSYS;
+				goto out_fail;
+			}
+		}
+
+		if ((unsigned int)*p < KSEG0) {
+			pr_warn("vpe_get_shared returned an invalid pointer maybe an error code %d\n",
+				(int)*p);
+			ret = -ENOSYS;
+			goto out_fail;
+		}
+
+		ret = rtlx_init(*p);
+		if (ret < 0)
+			goto out_ret;
+	}
+
+	chan = &rtlx->channel[index];
+
+	state = xchg(&chan->lx_state, RTLX_STATE_OPENED);
+	if (state == RTLX_STATE_OPENED) {
+		ret = -EBUSY;
+		goto out_fail;
+	}
+
+out_fail:
+	smp_mb();
+	atomic_dec(&channel_wqs[index].in_open);
+	smp_mb();
+
+out_ret:
+	return ret;
+}
+
+int rtlx_release(int index)
+{
+	if (rtlx == NULL) {
+		pr_err("rtlx_release() with null rtlx\n");
+		return 0;
+	}
+	rtlx->channel[index].lx_state = RTLX_STATE_UNUSED;
+	return 0;
+}
+
+unsigned int rtlx_read_poll(int index, int can_sleep)
+{
+	struct rtlx_channel *chan;
+
+	if (rtlx == NULL)
+		return 0;
+
+	chan = &rtlx->channel[index];
+
+	/* data available to read? */
+	if (chan->lx_read == chan->lx_write) {
+		if (can_sleep) {
+			int ret = __wait_event_interruptible(
+				channel_wqs[index].lx_queue,
+				(chan->lx_read != chan->lx_write) ||
+				sp_stopping);
+			if (ret)
+				return ret;
+
+			if (sp_stopping)
+				return 0;
+		} else
+			return 0;
+	}
+
+	return (chan->lx_write + chan->buffer_size - chan->lx_read)
+	       % chan->buffer_size;
+}
+
+static inline int write_spacefree(int read, int write, int size)
+{
+	if (read == write) {
+		/*
+		 * Never fill the buffer completely, so indexes are always
+		 * equal if empty and only empty, or !equal if data available
+		 */
+		return size - 1;
+	}
+
+	return ((read + size - write) % size) - 1;
+}
+
+unsigned int rtlx_write_poll(int index)
+{
+	struct rtlx_channel *chan = &rtlx->channel[index];
+
+	return write_spacefree(chan->rt_read, chan->rt_write,
+				chan->buffer_size);
+}
+
+ssize_t rtlx_read(int index, void __user *buff, size_t count)
+{
+	size_t lx_write, fl = 0L;
+	struct rtlx_channel *lx;
+	unsigned long failed;
+
+	if (rtlx == NULL)
+		return -ENOSYS;
+
+	lx = &rtlx->channel[index];
+
+	mutex_lock(&channel_wqs[index].mutex);
+	smp_rmb();
+	lx_write = lx->lx_write;
+
+	/* find out how much in total */
+	count = min(count,
+		     (size_t)(lx_write + lx->buffer_size - lx->lx_read)
+		     % lx->buffer_size);
+
+	/* then how much from the read pointer onwards */
+	fl = min(count, (size_t)lx->buffer_size - lx->lx_read);
+
+	failed = copy_to_user(buff, lx->lx_buffer + lx->lx_read, fl);
+	if (failed)
+		goto out;
+
+	/* and if there is anything left at the beginning of the buffer */
+	if (count - fl)
+		failed = copy_to_user(buff + fl, lx->lx_buffer, count - fl);
+
+out:
+	count -= failed;
+
+	smp_wmb();
+	lx->lx_read = (lx->lx_read + count) % lx->buffer_size;
+	smp_wmb();
+	mutex_unlock(&channel_wqs[index].mutex);
+
+	return count;
+}
+
+ssize_t rtlx_write(int index, const void __user *buffer, size_t count)
+{
+	struct rtlx_channel *rt;
+	unsigned long failed;
+	size_t rt_read;
+	size_t fl;
+
+	if (rtlx == NULL)
+		return -ENOSYS;
+
+	rt = &rtlx->channel[index];
+
+	mutex_lock(&channel_wqs[index].mutex);
+	smp_rmb();
+	rt_read = rt->rt_read;
+
+	/* total number of bytes to copy */
+	count = min_t(size_t, count, write_spacefree(rt_read, rt->rt_write,
+						     rt->buffer_size));
+
+	/* first bit from write pointer to the end of the buffer, or count */
+	fl = min(count, (size_t) rt->buffer_size - rt->rt_write);
+
+	failed = copy_from_user(rt->rt_buffer + rt->rt_write, buffer, fl);
+	if (failed)
+		goto out;
+
+	/* if there's any left copy to the beginning of the buffer */
+	if (count - fl)
+		failed = copy_from_user(rt->rt_buffer, buffer + fl, count - fl);
+
+out:
+	count -= failed;
+
+	smp_wmb();
+	rt->rt_write = (rt->rt_write + count) % rt->buffer_size;
+	smp_wmb();
+	mutex_unlock(&channel_wqs[index].mutex);
+
+	_interrupt_sp();
+
+	return count;
+}
+
+
+static int file_open(struct inode *inode, struct file *filp)
+{
+	return rtlx_open(iminor(inode), (filp->f_flags & O_NONBLOCK) ? 0 : 1);
+}
+
+static int file_release(struct inode *inode, struct file *filp)
+{
+	return rtlx_release(iminor(inode));
+}
+
+static __poll_t file_poll(struct file *file, poll_table *wait)
+{
+	int minor = iminor(file_inode(file));
+	__poll_t mask = 0;
+
+	poll_wait(file, &channel_wqs[minor].rt_queue, wait);
+	poll_wait(file, &channel_wqs[minor].lx_queue, wait);
+
+	if (rtlx == NULL)
+		return 0;
+
+	/* data available to read? */
+	if (rtlx_read_poll(minor, 0))
+		mask |= EPOLLIN | EPOLLRDNORM;
+
+	/* space to write */
+	if (rtlx_write_poll(minor))
+		mask |= EPOLLOUT | EPOLLWRNORM;
+
+	return mask;
+}
+
+static ssize_t file_read(struct file *file, char __user *buffer, size_t count,
+			 loff_t *ppos)
+{
+	int minor = iminor(file_inode(file));
+
+	/* data available? */
+	if (!rtlx_read_poll(minor, (file->f_flags & O_NONBLOCK) ? 0 : 1))
+		return 0;	/* -EAGAIN makes 'cat' whine */
+
+	return rtlx_read(minor, buffer, count);
+}
+
+static ssize_t file_write(struct file *file, const char __user *buffer,
+			  size_t count, loff_t *ppos)
+{
+	int minor = iminor(file_inode(file));
+
+	/* any space left... */
+	if (!rtlx_write_poll(minor)) {
+		int ret;
+
+		if (file->f_flags & O_NONBLOCK)
+			return -EAGAIN;
+
+		ret = __wait_event_interruptible(channel_wqs[minor].rt_queue,
+					   rtlx_write_poll(minor));
+		if (ret)
+			return ret;
+	}
+
+	return rtlx_write(minor, buffer, count);
+}
+
+const struct file_operations rtlx_fops = {
+	.owner =   THIS_MODULE,
+	.open =    file_open,
+	.release = file_release,
+	.write =   file_write,
+	.read =    file_read,
+	.poll =    file_poll,
+	.llseek =  noop_llseek,
+};
+
+module_init(rtlx_module_init);
+module_exit(rtlx_module_exit);
+
+MODULE_DESCRIPTION("MIPS RTLX");
+MODULE_AUTHOR("Elizabeth Oldham, MIPS Technologies, Inc.");
+MODULE_LICENSE("GPL");
diff --git a/arch/mips/kernel/scall32-o32.S b/arch/mips/kernel/scall32-o32.S
new file mode 100644
index 000000000..18dc9b345
--- /dev/null
+++ b/arch/mips/kernel/scall32-o32.S
@@ -0,0 +1,222 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995-99, 2000- 02, 06 Ralf Baechle <ralf@linux-mips.org>
+ * Copyright (C) 2001 MIPS Technologies, Inc.
+ * Copyright (C) 2004 Thiemo Seufer
+ * Copyright (C) 2014 Imagination Technologies Ltd.
+ */
+#include <linux/errno.h>
+#include <asm/asm.h>
+#include <asm/asmmacro.h>
+#include <asm/irqflags.h>
+#include <asm/mipsregs.h>
+#include <asm/regdef.h>
+#include <asm/stackframe.h>
+#include <asm/isadep.h>
+#include <asm/sysmips.h>
+#include <asm/thread_info.h>
+#include <asm/unistd.h>
+#include <asm/asm-offsets.h>
+
+	.align	5
+NESTED(handle_sys, PT_SIZE, sp)
+	.set	noat
+	SAVE_SOME
+	TRACE_IRQS_ON_RELOAD
+	STI
+	.set	at
+
+	lw	t1, PT_EPC(sp)		# skip syscall on return
+
+	addiu	t1, 4			# skip to next instruction
+	sw	t1, PT_EPC(sp)
+
+	sw	a3, PT_R26(sp)		# save a3 for syscall restarting
+
+	/*
+	 * More than four arguments.  Try to deal with it by copying the
+	 * stack arguments from the user stack to the kernel stack.
+	 * This Sucks (TM).
+	 */
+	lw	t0, PT_R29(sp)		# get old user stack pointer
+
+	/*
+	 * We intentionally keep the kernel stack a little below the top of
+	 * userspace so we don't have to do a slower byte accurate check here.
+	 */
+	addu	t4, t0, 32
+	bltz	t4, bad_stack		# -> sp is bad
+
+	/*
+	 * Ok, copy the args from the luser stack to the kernel stack.
+	 */
+
+	.set    push
+	.set    noreorder
+	.set	nomacro
+
+load_a4: user_lw(t5, 16(t0))		# argument #5 from usp
+load_a5: user_lw(t6, 20(t0))		# argument #6 from usp
+load_a6: user_lw(t7, 24(t0))		# argument #7 from usp
+load_a7: user_lw(t8, 28(t0))		# argument #8 from usp
+loads_done:
+
+	sw	t5, 16(sp)		# argument #5 to ksp
+	sw	t6, 20(sp)		# argument #6 to ksp
+	sw	t7, 24(sp)		# argument #7 to ksp
+	sw	t8, 28(sp)		# argument #8 to ksp
+	.set	pop
+
+	.section __ex_table,"a"
+	PTR_WD	load_a4, bad_stack_a4
+	PTR_WD	load_a5, bad_stack_a5
+	PTR_WD	load_a6, bad_stack_a6
+	PTR_WD	load_a7, bad_stack_a7
+	.previous
+
+	lw	t0, TI_FLAGS($28)	# syscall tracing enabled?
+	li	t1, _TIF_WORK_SYSCALL_ENTRY
+	and	t0, t1
+	bnez	t0, syscall_trace_entry # -> yes
+syscall_common:
+	subu	v0, v0, __NR_O32_Linux	# check syscall number
+	sltiu	t0, v0, __NR_O32_Linux_syscalls
+	beqz	t0, illegal_syscall
+
+	sll	t0, v0, 2
+	la	t1, sys_call_table
+	addu	t1, t0
+	lw	t2, (t1)		# syscall routine
+
+	beqz	t2, illegal_syscall
+
+	jalr	t2			# Do The Real Thing (TM)
+
+	li	t0, -EMAXERRNO - 1	# error?
+	sltu	t0, t0, v0
+	sw	t0, PT_R7(sp)		# set error flag
+	beqz	t0, 1f
+
+	lw	t1, PT_R2(sp)		# syscall number
+	negu	v0			# error
+	sw	t1, PT_R0(sp)		# save it for syscall restarting
+1:	sw	v0, PT_R2(sp)		# result
+
+o32_syscall_exit:
+	j	syscall_exit_partial
+
+/* ------------------------------------------------------------------------ */
+
+syscall_trace_entry:
+	SAVE_STATIC
+	move	a0, sp
+
+	/*
+	 * syscall number is in v0 unless we called syscall(__NR_###)
+	 * where the real syscall number is in a0
+	 */
+	move	a1, v0
+	subu	t2, v0,  __NR_O32_Linux
+	bnez	t2, 1f /* __NR_syscall at offset 0 */
+	lw	a1, PT_R4(sp)
+
+1:	jal	syscall_trace_enter
+
+	bltz	v0, 1f			# seccomp failed? Skip syscall
+
+	RESTORE_STATIC
+	lw	v0, PT_R2(sp)		# Restore syscall (maybe modified)
+	lw	a0, PT_R4(sp)		# Restore argument registers
+	lw	a1, PT_R5(sp)
+	lw	a2, PT_R6(sp)
+	lw	a3, PT_R7(sp)
+	j	syscall_common
+
+1:	j	syscall_exit
+
+/* ------------------------------------------------------------------------ */
+
+	/*
+	 * Our open-coded access area sanity test for the stack pointer
+	 * failed. We probably should handle this case a bit more drastic.
+	 */
+bad_stack:
+	li	v0, EFAULT
+	sw	v0, PT_R2(sp)
+	li	t0, 1				# set error flag
+	sw	t0, PT_R7(sp)
+	j	o32_syscall_exit
+
+bad_stack_a4:
+	li	t5, 0
+	b	load_a5
+
+bad_stack_a5:
+	li	t6, 0
+	b	load_a6
+
+bad_stack_a6:
+	li	t7, 0
+	b	load_a7
+
+bad_stack_a7:
+	li	t8, 0
+	b	loads_done
+
+	/*
+	 * The system call does not exist in this kernel
+	 */
+illegal_syscall:
+	li	v0, ENOSYS			# error
+	sw	v0, PT_R2(sp)
+	li	t0, 1				# set error flag
+	sw	t0, PT_R7(sp)
+	j	o32_syscall_exit
+	END(handle_sys)
+
+	LEAF(sys_syscall)
+	subu	t0, a0, __NR_O32_Linux	# check syscall number
+	sltiu	v0, t0, __NR_O32_Linux_syscalls
+	beqz	t0, einval		# do not recurse
+	sll	t1, t0, 2
+	beqz	v0, einval
+	lw	t2, sys_call_table(t1)		# syscall routine
+
+	move	a0, a1				# shift argument registers
+	move	a1, a2
+	move	a2, a3
+	lw	a3, 16(sp)
+	lw	t4, 20(sp)
+	lw	t5, 24(sp)
+	lw	t6, 28(sp)
+	sw	t4, 16(sp)
+	sw	t5, 20(sp)
+	sw	t6, 24(sp)
+	jr	t2
+	/* Unreached */
+
+einval: li	v0, -ENOSYS
+	jr	ra
+	END(sys_syscall)
+
+#ifdef CONFIG_MIPS_MT_FPAFF
+	/*
+	 * For FPU affinity scheduling on MIPS MT processors, we need to
+	 * intercept sys_sched_xxxaffinity() calls until we get a proper hook
+	 * in kernel/sched/core.c.  Considered only temporary we only support
+	 * these hooks for the 32-bit kernel - there is no MIPS64 MT processor
+	 * atm.
+	 */
+#define sys_sched_setaffinity	mipsmt_sys_sched_setaffinity
+#define sys_sched_getaffinity	mipsmt_sys_sched_getaffinity
+#endif /* CONFIG_MIPS_MT_FPAFF */
+
+#define __SYSCALL_WITH_COMPAT(nr, native, compat)	__SYSCALL(nr, native)
+#define __SYSCALL(nr, entry) 	PTR_WD entry
+	.align	2
+	.type	sys_call_table, @object
+EXPORT(sys_call_table)
+#include <asm/syscall_table_o32.h>
diff --git a/arch/mips/kernel/scall64-n32.S b/arch/mips/kernel/scall64-n32.S
new file mode 100644
index 000000000..97456b2ca
--- /dev/null
+++ b/arch/mips/kernel/scall64-n32.S
@@ -0,0 +1,107 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995, 96, 97, 98, 99, 2000, 01 by Ralf Baechle
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ * Copyright (C) 2001 MIPS Technologies, Inc.
+ */
+#include <linux/errno.h>
+#include <asm/asm.h>
+#include <asm/asmmacro.h>
+#include <asm/irqflags.h>
+#include <asm/mipsregs.h>
+#include <asm/regdef.h>
+#include <asm/stackframe.h>
+#include <asm/thread_info.h>
+#include <asm/unistd.h>
+
+#ifndef CONFIG_MIPS32_O32
+/* No O32, so define handle_sys here */
+#define handle_sysn32 handle_sys
+#endif
+
+	.align	5
+NESTED(handle_sysn32, PT_SIZE, sp)
+#ifndef CONFIG_MIPS32_O32
+	.set	noat
+	SAVE_SOME
+	TRACE_IRQS_ON_RELOAD
+	STI
+	.set	at
+#endif
+
+	dsubu	t0, v0, __NR_N32_Linux	# check syscall number
+	sltiu	t0, t0, __NR_N32_Linux_syscalls
+
+#ifndef CONFIG_MIPS32_O32
+	ld	t1, PT_EPC(sp)		# skip syscall on return
+	daddiu	t1, 4			# skip to next instruction
+	sd	t1, PT_EPC(sp)
+#endif
+	beqz	t0, not_n32_scall
+
+	sd	a3, PT_R26(sp)		# save a3 for syscall restarting
+
+	li	t1, _TIF_WORK_SYSCALL_ENTRY
+	LONG_L	t0, TI_FLAGS($28)	# syscall tracing enabled?
+	and	t0, t1, t0
+	bnez	t0, n32_syscall_trace_entry
+
+syscall_common:
+	dsll	t0, v0, 3		# offset into table
+	ld	t2, (sysn32_call_table - (__NR_N32_Linux * 8))(t0)
+
+	jalr	t2			# Do The Real Thing (TM)
+
+	li	t0, -EMAXERRNO - 1	# error?
+	sltu	t0, t0, v0
+	sd	t0, PT_R7(sp)		# set error flag
+	beqz	t0, 1f
+
+	ld	t1, PT_R2(sp)		# syscall number
+	dnegu	v0			# error
+	sd	t1, PT_R0(sp)		# save it for syscall restarting
+1:	sd	v0, PT_R2(sp)		# result
+
+	j	syscall_exit_partial
+
+/* ------------------------------------------------------------------------ */
+
+n32_syscall_trace_entry:
+	SAVE_STATIC
+	move	a0, sp
+	move	a1, v0
+	jal	syscall_trace_enter
+
+	bltz	v0, 1f			# seccomp failed? Skip syscall
+
+	RESTORE_STATIC
+	ld	v0, PT_R2(sp)		# Restore syscall (maybe modified)
+	ld	a0, PT_R4(sp)		# Restore argument registers
+	ld	a1, PT_R5(sp)
+	ld	a2, PT_R6(sp)
+	ld	a3, PT_R7(sp)
+	ld	a4, PT_R8(sp)
+	ld	a5, PT_R9(sp)
+
+	dsubu	t2, v0, __NR_N32_Linux	# check (new) syscall number
+	sltiu   t0, t2, __NR_N32_Linux_syscalls
+	beqz	t0, not_n32_scall
+
+	j	syscall_common
+
+1:	j	syscall_exit
+
+not_n32_scall:
+	/* This is not an n32 compatibility syscall, pass it on to
+	   the n64 syscall handlers.  */
+	j	handle_sys64
+
+	END(handle_sysn32)
+
+#define __SYSCALL(nr, entry)	PTR_WD entry
+	.type	sysn32_call_table, @object
+EXPORT(sysn32_call_table)
+#include <asm/syscall_table_n32.h>
diff --git a/arch/mips/kernel/scall64-n64.S b/arch/mips/kernel/scall64-n64.S
new file mode 100644
index 000000000..e6264aa62
--- /dev/null
+++ b/arch/mips/kernel/scall64-n64.S
@@ -0,0 +1,115 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995, 96, 97, 98, 99, 2000, 01, 02 by Ralf Baechle
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ * Copyright (C) 2001 MIPS Technologies, Inc.
+ */
+#include <linux/errno.h>
+#include <asm/asm.h>
+#include <asm/asmmacro.h>
+#include <asm/irqflags.h>
+#include <asm/mipsregs.h>
+#include <asm/regdef.h>
+#include <asm/stackframe.h>
+#include <asm/asm-offsets.h>
+#include <asm/sysmips.h>
+#include <asm/thread_info.h>
+#include <asm/unistd.h>
+
+#ifndef CONFIG_MIPS32_COMPAT
+/* Neither O32 nor N32, so define handle_sys here */
+#define handle_sys64 handle_sys
+#endif
+
+	.align	5
+NESTED(handle_sys64, PT_SIZE, sp)
+#if !defined(CONFIG_MIPS32_O32) && !defined(CONFIG_MIPS32_N32)
+	/*
+	 * When 32-bit compatibility is configured scall_o32.S
+	 * already did this.
+	 */
+	.set	noat
+	SAVE_SOME
+	TRACE_IRQS_ON_RELOAD
+	STI
+	.set	at
+#endif
+
+#if !defined(CONFIG_MIPS32_O32) && !defined(CONFIG_MIPS32_N32)
+	ld	t1, PT_EPC(sp)		# skip syscall on return
+	daddiu	t1, 4			# skip to next instruction
+	sd	t1, PT_EPC(sp)
+#endif
+
+	sd	a3, PT_R26(sp)		# save a3 for syscall restarting
+
+	li	t1, _TIF_WORK_SYSCALL_ENTRY
+	LONG_L	t0, TI_FLAGS($28)	# syscall tracing enabled?
+	and	t0, t1, t0
+	bnez	t0, syscall_trace_entry
+
+syscall_common:
+	dsubu	t2, v0, __NR_64_Linux
+	sltiu   t0, t2, __NR_64_Linux_syscalls
+	beqz	t0, illegal_syscall
+
+	dsll	t0, t2, 3		# offset into table
+	dla	t2, sys_call_table
+	daddu	t0, t2, t0
+	ld	t2, (t0)		# syscall routine
+	beqz	t2, illegal_syscall
+
+	jalr	t2			# Do The Real Thing (TM)
+
+	li	t0, -EMAXERRNO - 1	# error?
+	sltu	t0, t0, v0
+	sd	t0, PT_R7(sp)		# set error flag
+	beqz	t0, 1f
+
+	ld	t1, PT_R2(sp)		# syscall number
+	dnegu	v0			# error
+	sd	t1, PT_R0(sp)		# save it for syscall restarting
+1:	sd	v0, PT_R2(sp)		# result
+
+n64_syscall_exit:
+	j	syscall_exit_partial
+
+/* ------------------------------------------------------------------------ */
+
+syscall_trace_entry:
+	SAVE_STATIC
+	move	a0, sp
+	move	a1, v0
+	jal	syscall_trace_enter
+
+	bltz	v0, 1f			# seccomp failed? Skip syscall
+
+	RESTORE_STATIC
+	ld	v0, PT_R2(sp)		# Restore syscall (maybe modified)
+	ld	a0, PT_R4(sp)		# Restore argument registers
+	ld	a1, PT_R5(sp)
+	ld	a2, PT_R6(sp)
+	ld	a3, PT_R7(sp)
+	ld	a4, PT_R8(sp)
+	ld	a5, PT_R9(sp)
+	j	syscall_common
+
+1:	j	syscall_exit
+
+illegal_syscall:
+	/* This also isn't a 64-bit syscall, throw an error.  */
+	li	v0, ENOSYS			# error
+	sd	v0, PT_R2(sp)
+	li	t0, 1				# set error flag
+	sd	t0, PT_R7(sp)
+	j	n64_syscall_exit
+	END(handle_sys64)
+
+#define __SYSCALL(nr, entry)	PTR_WD entry
+	.align	3
+	.type	sys_call_table, @object
+EXPORT(sys_call_table)
+#include <asm/syscall_table_n64.h>
diff --git a/arch/mips/kernel/scall64-o32.S b/arch/mips/kernel/scall64-o32.S
new file mode 100644
index 000000000..d3c2616cb
--- /dev/null
+++ b/arch/mips/kernel/scall64-o32.S
@@ -0,0 +1,221 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995 - 2000, 2001 by Ralf Baechle
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ * Copyright (C) 2001 MIPS Technologies, Inc.
+ * Copyright (C) 2004 Thiemo Seufer
+ *
+ * Hairy, the userspace application uses a different argument passing
+ * convention than the kernel, so we have to translate things from o32
+ * to ABI64 calling convention.	 64-bit syscalls are also processed
+ * here for now.
+ */
+#include <linux/errno.h>
+#include <asm/asm.h>
+#include <asm/asmmacro.h>
+#include <asm/irqflags.h>
+#include <asm/mipsregs.h>
+#include <asm/regdef.h>
+#include <asm/stackframe.h>
+#include <asm/thread_info.h>
+#include <asm/unistd.h>
+#include <asm/sysmips.h>
+
+	.align	5
+NESTED(handle_sys, PT_SIZE, sp)
+	.set	noat
+	SAVE_SOME
+	TRACE_IRQS_ON_RELOAD
+	STI
+	.set	at
+	ld	t1, PT_EPC(sp)		# skip syscall on return
+
+	dsubu	t0, v0, __NR_O32_Linux	# check syscall number
+	sltiu	t0, t0, __NR_O32_Linux_syscalls
+	daddiu	t1, 4			# skip to next instruction
+	sd	t1, PT_EPC(sp)
+	beqz	t0, not_o32_scall
+#if 0
+ SAVE_ALL
+ move a1, v0
+ ASM_PRINT("Scall %ld\n")
+ RESTORE_ALL
+#endif
+
+	/* We don't want to stumble over broken sign extensions from
+	   userland. O32 does never use the upper half. */
+	sll	a0, a0, 0
+	sll	a1, a1, 0
+	sll	a2, a2, 0
+	sll	a3, a3, 0
+
+	sd	a3, PT_R26(sp)		# save a3 for syscall restarting
+
+	/*
+	 * More than four arguments.  Try to deal with it by copying the
+	 * stack arguments from the user stack to the kernel stack.
+	 * This Sucks (TM).
+	 *
+	 * We intentionally keep the kernel stack a little below the top of
+	 * userspace so we don't have to do a slower byte accurate check here.
+	 */
+	ld	t0, PT_R29(sp)		# get old user stack pointer
+	daddu	t1, t0, 32
+	bltz	t1, bad_stack
+
+load_a4: lw	a4, 16(t0)		# argument #5 from usp
+load_a5: lw	a5, 20(t0)		# argument #6 from usp
+load_a6: lw	a6, 24(t0)		# argument #7 from usp
+load_a7: lw	a7, 28(t0)		# argument #8 from usp
+loads_done:
+
+	.section __ex_table,"a"
+	PTR_WD	load_a4, bad_stack_a4
+	PTR_WD	load_a5, bad_stack_a5
+	PTR_WD	load_a6, bad_stack_a6
+	PTR_WD	load_a7, bad_stack_a7
+	.previous
+
+	li	t1, _TIF_WORK_SYSCALL_ENTRY
+	LONG_L	t0, TI_FLAGS($28)	# syscall tracing enabled?
+	and	t0, t1, t0
+	bnez	t0, trace_a_syscall
+
+syscall_common:
+	dsll	t0, v0, 3		# offset into table
+	ld	t2, (sys32_call_table - (__NR_O32_Linux * 8))(t0)
+
+	jalr	t2			# Do The Real Thing (TM)
+
+	li	t0, -EMAXERRNO - 1	# error?
+	sltu	t0, t0, v0
+	sd	t0, PT_R7(sp)		# set error flag
+	beqz	t0, 1f
+
+	ld	t1, PT_R2(sp)		# syscall number
+	dnegu	v0			# error
+	sd	t1, PT_R0(sp)		# save it for syscall restarting
+1:	sd	v0, PT_R2(sp)		# result
+
+o32_syscall_exit:
+	j	syscall_exit_partial
+
+/* ------------------------------------------------------------------------ */
+
+trace_a_syscall:
+	SAVE_STATIC
+	sd	a4, PT_R8(sp)		# Save argument registers
+	sd	a5, PT_R9(sp)
+	sd	a6, PT_R10(sp)
+	sd	a7, PT_R11(sp)		# For indirect syscalls
+
+	move	a0, sp
+	/*
+	 * absolute syscall number is in v0 unless we called syscall(__NR_###)
+	 * where the real syscall number is in a0
+	 * note: NR_syscall is the first O32 syscall but the macro is
+	 * only defined when compiling with -mabi=32 (CONFIG_32BIT)
+	 * therefore __NR_O32_Linux is used (4000)
+	 */
+	.set	push
+	.set	reorder
+	subu	t1, v0,  __NR_O32_Linux
+	move	a1, v0
+	bnez	t1, 1f /* __NR_syscall at offset 0 */
+	ld	a1, PT_R4(sp) /* Arg1 for __NR_syscall case */
+	.set	pop
+
+1:	jal	syscall_trace_enter
+
+	bltz	v0, 1f			# seccomp failed? Skip syscall
+
+	RESTORE_STATIC
+	ld	v0, PT_R2(sp)		# Restore syscall (maybe modified)
+	ld	a0, PT_R4(sp)		# Restore argument registers
+	ld	a1, PT_R5(sp)
+	ld	a2, PT_R6(sp)
+	ld	a3, PT_R7(sp)
+	ld	a4, PT_R8(sp)
+	ld	a5, PT_R9(sp)
+	ld	a6, PT_R10(sp)
+	ld	a7, PT_R11(sp)		# For indirect syscalls
+
+	dsubu	t0, v0, __NR_O32_Linux	# check (new) syscall number
+	sltiu	t0, t0, __NR_O32_Linux_syscalls
+	beqz	t0, not_o32_scall
+
+	j	syscall_common
+
+1:	j	syscall_exit
+
+/* ------------------------------------------------------------------------ */
+
+	/*
+	 * The stackpointer for a call with more than 4 arguments is bad.
+	 */
+bad_stack:
+	li	v0, EFAULT
+	sd	v0, PT_R2(sp)
+	li	t0, 1			# set error flag
+	sd	t0, PT_R7(sp)
+	j	o32_syscall_exit
+
+bad_stack_a4:
+	li	a4, 0
+	b	load_a5
+
+bad_stack_a5:
+	li	a5, 0
+	b	load_a6
+
+bad_stack_a6:
+	li	a6, 0
+	b	load_a7
+
+bad_stack_a7:
+	li	a7, 0
+	b	loads_done
+
+not_o32_scall:
+	/*
+	 * This is not an o32 compatibility syscall, pass it on
+	 * to the 64-bit syscall handlers.
+	 */
+#ifdef CONFIG_MIPS32_N32
+	j	handle_sysn32
+#else
+	j	handle_sys64
+#endif
+	END(handle_sys)
+
+LEAF(sys32_syscall)
+	subu	t0, a0, __NR_O32_Linux	# check syscall number
+	sltiu	v0, t0, __NR_O32_Linux_syscalls
+	beqz	t0, einval		# do not recurse
+	dsll	t1, t0, 3
+	beqz	v0, einval
+	ld	t2, sys32_call_table(t1)		# syscall routine
+
+	move	a0, a1			# shift argument registers
+	move	a1, a2
+	move	a2, a3
+	move	a3, a4
+	move	a4, a5
+	move	a5, a6
+	move	a6, a7
+	jr	t2
+	/* Unreached */
+
+einval: li	v0, -ENOSYS
+	jr	ra
+	END(sys32_syscall)
+
+#define __SYSCALL_WITH_COMPAT(nr, native, compat)	__SYSCALL(nr, compat)
+#define __SYSCALL(nr, entry)	PTR_WD entry
+	.align	3
+	.type	sys32_call_table,@object
+EXPORT(sys32_call_table)
+#include <asm/syscall_table_o32.h>
diff --git a/arch/mips/kernel/segment.c b/arch/mips/kernel/segment.c
new file mode 100644
index 000000000..24560501c
--- /dev/null
+++ b/arch/mips/kernel/segment.c
@@ -0,0 +1,93 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2013 Imagination Technologies Ltd.
+ */
+
+#include <linux/kernel.h>
+#include <linux/debugfs.h>
+#include <linux/seq_file.h>
+#include <asm/cpu.h>
+#include <asm/debug.h>
+#include <asm/mipsregs.h>
+
+static void build_segment_config(char *str, unsigned int cfg)
+{
+	unsigned int am;
+	static const char * const am_str[] = {
+		"UK", "MK", "MSK", "MUSK", "MUSUK", "USK",
+		"RSRVD", "UUSK"};
+
+	/* Segment access mode. */
+	am = (cfg & MIPS_SEGCFG_AM) >> MIPS_SEGCFG_AM_SHIFT;
+	str += sprintf(str, "%-5s", am_str[am]);
+
+	/*
+	 * Access modes MK, MSK and MUSK are mapped segments. Therefore
+	 * there is no direct physical address mapping unless it becomes
+	 * unmapped uncached at error level due to EU.
+	 */
+	if ((am == 0) || (am > 3) || (cfg & MIPS_SEGCFG_EU))
+		str += sprintf(str, "         %03lx",
+			((cfg & MIPS_SEGCFG_PA) >> MIPS_SEGCFG_PA_SHIFT));
+	else
+		str += sprintf(str, "         UND");
+
+	if ((am == 0) || (am > 3))
+		str += sprintf(str, "         %01ld",
+			((cfg & MIPS_SEGCFG_C) >> MIPS_SEGCFG_C_SHIFT));
+	else
+		str += sprintf(str, "         U");
+
+	/* Exception configuration. */
+	str += sprintf(str, "       %01ld\n",
+		((cfg & MIPS_SEGCFG_EU) >> MIPS_SEGCFG_EU_SHIFT));
+}
+
+static int segments_show(struct seq_file *m, void *v)
+{
+	unsigned int segcfg;
+	char str[42];
+
+	seq_puts(m, "Segment   Virtual    Size   Access Mode   Physical   Caching   EU\n");
+	seq_puts(m, "-------   -------    ----   -----------   --------   -------   --\n");
+
+	segcfg = read_c0_segctl0();
+	build_segment_config(str, segcfg);
+	seq_printf(m, "   0      e0000000   512M      %s", str);
+
+	segcfg >>= 16;
+	build_segment_config(str, segcfg);
+	seq_printf(m, "   1      c0000000   512M      %s", str);
+
+	segcfg = read_c0_segctl1();
+	build_segment_config(str, segcfg);
+	seq_printf(m, "   2      a0000000   512M      %s", str);
+
+	segcfg >>= 16;
+	build_segment_config(str, segcfg);
+	seq_printf(m, "   3      80000000   512M      %s", str);
+
+	segcfg = read_c0_segctl2();
+	build_segment_config(str, segcfg);
+	seq_printf(m, "   4      40000000    1G       %s", str);
+
+	segcfg >>= 16;
+	build_segment_config(str, segcfg);
+	seq_printf(m, "   5      00000000    1G       %s\n", str);
+
+	return 0;
+}
+DEFINE_SHOW_ATTRIBUTE(segments);
+
+static int __init segments_info(void)
+{
+	if (cpu_has_segments)
+		debugfs_create_file("segments", S_IRUGO, mips_debugfs_dir, NULL,
+				    &segments_fops);
+	return 0;
+}
+
+device_initcall(segments_info);
diff --git a/arch/mips/kernel/setup.c b/arch/mips/kernel/setup.c
new file mode 100644
index 000000000..e46e7ec76
--- /dev/null
+++ b/arch/mips/kernel/setup.c
@@ -0,0 +1,855 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995 Linus Torvalds
+ * Copyright (C) 1995 Waldorf Electronics
+ * Copyright (C) 1994, 95, 96, 97, 98, 99, 2000, 01, 02, 03  Ralf Baechle
+ * Copyright (C) 1996 Stoned Elipot
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ * Copyright (C) 2000, 2001, 2002, 2007	 Maciej W. Rozycki
+ */
+#include <linux/init.h>
+#include <linux/cpu.h>
+#include <linux/delay.h>
+#include <linux/ioport.h>
+#include <linux/export.h>
+#include <linux/screen_info.h>
+#include <linux/memblock.h>
+#include <linux/initrd.h>
+#include <linux/root_dev.h>
+#include <linux/highmem.h>
+#include <linux/console.h>
+#include <linux/pfn.h>
+#include <linux/debugfs.h>
+#include <linux/kexec.h>
+#include <linux/sizes.h>
+#include <linux/device.h>
+#include <linux/dma-map-ops.h>
+#include <linux/decompress/generic.h>
+#include <linux/of_fdt.h>
+#include <linux/dmi.h>
+#include <linux/crash_dump.h>
+
+#include <asm/addrspace.h>
+#include <asm/bootinfo.h>
+#include <asm/bugs.h>
+#include <asm/cache.h>
+#include <asm/cdmm.h>
+#include <asm/cpu.h>
+#include <asm/debug.h>
+#include <asm/mmzone.h>
+#include <asm/sections.h>
+#include <asm/setup.h>
+#include <asm/smp-ops.h>
+#include <asm/prom.h>
+#include <asm/fw/fw.h>
+
+#ifdef CONFIG_MIPS_ELF_APPENDED_DTB
+char __section(".appended_dtb") __appended_dtb[0x100000];
+#endif /* CONFIG_MIPS_ELF_APPENDED_DTB */
+
+struct cpuinfo_mips cpu_data[NR_CPUS] __read_mostly;
+
+EXPORT_SYMBOL(cpu_data);
+
+#ifdef CONFIG_VT
+struct screen_info screen_info;
+#endif
+
+/*
+ * Setup information
+ *
+ * These are initialized so they are in the .data section
+ */
+unsigned long mips_machtype __read_mostly = MACH_UNKNOWN;
+
+EXPORT_SYMBOL(mips_machtype);
+
+static char __initdata command_line[COMMAND_LINE_SIZE];
+char __initdata arcs_cmdline[COMMAND_LINE_SIZE];
+
+#ifdef CONFIG_CMDLINE_BOOL
+static const char builtin_cmdline[] __initconst = CONFIG_CMDLINE;
+#else
+static const char builtin_cmdline[] __initconst = "";
+#endif
+
+/*
+ * mips_io_port_base is the begin of the address space to which x86 style
+ * I/O ports are mapped.
+ */
+unsigned long mips_io_port_base = -1;
+EXPORT_SYMBOL(mips_io_port_base);
+
+static struct resource code_resource = { .name = "Kernel code", };
+static struct resource data_resource = { .name = "Kernel data", };
+static struct resource bss_resource = { .name = "Kernel bss", };
+
+unsigned long __kaslr_offset __ro_after_init;
+EXPORT_SYMBOL(__kaslr_offset);
+
+static void *detect_magic __initdata = detect_memory_region;
+
+#ifdef CONFIG_MIPS_AUTO_PFN_OFFSET
+unsigned long ARCH_PFN_OFFSET;
+EXPORT_SYMBOL(ARCH_PFN_OFFSET);
+#endif
+
+void __init detect_memory_region(phys_addr_t start, phys_addr_t sz_min, phys_addr_t sz_max)
+{
+	void *dm = &detect_magic;
+	phys_addr_t size;
+
+	for (size = sz_min; size < sz_max; size <<= 1) {
+		if (!memcmp(dm, dm + size, sizeof(detect_magic)))
+			break;
+	}
+
+	pr_debug("Memory: %lluMB of RAM detected at 0x%llx (min: %lluMB, max: %lluMB)\n",
+		((unsigned long long) size) / SZ_1M,
+		(unsigned long long) start,
+		((unsigned long long) sz_min) / SZ_1M,
+		((unsigned long long) sz_max) / SZ_1M);
+
+	memblock_add(start, size);
+}
+
+/*
+ * Manage initrd
+ */
+#ifdef CONFIG_BLK_DEV_INITRD
+
+static int __init rd_start_early(char *p)
+{
+	unsigned long start = memparse(p, &p);
+
+#ifdef CONFIG_64BIT
+	/* Guess if the sign extension was forgotten by bootloader */
+	if (start < XKPHYS)
+		start = (int)start;
+#endif
+	initrd_start = start;
+	initrd_end += start;
+	return 0;
+}
+early_param("rd_start", rd_start_early);
+
+static int __init rd_size_early(char *p)
+{
+	initrd_end += memparse(p, &p);
+	return 0;
+}
+early_param("rd_size", rd_size_early);
+
+/* it returns the next free pfn after initrd */
+static unsigned long __init init_initrd(void)
+{
+	unsigned long end;
+
+	/*
+	 * Board specific code or command line parser should have
+	 * already set up initrd_start and initrd_end. In these cases
+	 * perfom sanity checks and use them if all looks good.
+	 */
+	if (!initrd_start || initrd_end <= initrd_start)
+		goto disable;
+
+	if (initrd_start & ~PAGE_MASK) {
+		pr_err("initrd start must be page aligned\n");
+		goto disable;
+	}
+
+	/*
+	 * Sanitize initrd addresses. For example firmware
+	 * can't guess if they need to pass them through
+	 * 64-bits values if the kernel has been built in pure
+	 * 32-bit. We need also to switch from KSEG0 to XKPHYS
+	 * addresses now, so the code can now safely use __pa().
+	 */
+	end = __pa(initrd_end);
+	initrd_end = (unsigned long)__va(end);
+	initrd_start = (unsigned long)__va(__pa(initrd_start));
+
+	if (initrd_start < PAGE_OFFSET) {
+		pr_err("initrd start < PAGE_OFFSET\n");
+		goto disable;
+	}
+
+	ROOT_DEV = Root_RAM0;
+	return PFN_UP(end);
+disable:
+	initrd_start = 0;
+	initrd_end = 0;
+	return 0;
+}
+
+/* In some conditions (e.g. big endian bootloader with a little endian
+   kernel), the initrd might appear byte swapped.  Try to detect this and
+   byte swap it if needed.  */
+static void __init maybe_bswap_initrd(void)
+{
+#if defined(CONFIG_CPU_CAVIUM_OCTEON)
+	u64 buf;
+
+	/* Check for CPIO signature */
+	if (!memcmp((void *)initrd_start, "070701", 6))
+		return;
+
+	/* Check for compressed initrd */
+	if (decompress_method((unsigned char *)initrd_start, 8, NULL))
+		return;
+
+	/* Try again with a byte swapped header */
+	buf = swab64p((u64 *)initrd_start);
+	if (!memcmp(&buf, "070701", 6) ||
+	    decompress_method((unsigned char *)(&buf), 8, NULL)) {
+		unsigned long i;
+
+		pr_info("Byteswapped initrd detected\n");
+		for (i = initrd_start; i < ALIGN(initrd_end, 8); i += 8)
+			swab64s((u64 *)i);
+	}
+#endif
+}
+
+static void __init finalize_initrd(void)
+{
+	unsigned long size = initrd_end - initrd_start;
+
+	if (size == 0) {
+		printk(KERN_INFO "Initrd not found or empty");
+		goto disable;
+	}
+	if (__pa(initrd_end) > PFN_PHYS(max_low_pfn)) {
+		printk(KERN_ERR "Initrd extends beyond end of memory");
+		goto disable;
+	}
+
+	maybe_bswap_initrd();
+
+	memblock_reserve(__pa(initrd_start), size);
+	initrd_below_start_ok = 1;
+
+	pr_info("Initial ramdisk at: 0x%lx (%lu bytes)\n",
+		initrd_start, size);
+	return;
+disable:
+	printk(KERN_CONT " - disabling initrd\n");
+	initrd_start = 0;
+	initrd_end = 0;
+}
+
+#else  /* !CONFIG_BLK_DEV_INITRD */
+
+static unsigned long __init init_initrd(void)
+{
+	return 0;
+}
+
+#define finalize_initrd()	do {} while (0)
+
+#endif
+
+/*
+ * Initialize the bootmem allocator. It also setup initrd related data
+ * if needed.
+ */
+#if defined(CONFIG_SGI_IP27) || (defined(CONFIG_CPU_LOONGSON64) && defined(CONFIG_NUMA))
+
+static void __init bootmem_init(void)
+{
+	init_initrd();
+	finalize_initrd();
+}
+
+#else  /* !CONFIG_SGI_IP27 */
+
+static void __init bootmem_init(void)
+{
+	phys_addr_t ramstart, ramend;
+	unsigned long start, end;
+	int i;
+
+	ramstart = memblock_start_of_DRAM();
+	ramend = memblock_end_of_DRAM();
+
+	/*
+	 * Sanity check any INITRD first. We don't take it into account
+	 * for bootmem setup initially, rely on the end-of-kernel-code
+	 * as our memory range starting point. Once bootmem is inited we
+	 * will reserve the area used for the initrd.
+	 */
+	init_initrd();
+
+	/* Reserve memory occupied by kernel. */
+	memblock_reserve(__pa_symbol(&_text),
+			__pa_symbol(&_end) - __pa_symbol(&_text));
+
+	/* max_low_pfn is not a number of pages but the end pfn of low mem */
+
+#ifdef CONFIG_MIPS_AUTO_PFN_OFFSET
+	ARCH_PFN_OFFSET = PFN_UP(ramstart);
+#else
+	/*
+	 * Reserve any memory between the start of RAM and PHYS_OFFSET
+	 */
+	if (ramstart > PHYS_OFFSET)
+		memblock_reserve(PHYS_OFFSET, ramstart - PHYS_OFFSET);
+
+	if (PFN_UP(ramstart) > ARCH_PFN_OFFSET) {
+		pr_info("Wasting %lu bytes for tracking %lu unused pages\n",
+			(unsigned long)((PFN_UP(ramstart) - ARCH_PFN_OFFSET) * sizeof(struct page)),
+			(unsigned long)(PFN_UP(ramstart) - ARCH_PFN_OFFSET));
+	}
+#endif
+
+	min_low_pfn = ARCH_PFN_OFFSET;
+	max_pfn = PFN_DOWN(ramend);
+	for_each_mem_pfn_range(i, MAX_NUMNODES, &start, &end, NULL) {
+		/*
+		 * Skip highmem here so we get an accurate max_low_pfn if low
+		 * memory stops short of high memory.
+		 * If the region overlaps HIGHMEM_START, end is clipped so
+		 * max_pfn excludes the highmem portion.
+		 */
+		if (start >= PFN_DOWN(HIGHMEM_START))
+			continue;
+		if (end > PFN_DOWN(HIGHMEM_START))
+			end = PFN_DOWN(HIGHMEM_START);
+		if (end > max_low_pfn)
+			max_low_pfn = end;
+	}
+
+	if (min_low_pfn >= max_low_pfn)
+		panic("Incorrect memory mapping !!!");
+
+	if (max_pfn > PFN_DOWN(HIGHMEM_START)) {
+		max_low_pfn = PFN_DOWN(HIGHMEM_START);
+#ifdef CONFIG_HIGHMEM
+		highstart_pfn = max_low_pfn;
+		highend_pfn = max_pfn;
+#else
+		max_pfn = max_low_pfn;
+#endif
+	}
+
+	/*
+	 * Reserve initrd memory if needed.
+	 */
+	finalize_initrd();
+}
+
+#endif	/* CONFIG_SGI_IP27 */
+
+static int usermem __initdata;
+
+static int __init early_parse_mem(char *p)
+{
+	phys_addr_t start, size;
+
+	if (!p) {
+		pr_err("mem parameter is empty, do nothing\n");
+		return -EINVAL;
+	}
+
+	/*
+	 * If a user specifies memory size, we
+	 * blow away any automatically generated
+	 * size.
+	 */
+	if (usermem == 0) {
+		usermem = 1;
+		memblock_remove(memblock_start_of_DRAM(),
+			memblock_end_of_DRAM() - memblock_start_of_DRAM());
+	}
+	start = 0;
+	size = memparse(p, &p);
+	if (*p == '@')
+		start = memparse(p + 1, &p);
+
+	if (IS_ENABLED(CONFIG_NUMA))
+		memblock_add_node(start, size, pa_to_nid(start), MEMBLOCK_NONE);
+	else
+		memblock_add(start, size);
+
+	return 0;
+}
+early_param("mem", early_parse_mem);
+
+static int __init early_parse_memmap(char *p)
+{
+	char *oldp;
+	u64 start_at, mem_size;
+
+	if (!p)
+		return -EINVAL;
+
+	if (!strncmp(p, "exactmap", 8)) {
+		pr_err("\"memmap=exactmap\" invalid on MIPS\n");
+		return 0;
+	}
+
+	oldp = p;
+	mem_size = memparse(p, &p);
+	if (p == oldp)
+		return -EINVAL;
+
+	if (*p == '@') {
+		start_at = memparse(p+1, &p);
+		memblock_add(start_at, mem_size);
+	} else if (*p == '#') {
+		pr_err("\"memmap=nn#ss\" (force ACPI data) invalid on MIPS\n");
+		return -EINVAL;
+	} else if (*p == '$') {
+		start_at = memparse(p+1, &p);
+		memblock_add(start_at, mem_size);
+		memblock_reserve(start_at, mem_size);
+	} else {
+		pr_err("\"memmap\" invalid format!\n");
+		return -EINVAL;
+	}
+
+	if (*p == '\0') {
+		usermem = 1;
+		return 0;
+	} else
+		return -EINVAL;
+}
+early_param("memmap", early_parse_memmap);
+
+static void __init mips_reserve_vmcore(void)
+{
+#ifdef CONFIG_PROC_VMCORE
+	phys_addr_t start, end;
+	u64 i;
+
+	if (!elfcorehdr_size) {
+		for_each_mem_range(i, &start, &end) {
+			if (elfcorehdr_addr >= start && elfcorehdr_addr < end) {
+				/*
+				 * Reserve from the elf core header to the end of
+				 * the memory segment, that should all be kdump
+				 * reserved memory.
+				 */
+				elfcorehdr_size = end - elfcorehdr_addr;
+				break;
+			}
+		}
+	}
+
+	pr_info("Reserving %ldKB of memory at %ldKB for kdump\n",
+		(unsigned long)elfcorehdr_size >> 10, (unsigned long)elfcorehdr_addr >> 10);
+
+	memblock_reserve(elfcorehdr_addr, elfcorehdr_size);
+#endif
+}
+
+#ifdef CONFIG_KEXEC
+
+/* 64M alignment for crash kernel regions */
+#define CRASH_ALIGN	SZ_64M
+#define CRASH_ADDR_MAX	SZ_512M
+
+static void __init mips_parse_crashkernel(void)
+{
+	unsigned long long total_mem;
+	unsigned long long crash_size, crash_base;
+	int ret;
+
+	total_mem = memblock_phys_mem_size();
+	ret = parse_crashkernel(boot_command_line, total_mem,
+				&crash_size, &crash_base);
+	if (ret != 0 || crash_size <= 0)
+		return;
+
+	if (crash_base <= 0) {
+		crash_base = memblock_phys_alloc_range(crash_size, CRASH_ALIGN,
+						       CRASH_ALIGN,
+						       CRASH_ADDR_MAX);
+		if (!crash_base) {
+			pr_warn("crashkernel reservation failed - No suitable area found.\n");
+			return;
+		}
+	} else {
+		unsigned long long start;
+
+		start = memblock_phys_alloc_range(crash_size, 1,
+						  crash_base,
+						  crash_base + crash_size);
+		if (start != crash_base) {
+			pr_warn("Invalid memory region reserved for crash kernel\n");
+			return;
+		}
+	}
+
+	crashk_res.start = crash_base;
+	crashk_res.end	 = crash_base + crash_size - 1;
+}
+
+static void __init request_crashkernel(struct resource *res)
+{
+	int ret;
+
+	if (crashk_res.start == crashk_res.end)
+		return;
+
+	ret = request_resource(res, &crashk_res);
+	if (!ret)
+		pr_info("Reserving %ldMB of memory at %ldMB for crashkernel\n",
+			(unsigned long)(resource_size(&crashk_res) >> 20),
+			(unsigned long)(crashk_res.start  >> 20));
+}
+#else /* !defined(CONFIG_KEXEC)		*/
+static void __init mips_parse_crashkernel(void)
+{
+}
+
+static void __init request_crashkernel(struct resource *res)
+{
+}
+#endif /* !defined(CONFIG_KEXEC)  */
+
+static void __init check_kernel_sections_mem(void)
+{
+	phys_addr_t start = __pa_symbol(&_text);
+	phys_addr_t size = __pa_symbol(&_end) - start;
+
+	if (!memblock_is_region_memory(start, size)) {
+		pr_info("Kernel sections are not in the memory maps\n");
+		memblock_add(start, size);
+	}
+}
+
+static void __init bootcmdline_append(const char *s, size_t max)
+{
+	if (!s[0] || !max)
+		return;
+
+	if (boot_command_line[0])
+		strlcat(boot_command_line, " ", COMMAND_LINE_SIZE);
+
+	strlcat(boot_command_line, s, max);
+}
+
+#ifdef CONFIG_OF_EARLY_FLATTREE
+
+static int __init bootcmdline_scan_chosen(unsigned long node, const char *uname,
+					  int depth, void *data)
+{
+	bool *dt_bootargs = data;
+	const char *p;
+	int l;
+
+	if (depth != 1 || !data ||
+	    (strcmp(uname, "chosen") != 0 && strcmp(uname, "chosen@0") != 0))
+		return 0;
+
+	p = of_get_flat_dt_prop(node, "bootargs", &l);
+	if (p != NULL && l > 0) {
+		bootcmdline_append(p, min(l, COMMAND_LINE_SIZE));
+		*dt_bootargs = true;
+	}
+
+	return 1;
+}
+
+#endif /* CONFIG_OF_EARLY_FLATTREE */
+
+static void __init bootcmdline_init(void)
+{
+	bool dt_bootargs = false;
+
+	/*
+	 * If CMDLINE_OVERRIDE is enabled then initializing the command line is
+	 * trivial - we simply use the built-in command line unconditionally &
+	 * unmodified.
+	 */
+	if (IS_ENABLED(CONFIG_CMDLINE_OVERRIDE)) {
+		strscpy(boot_command_line, builtin_cmdline, COMMAND_LINE_SIZE);
+		return;
+	}
+
+	/*
+	 * If the user specified a built-in command line &
+	 * MIPS_CMDLINE_BUILTIN_EXTEND, then the built-in command line is
+	 * prepended to arguments from the bootloader or DT so we'll copy them
+	 * to the start of boot_command_line here. Otherwise, empty
+	 * boot_command_line to undo anything early_init_dt_scan_chosen() did.
+	 */
+	if (IS_ENABLED(CONFIG_MIPS_CMDLINE_BUILTIN_EXTEND))
+		strscpy(boot_command_line, builtin_cmdline, COMMAND_LINE_SIZE);
+	else
+		boot_command_line[0] = 0;
+
+#ifdef CONFIG_OF_EARLY_FLATTREE
+	/*
+	 * If we're configured to take boot arguments from DT, look for those
+	 * now.
+	 */
+	if (IS_ENABLED(CONFIG_MIPS_CMDLINE_FROM_DTB) ||
+	    IS_ENABLED(CONFIG_MIPS_CMDLINE_DTB_EXTEND))
+		of_scan_flat_dt(bootcmdline_scan_chosen, &dt_bootargs);
+#endif
+
+	/*
+	 * If we didn't get any arguments from DT (regardless of whether that's
+	 * because we weren't configured to look for them, or because we looked
+	 * & found none) then we'll take arguments from the bootloader.
+	 * plat_mem_setup() should have filled arcs_cmdline with arguments from
+	 * the bootloader.
+	 */
+	if (IS_ENABLED(CONFIG_MIPS_CMDLINE_DTB_EXTEND) || !dt_bootargs)
+		bootcmdline_append(arcs_cmdline, COMMAND_LINE_SIZE);
+
+	/*
+	 * If the user specified a built-in command line & we didn't already
+	 * prepend it, we append it to boot_command_line here.
+	 */
+	if (IS_ENABLED(CONFIG_CMDLINE_BOOL) &&
+	    !IS_ENABLED(CONFIG_MIPS_CMDLINE_BUILTIN_EXTEND))
+		bootcmdline_append(builtin_cmdline, COMMAND_LINE_SIZE);
+}
+
+/*
+ * arch_mem_init - initialize memory management subsystem
+ *
+ *  o plat_mem_setup() detects the memory configuration and will record detected
+ *    memory areas using memblock_add.
+ *
+ * At this stage the memory configuration of the system is known to the
+ * kernel but generic memory management system is still entirely uninitialized.
+ *
+ *  o bootmem_init()
+ *  o sparse_init()
+ *  o paging_init()
+ *  o dma_contiguous_reserve()
+ *
+ * At this stage the bootmem allocator is ready to use.
+ *
+ * NOTE: historically plat_mem_setup did the entire platform initialization.
+ *	 This was rather impractical because it meant plat_mem_setup had to
+ * get away without any kind of memory allocator.  To keep old code from
+ * breaking plat_setup was just renamed to plat_mem_setup and a second platform
+ * initialization hook for anything else was introduced.
+ */
+static void __init arch_mem_init(char **cmdline_p)
+{
+	/* call board setup routine */
+	plat_mem_setup();
+	memblock_set_bottom_up(true);
+
+	bootcmdline_init();
+	strscpy(command_line, boot_command_line, COMMAND_LINE_SIZE);
+	*cmdline_p = command_line;
+
+	parse_early_param();
+
+	if (usermem)
+		pr_info("User-defined physical RAM map overwrite\n");
+
+	check_kernel_sections_mem();
+
+	early_init_fdt_reserve_self();
+	early_init_fdt_scan_reserved_mem();
+
+#ifndef CONFIG_NUMA
+	memblock_set_node(0, PHYS_ADDR_MAX, &memblock.memory, 0);
+#endif
+	bootmem_init();
+
+	/*
+	 * Prevent memblock from allocating high memory.
+	 * This cannot be done before max_low_pfn is detected, so up
+	 * to this point is possible to only reserve physical memory
+	 * with memblock_reserve; memblock_alloc* can be used
+	 * only after this point
+	 */
+	memblock_set_current_limit(PFN_PHYS(max_low_pfn));
+
+	mips_reserve_vmcore();
+
+	mips_parse_crashkernel();
+	device_tree_init();
+
+	/*
+	 * In order to reduce the possibility of kernel panic when failed to
+	 * get IO TLB memory under CONFIG_SWIOTLB, it is better to allocate
+	 * low memory as small as possible before plat_swiotlb_setup(), so
+	 * make sparse_init() using top-down allocation.
+	 */
+	memblock_set_bottom_up(false);
+	sparse_init();
+	memblock_set_bottom_up(true);
+
+	plat_swiotlb_setup();
+
+	dma_contiguous_reserve(PFN_PHYS(max_low_pfn));
+
+	/* Reserve for hibernation. */
+	memblock_reserve(__pa_symbol(&__nosave_begin),
+		__pa_symbol(&__nosave_end) - __pa_symbol(&__nosave_begin));
+
+	early_memtest(PFN_PHYS(ARCH_PFN_OFFSET), PFN_PHYS(max_low_pfn));
+}
+
+static void __init resource_init(void)
+{
+	phys_addr_t start, end;
+	u64 i;
+
+	if (UNCAC_BASE != IO_BASE)
+		return;
+
+	code_resource.start = __pa_symbol(&_text);
+	code_resource.end = __pa_symbol(&_etext) - 1;
+	data_resource.start = __pa_symbol(&_etext);
+	data_resource.end = __pa_symbol(&_edata) - 1;
+	bss_resource.start = __pa_symbol(&__bss_start);
+	bss_resource.end = __pa_symbol(&__bss_stop) - 1;
+
+	for_each_mem_range(i, &start, &end) {
+		struct resource *res;
+
+		res = memblock_alloc(sizeof(struct resource), SMP_CACHE_BYTES);
+		if (!res)
+			panic("%s: Failed to allocate %zu bytes\n", __func__,
+			      sizeof(struct resource));
+
+		res->start = start;
+		/*
+		 * In memblock, end points to the first byte after the
+		 * range while in resourses, end points to the last byte in
+		 * the range.
+		 */
+		res->end = end - 1;
+		res->flags = IORESOURCE_SYSTEM_RAM | IORESOURCE_BUSY;
+		res->name = "System RAM";
+
+		request_resource(&iomem_resource, res);
+
+		/*
+		 *  We don't know which RAM region contains kernel data,
+		 *  so we try it repeatedly and let the resource manager
+		 *  test it.
+		 */
+		request_resource(res, &code_resource);
+		request_resource(res, &data_resource);
+		request_resource(res, &bss_resource);
+		request_crashkernel(res);
+	}
+}
+
+#ifdef CONFIG_SMP
+static void __init prefill_possible_map(void)
+{
+	int i, possible = num_possible_cpus();
+
+	if (possible > nr_cpu_ids)
+		possible = nr_cpu_ids;
+
+	for (i = 0; i < possible; i++)
+		set_cpu_possible(i, true);
+	for (; i < NR_CPUS; i++)
+		set_cpu_possible(i, false);
+
+	set_nr_cpu_ids(possible);
+}
+#else
+static inline void prefill_possible_map(void) {}
+#endif
+
+static void __init setup_rng_seed(void)
+{
+	char *rng_seed_hex = fw_getenv("rngseed");
+	u8 rng_seed[512];
+	size_t len;
+
+	if (!rng_seed_hex)
+		return;
+
+	len = min(sizeof(rng_seed), strlen(rng_seed_hex) / 2);
+	if (hex2bin(rng_seed, rng_seed_hex, len))
+		return;
+
+	add_bootloader_randomness(rng_seed, len);
+	memzero_explicit(rng_seed, len);
+	memzero_explicit(rng_seed_hex, len * 2);
+}
+
+void __init setup_arch(char **cmdline_p)
+{
+	cpu_probe();
+	mips_cm_probe();
+	prom_init();
+
+	setup_early_fdc_console();
+#ifdef CONFIG_EARLY_PRINTK
+	setup_early_printk();
+#endif
+	cpu_report();
+	check_bugs_early();
+
+#if defined(CONFIG_VT)
+#if defined(CONFIG_VGA_CONSOLE)
+	conswitchp = &vga_con;
+#endif
+#endif
+
+	arch_mem_init(cmdline_p);
+	dmi_setup();
+
+	resource_init();
+	plat_smp_setup();
+	prefill_possible_map();
+
+	cpu_cache_init();
+	paging_init();
+
+	memblock_dump_all();
+
+	setup_rng_seed();
+}
+
+unsigned long kernelsp[NR_CPUS];
+unsigned long fw_arg0, fw_arg1, fw_arg2, fw_arg3;
+
+#ifdef CONFIG_DEBUG_FS
+struct dentry *mips_debugfs_dir;
+static int __init debugfs_mips(void)
+{
+	mips_debugfs_dir = debugfs_create_dir("mips", NULL);
+	return 0;
+}
+arch_initcall(debugfs_mips);
+#endif
+
+#ifdef CONFIG_DMA_NONCOHERENT
+static int __init setcoherentio(char *str)
+{
+	dma_default_coherent = true;
+	pr_info("Hardware DMA cache coherency (command line)\n");
+	return 0;
+}
+early_param("coherentio", setcoherentio);
+
+static int __init setnocoherentio(char *str)
+{
+	dma_default_coherent = false;
+	pr_info("Software DMA cache coherency (command line)\n");
+	return 0;
+}
+early_param("nocoherentio", setnocoherentio);
+#endif
+
+void __init arch_cpu_finalize_init(void)
+{
+	unsigned int cpu = smp_processor_id();
+
+	cpu_data[cpu].udelay_val = loops_per_jiffy;
+	check_bugs32();
+
+	if (IS_ENABLED(CONFIG_CPU_R4X00_BUGS64))
+		check_bugs64();
+}
diff --git a/arch/mips/kernel/signal-common.h b/arch/mips/kernel/signal-common.h
new file mode 100644
index 000000000..f50d48435
--- /dev/null
+++ b/arch/mips/kernel/signal-common.h
@@ -0,0 +1,43 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1991, 1992  Linus Torvalds
+ * Copyright (C) 1994 - 2000  Ralf Baechle
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ */
+
+#ifndef __SIGNAL_COMMON_H
+#define __SIGNAL_COMMON_H
+
+/* #define DEBUG_SIG */
+
+#ifdef DEBUG_SIG
+#  define DEBUGP(fmt, args...) printk("%s: " fmt, __func__, ##args)
+#else
+#  define DEBUGP(fmt, args...)
+#endif
+
+/*
+ * Determine which stack to use..
+ */
+extern void __user *get_sigframe(struct ksignal *ksig, struct pt_regs *regs,
+				 size_t frame_size);
+/* Check and clear pending FPU exceptions in saved CSR */
+extern int fpcsr_pending(unsigned int __user *fpcsr);
+
+/* Make sure we will not lose FPU ownership */
+#define lock_fpu_owner()	({ preempt_disable(); pagefault_disable(); })
+#define unlock_fpu_owner()	({ pagefault_enable(); preempt_enable(); })
+
+/* Assembly functions to move context to/from the FPU */
+extern asmlinkage int
+_save_fp_context(void __user *fpregs, void __user *csr);
+extern asmlinkage int
+_restore_fp_context(void __user *fpregs, void __user *csr);
+
+extern asmlinkage int _save_msa_all_upper(void __user *buf);
+extern asmlinkage int _restore_msa_all_upper(void __user *buf);
+
+#endif	/* __SIGNAL_COMMON_H */
diff --git a/arch/mips/kernel/signal.c b/arch/mips/kernel/signal.c
new file mode 100644
index 000000000..479999b7f
--- /dev/null
+++ b/arch/mips/kernel/signal.c
@@ -0,0 +1,968 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1991, 1992  Linus Torvalds
+ * Copyright (C) 1994 - 2000  Ralf Baechle
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ * Copyright (C) 2014, Imagination Technologies Ltd.
+ */
+#include <linux/cache.h>
+#include <linux/context_tracking.h>
+#include <linux/irqflags.h>
+#include <linux/sched.h>
+#include <linux/mm.h>
+#include <linux/personality.h>
+#include <linux/smp.h>
+#include <linux/kernel.h>
+#include <linux/signal.h>
+#include <linux/errno.h>
+#include <linux/wait.h>
+#include <linux/ptrace.h>
+#include <linux/unistd.h>
+#include <linux/uprobes.h>
+#include <linux/compiler.h>
+#include <linux/syscalls.h>
+#include <linux/uaccess.h>
+#include <linux/resume_user_mode.h>
+
+#include <asm/abi.h>
+#include <asm/asm.h>
+#include <linux/bitops.h>
+#include <asm/cacheflush.h>
+#include <asm/fpu.h>
+#include <asm/sim.h>
+#include <asm/ucontext.h>
+#include <asm/cpu-features.h>
+#include <asm/dsp.h>
+#include <asm/inst.h>
+#include <asm/msa.h>
+
+#include "signal-common.h"
+
+static int (*save_fp_context)(void __user *sc);
+static int (*restore_fp_context)(void __user *sc);
+
+struct sigframe {
+	u32 sf_ass[4];		/* argument save space for o32 */
+	u32 sf_pad[2];		/* Was: signal trampoline */
+
+	/* Matches struct ucontext from its uc_mcontext field onwards */
+	struct sigcontext sf_sc;
+	sigset_t sf_mask;
+	unsigned long long sf_extcontext[];
+};
+
+struct rt_sigframe {
+	u32 rs_ass[4];		/* argument save space for o32 */
+	u32 rs_pad[2];		/* Was: signal trampoline */
+	struct siginfo rs_info;
+	struct ucontext rs_uc;
+};
+
+#ifdef CONFIG_MIPS_FP_SUPPORT
+
+/*
+ * Thread saved context copy to/from a signal context presumed to be on the
+ * user stack, and therefore accessed with appropriate macros from uaccess.h.
+ */
+static int copy_fp_to_sigcontext(void __user *sc)
+{
+	struct mips_abi *abi = current->thread.abi;
+	uint64_t __user *fpregs = sc + abi->off_sc_fpregs;
+	uint32_t __user *csr = sc + abi->off_sc_fpc_csr;
+	int i;
+	int err = 0;
+	int inc = test_thread_flag(TIF_32BIT_FPREGS) ? 2 : 1;
+
+	for (i = 0; i < NUM_FPU_REGS; i += inc) {
+		err |=
+		    __put_user(get_fpr64(&current->thread.fpu.fpr[i], 0),
+			       &fpregs[i]);
+	}
+	err |= __put_user(current->thread.fpu.fcr31, csr);
+
+	return err;
+}
+
+static int copy_fp_from_sigcontext(void __user *sc)
+{
+	struct mips_abi *abi = current->thread.abi;
+	uint64_t __user *fpregs = sc + abi->off_sc_fpregs;
+	uint32_t __user *csr = sc + abi->off_sc_fpc_csr;
+	int i;
+	int err = 0;
+	int inc = test_thread_flag(TIF_32BIT_FPREGS) ? 2 : 1;
+	u64 fpr_val;
+
+	for (i = 0; i < NUM_FPU_REGS; i += inc) {
+		err |= __get_user(fpr_val, &fpregs[i]);
+		set_fpr64(&current->thread.fpu.fpr[i], 0, fpr_val);
+	}
+	err |= __get_user(current->thread.fpu.fcr31, csr);
+
+	return err;
+}
+
+#else /* !CONFIG_MIPS_FP_SUPPORT */
+
+static int copy_fp_to_sigcontext(void __user *sc)
+{
+	return 0;
+}
+
+static int copy_fp_from_sigcontext(void __user *sc)
+{
+	return 0;
+}
+
+#endif /* !CONFIG_MIPS_FP_SUPPORT */
+
+/*
+ * Wrappers for the assembly _{save,restore}_fp_context functions.
+ */
+static int save_hw_fp_context(void __user *sc)
+{
+	struct mips_abi *abi = current->thread.abi;
+	uint64_t __user *fpregs = sc + abi->off_sc_fpregs;
+	uint32_t __user *csr = sc + abi->off_sc_fpc_csr;
+
+	return _save_fp_context(fpregs, csr);
+}
+
+static int restore_hw_fp_context(void __user *sc)
+{
+	struct mips_abi *abi = current->thread.abi;
+	uint64_t __user *fpregs = sc + abi->off_sc_fpregs;
+	uint32_t __user *csr = sc + abi->off_sc_fpc_csr;
+
+	return _restore_fp_context(fpregs, csr);
+}
+
+/*
+ * Extended context handling.
+ */
+
+static inline void __user *sc_to_extcontext(void __user *sc)
+{
+	struct ucontext __user *uc;
+
+	/*
+	 * We can just pretend the sigcontext is always embedded in a struct
+	 * ucontext here, because the offset from sigcontext to extended
+	 * context is the same in the struct sigframe case.
+	 */
+	uc = container_of(sc, struct ucontext, uc_mcontext);
+	return &uc->uc_extcontext;
+}
+
+#ifdef CONFIG_CPU_HAS_MSA
+
+static int save_msa_extcontext(void __user *buf)
+{
+	struct msa_extcontext __user *msa = buf;
+	uint64_t val;
+	int i, err;
+
+	if (!thread_msa_context_live())
+		return 0;
+
+	/*
+	 * Ensure that we can't lose the live MSA context between checking
+	 * for it & writing it to memory.
+	 */
+	preempt_disable();
+
+	if (is_msa_enabled()) {
+		/*
+		 * There are no EVA versions of the vector register load/store
+		 * instructions, so MSA context has to be saved to kernel memory
+		 * and then copied to user memory. The save to kernel memory
+		 * should already have been done when handling scalar FP
+		 * context.
+		 */
+		BUG_ON(IS_ENABLED(CONFIG_EVA));
+
+		err = __put_user(read_msa_csr(), &msa->csr);
+		err |= _save_msa_all_upper(&msa->wr);
+
+		preempt_enable();
+	} else {
+		preempt_enable();
+
+		err = __put_user(current->thread.fpu.msacsr, &msa->csr);
+
+		for (i = 0; i < NUM_FPU_REGS; i++) {
+			val = get_fpr64(&current->thread.fpu.fpr[i], 1);
+			err |= __put_user(val, &msa->wr[i]);
+		}
+	}
+
+	err |= __put_user(MSA_EXTCONTEXT_MAGIC, &msa->ext.magic);
+	err |= __put_user(sizeof(*msa), &msa->ext.size);
+
+	return err ? -EFAULT : sizeof(*msa);
+}
+
+static int restore_msa_extcontext(void __user *buf, unsigned int size)
+{
+	struct msa_extcontext __user *msa = buf;
+	unsigned long long val;
+	unsigned int csr;
+	int i, err;
+
+	if (size != sizeof(*msa))
+		return -EINVAL;
+
+	err = get_user(csr, &msa->csr);
+	if (err)
+		return err;
+
+	preempt_disable();
+
+	if (is_msa_enabled()) {
+		/*
+		 * There are no EVA versions of the vector register load/store
+		 * instructions, so MSA context has to be copied to kernel
+		 * memory and later loaded to registers. The same is true of
+		 * scalar FP context, so FPU & MSA should have already been
+		 * disabled whilst handling scalar FP context.
+		 */
+		BUG_ON(IS_ENABLED(CONFIG_EVA));
+
+		write_msa_csr(csr);
+		err |= _restore_msa_all_upper(&msa->wr);
+		preempt_enable();
+	} else {
+		preempt_enable();
+
+		current->thread.fpu.msacsr = csr;
+
+		for (i = 0; i < NUM_FPU_REGS; i++) {
+			err |= __get_user(val, &msa->wr[i]);
+			set_fpr64(&current->thread.fpu.fpr[i], 1, val);
+		}
+	}
+
+	return err;
+}
+
+#else /* !CONFIG_CPU_HAS_MSA */
+
+static int save_msa_extcontext(void __user *buf)
+{
+	return 0;
+}
+
+static int restore_msa_extcontext(void __user *buf, unsigned int size)
+{
+	return SIGSYS;
+}
+
+#endif /* !CONFIG_CPU_HAS_MSA */
+
+static int save_extcontext(void __user *buf)
+{
+	int sz;
+
+	sz = save_msa_extcontext(buf);
+	if (sz < 0)
+		return sz;
+	buf += sz;
+
+	/* If no context was saved then trivially return */
+	if (!sz)
+		return 0;
+
+	/* Write the end marker */
+	if (__put_user(END_EXTCONTEXT_MAGIC, (u32 *)buf))
+		return -EFAULT;
+
+	sz += sizeof(((struct extcontext *)NULL)->magic);
+	return sz;
+}
+
+static int restore_extcontext(void __user *buf)
+{
+	struct extcontext ext;
+	int err;
+
+	while (1) {
+		err = __get_user(ext.magic, (unsigned int *)buf);
+		if (err)
+			return err;
+
+		if (ext.magic == END_EXTCONTEXT_MAGIC)
+			return 0;
+
+		err = __get_user(ext.size, (unsigned int *)(buf
+			+ offsetof(struct extcontext, size)));
+		if (err)
+			return err;
+
+		switch (ext.magic) {
+		case MSA_EXTCONTEXT_MAGIC:
+			err = restore_msa_extcontext(buf, ext.size);
+			break;
+
+		default:
+			err = -EINVAL;
+			break;
+		}
+
+		if (err)
+			return err;
+
+		buf += ext.size;
+	}
+}
+
+/*
+ * Helper routines
+ */
+int protected_save_fp_context(void __user *sc)
+{
+	struct mips_abi *abi = current->thread.abi;
+	uint64_t __user *fpregs = sc + abi->off_sc_fpregs;
+	uint32_t __user *csr = sc + abi->off_sc_fpc_csr;
+	uint32_t __user *used_math = sc + abi->off_sc_used_math;
+	unsigned int used, ext_sz;
+	int err;
+
+	used = used_math() ? USED_FP : 0;
+	if (!used)
+		goto fp_done;
+
+	if (!test_thread_flag(TIF_32BIT_FPREGS))
+		used |= USED_FR1;
+	if (test_thread_flag(TIF_HYBRID_FPREGS))
+		used |= USED_HYBRID_FPRS;
+
+	/*
+	 * EVA does not have userland equivalents of ldc1 or sdc1, so
+	 * save to the kernel FP context & copy that to userland below.
+	 */
+	if (IS_ENABLED(CONFIG_EVA))
+		lose_fpu(1);
+
+	while (1) {
+		lock_fpu_owner();
+		if (is_fpu_owner()) {
+			err = save_fp_context(sc);
+			unlock_fpu_owner();
+		} else {
+			unlock_fpu_owner();
+			err = copy_fp_to_sigcontext(sc);
+		}
+		if (likely(!err))
+			break;
+		/* touch the sigcontext and try again */
+		err = __put_user(0, &fpregs[0]) |
+			__put_user(0, &fpregs[31]) |
+			__put_user(0, csr);
+		if (err)
+			return err;	/* really bad sigcontext */
+	}
+
+fp_done:
+	ext_sz = err = save_extcontext(sc_to_extcontext(sc));
+	if (err < 0)
+		return err;
+	used |= ext_sz ? USED_EXTCONTEXT : 0;
+
+	return __put_user(used, used_math);
+}
+
+int protected_restore_fp_context(void __user *sc)
+{
+	struct mips_abi *abi = current->thread.abi;
+	uint64_t __user *fpregs = sc + abi->off_sc_fpregs;
+	uint32_t __user *csr = sc + abi->off_sc_fpc_csr;
+	uint32_t __user *used_math = sc + abi->off_sc_used_math;
+	unsigned int used;
+	int err, sig = 0, tmp __maybe_unused;
+
+	err = __get_user(used, used_math);
+	conditional_used_math(used & USED_FP);
+
+	/*
+	 * The signal handler may have used FPU; give it up if the program
+	 * doesn't want it following sigreturn.
+	 */
+	if (err || !(used & USED_FP))
+		lose_fpu(0);
+	if (err)
+		return err;
+	if (!(used & USED_FP))
+		goto fp_done;
+
+	err = sig = fpcsr_pending(csr);
+	if (err < 0)
+		return err;
+
+	/*
+	 * EVA does not have userland equivalents of ldc1 or sdc1, so we
+	 * disable the FPU here such that the code below simply copies to
+	 * the kernel FP context.
+	 */
+	if (IS_ENABLED(CONFIG_EVA))
+		lose_fpu(0);
+
+	while (1) {
+		lock_fpu_owner();
+		if (is_fpu_owner()) {
+			err = restore_fp_context(sc);
+			unlock_fpu_owner();
+		} else {
+			unlock_fpu_owner();
+			err = copy_fp_from_sigcontext(sc);
+		}
+		if (likely(!err))
+			break;
+		/* touch the sigcontext and try again */
+		err = __get_user(tmp, &fpregs[0]) |
+			__get_user(tmp, &fpregs[31]) |
+			__get_user(tmp, csr);
+		if (err)
+			break;	/* really bad sigcontext */
+	}
+
+fp_done:
+	if (!err && (used & USED_EXTCONTEXT))
+		err = restore_extcontext(sc_to_extcontext(sc));
+
+	return err ?: sig;
+}
+
+int setup_sigcontext(struct pt_regs *regs, struct sigcontext __user *sc)
+{
+	int err = 0;
+	int i;
+
+	err |= __put_user(regs->cp0_epc, &sc->sc_pc);
+
+	err |= __put_user(0, &sc->sc_regs[0]);
+	for (i = 1; i < 32; i++)
+		err |= __put_user(regs->regs[i], &sc->sc_regs[i]);
+
+#ifdef CONFIG_CPU_HAS_SMARTMIPS
+	err |= __put_user(regs->acx, &sc->sc_acx);
+#endif
+	err |= __put_user(regs->hi, &sc->sc_mdhi);
+	err |= __put_user(regs->lo, &sc->sc_mdlo);
+	if (cpu_has_dsp) {
+		err |= __put_user(mfhi1(), &sc->sc_hi1);
+		err |= __put_user(mflo1(), &sc->sc_lo1);
+		err |= __put_user(mfhi2(), &sc->sc_hi2);
+		err |= __put_user(mflo2(), &sc->sc_lo2);
+		err |= __put_user(mfhi3(), &sc->sc_hi3);
+		err |= __put_user(mflo3(), &sc->sc_lo3);
+		err |= __put_user(rddsp(DSP_MASK), &sc->sc_dsp);
+	}
+
+
+	/*
+	 * Save FPU state to signal context. Signal handler
+	 * will "inherit" current FPU state.
+	 */
+	err |= protected_save_fp_context(sc);
+
+	return err;
+}
+
+static size_t extcontext_max_size(void)
+{
+	size_t sz = 0;
+
+	/*
+	 * The assumption here is that between this point & the point at which
+	 * the extended context is saved the size of the context should only
+	 * ever be able to shrink (if the task is preempted), but never grow.
+	 * That is, what this function returns is an upper bound on the size of
+	 * the extended context for the current task at the current time.
+	 */
+
+	if (thread_msa_context_live())
+		sz += sizeof(struct msa_extcontext);
+
+	/* If any context is saved then we'll append the end marker */
+	if (sz)
+		sz += sizeof(((struct extcontext *)NULL)->magic);
+
+	return sz;
+}
+
+int fpcsr_pending(unsigned int __user *fpcsr)
+{
+	int err, sig = 0;
+	unsigned int csr, enabled;
+
+	err = __get_user(csr, fpcsr);
+	enabled = FPU_CSR_UNI_X | ((csr & FPU_CSR_ALL_E) << 5);
+	/*
+	 * If the signal handler set some FPU exceptions, clear it and
+	 * send SIGFPE.
+	 */
+	if (csr & enabled) {
+		csr &= ~enabled;
+		err |= __put_user(csr, fpcsr);
+		sig = SIGFPE;
+	}
+	return err ?: sig;
+}
+
+int restore_sigcontext(struct pt_regs *regs, struct sigcontext __user *sc)
+{
+	unsigned long treg;
+	int err = 0;
+	int i;
+
+	/* Always make any pending restarted system calls return -EINTR */
+	current->restart_block.fn = do_no_restart_syscall;
+
+	err |= __get_user(regs->cp0_epc, &sc->sc_pc);
+
+#ifdef CONFIG_CPU_HAS_SMARTMIPS
+	err |= __get_user(regs->acx, &sc->sc_acx);
+#endif
+	err |= __get_user(regs->hi, &sc->sc_mdhi);
+	err |= __get_user(regs->lo, &sc->sc_mdlo);
+	if (cpu_has_dsp) {
+		err |= __get_user(treg, &sc->sc_hi1); mthi1(treg);
+		err |= __get_user(treg, &sc->sc_lo1); mtlo1(treg);
+		err |= __get_user(treg, &sc->sc_hi2); mthi2(treg);
+		err |= __get_user(treg, &sc->sc_lo2); mtlo2(treg);
+		err |= __get_user(treg, &sc->sc_hi3); mthi3(treg);
+		err |= __get_user(treg, &sc->sc_lo3); mtlo3(treg);
+		err |= __get_user(treg, &sc->sc_dsp); wrdsp(treg, DSP_MASK);
+	}
+
+	for (i = 1; i < 32; i++)
+		err |= __get_user(regs->regs[i], &sc->sc_regs[i]);
+
+	return err ?: protected_restore_fp_context(sc);
+}
+
+#ifdef CONFIG_WAR_ICACHE_REFILLS
+#define SIGMASK		~(cpu_icache_line_size()-1)
+#else
+#define SIGMASK		ALMASK
+#endif
+
+void __user *get_sigframe(struct ksignal *ksig, struct pt_regs *regs,
+			  size_t frame_size)
+{
+	unsigned long sp;
+
+	/* Leave space for potential extended context */
+	frame_size += extcontext_max_size();
+
+	/* Default to using normal stack */
+	sp = regs->regs[29];
+
+	/*
+	 * If we are on the alternate signal stack and would overflow it, don't.
+	 * Return an always-bogus address instead so we will die with SIGSEGV.
+	 */
+	if (on_sig_stack(sp) && !likely(on_sig_stack(sp - frame_size)))
+		return (void __user __force *)(-1UL);
+
+	/*
+	 * FPU emulator may have it's own trampoline active just
+	 * above the user stack, 16-bytes before the next lowest
+	 * 16 byte boundary.  Try to avoid trashing it.
+	 */
+	sp -= 32;
+
+	sp = sigsp(sp, ksig);
+
+	return (void __user *)((sp - frame_size) & SIGMASK);
+}
+
+/*
+ * Atomically swap in the new signal mask, and wait for a signal.
+ */
+
+#ifdef CONFIG_TRAD_SIGNALS
+SYSCALL_DEFINE1(sigsuspend, sigset_t __user *, uset)
+{
+	return sys_rt_sigsuspend(uset, sizeof(sigset_t));
+}
+#endif
+
+#ifdef CONFIG_TRAD_SIGNALS
+SYSCALL_DEFINE3(sigaction, int, sig, const struct sigaction __user *, act,
+	struct sigaction __user *, oact)
+{
+	struct k_sigaction new_ka, old_ka;
+	int ret;
+	int err = 0;
+
+	if (act) {
+		old_sigset_t mask;
+
+		if (!access_ok(act, sizeof(*act)))
+			return -EFAULT;
+		err |= __get_user(new_ka.sa.sa_handler, &act->sa_handler);
+		err |= __get_user(new_ka.sa.sa_flags, &act->sa_flags);
+		err |= __get_user(mask, &act->sa_mask.sig[0]);
+		if (err)
+			return -EFAULT;
+
+		siginitset(&new_ka.sa.sa_mask, mask);
+	}
+
+	ret = do_sigaction(sig, act ? &new_ka : NULL, oact ? &old_ka : NULL);
+
+	if (!ret && oact) {
+		if (!access_ok(oact, sizeof(*oact)))
+			return -EFAULT;
+		err |= __put_user(old_ka.sa.sa_flags, &oact->sa_flags);
+		err |= __put_user(old_ka.sa.sa_handler, &oact->sa_handler);
+		err |= __put_user(old_ka.sa.sa_mask.sig[0], oact->sa_mask.sig);
+		err |= __put_user(0, &oact->sa_mask.sig[1]);
+		err |= __put_user(0, &oact->sa_mask.sig[2]);
+		err |= __put_user(0, &oact->sa_mask.sig[3]);
+		if (err)
+			return -EFAULT;
+	}
+
+	return ret;
+}
+#endif
+
+#ifdef CONFIG_TRAD_SIGNALS
+asmlinkage void sys_sigreturn(void)
+{
+	struct sigframe __user *frame;
+	struct pt_regs *regs;
+	sigset_t blocked;
+	int sig;
+
+	regs = current_pt_regs();
+	frame = (struct sigframe __user *)regs->regs[29];
+	if (!access_ok(frame, sizeof(*frame)))
+		goto badframe;
+	if (__copy_from_user(&blocked, &frame->sf_mask, sizeof(blocked)))
+		goto badframe;
+
+	set_current_blocked(&blocked);
+
+	sig = restore_sigcontext(regs, &frame->sf_sc);
+	if (sig < 0)
+		goto badframe;
+	else if (sig)
+		force_sig(sig);
+
+	/*
+	 * Don't let your children do this ...
+	 */
+	__asm__ __volatile__(
+		"move\t$29, %0\n\t"
+		"j\tsyscall_exit"
+		: /* no outputs */
+		: "r" (regs));
+	/* Unreached */
+
+badframe:
+	force_sig(SIGSEGV);
+}
+#endif /* CONFIG_TRAD_SIGNALS */
+
+asmlinkage void sys_rt_sigreturn(void)
+{
+	struct rt_sigframe __user *frame;
+	struct pt_regs *regs;
+	sigset_t set;
+	int sig;
+
+	regs = current_pt_regs();
+	frame = (struct rt_sigframe __user *)regs->regs[29];
+	if (!access_ok(frame, sizeof(*frame)))
+		goto badframe;
+	if (__copy_from_user(&set, &frame->rs_uc.uc_sigmask, sizeof(set)))
+		goto badframe;
+
+	set_current_blocked(&set);
+
+	sig = restore_sigcontext(regs, &frame->rs_uc.uc_mcontext);
+	if (sig < 0)
+		goto badframe;
+	else if (sig)
+		force_sig(sig);
+
+	if (restore_altstack(&frame->rs_uc.uc_stack))
+		goto badframe;
+
+	/*
+	 * Don't let your children do this ...
+	 */
+	__asm__ __volatile__(
+		"move\t$29, %0\n\t"
+		"j\tsyscall_exit"
+		: /* no outputs */
+		: "r" (regs));
+	/* Unreached */
+
+badframe:
+	force_sig(SIGSEGV);
+}
+
+#ifdef CONFIG_TRAD_SIGNALS
+static int setup_frame(void *sig_return, struct ksignal *ksig,
+		       struct pt_regs *regs, sigset_t *set)
+{
+	struct sigframe __user *frame;
+	int err = 0;
+
+	frame = get_sigframe(ksig, regs, sizeof(*frame));
+	if (!access_ok(frame, sizeof (*frame)))
+		return -EFAULT;
+
+	err |= setup_sigcontext(regs, &frame->sf_sc);
+	err |= __copy_to_user(&frame->sf_mask, set, sizeof(*set));
+	if (err)
+		return -EFAULT;
+
+	/*
+	 * Arguments to signal handler:
+	 *
+	 *   a0 = signal number
+	 *   a1 = 0 (should be cause)
+	 *   a2 = pointer to struct sigcontext
+	 *
+	 * $25 and c0_epc point to the signal handler, $29 points to the
+	 * struct sigframe.
+	 */
+	regs->regs[ 4] = ksig->sig;
+	regs->regs[ 5] = 0;
+	regs->regs[ 6] = (unsigned long) &frame->sf_sc;
+	regs->regs[29] = (unsigned long) frame;
+	regs->regs[31] = (unsigned long) sig_return;
+	regs->cp0_epc = regs->regs[25] = (unsigned long) ksig->ka.sa.sa_handler;
+
+	DEBUGP("SIG deliver (%s:%d): sp=0x%p pc=0x%lx ra=0x%lx\n",
+	       current->comm, current->pid,
+	       frame, regs->cp0_epc, regs->regs[31]);
+	return 0;
+}
+#endif
+
+static int setup_rt_frame(void *sig_return, struct ksignal *ksig,
+			  struct pt_regs *regs, sigset_t *set)
+{
+	struct rt_sigframe __user *frame;
+
+	frame = get_sigframe(ksig, regs, sizeof(*frame));
+	if (!access_ok(frame, sizeof (*frame)))
+		return -EFAULT;
+
+	/* Create siginfo.  */
+	if (copy_siginfo_to_user(&frame->rs_info, &ksig->info))
+		return -EFAULT;
+
+	/* Create the ucontext.	 */
+	if (__put_user(0, &frame->rs_uc.uc_flags))
+		return -EFAULT;
+	if (__put_user(NULL, &frame->rs_uc.uc_link))
+		return -EFAULT;
+	if (__save_altstack(&frame->rs_uc.uc_stack, regs->regs[29]))
+		return -EFAULT;
+	if (setup_sigcontext(regs, &frame->rs_uc.uc_mcontext))
+		return -EFAULT;
+	if (__copy_to_user(&frame->rs_uc.uc_sigmask, set, sizeof(*set)))
+		return -EFAULT;
+
+	/*
+	 * Arguments to signal handler:
+	 *
+	 *   a0 = signal number
+	 *   a1 = 0 (should be cause)
+	 *   a2 = pointer to ucontext
+	 *
+	 * $25 and c0_epc point to the signal handler, $29 points to
+	 * the struct rt_sigframe.
+	 */
+	regs->regs[ 4] = ksig->sig;
+	regs->regs[ 5] = (unsigned long) &frame->rs_info;
+	regs->regs[ 6] = (unsigned long) &frame->rs_uc;
+	regs->regs[29] = (unsigned long) frame;
+	regs->regs[31] = (unsigned long) sig_return;
+	regs->cp0_epc = regs->regs[25] = (unsigned long) ksig->ka.sa.sa_handler;
+
+	DEBUGP("SIG deliver (%s:%d): sp=0x%p pc=0x%lx ra=0x%lx\n",
+	       current->comm, current->pid,
+	       frame, regs->cp0_epc, regs->regs[31]);
+
+	return 0;
+}
+
+struct mips_abi mips_abi = {
+#ifdef CONFIG_TRAD_SIGNALS
+	.setup_frame	= setup_frame,
+#endif
+	.setup_rt_frame = setup_rt_frame,
+	.restart	= __NR_restart_syscall,
+
+	.off_sc_fpregs = offsetof(struct sigcontext, sc_fpregs),
+	.off_sc_fpc_csr = offsetof(struct sigcontext, sc_fpc_csr),
+	.off_sc_used_math = offsetof(struct sigcontext, sc_used_math),
+
+	.vdso		= &vdso_image,
+};
+
+static void handle_signal(struct ksignal *ksig, struct pt_regs *regs)
+{
+	sigset_t *oldset = sigmask_to_save();
+	int ret;
+	struct mips_abi *abi = current->thread.abi;
+	void *vdso = current->mm->context.vdso;
+
+	/*
+	 * If we were emulating a delay slot instruction, exit that frame such
+	 * that addresses in the sigframe are as expected for userland and we
+	 * don't have a problem if we reuse the thread's frame for an
+	 * instruction within the signal handler.
+	 */
+	dsemul_thread_rollback(regs);
+
+	if (regs->regs[0]) {
+		switch(regs->regs[2]) {
+		case ERESTART_RESTARTBLOCK:
+		case ERESTARTNOHAND:
+			regs->regs[2] = EINTR;
+			break;
+		case ERESTARTSYS:
+			if (!(ksig->ka.sa.sa_flags & SA_RESTART)) {
+				regs->regs[2] = EINTR;
+				break;
+			}
+			fallthrough;
+		case ERESTARTNOINTR:
+			regs->regs[7] = regs->regs[26];
+			regs->regs[2] = regs->regs[0];
+			regs->cp0_epc -= 4;
+		}
+
+		regs->regs[0] = 0;		/* Don't deal with this again.	*/
+	}
+
+	rseq_signal_deliver(ksig, regs);
+
+	if (sig_uses_siginfo(&ksig->ka, abi))
+		ret = abi->setup_rt_frame(vdso + abi->vdso->off_rt_sigreturn,
+					  ksig, regs, oldset);
+	else
+		ret = abi->setup_frame(vdso + abi->vdso->off_sigreturn,
+				       ksig, regs, oldset);
+
+	signal_setup_done(ret, ksig, 0);
+}
+
+static void do_signal(struct pt_regs *regs)
+{
+	struct ksignal ksig;
+
+	if (get_signal(&ksig)) {
+		/* Whee!  Actually deliver the signal.	*/
+		handle_signal(&ksig, regs);
+		return;
+	}
+
+	if (regs->regs[0]) {
+		switch (regs->regs[2]) {
+		case ERESTARTNOHAND:
+		case ERESTARTSYS:
+		case ERESTARTNOINTR:
+			regs->regs[2] = regs->regs[0];
+			regs->regs[7] = regs->regs[26];
+			regs->cp0_epc -= 4;
+			break;
+
+		case ERESTART_RESTARTBLOCK:
+			regs->regs[2] = current->thread.abi->restart;
+			regs->regs[7] = regs->regs[26];
+			regs->cp0_epc -= 4;
+			break;
+		}
+		regs->regs[0] = 0;	/* Don't deal with this again.	*/
+	}
+
+	/*
+	 * If there's no signal to deliver, we just put the saved sigmask
+	 * back
+	 */
+	restore_saved_sigmask();
+}
+
+/*
+ * notification of userspace execution resumption
+ * - triggered by the TIF_WORK_MASK flags
+ */
+asmlinkage void do_notify_resume(struct pt_regs *regs, void *unused,
+	__u32 thread_info_flags)
+{
+	local_irq_enable();
+
+	user_exit();
+
+	if (thread_info_flags & _TIF_UPROBE)
+		uprobe_notify_resume(regs);
+
+	/* deal with pending signal delivery */
+	if (thread_info_flags & (_TIF_SIGPENDING | _TIF_NOTIFY_SIGNAL))
+		do_signal(regs);
+
+	if (thread_info_flags & _TIF_NOTIFY_RESUME)
+		resume_user_mode_work(regs);
+
+	user_enter();
+}
+
+#if defined(CONFIG_SMP) && defined(CONFIG_MIPS_FP_SUPPORT)
+static int smp_save_fp_context(void __user *sc)
+{
+	return raw_cpu_has_fpu
+	       ? save_hw_fp_context(sc)
+	       : copy_fp_to_sigcontext(sc);
+}
+
+static int smp_restore_fp_context(void __user *sc)
+{
+	return raw_cpu_has_fpu
+	       ? restore_hw_fp_context(sc)
+	       : copy_fp_from_sigcontext(sc);
+}
+#endif
+
+static int signal_setup(void)
+{
+	/*
+	 * The offset from sigcontext to extended context should be the same
+	 * regardless of the type of signal, such that userland can always know
+	 * where to look if it wishes to find the extended context structures.
+	 */
+	BUILD_BUG_ON((offsetof(struct sigframe, sf_extcontext) -
+		      offsetof(struct sigframe, sf_sc)) !=
+		     (offsetof(struct rt_sigframe, rs_uc.uc_extcontext) -
+		      offsetof(struct rt_sigframe, rs_uc.uc_mcontext)));
+
+#if defined(CONFIG_SMP) && defined(CONFIG_MIPS_FP_SUPPORT)
+	/* For now just do the cpu_has_fpu check when the functions are invoked */
+	save_fp_context = smp_save_fp_context;
+	restore_fp_context = smp_restore_fp_context;
+#else
+	if (cpu_has_fpu) {
+		save_fp_context = save_hw_fp_context;
+		restore_fp_context = restore_hw_fp_context;
+	} else {
+		save_fp_context = copy_fp_to_sigcontext;
+		restore_fp_context = copy_fp_from_sigcontext;
+	}
+#endif /* CONFIG_SMP */
+
+	return 0;
+}
+
+arch_initcall(signal_setup);
diff --git a/arch/mips/kernel/signal32.c b/arch/mips/kernel/signal32.c
new file mode 100644
index 000000000..59b896543
--- /dev/null
+++ b/arch/mips/kernel/signal32.c
@@ -0,0 +1,78 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1991, 1992  Linus Torvalds
+ * Copyright (C) 1994 - 2000, 2006  Ralf Baechle
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ * Copyright (C) 2016, Imagination Technologies Ltd.
+ */
+#include <linux/compat.h>
+#include <linux/compiler.h>
+#include <linux/errno.h>
+#include <linux/kernel.h>
+#include <linux/signal.h>
+#include <linux/syscalls.h>
+
+#include <asm/compat-signal.h>
+#include <linux/uaccess.h>
+#include <asm/unistd.h>
+
+#include "signal-common.h"
+
+/* 32-bit compatibility types */
+
+typedef unsigned int __sighandler32_t;
+typedef void (*vfptr_t)(void);
+
+/*
+ * Atomically swap in the new signal mask, and wait for a signal.
+ */
+
+asmlinkage int sys32_sigsuspend(compat_sigset_t __user *uset)
+{
+	return compat_sys_rt_sigsuspend(uset, sizeof(compat_sigset_t));
+}
+
+SYSCALL_DEFINE3(32_sigaction, long, sig, const struct compat_sigaction __user *, act,
+	struct compat_sigaction __user *, oact)
+{
+	struct k_sigaction new_ka, old_ka;
+	int ret;
+	int err = 0;
+
+	if (act) {
+		old_sigset_t mask;
+		s32 handler;
+
+		if (!access_ok(act, sizeof(*act)))
+			return -EFAULT;
+		err |= __get_user(handler, &act->sa_handler);
+		new_ka.sa.sa_handler = (void __user *)(s64)handler;
+		err |= __get_user(new_ka.sa.sa_flags, &act->sa_flags);
+		err |= __get_user(mask, &act->sa_mask.sig[0]);
+		if (err)
+			return -EFAULT;
+
+		siginitset(&new_ka.sa.sa_mask, mask);
+	}
+
+	ret = do_sigaction(sig, act ? &new_ka : NULL, oact ? &old_ka : NULL);
+
+	if (!ret && oact) {
+		if (!access_ok(oact, sizeof(*oact)))
+			return -EFAULT;
+		err |= __put_user(old_ka.sa.sa_flags, &oact->sa_flags);
+		err |= __put_user((u32)(u64)old_ka.sa.sa_handler,
+				  &oact->sa_handler);
+		err |= __put_user(old_ka.sa.sa_mask.sig[0], oact->sa_mask.sig);
+		err |= __put_user(0, &oact->sa_mask.sig[1]);
+		err |= __put_user(0, &oact->sa_mask.sig[2]);
+		err |= __put_user(0, &oact->sa_mask.sig[3]);
+		if (err)
+			return -EFAULT;
+	}
+
+	return ret;
+}
diff --git a/arch/mips/kernel/signal_n32.c b/arch/mips/kernel/signal_n32.c
new file mode 100644
index 000000000..cfc77b694
--- /dev/null
+++ b/arch/mips/kernel/signal_n32.c
@@ -0,0 +1,148 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2003 Broadcom Corporation
+ */
+#include <linux/cache.h>
+#include <linux/sched.h>
+#include <linux/mm.h>
+#include <linux/smp.h>
+#include <linux/kernel.h>
+#include <linux/signal.h>
+#include <linux/errno.h>
+#include <linux/wait.h>
+#include <linux/ptrace.h>
+#include <linux/unistd.h>
+#include <linux/compat.h>
+#include <linux/bitops.h>
+
+#include <asm/abi.h>
+#include <asm/asm.h>
+#include <asm/cacheflush.h>
+#include <asm/compat-signal.h>
+#include <asm/sim.h>
+#include <linux/uaccess.h>
+#include <asm/ucontext.h>
+#include <asm/fpu.h>
+#include <asm/cpu-features.h>
+
+#include "signal-common.h"
+
+/*
+ * Including <asm/unistd.h> would give use the 64-bit syscall numbers ...
+ */
+#define __NR_N32_restart_syscall	6214
+
+extern int setup_sigcontext(struct pt_regs *, struct sigcontext __user *);
+extern int restore_sigcontext(struct pt_regs *, struct sigcontext __user *);
+
+struct ucontextn32 {
+	u32		    uc_flags;
+	s32		    uc_link;
+	compat_stack_t      uc_stack;
+	struct sigcontext   uc_mcontext;
+	compat_sigset_t	    uc_sigmask;	  /* mask last for extensibility */
+};
+
+struct rt_sigframe_n32 {
+	u32 rs_ass[4];			/* argument save space for o32 */
+	u32 rs_pad[2];			/* Was: signal trampoline */
+	struct compat_siginfo rs_info;
+	struct ucontextn32 rs_uc;
+};
+
+asmlinkage void sysn32_rt_sigreturn(void)
+{
+	struct rt_sigframe_n32 __user *frame;
+	struct pt_regs *regs;
+	sigset_t set;
+	int sig;
+
+	regs = current_pt_regs();
+	frame = (struct rt_sigframe_n32 __user *)regs->regs[29];
+	if (!access_ok(frame, sizeof(*frame)))
+		goto badframe;
+	if (__copy_conv_sigset_from_user(&set, &frame->rs_uc.uc_sigmask))
+		goto badframe;
+
+	set_current_blocked(&set);
+
+	sig = restore_sigcontext(regs, &frame->rs_uc.uc_mcontext);
+	if (sig < 0)
+		goto badframe;
+	else if (sig)
+		force_sig(sig);
+
+	if (compat_restore_altstack(&frame->rs_uc.uc_stack))
+		goto badframe;
+
+	/*
+	 * Don't let your children do this ...
+	 */
+	__asm__ __volatile__(
+		"move\t$29, %0\n\t"
+		"j\tsyscall_exit"
+		: /* no outputs */
+		: "r" (regs));
+	/* Unreached */
+
+badframe:
+	force_sig(SIGSEGV);
+}
+
+static int setup_rt_frame_n32(void *sig_return, struct ksignal *ksig,
+			      struct pt_regs *regs, sigset_t *set)
+{
+	struct rt_sigframe_n32 __user *frame;
+	int err = 0;
+
+	frame = get_sigframe(ksig, regs, sizeof(*frame));
+	if (!access_ok(frame, sizeof (*frame)))
+		return -EFAULT;
+
+	/* Create siginfo.  */
+	err |= copy_siginfo_to_user32(&frame->rs_info, &ksig->info);
+
+	/* Create the ucontext.	 */
+	err |= __put_user(0, &frame->rs_uc.uc_flags);
+	err |= __put_user(0, &frame->rs_uc.uc_link);
+	err |= __compat_save_altstack(&frame->rs_uc.uc_stack, regs->regs[29]);
+	err |= setup_sigcontext(regs, &frame->rs_uc.uc_mcontext);
+	err |= __copy_conv_sigset_to_user(&frame->rs_uc.uc_sigmask, set);
+
+	if (err)
+		return -EFAULT;
+
+	/*
+	 * Arguments to signal handler:
+	 *
+	 *   a0 = signal number
+	 *   a1 = 0 (should be cause)
+	 *   a2 = pointer to ucontext
+	 *
+	 * $25 and c0_epc point to the signal handler, $29 points to
+	 * the struct rt_sigframe.
+	 */
+	regs->regs[ 4] = ksig->sig;
+	regs->regs[ 5] = (unsigned long) &frame->rs_info;
+	regs->regs[ 6] = (unsigned long) &frame->rs_uc;
+	regs->regs[29] = (unsigned long) frame;
+	regs->regs[31] = (unsigned long) sig_return;
+	regs->cp0_epc = regs->regs[25] = (unsigned long) ksig->ka.sa.sa_handler;
+
+	DEBUGP("SIG deliver (%s:%d): sp=0x%p pc=0x%lx ra=0x%lx\n",
+	       current->comm, current->pid,
+	       frame, regs->cp0_epc, regs->regs[31]);
+
+	return 0;
+}
+
+struct mips_abi mips_abi_n32 = {
+	.setup_rt_frame = setup_rt_frame_n32,
+	.restart	= __NR_N32_restart_syscall,
+
+	.off_sc_fpregs = offsetof(struct sigcontext, sc_fpregs),
+	.off_sc_fpc_csr = offsetof(struct sigcontext, sc_fpc_csr),
+	.off_sc_used_math = offsetof(struct sigcontext, sc_used_math),
+
+	.vdso		= &vdso_image_n32,
+};
diff --git a/arch/mips/kernel/signal_o32.c b/arch/mips/kernel/signal_o32.c
new file mode 100644
index 000000000..299a7a28c
--- /dev/null
+++ b/arch/mips/kernel/signal_o32.c
@@ -0,0 +1,290 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1991, 1992  Linus Torvalds
+ * Copyright (C) 1994 - 2000, 2006  Ralf Baechle
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ * Copyright (C) 2016, Imagination Technologies Ltd.
+ */
+#include <linux/compiler.h>
+#include <linux/errno.h>
+#include <linux/signal.h>
+#include <linux/sched/signal.h>
+#include <linux/uaccess.h>
+
+#include <asm/abi.h>
+#include <asm/compat-signal.h>
+#include <asm/dsp.h>
+#include <asm/sim.h>
+#include <asm/unistd.h>
+
+#include "signal-common.h"
+
+/*
+ * Including <asm/unistd.h> would give use the 64-bit syscall numbers ...
+ */
+#define __NR_O32_restart_syscall	4253
+
+struct sigframe32 {
+	u32 sf_ass[4];		/* argument save space for o32 */
+	u32 sf_pad[2];		/* Was: signal trampoline */
+	struct sigcontext32 sf_sc;
+	compat_sigset_t sf_mask;
+};
+
+struct ucontext32 {
+	u32		    uc_flags;
+	s32		    uc_link;
+	compat_stack_t      uc_stack;
+	struct sigcontext32 uc_mcontext;
+	compat_sigset_t	    uc_sigmask;	  /* mask last for extensibility */
+};
+
+struct rt_sigframe32 {
+	u32 rs_ass[4];			/* argument save space for o32 */
+	u32 rs_pad[2];			/* Was: signal trampoline */
+	compat_siginfo_t rs_info;
+	struct ucontext32 rs_uc;
+};
+
+static int setup_sigcontext32(struct pt_regs *regs,
+			      struct sigcontext32 __user *sc)
+{
+	int err = 0;
+	int i;
+
+	err |= __put_user(regs->cp0_epc, &sc->sc_pc);
+
+	err |= __put_user(0, &sc->sc_regs[0]);
+	for (i = 1; i < 32; i++)
+		err |= __put_user(regs->regs[i], &sc->sc_regs[i]);
+
+	err |= __put_user(regs->hi, &sc->sc_mdhi);
+	err |= __put_user(regs->lo, &sc->sc_mdlo);
+	if (cpu_has_dsp) {
+		err |= __put_user(rddsp(DSP_MASK), &sc->sc_dsp);
+		err |= __put_user(mfhi1(), &sc->sc_hi1);
+		err |= __put_user(mflo1(), &sc->sc_lo1);
+		err |= __put_user(mfhi2(), &sc->sc_hi2);
+		err |= __put_user(mflo2(), &sc->sc_lo2);
+		err |= __put_user(mfhi3(), &sc->sc_hi3);
+		err |= __put_user(mflo3(), &sc->sc_lo3);
+	}
+
+	/*
+	 * Save FPU state to signal context.  Signal handler
+	 * will "inherit" current FPU state.
+	 */
+	err |= protected_save_fp_context(sc);
+
+	return err;
+}
+
+static int restore_sigcontext32(struct pt_regs *regs,
+				struct sigcontext32 __user *sc)
+{
+	int err = 0;
+	s32 treg;
+	int i;
+
+	/* Always make any pending restarted system calls return -EINTR */
+	current->restart_block.fn = do_no_restart_syscall;
+
+	err |= __get_user(regs->cp0_epc, &sc->sc_pc);
+	err |= __get_user(regs->hi, &sc->sc_mdhi);
+	err |= __get_user(regs->lo, &sc->sc_mdlo);
+	if (cpu_has_dsp) {
+		err |= __get_user(treg, &sc->sc_hi1); mthi1(treg);
+		err |= __get_user(treg, &sc->sc_lo1); mtlo1(treg);
+		err |= __get_user(treg, &sc->sc_hi2); mthi2(treg);
+		err |= __get_user(treg, &sc->sc_lo2); mtlo2(treg);
+		err |= __get_user(treg, &sc->sc_hi3); mthi3(treg);
+		err |= __get_user(treg, &sc->sc_lo3); mtlo3(treg);
+		err |= __get_user(treg, &sc->sc_dsp); wrdsp(treg, DSP_MASK);
+	}
+
+	for (i = 1; i < 32; i++)
+		err |= __get_user(regs->regs[i], &sc->sc_regs[i]);
+
+	return err ?: protected_restore_fp_context(sc);
+}
+
+static int setup_frame_32(void *sig_return, struct ksignal *ksig,
+			  struct pt_regs *regs, sigset_t *set)
+{
+	struct sigframe32 __user *frame;
+	int err = 0;
+
+	frame = get_sigframe(ksig, regs, sizeof(*frame));
+	if (!access_ok(frame, sizeof (*frame)))
+		return -EFAULT;
+
+	err |= setup_sigcontext32(regs, &frame->sf_sc);
+	err |= __copy_conv_sigset_to_user(&frame->sf_mask, set);
+
+	if (err)
+		return -EFAULT;
+
+	/*
+	 * Arguments to signal handler:
+	 *
+	 *   a0 = signal number
+	 *   a1 = 0 (should be cause)
+	 *   a2 = pointer to struct sigcontext
+	 *
+	 * $25 and c0_epc point to the signal handler, $29 points to the
+	 * struct sigframe.
+	 */
+	regs->regs[ 4] = ksig->sig;
+	regs->regs[ 5] = 0;
+	regs->regs[ 6] = (unsigned long) &frame->sf_sc;
+	regs->regs[29] = (unsigned long) frame;
+	regs->regs[31] = (unsigned long) sig_return;
+	regs->cp0_epc = regs->regs[25] = (unsigned long) ksig->ka.sa.sa_handler;
+
+	DEBUGP("SIG deliver (%s:%d): sp=0x%p pc=0x%lx ra=0x%lx\n",
+	       current->comm, current->pid,
+	       frame, regs->cp0_epc, regs->regs[31]);
+
+	return 0;
+}
+
+asmlinkage void sys32_rt_sigreturn(void)
+{
+	struct rt_sigframe32 __user *frame;
+	struct pt_regs *regs;
+	sigset_t set;
+	int sig;
+
+	regs = current_pt_regs();
+	frame = (struct rt_sigframe32 __user *)regs->regs[29];
+	if (!access_ok(frame, sizeof(*frame)))
+		goto badframe;
+	if (__copy_conv_sigset_from_user(&set, &frame->rs_uc.uc_sigmask))
+		goto badframe;
+
+	set_current_blocked(&set);
+
+	sig = restore_sigcontext32(regs, &frame->rs_uc.uc_mcontext);
+	if (sig < 0)
+		goto badframe;
+	else if (sig)
+		force_sig(sig);
+
+	if (compat_restore_altstack(&frame->rs_uc.uc_stack))
+		goto badframe;
+
+	/*
+	 * Don't let your children do this ...
+	 */
+	__asm__ __volatile__(
+		"move\t$29, %0\n\t"
+		"j\tsyscall_exit"
+		: /* no outputs */
+		: "r" (regs));
+	/* Unreached */
+
+badframe:
+	force_sig(SIGSEGV);
+}
+
+static int setup_rt_frame_32(void *sig_return, struct ksignal *ksig,
+			     struct pt_regs *regs, sigset_t *set)
+{
+	struct rt_sigframe32 __user *frame;
+	int err = 0;
+
+	frame = get_sigframe(ksig, regs, sizeof(*frame));
+	if (!access_ok(frame, sizeof (*frame)))
+		return -EFAULT;
+
+	/* Convert (siginfo_t -> compat_siginfo_t) and copy to user. */
+	err |= copy_siginfo_to_user32(&frame->rs_info, &ksig->info);
+
+	/* Create the ucontext.	 */
+	err |= __put_user(0, &frame->rs_uc.uc_flags);
+	err |= __put_user(0, &frame->rs_uc.uc_link);
+	err |= __compat_save_altstack(&frame->rs_uc.uc_stack, regs->regs[29]);
+	err |= setup_sigcontext32(regs, &frame->rs_uc.uc_mcontext);
+	err |= __copy_conv_sigset_to_user(&frame->rs_uc.uc_sigmask, set);
+
+	if (err)
+		return -EFAULT;
+
+	/*
+	 * Arguments to signal handler:
+	 *
+	 *   a0 = signal number
+	 *   a1 = 0 (should be cause)
+	 *   a2 = pointer to ucontext
+	 *
+	 * $25 and c0_epc point to the signal handler, $29 points to
+	 * the struct rt_sigframe32.
+	 */
+	regs->regs[ 4] = ksig->sig;
+	regs->regs[ 5] = (unsigned long) &frame->rs_info;
+	regs->regs[ 6] = (unsigned long) &frame->rs_uc;
+	regs->regs[29] = (unsigned long) frame;
+	regs->regs[31] = (unsigned long) sig_return;
+	regs->cp0_epc = regs->regs[25] = (unsigned long) ksig->ka.sa.sa_handler;
+
+	DEBUGP("SIG deliver (%s:%d): sp=0x%p pc=0x%lx ra=0x%lx\n",
+	       current->comm, current->pid,
+	       frame, regs->cp0_epc, regs->regs[31]);
+
+	return 0;
+}
+
+/*
+ * o32 compatibility on 64-bit kernels, without DSP ASE
+ */
+struct mips_abi mips_abi_32 = {
+	.setup_frame	= setup_frame_32,
+	.setup_rt_frame = setup_rt_frame_32,
+	.restart	= __NR_O32_restart_syscall,
+
+	.off_sc_fpregs = offsetof(struct sigcontext32, sc_fpregs),
+	.off_sc_fpc_csr = offsetof(struct sigcontext32, sc_fpc_csr),
+	.off_sc_used_math = offsetof(struct sigcontext32, sc_used_math),
+
+	.vdso		= &vdso_image_o32,
+};
+
+
+asmlinkage void sys32_sigreturn(void)
+{
+	struct sigframe32 __user *frame;
+	struct pt_regs *regs;
+	sigset_t blocked;
+	int sig;
+
+	regs = current_pt_regs();
+	frame = (struct sigframe32 __user *)regs->regs[29];
+	if (!access_ok(frame, sizeof(*frame)))
+		goto badframe;
+	if (__copy_conv_sigset_from_user(&blocked, &frame->sf_mask))
+		goto badframe;
+
+	set_current_blocked(&blocked);
+
+	sig = restore_sigcontext32(regs, &frame->sf_sc);
+	if (sig < 0)
+		goto badframe;
+	else if (sig)
+		force_sig(sig);
+
+	/*
+	 * Don't let your children do this ...
+	 */
+	__asm__ __volatile__(
+		"move\t$29, %0\n\t"
+		"j\tsyscall_exit"
+		: /* no outputs */
+		: "r" (regs));
+	/* Unreached */
+
+badframe:
+	force_sig(SIGSEGV);
+}
diff --git a/arch/mips/kernel/smp-bmips.c b/arch/mips/kernel/smp-bmips.c
new file mode 100644
index 000000000..f5d7bfa34
--- /dev/null
+++ b/arch/mips/kernel/smp-bmips.c
@@ -0,0 +1,672 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2011 by Kevin Cernekee (cernekee@gmail.com)
+ *
+ * SMP support for BMIPS
+ */
+
+#include <linux/init.h>
+#include <linux/sched.h>
+#include <linux/sched/hotplug.h>
+#include <linux/sched/task_stack.h>
+#include <linux/mm.h>
+#include <linux/delay.h>
+#include <linux/smp.h>
+#include <linux/interrupt.h>
+#include <linux/spinlock.h>
+#include <linux/cpu.h>
+#include <linux/cpumask.h>
+#include <linux/reboot.h>
+#include <linux/io.h>
+#include <linux/compiler.h>
+#include <linux/linkage.h>
+#include <linux/bug.h>
+#include <linux/kernel.h>
+#include <linux/kexec.h>
+#include <linux/irq.h>
+
+#include <asm/time.h>
+#include <asm/processor.h>
+#include <asm/bootinfo.h>
+#include <asm/cacheflush.h>
+#include <asm/tlbflush.h>
+#include <asm/mipsregs.h>
+#include <asm/bmips.h>
+#include <asm/traps.h>
+#include <asm/barrier.h>
+#include <asm/cpu-features.h>
+
+static int __maybe_unused max_cpus = 1;
+
+/* these may be configured by the platform code */
+int bmips_smp_enabled = 1;
+int bmips_cpu_offset;
+cpumask_t bmips_booted_mask;
+unsigned long bmips_tp1_irqs = IE_IRQ1;
+
+#define RESET_FROM_KSEG0		0x80080800
+#define RESET_FROM_KSEG1		0xa0080800
+
+static void bmips_set_reset_vec(int cpu, u32 val);
+
+#ifdef CONFIG_SMP
+
+/* initial $sp, $gp - used by arch/mips/kernel/bmips_vec.S */
+unsigned long bmips_smp_boot_sp;
+unsigned long bmips_smp_boot_gp;
+
+static void bmips43xx_send_ipi_single(int cpu, unsigned int action);
+static void bmips5000_send_ipi_single(int cpu, unsigned int action);
+static irqreturn_t bmips43xx_ipi_interrupt(int irq, void *dev_id);
+static irqreturn_t bmips5000_ipi_interrupt(int irq, void *dev_id);
+
+/* SW interrupts 0,1 are used for interprocessor signaling */
+#define IPI0_IRQ			(MIPS_CPU_IRQ_BASE + 0)
+#define IPI1_IRQ			(MIPS_CPU_IRQ_BASE + 1)
+
+#define CPUNUM(cpu, shift)		(((cpu) + bmips_cpu_offset) << (shift))
+#define ACTION_CLR_IPI(cpu, ipi)	(0x2000 | CPUNUM(cpu, 9) | ((ipi) << 8))
+#define ACTION_SET_IPI(cpu, ipi)	(0x3000 | CPUNUM(cpu, 9) | ((ipi) << 8))
+#define ACTION_BOOT_THREAD(cpu)		(0x08 | CPUNUM(cpu, 0))
+
+static void __init bmips_smp_setup(void)
+{
+	int i, cpu = 1, boot_cpu = 0;
+	int cpu_hw_intr;
+
+	switch (current_cpu_type()) {
+	case CPU_BMIPS4350:
+	case CPU_BMIPS4380:
+		/* arbitration priority */
+		clear_c0_brcm_cmt_ctrl(0x30);
+
+		/* NBK and weak order flags */
+		set_c0_brcm_config_0(0x30000);
+
+		/* Find out if we are running on TP0 or TP1 */
+		boot_cpu = !!(read_c0_brcm_cmt_local() & (1 << 31));
+
+		/*
+		 * MIPS interrupts 0,1 (SW INT 0,1) cross over to the other
+		 * thread
+		 * MIPS interrupt 2 (HW INT 0) is the CPU0 L1 controller output
+		 * MIPS interrupt 3 (HW INT 1) is the CPU1 L1 controller output
+		 */
+		if (boot_cpu == 0)
+			cpu_hw_intr = 0x02;
+		else
+			cpu_hw_intr = 0x1d;
+
+		change_c0_brcm_cmt_intr(0xf8018000,
+					(cpu_hw_intr << 27) | (0x03 << 15));
+
+		/* single core, 2 threads (2 pipelines) */
+		max_cpus = 2;
+
+		break;
+	case CPU_BMIPS5000:
+		/* enable raceless SW interrupts */
+		set_c0_brcm_config(0x03 << 22);
+
+		/* route HW interrupt 0 to CPU0, HW interrupt 1 to CPU1 */
+		change_c0_brcm_mode(0x1f << 27, 0x02 << 27);
+
+		/* N cores, 2 threads per core */
+		max_cpus = (((read_c0_brcm_config() >> 6) & 0x03) + 1) << 1;
+
+		/* clear any pending SW interrupts */
+		for (i = 0; i < max_cpus; i++) {
+			write_c0_brcm_action(ACTION_CLR_IPI(i, 0));
+			write_c0_brcm_action(ACTION_CLR_IPI(i, 1));
+		}
+
+		break;
+	default:
+		max_cpus = 1;
+	}
+
+	if (!bmips_smp_enabled)
+		max_cpus = 1;
+
+	/* this can be overridden by the BSP */
+	if (!board_ebase_setup)
+		board_ebase_setup = &bmips_ebase_setup;
+
+	if (max_cpus > 1) {
+		__cpu_number_map[boot_cpu] = 0;
+		__cpu_logical_map[0] = boot_cpu;
+
+		for (i = 0; i < max_cpus; i++) {
+			if (i != boot_cpu) {
+				__cpu_number_map[i] = cpu;
+				__cpu_logical_map[cpu] = i;
+				cpu++;
+			}
+			set_cpu_possible(i, 1);
+			set_cpu_present(i, 1);
+		}
+	} else {
+		__cpu_number_map[0] = boot_cpu;
+		__cpu_logical_map[0] = 0;
+		set_cpu_possible(0, 1);
+		set_cpu_present(0, 1);
+	}
+}
+
+/*
+ * IPI IRQ setup - runs on CPU0
+ */
+static void bmips_prepare_cpus(unsigned int max_cpus)
+{
+	irqreturn_t (*bmips_ipi_interrupt)(int irq, void *dev_id);
+
+	switch (current_cpu_type()) {
+	case CPU_BMIPS4350:
+	case CPU_BMIPS4380:
+		bmips_ipi_interrupt = bmips43xx_ipi_interrupt;
+		break;
+	case CPU_BMIPS5000:
+		bmips_ipi_interrupt = bmips5000_ipi_interrupt;
+		break;
+	default:
+		return;
+	}
+
+	if (request_irq(IPI0_IRQ, bmips_ipi_interrupt,
+			IRQF_PERCPU | IRQF_NO_SUSPEND, "smp_ipi0", NULL))
+		panic("Can't request IPI0 interrupt");
+	if (request_irq(IPI1_IRQ, bmips_ipi_interrupt,
+			IRQF_PERCPU | IRQF_NO_SUSPEND, "smp_ipi1", NULL))
+		panic("Can't request IPI1 interrupt");
+}
+
+/*
+ * Tell the hardware to boot CPUx - runs on CPU0
+ */
+static int bmips_boot_secondary(int cpu, struct task_struct *idle)
+{
+	bmips_smp_boot_sp = __KSTK_TOS(idle);
+	bmips_smp_boot_gp = (unsigned long)task_thread_info(idle);
+	mb();
+
+	/*
+	 * Initial boot sequence for secondary CPU:
+	 *   bmips_reset_nmi_vec @ a000_0000 ->
+	 *   bmips_smp_entry ->
+	 *   plat_wired_tlb_setup (cached function call; optional) ->
+	 *   start_secondary (cached jump)
+	 *
+	 * Warm restart sequence:
+	 *   play_dead WAIT loop ->
+	 *   bmips_smp_int_vec @ BMIPS_WARM_RESTART_VEC ->
+	 *   eret to play_dead ->
+	 *   bmips_secondary_reentry ->
+	 *   start_secondary
+	 */
+
+	pr_info("SMP: Booting CPU%d...\n", cpu);
+
+	if (cpumask_test_cpu(cpu, &bmips_booted_mask)) {
+		/* kseg1 might not exist if this CPU enabled XKS01 */
+		bmips_set_reset_vec(cpu, RESET_FROM_KSEG0);
+
+		switch (current_cpu_type()) {
+		case CPU_BMIPS4350:
+		case CPU_BMIPS4380:
+			bmips43xx_send_ipi_single(cpu, 0);
+			break;
+		case CPU_BMIPS5000:
+			bmips5000_send_ipi_single(cpu, 0);
+			break;
+		}
+	} else {
+		bmips_set_reset_vec(cpu, RESET_FROM_KSEG1);
+
+		switch (current_cpu_type()) {
+		case CPU_BMIPS4350:
+		case CPU_BMIPS4380:
+			/* Reset slave TP1 if booting from TP0 */
+			if (cpu_logical_map(cpu) == 1)
+				set_c0_brcm_cmt_ctrl(0x01);
+			break;
+		case CPU_BMIPS5000:
+			write_c0_brcm_action(ACTION_BOOT_THREAD(cpu));
+			break;
+		}
+		cpumask_set_cpu(cpu, &bmips_booted_mask);
+	}
+
+	return 0;
+}
+
+/*
+ * Early setup - runs on secondary CPU after cache probe
+ */
+static void bmips_init_secondary(void)
+{
+	bmips_cpu_setup();
+
+	switch (current_cpu_type()) {
+	case CPU_BMIPS4350:
+	case CPU_BMIPS4380:
+		clear_c0_cause(smp_processor_id() ? C_SW1 : C_SW0);
+		break;
+	case CPU_BMIPS5000:
+		write_c0_brcm_action(ACTION_CLR_IPI(smp_processor_id(), 0));
+		cpu_set_core(&current_cpu_data, (read_c0_brcm_config() >> 25) & 3);
+		break;
+	}
+}
+
+/*
+ * Late setup - runs on secondary CPU before entering the idle loop
+ */
+static void bmips_smp_finish(void)
+{
+	pr_info("SMP: CPU%d is running\n", smp_processor_id());
+
+	/* make sure there won't be a timer interrupt for a little while */
+	write_c0_compare(read_c0_count() + mips_hpt_frequency / HZ);
+
+	irq_enable_hazard();
+	set_c0_status(IE_SW0 | IE_SW1 | bmips_tp1_irqs | IE_IRQ5 | ST0_IE);
+	irq_enable_hazard();
+}
+
+/*
+ * BMIPS5000 raceless IPIs
+ *
+ * Each CPU has two inbound SW IRQs which are independent of all other CPUs.
+ * IPI0 is used for SMP_RESCHEDULE_YOURSELF
+ * IPI1 is used for SMP_CALL_FUNCTION
+ */
+
+static void bmips5000_send_ipi_single(int cpu, unsigned int action)
+{
+	write_c0_brcm_action(ACTION_SET_IPI(cpu, action == SMP_CALL_FUNCTION));
+}
+
+static irqreturn_t bmips5000_ipi_interrupt(int irq, void *dev_id)
+{
+	int action = irq - IPI0_IRQ;
+
+	write_c0_brcm_action(ACTION_CLR_IPI(smp_processor_id(), action));
+
+	if (action == 0)
+		scheduler_ipi();
+	else
+		generic_smp_call_function_interrupt();
+
+	return IRQ_HANDLED;
+}
+
+static void bmips5000_send_ipi_mask(const struct cpumask *mask,
+	unsigned int action)
+{
+	unsigned int i;
+
+	for_each_cpu(i, mask)
+		bmips5000_send_ipi_single(i, action);
+}
+
+/*
+ * BMIPS43xx racey IPIs
+ *
+ * We use one inbound SW IRQ for each CPU.
+ *
+ * A spinlock must be held in order to keep CPUx from accidentally clearing
+ * an incoming IPI when it writes CP0 CAUSE to raise an IPI on CPUy.  The
+ * same spinlock is used to protect the action masks.
+ */
+
+static DEFINE_SPINLOCK(ipi_lock);
+static DEFINE_PER_CPU(int, ipi_action_mask);
+
+static void bmips43xx_send_ipi_single(int cpu, unsigned int action)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&ipi_lock, flags);
+	set_c0_cause(cpu ? C_SW1 : C_SW0);
+	per_cpu(ipi_action_mask, cpu) |= action;
+	irq_enable_hazard();
+	spin_unlock_irqrestore(&ipi_lock, flags);
+}
+
+static irqreturn_t bmips43xx_ipi_interrupt(int irq, void *dev_id)
+{
+	unsigned long flags;
+	int action, cpu = irq - IPI0_IRQ;
+
+	spin_lock_irqsave(&ipi_lock, flags);
+	action = __this_cpu_read(ipi_action_mask);
+	per_cpu(ipi_action_mask, cpu) = 0;
+	clear_c0_cause(cpu ? C_SW1 : C_SW0);
+	spin_unlock_irqrestore(&ipi_lock, flags);
+
+	if (action & SMP_RESCHEDULE_YOURSELF)
+		scheduler_ipi();
+	if (action & SMP_CALL_FUNCTION)
+		generic_smp_call_function_interrupt();
+
+	return IRQ_HANDLED;
+}
+
+static void bmips43xx_send_ipi_mask(const struct cpumask *mask,
+	unsigned int action)
+{
+	unsigned int i;
+
+	for_each_cpu(i, mask)
+		bmips43xx_send_ipi_single(i, action);
+}
+
+#ifdef CONFIG_HOTPLUG_CPU
+
+static int bmips_cpu_disable(void)
+{
+	unsigned int cpu = smp_processor_id();
+
+	pr_info("SMP: CPU%d is offline\n", cpu);
+
+	set_cpu_online(cpu, false);
+	calculate_cpu_foreign_map();
+	irq_migrate_all_off_this_cpu();
+	clear_c0_status(IE_IRQ5);
+
+	local_flush_tlb_all();
+	local_flush_icache_range(0, ~0);
+
+	return 0;
+}
+
+static void bmips_cpu_die(unsigned int cpu)
+{
+}
+
+void __ref play_dead(void)
+{
+	idle_task_exit();
+
+	/* flush data cache */
+	_dma_cache_wback_inv(0, ~0);
+
+	/*
+	 * Wakeup is on SW0 or SW1; disable everything else
+	 * Use BEV !IV (BMIPS_WARM_RESTART_VEC) to avoid the regular Linux
+	 * IRQ handlers; this clears ST0_IE and returns immediately.
+	 */
+	clear_c0_cause(CAUSEF_IV | C_SW0 | C_SW1);
+	change_c0_status(
+		IE_IRQ5 | bmips_tp1_irqs | IE_SW0 | IE_SW1 | ST0_IE | ST0_BEV,
+		IE_SW0 | IE_SW1 | ST0_IE | ST0_BEV);
+	irq_disable_hazard();
+
+	/*
+	 * wait for SW interrupt from bmips_boot_secondary(), then jump
+	 * back to start_secondary()
+	 */
+	__asm__ __volatile__(
+	"	wait\n"
+	"	j	bmips_secondary_reentry\n"
+	: : : "memory");
+}
+
+#endif /* CONFIG_HOTPLUG_CPU */
+
+const struct plat_smp_ops bmips43xx_smp_ops = {
+	.smp_setup		= bmips_smp_setup,
+	.prepare_cpus		= bmips_prepare_cpus,
+	.boot_secondary		= bmips_boot_secondary,
+	.smp_finish		= bmips_smp_finish,
+	.init_secondary		= bmips_init_secondary,
+	.send_ipi_single	= bmips43xx_send_ipi_single,
+	.send_ipi_mask		= bmips43xx_send_ipi_mask,
+#ifdef CONFIG_HOTPLUG_CPU
+	.cpu_disable		= bmips_cpu_disable,
+	.cpu_die		= bmips_cpu_die,
+#endif
+#ifdef CONFIG_KEXEC
+	.kexec_nonboot_cpu	= kexec_nonboot_cpu_jump,
+#endif
+};
+
+const struct plat_smp_ops bmips5000_smp_ops = {
+	.smp_setup		= bmips_smp_setup,
+	.prepare_cpus		= bmips_prepare_cpus,
+	.boot_secondary		= bmips_boot_secondary,
+	.smp_finish		= bmips_smp_finish,
+	.init_secondary		= bmips_init_secondary,
+	.send_ipi_single	= bmips5000_send_ipi_single,
+	.send_ipi_mask		= bmips5000_send_ipi_mask,
+#ifdef CONFIG_HOTPLUG_CPU
+	.cpu_disable		= bmips_cpu_disable,
+	.cpu_die		= bmips_cpu_die,
+#endif
+#ifdef CONFIG_KEXEC
+	.kexec_nonboot_cpu	= kexec_nonboot_cpu_jump,
+#endif
+};
+
+#endif /* CONFIG_SMP */
+
+/***********************************************************************
+ * BMIPS vector relocation
+ * This is primarily used for SMP boot, but it is applicable to some
+ * UP BMIPS systems as well.
+ ***********************************************************************/
+
+static void bmips_wr_vec(unsigned long dst, char *start, char *end)
+{
+	memcpy((void *)dst, start, end - start);
+	dma_cache_wback(dst, end - start);
+	local_flush_icache_range(dst, dst + (end - start));
+	instruction_hazard();
+}
+
+static inline void bmips_nmi_handler_setup(void)
+{
+	bmips_wr_vec(BMIPS_NMI_RESET_VEC, bmips_reset_nmi_vec,
+		bmips_reset_nmi_vec_end);
+	bmips_wr_vec(BMIPS_WARM_RESTART_VEC, bmips_smp_int_vec,
+		bmips_smp_int_vec_end);
+}
+
+struct reset_vec_info {
+	int cpu;
+	u32 val;
+};
+
+static void bmips_set_reset_vec_remote(void *vinfo)
+{
+	struct reset_vec_info *info = vinfo;
+	int shift = info->cpu & 0x01 ? 16 : 0;
+	u32 mask = ~(0xffff << shift), val = info->val >> 16;
+
+	preempt_disable();
+	if (smp_processor_id() > 0) {
+		smp_call_function_single(0, &bmips_set_reset_vec_remote,
+					 info, 1);
+	} else {
+		if (info->cpu & 0x02) {
+			/* BMIPS5200 "should" use mask/shift, but it's buggy */
+			bmips_write_zscm_reg(0xa0, (val << 16) | val);
+			bmips_read_zscm_reg(0xa0);
+		} else {
+			write_c0_brcm_bootvec((read_c0_brcm_bootvec() & mask) |
+					      (val << shift));
+		}
+	}
+	preempt_enable();
+}
+
+static void bmips_set_reset_vec(int cpu, u32 val)
+{
+	struct reset_vec_info info;
+
+	if (current_cpu_type() == CPU_BMIPS5000) {
+		/* this needs to run from CPU0 (which is always online) */
+		info.cpu = cpu;
+		info.val = val;
+		bmips_set_reset_vec_remote(&info);
+	} else {
+		void __iomem *cbr = BMIPS_GET_CBR();
+
+		if (cpu == 0)
+			__raw_writel(val, cbr + BMIPS_RELO_VECTOR_CONTROL_0);
+		else {
+			if (current_cpu_type() != CPU_BMIPS4380)
+				return;
+			__raw_writel(val, cbr + BMIPS_RELO_VECTOR_CONTROL_1);
+		}
+	}
+	__sync();
+	back_to_back_c0_hazard();
+}
+
+void bmips_ebase_setup(void)
+{
+	unsigned long new_ebase = ebase;
+
+	BUG_ON(ebase != CKSEG0);
+
+	switch (current_cpu_type()) {
+	case CPU_BMIPS4350:
+		/*
+		 * BMIPS4350 cannot relocate the normal vectors, but it
+		 * can relocate the BEV=1 vectors.  So CPU1 starts up at
+		 * the relocated BEV=1, IV=0 general exception vector @
+		 * 0xa000_0380.
+		 *
+		 * set_uncached_handler() is used here because:
+		 *  - CPU1 will run this from uncached space
+		 *  - None of the cacheflush functions are set up yet
+		 */
+		set_uncached_handler(BMIPS_WARM_RESTART_VEC - CKSEG0,
+			&bmips_smp_int_vec, 0x80);
+		__sync();
+		return;
+	case CPU_BMIPS3300:
+	case CPU_BMIPS4380:
+		/*
+		 * 0x8000_0000: reset/NMI (initially in kseg1)
+		 * 0x8000_0400: normal vectors
+		 */
+		new_ebase = 0x80000400;
+		bmips_set_reset_vec(0, RESET_FROM_KSEG0);
+		break;
+	case CPU_BMIPS5000:
+		/*
+		 * 0x8000_0000: reset/NMI (initially in kseg1)
+		 * 0x8000_1000: normal vectors
+		 */
+		new_ebase = 0x80001000;
+		bmips_set_reset_vec(0, RESET_FROM_KSEG0);
+		write_c0_ebase(new_ebase);
+		break;
+	default:
+		return;
+	}
+
+	board_nmi_handler_setup = &bmips_nmi_handler_setup;
+	ebase = new_ebase;
+}
+
+asmlinkage void __weak plat_wired_tlb_setup(void)
+{
+	/*
+	 * Called when starting/restarting a secondary CPU.
+	 * Kernel stacks and other important data might only be accessible
+	 * once the wired entries are present.
+	 */
+}
+
+void bmips_cpu_setup(void)
+{
+	void __iomem __maybe_unused *cbr = BMIPS_GET_CBR();
+	u32 __maybe_unused cfg;
+
+	switch (current_cpu_type()) {
+	case CPU_BMIPS3300:
+		/* Set BIU to async mode */
+		set_c0_brcm_bus_pll(BIT(22));
+		__sync();
+
+		/* put the BIU back in sync mode */
+		clear_c0_brcm_bus_pll(BIT(22));
+
+		/* clear BHTD to enable branch history table */
+		clear_c0_brcm_reset(BIT(16));
+
+		/* Flush and enable RAC */
+		cfg = __raw_readl(cbr + BMIPS_RAC_CONFIG);
+		__raw_writel(cfg | 0x100, cbr + BMIPS_RAC_CONFIG);
+		__raw_readl(cbr + BMIPS_RAC_CONFIG);
+
+		cfg = __raw_readl(cbr + BMIPS_RAC_CONFIG);
+		__raw_writel(cfg | 0xf, cbr + BMIPS_RAC_CONFIG);
+		__raw_readl(cbr + BMIPS_RAC_CONFIG);
+
+		cfg = __raw_readl(cbr + BMIPS_RAC_ADDRESS_RANGE);
+		__raw_writel(cfg | 0x0fff0000, cbr + BMIPS_RAC_ADDRESS_RANGE);
+		__raw_readl(cbr + BMIPS_RAC_ADDRESS_RANGE);
+		break;
+
+	case CPU_BMIPS4380:
+		/* CBG workaround for early BMIPS4380 CPUs */
+		switch (read_c0_prid()) {
+		case 0x2a040:
+		case 0x2a042:
+		case 0x2a044:
+		case 0x2a060:
+			cfg = __raw_readl(cbr + BMIPS_L2_CONFIG);
+			__raw_writel(cfg & ~0x07000000, cbr + BMIPS_L2_CONFIG);
+			__raw_readl(cbr + BMIPS_L2_CONFIG);
+		}
+
+		/* clear BHTD to enable branch history table */
+		clear_c0_brcm_config_0(BIT(21));
+
+		/* XI/ROTR enable */
+		set_c0_brcm_config_0(BIT(23));
+		set_c0_brcm_cmt_ctrl(BIT(15));
+		break;
+
+	case CPU_BMIPS5000:
+		/* enable RDHWR, BRDHWR */
+		set_c0_brcm_config(BIT(17) | BIT(21));
+
+		/* Disable JTB */
+		__asm__ __volatile__(
+		"	.set	noreorder\n"
+		"	li	$8, 0x5a455048\n"
+		"	.word	0x4088b00f\n"	/* mtc0	t0, $22, 15 */
+		"	.word	0x4008b008\n"	/* mfc0	t0, $22, 8 */
+		"	li	$9, 0x00008000\n"
+		"	or	$8, $8, $9\n"
+		"	.word	0x4088b008\n"	/* mtc0	t0, $22, 8 */
+		"	sync\n"
+		"	li	$8, 0x0\n"
+		"	.word	0x4088b00f\n"	/* mtc0	t0, $22, 15 */
+		"	.set	reorder\n"
+		: : : "$8", "$9");
+
+		/* XI enable */
+		set_c0_brcm_config(BIT(27));
+
+		/* enable MIPS32R2 ROR instruction for XI TLB handlers */
+		__asm__ __volatile__(
+		"	li	$8, 0x5a455048\n"
+		"	.word	0x4088b00f\n"	/* mtc0 $8, $22, 15 */
+		"	nop; nop; nop\n"
+		"	.word	0x4008b008\n"	/* mfc0 $8, $22, 8 */
+		"	lui	$9, 0x0100\n"
+		"	or	$8, $9\n"
+		"	.word	0x4088b008\n"	/* mtc0 $8, $22, 8 */
+		: : : "$8", "$9");
+		break;
+	}
+}
diff --git a/arch/mips/kernel/smp-cmp.c b/arch/mips/kernel/smp-cmp.c
new file mode 100644
index 000000000..76f5824cd
--- /dev/null
+++ b/arch/mips/kernel/smp-cmp.c
@@ -0,0 +1,148 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ * Copyright (C) 2007 MIPS Technologies, Inc.
+ *    Chris Dearman (chris@mips.com)
+ */
+
+#undef DEBUG
+
+#include <linux/kernel.h>
+#include <linux/sched/task_stack.h>
+#include <linux/smp.h>
+#include <linux/cpumask.h>
+#include <linux/interrupt.h>
+#include <linux/compiler.h>
+
+#include <linux/atomic.h>
+#include <asm/cacheflush.h>
+#include <asm/cpu.h>
+#include <asm/processor.h>
+#include <asm/hardirq.h>
+#include <asm/mmu_context.h>
+#include <asm/smp.h>
+#include <asm/time.h>
+#include <asm/mipsregs.h>
+#include <asm/mipsmtregs.h>
+#include <asm/mips_mt.h>
+#include <asm/amon.h>
+
+static void cmp_init_secondary(void)
+{
+	struct cpuinfo_mips *c __maybe_unused = &current_cpu_data;
+
+	/* Assume GIC is present */
+	change_c0_status(ST0_IM, STATUSF_IP2 | STATUSF_IP3 | STATUSF_IP4 |
+				 STATUSF_IP5 | STATUSF_IP6 | STATUSF_IP7);
+
+	/* Enable per-cpu interrupts: platform specific */
+
+#ifdef CONFIG_MIPS_MT_SMP
+	if (cpu_has_mipsmt)
+		cpu_set_vpe_id(c, (read_c0_tcbind() >> TCBIND_CURVPE_SHIFT) &
+				  TCBIND_CURVPE);
+#endif
+}
+
+static void cmp_smp_finish(void)
+{
+	pr_debug("SMPCMP: CPU%d: %s\n", smp_processor_id(), __func__);
+
+	/* CDFIXME: remove this? */
+	write_c0_compare(read_c0_count() + (8 * mips_hpt_frequency / HZ));
+
+#ifdef CONFIG_MIPS_MT_FPAFF
+	/* If we have an FPU, enroll ourselves in the FPU-full mask */
+	if (cpu_has_fpu)
+		cpumask_set_cpu(smp_processor_id(), &mt_fpu_cpumask);
+#endif /* CONFIG_MIPS_MT_FPAFF */
+
+	local_irq_enable();
+}
+
+/*
+ * Setup the PC, SP, and GP of a secondary processor and start it running
+ * smp_bootstrap is the place to resume from
+ * __KSTK_TOS(idle) is apparently the stack pointer
+ * (unsigned long)idle->thread_info the gp
+ */
+static int cmp_boot_secondary(int cpu, struct task_struct *idle)
+{
+	struct thread_info *gp = task_thread_info(idle);
+	unsigned long sp = __KSTK_TOS(idle);
+	unsigned long pc = (unsigned long)&smp_bootstrap;
+	unsigned long a0 = 0;
+
+	pr_debug("SMPCMP: CPU%d: %s cpu %d\n", smp_processor_id(),
+		__func__, cpu);
+
+#if 0
+	/* Needed? */
+	flush_icache_range((unsigned long)gp,
+			   (unsigned long)(gp + sizeof(struct thread_info)));
+#endif
+
+	amon_cpu_start(cpu, pc, sp, (unsigned long)gp, a0);
+	return 0;
+}
+
+/*
+ * Common setup before any secondaries are started
+ */
+void __init cmp_smp_setup(void)
+{
+	int i;
+	int ncpu = 0;
+
+	pr_debug("SMPCMP: CPU%d: %s\n", smp_processor_id(), __func__);
+
+#ifdef CONFIG_MIPS_MT_FPAFF
+	/* If we have an FPU, enroll ourselves in the FPU-full mask */
+	if (cpu_has_fpu)
+		cpumask_set_cpu(0, &mt_fpu_cpumask);
+#endif /* CONFIG_MIPS_MT_FPAFF */
+
+	for (i = 1; i < NR_CPUS; i++) {
+		if (amon_cpu_avail(i)) {
+			set_cpu_possible(i, true);
+			__cpu_number_map[i]	= ++ncpu;
+			__cpu_logical_map[ncpu] = i;
+		}
+	}
+
+	if (cpu_has_mipsmt) {
+		unsigned int nvpe = 1;
+#ifdef CONFIG_MIPS_MT_SMP
+		unsigned int mvpconf0 = read_c0_mvpconf0();
+
+		nvpe = ((mvpconf0 & MVPCONF0_PVPE) >> MVPCONF0_PVPE_SHIFT) + 1;
+#endif
+		smp_num_siblings = nvpe;
+	}
+	pr_info("Detected %i available secondary CPU(s)\n", ncpu);
+}
+
+void __init cmp_prepare_cpus(unsigned int max_cpus)
+{
+	pr_debug("SMPCMP: CPU%d: %s max_cpus=%d\n",
+		 smp_processor_id(), __func__, max_cpus);
+
+#ifdef CONFIG_MIPS_MT
+	/*
+	 * FIXME: some of these options are per-system, some per-core and
+	 * some per-cpu
+	 */
+	mips_mt_set_cpuoptions();
+#endif
+
+}
+
+const struct plat_smp_ops cmp_smp_ops = {
+	.send_ipi_single	= mips_smp_send_ipi_single,
+	.send_ipi_mask		= mips_smp_send_ipi_mask,
+	.init_secondary		= cmp_init_secondary,
+	.smp_finish		= cmp_smp_finish,
+	.boot_secondary		= cmp_boot_secondary,
+	.smp_setup		= cmp_smp_setup,
+	.prepare_cpus		= cmp_prepare_cpus,
+};
diff --git a/arch/mips/kernel/smp-cps.c b/arch/mips/kernel/smp-cps.c
new file mode 100644
index 000000000..bcd6a944b
--- /dev/null
+++ b/arch/mips/kernel/smp-cps.c
@@ -0,0 +1,644 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2013 Imagination Technologies
+ * Author: Paul Burton <paul.burton@mips.com>
+ */
+
+#include <linux/cpu.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/sched/task_stack.h>
+#include <linux/sched/hotplug.h>
+#include <linux/slab.h>
+#include <linux/smp.h>
+#include <linux/types.h>
+#include <linux/irq.h>
+
+#include <asm/bcache.h>
+#include <asm/mips-cps.h>
+#include <asm/mips_mt.h>
+#include <asm/mipsregs.h>
+#include <asm/pm-cps.h>
+#include <asm/r4kcache.h>
+#include <asm/smp-cps.h>
+#include <asm/time.h>
+#include <asm/uasm.h>
+
+static bool threads_disabled;
+static DECLARE_BITMAP(core_power, NR_CPUS);
+
+struct core_boot_config *mips_cps_core_bootcfg;
+
+static int __init setup_nothreads(char *s)
+{
+	threads_disabled = true;
+	return 0;
+}
+early_param("nothreads", setup_nothreads);
+
+static unsigned core_vpe_count(unsigned int cluster, unsigned core)
+{
+	if (threads_disabled)
+		return 1;
+
+	return mips_cps_numvps(cluster, core);
+}
+
+static void __init cps_smp_setup(void)
+{
+	unsigned int nclusters, ncores, nvpes, core_vpes;
+	unsigned long core_entry;
+	int cl, c, v;
+
+	/* Detect & record VPE topology */
+	nvpes = 0;
+	nclusters = mips_cps_numclusters();
+	pr_info("%s topology ", cpu_has_mips_r6 ? "VP" : "VPE");
+	for (cl = 0; cl < nclusters; cl++) {
+		if (cl > 0)
+			pr_cont(",");
+		pr_cont("{");
+
+		ncores = mips_cps_numcores(cl);
+		for (c = 0; c < ncores; c++) {
+			core_vpes = core_vpe_count(cl, c);
+
+			if (c > 0)
+				pr_cont(",");
+			pr_cont("%u", core_vpes);
+
+			/* Use the number of VPEs in cluster 0 core 0 for smp_num_siblings */
+			if (!cl && !c)
+				smp_num_siblings = core_vpes;
+
+			for (v = 0; v < min_t(int, core_vpes, NR_CPUS - nvpes); v++) {
+				cpu_set_cluster(&cpu_data[nvpes + v], cl);
+				cpu_set_core(&cpu_data[nvpes + v], c);
+				cpu_set_vpe_id(&cpu_data[nvpes + v], v);
+			}
+
+			nvpes += core_vpes;
+		}
+
+		pr_cont("}");
+	}
+	pr_cont(" total %u\n", nvpes);
+
+	/* Indicate present CPUs (CPU being synonymous with VPE) */
+	for (v = 0; v < min_t(unsigned, nvpes, NR_CPUS); v++) {
+		set_cpu_possible(v, cpu_cluster(&cpu_data[v]) == 0);
+		set_cpu_present(v, cpu_cluster(&cpu_data[v]) == 0);
+		__cpu_number_map[v] = v;
+		__cpu_logical_map[v] = v;
+	}
+
+	/* Set a coherent default CCA (CWB) */
+	change_c0_config(CONF_CM_CMASK, 0x5);
+
+	/* Core 0 is powered up (we're running on it) */
+	bitmap_set(core_power, 0, 1);
+
+	/* Initialise core 0 */
+	mips_cps_core_init();
+
+	/* Make core 0 coherent with everything */
+	write_gcr_cl_coherence(0xff);
+
+	if (mips_cm_revision() >= CM_REV_CM3) {
+		core_entry = CKSEG1ADDR((unsigned long)mips_cps_core_entry);
+		write_gcr_bev_base(core_entry);
+	}
+
+#ifdef CONFIG_MIPS_MT_FPAFF
+	/* If we have an FPU, enroll ourselves in the FPU-full mask */
+	if (cpu_has_fpu)
+		cpumask_set_cpu(0, &mt_fpu_cpumask);
+#endif /* CONFIG_MIPS_MT_FPAFF */
+}
+
+static void __init cps_prepare_cpus(unsigned int max_cpus)
+{
+	unsigned ncores, core_vpes, c, cca;
+	bool cca_unsuitable, cores_limited;
+	u32 *entry_code;
+
+	mips_mt_set_cpuoptions();
+
+	/* Detect whether the CCA is unsuited to multi-core SMP */
+	cca = read_c0_config() & CONF_CM_CMASK;
+	switch (cca) {
+	case 0x4: /* CWBE */
+	case 0x5: /* CWB */
+		/* The CCA is coherent, multi-core is fine */
+		cca_unsuitable = false;
+		break;
+
+	default:
+		/* CCA is not coherent, multi-core is not usable */
+		cca_unsuitable = true;
+	}
+
+	/* Warn the user if the CCA prevents multi-core */
+	cores_limited = false;
+	if (cca_unsuitable || cpu_has_dc_aliases) {
+		for_each_present_cpu(c) {
+			if (cpus_are_siblings(smp_processor_id(), c))
+				continue;
+
+			set_cpu_present(c, false);
+			cores_limited = true;
+		}
+	}
+	if (cores_limited)
+		pr_warn("Using only one core due to %s%s%s\n",
+			cca_unsuitable ? "unsuitable CCA" : "",
+			(cca_unsuitable && cpu_has_dc_aliases) ? " & " : "",
+			cpu_has_dc_aliases ? "dcache aliasing" : "");
+
+	/*
+	 * Patch the start of mips_cps_core_entry to provide:
+	 *
+	 * s0 = kseg0 CCA
+	 */
+	entry_code = (u32 *)&mips_cps_core_entry;
+	uasm_i_addiu(&entry_code, 16, 0, cca);
+	blast_dcache_range((unsigned long)&mips_cps_core_entry,
+			   (unsigned long)entry_code);
+	bc_wback_inv((unsigned long)&mips_cps_core_entry,
+		     (void *)entry_code - (void *)&mips_cps_core_entry);
+	__sync();
+
+	/* Allocate core boot configuration structs */
+	ncores = mips_cps_numcores(0);
+	mips_cps_core_bootcfg = kcalloc(ncores, sizeof(*mips_cps_core_bootcfg),
+					GFP_KERNEL);
+	if (!mips_cps_core_bootcfg) {
+		pr_err("Failed to allocate boot config for %u cores\n", ncores);
+		goto err_out;
+	}
+
+	/* Allocate VPE boot configuration structs */
+	for (c = 0; c < ncores; c++) {
+		core_vpes = core_vpe_count(0, c);
+		mips_cps_core_bootcfg[c].vpe_config = kcalloc(core_vpes,
+				sizeof(*mips_cps_core_bootcfg[c].vpe_config),
+				GFP_KERNEL);
+		if (!mips_cps_core_bootcfg[c].vpe_config) {
+			pr_err("Failed to allocate %u VPE boot configs\n",
+			       core_vpes);
+			goto err_out;
+		}
+	}
+
+	/* Mark this CPU as booted */
+	atomic_set(&mips_cps_core_bootcfg[cpu_core(&current_cpu_data)].vpe_mask,
+		   1 << cpu_vpe_id(&current_cpu_data));
+
+	return;
+err_out:
+	/* Clean up allocations */
+	if (mips_cps_core_bootcfg) {
+		for (c = 0; c < ncores; c++)
+			kfree(mips_cps_core_bootcfg[c].vpe_config);
+		kfree(mips_cps_core_bootcfg);
+		mips_cps_core_bootcfg = NULL;
+	}
+
+	/* Effectively disable SMP by declaring CPUs not present */
+	for_each_possible_cpu(c) {
+		if (c == 0)
+			continue;
+		set_cpu_present(c, false);
+	}
+}
+
+static void boot_core(unsigned int core, unsigned int vpe_id)
+{
+	u32 stat, seq_state;
+	unsigned timeout;
+
+	/* Select the appropriate core */
+	mips_cm_lock_other(0, core, 0, CM_GCR_Cx_OTHER_BLOCK_LOCAL);
+
+	/* Set its reset vector */
+	write_gcr_co_reset_base(CKSEG1ADDR((unsigned long)mips_cps_core_entry));
+
+	/* Ensure its coherency is disabled */
+	write_gcr_co_coherence(0);
+
+	/* Start it with the legacy memory map and exception base */
+	write_gcr_co_reset_ext_base(CM_GCR_Cx_RESET_EXT_BASE_UEB);
+
+	/* Ensure the core can access the GCRs */
+	set_gcr_access(1 << core);
+
+	if (mips_cpc_present()) {
+		/* Reset the core */
+		mips_cpc_lock_other(core);
+
+		if (mips_cm_revision() >= CM_REV_CM3) {
+			/* Run only the requested VP following the reset */
+			write_cpc_co_vp_stop(0xf);
+			write_cpc_co_vp_run(1 << vpe_id);
+
+			/*
+			 * Ensure that the VP_RUN register is written before the
+			 * core leaves reset.
+			 */
+			wmb();
+		}
+
+		write_cpc_co_cmd(CPC_Cx_CMD_RESET);
+
+		timeout = 100;
+		while (true) {
+			stat = read_cpc_co_stat_conf();
+			seq_state = stat & CPC_Cx_STAT_CONF_SEQSTATE;
+			seq_state >>= __ffs(CPC_Cx_STAT_CONF_SEQSTATE);
+
+			/* U6 == coherent execution, ie. the core is up */
+			if (seq_state == CPC_Cx_STAT_CONF_SEQSTATE_U6)
+				break;
+
+			/* Delay a little while before we start warning */
+			if (timeout) {
+				timeout--;
+				mdelay(10);
+				continue;
+			}
+
+			pr_warn("Waiting for core %u to start... STAT_CONF=0x%x\n",
+				core, stat);
+			mdelay(1000);
+		}
+
+		mips_cpc_unlock_other();
+	} else {
+		/* Take the core out of reset */
+		write_gcr_co_reset_release(0);
+	}
+
+	mips_cm_unlock_other();
+
+	/* The core is now powered up */
+	bitmap_set(core_power, core, 1);
+}
+
+static void remote_vpe_boot(void *dummy)
+{
+	unsigned core = cpu_core(&current_cpu_data);
+	struct core_boot_config *core_cfg = &mips_cps_core_bootcfg[core];
+
+	mips_cps_boot_vpes(core_cfg, cpu_vpe_id(&current_cpu_data));
+}
+
+static int cps_boot_secondary(int cpu, struct task_struct *idle)
+{
+	unsigned core = cpu_core(&cpu_data[cpu]);
+	unsigned vpe_id = cpu_vpe_id(&cpu_data[cpu]);
+	struct core_boot_config *core_cfg = &mips_cps_core_bootcfg[core];
+	struct vpe_boot_config *vpe_cfg = &core_cfg->vpe_config[vpe_id];
+	unsigned long core_entry;
+	unsigned int remote;
+	int err;
+
+	/* We don't yet support booting CPUs in other clusters */
+	if (cpu_cluster(&cpu_data[cpu]) != cpu_cluster(&raw_current_cpu_data))
+		return -ENOSYS;
+
+	vpe_cfg->pc = (unsigned long)&smp_bootstrap;
+	vpe_cfg->sp = __KSTK_TOS(idle);
+	vpe_cfg->gp = (unsigned long)task_thread_info(idle);
+
+	atomic_or(1 << cpu_vpe_id(&cpu_data[cpu]), &core_cfg->vpe_mask);
+
+	preempt_disable();
+
+	if (!test_bit(core, core_power)) {
+		/* Boot a VPE on a powered down core */
+		boot_core(core, vpe_id);
+		goto out;
+	}
+
+	if (cpu_has_vp) {
+		mips_cm_lock_other(0, core, vpe_id, CM_GCR_Cx_OTHER_BLOCK_LOCAL);
+		core_entry = CKSEG1ADDR((unsigned long)mips_cps_core_entry);
+		write_gcr_co_reset_base(core_entry);
+		mips_cm_unlock_other();
+	}
+
+	if (!cpus_are_siblings(cpu, smp_processor_id())) {
+		/* Boot a VPE on another powered up core */
+		for (remote = 0; remote < NR_CPUS; remote++) {
+			if (!cpus_are_siblings(cpu, remote))
+				continue;
+			if (cpu_online(remote))
+				break;
+		}
+		if (remote >= NR_CPUS) {
+			pr_crit("No online CPU in core %u to start CPU%d\n",
+				core, cpu);
+			goto out;
+		}
+
+		err = smp_call_function_single(remote, remote_vpe_boot,
+					       NULL, 1);
+		if (err)
+			panic("Failed to call remote CPU\n");
+		goto out;
+	}
+
+	BUG_ON(!cpu_has_mipsmt && !cpu_has_vp);
+
+	/* Boot a VPE on this core */
+	mips_cps_boot_vpes(core_cfg, vpe_id);
+out:
+	preempt_enable();
+	return 0;
+}
+
+static void cps_init_secondary(void)
+{
+	/* Disable MT - we only want to run 1 TC per VPE */
+	if (cpu_has_mipsmt)
+		dmt();
+
+	if (mips_cm_revision() >= CM_REV_CM3) {
+		unsigned int ident = read_gic_vl_ident();
+
+		/*
+		 * Ensure that our calculation of the VP ID matches up with
+		 * what the GIC reports, otherwise we'll have configured
+		 * interrupts incorrectly.
+		 */
+		BUG_ON(ident != mips_cm_vp_id(smp_processor_id()));
+	}
+
+	if (cpu_has_veic)
+		clear_c0_status(ST0_IM);
+	else
+		change_c0_status(ST0_IM, STATUSF_IP2 | STATUSF_IP3 |
+					 STATUSF_IP4 | STATUSF_IP5 |
+					 STATUSF_IP6 | STATUSF_IP7);
+}
+
+static void cps_smp_finish(void)
+{
+	write_c0_compare(read_c0_count() + (8 * mips_hpt_frequency / HZ));
+
+#ifdef CONFIG_MIPS_MT_FPAFF
+	/* If we have an FPU, enroll ourselves in the FPU-full mask */
+	if (cpu_has_fpu)
+		cpumask_set_cpu(smp_processor_id(), &mt_fpu_cpumask);
+#endif /* CONFIG_MIPS_MT_FPAFF */
+
+	local_irq_enable();
+}
+
+#if defined(CONFIG_HOTPLUG_CPU) || defined(CONFIG_KEXEC)
+
+enum cpu_death {
+	CPU_DEATH_HALT,
+	CPU_DEATH_POWER,
+};
+
+static void cps_shutdown_this_cpu(enum cpu_death death)
+{
+	unsigned int cpu, core, vpe_id;
+
+	cpu = smp_processor_id();
+	core = cpu_core(&cpu_data[cpu]);
+
+	if (death == CPU_DEATH_HALT) {
+		vpe_id = cpu_vpe_id(&cpu_data[cpu]);
+
+		pr_debug("Halting core %d VP%d\n", core, vpe_id);
+		if (cpu_has_mipsmt) {
+			/* Halt this TC */
+			write_c0_tchalt(TCHALT_H);
+			instruction_hazard();
+		} else if (cpu_has_vp) {
+			write_cpc_cl_vp_stop(1 << vpe_id);
+
+			/* Ensure that the VP_STOP register is written */
+			wmb();
+		}
+	} else {
+		pr_debug("Gating power to core %d\n", core);
+		/* Power down the core */
+		cps_pm_enter_state(CPS_PM_POWER_GATED);
+	}
+}
+
+#ifdef CONFIG_KEXEC
+
+static void cps_kexec_nonboot_cpu(void)
+{
+	if (cpu_has_mipsmt || cpu_has_vp)
+		cps_shutdown_this_cpu(CPU_DEATH_HALT);
+	else
+		cps_shutdown_this_cpu(CPU_DEATH_POWER);
+}
+
+#endif /* CONFIG_KEXEC */
+
+#endif /* CONFIG_HOTPLUG_CPU || CONFIG_KEXEC */
+
+#ifdef CONFIG_HOTPLUG_CPU
+
+static int cps_cpu_disable(void)
+{
+	unsigned cpu = smp_processor_id();
+	struct core_boot_config *core_cfg;
+
+	if (!cps_pm_support_state(CPS_PM_POWER_GATED))
+		return -EINVAL;
+
+	core_cfg = &mips_cps_core_bootcfg[cpu_core(&current_cpu_data)];
+	atomic_sub(1 << cpu_vpe_id(&current_cpu_data), &core_cfg->vpe_mask);
+	smp_mb__after_atomic();
+	set_cpu_online(cpu, false);
+	calculate_cpu_foreign_map();
+	irq_migrate_all_off_this_cpu();
+
+	return 0;
+}
+
+static unsigned cpu_death_sibling;
+static enum cpu_death cpu_death;
+
+void play_dead(void)
+{
+	unsigned int cpu;
+
+	local_irq_disable();
+	idle_task_exit();
+	cpu = smp_processor_id();
+	cpu_death = CPU_DEATH_POWER;
+
+	pr_debug("CPU%d going offline\n", cpu);
+
+	if (cpu_has_mipsmt || cpu_has_vp) {
+		/* Look for another online VPE within the core */
+		for_each_online_cpu(cpu_death_sibling) {
+			if (!cpus_are_siblings(cpu, cpu_death_sibling))
+				continue;
+
+			/*
+			 * There is an online VPE within the core. Just halt
+			 * this TC and leave the core alone.
+			 */
+			cpu_death = CPU_DEATH_HALT;
+			break;
+		}
+	}
+
+	/* This CPU has chosen its way out */
+	(void)cpu_report_death();
+
+	cps_shutdown_this_cpu(cpu_death);
+
+	/* This should never be reached */
+	panic("Failed to offline CPU %u", cpu);
+}
+
+static void wait_for_sibling_halt(void *ptr_cpu)
+{
+	unsigned cpu = (unsigned long)ptr_cpu;
+	unsigned vpe_id = cpu_vpe_id(&cpu_data[cpu]);
+	unsigned halted;
+	unsigned long flags;
+
+	do {
+		local_irq_save(flags);
+		settc(vpe_id);
+		halted = read_tc_c0_tchalt();
+		local_irq_restore(flags);
+	} while (!(halted & TCHALT_H));
+}
+
+static void cps_cpu_die(unsigned int cpu)
+{
+	unsigned core = cpu_core(&cpu_data[cpu]);
+	unsigned int vpe_id = cpu_vpe_id(&cpu_data[cpu]);
+	ktime_t fail_time;
+	unsigned stat;
+	int err;
+
+	/* Wait for the cpu to choose its way out */
+	if (!cpu_wait_death(cpu, 5)) {
+		pr_err("CPU%u: didn't offline\n", cpu);
+		return;
+	}
+
+	/*
+	 * Now wait for the CPU to actually offline. Without doing this that
+	 * offlining may race with one or more of:
+	 *
+	 *   - Onlining the CPU again.
+	 *   - Powering down the core if another VPE within it is offlined.
+	 *   - A sibling VPE entering a non-coherent state.
+	 *
+	 * In the non-MT halt case (ie. infinite loop) the CPU is doing nothing
+	 * with which we could race, so do nothing.
+	 */
+	if (cpu_death == CPU_DEATH_POWER) {
+		/*
+		 * Wait for the core to enter a powered down or clock gated
+		 * state, the latter happening when a JTAG probe is connected
+		 * in which case the CPC will refuse to power down the core.
+		 */
+		fail_time = ktime_add_ms(ktime_get(), 2000);
+		do {
+			mips_cm_lock_other(0, core, 0, CM_GCR_Cx_OTHER_BLOCK_LOCAL);
+			mips_cpc_lock_other(core);
+			stat = read_cpc_co_stat_conf();
+			stat &= CPC_Cx_STAT_CONF_SEQSTATE;
+			stat >>= __ffs(CPC_Cx_STAT_CONF_SEQSTATE);
+			mips_cpc_unlock_other();
+			mips_cm_unlock_other();
+
+			if (stat == CPC_Cx_STAT_CONF_SEQSTATE_D0 ||
+			    stat == CPC_Cx_STAT_CONF_SEQSTATE_D2 ||
+			    stat == CPC_Cx_STAT_CONF_SEQSTATE_U2)
+				break;
+
+			/*
+			 * The core ought to have powered down, but didn't &
+			 * now we don't really know what state it's in. It's
+			 * likely that its _pwr_up pin has been wired to logic
+			 * 1 & it powered back up as soon as we powered it
+			 * down...
+			 *
+			 * The best we can do is warn the user & continue in
+			 * the hope that the core is doing nothing harmful &
+			 * might behave properly if we online it later.
+			 */
+			if (WARN(ktime_after(ktime_get(), fail_time),
+				 "CPU%u hasn't powered down, seq. state %u\n",
+				 cpu, stat))
+				break;
+		} while (1);
+
+		/* Indicate the core is powered off */
+		bitmap_clear(core_power, core, 1);
+	} else if (cpu_has_mipsmt) {
+		/*
+		 * Have a CPU with access to the offlined CPUs registers wait
+		 * for its TC to halt.
+		 */
+		err = smp_call_function_single(cpu_death_sibling,
+					       wait_for_sibling_halt,
+					       (void *)(unsigned long)cpu, 1);
+		if (err)
+			panic("Failed to call remote sibling CPU\n");
+	} else if (cpu_has_vp) {
+		do {
+			mips_cm_lock_other(0, core, vpe_id, CM_GCR_Cx_OTHER_BLOCK_LOCAL);
+			stat = read_cpc_co_vp_running();
+			mips_cm_unlock_other();
+		} while (stat & (1 << vpe_id));
+	}
+}
+
+#endif /* CONFIG_HOTPLUG_CPU */
+
+static const struct plat_smp_ops cps_smp_ops = {
+	.smp_setup		= cps_smp_setup,
+	.prepare_cpus		= cps_prepare_cpus,
+	.boot_secondary		= cps_boot_secondary,
+	.init_secondary		= cps_init_secondary,
+	.smp_finish		= cps_smp_finish,
+	.send_ipi_single	= mips_smp_send_ipi_single,
+	.send_ipi_mask		= mips_smp_send_ipi_mask,
+#ifdef CONFIG_HOTPLUG_CPU
+	.cpu_disable		= cps_cpu_disable,
+	.cpu_die		= cps_cpu_die,
+#endif
+#ifdef CONFIG_KEXEC
+	.kexec_nonboot_cpu	= cps_kexec_nonboot_cpu,
+#endif
+};
+
+bool mips_cps_smp_in_use(void)
+{
+	extern const struct plat_smp_ops *mp_ops;
+	return mp_ops == &cps_smp_ops;
+}
+
+int register_cps_smp_ops(void)
+{
+	if (!mips_cm_present()) {
+		pr_warn("MIPS CPS SMP unable to proceed without a CM\n");
+		return -ENODEV;
+	}
+
+	/* check we have a GIC - we need one for IPIs */
+	if (!(read_gcr_gic_status() & CM_GCR_GIC_STATUS_EX)) {
+		pr_warn("MIPS CPS SMP unable to proceed without a GIC\n");
+		return -ENODEV;
+	}
+
+	register_smp_ops(&cps_smp_ops);
+	return 0;
+}
diff --git a/arch/mips/kernel/smp-mt.c b/arch/mips/kernel/smp-mt.c
new file mode 100644
index 000000000..5f04a0141
--- /dev/null
+++ b/arch/mips/kernel/smp-mt.c
@@ -0,0 +1,240 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ * Copyright (C) 2004, 05, 06 MIPS Technologies, Inc.
+ *    Elizabeth Clarke (beth@mips.com)
+ *    Ralf Baechle (ralf@linux-mips.org)
+ * Copyright (C) 2006 Ralf Baechle (ralf@linux-mips.org)
+ */
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/cpumask.h>
+#include <linux/interrupt.h>
+#include <linux/compiler.h>
+#include <linux/sched/task_stack.h>
+#include <linux/smp.h>
+
+#include <linux/atomic.h>
+#include <asm/cacheflush.h>
+#include <asm/cpu.h>
+#include <asm/processor.h>
+#include <asm/hardirq.h>
+#include <asm/mmu_context.h>
+#include <asm/time.h>
+#include <asm/mipsregs.h>
+#include <asm/mipsmtregs.h>
+#include <asm/mips_mt.h>
+#include <asm/mips-cps.h>
+
+static void __init smvp_copy_vpe_config(void)
+{
+	write_vpe_c0_status(
+		(read_c0_status() & ~(ST0_IM | ST0_IE | ST0_KSU)) | ST0_CU0);
+
+	/* set config to be the same as vpe0, particularly kseg0 coherency alg */
+	write_vpe_c0_config( read_c0_config());
+
+	/* make sure there are no software interrupts pending */
+	write_vpe_c0_cause(0);
+
+	/* Propagate Config7 */
+	write_vpe_c0_config7(read_c0_config7());
+
+	write_vpe_c0_count(read_c0_count());
+}
+
+static unsigned int __init smvp_vpe_init(unsigned int tc, unsigned int mvpconf0,
+	unsigned int ncpu)
+{
+	if (tc > ((mvpconf0 & MVPCONF0_PVPE) >> MVPCONF0_PVPE_SHIFT))
+		return ncpu;
+
+	/* Deactivate all but VPE 0 */
+	if (tc != 0) {
+		unsigned long tmp = read_vpe_c0_vpeconf0();
+
+		tmp &= ~VPECONF0_VPA;
+
+		/* master VPE */
+		tmp |= VPECONF0_MVP;
+		write_vpe_c0_vpeconf0(tmp);
+
+		/* Record this as available CPU */
+		set_cpu_possible(tc, true);
+		set_cpu_present(tc, true);
+		__cpu_number_map[tc]	= ++ncpu;
+		__cpu_logical_map[ncpu] = tc;
+	}
+
+	/* Disable multi-threading with TC's */
+	write_vpe_c0_vpecontrol(read_vpe_c0_vpecontrol() & ~VPECONTROL_TE);
+
+	if (tc != 0)
+		smvp_copy_vpe_config();
+
+	cpu_set_vpe_id(&cpu_data[ncpu], tc);
+
+	return ncpu;
+}
+
+static void __init smvp_tc_init(unsigned int tc, unsigned int mvpconf0)
+{
+	unsigned long tmp;
+
+	if (!tc)
+		return;
+
+	/* bind a TC to each VPE, May as well put all excess TC's
+	   on the last VPE */
+	if (tc >= (((mvpconf0 & MVPCONF0_PVPE) >> MVPCONF0_PVPE_SHIFT)+1))
+		write_tc_c0_tcbind(read_tc_c0_tcbind() | ((mvpconf0 & MVPCONF0_PVPE) >> MVPCONF0_PVPE_SHIFT));
+	else {
+		write_tc_c0_tcbind(read_tc_c0_tcbind() | tc);
+
+		/* and set XTC */
+		write_vpe_c0_vpeconf0(read_vpe_c0_vpeconf0() | (tc << VPECONF0_XTC_SHIFT));
+	}
+
+	tmp = read_tc_c0_tcstatus();
+
+	/* mark not allocated and not dynamically allocatable */
+	tmp &= ~(TCSTATUS_A | TCSTATUS_DA);
+	tmp |= TCSTATUS_IXMT;		/* interrupt exempt */
+	write_tc_c0_tcstatus(tmp);
+
+	write_tc_c0_tchalt(TCHALT_H);
+}
+
+static void vsmp_init_secondary(void)
+{
+	/* This is Malta specific: IPI,performance and timer interrupts */
+	if (mips_gic_present())
+		change_c0_status(ST0_IM, STATUSF_IP2 | STATUSF_IP3 |
+					 STATUSF_IP4 | STATUSF_IP5 |
+					 STATUSF_IP6 | STATUSF_IP7);
+	else
+		change_c0_status(ST0_IM, STATUSF_IP0 | STATUSF_IP1 |
+					 STATUSF_IP6 | STATUSF_IP7);
+}
+
+static void vsmp_smp_finish(void)
+{
+	/* CDFIXME: remove this? */
+	write_c0_compare(read_c0_count() + (8* mips_hpt_frequency/HZ));
+
+#ifdef CONFIG_MIPS_MT_FPAFF
+	/* If we have an FPU, enroll ourselves in the FPU-full mask */
+	if (cpu_has_fpu)
+		cpumask_set_cpu(smp_processor_id(), &mt_fpu_cpumask);
+#endif /* CONFIG_MIPS_MT_FPAFF */
+
+	local_irq_enable();
+}
+
+/*
+ * Setup the PC, SP, and GP of a secondary processor and start it
+ * running!
+ * smp_bootstrap is the place to resume from
+ * __KSTK_TOS(idle) is apparently the stack pointer
+ * (unsigned long)idle->thread_info the gp
+ * assumes a 1:1 mapping of TC => VPE
+ */
+static int vsmp_boot_secondary(int cpu, struct task_struct *idle)
+{
+	struct thread_info *gp = task_thread_info(idle);
+	dvpe();
+	set_c0_mvpcontrol(MVPCONTROL_VPC);
+
+	settc(cpu);
+
+	/* restart */
+	write_tc_c0_tcrestart((unsigned long)&smp_bootstrap);
+
+	/* enable the tc this vpe/cpu will be running */
+	write_tc_c0_tcstatus((read_tc_c0_tcstatus() & ~TCSTATUS_IXMT) | TCSTATUS_A);
+
+	write_tc_c0_tchalt(0);
+
+	/* enable the VPE */
+	write_vpe_c0_vpeconf0(read_vpe_c0_vpeconf0() | VPECONF0_VPA);
+
+	/* stack pointer */
+	write_tc_gpr_sp( __KSTK_TOS(idle));
+
+	/* global pointer */
+	write_tc_gpr_gp((unsigned long)gp);
+
+	flush_icache_range((unsigned long)gp,
+			   (unsigned long)(gp + sizeof(struct thread_info)));
+
+	/* finally out of configuration and into chaos */
+	clear_c0_mvpcontrol(MVPCONTROL_VPC);
+
+	evpe(EVPE_ENABLE);
+
+	return 0;
+}
+
+/*
+ * Common setup before any secondaries are started
+ * Make sure all CPU's are in a sensible state before we boot any of the
+ * secondaries
+ */
+static void __init vsmp_smp_setup(void)
+{
+	unsigned int mvpconf0, ntc, tc, ncpu = 0;
+	unsigned int nvpe;
+
+#ifdef CONFIG_MIPS_MT_FPAFF
+	/* If we have an FPU, enroll ourselves in the FPU-full mask */
+	if (cpu_has_fpu)
+		cpumask_set_cpu(0, &mt_fpu_cpumask);
+#endif /* CONFIG_MIPS_MT_FPAFF */
+	if (!cpu_has_mipsmt)
+		return;
+
+	/* disable MT so we can configure */
+	dvpe();
+	dmt();
+
+	/* Put MVPE's into 'configuration state' */
+	set_c0_mvpcontrol(MVPCONTROL_VPC);
+
+	mvpconf0 = read_c0_mvpconf0();
+	ntc = (mvpconf0 & MVPCONF0_PTC) >> MVPCONF0_PTC_SHIFT;
+
+	nvpe = ((mvpconf0 & MVPCONF0_PVPE) >> MVPCONF0_PVPE_SHIFT) + 1;
+	smp_num_siblings = nvpe;
+
+	/* we'll always have more TC's than VPE's, so loop setting everything
+	   to a sensible state */
+	for (tc = 0; tc <= ntc; tc++) {
+		settc(tc);
+
+		smvp_tc_init(tc, mvpconf0);
+		ncpu = smvp_vpe_init(tc, mvpconf0, ncpu);
+	}
+
+	/* Release config state */
+	clear_c0_mvpcontrol(MVPCONTROL_VPC);
+
+	/* We'll wait until starting the secondaries before starting MVPE */
+
+	printk(KERN_INFO "Detected %i available secondary CPU(s)\n", ncpu);
+}
+
+static void __init vsmp_prepare_cpus(unsigned int max_cpus)
+{
+	mips_mt_set_cpuoptions();
+}
+
+const struct plat_smp_ops vsmp_smp_ops = {
+	.send_ipi_single	= mips_smp_send_ipi_single,
+	.send_ipi_mask		= mips_smp_send_ipi_mask,
+	.init_secondary		= vsmp_init_secondary,
+	.smp_finish		= vsmp_smp_finish,
+	.boot_secondary		= vsmp_boot_secondary,
+	.smp_setup		= vsmp_smp_setup,
+	.prepare_cpus		= vsmp_prepare_cpus,
+};
+
diff --git a/arch/mips/kernel/smp-up.c b/arch/mips/kernel/smp-up.c
new file mode 100644
index 000000000..525d3196f
--- /dev/null
+++ b/arch/mips/kernel/smp-up.c
@@ -0,0 +1,79 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2006, 07 by Ralf Baechle (ralf@linux-mips.org)
+ *
+ * Symmetric Uniprocessor (TM) Support
+ */
+#include <linux/kernel.h>
+#include <linux/sched.h>
+
+/*
+ * Send inter-processor interrupt
+ */
+static void up_send_ipi_single(int cpu, unsigned int action)
+{
+	panic(KERN_ERR "%s called", __func__);
+}
+
+static inline void up_send_ipi_mask(const struct cpumask *mask,
+				    unsigned int action)
+{
+	panic(KERN_ERR "%s called", __func__);
+}
+
+/*
+ *  After we've done initial boot, this function is called to allow the
+ *  board code to clean up state, if needed
+ */
+static void up_init_secondary(void)
+{
+}
+
+static void up_smp_finish(void)
+{
+}
+
+/*
+ * Firmware CPU startup hook
+ */
+static int up_boot_secondary(int cpu, struct task_struct *idle)
+{
+	return 0;
+}
+
+static void __init up_smp_setup(void)
+{
+}
+
+static void __init up_prepare_cpus(unsigned int max_cpus)
+{
+}
+
+#ifdef CONFIG_HOTPLUG_CPU
+static int up_cpu_disable(void)
+{
+	return -ENOSYS;
+}
+
+static void up_cpu_die(unsigned int cpu)
+{
+	BUG();
+}
+#endif
+
+const struct plat_smp_ops up_smp_ops = {
+	.send_ipi_single	= up_send_ipi_single,
+	.send_ipi_mask		= up_send_ipi_mask,
+	.init_secondary		= up_init_secondary,
+	.smp_finish		= up_smp_finish,
+	.boot_secondary		= up_boot_secondary,
+	.smp_setup		= up_smp_setup,
+	.prepare_cpus		= up_prepare_cpus,
+#ifdef CONFIG_HOTPLUG_CPU
+	.cpu_disable		= up_cpu_disable,
+	.cpu_die		= up_cpu_die,
+#endif
+};
diff --git a/arch/mips/kernel/smp.c b/arch/mips/kernel/smp.c
new file mode 100644
index 000000000..002c91fcb
--- /dev/null
+++ b/arch/mips/kernel/smp.c
@@ -0,0 +1,714 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *
+ * Copyright (C) 2000, 2001 Kanoj Sarcar
+ * Copyright (C) 2000, 2001 Ralf Baechle
+ * Copyright (C) 2000, 2001 Silicon Graphics, Inc.
+ * Copyright (C) 2000, 2001, 2003 Broadcom Corporation
+ */
+#include <linux/cache.h>
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/smp.h>
+#include <linux/spinlock.h>
+#include <linux/threads.h>
+#include <linux/export.h>
+#include <linux/time.h>
+#include <linux/timex.h>
+#include <linux/sched/mm.h>
+#include <linux/cpumask.h>
+#include <linux/cpu.h>
+#include <linux/err.h>
+#include <linux/ftrace.h>
+#include <linux/irqdomain.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+
+#include <linux/atomic.h>
+#include <asm/cpu.h>
+#include <asm/ginvt.h>
+#include <asm/processor.h>
+#include <asm/idle.h>
+#include <asm/r4k-timer.h>
+#include <asm/mips-cps.h>
+#include <asm/mmu_context.h>
+#include <asm/time.h>
+#include <asm/setup.h>
+#include <asm/maar.h>
+
+int __cpu_number_map[CONFIG_MIPS_NR_CPU_NR_MAP];   /* Map physical to logical */
+EXPORT_SYMBOL(__cpu_number_map);
+
+int __cpu_logical_map[NR_CPUS];		/* Map logical to physical */
+EXPORT_SYMBOL(__cpu_logical_map);
+
+/* Number of TCs (or siblings in Intel speak) per CPU core */
+int smp_num_siblings = 1;
+EXPORT_SYMBOL(smp_num_siblings);
+
+/* representing the TCs (or siblings in Intel speak) of each logical CPU */
+cpumask_t cpu_sibling_map[NR_CPUS] __read_mostly;
+EXPORT_SYMBOL(cpu_sibling_map);
+
+/* representing the core map of multi-core chips of each logical CPU */
+cpumask_t cpu_core_map[NR_CPUS] __read_mostly;
+EXPORT_SYMBOL(cpu_core_map);
+
+static DECLARE_COMPLETION(cpu_starting);
+static DECLARE_COMPLETION(cpu_running);
+
+/*
+ * A logical cpu mask containing only one VPE per core to
+ * reduce the number of IPIs on large MT systems.
+ */
+cpumask_t cpu_foreign_map[NR_CPUS] __read_mostly;
+EXPORT_SYMBOL(cpu_foreign_map);
+
+/* representing cpus for which sibling maps can be computed */
+static cpumask_t cpu_sibling_setup_map;
+
+/* representing cpus for which core maps can be computed */
+static cpumask_t cpu_core_setup_map;
+
+cpumask_t cpu_coherent_mask;
+
+#ifdef CONFIG_GENERIC_IRQ_IPI
+static struct irq_desc *call_desc;
+static struct irq_desc *sched_desc;
+#endif
+
+static inline void set_cpu_sibling_map(int cpu)
+{
+	int i;
+
+	cpumask_set_cpu(cpu, &cpu_sibling_setup_map);
+
+	if (smp_num_siblings > 1) {
+		for_each_cpu(i, &cpu_sibling_setup_map) {
+			if (cpus_are_siblings(cpu, i)) {
+				cpumask_set_cpu(i, &cpu_sibling_map[cpu]);
+				cpumask_set_cpu(cpu, &cpu_sibling_map[i]);
+			}
+		}
+	} else
+		cpumask_set_cpu(cpu, &cpu_sibling_map[cpu]);
+}
+
+static inline void set_cpu_core_map(int cpu)
+{
+	int i;
+
+	cpumask_set_cpu(cpu, &cpu_core_setup_map);
+
+	for_each_cpu(i, &cpu_core_setup_map) {
+		if (cpu_data[cpu].package == cpu_data[i].package) {
+			cpumask_set_cpu(i, &cpu_core_map[cpu]);
+			cpumask_set_cpu(cpu, &cpu_core_map[i]);
+		}
+	}
+}
+
+/*
+ * Calculate a new cpu_foreign_map mask whenever a
+ * new cpu appears or disappears.
+ */
+void calculate_cpu_foreign_map(void)
+{
+	int i, k, core_present;
+	cpumask_t temp_foreign_map;
+
+	/* Re-calculate the mask */
+	cpumask_clear(&temp_foreign_map);
+	for_each_online_cpu(i) {
+		core_present = 0;
+		for_each_cpu(k, &temp_foreign_map)
+			if (cpus_are_siblings(i, k))
+				core_present = 1;
+		if (!core_present)
+			cpumask_set_cpu(i, &temp_foreign_map);
+	}
+
+	for_each_online_cpu(i)
+		cpumask_andnot(&cpu_foreign_map[i],
+			       &temp_foreign_map, &cpu_sibling_map[i]);
+}
+
+const struct plat_smp_ops *mp_ops;
+EXPORT_SYMBOL(mp_ops);
+
+void register_smp_ops(const struct plat_smp_ops *ops)
+{
+	if (mp_ops)
+		printk(KERN_WARNING "Overriding previously set SMP ops\n");
+
+	mp_ops = ops;
+}
+
+#ifdef CONFIG_GENERIC_IRQ_IPI
+void mips_smp_send_ipi_single(int cpu, unsigned int action)
+{
+	mips_smp_send_ipi_mask(cpumask_of(cpu), action);
+}
+
+void mips_smp_send_ipi_mask(const struct cpumask *mask, unsigned int action)
+{
+	unsigned long flags;
+	unsigned int core;
+	int cpu;
+
+	local_irq_save(flags);
+
+	switch (action) {
+	case SMP_CALL_FUNCTION:
+		__ipi_send_mask(call_desc, mask);
+		break;
+
+	case SMP_RESCHEDULE_YOURSELF:
+		__ipi_send_mask(sched_desc, mask);
+		break;
+
+	default:
+		BUG();
+	}
+
+	if (mips_cpc_present()) {
+		for_each_cpu(cpu, mask) {
+			if (cpus_are_siblings(cpu, smp_processor_id()))
+				continue;
+
+			core = cpu_core(&cpu_data[cpu]);
+
+			while (!cpumask_test_cpu(cpu, &cpu_coherent_mask)) {
+				mips_cm_lock_other_cpu(cpu, CM_GCR_Cx_OTHER_BLOCK_LOCAL);
+				mips_cpc_lock_other(core);
+				write_cpc_co_cmd(CPC_Cx_CMD_PWRUP);
+				mips_cpc_unlock_other();
+				mips_cm_unlock_other();
+			}
+		}
+	}
+
+	local_irq_restore(flags);
+}
+
+
+static irqreturn_t ipi_resched_interrupt(int irq, void *dev_id)
+{
+	scheduler_ipi();
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t ipi_call_interrupt(int irq, void *dev_id)
+{
+	generic_smp_call_function_interrupt();
+
+	return IRQ_HANDLED;
+}
+
+static void smp_ipi_init_one(unsigned int virq, const char *name,
+			     irq_handler_t handler)
+{
+	int ret;
+
+	irq_set_handler(virq, handle_percpu_irq);
+	ret = request_irq(virq, handler, IRQF_PERCPU, name, NULL);
+	BUG_ON(ret);
+}
+
+static unsigned int call_virq, sched_virq;
+
+int mips_smp_ipi_allocate(const struct cpumask *mask)
+{
+	int virq;
+	struct irq_domain *ipidomain;
+	struct device_node *node;
+
+	node = of_irq_find_parent(of_root);
+	ipidomain = irq_find_matching_host(node, DOMAIN_BUS_IPI);
+
+	/*
+	 * Some platforms have half DT setup. So if we found irq node but
+	 * didn't find an ipidomain, try to search for one that is not in the
+	 * DT.
+	 */
+	if (node && !ipidomain)
+		ipidomain = irq_find_matching_host(NULL, DOMAIN_BUS_IPI);
+
+	/*
+	 * There are systems which use IPI IRQ domains, but only have one
+	 * registered when some runtime condition is met. For example a Malta
+	 * kernel may include support for GIC & CPU interrupt controller IPI
+	 * IRQ domains, but if run on a system with no GIC & no MT ASE then
+	 * neither will be supported or registered.
+	 *
+	 * We only have a problem if we're actually using multiple CPUs so fail
+	 * loudly if that is the case. Otherwise simply return, skipping IPI
+	 * setup, if we're running with only a single CPU.
+	 */
+	if (!ipidomain) {
+		BUG_ON(num_present_cpus() > 1);
+		return 0;
+	}
+
+	virq = irq_reserve_ipi(ipidomain, mask);
+	BUG_ON(!virq);
+	if (!call_virq)
+		call_virq = virq;
+
+	virq = irq_reserve_ipi(ipidomain, mask);
+	BUG_ON(!virq);
+	if (!sched_virq)
+		sched_virq = virq;
+
+	if (irq_domain_is_ipi_per_cpu(ipidomain)) {
+		int cpu;
+
+		for_each_cpu(cpu, mask) {
+			smp_ipi_init_one(call_virq + cpu, "IPI call",
+					 ipi_call_interrupt);
+			smp_ipi_init_one(sched_virq + cpu, "IPI resched",
+					 ipi_resched_interrupt);
+		}
+	} else {
+		smp_ipi_init_one(call_virq, "IPI call", ipi_call_interrupt);
+		smp_ipi_init_one(sched_virq, "IPI resched",
+				 ipi_resched_interrupt);
+	}
+
+	return 0;
+}
+
+int mips_smp_ipi_free(const struct cpumask *mask)
+{
+	struct irq_domain *ipidomain;
+	struct device_node *node;
+
+	node = of_irq_find_parent(of_root);
+	ipidomain = irq_find_matching_host(node, DOMAIN_BUS_IPI);
+
+	/*
+	 * Some platforms have half DT setup. So if we found irq node but
+	 * didn't find an ipidomain, try to search for one that is not in the
+	 * DT.
+	 */
+	if (node && !ipidomain)
+		ipidomain = irq_find_matching_host(NULL, DOMAIN_BUS_IPI);
+
+	BUG_ON(!ipidomain);
+
+	if (irq_domain_is_ipi_per_cpu(ipidomain)) {
+		int cpu;
+
+		for_each_cpu(cpu, mask) {
+			free_irq(call_virq + cpu, NULL);
+			free_irq(sched_virq + cpu, NULL);
+		}
+	}
+	irq_destroy_ipi(call_virq, mask);
+	irq_destroy_ipi(sched_virq, mask);
+	return 0;
+}
+
+
+static int __init mips_smp_ipi_init(void)
+{
+	if (num_possible_cpus() == 1)
+		return 0;
+
+	mips_smp_ipi_allocate(cpu_possible_mask);
+
+	call_desc = irq_to_desc(call_virq);
+	sched_desc = irq_to_desc(sched_virq);
+
+	return 0;
+}
+early_initcall(mips_smp_ipi_init);
+#endif
+
+/*
+ * First C code run on the secondary CPUs after being started up by
+ * the master.
+ */
+asmlinkage void start_secondary(void)
+{
+	unsigned int cpu = raw_smp_processor_id();
+
+	cpu_probe();
+	per_cpu_trap_init(false);
+	rcu_cpu_starting(cpu);
+	mips_clockevent_init();
+	mp_ops->init_secondary();
+	cpu_report();
+	maar_init();
+
+	/*
+	 * XXX parity protection should be folded in here when it's converted
+	 * to an option instead of something based on .cputype
+	 */
+
+	calibrate_delay();
+	cpu_data[cpu].udelay_val = loops_per_jiffy;
+
+	set_cpu_sibling_map(cpu);
+	set_cpu_core_map(cpu);
+
+	cpumask_set_cpu(cpu, &cpu_coherent_mask);
+	notify_cpu_starting(cpu);
+
+	/* Notify boot CPU that we're starting & ready to sync counters */
+	complete(&cpu_starting);
+
+	synchronise_count_slave(cpu);
+
+	/* The CPU is running and counters synchronised, now mark it online */
+	set_cpu_online(cpu, true);
+
+	calculate_cpu_foreign_map();
+
+	/*
+	 * Notify boot CPU that we're up & online and it can safely return
+	 * from __cpu_up
+	 */
+	complete(&cpu_running);
+
+	/*
+	 * irq will be enabled in ->smp_finish(), enabling it too early
+	 * is dangerous.
+	 */
+	WARN_ON_ONCE(!irqs_disabled());
+	mp_ops->smp_finish();
+
+	cpu_startup_entry(CPUHP_AP_ONLINE_IDLE);
+}
+
+static void stop_this_cpu(void *dummy)
+{
+	/*
+	 * Remove this CPU:
+	 */
+
+	set_cpu_online(smp_processor_id(), false);
+	calculate_cpu_foreign_map();
+	local_irq_disable();
+	while (1);
+}
+
+void smp_send_stop(void)
+{
+	smp_call_function(stop_this_cpu, NULL, 0);
+}
+
+void __init smp_cpus_done(unsigned int max_cpus)
+{
+}
+
+/* called from main before smp_init() */
+void __init smp_prepare_cpus(unsigned int max_cpus)
+{
+	init_new_context(current, &init_mm);
+	current_thread_info()->cpu = 0;
+	mp_ops->prepare_cpus(max_cpus);
+	set_cpu_sibling_map(0);
+	set_cpu_core_map(0);
+	calculate_cpu_foreign_map();
+#ifndef CONFIG_HOTPLUG_CPU
+	init_cpu_present(cpu_possible_mask);
+#endif
+	cpumask_copy(&cpu_coherent_mask, cpu_possible_mask);
+}
+
+/* preload SMP state for boot cpu */
+void smp_prepare_boot_cpu(void)
+{
+	if (mp_ops->prepare_boot_cpu)
+		mp_ops->prepare_boot_cpu();
+	set_cpu_possible(0, true);
+	set_cpu_online(0, true);
+}
+
+int __cpu_up(unsigned int cpu, struct task_struct *tidle)
+{
+	int err;
+
+	err = mp_ops->boot_secondary(cpu, tidle);
+	if (err)
+		return err;
+
+	/* Wait for CPU to start and be ready to sync counters */
+	if (!wait_for_completion_timeout(&cpu_starting,
+					 msecs_to_jiffies(1000))) {
+		pr_crit("CPU%u: failed to start\n", cpu);
+		return -EIO;
+	}
+
+	synchronise_count_master(cpu);
+
+	/* Wait for CPU to finish startup & mark itself online before return */
+	wait_for_completion(&cpu_running);
+	return 0;
+}
+
+/* Not really SMP stuff ... */
+int setup_profiling_timer(unsigned int multiplier)
+{
+	return 0;
+}
+
+static void flush_tlb_all_ipi(void *info)
+{
+	local_flush_tlb_all();
+}
+
+void flush_tlb_all(void)
+{
+	if (cpu_has_mmid) {
+		htw_stop();
+		ginvt_full();
+		sync_ginv();
+		instruction_hazard();
+		htw_start();
+		return;
+	}
+
+	on_each_cpu(flush_tlb_all_ipi, NULL, 1);
+}
+
+static void flush_tlb_mm_ipi(void *mm)
+{
+	drop_mmu_context((struct mm_struct *)mm);
+}
+
+/*
+ * Special Variant of smp_call_function for use by TLB functions:
+ *
+ *  o No return value
+ *  o collapses to normal function call on UP kernels
+ *  o collapses to normal function call on systems with a single shared
+ *    primary cache.
+ */
+static inline void smp_on_other_tlbs(void (*func) (void *info), void *info)
+{
+	smp_call_function(func, info, 1);
+}
+
+static inline void smp_on_each_tlb(void (*func) (void *info), void *info)
+{
+	preempt_disable();
+
+	smp_on_other_tlbs(func, info);
+	func(info);
+
+	preempt_enable();
+}
+
+/*
+ * The following tlb flush calls are invoked when old translations are
+ * being torn down, or pte attributes are changing. For single threaded
+ * address spaces, a new context is obtained on the current cpu, and tlb
+ * context on other cpus are invalidated to force a new context allocation
+ * at switch_mm time, should the mm ever be used on other cpus. For
+ * multithreaded address spaces, inter-CPU interrupts have to be sent.
+ * Another case where inter-CPU interrupts are required is when the target
+ * mm might be active on another cpu (eg debuggers doing the flushes on
+ * behalf of debugees, kswapd stealing pages from another process etc).
+ * Kanoj 07/00.
+ */
+
+void flush_tlb_mm(struct mm_struct *mm)
+{
+	if (!mm)
+		return;
+
+	if (atomic_read(&mm->mm_users) == 0)
+		return;		/* happens as a result of exit_mmap() */
+
+	preempt_disable();
+
+	if (cpu_has_mmid) {
+		/*
+		 * No need to worry about other CPUs - the ginvt in
+		 * drop_mmu_context() will be globalized.
+		 */
+	} else if ((atomic_read(&mm->mm_users) != 1) || (current->mm != mm)) {
+		smp_on_other_tlbs(flush_tlb_mm_ipi, mm);
+	} else {
+		unsigned int cpu;
+
+		for_each_online_cpu(cpu) {
+			if (cpu != smp_processor_id() && cpu_context(cpu, mm))
+				set_cpu_context(cpu, mm, 0);
+		}
+	}
+	drop_mmu_context(mm);
+
+	preempt_enable();
+}
+
+struct flush_tlb_data {
+	struct vm_area_struct *vma;
+	unsigned long addr1;
+	unsigned long addr2;
+};
+
+static void flush_tlb_range_ipi(void *info)
+{
+	struct flush_tlb_data *fd = info;
+
+	local_flush_tlb_range(fd->vma, fd->addr1, fd->addr2);
+}
+
+void flush_tlb_range(struct vm_area_struct *vma, unsigned long start, unsigned long end)
+{
+	struct mm_struct *mm = vma->vm_mm;
+	unsigned long addr;
+	u32 old_mmid;
+
+	preempt_disable();
+	if (cpu_has_mmid) {
+		htw_stop();
+		old_mmid = read_c0_memorymapid();
+		write_c0_memorymapid(cpu_asid(0, mm));
+		mtc0_tlbw_hazard();
+		addr = round_down(start, PAGE_SIZE * 2);
+		end = round_up(end, PAGE_SIZE * 2);
+		do {
+			ginvt_va_mmid(addr);
+			sync_ginv();
+			addr += PAGE_SIZE * 2;
+		} while (addr < end);
+		write_c0_memorymapid(old_mmid);
+		instruction_hazard();
+		htw_start();
+	} else if ((atomic_read(&mm->mm_users) != 1) || (current->mm != mm)) {
+		struct flush_tlb_data fd = {
+			.vma = vma,
+			.addr1 = start,
+			.addr2 = end,
+		};
+
+		smp_on_other_tlbs(flush_tlb_range_ipi, &fd);
+		local_flush_tlb_range(vma, start, end);
+	} else {
+		unsigned int cpu;
+		int exec = vma->vm_flags & VM_EXEC;
+
+		for_each_online_cpu(cpu) {
+			/*
+			 * flush_cache_range() will only fully flush icache if
+			 * the VMA is executable, otherwise we must invalidate
+			 * ASID without it appearing to has_valid_asid() as if
+			 * mm has been completely unused by that CPU.
+			 */
+			if (cpu != smp_processor_id() && cpu_context(cpu, mm))
+				set_cpu_context(cpu, mm, !exec);
+		}
+		local_flush_tlb_range(vma, start, end);
+	}
+	preempt_enable();
+}
+
+static void flush_tlb_kernel_range_ipi(void *info)
+{
+	struct flush_tlb_data *fd = info;
+
+	local_flush_tlb_kernel_range(fd->addr1, fd->addr2);
+}
+
+void flush_tlb_kernel_range(unsigned long start, unsigned long end)
+{
+	struct flush_tlb_data fd = {
+		.addr1 = start,
+		.addr2 = end,
+	};
+
+	on_each_cpu(flush_tlb_kernel_range_ipi, &fd, 1);
+}
+
+static void flush_tlb_page_ipi(void *info)
+{
+	struct flush_tlb_data *fd = info;
+
+	local_flush_tlb_page(fd->vma, fd->addr1);
+}
+
+void flush_tlb_page(struct vm_area_struct *vma, unsigned long page)
+{
+	u32 old_mmid;
+
+	preempt_disable();
+	if (cpu_has_mmid) {
+		htw_stop();
+		old_mmid = read_c0_memorymapid();
+		write_c0_memorymapid(cpu_asid(0, vma->vm_mm));
+		mtc0_tlbw_hazard();
+		ginvt_va_mmid(page);
+		sync_ginv();
+		write_c0_memorymapid(old_mmid);
+		instruction_hazard();
+		htw_start();
+	} else if ((atomic_read(&vma->vm_mm->mm_users) != 1) ||
+		   (current->mm != vma->vm_mm)) {
+		struct flush_tlb_data fd = {
+			.vma = vma,
+			.addr1 = page,
+		};
+
+		smp_on_other_tlbs(flush_tlb_page_ipi, &fd);
+		local_flush_tlb_page(vma, page);
+	} else {
+		unsigned int cpu;
+
+		for_each_online_cpu(cpu) {
+			/*
+			 * flush_cache_page() only does partial flushes, so
+			 * invalidate ASID without it appearing to
+			 * has_valid_asid() as if mm has been completely unused
+			 * by that CPU.
+			 */
+			if (cpu != smp_processor_id() && cpu_context(cpu, vma->vm_mm))
+				set_cpu_context(cpu, vma->vm_mm, 1);
+		}
+		local_flush_tlb_page(vma, page);
+	}
+	preempt_enable();
+}
+
+static void flush_tlb_one_ipi(void *info)
+{
+	unsigned long vaddr = (unsigned long) info;
+
+	local_flush_tlb_one(vaddr);
+}
+
+void flush_tlb_one(unsigned long vaddr)
+{
+	smp_on_each_tlb(flush_tlb_one_ipi, (void *) vaddr);
+}
+
+EXPORT_SYMBOL(flush_tlb_page);
+EXPORT_SYMBOL(flush_tlb_one);
+
+#ifdef CONFIG_GENERIC_CLOCKEVENTS_BROADCAST
+
+static void tick_broadcast_callee(void *info)
+{
+	tick_receive_broadcast();
+}
+
+static DEFINE_PER_CPU(call_single_data_t, tick_broadcast_csd) =
+	CSD_INIT(tick_broadcast_callee, NULL);
+
+void tick_broadcast(const struct cpumask *mask)
+{
+	call_single_data_t *csd;
+	int cpu;
+
+	for_each_cpu(cpu, mask) {
+		csd = &per_cpu(tick_broadcast_csd, cpu);
+		smp_call_function_single_async(cpu, csd);
+	}
+}
+
+#endif /* CONFIG_GENERIC_CLOCKEVENTS_BROADCAST */
diff --git a/arch/mips/kernel/spinlock_test.c b/arch/mips/kernel/spinlock_test.c
new file mode 100644
index 000000000..90f53e041
--- /dev/null
+++ b/arch/mips/kernel/spinlock_test.c
@@ -0,0 +1,127 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/init.h>
+#include <linux/kthread.h>
+#include <linux/hrtimer.h>
+#include <linux/fs.h>
+#include <linux/debugfs.h>
+#include <linux/export.h>
+#include <linux/spinlock.h>
+#include <asm/debug.h>
+
+static int ss_get(void *data, u64 *val)
+{
+	ktime_t start, finish;
+	int loops;
+	int cont;
+	DEFINE_RAW_SPINLOCK(ss_spin);
+
+	loops = 1000000;
+	cont = 1;
+
+	start = ktime_get();
+
+	while (cont) {
+		raw_spin_lock(&ss_spin);
+		loops--;
+		if (loops == 0)
+			cont = 0;
+		raw_spin_unlock(&ss_spin);
+	}
+
+	finish = ktime_get();
+
+	*val = ktime_us_delta(finish, start);
+
+	return 0;
+}
+
+DEFINE_DEBUGFS_ATTRIBUTE(fops_ss, ss_get, NULL, "%llu\n");
+
+
+
+struct spin_multi_state {
+	raw_spinlock_t lock;
+	atomic_t start_wait;
+	atomic_t enter_wait;
+	atomic_t exit_wait;
+	int loops;
+};
+
+struct spin_multi_per_thread {
+	struct spin_multi_state *state;
+	ktime_t start;
+};
+
+static int multi_other(void *data)
+{
+	int loops;
+	int cont;
+	struct spin_multi_per_thread *pt = data;
+	struct spin_multi_state *s = pt->state;
+
+	loops = s->loops;
+	cont = 1;
+
+	atomic_dec(&s->enter_wait);
+
+	while (atomic_read(&s->enter_wait))
+		; /* spin */
+
+	pt->start = ktime_get();
+
+	atomic_dec(&s->start_wait);
+
+	while (atomic_read(&s->start_wait))
+		; /* spin */
+
+	while (cont) {
+		raw_spin_lock(&s->lock);
+		loops--;
+		if (loops == 0)
+			cont = 0;
+		raw_spin_unlock(&s->lock);
+	}
+
+	atomic_dec(&s->exit_wait);
+	while (atomic_read(&s->exit_wait))
+		; /* spin */
+	return 0;
+}
+
+static int multi_get(void *data, u64 *val)
+{
+	ktime_t finish;
+	struct spin_multi_state ms;
+	struct spin_multi_per_thread t1, t2;
+
+	ms.lock = __RAW_SPIN_LOCK_UNLOCKED("multi_get");
+	ms.loops = 1000000;
+
+	atomic_set(&ms.start_wait, 2);
+	atomic_set(&ms.enter_wait, 2);
+	atomic_set(&ms.exit_wait, 2);
+	t1.state = &ms;
+	t2.state = &ms;
+
+	kthread_run(multi_other, &t2, "multi_get");
+
+	multi_other(&t1);
+
+	finish = ktime_get();
+
+	*val = ktime_us_delta(finish, t1.start);
+
+	return 0;
+}
+
+DEFINE_DEBUGFS_ATTRIBUTE(fops_multi, multi_get, NULL, "%llu\n");
+
+static int __init spinlock_test(void)
+{
+	debugfs_create_file_unsafe("spin_single", S_IRUGO, mips_debugfs_dir, NULL,
+			    &fops_ss);
+	debugfs_create_file_unsafe("spin_multi", S_IRUGO, mips_debugfs_dir, NULL,
+			    &fops_multi);
+	return 0;
+}
+device_initcall(spinlock_test);
diff --git a/arch/mips/kernel/spram.c b/arch/mips/kernel/spram.c
new file mode 100644
index 000000000..d5d96214c
--- /dev/null
+++ b/arch/mips/kernel/spram.c
@@ -0,0 +1,220 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * MIPS SPRAM support
+ *
+ * Copyright (C) 2007, 2008 MIPS Technologies, Inc.
+ */
+#include <linux/kernel.h>
+#include <linux/ptrace.h>
+#include <linux/stddef.h>
+
+#include <asm/fpu.h>
+#include <asm/mipsregs.h>
+#include <asm/r4kcache.h>
+#include <asm/hazards.h>
+
+/*
+ * These definitions are correct for the 24K/34K/74K SPRAM sample
+ * implementation. The 4KS interpreted the tags differently...
+ */
+#define SPRAM_TAG0_ENABLE	0x00000080
+#define SPRAM_TAG0_PA_MASK	0xfffff000
+#define SPRAM_TAG1_SIZE_MASK	0xfffff000
+
+#define SPRAM_TAG_STRIDE	8
+
+#define ERRCTL_SPRAM		(1 << 28)
+
+/* errctl access */
+#define read_c0_errctl(x) read_c0_ecc(x)
+#define write_c0_errctl(x) write_c0_ecc(x)
+
+/*
+ * Different semantics to the set_c0_* function built by __BUILD_SET_C0
+ */
+static unsigned int bis_c0_errctl(unsigned int set)
+{
+	unsigned int res;
+	res = read_c0_errctl();
+	write_c0_errctl(res | set);
+	return res;
+}
+
+static void ispram_store_tag(unsigned int offset, unsigned int data)
+{
+	unsigned int errctl;
+
+	/* enable SPRAM tag access */
+	errctl = bis_c0_errctl(ERRCTL_SPRAM);
+	ehb();
+
+	write_c0_taglo(data);
+	ehb();
+
+	cache_op(Index_Store_Tag_I, CKSEG0|offset);
+	ehb();
+
+	write_c0_errctl(errctl);
+	ehb();
+}
+
+
+static unsigned int ispram_load_tag(unsigned int offset)
+{
+	unsigned int data;
+	unsigned int errctl;
+
+	/* enable SPRAM tag access */
+	errctl = bis_c0_errctl(ERRCTL_SPRAM);
+	ehb();
+	cache_op(Index_Load_Tag_I, CKSEG0 | offset);
+	ehb();
+	data = read_c0_taglo();
+	ehb();
+	write_c0_errctl(errctl);
+	ehb();
+
+	return data;
+}
+
+static void dspram_store_tag(unsigned int offset, unsigned int data)
+{
+	unsigned int errctl;
+
+	/* enable SPRAM tag access */
+	errctl = bis_c0_errctl(ERRCTL_SPRAM);
+	ehb();
+	write_c0_dtaglo(data);
+	ehb();
+	cache_op(Index_Store_Tag_D, CKSEG0 | offset);
+	ehb();
+	write_c0_errctl(errctl);
+	ehb();
+}
+
+
+static unsigned int dspram_load_tag(unsigned int offset)
+{
+	unsigned int data;
+	unsigned int errctl;
+
+	errctl = bis_c0_errctl(ERRCTL_SPRAM);
+	ehb();
+	cache_op(Index_Load_Tag_D, CKSEG0 | offset);
+	ehb();
+	data = read_c0_dtaglo();
+	ehb();
+	write_c0_errctl(errctl);
+	ehb();
+
+	return data;
+}
+
+static void probe_spram(char *type,
+	    unsigned int base,
+	    unsigned int (*read)(unsigned int),
+	    void (*write)(unsigned int, unsigned int))
+{
+	unsigned int firstsize = 0, lastsize = 0;
+	unsigned int firstpa = 0, lastpa = 0, pa = 0;
+	unsigned int offset = 0;
+	unsigned int size, tag0, tag1;
+	unsigned int enabled;
+	int i;
+
+	/*
+	 * The limit is arbitrary but avoids the loop running away if
+	 * the SPRAM tags are implemented differently
+	 */
+
+	for (i = 0; i < 8; i++) {
+		tag0 = read(offset);
+		tag1 = read(offset+SPRAM_TAG_STRIDE);
+		pr_debug("DBG %s%d: tag0=%08x tag1=%08x\n",
+			 type, i, tag0, tag1);
+
+		size = tag1 & SPRAM_TAG1_SIZE_MASK;
+
+		if (size == 0)
+			break;
+
+		if (i != 0) {
+			/* tags may repeat... */
+			if ((pa == firstpa && size == firstsize) ||
+			    (pa == lastpa && size == lastsize))
+				break;
+		}
+
+		/* Align base with size */
+		base = (base + size - 1) & ~(size-1);
+
+		/* reprogram the base address base address and enable */
+		tag0 = (base & SPRAM_TAG0_PA_MASK) | SPRAM_TAG0_ENABLE;
+		write(offset, tag0);
+
+		base += size;
+
+		/* reread the tag */
+		tag0 = read(offset);
+		pa = tag0 & SPRAM_TAG0_PA_MASK;
+		enabled = tag0 & SPRAM_TAG0_ENABLE;
+
+		if (i == 0) {
+			firstpa = pa;
+			firstsize = size;
+		}
+
+		lastpa = pa;
+		lastsize = size;
+
+		if (strcmp(type, "DSPRAM") == 0) {
+			unsigned int *vp = (unsigned int *)(CKSEG1 | pa);
+			unsigned int v;
+#define TDAT	0x5a5aa5a5
+			vp[0] = TDAT;
+			vp[1] = ~TDAT;
+
+			mb();
+
+			v = vp[0];
+			if (v != TDAT)
+				printk(KERN_ERR "vp=%p wrote=%08x got=%08x\n",
+				       vp, TDAT, v);
+			v = vp[1];
+			if (v != ~TDAT)
+				printk(KERN_ERR "vp=%p wrote=%08x got=%08x\n",
+				       vp+1, ~TDAT, v);
+		}
+
+		pr_info("%s%d: PA=%08x,Size=%08x%s\n",
+			type, i, pa, size, enabled ? ",enabled" : "");
+		offset += 2 * SPRAM_TAG_STRIDE;
+	}
+}
+void spram_config(void)
+{
+	unsigned int config0;
+
+	switch (current_cpu_type()) {
+	case CPU_24K:
+	case CPU_34K:
+	case CPU_74K:
+	case CPU_1004K:
+	case CPU_1074K:
+	case CPU_INTERAPTIV:
+	case CPU_PROAPTIV:
+	case CPU_P5600:
+	case CPU_QEMU_GENERIC:
+	case CPU_I6400:
+	case CPU_P6600:
+		config0 = read_c0_config();
+		/* FIXME: addresses are Malta specific */
+		if (config0 & MIPS_CONF_ISP) {
+			probe_spram("ISPRAM", 0x1c000000,
+				    &ispram_load_tag, &ispram_store_tag);
+		}
+		if (config0 & MIPS_CONF_DSP)
+			probe_spram("DSPRAM", 0x1c100000,
+				    &dspram_load_tag, &dspram_store_tag);
+	}
+}
diff --git a/arch/mips/kernel/stacktrace.c b/arch/mips/kernel/stacktrace.c
new file mode 100644
index 000000000..f2e720940
--- /dev/null
+++ b/arch/mips/kernel/stacktrace.c
@@ -0,0 +1,93 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Stack trace management functions
+ *
+ *  Copyright (C) 2006 Atsushi Nemoto <anemo@mba.ocn.ne.jp>
+ */
+#include <linux/sched.h>
+#include <linux/sched/debug.h>
+#include <linux/sched/task_stack.h>
+#include <linux/stacktrace.h>
+#include <linux/export.h>
+#include <asm/stacktrace.h>
+
+/*
+ * Save stack-backtrace addresses into a stack_trace buffer:
+ */
+static void save_raw_context_stack(struct stack_trace *trace,
+	unsigned long reg29, int savesched)
+{
+	unsigned long *sp = (unsigned long *)reg29;
+	unsigned long addr;
+
+	while (!kstack_end(sp)) {
+		addr = *sp++;
+		if (__kernel_text_address(addr) &&
+		    (savesched || !in_sched_functions(addr))) {
+			if (trace->skip > 0)
+				trace->skip--;
+			else
+				trace->entries[trace->nr_entries++] = addr;
+			if (trace->nr_entries >= trace->max_entries)
+				break;
+		}
+	}
+}
+
+static void save_context_stack(struct stack_trace *trace,
+	struct task_struct *tsk, struct pt_regs *regs, int savesched)
+{
+	unsigned long sp = regs->regs[29];
+#ifdef CONFIG_KALLSYMS
+	unsigned long ra = regs->regs[31];
+	unsigned long pc = regs->cp0_epc;
+
+	if (raw_show_trace || !__kernel_text_address(pc)) {
+		unsigned long stack_page =
+			(unsigned long)task_stack_page(tsk);
+		if (stack_page && sp >= stack_page &&
+		    sp <= stack_page + THREAD_SIZE - 32)
+			save_raw_context_stack(trace, sp, savesched);
+		return;
+	}
+	do {
+		if (savesched || !in_sched_functions(pc)) {
+			if (trace->skip > 0)
+				trace->skip--;
+			else
+				trace->entries[trace->nr_entries++] = pc;
+			if (trace->nr_entries >= trace->max_entries)
+				break;
+		}
+		pc = unwind_stack(tsk, &sp, pc, &ra);
+	} while (pc);
+#else
+	save_raw_context_stack(trace, sp, savesched);
+#endif
+}
+
+/*
+ * Save stack-backtrace addresses into a stack_trace buffer.
+ */
+void save_stack_trace(struct stack_trace *trace)
+{
+	save_stack_trace_tsk(current, trace);
+}
+EXPORT_SYMBOL_GPL(save_stack_trace);
+
+void save_stack_trace_tsk(struct task_struct *tsk, struct stack_trace *trace)
+{
+	struct pt_regs dummyregs;
+	struct pt_regs *regs = &dummyregs;
+
+	WARN_ON(trace->nr_entries || !trace->max_entries);
+
+	if (tsk != current) {
+		regs->regs[29] = tsk->thread.reg29;
+		regs->regs[31] = 0;
+		regs->cp0_epc = tsk->thread.reg31;
+	} else
+		prepare_frametrace(regs);
+	save_context_stack(trace, tsk, regs, tsk == current);
+}
+EXPORT_SYMBOL_GPL(save_stack_trace_tsk);
diff --git a/arch/mips/kernel/sync-r4k.c b/arch/mips/kernel/sync-r4k.c
new file mode 100644
index 000000000..abdd7aaa3
--- /dev/null
+++ b/arch/mips/kernel/sync-r4k.c
@@ -0,0 +1,122 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Count register synchronisation.
+ *
+ * All CPUs will have their count registers synchronised to the CPU0 next time
+ * value. This can cause a small timewarp for CPU0. All other CPU's should
+ * not have done anything significant (but they may have had interrupts
+ * enabled briefly - prom_smp_finish() should not be responsible for enabling
+ * interrupts...)
+ */
+
+#include <linux/kernel.h>
+#include <linux/irqflags.h>
+#include <linux/cpumask.h>
+
+#include <asm/r4k-timer.h>
+#include <linux/atomic.h>
+#include <asm/barrier.h>
+#include <asm/mipsregs.h>
+
+static unsigned int initcount = 0;
+static atomic_t count_count_start = ATOMIC_INIT(0);
+static atomic_t count_count_stop = ATOMIC_INIT(0);
+
+#define COUNTON 100
+#define NR_LOOPS 3
+
+void synchronise_count_master(int cpu)
+{
+	int i;
+	unsigned long flags;
+
+	pr_info("Synchronize counters for CPU %u: ", cpu);
+
+	local_irq_save(flags);
+
+	/*
+	 * We loop a few times to get a primed instruction cache,
+	 * then the last pass is more or less synchronised and
+	 * the master and slaves each set their cycle counters to a known
+	 * value all at once. This reduces the chance of having random offsets
+	 * between the processors, and guarantees that the maximum
+	 * delay between the cycle counters is never bigger than
+	 * the latency of information-passing (cachelines) between
+	 * two CPUs.
+	 */
+
+	for (i = 0; i < NR_LOOPS; i++) {
+		/* slaves loop on '!= 2' */
+		while (atomic_read(&count_count_start) != 1)
+			mb();
+		atomic_set(&count_count_stop, 0);
+		smp_wmb();
+
+		/* Let the slave writes its count register */
+		atomic_inc(&count_count_start);
+
+		/* Count will be initialised to current timer */
+		if (i == 1)
+			initcount = read_c0_count();
+
+		/*
+		 * Everyone initialises count in the last loop:
+		 */
+		if (i == NR_LOOPS-1)
+			write_c0_count(initcount);
+
+		/*
+		 * Wait for slave to leave the synchronization point:
+		 */
+		while (atomic_read(&count_count_stop) != 1)
+			mb();
+		atomic_set(&count_count_start, 0);
+		smp_wmb();
+		atomic_inc(&count_count_stop);
+	}
+	/* Arrange for an interrupt in a short while */
+	write_c0_compare(read_c0_count() + COUNTON);
+
+	local_irq_restore(flags);
+
+	/*
+	 * i386 code reported the skew here, but the
+	 * count registers were almost certainly out of sync
+	 * so no point in alarming people
+	 */
+	pr_cont("done.\n");
+}
+
+void synchronise_count_slave(int cpu)
+{
+	int i;
+	unsigned long flags;
+
+	local_irq_save(flags);
+
+	/*
+	 * Not every cpu is online at the time this gets called,
+	 * so we first wait for the master to say everyone is ready
+	 */
+
+	for (i = 0; i < NR_LOOPS; i++) {
+		atomic_inc(&count_count_start);
+		while (atomic_read(&count_count_start) != 2)
+			mb();
+
+		/*
+		 * Everyone initialises count in the last loop:
+		 */
+		if (i == NR_LOOPS-1)
+			write_c0_count(initcount);
+
+		atomic_inc(&count_count_stop);
+		while (atomic_read(&count_count_stop) != 2)
+			mb();
+	}
+	/* Arrange for an interrupt in a short while */
+	write_c0_compare(read_c0_count() + COUNTON);
+
+	local_irq_restore(flags);
+}
+#undef NR_LOOPS
diff --git a/arch/mips/kernel/syscall.c b/arch/mips/kernel/syscall.c
new file mode 100644
index 000000000..ae93a607d
--- /dev/null
+++ b/arch/mips/kernel/syscall.c
@@ -0,0 +1,242 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995, 1996, 1997, 2000, 2001, 05 by Ralf Baechle
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ * Copyright (C) 2001 MIPS Technologies, Inc.
+ */
+#include <linux/capability.h>
+#include <linux/errno.h>
+#include <linux/linkage.h>
+#include <linux/fs.h>
+#include <linux/smp.h>
+#include <linux/ptrace.h>
+#include <linux/string.h>
+#include <linux/syscalls.h>
+#include <linux/file.h>
+#include <linux/utsname.h>
+#include <linux/unistd.h>
+#include <linux/sem.h>
+#include <linux/msg.h>
+#include <linux/shm.h>
+#include <linux/compiler.h>
+#include <linux/ipc.h>
+#include <linux/uaccess.h>
+#include <linux/slab.h>
+#include <linux/elf.h>
+#include <linux/sched/task_stack.h>
+
+#include <asm/asm.h>
+#include <asm/asm-eva.h>
+#include <asm/branch.h>
+#include <asm/cachectl.h>
+#include <asm/cacheflush.h>
+#include <asm/asm-offsets.h>
+#include <asm/signal.h>
+#include <asm/sim.h>
+#include <asm/shmparam.h>
+#include <asm/sync.h>
+#include <asm/sysmips.h>
+#include <asm/switch_to.h>
+
+/*
+ * For historic reasons the pipe(2) syscall on MIPS has an unusual calling
+ * convention.	It returns results in registers $v0 / $v1 which means there
+ * is no need for it to do verify the validity of a userspace pointer
+ * argument.  Historically that used to be expensive in Linux.	These days
+ * the performance advantage is negligible.
+ */
+asmlinkage int sysm_pipe(void)
+{
+	int fd[2];
+	int error = do_pipe_flags(fd, 0);
+	if (error)
+		return error;
+	current_pt_regs()->regs[3] = fd[1];
+	return fd[0];
+}
+
+SYSCALL_DEFINE6(mips_mmap, unsigned long, addr, unsigned long, len,
+	unsigned long, prot, unsigned long, flags, unsigned long,
+	fd, off_t, offset)
+{
+	if (offset & ~PAGE_MASK)
+		return -EINVAL;
+	return ksys_mmap_pgoff(addr, len, prot, flags, fd,
+			       offset >> PAGE_SHIFT);
+}
+
+SYSCALL_DEFINE6(mips_mmap2, unsigned long, addr, unsigned long, len,
+	unsigned long, prot, unsigned long, flags, unsigned long, fd,
+	unsigned long, pgoff)
+{
+	if (pgoff & (~PAGE_MASK >> 12))
+		return -EINVAL;
+
+	return ksys_mmap_pgoff(addr, len, prot, flags, fd,
+			       pgoff >> (PAGE_SHIFT - 12));
+}
+
+save_static_function(sys_fork);
+save_static_function(sys_clone);
+save_static_function(sys_clone3);
+
+SYSCALL_DEFINE1(set_thread_area, unsigned long, addr)
+{
+	struct thread_info *ti = task_thread_info(current);
+
+	ti->tp_value = addr;
+	if (cpu_has_userlocal)
+		write_c0_userlocal(addr);
+
+	return 0;
+}
+
+static inline int mips_atomic_set(unsigned long addr, unsigned long new)
+{
+	unsigned long old, tmp;
+	struct pt_regs *regs;
+	unsigned int err;
+
+	if (unlikely(addr & 3))
+		return -EINVAL;
+
+	if (unlikely(!access_ok((const void __user *)addr, 4)))
+		return -EINVAL;
+
+	if (cpu_has_llsc && IS_ENABLED(CONFIG_WAR_R10000_LLSC)) {
+		__asm__ __volatile__ (
+		"	.set	push					\n"
+		"	.set	arch=r4000				\n"
+		"	li	%[err], 0				\n"
+		"1:	ll	%[old], (%[addr])			\n"
+		"	move	%[tmp], %[new]				\n"
+		"2:	sc	%[tmp], (%[addr])			\n"
+		"	beqzl	%[tmp], 1b				\n"
+		"3:							\n"
+		"	.insn						\n"
+		"	.section .fixup,\"ax\"				\n"
+		"4:	li	%[err], %[efault]			\n"
+		"	j	3b					\n"
+		"	.previous					\n"
+		"	.section __ex_table,\"a\"			\n"
+		"	"STR(PTR_WD)"	1b, 4b				\n"
+		"	"STR(PTR_WD)"	2b, 4b				\n"
+		"	.previous					\n"
+		"	.set	pop					\n"
+		: [old] "=&r" (old),
+		  [err] "=&r" (err),
+		  [tmp] "=&r" (tmp)
+		: [addr] "r" (addr),
+		  [new] "r" (new),
+		  [efault] "i" (-EFAULT)
+		: "memory");
+	} else if (cpu_has_llsc) {
+		__asm__ __volatile__ (
+		"	.set	push					\n"
+		"	.set	"MIPS_ISA_ARCH_LEVEL"			\n"
+		"	li	%[err], 0				\n"
+		"1:							\n"
+		"	" __SYNC(full, loongson3_war) "			\n"
+		user_ll("%[old]", "(%[addr])")
+		"	move	%[tmp], %[new]				\n"
+		"2:							\n"
+		user_sc("%[tmp]", "(%[addr])")
+		"	beqz	%[tmp], 1b				\n"
+		"3:							\n"
+		"	.insn						\n"
+		"	.section .fixup,\"ax\"				\n"
+		"5:	li	%[err], %[efault]			\n"
+		"	j	3b					\n"
+		"	.previous					\n"
+		"	.section __ex_table,\"a\"			\n"
+		"	"STR(PTR_WD)"	1b, 5b				\n"
+		"	"STR(PTR_WD)"	2b, 5b				\n"
+		"	.previous					\n"
+		"	.set	pop					\n"
+		: [old] "=&r" (old),
+		  [err] "=&r" (err),
+		  [tmp] "=&r" (tmp)
+		: [addr] "r" (addr),
+		  [new] "r" (new),
+		  [efault] "i" (-EFAULT)
+		: "memory");
+	} else {
+		do {
+			preempt_disable();
+			ll_bit = 1;
+			ll_task = current;
+			preempt_enable();
+
+			err = __get_user(old, (unsigned int *) addr);
+			err |= __put_user(new, (unsigned int *) addr);
+			if (err)
+				break;
+			rmb();
+		} while (!ll_bit);
+	}
+
+	if (unlikely(err))
+		return err;
+
+	regs = current_pt_regs();
+	regs->regs[2] = old;
+	regs->regs[7] = 0;	/* No error */
+
+	/*
+	 * Don't let your children do this ...
+	 */
+	__asm__ __volatile__(
+	"	move	$29, %0						\n"
+	"	j	syscall_exit					\n"
+	: /* no outputs */
+	: "r" (regs));
+
+	/* unreached.  Honestly.  */
+	unreachable();
+}
+
+/*
+ * mips_atomic_set() normally returns directly via syscall_exit potentially
+ * clobbering static registers, so be sure to preserve them.
+ */
+save_static_function(sys_sysmips);
+
+SYSCALL_DEFINE3(sysmips, long, cmd, long, arg1, long, arg2)
+{
+	switch (cmd) {
+	case MIPS_ATOMIC_SET:
+		return mips_atomic_set(arg1, arg2);
+
+	case MIPS_FIXADE:
+		if (arg1 & ~3)
+			return -EINVAL;
+
+		if (arg1 & 1)
+			set_thread_flag(TIF_FIXADE);
+		else
+			clear_thread_flag(TIF_FIXADE);
+		if (arg1 & 2)
+			set_thread_flag(TIF_LOGADE);
+		else
+			clear_thread_flag(TIF_LOGADE);
+
+		return 0;
+
+	case FLUSH_CACHE:
+		__flush_cache_all();
+		return 0;
+	}
+
+	return -EINVAL;
+}
+
+/*
+ * No implemented yet ...
+ */
+SYSCALL_DEFINE3(cachectl, char *, addr, int, nbytes, int, op)
+{
+	return -ENOSYS;
+}
diff --git a/arch/mips/kernel/syscalls/Makefile b/arch/mips/kernel/syscalls/Makefile
new file mode 100644
index 000000000..e6b21de65
--- /dev/null
+++ b/arch/mips/kernel/syscalls/Makefile
@@ -0,0 +1,51 @@
+# SPDX-License-Identifier: GPL-2.0
+kapi := arch/$(SRCARCH)/include/generated/asm
+uapi := arch/$(SRCARCH)/include/generated/uapi/asm
+
+$(shell mkdir -p $(uapi) $(kapi))
+
+syshdr := $(srctree)/scripts/syscallhdr.sh
+sysnr := $(srctree)/$(src)/syscallnr.sh
+systbl := $(srctree)/scripts/syscalltbl.sh
+
+quiet_cmd_syshdr = SYSHDR  $@
+      cmd_syshdr = $(CONFIG_SHELL) $(syshdr) --offset __NR_Linux $< $@
+
+quiet_cmd_sysnr = SYSNR   $@
+      cmd_sysnr = $(CONFIG_SHELL) '$(sysnr)' '$<' '$@'		\
+		  '$(sysnr_abis_$(basetarget))'			\
+		  '$(sysnr_pfx_$(basetarget))'
+
+quiet_cmd_systbl = SYSTBL  $@
+      cmd_systbl = $(CONFIG_SHELL) $(systbl) $< $@
+
+$(uapi)/unistd_%.h: $(src)/syscall_%.tbl $(syshdr) FORCE
+	$(call if_changed,syshdr)
+
+sysnr_pfx_unistd_nr_n32 := N32
+sysnr_pfx_unistd_nr_n64 := 64
+sysnr_pfx_unistd_nr_o32 := O32
+
+$(kapi)/unistd_nr_%.h: $(src)/syscall_%.tbl $(sysnr) FORCE
+	$(call if_changed,sysnr)
+
+$(kapi)/syscall_table_%.h: $(src)/syscall_%.tbl $(systbl) FORCE
+	$(call if_changed,systbl)
+
+uapisyshdr-y		+= unistd_n32.h			\
+			   unistd_n64.h			\
+			   unistd_o32.h
+kapisyshdr-y		+= syscall_table_n32.h		\
+			   syscall_table_n64.h		\
+			   syscall_table_o32.h		\
+			   unistd_nr_n32.h		\
+			   unistd_nr_n64.h		\
+			   unistd_nr_o32.h
+
+uapisyshdr-y	:= $(addprefix $(uapi)/, $(uapisyshdr-y))
+kapisyshdr-y	:= $(addprefix $(kapi)/, $(kapisyshdr-y))
+targets		+= $(addprefix ../../../../, $(uapisyshdr-y) $(kapisyshdr-y))
+
+PHONY += all
+all: $(uapisyshdr-y) $(kapisyshdr-y)
+	@:
diff --git a/arch/mips/kernel/syscalls/syscall_n32.tbl b/arch/mips/kernel/syscalls/syscall_n32.tbl
new file mode 100644
index 000000000..253ff994e
--- /dev/null
+++ b/arch/mips/kernel/syscalls/syscall_n32.tbl
@@ -0,0 +1,391 @@
+# SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note
+#
+# system call numbers and entry vectors for mips
+#
+# The format is:
+# <number> <abi> <name> <entry point> <compat entry point>
+#
+# The <abi> is always "n32" for this file.
+#
+0	n32	read				sys_read
+1	n32	write				sys_write
+2	n32	open				sys_open
+3	n32	close				sys_close
+4	n32	stat				sys_newstat
+5	n32	fstat				sys_newfstat
+6	n32	lstat				sys_newlstat
+7	n32	poll				sys_poll
+8	n32	lseek				sys_lseek
+9	n32	mmap				sys_mips_mmap
+10	n32	mprotect			sys_mprotect
+11	n32	munmap				sys_munmap
+12	n32	brk				sys_brk
+13	n32	rt_sigaction			compat_sys_rt_sigaction
+14	n32	rt_sigprocmask			compat_sys_rt_sigprocmask
+15	n32	ioctl				compat_sys_ioctl
+16	n32	pread64				sys_pread64
+17	n32	pwrite64			sys_pwrite64
+18	n32	readv				sys_readv
+19	n32	writev				sys_writev
+20	n32	access				sys_access
+21	n32	pipe				sysm_pipe
+22	n32	_newselect			compat_sys_select
+23	n32	sched_yield			sys_sched_yield
+24	n32	mremap				sys_mremap
+25	n32	msync				sys_msync
+26	n32	mincore				sys_mincore
+27	n32	madvise				sys_madvise
+28	n32	shmget				sys_shmget
+29	n32	shmat				sys_shmat
+30	n32	shmctl				compat_sys_old_shmctl
+31	n32	dup				sys_dup
+32	n32	dup2				sys_dup2
+33	n32	pause				sys_pause
+34	n32	nanosleep			sys_nanosleep_time32
+35	n32	getitimer			compat_sys_getitimer
+36	n32	setitimer			compat_sys_setitimer
+37	n32	alarm				sys_alarm
+38	n32	getpid				sys_getpid
+39	n32	sendfile			compat_sys_sendfile
+40	n32	socket				sys_socket
+41	n32	connect				sys_connect
+42	n32	accept				sys_accept
+43	n32	sendto				sys_sendto
+44	n32	recvfrom			compat_sys_recvfrom
+45	n32	sendmsg				compat_sys_sendmsg
+46	n32	recvmsg				compat_sys_recvmsg
+47	n32	shutdown			sys_shutdown
+48	n32	bind				sys_bind
+49	n32	listen				sys_listen
+50	n32	getsockname			sys_getsockname
+51	n32	getpeername			sys_getpeername
+52	n32	socketpair			sys_socketpair
+53	n32	setsockopt			sys_setsockopt
+54	n32	getsockopt			sys_getsockopt
+55	n32	clone				__sys_clone
+56	n32	fork				__sys_fork
+57	n32	execve				compat_sys_execve
+58	n32	exit				sys_exit
+59	n32	wait4				compat_sys_wait4
+60	n32	kill				sys_kill
+61	n32	uname				sys_newuname
+62	n32	semget				sys_semget
+63	n32	semop				sys_semop
+64	n32	semctl				compat_sys_old_semctl
+65	n32	shmdt				sys_shmdt
+66	n32	msgget				sys_msgget
+67	n32	msgsnd				compat_sys_msgsnd
+68	n32	msgrcv				compat_sys_msgrcv
+69	n32	msgctl				compat_sys_old_msgctl
+70	n32	fcntl				compat_sys_fcntl
+71	n32	flock				sys_flock
+72	n32	fsync				sys_fsync
+73	n32	fdatasync			sys_fdatasync
+74	n32	truncate			sys_truncate
+75	n32	ftruncate			sys_ftruncate
+76	n32	getdents			compat_sys_getdents
+77	n32	getcwd				sys_getcwd
+78	n32	chdir				sys_chdir
+79	n32	fchdir				sys_fchdir
+80	n32	rename				sys_rename
+81	n32	mkdir				sys_mkdir
+82	n32	rmdir				sys_rmdir
+83	n32	creat				sys_creat
+84	n32	link				sys_link
+85	n32	unlink				sys_unlink
+86	n32	symlink				sys_symlink
+87	n32	readlink			sys_readlink
+88	n32	chmod				sys_chmod
+89	n32	fchmod				sys_fchmod
+90	n32	chown				sys_chown
+91	n32	fchown				sys_fchown
+92	n32	lchown				sys_lchown
+93	n32	umask				sys_umask
+94	n32	gettimeofday			compat_sys_gettimeofday
+95	n32	getrlimit			compat_sys_getrlimit
+96	n32	getrusage			compat_sys_getrusage
+97	n32	sysinfo				compat_sys_sysinfo
+98	n32	times				compat_sys_times
+99	n32	ptrace				compat_sys_ptrace
+100	n32	getuid				sys_getuid
+101	n32	syslog				sys_syslog
+102	n32	getgid				sys_getgid
+103	n32	setuid				sys_setuid
+104	n32	setgid				sys_setgid
+105	n32	geteuid				sys_geteuid
+106	n32	getegid				sys_getegid
+107	n32	setpgid				sys_setpgid
+108	n32	getppid				sys_getppid
+109	n32	getpgrp				sys_getpgrp
+110	n32	setsid				sys_setsid
+111	n32	setreuid			sys_setreuid
+112	n32	setregid			sys_setregid
+113	n32	getgroups			sys_getgroups
+114	n32	setgroups			sys_setgroups
+115	n32	setresuid			sys_setresuid
+116	n32	getresuid			sys_getresuid
+117	n32	setresgid			sys_setresgid
+118	n32	getresgid			sys_getresgid
+119	n32	getpgid				sys_getpgid
+120	n32	setfsuid			sys_setfsuid
+121	n32	setfsgid			sys_setfsgid
+122	n32	getsid				sys_getsid
+123	n32	capget				sys_capget
+124	n32	capset				sys_capset
+125	n32	rt_sigpending			compat_sys_rt_sigpending
+126	n32	rt_sigtimedwait			compat_sys_rt_sigtimedwait_time32
+127	n32	rt_sigqueueinfo			compat_sys_rt_sigqueueinfo
+128	n32	rt_sigsuspend			compat_sys_rt_sigsuspend
+129	n32	sigaltstack			compat_sys_sigaltstack
+130	n32	utime				sys_utime32
+131	n32	mknod				sys_mknod
+132	n32	personality			sys_32_personality
+133	n32	ustat				compat_sys_ustat
+134	n32	statfs				compat_sys_statfs
+135	n32	fstatfs				compat_sys_fstatfs
+136	n32	sysfs				sys_sysfs
+137	n32	getpriority			sys_getpriority
+138	n32	setpriority			sys_setpriority
+139	n32	sched_setparam			sys_sched_setparam
+140	n32	sched_getparam			sys_sched_getparam
+141	n32	sched_setscheduler		sys_sched_setscheduler
+142	n32	sched_getscheduler		sys_sched_getscheduler
+143	n32	sched_get_priority_max		sys_sched_get_priority_max
+144	n32	sched_get_priority_min		sys_sched_get_priority_min
+145	n32	sched_rr_get_interval		sys_sched_rr_get_interval_time32
+146	n32	mlock				sys_mlock
+147	n32	munlock				sys_munlock
+148	n32	mlockall			sys_mlockall
+149	n32	munlockall			sys_munlockall
+150	n32	vhangup				sys_vhangup
+151	n32	pivot_root			sys_pivot_root
+152	n32	_sysctl				sys_ni_syscall
+153	n32	prctl				sys_prctl
+154	n32	adjtimex			sys_adjtimex_time32
+155	n32	setrlimit			compat_sys_setrlimit
+156	n32	chroot				sys_chroot
+157	n32	sync				sys_sync
+158	n32	acct				sys_acct
+159	n32	settimeofday			compat_sys_settimeofday
+160	n32	mount				sys_mount
+161	n32	umount2				sys_umount
+162	n32	swapon				sys_swapon
+163	n32	swapoff				sys_swapoff
+164	n32	reboot				sys_reboot
+165	n32	sethostname			sys_sethostname
+166	n32	setdomainname			sys_setdomainname
+167	n32	create_module			sys_ni_syscall
+168	n32	init_module			sys_init_module
+169	n32	delete_module			sys_delete_module
+170	n32	get_kernel_syms			sys_ni_syscall
+171	n32	query_module			sys_ni_syscall
+172	n32	quotactl			sys_quotactl
+173	n32	nfsservctl			sys_ni_syscall
+174	n32	getpmsg				sys_ni_syscall
+175	n32	putpmsg				sys_ni_syscall
+176	n32	afs_syscall			sys_ni_syscall
+# 177 reserved for security
+177	n32	reserved177			sys_ni_syscall
+178	n32	gettid				sys_gettid
+179	n32	readahead			sys_readahead
+180	n32	setxattr			sys_setxattr
+181	n32	lsetxattr			sys_lsetxattr
+182	n32	fsetxattr			sys_fsetxattr
+183	n32	getxattr			sys_getxattr
+184	n32	lgetxattr			sys_lgetxattr
+185	n32	fgetxattr			sys_fgetxattr
+186	n32	listxattr			sys_listxattr
+187	n32	llistxattr			sys_llistxattr
+188	n32	flistxattr			sys_flistxattr
+189	n32	removexattr			sys_removexattr
+190	n32	lremovexattr			sys_lremovexattr
+191	n32	fremovexattr			sys_fremovexattr
+192	n32	tkill				sys_tkill
+193	n32	reserved193			sys_ni_syscall
+194	n32	futex				sys_futex_time32
+195	n32	sched_setaffinity		compat_sys_sched_setaffinity
+196	n32	sched_getaffinity		compat_sys_sched_getaffinity
+197	n32	cacheflush			sys_cacheflush
+198	n32	cachectl			sys_cachectl
+199	n32	sysmips				__sys_sysmips
+200	n32	io_setup			compat_sys_io_setup
+201	n32	io_destroy			sys_io_destroy
+202	n32	io_getevents			sys_io_getevents_time32
+203	n32	io_submit			compat_sys_io_submit
+204	n32	io_cancel			sys_io_cancel
+205	n32	exit_group			sys_exit_group
+206	n32	lookup_dcookie			sys_lookup_dcookie
+207	n32	epoll_create			sys_epoll_create
+208	n32	epoll_ctl			sys_epoll_ctl
+209	n32	epoll_wait			sys_epoll_wait
+210	n32	remap_file_pages		sys_remap_file_pages
+211	n32	rt_sigreturn			sysn32_rt_sigreturn
+212	n32	fcntl64				compat_sys_fcntl64
+213	n32	set_tid_address			sys_set_tid_address
+214	n32	restart_syscall			sys_restart_syscall
+215	n32	semtimedop			sys_semtimedop_time32
+216	n32	fadvise64			sys_fadvise64_64
+217	n32	statfs64			compat_sys_statfs64
+218	n32	fstatfs64			compat_sys_fstatfs64
+219	n32	sendfile64			sys_sendfile64
+220	n32	timer_create			compat_sys_timer_create
+221	n32	timer_settime			sys_timer_settime32
+222	n32	timer_gettime			sys_timer_gettime32
+223	n32	timer_getoverrun		sys_timer_getoverrun
+224	n32	timer_delete			sys_timer_delete
+225	n32	clock_settime			sys_clock_settime32
+226	n32	clock_gettime			sys_clock_gettime32
+227	n32	clock_getres			sys_clock_getres_time32
+228	n32	clock_nanosleep			sys_clock_nanosleep_time32
+229	n32	tgkill				sys_tgkill
+230	n32	utimes				sys_utimes_time32
+231	n32	mbind				sys_mbind
+232	n32	get_mempolicy			sys_get_mempolicy
+233	n32	set_mempolicy			sys_set_mempolicy
+234	n32	mq_open				compat_sys_mq_open
+235	n32	mq_unlink			sys_mq_unlink
+236	n32	mq_timedsend			sys_mq_timedsend_time32
+237	n32	mq_timedreceive			sys_mq_timedreceive_time32
+238	n32	mq_notify			compat_sys_mq_notify
+239	n32	mq_getsetattr			compat_sys_mq_getsetattr
+240	n32	vserver				sys_ni_syscall
+241	n32	waitid				compat_sys_waitid
+# 242 was sys_setaltroot
+243	n32	add_key				sys_add_key
+244	n32	request_key			sys_request_key
+245	n32	keyctl				compat_sys_keyctl
+246	n32	set_thread_area			sys_set_thread_area
+247	n32	inotify_init			sys_inotify_init
+248	n32	inotify_add_watch		sys_inotify_add_watch
+249	n32	inotify_rm_watch		sys_inotify_rm_watch
+250	n32	migrate_pages			sys_migrate_pages
+251	n32	openat				sys_openat
+252	n32	mkdirat				sys_mkdirat
+253	n32	mknodat				sys_mknodat
+254	n32	fchownat			sys_fchownat
+255	n32	futimesat			sys_futimesat_time32
+256	n32	newfstatat			sys_newfstatat
+257	n32	unlinkat			sys_unlinkat
+258	n32	renameat			sys_renameat
+259	n32	linkat				sys_linkat
+260	n32	symlinkat			sys_symlinkat
+261	n32	readlinkat			sys_readlinkat
+262	n32	fchmodat			sys_fchmodat
+263	n32	faccessat			sys_faccessat
+264	n32	pselect6			compat_sys_pselect6_time32
+265	n32	ppoll				compat_sys_ppoll_time32
+266	n32	unshare				sys_unshare
+267	n32	splice				sys_splice
+268	n32	sync_file_range			sys_sync_file_range
+269	n32	tee				sys_tee
+270	n32	vmsplice			sys_vmsplice
+271	n32	move_pages			sys_move_pages
+272	n32	set_robust_list			compat_sys_set_robust_list
+273	n32	get_robust_list			compat_sys_get_robust_list
+274	n32	kexec_load			compat_sys_kexec_load
+275	n32	getcpu				sys_getcpu
+276	n32	epoll_pwait			compat_sys_epoll_pwait
+277	n32	ioprio_set			sys_ioprio_set
+278	n32	ioprio_get			sys_ioprio_get
+279	n32	utimensat			sys_utimensat_time32
+280	n32	signalfd			compat_sys_signalfd
+281	n32	timerfd				sys_ni_syscall
+282	n32	eventfd				sys_eventfd
+283	n32	fallocate			sys_fallocate
+284	n32	timerfd_create			sys_timerfd_create
+285	n32	timerfd_gettime			sys_timerfd_gettime32
+286	n32	timerfd_settime			sys_timerfd_settime32
+287	n32	signalfd4			compat_sys_signalfd4
+288	n32	eventfd2			sys_eventfd2
+289	n32	epoll_create1			sys_epoll_create1
+290	n32	dup3				sys_dup3
+291	n32	pipe2				sys_pipe2
+292	n32	inotify_init1			sys_inotify_init1
+293	n32	preadv				compat_sys_preadv
+294	n32	pwritev				compat_sys_pwritev
+295	n32	rt_tgsigqueueinfo		compat_sys_rt_tgsigqueueinfo
+296	n32	perf_event_open			sys_perf_event_open
+297	n32	accept4				sys_accept4
+298	n32	recvmmsg			compat_sys_recvmmsg_time32
+299	n32	getdents64			sys_getdents64
+300	n32	fanotify_init			sys_fanotify_init
+301	n32	fanotify_mark			sys_fanotify_mark
+302	n32	prlimit64			sys_prlimit64
+303	n32	name_to_handle_at		sys_name_to_handle_at
+304	n32	open_by_handle_at		sys_open_by_handle_at
+305	n32	clock_adjtime			sys_clock_adjtime32
+306	n32	syncfs				sys_syncfs
+307	n32	sendmmsg			compat_sys_sendmmsg
+308	n32	setns				sys_setns
+309	n32	process_vm_readv		sys_process_vm_readv
+310	n32	process_vm_writev		sys_process_vm_writev
+311	n32	kcmp				sys_kcmp
+312	n32	finit_module			sys_finit_module
+313	n32	sched_setattr			sys_sched_setattr
+314	n32	sched_getattr			sys_sched_getattr
+315	n32	renameat2			sys_renameat2
+316	n32	seccomp				sys_seccomp
+317	n32	getrandom			sys_getrandom
+318	n32	memfd_create			sys_memfd_create
+319	n32	bpf				sys_bpf
+320	n32	execveat			compat_sys_execveat
+321	n32	userfaultfd			sys_userfaultfd
+322	n32	membarrier			sys_membarrier
+323	n32	mlock2				sys_mlock2
+324	n32	copy_file_range			sys_copy_file_range
+325	n32	preadv2				compat_sys_preadv2
+326	n32	pwritev2			compat_sys_pwritev2
+327	n32	pkey_mprotect			sys_pkey_mprotect
+328	n32	pkey_alloc			sys_pkey_alloc
+329	n32	pkey_free			sys_pkey_free
+330	n32	statx				sys_statx
+331	n32	rseq				sys_rseq
+332	n32	io_pgetevents			compat_sys_io_pgetevents
+# 333 through 402 are unassigned to sync up with generic numbers
+403	n32	clock_gettime64			sys_clock_gettime
+404	n32	clock_settime64			sys_clock_settime
+405	n32	clock_adjtime64			sys_clock_adjtime
+406	n32	clock_getres_time64		sys_clock_getres
+407	n32	clock_nanosleep_time64		sys_clock_nanosleep
+408	n32	timer_gettime64			sys_timer_gettime
+409	n32	timer_settime64			sys_timer_settime
+410	n32	timerfd_gettime64		sys_timerfd_gettime
+411	n32	timerfd_settime64		sys_timerfd_settime
+412	n32	utimensat_time64		sys_utimensat
+413	n32	pselect6_time64			compat_sys_pselect6_time64
+414	n32	ppoll_time64			compat_sys_ppoll_time64
+416	n32	io_pgetevents_time64		sys_io_pgetevents
+417	n32	recvmmsg_time64			compat_sys_recvmmsg_time64
+418	n32	mq_timedsend_time64		sys_mq_timedsend
+419	n32	mq_timedreceive_time64		sys_mq_timedreceive
+420	n32	semtimedop_time64		sys_semtimedop
+421	n32	rt_sigtimedwait_time64		compat_sys_rt_sigtimedwait_time64
+422	n32	futex_time64			sys_futex
+423	n32	sched_rr_get_interval_time64	sys_sched_rr_get_interval
+424	n32	pidfd_send_signal		sys_pidfd_send_signal
+425	n32	io_uring_setup			sys_io_uring_setup
+426	n32	io_uring_enter			sys_io_uring_enter
+427	n32	io_uring_register		sys_io_uring_register
+428	n32	open_tree			sys_open_tree
+429	n32	move_mount			sys_move_mount
+430	n32	fsopen				sys_fsopen
+431	n32	fsconfig			sys_fsconfig
+432	n32	fsmount				sys_fsmount
+433	n32	fspick				sys_fspick
+434	n32	pidfd_open			sys_pidfd_open
+435	n32	clone3				__sys_clone3
+436	n32	close_range			sys_close_range
+437	n32	openat2				sys_openat2
+438	n32	pidfd_getfd			sys_pidfd_getfd
+439	n32	faccessat2			sys_faccessat2
+440	n32	process_madvise			sys_process_madvise
+441	n32	epoll_pwait2			compat_sys_epoll_pwait2
+442	n32	mount_setattr			sys_mount_setattr
+443	n32	quotactl_fd			sys_quotactl_fd
+444	n32	landlock_create_ruleset		sys_landlock_create_ruleset
+445	n32	landlock_add_rule		sys_landlock_add_rule
+446	n32	landlock_restrict_self		sys_landlock_restrict_self
+# 447 reserved for memfd_secret
+448	n32	process_mrelease		sys_process_mrelease
+449	n32	futex_waitv			sys_futex_waitv
+450	n32	set_mempolicy_home_node		sys_set_mempolicy_home_node
diff --git a/arch/mips/kernel/syscalls/syscall_n64.tbl b/arch/mips/kernel/syscalls/syscall_n64.tbl
new file mode 100644
index 000000000..3f1886ad9
--- /dev/null
+++ b/arch/mips/kernel/syscalls/syscall_n64.tbl
@@ -0,0 +1,367 @@
+# SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note
+#
+# system call numbers and entry vectors for mips
+#
+# The format is:
+# <number> <abi> <name> <entry point>
+#
+# The <abi> is always "n64" for this file.
+#
+0	n64	read				sys_read
+1	n64	write				sys_write
+2	n64	open				sys_open
+3	n64	close				sys_close
+4	n64	stat				sys_newstat
+5	n64	fstat				sys_newfstat
+6	n64	lstat				sys_newlstat
+7	n64	poll				sys_poll
+8	n64	lseek				sys_lseek
+9	n64	mmap				sys_mips_mmap
+10	n64	mprotect			sys_mprotect
+11	n64	munmap				sys_munmap
+12	n64	brk				sys_brk
+13	n64	rt_sigaction			sys_rt_sigaction
+14	n64	rt_sigprocmask			sys_rt_sigprocmask
+15	n64	ioctl				sys_ioctl
+16	n64	pread64				sys_pread64
+17	n64	pwrite64			sys_pwrite64
+18	n64	readv				sys_readv
+19	n64	writev				sys_writev
+20	n64	access				sys_access
+21	n64	pipe				sysm_pipe
+22	n64	_newselect			sys_select
+23	n64	sched_yield			sys_sched_yield
+24	n64	mremap				sys_mremap
+25	n64	msync				sys_msync
+26	n64	mincore				sys_mincore
+27	n64	madvise				sys_madvise
+28	n64	shmget				sys_shmget
+29	n64	shmat				sys_shmat
+30	n64	shmctl				sys_old_shmctl
+31	n64	dup				sys_dup
+32	n64	dup2				sys_dup2
+33	n64	pause				sys_pause
+34	n64	nanosleep			sys_nanosleep
+35	n64	getitimer			sys_getitimer
+36	n64	setitimer			sys_setitimer
+37	n64	alarm				sys_alarm
+38	n64	getpid				sys_getpid
+39	n64	sendfile			sys_sendfile64
+40	n64	socket				sys_socket
+41	n64	connect				sys_connect
+42	n64	accept				sys_accept
+43	n64	sendto				sys_sendto
+44	n64	recvfrom			sys_recvfrom
+45	n64	sendmsg				sys_sendmsg
+46	n64	recvmsg				sys_recvmsg
+47	n64	shutdown			sys_shutdown
+48	n64	bind				sys_bind
+49	n64	listen				sys_listen
+50	n64	getsockname			sys_getsockname
+51	n64	getpeername			sys_getpeername
+52	n64	socketpair			sys_socketpair
+53	n64	setsockopt			sys_setsockopt
+54	n64	getsockopt			sys_getsockopt
+55	n64	clone				__sys_clone
+56	n64	fork				__sys_fork
+57	n64	execve				sys_execve
+58	n64	exit				sys_exit
+59	n64	wait4				sys_wait4
+60	n64	kill				sys_kill
+61	n64	uname				sys_newuname
+62	n64	semget				sys_semget
+63	n64	semop				sys_semop
+64	n64	semctl				sys_old_semctl
+65	n64	shmdt				sys_shmdt
+66	n64	msgget				sys_msgget
+67	n64	msgsnd				sys_msgsnd
+68	n64	msgrcv				sys_msgrcv
+69	n64	msgctl				sys_old_msgctl
+70	n64	fcntl				sys_fcntl
+71	n64	flock				sys_flock
+72	n64	fsync				sys_fsync
+73	n64	fdatasync			sys_fdatasync
+74	n64	truncate			sys_truncate
+75	n64	ftruncate			sys_ftruncate
+76	n64	getdents			sys_getdents
+77	n64	getcwd				sys_getcwd
+78	n64	chdir				sys_chdir
+79	n64	fchdir				sys_fchdir
+80	n64	rename				sys_rename
+81	n64	mkdir				sys_mkdir
+82	n64	rmdir				sys_rmdir
+83	n64	creat				sys_creat
+84	n64	link				sys_link
+85	n64	unlink				sys_unlink
+86	n64	symlink				sys_symlink
+87	n64	readlink			sys_readlink
+88	n64	chmod				sys_chmod
+89	n64	fchmod				sys_fchmod
+90	n64	chown				sys_chown
+91	n64	fchown				sys_fchown
+92	n64	lchown				sys_lchown
+93	n64	umask				sys_umask
+94	n64	gettimeofday			sys_gettimeofday
+95	n64	getrlimit			sys_getrlimit
+96	n64	getrusage			sys_getrusage
+97	n64	sysinfo				sys_sysinfo
+98	n64	times				sys_times
+99	n64	ptrace				sys_ptrace
+100	n64	getuid				sys_getuid
+101	n64	syslog				sys_syslog
+102	n64	getgid				sys_getgid
+103	n64	setuid				sys_setuid
+104	n64	setgid				sys_setgid
+105	n64	geteuid				sys_geteuid
+106	n64	getegid				sys_getegid
+107	n64	setpgid				sys_setpgid
+108	n64	getppid				sys_getppid
+109	n64	getpgrp				sys_getpgrp
+110	n64	setsid				sys_setsid
+111	n64	setreuid			sys_setreuid
+112	n64	setregid			sys_setregid
+113	n64	getgroups			sys_getgroups
+114	n64	setgroups			sys_setgroups
+115	n64	setresuid			sys_setresuid
+116	n64	getresuid			sys_getresuid
+117	n64	setresgid			sys_setresgid
+118	n64	getresgid			sys_getresgid
+119	n64	getpgid				sys_getpgid
+120	n64	setfsuid			sys_setfsuid
+121	n64	setfsgid			sys_setfsgid
+122	n64	getsid				sys_getsid
+123	n64	capget				sys_capget
+124	n64	capset				sys_capset
+125	n64	rt_sigpending			sys_rt_sigpending
+126	n64	rt_sigtimedwait			sys_rt_sigtimedwait
+127	n64	rt_sigqueueinfo			sys_rt_sigqueueinfo
+128	n64	rt_sigsuspend			sys_rt_sigsuspend
+129	n64	sigaltstack			sys_sigaltstack
+130	n64	utime				sys_utime
+131	n64	mknod				sys_mknod
+132	n64	personality			sys_personality
+133	n64	ustat				sys_ustat
+134	n64	statfs				sys_statfs
+135	n64	fstatfs				sys_fstatfs
+136	n64	sysfs				sys_sysfs
+137	n64	getpriority			sys_getpriority
+138	n64	setpriority			sys_setpriority
+139	n64	sched_setparam			sys_sched_setparam
+140	n64	sched_getparam			sys_sched_getparam
+141	n64	sched_setscheduler		sys_sched_setscheduler
+142	n64	sched_getscheduler		sys_sched_getscheduler
+143	n64	sched_get_priority_max		sys_sched_get_priority_max
+144	n64	sched_get_priority_min		sys_sched_get_priority_min
+145	n64	sched_rr_get_interval		sys_sched_rr_get_interval
+146	n64	mlock				sys_mlock
+147	n64	munlock				sys_munlock
+148	n64	mlockall			sys_mlockall
+149	n64	munlockall			sys_munlockall
+150	n64	vhangup				sys_vhangup
+151	n64	pivot_root			sys_pivot_root
+152	n64	_sysctl				sys_ni_syscall
+153	n64	prctl				sys_prctl
+154	n64	adjtimex			sys_adjtimex
+155	n64	setrlimit			sys_setrlimit
+156	n64	chroot				sys_chroot
+157	n64	sync				sys_sync
+158	n64	acct				sys_acct
+159	n64	settimeofday			sys_settimeofday
+160	n64	mount				sys_mount
+161	n64	umount2				sys_umount
+162	n64	swapon				sys_swapon
+163	n64	swapoff				sys_swapoff
+164	n64	reboot				sys_reboot
+165	n64	sethostname			sys_sethostname
+166	n64	setdomainname			sys_setdomainname
+167	n64	create_module			sys_ni_syscall
+168	n64	init_module			sys_init_module
+169	n64	delete_module			sys_delete_module
+170	n64	get_kernel_syms			sys_ni_syscall
+171	n64	query_module			sys_ni_syscall
+172	n64	quotactl			sys_quotactl
+173	n64	nfsservctl			sys_ni_syscall
+174	n64	getpmsg				sys_ni_syscall
+175	n64	putpmsg				sys_ni_syscall
+176	n64	afs_syscall			sys_ni_syscall
+# 177 reserved for security
+177	n64	reserved177			sys_ni_syscall
+178	n64	gettid				sys_gettid
+179	n64	readahead			sys_readahead
+180	n64	setxattr			sys_setxattr
+181	n64	lsetxattr			sys_lsetxattr
+182	n64	fsetxattr			sys_fsetxattr
+183	n64	getxattr			sys_getxattr
+184	n64	lgetxattr			sys_lgetxattr
+185	n64	fgetxattr			sys_fgetxattr
+186	n64	listxattr			sys_listxattr
+187	n64	llistxattr			sys_llistxattr
+188	n64	flistxattr			sys_flistxattr
+189	n64	removexattr			sys_removexattr
+190	n64	lremovexattr			sys_lremovexattr
+191	n64	fremovexattr			sys_fremovexattr
+192	n64	tkill				sys_tkill
+193	n64	reserved193			sys_ni_syscall
+194	n64	futex				sys_futex
+195	n64	sched_setaffinity		sys_sched_setaffinity
+196	n64	sched_getaffinity		sys_sched_getaffinity
+197	n64	cacheflush			sys_cacheflush
+198	n64	cachectl			sys_cachectl
+199	n64	sysmips				__sys_sysmips
+200	n64	io_setup			sys_io_setup
+201	n64	io_destroy			sys_io_destroy
+202	n64	io_getevents			sys_io_getevents
+203	n64	io_submit			sys_io_submit
+204	n64	io_cancel			sys_io_cancel
+205	n64	exit_group			sys_exit_group
+206	n64	lookup_dcookie			sys_lookup_dcookie
+207	n64	epoll_create			sys_epoll_create
+208	n64	epoll_ctl			sys_epoll_ctl
+209	n64	epoll_wait			sys_epoll_wait
+210	n64	remap_file_pages		sys_remap_file_pages
+211	n64	rt_sigreturn			sys_rt_sigreturn
+212	n64	set_tid_address			sys_set_tid_address
+213	n64	restart_syscall			sys_restart_syscall
+214	n64	semtimedop			sys_semtimedop
+215	n64	fadvise64			sys_fadvise64_64
+216	n64	timer_create			sys_timer_create
+217	n64	timer_settime			sys_timer_settime
+218	n64	timer_gettime			sys_timer_gettime
+219	n64	timer_getoverrun		sys_timer_getoverrun
+220	n64	timer_delete			sys_timer_delete
+221	n64	clock_settime			sys_clock_settime
+222	n64	clock_gettime			sys_clock_gettime
+223	n64	clock_getres			sys_clock_getres
+224	n64	clock_nanosleep			sys_clock_nanosleep
+225	n64	tgkill				sys_tgkill
+226	n64	utimes				sys_utimes
+227	n64	mbind				sys_mbind
+228	n64	get_mempolicy			sys_get_mempolicy
+229	n64	set_mempolicy			sys_set_mempolicy
+230	n64	mq_open				sys_mq_open
+231	n64	mq_unlink			sys_mq_unlink
+232	n64	mq_timedsend			sys_mq_timedsend
+233	n64	mq_timedreceive			sys_mq_timedreceive
+234	n64	mq_notify			sys_mq_notify
+235	n64	mq_getsetattr			sys_mq_getsetattr
+236	n64	vserver				sys_ni_syscall
+237	n64	waitid				sys_waitid
+# 238 was sys_setaltroot
+239	n64	add_key				sys_add_key
+240	n64	request_key			sys_request_key
+241	n64	keyctl				sys_keyctl
+242	n64	set_thread_area			sys_set_thread_area
+243	n64	inotify_init			sys_inotify_init
+244	n64	inotify_add_watch		sys_inotify_add_watch
+245	n64	inotify_rm_watch		sys_inotify_rm_watch
+246	n64	migrate_pages			sys_migrate_pages
+247	n64	openat				sys_openat
+248	n64	mkdirat				sys_mkdirat
+249	n64	mknodat				sys_mknodat
+250	n64	fchownat			sys_fchownat
+251	n64	futimesat			sys_futimesat
+252	n64	newfstatat			sys_newfstatat
+253	n64	unlinkat			sys_unlinkat
+254	n64	renameat			sys_renameat
+255	n64	linkat				sys_linkat
+256	n64	symlinkat			sys_symlinkat
+257	n64	readlinkat			sys_readlinkat
+258	n64	fchmodat			sys_fchmodat
+259	n64	faccessat			sys_faccessat
+260	n64	pselect6			sys_pselect6
+261	n64	ppoll				sys_ppoll
+262	n64	unshare				sys_unshare
+263	n64	splice				sys_splice
+264	n64	sync_file_range			sys_sync_file_range
+265	n64	tee				sys_tee
+266	n64	vmsplice			sys_vmsplice
+267	n64	move_pages			sys_move_pages
+268	n64	set_robust_list			sys_set_robust_list
+269	n64	get_robust_list			sys_get_robust_list
+270	n64	kexec_load			sys_kexec_load
+271	n64	getcpu				sys_getcpu
+272	n64	epoll_pwait			sys_epoll_pwait
+273	n64	ioprio_set			sys_ioprio_set
+274	n64	ioprio_get			sys_ioprio_get
+275	n64	utimensat			sys_utimensat
+276	n64	signalfd			sys_signalfd
+277	n64	timerfd				sys_ni_syscall
+278	n64	eventfd				sys_eventfd
+279	n64	fallocate			sys_fallocate
+280	n64	timerfd_create			sys_timerfd_create
+281	n64	timerfd_gettime			sys_timerfd_gettime
+282	n64	timerfd_settime			sys_timerfd_settime
+283	n64	signalfd4			sys_signalfd4
+284	n64	eventfd2			sys_eventfd2
+285	n64	epoll_create1			sys_epoll_create1
+286	n64	dup3				sys_dup3
+287	n64	pipe2				sys_pipe2
+288	n64	inotify_init1			sys_inotify_init1
+289	n64	preadv				sys_preadv
+290	n64	pwritev				sys_pwritev
+291	n64	rt_tgsigqueueinfo		sys_rt_tgsigqueueinfo
+292	n64	perf_event_open			sys_perf_event_open
+293	n64	accept4				sys_accept4
+294	n64	recvmmsg			sys_recvmmsg
+295	n64	fanotify_init			sys_fanotify_init
+296	n64	fanotify_mark			sys_fanotify_mark
+297	n64	prlimit64			sys_prlimit64
+298	n64	name_to_handle_at		sys_name_to_handle_at
+299	n64	open_by_handle_at		sys_open_by_handle_at
+300	n64	clock_adjtime			sys_clock_adjtime
+301	n64	syncfs				sys_syncfs
+302	n64	sendmmsg			sys_sendmmsg
+303	n64	setns				sys_setns
+304	n64	process_vm_readv		sys_process_vm_readv
+305	n64	process_vm_writev		sys_process_vm_writev
+306	n64	kcmp				sys_kcmp
+307	n64	finit_module			sys_finit_module
+308	n64	getdents64			sys_getdents64
+309	n64	sched_setattr			sys_sched_setattr
+310	n64	sched_getattr			sys_sched_getattr
+311	n64	renameat2			sys_renameat2
+312	n64	seccomp				sys_seccomp
+313	n64	getrandom			sys_getrandom
+314	n64	memfd_create			sys_memfd_create
+315	n64	bpf				sys_bpf
+316	n64	execveat			sys_execveat
+317	n64	userfaultfd			sys_userfaultfd
+318	n64	membarrier			sys_membarrier
+319	n64	mlock2				sys_mlock2
+320	n64	copy_file_range			sys_copy_file_range
+321	n64	preadv2				sys_preadv2
+322	n64	pwritev2			sys_pwritev2
+323	n64	pkey_mprotect			sys_pkey_mprotect
+324	n64	pkey_alloc			sys_pkey_alloc
+325	n64	pkey_free			sys_pkey_free
+326	n64	statx				sys_statx
+327	n64	rseq				sys_rseq
+328	n64	io_pgetevents			sys_io_pgetevents
+# 329 through 423 are reserved to sync up with other architectures
+424	n64	pidfd_send_signal		sys_pidfd_send_signal
+425	n64	io_uring_setup			sys_io_uring_setup
+426	n64	io_uring_enter			sys_io_uring_enter
+427	n64	io_uring_register		sys_io_uring_register
+428	n64	open_tree			sys_open_tree
+429	n64	move_mount			sys_move_mount
+430	n64	fsopen				sys_fsopen
+431	n64	fsconfig			sys_fsconfig
+432	n64	fsmount				sys_fsmount
+433	n64	fspick				sys_fspick
+434	n64	pidfd_open			sys_pidfd_open
+435	n64	clone3				__sys_clone3
+436	n64	close_range			sys_close_range
+437	n64	openat2				sys_openat2
+438	n64	pidfd_getfd			sys_pidfd_getfd
+439	n64	faccessat2			sys_faccessat2
+440	n64	process_madvise			sys_process_madvise
+441	n64	epoll_pwait2			sys_epoll_pwait2
+442	n64	mount_setattr			sys_mount_setattr
+443	n64	quotactl_fd			sys_quotactl_fd
+444	n64	landlock_create_ruleset		sys_landlock_create_ruleset
+445	n64	landlock_add_rule		sys_landlock_add_rule
+446	n64	landlock_restrict_self		sys_landlock_restrict_self
+# 447 reserved for memfd_secret
+448	n64	process_mrelease		sys_process_mrelease
+449	n64	futex_waitv			sys_futex_waitv
+450	common	set_mempolicy_home_node		sys_set_mempolicy_home_node
diff --git a/arch/mips/kernel/syscalls/syscall_o32.tbl b/arch/mips/kernel/syscalls/syscall_o32.tbl
new file mode 100644
index 000000000..8f243e35a
--- /dev/null
+++ b/arch/mips/kernel/syscalls/syscall_o32.tbl
@@ -0,0 +1,440 @@
+# SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note
+#
+# system call numbers and entry vectors for mips
+#
+# The format is:
+# <number> <abi> <name> <entry point> <compat entry point>
+#
+# The <abi> is always "o32" for this file.
+#
+0	o32	syscall				sys_syscall			sys32_syscall
+1	o32	exit				sys_exit
+2	o32	fork				__sys_fork
+3	o32	read				sys_read
+4	o32	write				sys_write
+5	o32	open				sys_open			compat_sys_open
+6	o32	close				sys_close
+7	o32	waitpid				sys_waitpid
+8	o32	creat				sys_creat
+9	o32	link				sys_link
+10	o32	unlink				sys_unlink
+11	o32	execve				sys_execve			compat_sys_execve
+12	o32	chdir				sys_chdir
+13	o32	time				sys_time32
+14	o32	mknod				sys_mknod
+15	o32	chmod				sys_chmod
+16	o32	lchown				sys_lchown
+17	o32	break				sys_ni_syscall
+# 18 was sys_stat
+18	o32	unused18			sys_ni_syscall
+19	o32	lseek				sys_lseek
+20	o32	getpid				sys_getpid
+21	o32	mount				sys_mount
+22	o32	umount				sys_oldumount
+23	o32	setuid				sys_setuid
+24	o32	getuid				sys_getuid
+25	o32	stime				sys_stime32
+26	o32	ptrace				sys_ptrace			compat_sys_ptrace
+27	o32	alarm				sys_alarm
+# 28 was sys_fstat
+28	o32	unused28			sys_ni_syscall
+29	o32	pause				sys_pause
+30	o32	utime				sys_utime32
+31	o32	stty				sys_ni_syscall
+32	o32	gtty				sys_ni_syscall
+33	o32	access				sys_access
+34	o32	nice				sys_nice
+35	o32	ftime				sys_ni_syscall
+36	o32	sync				sys_sync
+37	o32	kill				sys_kill
+38	o32	rename				sys_rename
+39	o32	mkdir				sys_mkdir
+40	o32	rmdir				sys_rmdir
+41	o32	dup				sys_dup
+42	o32	pipe				sysm_pipe
+43	o32	times				sys_times			compat_sys_times
+44	o32	prof				sys_ni_syscall
+45	o32	brk				sys_brk
+46	o32	setgid				sys_setgid
+47	o32	getgid				sys_getgid
+48	o32	signal				sys_ni_syscall
+49	o32	geteuid				sys_geteuid
+50	o32	getegid				sys_getegid
+51	o32	acct				sys_acct
+52	o32	umount2				sys_umount
+53	o32	lock				sys_ni_syscall
+54	o32	ioctl				sys_ioctl			compat_sys_ioctl
+55	o32	fcntl				sys_fcntl			compat_sys_fcntl
+56	o32	mpx				sys_ni_syscall
+57	o32	setpgid				sys_setpgid
+58	o32	ulimit				sys_ni_syscall
+59	o32	unused59			sys_olduname
+60	o32	umask				sys_umask
+61	o32	chroot				sys_chroot
+62	o32	ustat				sys_ustat			compat_sys_ustat
+63	o32	dup2				sys_dup2
+64	o32	getppid				sys_getppid
+65	o32	getpgrp				sys_getpgrp
+66	o32	setsid				sys_setsid
+67	o32	sigaction			sys_sigaction			sys_32_sigaction
+68	o32	sgetmask			sys_sgetmask
+69	o32	ssetmask			sys_ssetmask
+70	o32	setreuid			sys_setreuid
+71	o32	setregid			sys_setregid
+72	o32	sigsuspend			sys_sigsuspend			sys32_sigsuspend
+73	o32	sigpending			sys_sigpending			compat_sys_sigpending
+74	o32	sethostname			sys_sethostname
+75	o32	setrlimit			sys_setrlimit			compat_sys_setrlimit
+76	o32	getrlimit			sys_getrlimit			compat_sys_getrlimit
+77	o32	getrusage			sys_getrusage			compat_sys_getrusage
+78	o32	gettimeofday			sys_gettimeofday		compat_sys_gettimeofday
+79	o32	settimeofday			sys_settimeofday		compat_sys_settimeofday
+80	o32	getgroups			sys_getgroups
+81	o32	setgroups			sys_setgroups
+# 82 was old_select
+82	o32	reserved82			sys_ni_syscall
+83	o32	symlink				sys_symlink
+# 84 was sys_lstat
+84	o32	unused84			sys_ni_syscall
+85	o32	readlink			sys_readlink
+86	o32	uselib				sys_uselib
+87	o32	swapon				sys_swapon
+88	o32	reboot				sys_reboot
+89	o32	readdir				sys_old_readdir			compat_sys_old_readdir
+90	o32	mmap				sys_mips_mmap
+91	o32	munmap				sys_munmap
+92	o32	truncate			sys_truncate			compat_sys_truncate
+93	o32	ftruncate			sys_ftruncate			compat_sys_ftruncate
+94	o32	fchmod				sys_fchmod
+95	o32	fchown				sys_fchown
+96	o32	getpriority			sys_getpriority
+97	o32	setpriority			sys_setpriority
+98	o32	profil				sys_ni_syscall
+99	o32	statfs				sys_statfs			compat_sys_statfs
+100	o32	fstatfs				sys_fstatfs			compat_sys_fstatfs
+101	o32	ioperm				sys_ni_syscall
+102	o32	socketcall			sys_socketcall			compat_sys_socketcall
+103	o32	syslog				sys_syslog
+104	o32	setitimer			sys_setitimer			compat_sys_setitimer
+105	o32	getitimer			sys_getitimer			compat_sys_getitimer
+106	o32	stat				sys_newstat			compat_sys_newstat
+107	o32	lstat				sys_newlstat			compat_sys_newlstat
+108	o32	fstat				sys_newfstat			compat_sys_newfstat
+109	o32	unused109			sys_uname
+110	o32	iopl				sys_ni_syscall
+111	o32	vhangup				sys_vhangup
+112	o32	idle				sys_ni_syscall
+113	o32	vm86				sys_ni_syscall
+114	o32	wait4				sys_wait4			compat_sys_wait4
+115	o32	swapoff				sys_swapoff
+116	o32	sysinfo				sys_sysinfo			compat_sys_sysinfo
+117	o32	ipc				sys_ipc				compat_sys_ipc
+118	o32	fsync				sys_fsync
+119	o32	sigreturn			sys_sigreturn			sys32_sigreturn
+120	o32	clone				__sys_clone
+121	o32	setdomainname			sys_setdomainname
+122	o32	uname				sys_newuname
+123	o32	modify_ldt			sys_ni_syscall
+124	o32	adjtimex			sys_adjtimex_time32
+125	o32	mprotect			sys_mprotect
+126	o32	sigprocmask			sys_sigprocmask			compat_sys_sigprocmask
+127	o32	create_module			sys_ni_syscall
+128	o32	init_module			sys_init_module
+129	o32	delete_module			sys_delete_module
+130	o32	get_kernel_syms			sys_ni_syscall
+131	o32	quotactl			sys_quotactl
+132	o32	getpgid				sys_getpgid
+133	o32	fchdir				sys_fchdir
+134	o32	bdflush				sys_ni_syscall
+135	o32	sysfs				sys_sysfs
+136	o32	personality			sys_personality			sys_32_personality
+137	o32	afs_syscall			sys_ni_syscall
+138	o32	setfsuid			sys_setfsuid
+139	o32	setfsgid			sys_setfsgid
+140	o32	_llseek				sys_llseek			sys_32_llseek
+141	o32	getdents			sys_getdents			compat_sys_getdents
+142	o32	_newselect			sys_select			compat_sys_select
+143	o32	flock				sys_flock
+144	o32	msync				sys_msync
+145	o32	readv				sys_readv
+146	o32	writev				sys_writev
+147	o32	cacheflush			sys_cacheflush
+148	o32	cachectl			sys_cachectl
+149	o32	sysmips				__sys_sysmips
+150	o32	unused150			sys_ni_syscall
+151	o32	getsid				sys_getsid
+152	o32	fdatasync			sys_fdatasync
+153	o32	_sysctl				sys_ni_syscall
+154	o32	mlock				sys_mlock
+155	o32	munlock				sys_munlock
+156	o32	mlockall			sys_mlockall
+157	o32	munlockall			sys_munlockall
+158	o32	sched_setparam			sys_sched_setparam
+159	o32	sched_getparam			sys_sched_getparam
+160	o32	sched_setscheduler		sys_sched_setscheduler
+161	o32	sched_getscheduler		sys_sched_getscheduler
+162	o32	sched_yield			sys_sched_yield
+163	o32	sched_get_priority_max		sys_sched_get_priority_max
+164	o32	sched_get_priority_min		sys_sched_get_priority_min
+165	o32	sched_rr_get_interval		sys_sched_rr_get_interval_time32
+166	o32	nanosleep			sys_nanosleep_time32
+167	o32	mremap				sys_mremap
+168	o32	accept				sys_accept
+169	o32	bind				sys_bind
+170	o32	connect				sys_connect
+171	o32	getpeername			sys_getpeername
+172	o32	getsockname			sys_getsockname
+173	o32	getsockopt			sys_getsockopt			sys_getsockopt
+174	o32	listen				sys_listen
+175	o32	recv				sys_recv			compat_sys_recv
+176	o32	recvfrom			sys_recvfrom			compat_sys_recvfrom
+177	o32	recvmsg				sys_recvmsg			compat_sys_recvmsg
+178	o32	send				sys_send
+179	o32	sendmsg				sys_sendmsg			compat_sys_sendmsg
+180	o32	sendto				sys_sendto
+181	o32	setsockopt			sys_setsockopt			sys_setsockopt
+182	o32	shutdown			sys_shutdown
+183	o32	socket				sys_socket
+184	o32	socketpair			sys_socketpair
+185	o32	setresuid			sys_setresuid
+186	o32	getresuid			sys_getresuid
+187	o32	query_module			sys_ni_syscall
+188	o32	poll				sys_poll
+189	o32	nfsservctl			sys_ni_syscall
+190	o32	setresgid			sys_setresgid
+191	o32	getresgid			sys_getresgid
+192	o32	prctl				sys_prctl
+193	o32	rt_sigreturn			sys_rt_sigreturn		sys32_rt_sigreturn
+194	o32	rt_sigaction			sys_rt_sigaction		compat_sys_rt_sigaction
+195	o32	rt_sigprocmask			sys_rt_sigprocmask		compat_sys_rt_sigprocmask
+196	o32	rt_sigpending			sys_rt_sigpending		compat_sys_rt_sigpending
+197	o32	rt_sigtimedwait			sys_rt_sigtimedwait_time32	compat_sys_rt_sigtimedwait_time32
+198	o32	rt_sigqueueinfo			sys_rt_sigqueueinfo		compat_sys_rt_sigqueueinfo
+199	o32	rt_sigsuspend			sys_rt_sigsuspend		compat_sys_rt_sigsuspend
+200	o32	pread64				sys_pread64			sys_32_pread
+201	o32	pwrite64			sys_pwrite64			sys_32_pwrite
+202	o32	chown				sys_chown
+203	o32	getcwd				sys_getcwd
+204	o32	capget				sys_capget
+205	o32	capset				sys_capset
+206	o32	sigaltstack			sys_sigaltstack			compat_sys_sigaltstack
+207	o32	sendfile			sys_sendfile			compat_sys_sendfile
+208	o32	getpmsg				sys_ni_syscall
+209	o32	putpmsg				sys_ni_syscall
+210	o32	mmap2				sys_mips_mmap2
+211	o32	truncate64			sys_truncate64			sys_32_truncate64
+212	o32	ftruncate64			sys_ftruncate64			sys_32_ftruncate64
+213	o32	stat64				sys_stat64			sys_newstat
+214	o32	lstat64				sys_lstat64			sys_newlstat
+215	o32	fstat64				sys_fstat64			sys_newfstat
+216	o32	pivot_root			sys_pivot_root
+217	o32	mincore				sys_mincore
+218	o32	madvise				sys_madvise
+219	o32	getdents64			sys_getdents64
+220	o32	fcntl64				sys_fcntl64			compat_sys_fcntl64
+221	o32	reserved221			sys_ni_syscall
+222	o32	gettid				sys_gettid
+223	o32	readahead			sys_readahead			sys32_readahead
+224	o32	setxattr			sys_setxattr
+225	o32	lsetxattr			sys_lsetxattr
+226	o32	fsetxattr			sys_fsetxattr
+227	o32	getxattr			sys_getxattr
+228	o32	lgetxattr			sys_lgetxattr
+229	o32	fgetxattr			sys_fgetxattr
+230	o32	listxattr			sys_listxattr
+231	o32	llistxattr			sys_llistxattr
+232	o32	flistxattr			sys_flistxattr
+233	o32	removexattr			sys_removexattr
+234	o32	lremovexattr			sys_lremovexattr
+235	o32	fremovexattr			sys_fremovexattr
+236	o32	tkill				sys_tkill
+237	o32	sendfile64			sys_sendfile64
+238	o32	futex				sys_futex_time32
+239	o32	sched_setaffinity		sys_sched_setaffinity		compat_sys_sched_setaffinity
+240	o32	sched_getaffinity		sys_sched_getaffinity		compat_sys_sched_getaffinity
+241	o32	io_setup			sys_io_setup			compat_sys_io_setup
+242	o32	io_destroy			sys_io_destroy
+243	o32	io_getevents			sys_io_getevents_time32
+244	o32	io_submit			sys_io_submit			compat_sys_io_submit
+245	o32	io_cancel			sys_io_cancel
+246	o32	exit_group			sys_exit_group
+247	o32	lookup_dcookie			sys_lookup_dcookie		compat_sys_lookup_dcookie
+248	o32	epoll_create			sys_epoll_create
+249	o32	epoll_ctl			sys_epoll_ctl
+250	o32	epoll_wait			sys_epoll_wait
+251	o32	remap_file_pages		sys_remap_file_pages
+252	o32	set_tid_address			sys_set_tid_address
+253	o32	restart_syscall			sys_restart_syscall
+254	o32	fadvise64			sys_fadvise64_64		sys32_fadvise64_64
+255	o32	statfs64			sys_statfs64			compat_sys_statfs64
+256	o32	fstatfs64			sys_fstatfs64			compat_sys_fstatfs64
+257	o32	timer_create			sys_timer_create		compat_sys_timer_create
+258	o32	timer_settime			sys_timer_settime32
+259	o32	timer_gettime			sys_timer_gettime32
+260	o32	timer_getoverrun		sys_timer_getoverrun
+261	o32	timer_delete			sys_timer_delete
+262	o32	clock_settime			sys_clock_settime32
+263	o32	clock_gettime			sys_clock_gettime32
+264	o32	clock_getres			sys_clock_getres_time32
+265	o32	clock_nanosleep			sys_clock_nanosleep_time32
+266	o32	tgkill				sys_tgkill
+267	o32	utimes				sys_utimes_time32
+268	o32	mbind				sys_mbind
+269	o32	get_mempolicy			sys_get_mempolicy
+270	o32	set_mempolicy			sys_set_mempolicy
+271	o32	mq_open				sys_mq_open			compat_sys_mq_open
+272	o32	mq_unlink			sys_mq_unlink
+273	o32	mq_timedsend			sys_mq_timedsend_time32
+274	o32	mq_timedreceive			sys_mq_timedreceive_time32
+275	o32	mq_notify			sys_mq_notify			compat_sys_mq_notify
+276	o32	mq_getsetattr			sys_mq_getsetattr		compat_sys_mq_getsetattr
+277	o32	vserver				sys_ni_syscall
+278	o32	waitid				sys_waitid			compat_sys_waitid
+# 279 was sys_setaltroot
+280	o32	add_key				sys_add_key
+281	o32	request_key			sys_request_key
+282	o32	keyctl				sys_keyctl			compat_sys_keyctl
+283	o32	set_thread_area			sys_set_thread_area
+284	o32	inotify_init			sys_inotify_init
+285	o32	inotify_add_watch		sys_inotify_add_watch
+286	o32	inotify_rm_watch		sys_inotify_rm_watch
+287	o32	migrate_pages			sys_migrate_pages
+288	o32	openat				sys_openat			compat_sys_openat
+289	o32	mkdirat				sys_mkdirat
+290	o32	mknodat				sys_mknodat
+291	o32	fchownat			sys_fchownat
+292	o32	futimesat			sys_futimesat_time32
+293	o32	fstatat64			sys_fstatat64			sys_newfstatat
+294	o32	unlinkat			sys_unlinkat
+295	o32	renameat			sys_renameat
+296	o32	linkat				sys_linkat
+297	o32	symlinkat			sys_symlinkat
+298	o32	readlinkat			sys_readlinkat
+299	o32	fchmodat			sys_fchmodat
+300	o32	faccessat			sys_faccessat
+301	o32	pselect6			sys_pselect6_time32		compat_sys_pselect6_time32
+302	o32	ppoll				sys_ppoll_time32		compat_sys_ppoll_time32
+303	o32	unshare				sys_unshare
+304	o32	splice				sys_splice
+305	o32	sync_file_range			sys_sync_file_range		sys32_sync_file_range
+306	o32	tee				sys_tee
+307	o32	vmsplice			sys_vmsplice
+308	o32	move_pages			sys_move_pages
+309	o32	set_robust_list			sys_set_robust_list		compat_sys_set_robust_list
+310	o32	get_robust_list			sys_get_robust_list		compat_sys_get_robust_list
+311	o32	kexec_load			sys_kexec_load			compat_sys_kexec_load
+312	o32	getcpu				sys_getcpu
+313	o32	epoll_pwait			sys_epoll_pwait			compat_sys_epoll_pwait
+314	o32	ioprio_set			sys_ioprio_set
+315	o32	ioprio_get			sys_ioprio_get
+316	o32	utimensat			sys_utimensat_time32
+317	o32	signalfd			sys_signalfd			compat_sys_signalfd
+318	o32	timerfd				sys_ni_syscall
+319	o32	eventfd				sys_eventfd
+320	o32	fallocate			sys_fallocate			sys32_fallocate
+321	o32	timerfd_create			sys_timerfd_create
+322	o32	timerfd_gettime			sys_timerfd_gettime32
+323	o32	timerfd_settime			sys_timerfd_settime32
+324	o32	signalfd4			sys_signalfd4			compat_sys_signalfd4
+325	o32	eventfd2			sys_eventfd2
+326	o32	epoll_create1			sys_epoll_create1
+327	o32	dup3				sys_dup3
+328	o32	pipe2				sys_pipe2
+329	o32	inotify_init1			sys_inotify_init1
+330	o32	preadv				sys_preadv			compat_sys_preadv
+331	o32	pwritev				sys_pwritev			compat_sys_pwritev
+332	o32	rt_tgsigqueueinfo		sys_rt_tgsigqueueinfo		compat_sys_rt_tgsigqueueinfo
+333	o32	perf_event_open			sys_perf_event_open
+334	o32	accept4				sys_accept4
+335	o32	recvmmsg			sys_recvmmsg_time32		compat_sys_recvmmsg_time32
+336	o32	fanotify_init			sys_fanotify_init
+337	o32	fanotify_mark			sys_fanotify_mark		compat_sys_fanotify_mark
+338	o32	prlimit64			sys_prlimit64
+339	o32	name_to_handle_at		sys_name_to_handle_at
+340	o32	open_by_handle_at		sys_open_by_handle_at		compat_sys_open_by_handle_at
+341	o32	clock_adjtime			sys_clock_adjtime32
+342	o32	syncfs				sys_syncfs
+343	o32	sendmmsg			sys_sendmmsg			compat_sys_sendmmsg
+344	o32	setns				sys_setns
+345	o32	process_vm_readv		sys_process_vm_readv
+346	o32	process_vm_writev		sys_process_vm_writev
+347	o32	kcmp				sys_kcmp
+348	o32	finit_module			sys_finit_module
+349	o32	sched_setattr			sys_sched_setattr
+350	o32	sched_getattr			sys_sched_getattr
+351	o32	renameat2			sys_renameat2
+352	o32	seccomp				sys_seccomp
+353	o32	getrandom			sys_getrandom
+354	o32	memfd_create			sys_memfd_create
+355	o32	bpf				sys_bpf
+356	o32	execveat			sys_execveat			compat_sys_execveat
+357	o32	userfaultfd			sys_userfaultfd
+358	o32	membarrier			sys_membarrier
+359	o32	mlock2				sys_mlock2
+360	o32	copy_file_range			sys_copy_file_range
+361	o32	preadv2				sys_preadv2			compat_sys_preadv2
+362	o32	pwritev2			sys_pwritev2			compat_sys_pwritev2
+363	o32	pkey_mprotect			sys_pkey_mprotect
+364	o32	pkey_alloc			sys_pkey_alloc
+365	o32	pkey_free			sys_pkey_free
+366	o32	statx				sys_statx
+367	o32	rseq				sys_rseq
+368	o32	io_pgetevents			sys_io_pgetevents_time32	compat_sys_io_pgetevents
+# room for arch specific calls
+393	o32	semget				sys_semget
+394	o32	semctl				sys_semctl			compat_sys_semctl
+395	o32	shmget				sys_shmget
+396	o32	shmctl				sys_shmctl			compat_sys_shmctl
+397	o32	shmat				sys_shmat			compat_sys_shmat
+398	o32	shmdt				sys_shmdt
+399	o32	msgget				sys_msgget
+400	o32	msgsnd				sys_msgsnd			compat_sys_msgsnd
+401	o32	msgrcv				sys_msgrcv			compat_sys_msgrcv
+402	o32	msgctl				sys_msgctl			compat_sys_msgctl
+403	o32	clock_gettime64			sys_clock_gettime		sys_clock_gettime
+404	o32	clock_settime64			sys_clock_settime		sys_clock_settime
+405	o32	clock_adjtime64			sys_clock_adjtime		sys_clock_adjtime
+406	o32	clock_getres_time64		sys_clock_getres		sys_clock_getres
+407	o32	clock_nanosleep_time64		sys_clock_nanosleep		sys_clock_nanosleep
+408	o32	timer_gettime64			sys_timer_gettime		sys_timer_gettime
+409	o32	timer_settime64			sys_timer_settime		sys_timer_settime
+410	o32	timerfd_gettime64		sys_timerfd_gettime		sys_timerfd_gettime
+411	o32	timerfd_settime64		sys_timerfd_settime		sys_timerfd_settime
+412	o32	utimensat_time64		sys_utimensat			sys_utimensat
+413	o32	pselect6_time64			sys_pselect6			compat_sys_pselect6_time64
+414	o32	ppoll_time64			sys_ppoll			compat_sys_ppoll_time64
+416	o32	io_pgetevents_time64		sys_io_pgetevents		sys_io_pgetevents
+417	o32	recvmmsg_time64			sys_recvmmsg			compat_sys_recvmmsg_time64
+418	o32	mq_timedsend_time64		sys_mq_timedsend		sys_mq_timedsend
+419	o32	mq_timedreceive_time64		sys_mq_timedreceive		sys_mq_timedreceive
+420	o32	semtimedop_time64		sys_semtimedop			sys_semtimedop
+421	o32	rt_sigtimedwait_time64		sys_rt_sigtimedwait		compat_sys_rt_sigtimedwait_time64
+422	o32	futex_time64			sys_futex			sys_futex
+423	o32	sched_rr_get_interval_time64	sys_sched_rr_get_interval	sys_sched_rr_get_interval
+424	o32	pidfd_send_signal		sys_pidfd_send_signal
+425	o32	io_uring_setup			sys_io_uring_setup
+426	o32	io_uring_enter			sys_io_uring_enter
+427	o32	io_uring_register		sys_io_uring_register
+428	o32	open_tree			sys_open_tree
+429	o32	move_mount			sys_move_mount
+430	o32	fsopen				sys_fsopen
+431	o32	fsconfig			sys_fsconfig
+432	o32	fsmount				sys_fsmount
+433	o32	fspick				sys_fspick
+434	o32	pidfd_open			sys_pidfd_open
+435	o32	clone3				__sys_clone3
+436	o32	close_range			sys_close_range
+437	o32	openat2				sys_openat2
+438	o32	pidfd_getfd			sys_pidfd_getfd
+439	o32	faccessat2			sys_faccessat2
+440	o32	process_madvise			sys_process_madvise
+441	o32	epoll_pwait2			sys_epoll_pwait2		compat_sys_epoll_pwait2
+442	o32	mount_setattr			sys_mount_setattr
+443	o32	quotactl_fd			sys_quotactl_fd
+444	o32	landlock_create_ruleset		sys_landlock_create_ruleset
+445	o32	landlock_add_rule		sys_landlock_add_rule
+446	o32	landlock_restrict_self		sys_landlock_restrict_self
+# 447 reserved for memfd_secret
+448	o32	process_mrelease		sys_process_mrelease
+449	o32	futex_waitv			sys_futex_waitv
+450	o32	set_mempolicy_home_node		sys_set_mempolicy_home_node
diff --git a/arch/mips/kernel/syscalls/syscallnr.sh b/arch/mips/kernel/syscalls/syscallnr.sh
new file mode 100644
index 000000000..c190bbefb
--- /dev/null
+++ b/arch/mips/kernel/syscalls/syscallnr.sh
@@ -0,0 +1,26 @@
+#!/bin/sh
+# SPDX-License-Identifier: GPL-2.0
+
+in="$1"
+out="$2"
+my_abis=`echo "($3)" | tr ',' '|'`
+prefix="$4"
+
+fileguard=_UAPI_ASM_MIPS_`basename "$out" | sed \
+	-e 'y/abcdefghijklmnopqrstuvwxyz/ABCDEFGHIJKLMNOPQRSTUVWXYZ/' \
+	-e 's/[^A-Z0-9_]/_/g' -e 's/__/_/g'`
+grep -E "^[0-9A-Fa-fXx]+[[:space:]]+${my_abis}" "$in" | sort -n | (
+	printf "#ifndef %s\n" "${fileguard}"
+	printf "#define %s\n" "${fileguard}"
+	printf "\n"
+
+	nxt=0
+	while read nr abi name entry compat ; do
+		nxt=$((nr+1))
+	done
+
+	printf "#define __NR_%s_Linux_syscalls\t%s\n" "${prefix}" "${nxt}"
+	printf "\n"
+	printf "#endif /* %s */" "${fileguard}"
+	printf "\n"
+) > "$out"
diff --git a/arch/mips/kernel/sysrq.c b/arch/mips/kernel/sysrq.c
new file mode 100644
index 000000000..9c1a20191
--- /dev/null
+++ b/arch/mips/kernel/sysrq.c
@@ -0,0 +1,66 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * MIPS specific sysrq operations.
+ *
+ * Copyright (C) 2015 Imagination Technologies Ltd.
+ */
+#include <linux/init.h>
+#include <linux/smp.h>
+#include <linux/spinlock.h>
+#include <linux/sysrq.h>
+#include <linux/workqueue.h>
+
+#include <asm/cpu-features.h>
+#include <asm/mipsregs.h>
+#include <asm/tlbdebug.h>
+
+/*
+ * Dump TLB entries on all CPUs.
+ */
+
+static DEFINE_SPINLOCK(show_lock);
+
+static void sysrq_tlbdump_single(void *dummy)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&show_lock, flags);
+
+	pr_info("CPU%d:\n", smp_processor_id());
+	dump_tlb_regs();
+	pr_info("\n");
+	dump_tlb_all();
+	pr_info("\n");
+
+	spin_unlock_irqrestore(&show_lock, flags);
+}
+
+#ifdef CONFIG_SMP
+static void sysrq_tlbdump_othercpus(struct work_struct *dummy)
+{
+	smp_call_function(sysrq_tlbdump_single, NULL, 0);
+}
+
+static DECLARE_WORK(sysrq_tlbdump, sysrq_tlbdump_othercpus);
+#endif
+
+static void sysrq_handle_tlbdump(int key)
+{
+	sysrq_tlbdump_single(NULL);
+#ifdef CONFIG_SMP
+	schedule_work(&sysrq_tlbdump);
+#endif
+}
+
+static const struct sysrq_key_op sysrq_tlbdump_op = {
+	.handler        = sysrq_handle_tlbdump,
+	.help_msg       = "show-tlbs(x)",
+	.action_msg     = "Show TLB entries",
+	.enable_mask	= SYSRQ_ENABLE_DUMP,
+};
+
+static int __init mips_sysrq_init(void)
+{
+	return register_sysrq_key('x', &sysrq_tlbdump_op);
+}
+arch_initcall(mips_sysrq_init);
diff --git a/arch/mips/kernel/time.c b/arch/mips/kernel/time.c
new file mode 100644
index 000000000..ed339d797
--- /dev/null
+++ b/arch/mips/kernel/time.c
@@ -0,0 +1,167 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2001 MontaVista Software Inc.
+ * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net
+ * Copyright (c) 2003, 2004  Maciej W. Rozycki
+ *
+ * Common time service routines for MIPS machines.
+ */
+#include <linux/bug.h>
+#include <linux/clockchips.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/sched.h>
+#include <linux/param.h>
+#include <linux/time.h>
+#include <linux/timex.h>
+#include <linux/smp.h>
+#include <linux/spinlock.h>
+#include <linux/export.h>
+#include <linux/cpufreq.h>
+#include <linux/delay.h>
+
+#include <asm/cpu-features.h>
+#include <asm/cpu-type.h>
+#include <asm/div64.h>
+#include <asm/time.h>
+
+#ifdef CONFIG_CPU_FREQ
+
+static DEFINE_PER_CPU(unsigned long, pcp_lpj_ref);
+static DEFINE_PER_CPU(unsigned long, pcp_lpj_ref_freq);
+static unsigned long glb_lpj_ref;
+static unsigned long glb_lpj_ref_freq;
+
+static int cpufreq_callback(struct notifier_block *nb,
+			    unsigned long val, void *data)
+{
+	struct cpufreq_freqs *freq = data;
+	struct cpumask *cpus = freq->policy->cpus;
+	unsigned long lpj;
+	int cpu;
+
+	/*
+	 * Skip lpj numbers adjustment if the CPU-freq transition is safe for
+	 * the loops delay. (Is this possible?)
+	 */
+	if (freq->flags & CPUFREQ_CONST_LOOPS)
+		return NOTIFY_OK;
+
+	/* Save the initial values of the lpjes for future scaling. */
+	if (!glb_lpj_ref) {
+		glb_lpj_ref = boot_cpu_data.udelay_val;
+		glb_lpj_ref_freq = freq->old;
+
+		for_each_online_cpu(cpu) {
+			per_cpu(pcp_lpj_ref, cpu) =
+				cpu_data[cpu].udelay_val;
+			per_cpu(pcp_lpj_ref_freq, cpu) = freq->old;
+		}
+	}
+
+	/*
+	 * Adjust global lpj variable and per-CPU udelay_val number in
+	 * accordance with the new CPU frequency.
+	 */
+	if ((val == CPUFREQ_PRECHANGE  && freq->old < freq->new) ||
+	    (val == CPUFREQ_POSTCHANGE && freq->old > freq->new)) {
+		loops_per_jiffy = cpufreq_scale(glb_lpj_ref,
+						glb_lpj_ref_freq,
+						freq->new);
+
+		for_each_cpu(cpu, cpus) {
+			lpj = cpufreq_scale(per_cpu(pcp_lpj_ref, cpu),
+					    per_cpu(pcp_lpj_ref_freq, cpu),
+					    freq->new);
+			cpu_data[cpu].udelay_val = (unsigned int)lpj;
+		}
+	}
+
+	return NOTIFY_OK;
+}
+
+static struct notifier_block cpufreq_notifier = {
+	.notifier_call  = cpufreq_callback,
+};
+
+static int __init register_cpufreq_notifier(void)
+{
+	return cpufreq_register_notifier(&cpufreq_notifier,
+					 CPUFREQ_TRANSITION_NOTIFIER);
+}
+core_initcall(register_cpufreq_notifier);
+
+#endif /* CONFIG_CPU_FREQ */
+
+/*
+ * forward reference
+ */
+DEFINE_SPINLOCK(rtc_lock);
+EXPORT_SYMBOL(rtc_lock);
+
+static int null_perf_irq(void)
+{
+	return 0;
+}
+
+int (*perf_irq)(void) = null_perf_irq;
+
+EXPORT_SYMBOL(perf_irq);
+
+/*
+ * time_init() - it does the following things.
+ *
+ * 1) plat_time_init() -
+ *	a) (optional) set up RTC routines,
+ *	b) (optional) calibrate and set the mips_hpt_frequency
+ *	    (only needed if you intended to use cpu counter as timer interrupt
+ *	     source)
+ * 2) calculate a couple of cached variables for later usage
+ */
+
+unsigned int mips_hpt_frequency;
+EXPORT_SYMBOL_GPL(mips_hpt_frequency);
+
+static __init int cpu_has_mfc0_count_bug(void)
+{
+	switch (current_cpu_type()) {
+	case CPU_R4000PC:
+	case CPU_R4000SC:
+	case CPU_R4000MC:
+		/*
+		 * V3.0 is documented as suffering from the mfc0 from count bug.
+		 * Afaik this is the last version of the R4000.	 Later versions
+		 * were marketed as R4400.
+		 */
+		return 1;
+
+	case CPU_R4400PC:
+	case CPU_R4400SC:
+	case CPU_R4400MC:
+		/*
+		 * The published errata for the R4400 up to 3.0 say the CPU
+		 * has the mfc0 from count bug.  This seems the last version
+		 * produced.
+		 */
+		return 1;
+	}
+
+	return 0;
+}
+
+void __init time_init(void)
+{
+	plat_time_init();
+
+	/*
+	 * The use of the R4k timer as a clock event takes precedence;
+	 * if reading the Count register might interfere with the timer
+	 * interrupt, then we don't use the timer as a clock source.
+	 * We may still use the timer as a clock source though if the
+	 * timer interrupt isn't reliable; the interference doesn't
+	 * matter then, because we don't use the interrupt.
+	 */
+	if (mips_clockevent_init() != 0 || !cpu_has_mfc0_count_bug())
+		init_mips_clocksource();
+}
diff --git a/arch/mips/kernel/topology.c b/arch/mips/kernel/topology.c
new file mode 100644
index 000000000..9429d85a4
--- /dev/null
+++ b/arch/mips/kernel/topology.c
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/cpu.h>
+#include <linux/cpumask.h>
+#include <linux/init.h>
+#include <linux/node.h>
+#include <linux/nodemask.h>
+#include <linux/percpu.h>
+
+static DEFINE_PER_CPU(struct cpu, cpu_devices);
+
+static int __init topology_init(void)
+{
+	int i, ret;
+
+	for_each_present_cpu(i) {
+		struct cpu *c = &per_cpu(cpu_devices, i);
+
+		c->hotpluggable = !!i;
+		ret = register_cpu(c, i);
+		if (ret)
+			printk(KERN_WARNING "topology_init: register_cpu %d "
+			       "failed (%d)\n", i, ret);
+	}
+
+	return 0;
+}
+
+subsys_initcall(topology_init);
diff --git a/arch/mips/kernel/traps.c b/arch/mips/kernel/traps.c
new file mode 100644
index 000000000..246c6a6b0
--- /dev/null
+++ b/arch/mips/kernel/traps.c
@@ -0,0 +1,2562 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994 - 1999, 2000, 01, 06 Ralf Baechle
+ * Copyright (C) 1995, 1996 Paul M. Antoine
+ * Copyright (C) 1998 Ulf Carlsson
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ * Kevin D. Kissell, kevink@mips.com and Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 2002, 2003, 2004, 2005, 2007  Maciej W. Rozycki
+ * Copyright (C) 2000, 2001, 2012 MIPS Technologies, Inc.  All rights reserved.
+ * Copyright (C) 2014, Imagination Technologies Ltd.
+ */
+#include <linux/bitops.h>
+#include <linux/bug.h>
+#include <linux/compiler.h>
+#include <linux/context_tracking.h>
+#include <linux/cpu_pm.h>
+#include <linux/kexec.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/extable.h>
+#include <linux/mm.h>
+#include <linux/sched/mm.h>
+#include <linux/sched/debug.h>
+#include <linux/smp.h>
+#include <linux/spinlock.h>
+#include <linux/kallsyms.h>
+#include <linux/memblock.h>
+#include <linux/interrupt.h>
+#include <linux/ptrace.h>
+#include <linux/kgdb.h>
+#include <linux/kdebug.h>
+#include <linux/kprobes.h>
+#include <linux/notifier.h>
+#include <linux/kdb.h>
+#include <linux/irq.h>
+#include <linux/perf_event.h>
+
+#include <asm/addrspace.h>
+#include <asm/bootinfo.h>
+#include <asm/branch.h>
+#include <asm/break.h>
+#include <asm/cop2.h>
+#include <asm/cpu.h>
+#include <asm/cpu-type.h>
+#include <asm/dsp.h>
+#include <asm/fpu.h>
+#include <asm/fpu_emulator.h>
+#include <asm/idle.h>
+#include <asm/isa-rev.h>
+#include <asm/mips-cps.h>
+#include <asm/mips-r2-to-r6-emul.h>
+#include <asm/mipsregs.h>
+#include <asm/mipsmtregs.h>
+#include <asm/module.h>
+#include <asm/msa.h>
+#include <asm/ptrace.h>
+#include <asm/sections.h>
+#include <asm/siginfo.h>
+#include <asm/tlbdebug.h>
+#include <asm/traps.h>
+#include <linux/uaccess.h>
+#include <asm/watch.h>
+#include <asm/mmu_context.h>
+#include <asm/types.h>
+#include <asm/stacktrace.h>
+#include <asm/tlbex.h>
+#include <asm/uasm.h>
+
+#include <asm/mach-loongson64/cpucfg-emul.h>
+
+#include "access-helper.h"
+
+extern void check_wait(void);
+extern asmlinkage void rollback_handle_int(void);
+extern asmlinkage void handle_int(void);
+extern asmlinkage void handle_adel(void);
+extern asmlinkage void handle_ades(void);
+extern asmlinkage void handle_ibe(void);
+extern asmlinkage void handle_dbe(void);
+extern asmlinkage void handle_sys(void);
+extern asmlinkage void handle_bp(void);
+extern asmlinkage void handle_ri(void);
+extern asmlinkage void handle_ri_rdhwr_tlbp(void);
+extern asmlinkage void handle_ri_rdhwr(void);
+extern asmlinkage void handle_cpu(void);
+extern asmlinkage void handle_ov(void);
+extern asmlinkage void handle_tr(void);
+extern asmlinkage void handle_msa_fpe(void);
+extern asmlinkage void handle_fpe(void);
+extern asmlinkage void handle_ftlb(void);
+extern asmlinkage void handle_gsexc(void);
+extern asmlinkage void handle_msa(void);
+extern asmlinkage void handle_mdmx(void);
+extern asmlinkage void handle_watch(void);
+extern asmlinkage void handle_mt(void);
+extern asmlinkage void handle_dsp(void);
+extern asmlinkage void handle_mcheck(void);
+extern asmlinkage void handle_reserved(void);
+extern void tlb_do_page_fault_0(void);
+
+void (*board_be_init)(void);
+static int (*board_be_handler)(struct pt_regs *regs, int is_fixup);
+void (*board_nmi_handler_setup)(void);
+void (*board_ejtag_handler_setup)(void);
+void (*board_bind_eic_interrupt)(int irq, int regset);
+void (*board_ebase_setup)(void);
+void(*board_cache_error_setup)(void);
+
+void mips_set_be_handler(int (*handler)(struct pt_regs *regs, int is_fixup))
+{
+	board_be_handler = handler;
+}
+EXPORT_SYMBOL_GPL(mips_set_be_handler);
+
+static void show_raw_backtrace(unsigned long reg29, const char *loglvl,
+			       bool user)
+{
+	unsigned long *sp = (unsigned long *)(reg29 & ~3);
+	unsigned long addr;
+
+	printk("%sCall Trace:", loglvl);
+#ifdef CONFIG_KALLSYMS
+	printk("%s\n", loglvl);
+#endif
+	while (!kstack_end(sp)) {
+		if (__get_addr(&addr, sp++, user)) {
+			printk("%s (Bad stack address)", loglvl);
+			break;
+		}
+		if (__kernel_text_address(addr))
+			print_ip_sym(loglvl, addr);
+	}
+	printk("%s\n", loglvl);
+}
+
+#ifdef CONFIG_KALLSYMS
+int raw_show_trace;
+static int __init set_raw_show_trace(char *str)
+{
+	raw_show_trace = 1;
+	return 1;
+}
+__setup("raw_show_trace", set_raw_show_trace);
+#endif
+
+static void show_backtrace(struct task_struct *task, const struct pt_regs *regs,
+			   const char *loglvl, bool user)
+{
+	unsigned long sp = regs->regs[29];
+	unsigned long ra = regs->regs[31];
+	unsigned long pc = regs->cp0_epc;
+
+	if (!task)
+		task = current;
+
+	if (raw_show_trace || user_mode(regs) || !__kernel_text_address(pc)) {
+		show_raw_backtrace(sp, loglvl, user);
+		return;
+	}
+	printk("%sCall Trace:\n", loglvl);
+	do {
+		print_ip_sym(loglvl, pc);
+		pc = unwind_stack(task, &sp, pc, &ra);
+	} while (pc);
+	pr_cont("\n");
+}
+
+/*
+ * This routine abuses get_user()/put_user() to reference pointers
+ * with at least a bit of error checking ...
+ */
+static void show_stacktrace(struct task_struct *task,
+	const struct pt_regs *regs, const char *loglvl, bool user)
+{
+	const int field = 2 * sizeof(unsigned long);
+	unsigned long stackdata;
+	int i;
+	unsigned long *sp = (unsigned long *)regs->regs[29];
+
+	printk("%sStack :", loglvl);
+	i = 0;
+	while ((unsigned long) sp & (PAGE_SIZE - 1)) {
+		if (i && ((i % (64 / field)) == 0)) {
+			pr_cont("\n");
+			printk("%s       ", loglvl);
+		}
+		if (i > 39) {
+			pr_cont(" ...");
+			break;
+		}
+
+		if (__get_addr(&stackdata, sp++, user)) {
+			pr_cont(" (Bad stack address)");
+			break;
+		}
+
+		pr_cont(" %0*lx", field, stackdata);
+		i++;
+	}
+	pr_cont("\n");
+	show_backtrace(task, regs, loglvl, user);
+}
+
+void show_stack(struct task_struct *task, unsigned long *sp, const char *loglvl)
+{
+	struct pt_regs regs;
+
+	regs.cp0_status = KSU_KERNEL;
+	if (sp) {
+		regs.regs[29] = (unsigned long)sp;
+		regs.regs[31] = 0;
+		regs.cp0_epc = 0;
+	} else {
+		if (task && task != current) {
+			regs.regs[29] = task->thread.reg29;
+			regs.regs[31] = 0;
+			regs.cp0_epc = task->thread.reg31;
+		} else {
+			prepare_frametrace(&regs);
+		}
+	}
+	show_stacktrace(task, &regs, loglvl, false);
+}
+
+static void show_code(void *pc, bool user)
+{
+	long i;
+	unsigned short *pc16 = NULL;
+
+	printk("Code:");
+
+	if ((unsigned long)pc & 1)
+		pc16 = (u16 *)((unsigned long)pc & ~1);
+
+	for(i = -3 ; i < 6 ; i++) {
+		if (pc16) {
+			u16 insn16;
+
+			if (__get_inst16(&insn16, pc16 + i, user))
+				goto bad_address;
+
+			pr_cont("%c%04x%c", (i?' ':'<'), insn16, (i?' ':'>'));
+		} else {
+			u32 insn32;
+
+			if (__get_inst32(&insn32, (u32 *)pc + i, user))
+				goto bad_address;
+
+			pr_cont("%c%08x%c", (i?' ':'<'), insn32, (i?' ':'>'));
+		}
+	}
+	pr_cont("\n");
+	return;
+
+bad_address:
+	pr_cont(" (Bad address in epc)\n\n");
+}
+
+static void __show_regs(const struct pt_regs *regs)
+{
+	const int field = 2 * sizeof(unsigned long);
+	unsigned int cause = regs->cp0_cause;
+	unsigned int exccode;
+	int i;
+
+	show_regs_print_info(KERN_DEFAULT);
+
+	/*
+	 * Saved main processor registers
+	 */
+	for (i = 0; i < 32; ) {
+		if ((i % 4) == 0)
+			printk("$%2d   :", i);
+		if (i == 0)
+			pr_cont(" %0*lx", field, 0UL);
+		else if (i == 26 || i == 27)
+			pr_cont(" %*s", field, "");
+		else
+			pr_cont(" %0*lx", field, regs->regs[i]);
+
+		i++;
+		if ((i % 4) == 0)
+			pr_cont("\n");
+	}
+
+#ifdef CONFIG_CPU_HAS_SMARTMIPS
+	printk("Acx    : %0*lx\n", field, regs->acx);
+#endif
+	if (MIPS_ISA_REV < 6) {
+		printk("Hi    : %0*lx\n", field, regs->hi);
+		printk("Lo    : %0*lx\n", field, regs->lo);
+	}
+
+	/*
+	 * Saved cp0 registers
+	 */
+	printk("epc   : %0*lx %pS\n", field, regs->cp0_epc,
+	       (void *) regs->cp0_epc);
+	printk("ra    : %0*lx %pS\n", field, regs->regs[31],
+	       (void *) regs->regs[31]);
+
+	printk("Status: %08x	", (uint32_t) regs->cp0_status);
+
+	if (cpu_has_3kex) {
+		if (regs->cp0_status & ST0_KUO)
+			pr_cont("KUo ");
+		if (regs->cp0_status & ST0_IEO)
+			pr_cont("IEo ");
+		if (regs->cp0_status & ST0_KUP)
+			pr_cont("KUp ");
+		if (regs->cp0_status & ST0_IEP)
+			pr_cont("IEp ");
+		if (regs->cp0_status & ST0_KUC)
+			pr_cont("KUc ");
+		if (regs->cp0_status & ST0_IEC)
+			pr_cont("IEc ");
+	} else if (cpu_has_4kex) {
+		if (regs->cp0_status & ST0_KX)
+			pr_cont("KX ");
+		if (regs->cp0_status & ST0_SX)
+			pr_cont("SX ");
+		if (regs->cp0_status & ST0_UX)
+			pr_cont("UX ");
+		switch (regs->cp0_status & ST0_KSU) {
+		case KSU_USER:
+			pr_cont("USER ");
+			break;
+		case KSU_SUPERVISOR:
+			pr_cont("SUPERVISOR ");
+			break;
+		case KSU_KERNEL:
+			pr_cont("KERNEL ");
+			break;
+		default:
+			pr_cont("BAD_MODE ");
+			break;
+		}
+		if (regs->cp0_status & ST0_ERL)
+			pr_cont("ERL ");
+		if (regs->cp0_status & ST0_EXL)
+			pr_cont("EXL ");
+		if (regs->cp0_status & ST0_IE)
+			pr_cont("IE ");
+	}
+	pr_cont("\n");
+
+	exccode = (cause & CAUSEF_EXCCODE) >> CAUSEB_EXCCODE;
+	printk("Cause : %08x (ExcCode %02x)\n", cause, exccode);
+
+	if (1 <= exccode && exccode <= 5)
+		printk("BadVA : %0*lx\n", field, regs->cp0_badvaddr);
+
+	printk("PrId  : %08x (%s)\n", read_c0_prid(),
+	       cpu_name_string());
+}
+
+/*
+ * FIXME: really the generic show_regs should take a const pointer argument.
+ */
+void show_regs(struct pt_regs *regs)
+{
+	__show_regs(regs);
+	dump_stack();
+}
+
+void show_registers(struct pt_regs *regs)
+{
+	const int field = 2 * sizeof(unsigned long);
+
+	__show_regs(regs);
+	print_modules();
+	printk("Process %s (pid: %d, threadinfo=%p, task=%p, tls=%0*lx)\n",
+	       current->comm, current->pid, current_thread_info(), current,
+	      field, current_thread_info()->tp_value);
+	if (cpu_has_userlocal) {
+		unsigned long tls;
+
+		tls = read_c0_userlocal();
+		if (tls != current_thread_info()->tp_value)
+			printk("*HwTLS: %0*lx\n", field, tls);
+	}
+
+	show_stacktrace(current, regs, KERN_DEFAULT, user_mode(regs));
+	show_code((void *)regs->cp0_epc, user_mode(regs));
+	printk("\n");
+}
+
+static DEFINE_RAW_SPINLOCK(die_lock);
+
+void __noreturn die(const char *str, struct pt_regs *regs)
+{
+	static int die_counter;
+	int sig = SIGSEGV;
+
+	oops_enter();
+
+	if (notify_die(DIE_OOPS, str, regs, 0, current->thread.trap_nr,
+		       SIGSEGV) == NOTIFY_STOP)
+		sig = 0;
+
+	console_verbose();
+	raw_spin_lock_irq(&die_lock);
+	bust_spinlocks(1);
+
+	printk("%s[#%d]:\n", str, ++die_counter);
+	show_registers(regs);
+	add_taint(TAINT_DIE, LOCKDEP_NOW_UNRELIABLE);
+	raw_spin_unlock_irq(&die_lock);
+
+	oops_exit();
+
+	if (in_interrupt())
+		panic("Fatal exception in interrupt");
+
+	if (panic_on_oops)
+		panic("Fatal exception");
+
+	if (regs && kexec_should_crash(current))
+		crash_kexec(regs);
+
+	make_task_dead(sig);
+}
+
+extern struct exception_table_entry __start___dbe_table[];
+extern struct exception_table_entry __stop___dbe_table[];
+
+__asm__(
+"	.section	__dbe_table, \"a\"\n"
+"	.previous			\n");
+
+/* Given an address, look for it in the exception tables. */
+static const struct exception_table_entry *search_dbe_tables(unsigned long addr)
+{
+	const struct exception_table_entry *e;
+
+	e = search_extable(__start___dbe_table,
+			   __stop___dbe_table - __start___dbe_table, addr);
+	if (!e)
+		e = search_module_dbetables(addr);
+	return e;
+}
+
+asmlinkage void do_be(struct pt_regs *regs)
+{
+	const int field = 2 * sizeof(unsigned long);
+	const struct exception_table_entry *fixup = NULL;
+	int data = regs->cp0_cause & 4;
+	int action = MIPS_BE_FATAL;
+	enum ctx_state prev_state;
+
+	prev_state = exception_enter();
+	/* XXX For now.	 Fixme, this searches the wrong table ...  */
+	if (data && !user_mode(regs))
+		fixup = search_dbe_tables(exception_epc(regs));
+
+	if (fixup)
+		action = MIPS_BE_FIXUP;
+
+	if (board_be_handler)
+		action = board_be_handler(regs, fixup != NULL);
+	else
+		mips_cm_error_report();
+
+	switch (action) {
+	case MIPS_BE_DISCARD:
+		goto out;
+	case MIPS_BE_FIXUP:
+		if (fixup) {
+			regs->cp0_epc = fixup->nextinsn;
+			goto out;
+		}
+		break;
+	default:
+		break;
+	}
+
+	/*
+	 * Assume it would be too dangerous to continue ...
+	 */
+	printk(KERN_ALERT "%s bus error, epc == %0*lx, ra == %0*lx\n",
+	       data ? "Data" : "Instruction",
+	       field, regs->cp0_epc, field, regs->regs[31]);
+	if (notify_die(DIE_OOPS, "bus error", regs, 0, current->thread.trap_nr,
+		       SIGBUS) == NOTIFY_STOP)
+		goto out;
+
+	die_if_kernel("Oops", regs);
+	force_sig(SIGBUS);
+
+out:
+	exception_exit(prev_state);
+}
+
+/*
+ * ll/sc, rdhwr, sync emulation
+ */
+
+#define OPCODE 0xfc000000
+#define BASE   0x03e00000
+#define RT     0x001f0000
+#define OFFSET 0x0000ffff
+#define LL     0xc0000000
+#define SC     0xe0000000
+#define SPEC0  0x00000000
+#define SPEC3  0x7c000000
+#define RD     0x0000f800
+#define FUNC   0x0000003f
+#define SYNC   0x0000000f
+#define RDHWR  0x0000003b
+
+/*  microMIPS definitions   */
+#define MM_POOL32A_FUNC 0xfc00ffff
+#define MM_RDHWR        0x00006b3c
+#define MM_RS           0x001f0000
+#define MM_RT           0x03e00000
+
+/*
+ * The ll_bit is cleared by r*_switch.S
+ */
+
+unsigned int ll_bit;
+struct task_struct *ll_task;
+
+static inline int simulate_ll(struct pt_regs *regs, unsigned int opcode)
+{
+	unsigned long value, __user *vaddr;
+	long offset;
+
+	/*
+	 * analyse the ll instruction that just caused a ri exception
+	 * and put the referenced address to addr.
+	 */
+
+	/* sign extend offset */
+	offset = opcode & OFFSET;
+	offset <<= 16;
+	offset >>= 16;
+
+	vaddr = (unsigned long __user *)
+		((unsigned long)(regs->regs[(opcode & BASE) >> 21]) + offset);
+
+	if ((unsigned long)vaddr & 3)
+		return SIGBUS;
+	if (get_user(value, vaddr))
+		return SIGSEGV;
+
+	preempt_disable();
+
+	if (ll_task == NULL || ll_task == current) {
+		ll_bit = 1;
+	} else {
+		ll_bit = 0;
+	}
+	ll_task = current;
+
+	preempt_enable();
+
+	regs->regs[(opcode & RT) >> 16] = value;
+
+	return 0;
+}
+
+static inline int simulate_sc(struct pt_regs *regs, unsigned int opcode)
+{
+	unsigned long __user *vaddr;
+	unsigned long reg;
+	long offset;
+
+	/*
+	 * analyse the sc instruction that just caused a ri exception
+	 * and put the referenced address to addr.
+	 */
+
+	/* sign extend offset */
+	offset = opcode & OFFSET;
+	offset <<= 16;
+	offset >>= 16;
+
+	vaddr = (unsigned long __user *)
+		((unsigned long)(regs->regs[(opcode & BASE) >> 21]) + offset);
+	reg = (opcode & RT) >> 16;
+
+	if ((unsigned long)vaddr & 3)
+		return SIGBUS;
+
+	preempt_disable();
+
+	if (ll_bit == 0 || ll_task != current) {
+		regs->regs[reg] = 0;
+		preempt_enable();
+		return 0;
+	}
+
+	preempt_enable();
+
+	if (put_user(regs->regs[reg], vaddr))
+		return SIGSEGV;
+
+	regs->regs[reg] = 1;
+
+	return 0;
+}
+
+/*
+ * ll uses the opcode of lwc0 and sc uses the opcode of swc0.  That is both
+ * opcodes are supposed to result in coprocessor unusable exceptions if
+ * executed on ll/sc-less processors.  That's the theory.  In practice a
+ * few processors such as NEC's VR4100 throw reserved instruction exceptions
+ * instead, so we're doing the emulation thing in both exception handlers.
+ */
+static int simulate_llsc(struct pt_regs *regs, unsigned int opcode)
+{
+	if ((opcode & OPCODE) == LL) {
+		perf_sw_event(PERF_COUNT_SW_EMULATION_FAULTS,
+				1, regs, 0);
+		return simulate_ll(regs, opcode);
+	}
+	if ((opcode & OPCODE) == SC) {
+		perf_sw_event(PERF_COUNT_SW_EMULATION_FAULTS,
+				1, regs, 0);
+		return simulate_sc(regs, opcode);
+	}
+
+	return -1;			/* Must be something else ... */
+}
+
+/*
+ * Simulate trapping 'rdhwr' instructions to provide user accessible
+ * registers not implemented in hardware.
+ */
+static int simulate_rdhwr(struct pt_regs *regs, int rd, int rt)
+{
+	struct thread_info *ti = task_thread_info(current);
+
+	perf_sw_event(PERF_COUNT_SW_EMULATION_FAULTS,
+			1, regs, 0);
+	switch (rd) {
+	case MIPS_HWR_CPUNUM:		/* CPU number */
+		regs->regs[rt] = smp_processor_id();
+		return 0;
+	case MIPS_HWR_SYNCISTEP:	/* SYNCI length */
+		regs->regs[rt] = min(current_cpu_data.dcache.linesz,
+				     current_cpu_data.icache.linesz);
+		return 0;
+	case MIPS_HWR_CC:		/* Read count register */
+		regs->regs[rt] = read_c0_count();
+		return 0;
+	case MIPS_HWR_CCRES:		/* Count register resolution */
+		switch (current_cpu_type()) {
+		case CPU_20KC:
+		case CPU_25KF:
+			regs->regs[rt] = 1;
+			break;
+		default:
+			regs->regs[rt] = 2;
+		}
+		return 0;
+	case MIPS_HWR_ULR:		/* Read UserLocal register */
+		regs->regs[rt] = ti->tp_value;
+		return 0;
+	default:
+		return -1;
+	}
+}
+
+static int simulate_rdhwr_normal(struct pt_regs *regs, unsigned int opcode)
+{
+	if ((opcode & OPCODE) == SPEC3 && (opcode & FUNC) == RDHWR) {
+		int rd = (opcode & RD) >> 11;
+		int rt = (opcode & RT) >> 16;
+
+		simulate_rdhwr(regs, rd, rt);
+		return 0;
+	}
+
+	/* Not ours.  */
+	return -1;
+}
+
+static int simulate_rdhwr_mm(struct pt_regs *regs, unsigned int opcode)
+{
+	if ((opcode & MM_POOL32A_FUNC) == MM_RDHWR) {
+		int rd = (opcode & MM_RS) >> 16;
+		int rt = (opcode & MM_RT) >> 21;
+		simulate_rdhwr(regs, rd, rt);
+		return 0;
+	}
+
+	/* Not ours.  */
+	return -1;
+}
+
+static int simulate_sync(struct pt_regs *regs, unsigned int opcode)
+{
+	if ((opcode & OPCODE) == SPEC0 && (opcode & FUNC) == SYNC) {
+		perf_sw_event(PERF_COUNT_SW_EMULATION_FAULTS,
+				1, regs, 0);
+		return 0;
+	}
+
+	return -1;			/* Must be something else ... */
+}
+
+/*
+ * Loongson-3 CSR instructions emulation
+ */
+
+#ifdef CONFIG_CPU_LOONGSON3_CPUCFG_EMULATION
+
+#define LWC2             0xc8000000
+#define RS               BASE
+#define CSR_OPCODE2      0x00000118
+#define CSR_OPCODE2_MASK 0x000007ff
+#define CSR_FUNC_MASK    RT
+#define CSR_FUNC_CPUCFG  0x8
+
+static int simulate_loongson3_cpucfg(struct pt_regs *regs,
+				     unsigned int opcode)
+{
+	int op = opcode & OPCODE;
+	int op2 = opcode & CSR_OPCODE2_MASK;
+	int csr_func = (opcode & CSR_FUNC_MASK) >> 16;
+
+	if (op == LWC2 && op2 == CSR_OPCODE2 && csr_func == CSR_FUNC_CPUCFG) {
+		int rd = (opcode & RD) >> 11;
+		int rs = (opcode & RS) >> 21;
+		__u64 sel = regs->regs[rs];
+
+		perf_sw_event(PERF_COUNT_SW_EMULATION_FAULTS, 1, regs, 0);
+
+		/* Do not emulate on unsupported core models. */
+		preempt_disable();
+		if (!loongson3_cpucfg_emulation_enabled(&current_cpu_data)) {
+			preempt_enable();
+			return -1;
+		}
+		regs->regs[rd] = loongson3_cpucfg_read_synthesized(
+			&current_cpu_data, sel);
+		preempt_enable();
+		return 0;
+	}
+
+	/* Not ours.  */
+	return -1;
+}
+#endif /* CONFIG_CPU_LOONGSON3_CPUCFG_EMULATION */
+
+asmlinkage void do_ov(struct pt_regs *regs)
+{
+	enum ctx_state prev_state;
+
+	prev_state = exception_enter();
+	die_if_kernel("Integer overflow", regs);
+
+	force_sig_fault(SIGFPE, FPE_INTOVF, (void __user *)regs->cp0_epc);
+	exception_exit(prev_state);
+}
+
+#ifdef CONFIG_MIPS_FP_SUPPORT
+
+/*
+ * Send SIGFPE according to FCSR Cause bits, which must have already
+ * been masked against Enable bits.  This is impotant as Inexact can
+ * happen together with Overflow or Underflow, and `ptrace' can set
+ * any bits.
+ */
+void force_fcr31_sig(unsigned long fcr31, void __user *fault_addr,
+		     struct task_struct *tsk)
+{
+	int si_code = FPE_FLTUNK;
+
+	if (fcr31 & FPU_CSR_INV_X)
+		si_code = FPE_FLTINV;
+	else if (fcr31 & FPU_CSR_DIV_X)
+		si_code = FPE_FLTDIV;
+	else if (fcr31 & FPU_CSR_OVF_X)
+		si_code = FPE_FLTOVF;
+	else if (fcr31 & FPU_CSR_UDF_X)
+		si_code = FPE_FLTUND;
+	else if (fcr31 & FPU_CSR_INE_X)
+		si_code = FPE_FLTRES;
+
+	force_sig_fault_to_task(SIGFPE, si_code, fault_addr, tsk);
+}
+
+int process_fpemu_return(int sig, void __user *fault_addr, unsigned long fcr31)
+{
+	int si_code;
+
+	switch (sig) {
+	case 0:
+		return 0;
+
+	case SIGFPE:
+		force_fcr31_sig(fcr31, fault_addr, current);
+		return 1;
+
+	case SIGBUS:
+		force_sig_fault(SIGBUS, BUS_ADRERR, fault_addr);
+		return 1;
+
+	case SIGSEGV:
+		mmap_read_lock(current->mm);
+		if (vma_lookup(current->mm, (unsigned long)fault_addr))
+			si_code = SEGV_ACCERR;
+		else
+			si_code = SEGV_MAPERR;
+		mmap_read_unlock(current->mm);
+		force_sig_fault(SIGSEGV, si_code, fault_addr);
+		return 1;
+
+	default:
+		force_sig(sig);
+		return 1;
+	}
+}
+
+static int simulate_fp(struct pt_regs *regs, unsigned int opcode,
+		       unsigned long old_epc, unsigned long old_ra)
+{
+	union mips_instruction inst = { .word = opcode };
+	void __user *fault_addr;
+	unsigned long fcr31;
+	int sig;
+
+	/* If it's obviously not an FP instruction, skip it */
+	switch (inst.i_format.opcode) {
+	case cop1_op:
+	case cop1x_op:
+	case lwc1_op:
+	case ldc1_op:
+	case swc1_op:
+	case sdc1_op:
+		break;
+
+	default:
+		return -1;
+	}
+
+	/*
+	 * do_ri skipped over the instruction via compute_return_epc, undo
+	 * that for the FPU emulator.
+	 */
+	regs->cp0_epc = old_epc;
+	regs->regs[31] = old_ra;
+
+	/* Run the emulator */
+	sig = fpu_emulator_cop1Handler(regs, &current->thread.fpu, 1,
+				       &fault_addr);
+
+	/*
+	 * We can't allow the emulated instruction to leave any
+	 * enabled Cause bits set in $fcr31.
+	 */
+	fcr31 = mask_fcr31_x(current->thread.fpu.fcr31);
+	current->thread.fpu.fcr31 &= ~fcr31;
+
+	/* Restore the hardware register state */
+	own_fpu(1);
+
+	/* Send a signal if required.  */
+	process_fpemu_return(sig, fault_addr, fcr31);
+
+	return 0;
+}
+
+/*
+ * XXX Delayed fp exceptions when doing a lazy ctx switch XXX
+ */
+asmlinkage void do_fpe(struct pt_regs *regs, unsigned long fcr31)
+{
+	enum ctx_state prev_state;
+	void __user *fault_addr;
+	int sig;
+
+	prev_state = exception_enter();
+	if (notify_die(DIE_FP, "FP exception", regs, 0, current->thread.trap_nr,
+		       SIGFPE) == NOTIFY_STOP)
+		goto out;
+
+	/* Clear FCSR.Cause before enabling interrupts */
+	write_32bit_cp1_register(CP1_STATUS, fcr31 & ~mask_fcr31_x(fcr31));
+	local_irq_enable();
+
+	die_if_kernel("FP exception in kernel code", regs);
+
+	if (fcr31 & FPU_CSR_UNI_X) {
+		/*
+		 * Unimplemented operation exception.  If we've got the full
+		 * software emulator on-board, let's use it...
+		 *
+		 * Force FPU to dump state into task/thread context.  We're
+		 * moving a lot of data here for what is probably a single
+		 * instruction, but the alternative is to pre-decode the FP
+		 * register operands before invoking the emulator, which seems
+		 * a bit extreme for what should be an infrequent event.
+		 */
+
+		/* Run the emulator */
+		sig = fpu_emulator_cop1Handler(regs, &current->thread.fpu, 1,
+					       &fault_addr);
+
+		/*
+		 * We can't allow the emulated instruction to leave any
+		 * enabled Cause bits set in $fcr31.
+		 */
+		fcr31 = mask_fcr31_x(current->thread.fpu.fcr31);
+		current->thread.fpu.fcr31 &= ~fcr31;
+
+		/* Restore the hardware register state */
+		own_fpu(1);	/* Using the FPU again.	 */
+	} else {
+		sig = SIGFPE;
+		fault_addr = (void __user *) regs->cp0_epc;
+	}
+
+	/* Send a signal if required.  */
+	process_fpemu_return(sig, fault_addr, fcr31);
+
+out:
+	exception_exit(prev_state);
+}
+
+/*
+ * MIPS MT processors may have fewer FPU contexts than CPU threads. If we've
+ * emulated more than some threshold number of instructions, force migration to
+ * a "CPU" that has FP support.
+ */
+static void mt_ase_fp_affinity(void)
+{
+#ifdef CONFIG_MIPS_MT_FPAFF
+	if (mt_fpemul_threshold > 0 &&
+	     ((current->thread.emulated_fp++ > mt_fpemul_threshold))) {
+		/*
+		 * If there's no FPU present, or if the application has already
+		 * restricted the allowed set to exclude any CPUs with FPUs,
+		 * we'll skip the procedure.
+		 */
+		if (cpumask_intersects(&current->cpus_mask, &mt_fpu_cpumask)) {
+			cpumask_t tmask;
+
+			current->thread.user_cpus_allowed
+				= current->cpus_mask;
+			cpumask_and(&tmask, &current->cpus_mask,
+				    &mt_fpu_cpumask);
+			set_cpus_allowed_ptr(current, &tmask);
+			set_thread_flag(TIF_FPUBOUND);
+		}
+	}
+#endif /* CONFIG_MIPS_MT_FPAFF */
+}
+
+#else /* !CONFIG_MIPS_FP_SUPPORT */
+
+static int simulate_fp(struct pt_regs *regs, unsigned int opcode,
+		       unsigned long old_epc, unsigned long old_ra)
+{
+	return -1;
+}
+
+#endif /* !CONFIG_MIPS_FP_SUPPORT */
+
+void do_trap_or_bp(struct pt_regs *regs, unsigned int code, int si_code,
+	const char *str)
+{
+	char b[40];
+
+#ifdef CONFIG_KGDB_LOW_LEVEL_TRAP
+	if (kgdb_ll_trap(DIE_TRAP, str, regs, code, current->thread.trap_nr,
+			 SIGTRAP) == NOTIFY_STOP)
+		return;
+#endif /* CONFIG_KGDB_LOW_LEVEL_TRAP */
+
+	if (notify_die(DIE_TRAP, str, regs, code, current->thread.trap_nr,
+		       SIGTRAP) == NOTIFY_STOP)
+		return;
+
+	/*
+	 * A short test says that IRIX 5.3 sends SIGTRAP for all trap
+	 * insns, even for trap and break codes that indicate arithmetic
+	 * failures.  Weird ...
+	 * But should we continue the brokenness???  --macro
+	 */
+	switch (code) {
+	case BRK_OVERFLOW:
+	case BRK_DIVZERO:
+		scnprintf(b, sizeof(b), "%s instruction in kernel code", str);
+		die_if_kernel(b, regs);
+		force_sig_fault(SIGFPE,
+				code == BRK_DIVZERO ? FPE_INTDIV : FPE_INTOVF,
+				(void __user *) regs->cp0_epc);
+		break;
+	case BRK_BUG:
+		die_if_kernel("Kernel bug detected", regs);
+		force_sig(SIGTRAP);
+		break;
+	case BRK_MEMU:
+		/*
+		 * This breakpoint code is used by the FPU emulator to retake
+		 * control of the CPU after executing the instruction from the
+		 * delay slot of an emulated branch.
+		 *
+		 * Terminate if exception was recognized as a delay slot return
+		 * otherwise handle as normal.
+		 */
+		if (do_dsemulret(regs))
+			return;
+
+		die_if_kernel("Math emu break/trap", regs);
+		force_sig(SIGTRAP);
+		break;
+	default:
+		scnprintf(b, sizeof(b), "%s instruction in kernel code", str);
+		die_if_kernel(b, regs);
+		if (si_code) {
+			force_sig_fault(SIGTRAP, si_code, NULL);
+		} else {
+			force_sig(SIGTRAP);
+		}
+	}
+}
+
+asmlinkage void do_bp(struct pt_regs *regs)
+{
+	unsigned long epc = msk_isa16_mode(exception_epc(regs));
+	unsigned int opcode, bcode;
+	enum ctx_state prev_state;
+	bool user = user_mode(regs);
+
+	prev_state = exception_enter();
+	current->thread.trap_nr = (regs->cp0_cause >> 2) & 0x1f;
+	if (get_isa16_mode(regs->cp0_epc)) {
+		u16 instr[2];
+
+		if (__get_inst16(&instr[0], (u16 *)epc, user))
+			goto out_sigsegv;
+
+		if (!cpu_has_mmips) {
+			/* MIPS16e mode */
+			bcode = (instr[0] >> 5) & 0x3f;
+		} else if (mm_insn_16bit(instr[0])) {
+			/* 16-bit microMIPS BREAK */
+			bcode = instr[0] & 0xf;
+		} else {
+			/* 32-bit microMIPS BREAK */
+			if (__get_inst16(&instr[1], (u16 *)(epc + 2), user))
+				goto out_sigsegv;
+			opcode = (instr[0] << 16) | instr[1];
+			bcode = (opcode >> 6) & ((1 << 20) - 1);
+		}
+	} else {
+		if (__get_inst32(&opcode, (u32 *)epc, user))
+			goto out_sigsegv;
+		bcode = (opcode >> 6) & ((1 << 20) - 1);
+	}
+
+	/*
+	 * There is the ancient bug in the MIPS assemblers that the break
+	 * code starts left to bit 16 instead to bit 6 in the opcode.
+	 * Gas is bug-compatible, but not always, grrr...
+	 * We handle both cases with a simple heuristics.  --macro
+	 */
+	if (bcode >= (1 << 10))
+		bcode = ((bcode & ((1 << 10) - 1)) << 10) | (bcode >> 10);
+
+	/*
+	 * notify the kprobe handlers, if instruction is likely to
+	 * pertain to them.
+	 */
+	switch (bcode) {
+	case BRK_UPROBE:
+		if (notify_die(DIE_UPROBE, "uprobe", regs, bcode,
+			       current->thread.trap_nr, SIGTRAP) == NOTIFY_STOP)
+			goto out;
+		else
+			break;
+	case BRK_UPROBE_XOL:
+		if (notify_die(DIE_UPROBE_XOL, "uprobe_xol", regs, bcode,
+			       current->thread.trap_nr, SIGTRAP) == NOTIFY_STOP)
+			goto out;
+		else
+			break;
+	case BRK_KPROBE_BP:
+		if (notify_die(DIE_BREAK, "debug", regs, bcode,
+			       current->thread.trap_nr, SIGTRAP) == NOTIFY_STOP)
+			goto out;
+		else
+			break;
+	case BRK_KPROBE_SSTEPBP:
+		if (notify_die(DIE_SSTEPBP, "single_step", regs, bcode,
+			       current->thread.trap_nr, SIGTRAP) == NOTIFY_STOP)
+			goto out;
+		else
+			break;
+	default:
+		break;
+	}
+
+	do_trap_or_bp(regs, bcode, TRAP_BRKPT, "Break");
+
+out:
+	exception_exit(prev_state);
+	return;
+
+out_sigsegv:
+	force_sig(SIGSEGV);
+	goto out;
+}
+
+asmlinkage void do_tr(struct pt_regs *regs)
+{
+	u32 opcode, tcode = 0;
+	enum ctx_state prev_state;
+	u16 instr[2];
+	bool user = user_mode(regs);
+	unsigned long epc = msk_isa16_mode(exception_epc(regs));
+
+	prev_state = exception_enter();
+	current->thread.trap_nr = (regs->cp0_cause >> 2) & 0x1f;
+	if (get_isa16_mode(regs->cp0_epc)) {
+		if (__get_inst16(&instr[0], (u16 *)(epc + 0), user) ||
+		    __get_inst16(&instr[1], (u16 *)(epc + 2), user))
+			goto out_sigsegv;
+		opcode = (instr[0] << 16) | instr[1];
+		/* Immediate versions don't provide a code.  */
+		if (!(opcode & OPCODE))
+			tcode = (opcode >> 12) & ((1 << 4) - 1);
+	} else {
+		if (__get_inst32(&opcode, (u32 *)epc, user))
+			goto out_sigsegv;
+		/* Immediate versions don't provide a code.  */
+		if (!(opcode & OPCODE))
+			tcode = (opcode >> 6) & ((1 << 10) - 1);
+	}
+
+	do_trap_or_bp(regs, tcode, 0, "Trap");
+
+out:
+	exception_exit(prev_state);
+	return;
+
+out_sigsegv:
+	force_sig(SIGSEGV);
+	goto out;
+}
+
+asmlinkage void do_ri(struct pt_regs *regs)
+{
+	unsigned int __user *epc = (unsigned int __user *)exception_epc(regs);
+	unsigned long old_epc = regs->cp0_epc;
+	unsigned long old31 = regs->regs[31];
+	enum ctx_state prev_state;
+	unsigned int opcode = 0;
+	int status = -1;
+
+	/*
+	 * Avoid any kernel code. Just emulate the R2 instruction
+	 * as quickly as possible.
+	 */
+	if (mipsr2_emulation && cpu_has_mips_r6 &&
+	    likely(user_mode(regs)) &&
+	    likely(get_user(opcode, epc) >= 0)) {
+		unsigned long fcr31 = 0;
+
+		status = mipsr2_decoder(regs, opcode, &fcr31);
+		switch (status) {
+		case 0:
+		case SIGEMT:
+			return;
+		case SIGILL:
+			goto no_r2_instr;
+		default:
+			process_fpemu_return(status,
+					     &current->thread.cp0_baduaddr,
+					     fcr31);
+			return;
+		}
+	}
+
+no_r2_instr:
+
+	prev_state = exception_enter();
+	current->thread.trap_nr = (regs->cp0_cause >> 2) & 0x1f;
+
+	if (notify_die(DIE_RI, "RI Fault", regs, 0, current->thread.trap_nr,
+		       SIGILL) == NOTIFY_STOP)
+		goto out;
+
+	die_if_kernel("Reserved instruction in kernel code", regs);
+
+	if (unlikely(compute_return_epc(regs) < 0))
+		goto out;
+
+	if (!get_isa16_mode(regs->cp0_epc)) {
+		if (unlikely(get_user(opcode, epc) < 0))
+			status = SIGSEGV;
+
+		if (!cpu_has_llsc && status < 0)
+			status = simulate_llsc(regs, opcode);
+
+		if (status < 0)
+			status = simulate_rdhwr_normal(regs, opcode);
+
+		if (status < 0)
+			status = simulate_sync(regs, opcode);
+
+		if (status < 0)
+			status = simulate_fp(regs, opcode, old_epc, old31);
+
+#ifdef CONFIG_CPU_LOONGSON3_CPUCFG_EMULATION
+		if (status < 0)
+			status = simulate_loongson3_cpucfg(regs, opcode);
+#endif
+	} else if (cpu_has_mmips) {
+		unsigned short mmop[2] = { 0 };
+
+		if (unlikely(get_user(mmop[0], (u16 __user *)epc + 0) < 0))
+			status = SIGSEGV;
+		if (unlikely(get_user(mmop[1], (u16 __user *)epc + 1) < 0))
+			status = SIGSEGV;
+		opcode = mmop[0];
+		opcode = (opcode << 16) | mmop[1];
+
+		if (status < 0)
+			status = simulate_rdhwr_mm(regs, opcode);
+	}
+
+	if (status < 0)
+		status = SIGILL;
+
+	if (unlikely(status > 0)) {
+		regs->cp0_epc = old_epc;		/* Undo skip-over.  */
+		regs->regs[31] = old31;
+		force_sig(status);
+	}
+
+out:
+	exception_exit(prev_state);
+}
+
+/*
+ * No lock; only written during early bootup by CPU 0.
+ */
+static RAW_NOTIFIER_HEAD(cu2_chain);
+
+int __ref register_cu2_notifier(struct notifier_block *nb)
+{
+	return raw_notifier_chain_register(&cu2_chain, nb);
+}
+
+int cu2_notifier_call_chain(unsigned long val, void *v)
+{
+	return raw_notifier_call_chain(&cu2_chain, val, v);
+}
+
+static int default_cu2_call(struct notifier_block *nfb, unsigned long action,
+	void *data)
+{
+	struct pt_regs *regs = data;
+
+	die_if_kernel("COP2: Unhandled kernel unaligned access or invalid "
+			      "instruction", regs);
+	force_sig(SIGILL);
+
+	return NOTIFY_OK;
+}
+
+#ifdef CONFIG_MIPS_FP_SUPPORT
+
+static int enable_restore_fp_context(int msa)
+{
+	int err, was_fpu_owner, prior_msa;
+	bool first_fp;
+
+	/* Initialize context if it hasn't been used already */
+	first_fp = init_fp_ctx(current);
+
+	if (first_fp) {
+		preempt_disable();
+		err = own_fpu_inatomic(1);
+		if (msa && !err) {
+			enable_msa();
+			/*
+			 * with MSA enabled, userspace can see MSACSR
+			 * and MSA regs, but the values in them are from
+			 * other task before current task, restore them
+			 * from saved fp/msa context
+			 */
+			write_msa_csr(current->thread.fpu.msacsr);
+			/*
+			 * own_fpu_inatomic(1) just restore low 64bit,
+			 * fix the high 64bit
+			 */
+			init_msa_upper();
+			set_thread_flag(TIF_USEDMSA);
+			set_thread_flag(TIF_MSA_CTX_LIVE);
+		}
+		preempt_enable();
+		return err;
+	}
+
+	/*
+	 * This task has formerly used the FP context.
+	 *
+	 * If this thread has no live MSA vector context then we can simply
+	 * restore the scalar FP context. If it has live MSA vector context
+	 * (that is, it has or may have used MSA since last performing a
+	 * function call) then we'll need to restore the vector context. This
+	 * applies even if we're currently only executing a scalar FP
+	 * instruction. This is because if we were to later execute an MSA
+	 * instruction then we'd either have to:
+	 *
+	 *  - Restore the vector context & clobber any registers modified by
+	 *    scalar FP instructions between now & then.
+	 *
+	 * or
+	 *
+	 *  - Not restore the vector context & lose the most significant bits
+	 *    of all vector registers.
+	 *
+	 * Neither of those options is acceptable. We cannot restore the least
+	 * significant bits of the registers now & only restore the most
+	 * significant bits later because the most significant bits of any
+	 * vector registers whose aliased FP register is modified now will have
+	 * been zeroed. We'd have no way to know that when restoring the vector
+	 * context & thus may load an outdated value for the most significant
+	 * bits of a vector register.
+	 */
+	if (!msa && !thread_msa_context_live())
+		return own_fpu(1);
+
+	/*
+	 * This task is using or has previously used MSA. Thus we require
+	 * that Status.FR == 1.
+	 */
+	preempt_disable();
+	was_fpu_owner = is_fpu_owner();
+	err = own_fpu_inatomic(0);
+	if (err)
+		goto out;
+
+	enable_msa();
+	write_msa_csr(current->thread.fpu.msacsr);
+	set_thread_flag(TIF_USEDMSA);
+
+	/*
+	 * If this is the first time that the task is using MSA and it has
+	 * previously used scalar FP in this time slice then we already nave
+	 * FP context which we shouldn't clobber. We do however need to clear
+	 * the upper 64b of each vector register so that this task has no
+	 * opportunity to see data left behind by another.
+	 */
+	prior_msa = test_and_set_thread_flag(TIF_MSA_CTX_LIVE);
+	if (!prior_msa && was_fpu_owner) {
+		init_msa_upper();
+
+		goto out;
+	}
+
+	if (!prior_msa) {
+		/*
+		 * Restore the least significant 64b of each vector register
+		 * from the existing scalar FP context.
+		 */
+		_restore_fp(current);
+
+		/*
+		 * The task has not formerly used MSA, so clear the upper 64b
+		 * of each vector register such that it cannot see data left
+		 * behind by another task.
+		 */
+		init_msa_upper();
+	} else {
+		/* We need to restore the vector context. */
+		restore_msa(current);
+
+		/* Restore the scalar FP control & status register */
+		if (!was_fpu_owner)
+			write_32bit_cp1_register(CP1_STATUS,
+						 current->thread.fpu.fcr31);
+	}
+
+out:
+	preempt_enable();
+
+	return 0;
+}
+
+#else /* !CONFIG_MIPS_FP_SUPPORT */
+
+static int enable_restore_fp_context(int msa)
+{
+	return SIGILL;
+}
+
+#endif /* CONFIG_MIPS_FP_SUPPORT */
+
+asmlinkage void do_cpu(struct pt_regs *regs)
+{
+	enum ctx_state prev_state;
+	unsigned int __user *epc;
+	unsigned long old_epc, old31;
+	unsigned int opcode;
+	unsigned int cpid;
+	int status;
+
+	prev_state = exception_enter();
+	cpid = (regs->cp0_cause >> CAUSEB_CE) & 3;
+
+	if (cpid != 2)
+		die_if_kernel("do_cpu invoked from kernel context!", regs);
+
+	switch (cpid) {
+	case 0:
+		epc = (unsigned int __user *)exception_epc(regs);
+		old_epc = regs->cp0_epc;
+		old31 = regs->regs[31];
+		opcode = 0;
+		status = -1;
+
+		if (unlikely(compute_return_epc(regs) < 0))
+			break;
+
+		if (!get_isa16_mode(regs->cp0_epc)) {
+			if (unlikely(get_user(opcode, epc) < 0))
+				status = SIGSEGV;
+
+			if (!cpu_has_llsc && status < 0)
+				status = simulate_llsc(regs, opcode);
+		}
+
+		if (status < 0)
+			status = SIGILL;
+
+		if (unlikely(status > 0)) {
+			regs->cp0_epc = old_epc;	/* Undo skip-over.  */
+			regs->regs[31] = old31;
+			force_sig(status);
+		}
+
+		break;
+
+#ifdef CONFIG_MIPS_FP_SUPPORT
+	case 3:
+		/*
+		 * The COP3 opcode space and consequently the CP0.Status.CU3
+		 * bit and the CP0.Cause.CE=3 encoding have been removed as
+		 * of the MIPS III ISA.  From the MIPS IV and MIPS32r2 ISAs
+		 * up the space has been reused for COP1X instructions, that
+		 * are enabled by the CP0.Status.CU1 bit and consequently
+		 * use the CP0.Cause.CE=1 encoding for Coprocessor Unusable
+		 * exceptions.  Some FPU-less processors that implement one
+		 * of these ISAs however use this code erroneously for COP1X
+		 * instructions.  Therefore we redirect this trap to the FP
+		 * emulator too.
+		 */
+		if (raw_cpu_has_fpu || !cpu_has_mips_4_5_64_r2_r6) {
+			force_sig(SIGILL);
+			break;
+		}
+		fallthrough;
+	case 1: {
+		void __user *fault_addr;
+		unsigned long fcr31;
+		int err, sig;
+
+		err = enable_restore_fp_context(0);
+
+		if (raw_cpu_has_fpu && !err)
+			break;
+
+		sig = fpu_emulator_cop1Handler(regs, &current->thread.fpu, 0,
+					       &fault_addr);
+
+		/*
+		 * We can't allow the emulated instruction to leave
+		 * any enabled Cause bits set in $fcr31.
+		 */
+		fcr31 = mask_fcr31_x(current->thread.fpu.fcr31);
+		current->thread.fpu.fcr31 &= ~fcr31;
+
+		/* Send a signal if required.  */
+		if (!process_fpemu_return(sig, fault_addr, fcr31) && !err)
+			mt_ase_fp_affinity();
+
+		break;
+	}
+#else /* CONFIG_MIPS_FP_SUPPORT */
+	case 1:
+	case 3:
+		force_sig(SIGILL);
+		break;
+#endif /* CONFIG_MIPS_FP_SUPPORT */
+
+	case 2:
+		raw_notifier_call_chain(&cu2_chain, CU2_EXCEPTION, regs);
+		break;
+	}
+
+	exception_exit(prev_state);
+}
+
+asmlinkage void do_msa_fpe(struct pt_regs *regs, unsigned int msacsr)
+{
+	enum ctx_state prev_state;
+
+	prev_state = exception_enter();
+	current->thread.trap_nr = (regs->cp0_cause >> 2) & 0x1f;
+	if (notify_die(DIE_MSAFP, "MSA FP exception", regs, 0,
+		       current->thread.trap_nr, SIGFPE) == NOTIFY_STOP)
+		goto out;
+
+	/* Clear MSACSR.Cause before enabling interrupts */
+	write_msa_csr(msacsr & ~MSA_CSR_CAUSEF);
+	local_irq_enable();
+
+	die_if_kernel("do_msa_fpe invoked from kernel context!", regs);
+	force_sig(SIGFPE);
+out:
+	exception_exit(prev_state);
+}
+
+asmlinkage void do_msa(struct pt_regs *regs)
+{
+	enum ctx_state prev_state;
+	int err;
+
+	prev_state = exception_enter();
+
+	if (!cpu_has_msa || test_thread_flag(TIF_32BIT_FPREGS)) {
+		force_sig(SIGILL);
+		goto out;
+	}
+
+	die_if_kernel("do_msa invoked from kernel context!", regs);
+
+	err = enable_restore_fp_context(1);
+	if (err)
+		force_sig(SIGILL);
+out:
+	exception_exit(prev_state);
+}
+
+asmlinkage void do_mdmx(struct pt_regs *regs)
+{
+	enum ctx_state prev_state;
+
+	prev_state = exception_enter();
+	force_sig(SIGILL);
+	exception_exit(prev_state);
+}
+
+/*
+ * Called with interrupts disabled.
+ */
+asmlinkage void do_watch(struct pt_regs *regs)
+{
+	enum ctx_state prev_state;
+
+	prev_state = exception_enter();
+	/*
+	 * Clear WP (bit 22) bit of cause register so we don't loop
+	 * forever.
+	 */
+	clear_c0_cause(CAUSEF_WP);
+
+	/*
+	 * If the current thread has the watch registers loaded, save
+	 * their values and send SIGTRAP.  Otherwise another thread
+	 * left the registers set, clear them and continue.
+	 */
+	if (test_tsk_thread_flag(current, TIF_LOAD_WATCH)) {
+		mips_read_watch_registers();
+		local_irq_enable();
+		force_sig_fault(SIGTRAP, TRAP_HWBKPT, NULL);
+	} else {
+		mips_clear_watch_registers();
+		local_irq_enable();
+	}
+	exception_exit(prev_state);
+}
+
+asmlinkage void do_mcheck(struct pt_regs *regs)
+{
+	int multi_match = regs->cp0_status & ST0_TS;
+	enum ctx_state prev_state;
+
+	prev_state = exception_enter();
+	show_regs(regs);
+
+	if (multi_match) {
+		dump_tlb_regs();
+		pr_info("\n");
+		dump_tlb_all();
+	}
+
+	show_code((void *)regs->cp0_epc, user_mode(regs));
+
+	/*
+	 * Some chips may have other causes of machine check (e.g. SB1
+	 * graduation timer)
+	 */
+	panic("Caught Machine Check exception - %scaused by multiple "
+	      "matching entries in the TLB.",
+	      (multi_match) ? "" : "not ");
+}
+
+asmlinkage void do_mt(struct pt_regs *regs)
+{
+	int subcode;
+
+	subcode = (read_vpe_c0_vpecontrol() & VPECONTROL_EXCPT)
+			>> VPECONTROL_EXCPT_SHIFT;
+	switch (subcode) {
+	case 0:
+		printk(KERN_DEBUG "Thread Underflow\n");
+		break;
+	case 1:
+		printk(KERN_DEBUG "Thread Overflow\n");
+		break;
+	case 2:
+		printk(KERN_DEBUG "Invalid YIELD Qualifier\n");
+		break;
+	case 3:
+		printk(KERN_DEBUG "Gating Storage Exception\n");
+		break;
+	case 4:
+		printk(KERN_DEBUG "YIELD Scheduler Exception\n");
+		break;
+	case 5:
+		printk(KERN_DEBUG "Gating Storage Scheduler Exception\n");
+		break;
+	default:
+		printk(KERN_DEBUG "*** UNKNOWN THREAD EXCEPTION %d ***\n",
+			subcode);
+		break;
+	}
+	die_if_kernel("MIPS MT Thread exception in kernel", regs);
+
+	force_sig(SIGILL);
+}
+
+
+asmlinkage void do_dsp(struct pt_regs *regs)
+{
+	if (cpu_has_dsp)
+		panic("Unexpected DSP exception");
+
+	force_sig(SIGILL);
+}
+
+asmlinkage void do_reserved(struct pt_regs *regs)
+{
+	/*
+	 * Game over - no way to handle this if it ever occurs.	 Most probably
+	 * caused by a new unknown cpu type or after another deadly
+	 * hard/software error.
+	 */
+	show_regs(regs);
+	panic("Caught reserved exception %ld - should not happen.",
+	      (regs->cp0_cause & 0x7f) >> 2);
+}
+
+static int __initdata l1parity = 1;
+static int __init nol1parity(char *s)
+{
+	l1parity = 0;
+	return 1;
+}
+__setup("nol1par", nol1parity);
+static int __initdata l2parity = 1;
+static int __init nol2parity(char *s)
+{
+	l2parity = 0;
+	return 1;
+}
+__setup("nol2par", nol2parity);
+
+/*
+ * Some MIPS CPUs can enable/disable for cache parity detection, but do
+ * it different ways.
+ */
+static inline __init void parity_protection_init(void)
+{
+#define ERRCTL_PE	0x80000000
+#define ERRCTL_L2P	0x00800000
+
+	if (mips_cm_revision() >= CM_REV_CM3) {
+		ulong gcr_ectl, cp0_ectl;
+
+		/*
+		 * With CM3 systems we need to ensure that the L1 & L2
+		 * parity enables are set to the same value, since this
+		 * is presumed by the hardware engineers.
+		 *
+		 * If the user disabled either of L1 or L2 ECC checking,
+		 * disable both.
+		 */
+		l1parity &= l2parity;
+		l2parity &= l1parity;
+
+		/* Probe L1 ECC support */
+		cp0_ectl = read_c0_ecc();
+		write_c0_ecc(cp0_ectl | ERRCTL_PE);
+		back_to_back_c0_hazard();
+		cp0_ectl = read_c0_ecc();
+
+		/* Probe L2 ECC support */
+		gcr_ectl = read_gcr_err_control();
+
+		if (!(gcr_ectl & CM_GCR_ERR_CONTROL_L2_ECC_SUPPORT) ||
+		    !(cp0_ectl & ERRCTL_PE)) {
+			/*
+			 * One of L1 or L2 ECC checking isn't supported,
+			 * so we cannot enable either.
+			 */
+			l1parity = l2parity = 0;
+		}
+
+		/* Configure L1 ECC checking */
+		if (l1parity)
+			cp0_ectl |= ERRCTL_PE;
+		else
+			cp0_ectl &= ~ERRCTL_PE;
+		write_c0_ecc(cp0_ectl);
+		back_to_back_c0_hazard();
+		WARN_ON(!!(read_c0_ecc() & ERRCTL_PE) != l1parity);
+
+		/* Configure L2 ECC checking */
+		if (l2parity)
+			gcr_ectl |= CM_GCR_ERR_CONTROL_L2_ECC_EN;
+		else
+			gcr_ectl &= ~CM_GCR_ERR_CONTROL_L2_ECC_EN;
+		write_gcr_err_control(gcr_ectl);
+		gcr_ectl = read_gcr_err_control();
+		gcr_ectl &= CM_GCR_ERR_CONTROL_L2_ECC_EN;
+		WARN_ON(!!gcr_ectl != l2parity);
+
+		pr_info("Cache parity protection %sabled\n",
+			l1parity ? "en" : "dis");
+		return;
+	}
+
+	switch (current_cpu_type()) {
+	case CPU_24K:
+	case CPU_34K:
+	case CPU_74K:
+	case CPU_1004K:
+	case CPU_1074K:
+	case CPU_INTERAPTIV:
+	case CPU_PROAPTIV:
+	case CPU_P5600:
+	case CPU_QEMU_GENERIC:
+	case CPU_P6600:
+		{
+			unsigned long errctl;
+			unsigned int l1parity_present, l2parity_present;
+
+			errctl = read_c0_ecc();
+			errctl &= ~(ERRCTL_PE|ERRCTL_L2P);
+
+			/* probe L1 parity support */
+			write_c0_ecc(errctl | ERRCTL_PE);
+			back_to_back_c0_hazard();
+			l1parity_present = (read_c0_ecc() & ERRCTL_PE);
+
+			/* probe L2 parity support */
+			write_c0_ecc(errctl|ERRCTL_L2P);
+			back_to_back_c0_hazard();
+			l2parity_present = (read_c0_ecc() & ERRCTL_L2P);
+
+			if (l1parity_present && l2parity_present) {
+				if (l1parity)
+					errctl |= ERRCTL_PE;
+				if (l1parity ^ l2parity)
+					errctl |= ERRCTL_L2P;
+			} else if (l1parity_present) {
+				if (l1parity)
+					errctl |= ERRCTL_PE;
+			} else if (l2parity_present) {
+				if (l2parity)
+					errctl |= ERRCTL_L2P;
+			} else {
+				/* No parity available */
+			}
+
+			printk(KERN_INFO "Writing ErrCtl register=%08lx\n", errctl);
+
+			write_c0_ecc(errctl);
+			back_to_back_c0_hazard();
+			errctl = read_c0_ecc();
+			printk(KERN_INFO "Readback ErrCtl register=%08lx\n", errctl);
+
+			if (l1parity_present)
+				printk(KERN_INFO "Cache parity protection %sabled\n",
+				       (errctl & ERRCTL_PE) ? "en" : "dis");
+
+			if (l2parity_present) {
+				if (l1parity_present && l1parity)
+					errctl ^= ERRCTL_L2P;
+				printk(KERN_INFO "L2 cache parity protection %sabled\n",
+				       (errctl & ERRCTL_L2P) ? "en" : "dis");
+			}
+		}
+		break;
+
+	case CPU_5KC:
+	case CPU_5KE:
+	case CPU_LOONGSON32:
+		write_c0_ecc(0x80000000);
+		back_to_back_c0_hazard();
+		/* Set the PE bit (bit 31) in the c0_errctl register. */
+		printk(KERN_INFO "Cache parity protection %sabled\n",
+		       (read_c0_ecc() & 0x80000000) ? "en" : "dis");
+		break;
+	case CPU_20KC:
+	case CPU_25KF:
+		/* Clear the DE bit (bit 16) in the c0_status register. */
+		printk(KERN_INFO "Enable cache parity protection for "
+		       "MIPS 20KC/25KF CPUs.\n");
+		clear_c0_status(ST0_DE);
+		break;
+	default:
+		break;
+	}
+}
+
+asmlinkage void cache_parity_error(void)
+{
+	const int field = 2 * sizeof(unsigned long);
+	unsigned int reg_val;
+
+	/* For the moment, report the problem and hang. */
+	printk("Cache error exception:\n");
+	printk("cp0_errorepc == %0*lx\n", field, read_c0_errorepc());
+	reg_val = read_c0_cacheerr();
+	printk("c0_cacheerr == %08x\n", reg_val);
+
+	printk("Decoded c0_cacheerr: %s cache fault in %s reference.\n",
+	       reg_val & (1<<30) ? "secondary" : "primary",
+	       reg_val & (1<<31) ? "data" : "insn");
+	if ((cpu_has_mips_r2_r6) &&
+	    ((current_cpu_data.processor_id & 0xff0000) == PRID_COMP_MIPS)) {
+		pr_err("Error bits: %s%s%s%s%s%s%s%s\n",
+			reg_val & (1<<29) ? "ED " : "",
+			reg_val & (1<<28) ? "ET " : "",
+			reg_val & (1<<27) ? "ES " : "",
+			reg_val & (1<<26) ? "EE " : "",
+			reg_val & (1<<25) ? "EB " : "",
+			reg_val & (1<<24) ? "EI " : "",
+			reg_val & (1<<23) ? "E1 " : "",
+			reg_val & (1<<22) ? "E0 " : "");
+	} else {
+		pr_err("Error bits: %s%s%s%s%s%s%s\n",
+			reg_val & (1<<29) ? "ED " : "",
+			reg_val & (1<<28) ? "ET " : "",
+			reg_val & (1<<26) ? "EE " : "",
+			reg_val & (1<<25) ? "EB " : "",
+			reg_val & (1<<24) ? "EI " : "",
+			reg_val & (1<<23) ? "E1 " : "",
+			reg_val & (1<<22) ? "E0 " : "");
+	}
+	printk("IDX: 0x%08x\n", reg_val & ((1<<22)-1));
+
+#if defined(CONFIG_CPU_MIPS32) || defined(CONFIG_CPU_MIPS64)
+	if (reg_val & (1<<22))
+		printk("DErrAddr0: 0x%0*lx\n", field, read_c0_derraddr0());
+
+	if (reg_val & (1<<23))
+		printk("DErrAddr1: 0x%0*lx\n", field, read_c0_derraddr1());
+#endif
+
+	panic("Can't handle the cache error!");
+}
+
+asmlinkage void do_ftlb(void)
+{
+	const int field = 2 * sizeof(unsigned long);
+	unsigned int reg_val;
+
+	/* For the moment, report the problem and hang. */
+	if ((cpu_has_mips_r2_r6) &&
+	    (((current_cpu_data.processor_id & 0xff0000) == PRID_COMP_MIPS) ||
+	    ((current_cpu_data.processor_id & 0xff0000) == PRID_COMP_LOONGSON))) {
+		pr_err("FTLB error exception, cp0_ecc=0x%08x:\n",
+		       read_c0_ecc());
+		pr_err("cp0_errorepc == %0*lx\n", field, read_c0_errorepc());
+		reg_val = read_c0_cacheerr();
+		pr_err("c0_cacheerr == %08x\n", reg_val);
+
+		if ((reg_val & 0xc0000000) == 0xc0000000) {
+			pr_err("Decoded c0_cacheerr: FTLB parity error\n");
+		} else {
+			pr_err("Decoded c0_cacheerr: %s cache fault in %s reference.\n",
+			       reg_val & (1<<30) ? "secondary" : "primary",
+			       reg_val & (1<<31) ? "data" : "insn");
+		}
+	} else {
+		pr_err("FTLB error exception\n");
+	}
+	/* Just print the cacheerr bits for now */
+	cache_parity_error();
+}
+
+asmlinkage void do_gsexc(struct pt_regs *regs, u32 diag1)
+{
+	u32 exccode = (diag1 & LOONGSON_DIAG1_EXCCODE) >>
+			LOONGSON_DIAG1_EXCCODE_SHIFT;
+	enum ctx_state prev_state;
+
+	prev_state = exception_enter();
+
+	switch (exccode) {
+	case 0x08:
+		/* Undocumented exception, will trigger on certain
+		 * also-undocumented instructions accessible from userspace.
+		 * Processor state is not otherwise corrupted, but currently
+		 * we don't know how to proceed. Maybe there is some
+		 * undocumented control flag to enable the instructions?
+		 */
+		force_sig(SIGILL);
+		break;
+
+	default:
+		/* None of the other exceptions, documented or not, have
+		 * further details given; none are encountered in the wild
+		 * either. Panic in case some of them turn out to be fatal.
+		 */
+		show_regs(regs);
+		panic("Unhandled Loongson exception - GSCause = %08x", diag1);
+	}
+
+	exception_exit(prev_state);
+}
+
+/*
+ * SDBBP EJTAG debug exception handler.
+ * We skip the instruction and return to the next instruction.
+ */
+void ejtag_exception_handler(struct pt_regs *regs)
+{
+	const int field = 2 * sizeof(unsigned long);
+	unsigned long depc, old_epc, old_ra;
+	unsigned int debug;
+
+	printk(KERN_DEBUG "SDBBP EJTAG debug exception - not handled yet, just ignored!\n");
+	depc = read_c0_depc();
+	debug = read_c0_debug();
+	printk(KERN_DEBUG "c0_depc = %0*lx, DEBUG = %08x\n", field, depc, debug);
+	if (debug & 0x80000000) {
+		/*
+		 * In branch delay slot.
+		 * We cheat a little bit here and use EPC to calculate the
+		 * debug return address (DEPC). EPC is restored after the
+		 * calculation.
+		 */
+		old_epc = regs->cp0_epc;
+		old_ra = regs->regs[31];
+		regs->cp0_epc = depc;
+		compute_return_epc(regs);
+		depc = regs->cp0_epc;
+		regs->cp0_epc = old_epc;
+		regs->regs[31] = old_ra;
+	} else
+		depc += 4;
+	write_c0_depc(depc);
+
+#if 0
+	printk(KERN_DEBUG "\n\n----- Enable EJTAG single stepping ----\n\n");
+	write_c0_debug(debug | 0x100);
+#endif
+}
+
+/*
+ * NMI exception handler.
+ * No lock; only written during early bootup by CPU 0.
+ */
+static RAW_NOTIFIER_HEAD(nmi_chain);
+
+int register_nmi_notifier(struct notifier_block *nb)
+{
+	return raw_notifier_chain_register(&nmi_chain, nb);
+}
+
+void __noreturn nmi_exception_handler(struct pt_regs *regs)
+{
+	char str[100];
+
+	nmi_enter();
+	raw_notifier_call_chain(&nmi_chain, 0, regs);
+	bust_spinlocks(1);
+	snprintf(str, 100, "CPU%d NMI taken, CP0_EPC=%lx\n",
+		 smp_processor_id(), regs->cp0_epc);
+	regs->cp0_epc = read_c0_errorepc();
+	die(str, regs);
+	nmi_exit();
+}
+
+unsigned long ebase;
+EXPORT_SYMBOL_GPL(ebase);
+unsigned long exception_handlers[32];
+unsigned long vi_handlers[64];
+
+void reserve_exception_space(phys_addr_t addr, unsigned long size)
+{
+	memblock_reserve(addr, size);
+}
+
+void __init *set_except_vector(int n, void *addr)
+{
+	unsigned long handler = (unsigned long) addr;
+	unsigned long old_handler;
+
+#ifdef CONFIG_CPU_MICROMIPS
+	/*
+	 * Only the TLB handlers are cache aligned with an even
+	 * address. All other handlers are on an odd address and
+	 * require no modification. Otherwise, MIPS32 mode will
+	 * be entered when handling any TLB exceptions. That
+	 * would be bad...since we must stay in microMIPS mode.
+	 */
+	if (!(handler & 0x1))
+		handler |= 1;
+#endif
+	old_handler = xchg(&exception_handlers[n], handler);
+
+	if (n == 0 && cpu_has_divec) {
+#ifdef CONFIG_CPU_MICROMIPS
+		unsigned long jump_mask = ~((1 << 27) - 1);
+#else
+		unsigned long jump_mask = ~((1 << 28) - 1);
+#endif
+		u32 *buf = (u32 *)(ebase + 0x200);
+		unsigned int k0 = 26;
+		if ((handler & jump_mask) == ((ebase + 0x200) & jump_mask)) {
+			uasm_i_j(&buf, handler & ~jump_mask);
+			uasm_i_nop(&buf);
+		} else {
+			UASM_i_LA(&buf, k0, handler);
+			uasm_i_jr(&buf, k0);
+			uasm_i_nop(&buf);
+		}
+		local_flush_icache_range(ebase + 0x200, (unsigned long)buf);
+	}
+	return (void *)old_handler;
+}
+
+static void do_default_vi(void)
+{
+	show_regs(get_irq_regs());
+	panic("Caught unexpected vectored interrupt.");
+}
+
+static void *set_vi_srs_handler(int n, vi_handler_t addr, int srs)
+{
+	unsigned long handler;
+	unsigned long old_handler = vi_handlers[n];
+	int srssets = current_cpu_data.srsets;
+	u16 *h;
+	unsigned char *b;
+
+	BUG_ON(!cpu_has_veic && !cpu_has_vint);
+
+	if (addr == NULL) {
+		handler = (unsigned long) do_default_vi;
+		srs = 0;
+	} else
+		handler = (unsigned long) addr;
+	vi_handlers[n] = handler;
+
+	b = (unsigned char *)(ebase + 0x200 + n*VECTORSPACING);
+
+	if (srs >= srssets)
+		panic("Shadow register set %d not supported", srs);
+
+	if (cpu_has_veic) {
+		if (board_bind_eic_interrupt)
+			board_bind_eic_interrupt(n, srs);
+	} else if (cpu_has_vint) {
+		/* SRSMap is only defined if shadow sets are implemented */
+		if (srssets > 1)
+			change_c0_srsmap(0xf << n*4, srs << n*4);
+	}
+
+	if (srs == 0) {
+		/*
+		 * If no shadow set is selected then use the default handler
+		 * that does normal register saving and standard interrupt exit
+		 */
+		extern const u8 except_vec_vi[], except_vec_vi_lui[];
+		extern const u8 except_vec_vi_ori[], except_vec_vi_end[];
+		extern const u8 rollback_except_vec_vi[];
+		const u8 *vec_start = using_rollback_handler() ?
+				      rollback_except_vec_vi : except_vec_vi;
+#if defined(CONFIG_CPU_MICROMIPS) || defined(CONFIG_CPU_BIG_ENDIAN)
+		const int lui_offset = except_vec_vi_lui - vec_start + 2;
+		const int ori_offset = except_vec_vi_ori - vec_start + 2;
+#else
+		const int lui_offset = except_vec_vi_lui - vec_start;
+		const int ori_offset = except_vec_vi_ori - vec_start;
+#endif
+		const int handler_len = except_vec_vi_end - vec_start;
+
+		if (handler_len > VECTORSPACING) {
+			/*
+			 * Sigh... panicing won't help as the console
+			 * is probably not configured :(
+			 */
+			panic("VECTORSPACING too small");
+		}
+
+		set_handler(((unsigned long)b - ebase), vec_start,
+#ifdef CONFIG_CPU_MICROMIPS
+				(handler_len - 1));
+#else
+				handler_len);
+#endif
+		h = (u16 *)(b + lui_offset);
+		*h = (handler >> 16) & 0xffff;
+		h = (u16 *)(b + ori_offset);
+		*h = (handler & 0xffff);
+		local_flush_icache_range((unsigned long)b,
+					 (unsigned long)(b+handler_len));
+	}
+	else {
+		/*
+		 * In other cases jump directly to the interrupt handler. It
+		 * is the handler's responsibility to save registers if required
+		 * (eg hi/lo) and return from the exception using "eret".
+		 */
+		u32 insn;
+
+		h = (u16 *)b;
+		/* j handler */
+#ifdef CONFIG_CPU_MICROMIPS
+		insn = 0xd4000000 | (((u32)handler & 0x07ffffff) >> 1);
+#else
+		insn = 0x08000000 | (((u32)handler & 0x0fffffff) >> 2);
+#endif
+		h[0] = (insn >> 16) & 0xffff;
+		h[1] = insn & 0xffff;
+		h[2] = 0;
+		h[3] = 0;
+		local_flush_icache_range((unsigned long)b,
+					 (unsigned long)(b+8));
+	}
+
+	return (void *)old_handler;
+}
+
+void *set_vi_handler(int n, vi_handler_t addr)
+{
+	return set_vi_srs_handler(n, addr, 0);
+}
+
+extern void tlb_init(void);
+
+/*
+ * Timer interrupt
+ */
+int cp0_compare_irq;
+EXPORT_SYMBOL_GPL(cp0_compare_irq);
+int cp0_compare_irq_shift;
+
+/*
+ * Performance counter IRQ or -1 if shared with timer
+ */
+int cp0_perfcount_irq;
+EXPORT_SYMBOL_GPL(cp0_perfcount_irq);
+
+/*
+ * Fast debug channel IRQ or -1 if not present
+ */
+int cp0_fdc_irq;
+EXPORT_SYMBOL_GPL(cp0_fdc_irq);
+
+static int noulri;
+
+static int __init ulri_disable(char *s)
+{
+	pr_info("Disabling ulri\n");
+	noulri = 1;
+
+	return 1;
+}
+__setup("noulri", ulri_disable);
+
+/* configure STATUS register */
+static void configure_status(void)
+{
+	/*
+	 * Disable coprocessors and select 32-bit or 64-bit addressing
+	 * and the 16/32 or 32/32 FPR register model.  Reset the BEV
+	 * flag that some firmware may have left set and the TS bit (for
+	 * IP27).  Set XX for ISA IV code to work.
+	 */
+	unsigned int status_set = ST0_KERNEL_CUMASK;
+#ifdef CONFIG_64BIT
+	status_set |= ST0_FR|ST0_KX|ST0_SX|ST0_UX;
+#endif
+	if (current_cpu_data.isa_level & MIPS_CPU_ISA_IV)
+		status_set |= ST0_XX;
+	if (cpu_has_dsp)
+		status_set |= ST0_MX;
+
+	change_c0_status(ST0_CU|ST0_MX|ST0_RE|ST0_FR|ST0_BEV|ST0_TS|ST0_KX|ST0_SX|ST0_UX,
+			 status_set);
+	back_to_back_c0_hazard();
+}
+
+unsigned int hwrena;
+EXPORT_SYMBOL_GPL(hwrena);
+
+/* configure HWRENA register */
+static void configure_hwrena(void)
+{
+	hwrena = cpu_hwrena_impl_bits;
+
+	if (cpu_has_mips_r2_r6)
+		hwrena |= MIPS_HWRENA_CPUNUM |
+			  MIPS_HWRENA_SYNCISTEP |
+			  MIPS_HWRENA_CC |
+			  MIPS_HWRENA_CCRES;
+
+	if (!noulri && cpu_has_userlocal)
+		hwrena |= MIPS_HWRENA_ULR;
+
+	if (hwrena)
+		write_c0_hwrena(hwrena);
+}
+
+static void configure_exception_vector(void)
+{
+	if (cpu_has_mips_r2_r6) {
+		unsigned long sr = set_c0_status(ST0_BEV);
+		/* If available, use WG to set top bits of EBASE */
+		if (cpu_has_ebase_wg) {
+#ifdef CONFIG_64BIT
+			write_c0_ebase_64(ebase | MIPS_EBASE_WG);
+#else
+			write_c0_ebase(ebase | MIPS_EBASE_WG);
+#endif
+		}
+		write_c0_ebase(ebase);
+		write_c0_status(sr);
+	}
+	if (cpu_has_veic || cpu_has_vint) {
+		/* Setting vector spacing enables EI/VI mode  */
+		change_c0_intctl(0x3e0, VECTORSPACING);
+	}
+	if (cpu_has_divec) {
+		if (cpu_has_mipsmt) {
+			unsigned int vpflags = dvpe();
+			set_c0_cause(CAUSEF_IV);
+			evpe(vpflags);
+		} else
+			set_c0_cause(CAUSEF_IV);
+	}
+}
+
+void per_cpu_trap_init(bool is_boot_cpu)
+{
+	unsigned int cpu = smp_processor_id();
+
+	configure_status();
+	configure_hwrena();
+
+	configure_exception_vector();
+
+	/*
+	 * Before R2 both interrupt numbers were fixed to 7, so on R2 only:
+	 *
+	 *  o read IntCtl.IPTI to determine the timer interrupt
+	 *  o read IntCtl.IPPCI to determine the performance counter interrupt
+	 *  o read IntCtl.IPFDC to determine the fast debug channel interrupt
+	 */
+	if (cpu_has_mips_r2_r6) {
+		cp0_compare_irq_shift = CAUSEB_TI - CAUSEB_IP;
+		cp0_compare_irq = (read_c0_intctl() >> INTCTLB_IPTI) & 7;
+		cp0_perfcount_irq = (read_c0_intctl() >> INTCTLB_IPPCI) & 7;
+		cp0_fdc_irq = (read_c0_intctl() >> INTCTLB_IPFDC) & 7;
+		if (!cp0_fdc_irq)
+			cp0_fdc_irq = -1;
+
+	} else {
+		cp0_compare_irq = CP0_LEGACY_COMPARE_IRQ;
+		cp0_compare_irq_shift = CP0_LEGACY_PERFCNT_IRQ;
+		cp0_perfcount_irq = -1;
+		cp0_fdc_irq = -1;
+	}
+
+	if (cpu_has_mmid)
+		cpu_data[cpu].asid_cache = 0;
+	else if (!cpu_data[cpu].asid_cache)
+		cpu_data[cpu].asid_cache = asid_first_version(cpu);
+
+	mmgrab(&init_mm);
+	current->active_mm = &init_mm;
+	BUG_ON(current->mm);
+	enter_lazy_tlb(&init_mm, current);
+
+	/* Boot CPU's cache setup in setup_arch(). */
+	if (!is_boot_cpu)
+		cpu_cache_init();
+	tlb_init();
+	TLBMISS_HANDLER_SETUP();
+}
+
+/* Install CPU exception handler */
+void set_handler(unsigned long offset, const void *addr, unsigned long size)
+{
+#ifdef CONFIG_CPU_MICROMIPS
+	memcpy((void *)(ebase + offset), ((unsigned char *)addr - 1), size);
+#else
+	memcpy((void *)(ebase + offset), addr, size);
+#endif
+	local_flush_icache_range(ebase + offset, ebase + offset + size);
+}
+
+static const char panic_null_cerr[] =
+	"Trying to set NULL cache error exception handler\n";
+
+/*
+ * Install uncached CPU exception handler.
+ * This is suitable only for the cache error exception which is the only
+ * exception handler that is being run uncached.
+ */
+void set_uncached_handler(unsigned long offset, void *addr,
+	unsigned long size)
+{
+	unsigned long uncached_ebase = CKSEG1ADDR(ebase);
+
+	if (!addr)
+		panic(panic_null_cerr);
+
+	memcpy((void *)(uncached_ebase + offset), addr, size);
+}
+
+static int __initdata rdhwr_noopt;
+static int __init set_rdhwr_noopt(char *str)
+{
+	rdhwr_noopt = 1;
+	return 1;
+}
+
+__setup("rdhwr_noopt", set_rdhwr_noopt);
+
+void __init trap_init(void)
+{
+	extern char except_vec3_generic;
+	extern char except_vec4;
+	extern char except_vec3_r4000;
+	unsigned long i, vec_size;
+	phys_addr_t ebase_pa;
+
+	check_wait();
+
+	if (!cpu_has_mips_r2_r6) {
+		ebase = CAC_BASE;
+		vec_size = 0x400;
+	} else {
+		if (cpu_has_veic || cpu_has_vint)
+			vec_size = 0x200 + VECTORSPACING*64;
+		else
+			vec_size = PAGE_SIZE;
+
+		ebase_pa = memblock_phys_alloc(vec_size, 1 << fls(vec_size));
+		if (!ebase_pa)
+			panic("%s: Failed to allocate %lu bytes align=0x%x\n",
+			      __func__, vec_size, 1 << fls(vec_size));
+
+		/*
+		 * Try to ensure ebase resides in KSeg0 if possible.
+		 *
+		 * It shouldn't generally be in XKPhys on MIPS64 to avoid
+		 * hitting a poorly defined exception base for Cache Errors.
+		 * The allocation is likely to be in the low 512MB of physical,
+		 * in which case we should be able to convert to KSeg0.
+		 *
+		 * EVA is special though as it allows segments to be rearranged
+		 * and to become uncached during cache error handling.
+		 */
+		if (!IS_ENABLED(CONFIG_EVA) && !WARN_ON(ebase_pa >= 0x20000000))
+			ebase = CKSEG0ADDR(ebase_pa);
+		else
+			ebase = (unsigned long)phys_to_virt(ebase_pa);
+	}
+
+	if (cpu_has_mmips) {
+		unsigned int config3 = read_c0_config3();
+
+		if (IS_ENABLED(CONFIG_CPU_MICROMIPS))
+			write_c0_config3(config3 | MIPS_CONF3_ISA_OE);
+		else
+			write_c0_config3(config3 & ~MIPS_CONF3_ISA_OE);
+	}
+
+	if (board_ebase_setup)
+		board_ebase_setup();
+	per_cpu_trap_init(true);
+	memblock_set_bottom_up(false);
+
+	/*
+	 * Copy the generic exception handlers to their final destination.
+	 * This will be overridden later as suitable for a particular
+	 * configuration.
+	 */
+	set_handler(0x180, &except_vec3_generic, 0x80);
+
+	/*
+	 * Setup default vectors
+	 */
+	for (i = 0; i <= 31; i++)
+		set_except_vector(i, handle_reserved);
+
+	/*
+	 * Copy the EJTAG debug exception vector handler code to it's final
+	 * destination.
+	 */
+	if (cpu_has_ejtag && board_ejtag_handler_setup)
+		board_ejtag_handler_setup();
+
+	/*
+	 * Only some CPUs have the watch exceptions.
+	 */
+	if (cpu_has_watch)
+		set_except_vector(EXCCODE_WATCH, handle_watch);
+
+	/*
+	 * Initialise interrupt handlers
+	 */
+	if (cpu_has_veic || cpu_has_vint) {
+		int nvec = cpu_has_veic ? 64 : 8;
+		for (i = 0; i < nvec; i++)
+			set_vi_handler(i, NULL);
+	}
+	else if (cpu_has_divec)
+		set_handler(0x200, &except_vec4, 0x8);
+
+	/*
+	 * Some CPUs can enable/disable for cache parity detection, but does
+	 * it different ways.
+	 */
+	parity_protection_init();
+
+	/*
+	 * The Data Bus Errors / Instruction Bus Errors are signaled
+	 * by external hardware.  Therefore these two exceptions
+	 * may have board specific handlers.
+	 */
+	if (board_be_init)
+		board_be_init();
+
+	set_except_vector(EXCCODE_INT, using_rollback_handler() ?
+					rollback_handle_int : handle_int);
+	set_except_vector(EXCCODE_MOD, handle_tlbm);
+	set_except_vector(EXCCODE_TLBL, handle_tlbl);
+	set_except_vector(EXCCODE_TLBS, handle_tlbs);
+
+	set_except_vector(EXCCODE_ADEL, handle_adel);
+	set_except_vector(EXCCODE_ADES, handle_ades);
+
+	set_except_vector(EXCCODE_IBE, handle_ibe);
+	set_except_vector(EXCCODE_DBE, handle_dbe);
+
+	set_except_vector(EXCCODE_SYS, handle_sys);
+	set_except_vector(EXCCODE_BP, handle_bp);
+
+	if (rdhwr_noopt)
+		set_except_vector(EXCCODE_RI, handle_ri);
+	else {
+		if (cpu_has_vtag_icache)
+			set_except_vector(EXCCODE_RI, handle_ri_rdhwr_tlbp);
+		else if (current_cpu_type() == CPU_LOONGSON64)
+			set_except_vector(EXCCODE_RI, handle_ri_rdhwr_tlbp);
+		else
+			set_except_vector(EXCCODE_RI, handle_ri_rdhwr);
+	}
+
+	set_except_vector(EXCCODE_CPU, handle_cpu);
+	set_except_vector(EXCCODE_OV, handle_ov);
+	set_except_vector(EXCCODE_TR, handle_tr);
+	set_except_vector(EXCCODE_MSAFPE, handle_msa_fpe);
+
+	if (board_nmi_handler_setup)
+		board_nmi_handler_setup();
+
+	if (cpu_has_fpu && !cpu_has_nofpuex)
+		set_except_vector(EXCCODE_FPE, handle_fpe);
+
+	if (cpu_has_ftlbparex)
+		set_except_vector(MIPS_EXCCODE_TLBPAR, handle_ftlb);
+
+	if (cpu_has_gsexcex)
+		set_except_vector(LOONGSON_EXCCODE_GSEXC, handle_gsexc);
+
+	if (cpu_has_rixiex) {
+		set_except_vector(EXCCODE_TLBRI, tlb_do_page_fault_0);
+		set_except_vector(EXCCODE_TLBXI, tlb_do_page_fault_0);
+	}
+
+	set_except_vector(EXCCODE_MSADIS, handle_msa);
+	set_except_vector(EXCCODE_MDMX, handle_mdmx);
+
+	if (cpu_has_mcheck)
+		set_except_vector(EXCCODE_MCHECK, handle_mcheck);
+
+	if (cpu_has_mipsmt)
+		set_except_vector(EXCCODE_THREAD, handle_mt);
+
+	set_except_vector(EXCCODE_DSPDIS, handle_dsp);
+
+	if (board_cache_error_setup)
+		board_cache_error_setup();
+
+	if (cpu_has_vce)
+		/* Special exception: R4[04]00 uses also the divec space. */
+		set_handler(0x180, &except_vec3_r4000, 0x100);
+	else if (cpu_has_4kex)
+		set_handler(0x180, &except_vec3_generic, 0x80);
+	else
+		set_handler(0x080, &except_vec3_generic, 0x80);
+
+	local_flush_icache_range(ebase, ebase + vec_size);
+
+	sort_extable(__start___dbe_table, __stop___dbe_table);
+
+	cu2_notifier(default_cu2_call, 0x80000000);	/* Run last  */
+}
+
+static int trap_pm_notifier(struct notifier_block *self, unsigned long cmd,
+			    void *v)
+{
+	switch (cmd) {
+	case CPU_PM_ENTER_FAILED:
+	case CPU_PM_EXIT:
+		configure_status();
+		configure_hwrena();
+		configure_exception_vector();
+
+		/* Restore register with CPU number for TLB handlers */
+		TLBMISS_HANDLER_RESTORE();
+
+		break;
+	}
+
+	return NOTIFY_OK;
+}
+
+static struct notifier_block trap_pm_notifier_block = {
+	.notifier_call = trap_pm_notifier,
+};
+
+static int __init trap_pm_init(void)
+{
+	return cpu_pm_register_notifier(&trap_pm_notifier_block);
+}
+arch_initcall(trap_pm_init);
diff --git a/arch/mips/kernel/unaligned.c b/arch/mips/kernel/unaligned.c
new file mode 100644
index 000000000..7b5aba5df
--- /dev/null
+++ b/arch/mips/kernel/unaligned.c
@@ -0,0 +1,1572 @@
+/*
+ * Handle unaligned accesses by emulation.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1996, 1998, 1999, 2002 by Ralf Baechle
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ * Copyright (C) 2014 Imagination Technologies Ltd.
+ *
+ * This file contains exception handler for address error exception with the
+ * special capability to execute faulting instructions in software.  The
+ * handler does not try to handle the case when the program counter points
+ * to an address not aligned to a word boundary.
+ *
+ * Putting data to unaligned addresses is a bad practice even on Intel where
+ * only the performance is affected.  Much worse is that such code is non-
+ * portable.  Due to several programs that die on MIPS due to alignment
+ * problems I decided to implement this handler anyway though I originally
+ * didn't intend to do this at all for user code.
+ *
+ * For now I enable fixing of address errors by default to make life easier.
+ * I however intend to disable this somewhen in the future when the alignment
+ * problems with user programs have been fixed.	 For programmers this is the
+ * right way to go.
+ *
+ * Fixing address errors is a per process option.  The option is inherited
+ * across fork(2) and execve(2) calls.	If you really want to use the
+ * option in your user programs - I discourage the use of the software
+ * emulation strongly - use the following code in your userland stuff:
+ *
+ * #include <sys/sysmips.h>
+ *
+ * ...
+ * sysmips(MIPS_FIXADE, x);
+ * ...
+ *
+ * The argument x is 0 for disabling software emulation, enabled otherwise.
+ *
+ * Below a little program to play around with this feature.
+ *
+ * #include <stdio.h>
+ * #include <sys/sysmips.h>
+ *
+ * struct foo {
+ *	   unsigned char bar[8];
+ * };
+ *
+ * main(int argc, char *argv[])
+ * {
+ *	   struct foo x = {0, 1, 2, 3, 4, 5, 6, 7};
+ *	   unsigned int *p = (unsigned int *) (x.bar + 3);
+ *	   int i;
+ *
+ *	   if (argc > 1)
+ *		   sysmips(MIPS_FIXADE, atoi(argv[1]));
+ *
+ *	   printf("*p = %08lx\n", *p);
+ *
+ *	   *p = 0xdeadface;
+ *
+ *	   for(i = 0; i <= 7; i++)
+ *	   printf("%02x ", x.bar[i]);
+ *	   printf("\n");
+ * }
+ *
+ * Coprocessor loads are not supported; I think this case is unimportant
+ * in the practice.
+ *
+ * TODO: Handle ndc (attempted store to doubleword in uncached memory)
+ *	 exception for the R6000.
+ *	 A store crossing a page boundary might be executed only partially.
+ *	 Undo the partial store in this case.
+ */
+#include <linux/context_tracking.h>
+#include <linux/mm.h>
+#include <linux/signal.h>
+#include <linux/smp.h>
+#include <linux/sched.h>
+#include <linux/debugfs.h>
+#include <linux/perf_event.h>
+
+#include <asm/asm.h>
+#include <asm/branch.h>
+#include <asm/byteorder.h>
+#include <asm/cop2.h>
+#include <asm/debug.h>
+#include <asm/fpu.h>
+#include <asm/fpu_emulator.h>
+#include <asm/inst.h>
+#include <asm/unaligned-emul.h>
+#include <asm/mmu_context.h>
+#include <linux/uaccess.h>
+
+#include "access-helper.h"
+
+enum {
+	UNALIGNED_ACTION_QUIET,
+	UNALIGNED_ACTION_SIGNAL,
+	UNALIGNED_ACTION_SHOW,
+};
+#ifdef CONFIG_DEBUG_FS
+static u32 unaligned_instructions;
+static u32 unaligned_action;
+#else
+#define unaligned_action UNALIGNED_ACTION_QUIET
+#endif
+extern void show_registers(struct pt_regs *regs);
+
+static void emulate_load_store_insn(struct pt_regs *regs,
+	void __user *addr, unsigned int *pc)
+{
+	unsigned long origpc, orig31, value;
+	union mips_instruction insn;
+	unsigned int res;
+	bool user = user_mode(regs);
+
+	origpc = (unsigned long)pc;
+	orig31 = regs->regs[31];
+
+	perf_sw_event(PERF_COUNT_SW_EMULATION_FAULTS, 1, regs, 0);
+
+	/*
+	 * This load never faults.
+	 */
+	__get_inst32(&insn.word, pc, user);
+
+	switch (insn.i_format.opcode) {
+		/*
+		 * These are instructions that a compiler doesn't generate.  We
+		 * can assume therefore that the code is MIPS-aware and
+		 * really buggy.  Emulating these instructions would break the
+		 * semantics anyway.
+		 */
+	case ll_op:
+	case lld_op:
+	case sc_op:
+	case scd_op:
+
+		/*
+		 * For these instructions the only way to create an address
+		 * error is an attempted access to kernel/supervisor address
+		 * space.
+		 */
+	case ldl_op:
+	case ldr_op:
+	case lwl_op:
+	case lwr_op:
+	case sdl_op:
+	case sdr_op:
+	case swl_op:
+	case swr_op:
+	case lb_op:
+	case lbu_op:
+	case sb_op:
+		goto sigbus;
+
+		/*
+		 * The remaining opcodes are the ones that are really of
+		 * interest.
+		 */
+	case spec3_op:
+		if (insn.dsp_format.func == lx_op) {
+			switch (insn.dsp_format.op) {
+			case lwx_op:
+				if (user && !access_ok(addr, 4))
+					goto sigbus;
+				LoadW(addr, value, res);
+				if (res)
+					goto fault;
+				compute_return_epc(regs);
+				regs->regs[insn.dsp_format.rd] = value;
+				break;
+			case lhx_op:
+				if (user && !access_ok(addr, 2))
+					goto sigbus;
+				LoadHW(addr, value, res);
+				if (res)
+					goto fault;
+				compute_return_epc(regs);
+				regs->regs[insn.dsp_format.rd] = value;
+				break;
+			default:
+				goto sigill;
+			}
+		}
+#ifdef CONFIG_EVA
+		else {
+			/*
+			 * we can land here only from kernel accessing user
+			 * memory, so we need to "switch" the address limit to
+			 * user space, so that address check can work properly.
+			 */
+			switch (insn.spec3_format.func) {
+			case lhe_op:
+				if (!access_ok(addr, 2))
+					goto sigbus;
+				LoadHWE(addr, value, res);
+				if (res)
+					goto fault;
+				compute_return_epc(regs);
+				regs->regs[insn.spec3_format.rt] = value;
+				break;
+			case lwe_op:
+				if (!access_ok(addr, 4))
+					goto sigbus;
+				LoadWE(addr, value, res);
+				if (res)
+					goto fault;
+				compute_return_epc(regs);
+				regs->regs[insn.spec3_format.rt] = value;
+				break;
+			case lhue_op:
+				if (!access_ok(addr, 2))
+					goto sigbus;
+				LoadHWUE(addr, value, res);
+				if (res)
+					goto fault;
+				compute_return_epc(regs);
+				regs->regs[insn.spec3_format.rt] = value;
+				break;
+			case she_op:
+				if (!access_ok(addr, 2))
+					goto sigbus;
+				compute_return_epc(regs);
+				value = regs->regs[insn.spec3_format.rt];
+				StoreHWE(addr, value, res);
+				if (res)
+					goto fault;
+				break;
+			case swe_op:
+				if (!access_ok(addr, 4))
+					goto sigbus;
+				compute_return_epc(regs);
+				value = regs->regs[insn.spec3_format.rt];
+				StoreWE(addr, value, res);
+				if (res)
+					goto fault;
+				break;
+			default:
+				goto sigill;
+			}
+		}
+#endif
+		break;
+	case lh_op:
+		if (user && !access_ok(addr, 2))
+			goto sigbus;
+
+		if (IS_ENABLED(CONFIG_EVA) && user)
+			LoadHWE(addr, value, res);
+		else
+			LoadHW(addr, value, res);
+
+		if (res)
+			goto fault;
+		compute_return_epc(regs);
+		regs->regs[insn.i_format.rt] = value;
+		break;
+
+	case lw_op:
+		if (user && !access_ok(addr, 4))
+			goto sigbus;
+
+		if (IS_ENABLED(CONFIG_EVA) && user)
+			LoadWE(addr, value, res);
+		else
+			LoadW(addr, value, res);
+
+		if (res)
+			goto fault;
+		compute_return_epc(regs);
+		regs->regs[insn.i_format.rt] = value;
+		break;
+
+	case lhu_op:
+		if (user && !access_ok(addr, 2))
+			goto sigbus;
+
+		if (IS_ENABLED(CONFIG_EVA) && user)
+			LoadHWUE(addr, value, res);
+		else
+			LoadHWU(addr, value, res);
+
+		if (res)
+			goto fault;
+		compute_return_epc(regs);
+		regs->regs[insn.i_format.rt] = value;
+		break;
+
+	case lwu_op:
+#ifdef CONFIG_64BIT
+		/*
+		 * A 32-bit kernel might be running on a 64-bit processor.  But
+		 * if we're on a 32-bit processor and an i-cache incoherency
+		 * or race makes us see a 64-bit instruction here the sdl/sdr
+		 * would blow up, so for now we don't handle unaligned 64-bit
+		 * instructions on 32-bit kernels.
+		 */
+		if (user && !access_ok(addr, 4))
+			goto sigbus;
+
+		LoadWU(addr, value, res);
+		if (res)
+			goto fault;
+		compute_return_epc(regs);
+		regs->regs[insn.i_format.rt] = value;
+		break;
+#endif /* CONFIG_64BIT */
+
+		/* Cannot handle 64-bit instructions in 32-bit kernel */
+		goto sigill;
+
+	case ld_op:
+#ifdef CONFIG_64BIT
+		/*
+		 * A 32-bit kernel might be running on a 64-bit processor.  But
+		 * if we're on a 32-bit processor and an i-cache incoherency
+		 * or race makes us see a 64-bit instruction here the sdl/sdr
+		 * would blow up, so for now we don't handle unaligned 64-bit
+		 * instructions on 32-bit kernels.
+		 */
+		if (user && !access_ok(addr, 8))
+			goto sigbus;
+
+		LoadDW(addr, value, res);
+		if (res)
+			goto fault;
+		compute_return_epc(regs);
+		regs->regs[insn.i_format.rt] = value;
+		break;
+#endif /* CONFIG_64BIT */
+
+		/* Cannot handle 64-bit instructions in 32-bit kernel */
+		goto sigill;
+
+	case sh_op:
+		if (user && !access_ok(addr, 2))
+			goto sigbus;
+
+		compute_return_epc(regs);
+		value = regs->regs[insn.i_format.rt];
+
+		if (IS_ENABLED(CONFIG_EVA) && user)
+			StoreHWE(addr, value, res);
+		else
+			StoreHW(addr, value, res);
+
+		if (res)
+			goto fault;
+		break;
+
+	case sw_op:
+		if (user && !access_ok(addr, 4))
+			goto sigbus;
+
+		compute_return_epc(regs);
+		value = regs->regs[insn.i_format.rt];
+
+		if (IS_ENABLED(CONFIG_EVA) && user)
+			StoreWE(addr, value, res);
+		else
+			StoreW(addr, value, res);
+
+		if (res)
+			goto fault;
+		break;
+
+	case sd_op:
+#ifdef CONFIG_64BIT
+		/*
+		 * A 32-bit kernel might be running on a 64-bit processor.  But
+		 * if we're on a 32-bit processor and an i-cache incoherency
+		 * or race makes us see a 64-bit instruction here the sdl/sdr
+		 * would blow up, so for now we don't handle unaligned 64-bit
+		 * instructions on 32-bit kernels.
+		 */
+		if (user && !access_ok(addr, 8))
+			goto sigbus;
+
+		compute_return_epc(regs);
+		value = regs->regs[insn.i_format.rt];
+		StoreDW(addr, value, res);
+		if (res)
+			goto fault;
+		break;
+#endif /* CONFIG_64BIT */
+
+		/* Cannot handle 64-bit instructions in 32-bit kernel */
+		goto sigill;
+
+#ifdef CONFIG_MIPS_FP_SUPPORT
+
+	case lwc1_op:
+	case ldc1_op:
+	case swc1_op:
+	case sdc1_op:
+	case cop1x_op: {
+		void __user *fault_addr = NULL;
+
+		die_if_kernel("Unaligned FP access in kernel code", regs);
+		BUG_ON(!used_math());
+
+		res = fpu_emulator_cop1Handler(regs, &current->thread.fpu, 1,
+					       &fault_addr);
+		own_fpu(1);	/* Restore FPU state. */
+
+		/* Signal if something went wrong. */
+		process_fpemu_return(res, fault_addr, 0);
+
+		if (res == 0)
+			break;
+		return;
+	}
+#endif /* CONFIG_MIPS_FP_SUPPORT */
+
+#ifdef CONFIG_CPU_HAS_MSA
+
+	case msa_op: {
+		unsigned int wd, preempted;
+		enum msa_2b_fmt df;
+		union fpureg *fpr;
+
+		if (!cpu_has_msa)
+			goto sigill;
+
+		/*
+		 * If we've reached this point then userland should have taken
+		 * the MSA disabled exception & initialised vector context at
+		 * some point in the past.
+		 */
+		BUG_ON(!thread_msa_context_live());
+
+		df = insn.msa_mi10_format.df;
+		wd = insn.msa_mi10_format.wd;
+		fpr = &current->thread.fpu.fpr[wd];
+
+		switch (insn.msa_mi10_format.func) {
+		case msa_ld_op:
+			if (!access_ok(addr, sizeof(*fpr)))
+				goto sigbus;
+
+			do {
+				/*
+				 * If we have live MSA context keep track of
+				 * whether we get preempted in order to avoid
+				 * the register context we load being clobbered
+				 * by the live context as it's saved during
+				 * preemption. If we don't have live context
+				 * then it can't be saved to clobber the value
+				 * we load.
+				 */
+				preempted = test_thread_flag(TIF_USEDMSA);
+
+				res = __copy_from_user_inatomic(fpr, addr,
+								sizeof(*fpr));
+				if (res)
+					goto fault;
+
+				/*
+				 * Update the hardware register if it is in use
+				 * by the task in this quantum, in order to
+				 * avoid having to save & restore the whole
+				 * vector context.
+				 */
+				preempt_disable();
+				if (test_thread_flag(TIF_USEDMSA)) {
+					write_msa_wr(wd, fpr, df);
+					preempted = 0;
+				}
+				preempt_enable();
+			} while (preempted);
+			break;
+
+		case msa_st_op:
+			if (!access_ok(addr, sizeof(*fpr)))
+				goto sigbus;
+
+			/*
+			 * Update from the hardware register if it is in use by
+			 * the task in this quantum, in order to avoid having to
+			 * save & restore the whole vector context.
+			 */
+			preempt_disable();
+			if (test_thread_flag(TIF_USEDMSA))
+				read_msa_wr(wd, fpr, df);
+			preempt_enable();
+
+			res = __copy_to_user_inatomic(addr, fpr, sizeof(*fpr));
+			if (res)
+				goto fault;
+			break;
+
+		default:
+			goto sigbus;
+		}
+
+		compute_return_epc(regs);
+		break;
+	}
+#endif /* CONFIG_CPU_HAS_MSA */
+
+#ifndef CONFIG_CPU_MIPSR6
+	/*
+	 * COP2 is available to implementor for application specific use.
+	 * It's up to applications to register a notifier chain and do
+	 * whatever they have to do, including possible sending of signals.
+	 *
+	 * This instruction has been reallocated in Release 6
+	 */
+	case lwc2_op:
+		cu2_notifier_call_chain(CU2_LWC2_OP, regs);
+		break;
+
+	case ldc2_op:
+		cu2_notifier_call_chain(CU2_LDC2_OP, regs);
+		break;
+
+	case swc2_op:
+		cu2_notifier_call_chain(CU2_SWC2_OP, regs);
+		break;
+
+	case sdc2_op:
+		cu2_notifier_call_chain(CU2_SDC2_OP, regs);
+		break;
+#endif
+	default:
+		/*
+		 * Pheeee...  We encountered an yet unknown instruction or
+		 * cache coherence problem.  Die sucker, die ...
+		 */
+		goto sigill;
+	}
+
+#ifdef CONFIG_DEBUG_FS
+	unaligned_instructions++;
+#endif
+
+	return;
+
+fault:
+	/* roll back jump/branch */
+	regs->cp0_epc = origpc;
+	regs->regs[31] = orig31;
+	/* Did we have an exception handler installed? */
+	if (fixup_exception(regs))
+		return;
+
+	die_if_kernel("Unhandled kernel unaligned access", regs);
+	force_sig(SIGSEGV);
+
+	return;
+
+sigbus:
+	die_if_kernel("Unhandled kernel unaligned access", regs);
+	force_sig(SIGBUS);
+
+	return;
+
+sigill:
+	die_if_kernel
+	    ("Unhandled kernel unaligned access or invalid instruction", regs);
+	force_sig(SIGILL);
+}
+
+/* Recode table from 16-bit register notation to 32-bit GPR. */
+const int reg16to32[] = { 16, 17, 2, 3, 4, 5, 6, 7 };
+
+/* Recode table from 16-bit STORE register notation to 32-bit GPR. */
+static const int reg16to32st[] = { 0, 17, 2, 3, 4, 5, 6, 7 };
+
+static void emulate_load_store_microMIPS(struct pt_regs *regs,
+					 void __user *addr)
+{
+	unsigned long value;
+	unsigned int res;
+	int i;
+	unsigned int reg = 0, rvar;
+	unsigned long orig31;
+	u16 __user *pc16;
+	u16 halfword;
+	unsigned int word;
+	unsigned long origpc, contpc;
+	union mips_instruction insn;
+	struct mm_decoded_insn mminsn;
+	bool user = user_mode(regs);
+
+	origpc = regs->cp0_epc;
+	orig31 = regs->regs[31];
+
+	mminsn.micro_mips_mode = 1;
+
+	/*
+	 * This load never faults.
+	 */
+	pc16 = (unsigned short __user *)msk_isa16_mode(regs->cp0_epc);
+	__get_user(halfword, pc16);
+	pc16++;
+	contpc = regs->cp0_epc + 2;
+	word = ((unsigned int)halfword << 16);
+	mminsn.pc_inc = 2;
+
+	if (!mm_insn_16bit(halfword)) {
+		__get_user(halfword, pc16);
+		pc16++;
+		contpc = regs->cp0_epc + 4;
+		mminsn.pc_inc = 4;
+		word |= halfword;
+	}
+	mminsn.insn = word;
+
+	if (get_user(halfword, pc16))
+		goto fault;
+	mminsn.next_pc_inc = 2;
+	word = ((unsigned int)halfword << 16);
+
+	if (!mm_insn_16bit(halfword)) {
+		pc16++;
+		if (get_user(halfword, pc16))
+			goto fault;
+		mminsn.next_pc_inc = 4;
+		word |= halfword;
+	}
+	mminsn.next_insn = word;
+
+	insn = (union mips_instruction)(mminsn.insn);
+	if (mm_isBranchInstr(regs, mminsn, &contpc))
+		insn = (union mips_instruction)(mminsn.next_insn);
+
+	/*  Parse instruction to find what to do */
+
+	switch (insn.mm_i_format.opcode) {
+
+	case mm_pool32a_op:
+		switch (insn.mm_x_format.func) {
+		case mm_lwxs_op:
+			reg = insn.mm_x_format.rd;
+			goto loadW;
+		}
+
+		goto sigbus;
+
+	case mm_pool32b_op:
+		switch (insn.mm_m_format.func) {
+		case mm_lwp_func:
+			reg = insn.mm_m_format.rd;
+			if (reg == 31)
+				goto sigbus;
+
+			if (user && !access_ok(addr, 8))
+				goto sigbus;
+
+			LoadW(addr, value, res);
+			if (res)
+				goto fault;
+			regs->regs[reg] = value;
+			addr += 4;
+			LoadW(addr, value, res);
+			if (res)
+				goto fault;
+			regs->regs[reg + 1] = value;
+			goto success;
+
+		case mm_swp_func:
+			reg = insn.mm_m_format.rd;
+			if (reg == 31)
+				goto sigbus;
+
+			if (user && !access_ok(addr, 8))
+				goto sigbus;
+
+			value = regs->regs[reg];
+			StoreW(addr, value, res);
+			if (res)
+				goto fault;
+			addr += 4;
+			value = regs->regs[reg + 1];
+			StoreW(addr, value, res);
+			if (res)
+				goto fault;
+			goto success;
+
+		case mm_ldp_func:
+#ifdef CONFIG_64BIT
+			reg = insn.mm_m_format.rd;
+			if (reg == 31)
+				goto sigbus;
+
+			if (user && !access_ok(addr, 16))
+				goto sigbus;
+
+			LoadDW(addr, value, res);
+			if (res)
+				goto fault;
+			regs->regs[reg] = value;
+			addr += 8;
+			LoadDW(addr, value, res);
+			if (res)
+				goto fault;
+			regs->regs[reg + 1] = value;
+			goto success;
+#endif /* CONFIG_64BIT */
+
+			goto sigill;
+
+		case mm_sdp_func:
+#ifdef CONFIG_64BIT
+			reg = insn.mm_m_format.rd;
+			if (reg == 31)
+				goto sigbus;
+
+			if (user && !access_ok(addr, 16))
+				goto sigbus;
+
+			value = regs->regs[reg];
+			StoreDW(addr, value, res);
+			if (res)
+				goto fault;
+			addr += 8;
+			value = regs->regs[reg + 1];
+			StoreDW(addr, value, res);
+			if (res)
+				goto fault;
+			goto success;
+#endif /* CONFIG_64BIT */
+
+			goto sigill;
+
+		case mm_lwm32_func:
+			reg = insn.mm_m_format.rd;
+			rvar = reg & 0xf;
+			if ((rvar > 9) || !reg)
+				goto sigill;
+			if (reg & 0x10) {
+				if (user && !access_ok(addr, 4 * (rvar + 1)))
+					goto sigbus;
+			} else {
+				if (user && !access_ok(addr, 4 * rvar))
+					goto sigbus;
+			}
+			if (rvar == 9)
+				rvar = 8;
+			for (i = 16; rvar; rvar--, i++) {
+				LoadW(addr, value, res);
+				if (res)
+					goto fault;
+				addr += 4;
+				regs->regs[i] = value;
+			}
+			if ((reg & 0xf) == 9) {
+				LoadW(addr, value, res);
+				if (res)
+					goto fault;
+				addr += 4;
+				regs->regs[30] = value;
+			}
+			if (reg & 0x10) {
+				LoadW(addr, value, res);
+				if (res)
+					goto fault;
+				regs->regs[31] = value;
+			}
+			goto success;
+
+		case mm_swm32_func:
+			reg = insn.mm_m_format.rd;
+			rvar = reg & 0xf;
+			if ((rvar > 9) || !reg)
+				goto sigill;
+			if (reg & 0x10) {
+				if (user && !access_ok(addr, 4 * (rvar + 1)))
+					goto sigbus;
+			} else {
+				if (user && !access_ok(addr, 4 * rvar))
+					goto sigbus;
+			}
+			if (rvar == 9)
+				rvar = 8;
+			for (i = 16; rvar; rvar--, i++) {
+				value = regs->regs[i];
+				StoreW(addr, value, res);
+				if (res)
+					goto fault;
+				addr += 4;
+			}
+			if ((reg & 0xf) == 9) {
+				value = regs->regs[30];
+				StoreW(addr, value, res);
+				if (res)
+					goto fault;
+				addr += 4;
+			}
+			if (reg & 0x10) {
+				value = regs->regs[31];
+				StoreW(addr, value, res);
+				if (res)
+					goto fault;
+			}
+			goto success;
+
+		case mm_ldm_func:
+#ifdef CONFIG_64BIT
+			reg = insn.mm_m_format.rd;
+			rvar = reg & 0xf;
+			if ((rvar > 9) || !reg)
+				goto sigill;
+			if (reg & 0x10) {
+				if (user && !access_ok(addr, 8 * (rvar + 1)))
+					goto sigbus;
+			} else {
+				if (user && !access_ok(addr, 8 * rvar))
+					goto sigbus;
+			}
+			if (rvar == 9)
+				rvar = 8;
+
+			for (i = 16; rvar; rvar--, i++) {
+				LoadDW(addr, value, res);
+				if (res)
+					goto fault;
+				addr += 4;
+				regs->regs[i] = value;
+			}
+			if ((reg & 0xf) == 9) {
+				LoadDW(addr, value, res);
+				if (res)
+					goto fault;
+				addr += 8;
+				regs->regs[30] = value;
+			}
+			if (reg & 0x10) {
+				LoadDW(addr, value, res);
+				if (res)
+					goto fault;
+				regs->regs[31] = value;
+			}
+			goto success;
+#endif /* CONFIG_64BIT */
+
+			goto sigill;
+
+		case mm_sdm_func:
+#ifdef CONFIG_64BIT
+			reg = insn.mm_m_format.rd;
+			rvar = reg & 0xf;
+			if ((rvar > 9) || !reg)
+				goto sigill;
+			if (reg & 0x10) {
+				if (user && !access_ok(addr, 8 * (rvar + 1)))
+					goto sigbus;
+			} else {
+				if (user && !access_ok(addr, 8 * rvar))
+					goto sigbus;
+			}
+			if (rvar == 9)
+				rvar = 8;
+
+			for (i = 16; rvar; rvar--, i++) {
+				value = regs->regs[i];
+				StoreDW(addr, value, res);
+				if (res)
+					goto fault;
+				addr += 8;
+			}
+			if ((reg & 0xf) == 9) {
+				value = regs->regs[30];
+				StoreDW(addr, value, res);
+				if (res)
+					goto fault;
+				addr += 8;
+			}
+			if (reg & 0x10) {
+				value = regs->regs[31];
+				StoreDW(addr, value, res);
+				if (res)
+					goto fault;
+			}
+			goto success;
+#endif /* CONFIG_64BIT */
+
+			goto sigill;
+
+			/*  LWC2, SWC2, LDC2, SDC2 are not serviced */
+		}
+
+		goto sigbus;
+
+	case mm_pool32c_op:
+		switch (insn.mm_m_format.func) {
+		case mm_lwu_func:
+			reg = insn.mm_m_format.rd;
+			goto loadWU;
+		}
+
+		/*  LL,SC,LLD,SCD are not serviced */
+		goto sigbus;
+
+#ifdef CONFIG_MIPS_FP_SUPPORT
+	case mm_pool32f_op:
+		switch (insn.mm_x_format.func) {
+		case mm_lwxc1_func:
+		case mm_swxc1_func:
+		case mm_ldxc1_func:
+		case mm_sdxc1_func:
+			goto fpu_emul;
+		}
+
+		goto sigbus;
+
+	case mm_ldc132_op:
+	case mm_sdc132_op:
+	case mm_lwc132_op:
+	case mm_swc132_op: {
+		void __user *fault_addr = NULL;
+
+fpu_emul:
+		/* roll back jump/branch */
+		regs->cp0_epc = origpc;
+		regs->regs[31] = orig31;
+
+		die_if_kernel("Unaligned FP access in kernel code", regs);
+		BUG_ON(!used_math());
+		BUG_ON(!is_fpu_owner());
+
+		res = fpu_emulator_cop1Handler(regs, &current->thread.fpu, 1,
+					       &fault_addr);
+		own_fpu(1);	/* restore FPU state */
+
+		/* If something went wrong, signal */
+		process_fpemu_return(res, fault_addr, 0);
+
+		if (res == 0)
+			goto success;
+		return;
+	}
+#endif /* CONFIG_MIPS_FP_SUPPORT */
+
+	case mm_lh32_op:
+		reg = insn.mm_i_format.rt;
+		goto loadHW;
+
+	case mm_lhu32_op:
+		reg = insn.mm_i_format.rt;
+		goto loadHWU;
+
+	case mm_lw32_op:
+		reg = insn.mm_i_format.rt;
+		goto loadW;
+
+	case mm_sh32_op:
+		reg = insn.mm_i_format.rt;
+		goto storeHW;
+
+	case mm_sw32_op:
+		reg = insn.mm_i_format.rt;
+		goto storeW;
+
+	case mm_ld32_op:
+		reg = insn.mm_i_format.rt;
+		goto loadDW;
+
+	case mm_sd32_op:
+		reg = insn.mm_i_format.rt;
+		goto storeDW;
+
+	case mm_pool16c_op:
+		switch (insn.mm16_m_format.func) {
+		case mm_lwm16_op:
+			reg = insn.mm16_m_format.rlist;
+			rvar = reg + 1;
+			if (user && !access_ok(addr, 4 * rvar))
+				goto sigbus;
+
+			for (i = 16; rvar; rvar--, i++) {
+				LoadW(addr, value, res);
+				if (res)
+					goto fault;
+				addr += 4;
+				regs->regs[i] = value;
+			}
+			LoadW(addr, value, res);
+			if (res)
+				goto fault;
+			regs->regs[31] = value;
+
+			goto success;
+
+		case mm_swm16_op:
+			reg = insn.mm16_m_format.rlist;
+			rvar = reg + 1;
+			if (user && !access_ok(addr, 4 * rvar))
+				goto sigbus;
+
+			for (i = 16; rvar; rvar--, i++) {
+				value = regs->regs[i];
+				StoreW(addr, value, res);
+				if (res)
+					goto fault;
+				addr += 4;
+			}
+			value = regs->regs[31];
+			StoreW(addr, value, res);
+			if (res)
+				goto fault;
+
+			goto success;
+
+		}
+
+		goto sigbus;
+
+	case mm_lhu16_op:
+		reg = reg16to32[insn.mm16_rb_format.rt];
+		goto loadHWU;
+
+	case mm_lw16_op:
+		reg = reg16to32[insn.mm16_rb_format.rt];
+		goto loadW;
+
+	case mm_sh16_op:
+		reg = reg16to32st[insn.mm16_rb_format.rt];
+		goto storeHW;
+
+	case mm_sw16_op:
+		reg = reg16to32st[insn.mm16_rb_format.rt];
+		goto storeW;
+
+	case mm_lwsp16_op:
+		reg = insn.mm16_r5_format.rt;
+		goto loadW;
+
+	case mm_swsp16_op:
+		reg = insn.mm16_r5_format.rt;
+		goto storeW;
+
+	case mm_lwgp16_op:
+		reg = reg16to32[insn.mm16_r3_format.rt];
+		goto loadW;
+
+	default:
+		goto sigill;
+	}
+
+loadHW:
+	if (user && !access_ok(addr, 2))
+		goto sigbus;
+
+	LoadHW(addr, value, res);
+	if (res)
+		goto fault;
+	regs->regs[reg] = value;
+	goto success;
+
+loadHWU:
+	if (user && !access_ok(addr, 2))
+		goto sigbus;
+
+	LoadHWU(addr, value, res);
+	if (res)
+		goto fault;
+	regs->regs[reg] = value;
+	goto success;
+
+loadW:
+	if (user && !access_ok(addr, 4))
+		goto sigbus;
+
+	LoadW(addr, value, res);
+	if (res)
+		goto fault;
+	regs->regs[reg] = value;
+	goto success;
+
+loadWU:
+#ifdef CONFIG_64BIT
+	/*
+	 * A 32-bit kernel might be running on a 64-bit processor.  But
+	 * if we're on a 32-bit processor and an i-cache incoherency
+	 * or race makes us see a 64-bit instruction here the sdl/sdr
+	 * would blow up, so for now we don't handle unaligned 64-bit
+	 * instructions on 32-bit kernels.
+	 */
+	if (user && !access_ok(addr, 4))
+		goto sigbus;
+
+	LoadWU(addr, value, res);
+	if (res)
+		goto fault;
+	regs->regs[reg] = value;
+	goto success;
+#endif /* CONFIG_64BIT */
+
+	/* Cannot handle 64-bit instructions in 32-bit kernel */
+	goto sigill;
+
+loadDW:
+#ifdef CONFIG_64BIT
+	/*
+	 * A 32-bit kernel might be running on a 64-bit processor.  But
+	 * if we're on a 32-bit processor and an i-cache incoherency
+	 * or race makes us see a 64-bit instruction here the sdl/sdr
+	 * would blow up, so for now we don't handle unaligned 64-bit
+	 * instructions on 32-bit kernels.
+	 */
+	if (user && !access_ok(addr, 8))
+		goto sigbus;
+
+	LoadDW(addr, value, res);
+	if (res)
+		goto fault;
+	regs->regs[reg] = value;
+	goto success;
+#endif /* CONFIG_64BIT */
+
+	/* Cannot handle 64-bit instructions in 32-bit kernel */
+	goto sigill;
+
+storeHW:
+	if (user && !access_ok(addr, 2))
+		goto sigbus;
+
+	value = regs->regs[reg];
+	StoreHW(addr, value, res);
+	if (res)
+		goto fault;
+	goto success;
+
+storeW:
+	if (user && !access_ok(addr, 4))
+		goto sigbus;
+
+	value = regs->regs[reg];
+	StoreW(addr, value, res);
+	if (res)
+		goto fault;
+	goto success;
+
+storeDW:
+#ifdef CONFIG_64BIT
+	/*
+	 * A 32-bit kernel might be running on a 64-bit processor.  But
+	 * if we're on a 32-bit processor and an i-cache incoherency
+	 * or race makes us see a 64-bit instruction here the sdl/sdr
+	 * would blow up, so for now we don't handle unaligned 64-bit
+	 * instructions on 32-bit kernels.
+	 */
+	if (user && !access_ok(addr, 8))
+		goto sigbus;
+
+	value = regs->regs[reg];
+	StoreDW(addr, value, res);
+	if (res)
+		goto fault;
+	goto success;
+#endif /* CONFIG_64BIT */
+
+	/* Cannot handle 64-bit instructions in 32-bit kernel */
+	goto sigill;
+
+success:
+	regs->cp0_epc = contpc;	/* advance or branch */
+
+#ifdef CONFIG_DEBUG_FS
+	unaligned_instructions++;
+#endif
+	return;
+
+fault:
+	/* roll back jump/branch */
+	regs->cp0_epc = origpc;
+	regs->regs[31] = orig31;
+	/* Did we have an exception handler installed? */
+	if (fixup_exception(regs))
+		return;
+
+	die_if_kernel("Unhandled kernel unaligned access", regs);
+	force_sig(SIGSEGV);
+
+	return;
+
+sigbus:
+	die_if_kernel("Unhandled kernel unaligned access", regs);
+	force_sig(SIGBUS);
+
+	return;
+
+sigill:
+	die_if_kernel
+	    ("Unhandled kernel unaligned access or invalid instruction", regs);
+	force_sig(SIGILL);
+}
+
+static void emulate_load_store_MIPS16e(struct pt_regs *regs, void __user * addr)
+{
+	unsigned long value;
+	unsigned int res;
+	int reg;
+	unsigned long orig31;
+	u16 __user *pc16;
+	unsigned long origpc;
+	union mips16e_instruction mips16inst, oldinst;
+	unsigned int opcode;
+	int extended = 0;
+	bool user = user_mode(regs);
+
+	origpc = regs->cp0_epc;
+	orig31 = regs->regs[31];
+	pc16 = (unsigned short __user *)msk_isa16_mode(origpc);
+	/*
+	 * This load never faults.
+	 */
+	__get_user(mips16inst.full, pc16);
+	oldinst = mips16inst;
+
+	/* skip EXTEND instruction */
+	if (mips16inst.ri.opcode == MIPS16e_extend_op) {
+		extended = 1;
+		pc16++;
+		__get_user(mips16inst.full, pc16);
+	} else if (delay_slot(regs)) {
+		/*  skip jump instructions */
+		/*  JAL/JALX are 32 bits but have OPCODE in first short int */
+		if (mips16inst.ri.opcode == MIPS16e_jal_op)
+			pc16++;
+		pc16++;
+		if (get_user(mips16inst.full, pc16))
+			goto sigbus;
+	}
+
+	opcode = mips16inst.ri.opcode;
+	switch (opcode) {
+	case MIPS16e_i64_op:	/* I64 or RI64 instruction */
+		switch (mips16inst.i64.func) {	/* I64/RI64 func field check */
+		case MIPS16e_ldpc_func:
+		case MIPS16e_ldsp_func:
+			reg = reg16to32[mips16inst.ri64.ry];
+			goto loadDW;
+
+		case MIPS16e_sdsp_func:
+			reg = reg16to32[mips16inst.ri64.ry];
+			goto writeDW;
+
+		case MIPS16e_sdrasp_func:
+			reg = 29;	/* GPRSP */
+			goto writeDW;
+		}
+
+		goto sigbus;
+
+	case MIPS16e_swsp_op:
+		reg = reg16to32[mips16inst.ri.rx];
+		if (extended && cpu_has_mips16e2)
+			switch (mips16inst.ri.imm >> 5) {
+			case 0:		/* SWSP */
+			case 1:		/* SWGP */
+				break;
+			case 2:		/* SHGP */
+				opcode = MIPS16e_sh_op;
+				break;
+			default:
+				goto sigbus;
+			}
+		break;
+
+	case MIPS16e_lwpc_op:
+		reg = reg16to32[mips16inst.ri.rx];
+		break;
+
+	case MIPS16e_lwsp_op:
+		reg = reg16to32[mips16inst.ri.rx];
+		if (extended && cpu_has_mips16e2)
+			switch (mips16inst.ri.imm >> 5) {
+			case 0:		/* LWSP */
+			case 1:		/* LWGP */
+				break;
+			case 2:		/* LHGP */
+				opcode = MIPS16e_lh_op;
+				break;
+			case 4:		/* LHUGP */
+				opcode = MIPS16e_lhu_op;
+				break;
+			default:
+				goto sigbus;
+			}
+		break;
+
+	case MIPS16e_i8_op:
+		if (mips16inst.i8.func != MIPS16e_swrasp_func)
+			goto sigbus;
+		reg = 29;	/* GPRSP */
+		break;
+
+	default:
+		reg = reg16to32[mips16inst.rri.ry];
+		break;
+	}
+
+	switch (opcode) {
+
+	case MIPS16e_lb_op:
+	case MIPS16e_lbu_op:
+	case MIPS16e_sb_op:
+		goto sigbus;
+
+	case MIPS16e_lh_op:
+		if (user && !access_ok(addr, 2))
+			goto sigbus;
+
+		LoadHW(addr, value, res);
+		if (res)
+			goto fault;
+		MIPS16e_compute_return_epc(regs, &oldinst);
+		regs->regs[reg] = value;
+		break;
+
+	case MIPS16e_lhu_op:
+		if (user && !access_ok(addr, 2))
+			goto sigbus;
+
+		LoadHWU(addr, value, res);
+		if (res)
+			goto fault;
+		MIPS16e_compute_return_epc(regs, &oldinst);
+		regs->regs[reg] = value;
+		break;
+
+	case MIPS16e_lw_op:
+	case MIPS16e_lwpc_op:
+	case MIPS16e_lwsp_op:
+		if (user && !access_ok(addr, 4))
+			goto sigbus;
+
+		LoadW(addr, value, res);
+		if (res)
+			goto fault;
+		MIPS16e_compute_return_epc(regs, &oldinst);
+		regs->regs[reg] = value;
+		break;
+
+	case MIPS16e_lwu_op:
+#ifdef CONFIG_64BIT
+		/*
+		 * A 32-bit kernel might be running on a 64-bit processor.  But
+		 * if we're on a 32-bit processor and an i-cache incoherency
+		 * or race makes us see a 64-bit instruction here the sdl/sdr
+		 * would blow up, so for now we don't handle unaligned 64-bit
+		 * instructions on 32-bit kernels.
+		 */
+		if (user && !access_ok(addr, 4))
+			goto sigbus;
+
+		LoadWU(addr, value, res);
+		if (res)
+			goto fault;
+		MIPS16e_compute_return_epc(regs, &oldinst);
+		regs->regs[reg] = value;
+		break;
+#endif /* CONFIG_64BIT */
+
+		/* Cannot handle 64-bit instructions in 32-bit kernel */
+		goto sigill;
+
+	case MIPS16e_ld_op:
+loadDW:
+#ifdef CONFIG_64BIT
+		/*
+		 * A 32-bit kernel might be running on a 64-bit processor.  But
+		 * if we're on a 32-bit processor and an i-cache incoherency
+		 * or race makes us see a 64-bit instruction here the sdl/sdr
+		 * would blow up, so for now we don't handle unaligned 64-bit
+		 * instructions on 32-bit kernels.
+		 */
+		if (user && !access_ok(addr, 8))
+			goto sigbus;
+
+		LoadDW(addr, value, res);
+		if (res)
+			goto fault;
+		MIPS16e_compute_return_epc(regs, &oldinst);
+		regs->regs[reg] = value;
+		break;
+#endif /* CONFIG_64BIT */
+
+		/* Cannot handle 64-bit instructions in 32-bit kernel */
+		goto sigill;
+
+	case MIPS16e_sh_op:
+		if (user && !access_ok(addr, 2))
+			goto sigbus;
+
+		MIPS16e_compute_return_epc(regs, &oldinst);
+		value = regs->regs[reg];
+		StoreHW(addr, value, res);
+		if (res)
+			goto fault;
+		break;
+
+	case MIPS16e_sw_op:
+	case MIPS16e_swsp_op:
+	case MIPS16e_i8_op:	/* actually - MIPS16e_swrasp_func */
+		if (user && !access_ok(addr, 4))
+			goto sigbus;
+
+		MIPS16e_compute_return_epc(regs, &oldinst);
+		value = regs->regs[reg];
+		StoreW(addr, value, res);
+		if (res)
+			goto fault;
+		break;
+
+	case MIPS16e_sd_op:
+writeDW:
+#ifdef CONFIG_64BIT
+		/*
+		 * A 32-bit kernel might be running on a 64-bit processor.  But
+		 * if we're on a 32-bit processor and an i-cache incoherency
+		 * or race makes us see a 64-bit instruction here the sdl/sdr
+		 * would blow up, so for now we don't handle unaligned 64-bit
+		 * instructions on 32-bit kernels.
+		 */
+		if (user && !access_ok(addr, 8))
+			goto sigbus;
+
+		MIPS16e_compute_return_epc(regs, &oldinst);
+		value = regs->regs[reg];
+		StoreDW(addr, value, res);
+		if (res)
+			goto fault;
+		break;
+#endif /* CONFIG_64BIT */
+
+		/* Cannot handle 64-bit instructions in 32-bit kernel */
+		goto sigill;
+
+	default:
+		/*
+		 * Pheeee...  We encountered an yet unknown instruction or
+		 * cache coherence problem.  Die sucker, die ...
+		 */
+		goto sigill;
+	}
+
+#ifdef CONFIG_DEBUG_FS
+	unaligned_instructions++;
+#endif
+
+	return;
+
+fault:
+	/* roll back jump/branch */
+	regs->cp0_epc = origpc;
+	regs->regs[31] = orig31;
+	/* Did we have an exception handler installed? */
+	if (fixup_exception(regs))
+		return;
+
+	die_if_kernel("Unhandled kernel unaligned access", regs);
+	force_sig(SIGSEGV);
+
+	return;
+
+sigbus:
+	die_if_kernel("Unhandled kernel unaligned access", regs);
+	force_sig(SIGBUS);
+
+	return;
+
+sigill:
+	die_if_kernel
+	    ("Unhandled kernel unaligned access or invalid instruction", regs);
+	force_sig(SIGILL);
+}
+
+asmlinkage void do_ade(struct pt_regs *regs)
+{
+	enum ctx_state prev_state;
+	unsigned int *pc;
+
+	prev_state = exception_enter();
+	perf_sw_event(PERF_COUNT_SW_ALIGNMENT_FAULTS,
+			1, regs, regs->cp0_badvaddr);
+
+#ifdef CONFIG_64BIT
+	/*
+	 * check, if we are hitting space between CPU implemented maximum
+	 * virtual user address and 64bit maximum virtual user address
+	 * and do exception handling to get EFAULTs for get_user/put_user
+	 */
+	if ((regs->cp0_badvaddr >= (1UL << cpu_vmbits)) &&
+	    (regs->cp0_badvaddr < XKSSEG)) {
+		if (fixup_exception(regs)) {
+			current->thread.cp0_baduaddr = regs->cp0_badvaddr;
+			return;
+		}
+		goto sigbus;
+	}
+#endif
+
+	/*
+	 * Did we catch a fault trying to load an instruction?
+	 */
+	if (regs->cp0_badvaddr == regs->cp0_epc)
+		goto sigbus;
+
+	if (user_mode(regs) && !test_thread_flag(TIF_FIXADE))
+		goto sigbus;
+	if (unaligned_action == UNALIGNED_ACTION_SIGNAL)
+		goto sigbus;
+
+	/*
+	 * Do branch emulation only if we didn't forward the exception.
+	 * This is all so but ugly ...
+	 */
+
+	/*
+	 * Are we running in microMIPS mode?
+	 */
+	if (get_isa16_mode(regs->cp0_epc)) {
+		/*
+		 * Did we catch a fault trying to load an instruction in
+		 * 16-bit mode?
+		 */
+		if (regs->cp0_badvaddr == msk_isa16_mode(regs->cp0_epc))
+			goto sigbus;
+		if (unaligned_action == UNALIGNED_ACTION_SHOW)
+			show_registers(regs);
+
+		if (cpu_has_mmips) {
+			emulate_load_store_microMIPS(regs,
+				(void __user *)regs->cp0_badvaddr);
+			return;
+		}
+
+		if (cpu_has_mips16) {
+			emulate_load_store_MIPS16e(regs,
+				(void __user *)regs->cp0_badvaddr);
+			return;
+		}
+
+		goto sigbus;
+	}
+
+	if (unaligned_action == UNALIGNED_ACTION_SHOW)
+		show_registers(regs);
+	pc = (unsigned int *)exception_epc(regs);
+
+	emulate_load_store_insn(regs, (void __user *)regs->cp0_badvaddr, pc);
+
+	return;
+
+sigbus:
+	die_if_kernel("Kernel unaligned instruction access", regs);
+	force_sig(SIGBUS);
+
+	/*
+	 * XXX On return from the signal handler we should advance the epc
+	 */
+	exception_exit(prev_state);
+}
+
+#ifdef CONFIG_DEBUG_FS
+static int __init debugfs_unaligned(void)
+{
+	debugfs_create_u32("unaligned_instructions", S_IRUGO, mips_debugfs_dir,
+			   &unaligned_instructions);
+	debugfs_create_u32("unaligned_action", S_IRUGO | S_IWUSR,
+			   mips_debugfs_dir, &unaligned_action);
+	return 0;
+}
+arch_initcall(debugfs_unaligned);
+#endif
diff --git a/arch/mips/kernel/uprobes.c b/arch/mips/kernel/uprobes.c
new file mode 100644
index 000000000..6c063aa18
--- /dev/null
+++ b/arch/mips/kernel/uprobes.c
@@ -0,0 +1,263 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/highmem.h>
+#include <linux/kdebug.h>
+#include <linux/types.h>
+#include <linux/notifier.h>
+#include <linux/sched.h>
+#include <linux/uprobes.h>
+
+#include <asm/branch.h>
+#include <asm/cpu-features.h>
+#include <asm/ptrace.h>
+
+#include "probes-common.h"
+
+static inline int insn_has_delay_slot(const union mips_instruction insn)
+{
+	return __insn_has_delay_slot(insn);
+}
+
+/**
+ * arch_uprobe_analyze_insn - instruction analysis including validity and fixups.
+ * @mm: the probed address space.
+ * @arch_uprobe: the probepoint information.
+ * @addr: virtual address at which to install the probepoint
+ * Return 0 on success or a -ve number on error.
+ */
+int arch_uprobe_analyze_insn(struct arch_uprobe *aup,
+	struct mm_struct *mm, unsigned long addr)
+{
+	union mips_instruction inst;
+
+	/*
+	 * For the time being this also blocks attempts to use uprobes with
+	 * MIPS16 and microMIPS.
+	 */
+	if (addr & 0x03)
+		return -EINVAL;
+
+	inst.word = aup->insn[0];
+
+	if (__insn_is_compact_branch(inst)) {
+		pr_notice("Uprobes for compact branches are not supported\n");
+		return -EINVAL;
+	}
+
+	aup->ixol[0] = aup->insn[insn_has_delay_slot(inst)];
+	aup->ixol[1] = UPROBE_BRK_UPROBE_XOL;		/* NOP  */
+
+	return 0;
+}
+
+/**
+ * is_trap_insn - check if the instruction is a trap variant
+ * @insn: instruction to be checked.
+ * Returns true if @insn is a trap variant.
+ *
+ * This definition overrides the weak definition in kernel/events/uprobes.c.
+ * and is needed for the case where an architecture has multiple trap
+ * instructions (like PowerPC or MIPS).  We treat BREAK just like the more
+ * modern conditional trap instructions.
+ */
+bool is_trap_insn(uprobe_opcode_t *insn)
+{
+	union mips_instruction inst;
+
+	inst.word = *insn;
+
+	switch (inst.i_format.opcode) {
+	case spec_op:
+		switch (inst.r_format.func) {
+		case break_op:
+		case teq_op:
+		case tge_op:
+		case tgeu_op:
+		case tlt_op:
+		case tltu_op:
+		case tne_op:
+			return true;
+		}
+		break;
+
+	case bcond_op:	/* Yes, really ...  */
+		switch (inst.u_format.rt) {
+		case teqi_op:
+		case tgei_op:
+		case tgeiu_op:
+		case tlti_op:
+		case tltiu_op:
+		case tnei_op:
+			return true;
+		}
+		break;
+	}
+
+	return false;
+}
+
+#define UPROBE_TRAP_NR	ULONG_MAX
+
+/*
+ * arch_uprobe_pre_xol - prepare to execute out of line.
+ * @auprobe: the probepoint information.
+ * @regs: reflects the saved user state of current task.
+ */
+int arch_uprobe_pre_xol(struct arch_uprobe *aup, struct pt_regs *regs)
+{
+	struct uprobe_task *utask = current->utask;
+
+	/*
+	 * Now find the EPC where to resume after the breakpoint has been
+	 * dealt with.  This may require emulation of a branch.
+	 */
+	aup->resume_epc = regs->cp0_epc + 4;
+	if (insn_has_delay_slot((union mips_instruction) aup->insn[0])) {
+		__compute_return_epc_for_insn(regs,
+			(union mips_instruction) aup->insn[0]);
+		aup->resume_epc = regs->cp0_epc;
+	}
+	utask->autask.saved_trap_nr = current->thread.trap_nr;
+	current->thread.trap_nr = UPROBE_TRAP_NR;
+	regs->cp0_epc = current->utask->xol_vaddr;
+
+	return 0;
+}
+
+int arch_uprobe_post_xol(struct arch_uprobe *aup, struct pt_regs *regs)
+{
+	struct uprobe_task *utask = current->utask;
+
+	current->thread.trap_nr = utask->autask.saved_trap_nr;
+	regs->cp0_epc = aup->resume_epc;
+
+	return 0;
+}
+
+/*
+ * If xol insn itself traps and generates a signal(Say,
+ * SIGILL/SIGSEGV/etc), then detect the case where a singlestepped
+ * instruction jumps back to its own address. It is assumed that anything
+ * like do_page_fault/do_trap/etc sets thread.trap_nr != -1.
+ *
+ * arch_uprobe_pre_xol/arch_uprobe_post_xol save/restore thread.trap_nr,
+ * arch_uprobe_xol_was_trapped() simply checks that ->trap_nr is not equal to
+ * UPROBE_TRAP_NR == -1 set by arch_uprobe_pre_xol().
+ */
+bool arch_uprobe_xol_was_trapped(struct task_struct *tsk)
+{
+	if (tsk->thread.trap_nr != UPROBE_TRAP_NR)
+		return true;
+
+	return false;
+}
+
+int arch_uprobe_exception_notify(struct notifier_block *self,
+	unsigned long val, void *data)
+{
+	struct die_args *args = data;
+	struct pt_regs *regs = args->regs;
+
+	/* regs == NULL is a kernel bug */
+	if (WARN_ON(!regs))
+		return NOTIFY_DONE;
+
+	/* We are only interested in userspace traps */
+	if (!user_mode(regs))
+		return NOTIFY_DONE;
+
+	switch (val) {
+	case DIE_UPROBE:
+		if (uprobe_pre_sstep_notifier(regs))
+			return NOTIFY_STOP;
+		break;
+	case DIE_UPROBE_XOL:
+		if (uprobe_post_sstep_notifier(regs))
+			return NOTIFY_STOP;
+		break;
+	default:
+		break;
+	}
+
+	return 0;
+}
+
+/*
+ * This function gets called when XOL instruction either gets trapped or
+ * the thread has a fatal signal. Reset the instruction pointer to its
+ * probed address for the potential restart or for post mortem analysis.
+ */
+void arch_uprobe_abort_xol(struct arch_uprobe *aup,
+	struct pt_regs *regs)
+{
+	struct uprobe_task *utask = current->utask;
+
+	instruction_pointer_set(regs, utask->vaddr);
+}
+
+unsigned long arch_uretprobe_hijack_return_addr(
+	unsigned long trampoline_vaddr, struct pt_regs *regs)
+{
+	unsigned long ra;
+
+	ra = regs->regs[31];
+
+	/* Replace the return address with the trampoline address */
+	regs->regs[31] = trampoline_vaddr;
+
+	return ra;
+}
+
+/**
+ * set_swbp - store breakpoint at a given address.
+ * @auprobe: arch specific probepoint information.
+ * @mm: the probed process address space.
+ * @vaddr: the virtual address to insert the opcode.
+ *
+ * For mm @mm, store the breakpoint instruction at @vaddr.
+ * Return 0 (success) or a negative errno.
+ *
+ * This version overrides the weak version in kernel/events/uprobes.c.
+ * It is required to handle MIPS16 and microMIPS.
+ */
+int __weak set_swbp(struct arch_uprobe *auprobe, struct mm_struct *mm,
+	unsigned long vaddr)
+{
+	return uprobe_write_opcode(auprobe, mm, vaddr, UPROBE_SWBP_INSN);
+}
+
+void arch_uprobe_copy_ixol(struct page *page, unsigned long vaddr,
+				  void *src, unsigned long len)
+{
+	unsigned long kaddr, kstart;
+
+	/* Initialize the slot */
+	kaddr = (unsigned long)kmap_atomic(page);
+	kstart = kaddr + (vaddr & ~PAGE_MASK);
+	memcpy((void *)kstart, src, len);
+	flush_icache_range(kstart, kstart + len);
+	kunmap_atomic((void *)kaddr);
+}
+
+/**
+ * uprobe_get_swbp_addr - compute address of swbp given post-swbp regs
+ * @regs: Reflects the saved state of the task after it has hit a breakpoint
+ * instruction.
+ * Return the address of the breakpoint instruction.
+ *
+ * This overrides the weak version in kernel/events/uprobes.c.
+ */
+unsigned long uprobe_get_swbp_addr(struct pt_regs *regs)
+{
+	return instruction_pointer(regs);
+}
+
+/*
+ * See if the instruction can be emulated.
+ * Returns true if instruction was emulated, false otherwise.
+ *
+ * For now we always emulate so this function just returns false.
+ */
+bool arch_uprobe_skip_sstep(struct arch_uprobe *auprobe, struct pt_regs *regs)
+{
+	return false;
+}
diff --git a/arch/mips/kernel/vdso.c b/arch/mips/kernel/vdso.c
new file mode 100644
index 000000000..5fd9bf1d5
--- /dev/null
+++ b/arch/mips/kernel/vdso.c
@@ -0,0 +1,193 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2015 Imagination Technologies
+ * Author: Alex Smith <alex.smith@imgtec.com>
+ */
+
+#include <linux/binfmts.h>
+#include <linux/elf.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/ioport.h>
+#include <linux/kernel.h>
+#include <linux/mm.h>
+#include <linux/random.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/timekeeper_internal.h>
+
+#include <asm/abi.h>
+#include <asm/mips-cps.h>
+#include <asm/page.h>
+#include <asm/vdso.h>
+#include <vdso/helpers.h>
+#include <vdso/vsyscall.h>
+
+/* Kernel-provided data used by the VDSO. */
+static union mips_vdso_data mips_vdso_data __page_aligned_data;
+struct vdso_data *vdso_data = mips_vdso_data.data;
+
+/*
+ * Mapping for the VDSO data/GIC pages. The real pages are mapped manually, as
+ * what we map and where within the area they are mapped is determined at
+ * runtime.
+ */
+static struct page *no_pages[] = { NULL };
+static struct vm_special_mapping vdso_vvar_mapping = {
+	.name = "[vvar]",
+	.pages = no_pages,
+};
+
+static void __init init_vdso_image(struct mips_vdso_image *image)
+{
+	unsigned long num_pages, i;
+	unsigned long data_pfn;
+
+	BUG_ON(!PAGE_ALIGNED(image->data));
+	BUG_ON(!PAGE_ALIGNED(image->size));
+
+	num_pages = image->size / PAGE_SIZE;
+
+	data_pfn = __phys_to_pfn(__pa_symbol(image->data));
+	for (i = 0; i < num_pages; i++)
+		image->mapping.pages[i] = pfn_to_page(data_pfn + i);
+}
+
+static int __init init_vdso(void)
+{
+	init_vdso_image(&vdso_image);
+
+#ifdef CONFIG_MIPS32_O32
+	init_vdso_image(&vdso_image_o32);
+#endif
+
+#ifdef CONFIG_MIPS32_N32
+	init_vdso_image(&vdso_image_n32);
+#endif
+
+	return 0;
+}
+subsys_initcall(init_vdso);
+
+static unsigned long vdso_base(void)
+{
+	unsigned long base = STACK_TOP;
+
+	if (IS_ENABLED(CONFIG_MIPS_FP_SUPPORT)) {
+		/* Skip the delay slot emulation page */
+		base += PAGE_SIZE;
+	}
+
+	if (current->flags & PF_RANDOMIZE) {
+		base += prandom_u32_max(VDSO_RANDOMIZE_SIZE);
+		base = PAGE_ALIGN(base);
+	}
+
+	return base;
+}
+
+int arch_setup_additional_pages(struct linux_binprm *bprm, int uses_interp)
+{
+	struct mips_vdso_image *image = current->thread.abi->vdso;
+	struct mm_struct *mm = current->mm;
+	unsigned long gic_size, vvar_size, size, base, data_addr, vdso_addr, gic_pfn, gic_base;
+	struct vm_area_struct *vma;
+	int ret;
+
+	if (mmap_write_lock_killable(mm))
+		return -EINTR;
+
+	if (IS_ENABLED(CONFIG_MIPS_FP_SUPPORT)) {
+		/* Map delay slot emulation page */
+		base = mmap_region(NULL, STACK_TOP, PAGE_SIZE,
+				VM_READ | VM_EXEC |
+				VM_MAYREAD | VM_MAYWRITE | VM_MAYEXEC,
+				0, NULL);
+		if (IS_ERR_VALUE(base)) {
+			ret = base;
+			goto out;
+		}
+	}
+
+	/*
+	 * Determine total area size. This includes the VDSO data itself, the
+	 * data page, and the GIC user page if present. Always create a mapping
+	 * for the GIC user area if the GIC is present regardless of whether it
+	 * is the current clocksource, in case it comes into use later on. We
+	 * only map a page even though the total area is 64K, as we only need
+	 * the counter registers at the start.
+	 */
+	gic_size = mips_gic_present() ? PAGE_SIZE : 0;
+	vvar_size = gic_size + PAGE_SIZE;
+	size = vvar_size + image->size;
+
+	/*
+	 * Find a region that's large enough for us to perform the
+	 * colour-matching alignment below.
+	 */
+	if (cpu_has_dc_aliases)
+		size += shm_align_mask + 1;
+
+	base = get_unmapped_area(NULL, vdso_base(), size, 0, 0);
+	if (IS_ERR_VALUE(base)) {
+		ret = base;
+		goto out;
+	}
+
+	/*
+	 * If we suffer from dcache aliasing, ensure that the VDSO data page
+	 * mapping is coloured the same as the kernel's mapping of that memory.
+	 * This ensures that when the kernel updates the VDSO data userland
+	 * will observe it without requiring cache invalidations.
+	 */
+	if (cpu_has_dc_aliases) {
+		base = __ALIGN_MASK(base, shm_align_mask);
+		base += ((unsigned long)vdso_data - gic_size) & shm_align_mask;
+	}
+
+	data_addr = base + gic_size;
+	vdso_addr = data_addr + PAGE_SIZE;
+
+	vma = _install_special_mapping(mm, base, vvar_size,
+				       VM_READ | VM_MAYREAD,
+				       &vdso_vvar_mapping);
+	if (IS_ERR(vma)) {
+		ret = PTR_ERR(vma);
+		goto out;
+	}
+
+	/* Map GIC user page. */
+	if (gic_size) {
+		gic_base = (unsigned long)mips_gic_base + MIPS_GIC_USER_OFS;
+		gic_pfn = PFN_DOWN(__pa(gic_base));
+
+		ret = io_remap_pfn_range(vma, base, gic_pfn, gic_size,
+					 pgprot_noncached(vma->vm_page_prot));
+		if (ret)
+			goto out;
+	}
+
+	/* Map data page. */
+	ret = remap_pfn_range(vma, data_addr,
+			      virt_to_phys(vdso_data) >> PAGE_SHIFT,
+			      PAGE_SIZE, vma->vm_page_prot);
+	if (ret)
+		goto out;
+
+	/* Map VDSO image. */
+	vma = _install_special_mapping(mm, vdso_addr, image->size,
+				       VM_READ | VM_EXEC |
+				       VM_MAYREAD | VM_MAYWRITE | VM_MAYEXEC,
+				       &image->mapping);
+	if (IS_ERR(vma)) {
+		ret = PTR_ERR(vma);
+		goto out;
+	}
+
+	mm->context.vdso = (void *)vdso_addr;
+	ret = 0;
+
+out:
+	mmap_write_unlock(mm);
+	return ret;
+}
diff --git a/arch/mips/kernel/vmlinux.lds.S b/arch/mips/kernel/vmlinux.lds.S
new file mode 100644
index 000000000..91d6a5360
--- /dev/null
+++ b/arch/mips/kernel/vmlinux.lds.S
@@ -0,0 +1,243 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#include <asm/asm-offsets.h>
+#include <asm/thread_info.h>
+
+#define PAGE_SIZE _PAGE_SIZE
+
+/*
+ * Put .bss..swapper_pg_dir as the first thing in .bss. This will
+ * ensure that it has .bss alignment (64K).
+ */
+#define BSS_FIRST_SECTIONS *(.bss..swapper_pg_dir)
+
+/* Cavium Octeon should not have a separate PT_NOTE Program Header. */
+#ifndef CONFIG_CAVIUM_OCTEON_SOC
+#define EMITS_PT_NOTE
+#endif
+
+#define RUNTIME_DISCARD_EXIT
+
+#include <asm-generic/vmlinux.lds.h>
+
+#undef mips
+#define mips mips
+OUTPUT_ARCH(mips)
+ENTRY(kernel_entry)
+PHDRS {
+	text PT_LOAD FLAGS(7);	/* RWX */
+#ifndef CONFIG_CAVIUM_OCTEON_SOC
+	note PT_NOTE FLAGS(4);	/* R__ */
+#endif /* CAVIUM_OCTEON_SOC */
+}
+
+#ifdef CONFIG_32BIT
+	#ifdef CONFIG_CPU_LITTLE_ENDIAN
+		jiffies	 = jiffies_64;
+	#else
+		jiffies	 = jiffies_64 + 4;
+	#endif
+#else
+	jiffies	 = jiffies_64;
+#endif
+
+SECTIONS
+{
+#ifdef CONFIG_BOOT_ELF64
+	/* Read-only sections, merged into text segment: */
+	/* . = 0xc000000000000000; */
+
+	/* This is the value for an Origin kernel, taken from an IRIX kernel.  */
+	/* . = 0xc00000000001c000; */
+
+	/* Set the vaddr for the text segment to a value
+	 *   >= 0xa800 0000 0001 9000 if no symmon is going to configured
+	 *   >= 0xa800 0000 0030 0000 otherwise
+	 */
+
+	/* . = 0xa800000000300000; */
+	. = 0xffffffff80300000;
+#endif
+	. = LINKER_LOAD_ADDRESS;
+	/* read-only */
+	_text = .;	/* Text and read-only data */
+	.text : {
+		TEXT_TEXT
+		SCHED_TEXT
+		CPUIDLE_TEXT
+		LOCK_TEXT
+		KPROBES_TEXT
+		IRQENTRY_TEXT
+		SOFTIRQENTRY_TEXT
+		*(.fixup)
+		*(.gnu.warning)
+		. = ALIGN(16);
+		*(.got)	/* Global offset table */
+	} :text = 0
+	_etext = .;	/* End of text section */
+
+	EXCEPTION_TABLE(16)
+
+	/* Exception table for data bus errors */
+	__dbe_table : {
+		__start___dbe_table = .;
+		KEEP(*(__dbe_table))
+		__stop___dbe_table = .;
+	}
+
+	_sdata = .;			/* Start of data section */
+	RO_DATA(4096)
+
+	/* writeable */
+	.data : {	/* Data */
+		. = . + DATAOFFSET;		/* for CONFIG_MAPPED_KERNEL */
+
+		INIT_TASK_DATA(THREAD_SIZE)
+		NOSAVE_DATA
+		PAGE_ALIGNED_DATA(PAGE_SIZE)
+		CACHELINE_ALIGNED_DATA(1 << CONFIG_MIPS_L1_CACHE_SHIFT)
+		READ_MOSTLY_DATA(1 << CONFIG_MIPS_L1_CACHE_SHIFT)
+		DATA_DATA
+		CONSTRUCTORS
+	}
+	BUG_TABLE
+	_gp = . + 0x8000;
+	.lit8 : {
+		*(.lit8)
+	}
+	.lit4 : {
+		*(.lit4)
+	}
+	/* We want the small data sections together, so single-instruction offsets
+	   can access them all, and initialized data all before uninitialized, so
+	   we can shorten the on-disk segment size.  */
+	.sdata : {
+		*(.sdata)
+	}
+	_edata =  .;			/* End of data section */
+
+	/* will be freed after init */
+	. = ALIGN(PAGE_SIZE);		/* Init code and data */
+	__init_begin = .;
+	INIT_TEXT_SECTION(PAGE_SIZE)
+	INIT_DATA_SECTION(16)
+
+	. = ALIGN(4);
+	.mips.machines.init : AT(ADDR(.mips.machines.init) - LOAD_OFFSET) {
+		__mips_machines_start = .;
+		KEEP(*(.mips.machines.init))
+		__mips_machines_end = .;
+	}
+
+	/* .exit.text is discarded at runtime, not link time, to deal with
+	 * references from .rodata
+	 */
+	.exit.text : {
+		EXIT_TEXT
+	}
+	.exit.data : {
+		EXIT_DATA
+	}
+#ifdef CONFIG_SMP
+	PERCPU_SECTION(1 << CONFIG_MIPS_L1_CACHE_SHIFT)
+#endif
+
+	.rel.dyn : ALIGN(8) {
+		*(.rel)
+		*(.rel*)
+	}
+
+#ifdef CONFIG_MIPS_ELF_APPENDED_DTB
+	STRUCT_ALIGN();
+	.appended_dtb : AT(ADDR(.appended_dtb) - LOAD_OFFSET) {
+		*(.appended_dtb)
+		KEEP(*(.appended_dtb))
+	}
+#endif
+
+#ifdef CONFIG_RELOCATABLE
+	. = ALIGN(4);
+
+	.data.reloc : {
+		_relocation_start = .;
+		/*
+		 * Space for relocation table
+		 * This needs to be filled so that the
+		 * relocs tool can overwrite the content.
+		 * An invalid value is left at the start of the
+		 * section to abort relocation if the table
+		 * has not been filled in.
+		 */
+		LONG(0xFFFFFFFF);
+		FILL(0);
+		. += CONFIG_RELOCATION_TABLE_SIZE - 4;
+		_relocation_end = .;
+	}
+#endif
+
+#ifdef CONFIG_MIPS_RAW_APPENDED_DTB
+	.fill : {
+		FILL(0);
+		BYTE(0);
+		STRUCT_ALIGN();
+	}
+	__appended_dtb = .;
+	/* leave space for appended DTB */
+	. += 0x100000;
+#endif
+	/*
+	 * Align to 64K in attempt to eliminate holes before the
+	 * .bss..swapper_pg_dir section at the start of .bss.  This
+	 * also satisfies PAGE_SIZE alignment as the largest page size
+	 * allowed is 64K.
+	 */
+	. = ALIGN(0x10000);
+	__init_end = .;
+	/* freed after init ends here */
+
+	/*
+	 * Force .bss to 64K alignment so that .bss..swapper_pg_dir
+	 * gets that alignment.	 .sbss should be empty, so there will be
+	 * no holes after __init_end. */
+	BSS_SECTION(0, 0x10000, 8)
+
+	_end = . ;
+
+	/* These mark the ABI of the kernel for debuggers.  */
+	.mdebug.abi32 : {
+		KEEP(*(.mdebug.abi32))
+	}
+	.mdebug.abi64 : {
+		KEEP(*(.mdebug.abi64))
+	}
+
+	/* This is the MIPS specific mdebug section.  */
+	.mdebug : {
+		*(.mdebug)
+	}
+
+	STABS_DEBUG
+	DWARF_DEBUG
+	ELF_DETAILS
+
+	/* These must appear regardless of  .  */
+	.gptab.sdata : {
+		*(.gptab.data)
+		*(.gptab.sdata)
+	}
+	.gptab.sbss : {
+		*(.gptab.bss)
+		*(.gptab.sbss)
+	}
+
+	/* Sections to be discarded */
+	DISCARDS
+	/DISCARD/ : {
+		/* ABI crap starts here */
+		*(.MIPS.abiflags)
+		*(.MIPS.options)
+		*(.gnu.attributes)
+		*(.options)
+		*(.pdr)
+		*(.reginfo)
+	}
+}
diff --git a/arch/mips/kernel/vpe-cmp.c b/arch/mips/kernel/vpe-cmp.c
new file mode 100644
index 000000000..92140edb3
--- /dev/null
+++ b/arch/mips/kernel/vpe-cmp.c
@@ -0,0 +1,180 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2004, 2005 MIPS Technologies, Inc.  All rights reserved.
+ * Copyright (C) 2013 Imagination Technologies Ltd.
+ */
+#include <linux/kernel.h>
+#include <linux/device.h>
+#include <linux/fs.h>
+#include <linux/slab.h>
+#include <linux/export.h>
+
+#include <asm/vpe.h>
+
+static int major;
+
+void cleanup_tc(struct tc *tc)
+{
+
+}
+
+static ssize_t store_kill(struct device *dev, struct device_attribute *attr,
+			  const char *buf, size_t len)
+{
+	struct vpe *vpe = get_vpe(aprp_cpu_index());
+	struct vpe_notifications *notifier;
+
+	list_for_each_entry(notifier, &vpe->notify, list)
+		notifier->stop(aprp_cpu_index());
+
+	release_progmem(vpe->load_addr);
+	vpe->state = VPE_STATE_UNUSED;
+
+	return len;
+}
+static DEVICE_ATTR(kill, S_IWUSR, NULL, store_kill);
+
+static ssize_t ntcs_show(struct device *cd, struct device_attribute *attr,
+			 char *buf)
+{
+	struct vpe *vpe = get_vpe(aprp_cpu_index());
+
+	return sprintf(buf, "%d\n", vpe->ntcs);
+}
+
+static ssize_t ntcs_store(struct device *dev, struct device_attribute *attr,
+			  const char *buf, size_t len)
+{
+	struct vpe *vpe = get_vpe(aprp_cpu_index());
+	unsigned long new;
+	int ret;
+
+	ret = kstrtoul(buf, 0, &new);
+	if (ret < 0)
+		return ret;
+
+	/* APRP can only reserve one TC in a VPE and no more. */
+	if (new != 1)
+		return -EINVAL;
+
+	vpe->ntcs = new;
+
+	return len;
+}
+static DEVICE_ATTR_RW(ntcs);
+
+static struct attribute *vpe_attrs[] = {
+	&dev_attr_kill.attr,
+	&dev_attr_ntcs.attr,
+	NULL,
+};
+ATTRIBUTE_GROUPS(vpe);
+
+static void vpe_device_release(struct device *cd)
+{
+}
+
+static struct class vpe_class = {
+	.name = "vpe",
+	.owner = THIS_MODULE,
+	.dev_release = vpe_device_release,
+	.dev_groups = vpe_groups,
+};
+
+static struct device vpe_device;
+
+int __init vpe_module_init(void)
+{
+	struct vpe *v = NULL;
+	struct tc *t;
+	int err;
+
+	if (!cpu_has_mipsmt) {
+		pr_warn("VPE loader: not a MIPS MT capable processor\n");
+		return -ENODEV;
+	}
+
+	if (num_possible_cpus() - aprp_cpu_index() < 1) {
+		pr_warn("No VPEs reserved for AP/SP, not initialize VPE loader\n"
+			"Pass maxcpus=<n> argument as kernel argument\n");
+		return -ENODEV;
+	}
+
+	major = register_chrdev(0, VPE_MODULE_NAME, &vpe_fops);
+	if (major < 0) {
+		pr_warn("VPE loader: unable to register character device\n");
+		return major;
+	}
+
+	err = class_register(&vpe_class);
+	if (err) {
+		pr_err("vpe_class registration failed\n");
+		goto out_chrdev;
+	}
+
+	device_initialize(&vpe_device);
+	vpe_device.class	= &vpe_class;
+	vpe_device.parent	= NULL;
+	dev_set_name(&vpe_device, "vpe_sp");
+	vpe_device.devt = MKDEV(major, VPE_MODULE_MINOR);
+	err = device_add(&vpe_device);
+	if (err) {
+		pr_err("Adding vpe_device failed\n");
+		goto out_class;
+	}
+
+	t = alloc_tc(aprp_cpu_index());
+	if (!t) {
+		pr_warn("VPE: unable to allocate TC\n");
+		err = -ENOMEM;
+		goto out_dev;
+	}
+
+	/* VPE */
+	v = alloc_vpe(aprp_cpu_index());
+	if (v == NULL) {
+		pr_warn("VPE: unable to allocate VPE\n");
+		kfree(t);
+		err = -ENOMEM;
+		goto out_dev;
+	}
+
+	v->ntcs = 1;
+
+	/* add the tc to the list of this vpe's tc's. */
+	list_add(&t->tc, &v->tc);
+
+	/* TC */
+	t->pvpe = v;	/* set the parent vpe */
+
+	return 0;
+
+out_dev:
+	device_del(&vpe_device);
+
+out_class:
+	put_device(&vpe_device);
+	class_unregister(&vpe_class);
+
+out_chrdev:
+	unregister_chrdev(major, VPE_MODULE_NAME);
+
+	return err;
+}
+
+void __exit vpe_module_exit(void)
+{
+	struct vpe *v, *n;
+
+	device_unregister(&vpe_device);
+	class_unregister(&vpe_class);
+	unregister_chrdev(major, VPE_MODULE_NAME);
+
+	/* No locking needed here */
+	list_for_each_entry_safe(v, n, &vpecontrol.vpe_list, list)
+		if (v->state != VPE_STATE_UNUSED)
+			release_vpe(v);
+}
diff --git a/arch/mips/kernel/vpe-mt.c b/arch/mips/kernel/vpe-mt.c
new file mode 100644
index 000000000..84a82b551
--- /dev/null
+++ b/arch/mips/kernel/vpe-mt.c
@@ -0,0 +1,521 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2004, 2005 MIPS Technologies, Inc.  All rights reserved.
+ * Copyright (C) 2013 Imagination Technologies Ltd.
+ */
+#include <linux/kernel.h>
+#include <linux/device.h>
+#include <linux/fs.h>
+#include <linux/slab.h>
+#include <linux/export.h>
+
+#include <asm/mipsregs.h>
+#include <asm/mipsmtregs.h>
+#include <asm/mips_mt.h>
+#include <asm/vpe.h>
+
+static int major;
+
+/* The number of TCs and VPEs physically available on the core */
+static int hw_tcs, hw_vpes;
+
+/* We are prepared so configure and start the VPE... */
+int vpe_run(struct vpe *v)
+{
+	unsigned long flags, val, dmt_flag;
+	struct vpe_notifications *notifier;
+	unsigned int vpeflags;
+	struct tc *t;
+
+	/* check we are the Master VPE */
+	local_irq_save(flags);
+	val = read_c0_vpeconf0();
+	if (!(val & VPECONF0_MVP)) {
+		pr_warn("VPE loader: only Master VPE's are able to config MT\n");
+		local_irq_restore(flags);
+
+		return -1;
+	}
+
+	dmt_flag = dmt();
+	vpeflags = dvpe();
+
+	if (list_empty(&v->tc)) {
+		evpe(vpeflags);
+		emt(dmt_flag);
+		local_irq_restore(flags);
+
+		pr_warn("VPE loader: No TC's associated with VPE %d\n",
+			v->minor);
+
+		return -ENOEXEC;
+	}
+
+	t = list_first_entry(&v->tc, struct tc, tc);
+
+	/* Put MVPE's into 'configuration state' */
+	set_c0_mvpcontrol(MVPCONTROL_VPC);
+
+	settc(t->index);
+
+	/* should check it is halted, and not activated */
+	if ((read_tc_c0_tcstatus() & TCSTATUS_A) ||
+	   !(read_tc_c0_tchalt() & TCHALT_H)) {
+		evpe(vpeflags);
+		emt(dmt_flag);
+		local_irq_restore(flags);
+
+		pr_warn("VPE loader: TC %d is already active!\n",
+			t->index);
+
+		return -ENOEXEC;
+	}
+
+	/*
+	 * Write the address we want it to start running from in the TCPC
+	 * register.
+	 */
+	write_tc_c0_tcrestart((unsigned long)v->__start);
+	write_tc_c0_tccontext((unsigned long)0);
+
+	/*
+	 * Mark the TC as activated, not interrupt exempt and not dynamically
+	 * allocatable
+	 */
+	val = read_tc_c0_tcstatus();
+	val = (val & ~(TCSTATUS_DA | TCSTATUS_IXMT)) | TCSTATUS_A;
+	write_tc_c0_tcstatus(val);
+
+	write_tc_c0_tchalt(read_tc_c0_tchalt() & ~TCHALT_H);
+
+	/*
+	 * The sde-kit passes 'memsize' to __start in $a3, so set something
+	 * here...  Or set $a3 to zero and define DFLT_STACK_SIZE and
+	 * DFLT_HEAP_SIZE when you compile your program
+	 */
+	mttgpr(6, v->ntcs);
+	mttgpr(7, physical_memsize);
+
+	/* set up VPE1 */
+	/*
+	 * bind the TC to VPE 1 as late as possible so we only have the final
+	 * VPE registers to set up, and so an EJTAG probe can trigger on it
+	 */
+	write_tc_c0_tcbind((read_tc_c0_tcbind() & ~TCBIND_CURVPE) | 1);
+
+	write_vpe_c0_vpeconf0(read_vpe_c0_vpeconf0() & ~(VPECONF0_VPA));
+
+	back_to_back_c0_hazard();
+
+	/* Set up the XTC bit in vpeconf0 to point at our tc */
+	write_vpe_c0_vpeconf0((read_vpe_c0_vpeconf0() & ~(VPECONF0_XTC))
+			      | (t->index << VPECONF0_XTC_SHIFT));
+
+	back_to_back_c0_hazard();
+
+	/* enable this VPE */
+	write_vpe_c0_vpeconf0(read_vpe_c0_vpeconf0() | VPECONF0_VPA);
+
+	/* clear out any left overs from a previous program */
+	write_vpe_c0_status(0);
+	write_vpe_c0_cause(0);
+
+	/* take system out of configuration state */
+	clear_c0_mvpcontrol(MVPCONTROL_VPC);
+
+	/*
+	 * SMVP kernels manage VPE enable independently, but uniprocessor
+	 * kernels need to turn it on, even if that wasn't the pre-dvpe() state.
+	 */
+#ifdef CONFIG_SMP
+	evpe(vpeflags);
+#else
+	evpe(EVPE_ENABLE);
+#endif
+	emt(dmt_flag);
+	local_irq_restore(flags);
+
+	list_for_each_entry(notifier, &v->notify, list)
+		notifier->start(VPE_MODULE_MINOR);
+
+	return 0;
+}
+
+void cleanup_tc(struct tc *tc)
+{
+	unsigned long flags;
+	unsigned int mtflags, vpflags;
+	int tmp;
+
+	local_irq_save(flags);
+	mtflags = dmt();
+	vpflags = dvpe();
+	/* Put MVPE's into 'configuration state' */
+	set_c0_mvpcontrol(MVPCONTROL_VPC);
+
+	settc(tc->index);
+	tmp = read_tc_c0_tcstatus();
+
+	/* mark not allocated and not dynamically allocatable */
+	tmp &= ~(TCSTATUS_A | TCSTATUS_DA);
+	tmp |= TCSTATUS_IXMT;	/* interrupt exempt */
+	write_tc_c0_tcstatus(tmp);
+
+	write_tc_c0_tchalt(TCHALT_H);
+	mips_ihb();
+
+	clear_c0_mvpcontrol(MVPCONTROL_VPC);
+	evpe(vpflags);
+	emt(mtflags);
+	local_irq_restore(flags);
+}
+
+/* module wrapper entry points */
+/* give me a vpe */
+void *vpe_alloc(void)
+{
+	int i;
+	struct vpe *v;
+
+	/* find a vpe */
+	for (i = 1; i < MAX_VPES; i++) {
+		v = get_vpe(i);
+		if (v != NULL) {
+			v->state = VPE_STATE_INUSE;
+			return v;
+		}
+	}
+	return NULL;
+}
+EXPORT_SYMBOL(vpe_alloc);
+
+/* start running from here */
+int vpe_start(void *vpe, unsigned long start)
+{
+	struct vpe *v = vpe;
+
+	v->__start = start;
+	return vpe_run(v);
+}
+EXPORT_SYMBOL(vpe_start);
+
+/* halt it for now */
+int vpe_stop(void *vpe)
+{
+	struct vpe *v = vpe;
+	struct tc *t;
+	unsigned int evpe_flags;
+
+	evpe_flags = dvpe();
+
+	t = list_entry(v->tc.next, struct tc, tc);
+	if (t != NULL) {
+		settc(t->index);
+		write_vpe_c0_vpeconf0(read_vpe_c0_vpeconf0() & ~VPECONF0_VPA);
+	}
+
+	evpe(evpe_flags);
+
+	return 0;
+}
+EXPORT_SYMBOL(vpe_stop);
+
+/* I've done with it thank you */
+int vpe_free(void *vpe)
+{
+	struct vpe *v = vpe;
+	struct tc *t;
+	unsigned int evpe_flags;
+
+	t = list_entry(v->tc.next, struct tc, tc);
+	if (t == NULL)
+		return -ENOEXEC;
+
+	evpe_flags = dvpe();
+
+	/* Put MVPE's into 'configuration state' */
+	set_c0_mvpcontrol(MVPCONTROL_VPC);
+
+	settc(t->index);
+	write_vpe_c0_vpeconf0(read_vpe_c0_vpeconf0() & ~VPECONF0_VPA);
+
+	/* halt the TC */
+	write_tc_c0_tchalt(TCHALT_H);
+	mips_ihb();
+
+	/* mark the TC unallocated */
+	write_tc_c0_tcstatus(read_tc_c0_tcstatus() & ~TCSTATUS_A);
+
+	v->state = VPE_STATE_UNUSED;
+
+	clear_c0_mvpcontrol(MVPCONTROL_VPC);
+	evpe(evpe_flags);
+
+	return 0;
+}
+EXPORT_SYMBOL(vpe_free);
+
+static ssize_t store_kill(struct device *dev, struct device_attribute *attr,
+			  const char *buf, size_t len)
+{
+	struct vpe *vpe = get_vpe(aprp_cpu_index());
+	struct vpe_notifications *notifier;
+
+	list_for_each_entry(notifier, &vpe->notify, list)
+		notifier->stop(aprp_cpu_index());
+
+	release_progmem(vpe->load_addr);
+	cleanup_tc(get_tc(aprp_cpu_index()));
+	vpe_stop(vpe);
+	vpe_free(vpe);
+
+	return len;
+}
+static DEVICE_ATTR(kill, S_IWUSR, NULL, store_kill);
+
+static ssize_t ntcs_show(struct device *cd, struct device_attribute *attr,
+			 char *buf)
+{
+	struct vpe *vpe = get_vpe(aprp_cpu_index());
+
+	return sprintf(buf, "%d\n", vpe->ntcs);
+}
+
+static ssize_t ntcs_store(struct device *dev, struct device_attribute *attr,
+			  const char *buf, size_t len)
+{
+	struct vpe *vpe = get_vpe(aprp_cpu_index());
+	unsigned long new;
+	int ret;
+
+	ret = kstrtoul(buf, 0, &new);
+	if (ret < 0)
+		return ret;
+
+	if (new == 0 || new > (hw_tcs - aprp_cpu_index()))
+		return -EINVAL;
+
+	vpe->ntcs = new;
+
+	return len;
+}
+static DEVICE_ATTR_RW(ntcs);
+
+static struct attribute *vpe_attrs[] = {
+	&dev_attr_kill.attr,
+	&dev_attr_ntcs.attr,
+	NULL,
+};
+ATTRIBUTE_GROUPS(vpe);
+
+static void vpe_device_release(struct device *cd)
+{
+}
+
+static struct class vpe_class = {
+	.name = "vpe",
+	.owner = THIS_MODULE,
+	.dev_release = vpe_device_release,
+	.dev_groups = vpe_groups,
+};
+
+static struct device vpe_device;
+
+int __init vpe_module_init(void)
+{
+	unsigned int mtflags, vpflags;
+	unsigned long flags, val;
+	struct vpe *v = NULL;
+	struct tc *t;
+	int tc, err;
+
+	if (!cpu_has_mipsmt) {
+		pr_warn("VPE loader: not a MIPS MT capable processor\n");
+		return -ENODEV;
+	}
+
+	if (vpelimit == 0) {
+		pr_warn("No VPEs reserved for AP/SP, not initialize VPE loader\n"
+			"Pass maxvpes=<n> argument as kernel argument\n");
+
+		return -ENODEV;
+	}
+
+	if (aprp_cpu_index() == 0) {
+		pr_warn("No TCs reserved for AP/SP, not initialize VPE loader\n"
+			"Pass maxtcs=<n> argument as kernel argument\n");
+
+		return -ENODEV;
+	}
+
+	major = register_chrdev(0, VPE_MODULE_NAME, &vpe_fops);
+	if (major < 0) {
+		pr_warn("VPE loader: unable to register character device\n");
+		return major;
+	}
+
+	err = class_register(&vpe_class);
+	if (err) {
+		pr_err("vpe_class registration failed\n");
+		goto out_chrdev;
+	}
+
+	device_initialize(&vpe_device);
+	vpe_device.class	= &vpe_class;
+	vpe_device.parent	= NULL;
+	dev_set_name(&vpe_device, "vpe1");
+	vpe_device.devt = MKDEV(major, VPE_MODULE_MINOR);
+	err = device_add(&vpe_device);
+	if (err) {
+		pr_err("Adding vpe_device failed\n");
+		goto out_class;
+	}
+
+	local_irq_save(flags);
+	mtflags = dmt();
+	vpflags = dvpe();
+
+	/* Put MVPE's into 'configuration state' */
+	set_c0_mvpcontrol(MVPCONTROL_VPC);
+
+	val = read_c0_mvpconf0();
+	hw_tcs = (val & MVPCONF0_PTC) + 1;
+	hw_vpes = ((val & MVPCONF0_PVPE) >> MVPCONF0_PVPE_SHIFT) + 1;
+
+	for (tc = aprp_cpu_index(); tc < hw_tcs; tc++) {
+		/*
+		 * Must re-enable multithreading temporarily or in case we
+		 * reschedule send IPIs or similar we might hang.
+		 */
+		clear_c0_mvpcontrol(MVPCONTROL_VPC);
+		evpe(vpflags);
+		emt(mtflags);
+		local_irq_restore(flags);
+		t = alloc_tc(tc);
+		if (!t) {
+			err = -ENOMEM;
+			goto out_dev;
+		}
+
+		local_irq_save(flags);
+		mtflags = dmt();
+		vpflags = dvpe();
+		set_c0_mvpcontrol(MVPCONTROL_VPC);
+
+		/* VPE's */
+		if (tc < hw_tcs) {
+			settc(tc);
+
+			v = alloc_vpe(tc);
+			if (v == NULL) {
+				pr_warn("VPE: unable to allocate VPE\n");
+				goto out_reenable;
+			}
+
+			v->ntcs = hw_tcs - aprp_cpu_index();
+
+			/* add the tc to the list of this vpe's tc's. */
+			list_add(&t->tc, &v->tc);
+
+			/* deactivate all but vpe0 */
+			if (tc >= aprp_cpu_index()) {
+				unsigned long tmp = read_vpe_c0_vpeconf0();
+
+				tmp &= ~VPECONF0_VPA;
+
+				/* master VPE */
+				tmp |= VPECONF0_MVP;
+				write_vpe_c0_vpeconf0(tmp);
+			}
+
+			/* disable multi-threading with TC's */
+			write_vpe_c0_vpecontrol(read_vpe_c0_vpecontrol() &
+						~VPECONTROL_TE);
+
+			if (tc >= vpelimit) {
+				/*
+				 * Set config to be the same as vpe0,
+				 * particularly kseg0 coherency alg
+				 */
+				write_vpe_c0_config(read_c0_config());
+			}
+		}
+
+		/* TC's */
+		t->pvpe = v;	/* set the parent vpe */
+
+		if (tc >= aprp_cpu_index()) {
+			unsigned long tmp;
+
+			settc(tc);
+
+			/*
+			 * A TC that is bound to any other VPE gets bound to
+			 * VPE0, ideally I'd like to make it homeless but it
+			 * doesn't appear to let me bind a TC to a non-existent
+			 * VPE. Which is perfectly reasonable.
+			 *
+			 * The (un)bound state is visible to an EJTAG probe so
+			 * may notify GDB...
+			 */
+			tmp = read_tc_c0_tcbind();
+			if (tmp & TCBIND_CURVPE) {
+				/* tc is bound >vpe0 */
+				write_tc_c0_tcbind(tmp & ~TCBIND_CURVPE);
+
+				t->pvpe = get_vpe(0);	/* set the parent vpe */
+			}
+
+			/* halt the TC */
+			write_tc_c0_tchalt(TCHALT_H);
+			mips_ihb();
+
+			tmp = read_tc_c0_tcstatus();
+
+			/* mark not activated and not dynamically allocatable */
+			tmp &= ~(TCSTATUS_A | TCSTATUS_DA);
+			tmp |= TCSTATUS_IXMT;	/* interrupt exempt */
+			write_tc_c0_tcstatus(tmp);
+		}
+	}
+
+out_reenable:
+	/* release config state */
+	clear_c0_mvpcontrol(MVPCONTROL_VPC);
+
+	evpe(vpflags);
+	emt(mtflags);
+	local_irq_restore(flags);
+
+	return 0;
+
+out_dev:
+	device_del(&vpe_device);
+
+out_class:
+	put_device(&vpe_device);
+	class_unregister(&vpe_class);
+
+out_chrdev:
+	unregister_chrdev(major, VPE_MODULE_NAME);
+
+	return err;
+}
+
+void __exit vpe_module_exit(void)
+{
+	struct vpe *v, *n;
+
+	device_unregister(&vpe_device);
+	class_unregister(&vpe_class);
+	unregister_chrdev(major, VPE_MODULE_NAME);
+
+	/* No locking needed here */
+	list_for_each_entry_safe(v, n, &vpecontrol.vpe_list, list) {
+		if (v->state != VPE_STATE_UNUSED)
+			release_vpe(v);
+	}
+}
diff --git a/arch/mips/kernel/vpe.c b/arch/mips/kernel/vpe.c
new file mode 100644
index 000000000..132949727
--- /dev/null
+++ b/arch/mips/kernel/vpe.c
@@ -0,0 +1,900 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2004, 2005 MIPS Technologies, Inc.  All rights reserved.
+ * Copyright (C) 2013 Imagination Technologies Ltd.
+ *
+ * VPE spport module for loading a MIPS SP program into VPE1. The SP
+ * environment is rather simple since there are no TLBs. It needs
+ * to be relocatable (or partiall linked). Initialize your stack in
+ * the startup-code. The loader looks for the symbol __start and sets
+ * up the execution to resume from there. To load and run, simply do
+ * a cat SP 'binary' to the /dev/vpe1 device.
+ */
+#include <linux/kernel.h>
+#include <linux/device.h>
+#include <linux/fs.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/list.h>
+#include <linux/vmalloc.h>
+#include <linux/elf.h>
+#include <linux/seq_file.h>
+#include <linux/syscalls.h>
+#include <linux/moduleloader.h>
+#include <linux/interrupt.h>
+#include <linux/poll.h>
+#include <linux/memblock.h>
+#include <asm/mipsregs.h>
+#include <asm/mipsmtregs.h>
+#include <asm/cacheflush.h>
+#include <linux/atomic.h>
+#include <asm/mips_mt.h>
+#include <asm/processor.h>
+#include <asm/vpe.h>
+
+#ifndef ARCH_SHF_SMALL
+#define ARCH_SHF_SMALL 0
+#endif
+
+/* If this is set, the section belongs in the init part of the module */
+#define INIT_OFFSET_MASK (1UL << (BITS_PER_LONG-1))
+
+struct vpe_control vpecontrol = {
+	.vpe_list_lock	= __SPIN_LOCK_UNLOCKED(vpe_list_lock),
+	.vpe_list	= LIST_HEAD_INIT(vpecontrol.vpe_list),
+	.tc_list_lock	= __SPIN_LOCK_UNLOCKED(tc_list_lock),
+	.tc_list	= LIST_HEAD_INIT(vpecontrol.tc_list)
+};
+
+/* get the vpe associated with this minor */
+struct vpe *get_vpe(int minor)
+{
+	struct vpe *res, *v;
+
+	if (!cpu_has_mipsmt)
+		return NULL;
+
+	res = NULL;
+	spin_lock(&vpecontrol.vpe_list_lock);
+	list_for_each_entry(v, &vpecontrol.vpe_list, list) {
+		if (v->minor == VPE_MODULE_MINOR) {
+			res = v;
+			break;
+		}
+	}
+	spin_unlock(&vpecontrol.vpe_list_lock);
+
+	return res;
+}
+
+/* get the vpe associated with this minor */
+struct tc *get_tc(int index)
+{
+	struct tc *res, *t;
+
+	res = NULL;
+	spin_lock(&vpecontrol.tc_list_lock);
+	list_for_each_entry(t, &vpecontrol.tc_list, list) {
+		if (t->index == index) {
+			res = t;
+			break;
+		}
+	}
+	spin_unlock(&vpecontrol.tc_list_lock);
+
+	return res;
+}
+
+/* allocate a vpe and associate it with this minor (or index) */
+struct vpe *alloc_vpe(int minor)
+{
+	struct vpe *v;
+
+	v = kzalloc(sizeof(struct vpe), GFP_KERNEL);
+	if (v == NULL)
+		goto out;
+
+	INIT_LIST_HEAD(&v->tc);
+	spin_lock(&vpecontrol.vpe_list_lock);
+	list_add_tail(&v->list, &vpecontrol.vpe_list);
+	spin_unlock(&vpecontrol.vpe_list_lock);
+
+	INIT_LIST_HEAD(&v->notify);
+	v->minor = VPE_MODULE_MINOR;
+
+out:
+	return v;
+}
+
+/* allocate a tc. At startup only tc0 is running, all other can be halted. */
+struct tc *alloc_tc(int index)
+{
+	struct tc *tc;
+
+	tc = kzalloc(sizeof(struct tc), GFP_KERNEL);
+	if (tc == NULL)
+		goto out;
+
+	INIT_LIST_HEAD(&tc->tc);
+	tc->index = index;
+
+	spin_lock(&vpecontrol.tc_list_lock);
+	list_add_tail(&tc->list, &vpecontrol.tc_list);
+	spin_unlock(&vpecontrol.tc_list_lock);
+
+out:
+	return tc;
+}
+
+/* clean up and free everything */
+void release_vpe(struct vpe *v)
+{
+	list_del(&v->list);
+	if (v->load_addr)
+		release_progmem(v->load_addr);
+	kfree(v);
+}
+
+/* Find some VPE program space */
+void *alloc_progmem(unsigned long len)
+{
+	void *addr;
+
+#ifdef CONFIG_MIPS_VPE_LOADER_TOM
+	/*
+	 * This means you must tell Linux to use less memory than you
+	 * physically have, for example by passing a mem= boot argument.
+	 */
+	addr = pfn_to_kaddr(max_low_pfn);
+	memset(addr, 0, len);
+#else
+	/* simple grab some mem for now */
+	addr = kzalloc(len, GFP_KERNEL);
+#endif
+
+	return addr;
+}
+
+void release_progmem(void *ptr)
+{
+#ifndef CONFIG_MIPS_VPE_LOADER_TOM
+	kfree(ptr);
+#endif
+}
+
+/* Update size with this section: return offset. */
+static long get_offset(unsigned long *size, Elf_Shdr *sechdr)
+{
+	long ret;
+
+	ret = ALIGN(*size, sechdr->sh_addralign ? : 1);
+	*size = ret + sechdr->sh_size;
+	return ret;
+}
+
+/* Lay out the SHF_ALLOC sections in a way not dissimilar to how ld
+   might -- code, read-only data, read-write data, small data.	Tally
+   sizes, and place the offsets into sh_entsize fields: high bit means it
+   belongs in init. */
+static void layout_sections(struct module *mod, const Elf_Ehdr *hdr,
+			    Elf_Shdr *sechdrs, const char *secstrings)
+{
+	static unsigned long const masks[][2] = {
+		/* NOTE: all executable code must be the first section
+		 * in this array; otherwise modify the text_size
+		 * finder in the two loops below */
+		{SHF_EXECINSTR | SHF_ALLOC, ARCH_SHF_SMALL},
+		{SHF_ALLOC, SHF_WRITE | ARCH_SHF_SMALL},
+		{SHF_WRITE | SHF_ALLOC, ARCH_SHF_SMALL},
+		{ARCH_SHF_SMALL | SHF_ALLOC, 0}
+	};
+	unsigned int m, i;
+
+	for (i = 0; i < hdr->e_shnum; i++)
+		sechdrs[i].sh_entsize = ~0UL;
+
+	for (m = 0; m < ARRAY_SIZE(masks); ++m) {
+		for (i = 0; i < hdr->e_shnum; ++i) {
+			Elf_Shdr *s = &sechdrs[i];
+
+			if ((s->sh_flags & masks[m][0]) != masks[m][0]
+			    || (s->sh_flags & masks[m][1])
+			    || s->sh_entsize != ~0UL)
+				continue;
+			s->sh_entsize =
+				get_offset((unsigned long *)&mod->core_layout.size, s);
+		}
+
+		if (m == 0)
+			mod->core_layout.text_size = mod->core_layout.size;
+
+	}
+}
+
+/* from module-elf32.c, but subverted a little */
+
+struct mips_hi16 {
+	struct mips_hi16 *next;
+	Elf32_Addr *addr;
+	Elf32_Addr value;
+};
+
+static struct mips_hi16 *mips_hi16_list;
+static unsigned int gp_offs, gp_addr;
+
+static int apply_r_mips_none(struct module *me, uint32_t *location,
+			     Elf32_Addr v)
+{
+	return 0;
+}
+
+static int apply_r_mips_gprel16(struct module *me, uint32_t *location,
+				Elf32_Addr v)
+{
+	int rel;
+
+	if (!(*location & 0xffff)) {
+		rel = (int)v - gp_addr;
+	} else {
+		/* .sbss + gp(relative) + offset */
+		/* kludge! */
+		rel =  (int)(short)((int)v + gp_offs +
+				    (int)(short)(*location & 0xffff) - gp_addr);
+	}
+
+	if ((rel > 32768) || (rel < -32768)) {
+		pr_debug("VPE loader: apply_r_mips_gprel16: relative address 0x%x out of range of gp register\n",
+			 rel);
+		return -ENOEXEC;
+	}
+
+	*location = (*location & 0xffff0000) | (rel & 0xffff);
+
+	return 0;
+}
+
+static int apply_r_mips_pc16(struct module *me, uint32_t *location,
+			     Elf32_Addr v)
+{
+	int rel;
+	rel = (((unsigned int)v - (unsigned int)location));
+	rel >>= 2; /* because the offset is in _instructions_ not bytes. */
+	rel -= 1;  /* and one instruction less due to the branch delay slot. */
+
+	if ((rel > 32768) || (rel < -32768)) {
+		pr_debug("VPE loader: apply_r_mips_pc16: relative address out of range 0x%x\n",
+			 rel);
+		return -ENOEXEC;
+	}
+
+	*location = (*location & 0xffff0000) | (rel & 0xffff);
+
+	return 0;
+}
+
+static int apply_r_mips_32(struct module *me, uint32_t *location,
+			   Elf32_Addr v)
+{
+	*location += v;
+
+	return 0;
+}
+
+static int apply_r_mips_26(struct module *me, uint32_t *location,
+			   Elf32_Addr v)
+{
+	if (v % 4) {
+		pr_debug("VPE loader: apply_r_mips_26: unaligned relocation\n");
+		return -ENOEXEC;
+	}
+
+/*
+ * Not desperately convinced this is a good check of an overflow condition
+ * anyway. But it gets in the way of handling undefined weak symbols which
+ * we want to set to zero.
+ * if ((v & 0xf0000000) != (((unsigned long)location + 4) & 0xf0000000)) {
+ * printk(KERN_ERR
+ * "module %s: relocation overflow\n",
+ * me->name);
+ * return -ENOEXEC;
+ * }
+ */
+
+	*location = (*location & ~0x03ffffff) |
+		((*location + (v >> 2)) & 0x03ffffff);
+	return 0;
+}
+
+static int apply_r_mips_hi16(struct module *me, uint32_t *location,
+			     Elf32_Addr v)
+{
+	struct mips_hi16 *n;
+
+	/*
+	 * We cannot relocate this one now because we don't know the value of
+	 * the carry we need to add.  Save the information, and let LO16 do the
+	 * actual relocation.
+	 */
+	n = kmalloc(sizeof(*n), GFP_KERNEL);
+	if (!n)
+		return -ENOMEM;
+
+	n->addr = location;
+	n->value = v;
+	n->next = mips_hi16_list;
+	mips_hi16_list = n;
+
+	return 0;
+}
+
+static int apply_r_mips_lo16(struct module *me, uint32_t *location,
+			     Elf32_Addr v)
+{
+	unsigned long insnlo = *location;
+	Elf32_Addr val, vallo;
+	struct mips_hi16 *l, *next;
+
+	/* Sign extend the addend we extract from the lo insn.	*/
+	vallo = ((insnlo & 0xffff) ^ 0x8000) - 0x8000;
+
+	if (mips_hi16_list != NULL) {
+
+		l = mips_hi16_list;
+		while (l != NULL) {
+			unsigned long insn;
+
+			/*
+			 * The value for the HI16 had best be the same.
+			 */
+			if (v != l->value) {
+				pr_debug("VPE loader: apply_r_mips_lo16/hi16: inconsistent value information\n");
+				goto out_free;
+			}
+
+			/*
+			 * Do the HI16 relocation.  Note that we actually don't
+			 * need to know anything about the LO16 itself, except
+			 * where to find the low 16 bits of the addend needed
+			 * by the LO16.
+			 */
+			insn = *l->addr;
+			val = ((insn & 0xffff) << 16) + vallo;
+			val += v;
+
+			/*
+			 * Account for the sign extension that will happen in
+			 * the low bits.
+			 */
+			val = ((val >> 16) + ((val & 0x8000) != 0)) & 0xffff;
+
+			insn = (insn & ~0xffff) | val;
+			*l->addr = insn;
+
+			next = l->next;
+			kfree(l);
+			l = next;
+		}
+
+		mips_hi16_list = NULL;
+	}
+
+	/*
+	 * Ok, we're done with the HI16 relocs.	 Now deal with the LO16.
+	 */
+	val = v + vallo;
+	insnlo = (insnlo & ~0xffff) | (val & 0xffff);
+	*location = insnlo;
+
+	return 0;
+
+out_free:
+	while (l != NULL) {
+		next = l->next;
+		kfree(l);
+		l = next;
+	}
+	mips_hi16_list = NULL;
+
+	return -ENOEXEC;
+}
+
+static int (*reloc_handlers[]) (struct module *me, uint32_t *location,
+				Elf32_Addr v) = {
+	[R_MIPS_NONE]	= apply_r_mips_none,
+	[R_MIPS_32]	= apply_r_mips_32,
+	[R_MIPS_26]	= apply_r_mips_26,
+	[R_MIPS_HI16]	= apply_r_mips_hi16,
+	[R_MIPS_LO16]	= apply_r_mips_lo16,
+	[R_MIPS_GPREL16] = apply_r_mips_gprel16,
+	[R_MIPS_PC16] = apply_r_mips_pc16
+};
+
+static char *rstrs[] = {
+	[R_MIPS_NONE]	= "MIPS_NONE",
+	[R_MIPS_32]	= "MIPS_32",
+	[R_MIPS_26]	= "MIPS_26",
+	[R_MIPS_HI16]	= "MIPS_HI16",
+	[R_MIPS_LO16]	= "MIPS_LO16",
+	[R_MIPS_GPREL16] = "MIPS_GPREL16",
+	[R_MIPS_PC16] = "MIPS_PC16"
+};
+
+static int apply_relocations(Elf32_Shdr *sechdrs,
+		      const char *strtab,
+		      unsigned int symindex,
+		      unsigned int relsec,
+		      struct module *me)
+{
+	Elf32_Rel *rel = (void *) sechdrs[relsec].sh_addr;
+	Elf32_Sym *sym;
+	uint32_t *location;
+	unsigned int i;
+	Elf32_Addr v;
+	int res;
+
+	for (i = 0; i < sechdrs[relsec].sh_size / sizeof(*rel); i++) {
+		Elf32_Word r_info = rel[i].r_info;
+
+		/* This is where to make the change */
+		location = (void *)sechdrs[sechdrs[relsec].sh_info].sh_addr
+			+ rel[i].r_offset;
+		/* This is the symbol it is referring to */
+		sym = (Elf32_Sym *)sechdrs[symindex].sh_addr
+			+ ELF32_R_SYM(r_info);
+
+		if (!sym->st_value) {
+			pr_debug("%s: undefined weak symbol %s\n",
+				 me->name, strtab + sym->st_name);
+			/* just print the warning, dont barf */
+		}
+
+		v = sym->st_value;
+
+		res = reloc_handlers[ELF32_R_TYPE(r_info)](me, location, v);
+		if (res) {
+			char *r = rstrs[ELF32_R_TYPE(r_info)];
+			pr_warn("VPE loader: .text+0x%x relocation type %s for symbol \"%s\" failed\n",
+				rel[i].r_offset, r ? r : "UNKNOWN",
+				strtab + sym->st_name);
+			return res;
+		}
+	}
+
+	return 0;
+}
+
+static inline void save_gp_address(unsigned int secbase, unsigned int rel)
+{
+	gp_addr = secbase + rel;
+	gp_offs = gp_addr - (secbase & 0xffff0000);
+}
+/* end module-elf32.c */
+
+/* Change all symbols so that sh_value encodes the pointer directly. */
+static void simplify_symbols(Elf_Shdr *sechdrs,
+			    unsigned int symindex,
+			    const char *strtab,
+			    const char *secstrings,
+			    unsigned int nsecs, struct module *mod)
+{
+	Elf_Sym *sym = (void *)sechdrs[symindex].sh_addr;
+	unsigned long secbase, bssbase = 0;
+	unsigned int i, n = sechdrs[symindex].sh_size / sizeof(Elf_Sym);
+	int size;
+
+	/* find the .bss section for COMMON symbols */
+	for (i = 0; i < nsecs; i++) {
+		if (strncmp(secstrings + sechdrs[i].sh_name, ".bss", 4) == 0) {
+			bssbase = sechdrs[i].sh_addr;
+			break;
+		}
+	}
+
+	for (i = 1; i < n; i++) {
+		switch (sym[i].st_shndx) {
+		case SHN_COMMON:
+			/* Allocate space for the symbol in the .bss section.
+			   st_value is currently size.
+			   We want it to have the address of the symbol. */
+
+			size = sym[i].st_value;
+			sym[i].st_value = bssbase;
+
+			bssbase += size;
+			break;
+
+		case SHN_ABS:
+			/* Don't need to do anything */
+			break;
+
+		case SHN_UNDEF:
+			/* ret = -ENOENT; */
+			break;
+
+		case SHN_MIPS_SCOMMON:
+			pr_debug("simplify_symbols: ignoring SHN_MIPS_SCOMMON symbol <%s> st_shndx %d\n",
+				 strtab + sym[i].st_name, sym[i].st_shndx);
+			/* .sbss section */
+			break;
+
+		default:
+			secbase = sechdrs[sym[i].st_shndx].sh_addr;
+
+			if (strncmp(strtab + sym[i].st_name, "_gp", 3) == 0)
+				save_gp_address(secbase, sym[i].st_value);
+
+			sym[i].st_value += secbase;
+			break;
+		}
+	}
+}
+
+#ifdef DEBUG_ELFLOADER
+static void dump_elfsymbols(Elf_Shdr *sechdrs, unsigned int symindex,
+			    const char *strtab, struct module *mod)
+{
+	Elf_Sym *sym = (void *)sechdrs[symindex].sh_addr;
+	unsigned int i, n = sechdrs[symindex].sh_size / sizeof(Elf_Sym);
+
+	pr_debug("dump_elfsymbols: n %d\n", n);
+	for (i = 1; i < n; i++) {
+		pr_debug(" i %d name <%s> 0x%x\n", i, strtab + sym[i].st_name,
+			 sym[i].st_value);
+	}
+}
+#endif
+
+static int find_vpe_symbols(struct vpe *v, Elf_Shdr *sechdrs,
+				      unsigned int symindex, const char *strtab,
+				      struct module *mod)
+{
+	Elf_Sym *sym = (void *)sechdrs[symindex].sh_addr;
+	unsigned int i, n = sechdrs[symindex].sh_size / sizeof(Elf_Sym);
+
+	for (i = 1; i < n; i++) {
+		if (strcmp(strtab + sym[i].st_name, "__start") == 0)
+			v->__start = sym[i].st_value;
+
+		if (strcmp(strtab + sym[i].st_name, "vpe_shared") == 0)
+			v->shared_ptr = (void *)sym[i].st_value;
+	}
+
+	if ((v->__start == 0) || (v->shared_ptr == NULL))
+		return -1;
+
+	return 0;
+}
+
+/*
+ * Allocates a VPE with some program code space(the load address), copies the
+ * contents of the program (p)buffer performing relocatations/etc, free's it
+ * when finished.
+ */
+static int vpe_elfload(struct vpe *v)
+{
+	Elf_Ehdr *hdr;
+	Elf_Shdr *sechdrs;
+	long err = 0;
+	char *secstrings, *strtab = NULL;
+	unsigned int len, i, symindex = 0, strindex = 0, relocate = 0;
+	struct module mod; /* so we can re-use the relocations code */
+
+	memset(&mod, 0, sizeof(struct module));
+	strcpy(mod.name, "VPE loader");
+
+	hdr = (Elf_Ehdr *) v->pbuffer;
+	len = v->plen;
+
+	/* Sanity checks against insmoding binaries or wrong arch,
+	   weird elf version */
+	if (memcmp(hdr->e_ident, ELFMAG, SELFMAG) != 0
+	    || (hdr->e_type != ET_REL && hdr->e_type != ET_EXEC)
+	    || !elf_check_arch(hdr)
+	    || hdr->e_shentsize != sizeof(*sechdrs)) {
+		pr_warn("VPE loader: program wrong arch or weird elf version\n");
+
+		return -ENOEXEC;
+	}
+
+	if (hdr->e_type == ET_REL)
+		relocate = 1;
+
+	if (len < hdr->e_shoff + hdr->e_shnum * sizeof(Elf_Shdr)) {
+		pr_err("VPE loader: program length %u truncated\n", len);
+
+		return -ENOEXEC;
+	}
+
+	/* Convenience variables */
+	sechdrs = (void *)hdr + hdr->e_shoff;
+	secstrings = (void *)hdr + sechdrs[hdr->e_shstrndx].sh_offset;
+	sechdrs[0].sh_addr = 0;
+
+	/* And these should exist, but gcc whinges if we don't init them */
+	symindex = strindex = 0;
+
+	if (relocate) {
+		for (i = 1; i < hdr->e_shnum; i++) {
+			if ((sechdrs[i].sh_type != SHT_NOBITS) &&
+			    (len < sechdrs[i].sh_offset + sechdrs[i].sh_size)) {
+				pr_err("VPE program length %u truncated\n",
+				       len);
+				return -ENOEXEC;
+			}
+
+			/* Mark all sections sh_addr with their address in the
+			   temporary image. */
+			sechdrs[i].sh_addr = (size_t) hdr +
+				sechdrs[i].sh_offset;
+
+			/* Internal symbols and strings. */
+			if (sechdrs[i].sh_type == SHT_SYMTAB) {
+				symindex = i;
+				strindex = sechdrs[i].sh_link;
+				strtab = (char *)hdr +
+					sechdrs[strindex].sh_offset;
+			}
+		}
+		layout_sections(&mod, hdr, sechdrs, secstrings);
+	}
+
+	v->load_addr = alloc_progmem(mod.core_layout.size);
+	if (!v->load_addr)
+		return -ENOMEM;
+
+	pr_info("VPE loader: loading to %p\n", v->load_addr);
+
+	if (relocate) {
+		for (i = 0; i < hdr->e_shnum; i++) {
+			void *dest;
+
+			if (!(sechdrs[i].sh_flags & SHF_ALLOC))
+				continue;
+
+			dest = v->load_addr + sechdrs[i].sh_entsize;
+
+			if (sechdrs[i].sh_type != SHT_NOBITS)
+				memcpy(dest, (void *)sechdrs[i].sh_addr,
+				       sechdrs[i].sh_size);
+			/* Update sh_addr to point to copy in image. */
+			sechdrs[i].sh_addr = (unsigned long)dest;
+
+			pr_debug(" section sh_name %s sh_addr 0x%x\n",
+				 secstrings + sechdrs[i].sh_name,
+				 sechdrs[i].sh_addr);
+		}
+
+		/* Fix up syms, so that st_value is a pointer to location. */
+		simplify_symbols(sechdrs, symindex, strtab, secstrings,
+				 hdr->e_shnum, &mod);
+
+		/* Now do relocations. */
+		for (i = 1; i < hdr->e_shnum; i++) {
+			const char *strtab = (char *)sechdrs[strindex].sh_addr;
+			unsigned int info = sechdrs[i].sh_info;
+
+			/* Not a valid relocation section? */
+			if (info >= hdr->e_shnum)
+				continue;
+
+			/* Don't bother with non-allocated sections */
+			if (!(sechdrs[info].sh_flags & SHF_ALLOC))
+				continue;
+
+			if (sechdrs[i].sh_type == SHT_REL)
+				err = apply_relocations(sechdrs, strtab,
+							symindex, i, &mod);
+			else if (sechdrs[i].sh_type == SHT_RELA)
+				err = apply_relocate_add(sechdrs, strtab,
+							 symindex, i, &mod);
+			if (err < 0)
+				return err;
+
+		}
+	} else {
+		struct elf_phdr *phdr = (struct elf_phdr *)
+						((char *)hdr + hdr->e_phoff);
+
+		for (i = 0; i < hdr->e_phnum; i++) {
+			if (phdr->p_type == PT_LOAD) {
+				memcpy((void *)phdr->p_paddr,
+				       (char *)hdr + phdr->p_offset,
+				       phdr->p_filesz);
+				memset((void *)phdr->p_paddr + phdr->p_filesz,
+				       0, phdr->p_memsz - phdr->p_filesz);
+		    }
+		    phdr++;
+		}
+
+		for (i = 0; i < hdr->e_shnum; i++) {
+			/* Internal symbols and strings. */
+			if (sechdrs[i].sh_type == SHT_SYMTAB) {
+				symindex = i;
+				strindex = sechdrs[i].sh_link;
+				strtab = (char *)hdr +
+					sechdrs[strindex].sh_offset;
+
+				/*
+				 * mark symtab's address for when we try
+				 * to find the magic symbols
+				 */
+				sechdrs[i].sh_addr = (size_t) hdr +
+					sechdrs[i].sh_offset;
+			}
+		}
+	}
+
+	/* make sure it's physically written out */
+	flush_icache_range((unsigned long)v->load_addr,
+			   (unsigned long)v->load_addr + v->len);
+
+	if ((find_vpe_symbols(v, sechdrs, symindex, strtab, &mod)) < 0) {
+		if (v->__start == 0) {
+			pr_warn("VPE loader: program does not contain a __start symbol\n");
+			return -ENOEXEC;
+		}
+
+		if (v->shared_ptr == NULL)
+			pr_warn("VPE loader: program does not contain vpe_shared symbol.\n"
+				" Unable to use AMVP (AP/SP) facilities.\n");
+	}
+
+	pr_info(" elf loaded\n");
+	return 0;
+}
+
+/* checks VPE is unused and gets ready to load program	*/
+static int vpe_open(struct inode *inode, struct file *filp)
+{
+	enum vpe_state state;
+	struct vpe_notifications *notifier;
+	struct vpe *v;
+
+	if (VPE_MODULE_MINOR != iminor(inode)) {
+		/* assume only 1 device at the moment. */
+		pr_warn("VPE loader: only vpe1 is supported\n");
+
+		return -ENODEV;
+	}
+
+	v = get_vpe(aprp_cpu_index());
+	if (v == NULL) {
+		pr_warn("VPE loader: unable to get vpe\n");
+
+		return -ENODEV;
+	}
+
+	state = xchg(&v->state, VPE_STATE_INUSE);
+	if (state != VPE_STATE_UNUSED) {
+		pr_debug("VPE loader: tc in use dumping regs\n");
+
+		list_for_each_entry(notifier, &v->notify, list)
+			notifier->stop(aprp_cpu_index());
+
+		release_progmem(v->load_addr);
+		cleanup_tc(get_tc(aprp_cpu_index()));
+	}
+
+	/* this of-course trashes what was there before... */
+	v->pbuffer = vmalloc(P_SIZE);
+	if (!v->pbuffer) {
+		pr_warn("VPE loader: unable to allocate memory\n");
+		return -ENOMEM;
+	}
+	v->plen = P_SIZE;
+	v->load_addr = NULL;
+	v->len = 0;
+	v->shared_ptr = NULL;
+	v->__start = 0;
+
+	return 0;
+}
+
+static int vpe_release(struct inode *inode, struct file *filp)
+{
+#if defined(CONFIG_MIPS_VPE_LOADER_MT) || defined(CONFIG_MIPS_VPE_LOADER_CMP)
+	struct vpe *v;
+	Elf_Ehdr *hdr;
+	int ret = 0;
+
+	v = get_vpe(aprp_cpu_index());
+	if (v == NULL)
+		return -ENODEV;
+
+	hdr = (Elf_Ehdr *) v->pbuffer;
+	if (memcmp(hdr->e_ident, ELFMAG, SELFMAG) == 0) {
+		if (vpe_elfload(v) >= 0) {
+			vpe_run(v);
+		} else {
+			pr_warn("VPE loader: ELF load failed.\n");
+			ret = -ENOEXEC;
+		}
+	} else {
+		pr_warn("VPE loader: only elf files are supported\n");
+		ret = -ENOEXEC;
+	}
+
+	/* It's good to be able to run the SP and if it chokes have a look at
+	   the /dev/rt?. But if we reset the pointer to the shared struct we
+	   lose what has happened. So perhaps if garbage is sent to the vpe
+	   device, use it as a trigger for the reset. Hopefully a nice
+	   executable will be along shortly. */
+	if (ret < 0)
+		v->shared_ptr = NULL;
+
+	vfree(v->pbuffer);
+	v->plen = 0;
+
+	return ret;
+#else
+	pr_warn("VPE loader: ELF load failed.\n");
+	return -ENOEXEC;
+#endif
+}
+
+static ssize_t vpe_write(struct file *file, const char __user *buffer,
+			 size_t count, loff_t *ppos)
+{
+	size_t ret = count;
+	struct vpe *v;
+
+	if (iminor(file_inode(file)) != VPE_MODULE_MINOR)
+		return -ENODEV;
+
+	v = get_vpe(aprp_cpu_index());
+
+	if (v == NULL)
+		return -ENODEV;
+
+	if ((count + v->len) > v->plen) {
+		pr_warn("VPE loader: elf size too big. Perhaps strip unneeded symbols\n");
+		return -ENOMEM;
+	}
+
+	count -= copy_from_user(v->pbuffer + v->len, buffer, count);
+	if (!count)
+		return -EFAULT;
+
+	v->len += count;
+	return ret;
+}
+
+const struct file_operations vpe_fops = {
+	.owner = THIS_MODULE,
+	.open = vpe_open,
+	.release = vpe_release,
+	.write = vpe_write,
+	.llseek = noop_llseek,
+};
+
+void *vpe_get_shared(int index)
+{
+	struct vpe *v = get_vpe(index);
+
+	if (v == NULL)
+		return NULL;
+
+	return v->shared_ptr;
+}
+EXPORT_SYMBOL(vpe_get_shared);
+
+int vpe_notify(int index, struct vpe_notifications *notify)
+{
+	struct vpe *v = get_vpe(index);
+
+	if (v == NULL)
+		return -1;
+
+	list_add(&notify->list, &v->notify);
+	return 0;
+}
+EXPORT_SYMBOL(vpe_notify);
+
+module_init(vpe_module_init);
+module_exit(vpe_module_exit);
+MODULE_DESCRIPTION("MIPS VPE Loader");
+MODULE_AUTHOR("Elizabeth Oldham, MIPS Technologies, Inc.");
+MODULE_LICENSE("GPL");
diff --git a/arch/mips/kernel/watch.c b/arch/mips/kernel/watch.c
new file mode 100644
index 000000000..c9263b95c
--- /dev/null
+++ b/arch/mips/kernel/watch.c
@@ -0,0 +1,211 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 David Daney
+ */
+
+#include <linux/sched.h>
+
+#include <asm/processor.h>
+#include <asm/watch.h>
+
+/*
+ * Install the watch registers for the current thread.	A maximum of
+ * four registers are installed although the machine may have more.
+ */
+void mips_install_watch_registers(struct task_struct *t)
+{
+	struct mips3264_watch_reg_state *watches = &t->thread.watch.mips3264;
+	unsigned int watchhi = MIPS_WATCHHI_G |		/* Trap all ASIDs */
+			       MIPS_WATCHHI_IRW;	/* Clear result bits */
+
+	switch (current_cpu_data.watch_reg_use_cnt) {
+	default:
+		BUG();
+	case 4:
+		write_c0_watchlo3(watches->watchlo[3]);
+		write_c0_watchhi3(watchhi | watches->watchhi[3]);
+		fallthrough;
+	case 3:
+		write_c0_watchlo2(watches->watchlo[2]);
+		write_c0_watchhi2(watchhi | watches->watchhi[2]);
+		fallthrough;
+	case 2:
+		write_c0_watchlo1(watches->watchlo[1]);
+		write_c0_watchhi1(watchhi | watches->watchhi[1]);
+		fallthrough;
+	case 1:
+		write_c0_watchlo0(watches->watchlo[0]);
+		write_c0_watchhi0(watchhi | watches->watchhi[0]);
+	}
+}
+
+/*
+ * Read back the watchhi registers so the user space debugger has
+ * access to the I, R, and W bits.  A maximum of four registers are
+ * read although the machine may have more.
+ */
+void mips_read_watch_registers(void)
+{
+	struct mips3264_watch_reg_state *watches =
+		&current->thread.watch.mips3264;
+	unsigned int watchhi_mask = MIPS_WATCHHI_MASK | MIPS_WATCHHI_IRW;
+
+	switch (current_cpu_data.watch_reg_use_cnt) {
+	default:
+		BUG();
+	case 4:
+		watches->watchhi[3] = (read_c0_watchhi3() & watchhi_mask);
+		fallthrough;
+	case 3:
+		watches->watchhi[2] = (read_c0_watchhi2() & watchhi_mask);
+		fallthrough;
+	case 2:
+		watches->watchhi[1] = (read_c0_watchhi1() & watchhi_mask);
+		fallthrough;
+	case 1:
+		watches->watchhi[0] = (read_c0_watchhi0() & watchhi_mask);
+	}
+	if (current_cpu_data.watch_reg_use_cnt == 1 &&
+	    (watches->watchhi[0] & MIPS_WATCHHI_IRW) == 0) {
+		/* Pathological case of release 1 architecture that
+		 * doesn't set the condition bits.  We assume that
+		 * since we got here, the watch condition was met and
+		 * signal that the conditions requested in watchlo
+		 * were met.  */
+		watches->watchhi[0] |= (watches->watchlo[0] & MIPS_WATCHHI_IRW);
+	}
+ }
+
+/*
+ * Disable all watch registers.	 Although only four registers are
+ * installed, all are cleared to eliminate the possibility of endless
+ * looping in the watch handler.
+ */
+void mips_clear_watch_registers(void)
+{
+	switch (current_cpu_data.watch_reg_count) {
+	default:
+		BUG();
+	case 8:
+		write_c0_watchlo7(0);
+		fallthrough;
+	case 7:
+		write_c0_watchlo6(0);
+		fallthrough;
+	case 6:
+		write_c0_watchlo5(0);
+		fallthrough;
+	case 5:
+		write_c0_watchlo4(0);
+		fallthrough;
+	case 4:
+		write_c0_watchlo3(0);
+		fallthrough;
+	case 3:
+		write_c0_watchlo2(0);
+		fallthrough;
+	case 2:
+		write_c0_watchlo1(0);
+		fallthrough;
+	case 1:
+		write_c0_watchlo0(0);
+	}
+}
+
+void mips_probe_watch_registers(struct cpuinfo_mips *c)
+{
+	unsigned int t;
+
+	if ((c->options & MIPS_CPU_WATCH) == 0)
+		return;
+	/*
+	 * Check which of the I,R and W bits are supported, then
+	 * disable the register.
+	 */
+	write_c0_watchlo0(MIPS_WATCHLO_IRW);
+	back_to_back_c0_hazard();
+	t = read_c0_watchlo0();
+	write_c0_watchlo0(0);
+	c->watch_reg_masks[0] = t & MIPS_WATCHLO_IRW;
+
+	/* Write the mask bits and read them back to determine which
+	 * can be used. */
+	c->watch_reg_count = 1;
+	c->watch_reg_use_cnt = 1;
+	t = read_c0_watchhi0();
+	write_c0_watchhi0(t | MIPS_WATCHHI_MASK);
+	back_to_back_c0_hazard();
+	t = read_c0_watchhi0();
+	c->watch_reg_masks[0] |= (t & MIPS_WATCHHI_MASK);
+	if ((t & MIPS_WATCHHI_M) == 0)
+		return;
+
+	write_c0_watchlo1(MIPS_WATCHLO_IRW);
+	back_to_back_c0_hazard();
+	t = read_c0_watchlo1();
+	write_c0_watchlo1(0);
+	c->watch_reg_masks[1] = t & MIPS_WATCHLO_IRW;
+
+	c->watch_reg_count = 2;
+	c->watch_reg_use_cnt = 2;
+	t = read_c0_watchhi1();
+	write_c0_watchhi1(t | MIPS_WATCHHI_MASK);
+	back_to_back_c0_hazard();
+	t = read_c0_watchhi1();
+	c->watch_reg_masks[1] |= (t & MIPS_WATCHHI_MASK);
+	if ((t & MIPS_WATCHHI_M) == 0)
+		return;
+
+	write_c0_watchlo2(MIPS_WATCHLO_IRW);
+	back_to_back_c0_hazard();
+	t = read_c0_watchlo2();
+	write_c0_watchlo2(0);
+	c->watch_reg_masks[2] = t & MIPS_WATCHLO_IRW;
+
+	c->watch_reg_count = 3;
+	c->watch_reg_use_cnt = 3;
+	t = read_c0_watchhi2();
+	write_c0_watchhi2(t | MIPS_WATCHHI_MASK);
+	back_to_back_c0_hazard();
+	t = read_c0_watchhi2();
+	c->watch_reg_masks[2] |= (t & MIPS_WATCHHI_MASK);
+	if ((t & MIPS_WATCHHI_M) == 0)
+		return;
+
+	write_c0_watchlo3(MIPS_WATCHLO_IRW);
+	back_to_back_c0_hazard();
+	t = read_c0_watchlo3();
+	write_c0_watchlo3(0);
+	c->watch_reg_masks[3] = t & MIPS_WATCHLO_IRW;
+
+	c->watch_reg_count = 4;
+	c->watch_reg_use_cnt = 4;
+	t = read_c0_watchhi3();
+	write_c0_watchhi3(t | MIPS_WATCHHI_MASK);
+	back_to_back_c0_hazard();
+	t = read_c0_watchhi3();
+	c->watch_reg_masks[3] |= (t & MIPS_WATCHHI_MASK);
+	if ((t & MIPS_WATCHHI_M) == 0)
+		return;
+
+	/* We use at most 4, but probe and report up to 8. */
+	c->watch_reg_count = 5;
+	t = read_c0_watchhi4();
+	if ((t & MIPS_WATCHHI_M) == 0)
+		return;
+
+	c->watch_reg_count = 6;
+	t = read_c0_watchhi5();
+	if ((t & MIPS_WATCHHI_M) == 0)
+		return;
+
+	c->watch_reg_count = 7;
+	t = read_c0_watchhi6();
+	if ((t & MIPS_WATCHHI_M) == 0)
+		return;
+
+	c->watch_reg_count = 8;
+}
diff --git a/arch/mips/kvm/Kconfig b/arch/mips/kvm/Kconfig
new file mode 100644
index 000000000..91d197bee
--- /dev/null
+++ b/arch/mips/kvm/Kconfig
@@ -0,0 +1,44 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# KVM configuration
+#
+source "virt/kvm/Kconfig"
+
+menuconfig VIRTUALIZATION
+	bool "Virtualization"
+	help
+	  Say Y here to get to see options for using your Linux host to run
+	  other operating systems inside virtual machines (guests).
+	  This option alone does not add any kernel code.
+
+	  If you say N, all options in this submenu will be skipped and disabled.
+
+if VIRTUALIZATION
+
+config KVM
+	tristate "Kernel-based Virtual Machine (KVM) support"
+	depends on HAVE_KVM
+	depends on MIPS_FP_SUPPORT
+	select EXPORT_UASM
+	select PREEMPT_NOTIFIERS
+	select KVM_GENERIC_DIRTYLOG_READ_PROTECT
+	select HAVE_KVM_EVENTFD
+	select HAVE_KVM_VCPU_ASYNC_IOCTL
+	select KVM_MMIO
+	select MMU_NOTIFIER
+	select SRCU
+	select INTERVAL_TREE
+	help
+	  Support for hosting Guest kernels.
+
+config KVM_MIPS_DEBUG_COP0_COUNTERS
+	bool "Maintain counters for COP0 accesses"
+	depends on KVM
+	help
+	  Maintain statistics for Guest COP0 accesses.
+	  A histogram of COP0 accesses is printed when the VM is
+	  shutdown.
+
+	  If unsure, say N.
+
+endif # VIRTUALIZATION
diff --git a/arch/mips/kvm/Makefile b/arch/mips/kvm/Makefile
new file mode 100644
index 000000000..21ff75bcd
--- /dev/null
+++ b/arch/mips/kvm/Makefile
@@ -0,0 +1,20 @@
+# SPDX-License-Identifier: GPL-2.0
+# Makefile for KVM support for MIPS
+#
+
+include $(srctree)/virt/kvm/Makefile.kvm
+
+ccflags-y += -Ivirt/kvm -Iarch/mips/kvm
+
+kvm-$(CONFIG_CPU_HAS_MSA) += msa.o
+
+kvm-y +=    mips.o emulate.o entry.o \
+	    interrupt.o stats.o \
+	    fpu.o
+kvm-y += hypcall.o
+kvm-y += mmu.o
+kvm-$(CONFIG_CPU_LOONGSON64) += loongson_ipi.o
+
+kvm-y		+= vz.o
+obj-$(CONFIG_KVM)	+= kvm.o
+obj-y			+= callback.o tlb.o
diff --git a/arch/mips/kvm/callback.c b/arch/mips/kvm/callback.c
new file mode 100644
index 000000000..d88aa2173
--- /dev/null
+++ b/arch/mips/kvm/callback.c
@@ -0,0 +1,14 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2012  MIPS Technologies, Inc.  All rights reserved.
+ * Authors: Yann Le Du <ledu@kymasys.com>
+ */
+
+#include <linux/export.h>
+#include <linux/kvm_host.h>
+
+struct kvm_mips_callbacks *kvm_mips_callbacks;
+EXPORT_SYMBOL_GPL(kvm_mips_callbacks);
diff --git a/arch/mips/kvm/emulate.c b/arch/mips/kvm/emulate.c
new file mode 100644
index 000000000..e64372b8f
--- /dev/null
+++ b/arch/mips/kvm/emulate.c
@@ -0,0 +1,1650 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * KVM/MIPS: Instruction/Exception emulation
+ *
+ * Copyright (C) 2012  MIPS Technologies, Inc.  All rights reserved.
+ * Authors: Sanjay Lal <sanjayl@kymasys.com>
+ */
+
+#include <linux/errno.h>
+#include <linux/err.h>
+#include <linux/ktime.h>
+#include <linux/kvm_host.h>
+#include <linux/vmalloc.h>
+#include <linux/fs.h>
+#include <linux/memblock.h>
+#include <linux/random.h>
+#include <asm/page.h>
+#include <asm/cacheflush.h>
+#include <asm/cacheops.h>
+#include <asm/cpu-info.h>
+#include <asm/mmu_context.h>
+#include <asm/tlbflush.h>
+#include <asm/inst.h>
+
+#undef CONFIG_MIPS_MT
+#include <asm/r4kcache.h>
+#define CONFIG_MIPS_MT
+
+#include "interrupt.h"
+
+#include "trace.h"
+
+/*
+ * Compute the return address and do emulate branch simulation, if required.
+ * This function should be called only in branch delay slot active.
+ */
+static int kvm_compute_return_epc(struct kvm_vcpu *vcpu, unsigned long instpc,
+				  unsigned long *out)
+{
+	unsigned int dspcontrol;
+	union mips_instruction insn;
+	struct kvm_vcpu_arch *arch = &vcpu->arch;
+	long epc = instpc;
+	long nextpc;
+	int err;
+
+	if (epc & 3) {
+		kvm_err("%s: unaligned epc\n", __func__);
+		return -EINVAL;
+	}
+
+	/* Read the instruction */
+	err = kvm_get_badinstrp((u32 *)epc, vcpu, &insn.word);
+	if (err)
+		return err;
+
+	switch (insn.i_format.opcode) {
+		/* jr and jalr are in r_format format. */
+	case spec_op:
+		switch (insn.r_format.func) {
+		case jalr_op:
+			arch->gprs[insn.r_format.rd] = epc + 8;
+			fallthrough;
+		case jr_op:
+			nextpc = arch->gprs[insn.r_format.rs];
+			break;
+		default:
+			return -EINVAL;
+		}
+		break;
+
+		/*
+		 * This group contains:
+		 * bltz_op, bgez_op, bltzl_op, bgezl_op,
+		 * bltzal_op, bgezal_op, bltzall_op, bgezall_op.
+		 */
+	case bcond_op:
+		switch (insn.i_format.rt) {
+		case bltz_op:
+		case bltzl_op:
+			if ((long)arch->gprs[insn.i_format.rs] < 0)
+				epc = epc + 4 + (insn.i_format.simmediate << 2);
+			else
+				epc += 8;
+			nextpc = epc;
+			break;
+
+		case bgez_op:
+		case bgezl_op:
+			if ((long)arch->gprs[insn.i_format.rs] >= 0)
+				epc = epc + 4 + (insn.i_format.simmediate << 2);
+			else
+				epc += 8;
+			nextpc = epc;
+			break;
+
+		case bltzal_op:
+		case bltzall_op:
+			arch->gprs[31] = epc + 8;
+			if ((long)arch->gprs[insn.i_format.rs] < 0)
+				epc = epc + 4 + (insn.i_format.simmediate << 2);
+			else
+				epc += 8;
+			nextpc = epc;
+			break;
+
+		case bgezal_op:
+		case bgezall_op:
+			arch->gprs[31] = epc + 8;
+			if ((long)arch->gprs[insn.i_format.rs] >= 0)
+				epc = epc + 4 + (insn.i_format.simmediate << 2);
+			else
+				epc += 8;
+			nextpc = epc;
+			break;
+		case bposge32_op:
+			if (!cpu_has_dsp) {
+				kvm_err("%s: DSP branch but not DSP ASE\n",
+					__func__);
+				return -EINVAL;
+			}
+
+			dspcontrol = rddsp(0x01);
+
+			if (dspcontrol >= 32)
+				epc = epc + 4 + (insn.i_format.simmediate << 2);
+			else
+				epc += 8;
+			nextpc = epc;
+			break;
+		default:
+			return -EINVAL;
+		}
+		break;
+
+		/* These are unconditional and in j_format. */
+	case jal_op:
+		arch->gprs[31] = instpc + 8;
+		fallthrough;
+	case j_op:
+		epc += 4;
+		epc >>= 28;
+		epc <<= 28;
+		epc |= (insn.j_format.target << 2);
+		nextpc = epc;
+		break;
+
+		/* These are conditional and in i_format. */
+	case beq_op:
+	case beql_op:
+		if (arch->gprs[insn.i_format.rs] ==
+		    arch->gprs[insn.i_format.rt])
+			epc = epc + 4 + (insn.i_format.simmediate << 2);
+		else
+			epc += 8;
+		nextpc = epc;
+		break;
+
+	case bne_op:
+	case bnel_op:
+		if (arch->gprs[insn.i_format.rs] !=
+		    arch->gprs[insn.i_format.rt])
+			epc = epc + 4 + (insn.i_format.simmediate << 2);
+		else
+			epc += 8;
+		nextpc = epc;
+		break;
+
+	case blez_op:	/* POP06 */
+#ifndef CONFIG_CPU_MIPSR6
+	case blezl_op:	/* removed in R6 */
+#endif
+		if (insn.i_format.rt != 0)
+			goto compact_branch;
+		if ((long)arch->gprs[insn.i_format.rs] <= 0)
+			epc = epc + 4 + (insn.i_format.simmediate << 2);
+		else
+			epc += 8;
+		nextpc = epc;
+		break;
+
+	case bgtz_op:	/* POP07 */
+#ifndef CONFIG_CPU_MIPSR6
+	case bgtzl_op:	/* removed in R6 */
+#endif
+		if (insn.i_format.rt != 0)
+			goto compact_branch;
+		if ((long)arch->gprs[insn.i_format.rs] > 0)
+			epc = epc + 4 + (insn.i_format.simmediate << 2);
+		else
+			epc += 8;
+		nextpc = epc;
+		break;
+
+		/* And now the FPA/cp1 branch instructions. */
+	case cop1_op:
+		kvm_err("%s: unsupported cop1_op\n", __func__);
+		return -EINVAL;
+
+#ifdef CONFIG_CPU_MIPSR6
+	/* R6 added the following compact branches with forbidden slots */
+	case blezl_op:	/* POP26 */
+	case bgtzl_op:	/* POP27 */
+		/* only rt == 0 isn't compact branch */
+		if (insn.i_format.rt != 0)
+			goto compact_branch;
+		return -EINVAL;
+	case pop10_op:
+	case pop30_op:
+		/* only rs == rt == 0 is reserved, rest are compact branches */
+		if (insn.i_format.rs != 0 || insn.i_format.rt != 0)
+			goto compact_branch;
+		return -EINVAL;
+	case pop66_op:
+	case pop76_op:
+		/* only rs == 0 isn't compact branch */
+		if (insn.i_format.rs != 0)
+			goto compact_branch;
+		return -EINVAL;
+compact_branch:
+		/*
+		 * If we've hit an exception on the forbidden slot, then
+		 * the branch must not have been taken.
+		 */
+		epc += 8;
+		nextpc = epc;
+		break;
+#else
+compact_branch:
+		/* Fall through - Compact branches not supported before R6 */
+#endif
+	default:
+		return -EINVAL;
+	}
+
+	*out = nextpc;
+	return 0;
+}
+
+enum emulation_result update_pc(struct kvm_vcpu *vcpu, u32 cause)
+{
+	int err;
+
+	if (cause & CAUSEF_BD) {
+		err = kvm_compute_return_epc(vcpu, vcpu->arch.pc,
+					     &vcpu->arch.pc);
+		if (err)
+			return EMULATE_FAIL;
+	} else {
+		vcpu->arch.pc += 4;
+	}
+
+	kvm_debug("update_pc(): New PC: %#lx\n", vcpu->arch.pc);
+
+	return EMULATE_DONE;
+}
+
+/**
+ * kvm_get_badinstr() - Get bad instruction encoding.
+ * @opc:	Guest pointer to faulting instruction.
+ * @vcpu:	KVM VCPU information.
+ *
+ * Gets the instruction encoding of the faulting instruction, using the saved
+ * BadInstr register value if it exists, otherwise falling back to reading guest
+ * memory at @opc.
+ *
+ * Returns:	The instruction encoding of the faulting instruction.
+ */
+int kvm_get_badinstr(u32 *opc, struct kvm_vcpu *vcpu, u32 *out)
+{
+	if (cpu_has_badinstr) {
+		*out = vcpu->arch.host_cp0_badinstr;
+		return 0;
+	} else {
+		WARN_ONCE(1, "CPU doesn't have BadInstr register\n");
+		return -EINVAL;
+	}
+}
+
+/**
+ * kvm_get_badinstrp() - Get bad prior instruction encoding.
+ * @opc:	Guest pointer to prior faulting instruction.
+ * @vcpu:	KVM VCPU information.
+ *
+ * Gets the instruction encoding of the prior faulting instruction (the branch
+ * containing the delay slot which faulted), using the saved BadInstrP register
+ * value if it exists, otherwise falling back to reading guest memory at @opc.
+ *
+ * Returns:	The instruction encoding of the prior faulting instruction.
+ */
+int kvm_get_badinstrp(u32 *opc, struct kvm_vcpu *vcpu, u32 *out)
+{
+	if (cpu_has_badinstrp) {
+		*out = vcpu->arch.host_cp0_badinstrp;
+		return 0;
+	} else {
+		WARN_ONCE(1, "CPU doesn't have BadInstrp register\n");
+		return -EINVAL;
+	}
+}
+
+/**
+ * kvm_mips_count_disabled() - Find whether the CP0_Count timer is disabled.
+ * @vcpu:	Virtual CPU.
+ *
+ * Returns:	1 if the CP0_Count timer is disabled by either the guest
+ *		CP0_Cause.DC bit or the count_ctl.DC bit.
+ *		0 otherwise (in which case CP0_Count timer is running).
+ */
+int kvm_mips_count_disabled(struct kvm_vcpu *vcpu)
+{
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
+
+	return	(vcpu->arch.count_ctl & KVM_REG_MIPS_COUNT_CTL_DC) ||
+		(kvm_read_c0_guest_cause(cop0) & CAUSEF_DC);
+}
+
+/**
+ * kvm_mips_ktime_to_count() - Scale ktime_t to a 32-bit count.
+ *
+ * Caches the dynamic nanosecond bias in vcpu->arch.count_dyn_bias.
+ *
+ * Assumes !kvm_mips_count_disabled(@vcpu) (guest CP0_Count timer is running).
+ */
+static u32 kvm_mips_ktime_to_count(struct kvm_vcpu *vcpu, ktime_t now)
+{
+	s64 now_ns, periods;
+	u64 delta;
+
+	now_ns = ktime_to_ns(now);
+	delta = now_ns + vcpu->arch.count_dyn_bias;
+
+	if (delta >= vcpu->arch.count_period) {
+		/* If delta is out of safe range the bias needs adjusting */
+		periods = div64_s64(now_ns, vcpu->arch.count_period);
+		vcpu->arch.count_dyn_bias = -periods * vcpu->arch.count_period;
+		/* Recalculate delta with new bias */
+		delta = now_ns + vcpu->arch.count_dyn_bias;
+	}
+
+	/*
+	 * We've ensured that:
+	 *   delta < count_period
+	 *
+	 * Therefore the intermediate delta*count_hz will never overflow since
+	 * at the boundary condition:
+	 *   delta = count_period
+	 *   delta = NSEC_PER_SEC * 2^32 / count_hz
+	 *   delta * count_hz = NSEC_PER_SEC * 2^32
+	 */
+	return div_u64(delta * vcpu->arch.count_hz, NSEC_PER_SEC);
+}
+
+/**
+ * kvm_mips_count_time() - Get effective current time.
+ * @vcpu:	Virtual CPU.
+ *
+ * Get effective monotonic ktime. This is usually a straightforward ktime_get(),
+ * except when the master disable bit is set in count_ctl, in which case it is
+ * count_resume, i.e. the time that the count was disabled.
+ *
+ * Returns:	Effective monotonic ktime for CP0_Count.
+ */
+static inline ktime_t kvm_mips_count_time(struct kvm_vcpu *vcpu)
+{
+	if (unlikely(vcpu->arch.count_ctl & KVM_REG_MIPS_COUNT_CTL_DC))
+		return vcpu->arch.count_resume;
+
+	return ktime_get();
+}
+
+/**
+ * kvm_mips_read_count_running() - Read the current count value as if running.
+ * @vcpu:	Virtual CPU.
+ * @now:	Kernel time to read CP0_Count at.
+ *
+ * Returns the current guest CP0_Count register at time @now and handles if the
+ * timer interrupt is pending and hasn't been handled yet.
+ *
+ * Returns:	The current value of the guest CP0_Count register.
+ */
+static u32 kvm_mips_read_count_running(struct kvm_vcpu *vcpu, ktime_t now)
+{
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
+	ktime_t expires, threshold;
+	u32 count, compare;
+	int running;
+
+	/* Calculate the biased and scaled guest CP0_Count */
+	count = vcpu->arch.count_bias + kvm_mips_ktime_to_count(vcpu, now);
+	compare = kvm_read_c0_guest_compare(cop0);
+
+	/*
+	 * Find whether CP0_Count has reached the closest timer interrupt. If
+	 * not, we shouldn't inject it.
+	 */
+	if ((s32)(count - compare) < 0)
+		return count;
+
+	/*
+	 * The CP0_Count we're going to return has already reached the closest
+	 * timer interrupt. Quickly check if it really is a new interrupt by
+	 * looking at whether the interval until the hrtimer expiry time is
+	 * less than 1/4 of the timer period.
+	 */
+	expires = hrtimer_get_expires(&vcpu->arch.comparecount_timer);
+	threshold = ktime_add_ns(now, vcpu->arch.count_period / 4);
+	if (ktime_before(expires, threshold)) {
+		/*
+		 * Cancel it while we handle it so there's no chance of
+		 * interference with the timeout handler.
+		 */
+		running = hrtimer_cancel(&vcpu->arch.comparecount_timer);
+
+		/* Nothing should be waiting on the timeout */
+		kvm_mips_callbacks->queue_timer_int(vcpu);
+
+		/*
+		 * Restart the timer if it was running based on the expiry time
+		 * we read, so that we don't push it back 2 periods.
+		 */
+		if (running) {
+			expires = ktime_add_ns(expires,
+					       vcpu->arch.count_period);
+			hrtimer_start(&vcpu->arch.comparecount_timer, expires,
+				      HRTIMER_MODE_ABS);
+		}
+	}
+
+	return count;
+}
+
+/**
+ * kvm_mips_read_count() - Read the current count value.
+ * @vcpu:	Virtual CPU.
+ *
+ * Read the current guest CP0_Count value, taking into account whether the timer
+ * is stopped.
+ *
+ * Returns:	The current guest CP0_Count value.
+ */
+u32 kvm_mips_read_count(struct kvm_vcpu *vcpu)
+{
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
+
+	/* If count disabled just read static copy of count */
+	if (kvm_mips_count_disabled(vcpu))
+		return kvm_read_c0_guest_count(cop0);
+
+	return kvm_mips_read_count_running(vcpu, ktime_get());
+}
+
+/**
+ * kvm_mips_freeze_hrtimer() - Safely stop the hrtimer.
+ * @vcpu:	Virtual CPU.
+ * @count:	Output pointer for CP0_Count value at point of freeze.
+ *
+ * Freeze the hrtimer safely and return both the ktime and the CP0_Count value
+ * at the point it was frozen. It is guaranteed that any pending interrupts at
+ * the point it was frozen are handled, and none after that point.
+ *
+ * This is useful where the time/CP0_Count is needed in the calculation of the
+ * new parameters.
+ *
+ * Assumes !kvm_mips_count_disabled(@vcpu) (guest CP0_Count timer is running).
+ *
+ * Returns:	The ktime at the point of freeze.
+ */
+ktime_t kvm_mips_freeze_hrtimer(struct kvm_vcpu *vcpu, u32 *count)
+{
+	ktime_t now;
+
+	/* stop hrtimer before finding time */
+	hrtimer_cancel(&vcpu->arch.comparecount_timer);
+	now = ktime_get();
+
+	/* find count at this point and handle pending hrtimer */
+	*count = kvm_mips_read_count_running(vcpu, now);
+
+	return now;
+}
+
+/**
+ * kvm_mips_resume_hrtimer() - Resume hrtimer, updating expiry.
+ * @vcpu:	Virtual CPU.
+ * @now:	ktime at point of resume.
+ * @count:	CP0_Count at point of resume.
+ *
+ * Resumes the timer and updates the timer expiry based on @now and @count.
+ * This can be used in conjunction with kvm_mips_freeze_timer() when timer
+ * parameters need to be changed.
+ *
+ * It is guaranteed that a timer interrupt immediately after resume will be
+ * handled, but not if CP_Compare is exactly at @count. That case is already
+ * handled by kvm_mips_freeze_timer().
+ *
+ * Assumes !kvm_mips_count_disabled(@vcpu) (guest CP0_Count timer is running).
+ */
+static void kvm_mips_resume_hrtimer(struct kvm_vcpu *vcpu,
+				    ktime_t now, u32 count)
+{
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
+	u32 compare;
+	u64 delta;
+	ktime_t expire;
+
+	/* Calculate timeout (wrap 0 to 2^32) */
+	compare = kvm_read_c0_guest_compare(cop0);
+	delta = (u64)(u32)(compare - count - 1) + 1;
+	delta = div_u64(delta * NSEC_PER_SEC, vcpu->arch.count_hz);
+	expire = ktime_add_ns(now, delta);
+
+	/* Update hrtimer to use new timeout */
+	hrtimer_cancel(&vcpu->arch.comparecount_timer);
+	hrtimer_start(&vcpu->arch.comparecount_timer, expire, HRTIMER_MODE_ABS);
+}
+
+/**
+ * kvm_mips_restore_hrtimer() - Restore hrtimer after a gap, updating expiry.
+ * @vcpu:	Virtual CPU.
+ * @before:	Time before Count was saved, lower bound of drift calculation.
+ * @count:	CP0_Count at point of restore.
+ * @min_drift:	Minimum amount of drift permitted before correction.
+ *		Must be <= 0.
+ *
+ * Restores the timer from a particular @count, accounting for drift. This can
+ * be used in conjunction with kvm_mips_freeze_timer() when a hardware timer is
+ * to be used for a period of time, but the exact ktime corresponding to the
+ * final Count that must be restored is not known.
+ *
+ * It is gauranteed that a timer interrupt immediately after restore will be
+ * handled, but not if CP0_Compare is exactly at @count. That case should
+ * already be handled when the hardware timer state is saved.
+ *
+ * Assumes !kvm_mips_count_disabled(@vcpu) (guest CP0_Count timer is not
+ * stopped).
+ *
+ * Returns:	Amount of correction to count_bias due to drift.
+ */
+int kvm_mips_restore_hrtimer(struct kvm_vcpu *vcpu, ktime_t before,
+			     u32 count, int min_drift)
+{
+	ktime_t now, count_time;
+	u32 now_count, before_count;
+	u64 delta;
+	int drift, ret = 0;
+
+	/* Calculate expected count at before */
+	before_count = vcpu->arch.count_bias +
+			kvm_mips_ktime_to_count(vcpu, before);
+
+	/*
+	 * Detect significantly negative drift, where count is lower than
+	 * expected. Some negative drift is expected when hardware counter is
+	 * set after kvm_mips_freeze_timer(), and it is harmless to allow the
+	 * time to jump forwards a little, within reason. If the drift is too
+	 * significant, adjust the bias to avoid a big Guest.CP0_Count jump.
+	 */
+	drift = count - before_count;
+	if (drift < min_drift) {
+		count_time = before;
+		vcpu->arch.count_bias += drift;
+		ret = drift;
+		goto resume;
+	}
+
+	/* Calculate expected count right now */
+	now = ktime_get();
+	now_count = vcpu->arch.count_bias + kvm_mips_ktime_to_count(vcpu, now);
+
+	/*
+	 * Detect positive drift, where count is higher than expected, and
+	 * adjust the bias to avoid guest time going backwards.
+	 */
+	drift = count - now_count;
+	if (drift > 0) {
+		count_time = now;
+		vcpu->arch.count_bias += drift;
+		ret = drift;
+		goto resume;
+	}
+
+	/* Subtract nanosecond delta to find ktime when count was read */
+	delta = (u64)(u32)(now_count - count);
+	delta = div_u64(delta * NSEC_PER_SEC, vcpu->arch.count_hz);
+	count_time = ktime_sub_ns(now, delta);
+
+resume:
+	/* Resume using the calculated ktime */
+	kvm_mips_resume_hrtimer(vcpu, count_time, count);
+	return ret;
+}
+
+/**
+ * kvm_mips_write_count() - Modify the count and update timer.
+ * @vcpu:	Virtual CPU.
+ * @count:	Guest CP0_Count value to set.
+ *
+ * Sets the CP0_Count value and updates the timer accordingly.
+ */
+void kvm_mips_write_count(struct kvm_vcpu *vcpu, u32 count)
+{
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
+	ktime_t now;
+
+	/* Calculate bias */
+	now = kvm_mips_count_time(vcpu);
+	vcpu->arch.count_bias = count - kvm_mips_ktime_to_count(vcpu, now);
+
+	if (kvm_mips_count_disabled(vcpu))
+		/* The timer's disabled, adjust the static count */
+		kvm_write_c0_guest_count(cop0, count);
+	else
+		/* Update timeout */
+		kvm_mips_resume_hrtimer(vcpu, now, count);
+}
+
+/**
+ * kvm_mips_init_count() - Initialise timer.
+ * @vcpu:	Virtual CPU.
+ * @count_hz:	Frequency of timer.
+ *
+ * Initialise the timer to the specified frequency, zero it, and set it going if
+ * it's enabled.
+ */
+void kvm_mips_init_count(struct kvm_vcpu *vcpu, unsigned long count_hz)
+{
+	vcpu->arch.count_hz = count_hz;
+	vcpu->arch.count_period = div_u64((u64)NSEC_PER_SEC << 32, count_hz);
+	vcpu->arch.count_dyn_bias = 0;
+
+	/* Starting at 0 */
+	kvm_mips_write_count(vcpu, 0);
+}
+
+/**
+ * kvm_mips_set_count_hz() - Update the frequency of the timer.
+ * @vcpu:	Virtual CPU.
+ * @count_hz:	Frequency of CP0_Count timer in Hz.
+ *
+ * Change the frequency of the CP0_Count timer. This is done atomically so that
+ * CP0_Count is continuous and no timer interrupt is lost.
+ *
+ * Returns:	-EINVAL if @count_hz is out of range.
+ *		0 on success.
+ */
+int kvm_mips_set_count_hz(struct kvm_vcpu *vcpu, s64 count_hz)
+{
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
+	int dc;
+	ktime_t now;
+	u32 count;
+
+	/* ensure the frequency is in a sensible range... */
+	if (count_hz <= 0 || count_hz > NSEC_PER_SEC)
+		return -EINVAL;
+	/* ... and has actually changed */
+	if (vcpu->arch.count_hz == count_hz)
+		return 0;
+
+	/* Safely freeze timer so we can keep it continuous */
+	dc = kvm_mips_count_disabled(vcpu);
+	if (dc) {
+		now = kvm_mips_count_time(vcpu);
+		count = kvm_read_c0_guest_count(cop0);
+	} else {
+		now = kvm_mips_freeze_hrtimer(vcpu, &count);
+	}
+
+	/* Update the frequency */
+	vcpu->arch.count_hz = count_hz;
+	vcpu->arch.count_period = div_u64((u64)NSEC_PER_SEC << 32, count_hz);
+	vcpu->arch.count_dyn_bias = 0;
+
+	/* Calculate adjusted bias so dynamic count is unchanged */
+	vcpu->arch.count_bias = count - kvm_mips_ktime_to_count(vcpu, now);
+
+	/* Update and resume hrtimer */
+	if (!dc)
+		kvm_mips_resume_hrtimer(vcpu, now, count);
+	return 0;
+}
+
+/**
+ * kvm_mips_write_compare() - Modify compare and update timer.
+ * @vcpu:	Virtual CPU.
+ * @compare:	New CP0_Compare value.
+ * @ack:	Whether to acknowledge timer interrupt.
+ *
+ * Update CP0_Compare to a new value and update the timeout.
+ * If @ack, atomically acknowledge any pending timer interrupt, otherwise ensure
+ * any pending timer interrupt is preserved.
+ */
+void kvm_mips_write_compare(struct kvm_vcpu *vcpu, u32 compare, bool ack)
+{
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
+	int dc;
+	u32 old_compare = kvm_read_c0_guest_compare(cop0);
+	s32 delta = compare - old_compare;
+	u32 cause;
+	ktime_t now = ktime_set(0, 0); /* silence bogus GCC warning */
+	u32 count;
+
+	/* if unchanged, must just be an ack */
+	if (old_compare == compare) {
+		if (!ack)
+			return;
+		kvm_mips_callbacks->dequeue_timer_int(vcpu);
+		kvm_write_c0_guest_compare(cop0, compare);
+		return;
+	}
+
+	/*
+	 * If guest CP0_Compare moves forward, CP0_GTOffset should be adjusted
+	 * too to prevent guest CP0_Count hitting guest CP0_Compare.
+	 *
+	 * The new GTOffset corresponds to the new value of CP0_Compare, and is
+	 * set prior to it being written into the guest context. We disable
+	 * preemption until the new value is written to prevent restore of a
+	 * GTOffset corresponding to the old CP0_Compare value.
+	 */
+	if (delta > 0) {
+		preempt_disable();
+		write_c0_gtoffset(compare - read_c0_count());
+		back_to_back_c0_hazard();
+	}
+
+	/* freeze_hrtimer() takes care of timer interrupts <= count */
+	dc = kvm_mips_count_disabled(vcpu);
+	if (!dc)
+		now = kvm_mips_freeze_hrtimer(vcpu, &count);
+
+	if (ack)
+		kvm_mips_callbacks->dequeue_timer_int(vcpu);
+	else
+		/*
+		 * With VZ, writing CP0_Compare acks (clears) CP0_Cause.TI, so
+		 * preserve guest CP0_Cause.TI if we don't want to ack it.
+		 */
+		cause = kvm_read_c0_guest_cause(cop0);
+
+	kvm_write_c0_guest_compare(cop0, compare);
+
+	if (delta > 0)
+		preempt_enable();
+
+	back_to_back_c0_hazard();
+
+	if (!ack && cause & CAUSEF_TI)
+		kvm_write_c0_guest_cause(cop0, cause);
+
+	/* resume_hrtimer() takes care of timer interrupts > count */
+	if (!dc)
+		kvm_mips_resume_hrtimer(vcpu, now, count);
+
+	/*
+	 * If guest CP0_Compare is moving backward, we delay CP0_GTOffset change
+	 * until after the new CP0_Compare is written, otherwise new guest
+	 * CP0_Count could hit new guest CP0_Compare.
+	 */
+	if (delta <= 0)
+		write_c0_gtoffset(compare - read_c0_count());
+}
+
+/**
+ * kvm_mips_count_disable() - Disable count.
+ * @vcpu:	Virtual CPU.
+ *
+ * Disable the CP0_Count timer. A timer interrupt on or before the final stop
+ * time will be handled but not after.
+ *
+ * Assumes CP0_Count was previously enabled but now Guest.CP0_Cause.DC or
+ * count_ctl.DC has been set (count disabled).
+ *
+ * Returns:	The time that the timer was stopped.
+ */
+static ktime_t kvm_mips_count_disable(struct kvm_vcpu *vcpu)
+{
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
+	u32 count;
+	ktime_t now;
+
+	/* Stop hrtimer */
+	hrtimer_cancel(&vcpu->arch.comparecount_timer);
+
+	/* Set the static count from the dynamic count, handling pending TI */
+	now = ktime_get();
+	count = kvm_mips_read_count_running(vcpu, now);
+	kvm_write_c0_guest_count(cop0, count);
+
+	return now;
+}
+
+/**
+ * kvm_mips_count_disable_cause() - Disable count using CP0_Cause.DC.
+ * @vcpu:	Virtual CPU.
+ *
+ * Disable the CP0_Count timer and set CP0_Cause.DC. A timer interrupt on or
+ * before the final stop time will be handled if the timer isn't disabled by
+ * count_ctl.DC, but not after.
+ *
+ * Assumes CP0_Cause.DC is clear (count enabled).
+ */
+void kvm_mips_count_disable_cause(struct kvm_vcpu *vcpu)
+{
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
+
+	kvm_set_c0_guest_cause(cop0, CAUSEF_DC);
+	if (!(vcpu->arch.count_ctl & KVM_REG_MIPS_COUNT_CTL_DC))
+		kvm_mips_count_disable(vcpu);
+}
+
+/**
+ * kvm_mips_count_enable_cause() - Enable count using CP0_Cause.DC.
+ * @vcpu:	Virtual CPU.
+ *
+ * Enable the CP0_Count timer and clear CP0_Cause.DC. A timer interrupt after
+ * the start time will be handled if the timer isn't disabled by count_ctl.DC,
+ * potentially before even returning, so the caller should be careful with
+ * ordering of CP0_Cause modifications so as not to lose it.
+ *
+ * Assumes CP0_Cause.DC is set (count disabled).
+ */
+void kvm_mips_count_enable_cause(struct kvm_vcpu *vcpu)
+{
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
+	u32 count;
+
+	kvm_clear_c0_guest_cause(cop0, CAUSEF_DC);
+
+	/*
+	 * Set the dynamic count to match the static count.
+	 * This starts the hrtimer if count_ctl.DC allows it.
+	 * Otherwise it conveniently updates the biases.
+	 */
+	count = kvm_read_c0_guest_count(cop0);
+	kvm_mips_write_count(vcpu, count);
+}
+
+/**
+ * kvm_mips_set_count_ctl() - Update the count control KVM register.
+ * @vcpu:	Virtual CPU.
+ * @count_ctl:	Count control register new value.
+ *
+ * Set the count control KVM register. The timer is updated accordingly.
+ *
+ * Returns:	-EINVAL if reserved bits are set.
+ *		0 on success.
+ */
+int kvm_mips_set_count_ctl(struct kvm_vcpu *vcpu, s64 count_ctl)
+{
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
+	s64 changed = count_ctl ^ vcpu->arch.count_ctl;
+	s64 delta;
+	ktime_t expire, now;
+	u32 count, compare;
+
+	/* Only allow defined bits to be changed */
+	if (changed & ~(s64)(KVM_REG_MIPS_COUNT_CTL_DC))
+		return -EINVAL;
+
+	/* Apply new value */
+	vcpu->arch.count_ctl = count_ctl;
+
+	/* Master CP0_Count disable */
+	if (changed & KVM_REG_MIPS_COUNT_CTL_DC) {
+		/* Is CP0_Cause.DC already disabling CP0_Count? */
+		if (kvm_read_c0_guest_cause(cop0) & CAUSEF_DC) {
+			if (count_ctl & KVM_REG_MIPS_COUNT_CTL_DC)
+				/* Just record the current time */
+				vcpu->arch.count_resume = ktime_get();
+		} else if (count_ctl & KVM_REG_MIPS_COUNT_CTL_DC) {
+			/* disable timer and record current time */
+			vcpu->arch.count_resume = kvm_mips_count_disable(vcpu);
+		} else {
+			/*
+			 * Calculate timeout relative to static count at resume
+			 * time (wrap 0 to 2^32).
+			 */
+			count = kvm_read_c0_guest_count(cop0);
+			compare = kvm_read_c0_guest_compare(cop0);
+			delta = (u64)(u32)(compare - count - 1) + 1;
+			delta = div_u64(delta * NSEC_PER_SEC,
+					vcpu->arch.count_hz);
+			expire = ktime_add_ns(vcpu->arch.count_resume, delta);
+
+			/* Handle pending interrupt */
+			now = ktime_get();
+			if (ktime_compare(now, expire) >= 0)
+				/* Nothing should be waiting on the timeout */
+				kvm_mips_callbacks->queue_timer_int(vcpu);
+
+			/* Resume hrtimer without changing bias */
+			count = kvm_mips_read_count_running(vcpu, now);
+			kvm_mips_resume_hrtimer(vcpu, now, count);
+		}
+	}
+
+	return 0;
+}
+
+/**
+ * kvm_mips_set_count_resume() - Update the count resume KVM register.
+ * @vcpu:		Virtual CPU.
+ * @count_resume:	Count resume register new value.
+ *
+ * Set the count resume KVM register.
+ *
+ * Returns:	-EINVAL if out of valid range (0..now).
+ *		0 on success.
+ */
+int kvm_mips_set_count_resume(struct kvm_vcpu *vcpu, s64 count_resume)
+{
+	/*
+	 * It doesn't make sense for the resume time to be in the future, as it
+	 * would be possible for the next interrupt to be more than a full
+	 * period in the future.
+	 */
+	if (count_resume < 0 || count_resume > ktime_to_ns(ktime_get()))
+		return -EINVAL;
+
+	vcpu->arch.count_resume = ns_to_ktime(count_resume);
+	return 0;
+}
+
+/**
+ * kvm_mips_count_timeout() - Push timer forward on timeout.
+ * @vcpu:	Virtual CPU.
+ *
+ * Handle an hrtimer event by push the hrtimer forward a period.
+ *
+ * Returns:	The hrtimer_restart value to return to the hrtimer subsystem.
+ */
+enum hrtimer_restart kvm_mips_count_timeout(struct kvm_vcpu *vcpu)
+{
+	/* Add the Count period to the current expiry time */
+	hrtimer_add_expires_ns(&vcpu->arch.comparecount_timer,
+			       vcpu->arch.count_period);
+	return HRTIMER_RESTART;
+}
+
+enum emulation_result kvm_mips_emul_wait(struct kvm_vcpu *vcpu)
+{
+	kvm_debug("[%#lx] !!!WAIT!!! (%#lx)\n", vcpu->arch.pc,
+		  vcpu->arch.pending_exceptions);
+
+	++vcpu->stat.wait_exits;
+	trace_kvm_exit(vcpu, KVM_TRACE_EXIT_WAIT);
+	if (!vcpu->arch.pending_exceptions) {
+		kvm_vz_lose_htimer(vcpu);
+		vcpu->arch.wait = 1;
+		kvm_vcpu_halt(vcpu);
+
+		/*
+		 * We are runnable, then definitely go off to user space to
+		 * check if any I/O interrupts are pending.
+		 */
+		if (kvm_arch_vcpu_runnable(vcpu))
+			vcpu->run->exit_reason = KVM_EXIT_IRQ_WINDOW_OPEN;
+	}
+
+	return EMULATE_DONE;
+}
+
+enum emulation_result kvm_mips_emulate_store(union mips_instruction inst,
+					     u32 cause,
+					     struct kvm_vcpu *vcpu)
+{
+	int r;
+	enum emulation_result er;
+	u32 rt;
+	struct kvm_run *run = vcpu->run;
+	void *data = run->mmio.data;
+	unsigned int imme;
+	unsigned long curr_pc;
+
+	/*
+	 * Update PC and hold onto current PC in case there is
+	 * an error and we want to rollback the PC
+	 */
+	curr_pc = vcpu->arch.pc;
+	er = update_pc(vcpu, cause);
+	if (er == EMULATE_FAIL)
+		return er;
+
+	rt = inst.i_format.rt;
+
+	run->mmio.phys_addr = kvm_mips_callbacks->gva_to_gpa(
+						vcpu->arch.host_cp0_badvaddr);
+	if (run->mmio.phys_addr == KVM_INVALID_ADDR)
+		goto out_fail;
+
+	switch (inst.i_format.opcode) {
+#if defined(CONFIG_64BIT)
+	case sd_op:
+		run->mmio.len = 8;
+		*(u64 *)data = vcpu->arch.gprs[rt];
+
+		kvm_debug("[%#lx] OP_SD: eaddr: %#lx, gpr: %#lx, data: %#llx\n",
+			  vcpu->arch.pc, vcpu->arch.host_cp0_badvaddr,
+			  vcpu->arch.gprs[rt], *(u64 *)data);
+		break;
+#endif
+
+	case sw_op:
+		run->mmio.len = 4;
+		*(u32 *)data = vcpu->arch.gprs[rt];
+
+		kvm_debug("[%#lx] OP_SW: eaddr: %#lx, gpr: %#lx, data: %#x\n",
+			  vcpu->arch.pc, vcpu->arch.host_cp0_badvaddr,
+			  vcpu->arch.gprs[rt], *(u32 *)data);
+		break;
+
+	case sh_op:
+		run->mmio.len = 2;
+		*(u16 *)data = vcpu->arch.gprs[rt];
+
+		kvm_debug("[%#lx] OP_SH: eaddr: %#lx, gpr: %#lx, data: %#x\n",
+			  vcpu->arch.pc, vcpu->arch.host_cp0_badvaddr,
+			  vcpu->arch.gprs[rt], *(u16 *)data);
+		break;
+
+	case sb_op:
+		run->mmio.len = 1;
+		*(u8 *)data = vcpu->arch.gprs[rt];
+
+		kvm_debug("[%#lx] OP_SB: eaddr: %#lx, gpr: %#lx, data: %#x\n",
+			  vcpu->arch.pc, vcpu->arch.host_cp0_badvaddr,
+			  vcpu->arch.gprs[rt], *(u8 *)data);
+		break;
+
+	case swl_op:
+		run->mmio.phys_addr = kvm_mips_callbacks->gva_to_gpa(
+					vcpu->arch.host_cp0_badvaddr) & (~0x3);
+		run->mmio.len = 4;
+		imme = vcpu->arch.host_cp0_badvaddr & 0x3;
+		switch (imme) {
+		case 0:
+			*(u32 *)data = ((*(u32 *)data) & 0xffffff00) |
+					(vcpu->arch.gprs[rt] >> 24);
+			break;
+		case 1:
+			*(u32 *)data = ((*(u32 *)data) & 0xffff0000) |
+					(vcpu->arch.gprs[rt] >> 16);
+			break;
+		case 2:
+			*(u32 *)data = ((*(u32 *)data) & 0xff000000) |
+					(vcpu->arch.gprs[rt] >> 8);
+			break;
+		case 3:
+			*(u32 *)data = vcpu->arch.gprs[rt];
+			break;
+		default:
+			break;
+		}
+
+		kvm_debug("[%#lx] OP_SWL: eaddr: %#lx, gpr: %#lx, data: %#x\n",
+			  vcpu->arch.pc, vcpu->arch.host_cp0_badvaddr,
+			  vcpu->arch.gprs[rt], *(u32 *)data);
+		break;
+
+	case swr_op:
+		run->mmio.phys_addr = kvm_mips_callbacks->gva_to_gpa(
+					vcpu->arch.host_cp0_badvaddr) & (~0x3);
+		run->mmio.len = 4;
+		imme = vcpu->arch.host_cp0_badvaddr & 0x3;
+		switch (imme) {
+		case 0:
+			*(u32 *)data = vcpu->arch.gprs[rt];
+			break;
+		case 1:
+			*(u32 *)data = ((*(u32 *)data) & 0xff) |
+					(vcpu->arch.gprs[rt] << 8);
+			break;
+		case 2:
+			*(u32 *)data = ((*(u32 *)data) & 0xffff) |
+					(vcpu->arch.gprs[rt] << 16);
+			break;
+		case 3:
+			*(u32 *)data = ((*(u32 *)data) & 0xffffff) |
+					(vcpu->arch.gprs[rt] << 24);
+			break;
+		default:
+			break;
+		}
+
+		kvm_debug("[%#lx] OP_SWR: eaddr: %#lx, gpr: %#lx, data: %#x\n",
+			  vcpu->arch.pc, vcpu->arch.host_cp0_badvaddr,
+			  vcpu->arch.gprs[rt], *(u32 *)data);
+		break;
+
+#if defined(CONFIG_64BIT)
+	case sdl_op:
+		run->mmio.phys_addr = kvm_mips_callbacks->gva_to_gpa(
+					vcpu->arch.host_cp0_badvaddr) & (~0x7);
+
+		run->mmio.len = 8;
+		imme = vcpu->arch.host_cp0_badvaddr & 0x7;
+		switch (imme) {
+		case 0:
+			*(u64 *)data = ((*(u64 *)data) & 0xffffffffffffff00) |
+					((vcpu->arch.gprs[rt] >> 56) & 0xff);
+			break;
+		case 1:
+			*(u64 *)data = ((*(u64 *)data) & 0xffffffffffff0000) |
+					((vcpu->arch.gprs[rt] >> 48) & 0xffff);
+			break;
+		case 2:
+			*(u64 *)data = ((*(u64 *)data) & 0xffffffffff000000) |
+					((vcpu->arch.gprs[rt] >> 40) & 0xffffff);
+			break;
+		case 3:
+			*(u64 *)data = ((*(u64 *)data) & 0xffffffff00000000) |
+					((vcpu->arch.gprs[rt] >> 32) & 0xffffffff);
+			break;
+		case 4:
+			*(u64 *)data = ((*(u64 *)data) & 0xffffff0000000000) |
+					((vcpu->arch.gprs[rt] >> 24) & 0xffffffffff);
+			break;
+		case 5:
+			*(u64 *)data = ((*(u64 *)data) & 0xffff000000000000) |
+					((vcpu->arch.gprs[rt] >> 16) & 0xffffffffffff);
+			break;
+		case 6:
+			*(u64 *)data = ((*(u64 *)data) & 0xff00000000000000) |
+					((vcpu->arch.gprs[rt] >> 8) & 0xffffffffffffff);
+			break;
+		case 7:
+			*(u64 *)data = vcpu->arch.gprs[rt];
+			break;
+		default:
+			break;
+		}
+
+		kvm_debug("[%#lx] OP_SDL: eaddr: %#lx, gpr: %#lx, data: %llx\n",
+			  vcpu->arch.pc, vcpu->arch.host_cp0_badvaddr,
+			  vcpu->arch.gprs[rt], *(u64 *)data);
+		break;
+
+	case sdr_op:
+		run->mmio.phys_addr = kvm_mips_callbacks->gva_to_gpa(
+					vcpu->arch.host_cp0_badvaddr) & (~0x7);
+
+		run->mmio.len = 8;
+		imme = vcpu->arch.host_cp0_badvaddr & 0x7;
+		switch (imme) {
+		case 0:
+			*(u64 *)data = vcpu->arch.gprs[rt];
+			break;
+		case 1:
+			*(u64 *)data = ((*(u64 *)data) & 0xff) |
+					(vcpu->arch.gprs[rt] << 8);
+			break;
+		case 2:
+			*(u64 *)data = ((*(u64 *)data) & 0xffff) |
+					(vcpu->arch.gprs[rt] << 16);
+			break;
+		case 3:
+			*(u64 *)data = ((*(u64 *)data) & 0xffffff) |
+					(vcpu->arch.gprs[rt] << 24);
+			break;
+		case 4:
+			*(u64 *)data = ((*(u64 *)data) & 0xffffffff) |
+					(vcpu->arch.gprs[rt] << 32);
+			break;
+		case 5:
+			*(u64 *)data = ((*(u64 *)data) & 0xffffffffff) |
+					(vcpu->arch.gprs[rt] << 40);
+			break;
+		case 6:
+			*(u64 *)data = ((*(u64 *)data) & 0xffffffffffff) |
+					(vcpu->arch.gprs[rt] << 48);
+			break;
+		case 7:
+			*(u64 *)data = ((*(u64 *)data) & 0xffffffffffffff) |
+					(vcpu->arch.gprs[rt] << 56);
+			break;
+		default:
+			break;
+		}
+
+		kvm_debug("[%#lx] OP_SDR: eaddr: %#lx, gpr: %#lx, data: %llx\n",
+			  vcpu->arch.pc, vcpu->arch.host_cp0_badvaddr,
+			  vcpu->arch.gprs[rt], *(u64 *)data);
+		break;
+#endif
+
+#ifdef CONFIG_CPU_LOONGSON64
+	case sdc2_op:
+		rt = inst.loongson3_lsdc2_format.rt;
+		switch (inst.loongson3_lsdc2_format.opcode1) {
+		/*
+		 * Loongson-3 overridden sdc2 instructions.
+		 * opcode1              instruction
+		 *   0x0          gssbx: store 1 bytes from GPR
+		 *   0x1          gsshx: store 2 bytes from GPR
+		 *   0x2          gsswx: store 4 bytes from GPR
+		 *   0x3          gssdx: store 8 bytes from GPR
+		 */
+		case 0x0:
+			run->mmio.len = 1;
+			*(u8 *)data = vcpu->arch.gprs[rt];
+
+			kvm_debug("[%#lx] OP_GSSBX: eaddr: %#lx, gpr: %#lx, data: %#x\n",
+				  vcpu->arch.pc, vcpu->arch.host_cp0_badvaddr,
+				  vcpu->arch.gprs[rt], *(u8 *)data);
+			break;
+		case 0x1:
+			run->mmio.len = 2;
+			*(u16 *)data = vcpu->arch.gprs[rt];
+
+			kvm_debug("[%#lx] OP_GSSSHX: eaddr: %#lx, gpr: %#lx, data: %#x\n",
+				  vcpu->arch.pc, vcpu->arch.host_cp0_badvaddr,
+				  vcpu->arch.gprs[rt], *(u16 *)data);
+			break;
+		case 0x2:
+			run->mmio.len = 4;
+			*(u32 *)data = vcpu->arch.gprs[rt];
+
+			kvm_debug("[%#lx] OP_GSSWX: eaddr: %#lx, gpr: %#lx, data: %#x\n",
+				  vcpu->arch.pc, vcpu->arch.host_cp0_badvaddr,
+				  vcpu->arch.gprs[rt], *(u32 *)data);
+			break;
+		case 0x3:
+			run->mmio.len = 8;
+			*(u64 *)data = vcpu->arch.gprs[rt];
+
+			kvm_debug("[%#lx] OP_GSSDX: eaddr: %#lx, gpr: %#lx, data: %#llx\n",
+				  vcpu->arch.pc, vcpu->arch.host_cp0_badvaddr,
+				  vcpu->arch.gprs[rt], *(u64 *)data);
+			break;
+		default:
+			kvm_err("Godson Extended GS-Store not yet supported (inst=0x%08x)\n",
+				inst.word);
+			break;
+		}
+		break;
+#endif
+	default:
+		kvm_err("Store not yet supported (inst=0x%08x)\n",
+			inst.word);
+		goto out_fail;
+	}
+
+	vcpu->mmio_needed = 1;
+	run->mmio.is_write = 1;
+	vcpu->mmio_is_write = 1;
+
+	r = kvm_io_bus_write(vcpu, KVM_MMIO_BUS,
+			run->mmio.phys_addr, run->mmio.len, data);
+
+	if (!r) {
+		vcpu->mmio_needed = 0;
+		return EMULATE_DONE;
+	}
+
+	return EMULATE_DO_MMIO;
+
+out_fail:
+	/* Rollback PC if emulation was unsuccessful */
+	vcpu->arch.pc = curr_pc;
+	return EMULATE_FAIL;
+}
+
+enum emulation_result kvm_mips_emulate_load(union mips_instruction inst,
+					    u32 cause, struct kvm_vcpu *vcpu)
+{
+	struct kvm_run *run = vcpu->run;
+	int r;
+	enum emulation_result er;
+	unsigned long curr_pc;
+	u32 op, rt;
+	unsigned int imme;
+
+	rt = inst.i_format.rt;
+	op = inst.i_format.opcode;
+
+	/*
+	 * Find the resume PC now while we have safe and easy access to the
+	 * prior branch instruction, and save it for
+	 * kvm_mips_complete_mmio_load() to restore later.
+	 */
+	curr_pc = vcpu->arch.pc;
+	er = update_pc(vcpu, cause);
+	if (er == EMULATE_FAIL)
+		return er;
+	vcpu->arch.io_pc = vcpu->arch.pc;
+	vcpu->arch.pc = curr_pc;
+
+	vcpu->arch.io_gpr = rt;
+
+	run->mmio.phys_addr = kvm_mips_callbacks->gva_to_gpa(
+						vcpu->arch.host_cp0_badvaddr);
+	if (run->mmio.phys_addr == KVM_INVALID_ADDR)
+		return EMULATE_FAIL;
+
+	vcpu->mmio_needed = 2;	/* signed */
+	switch (op) {
+#if defined(CONFIG_64BIT)
+	case ld_op:
+		run->mmio.len = 8;
+		break;
+
+	case lwu_op:
+		vcpu->mmio_needed = 1;	/* unsigned */
+		fallthrough;
+#endif
+	case lw_op:
+		run->mmio.len = 4;
+		break;
+
+	case lhu_op:
+		vcpu->mmio_needed = 1;	/* unsigned */
+		fallthrough;
+	case lh_op:
+		run->mmio.len = 2;
+		break;
+
+	case lbu_op:
+		vcpu->mmio_needed = 1;	/* unsigned */
+		fallthrough;
+	case lb_op:
+		run->mmio.len = 1;
+		break;
+
+	case lwl_op:
+		run->mmio.phys_addr = kvm_mips_callbacks->gva_to_gpa(
+					vcpu->arch.host_cp0_badvaddr) & (~0x3);
+
+		run->mmio.len = 4;
+		imme = vcpu->arch.host_cp0_badvaddr & 0x3;
+		switch (imme) {
+		case 0:
+			vcpu->mmio_needed = 3;	/* 1 byte */
+			break;
+		case 1:
+			vcpu->mmio_needed = 4;	/* 2 bytes */
+			break;
+		case 2:
+			vcpu->mmio_needed = 5;	/* 3 bytes */
+			break;
+		case 3:
+			vcpu->mmio_needed = 6;	/* 4 bytes */
+			break;
+		default:
+			break;
+		}
+		break;
+
+	case lwr_op:
+		run->mmio.phys_addr = kvm_mips_callbacks->gva_to_gpa(
+					vcpu->arch.host_cp0_badvaddr) & (~0x3);
+
+		run->mmio.len = 4;
+		imme = vcpu->arch.host_cp0_badvaddr & 0x3;
+		switch (imme) {
+		case 0:
+			vcpu->mmio_needed = 7;	/* 4 bytes */
+			break;
+		case 1:
+			vcpu->mmio_needed = 8;	/* 3 bytes */
+			break;
+		case 2:
+			vcpu->mmio_needed = 9;	/* 2 bytes */
+			break;
+		case 3:
+			vcpu->mmio_needed = 10;	/* 1 byte */
+			break;
+		default:
+			break;
+		}
+		break;
+
+#if defined(CONFIG_64BIT)
+	case ldl_op:
+		run->mmio.phys_addr = kvm_mips_callbacks->gva_to_gpa(
+					vcpu->arch.host_cp0_badvaddr) & (~0x7);
+
+		run->mmio.len = 8;
+		imme = vcpu->arch.host_cp0_badvaddr & 0x7;
+		switch (imme) {
+		case 0:
+			vcpu->mmio_needed = 11;	/* 1 byte */
+			break;
+		case 1:
+			vcpu->mmio_needed = 12;	/* 2 bytes */
+			break;
+		case 2:
+			vcpu->mmio_needed = 13;	/* 3 bytes */
+			break;
+		case 3:
+			vcpu->mmio_needed = 14;	/* 4 bytes */
+			break;
+		case 4:
+			vcpu->mmio_needed = 15;	/* 5 bytes */
+			break;
+		case 5:
+			vcpu->mmio_needed = 16;	/* 6 bytes */
+			break;
+		case 6:
+			vcpu->mmio_needed = 17;	/* 7 bytes */
+			break;
+		case 7:
+			vcpu->mmio_needed = 18;	/* 8 bytes */
+			break;
+		default:
+			break;
+		}
+		break;
+
+	case ldr_op:
+		run->mmio.phys_addr = kvm_mips_callbacks->gva_to_gpa(
+					vcpu->arch.host_cp0_badvaddr) & (~0x7);
+
+		run->mmio.len = 8;
+		imme = vcpu->arch.host_cp0_badvaddr & 0x7;
+		switch (imme) {
+		case 0:
+			vcpu->mmio_needed = 19;	/* 8 bytes */
+			break;
+		case 1:
+			vcpu->mmio_needed = 20;	/* 7 bytes */
+			break;
+		case 2:
+			vcpu->mmio_needed = 21;	/* 6 bytes */
+			break;
+		case 3:
+			vcpu->mmio_needed = 22;	/* 5 bytes */
+			break;
+		case 4:
+			vcpu->mmio_needed = 23;	/* 4 bytes */
+			break;
+		case 5:
+			vcpu->mmio_needed = 24;	/* 3 bytes */
+			break;
+		case 6:
+			vcpu->mmio_needed = 25;	/* 2 bytes */
+			break;
+		case 7:
+			vcpu->mmio_needed = 26;	/* 1 byte */
+			break;
+		default:
+			break;
+		}
+		break;
+#endif
+
+#ifdef CONFIG_CPU_LOONGSON64
+	case ldc2_op:
+		rt = inst.loongson3_lsdc2_format.rt;
+		switch (inst.loongson3_lsdc2_format.opcode1) {
+		/*
+		 * Loongson-3 overridden ldc2 instructions.
+		 * opcode1              instruction
+		 *   0x0          gslbx: store 1 bytes from GPR
+		 *   0x1          gslhx: store 2 bytes from GPR
+		 *   0x2          gslwx: store 4 bytes from GPR
+		 *   0x3          gsldx: store 8 bytes from GPR
+		 */
+		case 0x0:
+			run->mmio.len = 1;
+			vcpu->mmio_needed = 27;	/* signed */
+			break;
+		case 0x1:
+			run->mmio.len = 2;
+			vcpu->mmio_needed = 28;	/* signed */
+			break;
+		case 0x2:
+			run->mmio.len = 4;
+			vcpu->mmio_needed = 29;	/* signed */
+			break;
+		case 0x3:
+			run->mmio.len = 8;
+			vcpu->mmio_needed = 30;	/* signed */
+			break;
+		default:
+			kvm_err("Godson Extended GS-Load for float not yet supported (inst=0x%08x)\n",
+				inst.word);
+			break;
+		}
+		break;
+#endif
+
+	default:
+		kvm_err("Load not yet supported (inst=0x%08x)\n",
+			inst.word);
+		vcpu->mmio_needed = 0;
+		return EMULATE_FAIL;
+	}
+
+	run->mmio.is_write = 0;
+	vcpu->mmio_is_write = 0;
+
+	r = kvm_io_bus_read(vcpu, KVM_MMIO_BUS,
+			run->mmio.phys_addr, run->mmio.len, run->mmio.data);
+
+	if (!r) {
+		kvm_mips_complete_mmio_load(vcpu);
+		vcpu->mmio_needed = 0;
+		return EMULATE_DONE;
+	}
+
+	return EMULATE_DO_MMIO;
+}
+
+enum emulation_result kvm_mips_complete_mmio_load(struct kvm_vcpu *vcpu)
+{
+	struct kvm_run *run = vcpu->run;
+	unsigned long *gpr = &vcpu->arch.gprs[vcpu->arch.io_gpr];
+	enum emulation_result er = EMULATE_DONE;
+
+	if (run->mmio.len > sizeof(*gpr)) {
+		kvm_err("Bad MMIO length: %d", run->mmio.len);
+		er = EMULATE_FAIL;
+		goto done;
+	}
+
+	/* Restore saved resume PC */
+	vcpu->arch.pc = vcpu->arch.io_pc;
+
+	switch (run->mmio.len) {
+	case 8:
+		switch (vcpu->mmio_needed) {
+		case 11:
+			*gpr = (vcpu->arch.gprs[vcpu->arch.io_gpr] & 0xffffffffffffff) |
+				(((*(s64 *)run->mmio.data) & 0xff) << 56);
+			break;
+		case 12:
+			*gpr = (vcpu->arch.gprs[vcpu->arch.io_gpr] & 0xffffffffffff) |
+				(((*(s64 *)run->mmio.data) & 0xffff) << 48);
+			break;
+		case 13:
+			*gpr = (vcpu->arch.gprs[vcpu->arch.io_gpr] & 0xffffffffff) |
+				(((*(s64 *)run->mmio.data) & 0xffffff) << 40);
+			break;
+		case 14:
+			*gpr = (vcpu->arch.gprs[vcpu->arch.io_gpr] & 0xffffffff) |
+				(((*(s64 *)run->mmio.data) & 0xffffffff) << 32);
+			break;
+		case 15:
+			*gpr = (vcpu->arch.gprs[vcpu->arch.io_gpr] & 0xffffff) |
+				(((*(s64 *)run->mmio.data) & 0xffffffffff) << 24);
+			break;
+		case 16:
+			*gpr = (vcpu->arch.gprs[vcpu->arch.io_gpr] & 0xffff) |
+				(((*(s64 *)run->mmio.data) & 0xffffffffffff) << 16);
+			break;
+		case 17:
+			*gpr = (vcpu->arch.gprs[vcpu->arch.io_gpr] & 0xff) |
+				(((*(s64 *)run->mmio.data) & 0xffffffffffffff) << 8);
+			break;
+		case 18:
+		case 19:
+			*gpr = *(s64 *)run->mmio.data;
+			break;
+		case 20:
+			*gpr = (vcpu->arch.gprs[vcpu->arch.io_gpr] & 0xff00000000000000) |
+				((((*(s64 *)run->mmio.data)) >> 8) & 0xffffffffffffff);
+			break;
+		case 21:
+			*gpr = (vcpu->arch.gprs[vcpu->arch.io_gpr] & 0xffff000000000000) |
+				((((*(s64 *)run->mmio.data)) >> 16) & 0xffffffffffff);
+			break;
+		case 22:
+			*gpr = (vcpu->arch.gprs[vcpu->arch.io_gpr] & 0xffffff0000000000) |
+				((((*(s64 *)run->mmio.data)) >> 24) & 0xffffffffff);
+			break;
+		case 23:
+			*gpr = (vcpu->arch.gprs[vcpu->arch.io_gpr] & 0xffffffff00000000) |
+				((((*(s64 *)run->mmio.data)) >> 32) & 0xffffffff);
+			break;
+		case 24:
+			*gpr = (vcpu->arch.gprs[vcpu->arch.io_gpr] & 0xffffffffff000000) |
+				((((*(s64 *)run->mmio.data)) >> 40) & 0xffffff);
+			break;
+		case 25:
+			*gpr = (vcpu->arch.gprs[vcpu->arch.io_gpr] & 0xffffffffffff0000) |
+				((((*(s64 *)run->mmio.data)) >> 48) & 0xffff);
+			break;
+		case 26:
+			*gpr = (vcpu->arch.gprs[vcpu->arch.io_gpr] & 0xffffffffffffff00) |
+				((((*(s64 *)run->mmio.data)) >> 56) & 0xff);
+			break;
+		default:
+			*gpr = *(s64 *)run->mmio.data;
+		}
+		break;
+
+	case 4:
+		switch (vcpu->mmio_needed) {
+		case 1:
+			*gpr = *(u32 *)run->mmio.data;
+			break;
+		case 2:
+			*gpr = *(s32 *)run->mmio.data;
+			break;
+		case 3:
+			*gpr = (vcpu->arch.gprs[vcpu->arch.io_gpr] & 0xffffff) |
+				(((*(s32 *)run->mmio.data) & 0xff) << 24);
+			break;
+		case 4:
+			*gpr = (vcpu->arch.gprs[vcpu->arch.io_gpr] & 0xffff) |
+				(((*(s32 *)run->mmio.data) & 0xffff) << 16);
+			break;
+		case 5:
+			*gpr = (vcpu->arch.gprs[vcpu->arch.io_gpr] & 0xff) |
+				(((*(s32 *)run->mmio.data) & 0xffffff) << 8);
+			break;
+		case 6:
+		case 7:
+			*gpr = *(s32 *)run->mmio.data;
+			break;
+		case 8:
+			*gpr = (vcpu->arch.gprs[vcpu->arch.io_gpr] & 0xff000000) |
+				((((*(s32 *)run->mmio.data)) >> 8) & 0xffffff);
+			break;
+		case 9:
+			*gpr = (vcpu->arch.gprs[vcpu->arch.io_gpr] & 0xffff0000) |
+				((((*(s32 *)run->mmio.data)) >> 16) & 0xffff);
+			break;
+		case 10:
+			*gpr = (vcpu->arch.gprs[vcpu->arch.io_gpr] & 0xffffff00) |
+				((((*(s32 *)run->mmio.data)) >> 24) & 0xff);
+			break;
+		default:
+			*gpr = *(s32 *)run->mmio.data;
+		}
+		break;
+
+	case 2:
+		if (vcpu->mmio_needed == 1)
+			*gpr = *(u16 *)run->mmio.data;
+		else
+			*gpr = *(s16 *)run->mmio.data;
+
+		break;
+	case 1:
+		if (vcpu->mmio_needed == 1)
+			*gpr = *(u8 *)run->mmio.data;
+		else
+			*gpr = *(s8 *)run->mmio.data;
+		break;
+	}
+
+done:
+	return er;
+}
diff --git a/arch/mips/kvm/entry.c b/arch/mips/kvm/entry.c
new file mode 100644
index 000000000..aceed14aa
--- /dev/null
+++ b/arch/mips/kvm/entry.c
@@ -0,0 +1,916 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Generation of main entry point for the guest, exception handling.
+ *
+ * Copyright (C) 2012  MIPS Technologies, Inc.
+ * Authors: Sanjay Lal <sanjayl@kymasys.com>
+ *
+ * Copyright (C) 2016 Imagination Technologies Ltd.
+ */
+
+#include <linux/kvm_host.h>
+#include <linux/log2.h>
+#include <asm/mmu_context.h>
+#include <asm/msa.h>
+#include <asm/setup.h>
+#include <asm/tlbex.h>
+#include <asm/uasm.h>
+
+/* Register names */
+#define ZERO		0
+#define AT		1
+#define V0		2
+#define V1		3
+#define A0		4
+#define A1		5
+
+#if _MIPS_SIM == _MIPS_SIM_ABI32
+#define T0		8
+#define T1		9
+#define T2		10
+#define T3		11
+#endif /* _MIPS_SIM == _MIPS_SIM_ABI32 */
+
+#if _MIPS_SIM == _MIPS_SIM_ABI64 || _MIPS_SIM == _MIPS_SIM_NABI32
+#define T0		12
+#define T1		13
+#define T2		14
+#define T3		15
+#endif /* _MIPS_SIM == _MIPS_SIM_ABI64 || _MIPS_SIM == _MIPS_SIM_NABI32 */
+
+#define S0		16
+#define S1		17
+#define T9		25
+#define K0		26
+#define K1		27
+#define GP		28
+#define SP		29
+#define RA		31
+
+/* Some CP0 registers */
+#define C0_PWBASE	5, 5
+#define C0_HWRENA	7, 0
+#define C0_BADVADDR	8, 0
+#define C0_BADINSTR	8, 1
+#define C0_BADINSTRP	8, 2
+#define C0_PGD		9, 7
+#define C0_ENTRYHI	10, 0
+#define C0_GUESTCTL1	10, 4
+#define C0_STATUS	12, 0
+#define C0_GUESTCTL0	12, 6
+#define C0_CAUSE	13, 0
+#define C0_EPC		14, 0
+#define C0_EBASE	15, 1
+#define C0_CONFIG5	16, 5
+#define C0_DDATA_LO	28, 3
+#define C0_ERROREPC	30, 0
+
+#define CALLFRAME_SIZ   32
+
+#ifdef CONFIG_64BIT
+#define ST0_KX_IF_64	ST0_KX
+#else
+#define ST0_KX_IF_64	0
+#endif
+
+static unsigned int scratch_vcpu[2] = { C0_DDATA_LO };
+static unsigned int scratch_tmp[2] = { C0_ERROREPC };
+
+enum label_id {
+	label_fpu_1 = 1,
+	label_msa_1,
+	label_return_to_host,
+	label_kernel_asid,
+	label_exit_common,
+};
+
+UASM_L_LA(_fpu_1)
+UASM_L_LA(_msa_1)
+UASM_L_LA(_return_to_host)
+UASM_L_LA(_kernel_asid)
+UASM_L_LA(_exit_common)
+
+static void *kvm_mips_build_enter_guest(void *addr);
+static void *kvm_mips_build_ret_from_exit(void *addr);
+static void *kvm_mips_build_ret_to_guest(void *addr);
+static void *kvm_mips_build_ret_to_host(void *addr);
+
+/*
+ * The version of this function in tlbex.c uses current_cpu_type(), but for KVM
+ * we assume symmetry.
+ */
+static int c0_kscratch(void)
+{
+	return 31;
+}
+
+/**
+ * kvm_mips_entry_setup() - Perform global setup for entry code.
+ *
+ * Perform global setup for entry code, such as choosing a scratch register.
+ *
+ * Returns:	0 on success.
+ *		-errno on failure.
+ */
+int kvm_mips_entry_setup(void)
+{
+	/*
+	 * We prefer to use KScratchN registers if they are available over the
+	 * defaults above, which may not work on all cores.
+	 */
+	unsigned int kscratch_mask = cpu_data[0].kscratch_mask;
+
+	if (pgd_reg != -1)
+		kscratch_mask &= ~BIT(pgd_reg);
+
+	/* Pick a scratch register for storing VCPU */
+	if (kscratch_mask) {
+		scratch_vcpu[0] = c0_kscratch();
+		scratch_vcpu[1] = ffs(kscratch_mask) - 1;
+		kscratch_mask &= ~BIT(scratch_vcpu[1]);
+	}
+
+	/* Pick a scratch register to use as a temp for saving state */
+	if (kscratch_mask) {
+		scratch_tmp[0] = c0_kscratch();
+		scratch_tmp[1] = ffs(kscratch_mask) - 1;
+		kscratch_mask &= ~BIT(scratch_tmp[1]);
+	}
+
+	return 0;
+}
+
+static void kvm_mips_build_save_scratch(u32 **p, unsigned int tmp,
+					unsigned int frame)
+{
+	/* Save the VCPU scratch register value in cp0_epc of the stack frame */
+	UASM_i_MFC0(p, tmp, scratch_vcpu[0], scratch_vcpu[1]);
+	UASM_i_SW(p, tmp, offsetof(struct pt_regs, cp0_epc), frame);
+
+	/* Save the temp scratch register value in cp0_cause of stack frame */
+	if (scratch_tmp[0] == c0_kscratch()) {
+		UASM_i_MFC0(p, tmp, scratch_tmp[0], scratch_tmp[1]);
+		UASM_i_SW(p, tmp, offsetof(struct pt_regs, cp0_cause), frame);
+	}
+}
+
+static void kvm_mips_build_restore_scratch(u32 **p, unsigned int tmp,
+					   unsigned int frame)
+{
+	/*
+	 * Restore host scratch register values saved by
+	 * kvm_mips_build_save_scratch().
+	 */
+	UASM_i_LW(p, tmp, offsetof(struct pt_regs, cp0_epc), frame);
+	UASM_i_MTC0(p, tmp, scratch_vcpu[0], scratch_vcpu[1]);
+
+	if (scratch_tmp[0] == c0_kscratch()) {
+		UASM_i_LW(p, tmp, offsetof(struct pt_regs, cp0_cause), frame);
+		UASM_i_MTC0(p, tmp, scratch_tmp[0], scratch_tmp[1]);
+	}
+}
+
+/**
+ * build_set_exc_base() - Assemble code to write exception base address.
+ * @p:		Code buffer pointer.
+ * @reg:	Source register (generated code may set WG bit in @reg).
+ *
+ * Assemble code to modify the exception base address in the EBase register,
+ * using the appropriately sized access and setting the WG bit if necessary.
+ */
+static inline void build_set_exc_base(u32 **p, unsigned int reg)
+{
+	if (cpu_has_ebase_wg) {
+		/* Set WG so that all the bits get written */
+		uasm_i_ori(p, reg, reg, MIPS_EBASE_WG);
+		UASM_i_MTC0(p, reg, C0_EBASE);
+	} else {
+		uasm_i_mtc0(p, reg, C0_EBASE);
+	}
+}
+
+/**
+ * kvm_mips_build_vcpu_run() - Assemble function to start running a guest VCPU.
+ * @addr:	Address to start writing code.
+ *
+ * Assemble the start of the vcpu_run function to run a guest VCPU. The function
+ * conforms to the following prototype:
+ *
+ * int vcpu_run(struct kvm_vcpu *vcpu);
+ *
+ * The exit from the guest and return to the caller is handled by the code
+ * generated by kvm_mips_build_ret_to_host().
+ *
+ * Returns:	Next address after end of written function.
+ */
+void *kvm_mips_build_vcpu_run(void *addr)
+{
+	u32 *p = addr;
+	unsigned int i;
+
+	/*
+	 * A0: vcpu
+	 */
+
+	/* k0/k1 not being used in host kernel context */
+	UASM_i_ADDIU(&p, K1, SP, -(int)sizeof(struct pt_regs));
+	for (i = 16; i < 32; ++i) {
+		if (i == 24)
+			i = 28;
+		UASM_i_SW(&p, i, offsetof(struct pt_regs, regs[i]), K1);
+	}
+
+	/* Save host status */
+	uasm_i_mfc0(&p, V0, C0_STATUS);
+	UASM_i_SW(&p, V0, offsetof(struct pt_regs, cp0_status), K1);
+
+	/* Save scratch registers, will be used to store pointer to vcpu etc */
+	kvm_mips_build_save_scratch(&p, V1, K1);
+
+	/* VCPU scratch register has pointer to vcpu */
+	UASM_i_MTC0(&p, A0, scratch_vcpu[0], scratch_vcpu[1]);
+
+	/* Offset into vcpu->arch */
+	UASM_i_ADDIU(&p, K1, A0, offsetof(struct kvm_vcpu, arch));
+
+	/*
+	 * Save the host stack to VCPU, used for exception processing
+	 * when we exit from the Guest
+	 */
+	UASM_i_SW(&p, SP, offsetof(struct kvm_vcpu_arch, host_stack), K1);
+
+	/* Save the kernel gp as well */
+	UASM_i_SW(&p, GP, offsetof(struct kvm_vcpu_arch, host_gp), K1);
+
+	/*
+	 * Setup status register for running the guest in UM, interrupts
+	 * are disabled
+	 */
+	UASM_i_LA(&p, K0, ST0_EXL | KSU_USER | ST0_BEV | ST0_KX_IF_64);
+	uasm_i_mtc0(&p, K0, C0_STATUS);
+	uasm_i_ehb(&p);
+
+	/* load up the new EBASE */
+	UASM_i_LW(&p, K0, offsetof(struct kvm_vcpu_arch, guest_ebase), K1);
+	build_set_exc_base(&p, K0);
+
+	/*
+	 * Now that the new EBASE has been loaded, unset BEV, set
+	 * interrupt mask as it was but make sure that timer interrupts
+	 * are enabled
+	 */
+	uasm_i_addiu(&p, K0, ZERO, ST0_EXL | KSU_USER | ST0_IE | ST0_KX_IF_64);
+	uasm_i_andi(&p, V0, V0, ST0_IM);
+	uasm_i_or(&p, K0, K0, V0);
+	uasm_i_mtc0(&p, K0, C0_STATUS);
+	uasm_i_ehb(&p);
+
+	p = kvm_mips_build_enter_guest(p);
+
+	return p;
+}
+
+/**
+ * kvm_mips_build_enter_guest() - Assemble code to resume guest execution.
+ * @addr:	Address to start writing code.
+ *
+ * Assemble the code to resume guest execution. This code is common between the
+ * initial entry into the guest from the host, and returning from the exit
+ * handler back to the guest.
+ *
+ * Returns:	Next address after end of written function.
+ */
+static void *kvm_mips_build_enter_guest(void *addr)
+{
+	u32 *p = addr;
+	unsigned int i;
+	struct uasm_label labels[2];
+	struct uasm_reloc relocs[2];
+	struct uasm_label __maybe_unused *l = labels;
+	struct uasm_reloc __maybe_unused *r = relocs;
+
+	memset(labels, 0, sizeof(labels));
+	memset(relocs, 0, sizeof(relocs));
+
+	/* Set Guest EPC */
+	UASM_i_LW(&p, T0, offsetof(struct kvm_vcpu_arch, pc), K1);
+	UASM_i_MTC0(&p, T0, C0_EPC);
+
+	/* Save normal linux process pgd (VZ guarantees pgd_reg is set) */
+	if (cpu_has_ldpte)
+		UASM_i_MFC0(&p, K0, C0_PWBASE);
+	else
+		UASM_i_MFC0(&p, K0, c0_kscratch(), pgd_reg);
+	UASM_i_SW(&p, K0, offsetof(struct kvm_vcpu_arch, host_pgd), K1);
+
+	/*
+	 * Set up KVM GPA pgd.
+	 * This does roughly the same as TLBMISS_HANDLER_SETUP_PGD():
+	 * - call tlbmiss_handler_setup_pgd(mm->pgd)
+	 * - write mm->pgd into CP0_PWBase
+	 *
+	 * We keep S0 pointing at struct kvm so we can load the ASID below.
+	 */
+	UASM_i_LW(&p, S0, (int)offsetof(struct kvm_vcpu, kvm) -
+			  (int)offsetof(struct kvm_vcpu, arch), K1);
+	UASM_i_LW(&p, A0, offsetof(struct kvm, arch.gpa_mm.pgd), S0);
+	UASM_i_LA(&p, T9, (unsigned long)tlbmiss_handler_setup_pgd);
+	uasm_i_jalr(&p, RA, T9);
+	/* delay slot */
+	if (cpu_has_htw)
+		UASM_i_MTC0(&p, A0, C0_PWBASE);
+	else
+		uasm_i_nop(&p);
+
+	/* Set GM bit to setup eret to VZ guest context */
+	uasm_i_addiu(&p, V1, ZERO, 1);
+	uasm_i_mfc0(&p, K0, C0_GUESTCTL0);
+	uasm_i_ins(&p, K0, V1, MIPS_GCTL0_GM_SHIFT, 1);
+	uasm_i_mtc0(&p, K0, C0_GUESTCTL0);
+
+	if (cpu_has_guestid) {
+		/*
+		 * Set root mode GuestID, so that root TLB refill handler can
+		 * use the correct GuestID in the root TLB.
+		 */
+
+		/* Get current GuestID */
+		uasm_i_mfc0(&p, T0, C0_GUESTCTL1);
+		/* Set GuestCtl1.RID = GuestCtl1.ID */
+		uasm_i_ext(&p, T1, T0, MIPS_GCTL1_ID_SHIFT,
+			   MIPS_GCTL1_ID_WIDTH);
+		uasm_i_ins(&p, T0, T1, MIPS_GCTL1_RID_SHIFT,
+			   MIPS_GCTL1_RID_WIDTH);
+		uasm_i_mtc0(&p, T0, C0_GUESTCTL1);
+
+		/* GuestID handles dealiasing so we don't need to touch ASID */
+		goto skip_asid_restore;
+	}
+
+	/* Root ASID Dealias (RAD) */
+
+	/* Save host ASID */
+	UASM_i_MFC0(&p, K0, C0_ENTRYHI);
+	UASM_i_SW(&p, K0, offsetof(struct kvm_vcpu_arch, host_entryhi),
+		  K1);
+
+	/* Set the root ASID for the Guest */
+	UASM_i_ADDIU(&p, T1, S0,
+		     offsetof(struct kvm, arch.gpa_mm.context.asid));
+
+	/* t1: contains the base of the ASID array, need to get the cpu id  */
+	/* smp_processor_id */
+	uasm_i_lw(&p, T2, offsetof(struct thread_info, cpu), GP);
+	/* index the ASID array */
+	uasm_i_sll(&p, T2, T2, ilog2(sizeof(long)));
+	UASM_i_ADDU(&p, T3, T1, T2);
+	UASM_i_LW(&p, K0, 0, T3);
+#ifdef CONFIG_MIPS_ASID_BITS_VARIABLE
+	/*
+	 * reuse ASID array offset
+	 * cpuinfo_mips is a multiple of sizeof(long)
+	 */
+	uasm_i_addiu(&p, T3, ZERO, sizeof(struct cpuinfo_mips)/sizeof(long));
+	uasm_i_mul(&p, T2, T2, T3);
+
+	UASM_i_LA_mostly(&p, AT, (long)&cpu_data[0].asid_mask);
+	UASM_i_ADDU(&p, AT, AT, T2);
+	UASM_i_LW(&p, T2, uasm_rel_lo((long)&cpu_data[0].asid_mask), AT);
+	uasm_i_and(&p, K0, K0, T2);
+#else
+	uasm_i_andi(&p, K0, K0, MIPS_ENTRYHI_ASID);
+#endif
+
+	/* Set up KVM VZ root ASID (!guestid) */
+	uasm_i_mtc0(&p, K0, C0_ENTRYHI);
+skip_asid_restore:
+	uasm_i_ehb(&p);
+
+	/* Disable RDHWR access */
+	uasm_i_mtc0(&p, ZERO, C0_HWRENA);
+
+	/* load the guest context from VCPU and return */
+	for (i = 1; i < 32; ++i) {
+		/* Guest k0/k1 loaded later */
+		if (i == K0 || i == K1)
+			continue;
+		UASM_i_LW(&p, i, offsetof(struct kvm_vcpu_arch, gprs[i]), K1);
+	}
+
+#ifndef CONFIG_CPU_MIPSR6
+	/* Restore hi/lo */
+	UASM_i_LW(&p, K0, offsetof(struct kvm_vcpu_arch, hi), K1);
+	uasm_i_mthi(&p, K0);
+
+	UASM_i_LW(&p, K0, offsetof(struct kvm_vcpu_arch, lo), K1);
+	uasm_i_mtlo(&p, K0);
+#endif
+
+	/* Restore the guest's k0/k1 registers */
+	UASM_i_LW(&p, K0, offsetof(struct kvm_vcpu_arch, gprs[K0]), K1);
+	UASM_i_LW(&p, K1, offsetof(struct kvm_vcpu_arch, gprs[K1]), K1);
+
+	/* Jump to guest */
+	uasm_i_eret(&p);
+
+	uasm_resolve_relocs(relocs, labels);
+
+	return p;
+}
+
+/**
+ * kvm_mips_build_tlb_refill_exception() - Assemble TLB refill handler.
+ * @addr:	Address to start writing code.
+ * @handler:	Address of common handler (within range of @addr).
+ *
+ * Assemble TLB refill exception fast path handler for guest execution.
+ *
+ * Returns:	Next address after end of written function.
+ */
+void *kvm_mips_build_tlb_refill_exception(void *addr, void *handler)
+{
+	u32 *p = addr;
+	struct uasm_label labels[2];
+	struct uasm_reloc relocs[2];
+#ifndef CONFIG_CPU_LOONGSON64
+	struct uasm_label *l = labels;
+	struct uasm_reloc *r = relocs;
+#endif
+
+	memset(labels, 0, sizeof(labels));
+	memset(relocs, 0, sizeof(relocs));
+
+	/* Save guest k1 into scratch register */
+	UASM_i_MTC0(&p, K1, scratch_tmp[0], scratch_tmp[1]);
+
+	/* Get the VCPU pointer from the VCPU scratch register */
+	UASM_i_MFC0(&p, K1, scratch_vcpu[0], scratch_vcpu[1]);
+
+	/* Save guest k0 into VCPU structure */
+	UASM_i_SW(&p, K0, offsetof(struct kvm_vcpu, arch.gprs[K0]), K1);
+
+	/*
+	 * Some of the common tlbex code uses current_cpu_type(). For KVM we
+	 * assume symmetry and just disable preemption to silence the warning.
+	 */
+	preempt_disable();
+
+#ifdef CONFIG_CPU_LOONGSON64
+	UASM_i_MFC0(&p, K1, C0_PGD);
+	uasm_i_lddir(&p, K0, K1, 3);  /* global page dir */
+#ifndef __PAGETABLE_PMD_FOLDED
+	uasm_i_lddir(&p, K1, K0, 1);  /* middle page dir */
+#endif
+	uasm_i_ldpte(&p, K1, 0);      /* even */
+	uasm_i_ldpte(&p, K1, 1);      /* odd */
+	uasm_i_tlbwr(&p);
+#else
+	/*
+	 * Now for the actual refill bit. A lot of this can be common with the
+	 * Linux TLB refill handler, however we don't need to handle so many
+	 * cases. We only need to handle user mode refills, and user mode runs
+	 * with 32-bit addressing.
+	 *
+	 * Therefore the branch to label_vmalloc generated by build_get_pmde64()
+	 * that isn't resolved should never actually get taken and is harmless
+	 * to leave in place for now.
+	 */
+
+#ifdef CONFIG_64BIT
+	build_get_pmde64(&p, &l, &r, K0, K1); /* get pmd in K1 */
+#else
+	build_get_pgde32(&p, K0, K1); /* get pgd in K1 */
+#endif
+
+	/* we don't support huge pages yet */
+
+	build_get_ptep(&p, K0, K1);
+	build_update_entries(&p, K0, K1);
+	build_tlb_write_entry(&p, &l, &r, tlb_random);
+#endif
+
+	preempt_enable();
+
+	/* Get the VCPU pointer from the VCPU scratch register again */
+	UASM_i_MFC0(&p, K1, scratch_vcpu[0], scratch_vcpu[1]);
+
+	/* Restore the guest's k0/k1 registers */
+	UASM_i_LW(&p, K0, offsetof(struct kvm_vcpu, arch.gprs[K0]), K1);
+	uasm_i_ehb(&p);
+	UASM_i_MFC0(&p, K1, scratch_tmp[0], scratch_tmp[1]);
+
+	/* Jump to guest */
+	uasm_i_eret(&p);
+
+	return p;
+}
+
+/**
+ * kvm_mips_build_exception() - Assemble first level guest exception handler.
+ * @addr:	Address to start writing code.
+ * @handler:	Address of common handler (within range of @addr).
+ *
+ * Assemble exception vector code for guest execution. The generated vector will
+ * branch to the common exception handler generated by kvm_mips_build_exit().
+ *
+ * Returns:	Next address after end of written function.
+ */
+void *kvm_mips_build_exception(void *addr, void *handler)
+{
+	u32 *p = addr;
+	struct uasm_label labels[2];
+	struct uasm_reloc relocs[2];
+	struct uasm_label *l = labels;
+	struct uasm_reloc *r = relocs;
+
+	memset(labels, 0, sizeof(labels));
+	memset(relocs, 0, sizeof(relocs));
+
+	/* Save guest k1 into scratch register */
+	UASM_i_MTC0(&p, K1, scratch_tmp[0], scratch_tmp[1]);
+
+	/* Get the VCPU pointer from the VCPU scratch register */
+	UASM_i_MFC0(&p, K1, scratch_vcpu[0], scratch_vcpu[1]);
+	UASM_i_ADDIU(&p, K1, K1, offsetof(struct kvm_vcpu, arch));
+
+	/* Save guest k0 into VCPU structure */
+	UASM_i_SW(&p, K0, offsetof(struct kvm_vcpu_arch, gprs[K0]), K1);
+
+	/* Branch to the common handler */
+	uasm_il_b(&p, &r, label_exit_common);
+	 uasm_i_nop(&p);
+
+	uasm_l_exit_common(&l, handler);
+	uasm_resolve_relocs(relocs, labels);
+
+	return p;
+}
+
+/**
+ * kvm_mips_build_exit() - Assemble common guest exit handler.
+ * @addr:	Address to start writing code.
+ *
+ * Assemble the generic guest exit handling code. This is called by the
+ * exception vectors (generated by kvm_mips_build_exception()), and calls
+ * kvm_mips_handle_exit(), then either resumes the guest or returns to the host
+ * depending on the return value.
+ *
+ * Returns:	Next address after end of written function.
+ */
+void *kvm_mips_build_exit(void *addr)
+{
+	u32 *p = addr;
+	unsigned int i;
+	struct uasm_label labels[3];
+	struct uasm_reloc relocs[3];
+	struct uasm_label *l = labels;
+	struct uasm_reloc *r = relocs;
+
+	memset(labels, 0, sizeof(labels));
+	memset(relocs, 0, sizeof(relocs));
+
+	/*
+	 * Generic Guest exception handler. We end up here when the guest
+	 * does something that causes a trap to kernel mode.
+	 *
+	 * Both k0/k1 registers will have already been saved (k0 into the vcpu
+	 * structure, and k1 into the scratch_tmp register).
+	 *
+	 * The k1 register will already contain the kvm_vcpu_arch pointer.
+	 */
+
+	/* Start saving Guest context to VCPU */
+	for (i = 0; i < 32; ++i) {
+		/* Guest k0/k1 saved later */
+		if (i == K0 || i == K1)
+			continue;
+		UASM_i_SW(&p, i, offsetof(struct kvm_vcpu_arch, gprs[i]), K1);
+	}
+
+#ifndef CONFIG_CPU_MIPSR6
+	/* We need to save hi/lo and restore them on the way out */
+	uasm_i_mfhi(&p, T0);
+	UASM_i_SW(&p, T0, offsetof(struct kvm_vcpu_arch, hi), K1);
+
+	uasm_i_mflo(&p, T0);
+	UASM_i_SW(&p, T0, offsetof(struct kvm_vcpu_arch, lo), K1);
+#endif
+
+	/* Finally save guest k1 to VCPU */
+	uasm_i_ehb(&p);
+	UASM_i_MFC0(&p, T0, scratch_tmp[0], scratch_tmp[1]);
+	UASM_i_SW(&p, T0, offsetof(struct kvm_vcpu_arch, gprs[K1]), K1);
+
+	/* Now that context has been saved, we can use other registers */
+
+	/* Restore vcpu */
+	UASM_i_MFC0(&p, S0, scratch_vcpu[0], scratch_vcpu[1]);
+
+	/*
+	 * Save Host level EPC, BadVaddr and Cause to VCPU, useful to process
+	 * the exception
+	 */
+	UASM_i_MFC0(&p, K0, C0_EPC);
+	UASM_i_SW(&p, K0, offsetof(struct kvm_vcpu_arch, pc), K1);
+
+	UASM_i_MFC0(&p, K0, C0_BADVADDR);
+	UASM_i_SW(&p, K0, offsetof(struct kvm_vcpu_arch, host_cp0_badvaddr),
+		  K1);
+
+	uasm_i_mfc0(&p, K0, C0_CAUSE);
+	uasm_i_sw(&p, K0, offsetof(struct kvm_vcpu_arch, host_cp0_cause), K1);
+
+	if (cpu_has_badinstr) {
+		uasm_i_mfc0(&p, K0, C0_BADINSTR);
+		uasm_i_sw(&p, K0, offsetof(struct kvm_vcpu_arch,
+					   host_cp0_badinstr), K1);
+	}
+
+	if (cpu_has_badinstrp) {
+		uasm_i_mfc0(&p, K0, C0_BADINSTRP);
+		uasm_i_sw(&p, K0, offsetof(struct kvm_vcpu_arch,
+					   host_cp0_badinstrp), K1);
+	}
+
+	/* Now restore the host state just enough to run the handlers */
+
+	/* Switch EBASE to the one used by Linux */
+	/* load up the host EBASE */
+	uasm_i_mfc0(&p, V0, C0_STATUS);
+
+	uasm_i_lui(&p, AT, ST0_BEV >> 16);
+	uasm_i_or(&p, K0, V0, AT);
+
+	uasm_i_mtc0(&p, K0, C0_STATUS);
+	uasm_i_ehb(&p);
+
+	UASM_i_LA_mostly(&p, K0, (long)&ebase);
+	UASM_i_LW(&p, K0, uasm_rel_lo((long)&ebase), K0);
+	build_set_exc_base(&p, K0);
+
+	if (raw_cpu_has_fpu) {
+		/*
+		 * If FPU is enabled, save FCR31 and clear it so that later
+		 * ctc1's don't trigger FPE for pending exceptions.
+		 */
+		uasm_i_lui(&p, AT, ST0_CU1 >> 16);
+		uasm_i_and(&p, V1, V0, AT);
+		uasm_il_beqz(&p, &r, V1, label_fpu_1);
+		 uasm_i_nop(&p);
+		uasm_i_cfc1(&p, T0, 31);
+		uasm_i_sw(&p, T0, offsetof(struct kvm_vcpu_arch, fpu.fcr31),
+			  K1);
+		uasm_i_ctc1(&p, ZERO, 31);
+		uasm_l_fpu_1(&l, p);
+	}
+
+	if (cpu_has_msa) {
+		/*
+		 * If MSA is enabled, save MSACSR and clear it so that later
+		 * instructions don't trigger MSAFPE for pending exceptions.
+		 */
+		uasm_i_mfc0(&p, T0, C0_CONFIG5);
+		uasm_i_ext(&p, T0, T0, 27, 1); /* MIPS_CONF5_MSAEN */
+		uasm_il_beqz(&p, &r, T0, label_msa_1);
+		 uasm_i_nop(&p);
+		uasm_i_cfcmsa(&p, T0, MSA_CSR);
+		uasm_i_sw(&p, T0, offsetof(struct kvm_vcpu_arch, fpu.msacsr),
+			  K1);
+		uasm_i_ctcmsa(&p, MSA_CSR, ZERO);
+		uasm_l_msa_1(&l, p);
+	}
+
+	/* Restore host ASID */
+	if (!cpu_has_guestid) {
+		UASM_i_LW(&p, K0, offsetof(struct kvm_vcpu_arch, host_entryhi),
+			  K1);
+		UASM_i_MTC0(&p, K0, C0_ENTRYHI);
+	}
+
+	/*
+	 * Set up normal Linux process pgd.
+	 * This does roughly the same as TLBMISS_HANDLER_SETUP_PGD():
+	 * - call tlbmiss_handler_setup_pgd(mm->pgd)
+	 * - write mm->pgd into CP0_PWBase
+	 */
+	UASM_i_LW(&p, A0,
+		  offsetof(struct kvm_vcpu_arch, host_pgd), K1);
+	UASM_i_LA(&p, T9, (unsigned long)tlbmiss_handler_setup_pgd);
+	uasm_i_jalr(&p, RA, T9);
+	/* delay slot */
+	if (cpu_has_htw)
+		UASM_i_MTC0(&p, A0, C0_PWBASE);
+	else
+		uasm_i_nop(&p);
+
+	/* Clear GM bit so we don't enter guest mode when EXL is cleared */
+	uasm_i_mfc0(&p, K0, C0_GUESTCTL0);
+	uasm_i_ins(&p, K0, ZERO, MIPS_GCTL0_GM_SHIFT, 1);
+	uasm_i_mtc0(&p, K0, C0_GUESTCTL0);
+
+	/* Save GuestCtl0 so we can access GExcCode after CPU migration */
+	uasm_i_sw(&p, K0,
+		  offsetof(struct kvm_vcpu_arch, host_cp0_guestctl0), K1);
+
+	if (cpu_has_guestid) {
+		/*
+		 * Clear root mode GuestID, so that root TLB operations use the
+		 * root GuestID in the root TLB.
+		 */
+		uasm_i_mfc0(&p, T0, C0_GUESTCTL1);
+		/* Set GuestCtl1.RID = MIPS_GCTL1_ROOT_GUESTID (i.e. 0) */
+		uasm_i_ins(&p, T0, ZERO, MIPS_GCTL1_RID_SHIFT,
+			   MIPS_GCTL1_RID_WIDTH);
+		uasm_i_mtc0(&p, T0, C0_GUESTCTL1);
+	}
+
+	/* Now that the new EBASE has been loaded, unset BEV and KSU_USER */
+	uasm_i_addiu(&p, AT, ZERO, ~(ST0_EXL | KSU_USER | ST0_IE));
+	uasm_i_and(&p, V0, V0, AT);
+	uasm_i_lui(&p, AT, ST0_CU0 >> 16);
+	uasm_i_or(&p, V0, V0, AT);
+#ifdef CONFIG_64BIT
+	uasm_i_ori(&p, V0, V0, ST0_SX | ST0_UX);
+#endif
+	uasm_i_mtc0(&p, V0, C0_STATUS);
+	uasm_i_ehb(&p);
+
+	/* Load up host GP */
+	UASM_i_LW(&p, GP, offsetof(struct kvm_vcpu_arch, host_gp), K1);
+
+	/* Need a stack before we can jump to "C" */
+	UASM_i_LW(&p, SP, offsetof(struct kvm_vcpu_arch, host_stack), K1);
+
+	/* Saved host state */
+	UASM_i_ADDIU(&p, SP, SP, -(int)sizeof(struct pt_regs));
+
+	/*
+	 * XXXKYMA do we need to load the host ASID, maybe not because the
+	 * kernel entries are marked GLOBAL, need to verify
+	 */
+
+	/* Restore host scratch registers, as we'll have clobbered them */
+	kvm_mips_build_restore_scratch(&p, K0, SP);
+
+	/* Restore RDHWR access */
+	UASM_i_LA_mostly(&p, K0, (long)&hwrena);
+	uasm_i_lw(&p, K0, uasm_rel_lo((long)&hwrena), K0);
+	uasm_i_mtc0(&p, K0, C0_HWRENA);
+
+	/* Jump to handler */
+	/*
+	 * XXXKYMA: not sure if this is safe, how large is the stack??
+	 * Now jump to the kvm_mips_handle_exit() to see if we can deal
+	 * with this in the kernel
+	 */
+	uasm_i_move(&p, A0, S0);
+	UASM_i_LA(&p, T9, (unsigned long)kvm_mips_handle_exit);
+	uasm_i_jalr(&p, RA, T9);
+	 UASM_i_ADDIU(&p, SP, SP, -CALLFRAME_SIZ);
+
+	uasm_resolve_relocs(relocs, labels);
+
+	p = kvm_mips_build_ret_from_exit(p);
+
+	return p;
+}
+
+/**
+ * kvm_mips_build_ret_from_exit() - Assemble guest exit return handler.
+ * @addr:	Address to start writing code.
+ *
+ * Assemble the code to handle the return from kvm_mips_handle_exit(), either
+ * resuming the guest or returning to the host depending on the return value.
+ *
+ * Returns:	Next address after end of written function.
+ */
+static void *kvm_mips_build_ret_from_exit(void *addr)
+{
+	u32 *p = addr;
+	struct uasm_label labels[2];
+	struct uasm_reloc relocs[2];
+	struct uasm_label *l = labels;
+	struct uasm_reloc *r = relocs;
+
+	memset(labels, 0, sizeof(labels));
+	memset(relocs, 0, sizeof(relocs));
+
+	/* Return from handler Make sure interrupts are disabled */
+	uasm_i_di(&p, ZERO);
+	uasm_i_ehb(&p);
+
+	/*
+	 * XXXKYMA: k0/k1 could have been blown away if we processed
+	 * an exception while we were handling the exception from the
+	 * guest, reload k1
+	 */
+
+	uasm_i_move(&p, K1, S0);
+	UASM_i_ADDIU(&p, K1, K1, offsetof(struct kvm_vcpu, arch));
+
+	/*
+	 * Check return value, should tell us if we are returning to the
+	 * host (handle I/O etc)or resuming the guest
+	 */
+	uasm_i_andi(&p, T0, V0, RESUME_HOST);
+	uasm_il_bnez(&p, &r, T0, label_return_to_host);
+	 uasm_i_nop(&p);
+
+	p = kvm_mips_build_ret_to_guest(p);
+
+	uasm_l_return_to_host(&l, p);
+	p = kvm_mips_build_ret_to_host(p);
+
+	uasm_resolve_relocs(relocs, labels);
+
+	return p;
+}
+
+/**
+ * kvm_mips_build_ret_to_guest() - Assemble code to return to the guest.
+ * @addr:	Address to start writing code.
+ *
+ * Assemble the code to handle return from the guest exit handler
+ * (kvm_mips_handle_exit()) back to the guest.
+ *
+ * Returns:	Next address after end of written function.
+ */
+static void *kvm_mips_build_ret_to_guest(void *addr)
+{
+	u32 *p = addr;
+
+	/* Put the saved pointer to vcpu (s0) back into the scratch register */
+	UASM_i_MTC0(&p, S0, scratch_vcpu[0], scratch_vcpu[1]);
+
+	/* Load up the Guest EBASE to minimize the window where BEV is set */
+	UASM_i_LW(&p, T0, offsetof(struct kvm_vcpu_arch, guest_ebase), K1);
+
+	/* Switch EBASE back to the one used by KVM */
+	uasm_i_mfc0(&p, V1, C0_STATUS);
+	uasm_i_lui(&p, AT, ST0_BEV >> 16);
+	uasm_i_or(&p, K0, V1, AT);
+	uasm_i_mtc0(&p, K0, C0_STATUS);
+	uasm_i_ehb(&p);
+	build_set_exc_base(&p, T0);
+
+	/* Setup status register for running guest in UM */
+	uasm_i_ori(&p, V1, V1, ST0_EXL | KSU_USER | ST0_IE);
+	UASM_i_LA(&p, AT, ~(ST0_CU0 | ST0_MX | ST0_SX | ST0_UX));
+	uasm_i_and(&p, V1, V1, AT);
+	uasm_i_mtc0(&p, V1, C0_STATUS);
+	uasm_i_ehb(&p);
+
+	p = kvm_mips_build_enter_guest(p);
+
+	return p;
+}
+
+/**
+ * kvm_mips_build_ret_to_host() - Assemble code to return to the host.
+ * @addr:	Address to start writing code.
+ *
+ * Assemble the code to handle return from the guest exit handler
+ * (kvm_mips_handle_exit()) back to the host, i.e. to the caller of the vcpu_run
+ * function generated by kvm_mips_build_vcpu_run().
+ *
+ * Returns:	Next address after end of written function.
+ */
+static void *kvm_mips_build_ret_to_host(void *addr)
+{
+	u32 *p = addr;
+	unsigned int i;
+
+	/* EBASE is already pointing to Linux */
+	UASM_i_LW(&p, K1, offsetof(struct kvm_vcpu_arch, host_stack), K1);
+	UASM_i_ADDIU(&p, K1, K1, -(int)sizeof(struct pt_regs));
+
+	/*
+	 * r2/v0 is the return code, shift it down by 2 (arithmetic)
+	 * to recover the err code
+	 */
+	uasm_i_sra(&p, K0, V0, 2);
+	uasm_i_move(&p, V0, K0);
+
+	/* Load context saved on the host stack */
+	for (i = 16; i < 31; ++i) {
+		if (i == 24)
+			i = 28;
+		UASM_i_LW(&p, i, offsetof(struct pt_regs, regs[i]), K1);
+	}
+
+	/* Restore RDHWR access */
+	UASM_i_LA_mostly(&p, K0, (long)&hwrena);
+	uasm_i_lw(&p, K0, uasm_rel_lo((long)&hwrena), K0);
+	uasm_i_mtc0(&p, K0, C0_HWRENA);
+
+	/* Restore RA, which is the address we will return to */
+	UASM_i_LW(&p, RA, offsetof(struct pt_regs, regs[RA]), K1);
+	uasm_i_jr(&p, RA);
+	 uasm_i_nop(&p);
+
+	return p;
+}
+
diff --git a/arch/mips/kvm/fpu.S b/arch/mips/kvm/fpu.S
new file mode 100644
index 000000000..16f17c639
--- /dev/null
+++ b/arch/mips/kvm/fpu.S
@@ -0,0 +1,125 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * FPU context handling code for KVM.
+ *
+ * Copyright (C) 2015 Imagination Technologies Ltd.
+ */
+
+#include <asm/asm.h>
+#include <asm/asm-offsets.h>
+#include <asm/fpregdef.h>
+#include <asm/mipsregs.h>
+#include <asm/regdef.h>
+
+/* preprocessor replaces the fp in ".set fp=64" with $30 otherwise */
+#undef fp
+
+	.set	noreorder
+	.set	noat
+
+LEAF(__kvm_save_fpu)
+	.set	push
+	SET_HARDFLOAT
+	.set	fp=64
+	mfc0	t0, CP0_STATUS
+	sll     t0, t0, 5			# is Status.FR set?
+	bgez    t0, 1f				# no: skip odd doubles
+	 nop
+	sdc1	$f1,  VCPU_FPR1(a0)
+	sdc1	$f3,  VCPU_FPR3(a0)
+	sdc1	$f5,  VCPU_FPR5(a0)
+	sdc1	$f7,  VCPU_FPR7(a0)
+	sdc1	$f9,  VCPU_FPR9(a0)
+	sdc1	$f11, VCPU_FPR11(a0)
+	sdc1	$f13, VCPU_FPR13(a0)
+	sdc1	$f15, VCPU_FPR15(a0)
+	sdc1	$f17, VCPU_FPR17(a0)
+	sdc1	$f19, VCPU_FPR19(a0)
+	sdc1	$f21, VCPU_FPR21(a0)
+	sdc1	$f23, VCPU_FPR23(a0)
+	sdc1	$f25, VCPU_FPR25(a0)
+	sdc1	$f27, VCPU_FPR27(a0)
+	sdc1	$f29, VCPU_FPR29(a0)
+	sdc1	$f31, VCPU_FPR31(a0)
+1:	sdc1	$f0,  VCPU_FPR0(a0)
+	sdc1	$f2,  VCPU_FPR2(a0)
+	sdc1	$f4,  VCPU_FPR4(a0)
+	sdc1	$f6,  VCPU_FPR6(a0)
+	sdc1	$f8,  VCPU_FPR8(a0)
+	sdc1	$f10, VCPU_FPR10(a0)
+	sdc1	$f12, VCPU_FPR12(a0)
+	sdc1	$f14, VCPU_FPR14(a0)
+	sdc1	$f16, VCPU_FPR16(a0)
+	sdc1	$f18, VCPU_FPR18(a0)
+	sdc1	$f20, VCPU_FPR20(a0)
+	sdc1	$f22, VCPU_FPR22(a0)
+	sdc1	$f24, VCPU_FPR24(a0)
+	sdc1	$f26, VCPU_FPR26(a0)
+	sdc1	$f28, VCPU_FPR28(a0)
+	jr	ra
+	 sdc1	$f30, VCPU_FPR30(a0)
+	.set	pop
+	END(__kvm_save_fpu)
+
+LEAF(__kvm_restore_fpu)
+	.set	push
+	SET_HARDFLOAT
+	.set	fp=64
+	mfc0	t0, CP0_STATUS
+	sll     t0, t0, 5			# is Status.FR set?
+	bgez    t0, 1f				# no: skip odd doubles
+	 nop
+	ldc1	$f1,  VCPU_FPR1(a0)
+	ldc1	$f3,  VCPU_FPR3(a0)
+	ldc1	$f5,  VCPU_FPR5(a0)
+	ldc1	$f7,  VCPU_FPR7(a0)
+	ldc1	$f9,  VCPU_FPR9(a0)
+	ldc1	$f11, VCPU_FPR11(a0)
+	ldc1	$f13, VCPU_FPR13(a0)
+	ldc1	$f15, VCPU_FPR15(a0)
+	ldc1	$f17, VCPU_FPR17(a0)
+	ldc1	$f19, VCPU_FPR19(a0)
+	ldc1	$f21, VCPU_FPR21(a0)
+	ldc1	$f23, VCPU_FPR23(a0)
+	ldc1	$f25, VCPU_FPR25(a0)
+	ldc1	$f27, VCPU_FPR27(a0)
+	ldc1	$f29, VCPU_FPR29(a0)
+	ldc1	$f31, VCPU_FPR31(a0)
+1:	ldc1	$f0,  VCPU_FPR0(a0)
+	ldc1	$f2,  VCPU_FPR2(a0)
+	ldc1	$f4,  VCPU_FPR4(a0)
+	ldc1	$f6,  VCPU_FPR6(a0)
+	ldc1	$f8,  VCPU_FPR8(a0)
+	ldc1	$f10, VCPU_FPR10(a0)
+	ldc1	$f12, VCPU_FPR12(a0)
+	ldc1	$f14, VCPU_FPR14(a0)
+	ldc1	$f16, VCPU_FPR16(a0)
+	ldc1	$f18, VCPU_FPR18(a0)
+	ldc1	$f20, VCPU_FPR20(a0)
+	ldc1	$f22, VCPU_FPR22(a0)
+	ldc1	$f24, VCPU_FPR24(a0)
+	ldc1	$f26, VCPU_FPR26(a0)
+	ldc1	$f28, VCPU_FPR28(a0)
+	jr	ra
+	 ldc1	$f30, VCPU_FPR30(a0)
+	.set	pop
+	END(__kvm_restore_fpu)
+
+LEAF(__kvm_restore_fcsr)
+	.set	push
+	SET_HARDFLOAT
+	lw	t0, VCPU_FCR31(a0)
+	/*
+	 * The ctc1 must stay at this offset in __kvm_restore_fcsr.
+	 * See kvm_mips_csr_die_notify() which handles t0 containing a value
+	 * which triggers an FP Exception, which must be stepped over and
+	 * ignored since the set cause bits must remain there for the guest.
+	 */
+	ctc1	t0, fcr31
+	jr	ra
+	 nop
+	.set	pop
+	END(__kvm_restore_fcsr)
diff --git a/arch/mips/kvm/hypcall.c b/arch/mips/kvm/hypcall.c
new file mode 100644
index 000000000..830634351
--- /dev/null
+++ b/arch/mips/kvm/hypcall.c
@@ -0,0 +1,53 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * KVM/MIPS: Hypercall handling.
+ *
+ * Copyright (C) 2015  Imagination Technologies Ltd.
+ */
+
+#include <linux/kernel.h>
+#include <linux/kvm_host.h>
+#include <linux/kvm_para.h>
+
+#define MAX_HYPCALL_ARGS	4
+
+enum emulation_result kvm_mips_emul_hypcall(struct kvm_vcpu *vcpu,
+					    union mips_instruction inst)
+{
+	unsigned int code = (inst.co_format.code >> 5) & 0x3ff;
+
+	kvm_debug("[%#lx] HYPCALL %#03x\n", vcpu->arch.pc, code);
+
+	switch (code) {
+	case 0:
+		return EMULATE_HYPERCALL;
+	default:
+		return EMULATE_FAIL;
+	};
+}
+
+static int kvm_mips_hypercall(struct kvm_vcpu *vcpu, unsigned long num,
+			      const unsigned long *args, unsigned long *hret)
+{
+	/* Report unimplemented hypercall to guest */
+	*hret = -KVM_ENOSYS;
+	return RESUME_GUEST;
+}
+
+int kvm_mips_handle_hypcall(struct kvm_vcpu *vcpu)
+{
+	unsigned long num, args[MAX_HYPCALL_ARGS];
+
+	/* read hypcall number and arguments */
+	num = vcpu->arch.gprs[2];	/* v0 */
+	args[0] = vcpu->arch.gprs[4];	/* a0 */
+	args[1] = vcpu->arch.gprs[5];	/* a1 */
+	args[2] = vcpu->arch.gprs[6];	/* a2 */
+	args[3] = vcpu->arch.gprs[7];	/* a3 */
+
+	return kvm_mips_hypercall(vcpu, num,
+				  args, &vcpu->arch.gprs[2] /* v0 */);
+}
diff --git a/arch/mips/kvm/interrupt.c b/arch/mips/kvm/interrupt.c
new file mode 100644
index 000000000..027794227
--- /dev/null
+++ b/arch/mips/kvm/interrupt.c
@@ -0,0 +1,56 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * KVM/MIPS: Interrupt delivery
+ *
+ * Copyright (C) 2012  MIPS Technologies, Inc.  All rights reserved.
+ * Authors: Sanjay Lal <sanjayl@kymasys.com>
+ */
+
+#include <linux/errno.h>
+#include <linux/err.h>
+#include <linux/vmalloc.h>
+#include <linux/fs.h>
+#include <linux/memblock.h>
+#include <asm/page.h>
+#include <asm/cacheflush.h>
+
+#include <linux/kvm_host.h>
+
+#include "interrupt.h"
+
+void kvm_mips_deliver_interrupts(struct kvm_vcpu *vcpu, u32 cause)
+{
+	unsigned long *pending = &vcpu->arch.pending_exceptions;
+	unsigned long *pending_clr = &vcpu->arch.pending_exceptions_clr;
+	unsigned int priority;
+
+	if (!(*pending) && !(*pending_clr))
+		return;
+
+	priority = __ffs(*pending_clr);
+	while (priority <= MIPS_EXC_MAX) {
+		kvm_mips_callbacks->irq_clear(vcpu, priority, cause);
+
+		priority = find_next_bit(pending_clr,
+					 BITS_PER_BYTE * sizeof(*pending_clr),
+					 priority + 1);
+	}
+
+	priority = __ffs(*pending);
+	while (priority <= MIPS_EXC_MAX) {
+		kvm_mips_callbacks->irq_deliver(vcpu, priority, cause);
+
+		priority = find_next_bit(pending,
+					 BITS_PER_BYTE * sizeof(*pending),
+					 priority + 1);
+	}
+
+}
+
+int kvm_mips_pending_timer(struct kvm_vcpu *vcpu)
+{
+	return test_bit(MIPS_EXC_INT_TIMER, &vcpu->arch.pending_exceptions);
+}
diff --git a/arch/mips/kvm/interrupt.h b/arch/mips/kvm/interrupt.h
new file mode 100644
index 000000000..e529ea2bb
--- /dev/null
+++ b/arch/mips/kvm/interrupt.h
@@ -0,0 +1,39 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * KVM/MIPS: Interrupts
+ * Copyright (C) 2012  MIPS Technologies, Inc.  All rights reserved.
+ * Authors: Sanjay Lal <sanjayl@kymasys.com>
+ */
+
+/*
+ * MIPS Exception Priorities, exceptions (including interrupts) are queued up
+ * for the guest in the order specified by their priorities
+ */
+
+#define MIPS_EXC_RESET              0
+#define MIPS_EXC_SRESET             1
+#define MIPS_EXC_DEBUG_ST           2
+#define MIPS_EXC_DEBUG              3
+#define MIPS_EXC_DDB                4
+#define MIPS_EXC_NMI                5
+#define MIPS_EXC_MCHK               6
+#define MIPS_EXC_INT_TIMER          7
+#define MIPS_EXC_INT_IO_1           8
+#define MIPS_EXC_INT_IO_2           9
+#define MIPS_EXC_EXECUTE            10
+#define MIPS_EXC_INT_IPI_1          11
+#define MIPS_EXC_INT_IPI_2          12
+#define MIPS_EXC_MAX                13
+/* XXXSL More to follow */
+
+#define C_TI        (_ULCAST_(1) << 30)
+
+extern u32 *kvm_priority_to_irq;
+u32 kvm_irq_to_priority(u32 irq);
+
+int kvm_mips_pending_timer(struct kvm_vcpu *vcpu);
+
+void kvm_mips_deliver_interrupts(struct kvm_vcpu *vcpu, u32 cause);
diff --git a/arch/mips/kvm/loongson_ipi.c b/arch/mips/kvm/loongson_ipi.c
new file mode 100644
index 000000000..5d53f32d8
--- /dev/null
+++ b/arch/mips/kvm/loongson_ipi.c
@@ -0,0 +1,214 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Loongson-3 Virtual IPI interrupt support.
+ *
+ * Copyright (C) 2019  Loongson Technologies, Inc.  All rights reserved.
+ *
+ * Authors: Chen Zhu <zhuchen@loongson.cn>
+ * Authors: Huacai Chen <chenhc@lemote.com>
+ */
+
+#include <linux/kvm_host.h>
+
+#define IPI_BASE            0x3ff01000ULL
+
+#define CORE0_STATUS_OFF       0x000
+#define CORE0_EN_OFF           0x004
+#define CORE0_SET_OFF          0x008
+#define CORE0_CLEAR_OFF        0x00c
+#define CORE0_BUF_20           0x020
+#define CORE0_BUF_28           0x028
+#define CORE0_BUF_30           0x030
+#define CORE0_BUF_38           0x038
+
+#define CORE1_STATUS_OFF       0x100
+#define CORE1_EN_OFF           0x104
+#define CORE1_SET_OFF          0x108
+#define CORE1_CLEAR_OFF        0x10c
+#define CORE1_BUF_20           0x120
+#define CORE1_BUF_28           0x128
+#define CORE1_BUF_30           0x130
+#define CORE1_BUF_38           0x138
+
+#define CORE2_STATUS_OFF       0x200
+#define CORE2_EN_OFF           0x204
+#define CORE2_SET_OFF          0x208
+#define CORE2_CLEAR_OFF        0x20c
+#define CORE2_BUF_20           0x220
+#define CORE2_BUF_28           0x228
+#define CORE2_BUF_30           0x230
+#define CORE2_BUF_38           0x238
+
+#define CORE3_STATUS_OFF       0x300
+#define CORE3_EN_OFF           0x304
+#define CORE3_SET_OFF          0x308
+#define CORE3_CLEAR_OFF        0x30c
+#define CORE3_BUF_20           0x320
+#define CORE3_BUF_28           0x328
+#define CORE3_BUF_30           0x330
+#define CORE3_BUF_38           0x338
+
+static int loongson_vipi_read(struct loongson_kvm_ipi *ipi,
+				gpa_t addr, int len, void *val)
+{
+	uint32_t core = (addr >> 8) & 3;
+	uint32_t node = (addr >> 44) & 3;
+	uint32_t id = core + node * 4;
+	uint64_t offset = addr & 0xff;
+	void *pbuf;
+	struct ipi_state *s = &(ipi->ipistate[id]);
+
+	BUG_ON(offset & (len - 1));
+
+	switch (offset) {
+	case CORE0_STATUS_OFF:
+		*(uint64_t *)val = s->status;
+		break;
+
+	case CORE0_EN_OFF:
+		*(uint64_t *)val = s->en;
+		break;
+
+	case CORE0_SET_OFF:
+		*(uint64_t *)val = 0;
+		break;
+
+	case CORE0_CLEAR_OFF:
+		*(uint64_t *)val = 0;
+		break;
+
+	case CORE0_BUF_20 ... CORE0_BUF_38:
+		pbuf = (void *)s->buf + (offset - 0x20);
+		if (len == 8)
+			*(uint64_t *)val = *(uint64_t *)pbuf;
+		else /* Assume len == 4 */
+			*(uint32_t *)val = *(uint32_t *)pbuf;
+		break;
+
+	default:
+		pr_notice("%s with unknown addr %llx\n", __func__, addr);
+		break;
+	}
+
+	return 0;
+}
+
+static int loongson_vipi_write(struct loongson_kvm_ipi *ipi,
+				gpa_t addr, int len, const void *val)
+{
+	uint32_t core = (addr >> 8) & 3;
+	uint32_t node = (addr >> 44) & 3;
+	uint32_t id = core + node * 4;
+	uint64_t data, offset = addr & 0xff;
+	void *pbuf;
+	struct kvm *kvm = ipi->kvm;
+	struct kvm_mips_interrupt irq;
+	struct ipi_state *s = &(ipi->ipistate[id]);
+
+	data = *(uint64_t *)val;
+	BUG_ON(offset & (len - 1));
+
+	switch (offset) {
+	case CORE0_STATUS_OFF:
+		break;
+
+	case CORE0_EN_OFF:
+		s->en = data;
+		break;
+
+	case CORE0_SET_OFF:
+		s->status |= data;
+		irq.cpu = id;
+		irq.irq = 6;
+		kvm_vcpu_ioctl_interrupt(kvm_get_vcpu(kvm, id), &irq);
+		break;
+
+	case CORE0_CLEAR_OFF:
+		s->status &= ~data;
+		if (!s->status) {
+			irq.cpu = id;
+			irq.irq = -6;
+			kvm_vcpu_ioctl_interrupt(kvm_get_vcpu(kvm, id), &irq);
+		}
+		break;
+
+	case CORE0_BUF_20 ... CORE0_BUF_38:
+		pbuf = (void *)s->buf + (offset - 0x20);
+		if (len == 8)
+			*(uint64_t *)pbuf = (uint64_t)data;
+		else /* Assume len == 4 */
+			*(uint32_t *)pbuf = (uint32_t)data;
+		break;
+
+	default:
+		pr_notice("%s with unknown addr %llx\n", __func__, addr);
+		break;
+	}
+
+	return 0;
+}
+
+static int kvm_ipi_read(struct kvm_vcpu *vcpu, struct kvm_io_device *dev,
+			gpa_t addr, int len, void *val)
+{
+	unsigned long flags;
+	struct loongson_kvm_ipi *ipi;
+	struct ipi_io_device *ipi_device;
+
+	ipi_device = container_of(dev, struct ipi_io_device, device);
+	ipi = ipi_device->ipi;
+
+	spin_lock_irqsave(&ipi->lock, flags);
+	loongson_vipi_read(ipi, addr, len, val);
+	spin_unlock_irqrestore(&ipi->lock, flags);
+
+	return 0;
+}
+
+static int kvm_ipi_write(struct kvm_vcpu *vcpu, struct kvm_io_device *dev,
+			gpa_t addr, int len, const void *val)
+{
+	unsigned long flags;
+	struct loongson_kvm_ipi *ipi;
+	struct ipi_io_device *ipi_device;
+
+	ipi_device = container_of(dev, struct ipi_io_device, device);
+	ipi = ipi_device->ipi;
+
+	spin_lock_irqsave(&ipi->lock, flags);
+	loongson_vipi_write(ipi, addr, len, val);
+	spin_unlock_irqrestore(&ipi->lock, flags);
+
+	return 0;
+}
+
+static const struct kvm_io_device_ops kvm_ipi_ops = {
+	.read     = kvm_ipi_read,
+	.write    = kvm_ipi_write,
+};
+
+void kvm_init_loongson_ipi(struct kvm *kvm)
+{
+	int i;
+	unsigned long addr;
+	struct loongson_kvm_ipi *s;
+	struct kvm_io_device *device;
+
+	s = &kvm->arch.ipi;
+	s->kvm = kvm;
+	spin_lock_init(&s->lock);
+
+	/*
+	 * Initialize IPI device
+	 */
+	for (i = 0; i < 4; i++) {
+		device = &s->dev_ipi[i].device;
+		kvm_iodevice_init(device, &kvm_ipi_ops);
+		addr = (((unsigned long)i) << 44) + IPI_BASE;
+		mutex_lock(&kvm->slots_lock);
+		kvm_io_bus_register_dev(kvm, KVM_MMIO_BUS, addr, 0x400, device);
+		mutex_unlock(&kvm->slots_lock);
+		s->dev_ipi[i].ipi = s;
+		s->dev_ipi[i].node_id = i;
+	}
+}
diff --git a/arch/mips/kvm/mips.c b/arch/mips/kvm/mips.c
new file mode 100644
index 000000000..a4f4407b0
--- /dev/null
+++ b/arch/mips/kvm/mips.c
@@ -0,0 +1,1672 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * KVM/MIPS: MIPS specific KVM APIs
+ *
+ * Copyright (C) 2012  MIPS Technologies, Inc.  All rights reserved.
+ * Authors: Sanjay Lal <sanjayl@kymasys.com>
+ */
+
+#include <linux/bitops.h>
+#include <linux/errno.h>
+#include <linux/err.h>
+#include <linux/kdebug.h>
+#include <linux/module.h>
+#include <linux/uaccess.h>
+#include <linux/vmalloc.h>
+#include <linux/sched/signal.h>
+#include <linux/fs.h>
+#include <linux/memblock.h>
+#include <linux/pgtable.h>
+
+#include <asm/fpu.h>
+#include <asm/page.h>
+#include <asm/cacheflush.h>
+#include <asm/mmu_context.h>
+#include <asm/pgalloc.h>
+
+#include <linux/kvm_host.h>
+
+#include "interrupt.h"
+
+#define CREATE_TRACE_POINTS
+#include "trace.h"
+
+#ifndef VECTORSPACING
+#define VECTORSPACING 0x100	/* for EI/VI mode */
+#endif
+
+const struct _kvm_stats_desc kvm_vm_stats_desc[] = {
+	KVM_GENERIC_VM_STATS()
+};
+
+const struct kvm_stats_header kvm_vm_stats_header = {
+	.name_size = KVM_STATS_NAME_SIZE,
+	.num_desc = ARRAY_SIZE(kvm_vm_stats_desc),
+	.id_offset = sizeof(struct kvm_stats_header),
+	.desc_offset = sizeof(struct kvm_stats_header) + KVM_STATS_NAME_SIZE,
+	.data_offset = sizeof(struct kvm_stats_header) + KVM_STATS_NAME_SIZE +
+		       sizeof(kvm_vm_stats_desc),
+};
+
+const struct _kvm_stats_desc kvm_vcpu_stats_desc[] = {
+	KVM_GENERIC_VCPU_STATS(),
+	STATS_DESC_COUNTER(VCPU, wait_exits),
+	STATS_DESC_COUNTER(VCPU, cache_exits),
+	STATS_DESC_COUNTER(VCPU, signal_exits),
+	STATS_DESC_COUNTER(VCPU, int_exits),
+	STATS_DESC_COUNTER(VCPU, cop_unusable_exits),
+	STATS_DESC_COUNTER(VCPU, tlbmod_exits),
+	STATS_DESC_COUNTER(VCPU, tlbmiss_ld_exits),
+	STATS_DESC_COUNTER(VCPU, tlbmiss_st_exits),
+	STATS_DESC_COUNTER(VCPU, addrerr_st_exits),
+	STATS_DESC_COUNTER(VCPU, addrerr_ld_exits),
+	STATS_DESC_COUNTER(VCPU, syscall_exits),
+	STATS_DESC_COUNTER(VCPU, resvd_inst_exits),
+	STATS_DESC_COUNTER(VCPU, break_inst_exits),
+	STATS_DESC_COUNTER(VCPU, trap_inst_exits),
+	STATS_DESC_COUNTER(VCPU, msa_fpe_exits),
+	STATS_DESC_COUNTER(VCPU, fpe_exits),
+	STATS_DESC_COUNTER(VCPU, msa_disabled_exits),
+	STATS_DESC_COUNTER(VCPU, flush_dcache_exits),
+	STATS_DESC_COUNTER(VCPU, vz_gpsi_exits),
+	STATS_DESC_COUNTER(VCPU, vz_gsfc_exits),
+	STATS_DESC_COUNTER(VCPU, vz_hc_exits),
+	STATS_DESC_COUNTER(VCPU, vz_grr_exits),
+	STATS_DESC_COUNTER(VCPU, vz_gva_exits),
+	STATS_DESC_COUNTER(VCPU, vz_ghfc_exits),
+	STATS_DESC_COUNTER(VCPU, vz_gpa_exits),
+	STATS_DESC_COUNTER(VCPU, vz_resvd_exits),
+#ifdef CONFIG_CPU_LOONGSON64
+	STATS_DESC_COUNTER(VCPU, vz_cpucfg_exits),
+#endif
+};
+
+const struct kvm_stats_header kvm_vcpu_stats_header = {
+	.name_size = KVM_STATS_NAME_SIZE,
+	.num_desc = ARRAY_SIZE(kvm_vcpu_stats_desc),
+	.id_offset = sizeof(struct kvm_stats_header),
+	.desc_offset = sizeof(struct kvm_stats_header) + KVM_STATS_NAME_SIZE,
+	.data_offset = sizeof(struct kvm_stats_header) + KVM_STATS_NAME_SIZE +
+		       sizeof(kvm_vcpu_stats_desc),
+};
+
+bool kvm_trace_guest_mode_change;
+
+int kvm_guest_mode_change_trace_reg(void)
+{
+	kvm_trace_guest_mode_change = true;
+	return 0;
+}
+
+void kvm_guest_mode_change_trace_unreg(void)
+{
+	kvm_trace_guest_mode_change = false;
+}
+
+/*
+ * XXXKYMA: We are simulatoring a processor that has the WII bit set in
+ * Config7, so we are "runnable" if interrupts are pending
+ */
+int kvm_arch_vcpu_runnable(struct kvm_vcpu *vcpu)
+{
+	return !!(vcpu->arch.pending_exceptions);
+}
+
+bool kvm_arch_vcpu_in_kernel(struct kvm_vcpu *vcpu)
+{
+	return false;
+}
+
+int kvm_arch_vcpu_should_kick(struct kvm_vcpu *vcpu)
+{
+	return 1;
+}
+
+int kvm_arch_hardware_enable(void)
+{
+	return kvm_mips_callbacks->hardware_enable();
+}
+
+void kvm_arch_hardware_disable(void)
+{
+	kvm_mips_callbacks->hardware_disable();
+}
+
+int kvm_arch_hardware_setup(void *opaque)
+{
+	return 0;
+}
+
+int kvm_arch_check_processor_compat(void *opaque)
+{
+	return 0;
+}
+
+extern void kvm_init_loongson_ipi(struct kvm *kvm);
+
+int kvm_arch_init_vm(struct kvm *kvm, unsigned long type)
+{
+	switch (type) {
+	case KVM_VM_MIPS_AUTO:
+		break;
+	case KVM_VM_MIPS_VZ:
+		break;
+	default:
+		/* Unsupported KVM type */
+		return -EINVAL;
+	}
+
+	/* Allocate page table to map GPA -> RPA */
+	kvm->arch.gpa_mm.pgd = kvm_pgd_alloc();
+	if (!kvm->arch.gpa_mm.pgd)
+		return -ENOMEM;
+
+#ifdef CONFIG_CPU_LOONGSON64
+	kvm_init_loongson_ipi(kvm);
+#endif
+
+	return 0;
+}
+
+static void kvm_mips_free_gpa_pt(struct kvm *kvm)
+{
+	/* It should always be safe to remove after flushing the whole range */
+	WARN_ON(!kvm_mips_flush_gpa_pt(kvm, 0, ~0));
+	pgd_free(NULL, kvm->arch.gpa_mm.pgd);
+}
+
+void kvm_arch_destroy_vm(struct kvm *kvm)
+{
+	kvm_destroy_vcpus(kvm);
+	kvm_mips_free_gpa_pt(kvm);
+}
+
+long kvm_arch_dev_ioctl(struct file *filp, unsigned int ioctl,
+			unsigned long arg)
+{
+	return -ENOIOCTLCMD;
+}
+
+void kvm_arch_flush_shadow_all(struct kvm *kvm)
+{
+	/* Flush whole GPA */
+	kvm_mips_flush_gpa_pt(kvm, 0, ~0);
+	kvm_flush_remote_tlbs(kvm);
+}
+
+void kvm_arch_flush_shadow_memslot(struct kvm *kvm,
+				   struct kvm_memory_slot *slot)
+{
+	/*
+	 * The slot has been made invalid (ready for moving or deletion), so we
+	 * need to ensure that it can no longer be accessed by any guest VCPUs.
+	 */
+
+	spin_lock(&kvm->mmu_lock);
+	/* Flush slot from GPA */
+	kvm_mips_flush_gpa_pt(kvm, slot->base_gfn,
+			      slot->base_gfn + slot->npages - 1);
+	kvm_arch_flush_remote_tlbs_memslot(kvm, slot);
+	spin_unlock(&kvm->mmu_lock);
+}
+
+int kvm_arch_prepare_memory_region(struct kvm *kvm,
+				   const struct kvm_memory_slot *old,
+				   struct kvm_memory_slot *new,
+				   enum kvm_mr_change change)
+{
+	return 0;
+}
+
+void kvm_arch_commit_memory_region(struct kvm *kvm,
+				   struct kvm_memory_slot *old,
+				   const struct kvm_memory_slot *new,
+				   enum kvm_mr_change change)
+{
+	int needs_flush;
+
+	/*
+	 * If dirty page logging is enabled, write protect all pages in the slot
+	 * ready for dirty logging.
+	 *
+	 * There is no need to do this in any of the following cases:
+	 * CREATE:	No dirty mappings will already exist.
+	 * MOVE/DELETE:	The old mappings will already have been cleaned up by
+	 *		kvm_arch_flush_shadow_memslot()
+	 */
+	if (change == KVM_MR_FLAGS_ONLY &&
+	    (!(old->flags & KVM_MEM_LOG_DIRTY_PAGES) &&
+	     new->flags & KVM_MEM_LOG_DIRTY_PAGES)) {
+		spin_lock(&kvm->mmu_lock);
+		/* Write protect GPA page table entries */
+		needs_flush = kvm_mips_mkclean_gpa_pt(kvm, new->base_gfn,
+					new->base_gfn + new->npages - 1);
+		if (needs_flush)
+			kvm_arch_flush_remote_tlbs_memslot(kvm, new);
+		spin_unlock(&kvm->mmu_lock);
+	}
+}
+
+static inline void dump_handler(const char *symbol, void *start, void *end)
+{
+	u32 *p;
+
+	pr_debug("LEAF(%s)\n", symbol);
+
+	pr_debug("\t.set push\n");
+	pr_debug("\t.set noreorder\n");
+
+	for (p = start; p < (u32 *)end; ++p)
+		pr_debug("\t.word\t0x%08x\t\t# %p\n", *p, p);
+
+	pr_debug("\t.set\tpop\n");
+
+	pr_debug("\tEND(%s)\n", symbol);
+}
+
+/* low level hrtimer wake routine */
+static enum hrtimer_restart kvm_mips_comparecount_wakeup(struct hrtimer *timer)
+{
+	struct kvm_vcpu *vcpu;
+
+	vcpu = container_of(timer, struct kvm_vcpu, arch.comparecount_timer);
+
+	kvm_mips_callbacks->queue_timer_int(vcpu);
+
+	vcpu->arch.wait = 0;
+	rcuwait_wake_up(&vcpu->wait);
+
+	return kvm_mips_count_timeout(vcpu);
+}
+
+int kvm_arch_vcpu_precreate(struct kvm *kvm, unsigned int id)
+{
+	return 0;
+}
+
+int kvm_arch_vcpu_create(struct kvm_vcpu *vcpu)
+{
+	int err, size;
+	void *gebase, *p, *handler, *refill_start, *refill_end;
+	int i;
+
+	kvm_debug("kvm @ %p: create cpu %d at %p\n",
+		  vcpu->kvm, vcpu->vcpu_id, vcpu);
+
+	err = kvm_mips_callbacks->vcpu_init(vcpu);
+	if (err)
+		return err;
+
+	hrtimer_init(&vcpu->arch.comparecount_timer, CLOCK_MONOTONIC,
+		     HRTIMER_MODE_REL);
+	vcpu->arch.comparecount_timer.function = kvm_mips_comparecount_wakeup;
+
+	/*
+	 * Allocate space for host mode exception handlers that handle
+	 * guest mode exits
+	 */
+	if (cpu_has_veic || cpu_has_vint)
+		size = 0x200 + VECTORSPACING * 64;
+	else
+		size = 0x4000;
+
+	gebase = kzalloc(ALIGN(size, PAGE_SIZE), GFP_KERNEL);
+
+	if (!gebase) {
+		err = -ENOMEM;
+		goto out_uninit_vcpu;
+	}
+	kvm_debug("Allocated %d bytes for KVM Exception Handlers @ %p\n",
+		  ALIGN(size, PAGE_SIZE), gebase);
+
+	/*
+	 * Check new ebase actually fits in CP0_EBase. The lack of a write gate
+	 * limits us to the low 512MB of physical address space. If the memory
+	 * we allocate is out of range, just give up now.
+	 */
+	if (!cpu_has_ebase_wg && virt_to_phys(gebase) >= 0x20000000) {
+		kvm_err("CP0_EBase.WG required for guest exception base %pK\n",
+			gebase);
+		err = -ENOMEM;
+		goto out_free_gebase;
+	}
+
+	/* Save new ebase */
+	vcpu->arch.guest_ebase = gebase;
+
+	/* Build guest exception vectors dynamically in unmapped memory */
+	handler = gebase + 0x2000;
+
+	/* TLB refill (or XTLB refill on 64-bit VZ where KX=1) */
+	refill_start = gebase;
+	if (IS_ENABLED(CONFIG_64BIT))
+		refill_start += 0x080;
+	refill_end = kvm_mips_build_tlb_refill_exception(refill_start, handler);
+
+	/* General Exception Entry point */
+	kvm_mips_build_exception(gebase + 0x180, handler);
+
+	/* For vectored interrupts poke the exception code @ all offsets 0-7 */
+	for (i = 0; i < 8; i++) {
+		kvm_debug("L1 Vectored handler @ %p\n",
+			  gebase + 0x200 + (i * VECTORSPACING));
+		kvm_mips_build_exception(gebase + 0x200 + i * VECTORSPACING,
+					 handler);
+	}
+
+	/* General exit handler */
+	p = handler;
+	p = kvm_mips_build_exit(p);
+
+	/* Guest entry routine */
+	vcpu->arch.vcpu_run = p;
+	p = kvm_mips_build_vcpu_run(p);
+
+	/* Dump the generated code */
+	pr_debug("#include <asm/asm.h>\n");
+	pr_debug("#include <asm/regdef.h>\n");
+	pr_debug("\n");
+	dump_handler("kvm_vcpu_run", vcpu->arch.vcpu_run, p);
+	dump_handler("kvm_tlb_refill", refill_start, refill_end);
+	dump_handler("kvm_gen_exc", gebase + 0x180, gebase + 0x200);
+	dump_handler("kvm_exit", gebase + 0x2000, vcpu->arch.vcpu_run);
+
+	/* Invalidate the icache for these ranges */
+	flush_icache_range((unsigned long)gebase,
+			   (unsigned long)gebase + ALIGN(size, PAGE_SIZE));
+
+	/* Init */
+	vcpu->arch.last_sched_cpu = -1;
+	vcpu->arch.last_exec_cpu = -1;
+
+	/* Initial guest state */
+	err = kvm_mips_callbacks->vcpu_setup(vcpu);
+	if (err)
+		goto out_free_gebase;
+
+	return 0;
+
+out_free_gebase:
+	kfree(gebase);
+out_uninit_vcpu:
+	kvm_mips_callbacks->vcpu_uninit(vcpu);
+	return err;
+}
+
+void kvm_arch_vcpu_destroy(struct kvm_vcpu *vcpu)
+{
+	hrtimer_cancel(&vcpu->arch.comparecount_timer);
+
+	kvm_mips_dump_stats(vcpu);
+
+	kvm_mmu_free_memory_caches(vcpu);
+	kfree(vcpu->arch.guest_ebase);
+
+	kvm_mips_callbacks->vcpu_uninit(vcpu);
+}
+
+int kvm_arch_vcpu_ioctl_set_guest_debug(struct kvm_vcpu *vcpu,
+					struct kvm_guest_debug *dbg)
+{
+	return -ENOIOCTLCMD;
+}
+
+/*
+ * Actually run the vCPU, entering an RCU extended quiescent state (EQS) while
+ * the vCPU is running.
+ *
+ * This must be noinstr as instrumentation may make use of RCU, and this is not
+ * safe during the EQS.
+ */
+static int noinstr kvm_mips_vcpu_enter_exit(struct kvm_vcpu *vcpu)
+{
+	int ret;
+
+	guest_state_enter_irqoff();
+	ret = kvm_mips_callbacks->vcpu_run(vcpu);
+	guest_state_exit_irqoff();
+
+	return ret;
+}
+
+int kvm_arch_vcpu_ioctl_run(struct kvm_vcpu *vcpu)
+{
+	int r = -EINTR;
+
+	vcpu_load(vcpu);
+
+	kvm_sigset_activate(vcpu);
+
+	if (vcpu->mmio_needed) {
+		if (!vcpu->mmio_is_write)
+			kvm_mips_complete_mmio_load(vcpu);
+		vcpu->mmio_needed = 0;
+	}
+
+	if (vcpu->run->immediate_exit)
+		goto out;
+
+	lose_fpu(1);
+
+	local_irq_disable();
+	guest_timing_enter_irqoff();
+	trace_kvm_enter(vcpu);
+
+	/*
+	 * Make sure the read of VCPU requests in vcpu_run() callback is not
+	 * reordered ahead of the write to vcpu->mode, or we could miss a TLB
+	 * flush request while the requester sees the VCPU as outside of guest
+	 * mode and not needing an IPI.
+	 */
+	smp_store_mb(vcpu->mode, IN_GUEST_MODE);
+
+	r = kvm_mips_vcpu_enter_exit(vcpu);
+
+	/*
+	 * We must ensure that any pending interrupts are taken before
+	 * we exit guest timing so that timer ticks are accounted as
+	 * guest time. Transiently unmask interrupts so that any
+	 * pending interrupts are taken.
+	 *
+	 * TODO: is there a barrier which ensures that pending interrupts are
+	 * recognised? Currently this just hopes that the CPU takes any pending
+	 * interrupts between the enable and disable.
+	 */
+	local_irq_enable();
+	local_irq_disable();
+
+	trace_kvm_out(vcpu);
+	guest_timing_exit_irqoff();
+	local_irq_enable();
+
+out:
+	kvm_sigset_deactivate(vcpu);
+
+	vcpu_put(vcpu);
+	return r;
+}
+
+int kvm_vcpu_ioctl_interrupt(struct kvm_vcpu *vcpu,
+			     struct kvm_mips_interrupt *irq)
+{
+	int intr = (int)irq->irq;
+	struct kvm_vcpu *dvcpu = NULL;
+
+	if (intr == kvm_priority_to_irq[MIPS_EXC_INT_IPI_1] ||
+	    intr == kvm_priority_to_irq[MIPS_EXC_INT_IPI_2] ||
+	    intr == (-kvm_priority_to_irq[MIPS_EXC_INT_IPI_1]) ||
+	    intr == (-kvm_priority_to_irq[MIPS_EXC_INT_IPI_2]))
+		kvm_debug("%s: CPU: %d, INTR: %d\n", __func__, irq->cpu,
+			  (int)intr);
+
+	if (irq->cpu == -1)
+		dvcpu = vcpu;
+	else
+		dvcpu = kvm_get_vcpu(vcpu->kvm, irq->cpu);
+
+	if (intr == 2 || intr == 3 || intr == 4 || intr == 6) {
+		kvm_mips_callbacks->queue_io_int(dvcpu, irq);
+
+	} else if (intr == -2 || intr == -3 || intr == -4 || intr == -6) {
+		kvm_mips_callbacks->dequeue_io_int(dvcpu, irq);
+	} else {
+		kvm_err("%s: invalid interrupt ioctl (%d:%d)\n", __func__,
+			irq->cpu, irq->irq);
+		return -EINVAL;
+	}
+
+	dvcpu->arch.wait = 0;
+
+	rcuwait_wake_up(&dvcpu->wait);
+
+	return 0;
+}
+
+int kvm_arch_vcpu_ioctl_get_mpstate(struct kvm_vcpu *vcpu,
+				    struct kvm_mp_state *mp_state)
+{
+	return -ENOIOCTLCMD;
+}
+
+int kvm_arch_vcpu_ioctl_set_mpstate(struct kvm_vcpu *vcpu,
+				    struct kvm_mp_state *mp_state)
+{
+	return -ENOIOCTLCMD;
+}
+
+static u64 kvm_mips_get_one_regs[] = {
+	KVM_REG_MIPS_R0,
+	KVM_REG_MIPS_R1,
+	KVM_REG_MIPS_R2,
+	KVM_REG_MIPS_R3,
+	KVM_REG_MIPS_R4,
+	KVM_REG_MIPS_R5,
+	KVM_REG_MIPS_R6,
+	KVM_REG_MIPS_R7,
+	KVM_REG_MIPS_R8,
+	KVM_REG_MIPS_R9,
+	KVM_REG_MIPS_R10,
+	KVM_REG_MIPS_R11,
+	KVM_REG_MIPS_R12,
+	KVM_REG_MIPS_R13,
+	KVM_REG_MIPS_R14,
+	KVM_REG_MIPS_R15,
+	KVM_REG_MIPS_R16,
+	KVM_REG_MIPS_R17,
+	KVM_REG_MIPS_R18,
+	KVM_REG_MIPS_R19,
+	KVM_REG_MIPS_R20,
+	KVM_REG_MIPS_R21,
+	KVM_REG_MIPS_R22,
+	KVM_REG_MIPS_R23,
+	KVM_REG_MIPS_R24,
+	KVM_REG_MIPS_R25,
+	KVM_REG_MIPS_R26,
+	KVM_REG_MIPS_R27,
+	KVM_REG_MIPS_R28,
+	KVM_REG_MIPS_R29,
+	KVM_REG_MIPS_R30,
+	KVM_REG_MIPS_R31,
+
+#ifndef CONFIG_CPU_MIPSR6
+	KVM_REG_MIPS_HI,
+	KVM_REG_MIPS_LO,
+#endif
+	KVM_REG_MIPS_PC,
+};
+
+static u64 kvm_mips_get_one_regs_fpu[] = {
+	KVM_REG_MIPS_FCR_IR,
+	KVM_REG_MIPS_FCR_CSR,
+};
+
+static u64 kvm_mips_get_one_regs_msa[] = {
+	KVM_REG_MIPS_MSA_IR,
+	KVM_REG_MIPS_MSA_CSR,
+};
+
+static unsigned long kvm_mips_num_regs(struct kvm_vcpu *vcpu)
+{
+	unsigned long ret;
+
+	ret = ARRAY_SIZE(kvm_mips_get_one_regs);
+	if (kvm_mips_guest_can_have_fpu(&vcpu->arch)) {
+		ret += ARRAY_SIZE(kvm_mips_get_one_regs_fpu) + 48;
+		/* odd doubles */
+		if (boot_cpu_data.fpu_id & MIPS_FPIR_F64)
+			ret += 16;
+	}
+	if (kvm_mips_guest_can_have_msa(&vcpu->arch))
+		ret += ARRAY_SIZE(kvm_mips_get_one_regs_msa) + 32;
+	ret += kvm_mips_callbacks->num_regs(vcpu);
+
+	return ret;
+}
+
+static int kvm_mips_copy_reg_indices(struct kvm_vcpu *vcpu, u64 __user *indices)
+{
+	u64 index;
+	unsigned int i;
+
+	if (copy_to_user(indices, kvm_mips_get_one_regs,
+			 sizeof(kvm_mips_get_one_regs)))
+		return -EFAULT;
+	indices += ARRAY_SIZE(kvm_mips_get_one_regs);
+
+	if (kvm_mips_guest_can_have_fpu(&vcpu->arch)) {
+		if (copy_to_user(indices, kvm_mips_get_one_regs_fpu,
+				 sizeof(kvm_mips_get_one_regs_fpu)))
+			return -EFAULT;
+		indices += ARRAY_SIZE(kvm_mips_get_one_regs_fpu);
+
+		for (i = 0; i < 32; ++i) {
+			index = KVM_REG_MIPS_FPR_32(i);
+			if (copy_to_user(indices, &index, sizeof(index)))
+				return -EFAULT;
+			++indices;
+
+			/* skip odd doubles if no F64 */
+			if (i & 1 && !(boot_cpu_data.fpu_id & MIPS_FPIR_F64))
+				continue;
+
+			index = KVM_REG_MIPS_FPR_64(i);
+			if (copy_to_user(indices, &index, sizeof(index)))
+				return -EFAULT;
+			++indices;
+		}
+	}
+
+	if (kvm_mips_guest_can_have_msa(&vcpu->arch)) {
+		if (copy_to_user(indices, kvm_mips_get_one_regs_msa,
+				 sizeof(kvm_mips_get_one_regs_msa)))
+			return -EFAULT;
+		indices += ARRAY_SIZE(kvm_mips_get_one_regs_msa);
+
+		for (i = 0; i < 32; ++i) {
+			index = KVM_REG_MIPS_VEC_128(i);
+			if (copy_to_user(indices, &index, sizeof(index)))
+				return -EFAULT;
+			++indices;
+		}
+	}
+
+	return kvm_mips_callbacks->copy_reg_indices(vcpu, indices);
+}
+
+static int kvm_mips_get_reg(struct kvm_vcpu *vcpu,
+			    const struct kvm_one_reg *reg)
+{
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
+	struct mips_fpu_struct *fpu = &vcpu->arch.fpu;
+	int ret;
+	s64 v;
+	s64 vs[2];
+	unsigned int idx;
+
+	switch (reg->id) {
+	/* General purpose registers */
+	case KVM_REG_MIPS_R0 ... KVM_REG_MIPS_R31:
+		v = (long)vcpu->arch.gprs[reg->id - KVM_REG_MIPS_R0];
+		break;
+#ifndef CONFIG_CPU_MIPSR6
+	case KVM_REG_MIPS_HI:
+		v = (long)vcpu->arch.hi;
+		break;
+	case KVM_REG_MIPS_LO:
+		v = (long)vcpu->arch.lo;
+		break;
+#endif
+	case KVM_REG_MIPS_PC:
+		v = (long)vcpu->arch.pc;
+		break;
+
+	/* Floating point registers */
+	case KVM_REG_MIPS_FPR_32(0) ... KVM_REG_MIPS_FPR_32(31):
+		if (!kvm_mips_guest_has_fpu(&vcpu->arch))
+			return -EINVAL;
+		idx = reg->id - KVM_REG_MIPS_FPR_32(0);
+		/* Odd singles in top of even double when FR=0 */
+		if (kvm_read_c0_guest_status(cop0) & ST0_FR)
+			v = get_fpr32(&fpu->fpr[idx], 0);
+		else
+			v = get_fpr32(&fpu->fpr[idx & ~1], idx & 1);
+		break;
+	case KVM_REG_MIPS_FPR_64(0) ... KVM_REG_MIPS_FPR_64(31):
+		if (!kvm_mips_guest_has_fpu(&vcpu->arch))
+			return -EINVAL;
+		idx = reg->id - KVM_REG_MIPS_FPR_64(0);
+		/* Can't access odd doubles in FR=0 mode */
+		if (idx & 1 && !(kvm_read_c0_guest_status(cop0) & ST0_FR))
+			return -EINVAL;
+		v = get_fpr64(&fpu->fpr[idx], 0);
+		break;
+	case KVM_REG_MIPS_FCR_IR:
+		if (!kvm_mips_guest_has_fpu(&vcpu->arch))
+			return -EINVAL;
+		v = boot_cpu_data.fpu_id;
+		break;
+	case KVM_REG_MIPS_FCR_CSR:
+		if (!kvm_mips_guest_has_fpu(&vcpu->arch))
+			return -EINVAL;
+		v = fpu->fcr31;
+		break;
+
+	/* MIPS SIMD Architecture (MSA) registers */
+	case KVM_REG_MIPS_VEC_128(0) ... KVM_REG_MIPS_VEC_128(31):
+		if (!kvm_mips_guest_has_msa(&vcpu->arch))
+			return -EINVAL;
+		/* Can't access MSA registers in FR=0 mode */
+		if (!(kvm_read_c0_guest_status(cop0) & ST0_FR))
+			return -EINVAL;
+		idx = reg->id - KVM_REG_MIPS_VEC_128(0);
+#ifdef CONFIG_CPU_LITTLE_ENDIAN
+		/* least significant byte first */
+		vs[0] = get_fpr64(&fpu->fpr[idx], 0);
+		vs[1] = get_fpr64(&fpu->fpr[idx], 1);
+#else
+		/* most significant byte first */
+		vs[0] = get_fpr64(&fpu->fpr[idx], 1);
+		vs[1] = get_fpr64(&fpu->fpr[idx], 0);
+#endif
+		break;
+	case KVM_REG_MIPS_MSA_IR:
+		if (!kvm_mips_guest_has_msa(&vcpu->arch))
+			return -EINVAL;
+		v = boot_cpu_data.msa_id;
+		break;
+	case KVM_REG_MIPS_MSA_CSR:
+		if (!kvm_mips_guest_has_msa(&vcpu->arch))
+			return -EINVAL;
+		v = fpu->msacsr;
+		break;
+
+	/* registers to be handled specially */
+	default:
+		ret = kvm_mips_callbacks->get_one_reg(vcpu, reg, &v);
+		if (ret)
+			return ret;
+		break;
+	}
+	if ((reg->id & KVM_REG_SIZE_MASK) == KVM_REG_SIZE_U64) {
+		u64 __user *uaddr64 = (u64 __user *)(long)reg->addr;
+
+		return put_user(v, uaddr64);
+	} else if ((reg->id & KVM_REG_SIZE_MASK) == KVM_REG_SIZE_U32) {
+		u32 __user *uaddr32 = (u32 __user *)(long)reg->addr;
+		u32 v32 = (u32)v;
+
+		return put_user(v32, uaddr32);
+	} else if ((reg->id & KVM_REG_SIZE_MASK) == KVM_REG_SIZE_U128) {
+		void __user *uaddr = (void __user *)(long)reg->addr;
+
+		return copy_to_user(uaddr, vs, 16) ? -EFAULT : 0;
+	} else {
+		return -EINVAL;
+	}
+}
+
+static int kvm_mips_set_reg(struct kvm_vcpu *vcpu,
+			    const struct kvm_one_reg *reg)
+{
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
+	struct mips_fpu_struct *fpu = &vcpu->arch.fpu;
+	s64 v;
+	s64 vs[2];
+	unsigned int idx;
+
+	if ((reg->id & KVM_REG_SIZE_MASK) == KVM_REG_SIZE_U64) {
+		u64 __user *uaddr64 = (u64 __user *)(long)reg->addr;
+
+		if (get_user(v, uaddr64) != 0)
+			return -EFAULT;
+	} else if ((reg->id & KVM_REG_SIZE_MASK) == KVM_REG_SIZE_U32) {
+		u32 __user *uaddr32 = (u32 __user *)(long)reg->addr;
+		s32 v32;
+
+		if (get_user(v32, uaddr32) != 0)
+			return -EFAULT;
+		v = (s64)v32;
+	} else if ((reg->id & KVM_REG_SIZE_MASK) == KVM_REG_SIZE_U128) {
+		void __user *uaddr = (void __user *)(long)reg->addr;
+
+		return copy_from_user(vs, uaddr, 16) ? -EFAULT : 0;
+	} else {
+		return -EINVAL;
+	}
+
+	switch (reg->id) {
+	/* General purpose registers */
+	case KVM_REG_MIPS_R0:
+		/* Silently ignore requests to set $0 */
+		break;
+	case KVM_REG_MIPS_R1 ... KVM_REG_MIPS_R31:
+		vcpu->arch.gprs[reg->id - KVM_REG_MIPS_R0] = v;
+		break;
+#ifndef CONFIG_CPU_MIPSR6
+	case KVM_REG_MIPS_HI:
+		vcpu->arch.hi = v;
+		break;
+	case KVM_REG_MIPS_LO:
+		vcpu->arch.lo = v;
+		break;
+#endif
+	case KVM_REG_MIPS_PC:
+		vcpu->arch.pc = v;
+		break;
+
+	/* Floating point registers */
+	case KVM_REG_MIPS_FPR_32(0) ... KVM_REG_MIPS_FPR_32(31):
+		if (!kvm_mips_guest_has_fpu(&vcpu->arch))
+			return -EINVAL;
+		idx = reg->id - KVM_REG_MIPS_FPR_32(0);
+		/* Odd singles in top of even double when FR=0 */
+		if (kvm_read_c0_guest_status(cop0) & ST0_FR)
+			set_fpr32(&fpu->fpr[idx], 0, v);
+		else
+			set_fpr32(&fpu->fpr[idx & ~1], idx & 1, v);
+		break;
+	case KVM_REG_MIPS_FPR_64(0) ... KVM_REG_MIPS_FPR_64(31):
+		if (!kvm_mips_guest_has_fpu(&vcpu->arch))
+			return -EINVAL;
+		idx = reg->id - KVM_REG_MIPS_FPR_64(0);
+		/* Can't access odd doubles in FR=0 mode */
+		if (idx & 1 && !(kvm_read_c0_guest_status(cop0) & ST0_FR))
+			return -EINVAL;
+		set_fpr64(&fpu->fpr[idx], 0, v);
+		break;
+	case KVM_REG_MIPS_FCR_IR:
+		if (!kvm_mips_guest_has_fpu(&vcpu->arch))
+			return -EINVAL;
+		/* Read-only */
+		break;
+	case KVM_REG_MIPS_FCR_CSR:
+		if (!kvm_mips_guest_has_fpu(&vcpu->arch))
+			return -EINVAL;
+		fpu->fcr31 = v;
+		break;
+
+	/* MIPS SIMD Architecture (MSA) registers */
+	case KVM_REG_MIPS_VEC_128(0) ... KVM_REG_MIPS_VEC_128(31):
+		if (!kvm_mips_guest_has_msa(&vcpu->arch))
+			return -EINVAL;
+		idx = reg->id - KVM_REG_MIPS_VEC_128(0);
+#ifdef CONFIG_CPU_LITTLE_ENDIAN
+		/* least significant byte first */
+		set_fpr64(&fpu->fpr[idx], 0, vs[0]);
+		set_fpr64(&fpu->fpr[idx], 1, vs[1]);
+#else
+		/* most significant byte first */
+		set_fpr64(&fpu->fpr[idx], 1, vs[0]);
+		set_fpr64(&fpu->fpr[idx], 0, vs[1]);
+#endif
+		break;
+	case KVM_REG_MIPS_MSA_IR:
+		if (!kvm_mips_guest_has_msa(&vcpu->arch))
+			return -EINVAL;
+		/* Read-only */
+		break;
+	case KVM_REG_MIPS_MSA_CSR:
+		if (!kvm_mips_guest_has_msa(&vcpu->arch))
+			return -EINVAL;
+		fpu->msacsr = v;
+		break;
+
+	/* registers to be handled specially */
+	default:
+		return kvm_mips_callbacks->set_one_reg(vcpu, reg, v);
+	}
+	return 0;
+}
+
+static int kvm_vcpu_ioctl_enable_cap(struct kvm_vcpu *vcpu,
+				     struct kvm_enable_cap *cap)
+{
+	int r = 0;
+
+	if (!kvm_vm_ioctl_check_extension(vcpu->kvm, cap->cap))
+		return -EINVAL;
+	if (cap->flags)
+		return -EINVAL;
+	if (cap->args[0])
+		return -EINVAL;
+
+	switch (cap->cap) {
+	case KVM_CAP_MIPS_FPU:
+		vcpu->arch.fpu_enabled = true;
+		break;
+	case KVM_CAP_MIPS_MSA:
+		vcpu->arch.msa_enabled = true;
+		break;
+	default:
+		r = -EINVAL;
+		break;
+	}
+
+	return r;
+}
+
+long kvm_arch_vcpu_async_ioctl(struct file *filp, unsigned int ioctl,
+			       unsigned long arg)
+{
+	struct kvm_vcpu *vcpu = filp->private_data;
+	void __user *argp = (void __user *)arg;
+
+	if (ioctl == KVM_INTERRUPT) {
+		struct kvm_mips_interrupt irq;
+
+		if (copy_from_user(&irq, argp, sizeof(irq)))
+			return -EFAULT;
+		kvm_debug("[%d] %s: irq: %d\n", vcpu->vcpu_id, __func__,
+			  irq.irq);
+
+		return kvm_vcpu_ioctl_interrupt(vcpu, &irq);
+	}
+
+	return -ENOIOCTLCMD;
+}
+
+long kvm_arch_vcpu_ioctl(struct file *filp, unsigned int ioctl,
+			 unsigned long arg)
+{
+	struct kvm_vcpu *vcpu = filp->private_data;
+	void __user *argp = (void __user *)arg;
+	long r;
+
+	vcpu_load(vcpu);
+
+	switch (ioctl) {
+	case KVM_SET_ONE_REG:
+	case KVM_GET_ONE_REG: {
+		struct kvm_one_reg reg;
+
+		r = -EFAULT;
+		if (copy_from_user(&reg, argp, sizeof(reg)))
+			break;
+		if (ioctl == KVM_SET_ONE_REG)
+			r = kvm_mips_set_reg(vcpu, &reg);
+		else
+			r = kvm_mips_get_reg(vcpu, &reg);
+		break;
+	}
+	case KVM_GET_REG_LIST: {
+		struct kvm_reg_list __user *user_list = argp;
+		struct kvm_reg_list reg_list;
+		unsigned n;
+
+		r = -EFAULT;
+		if (copy_from_user(&reg_list, user_list, sizeof(reg_list)))
+			break;
+		n = reg_list.n;
+		reg_list.n = kvm_mips_num_regs(vcpu);
+		if (copy_to_user(user_list, &reg_list, sizeof(reg_list)))
+			break;
+		r = -E2BIG;
+		if (n < reg_list.n)
+			break;
+		r = kvm_mips_copy_reg_indices(vcpu, user_list->reg);
+		break;
+	}
+	case KVM_ENABLE_CAP: {
+		struct kvm_enable_cap cap;
+
+		r = -EFAULT;
+		if (copy_from_user(&cap, argp, sizeof(cap)))
+			break;
+		r = kvm_vcpu_ioctl_enable_cap(vcpu, &cap);
+		break;
+	}
+	default:
+		r = -ENOIOCTLCMD;
+	}
+
+	vcpu_put(vcpu);
+	return r;
+}
+
+void kvm_arch_sync_dirty_log(struct kvm *kvm, struct kvm_memory_slot *memslot)
+{
+
+}
+
+int kvm_arch_flush_remote_tlb(struct kvm *kvm)
+{
+	kvm_mips_callbacks->prepare_flush_shadow(kvm);
+	return 1;
+}
+
+void kvm_arch_flush_remote_tlbs_memslot(struct kvm *kvm,
+					const struct kvm_memory_slot *memslot)
+{
+	kvm_flush_remote_tlbs(kvm);
+}
+
+long kvm_arch_vm_ioctl(struct file *filp, unsigned int ioctl, unsigned long arg)
+{
+	long r;
+
+	switch (ioctl) {
+	default:
+		r = -ENOIOCTLCMD;
+	}
+
+	return r;
+}
+
+int kvm_arch_init(void *opaque)
+{
+	if (kvm_mips_callbacks) {
+		kvm_err("kvm: module already exists\n");
+		return -EEXIST;
+	}
+
+	return kvm_mips_emulation_init(&kvm_mips_callbacks);
+}
+
+void kvm_arch_exit(void)
+{
+	kvm_mips_callbacks = NULL;
+}
+
+int kvm_arch_vcpu_ioctl_get_sregs(struct kvm_vcpu *vcpu,
+				  struct kvm_sregs *sregs)
+{
+	return -ENOIOCTLCMD;
+}
+
+int kvm_arch_vcpu_ioctl_set_sregs(struct kvm_vcpu *vcpu,
+				  struct kvm_sregs *sregs)
+{
+	return -ENOIOCTLCMD;
+}
+
+void kvm_arch_vcpu_postcreate(struct kvm_vcpu *vcpu)
+{
+}
+
+int kvm_arch_vcpu_ioctl_get_fpu(struct kvm_vcpu *vcpu, struct kvm_fpu *fpu)
+{
+	return -ENOIOCTLCMD;
+}
+
+int kvm_arch_vcpu_ioctl_set_fpu(struct kvm_vcpu *vcpu, struct kvm_fpu *fpu)
+{
+	return -ENOIOCTLCMD;
+}
+
+vm_fault_t kvm_arch_vcpu_fault(struct kvm_vcpu *vcpu, struct vm_fault *vmf)
+{
+	return VM_FAULT_SIGBUS;
+}
+
+int kvm_vm_ioctl_check_extension(struct kvm *kvm, long ext)
+{
+	int r;
+
+	switch (ext) {
+	case KVM_CAP_ONE_REG:
+	case KVM_CAP_ENABLE_CAP:
+	case KVM_CAP_READONLY_MEM:
+	case KVM_CAP_SYNC_MMU:
+	case KVM_CAP_IMMEDIATE_EXIT:
+		r = 1;
+		break;
+	case KVM_CAP_NR_VCPUS:
+		r = min_t(unsigned int, num_online_cpus(), KVM_MAX_VCPUS);
+		break;
+	case KVM_CAP_MAX_VCPUS:
+		r = KVM_MAX_VCPUS;
+		break;
+	case KVM_CAP_MAX_VCPU_ID:
+		r = KVM_MAX_VCPU_IDS;
+		break;
+	case KVM_CAP_MIPS_FPU:
+		/* We don't handle systems with inconsistent cpu_has_fpu */
+		r = !!raw_cpu_has_fpu;
+		break;
+	case KVM_CAP_MIPS_MSA:
+		/*
+		 * We don't support MSA vector partitioning yet:
+		 * 1) It would require explicit support which can't be tested
+		 *    yet due to lack of support in current hardware.
+		 * 2) It extends the state that would need to be saved/restored
+		 *    by e.g. QEMU for migration.
+		 *
+		 * When vector partitioning hardware becomes available, support
+		 * could be added by requiring a flag when enabling
+		 * KVM_CAP_MIPS_MSA capability to indicate that userland knows
+		 * to save/restore the appropriate extra state.
+		 */
+		r = cpu_has_msa && !(boot_cpu_data.msa_id & MSA_IR_WRPF);
+		break;
+	default:
+		r = kvm_mips_callbacks->check_extension(kvm, ext);
+		break;
+	}
+	return r;
+}
+
+int kvm_cpu_has_pending_timer(struct kvm_vcpu *vcpu)
+{
+	return kvm_mips_pending_timer(vcpu) ||
+		kvm_read_c0_guest_cause(&vcpu->arch.cop0) & C_TI;
+}
+
+int kvm_arch_vcpu_dump_regs(struct kvm_vcpu *vcpu)
+{
+	int i;
+	struct mips_coproc *cop0;
+
+	if (!vcpu)
+		return -1;
+
+	kvm_debug("VCPU Register Dump:\n");
+	kvm_debug("\tpc = 0x%08lx\n", vcpu->arch.pc);
+	kvm_debug("\texceptions: %08lx\n", vcpu->arch.pending_exceptions);
+
+	for (i = 0; i < 32; i += 4) {
+		kvm_debug("\tgpr%02d: %08lx %08lx %08lx %08lx\n", i,
+		       vcpu->arch.gprs[i],
+		       vcpu->arch.gprs[i + 1],
+		       vcpu->arch.gprs[i + 2], vcpu->arch.gprs[i + 3]);
+	}
+	kvm_debug("\thi: 0x%08lx\n", vcpu->arch.hi);
+	kvm_debug("\tlo: 0x%08lx\n", vcpu->arch.lo);
+
+	cop0 = &vcpu->arch.cop0;
+	kvm_debug("\tStatus: 0x%08x, Cause: 0x%08x\n",
+		  kvm_read_c0_guest_status(cop0),
+		  kvm_read_c0_guest_cause(cop0));
+
+	kvm_debug("\tEPC: 0x%08lx\n", kvm_read_c0_guest_epc(cop0));
+
+	return 0;
+}
+
+int kvm_arch_vcpu_ioctl_set_regs(struct kvm_vcpu *vcpu, struct kvm_regs *regs)
+{
+	int i;
+
+	vcpu_load(vcpu);
+
+	for (i = 1; i < ARRAY_SIZE(vcpu->arch.gprs); i++)
+		vcpu->arch.gprs[i] = regs->gpr[i];
+	vcpu->arch.gprs[0] = 0; /* zero is special, and cannot be set. */
+	vcpu->arch.hi = regs->hi;
+	vcpu->arch.lo = regs->lo;
+	vcpu->arch.pc = regs->pc;
+
+	vcpu_put(vcpu);
+	return 0;
+}
+
+int kvm_arch_vcpu_ioctl_get_regs(struct kvm_vcpu *vcpu, struct kvm_regs *regs)
+{
+	int i;
+
+	vcpu_load(vcpu);
+
+	for (i = 0; i < ARRAY_SIZE(vcpu->arch.gprs); i++)
+		regs->gpr[i] = vcpu->arch.gprs[i];
+
+	regs->hi = vcpu->arch.hi;
+	regs->lo = vcpu->arch.lo;
+	regs->pc = vcpu->arch.pc;
+
+	vcpu_put(vcpu);
+	return 0;
+}
+
+int kvm_arch_vcpu_ioctl_translate(struct kvm_vcpu *vcpu,
+				  struct kvm_translation *tr)
+{
+	return 0;
+}
+
+static void kvm_mips_set_c0_status(void)
+{
+	u32 status = read_c0_status();
+
+	if (cpu_has_dsp)
+		status |= (ST0_MX);
+
+	write_c0_status(status);
+	ehb();
+}
+
+/*
+ * Return value is in the form (errcode<<2 | RESUME_FLAG_HOST | RESUME_FLAG_NV)
+ */
+static int __kvm_mips_handle_exit(struct kvm_vcpu *vcpu)
+{
+	struct kvm_run *run = vcpu->run;
+	u32 cause = vcpu->arch.host_cp0_cause;
+	u32 exccode = (cause >> CAUSEB_EXCCODE) & 0x1f;
+	u32 __user *opc = (u32 __user *) vcpu->arch.pc;
+	unsigned long badvaddr = vcpu->arch.host_cp0_badvaddr;
+	enum emulation_result er = EMULATE_DONE;
+	u32 inst;
+	int ret = RESUME_GUEST;
+
+	vcpu->mode = OUTSIDE_GUEST_MODE;
+
+	/* Set a default exit reason */
+	run->exit_reason = KVM_EXIT_UNKNOWN;
+	run->ready_for_interrupt_injection = 1;
+
+	/*
+	 * Set the appropriate status bits based on host CPU features,
+	 * before we hit the scheduler
+	 */
+	kvm_mips_set_c0_status();
+
+	local_irq_enable();
+
+	kvm_debug("kvm_mips_handle_exit: cause: %#x, PC: %p, kvm_run: %p, kvm_vcpu: %p\n",
+			cause, opc, run, vcpu);
+	trace_kvm_exit(vcpu, exccode);
+
+	switch (exccode) {
+	case EXCCODE_INT:
+		kvm_debug("[%d]EXCCODE_INT @ %p\n", vcpu->vcpu_id, opc);
+
+		++vcpu->stat.int_exits;
+
+		if (need_resched())
+			cond_resched();
+
+		ret = RESUME_GUEST;
+		break;
+
+	case EXCCODE_CPU:
+		kvm_debug("EXCCODE_CPU: @ PC: %p\n", opc);
+
+		++vcpu->stat.cop_unusable_exits;
+		ret = kvm_mips_callbacks->handle_cop_unusable(vcpu);
+		/* XXXKYMA: Might need to return to user space */
+		if (run->exit_reason == KVM_EXIT_IRQ_WINDOW_OPEN)
+			ret = RESUME_HOST;
+		break;
+
+	case EXCCODE_MOD:
+		++vcpu->stat.tlbmod_exits;
+		ret = kvm_mips_callbacks->handle_tlb_mod(vcpu);
+		break;
+
+	case EXCCODE_TLBS:
+		kvm_debug("TLB ST fault:  cause %#x, status %#x, PC: %p, BadVaddr: %#lx\n",
+			  cause, kvm_read_c0_guest_status(&vcpu->arch.cop0), opc,
+			  badvaddr);
+
+		++vcpu->stat.tlbmiss_st_exits;
+		ret = kvm_mips_callbacks->handle_tlb_st_miss(vcpu);
+		break;
+
+	case EXCCODE_TLBL:
+		kvm_debug("TLB LD fault: cause %#x, PC: %p, BadVaddr: %#lx\n",
+			  cause, opc, badvaddr);
+
+		++vcpu->stat.tlbmiss_ld_exits;
+		ret = kvm_mips_callbacks->handle_tlb_ld_miss(vcpu);
+		break;
+
+	case EXCCODE_ADES:
+		++vcpu->stat.addrerr_st_exits;
+		ret = kvm_mips_callbacks->handle_addr_err_st(vcpu);
+		break;
+
+	case EXCCODE_ADEL:
+		++vcpu->stat.addrerr_ld_exits;
+		ret = kvm_mips_callbacks->handle_addr_err_ld(vcpu);
+		break;
+
+	case EXCCODE_SYS:
+		++vcpu->stat.syscall_exits;
+		ret = kvm_mips_callbacks->handle_syscall(vcpu);
+		break;
+
+	case EXCCODE_RI:
+		++vcpu->stat.resvd_inst_exits;
+		ret = kvm_mips_callbacks->handle_res_inst(vcpu);
+		break;
+
+	case EXCCODE_BP:
+		++vcpu->stat.break_inst_exits;
+		ret = kvm_mips_callbacks->handle_break(vcpu);
+		break;
+
+	case EXCCODE_TR:
+		++vcpu->stat.trap_inst_exits;
+		ret = kvm_mips_callbacks->handle_trap(vcpu);
+		break;
+
+	case EXCCODE_MSAFPE:
+		++vcpu->stat.msa_fpe_exits;
+		ret = kvm_mips_callbacks->handle_msa_fpe(vcpu);
+		break;
+
+	case EXCCODE_FPE:
+		++vcpu->stat.fpe_exits;
+		ret = kvm_mips_callbacks->handle_fpe(vcpu);
+		break;
+
+	case EXCCODE_MSADIS:
+		++vcpu->stat.msa_disabled_exits;
+		ret = kvm_mips_callbacks->handle_msa_disabled(vcpu);
+		break;
+
+	case EXCCODE_GE:
+		/* defer exit accounting to handler */
+		ret = kvm_mips_callbacks->handle_guest_exit(vcpu);
+		break;
+
+	default:
+		if (cause & CAUSEF_BD)
+			opc += 1;
+		inst = 0;
+		kvm_get_badinstr(opc, vcpu, &inst);
+		kvm_err("Exception Code: %d, not yet handled, @ PC: %p, inst: 0x%08x  BadVaddr: %#lx Status: %#x\n",
+			exccode, opc, inst, badvaddr,
+			kvm_read_c0_guest_status(&vcpu->arch.cop0));
+		kvm_arch_vcpu_dump_regs(vcpu);
+		run->exit_reason = KVM_EXIT_INTERNAL_ERROR;
+		ret = RESUME_HOST;
+		break;
+
+	}
+
+	local_irq_disable();
+
+	if (ret == RESUME_GUEST)
+		kvm_vz_acquire_htimer(vcpu);
+
+	if (er == EMULATE_DONE && !(ret & RESUME_HOST))
+		kvm_mips_deliver_interrupts(vcpu, cause);
+
+	if (!(ret & RESUME_HOST)) {
+		/* Only check for signals if not already exiting to userspace */
+		if (signal_pending(current)) {
+			run->exit_reason = KVM_EXIT_INTR;
+			ret = (-EINTR << 2) | RESUME_HOST;
+			++vcpu->stat.signal_exits;
+			trace_kvm_exit(vcpu, KVM_TRACE_EXIT_SIGNAL);
+		}
+	}
+
+	if (ret == RESUME_GUEST) {
+		trace_kvm_reenter(vcpu);
+
+		/*
+		 * Make sure the read of VCPU requests in vcpu_reenter()
+		 * callback is not reordered ahead of the write to vcpu->mode,
+		 * or we could miss a TLB flush request while the requester sees
+		 * the VCPU as outside of guest mode and not needing an IPI.
+		 */
+		smp_store_mb(vcpu->mode, IN_GUEST_MODE);
+
+		kvm_mips_callbacks->vcpu_reenter(vcpu);
+
+		/*
+		 * If FPU / MSA are enabled (i.e. the guest's FPU / MSA context
+		 * is live), restore FCR31 / MSACSR.
+		 *
+		 * This should be before returning to the guest exception
+		 * vector, as it may well cause an [MSA] FP exception if there
+		 * are pending exception bits unmasked. (see
+		 * kvm_mips_csr_die_notifier() for how that is handled).
+		 */
+		if (kvm_mips_guest_has_fpu(&vcpu->arch) &&
+		    read_c0_status() & ST0_CU1)
+			__kvm_restore_fcsr(&vcpu->arch);
+
+		if (kvm_mips_guest_has_msa(&vcpu->arch) &&
+		    read_c0_config5() & MIPS_CONF5_MSAEN)
+			__kvm_restore_msacsr(&vcpu->arch);
+	}
+	return ret;
+}
+
+int noinstr kvm_mips_handle_exit(struct kvm_vcpu *vcpu)
+{
+	int ret;
+
+	guest_state_exit_irqoff();
+	ret = __kvm_mips_handle_exit(vcpu);
+	guest_state_enter_irqoff();
+
+	return ret;
+}
+
+/* Enable FPU for guest and restore context */
+void kvm_own_fpu(struct kvm_vcpu *vcpu)
+{
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
+	unsigned int sr, cfg5;
+
+	preempt_disable();
+
+	sr = kvm_read_c0_guest_status(cop0);
+
+	/*
+	 * If MSA state is already live, it is undefined how it interacts with
+	 * FR=0 FPU state, and we don't want to hit reserved instruction
+	 * exceptions trying to save the MSA state later when CU=1 && FR=1, so
+	 * play it safe and save it first.
+	 */
+	if (cpu_has_msa && sr & ST0_CU1 && !(sr & ST0_FR) &&
+	    vcpu->arch.aux_inuse & KVM_MIPS_AUX_MSA)
+		kvm_lose_fpu(vcpu);
+
+	/*
+	 * Enable FPU for guest
+	 * We set FR and FRE according to guest context
+	 */
+	change_c0_status(ST0_CU1 | ST0_FR, sr);
+	if (cpu_has_fre) {
+		cfg5 = kvm_read_c0_guest_config5(cop0);
+		change_c0_config5(MIPS_CONF5_FRE, cfg5);
+	}
+	enable_fpu_hazard();
+
+	/* If guest FPU state not active, restore it now */
+	if (!(vcpu->arch.aux_inuse & KVM_MIPS_AUX_FPU)) {
+		__kvm_restore_fpu(&vcpu->arch);
+		vcpu->arch.aux_inuse |= KVM_MIPS_AUX_FPU;
+		trace_kvm_aux(vcpu, KVM_TRACE_AUX_RESTORE, KVM_TRACE_AUX_FPU);
+	} else {
+		trace_kvm_aux(vcpu, KVM_TRACE_AUX_ENABLE, KVM_TRACE_AUX_FPU);
+	}
+
+	preempt_enable();
+}
+
+#ifdef CONFIG_CPU_HAS_MSA
+/* Enable MSA for guest and restore context */
+void kvm_own_msa(struct kvm_vcpu *vcpu)
+{
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
+	unsigned int sr, cfg5;
+
+	preempt_disable();
+
+	/*
+	 * Enable FPU if enabled in guest, since we're restoring FPU context
+	 * anyway. We set FR and FRE according to guest context.
+	 */
+	if (kvm_mips_guest_has_fpu(&vcpu->arch)) {
+		sr = kvm_read_c0_guest_status(cop0);
+
+		/*
+		 * If FR=0 FPU state is already live, it is undefined how it
+		 * interacts with MSA state, so play it safe and save it first.
+		 */
+		if (!(sr & ST0_FR) &&
+		    (vcpu->arch.aux_inuse & (KVM_MIPS_AUX_FPU |
+				KVM_MIPS_AUX_MSA)) == KVM_MIPS_AUX_FPU)
+			kvm_lose_fpu(vcpu);
+
+		change_c0_status(ST0_CU1 | ST0_FR, sr);
+		if (sr & ST0_CU1 && cpu_has_fre) {
+			cfg5 = kvm_read_c0_guest_config5(cop0);
+			change_c0_config5(MIPS_CONF5_FRE, cfg5);
+		}
+	}
+
+	/* Enable MSA for guest */
+	set_c0_config5(MIPS_CONF5_MSAEN);
+	enable_fpu_hazard();
+
+	switch (vcpu->arch.aux_inuse & (KVM_MIPS_AUX_FPU | KVM_MIPS_AUX_MSA)) {
+	case KVM_MIPS_AUX_FPU:
+		/*
+		 * Guest FPU state already loaded, only restore upper MSA state
+		 */
+		__kvm_restore_msa_upper(&vcpu->arch);
+		vcpu->arch.aux_inuse |= KVM_MIPS_AUX_MSA;
+		trace_kvm_aux(vcpu, KVM_TRACE_AUX_RESTORE, KVM_TRACE_AUX_MSA);
+		break;
+	case 0:
+		/* Neither FPU or MSA already active, restore full MSA state */
+		__kvm_restore_msa(&vcpu->arch);
+		vcpu->arch.aux_inuse |= KVM_MIPS_AUX_MSA;
+		if (kvm_mips_guest_has_fpu(&vcpu->arch))
+			vcpu->arch.aux_inuse |= KVM_MIPS_AUX_FPU;
+		trace_kvm_aux(vcpu, KVM_TRACE_AUX_RESTORE,
+			      KVM_TRACE_AUX_FPU_MSA);
+		break;
+	default:
+		trace_kvm_aux(vcpu, KVM_TRACE_AUX_ENABLE, KVM_TRACE_AUX_MSA);
+		break;
+	}
+
+	preempt_enable();
+}
+#endif
+
+/* Drop FPU & MSA without saving it */
+void kvm_drop_fpu(struct kvm_vcpu *vcpu)
+{
+	preempt_disable();
+	if (cpu_has_msa && vcpu->arch.aux_inuse & KVM_MIPS_AUX_MSA) {
+		disable_msa();
+		trace_kvm_aux(vcpu, KVM_TRACE_AUX_DISCARD, KVM_TRACE_AUX_MSA);
+		vcpu->arch.aux_inuse &= ~KVM_MIPS_AUX_MSA;
+	}
+	if (vcpu->arch.aux_inuse & KVM_MIPS_AUX_FPU) {
+		clear_c0_status(ST0_CU1 | ST0_FR);
+		trace_kvm_aux(vcpu, KVM_TRACE_AUX_DISCARD, KVM_TRACE_AUX_FPU);
+		vcpu->arch.aux_inuse &= ~KVM_MIPS_AUX_FPU;
+	}
+	preempt_enable();
+}
+
+/* Save and disable FPU & MSA */
+void kvm_lose_fpu(struct kvm_vcpu *vcpu)
+{
+	/*
+	 * With T&E, FPU & MSA get disabled in root context (hardware) when it
+	 * is disabled in guest context (software), but the register state in
+	 * the hardware may still be in use.
+	 * This is why we explicitly re-enable the hardware before saving.
+	 */
+
+	preempt_disable();
+	if (cpu_has_msa && vcpu->arch.aux_inuse & KVM_MIPS_AUX_MSA) {
+		__kvm_save_msa(&vcpu->arch);
+		trace_kvm_aux(vcpu, KVM_TRACE_AUX_SAVE, KVM_TRACE_AUX_FPU_MSA);
+
+		/* Disable MSA & FPU */
+		disable_msa();
+		if (vcpu->arch.aux_inuse & KVM_MIPS_AUX_FPU) {
+			clear_c0_status(ST0_CU1 | ST0_FR);
+			disable_fpu_hazard();
+		}
+		vcpu->arch.aux_inuse &= ~(KVM_MIPS_AUX_FPU | KVM_MIPS_AUX_MSA);
+	} else if (vcpu->arch.aux_inuse & KVM_MIPS_AUX_FPU) {
+		__kvm_save_fpu(&vcpu->arch);
+		vcpu->arch.aux_inuse &= ~KVM_MIPS_AUX_FPU;
+		trace_kvm_aux(vcpu, KVM_TRACE_AUX_SAVE, KVM_TRACE_AUX_FPU);
+
+		/* Disable FPU */
+		clear_c0_status(ST0_CU1 | ST0_FR);
+		disable_fpu_hazard();
+	}
+	preempt_enable();
+}
+
+/*
+ * Step over a specific ctc1 to FCSR and a specific ctcmsa to MSACSR which are
+ * used to restore guest FCSR/MSACSR state and may trigger a "harmless" FP/MSAFP
+ * exception if cause bits are set in the value being written.
+ */
+static int kvm_mips_csr_die_notify(struct notifier_block *self,
+				   unsigned long cmd, void *ptr)
+{
+	struct die_args *args = (struct die_args *)ptr;
+	struct pt_regs *regs = args->regs;
+	unsigned long pc;
+
+	/* Only interested in FPE and MSAFPE */
+	if (cmd != DIE_FP && cmd != DIE_MSAFP)
+		return NOTIFY_DONE;
+
+	/* Return immediately if guest context isn't active */
+	if (!(current->flags & PF_VCPU))
+		return NOTIFY_DONE;
+
+	/* Should never get here from user mode */
+	BUG_ON(user_mode(regs));
+
+	pc = instruction_pointer(regs);
+	switch (cmd) {
+	case DIE_FP:
+		/* match 2nd instruction in __kvm_restore_fcsr */
+		if (pc != (unsigned long)&__kvm_restore_fcsr + 4)
+			return NOTIFY_DONE;
+		break;
+	case DIE_MSAFP:
+		/* match 2nd/3rd instruction in __kvm_restore_msacsr */
+		if (!cpu_has_msa ||
+		    pc < (unsigned long)&__kvm_restore_msacsr + 4 ||
+		    pc > (unsigned long)&__kvm_restore_msacsr + 8)
+			return NOTIFY_DONE;
+		break;
+	}
+
+	/* Move PC forward a little and continue executing */
+	instruction_pointer(regs) += 4;
+
+	return NOTIFY_STOP;
+}
+
+static struct notifier_block kvm_mips_csr_die_notifier = {
+	.notifier_call = kvm_mips_csr_die_notify,
+};
+
+static u32 kvm_default_priority_to_irq[MIPS_EXC_MAX] = {
+	[MIPS_EXC_INT_TIMER] = C_IRQ5,
+	[MIPS_EXC_INT_IO_1]  = C_IRQ0,
+	[MIPS_EXC_INT_IPI_1] = C_IRQ1,
+	[MIPS_EXC_INT_IPI_2] = C_IRQ2,
+};
+
+static u32 kvm_loongson3_priority_to_irq[MIPS_EXC_MAX] = {
+	[MIPS_EXC_INT_TIMER] = C_IRQ5,
+	[MIPS_EXC_INT_IO_1]  = C_IRQ0,
+	[MIPS_EXC_INT_IO_2]  = C_IRQ1,
+	[MIPS_EXC_INT_IPI_1] = C_IRQ4,
+};
+
+u32 *kvm_priority_to_irq = kvm_default_priority_to_irq;
+
+u32 kvm_irq_to_priority(u32 irq)
+{
+	int i;
+
+	for (i = MIPS_EXC_INT_TIMER; i < MIPS_EXC_MAX; i++) {
+		if (kvm_priority_to_irq[i] == (1 << (irq + 8)))
+			return i;
+	}
+
+	return MIPS_EXC_MAX;
+}
+
+static int __init kvm_mips_init(void)
+{
+	int ret;
+
+	if (cpu_has_mmid) {
+		pr_warn("KVM does not yet support MMIDs. KVM Disabled\n");
+		return -EOPNOTSUPP;
+	}
+
+	ret = kvm_mips_entry_setup();
+	if (ret)
+		return ret;
+
+	ret = kvm_init(NULL, sizeof(struct kvm_vcpu), 0, THIS_MODULE);
+
+	if (ret)
+		return ret;
+
+	if (boot_cpu_type() == CPU_LOONGSON64)
+		kvm_priority_to_irq = kvm_loongson3_priority_to_irq;
+
+	register_die_notifier(&kvm_mips_csr_die_notifier);
+
+	return 0;
+}
+
+static void __exit kvm_mips_exit(void)
+{
+	kvm_exit();
+
+	unregister_die_notifier(&kvm_mips_csr_die_notifier);
+}
+
+module_init(kvm_mips_init);
+module_exit(kvm_mips_exit);
+
+EXPORT_TRACEPOINT_SYMBOL(kvm_exit);
diff --git a/arch/mips/kvm/mmu.c b/arch/mips/kvm/mmu.c
new file mode 100644
index 000000000..19ec27be2
--- /dev/null
+++ b/arch/mips/kvm/mmu.c
@@ -0,0 +1,758 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * KVM/MIPS MMU handling in the KVM module.
+ *
+ * Copyright (C) 2012  MIPS Technologies, Inc.  All rights reserved.
+ * Authors: Sanjay Lal <sanjayl@kymasys.com>
+ */
+
+#include <linux/highmem.h>
+#include <linux/kvm_host.h>
+#include <linux/uaccess.h>
+#include <asm/mmu_context.h>
+#include <asm/pgalloc.h>
+
+/*
+ * KVM_MMU_CACHE_MIN_PAGES is the number of GPA page table translation levels
+ * for which pages need to be cached.
+ */
+#if defined(__PAGETABLE_PMD_FOLDED)
+#define KVM_MMU_CACHE_MIN_PAGES 1
+#else
+#define KVM_MMU_CACHE_MIN_PAGES 2
+#endif
+
+void kvm_mmu_free_memory_caches(struct kvm_vcpu *vcpu)
+{
+	kvm_mmu_free_memory_cache(&vcpu->arch.mmu_page_cache);
+}
+
+/**
+ * kvm_pgd_init() - Initialise KVM GPA page directory.
+ * @page:	Pointer to page directory (PGD) for KVM GPA.
+ *
+ * Initialise a KVM GPA page directory with pointers to the invalid table, i.e.
+ * representing no mappings. This is similar to pgd_init(), however it
+ * initialises all the page directory pointers, not just the ones corresponding
+ * to the userland address space (since it is for the guest physical address
+ * space rather than a virtual address space).
+ */
+static void kvm_pgd_init(void *page)
+{
+	unsigned long *p, *end;
+	unsigned long entry;
+
+#ifdef __PAGETABLE_PMD_FOLDED
+	entry = (unsigned long)invalid_pte_table;
+#else
+	entry = (unsigned long)invalid_pmd_table;
+#endif
+
+	p = (unsigned long *)page;
+	end = p + PTRS_PER_PGD;
+
+	do {
+		p[0] = entry;
+		p[1] = entry;
+		p[2] = entry;
+		p[3] = entry;
+		p[4] = entry;
+		p += 8;
+		p[-3] = entry;
+		p[-2] = entry;
+		p[-1] = entry;
+	} while (p != end);
+}
+
+/**
+ * kvm_pgd_alloc() - Allocate and initialise a KVM GPA page directory.
+ *
+ * Allocate a blank KVM GPA page directory (PGD) for representing guest physical
+ * to host physical page mappings.
+ *
+ * Returns:	Pointer to new KVM GPA page directory.
+ *		NULL on allocation failure.
+ */
+pgd_t *kvm_pgd_alloc(void)
+{
+	pgd_t *ret;
+
+	ret = (pgd_t *)__get_free_pages(GFP_KERNEL, PGD_TABLE_ORDER);
+	if (ret)
+		kvm_pgd_init(ret);
+
+	return ret;
+}
+
+/**
+ * kvm_mips_walk_pgd() - Walk page table with optional allocation.
+ * @pgd:	Page directory pointer.
+ * @addr:	Address to index page table using.
+ * @cache:	MMU page cache to allocate new page tables from, or NULL.
+ *
+ * Walk the page tables pointed to by @pgd to find the PTE corresponding to the
+ * address @addr. If page tables don't exist for @addr, they will be created
+ * from the MMU cache if @cache is not NULL.
+ *
+ * Returns:	Pointer to pte_t corresponding to @addr.
+ *		NULL if a page table doesn't exist for @addr and !@cache.
+ *		NULL if a page table allocation failed.
+ */
+static pte_t *kvm_mips_walk_pgd(pgd_t *pgd, struct kvm_mmu_memory_cache *cache,
+				unsigned long addr)
+{
+	p4d_t *p4d;
+	pud_t *pud;
+	pmd_t *pmd;
+
+	pgd += pgd_index(addr);
+	if (pgd_none(*pgd)) {
+		/* Not used on MIPS yet */
+		BUG();
+		return NULL;
+	}
+	p4d = p4d_offset(pgd, addr);
+	pud = pud_offset(p4d, addr);
+	if (pud_none(*pud)) {
+		pmd_t *new_pmd;
+
+		if (!cache)
+			return NULL;
+		new_pmd = kvm_mmu_memory_cache_alloc(cache);
+		pmd_init((unsigned long)new_pmd,
+			 (unsigned long)invalid_pte_table);
+		pud_populate(NULL, pud, new_pmd);
+	}
+	pmd = pmd_offset(pud, addr);
+	if (pmd_none(*pmd)) {
+		pte_t *new_pte;
+
+		if (!cache)
+			return NULL;
+		new_pte = kvm_mmu_memory_cache_alloc(cache);
+		clear_page(new_pte);
+		pmd_populate_kernel(NULL, pmd, new_pte);
+	}
+	return pte_offset_kernel(pmd, addr);
+}
+
+/* Caller must hold kvm->mm_lock */
+static pte_t *kvm_mips_pte_for_gpa(struct kvm *kvm,
+				   struct kvm_mmu_memory_cache *cache,
+				   unsigned long addr)
+{
+	return kvm_mips_walk_pgd(kvm->arch.gpa_mm.pgd, cache, addr);
+}
+
+/*
+ * kvm_mips_flush_gpa_{pte,pmd,pud,pgd,pt}.
+ * Flush a range of guest physical address space from the VM's GPA page tables.
+ */
+
+static bool kvm_mips_flush_gpa_pte(pte_t *pte, unsigned long start_gpa,
+				   unsigned long end_gpa)
+{
+	int i_min = pte_index(start_gpa);
+	int i_max = pte_index(end_gpa);
+	bool safe_to_remove = (i_min == 0 && i_max == PTRS_PER_PTE - 1);
+	int i;
+
+	for (i = i_min; i <= i_max; ++i) {
+		if (!pte_present(pte[i]))
+			continue;
+
+		set_pte(pte + i, __pte(0));
+	}
+	return safe_to_remove;
+}
+
+static bool kvm_mips_flush_gpa_pmd(pmd_t *pmd, unsigned long start_gpa,
+				   unsigned long end_gpa)
+{
+	pte_t *pte;
+	unsigned long end = ~0ul;
+	int i_min = pmd_index(start_gpa);
+	int i_max = pmd_index(end_gpa);
+	bool safe_to_remove = (i_min == 0 && i_max == PTRS_PER_PMD - 1);
+	int i;
+
+	for (i = i_min; i <= i_max; ++i, start_gpa = 0) {
+		if (!pmd_present(pmd[i]))
+			continue;
+
+		pte = pte_offset_kernel(pmd + i, 0);
+		if (i == i_max)
+			end = end_gpa;
+
+		if (kvm_mips_flush_gpa_pte(pte, start_gpa, end)) {
+			pmd_clear(pmd + i);
+			pte_free_kernel(NULL, pte);
+		} else {
+			safe_to_remove = false;
+		}
+	}
+	return safe_to_remove;
+}
+
+static bool kvm_mips_flush_gpa_pud(pud_t *pud, unsigned long start_gpa,
+				   unsigned long end_gpa)
+{
+	pmd_t *pmd;
+	unsigned long end = ~0ul;
+	int i_min = pud_index(start_gpa);
+	int i_max = pud_index(end_gpa);
+	bool safe_to_remove = (i_min == 0 && i_max == PTRS_PER_PUD - 1);
+	int i;
+
+	for (i = i_min; i <= i_max; ++i, start_gpa = 0) {
+		if (!pud_present(pud[i]))
+			continue;
+
+		pmd = pmd_offset(pud + i, 0);
+		if (i == i_max)
+			end = end_gpa;
+
+		if (kvm_mips_flush_gpa_pmd(pmd, start_gpa, end)) {
+			pud_clear(pud + i);
+			pmd_free(NULL, pmd);
+		} else {
+			safe_to_remove = false;
+		}
+	}
+	return safe_to_remove;
+}
+
+static bool kvm_mips_flush_gpa_pgd(pgd_t *pgd, unsigned long start_gpa,
+				   unsigned long end_gpa)
+{
+	p4d_t *p4d;
+	pud_t *pud;
+	unsigned long end = ~0ul;
+	int i_min = pgd_index(start_gpa);
+	int i_max = pgd_index(end_gpa);
+	bool safe_to_remove = (i_min == 0 && i_max == PTRS_PER_PGD - 1);
+	int i;
+
+	for (i = i_min; i <= i_max; ++i, start_gpa = 0) {
+		if (!pgd_present(pgd[i]))
+			continue;
+
+		p4d = p4d_offset(pgd, 0);
+		pud = pud_offset(p4d + i, 0);
+		if (i == i_max)
+			end = end_gpa;
+
+		if (kvm_mips_flush_gpa_pud(pud, start_gpa, end)) {
+			pgd_clear(pgd + i);
+			pud_free(NULL, pud);
+		} else {
+			safe_to_remove = false;
+		}
+	}
+	return safe_to_remove;
+}
+
+/**
+ * kvm_mips_flush_gpa_pt() - Flush a range of guest physical addresses.
+ * @kvm:	KVM pointer.
+ * @start_gfn:	Guest frame number of first page in GPA range to flush.
+ * @end_gfn:	Guest frame number of last page in GPA range to flush.
+ *
+ * Flushes a range of GPA mappings from the GPA page tables.
+ *
+ * The caller must hold the @kvm->mmu_lock spinlock.
+ *
+ * Returns:	Whether its safe to remove the top level page directory because
+ *		all lower levels have been removed.
+ */
+bool kvm_mips_flush_gpa_pt(struct kvm *kvm, gfn_t start_gfn, gfn_t end_gfn)
+{
+	return kvm_mips_flush_gpa_pgd(kvm->arch.gpa_mm.pgd,
+				      start_gfn << PAGE_SHIFT,
+				      end_gfn << PAGE_SHIFT);
+}
+
+#define BUILD_PTE_RANGE_OP(name, op)					\
+static int kvm_mips_##name##_pte(pte_t *pte, unsigned long start,	\
+				 unsigned long end)			\
+{									\
+	int ret = 0;							\
+	int i_min = pte_index(start);				\
+	int i_max = pte_index(end);					\
+	int i;								\
+	pte_t old, new;							\
+									\
+	for (i = i_min; i <= i_max; ++i) {				\
+		if (!pte_present(pte[i]))				\
+			continue;					\
+									\
+		old = pte[i];						\
+		new = op(old);						\
+		if (pte_val(new) == pte_val(old))			\
+			continue;					\
+		set_pte(pte + i, new);					\
+		ret = 1;						\
+	}								\
+	return ret;							\
+}									\
+									\
+/* returns true if anything was done */					\
+static int kvm_mips_##name##_pmd(pmd_t *pmd, unsigned long start,	\
+				 unsigned long end)			\
+{									\
+	int ret = 0;							\
+	pte_t *pte;							\
+	unsigned long cur_end = ~0ul;					\
+	int i_min = pmd_index(start);				\
+	int i_max = pmd_index(end);					\
+	int i;								\
+									\
+	for (i = i_min; i <= i_max; ++i, start = 0) {			\
+		if (!pmd_present(pmd[i]))				\
+			continue;					\
+									\
+		pte = pte_offset_kernel(pmd + i, 0);				\
+		if (i == i_max)						\
+			cur_end = end;					\
+									\
+		ret |= kvm_mips_##name##_pte(pte, start, cur_end);	\
+	}								\
+	return ret;							\
+}									\
+									\
+static int kvm_mips_##name##_pud(pud_t *pud, unsigned long start,	\
+				 unsigned long end)			\
+{									\
+	int ret = 0;							\
+	pmd_t *pmd;							\
+	unsigned long cur_end = ~0ul;					\
+	int i_min = pud_index(start);				\
+	int i_max = pud_index(end);					\
+	int i;								\
+									\
+	for (i = i_min; i <= i_max; ++i, start = 0) {			\
+		if (!pud_present(pud[i]))				\
+			continue;					\
+									\
+		pmd = pmd_offset(pud + i, 0);				\
+		if (i == i_max)						\
+			cur_end = end;					\
+									\
+		ret |= kvm_mips_##name##_pmd(pmd, start, cur_end);	\
+	}								\
+	return ret;							\
+}									\
+									\
+static int kvm_mips_##name##_pgd(pgd_t *pgd, unsigned long start,	\
+				 unsigned long end)			\
+{									\
+	int ret = 0;							\
+	p4d_t *p4d;							\
+	pud_t *pud;							\
+	unsigned long cur_end = ~0ul;					\
+	int i_min = pgd_index(start);					\
+	int i_max = pgd_index(end);					\
+	int i;								\
+									\
+	for (i = i_min; i <= i_max; ++i, start = 0) {			\
+		if (!pgd_present(pgd[i]))				\
+			continue;					\
+									\
+		p4d = p4d_offset(pgd, 0);				\
+		pud = pud_offset(p4d + i, 0);				\
+		if (i == i_max)						\
+			cur_end = end;					\
+									\
+		ret |= kvm_mips_##name##_pud(pud, start, cur_end);	\
+	}								\
+	return ret;							\
+}
+
+/*
+ * kvm_mips_mkclean_gpa_pt.
+ * Mark a range of guest physical address space clean (writes fault) in the VM's
+ * GPA page table to allow dirty page tracking.
+ */
+
+BUILD_PTE_RANGE_OP(mkclean, pte_mkclean)
+
+/**
+ * kvm_mips_mkclean_gpa_pt() - Make a range of guest physical addresses clean.
+ * @kvm:	KVM pointer.
+ * @start_gfn:	Guest frame number of first page in GPA range to flush.
+ * @end_gfn:	Guest frame number of last page in GPA range to flush.
+ *
+ * Make a range of GPA mappings clean so that guest writes will fault and
+ * trigger dirty page logging.
+ *
+ * The caller must hold the @kvm->mmu_lock spinlock.
+ *
+ * Returns:	Whether any GPA mappings were modified, which would require
+ *		derived mappings (GVA page tables & TLB enties) to be
+ *		invalidated.
+ */
+int kvm_mips_mkclean_gpa_pt(struct kvm *kvm, gfn_t start_gfn, gfn_t end_gfn)
+{
+	return kvm_mips_mkclean_pgd(kvm->arch.gpa_mm.pgd,
+				    start_gfn << PAGE_SHIFT,
+				    end_gfn << PAGE_SHIFT);
+}
+
+/**
+ * kvm_arch_mmu_enable_log_dirty_pt_masked() - write protect dirty pages
+ * @kvm:	The KVM pointer
+ * @slot:	The memory slot associated with mask
+ * @gfn_offset:	The gfn offset in memory slot
+ * @mask:	The mask of dirty pages at offset 'gfn_offset' in this memory
+ *		slot to be write protected
+ *
+ * Walks bits set in mask write protects the associated pte's. Caller must
+ * acquire @kvm->mmu_lock.
+ */
+void kvm_arch_mmu_enable_log_dirty_pt_masked(struct kvm *kvm,
+		struct kvm_memory_slot *slot,
+		gfn_t gfn_offset, unsigned long mask)
+{
+	gfn_t base_gfn = slot->base_gfn + gfn_offset;
+	gfn_t start = base_gfn +  __ffs(mask);
+	gfn_t end = base_gfn + __fls(mask);
+
+	kvm_mips_mkclean_gpa_pt(kvm, start, end);
+}
+
+/*
+ * kvm_mips_mkold_gpa_pt.
+ * Mark a range of guest physical address space old (all accesses fault) in the
+ * VM's GPA page table to allow detection of commonly used pages.
+ */
+
+BUILD_PTE_RANGE_OP(mkold, pte_mkold)
+
+static int kvm_mips_mkold_gpa_pt(struct kvm *kvm, gfn_t start_gfn,
+				 gfn_t end_gfn)
+{
+	return kvm_mips_mkold_pgd(kvm->arch.gpa_mm.pgd,
+				  start_gfn << PAGE_SHIFT,
+				  end_gfn << PAGE_SHIFT);
+}
+
+bool kvm_unmap_gfn_range(struct kvm *kvm, struct kvm_gfn_range *range)
+{
+	kvm_mips_flush_gpa_pt(kvm, range->start, range->end);
+	return true;
+}
+
+bool kvm_set_spte_gfn(struct kvm *kvm, struct kvm_gfn_range *range)
+{
+	gpa_t gpa = range->start << PAGE_SHIFT;
+	pte_t hva_pte = range->pte;
+	pte_t *gpa_pte = kvm_mips_pte_for_gpa(kvm, NULL, gpa);
+	pte_t old_pte;
+
+	if (!gpa_pte)
+		return false;
+
+	/* Mapping may need adjusting depending on memslot flags */
+	old_pte = *gpa_pte;
+	if (range->slot->flags & KVM_MEM_LOG_DIRTY_PAGES && !pte_dirty(old_pte))
+		hva_pte = pte_mkclean(hva_pte);
+	else if (range->slot->flags & KVM_MEM_READONLY)
+		hva_pte = pte_wrprotect(hva_pte);
+
+	set_pte(gpa_pte, hva_pte);
+
+	/* Replacing an absent or old page doesn't need flushes */
+	if (!pte_present(old_pte) || !pte_young(old_pte))
+		return false;
+
+	/* Pages swapped, aged, moved, or cleaned require flushes */
+	return !pte_present(hva_pte) ||
+	       !pte_young(hva_pte) ||
+	       pte_pfn(old_pte) != pte_pfn(hva_pte) ||
+	       (pte_dirty(old_pte) && !pte_dirty(hva_pte));
+}
+
+bool kvm_age_gfn(struct kvm *kvm, struct kvm_gfn_range *range)
+{
+	return kvm_mips_mkold_gpa_pt(kvm, range->start, range->end);
+}
+
+bool kvm_test_age_gfn(struct kvm *kvm, struct kvm_gfn_range *range)
+{
+	gpa_t gpa = range->start << PAGE_SHIFT;
+	pte_t *gpa_pte = kvm_mips_pte_for_gpa(kvm, NULL, gpa);
+
+	if (!gpa_pte)
+		return false;
+	return pte_young(*gpa_pte);
+}
+
+/**
+ * _kvm_mips_map_page_fast() - Fast path GPA fault handler.
+ * @vcpu:		VCPU pointer.
+ * @gpa:		Guest physical address of fault.
+ * @write_fault:	Whether the fault was due to a write.
+ * @out_entry:		New PTE for @gpa (written on success unless NULL).
+ * @out_buddy:		New PTE for @gpa's buddy (written on success unless
+ *			NULL).
+ *
+ * Perform fast path GPA fault handling, doing all that can be done without
+ * calling into KVM. This handles marking old pages young (for idle page
+ * tracking), and dirtying of clean pages (for dirty page logging).
+ *
+ * Returns:	0 on success, in which case we can update derived mappings and
+ *		resume guest execution.
+ *		-EFAULT on failure due to absent GPA mapping or write to
+ *		read-only page, in which case KVM must be consulted.
+ */
+static int _kvm_mips_map_page_fast(struct kvm_vcpu *vcpu, unsigned long gpa,
+				   bool write_fault,
+				   pte_t *out_entry, pte_t *out_buddy)
+{
+	struct kvm *kvm = vcpu->kvm;
+	gfn_t gfn = gpa >> PAGE_SHIFT;
+	pte_t *ptep;
+	kvm_pfn_t pfn = 0;	/* silence bogus GCC warning */
+	bool pfn_valid = false;
+	int ret = 0;
+
+	spin_lock(&kvm->mmu_lock);
+
+	/* Fast path - just check GPA page table for an existing entry */
+	ptep = kvm_mips_pte_for_gpa(kvm, NULL, gpa);
+	if (!ptep || !pte_present(*ptep)) {
+		ret = -EFAULT;
+		goto out;
+	}
+
+	/* Track access to pages marked old */
+	if (!pte_young(*ptep)) {
+		set_pte(ptep, pte_mkyoung(*ptep));
+		pfn = pte_pfn(*ptep);
+		pfn_valid = true;
+		/* call kvm_set_pfn_accessed() after unlock */
+	}
+	if (write_fault && !pte_dirty(*ptep)) {
+		if (!pte_write(*ptep)) {
+			ret = -EFAULT;
+			goto out;
+		}
+
+		/* Track dirtying of writeable pages */
+		set_pte(ptep, pte_mkdirty(*ptep));
+		pfn = pte_pfn(*ptep);
+		mark_page_dirty(kvm, gfn);
+		kvm_set_pfn_dirty(pfn);
+	}
+
+	if (out_entry)
+		*out_entry = *ptep;
+	if (out_buddy)
+		*out_buddy = *ptep_buddy(ptep);
+
+out:
+	spin_unlock(&kvm->mmu_lock);
+	if (pfn_valid)
+		kvm_set_pfn_accessed(pfn);
+	return ret;
+}
+
+/**
+ * kvm_mips_map_page() - Map a guest physical page.
+ * @vcpu:		VCPU pointer.
+ * @gpa:		Guest physical address of fault.
+ * @write_fault:	Whether the fault was due to a write.
+ * @out_entry:		New PTE for @gpa (written on success unless NULL).
+ * @out_buddy:		New PTE for @gpa's buddy (written on success unless
+ *			NULL).
+ *
+ * Handle GPA faults by creating a new GPA mapping (or updating an existing
+ * one).
+ *
+ * This takes care of marking pages young or dirty (idle/dirty page tracking),
+ * asking KVM for the corresponding PFN, and creating a mapping in the GPA page
+ * tables. Derived mappings (GVA page tables and TLBs) must be handled by the
+ * caller.
+ *
+ * Returns:	0 on success, in which case the caller may use the @out_entry
+ *		and @out_buddy PTEs to update derived mappings and resume guest
+ *		execution.
+ *		-EFAULT if there is no memory region at @gpa or a write was
+ *		attempted to a read-only memory region. This is usually handled
+ *		as an MMIO access.
+ */
+static int kvm_mips_map_page(struct kvm_vcpu *vcpu, unsigned long gpa,
+			     bool write_fault,
+			     pte_t *out_entry, pte_t *out_buddy)
+{
+	struct kvm *kvm = vcpu->kvm;
+	struct kvm_mmu_memory_cache *memcache = &vcpu->arch.mmu_page_cache;
+	gfn_t gfn = gpa >> PAGE_SHIFT;
+	int srcu_idx, err;
+	kvm_pfn_t pfn;
+	pte_t *ptep, entry;
+	bool writeable;
+	unsigned long prot_bits;
+	unsigned long mmu_seq;
+
+	/* Try the fast path to handle old / clean pages */
+	srcu_idx = srcu_read_lock(&kvm->srcu);
+	err = _kvm_mips_map_page_fast(vcpu, gpa, write_fault, out_entry,
+				      out_buddy);
+	if (!err)
+		goto out;
+
+	/* We need a minimum of cached pages ready for page table creation */
+	err = kvm_mmu_topup_memory_cache(memcache, KVM_MMU_CACHE_MIN_PAGES);
+	if (err)
+		goto out;
+
+retry:
+	/*
+	 * Used to check for invalidations in progress, of the pfn that is
+	 * returned by pfn_to_pfn_prot below.
+	 */
+	mmu_seq = kvm->mmu_invalidate_seq;
+	/*
+	 * Ensure the read of mmu_invalidate_seq isn't reordered with PTE reads
+	 * in gfn_to_pfn_prot() (which calls get_user_pages()), so that we don't
+	 * risk the page we get a reference to getting unmapped before we have a
+	 * chance to grab the mmu_lock without mmu_invalidate_retry() noticing.
+	 *
+	 * This smp_rmb() pairs with the effective smp_wmb() of the combination
+	 * of the pte_unmap_unlock() after the PTE is zapped, and the
+	 * spin_lock() in kvm_mmu_notifier_invalidate_<page|range_end>() before
+	 * mmu_invalidate_seq is incremented.
+	 */
+	smp_rmb();
+
+	/* Slow path - ask KVM core whether we can access this GPA */
+	pfn = gfn_to_pfn_prot(kvm, gfn, write_fault, &writeable);
+	if (is_error_noslot_pfn(pfn)) {
+		err = -EFAULT;
+		goto out;
+	}
+
+	spin_lock(&kvm->mmu_lock);
+	/* Check if an invalidation has taken place since we got pfn */
+	if (mmu_invalidate_retry(kvm, mmu_seq)) {
+		/*
+		 * This can happen when mappings are changed asynchronously, but
+		 * also synchronously if a COW is triggered by
+		 * gfn_to_pfn_prot().
+		 */
+		spin_unlock(&kvm->mmu_lock);
+		kvm_release_pfn_clean(pfn);
+		goto retry;
+	}
+
+	/* Ensure page tables are allocated */
+	ptep = kvm_mips_pte_for_gpa(kvm, memcache, gpa);
+
+	/* Set up the PTE */
+	prot_bits = _PAGE_PRESENT | __READABLE | _page_cachable_default;
+	if (writeable) {
+		prot_bits |= _PAGE_WRITE;
+		if (write_fault) {
+			prot_bits |= __WRITEABLE;
+			mark_page_dirty(kvm, gfn);
+			kvm_set_pfn_dirty(pfn);
+		}
+	}
+	entry = pfn_pte(pfn, __pgprot(prot_bits));
+
+	/* Write the PTE */
+	set_pte(ptep, entry);
+
+	err = 0;
+	if (out_entry)
+		*out_entry = *ptep;
+	if (out_buddy)
+		*out_buddy = *ptep_buddy(ptep);
+
+	spin_unlock(&kvm->mmu_lock);
+	kvm_release_pfn_clean(pfn);
+	kvm_set_pfn_accessed(pfn);
+out:
+	srcu_read_unlock(&kvm->srcu, srcu_idx);
+	return err;
+}
+
+int kvm_mips_handle_vz_root_tlb_fault(unsigned long badvaddr,
+				      struct kvm_vcpu *vcpu,
+				      bool write_fault)
+{
+	int ret;
+
+	ret = kvm_mips_map_page(vcpu, badvaddr, write_fault, NULL, NULL);
+	if (ret)
+		return ret;
+
+	/* Invalidate this entry in the TLB */
+	return kvm_vz_host_tlb_inv(vcpu, badvaddr);
+}
+
+/**
+ * kvm_mips_migrate_count() - Migrate timer.
+ * @vcpu:	Virtual CPU.
+ *
+ * Migrate CP0_Count hrtimer to the current CPU by cancelling and restarting it
+ * if it was running prior to being cancelled.
+ *
+ * Must be called when the VCPU is migrated to a different CPU to ensure that
+ * timer expiry during guest execution interrupts the guest and causes the
+ * interrupt to be delivered in a timely manner.
+ */
+static void kvm_mips_migrate_count(struct kvm_vcpu *vcpu)
+{
+	if (hrtimer_cancel(&vcpu->arch.comparecount_timer))
+		hrtimer_restart(&vcpu->arch.comparecount_timer);
+}
+
+/* Restore ASID once we are scheduled back after preemption */
+void kvm_arch_vcpu_load(struct kvm_vcpu *vcpu, int cpu)
+{
+	unsigned long flags;
+
+	kvm_debug("%s: vcpu %p, cpu: %d\n", __func__, vcpu, cpu);
+
+	local_irq_save(flags);
+
+	vcpu->cpu = cpu;
+	if (vcpu->arch.last_sched_cpu != cpu) {
+		kvm_debug("[%d->%d]KVM VCPU[%d] switch\n",
+			  vcpu->arch.last_sched_cpu, cpu, vcpu->vcpu_id);
+		/*
+		 * Migrate the timer interrupt to the current CPU so that it
+		 * always interrupts the guest and synchronously triggers a
+		 * guest timer interrupt.
+		 */
+		kvm_mips_migrate_count(vcpu);
+	}
+
+	/* restore guest state to registers */
+	kvm_mips_callbacks->vcpu_load(vcpu, cpu);
+
+	local_irq_restore(flags);
+}
+
+/* ASID can change if another task is scheduled during preemption */
+void kvm_arch_vcpu_put(struct kvm_vcpu *vcpu)
+{
+	unsigned long flags;
+	int cpu;
+
+	local_irq_save(flags);
+
+	cpu = smp_processor_id();
+	vcpu->arch.last_sched_cpu = cpu;
+	vcpu->cpu = -1;
+
+	/* save guest state in registers */
+	kvm_mips_callbacks->vcpu_put(vcpu, cpu);
+
+	local_irq_restore(flags);
+}
diff --git a/arch/mips/kvm/msa.S b/arch/mips/kvm/msa.S
new file mode 100644
index 000000000..d02f0c6cc
--- /dev/null
+++ b/arch/mips/kvm/msa.S
@@ -0,0 +1,161 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * MIPS SIMD Architecture (MSA) context handling code for KVM.
+ *
+ * Copyright (C) 2015 Imagination Technologies Ltd.
+ */
+
+#include <asm/asm.h>
+#include <asm/asm-offsets.h>
+#include <asm/asmmacro.h>
+#include <asm/regdef.h>
+
+	.set	noreorder
+	.set	noat
+
+LEAF(__kvm_save_msa)
+	st_d	0,  VCPU_FPR0,  a0
+	st_d	1,  VCPU_FPR1,  a0
+	st_d	2,  VCPU_FPR2,  a0
+	st_d	3,  VCPU_FPR3,  a0
+	st_d	4,  VCPU_FPR4,  a0
+	st_d	5,  VCPU_FPR5,  a0
+	st_d	6,  VCPU_FPR6,  a0
+	st_d	7,  VCPU_FPR7,  a0
+	st_d	8,  VCPU_FPR8,  a0
+	st_d	9,  VCPU_FPR9,  a0
+	st_d	10, VCPU_FPR10, a0
+	st_d	11, VCPU_FPR11, a0
+	st_d	12, VCPU_FPR12, a0
+	st_d	13, VCPU_FPR13, a0
+	st_d	14, VCPU_FPR14, a0
+	st_d	15, VCPU_FPR15, a0
+	st_d	16, VCPU_FPR16, a0
+	st_d	17, VCPU_FPR17, a0
+	st_d	18, VCPU_FPR18, a0
+	st_d	19, VCPU_FPR19, a0
+	st_d	20, VCPU_FPR20, a0
+	st_d	21, VCPU_FPR21, a0
+	st_d	22, VCPU_FPR22, a0
+	st_d	23, VCPU_FPR23, a0
+	st_d	24, VCPU_FPR24, a0
+	st_d	25, VCPU_FPR25, a0
+	st_d	26, VCPU_FPR26, a0
+	st_d	27, VCPU_FPR27, a0
+	st_d	28, VCPU_FPR28, a0
+	st_d	29, VCPU_FPR29, a0
+	st_d	30, VCPU_FPR30, a0
+	st_d	31, VCPU_FPR31, a0
+	jr	ra
+	 nop
+	END(__kvm_save_msa)
+
+LEAF(__kvm_restore_msa)
+	ld_d	0,  VCPU_FPR0,  a0
+	ld_d	1,  VCPU_FPR1,  a0
+	ld_d	2,  VCPU_FPR2,  a0
+	ld_d	3,  VCPU_FPR3,  a0
+	ld_d	4,  VCPU_FPR4,  a0
+	ld_d	5,  VCPU_FPR5,  a0
+	ld_d	6,  VCPU_FPR6,  a0
+	ld_d	7,  VCPU_FPR7,  a0
+	ld_d	8,  VCPU_FPR8,  a0
+	ld_d	9,  VCPU_FPR9,  a0
+	ld_d	10, VCPU_FPR10, a0
+	ld_d	11, VCPU_FPR11, a0
+	ld_d	12, VCPU_FPR12, a0
+	ld_d	13, VCPU_FPR13, a0
+	ld_d	14, VCPU_FPR14, a0
+	ld_d	15, VCPU_FPR15, a0
+	ld_d	16, VCPU_FPR16, a0
+	ld_d	17, VCPU_FPR17, a0
+	ld_d	18, VCPU_FPR18, a0
+	ld_d	19, VCPU_FPR19, a0
+	ld_d	20, VCPU_FPR20, a0
+	ld_d	21, VCPU_FPR21, a0
+	ld_d	22, VCPU_FPR22, a0
+	ld_d	23, VCPU_FPR23, a0
+	ld_d	24, VCPU_FPR24, a0
+	ld_d	25, VCPU_FPR25, a0
+	ld_d	26, VCPU_FPR26, a0
+	ld_d	27, VCPU_FPR27, a0
+	ld_d	28, VCPU_FPR28, a0
+	ld_d	29, VCPU_FPR29, a0
+	ld_d	30, VCPU_FPR30, a0
+	ld_d	31, VCPU_FPR31, a0
+	jr	ra
+	 nop
+	END(__kvm_restore_msa)
+
+	.macro	kvm_restore_msa_upper	wr, off, base
+	.set	push
+	.set	noat
+#ifdef CONFIG_64BIT
+	ld	$1, \off(\base)
+	insert_d \wr, 1
+#elif defined(CONFIG_CPU_LITTLE_ENDIAN)
+	lw	$1, \off(\base)
+	insert_w \wr, 2
+	lw	$1, (\off+4)(\base)
+	insert_w \wr, 3
+#else /* CONFIG_CPU_BIG_ENDIAN */
+	lw	$1, (\off+4)(\base)
+	insert_w \wr, 2
+	lw	$1, \off(\base)
+	insert_w \wr, 3
+#endif
+	.set	pop
+	.endm
+
+LEAF(__kvm_restore_msa_upper)
+	kvm_restore_msa_upper	0,  VCPU_FPR0 +8, a0
+	kvm_restore_msa_upper	1,  VCPU_FPR1 +8, a0
+	kvm_restore_msa_upper	2,  VCPU_FPR2 +8, a0
+	kvm_restore_msa_upper	3,  VCPU_FPR3 +8, a0
+	kvm_restore_msa_upper	4,  VCPU_FPR4 +8, a0
+	kvm_restore_msa_upper	5,  VCPU_FPR5 +8, a0
+	kvm_restore_msa_upper	6,  VCPU_FPR6 +8, a0
+	kvm_restore_msa_upper	7,  VCPU_FPR7 +8, a0
+	kvm_restore_msa_upper	8,  VCPU_FPR8 +8, a0
+	kvm_restore_msa_upper	9,  VCPU_FPR9 +8, a0
+	kvm_restore_msa_upper	10, VCPU_FPR10+8, a0
+	kvm_restore_msa_upper	11, VCPU_FPR11+8, a0
+	kvm_restore_msa_upper	12, VCPU_FPR12+8, a0
+	kvm_restore_msa_upper	13, VCPU_FPR13+8, a0
+	kvm_restore_msa_upper	14, VCPU_FPR14+8, a0
+	kvm_restore_msa_upper	15, VCPU_FPR15+8, a0
+	kvm_restore_msa_upper	16, VCPU_FPR16+8, a0
+	kvm_restore_msa_upper	17, VCPU_FPR17+8, a0
+	kvm_restore_msa_upper	18, VCPU_FPR18+8, a0
+	kvm_restore_msa_upper	19, VCPU_FPR19+8, a0
+	kvm_restore_msa_upper	20, VCPU_FPR20+8, a0
+	kvm_restore_msa_upper	21, VCPU_FPR21+8, a0
+	kvm_restore_msa_upper	22, VCPU_FPR22+8, a0
+	kvm_restore_msa_upper	23, VCPU_FPR23+8, a0
+	kvm_restore_msa_upper	24, VCPU_FPR24+8, a0
+	kvm_restore_msa_upper	25, VCPU_FPR25+8, a0
+	kvm_restore_msa_upper	26, VCPU_FPR26+8, a0
+	kvm_restore_msa_upper	27, VCPU_FPR27+8, a0
+	kvm_restore_msa_upper	28, VCPU_FPR28+8, a0
+	kvm_restore_msa_upper	29, VCPU_FPR29+8, a0
+	kvm_restore_msa_upper	30, VCPU_FPR30+8, a0
+	kvm_restore_msa_upper	31, VCPU_FPR31+8, a0
+	jr	ra
+	 nop
+	END(__kvm_restore_msa_upper)
+
+LEAF(__kvm_restore_msacsr)
+	lw	t0, VCPU_MSA_CSR(a0)
+	/*
+	 * The ctcmsa must stay at this offset in __kvm_restore_msacsr.
+	 * See kvm_mips_csr_die_notify() which handles t0 containing a value
+	 * which triggers an MSA FP Exception, which must be stepped over and
+	 * ignored since the set cause bits must remain there for the guest.
+	 */
+	_ctcmsa	MSA_CSR, t0
+	jr	ra
+	 nop
+	END(__kvm_restore_msacsr)
diff --git a/arch/mips/kvm/stats.c b/arch/mips/kvm/stats.c
new file mode 100644
index 000000000..3e6682018
--- /dev/null
+++ b/arch/mips/kvm/stats.c
@@ -0,0 +1,63 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * KVM/MIPS: COP0 access histogram
+ *
+ * Copyright (C) 2012  MIPS Technologies, Inc.  All rights reserved.
+ * Authors: Sanjay Lal <sanjayl@kymasys.com>
+ */
+
+#include <linux/kvm_host.h>
+
+char *kvm_cop0_str[N_MIPS_COPROC_REGS] = {
+	"Index",
+	"Random",
+	"EntryLo0",
+	"EntryLo1",
+	"Context",
+	"PG Mask",
+	"Wired",
+	"HWREna",
+	"BadVAddr",
+	"Count",
+	"EntryHI",
+	"Compare",
+	"Status",
+	"Cause",
+	"EXC PC",
+	"PRID",
+	"Config",
+	"LLAddr",
+	"Watch Lo",
+	"Watch Hi",
+	"X Context",
+	"Reserved",
+	"Impl Dep",
+	"Debug",
+	"DEPC",
+	"PerfCnt",
+	"ErrCtl",
+	"CacheErr",
+	"TagLo",
+	"TagHi",
+	"ErrorEPC",
+	"DESAVE"
+};
+
+void kvm_mips_dump_stats(struct kvm_vcpu *vcpu)
+{
+#ifdef CONFIG_KVM_MIPS_DEBUG_COP0_COUNTERS
+	int i, j;
+
+	kvm_info("\nKVM VCPU[%d] COP0 Access Profile:\n", vcpu->vcpu_id);
+	for (i = 0; i < N_MIPS_COPROC_REGS; i++) {
+		for (j = 0; j < N_MIPS_COPROC_SEL; j++) {
+			if (vcpu->arch.cop0.stat[i][j])
+				kvm_info("%s[%d]: %lu\n", kvm_cop0_str[i], j,
+					 vcpu->arch.cop0.stat[i][j]);
+		}
+	}
+#endif
+}
diff --git a/arch/mips/kvm/tlb.c b/arch/mips/kvm/tlb.c
new file mode 100644
index 000000000..4e91971da
--- /dev/null
+++ b/arch/mips/kvm/tlb.c
@@ -0,0 +1,525 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * KVM/MIPS TLB handling, this file is part of the Linux host kernel so that
+ * TLB handlers run from KSEG0
+ *
+ * Copyright (C) 2012  MIPS Technologies, Inc.  All rights reserved.
+ * Authors: Sanjay Lal <sanjayl@kymasys.com>
+ */
+
+#include <linux/sched.h>
+#include <linux/smp.h>
+#include <linux/mm.h>
+#include <linux/delay.h>
+#include <linux/export.h>
+#include <linux/kvm_host.h>
+#include <linux/srcu.h>
+
+#include <asm/cpu.h>
+#include <asm/bootinfo.h>
+#include <asm/mipsregs.h>
+#include <asm/mmu_context.h>
+#include <asm/cacheflush.h>
+#include <asm/tlb.h>
+#include <asm/tlbdebug.h>
+
+#undef CONFIG_MIPS_MT
+#include <asm/r4kcache.h>
+#define CONFIG_MIPS_MT
+
+unsigned long GUESTID_MASK;
+EXPORT_SYMBOL_GPL(GUESTID_MASK);
+unsigned long GUESTID_FIRST_VERSION;
+EXPORT_SYMBOL_GPL(GUESTID_FIRST_VERSION);
+unsigned long GUESTID_VERSION_MASK;
+EXPORT_SYMBOL_GPL(GUESTID_VERSION_MASK);
+
+static u32 kvm_mips_get_root_asid(struct kvm_vcpu *vcpu)
+{
+	struct mm_struct *gpa_mm = &vcpu->kvm->arch.gpa_mm;
+
+	if (cpu_has_guestid)
+		return 0;
+	else
+		return cpu_asid(smp_processor_id(), gpa_mm);
+}
+
+static int _kvm_mips_host_tlb_inv(unsigned long entryhi)
+{
+	int idx;
+
+	write_c0_entryhi(entryhi);
+	mtc0_tlbw_hazard();
+
+	tlb_probe();
+	tlb_probe_hazard();
+	idx = read_c0_index();
+
+	BUG_ON(idx >= current_cpu_data.tlbsize);
+
+	if (idx >= 0) {
+		write_c0_entryhi(UNIQUE_ENTRYHI(idx));
+		write_c0_entrylo0(0);
+		write_c0_entrylo1(0);
+		mtc0_tlbw_hazard();
+
+		tlb_write_indexed();
+		tlbw_use_hazard();
+	}
+
+	return idx;
+}
+
+/* GuestID management */
+
+/**
+ * clear_root_gid() - Set GuestCtl1.RID for normal root operation.
+ */
+static inline void clear_root_gid(void)
+{
+	if (cpu_has_guestid) {
+		clear_c0_guestctl1(MIPS_GCTL1_RID);
+		mtc0_tlbw_hazard();
+	}
+}
+
+/**
+ * set_root_gid_to_guest_gid() - Set GuestCtl1.RID to match GuestCtl1.ID.
+ *
+ * Sets the root GuestID to match the current guest GuestID, for TLB operation
+ * on the GPA->RPA mappings in the root TLB.
+ *
+ * The caller must be sure to disable HTW while the root GID is set, and
+ * possibly longer if TLB registers are modified.
+ */
+static inline void set_root_gid_to_guest_gid(void)
+{
+	unsigned int guestctl1;
+
+	if (cpu_has_guestid) {
+		back_to_back_c0_hazard();
+		guestctl1 = read_c0_guestctl1();
+		guestctl1 = (guestctl1 & ~MIPS_GCTL1_RID) |
+			((guestctl1 & MIPS_GCTL1_ID) >> MIPS_GCTL1_ID_SHIFT)
+						     << MIPS_GCTL1_RID_SHIFT;
+		write_c0_guestctl1(guestctl1);
+		mtc0_tlbw_hazard();
+	}
+}
+
+int kvm_vz_host_tlb_inv(struct kvm_vcpu *vcpu, unsigned long va)
+{
+	int idx;
+	unsigned long flags, old_entryhi;
+
+	local_irq_save(flags);
+	htw_stop();
+
+	/* Set root GuestID for root probe and write of guest TLB entry */
+	set_root_gid_to_guest_gid();
+
+	old_entryhi = read_c0_entryhi();
+
+	idx = _kvm_mips_host_tlb_inv((va & VPN2_MASK) |
+				     kvm_mips_get_root_asid(vcpu));
+
+	write_c0_entryhi(old_entryhi);
+	clear_root_gid();
+	mtc0_tlbw_hazard();
+
+	htw_start();
+	local_irq_restore(flags);
+
+	/*
+	 * We don't want to get reserved instruction exceptions for missing tlb
+	 * entries.
+	 */
+	if (cpu_has_vtag_icache)
+		flush_icache_all();
+
+	if (idx > 0)
+		kvm_debug("%s: Invalidated root entryhi %#lx @ idx %d\n",
+			  __func__, (va & VPN2_MASK) |
+				    kvm_mips_get_root_asid(vcpu), idx);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(kvm_vz_host_tlb_inv);
+
+/**
+ * kvm_vz_guest_tlb_lookup() - Lookup a guest VZ TLB mapping.
+ * @vcpu:	KVM VCPU pointer.
+ * @gpa:	Guest virtual address in a TLB mapped guest segment.
+ * @gpa:	Pointer to output guest physical address it maps to.
+ *
+ * Converts a guest virtual address in a guest TLB mapped segment to a guest
+ * physical address, by probing the guest TLB.
+ *
+ * Returns:	0 if guest TLB mapping exists for @gva. *@gpa will have been
+ *		written.
+ *		-EFAULT if no guest TLB mapping exists for @gva. *@gpa may not
+ *		have been written.
+ */
+int kvm_vz_guest_tlb_lookup(struct kvm_vcpu *vcpu, unsigned long gva,
+			    unsigned long *gpa)
+{
+	unsigned long o_entryhi, o_entrylo[2], o_pagemask;
+	unsigned int o_index;
+	unsigned long entrylo[2], pagemask, pagemaskbit, pa;
+	unsigned long flags;
+	int index;
+
+	/* Probe the guest TLB for a mapping */
+	local_irq_save(flags);
+	/* Set root GuestID for root probe of guest TLB entry */
+	htw_stop();
+	set_root_gid_to_guest_gid();
+
+	o_entryhi = read_gc0_entryhi();
+	o_index = read_gc0_index();
+
+	write_gc0_entryhi((o_entryhi & 0x3ff) | (gva & ~0xfffl));
+	mtc0_tlbw_hazard();
+	guest_tlb_probe();
+	tlb_probe_hazard();
+
+	index = read_gc0_index();
+	if (index < 0) {
+		/* No match, fail */
+		write_gc0_entryhi(o_entryhi);
+		write_gc0_index(o_index);
+
+		clear_root_gid();
+		htw_start();
+		local_irq_restore(flags);
+		return -EFAULT;
+	}
+
+	/* Match! read the TLB entry */
+	o_entrylo[0] = read_gc0_entrylo0();
+	o_entrylo[1] = read_gc0_entrylo1();
+	o_pagemask = read_gc0_pagemask();
+
+	mtc0_tlbr_hazard();
+	guest_tlb_read();
+	tlb_read_hazard();
+
+	entrylo[0] = read_gc0_entrylo0();
+	entrylo[1] = read_gc0_entrylo1();
+	pagemask = ~read_gc0_pagemask() & ~0x1fffl;
+
+	write_gc0_entryhi(o_entryhi);
+	write_gc0_index(o_index);
+	write_gc0_entrylo0(o_entrylo[0]);
+	write_gc0_entrylo1(o_entrylo[1]);
+	write_gc0_pagemask(o_pagemask);
+
+	clear_root_gid();
+	htw_start();
+	local_irq_restore(flags);
+
+	/* Select one of the EntryLo values and interpret the GPA */
+	pagemaskbit = (pagemask ^ (pagemask & (pagemask - 1))) >> 1;
+	pa = entrylo[!!(gva & pagemaskbit)];
+
+	/*
+	 * TLB entry may have become invalid since TLB probe if physical FTLB
+	 * entries are shared between threads (e.g. I6400).
+	 */
+	if (!(pa & ENTRYLO_V))
+		return -EFAULT;
+
+	/*
+	 * Note, this doesn't take guest MIPS32 XPA into account, where PFN is
+	 * split with XI/RI in the middle.
+	 */
+	pa = (pa << 6) & ~0xfffl;
+	pa |= gva & ~(pagemask | pagemaskbit);
+
+	*gpa = pa;
+	return 0;
+}
+EXPORT_SYMBOL_GPL(kvm_vz_guest_tlb_lookup);
+
+/**
+ * kvm_vz_local_flush_roottlb_all_guests() - Flush all root TLB entries for
+ * guests.
+ *
+ * Invalidate all entries in root tlb which are GPA mappings.
+ */
+void kvm_vz_local_flush_roottlb_all_guests(void)
+{
+	unsigned long flags;
+	unsigned long old_entryhi, old_pagemask, old_guestctl1;
+	int entry;
+
+	if (WARN_ON(!cpu_has_guestid))
+		return;
+
+	local_irq_save(flags);
+	htw_stop();
+
+	/* TLBR may clobber EntryHi.ASID, PageMask, and GuestCtl1.RID */
+	old_entryhi = read_c0_entryhi();
+	old_pagemask = read_c0_pagemask();
+	old_guestctl1 = read_c0_guestctl1();
+
+	/*
+	 * Invalidate guest entries in root TLB while leaving root entries
+	 * intact when possible.
+	 */
+	for (entry = 0; entry < current_cpu_data.tlbsize; entry++) {
+		write_c0_index(entry);
+		mtc0_tlbw_hazard();
+		tlb_read();
+		tlb_read_hazard();
+
+		/* Don't invalidate non-guest (RVA) mappings in the root TLB */
+		if (!(read_c0_guestctl1() & MIPS_GCTL1_RID))
+			continue;
+
+		/* Make sure all entries differ. */
+		write_c0_entryhi(UNIQUE_ENTRYHI(entry));
+		write_c0_entrylo0(0);
+		write_c0_entrylo1(0);
+		write_c0_guestctl1(0);
+		mtc0_tlbw_hazard();
+		tlb_write_indexed();
+	}
+
+	write_c0_entryhi(old_entryhi);
+	write_c0_pagemask(old_pagemask);
+	write_c0_guestctl1(old_guestctl1);
+	tlbw_use_hazard();
+
+	htw_start();
+	local_irq_restore(flags);
+}
+EXPORT_SYMBOL_GPL(kvm_vz_local_flush_roottlb_all_guests);
+
+/**
+ * kvm_vz_local_flush_guesttlb_all() - Flush all guest TLB entries.
+ *
+ * Invalidate all entries in guest tlb irrespective of guestid.
+ */
+void kvm_vz_local_flush_guesttlb_all(void)
+{
+	unsigned long flags;
+	unsigned long old_index;
+	unsigned long old_entryhi;
+	unsigned long old_entrylo[2];
+	unsigned long old_pagemask;
+	int entry;
+	u64 cvmmemctl2 = 0;
+
+	local_irq_save(flags);
+
+	/* Preserve all clobbered guest registers */
+	old_index = read_gc0_index();
+	old_entryhi = read_gc0_entryhi();
+	old_entrylo[0] = read_gc0_entrylo0();
+	old_entrylo[1] = read_gc0_entrylo1();
+	old_pagemask = read_gc0_pagemask();
+
+	switch (current_cpu_type()) {
+	case CPU_CAVIUM_OCTEON3:
+		/* Inhibit machine check due to multiple matching TLB entries */
+		cvmmemctl2 = read_c0_cvmmemctl2();
+		cvmmemctl2 |= CVMMEMCTL2_INHIBITTS;
+		write_c0_cvmmemctl2(cvmmemctl2);
+		break;
+	}
+
+	/* Invalidate guest entries in guest TLB */
+	write_gc0_entrylo0(0);
+	write_gc0_entrylo1(0);
+	write_gc0_pagemask(0);
+	for (entry = 0; entry < current_cpu_data.guest.tlbsize; entry++) {
+		/* Make sure all entries differ. */
+		write_gc0_index(entry);
+		write_gc0_entryhi(UNIQUE_GUEST_ENTRYHI(entry));
+		mtc0_tlbw_hazard();
+		guest_tlb_write_indexed();
+	}
+
+	if (cvmmemctl2) {
+		cvmmemctl2 &= ~CVMMEMCTL2_INHIBITTS;
+		write_c0_cvmmemctl2(cvmmemctl2);
+	}
+
+	write_gc0_index(old_index);
+	write_gc0_entryhi(old_entryhi);
+	write_gc0_entrylo0(old_entrylo[0]);
+	write_gc0_entrylo1(old_entrylo[1]);
+	write_gc0_pagemask(old_pagemask);
+	tlbw_use_hazard();
+
+	local_irq_restore(flags);
+}
+EXPORT_SYMBOL_GPL(kvm_vz_local_flush_guesttlb_all);
+
+/**
+ * kvm_vz_save_guesttlb() - Save a range of guest TLB entries.
+ * @buf:	Buffer to write TLB entries into.
+ * @index:	Start index.
+ * @count:	Number of entries to save.
+ *
+ * Save a range of guest TLB entries. The caller must ensure interrupts are
+ * disabled.
+ */
+void kvm_vz_save_guesttlb(struct kvm_mips_tlb *buf, unsigned int index,
+			  unsigned int count)
+{
+	unsigned int end = index + count;
+	unsigned long old_entryhi, old_entrylo0, old_entrylo1, old_pagemask;
+	unsigned int guestctl1 = 0;
+	int old_index, i;
+
+	/* Save registers we're about to clobber */
+	old_index = read_gc0_index();
+	old_entryhi = read_gc0_entryhi();
+	old_entrylo0 = read_gc0_entrylo0();
+	old_entrylo1 = read_gc0_entrylo1();
+	old_pagemask = read_gc0_pagemask();
+
+	/* Set root GuestID for root probe */
+	htw_stop();
+	set_root_gid_to_guest_gid();
+	if (cpu_has_guestid)
+		guestctl1 = read_c0_guestctl1();
+
+	/* Read each entry from guest TLB */
+	for (i = index; i < end; ++i, ++buf) {
+		write_gc0_index(i);
+
+		mtc0_tlbr_hazard();
+		guest_tlb_read();
+		tlb_read_hazard();
+
+		if (cpu_has_guestid &&
+		    (read_c0_guestctl1() ^ guestctl1) & MIPS_GCTL1_RID) {
+			/* Entry invalid or belongs to another guest */
+			buf->tlb_hi = UNIQUE_GUEST_ENTRYHI(i);
+			buf->tlb_lo[0] = 0;
+			buf->tlb_lo[1] = 0;
+			buf->tlb_mask = 0;
+		} else {
+			/* Entry belongs to the right guest */
+			buf->tlb_hi = read_gc0_entryhi();
+			buf->tlb_lo[0] = read_gc0_entrylo0();
+			buf->tlb_lo[1] = read_gc0_entrylo1();
+			buf->tlb_mask = read_gc0_pagemask();
+		}
+	}
+
+	/* Clear root GuestID again */
+	clear_root_gid();
+	htw_start();
+
+	/* Restore clobbered registers */
+	write_gc0_index(old_index);
+	write_gc0_entryhi(old_entryhi);
+	write_gc0_entrylo0(old_entrylo0);
+	write_gc0_entrylo1(old_entrylo1);
+	write_gc0_pagemask(old_pagemask);
+
+	tlbw_use_hazard();
+}
+EXPORT_SYMBOL_GPL(kvm_vz_save_guesttlb);
+
+/**
+ * kvm_vz_load_guesttlb() - Save a range of guest TLB entries.
+ * @buf:	Buffer to read TLB entries from.
+ * @index:	Start index.
+ * @count:	Number of entries to load.
+ *
+ * Load a range of guest TLB entries. The caller must ensure interrupts are
+ * disabled.
+ */
+void kvm_vz_load_guesttlb(const struct kvm_mips_tlb *buf, unsigned int index,
+			  unsigned int count)
+{
+	unsigned int end = index + count;
+	unsigned long old_entryhi, old_entrylo0, old_entrylo1, old_pagemask;
+	int old_index, i;
+
+	/* Save registers we're about to clobber */
+	old_index = read_gc0_index();
+	old_entryhi = read_gc0_entryhi();
+	old_entrylo0 = read_gc0_entrylo0();
+	old_entrylo1 = read_gc0_entrylo1();
+	old_pagemask = read_gc0_pagemask();
+
+	/* Set root GuestID for root probe */
+	htw_stop();
+	set_root_gid_to_guest_gid();
+
+	/* Write each entry to guest TLB */
+	for (i = index; i < end; ++i, ++buf) {
+		write_gc0_index(i);
+		write_gc0_entryhi(buf->tlb_hi);
+		write_gc0_entrylo0(buf->tlb_lo[0]);
+		write_gc0_entrylo1(buf->tlb_lo[1]);
+		write_gc0_pagemask(buf->tlb_mask);
+
+		mtc0_tlbw_hazard();
+		guest_tlb_write_indexed();
+	}
+
+	/* Clear root GuestID again */
+	clear_root_gid();
+	htw_start();
+
+	/* Restore clobbered registers */
+	write_gc0_index(old_index);
+	write_gc0_entryhi(old_entryhi);
+	write_gc0_entrylo0(old_entrylo0);
+	write_gc0_entrylo1(old_entrylo1);
+	write_gc0_pagemask(old_pagemask);
+
+	tlbw_use_hazard();
+}
+EXPORT_SYMBOL_GPL(kvm_vz_load_guesttlb);
+
+#ifdef CONFIG_CPU_LOONGSON64
+void kvm_loongson_clear_guest_vtlb(void)
+{
+	int idx = read_gc0_index();
+
+	/* Set root GuestID for root probe and write of guest TLB entry */
+	set_root_gid_to_guest_gid();
+
+	write_gc0_index(0);
+	guest_tlbinvf();
+	write_gc0_index(idx);
+
+	clear_root_gid();
+	set_c0_diag(LOONGSON_DIAG_ITLB | LOONGSON_DIAG_DTLB);
+}
+EXPORT_SYMBOL_GPL(kvm_loongson_clear_guest_vtlb);
+
+void kvm_loongson_clear_guest_ftlb(void)
+{
+	int i;
+	int idx = read_gc0_index();
+
+	/* Set root GuestID for root probe and write of guest TLB entry */
+	set_root_gid_to_guest_gid();
+
+	for (i = current_cpu_data.tlbsizevtlb;
+	     i < (current_cpu_data.tlbsizevtlb +
+		     current_cpu_data.tlbsizeftlbsets);
+	     i++) {
+		write_gc0_index(i);
+		guest_tlbinvf();
+	}
+	write_gc0_index(idx);
+
+	clear_root_gid();
+	set_c0_diag(LOONGSON_DIAG_ITLB | LOONGSON_DIAG_DTLB);
+}
+EXPORT_SYMBOL_GPL(kvm_loongson_clear_guest_ftlb);
+#endif
diff --git a/arch/mips/kvm/trace.h b/arch/mips/kvm/trace.h
new file mode 100644
index 000000000..136c3535a
--- /dev/null
+++ b/arch/mips/kvm/trace.h
@@ -0,0 +1,346 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2012  MIPS Technologies, Inc.  All rights reserved.
+ * Authors: Sanjay Lal <sanjayl@kymasys.com>
+ */
+
+#if !defined(_TRACE_KVM_H) || defined(TRACE_HEADER_MULTI_READ)
+#define _TRACE_KVM_H
+
+#include <linux/tracepoint.h>
+
+#undef TRACE_SYSTEM
+#define TRACE_SYSTEM kvm
+#define TRACE_INCLUDE_PATH .
+#define TRACE_INCLUDE_FILE trace
+
+/*
+ * arch/mips/kvm/mips.c
+ */
+extern bool kvm_trace_guest_mode_change;
+int kvm_guest_mode_change_trace_reg(void);
+void kvm_guest_mode_change_trace_unreg(void);
+
+/*
+ * Tracepoints for VM enters
+ */
+DECLARE_EVENT_CLASS(kvm_transition,
+	TP_PROTO(struct kvm_vcpu *vcpu),
+	TP_ARGS(vcpu),
+	TP_STRUCT__entry(
+		__field(unsigned long, pc)
+	),
+
+	TP_fast_assign(
+		__entry->pc = vcpu->arch.pc;
+	),
+
+	TP_printk("PC: 0x%08lx",
+		  __entry->pc)
+);
+
+DEFINE_EVENT(kvm_transition, kvm_enter,
+	     TP_PROTO(struct kvm_vcpu *vcpu),
+	     TP_ARGS(vcpu));
+
+DEFINE_EVENT(kvm_transition, kvm_reenter,
+	     TP_PROTO(struct kvm_vcpu *vcpu),
+	     TP_ARGS(vcpu));
+
+DEFINE_EVENT(kvm_transition, kvm_out,
+	     TP_PROTO(struct kvm_vcpu *vcpu),
+	     TP_ARGS(vcpu));
+
+/* The first 32 exit reasons correspond to Cause.ExcCode */
+#define KVM_TRACE_EXIT_INT		 0
+#define KVM_TRACE_EXIT_TLBMOD		 1
+#define KVM_TRACE_EXIT_TLBMISS_LD	 2
+#define KVM_TRACE_EXIT_TLBMISS_ST	 3
+#define KVM_TRACE_EXIT_ADDRERR_LD	 4
+#define KVM_TRACE_EXIT_ADDRERR_ST	 5
+#define KVM_TRACE_EXIT_SYSCALL		 8
+#define KVM_TRACE_EXIT_BREAK_INST	 9
+#define KVM_TRACE_EXIT_RESVD_INST	10
+#define KVM_TRACE_EXIT_COP_UNUSABLE	11
+#define KVM_TRACE_EXIT_TRAP_INST	13
+#define KVM_TRACE_EXIT_MSA_FPE		14
+#define KVM_TRACE_EXIT_FPE		15
+#define KVM_TRACE_EXIT_MSA_DISABLED	21
+#define KVM_TRACE_EXIT_GUEST_EXIT	27
+/* Further exit reasons */
+#define KVM_TRACE_EXIT_WAIT		32
+#define KVM_TRACE_EXIT_CACHE		33
+#define KVM_TRACE_EXIT_SIGNAL		34
+/* 32 exit reasons correspond to GuestCtl0.GExcCode (VZ) */
+#define KVM_TRACE_EXIT_GEXCCODE_BASE	64
+#define KVM_TRACE_EXIT_GPSI		64	/*  0 */
+#define KVM_TRACE_EXIT_GSFC		65	/*  1 */
+#define KVM_TRACE_EXIT_HC		66	/*  2 */
+#define KVM_TRACE_EXIT_GRR		67	/*  3 */
+#define KVM_TRACE_EXIT_GVA		72	/*  8 */
+#define KVM_TRACE_EXIT_GHFC		73	/*  9 */
+#define KVM_TRACE_EXIT_GPA		74	/* 10 */
+
+/* Tracepoints for VM exits */
+#define kvm_trace_symbol_exit_types				\
+	{ KVM_TRACE_EXIT_INT,		"Interrupt" },		\
+	{ KVM_TRACE_EXIT_TLBMOD,	"TLB Mod" },		\
+	{ KVM_TRACE_EXIT_TLBMISS_LD,	"TLB Miss (LD)" },	\
+	{ KVM_TRACE_EXIT_TLBMISS_ST,	"TLB Miss (ST)" },	\
+	{ KVM_TRACE_EXIT_ADDRERR_LD,	"Address Error (LD)" },	\
+	{ KVM_TRACE_EXIT_ADDRERR_ST,	"Address Err (ST)" },	\
+	{ KVM_TRACE_EXIT_SYSCALL,	"System Call" },	\
+	{ KVM_TRACE_EXIT_BREAK_INST,	"Break Inst" },		\
+	{ KVM_TRACE_EXIT_RESVD_INST,	"Reserved Inst" },	\
+	{ KVM_TRACE_EXIT_COP_UNUSABLE,	"COP0/1 Unusable" },	\
+	{ KVM_TRACE_EXIT_TRAP_INST,	"Trap Inst" },		\
+	{ KVM_TRACE_EXIT_MSA_FPE,	"MSA FPE" },		\
+	{ KVM_TRACE_EXIT_FPE,		"FPE" },		\
+	{ KVM_TRACE_EXIT_MSA_DISABLED,	"MSA Disabled" },	\
+	{ KVM_TRACE_EXIT_GUEST_EXIT,	"Guest Exit" },		\
+	{ KVM_TRACE_EXIT_WAIT,		"WAIT" },		\
+	{ KVM_TRACE_EXIT_CACHE,		"CACHE" },		\
+	{ KVM_TRACE_EXIT_SIGNAL,	"Signal" },		\
+	{ KVM_TRACE_EXIT_GPSI,		"GPSI" },		\
+	{ KVM_TRACE_EXIT_GSFC,		"GSFC" },		\
+	{ KVM_TRACE_EXIT_HC,		"HC" },			\
+	{ KVM_TRACE_EXIT_GRR,		"GRR" },		\
+	{ KVM_TRACE_EXIT_GVA,		"GVA" },		\
+	{ KVM_TRACE_EXIT_GHFC,		"GHFC" },		\
+	{ KVM_TRACE_EXIT_GPA,		"GPA" }
+
+TRACE_EVENT(kvm_exit,
+	    TP_PROTO(struct kvm_vcpu *vcpu, unsigned int reason),
+	    TP_ARGS(vcpu, reason),
+	    TP_STRUCT__entry(
+			__field(unsigned long, pc)
+			__field(unsigned int, reason)
+	    ),
+
+	    TP_fast_assign(
+			__entry->pc = vcpu->arch.pc;
+			__entry->reason = reason;
+	    ),
+
+	    TP_printk("[%s]PC: 0x%08lx",
+		      __print_symbolic(__entry->reason,
+				       kvm_trace_symbol_exit_types),
+		      __entry->pc)
+);
+
+#define KVM_TRACE_MFC0		0
+#define KVM_TRACE_MTC0		1
+#define KVM_TRACE_DMFC0		2
+#define KVM_TRACE_DMTC0		3
+#define KVM_TRACE_RDHWR		4
+
+#define KVM_TRACE_HWR_COP0	0
+#define KVM_TRACE_HWR_HWR	1
+
+#define KVM_TRACE_COP0(REG, SEL)	((KVM_TRACE_HWR_COP0 << 8) |	\
+					 ((REG) << 3) | (SEL))
+#define KVM_TRACE_HWR(REG, SEL)		((KVM_TRACE_HWR_HWR  << 8) |	\
+					 ((REG) << 3) | (SEL))
+
+#define kvm_trace_symbol_hwr_ops				\
+	{ KVM_TRACE_MFC0,		"MFC0" },		\
+	{ KVM_TRACE_MTC0,		"MTC0" },		\
+	{ KVM_TRACE_DMFC0,		"DMFC0" },		\
+	{ KVM_TRACE_DMTC0,		"DMTC0" },		\
+	{ KVM_TRACE_RDHWR,		"RDHWR" }
+
+#define kvm_trace_symbol_hwr_cop				\
+	{ KVM_TRACE_HWR_COP0,		"COP0" },		\
+	{ KVM_TRACE_HWR_HWR,		"HWR" }
+
+#define kvm_trace_symbol_hwr_regs				\
+	{ KVM_TRACE_COP0( 0, 0),	"Index" },		\
+	{ KVM_TRACE_COP0( 2, 0),	"EntryLo0" },		\
+	{ KVM_TRACE_COP0( 3, 0),	"EntryLo1" },		\
+	{ KVM_TRACE_COP0( 4, 0),	"Context" },		\
+	{ KVM_TRACE_COP0( 4, 2),	"UserLocal" },		\
+	{ KVM_TRACE_COP0( 5, 0),	"PageMask" },		\
+	{ KVM_TRACE_COP0( 6, 0),	"Wired" },		\
+	{ KVM_TRACE_COP0( 7, 0),	"HWREna" },		\
+	{ KVM_TRACE_COP0( 8, 0),	"BadVAddr" },		\
+	{ KVM_TRACE_COP0( 9, 0),	"Count" },		\
+	{ KVM_TRACE_COP0(10, 0),	"EntryHi" },		\
+	{ KVM_TRACE_COP0(11, 0),	"Compare" },		\
+	{ KVM_TRACE_COP0(12, 0),	"Status" },		\
+	{ KVM_TRACE_COP0(12, 1),	"IntCtl" },		\
+	{ KVM_TRACE_COP0(12, 2),	"SRSCtl" },		\
+	{ KVM_TRACE_COP0(13, 0),	"Cause" },		\
+	{ KVM_TRACE_COP0(14, 0),	"EPC" },		\
+	{ KVM_TRACE_COP0(15, 0),	"PRId" },		\
+	{ KVM_TRACE_COP0(15, 1),	"EBase" },		\
+	{ KVM_TRACE_COP0(16, 0),	"Config" },		\
+	{ KVM_TRACE_COP0(16, 1),	"Config1" },		\
+	{ KVM_TRACE_COP0(16, 2),	"Config2" },		\
+	{ KVM_TRACE_COP0(16, 3),	"Config3" },		\
+	{ KVM_TRACE_COP0(16, 4),	"Config4" },		\
+	{ KVM_TRACE_COP0(16, 5),	"Config5" },		\
+	{ KVM_TRACE_COP0(16, 7),	"Config7" },		\
+	{ KVM_TRACE_COP0(17, 1),	"MAAR" },		\
+	{ KVM_TRACE_COP0(17, 2),	"MAARI" },		\
+	{ KVM_TRACE_COP0(26, 0),	"ECC" },		\
+	{ KVM_TRACE_COP0(30, 0),	"ErrorEPC" },		\
+	{ KVM_TRACE_COP0(31, 2),	"KScratch1" },		\
+	{ KVM_TRACE_COP0(31, 3),	"KScratch2" },		\
+	{ KVM_TRACE_COP0(31, 4),	"KScratch3" },		\
+	{ KVM_TRACE_COP0(31, 5),	"KScratch4" },		\
+	{ KVM_TRACE_COP0(31, 6),	"KScratch5" },		\
+	{ KVM_TRACE_COP0(31, 7),	"KScratch6" },		\
+	{ KVM_TRACE_HWR( 0, 0),		"CPUNum" },		\
+	{ KVM_TRACE_HWR( 1, 0),		"SYNCI_Step" },		\
+	{ KVM_TRACE_HWR( 2, 0),		"CC" },			\
+	{ KVM_TRACE_HWR( 3, 0),		"CCRes" },		\
+	{ KVM_TRACE_HWR(29, 0),		"ULR" }
+
+TRACE_EVENT(kvm_hwr,
+	    TP_PROTO(struct kvm_vcpu *vcpu, unsigned int op, unsigned int reg,
+		     unsigned long val),
+	    TP_ARGS(vcpu, op, reg, val),
+	    TP_STRUCT__entry(
+			__field(unsigned long, val)
+			__field(u16, reg)
+			__field(u8, op)
+	    ),
+
+	    TP_fast_assign(
+			__entry->val = val;
+			__entry->reg = reg;
+			__entry->op = op;
+	    ),
+
+	    TP_printk("%s %s (%s:%u:%u) 0x%08lx",
+		      __print_symbolic(__entry->op,
+				       kvm_trace_symbol_hwr_ops),
+		      __print_symbolic(__entry->reg,
+				       kvm_trace_symbol_hwr_regs),
+		      __print_symbolic(__entry->reg >> 8,
+				       kvm_trace_symbol_hwr_cop),
+		      (__entry->reg >> 3) & 0x1f,
+		      __entry->reg & 0x7,
+		      __entry->val)
+);
+
+#define KVM_TRACE_AUX_RESTORE		0
+#define KVM_TRACE_AUX_SAVE		1
+#define KVM_TRACE_AUX_ENABLE		2
+#define KVM_TRACE_AUX_DISABLE		3
+#define KVM_TRACE_AUX_DISCARD		4
+
+#define KVM_TRACE_AUX_FPU		1
+#define KVM_TRACE_AUX_MSA		2
+#define KVM_TRACE_AUX_FPU_MSA		3
+
+#define kvm_trace_symbol_aux_op		\
+	{ KVM_TRACE_AUX_RESTORE, "restore" },	\
+	{ KVM_TRACE_AUX_SAVE,    "save" },	\
+	{ KVM_TRACE_AUX_ENABLE,  "enable" },	\
+	{ KVM_TRACE_AUX_DISABLE, "disable" },	\
+	{ KVM_TRACE_AUX_DISCARD, "discard" }
+
+#define kvm_trace_symbol_aux_state		\
+	{ KVM_TRACE_AUX_FPU,     "FPU" },	\
+	{ KVM_TRACE_AUX_MSA,     "MSA" },	\
+	{ KVM_TRACE_AUX_FPU_MSA, "FPU & MSA" }
+
+TRACE_EVENT(kvm_aux,
+	    TP_PROTO(struct kvm_vcpu *vcpu, unsigned int op,
+		     unsigned int state),
+	    TP_ARGS(vcpu, op, state),
+	    TP_STRUCT__entry(
+			__field(unsigned long, pc)
+			__field(u8, op)
+			__field(u8, state)
+	    ),
+
+	    TP_fast_assign(
+			__entry->pc = vcpu->arch.pc;
+			__entry->op = op;
+			__entry->state = state;
+	    ),
+
+	    TP_printk("%s %s PC: 0x%08lx",
+		      __print_symbolic(__entry->op,
+				       kvm_trace_symbol_aux_op),
+		      __print_symbolic(__entry->state,
+				       kvm_trace_symbol_aux_state),
+		      __entry->pc)
+);
+
+TRACE_EVENT(kvm_asid_change,
+	    TP_PROTO(struct kvm_vcpu *vcpu, unsigned int old_asid,
+		     unsigned int new_asid),
+	    TP_ARGS(vcpu, old_asid, new_asid),
+	    TP_STRUCT__entry(
+			__field(unsigned long, pc)
+			__field(u8, old_asid)
+			__field(u8, new_asid)
+	    ),
+
+	    TP_fast_assign(
+			__entry->pc = vcpu->arch.pc;
+			__entry->old_asid = old_asid;
+			__entry->new_asid = new_asid;
+	    ),
+
+	    TP_printk("PC: 0x%08lx old: 0x%02x new: 0x%02x",
+		      __entry->pc,
+		      __entry->old_asid,
+		      __entry->new_asid)
+);
+
+TRACE_EVENT(kvm_guestid_change,
+	    TP_PROTO(struct kvm_vcpu *vcpu, unsigned int guestid),
+	    TP_ARGS(vcpu, guestid),
+	    TP_STRUCT__entry(
+			__field(unsigned int, guestid)
+	    ),
+
+	    TP_fast_assign(
+			__entry->guestid = guestid;
+	    ),
+
+	    TP_printk("GuestID: 0x%02x",
+		      __entry->guestid)
+);
+
+TRACE_EVENT_FN(kvm_guest_mode_change,
+	    TP_PROTO(struct kvm_vcpu *vcpu),
+	    TP_ARGS(vcpu),
+	    TP_STRUCT__entry(
+			__field(unsigned long, epc)
+			__field(unsigned long, pc)
+			__field(unsigned long, badvaddr)
+			__field(unsigned int, status)
+			__field(unsigned int, cause)
+	    ),
+
+	    TP_fast_assign(
+			__entry->epc = kvm_read_c0_guest_epc(&vcpu->arch.cop0);
+			__entry->pc = vcpu->arch.pc;
+			__entry->badvaddr = kvm_read_c0_guest_badvaddr(&vcpu->arch.cop0);
+			__entry->status = kvm_read_c0_guest_status(&vcpu->arch.cop0);
+			__entry->cause = kvm_read_c0_guest_cause(&vcpu->arch.cop0);
+	    ),
+
+	    TP_printk("EPC: 0x%08lx PC: 0x%08lx Status: 0x%08x Cause: 0x%08x BadVAddr: 0x%08lx",
+		      __entry->epc,
+		      __entry->pc,
+		      __entry->status,
+		      __entry->cause,
+		      __entry->badvaddr),
+
+	    kvm_guest_mode_change_trace_reg,
+	    kvm_guest_mode_change_trace_unreg
+);
+
+#endif /* _TRACE_KVM_H */
+
+/* This part must be outside protection */
+#include <trace/define_trace.h>
diff --git a/arch/mips/kvm/vz.c b/arch/mips/kvm/vz.c
new file mode 100644
index 000000000..c8f7d793b
--- /dev/null
+++ b/arch/mips/kvm/vz.c
@@ -0,0 +1,3324 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * KVM/MIPS: Support for hardware virtualization extensions
+ *
+ * Copyright (C) 2012  MIPS Technologies, Inc.  All rights reserved.
+ * Authors: Yann Le Du <ledu@kymasys.com>
+ */
+
+#include <linux/errno.h>
+#include <linux/err.h>
+#include <linux/module.h>
+#include <linux/preempt.h>
+#include <linux/vmalloc.h>
+#include <asm/cacheflush.h>
+#include <asm/cacheops.h>
+#include <asm/cmpxchg.h>
+#include <asm/fpu.h>
+#include <asm/hazards.h>
+#include <asm/inst.h>
+#include <asm/mmu_context.h>
+#include <asm/r4kcache.h>
+#include <asm/time.h>
+#include <asm/tlb.h>
+#include <asm/tlbex.h>
+
+#include <linux/kvm_host.h>
+
+#include "interrupt.h"
+#ifdef CONFIG_CPU_LOONGSON64
+#include "loongson_regs.h"
+#endif
+
+#include "trace.h"
+
+/* Pointers to last VCPU loaded on each physical CPU */
+static struct kvm_vcpu *last_vcpu[NR_CPUS];
+/* Pointers to last VCPU executed on each physical CPU */
+static struct kvm_vcpu *last_exec_vcpu[NR_CPUS];
+
+/*
+ * Number of guest VTLB entries to use, so we can catch inconsistency between
+ * CPUs.
+ */
+static unsigned int kvm_vz_guest_vtlb_size;
+
+static inline long kvm_vz_read_gc0_ebase(void)
+{
+	if (sizeof(long) == 8 && cpu_has_ebase_wg)
+		return read_gc0_ebase_64();
+	else
+		return read_gc0_ebase();
+}
+
+static inline void kvm_vz_write_gc0_ebase(long v)
+{
+	/*
+	 * First write with WG=1 to write upper bits, then write again in case
+	 * WG should be left at 0.
+	 * write_gc0_ebase_64() is no longer UNDEFINED since R6.
+	 */
+	if (sizeof(long) == 8 &&
+	    (cpu_has_mips64r6 || cpu_has_ebase_wg)) {
+		write_gc0_ebase_64(v | MIPS_EBASE_WG);
+		write_gc0_ebase_64(v);
+	} else {
+		write_gc0_ebase(v | MIPS_EBASE_WG);
+		write_gc0_ebase(v);
+	}
+}
+
+/*
+ * These Config bits may be writable by the guest:
+ * Config:	[K23, KU] (!TLB), K0
+ * Config1:	(none)
+ * Config2:	[TU, SU] (impl)
+ * Config3:	ISAOnExc
+ * Config4:	FTLBPageSize
+ * Config5:	K, CV, MSAEn, UFE, FRE, SBRI, UFR
+ */
+
+static inline unsigned int kvm_vz_config_guest_wrmask(struct kvm_vcpu *vcpu)
+{
+	return CONF_CM_CMASK;
+}
+
+static inline unsigned int kvm_vz_config1_guest_wrmask(struct kvm_vcpu *vcpu)
+{
+	return 0;
+}
+
+static inline unsigned int kvm_vz_config2_guest_wrmask(struct kvm_vcpu *vcpu)
+{
+	return 0;
+}
+
+static inline unsigned int kvm_vz_config3_guest_wrmask(struct kvm_vcpu *vcpu)
+{
+	return MIPS_CONF3_ISA_OE;
+}
+
+static inline unsigned int kvm_vz_config4_guest_wrmask(struct kvm_vcpu *vcpu)
+{
+	/* no need to be exact */
+	return MIPS_CONF4_VFTLBPAGESIZE;
+}
+
+static inline unsigned int kvm_vz_config5_guest_wrmask(struct kvm_vcpu *vcpu)
+{
+	unsigned int mask = MIPS_CONF5_K | MIPS_CONF5_CV | MIPS_CONF5_SBRI;
+
+	/* Permit MSAEn changes if MSA supported and enabled */
+	if (kvm_mips_guest_has_msa(&vcpu->arch))
+		mask |= MIPS_CONF5_MSAEN;
+
+	/*
+	 * Permit guest FPU mode changes if FPU is enabled and the relevant
+	 * feature exists according to FIR register.
+	 */
+	if (kvm_mips_guest_has_fpu(&vcpu->arch)) {
+		if (cpu_has_ufr)
+			mask |= MIPS_CONF5_UFR;
+		if (cpu_has_fre)
+			mask |= MIPS_CONF5_FRE | MIPS_CONF5_UFE;
+	}
+
+	return mask;
+}
+
+static inline unsigned int kvm_vz_config6_guest_wrmask(struct kvm_vcpu *vcpu)
+{
+	return LOONGSON_CONF6_INTIMER | LOONGSON_CONF6_EXTIMER;
+}
+
+/*
+ * VZ optionally allows these additional Config bits to be written by root:
+ * Config:	M, [MT]
+ * Config1:	M, [MMUSize-1, C2, MD, PC, WR, CA], FP
+ * Config2:	M
+ * Config3:	M, MSAP, [BPG], ULRI, [DSP2P, DSPP], CTXTC, [ITL, LPA, VEIC,
+ *		VInt, SP, CDMM, MT, SM, TL]
+ * Config4:	M, [VTLBSizeExt, MMUSizeExt]
+ * Config5:	MRP
+ */
+
+static inline unsigned int kvm_vz_config_user_wrmask(struct kvm_vcpu *vcpu)
+{
+	return kvm_vz_config_guest_wrmask(vcpu) | MIPS_CONF_M;
+}
+
+static inline unsigned int kvm_vz_config1_user_wrmask(struct kvm_vcpu *vcpu)
+{
+	unsigned int mask = kvm_vz_config1_guest_wrmask(vcpu) | MIPS_CONF_M;
+
+	/* Permit FPU to be present if FPU is supported */
+	if (kvm_mips_guest_can_have_fpu(&vcpu->arch))
+		mask |= MIPS_CONF1_FP;
+
+	return mask;
+}
+
+static inline unsigned int kvm_vz_config2_user_wrmask(struct kvm_vcpu *vcpu)
+{
+	return kvm_vz_config2_guest_wrmask(vcpu) | MIPS_CONF_M;
+}
+
+static inline unsigned int kvm_vz_config3_user_wrmask(struct kvm_vcpu *vcpu)
+{
+	unsigned int mask = kvm_vz_config3_guest_wrmask(vcpu) | MIPS_CONF_M |
+		MIPS_CONF3_ULRI | MIPS_CONF3_CTXTC;
+
+	/* Permit MSA to be present if MSA is supported */
+	if (kvm_mips_guest_can_have_msa(&vcpu->arch))
+		mask |= MIPS_CONF3_MSA;
+
+	return mask;
+}
+
+static inline unsigned int kvm_vz_config4_user_wrmask(struct kvm_vcpu *vcpu)
+{
+	return kvm_vz_config4_guest_wrmask(vcpu) | MIPS_CONF_M;
+}
+
+static inline unsigned int kvm_vz_config5_user_wrmask(struct kvm_vcpu *vcpu)
+{
+	return kvm_vz_config5_guest_wrmask(vcpu) | MIPS_CONF5_MRP;
+}
+
+static inline unsigned int kvm_vz_config6_user_wrmask(struct kvm_vcpu *vcpu)
+{
+	return kvm_vz_config6_guest_wrmask(vcpu) |
+		LOONGSON_CONF6_SFBEN | LOONGSON_CONF6_FTLBDIS;
+}
+
+static gpa_t kvm_vz_gva_to_gpa_cb(gva_t gva)
+{
+	/* VZ guest has already converted gva to gpa */
+	return gva;
+}
+
+static void kvm_vz_queue_irq(struct kvm_vcpu *vcpu, unsigned int priority)
+{
+	set_bit(priority, &vcpu->arch.pending_exceptions);
+	clear_bit(priority, &vcpu->arch.pending_exceptions_clr);
+}
+
+static void kvm_vz_dequeue_irq(struct kvm_vcpu *vcpu, unsigned int priority)
+{
+	clear_bit(priority, &vcpu->arch.pending_exceptions);
+	set_bit(priority, &vcpu->arch.pending_exceptions_clr);
+}
+
+static void kvm_vz_queue_timer_int_cb(struct kvm_vcpu *vcpu)
+{
+	/*
+	 * timer expiry is asynchronous to vcpu execution therefore defer guest
+	 * cp0 accesses
+	 */
+	kvm_vz_queue_irq(vcpu, MIPS_EXC_INT_TIMER);
+}
+
+static void kvm_vz_dequeue_timer_int_cb(struct kvm_vcpu *vcpu)
+{
+	/*
+	 * timer expiry is asynchronous to vcpu execution therefore defer guest
+	 * cp0 accesses
+	 */
+	kvm_vz_dequeue_irq(vcpu, MIPS_EXC_INT_TIMER);
+}
+
+static void kvm_vz_queue_io_int_cb(struct kvm_vcpu *vcpu,
+				   struct kvm_mips_interrupt *irq)
+{
+	int intr = (int)irq->irq;
+
+	/*
+	 * interrupts are asynchronous to vcpu execution therefore defer guest
+	 * cp0 accesses
+	 */
+	kvm_vz_queue_irq(vcpu, kvm_irq_to_priority(intr));
+}
+
+static void kvm_vz_dequeue_io_int_cb(struct kvm_vcpu *vcpu,
+				     struct kvm_mips_interrupt *irq)
+{
+	int intr = (int)irq->irq;
+
+	/*
+	 * interrupts are asynchronous to vcpu execution therefore defer guest
+	 * cp0 accesses
+	 */
+	kvm_vz_dequeue_irq(vcpu, kvm_irq_to_priority(-intr));
+}
+
+static int kvm_vz_irq_deliver_cb(struct kvm_vcpu *vcpu, unsigned int priority,
+				 u32 cause)
+{
+	u32 irq = (priority < MIPS_EXC_MAX) ?
+		kvm_priority_to_irq[priority] : 0;
+
+	switch (priority) {
+	case MIPS_EXC_INT_TIMER:
+		set_gc0_cause(C_TI);
+		break;
+
+	case MIPS_EXC_INT_IO_1:
+	case MIPS_EXC_INT_IO_2:
+	case MIPS_EXC_INT_IPI_1:
+	case MIPS_EXC_INT_IPI_2:
+		if (cpu_has_guestctl2)
+			set_c0_guestctl2(irq);
+		else
+			set_gc0_cause(irq);
+		break;
+
+	default:
+		break;
+	}
+
+	clear_bit(priority, &vcpu->arch.pending_exceptions);
+	return 1;
+}
+
+static int kvm_vz_irq_clear_cb(struct kvm_vcpu *vcpu, unsigned int priority,
+			       u32 cause)
+{
+	u32 irq = (priority < MIPS_EXC_MAX) ?
+		kvm_priority_to_irq[priority] : 0;
+
+	switch (priority) {
+	case MIPS_EXC_INT_TIMER:
+		/*
+		 * Explicitly clear irq associated with Cause.IP[IPTI]
+		 * if GuestCtl2 virtual interrupt register not
+		 * supported or if not using GuestCtl2 Hardware Clear.
+		 */
+		if (cpu_has_guestctl2) {
+			if (!(read_c0_guestctl2() & (irq << 14)))
+				clear_c0_guestctl2(irq);
+		} else {
+			clear_gc0_cause(irq);
+		}
+		break;
+
+	case MIPS_EXC_INT_IO_1:
+	case MIPS_EXC_INT_IO_2:
+	case MIPS_EXC_INT_IPI_1:
+	case MIPS_EXC_INT_IPI_2:
+		/* Clear GuestCtl2.VIP irq if not using Hardware Clear */
+		if (cpu_has_guestctl2) {
+			if (!(read_c0_guestctl2() & (irq << 14)))
+				clear_c0_guestctl2(irq);
+		} else {
+			clear_gc0_cause(irq);
+		}
+		break;
+
+	default:
+		break;
+	}
+
+	clear_bit(priority, &vcpu->arch.pending_exceptions_clr);
+	return 1;
+}
+
+/*
+ * VZ guest timer handling.
+ */
+
+/**
+ * kvm_vz_should_use_htimer() - Find whether to use the VZ hard guest timer.
+ * @vcpu:	Virtual CPU.
+ *
+ * Returns:	true if the VZ GTOffset & real guest CP0_Count should be used
+ *		instead of software emulation of guest timer.
+ *		false otherwise.
+ */
+static bool kvm_vz_should_use_htimer(struct kvm_vcpu *vcpu)
+{
+	if (kvm_mips_count_disabled(vcpu))
+		return false;
+
+	/* Chosen frequency must match real frequency */
+	if (mips_hpt_frequency != vcpu->arch.count_hz)
+		return false;
+
+	/* We don't support a CP0_GTOffset with fewer bits than CP0_Count */
+	if (current_cpu_data.gtoffset_mask != 0xffffffff)
+		return false;
+
+	return true;
+}
+
+/**
+ * _kvm_vz_restore_stimer() - Restore soft timer state.
+ * @vcpu:	Virtual CPU.
+ * @compare:	CP0_Compare register value, restored by caller.
+ * @cause:	CP0_Cause register to restore.
+ *
+ * Restore VZ state relating to the soft timer. The hard timer can be enabled
+ * later.
+ */
+static void _kvm_vz_restore_stimer(struct kvm_vcpu *vcpu, u32 compare,
+				   u32 cause)
+{
+	/*
+	 * Avoid spurious counter interrupts by setting Guest CP0_Count to just
+	 * after Guest CP0_Compare.
+	 */
+	write_c0_gtoffset(compare - read_c0_count());
+
+	back_to_back_c0_hazard();
+	write_gc0_cause(cause);
+}
+
+/**
+ * _kvm_vz_restore_htimer() - Restore hard timer state.
+ * @vcpu:	Virtual CPU.
+ * @compare:	CP0_Compare register value, restored by caller.
+ * @cause:	CP0_Cause register to restore.
+ *
+ * Restore hard timer Guest.Count & Guest.Cause taking care to preserve the
+ * value of Guest.CP0_Cause.TI while restoring Guest.CP0_Cause.
+ */
+static void _kvm_vz_restore_htimer(struct kvm_vcpu *vcpu,
+				   u32 compare, u32 cause)
+{
+	u32 start_count, after_count;
+	unsigned long flags;
+
+	/*
+	 * Freeze the soft-timer and sync the guest CP0_Count with it. We do
+	 * this with interrupts disabled to avoid latency.
+	 */
+	local_irq_save(flags);
+	kvm_mips_freeze_hrtimer(vcpu, &start_count);
+	write_c0_gtoffset(start_count - read_c0_count());
+	local_irq_restore(flags);
+
+	/* restore guest CP0_Cause, as TI may already be set */
+	back_to_back_c0_hazard();
+	write_gc0_cause(cause);
+
+	/*
+	 * The above sequence isn't atomic and would result in lost timer
+	 * interrupts if we're not careful. Detect if a timer interrupt is due
+	 * and assert it.
+	 */
+	back_to_back_c0_hazard();
+	after_count = read_gc0_count();
+	if (after_count - start_count > compare - start_count - 1)
+		kvm_vz_queue_irq(vcpu, MIPS_EXC_INT_TIMER);
+}
+
+/**
+ * kvm_vz_restore_timer() - Restore timer state.
+ * @vcpu:	Virtual CPU.
+ *
+ * Restore soft timer state from saved context.
+ */
+static void kvm_vz_restore_timer(struct kvm_vcpu *vcpu)
+{
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
+	u32 cause, compare;
+
+	compare = kvm_read_sw_gc0_compare(cop0);
+	cause = kvm_read_sw_gc0_cause(cop0);
+
+	write_gc0_compare(compare);
+	_kvm_vz_restore_stimer(vcpu, compare, cause);
+}
+
+/**
+ * kvm_vz_acquire_htimer() - Switch to hard timer state.
+ * @vcpu:	Virtual CPU.
+ *
+ * Restore hard timer state on top of existing soft timer state if possible.
+ *
+ * Since hard timer won't remain active over preemption, preemption should be
+ * disabled by the caller.
+ */
+void kvm_vz_acquire_htimer(struct kvm_vcpu *vcpu)
+{
+	u32 gctl0;
+
+	gctl0 = read_c0_guestctl0();
+	if (!(gctl0 & MIPS_GCTL0_GT) && kvm_vz_should_use_htimer(vcpu)) {
+		/* enable guest access to hard timer */
+		write_c0_guestctl0(gctl0 | MIPS_GCTL0_GT);
+
+		_kvm_vz_restore_htimer(vcpu, read_gc0_compare(),
+				       read_gc0_cause());
+	}
+}
+
+/**
+ * _kvm_vz_save_htimer() - Switch to software emulation of guest timer.
+ * @vcpu:	Virtual CPU.
+ * @out_compare: Pointer to write compare value to.
+ * @out_cause:	Pointer to write cause value to.
+ *
+ * Save VZ guest timer state and switch to software emulation of guest CP0
+ * timer. The hard timer must already be in use, so preemption should be
+ * disabled.
+ */
+static void _kvm_vz_save_htimer(struct kvm_vcpu *vcpu,
+				u32 *out_compare, u32 *out_cause)
+{
+	u32 cause, compare, before_count, end_count;
+	ktime_t before_time;
+
+	compare = read_gc0_compare();
+	*out_compare = compare;
+
+	before_time = ktime_get();
+
+	/*
+	 * Record the CP0_Count *prior* to saving CP0_Cause, so we have a time
+	 * at which no pending timer interrupt is missing.
+	 */
+	before_count = read_gc0_count();
+	back_to_back_c0_hazard();
+	cause = read_gc0_cause();
+	*out_cause = cause;
+
+	/*
+	 * Record a final CP0_Count which we will transfer to the soft-timer.
+	 * This is recorded *after* saving CP0_Cause, so we don't get any timer
+	 * interrupts from just after the final CP0_Count point.
+	 */
+	back_to_back_c0_hazard();
+	end_count = read_gc0_count();
+
+	/*
+	 * The above sequence isn't atomic, so we could miss a timer interrupt
+	 * between reading CP0_Cause and end_count. Detect and record any timer
+	 * interrupt due between before_count and end_count.
+	 */
+	if (end_count - before_count > compare - before_count - 1)
+		kvm_vz_queue_irq(vcpu, MIPS_EXC_INT_TIMER);
+
+	/*
+	 * Restore soft-timer, ignoring a small amount of negative drift due to
+	 * delay between freeze_hrtimer and setting CP0_GTOffset.
+	 */
+	kvm_mips_restore_hrtimer(vcpu, before_time, end_count, -0x10000);
+}
+
+/**
+ * kvm_vz_save_timer() - Save guest timer state.
+ * @vcpu:	Virtual CPU.
+ *
+ * Save VZ guest timer state and switch to soft guest timer if hard timer was in
+ * use.
+ */
+static void kvm_vz_save_timer(struct kvm_vcpu *vcpu)
+{
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
+	u32 gctl0, compare, cause;
+
+	gctl0 = read_c0_guestctl0();
+	if (gctl0 & MIPS_GCTL0_GT) {
+		/* disable guest use of hard timer */
+		write_c0_guestctl0(gctl0 & ~MIPS_GCTL0_GT);
+
+		/* save hard timer state */
+		_kvm_vz_save_htimer(vcpu, &compare, &cause);
+	} else {
+		compare = read_gc0_compare();
+		cause = read_gc0_cause();
+	}
+
+	/* save timer-related state to VCPU context */
+	kvm_write_sw_gc0_cause(cop0, cause);
+	kvm_write_sw_gc0_compare(cop0, compare);
+}
+
+/**
+ * kvm_vz_lose_htimer() - Ensure hard guest timer is not in use.
+ * @vcpu:	Virtual CPU.
+ *
+ * Transfers the state of the hard guest timer to the soft guest timer, leaving
+ * guest state intact so it can continue to be used with the soft timer.
+ */
+void kvm_vz_lose_htimer(struct kvm_vcpu *vcpu)
+{
+	u32 gctl0, compare, cause;
+
+	preempt_disable();
+	gctl0 = read_c0_guestctl0();
+	if (gctl0 & MIPS_GCTL0_GT) {
+		/* disable guest use of timer */
+		write_c0_guestctl0(gctl0 & ~MIPS_GCTL0_GT);
+
+		/* switch to soft timer */
+		_kvm_vz_save_htimer(vcpu, &compare, &cause);
+
+		/* leave soft timer in usable state */
+		_kvm_vz_restore_stimer(vcpu, compare, cause);
+	}
+	preempt_enable();
+}
+
+/**
+ * is_eva_access() - Find whether an instruction is an EVA memory accessor.
+ * @inst:	32-bit instruction encoding.
+ *
+ * Finds whether @inst encodes an EVA memory access instruction, which would
+ * indicate that emulation of it should access the user mode address space
+ * instead of the kernel mode address space. This matters for MUSUK segments
+ * which are TLB mapped for user mode but unmapped for kernel mode.
+ *
+ * Returns:	Whether @inst encodes an EVA accessor instruction.
+ */
+static bool is_eva_access(union mips_instruction inst)
+{
+	if (inst.spec3_format.opcode != spec3_op)
+		return false;
+
+	switch (inst.spec3_format.func) {
+	case lwle_op:
+	case lwre_op:
+	case cachee_op:
+	case sbe_op:
+	case she_op:
+	case sce_op:
+	case swe_op:
+	case swle_op:
+	case swre_op:
+	case prefe_op:
+	case lbue_op:
+	case lhue_op:
+	case lbe_op:
+	case lhe_op:
+	case lle_op:
+	case lwe_op:
+		return true;
+	default:
+		return false;
+	}
+}
+
+/**
+ * is_eva_am_mapped() - Find whether an access mode is mapped.
+ * @vcpu:	KVM VCPU state.
+ * @am:		3-bit encoded access mode.
+ * @eu:		Segment becomes unmapped and uncached when Status.ERL=1.
+ *
+ * Decode @am to find whether it encodes a mapped segment for the current VCPU
+ * state. Where necessary @eu and the actual instruction causing the fault are
+ * taken into account to make the decision.
+ *
+ * Returns:	Whether the VCPU faulted on a TLB mapped address.
+ */
+static bool is_eva_am_mapped(struct kvm_vcpu *vcpu, unsigned int am, bool eu)
+{
+	u32 am_lookup;
+	int err;
+
+	/*
+	 * Interpret access control mode. We assume address errors will already
+	 * have been caught by the guest, leaving us with:
+	 *      AM      UM  SM  KM  31..24 23..16
+	 * UK    0 000          Unm   0      0
+	 * MK    1 001          TLB   1
+	 * MSK   2 010      TLB TLB   1
+	 * MUSK  3 011  TLB TLB TLB   1
+	 * MUSUK 4 100  TLB TLB Unm   0      1
+	 * USK   5 101      Unm Unm   0      0
+	 * -     6 110                0      0
+	 * UUSK  7 111  Unm Unm Unm   0      0
+	 *
+	 * We shift a magic value by AM across the sign bit to find if always
+	 * TLB mapped, and if not shift by 8 again to find if it depends on KM.
+	 */
+	am_lookup = 0x70080000 << am;
+	if ((s32)am_lookup < 0) {
+		/*
+		 * MK, MSK, MUSK
+		 * Always TLB mapped, unless SegCtl.EU && ERL
+		 */
+		if (!eu || !(read_gc0_status() & ST0_ERL))
+			return true;
+	} else {
+		am_lookup <<= 8;
+		if ((s32)am_lookup < 0) {
+			union mips_instruction inst;
+			unsigned int status;
+			u32 *opc;
+
+			/*
+			 * MUSUK
+			 * TLB mapped if not in kernel mode
+			 */
+			status = read_gc0_status();
+			if (!(status & (ST0_EXL | ST0_ERL)) &&
+			    (status & ST0_KSU))
+				return true;
+			/*
+			 * EVA access instructions in kernel
+			 * mode access user address space.
+			 */
+			opc = (u32 *)vcpu->arch.pc;
+			if (vcpu->arch.host_cp0_cause & CAUSEF_BD)
+				opc += 1;
+			err = kvm_get_badinstr(opc, vcpu, &inst.word);
+			if (!err && is_eva_access(inst))
+				return true;
+		}
+	}
+
+	return false;
+}
+
+/**
+ * kvm_vz_gva_to_gpa() - Convert valid GVA to GPA.
+ * @vcpu:	KVM VCPU state.
+ * @gva:	Guest virtual address to convert.
+ * @gpa:	Output guest physical address.
+ *
+ * Convert a guest virtual address (GVA) which is valid according to the guest
+ * context, to a guest physical address (GPA).
+ *
+ * Returns:	0 on success.
+ *		-errno on failure.
+ */
+static int kvm_vz_gva_to_gpa(struct kvm_vcpu *vcpu, unsigned long gva,
+			     unsigned long *gpa)
+{
+	u32 gva32 = gva;
+	unsigned long segctl;
+
+	if ((long)gva == (s32)gva32) {
+		/* Handle canonical 32-bit virtual address */
+		if (cpu_guest_has_segments) {
+			unsigned long mask, pa;
+
+			switch (gva32 >> 29) {
+			case 0:
+			case 1: /* CFG5 (1GB) */
+				segctl = read_gc0_segctl2() >> 16;
+				mask = (unsigned long)0xfc0000000ull;
+				break;
+			case 2:
+			case 3: /* CFG4 (1GB) */
+				segctl = read_gc0_segctl2();
+				mask = (unsigned long)0xfc0000000ull;
+				break;
+			case 4: /* CFG3 (512MB) */
+				segctl = read_gc0_segctl1() >> 16;
+				mask = (unsigned long)0xfe0000000ull;
+				break;
+			case 5: /* CFG2 (512MB) */
+				segctl = read_gc0_segctl1();
+				mask = (unsigned long)0xfe0000000ull;
+				break;
+			case 6: /* CFG1 (512MB) */
+				segctl = read_gc0_segctl0() >> 16;
+				mask = (unsigned long)0xfe0000000ull;
+				break;
+			case 7: /* CFG0 (512MB) */
+				segctl = read_gc0_segctl0();
+				mask = (unsigned long)0xfe0000000ull;
+				break;
+			default:
+				/*
+				 * GCC 4.9 isn't smart enough to figure out that
+				 * segctl and mask are always initialised.
+				 */
+				unreachable();
+			}
+
+			if (is_eva_am_mapped(vcpu, (segctl >> 4) & 0x7,
+					     segctl & 0x0008))
+				goto tlb_mapped;
+
+			/* Unmapped, find guest physical address */
+			pa = (segctl << 20) & mask;
+			pa |= gva32 & ~mask;
+			*gpa = pa;
+			return 0;
+		} else if ((s32)gva32 < (s32)0xc0000000) {
+			/* legacy unmapped KSeg0 or KSeg1 */
+			*gpa = gva32 & 0x1fffffff;
+			return 0;
+		}
+#ifdef CONFIG_64BIT
+	} else if ((gva & 0xc000000000000000) == 0x8000000000000000) {
+		/* XKPHYS */
+		if (cpu_guest_has_segments) {
+			/*
+			 * Each of the 8 regions can be overridden by SegCtl2.XR
+			 * to use SegCtl1.XAM.
+			 */
+			segctl = read_gc0_segctl2();
+			if (segctl & (1ull << (56 + ((gva >> 59) & 0x7)))) {
+				segctl = read_gc0_segctl1();
+				if (is_eva_am_mapped(vcpu, (segctl >> 59) & 0x7,
+						     0))
+					goto tlb_mapped;
+			}
+
+		}
+		/*
+		 * Traditionally fully unmapped.
+		 * Bits 61:59 specify the CCA, which we can just mask off here.
+		 * Bits 58:PABITS should be zero, but we shouldn't have got here
+		 * if it wasn't.
+		 */
+		*gpa = gva & 0x07ffffffffffffff;
+		return 0;
+#endif
+	}
+
+tlb_mapped:
+	return kvm_vz_guest_tlb_lookup(vcpu, gva, gpa);
+}
+
+/**
+ * kvm_vz_badvaddr_to_gpa() - Convert GVA BadVAddr from root exception to GPA.
+ * @vcpu:	KVM VCPU state.
+ * @badvaddr:	Root BadVAddr.
+ * @gpa:	Output guest physical address.
+ *
+ * VZ implementations are permitted to report guest virtual addresses (GVA) in
+ * BadVAddr on a root exception during guest execution, instead of the more
+ * convenient guest physical addresses (GPA). When we get a GVA, this function
+ * converts it to a GPA, taking into account guest segmentation and guest TLB
+ * state.
+ *
+ * Returns:	0 on success.
+ *		-errno on failure.
+ */
+static int kvm_vz_badvaddr_to_gpa(struct kvm_vcpu *vcpu, unsigned long badvaddr,
+				  unsigned long *gpa)
+{
+	unsigned int gexccode = (vcpu->arch.host_cp0_guestctl0 &
+				 MIPS_GCTL0_GEXC) >> MIPS_GCTL0_GEXC_SHIFT;
+
+	/* If BadVAddr is GPA, then all is well in the world */
+	if (likely(gexccode == MIPS_GCTL0_GEXC_GPA)) {
+		*gpa = badvaddr;
+		return 0;
+	}
+
+	/* Otherwise we'd expect it to be GVA ... */
+	if (WARN(gexccode != MIPS_GCTL0_GEXC_GVA,
+		 "Unexpected gexccode %#x\n", gexccode))
+		return -EINVAL;
+
+	/* ... and we need to perform the GVA->GPA translation in software */
+	return kvm_vz_gva_to_gpa(vcpu, badvaddr, gpa);
+}
+
+static int kvm_trap_vz_no_handler(struct kvm_vcpu *vcpu)
+{
+	u32 *opc = (u32 *) vcpu->arch.pc;
+	u32 cause = vcpu->arch.host_cp0_cause;
+	u32 exccode = (cause & CAUSEF_EXCCODE) >> CAUSEB_EXCCODE;
+	unsigned long badvaddr = vcpu->arch.host_cp0_badvaddr;
+	u32 inst = 0;
+
+	/*
+	 *  Fetch the instruction.
+	 */
+	if (cause & CAUSEF_BD)
+		opc += 1;
+	kvm_get_badinstr(opc, vcpu, &inst);
+
+	kvm_err("Exception Code: %d not handled @ PC: %p, inst: 0x%08x BadVaddr: %#lx Status: %#x\n",
+		exccode, opc, inst, badvaddr,
+		read_gc0_status());
+	kvm_arch_vcpu_dump_regs(vcpu);
+	vcpu->run->exit_reason = KVM_EXIT_INTERNAL_ERROR;
+	return RESUME_HOST;
+}
+
+static unsigned long mips_process_maar(unsigned int op, unsigned long val)
+{
+	/* Mask off unused bits */
+	unsigned long mask = 0xfffff000 | MIPS_MAAR_S | MIPS_MAAR_VL;
+
+	if (read_gc0_pagegrain() & PG_ELPA)
+		mask |= 0x00ffffff00000000ull;
+	if (cpu_guest_has_mvh)
+		mask |= MIPS_MAAR_VH;
+
+	/* Set or clear VH */
+	if (op == mtc_op) {
+		/* clear VH */
+		val &= ~MIPS_MAAR_VH;
+	} else if (op == dmtc_op) {
+		/* set VH to match VL */
+		val &= ~MIPS_MAAR_VH;
+		if (val & MIPS_MAAR_VL)
+			val |= MIPS_MAAR_VH;
+	}
+
+	return val & mask;
+}
+
+static void kvm_write_maari(struct kvm_vcpu *vcpu, unsigned long val)
+{
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
+
+	val &= MIPS_MAARI_INDEX;
+	if (val == MIPS_MAARI_INDEX)
+		kvm_write_sw_gc0_maari(cop0, ARRAY_SIZE(vcpu->arch.maar) - 1);
+	else if (val < ARRAY_SIZE(vcpu->arch.maar))
+		kvm_write_sw_gc0_maari(cop0, val);
+}
+
+static enum emulation_result kvm_vz_gpsi_cop0(union mips_instruction inst,
+					      u32 *opc, u32 cause,
+					      struct kvm_vcpu *vcpu)
+{
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
+	enum emulation_result er = EMULATE_DONE;
+	u32 rt, rd, sel;
+	unsigned long curr_pc;
+	unsigned long val;
+
+	/*
+	 * Update PC and hold onto current PC in case there is
+	 * an error and we want to rollback the PC
+	 */
+	curr_pc = vcpu->arch.pc;
+	er = update_pc(vcpu, cause);
+	if (er == EMULATE_FAIL)
+		return er;
+
+	if (inst.co_format.co) {
+		switch (inst.co_format.func) {
+		case wait_op:
+			er = kvm_mips_emul_wait(vcpu);
+			break;
+		default:
+			er = EMULATE_FAIL;
+		}
+	} else {
+		rt = inst.c0r_format.rt;
+		rd = inst.c0r_format.rd;
+		sel = inst.c0r_format.sel;
+
+		switch (inst.c0r_format.rs) {
+		case dmfc_op:
+		case mfc_op:
+#ifdef CONFIG_KVM_MIPS_DEBUG_COP0_COUNTERS
+			cop0->stat[rd][sel]++;
+#endif
+			if (rd == MIPS_CP0_COUNT &&
+			    sel == 0) {			/* Count */
+				val = kvm_mips_read_count(vcpu);
+			} else if (rd == MIPS_CP0_COMPARE &&
+				   sel == 0) {		/* Compare */
+				val = read_gc0_compare();
+			} else if (rd == MIPS_CP0_LLADDR &&
+				   sel == 0) {		/* LLAddr */
+				if (cpu_guest_has_rw_llb)
+					val = read_gc0_lladdr() &
+						MIPS_LLADDR_LLB;
+				else
+					val = 0;
+			} else if (rd == MIPS_CP0_LLADDR &&
+				   sel == 1 &&		/* MAAR */
+				   cpu_guest_has_maar &&
+				   !cpu_guest_has_dyn_maar) {
+				/* MAARI must be in range */
+				BUG_ON(kvm_read_sw_gc0_maari(cop0) >=
+						ARRAY_SIZE(vcpu->arch.maar));
+				val = vcpu->arch.maar[
+					kvm_read_sw_gc0_maari(cop0)];
+			} else if ((rd == MIPS_CP0_PRID &&
+				    (sel == 0 ||	/* PRid */
+				     sel == 2 ||	/* CDMMBase */
+				     sel == 3)) ||	/* CMGCRBase */
+				   (rd == MIPS_CP0_STATUS &&
+				    (sel == 2 ||	/* SRSCtl */
+				     sel == 3)) ||	/* SRSMap */
+				   (rd == MIPS_CP0_CONFIG &&
+				    (sel == 6 ||	/* Config6 */
+				     sel == 7)) ||	/* Config7 */
+				   (rd == MIPS_CP0_LLADDR &&
+				    (sel == 2) &&	/* MAARI */
+				    cpu_guest_has_maar &&
+				    !cpu_guest_has_dyn_maar) ||
+				   (rd == MIPS_CP0_ERRCTL &&
+				    (sel == 0))) {	/* ErrCtl */
+				val = cop0->reg[rd][sel];
+#ifdef CONFIG_CPU_LOONGSON64
+			} else if (rd == MIPS_CP0_DIAG &&
+				   (sel == 0)) {	/* Diag */
+				val = cop0->reg[rd][sel];
+#endif
+			} else {
+				val = 0;
+				er = EMULATE_FAIL;
+			}
+
+			if (er != EMULATE_FAIL) {
+				/* Sign extend */
+				if (inst.c0r_format.rs == mfc_op)
+					val = (int)val;
+				vcpu->arch.gprs[rt] = val;
+			}
+
+			trace_kvm_hwr(vcpu, (inst.c0r_format.rs == mfc_op) ?
+					KVM_TRACE_MFC0 : KVM_TRACE_DMFC0,
+				      KVM_TRACE_COP0(rd, sel), val);
+			break;
+
+		case dmtc_op:
+		case mtc_op:
+#ifdef CONFIG_KVM_MIPS_DEBUG_COP0_COUNTERS
+			cop0->stat[rd][sel]++;
+#endif
+			val = vcpu->arch.gprs[rt];
+			trace_kvm_hwr(vcpu, (inst.c0r_format.rs == mtc_op) ?
+					KVM_TRACE_MTC0 : KVM_TRACE_DMTC0,
+				      KVM_TRACE_COP0(rd, sel), val);
+
+			if (rd == MIPS_CP0_COUNT &&
+			    sel == 0) {			/* Count */
+				kvm_vz_lose_htimer(vcpu);
+				kvm_mips_write_count(vcpu, vcpu->arch.gprs[rt]);
+			} else if (rd == MIPS_CP0_COMPARE &&
+				   sel == 0) {		/* Compare */
+				kvm_mips_write_compare(vcpu,
+						       vcpu->arch.gprs[rt],
+						       true);
+			} else if (rd == MIPS_CP0_LLADDR &&
+				   sel == 0) {		/* LLAddr */
+				/*
+				 * P5600 generates GPSI on guest MTC0 LLAddr.
+				 * Only allow the guest to clear LLB.
+				 */
+				if (cpu_guest_has_rw_llb &&
+				    !(val & MIPS_LLADDR_LLB))
+					write_gc0_lladdr(0);
+			} else if (rd == MIPS_CP0_LLADDR &&
+				   sel == 1 &&		/* MAAR */
+				   cpu_guest_has_maar &&
+				   !cpu_guest_has_dyn_maar) {
+				val = mips_process_maar(inst.c0r_format.rs,
+							val);
+
+				/* MAARI must be in range */
+				BUG_ON(kvm_read_sw_gc0_maari(cop0) >=
+						ARRAY_SIZE(vcpu->arch.maar));
+				vcpu->arch.maar[kvm_read_sw_gc0_maari(cop0)] =
+									val;
+			} else if (rd == MIPS_CP0_LLADDR &&
+				   (sel == 2) &&	/* MAARI */
+				   cpu_guest_has_maar &&
+				   !cpu_guest_has_dyn_maar) {
+				kvm_write_maari(vcpu, val);
+			} else if (rd == MIPS_CP0_CONFIG &&
+				   (sel == 6)) {
+				cop0->reg[rd][sel] = (int)val;
+			} else if (rd == MIPS_CP0_ERRCTL &&
+				   (sel == 0)) {	/* ErrCtl */
+				/* ignore the written value */
+#ifdef CONFIG_CPU_LOONGSON64
+			} else if (rd == MIPS_CP0_DIAG &&
+				   (sel == 0)) {	/* Diag */
+				unsigned long flags;
+
+				local_irq_save(flags);
+				if (val & LOONGSON_DIAG_BTB) {
+					/* Flush BTB */
+					set_c0_diag(LOONGSON_DIAG_BTB);
+				}
+				if (val & LOONGSON_DIAG_ITLB) {
+					/* Flush ITLB */
+					set_c0_diag(LOONGSON_DIAG_ITLB);
+				}
+				if (val & LOONGSON_DIAG_DTLB) {
+					/* Flush DTLB */
+					set_c0_diag(LOONGSON_DIAG_DTLB);
+				}
+				if (val & LOONGSON_DIAG_VTLB) {
+					/* Flush VTLB */
+					kvm_loongson_clear_guest_vtlb();
+				}
+				if (val & LOONGSON_DIAG_FTLB) {
+					/* Flush FTLB */
+					kvm_loongson_clear_guest_ftlb();
+				}
+				local_irq_restore(flags);
+#endif
+			} else {
+				er = EMULATE_FAIL;
+			}
+			break;
+
+		default:
+			er = EMULATE_FAIL;
+			break;
+		}
+	}
+	/* Rollback PC only if emulation was unsuccessful */
+	if (er == EMULATE_FAIL) {
+		kvm_err("[%#lx]%s: unsupported cop0 instruction 0x%08x\n",
+			curr_pc, __func__, inst.word);
+
+		vcpu->arch.pc = curr_pc;
+	}
+
+	return er;
+}
+
+static enum emulation_result kvm_vz_gpsi_cache(union mips_instruction inst,
+					       u32 *opc, u32 cause,
+					       struct kvm_vcpu *vcpu)
+{
+	enum emulation_result er = EMULATE_DONE;
+	u32 cache, op_inst, op, base;
+	s16 offset;
+	struct kvm_vcpu_arch *arch = &vcpu->arch;
+	unsigned long va, curr_pc;
+
+	/*
+	 * Update PC and hold onto current PC in case there is
+	 * an error and we want to rollback the PC
+	 */
+	curr_pc = vcpu->arch.pc;
+	er = update_pc(vcpu, cause);
+	if (er == EMULATE_FAIL)
+		return er;
+
+	base = inst.i_format.rs;
+	op_inst = inst.i_format.rt;
+	if (cpu_has_mips_r6)
+		offset = inst.spec3_format.simmediate;
+	else
+		offset = inst.i_format.simmediate;
+	cache = op_inst & CacheOp_Cache;
+	op = op_inst & CacheOp_Op;
+
+	va = arch->gprs[base] + offset;
+
+	kvm_debug("CACHE (cache: %#x, op: %#x, base[%d]: %#lx, offset: %#x\n",
+		  cache, op, base, arch->gprs[base], offset);
+
+	/* Secondary or tirtiary cache ops ignored */
+	if (cache != Cache_I && cache != Cache_D)
+		return EMULATE_DONE;
+
+	switch (op_inst) {
+	case Index_Invalidate_I:
+		flush_icache_line_indexed(va);
+		return EMULATE_DONE;
+	case Index_Writeback_Inv_D:
+		flush_dcache_line_indexed(va);
+		return EMULATE_DONE;
+	case Hit_Invalidate_I:
+	case Hit_Invalidate_D:
+	case Hit_Writeback_Inv_D:
+		if (boot_cpu_type() == CPU_CAVIUM_OCTEON3) {
+			/* We can just flush entire icache */
+			local_flush_icache_range(0, 0);
+			return EMULATE_DONE;
+		}
+
+		/* So far, other platforms support guest hit cache ops */
+		break;
+	default:
+		break;
+	}
+
+	kvm_err("@ %#lx/%#lx CACHE (cache: %#x, op: %#x, base[%d]: %#lx, offset: %#x\n",
+		curr_pc, vcpu->arch.gprs[31], cache, op, base, arch->gprs[base],
+		offset);
+	/* Rollback PC */
+	vcpu->arch.pc = curr_pc;
+
+	return EMULATE_FAIL;
+}
+
+#ifdef CONFIG_CPU_LOONGSON64
+static enum emulation_result kvm_vz_gpsi_lwc2(union mips_instruction inst,
+					      u32 *opc, u32 cause,
+					      struct kvm_vcpu *vcpu)
+{
+	unsigned int rs, rd;
+	unsigned int hostcfg;
+	unsigned long curr_pc;
+	enum emulation_result er = EMULATE_DONE;
+
+	/*
+	 * Update PC and hold onto current PC in case there is
+	 * an error and we want to rollback the PC
+	 */
+	curr_pc = vcpu->arch.pc;
+	er = update_pc(vcpu, cause);
+	if (er == EMULATE_FAIL)
+		return er;
+
+	rs = inst.loongson3_lscsr_format.rs;
+	rd = inst.loongson3_lscsr_format.rd;
+	switch (inst.loongson3_lscsr_format.fr) {
+	case 0x8:  /* Read CPUCFG */
+		++vcpu->stat.vz_cpucfg_exits;
+		hostcfg = read_cpucfg(vcpu->arch.gprs[rs]);
+
+		switch (vcpu->arch.gprs[rs]) {
+		case LOONGSON_CFG0:
+			vcpu->arch.gprs[rd] = 0x14c000;
+			break;
+		case LOONGSON_CFG1:
+			hostcfg &= (LOONGSON_CFG1_FP | LOONGSON_CFG1_MMI |
+				    LOONGSON_CFG1_MSA1 | LOONGSON_CFG1_MSA2 |
+				    LOONGSON_CFG1_SFBP);
+			vcpu->arch.gprs[rd] = hostcfg;
+			break;
+		case LOONGSON_CFG2:
+			hostcfg &= (LOONGSON_CFG2_LEXT1 | LOONGSON_CFG2_LEXT2 |
+				    LOONGSON_CFG2_LEXT3 | LOONGSON_CFG2_LSPW);
+			vcpu->arch.gprs[rd] = hostcfg;
+			break;
+		case LOONGSON_CFG3:
+			vcpu->arch.gprs[rd] = hostcfg;
+			break;
+		default:
+			/* Don't export any other advanced features to guest */
+			vcpu->arch.gprs[rd] = 0;
+			break;
+		}
+		break;
+
+	default:
+		kvm_err("lwc2 emulate not impl %d rs %lx @%lx\n",
+			inst.loongson3_lscsr_format.fr, vcpu->arch.gprs[rs], curr_pc);
+		er = EMULATE_FAIL;
+		break;
+	}
+
+	/* Rollback PC only if emulation was unsuccessful */
+	if (er == EMULATE_FAIL) {
+		kvm_err("[%#lx]%s: unsupported lwc2 instruction 0x%08x 0x%08x\n",
+			curr_pc, __func__, inst.word, inst.loongson3_lscsr_format.fr);
+
+		vcpu->arch.pc = curr_pc;
+	}
+
+	return er;
+}
+#endif
+
+static enum emulation_result kvm_trap_vz_handle_gpsi(u32 cause, u32 *opc,
+						     struct kvm_vcpu *vcpu)
+{
+	enum emulation_result er = EMULATE_DONE;
+	struct kvm_vcpu_arch *arch = &vcpu->arch;
+	union mips_instruction inst;
+	int rd, rt, sel;
+	int err;
+
+	/*
+	 *  Fetch the instruction.
+	 */
+	if (cause & CAUSEF_BD)
+		opc += 1;
+	err = kvm_get_badinstr(opc, vcpu, &inst.word);
+	if (err)
+		return EMULATE_FAIL;
+
+	switch (inst.r_format.opcode) {
+	case cop0_op:
+		er = kvm_vz_gpsi_cop0(inst, opc, cause, vcpu);
+		break;
+#ifndef CONFIG_CPU_MIPSR6
+	case cache_op:
+		trace_kvm_exit(vcpu, KVM_TRACE_EXIT_CACHE);
+		er = kvm_vz_gpsi_cache(inst, opc, cause, vcpu);
+		break;
+#endif
+#ifdef CONFIG_CPU_LOONGSON64
+	case lwc2_op:
+		er = kvm_vz_gpsi_lwc2(inst, opc, cause, vcpu);
+		break;
+#endif
+	case spec3_op:
+		switch (inst.spec3_format.func) {
+#ifdef CONFIG_CPU_MIPSR6
+		case cache6_op:
+			trace_kvm_exit(vcpu, KVM_TRACE_EXIT_CACHE);
+			er = kvm_vz_gpsi_cache(inst, opc, cause, vcpu);
+			break;
+#endif
+		case rdhwr_op:
+			if (inst.r_format.rs || (inst.r_format.re >> 3))
+				goto unknown;
+
+			rd = inst.r_format.rd;
+			rt = inst.r_format.rt;
+			sel = inst.r_format.re & 0x7;
+
+			switch (rd) {
+			case MIPS_HWR_CC:	/* Read count register */
+				arch->gprs[rt] =
+					(long)(int)kvm_mips_read_count(vcpu);
+				break;
+			default:
+				trace_kvm_hwr(vcpu, KVM_TRACE_RDHWR,
+					      KVM_TRACE_HWR(rd, sel), 0);
+				goto unknown;
+			}
+
+			trace_kvm_hwr(vcpu, KVM_TRACE_RDHWR,
+				      KVM_TRACE_HWR(rd, sel), arch->gprs[rt]);
+
+			er = update_pc(vcpu, cause);
+			break;
+		default:
+			goto unknown;
+		}
+		break;
+unknown:
+
+	default:
+		kvm_err("GPSI exception not supported (%p/%#x)\n",
+				opc, inst.word);
+		kvm_arch_vcpu_dump_regs(vcpu);
+		er = EMULATE_FAIL;
+		break;
+	}
+
+	return er;
+}
+
+static enum emulation_result kvm_trap_vz_handle_gsfc(u32 cause, u32 *opc,
+						     struct kvm_vcpu *vcpu)
+{
+	enum emulation_result er = EMULATE_DONE;
+	struct kvm_vcpu_arch *arch = &vcpu->arch;
+	union mips_instruction inst;
+	int err;
+
+	/*
+	 *  Fetch the instruction.
+	 */
+	if (cause & CAUSEF_BD)
+		opc += 1;
+	err = kvm_get_badinstr(opc, vcpu, &inst.word);
+	if (err)
+		return EMULATE_FAIL;
+
+	/* complete MTC0 on behalf of guest and advance EPC */
+	if (inst.c0r_format.opcode == cop0_op &&
+	    inst.c0r_format.rs == mtc_op &&
+	    inst.c0r_format.z == 0) {
+		int rt = inst.c0r_format.rt;
+		int rd = inst.c0r_format.rd;
+		int sel = inst.c0r_format.sel;
+		unsigned int val = arch->gprs[rt];
+		unsigned int old_val, change;
+
+		trace_kvm_hwr(vcpu, KVM_TRACE_MTC0, KVM_TRACE_COP0(rd, sel),
+			      val);
+
+		if ((rd == MIPS_CP0_STATUS) && (sel == 0)) {
+			/* FR bit should read as zero if no FPU */
+			if (!kvm_mips_guest_has_fpu(&vcpu->arch))
+				val &= ~(ST0_CU1 | ST0_FR);
+
+			/*
+			 * Also don't allow FR to be set if host doesn't support
+			 * it.
+			 */
+			if (!(boot_cpu_data.fpu_id & MIPS_FPIR_F64))
+				val &= ~ST0_FR;
+
+			old_val = read_gc0_status();
+			change = val ^ old_val;
+
+			if (change & ST0_FR) {
+				/*
+				 * FPU and Vector register state is made
+				 * UNPREDICTABLE by a change of FR, so don't
+				 * even bother saving it.
+				 */
+				kvm_drop_fpu(vcpu);
+			}
+
+			/*
+			 * If MSA state is already live, it is undefined how it
+			 * interacts with FR=0 FPU state, and we don't want to
+			 * hit reserved instruction exceptions trying to save
+			 * the MSA state later when CU=1 && FR=1, so play it
+			 * safe and save it first.
+			 */
+			if (change & ST0_CU1 && !(val & ST0_FR) &&
+			    vcpu->arch.aux_inuse & KVM_MIPS_AUX_MSA)
+				kvm_lose_fpu(vcpu);
+
+			write_gc0_status(val);
+		} else if ((rd == MIPS_CP0_CAUSE) && (sel == 0)) {
+			u32 old_cause = read_gc0_cause();
+			u32 change = old_cause ^ val;
+
+			/* DC bit enabling/disabling timer? */
+			if (change & CAUSEF_DC) {
+				if (val & CAUSEF_DC) {
+					kvm_vz_lose_htimer(vcpu);
+					kvm_mips_count_disable_cause(vcpu);
+				} else {
+					kvm_mips_count_enable_cause(vcpu);
+				}
+			}
+
+			/* Only certain bits are RW to the guest */
+			change &= (CAUSEF_DC | CAUSEF_IV | CAUSEF_WP |
+				   CAUSEF_IP0 | CAUSEF_IP1);
+
+			/* WP can only be cleared */
+			change &= ~CAUSEF_WP | old_cause;
+
+			write_gc0_cause(old_cause ^ change);
+		} else if ((rd == MIPS_CP0_STATUS) && (sel == 1)) { /* IntCtl */
+			write_gc0_intctl(val);
+		} else if ((rd == MIPS_CP0_CONFIG) && (sel == 5)) {
+			old_val = read_gc0_config5();
+			change = val ^ old_val;
+			/* Handle changes in FPU/MSA modes */
+			preempt_disable();
+
+			/*
+			 * Propagate FRE changes immediately if the FPU
+			 * context is already loaded.
+			 */
+			if (change & MIPS_CONF5_FRE &&
+			    vcpu->arch.aux_inuse & KVM_MIPS_AUX_FPU)
+				change_c0_config5(MIPS_CONF5_FRE, val);
+
+			preempt_enable();
+
+			val = old_val ^
+				(change & kvm_vz_config5_guest_wrmask(vcpu));
+			write_gc0_config5(val);
+		} else {
+			kvm_err("Handle GSFC, unsupported field change @ %p: %#x\n",
+			    opc, inst.word);
+			er = EMULATE_FAIL;
+		}
+
+		if (er != EMULATE_FAIL)
+			er = update_pc(vcpu, cause);
+	} else {
+		kvm_err("Handle GSFC, unrecognized instruction @ %p: %#x\n",
+			opc, inst.word);
+		er = EMULATE_FAIL;
+	}
+
+	return er;
+}
+
+static enum emulation_result kvm_trap_vz_handle_ghfc(u32 cause, u32 *opc,
+						     struct kvm_vcpu *vcpu)
+{
+	/*
+	 * Presumably this is due to MC (guest mode change), so lets trace some
+	 * relevant info.
+	 */
+	trace_kvm_guest_mode_change(vcpu);
+
+	return EMULATE_DONE;
+}
+
+static enum emulation_result kvm_trap_vz_handle_hc(u32 cause, u32 *opc,
+						   struct kvm_vcpu *vcpu)
+{
+	enum emulation_result er;
+	union mips_instruction inst;
+	unsigned long curr_pc;
+	int err;
+
+	if (cause & CAUSEF_BD)
+		opc += 1;
+	err = kvm_get_badinstr(opc, vcpu, &inst.word);
+	if (err)
+		return EMULATE_FAIL;
+
+	/*
+	 * Update PC and hold onto current PC in case there is
+	 * an error and we want to rollback the PC
+	 */
+	curr_pc = vcpu->arch.pc;
+	er = update_pc(vcpu, cause);
+	if (er == EMULATE_FAIL)
+		return er;
+
+	er = kvm_mips_emul_hypcall(vcpu, inst);
+	if (er == EMULATE_FAIL)
+		vcpu->arch.pc = curr_pc;
+
+	return er;
+}
+
+static enum emulation_result kvm_trap_vz_no_handler_guest_exit(u32 gexccode,
+							u32 cause,
+							u32 *opc,
+							struct kvm_vcpu *vcpu)
+{
+	u32 inst;
+
+	/*
+	 *  Fetch the instruction.
+	 */
+	if (cause & CAUSEF_BD)
+		opc += 1;
+	kvm_get_badinstr(opc, vcpu, &inst);
+
+	kvm_err("Guest Exception Code: %d not yet handled @ PC: %p, inst: 0x%08x  Status: %#x\n",
+		gexccode, opc, inst, read_gc0_status());
+
+	return EMULATE_FAIL;
+}
+
+static int kvm_trap_vz_handle_guest_exit(struct kvm_vcpu *vcpu)
+{
+	u32 *opc = (u32 *) vcpu->arch.pc;
+	u32 cause = vcpu->arch.host_cp0_cause;
+	enum emulation_result er = EMULATE_DONE;
+	u32 gexccode = (vcpu->arch.host_cp0_guestctl0 &
+			MIPS_GCTL0_GEXC) >> MIPS_GCTL0_GEXC_SHIFT;
+	int ret = RESUME_GUEST;
+
+	trace_kvm_exit(vcpu, KVM_TRACE_EXIT_GEXCCODE_BASE + gexccode);
+	switch (gexccode) {
+	case MIPS_GCTL0_GEXC_GPSI:
+		++vcpu->stat.vz_gpsi_exits;
+		er = kvm_trap_vz_handle_gpsi(cause, opc, vcpu);
+		break;
+	case MIPS_GCTL0_GEXC_GSFC:
+		++vcpu->stat.vz_gsfc_exits;
+		er = kvm_trap_vz_handle_gsfc(cause, opc, vcpu);
+		break;
+	case MIPS_GCTL0_GEXC_HC:
+		++vcpu->stat.vz_hc_exits;
+		er = kvm_trap_vz_handle_hc(cause, opc, vcpu);
+		break;
+	case MIPS_GCTL0_GEXC_GRR:
+		++vcpu->stat.vz_grr_exits;
+		er = kvm_trap_vz_no_handler_guest_exit(gexccode, cause, opc,
+						       vcpu);
+		break;
+	case MIPS_GCTL0_GEXC_GVA:
+		++vcpu->stat.vz_gva_exits;
+		er = kvm_trap_vz_no_handler_guest_exit(gexccode, cause, opc,
+						       vcpu);
+		break;
+	case MIPS_GCTL0_GEXC_GHFC:
+		++vcpu->stat.vz_ghfc_exits;
+		er = kvm_trap_vz_handle_ghfc(cause, opc, vcpu);
+		break;
+	case MIPS_GCTL0_GEXC_GPA:
+		++vcpu->stat.vz_gpa_exits;
+		er = kvm_trap_vz_no_handler_guest_exit(gexccode, cause, opc,
+						       vcpu);
+		break;
+	default:
+		++vcpu->stat.vz_resvd_exits;
+		er = kvm_trap_vz_no_handler_guest_exit(gexccode, cause, opc,
+						       vcpu);
+		break;
+
+	}
+
+	if (er == EMULATE_DONE) {
+		ret = RESUME_GUEST;
+	} else if (er == EMULATE_HYPERCALL) {
+		ret = kvm_mips_handle_hypcall(vcpu);
+	} else {
+		vcpu->run->exit_reason = KVM_EXIT_INTERNAL_ERROR;
+		ret = RESUME_HOST;
+	}
+	return ret;
+}
+
+/**
+ * kvm_trap_vz_handle_cop_unusable() - Guest used unusable coprocessor.
+ * @vcpu:	Virtual CPU context.
+ *
+ * Handle when the guest attempts to use a coprocessor which hasn't been allowed
+ * by the root context.
+ *
+ * Return: value indicating whether to resume the host or the guest
+ * 	   (RESUME_HOST or RESUME_GUEST)
+ */
+static int kvm_trap_vz_handle_cop_unusable(struct kvm_vcpu *vcpu)
+{
+	u32 cause = vcpu->arch.host_cp0_cause;
+	enum emulation_result er = EMULATE_FAIL;
+	int ret = RESUME_GUEST;
+
+	if (((cause & CAUSEF_CE) >> CAUSEB_CE) == 1) {
+		/*
+		 * If guest FPU not present, the FPU operation should have been
+		 * treated as a reserved instruction!
+		 * If FPU already in use, we shouldn't get this at all.
+		 */
+		if (WARN_ON(!kvm_mips_guest_has_fpu(&vcpu->arch) ||
+			    vcpu->arch.aux_inuse & KVM_MIPS_AUX_FPU)) {
+			preempt_enable();
+			return EMULATE_FAIL;
+		}
+
+		kvm_own_fpu(vcpu);
+		er = EMULATE_DONE;
+	}
+	/* other coprocessors not handled */
+
+	switch (er) {
+	case EMULATE_DONE:
+		ret = RESUME_GUEST;
+		break;
+
+	case EMULATE_FAIL:
+		vcpu->run->exit_reason = KVM_EXIT_INTERNAL_ERROR;
+		ret = RESUME_HOST;
+		break;
+
+	default:
+		BUG();
+	}
+	return ret;
+}
+
+/**
+ * kvm_trap_vz_handle_msa_disabled() - Guest used MSA while disabled in root.
+ * @vcpu:	Virtual CPU context.
+ *
+ * Handle when the guest attempts to use MSA when it is disabled in the root
+ * context.
+ *
+ * Return: value indicating whether to resume the host or the guest
+ * 	   (RESUME_HOST or RESUME_GUEST)
+ */
+static int kvm_trap_vz_handle_msa_disabled(struct kvm_vcpu *vcpu)
+{
+	/*
+	 * If MSA not present or not exposed to guest or FR=0, the MSA operation
+	 * should have been treated as a reserved instruction!
+	 * Same if CU1=1, FR=0.
+	 * If MSA already in use, we shouldn't get this at all.
+	 */
+	if (!kvm_mips_guest_has_msa(&vcpu->arch) ||
+	    (read_gc0_status() & (ST0_CU1 | ST0_FR)) == ST0_CU1 ||
+	    !(read_gc0_config5() & MIPS_CONF5_MSAEN) ||
+	    vcpu->arch.aux_inuse & KVM_MIPS_AUX_MSA) {
+		vcpu->run->exit_reason = KVM_EXIT_INTERNAL_ERROR;
+		return RESUME_HOST;
+	}
+
+	kvm_own_msa(vcpu);
+
+	return RESUME_GUEST;
+}
+
+static int kvm_trap_vz_handle_tlb_ld_miss(struct kvm_vcpu *vcpu)
+{
+	struct kvm_run *run = vcpu->run;
+	u32 *opc = (u32 *) vcpu->arch.pc;
+	u32 cause = vcpu->arch.host_cp0_cause;
+	ulong badvaddr = vcpu->arch.host_cp0_badvaddr;
+	union mips_instruction inst;
+	enum emulation_result er = EMULATE_DONE;
+	int err, ret = RESUME_GUEST;
+
+	if (kvm_mips_handle_vz_root_tlb_fault(badvaddr, vcpu, false)) {
+		/* A code fetch fault doesn't count as an MMIO */
+		if (kvm_is_ifetch_fault(&vcpu->arch)) {
+			run->exit_reason = KVM_EXIT_INTERNAL_ERROR;
+			return RESUME_HOST;
+		}
+
+		/* Fetch the instruction */
+		if (cause & CAUSEF_BD)
+			opc += 1;
+		err = kvm_get_badinstr(opc, vcpu, &inst.word);
+		if (err) {
+			run->exit_reason = KVM_EXIT_INTERNAL_ERROR;
+			return RESUME_HOST;
+		}
+
+		/* Treat as MMIO */
+		er = kvm_mips_emulate_load(inst, cause, vcpu);
+		if (er == EMULATE_FAIL) {
+			kvm_err("Guest Emulate Load from MMIO space failed: PC: %p, BadVaddr: %#lx\n",
+				opc, badvaddr);
+			run->exit_reason = KVM_EXIT_INTERNAL_ERROR;
+		}
+	}
+
+	if (er == EMULATE_DONE) {
+		ret = RESUME_GUEST;
+	} else if (er == EMULATE_DO_MMIO) {
+		run->exit_reason = KVM_EXIT_MMIO;
+		ret = RESUME_HOST;
+	} else {
+		run->exit_reason = KVM_EXIT_INTERNAL_ERROR;
+		ret = RESUME_HOST;
+	}
+	return ret;
+}
+
+static int kvm_trap_vz_handle_tlb_st_miss(struct kvm_vcpu *vcpu)
+{
+	struct kvm_run *run = vcpu->run;
+	u32 *opc = (u32 *) vcpu->arch.pc;
+	u32 cause = vcpu->arch.host_cp0_cause;
+	ulong badvaddr = vcpu->arch.host_cp0_badvaddr;
+	union mips_instruction inst;
+	enum emulation_result er = EMULATE_DONE;
+	int err;
+	int ret = RESUME_GUEST;
+
+	/* Just try the access again if we couldn't do the translation */
+	if (kvm_vz_badvaddr_to_gpa(vcpu, badvaddr, &badvaddr))
+		return RESUME_GUEST;
+	vcpu->arch.host_cp0_badvaddr = badvaddr;
+
+	if (kvm_mips_handle_vz_root_tlb_fault(badvaddr, vcpu, true)) {
+		/* Fetch the instruction */
+		if (cause & CAUSEF_BD)
+			opc += 1;
+		err = kvm_get_badinstr(opc, vcpu, &inst.word);
+		if (err) {
+			run->exit_reason = KVM_EXIT_INTERNAL_ERROR;
+			return RESUME_HOST;
+		}
+
+		/* Treat as MMIO */
+		er = kvm_mips_emulate_store(inst, cause, vcpu);
+		if (er == EMULATE_FAIL) {
+			kvm_err("Guest Emulate Store to MMIO space failed: PC: %p, BadVaddr: %#lx\n",
+				opc, badvaddr);
+			run->exit_reason = KVM_EXIT_INTERNAL_ERROR;
+		}
+	}
+
+	if (er == EMULATE_DONE) {
+		ret = RESUME_GUEST;
+	} else if (er == EMULATE_DO_MMIO) {
+		run->exit_reason = KVM_EXIT_MMIO;
+		ret = RESUME_HOST;
+	} else {
+		run->exit_reason = KVM_EXIT_INTERNAL_ERROR;
+		ret = RESUME_HOST;
+	}
+	return ret;
+}
+
+static u64 kvm_vz_get_one_regs[] = {
+	KVM_REG_MIPS_CP0_INDEX,
+	KVM_REG_MIPS_CP0_ENTRYLO0,
+	KVM_REG_MIPS_CP0_ENTRYLO1,
+	KVM_REG_MIPS_CP0_CONTEXT,
+	KVM_REG_MIPS_CP0_PAGEMASK,
+	KVM_REG_MIPS_CP0_PAGEGRAIN,
+	KVM_REG_MIPS_CP0_WIRED,
+	KVM_REG_MIPS_CP0_HWRENA,
+	KVM_REG_MIPS_CP0_BADVADDR,
+	KVM_REG_MIPS_CP0_COUNT,
+	KVM_REG_MIPS_CP0_ENTRYHI,
+	KVM_REG_MIPS_CP0_COMPARE,
+	KVM_REG_MIPS_CP0_STATUS,
+	KVM_REG_MIPS_CP0_INTCTL,
+	KVM_REG_MIPS_CP0_CAUSE,
+	KVM_REG_MIPS_CP0_EPC,
+	KVM_REG_MIPS_CP0_PRID,
+	KVM_REG_MIPS_CP0_EBASE,
+	KVM_REG_MIPS_CP0_CONFIG,
+	KVM_REG_MIPS_CP0_CONFIG1,
+	KVM_REG_MIPS_CP0_CONFIG2,
+	KVM_REG_MIPS_CP0_CONFIG3,
+	KVM_REG_MIPS_CP0_CONFIG4,
+	KVM_REG_MIPS_CP0_CONFIG5,
+	KVM_REG_MIPS_CP0_CONFIG6,
+#ifdef CONFIG_64BIT
+	KVM_REG_MIPS_CP0_XCONTEXT,
+#endif
+	KVM_REG_MIPS_CP0_ERROREPC,
+
+	KVM_REG_MIPS_COUNT_CTL,
+	KVM_REG_MIPS_COUNT_RESUME,
+	KVM_REG_MIPS_COUNT_HZ,
+};
+
+static u64 kvm_vz_get_one_regs_contextconfig[] = {
+	KVM_REG_MIPS_CP0_CONTEXTCONFIG,
+#ifdef CONFIG_64BIT
+	KVM_REG_MIPS_CP0_XCONTEXTCONFIG,
+#endif
+};
+
+static u64 kvm_vz_get_one_regs_segments[] = {
+	KVM_REG_MIPS_CP0_SEGCTL0,
+	KVM_REG_MIPS_CP0_SEGCTL1,
+	KVM_REG_MIPS_CP0_SEGCTL2,
+};
+
+static u64 kvm_vz_get_one_regs_htw[] = {
+	KVM_REG_MIPS_CP0_PWBASE,
+	KVM_REG_MIPS_CP0_PWFIELD,
+	KVM_REG_MIPS_CP0_PWSIZE,
+	KVM_REG_MIPS_CP0_PWCTL,
+};
+
+static u64 kvm_vz_get_one_regs_kscratch[] = {
+	KVM_REG_MIPS_CP0_KSCRATCH1,
+	KVM_REG_MIPS_CP0_KSCRATCH2,
+	KVM_REG_MIPS_CP0_KSCRATCH3,
+	KVM_REG_MIPS_CP0_KSCRATCH4,
+	KVM_REG_MIPS_CP0_KSCRATCH5,
+	KVM_REG_MIPS_CP0_KSCRATCH6,
+};
+
+static unsigned long kvm_vz_num_regs(struct kvm_vcpu *vcpu)
+{
+	unsigned long ret;
+
+	ret = ARRAY_SIZE(kvm_vz_get_one_regs);
+	if (cpu_guest_has_userlocal)
+		++ret;
+	if (cpu_guest_has_badinstr)
+		++ret;
+	if (cpu_guest_has_badinstrp)
+		++ret;
+	if (cpu_guest_has_contextconfig)
+		ret += ARRAY_SIZE(kvm_vz_get_one_regs_contextconfig);
+	if (cpu_guest_has_segments)
+		ret += ARRAY_SIZE(kvm_vz_get_one_regs_segments);
+	if (cpu_guest_has_htw || cpu_guest_has_ldpte)
+		ret += ARRAY_SIZE(kvm_vz_get_one_regs_htw);
+	if (cpu_guest_has_maar && !cpu_guest_has_dyn_maar)
+		ret += 1 + ARRAY_SIZE(vcpu->arch.maar);
+	ret += __arch_hweight8(cpu_data[0].guest.kscratch_mask);
+
+	return ret;
+}
+
+static int kvm_vz_copy_reg_indices(struct kvm_vcpu *vcpu, u64 __user *indices)
+{
+	u64 index;
+	unsigned int i;
+
+	if (copy_to_user(indices, kvm_vz_get_one_regs,
+			 sizeof(kvm_vz_get_one_regs)))
+		return -EFAULT;
+	indices += ARRAY_SIZE(kvm_vz_get_one_regs);
+
+	if (cpu_guest_has_userlocal) {
+		index = KVM_REG_MIPS_CP0_USERLOCAL;
+		if (copy_to_user(indices, &index, sizeof(index)))
+			return -EFAULT;
+		++indices;
+	}
+	if (cpu_guest_has_badinstr) {
+		index = KVM_REG_MIPS_CP0_BADINSTR;
+		if (copy_to_user(indices, &index, sizeof(index)))
+			return -EFAULT;
+		++indices;
+	}
+	if (cpu_guest_has_badinstrp) {
+		index = KVM_REG_MIPS_CP0_BADINSTRP;
+		if (copy_to_user(indices, &index, sizeof(index)))
+			return -EFAULT;
+		++indices;
+	}
+	if (cpu_guest_has_contextconfig) {
+		if (copy_to_user(indices, kvm_vz_get_one_regs_contextconfig,
+				 sizeof(kvm_vz_get_one_regs_contextconfig)))
+			return -EFAULT;
+		indices += ARRAY_SIZE(kvm_vz_get_one_regs_contextconfig);
+	}
+	if (cpu_guest_has_segments) {
+		if (copy_to_user(indices, kvm_vz_get_one_regs_segments,
+				 sizeof(kvm_vz_get_one_regs_segments)))
+			return -EFAULT;
+		indices += ARRAY_SIZE(kvm_vz_get_one_regs_segments);
+	}
+	if (cpu_guest_has_htw || cpu_guest_has_ldpte) {
+		if (copy_to_user(indices, kvm_vz_get_one_regs_htw,
+				 sizeof(kvm_vz_get_one_regs_htw)))
+			return -EFAULT;
+		indices += ARRAY_SIZE(kvm_vz_get_one_regs_htw);
+	}
+	if (cpu_guest_has_maar && !cpu_guest_has_dyn_maar) {
+		for (i = 0; i < ARRAY_SIZE(vcpu->arch.maar); ++i) {
+			index = KVM_REG_MIPS_CP0_MAAR(i);
+			if (copy_to_user(indices, &index, sizeof(index)))
+				return -EFAULT;
+			++indices;
+		}
+
+		index = KVM_REG_MIPS_CP0_MAARI;
+		if (copy_to_user(indices, &index, sizeof(index)))
+			return -EFAULT;
+		++indices;
+	}
+	for (i = 0; i < 6; ++i) {
+		if (!cpu_guest_has_kscr(i + 2))
+			continue;
+
+		if (copy_to_user(indices, &kvm_vz_get_one_regs_kscratch[i],
+				 sizeof(kvm_vz_get_one_regs_kscratch[i])))
+			return -EFAULT;
+		++indices;
+	}
+
+	return 0;
+}
+
+static inline s64 entrylo_kvm_to_user(unsigned long v)
+{
+	s64 mask, ret = v;
+
+	if (BITS_PER_LONG == 32) {
+		/*
+		 * KVM API exposes 64-bit version of the register, so move the
+		 * RI/XI bits up into place.
+		 */
+		mask = MIPS_ENTRYLO_RI | MIPS_ENTRYLO_XI;
+		ret &= ~mask;
+		ret |= ((s64)v & mask) << 32;
+	}
+	return ret;
+}
+
+static inline unsigned long entrylo_user_to_kvm(s64 v)
+{
+	unsigned long mask, ret = v;
+
+	if (BITS_PER_LONG == 32) {
+		/*
+		 * KVM API exposes 64-bit versiono of the register, so move the
+		 * RI/XI bits down into place.
+		 */
+		mask = MIPS_ENTRYLO_RI | MIPS_ENTRYLO_XI;
+		ret &= ~mask;
+		ret |= (v >> 32) & mask;
+	}
+	return ret;
+}
+
+static int kvm_vz_get_one_reg(struct kvm_vcpu *vcpu,
+			      const struct kvm_one_reg *reg,
+			      s64 *v)
+{
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
+	unsigned int idx;
+
+	switch (reg->id) {
+	case KVM_REG_MIPS_CP0_INDEX:
+		*v = (long)read_gc0_index();
+		break;
+	case KVM_REG_MIPS_CP0_ENTRYLO0:
+		*v = entrylo_kvm_to_user(read_gc0_entrylo0());
+		break;
+	case KVM_REG_MIPS_CP0_ENTRYLO1:
+		*v = entrylo_kvm_to_user(read_gc0_entrylo1());
+		break;
+	case KVM_REG_MIPS_CP0_CONTEXT:
+		*v = (long)read_gc0_context();
+		break;
+	case KVM_REG_MIPS_CP0_CONTEXTCONFIG:
+		if (!cpu_guest_has_contextconfig)
+			return -EINVAL;
+		*v = read_gc0_contextconfig();
+		break;
+	case KVM_REG_MIPS_CP0_USERLOCAL:
+		if (!cpu_guest_has_userlocal)
+			return -EINVAL;
+		*v = read_gc0_userlocal();
+		break;
+#ifdef CONFIG_64BIT
+	case KVM_REG_MIPS_CP0_XCONTEXTCONFIG:
+		if (!cpu_guest_has_contextconfig)
+			return -EINVAL;
+		*v = read_gc0_xcontextconfig();
+		break;
+#endif
+	case KVM_REG_MIPS_CP0_PAGEMASK:
+		*v = (long)read_gc0_pagemask();
+		break;
+	case KVM_REG_MIPS_CP0_PAGEGRAIN:
+		*v = (long)read_gc0_pagegrain();
+		break;
+	case KVM_REG_MIPS_CP0_SEGCTL0:
+		if (!cpu_guest_has_segments)
+			return -EINVAL;
+		*v = read_gc0_segctl0();
+		break;
+	case KVM_REG_MIPS_CP0_SEGCTL1:
+		if (!cpu_guest_has_segments)
+			return -EINVAL;
+		*v = read_gc0_segctl1();
+		break;
+	case KVM_REG_MIPS_CP0_SEGCTL2:
+		if (!cpu_guest_has_segments)
+			return -EINVAL;
+		*v = read_gc0_segctl2();
+		break;
+	case KVM_REG_MIPS_CP0_PWBASE:
+		if (!cpu_guest_has_htw && !cpu_guest_has_ldpte)
+			return -EINVAL;
+		*v = read_gc0_pwbase();
+		break;
+	case KVM_REG_MIPS_CP0_PWFIELD:
+		if (!cpu_guest_has_htw && !cpu_guest_has_ldpte)
+			return -EINVAL;
+		*v = read_gc0_pwfield();
+		break;
+	case KVM_REG_MIPS_CP0_PWSIZE:
+		if (!cpu_guest_has_htw && !cpu_guest_has_ldpte)
+			return -EINVAL;
+		*v = read_gc0_pwsize();
+		break;
+	case KVM_REG_MIPS_CP0_WIRED:
+		*v = (long)read_gc0_wired();
+		break;
+	case KVM_REG_MIPS_CP0_PWCTL:
+		if (!cpu_guest_has_htw && !cpu_guest_has_ldpte)
+			return -EINVAL;
+		*v = read_gc0_pwctl();
+		break;
+	case KVM_REG_MIPS_CP0_HWRENA:
+		*v = (long)read_gc0_hwrena();
+		break;
+	case KVM_REG_MIPS_CP0_BADVADDR:
+		*v = (long)read_gc0_badvaddr();
+		break;
+	case KVM_REG_MIPS_CP0_BADINSTR:
+		if (!cpu_guest_has_badinstr)
+			return -EINVAL;
+		*v = read_gc0_badinstr();
+		break;
+	case KVM_REG_MIPS_CP0_BADINSTRP:
+		if (!cpu_guest_has_badinstrp)
+			return -EINVAL;
+		*v = read_gc0_badinstrp();
+		break;
+	case KVM_REG_MIPS_CP0_COUNT:
+		*v = kvm_mips_read_count(vcpu);
+		break;
+	case KVM_REG_MIPS_CP0_ENTRYHI:
+		*v = (long)read_gc0_entryhi();
+		break;
+	case KVM_REG_MIPS_CP0_COMPARE:
+		*v = (long)read_gc0_compare();
+		break;
+	case KVM_REG_MIPS_CP0_STATUS:
+		*v = (long)read_gc0_status();
+		break;
+	case KVM_REG_MIPS_CP0_INTCTL:
+		*v = read_gc0_intctl();
+		break;
+	case KVM_REG_MIPS_CP0_CAUSE:
+		*v = (long)read_gc0_cause();
+		break;
+	case KVM_REG_MIPS_CP0_EPC:
+		*v = (long)read_gc0_epc();
+		break;
+	case KVM_REG_MIPS_CP0_PRID:
+		switch (boot_cpu_type()) {
+		case CPU_CAVIUM_OCTEON3:
+			/* Octeon III has a read-only guest.PRid */
+			*v = read_gc0_prid();
+			break;
+		default:
+			*v = (long)kvm_read_c0_guest_prid(cop0);
+			break;
+		}
+		break;
+	case KVM_REG_MIPS_CP0_EBASE:
+		*v = kvm_vz_read_gc0_ebase();
+		break;
+	case KVM_REG_MIPS_CP0_CONFIG:
+		*v = read_gc0_config();
+		break;
+	case KVM_REG_MIPS_CP0_CONFIG1:
+		if (!cpu_guest_has_conf1)
+			return -EINVAL;
+		*v = read_gc0_config1();
+		break;
+	case KVM_REG_MIPS_CP0_CONFIG2:
+		if (!cpu_guest_has_conf2)
+			return -EINVAL;
+		*v = read_gc0_config2();
+		break;
+	case KVM_REG_MIPS_CP0_CONFIG3:
+		if (!cpu_guest_has_conf3)
+			return -EINVAL;
+		*v = read_gc0_config3();
+		break;
+	case KVM_REG_MIPS_CP0_CONFIG4:
+		if (!cpu_guest_has_conf4)
+			return -EINVAL;
+		*v = read_gc0_config4();
+		break;
+	case KVM_REG_MIPS_CP0_CONFIG5:
+		if (!cpu_guest_has_conf5)
+			return -EINVAL;
+		*v = read_gc0_config5();
+		break;
+	case KVM_REG_MIPS_CP0_CONFIG6:
+		*v = kvm_read_sw_gc0_config6(cop0);
+		break;
+	case KVM_REG_MIPS_CP0_MAAR(0) ... KVM_REG_MIPS_CP0_MAAR(0x3f):
+		if (!cpu_guest_has_maar || cpu_guest_has_dyn_maar)
+			return -EINVAL;
+		idx = reg->id - KVM_REG_MIPS_CP0_MAAR(0);
+		if (idx >= ARRAY_SIZE(vcpu->arch.maar))
+			return -EINVAL;
+		*v = vcpu->arch.maar[idx];
+		break;
+	case KVM_REG_MIPS_CP0_MAARI:
+		if (!cpu_guest_has_maar || cpu_guest_has_dyn_maar)
+			return -EINVAL;
+		*v = kvm_read_sw_gc0_maari(&vcpu->arch.cop0);
+		break;
+#ifdef CONFIG_64BIT
+	case KVM_REG_MIPS_CP0_XCONTEXT:
+		*v = read_gc0_xcontext();
+		break;
+#endif
+	case KVM_REG_MIPS_CP0_ERROREPC:
+		*v = (long)read_gc0_errorepc();
+		break;
+	case KVM_REG_MIPS_CP0_KSCRATCH1 ... KVM_REG_MIPS_CP0_KSCRATCH6:
+		idx = reg->id - KVM_REG_MIPS_CP0_KSCRATCH1 + 2;
+		if (!cpu_guest_has_kscr(idx))
+			return -EINVAL;
+		switch (idx) {
+		case 2:
+			*v = (long)read_gc0_kscratch1();
+			break;
+		case 3:
+			*v = (long)read_gc0_kscratch2();
+			break;
+		case 4:
+			*v = (long)read_gc0_kscratch3();
+			break;
+		case 5:
+			*v = (long)read_gc0_kscratch4();
+			break;
+		case 6:
+			*v = (long)read_gc0_kscratch5();
+			break;
+		case 7:
+			*v = (long)read_gc0_kscratch6();
+			break;
+		}
+		break;
+	case KVM_REG_MIPS_COUNT_CTL:
+		*v = vcpu->arch.count_ctl;
+		break;
+	case KVM_REG_MIPS_COUNT_RESUME:
+		*v = ktime_to_ns(vcpu->arch.count_resume);
+		break;
+	case KVM_REG_MIPS_COUNT_HZ:
+		*v = vcpu->arch.count_hz;
+		break;
+	default:
+		return -EINVAL;
+	}
+	return 0;
+}
+
+static int kvm_vz_set_one_reg(struct kvm_vcpu *vcpu,
+			      const struct kvm_one_reg *reg,
+			      s64 v)
+{
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
+	unsigned int idx;
+	int ret = 0;
+	unsigned int cur, change;
+
+	switch (reg->id) {
+	case KVM_REG_MIPS_CP0_INDEX:
+		write_gc0_index(v);
+		break;
+	case KVM_REG_MIPS_CP0_ENTRYLO0:
+		write_gc0_entrylo0(entrylo_user_to_kvm(v));
+		break;
+	case KVM_REG_MIPS_CP0_ENTRYLO1:
+		write_gc0_entrylo1(entrylo_user_to_kvm(v));
+		break;
+	case KVM_REG_MIPS_CP0_CONTEXT:
+		write_gc0_context(v);
+		break;
+	case KVM_REG_MIPS_CP0_CONTEXTCONFIG:
+		if (!cpu_guest_has_contextconfig)
+			return -EINVAL;
+		write_gc0_contextconfig(v);
+		break;
+	case KVM_REG_MIPS_CP0_USERLOCAL:
+		if (!cpu_guest_has_userlocal)
+			return -EINVAL;
+		write_gc0_userlocal(v);
+		break;
+#ifdef CONFIG_64BIT
+	case KVM_REG_MIPS_CP0_XCONTEXTCONFIG:
+		if (!cpu_guest_has_contextconfig)
+			return -EINVAL;
+		write_gc0_xcontextconfig(v);
+		break;
+#endif
+	case KVM_REG_MIPS_CP0_PAGEMASK:
+		write_gc0_pagemask(v);
+		break;
+	case KVM_REG_MIPS_CP0_PAGEGRAIN:
+		write_gc0_pagegrain(v);
+		break;
+	case KVM_REG_MIPS_CP0_SEGCTL0:
+		if (!cpu_guest_has_segments)
+			return -EINVAL;
+		write_gc0_segctl0(v);
+		break;
+	case KVM_REG_MIPS_CP0_SEGCTL1:
+		if (!cpu_guest_has_segments)
+			return -EINVAL;
+		write_gc0_segctl1(v);
+		break;
+	case KVM_REG_MIPS_CP0_SEGCTL2:
+		if (!cpu_guest_has_segments)
+			return -EINVAL;
+		write_gc0_segctl2(v);
+		break;
+	case KVM_REG_MIPS_CP0_PWBASE:
+		if (!cpu_guest_has_htw && !cpu_guest_has_ldpte)
+			return -EINVAL;
+		write_gc0_pwbase(v);
+		break;
+	case KVM_REG_MIPS_CP0_PWFIELD:
+		if (!cpu_guest_has_htw && !cpu_guest_has_ldpte)
+			return -EINVAL;
+		write_gc0_pwfield(v);
+		break;
+	case KVM_REG_MIPS_CP0_PWSIZE:
+		if (!cpu_guest_has_htw && !cpu_guest_has_ldpte)
+			return -EINVAL;
+		write_gc0_pwsize(v);
+		break;
+	case KVM_REG_MIPS_CP0_WIRED:
+		change_gc0_wired(MIPSR6_WIRED_WIRED, v);
+		break;
+	case KVM_REG_MIPS_CP0_PWCTL:
+		if (!cpu_guest_has_htw && !cpu_guest_has_ldpte)
+			return -EINVAL;
+		write_gc0_pwctl(v);
+		break;
+	case KVM_REG_MIPS_CP0_HWRENA:
+		write_gc0_hwrena(v);
+		break;
+	case KVM_REG_MIPS_CP0_BADVADDR:
+		write_gc0_badvaddr(v);
+		break;
+	case KVM_REG_MIPS_CP0_BADINSTR:
+		if (!cpu_guest_has_badinstr)
+			return -EINVAL;
+		write_gc0_badinstr(v);
+		break;
+	case KVM_REG_MIPS_CP0_BADINSTRP:
+		if (!cpu_guest_has_badinstrp)
+			return -EINVAL;
+		write_gc0_badinstrp(v);
+		break;
+	case KVM_REG_MIPS_CP0_COUNT:
+		kvm_mips_write_count(vcpu, v);
+		break;
+	case KVM_REG_MIPS_CP0_ENTRYHI:
+		write_gc0_entryhi(v);
+		break;
+	case KVM_REG_MIPS_CP0_COMPARE:
+		kvm_mips_write_compare(vcpu, v, false);
+		break;
+	case KVM_REG_MIPS_CP0_STATUS:
+		write_gc0_status(v);
+		break;
+	case KVM_REG_MIPS_CP0_INTCTL:
+		write_gc0_intctl(v);
+		break;
+	case KVM_REG_MIPS_CP0_CAUSE:
+		/*
+		 * If the timer is stopped or started (DC bit) it must look
+		 * atomic with changes to the timer interrupt pending bit (TI).
+		 * A timer interrupt should not happen in between.
+		 */
+		if ((read_gc0_cause() ^ v) & CAUSEF_DC) {
+			if (v & CAUSEF_DC) {
+				/* disable timer first */
+				kvm_mips_count_disable_cause(vcpu);
+				change_gc0_cause((u32)~CAUSEF_DC, v);
+			} else {
+				/* enable timer last */
+				change_gc0_cause((u32)~CAUSEF_DC, v);
+				kvm_mips_count_enable_cause(vcpu);
+			}
+		} else {
+			write_gc0_cause(v);
+		}
+		break;
+	case KVM_REG_MIPS_CP0_EPC:
+		write_gc0_epc(v);
+		break;
+	case KVM_REG_MIPS_CP0_PRID:
+		switch (boot_cpu_type()) {
+		case CPU_CAVIUM_OCTEON3:
+			/* Octeon III has a guest.PRid, but its read-only */
+			break;
+		default:
+			kvm_write_c0_guest_prid(cop0, v);
+			break;
+		}
+		break;
+	case KVM_REG_MIPS_CP0_EBASE:
+		kvm_vz_write_gc0_ebase(v);
+		break;
+	case KVM_REG_MIPS_CP0_CONFIG:
+		cur = read_gc0_config();
+		change = (cur ^ v) & kvm_vz_config_user_wrmask(vcpu);
+		if (change) {
+			v = cur ^ change;
+			write_gc0_config(v);
+		}
+		break;
+	case KVM_REG_MIPS_CP0_CONFIG1:
+		if (!cpu_guest_has_conf1)
+			break;
+		cur = read_gc0_config1();
+		change = (cur ^ v) & kvm_vz_config1_user_wrmask(vcpu);
+		if (change) {
+			v = cur ^ change;
+			write_gc0_config1(v);
+		}
+		break;
+	case KVM_REG_MIPS_CP0_CONFIG2:
+		if (!cpu_guest_has_conf2)
+			break;
+		cur = read_gc0_config2();
+		change = (cur ^ v) & kvm_vz_config2_user_wrmask(vcpu);
+		if (change) {
+			v = cur ^ change;
+			write_gc0_config2(v);
+		}
+		break;
+	case KVM_REG_MIPS_CP0_CONFIG3:
+		if (!cpu_guest_has_conf3)
+			break;
+		cur = read_gc0_config3();
+		change = (cur ^ v) & kvm_vz_config3_user_wrmask(vcpu);
+		if (change) {
+			v = cur ^ change;
+			write_gc0_config3(v);
+		}
+		break;
+	case KVM_REG_MIPS_CP0_CONFIG4:
+		if (!cpu_guest_has_conf4)
+			break;
+		cur = read_gc0_config4();
+		change = (cur ^ v) & kvm_vz_config4_user_wrmask(vcpu);
+		if (change) {
+			v = cur ^ change;
+			write_gc0_config4(v);
+		}
+		break;
+	case KVM_REG_MIPS_CP0_CONFIG5:
+		if (!cpu_guest_has_conf5)
+			break;
+		cur = read_gc0_config5();
+		change = (cur ^ v) & kvm_vz_config5_user_wrmask(vcpu);
+		if (change) {
+			v = cur ^ change;
+			write_gc0_config5(v);
+		}
+		break;
+	case KVM_REG_MIPS_CP0_CONFIG6:
+		cur = kvm_read_sw_gc0_config6(cop0);
+		change = (cur ^ v) & kvm_vz_config6_user_wrmask(vcpu);
+		if (change) {
+			v = cur ^ change;
+			kvm_write_sw_gc0_config6(cop0, (int)v);
+		}
+		break;
+	case KVM_REG_MIPS_CP0_MAAR(0) ... KVM_REG_MIPS_CP0_MAAR(0x3f):
+		if (!cpu_guest_has_maar || cpu_guest_has_dyn_maar)
+			return -EINVAL;
+		idx = reg->id - KVM_REG_MIPS_CP0_MAAR(0);
+		if (idx >= ARRAY_SIZE(vcpu->arch.maar))
+			return -EINVAL;
+		vcpu->arch.maar[idx] = mips_process_maar(dmtc_op, v);
+		break;
+	case KVM_REG_MIPS_CP0_MAARI:
+		if (!cpu_guest_has_maar || cpu_guest_has_dyn_maar)
+			return -EINVAL;
+		kvm_write_maari(vcpu, v);
+		break;
+#ifdef CONFIG_64BIT
+	case KVM_REG_MIPS_CP0_XCONTEXT:
+		write_gc0_xcontext(v);
+		break;
+#endif
+	case KVM_REG_MIPS_CP0_ERROREPC:
+		write_gc0_errorepc(v);
+		break;
+	case KVM_REG_MIPS_CP0_KSCRATCH1 ... KVM_REG_MIPS_CP0_KSCRATCH6:
+		idx = reg->id - KVM_REG_MIPS_CP0_KSCRATCH1 + 2;
+		if (!cpu_guest_has_kscr(idx))
+			return -EINVAL;
+		switch (idx) {
+		case 2:
+			write_gc0_kscratch1(v);
+			break;
+		case 3:
+			write_gc0_kscratch2(v);
+			break;
+		case 4:
+			write_gc0_kscratch3(v);
+			break;
+		case 5:
+			write_gc0_kscratch4(v);
+			break;
+		case 6:
+			write_gc0_kscratch5(v);
+			break;
+		case 7:
+			write_gc0_kscratch6(v);
+			break;
+		}
+		break;
+	case KVM_REG_MIPS_COUNT_CTL:
+		ret = kvm_mips_set_count_ctl(vcpu, v);
+		break;
+	case KVM_REG_MIPS_COUNT_RESUME:
+		ret = kvm_mips_set_count_resume(vcpu, v);
+		break;
+	case KVM_REG_MIPS_COUNT_HZ:
+		ret = kvm_mips_set_count_hz(vcpu, v);
+		break;
+	default:
+		return -EINVAL;
+	}
+	return ret;
+}
+
+#define guestid_cache(cpu)	(cpu_data[cpu].guestid_cache)
+static void kvm_vz_get_new_guestid(unsigned long cpu, struct kvm_vcpu *vcpu)
+{
+	unsigned long guestid = guestid_cache(cpu);
+
+	if (!(++guestid & GUESTID_MASK)) {
+		if (cpu_has_vtag_icache)
+			flush_icache_all();
+
+		if (!guestid)		/* fix version if needed */
+			guestid = GUESTID_FIRST_VERSION;
+
+		++guestid;		/* guestid 0 reserved for root */
+
+		/* start new guestid cycle */
+		kvm_vz_local_flush_roottlb_all_guests();
+		kvm_vz_local_flush_guesttlb_all();
+	}
+
+	guestid_cache(cpu) = guestid;
+}
+
+/* Returns 1 if the guest TLB may be clobbered */
+static int kvm_vz_check_requests(struct kvm_vcpu *vcpu, int cpu)
+{
+	int ret = 0;
+	int i;
+
+	if (!kvm_request_pending(vcpu))
+		return 0;
+
+	if (kvm_check_request(KVM_REQ_TLB_FLUSH, vcpu)) {
+		if (cpu_has_guestid) {
+			/* Drop all GuestIDs for this VCPU */
+			for_each_possible_cpu(i)
+				vcpu->arch.vzguestid[i] = 0;
+			/* This will clobber guest TLB contents too */
+			ret = 1;
+		}
+		/*
+		 * For Root ASID Dealias (RAD) we don't do anything here, but we
+		 * still need the request to ensure we recheck asid_flush_mask.
+		 * We can still return 0 as only the root TLB will be affected
+		 * by a root ASID flush.
+		 */
+	}
+
+	return ret;
+}
+
+static void kvm_vz_vcpu_save_wired(struct kvm_vcpu *vcpu)
+{
+	unsigned int wired = read_gc0_wired();
+	struct kvm_mips_tlb *tlbs;
+	int i;
+
+	/* Expand the wired TLB array if necessary */
+	wired &= MIPSR6_WIRED_WIRED;
+	if (wired > vcpu->arch.wired_tlb_limit) {
+		tlbs = krealloc(vcpu->arch.wired_tlb, wired *
+				sizeof(*vcpu->arch.wired_tlb), GFP_ATOMIC);
+		if (WARN_ON(!tlbs)) {
+			/* Save whatever we can */
+			wired = vcpu->arch.wired_tlb_limit;
+		} else {
+			vcpu->arch.wired_tlb = tlbs;
+			vcpu->arch.wired_tlb_limit = wired;
+		}
+	}
+
+	if (wired)
+		/* Save wired entries from the guest TLB */
+		kvm_vz_save_guesttlb(vcpu->arch.wired_tlb, 0, wired);
+	/* Invalidate any dropped entries since last time */
+	for (i = wired; i < vcpu->arch.wired_tlb_used; ++i) {
+		vcpu->arch.wired_tlb[i].tlb_hi = UNIQUE_GUEST_ENTRYHI(i);
+		vcpu->arch.wired_tlb[i].tlb_lo[0] = 0;
+		vcpu->arch.wired_tlb[i].tlb_lo[1] = 0;
+		vcpu->arch.wired_tlb[i].tlb_mask = 0;
+	}
+	vcpu->arch.wired_tlb_used = wired;
+}
+
+static void kvm_vz_vcpu_load_wired(struct kvm_vcpu *vcpu)
+{
+	/* Load wired entries into the guest TLB */
+	if (vcpu->arch.wired_tlb)
+		kvm_vz_load_guesttlb(vcpu->arch.wired_tlb, 0,
+				     vcpu->arch.wired_tlb_used);
+}
+
+static void kvm_vz_vcpu_load_tlb(struct kvm_vcpu *vcpu, int cpu)
+{
+	struct kvm *kvm = vcpu->kvm;
+	struct mm_struct *gpa_mm = &kvm->arch.gpa_mm;
+	bool migrated;
+
+	/*
+	 * Are we entering guest context on a different CPU to last time?
+	 * If so, the VCPU's guest TLB state on this CPU may be stale.
+	 */
+	migrated = (vcpu->arch.last_exec_cpu != cpu);
+	vcpu->arch.last_exec_cpu = cpu;
+
+	/*
+	 * A vcpu's GuestID is set in GuestCtl1.ID when the vcpu is loaded and
+	 * remains set until another vcpu is loaded in.  As a rule GuestRID
+	 * remains zeroed when in root context unless the kernel is busy
+	 * manipulating guest tlb entries.
+	 */
+	if (cpu_has_guestid) {
+		/*
+		 * Check if our GuestID is of an older version and thus invalid.
+		 *
+		 * We also discard the stored GuestID if we've executed on
+		 * another CPU, as the guest mappings may have changed without
+		 * hypervisor knowledge.
+		 */
+		if (migrated ||
+		    (vcpu->arch.vzguestid[cpu] ^ guestid_cache(cpu)) &
+					GUESTID_VERSION_MASK) {
+			kvm_vz_get_new_guestid(cpu, vcpu);
+			vcpu->arch.vzguestid[cpu] = guestid_cache(cpu);
+			trace_kvm_guestid_change(vcpu,
+						 vcpu->arch.vzguestid[cpu]);
+		}
+
+		/* Restore GuestID */
+		change_c0_guestctl1(GUESTID_MASK, vcpu->arch.vzguestid[cpu]);
+	} else {
+		/*
+		 * The Guest TLB only stores a single guest's TLB state, so
+		 * flush it if another VCPU has executed on this CPU.
+		 *
+		 * We also flush if we've executed on another CPU, as the guest
+		 * mappings may have changed without hypervisor knowledge.
+		 */
+		if (migrated || last_exec_vcpu[cpu] != vcpu)
+			kvm_vz_local_flush_guesttlb_all();
+		last_exec_vcpu[cpu] = vcpu;
+
+		/*
+		 * Root ASID dealiases guest GPA mappings in the root TLB.
+		 * Allocate new root ASID if needed.
+		 */
+		if (cpumask_test_and_clear_cpu(cpu, &kvm->arch.asid_flush_mask))
+			get_new_mmu_context(gpa_mm);
+		else
+			check_mmu_context(gpa_mm);
+	}
+}
+
+static int kvm_vz_vcpu_load(struct kvm_vcpu *vcpu, int cpu)
+{
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
+	bool migrated, all;
+
+	/*
+	 * Have we migrated to a different CPU?
+	 * If so, any old guest TLB state may be stale.
+	 */
+	migrated = (vcpu->arch.last_sched_cpu != cpu);
+
+	/*
+	 * Was this the last VCPU to run on this CPU?
+	 * If not, any old guest state from this VCPU will have been clobbered.
+	 */
+	all = migrated || (last_vcpu[cpu] != vcpu);
+	last_vcpu[cpu] = vcpu;
+
+	/*
+	 * Restore CP0_Wired unconditionally as we clear it after use, and
+	 * restore wired guest TLB entries (while in guest context).
+	 */
+	kvm_restore_gc0_wired(cop0);
+	if (current->flags & PF_VCPU) {
+		tlbw_use_hazard();
+		kvm_vz_vcpu_load_tlb(vcpu, cpu);
+		kvm_vz_vcpu_load_wired(vcpu);
+	}
+
+	/*
+	 * Restore timer state regardless, as e.g. Cause.TI can change over time
+	 * if left unmaintained.
+	 */
+	kvm_vz_restore_timer(vcpu);
+
+	/* Set MC bit if we want to trace guest mode changes */
+	if (kvm_trace_guest_mode_change)
+		set_c0_guestctl0(MIPS_GCTL0_MC);
+	else
+		clear_c0_guestctl0(MIPS_GCTL0_MC);
+
+	/* Don't bother restoring registers multiple times unless necessary */
+	if (!all)
+		return 0;
+
+	/*
+	 * Restore config registers first, as some implementations restrict
+	 * writes to other registers when the corresponding feature bits aren't
+	 * set. For example Status.CU1 cannot be set unless Config1.FP is set.
+	 */
+	kvm_restore_gc0_config(cop0);
+	if (cpu_guest_has_conf1)
+		kvm_restore_gc0_config1(cop0);
+	if (cpu_guest_has_conf2)
+		kvm_restore_gc0_config2(cop0);
+	if (cpu_guest_has_conf3)
+		kvm_restore_gc0_config3(cop0);
+	if (cpu_guest_has_conf4)
+		kvm_restore_gc0_config4(cop0);
+	if (cpu_guest_has_conf5)
+		kvm_restore_gc0_config5(cop0);
+	if (cpu_guest_has_conf6)
+		kvm_restore_gc0_config6(cop0);
+	if (cpu_guest_has_conf7)
+		kvm_restore_gc0_config7(cop0);
+
+	kvm_restore_gc0_index(cop0);
+	kvm_restore_gc0_entrylo0(cop0);
+	kvm_restore_gc0_entrylo1(cop0);
+	kvm_restore_gc0_context(cop0);
+	if (cpu_guest_has_contextconfig)
+		kvm_restore_gc0_contextconfig(cop0);
+#ifdef CONFIG_64BIT
+	kvm_restore_gc0_xcontext(cop0);
+	if (cpu_guest_has_contextconfig)
+		kvm_restore_gc0_xcontextconfig(cop0);
+#endif
+	kvm_restore_gc0_pagemask(cop0);
+	kvm_restore_gc0_pagegrain(cop0);
+	kvm_restore_gc0_hwrena(cop0);
+	kvm_restore_gc0_badvaddr(cop0);
+	kvm_restore_gc0_entryhi(cop0);
+	kvm_restore_gc0_status(cop0);
+	kvm_restore_gc0_intctl(cop0);
+	kvm_restore_gc0_epc(cop0);
+	kvm_vz_write_gc0_ebase(kvm_read_sw_gc0_ebase(cop0));
+	if (cpu_guest_has_userlocal)
+		kvm_restore_gc0_userlocal(cop0);
+
+	kvm_restore_gc0_errorepc(cop0);
+
+	/* restore KScratch registers if enabled in guest */
+	if (cpu_guest_has_conf4) {
+		if (cpu_guest_has_kscr(2))
+			kvm_restore_gc0_kscratch1(cop0);
+		if (cpu_guest_has_kscr(3))
+			kvm_restore_gc0_kscratch2(cop0);
+		if (cpu_guest_has_kscr(4))
+			kvm_restore_gc0_kscratch3(cop0);
+		if (cpu_guest_has_kscr(5))
+			kvm_restore_gc0_kscratch4(cop0);
+		if (cpu_guest_has_kscr(6))
+			kvm_restore_gc0_kscratch5(cop0);
+		if (cpu_guest_has_kscr(7))
+			kvm_restore_gc0_kscratch6(cop0);
+	}
+
+	if (cpu_guest_has_badinstr)
+		kvm_restore_gc0_badinstr(cop0);
+	if (cpu_guest_has_badinstrp)
+		kvm_restore_gc0_badinstrp(cop0);
+
+	if (cpu_guest_has_segments) {
+		kvm_restore_gc0_segctl0(cop0);
+		kvm_restore_gc0_segctl1(cop0);
+		kvm_restore_gc0_segctl2(cop0);
+	}
+
+	/* restore HTW registers */
+	if (cpu_guest_has_htw || cpu_guest_has_ldpte) {
+		kvm_restore_gc0_pwbase(cop0);
+		kvm_restore_gc0_pwfield(cop0);
+		kvm_restore_gc0_pwsize(cop0);
+		kvm_restore_gc0_pwctl(cop0);
+	}
+
+	/* restore Root.GuestCtl2 from unused Guest guestctl2 register */
+	if (cpu_has_guestctl2)
+		write_c0_guestctl2(
+			cop0->reg[MIPS_CP0_GUESTCTL2][MIPS_CP0_GUESTCTL2_SEL]);
+
+	/*
+	 * We should clear linked load bit to break interrupted atomics. This
+	 * prevents a SC on the next VCPU from succeeding by matching a LL on
+	 * the previous VCPU.
+	 */
+	if (vcpu->kvm->created_vcpus > 1)
+		write_gc0_lladdr(0);
+
+	return 0;
+}
+
+static int kvm_vz_vcpu_put(struct kvm_vcpu *vcpu, int cpu)
+{
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
+
+	if (current->flags & PF_VCPU)
+		kvm_vz_vcpu_save_wired(vcpu);
+
+	kvm_lose_fpu(vcpu);
+
+	kvm_save_gc0_index(cop0);
+	kvm_save_gc0_entrylo0(cop0);
+	kvm_save_gc0_entrylo1(cop0);
+	kvm_save_gc0_context(cop0);
+	if (cpu_guest_has_contextconfig)
+		kvm_save_gc0_contextconfig(cop0);
+#ifdef CONFIG_64BIT
+	kvm_save_gc0_xcontext(cop0);
+	if (cpu_guest_has_contextconfig)
+		kvm_save_gc0_xcontextconfig(cop0);
+#endif
+	kvm_save_gc0_pagemask(cop0);
+	kvm_save_gc0_pagegrain(cop0);
+	kvm_save_gc0_wired(cop0);
+	/* allow wired TLB entries to be overwritten */
+	clear_gc0_wired(MIPSR6_WIRED_WIRED);
+	kvm_save_gc0_hwrena(cop0);
+	kvm_save_gc0_badvaddr(cop0);
+	kvm_save_gc0_entryhi(cop0);
+	kvm_save_gc0_status(cop0);
+	kvm_save_gc0_intctl(cop0);
+	kvm_save_gc0_epc(cop0);
+	kvm_write_sw_gc0_ebase(cop0, kvm_vz_read_gc0_ebase());
+	if (cpu_guest_has_userlocal)
+		kvm_save_gc0_userlocal(cop0);
+
+	/* only save implemented config registers */
+	kvm_save_gc0_config(cop0);
+	if (cpu_guest_has_conf1)
+		kvm_save_gc0_config1(cop0);
+	if (cpu_guest_has_conf2)
+		kvm_save_gc0_config2(cop0);
+	if (cpu_guest_has_conf3)
+		kvm_save_gc0_config3(cop0);
+	if (cpu_guest_has_conf4)
+		kvm_save_gc0_config4(cop0);
+	if (cpu_guest_has_conf5)
+		kvm_save_gc0_config5(cop0);
+	if (cpu_guest_has_conf6)
+		kvm_save_gc0_config6(cop0);
+	if (cpu_guest_has_conf7)
+		kvm_save_gc0_config7(cop0);
+
+	kvm_save_gc0_errorepc(cop0);
+
+	/* save KScratch registers if enabled in guest */
+	if (cpu_guest_has_conf4) {
+		if (cpu_guest_has_kscr(2))
+			kvm_save_gc0_kscratch1(cop0);
+		if (cpu_guest_has_kscr(3))
+			kvm_save_gc0_kscratch2(cop0);
+		if (cpu_guest_has_kscr(4))
+			kvm_save_gc0_kscratch3(cop0);
+		if (cpu_guest_has_kscr(5))
+			kvm_save_gc0_kscratch4(cop0);
+		if (cpu_guest_has_kscr(6))
+			kvm_save_gc0_kscratch5(cop0);
+		if (cpu_guest_has_kscr(7))
+			kvm_save_gc0_kscratch6(cop0);
+	}
+
+	if (cpu_guest_has_badinstr)
+		kvm_save_gc0_badinstr(cop0);
+	if (cpu_guest_has_badinstrp)
+		kvm_save_gc0_badinstrp(cop0);
+
+	if (cpu_guest_has_segments) {
+		kvm_save_gc0_segctl0(cop0);
+		kvm_save_gc0_segctl1(cop0);
+		kvm_save_gc0_segctl2(cop0);
+	}
+
+	/* save HTW registers if enabled in guest */
+	if (cpu_guest_has_ldpte || (cpu_guest_has_htw &&
+	    kvm_read_sw_gc0_config3(cop0) & MIPS_CONF3_PW)) {
+		kvm_save_gc0_pwbase(cop0);
+		kvm_save_gc0_pwfield(cop0);
+		kvm_save_gc0_pwsize(cop0);
+		kvm_save_gc0_pwctl(cop0);
+	}
+
+	kvm_vz_save_timer(vcpu);
+
+	/* save Root.GuestCtl2 in unused Guest guestctl2 register */
+	if (cpu_has_guestctl2)
+		cop0->reg[MIPS_CP0_GUESTCTL2][MIPS_CP0_GUESTCTL2_SEL] =
+			read_c0_guestctl2();
+
+	return 0;
+}
+
+/**
+ * kvm_vz_resize_guest_vtlb() - Attempt to resize guest VTLB.
+ * @size:	Number of guest VTLB entries (0 < @size <= root VTLB entries).
+ *
+ * Attempt to resize the guest VTLB by writing guest Config registers. This is
+ * necessary for cores with a shared root/guest TLB to avoid overlap with wired
+ * entries in the root VTLB.
+ *
+ * Returns:	The resulting guest VTLB size.
+ */
+static unsigned int kvm_vz_resize_guest_vtlb(unsigned int size)
+{
+	unsigned int config4 = 0, ret = 0, limit;
+
+	/* Write MMUSize - 1 into guest Config registers */
+	if (cpu_guest_has_conf1)
+		change_gc0_config1(MIPS_CONF1_TLBS,
+				   (size - 1) << MIPS_CONF1_TLBS_SHIFT);
+	if (cpu_guest_has_conf4) {
+		config4 = read_gc0_config4();
+		if (cpu_has_mips_r6 || (config4 & MIPS_CONF4_MMUEXTDEF) ==
+		    MIPS_CONF4_MMUEXTDEF_VTLBSIZEEXT) {
+			config4 &= ~MIPS_CONF4_VTLBSIZEEXT;
+			config4 |= ((size - 1) >> MIPS_CONF1_TLBS_SIZE) <<
+				MIPS_CONF4_VTLBSIZEEXT_SHIFT;
+		} else if ((config4 & MIPS_CONF4_MMUEXTDEF) ==
+			   MIPS_CONF4_MMUEXTDEF_MMUSIZEEXT) {
+			config4 &= ~MIPS_CONF4_MMUSIZEEXT;
+			config4 |= ((size - 1) >> MIPS_CONF1_TLBS_SIZE) <<
+				MIPS_CONF4_MMUSIZEEXT_SHIFT;
+		}
+		write_gc0_config4(config4);
+	}
+
+	/*
+	 * Set Guest.Wired.Limit = 0 (no limit up to Guest.MMUSize-1), unless it
+	 * would exceed Root.Wired.Limit (clearing Guest.Wired.Wired so write
+	 * not dropped)
+	 */
+	if (cpu_has_mips_r6) {
+		limit = (read_c0_wired() & MIPSR6_WIRED_LIMIT) >>
+						MIPSR6_WIRED_LIMIT_SHIFT;
+		if (size - 1 <= limit)
+			limit = 0;
+		write_gc0_wired(limit << MIPSR6_WIRED_LIMIT_SHIFT);
+	}
+
+	/* Read back MMUSize - 1 */
+	back_to_back_c0_hazard();
+	if (cpu_guest_has_conf1)
+		ret = (read_gc0_config1() & MIPS_CONF1_TLBS) >>
+						MIPS_CONF1_TLBS_SHIFT;
+	if (config4) {
+		if (cpu_has_mips_r6 || (config4 & MIPS_CONF4_MMUEXTDEF) ==
+		    MIPS_CONF4_MMUEXTDEF_VTLBSIZEEXT)
+			ret |= ((config4 & MIPS_CONF4_VTLBSIZEEXT) >>
+				MIPS_CONF4_VTLBSIZEEXT_SHIFT) <<
+				MIPS_CONF1_TLBS_SIZE;
+		else if ((config4 & MIPS_CONF4_MMUEXTDEF) ==
+			 MIPS_CONF4_MMUEXTDEF_MMUSIZEEXT)
+			ret |= ((config4 & MIPS_CONF4_MMUSIZEEXT) >>
+				MIPS_CONF4_MMUSIZEEXT_SHIFT) <<
+				MIPS_CONF1_TLBS_SIZE;
+	}
+	return ret + 1;
+}
+
+static int kvm_vz_hardware_enable(void)
+{
+	unsigned int mmu_size, guest_mmu_size, ftlb_size;
+	u64 guest_cvmctl, cvmvmconfig;
+
+	switch (current_cpu_type()) {
+	case CPU_CAVIUM_OCTEON3:
+		/* Set up guest timer/perfcount IRQ lines */
+		guest_cvmctl = read_gc0_cvmctl();
+		guest_cvmctl &= ~CVMCTL_IPTI;
+		guest_cvmctl |= 7ull << CVMCTL_IPTI_SHIFT;
+		guest_cvmctl &= ~CVMCTL_IPPCI;
+		guest_cvmctl |= 6ull << CVMCTL_IPPCI_SHIFT;
+		write_gc0_cvmctl(guest_cvmctl);
+
+		cvmvmconfig = read_c0_cvmvmconfig();
+		/* No I/O hole translation. */
+		cvmvmconfig |= CVMVMCONF_DGHT;
+		/* Halve the root MMU size */
+		mmu_size = ((cvmvmconfig & CVMVMCONF_MMUSIZEM1)
+			    >> CVMVMCONF_MMUSIZEM1_S) + 1;
+		guest_mmu_size = mmu_size / 2;
+		mmu_size -= guest_mmu_size;
+		cvmvmconfig &= ~CVMVMCONF_RMMUSIZEM1;
+		cvmvmconfig |= mmu_size - 1;
+		write_c0_cvmvmconfig(cvmvmconfig);
+
+		/* Update our records */
+		current_cpu_data.tlbsize = mmu_size;
+		current_cpu_data.tlbsizevtlb = mmu_size;
+		current_cpu_data.guest.tlbsize = guest_mmu_size;
+
+		/* Flush moved entries in new (guest) context */
+		kvm_vz_local_flush_guesttlb_all();
+		break;
+	default:
+		/*
+		 * ImgTec cores tend to use a shared root/guest TLB. To avoid
+		 * overlap of root wired and guest entries, the guest TLB may
+		 * need resizing.
+		 */
+		mmu_size = current_cpu_data.tlbsizevtlb;
+		ftlb_size = current_cpu_data.tlbsize - mmu_size;
+
+		/* Try switching to maximum guest VTLB size for flush */
+		guest_mmu_size = kvm_vz_resize_guest_vtlb(mmu_size);
+		current_cpu_data.guest.tlbsize = guest_mmu_size + ftlb_size;
+		kvm_vz_local_flush_guesttlb_all();
+
+		/*
+		 * Reduce to make space for root wired entries and at least 2
+		 * root non-wired entries. This does assume that long-term wired
+		 * entries won't be added later.
+		 */
+		guest_mmu_size = mmu_size - num_wired_entries() - 2;
+		guest_mmu_size = kvm_vz_resize_guest_vtlb(guest_mmu_size);
+		current_cpu_data.guest.tlbsize = guest_mmu_size + ftlb_size;
+
+		/*
+		 * Write the VTLB size, but if another CPU has already written,
+		 * check it matches or we won't provide a consistent view to the
+		 * guest. If this ever happens it suggests an asymmetric number
+		 * of wired entries.
+		 */
+		if (cmpxchg(&kvm_vz_guest_vtlb_size, 0, guest_mmu_size) &&
+		    WARN(guest_mmu_size != kvm_vz_guest_vtlb_size,
+			 "Available guest VTLB size mismatch"))
+			return -EINVAL;
+		break;
+	}
+
+	/*
+	 * Enable virtualization features granting guest direct control of
+	 * certain features:
+	 * CP0=1:	Guest coprocessor 0 context.
+	 * AT=Guest:	Guest MMU.
+	 * CG=1:	Hit (virtual address) CACHE operations (optional).
+	 * CF=1:	Guest Config registers.
+	 * CGI=1:	Indexed flush CACHE operations (optional).
+	 */
+	write_c0_guestctl0(MIPS_GCTL0_CP0 |
+			   (MIPS_GCTL0_AT_GUEST << MIPS_GCTL0_AT_SHIFT) |
+			   MIPS_GCTL0_CG | MIPS_GCTL0_CF);
+	if (cpu_has_guestctl0ext) {
+		if (current_cpu_type() != CPU_LOONGSON64)
+			set_c0_guestctl0ext(MIPS_GCTL0EXT_CGI);
+		else
+			clear_c0_guestctl0ext(MIPS_GCTL0EXT_CGI);
+	}
+
+	if (cpu_has_guestid) {
+		write_c0_guestctl1(0);
+		kvm_vz_local_flush_roottlb_all_guests();
+
+		GUESTID_MASK = current_cpu_data.guestid_mask;
+		GUESTID_FIRST_VERSION = GUESTID_MASK + 1;
+		GUESTID_VERSION_MASK = ~GUESTID_MASK;
+
+		current_cpu_data.guestid_cache = GUESTID_FIRST_VERSION;
+	}
+
+	/* clear any pending injected virtual guest interrupts */
+	if (cpu_has_guestctl2)
+		clear_c0_guestctl2(0x3f << 10);
+
+#ifdef CONFIG_CPU_LOONGSON64
+	/* Control guest CCA attribute */
+	if (cpu_has_csr())
+		csr_writel(csr_readl(0xffffffec) | 0x1, 0xffffffec);
+#endif
+
+	return 0;
+}
+
+static void kvm_vz_hardware_disable(void)
+{
+	u64 cvmvmconfig;
+	unsigned int mmu_size;
+
+	/* Flush any remaining guest TLB entries */
+	kvm_vz_local_flush_guesttlb_all();
+
+	switch (current_cpu_type()) {
+	case CPU_CAVIUM_OCTEON3:
+		/*
+		 * Allocate whole TLB for root. Existing guest TLB entries will
+		 * change ownership to the root TLB. We should be safe though as
+		 * they've already been flushed above while in guest TLB.
+		 */
+		cvmvmconfig = read_c0_cvmvmconfig();
+		mmu_size = ((cvmvmconfig & CVMVMCONF_MMUSIZEM1)
+			    >> CVMVMCONF_MMUSIZEM1_S) + 1;
+		cvmvmconfig &= ~CVMVMCONF_RMMUSIZEM1;
+		cvmvmconfig |= mmu_size - 1;
+		write_c0_cvmvmconfig(cvmvmconfig);
+
+		/* Update our records */
+		current_cpu_data.tlbsize = mmu_size;
+		current_cpu_data.tlbsizevtlb = mmu_size;
+		current_cpu_data.guest.tlbsize = 0;
+
+		/* Flush moved entries in new (root) context */
+		local_flush_tlb_all();
+		break;
+	}
+
+	if (cpu_has_guestid) {
+		write_c0_guestctl1(0);
+		kvm_vz_local_flush_roottlb_all_guests();
+	}
+}
+
+static int kvm_vz_check_extension(struct kvm *kvm, long ext)
+{
+	int r;
+
+	switch (ext) {
+	case KVM_CAP_MIPS_VZ:
+		/* we wouldn't be here unless cpu_has_vz */
+		r = 1;
+		break;
+#ifdef CONFIG_64BIT
+	case KVM_CAP_MIPS_64BIT:
+		/* We support 64-bit registers/operations and addresses */
+		r = 2;
+		break;
+#endif
+	case KVM_CAP_IOEVENTFD:
+		r = 1;
+		break;
+	default:
+		r = 0;
+		break;
+	}
+
+	return r;
+}
+
+static int kvm_vz_vcpu_init(struct kvm_vcpu *vcpu)
+{
+	int i;
+
+	for_each_possible_cpu(i)
+		vcpu->arch.vzguestid[i] = 0;
+
+	return 0;
+}
+
+static void kvm_vz_vcpu_uninit(struct kvm_vcpu *vcpu)
+{
+	int cpu;
+
+	/*
+	 * If the VCPU is freed and reused as another VCPU, we don't want the
+	 * matching pointer wrongly hanging around in last_vcpu[] or
+	 * last_exec_vcpu[].
+	 */
+	for_each_possible_cpu(cpu) {
+		if (last_vcpu[cpu] == vcpu)
+			last_vcpu[cpu] = NULL;
+		if (last_exec_vcpu[cpu] == vcpu)
+			last_exec_vcpu[cpu] = NULL;
+	}
+}
+
+static int kvm_vz_vcpu_setup(struct kvm_vcpu *vcpu)
+{
+	struct mips_coproc *cop0 = &vcpu->arch.cop0;
+	unsigned long count_hz = 100*1000*1000; /* default to 100 MHz */
+
+	/*
+	 * Start off the timer at the same frequency as the host timer, but the
+	 * soft timer doesn't handle frequencies greater than 1GHz yet.
+	 */
+	if (mips_hpt_frequency && mips_hpt_frequency <= NSEC_PER_SEC)
+		count_hz = mips_hpt_frequency;
+	kvm_mips_init_count(vcpu, count_hz);
+
+	/*
+	 * Initialize guest register state to valid architectural reset state.
+	 */
+
+	/* PageGrain */
+	if (cpu_has_mips_r5 || cpu_has_mips_r6)
+		kvm_write_sw_gc0_pagegrain(cop0, PG_RIE | PG_XIE | PG_IEC);
+	/* Wired */
+	if (cpu_has_mips_r6)
+		kvm_write_sw_gc0_wired(cop0,
+				       read_gc0_wired() & MIPSR6_WIRED_LIMIT);
+	/* Status */
+	kvm_write_sw_gc0_status(cop0, ST0_BEV | ST0_ERL);
+	if (cpu_has_mips_r5 || cpu_has_mips_r6)
+		kvm_change_sw_gc0_status(cop0, ST0_FR, read_gc0_status());
+	/* IntCtl */
+	kvm_write_sw_gc0_intctl(cop0, read_gc0_intctl() &
+				(INTCTLF_IPFDC | INTCTLF_IPPCI | INTCTLF_IPTI));
+	/* PRId */
+	kvm_write_sw_gc0_prid(cop0, boot_cpu_data.processor_id);
+	/* EBase */
+	kvm_write_sw_gc0_ebase(cop0, (s32)0x80000000 | vcpu->vcpu_id);
+	/* Config */
+	kvm_save_gc0_config(cop0);
+	/* architecturally writable (e.g. from guest) */
+	kvm_change_sw_gc0_config(cop0, CONF_CM_CMASK,
+				 _page_cachable_default >> _CACHE_SHIFT);
+	/* architecturally read only, but maybe writable from root */
+	kvm_change_sw_gc0_config(cop0, MIPS_CONF_MT, read_c0_config());
+	if (cpu_guest_has_conf1) {
+		kvm_set_sw_gc0_config(cop0, MIPS_CONF_M);
+		/* Config1 */
+		kvm_save_gc0_config1(cop0);
+		/* architecturally read only, but maybe writable from root */
+		kvm_clear_sw_gc0_config1(cop0, MIPS_CONF1_C2	|
+					       MIPS_CONF1_MD	|
+					       MIPS_CONF1_PC	|
+					       MIPS_CONF1_WR	|
+					       MIPS_CONF1_CA	|
+					       MIPS_CONF1_FP);
+	}
+	if (cpu_guest_has_conf2) {
+		kvm_set_sw_gc0_config1(cop0, MIPS_CONF_M);
+		/* Config2 */
+		kvm_save_gc0_config2(cop0);
+	}
+	if (cpu_guest_has_conf3) {
+		kvm_set_sw_gc0_config2(cop0, MIPS_CONF_M);
+		/* Config3 */
+		kvm_save_gc0_config3(cop0);
+		/* architecturally writable (e.g. from guest) */
+		kvm_clear_sw_gc0_config3(cop0, MIPS_CONF3_ISA_OE);
+		/* architecturally read only, but maybe writable from root */
+		kvm_clear_sw_gc0_config3(cop0, MIPS_CONF3_MSA	|
+					       MIPS_CONF3_BPG	|
+					       MIPS_CONF3_ULRI	|
+					       MIPS_CONF3_DSP	|
+					       MIPS_CONF3_CTXTC	|
+					       MIPS_CONF3_ITL	|
+					       MIPS_CONF3_LPA	|
+					       MIPS_CONF3_VEIC	|
+					       MIPS_CONF3_VINT	|
+					       MIPS_CONF3_SP	|
+					       MIPS_CONF3_CDMM	|
+					       MIPS_CONF3_MT	|
+					       MIPS_CONF3_SM	|
+					       MIPS_CONF3_TL);
+	}
+	if (cpu_guest_has_conf4) {
+		kvm_set_sw_gc0_config3(cop0, MIPS_CONF_M);
+		/* Config4 */
+		kvm_save_gc0_config4(cop0);
+	}
+	if (cpu_guest_has_conf5) {
+		kvm_set_sw_gc0_config4(cop0, MIPS_CONF_M);
+		/* Config5 */
+		kvm_save_gc0_config5(cop0);
+		/* architecturally writable (e.g. from guest) */
+		kvm_clear_sw_gc0_config5(cop0, MIPS_CONF5_K	|
+					       MIPS_CONF5_CV	|
+					       MIPS_CONF5_MSAEN	|
+					       MIPS_CONF5_UFE	|
+					       MIPS_CONF5_FRE	|
+					       MIPS_CONF5_SBRI	|
+					       MIPS_CONF5_UFR);
+		/* architecturally read only, but maybe writable from root */
+		kvm_clear_sw_gc0_config5(cop0, MIPS_CONF5_MRP);
+	}
+
+	if (cpu_guest_has_contextconfig) {
+		/* ContextConfig */
+		kvm_write_sw_gc0_contextconfig(cop0, 0x007ffff0);
+#ifdef CONFIG_64BIT
+		/* XContextConfig */
+		/* bits SEGBITS-13+3:4 set */
+		kvm_write_sw_gc0_xcontextconfig(cop0,
+					((1ull << (cpu_vmbits - 13)) - 1) << 4);
+#endif
+	}
+
+	/* Implementation dependent, use the legacy layout */
+	if (cpu_guest_has_segments) {
+		/* SegCtl0, SegCtl1, SegCtl2 */
+		kvm_write_sw_gc0_segctl0(cop0, 0x00200010);
+		kvm_write_sw_gc0_segctl1(cop0, 0x00000002 |
+				(_page_cachable_default >> _CACHE_SHIFT) <<
+						(16 + MIPS_SEGCFG_C_SHIFT));
+		kvm_write_sw_gc0_segctl2(cop0, 0x00380438);
+	}
+
+	/* reset HTW registers */
+	if (cpu_guest_has_htw && (cpu_has_mips_r5 || cpu_has_mips_r6)) {
+		/* PWField */
+		kvm_write_sw_gc0_pwfield(cop0, 0x0c30c302);
+		/* PWSize */
+		kvm_write_sw_gc0_pwsize(cop0, 1 << MIPS_PWSIZE_PTW_SHIFT);
+	}
+
+	/* start with no pending virtual guest interrupts */
+	if (cpu_has_guestctl2)
+		cop0->reg[MIPS_CP0_GUESTCTL2][MIPS_CP0_GUESTCTL2_SEL] = 0;
+
+	/* Put PC at reset vector */
+	vcpu->arch.pc = CKSEG1ADDR(0x1fc00000);
+
+	return 0;
+}
+
+static void kvm_vz_prepare_flush_shadow(struct kvm *kvm)
+{
+	if (!cpu_has_guestid) {
+		/*
+		 * For each CPU there is a single GPA ASID used by all VCPUs in
+		 * the VM, so it doesn't make sense for the VCPUs to handle
+		 * invalidation of these ASIDs individually.
+		 *
+		 * Instead mark all CPUs as needing ASID invalidation in
+		 * asid_flush_mask, and kvm_flush_remote_tlbs(kvm) will
+		 * kick any running VCPUs so they check asid_flush_mask.
+		 */
+		cpumask_setall(&kvm->arch.asid_flush_mask);
+	}
+}
+
+static void kvm_vz_vcpu_reenter(struct kvm_vcpu *vcpu)
+{
+	int cpu = smp_processor_id();
+	int preserve_guest_tlb;
+
+	preserve_guest_tlb = kvm_vz_check_requests(vcpu, cpu);
+
+	if (preserve_guest_tlb)
+		kvm_vz_vcpu_save_wired(vcpu);
+
+	kvm_vz_vcpu_load_tlb(vcpu, cpu);
+
+	if (preserve_guest_tlb)
+		kvm_vz_vcpu_load_wired(vcpu);
+}
+
+static int kvm_vz_vcpu_run(struct kvm_vcpu *vcpu)
+{
+	int cpu = smp_processor_id();
+	int r;
+
+	kvm_vz_acquire_htimer(vcpu);
+	/* Check if we have any exceptions/interrupts pending */
+	kvm_mips_deliver_interrupts(vcpu, read_gc0_cause());
+
+	kvm_vz_check_requests(vcpu, cpu);
+	kvm_vz_vcpu_load_tlb(vcpu, cpu);
+	kvm_vz_vcpu_load_wired(vcpu);
+
+	r = vcpu->arch.vcpu_run(vcpu);
+
+	kvm_vz_vcpu_save_wired(vcpu);
+
+	return r;
+}
+
+static struct kvm_mips_callbacks kvm_vz_callbacks = {
+	.handle_cop_unusable = kvm_trap_vz_handle_cop_unusable,
+	.handle_tlb_mod = kvm_trap_vz_handle_tlb_st_miss,
+	.handle_tlb_ld_miss = kvm_trap_vz_handle_tlb_ld_miss,
+	.handle_tlb_st_miss = kvm_trap_vz_handle_tlb_st_miss,
+	.handle_addr_err_st = kvm_trap_vz_no_handler,
+	.handle_addr_err_ld = kvm_trap_vz_no_handler,
+	.handle_syscall = kvm_trap_vz_no_handler,
+	.handle_res_inst = kvm_trap_vz_no_handler,
+	.handle_break = kvm_trap_vz_no_handler,
+	.handle_msa_disabled = kvm_trap_vz_handle_msa_disabled,
+	.handle_guest_exit = kvm_trap_vz_handle_guest_exit,
+
+	.hardware_enable = kvm_vz_hardware_enable,
+	.hardware_disable = kvm_vz_hardware_disable,
+	.check_extension = kvm_vz_check_extension,
+	.vcpu_init = kvm_vz_vcpu_init,
+	.vcpu_uninit = kvm_vz_vcpu_uninit,
+	.vcpu_setup = kvm_vz_vcpu_setup,
+	.prepare_flush_shadow = kvm_vz_prepare_flush_shadow,
+	.gva_to_gpa = kvm_vz_gva_to_gpa_cb,
+	.queue_timer_int = kvm_vz_queue_timer_int_cb,
+	.dequeue_timer_int = kvm_vz_dequeue_timer_int_cb,
+	.queue_io_int = kvm_vz_queue_io_int_cb,
+	.dequeue_io_int = kvm_vz_dequeue_io_int_cb,
+	.irq_deliver = kvm_vz_irq_deliver_cb,
+	.irq_clear = kvm_vz_irq_clear_cb,
+	.num_regs = kvm_vz_num_regs,
+	.copy_reg_indices = kvm_vz_copy_reg_indices,
+	.get_one_reg = kvm_vz_get_one_reg,
+	.set_one_reg = kvm_vz_set_one_reg,
+	.vcpu_load = kvm_vz_vcpu_load,
+	.vcpu_put = kvm_vz_vcpu_put,
+	.vcpu_run = kvm_vz_vcpu_run,
+	.vcpu_reenter = kvm_vz_vcpu_reenter,
+};
+
+int kvm_mips_emulation_init(struct kvm_mips_callbacks **install_callbacks)
+{
+	if (!cpu_has_vz)
+		return -ENODEV;
+
+	/*
+	 * VZ requires at least 2 KScratch registers, so it should have been
+	 * possible to allocate pgd_reg.
+	 */
+	if (WARN(pgd_reg == -1,
+		 "pgd_reg not allocated even though cpu_has_vz\n"))
+		return -ENODEV;
+
+	pr_info("Starting KVM with MIPS VZ extensions\n");
+
+	*install_callbacks = &kvm_vz_callbacks;
+	return 0;
+}
diff --git a/arch/mips/lantiq/Kconfig b/arch/mips/lantiq/Kconfig
new file mode 100644
index 000000000..6c6802e48
--- /dev/null
+++ b/arch/mips/lantiq/Kconfig
@@ -0,0 +1,55 @@
+# SPDX-License-Identifier: GPL-2.0
+if LANTIQ
+
+config SOC_TYPE_XWAY
+	bool
+	select PINCTRL_XWAY
+	default n
+
+choice
+	prompt "SoC Type"
+	default SOC_XWAY
+
+config SOC_AMAZON_SE
+	bool "Amazon SE"
+	select SOC_TYPE_XWAY
+	select MFD_SYSCON
+	select MFD_CORE
+
+config SOC_XWAY
+	bool "XWAY"
+	select SOC_TYPE_XWAY
+	select HAVE_PCI
+	select MFD_SYSCON
+	select MFD_CORE
+
+config SOC_FALCON
+	bool "FALCON"
+	select PINCTRL_FALCON
+
+endchoice
+
+choice
+	prompt "Built-in device tree"
+	help
+	  Legacy bootloaders do not pass a DTB pointer to the kernel, so
+	  if a "wrapper" is not being used, the kernel will need to include
+	  a device tree that matches the target board.
+
+	  The builtin DTB will only be used if the firmware does not supply
+	  a valid DTB.
+
+config LANTIQ_DT_NONE
+	bool "None"
+
+config DT_EASY50712
+	bool "Easy50712"
+	depends on SOC_XWAY
+	select BUILTIN_DTB
+endchoice
+
+config PCI_LANTIQ
+	bool "PCI Support"
+	depends on SOC_XWAY && PCI
+
+endif
diff --git a/arch/mips/lantiq/Makefile b/arch/mips/lantiq/Makefile
new file mode 100644
index 000000000..e7234ca09
--- /dev/null
+++ b/arch/mips/lantiq/Makefile
@@ -0,0 +1,10 @@
+# SPDX-License-Identifier: GPL-2.0-only
+# Copyright (C) 2010 John Crispin <john@phrozen.org>
+#
+
+obj-y := irq.o clk.o prom.o
+
+obj-$(CONFIG_EARLY_PRINTK) += early_printk.o
+
+obj-$(CONFIG_SOC_TYPE_XWAY) += xway/
+obj-$(CONFIG_SOC_FALCON) += falcon/
diff --git a/arch/mips/lantiq/Platform b/arch/mips/lantiq/Platform
new file mode 100644
index 000000000..0bc9c0fbd
--- /dev/null
+++ b/arch/mips/lantiq/Platform
@@ -0,0 +1,8 @@
+#
+# Lantiq
+#
+
+cflags-$(CONFIG_LANTIQ)		+= -I$(srctree)/arch/mips/include/asm/mach-lantiq
+load-$(CONFIG_LANTIQ)		= 0xffffffff80002000
+cflags-$(CONFIG_SOC_TYPE_XWAY)	+= -I$(srctree)/arch/mips/include/asm/mach-lantiq/xway
+cflags-$(CONFIG_SOC_FALCON)	+= -I$(srctree)/arch/mips/include/asm/mach-lantiq/falcon
diff --git a/arch/mips/lantiq/clk.c b/arch/mips/lantiq/clk.c
new file mode 100644
index 000000000..2d5a0bcb0
--- /dev/null
+++ b/arch/mips/lantiq/clk.c
@@ -0,0 +1,201 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ * Copyright (C) 2010 Thomas Langer <thomas.langer@lantiq.com>
+ * Copyright (C) 2010 John Crispin <john@phrozen.org>
+ */
+#include <linux/io.h>
+#include <linux/export.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/clk.h>
+#include <linux/clkdev.h>
+#include <linux/err.h>
+#include <linux/list.h>
+
+#include <asm/time.h>
+#include <asm/irq.h>
+#include <asm/div64.h>
+
+#include <lantiq_soc.h>
+
+#include "clk.h"
+#include "prom.h"
+
+/* lantiq socs have 3 static clocks */
+static struct clk cpu_clk_generic[4];
+
+void clkdev_add_static(unsigned long cpu, unsigned long fpi,
+			unsigned long io, unsigned long ppe)
+{
+	cpu_clk_generic[0].rate = cpu;
+	cpu_clk_generic[1].rate = fpi;
+	cpu_clk_generic[2].rate = io;
+	cpu_clk_generic[3].rate = ppe;
+}
+
+struct clk *clk_get_cpu(void)
+{
+	return &cpu_clk_generic[0];
+}
+
+struct clk *clk_get_fpi(void)
+{
+	return &cpu_clk_generic[1];
+}
+EXPORT_SYMBOL_GPL(clk_get_fpi);
+
+struct clk *clk_get_io(void)
+{
+	return &cpu_clk_generic[2];
+}
+EXPORT_SYMBOL_GPL(clk_get_io);
+
+struct clk *clk_get_ppe(void)
+{
+	return &cpu_clk_generic[3];
+}
+EXPORT_SYMBOL_GPL(clk_get_ppe);
+
+static inline int clk_good(struct clk *clk)
+{
+	return clk && !IS_ERR(clk);
+}
+
+unsigned long clk_get_rate(struct clk *clk)
+{
+	if (unlikely(!clk_good(clk)))
+		return 0;
+
+	if (clk->rate != 0)
+		return clk->rate;
+
+	if (clk->get_rate != NULL)
+		return clk->get_rate();
+
+	return 0;
+}
+EXPORT_SYMBOL(clk_get_rate);
+
+int clk_set_rate(struct clk *clk, unsigned long rate)
+{
+	if (unlikely(!clk_good(clk)))
+		return 0;
+	if (clk->rates && *clk->rates) {
+		unsigned long *r = clk->rates;
+
+		while (*r && (*r != rate))
+			r++;
+		if (!*r) {
+			pr_err("clk %s.%s: trying to set invalid rate %ld\n",
+				clk->cl.dev_id, clk->cl.con_id, rate);
+			return -1;
+		}
+	}
+	clk->rate = rate;
+	return 0;
+}
+EXPORT_SYMBOL(clk_set_rate);
+
+long clk_round_rate(struct clk *clk, unsigned long rate)
+{
+	if (unlikely(!clk_good(clk)))
+		return 0;
+	if (clk->rates && *clk->rates) {
+		unsigned long *r = clk->rates;
+
+		while (*r && (*r != rate))
+			r++;
+		if (!*r) {
+			return clk->rate;
+		}
+	}
+	return rate;
+}
+EXPORT_SYMBOL(clk_round_rate);
+
+int clk_enable(struct clk *clk)
+{
+	if (unlikely(!clk_good(clk)))
+		return -1;
+
+	if (clk->enable)
+		return clk->enable(clk);
+
+	return -1;
+}
+EXPORT_SYMBOL(clk_enable);
+
+void clk_disable(struct clk *clk)
+{
+	if (unlikely(!clk_good(clk)))
+		return;
+
+	if (clk->disable)
+		clk->disable(clk);
+}
+EXPORT_SYMBOL(clk_disable);
+
+int clk_activate(struct clk *clk)
+{
+	if (unlikely(!clk_good(clk)))
+		return -1;
+
+	if (clk->activate)
+		return clk->activate(clk);
+
+	return -1;
+}
+EXPORT_SYMBOL(clk_activate);
+
+void clk_deactivate(struct clk *clk)
+{
+	if (unlikely(!clk_good(clk)))
+		return;
+
+	if (clk->deactivate)
+		clk->deactivate(clk);
+}
+EXPORT_SYMBOL(clk_deactivate);
+
+struct clk *clk_get_parent(struct clk *clk)
+{
+	return NULL;
+}
+EXPORT_SYMBOL(clk_get_parent);
+
+int clk_set_parent(struct clk *clk, struct clk *parent)
+{
+	return 0;
+}
+EXPORT_SYMBOL(clk_set_parent);
+
+static inline u32 get_counter_resolution(void)
+{
+	u32 res;
+
+	__asm__ __volatile__(
+		".set	push\n"
+		".set	mips32r2\n"
+		"rdhwr	%0, $3\n"
+		".set pop\n"
+		: "=&r" (res)
+		: /* no input */
+		: "memory");
+
+	return res;
+}
+
+void __init plat_time_init(void)
+{
+	struct clk *clk;
+
+	ltq_soc_init();
+
+	clk = clk_get_cpu();
+	mips_hpt_frequency = clk_get_rate(clk) / get_counter_resolution();
+	write_c0_compare(read_c0_count());
+	pr_info("CPU Clock: %ldMHz\n", clk_get_rate(clk) / 1000000);
+	clk_put(clk);
+}
diff --git a/arch/mips/lantiq/clk.h b/arch/mips/lantiq/clk.h
new file mode 100644
index 000000000..f135e3035
--- /dev/null
+++ b/arch/mips/lantiq/clk.h
@@ -0,0 +1,94 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *
+ * Copyright (C) 2010 John Crispin <john@phrozen.org>
+ */
+
+#ifndef _LTQ_CLK_H__
+#define _LTQ_CLK_H__
+
+#include <linux/clkdev.h>
+
+/* clock speeds */
+#define CLOCK_33M	33333333
+#define CLOCK_60M	60000000
+#define CLOCK_62_5M	62500000
+#define CLOCK_83M	83333333
+#define CLOCK_83_5M	83500000
+#define CLOCK_98_304M	98304000
+#define CLOCK_100M	100000000
+#define CLOCK_111M	111111111
+#define CLOCK_125M	125000000
+#define CLOCK_133M	133333333
+#define CLOCK_150M	150000000
+#define CLOCK_166M	166666666
+#define CLOCK_167M	166666667
+#define CLOCK_196_608M	196608000
+#define CLOCK_200M	200000000
+#define CLOCK_222M	222000000
+#define CLOCK_240M	240000000
+#define CLOCK_250M	250000000
+#define CLOCK_266M	266666666
+#define CLOCK_288M	288888888
+#define CLOCK_300M	300000000
+#define CLOCK_333M	333333333
+#define CLOCK_360M	360000000
+#define CLOCK_393M	393215332
+#define CLOCK_400M	400000000
+#define CLOCK_432M	432000000
+#define CLOCK_450M	450000000
+#define CLOCK_500M	500000000
+#define CLOCK_600M	600000000
+#define CLOCK_666M	666666666
+#define CLOCK_720M	720000000
+
+/* clock out speeds */
+#define CLOCK_32_768K	32768
+#define CLOCK_1_536M	1536000
+#define CLOCK_2_5M	2500000
+#define CLOCK_12M	12000000
+#define CLOCK_24M	24000000
+#define CLOCK_25M	25000000
+#define CLOCK_30M	30000000
+#define CLOCK_40M	40000000
+#define CLOCK_48M	48000000
+#define CLOCK_50M	50000000
+#define CLOCK_60M	60000000
+
+struct clk {
+	struct clk_lookup cl;
+	unsigned long rate;
+	unsigned long *rates;
+	unsigned int module;
+	unsigned int bits;
+	unsigned long (*get_rate) (void);
+	int (*enable) (struct clk *clk);
+	void (*disable) (struct clk *clk);
+	int (*activate) (struct clk *clk);
+	void (*deactivate) (struct clk *clk);
+	void (*reboot) (struct clk *clk);
+};
+
+extern void clkdev_add_static(unsigned long cpu, unsigned long fpi,
+				unsigned long io, unsigned long ppe);
+
+extern unsigned long ltq_danube_cpu_hz(void);
+extern unsigned long ltq_danube_fpi_hz(void);
+extern unsigned long ltq_danube_pp32_hz(void);
+
+extern unsigned long ltq_ar9_cpu_hz(void);
+extern unsigned long ltq_ar9_fpi_hz(void);
+
+extern unsigned long ltq_vr9_cpu_hz(void);
+extern unsigned long ltq_vr9_fpi_hz(void);
+extern unsigned long ltq_vr9_pp32_hz(void);
+
+extern unsigned long ltq_ar10_cpu_hz(void);
+extern unsigned long ltq_ar10_fpi_hz(void);
+extern unsigned long ltq_ar10_pp32_hz(void);
+
+extern unsigned long ltq_grx390_cpu_hz(void);
+extern unsigned long ltq_grx390_fpi_hz(void);
+extern unsigned long ltq_grx390_pp32_hz(void);
+
+#endif
diff --git a/arch/mips/lantiq/early_printk.c b/arch/mips/lantiq/early_printk.c
new file mode 100644
index 000000000..4e4a28be1
--- /dev/null
+++ b/arch/mips/lantiq/early_printk.c
@@ -0,0 +1,31 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ *  Copyright (C) 2010 John Crispin <john@phrozen.org>
+ */
+
+#include <linux/cpu.h>
+#include <lantiq_soc.h>
+#include <asm/setup.h>
+
+#define ASC_BUF		1024
+#define LTQ_ASC_FSTAT	((u32 *)(LTQ_EARLY_ASC + 0x0048))
+#ifdef __BIG_ENDIAN
+#define LTQ_ASC_TBUF	((u32 *)(LTQ_EARLY_ASC + 0x0020 + 3))
+#else
+#define LTQ_ASC_TBUF	((u32 *)(LTQ_EARLY_ASC + 0x0020))
+#endif
+#define TXMASK		0x3F00
+#define TXOFFSET	8
+
+void prom_putchar(char c)
+{
+	unsigned long flags;
+
+	local_irq_save(flags);
+	do { } while ((ltq_r32(LTQ_ASC_FSTAT) & TXMASK) >> TXOFFSET);
+	if (c == '\n')
+		ltq_w8('\r', LTQ_ASC_TBUF);
+	ltq_w8(c, LTQ_ASC_TBUF);
+	local_irq_restore(flags);
+}
diff --git a/arch/mips/lantiq/falcon/Makefile b/arch/mips/lantiq/falcon/Makefile
new file mode 100644
index 000000000..98da1e031
--- /dev/null
+++ b/arch/mips/lantiq/falcon/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0-only
+obj-y := prom.o reset.o sysctrl.o
diff --git a/arch/mips/lantiq/falcon/prom.c b/arch/mips/lantiq/falcon/prom.c
new file mode 100644
index 000000000..7b98def10
--- /dev/null
+++ b/arch/mips/lantiq/falcon/prom.c
@@ -0,0 +1,90 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ * Copyright (C) 2012 Thomas Langer <thomas.langer@lantiq.com>
+ * Copyright (C) 2012 John Crispin <john@phrozen.org>
+ */
+
+#include <linux/kernel.h>
+#include <asm/cacheflush.h>
+#include <asm/traps.h>
+#include <asm/io.h>
+
+#include <lantiq_soc.h>
+
+#include "../prom.h"
+
+#define SOC_FALCON	"Falcon"
+#define SOC_FALCON_D	"Falcon-D"
+#define SOC_FALCON_V	"Falcon-V"
+#define SOC_FALCON_M	"Falcon-M"
+
+#define COMP_FALCON	"lantiq,falcon"
+
+#define PART_SHIFT	12
+#define PART_MASK	0x0FFFF000
+#define REV_SHIFT	28
+#define REV_MASK	0xF0000000
+#define SREV_SHIFT	22
+#define SREV_MASK	0x03C00000
+#define TYPE_SHIFT	26
+#define TYPE_MASK	0x3C000000
+
+/* reset, nmi and ejtag exception vectors */
+#define BOOT_REG_BASE	(KSEG1 | 0x1F200000)
+#define BOOT_RVEC	(BOOT_REG_BASE | 0x00)
+#define BOOT_NVEC	(BOOT_REG_BASE | 0x04)
+#define BOOT_EVEC	(BOOT_REG_BASE | 0x08)
+
+void __init ltq_soc_nmi_setup(void)
+{
+	extern void (*nmi_handler)(void);
+
+	ltq_w32((unsigned long)&nmi_handler, (void *)BOOT_NVEC);
+}
+
+void __init ltq_soc_ejtag_setup(void)
+{
+	extern void (*ejtag_debug_handler)(void);
+
+	ltq_w32((unsigned long)&ejtag_debug_handler, (void *)BOOT_EVEC);
+}
+
+void __init ltq_soc_detect(struct ltq_soc_info *i)
+{
+	u32 type;
+	i->partnum = (ltq_r32(FALCON_CHIPID) & PART_MASK) >> PART_SHIFT;
+	i->rev = (ltq_r32(FALCON_CHIPID) & REV_MASK) >> REV_SHIFT;
+	i->srev = ((ltq_r32(FALCON_CHIPCONF) & SREV_MASK) >> SREV_SHIFT);
+	i->compatible = COMP_FALCON;
+	i->type = SOC_TYPE_FALCON;
+	sprintf(i->rev_type, "%c%d%d", (i->srev & 0x4) ? ('B') : ('A'),
+		i->rev & 0x7, (i->srev & 0x3) + 1);
+
+	switch (i->partnum) {
+	case SOC_ID_FALCON:
+		type = (ltq_r32(FALCON_CHIPTYPE) & TYPE_MASK) >> TYPE_SHIFT;
+		switch (type) {
+		case 0:
+			i->name = SOC_FALCON_D;
+			break;
+		case 1:
+			i->name = SOC_FALCON_V;
+			break;
+		case 2:
+			i->name = SOC_FALCON_M;
+			break;
+		default:
+			i->name = SOC_FALCON;
+			break;
+		}
+		break;
+
+	default:
+		unreachable();
+		break;
+	}
+
+	board_nmi_handler_setup = ltq_soc_nmi_setup;
+	board_ejtag_handler_setup = ltq_soc_ejtag_setup;
+}
diff --git a/arch/mips/lantiq/falcon/reset.c b/arch/mips/lantiq/falcon/reset.c
new file mode 100644
index 000000000..261996c23
--- /dev/null
+++ b/arch/mips/lantiq/falcon/reset.c
@@ -0,0 +1,75 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ * Copyright (C) 2012 Thomas Langer <thomas.langer@lantiq.com>
+ * Copyright (C) 2012 John Crispin <john@phrozen.org>
+ */
+
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/pm.h>
+#include <asm/reboot.h>
+#include <linux/export.h>
+
+#include <lantiq_soc.h>
+
+/*
+ * Dummy implementation.  Used to allow platform code to find out what
+ * source was booted from
+ */
+unsigned char ltq_boot_select(void)
+{
+	return BS_SPI;
+}
+
+#define BOOT_REG_BASE	(KSEG1 | 0x1F200000)
+#define BOOT_PW1_REG	(BOOT_REG_BASE | 0x20)
+#define BOOT_PW2_REG	(BOOT_REG_BASE | 0x24)
+#define BOOT_PW1	0x4C545100
+#define BOOT_PW2	0x0051544C
+
+#define WDT_REG_BASE	(KSEG1 | 0x1F8803F0)
+#define WDT_PW1		0x00BE0000
+#define WDT_PW2		0x00DC0000
+
+static void machine_restart(char *command)
+{
+	local_irq_disable();
+
+	/* reboot magic */
+	ltq_w32(BOOT_PW1, (void *)BOOT_PW1_REG); /* 'LTQ\0' */
+	ltq_w32(BOOT_PW2, (void *)BOOT_PW2_REG); /* '\0QTL' */
+	ltq_w32(0, (void *)BOOT_REG_BASE); /* reset Bootreg RVEC */
+
+	/* watchdog magic */
+	ltq_w32(WDT_PW1, (void *)WDT_REG_BASE);
+	ltq_w32(WDT_PW2 |
+		(0x3 << 26) | /* PWL */
+		(0x2 << 24) | /* CLKDIV */
+		(0x1 << 31) | /* enable */
+		(1), /* reload */
+		(void *)WDT_REG_BASE);
+	unreachable();
+}
+
+static void machine_halt(void)
+{
+	local_irq_disable();
+	unreachable();
+}
+
+static void machine_power_off(void)
+{
+	local_irq_disable();
+	unreachable();
+}
+
+static int __init mips_reboot_setup(void)
+{
+	_machine_restart = machine_restart;
+	_machine_halt = machine_halt;
+	pm_power_off = machine_power_off;
+	return 0;
+}
+
+arch_initcall(mips_reboot_setup);
diff --git a/arch/mips/lantiq/falcon/sysctrl.c b/arch/mips/lantiq/falcon/sysctrl.c
new file mode 100644
index 000000000..1187729d8
--- /dev/null
+++ b/arch/mips/lantiq/falcon/sysctrl.c
@@ -0,0 +1,271 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ * Copyright (C) 2011 Thomas Langer <thomas.langer@lantiq.com>
+ * Copyright (C) 2011 John Crispin <john@phrozen.org>
+ */
+
+#include <linux/ioport.h>
+#include <linux/export.h>
+#include <linux/clkdev.h>
+#include <linux/of_address.h>
+#include <asm/delay.h>
+
+#include <lantiq_soc.h>
+
+#include "../clk.h"
+
+/* infrastructure control register */
+#define SYS1_INFRAC		0x00bc
+/* Configuration fuses for drivers and pll */
+#define STATUS_CONFIG		0x0040
+
+/* GPE frequency selection */
+#define GPPC_OFFSET		24
+#define GPEFREQ_MASK		0x0000C00
+#define GPEFREQ_OFFSET		10
+/* Clock status register */
+#define SYSCTL_CLKS		0x0000
+/* Clock enable register */
+#define SYSCTL_CLKEN		0x0004
+/* Clock clear register */
+#define SYSCTL_CLKCLR		0x0008
+/* Activation Status Register */
+#define SYSCTL_ACTS		0x0020
+/* Activation Register */
+#define SYSCTL_ACT		0x0024
+/* Deactivation Register */
+#define SYSCTL_DEACT		0x0028
+/* reboot Register */
+#define SYSCTL_RBT		0x002c
+/* CPU0 Clock Control Register */
+#define SYS1_CPU0CC		0x0040
+/* HRST_OUT_N Control Register */
+#define SYS1_HRSTOUTC		0x00c0
+/* clock divider bit */
+#define CPU0CC_CPUDIV		0x0001
+
+/* Activation Status Register */
+#define ACTS_ASC0_ACT	0x00001000
+#define ACTS_SSC0	0x00002000
+#define ACTS_ASC1_ACT	0x00000800
+#define ACTS_I2C_ACT	0x00004000
+#define ACTS_P0		0x00010000
+#define ACTS_P1		0x00010000
+#define ACTS_P2		0x00020000
+#define ACTS_P3		0x00020000
+#define ACTS_P4		0x00040000
+#define ACTS_PADCTRL0	0x00100000
+#define ACTS_PADCTRL1	0x00100000
+#define ACTS_PADCTRL2	0x00200000
+#define ACTS_PADCTRL3	0x00200000
+#define ACTS_PADCTRL4	0x00400000
+
+#define sysctl_w32(m, x, y)	ltq_w32((x), sysctl_membase[m] + (y))
+#define sysctl_r32(m, x)	ltq_r32(sysctl_membase[m] + (x))
+#define sysctl_w32_mask(m, clear, set, reg)	\
+		sysctl_w32(m, (sysctl_r32(m, reg) & ~(clear)) | (set), reg)
+
+#define status_w32(x, y)	ltq_w32((x), status_membase + (y))
+#define status_r32(x)		ltq_r32(status_membase + (x))
+
+static void __iomem *sysctl_membase[3], *status_membase;
+void __iomem *ltq_sys1_membase, *ltq_ebu_membase;
+
+void falcon_trigger_hrst(int level)
+{
+	sysctl_w32(SYSCTL_SYS1, level & 1, SYS1_HRSTOUTC);
+}
+
+static inline void sysctl_wait(struct clk *clk,
+		unsigned int test, unsigned int reg)
+{
+	int err = 1000000;
+
+	do {} while (--err && ((sysctl_r32(clk->module, reg)
+					& clk->bits) != test));
+	if (!err)
+		pr_err("module de/activation failed %d %08X %08X %08X\n",
+			clk->module, clk->bits, test,
+			sysctl_r32(clk->module, reg) & clk->bits);
+}
+
+static int sysctl_activate(struct clk *clk)
+{
+	sysctl_w32(clk->module, clk->bits, SYSCTL_CLKEN);
+	sysctl_w32(clk->module, clk->bits, SYSCTL_ACT);
+	sysctl_wait(clk, clk->bits, SYSCTL_ACTS);
+	return 0;
+}
+
+static void sysctl_deactivate(struct clk *clk)
+{
+	sysctl_w32(clk->module, clk->bits, SYSCTL_CLKCLR);
+	sysctl_w32(clk->module, clk->bits, SYSCTL_DEACT);
+	sysctl_wait(clk, 0, SYSCTL_ACTS);
+}
+
+static int sysctl_clken(struct clk *clk)
+{
+	sysctl_w32(clk->module, clk->bits, SYSCTL_CLKEN);
+	sysctl_w32(clk->module, clk->bits, SYSCTL_ACT);
+	sysctl_wait(clk, clk->bits, SYSCTL_CLKS);
+	return 0;
+}
+
+static void sysctl_clkdis(struct clk *clk)
+{
+	sysctl_w32(clk->module, clk->bits, SYSCTL_CLKCLR);
+	sysctl_wait(clk, 0, SYSCTL_CLKS);
+}
+
+static void sysctl_reboot(struct clk *clk)
+{
+	unsigned int act;
+	unsigned int bits;
+
+	act = sysctl_r32(clk->module, SYSCTL_ACT);
+	bits = ~act & clk->bits;
+	if (bits != 0) {
+		sysctl_w32(clk->module, bits, SYSCTL_CLKEN);
+		sysctl_w32(clk->module, bits, SYSCTL_ACT);
+		sysctl_wait(clk, bits, SYSCTL_ACTS);
+	}
+	sysctl_w32(clk->module, act & clk->bits, SYSCTL_RBT);
+	sysctl_wait(clk, clk->bits, SYSCTL_ACTS);
+}
+
+/* enable the ONU core */
+static void falcon_gpe_enable(void)
+{
+	unsigned int freq;
+	unsigned int status;
+
+	/* if the clock is already enabled */
+	status = sysctl_r32(SYSCTL_SYS1, SYS1_INFRAC);
+	if (status & (1 << (GPPC_OFFSET + 1)))
+		return;
+
+	freq = (status_r32(STATUS_CONFIG) &
+		GPEFREQ_MASK) >>
+		GPEFREQ_OFFSET;
+	if (freq == 0)
+		freq = 1; /* use 625MHz on unfused chip */
+
+	/* apply new frequency */
+	sysctl_w32_mask(SYSCTL_SYS1, 7 << (GPPC_OFFSET + 1),
+		freq << (GPPC_OFFSET + 2) , SYS1_INFRAC);
+	udelay(1);
+
+	/* enable new frequency */
+	sysctl_w32_mask(SYSCTL_SYS1, 0, 1 << (GPPC_OFFSET + 1), SYS1_INFRAC);
+	udelay(1);
+}
+
+static inline void clkdev_add_sys(const char *dev, unsigned int module,
+					unsigned int bits)
+{
+	struct clk *clk = kzalloc(sizeof(struct clk), GFP_KERNEL);
+
+	if (!clk)
+		return;
+	clk->cl.dev_id = dev;
+	clk->cl.con_id = NULL;
+	clk->cl.clk = clk;
+	clk->module = module;
+	clk->bits = bits;
+	clk->activate = sysctl_activate;
+	clk->deactivate = sysctl_deactivate;
+	clk->enable = sysctl_clken;
+	clk->disable = sysctl_clkdis;
+	clk->reboot = sysctl_reboot;
+	clkdev_add(&clk->cl);
+}
+
+void __init ltq_soc_init(void)
+{
+	struct device_node *np_status =
+		of_find_compatible_node(NULL, NULL, "lantiq,status-falcon");
+	struct device_node *np_ebu =
+		of_find_compatible_node(NULL, NULL, "lantiq,ebu-falcon");
+	struct device_node *np_sys1 =
+		of_find_compatible_node(NULL, NULL, "lantiq,sys1-falcon");
+	struct device_node *np_syseth =
+		of_find_compatible_node(NULL, NULL, "lantiq,syseth-falcon");
+	struct device_node *np_sysgpe =
+		of_find_compatible_node(NULL, NULL, "lantiq,sysgpe-falcon");
+	struct resource res_status, res_ebu, res_sys[3];
+	int i;
+
+	/* check if all the core register ranges are available */
+	if (!np_status || !np_ebu || !np_sys1 || !np_syseth || !np_sysgpe)
+		panic("Failed to load core nodes from devicetree");
+
+	if (of_address_to_resource(np_status, 0, &res_status) ||
+			of_address_to_resource(np_ebu, 0, &res_ebu) ||
+			of_address_to_resource(np_sys1, 0, &res_sys[0]) ||
+			of_address_to_resource(np_syseth, 0, &res_sys[1]) ||
+			of_address_to_resource(np_sysgpe, 0, &res_sys[2]))
+		panic("Failed to get core resources");
+
+	of_node_put(np_status);
+	of_node_put(np_ebu);
+	of_node_put(np_sys1);
+	of_node_put(np_syseth);
+	of_node_put(np_sysgpe);
+
+	if ((request_mem_region(res_status.start, resource_size(&res_status),
+				res_status.name) < 0) ||
+		(request_mem_region(res_ebu.start, resource_size(&res_ebu),
+				res_ebu.name) < 0) ||
+		(request_mem_region(res_sys[0].start,
+				resource_size(&res_sys[0]),
+				res_sys[0].name) < 0) ||
+		(request_mem_region(res_sys[1].start,
+				resource_size(&res_sys[1]),
+				res_sys[1].name) < 0) ||
+		(request_mem_region(res_sys[2].start,
+				resource_size(&res_sys[2]),
+				res_sys[2].name) < 0))
+		pr_err("Failed to request core resources");
+
+	status_membase = ioremap(res_status.start,
+					resource_size(&res_status));
+	ltq_ebu_membase = ioremap(res_ebu.start,
+					resource_size(&res_ebu));
+
+	if (!status_membase || !ltq_ebu_membase)
+		panic("Failed to remap core resources");
+
+	for (i = 0; i < 3; i++) {
+		sysctl_membase[i] = ioremap(res_sys[i].start,
+						resource_size(&res_sys[i]));
+		if (!sysctl_membase[i])
+			panic("Failed to remap sysctrl resources");
+	}
+	ltq_sys1_membase = sysctl_membase[0];
+
+	falcon_gpe_enable();
+
+	/* get our 3 static rates for cpu, fpi and io clocks */
+	if (ltq_sys1_r32(SYS1_CPU0CC) & CPU0CC_CPUDIV)
+		clkdev_add_static(CLOCK_200M, CLOCK_100M, CLOCK_200M, 0);
+	else
+		clkdev_add_static(CLOCK_400M, CLOCK_100M, CLOCK_200M, 0);
+
+	/* add our clock domains */
+	clkdev_add_sys("1d810000.gpio", SYSCTL_SYSETH, ACTS_P0);
+	clkdev_add_sys("1d810100.gpio", SYSCTL_SYSETH, ACTS_P2);
+	clkdev_add_sys("1e800100.gpio", SYSCTL_SYS1, ACTS_P1);
+	clkdev_add_sys("1e800200.gpio", SYSCTL_SYS1, ACTS_P3);
+	clkdev_add_sys("1e800300.gpio", SYSCTL_SYS1, ACTS_P4);
+	clkdev_add_sys("1db01000.pad", SYSCTL_SYSETH, ACTS_PADCTRL0);
+	clkdev_add_sys("1db02000.pad", SYSCTL_SYSETH, ACTS_PADCTRL2);
+	clkdev_add_sys("1e800400.pad", SYSCTL_SYS1, ACTS_PADCTRL1);
+	clkdev_add_sys("1e800500.pad", SYSCTL_SYS1, ACTS_PADCTRL3);
+	clkdev_add_sys("1e800600.pad", SYSCTL_SYS1, ACTS_PADCTRL4);
+	clkdev_add_sys("1e100b00.serial", SYSCTL_SYS1, ACTS_ASC1_ACT);
+	clkdev_add_sys("1e100c00.serial", SYSCTL_SYS1, ACTS_ASC0_ACT);
+	clkdev_add_sys("1e100d00.spi", SYSCTL_SYS1, ACTS_SSC0);
+	clkdev_add_sys("1e200000.i2c", SYSCTL_SYS1, ACTS_I2C_ACT);
+}
diff --git a/arch/mips/lantiq/irq.c b/arch/mips/lantiq/irq.c
new file mode 100644
index 000000000..20622bf0a
--- /dev/null
+++ b/arch/mips/lantiq/irq.c
@@ -0,0 +1,432 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ * Copyright (C) 2010 John Crispin <john@phrozen.org>
+ * Copyright (C) 2010 Thomas Langer <thomas.langer@lantiq.com>
+ */
+
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/sched.h>
+#include <linux/irqchip.h>
+#include <linux/irqdomain.h>
+#include <linux/of_platform.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+
+#include <asm/bootinfo.h>
+#include <asm/irq_cpu.h>
+
+#include <lantiq_soc.h>
+#include <irq.h>
+
+/* register definitions - internal irqs */
+#define LTQ_ICU_ISR		0x0000
+#define LTQ_ICU_IER		0x0008
+#define LTQ_ICU_IOSR		0x0010
+#define LTQ_ICU_IRSR		0x0018
+#define LTQ_ICU_IMR		0x0020
+
+#define LTQ_ICU_IM_SIZE		0x28
+
+/* register definitions - external irqs */
+#define LTQ_EIU_EXIN_C		0x0000
+#define LTQ_EIU_EXIN_INIC	0x0004
+#define LTQ_EIU_EXIN_INC	0x0008
+#define LTQ_EIU_EXIN_INEN	0x000C
+
+/* number of external interrupts */
+#define MAX_EIU			6
+
+/* the performance counter */
+#define LTQ_PERF_IRQ		(INT_NUM_IM4_IRL0 + 31)
+
+/*
+ * irqs generated by devices attached to the EBU need to be acked in
+ * a special manner
+ */
+#define LTQ_ICU_EBU_IRQ		22
+
+#define ltq_icu_w32(vpe, m, x, y)	\
+	ltq_w32((x), ltq_icu_membase[vpe] + m*LTQ_ICU_IM_SIZE + (y))
+
+#define ltq_icu_r32(vpe, m, x)		\
+	ltq_r32(ltq_icu_membase[vpe] + m*LTQ_ICU_IM_SIZE + (x))
+
+#define ltq_eiu_w32(x, y)	ltq_w32((x), ltq_eiu_membase + (y))
+#define ltq_eiu_r32(x)		ltq_r32(ltq_eiu_membase + (x))
+
+/* we have a cascade of 8 irqs */
+#define MIPS_CPU_IRQ_CASCADE		8
+
+static int exin_avail;
+static u32 ltq_eiu_irq[MAX_EIU];
+static void __iomem *ltq_icu_membase[NR_CPUS];
+static void __iomem *ltq_eiu_membase;
+static struct irq_domain *ltq_domain;
+static DEFINE_SPINLOCK(ltq_eiu_lock);
+static DEFINE_RAW_SPINLOCK(ltq_icu_lock);
+static int ltq_perfcount_irq;
+
+int ltq_eiu_get_irq(int exin)
+{
+	if (exin < exin_avail)
+		return ltq_eiu_irq[exin];
+	return -1;
+}
+
+void ltq_disable_irq(struct irq_data *d)
+{
+	unsigned long offset = d->hwirq - MIPS_CPU_IRQ_CASCADE;
+	unsigned long im = offset / INT_NUM_IM_OFFSET;
+	unsigned long flags;
+	int vpe;
+
+	offset %= INT_NUM_IM_OFFSET;
+
+	raw_spin_lock_irqsave(&ltq_icu_lock, flags);
+	for_each_present_cpu(vpe) {
+		ltq_icu_w32(vpe, im,
+			    ltq_icu_r32(vpe, im, LTQ_ICU_IER) & ~BIT(offset),
+			    LTQ_ICU_IER);
+	}
+	raw_spin_unlock_irqrestore(&ltq_icu_lock, flags);
+}
+
+void ltq_mask_and_ack_irq(struct irq_data *d)
+{
+	unsigned long offset = d->hwirq - MIPS_CPU_IRQ_CASCADE;
+	unsigned long im = offset / INT_NUM_IM_OFFSET;
+	unsigned long flags;
+	int vpe;
+
+	offset %= INT_NUM_IM_OFFSET;
+
+	raw_spin_lock_irqsave(&ltq_icu_lock, flags);
+	for_each_present_cpu(vpe) {
+		ltq_icu_w32(vpe, im,
+			    ltq_icu_r32(vpe, im, LTQ_ICU_IER) & ~BIT(offset),
+			    LTQ_ICU_IER);
+		ltq_icu_w32(vpe, im, BIT(offset), LTQ_ICU_ISR);
+	}
+	raw_spin_unlock_irqrestore(&ltq_icu_lock, flags);
+}
+
+static void ltq_ack_irq(struct irq_data *d)
+{
+	unsigned long offset = d->hwirq - MIPS_CPU_IRQ_CASCADE;
+	unsigned long im = offset / INT_NUM_IM_OFFSET;
+	unsigned long flags;
+	int vpe;
+
+	offset %= INT_NUM_IM_OFFSET;
+
+	raw_spin_lock_irqsave(&ltq_icu_lock, flags);
+	for_each_present_cpu(vpe) {
+		ltq_icu_w32(vpe, im, BIT(offset), LTQ_ICU_ISR);
+	}
+	raw_spin_unlock_irqrestore(&ltq_icu_lock, flags);
+}
+
+void ltq_enable_irq(struct irq_data *d)
+{
+	unsigned long offset = d->hwirq - MIPS_CPU_IRQ_CASCADE;
+	unsigned long im = offset / INT_NUM_IM_OFFSET;
+	unsigned long flags;
+	int vpe;
+
+	offset %= INT_NUM_IM_OFFSET;
+
+	vpe = cpumask_first(irq_data_get_effective_affinity_mask(d));
+
+	/* This shouldn't be even possible, maybe during CPU hotplug spam */
+	if (unlikely(vpe >= nr_cpu_ids))
+		vpe = smp_processor_id();
+
+	raw_spin_lock_irqsave(&ltq_icu_lock, flags);
+
+	ltq_icu_w32(vpe, im, ltq_icu_r32(vpe, im, LTQ_ICU_IER) | BIT(offset),
+		    LTQ_ICU_IER);
+
+	raw_spin_unlock_irqrestore(&ltq_icu_lock, flags);
+}
+
+static int ltq_eiu_settype(struct irq_data *d, unsigned int type)
+{
+	int i;
+	unsigned long flags;
+
+	for (i = 0; i < exin_avail; i++) {
+		if (d->hwirq == ltq_eiu_irq[i]) {
+			int val = 0;
+			int edge = 0;
+
+			switch (type) {
+			case IRQF_TRIGGER_NONE:
+				break;
+			case IRQF_TRIGGER_RISING:
+				val = 1;
+				edge = 1;
+				break;
+			case IRQF_TRIGGER_FALLING:
+				val = 2;
+				edge = 1;
+				break;
+			case IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING:
+				val = 3;
+				edge = 1;
+				break;
+			case IRQF_TRIGGER_HIGH:
+				val = 5;
+				break;
+			case IRQF_TRIGGER_LOW:
+				val = 6;
+				break;
+			default:
+				pr_err("invalid type %d for irq %ld\n",
+					type, d->hwirq);
+				return -EINVAL;
+			}
+
+			if (edge)
+				irq_set_handler(d->hwirq, handle_edge_irq);
+
+			spin_lock_irqsave(&ltq_eiu_lock, flags);
+			ltq_eiu_w32((ltq_eiu_r32(LTQ_EIU_EXIN_C) &
+				    (~(7 << (i * 4)))) | (val << (i * 4)),
+				    LTQ_EIU_EXIN_C);
+			spin_unlock_irqrestore(&ltq_eiu_lock, flags);
+		}
+	}
+
+	return 0;
+}
+
+static unsigned int ltq_startup_eiu_irq(struct irq_data *d)
+{
+	int i;
+
+	ltq_enable_irq(d);
+	for (i = 0; i < exin_avail; i++) {
+		if (d->hwirq == ltq_eiu_irq[i]) {
+			/* by default we are low level triggered */
+			ltq_eiu_settype(d, IRQF_TRIGGER_LOW);
+			/* clear all pending */
+			ltq_eiu_w32(ltq_eiu_r32(LTQ_EIU_EXIN_INC) & ~BIT(i),
+				LTQ_EIU_EXIN_INC);
+			/* enable */
+			ltq_eiu_w32(ltq_eiu_r32(LTQ_EIU_EXIN_INEN) | BIT(i),
+				LTQ_EIU_EXIN_INEN);
+			break;
+		}
+	}
+
+	return 0;
+}
+
+static void ltq_shutdown_eiu_irq(struct irq_data *d)
+{
+	int i;
+
+	ltq_disable_irq(d);
+	for (i = 0; i < exin_avail; i++) {
+		if (d->hwirq == ltq_eiu_irq[i]) {
+			/* disable */
+			ltq_eiu_w32(ltq_eiu_r32(LTQ_EIU_EXIN_INEN) & ~BIT(i),
+				LTQ_EIU_EXIN_INEN);
+			break;
+		}
+	}
+}
+
+#if defined(CONFIG_SMP)
+static int ltq_icu_irq_set_affinity(struct irq_data *d,
+				    const struct cpumask *cpumask, bool force)
+{
+	struct cpumask tmask;
+
+	if (!cpumask_and(&tmask, cpumask, cpu_online_mask))
+		return -EINVAL;
+
+	irq_data_update_effective_affinity(d, &tmask);
+
+	return IRQ_SET_MASK_OK;
+}
+#endif
+
+static struct irq_chip ltq_irq_type = {
+	.name = "icu",
+	.irq_enable = ltq_enable_irq,
+	.irq_disable = ltq_disable_irq,
+	.irq_unmask = ltq_enable_irq,
+	.irq_ack = ltq_ack_irq,
+	.irq_mask = ltq_disable_irq,
+	.irq_mask_ack = ltq_mask_and_ack_irq,
+#if defined(CONFIG_SMP)
+	.irq_set_affinity = ltq_icu_irq_set_affinity,
+#endif
+};
+
+static struct irq_chip ltq_eiu_type = {
+	.name = "eiu",
+	.irq_startup = ltq_startup_eiu_irq,
+	.irq_shutdown = ltq_shutdown_eiu_irq,
+	.irq_enable = ltq_enable_irq,
+	.irq_disable = ltq_disable_irq,
+	.irq_unmask = ltq_enable_irq,
+	.irq_ack = ltq_ack_irq,
+	.irq_mask = ltq_disable_irq,
+	.irq_mask_ack = ltq_mask_and_ack_irq,
+	.irq_set_type = ltq_eiu_settype,
+#if defined(CONFIG_SMP)
+	.irq_set_affinity = ltq_icu_irq_set_affinity,
+#endif
+};
+
+static void ltq_hw_irq_handler(struct irq_desc *desc)
+{
+	unsigned int module = irq_desc_get_irq(desc) - 2;
+	u32 irq;
+	irq_hw_number_t hwirq;
+	int vpe = smp_processor_id();
+
+	irq = ltq_icu_r32(vpe, module, LTQ_ICU_IOSR);
+	if (irq == 0)
+		return;
+
+	/*
+	 * silicon bug causes only the msb set to 1 to be valid. all
+	 * other bits might be bogus
+	 */
+	irq = __fls(irq);
+	hwirq = irq + MIPS_CPU_IRQ_CASCADE + (INT_NUM_IM_OFFSET * module);
+	generic_handle_domain_irq(ltq_domain, hwirq);
+
+	/* if this is a EBU irq, we need to ack it or get a deadlock */
+	if (irq == LTQ_ICU_EBU_IRQ && !module && LTQ_EBU_PCC_ISTAT != 0)
+		ltq_ebu_w32(ltq_ebu_r32(LTQ_EBU_PCC_ISTAT) | 0x10,
+			LTQ_EBU_PCC_ISTAT);
+}
+
+static int icu_map(struct irq_domain *d, unsigned int irq, irq_hw_number_t hw)
+{
+	struct irq_chip *chip = &ltq_irq_type;
+	struct irq_data *data;
+	int i;
+
+	if (hw < MIPS_CPU_IRQ_CASCADE)
+		return 0;
+
+	for (i = 0; i < exin_avail; i++)
+		if (hw == ltq_eiu_irq[i])
+			chip = &ltq_eiu_type;
+
+	data = irq_get_irq_data(irq);
+
+	irq_data_update_effective_affinity(data, cpumask_of(0));
+
+	irq_set_chip_and_handler(irq, chip, handle_level_irq);
+
+	return 0;
+}
+
+static const struct irq_domain_ops irq_domain_ops = {
+	.xlate = irq_domain_xlate_onetwocell,
+	.map = icu_map,
+};
+
+int __init icu_of_init(struct device_node *node, struct device_node *parent)
+{
+	struct device_node *eiu_node;
+	struct resource res;
+	int i, ret, vpe;
+
+	/* load register regions of available ICUs */
+	for_each_possible_cpu(vpe) {
+		if (of_address_to_resource(node, vpe, &res))
+			panic("Failed to get icu%i memory range", vpe);
+
+		if (!request_mem_region(res.start, resource_size(&res),
+					res.name))
+			pr_err("Failed to request icu%i memory\n", vpe);
+
+		ltq_icu_membase[vpe] = ioremap(res.start,
+					resource_size(&res));
+
+		if (!ltq_icu_membase[vpe])
+			panic("Failed to remap icu%i memory", vpe);
+	}
+
+	/* turn off all irqs by default */
+	for_each_possible_cpu(vpe) {
+		for (i = 0; i < MAX_IM; i++) {
+			/* make sure all irqs are turned off by default */
+			ltq_icu_w32(vpe, i, 0, LTQ_ICU_IER);
+
+			/* clear all possibly pending interrupts */
+			ltq_icu_w32(vpe, i, ~0, LTQ_ICU_ISR);
+			ltq_icu_w32(vpe, i, ~0, LTQ_ICU_IMR);
+
+			/* clear resend */
+			ltq_icu_w32(vpe, i, 0, LTQ_ICU_IRSR);
+		}
+	}
+
+	mips_cpu_irq_init();
+
+	for (i = 0; i < MAX_IM; i++)
+		irq_set_chained_handler(i + 2, ltq_hw_irq_handler);
+
+	ltq_domain = irq_domain_add_linear(node,
+		(MAX_IM * INT_NUM_IM_OFFSET) + MIPS_CPU_IRQ_CASCADE,
+		&irq_domain_ops, 0);
+
+	/* tell oprofile which irq to use */
+	ltq_perfcount_irq = irq_create_mapping(ltq_domain, LTQ_PERF_IRQ);
+
+	/* the external interrupts are optional and xway only */
+	eiu_node = of_find_compatible_node(NULL, NULL, "lantiq,eiu-xway");
+	if (eiu_node && !of_address_to_resource(eiu_node, 0, &res)) {
+		/* find out how many external irq sources we have */
+		exin_avail = of_property_count_u32_elems(eiu_node,
+							 "lantiq,eiu-irqs");
+
+		if (exin_avail > MAX_EIU)
+			exin_avail = MAX_EIU;
+
+		ret = of_property_read_u32_array(eiu_node, "lantiq,eiu-irqs",
+						ltq_eiu_irq, exin_avail);
+		if (ret)
+			panic("failed to load external irq resources");
+
+		if (!request_mem_region(res.start, resource_size(&res),
+							res.name))
+			pr_err("Failed to request eiu memory");
+
+		ltq_eiu_membase = ioremap(res.start,
+							resource_size(&res));
+		if (!ltq_eiu_membase)
+			panic("Failed to remap eiu memory");
+	}
+	of_node_put(eiu_node);
+
+	return 0;
+}
+
+int get_c0_perfcount_int(void)
+{
+	return ltq_perfcount_irq;
+}
+EXPORT_SYMBOL_GPL(get_c0_perfcount_int);
+
+unsigned int get_c0_compare_int(void)
+{
+	return CP0_LEGACY_COMPARE_IRQ;
+}
+
+IRQCHIP_DECLARE(lantiq_icu, "lantiq,icu", icu_of_init);
+
+void __init arch_init_irq(void)
+{
+	irqchip_init();
+}
diff --git a/arch/mips/lantiq/prom.c b/arch/mips/lantiq/prom.c
new file mode 100644
index 000000000..28da4e720
--- /dev/null
+++ b/arch/mips/lantiq/prom.c
@@ -0,0 +1,122 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ * Copyright (C) 2010 John Crispin <john@phrozen.org>
+ */
+
+#include <linux/export.h>
+#include <linux/clk.h>
+#include <linux/memblock.h>
+#include <linux/of_fdt.h>
+
+#include <asm/bootinfo.h>
+#include <asm/time.h>
+#include <asm/prom.h>
+
+#include <lantiq.h>
+
+#include "prom.h"
+#include "clk.h"
+
+/* access to the ebu needs to be locked between different drivers */
+DEFINE_SPINLOCK(ebu_lock);
+EXPORT_SYMBOL_GPL(ebu_lock);
+
+/*
+ * This is needed by the VPE loader code, just set it to 0 and assume
+ * that the firmware hardcodes this value to something useful.
+ */
+unsigned long physical_memsize = 0L;
+
+/*
+ * this struct is filled by the soc specific detection code and holds
+ * information about the specific soc type, revision and name
+ */
+static struct ltq_soc_info soc_info;
+
+/*
+ * These structs are used to override vsmp_init_secondary()
+ */
+#if defined(CONFIG_MIPS_MT_SMP)
+extern const struct plat_smp_ops vsmp_smp_ops;
+static struct plat_smp_ops lantiq_smp_ops;
+#endif
+
+const char *get_system_type(void)
+{
+	return soc_info.sys_type;
+}
+
+int ltq_soc_type(void)
+{
+	return soc_info.type;
+}
+
+static void __init prom_init_cmdline(void)
+{
+	int argc = fw_arg0;
+	char **argv = (char **) KSEG1ADDR(fw_arg1);
+	int i;
+
+	arcs_cmdline[0] = '\0';
+
+	for (i = 0; i < argc; i++) {
+		char *p = (char *) KSEG1ADDR(argv[i]);
+
+		if (CPHYSADDR(p) && *p) {
+			strlcat(arcs_cmdline, p, sizeof(arcs_cmdline));
+			strlcat(arcs_cmdline, " ", sizeof(arcs_cmdline));
+		}
+	}
+}
+
+void __init plat_mem_setup(void)
+{
+	void *dtb;
+
+	ioport_resource.start = IOPORT_RESOURCE_START;
+	ioport_resource.end = IOPORT_RESOURCE_END;
+	iomem_resource.start = IOMEM_RESOURCE_START;
+	iomem_resource.end = IOMEM_RESOURCE_END;
+
+	set_io_port_base((unsigned long) KSEG1);
+
+	dtb = get_fdt();
+	if (dtb == NULL)
+		panic("no dtb found");
+
+	/*
+	 * Load the devicetree. This causes the chosen node to be
+	 * parsed resulting in our memory appearing
+	 */
+	__dt_setup_arch(dtb);
+}
+
+#if defined(CONFIG_MIPS_MT_SMP)
+static void lantiq_init_secondary(void)
+{
+	/*
+	 * MIPS CPU startup function vsmp_init_secondary() will only
+	 * enable some of the interrupts for the second CPU/VPE.
+	 */
+	set_c0_status(ST0_IM);
+}
+#endif
+
+void __init prom_init(void)
+{
+	/* call the soc specific detetcion code and get it to fill soc_info */
+	ltq_soc_detect(&soc_info);
+	snprintf(soc_info.sys_type, LTQ_SYS_TYPE_LEN - 1, "%s rev %s",
+		soc_info.name, soc_info.rev_type);
+	soc_info.sys_type[LTQ_SYS_TYPE_LEN - 1] = '\0';
+	pr_info("SoC: %s\n", soc_info.sys_type);
+	prom_init_cmdline();
+
+#if defined(CONFIG_MIPS_MT_SMP)
+	lantiq_smp_ops = vsmp_smp_ops;
+	if (cpu_has_mipsmt)
+		lantiq_smp_ops.init_secondary = lantiq_init_secondary;
+	register_smp_ops(&lantiq_smp_ops);
+#endif
+}
diff --git a/arch/mips/lantiq/prom.h b/arch/mips/lantiq/prom.h
new file mode 100644
index 000000000..5cd29c6b3
--- /dev/null
+++ b/arch/mips/lantiq/prom.h
@@ -0,0 +1,27 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *
+ * Copyright (C) 2010 John Crispin <john@phrozen.org>
+ */
+
+#ifndef _LTQ_PROM_H__
+#define _LTQ_PROM_H__
+
+#define LTQ_SYS_TYPE_LEN	0x100
+#define LTQ_SYS_REV_LEN		0x10
+
+struct ltq_soc_info {
+	unsigned char *name;
+	unsigned int rev;
+	unsigned char rev_type[LTQ_SYS_REV_LEN];
+	unsigned int srev;
+	unsigned int partnum;
+	unsigned int type;
+	unsigned char sys_type[LTQ_SYS_TYPE_LEN];
+	unsigned char *compatible;
+};
+
+extern void ltq_soc_detect(struct ltq_soc_info *i);
+extern void ltq_soc_init(void);
+
+#endif
diff --git a/arch/mips/lantiq/xway/Makefile b/arch/mips/lantiq/xway/Makefile
new file mode 100644
index 000000000..c0f02dab7
--- /dev/null
+++ b/arch/mips/lantiq/xway/Makefile
@@ -0,0 +1,4 @@
+# SPDX-License-Identifier: GPL-2.0-only
+obj-y := prom.o sysctrl.o clk.o dma.o gptu.o dcdc.o
+
+obj-y += vmmc.o
diff --git a/arch/mips/lantiq/xway/clk.c b/arch/mips/lantiq/xway/clk.c
new file mode 100644
index 000000000..47ad21430
--- /dev/null
+++ b/arch/mips/lantiq/xway/clk.c
@@ -0,0 +1,351 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ *  Copyright (C) 2010 John Crispin <john@phrozen.org>
+ *  Copyright (C) 2013-2015 Lantiq Beteiligungs-GmbH & Co.KG
+ */
+
+#include <linux/io.h>
+#include <linux/export.h>
+#include <linux/clk.h>
+
+#include <asm/time.h>
+#include <asm/irq.h>
+#include <asm/div64.h>
+
+#include <lantiq_soc.h>
+
+#include "../clk.h"
+
+static unsigned int ram_clocks[] = {
+	CLOCK_167M, CLOCK_133M, CLOCK_111M, CLOCK_83M };
+#define DDR_HZ ram_clocks[ltq_cgu_r32(CGU_SYS) & 0x3]
+
+/* legacy xway clock */
+#define CGU_SYS			0x10
+
+/* vr9, ar10/grx390 clock */
+#define CGU_SYS_XRX		0x0c
+#define CGU_IF_CLK_AR10		0x24
+
+unsigned long ltq_danube_fpi_hz(void)
+{
+	unsigned long ddr_clock = DDR_HZ;
+
+	if (ltq_cgu_r32(CGU_SYS) & 0x40)
+		return ddr_clock >> 1;
+	return ddr_clock;
+}
+
+unsigned long ltq_danube_cpu_hz(void)
+{
+	switch (ltq_cgu_r32(CGU_SYS) & 0xc) {
+	case 0:
+		return CLOCK_333M;
+	case 4:
+		return DDR_HZ;
+	case 8:
+		return DDR_HZ << 1;
+	default:
+		return DDR_HZ >> 1;
+	}
+}
+
+unsigned long ltq_danube_pp32_hz(void)
+{
+	unsigned int clksys = (ltq_cgu_r32(CGU_SYS) >> 7) & 3;
+	unsigned long clk;
+
+	switch (clksys) {
+	case 1:
+		clk = CLOCK_240M;
+		break;
+	case 2:
+		clk = CLOCK_222M;
+		break;
+	case 3:
+		clk = CLOCK_133M;
+		break;
+	default:
+		clk = CLOCK_266M;
+		break;
+	}
+
+	return clk;
+}
+
+unsigned long ltq_ar9_sys_hz(void)
+{
+	if (((ltq_cgu_r32(CGU_SYS) >> 3) & 0x3) == 0x2)
+		return CLOCK_393M;
+	return CLOCK_333M;
+}
+
+unsigned long ltq_ar9_fpi_hz(void)
+{
+	unsigned long sys = ltq_ar9_sys_hz();
+
+	if (ltq_cgu_r32(CGU_SYS) & BIT(0))
+		return sys / 3;
+	else
+		return sys / 2;
+}
+
+unsigned long ltq_ar9_cpu_hz(void)
+{
+	if (ltq_cgu_r32(CGU_SYS) & BIT(2))
+		return ltq_ar9_fpi_hz();
+	else
+		return ltq_ar9_sys_hz();
+}
+
+unsigned long ltq_vr9_cpu_hz(void)
+{
+	unsigned int cpu_sel;
+	unsigned long clk;
+
+	cpu_sel = (ltq_cgu_r32(CGU_SYS_XRX) >> 4) & 0xf;
+
+	switch (cpu_sel) {
+	case 0:
+		clk = CLOCK_600M;
+		break;
+	case 1:
+		clk = CLOCK_500M;
+		break;
+	case 2:
+		clk = CLOCK_393M;
+		break;
+	case 3:
+		clk = CLOCK_333M;
+		break;
+	case 5:
+	case 6:
+		clk = CLOCK_196_608M;
+		break;
+	case 7:
+		clk = CLOCK_167M;
+		break;
+	case 4:
+	case 8:
+	case 9:
+		clk = CLOCK_125M;
+		break;
+	default:
+		clk = 0;
+		break;
+	}
+
+	return clk;
+}
+
+unsigned long ltq_vr9_fpi_hz(void)
+{
+	unsigned int ocp_sel, cpu_clk;
+	unsigned long clk;
+
+	cpu_clk = ltq_vr9_cpu_hz();
+	ocp_sel = ltq_cgu_r32(CGU_SYS_XRX) & 0x3;
+
+	switch (ocp_sel) {
+	case 0:
+		/* OCP ratio 1 */
+		clk = cpu_clk;
+		break;
+	case 2:
+		/* OCP ratio 2 */
+		clk = cpu_clk / 2;
+		break;
+	case 3:
+		/* OCP ratio 2.5 */
+		clk = (cpu_clk * 2) / 5;
+		break;
+	case 4:
+		/* OCP ratio 3 */
+		clk = cpu_clk / 3;
+		break;
+	default:
+		clk = 0;
+		break;
+	}
+
+	return clk;
+}
+
+unsigned long ltq_vr9_pp32_hz(void)
+{
+	unsigned int clksys = (ltq_cgu_r32(CGU_SYS) >> 16) & 0x7;
+	unsigned long clk;
+
+	switch (clksys) {
+	case 0:
+		clk = CLOCK_500M;
+		break;
+	case 1:
+		clk = CLOCK_432M;
+		break;
+	case 2:
+		clk = CLOCK_288M;
+		break;
+	default:
+		clk = CLOCK_500M;
+		break;
+	}
+
+	return clk;
+}
+
+unsigned long ltq_ar10_cpu_hz(void)
+{
+	unsigned int clksys;
+	int cpu_fs = (ltq_cgu_r32(CGU_SYS_XRX) >> 8) & 0x1;
+	int freq_div = (ltq_cgu_r32(CGU_SYS_XRX) >> 4) & 0x7;
+
+	switch (cpu_fs) {
+	case 0:
+		clksys = CLOCK_500M;
+		break;
+	case 1:
+		clksys = CLOCK_600M;
+		break;
+	default:
+		clksys = CLOCK_500M;
+		break;
+	}
+
+	switch (freq_div) {
+	case 0:
+		return clksys;
+	case 1:
+		return clksys >> 1;
+	case 2:
+		return clksys >> 2;
+	default:
+		return clksys;
+	}
+}
+
+unsigned long ltq_ar10_fpi_hz(void)
+{
+	int freq_fpi = (ltq_cgu_r32(CGU_IF_CLK_AR10) >> 25) & 0xf;
+
+	switch (freq_fpi) {
+	case 1:
+		return CLOCK_300M;
+	case 5:
+		return CLOCK_250M;
+	case 2:
+		return CLOCK_150M;
+	case 6:
+		return CLOCK_125M;
+
+	default:
+		return CLOCK_125M;
+	}
+}
+
+unsigned long ltq_ar10_pp32_hz(void)
+{
+	unsigned int clksys = (ltq_cgu_r32(CGU_SYS) >> 16) & 0x7;
+	unsigned long clk;
+
+	switch (clksys) {
+	case 1:
+		clk = CLOCK_250M;
+		break;
+	case 4:
+		clk = CLOCK_400M;
+		break;
+	default:
+		clk = CLOCK_250M;
+		break;
+	}
+
+	return clk;
+}
+
+unsigned long ltq_grx390_cpu_hz(void)
+{
+	unsigned int clksys;
+	int cpu_fs = ((ltq_cgu_r32(CGU_SYS_XRX) >> 9) & 0x3);
+	int freq_div = ((ltq_cgu_r32(CGU_SYS_XRX) >> 4) & 0x7);
+
+	switch (cpu_fs) {
+	case 0:
+		clksys = CLOCK_600M;
+		break;
+	case 1:
+		clksys = CLOCK_666M;
+		break;
+	case 2:
+		clksys = CLOCK_720M;
+		break;
+	default:
+		clksys = CLOCK_600M;
+		break;
+	}
+
+	switch (freq_div) {
+	case 0:
+		return clksys;
+	case 1:
+		return clksys >> 1;
+	case 2:
+		return clksys >> 2;
+	default:
+		return clksys;
+	}
+}
+
+unsigned long ltq_grx390_fpi_hz(void)
+{
+	/* fpi clock is derived from ddr_clk */
+	unsigned int clksys;
+	int cpu_fs = ((ltq_cgu_r32(CGU_SYS_XRX) >> 9) & 0x3);
+	int freq_div = ((ltq_cgu_r32(CGU_SYS_XRX)) & 0x7);
+	switch (cpu_fs) {
+	case 0:
+		clksys = CLOCK_600M;
+		break;
+	case 1:
+		clksys = CLOCK_666M;
+		break;
+	case 2:
+		clksys = CLOCK_720M;
+		break;
+	default:
+		clksys = CLOCK_600M;
+		break;
+	}
+
+	switch (freq_div) {
+	case 1:
+		return clksys >> 1;
+	case 2:
+		return clksys >> 2;
+	default:
+		return clksys >> 1;
+	}
+}
+
+unsigned long ltq_grx390_pp32_hz(void)
+{
+	unsigned int clksys = (ltq_cgu_r32(CGU_SYS) >> 16) & 0x7;
+	unsigned long clk;
+
+	switch (clksys) {
+	case 1:
+		clk = CLOCK_250M;
+		break;
+	case 2:
+		clk = CLOCK_432M;
+		break;
+	case 4:
+		clk = CLOCK_400M;
+		break;
+	default:
+		clk = CLOCK_250M;
+		break;
+	}
+	return clk;
+}
diff --git a/arch/mips/lantiq/xway/dcdc.c b/arch/mips/lantiq/xway/dcdc.c
new file mode 100644
index 000000000..4960bee0a
--- /dev/null
+++ b/arch/mips/lantiq/xway/dcdc.c
@@ -0,0 +1,60 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ *  Copyright (C) 2012 John Crispin <john@phrozen.org>
+ *  Copyright (C) 2010 Sameer Ahmad, Lantiq GmbH
+ */
+
+#include <linux/ioport.h>
+#include <linux/of_platform.h>
+
+#include <lantiq_soc.h>
+
+/* Bias and regulator Setup Register */
+#define DCDC_BIAS_VREG0	0xa
+/* Bias and regulator Setup Register */
+#define DCDC_BIAS_VREG1	0xb
+
+#define dcdc_w8(x, y)	ltq_w8((x), dcdc_membase + (y))
+#define dcdc_r8(x)	ltq_r8(dcdc_membase + (x))
+
+static void __iomem *dcdc_membase;
+
+static int dcdc_probe(struct platform_device *pdev)
+{
+	struct resource *res;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	dcdc_membase = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(dcdc_membase))
+		return PTR_ERR(dcdc_membase);
+
+	dev_info(&pdev->dev, "Core Voltage : %d mV\n",
+		dcdc_r8(DCDC_BIAS_VREG1) * 8);
+
+	return 0;
+}
+
+static const struct of_device_id dcdc_match[] = {
+	{ .compatible = "lantiq,dcdc-xrx200" },
+	{},
+};
+
+static struct platform_driver dcdc_driver = {
+	.probe = dcdc_probe,
+	.driver = {
+		.name = "dcdc-xrx200",
+		.of_match_table = dcdc_match,
+	},
+};
+
+int __init dcdc_init(void)
+{
+	int ret = platform_driver_register(&dcdc_driver);
+
+	if (ret)
+		pr_info("dcdc: Error registering platform driver\n");
+	return ret;
+}
+
+arch_initcall(dcdc_init);
diff --git a/arch/mips/lantiq/xway/dma.c b/arch/mips/lantiq/xway/dma.c
new file mode 100644
index 000000000..f8eedeb15
--- /dev/null
+++ b/arch/mips/lantiq/xway/dma.c
@@ -0,0 +1,300 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ *   Copyright (C) 2011 John Crispin <john@phrozen.org>
+ */
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/dma-mapping.h>
+#include <linux/export.h>
+#include <linux/spinlock.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/of.h>
+
+#include <lantiq_soc.h>
+#include <xway_dma.h>
+
+#define LTQ_DMA_ID		0x08
+#define LTQ_DMA_CTRL		0x10
+#define LTQ_DMA_CPOLL		0x14
+#define LTQ_DMA_CS		0x18
+#define LTQ_DMA_CCTRL		0x1C
+#define LTQ_DMA_CDBA		0x20
+#define LTQ_DMA_CDLEN		0x24
+#define LTQ_DMA_CIS		0x28
+#define LTQ_DMA_CIE		0x2C
+#define LTQ_DMA_PS		0x40
+#define LTQ_DMA_PCTRL		0x44
+#define LTQ_DMA_IRNEN		0xf4
+
+#define DMA_ID_CHNR		GENMASK(26, 20)	/* channel number */
+#define DMA_DESCPT		BIT(3)		/* descriptor complete irq */
+#define DMA_TX			BIT(8)		/* TX channel direction */
+#define DMA_CHAN_ON		BIT(0)		/* channel on / off bit */
+#define DMA_PDEN		BIT(6)		/* enable packet drop */
+#define DMA_CHAN_RST		BIT(1)		/* channel on / off bit */
+#define DMA_RESET		BIT(0)		/* channel on / off bit */
+#define DMA_IRQ_ACK		0x7e		/* IRQ status register */
+#define DMA_POLL		BIT(31)		/* turn on channel polling */
+#define DMA_CLK_DIV4		BIT(6)		/* polling clock divider */
+#define DMA_PCTRL_2W_BURST	0x1		/* 2 word burst length */
+#define DMA_PCTRL_4W_BURST	0x2		/* 4 word burst length */
+#define DMA_PCTRL_8W_BURST	0x3		/* 8 word burst length */
+#define DMA_TX_BURST_SHIFT	4		/* tx burst shift */
+#define DMA_RX_BURST_SHIFT	2		/* rx burst shift */
+#define DMA_ETOP_ENDIANNESS	(0xf << 8) /* endianness swap etop channels */
+#define DMA_WEIGHT	(BIT(17) | BIT(16))	/* default channel wheight */
+
+#define ltq_dma_r32(x)			ltq_r32(ltq_dma_membase + (x))
+#define ltq_dma_w32(x, y)		ltq_w32(x, ltq_dma_membase + (y))
+#define ltq_dma_w32_mask(x, y, z)	ltq_w32_mask(x, y, \
+						ltq_dma_membase + (z))
+
+static void __iomem *ltq_dma_membase;
+static DEFINE_SPINLOCK(ltq_dma_lock);
+
+void
+ltq_dma_enable_irq(struct ltq_dma_channel *ch)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&ltq_dma_lock, flags);
+	ltq_dma_w32(ch->nr, LTQ_DMA_CS);
+	ltq_dma_w32_mask(0, 1 << ch->nr, LTQ_DMA_IRNEN);
+	spin_unlock_irqrestore(&ltq_dma_lock, flags);
+}
+EXPORT_SYMBOL_GPL(ltq_dma_enable_irq);
+
+void
+ltq_dma_disable_irq(struct ltq_dma_channel *ch)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&ltq_dma_lock, flags);
+	ltq_dma_w32(ch->nr, LTQ_DMA_CS);
+	ltq_dma_w32_mask(1 << ch->nr, 0, LTQ_DMA_IRNEN);
+	spin_unlock_irqrestore(&ltq_dma_lock, flags);
+}
+EXPORT_SYMBOL_GPL(ltq_dma_disable_irq);
+
+void
+ltq_dma_ack_irq(struct ltq_dma_channel *ch)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&ltq_dma_lock, flags);
+	ltq_dma_w32(ch->nr, LTQ_DMA_CS);
+	ltq_dma_w32(DMA_IRQ_ACK, LTQ_DMA_CIS);
+	spin_unlock_irqrestore(&ltq_dma_lock, flags);
+}
+EXPORT_SYMBOL_GPL(ltq_dma_ack_irq);
+
+void
+ltq_dma_open(struct ltq_dma_channel *ch)
+{
+	unsigned long flag;
+
+	spin_lock_irqsave(&ltq_dma_lock, flag);
+	ltq_dma_w32(ch->nr, LTQ_DMA_CS);
+	ltq_dma_w32_mask(0, DMA_CHAN_ON, LTQ_DMA_CCTRL);
+	spin_unlock_irqrestore(&ltq_dma_lock, flag);
+}
+EXPORT_SYMBOL_GPL(ltq_dma_open);
+
+void
+ltq_dma_close(struct ltq_dma_channel *ch)
+{
+	unsigned long flag;
+
+	spin_lock_irqsave(&ltq_dma_lock, flag);
+	ltq_dma_w32(ch->nr, LTQ_DMA_CS);
+	ltq_dma_w32_mask(DMA_CHAN_ON, 0, LTQ_DMA_CCTRL);
+	ltq_dma_w32_mask(1 << ch->nr, 0, LTQ_DMA_IRNEN);
+	spin_unlock_irqrestore(&ltq_dma_lock, flag);
+}
+EXPORT_SYMBOL_GPL(ltq_dma_close);
+
+static void
+ltq_dma_alloc(struct ltq_dma_channel *ch)
+{
+	unsigned long flags;
+
+	ch->desc = 0;
+	ch->desc_base = dma_alloc_coherent(ch->dev,
+					   LTQ_DESC_NUM * LTQ_DESC_SIZE,
+					   &ch->phys, GFP_ATOMIC);
+
+	spin_lock_irqsave(&ltq_dma_lock, flags);
+	ltq_dma_w32(ch->nr, LTQ_DMA_CS);
+	ltq_dma_w32(ch->phys, LTQ_DMA_CDBA);
+	ltq_dma_w32(LTQ_DESC_NUM, LTQ_DMA_CDLEN);
+	ltq_dma_w32_mask(DMA_CHAN_ON, 0, LTQ_DMA_CCTRL);
+	wmb();
+	ltq_dma_w32_mask(0, DMA_CHAN_RST, LTQ_DMA_CCTRL);
+	while (ltq_dma_r32(LTQ_DMA_CCTRL) & DMA_CHAN_RST)
+		;
+	spin_unlock_irqrestore(&ltq_dma_lock, flags);
+}
+
+void
+ltq_dma_alloc_tx(struct ltq_dma_channel *ch)
+{
+	unsigned long flags;
+
+	ltq_dma_alloc(ch);
+
+	spin_lock_irqsave(&ltq_dma_lock, flags);
+	ltq_dma_w32(DMA_DESCPT, LTQ_DMA_CIE);
+	ltq_dma_w32_mask(0, 1 << ch->nr, LTQ_DMA_IRNEN);
+	ltq_dma_w32(DMA_WEIGHT | DMA_TX, LTQ_DMA_CCTRL);
+	spin_unlock_irqrestore(&ltq_dma_lock, flags);
+}
+EXPORT_SYMBOL_GPL(ltq_dma_alloc_tx);
+
+void
+ltq_dma_alloc_rx(struct ltq_dma_channel *ch)
+{
+	unsigned long flags;
+
+	ltq_dma_alloc(ch);
+
+	spin_lock_irqsave(&ltq_dma_lock, flags);
+	ltq_dma_w32(DMA_DESCPT, LTQ_DMA_CIE);
+	ltq_dma_w32_mask(0, 1 << ch->nr, LTQ_DMA_IRNEN);
+	ltq_dma_w32(DMA_WEIGHT, LTQ_DMA_CCTRL);
+	spin_unlock_irqrestore(&ltq_dma_lock, flags);
+}
+EXPORT_SYMBOL_GPL(ltq_dma_alloc_rx);
+
+void
+ltq_dma_free(struct ltq_dma_channel *ch)
+{
+	if (!ch->desc_base)
+		return;
+	ltq_dma_close(ch);
+	dma_free_coherent(ch->dev, LTQ_DESC_NUM * LTQ_DESC_SIZE,
+		ch->desc_base, ch->phys);
+}
+EXPORT_SYMBOL_GPL(ltq_dma_free);
+
+void
+ltq_dma_init_port(int p, int tx_burst, int rx_burst)
+{
+	ltq_dma_w32(p, LTQ_DMA_PS);
+	switch (p) {
+	case DMA_PORT_ETOP:
+		/*
+		 * Tell the DMA engine to swap the endianness of data frames and
+		 * drop packets if the channel arbitration fails.
+		 */
+		ltq_dma_w32_mask(0, (DMA_ETOP_ENDIANNESS | DMA_PDEN),
+			LTQ_DMA_PCTRL);
+		break;
+
+	default:
+		break;
+	}
+
+	switch (rx_burst) {
+	case 8:
+		ltq_dma_w32_mask(0x0c, (DMA_PCTRL_8W_BURST << DMA_RX_BURST_SHIFT),
+			LTQ_DMA_PCTRL);
+		break;
+	case 4:
+		ltq_dma_w32_mask(0x0c, (DMA_PCTRL_4W_BURST << DMA_RX_BURST_SHIFT),
+			LTQ_DMA_PCTRL);
+		break;
+	case 2:
+		ltq_dma_w32_mask(0x0c, (DMA_PCTRL_2W_BURST << DMA_RX_BURST_SHIFT),
+			LTQ_DMA_PCTRL);
+		break;
+	default:
+		break;
+	}
+
+	switch (tx_burst) {
+	case 8:
+		ltq_dma_w32_mask(0x30, (DMA_PCTRL_8W_BURST << DMA_TX_BURST_SHIFT),
+			LTQ_DMA_PCTRL);
+		break;
+	case 4:
+		ltq_dma_w32_mask(0x30, (DMA_PCTRL_4W_BURST << DMA_TX_BURST_SHIFT),
+			LTQ_DMA_PCTRL);
+		break;
+	case 2:
+		ltq_dma_w32_mask(0x30, (DMA_PCTRL_2W_BURST << DMA_TX_BURST_SHIFT),
+			LTQ_DMA_PCTRL);
+		break;
+	default:
+		break;
+	}
+}
+EXPORT_SYMBOL_GPL(ltq_dma_init_port);
+
+static int
+ltq_dma_init(struct platform_device *pdev)
+{
+	struct clk *clk;
+	struct resource *res;
+	unsigned int id, nchannels;
+	int i;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	ltq_dma_membase = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(ltq_dma_membase))
+		panic("Failed to remap dma resource");
+
+	/* power up and reset the dma engine */
+	clk = clk_get(&pdev->dev, NULL);
+	if (IS_ERR(clk))
+		panic("Failed to get dma clock");
+
+	clk_enable(clk);
+	ltq_dma_w32_mask(0, DMA_RESET, LTQ_DMA_CTRL);
+
+	usleep_range(1, 10);
+
+	/* disable all interrupts */
+	ltq_dma_w32(0, LTQ_DMA_IRNEN);
+
+	/* reset/configure each channel */
+	id = ltq_dma_r32(LTQ_DMA_ID);
+	nchannels = ((id & DMA_ID_CHNR) >> 20);
+	for (i = 0; i < nchannels; i++) {
+		ltq_dma_w32(i, LTQ_DMA_CS);
+		ltq_dma_w32(DMA_CHAN_RST, LTQ_DMA_CCTRL);
+		ltq_dma_w32(DMA_POLL | DMA_CLK_DIV4, LTQ_DMA_CPOLL);
+		ltq_dma_w32_mask(DMA_CHAN_ON, 0, LTQ_DMA_CCTRL);
+	}
+
+	dev_info(&pdev->dev,
+		"Init done - hw rev: %X, ports: %d, channels: %d\n",
+		id & 0x1f, (id >> 16) & 0xf, nchannels);
+
+	return 0;
+}
+
+static const struct of_device_id dma_match[] = {
+	{ .compatible = "lantiq,dma-xway" },
+	{},
+};
+
+static struct platform_driver dma_driver = {
+	.probe = ltq_dma_init,
+	.driver = {
+		.name = "dma-xway",
+		.of_match_table = dma_match,
+	},
+};
+
+int __init
+dma_init(void)
+{
+	return platform_driver_register(&dma_driver);
+}
+
+postcore_initcall(dma_init);
diff --git a/arch/mips/lantiq/xway/gptu.c b/arch/mips/lantiq/xway/gptu.c
new file mode 100644
index 000000000..200fe9ff6
--- /dev/null
+++ b/arch/mips/lantiq/xway/gptu.c
@@ -0,0 +1,208 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ *  Copyright (C) 2012 John Crispin <john@phrozen.org>
+ *  Copyright (C) 2012 Lantiq GmbH
+ */
+
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/init.h>
+#include <linux/of_platform.h>
+#include <linux/of_irq.h>
+
+#include <lantiq_soc.h>
+#include "../clk.h"
+
+/* the magic ID byte of the core */
+#define GPTU_MAGIC	0x59
+/* clock control register */
+#define GPTU_CLC	0x00
+/* id register */
+#define GPTU_ID		0x08
+/* interrupt node enable */
+#define GPTU_IRNEN	0xf4
+/* interrupt control register */
+#define GPTU_IRCR	0xf8
+/* interrupt capture register */
+#define GPTU_IRNCR	0xfc
+/* there are 3 identical blocks of 2 timers. calculate register offsets */
+#define GPTU_SHIFT(x)	(x % 2 ? 4 : 0)
+#define GPTU_BASE(x)	(((x >> 1) * 0x20) + 0x10)
+/* timer control register */
+#define GPTU_CON(x)	(GPTU_BASE(x) + GPTU_SHIFT(x) + 0x00)
+/* timer auto reload register */
+#define GPTU_RUN(x)	(GPTU_BASE(x) + GPTU_SHIFT(x) + 0x08)
+/* timer manual reload register */
+#define GPTU_RLD(x)	(GPTU_BASE(x) + GPTU_SHIFT(x) + 0x10)
+/* timer count register */
+#define GPTU_CNT(x)	(GPTU_BASE(x) + GPTU_SHIFT(x) + 0x18)
+
+/* GPTU_CON(x) */
+#define CON_CNT		BIT(2)
+#define CON_EDGE_ANY	(BIT(7) | BIT(6))
+#define CON_SYNC	BIT(8)
+#define CON_CLK_INT	BIT(10)
+
+/* GPTU_RUN(x) */
+#define RUN_SEN		BIT(0)
+#define RUN_RL		BIT(2)
+
+/* set clock to runmode */
+#define CLC_RMC		BIT(8)
+/* bring core out of suspend */
+#define CLC_SUSPEND	BIT(4)
+/* the disable bit */
+#define CLC_DISABLE	BIT(0)
+
+#define gptu_w32(x, y)	ltq_w32((x), gptu_membase + (y))
+#define gptu_r32(x)	ltq_r32(gptu_membase + (x))
+
+enum gptu_timer {
+	TIMER1A = 0,
+	TIMER1B,
+	TIMER2A,
+	TIMER2B,
+	TIMER3A,
+	TIMER3B
+};
+
+static void __iomem *gptu_membase;
+static struct resource irqres[6];
+
+static irqreturn_t timer_irq_handler(int irq, void *priv)
+{
+	int timer = irq - irqres[0].start;
+	gptu_w32(1 << timer, GPTU_IRNCR);
+	return IRQ_HANDLED;
+}
+
+static void gptu_hwinit(void)
+{
+	gptu_w32(0x00, GPTU_IRNEN);
+	gptu_w32(0xff, GPTU_IRNCR);
+	gptu_w32(CLC_RMC | CLC_SUSPEND, GPTU_CLC);
+}
+
+static void gptu_hwexit(void)
+{
+	gptu_w32(0x00, GPTU_IRNEN);
+	gptu_w32(0xff, GPTU_IRNCR);
+	gptu_w32(CLC_DISABLE, GPTU_CLC);
+}
+
+static int gptu_enable(struct clk *clk)
+{
+	int ret = request_irq(irqres[clk->bits].start, timer_irq_handler,
+		IRQF_TIMER, "gtpu", NULL);
+	if (ret) {
+		pr_err("gptu: failed to request irq\n");
+		return ret;
+	}
+
+	gptu_w32(CON_CNT | CON_EDGE_ANY | CON_SYNC | CON_CLK_INT,
+		GPTU_CON(clk->bits));
+	gptu_w32(1, GPTU_RLD(clk->bits));
+	gptu_w32(gptu_r32(GPTU_IRNEN) | BIT(clk->bits), GPTU_IRNEN);
+	gptu_w32(RUN_SEN | RUN_RL, GPTU_RUN(clk->bits));
+	return 0;
+}
+
+static void gptu_disable(struct clk *clk)
+{
+	gptu_w32(0, GPTU_RUN(clk->bits));
+	gptu_w32(0, GPTU_CON(clk->bits));
+	gptu_w32(0, GPTU_RLD(clk->bits));
+	gptu_w32(gptu_r32(GPTU_IRNEN) & ~BIT(clk->bits), GPTU_IRNEN);
+	free_irq(irqres[clk->bits].start, NULL);
+}
+
+static inline void clkdev_add_gptu(struct device *dev, const char *con,
+							unsigned int timer)
+{
+	struct clk *clk = kzalloc(sizeof(struct clk), GFP_KERNEL);
+
+	if (!clk)
+		return;
+	clk->cl.dev_id = dev_name(dev);
+	clk->cl.con_id = con;
+	clk->cl.clk = clk;
+	clk->enable = gptu_enable;
+	clk->disable = gptu_disable;
+	clk->bits = timer;
+	clkdev_add(&clk->cl);
+}
+
+static int gptu_probe(struct platform_device *pdev)
+{
+	struct clk *clk;
+	struct resource *res;
+
+	if (of_irq_to_resource_table(pdev->dev.of_node, irqres, 6) != 6) {
+		dev_err(&pdev->dev, "Failed to get IRQ list\n");
+		return -EINVAL;
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+
+	/* remap gptu register range */
+	gptu_membase = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(gptu_membase))
+		return PTR_ERR(gptu_membase);
+
+	/* enable our clock */
+	clk = clk_get(&pdev->dev, NULL);
+	if (IS_ERR(clk)) {
+		dev_err(&pdev->dev, "Failed to get clock\n");
+		return -ENOENT;
+	}
+	clk_enable(clk);
+
+	/* power up the core */
+	gptu_hwinit();
+
+	/* the gptu has a ID register */
+	if (((gptu_r32(GPTU_ID) >> 8) & 0xff) != GPTU_MAGIC) {
+		dev_err(&pdev->dev, "Failed to find magic\n");
+		gptu_hwexit();
+		clk_disable(clk);
+		clk_put(clk);
+		return -ENAVAIL;
+	}
+
+	/* register the clocks */
+	clkdev_add_gptu(&pdev->dev, "timer1a", TIMER1A);
+	clkdev_add_gptu(&pdev->dev, "timer1b", TIMER1B);
+	clkdev_add_gptu(&pdev->dev, "timer2a", TIMER2A);
+	clkdev_add_gptu(&pdev->dev, "timer2b", TIMER2B);
+	clkdev_add_gptu(&pdev->dev, "timer3a", TIMER3A);
+	clkdev_add_gptu(&pdev->dev, "timer3b", TIMER3B);
+
+	dev_info(&pdev->dev, "gptu: 6 timers loaded\n");
+
+	return 0;
+}
+
+static const struct of_device_id gptu_match[] = {
+	{ .compatible = "lantiq,gptu-xway" },
+	{},
+};
+
+static struct platform_driver dma_driver = {
+	.probe = gptu_probe,
+	.driver = {
+		.name = "gptu-xway",
+		.of_match_table = gptu_match,
+	},
+};
+
+int __init gptu_init(void)
+{
+	int ret = platform_driver_register(&dma_driver);
+
+	if (ret)
+		pr_info("gptu: Error registering platform driver\n");
+	return ret;
+}
+
+arch_initcall(gptu_init);
diff --git a/arch/mips/lantiq/xway/prom.c b/arch/mips/lantiq/xway/prom.c
new file mode 100644
index 000000000..544619754
--- /dev/null
+++ b/arch/mips/lantiq/xway/prom.c
@@ -0,0 +1,144 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ *  Copyright (C) 2010 John Crispin <john@phrozen.org>
+ *  Copyright (C) 2013-2015 Lantiq Beteiligungs-GmbH & Co.KG
+ */
+
+#include <linux/export.h>
+#include <linux/clk.h>
+#include <asm/bootinfo.h>
+#include <asm/time.h>
+
+#include <lantiq_soc.h>
+
+#include "../prom.h"
+
+#define SOC_DANUBE	"Danube"
+#define SOC_TWINPASS	"Twinpass"
+#define SOC_AMAZON_SE	"Amazon_SE"
+#define SOC_AR9		"AR9"
+#define SOC_GR9		"GRX200"
+#define SOC_VR9		"xRX200"
+#define SOC_VRX220	"xRX220"
+#define SOC_AR10	"xRX300"
+#define SOC_GRX390	"xRX330"
+
+#define COMP_DANUBE	"lantiq,danube"
+#define COMP_TWINPASS	"lantiq,twinpass"
+#define COMP_AMAZON_SE	"lantiq,ase"
+#define COMP_AR9	"lantiq,ar9"
+#define COMP_GR9	"lantiq,gr9"
+#define COMP_VR9	"lantiq,vr9"
+#define COMP_AR10	"lantiq,ar10"
+#define COMP_GRX390	"lantiq,grx390"
+
+#define PART_SHIFT	12
+#define PART_MASK	0x0FFFFFFF
+#define REV_SHIFT	28
+#define REV_MASK	0xF0000000
+
+void __init ltq_soc_detect(struct ltq_soc_info *i)
+{
+	i->partnum = (ltq_r32(LTQ_MPS_CHIPID) & PART_MASK) >> PART_SHIFT;
+	i->rev = (ltq_r32(LTQ_MPS_CHIPID) & REV_MASK) >> REV_SHIFT;
+	sprintf(i->rev_type, "1.%d", i->rev);
+	switch (i->partnum) {
+	case SOC_ID_DANUBE1:
+	case SOC_ID_DANUBE2:
+		i->name = SOC_DANUBE;
+		i->type = SOC_TYPE_DANUBE;
+		i->compatible = COMP_DANUBE;
+		break;
+
+	case SOC_ID_TWINPASS:
+		i->name = SOC_TWINPASS;
+		i->type = SOC_TYPE_DANUBE;
+		i->compatible = COMP_TWINPASS;
+		break;
+
+	case SOC_ID_ARX188:
+	case SOC_ID_ARX168_1:
+	case SOC_ID_ARX168_2:
+	case SOC_ID_ARX182:
+		i->name = SOC_AR9;
+		i->type = SOC_TYPE_AR9;
+		i->compatible = COMP_AR9;
+		break;
+
+	case SOC_ID_GRX188:
+	case SOC_ID_GRX168:
+		i->name = SOC_GR9;
+		i->type = SOC_TYPE_AR9;
+		i->compatible = COMP_GR9;
+		break;
+
+	case SOC_ID_AMAZON_SE_1:
+	case SOC_ID_AMAZON_SE_2:
+#ifdef CONFIG_PCI
+		panic("ase is only supported for non pci kernels");
+#endif
+		i->name = SOC_AMAZON_SE;
+		i->type = SOC_TYPE_AMAZON_SE;
+		i->compatible = COMP_AMAZON_SE;
+		break;
+
+	case SOC_ID_VRX282:
+	case SOC_ID_VRX268:
+	case SOC_ID_VRX288:
+		i->name = SOC_VR9;
+		i->type = SOC_TYPE_VR9;
+		i->compatible = COMP_VR9;
+		break;
+
+	case SOC_ID_GRX268:
+	case SOC_ID_GRX288:
+		i->name = SOC_GR9;
+		i->type = SOC_TYPE_VR9;
+		i->compatible = COMP_GR9;
+		break;
+
+	case SOC_ID_VRX268_2:
+	case SOC_ID_VRX288_2:
+		i->name = SOC_VR9;
+		i->type = SOC_TYPE_VR9_2;
+		i->compatible = COMP_VR9;
+		break;
+
+	case SOC_ID_VRX220:
+		i->name = SOC_VRX220;
+		i->type = SOC_TYPE_VRX220;
+		i->compatible = COMP_VR9;
+		break;
+
+	case SOC_ID_GRX282_2:
+	case SOC_ID_GRX288_2:
+		i->name = SOC_GR9;
+		i->type = SOC_TYPE_VR9_2;
+		i->compatible = COMP_GR9;
+		break;
+
+	case SOC_ID_ARX362:
+	case SOC_ID_ARX368:
+	case SOC_ID_ARX382:
+	case SOC_ID_ARX388:
+	case SOC_ID_URX388:
+		i->name = SOC_AR10;
+		i->type = SOC_TYPE_AR10;
+		i->compatible = COMP_AR10;
+		break;
+
+	case SOC_ID_GRX383:
+	case SOC_ID_GRX369:
+	case SOC_ID_GRX387:
+	case SOC_ID_GRX389:
+		i->name = SOC_GRX390;
+		i->type = SOC_TYPE_GRX390;
+		i->compatible = COMP_GRX390;
+		break;
+
+	default:
+		unreachable();
+		break;
+	}
+}
diff --git a/arch/mips/lantiq/xway/sysctrl.c b/arch/mips/lantiq/xway/sysctrl.c
new file mode 100644
index 000000000..d444a1b98
--- /dev/null
+++ b/arch/mips/lantiq/xway/sysctrl.c
@@ -0,0 +1,592 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ *  Copyright (C) 2011-2012 John Crispin <john@phrozen.org>
+ *  Copyright (C) 2013-2015 Lantiq Beteiligungs-GmbH & Co.KG
+ */
+
+#include <linux/ioport.h>
+#include <linux/export.h>
+#include <linux/clkdev.h>
+#include <linux/spinlock.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/of_address.h>
+
+#include <lantiq_soc.h>
+
+#include "../clk.h"
+#include "../prom.h"
+
+/* clock control register for legacy */
+#define CGU_IFCCR	0x0018
+#define CGU_IFCCR_VR9	0x0024
+/* system clock register for legacy */
+#define CGU_SYS		0x0010
+/* pci control register */
+#define CGU_PCICR	0x0034
+#define CGU_PCICR_VR9	0x0038
+/* ephy configuration register */
+#define CGU_EPHY	0x10
+
+/* Legacy PMU register for ar9, ase, danube */
+/* power control register */
+#define PMU_PWDCR	0x1C
+/* power status register */
+#define PMU_PWDSR	0x20
+/* power control register */
+#define PMU_PWDCR1	0x24
+/* power status register */
+#define PMU_PWDSR1	0x28
+/* power control register */
+#define PWDCR(x) ((x) ? (PMU_PWDCR1) : (PMU_PWDCR))
+/* power status register */
+#define PWDSR(x) ((x) ? (PMU_PWDSR1) : (PMU_PWDSR))
+
+
+/* PMU register for ar10 and grx390 */
+
+/* First register set */
+#define PMU_CLK_SR	0x20 /* status */
+#define PMU_CLK_CR_A	0x24 /* Enable */
+#define PMU_CLK_CR_B	0x28 /* Disable */
+/* Second register set */
+#define PMU_CLK_SR1	0x30 /* status */
+#define PMU_CLK_CR1_A	0x34 /* Enable */
+#define PMU_CLK_CR1_B	0x38 /* Disable */
+/* Third register set */
+#define PMU_ANA_SR	0x40 /* status */
+#define PMU_ANA_CR_A	0x44 /* Enable */
+#define PMU_ANA_CR_B	0x48 /* Disable */
+
+/* Status */
+static u32 pmu_clk_sr[] = {
+	PMU_CLK_SR,
+	PMU_CLK_SR1,
+	PMU_ANA_SR,
+};
+
+/* Enable */
+static u32 pmu_clk_cr_a[] = {
+	PMU_CLK_CR_A,
+	PMU_CLK_CR1_A,
+	PMU_ANA_CR_A,
+};
+
+/* Disable */
+static u32 pmu_clk_cr_b[] = {
+	PMU_CLK_CR_B,
+	PMU_CLK_CR1_B,
+	PMU_ANA_CR_B,
+};
+
+#define PWDCR_EN_XRX(x)		(pmu_clk_cr_a[(x)])
+#define PWDCR_DIS_XRX(x)	(pmu_clk_cr_b[(x)])
+#define PWDSR_XRX(x)		(pmu_clk_sr[(x)])
+
+/* clock gates that we can en/disable */
+#define PMU_USB0_P	BIT(0)
+#define PMU_ASE_SDIO	BIT(2) /* ASE special */
+#define PMU_PCI		BIT(4)
+#define PMU_DMA		BIT(5)
+#define PMU_USB0	BIT(6)
+#define PMU_ASC0	BIT(7)
+#define PMU_EPHY	BIT(7)	/* ase */
+#define PMU_USIF	BIT(7) /* from vr9 until grx390 */
+#define PMU_SPI		BIT(8)
+#define PMU_DFE		BIT(9)
+#define PMU_EBU		BIT(10)
+#define PMU_STP		BIT(11)
+#define PMU_GPT		BIT(12)
+#define PMU_AHBS	BIT(13) /* vr9 */
+#define PMU_FPI		BIT(14)
+#define PMU_AHBM	BIT(15)
+#define PMU_SDIO	BIT(16) /* danube, ar9, vr9 */
+#define PMU_ASC1	BIT(17)
+#define PMU_PPE_QSB	BIT(18)
+#define PMU_PPE_SLL01	BIT(19)
+#define PMU_DEU		BIT(20)
+#define PMU_PPE_TC	BIT(21)
+#define PMU_PPE_EMA	BIT(22)
+#define PMU_PPE_DPLUM	BIT(23)
+#define PMU_PPE_DP	BIT(23)
+#define PMU_PPE_DPLUS	BIT(24)
+#define PMU_USB1_P	BIT(26)
+#define PMU_GPHY3	BIT(26) /* grx390 */
+#define PMU_USB1	BIT(27)
+#define PMU_SWITCH	BIT(28)
+#define PMU_PPE_TOP	BIT(29)
+#define PMU_GPHY0	BIT(29) /* ar10, xrx390 */
+#define PMU_GPHY	BIT(30)
+#define PMU_GPHY1	BIT(30) /* ar10, xrx390 */
+#define PMU_PCIE_CLK	BIT(31)
+#define PMU_GPHY2	BIT(31) /* ar10, xrx390 */
+
+#define PMU1_PCIE_PHY	BIT(0)	/* vr9-specific,moved in ar10/grx390 */
+#define PMU1_PCIE_CTL	BIT(1)
+#define PMU1_PCIE_PDI	BIT(4)
+#define PMU1_PCIE_MSI	BIT(5)
+#define PMU1_CKE	BIT(6)
+#define PMU1_PCIE1_CTL	BIT(17)
+#define PMU1_PCIE1_PDI	BIT(20)
+#define PMU1_PCIE1_MSI	BIT(21)
+#define PMU1_PCIE2_CTL	BIT(25)
+#define PMU1_PCIE2_PDI	BIT(26)
+#define PMU1_PCIE2_MSI	BIT(27)
+
+#define PMU_ANALOG_USB0_P	BIT(0)
+#define PMU_ANALOG_USB1_P	BIT(1)
+#define PMU_ANALOG_PCIE0_P	BIT(8)
+#define PMU_ANALOG_PCIE1_P	BIT(9)
+#define PMU_ANALOG_PCIE2_P	BIT(10)
+#define PMU_ANALOG_DSL_AFE	BIT(16)
+#define PMU_ANALOG_DCDC_2V5	BIT(17)
+#define PMU_ANALOG_DCDC_1VX	BIT(18)
+#define PMU_ANALOG_DCDC_1V0	BIT(19)
+
+#define pmu_w32(x, y)	ltq_w32((x), pmu_membase + (y))
+#define pmu_r32(x)	ltq_r32(pmu_membase + (x))
+
+static void __iomem *pmu_membase;
+void __iomem *ltq_cgu_membase;
+void __iomem *ltq_ebu_membase;
+
+static u32 ifccr = CGU_IFCCR;
+static u32 pcicr = CGU_PCICR;
+
+static DEFINE_SPINLOCK(g_pmu_lock);
+
+/* legacy function kept alive to ease clkdev transition */
+void ltq_pmu_enable(unsigned int module)
+{
+	int retry = 1000000;
+
+	spin_lock(&g_pmu_lock);
+	pmu_w32(pmu_r32(PMU_PWDCR) & ~module, PMU_PWDCR);
+	do {} while (--retry && (pmu_r32(PMU_PWDSR) & module));
+	spin_unlock(&g_pmu_lock);
+
+	if (!retry)
+		panic("activating PMU module failed!");
+}
+EXPORT_SYMBOL(ltq_pmu_enable);
+
+/* legacy function kept alive to ease clkdev transition */
+void ltq_pmu_disable(unsigned int module)
+{
+	int retry = 1000000;
+
+	spin_lock(&g_pmu_lock);
+	pmu_w32(pmu_r32(PMU_PWDCR) | module, PMU_PWDCR);
+	do {} while (--retry && (!(pmu_r32(PMU_PWDSR) & module)));
+	spin_unlock(&g_pmu_lock);
+
+	if (!retry)
+		pr_warn("deactivating PMU module failed!");
+}
+EXPORT_SYMBOL(ltq_pmu_disable);
+
+/* enable a hw clock */
+static int cgu_enable(struct clk *clk)
+{
+	ltq_cgu_w32(ltq_cgu_r32(ifccr) | clk->bits, ifccr);
+	return 0;
+}
+
+/* disable a hw clock */
+static void cgu_disable(struct clk *clk)
+{
+	ltq_cgu_w32(ltq_cgu_r32(ifccr) & ~clk->bits, ifccr);
+}
+
+/* enable a clock gate */
+static int pmu_enable(struct clk *clk)
+{
+	int retry = 1000000;
+
+	if (of_machine_is_compatible("lantiq,ar10")
+	    || of_machine_is_compatible("lantiq,grx390")) {
+		pmu_w32(clk->bits, PWDCR_EN_XRX(clk->module));
+		do {} while (--retry &&
+			     (!(pmu_r32(PWDSR_XRX(clk->module)) & clk->bits)));
+
+	} else {
+		spin_lock(&g_pmu_lock);
+		pmu_w32(pmu_r32(PWDCR(clk->module)) & ~clk->bits,
+				PWDCR(clk->module));
+		do {} while (--retry &&
+			     (pmu_r32(PWDSR(clk->module)) & clk->bits));
+		spin_unlock(&g_pmu_lock);
+	}
+
+	if (!retry)
+		panic("activating PMU module failed!");
+
+	return 0;
+}
+
+/* disable a clock gate */
+static void pmu_disable(struct clk *clk)
+{
+	int retry = 1000000;
+
+	if (of_machine_is_compatible("lantiq,ar10")
+	    || of_machine_is_compatible("lantiq,grx390")) {
+		pmu_w32(clk->bits, PWDCR_DIS_XRX(clk->module));
+		do {} while (--retry &&
+			     (pmu_r32(PWDSR_XRX(clk->module)) & clk->bits));
+	} else {
+		spin_lock(&g_pmu_lock);
+		pmu_w32(pmu_r32(PWDCR(clk->module)) | clk->bits,
+				PWDCR(clk->module));
+		do {} while (--retry &&
+			     (!(pmu_r32(PWDSR(clk->module)) & clk->bits)));
+		spin_unlock(&g_pmu_lock);
+	}
+
+	if (!retry)
+		pr_warn("deactivating PMU module failed!");
+}
+
+/* the pci enable helper */
+static int pci_enable(struct clk *clk)
+{
+	unsigned int val = ltq_cgu_r32(ifccr);
+	/* set bus clock speed */
+	if (of_machine_is_compatible("lantiq,ar9") ||
+			of_machine_is_compatible("lantiq,vr9")) {
+		val &= ~0x1f00000;
+		if (clk->rate == CLOCK_33M)
+			val |= 0xe00000;
+		else
+			val |= 0x700000; /* 62.5M */
+	} else {
+		val &= ~0xf00000;
+		if (clk->rate == CLOCK_33M)
+			val |= 0x800000;
+		else
+			val |= 0x400000; /* 62.5M */
+	}
+	ltq_cgu_w32(val, ifccr);
+	pmu_enable(clk);
+	return 0;
+}
+
+/* enable the external clock as a source */
+static int pci_ext_enable(struct clk *clk)
+{
+	ltq_cgu_w32(ltq_cgu_r32(ifccr) & ~(1 << 16), ifccr);
+	ltq_cgu_w32((1 << 30), pcicr);
+	return 0;
+}
+
+/* disable the external clock as a source */
+static void pci_ext_disable(struct clk *clk)
+{
+	ltq_cgu_w32(ltq_cgu_r32(ifccr) | (1 << 16), ifccr);
+	ltq_cgu_w32((1 << 31) | (1 << 30), pcicr);
+}
+
+/* enable a clockout source */
+static int clkout_enable(struct clk *clk)
+{
+	int i;
+
+	/* get the correct rate */
+	for (i = 0; i < 4; i++) {
+		if (clk->rates[i] == clk->rate) {
+			int shift = 14 - (2 * clk->module);
+			int enable = 7 - clk->module;
+			unsigned int val = ltq_cgu_r32(ifccr);
+
+			val &= ~(3 << shift);
+			val |= i << shift;
+			val |= enable;
+			ltq_cgu_w32(val, ifccr);
+			return 0;
+		}
+	}
+	return -1;
+}
+
+/* manage the clock gates via PMU */
+static void clkdev_add_pmu(const char *dev, const char *con, bool deactivate,
+			   unsigned int module, unsigned int bits)
+{
+	struct clk *clk = kzalloc(sizeof(struct clk), GFP_KERNEL);
+
+	if (!clk)
+		return;
+	clk->cl.dev_id = dev;
+	clk->cl.con_id = con;
+	clk->cl.clk = clk;
+	clk->enable = pmu_enable;
+	clk->disable = pmu_disable;
+	clk->module = module;
+	clk->bits = bits;
+	if (deactivate) {
+		/*
+		 * Disable it during the initialization. Module should enable
+		 * when used
+		 */
+		pmu_disable(clk);
+	}
+	clkdev_add(&clk->cl);
+}
+
+/* manage the clock generator */
+static void clkdev_add_cgu(const char *dev, const char *con,
+					unsigned int bits)
+{
+	struct clk *clk = kzalloc(sizeof(struct clk), GFP_KERNEL);
+
+	if (!clk)
+		return;
+	clk->cl.dev_id = dev;
+	clk->cl.con_id = con;
+	clk->cl.clk = clk;
+	clk->enable = cgu_enable;
+	clk->disable = cgu_disable;
+	clk->bits = bits;
+	clkdev_add(&clk->cl);
+}
+
+/* pci needs its own enable function as the setup is a bit more complex */
+static unsigned long valid_pci_rates[] = {CLOCK_33M, CLOCK_62_5M, 0};
+
+static void clkdev_add_pci(void)
+{
+	struct clk *clk = kzalloc(sizeof(struct clk), GFP_KERNEL);
+	struct clk *clk_ext = kzalloc(sizeof(struct clk), GFP_KERNEL);
+
+	/* main pci clock */
+	if (clk) {
+		clk->cl.dev_id = "17000000.pci";
+		clk->cl.con_id = NULL;
+		clk->cl.clk = clk;
+		clk->rate = CLOCK_33M;
+		clk->rates = valid_pci_rates;
+		clk->enable = pci_enable;
+		clk->disable = pmu_disable;
+		clk->module = 0;
+		clk->bits = PMU_PCI;
+		clkdev_add(&clk->cl);
+	}
+
+	/* use internal/external bus clock */
+	if (clk_ext) {
+		clk_ext->cl.dev_id = "17000000.pci";
+		clk_ext->cl.con_id = "external";
+		clk_ext->cl.clk = clk_ext;
+		clk_ext->enable = pci_ext_enable;
+		clk_ext->disable = pci_ext_disable;
+		clkdev_add(&clk_ext->cl);
+	}
+}
+
+/* xway socs can generate clocks on gpio pins */
+static unsigned long valid_clkout_rates[4][5] = {
+	{CLOCK_32_768K, CLOCK_1_536M, CLOCK_2_5M, CLOCK_12M, 0},
+	{CLOCK_40M, CLOCK_12M, CLOCK_24M, CLOCK_48M, 0},
+	{CLOCK_25M, CLOCK_40M, CLOCK_30M, CLOCK_60M, 0},
+	{CLOCK_12M, CLOCK_50M, CLOCK_32_768K, CLOCK_25M, 0},
+};
+
+static void clkdev_add_clkout(void)
+{
+	int i;
+
+	for (i = 0; i < 4; i++) {
+		struct clk *clk;
+		char *name;
+
+		name = kzalloc(sizeof("clkout0"), GFP_KERNEL);
+		if (!name)
+			continue;
+		sprintf(name, "clkout%d", i);
+
+		clk = kzalloc(sizeof(struct clk), GFP_KERNEL);
+		if (!clk) {
+			kfree(name);
+			continue;
+		}
+		clk->cl.dev_id = "1f103000.cgu";
+		clk->cl.con_id = name;
+		clk->cl.clk = clk;
+		clk->rate = 0;
+		clk->rates = valid_clkout_rates[i];
+		clk->enable = clkout_enable;
+		clk->module = i;
+		clkdev_add(&clk->cl);
+	}
+}
+
+/* bring up all register ranges that we need for basic system control */
+void __init ltq_soc_init(void)
+{
+	struct resource res_pmu, res_cgu, res_ebu;
+	struct device_node *np_pmu =
+			of_find_compatible_node(NULL, NULL, "lantiq,pmu-xway");
+	struct device_node *np_cgu =
+			of_find_compatible_node(NULL, NULL, "lantiq,cgu-xway");
+	struct device_node *np_ebu =
+			of_find_compatible_node(NULL, NULL, "lantiq,ebu-xway");
+
+	/* check if all the core register ranges are available */
+	if (!np_pmu || !np_cgu || !np_ebu)
+		panic("Failed to load core nodes from devicetree");
+
+	if (of_address_to_resource(np_pmu, 0, &res_pmu) ||
+			of_address_to_resource(np_cgu, 0, &res_cgu) ||
+			of_address_to_resource(np_ebu, 0, &res_ebu))
+		panic("Failed to get core resources");
+
+	of_node_put(np_pmu);
+	of_node_put(np_cgu);
+	of_node_put(np_ebu);
+
+	if (!request_mem_region(res_pmu.start, resource_size(&res_pmu),
+				res_pmu.name) ||
+		!request_mem_region(res_cgu.start, resource_size(&res_cgu),
+				res_cgu.name) ||
+		!request_mem_region(res_ebu.start, resource_size(&res_ebu),
+				res_ebu.name))
+		pr_err("Failed to request core resources");
+
+	pmu_membase = ioremap(res_pmu.start, resource_size(&res_pmu));
+	ltq_cgu_membase = ioremap(res_cgu.start,
+						resource_size(&res_cgu));
+	ltq_ebu_membase = ioremap(res_ebu.start,
+						resource_size(&res_ebu));
+	if (!pmu_membase || !ltq_cgu_membase || !ltq_ebu_membase)
+		panic("Failed to remap core resources");
+
+	/* make sure to unprotect the memory region where flash is located */
+	ltq_ebu_w32(ltq_ebu_r32(LTQ_EBU_BUSCON0) & ~EBU_WRDIS, LTQ_EBU_BUSCON0);
+
+	/* add our generic xway clocks */
+	clkdev_add_pmu("10000000.fpi", NULL, 0, 0, PMU_FPI);
+	clkdev_add_pmu("1e100a00.gptu", NULL, 1, 0, PMU_GPT);
+	clkdev_add_pmu("1e100bb0.stp", NULL, 1, 0, PMU_STP);
+	clkdev_add_pmu("1e100c00.serial", NULL, 0, 0, PMU_ASC1);
+	clkdev_add_pmu("1e104100.dma", NULL, 1, 0, PMU_DMA);
+	clkdev_add_pmu("1e100800.spi", NULL, 1, 0, PMU_SPI);
+	clkdev_add_pmu("1e105300.ebu", NULL, 0, 0, PMU_EBU);
+	clkdev_add_clkout();
+
+	/* add the soc dependent clocks */
+	if (of_machine_is_compatible("lantiq,vr9")) {
+		ifccr = CGU_IFCCR_VR9;
+		pcicr = CGU_PCICR_VR9;
+	} else {
+		clkdev_add_pmu("1e180000.etop", NULL, 1, 0, PMU_PPE);
+	}
+
+	if (!of_machine_is_compatible("lantiq,ase"))
+		clkdev_add_pci();
+
+	if (of_machine_is_compatible("lantiq,grx390") ||
+	    of_machine_is_compatible("lantiq,ar10")) {
+		clkdev_add_pmu("1e108000.switch", "gphy0", 0, 0, PMU_GPHY0);
+		clkdev_add_pmu("1e108000.switch", "gphy1", 0, 0, PMU_GPHY1);
+		clkdev_add_pmu("1e108000.switch", "gphy2", 0, 0, PMU_GPHY2);
+		clkdev_add_pmu("1f203018.usb2-phy", "phy", 1, 2, PMU_ANALOG_USB0_P);
+		clkdev_add_pmu("1f203034.usb2-phy", "phy", 1, 2, PMU_ANALOG_USB1_P);
+		/* rc 0 */
+		clkdev_add_pmu("1f106800.phy", "phy", 1, 2, PMU_ANALOG_PCIE0_P);
+		clkdev_add_pmu("1d900000.pcie", "msi", 1, 1, PMU1_PCIE_MSI);
+		clkdev_add_pmu("1f106800.phy", "pdi", 1, 1, PMU1_PCIE_PDI);
+		clkdev_add_pmu("1d900000.pcie", "ctl", 1, 1, PMU1_PCIE_CTL);
+		/* rc 1 */
+		clkdev_add_pmu("1f700400.phy", "phy", 1, 2, PMU_ANALOG_PCIE1_P);
+		clkdev_add_pmu("19000000.pcie", "msi", 1, 1, PMU1_PCIE1_MSI);
+		clkdev_add_pmu("1f700400.phy", "pdi", 1, 1, PMU1_PCIE1_PDI);
+		clkdev_add_pmu("19000000.pcie", "ctl", 1, 1, PMU1_PCIE1_CTL);
+	}
+
+	if (of_machine_is_compatible("lantiq,ase")) {
+		if (ltq_cgu_r32(CGU_SYS) & (1 << 5))
+			clkdev_add_static(CLOCK_266M, CLOCK_133M,
+						CLOCK_133M, CLOCK_266M);
+		else
+			clkdev_add_static(CLOCK_133M, CLOCK_133M,
+						CLOCK_133M, CLOCK_133M);
+		clkdev_add_pmu("1e101000.usb", "otg", 1, 0, PMU_USB0);
+		clkdev_add_pmu("1f203018.usb2-phy", "phy", 1, 0, PMU_USB0_P);
+		clkdev_add_pmu("1e180000.etop", "ppe", 1, 0, PMU_PPE);
+		clkdev_add_cgu("1e180000.etop", "ephycgu", CGU_EPHY);
+		clkdev_add_pmu("1e180000.etop", "ephy", 1, 0, PMU_EPHY);
+		clkdev_add_pmu("1e103000.sdio", NULL, 1, 0, PMU_ASE_SDIO);
+		clkdev_add_pmu("1e116000.mei", "dfe", 1, 0, PMU_DFE);
+	} else if (of_machine_is_compatible("lantiq,grx390")) {
+		clkdev_add_static(ltq_grx390_cpu_hz(), ltq_grx390_fpi_hz(),
+				  ltq_grx390_fpi_hz(), ltq_grx390_pp32_hz());
+		clkdev_add_pmu("1e108000.switch", "gphy3", 0, 0, PMU_GPHY3);
+		clkdev_add_pmu("1e101000.usb", "otg", 1, 0, PMU_USB0);
+		clkdev_add_pmu("1e106000.usb", "otg", 1, 0, PMU_USB1);
+		/* rc 2 */
+		clkdev_add_pmu("1f106a00.pcie", "phy", 1, 2, PMU_ANALOG_PCIE2_P);
+		clkdev_add_pmu("1a800000.pcie", "msi", 1, 1, PMU1_PCIE2_MSI);
+		clkdev_add_pmu("1f106a00.pcie", "pdi", 1, 1, PMU1_PCIE2_PDI);
+		clkdev_add_pmu("1a800000.pcie", "ctl", 1, 1, PMU1_PCIE2_CTL);
+		clkdev_add_pmu("1e10b308.eth", NULL, 0, 0, PMU_SWITCH | PMU_PPE_DP);
+		clkdev_add_pmu("1da00000.usif", "NULL", 1, 0, PMU_USIF);
+		clkdev_add_pmu("1e103100.deu", NULL, 1, 0, PMU_DEU);
+	} else if (of_machine_is_compatible("lantiq,ar10")) {
+		clkdev_add_static(ltq_ar10_cpu_hz(), ltq_ar10_fpi_hz(),
+				  ltq_ar10_fpi_hz(), ltq_ar10_pp32_hz());
+		clkdev_add_pmu("1e101000.usb", "otg", 1, 0, PMU_USB0);
+		clkdev_add_pmu("1e106000.usb", "otg", 1, 0, PMU_USB1);
+		clkdev_add_pmu("1e10b308.eth", NULL, 0, 0, PMU_SWITCH |
+			       PMU_PPE_DP | PMU_PPE_TC);
+		clkdev_add_pmu("1da00000.usif", "NULL", 1, 0, PMU_USIF);
+		clkdev_add_pmu("1e103100.deu", NULL, 1, 0, PMU_DEU);
+		clkdev_add_pmu("1e116000.mei", "afe", 1, 2, PMU_ANALOG_DSL_AFE);
+		clkdev_add_pmu("1e116000.mei", "dfe", 1, 0, PMU_DFE);
+	} else if (of_machine_is_compatible("lantiq,vr9")) {
+		clkdev_add_static(ltq_vr9_cpu_hz(), ltq_vr9_fpi_hz(),
+				ltq_vr9_fpi_hz(), ltq_vr9_pp32_hz());
+		clkdev_add_pmu("1f203018.usb2-phy", "phy", 1, 0, PMU_USB0_P);
+		clkdev_add_pmu("1e101000.usb", "otg", 1, 0, PMU_USB0 | PMU_AHBM);
+		clkdev_add_pmu("1f203034.usb2-phy", "phy", 1, 0, PMU_USB1_P);
+		clkdev_add_pmu("1e106000.usb", "otg", 1, 0, PMU_USB1 | PMU_AHBM);
+		clkdev_add_pmu("1f106800.phy", "phy", 1, 1, PMU1_PCIE_PHY);
+		clkdev_add_pmu("1d900000.pcie", "bus", 1, 0, PMU_PCIE_CLK);
+		clkdev_add_pmu("1d900000.pcie", "msi", 1, 1, PMU1_PCIE_MSI);
+		clkdev_add_pmu("1f106800.phy", "pdi", 1, 1, PMU1_PCIE_PDI);
+		clkdev_add_pmu("1d900000.pcie", "ctl", 1, 1, PMU1_PCIE_CTL);
+		clkdev_add_pmu(NULL, "ahb", 1, 0, PMU_AHBM | PMU_AHBS);
+
+		clkdev_add_pmu("1da00000.usif", "NULL", 1, 0, PMU_USIF);
+		clkdev_add_pmu("1e10b308.eth", NULL, 0, 0,
+				PMU_SWITCH | PMU_PPE_DPLUS | PMU_PPE_DPLUM |
+				PMU_PPE_EMA | PMU_PPE_TC | PMU_PPE_SLL01 |
+				PMU_PPE_QSB | PMU_PPE_TOP);
+		clkdev_add_pmu("1e108000.switch", "gphy0", 0, 0, PMU_GPHY);
+		clkdev_add_pmu("1e108000.switch", "gphy1", 0, 0, PMU_GPHY);
+		clkdev_add_pmu("1e103000.sdio", NULL, 1, 0, PMU_SDIO);
+		clkdev_add_pmu("1e103100.deu", NULL, 1, 0, PMU_DEU);
+		clkdev_add_pmu("1e116000.mei", "dfe", 1, 0, PMU_DFE);
+	} else if (of_machine_is_compatible("lantiq,ar9")) {
+		clkdev_add_static(ltq_ar9_cpu_hz(), ltq_ar9_fpi_hz(),
+				ltq_ar9_fpi_hz(), CLOCK_250M);
+		clkdev_add_pmu("1f203018.usb2-phy", "phy", 1, 0, PMU_USB0_P);
+		clkdev_add_pmu("1e101000.usb", "otg", 1, 0, PMU_USB0 | PMU_AHBM);
+		clkdev_add_pmu("1f203034.usb2-phy", "phy", 1, 0, PMU_USB1_P);
+		clkdev_add_pmu("1e106000.usb", "otg", 1, 0, PMU_USB1 | PMU_AHBM);
+		clkdev_add_pmu("1e180000.etop", "switch", 1, 0, PMU_SWITCH);
+		clkdev_add_pmu("1e103000.sdio", NULL, 1, 0, PMU_SDIO);
+		clkdev_add_pmu("1e103100.deu", NULL, 1, 0, PMU_DEU);
+		clkdev_add_pmu("1e116000.mei", "dfe", 1, 0, PMU_DFE);
+		clkdev_add_pmu("1e100400.serial", NULL, 1, 0, PMU_ASC0);
+	} else {
+		clkdev_add_static(ltq_danube_cpu_hz(), ltq_danube_fpi_hz(),
+				ltq_danube_fpi_hz(), ltq_danube_pp32_hz());
+		clkdev_add_pmu("1e101000.usb", "otg", 1, 0, PMU_USB0 | PMU_AHBM);
+		clkdev_add_pmu("1f203018.usb2-phy", "phy", 1, 0, PMU_USB0_P);
+		clkdev_add_pmu("1e103000.sdio", NULL, 1, 0, PMU_SDIO);
+		clkdev_add_pmu("1e103100.deu", NULL, 1, 0, PMU_DEU);
+		clkdev_add_pmu("1e116000.mei", "dfe", 1, 0, PMU_DFE);
+		clkdev_add_pmu("1e100400.serial", NULL, 1, 0, PMU_ASC0);
+	}
+}
diff --git a/arch/mips/lantiq/xway/vmmc.c b/arch/mips/lantiq/xway/vmmc.c
new file mode 100644
index 000000000..2796e87df
--- /dev/null
+++ b/arch/mips/lantiq/xway/vmmc.c
@@ -0,0 +1,70 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ *  Copyright (C) 2012 John Crispin <john@phrozen.org>
+ */
+
+#include <linux/err.h>
+#include <linux/export.h>
+#include <linux/gpio/consumer.h>
+#include <linux/of_platform.h>
+#include <linux/dma-mapping.h>
+
+#include <lantiq_soc.h>
+
+static unsigned int *cp1_base;
+
+unsigned int *ltq_get_cp1_base(void)
+{
+	if (!cp1_base)
+		panic("no cp1 base was set\n");
+
+	return cp1_base;
+}
+EXPORT_SYMBOL(ltq_get_cp1_base);
+
+static int vmmc_probe(struct platform_device *pdev)
+{
+#define CP1_SIZE       (1 << 20)
+	struct gpio_desc *gpio;
+	int gpio_count;
+	dma_addr_t dma;
+	int error;
+
+	cp1_base =
+		(void *) CPHYSADDR(dma_alloc_coherent(&pdev->dev, CP1_SIZE,
+						    &dma, GFP_KERNEL));
+
+	gpio_count = gpiod_count(&pdev->dev, NULL);
+	while (gpio_count > 0) {
+		gpio = devm_gpiod_get_index(&pdev->dev,
+					    NULL, --gpio_count, GPIOD_OUT_HIGH);
+		error = PTR_ERR_OR_ZERO(gpio);
+		if (error) {
+			dev_err(&pdev->dev,
+				"failed to request GPIO idx %d: %d\n",
+				gpio_count, error);
+			continue;
+		}
+
+		gpiod_set_consumer_name(gpio, "vmmc-relay");
+	}
+
+	dev_info(&pdev->dev, "reserved %dMB at 0x%p", CP1_SIZE >> 20, cp1_base);
+
+	return 0;
+}
+
+static const struct of_device_id vmmc_match[] = {
+	{ .compatible = "lantiq,vmmc-xway" },
+	{},
+};
+
+static struct platform_driver vmmc_driver = {
+	.probe = vmmc_probe,
+	.driver = {
+		.name = "lantiq,vmmc",
+		.of_match_table = vmmc_match,
+	},
+};
+builtin_platform_driver(vmmc_driver);
diff --git a/arch/mips/lib/Makefile b/arch/mips/lib/Makefile
new file mode 100644
index 000000000..5d5b993cb
--- /dev/null
+++ b/arch/mips/lib/Makefile
@@ -0,0 +1,18 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Makefile for MIPS-specific library files..
+#
+
+lib-y	+= bitops.o csum_partial.o delay.o memcpy.o memset.o \
+	   mips-atomic.o strncpy_user.o \
+	   strnlen_user.o uncached.o
+
+obj-y			+= iomap_copy.o
+obj-$(CONFIG_PCI)	+= iomap-pci.o
+lib-$(CONFIG_GENERIC_CSUM)	:= $(filter-out csum_partial.o, $(lib-y))
+
+obj-$(CONFIG_CPU_GENERIC_DUMP_TLB) += dump_tlb.o
+obj-$(CONFIG_CPU_R3000)		+= r3k_dump_tlb.o
+
+# libgcc-style stuff needed in the kernel
+obj-y += bswapsi.o bswapdi.o multi3.o
diff --git a/arch/mips/lib/bitops.c b/arch/mips/lib/bitops.c
new file mode 100644
index 000000000..116d0bd8b
--- /dev/null
+++ b/arch/mips/lib/bitops.c
@@ -0,0 +1,148 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (c) 1994-1997, 99, 2000, 06, 07 Ralf Baechle (ralf@linux-mips.org)
+ * Copyright (c) 1999, 2000  Silicon Graphics, Inc.
+ */
+#include <linux/bitops.h>
+#include <linux/bits.h>
+#include <linux/irqflags.h>
+#include <linux/export.h>
+
+
+/**
+ * __mips_set_bit - Atomically set a bit in memory.  This is called by
+ * set_bit() if it cannot find a faster solution.
+ * @nr: the bit to set
+ * @addr: the address to start counting from
+ */
+void __mips_set_bit(unsigned long nr, volatile unsigned long *addr)
+{
+	volatile unsigned long *a = &addr[BIT_WORD(nr)];
+	unsigned int bit = nr % BITS_PER_LONG;
+	unsigned long mask;
+	unsigned long flags;
+
+	mask = 1UL << bit;
+	raw_local_irq_save(flags);
+	*a |= mask;
+	raw_local_irq_restore(flags);
+}
+EXPORT_SYMBOL(__mips_set_bit);
+
+
+/**
+ * __mips_clear_bit - Clears a bit in memory.  This is called by clear_bit() if
+ * it cannot find a faster solution.
+ * @nr: Bit to clear
+ * @addr: Address to start counting from
+ */
+void __mips_clear_bit(unsigned long nr, volatile unsigned long *addr)
+{
+	volatile unsigned long *a = &addr[BIT_WORD(nr)];
+	unsigned int bit = nr % BITS_PER_LONG;
+	unsigned long mask;
+	unsigned long flags;
+
+	mask = 1UL << bit;
+	raw_local_irq_save(flags);
+	*a &= ~mask;
+	raw_local_irq_restore(flags);
+}
+EXPORT_SYMBOL(__mips_clear_bit);
+
+
+/**
+ * __mips_change_bit - Toggle a bit in memory.	This is called by change_bit()
+ * if it cannot find a faster solution.
+ * @nr: Bit to change
+ * @addr: Address to start counting from
+ */
+void __mips_change_bit(unsigned long nr, volatile unsigned long *addr)
+{
+	volatile unsigned long *a = &addr[BIT_WORD(nr)];
+	unsigned int bit = nr % BITS_PER_LONG;
+	unsigned long mask;
+	unsigned long flags;
+
+	mask = 1UL << bit;
+	raw_local_irq_save(flags);
+	*a ^= mask;
+	raw_local_irq_restore(flags);
+}
+EXPORT_SYMBOL(__mips_change_bit);
+
+
+/**
+ * __mips_test_and_set_bit_lock - Set a bit and return its old value.  This is
+ * called by test_and_set_bit_lock() if it cannot find a faster solution.
+ * @nr: Bit to set
+ * @addr: Address to count from
+ */
+int __mips_test_and_set_bit_lock(unsigned long nr,
+				 volatile unsigned long *addr)
+{
+	volatile unsigned long *a = &addr[BIT_WORD(nr)];
+	unsigned int bit = nr % BITS_PER_LONG;
+	unsigned long mask;
+	unsigned long flags;
+	int res;
+
+	mask = 1UL << bit;
+	raw_local_irq_save(flags);
+	res = (mask & *a) != 0;
+	*a |= mask;
+	raw_local_irq_restore(flags);
+	return res;
+}
+EXPORT_SYMBOL(__mips_test_and_set_bit_lock);
+
+
+/**
+ * __mips_test_and_clear_bit - Clear a bit and return its old value.  This is
+ * called by test_and_clear_bit() if it cannot find a faster solution.
+ * @nr: Bit to clear
+ * @addr: Address to count from
+ */
+int __mips_test_and_clear_bit(unsigned long nr, volatile unsigned long *addr)
+{
+	volatile unsigned long *a = &addr[BIT_WORD(nr)];
+	unsigned int bit = nr % BITS_PER_LONG;
+	unsigned long mask;
+	unsigned long flags;
+	int res;
+
+	mask = 1UL << bit;
+	raw_local_irq_save(flags);
+	res = (mask & *a) != 0;
+	*a &= ~mask;
+	raw_local_irq_restore(flags);
+	return res;
+}
+EXPORT_SYMBOL(__mips_test_and_clear_bit);
+
+
+/**
+ * __mips_test_and_change_bit - Change a bit and return its old value.	This is
+ * called by test_and_change_bit() if it cannot find a faster solution.
+ * @nr: Bit to change
+ * @addr: Address to count from
+ */
+int __mips_test_and_change_bit(unsigned long nr, volatile unsigned long *addr)
+{
+	volatile unsigned long *a = &addr[BIT_WORD(nr)];
+	unsigned int bit = nr % BITS_PER_LONG;
+	unsigned long mask;
+	unsigned long flags;
+	int res;
+
+	mask = 1UL << bit;
+	raw_local_irq_save(flags);
+	res = (mask & *a) != 0;
+	*a ^= mask;
+	raw_local_irq_restore(flags);
+	return res;
+}
+EXPORT_SYMBOL(__mips_test_and_change_bit);
diff --git a/arch/mips/lib/bswapdi.c b/arch/mips/lib/bswapdi.c
new file mode 100644
index 000000000..88242dc7d
--- /dev/null
+++ b/arch/mips/lib/bswapdi.c
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/export.h>
+#include <linux/compiler.h>
+#include <uapi/linux/swab.h>
+
+/* To silence -Wmissing-prototypes. */
+unsigned long long __bswapdi2(unsigned long long u);
+
+unsigned long long notrace __bswapdi2(unsigned long long u)
+{
+	return ___constant_swab64(u);
+}
+EXPORT_SYMBOL(__bswapdi2);
diff --git a/arch/mips/lib/bswapsi.c b/arch/mips/lib/bswapsi.c
new file mode 100644
index 000000000..2ed655497
--- /dev/null
+++ b/arch/mips/lib/bswapsi.c
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/export.h>
+#include <linux/compiler.h>
+#include <uapi/linux/swab.h>
+
+/* To silence -Wmissing-prototypes. */
+unsigned int __bswapsi2(unsigned int u);
+
+unsigned int notrace __bswapsi2(unsigned int u)
+{
+	return ___constant_swab32(u);
+}
+EXPORT_SYMBOL(__bswapsi2);
diff --git a/arch/mips/lib/csum_partial.S b/arch/mips/lib/csum_partial.S
new file mode 100644
index 000000000..7767137c3
--- /dev/null
+++ b/arch/mips/lib/csum_partial.S
@@ -0,0 +1,754 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Quick'n'dirty IP checksum ...
+ *
+ * Copyright (C) 1998, 1999 Ralf Baechle
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ * Copyright (C) 2007  Maciej W. Rozycki
+ * Copyright (C) 2014 Imagination Technologies Ltd.
+ */
+#include <linux/errno.h>
+#include <asm/asm.h>
+#include <asm/asm-offsets.h>
+#include <asm/export.h>
+#include <asm/regdef.h>
+
+#ifdef CONFIG_64BIT
+/*
+ * As we are sharing code base with the mips32 tree (which use the o32 ABI
+ * register definitions). We need to redefine the register definitions from
+ * the n64 ABI register naming to the o32 ABI register naming.
+ */
+#undef t0
+#undef t1
+#undef t2
+#undef t3
+#define t0	$8
+#define t1	$9
+#define t2	$10
+#define t3	$11
+#define t4	$12
+#define t5	$13
+#define t6	$14
+#define t7	$15
+
+#define USE_DOUBLE
+#endif
+
+#ifdef USE_DOUBLE
+
+#define LOAD   ld
+#define LOAD32 lwu
+#define ADD    daddu
+#define NBYTES 8
+
+#else
+
+#define LOAD   lw
+#define LOAD32 lw
+#define ADD    addu
+#define NBYTES 4
+
+#endif /* USE_DOUBLE */
+
+#define UNIT(unit)  ((unit)*NBYTES)
+
+#define ADDC(sum,reg)						\
+	.set	push;						\
+	.set	noat;						\
+	ADD	sum, reg;					\
+	sltu	v1, sum, reg;					\
+	ADD	sum, v1;					\
+	.set	pop
+
+#define ADDC32(sum,reg)						\
+	.set	push;						\
+	.set	noat;						\
+	addu	sum, reg;					\
+	sltu	v1, sum, reg;					\
+	addu	sum, v1;					\
+	.set	pop
+
+#define CSUM_BIGCHUNK1(src, offset, sum, _t0, _t1, _t2, _t3)	\
+	LOAD	_t0, (offset + UNIT(0))(src);			\
+	LOAD	_t1, (offset + UNIT(1))(src);			\
+	LOAD	_t2, (offset + UNIT(2))(src);			\
+	LOAD	_t3, (offset + UNIT(3))(src);			\
+	ADDC(_t0, _t1);						\
+	ADDC(_t2, _t3);						\
+	ADDC(sum, _t0);						\
+	ADDC(sum, _t2)
+
+#ifdef USE_DOUBLE
+#define CSUM_BIGCHUNK(src, offset, sum, _t0, _t1, _t2, _t3)	\
+	CSUM_BIGCHUNK1(src, offset, sum, _t0, _t1, _t2, _t3)
+#else
+#define CSUM_BIGCHUNK(src, offset, sum, _t0, _t1, _t2, _t3)	\
+	CSUM_BIGCHUNK1(src, offset, sum, _t0, _t1, _t2, _t3);	\
+	CSUM_BIGCHUNK1(src, offset + 0x10, sum, _t0, _t1, _t2, _t3)
+#endif
+
+/*
+ * a0: source address
+ * a1: length of the area to checksum
+ * a2: partial checksum
+ */
+
+#define src a0
+#define sum v0
+
+	.text
+	.set	noreorder
+	.align	5
+LEAF(csum_partial)
+EXPORT_SYMBOL(csum_partial)
+	move	sum, zero
+	move	t7, zero
+
+	sltiu	t8, a1, 0x8
+	bnez	t8, .Lsmall_csumcpy		/* < 8 bytes to copy */
+	 move	t2, a1
+
+	andi	t7, src, 0x1			/* odd buffer? */
+
+.Lhword_align:
+	beqz	t7, .Lword_align
+	 andi	t8, src, 0x2
+
+	lbu	t0, (src)
+	LONG_SUBU	a1, a1, 0x1
+#ifdef __MIPSEL__
+	sll	t0, t0, 8
+#endif
+	ADDC(sum, t0)
+	PTR_ADDU	src, src, 0x1
+	andi	t8, src, 0x2
+
+.Lword_align:
+	beqz	t8, .Ldword_align
+	 sltiu	t8, a1, 56
+
+	lhu	t0, (src)
+	LONG_SUBU	a1, a1, 0x2
+	ADDC(sum, t0)
+	sltiu	t8, a1, 56
+	PTR_ADDU	src, src, 0x2
+
+.Ldword_align:
+	bnez	t8, .Ldo_end_words
+	 move	t8, a1
+
+	andi	t8, src, 0x4
+	beqz	t8, .Lqword_align
+	 andi	t8, src, 0x8
+
+	LOAD32	t0, 0x00(src)
+	LONG_SUBU	a1, a1, 0x4
+	ADDC(sum, t0)
+	PTR_ADDU	src, src, 0x4
+	andi	t8, src, 0x8
+
+.Lqword_align:
+	beqz	t8, .Loword_align
+	 andi	t8, src, 0x10
+
+#ifdef USE_DOUBLE
+	ld	t0, 0x00(src)
+	LONG_SUBU	a1, a1, 0x8
+	ADDC(sum, t0)
+#else
+	lw	t0, 0x00(src)
+	lw	t1, 0x04(src)
+	LONG_SUBU	a1, a1, 0x8
+	ADDC(sum, t0)
+	ADDC(sum, t1)
+#endif
+	PTR_ADDU	src, src, 0x8
+	andi	t8, src, 0x10
+
+.Loword_align:
+	beqz	t8, .Lbegin_movement
+	 LONG_SRL	t8, a1, 0x7
+
+#ifdef USE_DOUBLE
+	ld	t0, 0x00(src)
+	ld	t1, 0x08(src)
+	ADDC(sum, t0)
+	ADDC(sum, t1)
+#else
+	CSUM_BIGCHUNK1(src, 0x00, sum, t0, t1, t3, t4)
+#endif
+	LONG_SUBU	a1, a1, 0x10
+	PTR_ADDU	src, src, 0x10
+	LONG_SRL	t8, a1, 0x7
+
+.Lbegin_movement:
+	beqz	t8, 1f
+	 andi	t2, a1, 0x40
+
+.Lmove_128bytes:
+	CSUM_BIGCHUNK(src, 0x00, sum, t0, t1, t3, t4)
+	CSUM_BIGCHUNK(src, 0x20, sum, t0, t1, t3, t4)
+	CSUM_BIGCHUNK(src, 0x40, sum, t0, t1, t3, t4)
+	CSUM_BIGCHUNK(src, 0x60, sum, t0, t1, t3, t4)
+	LONG_SUBU	t8, t8, 0x01
+	.set	reorder				/* DADDI_WAR */
+	PTR_ADDU	src, src, 0x80
+	bnez	t8, .Lmove_128bytes
+	.set	noreorder
+
+1:
+	beqz	t2, 1f
+	 andi	t2, a1, 0x20
+
+.Lmove_64bytes:
+	CSUM_BIGCHUNK(src, 0x00, sum, t0, t1, t3, t4)
+	CSUM_BIGCHUNK(src, 0x20, sum, t0, t1, t3, t4)
+	PTR_ADDU	src, src, 0x40
+
+1:
+	beqz	t2, .Ldo_end_words
+	 andi	t8, a1, 0x1c
+
+.Lmove_32bytes:
+	CSUM_BIGCHUNK(src, 0x00, sum, t0, t1, t3, t4)
+	andi	t8, a1, 0x1c
+	PTR_ADDU	src, src, 0x20
+
+.Ldo_end_words:
+	beqz	t8, .Lsmall_csumcpy
+	 andi	t2, a1, 0x3
+	LONG_SRL	t8, t8, 0x2
+
+.Lend_words:
+	LOAD32	t0, (src)
+	LONG_SUBU	t8, t8, 0x1
+	ADDC(sum, t0)
+	.set	reorder				/* DADDI_WAR */
+	PTR_ADDU	src, src, 0x4
+	bnez	t8, .Lend_words
+	.set	noreorder
+
+/* unknown src alignment and < 8 bytes to go  */
+.Lsmall_csumcpy:
+	move	a1, t2
+
+	andi	t0, a1, 4
+	beqz	t0, 1f
+	 andi	t0, a1, 2
+
+	/* Still a full word to go  */
+	ulw	t1, (src)
+	PTR_ADDIU	src, 4
+#ifdef USE_DOUBLE
+	dsll	t1, t1, 32			/* clear lower 32bit */
+#endif
+	ADDC(sum, t1)
+
+1:	move	t1, zero
+	beqz	t0, 1f
+	 andi	t0, a1, 1
+
+	/* Still a halfword to go  */
+	ulhu	t1, (src)
+	PTR_ADDIU	src, 2
+
+1:	beqz	t0, 1f
+	 sll	t1, t1, 16
+
+	lbu	t2, (src)
+	 nop
+
+#ifdef __MIPSEB__
+	sll	t2, t2, 8
+#endif
+	or	t1, t2
+
+1:	ADDC(sum, t1)
+
+	/* fold checksum */
+#ifdef USE_DOUBLE
+	dsll32	v1, sum, 0
+	daddu	sum, v1
+	sltu	v1, sum, v1
+	dsra32	sum, sum, 0
+	addu	sum, v1
+#endif
+
+	/* odd buffer alignment? */
+#if defined(CONFIG_CPU_MIPSR2) || defined(CONFIG_CPU_MIPSR5) || \
+    defined(CONFIG_CPU_LOONGSON64)
+	.set	push
+	.set	arch=mips32r2
+	wsbh	v1, sum
+	movn	sum, v1, t7
+	.set	pop
+#else
+	beqz	t7, 1f			/* odd buffer alignment? */
+	 lui	v1, 0x00ff
+	addu	v1, 0x00ff
+	and	t0, sum, v1
+	sll	t0, t0, 8
+	srl	sum, sum, 8
+	and	sum, sum, v1
+	or	sum, sum, t0
+1:
+#endif
+	.set	reorder
+	/* Add the passed partial csum.	 */
+	ADDC32(sum, a2)
+	jr	ra
+	.set	noreorder
+	END(csum_partial)
+
+
+/*
+ * checksum and copy routines based on memcpy.S
+ *
+ *	csum_partial_copy_nocheck(src, dst, len)
+ *	__csum_partial_copy_kernel(src, dst, len)
+ *
+ * See "Spec" in memcpy.S for details.	Unlike __copy_user, all
+ * function in this file use the standard calling convention.
+ */
+
+#define src a0
+#define dst a1
+#define len a2
+#define sum v0
+#define odd t8
+
+/*
+ * All exception handlers simply return 0.
+ */
+
+/* Instruction type */
+#define LD_INSN 1
+#define ST_INSN 2
+#define LEGACY_MODE 1
+#define EVA_MODE    2
+#define USEROP   1
+#define KERNELOP 2
+
+/*
+ * Wrapper to add an entry in the exception table
+ * in case the insn causes a memory exception.
+ * Arguments:
+ * insn    : Load/store instruction
+ * type    : Instruction type
+ * reg     : Register
+ * addr    : Address
+ * handler : Exception handler
+ */
+#define EXC(insn, type, reg, addr)		\
+	.if \mode == LEGACY_MODE;		\
+9:		insn reg, addr;			\
+		.section __ex_table,"a";	\
+		PTR_WD	9b, .L_exc;		\
+		.previous;			\
+	/* This is enabled in EVA mode */	\
+	.else;					\
+		/* If loading from user or storing to user */	\
+		.if ((\from == USEROP) && (type == LD_INSN)) || \
+		    ((\to == USEROP) && (type == ST_INSN));	\
+9:			__BUILD_EVA_INSN(insn##e, reg, addr);	\
+			.section __ex_table,"a";		\
+			PTR_WD	9b, .L_exc;			\
+			.previous;				\
+		.else;						\
+			/* EVA without exception */		\
+			insn reg, addr;				\
+		.endif;						\
+	.endif
+
+#undef LOAD
+
+#ifdef USE_DOUBLE
+
+#define LOADK	ld /* No exception */
+#define LOAD(reg, addr)		EXC(ld, LD_INSN, reg, addr)
+#define LOADBU(reg, addr)	EXC(lbu, LD_INSN, reg, addr)
+#define LOADL(reg, addr)	EXC(ldl, LD_INSN, reg, addr)
+#define LOADR(reg, addr)	EXC(ldr, LD_INSN, reg, addr)
+#define STOREB(reg, addr)	EXC(sb, ST_INSN, reg, addr)
+#define STOREL(reg, addr)	EXC(sdl, ST_INSN, reg, addr)
+#define STORER(reg, addr)	EXC(sdr, ST_INSN, reg, addr)
+#define STORE(reg, addr)	EXC(sd, ST_INSN, reg, addr)
+#define ADD    daddu
+#define SUB    dsubu
+#define SRL    dsrl
+#define SLL    dsll
+#define SLLV   dsllv
+#define SRLV   dsrlv
+#define NBYTES 8
+#define LOG_NBYTES 3
+
+#else
+
+#define LOADK	lw /* No exception */
+#define LOAD(reg, addr)		EXC(lw, LD_INSN, reg, addr)
+#define LOADBU(reg, addr)	EXC(lbu, LD_INSN, reg, addr)
+#define LOADL(reg, addr)	EXC(lwl, LD_INSN, reg, addr)
+#define LOADR(reg, addr)	EXC(lwr, LD_INSN, reg, addr)
+#define STOREB(reg, addr)	EXC(sb, ST_INSN, reg, addr)
+#define STOREL(reg, addr)	EXC(swl, ST_INSN, reg, addr)
+#define STORER(reg, addr)	EXC(swr, ST_INSN, reg, addr)
+#define STORE(reg, addr)	EXC(sw, ST_INSN, reg, addr)
+#define ADD    addu
+#define SUB    subu
+#define SRL    srl
+#define SLL    sll
+#define SLLV   sllv
+#define SRLV   srlv
+#define NBYTES 4
+#define LOG_NBYTES 2
+
+#endif /* USE_DOUBLE */
+
+#ifdef CONFIG_CPU_LITTLE_ENDIAN
+#define LDFIRST LOADR
+#define LDREST	LOADL
+#define STFIRST STORER
+#define STREST	STOREL
+#define SHIFT_DISCARD SLLV
+#define SHIFT_DISCARD_REVERT SRLV
+#else
+#define LDFIRST LOADL
+#define LDREST	LOADR
+#define STFIRST STOREL
+#define STREST	STORER
+#define SHIFT_DISCARD SRLV
+#define SHIFT_DISCARD_REVERT SLLV
+#endif
+
+#define FIRST(unit) ((unit)*NBYTES)
+#define REST(unit)  (FIRST(unit)+NBYTES-1)
+
+#define ADDRMASK (NBYTES-1)
+
+#ifndef CONFIG_CPU_DADDI_WORKAROUNDS
+	.set	noat
+#else
+	.set	at=v1
+#endif
+
+	.macro __BUILD_CSUM_PARTIAL_COPY_USER mode, from, to
+
+	li	sum, -1
+	move	odd, zero
+	/*
+	 * Note: dst & src may be unaligned, len may be 0
+	 * Temps
+	 */
+	/*
+	 * The "issue break"s below are very approximate.
+	 * Issue delays for dcache fills will perturb the schedule, as will
+	 * load queue full replay traps, etc.
+	 *
+	 * If len < NBYTES use byte operations.
+	 */
+	sltu	t2, len, NBYTES
+	and	t1, dst, ADDRMASK
+	bnez	t2, .Lcopy_bytes_checklen\@
+	 and	t0, src, ADDRMASK
+	andi	odd, dst, 0x1			/* odd buffer? */
+	bnez	t1, .Ldst_unaligned\@
+	 nop
+	bnez	t0, .Lsrc_unaligned_dst_aligned\@
+	/*
+	 * use delay slot for fall-through
+	 * src and dst are aligned; need to compute rem
+	 */
+.Lboth_aligned\@:
+	 SRL	t0, len, LOG_NBYTES+3	 # +3 for 8 units/iter
+	beqz	t0, .Lcleanup_both_aligned\@ # len < 8*NBYTES
+	 nop
+	SUB	len, 8*NBYTES		# subtract here for bgez loop
+	.align	4
+1:
+	LOAD(t0, UNIT(0)(src))
+	LOAD(t1, UNIT(1)(src))
+	LOAD(t2, UNIT(2)(src))
+	LOAD(t3, UNIT(3)(src))
+	LOAD(t4, UNIT(4)(src))
+	LOAD(t5, UNIT(5)(src))
+	LOAD(t6, UNIT(6)(src))
+	LOAD(t7, UNIT(7)(src))
+	SUB	len, len, 8*NBYTES
+	ADD	src, src, 8*NBYTES
+	STORE(t0, UNIT(0)(dst))
+	ADDC(t0, t1)
+	STORE(t1, UNIT(1)(dst))
+	ADDC(sum, t0)
+	STORE(t2, UNIT(2)(dst))
+	ADDC(t2, t3)
+	STORE(t3, UNIT(3)(dst))
+	ADDC(sum, t2)
+	STORE(t4, UNIT(4)(dst))
+	ADDC(t4, t5)
+	STORE(t5, UNIT(5)(dst))
+	ADDC(sum, t4)
+	STORE(t6, UNIT(6)(dst))
+	ADDC(t6, t7)
+	STORE(t7, UNIT(7)(dst))
+	ADDC(sum, t6)
+	.set	reorder				/* DADDI_WAR */
+	ADD	dst, dst, 8*NBYTES
+	bgez	len, 1b
+	.set	noreorder
+	ADD	len, 8*NBYTES		# revert len (see above)
+
+	/*
+	 * len == the number of bytes left to copy < 8*NBYTES
+	 */
+.Lcleanup_both_aligned\@:
+#define rem t7
+	beqz	len, .Ldone\@
+	 sltu	t0, len, 4*NBYTES
+	bnez	t0, .Lless_than_4units\@
+	 and	rem, len, (NBYTES-1)	# rem = len % NBYTES
+	/*
+	 * len >= 4*NBYTES
+	 */
+	LOAD(t0, UNIT(0)(src))
+	LOAD(t1, UNIT(1)(src))
+	LOAD(t2, UNIT(2)(src))
+	LOAD(t3, UNIT(3)(src))
+	SUB	len, len, 4*NBYTES
+	ADD	src, src, 4*NBYTES
+	STORE(t0, UNIT(0)(dst))
+	ADDC(t0, t1)
+	STORE(t1, UNIT(1)(dst))
+	ADDC(sum, t0)
+	STORE(t2, UNIT(2)(dst))
+	ADDC(t2, t3)
+	STORE(t3, UNIT(3)(dst))
+	ADDC(sum, t2)
+	.set	reorder				/* DADDI_WAR */
+	ADD	dst, dst, 4*NBYTES
+	beqz	len, .Ldone\@
+	.set	noreorder
+.Lless_than_4units\@:
+	/*
+	 * rem = len % NBYTES
+	 */
+	beq	rem, len, .Lcopy_bytes\@
+	 nop
+1:
+	LOAD(t0, 0(src))
+	ADD	src, src, NBYTES
+	SUB	len, len, NBYTES
+	STORE(t0, 0(dst))
+	ADDC(sum, t0)
+	.set	reorder				/* DADDI_WAR */
+	ADD	dst, dst, NBYTES
+	bne	rem, len, 1b
+	.set	noreorder
+
+	/*
+	 * src and dst are aligned, need to copy rem bytes (rem < NBYTES)
+	 * A loop would do only a byte at a time with possible branch
+	 * mispredicts.	 Can't do an explicit LOAD dst,mask,or,STORE
+	 * because can't assume read-access to dst.  Instead, use
+	 * STREST dst, which doesn't require read access to dst.
+	 *
+	 * This code should perform better than a simple loop on modern,
+	 * wide-issue mips processors because the code has fewer branches and
+	 * more instruction-level parallelism.
+	 */
+#define bits t2
+	beqz	len, .Ldone\@
+	 ADD	t1, dst, len	# t1 is just past last byte of dst
+	li	bits, 8*NBYTES
+	SLL	rem, len, 3	# rem = number of bits to keep
+	LOAD(t0, 0(src))
+	SUB	bits, bits, rem # bits = number of bits to discard
+	SHIFT_DISCARD t0, t0, bits
+	STREST(t0, -1(t1))
+	SHIFT_DISCARD_REVERT t0, t0, bits
+	.set reorder
+	ADDC(sum, t0)
+	b	.Ldone\@
+	.set noreorder
+.Ldst_unaligned\@:
+	/*
+	 * dst is unaligned
+	 * t0 = src & ADDRMASK
+	 * t1 = dst & ADDRMASK; T1 > 0
+	 * len >= NBYTES
+	 *
+	 * Copy enough bytes to align dst
+	 * Set match = (src and dst have same alignment)
+	 */
+#define match rem
+	LDFIRST(t3, FIRST(0)(src))
+	ADD	t2, zero, NBYTES
+	LDREST(t3, REST(0)(src))
+	SUB	t2, t2, t1	# t2 = number of bytes copied
+	xor	match, t0, t1
+	STFIRST(t3, FIRST(0)(dst))
+	SLL	t4, t1, 3		# t4 = number of bits to discard
+	SHIFT_DISCARD t3, t3, t4
+	/* no SHIFT_DISCARD_REVERT to handle odd buffer properly */
+	ADDC(sum, t3)
+	beq	len, t2, .Ldone\@
+	 SUB	len, len, t2
+	ADD	dst, dst, t2
+	beqz	match, .Lboth_aligned\@
+	 ADD	src, src, t2
+
+.Lsrc_unaligned_dst_aligned\@:
+	SRL	t0, len, LOG_NBYTES+2	 # +2 for 4 units/iter
+	beqz	t0, .Lcleanup_src_unaligned\@
+	 and	rem, len, (4*NBYTES-1)	 # rem = len % 4*NBYTES
+1:
+/*
+ * Avoid consecutive LD*'s to the same register since some mips
+ * implementations can't issue them in the same cycle.
+ * It's OK to load FIRST(N+1) before REST(N) because the two addresses
+ * are to the same unit (unless src is aligned, but it's not).
+ */
+	LDFIRST(t0, FIRST(0)(src))
+	LDFIRST(t1, FIRST(1)(src))
+	SUB	len, len, 4*NBYTES
+	LDREST(t0, REST(0)(src))
+	LDREST(t1, REST(1)(src))
+	LDFIRST(t2, FIRST(2)(src))
+	LDFIRST(t3, FIRST(3)(src))
+	LDREST(t2, REST(2)(src))
+	LDREST(t3, REST(3)(src))
+	ADD	src, src, 4*NBYTES
+#ifdef CONFIG_CPU_SB1
+	nop				# improves slotting
+#endif
+	STORE(t0, UNIT(0)(dst))
+	ADDC(t0, t1)
+	STORE(t1, UNIT(1)(dst))
+	ADDC(sum, t0)
+	STORE(t2, UNIT(2)(dst))
+	ADDC(t2, t3)
+	STORE(t3, UNIT(3)(dst))
+	ADDC(sum, t2)
+	.set	reorder				/* DADDI_WAR */
+	ADD	dst, dst, 4*NBYTES
+	bne	len, rem, 1b
+	.set	noreorder
+
+.Lcleanup_src_unaligned\@:
+	beqz	len, .Ldone\@
+	 and	rem, len, NBYTES-1  # rem = len % NBYTES
+	beq	rem, len, .Lcopy_bytes\@
+	 nop
+1:
+	LDFIRST(t0, FIRST(0)(src))
+	LDREST(t0, REST(0)(src))
+	ADD	src, src, NBYTES
+	SUB	len, len, NBYTES
+	STORE(t0, 0(dst))
+	ADDC(sum, t0)
+	.set	reorder				/* DADDI_WAR */
+	ADD	dst, dst, NBYTES
+	bne	len, rem, 1b
+	.set	noreorder
+
+.Lcopy_bytes_checklen\@:
+	beqz	len, .Ldone\@
+	 nop
+.Lcopy_bytes\@:
+	/* 0 < len < NBYTES  */
+#ifdef CONFIG_CPU_LITTLE_ENDIAN
+#define SHIFT_START 0
+#define SHIFT_INC 8
+#else
+#define SHIFT_START 8*(NBYTES-1)
+#define SHIFT_INC -8
+#endif
+	move	t2, zero	# partial word
+	li	t3, SHIFT_START # shift
+#define COPY_BYTE(N)			\
+	LOADBU(t0, N(src));		\
+	SUB	len, len, 1;		\
+	STOREB(t0, N(dst));		\
+	SLLV	t0, t0, t3;		\
+	addu	t3, SHIFT_INC;		\
+	beqz	len, .Lcopy_bytes_done\@; \
+	 or	t2, t0
+
+	COPY_BYTE(0)
+	COPY_BYTE(1)
+#ifdef USE_DOUBLE
+	COPY_BYTE(2)
+	COPY_BYTE(3)
+	COPY_BYTE(4)
+	COPY_BYTE(5)
+#endif
+	LOADBU(t0, NBYTES-2(src))
+	SUB	len, len, 1
+	STOREB(t0, NBYTES-2(dst))
+	SLLV	t0, t0, t3
+	or	t2, t0
+.Lcopy_bytes_done\@:
+	ADDC(sum, t2)
+.Ldone\@:
+	/* fold checksum */
+	.set	push
+	.set	noat
+#ifdef USE_DOUBLE
+	dsll32	v1, sum, 0
+	daddu	sum, v1
+	sltu	v1, sum, v1
+	dsra32	sum, sum, 0
+	addu	sum, v1
+#endif
+
+#if defined(CONFIG_CPU_MIPSR2) || defined(CONFIG_CPU_MIPSR5) || \
+    defined(CONFIG_CPU_LOONGSON64)
+	.set	push
+	.set	arch=mips32r2
+	wsbh	v1, sum
+	movn	sum, v1, odd
+	.set	pop
+#else
+	beqz	odd, 1f			/* odd buffer alignment? */
+	 lui	v1, 0x00ff
+	addu	v1, 0x00ff
+	and	t0, sum, v1
+	sll	t0, t0, 8
+	srl	sum, sum, 8
+	and	sum, sum, v1
+	or	sum, sum, t0
+1:
+#endif
+	.set	pop
+	.set reorder
+	jr	ra
+	.set noreorder
+	.endm
+
+	.set noreorder
+.L_exc:
+	jr	ra
+	 li	v0, 0
+
+FEXPORT(__csum_partial_copy_nocheck)
+EXPORT_SYMBOL(__csum_partial_copy_nocheck)
+#ifndef CONFIG_EVA
+FEXPORT(__csum_partial_copy_to_user)
+EXPORT_SYMBOL(__csum_partial_copy_to_user)
+FEXPORT(__csum_partial_copy_from_user)
+EXPORT_SYMBOL(__csum_partial_copy_from_user)
+#endif
+__BUILD_CSUM_PARTIAL_COPY_USER LEGACY_MODE USEROP USEROP
+
+#ifdef CONFIG_EVA
+LEAF(__csum_partial_copy_to_user)
+__BUILD_CSUM_PARTIAL_COPY_USER EVA_MODE KERNELOP USEROP
+END(__csum_partial_copy_to_user)
+
+LEAF(__csum_partial_copy_from_user)
+__BUILD_CSUM_PARTIAL_COPY_USER EVA_MODE USEROP KERNELOP
+END(__csum_partial_copy_from_user)
+#endif
diff --git a/arch/mips/lib/delay.c b/arch/mips/lib/delay.c
new file mode 100644
index 000000000..ccdb1fc1e
--- /dev/null
+++ b/arch/mips/lib/delay.c
@@ -0,0 +1,68 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994 by Waldorf Electronics
+ * Copyright (C) 1995 - 2000, 01, 03 by Ralf Baechle
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ * Copyright (C) 2007, 2014 Maciej W. Rozycki
+ */
+#include <linux/delay.h>
+#include <linux/export.h>
+#include <linux/param.h>
+#include <linux/smp.h>
+#include <linux/stringify.h>
+
+#include <asm/asm.h>
+#include <asm/compiler.h>
+
+#ifndef CONFIG_CPU_DADDI_WORKAROUNDS
+#define GCC_DADDI_IMM_ASM() "I"
+#else
+#define GCC_DADDI_IMM_ASM() "r"
+#endif
+
+#ifndef CONFIG_HAVE_PLAT_DELAY
+
+void __delay(unsigned long loops)
+{
+	__asm__ __volatile__ (
+	"	.set	noreorder				\n"
+	"	.align	3					\n"
+	"1:	bnez	%0, 1b					\n"
+	"	 " __stringify(LONG_SUBU) "	%0, %1		\n"
+	"	.set	reorder					\n"
+	: "=r" (loops)
+	: GCC_DADDI_IMM_ASM() (1), "0" (loops));
+}
+EXPORT_SYMBOL(__delay);
+
+/*
+ * Division by multiplication: you don't have to worry about
+ * loss of precision.
+ *
+ * Use only for very small delays ( < 1 msec).	Should probably use a
+ * lookup table, really, as the multiplications take much too long with
+ * short delays.  This is a "reasonable" implementation, though (and the
+ * first constant multiplications gets optimized away if the delay is
+ * a constant)
+ */
+
+void __udelay(unsigned long us)
+{
+	unsigned int lpj = raw_current_cpu_data.udelay_val;
+
+	__delay((us * 0x000010c7ull * HZ * lpj) >> 32);
+}
+EXPORT_SYMBOL(__udelay);
+
+void __ndelay(unsigned long ns)
+{
+	unsigned int lpj = raw_current_cpu_data.udelay_val;
+
+	__delay((ns * 0x00000005ull * HZ * lpj) >> 32);
+}
+EXPORT_SYMBOL(__ndelay);
+
+#endif
diff --git a/arch/mips/lib/dump_tlb.c b/arch/mips/lib/dump_tlb.c
new file mode 100644
index 000000000..8ce97b874
--- /dev/null
+++ b/arch/mips/lib/dump_tlb.c
@@ -0,0 +1,191 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Dump R4x00 TLB for debugging purposes.
+ *
+ * Copyright (C) 1994, 1995 by Waldorf Electronics, written by Ralf Baechle.
+ * Copyright (C) 1999 by Silicon Graphics, Inc.
+ */
+#include <linux/kernel.h>
+#include <linux/mm.h>
+
+#include <asm/hazards.h>
+#include <asm/mipsregs.h>
+#include <asm/mmu_context.h>
+#include <asm/page.h>
+#include <asm/tlbdebug.h>
+
+void dump_tlb_regs(void)
+{
+	const int field = 2 * sizeof(unsigned long);
+
+	pr_info("Index    : %0x\n", read_c0_index());
+	pr_info("PageMask : %0x\n", read_c0_pagemask());
+	if (cpu_has_guestid)
+		pr_info("GuestCtl1: %0x\n", read_c0_guestctl1());
+	pr_info("EntryHi  : %0*lx\n", field, read_c0_entryhi());
+	pr_info("EntryLo0 : %0*lx\n", field, read_c0_entrylo0());
+	pr_info("EntryLo1 : %0*lx\n", field, read_c0_entrylo1());
+	pr_info("Wired    : %0x\n", read_c0_wired());
+	switch (current_cpu_type()) {
+	case CPU_R10000:
+	case CPU_R12000:
+	case CPU_R14000:
+	case CPU_R16000:
+		pr_info("FrameMask: %0x\n", read_c0_framemask());
+		break;
+	}
+	if (cpu_has_small_pages || cpu_has_rixi || cpu_has_xpa)
+		pr_info("PageGrain: %0x\n", read_c0_pagegrain());
+	if (cpu_has_htw) {
+		pr_info("PWField  : %0*lx\n", field, read_c0_pwfield());
+		pr_info("PWSize   : %0*lx\n", field, read_c0_pwsize());
+		pr_info("PWCtl    : %0x\n", read_c0_pwctl());
+	}
+}
+
+static inline const char *msk2str(unsigned int mask)
+{
+	switch (mask) {
+	case PM_4K:	return "4kb";
+	case PM_16K:	return "16kb";
+	case PM_64K:	return "64kb";
+	case PM_256K:	return "256kb";
+#ifdef CONFIG_CPU_CAVIUM_OCTEON
+	case PM_8K:	return "8kb";
+	case PM_32K:	return "32kb";
+	case PM_128K:	return "128kb";
+	case PM_512K:	return "512kb";
+	case PM_2M:	return "2Mb";
+	case PM_8M:	return "8Mb";
+	case PM_32M:	return "32Mb";
+#endif
+	}
+	return "";
+}
+
+static void dump_tlb(int first, int last)
+{
+	unsigned long s_entryhi, entryhi, asid, mmid;
+	unsigned long long entrylo0, entrylo1, pa;
+	unsigned int s_index, s_pagemask, s_guestctl1 = 0;
+	unsigned int pagemask, guestctl1 = 0, c0, c1, i;
+	unsigned long asidmask = cpu_asid_mask(&current_cpu_data);
+	int asidwidth = DIV_ROUND_UP(ilog2(asidmask) + 1, 4);
+	unsigned long s_mmid;
+#ifdef CONFIG_32BIT
+	bool xpa = cpu_has_xpa && (read_c0_pagegrain() & PG_ELPA);
+	int pwidth = xpa ? 11 : 8;
+	int vwidth = 8;
+#else
+	bool xpa = false;
+	int pwidth = 11;
+	int vwidth = 11;
+#endif
+
+	s_pagemask = read_c0_pagemask();
+	s_entryhi = read_c0_entryhi();
+	s_index = read_c0_index();
+
+	if (cpu_has_mmid)
+		asid = s_mmid = read_c0_memorymapid();
+	else
+		asid = s_entryhi & asidmask;
+
+	if (cpu_has_guestid)
+		s_guestctl1 = read_c0_guestctl1();
+
+	for (i = first; i <= last; i++) {
+		write_c0_index(i);
+		mtc0_tlbr_hazard();
+		tlb_read();
+		tlb_read_hazard();
+		pagemask = read_c0_pagemask();
+		entryhi	 = read_c0_entryhi();
+		entrylo0 = read_c0_entrylo0();
+		entrylo1 = read_c0_entrylo1();
+
+		if (cpu_has_mmid)
+			mmid = read_c0_memorymapid();
+		else
+			mmid = entryhi & asidmask;
+
+		if (cpu_has_guestid)
+			guestctl1 = read_c0_guestctl1();
+
+		/* EHINV bit marks entire entry as invalid */
+		if (cpu_has_tlbinv && entryhi & MIPS_ENTRYHI_EHINV)
+			continue;
+		/*
+		 * Prior to tlbinv, unused entries have a virtual address of
+		 * CKSEG0.
+		 */
+		if ((entryhi & ~0x1ffffUL) == CKSEG0)
+			continue;
+		/*
+		 * ASID takes effect in absence of G (global) bit.
+		 * We check both G bits, even though architecturally they should
+		 * match one another, because some revisions of the SB1 core may
+		 * leave only a single G bit set after a machine check exception
+		 * due to duplicate TLB entry.
+		 */
+		if (!((entrylo0 | entrylo1) & ENTRYLO_G) && (mmid != asid))
+			continue;
+
+		/*
+		 * Only print entries in use
+		 */
+		printk("Index: %2d pgmask=%s ", i, msk2str(pagemask));
+
+		c0 = (entrylo0 & ENTRYLO_C) >> ENTRYLO_C_SHIFT;
+		c1 = (entrylo1 & ENTRYLO_C) >> ENTRYLO_C_SHIFT;
+
+		pr_cont("va=%0*lx asid=%0*lx",
+			vwidth, (entryhi & ~0x1fffUL),
+			asidwidth, mmid);
+		if (cpu_has_guestid)
+			pr_cont(" gid=%02lx",
+				(guestctl1 & MIPS_GCTL1_RID)
+					>> MIPS_GCTL1_RID_SHIFT);
+		/* RI/XI are in awkward places, so mask them off separately */
+		pa = entrylo0 & ~(MIPS_ENTRYLO_RI | MIPS_ENTRYLO_XI);
+		if (xpa)
+			pa |= (unsigned long long)readx_c0_entrylo0() << 30;
+		pa = (pa << 6) & PAGE_MASK;
+		pr_cont("\n\t[");
+		if (cpu_has_rixi)
+			pr_cont("ri=%d xi=%d ",
+				(entrylo0 & MIPS_ENTRYLO_RI) ? 1 : 0,
+				(entrylo0 & MIPS_ENTRYLO_XI) ? 1 : 0);
+		pr_cont("pa=%0*llx c=%d d=%d v=%d g=%d] [",
+			pwidth, pa, c0,
+			(entrylo0 & ENTRYLO_D) ? 1 : 0,
+			(entrylo0 & ENTRYLO_V) ? 1 : 0,
+			(entrylo0 & ENTRYLO_G) ? 1 : 0);
+		/* RI/XI are in awkward places, so mask them off separately */
+		pa = entrylo1 & ~(MIPS_ENTRYLO_RI | MIPS_ENTRYLO_XI);
+		if (xpa)
+			pa |= (unsigned long long)readx_c0_entrylo1() << 30;
+		pa = (pa << 6) & PAGE_MASK;
+		if (cpu_has_rixi)
+			pr_cont("ri=%d xi=%d ",
+				(entrylo1 & MIPS_ENTRYLO_RI) ? 1 : 0,
+				(entrylo1 & MIPS_ENTRYLO_XI) ? 1 : 0);
+		pr_cont("pa=%0*llx c=%d d=%d v=%d g=%d]\n",
+			pwidth, pa, c1,
+			(entrylo1 & ENTRYLO_D) ? 1 : 0,
+			(entrylo1 & ENTRYLO_V) ? 1 : 0,
+			(entrylo1 & ENTRYLO_G) ? 1 : 0);
+	}
+	printk("\n");
+
+	write_c0_entryhi(s_entryhi);
+	write_c0_index(s_index);
+	write_c0_pagemask(s_pagemask);
+	if (cpu_has_guestid)
+		write_c0_guestctl1(s_guestctl1);
+}
+
+void dump_tlb_all(void)
+{
+	dump_tlb(0, current_cpu_data.tlbsize - 1);
+}
diff --git a/arch/mips/lib/iomap-pci.c b/arch/mips/lib/iomap-pci.c
new file mode 100644
index 000000000..a9cb28813
--- /dev/null
+++ b/arch/mips/lib/iomap-pci.c
@@ -0,0 +1,46 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Implement the default iomap interfaces
+ *
+ * (C) Copyright 2004 Linus Torvalds
+ * (C) Copyright 2006 Ralf Baechle <ralf@linux-mips.org>
+ * (C) Copyright 2007 MIPS Technologies, Inc.
+ *     written by Ralf Baechle <ralf@linux-mips.org>
+ */
+#include <linux/pci.h>
+#include <linux/export.h>
+#include <asm/io.h>
+
+#ifdef CONFIG_PCI_DRIVERS_LEGACY
+
+void __iomem *__pci_ioport_map(struct pci_dev *dev,
+			       unsigned long port, unsigned int nr)
+{
+	struct pci_controller *ctrl = dev->bus->sysdata;
+	unsigned long base = ctrl->io_map_base;
+
+	/* This will eventually become a BUG_ON but for now be gentle */
+	if (unlikely(!ctrl->io_map_base)) {
+		struct pci_bus *bus = dev->bus;
+		char name[8];
+
+		while (bus->parent)
+			bus = bus->parent;
+
+		ctrl->io_map_base = base = mips_io_port_base;
+
+		sprintf(name, "%04x:%02x", pci_domain_nr(bus), bus->number);
+		printk(KERN_WARNING "io_map_base of root PCI bus %s unset.  "
+		       "Trying to continue but you better\nfix this issue or "
+		       "report it to linux-mips@vger.kernel.org or your "
+		       "vendor.\n", name);
+#ifdef CONFIG_PCI_DOMAINS
+		panic("To avoid data corruption io_map_base MUST be set with "
+		      "multiple PCI domains.");
+#endif
+	}
+
+	return (void __iomem *) (ctrl->io_map_base + port);
+}
+
+#endif /* CONFIG_PCI_DRIVERS_LEGACY */
diff --git a/arch/mips/lib/iomap_copy.c b/arch/mips/lib/iomap_copy.c
new file mode 100644
index 000000000..157500a09
--- /dev/null
+++ b/arch/mips/lib/iomap_copy.c
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/export.h>
+#include <linux/io.h>
+
+/**
+ * __ioread64_copy - copy data from MMIO space, in 64-bit units
+ * @to: destination (must be 64-bit aligned)
+ * @from: source, in MMIO space (must be 64-bit aligned)
+ * @count: number of 64-bit quantities to copy
+ *
+ * Copy data from MMIO space to kernel space, in units of 32 or 64 bits at a
+ * time.  Order of access is not guaranteed, nor is a memory barrier
+ * performed afterwards.
+ */
+void __ioread64_copy(void *to, const void __iomem *from, size_t count)
+{
+#ifdef CONFIG_64BIT
+	u64 *dst = to;
+	const u64 __iomem *src = from;
+	const u64 __iomem *end = src + count;
+
+	while (src < end)
+		*dst++ = __raw_readq(src++);
+#else
+	__ioread32_copy(to, from, count * 2);
+#endif
+}
+EXPORT_SYMBOL_GPL(__ioread64_copy);
diff --git a/arch/mips/lib/libgcc.h b/arch/mips/lib/libgcc.h
new file mode 100644
index 000000000..199a7f962
--- /dev/null
+++ b/arch/mips/lib/libgcc.h
@@ -0,0 +1,43 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_LIBGCC_H
+#define __ASM_LIBGCC_H
+
+#include <asm/byteorder.h>
+
+typedef int word_type __attribute__ ((mode (__word__)));
+
+#ifdef __BIG_ENDIAN
+struct DWstruct {
+	int high, low;
+};
+
+struct TWstruct {
+	long long high, low;
+};
+#elif defined(__LITTLE_ENDIAN)
+struct DWstruct {
+	int low, high;
+};
+
+struct TWstruct {
+	long long low, high;
+};
+#else
+#error I feel sick.
+#endif
+
+typedef union {
+	struct DWstruct s;
+	long long ll;
+} DWunion;
+
+#if defined(CONFIG_64BIT) && defined(CONFIG_CPU_MIPSR6)
+typedef int ti_type __attribute__((mode(TI)));
+
+typedef union {
+	struct TWstruct s;
+	ti_type ti;
+} TWunion;
+#endif
+
+#endif /* __ASM_LIBGCC_H */
diff --git a/arch/mips/lib/memcpy.S b/arch/mips/lib/memcpy.S
new file mode 100644
index 000000000..18a43f2e2
--- /dev/null
+++ b/arch/mips/lib/memcpy.S
@@ -0,0 +1,704 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Unified implementation of memcpy, memmove and the __copy_user backend.
+ *
+ * Copyright (C) 1998, 99, 2000, 01, 2002 Ralf Baechle (ralf@gnu.org)
+ * Copyright (C) 1999, 2000, 01, 2002 Silicon Graphics, Inc.
+ * Copyright (C) 2002 Broadcom, Inc.
+ *   memcpy/copy_user author: Mark Vandevoorde
+ * Copyright (C) 2007  Maciej W. Rozycki
+ * Copyright (C) 2014 Imagination Technologies Ltd.
+ *
+ * Mnemonic names for arguments to memcpy/__copy_user
+ */
+
+/*
+ * Hack to resolve longstanding prefetch issue
+ *
+ * Prefetching may be fatal on some systems if we're prefetching beyond the
+ * end of memory on some systems.  It's also a seriously bad idea on non
+ * dma-coherent systems.
+ */
+#ifdef CONFIG_DMA_NONCOHERENT
+#undef CONFIG_CPU_HAS_PREFETCH
+#endif
+#ifdef CONFIG_MIPS_MALTA
+#undef CONFIG_CPU_HAS_PREFETCH
+#endif
+#ifdef CONFIG_CPU_MIPSR6
+#undef CONFIG_CPU_HAS_PREFETCH
+#endif
+
+#include <asm/asm.h>
+#include <asm/asm-offsets.h>
+#include <asm/export.h>
+#include <asm/regdef.h>
+
+#define dst a0
+#define src a1
+#define len a2
+
+/*
+ * Spec
+ *
+ * memcpy copies len bytes from src to dst and sets v0 to dst.
+ * It assumes that
+ *   - src and dst don't overlap
+ *   - src is readable
+ *   - dst is writable
+ * memcpy uses the standard calling convention
+ *
+ * __copy_user copies up to len bytes from src to dst and sets a2 (len) to
+ * the number of uncopied bytes due to an exception caused by a read or write.
+ * __copy_user assumes that src and dst don't overlap, and that the call is
+ * implementing one of the following:
+ *   copy_to_user
+ *     - src is readable  (no exceptions when reading src)
+ *   copy_from_user
+ *     - dst is writable  (no exceptions when writing dst)
+ * __copy_user uses a non-standard calling convention; see
+ * include/asm-mips/uaccess.h
+ *
+ * When an exception happens on a load, the handler must
+ # ensure that all of the destination buffer is overwritten to prevent
+ * leaking information to user mode programs.
+ */
+
+/*
+ * Implementation
+ */
+
+/*
+ * The exception handler for loads requires that:
+ *  1- AT contain the address of the byte just past the end of the source
+ *     of the copy,
+ *  2- src_entry <= src < AT, and
+ *  3- (dst - src) == (dst_entry - src_entry),
+ * The _entry suffix denotes values when __copy_user was called.
+ *
+ * (1) is set up up by uaccess.h and maintained by not writing AT in copy_user
+ * (2) is met by incrementing src by the number of bytes copied
+ * (3) is met by not doing loads between a pair of increments of dst and src
+ *
+ * The exception handlers for stores adjust len (if necessary) and return.
+ * These handlers do not need to overwrite any data.
+ *
+ * For __rmemcpy and memmove an exception is always a kernel bug, therefore
+ * they're not protected.
+ */
+
+/* Instruction type */
+#define LD_INSN 1
+#define ST_INSN 2
+/* Pretech type */
+#define SRC_PREFETCH 1
+#define DST_PREFETCH 2
+#define LEGACY_MODE 1
+#define EVA_MODE    2
+#define USEROP   1
+#define KERNELOP 2
+
+/*
+ * Wrapper to add an entry in the exception table
+ * in case the insn causes a memory exception.
+ * Arguments:
+ * insn    : Load/store instruction
+ * type    : Instruction type
+ * reg     : Register
+ * addr    : Address
+ * handler : Exception handler
+ */
+
+#define EXC(insn, type, reg, addr, handler)			\
+	.if \mode == LEGACY_MODE;				\
+9:		insn reg, addr;					\
+		.section __ex_table,"a";			\
+		PTR_WD	9b, handler;				\
+		.previous;					\
+	/* This is assembled in EVA mode */			\
+	.else;							\
+		/* If loading from user or storing to user */	\
+		.if ((\from == USEROP) && (type == LD_INSN)) || \
+		    ((\to == USEROP) && (type == ST_INSN));	\
+9:			__BUILD_EVA_INSN(insn##e, reg, addr);	\
+			.section __ex_table,"a";		\
+			PTR_WD	9b, handler;			\
+			.previous;				\
+		.else;						\
+			/*					\
+			 *  Still in EVA, but no need for	\
+			 * exception handler or EVA insn	\
+			 */					\
+			insn reg, addr;				\
+		.endif;						\
+	.endif
+
+/*
+ * Only on the 64-bit kernel we can made use of 64-bit registers.
+ */
+#ifdef CONFIG_64BIT
+#define USE_DOUBLE
+#endif
+
+#ifdef USE_DOUBLE
+
+#define LOADK ld /* No exception */
+#define LOAD(reg, addr, handler)	EXC(ld, LD_INSN, reg, addr, handler)
+#define LOADL(reg, addr, handler)	EXC(ldl, LD_INSN, reg, addr, handler)
+#define LOADR(reg, addr, handler)	EXC(ldr, LD_INSN, reg, addr, handler)
+#define STOREL(reg, addr, handler)	EXC(sdl, ST_INSN, reg, addr, handler)
+#define STORER(reg, addr, handler)	EXC(sdr, ST_INSN, reg, addr, handler)
+#define STORE(reg, addr, handler)	EXC(sd, ST_INSN, reg, addr, handler)
+#define ADD    daddu
+#define SUB    dsubu
+#define SRL    dsrl
+#define SRA    dsra
+#define SLL    dsll
+#define SLLV   dsllv
+#define SRLV   dsrlv
+#define NBYTES 8
+#define LOG_NBYTES 3
+
+/*
+ * As we are sharing code base with the mips32 tree (which use the o32 ABI
+ * register definitions). We need to redefine the register definitions from
+ * the n64 ABI register naming to the o32 ABI register naming.
+ */
+#undef t0
+#undef t1
+#undef t2
+#undef t3
+#define t0	$8
+#define t1	$9
+#define t2	$10
+#define t3	$11
+#define t4	$12
+#define t5	$13
+#define t6	$14
+#define t7	$15
+
+#else
+
+#define LOADK lw /* No exception */
+#define LOAD(reg, addr, handler)	EXC(lw, LD_INSN, reg, addr, handler)
+#define LOADL(reg, addr, handler)	EXC(lwl, LD_INSN, reg, addr, handler)
+#define LOADR(reg, addr, handler)	EXC(lwr, LD_INSN, reg, addr, handler)
+#define STOREL(reg, addr, handler)	EXC(swl, ST_INSN, reg, addr, handler)
+#define STORER(reg, addr, handler)	EXC(swr, ST_INSN, reg, addr, handler)
+#define STORE(reg, addr, handler)	EXC(sw, ST_INSN, reg, addr, handler)
+#define ADD    addu
+#define SUB    subu
+#define SRL    srl
+#define SLL    sll
+#define SRA    sra
+#define SLLV   sllv
+#define SRLV   srlv
+#define NBYTES 4
+#define LOG_NBYTES 2
+
+#endif /* USE_DOUBLE */
+
+#define LOADB(reg, addr, handler)	EXC(lb, LD_INSN, reg, addr, handler)
+#define STOREB(reg, addr, handler)	EXC(sb, ST_INSN, reg, addr, handler)
+
+#ifdef CONFIG_CPU_HAS_PREFETCH
+# define _PREF(hint, addr, type)					\
+	.if \mode == LEGACY_MODE;					\
+		kernel_pref(hint, addr);				\
+	.else;								\
+		.if ((\from == USEROP) && (type == SRC_PREFETCH)) ||	\
+		    ((\to == USEROP) && (type == DST_PREFETCH));	\
+			/*						\
+			 * PREFE has only 9 bits for the offset		\
+			 * compared to PREF which has 16, so it may	\
+			 * need to use the $at register but this	\
+			 * register should remain intact because it's	\
+			 * used later on. Therefore use $v1.		\
+			 */						\
+			.set at=v1;					\
+			user_pref(hint, addr);				\
+			.set noat;					\
+		.else;							\
+			kernel_pref(hint, addr);			\
+		.endif;							\
+	.endif
+#else
+# define _PREF(hint, addr, type)
+#endif
+
+#define PREFS(hint, addr) _PREF(hint, addr, SRC_PREFETCH)
+#define PREFD(hint, addr) _PREF(hint, addr, DST_PREFETCH)
+
+#ifdef CONFIG_CPU_LITTLE_ENDIAN
+#define LDFIRST LOADR
+#define LDREST	LOADL
+#define STFIRST STORER
+#define STREST	STOREL
+#define SHIFT_DISCARD SLLV
+#else
+#define LDFIRST LOADL
+#define LDREST	LOADR
+#define STFIRST STOREL
+#define STREST	STORER
+#define SHIFT_DISCARD SRLV
+#endif
+
+#define FIRST(unit) ((unit)*NBYTES)
+#define REST(unit)  (FIRST(unit)+NBYTES-1)
+#define UNIT(unit)  FIRST(unit)
+
+#define ADDRMASK (NBYTES-1)
+
+	.text
+	.set	noreorder
+#ifndef CONFIG_CPU_DADDI_WORKAROUNDS
+	.set	noat
+#else
+	.set	at=v1
+#endif
+
+	.align	5
+
+	/*
+	 * Macro to build the __copy_user common code
+	 * Arguments:
+	 * mode : LEGACY_MODE or EVA_MODE
+	 * from : Source operand. USEROP or KERNELOP
+	 * to   : Destination operand. USEROP or KERNELOP
+	 */
+	.macro __BUILD_COPY_USER mode, from, to
+
+	/* initialize __memcpy if this the first time we execute this macro */
+	.ifnotdef __memcpy
+	.set __memcpy, 1
+	.hidden __memcpy /* make sure it does not leak */
+	.endif
+
+	/*
+	 * Note: dst & src may be unaligned, len may be 0
+	 * Temps
+	 */
+#define rem t8
+
+	R10KCBARRIER(0(ra))
+	/*
+	 * The "issue break"s below are very approximate.
+	 * Issue delays for dcache fills will perturb the schedule, as will
+	 * load queue full replay traps, etc.
+	 *
+	 * If len < NBYTES use byte operations.
+	 */
+	PREFS(	0, 0(src) )
+	PREFD(	1, 0(dst) )
+	sltu	t2, len, NBYTES
+	and	t1, dst, ADDRMASK
+	PREFS(	0, 1*32(src) )
+	PREFD(	1, 1*32(dst) )
+	bnez	t2, .Lcopy_bytes_checklen\@
+	 and	t0, src, ADDRMASK
+	PREFS(	0, 2*32(src) )
+	PREFD(	1, 2*32(dst) )
+#ifndef CONFIG_CPU_NO_LOAD_STORE_LR
+	bnez	t1, .Ldst_unaligned\@
+	 nop
+	bnez	t0, .Lsrc_unaligned_dst_aligned\@
+#else /* CONFIG_CPU_NO_LOAD_STORE_LR */
+	or	t0, t0, t1
+	bnez	t0, .Lcopy_unaligned_bytes\@
+#endif /* CONFIG_CPU_NO_LOAD_STORE_LR */
+	/*
+	 * use delay slot for fall-through
+	 * src and dst are aligned; need to compute rem
+	 */
+.Lboth_aligned\@:
+	 SRL	t0, len, LOG_NBYTES+3	 # +3 for 8 units/iter
+	beqz	t0, .Lcleanup_both_aligned\@ # len < 8*NBYTES
+	 and	rem, len, (8*NBYTES-1)	 # rem = len % (8*NBYTES)
+	PREFS(	0, 3*32(src) )
+	PREFD(	1, 3*32(dst) )
+	.align	4
+1:
+	R10KCBARRIER(0(ra))
+	LOAD(t0, UNIT(0)(src), .Ll_exc\@)
+	LOAD(t1, UNIT(1)(src), .Ll_exc_copy\@)
+	LOAD(t2, UNIT(2)(src), .Ll_exc_copy\@)
+	LOAD(t3, UNIT(3)(src), .Ll_exc_copy\@)
+	SUB	len, len, 8*NBYTES
+	LOAD(t4, UNIT(4)(src), .Ll_exc_copy\@)
+	LOAD(t7, UNIT(5)(src), .Ll_exc_copy\@)
+	STORE(t0, UNIT(0)(dst),	.Ls_exc_p8u\@)
+	STORE(t1, UNIT(1)(dst),	.Ls_exc_p7u\@)
+	LOAD(t0, UNIT(6)(src), .Ll_exc_copy\@)
+	LOAD(t1, UNIT(7)(src), .Ll_exc_copy\@)
+	ADD	src, src, 8*NBYTES
+	ADD	dst, dst, 8*NBYTES
+	STORE(t2, UNIT(-6)(dst), .Ls_exc_p6u\@)
+	STORE(t3, UNIT(-5)(dst), .Ls_exc_p5u\@)
+	STORE(t4, UNIT(-4)(dst), .Ls_exc_p4u\@)
+	STORE(t7, UNIT(-3)(dst), .Ls_exc_p3u\@)
+	STORE(t0, UNIT(-2)(dst), .Ls_exc_p2u\@)
+	STORE(t1, UNIT(-1)(dst), .Ls_exc_p1u\@)
+	PREFS(	0, 8*32(src) )
+	PREFD(	1, 8*32(dst) )
+	bne	len, rem, 1b
+	 nop
+
+	/*
+	 * len == rem == the number of bytes left to copy < 8*NBYTES
+	 */
+.Lcleanup_both_aligned\@:
+	beqz	len, .Ldone\@
+	 sltu	t0, len, 4*NBYTES
+	bnez	t0, .Lless_than_4units\@
+	 and	rem, len, (NBYTES-1)	# rem = len % NBYTES
+	/*
+	 * len >= 4*NBYTES
+	 */
+	LOAD( t0, UNIT(0)(src),	.Ll_exc\@)
+	LOAD( t1, UNIT(1)(src),	.Ll_exc_copy\@)
+	LOAD( t2, UNIT(2)(src),	.Ll_exc_copy\@)
+	LOAD( t3, UNIT(3)(src),	.Ll_exc_copy\@)
+	SUB	len, len, 4*NBYTES
+	ADD	src, src, 4*NBYTES
+	R10KCBARRIER(0(ra))
+	STORE(t0, UNIT(0)(dst),	.Ls_exc_p4u\@)
+	STORE(t1, UNIT(1)(dst),	.Ls_exc_p3u\@)
+	STORE(t2, UNIT(2)(dst),	.Ls_exc_p2u\@)
+	STORE(t3, UNIT(3)(dst),	.Ls_exc_p1u\@)
+	.set	reorder				/* DADDI_WAR */
+	ADD	dst, dst, 4*NBYTES
+	beqz	len, .Ldone\@
+	.set	noreorder
+.Lless_than_4units\@:
+	/*
+	 * rem = len % NBYTES
+	 */
+	beq	rem, len, .Lcopy_bytes\@
+	 nop
+1:
+	R10KCBARRIER(0(ra))
+	LOAD(t0, 0(src), .Ll_exc\@)
+	ADD	src, src, NBYTES
+	SUB	len, len, NBYTES
+	STORE(t0, 0(dst), .Ls_exc_p1u\@)
+	.set	reorder				/* DADDI_WAR */
+	ADD	dst, dst, NBYTES
+	bne	rem, len, 1b
+	.set	noreorder
+
+#ifndef CONFIG_CPU_NO_LOAD_STORE_LR
+	/*
+	 * src and dst are aligned, need to copy rem bytes (rem < NBYTES)
+	 * A loop would do only a byte at a time with possible branch
+	 * mispredicts.	 Can't do an explicit LOAD dst,mask,or,STORE
+	 * because can't assume read-access to dst.  Instead, use
+	 * STREST dst, which doesn't require read access to dst.
+	 *
+	 * This code should perform better than a simple loop on modern,
+	 * wide-issue mips processors because the code has fewer branches and
+	 * more instruction-level parallelism.
+	 */
+#define bits t2
+	beqz	len, .Ldone\@
+	 ADD	t1, dst, len	# t1 is just past last byte of dst
+	li	bits, 8*NBYTES
+	SLL	rem, len, 3	# rem = number of bits to keep
+	LOAD(t0, 0(src), .Ll_exc\@)
+	SUB	bits, bits, rem # bits = number of bits to discard
+	SHIFT_DISCARD t0, t0, bits
+	STREST(t0, -1(t1), .Ls_exc\@)
+	jr	ra
+	 move	len, zero
+.Ldst_unaligned\@:
+	/*
+	 * dst is unaligned
+	 * t0 = src & ADDRMASK
+	 * t1 = dst & ADDRMASK; T1 > 0
+	 * len >= NBYTES
+	 *
+	 * Copy enough bytes to align dst
+	 * Set match = (src and dst have same alignment)
+	 */
+#define match rem
+	LDFIRST(t3, FIRST(0)(src), .Ll_exc\@)
+	ADD	t2, zero, NBYTES
+	LDREST(t3, REST(0)(src), .Ll_exc_copy\@)
+	SUB	t2, t2, t1	# t2 = number of bytes copied
+	xor	match, t0, t1
+	R10KCBARRIER(0(ra))
+	STFIRST(t3, FIRST(0)(dst), .Ls_exc\@)
+	beq	len, t2, .Ldone\@
+	 SUB	len, len, t2
+	ADD	dst, dst, t2
+	beqz	match, .Lboth_aligned\@
+	 ADD	src, src, t2
+
+.Lsrc_unaligned_dst_aligned\@:
+	SRL	t0, len, LOG_NBYTES+2	 # +2 for 4 units/iter
+	PREFS(	0, 3*32(src) )
+	beqz	t0, .Lcleanup_src_unaligned\@
+	 and	rem, len, (4*NBYTES-1)	 # rem = len % 4*NBYTES
+	PREFD(	1, 3*32(dst) )
+1:
+/*
+ * Avoid consecutive LD*'s to the same register since some mips
+ * implementations can't issue them in the same cycle.
+ * It's OK to load FIRST(N+1) before REST(N) because the two addresses
+ * are to the same unit (unless src is aligned, but it's not).
+ */
+	R10KCBARRIER(0(ra))
+	LDFIRST(t0, FIRST(0)(src), .Ll_exc\@)
+	LDFIRST(t1, FIRST(1)(src), .Ll_exc_copy\@)
+	SUB	len, len, 4*NBYTES
+	LDREST(t0, REST(0)(src), .Ll_exc_copy\@)
+	LDREST(t1, REST(1)(src), .Ll_exc_copy\@)
+	LDFIRST(t2, FIRST(2)(src), .Ll_exc_copy\@)
+	LDFIRST(t3, FIRST(3)(src), .Ll_exc_copy\@)
+	LDREST(t2, REST(2)(src), .Ll_exc_copy\@)
+	LDREST(t3, REST(3)(src), .Ll_exc_copy\@)
+	PREFS(	0, 9*32(src) )		# 0 is PREF_LOAD  (not streamed)
+	ADD	src, src, 4*NBYTES
+#ifdef CONFIG_CPU_SB1
+	nop				# improves slotting
+#endif
+	STORE(t0, UNIT(0)(dst),	.Ls_exc_p4u\@)
+	STORE(t1, UNIT(1)(dst),	.Ls_exc_p3u\@)
+	STORE(t2, UNIT(2)(dst),	.Ls_exc_p2u\@)
+	STORE(t3, UNIT(3)(dst),	.Ls_exc_p1u\@)
+	PREFD(	1, 9*32(dst) )		# 1 is PREF_STORE (not streamed)
+	.set	reorder				/* DADDI_WAR */
+	ADD	dst, dst, 4*NBYTES
+	bne	len, rem, 1b
+	.set	noreorder
+
+.Lcleanup_src_unaligned\@:
+	beqz	len, .Ldone\@
+	 and	rem, len, NBYTES-1  # rem = len % NBYTES
+	beq	rem, len, .Lcopy_bytes\@
+	 nop
+1:
+	R10KCBARRIER(0(ra))
+	LDFIRST(t0, FIRST(0)(src), .Ll_exc\@)
+	LDREST(t0, REST(0)(src), .Ll_exc_copy\@)
+	ADD	src, src, NBYTES
+	SUB	len, len, NBYTES
+	STORE(t0, 0(dst), .Ls_exc_p1u\@)
+	.set	reorder				/* DADDI_WAR */
+	ADD	dst, dst, NBYTES
+	bne	len, rem, 1b
+	.set	noreorder
+
+#endif /* !CONFIG_CPU_NO_LOAD_STORE_LR */
+.Lcopy_bytes_checklen\@:
+	beqz	len, .Ldone\@
+	 nop
+.Lcopy_bytes\@:
+	/* 0 < len < NBYTES  */
+	R10KCBARRIER(0(ra))
+#define COPY_BYTE(N)			\
+	LOADB(t0, N(src), .Ll_exc\@);	\
+	SUB	len, len, 1;		\
+	beqz	len, .Ldone\@;		\
+	STOREB(t0, N(dst), .Ls_exc_p1\@)
+
+	COPY_BYTE(0)
+	COPY_BYTE(1)
+#ifdef USE_DOUBLE
+	COPY_BYTE(2)
+	COPY_BYTE(3)
+	COPY_BYTE(4)
+	COPY_BYTE(5)
+#endif
+	LOADB(t0, NBYTES-2(src), .Ll_exc\@)
+	SUB	len, len, 1
+	jr	ra
+	STOREB(t0, NBYTES-2(dst), .Ls_exc_p1\@)
+.Ldone\@:
+	jr	ra
+	 nop
+
+#ifdef CONFIG_CPU_NO_LOAD_STORE_LR
+.Lcopy_unaligned_bytes\@:
+1:
+	COPY_BYTE(0)
+	COPY_BYTE(1)
+	COPY_BYTE(2)
+	COPY_BYTE(3)
+	COPY_BYTE(4)
+	COPY_BYTE(5)
+	COPY_BYTE(6)
+	COPY_BYTE(7)
+	ADD	src, src, 8
+	b	1b
+	 ADD	dst, dst, 8
+#endif /* CONFIG_CPU_NO_LOAD_STORE_LR */
+	.if __memcpy == 1
+	END(memcpy)
+	.set __memcpy, 0
+	.hidden __memcpy
+	.endif
+
+.Ll_exc_copy\@:
+	/*
+	 * Copy bytes from src until faulting load address (or until a
+	 * lb faults)
+	 *
+	 * When reached by a faulting LDFIRST/LDREST, THREAD_BUADDR($28)
+	 * may be more than a byte beyond the last address.
+	 * Hence, the lb below may get an exception.
+	 *
+	 * Assumes src < THREAD_BUADDR($28)
+	 */
+	LOADK	t0, TI_TASK($28)
+	 nop
+	LOADK	t0, THREAD_BUADDR(t0)
+1:
+	LOADB(t1, 0(src), .Ll_exc\@)
+	ADD	src, src, 1
+	sb	t1, 0(dst)	# can't fault -- we're copy_from_user
+	.set	reorder				/* DADDI_WAR */
+	ADD	dst, dst, 1
+	bne	src, t0, 1b
+	.set	noreorder
+.Ll_exc\@:
+	LOADK	t0, TI_TASK($28)
+	 nop
+	LOADK	t0, THREAD_BUADDR(t0)	# t0 is just past last good address
+	 nop
+	SUB	len, AT, t0		# len number of uncopied bytes
+	jr	ra
+	 nop
+
+#define SEXC(n)							\
+	.set	reorder;			/* DADDI_WAR */ \
+.Ls_exc_p ## n ## u\@:						\
+	ADD	len, len, n*NBYTES;				\
+	jr	ra;						\
+	.set	noreorder
+
+SEXC(8)
+SEXC(7)
+SEXC(6)
+SEXC(5)
+SEXC(4)
+SEXC(3)
+SEXC(2)
+SEXC(1)
+
+.Ls_exc_p1\@:
+	.set	reorder				/* DADDI_WAR */
+	ADD	len, len, 1
+	jr	ra
+	.set	noreorder
+.Ls_exc\@:
+	jr	ra
+	 nop
+	.endm
+
+#ifndef CONFIG_HAVE_PLAT_MEMCPY
+	.align	5
+LEAF(memmove)
+EXPORT_SYMBOL(memmove)
+	ADD	t0, a0, a2
+	ADD	t1, a1, a2
+	sltu	t0, a1, t0			# dst + len <= src -> memcpy
+	sltu	t1, a0, t1			# dst >= src + len -> memcpy
+	and	t0, t1
+	beqz	t0, .L__memcpy
+	 move	v0, a0				/* return value */
+	beqz	a2, .Lr_out
+	END(memmove)
+
+	/* fall through to __rmemcpy */
+LEAF(__rmemcpy)					/* a0=dst a1=src a2=len */
+	 sltu	t0, a1, a0
+	beqz	t0, .Lr_end_bytes_up		# src >= dst
+	 nop
+	ADD	a0, a2				# dst = dst + len
+	ADD	a1, a2				# src = src + len
+
+.Lr_end_bytes:
+	R10KCBARRIER(0(ra))
+	lb	t0, -1(a1)
+	SUB	a2, a2, 0x1
+	sb	t0, -1(a0)
+	SUB	a1, a1, 0x1
+	.set	reorder				/* DADDI_WAR */
+	SUB	a0, a0, 0x1
+	bnez	a2, .Lr_end_bytes
+	.set	noreorder
+
+.Lr_out:
+	jr	ra
+	 move	a2, zero
+
+.Lr_end_bytes_up:
+	R10KCBARRIER(0(ra))
+	lb	t0, (a1)
+	SUB	a2, a2, 0x1
+	sb	t0, (a0)
+	ADD	a1, a1, 0x1
+	.set	reorder				/* DADDI_WAR */
+	ADD	a0, a0, 0x1
+	bnez	a2, .Lr_end_bytes_up
+	.set	noreorder
+
+	jr	ra
+	 move	a2, zero
+	END(__rmemcpy)
+
+/*
+ * A combined memcpy/__copy_user
+ * __copy_user sets len to 0 for success; else to an upper bound of
+ * the number of uncopied bytes.
+ * memcpy sets v0 to dst.
+ */
+	.align	5
+LEAF(memcpy)					/* a0=dst a1=src a2=len */
+EXPORT_SYMBOL(memcpy)
+	move	v0, dst				/* return value */
+.L__memcpy:
+#ifndef CONFIG_EVA
+FEXPORT(__raw_copy_from_user)
+EXPORT_SYMBOL(__raw_copy_from_user)
+FEXPORT(__raw_copy_to_user)
+EXPORT_SYMBOL(__raw_copy_to_user)
+#endif
+	/* Legacy Mode, user <-> user */
+	__BUILD_COPY_USER LEGACY_MODE USEROP USEROP
+
+#endif
+
+#ifdef CONFIG_EVA
+
+/*
+ * For EVA we need distinct symbols for reading and writing to user space.
+ * This is because we need to use specific EVA instructions to perform the
+ * virtual <-> physical translation when a virtual address is actually in user
+ * space
+ */
+
+/*
+ * __copy_from_user (EVA)
+ */
+
+LEAF(__raw_copy_from_user)
+EXPORT_SYMBOL(__raw_copy_from_user)
+	__BUILD_COPY_USER EVA_MODE USEROP KERNELOP
+END(__raw_copy_from_user)
+
+
+
+/*
+ * __copy_to_user (EVA)
+ */
+
+LEAF(__raw_copy_to_user)
+EXPORT_SYMBOL(__raw_copy_to_user)
+__BUILD_COPY_USER EVA_MODE KERNELOP USEROP
+END(__raw_copy_to_user)
+
+#endif
diff --git a/arch/mips/lib/memset.S b/arch/mips/lib/memset.S
new file mode 100644
index 000000000..0b342bae9
--- /dev/null
+++ b/arch/mips/lib/memset.S
@@ -0,0 +1,325 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1998, 1999, 2000 by Ralf Baechle
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ * Copyright (C) 2007 by Maciej W. Rozycki
+ * Copyright (C) 2011, 2012 MIPS Technologies, Inc.
+ */
+#include <asm/asm.h>
+#include <asm/asm-offsets.h>
+#include <asm/export.h>
+#include <asm/regdef.h>
+
+#if LONGSIZE == 4
+#define LONG_S_L swl
+#define LONG_S_R swr
+#else
+#define LONG_S_L sdl
+#define LONG_S_R sdr
+#endif
+
+#ifdef CONFIG_CPU_MICROMIPS
+#define STORSIZE (LONGSIZE * 2)
+#define STORMASK (STORSIZE - 1)
+#define FILL64RG t8
+#define FILLPTRG t7
+#undef  LONG_S
+#define LONG_S LONG_SP
+#else
+#define STORSIZE LONGSIZE
+#define STORMASK LONGMASK
+#define FILL64RG a1
+#define FILLPTRG t0
+#endif
+
+#define LEGACY_MODE 1
+#define EVA_MODE    2
+
+/*
+ * No need to protect it with EVA #ifdefery. The generated block of code
+ * will never be assembled if EVA is not enabled.
+ */
+#define __EVAFY(insn, reg, addr) __BUILD_EVA_INSN(insn##e, reg, addr)
+#define ___BUILD_EVA_INSN(insn, reg, addr) __EVAFY(insn, reg, addr)
+
+#define EX(insn,reg,addr,handler)			\
+	.if \mode == LEGACY_MODE;			\
+9:		insn	reg, addr;			\
+	.else;						\
+9:		___BUILD_EVA_INSN(insn, reg, addr);	\
+	.endif;						\
+	.section __ex_table,"a";			\
+	PTR_WD	9b, handler;				\
+	.previous
+
+	.macro	f_fill64 dst, offset, val, fixup, mode
+	EX(LONG_S, \val, (\offset +  0 * STORSIZE)(\dst), \fixup)
+	EX(LONG_S, \val, (\offset +  1 * STORSIZE)(\dst), \fixup)
+	EX(LONG_S, \val, (\offset +  2 * STORSIZE)(\dst), \fixup)
+	EX(LONG_S, \val, (\offset +  3 * STORSIZE)(\dst), \fixup)
+#if ((defined(CONFIG_CPU_MICROMIPS) && (LONGSIZE == 4)) || !defined(CONFIG_CPU_MICROMIPS))
+	EX(LONG_S, \val, (\offset +  4 * STORSIZE)(\dst), \fixup)
+	EX(LONG_S, \val, (\offset +  5 * STORSIZE)(\dst), \fixup)
+	EX(LONG_S, \val, (\offset +  6 * STORSIZE)(\dst), \fixup)
+	EX(LONG_S, \val, (\offset +  7 * STORSIZE)(\dst), \fixup)
+#endif
+#if (!defined(CONFIG_CPU_MICROMIPS) && (LONGSIZE == 4))
+	EX(LONG_S, \val, (\offset +  8 * STORSIZE)(\dst), \fixup)
+	EX(LONG_S, \val, (\offset +  9 * STORSIZE)(\dst), \fixup)
+	EX(LONG_S, \val, (\offset + 10 * STORSIZE)(\dst), \fixup)
+	EX(LONG_S, \val, (\offset + 11 * STORSIZE)(\dst), \fixup)
+	EX(LONG_S, \val, (\offset + 12 * STORSIZE)(\dst), \fixup)
+	EX(LONG_S, \val, (\offset + 13 * STORSIZE)(\dst), \fixup)
+	EX(LONG_S, \val, (\offset + 14 * STORSIZE)(\dst), \fixup)
+	EX(LONG_S, \val, (\offset + 15 * STORSIZE)(\dst), \fixup)
+#endif
+	.endm
+
+	.align	5
+
+	/*
+	 * Macro to generate the __bzero{,_user} symbol
+	 * Arguments:
+	 * mode: LEGACY_MODE or EVA_MODE
+	 */
+	.macro __BUILD_BZERO mode
+	/* Initialize __memset if this is the first time we call this macro */
+	.ifnotdef __memset
+	.set __memset, 1
+	.hidden __memset /* Make sure it does not leak */
+	.endif
+
+	sltiu		t0, a2, STORSIZE	/* very small region? */
+	.set		noreorder
+	bnez		t0, .Lsmall_memset\@
+	 andi		t0, a0, STORMASK	/* aligned? */
+	.set		reorder
+
+#ifdef CONFIG_CPU_MICROMIPS
+	move		t8, a1			/* used by 'swp' instruction */
+	move		t9, a1
+#endif
+	.set		noreorder
+#ifndef CONFIG_CPU_DADDI_WORKAROUNDS
+	beqz		t0, 1f
+	 PTR_SUBU	t0, STORSIZE		/* alignment in bytes */
+#else
+	.set		noat
+	li		AT, STORSIZE
+	beqz		t0, 1f
+	 PTR_SUBU	t0, AT			/* alignment in bytes */
+	.set		at
+#endif
+	.set		reorder
+
+#ifndef CONFIG_CPU_NO_LOAD_STORE_LR
+	R10KCBARRIER(0(ra))
+#ifdef __MIPSEB__
+	EX(LONG_S_L, a1, (a0), .Lfirst_fixup\@)	/* make word/dword aligned */
+#else
+	EX(LONG_S_R, a1, (a0), .Lfirst_fixup\@)	/* make word/dword aligned */
+#endif
+	PTR_SUBU	a0, t0			/* long align ptr */
+	PTR_ADDU	a2, t0			/* correct size */
+
+#else /* CONFIG_CPU_NO_LOAD_STORE_LR */
+#define STORE_BYTE(N)				\
+	EX(sb, a1, N(a0), .Lbyte_fixup\@);	\
+	.set		noreorder;		\
+	beqz		t0, 0f;			\
+	 PTR_ADDU	t0, 1;			\
+	.set		reorder;
+
+	PTR_ADDU	a2, t0			/* correct size */
+	PTR_ADDU	t0, 1
+	STORE_BYTE(0)
+	STORE_BYTE(1)
+#if LONGSIZE == 4
+	EX(sb, a1, 2(a0), .Lbyte_fixup\@)
+#else
+	STORE_BYTE(2)
+	STORE_BYTE(3)
+	STORE_BYTE(4)
+	STORE_BYTE(5)
+	EX(sb, a1, 6(a0), .Lbyte_fixup\@)
+#endif
+0:
+	ori		a0, STORMASK
+	xori		a0, STORMASK
+	PTR_ADDIU	a0, STORSIZE
+#endif /* CONFIG_CPU_NO_LOAD_STORE_LR */
+1:	ori		t1, a2, 0x3f		/* # of full blocks */
+	xori		t1, 0x3f
+	andi		t0, a2, 0x40-STORSIZE
+	beqz		t1, .Lmemset_partial\@	/* no block to fill */
+
+	PTR_ADDU	t1, a0			/* end address */
+1:	PTR_ADDIU	a0, 64
+	R10KCBARRIER(0(ra))
+	f_fill64 a0, -64, FILL64RG, .Lfwd_fixup\@, \mode
+	bne		t1, a0, 1b
+
+.Lmemset_partial\@:
+	R10KCBARRIER(0(ra))
+	PTR_LA		t1, 2f			/* where to start */
+#ifdef CONFIG_CPU_MICROMIPS
+	LONG_SRL	t7, t0, 1
+#endif
+#if LONGSIZE == 4
+	PTR_SUBU	t1, FILLPTRG
+#else
+	.set		noat
+	LONG_SRL	AT, FILLPTRG, 1
+	PTR_SUBU	t1, AT
+	.set		at
+#endif
+	PTR_ADDU	a0, t0			/* dest ptr */
+	jr		t1
+
+	/* ... but first do longs ... */
+	f_fill64 a0, -64, FILL64RG, .Lpartial_fixup\@, \mode
+2:	andi		a2, STORMASK		/* At most one long to go */
+
+	.set		noreorder
+	beqz		a2, 1f
+#ifndef CONFIG_CPU_NO_LOAD_STORE_LR
+	 PTR_ADDU	a0, a2			/* What's left */
+	.set		reorder
+	R10KCBARRIER(0(ra))
+#ifdef __MIPSEB__
+	EX(LONG_S_R, a1, -1(a0), .Llast_fixup\@)
+#else
+	EX(LONG_S_L, a1, -1(a0), .Llast_fixup\@)
+#endif
+#else /* CONFIG_CPU_NO_LOAD_STORE_LR */
+	 PTR_SUBU	t0, $0, a2
+	.set		reorder
+	move		a2, zero		/* No remaining longs */
+	PTR_ADDIU	t0, 1
+	STORE_BYTE(0)
+	STORE_BYTE(1)
+#if LONGSIZE == 4
+	EX(sb, a1, 2(a0), .Lbyte_fixup\@)
+#else
+	STORE_BYTE(2)
+	STORE_BYTE(3)
+	STORE_BYTE(4)
+	STORE_BYTE(5)
+	EX(sb, a1, 6(a0), .Lbyte_fixup\@)
+#endif
+0:
+#endif /* CONFIG_CPU_NO_LOAD_STORE_LR */
+1:	move		a2, zero
+	jr		ra
+
+.Lsmall_memset\@:
+	PTR_ADDU	t1, a0, a2
+	beqz		a2, 2f
+
+1:	PTR_ADDIU	a0, 1			/* fill bytewise */
+	R10KCBARRIER(0(ra))
+	.set		noreorder
+	bne		t1, a0, 1b
+	 EX(sb, a1, -1(a0), .Lsmall_fixup\@)
+	.set		reorder
+
+2:	move		a2, zero
+	jr		ra			/* done */
+	.if __memset == 1
+	END(memset)
+	.set __memset, 0
+	.hidden __memset
+	.endif
+
+#ifdef CONFIG_CPU_NO_LOAD_STORE_LR
+.Lbyte_fixup\@:
+	/*
+	 * unset_bytes = (#bytes - (#unaligned bytes)) - (-#unaligned bytes remaining + 1) + 1
+	 *      a2     =             a2                -              t0                   + 1
+	 */
+	PTR_SUBU	a2, t0
+	PTR_ADDIU	a2, 1
+	jr		ra
+#endif /* CONFIG_CPU_NO_LOAD_STORE_LR */
+
+.Lfirst_fixup\@:
+	/* unset_bytes already in a2 */
+	jr	ra
+
+.Lfwd_fixup\@:
+	/*
+	 * unset_bytes = partial_start_addr +  #bytes   -     fault_addr
+	 *      a2     =         t1         + (a2 & 3f) - $28->task->BUADDR
+	 */
+	PTR_L		t0, TI_TASK($28)
+	andi		a2, 0x3f
+	LONG_L		t0, THREAD_BUADDR(t0)
+	LONG_ADDU	a2, t1
+	LONG_SUBU	a2, t0
+	jr		ra
+
+.Lpartial_fixup\@:
+	/*
+	 * unset_bytes = partial_end_addr +      #bytes     -     fault_addr
+	 *      a2     =       a0         + (a2 & STORMASK) - $28->task->BUADDR
+	 */
+	PTR_L		t0, TI_TASK($28)
+	andi		a2, STORMASK
+	LONG_L		t0, THREAD_BUADDR(t0)
+	LONG_ADDU	a2, a0
+	LONG_SUBU	a2, t0
+	jr		ra
+
+.Llast_fixup\@:
+	/* unset_bytes already in a2 */
+	jr		ra
+
+.Lsmall_fixup\@:
+	/*
+	 * unset_bytes = end_addr - current_addr + 1
+	 *      a2     =    t1    -      a0      + 1
+	 */
+	PTR_SUBU	a2, t1, a0
+	PTR_ADDIU	a2, 1
+	jr		ra
+
+	.endm
+
+/*
+ * memset(void *s, int c, size_t n)
+ *
+ * a0: start of area to clear
+ * a1: char to fill with
+ * a2: size of area to clear
+ */
+
+LEAF(memset)
+EXPORT_SYMBOL(memset)
+	move		v0, a0			/* result */
+	beqz		a1, 1f
+
+	andi		a1, 0xff		/* spread fillword */
+	LONG_SLL		t1, a1, 8
+	or		a1, t1
+	LONG_SLL		t1, a1, 16
+#if LONGSIZE == 8
+	or		a1, t1
+	LONG_SLL		t1, a1, 32
+#endif
+	or		a1, t1
+1:
+#ifndef CONFIG_EVA
+FEXPORT(__bzero)
+EXPORT_SYMBOL(__bzero)
+#endif
+	__BUILD_BZERO LEGACY_MODE
+
+#ifdef CONFIG_EVA
+LEAF(__bzero)
+EXPORT_SYMBOL(__bzero)
+	__BUILD_BZERO EVA_MODE
+END(__bzero)
+#endif
diff --git a/arch/mips/lib/mips-atomic.c b/arch/mips/lib/mips-atomic.c
new file mode 100644
index 000000000..a9b72eacf
--- /dev/null
+++ b/arch/mips/lib/mips-atomic.c
@@ -0,0 +1,113 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994, 95, 96, 97, 98, 99, 2003 by Ralf Baechle
+ * Copyright (C) 1996 by Paul M. Antoine
+ * Copyright (C) 1999 Silicon Graphics
+ * Copyright (C) 2000 MIPS Technologies, Inc.
+ */
+#include <asm/irqflags.h>
+#include <asm/hazards.h>
+#include <linux/compiler.h>
+#include <linux/preempt.h>
+#include <linux/export.h>
+#include <linux/stringify.h>
+
+#if !defined(CONFIG_CPU_HAS_DIEI)
+
+/*
+ * For cli() we have to insert nops to make sure that the new value
+ * has actually arrived in the status register before the end of this
+ * macro.
+ * R4000/R4400 need three nops, the R4600 two nops and the R10000 needs
+ * no nops at all.
+ */
+/*
+ * For TX49, operating only IE bit is not enough.
+ *
+ * If mfc0 $12 follows store and the mfc0 is last instruction of a
+ * page and fetching the next instruction causes TLB miss, the result
+ * of the mfc0 might wrongly contain EXL bit.
+ *
+ * ERT-TX49H2-027, ERT-TX49H3-012, ERT-TX49HL3-006, ERT-TX49H4-008
+ *
+ * Workaround: mask EXL bit of the result or place a nop before mfc0.
+ */
+notrace void arch_local_irq_disable(void)
+{
+	preempt_disable_notrace();
+
+	__asm__ __volatile__(
+	"	.set	push						\n"
+	"	.set	noat						\n"
+	"	mfc0	$1,$12						\n"
+	"	ori	$1,0x1f						\n"
+	"	xori	$1,0x1f						\n"
+	"	.set	noreorder					\n"
+	"	mtc0	$1,$12						\n"
+	"	" __stringify(__irq_disable_hazard) "			\n"
+	"	.set	pop						\n"
+	: /* no outputs */
+	: /* no inputs */
+	: "memory");
+
+	preempt_enable_notrace();
+}
+EXPORT_SYMBOL(arch_local_irq_disable);
+
+notrace unsigned long arch_local_irq_save(void)
+{
+	unsigned long flags;
+
+	preempt_disable_notrace();
+
+	__asm__ __volatile__(
+	"	.set	push						\n"
+	"	.set	reorder						\n"
+	"	.set	noat						\n"
+	"	mfc0	%[flags], $12					\n"
+	"	ori	$1, %[flags], 0x1f				\n"
+	"	xori	$1, 0x1f					\n"
+	"	.set	noreorder					\n"
+	"	mtc0	$1, $12						\n"
+	"	" __stringify(__irq_disable_hazard) "			\n"
+	"	.set	pop						\n"
+	: [flags] "=r" (flags)
+	: /* no inputs */
+	: "memory");
+
+	preempt_enable_notrace();
+
+	return flags;
+}
+EXPORT_SYMBOL(arch_local_irq_save);
+
+notrace void arch_local_irq_restore(unsigned long flags)
+{
+	unsigned long __tmp1;
+
+	preempt_disable_notrace();
+
+	__asm__ __volatile__(
+	"	.set	push						\n"
+	"	.set	noreorder					\n"
+	"	.set	noat						\n"
+	"	mfc0	$1, $12						\n"
+	"	andi	%[flags], 1					\n"
+	"	ori	$1, 0x1f					\n"
+	"	xori	$1, 0x1f					\n"
+	"	or	%[flags], $1					\n"
+	"	mtc0	%[flags], $12					\n"
+	"	" __stringify(__irq_disable_hazard) "			\n"
+	"	.set	pop						\n"
+	: [flags] "=r" (__tmp1)
+	: "0" (flags)
+	: "memory");
+
+	preempt_enable_notrace();
+}
+EXPORT_SYMBOL(arch_local_irq_restore);
+
+#endif /* !CONFIG_CPU_HAS_DIEI */
diff --git a/arch/mips/lib/multi3.c b/arch/mips/lib/multi3.c
new file mode 100644
index 000000000..4c2483f41
--- /dev/null
+++ b/arch/mips/lib/multi3.c
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/export.h>
+
+#include "libgcc.h"
+
+/*
+ * GCC 7 & older can suboptimally generate __multi3 calls for mips64r6, so for
+ * that specific case only we implement that intrinsic here.
+ *
+ * See https://gcc.gnu.org/bugzilla/show_bug.cgi?id=82981
+ */
+#if defined(CONFIG_64BIT) && defined(CONFIG_CPU_MIPSR6) && (__GNUC__ < 8)
+
+/* multiply 64-bit values, low 64-bits returned */
+static inline long long notrace dmulu(long long a, long long b)
+{
+	long long res;
+
+	asm ("dmulu %0,%1,%2" : "=r" (res) : "r" (a), "r" (b));
+	return res;
+}
+
+/* multiply 64-bit unsigned values, high 64-bits of 128-bit result returned */
+static inline long long notrace dmuhu(long long a, long long b)
+{
+	long long res;
+
+	asm ("dmuhu %0,%1,%2" : "=r" (res) : "r" (a), "r" (b));
+	return res;
+}
+
+/* multiply 128-bit values, low 128-bits returned */
+ti_type notrace __multi3(ti_type a, ti_type b)
+{
+	TWunion res, aa, bb;
+
+	aa.ti = a;
+	bb.ti = b;
+
+	/*
+	 * a * b =           (a.lo * b.lo)
+	 *         + 2^64  * (a.hi * b.lo + a.lo * b.hi)
+	 *        [+ 2^128 * (a.hi * b.hi)]
+	 */
+	res.s.low = dmulu(aa.s.low, bb.s.low);
+	res.s.high = dmuhu(aa.s.low, bb.s.low);
+	res.s.high += dmulu(aa.s.high, bb.s.low);
+	res.s.high += dmulu(aa.s.low, bb.s.high);
+
+	return res.ti;
+}
+EXPORT_SYMBOL(__multi3);
+
+#endif /* 64BIT && CPU_MIPSR6 && GCC7 */
diff --git a/arch/mips/lib/r3k_dump_tlb.c b/arch/mips/lib/r3k_dump_tlb.c
new file mode 100644
index 000000000..fcf594af0
--- /dev/null
+++ b/arch/mips/lib/r3k_dump_tlb.c
@@ -0,0 +1,71 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Dump R3000 TLB for debugging purposes.
+ *
+ * Copyright (C) 1994, 1995 by Waldorf Electronics, written by Ralf Baechle.
+ * Copyright (C) 1999 by Silicon Graphics, Inc.
+ * Copyright (C) 1999 by Harald Koerfgen
+ */
+#include <linux/kernel.h>
+#include <linux/mm.h>
+
+#include <asm/mipsregs.h>
+#include <asm/mmu_context.h>
+#include <asm/page.h>
+#include <asm/tlbdebug.h>
+
+void dump_tlb_regs(void)
+{
+	pr_info("Index    : %0x\n", read_c0_index());
+	pr_info("EntryHi  : %0lx\n", read_c0_entryhi());
+	pr_info("EntryLo  : %0lx\n", read_c0_entrylo0());
+}
+
+static void dump_tlb(int first, int last)
+{
+	int	i;
+	unsigned int asid;
+	unsigned long entryhi, entrylo0, asid_mask;
+
+	asid_mask = cpu_asid_mask(&current_cpu_data);
+	asid = read_c0_entryhi() & asid_mask;
+
+	for (i = first; i <= last; i++) {
+		write_c0_index(i<<8);
+		__asm__ __volatile__(
+			".set\tnoreorder\n\t"
+			"tlbr\n\t"
+			"nop\n\t"
+			".set\treorder");
+		entryhi	 = read_c0_entryhi();
+		entrylo0 = read_c0_entrylo0();
+
+		/* Unused entries have a virtual address of KSEG0.  */
+		if ((entryhi & PAGE_MASK) != KSEG0 &&
+		    (entrylo0 & R3K_ENTRYLO_G ||
+		     (entryhi & asid_mask) == asid)) {
+			/*
+			 * Only print entries in use
+			 */
+			printk("Index: %2d ", i);
+
+			pr_cont("va=%08lx asid=%08lx"
+				"  [pa=%06lx n=%d d=%d v=%d g=%d]",
+				entryhi & PAGE_MASK,
+				entryhi & asid_mask,
+				entrylo0 & PAGE_MASK,
+				(entrylo0 & R3K_ENTRYLO_N) ? 1 : 0,
+				(entrylo0 & R3K_ENTRYLO_D) ? 1 : 0,
+				(entrylo0 & R3K_ENTRYLO_V) ? 1 : 0,
+				(entrylo0 & R3K_ENTRYLO_G) ? 1 : 0);
+		}
+	}
+	printk("\n");
+
+	write_c0_entryhi(asid);
+}
+
+void dump_tlb_all(void)
+{
+	dump_tlb(0, current_cpu_data.tlbsize - 1);
+}
diff --git a/arch/mips/lib/strncpy_user.S b/arch/mips/lib/strncpy_user.S
new file mode 100644
index 000000000..13aaa9927
--- /dev/null
+++ b/arch/mips/lib/strncpy_user.S
@@ -0,0 +1,65 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1996, 1999 by Ralf Baechle
+ * Copyright (C) 2011 MIPS Technologies, Inc.
+ */
+#include <linux/errno.h>
+#include <asm/asm.h>
+#include <asm/asm-offsets.h>
+#include <asm/export.h>
+#include <asm/regdef.h>
+
+#define EX(insn,reg,addr,handler)			\
+9:	insn	reg, addr;				\
+	.section __ex_table,"a";			\
+	PTR_WD	9b, handler;				\
+	.previous
+
+/*
+ * Returns: -EFAULT if exception before terminator, N if the entire
+ * buffer filled, else strlen.
+ */
+
+/*
+ * Ugly special case have to check: we might get passed a user space
+ * pointer which wraps into the kernel space.  We don't deal with that.	 If
+ * it happens at most some bytes of the exceptions handlers will be copied.
+ */
+
+LEAF(__strncpy_from_user_asm)
+	move		t0, zero
+	move		v1, a1
+#ifdef CONFIG_EVA
+	.set push
+	.set eva
+1:	EX(lbue, v0, (v1), .Lfault)
+	.set pop
+#else
+1:	EX(lbu, v0, (v1), .Lfault)
+#endif
+	PTR_ADDIU	v1, 1
+	R10KCBARRIER(0(ra))
+	sb		v0, (a0)
+	beqz		v0, 2f
+	PTR_ADDIU	t0, 1
+	PTR_ADDIU	a0, 1
+	bne		t0, a2, 1b
+2:	PTR_ADDU	v0, a1, t0
+	xor		v0, a1
+	bltz		v0, .Lfault
+	move		v0, t0
+	jr		ra			# return n
+	END(__strncpy_from_user_asm)
+
+.Lfault:
+	li		v0, -EFAULT
+	jr		ra
+
+	.section	__ex_table,"a"
+	PTR_WD		1b, .Lfault
+	.previous
+
+	EXPORT_SYMBOL(__strncpy_from_user_asm)
diff --git a/arch/mips/lib/strnlen_user.S b/arch/mips/lib/strnlen_user.S
new file mode 100644
index 000000000..6de31b616
--- /dev/null
+++ b/arch/mips/lib/strnlen_user.S
@@ -0,0 +1,64 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (c) 1996, 1998, 1999, 2004 by Ralf Baechle
+ * Copyright (c) 1999 Silicon Graphics, Inc.
+ */
+#include <asm/asm.h>
+#include <asm/asm-offsets.h>
+#include <asm/export.h>
+#include <asm/regdef.h>
+
+#define EX(insn,reg,addr,handler)			\
+9:	insn	reg, addr;				\
+	.section __ex_table,"a";			\
+	PTR_WD	9b, handler;				\
+	.previous
+
+/*
+ * Return the size of a string including the ending NUL character up to a
+ * maximum of a1 or 0 in case of error.
+ *
+ * Note: for performance reasons we deliberately accept that a user may
+ *	 make strlen_user and strnlen_user access the first few KSEG0
+ *	 bytes.	 There's nothing secret there.	On 64-bit accessing beyond
+ *	 the maximum is a tad hairier ...
+ */
+LEAF(__strnlen_user_asm)
+	move		v0, a0
+	PTR_ADDU	a1, a0			# stop pointer
+1:
+#ifdef CONFIG_CPU_DADDI_WORKAROUNDS
+	.set		noat
+	li		AT, 1
+#endif
+	beq		v0, a1, 1f		# limit reached?
+#ifdef CONFIG_EVA
+	.set push
+	.set eva
+	EX(lbe, t0, (v0), .Lfault)
+	.set pop
+#else
+	EX(lb, t0, (v0), .Lfault)
+#endif
+	.set		noreorder
+	bnez		t0, 1b
+1:
+#ifndef CONFIG_CPU_DADDI_WORKAROUNDS
+	 PTR_ADDIU	v0, 1
+#else
+	 PTR_ADDU	v0, AT
+	.set		at
+#endif
+	.set		reorder
+	PTR_SUBU	v0, a0
+	jr		ra
+	END(__strnlen_user_asm)
+
+.Lfault:
+	move		v0, zero
+	jr		ra
+
+	EXPORT_SYMBOL(__strnlen_user_asm)
diff --git a/arch/mips/lib/uncached.c b/arch/mips/lib/uncached.c
new file mode 100644
index 000000000..f80a67c09
--- /dev/null
+++ b/arch/mips/lib/uncached.c
@@ -0,0 +1,82 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2005 Thiemo Seufer
+ * Copyright (C) 2005  MIPS Technologies, Inc.	All rights reserved.
+ *	Author: Maciej W. Rozycki <macro@mips.com>
+ */
+
+
+#include <asm/addrspace.h>
+#include <asm/bug.h>
+#include <asm/cacheflush.h>
+
+#ifndef CKSEG2
+#define CKSEG2 CKSSEG
+#endif
+#ifndef TO_PHYS_MASK
+#define TO_PHYS_MASK -1
+#endif
+
+/*
+ * FUNC is executed in one of the uncached segments, depending on its
+ * original address as follows:
+ *
+ * 1. If the original address is in CKSEG0 or CKSEG1, then the uncached
+ *    segment used is CKSEG1.
+ * 2. If the original address is in XKPHYS, then the uncached segment
+ *    used is XKPHYS(2).
+ * 3. Otherwise it's a bug.
+ *
+ * The same remapping is done with the stack pointer.  Stack handling
+ * works because we don't handle stack arguments or more complex return
+ * values, so we can avoid sharing the same stack area between a cached
+ * and the uncached mode.
+ */
+unsigned long run_uncached(void *func)
+{
+	register long ret __asm__("$2");
+	long lfunc = (long)func, ufunc;
+	long usp;
+	long sp;
+
+	__asm__("move %0, $sp" : "=r" (sp));
+
+	if (sp >= (long)CKSEG0 && sp < (long)CKSEG2)
+		usp = CKSEG1ADDR(sp);
+#ifdef CONFIG_64BIT
+	else if ((long long)sp >= (long long)PHYS_TO_XKPHYS(0, 0) &&
+		 (long long)sp < (long long)PHYS_TO_XKPHYS(8, 0))
+		usp = PHYS_TO_XKPHYS(K_CALG_UNCACHED,
+				     XKPHYS_TO_PHYS((long long)sp));
+#endif
+	else {
+		BUG();
+		usp = sp;
+	}
+	if (lfunc >= (long)CKSEG0 && lfunc < (long)CKSEG2)
+		ufunc = CKSEG1ADDR(lfunc);
+#ifdef CONFIG_64BIT
+	else if ((long long)lfunc >= (long long)PHYS_TO_XKPHYS(0, 0) &&
+		 (long long)lfunc < (long long)PHYS_TO_XKPHYS(8, 0))
+		ufunc = PHYS_TO_XKPHYS(K_CALG_UNCACHED,
+				       XKPHYS_TO_PHYS((long long)lfunc));
+#endif
+	else {
+		BUG();
+		ufunc = lfunc;
+	}
+
+	__asm__ __volatile__ (
+		"	move	$16, $sp\n"
+		"	move	$sp, %1\n"
+		"	jalr	%2\n"
+		"	move	$sp, $16"
+		: "=r" (ret)
+		: "r" (usp), "r" (ufunc)
+		: "$16", "$31");
+
+	return ret;
+}
diff --git a/arch/mips/loongson2ef/Kconfig b/arch/mips/loongson2ef/Kconfig
new file mode 100644
index 000000000..96dc6eba4
--- /dev/null
+++ b/arch/mips/loongson2ef/Kconfig
@@ -0,0 +1,94 @@
+# SPDX-License-Identifier: GPL-2.0
+if MACH_LOONGSON2EF
+
+choice
+	prompt "Machine Type"
+
+config LEMOTE_FULOONG2E
+	bool "Lemote Fuloong(2e) mini-PC"
+	select ARCH_SPARSEMEM_ENABLE
+	select ARCH_MIGHT_HAVE_PC_PARPORT
+	select ARCH_MIGHT_HAVE_PC_SERIO
+	select CEVT_R4K
+	select CSRC_R4K
+	select SYS_HAS_CPU_LOONGSON2E
+	select DMA_NONCOHERENT
+	select BOOT_ELF32
+	select BOARD_SCACHE
+	select FORCE_PCI
+	select I8259
+	select ISA
+	select IRQ_MIPS_CPU
+	select SYS_SUPPORTS_64BIT_KERNEL
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_SUPPORTS_HIGHMEM
+	select SYS_HAS_EARLY_PRINTK
+	select USE_GENERIC_EARLY_PRINTK_8250
+	select GENERIC_ISA_DMA_SUPPORT_BROKEN
+	select CPU_HAS_WB
+	select LOONGSON_MC146818
+	help
+	  Lemote Fuloong(2e) mini-PC board based on the Chinese Loongson-2E CPU and
+	  an FPGA northbridge
+
+	  Lemote Fuloong(2e) mini PC have a VIA686B south bridge.
+
+config LEMOTE_MACH2F
+	bool "Lemote Loongson 2F family machines"
+	select ARCH_SPARSEMEM_ENABLE
+	select ARCH_MIGHT_HAVE_PC_PARPORT
+	select ARCH_MIGHT_HAVE_PC_SERIO
+	select BOARD_SCACHE
+	select BOOT_ELF32
+	select CEVT_R4K if ! MIPS_EXTERNAL_TIMER
+	select CPU_HAS_WB
+	select CS5536
+	select CSRC_R4K if ! MIPS_EXTERNAL_TIMER
+	select DMA_NONCOHERENT
+	select GENERIC_ISA_DMA_SUPPORT_BROKEN
+	select FORCE_PCI
+	select I8259
+	select IRQ_MIPS_CPU
+	select ISA
+	select SYS_HAS_CPU_LOONGSON2F
+	select SYS_HAS_EARLY_PRINTK
+	select USE_GENERIC_EARLY_PRINTK_8250
+	select SYS_SUPPORTS_64BIT_KERNEL
+	select SYS_SUPPORTS_HIGHMEM
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select LOONGSON_MC146818
+	help
+	  Lemote Loongson 2F family machines utilize the 2F revision of
+	  Loongson processor and the AMD CS5536 south bridge.
+
+	  These family machines include fuloong2f mini PC, yeeloong2f notebook,
+	  LingLoong allinone PC and so forth.
+
+endchoice
+
+config CS5536
+	bool
+
+config CS5536_MFGPT
+	bool "CS5536 MFGPT Timer"
+	depends on CS5536 && !HIGH_RES_TIMERS
+	select MIPS_EXTERNAL_TIMER
+	help
+	  This option enables the mfgpt0 timer of AMD CS5536. With this timer
+	  switched on you can not use high resolution timers.
+
+	  If you want to enable the Loongson2 CPUFreq Driver, Please enable
+	  this option at first, otherwise, You will get wrong system time.
+
+	  If unsure, say Yes.
+
+config LOONGSON_UART_BASE
+	bool
+	default y
+	depends on EARLY_PRINTK || SERIAL_8250
+
+config LOONGSON_MC146818
+	bool
+	default n
+
+endif # MACH_LOONGSON2EF
diff --git a/arch/mips/loongson2ef/Makefile b/arch/mips/loongson2ef/Makefile
new file mode 100644
index 000000000..d4af1605c
--- /dev/null
+++ b/arch/mips/loongson2ef/Makefile
@@ -0,0 +1,18 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Common code for all Loongson based systems
+#
+
+obj-$(CONFIG_MACH_LOONGSON2EF) += common/
+
+#
+# Lemote Fuloong mini-PC (Loongson 2E-based)
+#
+
+obj-$(CONFIG_LEMOTE_FULOONG2E)	+= fuloong-2e/
+
+#
+# Lemote loongson2f family machines
+#
+
+obj-$(CONFIG_LEMOTE_MACH2F)  += lemote-2f/
diff --git a/arch/mips/loongson2ef/Platform b/arch/mips/loongson2ef/Platform
new file mode 100644
index 000000000..d446b705f
--- /dev/null
+++ b/arch/mips/loongson2ef/Platform
@@ -0,0 +1,12 @@
+#
+# Loongson Processors' Support
+#
+
+#
+# Loongson Machines' Support
+#
+
+cflags-$(CONFIG_MACH_LOONGSON2EF) += -I$(srctree)/arch/mips/include/asm/mach-loongson2ef
+cflags-$(CONFIG_CC_HAS_MNO_BRANCH_LIKELY) += -mno-branch-likely
+load-$(CONFIG_LEMOTE_FULOONG2E) += 0xffffffff80100000
+load-$(CONFIG_LEMOTE_MACH2F) += 0xffffffff80200000
diff --git a/arch/mips/loongson2ef/common/Makefile b/arch/mips/loongson2ef/common/Makefile
new file mode 100644
index 000000000..30ea8b5ca
--- /dev/null
+++ b/arch/mips/loongson2ef/common/Makefile
@@ -0,0 +1,28 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Makefile for loongson based machines.
+#
+
+obj-y += setup.o init.o env.o time.o reset.o irq.o \
+    bonito-irq.o mem.o machtype.o platform.o
+obj-$(CONFIG_PCI) += pci.o
+
+#
+# Serial port support
+#
+obj-$(CONFIG_LOONGSON_UART_BASE) += serial.o
+obj-$(CONFIG_EARLY_PRINTK) += serial.o
+obj-$(CONFIG_LOONGSON_UART_BASE) += uart_base.o
+obj-$(CONFIG_LOONGSON_MC146818) += rtc.o
+
+#
+# Enable CS5536 Virtual Support Module(VSM) to virtulize the PCI configure
+# space
+#
+obj-$(CONFIG_CS5536) += cs5536/
+
+#
+# Suspend Support
+#
+
+obj-$(CONFIG_SUSPEND) += pm.o
diff --git a/arch/mips/loongson2ef/common/bonito-irq.c b/arch/mips/loongson2ef/common/bonito-irq.c
new file mode 100644
index 000000000..c06ad412e
--- /dev/null
+++ b/arch/mips/loongson2ef/common/bonito-irq.c
@@ -0,0 +1,46 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2001 MontaVista Software Inc.
+ * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net
+ * Copyright (C) 2000, 2001 Ralf Baechle (ralf@gnu.org)
+ *
+ * Copyright (C) 2007 Lemote Inc. & Institute of Computing Technology
+ * Author: Fuxin Zhang, zhangfx@lemote.com
+ */
+#include <linux/interrupt.h>
+#include <linux/compiler.h>
+
+#include <loongson.h>
+
+static inline void bonito_irq_enable(struct irq_data *d)
+{
+	LOONGSON_INTENSET = (1 << (d->irq - LOONGSON_IRQ_BASE));
+	mmiowb();
+}
+
+static inline void bonito_irq_disable(struct irq_data *d)
+{
+	LOONGSON_INTENCLR = (1 << (d->irq - LOONGSON_IRQ_BASE));
+	mmiowb();
+}
+
+static struct irq_chip bonito_irq_type = {
+	.name		= "bonito_irq",
+	.irq_mask	= bonito_irq_disable,
+	.irq_unmask	= bonito_irq_enable,
+};
+
+void bonito_irq_init(void)
+{
+	u32 i;
+
+	for (i = LOONGSON_IRQ_BASE; i < LOONGSON_IRQ_BASE + 32; i++)
+		irq_set_chip_and_handler(i, &bonito_irq_type,
+					 handle_level_irq);
+
+#ifdef CONFIG_CPU_LOONGSON2E
+	i = LOONGSON_IRQ_BASE + 10;
+	if (request_irq(i, no_action, 0, "dma_timeout", NULL))
+		pr_err("Failed to request irq %d (dma_timeout)\n", i);
+#endif
+}
diff --git a/arch/mips/loongson2ef/common/cs5536/Makefile b/arch/mips/loongson2ef/common/cs5536/Makefile
new file mode 100644
index 000000000..b32b29661
--- /dev/null
+++ b/arch/mips/loongson2ef/common/cs5536/Makefile
@@ -0,0 +1,12 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Makefile for CS5536 support.
+#
+
+obj-$(CONFIG_CS5536) += cs5536_pci.o cs5536_ide.o cs5536_acc.o cs5536_ohci.o \
+			cs5536_isa.o cs5536_ehci.o
+
+#
+# Enable cs5536 mfgpt Timer
+#
+obj-$(CONFIG_CS5536_MFGPT) += cs5536_mfgpt.o
diff --git a/arch/mips/loongson2ef/common/cs5536/cs5536_acc.c b/arch/mips/loongson2ef/common/cs5536/cs5536_acc.c
new file mode 100644
index 000000000..ff50aae72
--- /dev/null
+++ b/arch/mips/loongson2ef/common/cs5536/cs5536_acc.c
@@ -0,0 +1,136 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * the ACC Virtual Support Module of AMD CS5536
+ *
+ * Copyright (C) 2007 Lemote, Inc.
+ * Author : jlliu, liujl@lemote.com
+ *
+ * Copyright (C) 2009 Lemote, Inc.
+ * Author: Wu Zhangjin, wuzhangjin@gmail.com
+ */
+
+#include <cs5536/cs5536.h>
+#include <cs5536/cs5536_pci.h>
+
+void pci_acc_write_reg(int reg, u32 value)
+{
+	u32 hi = 0, lo = value;
+
+	switch (reg) {
+	case PCI_COMMAND:
+		_rdmsr(GLIU_MSR_REG(GLIU_PAE), &hi, &lo);
+		if (value & PCI_COMMAND_MASTER)
+			lo |= (0x03 << 8);
+		else
+			lo &= ~(0x03 << 8);
+		_wrmsr(GLIU_MSR_REG(GLIU_PAE), hi, lo);
+		break;
+	case PCI_STATUS:
+		if (value & PCI_STATUS_PARITY) {
+			_rdmsr(SB_MSR_REG(SB_ERROR), &hi, &lo);
+			if (lo & SB_PARE_ERR_FLAG) {
+				lo = (lo & 0x0000ffff) | SB_PARE_ERR_FLAG;
+				_wrmsr(SB_MSR_REG(SB_ERROR), hi, lo);
+			}
+		}
+		break;
+	case PCI_BAR0_REG:
+		if (value == PCI_BAR_RANGE_MASK) {
+			_rdmsr(GLCP_MSR_REG(GLCP_SOFT_COM), &hi, &lo);
+			lo |= SOFT_BAR_ACC_FLAG;
+			_wrmsr(GLCP_MSR_REG(GLCP_SOFT_COM), hi, lo);
+		} else if (value & 0x01) {
+			value &= 0xfffffffc;
+			hi = 0xA0000000 | ((value & 0x000ff000) >> 12);
+			lo = 0x000fff80 | ((value & 0x00000fff) << 20);
+			_wrmsr(GLIU_MSR_REG(GLIU_IOD_BM1), hi, lo);
+		}
+		break;
+	case PCI_ACC_INT_REG:
+		_rdmsr(DIVIL_MSR_REG(PIC_YSEL_LOW), &hi, &lo);
+		/* disable all the usb interrupt in PIC */
+		lo &= ~(0xf << PIC_YSEL_LOW_ACC_SHIFT);
+		if (value)	/* enable all the acc interrupt in PIC */
+			lo |= (CS5536_ACC_INTR << PIC_YSEL_LOW_ACC_SHIFT);
+		_wrmsr(DIVIL_MSR_REG(PIC_YSEL_LOW), hi, lo);
+		break;
+	default:
+		break;
+	}
+}
+
+u32 pci_acc_read_reg(int reg)
+{
+	u32 hi, lo;
+	u32 conf_data = 0;
+
+	switch (reg) {
+	case PCI_VENDOR_ID:
+		conf_data =
+		    CFG_PCI_VENDOR_ID(CS5536_ACC_DEVICE_ID, CS5536_VENDOR_ID);
+		break;
+	case PCI_COMMAND:
+		_rdmsr(GLIU_MSR_REG(GLIU_IOD_BM1), &hi, &lo);
+		if (((lo & 0xfff00000) || (hi & 0x000000ff))
+		    && ((hi & 0xf0000000) == 0xa0000000))
+			conf_data |= PCI_COMMAND_IO;
+		_rdmsr(GLIU_MSR_REG(GLIU_PAE), &hi, &lo);
+		if ((lo & 0x300) == 0x300)
+			conf_data |= PCI_COMMAND_MASTER;
+		break;
+	case PCI_STATUS:
+		conf_data |= PCI_STATUS_66MHZ;
+		conf_data |= PCI_STATUS_FAST_BACK;
+		_rdmsr(SB_MSR_REG(SB_ERROR), &hi, &lo);
+		if (lo & SB_PARE_ERR_FLAG)
+			conf_data |= PCI_STATUS_PARITY;
+		conf_data |= PCI_STATUS_DEVSEL_MEDIUM;
+		break;
+	case PCI_CLASS_REVISION:
+		_rdmsr(ACC_MSR_REG(ACC_CAP), &hi, &lo);
+		conf_data = lo & 0x000000ff;
+		conf_data |= (CS5536_ACC_CLASS_CODE << 8);
+		break;
+	case PCI_CACHE_LINE_SIZE:
+		conf_data =
+		    CFG_PCI_CACHE_LINE_SIZE(PCI_NORMAL_HEADER_TYPE,
+					    PCI_NORMAL_LATENCY_TIMER);
+		break;
+	case PCI_BAR0_REG:
+		_rdmsr(GLCP_MSR_REG(GLCP_SOFT_COM), &hi, &lo);
+		if (lo & SOFT_BAR_ACC_FLAG) {
+			conf_data = CS5536_ACC_RANGE |
+			    PCI_BASE_ADDRESS_SPACE_IO;
+			lo &= ~SOFT_BAR_ACC_FLAG;
+			_wrmsr(GLCP_MSR_REG(GLCP_SOFT_COM), hi, lo);
+		} else {
+			_rdmsr(GLIU_MSR_REG(GLIU_IOD_BM1), &hi, &lo);
+			conf_data = (hi & 0x000000ff) << 12;
+			conf_data |= (lo & 0xfff00000) >> 20;
+			conf_data |= 0x01;
+			conf_data &= ~0x02;
+		}
+		break;
+	case PCI_CARDBUS_CIS:
+		conf_data = PCI_CARDBUS_CIS_POINTER;
+		break;
+	case PCI_SUBSYSTEM_VENDOR_ID:
+		conf_data =
+		    CFG_PCI_VENDOR_ID(CS5536_ACC_SUB_ID, CS5536_SUB_VENDOR_ID);
+		break;
+	case PCI_ROM_ADDRESS:
+		conf_data = PCI_EXPANSION_ROM_BAR;
+		break;
+	case PCI_CAPABILITY_LIST:
+		conf_data = PCI_CAPLIST_USB_POINTER;
+		break;
+	case PCI_INTERRUPT_LINE:
+		conf_data =
+		    CFG_PCI_INTERRUPT_LINE(PCI_DEFAULT_PIN, CS5536_ACC_INTR);
+		break;
+	default:
+		break;
+	}
+
+	return conf_data;
+}
diff --git a/arch/mips/loongson2ef/common/cs5536/cs5536_ehci.c b/arch/mips/loongson2ef/common/cs5536/cs5536_ehci.c
new file mode 100644
index 000000000..bd4c39fe6
--- /dev/null
+++ b/arch/mips/loongson2ef/common/cs5536/cs5536_ehci.c
@@ -0,0 +1,156 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * the EHCI Virtual Support Module of AMD CS5536
+ *
+ * Copyright (C) 2007 Lemote, Inc.
+ * Author : jlliu, liujl@lemote.com
+ *
+ * Copyright (C) 2009 Lemote, Inc.
+ * Author: Wu Zhangjin, wuzhangjin@gmail.com
+ */
+
+#include <cs5536/cs5536.h>
+#include <cs5536/cs5536_pci.h>
+
+void pci_ehci_write_reg(int reg, u32 value)
+{
+	u32 hi = 0, lo = value;
+
+	switch (reg) {
+	case PCI_COMMAND:
+		_rdmsr(USB_MSR_REG(USB_EHCI), &hi, &lo);
+		if (value & PCI_COMMAND_MASTER)
+			hi |= PCI_COMMAND_MASTER;
+		else
+			hi &= ~PCI_COMMAND_MASTER;
+
+		if (value & PCI_COMMAND_MEMORY)
+			hi |= PCI_COMMAND_MEMORY;
+		else
+			hi &= ~PCI_COMMAND_MEMORY;
+		_wrmsr(USB_MSR_REG(USB_EHCI), hi, lo);
+		break;
+	case PCI_STATUS:
+		if (value & PCI_STATUS_PARITY) {
+			_rdmsr(SB_MSR_REG(SB_ERROR), &hi, &lo);
+			if (lo & SB_PARE_ERR_FLAG) {
+				lo = (lo & 0x0000ffff) | SB_PARE_ERR_FLAG;
+				_wrmsr(SB_MSR_REG(SB_ERROR), hi, lo);
+			}
+		}
+		break;
+	case PCI_BAR0_REG:
+		if (value == PCI_BAR_RANGE_MASK) {
+			_rdmsr(GLCP_MSR_REG(GLCP_SOFT_COM), &hi, &lo);
+			lo |= SOFT_BAR_EHCI_FLAG;
+			_wrmsr(GLCP_MSR_REG(GLCP_SOFT_COM), hi, lo);
+		} else if ((value & 0x01) == 0x00) {
+			_rdmsr(USB_MSR_REG(USB_EHCI), &hi, &lo);
+			lo = value;
+			_wrmsr(USB_MSR_REG(USB_EHCI), hi, lo);
+
+			value &= 0xfffffff0;
+			hi = 0x40000000 | ((value & 0xff000000) >> 24);
+			lo = 0x000fffff | ((value & 0x00fff000) << 8);
+			_wrmsr(GLIU_MSR_REG(GLIU_P2D_BM4), hi, lo);
+		}
+		break;
+	case PCI_EHCI_LEGSMIEN_REG:
+		_rdmsr(USB_MSR_REG(USB_EHCI), &hi, &lo);
+		hi &= 0x003f0000;
+		hi |= (value & 0x3f) << 16;
+		_wrmsr(USB_MSR_REG(USB_EHCI), hi, lo);
+		break;
+	case PCI_EHCI_FLADJ_REG:
+		_rdmsr(USB_MSR_REG(USB_EHCI), &hi, &lo);
+		hi &= ~0x00003f00;
+		hi |= value & 0x00003f00;
+		_wrmsr(USB_MSR_REG(USB_EHCI), hi, lo);
+		break;
+	default:
+		break;
+	}
+}
+
+u32 pci_ehci_read_reg(int reg)
+{
+	u32 conf_data = 0;
+	u32 hi, lo;
+
+	switch (reg) {
+	case PCI_VENDOR_ID:
+		conf_data =
+		    CFG_PCI_VENDOR_ID(CS5536_EHCI_DEVICE_ID, CS5536_VENDOR_ID);
+		break;
+	case PCI_COMMAND:
+		_rdmsr(USB_MSR_REG(USB_EHCI), &hi, &lo);
+		if (hi & PCI_COMMAND_MASTER)
+			conf_data |= PCI_COMMAND_MASTER;
+		if (hi & PCI_COMMAND_MEMORY)
+			conf_data |= PCI_COMMAND_MEMORY;
+		break;
+	case PCI_STATUS:
+		conf_data |= PCI_STATUS_66MHZ;
+		conf_data |= PCI_STATUS_FAST_BACK;
+		_rdmsr(SB_MSR_REG(SB_ERROR), &hi, &lo);
+		if (lo & SB_PARE_ERR_FLAG)
+			conf_data |= PCI_STATUS_PARITY;
+		conf_data |= PCI_STATUS_DEVSEL_MEDIUM;
+		break;
+	case PCI_CLASS_REVISION:
+		_rdmsr(USB_MSR_REG(USB_CAP), &hi, &lo);
+		conf_data = lo & 0x000000ff;
+		conf_data |= (CS5536_EHCI_CLASS_CODE << 8);
+		break;
+	case PCI_CACHE_LINE_SIZE:
+		conf_data =
+		    CFG_PCI_CACHE_LINE_SIZE(PCI_NORMAL_HEADER_TYPE,
+					    PCI_NORMAL_LATENCY_TIMER);
+		break;
+	case PCI_BAR0_REG:
+		_rdmsr(GLCP_MSR_REG(GLCP_SOFT_COM), &hi, &lo);
+		if (lo & SOFT_BAR_EHCI_FLAG) {
+			conf_data = CS5536_EHCI_RANGE |
+			    PCI_BASE_ADDRESS_SPACE_MEMORY;
+			lo &= ~SOFT_BAR_EHCI_FLAG;
+			_wrmsr(GLCP_MSR_REG(GLCP_SOFT_COM), hi, lo);
+		} else {
+			_rdmsr(USB_MSR_REG(USB_EHCI), &hi, &lo);
+			conf_data = lo & 0xfffff000;
+		}
+		break;
+	case PCI_CARDBUS_CIS:
+		conf_data = PCI_CARDBUS_CIS_POINTER;
+		break;
+	case PCI_SUBSYSTEM_VENDOR_ID:
+		conf_data =
+		    CFG_PCI_VENDOR_ID(CS5536_EHCI_SUB_ID, CS5536_SUB_VENDOR_ID);
+		break;
+	case PCI_ROM_ADDRESS:
+		conf_data = PCI_EXPANSION_ROM_BAR;
+		break;
+	case PCI_CAPABILITY_LIST:
+		conf_data = PCI_CAPLIST_USB_POINTER;
+		break;
+	case PCI_INTERRUPT_LINE:
+		conf_data =
+		    CFG_PCI_INTERRUPT_LINE(PCI_DEFAULT_PIN, CS5536_USB_INTR);
+		break;
+	case PCI_EHCI_LEGSMIEN_REG:
+		_rdmsr(USB_MSR_REG(USB_EHCI), &hi, &lo);
+		conf_data = (hi & 0x003f0000) >> 16;
+		break;
+	case PCI_EHCI_LEGSMISTS_REG:
+		_rdmsr(USB_MSR_REG(USB_EHCI), &hi, &lo);
+		conf_data = (hi & 0x3f000000) >> 24;
+		break;
+	case PCI_EHCI_FLADJ_REG:
+		_rdmsr(USB_MSR_REG(USB_EHCI), &hi, &lo);
+		conf_data = hi & 0x00003f00;
+		break;
+	default:
+		break;
+	}
+
+	return conf_data;
+}
diff --git a/arch/mips/loongson2ef/common/cs5536/cs5536_ide.c b/arch/mips/loongson2ef/common/cs5536/cs5536_ide.c
new file mode 100644
index 000000000..bb933294b
--- /dev/null
+++ b/arch/mips/loongson2ef/common/cs5536/cs5536_ide.c
@@ -0,0 +1,188 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * the IDE Virtual Support Module of AMD CS5536
+ *
+ * Copyright (C) 2007 Lemote, Inc.
+ * Author : jlliu, liujl@lemote.com
+ *
+ * Copyright (C) 2009 Lemote, Inc.
+ * Author: Wu Zhangjin, wuzhangjin@gmail.com
+ */
+
+#include <cs5536/cs5536.h>
+#include <cs5536/cs5536_pci.h>
+
+void pci_ide_write_reg(int reg, u32 value)
+{
+	u32 hi = 0, lo = value;
+
+	switch (reg) {
+	case PCI_COMMAND:
+		_rdmsr(GLIU_MSR_REG(GLIU_PAE), &hi, &lo);
+		if (value & PCI_COMMAND_MASTER)
+			lo |= (0x03 << 4);
+		else
+			lo &= ~(0x03 << 4);
+		_wrmsr(GLIU_MSR_REG(GLIU_PAE), hi, lo);
+		break;
+	case PCI_STATUS:
+		if (value & PCI_STATUS_PARITY) {
+			_rdmsr(SB_MSR_REG(SB_ERROR), &hi, &lo);
+			if (lo & SB_PARE_ERR_FLAG) {
+				lo = (lo & 0x0000ffff) | SB_PARE_ERR_FLAG;
+				_wrmsr(SB_MSR_REG(SB_ERROR), hi, lo);
+			}
+		}
+		break;
+	case PCI_CACHE_LINE_SIZE:
+		value &= 0x0000ff00;
+		_rdmsr(SB_MSR_REG(SB_CTRL), &hi, &lo);
+		hi &= 0xffffff00;
+		hi |= (value >> 8);
+		_wrmsr(SB_MSR_REG(SB_CTRL), hi, lo);
+		break;
+	case PCI_BAR4_REG:
+		if (value == PCI_BAR_RANGE_MASK) {
+			_rdmsr(GLCP_MSR_REG(GLCP_SOFT_COM), &hi, &lo);
+			lo |= SOFT_BAR_IDE_FLAG;
+			_wrmsr(GLCP_MSR_REG(GLCP_SOFT_COM), hi, lo);
+		} else if (value & 0x01) {
+			_rdmsr(IDE_MSR_REG(IDE_IO_BAR), &hi, &lo);
+			lo = (value & 0xfffffff0) | 0x1;
+			_wrmsr(IDE_MSR_REG(IDE_IO_BAR), hi, lo);
+
+			value &= 0xfffffffc;
+			hi = 0x60000000 | ((value & 0x000ff000) >> 12);
+			lo = 0x000ffff0 | ((value & 0x00000fff) << 20);
+			_wrmsr(GLIU_MSR_REG(GLIU_IOD_BM2), hi, lo);
+		}
+		break;
+	case PCI_IDE_CFG_REG:
+		if (value == CS5536_IDE_FLASH_SIGNATURE) {
+			_rdmsr(DIVIL_MSR_REG(DIVIL_BALL_OPTS), &hi, &lo);
+			lo |= 0x01;
+			_wrmsr(DIVIL_MSR_REG(DIVIL_BALL_OPTS), hi, lo);
+		} else {
+			_rdmsr(IDE_MSR_REG(IDE_CFG), &hi, &lo);
+			lo = value;
+			_wrmsr(IDE_MSR_REG(IDE_CFG), hi, lo);
+		}
+		break;
+	case PCI_IDE_DTC_REG:
+		_rdmsr(IDE_MSR_REG(IDE_DTC), &hi, &lo);
+		lo = value;
+		_wrmsr(IDE_MSR_REG(IDE_DTC), hi, lo);
+		break;
+	case PCI_IDE_CAST_REG:
+		_rdmsr(IDE_MSR_REG(IDE_CAST), &hi, &lo);
+		lo = value;
+		_wrmsr(IDE_MSR_REG(IDE_CAST), hi, lo);
+		break;
+	case PCI_IDE_ETC_REG:
+		_rdmsr(IDE_MSR_REG(IDE_ETC), &hi, &lo);
+		lo = value;
+		_wrmsr(IDE_MSR_REG(IDE_ETC), hi, lo);
+		break;
+	case PCI_IDE_PM_REG:
+		_rdmsr(IDE_MSR_REG(IDE_INTERNAL_PM), &hi, &lo);
+		lo = value;
+		_wrmsr(IDE_MSR_REG(IDE_INTERNAL_PM), hi, lo);
+		break;
+	default:
+		break;
+	}
+}
+
+u32 pci_ide_read_reg(int reg)
+{
+	u32 conf_data = 0;
+	u32 hi, lo;
+
+	switch (reg) {
+	case PCI_VENDOR_ID:
+		conf_data =
+		    CFG_PCI_VENDOR_ID(CS5536_IDE_DEVICE_ID, CS5536_VENDOR_ID);
+		break;
+	case PCI_COMMAND:
+		_rdmsr(IDE_MSR_REG(IDE_IO_BAR), &hi, &lo);
+		if (lo & 0xfffffff0)
+			conf_data |= PCI_COMMAND_IO;
+		_rdmsr(GLIU_MSR_REG(GLIU_PAE), &hi, &lo);
+		if ((lo & 0x30) == 0x30)
+			conf_data |= PCI_COMMAND_MASTER;
+		break;
+	case PCI_STATUS:
+		conf_data |= PCI_STATUS_66MHZ;
+		conf_data |= PCI_STATUS_FAST_BACK;
+		_rdmsr(SB_MSR_REG(SB_ERROR), &hi, &lo);
+		if (lo & SB_PARE_ERR_FLAG)
+			conf_data |= PCI_STATUS_PARITY;
+		conf_data |= PCI_STATUS_DEVSEL_MEDIUM;
+		break;
+	case PCI_CLASS_REVISION:
+		_rdmsr(IDE_MSR_REG(IDE_CAP), &hi, &lo);
+		conf_data = lo & 0x000000ff;
+		conf_data |= (CS5536_IDE_CLASS_CODE << 8);
+		break;
+	case PCI_CACHE_LINE_SIZE:
+		_rdmsr(SB_MSR_REG(SB_CTRL), &hi, &lo);
+		hi &= 0x000000f8;
+		conf_data = CFG_PCI_CACHE_LINE_SIZE(PCI_NORMAL_HEADER_TYPE, hi);
+		break;
+	case PCI_BAR4_REG:
+		_rdmsr(GLCP_MSR_REG(GLCP_SOFT_COM), &hi, &lo);
+		if (lo & SOFT_BAR_IDE_FLAG) {
+			conf_data = CS5536_IDE_RANGE |
+			    PCI_BASE_ADDRESS_SPACE_IO;
+			lo &= ~SOFT_BAR_IDE_FLAG;
+			_wrmsr(GLCP_MSR_REG(GLCP_SOFT_COM), hi, lo);
+		} else {
+			_rdmsr(IDE_MSR_REG(IDE_IO_BAR), &hi, &lo);
+			conf_data = lo & 0xfffffff0;
+			conf_data |= 0x01;
+			conf_data &= ~0x02;
+		}
+		break;
+	case PCI_CARDBUS_CIS:
+		conf_data = PCI_CARDBUS_CIS_POINTER;
+		break;
+	case PCI_SUBSYSTEM_VENDOR_ID:
+		conf_data =
+		    CFG_PCI_VENDOR_ID(CS5536_IDE_SUB_ID, CS5536_SUB_VENDOR_ID);
+		break;
+	case PCI_ROM_ADDRESS:
+		conf_data = PCI_EXPANSION_ROM_BAR;
+		break;
+	case PCI_CAPABILITY_LIST:
+		conf_data = PCI_CAPLIST_POINTER;
+		break;
+	case PCI_INTERRUPT_LINE:
+		conf_data =
+		    CFG_PCI_INTERRUPT_LINE(PCI_DEFAULT_PIN, CS5536_IDE_INTR);
+		break;
+	case PCI_IDE_CFG_REG:
+		_rdmsr(IDE_MSR_REG(IDE_CFG), &hi, &lo);
+		conf_data = lo;
+		break;
+	case PCI_IDE_DTC_REG:
+		_rdmsr(IDE_MSR_REG(IDE_DTC), &hi, &lo);
+		conf_data = lo;
+		break;
+	case PCI_IDE_CAST_REG:
+		_rdmsr(IDE_MSR_REG(IDE_CAST), &hi, &lo);
+		conf_data = lo;
+		break;
+	case PCI_IDE_ETC_REG:
+		_rdmsr(IDE_MSR_REG(IDE_ETC), &hi, &lo);
+		conf_data = lo;
+		break;
+	case PCI_IDE_PM_REG:
+		_rdmsr(IDE_MSR_REG(IDE_INTERNAL_PM), &hi, &lo);
+		conf_data = lo;
+		break;
+	default:
+		break;
+	}
+
+	return conf_data;
+}
diff --git a/arch/mips/loongson2ef/common/cs5536/cs5536_isa.c b/arch/mips/loongson2ef/common/cs5536/cs5536_isa.c
new file mode 100644
index 000000000..5ad38f86e
--- /dev/null
+++ b/arch/mips/loongson2ef/common/cs5536/cs5536_isa.c
@@ -0,0 +1,326 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * the ISA Virtual Support Module of AMD CS5536
+ *
+ * Copyright (C) 2007 Lemote, Inc.
+ * Author : jlliu, liujl@lemote.com
+ *
+ * Copyright (C) 2009 Lemote, Inc.
+ * Author: Wu Zhangjin, wuzhangjin@gmail.com
+ */
+
+#include <linux/pci.h>
+#include <cs5536/cs5536.h>
+#include <cs5536/cs5536_pci.h>
+
+/* common variables for PCI_ISA_READ/WRITE_BAR */
+static const u32 divil_msr_reg[6] = {
+	DIVIL_MSR_REG(DIVIL_LBAR_SMB), DIVIL_MSR_REG(DIVIL_LBAR_GPIO),
+	DIVIL_MSR_REG(DIVIL_LBAR_MFGPT), DIVIL_MSR_REG(DIVIL_LBAR_IRQ),
+	DIVIL_MSR_REG(DIVIL_LBAR_PMS), DIVIL_MSR_REG(DIVIL_LBAR_ACPI),
+};
+
+static const u32 soft_bar_flag[6] = {
+	SOFT_BAR_SMB_FLAG, SOFT_BAR_GPIO_FLAG, SOFT_BAR_MFGPT_FLAG,
+	SOFT_BAR_IRQ_FLAG, SOFT_BAR_PMS_FLAG, SOFT_BAR_ACPI_FLAG,
+};
+
+static const u32 sb_msr_reg[6] = {
+	SB_MSR_REG(SB_R0), SB_MSR_REG(SB_R1), SB_MSR_REG(SB_R2),
+	SB_MSR_REG(SB_R3), SB_MSR_REG(SB_R4), SB_MSR_REG(SB_R5),
+};
+
+static const u32 bar_space_range[6] = {
+	CS5536_SMB_RANGE, CS5536_GPIO_RANGE, CS5536_MFGPT_RANGE,
+	CS5536_IRQ_RANGE, CS5536_PMS_RANGE, CS5536_ACPI_RANGE,
+};
+
+static const int bar_space_len[6] = {
+	CS5536_SMB_LENGTH, CS5536_GPIO_LENGTH, CS5536_MFGPT_LENGTH,
+	CS5536_IRQ_LENGTH, CS5536_PMS_LENGTH, CS5536_ACPI_LENGTH,
+};
+
+/*
+ * enable the divil module bar space.
+ *
+ * For all the DIVIL module LBAR, you should control the DIVIL LBAR reg
+ * and the RCONFx(0~5) reg to use the modules.
+ */
+static void divil_lbar_enable(void)
+{
+	u32 hi, lo;
+	int offset;
+
+	/*
+	 * The DIVIL IRQ is not used yet. and make the RCONF0 reserved.
+	 */
+
+	for (offset = DIVIL_LBAR_SMB; offset <= DIVIL_LBAR_PMS; offset++) {
+		_rdmsr(DIVIL_MSR_REG(offset), &hi, &lo);
+		hi |= 0x01;
+		_wrmsr(DIVIL_MSR_REG(offset), hi, lo);
+	}
+}
+
+/*
+ * disable the divil module bar space.
+ */
+static void divil_lbar_disable(void)
+{
+	u32 hi, lo;
+	int offset;
+
+	for (offset = DIVIL_LBAR_SMB; offset <= DIVIL_LBAR_PMS; offset++) {
+		_rdmsr(DIVIL_MSR_REG(offset), &hi, &lo);
+		hi &= ~0x01;
+		_wrmsr(DIVIL_MSR_REG(offset), hi, lo);
+	}
+}
+
+/*
+ * BAR write: write value to the n BAR
+ */
+
+void pci_isa_write_bar(int n, u32 value)
+{
+	u32 hi = 0, lo = value;
+
+	if (value == PCI_BAR_RANGE_MASK) {
+		_rdmsr(GLCP_MSR_REG(GLCP_SOFT_COM), &hi, &lo);
+		lo |= soft_bar_flag[n];
+		_wrmsr(GLCP_MSR_REG(GLCP_SOFT_COM), hi, lo);
+	} else if (value & 0x01) {
+		/* NATIVE reg */
+		hi = 0x0000f001;
+		lo &= bar_space_range[n];
+		_wrmsr(divil_msr_reg[n], hi, lo);
+
+		/* RCONFx is 4bytes in units for I/O space */
+		hi = ((value & 0x000ffffc) << 12) |
+		    ((bar_space_len[n] - 4) << 12) | 0x01;
+		lo = ((value & 0x000ffffc) << 12) | 0x01;
+		_wrmsr(sb_msr_reg[n], hi, lo);
+	}
+}
+
+/*
+ * BAR read: read the n BAR
+ */
+
+u32 pci_isa_read_bar(int n)
+{
+	u32 conf_data = 0;
+	u32 hi, lo;
+
+	_rdmsr(GLCP_MSR_REG(GLCP_SOFT_COM), &hi, &lo);
+	if (lo & soft_bar_flag[n]) {
+		conf_data = bar_space_range[n] | PCI_BASE_ADDRESS_SPACE_IO;
+		lo &= ~soft_bar_flag[n];
+		_wrmsr(GLCP_MSR_REG(GLCP_SOFT_COM), hi, lo);
+	} else {
+		_rdmsr(divil_msr_reg[n], &hi, &lo);
+		conf_data = lo & bar_space_range[n];
+		conf_data |= 0x01;
+		conf_data &= ~0x02;
+	}
+	return conf_data;
+}
+
+/*
+ * isa_write: ISA write transfer
+ *
+ * We assume that this is not a bus master transfer.
+ */
+void pci_isa_write_reg(int reg, u32 value)
+{
+	u32 hi = 0, lo = value;
+	u32 temp;
+
+	switch (reg) {
+	case PCI_COMMAND:
+		if (value & PCI_COMMAND_IO)
+			divil_lbar_enable();
+		else
+			divil_lbar_disable();
+		break;
+	case PCI_STATUS:
+		_rdmsr(SB_MSR_REG(SB_ERROR), &hi, &lo);
+		temp = lo & 0x0000ffff;
+		if ((value & PCI_STATUS_SIG_TARGET_ABORT) &&
+		    (lo & SB_TAS_ERR_EN))
+			temp |= SB_TAS_ERR_FLAG;
+
+		if ((value & PCI_STATUS_REC_TARGET_ABORT) &&
+		    (lo & SB_TAR_ERR_EN))
+			temp |= SB_TAR_ERR_FLAG;
+
+		if ((value & PCI_STATUS_REC_MASTER_ABORT)
+		    && (lo & SB_MAR_ERR_EN))
+			temp |= SB_MAR_ERR_FLAG;
+
+		if ((value & PCI_STATUS_DETECTED_PARITY)
+		    && (lo & SB_PARE_ERR_EN))
+			temp |= SB_PARE_ERR_FLAG;
+
+		lo = temp;
+		_wrmsr(SB_MSR_REG(SB_ERROR), hi, lo);
+		break;
+	case PCI_CACHE_LINE_SIZE:
+		value &= 0x0000ff00;
+		_rdmsr(SB_MSR_REG(SB_CTRL), &hi, &lo);
+		hi &= 0xffffff00;
+		hi |= (value >> 8);
+		_wrmsr(SB_MSR_REG(SB_CTRL), hi, lo);
+		break;
+	case PCI_BAR0_REG:
+		pci_isa_write_bar(0, value);
+		break;
+	case PCI_BAR1_REG:
+		pci_isa_write_bar(1, value);
+		break;
+	case PCI_BAR2_REG:
+		pci_isa_write_bar(2, value);
+		break;
+	case PCI_BAR3_REG:
+		pci_isa_write_bar(3, value);
+		break;
+	case PCI_BAR4_REG:
+		pci_isa_write_bar(4, value);
+		break;
+	case PCI_BAR5_REG:
+		pci_isa_write_bar(5, value);
+		break;
+	case PCI_UART1_INT_REG:
+		_rdmsr(DIVIL_MSR_REG(PIC_YSEL_HIGH), &hi, &lo);
+		/* disable uart1 interrupt in PIC */
+		lo &= ~(0xf << 24);
+		if (value)	/* enable uart1 interrupt in PIC */
+			lo |= (CS5536_UART1_INTR << 24);
+		_wrmsr(DIVIL_MSR_REG(PIC_YSEL_HIGH), hi, lo);
+		break;
+	case PCI_UART2_INT_REG:
+		_rdmsr(DIVIL_MSR_REG(PIC_YSEL_HIGH), &hi, &lo);
+		/* disable uart2 interrupt in PIC */
+		lo &= ~(0xf << 28);
+		if (value)	/* enable uart2 interrupt in PIC */
+			lo |= (CS5536_UART2_INTR << 28);
+		_wrmsr(DIVIL_MSR_REG(PIC_YSEL_HIGH), hi, lo);
+		break;
+	case PCI_ISA_FIXUP_REG:
+		if (value) {
+			/* enable the TARGET ABORT/MASTER ABORT etc. */
+			_rdmsr(SB_MSR_REG(SB_ERROR), &hi, &lo);
+			lo |= 0x00000063;
+			_wrmsr(SB_MSR_REG(SB_ERROR), hi, lo);
+		}
+
+	default:
+		/* ALL OTHER PCI CONFIG SPACE HEADER IS NOT IMPLEMENTED. */
+		break;
+	}
+}
+
+/*
+ * isa_read: ISA read transfers
+ *
+ * We assume that this is not a bus master transfer.
+ */
+u32 pci_isa_read_reg(int reg)
+{
+	u32 conf_data = 0;
+	u32 hi, lo;
+
+	switch (reg) {
+	case PCI_VENDOR_ID:
+		conf_data =
+		    CFG_PCI_VENDOR_ID(CS5536_ISA_DEVICE_ID, CS5536_VENDOR_ID);
+		break;
+	case PCI_COMMAND:
+		/* we just check the first LBAR for the IO enable bit, */
+		/* maybe we should changed later. */
+		_rdmsr(DIVIL_MSR_REG(DIVIL_LBAR_SMB), &hi, &lo);
+		if (hi & 0x01)
+			conf_data |= PCI_COMMAND_IO;
+		break;
+	case PCI_STATUS:
+		conf_data |= PCI_STATUS_66MHZ;
+		conf_data |= PCI_STATUS_DEVSEL_MEDIUM;
+		conf_data |= PCI_STATUS_FAST_BACK;
+
+		_rdmsr(SB_MSR_REG(SB_ERROR), &hi, &lo);
+		if (lo & SB_TAS_ERR_FLAG)
+			conf_data |= PCI_STATUS_SIG_TARGET_ABORT;
+		if (lo & SB_TAR_ERR_FLAG)
+			conf_data |= PCI_STATUS_REC_TARGET_ABORT;
+		if (lo & SB_MAR_ERR_FLAG)
+			conf_data |= PCI_STATUS_REC_MASTER_ABORT;
+		if (lo & SB_PARE_ERR_FLAG)
+			conf_data |= PCI_STATUS_DETECTED_PARITY;
+		break;
+	case PCI_CLASS_REVISION:
+		_rdmsr(GLCP_MSR_REG(GLCP_CHIP_REV_ID), &hi, &lo);
+		conf_data = lo & 0x000000ff;
+		conf_data |= (CS5536_ISA_CLASS_CODE << 8);
+		break;
+	case PCI_CACHE_LINE_SIZE:
+		_rdmsr(SB_MSR_REG(SB_CTRL), &hi, &lo);
+		hi &= 0x000000f8;
+		conf_data = CFG_PCI_CACHE_LINE_SIZE(PCI_BRIDGE_HEADER_TYPE, hi);
+		break;
+		/*
+		 * we only use the LBAR of DIVIL, no RCONF used.
+		 * all of them are IO space.
+		 */
+	case PCI_BAR0_REG:
+		return pci_isa_read_bar(0);
+		break;
+	case PCI_BAR1_REG:
+		return pci_isa_read_bar(1);
+		break;
+	case PCI_BAR2_REG:
+		return pci_isa_read_bar(2);
+		break;
+	case PCI_BAR3_REG:
+		break;
+	case PCI_BAR4_REG:
+		return pci_isa_read_bar(4);
+		break;
+	case PCI_BAR5_REG:
+		return pci_isa_read_bar(5);
+		break;
+	case PCI_CARDBUS_CIS:
+		conf_data = PCI_CARDBUS_CIS_POINTER;
+		break;
+	case PCI_SUBSYSTEM_VENDOR_ID:
+		conf_data =
+		    CFG_PCI_VENDOR_ID(CS5536_ISA_SUB_ID, CS5536_SUB_VENDOR_ID);
+		break;
+	case PCI_ROM_ADDRESS:
+		conf_data = PCI_EXPANSION_ROM_BAR;
+		break;
+	case PCI_CAPABILITY_LIST:
+		conf_data = PCI_CAPLIST_POINTER;
+		break;
+	case PCI_INTERRUPT_LINE:
+		/* no interrupt used here */
+		conf_data = CFG_PCI_INTERRUPT_LINE(0x00, 0x00);
+		break;
+	default:
+		break;
+	}
+
+	return conf_data;
+}
+
+/*
+ * The mfgpt timer interrupt is running early, so we must keep the south bridge
+ * mmio always enabled. Otherwise we may race with the PCI configuration which
+ * may temporarily disable it. When that happens and the timer interrupt fires,
+ * we are not able to clear it and the system will hang.
+ */
+static void cs5536_isa_mmio_always_on(struct pci_dev *dev)
+{
+	dev->mmio_always_on = 1;
+}
+DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_ISA,
+	PCI_CLASS_BRIDGE_ISA, 8, cs5536_isa_mmio_always_on);
diff --git a/arch/mips/loongson2ef/common/cs5536/cs5536_mfgpt.c b/arch/mips/loongson2ef/common/cs5536/cs5536_mfgpt.c
new file mode 100644
index 000000000..f21a540a1
--- /dev/null
+++ b/arch/mips/loongson2ef/common/cs5536/cs5536_mfgpt.c
@@ -0,0 +1,203 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * CS5536 General timer functions
+ *
+ * Copyright (C) 2007 Lemote Inc. & Institute of Computing Technology
+ * Author: Yanhua, yanh@lemote.com
+ *
+ * Copyright (C) 2009 Lemote Inc.
+ * Author: Wu zhangjin, wuzhangjin@gmail.com
+ *
+ * Reference: AMD Geode(TM) CS5536 Companion Device Data Book
+ */
+
+#include <linux/io.h>
+#include <linux/init.h>
+#include <linux/export.h>
+#include <linux/jiffies.h>
+#include <linux/spinlock.h>
+#include <linux/interrupt.h>
+#include <linux/clockchips.h>
+
+#include <asm/time.h>
+
+#include <cs5536/cs5536_mfgpt.h>
+
+static DEFINE_RAW_SPINLOCK(mfgpt_lock);
+
+static u32 mfgpt_base;
+
+/*
+ * Initialize the MFGPT timer.
+ *
+ * This is also called after resume to bring the MFGPT into operation again.
+ */
+
+/* disable counter */
+void disable_mfgpt0_counter(void)
+{
+	outw(inw(MFGPT0_SETUP) & 0x7fff, MFGPT0_SETUP);
+}
+EXPORT_SYMBOL(disable_mfgpt0_counter);
+
+/* enable counter, comparator2 to event mode, 14.318MHz clock */
+void enable_mfgpt0_counter(void)
+{
+	outw(0xe310, MFGPT0_SETUP);
+}
+EXPORT_SYMBOL(enable_mfgpt0_counter);
+
+static int mfgpt_timer_set_periodic(struct clock_event_device *evt)
+{
+	raw_spin_lock(&mfgpt_lock);
+
+	outw(COMPARE, MFGPT0_CMP2);	/* set comparator2 */
+	outw(0, MFGPT0_CNT);		/* set counter to 0 */
+	enable_mfgpt0_counter();
+
+	raw_spin_unlock(&mfgpt_lock);
+	return 0;
+}
+
+static int mfgpt_timer_shutdown(struct clock_event_device *evt)
+{
+	if (clockevent_state_periodic(evt) || clockevent_state_oneshot(evt)) {
+		raw_spin_lock(&mfgpt_lock);
+		disable_mfgpt0_counter();
+		raw_spin_unlock(&mfgpt_lock);
+	}
+
+	return 0;
+}
+
+static struct clock_event_device mfgpt_clockevent = {
+	.name = "mfgpt",
+	.features = CLOCK_EVT_FEAT_PERIODIC,
+
+	/* The oneshot mode have very high deviation, don't use it! */
+	.set_state_shutdown = mfgpt_timer_shutdown,
+	.set_state_periodic = mfgpt_timer_set_periodic,
+	.irq = CS5536_MFGPT_INTR,
+};
+
+static irqreturn_t timer_interrupt(int irq, void *dev_id)
+{
+	u32 basehi;
+
+	/*
+	 * get MFGPT base address
+	 *
+	 * NOTE: do not remove me, it's need for the value of mfgpt_base is
+	 * variable
+	 */
+	_rdmsr(DIVIL_MSR_REG(DIVIL_LBAR_MFGPT), &basehi, &mfgpt_base);
+
+	/* ack */
+	outw(inw(MFGPT0_SETUP) | 0x4000, MFGPT0_SETUP);
+
+	mfgpt_clockevent.event_handler(&mfgpt_clockevent);
+
+	return IRQ_HANDLED;
+}
+
+/*
+ * Initialize the conversion factor and the min/max deltas of the clock event
+ * structure and register the clock event source with the framework.
+ */
+void __init setup_mfgpt0_timer(void)
+{
+	u32 basehi;
+	struct clock_event_device *cd = &mfgpt_clockevent;
+	unsigned int cpu = smp_processor_id();
+
+	cd->cpumask = cpumask_of(cpu);
+	clockevent_set_clock(cd, MFGPT_TICK_RATE);
+	cd->max_delta_ns = clockevent_delta2ns(0xffff, cd);
+	cd->max_delta_ticks = 0xffff;
+	cd->min_delta_ns = clockevent_delta2ns(0xf, cd);
+	cd->min_delta_ticks = 0xf;
+
+	/* Enable MFGPT0 Comparator 2 Output to the Interrupt Mapper */
+	_wrmsr(DIVIL_MSR_REG(MFGPT_IRQ), 0, 0x100);
+
+	/* Enable Interrupt Gate 5 */
+	_wrmsr(DIVIL_MSR_REG(PIC_ZSEL_LOW), 0, 0x50000);
+
+	/* get MFGPT base address */
+	_rdmsr(DIVIL_MSR_REG(DIVIL_LBAR_MFGPT), &basehi, &mfgpt_base);
+
+	clockevents_register_device(cd);
+
+	if (request_irq(CS5536_MFGPT_INTR, timer_interrupt,
+			IRQF_NOBALANCING | IRQF_TIMER, "timer", NULL))
+		pr_err("Failed to register timer interrupt\n");
+}
+
+/*
+ * Since the MFGPT overflows every tick, its not very useful
+ * to just read by itself. So use jiffies to emulate a free
+ * running counter:
+ */
+static u64 mfgpt_read(struct clocksource *cs)
+{
+	unsigned long flags;
+	int count;
+	u32 jifs;
+	static int old_count;
+	static u32 old_jifs;
+
+	raw_spin_lock_irqsave(&mfgpt_lock, flags);
+	/*
+	 * Although our caller may have the read side of xtime_lock,
+	 * this is now a seqlock, and we are cheating in this routine
+	 * by having side effects on state that we cannot undo if
+	 * there is a collision on the seqlock and our caller has to
+	 * retry.  (Namely, old_jifs and old_count.)  So we must treat
+	 * jiffies as volatile despite the lock.  We read jiffies
+	 * before latching the timer count to guarantee that although
+	 * the jiffies value might be older than the count (that is,
+	 * the counter may underflow between the last point where
+	 * jiffies was incremented and the point where we latch the
+	 * count), it cannot be newer.
+	 */
+	jifs = jiffies;
+	/* read the count */
+	count = inw(MFGPT0_CNT);
+
+	/*
+	 * It's possible for count to appear to go the wrong way for this
+	 * reason:
+	 *
+	 *  The timer counter underflows, but we haven't handled the resulting
+	 *  interrupt and incremented jiffies yet.
+	 *
+	 * Previous attempts to handle these cases intelligently were buggy, so
+	 * we just do the simple thing now.
+	 */
+	if (count < old_count && jifs == old_jifs)
+		count = old_count;
+
+	old_count = count;
+	old_jifs = jifs;
+
+	raw_spin_unlock_irqrestore(&mfgpt_lock, flags);
+
+	return (u64) (jifs * COMPARE) + count;
+}
+
+static struct clocksource clocksource_mfgpt = {
+	.name = "mfgpt",
+	.rating = 120, /* Functional for real use, but not desired */
+	.read = mfgpt_read,
+	.mask = CLOCKSOURCE_MASK(32),
+};
+
+int __init init_mfgpt_clocksource(void)
+{
+	if (num_possible_cpus() > 1)	/* MFGPT does not scale! */
+		return 0;
+
+	return clocksource_register_hz(&clocksource_mfgpt, MFGPT_TICK_RATE);
+}
+
+arch_initcall(init_mfgpt_clocksource);
diff --git a/arch/mips/loongson2ef/common/cs5536/cs5536_ohci.c b/arch/mips/loongson2ef/common/cs5536/cs5536_ohci.c
new file mode 100644
index 000000000..71a52b120
--- /dev/null
+++ b/arch/mips/loongson2ef/common/cs5536/cs5536_ohci.c
@@ -0,0 +1,145 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * the OHCI Virtual Support Module of AMD CS5536
+ *
+ * Copyright (C) 2007 Lemote, Inc.
+ * Author : jlliu, liujl@lemote.com
+ *
+ * Copyright (C) 2009 Lemote, Inc.
+ * Author: Wu Zhangjin, wuzhangjin@gmail.com
+ */
+
+#include <cs5536/cs5536.h>
+#include <cs5536/cs5536_pci.h>
+
+void pci_ohci_write_reg(int reg, u32 value)
+{
+	u32 hi = 0, lo = value;
+
+	switch (reg) {
+	case PCI_COMMAND:
+		_rdmsr(USB_MSR_REG(USB_OHCI), &hi, &lo);
+		if (value & PCI_COMMAND_MASTER)
+			hi |= PCI_COMMAND_MASTER;
+		else
+			hi &= ~PCI_COMMAND_MASTER;
+
+		if (value & PCI_COMMAND_MEMORY)
+			hi |= PCI_COMMAND_MEMORY;
+		else
+			hi &= ~PCI_COMMAND_MEMORY;
+		_wrmsr(USB_MSR_REG(USB_OHCI), hi, lo);
+		break;
+	case PCI_STATUS:
+		if (value & PCI_STATUS_PARITY) {
+			_rdmsr(SB_MSR_REG(SB_ERROR), &hi, &lo);
+			if (lo & SB_PARE_ERR_FLAG) {
+				lo = (lo & 0x0000ffff) | SB_PARE_ERR_FLAG;
+				_wrmsr(SB_MSR_REG(SB_ERROR), hi, lo);
+			}
+		}
+		break;
+	case PCI_BAR0_REG:
+		if (value == PCI_BAR_RANGE_MASK) {
+			_rdmsr(GLCP_MSR_REG(GLCP_SOFT_COM), &hi, &lo);
+			lo |= SOFT_BAR_OHCI_FLAG;
+			_wrmsr(GLCP_MSR_REG(GLCP_SOFT_COM), hi, lo);
+		} else if ((value & 0x01) == 0x00) {
+			_rdmsr(USB_MSR_REG(USB_OHCI), &hi, &lo);
+			lo = value;
+			_wrmsr(USB_MSR_REG(USB_OHCI), hi, lo);
+
+			value &= 0xfffffff0;
+			hi = 0x40000000 | ((value & 0xff000000) >> 24);
+			lo = 0x000fffff | ((value & 0x00fff000) << 8);
+			_wrmsr(GLIU_MSR_REG(GLIU_P2D_BM3), hi, lo);
+		}
+		break;
+	case PCI_OHCI_INT_REG:
+		_rdmsr(DIVIL_MSR_REG(PIC_YSEL_LOW), &hi, &lo);
+		lo &= ~(0xf << PIC_YSEL_LOW_USB_SHIFT);
+		if (value)	/* enable all the usb interrupt in PIC */
+			lo |= (CS5536_USB_INTR << PIC_YSEL_LOW_USB_SHIFT);
+		_wrmsr(DIVIL_MSR_REG(PIC_YSEL_LOW), hi, lo);
+		break;
+	default:
+		break;
+	}
+}
+
+u32 pci_ohci_read_reg(int reg)
+{
+	u32 conf_data = 0;
+	u32 hi, lo;
+
+	switch (reg) {
+	case PCI_VENDOR_ID:
+		conf_data =
+		    CFG_PCI_VENDOR_ID(CS5536_OHCI_DEVICE_ID, CS5536_VENDOR_ID);
+		break;
+	case PCI_COMMAND:
+		_rdmsr(USB_MSR_REG(USB_OHCI), &hi, &lo);
+		if (hi & PCI_COMMAND_MASTER)
+			conf_data |= PCI_COMMAND_MASTER;
+		if (hi & PCI_COMMAND_MEMORY)
+			conf_data |= PCI_COMMAND_MEMORY;
+		break;
+	case PCI_STATUS:
+		conf_data |= PCI_STATUS_66MHZ;
+		conf_data |= PCI_STATUS_FAST_BACK;
+		_rdmsr(SB_MSR_REG(SB_ERROR), &hi, &lo);
+		if (lo & SB_PARE_ERR_FLAG)
+			conf_data |= PCI_STATUS_PARITY;
+		conf_data |= PCI_STATUS_DEVSEL_MEDIUM;
+		break;
+	case PCI_CLASS_REVISION:
+		_rdmsr(USB_MSR_REG(USB_CAP), &hi, &lo);
+		conf_data = lo & 0x000000ff;
+		conf_data |= (CS5536_OHCI_CLASS_CODE << 8);
+		break;
+	case PCI_CACHE_LINE_SIZE:
+		conf_data =
+		    CFG_PCI_CACHE_LINE_SIZE(PCI_NORMAL_HEADER_TYPE,
+					    PCI_NORMAL_LATENCY_TIMER);
+		break;
+	case PCI_BAR0_REG:
+		_rdmsr(GLCP_MSR_REG(GLCP_SOFT_COM), &hi, &lo);
+		if (lo & SOFT_BAR_OHCI_FLAG) {
+			conf_data = CS5536_OHCI_RANGE |
+			    PCI_BASE_ADDRESS_SPACE_MEMORY;
+			lo &= ~SOFT_BAR_OHCI_FLAG;
+			_wrmsr(GLCP_MSR_REG(GLCP_SOFT_COM), hi, lo);
+		} else {
+			_rdmsr(USB_MSR_REG(USB_OHCI), &hi, &lo);
+			conf_data = lo & 0xffffff00;
+			conf_data &= ~0x0000000f;	/* 32bit mem */
+		}
+		break;
+	case PCI_CARDBUS_CIS:
+		conf_data = PCI_CARDBUS_CIS_POINTER;
+		break;
+	case PCI_SUBSYSTEM_VENDOR_ID:
+		conf_data =
+		    CFG_PCI_VENDOR_ID(CS5536_OHCI_SUB_ID, CS5536_SUB_VENDOR_ID);
+		break;
+	case PCI_ROM_ADDRESS:
+		conf_data = PCI_EXPANSION_ROM_BAR;
+		break;
+	case PCI_CAPABILITY_LIST:
+		conf_data = PCI_CAPLIST_USB_POINTER;
+		break;
+	case PCI_INTERRUPT_LINE:
+		conf_data =
+		    CFG_PCI_INTERRUPT_LINE(PCI_DEFAULT_PIN, CS5536_USB_INTR);
+		break;
+	case PCI_OHCI_INT_REG:
+		_rdmsr(DIVIL_MSR_REG(PIC_YSEL_LOW), &hi, &lo);
+		if (((lo >> PIC_YSEL_LOW_USB_SHIFT) & 0xf) == CS5536_USB_INTR)
+			conf_data = 1;
+		break;
+	default:
+		break;
+	}
+
+	return conf_data;
+}
diff --git a/arch/mips/loongson2ef/common/cs5536/cs5536_pci.c b/arch/mips/loongson2ef/common/cs5536/cs5536_pci.c
new file mode 100644
index 000000000..202c89b56
--- /dev/null
+++ b/arch/mips/loongson2ef/common/cs5536/cs5536_pci.c
@@ -0,0 +1,84 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * read/write operation to the PCI config space of CS5536
+ *
+ * Copyright (C) 2007 Lemote, Inc.
+ * Author : jlliu, liujl@lemote.com
+ *
+ * Copyright (C) 2009 Lemote, Inc.
+ * Author: Wu Zhangjin, wuzhangjin@gmail.com
+ *
+ *	the Virtual Support Module(VSM) for virtulizing the PCI
+ *	configure space are defined in cs5536_modulename.c respectively,
+ *
+ *	after this virtulizing, user can access the PCI configure space
+ *	directly as a normal multi-function PCI device which follows
+ *	the PCI-2.2 spec.
+ */
+
+#include <linux/types.h>
+#include <cs5536/cs5536_pci.h>
+#include <cs5536/cs5536_vsm.h>
+
+enum {
+	CS5536_FUNC_START = -1,
+	CS5536_ISA_FUNC,
+	reserved_func,
+	CS5536_IDE_FUNC,
+	CS5536_ACC_FUNC,
+	CS5536_OHCI_FUNC,
+	CS5536_EHCI_FUNC,
+	CS5536_FUNC_END,
+};
+
+static const cs5536_pci_vsm_write vsm_conf_write[] = {
+	[CS5536_ISA_FUNC]	= pci_isa_write_reg,
+	[reserved_func]		= NULL,
+	[CS5536_IDE_FUNC]	= pci_ide_write_reg,
+	[CS5536_ACC_FUNC]	= pci_acc_write_reg,
+	[CS5536_OHCI_FUNC]	= pci_ohci_write_reg,
+	[CS5536_EHCI_FUNC]	= pci_ehci_write_reg,
+};
+
+static const cs5536_pci_vsm_read vsm_conf_read[] = {
+	[CS5536_ISA_FUNC]	= pci_isa_read_reg,
+	[reserved_func]		= NULL,
+	[CS5536_IDE_FUNC]	= pci_ide_read_reg,
+	[CS5536_ACC_FUNC]	= pci_acc_read_reg,
+	[CS5536_OHCI_FUNC]	= pci_ohci_read_reg,
+	[CS5536_EHCI_FUNC]	= pci_ehci_read_reg,
+};
+
+/*
+ * write to PCI config space and transfer it to MSR write.
+ */
+void cs5536_pci_conf_write4(int function, int reg, u32 value)
+{
+	if ((function <= CS5536_FUNC_START) || (function >= CS5536_FUNC_END))
+		return;
+	if ((reg < 0) || (reg > 0x100) || ((reg & 0x03) != 0))
+		return;
+
+	if (vsm_conf_write[function] != NULL)
+		vsm_conf_write[function](reg, value);
+}
+
+/*
+ * read PCI config space and transfer it to MSR access.
+ */
+u32 cs5536_pci_conf_read4(int function, int reg)
+{
+	u32 data = 0;
+
+	if ((function <= CS5536_FUNC_START) || (function >= CS5536_FUNC_END))
+		return 0;
+	if ((reg < 0) || ((reg & 0x03) != 0))
+		return 0;
+	if (reg > 0x100)
+		return 0xffffffff;
+
+	if (vsm_conf_read[function] != NULL)
+		data = vsm_conf_read[function](reg);
+
+	return data;
+}
diff --git a/arch/mips/loongson2ef/common/env.c b/arch/mips/loongson2ef/common/env.c
new file mode 100644
index 000000000..6f20bdf9b
--- /dev/null
+++ b/arch/mips/loongson2ef/common/env.c
@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Based on Ocelot Linux port, which is
+ * Copyright 2001 MontaVista Software Inc.
+ * Author: jsun@mvista.com or jsun@junsun.net
+ *
+ * Copyright 2003 ICT CAS
+ * Author: Michael Guo <guoyi@ict.ac.cn>
+ *
+ * Copyright (C) 2007 Lemote Inc. & Institute of Computing Technology
+ * Author: Fuxin Zhang, zhangfx@lemote.com
+ *
+ * Copyright (C) 2009 Lemote Inc.
+ * Author: Wu Zhangjin, wuzhangjin@gmail.com
+ */
+#include <linux/export.h>
+#include <asm/bootinfo.h>
+#include <asm/fw/fw.h>
+#include <loongson.h>
+
+u32 cpu_clock_freq;
+EXPORT_SYMBOL(cpu_clock_freq);
+
+void __init prom_init_env(void)
+{
+	/* pmon passes arguments in 32bit pointers */
+	unsigned int processor_id;
+
+	cpu_clock_freq = fw_getenvl("cpuclock");
+	memsize = fw_getenvl("memsize");
+	highmemsize = fw_getenvl("highmemsize");
+
+	if (memsize == 0)
+		memsize = 256;
+
+	pr_info("memsize=%u, highmemsize=%u\n", memsize, highmemsize);
+
+	if (cpu_clock_freq == 0) {
+		processor_id = (&current_cpu_data)->processor_id;
+		switch (processor_id & PRID_REV_MASK) {
+		case PRID_REV_LOONGSON2E:
+			cpu_clock_freq = 533080000;
+			break;
+		case PRID_REV_LOONGSON2F:
+			cpu_clock_freq = 797000000;
+			break;
+		default:
+			cpu_clock_freq = 100000000;
+			break;
+		}
+	}
+	pr_info("CpuClock = %u\n", cpu_clock_freq);
+}
diff --git a/arch/mips/loongson2ef/common/init.c b/arch/mips/loongson2ef/common/init.c
new file mode 100644
index 000000000..779735935
--- /dev/null
+++ b/arch/mips/loongson2ef/common/init.c
@@ -0,0 +1,47 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2009 Lemote Inc.
+ * Author: Wu Zhangjin, wuzhangjin@gmail.com
+ */
+
+#include <linux/memblock.h>
+#include <asm/bootinfo.h>
+#include <asm/traps.h>
+#include <asm/smp-ops.h>
+#include <asm/cacheflush.h>
+#include <asm/fw/fw.h>
+
+#include <loongson.h>
+
+/* Loongson CPU address windows config space base address */
+unsigned long __maybe_unused _loongson_addrwincfg_base;
+
+static void __init mips_nmi_setup(void)
+{
+	void *base;
+
+	base = (void *)(CAC_BASE + 0x380);
+	memcpy(base, except_vec_nmi, 0x80);
+	flush_icache_range((unsigned long)base, (unsigned long)base + 0x80);
+}
+
+void __init prom_init(void)
+{
+#ifdef CONFIG_CPU_SUPPORTS_ADDRWINCFG
+	_loongson_addrwincfg_base = (unsigned long)
+		ioremap(LOONGSON_ADDRWINCFG_BASE, LOONGSON_ADDRWINCFG_SIZE);
+#endif
+
+	fw_init_cmdline();
+	prom_init_machtype();
+	prom_init_env();
+
+	/* init base address of io space */
+	set_io_port_base((unsigned long)
+		ioremap(LOONGSON_PCIIO_BASE, LOONGSON_PCIIO_SIZE));
+	prom_init_memory();
+
+	/*init the uart base address */
+	prom_init_uart_base();
+	board_nmi_handler_setup = mips_nmi_setup;
+}
diff --git a/arch/mips/loongson2ef/common/irq.c b/arch/mips/loongson2ef/common/irq.c
new file mode 100644
index 000000000..0ea93c1c0
--- /dev/null
+++ b/arch/mips/loongson2ef/common/irq.c
@@ -0,0 +1,63 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2007 Lemote Inc. & Institute of Computing Technology
+ * Author: Fuxin Zhang, zhangfx@lemote.com
+ */
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+
+#include <loongson.h>
+/*
+ * the first level int-handler will jump here if it is a bonito irq
+ */
+void bonito_irqdispatch(void)
+{
+	u32 int_status;
+	int i;
+
+	/* workaround the IO dma problem: let cpu looping to allow DMA finish */
+	int_status = LOONGSON_INTISR;
+	while (int_status & (1 << 10)) {
+		udelay(1);
+		int_status = LOONGSON_INTISR;
+	}
+
+	/* Get pending sources, masked by current enables */
+	int_status = LOONGSON_INTISR & LOONGSON_INTEN;
+
+	if (int_status) {
+		i = __ffs(int_status);
+		do_IRQ(LOONGSON_IRQ_BASE + i);
+	}
+}
+
+asmlinkage void plat_irq_dispatch(void)
+{
+	unsigned int pending;
+
+	pending = read_c0_cause() & read_c0_status() & ST0_IM;
+
+	/* machine-specific plat_irq_dispatch */
+	mach_irq_dispatch(pending);
+}
+
+void __init arch_init_irq(void)
+{
+	/*
+	 * Clear all of the interrupts while we change the able around a bit.
+	 * int-handler is not on bootstrap
+	 */
+	clear_c0_status(ST0_IM | ST0_BEV);
+
+	/* no steer */
+	LOONGSON_INTSTEER = 0;
+
+	/*
+	 * Mask out all interrupt by writing "1" to all bit position in
+	 * the interrupt reset reg.
+	 */
+	LOONGSON_INTENCLR = ~0;
+
+	/* machine specific irq init */
+	mach_init_irq();
+}
diff --git a/arch/mips/loongson2ef/common/machtype.c b/arch/mips/loongson2ef/common/machtype.c
new file mode 100644
index 000000000..82f6de49f
--- /dev/null
+++ b/arch/mips/loongson2ef/common/machtype.c
@@ -0,0 +1,62 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2009 Lemote Inc.
+ * Author: Wu Zhangjin, wuzhangjin@gmail.com
+ *
+ * Copyright (c) 2009 Zhang Le <r0bertz@gentoo.org>
+ */
+#include <linux/errno.h>
+#include <asm/bootinfo.h>
+
+#include <loongson.h>
+#include <machine.h>
+
+/* please ensure the length of the machtype string is less than 50 */
+#define MACHTYPE_LEN 50
+
+static const char *system_types[] = {
+	[MACH_LOONGSON_UNKNOWN]	= "unknown loongson machine",
+	[MACH_LEMOTE_FL2E]	= "lemote-fuloong-2e-box",
+	[MACH_LEMOTE_FL2F]	= "lemote-fuloong-2f-box",
+	[MACH_LEMOTE_ML2F7]	= "lemote-mengloong-2f-7inches",
+	[MACH_LEMOTE_YL2F89]	= "lemote-yeeloong-2f-8.9inches",
+	[MACH_DEXXON_GDIUM2F10]	= "dexxon-gdium-2f",
+	[MACH_LEMOTE_NAS]	= "lemote-nas-2f",
+	[MACH_LEMOTE_LL2F]	= "lemote-lynloong-2f",
+	[MACH_LOONGSON_END]	= NULL,
+};
+
+const char *get_system_type(void)
+{
+	return system_types[mips_machtype];
+}
+
+void __weak __init mach_prom_init_machtype(void)
+{
+}
+
+void __init prom_init_machtype(void)
+{
+	char *p, str[MACHTYPE_LEN + 1];
+	int machtype = MACH_LEMOTE_FL2E;
+
+	mips_machtype = LOONGSON_MACHTYPE;
+
+	p = strstr(arcs_cmdline, "machtype=");
+	if (!p) {
+		mach_prom_init_machtype();
+		return;
+	}
+	p += strlen("machtype=");
+	strncpy(str, p, MACHTYPE_LEN);
+	str[MACHTYPE_LEN] = '\0';
+	p = strstr(str, " ");
+	if (p)
+		*p = '\0';
+
+	for (; system_types[machtype]; machtype++)
+		if (strstr(system_types[machtype], str)) {
+			mips_machtype = machtype;
+			break;
+		}
+}
diff --git a/arch/mips/loongson2ef/common/mem.c b/arch/mips/loongson2ef/common/mem.c
new file mode 100644
index 000000000..fceb3ee47
--- /dev/null
+++ b/arch/mips/loongson2ef/common/mem.c
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ */
+#include <linux/fs.h>
+#include <linux/fcntl.h>
+#include <linux/memblock.h>
+#include <linux/mm.h>
+
+#include <asm/bootinfo.h>
+
+#include <loongson.h>
+#include <mem.h>
+#include <pci.h>
+
+
+u32 memsize, highmemsize;
+
+void __init prom_init_memory(void)
+{
+	memblock_add(0x0, (memsize << 20));
+
+#ifdef CONFIG_CPU_SUPPORTS_ADDRWINCFG
+	{
+		int bit;
+
+		bit = fls(memsize + highmemsize);
+		if (bit != ffs(memsize + highmemsize))
+			bit += 20;
+		else
+			bit = bit + 20 - 1;
+
+		/* set cpu window3 to map CPU to DDR: 2G -> 2G */
+		LOONGSON_ADDRWIN_CPUTODDR(ADDRWIN_WIN3, 0x80000000ul,
+					  0x80000000ul, (1 << bit));
+		mmiowb();
+	}
+#endif /* !CONFIG_CPU_SUPPORTS_ADDRWINCFG */
+
+#ifdef CONFIG_64BIT
+	if (highmemsize > 0)
+		memblock_add(LOONGSON_HIGHMEM_START, highmemsize << 20);
+#endif /* !CONFIG_64BIT */
+}
diff --git a/arch/mips/loongson2ef/common/pci.c b/arch/mips/loongson2ef/common/pci.c
new file mode 100644
index 000000000..7d9ea51e8
--- /dev/null
+++ b/arch/mips/loongson2ef/common/pci.c
@@ -0,0 +1,87 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2007 Lemote, Inc. & Institute of Computing Technology
+ * Author: Fuxin Zhang, zhangfx@lemote.com
+ */
+#include <linux/pci.h>
+
+#include <pci.h>
+#include <loongson.h>
+
+static struct resource loongson_pci_mem_resource = {
+	.name	= "pci memory space",
+	.start	= LOONGSON_PCI_MEM_START,
+	.end	= LOONGSON_PCI_MEM_END,
+	.flags	= IORESOURCE_MEM,
+};
+
+static struct resource loongson_pci_io_resource = {
+	.name	= "pci io space",
+	.start	= LOONGSON_PCI_IO_START,
+	.end	= IO_SPACE_LIMIT,
+	.flags	= IORESOURCE_IO,
+};
+
+static struct pci_controller  loongson_pci_controller = {
+	.pci_ops	= &loongson_pci_ops,
+	.io_resource	= &loongson_pci_io_resource,
+	.mem_resource	= &loongson_pci_mem_resource,
+	.mem_offset	= 0x00000000UL,
+	.io_offset	= 0x00000000UL,
+};
+
+static void __init setup_pcimap(void)
+{
+	/*
+	 * local to PCI mapping for CPU accessing PCI space
+	 * CPU address space [256M,448M] is window for accessing pci space
+	 * we set pcimap_lo[0,1,2] to map it to pci space[0M,64M], [320M,448M]
+	 *
+	 * pcimap: PCI_MAP2  PCI_Mem_Lo2 PCI_Mem_Lo1 PCI_Mem_Lo0
+	 *	     [<2G]   [384M,448M] [320M,384M] [0M,64M]
+	 */
+	LOONGSON_PCIMAP = LOONGSON_PCIMAP_PCIMAP_2 |
+		LOONGSON_PCIMAP_WIN(2, LOONGSON_PCILO2_BASE) |
+		LOONGSON_PCIMAP_WIN(1, LOONGSON_PCILO1_BASE) |
+		LOONGSON_PCIMAP_WIN(0, 0);
+
+	/*
+	 * PCI-DMA to local mapping: [2G,2G+256M] -> [0M,256M]
+	 */
+	LOONGSON_PCIBASE0 = 0x80000000ul;   /* base: 2G -> mmap: 0M */
+	/* size: 256M, burst transmission, pre-fetch enable, 64bit */
+	LOONGSON_PCI_HIT0_SEL_L = 0xc000000cul;
+	LOONGSON_PCI_HIT0_SEL_H = 0xfffffffful;
+	LOONGSON_PCI_HIT1_SEL_L = 0x00000006ul; /* set this BAR as invalid */
+	LOONGSON_PCI_HIT1_SEL_H = 0x00000000ul;
+	LOONGSON_PCI_HIT2_SEL_L = 0x00000006ul; /* set this BAR as invalid */
+	LOONGSON_PCI_HIT2_SEL_H = 0x00000000ul;
+
+	/* avoid deadlock of PCI reading/writing lock operation */
+	LOONGSON_PCI_ISR4C = 0xd2000001ul;
+
+	/* can not change gnt to break pci transfer when device's gnt not
+	deassert for some broken device */
+	LOONGSON_PXARB_CFG = 0x00fe0105ul;
+
+#ifdef CONFIG_CPU_SUPPORTS_ADDRWINCFG
+	/*
+	 * set cpu addr window2 to map CPU address space to PCI address space
+	 */
+	LOONGSON_ADDRWIN_CPUTOPCI(ADDRWIN_WIN2, LOONGSON_CPU_MEM_SRC,
+		LOONGSON_PCI_MEM_DST, MMAP_CPUTOPCI_SIZE);
+#endif
+}
+
+static int __init pcibios_init(void)
+{
+	setup_pcimap();
+
+	loongson_pci_controller.io_map_base = mips_io_port_base;
+	register_pci_controller(&loongson_pci_controller);
+
+
+	return 0;
+}
+
+arch_initcall(pcibios_init);
diff --git a/arch/mips/loongson2ef/common/platform.c b/arch/mips/loongson2ef/common/platform.c
new file mode 100644
index 000000000..0084820cf
--- /dev/null
+++ b/arch/mips/loongson2ef/common/platform.c
@@ -0,0 +1,27 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2009 Lemote Inc.
+ * Author: Wu Zhangjin, wuzhangjin@gmail.com
+ */
+
+#include <linux/err.h>
+#include <linux/smp.h>
+#include <linux/platform_device.h>
+
+static struct platform_device loongson2_cpufreq_device = {
+	.name = "loongson2_cpufreq",
+	.id = -1,
+};
+
+static int __init loongson2_cpufreq_init(void)
+{
+	struct cpuinfo_mips *c = &current_cpu_data;
+
+	/* Only 2F revision and it's successors support CPUFreq */
+	if ((c->processor_id & PRID_REV_MASK) >= PRID_REV_LOONGSON2F)
+		return platform_device_register(&loongson2_cpufreq_device);
+
+	return -ENODEV;
+}
+
+arch_initcall(loongson2_cpufreq_init);
diff --git a/arch/mips/loongson2ef/common/pm.c b/arch/mips/loongson2ef/common/pm.c
new file mode 100644
index 000000000..bcb7ae977
--- /dev/null
+++ b/arch/mips/loongson2ef/common/pm.c
@@ -0,0 +1,158 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * loongson-specific suspend support
+ *
+ *  Copyright (C) 2009 Lemote Inc.
+ *  Author: Wu Zhangjin <wuzhangjin@gmail.com>
+ */
+#include <linux/suspend.h>
+#include <linux/interrupt.h>
+#include <linux/pm.h>
+
+#include <asm/i8259.h>
+#include <asm/mipsregs.h>
+
+#include <loongson.h>
+
+static unsigned int __maybe_unused cached_master_mask;	/* i8259A */
+static unsigned int __maybe_unused cached_slave_mask;
+static unsigned int __maybe_unused cached_bonito_irq_mask; /* bonito */
+
+void arch_suspend_disable_irqs(void)
+{
+	/* disable all mips events */
+	local_irq_disable();
+
+#ifdef CONFIG_I8259
+	/* disable all events of i8259A */
+	cached_slave_mask = inb(PIC_SLAVE_IMR);
+	cached_master_mask = inb(PIC_MASTER_IMR);
+
+	outb(0xff, PIC_SLAVE_IMR);
+	inb(PIC_SLAVE_IMR);
+	outb(0xff, PIC_MASTER_IMR);
+	inb(PIC_MASTER_IMR);
+#endif
+	/* disable all events of bonito */
+	cached_bonito_irq_mask = LOONGSON_INTEN;
+	LOONGSON_INTENCLR = 0xffff;
+	(void)LOONGSON_INTENCLR;
+}
+
+void arch_suspend_enable_irqs(void)
+{
+	/* enable all mips events */
+	local_irq_enable();
+#ifdef CONFIG_I8259
+	/* only enable the cached events of i8259A */
+	outb(cached_slave_mask, PIC_SLAVE_IMR);
+	outb(cached_master_mask, PIC_MASTER_IMR);
+#endif
+	/* enable all cached events of bonito */
+	LOONGSON_INTENSET = cached_bonito_irq_mask;
+	(void)LOONGSON_INTENSET;
+}
+
+/*
+ * Setup the board-specific events for waking up loongson from wait mode
+ */
+void __weak setup_wakeup_events(void)
+{
+}
+
+/*
+ * Check wakeup events
+ */
+int __weak wakeup_loongson(void)
+{
+	return 1;
+}
+
+/*
+ * If the events are really what we want to wakeup the CPU, wake it up
+ * otherwise put the CPU asleep again.
+ */
+static void wait_for_wakeup_events(void)
+{
+	while (!wakeup_loongson())
+		writel(readl(LOONGSON_CHIPCFG) & ~0x7, LOONGSON_CHIPCFG);
+}
+
+/*
+ * Stop all perf counters
+ *
+ * $24 is the control register of Loongson perf counter
+ */
+static inline void stop_perf_counters(void)
+{
+	__write_64bit_c0_register($24, 0, 0);
+}
+
+
+static void loongson_suspend_enter(void)
+{
+	unsigned int cached_cpu_freq;
+
+	/* setup wakeup events via enabling the IRQs */
+	setup_wakeup_events();
+
+	stop_perf_counters();
+
+	cached_cpu_freq = readl(LOONGSON_CHIPCFG);
+
+	/* Put CPU into wait mode */
+	writel(readl(LOONGSON_CHIPCFG) & ~0x7, LOONGSON_CHIPCFG);
+
+	/* wait for the given events to wakeup cpu from wait mode */
+	wait_for_wakeup_events();
+
+	writel(cached_cpu_freq, LOONGSON_CHIPCFG);
+
+	mmiowb();
+}
+
+void __weak mach_suspend(void)
+{
+}
+
+void __weak mach_resume(void)
+{
+}
+
+static int loongson_pm_enter(suspend_state_t state)
+{
+	mach_suspend();
+
+	/* processor specific suspend */
+	loongson_suspend_enter();
+
+	mach_resume();
+
+	return 0;
+}
+
+static int loongson_pm_valid_state(suspend_state_t state)
+{
+	switch (state) {
+	case PM_SUSPEND_ON:
+	case PM_SUSPEND_STANDBY:
+	case PM_SUSPEND_MEM:
+		return 1;
+
+	default:
+		return 0;
+	}
+}
+
+static const struct platform_suspend_ops loongson_pm_ops = {
+	.valid	= loongson_pm_valid_state,
+	.enter	= loongson_pm_enter,
+};
+
+static int __init loongson_pm_init(void)
+{
+	suspend_set_ops(&loongson_pm_ops);
+
+	return 0;
+}
+arch_initcall(loongson_pm_init);
diff --git a/arch/mips/loongson2ef/common/reset.c b/arch/mips/loongson2ef/common/reset.c
new file mode 100644
index 000000000..e49c40646
--- /dev/null
+++ b/arch/mips/loongson2ef/common/reset.c
@@ -0,0 +1,73 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *
+ * Copyright (C) 2007 Lemote, Inc. & Institute of Computing Technology
+ * Author: Fuxin Zhang, zhangfx@lemote.com
+ * Copyright (C) 2009 Lemote, Inc.
+ * Author: Zhangjin Wu, wuzhangjin@gmail.com
+ */
+#include <linux/init.h>
+#include <linux/pm.h>
+
+#include <asm/idle.h>
+#include <asm/reboot.h>
+
+#include <loongson.h>
+
+static inline void loongson_reboot(void)
+{
+#ifndef CONFIG_CPU_JUMP_WORKAROUNDS
+	((void (*)(void))ioremap(LOONGSON_BOOT_BASE, 4)) ();
+#else
+	void (*func)(void);
+
+	func = (void *)ioremap(LOONGSON_BOOT_BASE, 4);
+
+	__asm__ __volatile__(
+	"	.set	noat						\n"
+	"	jr	%[func]						\n"
+	"	.set	at						\n"
+	: /* No outputs */
+	: [func] "r" (func));
+#endif
+}
+
+static void loongson_restart(char *command)
+{
+	/* do preparation for reboot */
+	mach_prepare_reboot();
+
+	/* reboot via jumping to boot base address */
+	loongson_reboot();
+}
+
+static void loongson_poweroff(void)
+{
+	mach_prepare_shutdown();
+
+	/*
+	 * It needs a wait loop here, but mips/kernel/reset.c already calls
+	 * a generic delay loop, machine_hang(), so simply return.
+	 */
+	return;
+}
+
+static void loongson_halt(void)
+{
+	pr_notice("\n\n** You can safely turn off the power now **\n\n");
+	while (1) {
+		if (cpu_wait)
+			cpu_wait();
+	}
+}
+
+static int __init mips_reboot_setup(void)
+{
+	_machine_restart = loongson_restart;
+	_machine_halt = loongson_halt;
+	pm_power_off = loongson_poweroff;
+
+	return 0;
+}
+
+arch_initcall(mips_reboot_setup);
diff --git a/arch/mips/loongson2ef/common/rtc.c b/arch/mips/loongson2ef/common/rtc.c
new file mode 100644
index 000000000..8d7628c0f
--- /dev/null
+++ b/arch/mips/loongson2ef/common/rtc.c
@@ -0,0 +1,39 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *  Lemote Fuloong platform support
+ *
+ *  Copyright(c) 2010 Arnaud Patard <apatard@mandriva.com>
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/mc146818rtc.h>
+
+static struct resource loongson_rtc_resources[] = {
+	{
+		.start	= RTC_PORT(0),
+		.end	= RTC_PORT(1),
+		.flags	= IORESOURCE_IO,
+	}, {
+		.start	= RTC_IRQ,
+		.end	= RTC_IRQ,
+		.flags	= IORESOURCE_IRQ,
+	}
+};
+
+static struct platform_device loongson_rtc_device = {
+	.name		= "rtc_cmos",
+	.id		= -1,
+	.resource	= loongson_rtc_resources,
+	.num_resources	= ARRAY_SIZE(loongson_rtc_resources),
+};
+
+
+static int __init loongson_rtc_platform_init(void)
+{
+	platform_device_register(&loongson_rtc_device);
+	return 0;
+}
+
+device_initcall(loongson_rtc_platform_init);
diff --git a/arch/mips/loongson2ef/common/serial.c b/arch/mips/loongson2ef/common/serial.c
new file mode 100644
index 000000000..ac4f6e3eb
--- /dev/null
+++ b/arch/mips/loongson2ef/common/serial.c
@@ -0,0 +1,86 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2007 Ralf Baechle (ralf@linux-mips.org)
+ *
+ * Copyright (C) 2009 Lemote, Inc.
+ * Author: Yan hua (yanhua@lemote.com)
+ * Author: Wu Zhangjin (wuzhangjin@gmail.com)
+ */
+
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/serial_8250.h>
+
+#include <asm/bootinfo.h>
+
+#include <loongson.h>
+#include <machine.h>
+
+#define PORT(int, clk)			\
+{								\
+	.irq		= int,					\
+	.uartclk	= clk,					\
+	.iotype		= UPIO_PORT,				\
+	.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,	\
+	.regshift	= 0,					\
+}
+
+#define PORT_M(int, clk)				\
+{								\
+	.irq		= MIPS_CPU_IRQ_BASE + (int),		\
+	.uartclk	= clk,					\
+	.iotype		= UPIO_MEM,				\
+	.membase	= (void __iomem *)NULL,			\
+	.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,	\
+	.regshift	= 0,					\
+}
+
+static struct plat_serial8250_port uart8250_data[MACH_LOONGSON_END + 1] = {
+	[MACH_LOONGSON_UNKNOWN]	= {},
+	[MACH_LEMOTE_FL2E]	= PORT(4, 1843200),
+	[MACH_LEMOTE_FL2F]	= PORT(3, 1843200),
+	[MACH_LEMOTE_ML2F7]	= PORT_M(3, 3686400),
+	[MACH_LEMOTE_YL2F89]	= PORT_M(3, 3686400),
+	[MACH_DEXXON_GDIUM2F10]	= PORT_M(3, 3686400),
+	[MACH_LEMOTE_NAS]	= PORT_M(3, 3686400),
+	[MACH_LEMOTE_LL2F]	= PORT(3, 1843200),
+	[MACH_LOONGSON_END]	= {},
+};
+
+static struct platform_device uart8250_device = {
+	.name = "serial8250",
+	.id = PLAT8250_DEV_PLATFORM,
+};
+
+static int __init serial_init(void)
+{
+	unsigned char iotype;
+
+	iotype = uart8250_data[mips_machtype].iotype;
+
+	if (UPIO_MEM == iotype) {
+		uart8250_data[mips_machtype].mapbase =
+			loongson_uart_base;
+		uart8250_data[mips_machtype].membase =
+			(void __iomem *)_loongson_uart_base;
+	}
+	else if (UPIO_PORT == iotype)
+		uart8250_data[mips_machtype].iobase =
+			loongson_uart_base - LOONGSON_PCIIO_BASE;
+
+	memset(&uart8250_data[mips_machtype + 1], 0,
+			sizeof(struct plat_serial8250_port));
+	uart8250_device.dev.platform_data = &uart8250_data[mips_machtype];
+
+	return platform_device_register(&uart8250_device);
+}
+module_init(serial_init);
+
+static void __exit serial_exit(void)
+{
+	platform_device_unregister(&uart8250_device);
+}
+module_exit(serial_exit);
diff --git a/arch/mips/loongson2ef/common/setup.c b/arch/mips/loongson2ef/common/setup.c
new file mode 100644
index 000000000..4fd27f4f9
--- /dev/null
+++ b/arch/mips/loongson2ef/common/setup.c
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2007 Lemote Inc. & Institute of Computing Technology
+ * Author: Fuxin Zhang, zhangfx@lemote.com
+ */
+#include <linux/export.h>
+#include <linux/init.h>
+
+#include <asm/wbflush.h>
+#include <asm/bootinfo.h>
+
+#include <loongson.h>
+
+static void wbflush_loongson(void)
+{
+	asm(".set\tpush\n\t"
+	    ".set\tnoreorder\n\t"
+	    ".set mips3\n\t"
+	    "sync\n\t"
+	    "nop\n\t"
+	    ".set\tpop\n\t"
+	    ".set mips0\n\t");
+}
+
+void (*__wbflush)(void) = wbflush_loongson;
+EXPORT_SYMBOL(__wbflush);
+
+void __init plat_mem_setup(void)
+{
+}
diff --git a/arch/mips/loongson2ef/common/time.c b/arch/mips/loongson2ef/common/time.c
new file mode 100644
index 000000000..585741af4
--- /dev/null
+++ b/arch/mips/loongson2ef/common/time.c
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2007 Lemote, Inc. & Institute of Computing Technology
+ * Author: Fuxin Zhang, zhangfx@lemote.com
+ *
+ * Copyright (C) 2009 Lemote Inc.
+ * Author: Wu Zhangjin, wuzhangjin@gmail.com
+ */
+#include <asm/mc146818-time.h>
+#include <asm/time.h>
+#include <asm/hpet.h>
+
+#include <loongson.h>
+#include <cs5536/cs5536_mfgpt.h>
+
+void __init plat_time_init(void)
+{
+	/* setup mips r4k timer */
+	mips_hpt_frequency = cpu_clock_freq / 2;
+
+	setup_mfgpt0_timer();
+}
+
+void read_persistent_clock64(struct timespec64 *ts)
+{
+	ts->tv_sec = mc146818_get_cmos_time();
+	ts->tv_nsec = 0;
+}
diff --git a/arch/mips/loongson2ef/common/uart_base.c b/arch/mips/loongson2ef/common/uart_base.c
new file mode 100644
index 000000000..522bea6ad
--- /dev/null
+++ b/arch/mips/loongson2ef/common/uart_base.c
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2009 Lemote Inc.
+ * Author: Wu Zhangjin, wuzhangjin@gmail.com
+ */
+
+#include <linux/export.h>
+#include <asm/bootinfo.h>
+#include <asm/setup.h>
+
+#include <loongson.h>
+
+/* raw */
+unsigned long loongson_uart_base;
+/* ioremapped */
+unsigned long _loongson_uart_base;
+
+EXPORT_SYMBOL(loongson_uart_base);
+EXPORT_SYMBOL(_loongson_uart_base);
+
+void prom_init_loongson_uart_base(void)
+{
+	switch (mips_machtype) {
+	case MACH_LEMOTE_FL2E:
+		loongson_uart_base = LOONGSON_PCIIO_BASE + 0x3f8;
+		break;
+	case MACH_LEMOTE_FL2F:
+	case MACH_LEMOTE_LL2F:
+		loongson_uart_base = LOONGSON_PCIIO_BASE + 0x2f8;
+		break;
+	case MACH_LEMOTE_ML2F7:
+	case MACH_LEMOTE_YL2F89:
+	case MACH_DEXXON_GDIUM2F10:
+	case MACH_LEMOTE_NAS:
+	default:
+		/* The CPU provided serial port (LPC) */
+		loongson_uart_base = LOONGSON_LIO1_BASE + 0x3f8;
+		break;
+	}
+
+	_loongson_uart_base = TO_UNCAC(loongson_uart_base);
+	setup_8250_early_printk_port(_loongson_uart_base, 0, 1024);
+}
diff --git a/arch/mips/loongson2ef/fuloong-2e/Makefile b/arch/mips/loongson2ef/fuloong-2e/Makefile
new file mode 100644
index 000000000..bb58edb3b
--- /dev/null
+++ b/arch/mips/loongson2ef/fuloong-2e/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Makefile for Lemote Fuloong2e mini-PC board.
+#
+
+obj-y += irq.o reset.o dma.o
diff --git a/arch/mips/loongson2ef/fuloong-2e/dma.c b/arch/mips/loongson2ef/fuloong-2e/dma.c
new file mode 100644
index 000000000..cea167d8a
--- /dev/null
+++ b/arch/mips/loongson2ef/fuloong-2e/dma.c
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/dma-direct.h>
+
+dma_addr_t phys_to_dma(struct device *dev, phys_addr_t paddr)
+{
+	return paddr | 0x80000000;
+}
+
+phys_addr_t dma_to_phys(struct device *dev, dma_addr_t dma_addr)
+{
+	return dma_addr & 0x7fffffff;
+}
diff --git a/arch/mips/loongson2ef/fuloong-2e/irq.c b/arch/mips/loongson2ef/fuloong-2e/irq.c
new file mode 100644
index 000000000..b1c9d4ee0
--- /dev/null
+++ b/arch/mips/loongson2ef/fuloong-2e/irq.c
@@ -0,0 +1,65 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2007 Lemote Inc. & Institute of Computing Technology
+ * Author: Fuxin Zhang, zhangfx@lemote.com
+ */
+#include <linux/interrupt.h>
+
+#include <asm/irq_cpu.h>
+#include <asm/i8259.h>
+
+#include <loongson.h>
+
+static void i8259_irqdispatch(void)
+{
+	int irq;
+
+	irq = i8259_irq();
+	if (irq >= 0)
+		do_IRQ(irq);
+	else
+		spurious_interrupt();
+}
+
+asmlinkage void mach_irq_dispatch(unsigned int pending)
+{
+	if (pending & CAUSEF_IP7)
+		do_IRQ(MIPS_CPU_IRQ_BASE + 7);
+	else if (pending & CAUSEF_IP6) /* perf counter loverflow */
+		return;
+	else if (pending & CAUSEF_IP5)
+		i8259_irqdispatch();
+	else if (pending & CAUSEF_IP2)
+		bonito_irqdispatch();
+	else
+		spurious_interrupt();
+}
+
+void __init mach_init_irq(void)
+{
+	int irq;
+
+	/* init all controller
+	 *   0-15	  ------> i8259 interrupt
+	 *   16-23	  ------> mips cpu interrupt
+	 *   32-63	  ------> bonito irq
+	 */
+
+	/* most bonito irq should be level triggered */
+	LOONGSON_INTEDGE = LOONGSON_ICU_SYSTEMERR | LOONGSON_ICU_MASTERERR |
+	    LOONGSON_ICU_RETRYERR | LOONGSON_ICU_MBOXES;
+
+	/* Sets the first-level interrupt dispatcher. */
+	mips_cpu_irq_init();
+	init_i8259_irqs();
+	bonito_irq_init();
+
+	/* bonito irq at IP2 */
+	irq = MIPS_CPU_IRQ_BASE + 2;
+	if (request_irq(irq, no_action, IRQF_NO_THREAD, "cascade", NULL))
+		pr_err("Failed to request irq %d (cascade)\n", irq);
+	/* 8259 irq at IP5 */
+	irq = MIPS_CPU_IRQ_BASE + 5;
+	if (request_irq(irq, no_action, IRQF_NO_THREAD, "cascade", NULL))
+		pr_err("Failed to request irq %d (cascade)\n", irq);
+}
diff --git a/arch/mips/loongson2ef/fuloong-2e/reset.c b/arch/mips/loongson2ef/fuloong-2e/reset.c
new file mode 100644
index 000000000..8273de1cf
--- /dev/null
+++ b/arch/mips/loongson2ef/fuloong-2e/reset.c
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/* Board-specific reboot/shutdown routines
+ * Copyright (c) 2009 Philippe Vachon <philippe@cowpig.ca>
+ *
+ * Copyright (C) 2009 Lemote Inc.
+ * Author: Wu Zhangjin, wuzhangjin@gmail.com
+ */
+
+#include <loongson.h>
+
+void mach_prepare_reboot(void)
+{
+	LOONGSON_GENCFG &= ~(1 << 2);
+	LOONGSON_GENCFG |= (1 << 2);
+}
+
+void mach_prepare_shutdown(void)
+{
+}
diff --git a/arch/mips/loongson2ef/lemote-2f/Makefile b/arch/mips/loongson2ef/lemote-2f/Makefile
new file mode 100644
index 000000000..881a0ec06
--- /dev/null
+++ b/arch/mips/loongson2ef/lemote-2f/Makefile
@@ -0,0 +1,12 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Makefile for lemote loongson2f family machines
+#
+
+obj-y += clock.o machtype.o irq.o reset.o dma.o ec_kb3310b.o
+
+#
+# Suspend Support
+#
+
+obj-$(CONFIG_SUSPEND) += pm.o
diff --git a/arch/mips/loongson2ef/lemote-2f/clock.c b/arch/mips/loongson2ef/lemote-2f/clock.c
new file mode 100644
index 000000000..850b6b9f8
--- /dev/null
+++ b/arch/mips/loongson2ef/lemote-2f/clock.c
@@ -0,0 +1,51 @@
+/*
+ * Copyright (C) 2006 - 2008 Lemote Inc. & Institute of Computing Technology
+ * Author: Yanhua, yanh@lemote.com
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#include <linux/cpufreq.h>
+#include <linux/errno.h>
+#include <linux/export.h>
+
+#include <asm/mach-loongson2ef/loongson.h>
+
+enum {
+	DC_ZERO, DC_25PT = 2, DC_37PT, DC_50PT, DC_62PT, DC_75PT,
+	DC_87PT, DC_DISABLE, DC_RESV
+};
+
+struct cpufreq_frequency_table loongson2_clockmod_table[] = {
+	{0, DC_RESV, CPUFREQ_ENTRY_INVALID},
+	{0, DC_ZERO, CPUFREQ_ENTRY_INVALID},
+	{0, DC_25PT, 0},
+	{0, DC_37PT, 0},
+	{0, DC_50PT, 0},
+	{0, DC_62PT, 0},
+	{0, DC_75PT, 0},
+	{0, DC_87PT, 0},
+	{0, DC_DISABLE, 0},
+	{0, DC_RESV, CPUFREQ_TABLE_END},
+};
+EXPORT_SYMBOL_GPL(loongson2_clockmod_table);
+
+int loongson2_cpu_set_rate(unsigned long rate_khz)
+{
+	struct cpufreq_frequency_table *pos;
+	int regval;
+
+	cpufreq_for_each_valid_entry(pos, loongson2_clockmod_table)
+		if (rate_khz == pos->frequency)
+			break;
+	if (rate_khz != pos->frequency)
+		return -ENOTSUPP;
+
+	regval = readl(LOONGSON_CHIPCFG);
+	regval = (regval & ~0x7) | (pos->driver_data - 1);
+	writel(regval, LOONGSON_CHIPCFG);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(loongson2_cpu_set_rate);
diff --git a/arch/mips/loongson2ef/lemote-2f/dma.c b/arch/mips/loongson2ef/lemote-2f/dma.c
new file mode 100644
index 000000000..3c9e99456
--- /dev/null
+++ b/arch/mips/loongson2ef/lemote-2f/dma.c
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/dma-direct.h>
+
+dma_addr_t phys_to_dma(struct device *dev, phys_addr_t paddr)
+{
+	return paddr | 0x80000000;
+}
+
+phys_addr_t dma_to_phys(struct device *dev, dma_addr_t dma_addr)
+{
+	if (dma_addr > 0x8fffffff)
+		return dma_addr;
+	return dma_addr & 0x0fffffff;
+}
diff --git a/arch/mips/loongson2ef/lemote-2f/ec_kb3310b.c b/arch/mips/loongson2ef/lemote-2f/ec_kb3310b.c
new file mode 100644
index 000000000..d138220e9
--- /dev/null
+++ b/arch/mips/loongson2ef/lemote-2f/ec_kb3310b.c
@@ -0,0 +1,125 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Basic KB3310B Embedded Controller support for the YeeLoong 2F netbook
+ *
+ *  Copyright (C) 2008 Lemote Inc.
+ *  Author: liujl <liujl@lemote.com>, 2008-04-20
+ */
+
+#include <linux/io.h>
+#include <linux/export.h>
+#include <linux/spinlock.h>
+#include <linux/delay.h>
+
+#include "ec_kb3310b.h"
+
+static DEFINE_SPINLOCK(index_access_lock);
+static DEFINE_SPINLOCK(port_access_lock);
+
+unsigned char ec_read(unsigned short addr)
+{
+	unsigned char value;
+	unsigned long flags;
+
+	spin_lock_irqsave(&index_access_lock, flags);
+	outb((addr & 0xff00) >> 8, EC_IO_PORT_HIGH);
+	outb((addr & 0x00ff), EC_IO_PORT_LOW);
+	value = inb(EC_IO_PORT_DATA);
+	spin_unlock_irqrestore(&index_access_lock, flags);
+
+	return value;
+}
+EXPORT_SYMBOL_GPL(ec_read);
+
+void ec_write(unsigned short addr, unsigned char val)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&index_access_lock, flags);
+	outb((addr & 0xff00) >> 8, EC_IO_PORT_HIGH);
+	outb((addr & 0x00ff), EC_IO_PORT_LOW);
+	outb(val, EC_IO_PORT_DATA);
+	/*  flush the write action */
+	inb(EC_IO_PORT_DATA);
+	spin_unlock_irqrestore(&index_access_lock, flags);
+}
+EXPORT_SYMBOL_GPL(ec_write);
+
+/*
+ * This function is used for EC command writes and corresponding status queries.
+ */
+int ec_query_seq(unsigned char cmd)
+{
+	int timeout;
+	unsigned char status;
+	unsigned long flags;
+	int ret = 0;
+
+	spin_lock_irqsave(&port_access_lock, flags);
+
+	/* make chip goto reset mode */
+	udelay(EC_REG_DELAY);
+	outb(cmd, EC_CMD_PORT);
+	udelay(EC_REG_DELAY);
+
+	/* check if the command is received by ec */
+	timeout = EC_CMD_TIMEOUT;
+	status = inb(EC_STS_PORT);
+	while (timeout-- && (status & (1 << 1))) {
+		status = inb(EC_STS_PORT);
+		udelay(EC_REG_DELAY);
+	}
+
+	spin_unlock_irqrestore(&port_access_lock, flags);
+
+	if (timeout <= 0) {
+		printk(KERN_ERR "%s: deadable error : timeout...\n", __func__);
+		ret = -EINVAL;
+	} else
+		printk(KERN_INFO
+			   "(%x/%d)ec issued command %d status : 0x%x\n",
+			   timeout, EC_CMD_TIMEOUT - timeout, cmd, status);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(ec_query_seq);
+
+/*
+ * Send query command to EC to get the proper event number
+ */
+int ec_query_event_num(void)
+{
+	return ec_query_seq(CMD_GET_EVENT_NUM);
+}
+EXPORT_SYMBOL(ec_query_event_num);
+
+/*
+ * Get event number from EC
+ *
+ * NOTE: This routine must follow the query_event_num function in the
+ * interrupt.
+ */
+int ec_get_event_num(void)
+{
+	int timeout = 100;
+	unsigned char value;
+	unsigned char status;
+
+	udelay(EC_REG_DELAY);
+	status = inb(EC_STS_PORT);
+	udelay(EC_REG_DELAY);
+	while (timeout-- && !(status & (1 << 0))) {
+		status = inb(EC_STS_PORT);
+		udelay(EC_REG_DELAY);
+	}
+	if (timeout <= 0) {
+		pr_info("%s: get event number timeout.\n", __func__);
+
+		return -EINVAL;
+	}
+	value = inb(EC_DAT_PORT);
+	udelay(EC_REG_DELAY);
+
+	return value;
+}
+EXPORT_SYMBOL(ec_get_event_num);
diff --git a/arch/mips/loongson2ef/lemote-2f/ec_kb3310b.h b/arch/mips/loongson2ef/lemote-2f/ec_kb3310b.h
new file mode 100644
index 000000000..aecdbc9c8
--- /dev/null
+++ b/arch/mips/loongson2ef/lemote-2f/ec_kb3310b.h
@@ -0,0 +1,184 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * KB3310B Embedded Controller
+ *
+ *  Copyright (C) 2008 Lemote Inc.
+ *  Author: liujl <liujl@lemote.com>, 2008-03-14
+ */
+
+#ifndef _EC_KB3310B_H
+#define _EC_KB3310B_H
+
+extern unsigned char ec_read(unsigned short addr);
+extern void ec_write(unsigned short addr, unsigned char val);
+extern int ec_query_seq(unsigned char cmd);
+extern int ec_query_event_num(void);
+extern int ec_get_event_num(void);
+
+typedef int (*sci_handler) (int status);
+extern sci_handler yeeloong_report_lid_status;
+
+#define SCI_IRQ_NUM 0x0A
+
+/*
+ * The following registers are determined by the EC index configuration.
+ * 1, fill the PORT_HIGH as EC register high part.
+ * 2, fill the PORT_LOW as EC register low part.
+ * 3, fill the PORT_DATA as EC register write data or get the data from it.
+ */
+#define EC_IO_PORT_HIGH 0x0381
+#define EC_IO_PORT_LOW	0x0382
+#define EC_IO_PORT_DATA 0x0383
+
+/*
+ * EC delay time is 500us for register and status access
+ */
+#define EC_REG_DELAY	500	/* unit : us */
+#define EC_CMD_TIMEOUT	0x1000
+
+/*
+ * EC access port for SCI communication
+ */
+#define EC_CMD_PORT		0x66
+#define EC_STS_PORT		0x66
+#define EC_DAT_PORT		0x62
+#define CMD_INIT_IDLE_MODE	0xdd
+#define CMD_EXIT_IDLE_MODE	0xdf
+#define CMD_INIT_RESET_MODE	0xd8
+#define CMD_REBOOT_SYSTEM	0x8c
+#define CMD_GET_EVENT_NUM	0x84
+#define CMD_PROGRAM_PIECE	0xda
+
+/* temperature & fan registers */
+#define REG_TEMPERATURE_VALUE	0xF458
+#define REG_FAN_AUTO_MAN_SWITCH 0xF459
+#define BIT_FAN_AUTO		0
+#define BIT_FAN_MANUAL		1
+#define REG_FAN_CONTROL		0xF4D2
+#define BIT_FAN_CONTROL_ON	(1 << 0)
+#define BIT_FAN_CONTROL_OFF	(0 << 0)
+#define REG_FAN_STATUS		0xF4DA
+#define BIT_FAN_STATUS_ON	(1 << 0)
+#define BIT_FAN_STATUS_OFF	(0 << 0)
+#define REG_FAN_SPEED_HIGH	0xFE22
+#define REG_FAN_SPEED_LOW	0xFE23
+#define REG_FAN_SPEED_LEVEL	0xF4CC
+/* fan speed divider */
+#define FAN_SPEED_DIVIDER	480000	/* (60*1000*1000/62.5/2)*/
+
+/* battery registers */
+#define REG_BAT_DESIGN_CAP_HIGH		0xF77D
+#define REG_BAT_DESIGN_CAP_LOW		0xF77E
+#define REG_BAT_FULLCHG_CAP_HIGH	0xF780
+#define REG_BAT_FULLCHG_CAP_LOW		0xF781
+#define REG_BAT_DESIGN_VOL_HIGH		0xF782
+#define REG_BAT_DESIGN_VOL_LOW		0xF783
+#define REG_BAT_CURRENT_HIGH		0xF784
+#define REG_BAT_CURRENT_LOW		0xF785
+#define REG_BAT_VOLTAGE_HIGH		0xF786
+#define REG_BAT_VOLTAGE_LOW		0xF787
+#define REG_BAT_TEMPERATURE_HIGH	0xF788
+#define REG_BAT_TEMPERATURE_LOW		0xF789
+#define REG_BAT_RELATIVE_CAP_HIGH	0xF492
+#define REG_BAT_RELATIVE_CAP_LOW	0xF493
+#define REG_BAT_VENDOR			0xF4C4
+#define FLAG_BAT_VENDOR_SANYO		0x01
+#define FLAG_BAT_VENDOR_SIMPLO		0x02
+#define REG_BAT_CELL_COUNT		0xF4C6
+#define FLAG_BAT_CELL_3S1P		0x03
+#define FLAG_BAT_CELL_3S2P		0x06
+#define REG_BAT_CHARGE			0xF4A2
+#define FLAG_BAT_CHARGE_DISCHARGE	0x01
+#define FLAG_BAT_CHARGE_CHARGE		0x02
+#define FLAG_BAT_CHARGE_ACPOWER		0x00
+#define REG_BAT_STATUS			0xF4B0
+#define BIT_BAT_STATUS_LOW		(1 << 5)
+#define BIT_BAT_STATUS_DESTROY		(1 << 2)
+#define BIT_BAT_STATUS_FULL		(1 << 1)
+#define BIT_BAT_STATUS_IN		(1 << 0)
+#define REG_BAT_CHARGE_STATUS		0xF4B1
+#define BIT_BAT_CHARGE_STATUS_OVERTEMP	(1 << 2)
+#define BIT_BAT_CHARGE_STATUS_PRECHG	(1 << 1)
+#define REG_BAT_STATE			0xF482
+#define BIT_BAT_STATE_CHARGING		(1 << 1)
+#define BIT_BAT_STATE_DISCHARGING	(1 << 0)
+#define REG_BAT_POWER			0xF440
+#define BIT_BAT_POWER_S3		(1 << 2)
+#define BIT_BAT_POWER_ON		(1 << 1)
+#define BIT_BAT_POWER_ACIN		(1 << 0)
+
+/* other registers */
+/* Audio: rd/wr */
+#define REG_AUDIO_VOLUME	0xF46C
+#define REG_AUDIO_MUTE		0xF4E7
+#define REG_AUDIO_BEEP		0xF4D0
+/* USB port power or not: rd/wr */
+#define REG_USB0_FLAG		0xF461
+#define REG_USB1_FLAG		0xF462
+#define REG_USB2_FLAG		0xF463
+#define BIT_USB_FLAG_ON		1
+#define BIT_USB_FLAG_OFF	0
+/* LID */
+#define REG_LID_DETECT		0xF4BD
+#define BIT_LID_DETECT_ON	1
+#define BIT_LID_DETECT_OFF	0
+/* CRT */
+#define REG_CRT_DETECT		0xF4AD
+#define BIT_CRT_DETECT_PLUG	1
+#define BIT_CRT_DETECT_UNPLUG	0
+/* LCD backlight brightness adjust: 9 levels */
+#define REG_DISPLAY_BRIGHTNESS	0xF4F5
+/* Black screen Status */
+#define BIT_DISPLAY_LCD_ON	1
+#define BIT_DISPLAY_LCD_OFF	0
+/* LCD backlight control: off/restore */
+#define REG_BACKLIGHT_CTRL	0xF7BD
+#define BIT_BACKLIGHT_ON	1
+#define BIT_BACKLIGHT_OFF	0
+/* Reset the machine auto-clear: rd/wr */
+#define REG_RESET		0xF4EC
+#define BIT_RESET_ON		1
+/* Light the led: rd/wr */
+#define REG_LED			0xF4C8
+#define BIT_LED_RED_POWER	(1 << 0)
+#define BIT_LED_ORANGE_POWER	(1 << 1)
+#define BIT_LED_GREEN_CHARGE	(1 << 2)
+#define BIT_LED_RED_CHARGE	(1 << 3)
+#define BIT_LED_NUMLOCK		(1 << 4)
+/* Test led mode, all led on/off */
+#define REG_LED_TEST		0xF4C2
+#define BIT_LED_TEST_IN		1
+#define BIT_LED_TEST_OUT	0
+/* Camera on/off */
+#define REG_CAMERA_STATUS	0xF46A
+#define BIT_CAMERA_STATUS_ON	1
+#define BIT_CAMERA_STATUS_OFF	0
+#define REG_CAMERA_CONTROL	0xF7B7
+#define BIT_CAMERA_CONTROL_OFF	0
+#define BIT_CAMERA_CONTROL_ON	1
+/* Wlan Status */
+#define REG_WLAN		0xF4FA
+#define BIT_WLAN_ON		1
+#define BIT_WLAN_OFF		0
+#define REG_DISPLAY_LCD		0xF79F
+
+/* SCI Event Number from EC */
+enum {
+	EVENT_LID = 0x23,	/*  LID open/close */
+	EVENT_DISPLAY_TOGGLE,	/*  Fn+F3 for display switch */
+	EVENT_SLEEP,		/*  Fn+F1 for entering sleep mode */
+	EVENT_OVERTEMP,		/*  Over-temperature happened */
+	EVENT_CRT_DETECT,	/*  CRT is connected */
+	EVENT_CAMERA,		/*  Camera on/off */
+	EVENT_USB_OC2,		/*  USB2 Over Current occurred */
+	EVENT_USB_OC0,		/*  USB0 Over Current occurred */
+	EVENT_BLACK_SCREEN,	/*  Turn on/off backlight */
+	EVENT_AUDIO_MUTE,	/*  Mute on/off */
+	EVENT_DISPLAY_BRIGHTNESS,/* LCD backlight brightness adjust */
+	EVENT_AC_BAT,		/*  AC & Battery relative issue */
+	EVENT_AUDIO_VOLUME,	/*  Volume adjust */
+	EVENT_WLAN,		/*  Wlan on/off */
+	EVENT_END
+};
+
+#endif /* !_EC_KB3310B_H */
diff --git a/arch/mips/loongson2ef/lemote-2f/irq.c b/arch/mips/loongson2ef/lemote-2f/irq.c
new file mode 100644
index 000000000..f5a731a2a
--- /dev/null
+++ b/arch/mips/loongson2ef/lemote-2f/irq.c
@@ -0,0 +1,117 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2007 Lemote Inc.
+ * Author: Fuxin Zhang, zhangfx@lemote.com
+ */
+
+#include <linux/export.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+
+#include <asm/irq_cpu.h>
+#include <asm/i8259.h>
+#include <asm/mipsregs.h>
+
+#include <loongson.h>
+#include <machine.h>
+
+#define LOONGSON_TIMER_IRQ	(MIPS_CPU_IRQ_BASE + 7) /* cpu timer */
+#define LOONGSON_NORTH_BRIDGE_IRQ	(MIPS_CPU_IRQ_BASE + 6) /* bonito */
+#define LOONGSON_UART_IRQ	(MIPS_CPU_IRQ_BASE + 3) /* cpu serial port */
+#define LOONGSON_SOUTH_BRIDGE_IRQ	(MIPS_CPU_IRQ_BASE + 2) /* i8259 */
+
+#define LOONGSON_INT_BIT_INT0		(1 << 11)
+#define LOONGSON_INT_BIT_INT1		(1 << 12)
+
+/*
+ * The generic i8259_irq() make the kernel hang on booting.  Since we cannot
+ * get the irq via the IRR directly, we access the ISR instead.
+ */
+int mach_i8259_irq(void)
+{
+	int irq, isr;
+
+	irq = -1;
+
+	if ((LOONGSON_INTISR & LOONGSON_INTEN) & LOONGSON_INT_BIT_INT0) {
+		raw_spin_lock(&i8259A_lock);
+		isr = inb(PIC_MASTER_CMD) &
+			~inb(PIC_MASTER_IMR) & ~(1 << PIC_CASCADE_IR);
+		if (!isr)
+			isr = (inb(PIC_SLAVE_CMD) & ~inb(PIC_SLAVE_IMR)) << 8;
+		irq = ffs(isr) - 1;
+		if (unlikely(irq == 7)) {
+			/*
+			 * This may be a spurious interrupt.
+			 *
+			 * Read the interrupt status register (ISR). If the most
+			 * significant bit is not set then there is no valid
+			 * interrupt.
+			 */
+			outb(0x0B, PIC_MASTER_ISR);	/* ISR register */
+			if (~inb(PIC_MASTER_ISR) & 0x80)
+				irq = -1;
+		}
+		raw_spin_unlock(&i8259A_lock);
+	}
+
+	return irq;
+}
+EXPORT_SYMBOL(mach_i8259_irq);
+
+static void i8259_irqdispatch(void)
+{
+	int irq;
+
+	irq = mach_i8259_irq();
+	if (irq >= 0)
+		do_IRQ(irq);
+	else
+		spurious_interrupt();
+}
+
+void mach_irq_dispatch(unsigned int pending)
+{
+	if (pending & CAUSEF_IP7)
+		do_IRQ(LOONGSON_TIMER_IRQ);
+	else if (pending & CAUSEF_IP6) {	/* North Bridge, Perf counter */
+		bonito_irqdispatch();
+	} else if (pending & CAUSEF_IP3)	/* CPU UART */
+		do_IRQ(LOONGSON_UART_IRQ);
+	else if (pending & CAUSEF_IP2)	/* South Bridge */
+		i8259_irqdispatch();
+	else
+		spurious_interrupt();
+}
+
+static irqreturn_t ip6_action(int cpl, void *dev_id)
+{
+	return IRQ_HANDLED;
+}
+
+void __init mach_init_irq(void)
+{
+	/* init all controller
+	 *   0-15	  ------> i8259 interrupt
+	 *   16-23	  ------> mips cpu interrupt
+	 *   32-63	  ------> bonito irq
+	 */
+
+	/* setup cs5536 as high level trigger */
+	LOONGSON_INTPOL = LOONGSON_INT_BIT_INT0 | LOONGSON_INT_BIT_INT1;
+	LOONGSON_INTEDGE &= ~(LOONGSON_INT_BIT_INT0 | LOONGSON_INT_BIT_INT1);
+
+	/* Sets the first-level interrupt dispatcher. */
+	mips_cpu_irq_init();
+	init_i8259_irqs();
+	bonito_irq_init();
+
+	/* setup north bridge irq (bonito) */
+	if (request_irq(LOONGSON_NORTH_BRIDGE_IRQ, ip6_action,
+			IRQF_SHARED | IRQF_NO_THREAD, "cascade", ip6_action))
+		pr_err("Failed to register north bridge cascade interrupt\n");
+	/* setup source bridge irq (i8259) */
+	if (request_irq(LOONGSON_SOUTH_BRIDGE_IRQ, no_action,
+			IRQF_NO_THREAD | IRQF_NO_SUSPEND, "cascade", NULL))
+		pr_err("Failed to register south bridge cascade interrupt\n");
+}
diff --git a/arch/mips/loongson2ef/lemote-2f/machtype.c b/arch/mips/loongson2ef/lemote-2f/machtype.c
new file mode 100644
index 000000000..9462a3ab5
--- /dev/null
+++ b/arch/mips/loongson2ef/lemote-2f/machtype.c
@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2009 Lemote Inc.
+ * Author: Wu Zhangjin, wuzhangjin@gmail.com
+ */
+#include <asm/bootinfo.h>
+
+#include <loongson.h>
+
+void __init mach_prom_init_machtype(void)
+{
+	/* We share the same kernel image file among Lemote 2F family
+	 * of machines, and provide the machtype= kernel command line
+	 * to users to indicate their machine, this command line will
+	 * be passed by the latest PMON automatically. and fortunately,
+	 * up to now, we can get the machine type from the PMON_VER=
+	 * commandline directly except the NAS machine, In the old
+	 * machines, this will help the users a lot.
+	 *
+	 * If no "machtype=" passed, get machine type from "PMON_VER=".
+	 *	PMON_VER=LM8089		Lemote 8.9'' netbook
+	 *		 LM8101		Lemote 10.1'' netbook
+	 *	(The above two netbooks have the same kernel support)
+	 *		 LM6XXX		Lemote FuLoong(2F) box series
+	 *		 LM9XXX		Lemote LynLoong PC series
+	 */
+	if (strstr(arcs_cmdline, "PMON_VER=LM")) {
+		if (strstr(arcs_cmdline, "PMON_VER=LM8"))
+			mips_machtype = MACH_LEMOTE_YL2F89;
+		else if (strstr(arcs_cmdline, "PMON_VER=LM6"))
+			mips_machtype = MACH_LEMOTE_FL2F;
+		else if (strstr(arcs_cmdline, "PMON_VER=LM9"))
+			mips_machtype = MACH_LEMOTE_LL2F;
+		else
+			mips_machtype = MACH_LEMOTE_NAS;
+
+		strcat(arcs_cmdline, " machtype=");
+		strcat(arcs_cmdline, get_system_type());
+		strcat(arcs_cmdline, " ");
+	}
+}
diff --git a/arch/mips/loongson2ef/lemote-2f/pm.c b/arch/mips/loongson2ef/lemote-2f/pm.c
new file mode 100644
index 000000000..3d0027229
--- /dev/null
+++ b/arch/mips/loongson2ef/lemote-2f/pm.c
@@ -0,0 +1,145 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *  Lemote loongson2f family machines' specific suspend support
+ *
+ *  Copyright (C) 2009 Lemote Inc.
+ *  Author: Wu Zhangjin <wuzhangjin@gmail.com>
+ */
+
+#include <linux/suspend.h>
+#include <linux/interrupt.h>
+#include <linux/pm.h>
+#include <linux/i8042.h>
+#include <linux/export.h>
+
+#include <asm/i8259.h>
+#include <asm/mipsregs.h>
+#include <asm/bootinfo.h>
+
+#include <loongson.h>
+
+#include <cs5536/cs5536_mfgpt.h>
+#include "ec_kb3310b.h"
+
+#define I8042_KBD_IRQ		1
+#define I8042_CTR_KBDINT	0x01
+#define I8042_CTR_KBDDIS	0x10
+
+static unsigned char i8042_ctr;
+
+static int i8042_enable_kbd_port(void)
+{
+	if (i8042_command(&i8042_ctr, I8042_CMD_CTL_RCTR)) {
+		pr_err("i8042.c: Can't read CTR while enabling i8042 kbd port."
+		       "\n");
+		return -EIO;
+	}
+
+	i8042_ctr &= ~I8042_CTR_KBDDIS;
+	i8042_ctr |= I8042_CTR_KBDINT;
+
+	if (i8042_command(&i8042_ctr, I8042_CMD_CTL_WCTR)) {
+		i8042_ctr &= ~I8042_CTR_KBDINT;
+		i8042_ctr |= I8042_CTR_KBDDIS;
+		pr_err("i8042.c: Failed to enable KBD port.\n");
+
+		return -EIO;
+	}
+
+	return 0;
+}
+
+void setup_wakeup_events(void)
+{
+	int irq_mask;
+
+	switch (mips_machtype) {
+	case MACH_LEMOTE_ML2F7:
+	case MACH_LEMOTE_YL2F89:
+		/* open the keyboard irq in i8259A */
+		outb((0xff & ~(1 << I8042_KBD_IRQ)), PIC_MASTER_IMR);
+		irq_mask = inb(PIC_MASTER_IMR);
+
+		/* enable keyboard port */
+		i8042_enable_kbd_port();
+
+		/* Wakeup CPU via SCI lid open event */
+		outb(irq_mask & ~(1 << PIC_CASCADE_IR), PIC_MASTER_IMR);
+		inb(PIC_MASTER_IMR);
+		outb(0xff & ~(1 << (SCI_IRQ_NUM - 8)), PIC_SLAVE_IMR);
+		inb(PIC_SLAVE_IMR);
+
+		break;
+
+	default:
+		break;
+	}
+}
+
+static struct delayed_work lid_task;
+static int initialized;
+/* yeeloong_report_lid_status will be implemented in yeeloong_laptop.c */
+sci_handler yeeloong_report_lid_status;
+EXPORT_SYMBOL(yeeloong_report_lid_status);
+static void yeeloong_lid_update_task(struct work_struct *work)
+{
+	if (yeeloong_report_lid_status)
+		yeeloong_report_lid_status(BIT_LID_DETECT_ON);
+}
+
+int wakeup_loongson(void)
+{
+	int irq;
+
+	/* query the interrupt number */
+	irq = mach_i8259_irq();
+	if (irq < 0)
+		return 0;
+
+	printk(KERN_INFO "%s: irq = %d\n", __func__, irq);
+
+	if (irq == I8042_KBD_IRQ)
+		return 1;
+	else if (irq == SCI_IRQ_NUM) {
+		int ret, sci_event;
+		/* query the event number */
+		ret = ec_query_seq(CMD_GET_EVENT_NUM);
+		if (ret < 0)
+			return 0;
+		sci_event = ec_get_event_num();
+		if (sci_event < 0)
+			return 0;
+		if (sci_event == EVENT_LID) {
+			int lid_status;
+			/* check the LID status */
+			lid_status = ec_read(REG_LID_DETECT);
+			/* wakeup cpu when people open the LID */
+			if (lid_status == BIT_LID_DETECT_ON) {
+				/* If we call it directly here, the WARNING
+				 * will be sent out by getnstimeofday
+				 * via "WARN_ON(timekeeping_suspended);"
+				 * because we can not schedule in suspend mode.
+				 */
+				if (initialized == 0) {
+					INIT_DELAYED_WORK(&lid_task,
+						yeeloong_lid_update_task);
+					initialized = 1;
+				}
+				schedule_delayed_work(&lid_task, 1);
+				return 1;
+			}
+		}
+	}
+
+	return 0;
+}
+
+void __weak mach_suspend(void)
+{
+	disable_mfgpt0_counter();
+}
+
+void __weak mach_resume(void)
+{
+	enable_mfgpt0_counter();
+}
diff --git a/arch/mips/loongson2ef/lemote-2f/reset.c b/arch/mips/loongson2ef/lemote-2f/reset.c
new file mode 100644
index 000000000..197dae4ff
--- /dev/null
+++ b/arch/mips/loongson2ef/lemote-2f/reset.c
@@ -0,0 +1,155 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/* Board-specific reboot/shutdown routines
+ *
+ * Copyright (c) 2009 Philippe Vachon <philippe@cowpig.ca>
+ *
+ * Copyright (C) 2009 Lemote Inc.
+ * Author: Wu Zhangjin, wuzhangjin@gmail.com
+ */
+
+#include <linux/io.h>
+#include <linux/delay.h>
+#include <linux/types.h>
+
+#include <asm/bootinfo.h>
+
+#include <loongson.h>
+
+#include <cs5536/cs5536.h>
+#include "ec_kb3310b.h"
+
+static void reset_cpu(void)
+{
+	/*
+	 * reset cpu to full speed, this is needed when enabling cpu frequency
+	 * scalling
+	 */
+	writel(readl(LOONGSON_CHIPCFG) | 0x7, LOONGSON_CHIPCFG);
+}
+
+/* reset support for fuloong2f */
+
+static void fl2f_reboot(void)
+{
+	reset_cpu();
+
+	/* send a reset signal to south bridge.
+	 *
+	 * NOTE: if enable "Power Management" in kernel, rtl8169 will not reset
+	 * normally with this reset operation and it will not work in PMON, but
+	 * you can type halt command and then reboot, seems the hardware reset
+	 * logic not work normally.
+	 */
+	{
+		u32 hi, lo;
+		_rdmsr(DIVIL_MSR_REG(DIVIL_SOFT_RESET), &hi, &lo);
+		lo |= 0x00000001;
+		_wrmsr(DIVIL_MSR_REG(DIVIL_SOFT_RESET), hi, lo);
+	}
+}
+
+static void fl2f_shutdown(void)
+{
+	u32 hi, lo, val;
+	int gpio_base;
+
+	/* get gpio base */
+	_rdmsr(DIVIL_MSR_REG(DIVIL_LBAR_GPIO), &hi, &lo);
+	gpio_base = lo & 0xff00;
+
+	/* make cs5536 gpio13 output enable */
+	val = inl(gpio_base + GPIOL_OUT_EN);
+	val &= ~(1 << (16 + 13));
+	val |= (1 << 13);
+	outl(val, gpio_base + GPIOL_OUT_EN);
+	mmiowb();
+	/* make cs5536 gpio13 output low level voltage. */
+	val = inl(gpio_base + GPIOL_OUT_VAL) & ~(1 << (13));
+	val |= (1 << (16 + 13));
+	outl(val, gpio_base + GPIOL_OUT_VAL);
+	mmiowb();
+}
+
+/* reset support for yeeloong2f and mengloong2f notebook */
+
+static void ml2f_reboot(void)
+{
+	reset_cpu();
+
+	/* sending an reset signal to EC(embedded controller) */
+	ec_write(REG_RESET, BIT_RESET_ON);
+}
+
+#define yl2f89_reboot ml2f_reboot
+
+/* menglong(7inches) laptop has different shutdown logic from 8.9inches */
+#define EC_SHUTDOWN_IO_PORT_HIGH 0xff2d
+#define EC_SHUTDOWN_IO_PORT_LOW	 0xff2e
+#define EC_SHUTDOWN_IO_PORT_DATA 0xff2f
+#define REG_SHUTDOWN_HIGH	 0xFC
+#define REG_SHUTDOWN_LOW	 0x29
+#define BIT_SHUTDOWN_ON		 (1 << 1)
+
+static void ml2f_shutdown(void)
+{
+	u8 val;
+	u64 i;
+
+	outb(REG_SHUTDOWN_HIGH, EC_SHUTDOWN_IO_PORT_HIGH);
+	outb(REG_SHUTDOWN_LOW, EC_SHUTDOWN_IO_PORT_LOW);
+	mmiowb();
+	val = inb(EC_SHUTDOWN_IO_PORT_DATA);
+	outb(val & (~BIT_SHUTDOWN_ON), EC_SHUTDOWN_IO_PORT_DATA);
+	mmiowb();
+	/* need enough wait here... how many microseconds needs? */
+	for (i = 0; i < 0x10000; i++)
+		delay();
+	outb(val | BIT_SHUTDOWN_ON, EC_SHUTDOWN_IO_PORT_DATA);
+	mmiowb();
+}
+
+static void yl2f89_shutdown(void)
+{
+	/* cpu-gpio0 output low */
+	LOONGSON_GPIODATA &= ~0x00000001;
+	/* cpu-gpio0 as output */
+	LOONGSON_GPIOIE &= ~0x00000001;
+}
+
+void mach_prepare_reboot(void)
+{
+	switch (mips_machtype) {
+	case MACH_LEMOTE_FL2F:
+	case MACH_LEMOTE_NAS:
+	case MACH_LEMOTE_LL2F:
+		fl2f_reboot();
+		break;
+	case MACH_LEMOTE_ML2F7:
+		ml2f_reboot();
+		break;
+	case MACH_LEMOTE_YL2F89:
+		yl2f89_reboot();
+		break;
+	default:
+		break;
+	}
+}
+
+void mach_prepare_shutdown(void)
+{
+	switch (mips_machtype) {
+	case MACH_LEMOTE_FL2F:
+	case MACH_LEMOTE_NAS:
+	case MACH_LEMOTE_LL2F:
+		fl2f_shutdown();
+		break;
+	case MACH_LEMOTE_ML2F7:
+		ml2f_shutdown();
+		break;
+	case MACH_LEMOTE_YL2F89:
+		yl2f89_shutdown();
+		break;
+	default:
+		break;
+	}
+}
diff --git a/arch/mips/loongson32/Kconfig b/arch/mips/loongson32/Kconfig
new file mode 100644
index 000000000..2ef9da001
--- /dev/null
+++ b/arch/mips/loongson32/Kconfig
@@ -0,0 +1,75 @@
+# SPDX-License-Identifier: GPL-2.0
+if MACH_LOONGSON32
+
+choice
+	prompt "Machine Type"
+
+config LOONGSON1_LS1B
+	bool "Loongson LS1B board"
+	select CEVT_R4K if !MIPS_EXTERNAL_TIMER
+	select CSRC_R4K if !MIPS_EXTERNAL_TIMER
+	select SYS_HAS_CPU_LOONGSON1B
+	select DMA_NONCOHERENT
+	select BOOT_ELF32
+	select IRQ_MIPS_CPU
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_SUPPORTS_HIGHMEM
+	select SYS_HAS_EARLY_PRINTK
+	select USE_GENERIC_EARLY_PRINTK_8250
+	select COMMON_CLK
+
+config LOONGSON1_LS1C
+	bool "Loongson LS1C board"
+	select CEVT_R4K if !MIPS_EXTERNAL_TIMER
+	select CSRC_R4K if !MIPS_EXTERNAL_TIMER
+	select SYS_HAS_CPU_LOONGSON1C
+	select DMA_NONCOHERENT
+	select BOOT_ELF32
+	select IRQ_MIPS_CPU
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_SUPPORTS_HIGHMEM
+	select SYS_HAS_EARLY_PRINTK
+	select USE_GENERIC_EARLY_PRINTK_8250
+	select COMMON_CLK
+endchoice
+
+menuconfig CEVT_CSRC_LS1X
+	bool "Use PWM Timer for clockevent/clocksource"
+	select MIPS_EXTERNAL_TIMER
+	depends on CPU_LOONGSON32
+	help
+	  This option changes the default clockevent/clocksource to PWM Timer,
+	  and is required by Loongson1 CPUFreq support.
+
+	  If unsure, say N.
+
+choice
+	prompt "Select clockevent/clocksource"
+	depends on CEVT_CSRC_LS1X
+	default TIMER_USE_PWM0
+
+config TIMER_USE_PWM0
+	bool "Use PWM Timer 0"
+	help
+	  Use PWM Timer 0 as the default clockevent/clocksourcer.
+
+config TIMER_USE_PWM1
+	bool "Use PWM Timer 1"
+	help
+	  Use PWM Timer 1 as the default clockevent/clocksourcer.
+
+config TIMER_USE_PWM2
+	bool "Use PWM Timer 2"
+	help
+	  Use PWM Timer 2 as the default clockevent/clocksourcer.
+
+config TIMER_USE_PWM3
+	bool "Use PWM Timer 3"
+	help
+	  Use PWM Timer 3 as the default clockevent/clocksourcer.
+
+endchoice
+
+endif # MACH_LOONGSON32
diff --git a/arch/mips/loongson32/Makefile b/arch/mips/loongson32/Makefile
new file mode 100644
index 000000000..ba10954b4
--- /dev/null
+++ b/arch/mips/loongson32/Makefile
@@ -0,0 +1,18 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Common code for all Loongson 1 based systems
+#
+
+obj-$(CONFIG_MACH_LOONGSON32) += common/
+
+#
+# Loongson LS1B board
+#
+
+obj-$(CONFIG_LOONGSON1_LS1B)  += ls1b/
+
+#
+# Loongson LS1C board
+#
+
+obj-$(CONFIG_LOONGSON1_LS1C)  += ls1c/
diff --git a/arch/mips/loongson32/Platform b/arch/mips/loongson32/Platform
new file mode 100644
index 000000000..3b9673e7a
--- /dev/null
+++ b/arch/mips/loongson32/Platform
@@ -0,0 +1,3 @@
+cflags-$(CONFIG_CPU_LOONGSON32)		+= -march=mips32r2 -Wa,--trap
+cflags-$(CONFIG_MACH_LOONGSON32)	+= -I$(srctree)/arch/mips/include/asm/mach-loongson32
+load-$(CONFIG_CPU_LOONGSON32)		+= 0xffffffff80200000
diff --git a/arch/mips/loongson32/common/Makefile b/arch/mips/loongson32/common/Makefile
new file mode 100644
index 000000000..7b49c8260
--- /dev/null
+++ b/arch/mips/loongson32/common/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Makefile for common code of loongson1 based machines.
+#
+
+obj-y	+= time.o irq.o platform.o prom.o reset.o setup.o
diff --git a/arch/mips/loongson32/common/irq.c b/arch/mips/loongson32/common/irq.c
new file mode 100644
index 000000000..9a50070f7
--- /dev/null
+++ b/arch/mips/loongson32/common/irq.c
@@ -0,0 +1,191 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2011 Zhang, Keguang <keguang.zhang@gmail.com>
+ */
+
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <asm/irq_cpu.h>
+
+#include <loongson1.h>
+#include <irq.h>
+
+#define LS1X_INTC_REG(n, x) \
+		((void __iomem *)KSEG1ADDR(LS1X_INTC_BASE + (n * 0x18) + (x)))
+
+#define LS1X_INTC_INTISR(n)		LS1X_INTC_REG(n, 0x0)
+#define LS1X_INTC_INTIEN(n)		LS1X_INTC_REG(n, 0x4)
+#define LS1X_INTC_INTSET(n)		LS1X_INTC_REG(n, 0x8)
+#define LS1X_INTC_INTCLR(n)		LS1X_INTC_REG(n, 0xc)
+#define LS1X_INTC_INTPOL(n)		LS1X_INTC_REG(n, 0x10)
+#define LS1X_INTC_INTEDGE(n)		LS1X_INTC_REG(n, 0x14)
+
+static void ls1x_irq_ack(struct irq_data *d)
+{
+	unsigned int bit = (d->irq - LS1X_IRQ_BASE) & 0x1f;
+	unsigned int n = (d->irq - LS1X_IRQ_BASE) >> 5;
+
+	__raw_writel(__raw_readl(LS1X_INTC_INTCLR(n))
+			| (1 << bit), LS1X_INTC_INTCLR(n));
+}
+
+static void ls1x_irq_mask(struct irq_data *d)
+{
+	unsigned int bit = (d->irq - LS1X_IRQ_BASE) & 0x1f;
+	unsigned int n = (d->irq - LS1X_IRQ_BASE) >> 5;
+
+	__raw_writel(__raw_readl(LS1X_INTC_INTIEN(n))
+			& ~(1 << bit), LS1X_INTC_INTIEN(n));
+}
+
+static void ls1x_irq_mask_ack(struct irq_data *d)
+{
+	unsigned int bit = (d->irq - LS1X_IRQ_BASE) & 0x1f;
+	unsigned int n = (d->irq - LS1X_IRQ_BASE) >> 5;
+
+	__raw_writel(__raw_readl(LS1X_INTC_INTIEN(n))
+			& ~(1 << bit), LS1X_INTC_INTIEN(n));
+	__raw_writel(__raw_readl(LS1X_INTC_INTCLR(n))
+			| (1 << bit), LS1X_INTC_INTCLR(n));
+}
+
+static void ls1x_irq_unmask(struct irq_data *d)
+{
+	unsigned int bit = (d->irq - LS1X_IRQ_BASE) & 0x1f;
+	unsigned int n = (d->irq - LS1X_IRQ_BASE) >> 5;
+
+	__raw_writel(__raw_readl(LS1X_INTC_INTIEN(n))
+			| (1 << bit), LS1X_INTC_INTIEN(n));
+}
+
+static int ls1x_irq_settype(struct irq_data *d, unsigned int type)
+{
+	unsigned int bit = (d->irq - LS1X_IRQ_BASE) & 0x1f;
+	unsigned int n = (d->irq - LS1X_IRQ_BASE) >> 5;
+
+	switch (type) {
+	case IRQ_TYPE_LEVEL_HIGH:
+		__raw_writel(__raw_readl(LS1X_INTC_INTPOL(n))
+			| (1 << bit), LS1X_INTC_INTPOL(n));
+		__raw_writel(__raw_readl(LS1X_INTC_INTEDGE(n))
+			& ~(1 << bit), LS1X_INTC_INTEDGE(n));
+		break;
+	case IRQ_TYPE_LEVEL_LOW:
+		__raw_writel(__raw_readl(LS1X_INTC_INTPOL(n))
+			& ~(1 << bit), LS1X_INTC_INTPOL(n));
+		__raw_writel(__raw_readl(LS1X_INTC_INTEDGE(n))
+			& ~(1 << bit), LS1X_INTC_INTEDGE(n));
+		break;
+	case IRQ_TYPE_EDGE_RISING:
+		__raw_writel(__raw_readl(LS1X_INTC_INTPOL(n))
+			| (1 << bit), LS1X_INTC_INTPOL(n));
+		__raw_writel(__raw_readl(LS1X_INTC_INTEDGE(n))
+			| (1 << bit), LS1X_INTC_INTEDGE(n));
+		break;
+	case IRQ_TYPE_EDGE_FALLING:
+		__raw_writel(__raw_readl(LS1X_INTC_INTPOL(n))
+			& ~(1 << bit), LS1X_INTC_INTPOL(n));
+		__raw_writel(__raw_readl(LS1X_INTC_INTEDGE(n))
+			| (1 << bit), LS1X_INTC_INTEDGE(n));
+		break;
+	case IRQ_TYPE_EDGE_BOTH:
+		__raw_writel(__raw_readl(LS1X_INTC_INTPOL(n))
+			& ~(1 << bit), LS1X_INTC_INTPOL(n));
+		__raw_writel(__raw_readl(LS1X_INTC_INTEDGE(n))
+			| (1 << bit), LS1X_INTC_INTEDGE(n));
+		break;
+	case IRQ_TYPE_NONE:
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static struct irq_chip ls1x_irq_chip = {
+	.name		= "LS1X-INTC",
+	.irq_ack	= ls1x_irq_ack,
+	.irq_mask	= ls1x_irq_mask,
+	.irq_mask_ack	= ls1x_irq_mask_ack,
+	.irq_unmask	= ls1x_irq_unmask,
+	.irq_set_type   = ls1x_irq_settype,
+};
+
+static void ls1x_irq_dispatch(int n)
+{
+	u32 int_status, irq;
+
+	/* Get pending sources, masked by current enables */
+	int_status = __raw_readl(LS1X_INTC_INTISR(n)) &
+			__raw_readl(LS1X_INTC_INTIEN(n));
+
+	if (int_status) {
+		irq = LS1X_IRQ(n, __ffs(int_status));
+		do_IRQ(irq);
+	}
+}
+
+asmlinkage void plat_irq_dispatch(void)
+{
+	unsigned int pending;
+
+	pending = read_c0_cause() & read_c0_status() & ST0_IM;
+
+	if (pending & CAUSEF_IP7)
+		do_IRQ(TIMER_IRQ);
+	else if (pending & CAUSEF_IP2)
+		ls1x_irq_dispatch(0); /* INT0 */
+	else if (pending & CAUSEF_IP3)
+		ls1x_irq_dispatch(1); /* INT1 */
+	else if (pending & CAUSEF_IP4)
+		ls1x_irq_dispatch(2); /* INT2 */
+	else if (pending & CAUSEF_IP5)
+		ls1x_irq_dispatch(3); /* INT3 */
+	else if (pending & CAUSEF_IP6)
+		ls1x_irq_dispatch(4); /* INT4 */
+	else
+		spurious_interrupt();
+
+}
+
+static void __init ls1x_irq_init(int base)
+{
+	int n;
+
+	/* Disable interrupts and clear pending,
+	 * setup all IRQs as high level triggered
+	 */
+	for (n = 0; n < INTN; n++) {
+		__raw_writel(0x0, LS1X_INTC_INTIEN(n));
+		__raw_writel(0xffffffff, LS1X_INTC_INTCLR(n));
+		__raw_writel(0xffffffff, LS1X_INTC_INTPOL(n));
+		/* set DMA0, DMA1 and DMA2 to edge trigger */
+		__raw_writel(n ? 0x0 : 0xe000, LS1X_INTC_INTEDGE(n));
+	}
+
+
+	for (n = base; n < NR_IRQS; n++) {
+		irq_set_chip_and_handler(n, &ls1x_irq_chip,
+					 handle_level_irq);
+	}
+
+	if (request_irq(INT0_IRQ, no_action, IRQF_NO_THREAD, "cascade", NULL))
+		pr_err("Failed to request irq %d (cascade)\n", INT0_IRQ);
+	if (request_irq(INT1_IRQ, no_action, IRQF_NO_THREAD, "cascade", NULL))
+		pr_err("Failed to request irq %d (cascade)\n", INT1_IRQ);
+	if (request_irq(INT2_IRQ, no_action, IRQF_NO_THREAD, "cascade", NULL))
+		pr_err("Failed to request irq %d (cascade)\n", INT2_IRQ);
+	if (request_irq(INT3_IRQ, no_action, IRQF_NO_THREAD, "cascade", NULL))
+		pr_err("Failed to request irq %d (cascade)\n", INT3_IRQ);
+#if defined(CONFIG_LOONGSON1_LS1C)
+	if (request_irq(INT4_IRQ, no_action, IRQF_NO_THREAD, "cascade", NULL))
+		pr_err("Failed to request irq %d (cascade)\n", INT4_IRQ);
+#endif
+}
+
+void __init arch_init_irq(void)
+{
+	mips_cpu_irq_init();
+	ls1x_irq_init(LS1X_IRQ_BASE);
+}
diff --git a/arch/mips/loongson32/common/platform.c b/arch/mips/loongson32/common/platform.c
new file mode 100644
index 000000000..311dc1580
--- /dev/null
+++ b/arch/mips/loongson32/common/platform.c
@@ -0,0 +1,311 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2011-2016 Zhang, Keguang <keguang.zhang@gmail.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/dma-mapping.h>
+#include <linux/err.h>
+#include <linux/mtd/partitions.h>
+#include <linux/sizes.h>
+#include <linux/phy.h>
+#include <linux/serial_8250.h>
+#include <linux/stmmac.h>
+#include <linux/usb/ehci_pdriver.h>
+
+#include <platform.h>
+#include <loongson1.h>
+#include <cpufreq.h>
+#include <dma.h>
+#include <nand.h>
+
+/* 8250/16550 compatible UART */
+#define LS1X_UART(_id)						\
+	{							\
+		.mapbase	= LS1X_UART ## _id ## _BASE,	\
+		.irq		= LS1X_UART ## _id ## _IRQ,	\
+		.iotype		= UPIO_MEM,			\
+		.flags		= UPF_IOREMAP | UPF_FIXED_TYPE, \
+		.type		= PORT_16550A,			\
+	}
+
+static struct plat_serial8250_port ls1x_serial8250_pdata[] = {
+	LS1X_UART(0),
+	LS1X_UART(1),
+	LS1X_UART(2),
+	LS1X_UART(3),
+	{},
+};
+
+struct platform_device ls1x_uart_pdev = {
+	.name		= "serial8250",
+	.id		= PLAT8250_DEV_PLATFORM,
+	.dev		= {
+		.platform_data = ls1x_serial8250_pdata,
+	},
+};
+
+void __init ls1x_serial_set_uartclk(struct platform_device *pdev)
+{
+	struct clk *clk;
+	struct plat_serial8250_port *p;
+
+	clk = clk_get(&pdev->dev, pdev->name);
+	if (IS_ERR(clk)) {
+		pr_err("unable to get %s clock, err=%ld",
+		       pdev->name, PTR_ERR(clk));
+		return;
+	}
+	clk_prepare_enable(clk);
+
+	for (p = pdev->dev.platform_data; p->flags != 0; ++p)
+		p->uartclk = clk_get_rate(clk);
+}
+
+/* CPUFreq */
+static struct plat_ls1x_cpufreq ls1x_cpufreq_pdata = {
+	.clk_name	= "cpu_clk",
+	.osc_clk_name	= "osc_clk",
+	.max_freq	= 266 * 1000,
+	.min_freq	= 33 * 1000,
+};
+
+struct platform_device ls1x_cpufreq_pdev = {
+	.name		= "ls1x-cpufreq",
+	.dev		= {
+		.platform_data = &ls1x_cpufreq_pdata,
+	},
+};
+
+/* Synopsys Ethernet GMAC */
+static struct stmmac_mdio_bus_data ls1x_mdio_bus_data = {
+	.phy_mask	= 0,
+};
+
+static struct stmmac_dma_cfg ls1x_eth_dma_cfg = {
+	.pbl		= 1,
+};
+
+int ls1x_eth_mux_init(struct platform_device *pdev, void *priv)
+{
+	struct plat_stmmacenet_data *plat_dat = NULL;
+	u32 val;
+
+	val = __raw_readl(LS1X_MUX_CTRL1);
+
+#if defined(CONFIG_LOONGSON1_LS1B)
+	plat_dat = dev_get_platdata(&pdev->dev);
+	if (plat_dat->bus_id) {
+		__raw_writel(__raw_readl(LS1X_MUX_CTRL0) | GMAC1_USE_UART1 |
+			     GMAC1_USE_UART0, LS1X_MUX_CTRL0);
+		switch (plat_dat->phy_interface) {
+		case PHY_INTERFACE_MODE_RGMII:
+			val &= ~(GMAC1_USE_TXCLK | GMAC1_USE_PWM23);
+			break;
+		case PHY_INTERFACE_MODE_MII:
+			val |= (GMAC1_USE_TXCLK | GMAC1_USE_PWM23);
+			break;
+		default:
+			pr_err("unsupported mii mode %d\n",
+			       plat_dat->phy_interface);
+			return -ENOTSUPP;
+		}
+		val &= ~GMAC1_SHUT;
+	} else {
+		switch (plat_dat->phy_interface) {
+		case PHY_INTERFACE_MODE_RGMII:
+			val &= ~(GMAC0_USE_TXCLK | GMAC0_USE_PWM01);
+			break;
+		case PHY_INTERFACE_MODE_MII:
+			val |= (GMAC0_USE_TXCLK | GMAC0_USE_PWM01);
+			break;
+		default:
+			pr_err("unsupported mii mode %d\n",
+			       plat_dat->phy_interface);
+			return -ENOTSUPP;
+		}
+		val &= ~GMAC0_SHUT;
+	}
+	__raw_writel(val, LS1X_MUX_CTRL1);
+#elif defined(CONFIG_LOONGSON1_LS1C)
+	plat_dat = dev_get_platdata(&pdev->dev);
+
+	val &= ~PHY_INTF_SELI;
+	if (plat_dat->phy_interface == PHY_INTERFACE_MODE_RMII)
+		val |= 0x4 << PHY_INTF_SELI_SHIFT;
+	__raw_writel(val, LS1X_MUX_CTRL1);
+
+	val = __raw_readl(LS1X_MUX_CTRL0);
+	__raw_writel(val & (~GMAC_SHUT), LS1X_MUX_CTRL0);
+#endif
+
+	return 0;
+}
+
+static struct plat_stmmacenet_data ls1x_eth0_pdata = {
+	.bus_id			= 0,
+	.phy_addr		= -1,
+#if defined(CONFIG_LOONGSON1_LS1B)
+	.phy_interface		= PHY_INTERFACE_MODE_MII,
+#elif defined(CONFIG_LOONGSON1_LS1C)
+	.phy_interface		= PHY_INTERFACE_MODE_RMII,
+#endif
+	.mdio_bus_data		= &ls1x_mdio_bus_data,
+	.dma_cfg		= &ls1x_eth_dma_cfg,
+	.has_gmac		= 1,
+	.tx_coe			= 1,
+	.rx_queues_to_use	= 1,
+	.tx_queues_to_use	= 1,
+	.init			= ls1x_eth_mux_init,
+};
+
+static struct resource ls1x_eth0_resources[] = {
+	[0] = {
+		.start	= LS1X_GMAC0_BASE,
+		.end	= LS1X_GMAC0_BASE + SZ_64K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.name	= "macirq",
+		.start	= LS1X_GMAC0_IRQ,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+struct platform_device ls1x_eth0_pdev = {
+	.name		= "stmmaceth",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(ls1x_eth0_resources),
+	.resource	= ls1x_eth0_resources,
+	.dev		= {
+		.platform_data = &ls1x_eth0_pdata,
+	},
+};
+
+#ifdef CONFIG_LOONGSON1_LS1B
+static struct plat_stmmacenet_data ls1x_eth1_pdata = {
+	.bus_id			= 1,
+	.phy_addr		= -1,
+	.phy_interface		= PHY_INTERFACE_MODE_MII,
+	.mdio_bus_data		= &ls1x_mdio_bus_data,
+	.dma_cfg		= &ls1x_eth_dma_cfg,
+	.has_gmac		= 1,
+	.tx_coe			= 1,
+	.rx_queues_to_use	= 1,
+	.tx_queues_to_use	= 1,
+	.init			= ls1x_eth_mux_init,
+};
+
+static struct resource ls1x_eth1_resources[] = {
+	[0] = {
+		.start	= LS1X_GMAC1_BASE,
+		.end	= LS1X_GMAC1_BASE + SZ_64K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.name	= "macirq",
+		.start	= LS1X_GMAC1_IRQ,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+struct platform_device ls1x_eth1_pdev = {
+	.name		= "stmmaceth",
+	.id		= 1,
+	.num_resources	= ARRAY_SIZE(ls1x_eth1_resources),
+	.resource	= ls1x_eth1_resources,
+	.dev		= {
+		.platform_data = &ls1x_eth1_pdata,
+	},
+};
+#endif	/* CONFIG_LOONGSON1_LS1B */
+
+/* GPIO */
+static struct resource ls1x_gpio0_resources[] = {
+	[0] = {
+		.start	= LS1X_GPIO0_BASE,
+		.end	= LS1X_GPIO0_BASE + SZ_4 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+struct platform_device ls1x_gpio0_pdev = {
+	.name		= "ls1x-gpio",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(ls1x_gpio0_resources),
+	.resource	= ls1x_gpio0_resources,
+};
+
+static struct resource ls1x_gpio1_resources[] = {
+	[0] = {
+		.start	= LS1X_GPIO1_BASE,
+		.end	= LS1X_GPIO1_BASE + SZ_4 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+struct platform_device ls1x_gpio1_pdev = {
+	.name		= "ls1x-gpio",
+	.id		= 1,
+	.num_resources	= ARRAY_SIZE(ls1x_gpio1_resources),
+	.resource	= ls1x_gpio1_resources,
+};
+
+/* USB EHCI */
+static u64 ls1x_ehci_dmamask = DMA_BIT_MASK(32);
+
+static struct resource ls1x_ehci_resources[] = {
+	[0] = {
+		.start	= LS1X_EHCI_BASE,
+		.end	= LS1X_EHCI_BASE + SZ_32K - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= LS1X_EHCI_IRQ,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct usb_ehci_pdata ls1x_ehci_pdata = {
+};
+
+struct platform_device ls1x_ehci_pdev = {
+	.name		= "ehci-platform",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(ls1x_ehci_resources),
+	.resource	= ls1x_ehci_resources,
+	.dev		= {
+		.dma_mask = &ls1x_ehci_dmamask,
+		.platform_data = &ls1x_ehci_pdata,
+	},
+};
+
+/* Real Time Clock */
+void __init ls1x_rtc_set_extclk(struct platform_device *pdev)
+{
+	u32 val = __raw_readl(LS1X_RTC_CTRL);
+
+	if (!(val & RTC_EXTCLK_OK))
+		__raw_writel(val | RTC_EXTCLK_EN, LS1X_RTC_CTRL);
+}
+
+struct platform_device ls1x_rtc_pdev = {
+	.name		= "ls1x-rtc",
+	.id		= -1,
+};
+
+/* Watchdog */
+static struct resource ls1x_wdt_resources[] = {
+	{
+		.start	= LS1X_WDT_BASE,
+		.end	= LS1X_WDT_BASE + SZ_16 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+struct platform_device ls1x_wdt_pdev = {
+	.name		= "ls1x-wdt",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(ls1x_wdt_resources),
+	.resource	= ls1x_wdt_resources,
+};
diff --git a/arch/mips/loongson32/common/prom.c b/arch/mips/loongson32/common/prom.c
new file mode 100644
index 000000000..fc580a227
--- /dev/null
+++ b/arch/mips/loongson32/common/prom.c
@@ -0,0 +1,42 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2011 Zhang, Keguang <keguang.zhang@gmail.com>
+ *
+ * Modified from arch/mips/pnx833x/common/prom.c.
+ */
+
+#include <linux/io.h>
+#include <linux/init.h>
+#include <linux/memblock.h>
+#include <linux/serial_reg.h>
+#include <asm/fw/fw.h>
+
+#include <loongson1.h>
+
+unsigned long memsize;
+
+void __init prom_init(void)
+{
+	void __iomem *uart_base;
+
+	fw_init_cmdline();
+
+	memsize = fw_getenvl("memsize");
+	if(!memsize)
+		memsize = DEFAULT_MEMSIZE;
+
+	if (strstr(arcs_cmdline, "console=ttyS3"))
+		uart_base = ioremap(LS1X_UART3_BASE, 0x0f);
+	else if (strstr(arcs_cmdline, "console=ttyS2"))
+		uart_base = ioremap(LS1X_UART2_BASE, 0x0f);
+	else if (strstr(arcs_cmdline, "console=ttyS1"))
+		uart_base = ioremap(LS1X_UART1_BASE, 0x0f);
+	else
+		uart_base = ioremap(LS1X_UART0_BASE, 0x0f);
+	setup_8250_early_printk_port((unsigned long)uart_base, 0, 0);
+}
+
+void __init plat_mem_setup(void)
+{
+	memblock_add(0x0, (memsize << 20));
+}
diff --git a/arch/mips/loongson32/common/reset.c b/arch/mips/loongson32/common/reset.c
new file mode 100644
index 000000000..0c7399b30
--- /dev/null
+++ b/arch/mips/loongson32/common/reset.c
@@ -0,0 +1,51 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2011 Zhang, Keguang <keguang.zhang@gmail.com>
+ */
+
+#include <linux/io.h>
+#include <linux/pm.h>
+#include <linux/sizes.h>
+#include <asm/idle.h>
+#include <asm/reboot.h>
+
+#include <loongson1.h>
+
+static void __iomem *wdt_reg_base;
+
+static void ls1x_halt(void)
+{
+	while (1) {
+		if (cpu_wait)
+			cpu_wait();
+	}
+}
+
+static void ls1x_restart(char *command)
+{
+	__raw_writel(0x1, wdt_reg_base + WDT_EN);
+	__raw_writel(0x1, wdt_reg_base + WDT_TIMER);
+	__raw_writel(0x1, wdt_reg_base + WDT_SET);
+
+	ls1x_halt();
+}
+
+static void ls1x_power_off(void)
+{
+	ls1x_halt();
+}
+
+static int __init ls1x_reboot_setup(void)
+{
+	wdt_reg_base = ioremap(LS1X_WDT_BASE, (SZ_4 + SZ_8));
+	if (!wdt_reg_base)
+		panic("Failed to remap watchdog registers");
+
+	_machine_restart = ls1x_restart;
+	_machine_halt = ls1x_halt;
+	pm_power_off = ls1x_power_off;
+
+	return 0;
+}
+
+arch_initcall(ls1x_reboot_setup);
diff --git a/arch/mips/loongson32/common/setup.c b/arch/mips/loongson32/common/setup.c
new file mode 100644
index 000000000..4733fe037
--- /dev/null
+++ b/arch/mips/loongson32/common/setup.c
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2011 Zhang, Keguang <keguang.zhang@gmail.com>
+ */
+
+#include <linux/io.h>
+#include <linux/init.h>
+#include <linux/smp.h>
+#include <asm/cpu-info.h>
+#include <asm/bootinfo.h>
+
+const char *get_system_type(void)
+{
+	unsigned int processor_id = (&current_cpu_data)->processor_id;
+
+	switch (processor_id & PRID_REV_MASK) {
+	case PRID_REV_LOONGSON1B:
+#if defined(CONFIG_LOONGSON1_LS1B)
+		return "LOONGSON LS1B";
+#elif defined(CONFIG_LOONGSON1_LS1C)
+		return "LOONGSON LS1C";
+#endif
+	default:
+		return "LOONGSON (unknown)";
+	}
+}
diff --git a/arch/mips/loongson32/common/time.c b/arch/mips/loongson32/common/time.c
new file mode 100644
index 000000000..459b15c96
--- /dev/null
+++ b/arch/mips/loongson32/common/time.c
@@ -0,0 +1,232 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2014 Zhang, Keguang <keguang.zhang@gmail.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/interrupt.h>
+#include <linux/sizes.h>
+#include <asm/time.h>
+
+#include <loongson1.h>
+#include <platform.h>
+
+#ifdef CONFIG_CEVT_CSRC_LS1X
+
+#if defined(CONFIG_TIMER_USE_PWM1)
+#define LS1X_TIMER_BASE	LS1X_PWM1_BASE
+#define LS1X_TIMER_IRQ	LS1X_PWM1_IRQ
+
+#elif defined(CONFIG_TIMER_USE_PWM2)
+#define LS1X_TIMER_BASE	LS1X_PWM2_BASE
+#define LS1X_TIMER_IRQ	LS1X_PWM2_IRQ
+
+#elif defined(CONFIG_TIMER_USE_PWM3)
+#define LS1X_TIMER_BASE	LS1X_PWM3_BASE
+#define LS1X_TIMER_IRQ	LS1X_PWM3_IRQ
+
+#else
+#define LS1X_TIMER_BASE	LS1X_PWM0_BASE
+#define LS1X_TIMER_IRQ	LS1X_PWM0_IRQ
+#endif
+
+DEFINE_RAW_SPINLOCK(ls1x_timer_lock);
+
+static void __iomem *timer_reg_base;
+static uint32_t ls1x_jiffies_per_tick;
+
+static inline void ls1x_pwmtimer_set_period(uint32_t period)
+{
+	__raw_writel(period, timer_reg_base + PWM_HRC);
+	__raw_writel(period, timer_reg_base + PWM_LRC);
+}
+
+static inline void ls1x_pwmtimer_restart(void)
+{
+	__raw_writel(0x0, timer_reg_base + PWM_CNT);
+	__raw_writel(INT_EN | CNT_EN, timer_reg_base + PWM_CTRL);
+}
+
+void __init ls1x_pwmtimer_init(void)
+{
+	timer_reg_base = ioremap(LS1X_TIMER_BASE, SZ_16);
+	if (!timer_reg_base)
+		panic("Failed to remap timer registers");
+
+	ls1x_jiffies_per_tick = DIV_ROUND_CLOSEST(mips_hpt_frequency, HZ);
+
+	ls1x_pwmtimer_set_period(ls1x_jiffies_per_tick);
+	ls1x_pwmtimer_restart();
+}
+
+static u64 ls1x_clocksource_read(struct clocksource *cs)
+{
+	unsigned long flags;
+	int count;
+	u32 jifs;
+	static int old_count;
+	static u32 old_jifs;
+
+	raw_spin_lock_irqsave(&ls1x_timer_lock, flags);
+	/*
+	 * Although our caller may have the read side of xtime_lock,
+	 * this is now a seqlock, and we are cheating in this routine
+	 * by having side effects on state that we cannot undo if
+	 * there is a collision on the seqlock and our caller has to
+	 * retry.  (Namely, old_jifs and old_count.)  So we must treat
+	 * jiffies as volatile despite the lock.  We read jiffies
+	 * before latching the timer count to guarantee that although
+	 * the jiffies value might be older than the count (that is,
+	 * the counter may underflow between the last point where
+	 * jiffies was incremented and the point where we latch the
+	 * count), it cannot be newer.
+	 */
+	jifs = jiffies;
+	/* read the count */
+	count = __raw_readl(timer_reg_base + PWM_CNT);
+
+	/*
+	 * It's possible for count to appear to go the wrong way for this
+	 * reason:
+	 *
+	 *  The timer counter underflows, but we haven't handled the resulting
+	 *  interrupt and incremented jiffies yet.
+	 *
+	 * Previous attempts to handle these cases intelligently were buggy, so
+	 * we just do the simple thing now.
+	 */
+	if (count < old_count && jifs == old_jifs)
+		count = old_count;
+
+	old_count = count;
+	old_jifs = jifs;
+
+	raw_spin_unlock_irqrestore(&ls1x_timer_lock, flags);
+
+	return (u64) (jifs * ls1x_jiffies_per_tick) + count;
+}
+
+static struct clocksource ls1x_clocksource = {
+	.name		= "ls1x-pwmtimer",
+	.read		= ls1x_clocksource_read,
+	.mask		= CLOCKSOURCE_MASK(24),
+	.flags		= CLOCK_SOURCE_IS_CONTINUOUS,
+};
+
+static irqreturn_t ls1x_clockevent_isr(int irq, void *devid)
+{
+	struct clock_event_device *cd = devid;
+
+	ls1x_pwmtimer_restart();
+	cd->event_handler(cd);
+
+	return IRQ_HANDLED;
+}
+
+static int ls1x_clockevent_set_state_periodic(struct clock_event_device *cd)
+{
+	raw_spin_lock(&ls1x_timer_lock);
+	ls1x_pwmtimer_set_period(ls1x_jiffies_per_tick);
+	ls1x_pwmtimer_restart();
+	__raw_writel(INT_EN | CNT_EN, timer_reg_base + PWM_CTRL);
+	raw_spin_unlock(&ls1x_timer_lock);
+
+	return 0;
+}
+
+static int ls1x_clockevent_tick_resume(struct clock_event_device *cd)
+{
+	raw_spin_lock(&ls1x_timer_lock);
+	__raw_writel(INT_EN | CNT_EN, timer_reg_base + PWM_CTRL);
+	raw_spin_unlock(&ls1x_timer_lock);
+
+	return 0;
+}
+
+static int ls1x_clockevent_set_state_shutdown(struct clock_event_device *cd)
+{
+	raw_spin_lock(&ls1x_timer_lock);
+	__raw_writel(__raw_readl(timer_reg_base + PWM_CTRL) & ~CNT_EN,
+		     timer_reg_base + PWM_CTRL);
+	raw_spin_unlock(&ls1x_timer_lock);
+
+	return 0;
+}
+
+static int ls1x_clockevent_set_next(unsigned long evt,
+				    struct clock_event_device *cd)
+{
+	raw_spin_lock(&ls1x_timer_lock);
+	ls1x_pwmtimer_set_period(evt);
+	ls1x_pwmtimer_restart();
+	raw_spin_unlock(&ls1x_timer_lock);
+
+	return 0;
+}
+
+static struct clock_event_device ls1x_clockevent = {
+	.name			= "ls1x-pwmtimer",
+	.features		= CLOCK_EVT_FEAT_PERIODIC,
+	.rating			= 300,
+	.irq			= LS1X_TIMER_IRQ,
+	.set_next_event		= ls1x_clockevent_set_next,
+	.set_state_shutdown	= ls1x_clockevent_set_state_shutdown,
+	.set_state_periodic	= ls1x_clockevent_set_state_periodic,
+	.set_state_oneshot	= ls1x_clockevent_set_state_shutdown,
+	.tick_resume		= ls1x_clockevent_tick_resume,
+};
+
+static void __init ls1x_time_init(void)
+{
+	struct clock_event_device *cd = &ls1x_clockevent;
+	int ret;
+
+	if (!mips_hpt_frequency)
+		panic("Invalid timer clock rate");
+
+	ls1x_pwmtimer_init();
+
+	clockevent_set_clock(cd, mips_hpt_frequency);
+	cd->max_delta_ns = clockevent_delta2ns(0xffffff, cd);
+	cd->max_delta_ticks = 0xffffff;
+	cd->min_delta_ns = clockevent_delta2ns(0x000300, cd);
+	cd->min_delta_ticks = 0x000300;
+	cd->cpumask = cpumask_of(smp_processor_id());
+	clockevents_register_device(cd);
+
+	ls1x_clocksource.rating = 200 + mips_hpt_frequency / 10000000;
+	ret = clocksource_register_hz(&ls1x_clocksource, mips_hpt_frequency);
+	if (ret)
+		panic(KERN_ERR "Failed to register clocksource: %d\n", ret);
+
+	if (request_irq(LS1X_TIMER_IRQ, ls1x_clockevent_isr,
+			IRQF_PERCPU | IRQF_TIMER, "ls1x-pwmtimer",
+			&ls1x_clockevent))
+		pr_err("Failed to register ls1x-pwmtimer interrupt\n");
+}
+#endif /* CONFIG_CEVT_CSRC_LS1X */
+
+void __init plat_time_init(void)
+{
+	struct clk *clk = NULL;
+
+	/* initialize LS1X clocks */
+	ls1x_clk_init();
+
+#ifdef CONFIG_CEVT_CSRC_LS1X
+	/* setup LS1X PWM timer */
+	clk = clk_get(NULL, "ls1x-pwmtimer");
+	if (IS_ERR(clk))
+		panic("unable to get timer clock, err=%ld", PTR_ERR(clk));
+
+	mips_hpt_frequency = clk_get_rate(clk);
+	ls1x_time_init();
+#else
+	/* setup mips r4k timer */
+	clk = clk_get(NULL, "cpu_clk");
+	if (IS_ERR(clk))
+		panic("unable to get cpu clock, err=%ld", PTR_ERR(clk));
+
+	mips_hpt_frequency = clk_get_rate(clk) / 2;
+#endif /* CONFIG_CEVT_CSRC_LS1X */
+}
diff --git a/arch/mips/loongson32/ls1b/Makefile b/arch/mips/loongson32/ls1b/Makefile
new file mode 100644
index 000000000..33c574dc0
--- /dev/null
+++ b/arch/mips/loongson32/ls1b/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Makefile for loongson1B based machines.
+#
+
+obj-y += board.o
diff --git a/arch/mips/loongson32/ls1b/board.c b/arch/mips/loongson32/ls1b/board.c
new file mode 100644
index 000000000..727e06718
--- /dev/null
+++ b/arch/mips/loongson32/ls1b/board.c
@@ -0,0 +1,58 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2011-2016 Zhang, Keguang <keguang.zhang@gmail.com>
+ */
+
+#include <linux/leds.h>
+#include <linux/mtd/partitions.h>
+#include <linux/sizes.h>
+
+#include <loongson1.h>
+#include <dma.h>
+#include <nand.h>
+#include <platform.h>
+
+static const struct gpio_led ls1x_gpio_leds[] __initconst = {
+	{
+		.name			= "LED9",
+		.default_trigger	= "heartbeat",
+		.gpio			= 38,
+		.active_low		= 1,
+		.default_state		= LEDS_GPIO_DEFSTATE_OFF,
+	}, {
+		.name			= "LED6",
+		.default_trigger	= "nand-disk",
+		.gpio			= 39,
+		.active_low		= 1,
+		.default_state		= LEDS_GPIO_DEFSTATE_OFF,
+	},
+};
+
+static const struct gpio_led_platform_data ls1x_led_pdata __initconst = {
+	.num_leds	= ARRAY_SIZE(ls1x_gpio_leds),
+	.leds		= ls1x_gpio_leds,
+};
+
+static struct platform_device *ls1b_platform_devices[] __initdata = {
+	&ls1x_uart_pdev,
+	&ls1x_cpufreq_pdev,
+	&ls1x_eth0_pdev,
+	&ls1x_eth1_pdev,
+	&ls1x_ehci_pdev,
+	&ls1x_gpio0_pdev,
+	&ls1x_gpio1_pdev,
+	&ls1x_rtc_pdev,
+	&ls1x_wdt_pdev,
+};
+
+static int __init ls1b_platform_init(void)
+{
+	ls1x_serial_set_uartclk(&ls1x_uart_pdev);
+
+	gpio_led_register_device(-1, &ls1x_led_pdata);
+
+	return platform_add_devices(ls1b_platform_devices,
+				   ARRAY_SIZE(ls1b_platform_devices));
+}
+
+arch_initcall(ls1b_platform_init);
diff --git a/arch/mips/loongson32/ls1c/Makefile b/arch/mips/loongson32/ls1c/Makefile
new file mode 100644
index 000000000..1cf3aa264
--- /dev/null
+++ b/arch/mips/loongson32/ls1c/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Makefile for loongson1C based machines.
+#
+
+obj-y += board.o
diff --git a/arch/mips/loongson32/ls1c/board.c b/arch/mips/loongson32/ls1c/board.c
new file mode 100644
index 000000000..9dcfe9de5
--- /dev/null
+++ b/arch/mips/loongson32/ls1c/board.c
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2016 Yang Ling <gnaygnil@gmail.com>
+ */
+
+#include <platform.h>
+
+static struct platform_device *ls1c_platform_devices[] __initdata = {
+	&ls1x_uart_pdev,
+	&ls1x_eth0_pdev,
+	&ls1x_rtc_pdev,
+	&ls1x_wdt_pdev,
+};
+
+static int __init ls1c_platform_init(void)
+{
+	ls1x_serial_set_uartclk(&ls1x_uart_pdev);
+
+	return platform_add_devices(ls1c_platform_devices,
+				   ARRAY_SIZE(ls1c_platform_devices));
+}
+
+arch_initcall(ls1c_platform_init);
diff --git a/arch/mips/loongson64/Kconfig b/arch/mips/loongson64/Kconfig
new file mode 100644
index 000000000..517f1f8e8
--- /dev/null
+++ b/arch/mips/loongson64/Kconfig
@@ -0,0 +1,15 @@
+# SPDX-License-Identifier: GPL-2.0
+if MACH_LOONGSON64
+
+config RS780_HPET
+	bool "RS780/SBX00 HPET Timer"
+	depends on MACH_LOONGSON64
+	depends on BROKEN
+	select MIPS_EXTERNAL_TIMER
+	help
+	  This option enables the hpet timer of AMD RS780/SBX00.
+
+	  Note: This driver is doing some dangerous hack. Please only enable
+	  it on RS780E systems.
+
+endif # MACH_LOONGSON64
diff --git a/arch/mips/loongson64/Makefile b/arch/mips/loongson64/Makefile
new file mode 100644
index 000000000..e806280bb
--- /dev/null
+++ b/arch/mips/loongson64/Makefile
@@ -0,0 +1,14 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Makefile for Loongson-3 family machines
+#
+obj-$(CONFIG_MACH_LOONGSON64) += cop2-ex.o dma.o \
+				setup.o init.o env.o time.o reset.o \
+
+obj-$(CONFIG_SMP)	+= smp.o
+obj-$(CONFIG_NUMA)	+= numa.o
+obj-$(CONFIG_RS780_HPET) += hpet.o
+obj-$(CONFIG_SUSPEND) += pm.o
+obj-$(CONFIG_PCI_QUIRKS) += vbios_quirk.o
+obj-$(CONFIG_CPU_LOONGSON3_CPUCFG_EMULATION) += cpucfg-emul.o
+obj-$(CONFIG_SYSFS) += boardinfo.o
diff --git a/arch/mips/loongson64/Platform b/arch/mips/loongson64/Platform
new file mode 100644
index 000000000..49c9889e3
--- /dev/null
+++ b/arch/mips/loongson64/Platform
@@ -0,0 +1,7 @@
+#
+# Loongson Machines' Support
+#
+
+cflags-$(CONFIG_MACH_LOONGSON64) += -I$(srctree)/arch/mips/include/asm/mach-loongson64
+cflags-$(CONFIG_CC_HAS_MNO_BRANCH_LIKELY) += -mno-branch-likely
+load-$(CONFIG_CPU_LOONGSON64) += 0xffffffff80200000
diff --git a/arch/mips/loongson64/boardinfo.c b/arch/mips/loongson64/boardinfo.c
new file mode 100644
index 000000000..280989c5a
--- /dev/null
+++ b/arch/mips/loongson64/boardinfo.c
@@ -0,0 +1,48 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/kobject.h>
+#include <boot_param.h>
+
+static ssize_t boardinfo_show(struct kobject *kobj,
+			      struct kobj_attribute *attr, char *buf)
+{
+	char board_manufacturer[64] = {0};
+	char *tmp_board_manufacturer = board_manufacturer;
+	char bios_vendor[64] = {0};
+	char *tmp_bios_vendor = bios_vendor;
+
+	strcpy(board_manufacturer, eboard->name);
+	strcpy(bios_vendor, einter->description);
+
+	return sprintf(buf,
+		       "Board Info\n"
+		       "Manufacturer\t\t: %s\n"
+		       "Board Name\t\t: %s\n"
+		       "Family\t\t\t: LOONGSON3\n\n"
+		       "BIOS Info\n"
+		       "Vendor\t\t\t: %s\n"
+		       "Version\t\t\t: %s\n"
+		       "ROM Size\t\t: %d KB\n"
+		       "Release Date\t\t: %s\n",
+		       strsep(&tmp_board_manufacturer, "-"),
+		       eboard->name,
+		       strsep(&tmp_bios_vendor, "-"),
+		       einter->description,
+		       einter->size,
+		       especial->special_name);
+}
+static struct kobj_attribute boardinfo_attr = __ATTR(boardinfo, 0444,
+						     boardinfo_show, NULL);
+
+static int __init boardinfo_init(void)
+{
+	struct kobject *lefi_kobj;
+
+	lefi_kobj = kobject_create_and_add("lefi", firmware_kobj);
+	if (!lefi_kobj) {
+		pr_err("lefi: Firmware registration failed.\n");
+		return -ENOMEM;
+	}
+
+	return sysfs_create_file(lefi_kobj, &boardinfo_attr.attr);
+}
+late_initcall(boardinfo_init);
diff --git a/arch/mips/loongson64/cop2-ex.c b/arch/mips/loongson64/cop2-ex.c
new file mode 100644
index 000000000..00055d4b6
--- /dev/null
+++ b/arch/mips/loongson64/cop2-ex.c
@@ -0,0 +1,341 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2014 Lemote Corporation.
+ *   written by Huacai Chen <chenhc@lemote.com>
+ *
+ * based on arch/mips/cavium-octeon/cpu.c
+ * Copyright (C) 2009 Wind River Systems,
+ *   written by Ralf Baechle <ralf@linux-mips.org>
+ */
+#include <linux/init.h>
+#include <linux/sched.h>
+#include <linux/notifier.h>
+#include <linux/ptrace.h>
+#include <linux/uaccess.h>
+#include <linux/sched/signal.h>
+
+#include <asm/fpu.h>
+#include <asm/cop2.h>
+#include <asm/inst.h>
+#include <asm/branch.h>
+#include <asm/current.h>
+#include <asm/mipsregs.h>
+#include <asm/unaligned-emul.h>
+
+static int loongson_cu2_call(struct notifier_block *nfb, unsigned long action,
+	void *data)
+{
+	unsigned int res, fpu_owned;
+	unsigned long ra, value, value_next;
+	union mips_instruction insn;
+	int fr = !test_thread_flag(TIF_32BIT_FPREGS);
+	struct pt_regs *regs = (struct pt_regs *)data;
+	void __user *addr = (void __user *)regs->cp0_badvaddr;
+	unsigned int __user *pc = (unsigned int __user *)exception_epc(regs);
+
+	ra = regs->regs[31];
+	__get_user(insn.word, pc);
+
+	switch (action) {
+	case CU2_EXCEPTION:
+		preempt_disable();
+		fpu_owned = __is_fpu_owner();
+		if (!fr)
+			set_c0_status(ST0_CU1 | ST0_CU2);
+		else
+			set_c0_status(ST0_CU1 | ST0_CU2 | ST0_FR);
+		enable_fpu_hazard();
+		KSTK_STATUS(current) |= (ST0_CU1 | ST0_CU2);
+		if (fr)
+			KSTK_STATUS(current) |= ST0_FR;
+		else
+			KSTK_STATUS(current) &= ~ST0_FR;
+		/* If FPU is owned, we needn't init or restore fp */
+		if (!fpu_owned) {
+			set_thread_flag(TIF_USEDFPU);
+			init_fp_ctx(current);
+			_restore_fp(current);
+		}
+		preempt_enable();
+
+		return NOTIFY_STOP;	/* Don't call default notifier */
+
+	case CU2_LWC2_OP:
+		if (insn.loongson3_lswc2_format.ls == 0)
+			goto sigbus;
+
+		if (insn.loongson3_lswc2_format.fr == 0) {	/* gslq */
+			if (!access_ok(addr, 16))
+				goto sigbus;
+
+			LoadDW(addr, value, res);
+			if (res)
+				goto fault;
+
+			LoadDW(addr + 8, value_next, res);
+			if (res)
+				goto fault;
+
+			regs->regs[insn.loongson3_lswc2_format.rt] = value;
+			regs->regs[insn.loongson3_lswc2_format.rq] = value_next;
+			compute_return_epc(regs);
+		} else {					/* gslqc1 */
+			if (!access_ok(addr, 16))
+				goto sigbus;
+
+			lose_fpu(1);
+			LoadDW(addr, value, res);
+			if (res)
+				goto fault;
+
+			LoadDW(addr + 8, value_next, res);
+			if (res)
+				goto fault;
+
+			set_fpr64(&current->thread.fpu.fpr[insn.loongson3_lswc2_format.rt], 0, value);
+			set_fpr64(&current->thread.fpu.fpr[insn.loongson3_lswc2_format.rq], 0, value_next);
+			compute_return_epc(regs);
+			own_fpu(1);
+		}
+		return NOTIFY_STOP;	/* Don't call default notifier */
+
+	case CU2_SWC2_OP:
+		if (insn.loongson3_lswc2_format.ls == 0)
+			goto sigbus;
+
+		if (insn.loongson3_lswc2_format.fr == 0) {	/* gssq */
+			if (!access_ok(addr, 16))
+				goto sigbus;
+
+			/* write upper 8 bytes first */
+			value_next = regs->regs[insn.loongson3_lswc2_format.rq];
+
+			StoreDW(addr + 8, value_next, res);
+			if (res)
+				goto fault;
+			value = regs->regs[insn.loongson3_lswc2_format.rt];
+
+			StoreDW(addr, value, res);
+			if (res)
+				goto fault;
+
+			compute_return_epc(regs);
+		} else {					/* gssqc1 */
+			if (!access_ok(addr, 16))
+				goto sigbus;
+
+			lose_fpu(1);
+			value_next = get_fpr64(&current->thread.fpu.fpr[insn.loongson3_lswc2_format.rq], 0);
+
+			StoreDW(addr + 8, value_next, res);
+			if (res)
+				goto fault;
+
+			value = get_fpr64(&current->thread.fpu.fpr[insn.loongson3_lswc2_format.rt], 0);
+
+			StoreDW(addr, value, res);
+			if (res)
+				goto fault;
+
+			compute_return_epc(regs);
+			own_fpu(1);
+		}
+		return NOTIFY_STOP;	/* Don't call default notifier */
+
+	case CU2_LDC2_OP:
+		switch (insn.loongson3_lsdc2_format.opcode1) {
+		/*
+		 * Loongson-3 overridden ldc2 instructions.
+		 * opcode1              instruction
+		 *   0x1          gslhx: load 2 bytes to GPR
+		 *   0x2          gslwx: load 4 bytes to GPR
+		 *   0x3          gsldx: load 8 bytes to GPR
+		 *   0x6	  gslwxc1: load 4 bytes to FPR
+		 *   0x7	  gsldxc1: load 8 bytes to FPR
+		 */
+		case 0x1:
+			if (!access_ok(addr, 2))
+				goto sigbus;
+
+			LoadHW(addr, value, res);
+			if (res)
+				goto fault;
+
+			compute_return_epc(regs);
+			regs->regs[insn.loongson3_lsdc2_format.rt] = value;
+			break;
+		case 0x2:
+			if (!access_ok(addr, 4))
+				goto sigbus;
+
+			LoadW(addr, value, res);
+			if (res)
+				goto fault;
+
+			compute_return_epc(regs);
+			regs->regs[insn.loongson3_lsdc2_format.rt] = value;
+			break;
+		case 0x3:
+			if (!access_ok(addr, 8))
+				goto sigbus;
+
+			LoadDW(addr, value, res);
+			if (res)
+				goto fault;
+
+			compute_return_epc(regs);
+			regs->regs[insn.loongson3_lsdc2_format.rt] = value;
+			break;
+		case 0x6:
+			die_if_kernel("Unaligned FP access in kernel code", regs);
+			BUG_ON(!used_math());
+			if (!access_ok(addr, 4))
+				goto sigbus;
+
+			lose_fpu(1);
+			LoadW(addr, value, res);
+			if (res)
+				goto fault;
+
+			set_fpr64(&current->thread.fpu.fpr[insn.loongson3_lsdc2_format.rt], 0, value);
+			compute_return_epc(regs);
+			own_fpu(1);
+
+			break;
+		case 0x7:
+			die_if_kernel("Unaligned FP access in kernel code", regs);
+			BUG_ON(!used_math());
+			if (!access_ok(addr, 8))
+				goto sigbus;
+
+			lose_fpu(1);
+			LoadDW(addr, value, res);
+			if (res)
+				goto fault;
+
+			set_fpr64(&current->thread.fpu.fpr[insn.loongson3_lsdc2_format.rt], 0, value);
+			compute_return_epc(regs);
+			own_fpu(1);
+			break;
+
+		}
+		return NOTIFY_STOP;	/* Don't call default notifier */
+
+	case CU2_SDC2_OP:
+		switch (insn.loongson3_lsdc2_format.opcode1) {
+		/*
+		 * Loongson-3 overridden sdc2 instructions.
+		 * opcode1              instruction
+		 *   0x1          gsshx: store 2 bytes from GPR
+		 *   0x2          gsswx: store 4 bytes from GPR
+		 *   0x3          gssdx: store 8 bytes from GPR
+		 *   0x6          gsswxc1: store 4 bytes from FPR
+		 *   0x7          gssdxc1: store 8 bytes from FPR
+		 */
+		case 0x1:
+			if (!access_ok(addr, 2))
+				goto sigbus;
+
+			compute_return_epc(regs);
+			value = regs->regs[insn.loongson3_lsdc2_format.rt];
+
+			StoreHW(addr, value, res);
+			if (res)
+				goto fault;
+
+			break;
+		case 0x2:
+			if (!access_ok(addr, 4))
+				goto sigbus;
+
+			compute_return_epc(regs);
+			value = regs->regs[insn.loongson3_lsdc2_format.rt];
+
+			StoreW(addr, value, res);
+			if (res)
+				goto fault;
+
+			break;
+		case 0x3:
+			if (!access_ok(addr, 8))
+				goto sigbus;
+
+			compute_return_epc(regs);
+			value = regs->regs[insn.loongson3_lsdc2_format.rt];
+
+			StoreDW(addr, value, res);
+			if (res)
+				goto fault;
+
+			break;
+
+		case 0x6:
+			die_if_kernel("Unaligned FP access in kernel code", regs);
+			BUG_ON(!used_math());
+
+			if (!access_ok(addr, 4))
+				goto sigbus;
+
+			lose_fpu(1);
+			value = get_fpr64(&current->thread.fpu.fpr[insn.loongson3_lsdc2_format.rt], 0);
+
+			StoreW(addr, value, res);
+			if (res)
+				goto fault;
+
+			compute_return_epc(regs);
+			own_fpu(1);
+
+			break;
+		case 0x7:
+			die_if_kernel("Unaligned FP access in kernel code", regs);
+			BUG_ON(!used_math());
+
+			if (!access_ok(addr, 8))
+				goto sigbus;
+
+			lose_fpu(1);
+			value = get_fpr64(&current->thread.fpu.fpr[insn.loongson3_lsdc2_format.rt], 0);
+
+			StoreDW(addr, value, res);
+			if (res)
+				goto fault;
+
+			compute_return_epc(regs);
+			own_fpu(1);
+
+			break;
+		}
+		return NOTIFY_STOP;	/* Don't call default notifier */
+	}
+
+	return NOTIFY_OK;		/* Let default notifier send signals */
+
+fault:
+	/* roll back jump/branch */
+	regs->regs[31] = ra;
+	regs->cp0_epc = (unsigned long)pc;
+	/* Did we have an exception handler installed? */
+	if (fixup_exception(regs))
+		return NOTIFY_STOP;	/* Don't call default notifier */
+
+	die_if_kernel("Unhandled kernel unaligned access", regs);
+	force_sig(SIGSEGV);
+
+	return NOTIFY_STOP;	/* Don't call default notifier */
+
+sigbus:
+	die_if_kernel("Unhandled kernel unaligned access", regs);
+	force_sig(SIGBUS);
+
+	return NOTIFY_STOP;	/* Don't call default notifier */
+}
+
+static int __init loongson_cu2_setup(void)
+{
+	return cu2_notifier(loongson_cu2_call, 0);
+}
+early_initcall(loongson_cu2_setup);
diff --git a/arch/mips/loongson64/cpucfg-emul.c b/arch/mips/loongson64/cpucfg-emul.c
new file mode 100644
index 000000000..630927e46
--- /dev/null
+++ b/arch/mips/loongson64/cpucfg-emul.c
@@ -0,0 +1,227 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include <linux/smp.h>
+#include <linux/types.h>
+#include <asm/cpu.h>
+#include <asm/cpu-info.h>
+#include <asm/elf.h>
+
+#include <loongson_regs.h>
+#include <cpucfg-emul.h>
+
+static bool is_loongson(struct cpuinfo_mips *c)
+{
+	switch (c->processor_id & PRID_COMP_MASK) {
+	case PRID_COMP_LEGACY:
+		return ((c->processor_id & PRID_IMP_MASK) ==
+			PRID_IMP_LOONGSON_64C);
+
+	case PRID_COMP_LOONGSON:
+		return true;
+
+	default:
+		return false;
+	}
+}
+
+static u32 get_loongson_fprev(struct cpuinfo_mips *c)
+{
+	return c->fpu_id & LOONGSON_FPREV_MASK;
+}
+
+static bool cpu_has_uca(void)
+{
+	u32 diag = read_c0_diag();
+	u32 new_diag;
+
+	if (diag & LOONGSON_DIAG_UCAC)
+		/* UCA is already enabled. */
+		return true;
+
+	/* See if UCAC bit can be flipped on. This should be safe. */
+	new_diag = diag | LOONGSON_DIAG_UCAC;
+	write_c0_diag(new_diag);
+	new_diag = read_c0_diag();
+	write_c0_diag(diag);
+
+	return (new_diag & LOONGSON_DIAG_UCAC) != 0;
+}
+
+static void probe_uca(struct cpuinfo_mips *c)
+{
+	if (cpu_has_uca())
+		c->loongson3_cpucfg_data[0] |= LOONGSON_CFG1_LSUCA;
+}
+
+static void decode_loongson_config6(struct cpuinfo_mips *c)
+{
+	u32 config6 = read_c0_config6();
+
+	if (config6 & LOONGSON_CONF6_SFBEN)
+		c->loongson3_cpucfg_data[0] |= LOONGSON_CFG1_SFBP;
+	if (config6 & LOONGSON_CONF6_LLEXC)
+		c->loongson3_cpucfg_data[0] |= LOONGSON_CFG1_LLEXC;
+	if (config6 & LOONGSON_CONF6_SCRAND)
+		c->loongson3_cpucfg_data[0] |= LOONGSON_CFG1_SCRAND;
+}
+
+static void patch_cpucfg_sel1(struct cpuinfo_mips *c)
+{
+	u64 ases = c->ases;
+	u64 options = c->options;
+	u32 data = c->loongson3_cpucfg_data[0];
+
+	if (options & MIPS_CPU_FPU) {
+		data |= LOONGSON_CFG1_FP;
+		data |= get_loongson_fprev(c) << LOONGSON_CFG1_FPREV_OFFSET;
+	}
+	if (ases & MIPS_ASE_LOONGSON_MMI)
+		data |= LOONGSON_CFG1_MMI;
+	if (ases & MIPS_ASE_MSA)
+		data |= LOONGSON_CFG1_MSA1;
+
+	c->loongson3_cpucfg_data[0] = data;
+}
+
+static void patch_cpucfg_sel2(struct cpuinfo_mips *c)
+{
+	u64 ases = c->ases;
+	u64 options = c->options;
+	u32 data = c->loongson3_cpucfg_data[1];
+
+	if (ases & MIPS_ASE_LOONGSON_EXT)
+		data |= LOONGSON_CFG2_LEXT1;
+	if (ases & MIPS_ASE_LOONGSON_EXT2)
+		data |= LOONGSON_CFG2_LEXT2;
+	if (options & MIPS_CPU_LDPTE)
+		data |= LOONGSON_CFG2_LSPW;
+
+	if (ases & MIPS_ASE_VZ)
+		data |= LOONGSON_CFG2_LVZP;
+	else
+		data &= ~LOONGSON_CFG2_LVZREV;
+
+	c->loongson3_cpucfg_data[1] = data;
+}
+
+static void patch_cpucfg_sel3(struct cpuinfo_mips *c)
+{
+	u64 ases = c->ases;
+	u32 data = c->loongson3_cpucfg_data[2];
+
+	if (ases & MIPS_ASE_LOONGSON_CAM) {
+		data |= LOONGSON_CFG3_LCAMP;
+	} else {
+		data &= ~LOONGSON_CFG3_LCAMREV;
+		data &= ~LOONGSON_CFG3_LCAMNUM;
+		data &= ~LOONGSON_CFG3_LCAMKW;
+		data &= ~LOONGSON_CFG3_LCAMVW;
+	}
+
+	c->loongson3_cpucfg_data[2] = data;
+}
+
+void loongson3_cpucfg_synthesize_data(struct cpuinfo_mips *c)
+{
+	/* Only engage the logic on Loongson processors. */
+	if (!is_loongson(c))
+		return;
+
+	/* CPUs with CPUCFG support don't need to synthesize anything. */
+	if (cpu_has_cfg())
+		goto have_cpucfg_now;
+
+	c->loongson3_cpucfg_data[0] = 0;
+	c->loongson3_cpucfg_data[1] = 0;
+	c->loongson3_cpucfg_data[2] = 0;
+
+	/* Add CPUCFG features non-discoverable otherwise. */
+	switch (c->processor_id & (PRID_IMP_MASK | PRID_REV_MASK)) {
+	case PRID_IMP_LOONGSON_64R | PRID_REV_LOONGSON2K_R1_0:
+	case PRID_IMP_LOONGSON_64R | PRID_REV_LOONGSON2K_R1_1:
+	case PRID_IMP_LOONGSON_64R | PRID_REV_LOONGSON2K_R1_2:
+	case PRID_IMP_LOONGSON_64R | PRID_REV_LOONGSON2K_R1_3:
+		decode_loongson_config6(c);
+		probe_uca(c);
+
+		c->loongson3_cpucfg_data[0] |= (LOONGSON_CFG1_LSLDR0 |
+			LOONGSON_CFG1_LSSYNCI | LOONGSON_CFG1_LLSYNC |
+			LOONGSON_CFG1_TGTSYNC);
+		c->loongson3_cpucfg_data[1] |= (LOONGSON_CFG2_LBT1 |
+			LOONGSON_CFG2_LBT2 | LOONGSON_CFG2_LPMP |
+			LOONGSON_CFG2_LPM_REV2);
+		c->loongson3_cpucfg_data[2] = 0;
+		break;
+
+	case PRID_IMP_LOONGSON_64C | PRID_REV_LOONGSON3A_R1:
+		c->loongson3_cpucfg_data[0] |= (LOONGSON_CFG1_LSLDR0 |
+			LOONGSON_CFG1_LSSYNCI | LOONGSON_CFG1_LSUCA |
+			LOONGSON_CFG1_LLSYNC | LOONGSON_CFG1_TGTSYNC);
+		c->loongson3_cpucfg_data[1] |= (LOONGSON_CFG2_LBT1 |
+			LOONGSON_CFG2_LPMP | LOONGSON_CFG2_LPM_REV1);
+		c->loongson3_cpucfg_data[2] |= (
+			LOONGSON_CFG3_LCAM_REV1 |
+			LOONGSON_CFG3_LCAMNUM_REV1 |
+			LOONGSON_CFG3_LCAMKW_REV1 |
+			LOONGSON_CFG3_LCAMVW_REV1);
+		break;
+
+	case PRID_IMP_LOONGSON_64C | PRID_REV_LOONGSON3B_R1:
+	case PRID_IMP_LOONGSON_64C | PRID_REV_LOONGSON3B_R2:
+		c->loongson3_cpucfg_data[0] |= (LOONGSON_CFG1_LSLDR0 |
+			LOONGSON_CFG1_LSSYNCI | LOONGSON_CFG1_LSUCA |
+			LOONGSON_CFG1_LLSYNC | LOONGSON_CFG1_TGTSYNC);
+		c->loongson3_cpucfg_data[1] |= (LOONGSON_CFG2_LBT1 |
+			LOONGSON_CFG2_LPMP | LOONGSON_CFG2_LPM_REV1);
+		c->loongson3_cpucfg_data[2] |= (
+			LOONGSON_CFG3_LCAM_REV1 |
+			LOONGSON_CFG3_LCAMNUM_REV1 |
+			LOONGSON_CFG3_LCAMKW_REV1 |
+			LOONGSON_CFG3_LCAMVW_REV1);
+		break;
+
+	case PRID_IMP_LOONGSON_64C | PRID_REV_LOONGSON3A_R2_0:
+	case PRID_IMP_LOONGSON_64C | PRID_REV_LOONGSON3A_R2_1:
+	case PRID_IMP_LOONGSON_64C | PRID_REV_LOONGSON3A_R3_0:
+	case PRID_IMP_LOONGSON_64C | PRID_REV_LOONGSON3A_R3_1:
+		decode_loongson_config6(c);
+		probe_uca(c);
+
+		c->loongson3_cpucfg_data[0] |= (LOONGSON_CFG1_CNT64 |
+			LOONGSON_CFG1_LSLDR0 | LOONGSON_CFG1_LSPREF |
+			LOONGSON_CFG1_LSPREFX | LOONGSON_CFG1_LSSYNCI |
+			LOONGSON_CFG1_LLSYNC | LOONGSON_CFG1_TGTSYNC);
+		c->loongson3_cpucfg_data[1] |= (LOONGSON_CFG2_LBT1 |
+			LOONGSON_CFG2_LBT2 | LOONGSON_CFG2_LBTMMU |
+			LOONGSON_CFG2_LPMP | LOONGSON_CFG2_LPM_REV1 |
+			LOONGSON_CFG2_LVZ_REV1);
+		c->loongson3_cpucfg_data[2] |= (LOONGSON_CFG3_LCAM_REV1 |
+			LOONGSON_CFG3_LCAMNUM_REV1 |
+			LOONGSON_CFG3_LCAMKW_REV1 |
+			LOONGSON_CFG3_LCAMVW_REV1);
+		break;
+
+	default:
+		/* It is possible that some future Loongson cores still do
+		 * not have CPUCFG, so do not emulate anything for these
+		 * cores.
+		 */
+		return;
+	}
+
+	/* This feature is set by firmware, but all known Loongson-64 systems
+	 * are configured this way.
+	 */
+	c->loongson3_cpucfg_data[0] |= LOONGSON_CFG1_CDMAP;
+
+	/* Patch in dynamically probed bits. */
+	patch_cpucfg_sel1(c);
+	patch_cpucfg_sel2(c);
+	patch_cpucfg_sel3(c);
+
+have_cpucfg_now:
+	/* We have usable CPUCFG now, emulated or not.
+	 * Announce CPUCFG availability to userspace via hwcap.
+	 */
+	elf_hwcap |= HWCAP_LOONGSON_CPUCFG;
+}
diff --git a/arch/mips/loongson64/dma.c b/arch/mips/loongson64/dma.c
new file mode 100644
index 000000000..8220a1bc0
--- /dev/null
+++ b/arch/mips/loongson64/dma.c
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/dma-direct.h>
+#include <linux/init.h>
+#include <linux/swiotlb.h>
+#include <boot_param.h>
+
+dma_addr_t phys_to_dma(struct device *dev, phys_addr_t paddr)
+{
+	/* We extract 2bit node id (bit 44~47, only bit 44~45 used now) from
+	 * Loongson-3's 48bit address space and embed it into 40bit */
+	long nid = (paddr >> 44) & 0x3;
+
+	return ((nid << 44) ^ paddr) | (nid << node_id_offset);
+}
+
+phys_addr_t dma_to_phys(struct device *dev, dma_addr_t daddr)
+{
+	/* We extract 2bit node id (bit 44~47, only bit 44~45 used now) from
+	 * Loongson-3's 48bit address space and embed it into 40bit */
+	long nid = (daddr >> node_id_offset) & 0x3;
+
+	return ((nid << node_id_offset) ^ daddr) | (nid << 44);
+}
+
+void __init plat_swiotlb_setup(void)
+{
+	swiotlb_init(true, SWIOTLB_VERBOSE);
+}
diff --git a/arch/mips/loongson64/env.c b/arch/mips/loongson64/env.c
new file mode 100644
index 000000000..ef3750a6f
--- /dev/null
+++ b/arch/mips/loongson64/env.c
@@ -0,0 +1,231 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Based on Ocelot Linux port, which is
+ * Copyright 2001 MontaVista Software Inc.
+ * Author: jsun@mvista.com or jsun@junsun.net
+ *
+ * Copyright 2003 ICT CAS
+ * Author: Michael Guo <guoyi@ict.ac.cn>
+ *
+ * Copyright (C) 2007 Lemote Inc. & Institute of Computing Technology
+ * Author: Fuxin Zhang, zhangfx@lemote.com
+ *
+ * Copyright (C) 2009 Lemote Inc.
+ * Author: Wu Zhangjin, wuzhangjin@gmail.com
+ */
+
+#include <linux/dma-map-ops.h>
+#include <linux/export.h>
+#include <linux/pci_ids.h>
+#include <asm/bootinfo.h>
+#include <loongson.h>
+#include <boot_param.h>
+#include <builtin_dtbs.h>
+#include <workarounds.h>
+
+#define HOST_BRIDGE_CONFIG_ADDR	((void __iomem *)TO_UNCAC(0x1a000000))
+
+u32 cpu_clock_freq;
+EXPORT_SYMBOL(cpu_clock_freq);
+struct efi_memory_map_loongson *loongson_memmap;
+struct loongson_system_configuration loongson_sysconf;
+
+struct board_devices *eboard;
+struct interface_info *einter;
+struct loongson_special_attribute *especial;
+
+u64 loongson_chipcfg[MAX_PACKAGES] = {0xffffffffbfc00180};
+u64 loongson_chiptemp[MAX_PACKAGES];
+u64 loongson_freqctrl[MAX_PACKAGES];
+
+unsigned long long smp_group[4];
+
+const char *get_system_type(void)
+{
+	return "Generic Loongson64 System";
+}
+
+
+void __init prom_dtb_init_env(void)
+{
+	if ((fw_arg2 < CKSEG0 || fw_arg2 > CKSEG1)
+		&& (fw_arg2 < XKPHYS || fw_arg2 > XKSEG))
+
+		loongson_fdt_blob = __dtb_loongson64_2core_2k1000_begin;
+	else
+		loongson_fdt_blob = (void *)fw_arg2;
+}
+
+void __init prom_lefi_init_env(void)
+{
+	struct boot_params *boot_p;
+	struct loongson_params *loongson_p;
+	struct system_loongson *esys;
+	struct efi_cpuinfo_loongson *ecpu;
+	struct irq_source_routing_table *eirq_source;
+	u32 id;
+	u16 vendor;
+
+	/* firmware arguments are initialized in head.S */
+	boot_p = (struct boot_params *)fw_arg2;
+	loongson_p = &(boot_p->efi.smbios.lp);
+
+	esys = (struct system_loongson *)
+		((u64)loongson_p + loongson_p->system_offset);
+	ecpu = (struct efi_cpuinfo_loongson *)
+		((u64)loongson_p + loongson_p->cpu_offset);
+	eboard = (struct board_devices *)
+		((u64)loongson_p + loongson_p->boarddev_table_offset);
+	einter = (struct interface_info *)
+		((u64)loongson_p + loongson_p->interface_offset);
+	especial = (struct loongson_special_attribute *)
+		((u64)loongson_p + loongson_p->special_offset);
+	eirq_source = (struct irq_source_routing_table *)
+		((u64)loongson_p + loongson_p->irq_offset);
+	loongson_memmap = (struct efi_memory_map_loongson *)
+		((u64)loongson_p + loongson_p->memory_offset);
+
+	cpu_clock_freq = ecpu->cpu_clock_freq;
+	loongson_sysconf.cputype = ecpu->cputype;
+	switch (ecpu->cputype) {
+	case Legacy_3A:
+	case Loongson_3A:
+		loongson_sysconf.cores_per_node = 4;
+		loongson_sysconf.cores_per_package = 4;
+		smp_group[0] = 0x900000003ff01000;
+		smp_group[1] = 0x900010003ff01000;
+		smp_group[2] = 0x900020003ff01000;
+		smp_group[3] = 0x900030003ff01000;
+		loongson_chipcfg[0] = 0x900000001fe00180;
+		loongson_chipcfg[1] = 0x900010001fe00180;
+		loongson_chipcfg[2] = 0x900020001fe00180;
+		loongson_chipcfg[3] = 0x900030001fe00180;
+		loongson_chiptemp[0] = 0x900000001fe0019c;
+		loongson_chiptemp[1] = 0x900010001fe0019c;
+		loongson_chiptemp[2] = 0x900020001fe0019c;
+		loongson_chiptemp[3] = 0x900030001fe0019c;
+		loongson_freqctrl[0] = 0x900000001fe001d0;
+		loongson_freqctrl[1] = 0x900010001fe001d0;
+		loongson_freqctrl[2] = 0x900020001fe001d0;
+		loongson_freqctrl[3] = 0x900030001fe001d0;
+		loongson_sysconf.workarounds = WORKAROUND_CPUFREQ;
+		break;
+	case Legacy_3B:
+	case Loongson_3B:
+		loongson_sysconf.cores_per_node = 4; /* One chip has 2 nodes */
+		loongson_sysconf.cores_per_package = 8;
+		smp_group[0] = 0x900000003ff01000;
+		smp_group[1] = 0x900010003ff05000;
+		smp_group[2] = 0x900020003ff09000;
+		smp_group[3] = 0x900030003ff0d000;
+		loongson_chipcfg[0] = 0x900000001fe00180;
+		loongson_chipcfg[1] = 0x900020001fe00180;
+		loongson_chipcfg[2] = 0x900040001fe00180;
+		loongson_chipcfg[3] = 0x900060001fe00180;
+		loongson_chiptemp[0] = 0x900000001fe0019c;
+		loongson_chiptemp[1] = 0x900020001fe0019c;
+		loongson_chiptemp[2] = 0x900040001fe0019c;
+		loongson_chiptemp[3] = 0x900060001fe0019c;
+		loongson_freqctrl[0] = 0x900000001fe001d0;
+		loongson_freqctrl[1] = 0x900020001fe001d0;
+		loongson_freqctrl[2] = 0x900040001fe001d0;
+		loongson_freqctrl[3] = 0x900060001fe001d0;
+		loongson_sysconf.workarounds = WORKAROUND_CPUHOTPLUG;
+		break;
+	default:
+		loongson_sysconf.cores_per_node = 1;
+		loongson_sysconf.cores_per_package = 1;
+		loongson_chipcfg[0] = 0x900000001fe00180;
+	}
+
+	loongson_sysconf.nr_cpus = ecpu->nr_cpus;
+	loongson_sysconf.boot_cpu_id = ecpu->cpu_startup_core_id;
+	loongson_sysconf.reserved_cpus_mask = ecpu->reserved_cores_mask;
+	if (ecpu->nr_cpus > NR_CPUS || ecpu->nr_cpus == 0)
+		loongson_sysconf.nr_cpus = NR_CPUS;
+	loongson_sysconf.nr_nodes = (loongson_sysconf.nr_cpus +
+		loongson_sysconf.cores_per_node - 1) /
+		loongson_sysconf.cores_per_node;
+
+	loongson_sysconf.dma_mask_bits = eirq_source->dma_mask_bits;
+	if (loongson_sysconf.dma_mask_bits < 32 ||
+			loongson_sysconf.dma_mask_bits > 64) {
+		loongson_sysconf.dma_mask_bits = 32;
+		dma_default_coherent = true;
+	} else {
+		dma_default_coherent = !eirq_source->dma_noncoherent;
+	}
+
+	pr_info("Firmware: Coherent DMA: %s\n", dma_default_coherent ? "on" : "off");
+
+	loongson_sysconf.restart_addr = boot_p->reset_system.ResetWarm;
+	loongson_sysconf.poweroff_addr = boot_p->reset_system.Shutdown;
+	loongson_sysconf.suspend_addr = boot_p->reset_system.DoSuspend;
+
+	loongson_sysconf.vgabios_addr = boot_p->efi.smbios.vga_bios;
+	pr_debug("Shutdown Addr: %llx, Restart Addr: %llx, VBIOS Addr: %llx\n",
+		loongson_sysconf.poweroff_addr, loongson_sysconf.restart_addr,
+		loongson_sysconf.vgabios_addr);
+
+	loongson_sysconf.workarounds |= esys->workarounds;
+
+	pr_info("CpuClock = %u\n", cpu_clock_freq);
+
+	/* Read the ID of PCI host bridge to detect bridge type */
+	id = readl(HOST_BRIDGE_CONFIG_ADDR);
+	vendor = id & 0xffff;
+
+	switch (vendor) {
+	case PCI_VENDOR_ID_LOONGSON:
+		pr_info("The bridge chip is LS7A\n");
+		loongson_sysconf.bridgetype = LS7A;
+		loongson_sysconf.early_config = ls7a_early_config;
+		break;
+	case PCI_VENDOR_ID_AMD:
+	case PCI_VENDOR_ID_ATI:
+		pr_info("The bridge chip is RS780E or SR5690\n");
+		loongson_sysconf.bridgetype = RS780E;
+		loongson_sysconf.early_config = rs780e_early_config;
+		break;
+	default:
+		pr_info("The bridge chip is VIRTUAL\n");
+		loongson_sysconf.bridgetype = VIRTUAL;
+		loongson_sysconf.early_config = virtual_early_config;
+		loongson_fdt_blob = __dtb_loongson64v_4core_virtio_begin;
+		break;
+	}
+
+	if ((read_c0_prid() & PRID_IMP_MASK) == PRID_IMP_LOONGSON_64C) {
+		switch (read_c0_prid() & PRID_REV_MASK) {
+		case PRID_REV_LOONGSON3A_R1:
+		case PRID_REV_LOONGSON3A_R2_0:
+		case PRID_REV_LOONGSON3A_R2_1:
+		case PRID_REV_LOONGSON3A_R3_0:
+		case PRID_REV_LOONGSON3A_R3_1:
+			switch (loongson_sysconf.bridgetype) {
+			case LS7A:
+				loongson_fdt_blob = __dtb_loongson64c_4core_ls7a_begin;
+				break;
+			case RS780E:
+				loongson_fdt_blob = __dtb_loongson64c_4core_rs780e_begin;
+				break;
+			default:
+				break;
+			}
+			break;
+		case PRID_REV_LOONGSON3B_R1:
+		case PRID_REV_LOONGSON3B_R2:
+			if (loongson_sysconf.bridgetype == RS780E)
+				loongson_fdt_blob = __dtb_loongson64c_8core_rs780e_begin;
+			break;
+		default:
+			break;
+		}
+	} else if ((read_c0_prid() & PRID_IMP_MASK) == PRID_IMP_LOONGSON_64G) {
+		if (loongson_sysconf.bridgetype == LS7A)
+			loongson_fdt_blob = __dtb_loongson64g_4core_ls7a_begin;
+	}
+
+	if (!loongson_fdt_blob)
+		pr_err("Failed to determine built-in Loongson64 dtb\n");
+}
diff --git a/arch/mips/loongson64/hpet.c b/arch/mips/loongson64/hpet.c
new file mode 100644
index 000000000..e42825925
--- /dev/null
+++ b/arch/mips/loongson64/hpet.c
@@ -0,0 +1,285 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/init.h>
+#include <linux/pci.h>
+#include <linux/percpu.h>
+#include <linux/delay.h>
+#include <linux/spinlock.h>
+#include <linux/interrupt.h>
+
+#include <asm/hpet.h>
+#include <asm/time.h>
+
+#define SMBUS_CFG_BASE		(loongson_sysconf.ht_control_base + 0x0300a000)
+#define SMBUS_PCI_REG40		0x40
+#define SMBUS_PCI_REG64		0x64
+#define SMBUS_PCI_REGB4		0xb4
+
+#define HPET_MIN_CYCLES		16
+#define HPET_MIN_PROG_DELTA	(HPET_MIN_CYCLES * 12)
+
+static DEFINE_SPINLOCK(hpet_lock);
+DEFINE_PER_CPU(struct clock_event_device, hpet_clockevent_device);
+
+static unsigned int smbus_read(int offset)
+{
+	return *(volatile unsigned int *)(SMBUS_CFG_BASE + offset);
+}
+
+static void smbus_write(int offset, int data)
+{
+	*(volatile unsigned int *)(SMBUS_CFG_BASE + offset) = data;
+}
+
+static void smbus_enable(int offset, int bit)
+{
+	unsigned int cfg = smbus_read(offset);
+
+	cfg |= bit;
+	smbus_write(offset, cfg);
+}
+
+static int hpet_read(int offset)
+{
+	return *(volatile unsigned int *)(HPET_MMIO_ADDR + offset);
+}
+
+static void hpet_write(int offset, int data)
+{
+	*(volatile unsigned int *)(HPET_MMIO_ADDR + offset) = data;
+}
+
+static void hpet_start_counter(void)
+{
+	unsigned int cfg = hpet_read(HPET_CFG);
+
+	cfg |= HPET_CFG_ENABLE;
+	hpet_write(HPET_CFG, cfg);
+}
+
+static void hpet_stop_counter(void)
+{
+	unsigned int cfg = hpet_read(HPET_CFG);
+
+	cfg &= ~HPET_CFG_ENABLE;
+	hpet_write(HPET_CFG, cfg);
+}
+
+static void hpet_reset_counter(void)
+{
+	hpet_write(HPET_COUNTER, 0);
+	hpet_write(HPET_COUNTER + 4, 0);
+}
+
+static void hpet_restart_counter(void)
+{
+	hpet_stop_counter();
+	hpet_reset_counter();
+	hpet_start_counter();
+}
+
+static void hpet_enable_legacy_int(void)
+{
+	/* Do nothing on Loongson-3 */
+}
+
+static int hpet_set_state_periodic(struct clock_event_device *evt)
+{
+	int cfg;
+
+	spin_lock(&hpet_lock);
+
+	pr_info("set clock event to periodic mode!\n");
+	/* stop counter */
+	hpet_stop_counter();
+
+	/* enables the timer0 to generate a periodic interrupt */
+	cfg = hpet_read(HPET_T0_CFG);
+	cfg &= ~HPET_TN_LEVEL;
+	cfg |= HPET_TN_ENABLE | HPET_TN_PERIODIC | HPET_TN_SETVAL |
+		HPET_TN_32BIT;
+	hpet_write(HPET_T0_CFG, cfg);
+
+	/* set the comparator */
+	hpet_write(HPET_T0_CMP, HPET_COMPARE_VAL);
+	udelay(1);
+	hpet_write(HPET_T0_CMP, HPET_COMPARE_VAL);
+
+	/* start counter */
+	hpet_start_counter();
+
+	spin_unlock(&hpet_lock);
+	return 0;
+}
+
+static int hpet_set_state_shutdown(struct clock_event_device *evt)
+{
+	int cfg;
+
+	spin_lock(&hpet_lock);
+
+	cfg = hpet_read(HPET_T0_CFG);
+	cfg &= ~HPET_TN_ENABLE;
+	hpet_write(HPET_T0_CFG, cfg);
+
+	spin_unlock(&hpet_lock);
+	return 0;
+}
+
+static int hpet_set_state_oneshot(struct clock_event_device *evt)
+{
+	int cfg;
+
+	spin_lock(&hpet_lock);
+
+	pr_info("set clock event to one shot mode!\n");
+	cfg = hpet_read(HPET_T0_CFG);
+	/*
+	 * set timer0 type
+	 * 1 : periodic interrupt
+	 * 0 : non-periodic(oneshot) interrupt
+	 */
+	cfg &= ~HPET_TN_PERIODIC;
+	cfg |= HPET_TN_ENABLE | HPET_TN_32BIT;
+	hpet_write(HPET_T0_CFG, cfg);
+
+	spin_unlock(&hpet_lock);
+	return 0;
+}
+
+static int hpet_tick_resume(struct clock_event_device *evt)
+{
+	spin_lock(&hpet_lock);
+	hpet_enable_legacy_int();
+	spin_unlock(&hpet_lock);
+
+	return 0;
+}
+
+static int hpet_next_event(unsigned long delta,
+		struct clock_event_device *evt)
+{
+	u32 cnt;
+	s32 res;
+
+	cnt = hpet_read(HPET_COUNTER);
+	cnt += (u32) delta;
+	hpet_write(HPET_T0_CMP, cnt);
+
+	res = (s32)(cnt - hpet_read(HPET_COUNTER));
+
+	return res < HPET_MIN_CYCLES ? -ETIME : 0;
+}
+
+static irqreturn_t hpet_irq_handler(int irq, void *data)
+{
+	int is_irq;
+	struct clock_event_device *cd;
+	unsigned int cpu = smp_processor_id();
+
+	is_irq = hpet_read(HPET_STATUS);
+	if (is_irq & HPET_T0_IRS) {
+		/* clear the TIMER0 irq status register */
+		hpet_write(HPET_STATUS, HPET_T0_IRS);
+		cd = &per_cpu(hpet_clockevent_device, cpu);
+		cd->event_handler(cd);
+		return IRQ_HANDLED;
+	}
+	return IRQ_NONE;
+}
+
+/*
+ * hpet address assignation and irq setting should be done in bios.
+ * but pmon don't do this, we just setup here directly.
+ * The operation under is normal. unfortunately, hpet_setup process
+ * is before pci initialize.
+ *
+ * {
+ *	struct pci_dev *pdev;
+ *
+ *	pdev = pci_get_device(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_SBX00_SMBUS, NULL);
+ *	pci_write_config_word(pdev, SMBUS_PCI_REGB4, HPET_ADDR);
+ *
+ *	...
+ * }
+ */
+static void hpet_setup(void)
+{
+	/* set hpet base address */
+	smbus_write(SMBUS_PCI_REGB4, HPET_ADDR);
+
+	/* enable decoding of access to HPET MMIO*/
+	smbus_enable(SMBUS_PCI_REG40, (1 << 28));
+
+	/* HPET irq enable */
+	smbus_enable(SMBUS_PCI_REG64, (1 << 10));
+
+	hpet_enable_legacy_int();
+}
+
+void __init setup_hpet_timer(void)
+{
+	unsigned long flags = IRQF_NOBALANCING | IRQF_TIMER;
+	unsigned int cpu = smp_processor_id();
+	struct clock_event_device *cd;
+
+	hpet_setup();
+
+	cd = &per_cpu(hpet_clockevent_device, cpu);
+	cd->name = "hpet";
+	cd->rating = 100;
+	cd->features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT;
+	cd->set_state_shutdown = hpet_set_state_shutdown;
+	cd->set_state_periodic = hpet_set_state_periodic;
+	cd->set_state_oneshot = hpet_set_state_oneshot;
+	cd->tick_resume = hpet_tick_resume;
+	cd->set_next_event = hpet_next_event;
+	cd->irq = HPET_T0_IRQ;
+	cd->cpumask = cpumask_of(cpu);
+	clockevent_set_clock(cd, HPET_FREQ);
+	cd->max_delta_ns = clockevent_delta2ns(0x7fffffff, cd);
+	cd->max_delta_ticks = 0x7fffffff;
+	cd->min_delta_ns = clockevent_delta2ns(HPET_MIN_PROG_DELTA, cd);
+	cd->min_delta_ticks = HPET_MIN_PROG_DELTA;
+
+	clockevents_register_device(cd);
+	if (request_irq(HPET_T0_IRQ, hpet_irq_handler, flags, "hpet", NULL))
+		pr_err("Failed to request irq %d (hpet)\n", HPET_T0_IRQ);
+	pr_info("hpet clock event device register\n");
+}
+
+static u64 hpet_read_counter(struct clocksource *cs)
+{
+	return (u64)hpet_read(HPET_COUNTER);
+}
+
+static void hpet_suspend(struct clocksource *cs)
+{
+}
+
+static void hpet_resume(struct clocksource *cs)
+{
+	hpet_setup();
+	hpet_restart_counter();
+}
+
+static struct clocksource csrc_hpet = {
+	.name = "hpet",
+	/* mips clocksource rating is less than 300, so hpet is better. */
+	.rating = 300,
+	.read = hpet_read_counter,
+	.mask = CLOCKSOURCE_MASK(32),
+	/* oneshot mode work normal with this flag */
+	.flags = CLOCK_SOURCE_IS_CONTINUOUS,
+	.suspend = hpet_suspend,
+	.resume = hpet_resume,
+	.mult = 0,
+	.shift = 10,
+};
+
+int __init init_hpet_clocksource(void)
+{
+	csrc_hpet.mult = clocksource_hz2mult(HPET_FREQ, csrc_hpet.shift);
+	return clocksource_register_hz(&csrc_hpet, HPET_FREQ);
+}
+
+arch_initcall(init_hpet_clocksource);
diff --git a/arch/mips/loongson64/init.c b/arch/mips/loongson64/init.c
new file mode 100644
index 000000000..f25caa6aa
--- /dev/null
+++ b/arch/mips/loongson64/init.c
@@ -0,0 +1,226 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2009 Lemote Inc.
+ * Author: Wu Zhangjin, wuzhangjin@gmail.com
+ */
+
+#include <linux/irqchip.h>
+#include <linux/logic_pio.h>
+#include <linux/memblock.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <asm/bootinfo.h>
+#include <asm/traps.h>
+#include <asm/smp-ops.h>
+#include <asm/cacheflush.h>
+#include <asm/fw/fw.h>
+
+#include <loongson.h>
+#include <boot_param.h>
+
+#define NODE_ID_OFFSET_ADDR	((void __iomem *)TO_UNCAC(0x1001041c))
+
+u32 node_id_offset;
+
+static void __init mips_nmi_setup(void)
+{
+	void *base;
+
+	base = (void *)(CAC_BASE + 0x380);
+	memcpy(base, except_vec_nmi, 0x80);
+	flush_icache_range((unsigned long)base, (unsigned long)base + 0x80);
+}
+
+void ls7a_early_config(void)
+{
+	node_id_offset = ((readl(NODE_ID_OFFSET_ADDR) >> 8) & 0x1f) + 36;
+}
+
+void rs780e_early_config(void)
+{
+	node_id_offset = 37;
+}
+
+void virtual_early_config(void)
+{
+	node_id_offset = 44;
+}
+
+void __init szmem(unsigned int node)
+{
+	u32 i, mem_type;
+	phys_addr_t node_id, mem_start, mem_size;
+
+	/* Otherwise come from DTB */
+	if (loongson_sysconf.fw_interface != LOONGSON_LEFI)
+		return;
+
+	/* Parse memory information and activate */
+	for (i = 0; i < loongson_memmap->nr_map; i++) {
+		node_id = loongson_memmap->map[i].node_id;
+		if (node_id != node)
+			continue;
+
+		mem_type = loongson_memmap->map[i].mem_type;
+		mem_size = loongson_memmap->map[i].mem_size;
+
+		/* Memory size comes in MB if MEM_SIZE_IS_IN_BYTES not set */
+		if (mem_size & MEM_SIZE_IS_IN_BYTES)
+			mem_size &= ~MEM_SIZE_IS_IN_BYTES;
+		else
+			mem_size = mem_size << 20;
+
+		mem_start = (node_id << 44) | loongson_memmap->map[i].mem_start;
+
+		switch (mem_type) {
+		case SYSTEM_RAM_LOW:
+		case SYSTEM_RAM_HIGH:
+		case UMA_VIDEO_RAM:
+			pr_info("Node %d, mem_type:%d\t[%pa], %pa bytes usable\n",
+				(u32)node_id, mem_type, &mem_start, &mem_size);
+			memblock_add_node(mem_start, mem_size, node,
+					  MEMBLOCK_NONE);
+			break;
+		case SYSTEM_RAM_RESERVED:
+		case VIDEO_ROM:
+		case ADAPTER_ROM:
+		case ACPI_TABLE:
+		case SMBIOS_TABLE:
+			pr_info("Node %d, mem_type:%d\t[%pa], %pa bytes reserved\n",
+				(u32)node_id, mem_type, &mem_start, &mem_size);
+			memblock_reserve(mem_start, mem_size);
+			break;
+		/* We should not reserve VUMA_VIDEO_RAM as it overlaps with MMIO */
+		case VUMA_VIDEO_RAM:
+		default:
+			pr_info("Node %d, mem_type:%d\t[%pa], %pa bytes unhandled\n",
+				(u32)node_id, mem_type, &mem_start, &mem_size);
+			break;
+		}
+	}
+
+	/* Reserve vgabios if it comes from firmware */
+	if (loongson_sysconf.vgabios_addr)
+		memblock_reserve(virt_to_phys((void *)loongson_sysconf.vgabios_addr),
+				SZ_256K);
+}
+
+#ifndef CONFIG_NUMA
+static void __init prom_init_memory(void)
+{
+	szmem(0);
+}
+#endif
+
+void __init prom_init(void)
+{
+	fw_init_cmdline();
+
+	if (fw_arg2 == 0 || (fdt_magic(fw_arg2) == FDT_MAGIC)) {
+		loongson_sysconf.fw_interface = LOONGSON_DTB;
+		prom_dtb_init_env();
+	} else {
+		loongson_sysconf.fw_interface = LOONGSON_LEFI;
+		prom_lefi_init_env();
+	}
+
+	/* init base address of io space */
+	set_io_port_base(PCI_IOBASE);
+
+	if (loongson_sysconf.early_config)
+		loongson_sysconf.early_config();
+
+#ifdef CONFIG_NUMA
+	prom_init_numa_memory();
+#else
+	prom_init_memory();
+#endif
+
+	/* Hardcode to CPU UART 0 */
+	if ((read_c0_prid() & PRID_IMP_MASK) == PRID_IMP_LOONGSON_64R)
+		setup_8250_early_printk_port(TO_UNCAC(LOONGSON_REG_BASE), 0, 1024);
+	else
+		setup_8250_early_printk_port(TO_UNCAC(LOONGSON_REG_BASE + 0x1e0), 0, 1024);
+
+	register_smp_ops(&loongson3_smp_ops);
+	board_nmi_handler_setup = mips_nmi_setup;
+}
+
+static int __init add_legacy_isa_io(struct fwnode_handle *fwnode, resource_size_t hw_start,
+				    resource_size_t size)
+{
+	int ret = 0;
+	struct logic_pio_hwaddr *range;
+	unsigned long vaddr;
+
+	range = kzalloc(sizeof(*range), GFP_ATOMIC);
+	if (!range)
+		return -ENOMEM;
+
+	range->fwnode = fwnode;
+	range->size = size = round_up(size, PAGE_SIZE);
+	range->hw_start = hw_start;
+	range->flags = LOGIC_PIO_CPU_MMIO;
+
+	ret = logic_pio_register_range(range);
+	if (ret) {
+		kfree(range);
+		return ret;
+	}
+
+	/* Legacy ISA must placed at the start of PCI_IOBASE */
+	if (range->io_start != 0) {
+		logic_pio_unregister_range(range);
+		kfree(range);
+		return -EINVAL;
+	}
+
+	vaddr = PCI_IOBASE + range->io_start;
+
+	ioremap_page_range(vaddr, vaddr + size, hw_start, pgprot_device(PAGE_KERNEL));
+
+	return 0;
+}
+
+static __init void reserve_pio_range(void)
+{
+	struct device_node *np;
+
+	for_each_node_by_name(np, "isa") {
+		struct of_range range;
+		struct of_range_parser parser;
+
+		pr_info("ISA Bridge: %pOF\n", np);
+
+		if (of_range_parser_init(&parser, np)) {
+			pr_info("Failed to parse resources.\n");
+			of_node_put(np);
+			break;
+		}
+
+		for_each_of_range(&parser, &range) {
+			switch (range.flags & IORESOURCE_TYPE_BITS) {
+			case IORESOURCE_IO:
+				pr_info(" IO 0x%016llx..0x%016llx  ->  0x%016llx\n",
+					range.cpu_addr,
+					range.cpu_addr + range.size - 1,
+					range.bus_addr);
+				if (add_legacy_isa_io(&np->fwnode, range.cpu_addr, range.size))
+					pr_warn("Failed to reserve legacy IO in Logic PIO\n");
+				break;
+			case IORESOURCE_MEM:
+				pr_info(" MEM 0x%016llx..0x%016llx  ->  0x%016llx\n",
+					range.cpu_addr,
+					range.cpu_addr + range.size - 1,
+					range.bus_addr);
+				break;
+			}
+		}
+	}
+}
+
+void __init arch_init_irq(void)
+{
+	reserve_pio_range();
+	irqchip_init();
+}
diff --git a/arch/mips/loongson64/numa.c b/arch/mips/loongson64/numa.c
new file mode 100644
index 000000000..8f61e93c0
--- /dev/null
+++ b/arch/mips/loongson64/numa.c
@@ -0,0 +1,208 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2010 Loongson Inc. & Lemote Inc. &
+ *                    Institute of Computing Technology
+ * Author:  Xiang Gao, gaoxiang@ict.ac.cn
+ *          Huacai Chen, chenhc@lemote.com
+ *          Xiaofu Meng, Shuangshuang Zhang
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/mm.h>
+#include <linux/mmzone.h>
+#include <linux/export.h>
+#include <linux/nodemask.h>
+#include <linux/swap.h>
+#include <linux/memblock.h>
+#include <linux/pfn.h>
+#include <linux/highmem.h>
+#include <asm/page.h>
+#include <asm/pgalloc.h>
+#include <asm/sections.h>
+#include <linux/irq.h>
+#include <asm/bootinfo.h>
+#include <asm/mc146818-time.h>
+#include <asm/time.h>
+#include <asm/wbflush.h>
+#include <boot_param.h>
+#include <loongson.h>
+
+unsigned char __node_distances[MAX_NUMNODES][MAX_NUMNODES];
+EXPORT_SYMBOL(__node_distances);
+struct pglist_data *__node_data[MAX_NUMNODES];
+EXPORT_SYMBOL(__node_data);
+
+cpumask_t __node_cpumask[MAX_NUMNODES];
+EXPORT_SYMBOL(__node_cpumask);
+
+static void cpu_node_probe(void)
+{
+	int i;
+
+	nodes_clear(node_possible_map);
+	nodes_clear(node_online_map);
+	for (i = 0; i < loongson_sysconf.nr_nodes; i++) {
+		node_set_state(num_online_nodes(), N_POSSIBLE);
+		node_set_online(num_online_nodes());
+	}
+
+	pr_info("NUMA: Discovered %d cpus on %d nodes\n",
+		loongson_sysconf.nr_cpus, num_online_nodes());
+}
+
+static int __init compute_node_distance(int row, int col)
+{
+	int package_row = row * loongson_sysconf.cores_per_node /
+				loongson_sysconf.cores_per_package;
+	int package_col = col * loongson_sysconf.cores_per_node /
+				loongson_sysconf.cores_per_package;
+
+	if (col == row)
+		return LOCAL_DISTANCE;
+	else if (package_row == package_col)
+		return 40;
+	else
+		return 100;
+}
+
+static void __init init_topology_matrix(void)
+{
+	int row, col;
+
+	for (row = 0; row < MAX_NUMNODES; row++)
+		for (col = 0; col < MAX_NUMNODES; col++)
+			__node_distances[row][col] = -1;
+
+	for_each_online_node(row) {
+		for_each_online_node(col) {
+			__node_distances[row][col] =
+				compute_node_distance(row, col);
+		}
+	}
+}
+
+static void __init node_mem_init(unsigned int node)
+{
+	struct pglist_data *nd;
+	unsigned long node_addrspace_offset;
+	unsigned long start_pfn, end_pfn;
+	unsigned long nd_pa;
+	int tnid;
+	const size_t nd_size = roundup(sizeof(pg_data_t), SMP_CACHE_BYTES);
+
+	node_addrspace_offset = nid_to_addrbase(node);
+	pr_info("Node%d's addrspace_offset is 0x%lx\n",
+			node, node_addrspace_offset);
+
+	get_pfn_range_for_nid(node, &start_pfn, &end_pfn);
+	pr_info("Node%d: start_pfn=0x%lx, end_pfn=0x%lx\n",
+		node, start_pfn, end_pfn);
+
+	nd_pa = memblock_phys_alloc_try_nid(nd_size, SMP_CACHE_BYTES, node);
+	if (!nd_pa)
+		panic("Cannot allocate %zu bytes for node %d data\n",
+		      nd_size, node);
+	nd = __va(nd_pa);
+	memset(nd, 0, sizeof(struct pglist_data));
+	tnid = early_pfn_to_nid(nd_pa >> PAGE_SHIFT);
+	if (tnid != node)
+		pr_info("NODE_DATA(%d) on node %d\n", node, tnid);
+	__node_data[node] = nd;
+	NODE_DATA(node)->node_start_pfn = start_pfn;
+	NODE_DATA(node)->node_spanned_pages = end_pfn - start_pfn;
+
+	if (node == 0) {
+		/* kernel start address */
+		unsigned long kernel_start_pfn = PFN_DOWN(__pa_symbol(&_text));
+
+		/* kernel end address */
+		unsigned long kernel_end_pfn = PFN_UP(__pa_symbol(&_end));
+
+		/* used by finalize_initrd() */
+		max_low_pfn = end_pfn;
+
+		/* Reserve the kernel text/data/bss */
+		memblock_reserve(kernel_start_pfn << PAGE_SHIFT,
+				 ((kernel_end_pfn - kernel_start_pfn) << PAGE_SHIFT));
+
+		/* Reserve 0xfe000000~0xffffffff for RS780E integrated GPU */
+		if (node_end_pfn(0) >= (0xffffffff >> PAGE_SHIFT))
+			memblock_reserve((node_addrspace_offset | 0xfe000000),
+					 32 << 20);
+
+		/* Reserve pfn range 0~node[0]->node_start_pfn */
+		memblock_reserve(0, PAGE_SIZE * start_pfn);
+	}
+}
+
+static __init void prom_meminit(void)
+{
+	unsigned int node, cpu, active_cpu = 0;
+
+	cpu_node_probe();
+	init_topology_matrix();
+
+	for (node = 0; node < loongson_sysconf.nr_nodes; node++) {
+		if (node_online(node)) {
+			szmem(node);
+			node_mem_init(node);
+			cpumask_clear(&__node_cpumask[node]);
+		}
+	}
+	max_low_pfn = PHYS_PFN(memblock_end_of_DRAM());
+
+	for (cpu = 0; cpu < loongson_sysconf.nr_cpus; cpu++) {
+		node = cpu / loongson_sysconf.cores_per_node;
+		if (node >= num_online_nodes())
+			node = 0;
+
+		if (loongson_sysconf.reserved_cpus_mask & (1<<cpu))
+			continue;
+
+		cpumask_set_cpu(active_cpu, &__node_cpumask[node]);
+		pr_info("NUMA: set cpumask cpu %d on node %d\n", active_cpu, node);
+
+		active_cpu++;
+	}
+}
+
+void __init paging_init(void)
+{
+	unsigned long zones_size[MAX_NR_ZONES] = {0, };
+
+	pagetable_init();
+	zones_size[ZONE_DMA32] = MAX_DMA32_PFN;
+	zones_size[ZONE_NORMAL] = max_low_pfn;
+	free_area_init(zones_size);
+}
+
+void __init mem_init(void)
+{
+	high_memory = (void *) __va(get_num_physpages() << PAGE_SHIFT);
+	memblock_free_all();
+	setup_zero_pages();	/* This comes from node 0 */
+}
+
+/* All PCI device belongs to logical Node-0 */
+int pcibus_to_node(struct pci_bus *bus)
+{
+	return 0;
+}
+EXPORT_SYMBOL(pcibus_to_node);
+
+void __init prom_init_numa_memory(void)
+{
+	pr_info("CP0_Config3: CP0 16.3 (0x%x)\n", read_c0_config3());
+	pr_info("CP0_PageGrain: CP0 5.1 (0x%x)\n", read_c0_pagegrain());
+	prom_meminit();
+}
+
+pg_data_t * __init arch_alloc_nodedata(int nid)
+{
+	return memblock_alloc(sizeof(pg_data_t), SMP_CACHE_BYTES);
+}
+
+void arch_refresh_nodedata(int nid, pg_data_t *pgdat)
+{
+	__node_data[nid] = pgdat;
+}
diff --git a/arch/mips/loongson64/pm.c b/arch/mips/loongson64/pm.c
new file mode 100644
index 000000000..7c8556f09
--- /dev/null
+++ b/arch/mips/loongson64/pm.c
@@ -0,0 +1,104 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * loongson-specific suspend support
+ *
+ *  Copyright (C) 2009 Lemote Inc.
+ *  Author: Wu Zhangjin <wuzhangjin@gmail.com>
+ */
+#include <linux/suspend.h>
+#include <linux/interrupt.h>
+#include <linux/pm.h>
+
+#include <asm/i8259.h>
+#include <asm/mipsregs.h>
+
+#include <loongson.h>
+
+static unsigned int __maybe_unused cached_master_mask;	/* i8259A */
+static unsigned int __maybe_unused cached_slave_mask;
+static unsigned int __maybe_unused cached_bonito_irq_mask; /* bonito */
+
+void arch_suspend_disable_irqs(void)
+{
+	/* disable all mips events */
+	local_irq_disable();
+
+#ifdef CONFIG_I8259
+	/* disable all events of i8259A */
+	cached_slave_mask = inb(PIC_SLAVE_IMR);
+	cached_master_mask = inb(PIC_MASTER_IMR);
+
+	outb(0xff, PIC_SLAVE_IMR);
+	inb(PIC_SLAVE_IMR);
+	outb(0xff, PIC_MASTER_IMR);
+	inb(PIC_MASTER_IMR);
+#endif
+	/* disable all events of bonito */
+	cached_bonito_irq_mask = LOONGSON_INTEN;
+	LOONGSON_INTENCLR = 0xffff;
+	(void)LOONGSON_INTENCLR;
+}
+
+void arch_suspend_enable_irqs(void)
+{
+	/* enable all mips events */
+	local_irq_enable();
+#ifdef CONFIG_I8259
+	/* only enable the cached events of i8259A */
+	outb(cached_slave_mask, PIC_SLAVE_IMR);
+	outb(cached_master_mask, PIC_MASTER_IMR);
+#endif
+	/* enable all cached events of bonito */
+	LOONGSON_INTENSET = cached_bonito_irq_mask;
+	(void)LOONGSON_INTENSET;
+}
+
+/*
+ * Setup the board-specific events for waking up loongson from wait mode
+ */
+void __weak setup_wakeup_events(void)
+{
+}
+
+void __weak mach_suspend(void)
+{
+}
+
+void __weak mach_resume(void)
+{
+}
+
+static int loongson_pm_enter(suspend_state_t state)
+{
+	mach_suspend();
+
+	mach_resume();
+
+	return 0;
+}
+
+static int loongson_pm_valid_state(suspend_state_t state)
+{
+	switch (state) {
+	case PM_SUSPEND_ON:
+	case PM_SUSPEND_STANDBY:
+	case PM_SUSPEND_MEM:
+		return 1;
+
+	default:
+		return 0;
+	}
+}
+
+static const struct platform_suspend_ops loongson_pm_ops = {
+	.valid	= loongson_pm_valid_state,
+	.enter	= loongson_pm_enter,
+};
+
+static int __init loongson_pm_init(void)
+{
+	suspend_set_ops(&loongson_pm_ops);
+
+	return 0;
+}
+arch_initcall(loongson_pm_init);
diff --git a/arch/mips/loongson64/reset.c b/arch/mips/loongson64/reset.c
new file mode 100644
index 000000000..e42080004
--- /dev/null
+++ b/arch/mips/loongson64/reset.c
@@ -0,0 +1,185 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *
+ * Copyright (C) 2007 Lemote, Inc. & Institute of Computing Technology
+ * Author: Fuxin Zhang, zhangfx@lemote.com
+ * Copyright (C) 2009 Lemote, Inc.
+ * Author: Zhangjin Wu, wuzhangjin@gmail.com
+ */
+#include <linux/cpu.h>
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/kexec.h>
+#include <linux/pm.h>
+#include <linux/slab.h>
+
+#include <asm/bootinfo.h>
+#include <asm/idle.h>
+#include <asm/reboot.h>
+#include <asm/bug.h>
+
+#include <loongson.h>
+#include <boot_param.h>
+
+static void loongson_restart(char *command)
+{
+
+	void (*fw_restart)(void) = (void *)loongson_sysconf.restart_addr;
+
+	fw_restart();
+	while (1) {
+		if (cpu_wait)
+			cpu_wait();
+	}
+}
+
+static void loongson_poweroff(void)
+{
+	void (*fw_poweroff)(void) = (void *)loongson_sysconf.poweroff_addr;
+
+	fw_poweroff();
+	while (1) {
+		if (cpu_wait)
+			cpu_wait();
+	}
+}
+
+static void loongson_halt(void)
+{
+	pr_notice("\n\n** You can safely turn off the power now **\n\n");
+	while (1) {
+		if (cpu_wait)
+			cpu_wait();
+	}
+}
+
+#ifdef CONFIG_KEXEC
+
+/* 0X80000000~0X80200000 is safe */
+#define MAX_ARGS	64
+#define KEXEC_CTRL_CODE	0xFFFFFFFF80100000UL
+#define KEXEC_ARGV_ADDR	0xFFFFFFFF80108000UL
+#define KEXEC_ARGV_SIZE	COMMAND_LINE_SIZE
+#define KEXEC_ENVP_SIZE	4800
+
+static int kexec_argc;
+static int kdump_argc;
+static void *kexec_argv;
+static void *kdump_argv;
+static void *kexec_envp;
+
+static int loongson_kexec_prepare(struct kimage *image)
+{
+	int i, argc = 0;
+	unsigned int *argv;
+	char *str, *ptr, *bootloader = "kexec";
+
+	/* argv at offset 0, argv[] at offset KEXEC_ARGV_SIZE/2 */
+	if (image->type == KEXEC_TYPE_DEFAULT)
+		argv = (unsigned int *)kexec_argv;
+	else
+		argv = (unsigned int *)kdump_argv;
+
+	argv[argc++] = (unsigned int)(KEXEC_ARGV_ADDR + KEXEC_ARGV_SIZE/2);
+
+	for (i = 0; i < image->nr_segments; i++) {
+		if (!strncmp(bootloader, (char *)image->segment[i].buf,
+				strlen(bootloader))) {
+			/*
+			 * convert command line string to array
+			 * of parameters (as bootloader does).
+			 */
+			int offt;
+			str = (char *)argv + KEXEC_ARGV_SIZE/2;
+			memcpy(str, image->segment[i].buf, KEXEC_ARGV_SIZE/2);
+			ptr = strchr(str, ' ');
+
+			while (ptr && (argc < MAX_ARGS)) {
+				*ptr = '\0';
+				if (ptr[1] != ' ') {
+					offt = (int)(ptr - str + 1);
+					argv[argc] = KEXEC_ARGV_ADDR + KEXEC_ARGV_SIZE/2 + offt;
+					argc++;
+				}
+				ptr = strchr(ptr + 1, ' ');
+			}
+			break;
+		}
+	}
+
+	if (image->type == KEXEC_TYPE_DEFAULT)
+		kexec_argc = argc;
+	else
+		kdump_argc = argc;
+
+	/* kexec/kdump need a safe page to save reboot_code_buffer */
+	image->control_code_page = virt_to_page((void *)KEXEC_CTRL_CODE);
+
+	return 0;
+}
+
+static void loongson_kexec_shutdown(void)
+{
+#ifdef CONFIG_SMP
+	int cpu;
+
+	/* All CPUs go to reboot_code_buffer */
+	for_each_possible_cpu(cpu)
+		if (!cpu_online(cpu))
+			cpu_device_up(get_cpu_device(cpu));
+
+	secondary_kexec_args[0] = TO_UNCAC(0x3ff01000);
+#endif
+	kexec_args[0] = kexec_argc;
+	kexec_args[1] = fw_arg1;
+	kexec_args[2] = fw_arg2;
+	memcpy((void *)fw_arg1, kexec_argv, KEXEC_ARGV_SIZE);
+	memcpy((void *)fw_arg2, kexec_envp, KEXEC_ENVP_SIZE);
+}
+
+static void loongson_crash_shutdown(struct pt_regs *regs)
+{
+	default_machine_crash_shutdown(regs);
+	kexec_args[0] = kdump_argc;
+	kexec_args[1] = fw_arg1;
+	kexec_args[2] = fw_arg2;
+#ifdef CONFIG_SMP
+	secondary_kexec_args[0] = TO_UNCAC(0x3ff01000);
+#endif
+	memcpy((void *)fw_arg1, kdump_argv, KEXEC_ARGV_SIZE);
+	memcpy((void *)fw_arg2, kexec_envp, KEXEC_ENVP_SIZE);
+}
+
+#endif
+
+static int __init mips_reboot_setup(void)
+{
+	_machine_restart = loongson_restart;
+	_machine_halt = loongson_halt;
+	pm_power_off = loongson_poweroff;
+
+#ifdef CONFIG_KEXEC
+	kexec_argv = kmalloc(KEXEC_ARGV_SIZE, GFP_KERNEL);
+	if (WARN_ON(!kexec_argv))
+		return -ENOMEM;
+
+	kdump_argv = kmalloc(KEXEC_ARGV_SIZE, GFP_KERNEL);
+	if (WARN_ON(!kdump_argv))
+		return -ENOMEM;
+
+	kexec_envp = kmalloc(KEXEC_ENVP_SIZE, GFP_KERNEL);
+	if (WARN_ON(!kexec_envp))
+		return -ENOMEM;
+
+	fw_arg1 = KEXEC_ARGV_ADDR;
+	memcpy(kexec_envp, (void *)fw_arg2, KEXEC_ENVP_SIZE);
+
+	_machine_kexec_prepare = loongson_kexec_prepare;
+	_machine_kexec_shutdown = loongson_kexec_shutdown;
+	_machine_crash_shutdown = loongson_crash_shutdown;
+#endif
+
+	return 0;
+}
+
+arch_initcall(mips_reboot_setup);
diff --git a/arch/mips/loongson64/setup.c b/arch/mips/loongson64/setup.c
new file mode 100644
index 000000000..3cd11c2b3
--- /dev/null
+++ b/arch/mips/loongson64/setup.c
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2007 Lemote Inc. & Institute of Computing Technology
+ * Author: Fuxin Zhang, zhangfx@lemote.com
+ */
+#include <linux/export.h>
+#include <linux/init.h>
+
+#include <asm/wbflush.h>
+#include <asm/bootinfo.h>
+#include <linux/libfdt.h>
+#include <linux/of_fdt.h>
+
+#include <asm/prom.h>
+
+#include <loongson.h>
+
+void *loongson_fdt_blob;
+
+static void wbflush_loongson(void)
+{
+	asm(".set\tpush\n\t"
+	    ".set\tnoreorder\n\t"
+	    ".set mips3\n\t"
+	    "sync\n\t"
+	    "nop\n\t"
+	    ".set\tpop\n\t"
+	    ".set mips0\n\t");
+}
+
+void (*__wbflush)(void) = wbflush_loongson;
+EXPORT_SYMBOL(__wbflush);
+
+void __init plat_mem_setup(void)
+{
+	if (loongson_fdt_blob)
+		__dt_setup_arch(loongson_fdt_blob);
+}
diff --git a/arch/mips/loongson64/smp.c b/arch/mips/loongson64/smp.c
new file mode 100644
index 000000000..660e1de44
--- /dev/null
+++ b/arch/mips/loongson64/smp.c
@@ -0,0 +1,881 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2010, 2011, 2012, Lemote, Inc.
+ * Author: Chen Huacai, chenhc@lemote.com
+ */
+
+#include <irq.h>
+#include <linux/init.h>
+#include <linux/cpu.h>
+#include <linux/sched.h>
+#include <linux/sched/hotplug.h>
+#include <linux/sched/task_stack.h>
+#include <linux/smp.h>
+#include <linux/cpufreq.h>
+#include <linux/kexec.h>
+#include <asm/processor.h>
+#include <asm/time.h>
+#include <asm/tlbflush.h>
+#include <asm/cacheflush.h>
+#include <loongson.h>
+#include <loongson_regs.h>
+#include <workarounds.h>
+
+#include "smp.h"
+
+DEFINE_PER_CPU(int, cpu_state);
+
+#define LS_IPI_IRQ (MIPS_CPU_IRQ_BASE + 6)
+
+static void *ipi_set0_regs[16];
+static void *ipi_clear0_regs[16];
+static void *ipi_status0_regs[16];
+static void *ipi_en0_regs[16];
+static void *ipi_mailbox_buf[16];
+static uint32_t core0_c0count[NR_CPUS];
+
+/* read a 32bit value from ipi register */
+#define loongson3_ipi_read32(addr) readl(addr)
+/* read a 64bit value from ipi register */
+#define loongson3_ipi_read64(addr) readq(addr)
+/* write a 32bit value to ipi register */
+#define loongson3_ipi_write32(action, addr)	\
+	do {					\
+		writel(action, addr);		\
+		__wbflush();			\
+	} while (0)
+/* write a 64bit value to ipi register */
+#define loongson3_ipi_write64(action, addr)	\
+	do {					\
+		writeq(action, addr);		\
+		__wbflush();			\
+	} while (0)
+
+static u32 (*ipi_read_clear)(int cpu);
+static void (*ipi_write_action)(int cpu, u32 action);
+static void (*ipi_write_enable)(int cpu);
+static void (*ipi_clear_buf)(int cpu);
+static void (*ipi_write_buf)(int cpu, struct task_struct *idle);
+
+/* send mail via Mail_Send register for 3A4000+ CPU */
+static void csr_mail_send(uint64_t data, int cpu, int mailbox)
+{
+	uint64_t val;
+
+	/* send high 32 bits */
+	val = CSR_MAIL_SEND_BLOCK;
+	val |= (CSR_MAIL_SEND_BOX_HIGH(mailbox) << CSR_MAIL_SEND_BOX_SHIFT);
+	val |= (cpu << CSR_MAIL_SEND_CPU_SHIFT);
+	val |= (data & CSR_MAIL_SEND_H32_MASK);
+	csr_writeq(val, LOONGSON_CSR_MAIL_SEND);
+
+	/* send low 32 bits */
+	val = CSR_MAIL_SEND_BLOCK;
+	val |= (CSR_MAIL_SEND_BOX_LOW(mailbox) << CSR_MAIL_SEND_BOX_SHIFT);
+	val |= (cpu << CSR_MAIL_SEND_CPU_SHIFT);
+	val |= (data << CSR_MAIL_SEND_BUF_SHIFT);
+	csr_writeq(val, LOONGSON_CSR_MAIL_SEND);
+};
+
+static u32 csr_ipi_read_clear(int cpu)
+{
+	u32 action;
+
+	/* Load the ipi register to figure out what we're supposed to do */
+	action = csr_readl(LOONGSON_CSR_IPI_STATUS);
+	/* Clear the ipi register to clear the interrupt */
+	csr_writel(action, LOONGSON_CSR_IPI_CLEAR);
+
+	return action;
+}
+
+static void csr_ipi_write_action(int cpu, u32 action)
+{
+	unsigned int irq = 0;
+
+	while ((irq = ffs(action))) {
+		uint32_t val = CSR_IPI_SEND_BLOCK;
+		val |= (irq - 1);
+		val |= (cpu << CSR_IPI_SEND_CPU_SHIFT);
+		csr_writel(val, LOONGSON_CSR_IPI_SEND);
+		action &= ~BIT(irq - 1);
+	}
+}
+
+static void csr_ipi_write_enable(int cpu)
+{
+	csr_writel(0xffffffff, LOONGSON_CSR_IPI_EN);
+}
+
+static void csr_ipi_clear_buf(int cpu)
+{
+	csr_writeq(0, LOONGSON_CSR_MAIL_BUF0);
+}
+
+static void csr_ipi_write_buf(int cpu, struct task_struct *idle)
+{
+	unsigned long startargs[4];
+
+	/* startargs[] are initial PC, SP and GP for secondary CPU */
+	startargs[0] = (unsigned long)&smp_bootstrap;
+	startargs[1] = (unsigned long)__KSTK_TOS(idle);
+	startargs[2] = (unsigned long)task_thread_info(idle);
+	startargs[3] = 0;
+
+	pr_debug("CPU#%d, func_pc=%lx, sp=%lx, gp=%lx\n",
+		cpu, startargs[0], startargs[1], startargs[2]);
+
+	csr_mail_send(startargs[3], cpu_logical_map(cpu), 3);
+	csr_mail_send(startargs[2], cpu_logical_map(cpu), 2);
+	csr_mail_send(startargs[1], cpu_logical_map(cpu), 1);
+	csr_mail_send(startargs[0], cpu_logical_map(cpu), 0);
+}
+
+static u32 legacy_ipi_read_clear(int cpu)
+{
+	u32 action;
+
+	/* Load the ipi register to figure out what we're supposed to do */
+	action = loongson3_ipi_read32(ipi_status0_regs[cpu_logical_map(cpu)]);
+	/* Clear the ipi register to clear the interrupt */
+	loongson3_ipi_write32(action, ipi_clear0_regs[cpu_logical_map(cpu)]);
+
+	return action;
+}
+
+static void legacy_ipi_write_action(int cpu, u32 action)
+{
+	loongson3_ipi_write32((u32)action, ipi_set0_regs[cpu]);
+}
+
+static void legacy_ipi_write_enable(int cpu)
+{
+	loongson3_ipi_write32(0xffffffff, ipi_en0_regs[cpu_logical_map(cpu)]);
+}
+
+static void legacy_ipi_clear_buf(int cpu)
+{
+	loongson3_ipi_write64(0, ipi_mailbox_buf[cpu_logical_map(cpu)] + 0x0);
+}
+
+static void legacy_ipi_write_buf(int cpu, struct task_struct *idle)
+{
+	unsigned long startargs[4];
+
+	/* startargs[] are initial PC, SP and GP for secondary CPU */
+	startargs[0] = (unsigned long)&smp_bootstrap;
+	startargs[1] = (unsigned long)__KSTK_TOS(idle);
+	startargs[2] = (unsigned long)task_thread_info(idle);
+	startargs[3] = 0;
+
+	pr_debug("CPU#%d, func_pc=%lx, sp=%lx, gp=%lx\n",
+			cpu, startargs[0], startargs[1], startargs[2]);
+
+	loongson3_ipi_write64(startargs[3],
+			ipi_mailbox_buf[cpu_logical_map(cpu)] + 0x18);
+	loongson3_ipi_write64(startargs[2],
+			ipi_mailbox_buf[cpu_logical_map(cpu)] + 0x10);
+	loongson3_ipi_write64(startargs[1],
+			ipi_mailbox_buf[cpu_logical_map(cpu)] + 0x8);
+	loongson3_ipi_write64(startargs[0],
+			ipi_mailbox_buf[cpu_logical_map(cpu)] + 0x0);
+}
+
+static void csr_ipi_probe(void)
+{
+	if (cpu_has_csr() && csr_readl(LOONGSON_CSR_FEATURES) & LOONGSON_CSRF_IPI) {
+		ipi_read_clear = csr_ipi_read_clear;
+		ipi_write_action = csr_ipi_write_action;
+		ipi_write_enable = csr_ipi_write_enable;
+		ipi_clear_buf = csr_ipi_clear_buf;
+		ipi_write_buf = csr_ipi_write_buf;
+	} else {
+		ipi_read_clear = legacy_ipi_read_clear;
+		ipi_write_action = legacy_ipi_write_action;
+		ipi_write_enable = legacy_ipi_write_enable;
+		ipi_clear_buf = legacy_ipi_clear_buf;
+		ipi_write_buf = legacy_ipi_write_buf;
+	}
+}
+
+static void ipi_set0_regs_init(void)
+{
+	ipi_set0_regs[0] = (void *)
+		(SMP_CORE_GROUP0_BASE + SMP_CORE0_OFFSET + SET0);
+	ipi_set0_regs[1] = (void *)
+		(SMP_CORE_GROUP0_BASE + SMP_CORE1_OFFSET + SET0);
+	ipi_set0_regs[2] = (void *)
+		(SMP_CORE_GROUP0_BASE + SMP_CORE2_OFFSET + SET0);
+	ipi_set0_regs[3] = (void *)
+		(SMP_CORE_GROUP0_BASE + SMP_CORE3_OFFSET + SET0);
+	ipi_set0_regs[4] = (void *)
+		(SMP_CORE_GROUP1_BASE + SMP_CORE0_OFFSET + SET0);
+	ipi_set0_regs[5] = (void *)
+		(SMP_CORE_GROUP1_BASE + SMP_CORE1_OFFSET + SET0);
+	ipi_set0_regs[6] = (void *)
+		(SMP_CORE_GROUP1_BASE + SMP_CORE2_OFFSET + SET0);
+	ipi_set0_regs[7] = (void *)
+		(SMP_CORE_GROUP1_BASE + SMP_CORE3_OFFSET + SET0);
+	ipi_set0_regs[8] = (void *)
+		(SMP_CORE_GROUP2_BASE + SMP_CORE0_OFFSET + SET0);
+	ipi_set0_regs[9] = (void *)
+		(SMP_CORE_GROUP2_BASE + SMP_CORE1_OFFSET + SET0);
+	ipi_set0_regs[10] = (void *)
+		(SMP_CORE_GROUP2_BASE + SMP_CORE2_OFFSET + SET0);
+	ipi_set0_regs[11] = (void *)
+		(SMP_CORE_GROUP2_BASE + SMP_CORE3_OFFSET + SET0);
+	ipi_set0_regs[12] = (void *)
+		(SMP_CORE_GROUP3_BASE + SMP_CORE0_OFFSET + SET0);
+	ipi_set0_regs[13] = (void *)
+		(SMP_CORE_GROUP3_BASE + SMP_CORE1_OFFSET + SET0);
+	ipi_set0_regs[14] = (void *)
+		(SMP_CORE_GROUP3_BASE + SMP_CORE2_OFFSET + SET0);
+	ipi_set0_regs[15] = (void *)
+		(SMP_CORE_GROUP3_BASE + SMP_CORE3_OFFSET + SET0);
+}
+
+static void ipi_clear0_regs_init(void)
+{
+	ipi_clear0_regs[0] = (void *)
+		(SMP_CORE_GROUP0_BASE + SMP_CORE0_OFFSET + CLEAR0);
+	ipi_clear0_regs[1] = (void *)
+		(SMP_CORE_GROUP0_BASE + SMP_CORE1_OFFSET + CLEAR0);
+	ipi_clear0_regs[2] = (void *)
+		(SMP_CORE_GROUP0_BASE + SMP_CORE2_OFFSET + CLEAR0);
+	ipi_clear0_regs[3] = (void *)
+		(SMP_CORE_GROUP0_BASE + SMP_CORE3_OFFSET + CLEAR0);
+	ipi_clear0_regs[4] = (void *)
+		(SMP_CORE_GROUP1_BASE + SMP_CORE0_OFFSET + CLEAR0);
+	ipi_clear0_regs[5] = (void *)
+		(SMP_CORE_GROUP1_BASE + SMP_CORE1_OFFSET + CLEAR0);
+	ipi_clear0_regs[6] = (void *)
+		(SMP_CORE_GROUP1_BASE + SMP_CORE2_OFFSET + CLEAR0);
+	ipi_clear0_regs[7] = (void *)
+		(SMP_CORE_GROUP1_BASE + SMP_CORE3_OFFSET + CLEAR0);
+	ipi_clear0_regs[8] = (void *)
+		(SMP_CORE_GROUP2_BASE + SMP_CORE0_OFFSET + CLEAR0);
+	ipi_clear0_regs[9] = (void *)
+		(SMP_CORE_GROUP2_BASE + SMP_CORE1_OFFSET + CLEAR0);
+	ipi_clear0_regs[10] = (void *)
+		(SMP_CORE_GROUP2_BASE + SMP_CORE2_OFFSET + CLEAR0);
+	ipi_clear0_regs[11] = (void *)
+		(SMP_CORE_GROUP2_BASE + SMP_CORE3_OFFSET + CLEAR0);
+	ipi_clear0_regs[12] = (void *)
+		(SMP_CORE_GROUP3_BASE + SMP_CORE0_OFFSET + CLEAR0);
+	ipi_clear0_regs[13] = (void *)
+		(SMP_CORE_GROUP3_BASE + SMP_CORE1_OFFSET + CLEAR0);
+	ipi_clear0_regs[14] = (void *)
+		(SMP_CORE_GROUP3_BASE + SMP_CORE2_OFFSET + CLEAR0);
+	ipi_clear0_regs[15] = (void *)
+		(SMP_CORE_GROUP3_BASE + SMP_CORE3_OFFSET + CLEAR0);
+}
+
+static void ipi_status0_regs_init(void)
+{
+	ipi_status0_regs[0] = (void *)
+		(SMP_CORE_GROUP0_BASE + SMP_CORE0_OFFSET + STATUS0);
+	ipi_status0_regs[1] = (void *)
+		(SMP_CORE_GROUP0_BASE + SMP_CORE1_OFFSET + STATUS0);
+	ipi_status0_regs[2] = (void *)
+		(SMP_CORE_GROUP0_BASE + SMP_CORE2_OFFSET + STATUS0);
+	ipi_status0_regs[3] = (void *)
+		(SMP_CORE_GROUP0_BASE + SMP_CORE3_OFFSET + STATUS0);
+	ipi_status0_regs[4] = (void *)
+		(SMP_CORE_GROUP1_BASE + SMP_CORE0_OFFSET + STATUS0);
+	ipi_status0_regs[5] = (void *)
+		(SMP_CORE_GROUP1_BASE + SMP_CORE1_OFFSET + STATUS0);
+	ipi_status0_regs[6] = (void *)
+		(SMP_CORE_GROUP1_BASE + SMP_CORE2_OFFSET + STATUS0);
+	ipi_status0_regs[7] = (void *)
+		(SMP_CORE_GROUP1_BASE + SMP_CORE3_OFFSET + STATUS0);
+	ipi_status0_regs[8] = (void *)
+		(SMP_CORE_GROUP2_BASE + SMP_CORE0_OFFSET + STATUS0);
+	ipi_status0_regs[9] = (void *)
+		(SMP_CORE_GROUP2_BASE + SMP_CORE1_OFFSET + STATUS0);
+	ipi_status0_regs[10] = (void *)
+		(SMP_CORE_GROUP2_BASE + SMP_CORE2_OFFSET + STATUS0);
+	ipi_status0_regs[11] = (void *)
+		(SMP_CORE_GROUP2_BASE + SMP_CORE3_OFFSET + STATUS0);
+	ipi_status0_regs[12] = (void *)
+		(SMP_CORE_GROUP3_BASE + SMP_CORE0_OFFSET + STATUS0);
+	ipi_status0_regs[13] = (void *)
+		(SMP_CORE_GROUP3_BASE + SMP_CORE1_OFFSET + STATUS0);
+	ipi_status0_regs[14] = (void *)
+		(SMP_CORE_GROUP3_BASE + SMP_CORE2_OFFSET + STATUS0);
+	ipi_status0_regs[15] = (void *)
+		(SMP_CORE_GROUP3_BASE + SMP_CORE3_OFFSET + STATUS0);
+}
+
+static void ipi_en0_regs_init(void)
+{
+	ipi_en0_regs[0] = (void *)
+		(SMP_CORE_GROUP0_BASE + SMP_CORE0_OFFSET + EN0);
+	ipi_en0_regs[1] = (void *)
+		(SMP_CORE_GROUP0_BASE + SMP_CORE1_OFFSET + EN0);
+	ipi_en0_regs[2] = (void *)
+		(SMP_CORE_GROUP0_BASE + SMP_CORE2_OFFSET + EN0);
+	ipi_en0_regs[3] = (void *)
+		(SMP_CORE_GROUP0_BASE + SMP_CORE3_OFFSET + EN0);
+	ipi_en0_regs[4] = (void *)
+		(SMP_CORE_GROUP1_BASE + SMP_CORE0_OFFSET + EN0);
+	ipi_en0_regs[5] = (void *)
+		(SMP_CORE_GROUP1_BASE + SMP_CORE1_OFFSET + EN0);
+	ipi_en0_regs[6] = (void *)
+		(SMP_CORE_GROUP1_BASE + SMP_CORE2_OFFSET + EN0);
+	ipi_en0_regs[7] = (void *)
+		(SMP_CORE_GROUP1_BASE + SMP_CORE3_OFFSET + EN0);
+	ipi_en0_regs[8] = (void *)
+		(SMP_CORE_GROUP2_BASE + SMP_CORE0_OFFSET + EN0);
+	ipi_en0_regs[9] = (void *)
+		(SMP_CORE_GROUP2_BASE + SMP_CORE1_OFFSET + EN0);
+	ipi_en0_regs[10] = (void *)
+		(SMP_CORE_GROUP2_BASE + SMP_CORE2_OFFSET + EN0);
+	ipi_en0_regs[11] = (void *)
+		(SMP_CORE_GROUP2_BASE + SMP_CORE3_OFFSET + EN0);
+	ipi_en0_regs[12] = (void *)
+		(SMP_CORE_GROUP3_BASE + SMP_CORE0_OFFSET + EN0);
+	ipi_en0_regs[13] = (void *)
+		(SMP_CORE_GROUP3_BASE + SMP_CORE1_OFFSET + EN0);
+	ipi_en0_regs[14] = (void *)
+		(SMP_CORE_GROUP3_BASE + SMP_CORE2_OFFSET + EN0);
+	ipi_en0_regs[15] = (void *)
+		(SMP_CORE_GROUP3_BASE + SMP_CORE3_OFFSET + EN0);
+}
+
+static void ipi_mailbox_buf_init(void)
+{
+	ipi_mailbox_buf[0] = (void *)
+		(SMP_CORE_GROUP0_BASE + SMP_CORE0_OFFSET + BUF);
+	ipi_mailbox_buf[1] = (void *)
+		(SMP_CORE_GROUP0_BASE + SMP_CORE1_OFFSET + BUF);
+	ipi_mailbox_buf[2] = (void *)
+		(SMP_CORE_GROUP0_BASE + SMP_CORE2_OFFSET + BUF);
+	ipi_mailbox_buf[3] = (void *)
+		(SMP_CORE_GROUP0_BASE + SMP_CORE3_OFFSET + BUF);
+	ipi_mailbox_buf[4] = (void *)
+		(SMP_CORE_GROUP1_BASE + SMP_CORE0_OFFSET + BUF);
+	ipi_mailbox_buf[5] = (void *)
+		(SMP_CORE_GROUP1_BASE + SMP_CORE1_OFFSET + BUF);
+	ipi_mailbox_buf[6] = (void *)
+		(SMP_CORE_GROUP1_BASE + SMP_CORE2_OFFSET + BUF);
+	ipi_mailbox_buf[7] = (void *)
+		(SMP_CORE_GROUP1_BASE + SMP_CORE3_OFFSET + BUF);
+	ipi_mailbox_buf[8] = (void *)
+		(SMP_CORE_GROUP2_BASE + SMP_CORE0_OFFSET + BUF);
+	ipi_mailbox_buf[9] = (void *)
+		(SMP_CORE_GROUP2_BASE + SMP_CORE1_OFFSET + BUF);
+	ipi_mailbox_buf[10] = (void *)
+		(SMP_CORE_GROUP2_BASE + SMP_CORE2_OFFSET + BUF);
+	ipi_mailbox_buf[11] = (void *)
+		(SMP_CORE_GROUP2_BASE + SMP_CORE3_OFFSET + BUF);
+	ipi_mailbox_buf[12] = (void *)
+		(SMP_CORE_GROUP3_BASE + SMP_CORE0_OFFSET + BUF);
+	ipi_mailbox_buf[13] = (void *)
+		(SMP_CORE_GROUP3_BASE + SMP_CORE1_OFFSET + BUF);
+	ipi_mailbox_buf[14] = (void *)
+		(SMP_CORE_GROUP3_BASE + SMP_CORE2_OFFSET + BUF);
+	ipi_mailbox_buf[15] = (void *)
+		(SMP_CORE_GROUP3_BASE + SMP_CORE3_OFFSET + BUF);
+}
+
+/*
+ * Simple enough, just poke the appropriate ipi register
+ */
+static void loongson3_send_ipi_single(int cpu, unsigned int action)
+{
+	ipi_write_action(cpu_logical_map(cpu), (u32)action);
+}
+
+static void
+loongson3_send_ipi_mask(const struct cpumask *mask, unsigned int action)
+{
+	unsigned int i;
+
+	for_each_cpu(i, mask)
+		ipi_write_action(cpu_logical_map(i), (u32)action);
+}
+
+
+static irqreturn_t loongson3_ipi_interrupt(int irq, void *dev_id)
+{
+	int i, cpu = smp_processor_id();
+	unsigned int action, c0count;
+
+	action = ipi_read_clear(cpu);
+
+	if (action & SMP_RESCHEDULE_YOURSELF)
+		scheduler_ipi();
+
+	if (action & SMP_CALL_FUNCTION) {
+		irq_enter();
+		generic_smp_call_function_interrupt();
+		irq_exit();
+	}
+
+	if (action & SMP_ASK_C0COUNT) {
+		BUG_ON(cpu != 0);
+		c0count = read_c0_count();
+		c0count = c0count ? c0count : 1;
+		for (i = 1; i < nr_cpu_ids; i++)
+			core0_c0count[i] = c0count;
+		__wbflush(); /* Let others see the result ASAP */
+	}
+
+	return IRQ_HANDLED;
+}
+
+#define MAX_LOOPS 800
+/*
+ * SMP init and finish on secondary CPUs
+ */
+static void loongson3_init_secondary(void)
+{
+	int i;
+	uint32_t initcount;
+	unsigned int cpu = smp_processor_id();
+	unsigned int imask = STATUSF_IP7 | STATUSF_IP6 |
+			     STATUSF_IP3 | STATUSF_IP2;
+
+	/* Set interrupt mask, but don't enable */
+	change_c0_status(ST0_IM, imask);
+	ipi_write_enable(cpu);
+
+	per_cpu(cpu_state, cpu) = CPU_ONLINE;
+	cpu_set_core(&cpu_data[cpu],
+		     cpu_logical_map(cpu) % loongson_sysconf.cores_per_package);
+	cpu_data[cpu].package =
+		cpu_logical_map(cpu) / loongson_sysconf.cores_per_package;
+
+	i = 0;
+	core0_c0count[cpu] = 0;
+	loongson3_send_ipi_single(0, SMP_ASK_C0COUNT);
+	while (!core0_c0count[cpu]) {
+		i++;
+		cpu_relax();
+	}
+
+	if (i > MAX_LOOPS)
+		i = MAX_LOOPS;
+	if (cpu_data[cpu].package)
+		initcount = core0_c0count[cpu] + i;
+	else /* Local access is faster for loops */
+		initcount = core0_c0count[cpu] + i/2;
+
+	write_c0_count(initcount);
+}
+
+static void loongson3_smp_finish(void)
+{
+	int cpu = smp_processor_id();
+
+	write_c0_compare(read_c0_count() + mips_hpt_frequency/HZ);
+	local_irq_enable();
+	ipi_clear_buf(cpu);
+
+	pr_info("CPU#%d finished, CP0_ST=%x\n",
+			smp_processor_id(), read_c0_status());
+}
+
+static void __init loongson3_smp_setup(void)
+{
+	int i = 0, num = 0; /* i: physical id, num: logical id */
+
+	init_cpu_possible(cpu_none_mask);
+
+	/* For unified kernel, NR_CPUS is the maximum possible value,
+	 * loongson_sysconf.nr_cpus is the really present value
+	 */
+	while (i < loongson_sysconf.nr_cpus) {
+		if (loongson_sysconf.reserved_cpus_mask & (1<<i)) {
+			/* Reserved physical CPU cores */
+			__cpu_number_map[i] = -1;
+		} else {
+			__cpu_number_map[i] = num;
+			__cpu_logical_map[num] = i;
+			set_cpu_possible(num, true);
+			/* Loongson processors are always grouped by 4 */
+			cpu_set_cluster(&cpu_data[num], i / 4);
+			num++;
+		}
+		i++;
+	}
+	pr_info("Detected %i available CPU(s)\n", num);
+
+	while (num < loongson_sysconf.nr_cpus) {
+		__cpu_logical_map[num] = -1;
+		num++;
+	}
+
+	csr_ipi_probe();
+	ipi_set0_regs_init();
+	ipi_clear0_regs_init();
+	ipi_status0_regs_init();
+	ipi_en0_regs_init();
+	ipi_mailbox_buf_init();
+	ipi_write_enable(0);
+
+	cpu_set_core(&cpu_data[0],
+		     cpu_logical_map(0) % loongson_sysconf.cores_per_package);
+	cpu_data[0].package = cpu_logical_map(0) / loongson_sysconf.cores_per_package;
+}
+
+static void __init loongson3_prepare_cpus(unsigned int max_cpus)
+{
+	if (request_irq(LS_IPI_IRQ, loongson3_ipi_interrupt,
+			IRQF_PERCPU | IRQF_NO_SUSPEND, "SMP_IPI", NULL))
+		pr_err("Failed to request IPI IRQ\n");
+	init_cpu_present(cpu_possible_mask);
+	per_cpu(cpu_state, smp_processor_id()) = CPU_ONLINE;
+}
+
+/*
+ * Setup the PC, SP, and GP of a secondary processor and start it runing!
+ */
+static int loongson3_boot_secondary(int cpu, struct task_struct *idle)
+{
+	pr_info("Booting CPU#%d...\n", cpu);
+
+	ipi_write_buf(cpu, idle);
+
+	return 0;
+}
+
+#ifdef CONFIG_HOTPLUG_CPU
+
+static int loongson3_cpu_disable(void)
+{
+	unsigned long flags;
+	unsigned int cpu = smp_processor_id();
+
+	set_cpu_online(cpu, false);
+	calculate_cpu_foreign_map();
+	local_irq_save(flags);
+	clear_c0_status(ST0_IM);
+	local_irq_restore(flags);
+	local_flush_tlb_all();
+
+	return 0;
+}
+
+
+static void loongson3_cpu_die(unsigned int cpu)
+{
+	while (per_cpu(cpu_state, cpu) != CPU_DEAD)
+		cpu_relax();
+
+	mb();
+}
+
+/* To shutdown a core in Loongson 3, the target core should go to CKSEG1 and
+ * flush all L1 entries at first. Then, another core (usually Core 0) can
+ * safely disable the clock of the target core. loongson3_play_dead() is
+ * called via CKSEG1 (uncached and unmmaped)
+ */
+static void loongson3_type1_play_dead(int *state_addr)
+{
+	register int val;
+	register long cpuid, core, node, count;
+	register void *addr, *base, *initfunc;
+
+	__asm__ __volatile__(
+		"   .set push                     \n"
+		"   .set noreorder                \n"
+		"   li %[addr], 0x80000000        \n" /* KSEG0 */
+		"1: cache 0, 0(%[addr])           \n" /* flush L1 ICache */
+		"   cache 0, 1(%[addr])           \n"
+		"   cache 0, 2(%[addr])           \n"
+		"   cache 0, 3(%[addr])           \n"
+		"   cache 1, 0(%[addr])           \n" /* flush L1 DCache */
+		"   cache 1, 1(%[addr])           \n"
+		"   cache 1, 2(%[addr])           \n"
+		"   cache 1, 3(%[addr])           \n"
+		"   addiu %[sets], %[sets], -1    \n"
+		"   bnez  %[sets], 1b             \n"
+		"   addiu %[addr], %[addr], 0x20  \n"
+		"   li    %[val], 0x7             \n" /* *state_addr = CPU_DEAD; */
+		"   sw    %[val], (%[state_addr]) \n"
+		"   sync                          \n"
+		"   cache 21, (%[state_addr])     \n" /* flush entry of *state_addr */
+		"   .set pop                      \n"
+		: [addr] "=&r" (addr), [val] "=&r" (val)
+		: [state_addr] "r" (state_addr),
+		  [sets] "r" (cpu_data[smp_processor_id()].dcache.sets));
+
+	__asm__ __volatile__(
+		"   .set push                         \n"
+		"   .set noreorder                    \n"
+		"   .set mips64                       \n"
+		"   mfc0  %[cpuid], $15, 1            \n"
+		"   andi  %[cpuid], 0x3ff             \n"
+		"   dli   %[base], 0x900000003ff01000 \n"
+		"   andi  %[core], %[cpuid], 0x3      \n"
+		"   sll   %[core], 8                  \n" /* get core id */
+		"   or    %[base], %[base], %[core]   \n"
+		"   andi  %[node], %[cpuid], 0xc      \n"
+		"   dsll  %[node], 42                 \n" /* get node id */
+		"   or    %[base], %[base], %[node]   \n"
+		"1: li    %[count], 0x100             \n" /* wait for init loop */
+		"2: bnez  %[count], 2b                \n" /* limit mailbox access */
+		"   addiu %[count], -1                \n"
+		"   ld    %[initfunc], 0x20(%[base])  \n" /* get PC via mailbox */
+		"   beqz  %[initfunc], 1b             \n"
+		"   nop                               \n"
+		"   ld    $sp, 0x28(%[base])          \n" /* get SP via mailbox */
+		"   ld    $gp, 0x30(%[base])          \n" /* get GP via mailbox */
+		"   ld    $a1, 0x38(%[base])          \n"
+		"   jr    %[initfunc]                 \n" /* jump to initial PC */
+		"   nop                               \n"
+		"   .set pop                          \n"
+		: [core] "=&r" (core), [node] "=&r" (node),
+		  [base] "=&r" (base), [cpuid] "=&r" (cpuid),
+		  [count] "=&r" (count), [initfunc] "=&r" (initfunc)
+		: /* No Input */
+		: "a1");
+}
+
+static void loongson3_type2_play_dead(int *state_addr)
+{
+	register int val;
+	register long cpuid, core, node, count;
+	register void *addr, *base, *initfunc;
+
+	__asm__ __volatile__(
+		"   .set push                     \n"
+		"   .set noreorder                \n"
+		"   li %[addr], 0x80000000        \n" /* KSEG0 */
+		"1: cache 0, 0(%[addr])           \n" /* flush L1 ICache */
+		"   cache 0, 1(%[addr])           \n"
+		"   cache 0, 2(%[addr])           \n"
+		"   cache 0, 3(%[addr])           \n"
+		"   cache 1, 0(%[addr])           \n" /* flush L1 DCache */
+		"   cache 1, 1(%[addr])           \n"
+		"   cache 1, 2(%[addr])           \n"
+		"   cache 1, 3(%[addr])           \n"
+		"   addiu %[sets], %[sets], -1    \n"
+		"   bnez  %[sets], 1b             \n"
+		"   addiu %[addr], %[addr], 0x20  \n"
+		"   li    %[val], 0x7             \n" /* *state_addr = CPU_DEAD; */
+		"   sw    %[val], (%[state_addr]) \n"
+		"   sync                          \n"
+		"   cache 21, (%[state_addr])     \n" /* flush entry of *state_addr */
+		"   .set pop                      \n"
+		: [addr] "=&r" (addr), [val] "=&r" (val)
+		: [state_addr] "r" (state_addr),
+		  [sets] "r" (cpu_data[smp_processor_id()].dcache.sets));
+
+	__asm__ __volatile__(
+		"   .set push                         \n"
+		"   .set noreorder                    \n"
+		"   .set mips64                       \n"
+		"   mfc0  %[cpuid], $15, 1            \n"
+		"   andi  %[cpuid], 0x3ff             \n"
+		"   dli   %[base], 0x900000003ff01000 \n"
+		"   andi  %[core], %[cpuid], 0x3      \n"
+		"   sll   %[core], 8                  \n" /* get core id */
+		"   or    %[base], %[base], %[core]   \n"
+		"   andi  %[node], %[cpuid], 0xc      \n"
+		"   dsll  %[node], 42                 \n" /* get node id */
+		"   or    %[base], %[base], %[node]   \n"
+		"   dsrl  %[node], 30                 \n" /* 15:14 */
+		"   or    %[base], %[base], %[node]   \n"
+		"1: li    %[count], 0x100             \n" /* wait for init loop */
+		"2: bnez  %[count], 2b                \n" /* limit mailbox access */
+		"   addiu %[count], -1                \n"
+		"   ld    %[initfunc], 0x20(%[base])  \n" /* get PC via mailbox */
+		"   beqz  %[initfunc], 1b             \n"
+		"   nop                               \n"
+		"   ld    $sp, 0x28(%[base])          \n" /* get SP via mailbox */
+		"   ld    $gp, 0x30(%[base])          \n" /* get GP via mailbox */
+		"   ld    $a1, 0x38(%[base])          \n"
+		"   jr    %[initfunc]                 \n" /* jump to initial PC */
+		"   nop                               \n"
+		"   .set pop                          \n"
+		: [core] "=&r" (core), [node] "=&r" (node),
+		  [base] "=&r" (base), [cpuid] "=&r" (cpuid),
+		  [count] "=&r" (count), [initfunc] "=&r" (initfunc)
+		: /* No Input */
+		: "a1");
+}
+
+static void loongson3_type3_play_dead(int *state_addr)
+{
+	register int val;
+	register long cpuid, core, node, count;
+	register void *addr, *base, *initfunc;
+
+	__asm__ __volatile__(
+		"   .set push                     \n"
+		"   .set noreorder                \n"
+		"   li %[addr], 0x80000000        \n" /* KSEG0 */
+		"1: cache 0, 0(%[addr])           \n" /* flush L1 ICache */
+		"   cache 0, 1(%[addr])           \n"
+		"   cache 0, 2(%[addr])           \n"
+		"   cache 0, 3(%[addr])           \n"
+		"   cache 1, 0(%[addr])           \n" /* flush L1 DCache */
+		"   cache 1, 1(%[addr])           \n"
+		"   cache 1, 2(%[addr])           \n"
+		"   cache 1, 3(%[addr])           \n"
+		"   addiu %[sets], %[sets], -1    \n"
+		"   bnez  %[sets], 1b             \n"
+		"   addiu %[addr], %[addr], 0x40  \n"
+		"   li %[addr], 0x80000000        \n" /* KSEG0 */
+		"2: cache 2, 0(%[addr])           \n" /* flush L1 VCache */
+		"   cache 2, 1(%[addr])           \n"
+		"   cache 2, 2(%[addr])           \n"
+		"   cache 2, 3(%[addr])           \n"
+		"   cache 2, 4(%[addr])           \n"
+		"   cache 2, 5(%[addr])           \n"
+		"   cache 2, 6(%[addr])           \n"
+		"   cache 2, 7(%[addr])           \n"
+		"   cache 2, 8(%[addr])           \n"
+		"   cache 2, 9(%[addr])           \n"
+		"   cache 2, 10(%[addr])          \n"
+		"   cache 2, 11(%[addr])          \n"
+		"   cache 2, 12(%[addr])          \n"
+		"   cache 2, 13(%[addr])          \n"
+		"   cache 2, 14(%[addr])          \n"
+		"   cache 2, 15(%[addr])          \n"
+		"   addiu %[vsets], %[vsets], -1  \n"
+		"   bnez  %[vsets], 2b            \n"
+		"   addiu %[addr], %[addr], 0x40  \n"
+		"   li    %[val], 0x7             \n" /* *state_addr = CPU_DEAD; */
+		"   sw    %[val], (%[state_addr]) \n"
+		"   sync                          \n"
+		"   cache 21, (%[state_addr])     \n" /* flush entry of *state_addr */
+		"   .set pop                      \n"
+		: [addr] "=&r" (addr), [val] "=&r" (val)
+		: [state_addr] "r" (state_addr),
+		  [sets] "r" (cpu_data[smp_processor_id()].dcache.sets),
+		  [vsets] "r" (cpu_data[smp_processor_id()].vcache.sets));
+
+	__asm__ __volatile__(
+		"   .set push                         \n"
+		"   .set noreorder                    \n"
+		"   .set mips64                       \n"
+		"   mfc0  %[cpuid], $15, 1            \n"
+		"   andi  %[cpuid], 0x3ff             \n"
+		"   dli   %[base], 0x900000003ff01000 \n"
+		"   andi  %[core], %[cpuid], 0x3      \n"
+		"   sll   %[core], 8                  \n" /* get core id */
+		"   or    %[base], %[base], %[core]   \n"
+		"   andi  %[node], %[cpuid], 0xc      \n"
+		"   dsll  %[node], 42                 \n" /* get node id */
+		"   or    %[base], %[base], %[node]   \n"
+		"1: li    %[count], 0x100             \n" /* wait for init loop */
+		"2: bnez  %[count], 2b                \n" /* limit mailbox access */
+		"   addiu %[count], -1                \n"
+		"   lw    %[initfunc], 0x20(%[base])  \n" /* check lower 32-bit as jump indicator */
+		"   beqz  %[initfunc], 1b             \n"
+		"   nop                               \n"
+		"   ld    %[initfunc], 0x20(%[base])  \n" /* get PC (whole 64-bit) via mailbox */
+		"   ld    $sp, 0x28(%[base])          \n" /* get SP via mailbox */
+		"   ld    $gp, 0x30(%[base])          \n" /* get GP via mailbox */
+		"   ld    $a1, 0x38(%[base])          \n"
+		"   jr    %[initfunc]                 \n" /* jump to initial PC */
+		"   nop                               \n"
+		"   .set pop                          \n"
+		: [core] "=&r" (core), [node] "=&r" (node),
+		  [base] "=&r" (base), [cpuid] "=&r" (cpuid),
+		  [count] "=&r" (count), [initfunc] "=&r" (initfunc)
+		: /* No Input */
+		: "a1");
+}
+
+void play_dead(void)
+{
+	int prid_imp, prid_rev, *state_addr;
+	unsigned int cpu = smp_processor_id();
+	void (*play_dead_at_ckseg1)(int *);
+
+	idle_task_exit();
+
+	prid_imp = read_c0_prid() & PRID_IMP_MASK;
+	prid_rev = read_c0_prid() & PRID_REV_MASK;
+
+	if (prid_imp == PRID_IMP_LOONGSON_64G) {
+		play_dead_at_ckseg1 =
+			(void *)CKSEG1ADDR((unsigned long)loongson3_type3_play_dead);
+		goto out;
+	}
+
+	switch (prid_rev) {
+	case PRID_REV_LOONGSON3A_R1:
+	default:
+		play_dead_at_ckseg1 =
+			(void *)CKSEG1ADDR((unsigned long)loongson3_type1_play_dead);
+		break;
+	case PRID_REV_LOONGSON3B_R1:
+	case PRID_REV_LOONGSON3B_R2:
+		play_dead_at_ckseg1 =
+			(void *)CKSEG1ADDR((unsigned long)loongson3_type2_play_dead);
+		break;
+	case PRID_REV_LOONGSON3A_R2_0:
+	case PRID_REV_LOONGSON3A_R2_1:
+	case PRID_REV_LOONGSON3A_R3_0:
+	case PRID_REV_LOONGSON3A_R3_1:
+		play_dead_at_ckseg1 =
+			(void *)CKSEG1ADDR((unsigned long)loongson3_type3_play_dead);
+		break;
+	}
+
+out:
+	state_addr = &per_cpu(cpu_state, cpu);
+	mb();
+	play_dead_at_ckseg1(state_addr);
+}
+
+static int loongson3_disable_clock(unsigned int cpu)
+{
+	uint64_t core_id = cpu_core(&cpu_data[cpu]);
+	uint64_t package_id = cpu_data[cpu].package;
+
+	if ((read_c0_prid() & PRID_REV_MASK) == PRID_REV_LOONGSON3A_R1) {
+		LOONGSON_CHIPCFG(package_id) &= ~(1 << (12 + core_id));
+	} else {
+		if (!(loongson_sysconf.workarounds & WORKAROUND_CPUHOTPLUG))
+			LOONGSON_FREQCTRL(package_id) &= ~(1 << (core_id * 4 + 3));
+	}
+	return 0;
+}
+
+static int loongson3_enable_clock(unsigned int cpu)
+{
+	uint64_t core_id = cpu_core(&cpu_data[cpu]);
+	uint64_t package_id = cpu_data[cpu].package;
+
+	if ((read_c0_prid() & PRID_REV_MASK) == PRID_REV_LOONGSON3A_R1) {
+		LOONGSON_CHIPCFG(package_id) |= 1 << (12 + core_id);
+	} else {
+		if (!(loongson_sysconf.workarounds & WORKAROUND_CPUHOTPLUG))
+			LOONGSON_FREQCTRL(package_id) |= 1 << (core_id * 4 + 3);
+	}
+	return 0;
+}
+
+static int register_loongson3_notifier(void)
+{
+	return cpuhp_setup_state_nocalls(CPUHP_MIPS_SOC_PREPARE,
+					 "mips/loongson:prepare",
+					 loongson3_enable_clock,
+					 loongson3_disable_clock);
+}
+early_initcall(register_loongson3_notifier);
+
+#endif
+
+const struct plat_smp_ops loongson3_smp_ops = {
+	.send_ipi_single = loongson3_send_ipi_single,
+	.send_ipi_mask = loongson3_send_ipi_mask,
+	.init_secondary = loongson3_init_secondary,
+	.smp_finish = loongson3_smp_finish,
+	.boot_secondary = loongson3_boot_secondary,
+	.smp_setup = loongson3_smp_setup,
+	.prepare_cpus = loongson3_prepare_cpus,
+#ifdef CONFIG_HOTPLUG_CPU
+	.cpu_disable = loongson3_cpu_disable,
+	.cpu_die = loongson3_cpu_die,
+#endif
+#ifdef CONFIG_KEXEC
+	.kexec_nonboot_cpu = kexec_nonboot_cpu_jump,
+#endif
+};
diff --git a/arch/mips/loongson64/smp.h b/arch/mips/loongson64/smp.h
new file mode 100644
index 000000000..957bde81e
--- /dev/null
+++ b/arch/mips/loongson64/smp.h
@@ -0,0 +1,31 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __LOONGSON_SMP_H_
+#define __LOONGSON_SMP_H_
+
+/* for Loongson-3 smp support */
+extern unsigned long long smp_group[4];
+
+/* 4 groups(nodes) in maximum in numa case */
+#define SMP_CORE_GROUP0_BASE	(smp_group[0])
+#define SMP_CORE_GROUP1_BASE	(smp_group[1])
+#define SMP_CORE_GROUP2_BASE	(smp_group[2])
+#define SMP_CORE_GROUP3_BASE	(smp_group[3])
+
+/* 4 cores in each group(node) */
+#define SMP_CORE0_OFFSET  0x000
+#define SMP_CORE1_OFFSET  0x100
+#define SMP_CORE2_OFFSET  0x200
+#define SMP_CORE3_OFFSET  0x300
+
+/* ipi registers offsets */
+#define STATUS0  0x00
+#define EN0      0x04
+#define SET0     0x08
+#define CLEAR0   0x0c
+#define STATUS1  0x10
+#define MASK1    0x14
+#define SET1     0x18
+#define CLEAR1   0x1c
+#define BUF      0x20
+
+#endif
diff --git a/arch/mips/loongson64/time.c b/arch/mips/loongson64/time.c
new file mode 100644
index 000000000..f6d2c1e30
--- /dev/null
+++ b/arch/mips/loongson64/time.c
@@ -0,0 +1,47 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2007 Lemote, Inc. & Institute of Computing Technology
+ * Author: Fuxin Zhang, zhangfx@lemote.com
+ *
+ * Copyright (C) 2009 Lemote Inc.
+ * Author: Wu Zhangjin, wuzhangjin@gmail.com
+ */
+
+#include <asm/time.h>
+#include <asm/hpet.h>
+
+#include <loongson.h>
+#include <linux/clk.h>
+#include <linux/of_clk.h>
+
+void __init plat_time_init(void)
+{
+	struct clk *clk;
+	struct device_node *np;
+
+	if (loongson_sysconf.fw_interface == LOONGSON_DTB) {
+		of_clk_init(NULL);
+
+		np = of_get_cpu_node(0, NULL);
+		if (!np) {
+			pr_err("Failed to get CPU node\n");
+			return;
+		}
+
+		clk = of_clk_get(np, 0);
+		if (IS_ERR(clk)) {
+			pr_err("Failed to get CPU clock: %ld\n", PTR_ERR(clk));
+			return;
+		}
+
+		cpu_clock_freq = clk_get_rate(clk);
+		clk_put(clk);
+	}
+
+	/* setup mips r4k timer */
+	mips_hpt_frequency = cpu_clock_freq / 2;
+
+#ifdef CONFIG_RS780_HPET
+	setup_hpet_timer();
+#endif
+}
diff --git a/arch/mips/loongson64/vbios_quirk.c b/arch/mips/loongson64/vbios_quirk.c
new file mode 100644
index 000000000..3115d4de9
--- /dev/null
+++ b/arch/mips/loongson64/vbios_quirk.c
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include <linux/pci.h>
+#include <loongson.h>
+
+static void pci_fixup_video(struct pci_dev *pdev)
+{
+	struct resource *res = &pdev->resource[PCI_ROM_RESOURCE];
+
+	if (res->start)
+		return;
+
+	if (!loongson_sysconf.vgabios_addr)
+		return;
+
+	pci_disable_rom(pdev);
+	if (res->parent)
+		release_resource(res);
+
+	res->start = virt_to_phys((void *) loongson_sysconf.vgabios_addr);
+	res->end   = res->start + 256*1024 - 1;
+	res->flags = IORESOURCE_MEM | IORESOURCE_ROM_SHADOW |
+		     IORESOURCE_PCI_FIXED;
+
+	dev_info(&pdev->dev, "Video device with shadowed ROM at %pR\n", res);
+}
+DECLARE_PCI_FIXUP_CLASS_HEADER(PCI_VENDOR_ID_ATI, 0x9615,
+			       PCI_CLASS_DISPLAY_VGA, 8, pci_fixup_video);
diff --git a/arch/mips/math-emu/Makefile b/arch/mips/math-emu/Makefile
new file mode 100644
index 000000000..81d25ff32
--- /dev/null
+++ b/arch/mips/math-emu/Makefile
@@ -0,0 +1,19 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Makefile for the Linux/MIPS kernel FPU emulation.
+#
+
+obj-y	+= cp1emu.o ieee754dp.o ieee754sp.o ieee754.o \
+	   dp_div.o dp_mul.o dp_sub.o dp_add.o dp_fsp.o dp_cmp.o dp_simple.o \
+	   dp_tint.o dp_fint.o dp_rint.o dp_maddf.o dp_2008class.o dp_fmin.o \
+	   dp_fmax.o							     \
+	   sp_div.o sp_mul.o sp_sub.o sp_add.o sp_fdp.o sp_cmp.o sp_simple.o \
+	   sp_tint.o sp_fint.o sp_rint.o sp_maddf.o sp_2008class.o sp_fmin.o \
+	   sp_fmax.o							     \
+	   dsemul.o
+
+lib-y	+= ieee754d.o \
+	   dp_tlong.o dp_flong.o dp_sqrt.o \
+	   sp_tlong.o sp_flong.o sp_sqrt.o
+
+obj-$(CONFIG_DEBUG_FS) += me-debugfs.o
diff --git a/arch/mips/math-emu/cp1emu.c b/arch/mips/math-emu/cp1emu.c
new file mode 100644
index 000000000..265bc5781
--- /dev/null
+++ b/arch/mips/math-emu/cp1emu.c
@@ -0,0 +1,2948 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * cp1emu.c: a MIPS coprocessor 1 (FPU) instruction emulator
+ *
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ *
+ * Kevin D. Kissell, kevink@mips.com and Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 2000  MIPS Technologies, Inc.
+ *
+ * A complete emulator for MIPS coprocessor 1 instructions.  This is
+ * required for #float(switch) or #float(trap), where it catches all
+ * COP1 instructions via the "CoProcessor Unusable" exception.
+ *
+ * More surprisingly it is also required for #float(ieee), to help out
+ * the hardware FPU at the boundaries of the IEEE-754 representation
+ * (denormalised values, infinities, underflow, etc).  It is made
+ * quite nasty because emulation of some non-COP1 instructions is
+ * required, e.g. in branch delay slots.
+ *
+ * Note if you know that you won't have an FPU, then you'll get much
+ * better performance by compiling with -msoft-float!
+ */
+#include <linux/sched.h>
+#include <linux/debugfs.h>
+#include <linux/percpu-defs.h>
+#include <linux/perf_event.h>
+
+#include <asm/branch.h>
+#include <asm/inst.h>
+#include <asm/ptrace.h>
+#include <asm/signal.h>
+#include <linux/uaccess.h>
+
+#include <asm/cpu-info.h>
+#include <asm/processor.h>
+#include <asm/fpu_emulator.h>
+#include <asm/fpu.h>
+#include <asm/mips-r2-to-r6-emul.h>
+
+#include "ieee754.h"
+
+/* Function which emulates a floating point instruction. */
+
+static int fpu_emu(struct pt_regs *, struct mips_fpu_struct *,
+	mips_instruction);
+
+static int fpux_emu(struct pt_regs *,
+	struct mips_fpu_struct *, mips_instruction, void __user **);
+
+/* Control registers */
+
+#define FPCREG_RID	0	/* $0  = revision id */
+#define FPCREG_FCCR	25	/* $25 = fccr */
+#define FPCREG_FEXR	26	/* $26 = fexr */
+#define FPCREG_FENR	28	/* $28 = fenr */
+#define FPCREG_CSR	31	/* $31 = csr */
+
+/* convert condition code register number to csr bit */
+const unsigned int fpucondbit[8] = {
+	FPU_CSR_COND,
+	FPU_CSR_COND1,
+	FPU_CSR_COND2,
+	FPU_CSR_COND3,
+	FPU_CSR_COND4,
+	FPU_CSR_COND5,
+	FPU_CSR_COND6,
+	FPU_CSR_COND7
+};
+
+/* (microMIPS) Convert certain microMIPS instructions to MIPS32 format. */
+static const int sd_format[] = {16, 17, 0, 0, 0, 0, 0, 0};
+static const int sdps_format[] = {16, 17, 22, 0, 0, 0, 0, 0};
+static const int dwl_format[] = {17, 20, 21, 0, 0, 0, 0, 0};
+static const int swl_format[] = {16, 20, 21, 0, 0, 0, 0, 0};
+
+/*
+ * This functions translates a 32-bit microMIPS instruction
+ * into a 32-bit MIPS32 instruction. Returns 0 on success
+ * and SIGILL otherwise.
+ */
+static int microMIPS32_to_MIPS32(union mips_instruction *insn_ptr)
+{
+	union mips_instruction insn = *insn_ptr;
+	union mips_instruction mips32_insn = insn;
+	int func, fmt, op;
+
+	switch (insn.mm_i_format.opcode) {
+	case mm_ldc132_op:
+		mips32_insn.mm_i_format.opcode = ldc1_op;
+		mips32_insn.mm_i_format.rt = insn.mm_i_format.rs;
+		mips32_insn.mm_i_format.rs = insn.mm_i_format.rt;
+		break;
+	case mm_lwc132_op:
+		mips32_insn.mm_i_format.opcode = lwc1_op;
+		mips32_insn.mm_i_format.rt = insn.mm_i_format.rs;
+		mips32_insn.mm_i_format.rs = insn.mm_i_format.rt;
+		break;
+	case mm_sdc132_op:
+		mips32_insn.mm_i_format.opcode = sdc1_op;
+		mips32_insn.mm_i_format.rt = insn.mm_i_format.rs;
+		mips32_insn.mm_i_format.rs = insn.mm_i_format.rt;
+		break;
+	case mm_swc132_op:
+		mips32_insn.mm_i_format.opcode = swc1_op;
+		mips32_insn.mm_i_format.rt = insn.mm_i_format.rs;
+		mips32_insn.mm_i_format.rs = insn.mm_i_format.rt;
+		break;
+	case mm_pool32i_op:
+		/* NOTE: offset is << by 1 if in microMIPS mode. */
+		if ((insn.mm_i_format.rt == mm_bc1f_op) ||
+		    (insn.mm_i_format.rt == mm_bc1t_op)) {
+			mips32_insn.fb_format.opcode = cop1_op;
+			mips32_insn.fb_format.bc = bc_op;
+			mips32_insn.fb_format.flag =
+				(insn.mm_i_format.rt == mm_bc1t_op) ? 1 : 0;
+		} else
+			return SIGILL;
+		break;
+	case mm_pool32f_op:
+		switch (insn.mm_fp0_format.func) {
+		case mm_32f_01_op:
+		case mm_32f_11_op:
+		case mm_32f_02_op:
+		case mm_32f_12_op:
+		case mm_32f_41_op:
+		case mm_32f_51_op:
+		case mm_32f_42_op:
+		case mm_32f_52_op:
+			op = insn.mm_fp0_format.func;
+			if (op == mm_32f_01_op)
+				func = madd_s_op;
+			else if (op == mm_32f_11_op)
+				func = madd_d_op;
+			else if (op == mm_32f_02_op)
+				func = nmadd_s_op;
+			else if (op == mm_32f_12_op)
+				func = nmadd_d_op;
+			else if (op == mm_32f_41_op)
+				func = msub_s_op;
+			else if (op == mm_32f_51_op)
+				func = msub_d_op;
+			else if (op == mm_32f_42_op)
+				func = nmsub_s_op;
+			else
+				func = nmsub_d_op;
+			mips32_insn.fp6_format.opcode = cop1x_op;
+			mips32_insn.fp6_format.fr = insn.mm_fp6_format.fr;
+			mips32_insn.fp6_format.ft = insn.mm_fp6_format.ft;
+			mips32_insn.fp6_format.fs = insn.mm_fp6_format.fs;
+			mips32_insn.fp6_format.fd = insn.mm_fp6_format.fd;
+			mips32_insn.fp6_format.func = func;
+			break;
+		case mm_32f_10_op:
+			func = -1;	/* Invalid */
+			op = insn.mm_fp5_format.op & 0x7;
+			if (op == mm_ldxc1_op)
+				func = ldxc1_op;
+			else if (op == mm_sdxc1_op)
+				func = sdxc1_op;
+			else if (op == mm_lwxc1_op)
+				func = lwxc1_op;
+			else if (op == mm_swxc1_op)
+				func = swxc1_op;
+
+			if (func != -1) {
+				mips32_insn.r_format.opcode = cop1x_op;
+				mips32_insn.r_format.rs =
+					insn.mm_fp5_format.base;
+				mips32_insn.r_format.rt =
+					insn.mm_fp5_format.index;
+				mips32_insn.r_format.rd = 0;
+				mips32_insn.r_format.re = insn.mm_fp5_format.fd;
+				mips32_insn.r_format.func = func;
+			} else
+				return SIGILL;
+			break;
+		case mm_32f_40_op:
+			op = -1;	/* Invalid */
+			if (insn.mm_fp2_format.op == mm_fmovt_op)
+				op = 1;
+			else if (insn.mm_fp2_format.op == mm_fmovf_op)
+				op = 0;
+			if (op != -1) {
+				mips32_insn.fp0_format.opcode = cop1_op;
+				mips32_insn.fp0_format.fmt =
+					sdps_format[insn.mm_fp2_format.fmt];
+				mips32_insn.fp0_format.ft =
+					(insn.mm_fp2_format.cc<<2) + op;
+				mips32_insn.fp0_format.fs =
+					insn.mm_fp2_format.fs;
+				mips32_insn.fp0_format.fd =
+					insn.mm_fp2_format.fd;
+				mips32_insn.fp0_format.func = fmovc_op;
+			} else
+				return SIGILL;
+			break;
+		case mm_32f_60_op:
+			func = -1;	/* Invalid */
+			if (insn.mm_fp0_format.op == mm_fadd_op)
+				func = fadd_op;
+			else if (insn.mm_fp0_format.op == mm_fsub_op)
+				func = fsub_op;
+			else if (insn.mm_fp0_format.op == mm_fmul_op)
+				func = fmul_op;
+			else if (insn.mm_fp0_format.op == mm_fdiv_op)
+				func = fdiv_op;
+			if (func != -1) {
+				mips32_insn.fp0_format.opcode = cop1_op;
+				mips32_insn.fp0_format.fmt =
+					sdps_format[insn.mm_fp0_format.fmt];
+				mips32_insn.fp0_format.ft =
+					insn.mm_fp0_format.ft;
+				mips32_insn.fp0_format.fs =
+					insn.mm_fp0_format.fs;
+				mips32_insn.fp0_format.fd =
+					insn.mm_fp0_format.fd;
+				mips32_insn.fp0_format.func = func;
+			} else
+				return SIGILL;
+			break;
+		case mm_32f_70_op:
+			func = -1;	/* Invalid */
+			if (insn.mm_fp0_format.op == mm_fmovn_op)
+				func = fmovn_op;
+			else if (insn.mm_fp0_format.op == mm_fmovz_op)
+				func = fmovz_op;
+			if (func != -1) {
+				mips32_insn.fp0_format.opcode = cop1_op;
+				mips32_insn.fp0_format.fmt =
+					sdps_format[insn.mm_fp0_format.fmt];
+				mips32_insn.fp0_format.ft =
+					insn.mm_fp0_format.ft;
+				mips32_insn.fp0_format.fs =
+					insn.mm_fp0_format.fs;
+				mips32_insn.fp0_format.fd =
+					insn.mm_fp0_format.fd;
+				mips32_insn.fp0_format.func = func;
+			} else
+				return SIGILL;
+			break;
+		case mm_32f_73_op:    /* POOL32FXF */
+			switch (insn.mm_fp1_format.op) {
+			case mm_movf0_op:
+			case mm_movf1_op:
+			case mm_movt0_op:
+			case mm_movt1_op:
+				if ((insn.mm_fp1_format.op & 0x7f) ==
+				    mm_movf0_op)
+					op = 0;
+				else
+					op = 1;
+				mips32_insn.r_format.opcode = spec_op;
+				mips32_insn.r_format.rs = insn.mm_fp4_format.fs;
+				mips32_insn.r_format.rt =
+					(insn.mm_fp4_format.cc << 2) + op;
+				mips32_insn.r_format.rd = insn.mm_fp4_format.rt;
+				mips32_insn.r_format.re = 0;
+				mips32_insn.r_format.func = movc_op;
+				break;
+			case mm_fcvtd0_op:
+			case mm_fcvtd1_op:
+			case mm_fcvts0_op:
+			case mm_fcvts1_op:
+				if ((insn.mm_fp1_format.op & 0x7f) ==
+				    mm_fcvtd0_op) {
+					func = fcvtd_op;
+					fmt = swl_format[insn.mm_fp3_format.fmt];
+				} else {
+					func = fcvts_op;
+					fmt = dwl_format[insn.mm_fp3_format.fmt];
+				}
+				mips32_insn.fp0_format.opcode = cop1_op;
+				mips32_insn.fp0_format.fmt = fmt;
+				mips32_insn.fp0_format.ft = 0;
+				mips32_insn.fp0_format.fs =
+					insn.mm_fp3_format.fs;
+				mips32_insn.fp0_format.fd =
+					insn.mm_fp3_format.rt;
+				mips32_insn.fp0_format.func = func;
+				break;
+			case mm_fmov0_op:
+			case mm_fmov1_op:
+			case mm_fabs0_op:
+			case mm_fabs1_op:
+			case mm_fneg0_op:
+			case mm_fneg1_op:
+				if ((insn.mm_fp1_format.op & 0x7f) ==
+				    mm_fmov0_op)
+					func = fmov_op;
+				else if ((insn.mm_fp1_format.op & 0x7f) ==
+					 mm_fabs0_op)
+					func = fabs_op;
+				else
+					func = fneg_op;
+				mips32_insn.fp0_format.opcode = cop1_op;
+				mips32_insn.fp0_format.fmt =
+					sdps_format[insn.mm_fp3_format.fmt];
+				mips32_insn.fp0_format.ft = 0;
+				mips32_insn.fp0_format.fs =
+					insn.mm_fp3_format.fs;
+				mips32_insn.fp0_format.fd =
+					insn.mm_fp3_format.rt;
+				mips32_insn.fp0_format.func = func;
+				break;
+			case mm_ffloorl_op:
+			case mm_ffloorw_op:
+			case mm_fceill_op:
+			case mm_fceilw_op:
+			case mm_ftruncl_op:
+			case mm_ftruncw_op:
+			case mm_froundl_op:
+			case mm_froundw_op:
+			case mm_fcvtl_op:
+			case mm_fcvtw_op:
+				if (insn.mm_fp1_format.op == mm_ffloorl_op)
+					func = ffloorl_op;
+				else if (insn.mm_fp1_format.op == mm_ffloorw_op)
+					func = ffloor_op;
+				else if (insn.mm_fp1_format.op == mm_fceill_op)
+					func = fceill_op;
+				else if (insn.mm_fp1_format.op == mm_fceilw_op)
+					func = fceil_op;
+				else if (insn.mm_fp1_format.op == mm_ftruncl_op)
+					func = ftruncl_op;
+				else if (insn.mm_fp1_format.op == mm_ftruncw_op)
+					func = ftrunc_op;
+				else if (insn.mm_fp1_format.op == mm_froundl_op)
+					func = froundl_op;
+				else if (insn.mm_fp1_format.op == mm_froundw_op)
+					func = fround_op;
+				else if (insn.mm_fp1_format.op == mm_fcvtl_op)
+					func = fcvtl_op;
+				else
+					func = fcvtw_op;
+				mips32_insn.fp0_format.opcode = cop1_op;
+				mips32_insn.fp0_format.fmt =
+					sd_format[insn.mm_fp1_format.fmt];
+				mips32_insn.fp0_format.ft = 0;
+				mips32_insn.fp0_format.fs =
+					insn.mm_fp1_format.fs;
+				mips32_insn.fp0_format.fd =
+					insn.mm_fp1_format.rt;
+				mips32_insn.fp0_format.func = func;
+				break;
+			case mm_frsqrt_op:
+			case mm_fsqrt_op:
+			case mm_frecip_op:
+				if (insn.mm_fp1_format.op == mm_frsqrt_op)
+					func = frsqrt_op;
+				else if (insn.mm_fp1_format.op == mm_fsqrt_op)
+					func = fsqrt_op;
+				else
+					func = frecip_op;
+				mips32_insn.fp0_format.opcode = cop1_op;
+				mips32_insn.fp0_format.fmt =
+					sdps_format[insn.mm_fp1_format.fmt];
+				mips32_insn.fp0_format.ft = 0;
+				mips32_insn.fp0_format.fs =
+					insn.mm_fp1_format.fs;
+				mips32_insn.fp0_format.fd =
+					insn.mm_fp1_format.rt;
+				mips32_insn.fp0_format.func = func;
+				break;
+			case mm_mfc1_op:
+			case mm_mtc1_op:
+			case mm_cfc1_op:
+			case mm_ctc1_op:
+			case mm_mfhc1_op:
+			case mm_mthc1_op:
+				if (insn.mm_fp1_format.op == mm_mfc1_op)
+					op = mfc_op;
+				else if (insn.mm_fp1_format.op == mm_mtc1_op)
+					op = mtc_op;
+				else if (insn.mm_fp1_format.op == mm_cfc1_op)
+					op = cfc_op;
+				else if (insn.mm_fp1_format.op == mm_ctc1_op)
+					op = ctc_op;
+				else if (insn.mm_fp1_format.op == mm_mfhc1_op)
+					op = mfhc_op;
+				else
+					op = mthc_op;
+				mips32_insn.fp1_format.opcode = cop1_op;
+				mips32_insn.fp1_format.op = op;
+				mips32_insn.fp1_format.rt =
+					insn.mm_fp1_format.rt;
+				mips32_insn.fp1_format.fs =
+					insn.mm_fp1_format.fs;
+				mips32_insn.fp1_format.fd = 0;
+				mips32_insn.fp1_format.func = 0;
+				break;
+			default:
+				return SIGILL;
+			}
+			break;
+		case mm_32f_74_op:	/* c.cond.fmt */
+			mips32_insn.fp0_format.opcode = cop1_op;
+			mips32_insn.fp0_format.fmt =
+				sdps_format[insn.mm_fp4_format.fmt];
+			mips32_insn.fp0_format.ft = insn.mm_fp4_format.rt;
+			mips32_insn.fp0_format.fs = insn.mm_fp4_format.fs;
+			mips32_insn.fp0_format.fd = insn.mm_fp4_format.cc << 2;
+			mips32_insn.fp0_format.func =
+				insn.mm_fp4_format.cond | MM_MIPS32_COND_FC;
+			break;
+		default:
+			return SIGILL;
+		}
+		break;
+	default:
+		return SIGILL;
+	}
+
+	*insn_ptr = mips32_insn;
+	return 0;
+}
+
+/*
+ * Redundant with logic already in kernel/branch.c,
+ * embedded in compute_return_epc.  At some point,
+ * a single subroutine should be used across both
+ * modules.
+ */
+int isBranchInstr(struct pt_regs *regs, struct mm_decoded_insn dec_insn,
+		  unsigned long *contpc)
+{
+	union mips_instruction insn = (union mips_instruction)dec_insn.insn;
+	unsigned int fcr31;
+	unsigned int bit = 0;
+	unsigned int bit0;
+	union fpureg *fpr;
+
+	switch (insn.i_format.opcode) {
+	case spec_op:
+		switch (insn.r_format.func) {
+		case jalr_op:
+			if (insn.r_format.rd != 0) {
+				regs->regs[insn.r_format.rd] =
+					regs->cp0_epc + dec_insn.pc_inc +
+					dec_insn.next_pc_inc;
+			}
+			fallthrough;
+		case jr_op:
+			/* For R6, JR already emulated in jalr_op */
+			if (NO_R6EMU && insn.r_format.func == jr_op)
+				break;
+			*contpc = regs->regs[insn.r_format.rs];
+			return 1;
+		}
+		break;
+	case bcond_op:
+		switch (insn.i_format.rt) {
+		case bltzal_op:
+		case bltzall_op:
+			if (NO_R6EMU && (insn.i_format.rs ||
+			    insn.i_format.rt == bltzall_op))
+				break;
+
+			regs->regs[31] = regs->cp0_epc +
+				dec_insn.pc_inc +
+				dec_insn.next_pc_inc;
+			fallthrough;
+		case bltzl_op:
+			if (NO_R6EMU)
+				break;
+			fallthrough;
+		case bltz_op:
+			if ((long)regs->regs[insn.i_format.rs] < 0)
+				*contpc = regs->cp0_epc +
+					dec_insn.pc_inc +
+					(insn.i_format.simmediate << 2);
+			else
+				*contpc = regs->cp0_epc +
+					dec_insn.pc_inc +
+					dec_insn.next_pc_inc;
+			return 1;
+		case bgezal_op:
+		case bgezall_op:
+			if (NO_R6EMU && (insn.i_format.rs ||
+			    insn.i_format.rt == bgezall_op))
+				break;
+
+			regs->regs[31] = regs->cp0_epc +
+				dec_insn.pc_inc +
+				dec_insn.next_pc_inc;
+			fallthrough;
+		case bgezl_op:
+			if (NO_R6EMU)
+				break;
+			fallthrough;
+		case bgez_op:
+			if ((long)regs->regs[insn.i_format.rs] >= 0)
+				*contpc = regs->cp0_epc +
+					dec_insn.pc_inc +
+					(insn.i_format.simmediate << 2);
+			else
+				*contpc = regs->cp0_epc +
+					dec_insn.pc_inc +
+					dec_insn.next_pc_inc;
+			return 1;
+		}
+		break;
+	case jalx_op:
+		set_isa16_mode(bit);
+		fallthrough;
+	case jal_op:
+		regs->regs[31] = regs->cp0_epc +
+			dec_insn.pc_inc +
+			dec_insn.next_pc_inc;
+		fallthrough;
+	case j_op:
+		*contpc = regs->cp0_epc + dec_insn.pc_inc;
+		*contpc >>= 28;
+		*contpc <<= 28;
+		*contpc |= (insn.j_format.target << 2);
+		/* Set microMIPS mode bit: XOR for jalx. */
+		*contpc ^= bit;
+		return 1;
+	case beql_op:
+		if (NO_R6EMU)
+			break;
+		fallthrough;
+	case beq_op:
+		if (regs->regs[insn.i_format.rs] ==
+		    regs->regs[insn.i_format.rt])
+			*contpc = regs->cp0_epc +
+				dec_insn.pc_inc +
+				(insn.i_format.simmediate << 2);
+		else
+			*contpc = regs->cp0_epc +
+				dec_insn.pc_inc +
+				dec_insn.next_pc_inc;
+		return 1;
+	case bnel_op:
+		if (NO_R6EMU)
+			break;
+		fallthrough;
+	case bne_op:
+		if (regs->regs[insn.i_format.rs] !=
+		    regs->regs[insn.i_format.rt])
+			*contpc = regs->cp0_epc +
+				dec_insn.pc_inc +
+				(insn.i_format.simmediate << 2);
+		else
+			*contpc = regs->cp0_epc +
+				dec_insn.pc_inc +
+				dec_insn.next_pc_inc;
+		return 1;
+	case blezl_op:
+		if (!insn.i_format.rt && NO_R6EMU)
+			break;
+		fallthrough;
+	case blez_op:
+
+		/*
+		 * Compact branches for R6 for the
+		 * blez and blezl opcodes.
+		 * BLEZ  | rs = 0 | rt != 0  == BLEZALC
+		 * BLEZ  | rs = rt != 0      == BGEZALC
+		 * BLEZ  | rs != 0 | rt != 0 == BGEUC
+		 * BLEZL | rs = 0 | rt != 0  == BLEZC
+		 * BLEZL | rs = rt != 0      == BGEZC
+		 * BLEZL | rs != 0 | rt != 0 == BGEC
+		 *
+		 * For real BLEZ{,L}, rt is always 0.
+		 */
+		if (cpu_has_mips_r6 && insn.i_format.rt) {
+			if ((insn.i_format.opcode == blez_op) &&
+			    ((!insn.i_format.rs && insn.i_format.rt) ||
+			     (insn.i_format.rs == insn.i_format.rt)))
+				regs->regs[31] = regs->cp0_epc +
+					dec_insn.pc_inc;
+			*contpc = regs->cp0_epc + dec_insn.pc_inc +
+				dec_insn.next_pc_inc;
+
+			return 1;
+		}
+		if ((long)regs->regs[insn.i_format.rs] <= 0)
+			*contpc = regs->cp0_epc +
+				dec_insn.pc_inc +
+				(insn.i_format.simmediate << 2);
+		else
+			*contpc = regs->cp0_epc +
+				dec_insn.pc_inc +
+				dec_insn.next_pc_inc;
+		return 1;
+	case bgtzl_op:
+		if (!insn.i_format.rt && NO_R6EMU)
+			break;
+		fallthrough;
+	case bgtz_op:
+		/*
+		 * Compact branches for R6 for the
+		 * bgtz and bgtzl opcodes.
+		 * BGTZ  | rs = 0 | rt != 0  == BGTZALC
+		 * BGTZ  | rs = rt != 0      == BLTZALC
+		 * BGTZ  | rs != 0 | rt != 0 == BLTUC
+		 * BGTZL | rs = 0 | rt != 0  == BGTZC
+		 * BGTZL | rs = rt != 0      == BLTZC
+		 * BGTZL | rs != 0 | rt != 0 == BLTC
+		 *
+		 * *ZALC varint for BGTZ &&& rt != 0
+		 * For real GTZ{,L}, rt is always 0.
+		 */
+		if (cpu_has_mips_r6 && insn.i_format.rt) {
+			if ((insn.i_format.opcode == blez_op) &&
+			    ((!insn.i_format.rs && insn.i_format.rt) ||
+			     (insn.i_format.rs == insn.i_format.rt)))
+				regs->regs[31] = regs->cp0_epc +
+					dec_insn.pc_inc;
+			*contpc = regs->cp0_epc + dec_insn.pc_inc +
+				dec_insn.next_pc_inc;
+
+			return 1;
+		}
+
+		if ((long)regs->regs[insn.i_format.rs] > 0)
+			*contpc = regs->cp0_epc +
+				dec_insn.pc_inc +
+				(insn.i_format.simmediate << 2);
+		else
+			*contpc = regs->cp0_epc +
+				dec_insn.pc_inc +
+				dec_insn.next_pc_inc;
+		return 1;
+	case pop10_op:
+	case pop30_op:
+		if (!cpu_has_mips_r6)
+			break;
+		if (insn.i_format.rt && !insn.i_format.rs)
+			regs->regs[31] = regs->cp0_epc + 4;
+		*contpc = regs->cp0_epc + dec_insn.pc_inc +
+			dec_insn.next_pc_inc;
+
+		return 1;
+#ifdef CONFIG_CPU_CAVIUM_OCTEON
+	case lwc2_op: /* This is bbit0 on Octeon */
+		if ((regs->regs[insn.i_format.rs] & (1ull<<insn.i_format.rt)) == 0)
+			*contpc = regs->cp0_epc + 4 + (insn.i_format.simmediate << 2);
+		else
+			*contpc = regs->cp0_epc + 8;
+		return 1;
+	case ldc2_op: /* This is bbit032 on Octeon */
+		if ((regs->regs[insn.i_format.rs] & (1ull<<(insn.i_format.rt + 32))) == 0)
+			*contpc = regs->cp0_epc + 4 + (insn.i_format.simmediate << 2);
+		else
+			*contpc = regs->cp0_epc + 8;
+		return 1;
+	case swc2_op: /* This is bbit1 on Octeon */
+		if (regs->regs[insn.i_format.rs] & (1ull<<insn.i_format.rt))
+			*contpc = regs->cp0_epc + 4 + (insn.i_format.simmediate << 2);
+		else
+			*contpc = regs->cp0_epc + 8;
+		return 1;
+	case sdc2_op: /* This is bbit132 on Octeon */
+		if (regs->regs[insn.i_format.rs] & (1ull<<(insn.i_format.rt + 32)))
+			*contpc = regs->cp0_epc + 4 + (insn.i_format.simmediate << 2);
+		else
+			*contpc = regs->cp0_epc + 8;
+		return 1;
+#else
+	case bc6_op:
+		/*
+		 * Only valid for MIPS R6 but we can still end up
+		 * here from a broken userland so just tell emulator
+		 * this is not a branch and let it break later on.
+		 */
+		if  (!cpu_has_mips_r6)
+			break;
+		*contpc = regs->cp0_epc + dec_insn.pc_inc +
+			dec_insn.next_pc_inc;
+
+		return 1;
+	case balc6_op:
+		if (!cpu_has_mips_r6)
+			break;
+		regs->regs[31] = regs->cp0_epc + 4;
+		*contpc = regs->cp0_epc + dec_insn.pc_inc +
+			dec_insn.next_pc_inc;
+
+		return 1;
+	case pop66_op:
+		if (!cpu_has_mips_r6)
+			break;
+		*contpc = regs->cp0_epc + dec_insn.pc_inc +
+			dec_insn.next_pc_inc;
+
+		return 1;
+	case pop76_op:
+		if (!cpu_has_mips_r6)
+			break;
+		if (!insn.i_format.rs)
+			regs->regs[31] = regs->cp0_epc + 4;
+		*contpc = regs->cp0_epc + dec_insn.pc_inc +
+			dec_insn.next_pc_inc;
+
+		return 1;
+#endif
+	case cop0_op:
+	case cop1_op:
+		/* Need to check for R6 bc1nez and bc1eqz branches */
+		if (cpu_has_mips_r6 &&
+		    ((insn.i_format.rs == bc1eqz_op) ||
+		     (insn.i_format.rs == bc1nez_op))) {
+			bit = 0;
+			fpr = &current->thread.fpu.fpr[insn.i_format.rt];
+			bit0 = get_fpr32(fpr, 0) & 0x1;
+			switch (insn.i_format.rs) {
+			case bc1eqz_op:
+				bit = bit0 == 0;
+				break;
+			case bc1nez_op:
+				bit = bit0 != 0;
+				break;
+			}
+			if (bit)
+				*contpc = regs->cp0_epc +
+					dec_insn.pc_inc +
+					(insn.i_format.simmediate << 2);
+			else
+				*contpc = regs->cp0_epc +
+					dec_insn.pc_inc +
+					dec_insn.next_pc_inc;
+
+			return 1;
+		}
+		/* R2/R6 compatible cop1 instruction */
+		fallthrough;
+	case cop2_op:
+	case cop1x_op:
+		if (insn.i_format.rs == bc_op) {
+			preempt_disable();
+			if (is_fpu_owner())
+			        fcr31 = read_32bit_cp1_register(CP1_STATUS);
+			else
+				fcr31 = current->thread.fpu.fcr31;
+			preempt_enable();
+
+			bit = (insn.i_format.rt >> 2);
+			bit += (bit != 0);
+			bit += 23;
+			switch (insn.i_format.rt & 3) {
+			case 0:	/* bc1f */
+			case 2:	/* bc1fl */
+				if (~fcr31 & (1 << bit))
+					*contpc = regs->cp0_epc +
+						dec_insn.pc_inc +
+						(insn.i_format.simmediate << 2);
+				else
+					*contpc = regs->cp0_epc +
+						dec_insn.pc_inc +
+						dec_insn.next_pc_inc;
+				return 1;
+			case 1:	/* bc1t */
+			case 3:	/* bc1tl */
+				if (fcr31 & (1 << bit))
+					*contpc = regs->cp0_epc +
+						dec_insn.pc_inc +
+						(insn.i_format.simmediate << 2);
+				else
+					*contpc = regs->cp0_epc +
+						dec_insn.pc_inc +
+						dec_insn.next_pc_inc;
+				return 1;
+			}
+		}
+		break;
+	}
+	return 0;
+}
+
+/*
+ * In the Linux kernel, we support selection of FPR format on the
+ * basis of the Status.FR bit.	If an FPU is not present, the FR bit
+ * is hardwired to zero, which would imply a 32-bit FPU even for
+ * 64-bit CPUs so we rather look at TIF_32BIT_FPREGS.
+ * FPU emu is slow and bulky and optimizing this function offers fairly
+ * sizeable benefits so we try to be clever and make this function return
+ * a constant whenever possible, that is on 64-bit kernels without O32
+ * compatibility enabled and on 32-bit without 64-bit FPU support.
+ */
+static inline int cop1_64bit(struct pt_regs *xcp)
+{
+	if (IS_ENABLED(CONFIG_64BIT) && !IS_ENABLED(CONFIG_MIPS32_O32))
+		return 1;
+	else if (IS_ENABLED(CONFIG_32BIT) &&
+		 !IS_ENABLED(CONFIG_MIPS_O32_FP64_SUPPORT))
+		return 0;
+
+	return !test_thread_flag(TIF_32BIT_FPREGS);
+}
+
+static inline bool hybrid_fprs(void)
+{
+	return test_thread_flag(TIF_HYBRID_FPREGS);
+}
+
+#define SIFROMREG(si, x)						\
+do {									\
+	if (cop1_64bit(xcp) && !hybrid_fprs())				\
+		(si) = (int)get_fpr32(&ctx->fpr[x], 0);			\
+	else								\
+		(si) = (int)get_fpr32(&ctx->fpr[(x) & ~1], (x) & 1);	\
+} while (0)
+
+#define SITOREG(si, x)							\
+do {									\
+	if (cop1_64bit(xcp) && !hybrid_fprs()) {			\
+		unsigned int i;						\
+		set_fpr32(&ctx->fpr[x], 0, si);				\
+		for (i = 1; i < ARRAY_SIZE(ctx->fpr[x].val32); i++)	\
+			set_fpr32(&ctx->fpr[x], i, 0);			\
+	} else {							\
+		set_fpr32(&ctx->fpr[(x) & ~1], (x) & 1, si);		\
+	}								\
+} while (0)
+
+#define SIFROMHREG(si, x)	((si) = (int)get_fpr32(&ctx->fpr[x], 1))
+
+#define SITOHREG(si, x)							\
+do {									\
+	unsigned int i;							\
+	set_fpr32(&ctx->fpr[x], 1, si);					\
+	for (i = 2; i < ARRAY_SIZE(ctx->fpr[x].val32); i++)		\
+		set_fpr32(&ctx->fpr[x], i, 0);				\
+} while (0)
+
+#define DIFROMREG(di, x)						\
+	((di) = get_fpr64(&ctx->fpr[(x) & ~(cop1_64bit(xcp) ^ 1)], 0))
+
+#define DITOREG(di, x)							\
+do {									\
+	unsigned int fpr, i;						\
+	fpr = (x) & ~(cop1_64bit(xcp) ^ 1);				\
+	set_fpr64(&ctx->fpr[fpr], 0, di);				\
+	for (i = 1; i < ARRAY_SIZE(ctx->fpr[x].val64); i++)		\
+		set_fpr64(&ctx->fpr[fpr], i, 0);			\
+} while (0)
+
+#define SPFROMREG(sp, x) SIFROMREG((sp).bits, x)
+#define SPTOREG(sp, x)	SITOREG((sp).bits, x)
+#define DPFROMREG(dp, x)	DIFROMREG((dp).bits, x)
+#define DPTOREG(dp, x)	DITOREG((dp).bits, x)
+
+/*
+ * Emulate a CFC1 instruction.
+ */
+static inline void cop1_cfc(struct pt_regs *xcp, struct mips_fpu_struct *ctx,
+			    mips_instruction ir)
+{
+	u32 fcr31 = ctx->fcr31;
+	u32 value = 0;
+
+	switch (MIPSInst_RD(ir)) {
+	case FPCREG_CSR:
+		value = fcr31;
+		pr_debug("%p gpr[%d]<-csr=%08x\n",
+			 (void *)xcp->cp0_epc, MIPSInst_RT(ir), value);
+		break;
+
+	case FPCREG_FENR:
+		if (!cpu_has_mips_r)
+			break;
+		value = (fcr31 >> (FPU_CSR_FS_S - MIPS_FENR_FS_S)) &
+			MIPS_FENR_FS;
+		value |= fcr31 & (FPU_CSR_ALL_E | FPU_CSR_RM);
+		pr_debug("%p gpr[%d]<-enr=%08x\n",
+			 (void *)xcp->cp0_epc, MIPSInst_RT(ir), value);
+		break;
+
+	case FPCREG_FEXR:
+		if (!cpu_has_mips_r)
+			break;
+		value = fcr31 & (FPU_CSR_ALL_X | FPU_CSR_ALL_S);
+		pr_debug("%p gpr[%d]<-exr=%08x\n",
+			 (void *)xcp->cp0_epc, MIPSInst_RT(ir), value);
+		break;
+
+	case FPCREG_FCCR:
+		if (!cpu_has_mips_r)
+			break;
+		value = (fcr31 >> (FPU_CSR_COND_S - MIPS_FCCR_COND0_S)) &
+			MIPS_FCCR_COND0;
+		value |= (fcr31 >> (FPU_CSR_COND1_S - MIPS_FCCR_COND1_S)) &
+			 (MIPS_FCCR_CONDX & ~MIPS_FCCR_COND0);
+		pr_debug("%p gpr[%d]<-ccr=%08x\n",
+			 (void *)xcp->cp0_epc, MIPSInst_RT(ir), value);
+		break;
+
+	case FPCREG_RID:
+		value = boot_cpu_data.fpu_id;
+		break;
+
+	default:
+		break;
+	}
+
+	if (MIPSInst_RT(ir))
+		xcp->regs[MIPSInst_RT(ir)] = value;
+}
+
+/*
+ * Emulate a CTC1 instruction.
+ */
+static inline void cop1_ctc(struct pt_regs *xcp, struct mips_fpu_struct *ctx,
+			    mips_instruction ir)
+{
+	u32 fcr31 = ctx->fcr31;
+	u32 value;
+	u32 mask;
+
+	if (MIPSInst_RT(ir) == 0)
+		value = 0;
+	else
+		value = xcp->regs[MIPSInst_RT(ir)];
+
+	switch (MIPSInst_RD(ir)) {
+	case FPCREG_CSR:
+		pr_debug("%p gpr[%d]->csr=%08x\n",
+			 (void *)xcp->cp0_epc, MIPSInst_RT(ir), value);
+
+		/* Preserve read-only bits.  */
+		mask = boot_cpu_data.fpu_msk31;
+		fcr31 = (value & ~mask) | (fcr31 & mask);
+		break;
+
+	case FPCREG_FENR:
+		if (!cpu_has_mips_r)
+			break;
+		pr_debug("%p gpr[%d]->enr=%08x\n",
+			 (void *)xcp->cp0_epc, MIPSInst_RT(ir), value);
+		fcr31 &= ~(FPU_CSR_FS | FPU_CSR_ALL_E | FPU_CSR_RM);
+		fcr31 |= (value << (FPU_CSR_FS_S - MIPS_FENR_FS_S)) &
+			 FPU_CSR_FS;
+		fcr31 |= value & (FPU_CSR_ALL_E | FPU_CSR_RM);
+		break;
+
+	case FPCREG_FEXR:
+		if (!cpu_has_mips_r)
+			break;
+		pr_debug("%p gpr[%d]->exr=%08x\n",
+			 (void *)xcp->cp0_epc, MIPSInst_RT(ir), value);
+		fcr31 &= ~(FPU_CSR_ALL_X | FPU_CSR_ALL_S);
+		fcr31 |= value & (FPU_CSR_ALL_X | FPU_CSR_ALL_S);
+		break;
+
+	case FPCREG_FCCR:
+		if (!cpu_has_mips_r)
+			break;
+		pr_debug("%p gpr[%d]->ccr=%08x\n",
+			 (void *)xcp->cp0_epc, MIPSInst_RT(ir), value);
+		fcr31 &= ~(FPU_CSR_CONDX | FPU_CSR_COND);
+		fcr31 |= (value << (FPU_CSR_COND_S - MIPS_FCCR_COND0_S)) &
+			 FPU_CSR_COND;
+		fcr31 |= (value << (FPU_CSR_COND1_S - MIPS_FCCR_COND1_S)) &
+			 FPU_CSR_CONDX;
+		break;
+
+	default:
+		break;
+	}
+
+	ctx->fcr31 = fcr31;
+}
+
+/*
+ * Emulate the single floating point instruction pointed at by EPC.
+ * Two instructions if the instruction is in a branch delay slot.
+ */
+
+static int cop1Emulate(struct pt_regs *xcp, struct mips_fpu_struct *ctx,
+		struct mm_decoded_insn dec_insn, void __user **fault_addr)
+{
+	unsigned long contpc = xcp->cp0_epc + dec_insn.pc_inc;
+	unsigned int cond, cbit, bit0;
+	mips_instruction ir;
+	int likely, pc_inc;
+	union fpureg *fpr;
+	u32 __user *wva;
+	u64 __user *dva;
+	u32 wval;
+	u64 dval;
+	int sig;
+
+	/*
+	 * These are giving gcc a gentle hint about what to expect in
+	 * dec_inst in order to do better optimization.
+	 */
+	if (!cpu_has_mmips && dec_insn.micro_mips_mode)
+		unreachable();
+
+	/* XXX NEC Vr54xx bug workaround */
+	if (delay_slot(xcp)) {
+		if (dec_insn.micro_mips_mode) {
+			if (!mm_isBranchInstr(xcp, dec_insn, &contpc))
+				clear_delay_slot(xcp);
+		} else {
+			if (!isBranchInstr(xcp, dec_insn, &contpc))
+				clear_delay_slot(xcp);
+		}
+	}
+
+	if (delay_slot(xcp)) {
+		/*
+		 * The instruction to be emulated is in a branch delay slot
+		 * which means that we have to	emulate the branch instruction
+		 * BEFORE we do the cop1 instruction.
+		 *
+		 * This branch could be a COP1 branch, but in that case we
+		 * would have had a trap for that instruction, and would not
+		 * come through this route.
+		 *
+		 * Linux MIPS branch emulator operates on context, updating the
+		 * cp0_epc.
+		 */
+		ir = dec_insn.next_insn;  /* process delay slot instr */
+		pc_inc = dec_insn.next_pc_inc;
+	} else {
+		ir = dec_insn.insn;       /* process current instr */
+		pc_inc = dec_insn.pc_inc;
+	}
+
+	/*
+	 * Since microMIPS FPU instructios are a subset of MIPS32 FPU
+	 * instructions, we want to convert microMIPS FPU instructions
+	 * into MIPS32 instructions so that we could reuse all of the
+	 * FPU emulation code.
+	 *
+	 * NOTE: We cannot do this for branch instructions since they
+	 *       are not a subset. Example: Cannot emulate a 16-bit
+	 *       aligned target address with a MIPS32 instruction.
+	 */
+	if (dec_insn.micro_mips_mode) {
+		/*
+		 * If next instruction is a 16-bit instruction, then
+		 * it cannot be a FPU instruction. This could happen
+		 * since we can be called for non-FPU instructions.
+		 */
+		if ((pc_inc == 2) ||
+			(microMIPS32_to_MIPS32((union mips_instruction *)&ir)
+			 == SIGILL))
+			return SIGILL;
+	}
+
+emul:
+	perf_sw_event(PERF_COUNT_SW_EMULATION_FAULTS, 1, xcp, 0);
+	MIPS_FPU_EMU_INC_STATS(emulated);
+	switch (MIPSInst_OPCODE(ir)) {
+	case ldc1_op:
+		dva = (u64 __user *) (xcp->regs[MIPSInst_RS(ir)] +
+				     MIPSInst_SIMM(ir));
+		MIPS_FPU_EMU_INC_STATS(loads);
+
+		if (!access_ok(dva, sizeof(u64))) {
+			MIPS_FPU_EMU_INC_STATS(errors);
+			*fault_addr = dva;
+			return SIGBUS;
+		}
+		if (__get_user(dval, dva)) {
+			MIPS_FPU_EMU_INC_STATS(errors);
+			*fault_addr = dva;
+			return SIGSEGV;
+		}
+		DITOREG(dval, MIPSInst_RT(ir));
+		break;
+
+	case sdc1_op:
+		dva = (u64 __user *) (xcp->regs[MIPSInst_RS(ir)] +
+				      MIPSInst_SIMM(ir));
+		MIPS_FPU_EMU_INC_STATS(stores);
+		DIFROMREG(dval, MIPSInst_RT(ir));
+		if (!access_ok(dva, sizeof(u64))) {
+			MIPS_FPU_EMU_INC_STATS(errors);
+			*fault_addr = dva;
+			return SIGBUS;
+		}
+		if (__put_user(dval, dva)) {
+			MIPS_FPU_EMU_INC_STATS(errors);
+			*fault_addr = dva;
+			return SIGSEGV;
+		}
+		break;
+
+	case lwc1_op:
+		wva = (u32 __user *) (xcp->regs[MIPSInst_RS(ir)] +
+				      MIPSInst_SIMM(ir));
+		MIPS_FPU_EMU_INC_STATS(loads);
+		if (!access_ok(wva, sizeof(u32))) {
+			MIPS_FPU_EMU_INC_STATS(errors);
+			*fault_addr = wva;
+			return SIGBUS;
+		}
+		if (__get_user(wval, wva)) {
+			MIPS_FPU_EMU_INC_STATS(errors);
+			*fault_addr = wva;
+			return SIGSEGV;
+		}
+		SITOREG(wval, MIPSInst_RT(ir));
+		break;
+
+	case swc1_op:
+		wva = (u32 __user *) (xcp->regs[MIPSInst_RS(ir)] +
+				      MIPSInst_SIMM(ir));
+		MIPS_FPU_EMU_INC_STATS(stores);
+		SIFROMREG(wval, MIPSInst_RT(ir));
+		if (!access_ok(wva, sizeof(u32))) {
+			MIPS_FPU_EMU_INC_STATS(errors);
+			*fault_addr = wva;
+			return SIGBUS;
+		}
+		if (__put_user(wval, wva)) {
+			MIPS_FPU_EMU_INC_STATS(errors);
+			*fault_addr = wva;
+			return SIGSEGV;
+		}
+		break;
+
+	case cop1_op:
+		switch (MIPSInst_RS(ir)) {
+		case dmfc_op:
+			if (!cpu_has_mips_3_4_5 && !cpu_has_mips64)
+				return SIGILL;
+
+			/* copregister fs -> gpr[rt] */
+			if (MIPSInst_RT(ir) != 0) {
+				DIFROMREG(xcp->regs[MIPSInst_RT(ir)],
+					MIPSInst_RD(ir));
+			}
+			break;
+
+		case dmtc_op:
+			if (!cpu_has_mips_3_4_5 && !cpu_has_mips64)
+				return SIGILL;
+
+			/* copregister fs <- rt */
+			DITOREG(xcp->regs[MIPSInst_RT(ir)], MIPSInst_RD(ir));
+			break;
+
+		case mfhc_op:
+			if (!cpu_has_mips_r2_r6)
+				return SIGILL;
+
+			/* copregister rd -> gpr[rt] */
+			if (MIPSInst_RT(ir) != 0) {
+				SIFROMHREG(xcp->regs[MIPSInst_RT(ir)],
+					MIPSInst_RD(ir));
+			}
+			break;
+
+		case mthc_op:
+			if (!cpu_has_mips_r2_r6)
+				return SIGILL;
+
+			/* copregister rd <- gpr[rt] */
+			SITOHREG(xcp->regs[MIPSInst_RT(ir)], MIPSInst_RD(ir));
+			break;
+
+		case mfc_op:
+			/* copregister rd -> gpr[rt] */
+			if (MIPSInst_RT(ir) != 0) {
+				SIFROMREG(xcp->regs[MIPSInst_RT(ir)],
+					MIPSInst_RD(ir));
+			}
+			break;
+
+		case mtc_op:
+			/* copregister rd <- rt */
+			SITOREG(xcp->regs[MIPSInst_RT(ir)], MIPSInst_RD(ir));
+			break;
+
+		case cfc_op:
+			/* cop control register rd -> gpr[rt] */
+			cop1_cfc(xcp, ctx, ir);
+			break;
+
+		case ctc_op:
+			/* copregister rd <- rt */
+			cop1_ctc(xcp, ctx, ir);
+			if ((ctx->fcr31 >> 5) & ctx->fcr31 & FPU_CSR_ALL_E) {
+				return SIGFPE;
+			}
+			break;
+
+		case bc1eqz_op:
+		case bc1nez_op:
+			if (!cpu_has_mips_r6 || delay_slot(xcp))
+				return SIGILL;
+
+			likely = 0;
+			cond = 0;
+			fpr = &current->thread.fpu.fpr[MIPSInst_RT(ir)];
+			bit0 = get_fpr32(fpr, 0) & 0x1;
+			switch (MIPSInst_RS(ir)) {
+			case bc1eqz_op:
+				MIPS_FPU_EMU_INC_STATS(bc1eqz);
+				cond = bit0 == 0;
+				break;
+			case bc1nez_op:
+				MIPS_FPU_EMU_INC_STATS(bc1nez);
+				cond = bit0 != 0;
+				break;
+			}
+			goto branch_common;
+
+		case bc_op:
+			if (delay_slot(xcp))
+				return SIGILL;
+
+			if (cpu_has_mips_4_5_r)
+				cbit = fpucondbit[MIPSInst_RT(ir) >> 2];
+			else
+				cbit = FPU_CSR_COND;
+			cond = ctx->fcr31 & cbit;
+
+			likely = 0;
+			switch (MIPSInst_RT(ir) & 3) {
+			case bcfl_op:
+				if (cpu_has_mips_2_3_4_5_r)
+					likely = 1;
+				fallthrough;
+			case bcf_op:
+				cond = !cond;
+				break;
+			case bctl_op:
+				if (cpu_has_mips_2_3_4_5_r)
+					likely = 1;
+				fallthrough;
+			case bct_op:
+				break;
+			}
+branch_common:
+			MIPS_FPU_EMU_INC_STATS(branches);
+			set_delay_slot(xcp);
+			if (cond) {
+				/*
+				 * Branch taken: emulate dslot instruction
+				 */
+				unsigned long bcpc;
+
+				/*
+				 * Remember EPC at the branch to point back
+				 * at so that any delay-slot instruction
+				 * signal is not silently ignored.
+				 */
+				bcpc = xcp->cp0_epc;
+				xcp->cp0_epc += dec_insn.pc_inc;
+
+				contpc = MIPSInst_SIMM(ir);
+				ir = dec_insn.next_insn;
+				if (dec_insn.micro_mips_mode) {
+					contpc = (xcp->cp0_epc + (contpc << 1));
+
+					/* If 16-bit instruction, not FPU. */
+					if ((dec_insn.next_pc_inc == 2) ||
+						(microMIPS32_to_MIPS32((union mips_instruction *)&ir) == SIGILL)) {
+
+						/*
+						 * Since this instruction will
+						 * be put on the stack with
+						 * 32-bit words, get around
+						 * this problem by putting a
+						 * NOP16 as the second one.
+						 */
+						if (dec_insn.next_pc_inc == 2)
+							ir = (ir & (~0xffff)) | MM_NOP16;
+
+						/*
+						 * Single step the non-CP1
+						 * instruction in the dslot.
+						 */
+						sig = mips_dsemul(xcp, ir,
+								  bcpc, contpc);
+						if (sig < 0)
+							break;
+						if (sig)
+							xcp->cp0_epc = bcpc;
+						/*
+						 * SIGILL forces out of
+						 * the emulation loop.
+						 */
+						return sig ? sig : SIGILL;
+					}
+				} else
+					contpc = (xcp->cp0_epc + (contpc << 2));
+
+				switch (MIPSInst_OPCODE(ir)) {
+				case lwc1_op:
+				case swc1_op:
+					goto emul;
+
+				case ldc1_op:
+				case sdc1_op:
+					if (cpu_has_mips_2_3_4_5_r)
+						goto emul;
+
+					goto bc_sigill;
+
+				case cop1_op:
+					goto emul;
+
+				case cop1x_op:
+					if (cpu_has_mips_4_5_64_r2_r6)
+						/* its one of ours */
+						goto emul;
+
+					goto bc_sigill;
+
+				case spec_op:
+					switch (MIPSInst_FUNC(ir)) {
+					case movc_op:
+						if (cpu_has_mips_4_5_r)
+							goto emul;
+
+						goto bc_sigill;
+					}
+					break;
+
+				bc_sigill:
+					xcp->cp0_epc = bcpc;
+					return SIGILL;
+				}
+
+				/*
+				 * Single step the non-cp1
+				 * instruction in the dslot
+				 */
+				sig = mips_dsemul(xcp, ir, bcpc, contpc);
+				if (sig < 0)
+					break;
+				if (sig)
+					xcp->cp0_epc = bcpc;
+				/* SIGILL forces out of the emulation loop.  */
+				return sig ? sig : SIGILL;
+			} else if (likely) {	/* branch not taken */
+				/*
+				 * branch likely nullifies
+				 * dslot if not taken
+				 */
+				xcp->cp0_epc += dec_insn.pc_inc;
+				contpc += dec_insn.pc_inc;
+				/*
+				 * else continue & execute
+				 * dslot as normal insn
+				 */
+			}
+			break;
+
+		default:
+			if (!(MIPSInst_RS(ir) & 0x10))
+				return SIGILL;
+
+			/* a real fpu computation instruction */
+			sig = fpu_emu(xcp, ctx, ir);
+			if (sig)
+				return sig;
+		}
+		break;
+
+	case cop1x_op:
+		if (!cpu_has_mips_4_5_64_r2_r6)
+			return SIGILL;
+
+		sig = fpux_emu(xcp, ctx, ir, fault_addr);
+		if (sig)
+			return sig;
+		break;
+
+	case spec_op:
+		if (!cpu_has_mips_4_5_r)
+			return SIGILL;
+
+		if (MIPSInst_FUNC(ir) != movc_op)
+			return SIGILL;
+		cond = fpucondbit[MIPSInst_RT(ir) >> 2];
+		if (((ctx->fcr31 & cond) != 0) == ((MIPSInst_RT(ir) & 1) != 0))
+			xcp->regs[MIPSInst_RD(ir)] =
+				xcp->regs[MIPSInst_RS(ir)];
+		break;
+	default:
+		return SIGILL;
+	}
+
+	/* we did it !! */
+	xcp->cp0_epc = contpc;
+	clear_delay_slot(xcp);
+
+	return 0;
+}
+
+/*
+ * Conversion table from MIPS compare ops 48-63
+ * cond = ieee754dp_cmp(x,y,IEEE754_UN,sig);
+ */
+static const unsigned char cmptab[8] = {
+	0,			/* cmp_0 (sig) cmp_sf */
+	IEEE754_CUN,		/* cmp_un (sig) cmp_ngle */
+	IEEE754_CEQ,		/* cmp_eq (sig) cmp_seq */
+	IEEE754_CEQ | IEEE754_CUN,	/* cmp_ueq (sig) cmp_ngl  */
+	IEEE754_CLT,		/* cmp_olt (sig) cmp_lt */
+	IEEE754_CLT | IEEE754_CUN,	/* cmp_ult (sig) cmp_nge */
+	IEEE754_CLT | IEEE754_CEQ,	/* cmp_ole (sig) cmp_le */
+	IEEE754_CLT | IEEE754_CEQ | IEEE754_CUN,	/* cmp_ule (sig) cmp_ngt */
+};
+
+static const unsigned char negative_cmptab[8] = {
+	0, /* Reserved */
+	IEEE754_CLT | IEEE754_CGT | IEEE754_CEQ,
+	IEEE754_CLT | IEEE754_CGT | IEEE754_CUN,
+	IEEE754_CLT | IEEE754_CGT,
+	/* Reserved */
+};
+
+
+/*
+ * Additional MIPS4 instructions
+ */
+
+#define DEF3OP(name, p, f1, f2, f3)					\
+static union ieee754##p fpemu_##p##_##name(union ieee754##p r,		\
+	union ieee754##p s, union ieee754##p t)				\
+{									\
+	struct _ieee754_csr ieee754_csr_save;				\
+	s = f1(s, t);							\
+	ieee754_csr_save = ieee754_csr;					\
+	s = f2(s, r);							\
+	ieee754_csr_save.cx |= ieee754_csr.cx;				\
+	ieee754_csr_save.sx |= ieee754_csr.sx;				\
+	s = f3(s);							\
+	ieee754_csr.cx |= ieee754_csr_save.cx;				\
+	ieee754_csr.sx |= ieee754_csr_save.sx;				\
+	return s;							\
+}
+
+static union ieee754dp fpemu_dp_recip(union ieee754dp d)
+{
+	return ieee754dp_div(ieee754dp_one(0), d);
+}
+
+static union ieee754dp fpemu_dp_rsqrt(union ieee754dp d)
+{
+	return ieee754dp_div(ieee754dp_one(0), ieee754dp_sqrt(d));
+}
+
+static union ieee754sp fpemu_sp_recip(union ieee754sp s)
+{
+	return ieee754sp_div(ieee754sp_one(0), s);
+}
+
+static union ieee754sp fpemu_sp_rsqrt(union ieee754sp s)
+{
+	return ieee754sp_div(ieee754sp_one(0), ieee754sp_sqrt(s));
+}
+
+DEF3OP(madd, sp, ieee754sp_mul, ieee754sp_add, );
+DEF3OP(msub, sp, ieee754sp_mul, ieee754sp_sub, );
+DEF3OP(nmadd, sp, ieee754sp_mul, ieee754sp_add, ieee754sp_neg);
+DEF3OP(nmsub, sp, ieee754sp_mul, ieee754sp_sub, ieee754sp_neg);
+DEF3OP(madd, dp, ieee754dp_mul, ieee754dp_add, );
+DEF3OP(msub, dp, ieee754dp_mul, ieee754dp_sub, );
+DEF3OP(nmadd, dp, ieee754dp_mul, ieee754dp_add, ieee754dp_neg);
+DEF3OP(nmsub, dp, ieee754dp_mul, ieee754dp_sub, ieee754dp_neg);
+
+static int fpux_emu(struct pt_regs *xcp, struct mips_fpu_struct *ctx,
+	mips_instruction ir, void __user **fault_addr)
+{
+	unsigned int rcsr = 0;	/* resulting csr */
+
+	MIPS_FPU_EMU_INC_STATS(cp1xops);
+
+	switch (MIPSInst_FMA_FFMT(ir)) {
+	case s_fmt:{		/* 0 */
+
+		union ieee754sp(*handler) (union ieee754sp, union ieee754sp, union ieee754sp);
+		union ieee754sp fd, fr, fs, ft;
+		u32 __user *va;
+		u32 val;
+
+		switch (MIPSInst_FUNC(ir)) {
+		case lwxc1_op:
+			va = (void __user *) (xcp->regs[MIPSInst_FR(ir)] +
+				xcp->regs[MIPSInst_FT(ir)]);
+
+			MIPS_FPU_EMU_INC_STATS(loads);
+			if (!access_ok(va, sizeof(u32))) {
+				MIPS_FPU_EMU_INC_STATS(errors);
+				*fault_addr = va;
+				return SIGBUS;
+			}
+			if (__get_user(val, va)) {
+				MIPS_FPU_EMU_INC_STATS(errors);
+				*fault_addr = va;
+				return SIGSEGV;
+			}
+			SITOREG(val, MIPSInst_FD(ir));
+			break;
+
+		case swxc1_op:
+			va = (void __user *) (xcp->regs[MIPSInst_FR(ir)] +
+				xcp->regs[MIPSInst_FT(ir)]);
+
+			MIPS_FPU_EMU_INC_STATS(stores);
+
+			SIFROMREG(val, MIPSInst_FS(ir));
+			if (!access_ok(va, sizeof(u32))) {
+				MIPS_FPU_EMU_INC_STATS(errors);
+				*fault_addr = va;
+				return SIGBUS;
+			}
+			if (put_user(val, va)) {
+				MIPS_FPU_EMU_INC_STATS(errors);
+				*fault_addr = va;
+				return SIGSEGV;
+			}
+			break;
+
+		case madd_s_op:
+			if (cpu_has_mac2008_only)
+				handler = ieee754sp_madd;
+			else
+				handler = fpemu_sp_madd;
+			goto scoptop;
+		case msub_s_op:
+			if (cpu_has_mac2008_only)
+				handler = ieee754sp_msub;
+			else
+				handler = fpemu_sp_msub;
+			goto scoptop;
+		case nmadd_s_op:
+			if (cpu_has_mac2008_only)
+				handler = ieee754sp_nmadd;
+			else
+				handler = fpemu_sp_nmadd;
+			goto scoptop;
+		case nmsub_s_op:
+			if (cpu_has_mac2008_only)
+				handler = ieee754sp_nmsub;
+			else
+				handler = fpemu_sp_nmsub;
+			goto scoptop;
+
+		      scoptop:
+			SPFROMREG(fr, MIPSInst_FR(ir));
+			SPFROMREG(fs, MIPSInst_FS(ir));
+			SPFROMREG(ft, MIPSInst_FT(ir));
+			fd = (*handler) (fr, fs, ft);
+			SPTOREG(fd, MIPSInst_FD(ir));
+
+		      copcsr:
+			if (ieee754_cxtest(IEEE754_INEXACT)) {
+				MIPS_FPU_EMU_INC_STATS(ieee754_inexact);
+				rcsr |= FPU_CSR_INE_X | FPU_CSR_INE_S;
+			}
+			if (ieee754_cxtest(IEEE754_UNDERFLOW)) {
+				MIPS_FPU_EMU_INC_STATS(ieee754_underflow);
+				rcsr |= FPU_CSR_UDF_X | FPU_CSR_UDF_S;
+			}
+			if (ieee754_cxtest(IEEE754_OVERFLOW)) {
+				MIPS_FPU_EMU_INC_STATS(ieee754_overflow);
+				rcsr |= FPU_CSR_OVF_X | FPU_CSR_OVF_S;
+			}
+			if (ieee754_cxtest(IEEE754_INVALID_OPERATION)) {
+				MIPS_FPU_EMU_INC_STATS(ieee754_invalidop);
+				rcsr |= FPU_CSR_INV_X | FPU_CSR_INV_S;
+			}
+
+			ctx->fcr31 = (ctx->fcr31 & ~FPU_CSR_ALL_X) | rcsr;
+			if ((ctx->fcr31 >> 5) & ctx->fcr31 & FPU_CSR_ALL_E) {
+				/*printk ("SIGFPE: FPU csr = %08x\n",
+				   ctx->fcr31); */
+				return SIGFPE;
+			}
+
+			break;
+
+		default:
+			return SIGILL;
+		}
+		break;
+	}
+
+	case d_fmt:{		/* 1 */
+		union ieee754dp(*handler) (union ieee754dp, union ieee754dp, union ieee754dp);
+		union ieee754dp fd, fr, fs, ft;
+		u64 __user *va;
+		u64 val;
+
+		switch (MIPSInst_FUNC(ir)) {
+		case ldxc1_op:
+			va = (void __user *) (xcp->regs[MIPSInst_FR(ir)] +
+				xcp->regs[MIPSInst_FT(ir)]);
+
+			MIPS_FPU_EMU_INC_STATS(loads);
+			if (!access_ok(va, sizeof(u64))) {
+				MIPS_FPU_EMU_INC_STATS(errors);
+				*fault_addr = va;
+				return SIGBUS;
+			}
+			if (__get_user(val, va)) {
+				MIPS_FPU_EMU_INC_STATS(errors);
+				*fault_addr = va;
+				return SIGSEGV;
+			}
+			DITOREG(val, MIPSInst_FD(ir));
+			break;
+
+		case sdxc1_op:
+			va = (void __user *) (xcp->regs[MIPSInst_FR(ir)] +
+				xcp->regs[MIPSInst_FT(ir)]);
+
+			MIPS_FPU_EMU_INC_STATS(stores);
+			DIFROMREG(val, MIPSInst_FS(ir));
+			if (!access_ok(va, sizeof(u64))) {
+				MIPS_FPU_EMU_INC_STATS(errors);
+				*fault_addr = va;
+				return SIGBUS;
+			}
+			if (__put_user(val, va)) {
+				MIPS_FPU_EMU_INC_STATS(errors);
+				*fault_addr = va;
+				return SIGSEGV;
+			}
+			break;
+
+		case madd_d_op:
+			if (cpu_has_mac2008_only)
+				handler = ieee754dp_madd;
+			else
+				handler = fpemu_dp_madd;
+			goto dcoptop;
+		case msub_d_op:
+			if (cpu_has_mac2008_only)
+				handler = ieee754dp_msub;
+			else
+				handler = fpemu_dp_msub;
+			goto dcoptop;
+		case nmadd_d_op:
+			if (cpu_has_mac2008_only)
+				handler = ieee754dp_nmadd;
+			else
+				handler = fpemu_dp_nmadd;
+			goto dcoptop;
+		case nmsub_d_op:
+			if (cpu_has_mac2008_only)
+				handler = ieee754dp_nmsub;
+			else
+			handler = fpemu_dp_nmsub;
+			goto dcoptop;
+
+		      dcoptop:
+			DPFROMREG(fr, MIPSInst_FR(ir));
+			DPFROMREG(fs, MIPSInst_FS(ir));
+			DPFROMREG(ft, MIPSInst_FT(ir));
+			fd = (*handler) (fr, fs, ft);
+			DPTOREG(fd, MIPSInst_FD(ir));
+			goto copcsr;
+
+		default:
+			return SIGILL;
+		}
+		break;
+	}
+
+	case 0x3:
+		if (MIPSInst_FUNC(ir) != pfetch_op)
+			return SIGILL;
+
+		/* ignore prefx operation */
+		break;
+
+	default:
+		return SIGILL;
+	}
+
+	return 0;
+}
+
+
+
+/*
+ * Emulate a single COP1 arithmetic instruction.
+ */
+static int fpu_emu(struct pt_regs *xcp, struct mips_fpu_struct *ctx,
+	mips_instruction ir)
+{
+	int rfmt;		/* resulting format */
+	unsigned int rcsr = 0;	/* resulting csr */
+	unsigned int oldrm;
+	unsigned int cbit;
+	unsigned int cond;
+	union {
+		union ieee754dp d;
+		union ieee754sp s;
+		int w;
+		s64 l;
+	} rv;			/* resulting value */
+	u64 bits;
+
+	MIPS_FPU_EMU_INC_STATS(cp1ops);
+	switch (rfmt = (MIPSInst_FFMT(ir) & 0xf)) {
+	case s_fmt: {		/* 0 */
+		union {
+			union ieee754sp(*b) (union ieee754sp, union ieee754sp);
+			union ieee754sp(*u) (union ieee754sp);
+		} handler;
+		union ieee754sp fd, fs, ft;
+
+		switch (MIPSInst_FUNC(ir)) {
+			/* binary ops */
+		case fadd_op:
+			MIPS_FPU_EMU_INC_STATS(add_s);
+			handler.b = ieee754sp_add;
+			goto scopbop;
+		case fsub_op:
+			MIPS_FPU_EMU_INC_STATS(sub_s);
+			handler.b = ieee754sp_sub;
+			goto scopbop;
+		case fmul_op:
+			MIPS_FPU_EMU_INC_STATS(mul_s);
+			handler.b = ieee754sp_mul;
+			goto scopbop;
+		case fdiv_op:
+			MIPS_FPU_EMU_INC_STATS(div_s);
+			handler.b = ieee754sp_div;
+			goto scopbop;
+
+			/* unary  ops */
+		case fsqrt_op:
+			if (!cpu_has_mips_2_3_4_5_r)
+				return SIGILL;
+
+			MIPS_FPU_EMU_INC_STATS(sqrt_s);
+			handler.u = ieee754sp_sqrt;
+			goto scopuop;
+
+		/*
+		 * Note that on some MIPS IV implementations such as the
+		 * R5000 and R8000 the FSQRT and FRECIP instructions do not
+		 * achieve full IEEE-754 accuracy - however this emulator does.
+		 */
+		case frsqrt_op:
+			if (!cpu_has_mips_4_5_64_r2_r6)
+				return SIGILL;
+
+			MIPS_FPU_EMU_INC_STATS(rsqrt_s);
+			handler.u = fpemu_sp_rsqrt;
+			goto scopuop;
+
+		case frecip_op:
+			if (!cpu_has_mips_4_5_64_r2_r6)
+				return SIGILL;
+
+			MIPS_FPU_EMU_INC_STATS(recip_s);
+			handler.u = fpemu_sp_recip;
+			goto scopuop;
+
+		case fmovc_op:
+			if (!cpu_has_mips_4_5_r)
+				return SIGILL;
+
+			cond = fpucondbit[MIPSInst_FT(ir) >> 2];
+			if (((ctx->fcr31 & cond) != 0) !=
+				((MIPSInst_FT(ir) & 1) != 0))
+				return 0;
+			SPFROMREG(rv.s, MIPSInst_FS(ir));
+			break;
+
+		case fmovz_op:
+			if (!cpu_has_mips_4_5_r)
+				return SIGILL;
+
+			if (xcp->regs[MIPSInst_FT(ir)] != 0)
+				return 0;
+			SPFROMREG(rv.s, MIPSInst_FS(ir));
+			break;
+
+		case fmovn_op:
+			if (!cpu_has_mips_4_5_r)
+				return SIGILL;
+
+			if (xcp->regs[MIPSInst_FT(ir)] == 0)
+				return 0;
+			SPFROMREG(rv.s, MIPSInst_FS(ir));
+			break;
+
+		case fseleqz_op:
+			if (!cpu_has_mips_r6)
+				return SIGILL;
+
+			MIPS_FPU_EMU_INC_STATS(seleqz_s);
+			SPFROMREG(rv.s, MIPSInst_FT(ir));
+			if (rv.w & 0x1)
+				rv.w = 0;
+			else
+				SPFROMREG(rv.s, MIPSInst_FS(ir));
+			break;
+
+		case fselnez_op:
+			if (!cpu_has_mips_r6)
+				return SIGILL;
+
+			MIPS_FPU_EMU_INC_STATS(selnez_s);
+			SPFROMREG(rv.s, MIPSInst_FT(ir));
+			if (rv.w & 0x1)
+				SPFROMREG(rv.s, MIPSInst_FS(ir));
+			else
+				rv.w = 0;
+			break;
+
+		case fmaddf_op: {
+			union ieee754sp ft, fs, fd;
+
+			if (!cpu_has_mips_r6)
+				return SIGILL;
+
+			MIPS_FPU_EMU_INC_STATS(maddf_s);
+			SPFROMREG(ft, MIPSInst_FT(ir));
+			SPFROMREG(fs, MIPSInst_FS(ir));
+			SPFROMREG(fd, MIPSInst_FD(ir));
+			rv.s = ieee754sp_maddf(fd, fs, ft);
+			goto copcsr;
+		}
+
+		case fmsubf_op: {
+			union ieee754sp ft, fs, fd;
+
+			if (!cpu_has_mips_r6)
+				return SIGILL;
+
+			MIPS_FPU_EMU_INC_STATS(msubf_s);
+			SPFROMREG(ft, MIPSInst_FT(ir));
+			SPFROMREG(fs, MIPSInst_FS(ir));
+			SPFROMREG(fd, MIPSInst_FD(ir));
+			rv.s = ieee754sp_msubf(fd, fs, ft);
+			goto copcsr;
+		}
+
+		case frint_op: {
+			union ieee754sp fs;
+
+			if (!cpu_has_mips_r6)
+				return SIGILL;
+
+			MIPS_FPU_EMU_INC_STATS(rint_s);
+			SPFROMREG(fs, MIPSInst_FS(ir));
+			rv.s = ieee754sp_rint(fs);
+			goto copcsr;
+		}
+
+		case fclass_op: {
+			union ieee754sp fs;
+
+			if (!cpu_has_mips_r6)
+				return SIGILL;
+
+			MIPS_FPU_EMU_INC_STATS(class_s);
+			SPFROMREG(fs, MIPSInst_FS(ir));
+			rv.w = ieee754sp_2008class(fs);
+			rfmt = w_fmt;
+			goto copcsr;
+		}
+
+		case fmin_op: {
+			union ieee754sp fs, ft;
+
+			if (!cpu_has_mips_r6)
+				return SIGILL;
+
+			MIPS_FPU_EMU_INC_STATS(min_s);
+			SPFROMREG(ft, MIPSInst_FT(ir));
+			SPFROMREG(fs, MIPSInst_FS(ir));
+			rv.s = ieee754sp_fmin(fs, ft);
+			goto copcsr;
+		}
+
+		case fmina_op: {
+			union ieee754sp fs, ft;
+
+			if (!cpu_has_mips_r6)
+				return SIGILL;
+
+			MIPS_FPU_EMU_INC_STATS(mina_s);
+			SPFROMREG(ft, MIPSInst_FT(ir));
+			SPFROMREG(fs, MIPSInst_FS(ir));
+			rv.s = ieee754sp_fmina(fs, ft);
+			goto copcsr;
+		}
+
+		case fmax_op: {
+			union ieee754sp fs, ft;
+
+			if (!cpu_has_mips_r6)
+				return SIGILL;
+
+			MIPS_FPU_EMU_INC_STATS(max_s);
+			SPFROMREG(ft, MIPSInst_FT(ir));
+			SPFROMREG(fs, MIPSInst_FS(ir));
+			rv.s = ieee754sp_fmax(fs, ft);
+			goto copcsr;
+		}
+
+		case fmaxa_op: {
+			union ieee754sp fs, ft;
+
+			if (!cpu_has_mips_r6)
+				return SIGILL;
+
+			MIPS_FPU_EMU_INC_STATS(maxa_s);
+			SPFROMREG(ft, MIPSInst_FT(ir));
+			SPFROMREG(fs, MIPSInst_FS(ir));
+			rv.s = ieee754sp_fmaxa(fs, ft);
+			goto copcsr;
+		}
+
+		case fabs_op:
+			MIPS_FPU_EMU_INC_STATS(abs_s);
+			handler.u = ieee754sp_abs;
+			goto scopuop;
+
+		case fneg_op:
+			MIPS_FPU_EMU_INC_STATS(neg_s);
+			handler.u = ieee754sp_neg;
+			goto scopuop;
+
+		case fmov_op:
+			/* an easy one */
+			MIPS_FPU_EMU_INC_STATS(mov_s);
+			SPFROMREG(rv.s, MIPSInst_FS(ir));
+			goto copcsr;
+
+			/* binary op on handler */
+scopbop:
+			SPFROMREG(fs, MIPSInst_FS(ir));
+			SPFROMREG(ft, MIPSInst_FT(ir));
+
+			rv.s = (*handler.b) (fs, ft);
+			goto copcsr;
+scopuop:
+			SPFROMREG(fs, MIPSInst_FS(ir));
+			rv.s = (*handler.u) (fs);
+			goto copcsr;
+copcsr:
+			if (ieee754_cxtest(IEEE754_INEXACT)) {
+				MIPS_FPU_EMU_INC_STATS(ieee754_inexact);
+				rcsr |= FPU_CSR_INE_X | FPU_CSR_INE_S;
+			}
+			if (ieee754_cxtest(IEEE754_UNDERFLOW)) {
+				MIPS_FPU_EMU_INC_STATS(ieee754_underflow);
+				rcsr |= FPU_CSR_UDF_X | FPU_CSR_UDF_S;
+			}
+			if (ieee754_cxtest(IEEE754_OVERFLOW)) {
+				MIPS_FPU_EMU_INC_STATS(ieee754_overflow);
+				rcsr |= FPU_CSR_OVF_X | FPU_CSR_OVF_S;
+			}
+			if (ieee754_cxtest(IEEE754_ZERO_DIVIDE)) {
+				MIPS_FPU_EMU_INC_STATS(ieee754_zerodiv);
+				rcsr |= FPU_CSR_DIV_X | FPU_CSR_DIV_S;
+			}
+			if (ieee754_cxtest(IEEE754_INVALID_OPERATION)) {
+				MIPS_FPU_EMU_INC_STATS(ieee754_invalidop);
+				rcsr |= FPU_CSR_INV_X | FPU_CSR_INV_S;
+			}
+			break;
+
+			/* unary conv ops */
+		case fcvts_op:
+			return SIGILL;	/* not defined */
+
+		case fcvtd_op:
+			MIPS_FPU_EMU_INC_STATS(cvt_d_s);
+			SPFROMREG(fs, MIPSInst_FS(ir));
+			rv.d = ieee754dp_fsp(fs);
+			rfmt = d_fmt;
+			goto copcsr;
+
+		case fcvtw_op:
+			MIPS_FPU_EMU_INC_STATS(cvt_w_s);
+			SPFROMREG(fs, MIPSInst_FS(ir));
+			rv.w = ieee754sp_tint(fs);
+			rfmt = w_fmt;
+			goto copcsr;
+
+		case fround_op:
+		case ftrunc_op:
+		case fceil_op:
+		case ffloor_op:
+			if (!cpu_has_mips_2_3_4_5_r)
+				return SIGILL;
+
+			if (MIPSInst_FUNC(ir) == fceil_op)
+				MIPS_FPU_EMU_INC_STATS(ceil_w_s);
+			if (MIPSInst_FUNC(ir) == ffloor_op)
+				MIPS_FPU_EMU_INC_STATS(floor_w_s);
+			if (MIPSInst_FUNC(ir) == fround_op)
+				MIPS_FPU_EMU_INC_STATS(round_w_s);
+			if (MIPSInst_FUNC(ir) == ftrunc_op)
+				MIPS_FPU_EMU_INC_STATS(trunc_w_s);
+
+			oldrm = ieee754_csr.rm;
+			SPFROMREG(fs, MIPSInst_FS(ir));
+			ieee754_csr.rm = MIPSInst_FUNC(ir);
+			rv.w = ieee754sp_tint(fs);
+			ieee754_csr.rm = oldrm;
+			rfmt = w_fmt;
+			goto copcsr;
+
+		case fsel_op:
+			if (!cpu_has_mips_r6)
+				return SIGILL;
+
+			MIPS_FPU_EMU_INC_STATS(sel_s);
+			SPFROMREG(fd, MIPSInst_FD(ir));
+			if (fd.bits & 0x1)
+				SPFROMREG(rv.s, MIPSInst_FT(ir));
+			else
+				SPFROMREG(rv.s, MIPSInst_FS(ir));
+			break;
+
+		case fcvtl_op:
+			if (!cpu_has_mips_3_4_5_64_r2_r6)
+				return SIGILL;
+
+			MIPS_FPU_EMU_INC_STATS(cvt_l_s);
+			SPFROMREG(fs, MIPSInst_FS(ir));
+			rv.l = ieee754sp_tlong(fs);
+			rfmt = l_fmt;
+			goto copcsr;
+
+		case froundl_op:
+		case ftruncl_op:
+		case fceill_op:
+		case ffloorl_op:
+			if (!cpu_has_mips_3_4_5_64_r2_r6)
+				return SIGILL;
+
+			if (MIPSInst_FUNC(ir) == fceill_op)
+				MIPS_FPU_EMU_INC_STATS(ceil_l_s);
+			if (MIPSInst_FUNC(ir) == ffloorl_op)
+				MIPS_FPU_EMU_INC_STATS(floor_l_s);
+			if (MIPSInst_FUNC(ir) == froundl_op)
+				MIPS_FPU_EMU_INC_STATS(round_l_s);
+			if (MIPSInst_FUNC(ir) == ftruncl_op)
+				MIPS_FPU_EMU_INC_STATS(trunc_l_s);
+
+			oldrm = ieee754_csr.rm;
+			SPFROMREG(fs, MIPSInst_FS(ir));
+			ieee754_csr.rm = MIPSInst_FUNC(ir);
+			rv.l = ieee754sp_tlong(fs);
+			ieee754_csr.rm = oldrm;
+			rfmt = l_fmt;
+			goto copcsr;
+
+		default:
+			if (!NO_R6EMU && MIPSInst_FUNC(ir) >= fcmp_op) {
+				unsigned int cmpop;
+				union ieee754sp fs, ft;
+
+				cmpop = MIPSInst_FUNC(ir) - fcmp_op;
+				SPFROMREG(fs, MIPSInst_FS(ir));
+				SPFROMREG(ft, MIPSInst_FT(ir));
+				rv.w = ieee754sp_cmp(fs, ft,
+					cmptab[cmpop & 0x7], cmpop & 0x8);
+				rfmt = -1;
+				if ((cmpop & 0x8) && ieee754_cxtest
+					(IEEE754_INVALID_OPERATION))
+					rcsr = FPU_CSR_INV_X | FPU_CSR_INV_S;
+				else
+					goto copcsr;
+
+			} else
+				return SIGILL;
+			break;
+		}
+		break;
+	}
+
+	case d_fmt: {
+		union ieee754dp fd, fs, ft;
+		union {
+			union ieee754dp(*b) (union ieee754dp, union ieee754dp);
+			union ieee754dp(*u) (union ieee754dp);
+		} handler;
+
+		switch (MIPSInst_FUNC(ir)) {
+			/* binary ops */
+		case fadd_op:
+			MIPS_FPU_EMU_INC_STATS(add_d);
+			handler.b = ieee754dp_add;
+			goto dcopbop;
+		case fsub_op:
+			MIPS_FPU_EMU_INC_STATS(sub_d);
+			handler.b = ieee754dp_sub;
+			goto dcopbop;
+		case fmul_op:
+			MIPS_FPU_EMU_INC_STATS(mul_d);
+			handler.b = ieee754dp_mul;
+			goto dcopbop;
+		case fdiv_op:
+			MIPS_FPU_EMU_INC_STATS(div_d);
+			handler.b = ieee754dp_div;
+			goto dcopbop;
+
+			/* unary  ops */
+		case fsqrt_op:
+			if (!cpu_has_mips_2_3_4_5_r)
+				return SIGILL;
+
+			MIPS_FPU_EMU_INC_STATS(sqrt_d);
+			handler.u = ieee754dp_sqrt;
+			goto dcopuop;
+		/*
+		 * Note that on some MIPS IV implementations such as the
+		 * R5000 and R8000 the FSQRT and FRECIP instructions do not
+		 * achieve full IEEE-754 accuracy - however this emulator does.
+		 */
+		case frsqrt_op:
+			if (!cpu_has_mips_4_5_64_r2_r6)
+				return SIGILL;
+
+			MIPS_FPU_EMU_INC_STATS(rsqrt_d);
+			handler.u = fpemu_dp_rsqrt;
+			goto dcopuop;
+		case frecip_op:
+			if (!cpu_has_mips_4_5_64_r2_r6)
+				return SIGILL;
+
+			MIPS_FPU_EMU_INC_STATS(recip_d);
+			handler.u = fpemu_dp_recip;
+			goto dcopuop;
+		case fmovc_op:
+			if (!cpu_has_mips_4_5_r)
+				return SIGILL;
+
+			cond = fpucondbit[MIPSInst_FT(ir) >> 2];
+			if (((ctx->fcr31 & cond) != 0) !=
+				((MIPSInst_FT(ir) & 1) != 0))
+				return 0;
+			DPFROMREG(rv.d, MIPSInst_FS(ir));
+			break;
+		case fmovz_op:
+			if (!cpu_has_mips_4_5_r)
+				return SIGILL;
+
+			if (xcp->regs[MIPSInst_FT(ir)] != 0)
+				return 0;
+			DPFROMREG(rv.d, MIPSInst_FS(ir));
+			break;
+		case fmovn_op:
+			if (!cpu_has_mips_4_5_r)
+				return SIGILL;
+
+			if (xcp->regs[MIPSInst_FT(ir)] == 0)
+				return 0;
+			DPFROMREG(rv.d, MIPSInst_FS(ir));
+			break;
+
+		case fseleqz_op:
+			if (!cpu_has_mips_r6)
+				return SIGILL;
+
+			MIPS_FPU_EMU_INC_STATS(seleqz_d);
+			DPFROMREG(rv.d, MIPSInst_FT(ir));
+			if (rv.l & 0x1)
+				rv.l = 0;
+			else
+				DPFROMREG(rv.d, MIPSInst_FS(ir));
+			break;
+
+		case fselnez_op:
+			if (!cpu_has_mips_r6)
+				return SIGILL;
+
+			MIPS_FPU_EMU_INC_STATS(selnez_d);
+			DPFROMREG(rv.d, MIPSInst_FT(ir));
+			if (rv.l & 0x1)
+				DPFROMREG(rv.d, MIPSInst_FS(ir));
+			else
+				rv.l = 0;
+			break;
+
+		case fmaddf_op: {
+			union ieee754dp ft, fs, fd;
+
+			if (!cpu_has_mips_r6)
+				return SIGILL;
+
+			MIPS_FPU_EMU_INC_STATS(maddf_d);
+			DPFROMREG(ft, MIPSInst_FT(ir));
+			DPFROMREG(fs, MIPSInst_FS(ir));
+			DPFROMREG(fd, MIPSInst_FD(ir));
+			rv.d = ieee754dp_maddf(fd, fs, ft);
+			goto copcsr;
+		}
+
+		case fmsubf_op: {
+			union ieee754dp ft, fs, fd;
+
+			if (!cpu_has_mips_r6)
+				return SIGILL;
+
+			MIPS_FPU_EMU_INC_STATS(msubf_d);
+			DPFROMREG(ft, MIPSInst_FT(ir));
+			DPFROMREG(fs, MIPSInst_FS(ir));
+			DPFROMREG(fd, MIPSInst_FD(ir));
+			rv.d = ieee754dp_msubf(fd, fs, ft);
+			goto copcsr;
+		}
+
+		case frint_op: {
+			union ieee754dp fs;
+
+			if (!cpu_has_mips_r6)
+				return SIGILL;
+
+			MIPS_FPU_EMU_INC_STATS(rint_d);
+			DPFROMREG(fs, MIPSInst_FS(ir));
+			rv.d = ieee754dp_rint(fs);
+			goto copcsr;
+		}
+
+		case fclass_op: {
+			union ieee754dp fs;
+
+			if (!cpu_has_mips_r6)
+				return SIGILL;
+
+			MIPS_FPU_EMU_INC_STATS(class_d);
+			DPFROMREG(fs, MIPSInst_FS(ir));
+			rv.l = ieee754dp_2008class(fs);
+			rfmt = l_fmt;
+			goto copcsr;
+		}
+
+		case fmin_op: {
+			union ieee754dp fs, ft;
+
+			if (!cpu_has_mips_r6)
+				return SIGILL;
+
+			MIPS_FPU_EMU_INC_STATS(min_d);
+			DPFROMREG(ft, MIPSInst_FT(ir));
+			DPFROMREG(fs, MIPSInst_FS(ir));
+			rv.d = ieee754dp_fmin(fs, ft);
+			goto copcsr;
+		}
+
+		case fmina_op: {
+			union ieee754dp fs, ft;
+
+			if (!cpu_has_mips_r6)
+				return SIGILL;
+
+			MIPS_FPU_EMU_INC_STATS(mina_d);
+			DPFROMREG(ft, MIPSInst_FT(ir));
+			DPFROMREG(fs, MIPSInst_FS(ir));
+			rv.d = ieee754dp_fmina(fs, ft);
+			goto copcsr;
+		}
+
+		case fmax_op: {
+			union ieee754dp fs, ft;
+
+			if (!cpu_has_mips_r6)
+				return SIGILL;
+
+			MIPS_FPU_EMU_INC_STATS(max_d);
+			DPFROMREG(ft, MIPSInst_FT(ir));
+			DPFROMREG(fs, MIPSInst_FS(ir));
+			rv.d = ieee754dp_fmax(fs, ft);
+			goto copcsr;
+		}
+
+		case fmaxa_op: {
+			union ieee754dp fs, ft;
+
+			if (!cpu_has_mips_r6)
+				return SIGILL;
+
+			MIPS_FPU_EMU_INC_STATS(maxa_d);
+			DPFROMREG(ft, MIPSInst_FT(ir));
+			DPFROMREG(fs, MIPSInst_FS(ir));
+			rv.d = ieee754dp_fmaxa(fs, ft);
+			goto copcsr;
+		}
+
+		case fabs_op:
+			MIPS_FPU_EMU_INC_STATS(abs_d);
+			handler.u = ieee754dp_abs;
+			goto dcopuop;
+
+		case fneg_op:
+			MIPS_FPU_EMU_INC_STATS(neg_d);
+			handler.u = ieee754dp_neg;
+			goto dcopuop;
+
+		case fmov_op:
+			/* an easy one */
+			MIPS_FPU_EMU_INC_STATS(mov_d);
+			DPFROMREG(rv.d, MIPSInst_FS(ir));
+			goto copcsr;
+
+			/* binary op on handler */
+dcopbop:
+			DPFROMREG(fs, MIPSInst_FS(ir));
+			DPFROMREG(ft, MIPSInst_FT(ir));
+
+			rv.d = (*handler.b) (fs, ft);
+			goto copcsr;
+dcopuop:
+			DPFROMREG(fs, MIPSInst_FS(ir));
+			rv.d = (*handler.u) (fs);
+			goto copcsr;
+
+		/*
+		 * unary conv ops
+		 */
+		case fcvts_op:
+			MIPS_FPU_EMU_INC_STATS(cvt_s_d);
+			DPFROMREG(fs, MIPSInst_FS(ir));
+			rv.s = ieee754sp_fdp(fs);
+			rfmt = s_fmt;
+			goto copcsr;
+
+		case fcvtd_op:
+			return SIGILL;	/* not defined */
+
+		case fcvtw_op:
+			MIPS_FPU_EMU_INC_STATS(cvt_w_d);
+			DPFROMREG(fs, MIPSInst_FS(ir));
+			rv.w = ieee754dp_tint(fs);	/* wrong */
+			rfmt = w_fmt;
+			goto copcsr;
+
+		case fround_op:
+		case ftrunc_op:
+		case fceil_op:
+		case ffloor_op:
+			if (!cpu_has_mips_2_3_4_5_r)
+				return SIGILL;
+
+			if (MIPSInst_FUNC(ir) == fceil_op)
+				MIPS_FPU_EMU_INC_STATS(ceil_w_d);
+			if (MIPSInst_FUNC(ir) == ffloor_op)
+				MIPS_FPU_EMU_INC_STATS(floor_w_d);
+			if (MIPSInst_FUNC(ir) == fround_op)
+				MIPS_FPU_EMU_INC_STATS(round_w_d);
+			if (MIPSInst_FUNC(ir) == ftrunc_op)
+				MIPS_FPU_EMU_INC_STATS(trunc_w_d);
+
+			oldrm = ieee754_csr.rm;
+			DPFROMREG(fs, MIPSInst_FS(ir));
+			ieee754_csr.rm = MIPSInst_FUNC(ir);
+			rv.w = ieee754dp_tint(fs);
+			ieee754_csr.rm = oldrm;
+			rfmt = w_fmt;
+			goto copcsr;
+
+		case fsel_op:
+			if (!cpu_has_mips_r6)
+				return SIGILL;
+
+			MIPS_FPU_EMU_INC_STATS(sel_d);
+			DPFROMREG(fd, MIPSInst_FD(ir));
+			if (fd.bits & 0x1)
+				DPFROMREG(rv.d, MIPSInst_FT(ir));
+			else
+				DPFROMREG(rv.d, MIPSInst_FS(ir));
+			break;
+
+		case fcvtl_op:
+			if (!cpu_has_mips_3_4_5_64_r2_r6)
+				return SIGILL;
+
+			MIPS_FPU_EMU_INC_STATS(cvt_l_d);
+			DPFROMREG(fs, MIPSInst_FS(ir));
+			rv.l = ieee754dp_tlong(fs);
+			rfmt = l_fmt;
+			goto copcsr;
+
+		case froundl_op:
+		case ftruncl_op:
+		case fceill_op:
+		case ffloorl_op:
+			if (!cpu_has_mips_3_4_5_64_r2_r6)
+				return SIGILL;
+
+			if (MIPSInst_FUNC(ir) == fceill_op)
+				MIPS_FPU_EMU_INC_STATS(ceil_l_d);
+			if (MIPSInst_FUNC(ir) == ffloorl_op)
+				MIPS_FPU_EMU_INC_STATS(floor_l_d);
+			if (MIPSInst_FUNC(ir) == froundl_op)
+				MIPS_FPU_EMU_INC_STATS(round_l_d);
+			if (MIPSInst_FUNC(ir) == ftruncl_op)
+				MIPS_FPU_EMU_INC_STATS(trunc_l_d);
+
+			oldrm = ieee754_csr.rm;
+			DPFROMREG(fs, MIPSInst_FS(ir));
+			ieee754_csr.rm = MIPSInst_FUNC(ir);
+			rv.l = ieee754dp_tlong(fs);
+			ieee754_csr.rm = oldrm;
+			rfmt = l_fmt;
+			goto copcsr;
+
+		default:
+			if (!NO_R6EMU && MIPSInst_FUNC(ir) >= fcmp_op) {
+				unsigned int cmpop;
+				union ieee754dp fs, ft;
+
+				cmpop = MIPSInst_FUNC(ir) - fcmp_op;
+				DPFROMREG(fs, MIPSInst_FS(ir));
+				DPFROMREG(ft, MIPSInst_FT(ir));
+				rv.w = ieee754dp_cmp(fs, ft,
+					cmptab[cmpop & 0x7], cmpop & 0x8);
+				rfmt = -1;
+				if ((cmpop & 0x8)
+					&&
+					ieee754_cxtest
+					(IEEE754_INVALID_OPERATION))
+					rcsr = FPU_CSR_INV_X | FPU_CSR_INV_S;
+				else
+					goto copcsr;
+
+			}
+			else {
+				return SIGILL;
+			}
+			break;
+		}
+		break;
+	}
+
+	case w_fmt: {
+		union ieee754dp fs;
+
+		switch (MIPSInst_FUNC(ir)) {
+		case fcvts_op:
+			/* convert word to single precision real */
+			MIPS_FPU_EMU_INC_STATS(cvt_s_w);
+			SPFROMREG(fs, MIPSInst_FS(ir));
+			rv.s = ieee754sp_fint(fs.bits);
+			rfmt = s_fmt;
+			goto copcsr;
+		case fcvtd_op:
+			/* convert word to double precision real */
+			MIPS_FPU_EMU_INC_STATS(cvt_d_w);
+			SPFROMREG(fs, MIPSInst_FS(ir));
+			rv.d = ieee754dp_fint(fs.bits);
+			rfmt = d_fmt;
+			goto copcsr;
+		default: {
+			/* Emulating the new CMP.condn.fmt R6 instruction */
+#define CMPOP_MASK	0x7
+#define SIGN_BIT	(0x1 << 3)
+#define PREDICATE_BIT	(0x1 << 4)
+
+			int cmpop = MIPSInst_FUNC(ir) & CMPOP_MASK;
+			int sig = MIPSInst_FUNC(ir) & SIGN_BIT;
+			union ieee754sp fs, ft;
+
+			/* This is an R6 only instruction */
+			if (!cpu_has_mips_r6 ||
+			    (MIPSInst_FUNC(ir) & 0x20))
+				return SIGILL;
+
+			if (!sig) {
+				if (!(MIPSInst_FUNC(ir) & PREDICATE_BIT)) {
+					switch (cmpop) {
+					case 0:
+					MIPS_FPU_EMU_INC_STATS(cmp_af_s);
+					break;
+					case 1:
+					MIPS_FPU_EMU_INC_STATS(cmp_un_s);
+					break;
+					case 2:
+					MIPS_FPU_EMU_INC_STATS(cmp_eq_s);
+					break;
+					case 3:
+					MIPS_FPU_EMU_INC_STATS(cmp_ueq_s);
+					break;
+					case 4:
+					MIPS_FPU_EMU_INC_STATS(cmp_lt_s);
+					break;
+					case 5:
+					MIPS_FPU_EMU_INC_STATS(cmp_ult_s);
+					break;
+					case 6:
+					MIPS_FPU_EMU_INC_STATS(cmp_le_s);
+					break;
+					case 7:
+					MIPS_FPU_EMU_INC_STATS(cmp_ule_s);
+					break;
+					}
+				} else {
+					switch (cmpop) {
+					case 1:
+					MIPS_FPU_EMU_INC_STATS(cmp_or_s);
+					break;
+					case 2:
+					MIPS_FPU_EMU_INC_STATS(cmp_une_s);
+					break;
+					case 3:
+					MIPS_FPU_EMU_INC_STATS(cmp_ne_s);
+					break;
+					}
+				}
+			} else {
+				if (!(MIPSInst_FUNC(ir) & PREDICATE_BIT)) {
+					switch (cmpop) {
+					case 0:
+					MIPS_FPU_EMU_INC_STATS(cmp_saf_s);
+					break;
+					case 1:
+					MIPS_FPU_EMU_INC_STATS(cmp_sun_s);
+					break;
+					case 2:
+					MIPS_FPU_EMU_INC_STATS(cmp_seq_s);
+					break;
+					case 3:
+					MIPS_FPU_EMU_INC_STATS(cmp_sueq_s);
+					break;
+					case 4:
+					MIPS_FPU_EMU_INC_STATS(cmp_slt_s);
+					break;
+					case 5:
+					MIPS_FPU_EMU_INC_STATS(cmp_sult_s);
+					break;
+					case 6:
+					MIPS_FPU_EMU_INC_STATS(cmp_sle_s);
+					break;
+					case 7:
+					MIPS_FPU_EMU_INC_STATS(cmp_sule_s);
+					break;
+					}
+				} else {
+					switch (cmpop) {
+					case 1:
+					MIPS_FPU_EMU_INC_STATS(cmp_sor_s);
+					break;
+					case 2:
+					MIPS_FPU_EMU_INC_STATS(cmp_sune_s);
+					break;
+					case 3:
+					MIPS_FPU_EMU_INC_STATS(cmp_sne_s);
+					break;
+					}
+				}
+			}
+
+			/* fmt is w_fmt for single precision so fix it */
+			rfmt = s_fmt;
+			/* default to false */
+			rv.w = 0;
+
+			/* CMP.condn.S */
+			SPFROMREG(fs, MIPSInst_FS(ir));
+			SPFROMREG(ft, MIPSInst_FT(ir));
+
+			/* positive predicates */
+			if (!(MIPSInst_FUNC(ir) & PREDICATE_BIT)) {
+				if (ieee754sp_cmp(fs, ft, cmptab[cmpop],
+						  sig))
+				    rv.w = -1; /* true, all 1s */
+				if ((sig) &&
+				    ieee754_cxtest(IEEE754_INVALID_OPERATION))
+					rcsr = FPU_CSR_INV_X | FPU_CSR_INV_S;
+				else
+					goto copcsr;
+			} else {
+				/* negative predicates */
+				switch (cmpop) {
+				case 1:
+				case 2:
+				case 3:
+					if (ieee754sp_cmp(fs, ft,
+							  negative_cmptab[cmpop],
+							  sig))
+						rv.w = -1; /* true, all 1s */
+					if (sig &&
+					    ieee754_cxtest(IEEE754_INVALID_OPERATION))
+						rcsr = FPU_CSR_INV_X | FPU_CSR_INV_S;
+					else
+						goto copcsr;
+					break;
+				default:
+					/* Reserved R6 ops */
+					return SIGILL;
+				}
+			}
+			break;
+			}
+		}
+		break;
+	}
+
+	case l_fmt:
+
+		if (!cpu_has_mips_3_4_5_64_r2_r6)
+			return SIGILL;
+
+		DIFROMREG(bits, MIPSInst_FS(ir));
+
+		switch (MIPSInst_FUNC(ir)) {
+		case fcvts_op:
+			/* convert long to single precision real */
+			MIPS_FPU_EMU_INC_STATS(cvt_s_l);
+			rv.s = ieee754sp_flong(bits);
+			rfmt = s_fmt;
+			goto copcsr;
+		case fcvtd_op:
+			/* convert long to double precision real */
+			MIPS_FPU_EMU_INC_STATS(cvt_d_l);
+			rv.d = ieee754dp_flong(bits);
+			rfmt = d_fmt;
+			goto copcsr;
+		default: {
+			/* Emulating the new CMP.condn.fmt R6 instruction */
+			int cmpop = MIPSInst_FUNC(ir) & CMPOP_MASK;
+			int sig = MIPSInst_FUNC(ir) & SIGN_BIT;
+			union ieee754dp fs, ft;
+
+			if (!cpu_has_mips_r6 ||
+			    (MIPSInst_FUNC(ir) & 0x20))
+				return SIGILL;
+
+			if (!sig) {
+				if (!(MIPSInst_FUNC(ir) & PREDICATE_BIT)) {
+					switch (cmpop) {
+					case 0:
+					MIPS_FPU_EMU_INC_STATS(cmp_af_d);
+					break;
+					case 1:
+					MIPS_FPU_EMU_INC_STATS(cmp_un_d);
+					break;
+					case 2:
+					MIPS_FPU_EMU_INC_STATS(cmp_eq_d);
+					break;
+					case 3:
+					MIPS_FPU_EMU_INC_STATS(cmp_ueq_d);
+					break;
+					case 4:
+					MIPS_FPU_EMU_INC_STATS(cmp_lt_d);
+					break;
+					case 5:
+					MIPS_FPU_EMU_INC_STATS(cmp_ult_d);
+					break;
+					case 6:
+					MIPS_FPU_EMU_INC_STATS(cmp_le_d);
+					break;
+					case 7:
+					MIPS_FPU_EMU_INC_STATS(cmp_ule_d);
+					break;
+					}
+				} else {
+					switch (cmpop) {
+					case 1:
+					MIPS_FPU_EMU_INC_STATS(cmp_or_d);
+					break;
+					case 2:
+					MIPS_FPU_EMU_INC_STATS(cmp_une_d);
+					break;
+					case 3:
+					MIPS_FPU_EMU_INC_STATS(cmp_ne_d);
+					break;
+					}
+				}
+			} else {
+				if (!(MIPSInst_FUNC(ir) & PREDICATE_BIT)) {
+					switch (cmpop) {
+					case 0:
+					MIPS_FPU_EMU_INC_STATS(cmp_saf_d);
+					break;
+					case 1:
+					MIPS_FPU_EMU_INC_STATS(cmp_sun_d);
+					break;
+					case 2:
+					MIPS_FPU_EMU_INC_STATS(cmp_seq_d);
+					break;
+					case 3:
+					MIPS_FPU_EMU_INC_STATS(cmp_sueq_d);
+					break;
+					case 4:
+					MIPS_FPU_EMU_INC_STATS(cmp_slt_d);
+					break;
+					case 5:
+					MIPS_FPU_EMU_INC_STATS(cmp_sult_d);
+					break;
+					case 6:
+					MIPS_FPU_EMU_INC_STATS(cmp_sle_d);
+					break;
+					case 7:
+					MIPS_FPU_EMU_INC_STATS(cmp_sule_d);
+					break;
+					}
+				} else {
+					switch (cmpop) {
+					case 1:
+					MIPS_FPU_EMU_INC_STATS(cmp_sor_d);
+					break;
+					case 2:
+					MIPS_FPU_EMU_INC_STATS(cmp_sune_d);
+					break;
+					case 3:
+					MIPS_FPU_EMU_INC_STATS(cmp_sne_d);
+					break;
+					}
+				}
+			}
+
+			/* fmt is l_fmt for double precision so fix it */
+			rfmt = d_fmt;
+			/* default to false */
+			rv.l = 0;
+
+			/* CMP.condn.D */
+			DPFROMREG(fs, MIPSInst_FS(ir));
+			DPFROMREG(ft, MIPSInst_FT(ir));
+
+			/* positive predicates */
+			if (!(MIPSInst_FUNC(ir) & PREDICATE_BIT)) {
+				if (ieee754dp_cmp(fs, ft,
+						  cmptab[cmpop], sig))
+				    rv.l = -1LL; /* true, all 1s */
+				if (sig &&
+				    ieee754_cxtest(IEEE754_INVALID_OPERATION))
+					rcsr = FPU_CSR_INV_X | FPU_CSR_INV_S;
+				else
+					goto copcsr;
+			} else {
+				/* negative predicates */
+				switch (cmpop) {
+				case 1:
+				case 2:
+				case 3:
+					if (ieee754dp_cmp(fs, ft,
+							  negative_cmptab[cmpop],
+							  sig))
+						rv.l = -1LL; /* true, all 1s */
+					if (sig &&
+					    ieee754_cxtest(IEEE754_INVALID_OPERATION))
+						rcsr = FPU_CSR_INV_X | FPU_CSR_INV_S;
+					else
+						goto copcsr;
+					break;
+				default:
+					/* Reserved R6 ops */
+					return SIGILL;
+				}
+			}
+			break;
+			}
+		}
+		break;
+
+	default:
+		return SIGILL;
+	}
+
+	/*
+	 * Update the fpu CSR register for this operation.
+	 * If an exception is required, generate a tidy SIGFPE exception,
+	 * without updating the result register.
+	 * Note: cause exception bits do not accumulate, they are rewritten
+	 * for each op; only the flag/sticky bits accumulate.
+	 */
+	ctx->fcr31 = (ctx->fcr31 & ~FPU_CSR_ALL_X) | rcsr;
+	if ((ctx->fcr31 >> 5) & ctx->fcr31 & FPU_CSR_ALL_E) {
+		/*printk ("SIGFPE: FPU csr = %08x\n",ctx->fcr31); */
+		return SIGFPE;
+	}
+
+	/*
+	 * Now we can safely write the result back to the register file.
+	 */
+	switch (rfmt) {
+	case -1:
+
+		if (cpu_has_mips_4_5_r)
+			cbit = fpucondbit[MIPSInst_FD(ir) >> 2];
+		else
+			cbit = FPU_CSR_COND;
+		if (rv.w)
+			ctx->fcr31 |= cbit;
+		else
+			ctx->fcr31 &= ~cbit;
+		break;
+
+	case d_fmt:
+		DPTOREG(rv.d, MIPSInst_FD(ir));
+		break;
+	case s_fmt:
+		SPTOREG(rv.s, MIPSInst_FD(ir));
+		break;
+	case w_fmt:
+		SITOREG(rv.w, MIPSInst_FD(ir));
+		break;
+	case l_fmt:
+		if (!cpu_has_mips_3_4_5_64_r2_r6)
+			return SIGILL;
+
+		DITOREG(rv.l, MIPSInst_FD(ir));
+		break;
+	default:
+		return SIGILL;
+	}
+
+	return 0;
+}
+
+/*
+ * Emulate FPU instructions.
+ *
+ * If we use FPU hardware, then we have been typically called to handle
+ * an unimplemented operation, such as where an operand is a NaN or
+ * denormalized.  In that case exit the emulation loop after a single
+ * iteration so as to let hardware execute any subsequent instructions.
+ *
+ * If we have no FPU hardware or it has been disabled, then continue
+ * emulating floating-point instructions until one of these conditions
+ * has occurred:
+ *
+ * - a non-FPU instruction has been encountered,
+ *
+ * - an attempt to emulate has ended with a signal,
+ *
+ * - the ISA mode has been switched.
+ *
+ * We need to terminate the emulation loop if we got switched to the
+ * MIPS16 mode, whether supported or not, so that we do not attempt
+ * to emulate a MIPS16 instruction as a regular MIPS FPU instruction.
+ * Similarly if we got switched to the microMIPS mode and only the
+ * regular MIPS mode is supported, so that we do not attempt to emulate
+ * a microMIPS instruction as a regular MIPS FPU instruction.  Or if
+ * we got switched to the regular MIPS mode and only the microMIPS mode
+ * is supported, so that we do not attempt to emulate a regular MIPS
+ * instruction that should cause an Address Error exception instead.
+ * For simplicity we always terminate upon an ISA mode switch.
+ */
+int fpu_emulator_cop1Handler(struct pt_regs *xcp, struct mips_fpu_struct *ctx,
+	int has_fpu, void __user **fault_addr)
+{
+	unsigned long oldepc, prevepc;
+	struct mm_decoded_insn dec_insn;
+	u16 instr[4];
+	u16 *instr_ptr;
+	int sig = 0;
+
+	/*
+	 * Initialize context if it hasn't been used already, otherwise ensure
+	 * it has been saved to struct thread_struct.
+	 */
+	if (!init_fp_ctx(current))
+		lose_fpu(1);
+
+	oldepc = xcp->cp0_epc;
+	do {
+		prevepc = xcp->cp0_epc;
+
+		if (get_isa16_mode(prevepc) && cpu_has_mmips) {
+			/*
+			 * Get next 2 microMIPS instructions and convert them
+			 * into 32-bit instructions.
+			 */
+			if ((get_user(instr[0], (u16 __user *)msk_isa16_mode(xcp->cp0_epc))) ||
+			    (get_user(instr[1], (u16 __user *)msk_isa16_mode(xcp->cp0_epc + 2))) ||
+			    (get_user(instr[2], (u16 __user *)msk_isa16_mode(xcp->cp0_epc + 4))) ||
+			    (get_user(instr[3], (u16 __user *)msk_isa16_mode(xcp->cp0_epc + 6)))) {
+				MIPS_FPU_EMU_INC_STATS(errors);
+				return SIGBUS;
+			}
+			instr_ptr = instr;
+
+			/* Get first instruction. */
+			if (mm_insn_16bit(*instr_ptr)) {
+				/* Duplicate the half-word. */
+				dec_insn.insn = (*instr_ptr << 16) |
+					(*instr_ptr);
+				/* 16-bit instruction. */
+				dec_insn.pc_inc = 2;
+				instr_ptr += 1;
+			} else {
+				dec_insn.insn = (*instr_ptr << 16) |
+					*(instr_ptr+1);
+				/* 32-bit instruction. */
+				dec_insn.pc_inc = 4;
+				instr_ptr += 2;
+			}
+			/* Get second instruction. */
+			if (mm_insn_16bit(*instr_ptr)) {
+				/* Duplicate the half-word. */
+				dec_insn.next_insn = (*instr_ptr << 16) |
+					(*instr_ptr);
+				/* 16-bit instruction. */
+				dec_insn.next_pc_inc = 2;
+			} else {
+				dec_insn.next_insn = (*instr_ptr << 16) |
+					*(instr_ptr+1);
+				/* 32-bit instruction. */
+				dec_insn.next_pc_inc = 4;
+			}
+			dec_insn.micro_mips_mode = 1;
+		} else {
+			if ((get_user(dec_insn.insn,
+			    (mips_instruction __user *) xcp->cp0_epc)) ||
+			    (get_user(dec_insn.next_insn,
+			    (mips_instruction __user *)(xcp->cp0_epc+4)))) {
+				MIPS_FPU_EMU_INC_STATS(errors);
+				return SIGBUS;
+			}
+			dec_insn.pc_inc = 4;
+			dec_insn.next_pc_inc = 4;
+			dec_insn.micro_mips_mode = 0;
+		}
+
+		if ((dec_insn.insn == 0) ||
+		   ((dec_insn.pc_inc == 2) &&
+		   ((dec_insn.insn & 0xffff) == MM_NOP16)))
+			xcp->cp0_epc += dec_insn.pc_inc;	/* Skip NOPs */
+		else {
+			/*
+			 * The 'ieee754_csr' is an alias of ctx->fcr31.
+			 * No need to copy ctx->fcr31 to ieee754_csr.
+			 */
+			sig = cop1Emulate(xcp, ctx, dec_insn, fault_addr);
+		}
+
+		if (has_fpu)
+			break;
+		if (sig)
+			break;
+		/*
+		 * We have to check for the ISA bit explicitly here,
+		 * because `get_isa16_mode' may return 0 if support
+		 * for code compression has been globally disabled,
+		 * or otherwise we may produce the wrong signal or
+		 * even proceed successfully where we must not.
+		 */
+		if ((xcp->cp0_epc ^ prevepc) & 0x1)
+			break;
+
+		cond_resched();
+	} while (xcp->cp0_epc > prevepc);
+
+	/* SIGILL indicates a non-fpu instruction */
+	if (sig == SIGILL && xcp->cp0_epc != oldepc)
+		/* but if EPC has advanced, then ignore it */
+		sig = 0;
+
+	return sig;
+}
diff --git a/arch/mips/math-emu/dp_2008class.c b/arch/mips/math-emu/dp_2008class.c
new file mode 100644
index 000000000..81a0a63b1
--- /dev/null
+++ b/arch/mips/math-emu/dp_2008class.c
@@ -0,0 +1,52 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * IEEE754 floating point arithmetic
+ * double precision: CLASS.f
+ * FPR[fd] = class(FPR[fs])
+ *
+ * MIPS floating point support
+ * Copyright (C) 2015 Imagination Technologies, Ltd.
+ * Author: Markos Chandras <markos.chandras@imgtec.com>
+ */
+
+#include "ieee754dp.h"
+
+int ieee754dp_2008class(union ieee754dp x)
+{
+	COMPXDP;
+
+	EXPLODEXDP;
+
+	/*
+	 * 10 bit mask as follows:
+	 *
+	 * bit0 = SNAN
+	 * bit1 = QNAN
+	 * bit2 = -INF
+	 * bit3 = -NORM
+	 * bit4 = -DNORM
+	 * bit5 = -ZERO
+	 * bit6 = INF
+	 * bit7 = NORM
+	 * bit8 = DNORM
+	 * bit9 = ZERO
+	 */
+
+	switch(xc) {
+	case IEEE754_CLASS_SNAN:
+		return 0x01;
+	case IEEE754_CLASS_QNAN:
+		return 0x02;
+	case IEEE754_CLASS_INF:
+		return 0x04 << (xs ? 0 : 4);
+	case IEEE754_CLASS_NORM:
+		return 0x08 << (xs ? 0 : 4);
+	case IEEE754_CLASS_DNORM:
+		return 0x10 << (xs ? 0 : 4);
+	case IEEE754_CLASS_ZERO:
+		return 0x20 << (xs ? 0 : 4);
+	default:
+		pr_err("Unknown class: %d\n", xc);
+		return 0;
+	}
+}
diff --git a/arch/mips/math-emu/dp_add.c b/arch/mips/math-emu/dp_add.c
new file mode 100644
index 000000000..78504736b
--- /dev/null
+++ b/arch/mips/math-emu/dp_add.c
@@ -0,0 +1,165 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* IEEE754 floating point arithmetic
+ * double precision: common utilities
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ */
+
+#include "ieee754dp.h"
+
+union ieee754dp ieee754dp_add(union ieee754dp x, union ieee754dp y)
+{
+	int s;
+
+	COMPXDP;
+	COMPYDP;
+
+	EXPLODEXDP;
+	EXPLODEYDP;
+
+	ieee754_clearcx();
+
+	FLUSHXDP;
+	FLUSHYDP;
+
+	switch (CLPAIR(xc, yc)) {
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_SNAN):
+		return ieee754dp_nanxcpt(y);
+
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_INF):
+		return ieee754dp_nanxcpt(x);
+
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_QNAN):
+		return y;
+
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_INF):
+		return x;
+
+
+	/*
+	 * Infinity handling
+	 */
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_INF):
+		if (xs == ys)
+			return x;
+		ieee754_setcx(IEEE754_INVALID_OPERATION);
+		return ieee754dp_indef();
+
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_INF):
+		return y;
+
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_DNORM):
+		return x;
+
+	/*
+	 * Zero handling
+	 */
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_ZERO):
+		if (xs == ys)
+			return x;
+		else
+			return ieee754dp_zero(ieee754_csr.rm == FPU_CSR_RD);
+
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_ZERO):
+		return x;
+
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_DNORM):
+		return y;
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_DNORM):
+		DPDNORMX;
+		fallthrough;
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_DNORM):
+		DPDNORMY;
+		break;
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_NORM):
+		DPDNORMX;
+		break;
+
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_NORM):
+		break;
+	}
+	assert(xm & DP_HIDDEN_BIT);
+	assert(ym & DP_HIDDEN_BIT);
+
+	/*
+	 * Provide guard,round and stick bit space.
+	 */
+	xm <<= 3;
+	ym <<= 3;
+
+	if (xe > ye) {
+		/*
+		 * Have to shift y fraction right to align.
+		 */
+		s = xe - ye;
+		ym = XDPSRS(ym, s);
+		ye += s;
+	} else if (ye > xe) {
+		/*
+		 * Have to shift x fraction right to align.
+		 */
+		s = ye - xe;
+		xm = XDPSRS(xm, s);
+		xe += s;
+	}
+	assert(xe == ye);
+	assert(xe <= DP_EMAX);
+
+	if (xs == ys) {
+		/*
+		 * Generate 28 bit result of adding two 27 bit numbers
+		 * leaving result in xm, xs and xe.
+		 */
+		xm = xm + ym;
+
+		if (xm >> (DP_FBITS + 1 + 3)) { /* carry out */
+			xm = XDPSRS1(xm);
+			xe++;
+		}
+	} else {
+		if (xm >= ym) {
+			xm = xm - ym;
+		} else {
+			xm = ym - xm;
+			xs = ys;
+		}
+		if (xm == 0)
+			return ieee754dp_zero(ieee754_csr.rm == FPU_CSR_RD);
+
+		/*
+		 * Normalize to rounding precision.
+		 */
+		while ((xm >> (DP_FBITS + 3)) == 0) {
+			xm <<= 1;
+			xe--;
+		}
+	}
+
+	return ieee754dp_format(xs, xe, xm);
+}
diff --git a/arch/mips/math-emu/dp_cmp.c b/arch/mips/math-emu/dp_cmp.c
new file mode 100644
index 000000000..a59680b03
--- /dev/null
+++ b/arch/mips/math-emu/dp_cmp.c
@@ -0,0 +1,47 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* IEEE754 floating point arithmetic
+ * double precision: common utilities
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ */
+
+#include "ieee754dp.h"
+
+int ieee754dp_cmp(union ieee754dp x, union ieee754dp y, int cmp, int sig)
+{
+	s64 vx;
+	s64 vy;
+
+	COMPXDP;
+	COMPYDP;
+
+	EXPLODEXDP;
+	EXPLODEYDP;
+	FLUSHXDP;
+	FLUSHYDP;
+	ieee754_clearcx();	/* Even clear inexact flag here */
+
+	if (ieee754_class_nan(xc) || ieee754_class_nan(yc)) {
+		if (sig ||
+		    xc == IEEE754_CLASS_SNAN || yc == IEEE754_CLASS_SNAN)
+			ieee754_setcx(IEEE754_INVALID_OPERATION);
+		return (cmp & IEEE754_CUN) != 0;
+	} else {
+		vx = x.bits;
+		vy = y.bits;
+
+		if (vx < 0)
+			vx = -vx ^ DP_SIGN_BIT;
+		if (vy < 0)
+			vy = -vy ^ DP_SIGN_BIT;
+
+		if (vx < vy)
+			return (cmp & IEEE754_CLT) != 0;
+		else if (vx == vy)
+			return (cmp & IEEE754_CEQ) != 0;
+		else
+			return (cmp & IEEE754_CGT) != 0;
+	}
+}
diff --git a/arch/mips/math-emu/dp_div.c b/arch/mips/math-emu/dp_div.c
new file mode 100644
index 000000000..ac1ecc462
--- /dev/null
+++ b/arch/mips/math-emu/dp_div.c
@@ -0,0 +1,143 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* IEEE754 floating point arithmetic
+ * double precision: common utilities
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ */
+
+#include "ieee754dp.h"
+
+union ieee754dp ieee754dp_div(union ieee754dp x, union ieee754dp y)
+{
+	u64 rm;
+	int re;
+	u64 bm;
+
+	COMPXDP;
+	COMPYDP;
+
+	EXPLODEXDP;
+	EXPLODEYDP;
+
+	ieee754_clearcx();
+
+	FLUSHXDP;
+	FLUSHYDP;
+
+	switch (CLPAIR(xc, yc)) {
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_SNAN):
+		return ieee754dp_nanxcpt(y);
+
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_INF):
+		return ieee754dp_nanxcpt(x);
+
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_QNAN):
+		return y;
+
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_INF):
+		return x;
+
+
+	/*
+	 * Infinity handling
+	 */
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_INF):
+		ieee754_setcx(IEEE754_INVALID_OPERATION);
+		return ieee754dp_indef();
+
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_INF):
+		return ieee754dp_zero(xs ^ ys);
+
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_DNORM):
+		return ieee754dp_inf(xs ^ ys);
+
+	/*
+	 * Zero handling
+	 */
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_ZERO):
+		ieee754_setcx(IEEE754_INVALID_OPERATION);
+		return ieee754dp_indef();
+
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_ZERO):
+		ieee754_setcx(IEEE754_ZERO_DIVIDE);
+		return ieee754dp_inf(xs ^ ys);
+
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_DNORM):
+		return ieee754dp_zero(xs == ys ? 0 : 1);
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_DNORM):
+		DPDNORMX;
+		fallthrough;
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_DNORM):
+		DPDNORMY;
+		break;
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_NORM):
+		DPDNORMX;
+		break;
+
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_NORM):
+		break;
+	}
+	assert(xm & DP_HIDDEN_BIT);
+	assert(ym & DP_HIDDEN_BIT);
+
+	/* provide rounding space */
+	xm <<= 3;
+	ym <<= 3;
+
+	/* now the dirty work */
+
+	rm = 0;
+	re = xe - ye;
+
+	for (bm = DP_MBIT(DP_FBITS + 2); bm; bm >>= 1) {
+		if (xm >= ym) {
+			xm -= ym;
+			rm |= bm;
+			if (xm == 0)
+				break;
+		}
+		xm <<= 1;
+	}
+
+	rm <<= 1;
+	if (xm)
+		rm |= 1;	/* have remainder, set sticky */
+
+	assert(rm);
+
+	/*
+	 * Normalise rm to rounding precision ?
+	 */
+	while ((rm >> (DP_FBITS + 3)) == 0) {
+		rm <<= 1;
+		re--;
+	}
+
+	return ieee754dp_format(xs == ys ? 0 : 1, re, rm);
+}
diff --git a/arch/mips/math-emu/dp_fint.c b/arch/mips/math-emu/dp_fint.c
new file mode 100644
index 000000000..996b15ba0
--- /dev/null
+++ b/arch/mips/math-emu/dp_fint.c
@@ -0,0 +1,44 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* IEEE754 floating point arithmetic
+ * double precision: common utilities
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ */
+
+#include "ieee754dp.h"
+
+union ieee754dp ieee754dp_fint(int x)
+{
+	u64 xm;
+	int xe;
+	int xs;
+
+	ieee754_clearcx();
+
+	if (x == 0)
+		return ieee754dp_zero(0);
+	if (x == 1 || x == -1)
+		return ieee754dp_one(x < 0);
+	if (x == 10 || x == -10)
+		return ieee754dp_ten(x < 0);
+
+	xs = (x < 0);
+	if (xs) {
+		if (x == (1 << 31))
+			xm = ((unsigned) 1 << 31);	/* max neg can't be safely negated */
+		else
+			xm = -x;
+	} else {
+		xm = x;
+	}
+
+	/* normalize - result can never be inexact or overflow */
+	xe = DP_FBITS;
+	while ((xm >> DP_FBITS) == 0) {
+		xm <<= 1;
+		xe--;
+	}
+	return builddp(xs, xe + DP_EBIAS, xm & ~DP_HIDDEN_BIT);
+}
diff --git a/arch/mips/math-emu/dp_flong.c b/arch/mips/math-emu/dp_flong.c
new file mode 100644
index 000000000..681ee00c9
--- /dev/null
+++ b/arch/mips/math-emu/dp_flong.c
@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* IEEE754 floating point arithmetic
+ * double precision: common utilities
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ */
+
+#include "ieee754dp.h"
+
+union ieee754dp ieee754dp_flong(s64 x)
+{
+	u64 xm;
+	int xe;
+	int xs;
+
+	ieee754_clearcx();
+
+	if (x == 0)
+		return ieee754dp_zero(0);
+	if (x == 1 || x == -1)
+		return ieee754dp_one(x < 0);
+	if (x == 10 || x == -10)
+		return ieee754dp_ten(x < 0);
+
+	xs = (x < 0);
+	if (xs) {
+		if (x == (1ULL << 63))
+			xm = (1ULL << 63);	/* max neg can't be safely negated */
+		else
+			xm = -x;
+	} else {
+		xm = x;
+	}
+
+	/* normalize */
+	xe = DP_FBITS + 3;
+	if (xm >> (DP_FBITS + 1 + 3)) {
+		/* shunt out overflow bits */
+		while (xm >> (DP_FBITS + 1 + 3)) {
+			XDPSRSX1();
+		}
+	} else {
+		/* normalize in grs extended double precision */
+		while ((xm >> (DP_FBITS + 3)) == 0) {
+			xm <<= 1;
+			xe--;
+		}
+	}
+
+	return ieee754dp_format(xs, xe, xm);
+}
diff --git a/arch/mips/math-emu/dp_fmax.c b/arch/mips/math-emu/dp_fmax.c
new file mode 100644
index 000000000..126ec90bb
--- /dev/null
+++ b/arch/mips/math-emu/dp_fmax.c
@@ -0,0 +1,252 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * IEEE754 floating point arithmetic
+ * double precision: MIN{,A}.f
+ * MIN : Scalar Floating-Point Minimum
+ * MINA: Scalar Floating-Point argument with Minimum Absolute Value
+ *
+ * MIN.D : FPR[fd] = minNum(FPR[fs],FPR[ft])
+ * MINA.D: FPR[fd] = maxNumMag(FPR[fs],FPR[ft])
+ *
+ * MIPS floating point support
+ * Copyright (C) 2015 Imagination Technologies, Ltd.
+ * Author: Markos Chandras <markos.chandras@imgtec.com>
+ */
+
+#include "ieee754dp.h"
+
+union ieee754dp ieee754dp_fmax(union ieee754dp x, union ieee754dp y)
+{
+	COMPXDP;
+	COMPYDP;
+
+	EXPLODEXDP;
+	EXPLODEYDP;
+
+	FLUSHXDP;
+	FLUSHYDP;
+
+	ieee754_clearcx();
+
+	switch (CLPAIR(xc, yc)) {
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_SNAN):
+		return ieee754dp_nanxcpt(y);
+
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_INF):
+		return ieee754dp_nanxcpt(x);
+
+	/*
+	 * Quiet NaN handling
+	 */
+
+	/*
+	 *    The case of both inputs quiet NaNs
+	 */
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_QNAN):
+		return x;
+
+	/*
+	 *    The cases of exactly one input quiet NaN (numbers
+	 *    are here preferred as returned values to NaNs)
+	 */
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_QNAN):
+		return x;
+
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_INF):
+		return y;
+
+	/*
+	 * Infinity and zero handling
+	 */
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_ZERO):
+		return xs ? y : x;
+
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_DNORM):
+		return ys ? x : y;
+
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_ZERO):
+		return ieee754dp_zero(xs & ys);
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_DNORM):
+		DPDNORMX;
+		fallthrough;
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_DNORM):
+		DPDNORMY;
+		break;
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_NORM):
+		DPDNORMX;
+	}
+
+	/* Finally get to do some computation */
+
+	assert(xm & DP_HIDDEN_BIT);
+	assert(ym & DP_HIDDEN_BIT);
+
+	/* Compare signs */
+	if (xs > ys)
+		return y;
+	else if (xs < ys)
+		return x;
+
+	/* Signs of inputs are equal, let's compare exponents */
+	if (xs == 0) {
+		/* Inputs are both positive */
+		if (xe > ye)
+			return x;
+		else if (xe < ye)
+			return y;
+	} else {
+		/* Inputs are both negative */
+		if (xe > ye)
+			return y;
+		else if (xe < ye)
+			return x;
+	}
+
+	/* Signs and exponents of inputs are equal, let's compare mantissas */
+	if (xs == 0) {
+		/* Inputs are both positive, with equal signs and exponents */
+		if (xm <= ym)
+			return y;
+		return x;
+	}
+	/* Inputs are both negative, with equal signs and exponents */
+	if (xm <= ym)
+		return x;
+	return y;
+}
+
+union ieee754dp ieee754dp_fmaxa(union ieee754dp x, union ieee754dp y)
+{
+	COMPXDP;
+	COMPYDP;
+
+	EXPLODEXDP;
+	EXPLODEYDP;
+
+	FLUSHXDP;
+	FLUSHYDP;
+
+	ieee754_clearcx();
+
+	switch (CLPAIR(xc, yc)) {
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_SNAN):
+		return ieee754dp_nanxcpt(y);
+
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_INF):
+		return ieee754dp_nanxcpt(x);
+
+	/*
+	 * Quiet NaN handling
+	 */
+
+	/*
+	 *    The case of both inputs quiet NaNs
+	 */
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_QNAN):
+		return x;
+
+	/*
+	 *    The cases of exactly one input quiet NaN (numbers
+	 *    are here preferred as returned values to NaNs)
+	 */
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_QNAN):
+		return x;
+
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_INF):
+		return y;
+
+	/*
+	 * Infinity and zero handling
+	 */
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_INF):
+		return ieee754dp_inf(xs & ys);
+
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_ZERO):
+		return x;
+
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_DNORM):
+		return y;
+
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_ZERO):
+		return ieee754dp_zero(xs & ys);
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_DNORM):
+		DPDNORMX;
+		fallthrough;
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_DNORM):
+		DPDNORMY;
+		break;
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_NORM):
+		DPDNORMX;
+	}
+
+	/* Finally get to do some computation */
+
+	assert(xm & DP_HIDDEN_BIT);
+	assert(ym & DP_HIDDEN_BIT);
+
+	/* Compare exponent */
+	if (xe > ye)
+		return x;
+	else if (xe < ye)
+		return y;
+
+	/* Compare mantissa */
+	if (xm < ym)
+		return y;
+	else if (xm > ym)
+		return x;
+	else if (xs == 0)
+		return x;
+	return y;
+}
diff --git a/arch/mips/math-emu/dp_fmin.c b/arch/mips/math-emu/dp_fmin.c
new file mode 100644
index 000000000..35ded4c45
--- /dev/null
+++ b/arch/mips/math-emu/dp_fmin.c
@@ -0,0 +1,252 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * IEEE754 floating point arithmetic
+ * double precision: MIN{,A}.f
+ * MIN : Scalar Floating-Point Minimum
+ * MINA: Scalar Floating-Point argument with Minimum Absolute Value
+ *
+ * MIN.D : FPR[fd] = minNum(FPR[fs],FPR[ft])
+ * MINA.D: FPR[fd] = maxNumMag(FPR[fs],FPR[ft])
+ *
+ * MIPS floating point support
+ * Copyright (C) 2015 Imagination Technologies, Ltd.
+ * Author: Markos Chandras <markos.chandras@imgtec.com>
+ */
+
+#include "ieee754dp.h"
+
+union ieee754dp ieee754dp_fmin(union ieee754dp x, union ieee754dp y)
+{
+	COMPXDP;
+	COMPYDP;
+
+	EXPLODEXDP;
+	EXPLODEYDP;
+
+	FLUSHXDP;
+	FLUSHYDP;
+
+	ieee754_clearcx();
+
+	switch (CLPAIR(xc, yc)) {
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_SNAN):
+		return ieee754dp_nanxcpt(y);
+
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_INF):
+		return ieee754dp_nanxcpt(x);
+
+	/*
+	 * Quiet NaN handling
+	 */
+
+	/*
+	 *    The case of both inputs quiet NaNs
+	 */
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_QNAN):
+		return x;
+
+	/*
+	 *    The cases of exactly one input quiet NaN (numbers
+	 *    are here preferred as returned values to NaNs)
+	 */
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_QNAN):
+		return x;
+
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_INF):
+		return y;
+
+	/*
+	 * Infinity and zero handling
+	 */
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_ZERO):
+		return xs ? x : y;
+
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_DNORM):
+		return ys ? y : x;
+
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_ZERO):
+		return ieee754dp_zero(xs | ys);
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_DNORM):
+		DPDNORMX;
+		fallthrough;
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_DNORM):
+		DPDNORMY;
+		break;
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_NORM):
+		DPDNORMX;
+	}
+
+	/* Finally get to do some computation */
+
+	assert(xm & DP_HIDDEN_BIT);
+	assert(ym & DP_HIDDEN_BIT);
+
+	/* Compare signs */
+	if (xs > ys)
+		return x;
+	else if (xs < ys)
+		return y;
+
+	/* Signs of inputs are the same, let's compare exponents */
+	if (xs == 0) {
+		/* Inputs are both positive */
+		if (xe > ye)
+			return y;
+		else if (xe < ye)
+			return x;
+	} else {
+		/* Inputs are both negative */
+		if (xe > ye)
+			return x;
+		else if (xe < ye)
+			return y;
+	}
+
+	/* Signs and exponents of inputs are equal, let's compare mantissas */
+	if (xs == 0) {
+		/* Inputs are both positive, with equal signs and exponents */
+		if (xm <= ym)
+			return x;
+		return y;
+	}
+	/* Inputs are both negative, with equal signs and exponents */
+	if (xm <= ym)
+		return y;
+	return x;
+}
+
+union ieee754dp ieee754dp_fmina(union ieee754dp x, union ieee754dp y)
+{
+	COMPXDP;
+	COMPYDP;
+
+	EXPLODEXDP;
+	EXPLODEYDP;
+
+	FLUSHXDP;
+	FLUSHYDP;
+
+	ieee754_clearcx();
+
+	switch (CLPAIR(xc, yc)) {
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_SNAN):
+		return ieee754dp_nanxcpt(y);
+
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_INF):
+		return ieee754dp_nanxcpt(x);
+
+	/*
+	 * Quiet NaN handling
+	 */
+
+	/*
+	 *    The case of both inputs quiet NaNs
+	 */
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_QNAN):
+		return x;
+
+	/*
+	 *    The cases of exactly one input quiet NaN (numbers
+	 *    are here preferred as returned values to NaNs)
+	 */
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_QNAN):
+		return x;
+
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_INF):
+		return y;
+
+	/*
+	 * Infinity and zero handling
+	 */
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_INF):
+		return ieee754dp_inf(xs | ys);
+
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_ZERO):
+		return y;
+
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_DNORM):
+		return x;
+
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_ZERO):
+		return ieee754dp_zero(xs | ys);
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_DNORM):
+		DPDNORMX;
+		fallthrough;
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_DNORM):
+		DPDNORMY;
+		break;
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_NORM):
+		DPDNORMX;
+	}
+
+	/* Finally get to do some computation */
+
+	assert(xm & DP_HIDDEN_BIT);
+	assert(ym & DP_HIDDEN_BIT);
+
+	/* Compare exponent */
+	if (xe > ye)
+		return y;
+	else if (xe < ye)
+		return x;
+
+	/* Compare mantissa */
+	if (xm < ym)
+		return x;
+	else if (xm > ym)
+		return y;
+	else if (xs == 1)
+		return x;
+	return y;
+}
diff --git a/arch/mips/math-emu/dp_fsp.c b/arch/mips/math-emu/dp_fsp.c
new file mode 100644
index 000000000..be8a929c4
--- /dev/null
+++ b/arch/mips/math-emu/dp_fsp.c
@@ -0,0 +1,63 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* IEEE754 floating point arithmetic
+ * double precision: common utilities
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ */
+
+#include "ieee754sp.h"
+#include "ieee754dp.h"
+
+static inline union ieee754dp ieee754dp_nan_fsp(int xs, u64 xm)
+{
+	return builddp(xs, DP_EMAX + 1 + DP_EBIAS,
+		       xm << (DP_FBITS - SP_FBITS));
+}
+
+union ieee754dp ieee754dp_fsp(union ieee754sp x)
+{
+	COMPXSP;
+
+	EXPLODEXSP;
+
+	ieee754_clearcx();
+
+	FLUSHXSP;
+
+	switch (xc) {
+	case IEEE754_CLASS_SNAN:
+		return ieee754dp_nanxcpt(ieee754dp_nan_fsp(xs, xm));
+
+	case IEEE754_CLASS_QNAN:
+		return ieee754dp_nan_fsp(xs, xm);
+
+	case IEEE754_CLASS_INF:
+		return ieee754dp_inf(xs);
+
+	case IEEE754_CLASS_ZERO:
+		return ieee754dp_zero(xs);
+
+	case IEEE754_CLASS_DNORM:
+		/* normalize */
+		while ((xm >> SP_FBITS) == 0) {
+			xm <<= 1;
+			xe--;
+		}
+		break;
+
+	case IEEE754_CLASS_NORM:
+		break;
+	}
+
+	/*
+	 * Can't possibly overflow,underflow, or need rounding
+	 */
+
+	/* drop the hidden bit */
+	xm &= ~SP_HIDDEN_BIT;
+
+	return builddp(xs, xe + DP_EBIAS,
+		       (u64) xm << (DP_FBITS - SP_FBITS));
+}
diff --git a/arch/mips/math-emu/dp_maddf.c b/arch/mips/math-emu/dp_maddf.c
new file mode 100644
index 000000000..931e66f68
--- /dev/null
+++ b/arch/mips/math-emu/dp_maddf.c
@@ -0,0 +1,358 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * IEEE754 floating point arithmetic
+ * double precision: MADDF.f (Fused Multiply Add)
+ * MADDF.fmt: FPR[fd] = FPR[fd] + (FPR[fs] x FPR[ft])
+ *
+ * MIPS floating point support
+ * Copyright (C) 2015 Imagination Technologies, Ltd.
+ * Author: Markos Chandras <markos.chandras@imgtec.com>
+ */
+
+#include "ieee754dp.h"
+
+
+/* 128 bits shift right logical with rounding. */
+static void srl128(u64 *hptr, u64 *lptr, int count)
+{
+	u64 low;
+
+	if (count >= 128) {
+		*lptr = *hptr != 0 || *lptr != 0;
+		*hptr = 0;
+	} else if (count >= 64) {
+		if (count == 64) {
+			*lptr = *hptr | (*lptr != 0);
+		} else {
+			low = *lptr;
+			*lptr = *hptr >> (count - 64);
+			*lptr |= (*hptr << (128 - count)) != 0 || low != 0;
+		}
+		*hptr = 0;
+	} else {
+		low = *lptr;
+		*lptr = low >> count | *hptr << (64 - count);
+		*lptr |= (low << (64 - count)) != 0;
+		*hptr = *hptr >> count;
+	}
+}
+
+static union ieee754dp _dp_maddf(union ieee754dp z, union ieee754dp x,
+				 union ieee754dp y, enum maddf_flags flags)
+{
+	int re;
+	int rs;
+	unsigned int lxm;
+	unsigned int hxm;
+	unsigned int lym;
+	unsigned int hym;
+	u64 lrm;
+	u64 hrm;
+	u64 lzm;
+	u64 hzm;
+	u64 t;
+	u64 at;
+	int s;
+
+	COMPXDP;
+	COMPYDP;
+	COMPZDP;
+
+	EXPLODEXDP;
+	EXPLODEYDP;
+	EXPLODEZDP;
+
+	FLUSHXDP;
+	FLUSHYDP;
+	FLUSHZDP;
+
+	ieee754_clearcx();
+
+	rs = xs ^ ys;
+	if (flags & MADDF_NEGATE_PRODUCT)
+		rs ^= 1;
+	if (flags & MADDF_NEGATE_ADDITION)
+		zs ^= 1;
+
+	/*
+	 * Handle the cases when at least one of x, y or z is a NaN.
+	 * Order of precedence is sNaN, qNaN and z, x, y.
+	 */
+	if (zc == IEEE754_CLASS_SNAN)
+		return ieee754dp_nanxcpt(z);
+	if (xc == IEEE754_CLASS_SNAN)
+		return ieee754dp_nanxcpt(x);
+	if (yc == IEEE754_CLASS_SNAN)
+		return ieee754dp_nanxcpt(y);
+	if (zc == IEEE754_CLASS_QNAN)
+		return z;
+	if (xc == IEEE754_CLASS_QNAN)
+		return x;
+	if (yc == IEEE754_CLASS_QNAN)
+		return y;
+
+	if (zc == IEEE754_CLASS_DNORM)
+		DPDNORMZ;
+	/* ZERO z cases are handled separately below */
+
+	switch (CLPAIR(xc, yc)) {
+
+	/*
+	 * Infinity handling
+	 */
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_INF):
+		ieee754_setcx(IEEE754_INVALID_OPERATION);
+		return ieee754dp_indef();
+
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_INF):
+		if ((zc == IEEE754_CLASS_INF) && (zs != rs)) {
+			/*
+			 * Cases of addition of infinities with opposite signs
+			 * or subtraction of infinities with same signs.
+			 */
+			ieee754_setcx(IEEE754_INVALID_OPERATION);
+			return ieee754dp_indef();
+		}
+		/*
+		 * z is here either not an infinity, or an infinity having the
+		 * same sign as product (x*y). The result must be an infinity,
+		 * and its sign is determined only by the sign of product (x*y).
+		 */
+		return ieee754dp_inf(rs);
+
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_ZERO):
+		if (zc == IEEE754_CLASS_INF)
+			return ieee754dp_inf(zs);
+		if (zc == IEEE754_CLASS_ZERO) {
+			/* Handle cases +0 + (-0) and similar ones. */
+			if (zs == rs)
+				/*
+				 * Cases of addition of zeros of equal signs
+				 * or subtraction of zeroes of opposite signs.
+				 * The sign of the resulting zero is in any
+				 * such case determined only by the sign of z.
+				 */
+				return z;
+
+			return ieee754dp_zero(ieee754_csr.rm == FPU_CSR_RD);
+		}
+		/* x*y is here 0, and z is not 0, so just return z */
+		return z;
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_DNORM):
+		DPDNORMX;
+		fallthrough;
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_DNORM):
+		if (zc == IEEE754_CLASS_INF)
+			return ieee754dp_inf(zs);
+		DPDNORMY;
+		break;
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_NORM):
+		if (zc == IEEE754_CLASS_INF)
+			return ieee754dp_inf(zs);
+		DPDNORMX;
+		break;
+
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_NORM):
+		if (zc == IEEE754_CLASS_INF)
+			return ieee754dp_inf(zs);
+		/* continue to real computations */
+	}
+
+	/* Finally get to do some computation */
+
+	/*
+	 * Do the multiplication bit first
+	 *
+	 * rm = xm * ym, re = xe + ye basically
+	 *
+	 * At this point xm and ym should have been normalized.
+	 */
+	assert(xm & DP_HIDDEN_BIT);
+	assert(ym & DP_HIDDEN_BIT);
+
+	re = xe + ye;
+
+	/* shunt to top of word */
+	xm <<= 64 - (DP_FBITS + 1);
+	ym <<= 64 - (DP_FBITS + 1);
+
+	/*
+	 * Multiply 64 bits xm and ym to give 128 bits result in hrm:lrm.
+	 */
+
+	lxm = xm;
+	hxm = xm >> 32;
+	lym = ym;
+	hym = ym >> 32;
+
+	lrm = DPXMULT(lxm, lym);
+	hrm = DPXMULT(hxm, hym);
+
+	t = DPXMULT(lxm, hym);
+
+	at = lrm + (t << 32);
+	hrm += at < lrm;
+	lrm = at;
+
+	hrm = hrm + (t >> 32);
+
+	t = DPXMULT(hxm, lym);
+
+	at = lrm + (t << 32);
+	hrm += at < lrm;
+	lrm = at;
+
+	hrm = hrm + (t >> 32);
+
+	/* Put explicit bit at bit 126 if necessary */
+	if ((int64_t)hrm < 0) {
+		lrm = (hrm << 63) | (lrm >> 1);
+		hrm = hrm >> 1;
+		re++;
+	}
+
+	assert(hrm & (1 << 62));
+
+	if (zc == IEEE754_CLASS_ZERO) {
+		/*
+		 * Move explicit bit from bit 126 to bit 55 since the
+		 * ieee754dp_format code expects the mantissa to be
+		 * 56 bits wide (53 + 3 rounding bits).
+		 */
+		srl128(&hrm, &lrm, (126 - 55));
+		return ieee754dp_format(rs, re, lrm);
+	}
+
+	/* Move explicit bit from bit 52 to bit 126 */
+	lzm = 0;
+	hzm = zm << 10;
+	assert(hzm & (1 << 62));
+
+	/* Make the exponents the same */
+	if (ze > re) {
+		/*
+		 * Have to shift y fraction right to align.
+		 */
+		s = ze - re;
+		srl128(&hrm, &lrm, s);
+		re += s;
+	} else if (re > ze) {
+		/*
+		 * Have to shift x fraction right to align.
+		 */
+		s = re - ze;
+		srl128(&hzm, &lzm, s);
+		ze += s;
+	}
+	assert(ze == re);
+	assert(ze <= DP_EMAX);
+
+	/* Do the addition */
+	if (zs == rs) {
+		/*
+		 * Generate 128 bit result by adding two 127 bit numbers
+		 * leaving result in hzm:lzm, zs and ze.
+		 */
+		hzm = hzm + hrm + (lzm > (lzm + lrm));
+		lzm = lzm + lrm;
+		if ((int64_t)hzm < 0) {        /* carry out */
+			srl128(&hzm, &lzm, 1);
+			ze++;
+		}
+	} else {
+		if (hzm > hrm || (hzm == hrm && lzm >= lrm)) {
+			hzm = hzm - hrm - (lzm < lrm);
+			lzm = lzm - lrm;
+		} else {
+			hzm = hrm - hzm - (lrm < lzm);
+			lzm = lrm - lzm;
+			zs = rs;
+		}
+		if (lzm == 0 && hzm == 0)
+			return ieee754dp_zero(ieee754_csr.rm == FPU_CSR_RD);
+
+		/*
+		 * Put explicit bit at bit 126 if necessary.
+		 */
+		if (hzm == 0) {
+			/* left shift by 63 or 64 bits */
+			if ((int64_t)lzm < 0) {
+				/* MSB of lzm is the explicit bit */
+				hzm = lzm >> 1;
+				lzm = lzm << 63;
+				ze -= 63;
+			} else {
+				hzm = lzm;
+				lzm = 0;
+				ze -= 64;
+			}
+		}
+
+		t = 0;
+		while ((hzm >> (62 - t)) == 0)
+			t++;
+
+		assert(t <= 62);
+		if (t) {
+			hzm = hzm << t | lzm >> (64 - t);
+			lzm = lzm << t;
+			ze -= t;
+		}
+	}
+
+	/*
+	 * Move explicit bit from bit 126 to bit 55 since the
+	 * ieee754dp_format code expects the mantissa to be
+	 * 56 bits wide (53 + 3 rounding bits).
+	 */
+	srl128(&hzm, &lzm, (126 - 55));
+
+	return ieee754dp_format(zs, ze, lzm);
+}
+
+union ieee754dp ieee754dp_maddf(union ieee754dp z, union ieee754dp x,
+				union ieee754dp y)
+{
+	return _dp_maddf(z, x, y, 0);
+}
+
+union ieee754dp ieee754dp_msubf(union ieee754dp z, union ieee754dp x,
+				union ieee754dp y)
+{
+	return _dp_maddf(z, x, y, MADDF_NEGATE_PRODUCT);
+}
+
+union ieee754dp ieee754dp_madd(union ieee754dp z, union ieee754dp x,
+				union ieee754dp y)
+{
+	return _dp_maddf(z, x, y, 0);
+}
+
+union ieee754dp ieee754dp_msub(union ieee754dp z, union ieee754dp x,
+				union ieee754dp y)
+{
+	return _dp_maddf(z, x, y, MADDF_NEGATE_ADDITION);
+}
+
+union ieee754dp ieee754dp_nmadd(union ieee754dp z, union ieee754dp x,
+				union ieee754dp y)
+{
+	return _dp_maddf(z, x, y, MADDF_NEGATE_PRODUCT|MADDF_NEGATE_ADDITION);
+}
+
+union ieee754dp ieee754dp_nmsub(union ieee754dp z, union ieee754dp x,
+				union ieee754dp y)
+{
+	return _dp_maddf(z, x, y, MADDF_NEGATE_PRODUCT);
+}
diff --git a/arch/mips/math-emu/dp_mul.c b/arch/mips/math-emu/dp_mul.c
new file mode 100644
index 000000000..8a671bb7a
--- /dev/null
+++ b/arch/mips/math-emu/dp_mul.c
@@ -0,0 +1,159 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* IEEE754 floating point arithmetic
+ * double precision: common utilities
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ */
+
+#include "ieee754dp.h"
+
+union ieee754dp ieee754dp_mul(union ieee754dp x, union ieee754dp y)
+{
+	int re;
+	int rs;
+	u64 rm;
+	unsigned int lxm;
+	unsigned int hxm;
+	unsigned int lym;
+	unsigned int hym;
+	u64 lrm;
+	u64 hrm;
+	u64 t;
+	u64 at;
+
+	COMPXDP;
+	COMPYDP;
+
+	EXPLODEXDP;
+	EXPLODEYDP;
+
+	ieee754_clearcx();
+
+	FLUSHXDP;
+	FLUSHYDP;
+
+	switch (CLPAIR(xc, yc)) {
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_SNAN):
+		return ieee754dp_nanxcpt(y);
+
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_INF):
+		return ieee754dp_nanxcpt(x);
+
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_QNAN):
+		return y;
+
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_INF):
+		return x;
+
+
+	/*
+	 * Infinity handling
+	 */
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_INF):
+		ieee754_setcx(IEEE754_INVALID_OPERATION);
+		return ieee754dp_indef();
+
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_INF):
+		return ieee754dp_inf(xs ^ ys);
+
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_ZERO):
+		return ieee754dp_zero(xs ^ ys);
+
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_DNORM):
+		DPDNORMX;
+		fallthrough;
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_DNORM):
+		DPDNORMY;
+		break;
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_NORM):
+		DPDNORMX;
+		break;
+
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_NORM):
+		break;
+	}
+	/* rm = xm * ym, re = xe+ye basically */
+	assert(xm & DP_HIDDEN_BIT);
+	assert(ym & DP_HIDDEN_BIT);
+
+	re = xe + ye;
+	rs = xs ^ ys;
+
+	/* shunt to top of word */
+	xm <<= 64 - (DP_FBITS + 1);
+	ym <<= 64 - (DP_FBITS + 1);
+
+	/*
+	 * Multiply 64 bits xm, ym to give high 64 bits rm with stickness.
+	 */
+
+	lxm = xm;
+	hxm = xm >> 32;
+	lym = ym;
+	hym = ym >> 32;
+
+	lrm = DPXMULT(lxm, lym);
+	hrm = DPXMULT(hxm, hym);
+
+	t = DPXMULT(lxm, hym);
+
+	at = lrm + (t << 32);
+	hrm += at < lrm;
+	lrm = at;
+
+	hrm = hrm + (t >> 32);
+
+	t = DPXMULT(hxm, lym);
+
+	at = lrm + (t << 32);
+	hrm += at < lrm;
+	lrm = at;
+
+	hrm = hrm + (t >> 32);
+
+	rm = hrm | (lrm != 0);
+
+	/*
+	 * Sticky shift down to normal rounding precision.
+	 */
+	if ((s64) rm < 0) {
+		rm = (rm >> (64 - (DP_FBITS + 1 + 3))) |
+		     ((rm << (DP_FBITS + 1 + 3)) != 0);
+		re++;
+	} else {
+		rm = (rm >> (64 - (DP_FBITS + 1 + 3 + 1))) |
+		     ((rm << (DP_FBITS + 1 + 3 + 1)) != 0);
+	}
+	assert(rm & (DP_HIDDEN_BIT << 3));
+
+	return ieee754dp_format(rs, re, rm);
+}
diff --git a/arch/mips/math-emu/dp_rint.c b/arch/mips/math-emu/dp_rint.c
new file mode 100644
index 000000000..7f30b7a30
--- /dev/null
+++ b/arch/mips/math-emu/dp_rint.c
@@ -0,0 +1,78 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* IEEE754 floating point arithmetic
+ * double precision: common utilities
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ * Copyright (C) 2017 Imagination Technologies, Ltd.
+ * Author: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
+ */
+
+#include "ieee754dp.h"
+
+union ieee754dp ieee754dp_rint(union ieee754dp x)
+{
+	union ieee754dp ret;
+	u64 residue;
+	int sticky;
+	int round;
+	int odd;
+
+	COMPXDP;
+
+	ieee754_clearcx();
+
+	EXPLODEXDP;
+	FLUSHXDP;
+
+	if (xc == IEEE754_CLASS_SNAN)
+		return ieee754dp_nanxcpt(x);
+
+	if ((xc == IEEE754_CLASS_QNAN) ||
+	    (xc == IEEE754_CLASS_INF) ||
+	    (xc == IEEE754_CLASS_ZERO))
+		return x;
+
+	if (xe >= DP_FBITS)
+		return x;
+
+	if (xe < -1) {
+		residue = xm;
+		round = 0;
+		sticky = residue != 0;
+		xm = 0;
+	} else {
+		residue = xm << (64 - DP_FBITS + xe);
+		round = (residue >> 63) != 0;
+		sticky = (residue << 1) != 0;
+		xm >>= DP_FBITS - xe;
+	}
+
+	odd = (xm & 0x1) != 0x0;
+
+	switch (ieee754_csr.rm) {
+	case FPU_CSR_RN:	/* toward nearest */
+		if (round && (sticky || odd))
+			xm++;
+		break;
+	case FPU_CSR_RZ:	/* toward zero */
+		break;
+	case FPU_CSR_RU:	/* toward +infinity */
+		if ((round || sticky) && !xs)
+			xm++;
+		break;
+	case FPU_CSR_RD:	/* toward -infinity */
+		if ((round || sticky) && xs)
+			xm++;
+		break;
+	}
+
+	if (round || sticky)
+		ieee754_setcx(IEEE754_INEXACT);
+
+	ret = ieee754dp_flong(xm);
+	DPSIGN(ret) = xs;
+
+	return ret;
+}
diff --git a/arch/mips/math-emu/dp_simple.c b/arch/mips/math-emu/dp_simple.c
new file mode 100644
index 000000000..b063aad7d
--- /dev/null
+++ b/arch/mips/math-emu/dp_simple.c
@@ -0,0 +1,49 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* IEEE754 floating point arithmetic
+ * double precision: common utilities
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ */
+
+#include "ieee754dp.h"
+
+union ieee754dp ieee754dp_neg(union ieee754dp x)
+{
+	union ieee754dp y;
+
+	if (ieee754_csr.abs2008) {
+		y = x;
+		DPSIGN(y) = !DPSIGN(x);
+	} else {
+		unsigned int oldrm;
+
+		oldrm = ieee754_csr.rm;
+		ieee754_csr.rm = FPU_CSR_RD;
+		y = ieee754dp_sub(ieee754dp_zero(0), x);
+		ieee754_csr.rm = oldrm;
+	}
+	return y;
+}
+
+union ieee754dp ieee754dp_abs(union ieee754dp x)
+{
+	union ieee754dp y;
+
+	if (ieee754_csr.abs2008) {
+		y = x;
+		DPSIGN(y) = 0;
+	} else {
+		unsigned int oldrm;
+
+		oldrm = ieee754_csr.rm;
+		ieee754_csr.rm = FPU_CSR_RD;
+		if (DPSIGN(x))
+			y = ieee754dp_sub(ieee754dp_zero(0), x);
+		else
+			y = ieee754dp_add(ieee754dp_zero(0), x);
+		ieee754_csr.rm = oldrm;
+	}
+	return y;
+}
diff --git a/arch/mips/math-emu/dp_sqrt.c b/arch/mips/math-emu/dp_sqrt.c
new file mode 100644
index 000000000..1ee38f824
--- /dev/null
+++ b/arch/mips/math-emu/dp_sqrt.c
@@ -0,0 +1,152 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* IEEE754 floating point arithmetic
+ * double precision square root
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ */
+
+#include "ieee754dp.h"
+
+static const unsigned int table[] = {
+	0, 1204, 3062, 5746, 9193, 13348, 18162, 23592,
+	29598, 36145, 43202, 50740, 58733, 67158, 75992,
+	85215, 83599, 71378, 60428, 50647, 41945, 34246,
+	27478, 21581, 16499, 12183, 8588, 5674, 3403,
+	1742, 661, 130
+};
+
+union ieee754dp ieee754dp_sqrt(union ieee754dp x)
+{
+	struct _ieee754_csr oldcsr;
+	union ieee754dp y, z, t;
+	unsigned int scalx, yh;
+	COMPXDP;
+
+	EXPLODEXDP;
+	ieee754_clearcx();
+	FLUSHXDP;
+
+	/* x == INF or NAN? */
+	switch (xc) {
+	case IEEE754_CLASS_SNAN:
+		return ieee754dp_nanxcpt(x);
+
+	case IEEE754_CLASS_QNAN:
+		/* sqrt(Nan) = Nan */
+		return x;
+
+	case IEEE754_CLASS_ZERO:
+		/* sqrt(0) = 0 */
+		return x;
+
+	case IEEE754_CLASS_INF:
+		if (xs) {
+			/* sqrt(-Inf) = Nan */
+			ieee754_setcx(IEEE754_INVALID_OPERATION);
+			return ieee754dp_indef();
+		}
+		/* sqrt(+Inf) = Inf */
+		return x;
+
+	case IEEE754_CLASS_DNORM:
+		DPDNORMX;
+		fallthrough;
+	case IEEE754_CLASS_NORM:
+		if (xs) {
+			/* sqrt(-x) = Nan */
+			ieee754_setcx(IEEE754_INVALID_OPERATION);
+			return ieee754dp_indef();
+		}
+		break;
+	}
+
+	/* save old csr; switch off INX enable & flag; set RN rounding */
+	oldcsr = ieee754_csr;
+	ieee754_csr.mx &= ~IEEE754_INEXACT;
+	ieee754_csr.sx &= ~IEEE754_INEXACT;
+	ieee754_csr.rm = FPU_CSR_RN;
+
+	/* adjust exponent to prevent overflow */
+	scalx = 0;
+	if (xe > 512) {		/* x > 2**-512? */
+		xe -= 512;	/* x = x / 2**512 */
+		scalx += 256;
+	} else if (xe < -512) { /* x < 2**-512? */
+		xe += 512;	/* x = x * 2**512 */
+		scalx -= 256;
+	}
+
+	x = builddp(0, xe + DP_EBIAS, xm & ~DP_HIDDEN_BIT);
+	y = x;
+
+	/* magic initial approximation to almost 8 sig. bits */
+	yh = y.bits >> 32;
+	yh = (yh >> 1) + 0x1ff80000;
+	yh = yh - table[(yh >> 15) & 31];
+	y.bits = ((u64) yh << 32) | (y.bits & 0xffffffff);
+
+	/* Heron's rule once with correction to improve to ~18 sig. bits */
+	/* t=x/y; y=y+t; py[n0]=py[n0]-0x00100006; py[n1]=0; */
+	t = ieee754dp_div(x, y);
+	y = ieee754dp_add(y, t);
+	y.bits -= 0x0010000600000000LL;
+	y.bits &= 0xffffffff00000000LL;
+
+	/* triple to almost 56 sig. bits: y ~= sqrt(x) to within 1 ulp */
+	/* t=y*y; z=t;	pt[n0]+=0x00100000; t+=z; z=(x-z)*y; */
+	t = ieee754dp_mul(y, y);
+	z = t;
+	t.bexp += 0x001;
+	t = ieee754dp_add(t, z);
+	z = ieee754dp_mul(ieee754dp_sub(x, z), y);
+
+	/* t=z/(t+x) ;	pt[n0]+=0x00100000; y+=t; */
+	t = ieee754dp_div(z, ieee754dp_add(t, x));
+	t.bexp += 0x001;
+	y = ieee754dp_add(y, t);
+
+	/* twiddle last bit to force y correctly rounded */
+
+	/* set RZ, clear INEX flag */
+	ieee754_csr.rm = FPU_CSR_RZ;
+	ieee754_csr.sx &= ~IEEE754_INEXACT;
+
+	/* t=x/y; ...chopped quotient, possibly inexact */
+	t = ieee754dp_div(x, y);
+
+	if (ieee754_csr.sx & IEEE754_INEXACT || t.bits != y.bits) {
+
+		if (!(ieee754_csr.sx & IEEE754_INEXACT))
+			/* t = t-ulp */
+			t.bits -= 1;
+
+		/* add inexact to result status */
+		oldcsr.cx |= IEEE754_INEXACT;
+		oldcsr.sx |= IEEE754_INEXACT;
+
+		switch (oldcsr.rm) {
+		case FPU_CSR_RU:
+			y.bits += 1;
+			fallthrough;
+		case FPU_CSR_RN:
+			t.bits += 1;
+			break;
+		}
+
+		/* y=y+t; ...chopped sum */
+		y = ieee754dp_add(y, t);
+
+		/* adjust scalx for correctly rounded sqrt(x) */
+		scalx -= 1;
+	}
+
+	/* py[n0]=py[n0]+scalx; ...scale back y */
+	y.bexp += scalx;
+
+	/* restore rounding mode, possibly set inexact */
+	ieee754_csr = oldcsr;
+
+	return y;
+}
diff --git a/arch/mips/math-emu/dp_sub.c b/arch/mips/math-emu/dp_sub.c
new file mode 100644
index 000000000..08474ad2a
--- /dev/null
+++ b/arch/mips/math-emu/dp_sub.c
@@ -0,0 +1,172 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* IEEE754 floating point arithmetic
+ * double precision: common utilities
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ */
+
+#include "ieee754dp.h"
+
+union ieee754dp ieee754dp_sub(union ieee754dp x, union ieee754dp y)
+{
+	int s;
+
+	COMPXDP;
+	COMPYDP;
+
+	EXPLODEXDP;
+	EXPLODEYDP;
+
+	ieee754_clearcx();
+
+	FLUSHXDP;
+	FLUSHYDP;
+
+	switch (CLPAIR(xc, yc)) {
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_SNAN):
+		return ieee754dp_nanxcpt(y);
+
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_INF):
+		return ieee754dp_nanxcpt(x);
+
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_QNAN):
+		return y;
+
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_INF):
+		return x;
+
+
+	/*
+	 * Infinity handling
+	 */
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_INF):
+		if (xs != ys)
+			return x;
+		ieee754_setcx(IEEE754_INVALID_OPERATION);
+		return ieee754dp_indef();
+
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_INF):
+		return ieee754dp_inf(ys ^ 1);
+
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_DNORM):
+		return x;
+
+	/*
+	 * Zero handling
+	 */
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_ZERO):
+		if (xs != ys)
+			return x;
+		else
+			return ieee754dp_zero(ieee754_csr.rm == FPU_CSR_RD);
+
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_ZERO):
+		return x;
+
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_DNORM):
+		/* quick fix up */
+		DPSIGN(y) ^= 1;
+		return y;
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_DNORM):
+		DPDNORMX;
+		fallthrough;
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_DNORM):
+		/* normalize ym,ye */
+		DPDNORMY;
+		break;
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_NORM):
+		/* normalize xm,xe */
+		DPDNORMX;
+		break;
+
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_NORM):
+		break;
+	}
+	/* flip sign of y and handle as add */
+	ys ^= 1;
+
+	assert(xm & DP_HIDDEN_BIT);
+	assert(ym & DP_HIDDEN_BIT);
+
+
+	/* provide guard,round and stick bit dpace */
+	xm <<= 3;
+	ym <<= 3;
+
+	if (xe > ye) {
+		/*
+		 * Have to shift y fraction right to align
+		 */
+		s = xe - ye;
+		ym = XDPSRS(ym, s);
+		ye += s;
+	} else if (ye > xe) {
+		/*
+		 * Have to shift x fraction right to align
+		 */
+		s = ye - xe;
+		xm = XDPSRS(xm, s);
+		xe += s;
+	}
+	assert(xe == ye);
+	assert(xe <= DP_EMAX);
+
+	if (xs == ys) {
+		/* generate 28 bit result of adding two 27 bit numbers
+		 */
+		xm = xm + ym;
+
+		if (xm >> (DP_FBITS + 1 + 3)) { /* carry out */
+			xm = XDPSRS1(xm);	/* shift preserving sticky */
+			xe++;
+		}
+	} else {
+		if (xm >= ym) {
+			xm = xm - ym;
+		} else {
+			xm = ym - xm;
+			xs = ys;
+		}
+		if (xm == 0) {
+			if (ieee754_csr.rm == FPU_CSR_RD)
+				return ieee754dp_zero(1);	/* round negative inf. => sign = -1 */
+			else
+				return ieee754dp_zero(0);	/* other round modes   => sign = 1 */
+		}
+
+		/* normalize to rounding precision
+		 */
+		while ((xm >> (DP_FBITS + 3)) == 0) {
+			xm <<= 1;
+			xe--;
+		}
+	}
+
+	return ieee754dp_format(xs, xe, xm);
+}
diff --git a/arch/mips/math-emu/dp_tint.c b/arch/mips/math-emu/dp_tint.c
new file mode 100644
index 000000000..0e6ad35e7
--- /dev/null
+++ b/arch/mips/math-emu/dp_tint.c
@@ -0,0 +1,96 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* IEEE754 floating point arithmetic
+ * double precision: common utilities
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ */
+
+#include "ieee754dp.h"
+
+int ieee754dp_tint(union ieee754dp x)
+{
+	u64 residue;
+	int round;
+	int sticky;
+	int odd;
+
+	COMPXDP;
+
+	ieee754_clearcx();
+
+	EXPLODEXDP;
+	FLUSHXDP;
+
+	switch (xc) {
+	case IEEE754_CLASS_SNAN:
+	case IEEE754_CLASS_QNAN:
+		ieee754_setcx(IEEE754_INVALID_OPERATION);
+		return ieee754si_indef();
+
+	case IEEE754_CLASS_INF:
+		ieee754_setcx(IEEE754_INVALID_OPERATION);
+		return ieee754si_overflow(xs);
+
+	case IEEE754_CLASS_ZERO:
+		return 0;
+
+	case IEEE754_CLASS_DNORM:
+	case IEEE754_CLASS_NORM:
+		break;
+	}
+	if (xe > 31) {
+		/* Set invalid. We will only use overflow for floating
+		   point overflow */
+		ieee754_setcx(IEEE754_INVALID_OPERATION);
+		return ieee754si_overflow(xs);
+	}
+	/* oh gawd */
+	if (xe > DP_FBITS) {
+		xm <<= xe - DP_FBITS;
+	} else if (xe < DP_FBITS) {
+		if (xe < -1) {
+			residue = xm;
+			round = 0;
+			sticky = residue != 0;
+			xm = 0;
+		} else {
+			residue = xm << (64 - DP_FBITS + xe);
+			round = (residue >> 63) != 0;
+			sticky = (residue << 1) != 0;
+			xm >>= DP_FBITS - xe;
+		}
+		/* Note: At this point upper 32 bits of xm are guaranteed
+		   to be zero */
+		odd = (xm & 0x1) != 0x0;
+		switch (ieee754_csr.rm) {
+		case FPU_CSR_RN:
+			if (round && (sticky || odd))
+				xm++;
+			break;
+		case FPU_CSR_RZ:
+			break;
+		case FPU_CSR_RU:	/* toward +Infinity */
+			if ((round || sticky) && !xs)
+				xm++;
+			break;
+		case FPU_CSR_RD:	/* toward -Infinity */
+			if ((round || sticky) && xs)
+				xm++;
+			break;
+		}
+		/* look for valid corner case 0x80000000 */
+		if ((xm >> 31) != 0 && (xs == 0 || xm != 0x80000000)) {
+			/* This can happen after rounding */
+			ieee754_setcx(IEEE754_INVALID_OPERATION);
+			return ieee754si_overflow(xs);
+		}
+		if (round || sticky)
+			ieee754_setcx(IEEE754_INEXACT);
+	}
+	if (xs)
+		return -xm;
+	else
+		return xm;
+}
diff --git a/arch/mips/math-emu/dp_tlong.c b/arch/mips/math-emu/dp_tlong.c
new file mode 100644
index 000000000..c61ef02d4
--- /dev/null
+++ b/arch/mips/math-emu/dp_tlong.c
@@ -0,0 +1,100 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* IEEE754 floating point arithmetic
+ * double precision: common utilities
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ */
+
+#include "ieee754dp.h"
+
+s64 ieee754dp_tlong(union ieee754dp x)
+{
+	u64 residue;
+	int round;
+	int sticky;
+	int odd;
+
+	COMPXDP;
+
+	ieee754_clearcx();
+
+	EXPLODEXDP;
+	FLUSHXDP;
+
+	switch (xc) {
+	case IEEE754_CLASS_SNAN:
+	case IEEE754_CLASS_QNAN:
+		ieee754_setcx(IEEE754_INVALID_OPERATION);
+		return ieee754di_indef();
+
+	case IEEE754_CLASS_INF:
+		ieee754_setcx(IEEE754_INVALID_OPERATION);
+		return ieee754di_overflow(xs);
+
+	case IEEE754_CLASS_ZERO:
+		return 0;
+
+	case IEEE754_CLASS_DNORM:
+	case IEEE754_CLASS_NORM:
+		break;
+	}
+	if (xe >= 63) {
+		/* look for valid corner case */
+		if (xe == 63 && xs && xm == DP_HIDDEN_BIT)
+			return -0x8000000000000000LL;
+		/* Set invalid. We will only use overflow for floating
+		   point overflow */
+		ieee754_setcx(IEEE754_INVALID_OPERATION);
+		return ieee754di_overflow(xs);
+	}
+	/* oh gawd */
+	if (xe > DP_FBITS) {
+		xm <<= xe - DP_FBITS;
+	} else if (xe < DP_FBITS) {
+		if (xe < -1) {
+			residue = xm;
+			round = 0;
+			sticky = residue != 0;
+			xm = 0;
+		} else {
+			/* Shifting a u64 64 times does not work,
+			* so we do it in two steps. Be aware that xe
+			* may be -1 */
+			residue = xm << (xe + 1);
+			residue <<= 63 - DP_FBITS;
+			round = (residue >> 63) != 0;
+			sticky = (residue << 1) != 0;
+			xm >>= DP_FBITS - xe;
+		}
+		odd = (xm & 0x1) != 0x0;
+		switch (ieee754_csr.rm) {
+		case FPU_CSR_RN:
+			if (round && (sticky || odd))
+				xm++;
+			break;
+		case FPU_CSR_RZ:
+			break;
+		case FPU_CSR_RU:	/* toward +Infinity */
+			if ((round || sticky) && !xs)
+				xm++;
+			break;
+		case FPU_CSR_RD:	/* toward -Infinity */
+			if ((round || sticky) && xs)
+				xm++;
+			break;
+		}
+		if ((xm >> 63) != 0) {
+			/* This can happen after rounding */
+			ieee754_setcx(IEEE754_INVALID_OPERATION);
+			return ieee754di_overflow(xs);
+		}
+		if (round || sticky)
+			ieee754_setcx(IEEE754_INEXACT);
+	}
+	if (xs)
+		return -xm;
+	else
+		return xm;
+}
diff --git a/arch/mips/math-emu/dsemul.c b/arch/mips/math-emu/dsemul.c
new file mode 100644
index 000000000..e02bd20b6
--- /dev/null
+++ b/arch/mips/math-emu/dsemul.c
@@ -0,0 +1,305 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/err.h>
+#include <linux/slab.h>
+#include <linux/mm_types.h>
+#include <linux/sched/task.h>
+
+#include <asm/branch.h>
+#include <asm/cacheflush.h>
+#include <asm/fpu_emulator.h>
+#include <asm/inst.h>
+#include <asm/mipsregs.h>
+#include <linux/uaccess.h>
+
+/**
+ * struct emuframe - The 'emulation' frame structure
+ * @emul:	The instruction to 'emulate'.
+ * @badinst:	A break instruction to cause a return to the kernel.
+ *
+ * This structure defines the frames placed within the delay slot emulation
+ * page in response to a call to mips_dsemul(). Each thread may be allocated
+ * only one frame at any given time. The kernel stores within it the
+ * instruction to be 'emulated' followed by a break instruction, then
+ * executes the frame in user mode. The break causes a trap to the kernel
+ * which leads to do_dsemulret() being called unless the instruction in
+ * @emul causes a trap itself, is a branch, or a signal is delivered to
+ * the thread. In these cases the allocated frame will either be reused by
+ * a subsequent delay slot 'emulation', or be freed during signal delivery or
+ * upon thread exit.
+ *
+ * This approach is used because:
+ *
+ * - Actually emulating all instructions isn't feasible. We would need to
+ *   be able to handle instructions from all revisions of the MIPS ISA,
+ *   all ASEs & all vendor instruction set extensions. This would be a
+ *   whole lot of work & continual maintenance burden as new instructions
+ *   are introduced, and in the case of some vendor extensions may not
+ *   even be possible. Thus we need to take the approach of actually
+ *   executing the instruction.
+ *
+ * - We must execute the instruction within user context. If we were to
+ *   execute the instruction in kernel mode then it would have access to
+ *   kernel resources without very careful checks, leaving us with a
+ *   high potential for security or stability issues to arise.
+ *
+ * - We used to place the frame on the users stack, but this requires
+ *   that the stack be executable. This is bad for security so the
+ *   per-process page is now used instead.
+ *
+ * - The instruction in @emul may be something entirely invalid for a
+ *   delay slot. The user may (intentionally or otherwise) place a branch
+ *   in a delay slot, or a kernel mode instruction, or something else
+ *   which generates an exception. Thus we can't rely upon the break in
+ *   @badinst always being hit. For this reason we track the index of the
+ *   frame allocated to each thread, allowing us to clean it up at later
+ *   points such as signal delivery or thread exit.
+ *
+ * - The user may generate a fake struct emuframe if they wish, invoking
+ *   the BRK_MEMU break instruction themselves. We must therefore not
+ *   trust that BRK_MEMU means there's actually a valid frame allocated
+ *   to the thread, and must not allow the user to do anything they
+ *   couldn't already.
+ */
+struct emuframe {
+	mips_instruction	emul;
+	mips_instruction	badinst;
+};
+
+static const int emupage_frame_count = PAGE_SIZE / sizeof(struct emuframe);
+
+static inline __user struct emuframe *dsemul_page(void)
+{
+	return (__user struct emuframe *)STACK_TOP;
+}
+
+static int alloc_emuframe(void)
+{
+	mm_context_t *mm_ctx = &current->mm->context;
+	int idx;
+
+retry:
+	spin_lock(&mm_ctx->bd_emupage_lock);
+
+	/* Ensure we have an allocation bitmap */
+	if (!mm_ctx->bd_emupage_allocmap) {
+		mm_ctx->bd_emupage_allocmap = bitmap_zalloc(emupage_frame_count,
+							    GFP_ATOMIC);
+		if (!mm_ctx->bd_emupage_allocmap) {
+			idx = BD_EMUFRAME_NONE;
+			goto out_unlock;
+		}
+	}
+
+	/* Attempt to allocate a single bit/frame */
+	idx = bitmap_find_free_region(mm_ctx->bd_emupage_allocmap,
+				      emupage_frame_count, 0);
+	if (idx < 0) {
+		/*
+		 * Failed to allocate a frame. We'll wait until one becomes
+		 * available. We unlock the page so that other threads actually
+		 * get the opportunity to free their frames, which means
+		 * technically the result of bitmap_full may be incorrect.
+		 * However the worst case is that we repeat all this and end up
+		 * back here again.
+		 */
+		spin_unlock(&mm_ctx->bd_emupage_lock);
+		if (!wait_event_killable(mm_ctx->bd_emupage_queue,
+			!bitmap_full(mm_ctx->bd_emupage_allocmap,
+				     emupage_frame_count)))
+			goto retry;
+
+		/* Received a fatal signal - just give in */
+		return BD_EMUFRAME_NONE;
+	}
+
+	/* Success! */
+	pr_debug("allocate emuframe %d to %d\n", idx, current->pid);
+out_unlock:
+	spin_unlock(&mm_ctx->bd_emupage_lock);
+	return idx;
+}
+
+static void free_emuframe(int idx, struct mm_struct *mm)
+{
+	mm_context_t *mm_ctx = &mm->context;
+
+	spin_lock(&mm_ctx->bd_emupage_lock);
+
+	pr_debug("free emuframe %d from %d\n", idx, current->pid);
+	bitmap_clear(mm_ctx->bd_emupage_allocmap, idx, 1);
+
+	/* If some thread is waiting for a frame, now's its chance */
+	wake_up(&mm_ctx->bd_emupage_queue);
+
+	spin_unlock(&mm_ctx->bd_emupage_lock);
+}
+
+static bool within_emuframe(struct pt_regs *regs)
+{
+	unsigned long base = (unsigned long)dsemul_page();
+
+	if (regs->cp0_epc < base)
+		return false;
+	if (regs->cp0_epc >= (base + PAGE_SIZE))
+		return false;
+
+	return true;
+}
+
+bool dsemul_thread_cleanup(struct task_struct *tsk)
+{
+	int fr_idx;
+
+	/* Clear any allocated frame, retrieving its index */
+	fr_idx = atomic_xchg(&tsk->thread.bd_emu_frame, BD_EMUFRAME_NONE);
+
+	/* If no frame was allocated, we're done */
+	if (fr_idx == BD_EMUFRAME_NONE)
+		return false;
+
+	task_lock(tsk);
+
+	/* Free the frame that this thread had allocated */
+	if (tsk->mm)
+		free_emuframe(fr_idx, tsk->mm);
+
+	task_unlock(tsk);
+	return true;
+}
+
+bool dsemul_thread_rollback(struct pt_regs *regs)
+{
+	struct emuframe __user *fr;
+	int fr_idx;
+
+	/* Do nothing if we're not executing from a frame */
+	if (!within_emuframe(regs))
+		return false;
+
+	/* Find the frame being executed */
+	fr_idx = atomic_read(&current->thread.bd_emu_frame);
+	if (fr_idx == BD_EMUFRAME_NONE)
+		return false;
+	fr = &dsemul_page()[fr_idx];
+
+	/*
+	 * If the PC is at the emul instruction, roll back to the branch. If
+	 * PC is at the badinst (break) instruction, we've already emulated the
+	 * instruction so progress to the continue PC. If it's anything else
+	 * then something is amiss & the user has branched into some other area
+	 * of the emupage - we'll free the allocated frame anyway.
+	 */
+	if (msk_isa16_mode(regs->cp0_epc) == (unsigned long)&fr->emul)
+		regs->cp0_epc = current->thread.bd_emu_branch_pc;
+	else if (msk_isa16_mode(regs->cp0_epc) == (unsigned long)&fr->badinst)
+		regs->cp0_epc = current->thread.bd_emu_cont_pc;
+
+	atomic_set(&current->thread.bd_emu_frame, BD_EMUFRAME_NONE);
+	free_emuframe(fr_idx, current->mm);
+	return true;
+}
+
+void dsemul_mm_cleanup(struct mm_struct *mm)
+{
+	mm_context_t *mm_ctx = &mm->context;
+
+	bitmap_free(mm_ctx->bd_emupage_allocmap);
+}
+
+int mips_dsemul(struct pt_regs *regs, mips_instruction ir,
+		unsigned long branch_pc, unsigned long cont_pc)
+{
+	int isa16 = get_isa16_mode(regs->cp0_epc);
+	mips_instruction break_math;
+	unsigned long fr_uaddr;
+	struct emuframe fr;
+	int fr_idx, ret;
+
+	/* NOP is easy */
+	if (ir == 0)
+		return -1;
+
+	/* microMIPS instructions */
+	if (isa16) {
+		union mips_instruction insn = { .word = ir };
+
+		/* NOP16 aka MOVE16 $0, $0 */
+		if ((ir >> 16) == MM_NOP16)
+			return -1;
+
+		/* ADDIUPC */
+		if (insn.mm_a_format.opcode == mm_addiupc_op) {
+			unsigned int rs;
+			s32 v;
+
+			rs = (((insn.mm_a_format.rs + 0xe) & 0xf) + 2);
+			v = regs->cp0_epc & ~3;
+			v += insn.mm_a_format.simmediate << 2;
+			regs->regs[rs] = (long)v;
+			return -1;
+		}
+	}
+
+	pr_debug("dsemul 0x%08lx cont at 0x%08lx\n", regs->cp0_epc, cont_pc);
+
+	/* Allocate a frame if we don't already have one */
+	fr_idx = atomic_read(&current->thread.bd_emu_frame);
+	if (fr_idx == BD_EMUFRAME_NONE)
+		fr_idx = alloc_emuframe();
+	if (fr_idx == BD_EMUFRAME_NONE)
+		return SIGBUS;
+
+	/* Retrieve the appropriately encoded break instruction */
+	break_math = BREAK_MATH(isa16);
+
+	/* Write the instructions to the frame */
+	if (isa16) {
+		union mips_instruction _emul = {
+			.halfword = { ir >> 16, ir }
+		};
+		union mips_instruction _badinst = {
+			.halfword = { break_math >> 16, break_math }
+		};
+
+		fr.emul = _emul.word;
+		fr.badinst = _badinst.word;
+	} else {
+		fr.emul = ir;
+		fr.badinst = break_math;
+	}
+
+	/* Write the frame to user memory */
+	fr_uaddr = (unsigned long)&dsemul_page()[fr_idx];
+	ret = access_process_vm(current, fr_uaddr, &fr, sizeof(fr),
+				FOLL_FORCE | FOLL_WRITE);
+	if (unlikely(ret != sizeof(fr))) {
+		MIPS_FPU_EMU_INC_STATS(errors);
+		free_emuframe(fr_idx, current->mm);
+		return SIGBUS;
+	}
+
+	/* Record the PC of the branch, PC to continue from & frame index */
+	current->thread.bd_emu_branch_pc = branch_pc;
+	current->thread.bd_emu_cont_pc = cont_pc;
+	atomic_set(&current->thread.bd_emu_frame, fr_idx);
+
+	/* Change user register context to execute the frame */
+	regs->cp0_epc = fr_uaddr | isa16;
+
+	return 0;
+}
+
+bool do_dsemulret(struct pt_regs *xcp)
+{
+	/* Cleanup the allocated frame, returning if there wasn't one */
+	if (!dsemul_thread_cleanup(current)) {
+		MIPS_FPU_EMU_INC_STATS(errors);
+		return false;
+	}
+
+	/* Set EPC to return to post-branch instruction */
+	xcp->cp0_epc = current->thread.bd_emu_cont_pc;
+	pr_debug("dsemulret to 0x%08lx\n", xcp->cp0_epc);
+	MIPS_FPU_EMU_INC_STATS(ds_emul);
+	return true;
+}
diff --git a/arch/mips/math-emu/ieee754.c b/arch/mips/math-emu/ieee754.c
new file mode 100644
index 000000000..0ba5dfbd4
--- /dev/null
+++ b/arch/mips/math-emu/ieee754.c
@@ -0,0 +1,83 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* ieee754 floating point arithmetic
+ * single and double precision
+ *
+ * BUGS
+ * not much dp done
+ * doesn't generate IEEE754_INEXACT
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ */
+
+#include <linux/compiler.h>
+
+#include "ieee754.h"
+#include "ieee754sp.h"
+#include "ieee754dp.h"
+
+/*
+ * Special constants
+ */
+
+/*
+ * Older GCC requires the inner braces for initialization of union ieee754dp's
+ * anonymous struct member.  Without an error will result.
+ */
+#define xPCNST(s, b, m, ebias)						\
+{									\
+	{								\
+		.sign	= (s),						\
+		.bexp	= (b) + ebias,					\
+		.mant	= (m)						\
+	}								\
+}
+
+#define DPCNST(s, b, m)							\
+	xPCNST(s, b, m, DP_EBIAS)
+
+const union ieee754dp __ieee754dp_spcvals[] = {
+	DPCNST(0, DP_EMIN - 1, 0x0000000000000ULL),	/* + zero   */
+	DPCNST(1, DP_EMIN - 1, 0x0000000000000ULL),	/* - zero   */
+	DPCNST(0, 0,	       0x0000000000000ULL),	/* + 1.0   */
+	DPCNST(1, 0,	       0x0000000000000ULL),	/* - 1.0   */
+	DPCNST(0, 3,           0x4000000000000ULL),	/* + 10.0   */
+	DPCNST(1, 3,           0x4000000000000ULL),	/* - 10.0   */
+	DPCNST(0, DP_EMAX + 1, 0x0000000000000ULL),	/* + infinity */
+	DPCNST(1, DP_EMAX + 1, 0x0000000000000ULL),	/* - infinity */
+	DPCNST(0, DP_EMAX + 1, 0x7FFFFFFFFFFFFULL),	/* + ind legacy qNaN */
+	DPCNST(0, DP_EMAX + 1, 0x8000000000000ULL),	/* + indef 2008 qNaN */
+	DPCNST(0, DP_EMAX,     0xFFFFFFFFFFFFFULL),	/* + max */
+	DPCNST(1, DP_EMAX,     0xFFFFFFFFFFFFFULL),	/* - max */
+	DPCNST(0, DP_EMIN,     0x0000000000000ULL),	/* + min normal */
+	DPCNST(1, DP_EMIN,     0x0000000000000ULL),	/* - min normal */
+	DPCNST(0, DP_EMIN - 1, 0x0000000000001ULL),	/* + min denormal */
+	DPCNST(1, DP_EMIN - 1, 0x0000000000001ULL),	/* - min denormal */
+	DPCNST(0, 31,          0x0000000000000ULL),	/* + 1.0e31 */
+	DPCNST(0, 63,          0x0000000000000ULL),	/* + 1.0e63 */
+};
+
+#define SPCNST(s, b, m)							\
+	xPCNST(s, b, m, SP_EBIAS)
+
+const union ieee754sp __ieee754sp_spcvals[] = {
+	SPCNST(0, SP_EMIN - 1, 0x000000),	/* + zero   */
+	SPCNST(1, SP_EMIN - 1, 0x000000),	/* - zero   */
+	SPCNST(0, 0,	       0x000000),	/* + 1.0   */
+	SPCNST(1, 0,	       0x000000),	/* - 1.0   */
+	SPCNST(0, 3,	       0x200000),	/* + 10.0   */
+	SPCNST(1, 3,	       0x200000),	/* - 10.0   */
+	SPCNST(0, SP_EMAX + 1, 0x000000),	/* + infinity */
+	SPCNST(1, SP_EMAX + 1, 0x000000),	/* - infinity */
+	SPCNST(0, SP_EMAX + 1, 0x3FFFFF),	/* + indef legacy quiet NaN */
+	SPCNST(0, SP_EMAX + 1, 0x400000),	/* + indef 2008 quiet NaN */
+	SPCNST(0, SP_EMAX,     0x7FFFFF),	/* + max normal */
+	SPCNST(1, SP_EMAX,     0x7FFFFF),	/* - max normal */
+	SPCNST(0, SP_EMIN,     0x000000),	/* + min normal */
+	SPCNST(1, SP_EMIN,     0x000000),	/* - min normal */
+	SPCNST(0, SP_EMIN - 1, 0x000001),	/* + min denormal */
+	SPCNST(1, SP_EMIN - 1, 0x000001),	/* - min denormal */
+	SPCNST(0, 31,	       0x000000),	/* + 1.0e31 */
+	SPCNST(0, 63,	       0x000000),	/* + 1.0e63 */
+};
diff --git a/arch/mips/math-emu/ieee754.h b/arch/mips/math-emu/ieee754.h
new file mode 100644
index 000000000..090caa740
--- /dev/null
+++ b/arch/mips/math-emu/ieee754.h
@@ -0,0 +1,311 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ *
+ *  Nov 7, 2000
+ *  Modification to allow integration with Linux kernel
+ *
+ *  Kevin D. Kissell, kevink@mips.com and Carsten Langgard, carstenl@mips.com
+ *  Copyright (C) 2000 MIPS Technologies, Inc. All rights reserved.
+ */
+#ifndef __ARCH_MIPS_MATH_EMU_IEEE754_H
+#define __ARCH_MIPS_MATH_EMU_IEEE754_H
+
+#include <linux/compiler.h>
+#include <asm/byteorder.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/sched.h>
+#include <asm/bitfield.h>
+
+union ieee754dp {
+	struct {
+		__BITFIELD_FIELD(unsigned int sign:1,
+		__BITFIELD_FIELD(unsigned int bexp:11,
+		__BITFIELD_FIELD(u64 mant:52,
+		;)))
+	};
+	u64 bits;
+};
+
+union ieee754sp {
+	struct {
+		__BITFIELD_FIELD(unsigned sign:1,
+		__BITFIELD_FIELD(unsigned bexp:8,
+		__BITFIELD_FIELD(unsigned mant:23,
+		;)))
+	};
+	u32 bits;
+};
+
+/*
+ * single precision (often aka float)
+*/
+int ieee754sp_class(union ieee754sp x);
+
+union ieee754sp ieee754sp_abs(union ieee754sp x);
+union ieee754sp ieee754sp_neg(union ieee754sp x);
+
+union ieee754sp ieee754sp_add(union ieee754sp x, union ieee754sp y);
+union ieee754sp ieee754sp_sub(union ieee754sp x, union ieee754sp y);
+union ieee754sp ieee754sp_mul(union ieee754sp x, union ieee754sp y);
+union ieee754sp ieee754sp_div(union ieee754sp x, union ieee754sp y);
+
+union ieee754sp ieee754sp_fint(int x);
+union ieee754sp ieee754sp_flong(s64 x);
+union ieee754sp ieee754sp_fdp(union ieee754dp x);
+union ieee754sp ieee754sp_rint(union ieee754sp x);
+
+int ieee754sp_tint(union ieee754sp x);
+s64 ieee754sp_tlong(union ieee754sp x);
+
+int ieee754sp_cmp(union ieee754sp x, union ieee754sp y, int cop, int sig);
+
+union ieee754sp ieee754sp_sqrt(union ieee754sp x);
+
+union ieee754sp ieee754sp_maddf(union ieee754sp z, union ieee754sp x,
+				union ieee754sp y);
+union ieee754sp ieee754sp_msubf(union ieee754sp z, union ieee754sp x,
+				union ieee754sp y);
+union ieee754sp ieee754sp_madd(union ieee754sp z, union ieee754sp x,
+				union ieee754sp y);
+union ieee754sp ieee754sp_msub(union ieee754sp z, union ieee754sp x,
+				union ieee754sp y);
+union ieee754sp ieee754sp_nmadd(union ieee754sp z, union ieee754sp x,
+				union ieee754sp y);
+union ieee754sp ieee754sp_nmsub(union ieee754sp z, union ieee754sp x,
+				union ieee754sp y);
+int ieee754sp_2008class(union ieee754sp x);
+union ieee754sp ieee754sp_fmin(union ieee754sp x, union ieee754sp y);
+union ieee754sp ieee754sp_fmina(union ieee754sp x, union ieee754sp y);
+union ieee754sp ieee754sp_fmax(union ieee754sp x, union ieee754sp y);
+union ieee754sp ieee754sp_fmaxa(union ieee754sp x, union ieee754sp y);
+
+/*
+ * double precision (often aka double)
+*/
+int ieee754dp_class(union ieee754dp x);
+
+union ieee754dp ieee754dp_add(union ieee754dp x, union ieee754dp y);
+union ieee754dp ieee754dp_sub(union ieee754dp x, union ieee754dp y);
+union ieee754dp ieee754dp_mul(union ieee754dp x, union ieee754dp y);
+union ieee754dp ieee754dp_div(union ieee754dp x, union ieee754dp y);
+
+union ieee754dp ieee754dp_abs(union ieee754dp x);
+union ieee754dp ieee754dp_neg(union ieee754dp x);
+
+union ieee754dp ieee754dp_fint(int x);
+union ieee754dp ieee754dp_flong(s64 x);
+union ieee754dp ieee754dp_fsp(union ieee754sp x);
+union ieee754dp ieee754dp_rint(union ieee754dp x);
+
+int ieee754dp_tint(union ieee754dp x);
+s64 ieee754dp_tlong(union ieee754dp x);
+
+int ieee754dp_cmp(union ieee754dp x, union ieee754dp y, int cop, int sig);
+
+union ieee754dp ieee754dp_sqrt(union ieee754dp x);
+
+union ieee754dp ieee754dp_maddf(union ieee754dp z, union ieee754dp x,
+				union ieee754dp y);
+union ieee754dp ieee754dp_msubf(union ieee754dp z, union ieee754dp x,
+				union ieee754dp y);
+union ieee754dp ieee754dp_madd(union ieee754dp z, union ieee754dp x,
+				union ieee754dp y);
+union ieee754dp ieee754dp_msub(union ieee754dp z, union ieee754dp x,
+				union ieee754dp y);
+union ieee754dp ieee754dp_nmadd(union ieee754dp z, union ieee754dp x,
+				union ieee754dp y);
+union ieee754dp ieee754dp_nmsub(union ieee754dp z, union ieee754dp x,
+				union ieee754dp y);
+int ieee754dp_2008class(union ieee754dp x);
+union ieee754dp ieee754dp_fmin(union ieee754dp x, union ieee754dp y);
+union ieee754dp ieee754dp_fmina(union ieee754dp x, union ieee754dp y);
+union ieee754dp ieee754dp_fmax(union ieee754dp x, union ieee754dp y);
+union ieee754dp ieee754dp_fmaxa(union ieee754dp x, union ieee754dp y);
+
+
+/* 5 types of floating point number
+*/
+enum {
+	IEEE754_CLASS_NORM	= 0x00,
+	IEEE754_CLASS_ZERO	= 0x01,
+	IEEE754_CLASS_DNORM	= 0x02,
+	IEEE754_CLASS_INF	= 0x03,
+	IEEE754_CLASS_SNAN	= 0x04,
+	IEEE754_CLASS_QNAN	= 0x05,
+};
+
+/* exception numbers */
+#define IEEE754_INEXACT			0x01
+#define IEEE754_UNDERFLOW		0x02
+#define IEEE754_OVERFLOW		0x04
+#define IEEE754_ZERO_DIVIDE		0x08
+#define IEEE754_INVALID_OPERATION	0x10
+
+/* cmp operators
+*/
+#define IEEE754_CLT	0x01
+#define IEEE754_CEQ	0x02
+#define IEEE754_CGT	0x04
+#define IEEE754_CUN	0x08
+
+/*
+ * The control status register
+ */
+struct _ieee754_csr {
+	__BITFIELD_FIELD(unsigned fcc:7,	/* condition[7:1] */
+	__BITFIELD_FIELD(unsigned nod:1,	/* set 1 for no denormals */
+	__BITFIELD_FIELD(unsigned c:1,		/* condition[0] */
+	__BITFIELD_FIELD(unsigned pad0:3,
+	__BITFIELD_FIELD(unsigned abs2008:1,	/* IEEE 754-2008 ABS/NEG.fmt */
+	__BITFIELD_FIELD(unsigned nan2008:1,	/* IEEE 754-2008 NaN mode */
+	__BITFIELD_FIELD(unsigned cx:6,		/* exceptions this operation */
+	__BITFIELD_FIELD(unsigned mx:5,		/* exception enable  mask */
+	__BITFIELD_FIELD(unsigned sx:5,		/* exceptions total */
+	__BITFIELD_FIELD(unsigned rm:2,		/* current rounding mode */
+	;))))))))))
+};
+#define ieee754_csr (*(struct _ieee754_csr *)(&current->thread.fpu.fcr31))
+
+static inline unsigned int ieee754_getrm(void)
+{
+	return (ieee754_csr.rm);
+}
+
+static inline unsigned int ieee754_setrm(unsigned int rm)
+{
+	return (ieee754_csr.rm = rm);
+}
+
+/*
+ * get current exceptions
+ */
+static inline unsigned int ieee754_getcx(void)
+{
+	return (ieee754_csr.cx);
+}
+
+/* test for current exception condition
+ */
+static inline int ieee754_cxtest(unsigned int n)
+{
+	return (ieee754_csr.cx & n);
+}
+
+/*
+ * get sticky exceptions
+ */
+static inline unsigned int ieee754_getsx(void)
+{
+	return (ieee754_csr.sx);
+}
+
+/* clear sticky conditions
+*/
+static inline unsigned int ieee754_clrsx(void)
+{
+	return (ieee754_csr.sx = 0);
+}
+
+/* test for sticky exception condition
+ */
+static inline int ieee754_sxtest(unsigned int n)
+{
+	return (ieee754_csr.sx & n);
+}
+
+/* debugging */
+union ieee754sp ieee754sp_dump(char *s, union ieee754sp x);
+union ieee754dp ieee754dp_dump(char *s, union ieee754dp x);
+
+#define IEEE754_SPCVAL_PZERO		0	/* +0.0 */
+#define IEEE754_SPCVAL_NZERO		1	/* -0.0 */
+#define IEEE754_SPCVAL_PONE		2	/* +1.0 */
+#define IEEE754_SPCVAL_NONE		3	/* -1.0 */
+#define IEEE754_SPCVAL_PTEN		4	/* +10.0 */
+#define IEEE754_SPCVAL_NTEN		5	/* -10.0 */
+#define IEEE754_SPCVAL_PINFINITY	6	/* +inf */
+#define IEEE754_SPCVAL_NINFINITY	7	/* -inf */
+#define IEEE754_SPCVAL_INDEF_LEG	8	/* legacy quiet NaN */
+#define IEEE754_SPCVAL_INDEF_2008	9	/* IEEE 754-2008 quiet NaN */
+#define IEEE754_SPCVAL_PMAX		10	/* +max norm */
+#define IEEE754_SPCVAL_NMAX		11	/* -max norm */
+#define IEEE754_SPCVAL_PMIN		12	/* +min norm */
+#define IEEE754_SPCVAL_NMIN		13	/* -min norm */
+#define IEEE754_SPCVAL_PMIND		14	/* +min denorm */
+#define IEEE754_SPCVAL_NMIND		15	/* -min denorm */
+#define IEEE754_SPCVAL_P1E31		16	/* + 1.0e31 */
+#define IEEE754_SPCVAL_P1E63		17	/* + 1.0e63 */
+
+extern const union ieee754dp __ieee754dp_spcvals[];
+extern const union ieee754sp __ieee754sp_spcvals[];
+#define ieee754dp_spcvals ((const union ieee754dp *)__ieee754dp_spcvals)
+#define ieee754sp_spcvals ((const union ieee754sp *)__ieee754sp_spcvals)
+
+/*
+ * Return infinity with given sign
+ */
+#define ieee754dp_inf(sn)     (ieee754dp_spcvals[IEEE754_SPCVAL_PINFINITY+(sn)])
+#define ieee754dp_zero(sn)	(ieee754dp_spcvals[IEEE754_SPCVAL_PZERO+(sn)])
+#define ieee754dp_one(sn)	(ieee754dp_spcvals[IEEE754_SPCVAL_PONE+(sn)])
+#define ieee754dp_ten(sn)	(ieee754dp_spcvals[IEEE754_SPCVAL_PTEN+(sn)])
+#define ieee754dp_indef()	(ieee754dp_spcvals[IEEE754_SPCVAL_INDEF_LEG + \
+						   ieee754_csr.nan2008])
+#define ieee754dp_max(sn)	(ieee754dp_spcvals[IEEE754_SPCVAL_PMAX+(sn)])
+#define ieee754dp_min(sn)	(ieee754dp_spcvals[IEEE754_SPCVAL_PMIN+(sn)])
+#define ieee754dp_mind(sn)	(ieee754dp_spcvals[IEEE754_SPCVAL_PMIND+(sn)])
+#define ieee754dp_1e31()	(ieee754dp_spcvals[IEEE754_SPCVAL_P1E31])
+#define ieee754dp_1e63()	(ieee754dp_spcvals[IEEE754_SPCVAL_P1E63])
+
+#define ieee754sp_inf(sn)     (ieee754sp_spcvals[IEEE754_SPCVAL_PINFINITY+(sn)])
+#define ieee754sp_zero(sn)	(ieee754sp_spcvals[IEEE754_SPCVAL_PZERO+(sn)])
+#define ieee754sp_one(sn)	(ieee754sp_spcvals[IEEE754_SPCVAL_PONE+(sn)])
+#define ieee754sp_ten(sn)	(ieee754sp_spcvals[IEEE754_SPCVAL_PTEN+(sn)])
+#define ieee754sp_indef()	(ieee754sp_spcvals[IEEE754_SPCVAL_INDEF_LEG + \
+						   ieee754_csr.nan2008])
+#define ieee754sp_max(sn)	(ieee754sp_spcvals[IEEE754_SPCVAL_PMAX+(sn)])
+#define ieee754sp_min(sn)	(ieee754sp_spcvals[IEEE754_SPCVAL_PMIN+(sn)])
+#define ieee754sp_mind(sn)	(ieee754sp_spcvals[IEEE754_SPCVAL_PMIND+(sn)])
+#define ieee754sp_1e31()	(ieee754sp_spcvals[IEEE754_SPCVAL_P1E31])
+#define ieee754sp_1e63()	(ieee754sp_spcvals[IEEE754_SPCVAL_P1E63])
+
+/*
+ * Indefinite integer value
+ */
+static inline int ieee754si_indef(void)
+{
+	return ieee754_csr.nan2008 ? 0 : INT_MAX;
+}
+
+static inline s64 ieee754di_indef(void)
+{
+	return ieee754_csr.nan2008 ? 0 : S64_MAX;
+}
+
+/*
+ * Overflow integer value
+ */
+static inline int ieee754si_overflow(int xs)
+{
+	return ieee754_csr.nan2008 && xs ? INT_MIN : INT_MAX;
+}
+
+static inline s64 ieee754di_overflow(int xs)
+{
+	return ieee754_csr.nan2008 && xs ? S64_MIN : S64_MAX;
+}
+
+/* result types for xctx.rt */
+#define IEEE754_RT_SP	0
+#define IEEE754_RT_DP	1
+#define IEEE754_RT_XP	2
+#define IEEE754_RT_SI	3
+#define IEEE754_RT_DI	4
+
+/* compat */
+#define ieee754dp_fix(x)	ieee754dp_tint(x)
+#define ieee754sp_fix(x)	ieee754sp_tint(x)
+
+#endif /* __ARCH_MIPS_MATH_EMU_IEEE754_H */
diff --git a/arch/mips/math-emu/ieee754d.c b/arch/mips/math-emu/ieee754d.c
new file mode 100644
index 000000000..586c4db2d
--- /dev/null
+++ b/arch/mips/math-emu/ieee754d.c
@@ -0,0 +1,99 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Some debug functions
+ *
+ * MIPS floating point support
+ *
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ *
+ *  Nov 7, 2000
+ *  Modified to build and operate in Linux kernel environment.
+ *
+ *  Kevin D. Kissell, kevink@mips.com and Carsten Langgaard, carstenl@mips.com
+ *  Copyright (C) 2000 MIPS Technologies, Inc. All rights reserved.
+ */
+
+#include <linux/types.h>
+#include <linux/printk.h>
+#include "ieee754.h"
+#include "ieee754sp.h"
+#include "ieee754dp.h"
+
+union ieee754dp ieee754dp_dump(char *m, union ieee754dp x)
+{
+	int i;
+
+	printk("%s", m);
+	printk("<%08x,%08x>\n", (unsigned) (x.bits >> 32),
+	       (unsigned) x.bits);
+	printk("\t=");
+	switch (ieee754dp_class(x)) {
+	case IEEE754_CLASS_QNAN:
+	case IEEE754_CLASS_SNAN:
+		printk("Nan %c", DPSIGN(x) ? '-' : '+');
+		for (i = DP_FBITS - 1; i >= 0; i--)
+			printk("%c", DPMANT(x) & DP_MBIT(i) ? '1' : '0');
+		break;
+	case IEEE754_CLASS_INF:
+		printk("%cInfinity", DPSIGN(x) ? '-' : '+');
+		break;
+	case IEEE754_CLASS_ZERO:
+		printk("%cZero", DPSIGN(x) ? '-' : '+');
+		break;
+	case IEEE754_CLASS_DNORM:
+		printk("%c0.", DPSIGN(x) ? '-' : '+');
+		for (i = DP_FBITS - 1; i >= 0; i--)
+			printk("%c", DPMANT(x) & DP_MBIT(i) ? '1' : '0');
+		printk("e%d", DPBEXP(x) - DP_EBIAS);
+		break;
+	case IEEE754_CLASS_NORM:
+		printk("%c1.", DPSIGN(x) ? '-' : '+');
+		for (i = DP_FBITS - 1; i >= 0; i--)
+			printk("%c", DPMANT(x) & DP_MBIT(i) ? '1' : '0');
+		printk("e%d", DPBEXP(x) - DP_EBIAS);
+		break;
+	default:
+		printk("Illegal/Unknown IEEE754 value class");
+	}
+	printk("\n");
+	return x;
+}
+
+union ieee754sp ieee754sp_dump(char *m, union ieee754sp x)
+{
+	int i;
+
+	printk("%s=", m);
+	printk("<%08x>\n", (unsigned) x.bits);
+	printk("\t=");
+	switch (ieee754sp_class(x)) {
+	case IEEE754_CLASS_QNAN:
+	case IEEE754_CLASS_SNAN:
+		printk("Nan %c", SPSIGN(x) ? '-' : '+');
+		for (i = SP_FBITS - 1; i >= 0; i--)
+			printk("%c", SPMANT(x) & SP_MBIT(i) ? '1' : '0');
+		break;
+	case IEEE754_CLASS_INF:
+		printk("%cInfinity", SPSIGN(x) ? '-' : '+');
+		break;
+	case IEEE754_CLASS_ZERO:
+		printk("%cZero", SPSIGN(x) ? '-' : '+');
+		break;
+	case IEEE754_CLASS_DNORM:
+		printk("%c0.", SPSIGN(x) ? '-' : '+');
+		for (i = SP_FBITS - 1; i >= 0; i--)
+			printk("%c", SPMANT(x) & SP_MBIT(i) ? '1' : '0');
+		printk("e%d", SPBEXP(x) - SP_EBIAS);
+		break;
+	case IEEE754_CLASS_NORM:
+		printk("%c1.", SPSIGN(x) ? '-' : '+');
+		for (i = SP_FBITS - 1; i >= 0; i--)
+			printk("%c", SPMANT(x) & SP_MBIT(i) ? '1' : '0');
+		printk("e%d", SPBEXP(x) - SP_EBIAS);
+		break;
+	default:
+		printk("Illegal/Unknown IEEE754 value class");
+	}
+	printk("\n");
+	return x;
+}
diff --git a/arch/mips/math-emu/ieee754dp.c b/arch/mips/math-emu/ieee754dp.c
new file mode 100644
index 000000000..07ef146e2
--- /dev/null
+++ b/arch/mips/math-emu/ieee754dp.c
@@ -0,0 +1,197 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* IEEE754 floating point arithmetic
+ * double precision: common utilities
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ */
+
+#include <linux/compiler.h>
+
+#include "ieee754dp.h"
+
+int ieee754dp_class(union ieee754dp x)
+{
+	COMPXDP;
+	EXPLODEXDP;
+	return xc;
+}
+
+static inline int ieee754dp_isnan(union ieee754dp x)
+{
+	return ieee754_class_nan(ieee754dp_class(x));
+}
+
+static inline int ieee754dp_issnan(union ieee754dp x)
+{
+	int qbit;
+
+	assert(ieee754dp_isnan(x));
+	qbit = (DPMANT(x) & DP_MBIT(DP_FBITS - 1)) == DP_MBIT(DP_FBITS - 1);
+	return ieee754_csr.nan2008 ^ qbit;
+}
+
+
+/*
+ * Raise the Invalid Operation IEEE 754 exception
+ * and convert the signaling NaN supplied to a quiet NaN.
+ */
+union ieee754dp __cold ieee754dp_nanxcpt(union ieee754dp r)
+{
+	assert(ieee754dp_issnan(r));
+
+	ieee754_setcx(IEEE754_INVALID_OPERATION);
+	if (ieee754_csr.nan2008) {
+		DPMANT(r) |= DP_MBIT(DP_FBITS - 1);
+	} else {
+		DPMANT(r) &= ~DP_MBIT(DP_FBITS - 1);
+		if (!ieee754dp_isnan(r))
+			DPMANT(r) |= DP_MBIT(DP_FBITS - 2);
+	}
+
+	return r;
+}
+
+static u64 ieee754dp_get_rounding(int sn, u64 xm)
+{
+	/* inexact must round of 3 bits
+	 */
+	if (xm & (DP_MBIT(3) - 1)) {
+		switch (ieee754_csr.rm) {
+		case FPU_CSR_RZ:
+			break;
+		case FPU_CSR_RN:
+			xm += 0x3 + ((xm >> 3) & 1);
+			/* xm += (xm&0x8)?0x4:0x3 */
+			break;
+		case FPU_CSR_RU:	/* toward +Infinity */
+			if (!sn)	/* ?? */
+				xm += 0x8;
+			break;
+		case FPU_CSR_RD:	/* toward -Infinity */
+			if (sn) /* ?? */
+				xm += 0x8;
+			break;
+		}
+	}
+	return xm;
+}
+
+
+/* generate a normal/denormal number with over,under handling
+ * sn is sign
+ * xe is an unbiased exponent
+ * xm is 3bit extended precision value.
+ */
+union ieee754dp ieee754dp_format(int sn, int xe, u64 xm)
+{
+	assert(xm);		/* we don't gen exact zeros (probably should) */
+
+	assert((xm >> (DP_FBITS + 1 + 3)) == 0);	/* no excess */
+	assert(xm & (DP_HIDDEN_BIT << 3));
+
+	if (xe < DP_EMIN) {
+		/* strip lower bits */
+		int es = DP_EMIN - xe;
+
+		if (ieee754_csr.nod) {
+			ieee754_setcx(IEEE754_UNDERFLOW);
+			ieee754_setcx(IEEE754_INEXACT);
+
+			switch(ieee754_csr.rm) {
+			case FPU_CSR_RN:
+			case FPU_CSR_RZ:
+				return ieee754dp_zero(sn);
+			case FPU_CSR_RU:    /* toward +Infinity */
+				if (sn == 0)
+					return ieee754dp_min(0);
+				else
+					return ieee754dp_zero(1);
+			case FPU_CSR_RD:    /* toward -Infinity */
+				if (sn == 0)
+					return ieee754dp_zero(0);
+				else
+					return ieee754dp_min(1);
+			}
+		}
+
+		if (xe == DP_EMIN - 1 &&
+		    ieee754dp_get_rounding(sn, xm) >> (DP_FBITS + 1 + 3))
+		{
+			/* Not tiny after rounding */
+			ieee754_setcx(IEEE754_INEXACT);
+			xm = ieee754dp_get_rounding(sn, xm);
+			xm >>= 1;
+			/* Clear grs bits */
+			xm &= ~(DP_MBIT(3) - 1);
+			xe++;
+		}
+		else {
+			/* sticky right shift es bits
+			 */
+			xm = XDPSRS(xm, es);
+			xe += es;
+			assert((xm & (DP_HIDDEN_BIT << 3)) == 0);
+			assert(xe == DP_EMIN);
+		}
+	}
+	if (xm & (DP_MBIT(3) - 1)) {
+		ieee754_setcx(IEEE754_INEXACT);
+		if ((xm & (DP_HIDDEN_BIT << 3)) == 0) {
+			ieee754_setcx(IEEE754_UNDERFLOW);
+		}
+
+		/* inexact must round of 3 bits
+		 */
+		xm = ieee754dp_get_rounding(sn, xm);
+		/* adjust exponent for rounding add overflowing
+		 */
+		if (xm >> (DP_FBITS + 3 + 1)) {
+			/* add causes mantissa overflow */
+			xm >>= 1;
+			xe++;
+		}
+	}
+	/* strip grs bits */
+	xm >>= 3;
+
+	assert((xm >> (DP_FBITS + 1)) == 0);	/* no excess */
+	assert(xe >= DP_EMIN);
+
+	if (xe > DP_EMAX) {
+		ieee754_setcx(IEEE754_OVERFLOW);
+		ieee754_setcx(IEEE754_INEXACT);
+		/* -O can be table indexed by (rm,sn) */
+		switch (ieee754_csr.rm) {
+		case FPU_CSR_RN:
+			return ieee754dp_inf(sn);
+		case FPU_CSR_RZ:
+			return ieee754dp_max(sn);
+		case FPU_CSR_RU:	/* toward +Infinity */
+			if (sn == 0)
+				return ieee754dp_inf(0);
+			else
+				return ieee754dp_max(1);
+		case FPU_CSR_RD:	/* toward -Infinity */
+			if (sn == 0)
+				return ieee754dp_max(0);
+			else
+				return ieee754dp_inf(1);
+		}
+	}
+	/* gen norm/denorm/zero */
+
+	if ((xm & DP_HIDDEN_BIT) == 0) {
+		/* we underflow (tiny/zero) */
+		assert(xe == DP_EMIN);
+		if (ieee754_csr.mx & IEEE754_UNDERFLOW)
+			ieee754_setcx(IEEE754_UNDERFLOW);
+		return builddp(sn, DP_EMIN - 1 + DP_EBIAS, xm);
+	} else {
+		assert((xm >> (DP_FBITS + 1)) == 0);	/* no excess */
+		assert(xm & DP_HIDDEN_BIT);
+
+		return builddp(sn, xe + DP_EBIAS, xm & ~DP_HIDDEN_BIT);
+	}
+}
diff --git a/arch/mips/math-emu/ieee754dp.h b/arch/mips/math-emu/ieee754dp.h
new file mode 100644
index 000000000..b7c43a99a
--- /dev/null
+++ b/arch/mips/math-emu/ieee754dp.h
@@ -0,0 +1,73 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * IEEE754 floating point
+ * double precision internal header file
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ */
+
+#include <linux/compiler.h>
+
+#include "ieee754int.h"
+
+#define assert(expr) ((void)0)
+
+#define DP_EBIAS	1023
+#define DP_EMIN		(-1022)
+#define DP_EMAX		1023
+#define DP_FBITS	52
+#define DP_MBITS	52
+
+#define DP_MBIT(x)	((u64)1 << (x))
+#define DP_HIDDEN_BIT	DP_MBIT(DP_FBITS)
+#define DP_SIGN_BIT	DP_MBIT(63)
+
+#define DPSIGN(dp)	(dp.sign)
+#define DPBEXP(dp)	(dp.bexp)
+#define DPMANT(dp)	(dp.mant)
+
+static inline int ieee754dp_finite(union ieee754dp x)
+{
+	return DPBEXP(x) != DP_EMAX + 1 + DP_EBIAS;
+}
+
+/* 3bit extended double precision sticky right shift */
+#define XDPSRS(v,rs)	\
+	((rs > (DP_FBITS+3))?1:((v) >> (rs)) | ((v) << (64-(rs)) != 0))
+
+#define XDPSRSX1() \
+	(xe++, (xm = (xm >> 1) | (xm & 1)))
+
+#define XDPSRS1(v)	\
+	(((v) >> 1) | ((v) & 1))
+
+/* 32bit * 32bit => 64bit unsigned integer multiplication */
+#define DPXMULT(x, y)	((u64)(x) * (u64)y)
+
+/* convert denormal to normalized with extended exponent */
+#define DPDNORMx(m,e) \
+	while ((m >> DP_FBITS) == 0) { m <<= 1; e--; }
+#define DPDNORMX	DPDNORMx(xm, xe)
+#define DPDNORMY	DPDNORMx(ym, ye)
+#define DPDNORMZ	DPDNORMx(zm, ze)
+
+static inline union ieee754dp builddp(int s, int bx, u64 m)
+{
+	union ieee754dp r;
+
+	assert((s) == 0 || (s) == 1);
+	assert((bx) >= DP_EMIN - 1 + DP_EBIAS
+	       && (bx) <= DP_EMAX + 1 + DP_EBIAS);
+	assert(((m) >> DP_FBITS) == 0);
+
+	r.sign = s;
+	r.bexp = bx;
+	r.mant = m;
+
+	return r;
+}
+
+extern union ieee754dp __cold ieee754dp_nanxcpt(union ieee754dp);
+extern union ieee754dp ieee754dp_format(int, int, u64);
diff --git a/arch/mips/math-emu/ieee754int.h b/arch/mips/math-emu/ieee754int.h
new file mode 100644
index 000000000..2c3b13546
--- /dev/null
+++ b/arch/mips/math-emu/ieee754int.h
@@ -0,0 +1,149 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * IEEE754 floating point
+ * common internal header file
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ */
+#ifndef __IEEE754INT_H
+#define __IEEE754INT_H
+
+#include "ieee754.h"
+
+#define CLPAIR(x, y)	((x)*6+(y))
+
+enum maddf_flags {
+	MADDF_NEGATE_PRODUCT	= 1 << 0,
+	MADDF_NEGATE_ADDITION	= 1 << 1,
+};
+
+static inline void ieee754_clearcx(void)
+{
+	ieee754_csr.cx = 0;
+}
+
+static inline void ieee754_setcx(const unsigned int flags)
+{
+	ieee754_csr.cx |= flags;
+	ieee754_csr.sx |= flags;
+}
+
+static inline int ieee754_setandtestcx(const unsigned int x)
+{
+	ieee754_setcx(x);
+
+	return ieee754_csr.mx & x;
+}
+
+static inline int ieee754_class_nan(int xc)
+{
+	return xc >= IEEE754_CLASS_SNAN;
+}
+
+#define COMPXSP \
+	unsigned int xm; int xe; int xs __maybe_unused; int xc
+
+#define COMPYSP \
+	unsigned int ym; int ye; int ys; int yc
+
+#define COMPZSP \
+	unsigned int zm; int ze; int zs; int zc
+
+#define EXPLODESP(v, vc, vs, ve, vm)					\
+{									\
+	vs = SPSIGN(v);							\
+	ve = SPBEXP(v);							\
+	vm = SPMANT(v);							\
+	if (ve == SP_EMAX+1+SP_EBIAS) {					\
+		if (vm == 0)						\
+			vc = IEEE754_CLASS_INF;				\
+		else if (ieee754_csr.nan2008 ^ !(vm & SP_MBIT(SP_FBITS - 1))) \
+			vc = IEEE754_CLASS_QNAN;			\
+		else							\
+			vc = IEEE754_CLASS_SNAN;			\
+	} else if (ve == SP_EMIN-1+SP_EBIAS) {				\
+		if (vm) {						\
+			ve = SP_EMIN;					\
+			vc = IEEE754_CLASS_DNORM;			\
+		} else							\
+			vc = IEEE754_CLASS_ZERO;			\
+	} else {							\
+		ve -= SP_EBIAS;						\
+		vm |= SP_HIDDEN_BIT;					\
+		vc = IEEE754_CLASS_NORM;				\
+	}								\
+}
+#define EXPLODEXSP EXPLODESP(x, xc, xs, xe, xm)
+#define EXPLODEYSP EXPLODESP(y, yc, ys, ye, ym)
+#define EXPLODEZSP EXPLODESP(z, zc, zs, ze, zm)
+
+
+#define COMPXDP \
+	u64 xm; int xe; int xs __maybe_unused; int xc
+
+#define COMPYDP \
+	u64 ym; int ye; int ys; int yc
+
+#define COMPZDP \
+	u64 zm; int ze; int zs; int zc
+
+#define EXPLODEDP(v, vc, vs, ve, vm)					\
+{									\
+	vm = DPMANT(v);							\
+	vs = DPSIGN(v);							\
+	ve = DPBEXP(v);							\
+	if (ve == DP_EMAX+1+DP_EBIAS) {					\
+		if (vm == 0)						\
+			vc = IEEE754_CLASS_INF;				\
+		else if (ieee754_csr.nan2008 ^ !(vm & DP_MBIT(DP_FBITS - 1))) \
+			vc = IEEE754_CLASS_QNAN;			\
+		else							\
+			vc = IEEE754_CLASS_SNAN;			\
+	} else if (ve == DP_EMIN-1+DP_EBIAS) {				\
+		if (vm) {						\
+			ve = DP_EMIN;					\
+			vc = IEEE754_CLASS_DNORM;			\
+		} else							\
+			vc = IEEE754_CLASS_ZERO;			\
+	} else {							\
+		ve -= DP_EBIAS;						\
+		vm |= DP_HIDDEN_BIT;					\
+		vc = IEEE754_CLASS_NORM;				\
+	}								\
+}
+#define EXPLODEXDP EXPLODEDP(x, xc, xs, xe, xm)
+#define EXPLODEYDP EXPLODEDP(y, yc, ys, ye, ym)
+#define EXPLODEZDP EXPLODEDP(z, zc, zs, ze, zm)
+
+#define FLUSHDP(v, vc, vs, ve, vm)					\
+	if (vc==IEEE754_CLASS_DNORM) {					\
+		if (ieee754_csr.nod) {					\
+			ieee754_setcx(IEEE754_INEXACT);			\
+			vc = IEEE754_CLASS_ZERO;			\
+			ve = DP_EMIN-1+DP_EBIAS;			\
+			vm = 0;						\
+			v = ieee754dp_zero(vs);				\
+		}							\
+	}
+
+#define FLUSHSP(v, vc, vs, ve, vm)					\
+	if (vc==IEEE754_CLASS_DNORM) {					\
+		if (ieee754_csr.nod) {					\
+			ieee754_setcx(IEEE754_INEXACT);			\
+			vc = IEEE754_CLASS_ZERO;			\
+			ve = SP_EMIN-1+SP_EBIAS;			\
+			vm = 0;						\
+			v = ieee754sp_zero(vs);				\
+		}							\
+	}
+
+#define FLUSHXDP FLUSHDP(x, xc, xs, xe, xm)
+#define FLUSHYDP FLUSHDP(y, yc, ys, ye, ym)
+#define FLUSHZDP FLUSHDP(z, zc, zs, ze, zm)
+#define FLUSHXSP FLUSHSP(x, xc, xs, xe, xm)
+#define FLUSHYSP FLUSHSP(y, yc, ys, ye, ym)
+#define FLUSHZSP FLUSHSP(z, zc, zs, ze, zm)
+
+#endif /* __IEEE754INT_H  */
diff --git a/arch/mips/math-emu/ieee754sp.c b/arch/mips/math-emu/ieee754sp.c
new file mode 100644
index 000000000..0b6267bc8
--- /dev/null
+++ b/arch/mips/math-emu/ieee754sp.c
@@ -0,0 +1,196 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* IEEE754 floating point arithmetic
+ * single precision
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ */
+
+#include <linux/compiler.h>
+
+#include "ieee754sp.h"
+
+int ieee754sp_class(union ieee754sp x)
+{
+	COMPXSP;
+	EXPLODEXSP;
+	return xc;
+}
+
+static inline int ieee754sp_isnan(union ieee754sp x)
+{
+	return ieee754_class_nan(ieee754sp_class(x));
+}
+
+static inline int ieee754sp_issnan(union ieee754sp x)
+{
+	int qbit;
+
+	assert(ieee754sp_isnan(x));
+	qbit = (SPMANT(x) & SP_MBIT(SP_FBITS - 1)) == SP_MBIT(SP_FBITS - 1);
+	return ieee754_csr.nan2008 ^ qbit;
+}
+
+
+/*
+ * Raise the Invalid Operation IEEE 754 exception
+ * and convert the signaling NaN supplied to a quiet NaN.
+ */
+union ieee754sp __cold ieee754sp_nanxcpt(union ieee754sp r)
+{
+	assert(ieee754sp_issnan(r));
+
+	ieee754_setcx(IEEE754_INVALID_OPERATION);
+	if (ieee754_csr.nan2008) {
+		SPMANT(r) |= SP_MBIT(SP_FBITS - 1);
+	} else {
+		SPMANT(r) &= ~SP_MBIT(SP_FBITS - 1);
+		if (!ieee754sp_isnan(r))
+			SPMANT(r) |= SP_MBIT(SP_FBITS - 2);
+	}
+
+	return r;
+}
+
+static unsigned int ieee754sp_get_rounding(int sn, unsigned int xm)
+{
+	/* inexact must round of 3 bits
+	 */
+	if (xm & (SP_MBIT(3) - 1)) {
+		switch (ieee754_csr.rm) {
+		case FPU_CSR_RZ:
+			break;
+		case FPU_CSR_RN:
+			xm += 0x3 + ((xm >> 3) & 1);
+			/* xm += (xm&0x8)?0x4:0x3 */
+			break;
+		case FPU_CSR_RU:	/* toward +Infinity */
+			if (!sn)	/* ?? */
+				xm += 0x8;
+			break;
+		case FPU_CSR_RD:	/* toward -Infinity */
+			if (sn) /* ?? */
+				xm += 0x8;
+			break;
+		}
+	}
+	return xm;
+}
+
+
+/* generate a normal/denormal number with over,under handling
+ * sn is sign
+ * xe is an unbiased exponent
+ * xm is 3bit extended precision value.
+ */
+union ieee754sp ieee754sp_format(int sn, int xe, unsigned int xm)
+{
+	assert(xm);		/* we don't gen exact zeros (probably should) */
+
+	assert((xm >> (SP_FBITS + 1 + 3)) == 0);	/* no excess */
+	assert(xm & (SP_HIDDEN_BIT << 3));
+
+	if (xe < SP_EMIN) {
+		/* strip lower bits */
+		int es = SP_EMIN - xe;
+
+		if (ieee754_csr.nod) {
+			ieee754_setcx(IEEE754_UNDERFLOW);
+			ieee754_setcx(IEEE754_INEXACT);
+
+			switch(ieee754_csr.rm) {
+			case FPU_CSR_RN:
+			case FPU_CSR_RZ:
+				return ieee754sp_zero(sn);
+			case FPU_CSR_RU:      /* toward +Infinity */
+				if (sn == 0)
+					return ieee754sp_min(0);
+				else
+					return ieee754sp_zero(1);
+			case FPU_CSR_RD:      /* toward -Infinity */
+				if (sn == 0)
+					return ieee754sp_zero(0);
+				else
+					return ieee754sp_min(1);
+			}
+		}
+
+		if (xe == SP_EMIN - 1 &&
+		    ieee754sp_get_rounding(sn, xm) >> (SP_FBITS + 1 + 3))
+		{
+			/* Not tiny after rounding */
+			ieee754_setcx(IEEE754_INEXACT);
+			xm = ieee754sp_get_rounding(sn, xm);
+			xm >>= 1;
+			/* Clear grs bits */
+			xm &= ~(SP_MBIT(3) - 1);
+			xe++;
+		} else {
+			/* sticky right shift es bits
+			 */
+			xm = XSPSRS(xm, es);
+			xe += es;
+			assert((xm & (SP_HIDDEN_BIT << 3)) == 0);
+			assert(xe == SP_EMIN);
+		}
+	}
+	if (xm & (SP_MBIT(3) - 1)) {
+		ieee754_setcx(IEEE754_INEXACT);
+		if ((xm & (SP_HIDDEN_BIT << 3)) == 0) {
+			ieee754_setcx(IEEE754_UNDERFLOW);
+		}
+
+		/* inexact must round of 3 bits
+		 */
+		xm = ieee754sp_get_rounding(sn, xm);
+		/* adjust exponent for rounding add overflowing
+		 */
+		if (xm >> (SP_FBITS + 1 + 3)) {
+			/* add causes mantissa overflow */
+			xm >>= 1;
+			xe++;
+		}
+	}
+	/* strip grs bits */
+	xm >>= 3;
+
+	assert((xm >> (SP_FBITS + 1)) == 0);	/* no excess */
+	assert(xe >= SP_EMIN);
+
+	if (xe > SP_EMAX) {
+		ieee754_setcx(IEEE754_OVERFLOW);
+		ieee754_setcx(IEEE754_INEXACT);
+		/* -O can be table indexed by (rm,sn) */
+		switch (ieee754_csr.rm) {
+		case FPU_CSR_RN:
+			return ieee754sp_inf(sn);
+		case FPU_CSR_RZ:
+			return ieee754sp_max(sn);
+		case FPU_CSR_RU:	/* toward +Infinity */
+			if (sn == 0)
+				return ieee754sp_inf(0);
+			else
+				return ieee754sp_max(1);
+		case FPU_CSR_RD:	/* toward -Infinity */
+			if (sn == 0)
+				return ieee754sp_max(0);
+			else
+				return ieee754sp_inf(1);
+		}
+	}
+	/* gen norm/denorm/zero */
+
+	if ((xm & SP_HIDDEN_BIT) == 0) {
+		/* we underflow (tiny/zero) */
+		assert(xe == SP_EMIN);
+		if (ieee754_csr.mx & IEEE754_UNDERFLOW)
+			ieee754_setcx(IEEE754_UNDERFLOW);
+		return buildsp(sn, SP_EMIN - 1 + SP_EBIAS, xm);
+	} else {
+		assert((xm >> (SP_FBITS + 1)) == 0);	/* no excess */
+		assert(xm & SP_HIDDEN_BIT);
+
+		return buildsp(sn, xe + SP_EBIAS, xm & ~SP_HIDDEN_BIT);
+	}
+}
diff --git a/arch/mips/math-emu/ieee754sp.h b/arch/mips/math-emu/ieee754sp.h
new file mode 100644
index 000000000..79040f890
--- /dev/null
+++ b/arch/mips/math-emu/ieee754sp.h
@@ -0,0 +1,77 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * IEEE754 floating point
+ * double precision internal header file
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ */
+
+#include <linux/compiler.h>
+
+#include "ieee754int.h"
+
+#define assert(expr) ((void)0)
+
+#define SP_EBIAS	127
+#define SP_EMIN		(-126)
+#define SP_EMAX		127
+#define SP_FBITS	23
+#define SP_MBITS	23
+
+#define SP_MBIT(x)	((u32)1 << (x))
+#define SP_HIDDEN_BIT	SP_MBIT(SP_FBITS)
+#define SP_SIGN_BIT	SP_MBIT(31)
+
+#define SPSIGN(sp)	(sp.sign)
+#define SPBEXP(sp)	(sp.bexp)
+#define SPMANT(sp)	(sp.mant)
+
+static inline int ieee754sp_finite(union ieee754sp x)
+{
+	return SPBEXP(x) != SP_EMAX + 1 + SP_EBIAS;
+}
+
+/* 64 bit right shift with rounding */
+#define XSPSRS64(v, rs)						\
+	(((rs) >= 64) ? ((v) != 0) : ((v) >> (rs)) | ((v) << (64-(rs)) != 0))
+
+/* 3bit extended single precision sticky right shift */
+#define XSPSRS(v, rs)						\
+	((rs > (SP_FBITS+3))?1:((v) >> (rs)) | ((v) << (32-(rs)) != 0))
+
+#define XSPSRS1(m) \
+	((m >> 1) | (m & 1))
+
+#define SPXSRSX1() \
+	(xe++, (xm = XSPSRS1(xm)))
+
+#define SPXSRSY1() \
+	(ye++, (ym = XSPSRS1(ym)))
+
+/* convert denormal to normalized with extended exponent */
+#define SPDNORMx(m,e) \
+	while ((m >> SP_FBITS) == 0) { m <<= 1; e--; }
+#define SPDNORMX	SPDNORMx(xm, xe)
+#define SPDNORMY	SPDNORMx(ym, ye)
+#define SPDNORMZ	SPDNORMx(zm, ze)
+
+static inline union ieee754sp buildsp(int s, int bx, unsigned int m)
+{
+	union ieee754sp r;
+
+	assert((s) == 0 || (s) == 1);
+	assert((bx) >= SP_EMIN - 1 + SP_EBIAS
+	       && (bx) <= SP_EMAX + 1 + SP_EBIAS);
+	assert(((m) >> SP_FBITS) == 0);
+
+	r.sign = s;
+	r.bexp = bx;
+	r.mant = m;
+
+	return r;
+}
+
+extern union ieee754sp __cold ieee754sp_nanxcpt(union ieee754sp);
+extern union ieee754sp ieee754sp_format(int, int, unsigned);
diff --git a/arch/mips/math-emu/me-debugfs.c b/arch/mips/math-emu/me-debugfs.c
new file mode 100644
index 000000000..d5ad76b2b
--- /dev/null
+++ b/arch/mips/math-emu/me-debugfs.c
@@ -0,0 +1,353 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/cpumask.h>
+#include <linux/debugfs.h>
+#include <linux/fs.h>
+#include <linux/init.h>
+#include <linux/percpu.h>
+#include <linux/types.h>
+#include <asm/debug.h>
+#include <asm/fpu_emulator.h>
+#include <asm/local.h>
+
+DEFINE_PER_CPU(struct mips_fpu_emulator_stats, fpuemustats);
+
+static int fpuemu_stat_get(void *data, u64 *val)
+{
+	int cpu;
+	unsigned long sum = 0;
+
+	for_each_online_cpu(cpu) {
+		struct mips_fpu_emulator_stats *ps;
+		local_t *pv;
+
+		ps = &per_cpu(fpuemustats, cpu);
+		pv = (void *)ps + (unsigned long)data;
+		sum += local_read(pv);
+	}
+	*val = sum;
+	return 0;
+}
+DEFINE_SIMPLE_ATTRIBUTE(fops_fpuemu_stat, fpuemu_stat_get, NULL, "%llu\n");
+
+/*
+ * Used to obtain names for a debugfs instruction counter, given field name
+ * in fpuemustats structure. For example, for input "cmp_sueq_d", the output
+ * would be "cmp.sueq.d". This is needed since dots are not allowed to be
+ * used in structure field names, and are, on the other hand, desired to be
+ * used in debugfs item names to be clearly associated to corresponding
+ * MIPS FPU instructions.
+ */
+static void adjust_instruction_counter_name(char *out_name, char *in_name)
+{
+	int i = 0;
+
+	strcpy(out_name, in_name);
+	while (in_name[i] != '\0') {
+		if (out_name[i] == '_')
+			out_name[i] = '.';
+		i++;
+	}
+}
+
+static int fpuemustats_clear_show(struct seq_file *s, void *unused)
+{
+	__this_cpu_write((fpuemustats).emulated, 0);
+	__this_cpu_write((fpuemustats).loads, 0);
+	__this_cpu_write((fpuemustats).stores, 0);
+	__this_cpu_write((fpuemustats).branches, 0);
+	__this_cpu_write((fpuemustats).cp1ops, 0);
+	__this_cpu_write((fpuemustats).cp1xops, 0);
+	__this_cpu_write((fpuemustats).errors, 0);
+	__this_cpu_write((fpuemustats).ieee754_inexact, 0);
+	__this_cpu_write((fpuemustats).ieee754_underflow, 0);
+	__this_cpu_write((fpuemustats).ieee754_overflow, 0);
+	__this_cpu_write((fpuemustats).ieee754_zerodiv, 0);
+	__this_cpu_write((fpuemustats).ieee754_invalidop, 0);
+	__this_cpu_write((fpuemustats).ds_emul, 0);
+
+	__this_cpu_write((fpuemustats).abs_s, 0);
+	__this_cpu_write((fpuemustats).abs_d, 0);
+	__this_cpu_write((fpuemustats).add_s, 0);
+	__this_cpu_write((fpuemustats).add_d, 0);
+	__this_cpu_write((fpuemustats).bc1eqz, 0);
+	__this_cpu_write((fpuemustats).bc1nez, 0);
+	__this_cpu_write((fpuemustats).ceil_w_s, 0);
+	__this_cpu_write((fpuemustats).ceil_w_d, 0);
+	__this_cpu_write((fpuemustats).ceil_l_s, 0);
+	__this_cpu_write((fpuemustats).ceil_l_d, 0);
+	__this_cpu_write((fpuemustats).class_s, 0);
+	__this_cpu_write((fpuemustats).class_d, 0);
+	__this_cpu_write((fpuemustats).cmp_af_s, 0);
+	__this_cpu_write((fpuemustats).cmp_af_d, 0);
+	__this_cpu_write((fpuemustats).cmp_eq_s, 0);
+	__this_cpu_write((fpuemustats).cmp_eq_d, 0);
+	__this_cpu_write((fpuemustats).cmp_le_s, 0);
+	__this_cpu_write((fpuemustats).cmp_le_d, 0);
+	__this_cpu_write((fpuemustats).cmp_lt_s, 0);
+	__this_cpu_write((fpuemustats).cmp_lt_d, 0);
+	__this_cpu_write((fpuemustats).cmp_ne_s, 0);
+	__this_cpu_write((fpuemustats).cmp_ne_d, 0);
+	__this_cpu_write((fpuemustats).cmp_or_s, 0);
+	__this_cpu_write((fpuemustats).cmp_or_d, 0);
+	__this_cpu_write((fpuemustats).cmp_ueq_s, 0);
+	__this_cpu_write((fpuemustats).cmp_ueq_d, 0);
+	__this_cpu_write((fpuemustats).cmp_ule_s, 0);
+	__this_cpu_write((fpuemustats).cmp_ule_d, 0);
+	__this_cpu_write((fpuemustats).cmp_ult_s, 0);
+	__this_cpu_write((fpuemustats).cmp_ult_d, 0);
+	__this_cpu_write((fpuemustats).cmp_un_s, 0);
+	__this_cpu_write((fpuemustats).cmp_un_d, 0);
+	__this_cpu_write((fpuemustats).cmp_une_s, 0);
+	__this_cpu_write((fpuemustats).cmp_une_d, 0);
+	__this_cpu_write((fpuemustats).cmp_saf_s, 0);
+	__this_cpu_write((fpuemustats).cmp_saf_d, 0);
+	__this_cpu_write((fpuemustats).cmp_seq_s, 0);
+	__this_cpu_write((fpuemustats).cmp_seq_d, 0);
+	__this_cpu_write((fpuemustats).cmp_sle_s, 0);
+	__this_cpu_write((fpuemustats).cmp_sle_d, 0);
+	__this_cpu_write((fpuemustats).cmp_slt_s, 0);
+	__this_cpu_write((fpuemustats).cmp_slt_d, 0);
+	__this_cpu_write((fpuemustats).cmp_sne_s, 0);
+	__this_cpu_write((fpuemustats).cmp_sne_d, 0);
+	__this_cpu_write((fpuemustats).cmp_sor_s, 0);
+	__this_cpu_write((fpuemustats).cmp_sor_d, 0);
+	__this_cpu_write((fpuemustats).cmp_sueq_s, 0);
+	__this_cpu_write((fpuemustats).cmp_sueq_d, 0);
+	__this_cpu_write((fpuemustats).cmp_sule_s, 0);
+	__this_cpu_write((fpuemustats).cmp_sule_d, 0);
+	__this_cpu_write((fpuemustats).cmp_sult_s, 0);
+	__this_cpu_write((fpuemustats).cmp_sult_d, 0);
+	__this_cpu_write((fpuemustats).cmp_sun_s, 0);
+	__this_cpu_write((fpuemustats).cmp_sun_d, 0);
+	__this_cpu_write((fpuemustats).cmp_sune_s, 0);
+	__this_cpu_write((fpuemustats).cmp_sune_d, 0);
+	__this_cpu_write((fpuemustats).cvt_d_l, 0);
+	__this_cpu_write((fpuemustats).cvt_d_s, 0);
+	__this_cpu_write((fpuemustats).cvt_d_w, 0);
+	__this_cpu_write((fpuemustats).cvt_l_s, 0);
+	__this_cpu_write((fpuemustats).cvt_l_d, 0);
+	__this_cpu_write((fpuemustats).cvt_s_d, 0);
+	__this_cpu_write((fpuemustats).cvt_s_l, 0);
+	__this_cpu_write((fpuemustats).cvt_s_w, 0);
+	__this_cpu_write((fpuemustats).cvt_w_s, 0);
+	__this_cpu_write((fpuemustats).cvt_w_d, 0);
+	__this_cpu_write((fpuemustats).div_s, 0);
+	__this_cpu_write((fpuemustats).div_d, 0);
+	__this_cpu_write((fpuemustats).floor_w_s, 0);
+	__this_cpu_write((fpuemustats).floor_w_d, 0);
+	__this_cpu_write((fpuemustats).floor_l_s, 0);
+	__this_cpu_write((fpuemustats).floor_l_d, 0);
+	__this_cpu_write((fpuemustats).maddf_s, 0);
+	__this_cpu_write((fpuemustats).maddf_d, 0);
+	__this_cpu_write((fpuemustats).max_s, 0);
+	__this_cpu_write((fpuemustats).max_d, 0);
+	__this_cpu_write((fpuemustats).maxa_s, 0);
+	__this_cpu_write((fpuemustats).maxa_d, 0);
+	__this_cpu_write((fpuemustats).min_s, 0);
+	__this_cpu_write((fpuemustats).min_d, 0);
+	__this_cpu_write((fpuemustats).mina_s, 0);
+	__this_cpu_write((fpuemustats).mina_d, 0);
+	__this_cpu_write((fpuemustats).mov_s, 0);
+	__this_cpu_write((fpuemustats).mov_d, 0);
+	__this_cpu_write((fpuemustats).msubf_s, 0);
+	__this_cpu_write((fpuemustats).msubf_d, 0);
+	__this_cpu_write((fpuemustats).mul_s, 0);
+	__this_cpu_write((fpuemustats).mul_d, 0);
+	__this_cpu_write((fpuemustats).neg_s, 0);
+	__this_cpu_write((fpuemustats).neg_d, 0);
+	__this_cpu_write((fpuemustats).recip_s, 0);
+	__this_cpu_write((fpuemustats).recip_d, 0);
+	__this_cpu_write((fpuemustats).rint_s, 0);
+	__this_cpu_write((fpuemustats).rint_d, 0);
+	__this_cpu_write((fpuemustats).round_w_s, 0);
+	__this_cpu_write((fpuemustats).round_w_d, 0);
+	__this_cpu_write((fpuemustats).round_l_s, 0);
+	__this_cpu_write((fpuemustats).round_l_d, 0);
+	__this_cpu_write((fpuemustats).rsqrt_s, 0);
+	__this_cpu_write((fpuemustats).rsqrt_d, 0);
+	__this_cpu_write((fpuemustats).sel_s, 0);
+	__this_cpu_write((fpuemustats).sel_d, 0);
+	__this_cpu_write((fpuemustats).seleqz_s, 0);
+	__this_cpu_write((fpuemustats).seleqz_d, 0);
+	__this_cpu_write((fpuemustats).selnez_s, 0);
+	__this_cpu_write((fpuemustats).selnez_d, 0);
+	__this_cpu_write((fpuemustats).sqrt_s, 0);
+	__this_cpu_write((fpuemustats).sqrt_d, 0);
+	__this_cpu_write((fpuemustats).sub_s, 0);
+	__this_cpu_write((fpuemustats).sub_d, 0);
+	__this_cpu_write((fpuemustats).trunc_w_s, 0);
+	__this_cpu_write((fpuemustats).trunc_w_d, 0);
+	__this_cpu_write((fpuemustats).trunc_l_s, 0);
+	__this_cpu_write((fpuemustats).trunc_l_d, 0);
+
+	return 0;
+}
+
+DEFINE_SHOW_ATTRIBUTE(fpuemustats_clear);
+
+static int __init debugfs_fpuemu(void)
+{
+	struct dentry *fpuemu_debugfs_base_dir;
+	struct dentry *fpuemu_debugfs_inst_dir;
+	char name[32];
+
+	fpuemu_debugfs_base_dir = debugfs_create_dir("fpuemustats",
+						     mips_debugfs_dir);
+
+	debugfs_create_file("fpuemustats_clear", 0444, mips_debugfs_dir, NULL,
+			    &fpuemustats_clear_fops);
+
+#define FPU_EMU_STAT_OFFSET(m)						\
+	offsetof(struct mips_fpu_emulator_stats, m)
+
+#define FPU_STAT_CREATE(m)						\
+do {									\
+	debugfs_create_file(#m, 0444, fpuemu_debugfs_base_dir,		\
+				(void *)FPU_EMU_STAT_OFFSET(m),		\
+				&fops_fpuemu_stat);			\
+} while (0)
+
+	FPU_STAT_CREATE(emulated);
+	FPU_STAT_CREATE(loads);
+	FPU_STAT_CREATE(stores);
+	FPU_STAT_CREATE(branches);
+	FPU_STAT_CREATE(cp1ops);
+	FPU_STAT_CREATE(cp1xops);
+	FPU_STAT_CREATE(errors);
+	FPU_STAT_CREATE(ieee754_inexact);
+	FPU_STAT_CREATE(ieee754_underflow);
+	FPU_STAT_CREATE(ieee754_overflow);
+	FPU_STAT_CREATE(ieee754_zerodiv);
+	FPU_STAT_CREATE(ieee754_invalidop);
+	FPU_STAT_CREATE(ds_emul);
+
+	fpuemu_debugfs_inst_dir = debugfs_create_dir("instructions",
+						     fpuemu_debugfs_base_dir);
+
+#define FPU_STAT_CREATE_EX(m)						\
+do {									\
+	adjust_instruction_counter_name(name, #m);			\
+									\
+	debugfs_create_file(name, 0444, fpuemu_debugfs_inst_dir,	\
+				(void *)FPU_EMU_STAT_OFFSET(m),		\
+				&fops_fpuemu_stat);			\
+} while (0)
+
+	FPU_STAT_CREATE_EX(abs_s);
+	FPU_STAT_CREATE_EX(abs_d);
+	FPU_STAT_CREATE_EX(add_s);
+	FPU_STAT_CREATE_EX(add_d);
+	FPU_STAT_CREATE_EX(bc1eqz);
+	FPU_STAT_CREATE_EX(bc1nez);
+	FPU_STAT_CREATE_EX(ceil_w_s);
+	FPU_STAT_CREATE_EX(ceil_w_d);
+	FPU_STAT_CREATE_EX(ceil_l_s);
+	FPU_STAT_CREATE_EX(ceil_l_d);
+	FPU_STAT_CREATE_EX(class_s);
+	FPU_STAT_CREATE_EX(class_d);
+	FPU_STAT_CREATE_EX(cmp_af_s);
+	FPU_STAT_CREATE_EX(cmp_af_d);
+	FPU_STAT_CREATE_EX(cmp_eq_s);
+	FPU_STAT_CREATE_EX(cmp_eq_d);
+	FPU_STAT_CREATE_EX(cmp_le_s);
+	FPU_STAT_CREATE_EX(cmp_le_d);
+	FPU_STAT_CREATE_EX(cmp_lt_s);
+	FPU_STAT_CREATE_EX(cmp_lt_d);
+	FPU_STAT_CREATE_EX(cmp_ne_s);
+	FPU_STAT_CREATE_EX(cmp_ne_d);
+	FPU_STAT_CREATE_EX(cmp_or_s);
+	FPU_STAT_CREATE_EX(cmp_or_d);
+	FPU_STAT_CREATE_EX(cmp_ueq_s);
+	FPU_STAT_CREATE_EX(cmp_ueq_d);
+	FPU_STAT_CREATE_EX(cmp_ule_s);
+	FPU_STAT_CREATE_EX(cmp_ule_d);
+	FPU_STAT_CREATE_EX(cmp_ult_s);
+	FPU_STAT_CREATE_EX(cmp_ult_d);
+	FPU_STAT_CREATE_EX(cmp_un_s);
+	FPU_STAT_CREATE_EX(cmp_un_d);
+	FPU_STAT_CREATE_EX(cmp_une_s);
+	FPU_STAT_CREATE_EX(cmp_une_d);
+	FPU_STAT_CREATE_EX(cmp_saf_s);
+	FPU_STAT_CREATE_EX(cmp_saf_d);
+	FPU_STAT_CREATE_EX(cmp_seq_s);
+	FPU_STAT_CREATE_EX(cmp_seq_d);
+	FPU_STAT_CREATE_EX(cmp_sle_s);
+	FPU_STAT_CREATE_EX(cmp_sle_d);
+	FPU_STAT_CREATE_EX(cmp_slt_s);
+	FPU_STAT_CREATE_EX(cmp_slt_d);
+	FPU_STAT_CREATE_EX(cmp_sne_s);
+	FPU_STAT_CREATE_EX(cmp_sne_d);
+	FPU_STAT_CREATE_EX(cmp_sor_s);
+	FPU_STAT_CREATE_EX(cmp_sor_d);
+	FPU_STAT_CREATE_EX(cmp_sueq_s);
+	FPU_STAT_CREATE_EX(cmp_sueq_d);
+	FPU_STAT_CREATE_EX(cmp_sule_s);
+	FPU_STAT_CREATE_EX(cmp_sule_d);
+	FPU_STAT_CREATE_EX(cmp_sult_s);
+	FPU_STAT_CREATE_EX(cmp_sult_d);
+	FPU_STAT_CREATE_EX(cmp_sun_s);
+	FPU_STAT_CREATE_EX(cmp_sun_d);
+	FPU_STAT_CREATE_EX(cmp_sune_s);
+	FPU_STAT_CREATE_EX(cmp_sune_d);
+	FPU_STAT_CREATE_EX(cvt_d_l);
+	FPU_STAT_CREATE_EX(cvt_d_s);
+	FPU_STAT_CREATE_EX(cvt_d_w);
+	FPU_STAT_CREATE_EX(cvt_l_s);
+	FPU_STAT_CREATE_EX(cvt_l_d);
+	FPU_STAT_CREATE_EX(cvt_s_d);
+	FPU_STAT_CREATE_EX(cvt_s_l);
+	FPU_STAT_CREATE_EX(cvt_s_w);
+	FPU_STAT_CREATE_EX(cvt_w_s);
+	FPU_STAT_CREATE_EX(cvt_w_d);
+	FPU_STAT_CREATE_EX(div_s);
+	FPU_STAT_CREATE_EX(div_d);
+	FPU_STAT_CREATE_EX(floor_w_s);
+	FPU_STAT_CREATE_EX(floor_w_d);
+	FPU_STAT_CREATE_EX(floor_l_s);
+	FPU_STAT_CREATE_EX(floor_l_d);
+	FPU_STAT_CREATE_EX(maddf_s);
+	FPU_STAT_CREATE_EX(maddf_d);
+	FPU_STAT_CREATE_EX(max_s);
+	FPU_STAT_CREATE_EX(max_d);
+	FPU_STAT_CREATE_EX(maxa_s);
+	FPU_STAT_CREATE_EX(maxa_d);
+	FPU_STAT_CREATE_EX(min_s);
+	FPU_STAT_CREATE_EX(min_d);
+	FPU_STAT_CREATE_EX(mina_s);
+	FPU_STAT_CREATE_EX(mina_d);
+	FPU_STAT_CREATE_EX(mov_s);
+	FPU_STAT_CREATE_EX(mov_d);
+	FPU_STAT_CREATE_EX(msubf_s);
+	FPU_STAT_CREATE_EX(msubf_d);
+	FPU_STAT_CREATE_EX(mul_s);
+	FPU_STAT_CREATE_EX(mul_d);
+	FPU_STAT_CREATE_EX(neg_s);
+	FPU_STAT_CREATE_EX(neg_d);
+	FPU_STAT_CREATE_EX(recip_s);
+	FPU_STAT_CREATE_EX(recip_d);
+	FPU_STAT_CREATE_EX(rint_s);
+	FPU_STAT_CREATE_EX(rint_d);
+	FPU_STAT_CREATE_EX(round_w_s);
+	FPU_STAT_CREATE_EX(round_w_d);
+	FPU_STAT_CREATE_EX(round_l_s);
+	FPU_STAT_CREATE_EX(round_l_d);
+	FPU_STAT_CREATE_EX(rsqrt_s);
+	FPU_STAT_CREATE_EX(rsqrt_d);
+	FPU_STAT_CREATE_EX(sel_s);
+	FPU_STAT_CREATE_EX(sel_d);
+	FPU_STAT_CREATE_EX(seleqz_s);
+	FPU_STAT_CREATE_EX(seleqz_d);
+	FPU_STAT_CREATE_EX(selnez_s);
+	FPU_STAT_CREATE_EX(selnez_d);
+	FPU_STAT_CREATE_EX(sqrt_s);
+	FPU_STAT_CREATE_EX(sqrt_d);
+	FPU_STAT_CREATE_EX(sub_s);
+	FPU_STAT_CREATE_EX(sub_d);
+	FPU_STAT_CREATE_EX(trunc_w_s);
+	FPU_STAT_CREATE_EX(trunc_w_d);
+	FPU_STAT_CREATE_EX(trunc_l_s);
+	FPU_STAT_CREATE_EX(trunc_l_d);
+
+	return 0;
+}
+arch_initcall(debugfs_fpuemu);
diff --git a/arch/mips/math-emu/sp_2008class.c b/arch/mips/math-emu/sp_2008class.c
new file mode 100644
index 000000000..b9adab6c2
--- /dev/null
+++ b/arch/mips/math-emu/sp_2008class.c
@@ -0,0 +1,52 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * IEEE754 floating point arithmetic
+ * single precision: CLASS.f
+ * FPR[fd] = class(FPR[fs])
+ *
+ * MIPS floating point support
+ * Copyright (C) 2015 Imagination Technologies, Ltd.
+ * Author: Markos Chandras <markos.chandras@imgtec.com>
+ */
+
+#include "ieee754sp.h"
+
+int ieee754sp_2008class(union ieee754sp x)
+{
+	COMPXSP;
+
+	EXPLODEXSP;
+
+	/*
+	 * 10 bit mask as follows:
+	 *
+	 * bit0 = SNAN
+	 * bit1 = QNAN
+	 * bit2 = -INF
+	 * bit3 = -NORM
+	 * bit4 = -DNORM
+	 * bit5 = -ZERO
+	 * bit6 = INF
+	 * bit7 = NORM
+	 * bit8 = DNORM
+	 * bit9 = ZERO
+	 */
+
+	switch(xc) {
+	case IEEE754_CLASS_SNAN:
+		return 0x01;
+	case IEEE754_CLASS_QNAN:
+		return 0x02;
+	case IEEE754_CLASS_INF:
+		return 0x04 << (xs ? 0 : 4);
+	case IEEE754_CLASS_NORM:
+		return 0x08 << (xs ? 0 : 4);
+	case IEEE754_CLASS_DNORM:
+		return 0x10 << (xs ? 0 : 4);
+	case IEEE754_CLASS_ZERO:
+		return 0x20 << (xs ? 0 : 4);
+	default:
+		pr_err("Unknown class: %d\n", xc);
+		return 0;
+	}
+}
diff --git a/arch/mips/math-emu/sp_add.c b/arch/mips/math-emu/sp_add.c
new file mode 100644
index 000000000..715cd0534
--- /dev/null
+++ b/arch/mips/math-emu/sp_add.c
@@ -0,0 +1,164 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* IEEE754 floating point arithmetic
+ * single precision
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ */
+
+#include "ieee754sp.h"
+
+union ieee754sp ieee754sp_add(union ieee754sp x, union ieee754sp y)
+{
+	int s;
+
+	COMPXSP;
+	COMPYSP;
+
+	EXPLODEXSP;
+	EXPLODEYSP;
+
+	ieee754_clearcx();
+
+	FLUSHXSP;
+	FLUSHYSP;
+
+	switch (CLPAIR(xc, yc)) {
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_SNAN):
+		return ieee754sp_nanxcpt(y);
+
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_INF):
+		return ieee754sp_nanxcpt(x);
+
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_QNAN):
+		return y;
+
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_INF):
+		return x;
+
+
+	/*
+	 * Infinity handling
+	 */
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_INF):
+		if (xs == ys)
+			return x;
+		ieee754_setcx(IEEE754_INVALID_OPERATION);
+		return ieee754sp_indef();
+
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_INF):
+		return y;
+
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_DNORM):
+		return x;
+
+	/*
+	 * Zero handling
+	 */
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_ZERO):
+		if (xs == ys)
+			return x;
+		else
+			return ieee754sp_zero(ieee754_csr.rm == FPU_CSR_RD);
+
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_ZERO):
+		return x;
+
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_DNORM):
+		return y;
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_DNORM):
+		SPDNORMX;
+		fallthrough;
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_DNORM):
+		SPDNORMY;
+		break;
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_NORM):
+		SPDNORMX;
+		break;
+
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_NORM):
+		break;
+	}
+	assert(xm & SP_HIDDEN_BIT);
+	assert(ym & SP_HIDDEN_BIT);
+
+	/*
+	 * Provide guard, round and stick bit space.
+	 */
+	xm <<= 3;
+	ym <<= 3;
+
+	if (xe > ye) {
+		/*
+		 * Have to shift y fraction right to align.
+		 */
+		s = xe - ye;
+		ym = XSPSRS(ym, s);
+		ye += s;
+	} else if (ye > xe) {
+		/*
+		 * Have to shift x fraction right to align.
+		 */
+		s = ye - xe;
+		xm = XSPSRS(xm, s);
+		xe += s;
+	}
+	assert(xe == ye);
+	assert(xe <= SP_EMAX);
+
+	if (xs == ys) {
+		/*
+		 * Generate 28 bit result of adding two 27 bit numbers
+		 * leaving result in xm, xs and xe.
+		 */
+		xm = xm + ym;
+
+		if (xm >> (SP_FBITS + 1 + 3)) { /* carry out */
+			SPXSRSX1();
+		}
+	} else {
+		if (xm >= ym) {
+			xm = xm - ym;
+		} else {
+			xm = ym - xm;
+			xs = ys;
+		}
+		if (xm == 0)
+			return ieee754sp_zero(ieee754_csr.rm == FPU_CSR_RD);
+
+		/*
+		 * Normalize in extended single precision
+		 */
+		while ((xm >> (SP_FBITS + 3)) == 0) {
+			xm <<= 1;
+			xe--;
+		}
+	}
+
+	return ieee754sp_format(xs, xe, xm);
+}
diff --git a/arch/mips/math-emu/sp_cmp.c b/arch/mips/math-emu/sp_cmp.c
new file mode 100644
index 000000000..64a37362a
--- /dev/null
+++ b/arch/mips/math-emu/sp_cmp.c
@@ -0,0 +1,47 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* IEEE754 floating point arithmetic
+ * single precision
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ */
+
+#include "ieee754sp.h"
+
+int ieee754sp_cmp(union ieee754sp x, union ieee754sp y, int cmp, int sig)
+{
+	int vx;
+	int vy;
+
+	COMPXSP;
+	COMPYSP;
+
+	EXPLODEXSP;
+	EXPLODEYSP;
+	FLUSHXSP;
+	FLUSHYSP;
+	ieee754_clearcx();	/* Even clear inexact flag here */
+
+	if (ieee754_class_nan(xc) || ieee754_class_nan(yc)) {
+		if (sig ||
+		    xc == IEEE754_CLASS_SNAN || yc == IEEE754_CLASS_SNAN)
+			ieee754_setcx(IEEE754_INVALID_OPERATION);
+		return (cmp & IEEE754_CUN) != 0;
+	} else {
+		vx = x.bits;
+		vy = y.bits;
+
+		if (vx < 0)
+			vx = -vx ^ SP_SIGN_BIT;
+		if (vy < 0)
+			vy = -vy ^ SP_SIGN_BIT;
+
+		if (vx < vy)
+			return (cmp & IEEE754_CLT) != 0;
+		else if (vx == vy)
+			return (cmp & IEEE754_CEQ) != 0;
+		else
+			return (cmp & IEEE754_CGT) != 0;
+	}
+}
diff --git a/arch/mips/math-emu/sp_div.c b/arch/mips/math-emu/sp_div.c
new file mode 100644
index 000000000..2bfa266fd
--- /dev/null
+++ b/arch/mips/math-emu/sp_div.c
@@ -0,0 +1,142 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* IEEE754 floating point arithmetic
+ * single precision
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ */
+
+#include "ieee754sp.h"
+
+union ieee754sp ieee754sp_div(union ieee754sp x, union ieee754sp y)
+{
+	unsigned int rm;
+	int re;
+	unsigned int bm;
+
+	COMPXSP;
+	COMPYSP;
+
+	EXPLODEXSP;
+	EXPLODEYSP;
+
+	ieee754_clearcx();
+
+	FLUSHXSP;
+	FLUSHYSP;
+
+	switch (CLPAIR(xc, yc)) {
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_SNAN):
+		return ieee754sp_nanxcpt(y);
+
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_INF):
+		return ieee754sp_nanxcpt(x);
+
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_QNAN):
+		return y;
+
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_INF):
+		return x;
+
+
+	/*
+	 * Infinity handling
+	 */
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_INF):
+		ieee754_setcx(IEEE754_INVALID_OPERATION);
+		return ieee754sp_indef();
+
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_INF):
+		return ieee754sp_zero(xs ^ ys);
+
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_DNORM):
+		return ieee754sp_inf(xs ^ ys);
+
+	/*
+	 * Zero handling
+	 */
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_ZERO):
+		ieee754_setcx(IEEE754_INVALID_OPERATION);
+		return ieee754sp_indef();
+
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_ZERO):
+		ieee754_setcx(IEEE754_ZERO_DIVIDE);
+		return ieee754sp_inf(xs ^ ys);
+
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_DNORM):
+		return ieee754sp_zero(xs == ys ? 0 : 1);
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_DNORM):
+		SPDNORMX;
+		fallthrough;
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_DNORM):
+		SPDNORMY;
+		break;
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_NORM):
+		SPDNORMX;
+		break;
+
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_NORM):
+		break;
+	}
+	assert(xm & SP_HIDDEN_BIT);
+	assert(ym & SP_HIDDEN_BIT);
+
+	/* provide rounding space */
+	xm <<= 3;
+	ym <<= 3;
+
+	/* now the dirty work */
+
+	rm = 0;
+	re = xe - ye;
+
+	for (bm = SP_MBIT(SP_FBITS + 2); bm; bm >>= 1) {
+		if (xm >= ym) {
+			xm -= ym;
+			rm |= bm;
+			if (xm == 0)
+				break;
+		}
+		xm <<= 1;
+	}
+
+	rm <<= 1;
+	if (xm)
+		rm |= 1;	/* have remainder, set sticky */
+
+	assert(rm);
+
+	/* normalise rm to rounding precision ?
+	 */
+	while ((rm >> (SP_FBITS + 3)) == 0) {
+		rm <<= 1;
+		re--;
+	}
+
+	return ieee754sp_format(xs == ys ? 0 : 1, re, rm);
+}
diff --git a/arch/mips/math-emu/sp_fdp.c b/arch/mips/math-emu/sp_fdp.c
new file mode 100644
index 000000000..56417497c
--- /dev/null
+++ b/arch/mips/math-emu/sp_fdp.c
@@ -0,0 +1,73 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* IEEE754 floating point arithmetic
+ * single precision
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ */
+
+#include "ieee754sp.h"
+#include "ieee754dp.h"
+
+static inline union ieee754sp ieee754sp_nan_fdp(int xs, u64 xm)
+{
+	return buildsp(xs, SP_EMAX + 1 + SP_EBIAS,
+		       xm >> (DP_FBITS - SP_FBITS));
+}
+
+union ieee754sp ieee754sp_fdp(union ieee754dp x)
+{
+	union ieee754sp y;
+	u32 rm;
+
+	COMPXDP;
+	COMPYSP;
+
+	EXPLODEXDP;
+
+	ieee754_clearcx();
+
+	FLUSHXDP;
+
+	switch (xc) {
+	case IEEE754_CLASS_SNAN:
+		x = ieee754dp_nanxcpt(x);
+		EXPLODEXDP;
+		fallthrough;
+	case IEEE754_CLASS_QNAN:
+		y = ieee754sp_nan_fdp(xs, xm);
+		if (!ieee754_csr.nan2008) {
+			EXPLODEYSP;
+			if (!ieee754_class_nan(yc))
+				y = ieee754sp_indef();
+		}
+		return y;
+
+	case IEEE754_CLASS_INF:
+		return ieee754sp_inf(xs);
+
+	case IEEE754_CLASS_ZERO:
+		return ieee754sp_zero(xs);
+
+	case IEEE754_CLASS_DNORM:
+		/* can't possibly be sp representable */
+		ieee754_setcx(IEEE754_UNDERFLOW);
+		ieee754_setcx(IEEE754_INEXACT);
+		if ((ieee754_csr.rm == FPU_CSR_RU && !xs) ||
+				(ieee754_csr.rm == FPU_CSR_RD && xs))
+			return ieee754sp_mind(xs);
+		return ieee754sp_zero(xs);
+
+	case IEEE754_CLASS_NORM:
+		break;
+	}
+
+	/*
+	 * Convert from DP_FBITS to SP_FBITS+3 with sticky right shift.
+	 */
+	rm = (xm >> (DP_FBITS - (SP_FBITS + 3))) |
+	     ((xm << (64 - (DP_FBITS - (SP_FBITS + 3)))) != 0);
+
+	return ieee754sp_format(xs, xe, rm);
+}
diff --git a/arch/mips/math-emu/sp_fint.c b/arch/mips/math-emu/sp_fint.c
new file mode 100644
index 000000000..6068e3caa
--- /dev/null
+++ b/arch/mips/math-emu/sp_fint.c
@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* IEEE754 floating point arithmetic
+ * single precision
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ */
+
+#include "ieee754sp.h"
+
+union ieee754sp ieee754sp_fint(int x)
+{
+	unsigned int xm;
+	int xe;
+	int xs;
+
+	ieee754_clearcx();
+
+	if (x == 0)
+		return ieee754sp_zero(0);
+	if (x == 1 || x == -1)
+		return ieee754sp_one(x < 0);
+	if (x == 10 || x == -10)
+		return ieee754sp_ten(x < 0);
+
+	xs = (x < 0);
+	if (xs) {
+		if (x == (1 << 31))
+			xm = ((unsigned) 1 << 31);	/* max neg can't be safely negated */
+		else
+			xm = -x;
+	} else {
+		xm = x;
+	}
+	xe = SP_FBITS + 3;
+
+	if (xm >> (SP_FBITS + 1 + 3)) {
+		/* shunt out overflow bits
+		 */
+		while (xm >> (SP_FBITS + 1 + 3)) {
+			SPXSRSX1();
+		}
+	} else {
+		/* normalize in grs extended single precision
+		 */
+		while ((xm >> (SP_FBITS + 3)) == 0) {
+			xm <<= 1;
+			xe--;
+		}
+	}
+	return ieee754sp_format(xs, xe, xm);
+}
diff --git a/arch/mips/math-emu/sp_flong.c b/arch/mips/math-emu/sp_flong.c
new file mode 100644
index 000000000..1b223fb5a
--- /dev/null
+++ b/arch/mips/math-emu/sp_flong.c
@@ -0,0 +1,52 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* IEEE754 floating point arithmetic
+ * single precision
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ */
+
+#include "ieee754sp.h"
+
+union ieee754sp ieee754sp_flong(s64 x)
+{
+	u64 xm;		/* <--- need 64-bit mantissa temp */
+	int xe;
+	int xs;
+
+	ieee754_clearcx();
+
+	if (x == 0)
+		return ieee754sp_zero(0);
+	if (x == 1 || x == -1)
+		return ieee754sp_one(x < 0);
+	if (x == 10 || x == -10)
+		return ieee754sp_ten(x < 0);
+
+	xs = (x < 0);
+	if (xs) {
+		if (x == (1ULL << 63))
+			xm = (1ULL << 63);	/* max neg can't be safely negated */
+		else
+			xm = -x;
+	} else {
+		xm = x;
+	}
+	xe = SP_FBITS + 3;
+
+	if (xm >> (SP_FBITS + 1 + 3)) {
+		/* shunt out overflow bits
+		 */
+		while (xm >> (SP_FBITS + 1 + 3)) {
+			SPXSRSX1();
+		}
+	} else {
+		/* normalize in grs extended single precision */
+		while ((xm >> (SP_FBITS + 3)) == 0) {
+			xm <<= 1;
+			xe--;
+		}
+	}
+	return ieee754sp_format(xs, xe, xm);
+}
diff --git a/arch/mips/math-emu/sp_fmax.c b/arch/mips/math-emu/sp_fmax.c
new file mode 100644
index 000000000..3fb16a1df
--- /dev/null
+++ b/arch/mips/math-emu/sp_fmax.c
@@ -0,0 +1,252 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * IEEE754 floating point arithmetic
+ * single precision: MAX{,A}.f
+ * MAX : Scalar Floating-Point Maximum
+ * MAXA: Scalar Floating-Point argument with Maximum Absolute Value
+ *
+ * MAX.S : FPR[fd] = maxNum(FPR[fs],FPR[ft])
+ * MAXA.S: FPR[fd] = maxNumMag(FPR[fs],FPR[ft])
+ *
+ * MIPS floating point support
+ * Copyright (C) 2015 Imagination Technologies, Ltd.
+ * Author: Markos Chandras <markos.chandras@imgtec.com>
+ */
+
+#include "ieee754sp.h"
+
+union ieee754sp ieee754sp_fmax(union ieee754sp x, union ieee754sp y)
+{
+	COMPXSP;
+	COMPYSP;
+
+	EXPLODEXSP;
+	EXPLODEYSP;
+
+	FLUSHXSP;
+	FLUSHYSP;
+
+	ieee754_clearcx();
+
+	switch (CLPAIR(xc, yc)) {
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_SNAN):
+		return ieee754sp_nanxcpt(y);
+
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_INF):
+		return ieee754sp_nanxcpt(x);
+
+	/*
+	 * Quiet NaN handling
+	 */
+
+	/*
+	 *    The case of both inputs quiet NaNs
+	 */
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_QNAN):
+		return x;
+
+	/*
+	 *    The cases of exactly one input quiet NaN (numbers
+	 *    are here preferred as returned values to NaNs)
+	 */
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_QNAN):
+		return x;
+
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_INF):
+		return y;
+
+	/*
+	 * Infinity and zero handling
+	 */
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_ZERO):
+		return xs ? y : x;
+
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_DNORM):
+		return ys ? x : y;
+
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_ZERO):
+		return ieee754sp_zero(xs & ys);
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_DNORM):
+		SPDNORMX;
+		fallthrough;
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_DNORM):
+		SPDNORMY;
+		break;
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_NORM):
+		SPDNORMX;
+	}
+
+	/* Finally get to do some computation */
+
+	assert(xm & SP_HIDDEN_BIT);
+	assert(ym & SP_HIDDEN_BIT);
+
+	/* Compare signs */
+	if (xs > ys)
+		return y;
+	else if (xs < ys)
+		return x;
+
+	/* Signs of inputs are equal, let's compare exponents */
+	if (xs == 0) {
+		/* Inputs are both positive */
+		if (xe > ye)
+			return x;
+		else if (xe < ye)
+			return y;
+	} else {
+		/* Inputs are both negative */
+		if (xe > ye)
+			return y;
+		else if (xe < ye)
+			return x;
+	}
+
+	/* Signs and exponents of inputs are equal, let's compare mantissas */
+	if (xs == 0) {
+		/* Inputs are both positive, with equal signs and exponents */
+		if (xm <= ym)
+			return y;
+		return x;
+	}
+	/* Inputs are both negative, with equal signs and exponents */
+	if (xm <= ym)
+		return x;
+	return y;
+}
+
+union ieee754sp ieee754sp_fmaxa(union ieee754sp x, union ieee754sp y)
+{
+	COMPXSP;
+	COMPYSP;
+
+	EXPLODEXSP;
+	EXPLODEYSP;
+
+	FLUSHXSP;
+	FLUSHYSP;
+
+	ieee754_clearcx();
+
+	switch (CLPAIR(xc, yc)) {
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_SNAN):
+		return ieee754sp_nanxcpt(y);
+
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_INF):
+		return ieee754sp_nanxcpt(x);
+
+	/*
+	 * Quiet NaN handling
+	 */
+
+	/*
+	 *    The case of both inputs quiet NaNs
+	 */
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_QNAN):
+		return x;
+
+	/*
+	 *    The cases of exactly one input quiet NaN (numbers
+	 *    are here preferred as returned values to NaNs)
+	 */
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_QNAN):
+		return x;
+
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_INF):
+		return y;
+
+	/*
+	 * Infinity and zero handling
+	 */
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_INF):
+		return ieee754sp_inf(xs & ys);
+
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_ZERO):
+		return x;
+
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_DNORM):
+		return y;
+
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_ZERO):
+		return ieee754sp_zero(xs & ys);
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_DNORM):
+		SPDNORMX;
+		fallthrough;
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_DNORM):
+		SPDNORMY;
+		break;
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_NORM):
+		SPDNORMX;
+	}
+
+	/* Finally get to do some computation */
+
+	assert(xm & SP_HIDDEN_BIT);
+	assert(ym & SP_HIDDEN_BIT);
+
+	/* Compare exponent */
+	if (xe > ye)
+		return x;
+	else if (xe < ye)
+		return y;
+
+	/* Compare mantissa */
+	if (xm < ym)
+		return y;
+	else if (xm > ym)
+		return x;
+	else if (xs == 0)
+		return x;
+	return y;
+}
diff --git a/arch/mips/math-emu/sp_fmin.c b/arch/mips/math-emu/sp_fmin.c
new file mode 100644
index 000000000..ad2599d4a
--- /dev/null
+++ b/arch/mips/math-emu/sp_fmin.c
@@ -0,0 +1,252 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * IEEE754 floating point arithmetic
+ * single precision: MIN{,A}.f
+ * MIN : Scalar Floating-Point Minimum
+ * MINA: Scalar Floating-Point argument with Minimum Absolute Value
+ *
+ * MIN.S : FPR[fd] = minNum(FPR[fs],FPR[ft])
+ * MINA.S: FPR[fd] = maxNumMag(FPR[fs],FPR[ft])
+ *
+ * MIPS floating point support
+ * Copyright (C) 2015 Imagination Technologies, Ltd.
+ * Author: Markos Chandras <markos.chandras@imgtec.com>
+ */
+
+#include "ieee754sp.h"
+
+union ieee754sp ieee754sp_fmin(union ieee754sp x, union ieee754sp y)
+{
+	COMPXSP;
+	COMPYSP;
+
+	EXPLODEXSP;
+	EXPLODEYSP;
+
+	FLUSHXSP;
+	FLUSHYSP;
+
+	ieee754_clearcx();
+
+	switch (CLPAIR(xc, yc)) {
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_SNAN):
+		return ieee754sp_nanxcpt(y);
+
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_INF):
+		return ieee754sp_nanxcpt(x);
+
+	/*
+	 * Quiet NaN handling
+	 */
+
+	/*
+	 *    The case of both inputs quiet NaNs
+	 */
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_QNAN):
+		return x;
+
+	/*
+	 *    The cases of exactly one input quiet NaN (numbers
+	 *    are here preferred as returned values to NaNs)
+	 */
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_QNAN):
+		return x;
+
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_INF):
+		return y;
+
+	/*
+	 * Infinity and zero handling
+	 */
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_ZERO):
+		return xs ? x : y;
+
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_DNORM):
+		return ys ? y : x;
+
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_ZERO):
+		return ieee754sp_zero(xs | ys);
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_DNORM):
+		SPDNORMX;
+		fallthrough;
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_DNORM):
+		SPDNORMY;
+		break;
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_NORM):
+		SPDNORMX;
+	}
+
+	/* Finally get to do some computation */
+
+	assert(xm & SP_HIDDEN_BIT);
+	assert(ym & SP_HIDDEN_BIT);
+
+	/* Compare signs */
+	if (xs > ys)
+		return x;
+	else if (xs < ys)
+		return y;
+
+	/* Signs of inputs are the same, let's compare exponents */
+	if (xs == 0) {
+		/* Inputs are both positive */
+		if (xe > ye)
+			return y;
+		else if (xe < ye)
+			return x;
+	} else {
+		/* Inputs are both negative */
+		if (xe > ye)
+			return x;
+		else if (xe < ye)
+			return y;
+	}
+
+	/* Signs and exponents of inputs are equal, let's compare mantissas */
+	if (xs == 0) {
+		/* Inputs are both positive, with equal signs and exponents */
+		if (xm <= ym)
+			return x;
+		return y;
+	}
+	/* Inputs are both negative, with equal signs and exponents */
+	if (xm <= ym)
+		return y;
+	return x;
+}
+
+union ieee754sp ieee754sp_fmina(union ieee754sp x, union ieee754sp y)
+{
+	COMPXSP;
+	COMPYSP;
+
+	EXPLODEXSP;
+	EXPLODEYSP;
+
+	FLUSHXSP;
+	FLUSHYSP;
+
+	ieee754_clearcx();
+
+	switch (CLPAIR(xc, yc)) {
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_SNAN):
+		return ieee754sp_nanxcpt(y);
+
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_INF):
+		return ieee754sp_nanxcpt(x);
+
+	/*
+	 * Quiet NaN handling
+	 */
+
+	/*
+	 *    The case of both inputs quiet NaNs
+	 */
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_QNAN):
+		return x;
+
+	/*
+	 *    The cases of exactly one input quiet NaN (numbers
+	 *    are here preferred as returned values to NaNs)
+	 */
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_QNAN):
+		return x;
+
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_INF):
+		return y;
+
+	/*
+	 * Infinity and zero handling
+	 */
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_INF):
+		return ieee754sp_inf(xs | ys);
+
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_ZERO):
+		return y;
+
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_DNORM):
+		return x;
+
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_ZERO):
+		return ieee754sp_zero(xs | ys);
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_DNORM):
+		SPDNORMX;
+		fallthrough;
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_DNORM):
+		SPDNORMY;
+		break;
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_NORM):
+		SPDNORMX;
+	}
+
+	/* Finally get to do some computation */
+
+	assert(xm & SP_HIDDEN_BIT);
+	assert(ym & SP_HIDDEN_BIT);
+
+	/* Compare exponent */
+	if (xe > ye)
+		return y;
+	else if (xe < ye)
+		return x;
+
+	/* Compare mantissa */
+	if (xm < ym)
+		return x;
+	else if (xm > ym)
+		return y;
+	else if (xs == 1)
+		return x;
+	return y;
+}
diff --git a/arch/mips/math-emu/sp_maddf.c b/arch/mips/math-emu/sp_maddf.c
new file mode 100644
index 000000000..473ee222d
--- /dev/null
+++ b/arch/mips/math-emu/sp_maddf.c
@@ -0,0 +1,278 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * IEEE754 floating point arithmetic
+ * single precision: MADDF.f (Fused Multiply Add)
+ * MADDF.fmt: FPR[fd] = FPR[fd] + (FPR[fs] x FPR[ft])
+ *
+ * MIPS floating point support
+ * Copyright (C) 2015 Imagination Technologies, Ltd.
+ * Author: Markos Chandras <markos.chandras@imgtec.com>
+ */
+
+#include "ieee754sp.h"
+
+
+static union ieee754sp _sp_maddf(union ieee754sp z, union ieee754sp x,
+				 union ieee754sp y, enum maddf_flags flags)
+{
+	int re;
+	int rs;
+	unsigned int rm;
+	u64 rm64;
+	u64 zm64;
+	int s;
+
+	COMPXSP;
+	COMPYSP;
+	COMPZSP;
+
+	EXPLODEXSP;
+	EXPLODEYSP;
+	EXPLODEZSP;
+
+	FLUSHXSP;
+	FLUSHYSP;
+	FLUSHZSP;
+
+	ieee754_clearcx();
+
+	rs = xs ^ ys;
+	if (flags & MADDF_NEGATE_PRODUCT)
+		rs ^= 1;
+	if (flags & MADDF_NEGATE_ADDITION)
+		zs ^= 1;
+
+	/*
+	 * Handle the cases when at least one of x, y or z is a NaN.
+	 * Order of precedence is sNaN, qNaN and z, x, y.
+	 */
+	if (zc == IEEE754_CLASS_SNAN)
+		return ieee754sp_nanxcpt(z);
+	if (xc == IEEE754_CLASS_SNAN)
+		return ieee754sp_nanxcpt(x);
+	if (yc == IEEE754_CLASS_SNAN)
+		return ieee754sp_nanxcpt(y);
+	if (zc == IEEE754_CLASS_QNAN)
+		return z;
+	if (xc == IEEE754_CLASS_QNAN)
+		return x;
+	if (yc == IEEE754_CLASS_QNAN)
+		return y;
+
+	if (zc == IEEE754_CLASS_DNORM)
+		SPDNORMZ;
+	/* ZERO z cases are handled separately below */
+
+	switch (CLPAIR(xc, yc)) {
+
+
+	/*
+	 * Infinity handling
+	 */
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_INF):
+		ieee754_setcx(IEEE754_INVALID_OPERATION);
+		return ieee754sp_indef();
+
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_INF):
+		if ((zc == IEEE754_CLASS_INF) && (zs != rs)) {
+			/*
+			 * Cases of addition of infinities with opposite signs
+			 * or subtraction of infinities with same signs.
+			 */
+			ieee754_setcx(IEEE754_INVALID_OPERATION);
+			return ieee754sp_indef();
+		}
+		/*
+		 * z is here either not an infinity, or an infinity having the
+		 * same sign as product (x*y). The result must be an infinity,
+		 * and its sign is determined only by the sign of product (x*y).
+		 */
+		return ieee754sp_inf(rs);
+
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_ZERO):
+		if (zc == IEEE754_CLASS_INF)
+			return ieee754sp_inf(zs);
+		if (zc == IEEE754_CLASS_ZERO) {
+			/* Handle cases +0 + (-0) and similar ones. */
+			if (zs == rs)
+				/*
+				 * Cases of addition of zeros of equal signs
+				 * or subtraction of zeroes of opposite signs.
+				 * The sign of the resulting zero is in any
+				 * such case determined only by the sign of z.
+				 */
+				return z;
+
+			return ieee754sp_zero(ieee754_csr.rm == FPU_CSR_RD);
+		}
+		/* x*y is here 0, and z is not 0, so just return z */
+		return z;
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_DNORM):
+		SPDNORMX;
+		fallthrough;
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_DNORM):
+		if (zc == IEEE754_CLASS_INF)
+			return ieee754sp_inf(zs);
+		SPDNORMY;
+		break;
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_NORM):
+		if (zc == IEEE754_CLASS_INF)
+			return ieee754sp_inf(zs);
+		SPDNORMX;
+		break;
+
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_NORM):
+		if (zc == IEEE754_CLASS_INF)
+			return ieee754sp_inf(zs);
+		/* continue to real computations */
+	}
+
+	/* Finally get to do some computation */
+
+	/*
+	 * Do the multiplication bit first
+	 *
+	 * rm = xm * ym, re = xe + ye basically
+	 *
+	 * At this point xm and ym should have been normalized.
+	 */
+
+	/* rm = xm * ym, re = xe+ye basically */
+	assert(xm & SP_HIDDEN_BIT);
+	assert(ym & SP_HIDDEN_BIT);
+
+	re = xe + ye;
+
+	/* Multiple 24 bit xm and ym to give 48 bit results */
+	rm64 = (uint64_t)xm * ym;
+
+	/* Shunt to top of word */
+	rm64 = rm64 << 16;
+
+	/* Put explicit bit at bit 62 if necessary */
+	if ((int64_t) rm64 < 0) {
+		rm64 = rm64 >> 1;
+		re++;
+	}
+
+	assert(rm64 & (1 << 62));
+
+	if (zc == IEEE754_CLASS_ZERO) {
+		/*
+		 * Move explicit bit from bit 62 to bit 26 since the
+		 * ieee754sp_format code expects the mantissa to be
+		 * 27 bits wide (24 + 3 rounding bits).
+		 */
+		rm = XSPSRS64(rm64, (62 - 26));
+		return ieee754sp_format(rs, re, rm);
+	}
+
+	/* Move explicit bit from bit 23 to bit 62 */
+	zm64 = (uint64_t)zm << (62 - 23);
+	assert(zm64 & (1 << 62));
+
+	/* Make the exponents the same */
+	if (ze > re) {
+		/*
+		 * Have to shift r fraction right to align.
+		 */
+		s = ze - re;
+		rm64 = XSPSRS64(rm64, s);
+		re += s;
+	} else if (re > ze) {
+		/*
+		 * Have to shift z fraction right to align.
+		 */
+		s = re - ze;
+		zm64 = XSPSRS64(zm64, s);
+		ze += s;
+	}
+	assert(ze == re);
+	assert(ze <= SP_EMAX);
+
+	/* Do the addition */
+	if (zs == rs) {
+		/*
+		 * Generate 64 bit result by adding two 63 bit numbers
+		 * leaving result in zm64, zs and ze.
+		 */
+		zm64 = zm64 + rm64;
+		if ((int64_t)zm64 < 0) {	/* carry out */
+			zm64 = XSPSRS1(zm64);
+			ze++;
+		}
+	} else {
+		if (zm64 >= rm64) {
+			zm64 = zm64 - rm64;
+		} else {
+			zm64 = rm64 - zm64;
+			zs = rs;
+		}
+		if (zm64 == 0)
+			return ieee754sp_zero(ieee754_csr.rm == FPU_CSR_RD);
+
+		/*
+		 * Put explicit bit at bit 62 if necessary.
+		 */
+		while ((zm64 >> 62) == 0) {
+			zm64 <<= 1;
+			ze--;
+		}
+	}
+
+	/*
+	 * Move explicit bit from bit 62 to bit 26 since the
+	 * ieee754sp_format code expects the mantissa to be
+	 * 27 bits wide (24 + 3 rounding bits).
+	 */
+	zm = XSPSRS64(zm64, (62 - 26));
+
+	return ieee754sp_format(zs, ze, zm);
+}
+
+union ieee754sp ieee754sp_maddf(union ieee754sp z, union ieee754sp x,
+				union ieee754sp y)
+{
+	return _sp_maddf(z, x, y, 0);
+}
+
+union ieee754sp ieee754sp_msubf(union ieee754sp z, union ieee754sp x,
+				union ieee754sp y)
+{
+	return _sp_maddf(z, x, y, MADDF_NEGATE_PRODUCT);
+}
+
+union ieee754sp ieee754sp_madd(union ieee754sp z, union ieee754sp x,
+				union ieee754sp y)
+{
+	return _sp_maddf(z, x, y, 0);
+}
+
+union ieee754sp ieee754sp_msub(union ieee754sp z, union ieee754sp x,
+				union ieee754sp y)
+{
+	return _sp_maddf(z, x, y, MADDF_NEGATE_ADDITION);
+}
+
+union ieee754sp ieee754sp_nmadd(union ieee754sp z, union ieee754sp x,
+				union ieee754sp y)
+{
+	return _sp_maddf(z, x, y, MADDF_NEGATE_PRODUCT|MADDF_NEGATE_ADDITION);
+}
+
+union ieee754sp ieee754sp_nmsub(union ieee754sp z, union ieee754sp x,
+				union ieee754sp y)
+{
+	return _sp_maddf(z, x, y, MADDF_NEGATE_PRODUCT);
+}
diff --git a/arch/mips/math-emu/sp_mul.c b/arch/mips/math-emu/sp_mul.c
new file mode 100644
index 000000000..26cfd6302
--- /dev/null
+++ b/arch/mips/math-emu/sp_mul.c
@@ -0,0 +1,154 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* IEEE754 floating point arithmetic
+ * single precision
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ */
+
+#include "ieee754sp.h"
+
+union ieee754sp ieee754sp_mul(union ieee754sp x, union ieee754sp y)
+{
+	int re;
+	int rs;
+	unsigned int rm;
+	unsigned short lxm;
+	unsigned short hxm;
+	unsigned short lym;
+	unsigned short hym;
+	unsigned int lrm;
+	unsigned int hrm;
+	unsigned int t;
+	unsigned int at;
+
+	COMPXSP;
+	COMPYSP;
+
+	EXPLODEXSP;
+	EXPLODEYSP;
+
+	ieee754_clearcx();
+
+	FLUSHXSP;
+	FLUSHYSP;
+
+	switch (CLPAIR(xc, yc)) {
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_SNAN):
+		return ieee754sp_nanxcpt(y);
+
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_INF):
+		return ieee754sp_nanxcpt(x);
+
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_QNAN):
+		return y;
+
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_INF):
+		return x;
+
+
+	/*
+	 * Infinity handling
+	 */
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_INF):
+		ieee754_setcx(IEEE754_INVALID_OPERATION);
+		return ieee754sp_indef();
+
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_INF):
+		return ieee754sp_inf(xs ^ ys);
+
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_ZERO):
+		return ieee754sp_zero(xs ^ ys);
+
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_DNORM):
+		SPDNORMX;
+		fallthrough;
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_DNORM):
+		SPDNORMY;
+		break;
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_NORM):
+		SPDNORMX;
+		break;
+
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_NORM):
+		break;
+	}
+	/* rm = xm * ym, re = xe+ye basically */
+	assert(xm & SP_HIDDEN_BIT);
+	assert(ym & SP_HIDDEN_BIT);
+
+	re = xe + ye;
+	rs = xs ^ ys;
+
+	/* shunt to top of word */
+	xm <<= 32 - (SP_FBITS + 1);
+	ym <<= 32 - (SP_FBITS + 1);
+
+	/*
+	 * Multiply 32 bits xm, ym to give high 32 bits rm with stickness.
+	 */
+	lxm = xm & 0xffff;
+	hxm = xm >> 16;
+	lym = ym & 0xffff;
+	hym = ym >> 16;
+
+	lrm = lxm * lym;	/* 16 * 16 => 32 */
+	hrm = hxm * hym;	/* 16 * 16 => 32 */
+
+	t = lxm * hym; /* 16 * 16 => 32 */
+	at = lrm + (t << 16);
+	hrm += at < lrm;
+	lrm = at;
+	hrm = hrm + (t >> 16);
+
+	t = hxm * lym; /* 16 * 16 => 32 */
+	at = lrm + (t << 16);
+	hrm += at < lrm;
+	lrm = at;
+	hrm = hrm + (t >> 16);
+
+	rm = hrm | (lrm != 0);
+
+	/*
+	 * Sticky shift down to normal rounding precision.
+	 */
+	if ((int) rm < 0) {
+		rm = (rm >> (32 - (SP_FBITS + 1 + 3))) |
+		    ((rm << (SP_FBITS + 1 + 3)) != 0);
+		re++;
+	} else {
+		rm = (rm >> (32 - (SP_FBITS + 1 + 3 + 1))) |
+		     ((rm << (SP_FBITS + 1 + 3 + 1)) != 0);
+	}
+	assert(rm & (SP_HIDDEN_BIT << 3));
+
+	return ieee754sp_format(rs, re, rm);
+}
diff --git a/arch/mips/math-emu/sp_rint.c b/arch/mips/math-emu/sp_rint.c
new file mode 100644
index 000000000..d5f75fe21
--- /dev/null
+++ b/arch/mips/math-emu/sp_rint.c
@@ -0,0 +1,79 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* IEEE754 floating point arithmetic
+ * single precision
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ * Copyright (C) 2017 Imagination Technologies, Ltd.
+ * Author: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
+ */
+
+#include "ieee754sp.h"
+
+union ieee754sp ieee754sp_rint(union ieee754sp x)
+{
+	union ieee754sp ret;
+	u32 residue;
+	int sticky;
+	int round;
+	int odd;
+
+	COMPXDP;		/* <-- DP needed for 64-bit mantissa tmp */
+
+	ieee754_clearcx();
+
+	EXPLODEXSP;
+	FLUSHXSP;
+
+	if (xc == IEEE754_CLASS_SNAN)
+		return ieee754sp_nanxcpt(x);
+
+	if ((xc == IEEE754_CLASS_QNAN) ||
+	    (xc == IEEE754_CLASS_INF) ||
+	    (xc == IEEE754_CLASS_ZERO))
+		return x;
+
+	if (xe >= SP_FBITS)
+		return x;
+
+	if (xe < -1) {
+		residue = xm;
+		round = 0;
+		sticky = residue != 0;
+		xm = 0;
+	} else {
+		residue = xm << (xe + 1);
+		residue <<= 31 - SP_FBITS;
+		round = (residue >> 31) != 0;
+		sticky = (residue << 1) != 0;
+		xm >>= SP_FBITS - xe;
+	}
+
+	odd = (xm & 0x1) != 0x0;
+
+	switch (ieee754_csr.rm) {
+	case FPU_CSR_RN:	/* toward nearest */
+		if (round && (sticky || odd))
+			xm++;
+		break;
+	case FPU_CSR_RZ:	/* toward zero */
+		break;
+	case FPU_CSR_RU:	/* toward +infinity */
+		if ((round || sticky) && !xs)
+			xm++;
+		break;
+	case FPU_CSR_RD:	/* toward -infinity */
+		if ((round || sticky) && xs)
+			xm++;
+		break;
+	}
+
+	if (round || sticky)
+		ieee754_setcx(IEEE754_INEXACT);
+
+	ret = ieee754sp_flong(xm);
+	SPSIGN(ret) = xs;
+
+	return ret;
+}
diff --git a/arch/mips/math-emu/sp_simple.c b/arch/mips/math-emu/sp_simple.c
new file mode 100644
index 000000000..b9e91da7d
--- /dev/null
+++ b/arch/mips/math-emu/sp_simple.c
@@ -0,0 +1,49 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* IEEE754 floating point arithmetic
+ * single precision
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ */
+
+#include "ieee754sp.h"
+
+union ieee754sp ieee754sp_neg(union ieee754sp x)
+{
+	union ieee754sp y;
+
+	if (ieee754_csr.abs2008) {
+		y = x;
+		SPSIGN(y) = !SPSIGN(x);
+	} else {
+		unsigned int oldrm;
+
+		oldrm = ieee754_csr.rm;
+		ieee754_csr.rm = FPU_CSR_RD;
+		y = ieee754sp_sub(ieee754sp_zero(0), x);
+		ieee754_csr.rm = oldrm;
+	}
+	return y;
+}
+
+union ieee754sp ieee754sp_abs(union ieee754sp x)
+{
+	union ieee754sp y;
+
+	if (ieee754_csr.abs2008) {
+		y = x;
+		SPSIGN(y) = 0;
+	} else {
+		unsigned int oldrm;
+
+		oldrm = ieee754_csr.rm;
+		ieee754_csr.rm = FPU_CSR_RD;
+		if (SPSIGN(x))
+			y = ieee754sp_sub(ieee754sp_zero(0), x);
+		else
+			y = ieee754sp_add(ieee754sp_zero(0), x);
+		ieee754_csr.rm = oldrm;
+	}
+	return y;
+}
diff --git a/arch/mips/math-emu/sp_sqrt.c b/arch/mips/math-emu/sp_sqrt.c
new file mode 100644
index 000000000..e9bb60121
--- /dev/null
+++ b/arch/mips/math-emu/sp_sqrt.c
@@ -0,0 +1,103 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* IEEE754 floating point arithmetic
+ * single precision square root
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ */
+
+#include "ieee754sp.h"
+
+union ieee754sp ieee754sp_sqrt(union ieee754sp x)
+{
+	int ix, s, q, m, t, i;
+	unsigned int r;
+	COMPXSP;
+
+	/* take care of Inf and NaN */
+
+	EXPLODEXSP;
+	ieee754_clearcx();
+	FLUSHXSP;
+
+	/* x == INF or NAN? */
+	switch (xc) {
+	case IEEE754_CLASS_SNAN:
+		return ieee754sp_nanxcpt(x);
+
+	case IEEE754_CLASS_QNAN:
+		/* sqrt(Nan) = Nan */
+		return x;
+
+	case IEEE754_CLASS_ZERO:
+		/* sqrt(0) = 0 */
+		return x;
+
+	case IEEE754_CLASS_INF:
+		if (xs) {
+			/* sqrt(-Inf) = Nan */
+			ieee754_setcx(IEEE754_INVALID_OPERATION);
+			return ieee754sp_indef();
+		}
+		/* sqrt(+Inf) = Inf */
+		return x;
+
+	case IEEE754_CLASS_DNORM:
+	case IEEE754_CLASS_NORM:
+		if (xs) {
+			/* sqrt(-x) = Nan */
+			ieee754_setcx(IEEE754_INVALID_OPERATION);
+			return ieee754sp_indef();
+		}
+		break;
+	}
+
+	ix = x.bits;
+
+	/* normalize x */
+	m = (ix >> 23);
+	if (m == 0) {		/* subnormal x */
+		for (i = 0; (ix & 0x00800000) == 0; i++)
+			ix <<= 1;
+		m -= i - 1;
+	}
+	m -= 127;		/* unbias exponent */
+	ix = (ix & 0x007fffff) | 0x00800000;
+	if (m & 1)		/* odd m, double x to make it even */
+		ix += ix;
+	m >>= 1;		/* m = [m/2] */
+
+	/* generate sqrt(x) bit by bit */
+	ix += ix;
+	s = 0;
+	q = 0;			/* q = sqrt(x) */
+	r = 0x01000000;		/* r = moving bit from right to left */
+
+	while (r != 0) {
+		t = s + r;
+		if (t <= ix) {
+			s = t + r;
+			ix -= t;
+			q += r;
+		}
+		ix += ix;
+		r >>= 1;
+	}
+
+	if (ix != 0) {
+		ieee754_setcx(IEEE754_INEXACT);
+		switch (ieee754_csr.rm) {
+		case FPU_CSR_RU:
+			q += 2;
+			break;
+		case FPU_CSR_RN:
+			q += (q & 1);
+			break;
+		}
+	}
+	ix = (q >> 1) + 0x3f000000;
+	ix += (m << 23);
+	x.bits = ix;
+	return x;
+}
diff --git a/arch/mips/math-emu/sp_sub.c b/arch/mips/math-emu/sp_sub.c
new file mode 100644
index 000000000..16c8e9ae6
--- /dev/null
+++ b/arch/mips/math-emu/sp_sub.c
@@ -0,0 +1,168 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* IEEE754 floating point arithmetic
+ * single precision
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ */
+
+#include "ieee754sp.h"
+
+union ieee754sp ieee754sp_sub(union ieee754sp x, union ieee754sp y)
+{
+	int s;
+
+	COMPXSP;
+	COMPYSP;
+
+	EXPLODEXSP;
+	EXPLODEYSP;
+
+	ieee754_clearcx();
+
+	FLUSHXSP;
+	FLUSHYSP;
+
+	switch (CLPAIR(xc, yc)) {
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_SNAN):
+		return ieee754sp_nanxcpt(y);
+
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_SNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_SNAN, IEEE754_CLASS_INF):
+		return ieee754sp_nanxcpt(x);
+
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_QNAN):
+		return y;
+
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_QNAN):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_DNORM):
+	case CLPAIR(IEEE754_CLASS_QNAN, IEEE754_CLASS_INF):
+		return x;
+
+
+	/*
+	 * Infinity handling
+	 */
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_INF):
+		if (xs != ys)
+			return x;
+		ieee754_setcx(IEEE754_INVALID_OPERATION);
+		return ieee754sp_indef();
+
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_INF):
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_INF):
+		return ieee754sp_inf(ys ^ 1);
+
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_INF, IEEE754_CLASS_DNORM):
+		return x;
+
+	/*
+	 * Zero handling
+	 */
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_ZERO):
+		if (xs != ys)
+			return x;
+		else
+			return ieee754sp_zero(ieee754_csr.rm == FPU_CSR_RD);
+
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_ZERO):
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_ZERO):
+		return x;
+
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_NORM):
+	case CLPAIR(IEEE754_CLASS_ZERO, IEEE754_CLASS_DNORM):
+		/* quick fix up */
+		SPSIGN(y) ^= 1;
+		return y;
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_DNORM):
+		SPDNORMX;
+		fallthrough;
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_DNORM):
+		SPDNORMY;
+		break;
+
+	case CLPAIR(IEEE754_CLASS_DNORM, IEEE754_CLASS_NORM):
+		SPDNORMX;
+		break;
+
+	case CLPAIR(IEEE754_CLASS_NORM, IEEE754_CLASS_NORM):
+		break;
+	}
+	/* flip sign of y and handle as add */
+	ys ^= 1;
+
+	assert(xm & SP_HIDDEN_BIT);
+	assert(ym & SP_HIDDEN_BIT);
+
+
+	/* provide guard,round and stick bit space */
+	xm <<= 3;
+	ym <<= 3;
+
+	if (xe > ye) {
+		/*
+		 * have to shift y fraction right to align
+		 */
+		s = xe - ye;
+		ym = XSPSRS(ym, s);
+		ye += s;
+	} else if (ye > xe) {
+		/*
+		 * have to shift x fraction right to align
+		 */
+		s = ye - xe;
+		xm = XSPSRS(xm, s);
+		xe += s;
+	}
+	assert(xe == ye);
+	assert(xe <= SP_EMAX);
+
+	if (xs == ys) {
+		/* generate 28 bit result of adding two 27 bit numbers
+		 */
+		xm = xm + ym;
+
+		if (xm >> (SP_FBITS + 1 + 3)) { /* carry out */
+			SPXSRSX1();	/* shift preserving sticky */
+		}
+	} else {
+		if (xm >= ym) {
+			xm = xm - ym;
+		} else {
+			xm = ym - xm;
+			xs = ys;
+		}
+		if (xm == 0) {
+			if (ieee754_csr.rm == FPU_CSR_RD)
+				return ieee754sp_zero(1);	/* round negative inf. => sign = -1 */
+			else
+				return ieee754sp_zero(0);	/* other round modes   => sign = 1 */
+		}
+		/* normalize to rounding precision
+		 */
+		while ((xm >> (SP_FBITS + 3)) == 0) {
+			xm <<= 1;
+			xe--;
+		}
+	}
+
+	return ieee754sp_format(xs, xe, xm);
+}
diff --git a/arch/mips/math-emu/sp_tint.c b/arch/mips/math-emu/sp_tint.c
new file mode 100644
index 000000000..f7a5cf5e1
--- /dev/null
+++ b/arch/mips/math-emu/sp_tint.c
@@ -0,0 +1,100 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* IEEE754 floating point arithmetic
+ * single precision
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ */
+
+#include "ieee754sp.h"
+
+int ieee754sp_tint(union ieee754sp x)
+{
+	u32 residue;
+	int round;
+	int sticky;
+	int odd;
+
+	COMPXSP;
+
+	ieee754_clearcx();
+
+	EXPLODEXSP;
+	FLUSHXSP;
+
+	switch (xc) {
+	case IEEE754_CLASS_SNAN:
+	case IEEE754_CLASS_QNAN:
+		ieee754_setcx(IEEE754_INVALID_OPERATION);
+		return ieee754si_indef();
+
+	case IEEE754_CLASS_INF:
+		ieee754_setcx(IEEE754_INVALID_OPERATION);
+		return ieee754si_overflow(xs);
+
+	case IEEE754_CLASS_ZERO:
+		return 0;
+
+	case IEEE754_CLASS_DNORM:
+	case IEEE754_CLASS_NORM:
+		break;
+	}
+	if (xe >= 31) {
+		/* look for valid corner case */
+		if (xe == 31 && xs && xm == SP_HIDDEN_BIT)
+			return -0x80000000;
+		/* Set invalid. We will only use overflow for floating
+		   point overflow */
+		ieee754_setcx(IEEE754_INVALID_OPERATION);
+		return ieee754si_overflow(xs);
+	}
+	/* oh gawd */
+	if (xe > SP_FBITS) {
+		xm <<= xe - SP_FBITS;
+	} else {
+		if (xe < -1) {
+			residue = xm;
+			round = 0;
+			sticky = residue != 0;
+			xm = 0;
+		} else {
+			/* Shifting a u32 32 times does not work,
+			* so we do it in two steps. Be aware that xe
+			* may be -1 */
+			residue = xm << (xe + 1);
+			residue <<= 31 - SP_FBITS;
+			round = (residue >> 31) != 0;
+			sticky = (residue << 1) != 0;
+			xm >>= SP_FBITS - xe;
+		}
+		odd = (xm & 0x1) != 0x0;
+		switch (ieee754_csr.rm) {
+		case FPU_CSR_RN:
+			if (round && (sticky || odd))
+				xm++;
+			break;
+		case FPU_CSR_RZ:
+			break;
+		case FPU_CSR_RU:	/* toward +Infinity */
+			if ((round || sticky) && !xs)
+				xm++;
+			break;
+		case FPU_CSR_RD:	/* toward -Infinity */
+			if ((round || sticky) && xs)
+				xm++;
+			break;
+		}
+		if ((xm >> 31) != 0) {
+			/* This can happen after rounding */
+			ieee754_setcx(IEEE754_INVALID_OPERATION);
+			return ieee754si_overflow(xs);
+		}
+		if (round || sticky)
+			ieee754_setcx(IEEE754_INEXACT);
+	}
+	if (xs)
+		return -xm;
+	else
+		return xm;
+}
diff --git a/arch/mips/math-emu/sp_tlong.c b/arch/mips/math-emu/sp_tlong.c
new file mode 100644
index 000000000..adc191304
--- /dev/null
+++ b/arch/mips/math-emu/sp_tlong.c
@@ -0,0 +1,96 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* IEEE754 floating point arithmetic
+ * single precision
+ */
+/*
+ * MIPS floating point support
+ * Copyright (C) 1994-2000 Algorithmics Ltd.
+ */
+
+#include "ieee754sp.h"
+
+s64 ieee754sp_tlong(union ieee754sp x)
+{
+	u32 residue;
+	int round;
+	int sticky;
+	int odd;
+
+	COMPXDP;		/* <-- need 64-bit mantissa tmp */
+
+	ieee754_clearcx();
+
+	EXPLODEXSP;
+	FLUSHXSP;
+
+	switch (xc) {
+	case IEEE754_CLASS_SNAN:
+	case IEEE754_CLASS_QNAN:
+		ieee754_setcx(IEEE754_INVALID_OPERATION);
+		return ieee754di_indef();
+
+	case IEEE754_CLASS_INF:
+		ieee754_setcx(IEEE754_INVALID_OPERATION);
+		return ieee754di_overflow(xs);
+
+	case IEEE754_CLASS_ZERO:
+		return 0;
+
+	case IEEE754_CLASS_DNORM:
+	case IEEE754_CLASS_NORM:
+		break;
+	}
+	if (xe >= 63) {
+		/* look for valid corner case */
+		if (xe == 63 && xs && xm == SP_HIDDEN_BIT)
+			return -0x8000000000000000LL;
+		/* Set invalid. We will only use overflow for floating
+		   point overflow */
+		ieee754_setcx(IEEE754_INVALID_OPERATION);
+		return ieee754di_overflow(xs);
+	}
+	/* oh gawd */
+	if (xe > SP_FBITS) {
+		xm <<= xe - SP_FBITS;
+	} else if (xe < SP_FBITS) {
+		if (xe < -1) {
+			residue = xm;
+			round = 0;
+			sticky = residue != 0;
+			xm = 0;
+		} else {
+			residue = xm << (32 - SP_FBITS + xe);
+			round = (residue >> 31) != 0;
+			sticky = (residue << 1) != 0;
+			xm >>= SP_FBITS - xe;
+		}
+		odd = (xm & 0x1) != 0x0;
+		switch (ieee754_csr.rm) {
+		case FPU_CSR_RN:
+			if (round && (sticky || odd))
+				xm++;
+			break;
+		case FPU_CSR_RZ:
+			break;
+		case FPU_CSR_RU:	/* toward +Infinity */
+			if ((round || sticky) && !xs)
+				xm++;
+			break;
+		case FPU_CSR_RD:	/* toward -Infinity */
+			if ((round || sticky) && xs)
+				xm++;
+			break;
+		}
+		if ((xm >> 63) != 0) {
+			/* This can happen after rounding */
+			ieee754_setcx(IEEE754_INVALID_OPERATION);
+			return ieee754di_overflow(xs);
+		}
+		if (round || sticky)
+			ieee754_setcx(IEEE754_INEXACT);
+	}
+	if (xs)
+		return -xm;
+	else
+		return xm;
+}
diff --git a/arch/mips/mm/Makefile b/arch/mips/mm/Makefile
new file mode 100644
index 000000000..304692391
--- /dev/null
+++ b/arch/mips/mm/Makefile
@@ -0,0 +1,47 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Makefile for the Linux/MIPS-specific parts of the memory manager.
+#
+
+obj-y				+= cache.o
+obj-y				+= context.o
+obj-y				+= extable.o
+obj-y				+= fault.o
+obj-y				+= init.o
+obj-y				+= mmap.o
+obj-y				+= page.o
+obj-y				+= page-funcs.o
+obj-y				+= pgtable.o
+obj-y				+= tlbex.o
+obj-y				+= tlbex-fault.o
+obj-y				+= tlb-funcs.o
+
+ifdef CONFIG_CPU_MICROMIPS
+obj-y				+= uasm-micromips.o
+else
+obj-y				+= uasm-mips.o
+endif
+
+ifndef CONFIG_EVA
+obj-y				+= maccess.o
+endif
+
+obj-$(CONFIG_32BIT)		+= ioremap.o pgtable-32.o
+obj-$(CONFIG_64BIT)		+= ioremap64.o pgtable-64.o
+obj-$(CONFIG_HIGHMEM)		+= highmem.o
+obj-$(CONFIG_HUGETLB_PAGE)	+= hugetlbpage.o
+obj-$(CONFIG_DMA_NONCOHERENT)	+= dma-noncoherent.o
+
+obj-$(CONFIG_CPU_R3K_TLB)	+= tlb-r3k.o
+obj-$(CONFIG_CPU_R4K_CACHE_TLB) += c-r4k.o cex-gen.o tlb-r4k.o
+obj-$(CONFIG_CPU_R3000)		+= c-r3k.o
+obj-$(CONFIG_CPU_SB1)		+= c-r4k.o cerr-sb1.o cex-sb1.o tlb-r4k.o
+obj-$(CONFIG_CPU_CAVIUM_OCTEON) += c-octeon.o cex-oct.o tlb-r4k.o
+
+obj-$(CONFIG_IP22_CPU_SCACHE)	+= sc-ip22.o
+obj-$(CONFIG_R5000_CPU_SCACHE)	+= sc-r5k.o
+obj-$(CONFIG_RM7000_CPU_SCACHE) += sc-rm7k.o
+obj-$(CONFIG_MIPS_CPU_SCACHE)	+= sc-mips.o
+obj-$(CONFIG_SCACHE_DEBUGFS)	+= sc-debugfs.o
+
+obj-$(CONFIG_DEBUG_VIRTUAL)	+= physaddr.o
diff --git a/arch/mips/mm/c-octeon.c b/arch/mips/mm/c-octeon.c
new file mode 100644
index 000000000..c7ed589de
--- /dev/null
+++ b/arch/mips/mm/c-octeon.c
@@ -0,0 +1,350 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2005-2007 Cavium Networks
+ */
+#include <linux/export.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/smp.h>
+#include <linux/mm.h>
+#include <linux/bitops.h>
+#include <linux/cpu.h>
+#include <linux/io.h>
+
+#include <asm/bcache.h>
+#include <asm/bootinfo.h>
+#include <asm/cacheops.h>
+#include <asm/cpu-features.h>
+#include <asm/cpu-type.h>
+#include <asm/page.h>
+#include <asm/r4kcache.h>
+#include <asm/traps.h>
+#include <asm/mmu_context.h>
+
+#include <asm/octeon/octeon.h>
+
+unsigned long long cache_err_dcache[NR_CPUS];
+EXPORT_SYMBOL_GPL(cache_err_dcache);
+
+/*
+ * Octeon automatically flushes the dcache on tlb changes, so
+ * from Linux's viewpoint it acts much like a physically
+ * tagged cache. No flushing is needed
+ *
+ */
+static void octeon_flush_data_cache_page(unsigned long addr)
+{
+    /* Nothing to do */
+}
+
+static inline void octeon_local_flush_icache(void)
+{
+	asm volatile ("synci 0($0)");
+}
+
+/*
+ * Flush local I-cache for the specified range.
+ */
+static void local_octeon_flush_icache_range(unsigned long start,
+					    unsigned long end)
+{
+	octeon_local_flush_icache();
+}
+
+/**
+ * octeon_flush_icache_all_cores -  Flush caches as necessary for all cores
+ * affected by a vma. If no vma is supplied, all cores are flushed.
+ *
+ * @vma:    VMA to flush or NULL to flush all icaches.
+ */
+static void octeon_flush_icache_all_cores(struct vm_area_struct *vma)
+{
+	extern void octeon_send_ipi_single(int cpu, unsigned int action);
+#ifdef CONFIG_SMP
+	int cpu;
+	cpumask_t mask;
+#endif
+
+	mb();
+	octeon_local_flush_icache();
+#ifdef CONFIG_SMP
+	preempt_disable();
+	cpu = smp_processor_id();
+
+	/*
+	 * If we have a vma structure, we only need to worry about
+	 * cores it has been used on
+	 */
+	if (vma)
+		mask = *mm_cpumask(vma->vm_mm);
+	else
+		mask = *cpu_online_mask;
+	cpumask_clear_cpu(cpu, &mask);
+	for_each_cpu(cpu, &mask)
+		octeon_send_ipi_single(cpu, SMP_ICACHE_FLUSH);
+
+	preempt_enable();
+#endif
+}
+
+
+/*
+ * Called to flush the icache on all cores
+ */
+static void octeon_flush_icache_all(void)
+{
+	octeon_flush_icache_all_cores(NULL);
+}
+
+
+/**
+ * octeon_flush_cache_mm - flush all memory associated with a memory context.
+ *
+ * @mm:	    Memory context to flush
+ */
+static void octeon_flush_cache_mm(struct mm_struct *mm)
+{
+	/*
+	 * According to the R4K version of this file, CPUs without
+	 * dcache aliases don't need to do anything here
+	 */
+}
+
+
+/*
+ * Flush a range of kernel addresses out of the icache
+ *
+ */
+static void octeon_flush_icache_range(unsigned long start, unsigned long end)
+{
+	octeon_flush_icache_all_cores(NULL);
+}
+
+
+/**
+ * octeon_flush_cache_range - Flush a range out of a vma
+ *
+ * @vma:    VMA to flush
+ * @start:  beginning address for flush
+ * @end:    ending address for flush
+ */
+static void octeon_flush_cache_range(struct vm_area_struct *vma,
+				     unsigned long start, unsigned long end)
+{
+	if (vma->vm_flags & VM_EXEC)
+		octeon_flush_icache_all_cores(vma);
+}
+
+
+/**
+ * octeon_flush_cache_page - Flush a specific page of a vma
+ *
+ * @vma:    VMA to flush page for
+ * @page:   Page to flush
+ * @pfn:    Page frame number
+ */
+static void octeon_flush_cache_page(struct vm_area_struct *vma,
+				    unsigned long page, unsigned long pfn)
+{
+	if (vma->vm_flags & VM_EXEC)
+		octeon_flush_icache_all_cores(vma);
+}
+
+static void octeon_flush_kernel_vmap_range(unsigned long vaddr, int size)
+{
+	BUG();
+}
+
+/*
+ * Probe Octeon's caches
+ *
+ */
+static void probe_octeon(void)
+{
+	unsigned long icache_size;
+	unsigned long dcache_size;
+	unsigned int config1;
+	struct cpuinfo_mips *c = &current_cpu_data;
+	int cputype = current_cpu_type();
+
+	config1 = read_c0_config1();
+	switch (cputype) {
+	case CPU_CAVIUM_OCTEON:
+	case CPU_CAVIUM_OCTEON_PLUS:
+		c->icache.linesz = 2 << ((config1 >> 19) & 7);
+		c->icache.sets = 64 << ((config1 >> 22) & 7);
+		c->icache.ways = 1 + ((config1 >> 16) & 7);
+		c->icache.flags |= MIPS_CACHE_VTAG;
+		icache_size =
+			c->icache.sets * c->icache.ways * c->icache.linesz;
+		c->icache.waybit = ffs(icache_size / c->icache.ways) - 1;
+		c->dcache.linesz = 128;
+		if (cputype == CPU_CAVIUM_OCTEON_PLUS)
+			c->dcache.sets = 2; /* CN5XXX has two Dcache sets */
+		else
+			c->dcache.sets = 1; /* CN3XXX has one Dcache set */
+		c->dcache.ways = 64;
+		dcache_size =
+			c->dcache.sets * c->dcache.ways * c->dcache.linesz;
+		c->dcache.waybit = ffs(dcache_size / c->dcache.ways) - 1;
+		c->options |= MIPS_CPU_PREFETCH;
+		break;
+
+	case CPU_CAVIUM_OCTEON2:
+		c->icache.linesz = 2 << ((config1 >> 19) & 7);
+		c->icache.sets = 8;
+		c->icache.ways = 37;
+		c->icache.flags |= MIPS_CACHE_VTAG;
+		icache_size = c->icache.sets * c->icache.ways * c->icache.linesz;
+
+		c->dcache.linesz = 128;
+		c->dcache.ways = 32;
+		c->dcache.sets = 8;
+		dcache_size = c->dcache.sets * c->dcache.ways * c->dcache.linesz;
+		c->options |= MIPS_CPU_PREFETCH;
+		break;
+
+	case CPU_CAVIUM_OCTEON3:
+		c->icache.linesz = 128;
+		c->icache.sets = 16;
+		c->icache.ways = 39;
+		c->icache.flags |= MIPS_CACHE_VTAG;
+		icache_size = c->icache.sets * c->icache.ways * c->icache.linesz;
+
+		c->dcache.linesz = 128;
+		c->dcache.ways = 32;
+		c->dcache.sets = 8;
+		dcache_size = c->dcache.sets * c->dcache.ways * c->dcache.linesz;
+		c->options |= MIPS_CPU_PREFETCH;
+		break;
+
+	default:
+		panic("Unsupported Cavium Networks CPU type");
+		break;
+	}
+
+	/* compute a couple of other cache variables */
+	c->icache.waysize = icache_size / c->icache.ways;
+	c->dcache.waysize = dcache_size / c->dcache.ways;
+
+	c->icache.sets = icache_size / (c->icache.linesz * c->icache.ways);
+	c->dcache.sets = dcache_size / (c->dcache.linesz * c->dcache.ways);
+
+	if (smp_processor_id() == 0) {
+		pr_info("Primary instruction cache %ldkB, %s, %d way, "
+			"%d sets, linesize %d bytes.\n",
+			icache_size >> 10,
+			cpu_has_vtag_icache ?
+				"virtually tagged" : "physically tagged",
+			c->icache.ways, c->icache.sets, c->icache.linesz);
+
+		pr_info("Primary data cache %ldkB, %d-way, %d sets, "
+			"linesize %d bytes.\n",
+			dcache_size >> 10, c->dcache.ways,
+			c->dcache.sets, c->dcache.linesz);
+	}
+}
+
+static void  octeon_cache_error_setup(void)
+{
+	extern char except_vec2_octeon;
+	set_handler(0x100, &except_vec2_octeon, 0x80);
+}
+
+/*
+ * Setup the Octeon cache flush routines
+ *
+ */
+void octeon_cache_init(void)
+{
+	probe_octeon();
+
+	shm_align_mask = PAGE_SIZE - 1;
+
+	flush_cache_all			= octeon_flush_icache_all;
+	__flush_cache_all		= octeon_flush_icache_all;
+	flush_cache_mm			= octeon_flush_cache_mm;
+	flush_cache_page		= octeon_flush_cache_page;
+	flush_cache_range		= octeon_flush_cache_range;
+	flush_icache_all		= octeon_flush_icache_all;
+	flush_data_cache_page		= octeon_flush_data_cache_page;
+	flush_icache_range		= octeon_flush_icache_range;
+	local_flush_icache_range	= local_octeon_flush_icache_range;
+	__flush_icache_user_range	= octeon_flush_icache_range;
+	__local_flush_icache_user_range	= local_octeon_flush_icache_range;
+
+	__flush_kernel_vmap_range	= octeon_flush_kernel_vmap_range;
+
+	build_clear_page();
+	build_copy_page();
+
+	board_cache_error_setup = octeon_cache_error_setup;
+}
+
+/*
+ * Handle a cache error exception
+ */
+static RAW_NOTIFIER_HEAD(co_cache_error_chain);
+
+int register_co_cache_error_notifier(struct notifier_block *nb)
+{
+	return raw_notifier_chain_register(&co_cache_error_chain, nb);
+}
+EXPORT_SYMBOL_GPL(register_co_cache_error_notifier);
+
+int unregister_co_cache_error_notifier(struct notifier_block *nb)
+{
+	return raw_notifier_chain_unregister(&co_cache_error_chain, nb);
+}
+EXPORT_SYMBOL_GPL(unregister_co_cache_error_notifier);
+
+static void co_cache_error_call_notifiers(unsigned long val)
+{
+	int rv = raw_notifier_call_chain(&co_cache_error_chain, val, NULL);
+	if ((rv & ~NOTIFY_STOP_MASK) != NOTIFY_OK) {
+		u64 dcache_err;
+		unsigned long coreid = cvmx_get_core_num();
+		u64 icache_err = read_octeon_c0_icacheerr();
+
+		if (val) {
+			dcache_err = cache_err_dcache[coreid];
+			cache_err_dcache[coreid] = 0;
+		} else {
+			dcache_err = read_octeon_c0_dcacheerr();
+		}
+
+		pr_err("Core%lu: Cache error exception:\n", coreid);
+		pr_err("cp0_errorepc == %lx\n", read_c0_errorepc());
+		if (icache_err & 1) {
+			pr_err("CacheErr (Icache) == %llx\n",
+			       (unsigned long long)icache_err);
+			write_octeon_c0_icacheerr(0);
+		}
+		if (dcache_err & 1) {
+			pr_err("CacheErr (Dcache) == %llx\n",
+			       (unsigned long long)dcache_err);
+		}
+	}
+}
+
+/*
+ * Called when the exception is recoverable
+ */
+
+asmlinkage void cache_parity_error_octeon_recoverable(void)
+{
+	co_cache_error_call_notifiers(0);
+}
+
+/*
+ * Called when the exception is not recoverable
+ */
+
+asmlinkage void cache_parity_error_octeon_non_recoverable(void)
+{
+	co_cache_error_call_notifiers(1);
+	panic("Can't handle cache error: nested exception");
+}
diff --git a/arch/mips/mm/c-r3k.c b/arch/mips/mm/c-r3k.c
new file mode 100644
index 000000000..df6755ca1
--- /dev/null
+++ b/arch/mips/mm/c-r3k.c
@@ -0,0 +1,319 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * r2300.c: R2000 and R3000 specific mmu/cache code.
+ *
+ * Copyright (C) 1996 David S. Miller (davem@davemloft.net)
+ *
+ * with a lot of changes to make this thing work for R3000s
+ * Tx39XX R4k style caches added. HK
+ * Copyright (C) 1998, 1999, 2000 Harald Koerfgen
+ * Copyright (C) 1998 Gleb Raiko & Vladimir Roganov
+ * Copyright (C) 2001, 2004, 2007  Maciej W. Rozycki
+ */
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/smp.h>
+#include <linux/mm.h>
+
+#include <asm/page.h>
+#include <asm/mmu_context.h>
+#include <asm/isadep.h>
+#include <asm/io.h>
+#include <asm/bootinfo.h>
+#include <asm/cpu.h>
+
+static unsigned long icache_size, dcache_size;		/* Size in bytes */
+static unsigned long icache_lsize, dcache_lsize;	/* Size in bytes */
+
+unsigned long r3k_cache_size(unsigned long ca_flags)
+{
+	unsigned long flags, status, dummy, size;
+	volatile unsigned long *p;
+
+	p = (volatile unsigned long *) KSEG0;
+
+	flags = read_c0_status();
+
+	/* isolate cache space */
+	write_c0_status((ca_flags|flags)&~ST0_IEC);
+
+	*p = 0xa5a55a5a;
+	dummy = *p;
+	status = read_c0_status();
+
+	if (dummy != 0xa5a55a5a || (status & ST0_CM)) {
+		size = 0;
+	} else {
+		for (size = 128; size <= 0x40000; size <<= 1)
+			*(p + size) = 0;
+		*p = -1;
+		for (size = 128;
+		     (size <= 0x40000) && (*(p + size) == 0);
+		     size <<= 1)
+			;
+		if (size > 0x40000)
+			size = 0;
+	}
+
+	write_c0_status(flags);
+
+	return size * sizeof(*p);
+}
+
+unsigned long r3k_cache_lsize(unsigned long ca_flags)
+{
+	unsigned long flags, status, lsize, i;
+	volatile unsigned long *p;
+
+	p = (volatile unsigned long *) KSEG0;
+
+	flags = read_c0_status();
+
+	/* isolate cache space */
+	write_c0_status((ca_flags|flags)&~ST0_IEC);
+
+	for (i = 0; i < 128; i++)
+		*(p + i) = 0;
+	*(volatile unsigned char *)p = 0;
+	for (lsize = 1; lsize < 128; lsize <<= 1) {
+		*(p + lsize);
+		status = read_c0_status();
+		if (!(status & ST0_CM))
+			break;
+	}
+	for (i = 0; i < 128; i += lsize)
+		*(volatile unsigned char *)(p + i) = 0;
+
+	write_c0_status(flags);
+
+	return lsize * sizeof(*p);
+}
+
+static void r3k_probe_cache(void)
+{
+	dcache_size = r3k_cache_size(ST0_ISC);
+	if (dcache_size)
+		dcache_lsize = r3k_cache_lsize(ST0_ISC);
+
+	icache_size = r3k_cache_size(ST0_ISC|ST0_SWC);
+	if (icache_size)
+		icache_lsize = r3k_cache_lsize(ST0_ISC|ST0_SWC);
+}
+
+static void r3k_flush_icache_range(unsigned long start, unsigned long end)
+{
+	unsigned long size, i, flags;
+	volatile unsigned char *p;
+
+	size = end - start;
+	if (size > icache_size || KSEGX(start) != KSEG0) {
+		start = KSEG0;
+		size = icache_size;
+	}
+	p = (char *)start;
+
+	flags = read_c0_status();
+
+	/* isolate cache space */
+	write_c0_status((ST0_ISC|ST0_SWC|flags)&~ST0_IEC);
+
+	for (i = 0; i < size; i += 0x080) {
+		asm(	"sb\t$0, 0x000(%0)\n\t"
+			"sb\t$0, 0x004(%0)\n\t"
+			"sb\t$0, 0x008(%0)\n\t"
+			"sb\t$0, 0x00c(%0)\n\t"
+			"sb\t$0, 0x010(%0)\n\t"
+			"sb\t$0, 0x014(%0)\n\t"
+			"sb\t$0, 0x018(%0)\n\t"
+			"sb\t$0, 0x01c(%0)\n\t"
+			"sb\t$0, 0x020(%0)\n\t"
+			"sb\t$0, 0x024(%0)\n\t"
+			"sb\t$0, 0x028(%0)\n\t"
+			"sb\t$0, 0x02c(%0)\n\t"
+			"sb\t$0, 0x030(%0)\n\t"
+			"sb\t$0, 0x034(%0)\n\t"
+			"sb\t$0, 0x038(%0)\n\t"
+			"sb\t$0, 0x03c(%0)\n\t"
+			"sb\t$0, 0x040(%0)\n\t"
+			"sb\t$0, 0x044(%0)\n\t"
+			"sb\t$0, 0x048(%0)\n\t"
+			"sb\t$0, 0x04c(%0)\n\t"
+			"sb\t$0, 0x050(%0)\n\t"
+			"sb\t$0, 0x054(%0)\n\t"
+			"sb\t$0, 0x058(%0)\n\t"
+			"sb\t$0, 0x05c(%0)\n\t"
+			"sb\t$0, 0x060(%0)\n\t"
+			"sb\t$0, 0x064(%0)\n\t"
+			"sb\t$0, 0x068(%0)\n\t"
+			"sb\t$0, 0x06c(%0)\n\t"
+			"sb\t$0, 0x070(%0)\n\t"
+			"sb\t$0, 0x074(%0)\n\t"
+			"sb\t$0, 0x078(%0)\n\t"
+			"sb\t$0, 0x07c(%0)\n\t"
+			: : "r" (p) );
+		p += 0x080;
+	}
+
+	write_c0_status(flags);
+}
+
+static void r3k_flush_dcache_range(unsigned long start, unsigned long end)
+{
+	unsigned long size, i, flags;
+	volatile unsigned char *p;
+
+	size = end - start;
+	if (size > dcache_size || KSEGX(start) != KSEG0) {
+		start = KSEG0;
+		size = dcache_size;
+	}
+	p = (char *)start;
+
+	flags = read_c0_status();
+
+	/* isolate cache space */
+	write_c0_status((ST0_ISC|flags)&~ST0_IEC);
+
+	for (i = 0; i < size; i += 0x080) {
+		asm(	"sb\t$0, 0x000(%0)\n\t"
+			"sb\t$0, 0x004(%0)\n\t"
+			"sb\t$0, 0x008(%0)\n\t"
+			"sb\t$0, 0x00c(%0)\n\t"
+			"sb\t$0, 0x010(%0)\n\t"
+			"sb\t$0, 0x014(%0)\n\t"
+			"sb\t$0, 0x018(%0)\n\t"
+			"sb\t$0, 0x01c(%0)\n\t"
+			"sb\t$0, 0x020(%0)\n\t"
+			"sb\t$0, 0x024(%0)\n\t"
+			"sb\t$0, 0x028(%0)\n\t"
+			"sb\t$0, 0x02c(%0)\n\t"
+			"sb\t$0, 0x030(%0)\n\t"
+			"sb\t$0, 0x034(%0)\n\t"
+			"sb\t$0, 0x038(%0)\n\t"
+			"sb\t$0, 0x03c(%0)\n\t"
+			"sb\t$0, 0x040(%0)\n\t"
+			"sb\t$0, 0x044(%0)\n\t"
+			"sb\t$0, 0x048(%0)\n\t"
+			"sb\t$0, 0x04c(%0)\n\t"
+			"sb\t$0, 0x050(%0)\n\t"
+			"sb\t$0, 0x054(%0)\n\t"
+			"sb\t$0, 0x058(%0)\n\t"
+			"sb\t$0, 0x05c(%0)\n\t"
+			"sb\t$0, 0x060(%0)\n\t"
+			"sb\t$0, 0x064(%0)\n\t"
+			"sb\t$0, 0x068(%0)\n\t"
+			"sb\t$0, 0x06c(%0)\n\t"
+			"sb\t$0, 0x070(%0)\n\t"
+			"sb\t$0, 0x074(%0)\n\t"
+			"sb\t$0, 0x078(%0)\n\t"
+			"sb\t$0, 0x07c(%0)\n\t"
+			: : "r" (p) );
+		p += 0x080;
+	}
+
+	write_c0_status(flags);
+}
+
+static inline void r3k_flush_cache_all(void)
+{
+}
+
+static inline void r3k___flush_cache_all(void)
+{
+	r3k_flush_dcache_range(KSEG0, KSEG0 + dcache_size);
+	r3k_flush_icache_range(KSEG0, KSEG0 + icache_size);
+}
+
+static void r3k_flush_cache_mm(struct mm_struct *mm)
+{
+}
+
+static void r3k_flush_cache_range(struct vm_area_struct *vma,
+				  unsigned long start, unsigned long end)
+{
+}
+
+static void r3k_flush_cache_page(struct vm_area_struct *vma,
+				 unsigned long addr, unsigned long pfn)
+{
+	unsigned long kaddr = KSEG0ADDR(pfn << PAGE_SHIFT);
+	int exec = vma->vm_flags & VM_EXEC;
+	struct mm_struct *mm = vma->vm_mm;
+	pmd_t *pmdp;
+	pte_t *ptep;
+
+	pr_debug("cpage[%08llx,%08lx]\n",
+		 cpu_context(smp_processor_id(), mm), addr);
+
+	/* No ASID => no such page in the cache.  */
+	if (cpu_context(smp_processor_id(), mm) == 0)
+		return;
+
+	pmdp = pmd_off(mm, addr);
+	ptep = pte_offset_kernel(pmdp, addr);
+
+	/* Invalid => no such page in the cache.  */
+	if (!(pte_val(*ptep) & _PAGE_PRESENT))
+		return;
+
+	r3k_flush_dcache_range(kaddr, kaddr + PAGE_SIZE);
+	if (exec)
+		r3k_flush_icache_range(kaddr, kaddr + PAGE_SIZE);
+}
+
+static void local_r3k_flush_data_cache_page(void *addr)
+{
+}
+
+static void r3k_flush_data_cache_page(unsigned long addr)
+{
+}
+
+static void r3k_flush_kernel_vmap_range(unsigned long vaddr, int size)
+{
+	BUG();
+}
+
+static void r3k_dma_cache_wback_inv(unsigned long start, unsigned long size)
+{
+	/* Catch bad driver code */
+	BUG_ON(size == 0);
+
+	iob();
+	r3k_flush_dcache_range(start, start + size);
+}
+
+void r3k_cache_init(void)
+{
+	extern void build_clear_page(void);
+	extern void build_copy_page(void);
+
+	r3k_probe_cache();
+
+	flush_cache_all = r3k_flush_cache_all;
+	__flush_cache_all = r3k___flush_cache_all;
+	flush_cache_mm = r3k_flush_cache_mm;
+	flush_cache_range = r3k_flush_cache_range;
+	flush_cache_page = r3k_flush_cache_page;
+	flush_icache_range = r3k_flush_icache_range;
+	local_flush_icache_range = r3k_flush_icache_range;
+	__flush_icache_user_range = r3k_flush_icache_range;
+	__local_flush_icache_user_range = r3k_flush_icache_range;
+
+	__flush_kernel_vmap_range = r3k_flush_kernel_vmap_range;
+
+	local_flush_data_cache_page = local_r3k_flush_data_cache_page;
+	flush_data_cache_page = r3k_flush_data_cache_page;
+
+	_dma_cache_wback_inv = r3k_dma_cache_wback_inv;
+	_dma_cache_wback = r3k_dma_cache_wback_inv;
+	_dma_cache_inv = r3k_dma_cache_wback_inv;
+
+	pr_info("Primary instruction cache %ldkB, linesize %ld bytes.\n",
+		icache_size >> 10, icache_lsize);
+	pr_info("Primary data cache %ldkB, linesize %ld bytes.\n",
+		dcache_size >> 10, dcache_lsize);
+
+	build_clear_page();
+	build_copy_page();
+}
diff --git a/arch/mips/mm/c-r4k.c b/arch/mips/mm/c-r4k.c
new file mode 100644
index 000000000..a549fa98c
--- /dev/null
+++ b/arch/mips/mm/c-r4k.c
@@ -0,0 +1,1957 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1996 David S. Miller (davem@davemloft.net)
+ * Copyright (C) 1997, 1998, 1999, 2000, 2001, 2002 Ralf Baechle (ralf@gnu.org)
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ */
+#include <linux/cpu_pm.h>
+#include <linux/hardirq.h>
+#include <linux/init.h>
+#include <linux/highmem.h>
+#include <linux/kernel.h>
+#include <linux/linkage.h>
+#include <linux/preempt.h>
+#include <linux/sched.h>
+#include <linux/smp.h>
+#include <linux/mm.h>
+#include <linux/export.h>
+#include <linux/bitops.h>
+#include <linux/dma-map-ops.h> /* for dma_default_coherent */
+
+#include <asm/bcache.h>
+#include <asm/bootinfo.h>
+#include <asm/cache.h>
+#include <asm/cacheops.h>
+#include <asm/cpu.h>
+#include <asm/cpu-features.h>
+#include <asm/cpu-type.h>
+#include <asm/io.h>
+#include <asm/page.h>
+#include <asm/r4kcache.h>
+#include <asm/sections.h>
+#include <asm/mmu_context.h>
+#include <asm/cacheflush.h> /* for run_uncached() */
+#include <asm/traps.h>
+#include <asm/mips-cps.h>
+
+/*
+ * Bits describing what cache ops an SMP callback function may perform.
+ *
+ * R4K_HIT   -	Virtual user or kernel address based cache operations. The
+ *		active_mm must be checked before using user addresses, falling
+ *		back to kmap.
+ * R4K_INDEX -	Index based cache operations.
+ */
+
+#define R4K_HIT		BIT(0)
+#define R4K_INDEX	BIT(1)
+
+/**
+ * r4k_op_needs_ipi() - Decide if a cache op needs to be done on every core.
+ * @type:	Type of cache operations (R4K_HIT or R4K_INDEX).
+ *
+ * Decides whether a cache op needs to be performed on every core in the system.
+ * This may change depending on the @type of cache operation, as well as the set
+ * of online CPUs, so preemption should be disabled by the caller to prevent CPU
+ * hotplug from changing the result.
+ *
+ * Returns:	1 if the cache operation @type should be done on every core in
+ *		the system.
+ *		0 if the cache operation @type is globalized and only needs to
+ *		be performed on a simple CPU.
+ */
+static inline bool r4k_op_needs_ipi(unsigned int type)
+{
+	/* The MIPS Coherence Manager (CM) globalizes address-based cache ops */
+	if (type == R4K_HIT && mips_cm_present())
+		return false;
+
+	/*
+	 * Hardware doesn't globalize the required cache ops, so SMP calls may
+	 * be needed, but only if there are foreign CPUs (non-siblings with
+	 * separate caches).
+	 */
+	/* cpu_foreign_map[] undeclared when !CONFIG_SMP */
+#ifdef CONFIG_SMP
+	return !cpumask_empty(&cpu_foreign_map[0]);
+#else
+	return false;
+#endif
+}
+
+/*
+ * Special Variant of smp_call_function for use by cache functions:
+ *
+ *  o No return value
+ *  o collapses to normal function call on UP kernels
+ *  o collapses to normal function call on systems with a single shared
+ *    primary cache.
+ *  o doesn't disable interrupts on the local CPU
+ */
+static inline void r4k_on_each_cpu(unsigned int type,
+				   void (*func)(void *info), void *info)
+{
+	preempt_disable();
+	if (r4k_op_needs_ipi(type))
+		smp_call_function_many(&cpu_foreign_map[smp_processor_id()],
+				       func, info, 1);
+	func(info);
+	preempt_enable();
+}
+
+/*
+ * Must die.
+ */
+static unsigned long icache_size __read_mostly;
+static unsigned long dcache_size __read_mostly;
+static unsigned long vcache_size __read_mostly;
+static unsigned long scache_size __read_mostly;
+
+/*
+ * Dummy cache handling routines for machines without boardcaches
+ */
+static void cache_noop(void) {}
+
+static struct bcache_ops no_sc_ops = {
+	.bc_enable = (void *)cache_noop,
+	.bc_disable = (void *)cache_noop,
+	.bc_wback_inv = (void *)cache_noop,
+	.bc_inv = (void *)cache_noop
+};
+
+struct bcache_ops *bcops = &no_sc_ops;
+
+#define cpu_is_r4600_v1_x()	((read_c0_prid() & 0xfffffff0) == 0x00002010)
+#define cpu_is_r4600_v2_x()	((read_c0_prid() & 0xfffffff0) == 0x00002020)
+
+#define R4600_HIT_CACHEOP_WAR_IMPL					\
+do {									\
+	if (IS_ENABLED(CONFIG_WAR_R4600_V2_HIT_CACHEOP) &&		\
+	    cpu_is_r4600_v2_x())					\
+		*(volatile unsigned long *)CKSEG1;			\
+	if (IS_ENABLED(CONFIG_WAR_R4600_V1_HIT_CACHEOP))					\
+		__asm__ __volatile__("nop;nop;nop;nop");		\
+} while (0)
+
+static void (*r4k_blast_dcache_page)(unsigned long addr);
+
+static inline void r4k_blast_dcache_page_dc32(unsigned long addr)
+{
+	R4600_HIT_CACHEOP_WAR_IMPL;
+	blast_dcache32_page(addr);
+}
+
+static inline void r4k_blast_dcache_page_dc64(unsigned long addr)
+{
+	blast_dcache64_page(addr);
+}
+
+static inline void r4k_blast_dcache_page_dc128(unsigned long addr)
+{
+	blast_dcache128_page(addr);
+}
+
+static void r4k_blast_dcache_page_setup(void)
+{
+	unsigned long  dc_lsize = cpu_dcache_line_size();
+
+	switch (dc_lsize) {
+	case 0:
+		r4k_blast_dcache_page = (void *)cache_noop;
+		break;
+	case 16:
+		r4k_blast_dcache_page = blast_dcache16_page;
+		break;
+	case 32:
+		r4k_blast_dcache_page = r4k_blast_dcache_page_dc32;
+		break;
+	case 64:
+		r4k_blast_dcache_page = r4k_blast_dcache_page_dc64;
+		break;
+	case 128:
+		r4k_blast_dcache_page = r4k_blast_dcache_page_dc128;
+		break;
+	default:
+		break;
+	}
+}
+
+#ifndef CONFIG_EVA
+#define r4k_blast_dcache_user_page  r4k_blast_dcache_page
+#else
+
+static void (*r4k_blast_dcache_user_page)(unsigned long addr);
+
+static void r4k_blast_dcache_user_page_setup(void)
+{
+	unsigned long  dc_lsize = cpu_dcache_line_size();
+
+	if (dc_lsize == 0)
+		r4k_blast_dcache_user_page = (void *)cache_noop;
+	else if (dc_lsize == 16)
+		r4k_blast_dcache_user_page = blast_dcache16_user_page;
+	else if (dc_lsize == 32)
+		r4k_blast_dcache_user_page = blast_dcache32_user_page;
+	else if (dc_lsize == 64)
+		r4k_blast_dcache_user_page = blast_dcache64_user_page;
+}
+
+#endif
+
+static void (* r4k_blast_dcache_page_indexed)(unsigned long addr);
+
+static void r4k_blast_dcache_page_indexed_setup(void)
+{
+	unsigned long dc_lsize = cpu_dcache_line_size();
+
+	if (dc_lsize == 0)
+		r4k_blast_dcache_page_indexed = (void *)cache_noop;
+	else if (dc_lsize == 16)
+		r4k_blast_dcache_page_indexed = blast_dcache16_page_indexed;
+	else if (dc_lsize == 32)
+		r4k_blast_dcache_page_indexed = blast_dcache32_page_indexed;
+	else if (dc_lsize == 64)
+		r4k_blast_dcache_page_indexed = blast_dcache64_page_indexed;
+	else if (dc_lsize == 128)
+		r4k_blast_dcache_page_indexed = blast_dcache128_page_indexed;
+}
+
+void (* r4k_blast_dcache)(void);
+EXPORT_SYMBOL(r4k_blast_dcache);
+
+static void r4k_blast_dcache_setup(void)
+{
+	unsigned long dc_lsize = cpu_dcache_line_size();
+
+	if (dc_lsize == 0)
+		r4k_blast_dcache = (void *)cache_noop;
+	else if (dc_lsize == 16)
+		r4k_blast_dcache = blast_dcache16;
+	else if (dc_lsize == 32)
+		r4k_blast_dcache = blast_dcache32;
+	else if (dc_lsize == 64)
+		r4k_blast_dcache = blast_dcache64;
+	else if (dc_lsize == 128)
+		r4k_blast_dcache = blast_dcache128;
+}
+
+/* force code alignment (used for CONFIG_WAR_TX49XX_ICACHE_INDEX_INV) */
+#define JUMP_TO_ALIGN(order) \
+	__asm__ __volatile__( \
+		"b\t1f\n\t" \
+		".align\t" #order "\n\t" \
+		"1:\n\t" \
+		)
+#define CACHE32_UNROLL32_ALIGN	JUMP_TO_ALIGN(10) /* 32 * 32 = 1024 */
+#define CACHE32_UNROLL32_ALIGN2 JUMP_TO_ALIGN(11)
+
+static inline void blast_r4600_v1_icache32(void)
+{
+	unsigned long flags;
+
+	local_irq_save(flags);
+	blast_icache32();
+	local_irq_restore(flags);
+}
+
+static inline void tx49_blast_icache32(void)
+{
+	unsigned long start = INDEX_BASE;
+	unsigned long end = start + current_cpu_data.icache.waysize;
+	unsigned long ws_inc = 1UL << current_cpu_data.icache.waybit;
+	unsigned long ws_end = current_cpu_data.icache.ways <<
+			       current_cpu_data.icache.waybit;
+	unsigned long ws, addr;
+
+	CACHE32_UNROLL32_ALIGN2;
+	/* I'm in even chunk.  blast odd chunks */
+	for (ws = 0; ws < ws_end; ws += ws_inc)
+		for (addr = start + 0x400; addr < end; addr += 0x400 * 2)
+			cache_unroll(32, kernel_cache, Index_Invalidate_I,
+				     addr | ws, 32);
+	CACHE32_UNROLL32_ALIGN;
+	/* I'm in odd chunk.  blast even chunks */
+	for (ws = 0; ws < ws_end; ws += ws_inc)
+		for (addr = start; addr < end; addr += 0x400 * 2)
+			cache_unroll(32, kernel_cache, Index_Invalidate_I,
+				     addr | ws, 32);
+}
+
+static inline void blast_icache32_r4600_v1_page_indexed(unsigned long page)
+{
+	unsigned long flags;
+
+	local_irq_save(flags);
+	blast_icache32_page_indexed(page);
+	local_irq_restore(flags);
+}
+
+static inline void tx49_blast_icache32_page_indexed(unsigned long page)
+{
+	unsigned long indexmask = current_cpu_data.icache.waysize - 1;
+	unsigned long start = INDEX_BASE + (page & indexmask);
+	unsigned long end = start + PAGE_SIZE;
+	unsigned long ws_inc = 1UL << current_cpu_data.icache.waybit;
+	unsigned long ws_end = current_cpu_data.icache.ways <<
+			       current_cpu_data.icache.waybit;
+	unsigned long ws, addr;
+
+	CACHE32_UNROLL32_ALIGN2;
+	/* I'm in even chunk.  blast odd chunks */
+	for (ws = 0; ws < ws_end; ws += ws_inc)
+		for (addr = start + 0x400; addr < end; addr += 0x400 * 2)
+			cache_unroll(32, kernel_cache, Index_Invalidate_I,
+				     addr | ws, 32);
+	CACHE32_UNROLL32_ALIGN;
+	/* I'm in odd chunk.  blast even chunks */
+	for (ws = 0; ws < ws_end; ws += ws_inc)
+		for (addr = start; addr < end; addr += 0x400 * 2)
+			cache_unroll(32, kernel_cache, Index_Invalidate_I,
+				     addr | ws, 32);
+}
+
+static void (* r4k_blast_icache_page)(unsigned long addr);
+
+static void r4k_blast_icache_page_setup(void)
+{
+	unsigned long ic_lsize = cpu_icache_line_size();
+
+	if (ic_lsize == 0)
+		r4k_blast_icache_page = (void *)cache_noop;
+	else if (ic_lsize == 16)
+		r4k_blast_icache_page = blast_icache16_page;
+	else if (ic_lsize == 32 && current_cpu_type() == CPU_LOONGSON2EF)
+		r4k_blast_icache_page = loongson2_blast_icache32_page;
+	else if (ic_lsize == 32)
+		r4k_blast_icache_page = blast_icache32_page;
+	else if (ic_lsize == 64)
+		r4k_blast_icache_page = blast_icache64_page;
+	else if (ic_lsize == 128)
+		r4k_blast_icache_page = blast_icache128_page;
+}
+
+#ifndef CONFIG_EVA
+#define r4k_blast_icache_user_page  r4k_blast_icache_page
+#else
+
+static void (*r4k_blast_icache_user_page)(unsigned long addr);
+
+static void r4k_blast_icache_user_page_setup(void)
+{
+	unsigned long ic_lsize = cpu_icache_line_size();
+
+	if (ic_lsize == 0)
+		r4k_blast_icache_user_page = (void *)cache_noop;
+	else if (ic_lsize == 16)
+		r4k_blast_icache_user_page = blast_icache16_user_page;
+	else if (ic_lsize == 32)
+		r4k_blast_icache_user_page = blast_icache32_user_page;
+	else if (ic_lsize == 64)
+		r4k_blast_icache_user_page = blast_icache64_user_page;
+}
+
+#endif
+
+static void (* r4k_blast_icache_page_indexed)(unsigned long addr);
+
+static void r4k_blast_icache_page_indexed_setup(void)
+{
+	unsigned long ic_lsize = cpu_icache_line_size();
+
+	if (ic_lsize == 0)
+		r4k_blast_icache_page_indexed = (void *)cache_noop;
+	else if (ic_lsize == 16)
+		r4k_blast_icache_page_indexed = blast_icache16_page_indexed;
+	else if (ic_lsize == 32) {
+		if (IS_ENABLED(CONFIG_WAR_R4600_V1_INDEX_ICACHEOP) &&
+		    cpu_is_r4600_v1_x())
+			r4k_blast_icache_page_indexed =
+				blast_icache32_r4600_v1_page_indexed;
+		else if (IS_ENABLED(CONFIG_WAR_TX49XX_ICACHE_INDEX_INV))
+			r4k_blast_icache_page_indexed =
+				tx49_blast_icache32_page_indexed;
+		else if (current_cpu_type() == CPU_LOONGSON2EF)
+			r4k_blast_icache_page_indexed =
+				loongson2_blast_icache32_page_indexed;
+		else
+			r4k_blast_icache_page_indexed =
+				blast_icache32_page_indexed;
+	} else if (ic_lsize == 64)
+		r4k_blast_icache_page_indexed = blast_icache64_page_indexed;
+}
+
+void (* r4k_blast_icache)(void);
+EXPORT_SYMBOL(r4k_blast_icache);
+
+static void r4k_blast_icache_setup(void)
+{
+	unsigned long ic_lsize = cpu_icache_line_size();
+
+	if (ic_lsize == 0)
+		r4k_blast_icache = (void *)cache_noop;
+	else if (ic_lsize == 16)
+		r4k_blast_icache = blast_icache16;
+	else if (ic_lsize == 32) {
+		if (IS_ENABLED(CONFIG_WAR_R4600_V1_INDEX_ICACHEOP) &&
+		    cpu_is_r4600_v1_x())
+			r4k_blast_icache = blast_r4600_v1_icache32;
+		else if (IS_ENABLED(CONFIG_WAR_TX49XX_ICACHE_INDEX_INV))
+			r4k_blast_icache = tx49_blast_icache32;
+		else if (current_cpu_type() == CPU_LOONGSON2EF)
+			r4k_blast_icache = loongson2_blast_icache32;
+		else
+			r4k_blast_icache = blast_icache32;
+	} else if (ic_lsize == 64)
+		r4k_blast_icache = blast_icache64;
+	else if (ic_lsize == 128)
+		r4k_blast_icache = blast_icache128;
+}
+
+static void (* r4k_blast_scache_page)(unsigned long addr);
+
+static void r4k_blast_scache_page_setup(void)
+{
+	unsigned long sc_lsize = cpu_scache_line_size();
+
+	if (scache_size == 0)
+		r4k_blast_scache_page = (void *)cache_noop;
+	else if (sc_lsize == 16)
+		r4k_blast_scache_page = blast_scache16_page;
+	else if (sc_lsize == 32)
+		r4k_blast_scache_page = blast_scache32_page;
+	else if (sc_lsize == 64)
+		r4k_blast_scache_page = blast_scache64_page;
+	else if (sc_lsize == 128)
+		r4k_blast_scache_page = blast_scache128_page;
+}
+
+static void (* r4k_blast_scache_page_indexed)(unsigned long addr);
+
+static void r4k_blast_scache_page_indexed_setup(void)
+{
+	unsigned long sc_lsize = cpu_scache_line_size();
+
+	if (scache_size == 0)
+		r4k_blast_scache_page_indexed = (void *)cache_noop;
+	else if (sc_lsize == 16)
+		r4k_blast_scache_page_indexed = blast_scache16_page_indexed;
+	else if (sc_lsize == 32)
+		r4k_blast_scache_page_indexed = blast_scache32_page_indexed;
+	else if (sc_lsize == 64)
+		r4k_blast_scache_page_indexed = blast_scache64_page_indexed;
+	else if (sc_lsize == 128)
+		r4k_blast_scache_page_indexed = blast_scache128_page_indexed;
+}
+
+static void (* r4k_blast_scache)(void);
+
+static void r4k_blast_scache_setup(void)
+{
+	unsigned long sc_lsize = cpu_scache_line_size();
+
+	if (scache_size == 0)
+		r4k_blast_scache = (void *)cache_noop;
+	else if (sc_lsize == 16)
+		r4k_blast_scache = blast_scache16;
+	else if (sc_lsize == 32)
+		r4k_blast_scache = blast_scache32;
+	else if (sc_lsize == 64)
+		r4k_blast_scache = blast_scache64;
+	else if (sc_lsize == 128)
+		r4k_blast_scache = blast_scache128;
+}
+
+static void (*r4k_blast_scache_node)(long node);
+
+static void r4k_blast_scache_node_setup(void)
+{
+	unsigned long sc_lsize = cpu_scache_line_size();
+
+	if (current_cpu_type() != CPU_LOONGSON64)
+		r4k_blast_scache_node = (void *)cache_noop;
+	else if (sc_lsize == 16)
+		r4k_blast_scache_node = blast_scache16_node;
+	else if (sc_lsize == 32)
+		r4k_blast_scache_node = blast_scache32_node;
+	else if (sc_lsize == 64)
+		r4k_blast_scache_node = blast_scache64_node;
+	else if (sc_lsize == 128)
+		r4k_blast_scache_node = blast_scache128_node;
+}
+
+static inline void local_r4k___flush_cache_all(void * args)
+{
+	switch (current_cpu_type()) {
+	case CPU_LOONGSON2EF:
+	case CPU_R4000SC:
+	case CPU_R4000MC:
+	case CPU_R4400SC:
+	case CPU_R4400MC:
+	case CPU_R10000:
+	case CPU_R12000:
+	case CPU_R14000:
+	case CPU_R16000:
+		/*
+		 * These caches are inclusive caches, that is, if something
+		 * is not cached in the S-cache, we know it also won't be
+		 * in one of the primary caches.
+		 */
+		r4k_blast_scache();
+		break;
+
+	case CPU_LOONGSON64:
+		/* Use get_ebase_cpunum() for both NUMA=y/n */
+		r4k_blast_scache_node(get_ebase_cpunum() >> 2);
+		break;
+
+	case CPU_BMIPS5000:
+		r4k_blast_scache();
+		__sync();
+		break;
+
+	default:
+		r4k_blast_dcache();
+		r4k_blast_icache();
+		break;
+	}
+}
+
+static void r4k___flush_cache_all(void)
+{
+	r4k_on_each_cpu(R4K_INDEX, local_r4k___flush_cache_all, NULL);
+}
+
+/**
+ * has_valid_asid() - Determine if an mm already has an ASID.
+ * @mm:		Memory map.
+ * @type:	R4K_HIT or R4K_INDEX, type of cache op.
+ *
+ * Determines whether @mm already has an ASID on any of the CPUs which cache ops
+ * of type @type within an r4k_on_each_cpu() call will affect. If
+ * r4k_on_each_cpu() does an SMP call to a single VPE in each core, then the
+ * scope of the operation is confined to sibling CPUs, otherwise all online CPUs
+ * will need to be checked.
+ *
+ * Must be called in non-preemptive context.
+ *
+ * Returns:	1 if the CPUs affected by @type cache ops have an ASID for @mm.
+ *		0 otherwise.
+ */
+static inline int has_valid_asid(const struct mm_struct *mm, unsigned int type)
+{
+	unsigned int i;
+	const cpumask_t *mask = cpu_present_mask;
+
+	if (cpu_has_mmid)
+		return cpu_context(0, mm) != 0;
+
+	/* cpu_sibling_map[] undeclared when !CONFIG_SMP */
+#ifdef CONFIG_SMP
+	/*
+	 * If r4k_on_each_cpu does SMP calls, it does them to a single VPE in
+	 * each foreign core, so we only need to worry about siblings.
+	 * Otherwise we need to worry about all present CPUs.
+	 */
+	if (r4k_op_needs_ipi(type))
+		mask = &cpu_sibling_map[smp_processor_id()];
+#endif
+	for_each_cpu(i, mask)
+		if (cpu_context(i, mm))
+			return 1;
+	return 0;
+}
+
+static void r4k__flush_cache_vmap(void)
+{
+	r4k_blast_dcache();
+}
+
+static void r4k__flush_cache_vunmap(void)
+{
+	r4k_blast_dcache();
+}
+
+/*
+ * Note: flush_tlb_range() assumes flush_cache_range() sufficiently flushes
+ * whole caches when vma is executable.
+ */
+static inline void local_r4k_flush_cache_range(void * args)
+{
+	struct vm_area_struct *vma = args;
+	int exec = vma->vm_flags & VM_EXEC;
+
+	if (!has_valid_asid(vma->vm_mm, R4K_INDEX))
+		return;
+
+	/*
+	 * If dcache can alias, we must blast it since mapping is changing.
+	 * If executable, we must ensure any dirty lines are written back far
+	 * enough to be visible to icache.
+	 */
+	if (cpu_has_dc_aliases || (exec && !cpu_has_ic_fills_f_dc))
+		r4k_blast_dcache();
+	/* If executable, blast stale lines from icache */
+	if (exec)
+		r4k_blast_icache();
+}
+
+static void r4k_flush_cache_range(struct vm_area_struct *vma,
+	unsigned long start, unsigned long end)
+{
+	int exec = vma->vm_flags & VM_EXEC;
+
+	if (cpu_has_dc_aliases || exec)
+		r4k_on_each_cpu(R4K_INDEX, local_r4k_flush_cache_range, vma);
+}
+
+static inline void local_r4k_flush_cache_mm(void * args)
+{
+	struct mm_struct *mm = args;
+
+	if (!has_valid_asid(mm, R4K_INDEX))
+		return;
+
+	/*
+	 * Kludge alert.  For obscure reasons R4000SC and R4400SC go nuts if we
+	 * only flush the primary caches but R1x000 behave sane ...
+	 * R4000SC and R4400SC indexed S-cache ops also invalidate primary
+	 * caches, so we can bail out early.
+	 */
+	if (current_cpu_type() == CPU_R4000SC ||
+	    current_cpu_type() == CPU_R4000MC ||
+	    current_cpu_type() == CPU_R4400SC ||
+	    current_cpu_type() == CPU_R4400MC) {
+		r4k_blast_scache();
+		return;
+	}
+
+	r4k_blast_dcache();
+}
+
+static void r4k_flush_cache_mm(struct mm_struct *mm)
+{
+	if (!cpu_has_dc_aliases)
+		return;
+
+	r4k_on_each_cpu(R4K_INDEX, local_r4k_flush_cache_mm, mm);
+}
+
+struct flush_cache_page_args {
+	struct vm_area_struct *vma;
+	unsigned long addr;
+	unsigned long pfn;
+};
+
+static inline void local_r4k_flush_cache_page(void *args)
+{
+	struct flush_cache_page_args *fcp_args = args;
+	struct vm_area_struct *vma = fcp_args->vma;
+	unsigned long addr = fcp_args->addr;
+	struct page *page = pfn_to_page(fcp_args->pfn);
+	int exec = vma->vm_flags & VM_EXEC;
+	struct mm_struct *mm = vma->vm_mm;
+	int map_coherent = 0;
+	pmd_t *pmdp;
+	pte_t *ptep;
+	void *vaddr;
+
+	/*
+	 * If owns no valid ASID yet, cannot possibly have gotten
+	 * this page into the cache.
+	 */
+	if (!has_valid_asid(mm, R4K_HIT))
+		return;
+
+	addr &= PAGE_MASK;
+	pmdp = pmd_off(mm, addr);
+	ptep = pte_offset_kernel(pmdp, addr);
+
+	/*
+	 * If the page isn't marked valid, the page cannot possibly be
+	 * in the cache.
+	 */
+	if (!(pte_present(*ptep)))
+		return;
+
+	if ((mm == current->active_mm) && (pte_val(*ptep) & _PAGE_VALID))
+		vaddr = NULL;
+	else {
+		/*
+		 * Use kmap_coherent or kmap_atomic to do flushes for
+		 * another ASID than the current one.
+		 */
+		map_coherent = (cpu_has_dc_aliases &&
+				page_mapcount(page) &&
+				!Page_dcache_dirty(page));
+		if (map_coherent)
+			vaddr = kmap_coherent(page, addr);
+		else
+			vaddr = kmap_atomic(page);
+		addr = (unsigned long)vaddr;
+	}
+
+	if (cpu_has_dc_aliases || (exec && !cpu_has_ic_fills_f_dc)) {
+		vaddr ? r4k_blast_dcache_page(addr) :
+			r4k_blast_dcache_user_page(addr);
+		if (exec && !cpu_icache_snoops_remote_store)
+			r4k_blast_scache_page(addr);
+	}
+	if (exec) {
+		if (vaddr && cpu_has_vtag_icache && mm == current->active_mm) {
+			drop_mmu_context(mm);
+		} else
+			vaddr ? r4k_blast_icache_page(addr) :
+				r4k_blast_icache_user_page(addr);
+	}
+
+	if (vaddr) {
+		if (map_coherent)
+			kunmap_coherent();
+		else
+			kunmap_atomic(vaddr);
+	}
+}
+
+static void r4k_flush_cache_page(struct vm_area_struct *vma,
+	unsigned long addr, unsigned long pfn)
+{
+	struct flush_cache_page_args args;
+
+	args.vma = vma;
+	args.addr = addr;
+	args.pfn = pfn;
+
+	r4k_on_each_cpu(R4K_HIT, local_r4k_flush_cache_page, &args);
+}
+
+static inline void local_r4k_flush_data_cache_page(void * addr)
+{
+	r4k_blast_dcache_page((unsigned long) addr);
+}
+
+static void r4k_flush_data_cache_page(unsigned long addr)
+{
+	if (in_atomic())
+		local_r4k_flush_data_cache_page((void *)addr);
+	else
+		r4k_on_each_cpu(R4K_HIT, local_r4k_flush_data_cache_page,
+				(void *) addr);
+}
+
+struct flush_icache_range_args {
+	unsigned long start;
+	unsigned long end;
+	unsigned int type;
+	bool user;
+};
+
+static inline void __local_r4k_flush_icache_range(unsigned long start,
+						  unsigned long end,
+						  unsigned int type,
+						  bool user)
+{
+	if (!cpu_has_ic_fills_f_dc) {
+		if (type == R4K_INDEX ||
+		    (type & R4K_INDEX && end - start >= dcache_size)) {
+			r4k_blast_dcache();
+		} else {
+			R4600_HIT_CACHEOP_WAR_IMPL;
+			if (user)
+				protected_blast_dcache_range(start, end);
+			else
+				blast_dcache_range(start, end);
+		}
+	}
+
+	if (type == R4K_INDEX ||
+	    (type & R4K_INDEX && end - start > icache_size))
+		r4k_blast_icache();
+	else {
+		switch (boot_cpu_type()) {
+		case CPU_LOONGSON2EF:
+			protected_loongson2_blast_icache_range(start, end);
+			break;
+
+		default:
+			if (user)
+				protected_blast_icache_range(start, end);
+			else
+				blast_icache_range(start, end);
+			break;
+		}
+	}
+}
+
+static inline void local_r4k_flush_icache_range(unsigned long start,
+						unsigned long end)
+{
+	__local_r4k_flush_icache_range(start, end, R4K_HIT | R4K_INDEX, false);
+}
+
+static inline void local_r4k_flush_icache_user_range(unsigned long start,
+						     unsigned long end)
+{
+	__local_r4k_flush_icache_range(start, end, R4K_HIT | R4K_INDEX, true);
+}
+
+static inline void local_r4k_flush_icache_range_ipi(void *args)
+{
+	struct flush_icache_range_args *fir_args = args;
+	unsigned long start = fir_args->start;
+	unsigned long end = fir_args->end;
+	unsigned int type = fir_args->type;
+	bool user = fir_args->user;
+
+	__local_r4k_flush_icache_range(start, end, type, user);
+}
+
+static void __r4k_flush_icache_range(unsigned long start, unsigned long end,
+				     bool user)
+{
+	struct flush_icache_range_args args;
+	unsigned long size, cache_size;
+
+	args.start = start;
+	args.end = end;
+	args.type = R4K_HIT | R4K_INDEX;
+	args.user = user;
+
+	/*
+	 * Indexed cache ops require an SMP call.
+	 * Consider if that can or should be avoided.
+	 */
+	preempt_disable();
+	if (r4k_op_needs_ipi(R4K_INDEX) && !r4k_op_needs_ipi(R4K_HIT)) {
+		/*
+		 * If address-based cache ops don't require an SMP call, then
+		 * use them exclusively for small flushes.
+		 */
+		size = end - start;
+		cache_size = icache_size;
+		if (!cpu_has_ic_fills_f_dc) {
+			size *= 2;
+			cache_size += dcache_size;
+		}
+		if (size <= cache_size)
+			args.type &= ~R4K_INDEX;
+	}
+	r4k_on_each_cpu(args.type, local_r4k_flush_icache_range_ipi, &args);
+	preempt_enable();
+	instruction_hazard();
+}
+
+static void r4k_flush_icache_range(unsigned long start, unsigned long end)
+{
+	return __r4k_flush_icache_range(start, end, false);
+}
+
+static void r4k_flush_icache_user_range(unsigned long start, unsigned long end)
+{
+	return __r4k_flush_icache_range(start, end, true);
+}
+
+#ifdef CONFIG_DMA_NONCOHERENT
+
+static void r4k_dma_cache_wback_inv(unsigned long addr, unsigned long size)
+{
+	/* Catch bad driver code */
+	if (WARN_ON(size == 0))
+		return;
+
+	preempt_disable();
+	if (cpu_has_inclusive_pcaches) {
+		if (size >= scache_size) {
+			if (current_cpu_type() != CPU_LOONGSON64)
+				r4k_blast_scache();
+			else
+				r4k_blast_scache_node(pa_to_nid(addr));
+		} else {
+			blast_scache_range(addr, addr + size);
+		}
+		preempt_enable();
+		__sync();
+		return;
+	}
+
+	/*
+	 * Either no secondary cache or the available caches don't have the
+	 * subset property so we have to flush the primary caches
+	 * explicitly.
+	 * If we would need IPI to perform an INDEX-type operation, then
+	 * we have to use the HIT-type alternative as IPI cannot be used
+	 * here due to interrupts possibly being disabled.
+	 */
+	if (!r4k_op_needs_ipi(R4K_INDEX) && size >= dcache_size) {
+		r4k_blast_dcache();
+	} else {
+		R4600_HIT_CACHEOP_WAR_IMPL;
+		blast_dcache_range(addr, addr + size);
+	}
+	preempt_enable();
+
+	bc_wback_inv(addr, size);
+	__sync();
+}
+
+static void prefetch_cache_inv(unsigned long addr, unsigned long size)
+{
+	unsigned int linesz = cpu_scache_line_size();
+	unsigned long addr0 = addr, addr1;
+
+	addr0 &= ~(linesz - 1);
+	addr1 = (addr0 + size - 1) & ~(linesz - 1);
+
+	protected_writeback_scache_line(addr0);
+	if (likely(addr1 != addr0))
+		protected_writeback_scache_line(addr1);
+	else
+		return;
+
+	addr0 += linesz;
+	if (likely(addr1 != addr0))
+		protected_writeback_scache_line(addr0);
+	else
+		return;
+
+	addr1 -= linesz;
+	if (likely(addr1 > addr0))
+		protected_writeback_scache_line(addr0);
+}
+
+static void r4k_dma_cache_inv(unsigned long addr, unsigned long size)
+{
+	/* Catch bad driver code */
+	if (WARN_ON(size == 0))
+		return;
+
+	preempt_disable();
+
+	if (current_cpu_type() == CPU_BMIPS5000)
+		prefetch_cache_inv(addr, size);
+
+	if (cpu_has_inclusive_pcaches) {
+		if (size >= scache_size) {
+			if (current_cpu_type() != CPU_LOONGSON64)
+				r4k_blast_scache();
+			else
+				r4k_blast_scache_node(pa_to_nid(addr));
+		} else {
+			/*
+			 * There is no clearly documented alignment requirement
+			 * for the cache instruction on MIPS processors and
+			 * some processors, among them the RM5200 and RM7000
+			 * QED processors will throw an address error for cache
+			 * hit ops with insufficient alignment.	 Solved by
+			 * aligning the address to cache line size.
+			 */
+			blast_inv_scache_range(addr, addr + size);
+		}
+		preempt_enable();
+		__sync();
+		return;
+	}
+
+	if (!r4k_op_needs_ipi(R4K_INDEX) && size >= dcache_size) {
+		r4k_blast_dcache();
+	} else {
+		R4600_HIT_CACHEOP_WAR_IMPL;
+		blast_inv_dcache_range(addr, addr + size);
+	}
+	preempt_enable();
+
+	bc_inv(addr, size);
+	__sync();
+}
+#endif /* CONFIG_DMA_NONCOHERENT */
+
+static void r4k_flush_icache_all(void)
+{
+	if (cpu_has_vtag_icache)
+		r4k_blast_icache();
+}
+
+struct flush_kernel_vmap_range_args {
+	unsigned long	vaddr;
+	int		size;
+};
+
+static inline void local_r4k_flush_kernel_vmap_range_index(void *args)
+{
+	/*
+	 * Aliases only affect the primary caches so don't bother with
+	 * S-caches or T-caches.
+	 */
+	r4k_blast_dcache();
+}
+
+static inline void local_r4k_flush_kernel_vmap_range(void *args)
+{
+	struct flush_kernel_vmap_range_args *vmra = args;
+	unsigned long vaddr = vmra->vaddr;
+	int size = vmra->size;
+
+	/*
+	 * Aliases only affect the primary caches so don't bother with
+	 * S-caches or T-caches.
+	 */
+	R4600_HIT_CACHEOP_WAR_IMPL;
+	blast_dcache_range(vaddr, vaddr + size);
+}
+
+static void r4k_flush_kernel_vmap_range(unsigned long vaddr, int size)
+{
+	struct flush_kernel_vmap_range_args args;
+
+	args.vaddr = (unsigned long) vaddr;
+	args.size = size;
+
+	if (size >= dcache_size)
+		r4k_on_each_cpu(R4K_INDEX,
+				local_r4k_flush_kernel_vmap_range_index, NULL);
+	else
+		r4k_on_each_cpu(R4K_HIT, local_r4k_flush_kernel_vmap_range,
+				&args);
+}
+
+static inline void rm7k_erratum31(void)
+{
+	const unsigned long ic_lsize = 32;
+	unsigned long addr;
+
+	/* RM7000 erratum #31. The icache is screwed at startup. */
+	write_c0_taglo(0);
+	write_c0_taghi(0);
+
+	for (addr = INDEX_BASE; addr <= INDEX_BASE + 4096; addr += ic_lsize) {
+		__asm__ __volatile__ (
+			".set push\n\t"
+			".set noreorder\n\t"
+			".set mips3\n\t"
+			"cache\t%1, 0(%0)\n\t"
+			"cache\t%1, 0x1000(%0)\n\t"
+			"cache\t%1, 0x2000(%0)\n\t"
+			"cache\t%1, 0x3000(%0)\n\t"
+			"cache\t%2, 0(%0)\n\t"
+			"cache\t%2, 0x1000(%0)\n\t"
+			"cache\t%2, 0x2000(%0)\n\t"
+			"cache\t%2, 0x3000(%0)\n\t"
+			"cache\t%1, 0(%0)\n\t"
+			"cache\t%1, 0x1000(%0)\n\t"
+			"cache\t%1, 0x2000(%0)\n\t"
+			"cache\t%1, 0x3000(%0)\n\t"
+			".set pop\n"
+			:
+			: "r" (addr), "i" (Index_Store_Tag_I), "i" (Fill_I));
+	}
+}
+
+static inline int alias_74k_erratum(struct cpuinfo_mips *c)
+{
+	unsigned int imp = c->processor_id & PRID_IMP_MASK;
+	unsigned int rev = c->processor_id & PRID_REV_MASK;
+	int present = 0;
+
+	/*
+	 * Early versions of the 74K do not update the cache tags on a
+	 * vtag miss/ptag hit which can occur in the case of KSEG0/KUSEG
+	 * aliases.  In this case it is better to treat the cache as always
+	 * having aliases.  Also disable the synonym tag update feature
+	 * where available.  In this case no opportunistic tag update will
+	 * happen where a load causes a virtual address miss but a physical
+	 * address hit during a D-cache look-up.
+	 */
+	switch (imp) {
+	case PRID_IMP_74K:
+		if (rev <= PRID_REV_ENCODE_332(2, 4, 0))
+			present = 1;
+		if (rev == PRID_REV_ENCODE_332(2, 4, 0))
+			write_c0_config6(read_c0_config6() | MTI_CONF6_SYND);
+		break;
+	case PRID_IMP_1074K:
+		if (rev <= PRID_REV_ENCODE_332(1, 1, 0)) {
+			present = 1;
+			write_c0_config6(read_c0_config6() | MTI_CONF6_SYND);
+		}
+		break;
+	default:
+		BUG();
+	}
+
+	return present;
+}
+
+static void b5k_instruction_hazard(void)
+{
+	__sync();
+	__sync();
+	__asm__ __volatile__(
+	"       nop; nop; nop; nop; nop; nop; nop; nop\n"
+	"       nop; nop; nop; nop; nop; nop; nop; nop\n"
+	"       nop; nop; nop; nop; nop; nop; nop; nop\n"
+	"       nop; nop; nop; nop; nop; nop; nop; nop\n"
+	: : : "memory");
+}
+
+static char *way_string[] = { NULL, "direct mapped", "2-way",
+	"3-way", "4-way", "5-way", "6-way", "7-way", "8-way",
+	"9-way", "10-way", "11-way", "12-way",
+	"13-way", "14-way", "15-way", "16-way",
+};
+
+static void probe_pcache(void)
+{
+	struct cpuinfo_mips *c = &current_cpu_data;
+	unsigned int config = read_c0_config();
+	unsigned int prid = read_c0_prid();
+	int has_74k_erratum = 0;
+	unsigned long config1;
+	unsigned int lsize;
+
+	switch (current_cpu_type()) {
+	case CPU_R4600:			/* QED style two way caches? */
+	case CPU_R4700:
+	case CPU_R5000:
+	case CPU_NEVADA:
+		icache_size = 1 << (12 + ((config & CONF_IC) >> 9));
+		c->icache.linesz = 16 << ((config & CONF_IB) >> 5);
+		c->icache.ways = 2;
+		c->icache.waybit = __ffs(icache_size/2);
+
+		dcache_size = 1 << (12 + ((config & CONF_DC) >> 6));
+		c->dcache.linesz = 16 << ((config & CONF_DB) >> 4);
+		c->dcache.ways = 2;
+		c->dcache.waybit= __ffs(dcache_size/2);
+
+		c->options |= MIPS_CPU_CACHE_CDEX_P;
+		break;
+
+	case CPU_R5500:
+		icache_size = 1 << (12 + ((config & CONF_IC) >> 9));
+		c->icache.linesz = 16 << ((config & CONF_IB) >> 5);
+		c->icache.ways = 2;
+		c->icache.waybit= 0;
+
+		dcache_size = 1 << (12 + ((config & CONF_DC) >> 6));
+		c->dcache.linesz = 16 << ((config & CONF_DB) >> 4);
+		c->dcache.ways = 2;
+		c->dcache.waybit = 0;
+
+		c->options |= MIPS_CPU_CACHE_CDEX_P | MIPS_CPU_PREFETCH;
+		break;
+
+	case CPU_TX49XX:
+		icache_size = 1 << (12 + ((config & CONF_IC) >> 9));
+		c->icache.linesz = 16 << ((config & CONF_IB) >> 5);
+		c->icache.ways = 4;
+		c->icache.waybit= 0;
+
+		dcache_size = 1 << (12 + ((config & CONF_DC) >> 6));
+		c->dcache.linesz = 16 << ((config & CONF_DB) >> 4);
+		c->dcache.ways = 4;
+		c->dcache.waybit = 0;
+
+		c->options |= MIPS_CPU_CACHE_CDEX_P;
+		c->options |= MIPS_CPU_PREFETCH;
+		break;
+
+	case CPU_R4000PC:
+	case CPU_R4000SC:
+	case CPU_R4000MC:
+	case CPU_R4400PC:
+	case CPU_R4400SC:
+	case CPU_R4400MC:
+	case CPU_R4300:
+		icache_size = 1 << (12 + ((config & CONF_IC) >> 9));
+		c->icache.linesz = 16 << ((config & CONF_IB) >> 5);
+		c->icache.ways = 1;
+		c->icache.waybit = 0;	/* doesn't matter */
+
+		dcache_size = 1 << (12 + ((config & CONF_DC) >> 6));
+		c->dcache.linesz = 16 << ((config & CONF_DB) >> 4);
+		c->dcache.ways = 1;
+		c->dcache.waybit = 0;	/* does not matter */
+
+		c->options |= MIPS_CPU_CACHE_CDEX_P;
+		break;
+
+	case CPU_R10000:
+	case CPU_R12000:
+	case CPU_R14000:
+	case CPU_R16000:
+		icache_size = 1 << (12 + ((config & R10K_CONF_IC) >> 29));
+		c->icache.linesz = 64;
+		c->icache.ways = 2;
+		c->icache.waybit = 0;
+
+		dcache_size = 1 << (12 + ((config & R10K_CONF_DC) >> 26));
+		c->dcache.linesz = 32;
+		c->dcache.ways = 2;
+		c->dcache.waybit = 0;
+
+		c->options |= MIPS_CPU_PREFETCH;
+		break;
+
+	case CPU_RM7000:
+		rm7k_erratum31();
+
+		icache_size = 1 << (12 + ((config & CONF_IC) >> 9));
+		c->icache.linesz = 16 << ((config & CONF_IB) >> 5);
+		c->icache.ways = 4;
+		c->icache.waybit = __ffs(icache_size / c->icache.ways);
+
+		dcache_size = 1 << (12 + ((config & CONF_DC) >> 6));
+		c->dcache.linesz = 16 << ((config & CONF_DB) >> 4);
+		c->dcache.ways = 4;
+		c->dcache.waybit = __ffs(dcache_size / c->dcache.ways);
+
+		c->options |= MIPS_CPU_CACHE_CDEX_P;
+		c->options |= MIPS_CPU_PREFETCH;
+		break;
+
+	case CPU_LOONGSON2EF:
+		icache_size = 1 << (12 + ((config & CONF_IC) >> 9));
+		c->icache.linesz = 16 << ((config & CONF_IB) >> 5);
+		if (prid & 0x3)
+			c->icache.ways = 4;
+		else
+			c->icache.ways = 2;
+		c->icache.waybit = 0;
+
+		dcache_size = 1 << (12 + ((config & CONF_DC) >> 6));
+		c->dcache.linesz = 16 << ((config & CONF_DB) >> 4);
+		if (prid & 0x3)
+			c->dcache.ways = 4;
+		else
+			c->dcache.ways = 2;
+		c->dcache.waybit = 0;
+		break;
+
+	case CPU_LOONGSON64:
+		config1 = read_c0_config1();
+		lsize = (config1 >> 19) & 7;
+		if (lsize)
+			c->icache.linesz = 2 << lsize;
+		else
+			c->icache.linesz = 0;
+		c->icache.sets = 64 << ((config1 >> 22) & 7);
+		c->icache.ways = 1 + ((config1 >> 16) & 7);
+		icache_size = c->icache.sets *
+					  c->icache.ways *
+					  c->icache.linesz;
+		c->icache.waybit = 0;
+
+		lsize = (config1 >> 10) & 7;
+		if (lsize)
+			c->dcache.linesz = 2 << lsize;
+		else
+			c->dcache.linesz = 0;
+		c->dcache.sets = 64 << ((config1 >> 13) & 7);
+		c->dcache.ways = 1 + ((config1 >> 7) & 7);
+		dcache_size = c->dcache.sets *
+					  c->dcache.ways *
+					  c->dcache.linesz;
+		c->dcache.waybit = 0;
+		if ((c->processor_id & (PRID_IMP_MASK | PRID_REV_MASK)) >=
+				(PRID_IMP_LOONGSON_64C | PRID_REV_LOONGSON3A_R2_0) ||
+				(c->processor_id & PRID_IMP_MASK) == PRID_IMP_LOONGSON_64R)
+			c->options |= MIPS_CPU_PREFETCH;
+		break;
+
+	case CPU_CAVIUM_OCTEON3:
+		/* For now lie about the number of ways. */
+		c->icache.linesz = 128;
+		c->icache.sets = 16;
+		c->icache.ways = 8;
+		c->icache.flags |= MIPS_CACHE_VTAG;
+		icache_size = c->icache.sets * c->icache.ways * c->icache.linesz;
+
+		c->dcache.linesz = 128;
+		c->dcache.ways = 8;
+		c->dcache.sets = 8;
+		dcache_size = c->dcache.sets * c->dcache.ways * c->dcache.linesz;
+		c->options |= MIPS_CPU_PREFETCH;
+		break;
+
+	default:
+		if (!(config & MIPS_CONF_M))
+			panic("Don't know how to probe P-caches on this cpu.");
+
+		/*
+		 * So we seem to be a MIPS32 or MIPS64 CPU
+		 * So let's probe the I-cache ...
+		 */
+		config1 = read_c0_config1();
+
+		lsize = (config1 >> 19) & 7;
+
+		/* IL == 7 is reserved */
+		if (lsize == 7)
+			panic("Invalid icache line size");
+
+		c->icache.linesz = lsize ? 2 << lsize : 0;
+
+		c->icache.sets = 32 << (((config1 >> 22) + 1) & 7);
+		c->icache.ways = 1 + ((config1 >> 16) & 7);
+
+		icache_size = c->icache.sets *
+			      c->icache.ways *
+			      c->icache.linesz;
+		c->icache.waybit = __ffs(icache_size/c->icache.ways);
+
+		if (config & MIPS_CONF_VI)
+			c->icache.flags |= MIPS_CACHE_VTAG;
+
+		/*
+		 * Now probe the MIPS32 / MIPS64 data cache.
+		 */
+		c->dcache.flags = 0;
+
+		lsize = (config1 >> 10) & 7;
+
+		/* DL == 7 is reserved */
+		if (lsize == 7)
+			panic("Invalid dcache line size");
+
+		c->dcache.linesz = lsize ? 2 << lsize : 0;
+
+		c->dcache.sets = 32 << (((config1 >> 13) + 1) & 7);
+		c->dcache.ways = 1 + ((config1 >> 7) & 7);
+
+		dcache_size = c->dcache.sets *
+			      c->dcache.ways *
+			      c->dcache.linesz;
+		c->dcache.waybit = __ffs(dcache_size/c->dcache.ways);
+
+		c->options |= MIPS_CPU_PREFETCH;
+		break;
+	}
+
+	/*
+	 * Processor configuration sanity check for the R4000SC erratum
+	 * #5.	With page sizes larger than 32kB there is no possibility
+	 * to get a VCE exception anymore so we don't care about this
+	 * misconfiguration.  The case is rather theoretical anyway;
+	 * presumably no vendor is shipping his hardware in the "bad"
+	 * configuration.
+	 */
+	if ((prid & PRID_IMP_MASK) == PRID_IMP_R4000 &&
+	    (prid & PRID_REV_MASK) < PRID_REV_R4400 &&
+	    !(config & CONF_SC) && c->icache.linesz != 16 &&
+	    PAGE_SIZE <= 0x8000)
+		panic("Improper R4000SC processor configuration detected");
+
+	/* compute a couple of other cache variables */
+	c->icache.waysize = icache_size / c->icache.ways;
+	c->dcache.waysize = dcache_size / c->dcache.ways;
+
+	c->icache.sets = c->icache.linesz ?
+		icache_size / (c->icache.linesz * c->icache.ways) : 0;
+	c->dcache.sets = c->dcache.linesz ?
+		dcache_size / (c->dcache.linesz * c->dcache.ways) : 0;
+
+	/*
+	 * R1x000 P-caches are odd in a positive way.  They're 32kB 2-way
+	 * virtually indexed so normally would suffer from aliases.  So
+	 * normally they'd suffer from aliases but magic in the hardware deals
+	 * with that for us so we don't need to take care ourselves.
+	 */
+	switch (current_cpu_type()) {
+	case CPU_20KC:
+	case CPU_25KF:
+	case CPU_I6400:
+	case CPU_I6500:
+	case CPU_SB1:
+	case CPU_SB1A:
+		c->dcache.flags |= MIPS_CACHE_PINDEX;
+		break;
+
+	case CPU_R10000:
+	case CPU_R12000:
+	case CPU_R14000:
+	case CPU_R16000:
+		break;
+
+	case CPU_74K:
+	case CPU_1074K:
+		has_74k_erratum = alias_74k_erratum(c);
+		fallthrough;
+	case CPU_M14KC:
+	case CPU_M14KEC:
+	case CPU_24K:
+	case CPU_34K:
+	case CPU_1004K:
+	case CPU_INTERAPTIV:
+	case CPU_P5600:
+	case CPU_PROAPTIV:
+	case CPU_M5150:
+	case CPU_QEMU_GENERIC:
+	case CPU_P6600:
+	case CPU_M6250:
+		if (!(read_c0_config7() & MIPS_CONF7_IAR) &&
+		    (c->icache.waysize > PAGE_SIZE))
+			c->icache.flags |= MIPS_CACHE_ALIASES;
+		if (!has_74k_erratum && (read_c0_config7() & MIPS_CONF7_AR)) {
+			/*
+			 * Effectively physically indexed dcache,
+			 * thus no virtual aliases.
+			*/
+			c->dcache.flags |= MIPS_CACHE_PINDEX;
+			break;
+		}
+		fallthrough;
+	default:
+		if (has_74k_erratum || c->dcache.waysize > PAGE_SIZE)
+			c->dcache.flags |= MIPS_CACHE_ALIASES;
+	}
+
+	/* Physically indexed caches don't suffer from virtual aliasing */
+	if (c->dcache.flags & MIPS_CACHE_PINDEX)
+		c->dcache.flags &= ~MIPS_CACHE_ALIASES;
+
+	/*
+	 * In systems with CM the icache fills from L2 or closer caches, and
+	 * thus sees remote stores without needing to write them back any
+	 * further than that.
+	 */
+	if (mips_cm_present())
+		c->icache.flags |= MIPS_IC_SNOOPS_REMOTE;
+
+	switch (current_cpu_type()) {
+	case CPU_20KC:
+		/*
+		 * Some older 20Kc chips doesn't have the 'VI' bit in
+		 * the config register.
+		 */
+		c->icache.flags |= MIPS_CACHE_VTAG;
+		break;
+
+	case CPU_ALCHEMY:
+	case CPU_I6400:
+	case CPU_I6500:
+		c->icache.flags |= MIPS_CACHE_IC_F_DC;
+		break;
+
+	case CPU_BMIPS5000:
+		c->icache.flags |= MIPS_CACHE_IC_F_DC;
+		/* Cache aliases are handled in hardware; allow HIGHMEM */
+		c->dcache.flags &= ~MIPS_CACHE_ALIASES;
+		break;
+
+	case CPU_LOONGSON2EF:
+		/*
+		 * LOONGSON2 has 4 way icache, but when using indexed cache op,
+		 * one op will act on all 4 ways
+		 */
+		c->icache.ways = 1;
+	}
+
+	pr_info("Primary instruction cache %ldkB, %s, %s, linesize %d bytes.\n",
+		icache_size >> 10,
+		c->icache.flags & MIPS_CACHE_VTAG ? "VIVT" : "VIPT",
+		way_string[c->icache.ways], c->icache.linesz);
+
+	pr_info("Primary data cache %ldkB, %s, %s, %s, linesize %d bytes\n",
+		dcache_size >> 10, way_string[c->dcache.ways],
+		(c->dcache.flags & MIPS_CACHE_PINDEX) ? "PIPT" : "VIPT",
+		(c->dcache.flags & MIPS_CACHE_ALIASES) ?
+			"cache aliases" : "no aliases",
+		c->dcache.linesz);
+}
+
+static void probe_vcache(void)
+{
+	struct cpuinfo_mips *c = &current_cpu_data;
+	unsigned int config2, lsize;
+
+	if (current_cpu_type() != CPU_LOONGSON64)
+		return;
+
+	config2 = read_c0_config2();
+	if ((lsize = ((config2 >> 20) & 15)))
+		c->vcache.linesz = 2 << lsize;
+	else
+		c->vcache.linesz = lsize;
+
+	c->vcache.sets = 64 << ((config2 >> 24) & 15);
+	c->vcache.ways = 1 + ((config2 >> 16) & 15);
+
+	vcache_size = c->vcache.sets * c->vcache.ways * c->vcache.linesz;
+
+	c->vcache.waybit = 0;
+	c->vcache.waysize = vcache_size / c->vcache.ways;
+
+	pr_info("Unified victim cache %ldkB %s, linesize %d bytes.\n",
+		vcache_size >> 10, way_string[c->vcache.ways], c->vcache.linesz);
+}
+
+/*
+ * If you even _breathe_ on this function, look at the gcc output and make sure
+ * it does not pop things on and off the stack for the cache sizing loop that
+ * executes in KSEG1 space or else you will crash and burn badly.  You have
+ * been warned.
+ */
+static int probe_scache(void)
+{
+	unsigned long flags, addr, begin, end, pow2;
+	unsigned int config = read_c0_config();
+	struct cpuinfo_mips *c = &current_cpu_data;
+
+	if (config & CONF_SC)
+		return 0;
+
+	begin = (unsigned long) &_stext;
+	begin &= ~((4 * 1024 * 1024) - 1);
+	end = begin + (4 * 1024 * 1024);
+
+	/*
+	 * This is such a bitch, you'd think they would make it easy to do
+	 * this.  Away you daemons of stupidity!
+	 */
+	local_irq_save(flags);
+
+	/* Fill each size-multiple cache line with a valid tag. */
+	pow2 = (64 * 1024);
+	for (addr = begin; addr < end; addr = (begin + pow2)) {
+		unsigned long *p = (unsigned long *) addr;
+		__asm__ __volatile__("nop" : : "r" (*p)); /* whee... */
+		pow2 <<= 1;
+	}
+
+	/* Load first line with zero (therefore invalid) tag. */
+	write_c0_taglo(0);
+	write_c0_taghi(0);
+	__asm__ __volatile__("nop; nop; nop; nop;"); /* avoid the hazard */
+	cache_op(Index_Store_Tag_I, begin);
+	cache_op(Index_Store_Tag_D, begin);
+	cache_op(Index_Store_Tag_SD, begin);
+
+	/* Now search for the wrap around point. */
+	pow2 = (128 * 1024);
+	for (addr = begin + (128 * 1024); addr < end; addr = begin + pow2) {
+		cache_op(Index_Load_Tag_SD, addr);
+		__asm__ __volatile__("nop; nop; nop; nop;"); /* hazard... */
+		if (!read_c0_taglo())
+			break;
+		pow2 <<= 1;
+	}
+	local_irq_restore(flags);
+	addr -= begin;
+
+	scache_size = addr;
+	c->scache.linesz = 16 << ((config & R4K_CONF_SB) >> 22);
+	c->scache.ways = 1;
+	c->scache.waybit = 0;		/* does not matter */
+
+	return 1;
+}
+
+static void loongson2_sc_init(void)
+{
+	struct cpuinfo_mips *c = &current_cpu_data;
+
+	scache_size = 512*1024;
+	c->scache.linesz = 32;
+	c->scache.ways = 4;
+	c->scache.waybit = 0;
+	c->scache.waysize = scache_size / (c->scache.ways);
+	c->scache.sets = scache_size / (c->scache.linesz * c->scache.ways);
+	pr_info("Unified secondary cache %ldkB %s, linesize %d bytes.\n",
+	       scache_size >> 10, way_string[c->scache.ways], c->scache.linesz);
+
+	c->options |= MIPS_CPU_INCLUSIVE_CACHES;
+}
+
+static void loongson3_sc_init(void)
+{
+	struct cpuinfo_mips *c = &current_cpu_data;
+	unsigned int config2, lsize;
+
+	config2 = read_c0_config2();
+	lsize = (config2 >> 4) & 15;
+	if (lsize)
+		c->scache.linesz = 2 << lsize;
+	else
+		c->scache.linesz = 0;
+	c->scache.sets = 64 << ((config2 >> 8) & 15);
+	c->scache.ways = 1 + (config2 & 15);
+
+	/* Loongson-3 has 4-Scache banks, while Loongson-2K have only 2 banks */
+	if ((c->processor_id & PRID_IMP_MASK) == PRID_IMP_LOONGSON_64R)
+		c->scache.sets *= 2;
+	else
+		c->scache.sets *= 4;
+
+	scache_size = c->scache.sets * c->scache.ways * c->scache.linesz;
+
+	c->scache.waybit = 0;
+	c->scache.waysize = scache_size / c->scache.ways;
+	pr_info("Unified secondary cache %ldkB %s, linesize %d bytes.\n",
+	       scache_size >> 10, way_string[c->scache.ways], c->scache.linesz);
+	if (scache_size)
+		c->options |= MIPS_CPU_INCLUSIVE_CACHES;
+	return;
+}
+
+extern int r5k_sc_init(void);
+extern int rm7k_sc_init(void);
+extern int mips_sc_init(void);
+
+static void setup_scache(void)
+{
+	struct cpuinfo_mips *c = &current_cpu_data;
+	unsigned int config = read_c0_config();
+	int sc_present = 0;
+
+	/*
+	 * Do the probing thing on R4000SC and R4400SC processors.  Other
+	 * processors don't have a S-cache that would be relevant to the
+	 * Linux memory management.
+	 */
+	switch (current_cpu_type()) {
+	case CPU_R4000SC:
+	case CPU_R4000MC:
+	case CPU_R4400SC:
+	case CPU_R4400MC:
+		sc_present = run_uncached(probe_scache);
+		if (sc_present)
+			c->options |= MIPS_CPU_CACHE_CDEX_S;
+		break;
+
+	case CPU_R10000:
+	case CPU_R12000:
+	case CPU_R14000:
+	case CPU_R16000:
+		scache_size = 0x80000 << ((config & R10K_CONF_SS) >> 16);
+		c->scache.linesz = 64 << ((config >> 13) & 1);
+		c->scache.ways = 2;
+		c->scache.waybit= 0;
+		sc_present = 1;
+		break;
+
+	case CPU_R5000:
+	case CPU_NEVADA:
+#ifdef CONFIG_R5000_CPU_SCACHE
+		r5k_sc_init();
+#endif
+		return;
+
+	case CPU_RM7000:
+#ifdef CONFIG_RM7000_CPU_SCACHE
+		rm7k_sc_init();
+#endif
+		return;
+
+	case CPU_LOONGSON2EF:
+		loongson2_sc_init();
+		return;
+
+	case CPU_LOONGSON64:
+		loongson3_sc_init();
+		return;
+
+	case CPU_CAVIUM_OCTEON3:
+		/* don't need to worry about L2, fully coherent */
+		return;
+
+	default:
+		if (c->isa_level & (MIPS_CPU_ISA_M32R1 | MIPS_CPU_ISA_M64R1 |
+				    MIPS_CPU_ISA_M32R2 | MIPS_CPU_ISA_M64R2 |
+				    MIPS_CPU_ISA_M32R5 | MIPS_CPU_ISA_M64R5 |
+				    MIPS_CPU_ISA_M32R6 | MIPS_CPU_ISA_M64R6)) {
+#ifdef CONFIG_MIPS_CPU_SCACHE
+			if (mips_sc_init ()) {
+				scache_size = c->scache.ways * c->scache.sets * c->scache.linesz;
+				printk("MIPS secondary cache %ldkB, %s, linesize %d bytes.\n",
+				       scache_size >> 10,
+				       way_string[c->scache.ways], c->scache.linesz);
+
+				if (current_cpu_type() == CPU_BMIPS5000)
+					c->options |= MIPS_CPU_INCLUSIVE_CACHES;
+			}
+
+#else
+			if (!(c->scache.flags & MIPS_CACHE_NOT_PRESENT))
+				panic("Dunno how to handle MIPS32 / MIPS64 second level cache");
+#endif
+			return;
+		}
+		sc_present = 0;
+	}
+
+	if (!sc_present)
+		return;
+
+	/* compute a couple of other cache variables */
+	c->scache.waysize = scache_size / c->scache.ways;
+
+	c->scache.sets = scache_size / (c->scache.linesz * c->scache.ways);
+
+	printk("Unified secondary cache %ldkB %s, linesize %d bytes.\n",
+	       scache_size >> 10, way_string[c->scache.ways], c->scache.linesz);
+
+	c->options |= MIPS_CPU_INCLUSIVE_CACHES;
+}
+
+void au1x00_fixup_config_od(void)
+{
+	/*
+	 * c0_config.od (bit 19) was write only (and read as 0)
+	 * on the early revisions of Alchemy SOCs.  It disables the bus
+	 * transaction overlapping and needs to be set to fix various errata.
+	 */
+	switch (read_c0_prid()) {
+	case 0x00030100: /* Au1000 DA */
+	case 0x00030201: /* Au1000 HA */
+	case 0x00030202: /* Au1000 HB */
+	case 0x01030200: /* Au1500 AB */
+	/*
+	 * Au1100 errata actually keeps silence about this bit, so we set it
+	 * just in case for those revisions that require it to be set according
+	 * to the (now gone) cpu table.
+	 */
+	case 0x02030200: /* Au1100 AB */
+	case 0x02030201: /* Au1100 BA */
+	case 0x02030202: /* Au1100 BC */
+		set_c0_config(1 << 19);
+		break;
+	}
+}
+
+/* CP0 hazard avoidance. */
+#define NXP_BARRIER()							\
+	 __asm__ __volatile__(						\
+	".set noreorder\n\t"						\
+	"nop; nop; nop; nop; nop; nop;\n\t"				\
+	".set reorder\n\t")
+
+static void nxp_pr4450_fixup_config(void)
+{
+	unsigned long config0;
+
+	config0 = read_c0_config();
+
+	/* clear all three cache coherency fields */
+	config0 &= ~(0x7 | (7 << 25) | (7 << 28));
+	config0 |= (((_page_cachable_default >> _CACHE_SHIFT) <<  0) |
+		    ((_page_cachable_default >> _CACHE_SHIFT) << 25) |
+		    ((_page_cachable_default >> _CACHE_SHIFT) << 28));
+	write_c0_config(config0);
+	NXP_BARRIER();
+}
+
+static int cca = -1;
+
+static int __init cca_setup(char *str)
+{
+	get_option(&str, &cca);
+
+	return 0;
+}
+
+early_param("cca", cca_setup);
+
+static void coherency_setup(void)
+{
+	if (cca < 0 || cca > 7)
+		cca = read_c0_config() & CONF_CM_CMASK;
+	_page_cachable_default = cca << _CACHE_SHIFT;
+
+	pr_debug("Using cache attribute %d\n", cca);
+	change_c0_config(CONF_CM_CMASK, cca);
+
+	/*
+	 * c0_status.cu=0 specifies that updates by the sc instruction use
+	 * the coherency mode specified by the TLB; 1 means cachable
+	 * coherent update on write will be used.  Not all processors have
+	 * this bit and; some wire it to zero, others like Toshiba had the
+	 * silly idea of putting something else there ...
+	 */
+	switch (current_cpu_type()) {
+	case CPU_R4000PC:
+	case CPU_R4000SC:
+	case CPU_R4000MC:
+	case CPU_R4400PC:
+	case CPU_R4400SC:
+	case CPU_R4400MC:
+		clear_c0_config(CONF_CU);
+		break;
+	/*
+	 * We need to catch the early Alchemy SOCs with
+	 * the write-only co_config.od bit and set it back to one on:
+	 * Au1000 rev DA, HA, HB;  Au1100 AB, BA, BC, Au1500 AB
+	 */
+	case CPU_ALCHEMY:
+		au1x00_fixup_config_od();
+		break;
+
+	case PRID_IMP_PR4450:
+		nxp_pr4450_fixup_config();
+		break;
+	}
+}
+
+static void r4k_cache_error_setup(void)
+{
+	extern char __weak except_vec2_generic;
+	extern char __weak except_vec2_sb1;
+
+	switch (current_cpu_type()) {
+	case CPU_SB1:
+	case CPU_SB1A:
+		set_uncached_handler(0x100, &except_vec2_sb1, 0x80);
+		break;
+
+	default:
+		set_uncached_handler(0x100, &except_vec2_generic, 0x80);
+		break;
+	}
+}
+
+void r4k_cache_init(void)
+{
+	extern void build_clear_page(void);
+	extern void build_copy_page(void);
+	struct cpuinfo_mips *c = &current_cpu_data;
+
+	probe_pcache();
+	probe_vcache();
+	setup_scache();
+
+	r4k_blast_dcache_page_setup();
+	r4k_blast_dcache_page_indexed_setup();
+	r4k_blast_dcache_setup();
+	r4k_blast_icache_page_setup();
+	r4k_blast_icache_page_indexed_setup();
+	r4k_blast_icache_setup();
+	r4k_blast_scache_page_setup();
+	r4k_blast_scache_page_indexed_setup();
+	r4k_blast_scache_setup();
+	r4k_blast_scache_node_setup();
+#ifdef CONFIG_EVA
+	r4k_blast_dcache_user_page_setup();
+	r4k_blast_icache_user_page_setup();
+#endif
+
+	/*
+	 * Some MIPS32 and MIPS64 processors have physically indexed caches.
+	 * This code supports virtually indexed processors and will be
+	 * unnecessarily inefficient on physically indexed processors.
+	 */
+	if (c->dcache.linesz && cpu_has_dc_aliases)
+		shm_align_mask = max_t( unsigned long,
+					c->dcache.sets * c->dcache.linesz - 1,
+					PAGE_SIZE - 1);
+	else
+		shm_align_mask = PAGE_SIZE-1;
+
+	__flush_cache_vmap	= r4k__flush_cache_vmap;
+	__flush_cache_vunmap	= r4k__flush_cache_vunmap;
+
+	flush_cache_all		= cache_noop;
+	__flush_cache_all	= r4k___flush_cache_all;
+	flush_cache_mm		= r4k_flush_cache_mm;
+	flush_cache_page	= r4k_flush_cache_page;
+	flush_cache_range	= r4k_flush_cache_range;
+
+	__flush_kernel_vmap_range = r4k_flush_kernel_vmap_range;
+
+	flush_icache_all	= r4k_flush_icache_all;
+	local_flush_data_cache_page	= local_r4k_flush_data_cache_page;
+	flush_data_cache_page	= r4k_flush_data_cache_page;
+	flush_icache_range	= r4k_flush_icache_range;
+	local_flush_icache_range	= local_r4k_flush_icache_range;
+	__flush_icache_user_range	= r4k_flush_icache_user_range;
+	__local_flush_icache_user_range	= local_r4k_flush_icache_user_range;
+
+#ifdef CONFIG_DMA_NONCOHERENT
+	if (dma_default_coherent) {
+		_dma_cache_wback_inv	= (void *)cache_noop;
+		_dma_cache_wback	= (void *)cache_noop;
+		_dma_cache_inv		= (void *)cache_noop;
+	} else {
+		_dma_cache_wback_inv	= r4k_dma_cache_wback_inv;
+		_dma_cache_wback	= r4k_dma_cache_wback_inv;
+		_dma_cache_inv		= r4k_dma_cache_inv;
+	}
+#endif /* CONFIG_DMA_NONCOHERENT */
+
+	build_clear_page();
+	build_copy_page();
+
+	/*
+	 * We want to run CMP kernels on core with and without coherent
+	 * caches. Therefore, do not use CONFIG_MIPS_CMP to decide whether
+	 * or not to flush caches.
+	 */
+	local_r4k___flush_cache_all(NULL);
+
+	coherency_setup();
+	board_cache_error_setup = r4k_cache_error_setup;
+
+	/*
+	 * Per-CPU overrides
+	 */
+	switch (current_cpu_type()) {
+	case CPU_BMIPS4350:
+	case CPU_BMIPS4380:
+		/* No IPI is needed because all CPUs share the same D$ */
+		flush_data_cache_page = r4k_blast_dcache_page;
+		break;
+	case CPU_BMIPS5000:
+		/* We lose our superpowers if L2 is disabled */
+		if (c->scache.flags & MIPS_CACHE_NOT_PRESENT)
+			break;
+
+		/* I$ fills from D$ just by emptying the write buffers */
+		flush_cache_page = (void *)b5k_instruction_hazard;
+		flush_cache_range = (void *)b5k_instruction_hazard;
+		local_flush_data_cache_page = (void *)b5k_instruction_hazard;
+		flush_data_cache_page = (void *)b5k_instruction_hazard;
+		flush_icache_range = (void *)b5k_instruction_hazard;
+		local_flush_icache_range = (void *)b5k_instruction_hazard;
+
+
+		/* Optimization: an L2 flush implicitly flushes the L1 */
+		current_cpu_data.options |= MIPS_CPU_INCLUSIVE_CACHES;
+		break;
+	case CPU_LOONGSON64:
+		/* Loongson-3 maintains cache coherency by hardware */
+		__flush_cache_all	= cache_noop;
+		__flush_cache_vmap	= cache_noop;
+		__flush_cache_vunmap	= cache_noop;
+		__flush_kernel_vmap_range = (void *)cache_noop;
+		flush_cache_mm		= (void *)cache_noop;
+		flush_cache_page	= (void *)cache_noop;
+		flush_cache_range	= (void *)cache_noop;
+		flush_icache_all	= (void *)cache_noop;
+		flush_data_cache_page	= (void *)cache_noop;
+		local_flush_data_cache_page	= (void *)cache_noop;
+		break;
+	}
+}
+
+static int r4k_cache_pm_notifier(struct notifier_block *self, unsigned long cmd,
+			       void *v)
+{
+	switch (cmd) {
+	case CPU_PM_ENTER_FAILED:
+	case CPU_PM_EXIT:
+		coherency_setup();
+		break;
+	}
+
+	return NOTIFY_OK;
+}
+
+static struct notifier_block r4k_cache_pm_notifier_block = {
+	.notifier_call = r4k_cache_pm_notifier,
+};
+
+int __init r4k_cache_init_pm(void)
+{
+	return cpu_pm_register_notifier(&r4k_cache_pm_notifier_block);
+}
+arch_initcall(r4k_cache_init_pm);
diff --git a/arch/mips/mm/cache.c b/arch/mips/mm/cache.c
new file mode 100644
index 000000000..11b3e7dda
--- /dev/null
+++ b/arch/mips/mm/cache.c
@@ -0,0 +1,209 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994 - 2003, 06, 07 by Ralf Baechle (ralf@linux-mips.org)
+ * Copyright (C) 2007 MIPS Technologies, Inc.
+ */
+#include <linux/fs.h>
+#include <linux/fcntl.h>
+#include <linux/kernel.h>
+#include <linux/linkage.h>
+#include <linux/export.h>
+#include <linux/sched.h>
+#include <linux/syscalls.h>
+#include <linux/mm.h>
+#include <linux/highmem.h>
+#include <linux/pagemap.h>
+
+#include <asm/cacheflush.h>
+#include <asm/processor.h>
+#include <asm/cpu.h>
+#include <asm/cpu-features.h>
+#include <asm/setup.h>
+#include <asm/pgtable.h>
+
+/* Cache operations. */
+void (*flush_cache_all)(void);
+void (*__flush_cache_all)(void);
+EXPORT_SYMBOL_GPL(__flush_cache_all);
+void (*flush_cache_mm)(struct mm_struct *mm);
+void (*flush_cache_range)(struct vm_area_struct *vma, unsigned long start,
+	unsigned long end);
+void (*flush_cache_page)(struct vm_area_struct *vma, unsigned long page,
+	unsigned long pfn);
+void (*flush_icache_range)(unsigned long start, unsigned long end);
+EXPORT_SYMBOL_GPL(flush_icache_range);
+void (*local_flush_icache_range)(unsigned long start, unsigned long end);
+EXPORT_SYMBOL_GPL(local_flush_icache_range);
+void (*__flush_icache_user_range)(unsigned long start, unsigned long end);
+void (*__local_flush_icache_user_range)(unsigned long start, unsigned long end);
+EXPORT_SYMBOL_GPL(__local_flush_icache_user_range);
+
+void (*__flush_cache_vmap)(void);
+void (*__flush_cache_vunmap)(void);
+
+void (*__flush_kernel_vmap_range)(unsigned long vaddr, int size);
+EXPORT_SYMBOL_GPL(__flush_kernel_vmap_range);
+
+/* MIPS specific cache operations */
+void (*local_flush_data_cache_page)(void * addr);
+void (*flush_data_cache_page)(unsigned long addr);
+void (*flush_icache_all)(void);
+
+EXPORT_SYMBOL_GPL(local_flush_data_cache_page);
+EXPORT_SYMBOL(flush_data_cache_page);
+EXPORT_SYMBOL(flush_icache_all);
+
+#ifdef CONFIG_DMA_NONCOHERENT
+
+/* DMA cache operations. */
+void (*_dma_cache_wback_inv)(unsigned long start, unsigned long size);
+void (*_dma_cache_wback)(unsigned long start, unsigned long size);
+void (*_dma_cache_inv)(unsigned long start, unsigned long size);
+
+#endif /* CONFIG_DMA_NONCOHERENT */
+
+/*
+ * We could optimize the case where the cache argument is not BCACHE but
+ * that seems very atypical use ...
+ */
+SYSCALL_DEFINE3(cacheflush, unsigned long, addr, unsigned long, bytes,
+	unsigned int, cache)
+{
+	if (bytes == 0)
+		return 0;
+	if (!access_ok((void __user *) addr, bytes))
+		return -EFAULT;
+
+	__flush_icache_user_range(addr, addr + bytes);
+
+	return 0;
+}
+
+void __flush_dcache_page(struct page *page)
+{
+	struct address_space *mapping = page_mapping_file(page);
+	unsigned long addr;
+
+	if (mapping && !mapping_mapped(mapping)) {
+		SetPageDcacheDirty(page);
+		return;
+	}
+
+	/*
+	 * We could delay the flush for the !page_mapping case too.  But that
+	 * case is for exec env/arg pages and those are %99 certainly going to
+	 * get faulted into the tlb (and thus flushed) anyways.
+	 */
+	if (PageHighMem(page))
+		addr = (unsigned long)kmap_atomic(page);
+	else
+		addr = (unsigned long)page_address(page);
+
+	flush_data_cache_page(addr);
+
+	if (PageHighMem(page))
+		kunmap_atomic((void *)addr);
+}
+
+EXPORT_SYMBOL(__flush_dcache_page);
+
+void __flush_anon_page(struct page *page, unsigned long vmaddr)
+{
+	unsigned long addr = (unsigned long) page_address(page);
+
+	if (pages_do_alias(addr, vmaddr)) {
+		if (page_mapcount(page) && !Page_dcache_dirty(page)) {
+			void *kaddr;
+
+			kaddr = kmap_coherent(page, vmaddr);
+			flush_data_cache_page((unsigned long)kaddr);
+			kunmap_coherent();
+		} else
+			flush_data_cache_page(addr);
+	}
+}
+
+EXPORT_SYMBOL(__flush_anon_page);
+
+void __update_cache(unsigned long address, pte_t pte)
+{
+	struct page *page;
+	unsigned long pfn, addr;
+	int exec = !pte_no_exec(pte) && !cpu_has_ic_fills_f_dc;
+
+	pfn = pte_pfn(pte);
+	if (unlikely(!pfn_valid(pfn)))
+		return;
+	page = pfn_to_page(pfn);
+	if (Page_dcache_dirty(page)) {
+		if (PageHighMem(page))
+			addr = (unsigned long)kmap_atomic(page);
+		else
+			addr = (unsigned long)page_address(page);
+
+		if (exec || pages_do_alias(addr, address & PAGE_MASK))
+			flush_data_cache_page(addr);
+
+		if (PageHighMem(page))
+			kunmap_atomic((void *)addr);
+
+		ClearPageDcacheDirty(page);
+	}
+}
+
+unsigned long _page_cachable_default;
+EXPORT_SYMBOL(_page_cachable_default);
+
+#define PM(p)	__pgprot(_page_cachable_default | (p))
+
+static pgprot_t protection_map[16] __ro_after_init;
+DECLARE_VM_GET_PAGE_PROT
+
+static inline void setup_protection_map(void)
+{
+	protection_map[0]  = PM(_PAGE_PRESENT | _PAGE_NO_EXEC | _PAGE_NO_READ);
+	protection_map[1]  = PM(_PAGE_PRESENT | _PAGE_NO_EXEC);
+	protection_map[2]  = PM(_PAGE_PRESENT | _PAGE_NO_EXEC | _PAGE_NO_READ);
+	protection_map[3]  = PM(_PAGE_PRESENT | _PAGE_NO_EXEC);
+	protection_map[4]  = PM(_PAGE_PRESENT);
+	protection_map[5]  = PM(_PAGE_PRESENT);
+	protection_map[6]  = PM(_PAGE_PRESENT);
+	protection_map[7]  = PM(_PAGE_PRESENT);
+
+	protection_map[8]  = PM(_PAGE_PRESENT | _PAGE_NO_EXEC | _PAGE_NO_READ);
+	protection_map[9]  = PM(_PAGE_PRESENT | _PAGE_NO_EXEC);
+	protection_map[10] = PM(_PAGE_PRESENT | _PAGE_NO_EXEC | _PAGE_WRITE |
+				_PAGE_NO_READ);
+	protection_map[11] = PM(_PAGE_PRESENT | _PAGE_NO_EXEC | _PAGE_WRITE);
+	protection_map[12] = PM(_PAGE_PRESENT);
+	protection_map[13] = PM(_PAGE_PRESENT);
+	protection_map[14] = PM(_PAGE_PRESENT | _PAGE_WRITE);
+	protection_map[15] = PM(_PAGE_PRESENT | _PAGE_WRITE);
+}
+
+#undef PM
+
+void cpu_cache_init(void)
+{
+	if (cpu_has_3k_cache) {
+		extern void __weak r3k_cache_init(void);
+
+		r3k_cache_init();
+	}
+	if (cpu_has_4k_cache) {
+		extern void __weak r4k_cache_init(void);
+
+		r4k_cache_init();
+	}
+
+	if (cpu_has_octeon_cache) {
+		extern void __weak octeon_cache_init(void);
+
+		octeon_cache_init();
+	}
+
+	setup_protection_map();
+}
diff --git a/arch/mips/mm/cerr-sb1.c b/arch/mips/mm/cerr-sb1.c
new file mode 100644
index 000000000..a3c02df19
--- /dev/null
+++ b/arch/mips/mm/cerr-sb1.c
@@ -0,0 +1,569 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2001,2002,2003 Broadcom Corporation
+ */
+#include <linux/sched.h>
+#include <asm/mipsregs.h>
+#include <asm/sibyte/sb1250.h>
+#include <asm/sibyte/sb1250_regs.h>
+
+#if !defined(CONFIG_SIBYTE_BUS_WATCHER) || defined(CONFIG_SIBYTE_BW_TRACE)
+#include <asm/io.h>
+#include <asm/sibyte/sb1250_scd.h>
+#endif
+
+/*
+ * We'd like to dump the L2_ECC_TAG register on errors, but errata make
+ * that unsafe... So for now we don't.	(BCM1250/BCM112x erratum SOC-48.)
+ */
+#undef DUMP_L2_ECC_TAG_ON_ERROR
+
+/* SB1 definitions */
+
+/* XXX should come from config1 XXX */
+#define SB1_CACHE_INDEX_MASK   0x1fe0
+
+#define CP0_ERRCTL_RECOVERABLE (1 << 31)
+#define CP0_ERRCTL_DCACHE      (1 << 30)
+#define CP0_ERRCTL_ICACHE      (1 << 29)
+#define CP0_ERRCTL_MULTIBUS    (1 << 23)
+#define CP0_ERRCTL_MC_TLB      (1 << 15)
+#define CP0_ERRCTL_MC_TIMEOUT  (1 << 14)
+
+#define CP0_CERRI_TAG_PARITY   (1 << 29)
+#define CP0_CERRI_DATA_PARITY  (1 << 28)
+#define CP0_CERRI_EXTERNAL     (1 << 26)
+
+#define CP0_CERRI_IDX_VALID(c) (!((c) & CP0_CERRI_EXTERNAL))
+#define CP0_CERRI_DATA	       (CP0_CERRI_DATA_PARITY)
+
+#define CP0_CERRD_MULTIPLE     (1 << 31)
+#define CP0_CERRD_TAG_STATE    (1 << 30)
+#define CP0_CERRD_TAG_ADDRESS  (1 << 29)
+#define CP0_CERRD_DATA_SBE     (1 << 28)
+#define CP0_CERRD_DATA_DBE     (1 << 27)
+#define CP0_CERRD_EXTERNAL     (1 << 26)
+#define CP0_CERRD_LOAD	       (1 << 25)
+#define CP0_CERRD_STORE	       (1 << 24)
+#define CP0_CERRD_FILLWB       (1 << 23)
+#define CP0_CERRD_COHERENCY    (1 << 22)
+#define CP0_CERRD_DUPTAG       (1 << 21)
+
+#define CP0_CERRD_DPA_VALID(c) (!((c) & CP0_CERRD_EXTERNAL))
+#define CP0_CERRD_IDX_VALID(c) \
+   (((c) & (CP0_CERRD_LOAD | CP0_CERRD_STORE)) ? (!((c) & CP0_CERRD_EXTERNAL)) : 0)
+#define CP0_CERRD_CAUSES \
+   (CP0_CERRD_LOAD | CP0_CERRD_STORE | CP0_CERRD_FILLWB | CP0_CERRD_COHERENCY | CP0_CERRD_DUPTAG)
+#define CP0_CERRD_TYPES \
+   (CP0_CERRD_TAG_STATE | CP0_CERRD_TAG_ADDRESS | CP0_CERRD_DATA_SBE | CP0_CERRD_DATA_DBE | CP0_CERRD_EXTERNAL)
+#define CP0_CERRD_DATA	       (CP0_CERRD_DATA_SBE | CP0_CERRD_DATA_DBE)
+
+static uint32_t extract_ic(unsigned short addr, int data);
+static uint32_t extract_dc(unsigned short addr, int data);
+
+static inline void breakout_errctl(unsigned int val)
+{
+	if (val & CP0_ERRCTL_RECOVERABLE)
+		printk(" recoverable");
+	if (val & CP0_ERRCTL_DCACHE)
+		printk(" dcache");
+	if (val & CP0_ERRCTL_ICACHE)
+		printk(" icache");
+	if (val & CP0_ERRCTL_MULTIBUS)
+		printk(" multiple-buserr");
+	printk("\n");
+}
+
+static inline void breakout_cerri(unsigned int val)
+{
+	if (val & CP0_CERRI_TAG_PARITY)
+		printk(" tag-parity");
+	if (val & CP0_CERRI_DATA_PARITY)
+		printk(" data-parity");
+	if (val & CP0_CERRI_EXTERNAL)
+		printk(" external");
+	printk("\n");
+}
+
+static inline void breakout_cerrd(unsigned int val)
+{
+	switch (val & CP0_CERRD_CAUSES) {
+	case CP0_CERRD_LOAD:
+		printk(" load,");
+		break;
+	case CP0_CERRD_STORE:
+		printk(" store,");
+		break;
+	case CP0_CERRD_FILLWB:
+		printk(" fill/wb,");
+		break;
+	case CP0_CERRD_COHERENCY:
+		printk(" coherency,");
+		break;
+	case CP0_CERRD_DUPTAG:
+		printk(" duptags,");
+		break;
+	default:
+		printk(" NO CAUSE,");
+		break;
+	}
+	if (!(val & CP0_CERRD_TYPES))
+		printk(" NO TYPE");
+	else {
+		if (val & CP0_CERRD_MULTIPLE)
+			printk(" multi-err");
+		if (val & CP0_CERRD_TAG_STATE)
+			printk(" tag-state");
+		if (val & CP0_CERRD_TAG_ADDRESS)
+			printk(" tag-address");
+		if (val & CP0_CERRD_DATA_SBE)
+			printk(" data-SBE");
+		if (val & CP0_CERRD_DATA_DBE)
+			printk(" data-DBE");
+		if (val & CP0_CERRD_EXTERNAL)
+			printk(" external");
+	}
+	printk("\n");
+}
+
+#ifndef CONFIG_SIBYTE_BUS_WATCHER
+
+static void check_bus_watcher(void)
+{
+	uint32_t status, l2_err, memio_err;
+#ifdef DUMP_L2_ECC_TAG_ON_ERROR
+	uint64_t l2_tag;
+#endif
+
+	/* Destructive read, clears register and interrupt */
+	status = csr_in32(IOADDR(A_SCD_BUS_ERR_STATUS));
+	/* Bit 31 is always on, but there's no #define for that */
+	if (status & ~(1UL << 31)) {
+		l2_err = csr_in32(IOADDR(A_BUS_L2_ERRORS));
+#ifdef DUMP_L2_ECC_TAG_ON_ERROR
+		l2_tag = in64(IOADDR(A_L2_ECC_TAG));
+#endif
+		memio_err = csr_in32(IOADDR(A_BUS_MEM_IO_ERRORS));
+		printk("Bus watcher error counters: %08x %08x\n", l2_err, memio_err);
+		printk("\nLast recorded signature:\n");
+		printk("Request %02x from %d, answered by %d with Dcode %d\n",
+		       (unsigned int)(G_SCD_BERR_TID(status) & 0x3f),
+		       (int)(G_SCD_BERR_TID(status) >> 6),
+		       (int)G_SCD_BERR_RID(status),
+		       (int)G_SCD_BERR_DCODE(status));
+#ifdef DUMP_L2_ECC_TAG_ON_ERROR
+		printk("Last L2 tag w/ bad ECC: %016llx\n", l2_tag);
+#endif
+	} else {
+		printk("Bus watcher indicates no error\n");
+	}
+}
+#else
+extern void check_bus_watcher(void);
+#endif
+
+asmlinkage void sb1_cache_error(void)
+{
+	uint32_t errctl, cerr_i, cerr_d, dpalo, dpahi, eepc, res;
+	unsigned long long cerr_dpa;
+
+#ifdef CONFIG_SIBYTE_BW_TRACE
+	/* Freeze the trace buffer now */
+	csr_out32(M_SCD_TRACE_CFG_FREEZE, IOADDR(A_SCD_TRACE_CFG));
+	printk("Trace buffer frozen\n");
+#endif
+
+	printk("Cache error exception on CPU %x:\n",
+	       (read_c0_prid() >> 25) & 0x7);
+
+	__asm__ __volatile__ (
+	"	.set	push\n\t"
+	"	.set	mips64\n\t"
+	"	.set	noat\n\t"
+	"	mfc0	%0, $26\n\t"
+	"	mfc0	%1, $27\n\t"
+	"	mfc0	%2, $27, 1\n\t"
+	"	dmfc0	$1, $27, 3\n\t"
+	"	dsrl32	%3, $1, 0 \n\t"
+	"	sll	%4, $1, 0 \n\t"
+	"	mfc0	%5, $30\n\t"
+	"	.set	pop"
+	: "=r" (errctl), "=r" (cerr_i), "=r" (cerr_d),
+	  "=r" (dpahi), "=r" (dpalo), "=r" (eepc));
+
+	cerr_dpa = (((uint64_t)dpahi) << 32) | dpalo;
+	printk(" c0_errorepc ==	  %08x\n", eepc);
+	printk(" c0_errctl   ==	  %08x", errctl);
+	breakout_errctl(errctl);
+	if (errctl & CP0_ERRCTL_ICACHE) {
+		printk(" c0_cerr_i   ==	  %08x", cerr_i);
+		breakout_cerri(cerr_i);
+		if (CP0_CERRI_IDX_VALID(cerr_i)) {
+			/* Check index of EPC, allowing for delay slot */
+			if (((eepc & SB1_CACHE_INDEX_MASK) != (cerr_i & SB1_CACHE_INDEX_MASK)) &&
+			    ((eepc & SB1_CACHE_INDEX_MASK) != ((cerr_i & SB1_CACHE_INDEX_MASK) - 4)))
+				printk(" cerr_i idx doesn't match eepc\n");
+			else {
+				res = extract_ic(cerr_i & SB1_CACHE_INDEX_MASK,
+						 (cerr_i & CP0_CERRI_DATA) != 0);
+				if (!(res & cerr_i))
+					printk("...didn't see indicated icache problem\n");
+			}
+		}
+	}
+	if (errctl & CP0_ERRCTL_DCACHE) {
+		printk(" c0_cerr_d   ==	  %08x", cerr_d);
+		breakout_cerrd(cerr_d);
+		if (CP0_CERRD_DPA_VALID(cerr_d)) {
+			printk(" c0_cerr_dpa == %010llx\n", cerr_dpa);
+			if (!CP0_CERRD_IDX_VALID(cerr_d)) {
+				res = extract_dc(cerr_dpa & SB1_CACHE_INDEX_MASK,
+						 (cerr_d & CP0_CERRD_DATA) != 0);
+				if (!(res & cerr_d))
+					printk("...didn't see indicated dcache problem\n");
+			} else {
+				if ((cerr_dpa & SB1_CACHE_INDEX_MASK) != (cerr_d & SB1_CACHE_INDEX_MASK))
+					printk(" cerr_d idx doesn't match cerr_dpa\n");
+				else {
+					res = extract_dc(cerr_d & SB1_CACHE_INDEX_MASK,
+							 (cerr_d & CP0_CERRD_DATA) != 0);
+					if (!(res & cerr_d))
+						printk("...didn't see indicated problem\n");
+				}
+			}
+		}
+	}
+
+	check_bus_watcher();
+
+	/*
+	 * Calling panic() when a fatal cache error occurs scrambles the
+	 * state of the system (and the cache), making it difficult to
+	 * investigate after the fact.	However, if you just stall the CPU,
+	 * the other CPU may keep on running, which is typically very
+	 * undesirable.
+	 */
+#ifdef CONFIG_SB1_CERR_STALL
+	while (1)
+		;
+#else
+	panic("unhandled cache error");
+#endif
+}
+
+
+/* Parity lookup table. */
+static const uint8_t parity[256] = {
+	0, 1, 1, 0, 1, 0, 0, 1, 1, 0, 0, 1, 0, 1, 1, 0,
+	1, 0, 0, 1, 0, 1, 1, 0, 0, 1, 1, 0, 1, 0, 0, 1,
+	1, 0, 0, 1, 0, 1, 1, 0, 0, 1, 1, 0, 1, 0, 0, 1,
+	0, 1, 1, 0, 1, 0, 0, 1, 1, 0, 0, 1, 0, 1, 1, 0,
+	1, 0, 0, 1, 0, 1, 1, 0, 0, 1, 1, 0, 1, 0, 0, 1,
+	0, 1, 1, 0, 1, 0, 0, 1, 1, 0, 0, 1, 0, 1, 1, 0,
+	0, 1, 1, 0, 1, 0, 0, 1, 1, 0, 0, 1, 0, 1, 1, 0,
+	1, 0, 0, 1, 0, 1, 1, 0, 0, 1, 1, 0, 1, 0, 0, 1,
+	1, 0, 0, 1, 0, 1, 1, 0, 0, 1, 1, 0, 1, 0, 0, 1,
+	0, 1, 1, 0, 1, 0, 0, 1, 1, 0, 0, 1, 0, 1, 1, 0,
+	0, 1, 1, 0, 1, 0, 0, 1, 1, 0, 0, 1, 0, 1, 1, 0,
+	1, 0, 0, 1, 0, 1, 1, 0, 0, 1, 1, 0, 1, 0, 0, 1,
+	0, 1, 1, 0, 1, 0, 0, 1, 1, 0, 0, 1, 0, 1, 1, 0,
+	1, 0, 0, 1, 0, 1, 1, 0, 0, 1, 1, 0, 1, 0, 0, 1,
+	1, 0, 0, 1, 0, 1, 1, 0, 0, 1, 1, 0, 1, 0, 0, 1,
+	0, 1, 1, 0, 1, 0, 0, 1, 1, 0, 0, 1, 0, 1, 1, 0
+};
+
+/* Masks to select bits for Hamming parity, mask_72_64[i] for bit[i] */
+static const uint64_t mask_72_64[8] = {
+	0x0738C808099264FFULL,
+	0x38C808099264FF07ULL,
+	0xC808099264FF0738ULL,
+	0x08099264FF0738C8ULL,
+	0x099264FF0738C808ULL,
+	0x9264FF0738C80809ULL,
+	0x64FF0738C8080992ULL,
+	0xFF0738C808099264ULL
+};
+
+/* Calculate the parity on a range of bits */
+static char range_parity(uint64_t dword, int max, int min)
+{
+	char parity = 0;
+	int i;
+	dword >>= min;
+	for (i=max-min; i>=0; i--) {
+		if (dword & 0x1)
+			parity = !parity;
+		dword >>= 1;
+	}
+	return parity;
+}
+
+/* Calculate the 4-bit even byte-parity for an instruction */
+static unsigned char inst_parity(uint32_t word)
+{
+	int i, j;
+	char parity = 0;
+	for (j=0; j<4; j++) {
+		char byte_parity = 0;
+		for (i=0; i<8; i++) {
+			if (word & 0x80000000)
+				byte_parity = !byte_parity;
+			word <<= 1;
+		}
+		parity <<= 1;
+		parity |= byte_parity;
+	}
+	return parity;
+}
+
+static uint32_t extract_ic(unsigned short addr, int data)
+{
+	unsigned short way;
+	int valid;
+	uint32_t taghi, taglolo, taglohi;
+	unsigned long long taglo, va;
+	uint64_t tlo_tmp;
+	uint8_t lru;
+	int res = 0;
+
+	printk("Icache index 0x%04x  ", addr);
+	for (way = 0; way < 4; way++) {
+		/* Index-load-tag-I */
+		__asm__ __volatile__ (
+		"	.set	push		\n\t"
+		"	.set	noreorder	\n\t"
+		"	.set	mips64		\n\t"
+		"	.set	noat		\n\t"
+		"	cache	4, 0(%3)	\n\t"
+		"	mfc0	%0, $29		\n\t"
+		"	dmfc0	$1, $28		\n\t"
+		"	dsrl32	%1, $1, 0	\n\t"
+		"	sll	%2, $1, 0	\n\t"
+		"	.set	pop"
+		: "=r" (taghi), "=r" (taglohi), "=r" (taglolo)
+		: "r" ((way << 13) | addr));
+
+		taglo = ((unsigned long long)taglohi << 32) | taglolo;
+		if (way == 0) {
+			lru = (taghi >> 14) & 0xff;
+			printk("[Bank %d Set 0x%02x]  LRU > %d %d %d %d > MRU\n",
+				    ((addr >> 5) & 0x3), /* bank */
+				    ((addr >> 7) & 0x3f), /* index */
+				    (lru & 0x3),
+				    ((lru >> 2) & 0x3),
+				    ((lru >> 4) & 0x3),
+				    ((lru >> 6) & 0x3));
+		}
+		va = (taglo & 0xC0000FFFFFFFE000ULL) | addr;
+		if ((taglo & (1 << 31)) && (((taglo >> 62) & 0x3) == 3))
+			va |= 0x3FFFF00000000000ULL;
+		valid = ((taghi >> 29) & 1);
+		if (valid) {
+			tlo_tmp = taglo & 0xfff3ff;
+			if (((taglo >> 10) & 1) ^ range_parity(tlo_tmp, 23, 0)) {
+				printk("   ** bad parity in VTag0/G/ASID\n");
+				res |= CP0_CERRI_TAG_PARITY;
+			}
+			if (((taglo >> 11) & 1) ^ range_parity(taglo, 63, 24)) {
+				printk("   ** bad parity in R/VTag1\n");
+				res |= CP0_CERRI_TAG_PARITY;
+			}
+		}
+		if (valid ^ ((taghi >> 27) & 1)) {
+			printk("   ** bad parity for valid bit\n");
+			res |= CP0_CERRI_TAG_PARITY;
+		}
+		printk(" %d  [VA %016llx]  [Vld? %d]  raw tags: %08X-%016llX\n",
+			    way, va, valid, taghi, taglo);
+
+		if (data) {
+			uint32_t datahi, insta, instb;
+			uint8_t predecode;
+			int offset;
+
+			/* (hit all banks and ways) */
+			for (offset = 0; offset < 4; offset++) {
+				/* Index-load-data-I */
+				__asm__ __volatile__ (
+				"	.set	push\n\t"
+				"	.set	noreorder\n\t"
+				"	.set	mips64\n\t"
+				"	.set	noat\n\t"
+				"	cache	6, 0(%3)  \n\t"
+				"	mfc0	%0, $29, 1\n\t"
+				"	dmfc0  $1, $28, 1\n\t"
+				"	dsrl32 %1, $1, 0 \n\t"
+				"	sll    %2, $1, 0 \n\t"
+				"	.set	pop	    \n"
+				: "=r" (datahi), "=r" (insta), "=r" (instb)
+				: "r" ((way << 13) | addr | (offset << 3)));
+				predecode = (datahi >> 8) & 0xff;
+				if (((datahi >> 16) & 1) != (uint32_t)range_parity(predecode, 7, 0)) {
+					printk("   ** bad parity in predecode\n");
+					res |= CP0_CERRI_DATA_PARITY;
+				}
+				/* XXXKW should/could check predecode bits themselves */
+				if (((datahi >> 4) & 0xf) ^ inst_parity(insta)) {
+					printk("   ** bad parity in instruction a\n");
+					res |= CP0_CERRI_DATA_PARITY;
+				}
+				if ((datahi & 0xf) ^ inst_parity(instb)) {
+					printk("   ** bad parity in instruction b\n");
+					res |= CP0_CERRI_DATA_PARITY;
+				}
+				printk("  %05X-%08X%08X", datahi, insta, instb);
+			}
+			printk("\n");
+		}
+	}
+	return res;
+}
+
+/* Compute the ECC for a data doubleword */
+static uint8_t dc_ecc(uint64_t dword)
+{
+	uint64_t t;
+	uint32_t w;
+	uint8_t	 p;
+	int	 i;
+
+	p = 0;
+	for (i = 7; i >= 0; i--)
+	{
+		p <<= 1;
+		t = dword & mask_72_64[i];
+		w = (uint32_t)(t >> 32);
+		p ^= (parity[w>>24] ^ parity[(w>>16) & 0xFF]
+		      ^ parity[(w>>8) & 0xFF] ^ parity[w & 0xFF]);
+		w = (uint32_t)(t & 0xFFFFFFFF);
+		p ^= (parity[w>>24] ^ parity[(w>>16) & 0xFF]
+		      ^ parity[(w>>8) & 0xFF] ^ parity[w & 0xFF]);
+	}
+	return p;
+}
+
+struct dc_state {
+	unsigned char val;
+	char *name;
+};
+
+static struct dc_state dc_states[] = {
+	{ 0x00, "INVALID" },
+	{ 0x0f, "COH-SHD" },
+	{ 0x13, "NCO-E-C" },
+	{ 0x19, "NCO-E-D" },
+	{ 0x16, "COH-E-C" },
+	{ 0x1c, "COH-E-D" },
+	{ 0xff, "*ERROR*" }
+};
+
+#define DC_TAG_VALID(state) \
+    (((state) == 0x0) || ((state) == 0xf) || ((state) == 0x13) || \
+     ((state) == 0x19) || ((state) == 0x16) || ((state) == 0x1c))
+
+static char *dc_state_str(unsigned char state)
+{
+	struct dc_state *dsc = dc_states;
+	while (dsc->val != 0xff) {
+		if (dsc->val == state)
+			break;
+		dsc++;
+	}
+	return dsc->name;
+}
+
+static uint32_t extract_dc(unsigned short addr, int data)
+{
+	int valid, way;
+	unsigned char state;
+	uint32_t taghi, taglolo, taglohi;
+	unsigned long long taglo, pa;
+	uint8_t ecc, lru;
+	int res = 0;
+
+	printk("Dcache index 0x%04x  ", addr);
+	for (way = 0; way < 4; way++) {
+		__asm__ __volatile__ (
+		"	.set	push\n\t"
+		"	.set	noreorder\n\t"
+		"	.set	mips64\n\t"
+		"	.set	noat\n\t"
+		"	cache	5, 0(%3)\n\t"	/* Index-load-tag-D */
+		"	mfc0	%0, $29, 2\n\t"
+		"	dmfc0	$1, $28, 2\n\t"
+		"	dsrl32	%1, $1, 0\n\t"
+		"	sll	%2, $1, 0\n\t"
+		"	.set	pop"
+		: "=r" (taghi), "=r" (taglohi), "=r" (taglolo)
+		: "r" ((way << 13) | addr));
+
+		taglo = ((unsigned long long)taglohi << 32) | taglolo;
+		pa = (taglo & 0xFFFFFFE000ULL) | addr;
+		if (way == 0) {
+			lru = (taghi >> 14) & 0xff;
+			printk("[Bank %d Set 0x%02x]  LRU > %d %d %d %d > MRU\n",
+				    ((addr >> 11) & 0x2) | ((addr >> 5) & 1), /* bank */
+				    ((addr >> 6) & 0x3f), /* index */
+				    (lru & 0x3),
+				    ((lru >> 2) & 0x3),
+				    ((lru >> 4) & 0x3),
+				    ((lru >> 6) & 0x3));
+		}
+		state = (taghi >> 25) & 0x1f;
+		valid = DC_TAG_VALID(state);
+		printk(" %d  [PA %010llx]  [state %s (%02x)]  raw tags: %08X-%016llX\n",
+			    way, pa, dc_state_str(state), state, taghi, taglo);
+		if (valid) {
+			if (((taglo >> 11) & 1) ^ range_parity(taglo, 39, 26)) {
+				printk("   ** bad parity in PTag1\n");
+				res |= CP0_CERRD_TAG_ADDRESS;
+			}
+			if (((taglo >> 10) & 1) ^ range_parity(taglo, 25, 13)) {
+				printk("   ** bad parity in PTag0\n");
+				res |= CP0_CERRD_TAG_ADDRESS;
+			}
+		} else {
+			res |= CP0_CERRD_TAG_STATE;
+		}
+
+		if (data) {
+			uint32_t datalohi, datalolo, datahi;
+			unsigned long long datalo;
+			int offset;
+			char bad_ecc = 0;
+
+			for (offset = 0; offset < 4; offset++) {
+				/* Index-load-data-D */
+				__asm__ __volatile__ (
+				"	.set	push\n\t"
+				"	.set	noreorder\n\t"
+				"	.set	mips64\n\t"
+				"	.set	noat\n\t"
+				"	cache	7, 0(%3)\n\t" /* Index-load-data-D */
+				"	mfc0	%0, $29, 3\n\t"
+				"	dmfc0	$1, $28, 3\n\t"
+				"	dsrl32	%1, $1, 0 \n\t"
+				"	sll	%2, $1, 0 \n\t"
+				"	.set	pop"
+				: "=r" (datahi), "=r" (datalohi), "=r" (datalolo)
+				: "r" ((way << 13) | addr | (offset << 3)));
+				datalo = ((unsigned long long)datalohi << 32) | datalolo;
+				ecc = dc_ecc(datalo);
+				if (ecc != datahi) {
+					int bits;
+					bad_ecc |= 1 << (3-offset);
+					ecc ^= datahi;
+					bits = hweight8(ecc);
+					res |= (bits == 1) ? CP0_CERRD_DATA_SBE : CP0_CERRD_DATA_DBE;
+				}
+				printk("  %02X-%016llX", datahi, datalo);
+			}
+			printk("\n");
+			if (bad_ecc)
+				printk("  dwords w/ bad ECC: %d %d %d %d\n",
+				       !!(bad_ecc & 8), !!(bad_ecc & 4),
+				       !!(bad_ecc & 2), !!(bad_ecc & 1));
+		}
+	}
+	return res;
+}
diff --git a/arch/mips/mm/cex-gen.S b/arch/mips/mm/cex-gen.S
new file mode 100644
index 000000000..45dff5cd4
--- /dev/null
+++ b/arch/mips/mm/cex-gen.S
@@ -0,0 +1,42 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995 - 1999 Ralf Baechle
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ *
+ * Cache error handler
+ */
+#include <asm/asm.h>
+#include <asm/regdef.h>
+#include <asm/mipsregs.h>
+#include <asm/stackframe.h>
+
+/*
+ * Game over.  Go to the button.  Press gently.	 Swear where allowed by
+ * legislation.
+ */
+	LEAF(except_vec2_generic)
+	.set	noreorder
+	.set	noat
+	.set	mips0
+	/*
+	 * This is a very bad place to be.  Our cache error
+	 * detection has triggered.  If we have write-back data
+	 * in the cache, we may not be able to recover.	 As a
+	 * first-order desperate measure, turn off KSEG0 cacheing.
+	 */
+	mfc0	k0,CP0_CONFIG
+	li	k1,~CONF_CM_CMASK
+	and	k0,k0,k1
+	ori	k0,k0,CONF_CM_UNCACHED
+	mtc0	k0,CP0_CONFIG
+	/* Give it a few cycles to sink in... */
+	nop
+	nop
+	nop
+
+	j	cache_parity_error
+	nop
+	END(except_vec2_generic)
diff --git a/arch/mips/mm/cex-oct.S b/arch/mips/mm/cex-oct.S
new file mode 100644
index 000000000..9029092aa
--- /dev/null
+++ b/arch/mips/mm/cex-oct.S
@@ -0,0 +1,70 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2006 Cavium Networks
+ * Cache error handler
+ */
+
+#include <asm/asm.h>
+#include <asm/regdef.h>
+#include <asm/mipsregs.h>
+#include <asm/stackframe.h>
+
+/*
+ * Handle cache error. Indicate to the second level handler whether
+ * the exception is recoverable.
+ */
+	LEAF(except_vec2_octeon)
+
+	.set	push
+	.set	mips64r2
+	.set	noreorder
+	.set	noat
+
+
+	/* due to an errata we need to read the COP0 CacheErr (Dcache)
+	 * before any cache/DRAM access	 */
+
+	rdhwr	k0, $0	      /* get core_id */
+	PTR_LA	k1, cache_err_dcache
+	sll	k0, k0, 3
+	PTR_ADDU k1, k0, k1    /* k1 = &cache_err_dcache[core_id] */
+
+	dmfc0	k0, CP0_CACHEERR, 1
+	sd	k0, (k1)
+	dmtc0	$0, CP0_CACHEERR, 1
+
+	/* check whether this is a nested exception */
+	mfc0	k1, CP0_STATUS
+	andi	k1, k1, ST0_EXL
+	beqz	k1, 1f
+	 nop
+	j	cache_parity_error_octeon_non_recoverable
+	 nop
+
+	/* exception is recoverable */
+1:	j	handle_cache_err
+	 nop
+
+	.set	pop
+	END(except_vec2_octeon)
+
+ /* We need to jump to handle_cache_err so that the previous handler
+  * can fit within 0x80 bytes. We also move from 0xFFFFFFFFAXXXXXXX
+  * space (uncached) to the 0xFFFFFFFF8XXXXXXX space (cached).	*/
+	LEAF(handle_cache_err)
+	.set	push
+	.set	noreorder
+	.set	noat
+
+	SAVE_ALL
+	KMODE
+	jal	cache_parity_error_octeon_recoverable
+	nop
+	j	ret_from_exception
+	nop
+
+	.set pop
+	END(handle_cache_err)
diff --git a/arch/mips/mm/cex-sb1.S b/arch/mips/mm/cex-sb1.S
new file mode 100644
index 000000000..85c6e6a40
--- /dev/null
+++ b/arch/mips/mm/cex-sb1.S
@@ -0,0 +1,157 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2001,2002,2003 Broadcom Corporation
+ */
+
+#include <asm/asm.h>
+#include <asm/regdef.h>
+#include <asm/mipsregs.h>
+#include <asm/stackframe.h>
+#include <asm/cacheops.h>
+#include <asm/sibyte/board.h>
+
+#define C0_ERRCTL     $26	      /* CP0: Error info */
+#define C0_CERR_I     $27	      /* CP0: Icache error */
+#define C0_CERR_D     $27,1	      /* CP0: Dcache error */
+
+	/*
+	 * Based on SiByte sample software cache-err/cerr.S
+	 * CVS revision 1.8.  Only the 'unrecoverable' case
+	 * is changed.
+	 */
+
+	.set	mips64
+	.set	noreorder
+	.set	noat
+
+	/*
+	 * sb1_cerr_vec: code to be copied to the Cache Error
+	 * Exception vector.  The code must be pushed out to memory
+	 * (either by copying to Kseg0 and Kseg1 both, or by flushing
+	 * the L1 and L2) since it is fetched as 0xa0000100.
+	 *
+	 * NOTE: Be sure this handler is at most 28 instructions long
+	 * since the final 16 bytes of the exception vector memory
+	 * (0x170-0x17f) are used to preserve k0, k1, and ra.
+	 */
+
+LEAF(except_vec2_sb1)
+	/*
+	 * If this error is recoverable, we need to exit the handler
+	 * without having dirtied any registers.  To do this,
+	 * save/restore k0 and k1 from low memory (Useg is direct
+	 * mapped while ERL=1). Note that we can't save to a
+	 * CPU-specific location without ruining a register in the
+	 * process.  This means we are vulnerable to data corruption
+	 * whenever the handler is reentered by a second CPU.
+	 */
+	sd	k0,0x170($0)
+	sd	k1,0x178($0)
+
+#ifdef CONFIG_SB1_CEX_ALWAYS_FATAL
+	j	handle_vec2_sb1
+	 nop
+#else
+	/*
+	 * M_ERRCTL_RECOVERABLE is bit 31, which makes it easy to tell
+	 * if we can fast-path out of here for a h/w-recovered error.
+	 */
+	mfc0	k1,C0_ERRCTL
+	bgtz	k1,attempt_recovery
+	 sll	k0,k1,1
+
+recovered_dcache:
+	/*
+	 * Unlock CacheErr-D (which in turn unlocks CacheErr-DPA).
+	 * Ought to log the occurrence of this recovered dcache error.
+	 */
+	b	recovered
+	 mtc0	$0,C0_CERR_D
+
+attempt_recovery:
+	/*
+	 * k0 has C0_ERRCTL << 1, which puts 'DC' at bit 31.  Any
+	 * Dcache errors we can recover from will take more extensive
+	 * processing.	For now, they are considered "unrecoverable".
+	 * Note that 'DC' becoming set (outside of ERL mode) will
+	 * cause 'IC' to clear; so if there's an Icache error, we'll
+	 * only find out about it if we recover from this error and
+	 * continue executing.
+	 */
+	bltz	k0,unrecoverable
+	 sll	k0,1
+
+	/*
+	 * k0 has C0_ERRCTL << 2, which puts 'IC' at bit 31.  If an
+	 * Icache error isn't indicated, I'm not sure why we got here.
+	 * Consider that case "unrecoverable" for now.
+	 */
+	bgez	k0,unrecoverable
+
+attempt_icache_recovery:
+	/*
+	 * External icache errors are due to uncorrectable ECC errors
+	 * in the L2 cache or Memory Controller and cannot be
+	 * recovered here.
+	 */
+	 mfc0	k0,C0_CERR_I		/* delay slot */
+	li	k1,1 << 26		/* ICACHE_EXTERNAL */
+	and	k1,k0
+	bnez	k1,unrecoverable
+	 andi	k0,0x1fe0
+
+	/*
+	 * Since the error is internal, the 'IDX' field from
+	 * CacheErr-I is valid and we can just invalidate all blocks
+	 * in that set.
+	 */
+	cache	Index_Invalidate_I,(0<<13)(k0)
+	cache	Index_Invalidate_I,(1<<13)(k0)
+	cache	Index_Invalidate_I,(2<<13)(k0)
+	cache	Index_Invalidate_I,(3<<13)(k0)
+
+	/* Ought to log this recovered icache error */
+
+recovered:
+	/* Restore the saved registers */
+	ld	k0,0x170($0)
+	ld	k1,0x178($0)
+	eret
+
+unrecoverable:
+	/* Unrecoverable Icache or Dcache error; log it and/or fail */
+	j	handle_vec2_sb1
+	 nop
+#endif
+
+END(except_vec2_sb1)
+
+	LEAF(handle_vec2_sb1)
+	mfc0	k0,CP0_CONFIG
+	li	k1,~CONF_CM_CMASK
+	and	k0,k0,k1
+	ori	k0,k0,CONF_CM_UNCACHED
+	mtc0	k0,CP0_CONFIG
+
+	SSNOP
+	SSNOP
+	SSNOP
+	SSNOP
+	bnezl	$0, 1f
+1:
+	mfc0	k0, CP0_STATUS
+	sll	k0, k0, 3			# check CU0 (kernel?)
+	bltz	k0, 2f
+	 nop
+
+	/* Get a valid Kseg0 stack pointer.  Any task's stack pointer
+	 * will do, although if we ever want to resume execution we
+	 * better not have corrupted any state. */
+	get_saved_sp
+	move	sp, k1
+
+2:
+	j	sb1_cache_error
+	 nop
+
+	END(handle_vec2_sb1)
diff --git a/arch/mips/mm/context.c b/arch/mips/mm/context.c
new file mode 100644
index 000000000..966f40066
--- /dev/null
+++ b/arch/mips/mm/context.c
@@ -0,0 +1,290 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/atomic.h>
+#include <linux/mmu_context.h>
+#include <linux/percpu.h>
+#include <linux/spinlock.h>
+
+static DEFINE_RAW_SPINLOCK(cpu_mmid_lock);
+
+static atomic64_t mmid_version;
+static unsigned int num_mmids;
+static unsigned long *mmid_map;
+
+static DEFINE_PER_CPU(u64, reserved_mmids);
+static cpumask_t tlb_flush_pending;
+
+static bool asid_versions_eq(int cpu, u64 a, u64 b)
+{
+	return ((a ^ b) & asid_version_mask(cpu)) == 0;
+}
+
+void get_new_mmu_context(struct mm_struct *mm)
+{
+	unsigned int cpu;
+	u64 asid;
+
+	/*
+	 * This function is specific to ASIDs, and should not be called when
+	 * MMIDs are in use.
+	 */
+	if (WARN_ON(IS_ENABLED(CONFIG_DEBUG_VM) && cpu_has_mmid))
+		return;
+
+	cpu = smp_processor_id();
+	asid = asid_cache(cpu);
+
+	if (!((asid += cpu_asid_inc()) & cpu_asid_mask(&cpu_data[cpu]))) {
+		if (cpu_has_vtag_icache)
+			flush_icache_all();
+		local_flush_tlb_all();	/* start new asid cycle */
+	}
+
+	set_cpu_context(cpu, mm, asid);
+	asid_cache(cpu) = asid;
+}
+EXPORT_SYMBOL_GPL(get_new_mmu_context);
+
+void check_mmu_context(struct mm_struct *mm)
+{
+	unsigned int cpu = smp_processor_id();
+
+	/*
+	 * This function is specific to ASIDs, and should not be called when
+	 * MMIDs are in use.
+	 */
+	if (WARN_ON(IS_ENABLED(CONFIG_DEBUG_VM) && cpu_has_mmid))
+		return;
+
+	/* Check if our ASID is of an older version and thus invalid */
+	if (!asid_versions_eq(cpu, cpu_context(cpu, mm), asid_cache(cpu)))
+		get_new_mmu_context(mm);
+}
+EXPORT_SYMBOL_GPL(check_mmu_context);
+
+static void flush_context(void)
+{
+	u64 mmid;
+	int cpu;
+
+	/* Update the list of reserved MMIDs and the MMID bitmap */
+	bitmap_zero(mmid_map, num_mmids);
+
+	/* Reserve an MMID for kmap/wired entries */
+	__set_bit(MMID_KERNEL_WIRED, mmid_map);
+
+	for_each_possible_cpu(cpu) {
+		mmid = xchg_relaxed(&cpu_data[cpu].asid_cache, 0);
+
+		/*
+		 * If this CPU has already been through a
+		 * rollover, but hasn't run another task in
+		 * the meantime, we must preserve its reserved
+		 * MMID, as this is the only trace we have of
+		 * the process it is still running.
+		 */
+		if (mmid == 0)
+			mmid = per_cpu(reserved_mmids, cpu);
+
+		__set_bit(mmid & cpu_asid_mask(&cpu_data[cpu]), mmid_map);
+		per_cpu(reserved_mmids, cpu) = mmid;
+	}
+
+	/*
+	 * Queue a TLB invalidation for each CPU to perform on next
+	 * context-switch
+	 */
+	cpumask_setall(&tlb_flush_pending);
+}
+
+static bool check_update_reserved_mmid(u64 mmid, u64 newmmid)
+{
+	bool hit;
+	int cpu;
+
+	/*
+	 * Iterate over the set of reserved MMIDs looking for a match.
+	 * If we find one, then we can update our mm to use newmmid
+	 * (i.e. the same MMID in the current generation) but we can't
+	 * exit the loop early, since we need to ensure that all copies
+	 * of the old MMID are updated to reflect the mm. Failure to do
+	 * so could result in us missing the reserved MMID in a future
+	 * generation.
+	 */
+	hit = false;
+	for_each_possible_cpu(cpu) {
+		if (per_cpu(reserved_mmids, cpu) == mmid) {
+			hit = true;
+			per_cpu(reserved_mmids, cpu) = newmmid;
+		}
+	}
+
+	return hit;
+}
+
+static u64 get_new_mmid(struct mm_struct *mm)
+{
+	static u32 cur_idx = MMID_KERNEL_WIRED + 1;
+	u64 mmid, version, mmid_mask;
+
+	mmid = cpu_context(0, mm);
+	version = atomic64_read(&mmid_version);
+	mmid_mask = cpu_asid_mask(&boot_cpu_data);
+
+	if (!asid_versions_eq(0, mmid, 0)) {
+		u64 newmmid = version | (mmid & mmid_mask);
+
+		/*
+		 * If our current MMID was active during a rollover, we
+		 * can continue to use it and this was just a false alarm.
+		 */
+		if (check_update_reserved_mmid(mmid, newmmid)) {
+			mmid = newmmid;
+			goto set_context;
+		}
+
+		/*
+		 * We had a valid MMID in a previous life, so try to re-use
+		 * it if possible.
+		 */
+		if (!__test_and_set_bit(mmid & mmid_mask, mmid_map)) {
+			mmid = newmmid;
+			goto set_context;
+		}
+	}
+
+	/* Allocate a free MMID */
+	mmid = find_next_zero_bit(mmid_map, num_mmids, cur_idx);
+	if (mmid != num_mmids)
+		goto reserve_mmid;
+
+	/* We're out of MMIDs, so increment the global version */
+	version = atomic64_add_return_relaxed(asid_first_version(0),
+					      &mmid_version);
+
+	/* Note currently active MMIDs & mark TLBs as requiring flushes */
+	flush_context();
+
+	/* We have more MMIDs than CPUs, so this will always succeed */
+	mmid = find_first_zero_bit(mmid_map, num_mmids);
+
+reserve_mmid:
+	__set_bit(mmid, mmid_map);
+	cur_idx = mmid;
+	mmid |= version;
+set_context:
+	set_cpu_context(0, mm, mmid);
+	return mmid;
+}
+
+void check_switch_mmu_context(struct mm_struct *mm)
+{
+	unsigned int cpu = smp_processor_id();
+	u64 ctx, old_active_mmid;
+	unsigned long flags;
+
+	if (!cpu_has_mmid) {
+		check_mmu_context(mm);
+		write_c0_entryhi(cpu_asid(cpu, mm));
+		goto setup_pgd;
+	}
+
+	/*
+	 * MMID switch fast-path, to avoid acquiring cpu_mmid_lock when it's
+	 * unnecessary.
+	 *
+	 * The memory ordering here is subtle. If our active_mmids is non-zero
+	 * and the MMID matches the current version, then we update the CPU's
+	 * asid_cache with a relaxed cmpxchg. Racing with a concurrent rollover
+	 * means that either:
+	 *
+	 * - We get a zero back from the cmpxchg and end up waiting on
+	 *   cpu_mmid_lock in check_mmu_context(). Taking the lock synchronises
+	 *   with the rollover and so we are forced to see the updated
+	 *   generation.
+	 *
+	 * - We get a valid MMID back from the cmpxchg, which means the
+	 *   relaxed xchg in flush_context will treat us as reserved
+	 *   because atomic RmWs are totally ordered for a given location.
+	 */
+	ctx = cpu_context(cpu, mm);
+	old_active_mmid = READ_ONCE(cpu_data[cpu].asid_cache);
+	if (!old_active_mmid ||
+	    !asid_versions_eq(cpu, ctx, atomic64_read(&mmid_version)) ||
+	    !cmpxchg_relaxed(&cpu_data[cpu].asid_cache, old_active_mmid, ctx)) {
+		raw_spin_lock_irqsave(&cpu_mmid_lock, flags);
+
+		ctx = cpu_context(cpu, mm);
+		if (!asid_versions_eq(cpu, ctx, atomic64_read(&mmid_version)))
+			ctx = get_new_mmid(mm);
+
+		WRITE_ONCE(cpu_data[cpu].asid_cache, ctx);
+		raw_spin_unlock_irqrestore(&cpu_mmid_lock, flags);
+	}
+
+	/*
+	 * Invalidate the local TLB if needed. Note that we must only clear our
+	 * bit in tlb_flush_pending after this is complete, so that the
+	 * cpu_has_shared_ftlb_entries case below isn't misled.
+	 */
+	if (cpumask_test_cpu(cpu, &tlb_flush_pending)) {
+		if (cpu_has_vtag_icache)
+			flush_icache_all();
+		local_flush_tlb_all();
+		cpumask_clear_cpu(cpu, &tlb_flush_pending);
+	}
+
+	write_c0_memorymapid(ctx & cpu_asid_mask(&boot_cpu_data));
+
+	/*
+	 * If this CPU shares FTLB entries with its siblings and one or more of
+	 * those siblings hasn't yet invalidated its TLB following a version
+	 * increase then we need to invalidate any TLB entries for our MMID
+	 * that we might otherwise pick up from a sibling.
+	 *
+	 * We ifdef on CONFIG_SMP because cpu_sibling_map isn't defined in
+	 * CONFIG_SMP=n kernels.
+	 */
+#ifdef CONFIG_SMP
+	if (cpu_has_shared_ftlb_entries &&
+	    cpumask_intersects(&tlb_flush_pending, &cpu_sibling_map[cpu])) {
+		/* Ensure we operate on the new MMID */
+		mtc0_tlbw_hazard();
+
+		/*
+		 * Invalidate all TLB entries associated with the new
+		 * MMID, and wait for the invalidation to complete.
+		 */
+		ginvt_mmid();
+		sync_ginv();
+	}
+#endif
+
+setup_pgd:
+	TLBMISS_HANDLER_SETUP_PGD(mm->pgd);
+}
+EXPORT_SYMBOL_GPL(check_switch_mmu_context);
+
+static int mmid_init(void)
+{
+	if (!cpu_has_mmid)
+		return 0;
+
+	/*
+	 * Expect allocation after rollover to fail if we don't have at least
+	 * one more MMID than CPUs.
+	 */
+	num_mmids = asid_first_version(0);
+	WARN_ON(num_mmids <= num_possible_cpus());
+
+	atomic64_set(&mmid_version, asid_first_version(0));
+	mmid_map = bitmap_zalloc(num_mmids, GFP_KERNEL);
+	if (!mmid_map)
+		panic("Failed to allocate bitmap for %u MMIDs\n", num_mmids);
+
+	/* Reserve an MMID for kmap/wired entries */
+	__set_bit(MMID_KERNEL_WIRED, mmid_map);
+
+	pr_info("MMID allocator initialised with %u entries\n", num_mmids);
+	return 0;
+}
+early_initcall(mmid_init);
diff --git a/arch/mips/mm/dma-noncoherent.c b/arch/mips/mm/dma-noncoherent.c
new file mode 100644
index 000000000..3c4fc97b9
--- /dev/null
+++ b/arch/mips/mm/dma-noncoherent.c
@@ -0,0 +1,145 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2000  Ani Joshi <ajoshi@unixbox.com>
+ * Copyright (C) 2000, 2001, 06	 Ralf Baechle <ralf@linux-mips.org>
+ * swiped from i386, and cloned for MIPS by Geert, polished by Ralf.
+ */
+#include <linux/dma-direct.h>
+#include <linux/dma-map-ops.h>
+#include <linux/highmem.h>
+
+#include <asm/cache.h>
+#include <asm/cpu-type.h>
+#include <asm/io.h>
+
+/*
+ * The affected CPUs below in 'cpu_needs_post_dma_flush()' can speculatively
+ * fill random cachelines with stale data at any time, requiring an extra
+ * flush post-DMA.
+ *
+ * Warning on the terminology - Linux calls an uncached area coherent;  MIPS
+ * terminology calls memory areas with hardware maintained coherency coherent.
+ *
+ * Note that the R14000 and R16000 should also be checked for in this condition.
+ * However this function is only called on non-I/O-coherent systems and only the
+ * R10000 and R12000 are used in such systems, the SGI IP28 Indigo² rsp.
+ * SGI IP32 aka O2.
+ */
+static inline bool cpu_needs_post_dma_flush(void)
+{
+	switch (boot_cpu_type()) {
+	case CPU_R10000:
+	case CPU_R12000:
+	case CPU_BMIPS5000:
+	case CPU_LOONGSON2EF:
+	case CPU_XBURST:
+		return true;
+	default:
+		/*
+		 * Presence of MAARs suggests that the CPU supports
+		 * speculatively prefetching data, and therefore requires
+		 * the post-DMA flush/invalidate.
+		 */
+		return cpu_has_maar;
+	}
+}
+
+void arch_dma_prep_coherent(struct page *page, size_t size)
+{
+	dma_cache_wback_inv((unsigned long)page_address(page), size);
+}
+
+void *arch_dma_set_uncached(void *addr, size_t size)
+{
+	return (void *)(__pa(addr) + UNCAC_BASE);
+}
+
+static inline void dma_sync_virt_for_device(void *addr, size_t size,
+		enum dma_data_direction dir)
+{
+	switch (dir) {
+	case DMA_TO_DEVICE:
+		dma_cache_wback((unsigned long)addr, size);
+		break;
+	case DMA_FROM_DEVICE:
+		dma_cache_inv((unsigned long)addr, size);
+		break;
+	case DMA_BIDIRECTIONAL:
+		dma_cache_wback_inv((unsigned long)addr, size);
+		break;
+	default:
+		BUG();
+	}
+}
+
+static inline void dma_sync_virt_for_cpu(void *addr, size_t size,
+		enum dma_data_direction dir)
+{
+	switch (dir) {
+	case DMA_TO_DEVICE:
+		break;
+	case DMA_FROM_DEVICE:
+	case DMA_BIDIRECTIONAL:
+		dma_cache_inv((unsigned long)addr, size);
+		break;
+	default:
+		BUG();
+	}
+}
+
+/*
+ * A single sg entry may refer to multiple physically contiguous pages.  But
+ * we still need to process highmem pages individually.  If highmem is not
+ * configured then the bulk of this loop gets optimized out.
+ */
+static inline void dma_sync_phys(phys_addr_t paddr, size_t size,
+		enum dma_data_direction dir, bool for_device)
+{
+	struct page *page = pfn_to_page(paddr >> PAGE_SHIFT);
+	unsigned long offset = paddr & ~PAGE_MASK;
+	size_t left = size;
+
+	do {
+		size_t len = left;
+		void *addr;
+
+		if (PageHighMem(page)) {
+			if (offset + len > PAGE_SIZE)
+				len = PAGE_SIZE - offset;
+		}
+
+		addr = kmap_atomic(page);
+		if (for_device)
+			dma_sync_virt_for_device(addr + offset, len, dir);
+		else
+			dma_sync_virt_for_cpu(addr + offset, len, dir);
+		kunmap_atomic(addr);
+
+		offset = 0;
+		page++;
+		left -= len;
+	} while (left);
+}
+
+void arch_sync_dma_for_device(phys_addr_t paddr, size_t size,
+		enum dma_data_direction dir)
+{
+	dma_sync_phys(paddr, size, dir, true);
+}
+
+#ifdef CONFIG_ARCH_HAS_SYNC_DMA_FOR_CPU
+void arch_sync_dma_for_cpu(phys_addr_t paddr, size_t size,
+		enum dma_data_direction dir)
+{
+	if (cpu_needs_post_dma_flush())
+		dma_sync_phys(paddr, size, dir, false);
+}
+#endif
+
+#ifdef CONFIG_ARCH_HAS_SETUP_DMA_OPS
+void arch_setup_dma_ops(struct device *dev, u64 dma_base, u64 size,
+		const struct iommu_ops *iommu, bool coherent)
+{
+	dev->dma_coherent = coherent;
+}
+#endif
diff --git a/arch/mips/mm/extable.c b/arch/mips/mm/extable.c
new file mode 100644
index 000000000..81bc8a34a
--- /dev/null
+++ b/arch/mips/mm/extable.c
@@ -0,0 +1,25 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1997, 99, 2001 - 2004 Ralf Baechle <ralf@linux-mips.org>
+ */
+#include <linux/extable.h>
+#include <linux/spinlock.h>
+#include <asm/branch.h>
+#include <linux/uaccess.h>
+
+int fixup_exception(struct pt_regs *regs)
+{
+	const struct exception_table_entry *fixup;
+
+	fixup = search_exception_tables(exception_epc(regs));
+	if (fixup) {
+		regs->cp0_epc = fixup->nextinsn;
+
+		return 1;
+	}
+
+	return 0;
+}
diff --git a/arch/mips/mm/fault.c b/arch/mips/mm/fault.c
new file mode 100644
index 000000000..d7878208b
--- /dev/null
+++ b/arch/mips/mm/fault.c
@@ -0,0 +1,332 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995 - 2000 by Ralf Baechle
+ */
+#include <linux/context_tracking.h>
+#include <linux/signal.h>
+#include <linux/sched.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/string.h>
+#include <linux/types.h>
+#include <linux/ptrace.h>
+#include <linux/ratelimit.h>
+#include <linux/mman.h>
+#include <linux/mm.h>
+#include <linux/smp.h>
+#include <linux/kprobes.h>
+#include <linux/perf_event.h>
+#include <linux/uaccess.h>
+
+#include <asm/branch.h>
+#include <asm/mmu_context.h>
+#include <asm/ptrace.h>
+#include <asm/highmem.h>		/* For VMALLOC_END */
+#include <linux/kdebug.h>
+
+int show_unhandled_signals = 1;
+
+/*
+ * This routine handles page faults.  It determines the address,
+ * and the problem, and then passes it off to one of the appropriate
+ * routines.
+ */
+static void __do_page_fault(struct pt_regs *regs, unsigned long write,
+	unsigned long address)
+{
+	struct vm_area_struct * vma = NULL;
+	struct task_struct *tsk = current;
+	struct mm_struct *mm = tsk->mm;
+	const int field = sizeof(unsigned long) * 2;
+	int si_code;
+	vm_fault_t fault;
+	unsigned int flags = FAULT_FLAG_DEFAULT;
+
+	static DEFINE_RATELIMIT_STATE(ratelimit_state, 5 * HZ, 10);
+
+#if 0
+	printk("Cpu%d[%s:%d:%0*lx:%ld:%0*lx]\n", raw_smp_processor_id(),
+	       current->comm, current->pid, field, address, write,
+	       field, regs->cp0_epc);
+#endif
+
+#ifdef CONFIG_KPROBES
+	/*
+	 * This is to notify the fault handler of the kprobes.
+	 */
+	if (notify_die(DIE_PAGE_FAULT, "page fault", regs, -1,
+		       current->thread.trap_nr, SIGSEGV) == NOTIFY_STOP)
+		return;
+#endif
+
+	si_code = SEGV_MAPERR;
+
+	/*
+	 * We fault-in kernel-space virtual memory on-demand. The
+	 * 'reference' page table is init_mm.pgd.
+	 *
+	 * NOTE! We MUST NOT take any locks for this case. We may
+	 * be in an interrupt or a critical region, and should
+	 * only copy the information from the master page table,
+	 * nothing more.
+	 */
+#ifdef CONFIG_64BIT
+# define VMALLOC_FAULT_TARGET no_context
+#else
+# define VMALLOC_FAULT_TARGET vmalloc_fault
+#endif
+
+	if (unlikely(address >= VMALLOC_START && address <= VMALLOC_END))
+		goto VMALLOC_FAULT_TARGET;
+#ifdef MODULE_START
+	if (unlikely(address >= MODULE_START && address < MODULE_END))
+		goto VMALLOC_FAULT_TARGET;
+#endif
+
+	/*
+	 * If we're in an interrupt or have no user
+	 * context, we must not take the fault..
+	 */
+	if (faulthandler_disabled() || !mm)
+		goto bad_area_nosemaphore;
+
+	if (user_mode(regs))
+		flags |= FAULT_FLAG_USER;
+
+	perf_sw_event(PERF_COUNT_SW_PAGE_FAULTS, 1, regs, address);
+retry:
+	vma = lock_mm_and_find_vma(mm, address, regs);
+	if (!vma)
+		goto bad_area_nosemaphore;
+/*
+ * Ok, we have a good vm_area for this memory access, so
+ * we can handle it..
+ */
+	si_code = SEGV_ACCERR;
+
+	if (write) {
+		if (!(vma->vm_flags & VM_WRITE))
+			goto bad_area;
+		flags |= FAULT_FLAG_WRITE;
+	} else {
+		if (cpu_has_rixi) {
+			if (address == regs->cp0_epc && !(vma->vm_flags & VM_EXEC)) {
+#if 0
+				pr_notice("Cpu%d[%s:%d:%0*lx:%ld:%0*lx] XI violation\n",
+					  raw_smp_processor_id(),
+					  current->comm, current->pid,
+					  field, address, write,
+					  field, regs->cp0_epc);
+#endif
+				goto bad_area;
+			}
+			if (!(vma->vm_flags & VM_READ) &&
+			    exception_epc(regs) != address) {
+#if 0
+				pr_notice("Cpu%d[%s:%d:%0*lx:%ld:%0*lx] RI violation\n",
+					  raw_smp_processor_id(),
+					  current->comm, current->pid,
+					  field, address, write,
+					  field, regs->cp0_epc);
+#endif
+				goto bad_area;
+			}
+		} else {
+			if (unlikely(!vma_is_accessible(vma)))
+				goto bad_area;
+		}
+	}
+
+	/*
+	 * If for any reason at all we couldn't handle the fault,
+	 * make sure we exit gracefully rather than endlessly redo
+	 * the fault.
+	 */
+	fault = handle_mm_fault(vma, address, flags, regs);
+
+	if (fault_signal_pending(fault, regs)) {
+		if (!user_mode(regs))
+			goto no_context;
+		return;
+	}
+
+	/* The fault is fully completed (including releasing mmap lock) */
+	if (fault & VM_FAULT_COMPLETED)
+		return;
+
+	if (unlikely(fault & VM_FAULT_ERROR)) {
+		if (fault & VM_FAULT_OOM)
+			goto out_of_memory;
+		else if (fault & VM_FAULT_SIGSEGV)
+			goto bad_area;
+		else if (fault & VM_FAULT_SIGBUS)
+			goto do_sigbus;
+		BUG();
+	}
+
+	if (fault & VM_FAULT_RETRY) {
+		flags |= FAULT_FLAG_TRIED;
+
+		/*
+		 * No need to mmap_read_unlock(mm) as we would
+		 * have already released it in __lock_page_or_retry
+		 * in mm/filemap.c.
+		 */
+
+		goto retry;
+	}
+
+	mmap_read_unlock(mm);
+	return;
+
+/*
+ * Something tried to access memory that isn't in our memory map..
+ * Fix it, but check if it's kernel or user first..
+ */
+bad_area:
+	mmap_read_unlock(mm);
+
+bad_area_nosemaphore:
+	/* User mode accesses just cause a SIGSEGV */
+	if (user_mode(regs)) {
+		tsk->thread.cp0_badvaddr = address;
+		tsk->thread.error_code = write;
+		if (show_unhandled_signals &&
+		    unhandled_signal(tsk, SIGSEGV) &&
+		    __ratelimit(&ratelimit_state)) {
+			pr_info("do_page_fault(): sending SIGSEGV to %s for invalid %s %0*lx\n",
+				tsk->comm,
+				write ? "write access to" : "read access from",
+				field, address);
+			pr_info("epc = %0*lx in", field,
+				(unsigned long) regs->cp0_epc);
+			print_vma_addr(KERN_CONT " ", regs->cp0_epc);
+			pr_cont("\n");
+			pr_info("ra  = %0*lx in", field,
+				(unsigned long) regs->regs[31]);
+			print_vma_addr(KERN_CONT " ", regs->regs[31]);
+			pr_cont("\n");
+		}
+		current->thread.trap_nr = (regs->cp0_cause >> 2) & 0x1f;
+		force_sig_fault(SIGSEGV, si_code, (void __user *)address);
+		return;
+	}
+
+no_context:
+	/* Are we prepared to handle this kernel fault?	 */
+	if (fixup_exception(regs)) {
+		current->thread.cp0_baduaddr = address;
+		return;
+	}
+
+	/*
+	 * Oops. The kernel tried to access some bad page. We'll have to
+	 * terminate things with extreme prejudice.
+	 */
+	bust_spinlocks(1);
+
+	printk(KERN_ALERT "CPU %d Unable to handle kernel paging request at "
+	       "virtual address %0*lx, epc == %0*lx, ra == %0*lx\n",
+	       raw_smp_processor_id(), field, address, field, regs->cp0_epc,
+	       field,  regs->regs[31]);
+	die("Oops", regs);
+
+out_of_memory:
+	/*
+	 * We ran out of memory, call the OOM killer, and return the userspace
+	 * (which will retry the fault, or kill us if we got oom-killed).
+	 */
+	mmap_read_unlock(mm);
+	if (!user_mode(regs))
+		goto no_context;
+	pagefault_out_of_memory();
+	return;
+
+do_sigbus:
+	mmap_read_unlock(mm);
+
+	/* Kernel mode? Handle exceptions or die */
+	if (!user_mode(regs))
+		goto no_context;
+
+	/*
+	 * Send a sigbus, regardless of whether we were in kernel
+	 * or user mode.
+	 */
+#if 0
+	printk("do_page_fault() #3: sending SIGBUS to %s for "
+	       "invalid %s\n%0*lx (epc == %0*lx, ra == %0*lx)\n",
+	       tsk->comm,
+	       write ? "write access to" : "read access from",
+	       field, address,
+	       field, (unsigned long) regs->cp0_epc,
+	       field, (unsigned long) regs->regs[31]);
+#endif
+	current->thread.trap_nr = (regs->cp0_cause >> 2) & 0x1f;
+	tsk->thread.cp0_badvaddr = address;
+	force_sig_fault(SIGBUS, BUS_ADRERR, (void __user *)address);
+
+	return;
+#ifndef CONFIG_64BIT
+vmalloc_fault:
+	{
+		/*
+		 * Synchronize this task's top level page-table
+		 * with the 'reference' page table.
+		 *
+		 * Do _not_ use "tsk" here. We might be inside
+		 * an interrupt in the middle of a task switch..
+		 */
+		int offset = pgd_index(address);
+		pgd_t *pgd, *pgd_k;
+		p4d_t *p4d, *p4d_k;
+		pud_t *pud, *pud_k;
+		pmd_t *pmd, *pmd_k;
+		pte_t *pte_k;
+
+		pgd = (pgd_t *) pgd_current[raw_smp_processor_id()] + offset;
+		pgd_k = init_mm.pgd + offset;
+
+		if (!pgd_present(*pgd_k))
+			goto no_context;
+		set_pgd(pgd, *pgd_k);
+
+		p4d = p4d_offset(pgd, address);
+		p4d_k = p4d_offset(pgd_k, address);
+		if (!p4d_present(*p4d_k))
+			goto no_context;
+
+		pud = pud_offset(p4d, address);
+		pud_k = pud_offset(p4d_k, address);
+		if (!pud_present(*pud_k))
+			goto no_context;
+
+		pmd = pmd_offset(pud, address);
+		pmd_k = pmd_offset(pud_k, address);
+		if (!pmd_present(*pmd_k))
+			goto no_context;
+		set_pmd(pmd, *pmd_k);
+
+		pte_k = pte_offset_kernel(pmd_k, address);
+		if (!pte_present(*pte_k))
+			goto no_context;
+		return;
+	}
+#endif
+}
+NOKPROBE_SYMBOL(__do_page_fault);
+
+asmlinkage void do_page_fault(struct pt_regs *regs,
+	unsigned long write, unsigned long address)
+{
+	enum ctx_state prev_state;
+
+	prev_state = exception_enter();
+	__do_page_fault(regs, write, address);
+	exception_exit(prev_state);
+}
+NOKPROBE_SYMBOL(do_page_fault);
diff --git a/arch/mips/mm/highmem.c b/arch/mips/mm/highmem.c
new file mode 100644
index 000000000..57e2f08f0
--- /dev/null
+++ b/arch/mips/mm/highmem.c
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/compiler.h>
+#include <linux/init.h>
+#include <linux/export.h>
+#include <linux/highmem.h>
+#include <linux/sched.h>
+#include <linux/smp.h>
+#include <asm/fixmap.h>
+#include <asm/tlbflush.h>
+
+unsigned long highstart_pfn, highend_pfn;
+
+void kmap_flush_tlb(unsigned long addr)
+{
+	flush_tlb_one(addr);
+}
+EXPORT_SYMBOL(kmap_flush_tlb);
diff --git a/arch/mips/mm/hugetlbpage.c b/arch/mips/mm/hugetlbpage.c
new file mode 100644
index 000000000..7eaff5b07
--- /dev/null
+++ b/arch/mips/mm/hugetlbpage.c
@@ -0,0 +1,69 @@
+/*
+ * MIPS Huge TLB Page Support for Kernel.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2002, Rohit Seth <rohit.seth@intel.com>
+ * Copyright 2005, Embedded Alley Solutions, Inc.
+ * Matt Porter <mporter@embeddedalley.com>
+ * Copyright (C) 2008, 2009 Cavium Networks, Inc.
+ */
+
+#include <linux/fs.h>
+#include <linux/mm.h>
+#include <linux/hugetlb.h>
+#include <linux/pagemap.h>
+#include <linux/err.h>
+#include <linux/sysctl.h>
+#include <asm/mman.h>
+#include <asm/tlb.h>
+#include <asm/tlbflush.h>
+
+pte_t *huge_pte_alloc(struct mm_struct *mm, struct vm_area_struct *vma,
+		      unsigned long addr, unsigned long sz)
+{
+	pgd_t *pgd;
+	p4d_t *p4d;
+	pud_t *pud;
+	pte_t *pte = NULL;
+
+	pgd = pgd_offset(mm, addr);
+	p4d = p4d_alloc(mm, pgd, addr);
+	pud = pud_alloc(mm, p4d, addr);
+	if (pud)
+		pte = (pte_t *)pmd_alloc(mm, pud, addr);
+
+	return pte;
+}
+
+pte_t *huge_pte_offset(struct mm_struct *mm, unsigned long addr,
+		       unsigned long sz)
+{
+	pgd_t *pgd;
+	p4d_t *p4d;
+	pud_t *pud;
+	pmd_t *pmd = NULL;
+
+	pgd = pgd_offset(mm, addr);
+	if (pgd_present(*pgd)) {
+		p4d = p4d_offset(pgd, addr);
+		if (p4d_present(*p4d)) {
+			pud = pud_offset(p4d, addr);
+			if (pud_present(*pud))
+				pmd = pmd_offset(pud, addr);
+		}
+	}
+	return (pte_t *) pmd;
+}
+
+int pmd_huge(pmd_t pmd)
+{
+	return (pmd_val(pmd) & _PAGE_HUGE) != 0;
+}
+
+int pud_huge(pud_t pud)
+{
+	return (pud_val(pud) & _PAGE_HUGE) != 0;
+}
diff --git a/arch/mips/mm/init.c b/arch/mips/mm/init.c
new file mode 100644
index 000000000..e8660d06f
--- /dev/null
+++ b/arch/mips/mm/init.c
@@ -0,0 +1,568 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994 - 2000 Ralf Baechle
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ * Kevin D. Kissell, kevink@mips.com and Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 2000 MIPS Technologies, Inc.  All rights reserved.
+ */
+#include <linux/bug.h>
+#include <linux/init.h>
+#include <linux/export.h>
+#include <linux/signal.h>
+#include <linux/sched.h>
+#include <linux/smp.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/string.h>
+#include <linux/types.h>
+#include <linux/pagemap.h>
+#include <linux/ptrace.h>
+#include <linux/mman.h>
+#include <linux/mm.h>
+#include <linux/memblock.h>
+#include <linux/highmem.h>
+#include <linux/swap.h>
+#include <linux/proc_fs.h>
+#include <linux/pfn.h>
+#include <linux/hardirq.h>
+#include <linux/gfp.h>
+#include <linux/kcore.h>
+#include <linux/initrd.h>
+
+#include <asm/bootinfo.h>
+#include <asm/cachectl.h>
+#include <asm/cpu.h>
+#include <asm/dma.h>
+#include <asm/maar.h>
+#include <asm/mmu_context.h>
+#include <asm/sections.h>
+#include <asm/pgalloc.h>
+#include <asm/tlb.h>
+#include <asm/fixmap.h>
+
+/*
+ * We have up to 8 empty zeroed pages so we can map one of the right colour
+ * when needed.	 This is necessary only on R4000 / R4400 SC and MC versions
+ * where we have to avoid VCED / VECI exceptions for good performance at
+ * any price.  Since page is never written to after the initialization we
+ * don't have to care about aliases on other CPUs.
+ */
+unsigned long empty_zero_page, zero_page_mask;
+EXPORT_SYMBOL_GPL(empty_zero_page);
+EXPORT_SYMBOL(zero_page_mask);
+
+/*
+ * Not static inline because used by IP27 special magic initialization code
+ */
+void setup_zero_pages(void)
+{
+	unsigned int order, i;
+	struct page *page;
+
+	if (cpu_has_vce)
+		order = 3;
+	else
+		order = 0;
+
+	empty_zero_page = __get_free_pages(GFP_KERNEL | __GFP_ZERO, order);
+	if (!empty_zero_page)
+		panic("Oh boy, that early out of memory?");
+
+	page = virt_to_page((void *)empty_zero_page);
+	split_page(page, order);
+	for (i = 0; i < (1 << order); i++, page++)
+		mark_page_reserved(page);
+
+	zero_page_mask = ((PAGE_SIZE << order) - 1) & PAGE_MASK;
+}
+
+static void *__kmap_pgprot(struct page *page, unsigned long addr, pgprot_t prot)
+{
+	enum fixed_addresses idx;
+	unsigned int old_mmid;
+	unsigned long vaddr, flags, entrylo;
+	unsigned long old_ctx;
+	pte_t pte;
+	int tlbidx;
+
+	BUG_ON(Page_dcache_dirty(page));
+
+	preempt_disable();
+	pagefault_disable();
+	idx = (addr >> PAGE_SHIFT) & (FIX_N_COLOURS - 1);
+	idx += in_interrupt() ? FIX_N_COLOURS : 0;
+	vaddr = __fix_to_virt(FIX_CMAP_END - idx);
+	pte = mk_pte(page, prot);
+#if defined(CONFIG_XPA)
+	entrylo = pte_to_entrylo(pte.pte_high);
+#elif defined(CONFIG_PHYS_ADDR_T_64BIT) && defined(CONFIG_CPU_MIPS32)
+	entrylo = pte.pte_high;
+#else
+	entrylo = pte_to_entrylo(pte_val(pte));
+#endif
+
+	local_irq_save(flags);
+	old_ctx = read_c0_entryhi();
+	write_c0_entryhi(vaddr & (PAGE_MASK << 1));
+	write_c0_entrylo0(entrylo);
+	write_c0_entrylo1(entrylo);
+	if (cpu_has_mmid) {
+		old_mmid = read_c0_memorymapid();
+		write_c0_memorymapid(MMID_KERNEL_WIRED);
+	}
+#ifdef CONFIG_XPA
+	if (cpu_has_xpa) {
+		entrylo = (pte.pte_low & _PFNX_MASK);
+		writex_c0_entrylo0(entrylo);
+		writex_c0_entrylo1(entrylo);
+	}
+#endif
+	tlbidx = num_wired_entries();
+	write_c0_wired(tlbidx + 1);
+	write_c0_index(tlbidx);
+	mtc0_tlbw_hazard();
+	tlb_write_indexed();
+	tlbw_use_hazard();
+	write_c0_entryhi(old_ctx);
+	if (cpu_has_mmid)
+		write_c0_memorymapid(old_mmid);
+	local_irq_restore(flags);
+
+	return (void*) vaddr;
+}
+
+void *kmap_coherent(struct page *page, unsigned long addr)
+{
+	return __kmap_pgprot(page, addr, PAGE_KERNEL);
+}
+
+void *kmap_noncoherent(struct page *page, unsigned long addr)
+{
+	return __kmap_pgprot(page, addr, PAGE_KERNEL_NC);
+}
+
+void kunmap_coherent(void)
+{
+	unsigned int wired;
+	unsigned long flags, old_ctx;
+
+	local_irq_save(flags);
+	old_ctx = read_c0_entryhi();
+	wired = num_wired_entries() - 1;
+	write_c0_wired(wired);
+	write_c0_index(wired);
+	write_c0_entryhi(UNIQUE_ENTRYHI(wired));
+	write_c0_entrylo0(0);
+	write_c0_entrylo1(0);
+	mtc0_tlbw_hazard();
+	tlb_write_indexed();
+	tlbw_use_hazard();
+	write_c0_entryhi(old_ctx);
+	local_irq_restore(flags);
+	pagefault_enable();
+	preempt_enable();
+}
+
+void copy_user_highpage(struct page *to, struct page *from,
+	unsigned long vaddr, struct vm_area_struct *vma)
+{
+	void *vfrom, *vto;
+
+	vto = kmap_atomic(to);
+	if (cpu_has_dc_aliases &&
+	    page_mapcount(from) && !Page_dcache_dirty(from)) {
+		vfrom = kmap_coherent(from, vaddr);
+		copy_page(vto, vfrom);
+		kunmap_coherent();
+	} else {
+		vfrom = kmap_atomic(from);
+		copy_page(vto, vfrom);
+		kunmap_atomic(vfrom);
+	}
+	if ((!cpu_has_ic_fills_f_dc) ||
+	    pages_do_alias((unsigned long)vto, vaddr & PAGE_MASK))
+		flush_data_cache_page((unsigned long)vto);
+	kunmap_atomic(vto);
+	/* Make sure this page is cleared on other CPU's too before using it */
+	smp_wmb();
+}
+
+void copy_to_user_page(struct vm_area_struct *vma,
+	struct page *page, unsigned long vaddr, void *dst, const void *src,
+	unsigned long len)
+{
+	if (cpu_has_dc_aliases &&
+	    page_mapcount(page) && !Page_dcache_dirty(page)) {
+		void *vto = kmap_coherent(page, vaddr) + (vaddr & ~PAGE_MASK);
+		memcpy(vto, src, len);
+		kunmap_coherent();
+	} else {
+		memcpy(dst, src, len);
+		if (cpu_has_dc_aliases)
+			SetPageDcacheDirty(page);
+	}
+	if (vma->vm_flags & VM_EXEC)
+		flush_cache_page(vma, vaddr, page_to_pfn(page));
+}
+
+void copy_from_user_page(struct vm_area_struct *vma,
+	struct page *page, unsigned long vaddr, void *dst, const void *src,
+	unsigned long len)
+{
+	if (cpu_has_dc_aliases &&
+	    page_mapcount(page) && !Page_dcache_dirty(page)) {
+		void *vfrom = kmap_coherent(page, vaddr) + (vaddr & ~PAGE_MASK);
+		memcpy(dst, vfrom, len);
+		kunmap_coherent();
+	} else {
+		memcpy(dst, src, len);
+		if (cpu_has_dc_aliases)
+			SetPageDcacheDirty(page);
+	}
+}
+EXPORT_SYMBOL_GPL(copy_from_user_page);
+
+void __init fixrange_init(unsigned long start, unsigned long end,
+	pgd_t *pgd_base)
+{
+#ifdef CONFIG_HIGHMEM
+	pgd_t *pgd;
+	pud_t *pud;
+	pmd_t *pmd;
+	pte_t *pte;
+	int i, j, k;
+	unsigned long vaddr;
+
+	vaddr = start;
+	i = pgd_index(vaddr);
+	j = pud_index(vaddr);
+	k = pmd_index(vaddr);
+	pgd = pgd_base + i;
+
+	for ( ; (i < PTRS_PER_PGD) && (vaddr < end); pgd++, i++) {
+		pud = (pud_t *)pgd;
+		for ( ; (j < PTRS_PER_PUD) && (vaddr < end); pud++, j++) {
+			pmd = (pmd_t *)pud;
+			for (; (k < PTRS_PER_PMD) && (vaddr < end); pmd++, k++) {
+				if (pmd_none(*pmd)) {
+					pte = (pte_t *) memblock_alloc_low(PAGE_SIZE,
+									   PAGE_SIZE);
+					if (!pte)
+						panic("%s: Failed to allocate %lu bytes align=%lx\n",
+						      __func__, PAGE_SIZE,
+						      PAGE_SIZE);
+
+					set_pmd(pmd, __pmd((unsigned long)pte));
+					BUG_ON(pte != pte_offset_kernel(pmd, 0));
+				}
+				vaddr += PMD_SIZE;
+			}
+			k = 0;
+		}
+		j = 0;
+	}
+#endif
+}
+
+struct maar_walk_info {
+	struct maar_config cfg[16];
+	unsigned int num_cfg;
+};
+
+static int maar_res_walk(unsigned long start_pfn, unsigned long nr_pages,
+			 void *data)
+{
+	struct maar_walk_info *wi = data;
+	struct maar_config *cfg = &wi->cfg[wi->num_cfg];
+	unsigned int maar_align;
+
+	/* MAAR registers hold physical addresses right shifted by 4 bits */
+	maar_align = BIT(MIPS_MAAR_ADDR_SHIFT + 4);
+
+	/* Fill in the MAAR config entry */
+	cfg->lower = ALIGN(PFN_PHYS(start_pfn), maar_align);
+	cfg->upper = ALIGN_DOWN(PFN_PHYS(start_pfn + nr_pages), maar_align) - 1;
+	cfg->attrs = MIPS_MAAR_S;
+
+	/* Ensure we don't overflow the cfg array */
+	if (!WARN_ON(wi->num_cfg >= ARRAY_SIZE(wi->cfg)))
+		wi->num_cfg++;
+
+	return 0;
+}
+
+
+unsigned __weak platform_maar_init(unsigned num_pairs)
+{
+	unsigned int num_configured;
+	struct maar_walk_info wi;
+
+	wi.num_cfg = 0;
+	walk_system_ram_range(0, max_pfn, &wi, maar_res_walk);
+
+	num_configured = maar_config(wi.cfg, wi.num_cfg, num_pairs);
+	if (num_configured < wi.num_cfg)
+		pr_warn("Not enough MAAR pairs (%u) for all memory regions (%u)\n",
+			num_pairs, wi.num_cfg);
+
+	return num_configured;
+}
+
+void maar_init(void)
+{
+	unsigned num_maars, used, i;
+	phys_addr_t lower, upper, attr;
+	static struct {
+		struct maar_config cfgs[3];
+		unsigned used;
+	} recorded = { { { 0 } }, 0 };
+
+	if (!cpu_has_maar)
+		return;
+
+	/* Detect the number of MAARs */
+	write_c0_maari(~0);
+	back_to_back_c0_hazard();
+	num_maars = read_c0_maari() + 1;
+
+	/* MAARs should be in pairs */
+	WARN_ON(num_maars % 2);
+
+	/* Set MAARs using values we recorded already */
+	if (recorded.used) {
+		used = maar_config(recorded.cfgs, recorded.used, num_maars / 2);
+		BUG_ON(used != recorded.used);
+	} else {
+		/* Configure the required MAARs */
+		used = platform_maar_init(num_maars / 2);
+	}
+
+	/* Disable any further MAARs */
+	for (i = (used * 2); i < num_maars; i++) {
+		write_c0_maari(i);
+		back_to_back_c0_hazard();
+		write_c0_maar(0);
+		back_to_back_c0_hazard();
+	}
+
+	if (recorded.used)
+		return;
+
+	pr_info("MAAR configuration:\n");
+	for (i = 0; i < num_maars; i += 2) {
+		write_c0_maari(i);
+		back_to_back_c0_hazard();
+		upper = read_c0_maar();
+#ifdef CONFIG_XPA
+		upper |= (phys_addr_t)readx_c0_maar() << MIPS_MAARX_ADDR_SHIFT;
+#endif
+
+		write_c0_maari(i + 1);
+		back_to_back_c0_hazard();
+		lower = read_c0_maar();
+#ifdef CONFIG_XPA
+		lower |= (phys_addr_t)readx_c0_maar() << MIPS_MAARX_ADDR_SHIFT;
+#endif
+
+		attr = lower & upper;
+		lower = (lower & MIPS_MAAR_ADDR) << 4;
+		upper = ((upper & MIPS_MAAR_ADDR) << 4) | 0xffff;
+
+		pr_info("  [%d]: ", i / 2);
+		if ((attr & MIPS_MAAR_V) != MIPS_MAAR_V) {
+			pr_cont("disabled\n");
+			continue;
+		}
+
+		pr_cont("%pa-%pa", &lower, &upper);
+
+		if (attr & MIPS_MAAR_S)
+			pr_cont(" speculate");
+
+		pr_cont("\n");
+
+		/* Record the setup for use on secondary CPUs */
+		if (used <= ARRAY_SIZE(recorded.cfgs)) {
+			recorded.cfgs[recorded.used].lower = lower;
+			recorded.cfgs[recorded.used].upper = upper;
+			recorded.cfgs[recorded.used].attrs = attr;
+			recorded.used++;
+		}
+	}
+}
+
+#ifndef CONFIG_NUMA
+void __init paging_init(void)
+{
+	unsigned long max_zone_pfns[MAX_NR_ZONES];
+
+	pagetable_init();
+
+#ifdef CONFIG_ZONE_DMA
+	max_zone_pfns[ZONE_DMA] = MAX_DMA_PFN;
+#endif
+#ifdef CONFIG_ZONE_DMA32
+	max_zone_pfns[ZONE_DMA32] = MAX_DMA32_PFN;
+#endif
+	max_zone_pfns[ZONE_NORMAL] = max_low_pfn;
+#ifdef CONFIG_HIGHMEM
+	max_zone_pfns[ZONE_HIGHMEM] = highend_pfn;
+
+	if (cpu_has_dc_aliases && max_low_pfn != highend_pfn) {
+		printk(KERN_WARNING "This processor doesn't support highmem."
+		       " %ldk highmem ignored\n",
+		       (highend_pfn - max_low_pfn) << (PAGE_SHIFT - 10));
+		max_zone_pfns[ZONE_HIGHMEM] = max_low_pfn;
+	}
+
+	max_mapnr = highend_pfn ? highend_pfn : max_low_pfn;
+#else
+	max_mapnr = max_low_pfn;
+#endif
+	high_memory = (void *) __va(max_low_pfn << PAGE_SHIFT);
+
+	free_area_init(max_zone_pfns);
+}
+
+#ifdef CONFIG_64BIT
+static struct kcore_list kcore_kseg0;
+#endif
+
+static inline void __init mem_init_free_highmem(void)
+{
+#ifdef CONFIG_HIGHMEM
+	unsigned long tmp;
+
+	if (cpu_has_dc_aliases)
+		return;
+
+	for (tmp = highstart_pfn; tmp < highend_pfn; tmp++) {
+		struct page *page = pfn_to_page(tmp);
+
+		if (!memblock_is_memory(PFN_PHYS(tmp)))
+			SetPageReserved(page);
+		else
+			free_highmem_page(page);
+	}
+#endif
+}
+
+void __init mem_init(void)
+{
+	/*
+	 * When _PFN_SHIFT is greater than PAGE_SHIFT we won't have enough PTE
+	 * bits to hold a full 32b physical address on MIPS32 systems.
+	 */
+	BUILD_BUG_ON(IS_ENABLED(CONFIG_32BIT) && (_PFN_SHIFT > PAGE_SHIFT));
+
+	maar_init();
+	memblock_free_all();
+	setup_zero_pages();	/* Setup zeroed pages.  */
+	mem_init_free_highmem();
+
+#ifdef CONFIG_64BIT
+	if ((unsigned long) &_text > (unsigned long) CKSEG0)
+		/* The -4 is a hack so that user tools don't have to handle
+		   the overflow.  */
+		kclist_add(&kcore_kseg0, (void *) CKSEG0,
+				0x80000000 - 4, KCORE_TEXT);
+#endif
+}
+#endif /* !CONFIG_NUMA */
+
+void free_init_pages(const char *what, unsigned long begin, unsigned long end)
+{
+	unsigned long pfn;
+
+	for (pfn = PFN_UP(begin); pfn < PFN_DOWN(end); pfn++) {
+		struct page *page = pfn_to_page(pfn);
+		void *addr = phys_to_virt(PFN_PHYS(pfn));
+
+		memset(addr, POISON_FREE_INITMEM, PAGE_SIZE);
+		free_reserved_page(page);
+	}
+	printk(KERN_INFO "Freeing %s: %ldk freed\n", what, (end - begin) >> 10);
+}
+
+void (*free_init_pages_eva)(void *begin, void *end) = NULL;
+
+void __weak __init prom_free_prom_memory(void)
+{
+	/* nothing to do */
+}
+
+void __ref free_initmem(void)
+{
+	prom_free_prom_memory();
+	/*
+	 * Let the platform define a specific function to free the
+	 * init section since EVA may have used any possible mapping
+	 * between virtual and physical addresses.
+	 */
+	if (free_init_pages_eva)
+		free_init_pages_eva((void *)&__init_begin, (void *)&__init_end);
+	else
+		free_initmem_default(POISON_FREE_INITMEM);
+}
+
+#ifdef CONFIG_HAVE_SETUP_PER_CPU_AREA
+unsigned long __per_cpu_offset[NR_CPUS] __read_mostly;
+EXPORT_SYMBOL(__per_cpu_offset);
+
+static int __init pcpu_cpu_distance(unsigned int from, unsigned int to)
+{
+	return node_distance(cpu_to_node(from), cpu_to_node(to));
+}
+
+static int __init pcpu_cpu_to_node(int cpu)
+{
+	return cpu_to_node(cpu);
+}
+
+void __init setup_per_cpu_areas(void)
+{
+	unsigned long delta;
+	unsigned int cpu;
+	int rc;
+
+	/*
+	 * Always reserve area for module percpu variables.  That's
+	 * what the legacy allocator did.
+	 */
+	rc = pcpu_embed_first_chunk(PERCPU_MODULE_RESERVE,
+				    PERCPU_DYNAMIC_RESERVE, PAGE_SIZE,
+				    pcpu_cpu_distance,
+				    pcpu_cpu_to_node);
+	if (rc < 0)
+		panic("Failed to initialize percpu areas.");
+
+	delta = (unsigned long)pcpu_base_addr - (unsigned long)__per_cpu_start;
+	for_each_possible_cpu(cpu)
+		__per_cpu_offset[cpu] = delta + pcpu_unit_offsets[cpu];
+}
+#endif
+
+#ifndef CONFIG_MIPS_PGD_C0_CONTEXT
+unsigned long pgd_current[NR_CPUS];
+#endif
+
+/*
+ * Align swapper_pg_dir in to 64K, allows its address to be loaded
+ * with a single LUI instruction in the TLB handlers.  If we used
+ * __aligned(64K), its size would get rounded up to the alignment
+ * size, and waste space.  So we place it in its own section and align
+ * it in the linker script.
+ */
+pgd_t swapper_pg_dir[PTRS_PER_PGD] __section(".bss..swapper_pg_dir");
+#ifndef __PAGETABLE_PUD_FOLDED
+pud_t invalid_pud_table[PTRS_PER_PUD] __page_aligned_bss;
+#endif
+#ifndef __PAGETABLE_PMD_FOLDED
+pmd_t invalid_pmd_table[PTRS_PER_PMD] __page_aligned_bss;
+EXPORT_SYMBOL_GPL(invalid_pmd_table);
+#endif
+pte_t invalid_pte_table[PTRS_PER_PTE] __page_aligned_bss;
+EXPORT_SYMBOL(invalid_pte_table);
diff --git a/arch/mips/mm/ioremap.c b/arch/mips/mm/ioremap.c
new file mode 100644
index 000000000..b6dad2fd5
--- /dev/null
+++ b/arch/mips/mm/ioremap.c
@@ -0,0 +1,119 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * (C) Copyright 1995 1996 Linus Torvalds
+ * (C) Copyright 2001, 2002 Ralf Baechle
+ */
+#include <linux/export.h>
+#include <asm/addrspace.h>
+#include <asm/byteorder.h>
+#include <linux/ioport.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/vmalloc.h>
+#include <linux/mm_types.h>
+#include <linux/io.h>
+#include <asm/cacheflush.h>
+#include <asm/tlbflush.h>
+#include <ioremap.h>
+
+#define IS_LOW512(addr) (!((phys_addr_t)(addr) & (phys_addr_t) ~0x1fffffffULL))
+#define IS_KSEG1(addr) (((unsigned long)(addr) & ~0x1fffffffUL) == CKSEG1)
+
+static int __ioremap_check_ram(unsigned long start_pfn, unsigned long nr_pages,
+			       void *arg)
+{
+	unsigned long i;
+
+	for (i = 0; i < nr_pages; i++) {
+		if (pfn_valid(start_pfn + i) &&
+		    !PageReserved(pfn_to_page(start_pfn + i)))
+			return 1;
+	}
+
+	return 0;
+}
+
+/*
+ * ioremap_prot     -   map bus memory into CPU space
+ * @phys_addr:    bus address of the memory
+ * @size:      size of the resource to map
+ *
+ * ioremap_prot gives the caller control over cache coherency attributes (CCA)
+ */
+void __iomem *ioremap_prot(phys_addr_t phys_addr, unsigned long size,
+		unsigned long prot_val)
+{
+	unsigned long flags = prot_val & _CACHE_MASK;
+	unsigned long offset, pfn, last_pfn;
+	struct vm_struct *area;
+	phys_addr_t last_addr;
+	unsigned long vaddr;
+	void __iomem *cpu_addr;
+
+	cpu_addr = plat_ioremap(phys_addr, size, flags);
+	if (cpu_addr)
+		return cpu_addr;
+
+	phys_addr = fixup_bigphys_addr(phys_addr, size);
+
+	/* Don't allow wraparound or zero size */
+	last_addr = phys_addr + size - 1;
+	if (!size || last_addr < phys_addr)
+		return NULL;
+
+	/*
+	 * Map uncached objects in the low 512mb of address space using KSEG1,
+	 * otherwise map using page tables.
+	 */
+	if (IS_LOW512(phys_addr) && IS_LOW512(last_addr) &&
+	    flags == _CACHE_UNCACHED)
+		return (void __iomem *) CKSEG1ADDR(phys_addr);
+
+	/*
+	 * Don't allow anybody to remap RAM that may be allocated by the page
+	 * allocator, since that could lead to races & data clobbering.
+	 */
+	pfn = PFN_DOWN(phys_addr);
+	last_pfn = PFN_DOWN(last_addr);
+	if (walk_system_ram_range(pfn, last_pfn - pfn + 1, NULL,
+				  __ioremap_check_ram) == 1) {
+		WARN_ONCE(1, "ioremap on RAM at %pa - %pa\n",
+			  &phys_addr, &last_addr);
+		return NULL;
+	}
+
+	/*
+	 * Mappings have to be page-aligned
+	 */
+	offset = phys_addr & ~PAGE_MASK;
+	phys_addr &= PAGE_MASK;
+	size = PAGE_ALIGN(last_addr + 1) - phys_addr;
+
+	/*
+	 * Ok, go for it..
+	 */
+	area = get_vm_area(size, VM_IOREMAP);
+	if (!area)
+		return NULL;
+	vaddr = (unsigned long)area->addr;
+
+	flags |= _PAGE_GLOBAL | _PAGE_PRESENT | __READABLE | __WRITEABLE;
+	if (ioremap_page_range(vaddr, vaddr + size, phys_addr,
+			__pgprot(flags))) {
+		free_vm_area(area);
+		return NULL;
+	}
+
+	return (void __iomem *)(vaddr + offset);
+}
+EXPORT_SYMBOL(ioremap_prot);
+
+void iounmap(const volatile void __iomem *addr)
+{
+	if (!plat_iounmap(addr) && !IS_KSEG1(addr))
+		vunmap((void *)((unsigned long)addr & PAGE_MASK));
+}
+EXPORT_SYMBOL(iounmap);
diff --git a/arch/mips/mm/ioremap64.c b/arch/mips/mm/ioremap64.c
new file mode 100644
index 000000000..15e7820d6
--- /dev/null
+++ b/arch/mips/mm/ioremap64.c
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include <linux/io.h>
+#include <ioremap.h>
+
+void __iomem *ioremap_prot(phys_addr_t offset, unsigned long size,
+		unsigned long prot_val)
+{
+	unsigned long flags = prot_val & _CACHE_MASK;
+	u64 base = (flags == _CACHE_UNCACHED ? IO_BASE : UNCAC_BASE);
+	void __iomem *addr;
+
+	addr = plat_ioremap(offset, size, flags);
+	if (!addr)
+		addr = (void __iomem *)(unsigned long)(base + offset);
+	return addr;
+}
+EXPORT_SYMBOL(ioremap_prot);
+
+void iounmap(const volatile void __iomem *addr)
+{
+	plat_iounmap(addr);
+}
+EXPORT_SYMBOL(iounmap);
diff --git a/arch/mips/mm/maccess.c b/arch/mips/mm/maccess.c
new file mode 100644
index 000000000..58173842c
--- /dev/null
+++ b/arch/mips/mm/maccess.c
@@ -0,0 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/uaccess.h>
+#include <linux/kernel.h>
+
+bool copy_from_kernel_nofault_allowed(const void *unsafe_src, size_t size)
+{
+	/* highest bit set means kernel space */
+	return (unsigned long)unsafe_src >> (BITS_PER_LONG - 1);
+}
diff --git a/arch/mips/mm/mmap.c b/arch/mips/mm/mmap.c
new file mode 100644
index 000000000..00fe90c6d
--- /dev/null
+++ b/arch/mips/mm/mmap.c
@@ -0,0 +1,129 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2011 Wind River Systems,
+ *   written by Ralf Baechle <ralf@linux-mips.org>
+ */
+#include <linux/compiler.h>
+#include <linux/elf-randomize.h>
+#include <linux/errno.h>
+#include <linux/mm.h>
+#include <linux/mman.h>
+#include <linux/export.h>
+#include <linux/personality.h>
+#include <linux/random.h>
+#include <linux/sched/signal.h>
+#include <linux/sched/mm.h>
+
+unsigned long shm_align_mask = PAGE_SIZE - 1;	/* Sane caches */
+EXPORT_SYMBOL(shm_align_mask);
+
+#define COLOUR_ALIGN(addr, pgoff)				\
+	((((addr) + shm_align_mask) & ~shm_align_mask) +	\
+	 (((pgoff) << PAGE_SHIFT) & shm_align_mask))
+
+enum mmap_allocation_direction {UP, DOWN};
+
+static unsigned long arch_get_unmapped_area_common(struct file *filp,
+	unsigned long addr0, unsigned long len, unsigned long pgoff,
+	unsigned long flags, enum mmap_allocation_direction dir)
+{
+	struct mm_struct *mm = current->mm;
+	struct vm_area_struct *vma;
+	unsigned long addr = addr0;
+	int do_color_align;
+	struct vm_unmapped_area_info info;
+
+	if (unlikely(len > TASK_SIZE))
+		return -ENOMEM;
+
+	if (flags & MAP_FIXED) {
+		/* Even MAP_FIXED mappings must reside within TASK_SIZE */
+		if (TASK_SIZE - len < addr)
+			return -EINVAL;
+
+		/*
+		 * We do not accept a shared mapping if it would violate
+		 * cache aliasing constraints.
+		 */
+		if ((flags & MAP_SHARED) &&
+		    ((addr - (pgoff << PAGE_SHIFT)) & shm_align_mask))
+			return -EINVAL;
+		return addr;
+	}
+
+	do_color_align = 0;
+	if (filp || (flags & MAP_SHARED))
+		do_color_align = 1;
+
+	/* requesting a specific address */
+	if (addr) {
+		if (do_color_align)
+			addr = COLOUR_ALIGN(addr, pgoff);
+		else
+			addr = PAGE_ALIGN(addr);
+
+		vma = find_vma(mm, addr);
+		if (TASK_SIZE - len >= addr &&
+		    (!vma || addr + len <= vm_start_gap(vma)))
+			return addr;
+	}
+
+	info.length = len;
+	info.align_mask = do_color_align ? (PAGE_MASK & shm_align_mask) : 0;
+	info.align_offset = pgoff << PAGE_SHIFT;
+
+	if (dir == DOWN) {
+		info.flags = VM_UNMAPPED_AREA_TOPDOWN;
+		info.low_limit = PAGE_SIZE;
+		info.high_limit = mm->mmap_base;
+		addr = vm_unmapped_area(&info);
+
+		if (!(addr & ~PAGE_MASK))
+			return addr;
+
+		/*
+		 * A failed mmap() very likely causes application failure,
+		 * so fall back to the bottom-up function here. This scenario
+		 * can happen with large stack limits and large mmap()
+		 * allocations.
+		 */
+	}
+
+	info.flags = 0;
+	info.low_limit = mm->mmap_base;
+	info.high_limit = TASK_SIZE;
+	return vm_unmapped_area(&info);
+}
+
+unsigned long arch_get_unmapped_area(struct file *filp, unsigned long addr0,
+	unsigned long len, unsigned long pgoff, unsigned long flags)
+{
+	return arch_get_unmapped_area_common(filp,
+			addr0, len, pgoff, flags, UP);
+}
+
+/*
+ * There is no need to export this but sched.h declares the function as
+ * extern so making it static here results in an error.
+ */
+unsigned long arch_get_unmapped_area_topdown(struct file *filp,
+	unsigned long addr0, unsigned long len, unsigned long pgoff,
+	unsigned long flags)
+{
+	return arch_get_unmapped_area_common(filp,
+			addr0, len, pgoff, flags, DOWN);
+}
+
+bool __virt_addr_valid(const volatile void *kaddr)
+{
+	unsigned long vaddr = (unsigned long)kaddr;
+
+	if ((vaddr < PAGE_OFFSET) || (vaddr >= MAP_BASE))
+		return false;
+
+	return pfn_valid(PFN_DOWN(virt_to_phys(kaddr)));
+}
+EXPORT_SYMBOL_GPL(__virt_addr_valid);
diff --git a/arch/mips/mm/page-funcs.S b/arch/mips/mm/page-funcs.S
new file mode 100644
index 000000000..43181ac0a
--- /dev/null
+++ b/arch/mips/mm/page-funcs.S
@@ -0,0 +1,53 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Micro-assembler generated clear_page/copy_page functions.
+ *
+ * Copyright (C) 2012  MIPS Technologies, Inc.
+ * Copyright (C) 2012  Ralf Baechle <ralf@linux-mips.org>
+ */
+#include <asm/asm.h>
+#include <asm/export.h>
+#include <asm/regdef.h>
+
+#ifdef CONFIG_SIBYTE_DMA_PAGEOPS
+#define cpu_clear_page_function_name	clear_page_cpu
+#define cpu_copy_page_function_name	copy_page_cpu
+#else
+#define cpu_clear_page_function_name	clear_page
+#define cpu_copy_page_function_name	copy_page
+#endif
+
+/*
+ * Maximum sizes:
+ *
+ * R4000 128 bytes S-cache:		0x058 bytes
+ * R4600 v1.7:				0x05c bytes
+ * R4600 v2.0:				0x060 bytes
+ * With prefetching, 16 word strides	0x120 bytes
+ */
+EXPORT(__clear_page_start)
+LEAF(cpu_clear_page_function_name)
+EXPORT_SYMBOL(cpu_clear_page_function_name)
+1:	j	1b		/* Dummy, will be replaced. */
+	.space 288
+END(cpu_clear_page_function_name)
+EXPORT(__clear_page_end)
+
+/*
+ * Maximum sizes:
+ *
+ * R4000 128 bytes S-cache:		0x11c bytes
+ * R4600 v1.7:				0x080 bytes
+ * R4600 v2.0:				0x07c bytes
+ * With prefetching, 16 word strides	0x540 bytes
+ */
+EXPORT(__copy_page_start)
+LEAF(cpu_copy_page_function_name)
+EXPORT_SYMBOL(cpu_copy_page_function_name)
+1:	j	1b		/* Dummy, will be replaced. */
+	.space 1344
+END(cpu_copy_page_function_name)
+EXPORT(__copy_page_end)
diff --git a/arch/mips/mm/page.c b/arch/mips/mm/page.c
new file mode 100644
index 000000000..d3b4459d0
--- /dev/null
+++ b/arch/mips/mm/page.c
@@ -0,0 +1,682 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003, 04, 05 Ralf Baechle (ralf@linux-mips.org)
+ * Copyright (C) 2007  Maciej W. Rozycki
+ * Copyright (C) 2008  Thiemo Seufer
+ * Copyright (C) 2012  MIPS Technologies, Inc.
+ */
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/smp.h>
+#include <linux/mm.h>
+#include <linux/proc_fs.h>
+
+#include <asm/bugs.h>
+#include <asm/cacheops.h>
+#include <asm/cpu-type.h>
+#include <asm/inst.h>
+#include <asm/io.h>
+#include <asm/page.h>
+#include <asm/prefetch.h>
+#include <asm/bootinfo.h>
+#include <asm/mipsregs.h>
+#include <asm/mmu_context.h>
+#include <asm/cpu.h>
+
+#ifdef CONFIG_SIBYTE_DMA_PAGEOPS
+#include <asm/sibyte/sb1250.h>
+#include <asm/sibyte/sb1250_regs.h>
+#include <asm/sibyte/sb1250_dma.h>
+#endif
+
+#include <asm/uasm.h>
+
+/* Registers used in the assembled routines. */
+#define ZERO 0
+#define AT 2
+#define A0 4
+#define A1 5
+#define A2 6
+#define T0 8
+#define T1 9
+#define T2 10
+#define T3 11
+#define T9 25
+#define RA 31
+
+/* Handle labels (which must be positive integers). */
+enum label_id {
+	label_clear_nopref = 1,
+	label_clear_pref,
+	label_copy_nopref,
+	label_copy_pref_both,
+	label_copy_pref_store,
+};
+
+UASM_L_LA(_clear_nopref)
+UASM_L_LA(_clear_pref)
+UASM_L_LA(_copy_nopref)
+UASM_L_LA(_copy_pref_both)
+UASM_L_LA(_copy_pref_store)
+
+/* We need one branch and therefore one relocation per target label. */
+static struct uasm_label labels[5];
+static struct uasm_reloc relocs[5];
+
+#define cpu_is_r4600_v1_x()	((read_c0_prid() & 0xfffffff0) == 0x00002010)
+#define cpu_is_r4600_v2_x()	((read_c0_prid() & 0xfffffff0) == 0x00002020)
+
+/*
+ * R6 has a limited offset of the pref instruction.
+ * Skip it if the offset is more than 9 bits.
+ */
+#define _uasm_i_pref(a, b, c, d)		\
+do {						\
+	if (cpu_has_mips_r6) {			\
+		if (c <= 0xff && c >= -0x100)	\
+			uasm_i_pref(a, b, c, d);\
+	} else {				\
+		uasm_i_pref(a, b, c, d);	\
+	}					\
+} while(0)
+
+static int pref_bias_clear_store;
+static int pref_bias_copy_load;
+static int pref_bias_copy_store;
+
+static u32 pref_src_mode;
+static u32 pref_dst_mode;
+
+static int clear_word_size;
+static int copy_word_size;
+
+static int half_clear_loop_size;
+static int half_copy_loop_size;
+
+static int cache_line_size;
+#define cache_line_mask() (cache_line_size - 1)
+
+static inline void
+pg_addiu(u32 **buf, unsigned int reg1, unsigned int reg2, unsigned int off)
+{
+	if (cpu_has_64bit_gp_regs &&
+	    IS_ENABLED(CONFIG_CPU_DADDI_WORKAROUNDS) &&
+	    r4k_daddiu_bug()) {
+		if (off > 0x7fff) {
+			uasm_i_lui(buf, T9, uasm_rel_hi(off));
+			uasm_i_addiu(buf, T9, T9, uasm_rel_lo(off));
+		} else
+			uasm_i_addiu(buf, T9, ZERO, off);
+		uasm_i_daddu(buf, reg1, reg2, T9);
+	} else {
+		if (off > 0x7fff) {
+			uasm_i_lui(buf, T9, uasm_rel_hi(off));
+			uasm_i_addiu(buf, T9, T9, uasm_rel_lo(off));
+			UASM_i_ADDU(buf, reg1, reg2, T9);
+		} else
+			UASM_i_ADDIU(buf, reg1, reg2, off);
+	}
+}
+
+static void set_prefetch_parameters(void)
+{
+	if (cpu_has_64bit_gp_regs || cpu_has_64bit_zero_reg)
+		clear_word_size = 8;
+	else
+		clear_word_size = 4;
+
+	if (cpu_has_64bit_gp_regs)
+		copy_word_size = 8;
+	else
+		copy_word_size = 4;
+
+	/*
+	 * The pref's used here are using "streaming" hints, which cause the
+	 * copied data to be kicked out of the cache sooner.  A page copy often
+	 * ends up copying a lot more data than is commonly used, so this seems
+	 * to make sense in terms of reducing cache pollution, but I've no real
+	 * performance data to back this up.
+	 */
+	if (cpu_has_prefetch) {
+		/*
+		 * XXX: Most prefetch bias values in here are based on
+		 * guesswork.
+		 */
+		cache_line_size = cpu_dcache_line_size();
+		switch (current_cpu_type()) {
+		case CPU_R5500:
+		case CPU_TX49XX:
+			/* These processors only support the Pref_Load. */
+			pref_bias_copy_load = 256;
+			break;
+
+		case CPU_R10000:
+		case CPU_R12000:
+		case CPU_R14000:
+		case CPU_R16000:
+			/*
+			 * Those values have been experimentally tuned for an
+			 * Origin 200.
+			 */
+			pref_bias_clear_store = 512;
+			pref_bias_copy_load = 256;
+			pref_bias_copy_store = 256;
+			pref_src_mode = Pref_LoadStreamed;
+			pref_dst_mode = Pref_StoreStreamed;
+			break;
+
+		case CPU_SB1:
+		case CPU_SB1A:
+			pref_bias_clear_store = 128;
+			pref_bias_copy_load = 128;
+			pref_bias_copy_store = 128;
+			/*
+			 * SB1 pass1 Pref_LoadStreamed/Pref_StoreStreamed
+			 * hints are broken.
+			 */
+			if (current_cpu_type() == CPU_SB1 &&
+			    (current_cpu_data.processor_id & 0xff) < 0x02) {
+				pref_src_mode = Pref_Load;
+				pref_dst_mode = Pref_Store;
+			} else {
+				pref_src_mode = Pref_LoadStreamed;
+				pref_dst_mode = Pref_StoreStreamed;
+			}
+			break;
+
+		case CPU_LOONGSON64:
+			/* Loongson-3 only support the Pref_Load/Pref_Store. */
+			pref_bias_clear_store = 128;
+			pref_bias_copy_load = 128;
+			pref_bias_copy_store = 128;
+			pref_src_mode = Pref_Load;
+			pref_dst_mode = Pref_Store;
+			break;
+
+		default:
+			pref_bias_clear_store = 128;
+			pref_bias_copy_load = 256;
+			pref_bias_copy_store = 128;
+			pref_src_mode = Pref_LoadStreamed;
+			if (cpu_has_mips_r6)
+				/*
+				 * Bit 30 (Pref_PrepareForStore) has been
+				 * removed from MIPS R6. Use bit 5
+				 * (Pref_StoreStreamed).
+				 */
+				pref_dst_mode = Pref_StoreStreamed;
+			else
+				pref_dst_mode = Pref_PrepareForStore;
+			break;
+		}
+	} else {
+		if (cpu_has_cache_cdex_s)
+			cache_line_size = cpu_scache_line_size();
+		else if (cpu_has_cache_cdex_p)
+			cache_line_size = cpu_dcache_line_size();
+	}
+	/*
+	 * Too much unrolling will overflow the available space in
+	 * clear_space_array / copy_page_array.
+	 */
+	half_clear_loop_size = min(16 * clear_word_size,
+				   max(cache_line_size >> 1,
+				       4 * clear_word_size));
+	half_copy_loop_size = min(16 * copy_word_size,
+				  max(cache_line_size >> 1,
+				      4 * copy_word_size));
+}
+
+static void build_clear_store(u32 **buf, int off)
+{
+	if (cpu_has_64bit_gp_regs || cpu_has_64bit_zero_reg) {
+		uasm_i_sd(buf, ZERO, off, A0);
+	} else {
+		uasm_i_sw(buf, ZERO, off, A0);
+	}
+}
+
+static inline void build_clear_pref(u32 **buf, int off)
+{
+	if (off & cache_line_mask())
+		return;
+
+	if (pref_bias_clear_store) {
+		_uasm_i_pref(buf, pref_dst_mode, pref_bias_clear_store + off,
+			    A0);
+	} else if (cache_line_size == (half_clear_loop_size << 1)) {
+		if (cpu_has_cache_cdex_s) {
+			uasm_i_cache(buf, Create_Dirty_Excl_SD, off, A0);
+		} else if (cpu_has_cache_cdex_p) {
+			if (IS_ENABLED(CONFIG_WAR_R4600_V1_HIT_CACHEOP) &&
+			    cpu_is_r4600_v1_x()) {
+				uasm_i_nop(buf);
+				uasm_i_nop(buf);
+				uasm_i_nop(buf);
+				uasm_i_nop(buf);
+			}
+
+			if (IS_ENABLED(CONFIG_WAR_R4600_V2_HIT_CACHEOP) &&
+			    cpu_is_r4600_v2_x())
+				uasm_i_lw(buf, ZERO, ZERO, AT);
+
+			uasm_i_cache(buf, Create_Dirty_Excl_D, off, A0);
+		}
+	}
+}
+
+extern u32 __clear_page_start;
+extern u32 __clear_page_end;
+extern u32 __copy_page_start;
+extern u32 __copy_page_end;
+
+void build_clear_page(void)
+{
+	int off;
+	u32 *buf = &__clear_page_start;
+	struct uasm_label *l = labels;
+	struct uasm_reloc *r = relocs;
+	int i;
+	static atomic_t run_once = ATOMIC_INIT(0);
+
+	if (atomic_xchg(&run_once, 1)) {
+		return;
+	}
+
+	memset(labels, 0, sizeof(labels));
+	memset(relocs, 0, sizeof(relocs));
+
+	set_prefetch_parameters();
+
+	/*
+	 * This algorithm makes the following assumptions:
+	 *   - The prefetch bias is a multiple of 2 words.
+	 *   - The prefetch bias is less than one page.
+	 */
+	BUG_ON(pref_bias_clear_store % (2 * clear_word_size));
+	BUG_ON(PAGE_SIZE < pref_bias_clear_store);
+
+	off = PAGE_SIZE - pref_bias_clear_store;
+	if (off > 0xffff || !pref_bias_clear_store)
+		pg_addiu(&buf, A2, A0, off);
+	else
+		uasm_i_ori(&buf, A2, A0, off);
+
+	if (IS_ENABLED(CONFIG_WAR_R4600_V2_HIT_CACHEOP) && cpu_is_r4600_v2_x())
+		uasm_i_lui(&buf, AT, uasm_rel_hi(0xa0000000));
+
+	off = cache_line_size ? min(8, pref_bias_clear_store / cache_line_size)
+				* cache_line_size : 0;
+	while (off) {
+		build_clear_pref(&buf, -off);
+		off -= cache_line_size;
+	}
+	uasm_l_clear_pref(&l, buf);
+	do {
+		build_clear_pref(&buf, off);
+		build_clear_store(&buf, off);
+		off += clear_word_size;
+	} while (off < half_clear_loop_size);
+	pg_addiu(&buf, A0, A0, 2 * off);
+	off = -off;
+	do {
+		build_clear_pref(&buf, off);
+		if (off == -clear_word_size)
+			uasm_il_bne(&buf, &r, A0, A2, label_clear_pref);
+		build_clear_store(&buf, off);
+		off += clear_word_size;
+	} while (off < 0);
+
+	if (pref_bias_clear_store) {
+		pg_addiu(&buf, A2, A0, pref_bias_clear_store);
+		uasm_l_clear_nopref(&l, buf);
+		off = 0;
+		do {
+			build_clear_store(&buf, off);
+			off += clear_word_size;
+		} while (off < half_clear_loop_size);
+		pg_addiu(&buf, A0, A0, 2 * off);
+		off = -off;
+		do {
+			if (off == -clear_word_size)
+				uasm_il_bne(&buf, &r, A0, A2,
+					    label_clear_nopref);
+			build_clear_store(&buf, off);
+			off += clear_word_size;
+		} while (off < 0);
+	}
+
+	uasm_i_jr(&buf, RA);
+	uasm_i_nop(&buf);
+
+	BUG_ON(buf > &__clear_page_end);
+
+	uasm_resolve_relocs(relocs, labels);
+
+	pr_debug("Synthesized clear page handler (%u instructions).\n",
+		 (u32)(buf - &__clear_page_start));
+
+	pr_debug("\t.set push\n");
+	pr_debug("\t.set noreorder\n");
+	for (i = 0; i < (buf - &__clear_page_start); i++)
+		pr_debug("\t.word 0x%08x\n", (&__clear_page_start)[i]);
+	pr_debug("\t.set pop\n");
+}
+
+static void build_copy_load(u32 **buf, int reg, int off)
+{
+	if (cpu_has_64bit_gp_regs) {
+		uasm_i_ld(buf, reg, off, A1);
+	} else {
+		uasm_i_lw(buf, reg, off, A1);
+	}
+}
+
+static void build_copy_store(u32 **buf, int reg, int off)
+{
+	if (cpu_has_64bit_gp_regs) {
+		uasm_i_sd(buf, reg, off, A0);
+	} else {
+		uasm_i_sw(buf, reg, off, A0);
+	}
+}
+
+static inline void build_copy_load_pref(u32 **buf, int off)
+{
+	if (off & cache_line_mask())
+		return;
+
+	if (pref_bias_copy_load)
+		_uasm_i_pref(buf, pref_src_mode, pref_bias_copy_load + off, A1);
+}
+
+static inline void build_copy_store_pref(u32 **buf, int off)
+{
+	if (off & cache_line_mask())
+		return;
+
+	if (pref_bias_copy_store) {
+		_uasm_i_pref(buf, pref_dst_mode, pref_bias_copy_store + off,
+			    A0);
+	} else if (cache_line_size == (half_copy_loop_size << 1)) {
+		if (cpu_has_cache_cdex_s) {
+			uasm_i_cache(buf, Create_Dirty_Excl_SD, off, A0);
+		} else if (cpu_has_cache_cdex_p) {
+			if (IS_ENABLED(CONFIG_WAR_R4600_V1_HIT_CACHEOP) &&
+			    cpu_is_r4600_v1_x()) {
+				uasm_i_nop(buf);
+				uasm_i_nop(buf);
+				uasm_i_nop(buf);
+				uasm_i_nop(buf);
+			}
+
+			if (IS_ENABLED(CONFIG_WAR_R4600_V2_HIT_CACHEOP) &&
+			    cpu_is_r4600_v2_x())
+				uasm_i_lw(buf, ZERO, ZERO, AT);
+
+			uasm_i_cache(buf, Create_Dirty_Excl_D, off, A0);
+		}
+	}
+}
+
+void build_copy_page(void)
+{
+	int off;
+	u32 *buf = &__copy_page_start;
+	struct uasm_label *l = labels;
+	struct uasm_reloc *r = relocs;
+	int i;
+	static atomic_t run_once = ATOMIC_INIT(0);
+
+	if (atomic_xchg(&run_once, 1)) {
+		return;
+	}
+
+	memset(labels, 0, sizeof(labels));
+	memset(relocs, 0, sizeof(relocs));
+
+	set_prefetch_parameters();
+
+	/*
+	 * This algorithm makes the following assumptions:
+	 *   - All prefetch biases are multiples of 8 words.
+	 *   - The prefetch biases are less than one page.
+	 *   - The store prefetch bias isn't greater than the load
+	 *     prefetch bias.
+	 */
+	BUG_ON(pref_bias_copy_load % (8 * copy_word_size));
+	BUG_ON(pref_bias_copy_store % (8 * copy_word_size));
+	BUG_ON(PAGE_SIZE < pref_bias_copy_load);
+	BUG_ON(pref_bias_copy_store > pref_bias_copy_load);
+
+	off = PAGE_SIZE - pref_bias_copy_load;
+	if (off > 0xffff || !pref_bias_copy_load)
+		pg_addiu(&buf, A2, A0, off);
+	else
+		uasm_i_ori(&buf, A2, A0, off);
+
+	if (IS_ENABLED(CONFIG_WAR_R4600_V2_HIT_CACHEOP) && cpu_is_r4600_v2_x())
+		uasm_i_lui(&buf, AT, uasm_rel_hi(0xa0000000));
+
+	off = cache_line_size ? min(8, pref_bias_copy_load / cache_line_size) *
+				cache_line_size : 0;
+	while (off) {
+		build_copy_load_pref(&buf, -off);
+		off -= cache_line_size;
+	}
+	off = cache_line_size ? min(8, pref_bias_copy_store / cache_line_size) *
+				cache_line_size : 0;
+	while (off) {
+		build_copy_store_pref(&buf, -off);
+		off -= cache_line_size;
+	}
+	uasm_l_copy_pref_both(&l, buf);
+	do {
+		build_copy_load_pref(&buf, off);
+		build_copy_load(&buf, T0, off);
+		build_copy_load_pref(&buf, off + copy_word_size);
+		build_copy_load(&buf, T1, off + copy_word_size);
+		build_copy_load_pref(&buf, off + 2 * copy_word_size);
+		build_copy_load(&buf, T2, off + 2 * copy_word_size);
+		build_copy_load_pref(&buf, off + 3 * copy_word_size);
+		build_copy_load(&buf, T3, off + 3 * copy_word_size);
+		build_copy_store_pref(&buf, off);
+		build_copy_store(&buf, T0, off);
+		build_copy_store_pref(&buf, off + copy_word_size);
+		build_copy_store(&buf, T1, off + copy_word_size);
+		build_copy_store_pref(&buf, off + 2 * copy_word_size);
+		build_copy_store(&buf, T2, off + 2 * copy_word_size);
+		build_copy_store_pref(&buf, off + 3 * copy_word_size);
+		build_copy_store(&buf, T3, off + 3 * copy_word_size);
+		off += 4 * copy_word_size;
+	} while (off < half_copy_loop_size);
+	pg_addiu(&buf, A1, A1, 2 * off);
+	pg_addiu(&buf, A0, A0, 2 * off);
+	off = -off;
+	do {
+		build_copy_load_pref(&buf, off);
+		build_copy_load(&buf, T0, off);
+		build_copy_load_pref(&buf, off + copy_word_size);
+		build_copy_load(&buf, T1, off + copy_word_size);
+		build_copy_load_pref(&buf, off + 2 * copy_word_size);
+		build_copy_load(&buf, T2, off + 2 * copy_word_size);
+		build_copy_load_pref(&buf, off + 3 * copy_word_size);
+		build_copy_load(&buf, T3, off + 3 * copy_word_size);
+		build_copy_store_pref(&buf, off);
+		build_copy_store(&buf, T0, off);
+		build_copy_store_pref(&buf, off + copy_word_size);
+		build_copy_store(&buf, T1, off + copy_word_size);
+		build_copy_store_pref(&buf, off + 2 * copy_word_size);
+		build_copy_store(&buf, T2, off + 2 * copy_word_size);
+		build_copy_store_pref(&buf, off + 3 * copy_word_size);
+		if (off == -(4 * copy_word_size))
+			uasm_il_bne(&buf, &r, A2, A0, label_copy_pref_both);
+		build_copy_store(&buf, T3, off + 3 * copy_word_size);
+		off += 4 * copy_word_size;
+	} while (off < 0);
+
+	if (pref_bias_copy_load - pref_bias_copy_store) {
+		pg_addiu(&buf, A2, A0,
+			 pref_bias_copy_load - pref_bias_copy_store);
+		uasm_l_copy_pref_store(&l, buf);
+		off = 0;
+		do {
+			build_copy_load(&buf, T0, off);
+			build_copy_load(&buf, T1, off + copy_word_size);
+			build_copy_load(&buf, T2, off + 2 * copy_word_size);
+			build_copy_load(&buf, T3, off + 3 * copy_word_size);
+			build_copy_store_pref(&buf, off);
+			build_copy_store(&buf, T0, off);
+			build_copy_store_pref(&buf, off + copy_word_size);
+			build_copy_store(&buf, T1, off + copy_word_size);
+			build_copy_store_pref(&buf, off + 2 * copy_word_size);
+			build_copy_store(&buf, T2, off + 2 * copy_word_size);
+			build_copy_store_pref(&buf, off + 3 * copy_word_size);
+			build_copy_store(&buf, T3, off + 3 * copy_word_size);
+			off += 4 * copy_word_size;
+		} while (off < half_copy_loop_size);
+		pg_addiu(&buf, A1, A1, 2 * off);
+		pg_addiu(&buf, A0, A0, 2 * off);
+		off = -off;
+		do {
+			build_copy_load(&buf, T0, off);
+			build_copy_load(&buf, T1, off + copy_word_size);
+			build_copy_load(&buf, T2, off + 2 * copy_word_size);
+			build_copy_load(&buf, T3, off + 3 * copy_word_size);
+			build_copy_store_pref(&buf, off);
+			build_copy_store(&buf, T0, off);
+			build_copy_store_pref(&buf, off + copy_word_size);
+			build_copy_store(&buf, T1, off + copy_word_size);
+			build_copy_store_pref(&buf, off + 2 * copy_word_size);
+			build_copy_store(&buf, T2, off + 2 * copy_word_size);
+			build_copy_store_pref(&buf, off + 3 * copy_word_size);
+			if (off == -(4 * copy_word_size))
+				uasm_il_bne(&buf, &r, A2, A0,
+					    label_copy_pref_store);
+			build_copy_store(&buf, T3, off + 3 * copy_word_size);
+			off += 4 * copy_word_size;
+		} while (off < 0);
+	}
+
+	if (pref_bias_copy_store) {
+		pg_addiu(&buf, A2, A0, pref_bias_copy_store);
+		uasm_l_copy_nopref(&l, buf);
+		off = 0;
+		do {
+			build_copy_load(&buf, T0, off);
+			build_copy_load(&buf, T1, off + copy_word_size);
+			build_copy_load(&buf, T2, off + 2 * copy_word_size);
+			build_copy_load(&buf, T3, off + 3 * copy_word_size);
+			build_copy_store(&buf, T0, off);
+			build_copy_store(&buf, T1, off + copy_word_size);
+			build_copy_store(&buf, T2, off + 2 * copy_word_size);
+			build_copy_store(&buf, T3, off + 3 * copy_word_size);
+			off += 4 * copy_word_size;
+		} while (off < half_copy_loop_size);
+		pg_addiu(&buf, A1, A1, 2 * off);
+		pg_addiu(&buf, A0, A0, 2 * off);
+		off = -off;
+		do {
+			build_copy_load(&buf, T0, off);
+			build_copy_load(&buf, T1, off + copy_word_size);
+			build_copy_load(&buf, T2, off + 2 * copy_word_size);
+			build_copy_load(&buf, T3, off + 3 * copy_word_size);
+			build_copy_store(&buf, T0, off);
+			build_copy_store(&buf, T1, off + copy_word_size);
+			build_copy_store(&buf, T2, off + 2 * copy_word_size);
+			if (off == -(4 * copy_word_size))
+				uasm_il_bne(&buf, &r, A2, A0,
+					    label_copy_nopref);
+			build_copy_store(&buf, T3, off + 3 * copy_word_size);
+			off += 4 * copy_word_size;
+		} while (off < 0);
+	}
+
+	uasm_i_jr(&buf, RA);
+	uasm_i_nop(&buf);
+
+	BUG_ON(buf > &__copy_page_end);
+
+	uasm_resolve_relocs(relocs, labels);
+
+	pr_debug("Synthesized copy page handler (%u instructions).\n",
+		 (u32)(buf - &__copy_page_start));
+
+	pr_debug("\t.set push\n");
+	pr_debug("\t.set noreorder\n");
+	for (i = 0; i < (buf - &__copy_page_start); i++)
+		pr_debug("\t.word 0x%08x\n", (&__copy_page_start)[i]);
+	pr_debug("\t.set pop\n");
+}
+
+#ifdef CONFIG_SIBYTE_DMA_PAGEOPS
+extern void clear_page_cpu(void *page);
+extern void copy_page_cpu(void *to, void *from);
+
+/*
+ * Pad descriptors to cacheline, since each is exclusively owned by a
+ * particular CPU.
+ */
+struct dmadscr {
+	u64 dscr_a;
+	u64 dscr_b;
+	u64 pad_a;
+	u64 pad_b;
+} ____cacheline_aligned_in_smp page_descr[DM_NUM_CHANNELS];
+
+void clear_page(void *page)
+{
+	u64 to_phys = CPHYSADDR((unsigned long)page);
+	unsigned int cpu = smp_processor_id();
+
+	/* if the page is not in KSEG0, use old way */
+	if ((long)KSEGX((unsigned long)page) != (long)CKSEG0)
+		return clear_page_cpu(page);
+
+	page_descr[cpu].dscr_a = to_phys | M_DM_DSCRA_ZERO_MEM |
+				 M_DM_DSCRA_L2C_DEST | M_DM_DSCRA_INTERRUPT;
+	page_descr[cpu].dscr_b = V_DM_DSCRB_SRC_LENGTH(PAGE_SIZE);
+	__raw_writeq(1, IOADDR(A_DM_REGISTER(cpu, R_DM_DSCR_COUNT)));
+
+	/*
+	 * Don't really want to do it this way, but there's no
+	 * reliable way to delay completion detection.
+	 */
+	while (!(__raw_readq(IOADDR(A_DM_REGISTER(cpu, R_DM_DSCR_BASE_DEBUG)))
+		 & M_DM_DSCR_BASE_INTERRUPT))
+		;
+	__raw_readq(IOADDR(A_DM_REGISTER(cpu, R_DM_DSCR_BASE)));
+}
+EXPORT_SYMBOL(clear_page);
+
+void copy_page(void *to, void *from)
+{
+	u64 from_phys = CPHYSADDR((unsigned long)from);
+	u64 to_phys = CPHYSADDR((unsigned long)to);
+	unsigned int cpu = smp_processor_id();
+
+	/* if any page is not in KSEG0, use old way */
+	if ((long)KSEGX((unsigned long)to) != (long)CKSEG0
+	    || (long)KSEGX((unsigned long)from) != (long)CKSEG0)
+		return copy_page_cpu(to, from);
+
+	page_descr[cpu].dscr_a = to_phys | M_DM_DSCRA_L2C_DEST |
+				 M_DM_DSCRA_INTERRUPT;
+	page_descr[cpu].dscr_b = from_phys | V_DM_DSCRB_SRC_LENGTH(PAGE_SIZE);
+	__raw_writeq(1, IOADDR(A_DM_REGISTER(cpu, R_DM_DSCR_COUNT)));
+
+	/*
+	 * Don't really want to do it this way, but there's no
+	 * reliable way to delay completion detection.
+	 */
+	while (!(__raw_readq(IOADDR(A_DM_REGISTER(cpu, R_DM_DSCR_BASE_DEBUG)))
+		 & M_DM_DSCR_BASE_INTERRUPT))
+		;
+	__raw_readq(IOADDR(A_DM_REGISTER(cpu, R_DM_DSCR_BASE)));
+}
+EXPORT_SYMBOL(copy_page);
+
+#endif /* CONFIG_SIBYTE_DMA_PAGEOPS */
diff --git a/arch/mips/mm/pgtable-32.c b/arch/mips/mm/pgtable-32.c
new file mode 100644
index 000000000..61891af25
--- /dev/null
+++ b/arch/mips/mm/pgtable-32.c
@@ -0,0 +1,90 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003 by Ralf Baechle
+ */
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/memblock.h>
+#include <linux/highmem.h>
+#include <asm/fixmap.h>
+#include <asm/pgalloc.h>
+#include <asm/tlbflush.h>
+
+void pgd_init(unsigned long page)
+{
+	unsigned long *p = (unsigned long *) page;
+	int i;
+
+	for (i = 0; i < USER_PTRS_PER_PGD; i+=8) {
+		p[i + 0] = (unsigned long) invalid_pte_table;
+		p[i + 1] = (unsigned long) invalid_pte_table;
+		p[i + 2] = (unsigned long) invalid_pte_table;
+		p[i + 3] = (unsigned long) invalid_pte_table;
+		p[i + 4] = (unsigned long) invalid_pte_table;
+		p[i + 5] = (unsigned long) invalid_pte_table;
+		p[i + 6] = (unsigned long) invalid_pte_table;
+		p[i + 7] = (unsigned long) invalid_pte_table;
+	}
+}
+
+#if defined(CONFIG_TRANSPARENT_HUGEPAGE)
+pmd_t mk_pmd(struct page *page, pgprot_t prot)
+{
+	pmd_t pmd;
+
+	pmd_val(pmd) = (page_to_pfn(page) << _PFN_SHIFT) | pgprot_val(prot);
+
+	return pmd;
+}
+
+
+void set_pmd_at(struct mm_struct *mm, unsigned long addr,
+		pmd_t *pmdp, pmd_t pmd)
+{
+	*pmdp = pmd;
+}
+#endif /* defined(CONFIG_TRANSPARENT_HUGEPAGE) */
+
+void __init pagetable_init(void)
+{
+	unsigned long vaddr;
+	pgd_t *pgd_base;
+#ifdef CONFIG_HIGHMEM
+	pgd_t *pgd;
+	p4d_t *p4d;
+	pud_t *pud;
+	pmd_t *pmd;
+	pte_t *pte;
+#endif
+
+	/* Initialize the entire pgd.  */
+	pgd_init((unsigned long)swapper_pg_dir);
+	pgd_init((unsigned long)swapper_pg_dir
+		 + sizeof(pgd_t) * USER_PTRS_PER_PGD);
+
+	pgd_base = swapper_pg_dir;
+
+	/*
+	 * Fixed mappings:
+	 */
+	vaddr = __fix_to_virt(__end_of_fixed_addresses - 1);
+	fixrange_init(vaddr & PMD_MASK, vaddr + FIXADDR_SIZE, pgd_base);
+
+#ifdef CONFIG_HIGHMEM
+	/*
+	 * Permanent kmaps:
+	 */
+	vaddr = PKMAP_BASE;
+	fixrange_init(vaddr & PMD_MASK, vaddr + PAGE_SIZE*LAST_PKMAP, pgd_base);
+
+	pgd = swapper_pg_dir + pgd_index(vaddr);
+	p4d = p4d_offset(pgd, vaddr);
+	pud = pud_offset(p4d, vaddr);
+	pmd = pmd_offset(pud, vaddr);
+	pte = pte_offset_kernel(pmd, vaddr);
+	pkmap_page_table = pte;
+#endif
+}
diff --git a/arch/mips/mm/pgtable-64.c b/arch/mips/mm/pgtable-64.c
new file mode 100644
index 000000000..7536f7804
--- /dev/null
+++ b/arch/mips/mm/pgtable-64.c
@@ -0,0 +1,124 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1999, 2000 by Silicon Graphics
+ * Copyright (C) 2003 by Ralf Baechle
+ */
+#include <linux/export.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <asm/fixmap.h>
+#include <asm/pgalloc.h>
+#include <asm/tlbflush.h>
+
+void pgd_init(unsigned long page)
+{
+	unsigned long *p, *end;
+	unsigned long entry;
+
+#if !defined(__PAGETABLE_PUD_FOLDED)
+	entry = (unsigned long)invalid_pud_table;
+#elif !defined(__PAGETABLE_PMD_FOLDED)
+	entry = (unsigned long)invalid_pmd_table;
+#else
+	entry = (unsigned long)invalid_pte_table;
+#endif
+
+	p = (unsigned long *) page;
+	end = p + PTRS_PER_PGD;
+
+	do {
+		p[0] = entry;
+		p[1] = entry;
+		p[2] = entry;
+		p[3] = entry;
+		p[4] = entry;
+		p += 8;
+		p[-3] = entry;
+		p[-2] = entry;
+		p[-1] = entry;
+	} while (p != end);
+}
+
+#ifndef __PAGETABLE_PMD_FOLDED
+void pmd_init(unsigned long addr, unsigned long pagetable)
+{
+	unsigned long *p, *end;
+
+	p = (unsigned long *) addr;
+	end = p + PTRS_PER_PMD;
+
+	do {
+		p[0] = pagetable;
+		p[1] = pagetable;
+		p[2] = pagetable;
+		p[3] = pagetable;
+		p[4] = pagetable;
+		p += 8;
+		p[-3] = pagetable;
+		p[-2] = pagetable;
+		p[-1] = pagetable;
+	} while (p != end);
+}
+EXPORT_SYMBOL_GPL(pmd_init);
+#endif
+
+#ifndef __PAGETABLE_PUD_FOLDED
+void pud_init(unsigned long addr, unsigned long pagetable)
+{
+	unsigned long *p, *end;
+
+	p = (unsigned long *)addr;
+	end = p + PTRS_PER_PUD;
+
+	do {
+		p[0] = pagetable;
+		p[1] = pagetable;
+		p[2] = pagetable;
+		p[3] = pagetable;
+		p[4] = pagetable;
+		p += 8;
+		p[-3] = pagetable;
+		p[-2] = pagetable;
+		p[-1] = pagetable;
+	} while (p != end);
+}
+#endif
+
+pmd_t mk_pmd(struct page *page, pgprot_t prot)
+{
+	pmd_t pmd;
+
+	pmd_val(pmd) = (page_to_pfn(page) << _PFN_SHIFT) | pgprot_val(prot);
+
+	return pmd;
+}
+
+void set_pmd_at(struct mm_struct *mm, unsigned long addr,
+		pmd_t *pmdp, pmd_t pmd)
+{
+	*pmdp = pmd;
+}
+
+void __init pagetable_init(void)
+{
+	unsigned long vaddr;
+	pgd_t *pgd_base;
+
+	/* Initialize the entire pgd.  */
+	pgd_init((unsigned long)swapper_pg_dir);
+#ifndef __PAGETABLE_PUD_FOLDED
+	pud_init((unsigned long)invalid_pud_table, (unsigned long)invalid_pmd_table);
+#endif
+#ifndef __PAGETABLE_PMD_FOLDED
+	pmd_init((unsigned long)invalid_pmd_table, (unsigned long)invalid_pte_table);
+#endif
+	pgd_base = swapper_pg_dir;
+	/*
+	 * Fixed mappings:
+	 */
+	vaddr = __fix_to_virt(__end_of_fixed_addresses - 1) & PMD_MASK;
+	fixrange_init(vaddr, vaddr + FIXADDR_SIZE, pgd_base);
+}
diff --git a/arch/mips/mm/pgtable.c b/arch/mips/mm/pgtable.c
new file mode 100644
index 000000000..3b7590660
--- /dev/null
+++ b/arch/mips/mm/pgtable.c
@@ -0,0 +1,25 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#include <linux/export.h>
+#include <linux/mm.h>
+#include <linux/string.h>
+#include <asm/pgalloc.h>
+
+pgd_t *pgd_alloc(struct mm_struct *mm)
+{
+	pgd_t *ret, *init;
+
+	ret = (pgd_t *) __get_free_pages(GFP_KERNEL, PGD_TABLE_ORDER);
+	if (ret) {
+		init = pgd_offset(&init_mm, 0UL);
+		pgd_init((unsigned long)ret);
+		memcpy(ret + USER_PTRS_PER_PGD, init + USER_PTRS_PER_PGD,
+		       (PTRS_PER_PGD - USER_PTRS_PER_PGD) * sizeof(pgd_t));
+	}
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(pgd_alloc);
diff --git a/arch/mips/mm/physaddr.c b/arch/mips/mm/physaddr.c
new file mode 100644
index 000000000..f9b8c85e9
--- /dev/null
+++ b/arch/mips/mm/physaddr.c
@@ -0,0 +1,50 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/bug.h>
+#include <linux/export.h>
+#include <linux/types.h>
+#include <linux/mmdebug.h>
+#include <linux/mm.h>
+
+#include <asm/addrspace.h>
+#include <asm/sections.h>
+#include <asm/io.h>
+#include <asm/page.h>
+#include <asm/dma.h>
+
+static inline bool __debug_virt_addr_valid(unsigned long x)
+{
+	/*
+	 * MAX_DMA_ADDRESS is a virtual address that may not correspond to an
+	 * actual physical address. Enough code relies on
+	 * virt_to_phys(MAX_DMA_ADDRESS) that we just need to work around it
+	 * and always return true.
+	 */
+	if (x == MAX_DMA_ADDRESS)
+		return true;
+
+	return x >= PAGE_OFFSET && (KSEGX(x) < KSEG2 ||
+	       IS_ENABLED(CONFIG_EVA) ||
+	       !IS_ENABLED(CONFIG_HIGHMEM));
+}
+
+phys_addr_t __virt_to_phys(volatile const void *x)
+{
+	WARN(!__debug_virt_addr_valid((unsigned long)x),
+	     "virt_to_phys used for non-linear address: %pK (%pS)\n",
+	     x, x);
+
+	return __virt_to_phys_nodebug(x);
+}
+EXPORT_SYMBOL(__virt_to_phys);
+
+phys_addr_t __phys_addr_symbol(unsigned long x)
+{
+	/* This is bounds checking against the kernel image only.
+	 * __pa_symbol should only be used on kernel symbol addresses.
+	 */
+	VIRTUAL_BUG_ON(x < (unsigned long)_text ||
+		       x > (unsigned long)_end);
+
+	return __pa_symbol_nodebug(x);
+}
+EXPORT_SYMBOL(__phys_addr_symbol);
diff --git a/arch/mips/mm/sc-debugfs.c b/arch/mips/mm/sc-debugfs.c
new file mode 100644
index 000000000..80ff39471
--- /dev/null
+++ b/arch/mips/mm/sc-debugfs.c
@@ -0,0 +1,61 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2015 Imagination Technologies
+ * Author: Paul Burton <paul.burton@mips.com>
+ */
+
+#include <asm/bcache.h>
+#include <asm/debug.h>
+#include <linux/uaccess.h>
+#include <linux/debugfs.h>
+#include <linux/init.h>
+
+static ssize_t sc_prefetch_read(struct file *file, char __user *user_buf,
+				size_t count, loff_t *ppos)
+{
+	bool enabled = bc_prefetch_is_enabled();
+	char buf[3];
+
+	buf[0] = enabled ? 'Y' : 'N';
+	buf[1] = '\n';
+	buf[2] = 0;
+
+	return simple_read_from_buffer(user_buf, count, ppos, buf, 2);
+}
+
+static ssize_t sc_prefetch_write(struct file *file,
+				 const char __user *user_buf,
+				 size_t count, loff_t *ppos)
+{
+	bool enabled;
+	int err;
+
+	err = kstrtobool_from_user(user_buf, count, &enabled);
+	if (err)
+		return err;
+
+	if (enabled)
+		bc_prefetch_enable();
+	else
+		bc_prefetch_disable();
+
+	return count;
+}
+
+static const struct file_operations sc_prefetch_fops = {
+	.open = simple_open,
+	.llseek = default_llseek,
+	.read = sc_prefetch_read,
+	.write = sc_prefetch_write,
+};
+
+static int __init sc_debugfs_init(void)
+{
+	struct dentry *dir;
+
+	dir = debugfs_create_dir("l2cache", mips_debugfs_dir);
+	debugfs_create_file("prefetch", S_IRUGO | S_IWUSR, dir, NULL,
+			    &sc_prefetch_fops);
+	return 0;
+}
+late_initcall(sc_debugfs_init);
diff --git a/arch/mips/mm/sc-ip22.c b/arch/mips/mm/sc-ip22.c
new file mode 100644
index 000000000..d7238687d
--- /dev/null
+++ b/arch/mips/mm/sc-ip22.c
@@ -0,0 +1,190 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * sc-ip22.c: Indy cache management functions.
+ *
+ * Copyright (C) 1997, 2001 Ralf Baechle (ralf@gnu.org),
+ * derived from r4xx0.c by David S. Miller (davem@davemloft.net).
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/mm.h>
+
+#include <asm/bcache.h>
+#include <asm/page.h>
+#include <asm/bootinfo.h>
+#include <asm/sgi/ip22.h>
+#include <asm/sgi/mc.h>
+
+/* Secondary cache size in bytes, if present.  */
+static unsigned long scache_size;
+
+#undef DEBUG_CACHE
+
+#define SC_SIZE 0x00080000
+#define SC_LINE 32
+#define CI_MASK (SC_SIZE - SC_LINE)
+#define SC_INDEX(n) ((n) & CI_MASK)
+
+static inline void indy_sc_wipe(unsigned long first, unsigned long last)
+{
+	unsigned long tmp;
+
+	__asm__ __volatile__(
+	"	.set	push			# indy_sc_wipe		\n"
+	"	.set	noreorder					\n"
+	"	.set	mips3						\n"
+	"	.set	noat						\n"
+	"	mfc0	%2, $12						\n"
+	"	li	$1, 0x80		# Go 64 bit		\n"
+	"	mtc0	$1, $12						\n"
+	"								\n"
+	"	#							\n"
+	"	# Open code a dli $1, 0x9000000080000000		\n"
+	"	#							\n"
+	"	# Required because binutils 2.25 will happily accept	\n"
+	"	# 64 bit instructions in .set mips3 mode but puke on	\n"
+	"	# 64 bit constants when generating 32 bit ELF		\n"
+	"	#							\n"
+	"	lui	$1,0x9000					\n"
+	"	dsll	$1,$1,0x10					\n"
+	"	ori	$1,$1,0x8000					\n"
+	"	dsll	$1,$1,0x10					\n"
+	"								\n"
+	"	or	%0, $1			# first line to flush	\n"
+	"	or	%1, $1			# last line to flush	\n"
+	"	.set	at						\n"
+	"								\n"
+	"1:	sw	$0, 0(%0)					\n"
+	"	bne	%0, %1, 1b					\n"
+	"	 daddu	%0, 32						\n"
+	"								\n"
+	"	mtc0	%2, $12			# Back to 32 bit	\n"
+	"	nop				# pipeline hazard	\n"
+	"	nop							\n"
+	"	nop							\n"
+	"	nop							\n"
+	"	.set	pop						\n"
+	: "=r" (first), "=r" (last), "=&r" (tmp)
+	: "0" (first), "1" (last));
+}
+
+static void indy_sc_wback_invalidate(unsigned long addr, unsigned long size)
+{
+	unsigned long first_line, last_line;
+	unsigned long flags;
+
+#ifdef DEBUG_CACHE
+	printk("indy_sc_wback_invalidate[%08lx,%08lx]", addr, size);
+#endif
+
+	/* Catch bad driver code */
+	BUG_ON(size == 0);
+
+	/* Which lines to flush?  */
+	first_line = SC_INDEX(addr);
+	last_line = SC_INDEX(addr + size - 1);
+
+	local_irq_save(flags);
+	if (first_line <= last_line) {
+		indy_sc_wipe(first_line, last_line);
+		goto out;
+	}
+
+	indy_sc_wipe(first_line, SC_SIZE - SC_LINE);
+	indy_sc_wipe(0, last_line);
+out:
+	local_irq_restore(flags);
+}
+
+static void indy_sc_enable(void)
+{
+	unsigned long addr, tmp1, tmp2;
+
+	/* This is really cool... */
+#ifdef DEBUG_CACHE
+	printk("Enabling R4600 SCACHE\n");
+#endif
+	__asm__ __volatile__(
+	".set\tpush\n\t"
+	".set\tnoreorder\n\t"
+	".set\tmips3\n\t"
+	"mfc0\t%2, $12\n\t"
+	"nop; nop; nop; nop;\n\t"
+	"li\t%1, 0x80\n\t"
+	"mtc0\t%1, $12\n\t"
+	"nop; nop; nop; nop;\n\t"
+	"li\t%0, 0x1\n\t"
+	"dsll\t%0, 31\n\t"
+	"lui\t%1, 0x9000\n\t"
+	"dsll32\t%1, 0\n\t"
+	"or\t%0, %1, %0\n\t"
+	"sb\t$0, 0(%0)\n\t"
+	"mtc0\t$0, $12\n\t"
+	"nop; nop; nop; nop;\n\t"
+	"mtc0\t%2, $12\n\t"
+	"nop; nop; nop; nop;\n\t"
+	".set\tpop"
+	: "=r" (tmp1), "=r" (tmp2), "=r" (addr));
+}
+
+static void indy_sc_disable(void)
+{
+	unsigned long tmp1, tmp2, tmp3;
+
+#ifdef DEBUG_CACHE
+	printk("Disabling R4600 SCACHE\n");
+#endif
+	__asm__ __volatile__(
+	".set\tpush\n\t"
+	".set\tnoreorder\n\t"
+	".set\tmips3\n\t"
+	"li\t%0, 0x1\n\t"
+	"dsll\t%0, 31\n\t"
+	"lui\t%1, 0x9000\n\t"
+	"dsll32\t%1, 0\n\t"
+	"or\t%0, %1, %0\n\t"
+	"mfc0\t%2, $12\n\t"
+	"nop; nop; nop; nop\n\t"
+	"li\t%1, 0x80\n\t"
+	"mtc0\t%1, $12\n\t"
+	"nop; nop; nop; nop\n\t"
+	"sh\t$0, 0(%0)\n\t"
+	"mtc0\t$0, $12\n\t"
+	"nop; nop; nop; nop\n\t"
+	"mtc0\t%2, $12\n\t"
+	"nop; nop; nop; nop\n\t"
+	".set\tpop"
+	: "=r" (tmp1), "=r" (tmp2), "=r" (tmp3));
+}
+
+static inline int __init indy_sc_probe(void)
+{
+	unsigned int size = ip22_eeprom_read(&sgimc->eeprom, 17);
+	if (size == 0)
+		return 0;
+
+	size <<= PAGE_SHIFT;
+	printk(KERN_INFO "R4600/R5000 SCACHE size %dK, linesize 32 bytes.\n",
+	       size >> 10);
+	scache_size = size;
+
+	return 1;
+}
+
+/* XXX Check with wje if the Indy caches can differentiate between
+   writeback + invalidate and just invalidate.	*/
+static struct bcache_ops indy_sc_ops = {
+	.bc_enable = indy_sc_enable,
+	.bc_disable = indy_sc_disable,
+	.bc_wback_inv = indy_sc_wback_invalidate,
+	.bc_inv = indy_sc_wback_invalidate
+};
+
+void indy_sc_init(void)
+{
+	if (indy_sc_probe()) {
+		indy_sc_enable();
+		bcops = &indy_sc_ops;
+	}
+}
diff --git a/arch/mips/mm/sc-mips.c b/arch/mips/mm/sc-mips.c
new file mode 100644
index 000000000..06ec304ad
--- /dev/null
+++ b/arch/mips/mm/sc-mips.c
@@ -0,0 +1,264 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2006 Chris Dearman (chris@mips.com),
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/mm.h>
+
+#include <asm/cpu-type.h>
+#include <asm/mipsregs.h>
+#include <asm/bcache.h>
+#include <asm/cacheops.h>
+#include <asm/page.h>
+#include <asm/mmu_context.h>
+#include <asm/r4kcache.h>
+#include <asm/mips-cps.h>
+#include <asm/bootinfo.h>
+
+/*
+ * MIPS32/MIPS64 L2 cache handling
+ */
+
+/*
+ * Writeback and invalidate the secondary cache before DMA.
+ */
+static void mips_sc_wback_inv(unsigned long addr, unsigned long size)
+{
+	blast_scache_range(addr, addr + size);
+}
+
+/*
+ * Invalidate the secondary cache before DMA.
+ */
+static void mips_sc_inv(unsigned long addr, unsigned long size)
+{
+	unsigned long lsize = cpu_scache_line_size();
+	unsigned long almask = ~(lsize - 1);
+
+	cache_op(Hit_Writeback_Inv_SD, addr & almask);
+	cache_op(Hit_Writeback_Inv_SD, (addr + size - 1) & almask);
+	blast_inv_scache_range(addr, addr + size);
+}
+
+static void mips_sc_enable(void)
+{
+	/* L2 cache is permanently enabled */
+}
+
+static void mips_sc_disable(void)
+{
+	/* L2 cache is permanently enabled */
+}
+
+static void mips_sc_prefetch_enable(void)
+{
+	unsigned long pftctl;
+
+	if (mips_cm_revision() < CM_REV_CM2_5)
+		return;
+
+	/*
+	 * If there is one or more L2 prefetch unit present then enable
+	 * prefetching for both code & data, for all ports.
+	 */
+	pftctl = read_gcr_l2_pft_control();
+	if (pftctl & CM_GCR_L2_PFT_CONTROL_NPFT) {
+		pftctl &= ~CM_GCR_L2_PFT_CONTROL_PAGEMASK;
+		pftctl |= PAGE_MASK & CM_GCR_L2_PFT_CONTROL_PAGEMASK;
+		pftctl |= CM_GCR_L2_PFT_CONTROL_PFTEN;
+		write_gcr_l2_pft_control(pftctl);
+
+		set_gcr_l2_pft_control_b(CM_GCR_L2_PFT_CONTROL_B_PORTID |
+					 CM_GCR_L2_PFT_CONTROL_B_CEN);
+	}
+}
+
+static void mips_sc_prefetch_disable(void)
+{
+	if (mips_cm_revision() < CM_REV_CM2_5)
+		return;
+
+	clear_gcr_l2_pft_control(CM_GCR_L2_PFT_CONTROL_PFTEN);
+	clear_gcr_l2_pft_control_b(CM_GCR_L2_PFT_CONTROL_B_PORTID |
+				   CM_GCR_L2_PFT_CONTROL_B_CEN);
+}
+
+static bool mips_sc_prefetch_is_enabled(void)
+{
+	unsigned long pftctl;
+
+	if (mips_cm_revision() < CM_REV_CM2_5)
+		return false;
+
+	pftctl = read_gcr_l2_pft_control();
+	if (!(pftctl & CM_GCR_L2_PFT_CONTROL_NPFT))
+		return false;
+	return !!(pftctl & CM_GCR_L2_PFT_CONTROL_PFTEN);
+}
+
+static struct bcache_ops mips_sc_ops = {
+	.bc_enable = mips_sc_enable,
+	.bc_disable = mips_sc_disable,
+	.bc_wback_inv = mips_sc_wback_inv,
+	.bc_inv = mips_sc_inv,
+	.bc_prefetch_enable = mips_sc_prefetch_enable,
+	.bc_prefetch_disable = mips_sc_prefetch_disable,
+	.bc_prefetch_is_enabled = mips_sc_prefetch_is_enabled,
+};
+
+/*
+ * Check if the L2 cache controller is activated on a particular platform.
+ * MTI's L2 controller and the L2 cache controller of Broadcom's BMIPS
+ * cores both use c0_config2's bit 12 as "L2 Bypass" bit, that is the
+ * cache being disabled.  However there is no guarantee for this to be
+ * true on all platforms.  In an act of stupidity the spec defined bits
+ * 12..15 as implementation defined so below function will eventually have
+ * to be replaced by a platform specific probe.
+ */
+static inline int mips_sc_is_activated(struct cpuinfo_mips *c)
+{
+	unsigned int config2 = read_c0_config2();
+	unsigned int tmp;
+
+	/* Check the bypass bit (L2B) */
+	switch (current_cpu_type()) {
+	case CPU_34K:
+	case CPU_74K:
+	case CPU_1004K:
+	case CPU_1074K:
+	case CPU_INTERAPTIV:
+	case CPU_PROAPTIV:
+	case CPU_P5600:
+	case CPU_BMIPS5000:
+	case CPU_QEMU_GENERIC:
+	case CPU_P6600:
+		if (config2 & (1 << 12))
+			return 0;
+	}
+
+	tmp = (config2 >> 4) & 0x0f;
+	if (0 < tmp && tmp <= 7)
+		c->scache.linesz = 2 << tmp;
+	else
+		return 0;
+	return 1;
+}
+
+static int mips_sc_probe_cm3(void)
+{
+	struct cpuinfo_mips *c = &current_cpu_data;
+	unsigned long cfg = read_gcr_l2_config();
+	unsigned long sets, line_sz, assoc;
+
+	if (cfg & CM_GCR_L2_CONFIG_BYPASS)
+		return 0;
+
+	sets = cfg & CM_GCR_L2_CONFIG_SET_SIZE;
+	sets >>= __ffs(CM_GCR_L2_CONFIG_SET_SIZE);
+	if (sets)
+		c->scache.sets = 64 << sets;
+
+	line_sz = cfg & CM_GCR_L2_CONFIG_LINE_SIZE;
+	line_sz >>= __ffs(CM_GCR_L2_CONFIG_LINE_SIZE);
+	if (line_sz)
+		c->scache.linesz = 2 << line_sz;
+
+	assoc = cfg & CM_GCR_L2_CONFIG_ASSOC;
+	assoc >>= __ffs(CM_GCR_L2_CONFIG_ASSOC);
+	c->scache.ways = assoc + 1;
+	c->scache.waysize = c->scache.sets * c->scache.linesz;
+	c->scache.waybit = __ffs(c->scache.waysize);
+
+	if (c->scache.linesz) {
+		c->scache.flags &= ~MIPS_CACHE_NOT_PRESENT;
+		c->options |= MIPS_CPU_INCLUSIVE_CACHES;
+		return 1;
+	}
+
+	return 0;
+}
+
+static inline int mips_sc_probe(void)
+{
+	struct cpuinfo_mips *c = &current_cpu_data;
+	unsigned int config1, config2;
+	unsigned int tmp;
+
+	/* Mark as not present until probe completed */
+	c->scache.flags |= MIPS_CACHE_NOT_PRESENT;
+
+	if (mips_cm_revision() >= CM_REV_CM3)
+		return mips_sc_probe_cm3();
+
+	/* Ignore anything but MIPSxx processors */
+	if (!(c->isa_level & (MIPS_CPU_ISA_M32R1 | MIPS_CPU_ISA_M64R1 |
+			      MIPS_CPU_ISA_M32R2 | MIPS_CPU_ISA_M64R2 |
+			      MIPS_CPU_ISA_M32R5 | MIPS_CPU_ISA_M64R5 |
+			      MIPS_CPU_ISA_M32R6 | MIPS_CPU_ISA_M64R6)))
+		return 0;
+
+	/* Does this MIPS32/MIPS64 CPU have a config2 register? */
+	config1 = read_c0_config1();
+	if (!(config1 & MIPS_CONF_M))
+		return 0;
+
+	config2 = read_c0_config2();
+
+	if (!mips_sc_is_activated(c))
+		return 0;
+
+	tmp = (config2 >> 8) & 0x0f;
+	if (tmp <= 7)
+		c->scache.sets = 64 << tmp;
+	else
+		return 0;
+
+	tmp = (config2 >> 0) & 0x0f;
+	if (tmp <= 7)
+		c->scache.ways = tmp + 1;
+	else
+		return 0;
+
+	if (current_cpu_type() == CPU_XBURST) {
+		switch (mips_machtype) {
+		/*
+		 * According to config2 it would be 5-ways, but that is
+		 * contradicted by all documentation.
+		 */
+		case MACH_INGENIC_JZ4770:
+		case MACH_INGENIC_JZ4775:
+			c->scache.ways = 4;
+			break;
+
+		/*
+		 * According to config2 it would be 5-ways and 512-sets,
+		 * but that is contradicted by all documentation.
+		 */
+		case MACH_INGENIC_X1000:
+		case MACH_INGENIC_X1000E:
+			c->scache.sets = 256;
+			c->scache.ways = 4;
+			break;
+		}
+	}
+
+	c->scache.waysize = c->scache.sets * c->scache.linesz;
+	c->scache.waybit = __ffs(c->scache.waysize);
+
+	c->scache.flags &= ~MIPS_CACHE_NOT_PRESENT;
+
+	return 1;
+}
+
+int mips_sc_init(void)
+{
+	int found = mips_sc_probe();
+	if (found) {
+		mips_sc_enable();
+		mips_sc_prefetch_enable();
+		bcops = &mips_sc_ops;
+	}
+	return found;
+}
diff --git a/arch/mips/mm/sc-r5k.c b/arch/mips/mm/sc-r5k.c
new file mode 100644
index 000000000..736615d68
--- /dev/null
+++ b/arch/mips/mm/sc-r5k.c
@@ -0,0 +1,107 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 1997, 2001 Ralf Baechle (ralf@gnu.org),
+ * derived from r4xx0.c by David S. Miller (davem@davemloft.net).
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/mm.h>
+
+#include <asm/mipsregs.h>
+#include <asm/bcache.h>
+#include <asm/cacheops.h>
+#include <asm/page.h>
+#include <asm/mmu_context.h>
+#include <asm/r4kcache.h>
+
+/* Secondary cache size in bytes, if present.  */
+static unsigned long scache_size;
+
+#define SC_LINE 32
+#define SC_PAGE (128*SC_LINE)
+
+static inline void blast_r5000_scache(void)
+{
+	unsigned long start = INDEX_BASE;
+	unsigned long end = start + scache_size;
+
+	while(start < end) {
+		cache_op(R5K_Page_Invalidate_S, start);
+		start += SC_PAGE;
+	}
+}
+
+static void r5k_dma_cache_inv_sc(unsigned long addr, unsigned long size)
+{
+	unsigned long end, a;
+
+	/* Catch bad driver code */
+	BUG_ON(size == 0);
+
+	if (size >= scache_size) {
+		blast_r5000_scache();
+		return;
+	}
+
+	/* On the R5000 secondary cache we cannot
+	 * invalidate less than a page at a time.
+	 * The secondary cache is physically indexed, write-through.
+	 */
+	a = addr & ~(SC_PAGE - 1);
+	end = (addr + size - 1) & ~(SC_PAGE - 1);
+	while (a <= end) {
+		cache_op(R5K_Page_Invalidate_S, a);
+		a += SC_PAGE;
+	}
+}
+
+static void r5k_sc_enable(void)
+{
+	unsigned long flags;
+
+	local_irq_save(flags);
+	set_c0_config(R5K_CONF_SE);
+	blast_r5000_scache();
+	local_irq_restore(flags);
+}
+
+static void r5k_sc_disable(void)
+{
+	unsigned long flags;
+
+	local_irq_save(flags);
+	blast_r5000_scache();
+	clear_c0_config(R5K_CONF_SE);
+	local_irq_restore(flags);
+}
+
+static inline int __init r5k_sc_probe(void)
+{
+	unsigned long config = read_c0_config();
+
+	if (config & CONF_SC)
+		return 0;
+
+	scache_size = (512 * 1024) << ((config & R5K_CONF_SS) >> 20);
+
+	printk("R5000 SCACHE size %ldkB, linesize 32 bytes.\n",
+			scache_size >> 10);
+
+	return 1;
+}
+
+static struct bcache_ops r5k_sc_ops = {
+	.bc_enable = r5k_sc_enable,
+	.bc_disable = r5k_sc_disable,
+	.bc_wback_inv = r5k_dma_cache_inv_sc,
+	.bc_inv = r5k_dma_cache_inv_sc
+};
+
+void r5k_sc_init(void)
+{
+	if (r5k_sc_probe()) {
+		r5k_sc_enable();
+		bcops = &r5k_sc_ops;
+	}
+}
diff --git a/arch/mips/mm/sc-rm7k.c b/arch/mips/mm/sc-rm7k.c
new file mode 100644
index 000000000..e9e3777a7
--- /dev/null
+++ b/arch/mips/mm/sc-rm7k.c
@@ -0,0 +1,270 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * sc-rm7k.c: RM7000 cache management functions.
+ *
+ * Copyright (C) 1997, 2001, 2003, 2004 Ralf Baechle (ralf@linux-mips.org)
+ */
+
+#undef DEBUG
+
+#include <linux/kernel.h>
+#include <linux/mm.h>
+#include <linux/bitops.h>
+
+#include <asm/addrspace.h>
+#include <asm/bcache.h>
+#include <asm/cacheops.h>
+#include <asm/mipsregs.h>
+#include <asm/processor.h>
+#include <asm/sections.h>
+#include <asm/cacheflush.h> /* for run_uncached() */
+
+/* Primary cache parameters. */
+#define sc_lsize	32
+#define tc_pagesize	(32*128)
+
+/* Secondary cache parameters. */
+#define scache_size	(256*1024)	/* Fixed to 256KiB on RM7000 */
+
+/* Tertiary cache parameters */
+#define tc_lsize	32
+
+extern unsigned long icache_way_size, dcache_way_size;
+static unsigned long tcache_size;
+
+#include <asm/r4kcache.h>
+
+static int rm7k_tcache_init;
+
+/*
+ * Writeback and invalidate the primary cache dcache before DMA.
+ * (XXX These need to be fixed ...)
+ */
+static void rm7k_sc_wback_inv(unsigned long addr, unsigned long size)
+{
+	unsigned long end, a;
+
+	pr_debug("rm7k_sc_wback_inv[%08lx,%08lx]", addr, size);
+
+	/* Catch bad driver code */
+	BUG_ON(size == 0);
+
+	blast_scache_range(addr, addr + size);
+
+	if (!rm7k_tcache_init)
+		return;
+
+	a = addr & ~(tc_pagesize - 1);
+	end = (addr + size - 1) & ~(tc_pagesize - 1);
+	while(1) {
+		invalidate_tcache_page(a);	/* Page_Invalidate_T */
+		if (a == end)
+			break;
+		a += tc_pagesize;
+	}
+}
+
+static void rm7k_sc_inv(unsigned long addr, unsigned long size)
+{
+	unsigned long end, a;
+
+	pr_debug("rm7k_sc_inv[%08lx,%08lx]", addr, size);
+
+	/* Catch bad driver code */
+	BUG_ON(size == 0);
+
+	blast_inv_scache_range(addr, addr + size);
+
+	if (!rm7k_tcache_init)
+		return;
+
+	a = addr & ~(tc_pagesize - 1);
+	end = (addr + size - 1) & ~(tc_pagesize - 1);
+	while(1) {
+		invalidate_tcache_page(a);	/* Page_Invalidate_T */
+		if (a == end)
+			break;
+		a += tc_pagesize;
+	}
+}
+
+static void blast_rm7k_tcache(void)
+{
+	unsigned long start = CKSEG0ADDR(0);
+	unsigned long end = start + tcache_size;
+
+	write_c0_taglo(0);
+
+	while (start < end) {
+		cache_op(Page_Invalidate_T, start);
+		start += tc_pagesize;
+	}
+}
+
+/*
+ * This function is executed in uncached address space.
+ */
+static void __rm7k_tc_enable(void)
+{
+	int i;
+
+	set_c0_config(RM7K_CONF_TE);
+
+	write_c0_taglo(0);
+	write_c0_taghi(0);
+
+	for (i = 0; i < tcache_size; i += tc_lsize)
+		cache_op(Index_Store_Tag_T, CKSEG0ADDR(i));
+}
+
+static void rm7k_tc_enable(void)
+{
+	if (read_c0_config() & RM7K_CONF_TE)
+		return;
+
+	BUG_ON(tcache_size == 0);
+
+	run_uncached(__rm7k_tc_enable);
+}
+
+/*
+ * This function is executed in uncached address space.
+ */
+static void __rm7k_sc_enable(void)
+{
+	int i;
+
+	set_c0_config(RM7K_CONF_SE);
+
+	write_c0_taglo(0);
+	write_c0_taghi(0);
+
+	for (i = 0; i < scache_size; i += sc_lsize)
+		cache_op(Index_Store_Tag_SD, CKSEG0ADDR(i));
+}
+
+static void rm7k_sc_enable(void)
+{
+	if (read_c0_config() & RM7K_CONF_SE)
+		return;
+
+	pr_info("Enabling secondary cache...\n");
+	run_uncached(__rm7k_sc_enable);
+
+	if (rm7k_tcache_init)
+		rm7k_tc_enable();
+}
+
+static void rm7k_tc_disable(void)
+{
+	unsigned long flags;
+
+	local_irq_save(flags);
+	blast_rm7k_tcache();
+	clear_c0_config(RM7K_CONF_TE);
+	local_irq_restore(flags);
+}
+
+static void rm7k_sc_disable(void)
+{
+	clear_c0_config(RM7K_CONF_SE);
+
+	if (rm7k_tcache_init)
+		rm7k_tc_disable();
+}
+
+static struct bcache_ops rm7k_sc_ops = {
+	.bc_enable = rm7k_sc_enable,
+	.bc_disable = rm7k_sc_disable,
+	.bc_wback_inv = rm7k_sc_wback_inv,
+	.bc_inv = rm7k_sc_inv
+};
+
+/*
+ * This is a probing function like the one found in c-r4k.c, we look for the
+ * wrap around point with different addresses.
+ */
+static void __probe_tcache(void)
+{
+	unsigned long flags, addr, begin, end, pow2;
+
+	begin = (unsigned long) &_stext;
+	begin  &= ~((8 * 1024 * 1024) - 1);
+	end = begin + (8 * 1024 * 1024);
+
+	local_irq_save(flags);
+
+	set_c0_config(RM7K_CONF_TE);
+
+	/* Fill size-multiple lines with a valid tag */
+	pow2 = (256 * 1024);
+	for (addr = begin; addr <= end; addr = (begin + pow2)) {
+		unsigned long *p = (unsigned long *) addr;
+		__asm__ __volatile__("nop" : : "r" (*p));
+		pow2 <<= 1;
+	}
+
+	/* Load first line with a 0 tag, to check after */
+	write_c0_taglo(0);
+	write_c0_taghi(0);
+	cache_op(Index_Store_Tag_T, begin);
+
+	/* Look for the wrap-around */
+	pow2 = (512 * 1024);
+	for (addr = begin + (512 * 1024); addr <= end; addr = begin + pow2) {
+		cache_op(Index_Load_Tag_T, addr);
+		if (!read_c0_taglo())
+			break;
+		pow2 <<= 1;
+	}
+
+	addr -= begin;
+	tcache_size = addr;
+
+	clear_c0_config(RM7K_CONF_TE);
+
+	local_irq_restore(flags);
+}
+
+void rm7k_sc_init(void)
+{
+	struct cpuinfo_mips *c = &current_cpu_data;
+	unsigned int config = read_c0_config();
+
+	if ((config & RM7K_CONF_SC))
+		return;
+
+	c->scache.linesz = sc_lsize;
+	c->scache.ways = 4;
+	c->scache.waybit= __ffs(scache_size / c->scache.ways);
+	c->scache.waysize = scache_size / c->scache.ways;
+	c->scache.sets = scache_size / (c->scache.linesz * c->scache.ways);
+	printk(KERN_INFO "Secondary cache size %dK, linesize %d bytes.\n",
+	       (scache_size >> 10), sc_lsize);
+
+	if (!(config & RM7K_CONF_SE))
+		rm7k_sc_enable();
+
+	bcops = &rm7k_sc_ops;
+
+	/*
+	 * While we're at it let's deal with the tertiary cache.
+	 */
+
+	rm7k_tcache_init = 0;
+	tcache_size = 0;
+
+	if (config & RM7K_CONF_TC)
+		return;
+
+	/*
+	 * No efficient way to ask the hardware for the size of the tcache,
+	 * so must probe for it.
+	 */
+	run_uncached(__probe_tcache);
+	rm7k_tc_enable();
+	rm7k_tcache_init = 1;
+	c->tcache.linesz = tc_lsize;
+	c->tcache.ways = 1;
+	pr_info("Tertiary cache size %ldK.\n", (tcache_size >> 10));
+}
diff --git a/arch/mips/mm/tlb-funcs.S b/arch/mips/mm/tlb-funcs.S
new file mode 100644
index 000000000..00fef578c
--- /dev/null
+++ b/arch/mips/mm/tlb-funcs.S
@@ -0,0 +1,40 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Micro-assembler generated tlb handler functions.
+ *
+ * Copyright (C) 2013  Broadcom Corporation.
+ *
+ * Based on mm/page-funcs.c
+ * Copyright (C) 2012  MIPS Technologies, Inc.
+ * Copyright (C) 2012  Ralf Baechle <ralf@linux-mips.org>
+ */
+#include <asm/asm.h>
+#include <asm/export.h>
+#include <asm/regdef.h>
+
+#define FASTPATH_SIZE	128
+
+LEAF(tlbmiss_handler_setup_pgd)
+1:	j	1b		/* Dummy, will be replaced. */
+	.space	64
+END(tlbmiss_handler_setup_pgd)
+EXPORT(tlbmiss_handler_setup_pgd_end)
+EXPORT_SYMBOL_GPL(tlbmiss_handler_setup_pgd)
+
+LEAF(handle_tlbm)
+	.space		FASTPATH_SIZE * 4
+END(handle_tlbm)
+EXPORT(handle_tlbm_end)
+
+LEAF(handle_tlbs)
+	.space		FASTPATH_SIZE * 4
+END(handle_tlbs)
+EXPORT(handle_tlbs_end)
+
+LEAF(handle_tlbl)
+	.space		FASTPATH_SIZE * 4
+END(handle_tlbl)
+EXPORT(handle_tlbl_end)
diff --git a/arch/mips/mm/tlb-r3k.c b/arch/mips/mm/tlb-r3k.c
new file mode 100644
index 000000000..53dfa2b93
--- /dev/null
+++ b/arch/mips/mm/tlb-r3k.c
@@ -0,0 +1,248 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * r2300.c: R2000 and R3000 specific mmu/cache code.
+ *
+ * Copyright (C) 1996 David S. Miller (davem@davemloft.net)
+ *
+ * with a lot of changes to make this thing work for R3000s
+ * Tx39XX R4k style caches added. HK
+ * Copyright (C) 1998, 1999, 2000 Harald Koerfgen
+ * Copyright (C) 1998 Gleb Raiko & Vladimir Roganov
+ * Copyright (C) 2002  Ralf Baechle
+ * Copyright (C) 2002  Maciej W. Rozycki
+ */
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/smp.h>
+#include <linux/mm.h>
+
+#include <asm/page.h>
+#include <asm/mmu_context.h>
+#include <asm/tlbmisc.h>
+#include <asm/isadep.h>
+#include <asm/io.h>
+#include <asm/bootinfo.h>
+#include <asm/cpu.h>
+
+#undef DEBUG_TLB
+
+extern void build_tlb_refill_handler(void);
+
+/* CP0 hazard avoidance. */
+#define BARRIER				\
+	__asm__ __volatile__(		\
+		".set	push\n\t"	\
+		".set	noreorder\n\t"	\
+		"nop\n\t"		\
+		".set	pop\n\t")
+
+/* TLB operations. */
+static void local_flush_tlb_from(int entry)
+{
+	unsigned long old_ctx;
+
+	old_ctx = read_c0_entryhi() & cpu_asid_mask(&current_cpu_data);
+	write_c0_entrylo0(0);
+	while (entry < current_cpu_data.tlbsize) {
+		write_c0_index(entry << 8);
+		write_c0_entryhi((entry | 0x80000) << 12);
+		entry++;				/* BARRIER */
+		tlb_write_indexed();
+	}
+	write_c0_entryhi(old_ctx);
+}
+
+void local_flush_tlb_all(void)
+{
+	unsigned long flags;
+
+#ifdef DEBUG_TLB
+	printk("[tlball]");
+#endif
+	local_irq_save(flags);
+	local_flush_tlb_from(8);
+	local_irq_restore(flags);
+}
+
+void local_flush_tlb_range(struct vm_area_struct *vma, unsigned long start,
+			   unsigned long end)
+{
+	unsigned long asid_mask = cpu_asid_mask(&current_cpu_data);
+	struct mm_struct *mm = vma->vm_mm;
+	int cpu = smp_processor_id();
+
+	if (cpu_context(cpu, mm) != 0) {
+		unsigned long size, flags;
+
+#ifdef DEBUG_TLB
+		printk("[tlbrange<%lu,0x%08lx,0x%08lx>]",
+			cpu_context(cpu, mm) & asid_mask, start, end);
+#endif
+		local_irq_save(flags);
+		size = (end - start + (PAGE_SIZE - 1)) >> PAGE_SHIFT;
+		if (size <= current_cpu_data.tlbsize) {
+			int oldpid = read_c0_entryhi() & asid_mask;
+			int newpid = cpu_context(cpu, mm) & asid_mask;
+
+			start &= PAGE_MASK;
+			end += PAGE_SIZE - 1;
+			end &= PAGE_MASK;
+			while (start < end) {
+				int idx;
+
+				write_c0_entryhi(start | newpid);
+				start += PAGE_SIZE;	/* BARRIER */
+				tlb_probe();
+				idx = read_c0_index();
+				write_c0_entrylo0(0);
+				write_c0_entryhi(KSEG0);
+				if (idx < 0)		/* BARRIER */
+					continue;
+				tlb_write_indexed();
+			}
+			write_c0_entryhi(oldpid);
+		} else {
+			drop_mmu_context(mm);
+		}
+		local_irq_restore(flags);
+	}
+}
+
+void local_flush_tlb_kernel_range(unsigned long start, unsigned long end)
+{
+	unsigned long size, flags;
+
+#ifdef DEBUG_TLB
+	printk("[tlbrange<%lu,0x%08lx,0x%08lx>]", start, end);
+#endif
+	local_irq_save(flags);
+	size = (end - start + (PAGE_SIZE - 1)) >> PAGE_SHIFT;
+	if (size <= current_cpu_data.tlbsize) {
+		int pid = read_c0_entryhi();
+
+		start &= PAGE_MASK;
+		end += PAGE_SIZE - 1;
+		end &= PAGE_MASK;
+
+		while (start < end) {
+			int idx;
+
+			write_c0_entryhi(start);
+			start += PAGE_SIZE;		/* BARRIER */
+			tlb_probe();
+			idx = read_c0_index();
+			write_c0_entrylo0(0);
+			write_c0_entryhi(KSEG0);
+			if (idx < 0)			/* BARRIER */
+				continue;
+			tlb_write_indexed();
+		}
+		write_c0_entryhi(pid);
+	} else {
+		local_flush_tlb_all();
+	}
+	local_irq_restore(flags);
+}
+
+void local_flush_tlb_page(struct vm_area_struct *vma, unsigned long page)
+{
+	unsigned long asid_mask = cpu_asid_mask(&current_cpu_data);
+	int cpu = smp_processor_id();
+
+	if (cpu_context(cpu, vma->vm_mm) != 0) {
+		unsigned long flags;
+		int oldpid, newpid, idx;
+
+#ifdef DEBUG_TLB
+		printk("[tlbpage<%lu,0x%08lx>]", cpu_context(cpu, vma->vm_mm), page);
+#endif
+		newpid = cpu_context(cpu, vma->vm_mm) & asid_mask;
+		page &= PAGE_MASK;
+		local_irq_save(flags);
+		oldpid = read_c0_entryhi() & asid_mask;
+		write_c0_entryhi(page | newpid);
+		BARRIER;
+		tlb_probe();
+		idx = read_c0_index();
+		write_c0_entrylo0(0);
+		write_c0_entryhi(KSEG0);
+		if (idx < 0)				/* BARRIER */
+			goto finish;
+		tlb_write_indexed();
+
+finish:
+		write_c0_entryhi(oldpid);
+		local_irq_restore(flags);
+	}
+}
+
+void __update_tlb(struct vm_area_struct *vma, unsigned long address, pte_t pte)
+{
+	unsigned long asid_mask = cpu_asid_mask(&current_cpu_data);
+	unsigned long flags;
+	int idx, pid;
+
+	/*
+	 * Handle debugger faulting in for debugee.
+	 */
+	if (current->active_mm != vma->vm_mm)
+		return;
+
+	pid = read_c0_entryhi() & asid_mask;
+
+#ifdef DEBUG_TLB
+	if ((pid != (cpu_context(cpu, vma->vm_mm) & asid_mask)) || (cpu_context(cpu, vma->vm_mm) == 0)) {
+		printk("update_mmu_cache: Wheee, bogus tlbpid mmpid=%lu tlbpid=%d\n",
+		       (cpu_context(cpu, vma->vm_mm)), pid);
+	}
+#endif
+
+	local_irq_save(flags);
+	address &= PAGE_MASK;
+	write_c0_entryhi(address | pid);
+	BARRIER;
+	tlb_probe();
+	idx = read_c0_index();
+	write_c0_entrylo0(pte_val(pte));
+	write_c0_entryhi(address | pid);
+	if (idx < 0) {					/* BARRIER */
+		tlb_write_random();
+	} else {
+		tlb_write_indexed();
+	}
+	write_c0_entryhi(pid);
+	local_irq_restore(flags);
+}
+
+void add_wired_entry(unsigned long entrylo0, unsigned long entrylo1,
+		     unsigned long entryhi, unsigned long pagemask)
+{
+	unsigned long asid_mask = cpu_asid_mask(&current_cpu_data);
+	unsigned long flags;
+	unsigned long old_ctx;
+	static unsigned long wired = 0;
+
+	if (wired < 8) {
+#ifdef DEBUG_TLB
+		printk("[tlbwired<entry lo0 %8x, hi %8x\n>]\n",
+		       entrylo0, entryhi);
+#endif
+
+		local_irq_save(flags);
+		old_ctx = read_c0_entryhi() & asid_mask;
+		write_c0_entrylo0(entrylo0);
+		write_c0_entryhi(entryhi);
+		write_c0_index(wired);
+		wired++;				/* BARRIER */
+		tlb_write_indexed();
+		write_c0_entryhi(old_ctx);
+		local_flush_tlb_all();
+		local_irq_restore(flags);
+	}
+}
+
+void tlb_init(void)
+{
+	local_flush_tlb_from(0);
+	build_tlb_refill_handler();
+}
diff --git a/arch/mips/mm/tlb-r4k.c b/arch/mips/mm/tlb-r4k.c
new file mode 100644
index 000000000..1b939abbe
--- /dev/null
+++ b/arch/mips/mm/tlb-r4k.c
@@ -0,0 +1,583 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1996 David S. Miller (davem@davemloft.net)
+ * Copyright (C) 1997, 1998, 1999, 2000 Ralf Baechle ralf@gnu.org
+ * Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 2002 MIPS Technologies, Inc.  All rights reserved.
+ */
+#include <linux/cpu_pm.h>
+#include <linux/init.h>
+#include <linux/sched.h>
+#include <linux/smp.h>
+#include <linux/mm.h>
+#include <linux/hugetlb.h>
+#include <linux/export.h>
+
+#include <asm/cpu.h>
+#include <asm/cpu-type.h>
+#include <asm/bootinfo.h>
+#include <asm/hazards.h>
+#include <asm/mmu_context.h>
+#include <asm/tlb.h>
+#include <asm/tlbmisc.h>
+
+extern void build_tlb_refill_handler(void);
+
+/*
+ * LOONGSON-2 has a 4 entry itlb which is a subset of jtlb, LOONGSON-3 has
+ * a 4 entry itlb and a 4 entry dtlb which are subsets of jtlb. Unfortunately,
+ * itlb/dtlb are not totally transparent to software.
+ */
+static inline void flush_micro_tlb(void)
+{
+	switch (current_cpu_type()) {
+	case CPU_LOONGSON2EF:
+		write_c0_diag(LOONGSON_DIAG_ITLB);
+		break;
+	case CPU_LOONGSON64:
+		write_c0_diag(LOONGSON_DIAG_ITLB | LOONGSON_DIAG_DTLB);
+		break;
+	default:
+		break;
+	}
+}
+
+static inline void flush_micro_tlb_vm(struct vm_area_struct *vma)
+{
+	if (vma->vm_flags & VM_EXEC)
+		flush_micro_tlb();
+}
+
+void local_flush_tlb_all(void)
+{
+	unsigned long flags;
+	unsigned long old_ctx;
+	int entry, ftlbhighset;
+
+	local_irq_save(flags);
+	/* Save old context and create impossible VPN2 value */
+	old_ctx = read_c0_entryhi();
+	htw_stop();
+	write_c0_entrylo0(0);
+	write_c0_entrylo1(0);
+
+	entry = num_wired_entries();
+
+	/*
+	 * Blast 'em all away.
+	 * If there are any wired entries, fall back to iterating
+	 */
+	if (cpu_has_tlbinv && !entry) {
+		if (current_cpu_data.tlbsizevtlb) {
+			write_c0_index(0);
+			mtc0_tlbw_hazard();
+			tlbinvf();  /* invalidate VTLB */
+		}
+		ftlbhighset = current_cpu_data.tlbsizevtlb +
+			current_cpu_data.tlbsizeftlbsets;
+		for (entry = current_cpu_data.tlbsizevtlb;
+		     entry < ftlbhighset;
+		     entry++) {
+			write_c0_index(entry);
+			mtc0_tlbw_hazard();
+			tlbinvf();  /* invalidate one FTLB set */
+		}
+	} else {
+		while (entry < current_cpu_data.tlbsize) {
+			/* Make sure all entries differ. */
+			write_c0_entryhi(UNIQUE_ENTRYHI(entry));
+			write_c0_index(entry);
+			mtc0_tlbw_hazard();
+			tlb_write_indexed();
+			entry++;
+		}
+	}
+	tlbw_use_hazard();
+	write_c0_entryhi(old_ctx);
+	htw_start();
+	flush_micro_tlb();
+	local_irq_restore(flags);
+}
+EXPORT_SYMBOL(local_flush_tlb_all);
+
+void local_flush_tlb_range(struct vm_area_struct *vma, unsigned long start,
+	unsigned long end)
+{
+	struct mm_struct *mm = vma->vm_mm;
+	int cpu = smp_processor_id();
+
+	if (cpu_context(cpu, mm) != 0) {
+		unsigned long size, flags;
+
+		local_irq_save(flags);
+		start = round_down(start, PAGE_SIZE << 1);
+		end = round_up(end, PAGE_SIZE << 1);
+		size = (end - start) >> (PAGE_SHIFT + 1);
+		if (size <= (current_cpu_data.tlbsizeftlbsets ?
+			     current_cpu_data.tlbsize / 8 :
+			     current_cpu_data.tlbsize / 2)) {
+			unsigned long old_entryhi, old_mmid;
+			int newpid = cpu_asid(cpu, mm);
+
+			old_entryhi = read_c0_entryhi();
+			if (cpu_has_mmid) {
+				old_mmid = read_c0_memorymapid();
+				write_c0_memorymapid(newpid);
+			}
+
+			htw_stop();
+			while (start < end) {
+				int idx;
+
+				if (cpu_has_mmid)
+					write_c0_entryhi(start);
+				else
+					write_c0_entryhi(start | newpid);
+				start += (PAGE_SIZE << 1);
+				mtc0_tlbw_hazard();
+				tlb_probe();
+				tlb_probe_hazard();
+				idx = read_c0_index();
+				write_c0_entrylo0(0);
+				write_c0_entrylo1(0);
+				if (idx < 0)
+					continue;
+				/* Make sure all entries differ. */
+				write_c0_entryhi(UNIQUE_ENTRYHI(idx));
+				mtc0_tlbw_hazard();
+				tlb_write_indexed();
+			}
+			tlbw_use_hazard();
+			write_c0_entryhi(old_entryhi);
+			if (cpu_has_mmid)
+				write_c0_memorymapid(old_mmid);
+			htw_start();
+		} else {
+			drop_mmu_context(mm);
+		}
+		flush_micro_tlb();
+		local_irq_restore(flags);
+	}
+}
+
+void local_flush_tlb_kernel_range(unsigned long start, unsigned long end)
+{
+	unsigned long size, flags;
+
+	local_irq_save(flags);
+	size = (end - start + (PAGE_SIZE - 1)) >> PAGE_SHIFT;
+	size = (size + 1) >> 1;
+	if (size <= (current_cpu_data.tlbsizeftlbsets ?
+		     current_cpu_data.tlbsize / 8 :
+		     current_cpu_data.tlbsize / 2)) {
+		int pid = read_c0_entryhi();
+
+		start &= (PAGE_MASK << 1);
+		end += ((PAGE_SIZE << 1) - 1);
+		end &= (PAGE_MASK << 1);
+		htw_stop();
+
+		while (start < end) {
+			int idx;
+
+			write_c0_entryhi(start);
+			start += (PAGE_SIZE << 1);
+			mtc0_tlbw_hazard();
+			tlb_probe();
+			tlb_probe_hazard();
+			idx = read_c0_index();
+			write_c0_entrylo0(0);
+			write_c0_entrylo1(0);
+			if (idx < 0)
+				continue;
+			/* Make sure all entries differ. */
+			write_c0_entryhi(UNIQUE_ENTRYHI(idx));
+			mtc0_tlbw_hazard();
+			tlb_write_indexed();
+		}
+		tlbw_use_hazard();
+		write_c0_entryhi(pid);
+		htw_start();
+	} else {
+		local_flush_tlb_all();
+	}
+	flush_micro_tlb();
+	local_irq_restore(flags);
+}
+
+void local_flush_tlb_page(struct vm_area_struct *vma, unsigned long page)
+{
+	int cpu = smp_processor_id();
+
+	if (cpu_context(cpu, vma->vm_mm) != 0) {
+		unsigned long old_mmid;
+		unsigned long flags, old_entryhi;
+		int idx;
+
+		page &= (PAGE_MASK << 1);
+		local_irq_save(flags);
+		old_entryhi = read_c0_entryhi();
+		htw_stop();
+		if (cpu_has_mmid) {
+			old_mmid = read_c0_memorymapid();
+			write_c0_entryhi(page);
+			write_c0_memorymapid(cpu_asid(cpu, vma->vm_mm));
+		} else {
+			write_c0_entryhi(page | cpu_asid(cpu, vma->vm_mm));
+		}
+		mtc0_tlbw_hazard();
+		tlb_probe();
+		tlb_probe_hazard();
+		idx = read_c0_index();
+		write_c0_entrylo0(0);
+		write_c0_entrylo1(0);
+		if (idx < 0)
+			goto finish;
+		/* Make sure all entries differ. */
+		write_c0_entryhi(UNIQUE_ENTRYHI(idx));
+		mtc0_tlbw_hazard();
+		tlb_write_indexed();
+		tlbw_use_hazard();
+
+	finish:
+		write_c0_entryhi(old_entryhi);
+		if (cpu_has_mmid)
+			write_c0_memorymapid(old_mmid);
+		htw_start();
+		flush_micro_tlb_vm(vma);
+		local_irq_restore(flags);
+	}
+}
+
+/*
+ * This one is only used for pages with the global bit set so we don't care
+ * much about the ASID.
+ */
+void local_flush_tlb_one(unsigned long page)
+{
+	unsigned long flags;
+	int oldpid, idx;
+
+	local_irq_save(flags);
+	oldpid = read_c0_entryhi();
+	htw_stop();
+	page &= (PAGE_MASK << 1);
+	write_c0_entryhi(page);
+	mtc0_tlbw_hazard();
+	tlb_probe();
+	tlb_probe_hazard();
+	idx = read_c0_index();
+	write_c0_entrylo0(0);
+	write_c0_entrylo1(0);
+	if (idx >= 0) {
+		/* Make sure all entries differ. */
+		write_c0_entryhi(UNIQUE_ENTRYHI(idx));
+		mtc0_tlbw_hazard();
+		tlb_write_indexed();
+		tlbw_use_hazard();
+	}
+	write_c0_entryhi(oldpid);
+	htw_start();
+	flush_micro_tlb();
+	local_irq_restore(flags);
+}
+
+/*
+ * We will need multiple versions of update_mmu_cache(), one that just
+ * updates the TLB with the new pte(s), and another which also checks
+ * for the R4k "end of page" hardware bug and does the needy.
+ */
+void __update_tlb(struct vm_area_struct * vma, unsigned long address, pte_t pte)
+{
+	unsigned long flags;
+	pgd_t *pgdp;
+	p4d_t *p4dp;
+	pud_t *pudp;
+	pmd_t *pmdp;
+	pte_t *ptep;
+	int idx, pid;
+
+	/*
+	 * Handle debugger faulting in for debugee.
+	 */
+	if (current->active_mm != vma->vm_mm)
+		return;
+
+	local_irq_save(flags);
+
+	htw_stop();
+	address &= (PAGE_MASK << 1);
+	if (cpu_has_mmid) {
+		write_c0_entryhi(address);
+	} else {
+		pid = read_c0_entryhi() & cpu_asid_mask(&current_cpu_data);
+		write_c0_entryhi(address | pid);
+	}
+	pgdp = pgd_offset(vma->vm_mm, address);
+	mtc0_tlbw_hazard();
+	tlb_probe();
+	tlb_probe_hazard();
+	p4dp = p4d_offset(pgdp, address);
+	pudp = pud_offset(p4dp, address);
+	pmdp = pmd_offset(pudp, address);
+	idx = read_c0_index();
+#ifdef CONFIG_MIPS_HUGE_TLB_SUPPORT
+	/* this could be a huge page  */
+	if (pmd_huge(*pmdp)) {
+		unsigned long lo;
+		write_c0_pagemask(PM_HUGE_MASK);
+		ptep = (pte_t *)pmdp;
+		lo = pte_to_entrylo(pte_val(*ptep));
+		write_c0_entrylo0(lo);
+		write_c0_entrylo1(lo + (HPAGE_SIZE >> 7));
+
+		mtc0_tlbw_hazard();
+		if (idx < 0)
+			tlb_write_random();
+		else
+			tlb_write_indexed();
+		tlbw_use_hazard();
+		write_c0_pagemask(PM_DEFAULT_MASK);
+	} else
+#endif
+	{
+		ptep = pte_offset_map(pmdp, address);
+
+#if defined(CONFIG_PHYS_ADDR_T_64BIT) && defined(CONFIG_CPU_MIPS32)
+#ifdef CONFIG_XPA
+		write_c0_entrylo0(pte_to_entrylo(ptep->pte_high));
+		if (cpu_has_xpa)
+			writex_c0_entrylo0(ptep->pte_low & _PFNX_MASK);
+		ptep++;
+		write_c0_entrylo1(pte_to_entrylo(ptep->pte_high));
+		if (cpu_has_xpa)
+			writex_c0_entrylo1(ptep->pte_low & _PFNX_MASK);
+#else
+		write_c0_entrylo0(ptep->pte_high);
+		ptep++;
+		write_c0_entrylo1(ptep->pte_high);
+#endif
+#else
+		write_c0_entrylo0(pte_to_entrylo(pte_val(*ptep++)));
+		write_c0_entrylo1(pte_to_entrylo(pte_val(*ptep)));
+#endif
+		mtc0_tlbw_hazard();
+		if (idx < 0)
+			tlb_write_random();
+		else
+			tlb_write_indexed();
+	}
+	tlbw_use_hazard();
+	htw_start();
+	flush_micro_tlb_vm(vma);
+	local_irq_restore(flags);
+}
+
+void add_wired_entry(unsigned long entrylo0, unsigned long entrylo1,
+		     unsigned long entryhi, unsigned long pagemask)
+{
+#ifdef CONFIG_XPA
+	panic("Broken for XPA kernels");
+#else
+	unsigned int old_mmid;
+	unsigned long flags;
+	unsigned long wired;
+	unsigned long old_pagemask;
+	unsigned long old_ctx;
+
+	local_irq_save(flags);
+	if (cpu_has_mmid) {
+		old_mmid = read_c0_memorymapid();
+		write_c0_memorymapid(MMID_KERNEL_WIRED);
+	}
+	/* Save old context and create impossible VPN2 value */
+	old_ctx = read_c0_entryhi();
+	htw_stop();
+	old_pagemask = read_c0_pagemask();
+	wired = num_wired_entries();
+	write_c0_wired(wired + 1);
+	write_c0_index(wired);
+	tlbw_use_hazard();	/* What is the hazard here? */
+	write_c0_pagemask(pagemask);
+	write_c0_entryhi(entryhi);
+	write_c0_entrylo0(entrylo0);
+	write_c0_entrylo1(entrylo1);
+	mtc0_tlbw_hazard();
+	tlb_write_indexed();
+	tlbw_use_hazard();
+
+	write_c0_entryhi(old_ctx);
+	if (cpu_has_mmid)
+		write_c0_memorymapid(old_mmid);
+	tlbw_use_hazard();	/* What is the hazard here? */
+	htw_start();
+	write_c0_pagemask(old_pagemask);
+	local_flush_tlb_all();
+	local_irq_restore(flags);
+#endif
+}
+
+#ifdef CONFIG_TRANSPARENT_HUGEPAGE
+
+int has_transparent_hugepage(void)
+{
+	static unsigned int mask = -1;
+
+	if (mask == -1) {	/* first call comes during __init */
+		unsigned long flags;
+
+		local_irq_save(flags);
+		write_c0_pagemask(PM_HUGE_MASK);
+		back_to_back_c0_hazard();
+		mask = read_c0_pagemask();
+		write_c0_pagemask(PM_DEFAULT_MASK);
+		local_irq_restore(flags);
+	}
+	return mask == PM_HUGE_MASK;
+}
+EXPORT_SYMBOL(has_transparent_hugepage);
+
+#endif /* CONFIG_TRANSPARENT_HUGEPAGE  */
+
+/*
+ * Used for loading TLB entries before trap_init() has started, when we
+ * don't actually want to add a wired entry which remains throughout the
+ * lifetime of the system
+ */
+
+int temp_tlb_entry;
+
+__init int add_temporary_entry(unsigned long entrylo0, unsigned long entrylo1,
+			       unsigned long entryhi, unsigned long pagemask)
+{
+	int ret = 0;
+	unsigned long flags;
+	unsigned long wired;
+	unsigned long old_pagemask;
+	unsigned long old_ctx;
+
+	local_irq_save(flags);
+	/* Save old context and create impossible VPN2 value */
+	htw_stop();
+	old_ctx = read_c0_entryhi();
+	old_pagemask = read_c0_pagemask();
+	wired = num_wired_entries();
+	if (--temp_tlb_entry < wired) {
+		printk(KERN_WARNING
+		       "No TLB space left for add_temporary_entry\n");
+		ret = -ENOSPC;
+		goto out;
+	}
+
+	write_c0_index(temp_tlb_entry);
+	write_c0_pagemask(pagemask);
+	write_c0_entryhi(entryhi);
+	write_c0_entrylo0(entrylo0);
+	write_c0_entrylo1(entrylo1);
+	mtc0_tlbw_hazard();
+	tlb_write_indexed();
+	tlbw_use_hazard();
+
+	write_c0_entryhi(old_ctx);
+	write_c0_pagemask(old_pagemask);
+	htw_start();
+out:
+	local_irq_restore(flags);
+	return ret;
+}
+
+static int ntlb;
+static int __init set_ntlb(char *str)
+{
+	get_option(&str, &ntlb);
+	return 1;
+}
+
+__setup("ntlb=", set_ntlb);
+
+/*
+ * Configure TLB (for init or after a CPU has been powered off).
+ */
+static void r4k_tlb_configure(void)
+{
+	/*
+	 * You should never change this register:
+	 *   - On R4600 1.7 the tlbp never hits for pages smaller than
+	 *     the value in the c0_pagemask register.
+	 *   - The entire mm handling assumes the c0_pagemask register to
+	 *     be set to fixed-size pages.
+	 */
+	write_c0_pagemask(PM_DEFAULT_MASK);
+	back_to_back_c0_hazard();
+	if (read_c0_pagemask() != PM_DEFAULT_MASK)
+		panic("MMU doesn't support PAGE_SIZE=0x%lx", PAGE_SIZE);
+
+	write_c0_wired(0);
+	if (current_cpu_type() == CPU_R10000 ||
+	    current_cpu_type() == CPU_R12000 ||
+	    current_cpu_type() == CPU_R14000 ||
+	    current_cpu_type() == CPU_R16000)
+		write_c0_framemask(0);
+
+	if (cpu_has_rixi) {
+		/*
+		 * Enable the no read, no exec bits, and enable large physical
+		 * address.
+		 */
+#ifdef CONFIG_64BIT
+		set_c0_pagegrain(PG_RIE | PG_XIE | PG_ELPA);
+#else
+		set_c0_pagegrain(PG_RIE | PG_XIE);
+#endif
+	}
+
+	temp_tlb_entry = current_cpu_data.tlbsize - 1;
+
+	/* From this point on the ARC firmware is dead.	 */
+	local_flush_tlb_all();
+
+	/* Did I tell you that ARC SUCKS?  */
+}
+
+void tlb_init(void)
+{
+	r4k_tlb_configure();
+
+	if (ntlb) {
+		if (ntlb > 1 && ntlb <= current_cpu_data.tlbsize) {
+			int wired = current_cpu_data.tlbsize - ntlb;
+			write_c0_wired(wired);
+			write_c0_index(wired-1);
+			printk("Restricting TLB to %d entries\n", ntlb);
+		} else
+			printk("Ignoring invalid argument ntlb=%d\n", ntlb);
+	}
+
+	build_tlb_refill_handler();
+}
+
+static int r4k_tlb_pm_notifier(struct notifier_block *self, unsigned long cmd,
+			       void *v)
+{
+	switch (cmd) {
+	case CPU_PM_ENTER_FAILED:
+	case CPU_PM_EXIT:
+		r4k_tlb_configure();
+		break;
+	}
+
+	return NOTIFY_OK;
+}
+
+static struct notifier_block r4k_tlb_pm_notifier_block = {
+	.notifier_call = r4k_tlb_pm_notifier,
+};
+
+static int __init r4k_tlb_init_pm(void)
+{
+	return cpu_pm_register_notifier(&r4k_tlb_pm_notifier_block);
+}
+arch_initcall(r4k_tlb_init_pm);
diff --git a/arch/mips/mm/tlbex-fault.S b/arch/mips/mm/tlbex-fault.S
new file mode 100644
index 000000000..77db401fc
--- /dev/null
+++ b/arch/mips/mm/tlbex-fault.S
@@ -0,0 +1,28 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1999 Ralf Baechle
+ * Copyright (C) 1999 Silicon Graphics, Inc.
+ */
+#include <asm/mipsregs.h>
+#include <asm/regdef.h>
+#include <asm/stackframe.h>
+
+	.macro tlb_do_page_fault, write
+	NESTED(tlb_do_page_fault_\write, PT_SIZE, sp)
+	.cfi_signal_frame
+	SAVE_ALL docfi=1
+	MFC0	a2, CP0_BADVADDR
+	KMODE
+	move	a0, sp
+	REG_S	a2, PT_BVADDR(sp)
+	li	a1, \write
+	jal	do_page_fault
+	j	ret_from_exception
+	END(tlb_do_page_fault_\write)
+	.endm
+
+	tlb_do_page_fault 0
+	tlb_do_page_fault 1
diff --git a/arch/mips/mm/tlbex.c b/arch/mips/mm/tlbex.c
new file mode 100644
index 000000000..80e05ee98
--- /dev/null
+++ b/arch/mips/mm/tlbex.c
@@ -0,0 +1,2619 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Synthesize TLB refill handlers at runtime.
+ *
+ * Copyright (C) 2004, 2005, 2006, 2008	 Thiemo Seufer
+ * Copyright (C) 2005, 2007, 2008, 2009	 Maciej W. Rozycki
+ * Copyright (C) 2006  Ralf Baechle (ralf@linux-mips.org)
+ * Copyright (C) 2008, 2009 Cavium Networks, Inc.
+ * Copyright (C) 2011  MIPS Technologies, Inc.
+ *
+ * ... and the days got worse and worse and now you see
+ * I've gone completely out of my mind.
+ *
+ * They're coming to take me a away haha
+ * they're coming to take me a away hoho hihi haha
+ * to the funny farm where code is beautiful all the time ...
+ *
+ * (Condolences to Napoleon XIV)
+ */
+
+#include <linux/bug.h>
+#include <linux/export.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/smp.h>
+#include <linux/string.h>
+#include <linux/cache.h>
+#include <linux/pgtable.h>
+
+#include <asm/cacheflush.h>
+#include <asm/cpu-type.h>
+#include <asm/mmu_context.h>
+#include <asm/uasm.h>
+#include <asm/setup.h>
+#include <asm/tlbex.h>
+
+static int mips_xpa_disabled;
+
+static int __init xpa_disable(char *s)
+{
+	mips_xpa_disabled = 1;
+
+	return 1;
+}
+
+__setup("noxpa", xpa_disable);
+
+/*
+ * TLB load/store/modify handlers.
+ *
+ * Only the fastpath gets synthesized at runtime, the slowpath for
+ * do_page_fault remains normal asm.
+ */
+extern void tlb_do_page_fault_0(void);
+extern void tlb_do_page_fault_1(void);
+
+struct work_registers {
+	int r1;
+	int r2;
+	int r3;
+};
+
+struct tlb_reg_save {
+	unsigned long a;
+	unsigned long b;
+} ____cacheline_aligned_in_smp;
+
+static struct tlb_reg_save handler_reg_save[NR_CPUS];
+
+static inline int r45k_bvahwbug(void)
+{
+	/* XXX: We should probe for the presence of this bug, but we don't. */
+	return 0;
+}
+
+static inline int r4k_250MHZhwbug(void)
+{
+	/* XXX: We should probe for the presence of this bug, but we don't. */
+	return 0;
+}
+
+extern int sb1250_m3_workaround_needed(void);
+
+static inline int __maybe_unused bcm1250_m3_war(void)
+{
+	if (IS_ENABLED(CONFIG_SB1_PASS_2_WORKAROUNDS))
+		return sb1250_m3_workaround_needed();
+	return 0;
+}
+
+static inline int __maybe_unused r10000_llsc_war(void)
+{
+	return IS_ENABLED(CONFIG_WAR_R10000_LLSC);
+}
+
+static int use_bbit_insns(void)
+{
+	switch (current_cpu_type()) {
+	case CPU_CAVIUM_OCTEON:
+	case CPU_CAVIUM_OCTEON_PLUS:
+	case CPU_CAVIUM_OCTEON2:
+	case CPU_CAVIUM_OCTEON3:
+		return 1;
+	default:
+		return 0;
+	}
+}
+
+static int use_lwx_insns(void)
+{
+	switch (current_cpu_type()) {
+	case CPU_CAVIUM_OCTEON2:
+	case CPU_CAVIUM_OCTEON3:
+		return 1;
+	default:
+		return 0;
+	}
+}
+#if defined(CONFIG_CAVIUM_OCTEON_CVMSEG_SIZE) && \
+    CONFIG_CAVIUM_OCTEON_CVMSEG_SIZE > 0
+static bool scratchpad_available(void)
+{
+	return true;
+}
+static int scratchpad_offset(int i)
+{
+	/*
+	 * CVMSEG starts at address -32768 and extends for
+	 * CAVIUM_OCTEON_CVMSEG_SIZE 128 byte cache lines.
+	 */
+	i += 1; /* Kernel use starts at the top and works down. */
+	return CONFIG_CAVIUM_OCTEON_CVMSEG_SIZE * 128 - (8 * i) - 32768;
+}
+#else
+static bool scratchpad_available(void)
+{
+	return false;
+}
+static int scratchpad_offset(int i)
+{
+	BUG();
+	/* Really unreachable, but evidently some GCC want this. */
+	return 0;
+}
+#endif
+/*
+ * Found by experiment: At least some revisions of the 4kc throw under
+ * some circumstances a machine check exception, triggered by invalid
+ * values in the index register.  Delaying the tlbp instruction until
+ * after the next branch,  plus adding an additional nop in front of
+ * tlbwi/tlbwr avoids the invalid index register values. Nobody knows
+ * why; it's not an issue caused by the core RTL.
+ *
+ */
+static int m4kc_tlbp_war(void)
+{
+	return current_cpu_type() == CPU_4KC;
+}
+
+/* Handle labels (which must be positive integers). */
+enum label_id {
+	label_second_part = 1,
+	label_leave,
+	label_vmalloc,
+	label_vmalloc_done,
+	label_tlbw_hazard_0,
+	label_split = label_tlbw_hazard_0 + 8,
+	label_tlbl_goaround1,
+	label_tlbl_goaround2,
+	label_nopage_tlbl,
+	label_nopage_tlbs,
+	label_nopage_tlbm,
+	label_smp_pgtable_change,
+	label_r3000_write_probe_fail,
+	label_large_segbits_fault,
+#ifdef CONFIG_MIPS_HUGE_TLB_SUPPORT
+	label_tlb_huge_update,
+#endif
+};
+
+UASM_L_LA(_second_part)
+UASM_L_LA(_leave)
+UASM_L_LA(_vmalloc)
+UASM_L_LA(_vmalloc_done)
+/* _tlbw_hazard_x is handled differently.  */
+UASM_L_LA(_split)
+UASM_L_LA(_tlbl_goaround1)
+UASM_L_LA(_tlbl_goaround2)
+UASM_L_LA(_nopage_tlbl)
+UASM_L_LA(_nopage_tlbs)
+UASM_L_LA(_nopage_tlbm)
+UASM_L_LA(_smp_pgtable_change)
+UASM_L_LA(_r3000_write_probe_fail)
+UASM_L_LA(_large_segbits_fault)
+#ifdef CONFIG_MIPS_HUGE_TLB_SUPPORT
+UASM_L_LA(_tlb_huge_update)
+#endif
+
+static int hazard_instance;
+
+static void uasm_bgezl_hazard(u32 **p, struct uasm_reloc **r, int instance)
+{
+	switch (instance) {
+	case 0 ... 7:
+		uasm_il_bgezl(p, r, 0, label_tlbw_hazard_0 + instance);
+		return;
+	default:
+		BUG();
+	}
+}
+
+static void uasm_bgezl_label(struct uasm_label **l, u32 **p, int instance)
+{
+	switch (instance) {
+	case 0 ... 7:
+		uasm_build_label(l, *p, label_tlbw_hazard_0 + instance);
+		break;
+	default:
+		BUG();
+	}
+}
+
+/*
+ * pgtable bits are assigned dynamically depending on processor feature
+ * and statically based on kernel configuration.  This spits out the actual
+ * values the kernel is using.	Required to make sense from disassembled
+ * TLB exception handlers.
+ */
+static void output_pgtable_bits_defines(void)
+{
+#define pr_define(fmt, ...)					\
+	pr_debug("#define " fmt, ##__VA_ARGS__)
+
+	pr_debug("#include <asm/asm.h>\n");
+	pr_debug("#include <asm/regdef.h>\n");
+	pr_debug("\n");
+
+	pr_define("_PAGE_PRESENT_SHIFT %d\n", _PAGE_PRESENT_SHIFT);
+	pr_define("_PAGE_NO_READ_SHIFT %d\n", _PAGE_NO_READ_SHIFT);
+	pr_define("_PAGE_WRITE_SHIFT %d\n", _PAGE_WRITE_SHIFT);
+	pr_define("_PAGE_ACCESSED_SHIFT %d\n", _PAGE_ACCESSED_SHIFT);
+	pr_define("_PAGE_MODIFIED_SHIFT %d\n", _PAGE_MODIFIED_SHIFT);
+#ifdef CONFIG_MIPS_HUGE_TLB_SUPPORT
+	pr_define("_PAGE_HUGE_SHIFT %d\n", _PAGE_HUGE_SHIFT);
+#endif
+#ifdef _PAGE_NO_EXEC_SHIFT
+	if (cpu_has_rixi)
+		pr_define("_PAGE_NO_EXEC_SHIFT %d\n", _PAGE_NO_EXEC_SHIFT);
+#endif
+	pr_define("_PAGE_GLOBAL_SHIFT %d\n", _PAGE_GLOBAL_SHIFT);
+	pr_define("_PAGE_VALID_SHIFT %d\n", _PAGE_VALID_SHIFT);
+	pr_define("_PAGE_DIRTY_SHIFT %d\n", _PAGE_DIRTY_SHIFT);
+	pr_define("_PFN_SHIFT %d\n", _PFN_SHIFT);
+	pr_debug("\n");
+}
+
+static inline void dump_handler(const char *symbol, const void *start, const void *end)
+{
+	unsigned int count = (end - start) / sizeof(u32);
+	const u32 *handler = start;
+	int i;
+
+	pr_debug("LEAF(%s)\n", symbol);
+
+	pr_debug("\t.set push\n");
+	pr_debug("\t.set noreorder\n");
+
+	for (i = 0; i < count; i++)
+		pr_debug("\t.word\t0x%08x\t\t# %p\n", handler[i], &handler[i]);
+
+	pr_debug("\t.set\tpop\n");
+
+	pr_debug("\tEND(%s)\n", symbol);
+}
+
+/* The only general purpose registers allowed in TLB handlers. */
+#define K0		26
+#define K1		27
+
+/* Some CP0 registers */
+#define C0_INDEX	0, 0
+#define C0_ENTRYLO0	2, 0
+#define C0_TCBIND	2, 2
+#define C0_ENTRYLO1	3, 0
+#define C0_CONTEXT	4, 0
+#define C0_PAGEMASK	5, 0
+#define C0_PWBASE	5, 5
+#define C0_PWFIELD	5, 6
+#define C0_PWSIZE	5, 7
+#define C0_PWCTL	6, 6
+#define C0_BADVADDR	8, 0
+#define C0_PGD		9, 7
+#define C0_ENTRYHI	10, 0
+#define C0_EPC		14, 0
+#define C0_XCONTEXT	20, 0
+
+#ifdef CONFIG_64BIT
+# define GET_CONTEXT(buf, reg) UASM_i_MFC0(buf, reg, C0_XCONTEXT)
+#else
+# define GET_CONTEXT(buf, reg) UASM_i_MFC0(buf, reg, C0_CONTEXT)
+#endif
+
+/* The worst case length of the handler is around 18 instructions for
+ * R3000-style TLBs and up to 63 instructions for R4000-style TLBs.
+ * Maximum space available is 32 instructions for R3000 and 64
+ * instructions for R4000.
+ *
+ * We deliberately chose a buffer size of 128, so we won't scribble
+ * over anything important on overflow before we panic.
+ */
+static u32 tlb_handler[128];
+
+/* simply assume worst case size for labels and relocs */
+static struct uasm_label labels[128];
+static struct uasm_reloc relocs[128];
+
+static int check_for_high_segbits;
+static bool fill_includes_sw_bits;
+
+static unsigned int kscratch_used_mask;
+
+static inline int __maybe_unused c0_kscratch(void)
+{
+	return 31;
+}
+
+static int allocate_kscratch(void)
+{
+	int r;
+	unsigned int a = cpu_data[0].kscratch_mask & ~kscratch_used_mask;
+
+	r = ffs(a);
+
+	if (r == 0)
+		return -1;
+
+	r--; /* make it zero based */
+
+	kscratch_used_mask |= (1 << r);
+
+	return r;
+}
+
+static int scratch_reg;
+int pgd_reg;
+EXPORT_SYMBOL_GPL(pgd_reg);
+enum vmalloc64_mode {not_refill, refill_scratch, refill_noscratch};
+
+static struct work_registers build_get_work_registers(u32 **p)
+{
+	struct work_registers r;
+
+	if (scratch_reg >= 0) {
+		/* Save in CPU local C0_KScratch? */
+		UASM_i_MTC0(p, 1, c0_kscratch(), scratch_reg);
+		r.r1 = K0;
+		r.r2 = K1;
+		r.r3 = 1;
+		return r;
+	}
+
+	if (num_possible_cpus() > 1) {
+		/* Get smp_processor_id */
+		UASM_i_CPUID_MFC0(p, K0, SMP_CPUID_REG);
+		UASM_i_SRL_SAFE(p, K0, K0, SMP_CPUID_REGSHIFT);
+
+		/* handler_reg_save index in K0 */
+		UASM_i_SLL(p, K0, K0, ilog2(sizeof(struct tlb_reg_save)));
+
+		UASM_i_LA(p, K1, (long)&handler_reg_save);
+		UASM_i_ADDU(p, K0, K0, K1);
+	} else {
+		UASM_i_LA(p, K0, (long)&handler_reg_save);
+	}
+	/* K0 now points to save area, save $1 and $2  */
+	UASM_i_SW(p, 1, offsetof(struct tlb_reg_save, a), K0);
+	UASM_i_SW(p, 2, offsetof(struct tlb_reg_save, b), K0);
+
+	r.r1 = K1;
+	r.r2 = 1;
+	r.r3 = 2;
+	return r;
+}
+
+static void build_restore_work_registers(u32 **p)
+{
+	if (scratch_reg >= 0) {
+		uasm_i_ehb(p);
+		UASM_i_MFC0(p, 1, c0_kscratch(), scratch_reg);
+		return;
+	}
+	/* K0 already points to save area, restore $1 and $2  */
+	UASM_i_LW(p, 1, offsetof(struct tlb_reg_save, a), K0);
+	UASM_i_LW(p, 2, offsetof(struct tlb_reg_save, b), K0);
+}
+
+#ifndef CONFIG_MIPS_PGD_C0_CONTEXT
+
+/*
+ * CONFIG_MIPS_PGD_C0_CONTEXT implies 64 bit and lack of pgd_current,
+ * we cannot do r3000 under these circumstances.
+ *
+ * The R3000 TLB handler is simple.
+ */
+static void build_r3000_tlb_refill_handler(void)
+{
+	long pgdc = (long)pgd_current;
+	u32 *p;
+
+	memset(tlb_handler, 0, sizeof(tlb_handler));
+	p = tlb_handler;
+
+	uasm_i_mfc0(&p, K0, C0_BADVADDR);
+	uasm_i_lui(&p, K1, uasm_rel_hi(pgdc)); /* cp0 delay */
+	uasm_i_lw(&p, K1, uasm_rel_lo(pgdc), K1);
+	uasm_i_srl(&p, K0, K0, 22); /* load delay */
+	uasm_i_sll(&p, K0, K0, 2);
+	uasm_i_addu(&p, K1, K1, K0);
+	uasm_i_mfc0(&p, K0, C0_CONTEXT);
+	uasm_i_lw(&p, K1, 0, K1); /* cp0 delay */
+	uasm_i_andi(&p, K0, K0, 0xffc); /* load delay */
+	uasm_i_addu(&p, K1, K1, K0);
+	uasm_i_lw(&p, K0, 0, K1);
+	uasm_i_nop(&p); /* load delay */
+	uasm_i_mtc0(&p, K0, C0_ENTRYLO0);
+	uasm_i_mfc0(&p, K1, C0_EPC); /* cp0 delay */
+	uasm_i_tlbwr(&p); /* cp0 delay */
+	uasm_i_jr(&p, K1);
+	uasm_i_rfe(&p); /* branch delay */
+
+	if (p > tlb_handler + 32)
+		panic("TLB refill handler space exceeded");
+
+	pr_debug("Wrote TLB refill handler (%u instructions).\n",
+		 (unsigned int)(p - tlb_handler));
+
+	memcpy((void *)ebase, tlb_handler, 0x80);
+	local_flush_icache_range(ebase, ebase + 0x80);
+	dump_handler("r3000_tlb_refill", (u32 *)ebase, (u32 *)(ebase + 0x80));
+}
+#endif /* CONFIG_MIPS_PGD_C0_CONTEXT */
+
+/*
+ * The R4000 TLB handler is much more complicated. We have two
+ * consecutive handler areas with 32 instructions space each.
+ * Since they aren't used at the same time, we can overflow in the
+ * other one.To keep things simple, we first assume linear space,
+ * then we relocate it to the final handler layout as needed.
+ */
+static u32 final_handler[64];
+
+/*
+ * Hazards
+ *
+ * From the IDT errata for the QED RM5230 (Nevada), processor revision 1.0:
+ * 2. A timing hazard exists for the TLBP instruction.
+ *
+ *	stalling_instruction
+ *	TLBP
+ *
+ * The JTLB is being read for the TLBP throughout the stall generated by the
+ * previous instruction. This is not really correct as the stalling instruction
+ * can modify the address used to access the JTLB.  The failure symptom is that
+ * the TLBP instruction will use an address created for the stalling instruction
+ * and not the address held in C0_ENHI and thus report the wrong results.
+ *
+ * The software work-around is to not allow the instruction preceding the TLBP
+ * to stall - make it an NOP or some other instruction guaranteed not to stall.
+ *
+ * Errata 2 will not be fixed.	This errata is also on the R5000.
+ *
+ * As if we MIPS hackers wouldn't know how to nop pipelines happy ...
+ */
+static void __maybe_unused build_tlb_probe_entry(u32 **p)
+{
+	switch (current_cpu_type()) {
+	/* Found by experiment: R4600 v2.0/R4700 needs this, too.  */
+	case CPU_R4600:
+	case CPU_R4700:
+	case CPU_R5000:
+	case CPU_NEVADA:
+		uasm_i_nop(p);
+		uasm_i_tlbp(p);
+		break;
+
+	default:
+		uasm_i_tlbp(p);
+		break;
+	}
+}
+
+void build_tlb_write_entry(u32 **p, struct uasm_label **l,
+			   struct uasm_reloc **r,
+			   enum tlb_write_entry wmode)
+{
+	void(*tlbw)(u32 **) = NULL;
+
+	switch (wmode) {
+	case tlb_random: tlbw = uasm_i_tlbwr; break;
+	case tlb_indexed: tlbw = uasm_i_tlbwi; break;
+	}
+
+	if (cpu_has_mips_r2_r6) {
+		if (cpu_has_mips_r2_exec_hazard)
+			uasm_i_ehb(p);
+		tlbw(p);
+		return;
+	}
+
+	switch (current_cpu_type()) {
+	case CPU_R4000PC:
+	case CPU_R4000SC:
+	case CPU_R4000MC:
+	case CPU_R4400PC:
+	case CPU_R4400SC:
+	case CPU_R4400MC:
+		/*
+		 * This branch uses up a mtc0 hazard nop slot and saves
+		 * two nops after the tlbw instruction.
+		 */
+		uasm_bgezl_hazard(p, r, hazard_instance);
+		tlbw(p);
+		uasm_bgezl_label(l, p, hazard_instance);
+		hazard_instance++;
+		uasm_i_nop(p);
+		break;
+
+	case CPU_R4600:
+	case CPU_R4700:
+		uasm_i_nop(p);
+		tlbw(p);
+		uasm_i_nop(p);
+		break;
+
+	case CPU_R5000:
+	case CPU_NEVADA:
+		uasm_i_nop(p); /* QED specifies 2 nops hazard */
+		uasm_i_nop(p); /* QED specifies 2 nops hazard */
+		tlbw(p);
+		break;
+
+	case CPU_R4300:
+	case CPU_5KC:
+	case CPU_TX49XX:
+	case CPU_PR4450:
+		uasm_i_nop(p);
+		tlbw(p);
+		break;
+
+	case CPU_R10000:
+	case CPU_R12000:
+	case CPU_R14000:
+	case CPU_R16000:
+	case CPU_4KC:
+	case CPU_4KEC:
+	case CPU_M14KC:
+	case CPU_M14KEC:
+	case CPU_SB1:
+	case CPU_SB1A:
+	case CPU_4KSC:
+	case CPU_20KC:
+	case CPU_25KF:
+	case CPU_BMIPS32:
+	case CPU_BMIPS3300:
+	case CPU_BMIPS4350:
+	case CPU_BMIPS4380:
+	case CPU_BMIPS5000:
+	case CPU_LOONGSON2EF:
+	case CPU_LOONGSON64:
+	case CPU_R5500:
+		if (m4kc_tlbp_war())
+			uasm_i_nop(p);
+		fallthrough;
+	case CPU_ALCHEMY:
+		tlbw(p);
+		break;
+
+	case CPU_RM7000:
+		uasm_i_nop(p);
+		uasm_i_nop(p);
+		uasm_i_nop(p);
+		uasm_i_nop(p);
+		tlbw(p);
+		break;
+
+	case CPU_XBURST:
+		tlbw(p);
+		uasm_i_nop(p);
+		break;
+
+	default:
+		panic("No TLB refill handler yet (CPU type: %d)",
+		      current_cpu_type());
+		break;
+	}
+}
+EXPORT_SYMBOL_GPL(build_tlb_write_entry);
+
+static __maybe_unused void build_convert_pte_to_entrylo(u32 **p,
+							unsigned int reg)
+{
+	if (_PAGE_GLOBAL_SHIFT == 0) {
+		/* pte_t is already in EntryLo format */
+		return;
+	}
+
+	if (cpu_has_rixi && _PAGE_NO_EXEC != 0) {
+		if (fill_includes_sw_bits) {
+			UASM_i_ROTR(p, reg, reg, ilog2(_PAGE_GLOBAL));
+		} else {
+			UASM_i_SRL(p, reg, reg, ilog2(_PAGE_NO_EXEC));
+			UASM_i_ROTR(p, reg, reg,
+				    ilog2(_PAGE_GLOBAL) - ilog2(_PAGE_NO_EXEC));
+		}
+	} else {
+#ifdef CONFIG_PHYS_ADDR_T_64BIT
+		uasm_i_dsrl_safe(p, reg, reg, ilog2(_PAGE_GLOBAL));
+#else
+		UASM_i_SRL(p, reg, reg, ilog2(_PAGE_GLOBAL));
+#endif
+	}
+}
+
+#ifdef CONFIG_MIPS_HUGE_TLB_SUPPORT
+
+static void build_restore_pagemask(u32 **p, struct uasm_reloc **r,
+				   unsigned int tmp, enum label_id lid,
+				   int restore_scratch)
+{
+	if (restore_scratch) {
+		/*
+		 * Ensure the MFC0 below observes the value written to the
+		 * KScratch register by the prior MTC0.
+		 */
+		if (scratch_reg >= 0)
+			uasm_i_ehb(p);
+
+		/* Reset default page size */
+		if (PM_DEFAULT_MASK >> 16) {
+			uasm_i_lui(p, tmp, PM_DEFAULT_MASK >> 16);
+			uasm_i_ori(p, tmp, tmp, PM_DEFAULT_MASK & 0xffff);
+			uasm_i_mtc0(p, tmp, C0_PAGEMASK);
+			uasm_il_b(p, r, lid);
+		} else if (PM_DEFAULT_MASK) {
+			uasm_i_ori(p, tmp, 0, PM_DEFAULT_MASK);
+			uasm_i_mtc0(p, tmp, C0_PAGEMASK);
+			uasm_il_b(p, r, lid);
+		} else {
+			uasm_i_mtc0(p, 0, C0_PAGEMASK);
+			uasm_il_b(p, r, lid);
+		}
+		if (scratch_reg >= 0)
+			UASM_i_MFC0(p, 1, c0_kscratch(), scratch_reg);
+		else
+			UASM_i_LW(p, 1, scratchpad_offset(0), 0);
+	} else {
+		/* Reset default page size */
+		if (PM_DEFAULT_MASK >> 16) {
+			uasm_i_lui(p, tmp, PM_DEFAULT_MASK >> 16);
+			uasm_i_ori(p, tmp, tmp, PM_DEFAULT_MASK & 0xffff);
+			uasm_il_b(p, r, lid);
+			uasm_i_mtc0(p, tmp, C0_PAGEMASK);
+		} else if (PM_DEFAULT_MASK) {
+			uasm_i_ori(p, tmp, 0, PM_DEFAULT_MASK);
+			uasm_il_b(p, r, lid);
+			uasm_i_mtc0(p, tmp, C0_PAGEMASK);
+		} else {
+			uasm_il_b(p, r, lid);
+			uasm_i_mtc0(p, 0, C0_PAGEMASK);
+		}
+	}
+}
+
+static void build_huge_tlb_write_entry(u32 **p, struct uasm_label **l,
+				       struct uasm_reloc **r,
+				       unsigned int tmp,
+				       enum tlb_write_entry wmode,
+				       int restore_scratch)
+{
+	/* Set huge page tlb entry size */
+	uasm_i_lui(p, tmp, PM_HUGE_MASK >> 16);
+	uasm_i_ori(p, tmp, tmp, PM_HUGE_MASK & 0xffff);
+	uasm_i_mtc0(p, tmp, C0_PAGEMASK);
+
+	build_tlb_write_entry(p, l, r, wmode);
+
+	build_restore_pagemask(p, r, tmp, label_leave, restore_scratch);
+}
+
+/*
+ * Check if Huge PTE is present, if so then jump to LABEL.
+ */
+static void
+build_is_huge_pte(u32 **p, struct uasm_reloc **r, unsigned int tmp,
+		  unsigned int pmd, int lid)
+{
+	UASM_i_LW(p, tmp, 0, pmd);
+	if (use_bbit_insns()) {
+		uasm_il_bbit1(p, r, tmp, ilog2(_PAGE_HUGE), lid);
+	} else {
+		uasm_i_andi(p, tmp, tmp, _PAGE_HUGE);
+		uasm_il_bnez(p, r, tmp, lid);
+	}
+}
+
+static void build_huge_update_entries(u32 **p, unsigned int pte,
+				      unsigned int tmp)
+{
+	int small_sequence;
+
+	/*
+	 * A huge PTE describes an area the size of the
+	 * configured huge page size. This is twice the
+	 * of the large TLB entry size we intend to use.
+	 * A TLB entry half the size of the configured
+	 * huge page size is configured into entrylo0
+	 * and entrylo1 to cover the contiguous huge PTE
+	 * address space.
+	 */
+	small_sequence = (HPAGE_SIZE >> 7) < 0x10000;
+
+	/* We can clobber tmp.	It isn't used after this.*/
+	if (!small_sequence)
+		uasm_i_lui(p, tmp, HPAGE_SIZE >> (7 + 16));
+
+	build_convert_pte_to_entrylo(p, pte);
+	UASM_i_MTC0(p, pte, C0_ENTRYLO0); /* load it */
+	/* convert to entrylo1 */
+	if (small_sequence)
+		UASM_i_ADDIU(p, pte, pte, HPAGE_SIZE >> 7);
+	else
+		UASM_i_ADDU(p, pte, pte, tmp);
+
+	UASM_i_MTC0(p, pte, C0_ENTRYLO1); /* load it */
+}
+
+static void build_huge_handler_tail(u32 **p, struct uasm_reloc **r,
+				    struct uasm_label **l,
+				    unsigned int pte,
+				    unsigned int ptr,
+				    unsigned int flush)
+{
+#ifdef CONFIG_SMP
+	UASM_i_SC(p, pte, 0, ptr);
+	uasm_il_beqz(p, r, pte, label_tlb_huge_update);
+	UASM_i_LW(p, pte, 0, ptr); /* Needed because SC killed our PTE */
+#else
+	UASM_i_SW(p, pte, 0, ptr);
+#endif
+	if (cpu_has_ftlb && flush) {
+		BUG_ON(!cpu_has_tlbinv);
+
+		UASM_i_MFC0(p, ptr, C0_ENTRYHI);
+		uasm_i_ori(p, ptr, ptr, MIPS_ENTRYHI_EHINV);
+		UASM_i_MTC0(p, ptr, C0_ENTRYHI);
+		build_tlb_write_entry(p, l, r, tlb_indexed);
+
+		uasm_i_xori(p, ptr, ptr, MIPS_ENTRYHI_EHINV);
+		UASM_i_MTC0(p, ptr, C0_ENTRYHI);
+		build_huge_update_entries(p, pte, ptr);
+		build_huge_tlb_write_entry(p, l, r, pte, tlb_random, 0);
+
+		return;
+	}
+
+	build_huge_update_entries(p, pte, ptr);
+	build_huge_tlb_write_entry(p, l, r, pte, tlb_indexed, 0);
+}
+#endif /* CONFIG_MIPS_HUGE_TLB_SUPPORT */
+
+#ifdef CONFIG_64BIT
+/*
+ * TMP and PTR are scratch.
+ * TMP will be clobbered, PTR will hold the pmd entry.
+ */
+void build_get_pmde64(u32 **p, struct uasm_label **l, struct uasm_reloc **r,
+		      unsigned int tmp, unsigned int ptr)
+{
+#ifndef CONFIG_MIPS_PGD_C0_CONTEXT
+	long pgdc = (long)pgd_current;
+#endif
+	/*
+	 * The vmalloc handling is not in the hotpath.
+	 */
+	uasm_i_dmfc0(p, tmp, C0_BADVADDR);
+
+	if (check_for_high_segbits) {
+		/*
+		 * The kernel currently implicitely assumes that the
+		 * MIPS SEGBITS parameter for the processor is
+		 * (PGDIR_SHIFT+PGDIR_BITS) or less, and will never
+		 * allocate virtual addresses outside the maximum
+		 * range for SEGBITS = (PGDIR_SHIFT+PGDIR_BITS). But
+		 * that doesn't prevent user code from accessing the
+		 * higher xuseg addresses.  Here, we make sure that
+		 * everything but the lower xuseg addresses goes down
+		 * the module_alloc/vmalloc path.
+		 */
+		uasm_i_dsrl_safe(p, ptr, tmp, PGDIR_SHIFT + PGD_TABLE_ORDER + PAGE_SHIFT - 3);
+		uasm_il_bnez(p, r, ptr, label_vmalloc);
+	} else {
+		uasm_il_bltz(p, r, tmp, label_vmalloc);
+	}
+	/* No uasm_i_nop needed here, since the next insn doesn't touch TMP. */
+
+	if (pgd_reg != -1) {
+		/* pgd is in pgd_reg */
+		if (cpu_has_ldpte)
+			UASM_i_MFC0(p, ptr, C0_PWBASE);
+		else
+			UASM_i_MFC0(p, ptr, c0_kscratch(), pgd_reg);
+	} else {
+#if defined(CONFIG_MIPS_PGD_C0_CONTEXT)
+		/*
+		 * &pgd << 11 stored in CONTEXT [23..63].
+		 */
+		UASM_i_MFC0(p, ptr, C0_CONTEXT);
+
+		/* Clear lower 23 bits of context. */
+		uasm_i_dins(p, ptr, 0, 0, 23);
+
+		/* insert bit[63:59] of CAC_BASE into bit[11:6] of ptr */
+		uasm_i_ori(p, ptr, ptr, ((u64)(CAC_BASE) >> 53));
+		uasm_i_drotr(p, ptr, ptr, 11);
+#elif defined(CONFIG_SMP)
+		UASM_i_CPUID_MFC0(p, ptr, SMP_CPUID_REG);
+		uasm_i_dsrl_safe(p, ptr, ptr, SMP_CPUID_PTRSHIFT);
+		UASM_i_LA_mostly(p, tmp, pgdc);
+		uasm_i_daddu(p, ptr, ptr, tmp);
+		uasm_i_dmfc0(p, tmp, C0_BADVADDR);
+		uasm_i_ld(p, ptr, uasm_rel_lo(pgdc), ptr);
+#else
+		UASM_i_LA_mostly(p, ptr, pgdc);
+		uasm_i_ld(p, ptr, uasm_rel_lo(pgdc), ptr);
+#endif
+	}
+
+	uasm_l_vmalloc_done(l, *p);
+
+	/* get pgd offset in bytes */
+	uasm_i_dsrl_safe(p, tmp, tmp, PGDIR_SHIFT - 3);
+
+	uasm_i_andi(p, tmp, tmp, (PTRS_PER_PGD - 1)<<3);
+	uasm_i_daddu(p, ptr, ptr, tmp); /* add in pgd offset */
+#ifndef __PAGETABLE_PUD_FOLDED
+	uasm_i_dmfc0(p, tmp, C0_BADVADDR); /* get faulting address */
+	uasm_i_ld(p, ptr, 0, ptr); /* get pud pointer */
+	uasm_i_dsrl_safe(p, tmp, tmp, PUD_SHIFT - 3); /* get pud offset in bytes */
+	uasm_i_andi(p, tmp, tmp, (PTRS_PER_PUD - 1) << 3);
+	uasm_i_daddu(p, ptr, ptr, tmp); /* add in pud offset */
+#endif
+#ifndef __PAGETABLE_PMD_FOLDED
+	uasm_i_dmfc0(p, tmp, C0_BADVADDR); /* get faulting address */
+	uasm_i_ld(p, ptr, 0, ptr); /* get pmd pointer */
+	uasm_i_dsrl_safe(p, tmp, tmp, PMD_SHIFT-3); /* get pmd offset in bytes */
+	uasm_i_andi(p, tmp, tmp, (PTRS_PER_PMD - 1)<<3);
+	uasm_i_daddu(p, ptr, ptr, tmp); /* add in pmd offset */
+#endif
+}
+EXPORT_SYMBOL_GPL(build_get_pmde64);
+
+/*
+ * BVADDR is the faulting address, PTR is scratch.
+ * PTR will hold the pgd for vmalloc.
+ */
+static void
+build_get_pgd_vmalloc64(u32 **p, struct uasm_label **l, struct uasm_reloc **r,
+			unsigned int bvaddr, unsigned int ptr,
+			enum vmalloc64_mode mode)
+{
+	long swpd = (long)swapper_pg_dir;
+	int single_insn_swpd;
+	int did_vmalloc_branch = 0;
+
+	single_insn_swpd = uasm_in_compat_space_p(swpd) && !uasm_rel_lo(swpd);
+
+	uasm_l_vmalloc(l, *p);
+
+	if (mode != not_refill && check_for_high_segbits) {
+		if (single_insn_swpd) {
+			uasm_il_bltz(p, r, bvaddr, label_vmalloc_done);
+			uasm_i_lui(p, ptr, uasm_rel_hi(swpd));
+			did_vmalloc_branch = 1;
+			/* fall through */
+		} else {
+			uasm_il_bgez(p, r, bvaddr, label_large_segbits_fault);
+		}
+	}
+	if (!did_vmalloc_branch) {
+		if (single_insn_swpd) {
+			uasm_il_b(p, r, label_vmalloc_done);
+			uasm_i_lui(p, ptr, uasm_rel_hi(swpd));
+		} else {
+			UASM_i_LA_mostly(p, ptr, swpd);
+			uasm_il_b(p, r, label_vmalloc_done);
+			if (uasm_in_compat_space_p(swpd))
+				uasm_i_addiu(p, ptr, ptr, uasm_rel_lo(swpd));
+			else
+				uasm_i_daddiu(p, ptr, ptr, uasm_rel_lo(swpd));
+		}
+	}
+	if (mode != not_refill && check_for_high_segbits) {
+		uasm_l_large_segbits_fault(l, *p);
+
+		if (mode == refill_scratch && scratch_reg >= 0)
+			uasm_i_ehb(p);
+
+		/*
+		 * We get here if we are an xsseg address, or if we are
+		 * an xuseg address above (PGDIR_SHIFT+PGDIR_BITS) boundary.
+		 *
+		 * Ignoring xsseg (assume disabled so would generate
+		 * (address errors?), the only remaining possibility
+		 * is the upper xuseg addresses.  On processors with
+		 * TLB_SEGBITS <= PGDIR_SHIFT+PGDIR_BITS, these
+		 * addresses would have taken an address error. We try
+		 * to mimic that here by taking a load/istream page
+		 * fault.
+		 */
+		if (IS_ENABLED(CONFIG_CPU_LOONGSON3_WORKAROUNDS))
+			uasm_i_sync(p, 0);
+		UASM_i_LA(p, ptr, (unsigned long)tlb_do_page_fault_0);
+		uasm_i_jr(p, ptr);
+
+		if (mode == refill_scratch) {
+			if (scratch_reg >= 0)
+				UASM_i_MFC0(p, 1, c0_kscratch(), scratch_reg);
+			else
+				UASM_i_LW(p, 1, scratchpad_offset(0), 0);
+		} else {
+			uasm_i_nop(p);
+		}
+	}
+}
+
+#else /* !CONFIG_64BIT */
+
+/*
+ * TMP and PTR are scratch.
+ * TMP will be clobbered, PTR will hold the pgd entry.
+ */
+void build_get_pgde32(u32 **p, unsigned int tmp, unsigned int ptr)
+{
+	if (pgd_reg != -1) {
+		/* pgd is in pgd_reg */
+		uasm_i_mfc0(p, ptr, c0_kscratch(), pgd_reg);
+		uasm_i_mfc0(p, tmp, C0_BADVADDR); /* get faulting address */
+	} else {
+		long pgdc = (long)pgd_current;
+
+		/* 32 bit SMP has smp_processor_id() stored in CONTEXT. */
+#ifdef CONFIG_SMP
+		uasm_i_mfc0(p, ptr, SMP_CPUID_REG);
+		UASM_i_LA_mostly(p, tmp, pgdc);
+		uasm_i_srl(p, ptr, ptr, SMP_CPUID_PTRSHIFT);
+		uasm_i_addu(p, ptr, tmp, ptr);
+#else
+		UASM_i_LA_mostly(p, ptr, pgdc);
+#endif
+		uasm_i_mfc0(p, tmp, C0_BADVADDR); /* get faulting address */
+		uasm_i_lw(p, ptr, uasm_rel_lo(pgdc), ptr);
+	}
+	uasm_i_srl(p, tmp, tmp, PGDIR_SHIFT); /* get pgd only bits */
+	uasm_i_sll(p, tmp, tmp, PGD_T_LOG2);
+	uasm_i_addu(p, ptr, ptr, tmp); /* add in pgd offset */
+}
+EXPORT_SYMBOL_GPL(build_get_pgde32);
+
+#endif /* !CONFIG_64BIT */
+
+static void build_adjust_context(u32 **p, unsigned int ctx)
+{
+	unsigned int shift = 4 - (PTE_T_LOG2 + 1) + PAGE_SHIFT - 12;
+	unsigned int mask = (PTRS_PER_PTE / 2 - 1) << (PTE_T_LOG2 + 1);
+
+	if (shift)
+		UASM_i_SRL(p, ctx, ctx, shift);
+	uasm_i_andi(p, ctx, ctx, mask);
+}
+
+void build_get_ptep(u32 **p, unsigned int tmp, unsigned int ptr)
+{
+	/*
+	 * Bug workaround for the Nevada. It seems as if under certain
+	 * circumstances the move from cp0_context might produce a
+	 * bogus result when the mfc0 instruction and its consumer are
+	 * in a different cacheline or a load instruction, probably any
+	 * memory reference, is between them.
+	 */
+	switch (current_cpu_type()) {
+	case CPU_NEVADA:
+		UASM_i_LW(p, ptr, 0, ptr);
+		GET_CONTEXT(p, tmp); /* get context reg */
+		break;
+
+	default:
+		GET_CONTEXT(p, tmp); /* get context reg */
+		UASM_i_LW(p, ptr, 0, ptr);
+		break;
+	}
+
+	build_adjust_context(p, tmp);
+	UASM_i_ADDU(p, ptr, ptr, tmp); /* add in offset */
+}
+EXPORT_SYMBOL_GPL(build_get_ptep);
+
+void build_update_entries(u32 **p, unsigned int tmp, unsigned int ptep)
+{
+	int pte_off_even = 0;
+	int pte_off_odd = sizeof(pte_t);
+
+#if defined(CONFIG_CPU_MIPS32) && defined(CONFIG_PHYS_ADDR_T_64BIT)
+	/* The low 32 bits of EntryLo is stored in pte_high */
+	pte_off_even += offsetof(pte_t, pte_high);
+	pte_off_odd += offsetof(pte_t, pte_high);
+#endif
+
+	if (IS_ENABLED(CONFIG_XPA)) {
+		uasm_i_lw(p, tmp, pte_off_even, ptep); /* even pte */
+		UASM_i_ROTR(p, tmp, tmp, ilog2(_PAGE_GLOBAL));
+		UASM_i_MTC0(p, tmp, C0_ENTRYLO0);
+
+		if (cpu_has_xpa && !mips_xpa_disabled) {
+			uasm_i_lw(p, tmp, 0, ptep);
+			uasm_i_ext(p, tmp, tmp, 0, 24);
+			uasm_i_mthc0(p, tmp, C0_ENTRYLO0);
+		}
+
+		uasm_i_lw(p, tmp, pte_off_odd, ptep); /* odd pte */
+		UASM_i_ROTR(p, tmp, tmp, ilog2(_PAGE_GLOBAL));
+		UASM_i_MTC0(p, tmp, C0_ENTRYLO1);
+
+		if (cpu_has_xpa && !mips_xpa_disabled) {
+			uasm_i_lw(p, tmp, sizeof(pte_t), ptep);
+			uasm_i_ext(p, tmp, tmp, 0, 24);
+			uasm_i_mthc0(p, tmp, C0_ENTRYLO1);
+		}
+		return;
+	}
+
+	UASM_i_LW(p, tmp, pte_off_even, ptep); /* get even pte */
+	UASM_i_LW(p, ptep, pte_off_odd, ptep); /* get odd pte */
+	if (r45k_bvahwbug())
+		build_tlb_probe_entry(p);
+	build_convert_pte_to_entrylo(p, tmp);
+	if (r4k_250MHZhwbug())
+		UASM_i_MTC0(p, 0, C0_ENTRYLO0);
+	UASM_i_MTC0(p, tmp, C0_ENTRYLO0); /* load it */
+	build_convert_pte_to_entrylo(p, ptep);
+	if (r45k_bvahwbug())
+		uasm_i_mfc0(p, tmp, C0_INDEX);
+	if (r4k_250MHZhwbug())
+		UASM_i_MTC0(p, 0, C0_ENTRYLO1);
+	UASM_i_MTC0(p, ptep, C0_ENTRYLO1); /* load it */
+}
+EXPORT_SYMBOL_GPL(build_update_entries);
+
+struct mips_huge_tlb_info {
+	int huge_pte;
+	int restore_scratch;
+	bool need_reload_pte;
+};
+
+static struct mips_huge_tlb_info
+build_fast_tlb_refill_handler (u32 **p, struct uasm_label **l,
+			       struct uasm_reloc **r, unsigned int tmp,
+			       unsigned int ptr, int c0_scratch_reg)
+{
+	struct mips_huge_tlb_info rv;
+	unsigned int even, odd;
+	int vmalloc_branch_delay_filled = 0;
+	const int scratch = 1; /* Our extra working register */
+
+	rv.huge_pte = scratch;
+	rv.restore_scratch = 0;
+	rv.need_reload_pte = false;
+
+	if (check_for_high_segbits) {
+		UASM_i_MFC0(p, tmp, C0_BADVADDR);
+
+		if (pgd_reg != -1)
+			UASM_i_MFC0(p, ptr, c0_kscratch(), pgd_reg);
+		else
+			UASM_i_MFC0(p, ptr, C0_CONTEXT);
+
+		if (c0_scratch_reg >= 0)
+			UASM_i_MTC0(p, scratch, c0_kscratch(), c0_scratch_reg);
+		else
+			UASM_i_SW(p, scratch, scratchpad_offset(0), 0);
+
+		uasm_i_dsrl_safe(p, scratch, tmp,
+				 PGDIR_SHIFT + PGD_TABLE_ORDER + PAGE_SHIFT - 3);
+		uasm_il_bnez(p, r, scratch, label_vmalloc);
+
+		if (pgd_reg == -1) {
+			vmalloc_branch_delay_filled = 1;
+			/* Clear lower 23 bits of context. */
+			uasm_i_dins(p, ptr, 0, 0, 23);
+		}
+	} else {
+		if (pgd_reg != -1)
+			UASM_i_MFC0(p, ptr, c0_kscratch(), pgd_reg);
+		else
+			UASM_i_MFC0(p, ptr, C0_CONTEXT);
+
+		UASM_i_MFC0(p, tmp, C0_BADVADDR);
+
+		if (c0_scratch_reg >= 0)
+			UASM_i_MTC0(p, scratch, c0_kscratch(), c0_scratch_reg);
+		else
+			UASM_i_SW(p, scratch, scratchpad_offset(0), 0);
+
+		if (pgd_reg == -1)
+			/* Clear lower 23 bits of context. */
+			uasm_i_dins(p, ptr, 0, 0, 23);
+
+		uasm_il_bltz(p, r, tmp, label_vmalloc);
+	}
+
+	if (pgd_reg == -1) {
+		vmalloc_branch_delay_filled = 1;
+		/* insert bit[63:59] of CAC_BASE into bit[11:6] of ptr */
+		uasm_i_ori(p, ptr, ptr, ((u64)(CAC_BASE) >> 53));
+
+		uasm_i_drotr(p, ptr, ptr, 11);
+	}
+
+#ifdef __PAGETABLE_PMD_FOLDED
+#define LOC_PTEP scratch
+#else
+#define LOC_PTEP ptr
+#endif
+
+	if (!vmalloc_branch_delay_filled)
+		/* get pgd offset in bytes */
+		uasm_i_dsrl_safe(p, scratch, tmp, PGDIR_SHIFT - 3);
+
+	uasm_l_vmalloc_done(l, *p);
+
+	/*
+	 *			   tmp		ptr
+	 * fall-through case =	 badvaddr  *pgd_current
+	 * vmalloc case	     =	 badvaddr  swapper_pg_dir
+	 */
+
+	if (vmalloc_branch_delay_filled)
+		/* get pgd offset in bytes */
+		uasm_i_dsrl_safe(p, scratch, tmp, PGDIR_SHIFT - 3);
+
+#ifdef __PAGETABLE_PMD_FOLDED
+	GET_CONTEXT(p, tmp); /* get context reg */
+#endif
+	uasm_i_andi(p, scratch, scratch, (PTRS_PER_PGD - 1) << 3);
+
+	if (use_lwx_insns()) {
+		UASM_i_LWX(p, LOC_PTEP, scratch, ptr);
+	} else {
+		uasm_i_daddu(p, ptr, ptr, scratch); /* add in pgd offset */
+		uasm_i_ld(p, LOC_PTEP, 0, ptr); /* get pmd pointer */
+	}
+
+#ifndef __PAGETABLE_PUD_FOLDED
+	/* get pud offset in bytes */
+	uasm_i_dsrl_safe(p, scratch, tmp, PUD_SHIFT - 3);
+	uasm_i_andi(p, scratch, scratch, (PTRS_PER_PUD - 1) << 3);
+
+	if (use_lwx_insns()) {
+		UASM_i_LWX(p, ptr, scratch, ptr);
+	} else {
+		uasm_i_daddu(p, ptr, ptr, scratch); /* add in pmd offset */
+		UASM_i_LW(p, ptr, 0, ptr);
+	}
+	/* ptr contains a pointer to PMD entry */
+	/* tmp contains the address */
+#endif
+
+#ifndef __PAGETABLE_PMD_FOLDED
+	/* get pmd offset in bytes */
+	uasm_i_dsrl_safe(p, scratch, tmp, PMD_SHIFT - 3);
+	uasm_i_andi(p, scratch, scratch, (PTRS_PER_PMD - 1) << 3);
+	GET_CONTEXT(p, tmp); /* get context reg */
+
+	if (use_lwx_insns()) {
+		UASM_i_LWX(p, scratch, scratch, ptr);
+	} else {
+		uasm_i_daddu(p, ptr, ptr, scratch); /* add in pmd offset */
+		UASM_i_LW(p, scratch, 0, ptr);
+	}
+#endif
+	/* Adjust the context during the load latency. */
+	build_adjust_context(p, tmp);
+
+#ifdef CONFIG_MIPS_HUGE_TLB_SUPPORT
+	uasm_il_bbit1(p, r, scratch, ilog2(_PAGE_HUGE), label_tlb_huge_update);
+	/*
+	 * The in the LWX case we don't want to do the load in the
+	 * delay slot.	It cannot issue in the same cycle and may be
+	 * speculative and unneeded.
+	 */
+	if (use_lwx_insns())
+		uasm_i_nop(p);
+#endif /* CONFIG_MIPS_HUGE_TLB_SUPPORT */
+
+
+	/* build_update_entries */
+	if (use_lwx_insns()) {
+		even = ptr;
+		odd = tmp;
+		UASM_i_LWX(p, even, scratch, tmp);
+		UASM_i_ADDIU(p, tmp, tmp, sizeof(pte_t));
+		UASM_i_LWX(p, odd, scratch, tmp);
+	} else {
+		UASM_i_ADDU(p, ptr, scratch, tmp); /* add in offset */
+		even = tmp;
+		odd = ptr;
+		UASM_i_LW(p, even, 0, ptr); /* get even pte */
+		UASM_i_LW(p, odd, sizeof(pte_t), ptr); /* get odd pte */
+	}
+	if (cpu_has_rixi) {
+		uasm_i_drotr(p, even, even, ilog2(_PAGE_GLOBAL));
+		UASM_i_MTC0(p, even, C0_ENTRYLO0); /* load it */
+		uasm_i_drotr(p, odd, odd, ilog2(_PAGE_GLOBAL));
+	} else {
+		uasm_i_dsrl_safe(p, even, even, ilog2(_PAGE_GLOBAL));
+		UASM_i_MTC0(p, even, C0_ENTRYLO0); /* load it */
+		uasm_i_dsrl_safe(p, odd, odd, ilog2(_PAGE_GLOBAL));
+	}
+	UASM_i_MTC0(p, odd, C0_ENTRYLO1); /* load it */
+
+	if (c0_scratch_reg >= 0) {
+		uasm_i_ehb(p);
+		UASM_i_MFC0(p, scratch, c0_kscratch(), c0_scratch_reg);
+		build_tlb_write_entry(p, l, r, tlb_random);
+		uasm_l_leave(l, *p);
+		rv.restore_scratch = 1;
+	} else if (PAGE_SHIFT == 14 || PAGE_SHIFT == 13)  {
+		build_tlb_write_entry(p, l, r, tlb_random);
+		uasm_l_leave(l, *p);
+		UASM_i_LW(p, scratch, scratchpad_offset(0), 0);
+	} else {
+		UASM_i_LW(p, scratch, scratchpad_offset(0), 0);
+		build_tlb_write_entry(p, l, r, tlb_random);
+		uasm_l_leave(l, *p);
+		rv.restore_scratch = 1;
+	}
+
+	uasm_i_eret(p); /* return from trap */
+
+	return rv;
+}
+
+/*
+ * For a 64-bit kernel, we are using the 64-bit XTLB refill exception
+ * because EXL == 0.  If we wrap, we can also use the 32 instruction
+ * slots before the XTLB refill exception handler which belong to the
+ * unused TLB refill exception.
+ */
+#define MIPS64_REFILL_INSNS 32
+
+static void build_r4000_tlb_refill_handler(void)
+{
+	u32 *p = tlb_handler;
+	struct uasm_label *l = labels;
+	struct uasm_reloc *r = relocs;
+	u32 *f;
+	unsigned int final_len;
+	struct mips_huge_tlb_info htlb_info __maybe_unused;
+	enum vmalloc64_mode vmalloc_mode __maybe_unused;
+
+	memset(tlb_handler, 0, sizeof(tlb_handler));
+	memset(labels, 0, sizeof(labels));
+	memset(relocs, 0, sizeof(relocs));
+	memset(final_handler, 0, sizeof(final_handler));
+
+	if (IS_ENABLED(CONFIG_64BIT) && (scratch_reg >= 0 || scratchpad_available()) && use_bbit_insns()) {
+		htlb_info = build_fast_tlb_refill_handler(&p, &l, &r, K0, K1,
+							  scratch_reg);
+		vmalloc_mode = refill_scratch;
+	} else {
+		htlb_info.huge_pte = K0;
+		htlb_info.restore_scratch = 0;
+		htlb_info.need_reload_pte = true;
+		vmalloc_mode = refill_noscratch;
+		/*
+		 * create the plain linear handler
+		 */
+		if (bcm1250_m3_war()) {
+			unsigned int segbits = 44;
+
+			uasm_i_dmfc0(&p, K0, C0_BADVADDR);
+			uasm_i_dmfc0(&p, K1, C0_ENTRYHI);
+			uasm_i_xor(&p, K0, K0, K1);
+			uasm_i_dsrl_safe(&p, K1, K0, 62);
+			uasm_i_dsrl_safe(&p, K0, K0, 12 + 1);
+			uasm_i_dsll_safe(&p, K0, K0, 64 + 12 + 1 - segbits);
+			uasm_i_or(&p, K0, K0, K1);
+			uasm_il_bnez(&p, &r, K0, label_leave);
+			/* No need for uasm_i_nop */
+		}
+
+#ifdef CONFIG_64BIT
+		build_get_pmde64(&p, &l, &r, K0, K1); /* get pmd in K1 */
+#else
+		build_get_pgde32(&p, K0, K1); /* get pgd in K1 */
+#endif
+
+#ifdef CONFIG_MIPS_HUGE_TLB_SUPPORT
+		build_is_huge_pte(&p, &r, K0, K1, label_tlb_huge_update);
+#endif
+
+		build_get_ptep(&p, K0, K1);
+		build_update_entries(&p, K0, K1);
+		build_tlb_write_entry(&p, &l, &r, tlb_random);
+		uasm_l_leave(&l, p);
+		uasm_i_eret(&p); /* return from trap */
+	}
+#ifdef CONFIG_MIPS_HUGE_TLB_SUPPORT
+	uasm_l_tlb_huge_update(&l, p);
+	if (htlb_info.need_reload_pte)
+		UASM_i_LW(&p, htlb_info.huge_pte, 0, K1);
+	build_huge_update_entries(&p, htlb_info.huge_pte, K1);
+	build_huge_tlb_write_entry(&p, &l, &r, K0, tlb_random,
+				   htlb_info.restore_scratch);
+#endif
+
+#ifdef CONFIG_64BIT
+	build_get_pgd_vmalloc64(&p, &l, &r, K0, K1, vmalloc_mode);
+#endif
+
+	/*
+	 * Overflow check: For the 64bit handler, we need at least one
+	 * free instruction slot for the wrap-around branch. In worst
+	 * case, if the intended insertion point is a delay slot, we
+	 * need three, with the second nop'ed and the third being
+	 * unused.
+	 */
+	switch (boot_cpu_type()) {
+	default:
+		if (sizeof(long) == 4) {
+		fallthrough;
+	case CPU_LOONGSON2EF:
+		/* Loongson2 ebase is different than r4k, we have more space */
+			if ((p - tlb_handler) > 64)
+				panic("TLB refill handler space exceeded");
+			/*
+			 * Now fold the handler in the TLB refill handler space.
+			 */
+			f = final_handler;
+			/* Simplest case, just copy the handler. */
+			uasm_copy_handler(relocs, labels, tlb_handler, p, f);
+			final_len = p - tlb_handler;
+			break;
+		} else {
+			if (((p - tlb_handler) > (MIPS64_REFILL_INSNS * 2) - 1)
+			    || (((p - tlb_handler) > (MIPS64_REFILL_INSNS * 2) - 3)
+				&& uasm_insn_has_bdelay(relocs,
+							tlb_handler + MIPS64_REFILL_INSNS - 3)))
+				panic("TLB refill handler space exceeded");
+			/*
+			 * Now fold the handler in the TLB refill handler space.
+			 */
+			f = final_handler + MIPS64_REFILL_INSNS;
+			if ((p - tlb_handler) <= MIPS64_REFILL_INSNS) {
+				/* Just copy the handler. */
+				uasm_copy_handler(relocs, labels, tlb_handler, p, f);
+				final_len = p - tlb_handler;
+			} else {
+#ifdef CONFIG_MIPS_HUGE_TLB_SUPPORT
+				const enum label_id ls = label_tlb_huge_update;
+#else
+				const enum label_id ls = label_vmalloc;
+#endif
+				u32 *split;
+				int ov = 0;
+				int i;
+
+				for (i = 0; i < ARRAY_SIZE(labels) && labels[i].lab != ls; i++)
+					;
+				BUG_ON(i == ARRAY_SIZE(labels));
+				split = labels[i].addr;
+
+				/*
+				 * See if we have overflown one way or the other.
+				 */
+				if (split > tlb_handler + MIPS64_REFILL_INSNS ||
+				    split < p - MIPS64_REFILL_INSNS)
+					ov = 1;
+
+				if (ov) {
+					/*
+					 * Split two instructions before the end.  One
+					 * for the branch and one for the instruction
+					 * in the delay slot.
+					 */
+					split = tlb_handler + MIPS64_REFILL_INSNS - 2;
+
+					/*
+					 * If the branch would fall in a delay slot,
+					 * we must back up an additional instruction
+					 * so that it is no longer in a delay slot.
+					 */
+					if (uasm_insn_has_bdelay(relocs, split - 1))
+						split--;
+				}
+				/* Copy first part of the handler. */
+				uasm_copy_handler(relocs, labels, tlb_handler, split, f);
+				f += split - tlb_handler;
+
+				if (ov) {
+					/* Insert branch. */
+					uasm_l_split(&l, final_handler);
+					uasm_il_b(&f, &r, label_split);
+					if (uasm_insn_has_bdelay(relocs, split))
+						uasm_i_nop(&f);
+					else {
+						uasm_copy_handler(relocs, labels,
+								  split, split + 1, f);
+						uasm_move_labels(labels, f, f + 1, -1);
+						f++;
+						split++;
+					}
+				}
+
+				/* Copy the rest of the handler. */
+				uasm_copy_handler(relocs, labels, split, p, final_handler);
+				final_len = (f - (final_handler + MIPS64_REFILL_INSNS)) +
+					    (p - split);
+			}
+		}
+		break;
+	}
+
+	uasm_resolve_relocs(relocs, labels);
+	pr_debug("Wrote TLB refill handler (%u instructions).\n",
+		 final_len);
+
+	memcpy((void *)ebase, final_handler, 0x100);
+	local_flush_icache_range(ebase, ebase + 0x100);
+	dump_handler("r4000_tlb_refill", (u32 *)ebase, (u32 *)(ebase + 0x100));
+}
+
+static void setup_pw(void)
+{
+	unsigned int pwctl;
+	unsigned long pgd_i, pgd_w;
+#ifndef __PAGETABLE_PMD_FOLDED
+	unsigned long pmd_i, pmd_w;
+#endif
+	unsigned long pt_i, pt_w;
+	unsigned long pte_i, pte_w;
+#ifdef CONFIG_MIPS_HUGE_TLB_SUPPORT
+	unsigned long psn;
+
+	psn = ilog2(_PAGE_HUGE);     /* bit used to indicate huge page */
+#endif
+	pgd_i = PGDIR_SHIFT;  /* 1st level PGD */
+#ifndef __PAGETABLE_PMD_FOLDED
+	pgd_w = PGDIR_SHIFT - PMD_SHIFT + PGD_TABLE_ORDER;
+
+	pmd_i = PMD_SHIFT;    /* 2nd level PMD */
+	pmd_w = PMD_SHIFT - PAGE_SHIFT;
+#else
+	pgd_w = PGDIR_SHIFT - PAGE_SHIFT + PGD_TABLE_ORDER;
+#endif
+
+	pt_i  = PAGE_SHIFT;    /* 3rd level PTE */
+	pt_w  = PAGE_SHIFT - 3;
+
+	pte_i = ilog2(_PAGE_GLOBAL);
+	pte_w = 0;
+	pwctl = 1 << 30; /* Set PWDirExt */
+
+#ifndef __PAGETABLE_PMD_FOLDED
+	write_c0_pwfield(pgd_i << 24 | pmd_i << 12 | pt_i << 6 | pte_i);
+	write_c0_pwsize(1 << 30 | pgd_w << 24 | pmd_w << 12 | pt_w << 6 | pte_w);
+#else
+	write_c0_pwfield(pgd_i << 24 | pt_i << 6 | pte_i);
+	write_c0_pwsize(1 << 30 | pgd_w << 24 | pt_w << 6 | pte_w);
+#endif
+
+#ifdef CONFIG_MIPS_HUGE_TLB_SUPPORT
+	pwctl |= (1 << 6 | psn);
+#endif
+	write_c0_pwctl(pwctl);
+	write_c0_kpgd((long)swapper_pg_dir);
+	kscratch_used_mask |= (1 << 7); /* KScratch6 is used for KPGD */
+}
+
+static void build_loongson3_tlb_refill_handler(void)
+{
+	u32 *p = tlb_handler;
+	struct uasm_label *l = labels;
+	struct uasm_reloc *r = relocs;
+
+	memset(labels, 0, sizeof(labels));
+	memset(relocs, 0, sizeof(relocs));
+	memset(tlb_handler, 0, sizeof(tlb_handler));
+
+	if (check_for_high_segbits) {
+		uasm_i_dmfc0(&p, K0, C0_BADVADDR);
+		uasm_i_dsrl_safe(&p, K1, K0, PGDIR_SHIFT + PGD_TABLE_ORDER + PAGE_SHIFT - 3);
+		uasm_il_beqz(&p, &r, K1, label_vmalloc);
+		uasm_i_nop(&p);
+
+		uasm_il_bgez(&p, &r, K0, label_large_segbits_fault);
+		uasm_i_nop(&p);
+		uasm_l_vmalloc(&l, p);
+	}
+
+	uasm_i_dmfc0(&p, K1, C0_PGD);
+
+	uasm_i_lddir(&p, K0, K1, 3);  /* global page dir */
+#ifndef __PAGETABLE_PMD_FOLDED
+	uasm_i_lddir(&p, K1, K0, 1);  /* middle page dir */
+#endif
+	uasm_i_ldpte(&p, K1, 0);      /* even */
+	uasm_i_ldpte(&p, K1, 1);      /* odd */
+	uasm_i_tlbwr(&p);
+
+	/* restore page mask */
+	if (PM_DEFAULT_MASK >> 16) {
+		uasm_i_lui(&p, K0, PM_DEFAULT_MASK >> 16);
+		uasm_i_ori(&p, K0, K0, PM_DEFAULT_MASK & 0xffff);
+		uasm_i_mtc0(&p, K0, C0_PAGEMASK);
+	} else if (PM_DEFAULT_MASK) {
+		uasm_i_ori(&p, K0, 0, PM_DEFAULT_MASK);
+		uasm_i_mtc0(&p, K0, C0_PAGEMASK);
+	} else {
+		uasm_i_mtc0(&p, 0, C0_PAGEMASK);
+	}
+
+	uasm_i_eret(&p);
+
+	if (check_for_high_segbits) {
+		uasm_l_large_segbits_fault(&l, p);
+		UASM_i_LA(&p, K1, (unsigned long)tlb_do_page_fault_0);
+		uasm_i_jr(&p, K1);
+		uasm_i_nop(&p);
+	}
+
+	uasm_resolve_relocs(relocs, labels);
+	memcpy((void *)(ebase + 0x80), tlb_handler, 0x80);
+	local_flush_icache_range(ebase + 0x80, ebase + 0x100);
+	dump_handler("loongson3_tlb_refill",
+		     (u32 *)(ebase + 0x80), (u32 *)(ebase + 0x100));
+}
+
+static void build_setup_pgd(void)
+{
+	const int a0 = 4;
+	const int __maybe_unused a1 = 5;
+	const int __maybe_unused a2 = 6;
+	u32 *p = (u32 *)msk_isa16_mode((ulong)tlbmiss_handler_setup_pgd);
+#ifndef CONFIG_MIPS_PGD_C0_CONTEXT
+	long pgdc = (long)pgd_current;
+#endif
+
+	memset(p, 0, tlbmiss_handler_setup_pgd_end - (char *)p);
+	memset(labels, 0, sizeof(labels));
+	memset(relocs, 0, sizeof(relocs));
+	pgd_reg = allocate_kscratch();
+#ifdef CONFIG_MIPS_PGD_C0_CONTEXT
+	if (pgd_reg == -1) {
+		struct uasm_label *l = labels;
+		struct uasm_reloc *r = relocs;
+
+		/* PGD << 11 in c0_Context */
+		/*
+		 * If it is a ckseg0 address, convert to a physical
+		 * address.  Shifting right by 29 and adding 4 will
+		 * result in zero for these addresses.
+		 *
+		 */
+		UASM_i_SRA(&p, a1, a0, 29);
+		UASM_i_ADDIU(&p, a1, a1, 4);
+		uasm_il_bnez(&p, &r, a1, label_tlbl_goaround1);
+		uasm_i_nop(&p);
+		uasm_i_dinsm(&p, a0, 0, 29, 64 - 29);
+		uasm_l_tlbl_goaround1(&l, p);
+		UASM_i_SLL(&p, a0, a0, 11);
+		UASM_i_MTC0(&p, a0, C0_CONTEXT);
+		uasm_i_jr(&p, 31);
+		uasm_i_ehb(&p);
+	} else {
+		/* PGD in c0_KScratch */
+		if (cpu_has_ldpte)
+			UASM_i_MTC0(&p, a0, C0_PWBASE);
+		else
+			UASM_i_MTC0(&p, a0, c0_kscratch(), pgd_reg);
+		uasm_i_jr(&p, 31);
+		uasm_i_ehb(&p);
+	}
+#else
+#ifdef CONFIG_SMP
+	/* Save PGD to pgd_current[smp_processor_id()] */
+	UASM_i_CPUID_MFC0(&p, a1, SMP_CPUID_REG);
+	UASM_i_SRL_SAFE(&p, a1, a1, SMP_CPUID_PTRSHIFT);
+	UASM_i_LA_mostly(&p, a2, pgdc);
+	UASM_i_ADDU(&p, a2, a2, a1);
+	UASM_i_SW(&p, a0, uasm_rel_lo(pgdc), a2);
+#else
+	UASM_i_LA_mostly(&p, a2, pgdc);
+	UASM_i_SW(&p, a0, uasm_rel_lo(pgdc), a2);
+#endif /* SMP */
+
+	/* if pgd_reg is allocated, save PGD also to scratch register */
+	if (pgd_reg != -1) {
+		UASM_i_MTC0(&p, a0, c0_kscratch(), pgd_reg);
+		uasm_i_jr(&p, 31);
+		uasm_i_ehb(&p);
+	} else {
+		uasm_i_jr(&p, 31);
+		uasm_i_nop(&p);
+	}
+#endif
+	if (p >= (u32 *)tlbmiss_handler_setup_pgd_end)
+		panic("tlbmiss_handler_setup_pgd space exceeded");
+
+	uasm_resolve_relocs(relocs, labels);
+	pr_debug("Wrote tlbmiss_handler_setup_pgd (%u instructions).\n",
+		 (unsigned int)(p - (u32 *)tlbmiss_handler_setup_pgd));
+
+	dump_handler("tlbmiss_handler", tlbmiss_handler_setup_pgd,
+					tlbmiss_handler_setup_pgd_end);
+}
+
+static void
+iPTE_LW(u32 **p, unsigned int pte, unsigned int ptr)
+{
+#ifdef CONFIG_SMP
+	if (IS_ENABLED(CONFIG_CPU_LOONGSON3_WORKAROUNDS))
+		uasm_i_sync(p, 0);
+# ifdef CONFIG_PHYS_ADDR_T_64BIT
+	if (cpu_has_64bits)
+		uasm_i_lld(p, pte, 0, ptr);
+	else
+# endif
+		UASM_i_LL(p, pte, 0, ptr);
+#else
+# ifdef CONFIG_PHYS_ADDR_T_64BIT
+	if (cpu_has_64bits)
+		uasm_i_ld(p, pte, 0, ptr);
+	else
+# endif
+		UASM_i_LW(p, pte, 0, ptr);
+#endif
+}
+
+static void
+iPTE_SW(u32 **p, struct uasm_reloc **r, unsigned int pte, unsigned int ptr,
+	unsigned int mode, unsigned int scratch)
+{
+	unsigned int hwmode = mode & (_PAGE_VALID | _PAGE_DIRTY);
+	unsigned int swmode = mode & ~hwmode;
+
+	if (IS_ENABLED(CONFIG_XPA) && !cpu_has_64bits) {
+		uasm_i_lui(p, scratch, swmode >> 16);
+		uasm_i_or(p, pte, pte, scratch);
+		BUG_ON(swmode & 0xffff);
+	} else {
+		uasm_i_ori(p, pte, pte, mode);
+	}
+
+#ifdef CONFIG_SMP
+# ifdef CONFIG_PHYS_ADDR_T_64BIT
+	if (cpu_has_64bits)
+		uasm_i_scd(p, pte, 0, ptr);
+	else
+# endif
+		UASM_i_SC(p, pte, 0, ptr);
+
+	if (r10000_llsc_war())
+		uasm_il_beqzl(p, r, pte, label_smp_pgtable_change);
+	else
+		uasm_il_beqz(p, r, pte, label_smp_pgtable_change);
+
+# ifdef CONFIG_PHYS_ADDR_T_64BIT
+	if (!cpu_has_64bits) {
+		/* no uasm_i_nop needed */
+		uasm_i_ll(p, pte, sizeof(pte_t) / 2, ptr);
+		uasm_i_ori(p, pte, pte, hwmode);
+		BUG_ON(hwmode & ~0xffff);
+		uasm_i_sc(p, pte, sizeof(pte_t) / 2, ptr);
+		uasm_il_beqz(p, r, pte, label_smp_pgtable_change);
+		/* no uasm_i_nop needed */
+		uasm_i_lw(p, pte, 0, ptr);
+	} else
+		uasm_i_nop(p);
+# else
+	uasm_i_nop(p);
+# endif
+#else
+# ifdef CONFIG_PHYS_ADDR_T_64BIT
+	if (cpu_has_64bits)
+		uasm_i_sd(p, pte, 0, ptr);
+	else
+# endif
+		UASM_i_SW(p, pte, 0, ptr);
+
+# ifdef CONFIG_PHYS_ADDR_T_64BIT
+	if (!cpu_has_64bits) {
+		uasm_i_lw(p, pte, sizeof(pte_t) / 2, ptr);
+		uasm_i_ori(p, pte, pte, hwmode);
+		BUG_ON(hwmode & ~0xffff);
+		uasm_i_sw(p, pte, sizeof(pte_t) / 2, ptr);
+		uasm_i_lw(p, pte, 0, ptr);
+	}
+# endif
+#endif
+}
+
+/*
+ * Check if PTE is present, if not then jump to LABEL. PTR points to
+ * the page table where this PTE is located, PTE will be re-loaded
+ * with it's original value.
+ */
+static void
+build_pte_present(u32 **p, struct uasm_reloc **r,
+		  int pte, int ptr, int scratch, enum label_id lid)
+{
+	int t = scratch >= 0 ? scratch : pte;
+	int cur = pte;
+
+	if (cpu_has_rixi) {
+		if (use_bbit_insns()) {
+			uasm_il_bbit0(p, r, pte, ilog2(_PAGE_PRESENT), lid);
+			uasm_i_nop(p);
+		} else {
+			if (_PAGE_PRESENT_SHIFT) {
+				uasm_i_srl(p, t, cur, _PAGE_PRESENT_SHIFT);
+				cur = t;
+			}
+			uasm_i_andi(p, t, cur, 1);
+			uasm_il_beqz(p, r, t, lid);
+			if (pte == t)
+				/* You lose the SMP race :-(*/
+				iPTE_LW(p, pte, ptr);
+		}
+	} else {
+		if (_PAGE_PRESENT_SHIFT) {
+			uasm_i_srl(p, t, cur, _PAGE_PRESENT_SHIFT);
+			cur = t;
+		}
+		uasm_i_andi(p, t, cur,
+			(_PAGE_PRESENT | _PAGE_NO_READ) >> _PAGE_PRESENT_SHIFT);
+		uasm_i_xori(p, t, t, _PAGE_PRESENT >> _PAGE_PRESENT_SHIFT);
+		uasm_il_bnez(p, r, t, lid);
+		if (pte == t)
+			/* You lose the SMP race :-(*/
+			iPTE_LW(p, pte, ptr);
+	}
+}
+
+/* Make PTE valid, store result in PTR. */
+static void
+build_make_valid(u32 **p, struct uasm_reloc **r, unsigned int pte,
+		 unsigned int ptr, unsigned int scratch)
+{
+	unsigned int mode = _PAGE_VALID | _PAGE_ACCESSED;
+
+	iPTE_SW(p, r, pte, ptr, mode, scratch);
+}
+
+/*
+ * Check if PTE can be written to, if not branch to LABEL. Regardless
+ * restore PTE with value from PTR when done.
+ */
+static void
+build_pte_writable(u32 **p, struct uasm_reloc **r,
+		   unsigned int pte, unsigned int ptr, int scratch,
+		   enum label_id lid)
+{
+	int t = scratch >= 0 ? scratch : pte;
+	int cur = pte;
+
+	if (_PAGE_PRESENT_SHIFT) {
+		uasm_i_srl(p, t, cur, _PAGE_PRESENT_SHIFT);
+		cur = t;
+	}
+	uasm_i_andi(p, t, cur,
+		    (_PAGE_PRESENT | _PAGE_WRITE) >> _PAGE_PRESENT_SHIFT);
+	uasm_i_xori(p, t, t,
+		    (_PAGE_PRESENT | _PAGE_WRITE) >> _PAGE_PRESENT_SHIFT);
+	uasm_il_bnez(p, r, t, lid);
+	if (pte == t)
+		/* You lose the SMP race :-(*/
+		iPTE_LW(p, pte, ptr);
+	else
+		uasm_i_nop(p);
+}
+
+/* Make PTE writable, update software status bits as well, then store
+ * at PTR.
+ */
+static void
+build_make_write(u32 **p, struct uasm_reloc **r, unsigned int pte,
+		 unsigned int ptr, unsigned int scratch)
+{
+	unsigned int mode = (_PAGE_ACCESSED | _PAGE_MODIFIED | _PAGE_VALID
+			     | _PAGE_DIRTY);
+
+	iPTE_SW(p, r, pte, ptr, mode, scratch);
+}
+
+/*
+ * Check if PTE can be modified, if not branch to LABEL. Regardless
+ * restore PTE with value from PTR when done.
+ */
+static void
+build_pte_modifiable(u32 **p, struct uasm_reloc **r,
+		     unsigned int pte, unsigned int ptr, int scratch,
+		     enum label_id lid)
+{
+	if (use_bbit_insns()) {
+		uasm_il_bbit0(p, r, pte, ilog2(_PAGE_WRITE), lid);
+		uasm_i_nop(p);
+	} else {
+		int t = scratch >= 0 ? scratch : pte;
+		uasm_i_srl(p, t, pte, _PAGE_WRITE_SHIFT);
+		uasm_i_andi(p, t, t, 1);
+		uasm_il_beqz(p, r, t, lid);
+		if (pte == t)
+			/* You lose the SMP race :-(*/
+			iPTE_LW(p, pte, ptr);
+	}
+}
+
+#ifndef CONFIG_MIPS_PGD_C0_CONTEXT
+
+
+/*
+ * R3000 style TLB load/store/modify handlers.
+ */
+
+/*
+ * This places the pte into ENTRYLO0 and writes it with tlbwi.
+ * Then it returns.
+ */
+static void
+build_r3000_pte_reload_tlbwi(u32 **p, unsigned int pte, unsigned int tmp)
+{
+	uasm_i_mtc0(p, pte, C0_ENTRYLO0); /* cp0 delay */
+	uasm_i_mfc0(p, tmp, C0_EPC); /* cp0 delay */
+	uasm_i_tlbwi(p);
+	uasm_i_jr(p, tmp);
+	uasm_i_rfe(p); /* branch delay */
+}
+
+/*
+ * This places the pte into ENTRYLO0 and writes it with tlbwi
+ * or tlbwr as appropriate.  This is because the index register
+ * may have the probe fail bit set as a result of a trap on a
+ * kseg2 access, i.e. without refill.  Then it returns.
+ */
+static void
+build_r3000_tlb_reload_write(u32 **p, struct uasm_label **l,
+			     struct uasm_reloc **r, unsigned int pte,
+			     unsigned int tmp)
+{
+	uasm_i_mfc0(p, tmp, C0_INDEX);
+	uasm_i_mtc0(p, pte, C0_ENTRYLO0); /* cp0 delay */
+	uasm_il_bltz(p, r, tmp, label_r3000_write_probe_fail); /* cp0 delay */
+	uasm_i_mfc0(p, tmp, C0_EPC); /* branch delay */
+	uasm_i_tlbwi(p); /* cp0 delay */
+	uasm_i_jr(p, tmp);
+	uasm_i_rfe(p); /* branch delay */
+	uasm_l_r3000_write_probe_fail(l, *p);
+	uasm_i_tlbwr(p); /* cp0 delay */
+	uasm_i_jr(p, tmp);
+	uasm_i_rfe(p); /* branch delay */
+}
+
+static void
+build_r3000_tlbchange_handler_head(u32 **p, unsigned int pte,
+				   unsigned int ptr)
+{
+	long pgdc = (long)pgd_current;
+
+	uasm_i_mfc0(p, pte, C0_BADVADDR);
+	uasm_i_lui(p, ptr, uasm_rel_hi(pgdc)); /* cp0 delay */
+	uasm_i_lw(p, ptr, uasm_rel_lo(pgdc), ptr);
+	uasm_i_srl(p, pte, pte, 22); /* load delay */
+	uasm_i_sll(p, pte, pte, 2);
+	uasm_i_addu(p, ptr, ptr, pte);
+	uasm_i_mfc0(p, pte, C0_CONTEXT);
+	uasm_i_lw(p, ptr, 0, ptr); /* cp0 delay */
+	uasm_i_andi(p, pte, pte, 0xffc); /* load delay */
+	uasm_i_addu(p, ptr, ptr, pte);
+	uasm_i_lw(p, pte, 0, ptr);
+	uasm_i_tlbp(p); /* load delay */
+}
+
+static void build_r3000_tlb_load_handler(void)
+{
+	u32 *p = (u32 *)handle_tlbl;
+	struct uasm_label *l = labels;
+	struct uasm_reloc *r = relocs;
+
+	memset(p, 0, handle_tlbl_end - (char *)p);
+	memset(labels, 0, sizeof(labels));
+	memset(relocs, 0, sizeof(relocs));
+
+	build_r3000_tlbchange_handler_head(&p, K0, K1);
+	build_pte_present(&p, &r, K0, K1, -1, label_nopage_tlbl);
+	uasm_i_nop(&p); /* load delay */
+	build_make_valid(&p, &r, K0, K1, -1);
+	build_r3000_tlb_reload_write(&p, &l, &r, K0, K1);
+
+	uasm_l_nopage_tlbl(&l, p);
+	uasm_i_j(&p, (unsigned long)tlb_do_page_fault_0 & 0x0fffffff);
+	uasm_i_nop(&p);
+
+	if (p >= (u32 *)handle_tlbl_end)
+		panic("TLB load handler fastpath space exceeded");
+
+	uasm_resolve_relocs(relocs, labels);
+	pr_debug("Wrote TLB load handler fastpath (%u instructions).\n",
+		 (unsigned int)(p - (u32 *)handle_tlbl));
+
+	dump_handler("r3000_tlb_load", handle_tlbl, handle_tlbl_end);
+}
+
+static void build_r3000_tlb_store_handler(void)
+{
+	u32 *p = (u32 *)handle_tlbs;
+	struct uasm_label *l = labels;
+	struct uasm_reloc *r = relocs;
+
+	memset(p, 0, handle_tlbs_end - (char *)p);
+	memset(labels, 0, sizeof(labels));
+	memset(relocs, 0, sizeof(relocs));
+
+	build_r3000_tlbchange_handler_head(&p, K0, K1);
+	build_pte_writable(&p, &r, K0, K1, -1, label_nopage_tlbs);
+	uasm_i_nop(&p); /* load delay */
+	build_make_write(&p, &r, K0, K1, -1);
+	build_r3000_tlb_reload_write(&p, &l, &r, K0, K1);
+
+	uasm_l_nopage_tlbs(&l, p);
+	uasm_i_j(&p, (unsigned long)tlb_do_page_fault_1 & 0x0fffffff);
+	uasm_i_nop(&p);
+
+	if (p >= (u32 *)handle_tlbs_end)
+		panic("TLB store handler fastpath space exceeded");
+
+	uasm_resolve_relocs(relocs, labels);
+	pr_debug("Wrote TLB store handler fastpath (%u instructions).\n",
+		 (unsigned int)(p - (u32 *)handle_tlbs));
+
+	dump_handler("r3000_tlb_store", handle_tlbs, handle_tlbs_end);
+}
+
+static void build_r3000_tlb_modify_handler(void)
+{
+	u32 *p = (u32 *)handle_tlbm;
+	struct uasm_label *l = labels;
+	struct uasm_reloc *r = relocs;
+
+	memset(p, 0, handle_tlbm_end - (char *)p);
+	memset(labels, 0, sizeof(labels));
+	memset(relocs, 0, sizeof(relocs));
+
+	build_r3000_tlbchange_handler_head(&p, K0, K1);
+	build_pte_modifiable(&p, &r, K0, K1,  -1, label_nopage_tlbm);
+	uasm_i_nop(&p); /* load delay */
+	build_make_write(&p, &r, K0, K1, -1);
+	build_r3000_pte_reload_tlbwi(&p, K0, K1);
+
+	uasm_l_nopage_tlbm(&l, p);
+	uasm_i_j(&p, (unsigned long)tlb_do_page_fault_1 & 0x0fffffff);
+	uasm_i_nop(&p);
+
+	if (p >= (u32 *)handle_tlbm_end)
+		panic("TLB modify handler fastpath space exceeded");
+
+	uasm_resolve_relocs(relocs, labels);
+	pr_debug("Wrote TLB modify handler fastpath (%u instructions).\n",
+		 (unsigned int)(p - (u32 *)handle_tlbm));
+
+	dump_handler("r3000_tlb_modify", handle_tlbm, handle_tlbm_end);
+}
+#endif /* CONFIG_MIPS_PGD_C0_CONTEXT */
+
+static bool cpu_has_tlbex_tlbp_race(void)
+{
+	/*
+	 * When a Hardware Table Walker is running it can replace TLB entries
+	 * at any time, leading to a race between it & the CPU.
+	 */
+	if (cpu_has_htw)
+		return true;
+
+	/*
+	 * If the CPU shares FTLB RAM with its siblings then our entry may be
+	 * replaced at any time by a sibling performing a write to the FTLB.
+	 */
+	if (cpu_has_shared_ftlb_ram)
+		return true;
+
+	/* In all other cases there ought to be no race condition to handle */
+	return false;
+}
+
+/*
+ * R4000 style TLB load/store/modify handlers.
+ */
+static struct work_registers
+build_r4000_tlbchange_handler_head(u32 **p, struct uasm_label **l,
+				   struct uasm_reloc **r)
+{
+	struct work_registers wr = build_get_work_registers(p);
+
+#ifdef CONFIG_64BIT
+	build_get_pmde64(p, l, r, wr.r1, wr.r2); /* get pmd in ptr */
+#else
+	build_get_pgde32(p, wr.r1, wr.r2); /* get pgd in ptr */
+#endif
+
+#ifdef CONFIG_MIPS_HUGE_TLB_SUPPORT
+	/*
+	 * For huge tlb entries, pmd doesn't contain an address but
+	 * instead contains the tlb pte. Check the PAGE_HUGE bit and
+	 * see if we need to jump to huge tlb processing.
+	 */
+	build_is_huge_pte(p, r, wr.r1, wr.r2, label_tlb_huge_update);
+#endif
+
+	UASM_i_MFC0(p, wr.r1, C0_BADVADDR);
+	UASM_i_LW(p, wr.r2, 0, wr.r2);
+	UASM_i_SRL(p, wr.r1, wr.r1, PAGE_SHIFT - PTE_T_LOG2);
+	uasm_i_andi(p, wr.r1, wr.r1, (PTRS_PER_PTE - 1) << PTE_T_LOG2);
+	UASM_i_ADDU(p, wr.r2, wr.r2, wr.r1);
+
+#ifdef CONFIG_SMP
+	uasm_l_smp_pgtable_change(l, *p);
+#endif
+	iPTE_LW(p, wr.r1, wr.r2); /* get even pte */
+	if (!m4kc_tlbp_war()) {
+		build_tlb_probe_entry(p);
+		if (cpu_has_tlbex_tlbp_race()) {
+			/* race condition happens, leaving */
+			uasm_i_ehb(p);
+			uasm_i_mfc0(p, wr.r3, C0_INDEX);
+			uasm_il_bltz(p, r, wr.r3, label_leave);
+			uasm_i_nop(p);
+		}
+	}
+	return wr;
+}
+
+static void
+build_r4000_tlbchange_handler_tail(u32 **p, struct uasm_label **l,
+				   struct uasm_reloc **r, unsigned int tmp,
+				   unsigned int ptr)
+{
+	uasm_i_ori(p, ptr, ptr, sizeof(pte_t));
+	uasm_i_xori(p, ptr, ptr, sizeof(pte_t));
+	build_update_entries(p, tmp, ptr);
+	build_tlb_write_entry(p, l, r, tlb_indexed);
+	uasm_l_leave(l, *p);
+	build_restore_work_registers(p);
+	uasm_i_eret(p); /* return from trap */
+
+#ifdef CONFIG_64BIT
+	build_get_pgd_vmalloc64(p, l, r, tmp, ptr, not_refill);
+#endif
+}
+
+static void build_r4000_tlb_load_handler(void)
+{
+	u32 *p = (u32 *)msk_isa16_mode((ulong)handle_tlbl);
+	struct uasm_label *l = labels;
+	struct uasm_reloc *r = relocs;
+	struct work_registers wr;
+
+	memset(p, 0, handle_tlbl_end - (char *)p);
+	memset(labels, 0, sizeof(labels));
+	memset(relocs, 0, sizeof(relocs));
+
+	if (bcm1250_m3_war()) {
+		unsigned int segbits = 44;
+
+		uasm_i_dmfc0(&p, K0, C0_BADVADDR);
+		uasm_i_dmfc0(&p, K1, C0_ENTRYHI);
+		uasm_i_xor(&p, K0, K0, K1);
+		uasm_i_dsrl_safe(&p, K1, K0, 62);
+		uasm_i_dsrl_safe(&p, K0, K0, 12 + 1);
+		uasm_i_dsll_safe(&p, K0, K0, 64 + 12 + 1 - segbits);
+		uasm_i_or(&p, K0, K0, K1);
+		uasm_il_bnez(&p, &r, K0, label_leave);
+		/* No need for uasm_i_nop */
+	}
+
+	wr = build_r4000_tlbchange_handler_head(&p, &l, &r);
+	build_pte_present(&p, &r, wr.r1, wr.r2, wr.r3, label_nopage_tlbl);
+	if (m4kc_tlbp_war())
+		build_tlb_probe_entry(&p);
+
+	if (cpu_has_rixi && !cpu_has_rixiex) {
+		/*
+		 * If the page is not _PAGE_VALID, RI or XI could not
+		 * have triggered it.  Skip the expensive test..
+		 */
+		if (use_bbit_insns()) {
+			uasm_il_bbit0(&p, &r, wr.r1, ilog2(_PAGE_VALID),
+				      label_tlbl_goaround1);
+		} else {
+			uasm_i_andi(&p, wr.r3, wr.r1, _PAGE_VALID);
+			uasm_il_beqz(&p, &r, wr.r3, label_tlbl_goaround1);
+		}
+		uasm_i_nop(&p);
+
+		/*
+		 * Warn if something may race with us & replace the TLB entry
+		 * before we read it here. Everything with such races should
+		 * also have dedicated RiXi exception handlers, so this
+		 * shouldn't be hit.
+		 */
+		WARN(cpu_has_tlbex_tlbp_race(), "Unhandled race in RiXi path");
+
+		uasm_i_tlbr(&p);
+
+		switch (current_cpu_type()) {
+		case CPU_CAVIUM_OCTEON:
+		case CPU_CAVIUM_OCTEON_PLUS:
+		case CPU_CAVIUM_OCTEON2:
+			break;
+		default:
+			if (cpu_has_mips_r2_exec_hazard)
+				uasm_i_ehb(&p);
+			break;
+		}
+
+		/* Examine  entrylo 0 or 1 based on ptr. */
+		if (use_bbit_insns()) {
+			uasm_i_bbit0(&p, wr.r2, ilog2(sizeof(pte_t)), 8);
+		} else {
+			uasm_i_andi(&p, wr.r3, wr.r2, sizeof(pte_t));
+			uasm_i_beqz(&p, wr.r3, 8);
+		}
+		/* load it in the delay slot*/
+		UASM_i_MFC0(&p, wr.r3, C0_ENTRYLO0);
+		/* load it if ptr is odd */
+		UASM_i_MFC0(&p, wr.r3, C0_ENTRYLO1);
+		/*
+		 * If the entryLo (now in wr.r3) is valid (bit 1), RI or
+		 * XI must have triggered it.
+		 */
+		if (use_bbit_insns()) {
+			uasm_il_bbit1(&p, &r, wr.r3, 1, label_nopage_tlbl);
+			uasm_i_nop(&p);
+			uasm_l_tlbl_goaround1(&l, p);
+		} else {
+			uasm_i_andi(&p, wr.r3, wr.r3, 2);
+			uasm_il_bnez(&p, &r, wr.r3, label_nopage_tlbl);
+			uasm_i_nop(&p);
+		}
+		uasm_l_tlbl_goaround1(&l, p);
+	}
+	build_make_valid(&p, &r, wr.r1, wr.r2, wr.r3);
+	build_r4000_tlbchange_handler_tail(&p, &l, &r, wr.r1, wr.r2);
+
+#ifdef CONFIG_MIPS_HUGE_TLB_SUPPORT
+	/*
+	 * This is the entry point when build_r4000_tlbchange_handler_head
+	 * spots a huge page.
+	 */
+	uasm_l_tlb_huge_update(&l, p);
+	iPTE_LW(&p, wr.r1, wr.r2);
+	build_pte_present(&p, &r, wr.r1, wr.r2, wr.r3, label_nopage_tlbl);
+	build_tlb_probe_entry(&p);
+
+	if (cpu_has_rixi && !cpu_has_rixiex) {
+		/*
+		 * If the page is not _PAGE_VALID, RI or XI could not
+		 * have triggered it.  Skip the expensive test..
+		 */
+		if (use_bbit_insns()) {
+			uasm_il_bbit0(&p, &r, wr.r1, ilog2(_PAGE_VALID),
+				      label_tlbl_goaround2);
+		} else {
+			uasm_i_andi(&p, wr.r3, wr.r1, _PAGE_VALID);
+			uasm_il_beqz(&p, &r, wr.r3, label_tlbl_goaround2);
+		}
+		uasm_i_nop(&p);
+
+		/*
+		 * Warn if something may race with us & replace the TLB entry
+		 * before we read it here. Everything with such races should
+		 * also have dedicated RiXi exception handlers, so this
+		 * shouldn't be hit.
+		 */
+		WARN(cpu_has_tlbex_tlbp_race(), "Unhandled race in RiXi path");
+
+		uasm_i_tlbr(&p);
+
+		switch (current_cpu_type()) {
+		case CPU_CAVIUM_OCTEON:
+		case CPU_CAVIUM_OCTEON_PLUS:
+		case CPU_CAVIUM_OCTEON2:
+			break;
+		default:
+			if (cpu_has_mips_r2_exec_hazard)
+				uasm_i_ehb(&p);
+			break;
+		}
+
+		/* Examine  entrylo 0 or 1 based on ptr. */
+		if (use_bbit_insns()) {
+			uasm_i_bbit0(&p, wr.r2, ilog2(sizeof(pte_t)), 8);
+		} else {
+			uasm_i_andi(&p, wr.r3, wr.r2, sizeof(pte_t));
+			uasm_i_beqz(&p, wr.r3, 8);
+		}
+		/* load it in the delay slot*/
+		UASM_i_MFC0(&p, wr.r3, C0_ENTRYLO0);
+		/* load it if ptr is odd */
+		UASM_i_MFC0(&p, wr.r3, C0_ENTRYLO1);
+		/*
+		 * If the entryLo (now in wr.r3) is valid (bit 1), RI or
+		 * XI must have triggered it.
+		 */
+		if (use_bbit_insns()) {
+			uasm_il_bbit0(&p, &r, wr.r3, 1, label_tlbl_goaround2);
+		} else {
+			uasm_i_andi(&p, wr.r3, wr.r3, 2);
+			uasm_il_beqz(&p, &r, wr.r3, label_tlbl_goaround2);
+		}
+		if (PM_DEFAULT_MASK == 0)
+			uasm_i_nop(&p);
+		/*
+		 * We clobbered C0_PAGEMASK, restore it.  On the other branch
+		 * it is restored in build_huge_tlb_write_entry.
+		 */
+		build_restore_pagemask(&p, &r, wr.r3, label_nopage_tlbl, 0);
+
+		uasm_l_tlbl_goaround2(&l, p);
+	}
+	uasm_i_ori(&p, wr.r1, wr.r1, (_PAGE_ACCESSED | _PAGE_VALID));
+	build_huge_handler_tail(&p, &r, &l, wr.r1, wr.r2, 1);
+#endif
+
+	uasm_l_nopage_tlbl(&l, p);
+	if (IS_ENABLED(CONFIG_CPU_LOONGSON3_WORKAROUNDS))
+		uasm_i_sync(&p, 0);
+	build_restore_work_registers(&p);
+#ifdef CONFIG_CPU_MICROMIPS
+	if ((unsigned long)tlb_do_page_fault_0 & 1) {
+		uasm_i_lui(&p, K0, uasm_rel_hi((long)tlb_do_page_fault_0));
+		uasm_i_addiu(&p, K0, K0, uasm_rel_lo((long)tlb_do_page_fault_0));
+		uasm_i_jr(&p, K0);
+	} else
+#endif
+	uasm_i_j(&p, (unsigned long)tlb_do_page_fault_0 & 0x0fffffff);
+	uasm_i_nop(&p);
+
+	if (p >= (u32 *)handle_tlbl_end)
+		panic("TLB load handler fastpath space exceeded");
+
+	uasm_resolve_relocs(relocs, labels);
+	pr_debug("Wrote TLB load handler fastpath (%u instructions).\n",
+		 (unsigned int)(p - (u32 *)handle_tlbl));
+
+	dump_handler("r4000_tlb_load", handle_tlbl, handle_tlbl_end);
+}
+
+static void build_r4000_tlb_store_handler(void)
+{
+	u32 *p = (u32 *)msk_isa16_mode((ulong)handle_tlbs);
+	struct uasm_label *l = labels;
+	struct uasm_reloc *r = relocs;
+	struct work_registers wr;
+
+	memset(p, 0, handle_tlbs_end - (char *)p);
+	memset(labels, 0, sizeof(labels));
+	memset(relocs, 0, sizeof(relocs));
+
+	wr = build_r4000_tlbchange_handler_head(&p, &l, &r);
+	build_pte_writable(&p, &r, wr.r1, wr.r2, wr.r3, label_nopage_tlbs);
+	if (m4kc_tlbp_war())
+		build_tlb_probe_entry(&p);
+	build_make_write(&p, &r, wr.r1, wr.r2, wr.r3);
+	build_r4000_tlbchange_handler_tail(&p, &l, &r, wr.r1, wr.r2);
+
+#ifdef CONFIG_MIPS_HUGE_TLB_SUPPORT
+	/*
+	 * This is the entry point when
+	 * build_r4000_tlbchange_handler_head spots a huge page.
+	 */
+	uasm_l_tlb_huge_update(&l, p);
+	iPTE_LW(&p, wr.r1, wr.r2);
+	build_pte_writable(&p, &r, wr.r1, wr.r2, wr.r3, label_nopage_tlbs);
+	build_tlb_probe_entry(&p);
+	uasm_i_ori(&p, wr.r1, wr.r1,
+		   _PAGE_ACCESSED | _PAGE_MODIFIED | _PAGE_VALID | _PAGE_DIRTY);
+	build_huge_handler_tail(&p, &r, &l, wr.r1, wr.r2, 1);
+#endif
+
+	uasm_l_nopage_tlbs(&l, p);
+	if (IS_ENABLED(CONFIG_CPU_LOONGSON3_WORKAROUNDS))
+		uasm_i_sync(&p, 0);
+	build_restore_work_registers(&p);
+#ifdef CONFIG_CPU_MICROMIPS
+	if ((unsigned long)tlb_do_page_fault_1 & 1) {
+		uasm_i_lui(&p, K0, uasm_rel_hi((long)tlb_do_page_fault_1));
+		uasm_i_addiu(&p, K0, K0, uasm_rel_lo((long)tlb_do_page_fault_1));
+		uasm_i_jr(&p, K0);
+	} else
+#endif
+	uasm_i_j(&p, (unsigned long)tlb_do_page_fault_1 & 0x0fffffff);
+	uasm_i_nop(&p);
+
+	if (p >= (u32 *)handle_tlbs_end)
+		panic("TLB store handler fastpath space exceeded");
+
+	uasm_resolve_relocs(relocs, labels);
+	pr_debug("Wrote TLB store handler fastpath (%u instructions).\n",
+		 (unsigned int)(p - (u32 *)handle_tlbs));
+
+	dump_handler("r4000_tlb_store", handle_tlbs, handle_tlbs_end);
+}
+
+static void build_r4000_tlb_modify_handler(void)
+{
+	u32 *p = (u32 *)msk_isa16_mode((ulong)handle_tlbm);
+	struct uasm_label *l = labels;
+	struct uasm_reloc *r = relocs;
+	struct work_registers wr;
+
+	memset(p, 0, handle_tlbm_end - (char *)p);
+	memset(labels, 0, sizeof(labels));
+	memset(relocs, 0, sizeof(relocs));
+
+	wr = build_r4000_tlbchange_handler_head(&p, &l, &r);
+	build_pte_modifiable(&p, &r, wr.r1, wr.r2, wr.r3, label_nopage_tlbm);
+	if (m4kc_tlbp_war())
+		build_tlb_probe_entry(&p);
+	/* Present and writable bits set, set accessed and dirty bits. */
+	build_make_write(&p, &r, wr.r1, wr.r2, wr.r3);
+	build_r4000_tlbchange_handler_tail(&p, &l, &r, wr.r1, wr.r2);
+
+#ifdef CONFIG_MIPS_HUGE_TLB_SUPPORT
+	/*
+	 * This is the entry point when
+	 * build_r4000_tlbchange_handler_head spots a huge page.
+	 */
+	uasm_l_tlb_huge_update(&l, p);
+	iPTE_LW(&p, wr.r1, wr.r2);
+	build_pte_modifiable(&p, &r, wr.r1, wr.r2,  wr.r3, label_nopage_tlbm);
+	build_tlb_probe_entry(&p);
+	uasm_i_ori(&p, wr.r1, wr.r1,
+		   _PAGE_ACCESSED | _PAGE_MODIFIED | _PAGE_VALID | _PAGE_DIRTY);
+	build_huge_handler_tail(&p, &r, &l, wr.r1, wr.r2, 0);
+#endif
+
+	uasm_l_nopage_tlbm(&l, p);
+	if (IS_ENABLED(CONFIG_CPU_LOONGSON3_WORKAROUNDS))
+		uasm_i_sync(&p, 0);
+	build_restore_work_registers(&p);
+#ifdef CONFIG_CPU_MICROMIPS
+	if ((unsigned long)tlb_do_page_fault_1 & 1) {
+		uasm_i_lui(&p, K0, uasm_rel_hi((long)tlb_do_page_fault_1));
+		uasm_i_addiu(&p, K0, K0, uasm_rel_lo((long)tlb_do_page_fault_1));
+		uasm_i_jr(&p, K0);
+	} else
+#endif
+	uasm_i_j(&p, (unsigned long)tlb_do_page_fault_1 & 0x0fffffff);
+	uasm_i_nop(&p);
+
+	if (p >= (u32 *)handle_tlbm_end)
+		panic("TLB modify handler fastpath space exceeded");
+
+	uasm_resolve_relocs(relocs, labels);
+	pr_debug("Wrote TLB modify handler fastpath (%u instructions).\n",
+		 (unsigned int)(p - (u32 *)handle_tlbm));
+
+	dump_handler("r4000_tlb_modify", handle_tlbm, handle_tlbm_end);
+}
+
+static void flush_tlb_handlers(void)
+{
+	local_flush_icache_range((unsigned long)handle_tlbl,
+			   (unsigned long)handle_tlbl_end);
+	local_flush_icache_range((unsigned long)handle_tlbs,
+			   (unsigned long)handle_tlbs_end);
+	local_flush_icache_range((unsigned long)handle_tlbm,
+			   (unsigned long)handle_tlbm_end);
+	local_flush_icache_range((unsigned long)tlbmiss_handler_setup_pgd,
+			   (unsigned long)tlbmiss_handler_setup_pgd_end);
+}
+
+static void print_htw_config(void)
+{
+	unsigned long config;
+	unsigned int pwctl;
+	const int field = 2 * sizeof(unsigned long);
+
+	config = read_c0_pwfield();
+	pr_debug("PWField (0x%0*lx): GDI: 0x%02lx  UDI: 0x%02lx  MDI: 0x%02lx  PTI: 0x%02lx  PTEI: 0x%02lx\n",
+		field, config,
+		(config & MIPS_PWFIELD_GDI_MASK) >> MIPS_PWFIELD_GDI_SHIFT,
+		(config & MIPS_PWFIELD_UDI_MASK) >> MIPS_PWFIELD_UDI_SHIFT,
+		(config & MIPS_PWFIELD_MDI_MASK) >> MIPS_PWFIELD_MDI_SHIFT,
+		(config & MIPS_PWFIELD_PTI_MASK) >> MIPS_PWFIELD_PTI_SHIFT,
+		(config & MIPS_PWFIELD_PTEI_MASK) >> MIPS_PWFIELD_PTEI_SHIFT);
+
+	config = read_c0_pwsize();
+	pr_debug("PWSize  (0x%0*lx): PS: 0x%lx  GDW: 0x%02lx  UDW: 0x%02lx  MDW: 0x%02lx  PTW: 0x%02lx  PTEW: 0x%02lx\n",
+		field, config,
+		(config & MIPS_PWSIZE_PS_MASK) >> MIPS_PWSIZE_PS_SHIFT,
+		(config & MIPS_PWSIZE_GDW_MASK) >> MIPS_PWSIZE_GDW_SHIFT,
+		(config & MIPS_PWSIZE_UDW_MASK) >> MIPS_PWSIZE_UDW_SHIFT,
+		(config & MIPS_PWSIZE_MDW_MASK) >> MIPS_PWSIZE_MDW_SHIFT,
+		(config & MIPS_PWSIZE_PTW_MASK) >> MIPS_PWSIZE_PTW_SHIFT,
+		(config & MIPS_PWSIZE_PTEW_MASK) >> MIPS_PWSIZE_PTEW_SHIFT);
+
+	pwctl = read_c0_pwctl();
+	pr_debug("PWCtl   (0x%x): PWEn: 0x%x  XK: 0x%x  XS: 0x%x  XU: 0x%x  DPH: 0x%x  HugePg: 0x%x  Psn: 0x%x\n",
+		pwctl,
+		(pwctl & MIPS_PWCTL_PWEN_MASK) >> MIPS_PWCTL_PWEN_SHIFT,
+		(pwctl & MIPS_PWCTL_XK_MASK) >> MIPS_PWCTL_XK_SHIFT,
+		(pwctl & MIPS_PWCTL_XS_MASK) >> MIPS_PWCTL_XS_SHIFT,
+		(pwctl & MIPS_PWCTL_XU_MASK) >> MIPS_PWCTL_XU_SHIFT,
+		(pwctl & MIPS_PWCTL_DPH_MASK) >> MIPS_PWCTL_DPH_SHIFT,
+		(pwctl & MIPS_PWCTL_HUGEPG_MASK) >> MIPS_PWCTL_HUGEPG_SHIFT,
+		(pwctl & MIPS_PWCTL_PSN_MASK) >> MIPS_PWCTL_PSN_SHIFT);
+}
+
+static void config_htw_params(void)
+{
+	unsigned long pwfield, pwsize, ptei;
+	unsigned int config;
+
+	/*
+	 * We are using 2-level page tables, so we only need to
+	 * setup GDW and PTW appropriately. UDW and MDW will remain 0.
+	 * The default value of GDI/UDI/MDI/PTI is 0xc. It is illegal to
+	 * write values less than 0xc in these fields because the entire
+	 * write will be dropped. As a result of which, we must preserve
+	 * the original reset values and overwrite only what we really want.
+	 */
+
+	pwfield = read_c0_pwfield();
+	/* re-initialize the GDI field */
+	pwfield &= ~MIPS_PWFIELD_GDI_MASK;
+	pwfield |= PGDIR_SHIFT << MIPS_PWFIELD_GDI_SHIFT;
+	/* re-initialize the PTI field including the even/odd bit */
+	pwfield &= ~MIPS_PWFIELD_PTI_MASK;
+	pwfield |= PAGE_SHIFT << MIPS_PWFIELD_PTI_SHIFT;
+	if (CONFIG_PGTABLE_LEVELS >= 3) {
+		pwfield &= ~MIPS_PWFIELD_MDI_MASK;
+		pwfield |= PMD_SHIFT << MIPS_PWFIELD_MDI_SHIFT;
+	}
+	/* Set the PTEI right shift */
+	ptei = _PAGE_GLOBAL_SHIFT << MIPS_PWFIELD_PTEI_SHIFT;
+	pwfield |= ptei;
+	write_c0_pwfield(pwfield);
+	/* Check whether the PTEI value is supported */
+	back_to_back_c0_hazard();
+	pwfield = read_c0_pwfield();
+	if (((pwfield & MIPS_PWFIELD_PTEI_MASK) << MIPS_PWFIELD_PTEI_SHIFT)
+		!= ptei) {
+		pr_warn("Unsupported PTEI field value: 0x%lx. HTW will not be enabled",
+			ptei);
+		/*
+		 * Drop option to avoid HTW being enabled via another path
+		 * (eg htw_reset())
+		 */
+		current_cpu_data.options &= ~MIPS_CPU_HTW;
+		return;
+	}
+
+	pwsize = ilog2(PTRS_PER_PGD) << MIPS_PWSIZE_GDW_SHIFT;
+	pwsize |= ilog2(PTRS_PER_PTE) << MIPS_PWSIZE_PTW_SHIFT;
+	if (CONFIG_PGTABLE_LEVELS >= 3)
+		pwsize |= ilog2(PTRS_PER_PMD) << MIPS_PWSIZE_MDW_SHIFT;
+
+	/* Set pointer size to size of directory pointers */
+	if (IS_ENABLED(CONFIG_64BIT))
+		pwsize |= MIPS_PWSIZE_PS_MASK;
+	/* PTEs may be multiple pointers long (e.g. with XPA) */
+	pwsize |= ((PTE_T_LOG2 - PGD_T_LOG2) << MIPS_PWSIZE_PTEW_SHIFT)
+			& MIPS_PWSIZE_PTEW_MASK;
+
+	write_c0_pwsize(pwsize);
+
+	/* Make sure everything is set before we enable the HTW */
+	back_to_back_c0_hazard();
+
+	/*
+	 * Enable HTW (and only for XUSeg on 64-bit), and disable the rest of
+	 * the pwctl fields.
+	 */
+	config = 1 << MIPS_PWCTL_PWEN_SHIFT;
+	if (IS_ENABLED(CONFIG_64BIT))
+		config |= MIPS_PWCTL_XU_MASK;
+	write_c0_pwctl(config);
+	pr_info("Hardware Page Table Walker enabled\n");
+
+	print_htw_config();
+}
+
+static void config_xpa_params(void)
+{
+#ifdef CONFIG_XPA
+	unsigned int pagegrain;
+
+	if (mips_xpa_disabled) {
+		pr_info("Extended Physical Addressing (XPA) disabled\n");
+		return;
+	}
+
+	pagegrain = read_c0_pagegrain();
+	write_c0_pagegrain(pagegrain | PG_ELPA);
+	back_to_back_c0_hazard();
+	pagegrain = read_c0_pagegrain();
+
+	if (pagegrain & PG_ELPA)
+		pr_info("Extended Physical Addressing (XPA) enabled\n");
+	else
+		panic("Extended Physical Addressing (XPA) disabled");
+#endif
+}
+
+static void check_pabits(void)
+{
+	unsigned long entry;
+	unsigned pabits, fillbits;
+
+	if (!cpu_has_rixi || _PAGE_NO_EXEC == 0) {
+		/*
+		 * We'll only be making use of the fact that we can rotate bits
+		 * into the fill if the CPU supports RIXI, so don't bother
+		 * probing this for CPUs which don't.
+		 */
+		return;
+	}
+
+	write_c0_entrylo0(~0ul);
+	back_to_back_c0_hazard();
+	entry = read_c0_entrylo0();
+
+	/* clear all non-PFN bits */
+	entry &= ~((1 << MIPS_ENTRYLO_PFN_SHIFT) - 1);
+	entry &= ~(MIPS_ENTRYLO_RI | MIPS_ENTRYLO_XI);
+
+	/* find a lower bound on PABITS, and upper bound on fill bits */
+	pabits = fls_long(entry) + 6;
+	fillbits = max_t(int, (int)BITS_PER_LONG - pabits, 0);
+
+	/* minus the RI & XI bits */
+	fillbits -= min_t(unsigned, fillbits, 2);
+
+	if (fillbits >= ilog2(_PAGE_NO_EXEC))
+		fill_includes_sw_bits = true;
+
+	pr_debug("Entry* registers contain %u fill bits\n", fillbits);
+}
+
+void build_tlb_refill_handler(void)
+{
+	/*
+	 * The refill handler is generated per-CPU, multi-node systems
+	 * may have local storage for it. The other handlers are only
+	 * needed once.
+	 */
+	static int run_once = 0;
+
+	if (IS_ENABLED(CONFIG_XPA) && !cpu_has_rixi)
+		panic("Kernels supporting XPA currently require CPUs with RIXI");
+
+	output_pgtable_bits_defines();
+	check_pabits();
+
+#ifdef CONFIG_64BIT
+	check_for_high_segbits = current_cpu_data.vmbits > (PGDIR_SHIFT + PGD_TABLE_ORDER + PAGE_SHIFT - 3);
+#endif
+
+	if (cpu_has_3kex) {
+#ifndef CONFIG_MIPS_PGD_C0_CONTEXT
+		if (!run_once) {
+			build_setup_pgd();
+			build_r3000_tlb_refill_handler();
+			build_r3000_tlb_load_handler();
+			build_r3000_tlb_store_handler();
+			build_r3000_tlb_modify_handler();
+			flush_tlb_handlers();
+			run_once++;
+		}
+#else
+		panic("No R3000 TLB refill handler");
+#endif
+		return;
+	}
+
+	if (cpu_has_ldpte)
+		setup_pw();
+
+	if (!run_once) {
+		scratch_reg = allocate_kscratch();
+		build_setup_pgd();
+		build_r4000_tlb_load_handler();
+		build_r4000_tlb_store_handler();
+		build_r4000_tlb_modify_handler();
+		if (cpu_has_ldpte)
+			build_loongson3_tlb_refill_handler();
+		else
+			build_r4000_tlb_refill_handler();
+		flush_tlb_handlers();
+		run_once++;
+	}
+	if (cpu_has_xpa)
+		config_xpa_params();
+	if (cpu_has_htw)
+		config_htw_params();
+}
diff --git a/arch/mips/mm/uasm-micromips.c b/arch/mips/mm/uasm-micromips.c
new file mode 100644
index 000000000..75ef90486
--- /dev/null
+++ b/arch/mips/mm/uasm-micromips.c
@@ -0,0 +1,232 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * A small micro-assembler. It is intentionally kept simple, does only
+ * support a subset of instructions, and does not try to hide pipeline
+ * effects like branch delay slots.
+ *
+ * Copyright (C) 2004, 2005, 2006, 2008	 Thiemo Seufer
+ * Copyright (C) 2005, 2007  Maciej W. Rozycki
+ * Copyright (C) 2006  Ralf Baechle (ralf@linux-mips.org)
+ * Copyright (C) 2012, 2013   MIPS Technologies, Inc.  All rights reserved.
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+
+#include <asm/inst.h>
+#include <asm/elf.h>
+#include <asm/bugs.h>
+#include <asm/uasm.h>
+
+#define RS_MASK		0x1f
+#define RS_SH		16
+#define RT_MASK		0x1f
+#define RT_SH		21
+#define SCIMM_MASK	0x3ff
+#define SCIMM_SH	16
+
+/* This macro sets the non-variable bits of an instruction. */
+#define M(a, b, c, d, e, f)					\
+	((a) << OP_SH						\
+	 | (b) << RT_SH						\
+	 | (c) << RS_SH						\
+	 | (d) << RD_SH						\
+	 | (e) << RE_SH						\
+	 | (f) << FUNC_SH)
+
+#include "uasm.c"
+
+static const struct insn insn_table_MM[insn_invalid] = {
+	[insn_addu]	= {M(mm_pool32a_op, 0, 0, 0, 0, mm_addu32_op), RT | RS | RD},
+	[insn_addiu]	= {M(mm_addiu32_op, 0, 0, 0, 0, 0), RT | RS | SIMM},
+	[insn_and]	= {M(mm_pool32a_op, 0, 0, 0, 0, mm_and_op), RT | RS | RD},
+	[insn_andi]	= {M(mm_andi32_op, 0, 0, 0, 0, 0), RT | RS | UIMM},
+	[insn_beq]	= {M(mm_beq32_op, 0, 0, 0, 0, 0), RS | RT | BIMM},
+	[insn_beql]	= {0, 0},
+	[insn_bgez]	= {M(mm_pool32i_op, mm_bgez_op, 0, 0, 0, 0), RS | BIMM},
+	[insn_bgezl]	= {0, 0},
+	[insn_bltz]	= {M(mm_pool32i_op, mm_bltz_op, 0, 0, 0, 0), RS | BIMM},
+	[insn_bltzl]	= {0, 0},
+	[insn_bne]	= {M(mm_bne32_op, 0, 0, 0, 0, 0), RT | RS | BIMM},
+	[insn_cache]	= {M(mm_pool32b_op, 0, 0, mm_cache_func, 0, 0), RT | RS | SIMM},
+	[insn_cfc1]	= {M(mm_pool32f_op, 0, 0, 0, mm_cfc1_op, mm_32f_73_op), RT | RS},
+	[insn_cfcmsa]	= {M(mm_pool32s_op, 0, msa_cfc_op, 0, 0, mm_32s_elm_op), RD | RE},
+	[insn_ctc1]	= {M(mm_pool32f_op, 0, 0, 0, mm_ctc1_op, mm_32f_73_op), RT | RS},
+	[insn_ctcmsa]	= {M(mm_pool32s_op, 0, msa_ctc_op, 0, 0, mm_32s_elm_op), RD | RE},
+	[insn_daddu]	= {0, 0},
+	[insn_daddiu]	= {0, 0},
+	[insn_di]	= {M(mm_pool32a_op, 0, 0, 0, mm_di_op, mm_pool32axf_op), RS},
+	[insn_divu]	= {M(mm_pool32a_op, 0, 0, 0, mm_divu_op, mm_pool32axf_op), RT | RS},
+	[insn_dmfc0]	= {0, 0},
+	[insn_dmtc0]	= {0, 0},
+	[insn_dsll]	= {0, 0},
+	[insn_dsll32]	= {0, 0},
+	[insn_dsra]	= {0, 0},
+	[insn_dsrl]	= {0, 0},
+	[insn_dsrl32]	= {0, 0},
+	[insn_drotr]	= {0, 0},
+	[insn_drotr32]	= {0, 0},
+	[insn_dsubu]	= {0, 0},
+	[insn_eret]	= {M(mm_pool32a_op, 0, 0, 0, mm_eret_op, mm_pool32axf_op), 0},
+	[insn_ins]	= {M(mm_pool32a_op, 0, 0, 0, 0, mm_ins_op), RT | RS | RD | RE},
+	[insn_ext]	= {M(mm_pool32a_op, 0, 0, 0, 0, mm_ext_op), RT | RS | RD | RE},
+	[insn_j]	= {M(mm_j32_op, 0, 0, 0, 0, 0), JIMM},
+	[insn_jal]	= {M(mm_jal32_op, 0, 0, 0, 0, 0), JIMM},
+	[insn_jalr]	= {M(mm_pool32a_op, 0, 0, 0, mm_jalr_op, mm_pool32axf_op), RT | RS},
+	[insn_jr]	= {M(mm_pool32a_op, 0, 0, 0, mm_jalr_op, mm_pool32axf_op), RS},
+	[insn_lb]	= {M(mm_lb32_op, 0, 0, 0, 0, 0), RT | RS | SIMM},
+	[insn_ld]	= {0, 0},
+	[insn_lh]	= {M(mm_lh32_op, 0, 0, 0, 0, 0), RT | RS | SIMM},
+	[insn_ll]	= {M(mm_pool32c_op, 0, 0, (mm_ll_func << 1), 0, 0), RS | RT | SIMM},
+	[insn_lld]	= {0, 0},
+	[insn_lui]	= {M(mm_pool32i_op, mm_lui_op, 0, 0, 0, 0), RS | SIMM},
+	[insn_lw]	= {M(mm_lw32_op, 0, 0, 0, 0, 0), RT | RS | SIMM},
+	[insn_mfc0]	= {M(mm_pool32a_op, 0, 0, 0, mm_mfc0_op, mm_pool32axf_op), RT | RS | RD},
+	[insn_mfhi]	= {M(mm_pool32a_op, 0, 0, 0, mm_mfhi32_op, mm_pool32axf_op), RS},
+	[insn_mflo]	= {M(mm_pool32a_op, 0, 0, 0, mm_mflo32_op, mm_pool32axf_op), RS},
+	[insn_mtc0]	= {M(mm_pool32a_op, 0, 0, 0, mm_mtc0_op, mm_pool32axf_op), RT | RS | RD},
+	[insn_mthi]	= {M(mm_pool32a_op, 0, 0, 0, mm_mthi32_op, mm_pool32axf_op), RS},
+	[insn_mtlo]	= {M(mm_pool32a_op, 0, 0, 0, mm_mtlo32_op, mm_pool32axf_op), RS},
+	[insn_mul]	= {M(mm_pool32a_op, 0, 0, 0, 0, mm_mul_op), RT | RS | RD},
+	[insn_or]	= {M(mm_pool32a_op, 0, 0, 0, 0, mm_or32_op), RT | RS | RD},
+	[insn_ori]	= {M(mm_ori32_op, 0, 0, 0, 0, 0), RT | RS | UIMM},
+	[insn_pref]	= {M(mm_pool32c_op, 0, 0, (mm_pref_func << 1), 0, 0), RT | RS | SIMM},
+	[insn_rfe]	= {0, 0},
+	[insn_sc]	= {M(mm_pool32c_op, 0, 0, (mm_sc_func << 1), 0, 0), RT | RS | SIMM},
+	[insn_scd]	= {0, 0},
+	[insn_sd]	= {0, 0},
+	[insn_sll]	= {M(mm_pool32a_op, 0, 0, 0, 0, mm_sll32_op), RT | RS | RD},
+	[insn_sllv]	= {M(mm_pool32a_op, 0, 0, 0, 0, mm_sllv32_op), RT | RS | RD},
+	[insn_slt]	= {M(mm_pool32a_op, 0, 0, 0, 0, mm_slt_op), RT | RS | RD},
+	[insn_sltiu]	= {M(mm_sltiu32_op, 0, 0, 0, 0, 0), RT | RS | SIMM},
+	[insn_sltu]	= {M(mm_pool32a_op, 0, 0, 0, 0, mm_sltu_op), RT | RS | RD},
+	[insn_sra]	= {M(mm_pool32a_op, 0, 0, 0, 0, mm_sra_op), RT | RS | RD},
+	[insn_srav]	= {M(mm_pool32a_op, 0, 0, 0, 0, mm_srav_op), RT | RS | RD},
+	[insn_srl]	= {M(mm_pool32a_op, 0, 0, 0, 0, mm_srl32_op), RT | RS | RD},
+	[insn_srlv]	= {M(mm_pool32a_op, 0, 0, 0, 0, mm_srlv32_op), RT | RS | RD},
+	[insn_rotr]	= {M(mm_pool32a_op, 0, 0, 0, 0, mm_rotr_op), RT | RS | RD},
+	[insn_subu]	= {M(mm_pool32a_op, 0, 0, 0, 0, mm_subu32_op), RT | RS | RD},
+	[insn_sw]	= {M(mm_sw32_op, 0, 0, 0, 0, 0), RT | RS | SIMM},
+	[insn_sync]	= {M(mm_pool32a_op, 0, 0, 0, mm_sync_op, mm_pool32axf_op), RS},
+	[insn_tlbp]	= {M(mm_pool32a_op, 0, 0, 0, mm_tlbp_op, mm_pool32axf_op), 0},
+	[insn_tlbr]	= {M(mm_pool32a_op, 0, 0, 0, mm_tlbr_op, mm_pool32axf_op), 0},
+	[insn_tlbwi]	= {M(mm_pool32a_op, 0, 0, 0, mm_tlbwi_op, mm_pool32axf_op), 0},
+	[insn_tlbwr]	= {M(mm_pool32a_op, 0, 0, 0, mm_tlbwr_op, mm_pool32axf_op), 0},
+	[insn_wait]	= {M(mm_pool32a_op, 0, 0, 0, mm_wait_op, mm_pool32axf_op), SCIMM},
+	[insn_wsbh]	= {M(mm_pool32a_op, 0, 0, 0, mm_wsbh_op, mm_pool32axf_op), RT | RS},
+	[insn_xor]	= {M(mm_pool32a_op, 0, 0, 0, 0, mm_xor32_op), RT | RS | RD},
+	[insn_xori]	= {M(mm_xori32_op, 0, 0, 0, 0, 0), RT | RS | UIMM},
+	[insn_dins]	= {0, 0},
+	[insn_dinsm]	= {0, 0},
+	[insn_syscall]	= {M(mm_pool32a_op, 0, 0, 0, mm_syscall_op, mm_pool32axf_op), SCIMM},
+	[insn_bbit0]	= {0, 0},
+	[insn_bbit1]	= {0, 0},
+	[insn_lwx]	= {0, 0},
+	[insn_ldx]	= {0, 0},
+};
+
+#undef M
+
+static inline u32 build_bimm(s32 arg)
+{
+	WARN(arg > 0xffff || arg < -0x10000,
+	     KERN_WARNING "Micro-assembler field overflow\n");
+
+	WARN(arg & 0x3, KERN_WARNING "Invalid micro-assembler branch target\n");
+
+	return ((arg < 0) ? (1 << 15) : 0) | ((arg >> 1) & 0x7fff);
+}
+
+static inline u32 build_jimm(u32 arg)
+{
+
+	WARN(arg & ~((JIMM_MASK << 2) | 1),
+	     KERN_WARNING "Micro-assembler field overflow\n");
+
+	return (arg >> 1) & JIMM_MASK;
+}
+
+/*
+ * The order of opcode arguments is implicitly left to right,
+ * starting with RS and ending with FUNC or IMM.
+ */
+static void build_insn(u32 **buf, enum opcode opc, ...)
+{
+	const struct insn *ip;
+	va_list ap;
+	u32 op;
+
+	if (opc < 0 || opc >= insn_invalid ||
+	    (opc == insn_daddiu && r4k_daddiu_bug()) ||
+	    (insn_table_MM[opc].match == 0 && insn_table_MM[opc].fields == 0))
+		panic("Unsupported Micro-assembler instruction %d", opc);
+
+	ip = &insn_table_MM[opc];
+
+	op = ip->match;
+	va_start(ap, opc);
+	if (ip->fields & RS) {
+		if (opc == insn_mfc0 || opc == insn_mtc0 ||
+		    opc == insn_cfc1 || opc == insn_ctc1)
+			op |= build_rt(va_arg(ap, u32));
+		else
+			op |= build_rs(va_arg(ap, u32));
+	}
+	if (ip->fields & RT) {
+		if (opc == insn_mfc0 || opc == insn_mtc0 ||
+		    opc == insn_cfc1 || opc == insn_ctc1)
+			op |= build_rs(va_arg(ap, u32));
+		else
+			op |= build_rt(va_arg(ap, u32));
+	}
+	if (ip->fields & RD)
+		op |= build_rd(va_arg(ap, u32));
+	if (ip->fields & RE)
+		op |= build_re(va_arg(ap, u32));
+	if (ip->fields & SIMM)
+		op |= build_simm(va_arg(ap, s32));
+	if (ip->fields & UIMM)
+		op |= build_uimm(va_arg(ap, u32));
+	if (ip->fields & BIMM)
+		op |= build_bimm(va_arg(ap, s32));
+	if (ip->fields & JIMM)
+		op |= build_jimm(va_arg(ap, u32));
+	if (ip->fields & FUNC)
+		op |= build_func(va_arg(ap, u32));
+	if (ip->fields & SET)
+		op |= build_set(va_arg(ap, u32));
+	if (ip->fields & SCIMM)
+		op |= build_scimm(va_arg(ap, u32));
+	va_end(ap);
+
+#ifdef CONFIG_CPU_LITTLE_ENDIAN
+	**buf = ((op & 0xffff) << 16) | (op >> 16);
+#else
+	**buf = op;
+#endif
+	(*buf)++;
+}
+
+static inline void
+__resolve_relocs(struct uasm_reloc *rel, struct uasm_label *lab)
+{
+	long laddr = (long)lab->addr;
+	long raddr = (long)rel->addr;
+
+	switch (rel->type) {
+	case R_MIPS_PC16:
+#ifdef CONFIG_CPU_LITTLE_ENDIAN
+		*rel->addr |= (build_bimm(laddr - (raddr + 4)) << 16);
+#else
+		*rel->addr |= build_bimm(laddr - (raddr + 4));
+#endif
+		break;
+
+	default:
+		panic("Unsupported Micro-assembler relocation %d",
+		      rel->type);
+	}
+}
diff --git a/arch/mips/mm/uasm-mips.c b/arch/mips/mm/uasm-mips.c
new file mode 100644
index 000000000..e15c6700c
--- /dev/null
+++ b/arch/mips/mm/uasm-mips.c
@@ -0,0 +1,292 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * A small micro-assembler. It is intentionally kept simple, does only
+ * support a subset of instructions, and does not try to hide pipeline
+ * effects like branch delay slots.
+ *
+ * Copyright (C) 2004, 2005, 2006, 2008	 Thiemo Seufer
+ * Copyright (C) 2005, 2007  Maciej W. Rozycki
+ * Copyright (C) 2006  Ralf Baechle (ralf@linux-mips.org)
+ * Copyright (C) 2012, 2013  MIPS Technologies, Inc.  All rights reserved.
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+
+#include <asm/inst.h>
+#include <asm/elf.h>
+#include <asm/bugs.h>
+#include <asm/uasm.h>
+
+#define RS_MASK		0x1f
+#define RS_SH		21
+#define RT_MASK		0x1f
+#define RT_SH		16
+#define SCIMM_MASK	0xfffff
+#define SCIMM_SH	6
+
+/* This macro sets the non-variable bits of an instruction. */
+#define M(a, b, c, d, e, f)					\
+	((a) << OP_SH						\
+	 | (b) << RS_SH						\
+	 | (c) << RT_SH						\
+	 | (d) << RD_SH						\
+	 | (e) << RE_SH						\
+	 | (f) << FUNC_SH)
+
+/* This macro sets the non-variable bits of an R6 instruction. */
+#define M6(a, b, c, d, e)					\
+	((a) << OP_SH						\
+	 | (b) << RS_SH						\
+	 | (c) << RT_SH						\
+	 | (d) << SIMM9_SH					\
+	 | (e) << FUNC_SH)
+
+#include "uasm.c"
+
+static const struct insn insn_table[insn_invalid] = {
+	[insn_addiu]	= {M(addiu_op, 0, 0, 0, 0, 0), RS | RT | SIMM},
+	[insn_addu]	= {M(spec_op, 0, 0, 0, 0, addu_op), RS | RT | RD},
+	[insn_and]	= {M(spec_op, 0, 0, 0, 0, and_op), RS | RT | RD},
+	[insn_andi]	= {M(andi_op, 0, 0, 0, 0, 0), RS | RT | UIMM},
+	[insn_bbit0]	= {M(lwc2_op, 0, 0, 0, 0, 0), RS | RT | BIMM},
+	[insn_bbit1]	= {M(swc2_op, 0, 0, 0, 0, 0), RS | RT | BIMM},
+	[insn_beq]	= {M(beq_op, 0, 0, 0, 0, 0), RS | RT | BIMM},
+	[insn_beql]	= {M(beql_op, 0, 0, 0, 0, 0), RS | RT | BIMM},
+	[insn_bgez]	= {M(bcond_op, 0, bgez_op, 0, 0, 0), RS | BIMM},
+	[insn_bgezl]	= {M(bcond_op, 0, bgezl_op, 0, 0, 0), RS | BIMM},
+	[insn_bgtz]	= {M(bgtz_op, 0, 0, 0, 0, 0), RS | BIMM},
+	[insn_blez]	= {M(blez_op, 0, 0, 0, 0, 0), RS | BIMM},
+	[insn_bltz]	= {M(bcond_op, 0, bltz_op, 0, 0, 0), RS | BIMM},
+	[insn_bltzl]	= {M(bcond_op, 0, bltzl_op, 0, 0, 0), RS | BIMM},
+	[insn_bne]	= {M(bne_op, 0, 0, 0, 0, 0), RS | RT | BIMM},
+	[insn_break]	= {M(spec_op, 0, 0, 0, 0, break_op), SCIMM},
+#ifndef CONFIG_CPU_MIPSR6
+	[insn_cache]	= {M(cache_op, 0, 0, 0, 0, 0),  RS | RT | SIMM},
+#else
+	[insn_cache]	= {M6(spec3_op, 0, 0, 0, cache6_op),  RS | RT | SIMM9},
+#endif
+	[insn_cfc1]	= {M(cop1_op, cfc_op, 0, 0, 0, 0), RT | RD},
+	[insn_cfcmsa]	= {M(msa_op, 0, msa_cfc_op, 0, 0, msa_elm_op), RD | RE},
+	[insn_ctc1]	= {M(cop1_op, ctc_op, 0, 0, 0, 0), RT | RD},
+	[insn_ctcmsa]	= {M(msa_op, 0, msa_ctc_op, 0, 0, msa_elm_op), RD | RE},
+	[insn_daddiu]	= {M(daddiu_op, 0, 0, 0, 0, 0), RS | RT | SIMM},
+	[insn_daddu]	= {M(spec_op, 0, 0, 0, 0, daddu_op), RS | RT | RD},
+	[insn_ddivu]	= {M(spec_op, 0, 0, 0, 0, ddivu_op), RS | RT},
+	[insn_ddivu_r6]	= {M(spec_op, 0, 0, 0, ddivu_ddivu6_op, ddivu_op),
+				RS | RT | RD},
+	[insn_di]	= {M(cop0_op, mfmc0_op, 0, 12, 0, 0), RT},
+	[insn_dins]	= {M(spec3_op, 0, 0, 0, 0, dins_op), RS | RT | RD | RE},
+	[insn_dinsm]	= {M(spec3_op, 0, 0, 0, 0, dinsm_op), RS | RT | RD | RE},
+	[insn_dinsu]	= {M(spec3_op, 0, 0, 0, 0, dinsu_op), RS | RT | RD | RE},
+	[insn_divu]	= {M(spec_op, 0, 0, 0, 0, divu_op), RS | RT},
+	[insn_divu_r6]	= {M(spec_op, 0, 0, 0, divu_divu6_op, divu_op),
+				RS | RT | RD},
+	[insn_dmfc0]	= {M(cop0_op, dmfc_op, 0, 0, 0, 0), RT | RD | SET},
+	[insn_dmodu]	= {M(spec_op, 0, 0, 0, ddivu_dmodu_op, ddivu_op),
+				RS | RT | RD},
+	[insn_dmtc0]	= {M(cop0_op, dmtc_op, 0, 0, 0, 0), RT | RD | SET},
+	[insn_dmultu]	= {M(spec_op, 0, 0, 0, 0, dmultu_op), RS | RT},
+	[insn_dmulu]	= {M(spec_op, 0, 0, 0, dmultu_dmulu_op, dmultu_op),
+				RS | RT | RD},
+	[insn_drotr]	= {M(spec_op, 1, 0, 0, 0, dsrl_op), RT | RD | RE},
+	[insn_drotr32]	= {M(spec_op, 1, 0, 0, 0, dsrl32_op), RT | RD | RE},
+	[insn_dsbh]	= {M(spec3_op, 0, 0, 0, dsbh_op, dbshfl_op), RT | RD},
+	[insn_dshd]	= {M(spec3_op, 0, 0, 0, dshd_op, dbshfl_op), RT | RD},
+	[insn_dsll]	= {M(spec_op, 0, 0, 0, 0, dsll_op), RT | RD | RE},
+	[insn_dsll32]	= {M(spec_op, 0, 0, 0, 0, dsll32_op), RT | RD | RE},
+	[insn_dsllv]	= {M(spec_op, 0, 0, 0, 0, dsllv_op),  RS | RT | RD},
+	[insn_dsra]	= {M(spec_op, 0, 0, 0, 0, dsra_op), RT | RD | RE},
+	[insn_dsra32]	= {M(spec_op, 0, 0, 0, 0, dsra32_op), RT | RD | RE},
+	[insn_dsrav]	= {M(spec_op, 0, 0, 0, 0, dsrav_op),  RS | RT | RD},
+	[insn_dsrl]	= {M(spec_op, 0, 0, 0, 0, dsrl_op), RT | RD | RE},
+	[insn_dsrl32]	= {M(spec_op, 0, 0, 0, 0, dsrl32_op), RT | RD | RE},
+	[insn_dsrlv]	= {M(spec_op, 0, 0, 0, 0, dsrlv_op),  RS | RT | RD},
+	[insn_dsubu]	= {M(spec_op, 0, 0, 0, 0, dsubu_op), RS | RT | RD},
+	[insn_eret]	= {M(cop0_op, cop_op, 0, 0, 0, eret_op),  0},
+	[insn_ext]	= {M(spec3_op, 0, 0, 0, 0, ext_op), RS | RT | RD | RE},
+	[insn_ins]	= {M(spec3_op, 0, 0, 0, 0, ins_op), RS | RT | RD | RE},
+	[insn_j]	= {M(j_op, 0, 0, 0, 0, 0),  JIMM},
+	[insn_jal]	= {M(jal_op, 0, 0, 0, 0, 0),	JIMM},
+	[insn_jalr]	= {M(spec_op, 0, 0, 0, 0, jalr_op), RS | RD},
+#ifndef CONFIG_CPU_MIPSR6
+	[insn_jr]	= {M(spec_op, 0, 0, 0, 0, jr_op),  RS},
+#else
+	[insn_jr]	= {M(spec_op, 0, 0, 0, 0, jalr_op),  RS},
+#endif
+	[insn_lb]	= {M(lb_op, 0, 0, 0, 0, 0), RS | RT | SIMM},
+	[insn_lbu]	= {M(lbu_op, 0, 0, 0, 0, 0), RS | RT | SIMM},
+	[insn_ld]	= {M(ld_op, 0, 0, 0, 0, 0),  RS | RT | SIMM},
+	[insn_lddir]	= {M(lwc2_op, 0, 0, 0, lddir_op, mult_op), RS | RT | RD},
+	[insn_ldpte]	= {M(lwc2_op, 0, 0, 0, ldpte_op, mult_op), RS | RD},
+	[insn_ldx]	= {M(spec3_op, 0, 0, 0, ldx_op, lx_op), RS | RT | RD},
+	[insn_lh]	= {M(lh_op, 0, 0, 0, 0, 0),  RS | RT | SIMM},
+	[insn_lhu]	= {M(lhu_op, 0, 0, 0, 0, 0),  RS | RT | SIMM},
+#ifndef CONFIG_CPU_MIPSR6
+	[insn_ll]	= {M(ll_op, 0, 0, 0, 0, 0),  RS | RT | SIMM},
+	[insn_lld]	= {M(lld_op, 0, 0, 0, 0, 0),	RS | RT | SIMM},
+#else
+	[insn_ll]	= {M6(spec3_op, 0, 0, 0, ll6_op),  RS | RT | SIMM9},
+	[insn_lld]	= {M6(spec3_op, 0, 0, 0, lld6_op),  RS | RT | SIMM9},
+#endif
+	[insn_lui]	= {M(lui_op, 0, 0, 0, 0, 0),	RT | SIMM},
+	[insn_lw]	= {M(lw_op, 0, 0, 0, 0, 0),  RS | RT | SIMM},
+	[insn_lwu]	= {M(lwu_op, 0, 0, 0, 0, 0),  RS | RT | SIMM},
+	[insn_lwx]	= {M(spec3_op, 0, 0, 0, lwx_op, lx_op), RS | RT | RD},
+	[insn_mfc0]	= {M(cop0_op, mfc_op, 0, 0, 0, 0),  RT | RD | SET},
+	[insn_mfhc0]	= {M(cop0_op, mfhc0_op, 0, 0, 0, 0),  RT | RD | SET},
+	[insn_mfhi]	= {M(spec_op, 0, 0, 0, 0, mfhi_op), RD},
+	[insn_mflo]	= {M(spec_op, 0, 0, 0, 0, mflo_op), RD},
+	[insn_modu]	= {M(spec_op, 0, 0, 0, divu_modu_op, divu_op),
+				RS | RT | RD},
+	[insn_movn]	= {M(spec_op, 0, 0, 0, 0, movn_op), RS | RT | RD},
+	[insn_movz]	= {M(spec_op, 0, 0, 0, 0, movz_op), RS | RT | RD},
+	[insn_mtc0]	= {M(cop0_op, mtc_op, 0, 0, 0, 0),  RT | RD | SET},
+	[insn_mthc0]	= {M(cop0_op, mthc0_op, 0, 0, 0, 0),  RT | RD | SET},
+	[insn_mthi]	= {M(spec_op, 0, 0, 0, 0, mthi_op), RS},
+	[insn_mtlo]	= {M(spec_op, 0, 0, 0, 0, mtlo_op), RS},
+	[insn_mulu]	= {M(spec_op, 0, 0, 0, multu_mulu_op, multu_op),
+				RS | RT | RD},
+	[insn_muhu]	= {M(spec_op, 0, 0, 0, multu_muhu_op, multu_op),
+				RS | RT | RD},
+#ifndef CONFIG_CPU_MIPSR6
+	[insn_mul]	= {M(spec2_op, 0, 0, 0, 0, mul_op), RS | RT | RD},
+#else
+	[insn_mul]	= {M(spec_op, 0, 0, 0, mult_mul_op, mult_op), RS | RT | RD},
+#endif
+	[insn_multu]	= {M(spec_op, 0, 0, 0, 0, multu_op), RS | RT},
+	[insn_nor]	= {M(spec_op, 0, 0, 0, 0, nor_op),  RS | RT | RD},
+	[insn_or]	= {M(spec_op, 0, 0, 0, 0, or_op),  RS | RT | RD},
+	[insn_ori]	= {M(ori_op, 0, 0, 0, 0, 0),	RS | RT | UIMM},
+#ifndef CONFIG_CPU_MIPSR6
+	[insn_pref]	= {M(pref_op, 0, 0, 0, 0, 0),  RS | RT | SIMM},
+#else
+	[insn_pref]	= {M6(spec3_op, 0, 0, 0, pref6_op),  RS | RT | SIMM9},
+#endif
+	[insn_rfe]	= {M(cop0_op, cop_op, 0, 0, 0, rfe_op),  0},
+	[insn_rotr]	= {M(spec_op, 1, 0, 0, 0, srl_op),  RT | RD | RE},
+	[insn_sb]	= {M(sb_op, 0, 0, 0, 0, 0),  RS | RT | SIMM},
+#ifndef CONFIG_CPU_MIPSR6
+	[insn_sc]	= {M(sc_op, 0, 0, 0, 0, 0),  RS | RT | SIMM},
+	[insn_scd]	= {M(scd_op, 0, 0, 0, 0, 0),	RS | RT | SIMM},
+#else
+	[insn_sc]	= {M6(spec3_op, 0, 0, 0, sc6_op),  RS | RT | SIMM9},
+	[insn_scd]	= {M6(spec3_op, 0, 0, 0, scd6_op),  RS | RT | SIMM9},
+#endif
+	[insn_sd]	= {M(sd_op, 0, 0, 0, 0, 0),  RS | RT | SIMM},
+	[insn_seleqz]	= {M(spec_op, 0, 0, 0, 0, seleqz_op), RS | RT | RD},
+	[insn_selnez]	= {M(spec_op, 0, 0, 0, 0, selnez_op), RS | RT | RD},
+	[insn_sh]	= {M(sh_op, 0, 0, 0, 0, 0),  RS | RT | SIMM},
+	[insn_sll]	= {M(spec_op, 0, 0, 0, 0, sll_op),  RT | RD | RE},
+	[insn_sllv]	= {M(spec_op, 0, 0, 0, 0, sllv_op),  RS | RT | RD},
+	[insn_slt]	= {M(spec_op, 0, 0, 0, 0, slt_op),  RS | RT | RD},
+	[insn_slti]	= {M(slti_op, 0, 0, 0, 0, 0), RS | RT | SIMM},
+	[insn_sltiu]	= {M(sltiu_op, 0, 0, 0, 0, 0), RS | RT | SIMM},
+	[insn_sltu]	= {M(spec_op, 0, 0, 0, 0, sltu_op), RS | RT | RD},
+	[insn_sra]	= {M(spec_op, 0, 0, 0, 0, sra_op),  RT | RD | RE},
+	[insn_srav]	= {M(spec_op, 0, 0, 0, 0, srav_op), RS | RT | RD},
+	[insn_srl]	= {M(spec_op, 0, 0, 0, 0, srl_op),  RT | RD | RE},
+	[insn_srlv]	= {M(spec_op, 0, 0, 0, 0, srlv_op),  RS | RT | RD},
+	[insn_subu]	= {M(spec_op, 0, 0, 0, 0, subu_op),	RS | RT | RD},
+	[insn_sw]	= {M(sw_op, 0, 0, 0, 0, 0),  RS | RT | SIMM},
+	[insn_sync]	= {M(spec_op, 0, 0, 0, 0, sync_op), RE},
+	[insn_syscall]	= {M(spec_op, 0, 0, 0, 0, syscall_op), SCIMM},
+	[insn_tlbp]	= {M(cop0_op, cop_op, 0, 0, 0, tlbp_op),  0},
+	[insn_tlbr]	= {M(cop0_op, cop_op, 0, 0, 0, tlbr_op),  0},
+	[insn_tlbwi]	= {M(cop0_op, cop_op, 0, 0, 0, tlbwi_op),  0},
+	[insn_tlbwr]	= {M(cop0_op, cop_op, 0, 0, 0, tlbwr_op),  0},
+	[insn_wait]	= {M(cop0_op, cop_op, 0, 0, 0, wait_op), SCIMM},
+	[insn_wsbh]	= {M(spec3_op, 0, 0, 0, wsbh_op, bshfl_op), RT | RD},
+	[insn_xor]	= {M(spec_op, 0, 0, 0, 0, xor_op),  RS | RT | RD},
+	[insn_xori]	= {M(xori_op, 0, 0, 0, 0, 0),  RS | RT | UIMM},
+	[insn_yield]	= {M(spec3_op, 0, 0, 0, 0, yield_op), RS | RD},
+};
+
+#undef M
+
+static inline u32 build_bimm(s32 arg)
+{
+	WARN(arg > 0x1ffff || arg < -0x20000,
+	     KERN_WARNING "Micro-assembler field overflow\n");
+
+	WARN(arg & 0x3, KERN_WARNING "Invalid micro-assembler branch target\n");
+
+	return ((arg < 0) ? (1 << 15) : 0) | ((arg >> 2) & 0x7fff);
+}
+
+static inline u32 build_jimm(u32 arg)
+{
+	WARN(arg & ~(JIMM_MASK << 2),
+	     KERN_WARNING "Micro-assembler field overflow\n");
+
+	return (arg >> 2) & JIMM_MASK;
+}
+
+/*
+ * The order of opcode arguments is implicitly left to right,
+ * starting with RS and ending with FUNC or IMM.
+ */
+static void build_insn(u32 **buf, enum opcode opc, ...)
+{
+	const struct insn *ip;
+	va_list ap;
+	u32 op;
+
+	if (opc < 0 || opc >= insn_invalid ||
+	    (opc == insn_daddiu && r4k_daddiu_bug()) ||
+	    (insn_table[opc].match == 0 && insn_table[opc].fields == 0))
+		panic("Unsupported Micro-assembler instruction %d", opc);
+
+	ip = &insn_table[opc];
+
+	op = ip->match;
+	va_start(ap, opc);
+	if (ip->fields & RS)
+		op |= build_rs(va_arg(ap, u32));
+	if (ip->fields & RT)
+		op |= build_rt(va_arg(ap, u32));
+	if (ip->fields & RD)
+		op |= build_rd(va_arg(ap, u32));
+	if (ip->fields & RE)
+		op |= build_re(va_arg(ap, u32));
+	if (ip->fields & SIMM)
+		op |= build_simm(va_arg(ap, s32));
+	if (ip->fields & UIMM)
+		op |= build_uimm(va_arg(ap, u32));
+	if (ip->fields & BIMM)
+		op |= build_bimm(va_arg(ap, s32));
+	if (ip->fields & JIMM)
+		op |= build_jimm(va_arg(ap, u32));
+	if (ip->fields & FUNC)
+		op |= build_func(va_arg(ap, u32));
+	if (ip->fields & SET)
+		op |= build_set(va_arg(ap, u32));
+	if (ip->fields & SCIMM)
+		op |= build_scimm(va_arg(ap, u32));
+	if (ip->fields & SIMM9)
+		op |= build_scimm9(va_arg(ap, u32));
+	va_end(ap);
+
+	**buf = op;
+	(*buf)++;
+}
+
+static inline void
+__resolve_relocs(struct uasm_reloc *rel, struct uasm_label *lab)
+{
+	long laddr = (long)lab->addr;
+	long raddr = (long)rel->addr;
+
+	switch (rel->type) {
+	case R_MIPS_PC16:
+		*rel->addr |= build_bimm(laddr - (raddr + 4));
+		break;
+
+	default:
+		panic("Unsupported Micro-assembler relocation %d",
+		      rel->type);
+	}
+}
diff --git a/arch/mips/mm/uasm.c b/arch/mips/mm/uasm.c
new file mode 100644
index 000000000..125140979
--- /dev/null
+++ b/arch/mips/mm/uasm.c
@@ -0,0 +1,644 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * A small micro-assembler. It is intentionally kept simple, does only
+ * support a subset of instructions, and does not try to hide pipeline
+ * effects like branch delay slots.
+ *
+ * Copyright (C) 2004, 2005, 2006, 2008	 Thiemo Seufer
+ * Copyright (C) 2005, 2007  Maciej W. Rozycki
+ * Copyright (C) 2006  Ralf Baechle (ralf@linux-mips.org)
+ * Copyright (C) 2012, 2013  MIPS Technologies, Inc.  All rights reserved.
+ */
+
+enum fields {
+	RS = 0x001,
+	RT = 0x002,
+	RD = 0x004,
+	RE = 0x008,
+	SIMM = 0x010,
+	UIMM = 0x020,
+	BIMM = 0x040,
+	JIMM = 0x080,
+	FUNC = 0x100,
+	SET = 0x200,
+	SCIMM = 0x400,
+	SIMM9 = 0x800,
+};
+
+#define OP_MASK		0x3f
+#define OP_SH		26
+#define RD_MASK		0x1f
+#define RD_SH		11
+#define RE_MASK		0x1f
+#define RE_SH		6
+#define IMM_MASK	0xffff
+#define IMM_SH		0
+#define JIMM_MASK	0x3ffffff
+#define JIMM_SH		0
+#define FUNC_MASK	0x3f
+#define FUNC_SH		0
+#define SET_MASK	0x7
+#define SET_SH		0
+#define SIMM9_SH	7
+#define SIMM9_MASK	0x1ff
+
+enum opcode {
+	insn_addiu, insn_addu, insn_and, insn_andi, insn_bbit0, insn_bbit1,
+	insn_beq, insn_beql, insn_bgez, insn_bgezl, insn_bgtz, insn_blez,
+	insn_bltz, insn_bltzl, insn_bne, insn_break, insn_cache, insn_cfc1,
+	insn_cfcmsa, insn_ctc1, insn_ctcmsa, insn_daddiu, insn_daddu, insn_ddivu,
+	insn_ddivu_r6, insn_di, insn_dins, insn_dinsm, insn_dinsu, insn_divu,
+	insn_divu_r6, insn_dmfc0, insn_dmodu, insn_dmtc0, insn_dmultu,
+	insn_dmulu, insn_drotr, insn_drotr32, insn_dsbh, insn_dshd, insn_dsll,
+	insn_dsll32, insn_dsllv, insn_dsra, insn_dsra32, insn_dsrav, insn_dsrl,
+	insn_dsrl32, insn_dsrlv, insn_dsubu, insn_eret, insn_ext, insn_ins,
+	insn_j, insn_jal, insn_jalr, insn_jr, insn_lb, insn_lbu, insn_ld,
+	insn_lddir, insn_ldpte, insn_ldx, insn_lh, insn_lhu, insn_ll, insn_lld,
+	insn_lui, insn_lw, insn_lwu, insn_lwx, insn_mfc0, insn_mfhc0, insn_mfhi,
+	insn_mflo, insn_modu, insn_movn, insn_movz, insn_mtc0, insn_mthc0,
+	insn_mthi, insn_mtlo, insn_mul, insn_multu, insn_mulu, insn_muhu, insn_nor,
+	insn_or, insn_ori, insn_pref, insn_rfe, insn_rotr, insn_sb, insn_sc,
+	insn_scd, insn_seleqz, insn_selnez, insn_sd, insn_sh, insn_sll,
+	insn_sllv, insn_slt, insn_slti, insn_sltiu, insn_sltu, insn_sra,
+	insn_srav, insn_srl, insn_srlv, insn_subu, insn_sw, insn_sync,
+	insn_syscall, insn_tlbp, insn_tlbr, insn_tlbwi, insn_tlbwr, insn_wait,
+	insn_wsbh, insn_xor, insn_xori, insn_yield,
+	insn_invalid /* insn_invalid must be last */
+};
+
+struct insn {
+	u32 match;
+	enum fields fields;
+};
+
+static inline u32 build_rs(u32 arg)
+{
+	WARN(arg & ~RS_MASK, KERN_WARNING "Micro-assembler field overflow\n");
+
+	return (arg & RS_MASK) << RS_SH;
+}
+
+static inline u32 build_rt(u32 arg)
+{
+	WARN(arg & ~RT_MASK, KERN_WARNING "Micro-assembler field overflow\n");
+
+	return (arg & RT_MASK) << RT_SH;
+}
+
+static inline u32 build_rd(u32 arg)
+{
+	WARN(arg & ~RD_MASK, KERN_WARNING "Micro-assembler field overflow\n");
+
+	return (arg & RD_MASK) << RD_SH;
+}
+
+static inline u32 build_re(u32 arg)
+{
+	WARN(arg & ~RE_MASK, KERN_WARNING "Micro-assembler field overflow\n");
+
+	return (arg & RE_MASK) << RE_SH;
+}
+
+static inline u32 build_simm(s32 arg)
+{
+	WARN(arg > 0x7fff || arg < -0x8000,
+	     KERN_WARNING "Micro-assembler field overflow\n");
+
+	return arg & 0xffff;
+}
+
+static inline u32 build_uimm(u32 arg)
+{
+	WARN(arg & ~IMM_MASK, KERN_WARNING "Micro-assembler field overflow\n");
+
+	return arg & IMM_MASK;
+}
+
+static inline u32 build_scimm(u32 arg)
+{
+	WARN(arg & ~SCIMM_MASK,
+	     KERN_WARNING "Micro-assembler field overflow\n");
+
+	return (arg & SCIMM_MASK) << SCIMM_SH;
+}
+
+static inline u32 build_scimm9(s32 arg)
+{
+	WARN((arg > 0xff || arg < -0x100),
+	       KERN_WARNING "Micro-assembler field overflow\n");
+
+	return (arg & SIMM9_MASK) << SIMM9_SH;
+}
+
+static inline u32 build_func(u32 arg)
+{
+	WARN(arg & ~FUNC_MASK, KERN_WARNING "Micro-assembler field overflow\n");
+
+	return arg & FUNC_MASK;
+}
+
+static inline u32 build_set(u32 arg)
+{
+	WARN(arg & ~SET_MASK, KERN_WARNING "Micro-assembler field overflow\n");
+
+	return arg & SET_MASK;
+}
+
+static void build_insn(u32 **buf, enum opcode opc, ...);
+
+#define I_u1u2u3(op)					\
+Ip_u1u2u3(op)						\
+{							\
+	build_insn(buf, insn##op, a, b, c);		\
+}							\
+UASM_EXPORT_SYMBOL(uasm_i##op);
+
+#define I_s3s1s2(op)					\
+Ip_s3s1s2(op)						\
+{							\
+	build_insn(buf, insn##op, b, c, a);		\
+}							\
+UASM_EXPORT_SYMBOL(uasm_i##op);
+
+#define I_u2u1u3(op)					\
+Ip_u2u1u3(op)						\
+{							\
+	build_insn(buf, insn##op, b, a, c);		\
+}							\
+UASM_EXPORT_SYMBOL(uasm_i##op);
+
+#define I_u3u2u1(op)					\
+Ip_u3u2u1(op)						\
+{							\
+	build_insn(buf, insn##op, c, b, a);		\
+}							\
+UASM_EXPORT_SYMBOL(uasm_i##op);
+
+#define I_u3u1u2(op)					\
+Ip_u3u1u2(op)						\
+{							\
+	build_insn(buf, insn##op, b, c, a);		\
+}							\
+UASM_EXPORT_SYMBOL(uasm_i##op);
+
+#define I_u1u2s3(op)					\
+Ip_u1u2s3(op)						\
+{							\
+	build_insn(buf, insn##op, a, b, c);		\
+}							\
+UASM_EXPORT_SYMBOL(uasm_i##op);
+
+#define I_u2s3u1(op)					\
+Ip_u2s3u1(op)						\
+{							\
+	build_insn(buf, insn##op, c, a, b);		\
+}							\
+UASM_EXPORT_SYMBOL(uasm_i##op);
+
+#define I_u2u1s3(op)					\
+Ip_u2u1s3(op)						\
+{							\
+	build_insn(buf, insn##op, b, a, c);		\
+}							\
+UASM_EXPORT_SYMBOL(uasm_i##op);
+
+#define I_u2u1msbu3(op)					\
+Ip_u2u1msbu3(op)					\
+{							\
+	build_insn(buf, insn##op, b, a, c+d-1, c);	\
+}							\
+UASM_EXPORT_SYMBOL(uasm_i##op);
+
+#define I_u2u1msb32u3(op)				\
+Ip_u2u1msbu3(op)					\
+{							\
+	build_insn(buf, insn##op, b, a, c+d-33, c);	\
+}							\
+UASM_EXPORT_SYMBOL(uasm_i##op);
+
+#define I_u2u1msb32msb3(op)				\
+Ip_u2u1msbu3(op)					\
+{							\
+	build_insn(buf, insn##op, b, a, c+d-33, c-32);	\
+}							\
+UASM_EXPORT_SYMBOL(uasm_i##op);
+
+#define I_u2u1msbdu3(op)				\
+Ip_u2u1msbu3(op)					\
+{							\
+	build_insn(buf, insn##op, b, a, d-1, c);	\
+}							\
+UASM_EXPORT_SYMBOL(uasm_i##op);
+
+#define I_u1u2(op)					\
+Ip_u1u2(op)						\
+{							\
+	build_insn(buf, insn##op, a, b);		\
+}							\
+UASM_EXPORT_SYMBOL(uasm_i##op);
+
+#define I_u2u1(op)					\
+Ip_u1u2(op)						\
+{							\
+	build_insn(buf, insn##op, b, a);		\
+}							\
+UASM_EXPORT_SYMBOL(uasm_i##op);
+
+#define I_u1s2(op)					\
+Ip_u1s2(op)						\
+{							\
+	build_insn(buf, insn##op, a, b);		\
+}							\
+UASM_EXPORT_SYMBOL(uasm_i##op);
+
+#define I_u1(op)					\
+Ip_u1(op)						\
+{							\
+	build_insn(buf, insn##op, a);			\
+}							\
+UASM_EXPORT_SYMBOL(uasm_i##op);
+
+#define I_0(op)						\
+Ip_0(op)						\
+{							\
+	build_insn(buf, insn##op);			\
+}							\
+UASM_EXPORT_SYMBOL(uasm_i##op);
+
+I_u2u1s3(_addiu)
+I_u3u1u2(_addu)
+I_u2u1u3(_andi)
+I_u3u1u2(_and)
+I_u1u2s3(_beq)
+I_u1u2s3(_beql)
+I_u1s2(_bgez)
+I_u1s2(_bgezl)
+I_u1s2(_bgtz)
+I_u1s2(_blez)
+I_u1s2(_bltz)
+I_u1s2(_bltzl)
+I_u1u2s3(_bne)
+I_u1(_break)
+I_u2s3u1(_cache)
+I_u1u2(_cfc1)
+I_u2u1(_cfcmsa)
+I_u1u2(_ctc1)
+I_u2u1(_ctcmsa)
+I_u1u2(_ddivu)
+I_u3u1u2(_ddivu_r6)
+I_u1u2u3(_dmfc0)
+I_u3u1u2(_dmodu)
+I_u1u2u3(_dmtc0)
+I_u1u2(_dmultu)
+I_u3u1u2(_dmulu)
+I_u2u1s3(_daddiu)
+I_u3u1u2(_daddu)
+I_u1(_di);
+I_u1u2(_divu)
+I_u3u1u2(_divu_r6)
+I_u2u1(_dsbh);
+I_u2u1(_dshd);
+I_u2u1u3(_dsll)
+I_u2u1u3(_dsll32)
+I_u3u2u1(_dsllv)
+I_u2u1u3(_dsra)
+I_u2u1u3(_dsra32)
+I_u3u2u1(_dsrav)
+I_u2u1u3(_dsrl)
+I_u2u1u3(_dsrl32)
+I_u3u2u1(_dsrlv)
+I_u2u1u3(_drotr)
+I_u2u1u3(_drotr32)
+I_u3u1u2(_dsubu)
+I_0(_eret)
+I_u2u1msbdu3(_ext)
+I_u2u1msbu3(_ins)
+I_u1(_j)
+I_u1(_jal)
+I_u2u1(_jalr)
+I_u1(_jr)
+I_u2s3u1(_lb)
+I_u2s3u1(_lbu)
+I_u2s3u1(_ld)
+I_u2s3u1(_lh)
+I_u2s3u1(_lhu)
+I_u2s3u1(_ll)
+I_u2s3u1(_lld)
+I_u1s2(_lui)
+I_u2s3u1(_lw)
+I_u2s3u1(_lwu)
+I_u1u2u3(_mfc0)
+I_u1u2u3(_mfhc0)
+I_u3u1u2(_modu)
+I_u3u1u2(_movn)
+I_u3u1u2(_movz)
+I_u1(_mfhi)
+I_u1(_mflo)
+I_u1u2u3(_mtc0)
+I_u1u2u3(_mthc0)
+I_u1(_mthi)
+I_u1(_mtlo)
+I_u3u1u2(_mul)
+I_u1u2(_multu)
+I_u3u1u2(_mulu)
+I_u3u1u2(_muhu)
+I_u3u1u2(_nor)
+I_u3u1u2(_or)
+I_u2u1u3(_ori)
+I_0(_rfe)
+I_u2s3u1(_sb)
+I_u2s3u1(_sc)
+I_u2s3u1(_scd)
+I_u2s3u1(_sd)
+I_u3u1u2(_seleqz)
+I_u3u1u2(_selnez)
+I_u2s3u1(_sh)
+I_u2u1u3(_sll)
+I_u3u2u1(_sllv)
+I_s3s1s2(_slt)
+I_u2u1s3(_slti)
+I_u2u1s3(_sltiu)
+I_u3u1u2(_sltu)
+I_u2u1u3(_sra)
+I_u3u2u1(_srav)
+I_u2u1u3(_srl)
+I_u3u2u1(_srlv)
+I_u2u1u3(_rotr)
+I_u3u1u2(_subu)
+I_u2s3u1(_sw)
+I_u1(_sync)
+I_0(_tlbp)
+I_0(_tlbr)
+I_0(_tlbwi)
+I_0(_tlbwr)
+I_u1(_wait);
+I_u2u1(_wsbh)
+I_u3u1u2(_xor)
+I_u2u1u3(_xori)
+I_u2u1(_yield)
+I_u2u1msbu3(_dins);
+I_u2u1msb32u3(_dinsm);
+I_u2u1msb32msb3(_dinsu);
+I_u1(_syscall);
+I_u1u2s3(_bbit0);
+I_u1u2s3(_bbit1);
+I_u3u1u2(_lwx)
+I_u3u1u2(_ldx)
+I_u1u2(_ldpte)
+I_u2u1u3(_lddir)
+
+#ifdef CONFIG_CPU_CAVIUM_OCTEON
+#include <asm/octeon/octeon.h>
+void uasm_i_pref(u32 **buf, unsigned int a, signed int b,
+			    unsigned int c)
+{
+	if (OCTEON_IS_MODEL(OCTEON_CN6XXX) && a <= 24 && a != 5)
+		/*
+		 * As per erratum Core-14449, replace prefetches 0-4,
+		 * 6-24 with 'pref 28'.
+		 */
+		build_insn(buf, insn_pref, c, 28, b);
+	else
+		build_insn(buf, insn_pref, c, a, b);
+}
+UASM_EXPORT_SYMBOL(uasm_i_pref);
+#else
+I_u2s3u1(_pref)
+#endif
+
+/* Handle labels. */
+void uasm_build_label(struct uasm_label **lab, u32 *addr, int lid)
+{
+	(*lab)->addr = addr;
+	(*lab)->lab = lid;
+	(*lab)++;
+}
+UASM_EXPORT_SYMBOL(uasm_build_label);
+
+int uasm_in_compat_space_p(long addr)
+{
+	/* Is this address in 32bit compat space? */
+	return addr == (int)addr;
+}
+UASM_EXPORT_SYMBOL(uasm_in_compat_space_p);
+
+static int uasm_rel_highest(long val)
+{
+#ifdef CONFIG_64BIT
+	return ((((val + 0x800080008000L) >> 48) & 0xffff) ^ 0x8000) - 0x8000;
+#else
+	return 0;
+#endif
+}
+
+static int uasm_rel_higher(long val)
+{
+#ifdef CONFIG_64BIT
+	return ((((val + 0x80008000L) >> 32) & 0xffff) ^ 0x8000) - 0x8000;
+#else
+	return 0;
+#endif
+}
+
+int uasm_rel_hi(long val)
+{
+	return ((((val + 0x8000L) >> 16) & 0xffff) ^ 0x8000) - 0x8000;
+}
+UASM_EXPORT_SYMBOL(uasm_rel_hi);
+
+int uasm_rel_lo(long val)
+{
+	return ((val & 0xffff) ^ 0x8000) - 0x8000;
+}
+UASM_EXPORT_SYMBOL(uasm_rel_lo);
+
+void UASM_i_LA_mostly(u32 **buf, unsigned int rs, long addr)
+{
+	if (!uasm_in_compat_space_p(addr)) {
+		uasm_i_lui(buf, rs, uasm_rel_highest(addr));
+		if (uasm_rel_higher(addr))
+			uasm_i_daddiu(buf, rs, rs, uasm_rel_higher(addr));
+		if (uasm_rel_hi(addr)) {
+			uasm_i_dsll(buf, rs, rs, 16);
+			uasm_i_daddiu(buf, rs, rs,
+					uasm_rel_hi(addr));
+			uasm_i_dsll(buf, rs, rs, 16);
+		} else
+			uasm_i_dsll32(buf, rs, rs, 0);
+	} else
+		uasm_i_lui(buf, rs, uasm_rel_hi(addr));
+}
+UASM_EXPORT_SYMBOL(UASM_i_LA_mostly);
+
+void UASM_i_LA(u32 **buf, unsigned int rs, long addr)
+{
+	UASM_i_LA_mostly(buf, rs, addr);
+	if (uasm_rel_lo(addr)) {
+		if (!uasm_in_compat_space_p(addr))
+			uasm_i_daddiu(buf, rs, rs,
+					uasm_rel_lo(addr));
+		else
+			uasm_i_addiu(buf, rs, rs,
+					uasm_rel_lo(addr));
+	}
+}
+UASM_EXPORT_SYMBOL(UASM_i_LA);
+
+/* Handle relocations. */
+void uasm_r_mips_pc16(struct uasm_reloc **rel, u32 *addr, int lid)
+{
+	(*rel)->addr = addr;
+	(*rel)->type = R_MIPS_PC16;
+	(*rel)->lab = lid;
+	(*rel)++;
+}
+UASM_EXPORT_SYMBOL(uasm_r_mips_pc16);
+
+static inline void __resolve_relocs(struct uasm_reloc *rel,
+				    struct uasm_label *lab);
+
+void uasm_resolve_relocs(struct uasm_reloc *rel,
+				  struct uasm_label *lab)
+{
+	struct uasm_label *l;
+
+	for (; rel->lab != UASM_LABEL_INVALID; rel++)
+		for (l = lab; l->lab != UASM_LABEL_INVALID; l++)
+			if (rel->lab == l->lab)
+				__resolve_relocs(rel, l);
+}
+UASM_EXPORT_SYMBOL(uasm_resolve_relocs);
+
+void uasm_move_relocs(struct uasm_reloc *rel, u32 *first, u32 *end,
+			       long off)
+{
+	for (; rel->lab != UASM_LABEL_INVALID; rel++)
+		if (rel->addr >= first && rel->addr < end)
+			rel->addr += off;
+}
+UASM_EXPORT_SYMBOL(uasm_move_relocs);
+
+void uasm_move_labels(struct uasm_label *lab, u32 *first, u32 *end,
+			       long off)
+{
+	for (; lab->lab != UASM_LABEL_INVALID; lab++)
+		if (lab->addr >= first && lab->addr < end)
+			lab->addr += off;
+}
+UASM_EXPORT_SYMBOL(uasm_move_labels);
+
+void uasm_copy_handler(struct uasm_reloc *rel, struct uasm_label *lab,
+				u32 *first, u32 *end, u32 *target)
+{
+	long off = (long)(target - first);
+
+	memcpy(target, first, (end - first) * sizeof(u32));
+
+	uasm_move_relocs(rel, first, end, off);
+	uasm_move_labels(lab, first, end, off);
+}
+UASM_EXPORT_SYMBOL(uasm_copy_handler);
+
+int uasm_insn_has_bdelay(struct uasm_reloc *rel, u32 *addr)
+{
+	for (; rel->lab != UASM_LABEL_INVALID; rel++) {
+		if (rel->addr == addr
+		    && (rel->type == R_MIPS_PC16
+			|| rel->type == R_MIPS_26))
+			return 1;
+	}
+
+	return 0;
+}
+UASM_EXPORT_SYMBOL(uasm_insn_has_bdelay);
+
+/* Convenience functions for labeled branches. */
+void uasm_il_bltz(u32 **p, struct uasm_reloc **r, unsigned int reg,
+			   int lid)
+{
+	uasm_r_mips_pc16(r, *p, lid);
+	uasm_i_bltz(p, reg, 0);
+}
+UASM_EXPORT_SYMBOL(uasm_il_bltz);
+
+void uasm_il_b(u32 **p, struct uasm_reloc **r, int lid)
+{
+	uasm_r_mips_pc16(r, *p, lid);
+	uasm_i_b(p, 0);
+}
+UASM_EXPORT_SYMBOL(uasm_il_b);
+
+void uasm_il_beq(u32 **p, struct uasm_reloc **r, unsigned int r1,
+			  unsigned int r2, int lid)
+{
+	uasm_r_mips_pc16(r, *p, lid);
+	uasm_i_beq(p, r1, r2, 0);
+}
+UASM_EXPORT_SYMBOL(uasm_il_beq);
+
+void uasm_il_beqz(u32 **p, struct uasm_reloc **r, unsigned int reg,
+			   int lid)
+{
+	uasm_r_mips_pc16(r, *p, lid);
+	uasm_i_beqz(p, reg, 0);
+}
+UASM_EXPORT_SYMBOL(uasm_il_beqz);
+
+void uasm_il_beqzl(u32 **p, struct uasm_reloc **r, unsigned int reg,
+			    int lid)
+{
+	uasm_r_mips_pc16(r, *p, lid);
+	uasm_i_beqzl(p, reg, 0);
+}
+UASM_EXPORT_SYMBOL(uasm_il_beqzl);
+
+void uasm_il_bne(u32 **p, struct uasm_reloc **r, unsigned int reg1,
+			  unsigned int reg2, int lid)
+{
+	uasm_r_mips_pc16(r, *p, lid);
+	uasm_i_bne(p, reg1, reg2, 0);
+}
+UASM_EXPORT_SYMBOL(uasm_il_bne);
+
+void uasm_il_bnez(u32 **p, struct uasm_reloc **r, unsigned int reg,
+			   int lid)
+{
+	uasm_r_mips_pc16(r, *p, lid);
+	uasm_i_bnez(p, reg, 0);
+}
+UASM_EXPORT_SYMBOL(uasm_il_bnez);
+
+void uasm_il_bgezl(u32 **p, struct uasm_reloc **r, unsigned int reg,
+			    int lid)
+{
+	uasm_r_mips_pc16(r, *p, lid);
+	uasm_i_bgezl(p, reg, 0);
+}
+UASM_EXPORT_SYMBOL(uasm_il_bgezl);
+
+void uasm_il_bgez(u32 **p, struct uasm_reloc **r, unsigned int reg,
+			   int lid)
+{
+	uasm_r_mips_pc16(r, *p, lid);
+	uasm_i_bgez(p, reg, 0);
+}
+UASM_EXPORT_SYMBOL(uasm_il_bgez);
+
+void uasm_il_bbit0(u32 **p, struct uasm_reloc **r, unsigned int reg,
+			    unsigned int bit, int lid)
+{
+	uasm_r_mips_pc16(r, *p, lid);
+	uasm_i_bbit0(p, reg, bit, 0);
+}
+UASM_EXPORT_SYMBOL(uasm_il_bbit0);
+
+void uasm_il_bbit1(u32 **p, struct uasm_reloc **r, unsigned int reg,
+			    unsigned int bit, int lid)
+{
+	uasm_r_mips_pc16(r, *p, lid);
+	uasm_i_bbit1(p, reg, bit, 0);
+}
+UASM_EXPORT_SYMBOL(uasm_il_bbit1);
diff --git a/arch/mips/mti-malta/Makefile b/arch/mips/mti-malta/Makefile
new file mode 100644
index 000000000..13bbd12bf
--- /dev/null
+++ b/arch/mips/mti-malta/Makefile
@@ -0,0 +1,19 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Carsten Langgaard, carstenl@mips.com
+# Copyright (C) 1999,2000 MIPS Technologies, Inc.  All rights reserved.
+#
+# Copyright (C) 2008 Wind River Systems, Inc.
+#   written by Ralf Baechle <ralf@linux-mips.org>
+#
+obj-y				+= malta-dtshim.o
+obj-y				+= malta-init.o
+obj-y				+= malta-int.o
+obj-y				+= malta-memory.o
+obj-y				+= malta-platform.o
+obj-y				+= malta-setup.o
+obj-y				+= malta-time.o
+
+obj-$(CONFIG_MIPS_CMP)		+= malta-amon.o
+
+CFLAGS_malta-dtshim.o = -I$(src)/../../../scripts/dtc/libfdt
diff --git a/arch/mips/mti-malta/Platform b/arch/mips/mti-malta/Platform
new file mode 100644
index 000000000..f4616934d
--- /dev/null
+++ b/arch/mips/mti-malta/Platform
@@ -0,0 +1,6 @@
+#
+# MIPS Malta board
+#
+cflags-$(CONFIG_MIPS_MALTA)	+= -I$(srctree)/arch/mips/include/asm/mach-malta
+load-$(CONFIG_MIPS_MALTA)	+= 0xffffffff80100000
+all-$(CONFIG_MIPS_MALTA)	:= $(COMPRESSION_FNAME).bin
diff --git a/arch/mips/mti-malta/malta-amon.c b/arch/mips/mti-malta/malta-amon.c
new file mode 100644
index 000000000..84ac523b0
--- /dev/null
+++ b/arch/mips/mti-malta/malta-amon.c
@@ -0,0 +1,88 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2007 MIPS Technologies, Inc.  All rights reserved.
+ * Copyright (C) 2013 Imagination Technologies Ltd.
+ *
+ * Arbitrary Monitor Interface
+ */
+#include <linux/kernel.h>
+#include <linux/smp.h>
+
+#include <asm/addrspace.h>
+#include <asm/mipsmtregs.h>
+#include <asm/mips-boards/launch.h>
+#include <asm/vpe.h>
+
+int amon_cpu_avail(int cpu)
+{
+	struct cpulaunch *launch = (struct cpulaunch *)CKSEG0ADDR(CPULAUNCH);
+
+	if (cpu < 0 || cpu >= NCPULAUNCH) {
+		pr_debug("avail: cpu%d is out of range\n", cpu);
+		return 0;
+	}
+
+	launch += cpu;
+	if (!(launch->flags & LAUNCH_FREADY)) {
+		pr_debug("avail: cpu%d is not ready\n", cpu);
+		return 0;
+	}
+	if (launch->flags & (LAUNCH_FGO|LAUNCH_FGONE)) {
+		pr_debug("avail: too late.. cpu%d is already gone\n", cpu);
+		return 0;
+	}
+
+	return 1;
+}
+
+int amon_cpu_start(int cpu,
+		    unsigned long pc, unsigned long sp,
+		    unsigned long gp, unsigned long a0)
+{
+	volatile struct cpulaunch *launch =
+		(struct cpulaunch  *)CKSEG0ADDR(CPULAUNCH);
+
+	if (!amon_cpu_avail(cpu))
+		return -1;
+	if (cpu == smp_processor_id()) {
+		pr_debug("launch: I am cpu%d!\n", cpu);
+		return -1;
+	}
+	launch += cpu;
+
+	pr_debug("launch: starting cpu%d\n", cpu);
+
+	launch->pc = pc;
+	launch->gp = gp;
+	launch->sp = sp;
+	launch->a0 = a0;
+
+	smp_wmb();		/* Target must see parameters before go */
+	launch->flags |= LAUNCH_FGO;
+	smp_wmb();		/* Target must see go before we poll  */
+
+	while ((launch->flags & LAUNCH_FGONE) == 0)
+		;
+	smp_rmb();	/* Target will be updating flags soon */
+	pr_debug("launch: cpu%d gone!\n", cpu);
+
+	return 0;
+}
+
+#ifdef CONFIG_MIPS_VPE_LOADER_CMP
+int vpe_run(struct vpe *v)
+{
+	struct vpe_notifications *n;
+
+	if (amon_cpu_start(aprp_cpu_index(), v->__start, 0, 0, 0) < 0)
+		return -1;
+
+	list_for_each_entry(n, &v->notify, list)
+		n->start(VPE_MODULE_MINOR);
+
+	return 0;
+}
+#endif
diff --git a/arch/mips/mti-malta/malta-dtshim.c b/arch/mips/mti-malta/malta-dtshim.c
new file mode 100644
index 000000000..f451268f6
--- /dev/null
+++ b/arch/mips/mti-malta/malta-dtshim.c
@@ -0,0 +1,333 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2015 Imagination Technologies
+ * Author: Paul Burton <paul.burton@mips.com>
+ */
+
+#include <linux/bug.h>
+#include <linux/kernel.h>
+#include <linux/libfdt.h>
+#include <linux/of_fdt.h>
+#include <linux/sizes.h>
+#include <asm/addrspace.h>
+#include <asm/bootinfo.h>
+#include <asm/fw/fw.h>
+#include <asm/mips-boards/generic.h>
+#include <asm/mips-boards/malta.h>
+#include <asm/mips-cps.h>
+#include <asm/page.h>
+
+#define ROCIT_REG_BASE			0x1f403000
+#define ROCIT_CONFIG_GEN1		(ROCIT_REG_BASE + 0x04)
+#define  ROCIT_CONFIG_GEN1_MEMMAP_SHIFT	8
+#define  ROCIT_CONFIG_GEN1_MEMMAP_MASK	(0xf << 8)
+
+static unsigned char fdt_buf[16 << 10] __initdata __aligned(8);
+
+/* determined physical memory size, not overridden by command line args	 */
+extern unsigned long physical_memsize;
+
+enum mem_map {
+	MEM_MAP_V1 = 0,
+	MEM_MAP_V2,
+};
+
+#define MAX_MEM_ARRAY_ENTRIES 2
+
+static __init int malta_scon(void)
+{
+	int scon = MIPS_REVISION_SCONID;
+
+	if (scon != MIPS_REVISION_SCON_OTHER)
+		return scon;
+
+	switch (MIPS_REVISION_CORID) {
+	case MIPS_REVISION_CORID_QED_RM5261:
+	case MIPS_REVISION_CORID_CORE_LV:
+	case MIPS_REVISION_CORID_CORE_FPGA:
+	case MIPS_REVISION_CORID_CORE_FPGAR2:
+		return MIPS_REVISION_SCON_GT64120;
+
+	case MIPS_REVISION_CORID_CORE_EMUL_BON:
+	case MIPS_REVISION_CORID_BONITO64:
+	case MIPS_REVISION_CORID_CORE_20K:
+		return MIPS_REVISION_SCON_BONITO;
+
+	case MIPS_REVISION_CORID_CORE_MSC:
+	case MIPS_REVISION_CORID_CORE_FPGA2:
+	case MIPS_REVISION_CORID_CORE_24K:
+		return MIPS_REVISION_SCON_SOCIT;
+
+	case MIPS_REVISION_CORID_CORE_FPGA3:
+	case MIPS_REVISION_CORID_CORE_FPGA4:
+	case MIPS_REVISION_CORID_CORE_FPGA5:
+	case MIPS_REVISION_CORID_CORE_EMUL_MSC:
+	default:
+		return MIPS_REVISION_SCON_ROCIT;
+	}
+}
+
+static unsigned __init gen_fdt_mem_array(__be32 *mem_array, unsigned long size,
+					 enum mem_map map)
+{
+	unsigned long size_preio;
+	unsigned entries;
+
+	entries = 1;
+	mem_array[0] = cpu_to_be32(PHYS_OFFSET);
+	if (IS_ENABLED(CONFIG_EVA)) {
+		/*
+		 * The current Malta EVA configuration is "special" in that it
+		 * always makes use of addresses in the upper half of the 32 bit
+		 * physical address map, which gives it a contiguous region of
+		 * DDR but limits it to 2GB.
+		 */
+		mem_array[1] = cpu_to_be32(size);
+		goto done;
+	}
+
+	size_preio = min_t(unsigned long, size, SZ_256M);
+	mem_array[1] = cpu_to_be32(size_preio);
+	size -= size_preio;
+	if (!size)
+		goto done;
+
+	if (map == MEM_MAP_V2) {
+		/*
+		 * We have a flat 32 bit physical memory map with DDR filling
+		 * all 4GB of the memory map, apart from the I/O region which
+		 * obscures 256MB from 0x10000000-0x1fffffff.
+		 *
+		 * Therefore we discard the 256MB behind the I/O region.
+		 */
+		if (size <= SZ_256M)
+			goto done;
+		size -= SZ_256M;
+
+		/* Make use of the memory following the I/O region */
+		entries++;
+		mem_array[2] = cpu_to_be32(PHYS_OFFSET + SZ_512M);
+		mem_array[3] = cpu_to_be32(size);
+	} else {
+		/*
+		 * We have a 32 bit physical memory map with a 2GB DDR region
+		 * aliased in the upper & lower halves of it. The I/O region
+		 * obscures 256MB from 0x10000000-0x1fffffff in the low alias
+		 * but the DDR it obscures is accessible via the high alias.
+		 *
+		 * Simply access everything beyond the lowest 256MB of DDR using
+		 * the high alias.
+		 */
+		entries++;
+		mem_array[2] = cpu_to_be32(PHYS_OFFSET + SZ_2G + SZ_256M);
+		mem_array[3] = cpu_to_be32(size);
+	}
+
+done:
+	BUG_ON(entries > MAX_MEM_ARRAY_ENTRIES);
+	return entries;
+}
+
+static void __init append_memory(void *fdt, int root_off)
+{
+	__be32 mem_array[2 * MAX_MEM_ARRAY_ENTRIES];
+	unsigned long memsize;
+	unsigned mem_entries;
+	int i, err, mem_off;
+	enum mem_map mem_map;
+	u32 config;
+	char *var, param_name[10], *var_names[] = {
+		"ememsize", "memsize",
+	};
+
+	/* if a memory node already exists, leave it alone */
+	mem_off = fdt_path_offset(fdt, "/memory");
+	if (mem_off >= 0)
+		return;
+
+	/* find memory size from the bootloader environment */
+	for (i = 0; i < ARRAY_SIZE(var_names); i++) {
+		var = fw_getenv(var_names[i]);
+		if (!var)
+			continue;
+
+		err = kstrtoul(var, 0, &physical_memsize);
+		if (!err)
+			break;
+
+		pr_warn("Failed to read the '%s' env variable '%s'\n",
+			var_names[i], var);
+	}
+
+	if (!physical_memsize) {
+		pr_warn("The bootloader didn't provide memsize: defaulting to 32MB\n");
+		physical_memsize = 32 << 20;
+	}
+
+	if (IS_ENABLED(CONFIG_CPU_BIG_ENDIAN)) {
+		/*
+		 * SOC-it swaps, or perhaps doesn't swap, when DMA'ing
+		 * the last word of physical memory.
+		 */
+		physical_memsize -= PAGE_SIZE;
+	}
+
+	/* default to using all available RAM */
+	memsize = physical_memsize;
+
+	/* allow the user to override the usable memory */
+	for (i = 0; i < ARRAY_SIZE(var_names); i++) {
+		snprintf(param_name, sizeof(param_name), "%s=", var_names[i]);
+		var = strstr(arcs_cmdline, param_name);
+		if (!var)
+			continue;
+
+		memsize = memparse(var + strlen(param_name), NULL);
+	}
+
+	/* if the user says there's more RAM than we thought, believe them */
+	physical_memsize = max_t(unsigned long, physical_memsize, memsize);
+
+	/* detect the memory map in use */
+	if (malta_scon() == MIPS_REVISION_SCON_ROCIT) {
+		/* ROCit has a register indicating the memory map in use */
+		config = readl((void __iomem *)CKSEG1ADDR(ROCIT_CONFIG_GEN1));
+		mem_map = config & ROCIT_CONFIG_GEN1_MEMMAP_MASK;
+		mem_map >>= ROCIT_CONFIG_GEN1_MEMMAP_SHIFT;
+	} else {
+		/* if not using ROCit, presume the v1 memory map */
+		mem_map = MEM_MAP_V1;
+	}
+	if (mem_map > MEM_MAP_V2)
+		panic("Unsupported physical memory map v%u detected",
+		      (unsigned int)mem_map);
+
+	/* append memory to the DT */
+	mem_off = fdt_add_subnode(fdt, root_off, "memory");
+	if (mem_off < 0)
+		panic("Unable to add memory node to DT: %d", mem_off);
+
+	err = fdt_setprop_string(fdt, mem_off, "device_type", "memory");
+	if (err)
+		panic("Unable to set memory node device_type: %d", err);
+
+	mem_entries = gen_fdt_mem_array(mem_array, physical_memsize, mem_map);
+	err = fdt_setprop(fdt, mem_off, "reg", mem_array,
+			  mem_entries * 2 * sizeof(mem_array[0]));
+	if (err)
+		panic("Unable to set memory regs property: %d", err);
+
+	mem_entries = gen_fdt_mem_array(mem_array, memsize, mem_map);
+	err = fdt_setprop(fdt, mem_off, "linux,usable-memory", mem_array,
+			  mem_entries * 2 * sizeof(mem_array[0]));
+	if (err)
+		panic("Unable to set linux,usable-memory property: %d", err);
+}
+
+static void __init remove_gic(void *fdt)
+{
+	int err, gic_off, i8259_off, cpu_off;
+	void __iomem *biu_base;
+	uint32_t cpu_phandle, sc_cfg;
+
+	/* if we have a CM which reports a GIC is present, leave the DT alone */
+	err = mips_cm_probe();
+	if (!err && (read_gcr_gic_status() & CM_GCR_GIC_STATUS_EX))
+		return;
+
+	if (malta_scon() == MIPS_REVISION_SCON_ROCIT) {
+		/*
+		 * On systems using the RocIT system controller a GIC may be
+		 * present without a CM. Detect whether that is the case.
+		 */
+		biu_base = ioremap(MSC01_BIU_REG_BASE,
+				MSC01_BIU_ADDRSPACE_SZ);
+		sc_cfg = __raw_readl(biu_base + MSC01_SC_CFG_OFS);
+		if (sc_cfg & MSC01_SC_CFG_GICPRES_MSK) {
+			/* enable the GIC at the system controller level */
+			sc_cfg |= BIT(MSC01_SC_CFG_GICENA_SHF);
+			__raw_writel(sc_cfg, biu_base + MSC01_SC_CFG_OFS);
+			return;
+		}
+	}
+
+	gic_off = fdt_node_offset_by_compatible(fdt, -1, "mti,gic");
+	if (gic_off < 0) {
+		pr_warn("malta-dtshim: unable to find DT GIC node: %d\n",
+			gic_off);
+		return;
+	}
+
+	err = fdt_nop_node(fdt, gic_off);
+	if (err)
+		pr_warn("malta-dtshim: unable to nop GIC node\n");
+
+	i8259_off = fdt_node_offset_by_compatible(fdt, -1, "intel,i8259");
+	if (i8259_off < 0) {
+		pr_warn("malta-dtshim: unable to find DT i8259 node: %d\n",
+			i8259_off);
+		return;
+	}
+
+	cpu_off = fdt_node_offset_by_compatible(fdt, -1,
+			"mti,cpu-interrupt-controller");
+	if (cpu_off < 0) {
+		pr_warn("malta-dtshim: unable to find CPU intc node: %d\n",
+			cpu_off);
+		return;
+	}
+
+	cpu_phandle = fdt_get_phandle(fdt, cpu_off);
+	if (!cpu_phandle) {
+		pr_warn("malta-dtshim: unable to get CPU intc phandle\n");
+		return;
+	}
+
+	err = fdt_setprop_u32(fdt, i8259_off, "interrupt-parent", cpu_phandle);
+	if (err) {
+		pr_warn("malta-dtshim: unable to set i8259 interrupt-parent: %d\n",
+			err);
+		return;
+	}
+
+	err = fdt_setprop_u32(fdt, i8259_off, "interrupts", 2);
+	if (err) {
+		pr_warn("malta-dtshim: unable to set i8259 interrupts: %d\n",
+			err);
+		return;
+	}
+}
+
+void __init *malta_dt_shim(void *fdt)
+{
+	int root_off, len, err;
+	const char *compat;
+
+	if (fdt_check_header(fdt))
+		panic("Corrupt DT");
+
+	err = fdt_open_into(fdt, fdt_buf, sizeof(fdt_buf));
+	if (err)
+		panic("Unable to open FDT: %d", err);
+
+	root_off = fdt_path_offset(fdt_buf, "/");
+	if (root_off < 0)
+		panic("No / node in DT");
+
+	compat = fdt_getprop(fdt_buf, root_off, "compatible", &len);
+	if (!compat)
+		panic("No root compatible property in DT: %d", len);
+
+	/* if this isn't Malta, leave the DT alone */
+	if (strncmp(compat, "mti,malta", len))
+		return fdt;
+
+	append_memory(fdt_buf, root_off);
+	remove_gic(fdt_buf);
+
+	err = fdt_pack(fdt_buf);
+	if (err)
+		panic("Unable to pack FDT: %d\n", err);
+
+	return fdt_buf;
+}
diff --git a/arch/mips/mti-malta/malta-init.c b/arch/mips/mti-malta/malta-init.c
new file mode 100644
index 000000000..b03cac5fd
--- /dev/null
+++ b/arch/mips/mti-malta/malta-init.c
@@ -0,0 +1,297 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * PROM library initialisation code.
+ *
+ * Copyright (C) 1999,2000,2004,2005,2012  MIPS Technologies, Inc.
+ * All rights reserved.
+ * Authors: Carsten Langgaard <carstenl@mips.com>
+ *         Maciej W. Rozycki <macro@mips.com>
+ *          Steven J. Hill <sjhill@mips.com>
+ */
+#include <linux/init.h>
+#include <linux/string.h>
+#include <linux/kernel.h>
+#include <linux/pci_regs.h>
+#include <linux/serial_core.h>
+
+#include <asm/cacheflush.h>
+#include <asm/smp-ops.h>
+#include <asm/traps.h>
+#include <asm/fw/fw.h>
+#include <asm/mips-cps.h>
+#include <asm/mips-boards/generic.h>
+#include <asm/mips-boards/malta.h>
+
+static int mips_revision_corid;
+int mips_revision_sconid;
+
+/* Bonito64 system controller register base. */
+unsigned long _pcictrl_bonito;
+unsigned long _pcictrl_bonito_pcicfg;
+
+/* GT64120 system controller register base */
+unsigned long _pcictrl_gt64120;
+
+/* MIPS System controller register base */
+unsigned long _pcictrl_msc;
+
+#ifdef CONFIG_SERIAL_8250_CONSOLE
+static void __init console_config(void)
+{
+	char console_string[40];
+	int baud = 0;
+	char parity = '\0', bits = '\0', flow = '\0';
+	char *s;
+
+	s = fw_getenv("modetty0");
+	if (s) {
+		while (*s >= '0' && *s <= '9')
+			baud = baud*10 + *s++ - '0';
+		if (*s == ',')
+			s++;
+		if (*s)
+			parity = *s++;
+		if (*s == ',')
+			s++;
+		if (*s)
+			bits = *s++;
+		if (*s == ',')
+			s++;
+		if (*s == 'h')
+			flow = 'r';
+	}
+	if (baud == 0)
+		baud = 38400;
+	if (parity != 'n' && parity != 'o' && parity != 'e')
+		parity = 'n';
+	if (bits != '7' && bits != '8')
+		bits = '8';
+	if (flow == '\0')
+		flow = 'r';
+
+	if ((strstr(fw_getcmdline(), "earlycon=")) == NULL) {
+		sprintf(console_string, "uart8250,io,0x3f8,%d%c%c", baud,
+			parity, bits);
+		setup_earlycon(console_string);
+	}
+
+	if ((strstr(fw_getcmdline(), "console=")) == NULL) {
+		sprintf(console_string, " console=ttyS0,%d%c%c%c", baud,
+			parity, bits, flow);
+		strcat(fw_getcmdline(), console_string);
+		pr_info("Config serial console:%s\n", console_string);
+	}
+}
+#endif
+
+static void __init mips_nmi_setup(void)
+{
+	void *base;
+
+	base = cpu_has_veic ?
+		(void *)(CAC_BASE + 0xa80) :
+		(void *)(CAC_BASE + 0x380);
+	memcpy(base, except_vec_nmi, 0x80);
+	flush_icache_range((unsigned long)base, (unsigned long)base + 0x80);
+}
+
+static void __init mips_ejtag_setup(void)
+{
+	void *base;
+	extern char except_vec_ejtag_debug[];
+
+	base = cpu_has_veic ?
+		(void *)(CAC_BASE + 0xa00) :
+		(void *)(CAC_BASE + 0x300);
+	memcpy(base, except_vec_ejtag_debug, 0x80);
+	flush_icache_range((unsigned long)base, (unsigned long)base + 0x80);
+}
+
+phys_addr_t mips_cpc_default_phys_base(void)
+{
+	return CPC_BASE_ADDR;
+}
+
+void __init prom_init(void)
+{
+	/*
+	 * early setup of _pcictrl_bonito so that we can determine
+	 * the system controller on a CORE_EMUL board
+	 */
+	_pcictrl_bonito = (unsigned long)ioremap(BONITO_REG_BASE, BONITO_REG_SIZE);
+
+	mips_revision_corid = MIPS_REVISION_CORID;
+
+	if (mips_revision_corid == MIPS_REVISION_CORID_CORE_EMUL) {
+		if (BONITO_PCIDID == 0x0001df53 ||
+		    BONITO_PCIDID == 0x0003df53)
+			mips_revision_corid = MIPS_REVISION_CORID_CORE_EMUL_BON;
+		else
+			mips_revision_corid = MIPS_REVISION_CORID_CORE_EMUL_MSC;
+	}
+
+	mips_revision_sconid = MIPS_REVISION_SCONID;
+	if (mips_revision_sconid == MIPS_REVISION_SCON_OTHER) {
+		switch (mips_revision_corid) {
+		case MIPS_REVISION_CORID_QED_RM5261:
+		case MIPS_REVISION_CORID_CORE_LV:
+		case MIPS_REVISION_CORID_CORE_FPGA:
+		case MIPS_REVISION_CORID_CORE_FPGAR2:
+			mips_revision_sconid = MIPS_REVISION_SCON_GT64120;
+			break;
+		case MIPS_REVISION_CORID_CORE_EMUL_BON:
+		case MIPS_REVISION_CORID_BONITO64:
+		case MIPS_REVISION_CORID_CORE_20K:
+			mips_revision_sconid = MIPS_REVISION_SCON_BONITO;
+			break;
+		case MIPS_REVISION_CORID_CORE_MSC:
+		case MIPS_REVISION_CORID_CORE_FPGA2:
+		case MIPS_REVISION_CORID_CORE_24K:
+			/*
+			 * SOCit/ROCit support is essentially identical
+			 * but make an attempt to distinguish them
+			 */
+			mips_revision_sconid = MIPS_REVISION_SCON_SOCIT;
+			break;
+		case MIPS_REVISION_CORID_CORE_FPGA3:
+		case MIPS_REVISION_CORID_CORE_FPGA4:
+		case MIPS_REVISION_CORID_CORE_FPGA5:
+		case MIPS_REVISION_CORID_CORE_EMUL_MSC:
+		default:
+			/* See above */
+			mips_revision_sconid = MIPS_REVISION_SCON_ROCIT;
+			break;
+		}
+	}
+
+	switch (mips_revision_sconid) {
+		u32 start, map, mask, data;
+
+	case MIPS_REVISION_SCON_GT64120:
+		/*
+		 * Setup the North bridge to do Master byte-lane swapping
+		 * when running in bigendian.
+		 */
+		_pcictrl_gt64120 = (unsigned long)ioremap(MIPS_GT_BASE, 0x2000);
+
+#ifdef CONFIG_CPU_LITTLE_ENDIAN
+		GT_WRITE(GT_PCI0_CMD_OFS, GT_PCI0_CMD_MBYTESWAP_BIT |
+			 GT_PCI0_CMD_SBYTESWAP_BIT);
+#else
+		GT_WRITE(GT_PCI0_CMD_OFS, 0);
+#endif
+		/* Fix up PCI I/O mapping if necessary (for Atlas).  */
+		start = GT_READ(GT_PCI0IOLD_OFS);
+		map = GT_READ(GT_PCI0IOREMAP_OFS);
+		if ((start & map) != 0) {
+			map &= ~start;
+			GT_WRITE(GT_PCI0IOREMAP_OFS, map);
+		}
+
+		set_io_port_base(MALTA_GT_PORT_BASE);
+		break;
+
+	case MIPS_REVISION_SCON_BONITO:
+		_pcictrl_bonito_pcicfg = (unsigned long)ioremap(BONITO_PCICFG_BASE, BONITO_PCICFG_SIZE);
+
+		/*
+		 * Disable Bonito IOBC.
+		 */
+		BONITO_PCIMEMBASECFG = BONITO_PCIMEMBASECFG &
+			~(BONITO_PCIMEMBASECFG_MEMBASE0_CACHED |
+			  BONITO_PCIMEMBASECFG_MEMBASE1_CACHED);
+
+		/*
+		 * Setup the North bridge to do Master byte-lane swapping
+		 * when running in bigendian.
+		 */
+#ifdef CONFIG_CPU_LITTLE_ENDIAN
+		BONITO_BONGENCFG = BONITO_BONGENCFG &
+			~(BONITO_BONGENCFG_MSTRBYTESWAP |
+			  BONITO_BONGENCFG_BYTESWAP);
+#else
+		BONITO_BONGENCFG = BONITO_BONGENCFG |
+			BONITO_BONGENCFG_MSTRBYTESWAP |
+			BONITO_BONGENCFG_BYTESWAP;
+#endif
+
+		set_io_port_base(MALTA_BONITO_PORT_BASE);
+		break;
+
+	case MIPS_REVISION_SCON_SOCIT:
+	case MIPS_REVISION_SCON_ROCIT:
+		_pcictrl_msc = (unsigned long)ioremap(MIPS_MSC01_PCI_REG_BASE, 0x2000);
+mips_pci_controller:
+		mb();
+		MSC_READ(MSC01_PCI_CFG, data);
+		MSC_WRITE(MSC01_PCI_CFG, data & ~MSC01_PCI_CFG_EN_BIT);
+		wmb();
+
+		/* Fix up lane swapping.  */
+#ifdef CONFIG_CPU_LITTLE_ENDIAN
+		MSC_WRITE(MSC01_PCI_SWAP, MSC01_PCI_SWAP_NOSWAP);
+#else
+		MSC_WRITE(MSC01_PCI_SWAP,
+			  MSC01_PCI_SWAP_BYTESWAP << MSC01_PCI_SWAP_IO_SHF |
+			  MSC01_PCI_SWAP_BYTESWAP << MSC01_PCI_SWAP_MEM_SHF |
+			  MSC01_PCI_SWAP_BYTESWAP << MSC01_PCI_SWAP_BAR0_SHF);
+#endif
+
+		/*
+		 * Setup the Malta max (2GB) memory for PCI DMA in host bridge
+		 * in transparent addressing mode.
+		 */
+		mask = PHYS_OFFSET | PCI_BASE_ADDRESS_MEM_PREFETCH;
+		MSC_WRITE(MSC01_PCI_BAR0, mask);
+		MSC_WRITE(MSC01_PCI_HEAD4, mask);
+
+		mask &= MSC01_PCI_BAR0_SIZE_MSK;
+		MSC_WRITE(MSC01_PCI_P2SCMSKL, mask);
+		MSC_WRITE(MSC01_PCI_P2SCMAPL, mask);
+
+		/* Don't handle target retries indefinitely.  */
+		if ((data & MSC01_PCI_CFG_MAXRTRY_MSK) ==
+		    MSC01_PCI_CFG_MAXRTRY_MSK)
+			data = (data & ~(MSC01_PCI_CFG_MAXRTRY_MSK <<
+					 MSC01_PCI_CFG_MAXRTRY_SHF)) |
+			       ((MSC01_PCI_CFG_MAXRTRY_MSK - 1) <<
+				MSC01_PCI_CFG_MAXRTRY_SHF);
+
+		wmb();
+		MSC_WRITE(MSC01_PCI_CFG, data);
+		mb();
+
+		set_io_port_base(MALTA_MSC_PORT_BASE);
+		break;
+
+	case MIPS_REVISION_SCON_SOCITSC:
+	case MIPS_REVISION_SCON_SOCITSCP:
+		_pcictrl_msc = (unsigned long)ioremap(MIPS_SOCITSC_PCI_REG_BASE, 0x2000);
+		goto mips_pci_controller;
+
+	default:
+		/* Unknown system controller */
+		while (1);	/* We die here... */
+	}
+	board_nmi_handler_setup = mips_nmi_setup;
+	board_ejtag_handler_setup = mips_ejtag_setup;
+
+	fw_init_cmdline();
+	fw_meminit();
+#ifdef CONFIG_SERIAL_8250_CONSOLE
+	console_config();
+#endif
+	/* Early detection of CMP support */
+	mips_cpc_probe();
+
+	if (!register_cps_smp_ops())
+		return;
+	if (!register_cmp_smp_ops())
+		return;
+	if (!register_vsmp_smp_ops())
+		return;
+	register_up_smp_ops();
+}
diff --git a/arch/mips/mti-malta/malta-int.c b/arch/mips/mti-malta/malta-int.c
new file mode 100644
index 000000000..03d85b2b3
--- /dev/null
+++ b/arch/mips/mti-malta/malta-int.c
@@ -0,0 +1,223 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 2000, 2001, 2004 MIPS Technologies, Inc.
+ * Copyright (C) 2001 Ralf Baechle
+ * Copyright (C) 2013 Imagination Technologies Ltd.
+ *
+ * Routines for generic manipulation of the interrupts found on the MIPS
+ * Malta board. The interrupt controller is located in the South Bridge
+ * a PIIX4 device with two internal 82C95 interrupt controllers.
+ */
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <linux/irqchip.h>
+#include <linux/sched.h>
+#include <linux/smp.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/of_irq.h>
+#include <linux/kernel_stat.h>
+#include <linux/kernel.h>
+#include <linux/random.h>
+
+#include <asm/traps.h>
+#include <asm/i8259.h>
+#include <asm/irq_cpu.h>
+#include <asm/irq_regs.h>
+#include <asm/mips-boards/malta.h>
+#include <asm/mips-boards/maltaint.h>
+#include <asm/mips-cps.h>
+#include <asm/gt64120.h>
+#include <asm/mips-boards/generic.h>
+#include <asm/mips-boards/msc01_pci.h>
+#include <asm/msc01_ic.h>
+#include <asm/setup.h>
+#include <asm/rtlx.h>
+
+static inline int mips_pcibios_iack(void)
+{
+	int irq;
+
+	/*
+	 * Determine highest priority pending interrupt by performing
+	 * a PCI Interrupt Acknowledge cycle.
+	 */
+	switch (mips_revision_sconid) {
+	case MIPS_REVISION_SCON_SOCIT:
+	case MIPS_REVISION_SCON_ROCIT:
+	case MIPS_REVISION_SCON_SOCITSC:
+	case MIPS_REVISION_SCON_SOCITSCP:
+		MSC_READ(MSC01_PCI_IACK, irq);
+		irq &= 0xff;
+		break;
+	case MIPS_REVISION_SCON_GT64120:
+		irq = GT_READ(GT_PCI0_IACK_OFS);
+		irq &= 0xff;
+		break;
+	case MIPS_REVISION_SCON_BONITO:
+		/* The following will generate a PCI IACK cycle on the
+		 * Bonito controller. It's a little bit kludgy, but it
+		 * was the easiest way to implement it in hardware at
+		 * the given time.
+		 */
+		BONITO_PCIMAP_CFG = 0x20000;
+
+		/* Flush Bonito register block */
+		(void) BONITO_PCIMAP_CFG;
+		iob();	  /* sync */
+
+		irq = __raw_readl((u32 *)_pcictrl_bonito_pcicfg);
+		iob();	  /* sync */
+		irq &= 0xff;
+		BONITO_PCIMAP_CFG = 0;
+		break;
+	default:
+		pr_emerg("Unknown system controller.\n");
+		return -1;
+	}
+	return irq;
+}
+
+static void corehi_irqdispatch(void)
+{
+	unsigned int intedge, intsteer, pcicmd, pcibadaddr;
+	unsigned int pcimstat, intisr, inten, intpol;
+	unsigned int intrcause, datalo, datahi;
+	struct pt_regs *regs = get_irq_regs();
+
+	pr_emerg("CoreHI interrupt, shouldn't happen, we die here!\n");
+	pr_emerg("epc	 : %08lx\nStatus: %08lx\n"
+		 "Cause : %08lx\nbadVaddr : %08lx\n",
+		 regs->cp0_epc, regs->cp0_status,
+		 regs->cp0_cause, regs->cp0_badvaddr);
+
+	/* Read all the registers and then print them as there is a
+	   problem with interspersed printk's upsetting the Bonito controller.
+	   Do it for the others too.
+	*/
+
+	switch (mips_revision_sconid) {
+	case MIPS_REVISION_SCON_SOCIT:
+	case MIPS_REVISION_SCON_ROCIT:
+	case MIPS_REVISION_SCON_SOCITSC:
+	case MIPS_REVISION_SCON_SOCITSCP:
+		ll_msc_irq();
+		break;
+	case MIPS_REVISION_SCON_GT64120:
+		intrcause = GT_READ(GT_INTRCAUSE_OFS);
+		datalo = GT_READ(GT_CPUERR_ADDRLO_OFS);
+		datahi = GT_READ(GT_CPUERR_ADDRHI_OFS);
+		pr_emerg("GT_INTRCAUSE = %08x\n", intrcause);
+		pr_emerg("GT_CPUERR_ADDR = %02x%08x\n",
+				datahi, datalo);
+		break;
+	case MIPS_REVISION_SCON_BONITO:
+		pcibadaddr = BONITO_PCIBADADDR;
+		pcimstat = BONITO_PCIMSTAT;
+		intisr = BONITO_INTISR;
+		inten = BONITO_INTEN;
+		intpol = BONITO_INTPOL;
+		intedge = BONITO_INTEDGE;
+		intsteer = BONITO_INTSTEER;
+		pcicmd = BONITO_PCICMD;
+		pr_emerg("BONITO_INTISR = %08x\n", intisr);
+		pr_emerg("BONITO_INTEN = %08x\n", inten);
+		pr_emerg("BONITO_INTPOL = %08x\n", intpol);
+		pr_emerg("BONITO_INTEDGE = %08x\n", intedge);
+		pr_emerg("BONITO_INTSTEER = %08x\n", intsteer);
+		pr_emerg("BONITO_PCICMD = %08x\n", pcicmd);
+		pr_emerg("BONITO_PCIBADADDR = %08x\n", pcibadaddr);
+		pr_emerg("BONITO_PCIMSTAT = %08x\n", pcimstat);
+		break;
+	}
+
+	die("CoreHi interrupt", regs);
+}
+
+static irqreturn_t corehi_handler(int irq, void *dev_id)
+{
+	corehi_irqdispatch();
+	return IRQ_HANDLED;
+}
+
+static msc_irqmap_t msc_irqmap[] __initdata = {
+	{MSC01C_INT_TMR,		MSC01_IRQ_EDGE, 0},
+	{MSC01C_INT_PCI,		MSC01_IRQ_LEVEL, 0},
+};
+static int msc_nr_irqs __initdata = ARRAY_SIZE(msc_irqmap);
+
+static msc_irqmap_t msc_eicirqmap[] __initdata = {
+	{MSC01E_INT_SW0,		MSC01_IRQ_LEVEL, 0},
+	{MSC01E_INT_SW1,		MSC01_IRQ_LEVEL, 0},
+	{MSC01E_INT_I8259A,		MSC01_IRQ_LEVEL, 0},
+	{MSC01E_INT_SMI,		MSC01_IRQ_LEVEL, 0},
+	{MSC01E_INT_COREHI,		MSC01_IRQ_LEVEL, 0},
+	{MSC01E_INT_CORELO,		MSC01_IRQ_LEVEL, 0},
+	{MSC01E_INT_TMR,		MSC01_IRQ_EDGE, 0},
+	{MSC01E_INT_PCI,		MSC01_IRQ_LEVEL, 0},
+	{MSC01E_INT_PERFCTR,		MSC01_IRQ_LEVEL, 0},
+	{MSC01E_INT_CPUCTR,		MSC01_IRQ_LEVEL, 0}
+};
+
+static int msc_nr_eicirqs __initdata = ARRAY_SIZE(msc_eicirqmap);
+
+void __init arch_init_irq(void)
+{
+	int corehi_irq;
+
+	/*
+	 * Preallocate the i8259's expected virq's here. Since irqchip_init()
+	 * will probe the irqchips in hierarchial order, i8259 is probed last.
+	 * If anything allocates a virq before the i8259 is probed, it will
+	 * be given one of the i8259's expected range and consequently setup
+	 * of the i8259 will fail.
+	 */
+	WARN(irq_alloc_descs(I8259A_IRQ_BASE, I8259A_IRQ_BASE,
+			    16, numa_node_id()) < 0,
+		"Cannot reserve i8259 virqs at IRQ%d\n", I8259A_IRQ_BASE);
+
+	i8259_set_poll(mips_pcibios_iack);
+	irqchip_init();
+
+	switch (mips_revision_sconid) {
+	case MIPS_REVISION_SCON_SOCIT:
+	case MIPS_REVISION_SCON_ROCIT:
+		if (cpu_has_veic)
+			init_msc_irqs(MIPS_MSC01_IC_REG_BASE,
+					MSC01E_INT_BASE, msc_eicirqmap,
+					msc_nr_eicirqs);
+		else
+			init_msc_irqs(MIPS_MSC01_IC_REG_BASE,
+					MSC01C_INT_BASE, msc_irqmap,
+					msc_nr_irqs);
+		break;
+
+	case MIPS_REVISION_SCON_SOCITSC:
+	case MIPS_REVISION_SCON_SOCITSCP:
+		if (cpu_has_veic)
+			init_msc_irqs(MIPS_SOCITSC_IC_REG_BASE,
+					MSC01E_INT_BASE, msc_eicirqmap,
+					msc_nr_eicirqs);
+		else
+			init_msc_irqs(MIPS_SOCITSC_IC_REG_BASE,
+					MSC01C_INT_BASE, msc_irqmap,
+					msc_nr_irqs);
+	}
+
+	if (mips_gic_present()) {
+		corehi_irq = MIPS_CPU_IRQ_BASE + MIPSCPU_INT_COREHI;
+	} else if (cpu_has_veic) {
+		set_vi_handler(MSC01E_INT_COREHI, corehi_irqdispatch);
+		corehi_irq = MSC01E_INT_BASE + MSC01E_INT_COREHI;
+	} else {
+		corehi_irq = MIPS_CPU_IRQ_BASE + MIPSCPU_INT_COREHI;
+	}
+
+	if (request_irq(corehi_irq, corehi_handler, IRQF_NO_THREAD, "CoreHi",
+			NULL))
+		pr_err("Failed to request irq %d (CoreHi)\n", corehi_irq);
+}
diff --git a/arch/mips/mti-malta/malta-memory.c b/arch/mips/mti-malta/malta-memory.c
new file mode 100644
index 000000000..952018812
--- /dev/null
+++ b/arch/mips/mti-malta/malta-memory.c
@@ -0,0 +1,44 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * PROM library functions for acquiring/using memory descriptors given to
+ * us from the YAMON.
+ *
+ * Copyright (C) 1999,2000,2012  MIPS Technologies, Inc.
+ * All rights reserved.
+ * Authors: Carsten Langgaard <carstenl@mips.com>
+ *          Steven J. Hill <sjhill@mips.com>
+ */
+#include <linux/init.h>
+#include <linux/memblock.h>
+#include <linux/string.h>
+
+#include <asm/bootinfo.h>
+#include <asm/cdmm.h>
+#include <asm/maar.h>
+#include <asm/sections.h>
+#include <asm/fw/fw.h>
+
+/* determined physical memory size, not overridden by command line args	 */
+unsigned long physical_memsize = 0L;
+
+static void free_init_pages_eva_malta(void *begin, void *end)
+{
+	free_init_pages("unused kernel", __pa_symbol((unsigned long *)begin),
+			__pa_symbol((unsigned long *)end));
+}
+
+void __init fw_meminit(void)
+{
+	bool eva = IS_ENABLED(CONFIG_EVA);
+
+	free_init_pages_eva = eva ? free_init_pages_eva_malta : NULL;
+}
+
+phys_addr_t mips_cdmm_phys_base(void)
+{
+	/* This address is "typically unused" */
+	return 0x1fc10000;
+}
diff --git a/arch/mips/mti-malta/malta-platform.c b/arch/mips/mti-malta/malta-platform.c
new file mode 100644
index 000000000..4ffbcc58c
--- /dev/null
+++ b/arch/mips/mti-malta/malta-platform.c
@@ -0,0 +1,77 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2006, 07 MIPS Technologies, Inc.
+ *   written by Ralf Baechle (ralf@linux-mips.org)
+ *     written by Ralf Baechle <ralf@linux-mips.org>
+ *
+ * Copyright (C) 2008 Wind River Systems, Inc.
+ *   updated by Tiejun Chen <tiejun.chen@windriver.com>
+ *
+ * 1. Probe driver for the Malta's UART ports:
+ *
+ *   o 2 ports in the SMC SuperIO
+ *   o 1 port in the CBUS UART, a discrete 16550 which normally is only used
+ *     for bringups.
+ *
+ * We don't use 8250_platform.c on Malta as it would result in the CBUS
+ * UART becoming ttyS0.
+ *
+ * 2. Register RTC-CMOS platform device on Malta.
+ */
+#include <linux/init.h>
+#include <linux/serial_8250.h>
+#include <linux/irq.h>
+#include <linux/platform_device.h>
+#include <asm/mips-boards/maltaint.h>
+
+#define SMC_PORT(base, int)						\
+{									\
+	.iobase		= base,						\
+	.irq		= int,						\
+	.uartclk	= 1843200,					\
+	.iotype		= UPIO_PORT,					\
+	.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST |		\
+			  UPF_MAGIC_MULTIPLIER,				\
+	.regshift	= 0,						\
+}
+
+#define CBUS_UART_FLAGS (UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_IOREMAP)
+
+static struct plat_serial8250_port uart8250_data[] = {
+	SMC_PORT(0x3F8, 4),
+	SMC_PORT(0x2F8, 3),
+#ifndef CONFIG_MIPS_CMP
+	{
+		.mapbase	= 0x1f000900,	/* The CBUS UART */
+		.irq		= MIPS_CPU_IRQ_BASE + MIPSCPU_INT_MB2,
+		.uartclk	= 3686400,	/* Twice the usual clk! */
+		.iotype		= IS_ENABLED(CONFIG_CPU_BIG_ENDIAN) ?
+				  UPIO_MEM32BE : UPIO_MEM32,
+		.flags		= CBUS_UART_FLAGS,
+		.regshift	= 3,
+	},
+#endif
+	{ },
+};
+
+static struct platform_device malta_uart8250_device = {
+	.name			= "serial8250",
+	.id			= PLAT8250_DEV_PLATFORM,
+	.dev			= {
+		.platform_data	= uart8250_data,
+	},
+};
+
+static struct platform_device *malta_devices[] __initdata = {
+	&malta_uart8250_device,
+};
+
+static int __init malta_add_devices(void)
+{
+	return platform_add_devices(malta_devices, ARRAY_SIZE(malta_devices));
+}
+
+device_initcall(malta_add_devices);
diff --git a/arch/mips/mti-malta/malta-setup.c b/arch/mips/mti-malta/malta-setup.c
new file mode 100644
index 000000000..21cb3ac12
--- /dev/null
+++ b/arch/mips/mti-malta/malta-setup.c
@@ -0,0 +1,235 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 2000 MIPS Technologies, Inc.  All rights reserved.
+ * Copyright (C) 2008 Dmitri Vorobiev
+ */
+#include <linux/cpu.h>
+#include <linux/init.h>
+#include <linux/sched.h>
+#include <linux/ioport.h>
+#include <linux/irq.h>
+#include <linux/of_fdt.h>
+#include <linux/pci.h>
+#include <linux/screen_info.h>
+#include <linux/time.h>
+#include <linux/dma-map-ops.h> /* for dma_default_coherent */
+
+#include <asm/fw/fw.h>
+#include <asm/mips-cps.h>
+#include <asm/mips-boards/generic.h>
+#include <asm/mips-boards/malta.h>
+#include <asm/mips-boards/maltaint.h>
+#include <asm/dma.h>
+#include <asm/prom.h>
+#include <asm/traps.h>
+#ifdef CONFIG_VT
+#include <linux/console.h>
+#endif
+
+#define ROCIT_CONFIG_GEN0		0x1f403000
+#define  ROCIT_CONFIG_GEN0_PCI_IOCU	BIT(7)
+
+static struct resource standard_io_resources[] = {
+	{
+		.name = "dma1",
+		.start = 0x00,
+		.end = 0x1f,
+		.flags = IORESOURCE_IO | IORESOURCE_BUSY
+	},
+	{
+		.name = "timer",
+		.start = 0x40,
+		.end = 0x5f,
+		.flags = IORESOURCE_IO | IORESOURCE_BUSY
+	},
+	{
+		.name = "keyboard",
+		.start = 0x60,
+		.end = 0x6f,
+		.flags = IORESOURCE_IO | IORESOURCE_BUSY
+	},
+	{
+		.name = "dma page reg",
+		.start = 0x80,
+		.end = 0x8f,
+		.flags = IORESOURCE_IO | IORESOURCE_BUSY
+	},
+	{
+		.name = "dma2",
+		.start = 0xc0,
+		.end = 0xdf,
+		.flags = IORESOURCE_IO | IORESOURCE_BUSY
+	},
+};
+
+const char *get_system_type(void)
+{
+	return "MIPS Malta";
+}
+
+#ifdef CONFIG_BLK_DEV_FD
+static void __init fd_activate(void)
+{
+	/*
+	 * Activate Floppy Controller in the SMSC FDC37M817 Super I/O
+	 * Controller.
+	 * Done by YAMON 2.00 onwards
+	 */
+	/* Entering config state. */
+	SMSC_WRITE(SMSC_CONFIG_ENTER, SMSC_CONFIG_REG);
+
+	/* Activate floppy controller. */
+	SMSC_WRITE(SMSC_CONFIG_DEVNUM, SMSC_CONFIG_REG);
+	SMSC_WRITE(SMSC_CONFIG_DEVNUM_FLOPPY, SMSC_DATA_REG);
+	SMSC_WRITE(SMSC_CONFIG_ACTIVATE, SMSC_CONFIG_REG);
+	SMSC_WRITE(SMSC_CONFIG_ACTIVATE_ENABLE, SMSC_DATA_REG);
+
+	/* Exit config state. */
+	SMSC_WRITE(SMSC_CONFIG_EXIT, SMSC_CONFIG_REG);
+}
+#endif
+
+static void __init plat_setup_iocoherency(void)
+{
+	u32 cfg;
+
+	if (mips_revision_sconid == MIPS_REVISION_SCON_BONITO) {
+		if (BONITO_PCICACHECTRL & BONITO_PCICACHECTRL_CPUCOH_PRES) {
+			BONITO_PCICACHECTRL |= BONITO_PCICACHECTRL_CPUCOH_EN;
+			pr_info("Enabled Bonito CPU coherency\n");
+			dma_default_coherent = true;
+		}
+		if (strstr(fw_getcmdline(), "iobcuncached")) {
+			BONITO_PCICACHECTRL &= ~BONITO_PCICACHECTRL_IOBCCOH_EN;
+			BONITO_PCIMEMBASECFG = BONITO_PCIMEMBASECFG &
+				~(BONITO_PCIMEMBASECFG_MEMBASE0_CACHED |
+				  BONITO_PCIMEMBASECFG_MEMBASE1_CACHED);
+			pr_info("Disabled Bonito IOBC coherency\n");
+		} else {
+			BONITO_PCICACHECTRL |= BONITO_PCICACHECTRL_IOBCCOH_EN;
+			BONITO_PCIMEMBASECFG |=
+				(BONITO_PCIMEMBASECFG_MEMBASE0_CACHED |
+				 BONITO_PCIMEMBASECFG_MEMBASE1_CACHED);
+			pr_info("Enabled Bonito IOBC coherency\n");
+		}
+	} else if (mips_cps_numiocu(0) != 0) {
+		/* Nothing special needs to be done to enable coherency */
+		pr_info("CMP IOCU detected\n");
+		cfg = __raw_readl((u32 *)CKSEG1ADDR(ROCIT_CONFIG_GEN0));
+		if (cfg & ROCIT_CONFIG_GEN0_PCI_IOCU)
+			dma_default_coherent = true;
+		else
+			pr_crit("IOCU OPERATION DISABLED BY SWITCH - DEFAULTING TO SW IO COHERENCY\n");
+	}
+
+	if (dma_default_coherent)
+		pr_info("Hardware DMA cache coherency enabled\n");
+	else
+		pr_info("Software DMA cache coherency enabled\n");
+}
+
+static void __init pci_clock_check(void)
+{
+	unsigned int __iomem *jmpr_p =
+		(unsigned int *) ioremap(MALTA_JMPRS_REG, sizeof(unsigned int));
+	int jmpr = (__raw_readl(jmpr_p) >> 2) & 0x07;
+	static const int pciclocks[] __initconst = {
+		33, 20, 25, 30, 12, 16, 37, 10
+	};
+	int pciclock = pciclocks[jmpr];
+	char *optptr, *argptr = fw_getcmdline();
+
+	/*
+	 * If user passed a pci_clock= option, don't tack on another one
+	 */
+	optptr = strstr(argptr, "pci_clock=");
+	if (optptr && (optptr == argptr || optptr[-1] == ' '))
+		return;
+
+	if (pciclock != 33) {
+		pr_warn("WARNING: PCI clock is %dMHz, setting pci_clock\n",
+			pciclock);
+		argptr += strlen(argptr);
+		sprintf(argptr, " pci_clock=%d", pciclock);
+		if (pciclock < 20 || pciclock > 66)
+			pr_warn("WARNING: IDE timing calculations will be "
+			        "incorrect\n");
+	}
+}
+
+#if defined(CONFIG_VT) && defined(CONFIG_VGA_CONSOLE)
+static void __init screen_info_setup(void)
+{
+	screen_info = (struct screen_info) {
+		.orig_x = 0,
+		.orig_y = 25,
+		.ext_mem_k = 0,
+		.orig_video_page = 0,
+		.orig_video_mode = 0,
+		.orig_video_cols = 80,
+		.unused2 = 0,
+		.orig_video_ega_bx = 0,
+		.unused3 = 0,
+		.orig_video_lines = 25,
+		.orig_video_isVGA = VIDEO_TYPE_VGAC,
+		.orig_video_points = 16
+	};
+}
+#endif
+
+static void __init bonito_quirks_setup(void)
+{
+	char *argptr;
+
+	argptr = fw_getcmdline();
+	if (strstr(argptr, "debug")) {
+		BONITO_BONGENCFG |= BONITO_BONGENCFG_DEBUGMODE;
+		pr_info("Enabled Bonito debug mode\n");
+	} else
+		BONITO_BONGENCFG &= ~BONITO_BONGENCFG_DEBUGMODE;
+}
+
+void __init *plat_get_fdt(void)
+{
+	return (void *)__dtb_start;
+}
+
+void __init plat_mem_setup(void)
+{
+	unsigned int i;
+	void *fdt = plat_get_fdt();
+
+	fdt = malta_dt_shim(fdt);
+	__dt_setup_arch(fdt);
+
+	if (IS_ENABLED(CONFIG_EVA))
+		/* EVA has already been configured in mach-malta/kernel-init.h */
+		pr_info("Enhanced Virtual Addressing (EVA) activated\n");
+
+	mips_pcibios_init();
+
+	/* Request I/O space for devices used on the Malta board. */
+	for (i = 0; i < ARRAY_SIZE(standard_io_resources); i++)
+		request_resource(&ioport_resource, standard_io_resources+i);
+
+	/*
+	 * Enable DMA channel 4 (cascade channel) in the PIIX4 south bridge.
+	 */
+	enable_dma(4);
+
+	if (mips_revision_sconid == MIPS_REVISION_SCON_BONITO)
+		bonito_quirks_setup();
+
+	plat_setup_iocoherency();
+
+	pci_clock_check();
+
+#ifdef CONFIG_BLK_DEV_FD
+	fd_activate();
+#endif
+
+#if defined(CONFIG_VT) && defined(CONFIG_VGA_CONSOLE)
+	screen_info_setup();
+#endif
+}
diff --git a/arch/mips/mti-malta/malta-time.c b/arch/mips/mti-malta/malta-time.c
new file mode 100644
index 000000000..2cb708cdf
--- /dev/null
+++ b/arch/mips/mti-malta/malta-time.c
@@ -0,0 +1,253 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 1999,2000 MIPS Technologies, Inc.  All rights reserved.
+ *
+ * Setting up the clock on the MIPS boards.
+ */
+#include <linux/types.h>
+#include <linux/i8253.h>
+#include <linux/init.h>
+#include <linux/kernel_stat.h>
+#include <linux/libfdt.h>
+#include <linux/math64.h>
+#include <linux/sched.h>
+#include <linux/spinlock.h>
+#include <linux/interrupt.h>
+#include <linux/timex.h>
+#include <linux/mc146818rtc.h>
+
+#include <asm/cpu.h>
+#include <asm/mipsregs.h>
+#include <asm/mipsmtregs.h>
+#include <asm/hardirq.h>
+#include <asm/irq.h>
+#include <asm/div64.h>
+#include <asm/setup.h>
+#include <asm/time.h>
+#include <asm/mc146818-time.h>
+#include <asm/msc01_ic.h>
+#include <asm/mips-cps.h>
+
+#include <asm/mips-boards/generic.h>
+#include <asm/mips-boards/maltaint.h>
+
+static int mips_cpu_timer_irq;
+static int mips_cpu_perf_irq;
+extern int cp0_perfcount_irq;
+
+static unsigned int gic_frequency;
+
+static void mips_timer_dispatch(void)
+{
+	do_IRQ(mips_cpu_timer_irq);
+}
+
+static void mips_perf_dispatch(void)
+{
+	do_IRQ(mips_cpu_perf_irq);
+}
+
+static unsigned int freqround(unsigned int freq, unsigned int amount)
+{
+	freq += amount;
+	freq -= freq % (amount*2);
+	return freq;
+}
+
+/*
+ * Estimate CPU and GIC frequencies.
+ */
+static void __init estimate_frequencies(void)
+{
+	unsigned long flags;
+	unsigned int count, start;
+	unsigned char secs1, secs2, ctrl;
+	int secs;
+	u64 giccount = 0, gicstart = 0;
+
+	local_irq_save(flags);
+
+	if (mips_gic_present())
+		clear_gic_config(GIC_CONFIG_COUNTSTOP);
+
+	/*
+	 * Read counters exactly on rising edge of update flag.
+	 * This helps get an accurate reading under virtualisation.
+	 */
+	while (CMOS_READ(RTC_REG_A) & RTC_UIP);
+	while (!(CMOS_READ(RTC_REG_A) & RTC_UIP));
+	start = read_c0_count();
+	if (mips_gic_present())
+		gicstart = read_gic_counter();
+
+	/* Wait for falling edge before reading RTC. */
+	while (CMOS_READ(RTC_REG_A) & RTC_UIP);
+	secs1 = CMOS_READ(RTC_SECONDS);
+
+	/* Read counters again exactly on rising edge of update flag. */
+	while (!(CMOS_READ(RTC_REG_A) & RTC_UIP));
+	count = read_c0_count();
+	if (mips_gic_present())
+		giccount = read_gic_counter();
+
+	/* Wait for falling edge before reading RTC again. */
+	while (CMOS_READ(RTC_REG_A) & RTC_UIP);
+	secs2 = CMOS_READ(RTC_SECONDS);
+
+	ctrl = CMOS_READ(RTC_CONTROL);
+
+	local_irq_restore(flags);
+
+	if (!(ctrl & RTC_DM_BINARY) || RTC_ALWAYS_BCD) {
+		secs1 = bcd2bin(secs1);
+		secs2 = bcd2bin(secs2);
+	}
+	secs = secs2 - secs1;
+	if (secs < 1)
+		secs += 60;
+
+	count -= start;
+	count /= secs;
+	mips_hpt_frequency = count;
+
+	if (mips_gic_present()) {
+		giccount = div_u64(giccount - gicstart, secs);
+		gic_frequency = giccount;
+	}
+}
+
+void read_persistent_clock64(struct timespec64 *ts)
+{
+	ts->tv_sec = mc146818_get_cmos_time();
+	ts->tv_nsec = 0;
+}
+
+int get_c0_fdc_int(void)
+{
+	/*
+	 * Some cores claim the FDC is routable through the GIC, but it doesn't
+	 * actually seem to be connected for those Malta bitstreams.
+	 */
+	switch (current_cpu_type()) {
+	case CPU_INTERAPTIV:
+	case CPU_PROAPTIV:
+		return -1;
+	}
+
+	if (cpu_has_veic)
+		return -1;
+	else if (mips_gic_present())
+		return gic_get_c0_fdc_int();
+	else if (cp0_fdc_irq >= 0)
+		return MIPS_CPU_IRQ_BASE + cp0_fdc_irq;
+	else
+		return -1;
+}
+
+int get_c0_perfcount_int(void)
+{
+	if (cpu_has_veic) {
+		set_vi_handler(MSC01E_INT_PERFCTR, mips_perf_dispatch);
+		mips_cpu_perf_irq = MSC01E_INT_BASE + MSC01E_INT_PERFCTR;
+	} else if (mips_gic_present()) {
+		mips_cpu_perf_irq = gic_get_c0_perfcount_int();
+	} else if (cp0_perfcount_irq >= 0) {
+		mips_cpu_perf_irq = MIPS_CPU_IRQ_BASE + cp0_perfcount_irq;
+	} else {
+		mips_cpu_perf_irq = -1;
+	}
+
+	return mips_cpu_perf_irq;
+}
+EXPORT_SYMBOL_GPL(get_c0_perfcount_int);
+
+unsigned int get_c0_compare_int(void)
+{
+	if (cpu_has_veic) {
+		set_vi_handler(MSC01E_INT_CPUCTR, mips_timer_dispatch);
+		mips_cpu_timer_irq = MSC01E_INT_BASE + MSC01E_INT_CPUCTR;
+	} else if (mips_gic_present()) {
+		mips_cpu_timer_irq = gic_get_c0_compare_int();
+	} else {
+		mips_cpu_timer_irq = MIPS_CPU_IRQ_BASE + cp0_compare_irq;
+	}
+
+	return mips_cpu_timer_irq;
+}
+
+static void __init init_rtc(void)
+{
+	unsigned char freq, ctrl;
+
+	/* Set 32KHz time base if not already set */
+	freq = CMOS_READ(RTC_FREQ_SELECT);
+	if ((freq & RTC_DIV_CTL) != RTC_REF_CLCK_32KHZ)
+		CMOS_WRITE(RTC_REF_CLCK_32KHZ, RTC_FREQ_SELECT);
+
+	/* Ensure SET bit is clear so RTC can run */
+	ctrl = CMOS_READ(RTC_CONTROL);
+	if (ctrl & RTC_SET)
+		CMOS_WRITE(ctrl & ~RTC_SET, RTC_CONTROL);
+}
+
+#ifdef CONFIG_CLKSRC_MIPS_GIC
+static u32 gic_frequency_dt;
+
+static struct property gic_frequency_prop = {
+	.name = "clock-frequency",
+	.length = sizeof(u32),
+	.value = &gic_frequency_dt,
+};
+
+static void update_gic_frequency_dt(void)
+{
+	struct device_node *node;
+
+	gic_frequency_dt = cpu_to_be32(gic_frequency);
+
+	node = of_find_compatible_node(NULL, NULL, "mti,gic-timer");
+	if (!node) {
+		pr_err("mti,gic-timer device node not found\n");
+		return;
+	}
+
+	if (of_update_property(node, &gic_frequency_prop) < 0)
+		pr_err("error updating gic frequency property\n");
+
+	of_node_put(node);
+}
+
+#endif
+
+void __init plat_time_init(void)
+{
+	unsigned int prid = read_c0_prid() & (PRID_COMP_MASK | PRID_IMP_MASK);
+	unsigned int freq;
+
+	init_rtc();
+	estimate_frequencies();
+
+	freq = mips_hpt_frequency;
+	if ((prid != (PRID_COMP_MIPS | PRID_IMP_20KC)) &&
+	    (prid != (PRID_COMP_MIPS | PRID_IMP_25KF)))
+		freq *= 2;
+	freq = freqround(freq, 5000);
+	printk("CPU frequency %d.%02d MHz\n", freq/1000000,
+	       (freq%1000000)*100/1000000);
+
+#ifdef CONFIG_I8253
+	/* Only Malta has a PIT. */
+	setup_pit_timer();
+#endif
+
+	if (mips_gic_present()) {
+		freq = freqround(gic_frequency, 5000);
+		printk("GIC frequency %d.%02d MHz\n", freq/1000000,
+		       (freq%1000000)*100/1000000);
+#ifdef CONFIG_CLKSRC_MIPS_GIC
+		update_gic_frequency_dt();
+		timer_probe();
+#endif
+	}
+}
diff --git a/arch/mips/n64/Makefile b/arch/mips/n64/Makefile
new file mode 100644
index 000000000..b64a05ae2
--- /dev/null
+++ b/arch/mips/n64/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Nintendo 64
+#
+
+obj-y := init.o irq.o
diff --git a/arch/mips/n64/Platform b/arch/mips/n64/Platform
new file mode 100644
index 000000000..246478313
--- /dev/null
+++ b/arch/mips/n64/Platform
@@ -0,0 +1,7 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Nintendo 64
+#
+
+cflags-$(CONFIG_MACH_NINTENDO64)    += -I$(srctree)/arch/mips/include/asm/mach-n64
+load-$(CONFIG_MACH_NINTENDO64)      += 0xffffffff80101000
diff --git a/arch/mips/n64/init.c b/arch/mips/n64/init.c
new file mode 100644
index 000000000..dfbd864f4
--- /dev/null
+++ b/arch/mips/n64/init.c
@@ -0,0 +1,164 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ *  Nintendo 64 init.
+ *
+ *  Copyright (C) 2021	Lauri Kasanen
+ */
+#include <linux/init.h>
+#include <linux/ioport.h>
+#include <linux/irq.h>
+#include <linux/memblock.h>
+#include <linux/platform_device.h>
+#include <linux/platform_data/simplefb.h>
+#include <linux/string.h>
+
+#include <asm/bootinfo.h>
+#include <asm/fw/fw.h>
+#include <asm/time.h>
+
+#define IO_MEM_RESOURCE_START	0UL
+#define IO_MEM_RESOURCE_END	0x1fffffffUL
+
+/*
+ * System-specifc irq names for clarity
+ */
+#define MIPS_CPU_IRQ(x)		(MIPS_CPU_IRQ_BASE + (x))
+#define MIPS_SOFTINT0_IRQ	MIPS_CPU_IRQ(0)
+#define MIPS_SOFTINT1_IRQ	MIPS_CPU_IRQ(1)
+#define RCP_IRQ			MIPS_CPU_IRQ(2)
+#define CART_IRQ		MIPS_CPU_IRQ(3)
+#define PRENMI_IRQ		MIPS_CPU_IRQ(4)
+#define RDBR_IRQ		MIPS_CPU_IRQ(5)
+#define RDBW_IRQ		MIPS_CPU_IRQ(6)
+#define TIMER_IRQ		MIPS_CPU_IRQ(7)
+
+static void __init iomem_resource_init(void)
+{
+	iomem_resource.start = IO_MEM_RESOURCE_START;
+	iomem_resource.end = IO_MEM_RESOURCE_END;
+}
+
+const char *get_system_type(void)
+{
+	return "Nintendo 64";
+}
+
+void __init prom_init(void)
+{
+	fw_init_cmdline();
+}
+
+#define W 320
+#define H 240
+#define REG_BASE ((u32 *) CKSEG1ADDR(0x4400000))
+
+static void __init n64rdp_write_reg(const u8 reg, const u32 value)
+{
+	__raw_writel(value, REG_BASE + reg);
+}
+
+#undef REG_BASE
+
+static const u32 ntsc_320[] __initconst = {
+	0x00013212, 0x00000000, 0x00000140, 0x00000200,
+	0x00000000, 0x03e52239, 0x0000020d, 0x00000c15,
+	0x0c150c15, 0x006c02ec, 0x002501ff, 0x000e0204,
+	0x00000200, 0x00000400
+};
+
+#define MI_REG_BASE 0x4300000
+#define NUM_MI_REGS 4
+#define AI_REG_BASE 0x4500000
+#define NUM_AI_REGS 6
+#define PI_REG_BASE 0x4600000
+#define NUM_PI_REGS 5
+#define SI_REG_BASE 0x4800000
+#define NUM_SI_REGS 7
+
+static int __init n64_platform_init(void)
+{
+	static const char simplefb_resname[] = "FB";
+	static const struct simplefb_platform_data mode = {
+		.width = W,
+		.height = H,
+		.stride = W * 2,
+		.format = "r5g5b5a1"
+	};
+	struct resource res[3];
+	void *orig;
+	unsigned long phys;
+	unsigned i;
+
+	memset(res, 0, sizeof(struct resource) * 3);
+	res[0].flags = IORESOURCE_MEM;
+	res[0].start = MI_REG_BASE;
+	res[0].end = MI_REG_BASE + NUM_MI_REGS * 4 - 1;
+
+	res[1].flags = IORESOURCE_MEM;
+	res[1].start = AI_REG_BASE;
+	res[1].end = AI_REG_BASE + NUM_AI_REGS * 4 - 1;
+
+	res[2].flags = IORESOURCE_IRQ;
+	res[2].start = RCP_IRQ;
+	res[2].end = RCP_IRQ;
+
+	platform_device_register_simple("n64audio", -1, res, 3);
+
+	memset(&res[0], 0, sizeof(res[0]));
+	res[0].flags = IORESOURCE_MEM;
+	res[0].start = PI_REG_BASE;
+	res[0].end = PI_REG_BASE + NUM_PI_REGS * 4 - 1;
+
+	platform_device_register_simple("n64cart", -1, res, 1);
+
+	memset(&res[0], 0, sizeof(res[0]));
+	res[0].flags = IORESOURCE_MEM;
+	res[0].start = SI_REG_BASE;
+	res[0].end = SI_REG_BASE + NUM_SI_REGS * 4 - 1;
+
+	platform_device_register_simple("n64joy", -1, res, 1);
+
+	/* The framebuffer needs 64-byte alignment */
+	orig = kzalloc(W * H * 2 + 63, GFP_DMA | GFP_KERNEL);
+	if (!orig)
+		return -ENOMEM;
+	phys = virt_to_phys(orig);
+	phys += 63;
+	phys &= ~63;
+
+	for (i = 0; i < ARRAY_SIZE(ntsc_320); i++) {
+		if (i == 1)
+			n64rdp_write_reg(i, phys);
+		else
+			n64rdp_write_reg(i, ntsc_320[i]);
+	}
+
+	/* setup IORESOURCE_MEM as framebuffer memory */
+	memset(&res[0], 0, sizeof(res[0]));
+	res[0].flags = IORESOURCE_MEM;
+	res[0].name = simplefb_resname;
+	res[0].start = phys;
+	res[0].end = phys + W * H * 2 - 1;
+
+	platform_device_register_resndata(NULL, "simple-framebuffer", 0,
+					  &res[0], 1, &mode, sizeof(mode));
+
+	return 0;
+}
+
+#undef W
+#undef H
+
+arch_initcall(n64_platform_init);
+
+void __init plat_mem_setup(void)
+{
+	iomem_resource_init();
+	memblock_add(0x0, 8 * 1024 * 1024); /* Bootloader blocks the 4mb config */
+}
+
+void __init plat_time_init(void)
+{
+	/* 93.75 MHz cpu, count register runs at half rate */
+	mips_hpt_frequency = 93750000 / 2;
+}
diff --git a/arch/mips/n64/irq.c b/arch/mips/n64/irq.c
new file mode 100644
index 000000000..1861e962d
--- /dev/null
+++ b/arch/mips/n64/irq.c
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ *  N64 IRQ
+ *
+ *  Copyright (C) 2021 Lauri Kasanen
+ */
+#include <linux/export.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+
+#include <asm/irq_cpu.h>
+
+void __init arch_init_irq(void)
+{
+	mips_cpu_irq_init();
+}
diff --git a/arch/mips/net/Makefile b/arch/mips/net/Makefile
new file mode 100644
index 000000000..e3e6ae651
--- /dev/null
+++ b/arch/mips/net/Makefile
@@ -0,0 +1,10 @@
+# SPDX-License-Identifier: GPL-2.0-only
+# MIPS networking code
+
+obj-$(CONFIG_BPF_JIT) += bpf_jit_comp.o
+
+ifeq ($(CONFIG_32BIT),y)
+        obj-$(CONFIG_BPF_JIT) += bpf_jit_comp32.o
+else
+        obj-$(CONFIG_BPF_JIT) += bpf_jit_comp64.o
+endif
diff --git a/arch/mips/net/bpf_jit_comp.c b/arch/mips/net/bpf_jit_comp.c
new file mode 100644
index 000000000..b17130d51
--- /dev/null
+++ b/arch/mips/net/bpf_jit_comp.c
@@ -0,0 +1,1034 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Just-In-Time compiler for eBPF bytecode on MIPS.
+ * Implementation of JIT functions common to 32-bit and 64-bit CPUs.
+ *
+ * Copyright (c) 2021 Anyfi Networks AB.
+ * Author: Johan Almbladh <johan.almbladh@gmail.com>
+ *
+ * Based on code and ideas from
+ * Copyright (c) 2017 Cavium, Inc.
+ * Copyright (c) 2017 Shubham Bansal <illusionist.neo@gmail.com>
+ * Copyright (c) 2011 Mircea Gherzan <mgherzan@gmail.com>
+ */
+
+/*
+ * Code overview
+ * =============
+ *
+ * - bpf_jit_comp.h
+ *   Common definitions and utilities.
+ *
+ * - bpf_jit_comp.c
+ *   Implementation of JIT top-level logic and exported JIT API functions.
+ *   Implementation of internal operations shared by 32-bit and 64-bit code.
+ *   JMP and ALU JIT control code, register control code, shared ALU and
+ *   JMP/JMP32 JIT operations.
+ *
+ * - bpf_jit_comp32.c
+ *   Implementation of functions to JIT prologue, epilogue and a single eBPF
+ *   instruction for 32-bit MIPS CPUs. The functions use shared operations
+ *   where possible, and implement the rest for 32-bit MIPS such as ALU64
+ *   operations.
+ *
+ * - bpf_jit_comp64.c
+ *   Ditto, for 64-bit MIPS CPUs.
+ *
+ * Zero and sign extension
+ * ========================
+ * 32-bit MIPS instructions on 64-bit MIPS registers use sign extension,
+ * but the eBPF instruction set mandates zero extension. We let the verifier
+ * insert explicit zero-extensions after 32-bit ALU operations, both for
+ * 32-bit and 64-bit MIPS JITs. Conditional JMP32 operations on 64-bit MIPs
+ * are JITed with sign extensions inserted when so expected.
+ *
+ * ALU operations
+ * ==============
+ * ALU operations on 32/64-bit MIPS and ALU64 operations on 64-bit MIPS are
+ * JITed in the following steps. ALU64 operations on 32-bit MIPS are more
+ * complicated and therefore only processed by special implementations in
+ * step (3).
+ *
+ * 1) valid_alu_i:
+ *    Determine if an immediate operation can be emitted as such, or if
+ *    we must fall back to the register version.
+ *
+ * 2) rewrite_alu_i:
+ *    Convert BPF operation and immediate value to a canonical form for
+ *    JITing. In some degenerate cases this form may be a no-op.
+ *
+ * 3) emit_alu_{i,i64,r,64}:
+ *    Emit instructions for an ALU or ALU64 immediate or register operation.
+ *
+ * JMP operations
+ * ==============
+ * JMP and JMP32 operations require an JIT instruction offset table for
+ * translating the jump offset. This table is computed by dry-running the
+ * JIT without actually emitting anything. However, the computed PC-relative
+ * offset may overflow the 18-bit offset field width of the native MIPS
+ * branch instruction. In such cases, the long jump is converted into the
+ * following sequence.
+ *
+ *    <branch> !<cond> +2    Inverted PC-relative branch
+ *    nop                    Delay slot
+ *    j <offset>             Unconditional absolute long jump
+ *    nop                    Delay slot
+ *
+ * Since this converted sequence alters the offset table, all offsets must
+ * be re-calculated. This may in turn trigger new branch conversions, so
+ * the process is repeated until no further changes are made. Normally it
+ * completes in 1-2 iterations. If JIT_MAX_ITERATIONS should reached, we
+ * fall back to converting every remaining jump operation. The branch
+ * conversion is independent of how the JMP or JMP32 condition is JITed.
+ *
+ * JMP32 and JMP operations are JITed as follows.
+ *
+ * 1) setup_jmp_{i,r}:
+ *    Convert jump conditional and offset into a form that can be JITed.
+ *    This form may be a no-op, a canonical form, or an inverted PC-relative
+ *    jump if branch conversion is necessary.
+ *
+ * 2) valid_jmp_i:
+ *    Determine if an immediate operations can be emitted as such, or if
+ *    we must fall back to the register version. Applies to JMP32 for 32-bit
+ *    MIPS, and both JMP and JMP32 for 64-bit MIPS.
+ *
+ * 3) emit_jmp_{i,i64,r,r64}:
+ *    Emit instructions for an JMP or JMP32 immediate or register operation.
+ *
+ * 4) finish_jmp_{i,r}:
+ *    Emit any instructions needed to finish the jump. This includes a nop
+ *    for the delay slot if a branch was emitted, and a long absolute jump
+ *    if the branch was converted.
+ */
+
+#include <linux/limits.h>
+#include <linux/bitops.h>
+#include <linux/errno.h>
+#include <linux/filter.h>
+#include <linux/bpf.h>
+#include <linux/slab.h>
+#include <asm/bitops.h>
+#include <asm/cacheflush.h>
+#include <asm/cpu-features.h>
+#include <asm/isa-rev.h>
+#include <asm/uasm.h>
+
+#include "bpf_jit_comp.h"
+
+/* Convenience macros for descriptor access */
+#define CONVERTED(desc)	((desc) & JIT_DESC_CONVERT)
+#define INDEX(desc)	((desc) & ~JIT_DESC_CONVERT)
+
+/*
+ * Push registers on the stack, starting at a given depth from the stack
+ * pointer and increasing. The next depth to be written is returned.
+ */
+int push_regs(struct jit_context *ctx, u32 mask, u32 excl, int depth)
+{
+	int reg;
+
+	for (reg = 0; reg < BITS_PER_BYTE * sizeof(mask); reg++)
+		if (mask & BIT(reg)) {
+			if ((excl & BIT(reg)) == 0) {
+				if (sizeof(long) == 4)
+					emit(ctx, sw, reg, depth, MIPS_R_SP);
+				else /* sizeof(long) == 8 */
+					emit(ctx, sd, reg, depth, MIPS_R_SP);
+			}
+			depth += sizeof(long);
+		}
+
+	ctx->stack_used = max((int)ctx->stack_used, depth);
+	return depth;
+}
+
+/*
+ * Pop registers from the stack, starting at a given depth from the stack
+ * pointer and increasing. The next depth to be read is returned.
+ */
+int pop_regs(struct jit_context *ctx, u32 mask, u32 excl, int depth)
+{
+	int reg;
+
+	for (reg = 0; reg < BITS_PER_BYTE * sizeof(mask); reg++)
+		if (mask & BIT(reg)) {
+			if ((excl & BIT(reg)) == 0) {
+				if (sizeof(long) == 4)
+					emit(ctx, lw, reg, depth, MIPS_R_SP);
+				else /* sizeof(long) == 8 */
+					emit(ctx, ld, reg, depth, MIPS_R_SP);
+			}
+			depth += sizeof(long);
+		}
+
+	return depth;
+}
+
+/* Compute the 28-bit jump target address from a BPF program location */
+int get_target(struct jit_context *ctx, u32 loc)
+{
+	u32 index = INDEX(ctx->descriptors[loc]);
+	unsigned long pc = (unsigned long)&ctx->target[ctx->jit_index];
+	unsigned long addr = (unsigned long)&ctx->target[index];
+
+	if (!ctx->target)
+		return 0;
+
+	if ((addr ^ pc) & ~MIPS_JMP_MASK)
+		return -1;
+
+	return addr & MIPS_JMP_MASK;
+}
+
+/* Compute the PC-relative offset to relative BPF program offset */
+int get_offset(const struct jit_context *ctx, int off)
+{
+	return (INDEX(ctx->descriptors[ctx->bpf_index + off]) -
+		ctx->jit_index - 1) * sizeof(u32);
+}
+
+/* dst = imm (register width) */
+void emit_mov_i(struct jit_context *ctx, u8 dst, s32 imm)
+{
+	if (imm >= -0x8000 && imm <= 0x7fff) {
+		emit(ctx, addiu, dst, MIPS_R_ZERO, imm);
+	} else {
+		emit(ctx, lui, dst, (s16)((u32)imm >> 16));
+		emit(ctx, ori, dst, dst, (u16)(imm & 0xffff));
+	}
+	clobber_reg(ctx, dst);
+}
+
+/* dst = src (register width) */
+void emit_mov_r(struct jit_context *ctx, u8 dst, u8 src)
+{
+	emit(ctx, ori, dst, src, 0);
+	clobber_reg(ctx, dst);
+}
+
+/* Validate ALU immediate range */
+bool valid_alu_i(u8 op, s32 imm)
+{
+	switch (BPF_OP(op)) {
+	case BPF_NEG:
+	case BPF_LSH:
+	case BPF_RSH:
+	case BPF_ARSH:
+		/* All legal eBPF values are valid */
+		return true;
+	case BPF_ADD:
+		/* imm must be 16 bits */
+		return imm >= -0x8000 && imm <= 0x7fff;
+	case BPF_SUB:
+		/* -imm must be 16 bits */
+		return imm >= -0x7fff && imm <= 0x8000;
+	case BPF_AND:
+	case BPF_OR:
+	case BPF_XOR:
+		/* imm must be 16 bits unsigned */
+		return imm >= 0 && imm <= 0xffff;
+	case BPF_MUL:
+		/* imm must be zero or a positive power of two */
+		return imm == 0 || (imm > 0 && is_power_of_2(imm));
+	case BPF_DIV:
+	case BPF_MOD:
+		/* imm must be an 17-bit power of two */
+		return (u32)imm <= 0x10000 && is_power_of_2((u32)imm);
+	}
+	return false;
+}
+
+/* Rewrite ALU immediate operation */
+bool rewrite_alu_i(u8 op, s32 imm, u8 *alu, s32 *val)
+{
+	bool act = true;
+
+	switch (BPF_OP(op)) {
+	case BPF_LSH:
+	case BPF_RSH:
+	case BPF_ARSH:
+	case BPF_ADD:
+	case BPF_SUB:
+	case BPF_OR:
+	case BPF_XOR:
+		/* imm == 0 is a no-op */
+		act = imm != 0;
+		break;
+	case BPF_MUL:
+		if (imm == 1) {
+			/* dst * 1 is a no-op */
+			act = false;
+		} else if (imm == 0) {
+			/* dst * 0 is dst & 0 */
+			op = BPF_AND;
+		} else {
+			/* dst * (1 << n) is dst << n */
+			op = BPF_LSH;
+			imm = ilog2(abs(imm));
+		}
+		break;
+	case BPF_DIV:
+		if (imm == 1) {
+			/* dst / 1 is a no-op */
+			act = false;
+		} else {
+			/* dst / (1 << n) is dst >> n */
+			op = BPF_RSH;
+			imm = ilog2(imm);
+		}
+		break;
+	case BPF_MOD:
+		/* dst % (1 << n) is dst & ((1 << n) - 1) */
+		op = BPF_AND;
+		imm--;
+		break;
+	}
+
+	*alu = op;
+	*val = imm;
+	return act;
+}
+
+/* ALU immediate operation (32-bit) */
+void emit_alu_i(struct jit_context *ctx, u8 dst, s32 imm, u8 op)
+{
+	switch (BPF_OP(op)) {
+	/* dst = -dst */
+	case BPF_NEG:
+		emit(ctx, subu, dst, MIPS_R_ZERO, dst);
+		break;
+	/* dst = dst & imm */
+	case BPF_AND:
+		emit(ctx, andi, dst, dst, (u16)imm);
+		break;
+	/* dst = dst | imm */
+	case BPF_OR:
+		emit(ctx, ori, dst, dst, (u16)imm);
+		break;
+	/* dst = dst ^ imm */
+	case BPF_XOR:
+		emit(ctx, xori, dst, dst, (u16)imm);
+		break;
+	/* dst = dst << imm */
+	case BPF_LSH:
+		emit(ctx, sll, dst, dst, imm);
+		break;
+	/* dst = dst >> imm */
+	case BPF_RSH:
+		emit(ctx, srl, dst, dst, imm);
+		break;
+	/* dst = dst >> imm (arithmetic) */
+	case BPF_ARSH:
+		emit(ctx, sra, dst, dst, imm);
+		break;
+	/* dst = dst + imm */
+	case BPF_ADD:
+		emit(ctx, addiu, dst, dst, imm);
+		break;
+	/* dst = dst - imm */
+	case BPF_SUB:
+		emit(ctx, addiu, dst, dst, -imm);
+		break;
+	}
+	clobber_reg(ctx, dst);
+}
+
+/* ALU register operation (32-bit) */
+void emit_alu_r(struct jit_context *ctx, u8 dst, u8 src, u8 op)
+{
+	switch (BPF_OP(op)) {
+	/* dst = dst & src */
+	case BPF_AND:
+		emit(ctx, and, dst, dst, src);
+		break;
+	/* dst = dst | src */
+	case BPF_OR:
+		emit(ctx, or, dst, dst, src);
+		break;
+	/* dst = dst ^ src */
+	case BPF_XOR:
+		emit(ctx, xor, dst, dst, src);
+		break;
+	/* dst = dst << src */
+	case BPF_LSH:
+		emit(ctx, sllv, dst, dst, src);
+		break;
+	/* dst = dst >> src */
+	case BPF_RSH:
+		emit(ctx, srlv, dst, dst, src);
+		break;
+	/* dst = dst >> src (arithmetic) */
+	case BPF_ARSH:
+		emit(ctx, srav, dst, dst, src);
+		break;
+	/* dst = dst + src */
+	case BPF_ADD:
+		emit(ctx, addu, dst, dst, src);
+		break;
+	/* dst = dst - src */
+	case BPF_SUB:
+		emit(ctx, subu, dst, dst, src);
+		break;
+	/* dst = dst * src */
+	case BPF_MUL:
+		if (cpu_has_mips32r1 || cpu_has_mips32r6) {
+			emit(ctx, mul, dst, dst, src);
+		} else {
+			emit(ctx, multu, dst, src);
+			emit(ctx, mflo, dst);
+		}
+		break;
+	/* dst = dst / src */
+	case BPF_DIV:
+		if (cpu_has_mips32r6) {
+			emit(ctx, divu_r6, dst, dst, src);
+		} else {
+			emit(ctx, divu, dst, src);
+			emit(ctx, mflo, dst);
+		}
+		break;
+	/* dst = dst % src */
+	case BPF_MOD:
+		if (cpu_has_mips32r6) {
+			emit(ctx, modu, dst, dst, src);
+		} else {
+			emit(ctx, divu, dst, src);
+			emit(ctx, mfhi, dst);
+		}
+		break;
+	}
+	clobber_reg(ctx, dst);
+}
+
+/* Atomic read-modify-write (32-bit) */
+void emit_atomic_r(struct jit_context *ctx, u8 dst, u8 src, s16 off, u8 code)
+{
+	LLSC_sync(ctx);
+	emit(ctx, ll, MIPS_R_T9, off, dst);
+	switch (code) {
+	case BPF_ADD:
+	case BPF_ADD | BPF_FETCH:
+		emit(ctx, addu, MIPS_R_T8, MIPS_R_T9, src);
+		break;
+	case BPF_AND:
+	case BPF_AND | BPF_FETCH:
+		emit(ctx, and, MIPS_R_T8, MIPS_R_T9, src);
+		break;
+	case BPF_OR:
+	case BPF_OR | BPF_FETCH:
+		emit(ctx, or, MIPS_R_T8, MIPS_R_T9, src);
+		break;
+	case BPF_XOR:
+	case BPF_XOR | BPF_FETCH:
+		emit(ctx, xor, MIPS_R_T8, MIPS_R_T9, src);
+		break;
+	case BPF_XCHG:
+		emit(ctx, move, MIPS_R_T8, src);
+		break;
+	}
+	emit(ctx, sc, MIPS_R_T8, off, dst);
+	emit(ctx, LLSC_beqz, MIPS_R_T8, -16 - LLSC_offset);
+	emit(ctx, nop); /* Delay slot */
+
+	if (code & BPF_FETCH) {
+		emit(ctx, move, src, MIPS_R_T9);
+		clobber_reg(ctx, src);
+	}
+}
+
+/* Atomic compare-and-exchange (32-bit) */
+void emit_cmpxchg_r(struct jit_context *ctx, u8 dst, u8 src, u8 res, s16 off)
+{
+	LLSC_sync(ctx);
+	emit(ctx, ll, MIPS_R_T9, off, dst);
+	emit(ctx, bne, MIPS_R_T9, res, 12);
+	emit(ctx, move, MIPS_R_T8, src);     /* Delay slot */
+	emit(ctx, sc, MIPS_R_T8, off, dst);
+	emit(ctx, LLSC_beqz, MIPS_R_T8, -20 - LLSC_offset);
+	emit(ctx, move, res, MIPS_R_T9);     /* Delay slot */
+	clobber_reg(ctx, res);
+}
+
+/* Swap bytes and truncate a register word or half word */
+void emit_bswap_r(struct jit_context *ctx, u8 dst, u32 width)
+{
+	u8 tmp = MIPS_R_T8;
+	u8 msk = MIPS_R_T9;
+
+	switch (width) {
+	/* Swap bytes in a word */
+	case 32:
+		if (cpu_has_mips32r2 || cpu_has_mips32r6) {
+			emit(ctx, wsbh, dst, dst);
+			emit(ctx, rotr, dst, dst, 16);
+		} else {
+			emit(ctx, sll, tmp, dst, 16);    /* tmp  = dst << 16 */
+			emit(ctx, srl, dst, dst, 16);    /* dst = dst >> 16  */
+			emit(ctx, or, dst, dst, tmp);    /* dst = dst | tmp  */
+
+			emit(ctx, lui, msk, 0xff);       /* msk = 0x00ff0000 */
+			emit(ctx, ori, msk, msk, 0xff);  /* msk = msk | 0xff */
+
+			emit(ctx, and, tmp, dst, msk);   /* tmp = dst & msk  */
+			emit(ctx, sll, tmp, tmp, 8);     /* tmp = tmp << 8   */
+			emit(ctx, srl, dst, dst, 8);     /* dst = dst >> 8   */
+			emit(ctx, and, dst, dst, msk);   /* dst = dst & msk  */
+			emit(ctx, or, dst, dst, tmp);    /* reg = dst | tmp  */
+		}
+		break;
+	/* Swap bytes in a half word */
+	case 16:
+		if (cpu_has_mips32r2 || cpu_has_mips32r6) {
+			emit(ctx, wsbh, dst, dst);
+			emit(ctx, andi, dst, dst, 0xffff);
+		} else {
+			emit(ctx, andi, tmp, dst, 0xff00); /* t = d & 0xff00 */
+			emit(ctx, srl, tmp, tmp, 8);       /* t = t >> 8     */
+			emit(ctx, andi, dst, dst, 0x00ff); /* d = d & 0x00ff */
+			emit(ctx, sll, dst, dst, 8);       /* d = d << 8     */
+			emit(ctx, or,  dst, dst, tmp);     /* d = d | t      */
+		}
+		break;
+	}
+	clobber_reg(ctx, dst);
+}
+
+/* Validate jump immediate range */
+bool valid_jmp_i(u8 op, s32 imm)
+{
+	switch (op) {
+	case JIT_JNOP:
+		/* Immediate value not used */
+		return true;
+	case BPF_JEQ:
+	case BPF_JNE:
+		/* No immediate operation */
+		return false;
+	case BPF_JSET:
+	case JIT_JNSET:
+		/* imm must be 16 bits unsigned */
+		return imm >= 0 && imm <= 0xffff;
+	case BPF_JGE:
+	case BPF_JLT:
+	case BPF_JSGE:
+	case BPF_JSLT:
+		/* imm must be 16 bits */
+		return imm >= -0x8000 && imm <= 0x7fff;
+	case BPF_JGT:
+	case BPF_JLE:
+	case BPF_JSGT:
+	case BPF_JSLE:
+		/* imm + 1 must be 16 bits */
+		return imm >= -0x8001 && imm <= 0x7ffe;
+	}
+	return false;
+}
+
+/* Invert a conditional jump operation */
+static u8 invert_jmp(u8 op)
+{
+	switch (op) {
+	case BPF_JA: return JIT_JNOP;
+	case BPF_JEQ: return BPF_JNE;
+	case BPF_JNE: return BPF_JEQ;
+	case BPF_JSET: return JIT_JNSET;
+	case BPF_JGT: return BPF_JLE;
+	case BPF_JGE: return BPF_JLT;
+	case BPF_JLT: return BPF_JGE;
+	case BPF_JLE: return BPF_JGT;
+	case BPF_JSGT: return BPF_JSLE;
+	case BPF_JSGE: return BPF_JSLT;
+	case BPF_JSLT: return BPF_JSGE;
+	case BPF_JSLE: return BPF_JSGT;
+	}
+	return 0;
+}
+
+/* Prepare a PC-relative jump operation */
+static void setup_jmp(struct jit_context *ctx, u8 bpf_op,
+		      s16 bpf_off, u8 *jit_op, s32 *jit_off)
+{
+	u32 *descp = &ctx->descriptors[ctx->bpf_index];
+	int op = bpf_op;
+	int offset = 0;
+
+	/* Do not compute offsets on the first pass */
+	if (INDEX(*descp) == 0)
+		goto done;
+
+	/* Skip jumps never taken */
+	if (bpf_op == JIT_JNOP)
+		goto done;
+
+	/* Convert jumps always taken */
+	if (bpf_op == BPF_JA)
+		*descp |= JIT_DESC_CONVERT;
+
+	/*
+	 * Current ctx->jit_index points to the start of the branch preamble.
+	 * Since the preamble differs among different branch conditionals,
+	 * the current index cannot be used to compute the branch offset.
+	 * Instead, we use the offset table value for the next instruction,
+	 * which gives the index immediately after the branch delay slot.
+	 */
+	if (!CONVERTED(*descp)) {
+		int target = ctx->bpf_index + bpf_off + 1;
+		int origin = ctx->bpf_index + 1;
+
+		offset = (INDEX(ctx->descriptors[target]) -
+			  INDEX(ctx->descriptors[origin]) + 1) * sizeof(u32);
+	}
+
+	/*
+	 * The PC-relative branch offset field on MIPS is 18 bits signed,
+	 * so if the computed offset is larger than this we generate a an
+	 * absolute jump that we skip with an inverted conditional branch.
+	 */
+	if (CONVERTED(*descp) || offset < -0x20000 || offset > 0x1ffff) {
+		offset = 3 * sizeof(u32);
+		op = invert_jmp(bpf_op);
+		ctx->changes += !CONVERTED(*descp);
+		*descp |= JIT_DESC_CONVERT;
+	}
+
+done:
+	*jit_off = offset;
+	*jit_op = op;
+}
+
+/* Prepare a PC-relative jump operation with immediate conditional */
+void setup_jmp_i(struct jit_context *ctx, s32 imm, u8 width,
+		 u8 bpf_op, s16 bpf_off, u8 *jit_op, s32 *jit_off)
+{
+	bool always = false;
+	bool never = false;
+
+	switch (bpf_op) {
+	case BPF_JEQ:
+	case BPF_JNE:
+		break;
+	case BPF_JSET:
+	case BPF_JLT:
+		never = imm == 0;
+		break;
+	case BPF_JGE:
+		always = imm == 0;
+		break;
+	case BPF_JGT:
+		never = (u32)imm == U32_MAX;
+		break;
+	case BPF_JLE:
+		always = (u32)imm == U32_MAX;
+		break;
+	case BPF_JSGT:
+		never = imm == S32_MAX && width == 32;
+		break;
+	case BPF_JSGE:
+		always = imm == S32_MIN && width == 32;
+		break;
+	case BPF_JSLT:
+		never = imm == S32_MIN && width == 32;
+		break;
+	case BPF_JSLE:
+		always = imm == S32_MAX && width == 32;
+		break;
+	}
+
+	if (never)
+		bpf_op = JIT_JNOP;
+	if (always)
+		bpf_op = BPF_JA;
+	setup_jmp(ctx, bpf_op, bpf_off, jit_op, jit_off);
+}
+
+/* Prepare a PC-relative jump operation with register conditional */
+void setup_jmp_r(struct jit_context *ctx, bool same_reg,
+		 u8 bpf_op, s16 bpf_off, u8 *jit_op, s32 *jit_off)
+{
+	switch (bpf_op) {
+	case BPF_JSET:
+		break;
+	case BPF_JEQ:
+	case BPF_JGE:
+	case BPF_JLE:
+	case BPF_JSGE:
+	case BPF_JSLE:
+		if (same_reg)
+			bpf_op = BPF_JA;
+		break;
+	case BPF_JNE:
+	case BPF_JLT:
+	case BPF_JGT:
+	case BPF_JSGT:
+	case BPF_JSLT:
+		if (same_reg)
+			bpf_op = JIT_JNOP;
+		break;
+	}
+	setup_jmp(ctx, bpf_op, bpf_off, jit_op, jit_off);
+}
+
+/* Finish a PC-relative jump operation */
+int finish_jmp(struct jit_context *ctx, u8 jit_op, s16 bpf_off)
+{
+	/* Emit conditional branch delay slot */
+	if (jit_op != JIT_JNOP)
+		emit(ctx, nop);
+	/*
+	 * Emit an absolute long jump with delay slot,
+	 * if the PC-relative branch was converted.
+	 */
+	if (CONVERTED(ctx->descriptors[ctx->bpf_index])) {
+		int target = get_target(ctx, ctx->bpf_index + bpf_off + 1);
+
+		if (target < 0)
+			return -1;
+		emit(ctx, j, target);
+		emit(ctx, nop);
+	}
+	return 0;
+}
+
+/* Jump immediate (32-bit) */
+void emit_jmp_i(struct jit_context *ctx, u8 dst, s32 imm, s32 off, u8 op)
+{
+	switch (op) {
+	/* No-op, used internally for branch optimization */
+	case JIT_JNOP:
+		break;
+	/* PC += off if dst & imm */
+	case BPF_JSET:
+		emit(ctx, andi, MIPS_R_T9, dst, (u16)imm);
+		emit(ctx, bnez, MIPS_R_T9, off);
+		break;
+	/* PC += off if (dst & imm) == 0 (not in BPF, used for long jumps) */
+	case JIT_JNSET:
+		emit(ctx, andi, MIPS_R_T9, dst, (u16)imm);
+		emit(ctx, beqz, MIPS_R_T9, off);
+		break;
+	/* PC += off if dst > imm */
+	case BPF_JGT:
+		emit(ctx, sltiu, MIPS_R_T9, dst, imm + 1);
+		emit(ctx, beqz, MIPS_R_T9, off);
+		break;
+	/* PC += off if dst >= imm */
+	case BPF_JGE:
+		emit(ctx, sltiu, MIPS_R_T9, dst, imm);
+		emit(ctx, beqz, MIPS_R_T9, off);
+		break;
+	/* PC += off if dst < imm */
+	case BPF_JLT:
+		emit(ctx, sltiu, MIPS_R_T9, dst, imm);
+		emit(ctx, bnez, MIPS_R_T9, off);
+		break;
+	/* PC += off if dst <= imm */
+	case BPF_JLE:
+		emit(ctx, sltiu, MIPS_R_T9, dst, imm + 1);
+		emit(ctx, bnez, MIPS_R_T9, off);
+		break;
+	/* PC += off if dst > imm (signed) */
+	case BPF_JSGT:
+		emit(ctx, slti, MIPS_R_T9, dst, imm + 1);
+		emit(ctx, beqz, MIPS_R_T9, off);
+		break;
+	/* PC += off if dst >= imm (signed) */
+	case BPF_JSGE:
+		emit(ctx, slti, MIPS_R_T9, dst, imm);
+		emit(ctx, beqz, MIPS_R_T9, off);
+		break;
+	/* PC += off if dst < imm (signed) */
+	case BPF_JSLT:
+		emit(ctx, slti, MIPS_R_T9, dst, imm);
+		emit(ctx, bnez, MIPS_R_T9, off);
+		break;
+	/* PC += off if dst <= imm (signed) */
+	case BPF_JSLE:
+		emit(ctx, slti, MIPS_R_T9, dst, imm + 1);
+		emit(ctx, bnez, MIPS_R_T9, off);
+		break;
+	}
+}
+
+/* Jump register (32-bit) */
+void emit_jmp_r(struct jit_context *ctx, u8 dst, u8 src, s32 off, u8 op)
+{
+	switch (op) {
+	/* No-op, used internally for branch optimization */
+	case JIT_JNOP:
+		break;
+	/* PC += off if dst == src */
+	case BPF_JEQ:
+		emit(ctx, beq, dst, src, off);
+		break;
+	/* PC += off if dst != src */
+	case BPF_JNE:
+		emit(ctx, bne, dst, src, off);
+		break;
+	/* PC += off if dst & src */
+	case BPF_JSET:
+		emit(ctx, and, MIPS_R_T9, dst, src);
+		emit(ctx, bnez, MIPS_R_T9, off);
+		break;
+	/* PC += off if (dst & imm) == 0 (not in BPF, used for long jumps) */
+	case JIT_JNSET:
+		emit(ctx, and, MIPS_R_T9, dst, src);
+		emit(ctx, beqz, MIPS_R_T9, off);
+		break;
+	/* PC += off if dst > src */
+	case BPF_JGT:
+		emit(ctx, sltu, MIPS_R_T9, src, dst);
+		emit(ctx, bnez, MIPS_R_T9, off);
+		break;
+	/* PC += off if dst >= src */
+	case BPF_JGE:
+		emit(ctx, sltu, MIPS_R_T9, dst, src);
+		emit(ctx, beqz, MIPS_R_T9, off);
+		break;
+	/* PC += off if dst < src */
+	case BPF_JLT:
+		emit(ctx, sltu, MIPS_R_T9, dst, src);
+		emit(ctx, bnez, MIPS_R_T9, off);
+		break;
+	/* PC += off if dst <= src */
+	case BPF_JLE:
+		emit(ctx, sltu, MIPS_R_T9, src, dst);
+		emit(ctx, beqz, MIPS_R_T9, off);
+		break;
+	/* PC += off if dst > src (signed) */
+	case BPF_JSGT:
+		emit(ctx, slt, MIPS_R_T9, src, dst);
+		emit(ctx, bnez, MIPS_R_T9, off);
+		break;
+	/* PC += off if dst >= src (signed) */
+	case BPF_JSGE:
+		emit(ctx, slt, MIPS_R_T9, dst, src);
+		emit(ctx, beqz, MIPS_R_T9, off);
+		break;
+	/* PC += off if dst < src (signed) */
+	case BPF_JSLT:
+		emit(ctx, slt, MIPS_R_T9, dst, src);
+		emit(ctx, bnez, MIPS_R_T9, off);
+		break;
+	/* PC += off if dst <= src (signed) */
+	case BPF_JSLE:
+		emit(ctx, slt, MIPS_R_T9, src, dst);
+		emit(ctx, beqz, MIPS_R_T9, off);
+		break;
+	}
+}
+
+/* Jump always */
+int emit_ja(struct jit_context *ctx, s16 off)
+{
+	int target = get_target(ctx, ctx->bpf_index + off + 1);
+
+	if (target < 0)
+		return -1;
+	emit(ctx, j, target);
+	emit(ctx, nop);
+	return 0;
+}
+
+/* Jump to epilogue */
+int emit_exit(struct jit_context *ctx)
+{
+	int target = get_target(ctx, ctx->program->len);
+
+	if (target < 0)
+		return -1;
+	emit(ctx, j, target);
+	emit(ctx, nop);
+	return 0;
+}
+
+/* Build the program body from eBPF bytecode */
+static int build_body(struct jit_context *ctx)
+{
+	const struct bpf_prog *prog = ctx->program;
+	unsigned int i;
+
+	ctx->stack_used = 0;
+	for (i = 0; i < prog->len; i++) {
+		const struct bpf_insn *insn = &prog->insnsi[i];
+		u32 *descp = &ctx->descriptors[i];
+		int ret;
+
+		access_reg(ctx, insn->src_reg);
+		access_reg(ctx, insn->dst_reg);
+
+		ctx->bpf_index = i;
+		if (ctx->target == NULL) {
+			ctx->changes += INDEX(*descp) != ctx->jit_index;
+			*descp &= JIT_DESC_CONVERT;
+			*descp |= ctx->jit_index;
+		}
+
+		ret = build_insn(insn, ctx);
+		if (ret < 0)
+			return ret;
+
+		if (ret > 0) {
+			i++;
+			if (ctx->target == NULL)
+				descp[1] = ctx->jit_index;
+		}
+	}
+
+	/* Store the end offset, where the epilogue begins */
+	ctx->descriptors[prog->len] = ctx->jit_index;
+	return 0;
+}
+
+/* Set the branch conversion flag on all instructions */
+static void set_convert_flag(struct jit_context *ctx, bool enable)
+{
+	const struct bpf_prog *prog = ctx->program;
+	u32 flag = enable ? JIT_DESC_CONVERT : 0;
+	unsigned int i;
+
+	for (i = 0; i <= prog->len; i++)
+		ctx->descriptors[i] = INDEX(ctx->descriptors[i]) | flag;
+}
+
+static void jit_fill_hole(void *area, unsigned int size)
+{
+	u32 *p;
+
+	/* We are guaranteed to have aligned memory. */
+	for (p = area; size >= sizeof(u32); size -= sizeof(u32))
+		uasm_i_break(&p, BRK_BUG); /* Increments p */
+}
+
+bool bpf_jit_needs_zext(void)
+{
+	return true;
+}
+
+struct bpf_prog *bpf_int_jit_compile(struct bpf_prog *prog)
+{
+	struct bpf_prog *tmp, *orig_prog = prog;
+	struct bpf_binary_header *header = NULL;
+	struct jit_context ctx;
+	bool tmp_blinded = false;
+	unsigned int tmp_idx;
+	unsigned int image_size;
+	u8 *image_ptr;
+	int tries;
+
+	/*
+	 * If BPF JIT was not enabled then we must fall back to
+	 * the interpreter.
+	 */
+	if (!prog->jit_requested)
+		return orig_prog;
+	/*
+	 * If constant blinding was enabled and we failed during blinding
+	 * then we must fall back to the interpreter. Otherwise, we save
+	 * the new JITed code.
+	 */
+	tmp = bpf_jit_blind_constants(prog);
+	if (IS_ERR(tmp))
+		return orig_prog;
+	if (tmp != prog) {
+		tmp_blinded = true;
+		prog = tmp;
+	}
+
+	memset(&ctx, 0, sizeof(ctx));
+	ctx.program = prog;
+
+	/*
+	 * Not able to allocate memory for descriptors[], then
+	 * we must fall back to the interpreter
+	 */
+	ctx.descriptors = kcalloc(prog->len + 1, sizeof(*ctx.descriptors),
+				  GFP_KERNEL);
+	if (ctx.descriptors == NULL)
+		goto out_err;
+
+	/* First pass discovers used resources */
+	if (build_body(&ctx) < 0)
+		goto out_err;
+	/*
+	 * Second pass computes instruction offsets.
+	 * If any PC-relative branches are out of range, a sequence of
+	 * a PC-relative branch + a jump is generated, and we have to
+	 * try again from the beginning to generate the new offsets.
+	 * This is done until no additional conversions are necessary.
+	 * The last two iterations are done with all branches being
+	 * converted, to guarantee offset table convergence within a
+	 * fixed number of iterations.
+	 */
+	ctx.jit_index = 0;
+	build_prologue(&ctx);
+	tmp_idx = ctx.jit_index;
+
+	tries = JIT_MAX_ITERATIONS;
+	do {
+		ctx.jit_index = tmp_idx;
+		ctx.changes = 0;
+		if (tries == 2)
+			set_convert_flag(&ctx, true);
+		if (build_body(&ctx) < 0)
+			goto out_err;
+	} while (ctx.changes > 0 && --tries > 0);
+
+	if (WARN_ONCE(ctx.changes > 0, "JIT offsets failed to converge"))
+		goto out_err;
+
+	build_epilogue(&ctx, MIPS_R_RA);
+
+	/* Now we know the size of the structure to make */
+	image_size = sizeof(u32) * ctx.jit_index;
+	header = bpf_jit_binary_alloc(image_size, &image_ptr,
+				      sizeof(u32), jit_fill_hole);
+	/*
+	 * Not able to allocate memory for the structure then
+	 * we must fall back to the interpretation
+	 */
+	if (header == NULL)
+		goto out_err;
+
+	/* Actual pass to generate final JIT code */
+	ctx.target = (u32 *)image_ptr;
+	ctx.jit_index = 0;
+
+	/*
+	 * If building the JITed code fails somehow,
+	 * we fall back to the interpretation.
+	 */
+	build_prologue(&ctx);
+	if (build_body(&ctx) < 0)
+		goto out_err;
+	build_epilogue(&ctx, MIPS_R_RA);
+
+	/* Populate line info meta data */
+	set_convert_flag(&ctx, false);
+	bpf_prog_fill_jited_linfo(prog, &ctx.descriptors[1]);
+
+	/* Set as read-only exec and flush instruction cache */
+	bpf_jit_binary_lock_ro(header);
+	flush_icache_range((unsigned long)header,
+			   (unsigned long)&ctx.target[ctx.jit_index]);
+
+	if (bpf_jit_enable > 1)
+		bpf_jit_dump(prog->len, image_size, 2, ctx.target);
+
+	prog->bpf_func = (void *)ctx.target;
+	prog->jited = 1;
+	prog->jited_len = image_size;
+
+out:
+	if (tmp_blinded)
+		bpf_jit_prog_release_other(prog, prog == orig_prog ?
+					   tmp : orig_prog);
+	kfree(ctx.descriptors);
+	return prog;
+
+out_err:
+	prog = orig_prog;
+	if (header)
+		bpf_jit_binary_free(header);
+	goto out;
+}
diff --git a/arch/mips/net/bpf_jit_comp.h b/arch/mips/net/bpf_jit_comp.h
new file mode 100644
index 000000000..a37fe2081
--- /dev/null
+++ b/arch/mips/net/bpf_jit_comp.h
@@ -0,0 +1,235 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Just-In-Time compiler for eBPF bytecode on 32-bit and 64-bit MIPS.
+ *
+ * Copyright (c) 2021 Anyfi Networks AB.
+ * Author: Johan Almbladh <johan.almbladh@gmail.com>
+ *
+ * Based on code and ideas from
+ * Copyright (c) 2017 Cavium, Inc.
+ * Copyright (c) 2017 Shubham Bansal <illusionist.neo@gmail.com>
+ * Copyright (c) 2011 Mircea Gherzan <mgherzan@gmail.com>
+ */
+
+#ifndef _BPF_JIT_COMP_H
+#define _BPF_JIT_COMP_H
+
+/* MIPS registers */
+#define MIPS_R_ZERO	0   /* Const zero */
+#define MIPS_R_AT	1   /* Asm temp   */
+#define MIPS_R_V0	2   /* Result     */
+#define MIPS_R_V1	3   /* Result     */
+#define MIPS_R_A0	4   /* Argument   */
+#define MIPS_R_A1	5   /* Argument   */
+#define MIPS_R_A2	6   /* Argument   */
+#define MIPS_R_A3	7   /* Argument   */
+#define MIPS_R_A4	8   /* Arg (n64)  */
+#define MIPS_R_A5	9   /* Arg (n64)  */
+#define MIPS_R_A6	10  /* Arg (n64)  */
+#define MIPS_R_A7	11  /* Arg (n64)  */
+#define MIPS_R_T0	8   /* Temp (o32) */
+#define MIPS_R_T1	9   /* Temp (o32) */
+#define MIPS_R_T2	10  /* Temp (o32) */
+#define MIPS_R_T3	11  /* Temp (o32) */
+#define MIPS_R_T4	12  /* Temporary  */
+#define MIPS_R_T5	13  /* Temporary  */
+#define MIPS_R_T6	14  /* Temporary  */
+#define MIPS_R_T7	15  /* Temporary  */
+#define MIPS_R_S0	16  /* Saved      */
+#define MIPS_R_S1	17  /* Saved      */
+#define MIPS_R_S2	18  /* Saved      */
+#define MIPS_R_S3	19  /* Saved      */
+#define MIPS_R_S4	20  /* Saved      */
+#define MIPS_R_S5	21  /* Saved      */
+#define MIPS_R_S6	22  /* Saved      */
+#define MIPS_R_S7	23  /* Saved      */
+#define MIPS_R_T8	24  /* Temporary  */
+#define MIPS_R_T9	25  /* Temporary  */
+/*      MIPS_R_K0	26     Reserved   */
+/*      MIPS_R_K1	27     Reserved   */
+#define MIPS_R_GP	28  /* Global ptr */
+#define MIPS_R_SP	29  /* Stack ptr  */
+#define MIPS_R_FP	30  /* Frame ptr  */
+#define MIPS_R_RA	31  /* Return     */
+
+/*
+ * Jump address mask for immediate jumps. The four most significant bits
+ * must be equal to PC.
+ */
+#define MIPS_JMP_MASK	0x0fffffffUL
+
+/* Maximum number of iterations in offset table computation */
+#define JIT_MAX_ITERATIONS	8
+
+/*
+ * Jump pseudo-instructions used internally
+ * for branch conversion and branch optimization.
+ */
+#define JIT_JNSET	0xe0
+#define JIT_JNOP	0xf0
+
+/* Descriptor flag for PC-relative branch conversion */
+#define JIT_DESC_CONVERT	BIT(31)
+
+/* JIT context for an eBPF program */
+struct jit_context {
+	struct bpf_prog *program;     /* The eBPF program being JITed        */
+	u32 *descriptors;             /* eBPF to JITed CPU insn descriptors  */
+	u32 *target;                  /* JITed code buffer                   */
+	u32 bpf_index;                /* Index of current BPF program insn   */
+	u32 jit_index;                /* Index of current JIT target insn    */
+	u32 changes;                  /* Number of PC-relative branch conv   */
+	u32 accessed;                 /* Bit mask of read eBPF registers     */
+	u32 clobbered;                /* Bit mask of modified CPU registers  */
+	u32 stack_size;               /* Total allocated stack size in bytes */
+	u32 saved_size;               /* Size of callee-saved registers      */
+	u32 stack_used;               /* Stack size used for function calls  */
+};
+
+/* Emit the instruction if the JIT memory space has been allocated */
+#define __emit(ctx, func, ...)					\
+do {								\
+	if ((ctx)->target != NULL) {				\
+		u32 *p = &(ctx)->target[ctx->jit_index];	\
+		uasm_i_##func(&p, ##__VA_ARGS__);		\
+	}							\
+	(ctx)->jit_index++;					\
+} while (0)
+#define emit(...) __emit(__VA_ARGS__)
+
+/* Workaround for R10000 ll/sc errata */
+#ifdef CONFIG_WAR_R10000_LLSC
+#define LLSC_beqz	beqzl
+#else
+#define LLSC_beqz	beqz
+#endif
+
+/* Workaround for Loongson-3 ll/sc errata */
+#ifdef CONFIG_CPU_LOONGSON3_WORKAROUNDS
+#define LLSC_sync(ctx)	emit(ctx, sync, 0)
+#define LLSC_offset	4
+#else
+#define LLSC_sync(ctx)
+#define LLSC_offset	0
+#endif
+
+/* Workaround for Loongson-2F jump errata */
+#ifdef CONFIG_CPU_JUMP_WORKAROUNDS
+#define JALR_MASK	0xffffffffcfffffffULL
+#else
+#define JALR_MASK	(~0ULL)
+#endif
+
+/*
+ * Mark a BPF register as accessed, it needs to be
+ * initialized by the program if expected, e.g. FP.
+ */
+static inline void access_reg(struct jit_context *ctx, u8 reg)
+{
+	ctx->accessed |= BIT(reg);
+}
+
+/*
+ * Mark a CPU register as clobbered, it needs to be
+ * saved/restored by the program if callee-saved.
+ */
+static inline void clobber_reg(struct jit_context *ctx, u8 reg)
+{
+	ctx->clobbered |= BIT(reg);
+}
+
+/*
+ * Push registers on the stack, starting at a given depth from the stack
+ * pointer and increasing. The next depth to be written is returned.
+ */
+int push_regs(struct jit_context *ctx, u32 mask, u32 excl, int depth);
+
+/*
+ * Pop registers from the stack, starting at a given depth from the stack
+ * pointer and increasing. The next depth to be read is returned.
+ */
+int pop_regs(struct jit_context *ctx, u32 mask, u32 excl, int depth);
+
+/* Compute the 28-bit jump target address from a BPF program location */
+int get_target(struct jit_context *ctx, u32 loc);
+
+/* Compute the PC-relative offset to relative BPF program offset */
+int get_offset(const struct jit_context *ctx, int off);
+
+/* dst = imm (32-bit) */
+void emit_mov_i(struct jit_context *ctx, u8 dst, s32 imm);
+
+/* dst = src (32-bit) */
+void emit_mov_r(struct jit_context *ctx, u8 dst, u8 src);
+
+/* Validate ALU/ALU64 immediate range */
+bool valid_alu_i(u8 op, s32 imm);
+
+/* Rewrite ALU/ALU64 immediate operation */
+bool rewrite_alu_i(u8 op, s32 imm, u8 *alu, s32 *val);
+
+/* ALU immediate operation (32-bit) */
+void emit_alu_i(struct jit_context *ctx, u8 dst, s32 imm, u8 op);
+
+/* ALU register operation (32-bit) */
+void emit_alu_r(struct jit_context *ctx, u8 dst, u8 src, u8 op);
+
+/* Atomic read-modify-write (32-bit) */
+void emit_atomic_r(struct jit_context *ctx, u8 dst, u8 src, s16 off, u8 code);
+
+/* Atomic compare-and-exchange (32-bit) */
+void emit_cmpxchg_r(struct jit_context *ctx, u8 dst, u8 src, u8 res, s16 off);
+
+/* Swap bytes and truncate a register word or half word */
+void emit_bswap_r(struct jit_context *ctx, u8 dst, u32 width);
+
+/* Validate JMP/JMP32 immediate range */
+bool valid_jmp_i(u8 op, s32 imm);
+
+/* Prepare a PC-relative jump operation with immediate conditional */
+void setup_jmp_i(struct jit_context *ctx, s32 imm, u8 width,
+		 u8 bpf_op, s16 bpf_off, u8 *jit_op, s32 *jit_off);
+
+/* Prepare a PC-relative jump operation with register conditional */
+void setup_jmp_r(struct jit_context *ctx, bool same_reg,
+		 u8 bpf_op, s16 bpf_off, u8 *jit_op, s32 *jit_off);
+
+/* Finish a PC-relative jump operation */
+int finish_jmp(struct jit_context *ctx, u8 jit_op, s16 bpf_off);
+
+/* Conditional JMP/JMP32 immediate */
+void emit_jmp_i(struct jit_context *ctx, u8 dst, s32 imm, s32 off, u8 op);
+
+/* Conditional JMP/JMP32 register */
+void emit_jmp_r(struct jit_context *ctx, u8 dst, u8 src, s32 off, u8 op);
+
+/* Jump always */
+int emit_ja(struct jit_context *ctx, s16 off);
+
+/* Jump to epilogue */
+int emit_exit(struct jit_context *ctx);
+
+/*
+ * Build program prologue to set up the stack and registers.
+ * This function is implemented separately for 32-bit and 64-bit JITs.
+ */
+void build_prologue(struct jit_context *ctx);
+
+/*
+ * Build the program epilogue to restore the stack and registers.
+ * This function is implemented separately for 32-bit and 64-bit JITs.
+ */
+void build_epilogue(struct jit_context *ctx, int dest_reg);
+
+/*
+ * Convert an eBPF instruction to native instruction, i.e
+ * JITs an eBPF instruction.
+ * Returns :
+ *	0  - Successfully JITed an 8-byte eBPF instruction
+ *	>0 - Successfully JITed a 16-byte eBPF instruction
+ *	<0 - Failed to JIT.
+ * This function is implemented separately for 32-bit and 64-bit JITs.
+ */
+int build_insn(const struct bpf_insn *insn, struct jit_context *ctx);
+
+#endif /* _BPF_JIT_COMP_H */
diff --git a/arch/mips/net/bpf_jit_comp32.c b/arch/mips/net/bpf_jit_comp32.c
new file mode 100644
index 000000000..ace5db3fb
--- /dev/null
+++ b/arch/mips/net/bpf_jit_comp32.c
@@ -0,0 +1,1906 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Just-In-Time compiler for eBPF bytecode on MIPS.
+ * Implementation of JIT functions for 32-bit CPUs.
+ *
+ * Copyright (c) 2021 Anyfi Networks AB.
+ * Author: Johan Almbladh <johan.almbladh@gmail.com>
+ *
+ * Based on code and ideas from
+ * Copyright (c) 2017 Cavium, Inc.
+ * Copyright (c) 2017 Shubham Bansal <illusionist.neo@gmail.com>
+ * Copyright (c) 2011 Mircea Gherzan <mgherzan@gmail.com>
+ */
+
+#include <linux/math64.h>
+#include <linux/errno.h>
+#include <linux/filter.h>
+#include <linux/bpf.h>
+#include <asm/cpu-features.h>
+#include <asm/isa-rev.h>
+#include <asm/uasm.h>
+
+#include "bpf_jit_comp.h"
+
+/* MIPS a4-a7 are not available in the o32 ABI */
+#undef MIPS_R_A4
+#undef MIPS_R_A5
+#undef MIPS_R_A6
+#undef MIPS_R_A7
+
+/* Stack is 8-byte aligned in o32 ABI */
+#define MIPS_STACK_ALIGNMENT 8
+
+/*
+ * The top 16 bytes of a stack frame is reserved for the callee in O32 ABI.
+ * This corresponds to stack space for register arguments a0-a3.
+ */
+#define JIT_RESERVED_STACK 16
+
+/* Temporary 64-bit register used by JIT */
+#define JIT_REG_TMP MAX_BPF_JIT_REG
+
+/*
+ * Number of prologue bytes to skip when doing a tail call.
+ * Tail call count (TCC) initialization (8 bytes) always, plus
+ * R0-to-v0 assignment (4 bytes) if big endian.
+ */
+#ifdef __BIG_ENDIAN
+#define JIT_TCALL_SKIP 12
+#else
+#define JIT_TCALL_SKIP 8
+#endif
+
+/* CPU registers holding the callee return value */
+#define JIT_RETURN_REGS	  \
+	(BIT(MIPS_R_V0) | \
+	 BIT(MIPS_R_V1))
+
+/* CPU registers arguments passed to callee directly */
+#define JIT_ARG_REGS      \
+	(BIT(MIPS_R_A0) | \
+	 BIT(MIPS_R_A1) | \
+	 BIT(MIPS_R_A2) | \
+	 BIT(MIPS_R_A3))
+
+/* CPU register arguments passed to callee on stack */
+#define JIT_STACK_REGS    \
+	(BIT(MIPS_R_T0) | \
+	 BIT(MIPS_R_T1) | \
+	 BIT(MIPS_R_T2) | \
+	 BIT(MIPS_R_T3) | \
+	 BIT(MIPS_R_T4) | \
+	 BIT(MIPS_R_T5))
+
+/* Caller-saved CPU registers */
+#define JIT_CALLER_REGS    \
+	(JIT_RETURN_REGS | \
+	 JIT_ARG_REGS    | \
+	 JIT_STACK_REGS)
+
+/* Callee-saved CPU registers */
+#define JIT_CALLEE_REGS   \
+	(BIT(MIPS_R_S0) | \
+	 BIT(MIPS_R_S1) | \
+	 BIT(MIPS_R_S2) | \
+	 BIT(MIPS_R_S3) | \
+	 BIT(MIPS_R_S4) | \
+	 BIT(MIPS_R_S5) | \
+	 BIT(MIPS_R_S6) | \
+	 BIT(MIPS_R_S7) | \
+	 BIT(MIPS_R_GP) | \
+	 BIT(MIPS_R_FP) | \
+	 BIT(MIPS_R_RA))
+
+/*
+ * Mapping of 64-bit eBPF registers to 32-bit native MIPS registers.
+ *
+ * 1) Native register pairs are ordered according to CPU endiannes, following
+ *    the MIPS convention for passing 64-bit arguments and return values.
+ * 2) The eBPF return value, arguments and callee-saved registers are mapped
+ *    to their native MIPS equivalents.
+ * 3) Since the 32 highest bits in the eBPF FP register are always zero,
+ *    only one general-purpose register is actually needed for the mapping.
+ *    We use the fp register for this purpose, and map the highest bits to
+ *    the MIPS register r0 (zero).
+ * 4) We use the MIPS gp and at registers as internal temporary registers
+ *    for constant blinding. The gp register is callee-saved.
+ * 5) One 64-bit temporary register is mapped for use when sign-extending
+ *    immediate operands. MIPS registers t6-t9 are available to the JIT
+ *    for as temporaries when implementing complex 64-bit operations.
+ *
+ * With this scheme all eBPF registers are being mapped to native MIPS
+ * registers without having to use any stack scratch space. The direct
+ * register mapping (2) simplifies the handling of function calls.
+ */
+static const u8 bpf2mips32[][2] = {
+	/* Return value from in-kernel function, and exit value from eBPF */
+	[BPF_REG_0] = {MIPS_R_V1, MIPS_R_V0},
+	/* Arguments from eBPF program to in-kernel function */
+	[BPF_REG_1] = {MIPS_R_A1, MIPS_R_A0},
+	[BPF_REG_2] = {MIPS_R_A3, MIPS_R_A2},
+	/* Remaining arguments, to be passed on the stack per O32 ABI */
+	[BPF_REG_3] = {MIPS_R_T1, MIPS_R_T0},
+	[BPF_REG_4] = {MIPS_R_T3, MIPS_R_T2},
+	[BPF_REG_5] = {MIPS_R_T5, MIPS_R_T4},
+	/* Callee-saved registers that in-kernel function will preserve */
+	[BPF_REG_6] = {MIPS_R_S1, MIPS_R_S0},
+	[BPF_REG_7] = {MIPS_R_S3, MIPS_R_S2},
+	[BPF_REG_8] = {MIPS_R_S5, MIPS_R_S4},
+	[BPF_REG_9] = {MIPS_R_S7, MIPS_R_S6},
+	/* Read-only frame pointer to access the eBPF stack */
+#ifdef __BIG_ENDIAN
+	[BPF_REG_FP] = {MIPS_R_FP, MIPS_R_ZERO},
+#else
+	[BPF_REG_FP] = {MIPS_R_ZERO, MIPS_R_FP},
+#endif
+	/* Temporary register for blinding constants */
+	[BPF_REG_AX] = {MIPS_R_GP, MIPS_R_AT},
+	/* Temporary register for internal JIT use */
+	[JIT_REG_TMP] = {MIPS_R_T7, MIPS_R_T6},
+};
+
+/* Get low CPU register for a 64-bit eBPF register mapping */
+static inline u8 lo(const u8 reg[])
+{
+#ifdef __BIG_ENDIAN
+	return reg[0];
+#else
+	return reg[1];
+#endif
+}
+
+/* Get high CPU register for a 64-bit eBPF register mapping */
+static inline u8 hi(const u8 reg[])
+{
+#ifdef __BIG_ENDIAN
+	return reg[1];
+#else
+	return reg[0];
+#endif
+}
+
+/*
+ * Mark a 64-bit CPU register pair as clobbered, it needs to be
+ * saved/restored by the program if callee-saved.
+ */
+static void clobber_reg64(struct jit_context *ctx, const u8 reg[])
+{
+	clobber_reg(ctx, reg[0]);
+	clobber_reg(ctx, reg[1]);
+}
+
+/* dst = imm (sign-extended) */
+static void emit_mov_se_i64(struct jit_context *ctx, const u8 dst[], s32 imm)
+{
+	emit_mov_i(ctx, lo(dst), imm);
+	if (imm < 0)
+		emit(ctx, addiu, hi(dst), MIPS_R_ZERO, -1);
+	else
+		emit(ctx, move, hi(dst), MIPS_R_ZERO);
+	clobber_reg64(ctx, dst);
+}
+
+/* Zero extension, if verifier does not do it for us  */
+static void emit_zext_ver(struct jit_context *ctx, const u8 dst[])
+{
+	if (!ctx->program->aux->verifier_zext) {
+		emit(ctx, move, hi(dst), MIPS_R_ZERO);
+		clobber_reg(ctx, hi(dst));
+	}
+}
+
+/* Load delay slot, if ISA mandates it */
+static void emit_load_delay(struct jit_context *ctx)
+{
+	if (!cpu_has_mips_2_3_4_5_r)
+		emit(ctx, nop);
+}
+
+/* ALU immediate operation (64-bit) */
+static void emit_alu_i64(struct jit_context *ctx,
+			 const u8 dst[], s32 imm, u8 op)
+{
+	u8 src = MIPS_R_T6;
+
+	/*
+	 * ADD/SUB with all but the max negative imm can be handled by
+	 * inverting the operation and the imm value, saving one insn.
+	 */
+	if (imm > S32_MIN && imm < 0)
+		switch (op) {
+		case BPF_ADD:
+			op = BPF_SUB;
+			imm = -imm;
+			break;
+		case BPF_SUB:
+			op = BPF_ADD;
+			imm = -imm;
+			break;
+		}
+
+	/* Move immediate to temporary register */
+	emit_mov_i(ctx, src, imm);
+
+	switch (op) {
+	/* dst = dst + imm */
+	case BPF_ADD:
+		emit(ctx, addu, lo(dst), lo(dst), src);
+		emit(ctx, sltu, MIPS_R_T9, lo(dst), src);
+		emit(ctx, addu, hi(dst), hi(dst), MIPS_R_T9);
+		if (imm < 0)
+			emit(ctx, addiu, hi(dst), hi(dst), -1);
+		break;
+	/* dst = dst - imm */
+	case BPF_SUB:
+		emit(ctx, sltu, MIPS_R_T9, lo(dst), src);
+		emit(ctx, subu, lo(dst), lo(dst), src);
+		emit(ctx, subu, hi(dst), hi(dst), MIPS_R_T9);
+		if (imm < 0)
+			emit(ctx, addiu, hi(dst), hi(dst), 1);
+		break;
+	/* dst = dst | imm */
+	case BPF_OR:
+		emit(ctx, or, lo(dst), lo(dst), src);
+		if (imm < 0)
+			emit(ctx, addiu, hi(dst), MIPS_R_ZERO, -1);
+		break;
+	/* dst = dst & imm */
+	case BPF_AND:
+		emit(ctx, and, lo(dst), lo(dst), src);
+		if (imm >= 0)
+			emit(ctx, move, hi(dst), MIPS_R_ZERO);
+		break;
+	/* dst = dst ^ imm */
+	case BPF_XOR:
+		emit(ctx, xor, lo(dst), lo(dst), src);
+		if (imm < 0) {
+			emit(ctx, subu, hi(dst), MIPS_R_ZERO, hi(dst));
+			emit(ctx, addiu, hi(dst), hi(dst), -1);
+		}
+		break;
+	}
+	clobber_reg64(ctx, dst);
+}
+
+/* ALU register operation (64-bit) */
+static void emit_alu_r64(struct jit_context *ctx,
+			 const u8 dst[], const u8 src[], u8 op)
+{
+	switch (BPF_OP(op)) {
+	/* dst = dst + src */
+	case BPF_ADD:
+		if (src == dst) {
+			emit(ctx, srl, MIPS_R_T9, lo(dst), 31);
+			emit(ctx, addu, lo(dst), lo(dst), lo(dst));
+		} else {
+			emit(ctx, addu, lo(dst), lo(dst), lo(src));
+			emit(ctx, sltu, MIPS_R_T9, lo(dst), lo(src));
+		}
+		emit(ctx, addu, hi(dst), hi(dst), hi(src));
+		emit(ctx, addu, hi(dst), hi(dst), MIPS_R_T9);
+		break;
+	/* dst = dst - src */
+	case BPF_SUB:
+		emit(ctx, sltu, MIPS_R_T9, lo(dst), lo(src));
+		emit(ctx, subu, lo(dst), lo(dst), lo(src));
+		emit(ctx, subu, hi(dst), hi(dst), hi(src));
+		emit(ctx, subu, hi(dst), hi(dst), MIPS_R_T9);
+		break;
+	/* dst = dst | src */
+	case BPF_OR:
+		emit(ctx, or, lo(dst), lo(dst), lo(src));
+		emit(ctx, or, hi(dst), hi(dst), hi(src));
+		break;
+	/* dst = dst & src */
+	case BPF_AND:
+		emit(ctx, and, lo(dst), lo(dst), lo(src));
+		emit(ctx, and, hi(dst), hi(dst), hi(src));
+		break;
+	/* dst = dst ^ src */
+	case BPF_XOR:
+		emit(ctx, xor, lo(dst), lo(dst), lo(src));
+		emit(ctx, xor, hi(dst), hi(dst), hi(src));
+		break;
+	}
+	clobber_reg64(ctx, dst);
+}
+
+/* ALU invert (64-bit) */
+static void emit_neg_i64(struct jit_context *ctx, const u8 dst[])
+{
+	emit(ctx, sltu, MIPS_R_T9, MIPS_R_ZERO, lo(dst));
+	emit(ctx, subu, lo(dst), MIPS_R_ZERO, lo(dst));
+	emit(ctx, subu, hi(dst), MIPS_R_ZERO, hi(dst));
+	emit(ctx, subu, hi(dst), hi(dst), MIPS_R_T9);
+
+	clobber_reg64(ctx, dst);
+}
+
+/* ALU shift immediate (64-bit) */
+static void emit_shift_i64(struct jit_context *ctx,
+			   const u8 dst[], u32 imm, u8 op)
+{
+	switch (BPF_OP(op)) {
+	/* dst = dst << imm */
+	case BPF_LSH:
+		if (imm < 32) {
+			emit(ctx, srl, MIPS_R_T9, lo(dst), 32 - imm);
+			emit(ctx, sll, lo(dst), lo(dst), imm);
+			emit(ctx, sll, hi(dst), hi(dst), imm);
+			emit(ctx, or, hi(dst), hi(dst), MIPS_R_T9);
+		} else {
+			emit(ctx, sll, hi(dst), lo(dst), imm - 32);
+			emit(ctx, move, lo(dst), MIPS_R_ZERO);
+		}
+		break;
+	/* dst = dst >> imm */
+	case BPF_RSH:
+		if (imm < 32) {
+			emit(ctx, sll, MIPS_R_T9, hi(dst), 32 - imm);
+			emit(ctx, srl, lo(dst), lo(dst), imm);
+			emit(ctx, srl, hi(dst), hi(dst), imm);
+			emit(ctx, or, lo(dst), lo(dst), MIPS_R_T9);
+		} else {
+			emit(ctx, srl, lo(dst), hi(dst), imm - 32);
+			emit(ctx, move, hi(dst), MIPS_R_ZERO);
+		}
+		break;
+	/* dst = dst >> imm (arithmetic) */
+	case BPF_ARSH:
+		if (imm < 32) {
+			emit(ctx, sll, MIPS_R_T9, hi(dst), 32 - imm);
+			emit(ctx, srl, lo(dst), lo(dst), imm);
+			emit(ctx, sra, hi(dst), hi(dst), imm);
+			emit(ctx, or, lo(dst), lo(dst), MIPS_R_T9);
+		} else {
+			emit(ctx, sra, lo(dst), hi(dst), imm - 32);
+			emit(ctx, sra, hi(dst), hi(dst), 31);
+		}
+		break;
+	}
+	clobber_reg64(ctx, dst);
+}
+
+/* ALU shift register (64-bit) */
+static void emit_shift_r64(struct jit_context *ctx,
+			   const u8 dst[], u8 src, u8 op)
+{
+	u8 t1 = MIPS_R_T8;
+	u8 t2 = MIPS_R_T9;
+
+	emit(ctx, andi, t1, src, 32);              /* t1 = src & 32          */
+	emit(ctx, beqz, t1, 16);                   /* PC += 16 if t1 == 0    */
+	emit(ctx, nor, t2, src, MIPS_R_ZERO);      /* t2 = ~src (delay slot) */
+
+	switch (BPF_OP(op)) {
+	/* dst = dst << src */
+	case BPF_LSH:
+		/* Next: shift >= 32 */
+		emit(ctx, sllv, hi(dst), lo(dst), src);    /* dh = dl << src */
+		emit(ctx, move, lo(dst), MIPS_R_ZERO);     /* dl = 0         */
+		emit(ctx, b, 20);                          /* PC += 20       */
+		/* +16: shift < 32 */
+		emit(ctx, srl, t1, lo(dst), 1);            /* t1 = dl >> 1   */
+		emit(ctx, srlv, t1, t1, t2);               /* t1 = t1 >> t2  */
+		emit(ctx, sllv, lo(dst), lo(dst), src);    /* dl = dl << src */
+		emit(ctx, sllv, hi(dst), hi(dst), src);    /* dh = dh << src */
+		emit(ctx, or, hi(dst), hi(dst), t1);       /* dh = dh | t1   */
+		break;
+	/* dst = dst >> src */
+	case BPF_RSH:
+		/* Next: shift >= 32 */
+		emit(ctx, srlv, lo(dst), hi(dst), src);    /* dl = dh >> src */
+		emit(ctx, move, hi(dst), MIPS_R_ZERO);     /* dh = 0         */
+		emit(ctx, b, 20);                          /* PC += 20       */
+		/* +16: shift < 32 */
+		emit(ctx, sll, t1, hi(dst), 1);            /* t1 = dl << 1   */
+		emit(ctx, sllv, t1, t1, t2);               /* t1 = t1 << t2  */
+		emit(ctx, srlv, lo(dst), lo(dst), src);    /* dl = dl >> src */
+		emit(ctx, srlv, hi(dst), hi(dst), src);    /* dh = dh >> src */
+		emit(ctx, or, lo(dst), lo(dst), t1);       /* dl = dl | t1   */
+		break;
+	/* dst = dst >> src (arithmetic) */
+	case BPF_ARSH:
+		/* Next: shift >= 32 */
+		emit(ctx, srav, lo(dst), hi(dst), src);   /* dl = dh >>a src */
+		emit(ctx, sra, hi(dst), hi(dst), 31);     /* dh = dh >>a 31  */
+		emit(ctx, b, 20);                         /* PC += 20        */
+		/* +16: shift < 32 */
+		emit(ctx, sll, t1, hi(dst), 1);           /* t1 = dl << 1    */
+		emit(ctx, sllv, t1, t1, t2);              /* t1 = t1 << t2   */
+		emit(ctx, srlv, lo(dst), lo(dst), src);   /* dl = dl >>a src */
+		emit(ctx, srav, hi(dst), hi(dst), src);   /* dh = dh >> src  */
+		emit(ctx, or, lo(dst), lo(dst), t1);      /* dl = dl | t1    */
+		break;
+	}
+
+	/* +20: Done */
+	clobber_reg64(ctx, dst);
+}
+
+/* ALU mul immediate (64x32-bit) */
+static void emit_mul_i64(struct jit_context *ctx, const u8 dst[], s32 imm)
+{
+	u8 src = MIPS_R_T6;
+	u8 tmp = MIPS_R_T9;
+
+	switch (imm) {
+	/* dst = dst * 1 is a no-op */
+	case 1:
+		break;
+	/* dst = dst * -1 */
+	case -1:
+		emit_neg_i64(ctx, dst);
+		break;
+	case 0:
+		emit_mov_r(ctx, lo(dst), MIPS_R_ZERO);
+		emit_mov_r(ctx, hi(dst), MIPS_R_ZERO);
+		break;
+	/* Full 64x32 multiply */
+	default:
+		/* hi(dst) = hi(dst) * src(imm) */
+		emit_mov_i(ctx, src, imm);
+		if (cpu_has_mips32r1 || cpu_has_mips32r6) {
+			emit(ctx, mul, hi(dst), hi(dst), src);
+		} else {
+			emit(ctx, multu, hi(dst), src);
+			emit(ctx, mflo, hi(dst));
+		}
+
+		/* hi(dst) = hi(dst) - lo(dst) */
+		if (imm < 0)
+			emit(ctx, subu, hi(dst), hi(dst), lo(dst));
+
+		/* tmp = lo(dst) * src(imm) >> 32 */
+		/* lo(dst) = lo(dst) * src(imm) */
+		if (cpu_has_mips32r6) {
+			emit(ctx, muhu, tmp, lo(dst), src);
+			emit(ctx, mulu, lo(dst), lo(dst), src);
+		} else {
+			emit(ctx, multu, lo(dst), src);
+			emit(ctx, mflo, lo(dst));
+			emit(ctx, mfhi, tmp);
+		}
+
+		/* hi(dst) += tmp */
+		emit(ctx, addu, hi(dst), hi(dst), tmp);
+		clobber_reg64(ctx, dst);
+		break;
+	}
+}
+
+/* ALU mul register (64x64-bit) */
+static void emit_mul_r64(struct jit_context *ctx,
+			 const u8 dst[], const u8 src[])
+{
+	u8 acc = MIPS_R_T8;
+	u8 tmp = MIPS_R_T9;
+
+	/* acc = hi(dst) * lo(src) */
+	if (cpu_has_mips32r1 || cpu_has_mips32r6) {
+		emit(ctx, mul, acc, hi(dst), lo(src));
+	} else {
+		emit(ctx, multu, hi(dst), lo(src));
+		emit(ctx, mflo, acc);
+	}
+
+	/* tmp = lo(dst) * hi(src) */
+	if (cpu_has_mips32r1 || cpu_has_mips32r6) {
+		emit(ctx, mul, tmp, lo(dst), hi(src));
+	} else {
+		emit(ctx, multu, lo(dst), hi(src));
+		emit(ctx, mflo, tmp);
+	}
+
+	/* acc += tmp */
+	emit(ctx, addu, acc, acc, tmp);
+
+	/* tmp = lo(dst) * lo(src) >> 32 */
+	/* lo(dst) = lo(dst) * lo(src) */
+	if (cpu_has_mips32r6) {
+		emit(ctx, muhu, tmp, lo(dst), lo(src));
+		emit(ctx, mulu, lo(dst), lo(dst), lo(src));
+	} else {
+		emit(ctx, multu, lo(dst), lo(src));
+		emit(ctx, mflo, lo(dst));
+		emit(ctx, mfhi, tmp);
+	}
+
+	/* hi(dst) = acc + tmp */
+	emit(ctx, addu, hi(dst), acc, tmp);
+	clobber_reg64(ctx, dst);
+}
+
+/* Helper function for 64-bit modulo */
+static u64 jit_mod64(u64 a, u64 b)
+{
+	u64 rem;
+
+	div64_u64_rem(a, b, &rem);
+	return rem;
+}
+
+/* ALU div/mod register (64-bit) */
+static void emit_divmod_r64(struct jit_context *ctx,
+			    const u8 dst[], const u8 src[], u8 op)
+{
+	const u8 *r0 = bpf2mips32[BPF_REG_0]; /* Mapped to v0-v1 */
+	const u8 *r1 = bpf2mips32[BPF_REG_1]; /* Mapped to a0-a1 */
+	const u8 *r2 = bpf2mips32[BPF_REG_2]; /* Mapped to a2-a3 */
+	int exclude, k;
+	u32 addr = 0;
+
+	/* Push caller-saved registers on stack */
+	push_regs(ctx, ctx->clobbered & JIT_CALLER_REGS,
+		  0, JIT_RESERVED_STACK);
+
+	/* Put 64-bit arguments 1 and 2 in registers a0-a3 */
+	for (k = 0; k < 2; k++) {
+		emit(ctx, move, MIPS_R_T9, src[k]);
+		emit(ctx, move, r1[k], dst[k]);
+		emit(ctx, move, r2[k], MIPS_R_T9);
+	}
+
+	/* Emit function call */
+	switch (BPF_OP(op)) {
+	/* dst = dst / src */
+	case BPF_DIV:
+		addr = (u32)&div64_u64;
+		break;
+	/* dst = dst % src */
+	case BPF_MOD:
+		addr = (u32)&jit_mod64;
+		break;
+	}
+	emit_mov_i(ctx, MIPS_R_T9, addr);
+	emit(ctx, jalr, MIPS_R_RA, MIPS_R_T9);
+	emit(ctx, nop); /* Delay slot */
+
+	/* Store the 64-bit result in dst */
+	emit(ctx, move, dst[0], r0[0]);
+	emit(ctx, move, dst[1], r0[1]);
+
+	/* Restore caller-saved registers, excluding the computed result */
+	exclude = BIT(lo(dst)) | BIT(hi(dst));
+	pop_regs(ctx, ctx->clobbered & JIT_CALLER_REGS,
+		 exclude, JIT_RESERVED_STACK);
+	emit_load_delay(ctx);
+
+	clobber_reg64(ctx, dst);
+	clobber_reg(ctx, MIPS_R_V0);
+	clobber_reg(ctx, MIPS_R_V1);
+	clobber_reg(ctx, MIPS_R_RA);
+}
+
+/* Swap bytes in a register word */
+static void emit_swap8_r(struct jit_context *ctx, u8 dst, u8 src, u8 mask)
+{
+	u8 tmp = MIPS_R_T9;
+
+	emit(ctx, and, tmp, src, mask); /* tmp = src & 0x00ff00ff */
+	emit(ctx, sll, tmp, tmp, 8);    /* tmp = tmp << 8         */
+	emit(ctx, srl, dst, src, 8);    /* dst = src >> 8         */
+	emit(ctx, and, dst, dst, mask); /* dst = dst & 0x00ff00ff */
+	emit(ctx, or,  dst, dst, tmp);  /* dst = dst | tmp        */
+}
+
+/* Swap half words in a register word */
+static void emit_swap16_r(struct jit_context *ctx, u8 dst, u8 src)
+{
+	u8 tmp = MIPS_R_T9;
+
+	emit(ctx, sll, tmp, src, 16);  /* tmp = src << 16 */
+	emit(ctx, srl, dst, src, 16);  /* dst = src >> 16 */
+	emit(ctx, or,  dst, dst, tmp); /* dst = dst | tmp */
+}
+
+/* Swap bytes and truncate a register double word, word or half word */
+static void emit_bswap_r64(struct jit_context *ctx, const u8 dst[], u32 width)
+{
+	u8 tmp = MIPS_R_T8;
+
+	switch (width) {
+	/* Swap bytes in a double word */
+	case 64:
+		if (cpu_has_mips32r2 || cpu_has_mips32r6) {
+			emit(ctx, rotr, tmp, hi(dst), 16);
+			emit(ctx, rotr, hi(dst), lo(dst), 16);
+			emit(ctx, wsbh, lo(dst), tmp);
+			emit(ctx, wsbh, hi(dst), hi(dst));
+		} else {
+			emit_swap16_r(ctx, tmp, lo(dst));
+			emit_swap16_r(ctx, lo(dst), hi(dst));
+			emit(ctx, move, hi(dst), tmp);
+
+			emit(ctx, lui, tmp, 0xff);      /* tmp = 0x00ff0000 */
+			emit(ctx, ori, tmp, tmp, 0xff); /* tmp = 0x00ff00ff */
+			emit_swap8_r(ctx, lo(dst), lo(dst), tmp);
+			emit_swap8_r(ctx, hi(dst), hi(dst), tmp);
+		}
+		break;
+	/* Swap bytes in a word */
+	/* Swap bytes in a half word */
+	case 32:
+	case 16:
+		emit_bswap_r(ctx, lo(dst), width);
+		emit(ctx, move, hi(dst), MIPS_R_ZERO);
+		break;
+	}
+	clobber_reg64(ctx, dst);
+}
+
+/* Truncate a register double word, word or half word */
+static void emit_trunc_r64(struct jit_context *ctx, const u8 dst[], u32 width)
+{
+	switch (width) {
+	case 64:
+		break;
+	/* Zero-extend a word */
+	case 32:
+		emit(ctx, move, hi(dst), MIPS_R_ZERO);
+		clobber_reg(ctx, hi(dst));
+		break;
+	/* Zero-extend a half word */
+	case 16:
+		emit(ctx, move, hi(dst), MIPS_R_ZERO);
+		emit(ctx, andi, lo(dst), lo(dst), 0xffff);
+		clobber_reg64(ctx, dst);
+		break;
+	}
+}
+
+/* Load operation: dst = *(size*)(src + off) */
+static void emit_ldx(struct jit_context *ctx,
+		     const u8 dst[], u8 src, s16 off, u8 size)
+{
+	switch (size) {
+	/* Load a byte */
+	case BPF_B:
+		emit(ctx, lbu, lo(dst), off, src);
+		emit(ctx, move, hi(dst), MIPS_R_ZERO);
+		break;
+	/* Load a half word */
+	case BPF_H:
+		emit(ctx, lhu, lo(dst), off, src);
+		emit(ctx, move, hi(dst), MIPS_R_ZERO);
+		break;
+	/* Load a word */
+	case BPF_W:
+		emit(ctx, lw, lo(dst), off, src);
+		emit(ctx, move, hi(dst), MIPS_R_ZERO);
+		break;
+	/* Load a double word */
+	case BPF_DW:
+		if (dst[1] == src) {
+			emit(ctx, lw, dst[0], off + 4, src);
+			emit(ctx, lw, dst[1], off, src);
+		} else {
+			emit(ctx, lw, dst[1], off, src);
+			emit(ctx, lw, dst[0], off + 4, src);
+		}
+		emit_load_delay(ctx);
+		break;
+	}
+	clobber_reg64(ctx, dst);
+}
+
+/* Store operation: *(size *)(dst + off) = src */
+static void emit_stx(struct jit_context *ctx,
+		     const u8 dst, const u8 src[], s16 off, u8 size)
+{
+	switch (size) {
+	/* Store a byte */
+	case BPF_B:
+		emit(ctx, sb, lo(src), off, dst);
+		break;
+	/* Store a half word */
+	case BPF_H:
+		emit(ctx, sh, lo(src), off, dst);
+		break;
+	/* Store a word */
+	case BPF_W:
+		emit(ctx, sw, lo(src), off, dst);
+		break;
+	/* Store a double word */
+	case BPF_DW:
+		emit(ctx, sw, src[1], off, dst);
+		emit(ctx, sw, src[0], off + 4, dst);
+		break;
+	}
+}
+
+/* Atomic read-modify-write (32-bit, non-ll/sc fallback) */
+static void emit_atomic_r32(struct jit_context *ctx,
+			    u8 dst, u8 src, s16 off, u8 code)
+{
+	u32 exclude = 0;
+	u32 addr = 0;
+
+	/* Push caller-saved registers on stack */
+	push_regs(ctx, ctx->clobbered & JIT_CALLER_REGS,
+		  0, JIT_RESERVED_STACK);
+	/*
+	 * Argument 1: dst+off if xchg, otherwise src, passed in register a0
+	 * Argument 2: src if xchg, otherwise dst+off, passed in register a1
+	 */
+	emit(ctx, move, MIPS_R_T9, dst);
+	if (code == BPF_XCHG) {
+		emit(ctx, move, MIPS_R_A1, src);
+		emit(ctx, addiu, MIPS_R_A0, MIPS_R_T9, off);
+	} else {
+		emit(ctx, move, MIPS_R_A0, src);
+		emit(ctx, addiu, MIPS_R_A1, MIPS_R_T9, off);
+	}
+
+	/* Emit function call */
+	switch (code) {
+	case BPF_ADD:
+		addr = (u32)&atomic_add;
+		break;
+	case BPF_ADD | BPF_FETCH:
+		addr = (u32)&atomic_fetch_add;
+		break;
+	case BPF_SUB:
+		addr = (u32)&atomic_sub;
+		break;
+	case BPF_SUB | BPF_FETCH:
+		addr = (u32)&atomic_fetch_sub;
+		break;
+	case BPF_OR:
+		addr = (u32)&atomic_or;
+		break;
+	case BPF_OR | BPF_FETCH:
+		addr = (u32)&atomic_fetch_or;
+		break;
+	case BPF_AND:
+		addr = (u32)&atomic_and;
+		break;
+	case BPF_AND | BPF_FETCH:
+		addr = (u32)&atomic_fetch_and;
+		break;
+	case BPF_XOR:
+		addr = (u32)&atomic_xor;
+		break;
+	case BPF_XOR | BPF_FETCH:
+		addr = (u32)&atomic_fetch_xor;
+		break;
+	case BPF_XCHG:
+		addr = (u32)&atomic_xchg;
+		break;
+	}
+	emit_mov_i(ctx, MIPS_R_T9, addr);
+	emit(ctx, jalr, MIPS_R_RA, MIPS_R_T9);
+	emit(ctx, nop); /* Delay slot */
+
+	/* Update src register with old value, if specified */
+	if (code & BPF_FETCH) {
+		emit(ctx, move, src, MIPS_R_V0);
+		exclude = BIT(src);
+		clobber_reg(ctx, src);
+	}
+
+	/* Restore caller-saved registers, except any fetched value */
+	pop_regs(ctx, ctx->clobbered & JIT_CALLER_REGS,
+		 exclude, JIT_RESERVED_STACK);
+	emit_load_delay(ctx);
+	clobber_reg(ctx, MIPS_R_RA);
+}
+
+/* Helper function for 64-bit atomic exchange */
+static s64 jit_xchg64(s64 a, atomic64_t *v)
+{
+	return atomic64_xchg(v, a);
+}
+
+/* Atomic read-modify-write (64-bit) */
+static void emit_atomic_r64(struct jit_context *ctx,
+			    u8 dst, const u8 src[], s16 off, u8 code)
+{
+	const u8 *r0 = bpf2mips32[BPF_REG_0]; /* Mapped to v0-v1 */
+	const u8 *r1 = bpf2mips32[BPF_REG_1]; /* Mapped to a0-a1 */
+	u32 exclude = 0;
+	u32 addr = 0;
+
+	/* Push caller-saved registers on stack */
+	push_regs(ctx, ctx->clobbered & JIT_CALLER_REGS,
+		  0, JIT_RESERVED_STACK);
+	/*
+	 * Argument 1: 64-bit src, passed in registers a0-a1
+	 * Argument 2: 32-bit dst+off, passed in register a2
+	 */
+	emit(ctx, move, MIPS_R_T9, dst);
+	emit(ctx, move, r1[0], src[0]);
+	emit(ctx, move, r1[1], src[1]);
+	emit(ctx, addiu, MIPS_R_A2, MIPS_R_T9, off);
+
+	/* Emit function call */
+	switch (code) {
+	case BPF_ADD:
+		addr = (u32)&atomic64_add;
+		break;
+	case BPF_ADD | BPF_FETCH:
+		addr = (u32)&atomic64_fetch_add;
+		break;
+	case BPF_SUB:
+		addr = (u32)&atomic64_sub;
+		break;
+	case BPF_SUB | BPF_FETCH:
+		addr = (u32)&atomic64_fetch_sub;
+		break;
+	case BPF_OR:
+		addr = (u32)&atomic64_or;
+		break;
+	case BPF_OR | BPF_FETCH:
+		addr = (u32)&atomic64_fetch_or;
+		break;
+	case BPF_AND:
+		addr = (u32)&atomic64_and;
+		break;
+	case BPF_AND | BPF_FETCH:
+		addr = (u32)&atomic64_fetch_and;
+		break;
+	case BPF_XOR:
+		addr = (u32)&atomic64_xor;
+		break;
+	case BPF_XOR | BPF_FETCH:
+		addr = (u32)&atomic64_fetch_xor;
+		break;
+	case BPF_XCHG:
+		addr = (u32)&jit_xchg64;
+		break;
+	}
+	emit_mov_i(ctx, MIPS_R_T9, addr);
+	emit(ctx, jalr, MIPS_R_RA, MIPS_R_T9);
+	emit(ctx, nop); /* Delay slot */
+
+	/* Update src register with old value, if specified */
+	if (code & BPF_FETCH) {
+		emit(ctx, move, lo(src), lo(r0));
+		emit(ctx, move, hi(src), hi(r0));
+		exclude = BIT(src[0]) | BIT(src[1]);
+		clobber_reg64(ctx, src);
+	}
+
+	/* Restore caller-saved registers, except any fetched value */
+	pop_regs(ctx, ctx->clobbered & JIT_CALLER_REGS,
+		 exclude, JIT_RESERVED_STACK);
+	emit_load_delay(ctx);
+	clobber_reg(ctx, MIPS_R_RA);
+}
+
+/* Atomic compare-and-exchange (32-bit, non-ll/sc fallback) */
+static void emit_cmpxchg_r32(struct jit_context *ctx, u8 dst, u8 src, s16 off)
+{
+	const u8 *r0 = bpf2mips32[BPF_REG_0];
+
+	/* Push caller-saved registers on stack */
+	push_regs(ctx, ctx->clobbered & JIT_CALLER_REGS,
+		  JIT_RETURN_REGS, JIT_RESERVED_STACK + 2 * sizeof(u32));
+	/*
+	 * Argument 1: 32-bit dst+off, passed in register a0
+	 * Argument 2: 32-bit r0, passed in register a1
+	 * Argument 3: 32-bit src, passed in register a2
+	 */
+	emit(ctx, addiu, MIPS_R_T9, dst, off);
+	emit(ctx, move, MIPS_R_T8, src);
+	emit(ctx, move, MIPS_R_A1, lo(r0));
+	emit(ctx, move, MIPS_R_A0, MIPS_R_T9);
+	emit(ctx, move, MIPS_R_A2, MIPS_R_T8);
+
+	/* Emit function call */
+	emit_mov_i(ctx, MIPS_R_T9, (u32)&atomic_cmpxchg);
+	emit(ctx, jalr, MIPS_R_RA, MIPS_R_T9);
+	emit(ctx, nop); /* Delay slot */
+
+#ifdef __BIG_ENDIAN
+	emit(ctx, move, lo(r0), MIPS_R_V0);
+#endif
+	/* Restore caller-saved registers, except the return value */
+	pop_regs(ctx, ctx->clobbered & JIT_CALLER_REGS,
+		 JIT_RETURN_REGS, JIT_RESERVED_STACK + 2 * sizeof(u32));
+	emit_load_delay(ctx);
+	clobber_reg(ctx, MIPS_R_V0);
+	clobber_reg(ctx, MIPS_R_V1);
+	clobber_reg(ctx, MIPS_R_RA);
+}
+
+/* Atomic compare-and-exchange (64-bit) */
+static void emit_cmpxchg_r64(struct jit_context *ctx,
+			     u8 dst, const u8 src[], s16 off)
+{
+	const u8 *r0 = bpf2mips32[BPF_REG_0];
+	const u8 *r2 = bpf2mips32[BPF_REG_2];
+
+	/* Push caller-saved registers on stack */
+	push_regs(ctx, ctx->clobbered & JIT_CALLER_REGS,
+		  JIT_RETURN_REGS, JIT_RESERVED_STACK + 2 * sizeof(u32));
+	/*
+	 * Argument 1: 32-bit dst+off, passed in register a0 (a1 unused)
+	 * Argument 2: 64-bit r0, passed in registers a2-a3
+	 * Argument 3: 64-bit src, passed on stack
+	 */
+	push_regs(ctx, BIT(src[0]) | BIT(src[1]), 0, JIT_RESERVED_STACK);
+	emit(ctx, addiu, MIPS_R_T9, dst, off);
+	emit(ctx, move, r2[0], r0[0]);
+	emit(ctx, move, r2[1], r0[1]);
+	emit(ctx, move, MIPS_R_A0, MIPS_R_T9);
+
+	/* Emit function call */
+	emit_mov_i(ctx, MIPS_R_T9, (u32)&atomic64_cmpxchg);
+	emit(ctx, jalr, MIPS_R_RA, MIPS_R_T9);
+	emit(ctx, nop); /* Delay slot */
+
+	/* Restore caller-saved registers, except the return value */
+	pop_regs(ctx, ctx->clobbered & JIT_CALLER_REGS,
+		 JIT_RETURN_REGS, JIT_RESERVED_STACK + 2 * sizeof(u32));
+	emit_load_delay(ctx);
+	clobber_reg(ctx, MIPS_R_V0);
+	clobber_reg(ctx, MIPS_R_V1);
+	clobber_reg(ctx, MIPS_R_RA);
+}
+
+/*
+ * Conditional movz or an emulated equivalent.
+ * Note that the rs register may be modified.
+ */
+static void emit_movz_r(struct jit_context *ctx, u8 rd, u8 rs, u8 rt)
+{
+	if (cpu_has_mips_2) {
+		emit(ctx, movz, rd, rs, rt);           /* rd = rt ? rd : rs  */
+	} else if (cpu_has_mips32r6) {
+		if (rs != MIPS_R_ZERO)
+			emit(ctx, seleqz, rs, rs, rt); /* rs = 0 if rt == 0  */
+		emit(ctx, selnez, rd, rd, rt);         /* rd = 0 if rt != 0  */
+		if (rs != MIPS_R_ZERO)
+			emit(ctx, or, rd, rd, rs);     /* rd = rd | rs       */
+	} else {
+		emit(ctx, bnez, rt, 8);                /* PC += 8 if rd != 0 */
+		emit(ctx, nop);                        /* +0: delay slot     */
+		emit(ctx, or, rd, rs, MIPS_R_ZERO);    /* +4: rd = rs        */
+	}
+	clobber_reg(ctx, rd);
+	clobber_reg(ctx, rs);
+}
+
+/*
+ * Conditional movn or an emulated equivalent.
+ * Note that the rs register may be modified.
+ */
+static void emit_movn_r(struct jit_context *ctx, u8 rd, u8 rs, u8 rt)
+{
+	if (cpu_has_mips_2) {
+		emit(ctx, movn, rd, rs, rt);           /* rd = rt ? rs : rd  */
+	} else if (cpu_has_mips32r6) {
+		if (rs != MIPS_R_ZERO)
+			emit(ctx, selnez, rs, rs, rt); /* rs = 0 if rt == 0  */
+		emit(ctx, seleqz, rd, rd, rt);         /* rd = 0 if rt != 0  */
+		if (rs != MIPS_R_ZERO)
+			emit(ctx, or, rd, rd, rs);     /* rd = rd | rs       */
+	} else {
+		emit(ctx, beqz, rt, 8);                /* PC += 8 if rd == 0 */
+		emit(ctx, nop);                        /* +0: delay slot     */
+		emit(ctx, or, rd, rs, MIPS_R_ZERO);    /* +4: rd = rs        */
+	}
+	clobber_reg(ctx, rd);
+	clobber_reg(ctx, rs);
+}
+
+/* Emulation of 64-bit sltiu rd, rs, imm, where imm may be S32_MAX + 1 */
+static void emit_sltiu_r64(struct jit_context *ctx, u8 rd,
+			   const u8 rs[], s64 imm)
+{
+	u8 tmp = MIPS_R_T9;
+
+	if (imm < 0) {
+		emit_mov_i(ctx, rd, imm);                 /* rd = imm        */
+		emit(ctx, sltu, rd, lo(rs), rd);          /* rd = rsl < rd   */
+		emit(ctx, sltiu, tmp, hi(rs), -1);        /* tmp = rsh < ~0U */
+		emit(ctx, or, rd, rd, tmp);               /* rd = rd | tmp   */
+	} else { /* imm >= 0 */
+		if (imm > 0x7fff) {
+			emit_mov_i(ctx, rd, (s32)imm);     /* rd = imm       */
+			emit(ctx, sltu, rd, lo(rs), rd);   /* rd = rsl < rd  */
+		} else {
+			emit(ctx, sltiu, rd, lo(rs), imm); /* rd = rsl < imm */
+		}
+		emit_movn_r(ctx, rd, MIPS_R_ZERO, hi(rs)); /* rd = 0 if rsh  */
+	}
+}
+
+/* Emulation of 64-bit sltu rd, rs, rt */
+static void emit_sltu_r64(struct jit_context *ctx, u8 rd,
+			  const u8 rs[], const u8 rt[])
+{
+	u8 tmp = MIPS_R_T9;
+
+	emit(ctx, sltu, rd, lo(rs), lo(rt));           /* rd = rsl < rtl     */
+	emit(ctx, subu, tmp, hi(rs), hi(rt));          /* tmp = rsh - rth    */
+	emit_movn_r(ctx, rd, MIPS_R_ZERO, tmp);        /* rd = 0 if tmp != 0 */
+	emit(ctx, sltu, tmp, hi(rs), hi(rt));          /* tmp = rsh < rth    */
+	emit(ctx, or, rd, rd, tmp);                    /* rd = rd | tmp      */
+}
+
+/* Emulation of 64-bit slti rd, rs, imm, where imm may be S32_MAX + 1 */
+static void emit_slti_r64(struct jit_context *ctx, u8 rd,
+			  const u8 rs[], s64 imm)
+{
+	u8 t1 = MIPS_R_T8;
+	u8 t2 = MIPS_R_T9;
+	u8 cmp;
+
+	/*
+	 * if ((rs < 0) ^ (imm < 0)) t1 = imm >u rsl
+	 * else                      t1 = rsl <u imm
+	 */
+	emit_mov_i(ctx, rd, (s32)imm);
+	emit(ctx, sltu, t1, lo(rs), rd);               /* t1 = rsl <u imm   */
+	emit(ctx, sltu, t2, rd, lo(rs));               /* t2 = imm <u rsl   */
+	emit(ctx, srl, rd, hi(rs), 31);                /* rd = rsh >> 31    */
+	if (imm < 0)
+		emit_movz_r(ctx, t1, t2, rd);          /* t1 = rd ? t1 : t2 */
+	else
+		emit_movn_r(ctx, t1, t2, rd);          /* t1 = rd ? t2 : t1 */
+	/*
+	 * if ((imm < 0 && rsh != 0xffffffff) ||
+	 *     (imm >= 0 && rsh != 0))
+	 *      t1 = 0
+	 */
+	if (imm < 0) {
+		emit(ctx, addiu, rd, hi(rs), 1);       /* rd = rsh + 1 */
+		cmp = rd;
+	} else { /* imm >= 0 */
+		cmp = hi(rs);
+	}
+	emit_movn_r(ctx, t1, MIPS_R_ZERO, cmp);        /* t1 = 0 if cmp != 0 */
+
+	/*
+	 * if (imm < 0) rd = rsh < -1
+	 * else         rd = rsh != 0
+	 * rd = rd | t1
+	 */
+	emit(ctx, slti, rd, hi(rs), imm < 0 ? -1 : 0); /* rd = rsh < hi(imm) */
+	emit(ctx, or, rd, rd, t1);                     /* rd = rd | t1       */
+}
+
+/* Emulation of 64-bit(slt rd, rs, rt) */
+static void emit_slt_r64(struct jit_context *ctx, u8 rd,
+			 const u8 rs[], const u8 rt[])
+{
+	u8 t1 = MIPS_R_T7;
+	u8 t2 = MIPS_R_T8;
+	u8 t3 = MIPS_R_T9;
+
+	/*
+	 * if ((rs < 0) ^ (rt < 0)) t1 = rtl <u rsl
+	 * else                     t1 = rsl <u rtl
+	 * if (rsh == rth)          t1 = 0
+	 */
+	emit(ctx, sltu, t1, lo(rs), lo(rt));           /* t1 = rsl <u rtl   */
+	emit(ctx, sltu, t2, lo(rt), lo(rs));           /* t2 = rtl <u rsl   */
+	emit(ctx, xor, t3, hi(rs), hi(rt));            /* t3 = rlh ^ rth    */
+	emit(ctx, srl, rd, t3, 31);                    /* rd = t3 >> 31     */
+	emit_movn_r(ctx, t1, t2, rd);                  /* t1 = rd ? t2 : t1 */
+	emit_movn_r(ctx, t1, MIPS_R_ZERO, t3);         /* t1 = 0 if t3 != 0 */
+
+	/* rd = (rsh < rth) | t1 */
+	emit(ctx, slt, rd, hi(rs), hi(rt));            /* rd = rsh <s rth   */
+	emit(ctx, or, rd, rd, t1);                     /* rd = rd | t1      */
+}
+
+/* Jump immediate (64-bit) */
+static void emit_jmp_i64(struct jit_context *ctx,
+			 const u8 dst[], s32 imm, s32 off, u8 op)
+{
+	u8 tmp = MIPS_R_T6;
+
+	switch (op) {
+	/* No-op, used internally for branch optimization */
+	case JIT_JNOP:
+		break;
+	/* PC += off if dst == imm */
+	/* PC += off if dst != imm */
+	case BPF_JEQ:
+	case BPF_JNE:
+		if (imm >= -0x7fff && imm <= 0x8000) {
+			emit(ctx, addiu, tmp, lo(dst), -imm);
+		} else if ((u32)imm <= 0xffff) {
+			emit(ctx, xori, tmp, lo(dst), imm);
+		} else {       /* Register fallback */
+			emit_mov_i(ctx, tmp, imm);
+			emit(ctx, xor, tmp, lo(dst), tmp);
+		}
+		if (imm < 0) { /* Compare sign extension */
+			emit(ctx, addu, MIPS_R_T9, hi(dst), 1);
+			emit(ctx, or, tmp, tmp, MIPS_R_T9);
+		} else {       /* Compare zero extension */
+			emit(ctx, or, tmp, tmp, hi(dst));
+		}
+		if (op == BPF_JEQ)
+			emit(ctx, beqz, tmp, off);
+		else   /* BPF_JNE */
+			emit(ctx, bnez, tmp, off);
+		break;
+	/* PC += off if dst & imm */
+	/* PC += off if (dst & imm) == 0 (not in BPF, used for long jumps) */
+	case BPF_JSET:
+	case JIT_JNSET:
+		if ((u32)imm <= 0xffff) {
+			emit(ctx, andi, tmp, lo(dst), imm);
+		} else {     /* Register fallback */
+			emit_mov_i(ctx, tmp, imm);
+			emit(ctx, and, tmp, lo(dst), tmp);
+		}
+		if (imm < 0) /* Sign-extension pulls in high word */
+			emit(ctx, or, tmp, tmp, hi(dst));
+		if (op == BPF_JSET)
+			emit(ctx, bnez, tmp, off);
+		else   /* JIT_JNSET */
+			emit(ctx, beqz, tmp, off);
+		break;
+	/* PC += off if dst > imm */
+	case BPF_JGT:
+		emit_sltiu_r64(ctx, tmp, dst, (s64)imm + 1);
+		emit(ctx, beqz, tmp, off);
+		break;
+	/* PC += off if dst >= imm */
+	case BPF_JGE:
+		emit_sltiu_r64(ctx, tmp, dst, imm);
+		emit(ctx, beqz, tmp, off);
+		break;
+	/* PC += off if dst < imm */
+	case BPF_JLT:
+		emit_sltiu_r64(ctx, tmp, dst, imm);
+		emit(ctx, bnez, tmp, off);
+		break;
+	/* PC += off if dst <= imm */
+	case BPF_JLE:
+		emit_sltiu_r64(ctx, tmp, dst, (s64)imm + 1);
+		emit(ctx, bnez, tmp, off);
+		break;
+	/* PC += off if dst > imm (signed) */
+	case BPF_JSGT:
+		emit_slti_r64(ctx, tmp, dst, (s64)imm + 1);
+		emit(ctx, beqz, tmp, off);
+		break;
+	/* PC += off if dst >= imm (signed) */
+	case BPF_JSGE:
+		emit_slti_r64(ctx, tmp, dst, imm);
+		emit(ctx, beqz, tmp, off);
+		break;
+	/* PC += off if dst < imm (signed) */
+	case BPF_JSLT:
+		emit_slti_r64(ctx, tmp, dst, imm);
+		emit(ctx, bnez, tmp, off);
+		break;
+	/* PC += off if dst <= imm (signed) */
+	case BPF_JSLE:
+		emit_slti_r64(ctx, tmp, dst, (s64)imm + 1);
+		emit(ctx, bnez, tmp, off);
+		break;
+	}
+}
+
+/* Jump register (64-bit) */
+static void emit_jmp_r64(struct jit_context *ctx,
+			 const u8 dst[], const u8 src[], s32 off, u8 op)
+{
+	u8 t1 = MIPS_R_T6;
+	u8 t2 = MIPS_R_T7;
+
+	switch (op) {
+	/* No-op, used internally for branch optimization */
+	case JIT_JNOP:
+		break;
+	/* PC += off if dst == src */
+	/* PC += off if dst != src */
+	case BPF_JEQ:
+	case BPF_JNE:
+		emit(ctx, subu, t1, lo(dst), lo(src));
+		emit(ctx, subu, t2, hi(dst), hi(src));
+		emit(ctx, or, t1, t1, t2);
+		if (op == BPF_JEQ)
+			emit(ctx, beqz, t1, off);
+		else   /* BPF_JNE */
+			emit(ctx, bnez, t1, off);
+		break;
+	/* PC += off if dst & src */
+	/* PC += off if (dst & imm) == 0 (not in BPF, used for long jumps) */
+	case BPF_JSET:
+	case JIT_JNSET:
+		emit(ctx, and, t1, lo(dst), lo(src));
+		emit(ctx, and, t2, hi(dst), hi(src));
+		emit(ctx, or, t1, t1, t2);
+		if (op == BPF_JSET)
+			emit(ctx, bnez, t1, off);
+		else   /* JIT_JNSET */
+			emit(ctx, beqz, t1, off);
+		break;
+	/* PC += off if dst > src */
+	case BPF_JGT:
+		emit_sltu_r64(ctx, t1, src, dst);
+		emit(ctx, bnez, t1, off);
+		break;
+	/* PC += off if dst >= src */
+	case BPF_JGE:
+		emit_sltu_r64(ctx, t1, dst, src);
+		emit(ctx, beqz, t1, off);
+		break;
+	/* PC += off if dst < src */
+	case BPF_JLT:
+		emit_sltu_r64(ctx, t1, dst, src);
+		emit(ctx, bnez, t1, off);
+		break;
+	/* PC += off if dst <= src */
+	case BPF_JLE:
+		emit_sltu_r64(ctx, t1, src, dst);
+		emit(ctx, beqz, t1, off);
+		break;
+	/* PC += off if dst > src (signed) */
+	case BPF_JSGT:
+		emit_slt_r64(ctx, t1, src, dst);
+		emit(ctx, bnez, t1, off);
+		break;
+	/* PC += off if dst >= src (signed) */
+	case BPF_JSGE:
+		emit_slt_r64(ctx, t1, dst, src);
+		emit(ctx, beqz, t1, off);
+		break;
+	/* PC += off if dst < src (signed) */
+	case BPF_JSLT:
+		emit_slt_r64(ctx, t1, dst, src);
+		emit(ctx, bnez, t1, off);
+		break;
+	/* PC += off if dst <= src (signed) */
+	case BPF_JSLE:
+		emit_slt_r64(ctx, t1, src, dst);
+		emit(ctx, beqz, t1, off);
+		break;
+	}
+}
+
+/* Function call */
+static int emit_call(struct jit_context *ctx, const struct bpf_insn *insn)
+{
+	bool fixed;
+	u64 addr;
+
+	/* Decode the call address */
+	if (bpf_jit_get_func_addr(ctx->program, insn, false,
+				  &addr, &fixed) < 0)
+		return -1;
+	if (!fixed)
+		return -1;
+
+	/* Push stack arguments */
+	push_regs(ctx, JIT_STACK_REGS, 0, JIT_RESERVED_STACK);
+
+	/* Emit function call */
+	emit_mov_i(ctx, MIPS_R_T9, addr);
+	emit(ctx, jalr, MIPS_R_RA, MIPS_R_T9);
+	emit(ctx, nop); /* Delay slot */
+
+	clobber_reg(ctx, MIPS_R_RA);
+	clobber_reg(ctx, MIPS_R_V0);
+	clobber_reg(ctx, MIPS_R_V1);
+	return 0;
+}
+
+/* Function tail call */
+static int emit_tail_call(struct jit_context *ctx)
+{
+	u8 ary = lo(bpf2mips32[BPF_REG_2]);
+	u8 ind = lo(bpf2mips32[BPF_REG_3]);
+	u8 t1 = MIPS_R_T8;
+	u8 t2 = MIPS_R_T9;
+	int off;
+
+	/*
+	 * Tail call:
+	 * eBPF R1   - function argument (context ptr), passed in a0-a1
+	 * eBPF R2   - ptr to object with array of function entry points
+	 * eBPF R3   - array index of function to be called
+	 * stack[sz] - remaining tail call count, initialized in prologue
+	 */
+
+	/* if (ind >= ary->map.max_entries) goto out */
+	off = offsetof(struct bpf_array, map.max_entries);
+	if (off > 0x7fff)
+		return -1;
+	emit(ctx, lw, t1, off, ary);             /* t1 = ary->map.max_entries*/
+	emit_load_delay(ctx);                    /* Load delay slot          */
+	emit(ctx, sltu, t1, ind, t1);            /* t1 = ind < t1            */
+	emit(ctx, beqz, t1, get_offset(ctx, 1)); /* PC += off(1) if t1 == 0  */
+						 /* (next insn delay slot)   */
+	/* if (TCC-- <= 0) goto out */
+	emit(ctx, lw, t2, ctx->stack_size, MIPS_R_SP);  /* t2 = *(SP + size) */
+	emit_load_delay(ctx);                     /* Load delay slot         */
+	emit(ctx, blez, t2, get_offset(ctx, 1));  /* PC += off(1) if t2 <= 0 */
+	emit(ctx, addiu, t2, t2, -1);             /* t2-- (delay slot)       */
+	emit(ctx, sw, t2, ctx->stack_size, MIPS_R_SP);  /* *(SP + size) = t2 */
+
+	/* prog = ary->ptrs[ind] */
+	off = offsetof(struct bpf_array, ptrs);
+	if (off > 0x7fff)
+		return -1;
+	emit(ctx, sll, t1, ind, 2);               /* t1 = ind << 2           */
+	emit(ctx, addu, t1, t1, ary);             /* t1 += ary               */
+	emit(ctx, lw, t2, off, t1);               /* t2 = *(t1 + off)        */
+	emit_load_delay(ctx);                     /* Load delay slot         */
+
+	/* if (prog == 0) goto out */
+	emit(ctx, beqz, t2, get_offset(ctx, 1));  /* PC += off(1) if t2 == 0 */
+	emit(ctx, nop);                           /* Delay slot              */
+
+	/* func = prog->bpf_func + 8 (prologue skip offset) */
+	off = offsetof(struct bpf_prog, bpf_func);
+	if (off > 0x7fff)
+		return -1;
+	emit(ctx, lw, t1, off, t2);                /* t1 = *(t2 + off)       */
+	emit_load_delay(ctx);                      /* Load delay slot        */
+	emit(ctx, addiu, t1, t1, JIT_TCALL_SKIP);  /* t1 += skip (8 or 12)   */
+
+	/* goto func */
+	build_epilogue(ctx, t1);
+	return 0;
+}
+
+/*
+ * Stack frame layout for a JITed program (stack grows down).
+ *
+ * Higher address  : Caller's stack frame       :
+ *                 :----------------------------:
+ *                 : 64-bit eBPF args r3-r5     :
+ *                 :----------------------------:
+ *                 : Reserved / tail call count :
+ *                 +============================+  <--- MIPS sp before call
+ *                 | Callee-saved registers,    |
+ *                 | including RA and FP        |
+ *                 +----------------------------+  <--- eBPF FP (MIPS zero,fp)
+ *                 | Local eBPF variables       |
+ *                 | allocated by program       |
+ *                 +----------------------------+
+ *                 | Reserved for caller-saved  |
+ *                 | registers                  |
+ *                 +----------------------------+
+ *                 | Reserved for 64-bit eBPF   |
+ *                 | args r3-r5 & args passed   |
+ *                 | on stack in kernel calls   |
+ * Lower address   +============================+  <--- MIPS sp
+ */
+
+/* Build program prologue to set up the stack and registers */
+void build_prologue(struct jit_context *ctx)
+{
+	const u8 *r1 = bpf2mips32[BPF_REG_1];
+	const u8 *fp = bpf2mips32[BPF_REG_FP];
+	int stack, saved, locals, reserved;
+
+	/*
+	 * In the unlikely event that the TCC limit is raised to more
+	 * than 16 bits, it is clamped to the maximum value allowed for
+	 * the generated code (0xffff). It is better fail to compile
+	 * instead of degrading gracefully.
+	 */
+	BUILD_BUG_ON(MAX_TAIL_CALL_CNT > 0xffff);
+
+	/*
+	 * The first two instructions initialize TCC in the reserved (for us)
+	 * 16-byte area in the parent's stack frame. On a tail call, the
+	 * calling function jumps into the prologue after these instructions.
+	 */
+	emit(ctx, ori, MIPS_R_T9, MIPS_R_ZERO, MAX_TAIL_CALL_CNT);
+	emit(ctx, sw, MIPS_R_T9, 0, MIPS_R_SP);
+
+	/*
+	 * Register eBPF R1 contains the 32-bit context pointer argument.
+	 * A 32-bit argument is always passed in MIPS register a0, regardless
+	 * of CPU endianness. Initialize R1 accordingly and zero-extend.
+	 */
+#ifdef __BIG_ENDIAN
+	emit(ctx, move, lo(r1), MIPS_R_A0);
+#endif
+
+	/* === Entry-point for tail calls === */
+
+	/* Zero-extend the 32-bit argument */
+	emit(ctx, move, hi(r1), MIPS_R_ZERO);
+
+	/* If the eBPF frame pointer was accessed it must be saved */
+	if (ctx->accessed & BIT(BPF_REG_FP))
+		clobber_reg64(ctx, fp);
+
+	/* Compute the stack space needed for callee-saved registers */
+	saved = hweight32(ctx->clobbered & JIT_CALLEE_REGS) * sizeof(u32);
+	saved = ALIGN(saved, MIPS_STACK_ALIGNMENT);
+
+	/* Stack space used by eBPF program local data */
+	locals = ALIGN(ctx->program->aux->stack_depth, MIPS_STACK_ALIGNMENT);
+
+	/*
+	 * If we are emitting function calls, reserve extra stack space for
+	 * caller-saved registers and function arguments passed on the stack.
+	 * The required space is computed automatically during resource
+	 * usage discovery (pass 1).
+	 */
+	reserved = ctx->stack_used;
+
+	/* Allocate the stack frame */
+	stack = ALIGN(saved + locals + reserved, MIPS_STACK_ALIGNMENT);
+	emit(ctx, addiu, MIPS_R_SP, MIPS_R_SP, -stack);
+
+	/* Store callee-saved registers on stack */
+	push_regs(ctx, ctx->clobbered & JIT_CALLEE_REGS, 0, stack - saved);
+
+	/* Initialize the eBPF frame pointer if accessed */
+	if (ctx->accessed & BIT(BPF_REG_FP))
+		emit(ctx, addiu, lo(fp), MIPS_R_SP, stack - saved);
+
+	ctx->saved_size = saved;
+	ctx->stack_size = stack;
+}
+
+/* Build the program epilogue to restore the stack and registers */
+void build_epilogue(struct jit_context *ctx, int dest_reg)
+{
+	/* Restore callee-saved registers from stack */
+	pop_regs(ctx, ctx->clobbered & JIT_CALLEE_REGS, 0,
+		 ctx->stack_size - ctx->saved_size);
+	/*
+	 * A 32-bit return value is always passed in MIPS register v0,
+	 * but on big-endian targets the low part of R0 is mapped to v1.
+	 */
+#ifdef __BIG_ENDIAN
+	emit(ctx, move, MIPS_R_V0, MIPS_R_V1);
+#endif
+
+	/* Jump to the return address and adjust the stack pointer */
+	emit(ctx, jr, dest_reg);
+	emit(ctx, addiu, MIPS_R_SP, MIPS_R_SP, ctx->stack_size);
+}
+
+/* Build one eBPF instruction */
+int build_insn(const struct bpf_insn *insn, struct jit_context *ctx)
+{
+	const u8 *dst = bpf2mips32[insn->dst_reg];
+	const u8 *src = bpf2mips32[insn->src_reg];
+	const u8 *res = bpf2mips32[BPF_REG_0];
+	const u8 *tmp = bpf2mips32[JIT_REG_TMP];
+	u8 code = insn->code;
+	s16 off = insn->off;
+	s32 imm = insn->imm;
+	s32 val, rel;
+	u8 alu, jmp;
+
+	switch (code) {
+	/* ALU operations */
+	/* dst = imm */
+	case BPF_ALU | BPF_MOV | BPF_K:
+		emit_mov_i(ctx, lo(dst), imm);
+		emit_zext_ver(ctx, dst);
+		break;
+	/* dst = src */
+	case BPF_ALU | BPF_MOV | BPF_X:
+		if (imm == 1) {
+			/* Special mov32 for zext */
+			emit_mov_i(ctx, hi(dst), 0);
+		} else {
+			emit_mov_r(ctx, lo(dst), lo(src));
+			emit_zext_ver(ctx, dst);
+		}
+		break;
+	/* dst = -dst */
+	case BPF_ALU | BPF_NEG:
+		emit_alu_i(ctx, lo(dst), 0, BPF_NEG);
+		emit_zext_ver(ctx, dst);
+		break;
+	/* dst = dst & imm */
+	/* dst = dst | imm */
+	/* dst = dst ^ imm */
+	/* dst = dst << imm */
+	/* dst = dst >> imm */
+	/* dst = dst >> imm (arithmetic) */
+	/* dst = dst + imm */
+	/* dst = dst - imm */
+	/* dst = dst * imm */
+	/* dst = dst / imm */
+	/* dst = dst % imm */
+	case BPF_ALU | BPF_OR | BPF_K:
+	case BPF_ALU | BPF_AND | BPF_K:
+	case BPF_ALU | BPF_XOR | BPF_K:
+	case BPF_ALU | BPF_LSH | BPF_K:
+	case BPF_ALU | BPF_RSH | BPF_K:
+	case BPF_ALU | BPF_ARSH | BPF_K:
+	case BPF_ALU | BPF_ADD | BPF_K:
+	case BPF_ALU | BPF_SUB | BPF_K:
+	case BPF_ALU | BPF_MUL | BPF_K:
+	case BPF_ALU | BPF_DIV | BPF_K:
+	case BPF_ALU | BPF_MOD | BPF_K:
+		if (!valid_alu_i(BPF_OP(code), imm)) {
+			emit_mov_i(ctx, MIPS_R_T6, imm);
+			emit_alu_r(ctx, lo(dst), MIPS_R_T6, BPF_OP(code));
+		} else if (rewrite_alu_i(BPF_OP(code), imm, &alu, &val)) {
+			emit_alu_i(ctx, lo(dst), val, alu);
+		}
+		emit_zext_ver(ctx, dst);
+		break;
+	/* dst = dst & src */
+	/* dst = dst | src */
+	/* dst = dst ^ src */
+	/* dst = dst << src */
+	/* dst = dst >> src */
+	/* dst = dst >> src (arithmetic) */
+	/* dst = dst + src */
+	/* dst = dst - src */
+	/* dst = dst * src */
+	/* dst = dst / src */
+	/* dst = dst % src */
+	case BPF_ALU | BPF_AND | BPF_X:
+	case BPF_ALU | BPF_OR | BPF_X:
+	case BPF_ALU | BPF_XOR | BPF_X:
+	case BPF_ALU | BPF_LSH | BPF_X:
+	case BPF_ALU | BPF_RSH | BPF_X:
+	case BPF_ALU | BPF_ARSH | BPF_X:
+	case BPF_ALU | BPF_ADD | BPF_X:
+	case BPF_ALU | BPF_SUB | BPF_X:
+	case BPF_ALU | BPF_MUL | BPF_X:
+	case BPF_ALU | BPF_DIV | BPF_X:
+	case BPF_ALU | BPF_MOD | BPF_X:
+		emit_alu_r(ctx, lo(dst), lo(src), BPF_OP(code));
+		emit_zext_ver(ctx, dst);
+		break;
+	/* dst = imm (64-bit) */
+	case BPF_ALU64 | BPF_MOV | BPF_K:
+		emit_mov_se_i64(ctx, dst, imm);
+		break;
+	/* dst = src (64-bit) */
+	case BPF_ALU64 | BPF_MOV | BPF_X:
+		emit_mov_r(ctx, lo(dst), lo(src));
+		emit_mov_r(ctx, hi(dst), hi(src));
+		break;
+	/* dst = -dst (64-bit) */
+	case BPF_ALU64 | BPF_NEG:
+		emit_neg_i64(ctx, dst);
+		break;
+	/* dst = dst & imm (64-bit) */
+	case BPF_ALU64 | BPF_AND | BPF_K:
+		emit_alu_i64(ctx, dst, imm, BPF_OP(code));
+		break;
+	/* dst = dst | imm (64-bit) */
+	/* dst = dst ^ imm (64-bit) */
+	/* dst = dst + imm (64-bit) */
+	/* dst = dst - imm (64-bit) */
+	case BPF_ALU64 | BPF_OR | BPF_K:
+	case BPF_ALU64 | BPF_XOR | BPF_K:
+	case BPF_ALU64 | BPF_ADD | BPF_K:
+	case BPF_ALU64 | BPF_SUB | BPF_K:
+		if (imm)
+			emit_alu_i64(ctx, dst, imm, BPF_OP(code));
+		break;
+	/* dst = dst << imm (64-bit) */
+	/* dst = dst >> imm (64-bit) */
+	/* dst = dst >> imm (64-bit, arithmetic) */
+	case BPF_ALU64 | BPF_LSH | BPF_K:
+	case BPF_ALU64 | BPF_RSH | BPF_K:
+	case BPF_ALU64 | BPF_ARSH | BPF_K:
+		if (imm)
+			emit_shift_i64(ctx, dst, imm, BPF_OP(code));
+		break;
+	/* dst = dst * imm (64-bit) */
+	case BPF_ALU64 | BPF_MUL | BPF_K:
+		emit_mul_i64(ctx, dst, imm);
+		break;
+	/* dst = dst / imm (64-bit) */
+	/* dst = dst % imm (64-bit) */
+	case BPF_ALU64 | BPF_DIV | BPF_K:
+	case BPF_ALU64 | BPF_MOD | BPF_K:
+		/*
+		 * Sign-extend the immediate value into a temporary register,
+		 * and then do the operation on this register.
+		 */
+		emit_mov_se_i64(ctx, tmp, imm);
+		emit_divmod_r64(ctx, dst, tmp, BPF_OP(code));
+		break;
+	/* dst = dst & src (64-bit) */
+	/* dst = dst | src (64-bit) */
+	/* dst = dst ^ src (64-bit) */
+	/* dst = dst + src (64-bit) */
+	/* dst = dst - src (64-bit) */
+	case BPF_ALU64 | BPF_AND | BPF_X:
+	case BPF_ALU64 | BPF_OR | BPF_X:
+	case BPF_ALU64 | BPF_XOR | BPF_X:
+	case BPF_ALU64 | BPF_ADD | BPF_X:
+	case BPF_ALU64 | BPF_SUB | BPF_X:
+		emit_alu_r64(ctx, dst, src, BPF_OP(code));
+		break;
+	/* dst = dst << src (64-bit) */
+	/* dst = dst >> src (64-bit) */
+	/* dst = dst >> src (64-bit, arithmetic) */
+	case BPF_ALU64 | BPF_LSH | BPF_X:
+	case BPF_ALU64 | BPF_RSH | BPF_X:
+	case BPF_ALU64 | BPF_ARSH | BPF_X:
+		emit_shift_r64(ctx, dst, lo(src), BPF_OP(code));
+		break;
+	/* dst = dst * src (64-bit) */
+	case BPF_ALU64 | BPF_MUL | BPF_X:
+		emit_mul_r64(ctx, dst, src);
+		break;
+	/* dst = dst / src (64-bit) */
+	/* dst = dst % src (64-bit) */
+	case BPF_ALU64 | BPF_DIV | BPF_X:
+	case BPF_ALU64 | BPF_MOD | BPF_X:
+		emit_divmod_r64(ctx, dst, src, BPF_OP(code));
+		break;
+	/* dst = htole(dst) */
+	/* dst = htobe(dst) */
+	case BPF_ALU | BPF_END | BPF_FROM_LE:
+	case BPF_ALU | BPF_END | BPF_FROM_BE:
+		if (BPF_SRC(code) ==
+#ifdef __BIG_ENDIAN
+		    BPF_FROM_LE
+#else
+		    BPF_FROM_BE
+#endif
+		    )
+			emit_bswap_r64(ctx, dst, imm);
+		else
+			emit_trunc_r64(ctx, dst, imm);
+		break;
+	/* dst = imm64 */
+	case BPF_LD | BPF_IMM | BPF_DW:
+		emit_mov_i(ctx, lo(dst), imm);
+		emit_mov_i(ctx, hi(dst), insn[1].imm);
+		return 1;
+	/* LDX: dst = *(size *)(src + off) */
+	case BPF_LDX | BPF_MEM | BPF_W:
+	case BPF_LDX | BPF_MEM | BPF_H:
+	case BPF_LDX | BPF_MEM | BPF_B:
+	case BPF_LDX | BPF_MEM | BPF_DW:
+		emit_ldx(ctx, dst, lo(src), off, BPF_SIZE(code));
+		break;
+	/* ST: *(size *)(dst + off) = imm */
+	case BPF_ST | BPF_MEM | BPF_W:
+	case BPF_ST | BPF_MEM | BPF_H:
+	case BPF_ST | BPF_MEM | BPF_B:
+	case BPF_ST | BPF_MEM | BPF_DW:
+		switch (BPF_SIZE(code)) {
+		case BPF_DW:
+			/* Sign-extend immediate value into temporary reg */
+			emit_mov_se_i64(ctx, tmp, imm);
+			break;
+		case BPF_W:
+		case BPF_H:
+		case BPF_B:
+			emit_mov_i(ctx, lo(tmp), imm);
+			break;
+		}
+		emit_stx(ctx, lo(dst), tmp, off, BPF_SIZE(code));
+		break;
+	/* STX: *(size *)(dst + off) = src */
+	case BPF_STX | BPF_MEM | BPF_W:
+	case BPF_STX | BPF_MEM | BPF_H:
+	case BPF_STX | BPF_MEM | BPF_B:
+	case BPF_STX | BPF_MEM | BPF_DW:
+		emit_stx(ctx, lo(dst), src, off, BPF_SIZE(code));
+		break;
+	/* Speculation barrier */
+	case BPF_ST | BPF_NOSPEC:
+		break;
+	/* Atomics */
+	case BPF_STX | BPF_ATOMIC | BPF_W:
+		switch (imm) {
+		case BPF_ADD:
+		case BPF_ADD | BPF_FETCH:
+		case BPF_AND:
+		case BPF_AND | BPF_FETCH:
+		case BPF_OR:
+		case BPF_OR | BPF_FETCH:
+		case BPF_XOR:
+		case BPF_XOR | BPF_FETCH:
+		case BPF_XCHG:
+			if (cpu_has_llsc)
+				emit_atomic_r(ctx, lo(dst), lo(src), off, imm);
+			else /* Non-ll/sc fallback */
+				emit_atomic_r32(ctx, lo(dst), lo(src),
+						off, imm);
+			if (imm & BPF_FETCH)
+				emit_zext_ver(ctx, src);
+			break;
+		case BPF_CMPXCHG:
+			if (cpu_has_llsc)
+				emit_cmpxchg_r(ctx, lo(dst), lo(src),
+					       lo(res), off);
+			else /* Non-ll/sc fallback */
+				emit_cmpxchg_r32(ctx, lo(dst), lo(src), off);
+			/* Result zero-extension inserted by verifier */
+			break;
+		default:
+			goto notyet;
+		}
+		break;
+	/* Atomics (64-bit) */
+	case BPF_STX | BPF_ATOMIC | BPF_DW:
+		switch (imm) {
+		case BPF_ADD:
+		case BPF_ADD | BPF_FETCH:
+		case BPF_AND:
+		case BPF_AND | BPF_FETCH:
+		case BPF_OR:
+		case BPF_OR | BPF_FETCH:
+		case BPF_XOR:
+		case BPF_XOR | BPF_FETCH:
+		case BPF_XCHG:
+			emit_atomic_r64(ctx, lo(dst), src, off, imm);
+			break;
+		case BPF_CMPXCHG:
+			emit_cmpxchg_r64(ctx, lo(dst), src, off);
+			break;
+		default:
+			goto notyet;
+		}
+		break;
+	/* PC += off if dst == src */
+	/* PC += off if dst != src */
+	/* PC += off if dst & src */
+	/* PC += off if dst > src */
+	/* PC += off if dst >= src */
+	/* PC += off if dst < src */
+	/* PC += off if dst <= src */
+	/* PC += off if dst > src (signed) */
+	/* PC += off if dst >= src (signed) */
+	/* PC += off if dst < src (signed) */
+	/* PC += off if dst <= src (signed) */
+	case BPF_JMP32 | BPF_JEQ | BPF_X:
+	case BPF_JMP32 | BPF_JNE | BPF_X:
+	case BPF_JMP32 | BPF_JSET | BPF_X:
+	case BPF_JMP32 | BPF_JGT | BPF_X:
+	case BPF_JMP32 | BPF_JGE | BPF_X:
+	case BPF_JMP32 | BPF_JLT | BPF_X:
+	case BPF_JMP32 | BPF_JLE | BPF_X:
+	case BPF_JMP32 | BPF_JSGT | BPF_X:
+	case BPF_JMP32 | BPF_JSGE | BPF_X:
+	case BPF_JMP32 | BPF_JSLT | BPF_X:
+	case BPF_JMP32 | BPF_JSLE | BPF_X:
+		if (off == 0)
+			break;
+		setup_jmp_r(ctx, dst == src, BPF_OP(code), off, &jmp, &rel);
+		emit_jmp_r(ctx, lo(dst), lo(src), rel, jmp);
+		if (finish_jmp(ctx, jmp, off) < 0)
+			goto toofar;
+		break;
+	/* PC += off if dst == imm */
+	/* PC += off if dst != imm */
+	/* PC += off if dst & imm */
+	/* PC += off if dst > imm */
+	/* PC += off if dst >= imm */
+	/* PC += off if dst < imm */
+	/* PC += off if dst <= imm */
+	/* PC += off if dst > imm (signed) */
+	/* PC += off if dst >= imm (signed) */
+	/* PC += off if dst < imm (signed) */
+	/* PC += off if dst <= imm (signed) */
+	case BPF_JMP32 | BPF_JEQ | BPF_K:
+	case BPF_JMP32 | BPF_JNE | BPF_K:
+	case BPF_JMP32 | BPF_JSET | BPF_K:
+	case BPF_JMP32 | BPF_JGT | BPF_K:
+	case BPF_JMP32 | BPF_JGE | BPF_K:
+	case BPF_JMP32 | BPF_JLT | BPF_K:
+	case BPF_JMP32 | BPF_JLE | BPF_K:
+	case BPF_JMP32 | BPF_JSGT | BPF_K:
+	case BPF_JMP32 | BPF_JSGE | BPF_K:
+	case BPF_JMP32 | BPF_JSLT | BPF_K:
+	case BPF_JMP32 | BPF_JSLE | BPF_K:
+		if (off == 0)
+			break;
+		setup_jmp_i(ctx, imm, 32, BPF_OP(code), off, &jmp, &rel);
+		if (valid_jmp_i(jmp, imm)) {
+			emit_jmp_i(ctx, lo(dst), imm, rel, jmp);
+		} else {
+			/* Move large immediate to register */
+			emit_mov_i(ctx, MIPS_R_T6, imm);
+			emit_jmp_r(ctx, lo(dst), MIPS_R_T6, rel, jmp);
+		}
+		if (finish_jmp(ctx, jmp, off) < 0)
+			goto toofar;
+		break;
+	/* PC += off if dst == src */
+	/* PC += off if dst != src */
+	/* PC += off if dst & src */
+	/* PC += off if dst > src */
+	/* PC += off if dst >= src */
+	/* PC += off if dst < src */
+	/* PC += off if dst <= src */
+	/* PC += off if dst > src (signed) */
+	/* PC += off if dst >= src (signed) */
+	/* PC += off if dst < src (signed) */
+	/* PC += off if dst <= src (signed) */
+	case BPF_JMP | BPF_JEQ | BPF_X:
+	case BPF_JMP | BPF_JNE | BPF_X:
+	case BPF_JMP | BPF_JSET | BPF_X:
+	case BPF_JMP | BPF_JGT | BPF_X:
+	case BPF_JMP | BPF_JGE | BPF_X:
+	case BPF_JMP | BPF_JLT | BPF_X:
+	case BPF_JMP | BPF_JLE | BPF_X:
+	case BPF_JMP | BPF_JSGT | BPF_X:
+	case BPF_JMP | BPF_JSGE | BPF_X:
+	case BPF_JMP | BPF_JSLT | BPF_X:
+	case BPF_JMP | BPF_JSLE | BPF_X:
+		if (off == 0)
+			break;
+		setup_jmp_r(ctx, dst == src, BPF_OP(code), off, &jmp, &rel);
+		emit_jmp_r64(ctx, dst, src, rel, jmp);
+		if (finish_jmp(ctx, jmp, off) < 0)
+			goto toofar;
+		break;
+	/* PC += off if dst == imm */
+	/* PC += off if dst != imm */
+	/* PC += off if dst & imm */
+	/* PC += off if dst > imm */
+	/* PC += off if dst >= imm */
+	/* PC += off if dst < imm */
+	/* PC += off if dst <= imm */
+	/* PC += off if dst > imm (signed) */
+	/* PC += off if dst >= imm (signed) */
+	/* PC += off if dst < imm (signed) */
+	/* PC += off if dst <= imm (signed) */
+	case BPF_JMP | BPF_JEQ | BPF_K:
+	case BPF_JMP | BPF_JNE | BPF_K:
+	case BPF_JMP | BPF_JSET | BPF_K:
+	case BPF_JMP | BPF_JGT | BPF_K:
+	case BPF_JMP | BPF_JGE | BPF_K:
+	case BPF_JMP | BPF_JLT | BPF_K:
+	case BPF_JMP | BPF_JLE | BPF_K:
+	case BPF_JMP | BPF_JSGT | BPF_K:
+	case BPF_JMP | BPF_JSGE | BPF_K:
+	case BPF_JMP | BPF_JSLT | BPF_K:
+	case BPF_JMP | BPF_JSLE | BPF_K:
+		if (off == 0)
+			break;
+		setup_jmp_i(ctx, imm, 64, BPF_OP(code), off, &jmp, &rel);
+		emit_jmp_i64(ctx, dst, imm, rel, jmp);
+		if (finish_jmp(ctx, jmp, off) < 0)
+			goto toofar;
+		break;
+	/* PC += off */
+	case BPF_JMP | BPF_JA:
+		if (off == 0)
+			break;
+		if (emit_ja(ctx, off) < 0)
+			goto toofar;
+		break;
+	/* Tail call */
+	case BPF_JMP | BPF_TAIL_CALL:
+		if (emit_tail_call(ctx) < 0)
+			goto invalid;
+		break;
+	/* Function call */
+	case BPF_JMP | BPF_CALL:
+		if (emit_call(ctx, insn) < 0)
+			goto invalid;
+		break;
+	/* Function return */
+	case BPF_JMP | BPF_EXIT:
+		/*
+		 * Optimization: when last instruction is EXIT
+		 * simply continue to epilogue.
+		 */
+		if (ctx->bpf_index == ctx->program->len - 1)
+			break;
+		if (emit_exit(ctx) < 0)
+			goto toofar;
+		break;
+
+	default:
+invalid:
+		pr_err_once("unknown opcode %02x\n", code);
+		return -EINVAL;
+notyet:
+		pr_info_once("*** NOT YET: opcode %02x ***\n", code);
+		return -EFAULT;
+toofar:
+		pr_info_once("*** TOO FAR: jump at %u opcode %02x ***\n",
+			     ctx->bpf_index, code);
+		return -E2BIG;
+	}
+	return 0;
+}
diff --git a/arch/mips/net/bpf_jit_comp64.c b/arch/mips/net/bpf_jit_comp64.c
new file mode 100644
index 000000000..0e7c1bdcf
--- /dev/null
+++ b/arch/mips/net/bpf_jit_comp64.c
@@ -0,0 +1,1068 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Just-In-Time compiler for eBPF bytecode on MIPS.
+ * Implementation of JIT functions for 64-bit CPUs.
+ *
+ * Copyright (c) 2021 Anyfi Networks AB.
+ * Author: Johan Almbladh <johan.almbladh@gmail.com>
+ *
+ * Based on code and ideas from
+ * Copyright (c) 2017 Cavium, Inc.
+ * Copyright (c) 2017 Shubham Bansal <illusionist.neo@gmail.com>
+ * Copyright (c) 2011 Mircea Gherzan <mgherzan@gmail.com>
+ */
+
+#include <linux/errno.h>
+#include <linux/filter.h>
+#include <linux/bpf.h>
+#include <asm/cpu-features.h>
+#include <asm/isa-rev.h>
+#include <asm/uasm.h>
+
+#include "bpf_jit_comp.h"
+
+/* MIPS t0-t3 are not available in the n64 ABI */
+#undef MIPS_R_T0
+#undef MIPS_R_T1
+#undef MIPS_R_T2
+#undef MIPS_R_T3
+
+/* Stack is 16-byte aligned in n64 ABI */
+#define MIPS_STACK_ALIGNMENT 16
+
+/* Extra 64-bit eBPF registers used by JIT */
+#define JIT_REG_TC (MAX_BPF_JIT_REG + 0)
+#define JIT_REG_ZX (MAX_BPF_JIT_REG + 1)
+
+/* Number of prologue bytes to skip when doing a tail call */
+#define JIT_TCALL_SKIP 4
+
+/* Callee-saved CPU registers that the JIT must preserve */
+#define JIT_CALLEE_REGS   \
+	(BIT(MIPS_R_S0) | \
+	 BIT(MIPS_R_S1) | \
+	 BIT(MIPS_R_S2) | \
+	 BIT(MIPS_R_S3) | \
+	 BIT(MIPS_R_S4) | \
+	 BIT(MIPS_R_S5) | \
+	 BIT(MIPS_R_S6) | \
+	 BIT(MIPS_R_S7) | \
+	 BIT(MIPS_R_GP) | \
+	 BIT(MIPS_R_FP) | \
+	 BIT(MIPS_R_RA))
+
+/* Caller-saved CPU registers available for JIT use */
+#define JIT_CALLER_REGS	  \
+	(BIT(MIPS_R_A5) | \
+	 BIT(MIPS_R_A6) | \
+	 BIT(MIPS_R_A7))
+/*
+ * Mapping of 64-bit eBPF registers to 64-bit native MIPS registers.
+ * MIPS registers t4 - t7 may be used by the JIT as temporary registers.
+ * MIPS registers t8 - t9 are reserved for single-register common functions.
+ */
+static const u8 bpf2mips64[] = {
+	/* Return value from in-kernel function, and exit value from eBPF */
+	[BPF_REG_0] = MIPS_R_V0,
+	/* Arguments from eBPF program to in-kernel function */
+	[BPF_REG_1] = MIPS_R_A0,
+	[BPF_REG_2] = MIPS_R_A1,
+	[BPF_REG_3] = MIPS_R_A2,
+	[BPF_REG_4] = MIPS_R_A3,
+	[BPF_REG_5] = MIPS_R_A4,
+	/* Callee-saved registers that in-kernel function will preserve */
+	[BPF_REG_6] = MIPS_R_S0,
+	[BPF_REG_7] = MIPS_R_S1,
+	[BPF_REG_8] = MIPS_R_S2,
+	[BPF_REG_9] = MIPS_R_S3,
+	/* Read-only frame pointer to access the eBPF stack */
+	[BPF_REG_FP] = MIPS_R_FP,
+	/* Temporary register for blinding constants */
+	[BPF_REG_AX] = MIPS_R_AT,
+	/* Tail call count register, caller-saved */
+	[JIT_REG_TC] = MIPS_R_A5,
+	/* Constant for register zero-extension */
+	[JIT_REG_ZX] = MIPS_R_V1,
+};
+
+/*
+ * MIPS 32-bit operations on 64-bit registers generate a sign-extended
+ * result. However, the eBPF ISA mandates zero-extension, so we rely on the
+ * verifier to add that for us (emit_zext_ver). In addition, ALU arithmetic
+ * operations, right shift and byte swap require properly sign-extended
+ * operands or the result is unpredictable. We emit explicit sign-extensions
+ * in those cases.
+ */
+
+/* Sign extension */
+static void emit_sext(struct jit_context *ctx, u8 dst, u8 src)
+{
+	emit(ctx, sll, dst, src, 0);
+	clobber_reg(ctx, dst);
+}
+
+/* Zero extension */
+static void emit_zext(struct jit_context *ctx, u8 dst)
+{
+	if (cpu_has_mips64r2 || cpu_has_mips64r6) {
+		emit(ctx, dinsu, dst, MIPS_R_ZERO, 32, 32);
+	} else {
+		emit(ctx, and, dst, dst, bpf2mips64[JIT_REG_ZX]);
+		access_reg(ctx, JIT_REG_ZX); /* We need the ZX register */
+	}
+	clobber_reg(ctx, dst);
+}
+
+/* Zero extension, if verifier does not do it for us  */
+static void emit_zext_ver(struct jit_context *ctx, u8 dst)
+{
+	if (!ctx->program->aux->verifier_zext)
+		emit_zext(ctx, dst);
+}
+
+/* dst = imm (64-bit) */
+static void emit_mov_i64(struct jit_context *ctx, u8 dst, u64 imm64)
+{
+	if (imm64 >= 0xffffffffffff8000ULL || imm64 < 0x8000ULL) {
+		emit(ctx, daddiu, dst, MIPS_R_ZERO, (s16)imm64);
+	} else if (imm64 >= 0xffffffff80000000ULL ||
+		   (imm64 < 0x80000000 && imm64 > 0xffff)) {
+		emit(ctx, lui, dst, (s16)(imm64 >> 16));
+		emit(ctx, ori, dst, dst, (u16)imm64 & 0xffff);
+	} else {
+		u8 acc = MIPS_R_ZERO;
+		int shift = 0;
+		int k;
+
+		for (k = 0; k < 4; k++) {
+			u16 half = imm64 >> (48 - 16 * k);
+
+			if (acc == dst)
+				shift += 16;
+
+			if (half) {
+				if (shift)
+					emit(ctx, dsll_safe, dst, dst, shift);
+				emit(ctx, ori, dst, acc, half);
+				acc = dst;
+				shift = 0;
+			}
+		}
+		if (shift)
+			emit(ctx, dsll_safe, dst, dst, shift);
+	}
+	clobber_reg(ctx, dst);
+}
+
+/* ALU immediate operation (64-bit) */
+static void emit_alu_i64(struct jit_context *ctx, u8 dst, s32 imm, u8 op)
+{
+	switch (BPF_OP(op)) {
+	/* dst = dst | imm */
+	case BPF_OR:
+		emit(ctx, ori, dst, dst, (u16)imm);
+		break;
+	/* dst = dst ^ imm */
+	case BPF_XOR:
+		emit(ctx, xori, dst, dst, (u16)imm);
+		break;
+	/* dst = -dst */
+	case BPF_NEG:
+		emit(ctx, dsubu, dst, MIPS_R_ZERO, dst);
+		break;
+	/* dst = dst << imm */
+	case BPF_LSH:
+		emit(ctx, dsll_safe, dst, dst, imm);
+		break;
+	/* dst = dst >> imm */
+	case BPF_RSH:
+		emit(ctx, dsrl_safe, dst, dst, imm);
+		break;
+	/* dst = dst >> imm (arithmetic) */
+	case BPF_ARSH:
+		emit(ctx, dsra_safe, dst, dst, imm);
+		break;
+	/* dst = dst + imm */
+	case BPF_ADD:
+		emit(ctx, daddiu, dst, dst, imm);
+		break;
+	/* dst = dst - imm */
+	case BPF_SUB:
+		emit(ctx, daddiu, dst, dst, -imm);
+		break;
+	default:
+		/* Width-generic operations */
+		emit_alu_i(ctx, dst, imm, op);
+	}
+	clobber_reg(ctx, dst);
+}
+
+/* ALU register operation (64-bit) */
+static void emit_alu_r64(struct jit_context *ctx, u8 dst, u8 src, u8 op)
+{
+	switch (BPF_OP(op)) {
+	/* dst = dst << src */
+	case BPF_LSH:
+		emit(ctx, dsllv, dst, dst, src);
+		break;
+	/* dst = dst >> src */
+	case BPF_RSH:
+		emit(ctx, dsrlv, dst, dst, src);
+		break;
+	/* dst = dst >> src (arithmetic) */
+	case BPF_ARSH:
+		emit(ctx, dsrav, dst, dst, src);
+		break;
+	/* dst = dst + src */
+	case BPF_ADD:
+		emit(ctx, daddu, dst, dst, src);
+		break;
+	/* dst = dst - src */
+	case BPF_SUB:
+		emit(ctx, dsubu, dst, dst, src);
+		break;
+	/* dst = dst * src */
+	case BPF_MUL:
+		if (cpu_has_mips64r6) {
+			emit(ctx, dmulu, dst, dst, src);
+		} else {
+			emit(ctx, dmultu, dst, src);
+			emit(ctx, mflo, dst);
+		}
+		break;
+	/* dst = dst / src */
+	case BPF_DIV:
+		if (cpu_has_mips64r6) {
+			emit(ctx, ddivu_r6, dst, dst, src);
+		} else {
+			emit(ctx, ddivu, dst, src);
+			emit(ctx, mflo, dst);
+		}
+		break;
+	/* dst = dst % src */
+	case BPF_MOD:
+		if (cpu_has_mips64r6) {
+			emit(ctx, dmodu, dst, dst, src);
+		} else {
+			emit(ctx, ddivu, dst, src);
+			emit(ctx, mfhi, dst);
+		}
+		break;
+	default:
+		/* Width-generic operations */
+		emit_alu_r(ctx, dst, src, op);
+	}
+	clobber_reg(ctx, dst);
+}
+
+/* Swap sub words in a register double word */
+static void emit_swap_r64(struct jit_context *ctx, u8 dst, u8 mask, u32 bits)
+{
+	u8 tmp = MIPS_R_T9;
+
+	emit(ctx, and, tmp, dst, mask);  /* tmp = dst & mask  */
+	emit(ctx, dsll, tmp, tmp, bits); /* tmp = tmp << bits */
+	emit(ctx, dsrl, dst, dst, bits); /* dst = dst >> bits */
+	emit(ctx, and, dst, dst, mask);  /* dst = dst & mask  */
+	emit(ctx, or, dst, dst, tmp);    /* dst = dst | tmp   */
+}
+
+/* Swap bytes and truncate a register double word, word or half word */
+static void emit_bswap_r64(struct jit_context *ctx, u8 dst, u32 width)
+{
+	switch (width) {
+	/* Swap bytes in a double word */
+	case 64:
+		if (cpu_has_mips64r2 || cpu_has_mips64r6) {
+			emit(ctx, dsbh, dst, dst);
+			emit(ctx, dshd, dst, dst);
+		} else {
+			u8 t1 = MIPS_R_T6;
+			u8 t2 = MIPS_R_T7;
+
+			emit(ctx, dsll32, t2, dst, 0);  /* t2 = dst << 32    */
+			emit(ctx, dsrl32, dst, dst, 0); /* dst = dst >> 32   */
+			emit(ctx, or, dst, dst, t2);    /* dst = dst | t2    */
+
+			emit(ctx, ori, t2, MIPS_R_ZERO, 0xffff);
+			emit(ctx, dsll32, t1, t2, 0);   /* t1 = t2 << 32     */
+			emit(ctx, or, t1, t1, t2);      /* t1 = t1 | t2      */
+			emit_swap_r64(ctx, dst, t1, 16);/* dst = swap16(dst) */
+
+			emit(ctx, lui, t2, 0xff);       /* t2 = 0x00ff0000   */
+			emit(ctx, ori, t2, t2, 0xff);   /* t2 = t2 | 0x00ff  */
+			emit(ctx, dsll32, t1, t2, 0);   /* t1 = t2 << 32     */
+			emit(ctx, or, t1, t1, t2);      /* t1 = t1 | t2      */
+			emit_swap_r64(ctx, dst, t1, 8); /* dst = swap8(dst)  */
+		}
+		break;
+	/* Swap bytes in a half word */
+	/* Swap bytes in a word */
+	case 32:
+	case 16:
+		emit_sext(ctx, dst, dst);
+		emit_bswap_r(ctx, dst, width);
+		if (cpu_has_mips64r2 || cpu_has_mips64r6)
+			emit_zext(ctx, dst);
+		break;
+	}
+	clobber_reg(ctx, dst);
+}
+
+/* Truncate a register double word, word or half word */
+static void emit_trunc_r64(struct jit_context *ctx, u8 dst, u32 width)
+{
+	switch (width) {
+	case 64:
+		break;
+	/* Zero-extend a word */
+	case 32:
+		emit_zext(ctx, dst);
+		break;
+	/* Zero-extend a half word */
+	case 16:
+		emit(ctx, andi, dst, dst, 0xffff);
+		break;
+	}
+	clobber_reg(ctx, dst);
+}
+
+/* Load operation: dst = *(size*)(src + off) */
+static void emit_ldx(struct jit_context *ctx, u8 dst, u8 src, s16 off, u8 size)
+{
+	switch (size) {
+	/* Load a byte */
+	case BPF_B:
+		emit(ctx, lbu, dst, off, src);
+		break;
+	/* Load a half word */
+	case BPF_H:
+		emit(ctx, lhu, dst, off, src);
+		break;
+	/* Load a word */
+	case BPF_W:
+		emit(ctx, lwu, dst, off, src);
+		break;
+	/* Load a double word */
+	case BPF_DW:
+		emit(ctx, ld, dst, off, src);
+		break;
+	}
+	clobber_reg(ctx, dst);
+}
+
+/* Store operation: *(size *)(dst + off) = src */
+static void emit_stx(struct jit_context *ctx, u8 dst, u8 src, s16 off, u8 size)
+{
+	switch (size) {
+	/* Store a byte */
+	case BPF_B:
+		emit(ctx, sb, src, off, dst);
+		break;
+	/* Store a half word */
+	case BPF_H:
+		emit(ctx, sh, src, off, dst);
+		break;
+	/* Store a word */
+	case BPF_W:
+		emit(ctx, sw, src, off, dst);
+		break;
+	/* Store a double word */
+	case BPF_DW:
+		emit(ctx, sd, src, off, dst);
+		break;
+	}
+}
+
+/* Atomic read-modify-write */
+static void emit_atomic_r64(struct jit_context *ctx,
+			    u8 dst, u8 src, s16 off, u8 code)
+{
+	u8 t1 = MIPS_R_T6;
+	u8 t2 = MIPS_R_T7;
+
+	LLSC_sync(ctx);
+	emit(ctx, lld, t1, off, dst);
+	switch (code) {
+	case BPF_ADD:
+	case BPF_ADD | BPF_FETCH:
+		emit(ctx, daddu, t2, t1, src);
+		break;
+	case BPF_AND:
+	case BPF_AND | BPF_FETCH:
+		emit(ctx, and, t2, t1, src);
+		break;
+	case BPF_OR:
+	case BPF_OR | BPF_FETCH:
+		emit(ctx, or, t2, t1, src);
+		break;
+	case BPF_XOR:
+	case BPF_XOR | BPF_FETCH:
+		emit(ctx, xor, t2, t1, src);
+		break;
+	case BPF_XCHG:
+		emit(ctx, move, t2, src);
+		break;
+	}
+	emit(ctx, scd, t2, off, dst);
+	emit(ctx, LLSC_beqz, t2, -16 - LLSC_offset);
+	emit(ctx, nop); /* Delay slot */
+
+	if (code & BPF_FETCH) {
+		emit(ctx, move, src, t1);
+		clobber_reg(ctx, src);
+	}
+}
+
+/* Atomic compare-and-exchange */
+static void emit_cmpxchg_r64(struct jit_context *ctx, u8 dst, u8 src, s16 off)
+{
+	u8 r0 = bpf2mips64[BPF_REG_0];
+	u8 t1 = MIPS_R_T6;
+	u8 t2 = MIPS_R_T7;
+
+	LLSC_sync(ctx);
+	emit(ctx, lld, t1, off, dst);
+	emit(ctx, bne, t1, r0, 12);
+	emit(ctx, move, t2, src);      /* Delay slot */
+	emit(ctx, scd, t2, off, dst);
+	emit(ctx, LLSC_beqz, t2, -20 - LLSC_offset);
+	emit(ctx, move, r0, t1);       /* Delay slot */
+
+	clobber_reg(ctx, r0);
+}
+
+/* Function call */
+static int emit_call(struct jit_context *ctx, const struct bpf_insn *insn)
+{
+	u8 zx = bpf2mips64[JIT_REG_ZX];
+	u8 tmp = MIPS_R_T6;
+	bool fixed;
+	u64 addr;
+
+	/* Decode the call address */
+	if (bpf_jit_get_func_addr(ctx->program, insn, false,
+				  &addr, &fixed) < 0)
+		return -1;
+	if (!fixed)
+		return -1;
+
+	/* Push caller-saved registers on stack */
+	push_regs(ctx, ctx->clobbered & JIT_CALLER_REGS, 0, 0);
+
+	/* Emit function call */
+	emit_mov_i64(ctx, tmp, addr & JALR_MASK);
+	emit(ctx, jalr, MIPS_R_RA, tmp);
+	emit(ctx, nop); /* Delay slot */
+
+	/* Restore caller-saved registers */
+	pop_regs(ctx, ctx->clobbered & JIT_CALLER_REGS, 0, 0);
+
+	/* Re-initialize the JIT zero-extension register if accessed */
+	if (ctx->accessed & BIT(JIT_REG_ZX)) {
+		emit(ctx, daddiu, zx, MIPS_R_ZERO, -1);
+		emit(ctx, dsrl32, zx, zx, 0);
+	}
+
+	clobber_reg(ctx, MIPS_R_RA);
+	clobber_reg(ctx, MIPS_R_V0);
+	clobber_reg(ctx, MIPS_R_V1);
+	return 0;
+}
+
+/* Function tail call */
+static int emit_tail_call(struct jit_context *ctx)
+{
+	u8 ary = bpf2mips64[BPF_REG_2];
+	u8 ind = bpf2mips64[BPF_REG_3];
+	u8 tcc = bpf2mips64[JIT_REG_TC];
+	u8 tmp = MIPS_R_T6;
+	int off;
+
+	/*
+	 * Tail call:
+	 * eBPF R1 - function argument (context ptr), passed in a0-a1
+	 * eBPF R2 - ptr to object with array of function entry points
+	 * eBPF R3 - array index of function to be called
+	 */
+
+	/* if (ind >= ary->map.max_entries) goto out */
+	off = offsetof(struct bpf_array, map.max_entries);
+	if (off > 0x7fff)
+		return -1;
+	emit(ctx, lwu, tmp, off, ary);            /* tmp = ary->map.max_entrs*/
+	emit(ctx, sltu, tmp, ind, tmp);           /* tmp = ind < t1          */
+	emit(ctx, beqz, tmp, get_offset(ctx, 1)); /* PC += off(1) if tmp == 0*/
+
+	/* if (--TCC < 0) goto out */
+	emit(ctx, daddiu, tcc, tcc, -1);          /* tcc-- (delay slot)      */
+	emit(ctx, bltz, tcc, get_offset(ctx, 1)); /* PC += off(1) if tcc < 0 */
+						  /* (next insn delay slot)  */
+	/* prog = ary->ptrs[ind] */
+	off = offsetof(struct bpf_array, ptrs);
+	if (off > 0x7fff)
+		return -1;
+	emit(ctx, dsll, tmp, ind, 3);             /* tmp = ind << 3          */
+	emit(ctx, daddu, tmp, tmp, ary);          /* tmp += ary              */
+	emit(ctx, ld, tmp, off, tmp);             /* tmp = *(tmp + off)      */
+
+	/* if (prog == 0) goto out */
+	emit(ctx, beqz, tmp, get_offset(ctx, 1)); /* PC += off(1) if tmp == 0*/
+	emit(ctx, nop);                           /* Delay slot              */
+
+	/* func = prog->bpf_func + 8 (prologue skip offset) */
+	off = offsetof(struct bpf_prog, bpf_func);
+	if (off > 0x7fff)
+		return -1;
+	emit(ctx, ld, tmp, off, tmp);                /* tmp = *(tmp + off)   */
+	emit(ctx, daddiu, tmp, tmp, JIT_TCALL_SKIP); /* tmp += skip (4)      */
+
+	/* goto func */
+	build_epilogue(ctx, tmp);
+	access_reg(ctx, JIT_REG_TC);
+	return 0;
+}
+
+/*
+ * Stack frame layout for a JITed program (stack grows down).
+ *
+ * Higher address  : Previous stack frame      :
+ *                 +===========================+  <--- MIPS sp before call
+ *                 | Callee-saved registers,   |
+ *                 | including RA and FP       |
+ *                 +---------------------------+  <--- eBPF FP (MIPS fp)
+ *                 | Local eBPF variables      |
+ *                 | allocated by program      |
+ *                 +---------------------------+
+ *                 | Reserved for caller-saved |
+ *                 | registers                 |
+ * Lower address   +===========================+  <--- MIPS sp
+ */
+
+/* Build program prologue to set up the stack and registers */
+void build_prologue(struct jit_context *ctx)
+{
+	u8 fp = bpf2mips64[BPF_REG_FP];
+	u8 tc = bpf2mips64[JIT_REG_TC];
+	u8 zx = bpf2mips64[JIT_REG_ZX];
+	int stack, saved, locals, reserved;
+
+	/*
+	 * In the unlikely event that the TCC limit is raised to more
+	 * than 16 bits, it is clamped to the maximum value allowed for
+	 * the generated code (0xffff). It is better fail to compile
+	 * instead of degrading gracefully.
+	 */
+	BUILD_BUG_ON(MAX_TAIL_CALL_CNT > 0xffff);
+
+	/*
+	 * The first instruction initializes the tail call count register.
+	 * On a tail call, the calling function jumps into the prologue
+	 * after this instruction.
+	 */
+	emit(ctx, ori, tc, MIPS_R_ZERO, MAX_TAIL_CALL_CNT);
+
+	/* === Entry-point for tail calls === */
+
+	/*
+	 * If the eBPF frame pointer and tail call count registers were
+	 * accessed they must be preserved. Mark them as clobbered here
+	 * to save and restore them on the stack as needed.
+	 */
+	if (ctx->accessed & BIT(BPF_REG_FP))
+		clobber_reg(ctx, fp);
+	if (ctx->accessed & BIT(JIT_REG_TC))
+		clobber_reg(ctx, tc);
+	if (ctx->accessed & BIT(JIT_REG_ZX))
+		clobber_reg(ctx, zx);
+
+	/* Compute the stack space needed for callee-saved registers */
+	saved = hweight32(ctx->clobbered & JIT_CALLEE_REGS) * sizeof(u64);
+	saved = ALIGN(saved, MIPS_STACK_ALIGNMENT);
+
+	/* Stack space used by eBPF program local data */
+	locals = ALIGN(ctx->program->aux->stack_depth, MIPS_STACK_ALIGNMENT);
+
+	/*
+	 * If we are emitting function calls, reserve extra stack space for
+	 * caller-saved registers needed by the JIT. The required space is
+	 * computed automatically during resource usage discovery (pass 1).
+	 */
+	reserved = ctx->stack_used;
+
+	/* Allocate the stack frame */
+	stack = ALIGN(saved + locals + reserved, MIPS_STACK_ALIGNMENT);
+	if (stack)
+		emit(ctx, daddiu, MIPS_R_SP, MIPS_R_SP, -stack);
+
+	/* Store callee-saved registers on stack */
+	push_regs(ctx, ctx->clobbered & JIT_CALLEE_REGS, 0, stack - saved);
+
+	/* Initialize the eBPF frame pointer if accessed */
+	if (ctx->accessed & BIT(BPF_REG_FP))
+		emit(ctx, daddiu, fp, MIPS_R_SP, stack - saved);
+
+	/* Initialize the ePF JIT zero-extension register if accessed */
+	if (ctx->accessed & BIT(JIT_REG_ZX)) {
+		emit(ctx, daddiu, zx, MIPS_R_ZERO, -1);
+		emit(ctx, dsrl32, zx, zx, 0);
+	}
+
+	ctx->saved_size = saved;
+	ctx->stack_size = stack;
+}
+
+/* Build the program epilogue to restore the stack and registers */
+void build_epilogue(struct jit_context *ctx, int dest_reg)
+{
+	/* Restore callee-saved registers from stack */
+	pop_regs(ctx, ctx->clobbered & JIT_CALLEE_REGS, 0,
+		 ctx->stack_size - ctx->saved_size);
+
+	/* Release the stack frame */
+	if (ctx->stack_size)
+		emit(ctx, daddiu, MIPS_R_SP, MIPS_R_SP, ctx->stack_size);
+
+	/* Jump to return address and sign-extend the 32-bit return value */
+	emit(ctx, jr, dest_reg);
+	emit(ctx, sll, MIPS_R_V0, MIPS_R_V0, 0); /* Delay slot */
+}
+
+/* Build one eBPF instruction */
+int build_insn(const struct bpf_insn *insn, struct jit_context *ctx)
+{
+	u8 dst = bpf2mips64[insn->dst_reg];
+	u8 src = bpf2mips64[insn->src_reg];
+	u8 res = bpf2mips64[BPF_REG_0];
+	u8 code = insn->code;
+	s16 off = insn->off;
+	s32 imm = insn->imm;
+	s32 val, rel;
+	u8 alu, jmp;
+
+	switch (code) {
+	/* ALU operations */
+	/* dst = imm */
+	case BPF_ALU | BPF_MOV | BPF_K:
+		emit_mov_i(ctx, dst, imm);
+		emit_zext_ver(ctx, dst);
+		break;
+	/* dst = src */
+	case BPF_ALU | BPF_MOV | BPF_X:
+		if (imm == 1) {
+			/* Special mov32 for zext */
+			emit_zext(ctx, dst);
+		} else {
+			emit_mov_r(ctx, dst, src);
+			emit_zext_ver(ctx, dst);
+		}
+		break;
+	/* dst = -dst */
+	case BPF_ALU | BPF_NEG:
+		emit_sext(ctx, dst, dst);
+		emit_alu_i(ctx, dst, 0, BPF_NEG);
+		emit_zext_ver(ctx, dst);
+		break;
+	/* dst = dst & imm */
+	/* dst = dst | imm */
+	/* dst = dst ^ imm */
+	/* dst = dst << imm */
+	case BPF_ALU | BPF_OR | BPF_K:
+	case BPF_ALU | BPF_AND | BPF_K:
+	case BPF_ALU | BPF_XOR | BPF_K:
+	case BPF_ALU | BPF_LSH | BPF_K:
+		if (!valid_alu_i(BPF_OP(code), imm)) {
+			emit_mov_i(ctx, MIPS_R_T4, imm);
+			emit_alu_r(ctx, dst, MIPS_R_T4, BPF_OP(code));
+		} else if (rewrite_alu_i(BPF_OP(code), imm, &alu, &val)) {
+			emit_alu_i(ctx, dst, val, alu);
+		}
+		emit_zext_ver(ctx, dst);
+		break;
+	/* dst = dst >> imm */
+	/* dst = dst >> imm (arithmetic) */
+	/* dst = dst + imm */
+	/* dst = dst - imm */
+	/* dst = dst * imm */
+	/* dst = dst / imm */
+	/* dst = dst % imm */
+	case BPF_ALU | BPF_RSH | BPF_K:
+	case BPF_ALU | BPF_ARSH | BPF_K:
+	case BPF_ALU | BPF_ADD | BPF_K:
+	case BPF_ALU | BPF_SUB | BPF_K:
+	case BPF_ALU | BPF_MUL | BPF_K:
+	case BPF_ALU | BPF_DIV | BPF_K:
+	case BPF_ALU | BPF_MOD | BPF_K:
+		if (!valid_alu_i(BPF_OP(code), imm)) {
+			emit_sext(ctx, dst, dst);
+			emit_mov_i(ctx, MIPS_R_T4, imm);
+			emit_alu_r(ctx, dst, MIPS_R_T4, BPF_OP(code));
+		} else if (rewrite_alu_i(BPF_OP(code), imm, &alu, &val)) {
+			emit_sext(ctx, dst, dst);
+			emit_alu_i(ctx, dst, val, alu);
+		}
+		emit_zext_ver(ctx, dst);
+		break;
+	/* dst = dst & src */
+	/* dst = dst | src */
+	/* dst = dst ^ src */
+	/* dst = dst << src */
+	case BPF_ALU | BPF_AND | BPF_X:
+	case BPF_ALU | BPF_OR | BPF_X:
+	case BPF_ALU | BPF_XOR | BPF_X:
+	case BPF_ALU | BPF_LSH | BPF_X:
+		emit_alu_r(ctx, dst, src, BPF_OP(code));
+		emit_zext_ver(ctx, dst);
+		break;
+	/* dst = dst >> src */
+	/* dst = dst >> src (arithmetic) */
+	/* dst = dst + src */
+	/* dst = dst - src */
+	/* dst = dst * src */
+	/* dst = dst / src */
+	/* dst = dst % src */
+	case BPF_ALU | BPF_RSH | BPF_X:
+	case BPF_ALU | BPF_ARSH | BPF_X:
+	case BPF_ALU | BPF_ADD | BPF_X:
+	case BPF_ALU | BPF_SUB | BPF_X:
+	case BPF_ALU | BPF_MUL | BPF_X:
+	case BPF_ALU | BPF_DIV | BPF_X:
+	case BPF_ALU | BPF_MOD | BPF_X:
+		emit_sext(ctx, dst, dst);
+		emit_sext(ctx, MIPS_R_T4, src);
+		emit_alu_r(ctx, dst, MIPS_R_T4, BPF_OP(code));
+		emit_zext_ver(ctx, dst);
+		break;
+	/* dst = imm (64-bit) */
+	case BPF_ALU64 | BPF_MOV | BPF_K:
+		emit_mov_i(ctx, dst, imm);
+		break;
+	/* dst = src (64-bit) */
+	case BPF_ALU64 | BPF_MOV | BPF_X:
+		emit_mov_r(ctx, dst, src);
+		break;
+	/* dst = -dst (64-bit) */
+	case BPF_ALU64 | BPF_NEG:
+		emit_alu_i64(ctx, dst, 0, BPF_NEG);
+		break;
+	/* dst = dst & imm (64-bit) */
+	/* dst = dst | imm (64-bit) */
+	/* dst = dst ^ imm (64-bit) */
+	/* dst = dst << imm (64-bit) */
+	/* dst = dst >> imm (64-bit) */
+	/* dst = dst >> imm ((64-bit, arithmetic) */
+	/* dst = dst + imm (64-bit) */
+	/* dst = dst - imm (64-bit) */
+	/* dst = dst * imm (64-bit) */
+	/* dst = dst / imm (64-bit) */
+	/* dst = dst % imm (64-bit) */
+	case BPF_ALU64 | BPF_AND | BPF_K:
+	case BPF_ALU64 | BPF_OR | BPF_K:
+	case BPF_ALU64 | BPF_XOR | BPF_K:
+	case BPF_ALU64 | BPF_LSH | BPF_K:
+	case BPF_ALU64 | BPF_RSH | BPF_K:
+	case BPF_ALU64 | BPF_ARSH | BPF_K:
+	case BPF_ALU64 | BPF_ADD | BPF_K:
+	case BPF_ALU64 | BPF_SUB | BPF_K:
+	case BPF_ALU64 | BPF_MUL | BPF_K:
+	case BPF_ALU64 | BPF_DIV | BPF_K:
+	case BPF_ALU64 | BPF_MOD | BPF_K:
+		if (!valid_alu_i(BPF_OP(code), imm)) {
+			emit_mov_i(ctx, MIPS_R_T4, imm);
+			emit_alu_r64(ctx, dst, MIPS_R_T4, BPF_OP(code));
+		} else if (rewrite_alu_i(BPF_OP(code), imm, &alu, &val)) {
+			emit_alu_i64(ctx, dst, val, alu);
+		}
+		break;
+	/* dst = dst & src (64-bit) */
+	/* dst = dst | src (64-bit) */
+	/* dst = dst ^ src (64-bit) */
+	/* dst = dst << src (64-bit) */
+	/* dst = dst >> src (64-bit) */
+	/* dst = dst >> src (64-bit, arithmetic) */
+	/* dst = dst + src (64-bit) */
+	/* dst = dst - src (64-bit) */
+	/* dst = dst * src (64-bit) */
+	/* dst = dst / src (64-bit) */
+	/* dst = dst % src (64-bit) */
+	case BPF_ALU64 | BPF_AND | BPF_X:
+	case BPF_ALU64 | BPF_OR | BPF_X:
+	case BPF_ALU64 | BPF_XOR | BPF_X:
+	case BPF_ALU64 | BPF_LSH | BPF_X:
+	case BPF_ALU64 | BPF_RSH | BPF_X:
+	case BPF_ALU64 | BPF_ARSH | BPF_X:
+	case BPF_ALU64 | BPF_ADD | BPF_X:
+	case BPF_ALU64 | BPF_SUB | BPF_X:
+	case BPF_ALU64 | BPF_MUL | BPF_X:
+	case BPF_ALU64 | BPF_DIV | BPF_X:
+	case BPF_ALU64 | BPF_MOD | BPF_X:
+		emit_alu_r64(ctx, dst, src, BPF_OP(code));
+		break;
+	/* dst = htole(dst) */
+	/* dst = htobe(dst) */
+	case BPF_ALU | BPF_END | BPF_FROM_LE:
+	case BPF_ALU | BPF_END | BPF_FROM_BE:
+		if (BPF_SRC(code) ==
+#ifdef __BIG_ENDIAN
+		    BPF_FROM_LE
+#else
+		    BPF_FROM_BE
+#endif
+		    )
+			emit_bswap_r64(ctx, dst, imm);
+		else
+			emit_trunc_r64(ctx, dst, imm);
+		break;
+	/* dst = imm64 */
+	case BPF_LD | BPF_IMM | BPF_DW:
+		emit_mov_i64(ctx, dst, (u32)imm | ((u64)insn[1].imm << 32));
+		return 1;
+	/* LDX: dst = *(size *)(src + off) */
+	case BPF_LDX | BPF_MEM | BPF_W:
+	case BPF_LDX | BPF_MEM | BPF_H:
+	case BPF_LDX | BPF_MEM | BPF_B:
+	case BPF_LDX | BPF_MEM | BPF_DW:
+		emit_ldx(ctx, dst, src, off, BPF_SIZE(code));
+		break;
+	/* ST: *(size *)(dst + off) = imm */
+	case BPF_ST | BPF_MEM | BPF_W:
+	case BPF_ST | BPF_MEM | BPF_H:
+	case BPF_ST | BPF_MEM | BPF_B:
+	case BPF_ST | BPF_MEM | BPF_DW:
+		emit_mov_i(ctx, MIPS_R_T4, imm);
+		emit_stx(ctx, dst, MIPS_R_T4, off, BPF_SIZE(code));
+		break;
+	/* STX: *(size *)(dst + off) = src */
+	case BPF_STX | BPF_MEM | BPF_W:
+	case BPF_STX | BPF_MEM | BPF_H:
+	case BPF_STX | BPF_MEM | BPF_B:
+	case BPF_STX | BPF_MEM | BPF_DW:
+		emit_stx(ctx, dst, src, off, BPF_SIZE(code));
+		break;
+	/* Speculation barrier */
+	case BPF_ST | BPF_NOSPEC:
+		break;
+	/* Atomics */
+	case BPF_STX | BPF_ATOMIC | BPF_W:
+	case BPF_STX | BPF_ATOMIC | BPF_DW:
+		switch (imm) {
+		case BPF_ADD:
+		case BPF_ADD | BPF_FETCH:
+		case BPF_AND:
+		case BPF_AND | BPF_FETCH:
+		case BPF_OR:
+		case BPF_OR | BPF_FETCH:
+		case BPF_XOR:
+		case BPF_XOR | BPF_FETCH:
+		case BPF_XCHG:
+			if (BPF_SIZE(code) == BPF_DW) {
+				emit_atomic_r64(ctx, dst, src, off, imm);
+			} else if (imm & BPF_FETCH) {
+				u8 tmp = dst;
+
+				if (src == dst) { /* Don't overwrite dst */
+					emit_mov_r(ctx, MIPS_R_T4, dst);
+					tmp = MIPS_R_T4;
+				}
+				emit_sext(ctx, src, src);
+				emit_atomic_r(ctx, tmp, src, off, imm);
+				emit_zext_ver(ctx, src);
+			} else { /* 32-bit, no fetch */
+				emit_sext(ctx, MIPS_R_T4, src);
+				emit_atomic_r(ctx, dst, MIPS_R_T4, off, imm);
+			}
+			break;
+		case BPF_CMPXCHG:
+			if (BPF_SIZE(code) == BPF_DW) {
+				emit_cmpxchg_r64(ctx, dst, src, off);
+			} else {
+				u8 tmp = res;
+
+				if (res == dst)   /* Don't overwrite dst */
+					tmp = MIPS_R_T4;
+				emit_sext(ctx, tmp, res);
+				emit_sext(ctx, MIPS_R_T5, src);
+				emit_cmpxchg_r(ctx, dst, MIPS_R_T5, tmp, off);
+				if (res == dst)   /* Restore result */
+					emit_mov_r(ctx, res, MIPS_R_T4);
+				/* Result zext inserted by verifier */
+			}
+			break;
+		default:
+			goto notyet;
+		}
+		break;
+	/* PC += off if dst == src */
+	/* PC += off if dst != src */
+	/* PC += off if dst & src */
+	/* PC += off if dst > src */
+	/* PC += off if dst >= src */
+	/* PC += off if dst < src */
+	/* PC += off if dst <= src */
+	/* PC += off if dst > src (signed) */
+	/* PC += off if dst >= src (signed) */
+	/* PC += off if dst < src (signed) */
+	/* PC += off if dst <= src (signed) */
+	case BPF_JMP32 | BPF_JEQ | BPF_X:
+	case BPF_JMP32 | BPF_JNE | BPF_X:
+	case BPF_JMP32 | BPF_JSET | BPF_X:
+	case BPF_JMP32 | BPF_JGT | BPF_X:
+	case BPF_JMP32 | BPF_JGE | BPF_X:
+	case BPF_JMP32 | BPF_JLT | BPF_X:
+	case BPF_JMP32 | BPF_JLE | BPF_X:
+	case BPF_JMP32 | BPF_JSGT | BPF_X:
+	case BPF_JMP32 | BPF_JSGE | BPF_X:
+	case BPF_JMP32 | BPF_JSLT | BPF_X:
+	case BPF_JMP32 | BPF_JSLE | BPF_X:
+		if (off == 0)
+			break;
+		setup_jmp_r(ctx, dst == src, BPF_OP(code), off, &jmp, &rel);
+		emit_sext(ctx, MIPS_R_T4, dst); /* Sign-extended dst */
+		emit_sext(ctx, MIPS_R_T5, src); /* Sign-extended src */
+		emit_jmp_r(ctx, MIPS_R_T4, MIPS_R_T5, rel, jmp);
+		if (finish_jmp(ctx, jmp, off) < 0)
+			goto toofar;
+		break;
+	/* PC += off if dst == imm */
+	/* PC += off if dst != imm */
+	/* PC += off if dst & imm */
+	/* PC += off if dst > imm */
+	/* PC += off if dst >= imm */
+	/* PC += off if dst < imm */
+	/* PC += off if dst <= imm */
+	/* PC += off if dst > imm (signed) */
+	/* PC += off if dst >= imm (signed) */
+	/* PC += off if dst < imm (signed) */
+	/* PC += off if dst <= imm (signed) */
+	case BPF_JMP32 | BPF_JEQ | BPF_K:
+	case BPF_JMP32 | BPF_JNE | BPF_K:
+	case BPF_JMP32 | BPF_JSET | BPF_K:
+	case BPF_JMP32 | BPF_JGT | BPF_K:
+	case BPF_JMP32 | BPF_JGE | BPF_K:
+	case BPF_JMP32 | BPF_JLT | BPF_K:
+	case BPF_JMP32 | BPF_JLE | BPF_K:
+	case BPF_JMP32 | BPF_JSGT | BPF_K:
+	case BPF_JMP32 | BPF_JSGE | BPF_K:
+	case BPF_JMP32 | BPF_JSLT | BPF_K:
+	case BPF_JMP32 | BPF_JSLE | BPF_K:
+		if (off == 0)
+			break;
+		setup_jmp_i(ctx, imm, 32, BPF_OP(code), off, &jmp, &rel);
+		emit_sext(ctx, MIPS_R_T4, dst); /* Sign-extended dst */
+		if (valid_jmp_i(jmp, imm)) {
+			emit_jmp_i(ctx, MIPS_R_T4, imm, rel, jmp);
+		} else {
+			/* Move large immediate to register, sign-extended */
+			emit_mov_i(ctx, MIPS_R_T5, imm);
+			emit_jmp_r(ctx, MIPS_R_T4, MIPS_R_T5, rel, jmp);
+		}
+		if (finish_jmp(ctx, jmp, off) < 0)
+			goto toofar;
+		break;
+	/* PC += off if dst == src */
+	/* PC += off if dst != src */
+	/* PC += off if dst & src */
+	/* PC += off if dst > src */
+	/* PC += off if dst >= src */
+	/* PC += off if dst < src */
+	/* PC += off if dst <= src */
+	/* PC += off if dst > src (signed) */
+	/* PC += off if dst >= src (signed) */
+	/* PC += off if dst < src (signed) */
+	/* PC += off if dst <= src (signed) */
+	case BPF_JMP | BPF_JEQ | BPF_X:
+	case BPF_JMP | BPF_JNE | BPF_X:
+	case BPF_JMP | BPF_JSET | BPF_X:
+	case BPF_JMP | BPF_JGT | BPF_X:
+	case BPF_JMP | BPF_JGE | BPF_X:
+	case BPF_JMP | BPF_JLT | BPF_X:
+	case BPF_JMP | BPF_JLE | BPF_X:
+	case BPF_JMP | BPF_JSGT | BPF_X:
+	case BPF_JMP | BPF_JSGE | BPF_X:
+	case BPF_JMP | BPF_JSLT | BPF_X:
+	case BPF_JMP | BPF_JSLE | BPF_X:
+		if (off == 0)
+			break;
+		setup_jmp_r(ctx, dst == src, BPF_OP(code), off, &jmp, &rel);
+		emit_jmp_r(ctx, dst, src, rel, jmp);
+		if (finish_jmp(ctx, jmp, off) < 0)
+			goto toofar;
+		break;
+	/* PC += off if dst == imm */
+	/* PC += off if dst != imm */
+	/* PC += off if dst & imm */
+	/* PC += off if dst > imm */
+	/* PC += off if dst >= imm */
+	/* PC += off if dst < imm */
+	/* PC += off if dst <= imm */
+	/* PC += off if dst > imm (signed) */
+	/* PC += off if dst >= imm (signed) */
+	/* PC += off if dst < imm (signed) */
+	/* PC += off if dst <= imm (signed) */
+	case BPF_JMP | BPF_JEQ | BPF_K:
+	case BPF_JMP | BPF_JNE | BPF_K:
+	case BPF_JMP | BPF_JSET | BPF_K:
+	case BPF_JMP | BPF_JGT | BPF_K:
+	case BPF_JMP | BPF_JGE | BPF_K:
+	case BPF_JMP | BPF_JLT | BPF_K:
+	case BPF_JMP | BPF_JLE | BPF_K:
+	case BPF_JMP | BPF_JSGT | BPF_K:
+	case BPF_JMP | BPF_JSGE | BPF_K:
+	case BPF_JMP | BPF_JSLT | BPF_K:
+	case BPF_JMP | BPF_JSLE | BPF_K:
+		if (off == 0)
+			break;
+		setup_jmp_i(ctx, imm, 64, BPF_OP(code), off, &jmp, &rel);
+		if (valid_jmp_i(jmp, imm)) {
+			emit_jmp_i(ctx, dst, imm, rel, jmp);
+		} else {
+			/* Move large immediate to register */
+			emit_mov_i(ctx, MIPS_R_T4, imm);
+			emit_jmp_r(ctx, dst, MIPS_R_T4, rel, jmp);
+		}
+		if (finish_jmp(ctx, jmp, off) < 0)
+			goto toofar;
+		break;
+	/* PC += off */
+	case BPF_JMP | BPF_JA:
+		if (off == 0)
+			break;
+		if (emit_ja(ctx, off) < 0)
+			goto toofar;
+		break;
+	/* Tail call */
+	case BPF_JMP | BPF_TAIL_CALL:
+		if (emit_tail_call(ctx) < 0)
+			goto invalid;
+		break;
+	/* Function call */
+	case BPF_JMP | BPF_CALL:
+		if (emit_call(ctx, insn) < 0)
+			goto invalid;
+		break;
+	/* Function return */
+	case BPF_JMP | BPF_EXIT:
+		/*
+		 * Optimization: when last instruction is EXIT
+		 * simply continue to epilogue.
+		 */
+		if (ctx->bpf_index == ctx->program->len - 1)
+			break;
+		if (emit_exit(ctx) < 0)
+			goto toofar;
+		break;
+
+	default:
+invalid:
+		pr_err_once("unknown opcode %02x\n", code);
+		return -EINVAL;
+notyet:
+		pr_info_once("*** NOT YET: opcode %02x ***\n", code);
+		return -EFAULT;
+toofar:
+		pr_info_once("*** TOO FAR: jump at %u opcode %02x ***\n",
+			     ctx->bpf_index, code);
+		return -E2BIG;
+	}
+	return 0;
+}
diff --git a/arch/mips/pci/Makefile b/arch/mips/pci/Makefile
new file mode 100644
index 000000000..a6e9785b5
--- /dev/null
+++ b/arch/mips/pci/Makefile
@@ -0,0 +1,52 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Makefile for the PCI specific kernel interface routines under Linux.
+#
+
+obj-y				+= pci.o
+obj-$(CONFIG_PCI_DRIVERS_LEGACY)+= pci-legacy.o
+obj-$(CONFIG_PCI_DRIVERS_GENERIC)+= pci-generic.o
+
+#
+# PCI bus host bridge specific code
+#
+obj-$(CONFIG_MIPS_BONITO64)	+= ops-bonito64.o
+obj-$(CONFIG_PCI_GT64XXX_PCI0)	+= ops-gt64xxx_pci0.o
+obj-$(CONFIG_MIPS_MSC)		+= ops-msc.o
+obj-$(CONFIG_PCI_TX4927)	+= ops-tx4927.o
+obj-$(CONFIG_BCM47XX)		+= pci-bcm47xx.o
+obj-$(CONFIG_BCM63XX)		+= pci-bcm63xx.o fixup-bcm63xx.o \
+					ops-bcm63xx.o
+obj-$(CONFIG_MIPS_ALCHEMY)	+= pci-alchemy.o
+obj-$(CONFIG_PCI_AR2315)	+= pci-ar2315.o
+obj-$(CONFIG_SOC_AR71XX)	+= pci-ar71xx.o
+obj-$(CONFIG_PCI_AR724X)	+= pci-ar724x.o
+obj-$(CONFIG_PCI_XTALK_BRIDGE)	+= pci-xtalk-bridge.o
+#
+# These are still pretty much in the old state, watch, go blind.
+#
+obj-$(CONFIG_ATH79)		+= fixup-ath79.o
+obj-$(CONFIG_MIPS_COBALT)	+= fixup-cobalt.o
+obj-$(CONFIG_LEMOTE_FULOONG2E)	+= fixup-fuloong2e.o ops-loongson2.o
+obj-$(CONFIG_LEMOTE_MACH2F)	+= fixup-lemote2f.o ops-loongson2.o
+obj-$(CONFIG_MIPS_MALTA)	+= fixup-malta.o pci-malta.o
+obj-$(CONFIG_SGI_IP27)		+= pci-ip27.o
+obj-$(CONFIG_SGI_IP32)		+= fixup-ip32.o ops-mace.o pci-ip32.o
+obj-$(CONFIG_SIBYTE_SB1250)	+= fixup-sb1250.o pci-sb1250.o
+obj-$(CONFIG_SIBYTE_BCM112X)	+= fixup-sb1250.o pci-sb1250.o
+obj-$(CONFIG_SIBYTE_BCM1x80)	+= pci-bcm1480.o pci-bcm1480ht.o
+obj-$(CONFIG_SNI_RM)		+= fixup-sni.o ops-sni.o
+obj-$(CONFIG_LANTIQ)		+= fixup-lantiq.o
+obj-$(CONFIG_PCI_LANTIQ)	+= pci-lantiq.o ops-lantiq.o
+obj-$(CONFIG_SOC_MT7620)	+= pci-mt7620.o
+obj-$(CONFIG_SOC_RT288X)	+= pci-rt2880.o
+obj-$(CONFIG_SOC_RT3883)	+= pci-rt3883.o
+obj-$(CONFIG_SOC_TX4927)	+= pci-tx4927.o
+obj-$(CONFIG_SOC_TX4938)	+= pci-tx4938.o
+obj-$(CONFIG_TOSHIBA_RBTX4927)	+= fixup-rbtx4927.o
+obj-$(CONFIG_MIKROTIK_RB532)	+= pci-rc32434.o ops-rc32434.o fixup-rc32434.o
+obj-$(CONFIG_CAVIUM_OCTEON_SOC) += pci-octeon.o pcie-octeon.o
+
+ifdef CONFIG_PCI_MSI
+obj-$(CONFIG_CAVIUM_OCTEON_SOC) += msi-octeon.o
+endif
diff --git a/arch/mips/pci/fixup-ath79.c b/arch/mips/pci/fixup-ath79.c
new file mode 100644
index 000000000..09a4ce534
--- /dev/null
+++ b/arch/mips/pci/fixup-ath79.c
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *  Copyright (C) 2018 John Crispin <john@phrozen.org>
+ */
+
+#include <linux/pci.h>
+//#include <linux/of_irq.h>
+#include <linux/of_pci.h>
+
+int pcibios_plat_dev_init(struct pci_dev *dev)
+{
+	return PCIBIOS_SUCCESSFUL;
+}
+
+int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	return of_irq_parse_and_map_pci(dev, slot, pin);
+}
diff --git a/arch/mips/pci/fixup-bcm63xx.c b/arch/mips/pci/fixup-bcm63xx.c
new file mode 100644
index 000000000..340863009
--- /dev/null
+++ b/arch/mips/pci/fixup-bcm63xx.c
@@ -0,0 +1,21 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ */
+
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <bcm63xx_cpu.h>
+
+int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	return bcm63xx_get_irq_number(IRQ_PCI);
+}
+
+int pcibios_plat_dev_init(struct pci_dev *dev)
+{
+	return 0;
+}
diff --git a/arch/mips/pci/fixup-cobalt.c b/arch/mips/pci/fixup-cobalt.c
new file mode 100644
index 000000000..00206ff52
--- /dev/null
+++ b/arch/mips/pci/fixup-cobalt.c
@@ -0,0 +1,207 @@
+/*
+ * Cobalt Qube/Raq PCI support
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1995, 1996, 1997, 2002, 2003 by Ralf Baechle
+ * Copyright (C) 2001, 2002, 2003 by Liam Davies (ldavies@agile.tv)
+ */
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+
+#include <asm/io.h>
+#include <asm/gt64120.h>
+
+#include <cobalt.h>
+#include <irq.h>
+
+/*
+ * PCI slot numbers
+ */
+#define COBALT_PCICONF_CPU	0x06
+#define COBALT_PCICONF_ETH0	0x07
+#define COBALT_PCICONF_RAQSCSI	0x08
+#define COBALT_PCICONF_VIA	0x09
+#define COBALT_PCICONF_PCISLOT	0x0A
+#define COBALT_PCICONF_ETH1	0x0C
+
+/*
+ * The Cobalt board ID information.  The boards have an ID number wired
+ * into the VIA that is available in the high nibble of register 94.
+ */
+#define VIA_COBALT_BRD_ID_REG  0x94
+#define VIA_COBALT_BRD_REG_to_ID(reg)	((unsigned char)(reg) >> 4)
+
+/*
+ * Default value of PCI Class Code on GT64111 is PCI_CLASS_MEMORY_OTHER (0x0580)
+ * instead of PCI_CLASS_BRIDGE_HOST (0x0600). Galileo explained this choice in
+ * document "GT-64111 System Controller for RC4640, RM523X and VR4300 CPUs",
+ * section "6.5.3 PCI Autoconfiguration at RESET":
+ *
+ *   Some PCs refuse to configure host bridges if they are found plugged into
+ *   a PCI slot (ask the BIOS vendors why...). The "Memory Controller" Class
+ *   Code does not cause a problem for these non-compliant BIOSes, so we used
+ *   this as the default in the GT-64111.
+ *
+ * So fix the incorrect default value of PCI Class Code. More details are on:
+ * https://lore.kernel.org/r/20211102154831.xtrlgrmrizl5eidl@pali/
+ * https://lore.kernel.org/r/20211102150201.GA11675@alpha.franken.de/
+ */
+static void qube_raq_galileo_early_fixup(struct pci_dev *dev)
+{
+	if (dev->devfn == PCI_DEVFN(0, 0) &&
+		(dev->class >> 8) == PCI_CLASS_MEMORY_OTHER) {
+
+		dev->class = (PCI_CLASS_BRIDGE_HOST << 8) | (dev->class & 0xff);
+
+		printk(KERN_INFO "Galileo: fixed bridge class\n");
+	}
+}
+
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_MARVELL, PCI_DEVICE_ID_MARVELL_GT64111,
+	 qube_raq_galileo_early_fixup);
+
+static void qube_raq_via_bmIDE_fixup(struct pci_dev *dev)
+{
+	unsigned short cfgword;
+	unsigned char lt;
+
+	/* Enable Bus Mastering and fast back to back. */
+	pci_read_config_word(dev, PCI_COMMAND, &cfgword);
+	cfgword |= (PCI_COMMAND_FAST_BACK | PCI_COMMAND_MASTER);
+	pci_write_config_word(dev, PCI_COMMAND, cfgword);
+
+	/* Enable both ide interfaces. ROM only enables primary one.  */
+	pci_write_config_byte(dev, 0x40, 0xb);
+
+	/* Set latency timer to reasonable value. */
+	pci_read_config_byte(dev, PCI_LATENCY_TIMER, &lt);
+	if (lt < 64)
+		pci_write_config_byte(dev, PCI_LATENCY_TIMER, 64);
+	pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, 8);
+}
+
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_1,
+	 qube_raq_via_bmIDE_fixup);
+
+static void qube_raq_galileo_fixup(struct pci_dev *dev)
+{
+	if (dev->devfn != PCI_DEVFN(0, 0))
+		return;
+
+	/* Fix PCI latency-timer and cache-line-size values in Galileo
+	 * host bridge.
+	 */
+	pci_write_config_byte(dev, PCI_LATENCY_TIMER, 64);
+	pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, 8);
+
+	/*
+	 * The code described by the comment below has been removed
+	 * as it causes bus mastering by the Ethernet controllers
+	 * to break under any kind of network load. We always set
+	 * the retry timeouts to their maximum.
+	 *
+	 * --x--x--x--x--x--x--x--x--x--x--x--x--x--x--x--x--x--x--x--x--
+	 *
+	 * On all machines prior to Q2, we had the STOP line disconnected
+	 * from Galileo to VIA on PCI.	The new Galileo does not function
+	 * correctly unless we have it connected.
+	 *
+	 * Therefore we must set the disconnect/retry cycle values to
+	 * something sensible when using the new Galileo.
+	 */
+
+	printk(KERN_INFO "Galileo: revision %u\n", dev->revision);
+
+#if 0
+	if (dev->revision >= 0x10) {
+		/* New Galileo, assumes PCI stop line to VIA is connected. */
+		GT_WRITE(GT_PCI0_TOR_OFS, 0x4020);
+	} else if (dev->revision == 0x1 || dev->revision == 0x2)
+#endif
+	{
+		signed int timeo;
+		/* XXX WE MUST DO THIS ELSE GALILEO LOCKS UP! -DaveM */
+		timeo = GT_READ(GT_PCI0_TOR_OFS);
+		/* Old Galileo, assumes PCI STOP line to VIA is disconnected. */
+		GT_WRITE(GT_PCI0_TOR_OFS,
+			(0xff << 16) |		/* retry count */
+			(0xff << 8) |		/* timeout 1   */
+			0xff);			/* timeout 0   */
+
+		/* enable PCI retry exceeded interrupt */
+		GT_WRITE(GT_INTRMASK_OFS, GT_INTR_RETRYCTR0_MSK | GT_READ(GT_INTRMASK_OFS));
+	}
+}
+
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL, PCI_DEVICE_ID_MARVELL_GT64111,
+	 qube_raq_galileo_fixup);
+
+int cobalt_board_id;
+
+static void qube_raq_via_board_id_fixup(struct pci_dev *dev)
+{
+	u8 id;
+	int retval;
+
+	retval = pci_read_config_byte(dev, VIA_COBALT_BRD_ID_REG, &id);
+	if (retval) {
+		panic("Cannot read board ID");
+		return;
+	}
+
+	cobalt_board_id = VIA_COBALT_BRD_REG_to_ID(id);
+
+	printk(KERN_INFO "Cobalt board ID: %d\n", cobalt_board_id);
+}
+
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_0,
+	 qube_raq_via_board_id_fixup);
+
+static char irq_tab_qube1[] = {
+  [COBALT_PCICONF_CPU]	   = 0,
+  [COBALT_PCICONF_ETH0]	   = QUBE1_ETH0_IRQ,
+  [COBALT_PCICONF_RAQSCSI] = SCSI_IRQ,
+  [COBALT_PCICONF_VIA]	   = 0,
+  [COBALT_PCICONF_PCISLOT] = PCISLOT_IRQ,
+  [COBALT_PCICONF_ETH1]	   = 0
+};
+
+static char irq_tab_cobalt[] = {
+  [COBALT_PCICONF_CPU]	   = 0,
+  [COBALT_PCICONF_ETH0]	   = ETH0_IRQ,
+  [COBALT_PCICONF_RAQSCSI] = SCSI_IRQ,
+  [COBALT_PCICONF_VIA]	   = 0,
+  [COBALT_PCICONF_PCISLOT] = PCISLOT_IRQ,
+  [COBALT_PCICONF_ETH1]	   = ETH1_IRQ
+};
+
+static char irq_tab_raq2[] = {
+  [COBALT_PCICONF_CPU]	   = 0,
+  [COBALT_PCICONF_ETH0]	   = ETH0_IRQ,
+  [COBALT_PCICONF_RAQSCSI] = RAQ2_SCSI_IRQ,
+  [COBALT_PCICONF_VIA]	   = 0,
+  [COBALT_PCICONF_PCISLOT] = PCISLOT_IRQ,
+  [COBALT_PCICONF_ETH1]	   = ETH1_IRQ
+};
+
+int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	if (cobalt_board_id <= COBALT_BRD_ID_QUBE1)
+		return irq_tab_qube1[slot];
+
+	if (cobalt_board_id == COBALT_BRD_ID_RAQ2)
+		return irq_tab_raq2[slot];
+
+	return irq_tab_cobalt[slot];
+}
+
+/* Do platform specific device initialization at pci_enable_device() time */
+int pcibios_plat_dev_init(struct pci_dev *dev)
+{
+	return 0;
+}
diff --git a/arch/mips/pci/fixup-fuloong2e.c b/arch/mips/pci/fixup-fuloong2e.c
new file mode 100644
index 000000000..91aa92323
--- /dev/null
+++ b/arch/mips/pci/fixup-fuloong2e.c
@@ -0,0 +1,221 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2004 ICT CAS
+ * Author: Li xiaoyu, ICT CAS
+ *   lixy@ict.ac.cn
+ *
+ * Copyright (C) 2007 Lemote, Inc. & Institute of Computing Technology
+ * Author: Fuxin Zhang, zhangfx@lemote.com
+ */
+#include <linux/init.h>
+#include <linux/pci.h>
+
+#include <loongson.h>
+
+/* South bridge slot number is set by the pci probe process */
+static u8 sb_slot = 5;
+
+int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	int irq = 0;
+
+	if (slot == sb_slot) {
+		switch (PCI_FUNC(dev->devfn)) {
+		case 2:
+			irq = 10;
+			break;
+		case 3:
+			irq = 11;
+			break;
+		case 5:
+			irq = 9;
+			break;
+		}
+	} else {
+		irq = LOONGSON_IRQ_BASE + 25 + pin;
+	}
+	return irq;
+
+}
+
+/* Do platform specific device initialization at pci_enable_device() time */
+int pcibios_plat_dev_init(struct pci_dev *dev)
+{
+	return 0;
+}
+
+static void loongson2e_nec_fixup(struct pci_dev *pdev)
+{
+	unsigned int val;
+
+	/* Configures port 1, 2, 3, 4 to be validate*/
+	pci_read_config_dword(pdev, 0xe0, &val);
+	pci_write_config_dword(pdev, 0xe0, (val & ~7) | 0x4);
+
+	/* System clock is 48-MHz Oscillator. */
+	pci_write_config_dword(pdev, 0xe4, 1 << 5);
+}
+
+static void loongson2e_686b_func0_fixup(struct pci_dev *pdev)
+{
+	unsigned char c;
+
+	sb_slot = PCI_SLOT(pdev->devfn);
+
+	printk(KERN_INFO "via686b fix: ISA bridge\n");
+
+	/*  Enable I/O Recovery time */
+	pci_write_config_byte(pdev, 0x40, 0x08);
+
+	/*  Enable ISA refresh */
+	pci_write_config_byte(pdev, 0x41, 0x01);
+
+	/*  disable ISA line buffer */
+	pci_write_config_byte(pdev, 0x45, 0x00);
+
+	/*  Gate INTR, and flush line buffer */
+	pci_write_config_byte(pdev, 0x46, 0xe0);
+
+	/*  Disable PCI Delay Transaction, Enable EISA ports 4D0/4D1. */
+	/* pci_write_config_byte(pdev, 0x47, 0x20); */
+
+	/*
+	 *  enable PCI Delay Transaction, Enable EISA ports 4D0/4D1.
+	 *  enable time-out timer
+	 */
+	pci_write_config_byte(pdev, 0x47, 0xe6);
+
+	/*
+	 * enable level trigger on pci irqs: 9,10,11,13
+	 * important! without this PCI interrupts won't work
+	 */
+	outb(0x2e, 0x4d1);
+
+	/*  512 K PCI Decode */
+	pci_write_config_byte(pdev, 0x48, 0x01);
+
+	/*  Wait for PGNT before grant to ISA Master/DMA */
+	pci_write_config_byte(pdev, 0x4a, 0x84);
+
+	/*
+	 * Plug'n'Play
+	 *
+	 *  Parallel DRQ 3, Floppy DRQ 2 (default)
+	 */
+	pci_write_config_byte(pdev, 0x50, 0x0e);
+
+	/*
+	 * IRQ Routing for Floppy and Parallel port
+	 *
+	 *  IRQ 6 for floppy, IRQ 7 for parallel port
+	 */
+	pci_write_config_byte(pdev, 0x51, 0x76);
+
+	/* IRQ Routing for serial ports (take IRQ 3 and 4) */
+	pci_write_config_byte(pdev, 0x52, 0x34);
+
+	/*  All IRQ's level triggered. */
+	pci_write_config_byte(pdev, 0x54, 0x00);
+
+	/* route PIRQA-D irq */
+	pci_write_config_byte(pdev, 0x55, 0x90);	/* bit 7-4, PIRQA */
+	pci_write_config_byte(pdev, 0x56, 0xba);	/* bit 7-4, PIRQC; */
+							/* 3-0, PIRQB */
+	pci_write_config_byte(pdev, 0x57, 0xd0);	/* bit 7-4, PIRQD */
+
+	/* enable function 5/6, audio/modem */
+	pci_read_config_byte(pdev, 0x85, &c);
+	c &= ~(0x3 << 2);
+	pci_write_config_byte(pdev, 0x85, c);
+
+	printk(KERN_INFO"via686b fix: ISA bridge done\n");
+}
+
+static void loongson2e_686b_func1_fixup(struct pci_dev *pdev)
+{
+	printk(KERN_INFO"via686b fix: IDE\n");
+
+	/* Modify IDE controller setup */
+	pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 48);
+	pci_write_config_byte(pdev, PCI_COMMAND,
+			      PCI_COMMAND_IO | PCI_COMMAND_MEMORY |
+			      PCI_COMMAND_MASTER);
+	pci_write_config_byte(pdev, 0x40, 0x0b);
+	/* legacy mode */
+	pci_write_config_byte(pdev, 0x42, 0x09);
+
+#if 1/* play safe, otherwise we may see notebook's usb keyboard lockup */
+	/* disable read prefetch/write post buffers */
+	pci_write_config_byte(pdev, 0x41, 0x02);
+
+	/* use 3/4 as fifo thresh hold	*/
+	pci_write_config_byte(pdev, 0x43, 0x0a);
+	pci_write_config_byte(pdev, 0x44, 0x00);
+
+	pci_write_config_byte(pdev, 0x45, 0x00);
+#else
+	pci_write_config_byte(pdev, 0x41, 0xc2);
+	pci_write_config_byte(pdev, 0x43, 0x35);
+	pci_write_config_byte(pdev, 0x44, 0x1c);
+
+	pci_write_config_byte(pdev, 0x45, 0x10);
+#endif
+
+	printk(KERN_INFO"via686b fix: IDE done\n");
+}
+
+static void loongson2e_686b_func2_fixup(struct pci_dev *pdev)
+{
+	/* irq routing */
+	pci_write_config_byte(pdev, PCI_INTERRUPT_LINE, 10);
+}
+
+static void loongson2e_686b_func3_fixup(struct pci_dev *pdev)
+{
+	/* irq routing */
+	pci_write_config_byte(pdev, PCI_INTERRUPT_LINE, 11);
+}
+
+static void loongson2e_686b_func5_fixup(struct pci_dev *pdev)
+{
+	unsigned int val;
+	unsigned char c;
+
+	/* enable IO */
+	pci_write_config_byte(pdev, PCI_COMMAND,
+			      PCI_COMMAND_IO | PCI_COMMAND_MEMORY |
+			      PCI_COMMAND_MASTER);
+	pci_read_config_dword(pdev, 0x4, &val);
+	pci_write_config_dword(pdev, 0x4, val | 1);
+
+	/* route ac97 IRQ */
+	pci_write_config_byte(pdev, 0x3c, 9);
+
+	pci_read_config_byte(pdev, 0x8, &c);
+
+	/* link control: enable link & SGD PCM output */
+	pci_write_config_byte(pdev, 0x41, 0xcc);
+
+	/* disable game port, FM, midi, sb, enable write to reg2c-2f */
+	pci_write_config_byte(pdev, 0x42, 0x20);
+
+	/* we are using Avance logic codec */
+	pci_write_config_word(pdev, 0x2c, 0x1005);
+	pci_write_config_word(pdev, 0x2e, 0x4710);
+	pci_read_config_dword(pdev, 0x2c, &val);
+
+	pci_write_config_byte(pdev, 0x42, 0x0);
+}
+
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686,
+			 loongson2e_686b_func0_fixup);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_1,
+			 loongson2e_686b_func1_fixup);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_2,
+			 loongson2e_686b_func2_fixup);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_3,
+			 loongson2e_686b_func3_fixup);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_5,
+			 loongson2e_686b_func5_fixup);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_USB,
+			 loongson2e_nec_fixup);
diff --git a/arch/mips/pci/fixup-ip32.c b/arch/mips/pci/fixup-ip32.c
new file mode 100644
index 000000000..d091ffc53
--- /dev/null
+++ b/arch/mips/pci/fixup-ip32.c
@@ -0,0 +1,52 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <asm/ip32/ip32_ints.h>
+/*
+ * O2 has up to 5 PCI devices connected into the MACE bridge.  The device
+ * map looks like this:
+ *
+ * 0  aic7xxx 0
+ * 1  aic7xxx 1
+ * 2  expansion slot
+ * 3  N/C
+ * 4  N/C
+ */
+
+#define SCSI0  MACEPCI_SCSI0_IRQ
+#define SCSI1  MACEPCI_SCSI1_IRQ
+#define INTA0  MACEPCI_SLOT0_IRQ
+#define INTA1  MACEPCI_SLOT1_IRQ
+#define INTA2  MACEPCI_SLOT2_IRQ
+#define INTB   MACEPCI_SHARED0_IRQ
+#define INTC   MACEPCI_SHARED1_IRQ
+#define INTD   MACEPCI_SHARED2_IRQ
+static char irq_tab_mace[][5] = {
+      /* Dummy	INT#A  INT#B  INT#C  INT#D */
+	{0,	    0,	   0,	  0,	 0}, /* This is placeholder row - never used */
+	{0,	SCSI0, SCSI0, SCSI0, SCSI0},
+	{0,	SCSI1, SCSI1, SCSI1, SCSI1},
+	{0,	INTA0,	INTB,  INTC,  INTD},
+	{0,	INTA1,	INTC,  INTD,  INTB},
+	{0,	INTA2,	INTD,  INTB,  INTC},
+};
+
+
+/*
+ * Given a PCI slot number (a la PCI_SLOT(...)) and the interrupt pin of
+ * the device (1-4 => A-D), tell what irq to use.  Note that we don't
+ * in theory have slots 4 and 5, and we never normally use the shared
+ * irqs.  I suppose a device without a pin A will thank us for doing it
+ * right if there exists such a broken piece of crap.
+ */
+int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	return irq_tab_mace[slot][pin];
+}
+
+/* Do platform specific device initialization at pci_enable_device() time */
+int pcibios_plat_dev_init(struct pci_dev *dev)
+{
+	return 0;
+}
diff --git a/arch/mips/pci/fixup-lantiq.c b/arch/mips/pci/fixup-lantiq.c
new file mode 100644
index 000000000..105569c1b
--- /dev/null
+++ b/arch/mips/pci/fixup-lantiq.c
@@ -0,0 +1,27 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ *  Copyright (C) 2012 John Crispin <john@phrozen.org>
+ */
+
+#include <linux/of_irq.h>
+#include <linux/of_pci.h>
+
+int (*ltq_pci_plat_arch_init)(struct pci_dev *dev) = NULL;
+int (*ltq_pci_plat_dev_init)(struct pci_dev *dev) = NULL;
+
+int pcibios_plat_dev_init(struct pci_dev *dev)
+{
+	if (ltq_pci_plat_arch_init)
+		return ltq_pci_plat_arch_init(dev);
+
+	if (ltq_pci_plat_dev_init)
+		return ltq_pci_plat_dev_init(dev);
+
+	return 0;
+}
+
+int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	return of_irq_parse_and_map_pci(dev, slot, pin);
+}
diff --git a/arch/mips/pci/fixup-lemote2f.c b/arch/mips/pci/fixup-lemote2f.c
new file mode 100644
index 000000000..afafda03e
--- /dev/null
+++ b/arch/mips/pci/fixup-lemote2f.c
@@ -0,0 +1,156 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2008 Lemote Technology
+ * Copyright (C) 2004 ICT CAS
+ * Author: Li xiaoyu, lixy@ict.ac.cn
+ *
+ * Copyright (C) 2007 Lemote, Inc.
+ * Author: Fuxin Zhang, zhangfx@lemote.com
+ */
+#include <linux/init.h>
+#include <linux/pci.h>
+
+#include <loongson.h>
+#include <cs5536/cs5536.h>
+#include <cs5536/cs5536_pci.h>
+
+/* PCI interrupt pins
+ *
+ * These should not be changed, or you should consider loongson2f interrupt
+ * register and your pci card dispatch
+ */
+
+#define PCIA		4
+#define PCIB		5
+#define PCIC		6
+#define PCID		7
+
+/* all the pci device has the PCIA pin, check the datasheet. */
+static char irq_tab[][5] = {
+	/*	INTA	INTB	INTC	INTD */
+	{0, 0, 0, 0, 0},	/*  11: Unused */
+	{0, 0, 0, 0, 0},	/*  12: Unused */
+	{0, 0, 0, 0, 0},	/*  13: Unused */
+	{0, 0, 0, 0, 0},	/*  14: Unused */
+	{0, 0, 0, 0, 0},	/*  15: Unused */
+	{0, 0, 0, 0, 0},	/*  16: Unused */
+	{0, PCIA, 0, 0, 0},	/*  17: RTL8110-0 */
+	{0, PCIB, 0, 0, 0},	/*  18: RTL8110-1 */
+	{0, PCIC, 0, 0, 0},	/*  19: SiI3114 */
+	{0, PCID, 0, 0, 0},	/*  20: 3-ports nec usb */
+	{0, PCIA, PCIB, PCIC, PCID},	/*  21: PCI-SLOT */
+	{0, 0, 0, 0, 0},	/*  22: Unused */
+	{0, 0, 0, 0, 0},	/*  23: Unused */
+	{0, 0, 0, 0, 0},	/*  24: Unused */
+	{0, 0, 0, 0, 0},	/*  25: Unused */
+	{0, 0, 0, 0, 0},	/*  26: Unused */
+	{0, 0, 0, 0, 0},	/*  27: Unused */
+};
+
+int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	int virq;
+
+	if ((PCI_SLOT(dev->devfn) != PCI_IDSEL_CS5536)
+	    && (PCI_SLOT(dev->devfn) < 32)) {
+		virq = irq_tab[slot][pin];
+		printk(KERN_INFO "slot: %d, pin: %d, irq: %d\n", slot, pin,
+		       virq + LOONGSON_IRQ_BASE);
+		if (virq != 0)
+			return LOONGSON_IRQ_BASE + virq;
+		else
+			return 0;
+	} else if (PCI_SLOT(dev->devfn) == PCI_IDSEL_CS5536) {	/*  cs5536 */
+		switch (PCI_FUNC(dev->devfn)) {
+		case 2:
+			pci_write_config_byte(dev, PCI_INTERRUPT_LINE,
+					      CS5536_IDE_INTR);
+			return CS5536_IDE_INTR; /*  for IDE */
+		case 3:
+			pci_write_config_byte(dev, PCI_INTERRUPT_LINE,
+					      CS5536_ACC_INTR);
+			return CS5536_ACC_INTR; /*  for AUDIO */
+		case 4: /*  for OHCI */
+		case 5: /*  for EHCI */
+		case 6: /*  for UDC */
+		case 7: /*  for OTG */
+			pci_write_config_byte(dev, PCI_INTERRUPT_LINE,
+					      CS5536_USB_INTR);
+			return CS5536_USB_INTR;
+		}
+		return dev->irq;
+	} else {
+		printk(KERN_INFO "strange PCI slot number.\n");
+		return 0;
+	}
+}
+
+/* Do platform specific device initialization at pci_enable_device() time */
+int pcibios_plat_dev_init(struct pci_dev *dev)
+{
+	return 0;
+}
+
+/* CS5536 SPEC. fixup */
+static void loongson_cs5536_isa_fixup(struct pci_dev *pdev)
+{
+	/* the uart1 and uart2 interrupt in PIC is enabled as default */
+	pci_write_config_dword(pdev, PCI_UART1_INT_REG, 1);
+	pci_write_config_dword(pdev, PCI_UART2_INT_REG, 1);
+}
+
+static void loongson_cs5536_ide_fixup(struct pci_dev *pdev)
+{
+	/* setting the mutex pin as IDE function */
+	pci_write_config_dword(pdev, PCI_IDE_CFG_REG,
+			       CS5536_IDE_FLASH_SIGNATURE);
+}
+
+static void loongson_cs5536_acc_fixup(struct pci_dev *pdev)
+{
+	/* enable the AUDIO interrupt in PIC  */
+	pci_write_config_dword(pdev, PCI_ACC_INT_REG, 1);
+
+	pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0xc0);
+}
+
+static void loongson_cs5536_ohci_fixup(struct pci_dev *pdev)
+{
+	/* enable the OHCI interrupt in PIC */
+	/* THE OHCI, EHCI, UDC, OTG are shared with interrupt in PIC */
+	pci_write_config_dword(pdev, PCI_OHCI_INT_REG, 1);
+}
+
+static void loongson_cs5536_ehci_fixup(struct pci_dev *pdev)
+{
+	u32 hi, lo;
+
+	/* Serial short detect enable */
+	_rdmsr(USB_MSR_REG(USB_CONFIG), &hi, &lo);
+	_wrmsr(USB_MSR_REG(USB_CONFIG), (1 << 1) | (1 << 3), lo);
+
+	/* setting the USB2.0 micro frame length */
+	pci_write_config_dword(pdev, PCI_EHCI_FLADJ_REG, 0x2000);
+}
+
+static void loongson_nec_fixup(struct pci_dev *pdev)
+{
+	unsigned int val;
+
+	pci_read_config_dword(pdev, 0xe0, &val);
+	/* Only 2 port be used */
+	pci_write_config_dword(pdev, 0xe0, (val & ~3) | 0x2);
+}
+
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_ISA,
+			 loongson_cs5536_isa_fixup);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_OHC,
+			 loongson_cs5536_ohci_fixup);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_EHC,
+			 loongson_cs5536_ehci_fixup);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_AUDIO,
+			 loongson_cs5536_acc_fixup);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_IDE,
+			 loongson_cs5536_ide_fixup);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NEC, PCI_DEVICE_ID_NEC_USB,
+			 loongson_nec_fixup);
diff --git a/arch/mips/pci/fixup-malta.c b/arch/mips/pci/fixup-malta.c
new file mode 100644
index 000000000..8131e0ffe
--- /dev/null
+++ b/arch/mips/pci/fixup-malta.c
@@ -0,0 +1,159 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/init.h>
+#include <linux/pci.h>
+#include <asm/mips-boards/piix4.h>
+
+/* PCI interrupt pins */
+#define PCIA		1
+#define PCIB		2
+#define PCIC		3
+#define PCID		4
+
+/* This table is filled in by interrogating the PIIX4 chip */
+static char pci_irq[5] = {
+};
+
+static char irq_tab[][5] = {
+	/*	INTA	INTB	INTC	INTD */
+	{0,	0,	0,	0,	0 },	/*  0: GT64120 PCI bridge */
+	{0,	0,	0,	0,	0 },	/*  1: Unused */
+	{0,	0,	0,	0,	0 },	/*  2: Unused */
+	{0,	0,	0,	0,	0 },	/*  3: Unused */
+	{0,	0,	0,	0,	0 },	/*  4: Unused */
+	{0,	0,	0,	0,	0 },	/*  5: Unused */
+	{0,	0,	0,	0,	0 },	/*  6: Unused */
+	{0,	0,	0,	0,	0 },	/*  7: Unused */
+	{0,	0,	0,	0,	0 },	/*  8: Unused */
+	{0,	0,	0,	0,	0 },	/*  9: Unused */
+	{0,	0,	0,	0,	PCID }, /* 10: PIIX4 USB */
+	{0,	PCIB,	0,	0,	0 },	/* 11: AMD 79C973 Ethernet */
+	{0,	PCIC,	0,	0,	0 },	/* 12: Crystal 4281 Sound */
+	{0,	0,	0,	0,	0 },	/* 13: Unused */
+	{0,	0,	0,	0,	0 },	/* 14: Unused */
+	{0,	0,	0,	0,	0 },	/* 15: Unused */
+	{0,	0,	0,	0,	0 },	/* 16: Unused */
+	{0,	0,	0,	0,	0 },	/* 17: Bonito/SOC-it PCI Bridge*/
+	{0,	PCIA,	PCIB,	PCIC,	PCID }, /* 18: PCI Slot 1 */
+	{0,	PCIB,	PCIC,	PCID,	PCIA }, /* 19: PCI Slot 2 */
+	{0,	PCIC,	PCID,	PCIA,	PCIB }, /* 20: PCI Slot 3 */
+	{0,	PCID,	PCIA,	PCIB,	PCIC }	/* 21: PCI Slot 4 */
+};
+
+int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	int virq;
+	virq = irq_tab[slot][pin];
+	return pci_irq[virq];
+}
+
+/* Do platform specific device initialization at pci_enable_device() time */
+int pcibios_plat_dev_init(struct pci_dev *dev)
+{
+	return 0;
+}
+
+static void malta_piix_func3_base_fixup(struct pci_dev *dev)
+{
+	/* Set a sane PM I/O base address */
+	pci_write_config_word(dev, PIIX4_FUNC3_PMBA, 0x1000);
+
+	/* Enable access to the PM I/O region */
+	pci_write_config_byte(dev, PIIX4_FUNC3_PMREGMISC,
+			      PIIX4_FUNC3_PMREGMISC_EN);
+}
+
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB_3,
+			malta_piix_func3_base_fixup);
+
+static void malta_piix_func0_fixup(struct pci_dev *pdev)
+{
+	unsigned char reg_val;
+	u32 reg_val32;
+	u16 reg_val16;
+	/* PIIX PIRQC[A:D] irq mappings */
+	static int piixirqmap[PIIX4_FUNC0_PIRQRC_IRQ_ROUTING_MAX] = {
+		0,  0,	0,  3,
+		4,  5,	6,  7,
+		0,  9, 10, 11,
+		12, 0, 14, 15
+	};
+	int i;
+
+	/* Interrogate PIIX4 to get PCI IRQ mapping */
+	for (i = 0; i <= 3; i++) {
+		pci_read_config_byte(pdev, PIIX4_FUNC0_PIRQRC+i, &reg_val);
+		if (reg_val & PIIX4_FUNC0_PIRQRC_IRQ_ROUTING_DISABLE)
+			pci_irq[PCIA+i] = 0;	/* Disabled */
+		else
+			pci_irq[PCIA+i] = piixirqmap[reg_val &
+				PIIX4_FUNC0_PIRQRC_IRQ_ROUTING_MASK];
+	}
+
+	/* Done by YAMON 2.00 onwards */
+	if (PCI_SLOT(pdev->devfn) == 10) {
+		/*
+		 * Set top of main memory accessible by ISA or DMA
+		 * devices to 16 Mb.
+		 */
+		pci_read_config_byte(pdev, PIIX4_FUNC0_TOM, &reg_val);
+		pci_write_config_byte(pdev, PIIX4_FUNC0_TOM, reg_val |
+				PIIX4_FUNC0_TOM_TOP_OF_MEMORY_MASK);
+	}
+
+	/* Mux SERIRQ to its pin */
+	pci_read_config_dword(pdev, PIIX4_FUNC0_GENCFG, &reg_val32);
+	pci_write_config_dword(pdev, PIIX4_FUNC0_GENCFG,
+			       reg_val32 | PIIX4_FUNC0_GENCFG_SERIRQ);
+
+	/* Enable SERIRQ */
+	pci_read_config_byte(pdev, PIIX4_FUNC0_SERIRQC, &reg_val);
+	reg_val |= PIIX4_FUNC0_SERIRQC_EN | PIIX4_FUNC0_SERIRQC_CONT;
+	pci_write_config_byte(pdev, PIIX4_FUNC0_SERIRQC, reg_val);
+
+	/* Enable response to special cycles */
+	pci_read_config_word(pdev, PCI_COMMAND, &reg_val16);
+	pci_write_config_word(pdev, PCI_COMMAND,
+			      reg_val16 | PCI_COMMAND_SPECIAL);
+}
+
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB_0,
+	 malta_piix_func0_fixup);
+
+static void malta_piix_func1_fixup(struct pci_dev *pdev)
+{
+	unsigned char reg_val;
+
+	/* Done by YAMON 2.02 onwards */
+	if (PCI_SLOT(pdev->devfn) == 10) {
+		/*
+		 * IDE Decode enable.
+		 */
+		pci_read_config_byte(pdev, PIIX4_FUNC1_IDETIM_PRIMARY_HI,
+			&reg_val);
+		pci_write_config_byte(pdev, PIIX4_FUNC1_IDETIM_PRIMARY_HI,
+			reg_val|PIIX4_FUNC1_IDETIM_PRIMARY_HI_IDE_DECODE_EN);
+		pci_read_config_byte(pdev, PIIX4_FUNC1_IDETIM_SECONDARY_HI,
+			&reg_val);
+		pci_write_config_byte(pdev, PIIX4_FUNC1_IDETIM_SECONDARY_HI,
+			reg_val|PIIX4_FUNC1_IDETIM_SECONDARY_HI_IDE_DECODE_EN);
+	}
+}
+
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB,
+	 malta_piix_func1_fixup);
+
+/* Enable PCI 2.1 compatibility in PIIX4 */
+static void quirk_dlcsetup(struct pci_dev *dev)
+{
+	u8 odlc, ndlc;
+
+	(void) pci_read_config_byte(dev, PIIX4_FUNC0_DLC, &odlc);
+	/* Enable passive releases and delayed transaction */
+	ndlc = odlc | PIIX4_FUNC0_DLC_USBPR_EN |
+		      PIIX4_FUNC0_DLC_PASSIVE_RELEASE_EN |
+		      PIIX4_FUNC0_DLC_DELAYED_TRANSACTION_EN;
+	(void) pci_write_config_byte(dev, PIIX4_FUNC0_DLC, ndlc);
+}
+
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB_0,
+	quirk_dlcsetup);
diff --git a/arch/mips/pci/fixup-rbtx4927.c b/arch/mips/pci/fixup-rbtx4927.c
new file mode 100644
index 000000000..d6aaed1d6
--- /dev/null
+++ b/arch/mips/pci/fixup-rbtx4927.c
@@ -0,0 +1,73 @@
+/*
+ *
+ * BRIEF MODULE DESCRIPTION
+ *      Board specific pci fixups for the Toshiba rbtx4927
+ *
+ * Copyright 2001 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc.
+ *              ppopov@mvista.com or source@mvista.com
+ *
+ * Copyright (C) 2000-2001 Toshiba Corporation
+ *
+ * Copyright (C) 2004 MontaVista Software Inc.
+ * Author: Manish Lachwani (mlachwani@mvista.com)
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+#include <linux/types.h>
+#include <asm/txx9/pci.h>
+#include <asm/txx9/rbtx4927.h>
+
+int rbtx4927_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	unsigned char irq = pin;
+
+	/* IRQ rotation */
+	irq--;			/* 0-3 */
+	if (slot == TX4927_PCIC_IDSEL_AD_TO_SLOT(23)) {
+		/* PCI CardSlot (IDSEL=A23) */
+		/* PCIA => PCIA */
+		irq = (irq + 0 + slot) % 4;
+	} else {
+		/* PCI Backplane */
+		if (txx9_pci_option & TXX9_PCI_OPT_PICMG)
+			irq = (irq + 33 - slot) % 4;
+		else
+			irq = (irq + 3 + slot) % 4;
+	}
+	irq++;	/* 1-4 */
+
+	switch (irq) {
+	case 1:
+		irq = RBTX4927_IRQ_IOC_PCIA;
+		break;
+	case 2:
+		irq = RBTX4927_IRQ_IOC_PCIB;
+		break;
+	case 3:
+		irq = RBTX4927_IRQ_IOC_PCIC;
+		break;
+	case 4:
+		irq = RBTX4927_IRQ_IOC_PCID;
+		break;
+	}
+	return irq;
+}
diff --git a/arch/mips/pci/fixup-rc32434.c b/arch/mips/pci/fixup-rc32434.c
new file mode 100644
index 000000000..7fcafd5da
--- /dev/null
+++ b/arch/mips/pci/fixup-rc32434.c
@@ -0,0 +1,69 @@
+/*
+ * Copyright 2001 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc.
+ *         	stevel@mvista.com or source@mvista.com
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+
+#include <asm/mach-rc32434/rc32434.h>
+#include <asm/mach-rc32434/irq.h>
+
+static int irq_map[2][12] = {
+	{0, 0, 2, 3, 2, 3, 0, 0, 0, 0, 0, 1},
+	{0, 0, 1, 3, 0, 2, 1, 3, 0, 2, 1, 3}
+};
+
+int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	int irq = 0;
+
+	if (dev->bus->number < 2 && PCI_SLOT(dev->devfn) < 12)
+		irq = irq_map[dev->bus->number][PCI_SLOT(dev->devfn)];
+
+	return irq + GROUP4_IRQ_BASE + 4;
+}
+
+static void rc32434_pci_early_fixup(struct pci_dev *dev)
+{
+	if (PCI_SLOT(dev->devfn) == 6 && dev->bus->number == 0) {
+		/* disable prefetched memory range */
+		pci_write_config_word(dev, PCI_PREF_MEMORY_LIMIT, 0);
+		pci_write_config_word(dev, PCI_PREF_MEMORY_BASE, 0x10);
+
+		pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, 4);
+	}
+}
+
+/*
+ * The fixup applies to both the IDT and VIA devices present on the board
+ */
+DECLARE_PCI_FIXUP_HEADER(PCI_ANY_ID, PCI_ANY_ID, rc32434_pci_early_fixup);
+
+/* Do platform specific device initialization at pci_enable_device() time */
+int pcibios_plat_dev_init(struct pci_dev *dev)
+{
+	return 0;
+}
diff --git a/arch/mips/pci/fixup-sb1250.c b/arch/mips/pci/fixup-sb1250.c
new file mode 100644
index 000000000..3f914c33b
--- /dev/null
+++ b/arch/mips/pci/fixup-sb1250.c
@@ -0,0 +1,91 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *	Copyright (C) 2004, 2006  MIPS Technologies, Inc.  All rights reserved.
+ *	    Author:	Maciej W. Rozycki <macro@mips.com>
+ *	Copyright (C) 2018  Maciej W. Rozycki
+ */
+
+#include <linux/dma-mapping.h>
+#include <linux/pci.h>
+
+/*
+ * Set the BCM1250, etc. PCI host bridge's TRDY timeout
+ * to the finite max.
+ */
+static void quirk_sb1250_pci(struct pci_dev *dev)
+{
+	pci_write_config_byte(dev, 0x40, 0xff);
+}
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SIBYTE, PCI_DEVICE_ID_BCM1250_PCI,
+			quirk_sb1250_pci);
+
+/*
+ * The BCM1250, etc. PCI host bridge does not support DAC on its 32-bit
+ * bus, so we set the bus's DMA limit accordingly.  However the HT link
+ * down the artificial PCI-HT bridge supports 40-bit addressing and the
+ * SP1011 HT-PCI bridge downstream supports both DAC and a 64-bit bus
+ * width, so we record the PCI-HT bridge's secondary and subordinate bus
+ * numbers and do not set the limit for devices present in the inclusive
+ * range of those.
+ */
+struct sb1250_bus_dma_limit_exclude {
+	bool set;
+	unsigned char start;
+	unsigned char end;
+};
+
+static int sb1250_bus_dma_limit(struct pci_dev *dev, void *data)
+{
+	struct sb1250_bus_dma_limit_exclude *exclude = data;
+	bool exclude_this;
+	bool ht_bridge;
+
+	exclude_this = exclude->set && (dev->bus->number >= exclude->start &&
+					dev->bus->number <= exclude->end);
+	ht_bridge = !exclude->set && (dev->vendor == PCI_VENDOR_ID_SIBYTE &&
+				      dev->device == PCI_DEVICE_ID_BCM1250_HT);
+
+	if (exclude_this) {
+		dev_dbg(&dev->dev, "not disabling DAC for device");
+	} else if (ht_bridge) {
+		exclude->start = dev->subordinate->number;
+		exclude->end = pci_bus_max_busnr(dev->subordinate);
+		exclude->set = true;
+		dev_dbg(&dev->dev, "not disabling DAC for [bus %02x-%02x]",
+			exclude->start, exclude->end);
+	} else {
+		dev_dbg(&dev->dev, "disabling DAC for device");
+		dev->dev.bus_dma_limit = DMA_BIT_MASK(32);
+	}
+
+	return 0;
+}
+
+static void quirk_sb1250_pci_dac(struct pci_dev *dev)
+{
+	struct sb1250_bus_dma_limit_exclude exclude = { .set = false };
+
+	pci_walk_bus(dev->bus, sb1250_bus_dma_limit, &exclude);
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SIBYTE, PCI_DEVICE_ID_BCM1250_PCI,
+			quirk_sb1250_pci_dac);
+
+/*
+ * The BCM1250, etc. PCI/HT bridge reports as a host bridge.
+ */
+static void quirk_sb1250_ht(struct pci_dev *dev)
+{
+	dev->class = PCI_CLASS_BRIDGE_PCI_NORMAL;
+}
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SIBYTE, PCI_DEVICE_ID_BCM1250_HT,
+			quirk_sb1250_ht);
+
+/*
+ * Set the SP1011 HT/PCI bridge's TRDY timeout to the finite max.
+ */
+static void quirk_sp1011(struct pci_dev *dev)
+{
+	pci_write_config_byte(dev, 0x64, 0xff);
+}
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_SIPACKETS, PCI_DEVICE_ID_SP1011,
+			quirk_sp1011);
diff --git a/arch/mips/pci/fixup-sni.c b/arch/mips/pci/fixup-sni.c
new file mode 100644
index 000000000..de012f8bd
--- /dev/null
+++ b/arch/mips/pci/fixup-sni.c
@@ -0,0 +1,169 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * SNI specific PCI support for RM200/RM300.
+ *
+ * Copyright (C) 1997 - 2000, 2003, 04 Ralf Baechle (ralf@linux-mips.org)
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/pci.h>
+
+#include <asm/mipsregs.h>
+#include <asm/sni.h>
+
+#include <irq.h>
+
+/*
+ * PCIMT Shortcuts ...
+ */
+#define SCSI	PCIMT_IRQ_SCSI
+#define ETH	PCIMT_IRQ_ETHERNET
+#define INTA	PCIMT_IRQ_INTA
+#define INTB	PCIMT_IRQ_INTB
+#define INTC	PCIMT_IRQ_INTC
+#define INTD	PCIMT_IRQ_INTD
+
+/*
+ * Device 0: PCI EISA Bridge	(directly routed)
+ * Device 1: NCR53c810 SCSI	(directly routed)
+ * Device 2: PCnet32 Ethernet	(directly routed)
+ * Device 3: VGA		(routed to INTB)
+ * Device 4: Unused
+ * Device 5: Slot 2
+ * Device 6: Slot 3
+ * Device 7: Slot 4
+ *
+ * Documentation says the VGA is device 5 and device 3 is unused but that
+ * seem to be a documentation error.  At least on my RM200C the Cirrus
+ * Logic CL-GD5434 VGA is device 3.
+ */
+static char irq_tab_rm200[8][5] = {
+	/*	 INTA  INTB  INTC  INTD */
+	{     0,    0,	  0,	0,    0 },	/* EISA bridge */
+	{  SCSI, SCSI, SCSI, SCSI, SCSI },	/* SCSI */
+	{   ETH,  ETH,	ETH,  ETH,  ETH },	/* Ethernet */
+	{  INTB, INTB, INTB, INTB, INTB },	/* VGA */
+	{     0,    0,	  0,	0,    0 },	/* Unused */
+	{     0, INTB, INTC, INTD, INTA },	/* Slot 2 */
+	{     0, INTC, INTD, INTA, INTB },	/* Slot 3 */
+	{     0, INTD, INTA, INTB, INTC },	/* Slot 4 */
+};
+
+/*
+ * In Revision D of the RM300 Device 2 has become a normal purpose Slot 1
+ *
+ * The VGA card is optional for RM300 systems.
+ */
+static char irq_tab_rm300d[8][5] = {
+	/*	 INTA  INTB  INTC  INTD */
+	{     0,    0,	  0,	0,    0 },	/* EISA bridge */
+	{  SCSI, SCSI, SCSI, SCSI, SCSI },	/* SCSI */
+	{     0, INTC, INTD, INTA, INTB },	/* Slot 1 */
+	{  INTB, INTB, INTB, INTB, INTB },	/* VGA */
+	{     0,    0,	  0,	0,    0 },	/* Unused */
+	{     0, INTB, INTC, INTD, INTA },	/* Slot 2 */
+	{     0, INTC, INTD, INTA, INTB },	/* Slot 3 */
+	{     0, INTD, INTA, INTB, INTC },	/* Slot 4 */
+};
+
+static char irq_tab_rm300e[5][5] = {
+	/*	 INTA  INTB  INTC  INTD */
+	{     0,    0,	  0,	0,    0 },	/* HOST bridge */
+	{  SCSI, SCSI, SCSI, SCSI, SCSI },	/* SCSI */
+	{     0, INTC, INTD, INTA, INTB },	/* Bridge/i960 */
+	{     0, INTD, INTA, INTB, INTC },	/* Slot 1 */
+	{     0, INTA, INTB, INTC, INTD },	/* Slot 2 */
+};
+#undef SCSI
+#undef ETH
+#undef INTA
+#undef INTB
+#undef INTC
+#undef INTD
+
+
+/*
+ * PCIT Shortcuts ...
+ */
+#define SCSI0	PCIT_IRQ_SCSI0
+#define SCSI1	PCIT_IRQ_SCSI1
+#define ETH	PCIT_IRQ_ETHERNET
+#define INTA	PCIT_IRQ_INTA
+#define INTB	PCIT_IRQ_INTB
+#define INTC	PCIT_IRQ_INTC
+#define INTD	PCIT_IRQ_INTD
+
+static char irq_tab_pcit[13][5] = {
+	/*	 INTA  INTB  INTC  INTD */
+	{     0,     0,	    0,	   0,	  0 },	/* HOST bridge */
+	{ SCSI0, SCSI0, SCSI0, SCSI0, SCSI0 },	/* SCSI */
+	{ SCSI1, SCSI1, SCSI1, SCSI1, SCSI1 },	/* SCSI */
+	{   ETH,   ETH,	  ETH,	 ETH,	ETH },	/* Ethernet */
+	{     0,  INTA,	 INTB,	INTC,  INTD },	/* PCI-PCI bridge */
+	{     0,     0,	    0,	   0,	  0 },	/* Unused */
+	{     0,     0,	    0,	   0,	  0 },	/* Unused */
+	{     0,     0,	    0,	   0,	  0 },	/* Unused */
+	{     0,  INTA,	 INTB,	INTC,  INTD },	/* Slot 1 */
+	{     0,  INTB,	 INTC,	INTD,  INTA },	/* Slot 2 */
+	{     0,  INTC,	 INTD,	INTA,  INTB },	/* Slot 3 */
+	{     0,  INTD,	 INTA,	INTB,  INTC },	/* Slot 4 */
+	{     0,  INTA,	 INTB,	INTC,  INTD },	/* Slot 5 */
+};
+
+static char irq_tab_pcit_cplus[13][5] = {
+	/*	 INTA  INTB  INTC  INTD */
+	{     0,     0,	    0,	   0,	  0 },	/* HOST bridge */
+	{     0,  INTB,	 INTC,	INTD,  INTA },	/* PCI Slot 9 */
+	{     0,     0,	    0,	   0,	  0 },	/* PCI-EISA */
+	{     0,     0,	    0,	   0,	  0 },	/* Unused */
+	{     0,  INTA,	 INTB,	INTC,  INTD },	/* PCI-PCI bridge */
+	{     0,  INTB,	 INTC,	INTD,  INTA },	/* fixup */
+};
+
+static inline int is_rm300_revd(void)
+{
+	unsigned char csmsr = *(volatile unsigned char *)PCIMT_CSMSR;
+
+	return (csmsr & 0xa0) == 0x20;
+}
+
+int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	switch (sni_brd_type) {
+	case SNI_BRD_PCI_TOWER_CPLUS:
+		if (slot == 4) {
+			/*
+			 * SNI messed up interrupt wiring for onboard
+			 * PCI bus 1; we need to fix this up here
+			 */
+			while (dev && dev->bus->number != 1)
+				dev = dev->bus->self;
+			if (dev && dev->devfn >= PCI_DEVFN(4, 0))
+				slot = 5;
+		}
+		return irq_tab_pcit_cplus[slot][pin];
+	case SNI_BRD_PCI_TOWER:
+		return irq_tab_pcit[slot][pin];
+
+	case SNI_BRD_PCI_MTOWER:
+		if (is_rm300_revd())
+			return irq_tab_rm300d[slot][pin];
+		fallthrough;
+	case SNI_BRD_PCI_DESKTOP:
+		return irq_tab_rm200[slot][pin];
+
+	case SNI_BRD_PCI_MTOWER_CPLUS:
+		return irq_tab_rm300e[slot][pin];
+	}
+
+	return 0;
+}
+
+/* Do platform specific device initialization at pci_enable_device() time */
+int pcibios_plat_dev_init(struct pci_dev *dev)
+{
+	return 0;
+}
diff --git a/arch/mips/pci/msi-octeon.c b/arch/mips/pci/msi-octeon.c
new file mode 100644
index 000000000..abc3b61bf
--- /dev/null
+++ b/arch/mips/pci/msi-octeon.c
@@ -0,0 +1,414 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2005-2009, 2010 Cavium Networks
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/msi.h>
+#include <linux/spinlock.h>
+#include <linux/interrupt.h>
+
+#include <asm/octeon/octeon.h>
+#include <asm/octeon/cvmx-npi-defs.h>
+#include <asm/octeon/cvmx-pci-defs.h>
+#include <asm/octeon/cvmx-npei-defs.h>
+#include <asm/octeon/cvmx-sli-defs.h>
+#include <asm/octeon/cvmx-pexp-defs.h>
+#include <asm/octeon/pci-octeon.h>
+
+/*
+ * Each bit in msi_free_irq_bitmask represents a MSI interrupt that is
+ * in use.
+ */
+static u64 msi_free_irq_bitmask[4];
+
+/*
+ * Each bit in msi_multiple_irq_bitmask tells that the device using
+ * this bit in msi_free_irq_bitmask is also using the next bit. This
+ * is used so we can disable all of the MSI interrupts when a device
+ * uses multiple.
+ */
+static u64 msi_multiple_irq_bitmask[4];
+
+/*
+ * This lock controls updates to msi_free_irq_bitmask and
+ * msi_multiple_irq_bitmask.
+ */
+static DEFINE_SPINLOCK(msi_free_irq_bitmask_lock);
+
+/*
+ * Number of MSI IRQs used. This variable is set up in
+ * the module init time.
+ */
+static int msi_irq_size;
+
+/**
+ * arch_setup_msi_irq() - setup MSI IRQs for a device
+ * @dev:    Device requesting MSI interrupts
+ * @desc:   MSI descriptor
+ *
+ * Called when a driver requests MSI interrupts instead of the
+ * legacy INT A-D. This routine will allocate multiple interrupts
+ * for MSI devices that support them. A device can override this by
+ * programming the MSI control bits [6:4] before calling
+ * pci_enable_msi().
+ *
+ * Return: %0 on success, non-%0 on error.
+ */
+int arch_setup_msi_irq(struct pci_dev *dev, struct msi_desc *desc)
+{
+	struct msi_msg msg;
+	u16 control;
+	int configured_private_bits;
+	int request_private_bits;
+	int irq = 0;
+	int irq_step;
+	u64 search_mask;
+	int index;
+
+	if (desc->pci.msi_attrib.is_msix)
+		return -EINVAL;
+
+	/*
+	 * Read the MSI config to figure out how many IRQs this device
+	 * wants.  Most devices only want 1, which will give
+	 * configured_private_bits and request_private_bits equal 0.
+	 */
+	pci_read_config_word(dev, dev->msi_cap + PCI_MSI_FLAGS, &control);
+
+	/*
+	 * If the number of private bits has been configured then use
+	 * that value instead of the requested number. This gives the
+	 * driver the chance to override the number of interrupts
+	 * before calling pci_enable_msi().
+	 */
+	configured_private_bits = (control & PCI_MSI_FLAGS_QSIZE) >> 4;
+	if (configured_private_bits == 0) {
+		/* Nothing is configured, so use the hardware requested size */
+		request_private_bits = (control & PCI_MSI_FLAGS_QMASK) >> 1;
+	} else {
+		/*
+		 * Use the number of configured bits, assuming the
+		 * driver wanted to override the hardware request
+		 * value.
+		 */
+		request_private_bits = configured_private_bits;
+	}
+
+	/*
+	 * The PCI 2.3 spec mandates that there are at most 32
+	 * interrupts. If this device asks for more, only give it one.
+	 */
+	if (request_private_bits > 5)
+		request_private_bits = 0;
+
+try_only_one:
+	/*
+	 * The IRQs have to be aligned on a power of two based on the
+	 * number being requested.
+	 */
+	irq_step = 1 << request_private_bits;
+
+	/* Mask with one bit for each IRQ */
+	search_mask = (1 << irq_step) - 1;
+
+	/*
+	 * We're going to search msi_free_irq_bitmask_lock for zero
+	 * bits. This represents an MSI interrupt number that isn't in
+	 * use.
+	 */
+	spin_lock(&msi_free_irq_bitmask_lock);
+	for (index = 0; index < msi_irq_size/64; index++) {
+		for (irq = 0; irq < 64; irq += irq_step) {
+			if ((msi_free_irq_bitmask[index] & (search_mask << irq)) == 0) {
+				msi_free_irq_bitmask[index] |= search_mask << irq;
+				msi_multiple_irq_bitmask[index] |= (search_mask >> 1) << irq;
+				goto msi_irq_allocated;
+			}
+		}
+	}
+msi_irq_allocated:
+	spin_unlock(&msi_free_irq_bitmask_lock);
+
+	/* Make sure the search for available interrupts didn't fail */
+	if (irq >= 64) {
+		if (request_private_bits) {
+			pr_err("arch_setup_msi_irq: Unable to find %d free interrupts, trying just one",
+			       1 << request_private_bits);
+			request_private_bits = 0;
+			goto try_only_one;
+		} else
+			panic("arch_setup_msi_irq: Unable to find a free MSI interrupt");
+	}
+
+	/* MSI interrupts start at logical IRQ OCTEON_IRQ_MSI_BIT0 */
+	irq += index*64;
+	irq += OCTEON_IRQ_MSI_BIT0;
+
+	switch (octeon_dma_bar_type) {
+	case OCTEON_DMA_BAR_TYPE_SMALL:
+		/* When not using big bar, Bar 0 is based at 128MB */
+		msg.address_lo =
+			((128ul << 20) + CVMX_PCI_MSI_RCV) & 0xffffffff;
+		msg.address_hi = ((128ul << 20) + CVMX_PCI_MSI_RCV) >> 32;
+		break;
+	case OCTEON_DMA_BAR_TYPE_BIG:
+		/* When using big bar, Bar 0 is based at 0 */
+		msg.address_lo = (0 + CVMX_PCI_MSI_RCV) & 0xffffffff;
+		msg.address_hi = (0 + CVMX_PCI_MSI_RCV) >> 32;
+		break;
+	case OCTEON_DMA_BAR_TYPE_PCIE:
+		/* When using PCIe, Bar 0 is based at 0 */
+		/* FIXME CVMX_NPEI_MSI_RCV* other than 0? */
+		msg.address_lo = (0 + CVMX_NPEI_PCIE_MSI_RCV) & 0xffffffff;
+		msg.address_hi = (0 + CVMX_NPEI_PCIE_MSI_RCV) >> 32;
+		break;
+	case OCTEON_DMA_BAR_TYPE_PCIE2:
+		/* When using PCIe2, Bar 0 is based at 0 */
+		msg.address_lo = (0 + CVMX_SLI_PCIE_MSI_RCV) & 0xffffffff;
+		msg.address_hi = (0 + CVMX_SLI_PCIE_MSI_RCV) >> 32;
+		break;
+	default:
+		panic("arch_setup_msi_irq: Invalid octeon_dma_bar_type");
+	}
+	msg.data = irq - OCTEON_IRQ_MSI_BIT0;
+
+	/* Update the number of IRQs the device has available to it */
+	control &= ~PCI_MSI_FLAGS_QSIZE;
+	control |= request_private_bits << 4;
+	pci_write_config_word(dev, dev->msi_cap + PCI_MSI_FLAGS, control);
+
+	irq_set_msi_desc(irq, desc);
+	pci_write_msi_msg(irq, &msg);
+	return 0;
+}
+
+/**
+ * arch_teardown_msi_irq() - release MSI IRQs for a device
+ * @irq:    The devices first irq number. There may be multiple in sequence.
+ *
+ * Called when a device no longer needs its MSI interrupts. All
+ * MSI interrupts for the device are freed.
+ */
+void arch_teardown_msi_irq(unsigned int irq)
+{
+	int number_irqs;
+	u64 bitmask;
+	int index = 0;
+	int irq0;
+
+	if ((irq < OCTEON_IRQ_MSI_BIT0)
+		|| (irq > msi_irq_size + OCTEON_IRQ_MSI_BIT0))
+		panic("arch_teardown_msi_irq: Attempted to teardown illegal "
+		      "MSI interrupt (%d)", irq);
+
+	irq -= OCTEON_IRQ_MSI_BIT0;
+	index = irq / 64;
+	irq0 = irq % 64;
+
+	/*
+	 * Count the number of IRQs we need to free by looking at the
+	 * msi_multiple_irq_bitmask. Each bit set means that the next
+	 * IRQ is also owned by this device.
+	 */
+	number_irqs = 0;
+	while ((irq0 + number_irqs < 64) &&
+	       (msi_multiple_irq_bitmask[index]
+		& (1ull << (irq0 + number_irqs))))
+		number_irqs++;
+	number_irqs++;
+	/* Mask with one bit for each IRQ */
+	bitmask = (1 << number_irqs) - 1;
+	/* Shift the mask to the correct bit location */
+	bitmask <<= irq0;
+	if ((msi_free_irq_bitmask[index] & bitmask) != bitmask)
+		panic("arch_teardown_msi_irq: Attempted to teardown MSI "
+		      "interrupt (%d) not in use", irq);
+
+	/* Checks are done, update the in use bitmask */
+	spin_lock(&msi_free_irq_bitmask_lock);
+	msi_free_irq_bitmask[index] &= ~bitmask;
+	msi_multiple_irq_bitmask[index] &= ~bitmask;
+	spin_unlock(&msi_free_irq_bitmask_lock);
+}
+
+static DEFINE_RAW_SPINLOCK(octeon_irq_msi_lock);
+
+static u64 msi_rcv_reg[4];
+static u64 mis_ena_reg[4];
+
+static void octeon_irq_msi_enable_pcie(struct irq_data *data)
+{
+	u64 en;
+	unsigned long flags;
+	int msi_number = data->irq - OCTEON_IRQ_MSI_BIT0;
+	int irq_index = msi_number >> 6;
+	int irq_bit = msi_number & 0x3f;
+
+	raw_spin_lock_irqsave(&octeon_irq_msi_lock, flags);
+	en = cvmx_read_csr(mis_ena_reg[irq_index]);
+	en |= 1ull << irq_bit;
+	cvmx_write_csr(mis_ena_reg[irq_index], en);
+	cvmx_read_csr(mis_ena_reg[irq_index]);
+	raw_spin_unlock_irqrestore(&octeon_irq_msi_lock, flags);
+}
+
+static void octeon_irq_msi_disable_pcie(struct irq_data *data)
+{
+	u64 en;
+	unsigned long flags;
+	int msi_number = data->irq - OCTEON_IRQ_MSI_BIT0;
+	int irq_index = msi_number >> 6;
+	int irq_bit = msi_number & 0x3f;
+
+	raw_spin_lock_irqsave(&octeon_irq_msi_lock, flags);
+	en = cvmx_read_csr(mis_ena_reg[irq_index]);
+	en &= ~(1ull << irq_bit);
+	cvmx_write_csr(mis_ena_reg[irq_index], en);
+	cvmx_read_csr(mis_ena_reg[irq_index]);
+	raw_spin_unlock_irqrestore(&octeon_irq_msi_lock, flags);
+}
+
+static struct irq_chip octeon_irq_chip_msi_pcie = {
+	.name = "MSI",
+	.irq_enable = octeon_irq_msi_enable_pcie,
+	.irq_disable = octeon_irq_msi_disable_pcie,
+};
+
+static void octeon_irq_msi_enable_pci(struct irq_data *data)
+{
+	/*
+	 * Octeon PCI doesn't have the ability to mask/unmask MSI
+	 * interrupts individually. Instead of masking/unmasking them
+	 * in groups of 16, we simple assume MSI devices are well
+	 * behaved. MSI interrupts are always enable and the ACK is
+	 * assumed to be enough
+	 */
+}
+
+static void octeon_irq_msi_disable_pci(struct irq_data *data)
+{
+	/* See comment in enable */
+}
+
+static struct irq_chip octeon_irq_chip_msi_pci = {
+	.name = "MSI",
+	.irq_enable = octeon_irq_msi_enable_pci,
+	.irq_disable = octeon_irq_msi_disable_pci,
+};
+
+/*
+ * Called by the interrupt handling code when an MSI interrupt
+ * occurs.
+ */
+static irqreturn_t __octeon_msi_do_interrupt(int index, u64 msi_bits)
+{
+	int irq;
+	int bit;
+
+	bit = fls64(msi_bits);
+	if (bit) {
+		bit--;
+		/* Acknowledge it first. */
+		cvmx_write_csr(msi_rcv_reg[index], 1ull << bit);
+
+		irq = bit + OCTEON_IRQ_MSI_BIT0 + 64 * index;
+		do_IRQ(irq);
+		return IRQ_HANDLED;
+	}
+	return IRQ_NONE;
+}
+
+#define OCTEON_MSI_INT_HANDLER_X(x)					\
+static irqreturn_t octeon_msi_interrupt##x(int cpl, void *dev_id)	\
+{									\
+	u64 msi_bits = cvmx_read_csr(msi_rcv_reg[(x)]);			\
+	return __octeon_msi_do_interrupt((x), msi_bits);		\
+}
+
+/*
+ * Create octeon_msi_interrupt{0-3} function body
+ */
+OCTEON_MSI_INT_HANDLER_X(0);
+OCTEON_MSI_INT_HANDLER_X(1);
+OCTEON_MSI_INT_HANDLER_X(2);
+OCTEON_MSI_INT_HANDLER_X(3);
+
+/*
+ * Initializes the MSI interrupt handling code
+ */
+int __init octeon_msi_initialize(void)
+{
+	int irq;
+	struct irq_chip *msi;
+
+	if (octeon_dma_bar_type == OCTEON_DMA_BAR_TYPE_INVALID) {
+		return 0;
+	} else if (octeon_dma_bar_type == OCTEON_DMA_BAR_TYPE_PCIE) {
+		msi_rcv_reg[0] = CVMX_PEXP_NPEI_MSI_RCV0;
+		msi_rcv_reg[1] = CVMX_PEXP_NPEI_MSI_RCV1;
+		msi_rcv_reg[2] = CVMX_PEXP_NPEI_MSI_RCV2;
+		msi_rcv_reg[3] = CVMX_PEXP_NPEI_MSI_RCV3;
+		mis_ena_reg[0] = CVMX_PEXP_NPEI_MSI_ENB0;
+		mis_ena_reg[1] = CVMX_PEXP_NPEI_MSI_ENB1;
+		mis_ena_reg[2] = CVMX_PEXP_NPEI_MSI_ENB2;
+		mis_ena_reg[3] = CVMX_PEXP_NPEI_MSI_ENB3;
+		msi = &octeon_irq_chip_msi_pcie;
+	} else {
+		msi_rcv_reg[0] = CVMX_NPI_NPI_MSI_RCV;
+#define INVALID_GENERATE_ADE 0x8700000000000000ULL;
+		msi_rcv_reg[1] = INVALID_GENERATE_ADE;
+		msi_rcv_reg[2] = INVALID_GENERATE_ADE;
+		msi_rcv_reg[3] = INVALID_GENERATE_ADE;
+		mis_ena_reg[0] = INVALID_GENERATE_ADE;
+		mis_ena_reg[1] = INVALID_GENERATE_ADE;
+		mis_ena_reg[2] = INVALID_GENERATE_ADE;
+		mis_ena_reg[3] = INVALID_GENERATE_ADE;
+		msi = &octeon_irq_chip_msi_pci;
+	}
+
+	for (irq = OCTEON_IRQ_MSI_BIT0; irq <= OCTEON_IRQ_MSI_LAST; irq++)
+		irq_set_chip_and_handler(irq, msi, handle_simple_irq);
+
+	if (octeon_has_feature(OCTEON_FEATURE_PCIE)) {
+		if (request_irq(OCTEON_IRQ_PCI_MSI0, octeon_msi_interrupt0,
+				0, "MSI[0:63]", octeon_msi_interrupt0))
+			panic("request_irq(OCTEON_IRQ_PCI_MSI0) failed");
+
+		if (request_irq(OCTEON_IRQ_PCI_MSI1, octeon_msi_interrupt1,
+				0, "MSI[64:127]", octeon_msi_interrupt1))
+			panic("request_irq(OCTEON_IRQ_PCI_MSI1) failed");
+
+		if (request_irq(OCTEON_IRQ_PCI_MSI2, octeon_msi_interrupt2,
+				0, "MSI[127:191]", octeon_msi_interrupt2))
+			panic("request_irq(OCTEON_IRQ_PCI_MSI2) failed");
+
+		if (request_irq(OCTEON_IRQ_PCI_MSI3, octeon_msi_interrupt3,
+				0, "MSI[192:255]", octeon_msi_interrupt3))
+			panic("request_irq(OCTEON_IRQ_PCI_MSI3) failed");
+
+		msi_irq_size = 256;
+	} else if (octeon_is_pci_host()) {
+		if (request_irq(OCTEON_IRQ_PCI_MSI0, octeon_msi_interrupt0,
+				0, "MSI[0:15]", octeon_msi_interrupt0))
+			panic("request_irq(OCTEON_IRQ_PCI_MSI0) failed");
+
+		if (request_irq(OCTEON_IRQ_PCI_MSI1, octeon_msi_interrupt0,
+				0, "MSI[16:31]", octeon_msi_interrupt0))
+			panic("request_irq(OCTEON_IRQ_PCI_MSI1) failed");
+
+		if (request_irq(OCTEON_IRQ_PCI_MSI2, octeon_msi_interrupt0,
+				0, "MSI[32:47]", octeon_msi_interrupt0))
+			panic("request_irq(OCTEON_IRQ_PCI_MSI2) failed");
+
+		if (request_irq(OCTEON_IRQ_PCI_MSI3, octeon_msi_interrupt0,
+				0, "MSI[48:63]", octeon_msi_interrupt0))
+			panic("request_irq(OCTEON_IRQ_PCI_MSI3) failed");
+		msi_irq_size = 64;
+	}
+	return 0;
+}
+subsys_initcall(octeon_msi_initialize);
diff --git a/arch/mips/pci/ops-bcm63xx.c b/arch/mips/pci/ops-bcm63xx.c
new file mode 100644
index 000000000..dc6dc2741
--- /dev/null
+++ b/arch/mips/pci/ops-bcm63xx.c
@@ -0,0 +1,528 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ */
+
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+
+#include "pci-bcm63xx.h"
+
+/*
+ * swizzle 32bits data to return only the needed part
+ */
+static int postprocess_read(u32 data, int where, unsigned int size)
+{
+	u32 ret;
+
+	ret = 0;
+	switch (size) {
+	case 1:
+		ret = (data >> ((where & 3) << 3)) & 0xff;
+		break;
+	case 2:
+		ret = (data >> ((where & 3) << 3)) & 0xffff;
+		break;
+	case 4:
+		ret = data;
+		break;
+	}
+	return ret;
+}
+
+static int preprocess_write(u32 orig_data, u32 val, int where,
+			    unsigned int size)
+{
+	u32 ret;
+
+	ret = 0;
+	switch (size) {
+	case 1:
+		ret = (orig_data & ~(0xff << ((where & 3) << 3))) |
+			(val << ((where & 3) << 3));
+		break;
+	case 2:
+		ret = (orig_data & ~(0xffff << ((where & 3) << 3))) |
+			(val << ((where & 3) << 3));
+		break;
+	case 4:
+		ret = val;
+		break;
+	}
+	return ret;
+}
+
+/*
+ * setup hardware for a configuration cycle with given parameters
+ */
+static int bcm63xx_setup_cfg_access(int type, unsigned int busn,
+				    unsigned int devfn, int where)
+{
+	unsigned int slot, func, reg;
+	u32 val;
+
+	slot = PCI_SLOT(devfn);
+	func = PCI_FUNC(devfn);
+	reg = where >> 2;
+
+	/* sanity check */
+	if (slot > (MPI_L2PCFG_DEVNUM_MASK >> MPI_L2PCFG_DEVNUM_SHIFT))
+		return 1;
+
+	if (func > (MPI_L2PCFG_FUNC_MASK >> MPI_L2PCFG_FUNC_SHIFT))
+		return 1;
+
+	if (reg > (MPI_L2PCFG_REG_MASK >> MPI_L2PCFG_REG_SHIFT))
+		return 1;
+
+	/* ok, setup config access */
+	val = (reg << MPI_L2PCFG_REG_SHIFT);
+	val |= (func << MPI_L2PCFG_FUNC_SHIFT);
+	val |= (slot << MPI_L2PCFG_DEVNUM_SHIFT);
+	val |= MPI_L2PCFG_CFG_USEREG_MASK;
+	val |= MPI_L2PCFG_CFG_SEL_MASK;
+	/* type 0 cycle for local bus, type 1 cycle for anything else */
+	if (type != 0) {
+		/* FIXME: how to specify bus ??? */
+		val |= (1 << MPI_L2PCFG_CFG_TYPE_SHIFT);
+	}
+	bcm_mpi_writel(val, MPI_L2PCFG_REG);
+
+	return 0;
+}
+
+static int bcm63xx_do_cfg_read(int type, unsigned int busn,
+				unsigned int devfn, int where, int size,
+				u32 *val)
+{
+	u32 data;
+
+	/* two phase cycle, first we write address, then read data at
+	 * another location, caller already has a spinlock so no need
+	 * to add one here  */
+	if (bcm63xx_setup_cfg_access(type, busn, devfn, where))
+		return PCIBIOS_DEVICE_NOT_FOUND;
+	iob();
+	data = le32_to_cpu(__raw_readl(pci_iospace_start));
+	/* restore IO space normal behaviour */
+	bcm_mpi_writel(0, MPI_L2PCFG_REG);
+
+	*val = postprocess_read(data, where, size);
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int bcm63xx_do_cfg_write(int type, unsigned int busn,
+				 unsigned int devfn, int where, int size,
+				 u32 val)
+{
+	u32 data;
+
+	/* two phase cycle, first we write address, then write data to
+	 * another location, caller already has a spinlock so no need
+	 * to add one here  */
+	if (bcm63xx_setup_cfg_access(type, busn, devfn, where))
+		return PCIBIOS_DEVICE_NOT_FOUND;
+	iob();
+
+	data = le32_to_cpu(__raw_readl(pci_iospace_start));
+	data = preprocess_write(data, val, where, size);
+
+	__raw_writel(cpu_to_le32(data), pci_iospace_start);
+	wmb();
+	/* no way to know the access is done, we have to wait */
+	udelay(500);
+	/* restore IO space normal behaviour */
+	bcm_mpi_writel(0, MPI_L2PCFG_REG);
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int bcm63xx_pci_read(struct pci_bus *bus, unsigned int devfn,
+			     int where, int size, u32 *val)
+{
+	int type;
+
+	type = bus->parent ? 1 : 0;
+
+	if (type == 0 && PCI_SLOT(devfn) == CARDBUS_PCI_IDSEL)
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	return bcm63xx_do_cfg_read(type, bus->number, devfn,
+				    where, size, val);
+}
+
+static int bcm63xx_pci_write(struct pci_bus *bus, unsigned int devfn,
+			      int where, int size, u32 val)
+{
+	int type;
+
+	type = bus->parent ? 1 : 0;
+
+	if (type == 0 && PCI_SLOT(devfn) == CARDBUS_PCI_IDSEL)
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	return bcm63xx_do_cfg_write(type, bus->number, devfn,
+				     where, size, val);
+}
+
+struct pci_ops bcm63xx_pci_ops = {
+	.read	= bcm63xx_pci_read,
+	.write	= bcm63xx_pci_write
+};
+
+#ifdef CONFIG_CARDBUS
+/*
+ * emulate configuration read access on a cardbus bridge
+ */
+#define FAKE_CB_BRIDGE_SLOT	0x1e
+
+static int fake_cb_bridge_bus_number = -1;
+
+static struct {
+	u16 pci_command;
+	u8 cb_latency;
+	u8 subordinate_busn;
+	u8 cardbus_busn;
+	u8 pci_busn;
+	int bus_assigned;
+	u16 bridge_control;
+
+	u32 mem_base0;
+	u32 mem_limit0;
+	u32 mem_base1;
+	u32 mem_limit1;
+
+	u32 io_base0;
+	u32 io_limit0;
+	u32 io_base1;
+	u32 io_limit1;
+} fake_cb_bridge_regs;
+
+static int fake_cb_bridge_read(int where, int size, u32 *val)
+{
+	unsigned int reg;
+	u32 data;
+
+	data = 0;
+	reg = where >> 2;
+	switch (reg) {
+	case (PCI_VENDOR_ID >> 2):
+	case (PCI_CB_SUBSYSTEM_VENDOR_ID >> 2):
+		/* create dummy vendor/device id from our cpu id */
+		data = (bcm63xx_get_cpu_id() << 16) | PCI_VENDOR_ID_BROADCOM;
+		break;
+
+	case (PCI_COMMAND >> 2):
+		data = (PCI_STATUS_DEVSEL_SLOW << 16);
+		data |= fake_cb_bridge_regs.pci_command;
+		break;
+
+	case (PCI_CLASS_REVISION >> 2):
+		data = (PCI_CLASS_BRIDGE_CARDBUS << 16);
+		break;
+
+	case (PCI_CACHE_LINE_SIZE >> 2):
+		data = (PCI_HEADER_TYPE_CARDBUS << 16);
+		break;
+
+	case (PCI_INTERRUPT_LINE >> 2):
+		/* bridge control */
+		data = (fake_cb_bridge_regs.bridge_control << 16);
+		/* pin:intA line:0xff */
+		data |= (0x1 << 8) | 0xff;
+		break;
+
+	case (PCI_CB_PRIMARY_BUS >> 2):
+		data = (fake_cb_bridge_regs.cb_latency << 24);
+		data |= (fake_cb_bridge_regs.subordinate_busn << 16);
+		data |= (fake_cb_bridge_regs.cardbus_busn << 8);
+		data |= fake_cb_bridge_regs.pci_busn;
+		break;
+
+	case (PCI_CB_MEMORY_BASE_0 >> 2):
+		data = fake_cb_bridge_regs.mem_base0;
+		break;
+
+	case (PCI_CB_MEMORY_LIMIT_0 >> 2):
+		data = fake_cb_bridge_regs.mem_limit0;
+		break;
+
+	case (PCI_CB_MEMORY_BASE_1 >> 2):
+		data = fake_cb_bridge_regs.mem_base1;
+		break;
+
+	case (PCI_CB_MEMORY_LIMIT_1 >> 2):
+		data = fake_cb_bridge_regs.mem_limit1;
+		break;
+
+	case (PCI_CB_IO_BASE_0 >> 2):
+		/* | 1 for 32bits io support */
+		data = fake_cb_bridge_regs.io_base0 | 0x1;
+		break;
+
+	case (PCI_CB_IO_LIMIT_0 >> 2):
+		data = fake_cb_bridge_regs.io_limit0;
+		break;
+
+	case (PCI_CB_IO_BASE_1 >> 2):
+		/* | 1 for 32bits io support */
+		data = fake_cb_bridge_regs.io_base1 | 0x1;
+		break;
+
+	case (PCI_CB_IO_LIMIT_1 >> 2):
+		data = fake_cb_bridge_regs.io_limit1;
+		break;
+	}
+
+	*val = postprocess_read(data, where, size);
+	return PCIBIOS_SUCCESSFUL;
+}
+
+/*
+ * emulate configuration write access on a cardbus bridge
+ */
+static int fake_cb_bridge_write(int where, int size, u32 val)
+{
+	unsigned int reg;
+	u32 data, tmp;
+	int ret;
+
+	ret = fake_cb_bridge_read((where & ~0x3), 4, &data);
+	if (ret != PCIBIOS_SUCCESSFUL)
+		return ret;
+
+	data = preprocess_write(data, val, where, size);
+
+	reg = where >> 2;
+	switch (reg) {
+	case (PCI_COMMAND >> 2):
+		fake_cb_bridge_regs.pci_command = (data & 0xffff);
+		break;
+
+	case (PCI_CB_PRIMARY_BUS >> 2):
+		fake_cb_bridge_regs.cb_latency = (data >> 24) & 0xff;
+		fake_cb_bridge_regs.subordinate_busn = (data >> 16) & 0xff;
+		fake_cb_bridge_regs.cardbus_busn = (data >> 8) & 0xff;
+		fake_cb_bridge_regs.pci_busn = data & 0xff;
+		if (fake_cb_bridge_regs.cardbus_busn)
+			fake_cb_bridge_regs.bus_assigned = 1;
+		break;
+
+	case (PCI_INTERRUPT_LINE >> 2):
+		tmp = (data >> 16) & 0xffff;
+		/* disable memory prefetch support */
+		tmp &= ~PCI_CB_BRIDGE_CTL_PREFETCH_MEM0;
+		tmp &= ~PCI_CB_BRIDGE_CTL_PREFETCH_MEM1;
+		fake_cb_bridge_regs.bridge_control = tmp;
+		break;
+
+	case (PCI_CB_MEMORY_BASE_0 >> 2):
+		fake_cb_bridge_regs.mem_base0 = data;
+		break;
+
+	case (PCI_CB_MEMORY_LIMIT_0 >> 2):
+		fake_cb_bridge_regs.mem_limit0 = data;
+		break;
+
+	case (PCI_CB_MEMORY_BASE_1 >> 2):
+		fake_cb_bridge_regs.mem_base1 = data;
+		break;
+
+	case (PCI_CB_MEMORY_LIMIT_1 >> 2):
+		fake_cb_bridge_regs.mem_limit1 = data;
+		break;
+
+	case (PCI_CB_IO_BASE_0 >> 2):
+		fake_cb_bridge_regs.io_base0 = data;
+		break;
+
+	case (PCI_CB_IO_LIMIT_0 >> 2):
+		fake_cb_bridge_regs.io_limit0 = data;
+		break;
+
+	case (PCI_CB_IO_BASE_1 >> 2):
+		fake_cb_bridge_regs.io_base1 = data;
+		break;
+
+	case (PCI_CB_IO_LIMIT_1 >> 2):
+		fake_cb_bridge_regs.io_limit1 = data;
+		break;
+	}
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int bcm63xx_cb_read(struct pci_bus *bus, unsigned int devfn,
+			   int where, int size, u32 *val)
+{
+	/* snoop access to slot 0x1e on root bus, we fake a cardbus
+	 * bridge at this location */
+	if (!bus->parent && PCI_SLOT(devfn) == FAKE_CB_BRIDGE_SLOT) {
+		fake_cb_bridge_bus_number = bus->number;
+		return fake_cb_bridge_read(where, size, val);
+	}
+
+	/* a  configuration  cycle for	the  device  behind the	 cardbus
+	 * bridge is  actually done as a  type 0 cycle	on the primary
+	 * bus. This means that only  one device can be on the cardbus
+	 * bus */
+	if (fake_cb_bridge_regs.bus_assigned &&
+	    bus->number == fake_cb_bridge_regs.cardbus_busn &&
+	    PCI_SLOT(devfn) == 0)
+		return bcm63xx_do_cfg_read(0, 0,
+					   PCI_DEVFN(CARDBUS_PCI_IDSEL, 0),
+					   where, size, val);
+
+	return PCIBIOS_DEVICE_NOT_FOUND;
+}
+
+static int bcm63xx_cb_write(struct pci_bus *bus, unsigned int devfn,
+			    int where, int size, u32 val)
+{
+	if (!bus->parent && PCI_SLOT(devfn) == FAKE_CB_BRIDGE_SLOT) {
+		fake_cb_bridge_bus_number = bus->number;
+		return fake_cb_bridge_write(where, size, val);
+	}
+
+	if (fake_cb_bridge_regs.bus_assigned &&
+	    bus->number == fake_cb_bridge_regs.cardbus_busn &&
+	    PCI_SLOT(devfn) == 0)
+		return bcm63xx_do_cfg_write(0, 0,
+					    PCI_DEVFN(CARDBUS_PCI_IDSEL, 0),
+					    where, size, val);
+
+	return PCIBIOS_DEVICE_NOT_FOUND;
+}
+
+struct pci_ops bcm63xx_cb_ops = {
+	.read	= bcm63xx_cb_read,
+	.write	 = bcm63xx_cb_write,
+};
+
+/*
+ * only one IO window, so it  cannot be shared by PCI and cardbus, use
+ * fixup to choose and detect unhandled configuration
+ */
+static void bcm63xx_fixup(struct pci_dev *dev)
+{
+	static int io_window = -1;
+	int i, found, new_io_window;
+	u32 val;
+
+	/* look for any io resource */
+	found = 0;
+	for (i = 0; i < DEVICE_COUNT_RESOURCE; i++) {
+		if (pci_resource_flags(dev, i) & IORESOURCE_IO) {
+			found = 1;
+			break;
+		}
+	}
+
+	if (!found)
+		return;
+
+	/* skip our fake bus with only cardbus bridge on it */
+	if (dev->bus->number == fake_cb_bridge_bus_number)
+		return;
+
+	/* find on which bus the device is */
+	if (fake_cb_bridge_regs.bus_assigned &&
+	    dev->bus->number == fake_cb_bridge_regs.cardbus_busn &&
+	    PCI_SLOT(dev->devfn) == 0)
+		new_io_window = 1;
+	else
+		new_io_window = 0;
+
+	if (new_io_window == io_window)
+		return;
+
+	if (io_window != -1) {
+		printk(KERN_ERR "bcm63xx: both PCI and cardbus devices "
+		       "need IO, which hardware cannot do\n");
+		return;
+	}
+
+	printk(KERN_INFO "bcm63xx: PCI IO window assigned to %s\n",
+	       (new_io_window == 0) ? "PCI" : "cardbus");
+
+	val = bcm_mpi_readl(MPI_L2PIOREMAP_REG);
+	if (io_window)
+		val |= MPI_L2PREMAP_IS_CARDBUS_MASK;
+	else
+		val &= ~MPI_L2PREMAP_IS_CARDBUS_MASK;
+	bcm_mpi_writel(val, MPI_L2PIOREMAP_REG);
+
+	io_window = new_io_window;
+}
+
+DECLARE_PCI_FIXUP_ENABLE(PCI_ANY_ID, PCI_ANY_ID, bcm63xx_fixup);
+#endif
+
+static int bcm63xx_pcie_can_access(struct pci_bus *bus, int devfn)
+{
+	switch (bus->number) {
+	case PCIE_BUS_BRIDGE:
+		return PCI_SLOT(devfn) == 0;
+	case PCIE_BUS_DEVICE:
+		if (PCI_SLOT(devfn) == 0)
+			return bcm_pcie_readl(PCIE_DLSTATUS_REG)
+					& DLSTATUS_PHYLINKUP;
+		fallthrough;
+	default:
+		return false;
+	}
+}
+
+static int bcm63xx_pcie_read(struct pci_bus *bus, unsigned int devfn,
+			     int where, int size, u32 *val)
+{
+	u32 data;
+	u32 reg = where & ~3;
+
+	if (!bcm63xx_pcie_can_access(bus, devfn))
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	if (bus->number == PCIE_BUS_DEVICE)
+		reg += PCIE_DEVICE_OFFSET;
+
+	data = bcm_pcie_readl(reg);
+
+	*val = postprocess_read(data, where, size);
+
+	return PCIBIOS_SUCCESSFUL;
+
+}
+
+static int bcm63xx_pcie_write(struct pci_bus *bus, unsigned int devfn,
+			      int where, int size, u32 val)
+{
+	u32 data;
+	u32 reg = where & ~3;
+
+	if (!bcm63xx_pcie_can_access(bus, devfn))
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	if (bus->number == PCIE_BUS_DEVICE)
+		reg += PCIE_DEVICE_OFFSET;
+
+
+	data = bcm_pcie_readl(reg);
+
+	data = preprocess_write(data, val, where, size);
+	bcm_pcie_writel(data, reg);
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+
+struct pci_ops bcm63xx_pcie_ops = {
+	.read	= bcm63xx_pcie_read,
+	.write	= bcm63xx_pcie_write
+};
diff --git a/arch/mips/pci/ops-bonito64.c b/arch/mips/pci/ops-bonito64.c
new file mode 100644
index 000000000..4d5fe614f
--- /dev/null
+++ b/arch/mips/pci/ops-bonito64.c
@@ -0,0 +1,148 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 1999, 2000, 2004  MIPS Technologies, Inc.
+ *	All rights reserved.
+ *	Authors: Carsten Langgaard <carstenl@mips.com>
+ *		 Maciej W. Rozycki <macro@mips.com>
+ *
+ * MIPS boards specific PCI support.
+ */
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+
+#include <asm/mips-boards/bonito64.h>
+
+#define PCI_ACCESS_READ	 0
+#define PCI_ACCESS_WRITE 1
+
+#define CFG_SPACE_REG(offset) (void *)CKSEG1ADDR(_pcictrl_bonito_pcicfg + (offset))
+#define ID_SEL_BEGIN 10
+#define MAX_DEV_NUM (31 - ID_SEL_BEGIN)
+
+
+static int bonito64_pcibios_config_access(unsigned char access_type,
+				      struct pci_bus *bus,
+				      unsigned int devfn, int where,
+				      u32 * data)
+{
+	u32 busnum = bus->number;
+	u32 addr, type;
+	u32 dummy;
+	void *addrp;
+	int device = PCI_SLOT(devfn);
+	int function = PCI_FUNC(devfn);
+	int reg = where & ~3;
+
+	if (busnum == 0) {
+		/* Type 0 configuration for onboard PCI bus */
+		if (device > MAX_DEV_NUM)
+			return -1;
+
+		addr = (1 << (device + ID_SEL_BEGIN)) | (function << 8) | reg;
+		type = 0;
+	} else {
+		/* Type 1 configuration for offboard PCI bus */
+		addr = (busnum << 16) | (device << 11) | (function << 8) | reg;
+		type = 0x10000;
+	}
+
+	/* Clear aborts */
+	BONITO_PCICMD |= BONITO_PCICMD_MABORT_CLR | BONITO_PCICMD_MTABORT_CLR;
+
+	BONITO_PCIMAP_CFG = (addr >> 16) | type;
+
+	/* Flush Bonito register block */
+	dummy = BONITO_PCIMAP_CFG;
+	mmiowb();
+
+	addrp = CFG_SPACE_REG(addr & 0xffff);
+	if (access_type == PCI_ACCESS_WRITE) {
+		writel(cpu_to_le32(*data), addrp);
+		/* Wait till done */
+		while (BONITO_PCIMSTAT & 0xF);
+	} else {
+		*data = le32_to_cpu(readl(addrp));
+	}
+
+	/* Detect Master/Target abort */
+	if (BONITO_PCICMD & (BONITO_PCICMD_MABORT_CLR |
+			     BONITO_PCICMD_MTABORT_CLR)) {
+		/* Error occurred */
+
+		/* Clear bits */
+		BONITO_PCICMD |= (BONITO_PCICMD_MABORT_CLR |
+				  BONITO_PCICMD_MTABORT_CLR);
+
+		return -1;
+	}
+
+	return 0;
+
+}
+
+
+/*
+ * We can't address 8 and 16 bit words directly.  Instead we have to
+ * read/write a 32bit word and mask/modify the data we actually want.
+ */
+static int bonito64_pcibios_read(struct pci_bus *bus, unsigned int devfn,
+			     int where, int size, u32 * val)
+{
+	u32 data = 0;
+
+	if ((size == 2) && (where & 1))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+	else if ((size == 4) && (where & 3))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+
+	if (bonito64_pcibios_config_access(PCI_ACCESS_READ, bus, devfn, where,
+				       &data))
+		return -1;
+
+	if (size == 1)
+		*val = (data >> ((where & 3) << 3)) & 0xff;
+	else if (size == 2)
+		*val = (data >> ((where & 3) << 3)) & 0xffff;
+	else
+		*val = data;
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int bonito64_pcibios_write(struct pci_bus *bus, unsigned int devfn,
+			      int where, int size, u32 val)
+{
+	u32 data = 0;
+
+	if ((size == 2) && (where & 1))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+	else if ((size == 4) && (where & 3))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+
+	if (size == 4)
+		data = val;
+	else {
+		if (bonito64_pcibios_config_access(PCI_ACCESS_READ, bus, devfn,
+					       where, &data))
+			return -1;
+
+		if (size == 1)
+			data = (data & ~(0xff << ((where & 3) << 3))) |
+				(val << ((where & 3) << 3));
+		else if (size == 2)
+			data = (data & ~(0xffff << ((where & 3) << 3))) |
+				(val << ((where & 3) << 3));
+	}
+
+	if (bonito64_pcibios_config_access(PCI_ACCESS_WRITE, bus, devfn, where,
+				       &data))
+		return -1;
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+struct pci_ops bonito64_pci_ops = {
+	.read = bonito64_pcibios_read,
+	.write = bonito64_pcibios_write
+};
diff --git a/arch/mips/pci/ops-gt64xxx_pci0.c b/arch/mips/pci/ops-gt64xxx_pci0.c
new file mode 100644
index 000000000..501dcdf5a
--- /dev/null
+++ b/arch/mips/pci/ops-gt64xxx_pci0.c
@@ -0,0 +1,140 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 1999, 2000, 2004  MIPS Technologies, Inc.
+ *	All rights reserved.
+ *	Authors: Carsten Langgaard <carstenl@mips.com>
+ *		 Maciej W. Rozycki <macro@mips.com>
+ */
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+
+#include <asm/gt64120.h>
+
+#define PCI_ACCESS_READ	 0
+#define PCI_ACCESS_WRITE 1
+
+/*
+ *  PCI configuration cycle AD bus definition
+ */
+/* Type 0 */
+#define PCI_CFG_TYPE0_REG_SHF		0
+#define PCI_CFG_TYPE0_FUNC_SHF		8
+
+/* Type 1 */
+#define PCI_CFG_TYPE1_REG_SHF		0
+#define PCI_CFG_TYPE1_FUNC_SHF		8
+#define PCI_CFG_TYPE1_DEV_SHF		11
+#define PCI_CFG_TYPE1_BUS_SHF		16
+
+static int gt64xxx_pci0_pcibios_config_access(unsigned char access_type,
+		struct pci_bus *bus, unsigned int devfn, int where, u32 * data)
+{
+	unsigned char busnum = bus->number;
+	u32 intr;
+
+	if ((busnum == 0) && (devfn >= PCI_DEVFN(31, 0)))
+		return -1;	/* Because of a bug in the galileo (for slot 31). */
+
+	/* Clear cause register bits */
+	GT_WRITE(GT_INTRCAUSE_OFS, ~(GT_INTRCAUSE_MASABORT0_BIT |
+				     GT_INTRCAUSE_TARABORT0_BIT));
+
+	/* Setup address */
+	GT_WRITE(GT_PCI0_CFGADDR_OFS,
+		 (busnum << GT_PCI0_CFGADDR_BUSNUM_SHF) |
+		 (devfn << GT_PCI0_CFGADDR_FUNCTNUM_SHF) |
+		 ((where / 4) << GT_PCI0_CFGADDR_REGNUM_SHF) |
+		 GT_PCI0_CFGADDR_CONFIGEN_BIT);
+
+	if (access_type == PCI_ACCESS_WRITE) {
+		if (busnum == 0 && PCI_SLOT(devfn) == 0) {
+			/*
+			 * The Galileo system controller is acting
+			 * differently than other devices.
+			 */
+			GT_WRITE(GT_PCI0_CFGDATA_OFS, *data);
+		} else
+			__GT_WRITE(GT_PCI0_CFGDATA_OFS, *data);
+	} else {
+		if (busnum == 0 && PCI_SLOT(devfn) == 0) {
+			/*
+			 * The Galileo system controller is acting
+			 * differently than other devices.
+			 */
+			*data = GT_READ(GT_PCI0_CFGDATA_OFS);
+		} else
+			*data = __GT_READ(GT_PCI0_CFGDATA_OFS);
+	}
+
+	/* Check for master or target abort */
+	intr = GT_READ(GT_INTRCAUSE_OFS);
+
+	if (intr & (GT_INTRCAUSE_MASABORT0_BIT | GT_INTRCAUSE_TARABORT0_BIT)) {
+		/* Error occurred */
+
+		/* Clear bits */
+		GT_WRITE(GT_INTRCAUSE_OFS, ~(GT_INTRCAUSE_MASABORT0_BIT |
+					     GT_INTRCAUSE_TARABORT0_BIT));
+
+		return -1;
+	}
+
+	return 0;
+}
+
+
+/*
+ * We can't address 8 and 16 bit words directly.  Instead we have to
+ * read/write a 32bit word and mask/modify the data we actually want.
+ */
+static int gt64xxx_pci0_pcibios_read(struct pci_bus *bus, unsigned int devfn,
+		int where, int size, u32 * val)
+{
+	u32 data = 0;
+
+	if (gt64xxx_pci0_pcibios_config_access(PCI_ACCESS_READ, bus, devfn,
+					       where, &data))
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	if (size == 1)
+		*val = (data >> ((where & 3) << 3)) & 0xff;
+	else if (size == 2)
+		*val = (data >> ((where & 3) << 3)) & 0xffff;
+	else
+		*val = data;
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int gt64xxx_pci0_pcibios_write(struct pci_bus *bus, unsigned int devfn,
+		int where, int size, u32 val)
+{
+	u32 data = 0;
+
+	if (size == 4)
+		data = val;
+	else {
+		if (gt64xxx_pci0_pcibios_config_access(PCI_ACCESS_READ, bus,
+						       devfn, where, &data))
+			return PCIBIOS_DEVICE_NOT_FOUND;
+
+		if (size == 1)
+			data = (data & ~(0xff << ((where & 3) << 3))) |
+				(val << ((where & 3) << 3));
+		else if (size == 2)
+			data = (data & ~(0xffff << ((where & 3) << 3))) |
+				(val << ((where & 3) << 3));
+	}
+
+	if (gt64xxx_pci0_pcibios_config_access(PCI_ACCESS_WRITE, bus, devfn,
+					       where, &data))
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+struct pci_ops gt64xxx_pci0_ops = {
+	.read	= gt64xxx_pci0_pcibios_read,
+	.write	= gt64xxx_pci0_pcibios_write
+};
diff --git a/arch/mips/pci/ops-lantiq.c b/arch/mips/pci/ops-lantiq.c
new file mode 100644
index 000000000..7d7135539
--- /dev/null
+++ b/arch/mips/pci/ops-lantiq.c
@@ -0,0 +1,113 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ *  Copyright (C) 2010 John Crispin <john@phrozen.org>
+ */
+
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/mm.h>
+#include <asm/addrspace.h>
+#include <linux/vmalloc.h>
+
+#include <lantiq_soc.h>
+
+#include "pci-lantiq.h"
+
+#define LTQ_PCI_CFG_BUSNUM_SHF 16
+#define LTQ_PCI_CFG_DEVNUM_SHF 11
+#define LTQ_PCI_CFG_FUNNUM_SHF 8
+
+#define PCI_ACCESS_READ	 0
+#define PCI_ACCESS_WRITE 1
+
+static int ltq_pci_config_access(unsigned char access_type, struct pci_bus *bus,
+	unsigned int devfn, unsigned int where, u32 *data)
+{
+	unsigned long cfg_base;
+	unsigned long flags;
+	u32 temp;
+
+	/* we support slot from 0 to 15 dev_fn & 0x68 (AD29) is the
+	   SoC itself */
+	if ((bus->number != 0) || ((devfn & 0xf8) > 0x78)
+		|| ((devfn & 0xf8) == 0) || ((devfn & 0xf8) == 0x68))
+		return 1;
+
+	spin_lock_irqsave(&ebu_lock, flags);
+
+	cfg_base = (unsigned long) ltq_pci_mapped_cfg;
+	cfg_base |= (bus->number << LTQ_PCI_CFG_BUSNUM_SHF) | (devfn <<
+			LTQ_PCI_CFG_FUNNUM_SHF) | (where & ~0x3);
+
+	/* Perform access */
+	if (access_type == PCI_ACCESS_WRITE) {
+		ltq_w32(swab32(*data), ((u32 *)cfg_base));
+	} else {
+		*data = ltq_r32(((u32 *)(cfg_base)));
+		*data = swab32(*data);
+	}
+	wmb();
+
+	/* clean possible Master abort */
+	cfg_base = (unsigned long) ltq_pci_mapped_cfg;
+	cfg_base |= (0x0 << LTQ_PCI_CFG_FUNNUM_SHF) + 4;
+	temp = ltq_r32(((u32 *)(cfg_base)));
+	temp = swab32(temp);
+	cfg_base = (unsigned long) ltq_pci_mapped_cfg;
+	cfg_base |= (0x68 << LTQ_PCI_CFG_FUNNUM_SHF) + 4;
+	ltq_w32(temp, ((u32 *)cfg_base));
+
+	spin_unlock_irqrestore(&ebu_lock, flags);
+
+	if (((*data) == 0xffffffff) && (access_type == PCI_ACCESS_READ))
+		return 1;
+
+	return 0;
+}
+
+int ltq_pci_read_config_dword(struct pci_bus *bus, unsigned int devfn,
+	int where, int size, u32 *val)
+{
+	u32 data = 0;
+
+	if (ltq_pci_config_access(PCI_ACCESS_READ, bus, devfn, where, &data))
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	if (size == 1)
+		*val = (data >> ((where & 3) << 3)) & 0xff;
+	else if (size == 2)
+		*val = (data >> ((where & 3) << 3)) & 0xffff;
+	else
+		*val = data;
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+int ltq_pci_write_config_dword(struct pci_bus *bus, unsigned int devfn,
+	int where, int size, u32 val)
+{
+	u32 data = 0;
+
+	if (size == 4) {
+		data = val;
+	} else {
+		if (ltq_pci_config_access(PCI_ACCESS_READ, bus,
+				devfn, where, &data))
+			return PCIBIOS_DEVICE_NOT_FOUND;
+
+		if (size == 1)
+			data = (data & ~(0xff << ((where & 3) << 3))) |
+				(val << ((where & 3) << 3));
+		else if (size == 2)
+			data = (data & ~(0xffff << ((where & 3) << 3))) |
+				(val << ((where & 3) << 3));
+	}
+
+	if (ltq_pci_config_access(PCI_ACCESS_WRITE, bus, devfn, where, &data))
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	return PCIBIOS_SUCCESSFUL;
+}
diff --git a/arch/mips/pci/ops-loongson2.c b/arch/mips/pci/ops-loongson2.c
new file mode 100644
index 000000000..0d1b36ba1
--- /dev/null
+++ b/arch/mips/pci/ops-loongson2.c
@@ -0,0 +1,213 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 1999, 2000, 2004  MIPS Technologies, Inc.
+ *	All rights reserved.
+ *	Authors: Carsten Langgaard <carstenl@mips.com>
+ *		 Maciej W. Rozycki <macro@mips.com>
+ *
+ * Copyright (C) 2009 Lemote Inc.
+ * Author: Wu Zhangjin <wuzhangjin@gmail.com>
+ */
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/export.h>
+
+#include <loongson.h>
+
+#ifdef CONFIG_CS5536
+#include <cs5536/cs5536_pci.h>
+#include <cs5536/cs5536.h>
+#endif
+
+#define PCI_ACCESS_READ	 0
+#define PCI_ACCESS_WRITE 1
+
+#define CFG_SPACE_REG(offset) \
+	(void *)CKSEG1ADDR(LOONGSON_PCICFG_BASE | (offset))
+#define ID_SEL_BEGIN 11
+#define MAX_DEV_NUM (31 - ID_SEL_BEGIN)
+
+
+static int loongson_pcibios_config_access(unsigned char access_type,
+				      struct pci_bus *bus,
+				      unsigned int devfn, int where,
+				      u32 *data)
+{
+	u32 busnum = bus->number;
+	u32 addr, type;
+	u32 dummy;
+	void *addrp;
+	int device = PCI_SLOT(devfn);
+	int function = PCI_FUNC(devfn);
+	int reg = where & ~3;
+
+	if (busnum == 0) {
+		/* board-specific part,currently,only fuloong2f,yeeloong2f
+		 * use CS5536, fuloong2e use via686b, gdium has no
+		 * south bridge
+		 */
+#ifdef CONFIG_CS5536
+		/* cs5536_pci_conf_read4/write4() will call _rdmsr/_wrmsr() to
+		 * access the regsters PCI_MSR_ADDR, PCI_MSR_DATA_LO,
+		 * PCI_MSR_DATA_HI, which is bigger than PCI_MSR_CTRL, so, it
+		 * will not go this branch, but the others. so, no calling dead
+		 * loop here.
+		 */
+		if ((PCI_IDSEL_CS5536 == device) && (reg < PCI_MSR_CTRL)) {
+			switch (access_type) {
+			case PCI_ACCESS_READ:
+				*data = cs5536_pci_conf_read4(function, reg);
+				break;
+			case PCI_ACCESS_WRITE:
+				cs5536_pci_conf_write4(function, reg, *data);
+				break;
+			}
+			return 0;
+		}
+#endif
+		/* Type 0 configuration for onboard PCI bus */
+		if (device > MAX_DEV_NUM)
+			return -1;
+
+		addr = (1 << (device + ID_SEL_BEGIN)) | (function << 8) | reg;
+		type = 0;
+	} else {
+		/* Type 1 configuration for offboard PCI bus */
+		addr = (busnum << 16) | (device << 11) | (function << 8) | reg;
+		type = 0x10000;
+	}
+
+	/* Clear aborts */
+	LOONGSON_PCICMD |= LOONGSON_PCICMD_MABORT_CLR | \
+				LOONGSON_PCICMD_MTABORT_CLR;
+
+	LOONGSON_PCIMAP_CFG = (addr >> 16) | type;
+
+	/* Flush Bonito register block */
+	dummy = LOONGSON_PCIMAP_CFG;
+	mmiowb();
+
+	addrp = CFG_SPACE_REG(addr & 0xffff);
+	if (access_type == PCI_ACCESS_WRITE)
+		writel(cpu_to_le32(*data), addrp);
+	else
+		*data = le32_to_cpu(readl(addrp));
+
+	/* Detect Master/Target abort */
+	if (LOONGSON_PCICMD & (LOONGSON_PCICMD_MABORT_CLR |
+			     LOONGSON_PCICMD_MTABORT_CLR)) {
+		/* Error occurred */
+
+		/* Clear bits */
+		LOONGSON_PCICMD |= (LOONGSON_PCICMD_MABORT_CLR |
+				  LOONGSON_PCICMD_MTABORT_CLR);
+
+		return -1;
+	}
+
+	return 0;
+
+}
+
+
+/*
+ * We can't address 8 and 16 bit words directly.  Instead we have to
+ * read/write a 32bit word and mask/modify the data we actually want.
+ */
+static int loongson_pcibios_read(struct pci_bus *bus, unsigned int devfn,
+			     int where, int size, u32 *val)
+{
+	u32 data = 0;
+
+	if ((size == 2) && (where & 1))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+	else if ((size == 4) && (where & 3))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+
+	if (loongson_pcibios_config_access(PCI_ACCESS_READ, bus, devfn, where,
+				       &data))
+		return -1;
+
+	if (size == 1)
+		*val = (data >> ((where & 3) << 3)) & 0xff;
+	else if (size == 2)
+		*val = (data >> ((where & 3) << 3)) & 0xffff;
+	else
+		*val = data;
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int loongson_pcibios_write(struct pci_bus *bus, unsigned int devfn,
+			      int where, int size, u32 val)
+{
+	u32 data = 0;
+
+	if ((size == 2) && (where & 1))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+	else if ((size == 4) && (where & 3))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+
+	if (size == 4)
+		data = val;
+	else {
+		if (loongson_pcibios_config_access(PCI_ACCESS_READ, bus, devfn,
+					where, &data))
+			return -1;
+
+		if (size == 1)
+			data = (data & ~(0xff << ((where & 3) << 3))) |
+				(val << ((where & 3) << 3));
+		else if (size == 2)
+			data = (data & ~(0xffff << ((where & 3) << 3))) |
+				(val << ((where & 3) << 3));
+	}
+
+	if (loongson_pcibios_config_access(PCI_ACCESS_WRITE, bus, devfn, where,
+				       &data))
+		return -1;
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+struct pci_ops loongson_pci_ops = {
+	.read = loongson_pcibios_read,
+	.write = loongson_pcibios_write
+};
+
+#ifdef CONFIG_CS5536
+DEFINE_RAW_SPINLOCK(msr_lock);
+
+void _rdmsr(u32 msr, u32 *hi, u32 *lo)
+{
+	struct pci_bus bus = {
+		.number = PCI_BUS_CS5536
+	};
+	u32 devfn = PCI_DEVFN(PCI_IDSEL_CS5536, 0);
+	unsigned long flags;
+
+	raw_spin_lock_irqsave(&msr_lock, flags);
+	loongson_pcibios_write(&bus, devfn, PCI_MSR_ADDR, 4, msr);
+	loongson_pcibios_read(&bus, devfn, PCI_MSR_DATA_LO, 4, lo);
+	loongson_pcibios_read(&bus, devfn, PCI_MSR_DATA_HI, 4, hi);
+	raw_spin_unlock_irqrestore(&msr_lock, flags);
+}
+EXPORT_SYMBOL(_rdmsr);
+
+void _wrmsr(u32 msr, u32 hi, u32 lo)
+{
+	struct pci_bus bus = {
+		.number = PCI_BUS_CS5536
+	};
+	u32 devfn = PCI_DEVFN(PCI_IDSEL_CS5536, 0);
+	unsigned long flags;
+
+	raw_spin_lock_irqsave(&msr_lock, flags);
+	loongson_pcibios_write(&bus, devfn, PCI_MSR_ADDR, 4, msr);
+	loongson_pcibios_write(&bus, devfn, PCI_MSR_DATA_LO, 4, lo);
+	loongson_pcibios_write(&bus, devfn, PCI_MSR_DATA_HI, 4, hi);
+	raw_spin_unlock_irqrestore(&msr_lock, flags);
+}
+EXPORT_SYMBOL(_wrmsr);
+#endif
diff --git a/arch/mips/pci/ops-mace.c b/arch/mips/pci/ops-mace.c
new file mode 100644
index 000000000..951d8070f
--- /dev/null
+++ b/arch/mips/pci/ops-mace.c
@@ -0,0 +1,100 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2000, 2001 Keith M Wesolowski
+ */
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/types.h>
+#include <asm/ip32/mace.h>
+
+#if 0
+# define DPRINTK(args...) printk(args);
+#else
+# define DPRINTK(args...)
+#endif
+
+/*
+ * O2 has up to 5 PCI devices connected into the MACE bridge.  The device
+ * map looks like this:
+ *
+ * 0  aic7xxx 0
+ * 1  aic7xxx 1
+ * 2  expansion slot
+ * 3  N/C
+ * 4  N/C
+ */
+
+static inline int mkaddr(struct pci_bus *bus, unsigned int devfn,
+	unsigned int reg)
+{
+	return ((bus->number & 0xff) << 16) |
+		((devfn & 0xff) << 8) |
+		(reg & 0xfc);
+}
+
+
+static int
+mace_pci_read_config(struct pci_bus *bus, unsigned int devfn,
+		     int reg, int size, u32 *val)
+{
+	u32 control = mace->pci.control;
+
+	/* disable master aborts interrupts during config read */
+	mace->pci.control = control & ~MACEPCI_CONTROL_MAR_INT;
+	mace->pci.config_addr = mkaddr(bus, devfn, reg);
+	switch (size) {
+	case 1:
+		*val = mace->pci.config_data.b[(reg & 3) ^ 3];
+		break;
+	case 2:
+		*val = mace->pci.config_data.w[((reg >> 1) & 1) ^ 1];
+		break;
+	case 4:
+		*val = mace->pci.config_data.l;
+		break;
+	}
+	/* ack possible master abort */
+	mace->pci.error &= ~MACEPCI_ERROR_MASTER_ABORT;
+	mace->pci.control = control;
+	/*
+	 * someone forgot to set the ultra bit for the onboard
+	 * scsi chips; we fake it here
+	 */
+	if (bus->number == 0 && reg == 0x40 && size == 4 &&
+	    (devfn == (1 << 3) || devfn == (2 << 3)))
+		*val |= 0x1000;
+
+	DPRINTK("read%d: reg=%08x,val=%02x\n", size * 8, reg, *val);
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int
+mace_pci_write_config(struct pci_bus *bus, unsigned int devfn,
+		      int reg, int size, u32 val)
+{
+	mace->pci.config_addr = mkaddr(bus, devfn, reg);
+	switch (size) {
+	case 1:
+		mace->pci.config_data.b[(reg & 3) ^ 3] = val;
+		break;
+	case 2:
+		mace->pci.config_data.w[((reg >> 1) & 1) ^ 1] = val;
+		break;
+	case 4:
+		mace->pci.config_data.l = val;
+		break;
+	}
+
+	DPRINTK("write%d: reg=%08x,val=%02x\n", size * 8, reg, val);
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+struct pci_ops mace_pci_ops = {
+	.read = mace_pci_read_config,
+	.write = mace_pci_write_config,
+};
diff --git a/arch/mips/pci/ops-msc.c b/arch/mips/pci/ops-msc.c
new file mode 100644
index 000000000..1f438baaf
--- /dev/null
+++ b/arch/mips/pci/ops-msc.c
@@ -0,0 +1,134 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 1999, 2000, 2004, 2005	 MIPS Technologies, Inc.
+ *    All rights reserved.
+ *    Authors: Carsten Langgaard <carstenl@mips.com>
+ *	       Maciej W. Rozycki <macro@mips.com>
+ * Copyright (C) 2005 Ralf Baechle (ralf@linux-mips.org)
+ *
+ * MIPS boards specific PCI support.
+ */
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+
+#include <asm/mips-boards/msc01_pci.h>
+
+#define PCI_ACCESS_READ	 0
+#define PCI_ACCESS_WRITE 1
+
+/*
+ *  PCI configuration cycle AD bus definition
+ */
+/* Type 0 */
+#define PCI_CFG_TYPE0_REG_SHF		0
+#define PCI_CFG_TYPE0_FUNC_SHF		8
+
+/* Type 1 */
+#define PCI_CFG_TYPE1_REG_SHF		0
+#define PCI_CFG_TYPE1_FUNC_SHF		8
+#define PCI_CFG_TYPE1_DEV_SHF		11
+#define PCI_CFG_TYPE1_BUS_SHF		16
+
+static int msc_pcibios_config_access(unsigned char access_type,
+	struct pci_bus *bus, unsigned int devfn, int where, u32 * data)
+{
+	unsigned char busnum = bus->number;
+	u32 intr;
+
+	/* Clear status register bits. */
+	MSC_WRITE(MSC01_PCI_INTSTAT,
+		  (MSC01_PCI_INTCFG_MA_BIT | MSC01_PCI_INTCFG_TA_BIT));
+
+	MSC_WRITE(MSC01_PCI_CFGADDR,
+		  ((busnum << MSC01_PCI_CFGADDR_BNUM_SHF) |
+		   (PCI_SLOT(devfn) << MSC01_PCI_CFGADDR_DNUM_SHF) |
+		   (PCI_FUNC(devfn) << MSC01_PCI_CFGADDR_FNUM_SHF) |
+		   ((where / 4) << MSC01_PCI_CFGADDR_RNUM_SHF)));
+
+	/* Perform access */
+	if (access_type == PCI_ACCESS_WRITE)
+		MSC_WRITE(MSC01_PCI_CFGDATA, *data);
+	else
+		MSC_READ(MSC01_PCI_CFGDATA, *data);
+
+	/* Detect Master/Target abort */
+	MSC_READ(MSC01_PCI_INTSTAT, intr);
+	if (intr & (MSC01_PCI_INTCFG_MA_BIT | MSC01_PCI_INTCFG_TA_BIT)) {
+		/* Error occurred */
+
+		/* Clear bits */
+		MSC_WRITE(MSC01_PCI_INTSTAT,
+			  (MSC01_PCI_INTCFG_MA_BIT | MSC01_PCI_INTCFG_TA_BIT));
+
+		return -1;
+	}
+
+	return 0;
+}
+
+
+/*
+ * We can't address 8 and 16 bit words directly.  Instead we have to
+ * read/write a 32bit word and mask/modify the data we actually want.
+ */
+static int msc_pcibios_read(struct pci_bus *bus, unsigned int devfn,
+			     int where, int size, u32 * val)
+{
+	u32 data = 0;
+
+	if ((size == 2) && (where & 1))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+	else if ((size == 4) && (where & 3))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+
+	if (msc_pcibios_config_access(PCI_ACCESS_READ, bus, devfn, where,
+				      &data))
+		return -1;
+
+	if (size == 1)
+		*val = (data >> ((where & 3) << 3)) & 0xff;
+	else if (size == 2)
+		*val = (data >> ((where & 3) << 3)) & 0xffff;
+	else
+		*val = data;
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int msc_pcibios_write(struct pci_bus *bus, unsigned int devfn,
+			      int where, int size, u32 val)
+{
+	u32 data = 0;
+
+	if ((size == 2) && (where & 1))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+	else if ((size == 4) && (where & 3))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+
+	if (size == 4)
+		data = val;
+	else {
+		if (msc_pcibios_config_access(PCI_ACCESS_READ, bus, devfn,
+					      where, &data))
+			return -1;
+
+		if (size == 1)
+			data = (data & ~(0xff << ((where & 3) << 3))) |
+				(val << ((where & 3) << 3));
+		else if (size == 2)
+			data = (data & ~(0xffff << ((where & 3) << 3))) |
+				(val << ((where & 3) << 3));
+	}
+
+	if (msc_pcibios_config_access(PCI_ACCESS_WRITE, bus, devfn, where,
+				       &data))
+		return -1;
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+struct pci_ops msc_pci_ops = {
+	.read = msc_pcibios_read,
+	.write = msc_pcibios_write
+};
diff --git a/arch/mips/pci/ops-rc32434.c b/arch/mips/pci/ops-rc32434.c
new file mode 100644
index 000000000..874ed6df9
--- /dev/null
+++ b/arch/mips/pci/ops-rc32434.c
@@ -0,0 +1,206 @@
+/*
+ *  BRIEF MODULE DESCRIPTION
+ *     pci_ops for IDT EB434 board
+ *
+ *  Copyright 2004 IDT Inc. (rischelp@idt.com)
+ *  Copyright 2006 Felix Fietkau <nbd@openwrt.org>
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/pci.h>
+#include <linux/types.h>
+
+#include <asm/cpu.h>
+#include <asm/mach-rc32434/rc32434.h>
+#include <asm/mach-rc32434/pci.h>
+
+#define PCI_ACCESS_READ	 0
+#define PCI_ACCESS_WRITE 1
+
+
+#define PCI_CFG_SET(bus, slot, func, off) \
+	(rc32434_pci->pcicfga = (0x80000000 | \
+				((bus) << 16) | ((slot)<<11) | \
+				((func)<<8) | (off)))
+
+static inline int config_access(unsigned char access_type,
+				struct pci_bus *bus, unsigned int devfn,
+				unsigned char where, u32 *data)
+{
+	unsigned int slot = PCI_SLOT(devfn);
+	u8 func = PCI_FUNC(devfn);
+
+	/* Setup address */
+	PCI_CFG_SET(bus->number, slot, func, where);
+	rc32434_sync();
+
+	if (access_type == PCI_ACCESS_WRITE)
+		rc32434_pci->pcicfgd = *data;
+	else
+		*data = rc32434_pci->pcicfgd;
+
+	rc32434_sync();
+
+	return 0;
+}
+
+
+/*
+ * We can't address 8 and 16 bit words directly.  Instead we have to
+ * read/write a 32bit word and mask/modify the data we actually want.
+ */
+static int read_config_byte(struct pci_bus *bus, unsigned int devfn,
+			    int where, u8 *val)
+{
+	u32 data;
+	int ret;
+
+	ret = config_access(PCI_ACCESS_READ, bus, devfn, where, &data);
+	*val = (data >> ((where & 3) << 3)) & 0xff;
+	return ret;
+}
+
+static int read_config_word(struct pci_bus *bus, unsigned int devfn,
+			    int where, u16 *val)
+{
+	u32 data;
+	int ret;
+
+	ret = config_access(PCI_ACCESS_READ, bus, devfn, where, &data);
+	*val = (data >> ((where & 3) << 3)) & 0xffff;
+	return ret;
+}
+
+static int read_config_dword(struct pci_bus *bus, unsigned int devfn,
+			     int where, u32 *val)
+{
+	int ret;
+	int delay = 1;
+
+	/*
+	 * Don't scan too far, else there will be errors with plugged in
+	 * daughterboard (rb564).
+	 */
+	if (bus->number == 0 && PCI_SLOT(devfn) > 21)
+		return 0;
+
+retry:
+	ret = config_access(PCI_ACCESS_READ, bus, devfn, where, val);
+
+	/*
+	 * Certain devices react delayed at device scan time, this
+	 * gives them time to settle
+	 */
+	if (where == PCI_VENDOR_ID) {
+		if (ret == 0xffffffff || ret == 0x00000000 ||
+		    ret == 0x0000ffff || ret == 0xffff0000) {
+			if (delay > 4)
+				return 0;
+			delay *= 2;
+			msleep(delay);
+			goto retry;
+		}
+	}
+
+	return ret;
+}
+
+static int
+write_config_byte(struct pci_bus *bus, unsigned int devfn, int where,
+		  u8 val)
+{
+	u32 data = 0;
+
+	if (config_access(PCI_ACCESS_READ, bus, devfn, where, &data))
+		return -1;
+
+	data = (data & ~(0xff << ((where & 3) << 3))) |
+	    (val << ((where & 3) << 3));
+
+	if (config_access(PCI_ACCESS_WRITE, bus, devfn, where, &data))
+		return -1;
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+
+static int
+write_config_word(struct pci_bus *bus, unsigned int devfn, int where,
+		  u16 val)
+{
+	u32 data = 0;
+
+	if (config_access(PCI_ACCESS_READ, bus, devfn, where, &data))
+		return -1;
+
+	data = (data & ~(0xffff << ((where & 3) << 3))) |
+	    (val << ((where & 3) << 3));
+
+	if (config_access(PCI_ACCESS_WRITE, bus, devfn, where, &data))
+		return -1;
+
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+
+static int
+write_config_dword(struct pci_bus *bus, unsigned int devfn, int where,
+		   u32 val)
+{
+	if (config_access(PCI_ACCESS_WRITE, bus, devfn, where, &val))
+		return -1;
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int pci_config_read(struct pci_bus *bus, unsigned int devfn,
+			   int where, int size, u32 *val)
+{
+	switch (size) {
+	case 1:
+		return read_config_byte(bus, devfn, where, (u8 *) val);
+	case 2:
+		return read_config_word(bus, devfn, where, (u16 *) val);
+	default:
+		return read_config_dword(bus, devfn, where, val);
+	}
+}
+
+static int pci_config_write(struct pci_bus *bus, unsigned int devfn,
+			    int where, int size, u32 val)
+{
+	switch (size) {
+	case 1:
+		return write_config_byte(bus, devfn, where, (u8) val);
+	case 2:
+		return write_config_word(bus, devfn, where, (u16) val);
+	default:
+		return write_config_dword(bus, devfn, where, val);
+	}
+}
+
+struct pci_ops rc32434_pci_ops = {
+	.read = pci_config_read,
+	.write = pci_config_write,
+};
diff --git a/arch/mips/pci/ops-sni.c b/arch/mips/pci/ops-sni.c
new file mode 100644
index 000000000..35daa7fe6
--- /dev/null
+++ b/arch/mips/pci/ops-sni.c
@@ -0,0 +1,164 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * SNI specific PCI support for RM200/RM300.
+ *
+ * Copyright (C) 1997 - 2000, 2003 Ralf Baechle <ralf@linux-mips.org>
+ */
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/types.h>
+#include <asm/sni.h>
+
+/*
+ * It seems that on the RM200 only lower 3 bits of the 5 bit PCI device
+ * address are decoded.	 We therefore manually have to reject attempts at
+ * reading outside this range.	Being on the paranoid side we only do this
+ * test for bus 0 and hope forwarding and decoding work properly for any
+ * subordinated busses.
+ *
+ * ASIC PCI only supports type 1 config cycles.
+ */
+static int set_config_address(unsigned int busno, unsigned int devfn, int reg)
+{
+	if ((devfn > 255) || (reg > 255))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+
+	if (busno == 0 && devfn >= PCI_DEVFN(8, 0))
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	*(volatile u32 *)PCIMT_CONFIG_ADDRESS =
+		 ((busno    & 0xff) << 16) |
+		 ((devfn    & 0xff) <<	8) |
+		  (reg	    & 0xfc);
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int pcimt_read(struct pci_bus *bus, unsigned int devfn, int reg,
+		      int size, u32 * val)
+{
+	int res;
+
+	if ((res = set_config_address(bus->number, devfn, reg)))
+		return res;
+
+	switch (size) {
+	case 1:
+		*val = inb(PCIMT_CONFIG_DATA + (reg & 3));
+		break;
+	case 2:
+		*val = inw(PCIMT_CONFIG_DATA + (reg & 2));
+		break;
+	case 4:
+		*val = inl(PCIMT_CONFIG_DATA);
+		break;
+	}
+
+	return 0;
+}
+
+static int pcimt_write(struct pci_bus *bus, unsigned int devfn, int reg,
+		       int size, u32 val)
+{
+	int res;
+
+	if ((res = set_config_address(bus->number, devfn, reg)))
+		return res;
+
+	switch (size) {
+	case 1:
+		outb(val, PCIMT_CONFIG_DATA + (reg & 3));
+		break;
+	case 2:
+		outw(val, PCIMT_CONFIG_DATA + (reg & 2));
+		break;
+	case 4:
+		outl(val, PCIMT_CONFIG_DATA);
+		break;
+	}
+
+	return 0;
+}
+
+struct pci_ops sni_pcimt_ops = {
+	.read = pcimt_read,
+	.write = pcimt_write,
+};
+
+static int pcit_set_config_address(unsigned int busno, unsigned int devfn, int reg)
+{
+	if ((devfn > 255) || (reg > 255) || (busno > 255))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+
+	outl((1 << 31) | ((busno & 0xff) << 16) | ((devfn & 0xff) << 8) | (reg & 0xfc), 0xcf8);
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int pcit_read(struct pci_bus *bus, unsigned int devfn, int reg,
+		      int size, u32 * val)
+{
+	int res;
+
+	/*
+	 * on bus 0 we need to check, whether there is a device answering
+	 * for the devfn by doing a config write and checking the result. If
+	 * we don't do it, we will get a data bus error
+	 */
+	if (bus->number == 0) {
+		pcit_set_config_address(0, 0, 0x68);
+		outl(inl(0xcfc) | 0xc0000000, 0xcfc);
+		if ((res = pcit_set_config_address(0, devfn, 0)))
+			return res;
+		outl(0xffffffff, 0xcfc);
+		pcit_set_config_address(0, 0, 0x68);
+		if (inl(0xcfc) & 0x100000)
+			return PCIBIOS_DEVICE_NOT_FOUND;
+	}
+	if ((res = pcit_set_config_address(bus->number, devfn, reg)))
+		return res;
+
+	switch (size) {
+	case 1:
+		*val = inb(PCIMT_CONFIG_DATA + (reg & 3));
+		break;
+	case 2:
+		*val = inw(PCIMT_CONFIG_DATA + (reg & 2));
+		break;
+	case 4:
+		*val = inl(PCIMT_CONFIG_DATA);
+		break;
+	}
+	return 0;
+}
+
+static int pcit_write(struct pci_bus *bus, unsigned int devfn, int reg,
+		       int size, u32 val)
+{
+	int res;
+
+	if ((res = pcit_set_config_address(bus->number, devfn, reg)))
+		return res;
+
+	switch (size) {
+	case 1:
+		outb(val, PCIMT_CONFIG_DATA + (reg & 3));
+		break;
+	case 2:
+		outw(val, PCIMT_CONFIG_DATA + (reg & 2));
+		break;
+	case 4:
+		outl(val, PCIMT_CONFIG_DATA);
+		break;
+	}
+
+	return 0;
+}
+
+
+struct pci_ops sni_pcit_ops = {
+	.read = pcit_read,
+	.write = pcit_write,
+};
diff --git a/arch/mips/pci/ops-tx4927.c b/arch/mips/pci/ops-tx4927.c
new file mode 100644
index 000000000..f7802f100
--- /dev/null
+++ b/arch/mips/pci/ops-tx4927.c
@@ -0,0 +1,524 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Define the pci_ops for the PCIC on Toshiba TX4927, TX4938, etc.
+ *
+ * Based on linux/arch/mips/pci/ops-tx4938.c,
+ *	    linux/arch/mips/pci/fixup-rbtx4938.c,
+ *	    linux/arch/mips/txx9/rbtx4938/setup.c,
+ *	    and RBTX49xx patch from CELF patch archive.
+ *
+ * 2003-2005 (c) MontaVista Software, Inc.
+ * Copyright (C) 2004 by Ralf Baechle (ralf@linux-mips.org)
+ * (C) Copyright TOSHIBA CORPORATION 2000-2001, 2004-2007
+ */
+#include <linux/kernel.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <asm/txx9/pci.h>
+#include <asm/txx9/tx4927pcic.h>
+
+static struct {
+	struct pci_controller *channel;
+	struct tx4927_pcic_reg __iomem *pcicptr;
+} pcicptrs[2];	/* TX4938 has 2 pcic */
+
+static void __init set_tx4927_pcicptr(struct pci_controller *channel,
+				      struct tx4927_pcic_reg __iomem *pcicptr)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(pcicptrs); i++) {
+		if (pcicptrs[i].channel == channel) {
+			pcicptrs[i].pcicptr = pcicptr;
+			return;
+		}
+	}
+	for (i = 0; i < ARRAY_SIZE(pcicptrs); i++) {
+		if (!pcicptrs[i].channel) {
+			pcicptrs[i].channel = channel;
+			pcicptrs[i].pcicptr = pcicptr;
+			return;
+		}
+	}
+	BUG();
+}
+
+struct tx4927_pcic_reg __iomem *get_tx4927_pcicptr(
+	struct pci_controller *channel)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(pcicptrs); i++) {
+		if (pcicptrs[i].channel == channel)
+			return pcicptrs[i].pcicptr;
+	}
+	return NULL;
+}
+
+static int mkaddr(struct pci_bus *bus, unsigned int devfn, int where,
+		  struct tx4927_pcic_reg __iomem *pcicptr)
+{
+	if (bus->parent == NULL &&
+	    devfn >= PCI_DEVFN(TX4927_PCIC_MAX_DEVNU, 0))
+		return -1;
+	__raw_writel(((bus->number & 0xff) << 0x10)
+		     | ((devfn & 0xff) << 0x08) | (where & 0xfc)
+		     | (bus->parent ? 1 : 0),
+		     &pcicptr->g2pcfgadrs);
+	/* clear M_ABORT and Disable M_ABORT Int. */
+	__raw_writel((__raw_readl(&pcicptr->pcistatus) & 0x0000ffff)
+		     | (PCI_STATUS_REC_MASTER_ABORT << 16),
+		     &pcicptr->pcistatus);
+	return 0;
+}
+
+static int check_abort(struct tx4927_pcic_reg __iomem *pcicptr)
+{
+	int code = PCIBIOS_SUCCESSFUL;
+
+	/* wait write cycle completion before checking error status */
+	while (__raw_readl(&pcicptr->pcicstatus) & TX4927_PCIC_PCICSTATUS_IWB)
+		;
+	if (__raw_readl(&pcicptr->pcistatus)
+	    & (PCI_STATUS_REC_MASTER_ABORT << 16)) {
+		__raw_writel((__raw_readl(&pcicptr->pcistatus) & 0x0000ffff)
+			     | (PCI_STATUS_REC_MASTER_ABORT << 16),
+			     &pcicptr->pcistatus);
+		/* flush write buffer */
+		iob();
+		code = PCIBIOS_DEVICE_NOT_FOUND;
+	}
+	return code;
+}
+
+static u8 icd_readb(int offset, struct tx4927_pcic_reg __iomem *pcicptr)
+{
+#ifdef __BIG_ENDIAN
+	offset ^= 3;
+#endif
+	return __raw_readb((void __iomem *)&pcicptr->g2pcfgdata + offset);
+}
+static u16 icd_readw(int offset, struct tx4927_pcic_reg __iomem *pcicptr)
+{
+#ifdef __BIG_ENDIAN
+	offset ^= 2;
+#endif
+	return __raw_readw((void __iomem *)&pcicptr->g2pcfgdata + offset);
+}
+static u32 icd_readl(struct tx4927_pcic_reg __iomem *pcicptr)
+{
+	return __raw_readl(&pcicptr->g2pcfgdata);
+}
+static void icd_writeb(u8 val, int offset,
+		       struct tx4927_pcic_reg __iomem *pcicptr)
+{
+#ifdef __BIG_ENDIAN
+	offset ^= 3;
+#endif
+	__raw_writeb(val, (void __iomem *)&pcicptr->g2pcfgdata + offset);
+}
+static void icd_writew(u16 val, int offset,
+		       struct tx4927_pcic_reg __iomem *pcicptr)
+{
+#ifdef __BIG_ENDIAN
+	offset ^= 2;
+#endif
+	__raw_writew(val, (void __iomem *)&pcicptr->g2pcfgdata + offset);
+}
+static void icd_writel(u32 val, struct tx4927_pcic_reg __iomem *pcicptr)
+{
+	__raw_writel(val, &pcicptr->g2pcfgdata);
+}
+
+static struct tx4927_pcic_reg __iomem *pci_bus_to_pcicptr(struct pci_bus *bus)
+{
+	struct pci_controller *channel = bus->sysdata;
+	return get_tx4927_pcicptr(channel);
+}
+
+static int tx4927_pci_config_read(struct pci_bus *bus, unsigned int devfn,
+				  int where, int size, u32 *val)
+{
+	struct tx4927_pcic_reg __iomem *pcicptr = pci_bus_to_pcicptr(bus);
+
+	if (mkaddr(bus, devfn, where, pcicptr)) {
+		*val = 0xffffffff;
+		return -1;
+	}
+	switch (size) {
+	case 1:
+		*val = icd_readb(where & 3, pcicptr);
+		break;
+	case 2:
+		*val = icd_readw(where & 3, pcicptr);
+		break;
+	default:
+		*val = icd_readl(pcicptr);
+	}
+	return check_abort(pcicptr);
+}
+
+static int tx4927_pci_config_write(struct pci_bus *bus, unsigned int devfn,
+				   int where, int size, u32 val)
+{
+	struct tx4927_pcic_reg __iomem *pcicptr = pci_bus_to_pcicptr(bus);
+
+	if (mkaddr(bus, devfn, where, pcicptr))
+		return -1;
+	switch (size) {
+	case 1:
+		icd_writeb(val, where & 3, pcicptr);
+		break;
+	case 2:
+		icd_writew(val, where & 3, pcicptr);
+		break;
+	default:
+		icd_writel(val, pcicptr);
+	}
+	return check_abort(pcicptr);
+}
+
+static struct pci_ops tx4927_pci_ops = {
+	.read = tx4927_pci_config_read,
+	.write = tx4927_pci_config_write,
+};
+
+static struct {
+	u8 trdyto;
+	u8 retryto;
+	u16 gbwc;
+} tx4927_pci_opts = {
+	.trdyto = 0,
+	.retryto = 0,
+	.gbwc = 0xfe0,	/* 4064 GBUSCLK for CCFG.GTOT=0b11 */
+};
+
+char *tx4927_pcibios_setup(char *str)
+{
+	if (!strncmp(str, "trdyto=", 7)) {
+		u8 val = 0;
+		if (kstrtou8(str + 7, 0, &val) == 0)
+			tx4927_pci_opts.trdyto = val;
+		return NULL;
+	}
+	if (!strncmp(str, "retryto=", 8)) {
+		u8 val = 0;
+		if (kstrtou8(str + 8, 0, &val) == 0)
+			tx4927_pci_opts.retryto = val;
+		return NULL;
+	}
+	if (!strncmp(str, "gbwc=", 5)) {
+		u16 val;
+		if (kstrtou16(str + 5, 0, &val) == 0)
+			tx4927_pci_opts.gbwc = val;
+		return NULL;
+	}
+	return str;
+}
+
+void __init tx4927_pcic_setup(struct tx4927_pcic_reg __iomem *pcicptr,
+			      struct pci_controller *channel, int extarb)
+{
+	int i;
+	unsigned long flags;
+
+	set_tx4927_pcicptr(channel, pcicptr);
+
+	if (!channel->pci_ops)
+		printk(KERN_INFO
+		       "PCIC -- DID:%04x VID:%04x RID:%02x Arbiter:%s\n",
+		       __raw_readl(&pcicptr->pciid) >> 16,
+		       __raw_readl(&pcicptr->pciid) & 0xffff,
+		       __raw_readl(&pcicptr->pciccrev) & 0xff,
+			extarb ? "External" : "Internal");
+	channel->pci_ops = &tx4927_pci_ops;
+
+	local_irq_save(flags);
+
+	/* Disable All Initiator Space */
+	__raw_writel(__raw_readl(&pcicptr->pciccfg)
+		     & ~(TX4927_PCIC_PCICCFG_G2PMEN(0)
+			 | TX4927_PCIC_PCICCFG_G2PMEN(1)
+			 | TX4927_PCIC_PCICCFG_G2PMEN(2)
+			 | TX4927_PCIC_PCICCFG_G2PIOEN),
+		     &pcicptr->pciccfg);
+
+	/* GB->PCI mappings */
+	__raw_writel((channel->io_resource->end - channel->io_resource->start)
+		     >> 4,
+		     &pcicptr->g2piomask);
+	____raw_writeq((channel->io_resource->start +
+			channel->io_map_base - IO_BASE) |
+#ifdef __BIG_ENDIAN
+		       TX4927_PCIC_G2PIOGBASE_ECHG
+#else
+		       TX4927_PCIC_G2PIOGBASE_BSDIS
+#endif
+		       , &pcicptr->g2piogbase);
+	____raw_writeq(channel->io_resource->start - channel->io_offset,
+		       &pcicptr->g2piopbase);
+	for (i = 0; i < 3; i++) {
+		__raw_writel(0, &pcicptr->g2pmmask[i]);
+		____raw_writeq(0, &pcicptr->g2pmgbase[i]);
+		____raw_writeq(0, &pcicptr->g2pmpbase[i]);
+	}
+	if (channel->mem_resource->end) {
+		__raw_writel((channel->mem_resource->end
+			      - channel->mem_resource->start) >> 4,
+			     &pcicptr->g2pmmask[0]);
+		____raw_writeq(channel->mem_resource->start |
+#ifdef __BIG_ENDIAN
+			       TX4927_PCIC_G2PMnGBASE_ECHG
+#else
+			       TX4927_PCIC_G2PMnGBASE_BSDIS
+#endif
+			       , &pcicptr->g2pmgbase[0]);
+		____raw_writeq(channel->mem_resource->start -
+			       channel->mem_offset,
+			       &pcicptr->g2pmpbase[0]);
+	}
+	/* PCI->GB mappings (I/O 256B) */
+	__raw_writel(0, &pcicptr->p2giopbase); /* 256B */
+	____raw_writeq(0, &pcicptr->p2giogbase);
+	/* PCI->GB mappings (MEM 512MB (64MB on R1.x)) */
+	__raw_writel(0, &pcicptr->p2gm0plbase);
+	__raw_writel(0, &pcicptr->p2gm0pubase);
+	____raw_writeq(TX4927_PCIC_P2GMnGBASE_TMEMEN |
+#ifdef __BIG_ENDIAN
+		       TX4927_PCIC_P2GMnGBASE_TECHG
+#else
+		       TX4927_PCIC_P2GMnGBASE_TBSDIS
+#endif
+		       , &pcicptr->p2gmgbase[0]);
+	/* PCI->GB mappings (MEM 16MB) */
+	__raw_writel(0xffffffff, &pcicptr->p2gm1plbase);
+	__raw_writel(0xffffffff, &pcicptr->p2gm1pubase);
+	____raw_writeq(0, &pcicptr->p2gmgbase[1]);
+	/* PCI->GB mappings (MEM 1MB) */
+	__raw_writel(0xffffffff, &pcicptr->p2gm2pbase); /* 1MB */
+	____raw_writeq(0, &pcicptr->p2gmgbase[2]);
+
+	/* Clear all (including IRBER) except for GBWC */
+	__raw_writel((tx4927_pci_opts.gbwc << 16)
+		     & TX4927_PCIC_PCICCFG_GBWC_MASK,
+		     &pcicptr->pciccfg);
+	/* Enable Initiator Memory Space */
+	if (channel->mem_resource->end)
+		__raw_writel(__raw_readl(&pcicptr->pciccfg)
+			     | TX4927_PCIC_PCICCFG_G2PMEN(0),
+			     &pcicptr->pciccfg);
+	/* Enable Initiator I/O Space */
+	if (channel->io_resource->end)
+		__raw_writel(__raw_readl(&pcicptr->pciccfg)
+			     | TX4927_PCIC_PCICCFG_G2PIOEN,
+			     &pcicptr->pciccfg);
+	/* Enable Initiator Config */
+	__raw_writel(__raw_readl(&pcicptr->pciccfg)
+		     | TX4927_PCIC_PCICCFG_ICAEN | TX4927_PCIC_PCICCFG_TCAR,
+		     &pcicptr->pciccfg);
+
+	/* Do not use MEMMUL, MEMINF: YMFPCI card causes M_ABORT. */
+	__raw_writel(0, &pcicptr->pcicfg1);
+
+	__raw_writel((__raw_readl(&pcicptr->g2ptocnt) & ~0xffff)
+		     | (tx4927_pci_opts.trdyto & 0xff)
+		     | ((tx4927_pci_opts.retryto & 0xff) << 8),
+		     &pcicptr->g2ptocnt);
+
+	/* Clear All Local Bus Status */
+	__raw_writel(TX4927_PCIC_PCICSTATUS_ALL, &pcicptr->pcicstatus);
+	/* Enable All Local Bus Interrupts */
+	__raw_writel(TX4927_PCIC_PCICSTATUS_ALL, &pcicptr->pcicmask);
+	/* Clear All Initiator Status */
+	__raw_writel(TX4927_PCIC_G2PSTATUS_ALL, &pcicptr->g2pstatus);
+	/* Enable All Initiator Interrupts */
+	__raw_writel(TX4927_PCIC_G2PSTATUS_ALL, &pcicptr->g2pmask);
+	/* Clear All PCI Status Error */
+	__raw_writel((__raw_readl(&pcicptr->pcistatus) & 0x0000ffff)
+		     | (TX4927_PCIC_PCISTATUS_ALL << 16),
+		     &pcicptr->pcistatus);
+	/* Enable All PCI Status Error Interrupts */
+	__raw_writel(TX4927_PCIC_PCISTATUS_ALL, &pcicptr->pcimask);
+
+	if (!extarb) {
+		/* Reset Bus Arbiter */
+		__raw_writel(TX4927_PCIC_PBACFG_RPBA, &pcicptr->pbacfg);
+		__raw_writel(0, &pcicptr->pbabm);
+		/* Enable Bus Arbiter */
+		__raw_writel(TX4927_PCIC_PBACFG_PBAEN, &pcicptr->pbacfg);
+	}
+
+	__raw_writel(PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY
+		     | PCI_COMMAND_PARITY | PCI_COMMAND_SERR,
+		     &pcicptr->pcistatus);
+	local_irq_restore(flags);
+
+	printk(KERN_DEBUG
+	       "PCI: COMMAND=%04x,PCIMASK=%04x,"
+	       "TRDYTO=%02x,RETRYTO=%02x,GBWC=%03x\n",
+	       __raw_readl(&pcicptr->pcistatus) & 0xffff,
+	       __raw_readl(&pcicptr->pcimask) & 0xffff,
+	       __raw_readl(&pcicptr->g2ptocnt) & 0xff,
+	       (__raw_readl(&pcicptr->g2ptocnt) & 0xff00) >> 8,
+	       (__raw_readl(&pcicptr->pciccfg) >> 16) & 0xfff);
+}
+
+static void tx4927_report_pcic_status1(struct tx4927_pcic_reg __iomem *pcicptr)
+{
+	__u16 pcistatus = (__u16)(__raw_readl(&pcicptr->pcistatus) >> 16);
+	__u32 g2pstatus = __raw_readl(&pcicptr->g2pstatus);
+	__u32 pcicstatus = __raw_readl(&pcicptr->pcicstatus);
+	static struct {
+		__u32 flag;
+		const char *str;
+	} pcistat_tbl[] = {
+		{ PCI_STATUS_DETECTED_PARITY,	"DetectedParityError" },
+		{ PCI_STATUS_SIG_SYSTEM_ERROR,	"SignaledSystemError" },
+		{ PCI_STATUS_REC_MASTER_ABORT,	"ReceivedMasterAbort" },
+		{ PCI_STATUS_REC_TARGET_ABORT,	"ReceivedTargetAbort" },
+		{ PCI_STATUS_SIG_TARGET_ABORT,	"SignaledTargetAbort" },
+		{ PCI_STATUS_PARITY,	"MasterParityError" },
+	}, g2pstat_tbl[] = {
+		{ TX4927_PCIC_G2PSTATUS_TTOE,	"TIOE" },
+		{ TX4927_PCIC_G2PSTATUS_RTOE,	"RTOE" },
+	}, pcicstat_tbl[] = {
+		{ TX4927_PCIC_PCICSTATUS_PME,	"PME" },
+		{ TX4927_PCIC_PCICSTATUS_TLB,	"TLB" },
+		{ TX4927_PCIC_PCICSTATUS_NIB,	"NIB" },
+		{ TX4927_PCIC_PCICSTATUS_ZIB,	"ZIB" },
+		{ TX4927_PCIC_PCICSTATUS_PERR,	"PERR" },
+		{ TX4927_PCIC_PCICSTATUS_SERR,	"SERR" },
+		{ TX4927_PCIC_PCICSTATUS_GBE,	"GBE" },
+		{ TX4927_PCIC_PCICSTATUS_IWB,	"IWB" },
+	};
+	int i, cont;
+
+	printk(KERN_ERR "");
+	if (pcistatus & TX4927_PCIC_PCISTATUS_ALL) {
+		printk(KERN_CONT "pcistat:%04x(", pcistatus);
+		for (i = 0, cont = 0; i < ARRAY_SIZE(pcistat_tbl); i++)
+			if (pcistatus & pcistat_tbl[i].flag)
+				printk(KERN_CONT "%s%s",
+				       cont++ ? " " : "", pcistat_tbl[i].str);
+		printk(KERN_CONT ") ");
+	}
+	if (g2pstatus & TX4927_PCIC_G2PSTATUS_ALL) {
+		printk(KERN_CONT "g2pstatus:%08x(", g2pstatus);
+		for (i = 0, cont = 0; i < ARRAY_SIZE(g2pstat_tbl); i++)
+			if (g2pstatus & g2pstat_tbl[i].flag)
+				printk(KERN_CONT "%s%s",
+				       cont++ ? " " : "", g2pstat_tbl[i].str);
+		printk(KERN_CONT ") ");
+	}
+	if (pcicstatus & TX4927_PCIC_PCICSTATUS_ALL) {
+		printk(KERN_CONT "pcicstatus:%08x(", pcicstatus);
+		for (i = 0, cont = 0; i < ARRAY_SIZE(pcicstat_tbl); i++)
+			if (pcicstatus & pcicstat_tbl[i].flag)
+				printk(KERN_CONT "%s%s",
+				       cont++ ? " " : "", pcicstat_tbl[i].str);
+		printk(KERN_CONT ")");
+	}
+	printk(KERN_CONT "\n");
+}
+
+void tx4927_report_pcic_status(void)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(pcicptrs); i++) {
+		if (pcicptrs[i].pcicptr)
+			tx4927_report_pcic_status1(pcicptrs[i].pcicptr);
+	}
+}
+
+static void tx4927_dump_pcic_settings1(struct tx4927_pcic_reg __iomem *pcicptr)
+{
+	int i;
+	__u32 __iomem *preg = (__u32 __iomem *)pcicptr;
+
+	printk(KERN_INFO "tx4927 pcic (0x%p) settings:", pcicptr);
+	for (i = 0; i < sizeof(struct tx4927_pcic_reg); i += 4, preg++) {
+		if (i % 32 == 0) {
+			printk(KERN_CONT "\n");
+			printk(KERN_INFO "%04x:", i);
+		}
+		/* skip registers with side-effects */
+		if (i == offsetof(struct tx4927_pcic_reg, g2pintack)
+		    || i == offsetof(struct tx4927_pcic_reg, g2pspc)
+		    || i == offsetof(struct tx4927_pcic_reg, g2pcfgadrs)
+		    || i == offsetof(struct tx4927_pcic_reg, g2pcfgdata)) {
+			printk(KERN_CONT " XXXXXXXX");
+			continue;
+		}
+		printk(KERN_CONT " %08x", __raw_readl(preg));
+	}
+	printk(KERN_CONT "\n");
+}
+
+void tx4927_dump_pcic_settings(void)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(pcicptrs); i++) {
+		if (pcicptrs[i].pcicptr)
+			tx4927_dump_pcic_settings1(pcicptrs[i].pcicptr);
+	}
+}
+
+irqreturn_t tx4927_pcierr_interrupt(int irq, void *dev_id)
+{
+	struct pt_regs *regs = get_irq_regs();
+	struct tx4927_pcic_reg __iomem *pcicptr =
+		(struct tx4927_pcic_reg __iomem *)(unsigned long)dev_id;
+
+	if (txx9_pci_err_action != TXX9_PCI_ERR_IGNORE) {
+		printk(KERN_WARNING "PCIERR interrupt at 0x%0*lx\n",
+		       (int)(2 * sizeof(unsigned long)), regs->cp0_epc);
+		tx4927_report_pcic_status1(pcicptr);
+	}
+	if (txx9_pci_err_action != TXX9_PCI_ERR_PANIC) {
+		/* clear all pci errors */
+		__raw_writel((__raw_readl(&pcicptr->pcistatus) & 0x0000ffff)
+			     | (TX4927_PCIC_PCISTATUS_ALL << 16),
+			     &pcicptr->pcistatus);
+		__raw_writel(TX4927_PCIC_G2PSTATUS_ALL, &pcicptr->g2pstatus);
+		__raw_writel(TX4927_PCIC_PBASTATUS_ALL, &pcicptr->pbastatus);
+		__raw_writel(TX4927_PCIC_PCICSTATUS_ALL, &pcicptr->pcicstatus);
+		return IRQ_HANDLED;
+	}
+	console_verbose();
+	tx4927_dump_pcic_settings1(pcicptr);
+	panic("PCI error.");
+}
+
+#ifdef CONFIG_TOSHIBA_FPCIB0
+static void tx4927_quirk_slc90e66_bridge(struct pci_dev *dev)
+{
+	struct tx4927_pcic_reg __iomem *pcicptr = pci_bus_to_pcicptr(dev->bus);
+
+	if (!pcicptr)
+		return;
+	if (__raw_readl(&pcicptr->pbacfg) & TX4927_PCIC_PBACFG_PBAEN) {
+		/* Reset Bus Arbiter */
+		__raw_writel(TX4927_PCIC_PBACFG_RPBA, &pcicptr->pbacfg);
+		/*
+		 * swap reqBP and reqXP (raise priority of SLC90E66).
+		 * SLC90E66(PCI-ISA bridge) is connected to REQ2 on
+		 * PCI Backplane board.
+		 */
+		__raw_writel(0x72543610, &pcicptr->pbareqport);
+		__raw_writel(0, &pcicptr->pbabm);
+		/* Use Fixed ParkMaster (required by SLC90E66) */
+		__raw_writel(TX4927_PCIC_PBACFG_FIXPA, &pcicptr->pbacfg);
+		/* Enable Bus Arbiter */
+		__raw_writel(TX4927_PCIC_PBACFG_FIXPA |
+			     TX4927_PCIC_PBACFG_PBAEN,
+			     &pcicptr->pbacfg);
+		printk(KERN_INFO "PCI: Use Fixed Park Master (REQPORT %08x)\n",
+		       __raw_readl(&pcicptr->pbareqport));
+	}
+}
+#define PCI_DEVICE_ID_EFAR_SLC90E66_0 0x9460
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_EFAR, PCI_DEVICE_ID_EFAR_SLC90E66_0,
+	tx4927_quirk_slc90e66_bridge);
+#endif
diff --git a/arch/mips/pci/pci-alchemy.c b/arch/mips/pci/pci-alchemy.c
new file mode 100644
index 000000000..1c722dd0c
--- /dev/null
+++ b/arch/mips/pci/pci-alchemy.c
@@ -0,0 +1,536 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Alchemy PCI host mode support.
+ *
+ * Copyright 2001-2003, 2007-2008 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc. <source@mvista.com>
+ *
+ * Support for all devices (greater than 16) added by David Gathright.
+ */
+
+#include <linux/clk.h>
+#include <linux/export.h>
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/syscore_ops.h>
+#include <linux/vmalloc.h>
+#include <linux/dma-map-ops.h> /* for dma_default_coherent */
+
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/tlbmisc.h>
+
+#ifdef CONFIG_PCI_DEBUG
+#define DBG(x...) printk(KERN_DEBUG x)
+#else
+#define DBG(x...) do {} while (0)
+#endif
+
+#define PCI_ACCESS_READ		0
+#define PCI_ACCESS_WRITE	1
+
+struct alchemy_pci_context {
+	struct pci_controller alchemy_pci_ctrl; /* leave as first member! */
+	void __iomem *regs;			/* ctrl base */
+	/* tools for wired entry for config space access */
+	unsigned long last_elo0;
+	unsigned long last_elo1;
+	int wired_entry;
+	struct vm_struct *pci_cfg_vm;
+
+	unsigned long pm[12];
+
+	int (*board_map_irq)(const struct pci_dev *d, u8 slot, u8 pin);
+	int (*board_pci_idsel)(unsigned int devsel, int assert);
+};
+
+/* for syscore_ops. There's only one PCI controller on Alchemy chips, so this
+ * should suffice for now.
+ */
+static struct alchemy_pci_context *__alchemy_pci_ctx;
+
+
+/* IO/MEM resources for PCI. Keep the memres in sync with fixup_bigphys_addr
+ * in arch/mips/alchemy/common/setup.c
+ */
+static struct resource alchemy_pci_def_memres = {
+	.start	= ALCHEMY_PCI_MEMWIN_START,
+	.end	= ALCHEMY_PCI_MEMWIN_END,
+	.name	= "PCI memory space",
+	.flags	= IORESOURCE_MEM
+};
+
+static struct resource alchemy_pci_def_iores = {
+	.start	= ALCHEMY_PCI_IOWIN_START,
+	.end	= ALCHEMY_PCI_IOWIN_END,
+	.name	= "PCI IO space",
+	.flags	= IORESOURCE_IO
+};
+
+static void mod_wired_entry(int entry, unsigned long entrylo0,
+		unsigned long entrylo1, unsigned long entryhi,
+		unsigned long pagemask)
+{
+	unsigned long old_pagemask;
+	unsigned long old_ctx;
+
+	/* Save old context and create impossible VPN2 value */
+	old_ctx = read_c0_entryhi() & MIPS_ENTRYHI_ASID;
+	old_pagemask = read_c0_pagemask();
+	write_c0_index(entry);
+	write_c0_pagemask(pagemask);
+	write_c0_entryhi(entryhi);
+	write_c0_entrylo0(entrylo0);
+	write_c0_entrylo1(entrylo1);
+	tlb_write_indexed();
+	write_c0_entryhi(old_ctx);
+	write_c0_pagemask(old_pagemask);
+}
+
+static void alchemy_pci_wired_entry(struct alchemy_pci_context *ctx)
+{
+	ctx->wired_entry = read_c0_wired();
+	add_wired_entry(0, 0, (unsigned long)ctx->pci_cfg_vm->addr, PM_4K);
+	ctx->last_elo0 = ctx->last_elo1 = ~0;
+}
+
+static int config_access(unsigned char access_type, struct pci_bus *bus,
+			 unsigned int dev_fn, unsigned char where, u32 *data)
+{
+	struct alchemy_pci_context *ctx = bus->sysdata;
+	unsigned int device = PCI_SLOT(dev_fn);
+	unsigned int function = PCI_FUNC(dev_fn);
+	unsigned long offset, status, cfg_base, flags, entryLo0, entryLo1, r;
+	int error = PCIBIOS_SUCCESSFUL;
+
+	if (device > 19) {
+		*data = 0xffffffff;
+		return -1;
+	}
+
+	local_irq_save(flags);
+	r = __raw_readl(ctx->regs + PCI_REG_STATCMD) & 0x0000ffff;
+	r |= PCI_STATCMD_STATUS(0x2000);
+	__raw_writel(r, ctx->regs + PCI_REG_STATCMD);
+	wmb();
+
+	/* Allow board vendors to implement their own off-chip IDSEL.
+	 * If it doesn't succeed, may as well bail out at this point.
+	 */
+	if (ctx->board_pci_idsel(device, 1) == 0) {
+		*data = 0xffffffff;
+		local_irq_restore(flags);
+		return -1;
+	}
+
+	/* Setup the config window */
+	if (bus->number == 0)
+		cfg_base = (1 << device) << 11;
+	else
+		cfg_base = 0x80000000 | (bus->number << 16) | (device << 11);
+
+	/* Setup the lower bits of the 36-bit address */
+	offset = (function << 8) | (where & ~0x3);
+	/* Pick up any address that falls below the page mask */
+	offset |= cfg_base & ~PAGE_MASK;
+
+	/* Page boundary */
+	cfg_base = cfg_base & PAGE_MASK;
+
+	/* To improve performance, if the current device is the same as
+	 * the last device accessed, we don't touch the TLB.
+	 */
+	entryLo0 = (6 << 26) | (cfg_base >> 6) | (2 << 3) | 7;
+	entryLo1 = (6 << 26) | (cfg_base >> 6) | (0x1000 >> 6) | (2 << 3) | 7;
+	if ((entryLo0 != ctx->last_elo0) || (entryLo1 != ctx->last_elo1)) {
+		mod_wired_entry(ctx->wired_entry, entryLo0, entryLo1,
+				(unsigned long)ctx->pci_cfg_vm->addr, PM_4K);
+		ctx->last_elo0 = entryLo0;
+		ctx->last_elo1 = entryLo1;
+	}
+
+	if (access_type == PCI_ACCESS_WRITE)
+		__raw_writel(*data, ctx->pci_cfg_vm->addr + offset);
+	else
+		*data = __raw_readl(ctx->pci_cfg_vm->addr + offset);
+	wmb();
+
+	DBG("alchemy-pci: cfg access %d bus %u dev %u at %x dat %x conf %lx\n",
+	    access_type, bus->number, device, where, *data, offset);
+
+	/* check for errors, master abort */
+	status = __raw_readl(ctx->regs + PCI_REG_STATCMD);
+	if (status & (1 << 29)) {
+		*data = 0xffffffff;
+		error = -1;
+		DBG("alchemy-pci: master abort on cfg access %d bus %d dev %d\n",
+		    access_type, bus->number, device);
+	} else if ((status >> 28) & 0xf) {
+		DBG("alchemy-pci: PCI ERR detected: dev %d, status %lx\n",
+		    device, (status >> 28) & 0xf);
+
+		/* clear errors */
+		__raw_writel(status & 0xf000ffff, ctx->regs + PCI_REG_STATCMD);
+
+		*data = 0xffffffff;
+		error = -1;
+	}
+
+	/* Take away the IDSEL. */
+	(void)ctx->board_pci_idsel(device, 0);
+
+	local_irq_restore(flags);
+	return error;
+}
+
+static int read_config_byte(struct pci_bus *bus, unsigned int devfn,
+			    int where,	u8 *val)
+{
+	u32 data;
+	int ret = config_access(PCI_ACCESS_READ, bus, devfn, where, &data);
+
+	if (where & 1)
+		data >>= 8;
+	if (where & 2)
+		data >>= 16;
+	*val = data & 0xff;
+	return ret;
+}
+
+static int read_config_word(struct pci_bus *bus, unsigned int devfn,
+			    int where, u16 *val)
+{
+	u32 data;
+	int ret = config_access(PCI_ACCESS_READ, bus, devfn, where, &data);
+
+	if (where & 2)
+		data >>= 16;
+	*val = data & 0xffff;
+	return ret;
+}
+
+static int read_config_dword(struct pci_bus *bus, unsigned int devfn,
+			     int where, u32 *val)
+{
+	return config_access(PCI_ACCESS_READ, bus, devfn, where, val);
+}
+
+static int write_config_byte(struct pci_bus *bus, unsigned int devfn,
+			     int where, u8 val)
+{
+	u32 data = 0;
+
+	if (config_access(PCI_ACCESS_READ, bus, devfn, where, &data))
+		return -1;
+
+	data = (data & ~(0xff << ((where & 3) << 3))) |
+	       (val << ((where & 3) << 3));
+
+	if (config_access(PCI_ACCESS_WRITE, bus, devfn, where, &data))
+		return -1;
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int write_config_word(struct pci_bus *bus, unsigned int devfn,
+			     int where, u16 val)
+{
+	u32 data = 0;
+
+	if (config_access(PCI_ACCESS_READ, bus, devfn, where, &data))
+		return -1;
+
+	data = (data & ~(0xffff << ((where & 3) << 3))) |
+	       (val << ((where & 3) << 3));
+
+	if (config_access(PCI_ACCESS_WRITE, bus, devfn, where, &data))
+		return -1;
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int write_config_dword(struct pci_bus *bus, unsigned int devfn,
+			      int where, u32 val)
+{
+	return config_access(PCI_ACCESS_WRITE, bus, devfn, where, &val);
+}
+
+static int alchemy_pci_read(struct pci_bus *bus, unsigned int devfn,
+		       int where, int size, u32 *val)
+{
+	switch (size) {
+	case 1: {
+			u8 _val;
+			int rc = read_config_byte(bus, devfn, where, &_val);
+
+			*val = _val;
+			return rc;
+		}
+	case 2: {
+			u16 _val;
+			int rc = read_config_word(bus, devfn, where, &_val);
+
+			*val = _val;
+			return rc;
+		}
+	default:
+		return read_config_dword(bus, devfn, where, val);
+	}
+}
+
+static int alchemy_pci_write(struct pci_bus *bus, unsigned int devfn,
+			     int where, int size, u32 val)
+{
+	switch (size) {
+	case 1:
+		return write_config_byte(bus, devfn, where, (u8) val);
+	case 2:
+		return write_config_word(bus, devfn, where, (u16) val);
+	default:
+		return write_config_dword(bus, devfn, where, val);
+	}
+}
+
+static struct pci_ops alchemy_pci_ops = {
+	.read	= alchemy_pci_read,
+	.write	= alchemy_pci_write,
+};
+
+static int alchemy_pci_def_idsel(unsigned int devsel, int assert)
+{
+	return 1;	/* success */
+}
+
+/* save PCI controller register contents. */
+static int alchemy_pci_suspend(void)
+{
+	struct alchemy_pci_context *ctx = __alchemy_pci_ctx;
+	if (!ctx)
+		return 0;
+
+	ctx->pm[0]  = __raw_readl(ctx->regs + PCI_REG_CMEM);
+	ctx->pm[1]  = __raw_readl(ctx->regs + PCI_REG_CONFIG) & 0x0009ffff;
+	ctx->pm[2]  = __raw_readl(ctx->regs + PCI_REG_B2BMASK_CCH);
+	ctx->pm[3]  = __raw_readl(ctx->regs + PCI_REG_B2BBASE0_VID);
+	ctx->pm[4]  = __raw_readl(ctx->regs + PCI_REG_B2BBASE1_SID);
+	ctx->pm[5]  = __raw_readl(ctx->regs + PCI_REG_MWMASK_DEV);
+	ctx->pm[6]  = __raw_readl(ctx->regs + PCI_REG_MWBASE_REV_CCL);
+	ctx->pm[7]  = __raw_readl(ctx->regs + PCI_REG_ID);
+	ctx->pm[8]  = __raw_readl(ctx->regs + PCI_REG_CLASSREV);
+	ctx->pm[9]  = __raw_readl(ctx->regs + PCI_REG_PARAM);
+	ctx->pm[10] = __raw_readl(ctx->regs + PCI_REG_MBAR);
+	ctx->pm[11] = __raw_readl(ctx->regs + PCI_REG_TIMEOUT);
+
+	return 0;
+}
+
+static void alchemy_pci_resume(void)
+{
+	struct alchemy_pci_context *ctx = __alchemy_pci_ctx;
+	if (!ctx)
+		return;
+
+	__raw_writel(ctx->pm[0],  ctx->regs + PCI_REG_CMEM);
+	__raw_writel(ctx->pm[2],  ctx->regs + PCI_REG_B2BMASK_CCH);
+	__raw_writel(ctx->pm[3],  ctx->regs + PCI_REG_B2BBASE0_VID);
+	__raw_writel(ctx->pm[4],  ctx->regs + PCI_REG_B2BBASE1_SID);
+	__raw_writel(ctx->pm[5],  ctx->regs + PCI_REG_MWMASK_DEV);
+	__raw_writel(ctx->pm[6],  ctx->regs + PCI_REG_MWBASE_REV_CCL);
+	__raw_writel(ctx->pm[7],  ctx->regs + PCI_REG_ID);
+	__raw_writel(ctx->pm[8],  ctx->regs + PCI_REG_CLASSREV);
+	__raw_writel(ctx->pm[9],  ctx->regs + PCI_REG_PARAM);
+	__raw_writel(ctx->pm[10], ctx->regs + PCI_REG_MBAR);
+	__raw_writel(ctx->pm[11], ctx->regs + PCI_REG_TIMEOUT);
+	wmb();
+	__raw_writel(ctx->pm[1],  ctx->regs + PCI_REG_CONFIG);
+	wmb();
+
+	/* YAMON on all db1xxx boards wipes the TLB and writes zero to C0_wired
+	 * on resume, making it necessary to recreate it as soon as possible.
+	 */
+	ctx->wired_entry = 8191;	/* impossibly high value */
+	alchemy_pci_wired_entry(ctx);	/* install it */
+}
+
+static struct syscore_ops alchemy_pci_pmops = {
+	.suspend	= alchemy_pci_suspend,
+	.resume		= alchemy_pci_resume,
+};
+
+static int alchemy_pci_probe(struct platform_device *pdev)
+{
+	struct alchemy_pci_platdata *pd = pdev->dev.platform_data;
+	struct alchemy_pci_context *ctx;
+	void __iomem *virt_io;
+	unsigned long val;
+	struct resource *r;
+	struct clk *c;
+	int ret;
+
+	/* need at least PCI IRQ mapping table */
+	if (!pd) {
+		dev_err(&pdev->dev, "need platform data for PCI setup\n");
+		ret = -ENODEV;
+		goto out;
+	}
+
+	ctx = kzalloc(sizeof(*ctx), GFP_KERNEL);
+	if (!ctx) {
+		dev_err(&pdev->dev, "no memory for pcictl context\n");
+		ret = -ENOMEM;
+		goto out;
+	}
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!r) {
+		dev_err(&pdev->dev, "no	 pcictl ctrl regs resource\n");
+		ret = -ENODEV;
+		goto out1;
+	}
+
+	if (!request_mem_region(r->start, resource_size(r), pdev->name)) {
+		dev_err(&pdev->dev, "cannot claim pci regs\n");
+		ret = -ENODEV;
+		goto out1;
+	}
+
+	c = clk_get(&pdev->dev, "pci_clko");
+	if (IS_ERR(c)) {
+		dev_err(&pdev->dev, "unable to find PCI clock\n");
+		ret = PTR_ERR(c);
+		goto out2;
+	}
+
+	ret = clk_prepare_enable(c);
+	if (ret) {
+		dev_err(&pdev->dev, "cannot enable PCI clock\n");
+		goto out6;
+	}
+
+	ctx->regs = ioremap(r->start, resource_size(r));
+	if (!ctx->regs) {
+		dev_err(&pdev->dev, "cannot map pci regs\n");
+		ret = -ENODEV;
+		goto out5;
+	}
+
+	/* map parts of the PCI IO area */
+	/* REVISIT: if this changes with a newer variant (doubt it) make this
+	 * a platform resource.
+	 */
+	virt_io = ioremap(AU1500_PCI_IO_PHYS_ADDR, 0x00100000);
+	if (!virt_io) {
+		dev_err(&pdev->dev, "cannot remap pci io space\n");
+		ret = -ENODEV;
+		goto out3;
+	}
+	ctx->alchemy_pci_ctrl.io_map_base = (unsigned long)virt_io;
+
+	/* Au1500 revisions older than AD have borked coherent PCI */
+	if (alchemy_get_cputype() == ALCHEMY_CPU_AU1500 &&
+	    read_c0_prid() < 0x01030202 && !dma_default_coherent) {
+		val = __raw_readl(ctx->regs + PCI_REG_CONFIG);
+		val |= PCI_CONFIG_NC;
+		__raw_writel(val, ctx->regs + PCI_REG_CONFIG);
+		wmb();
+		dev_info(&pdev->dev, "non-coherent PCI on Au1500 AA/AB/AC\n");
+	}
+
+	if (pd->board_map_irq)
+		ctx->board_map_irq = pd->board_map_irq;
+
+	if (pd->board_pci_idsel)
+		ctx->board_pci_idsel = pd->board_pci_idsel;
+	else
+		ctx->board_pci_idsel = alchemy_pci_def_idsel;
+
+	/* fill in relevant pci_controller members */
+	ctx->alchemy_pci_ctrl.pci_ops = &alchemy_pci_ops;
+	ctx->alchemy_pci_ctrl.mem_resource = &alchemy_pci_def_memres;
+	ctx->alchemy_pci_ctrl.io_resource = &alchemy_pci_def_iores;
+
+	/* we can't ioremap the entire pci config space because it's too large,
+	 * nor can we dynamically ioremap it because some drivers use the
+	 * PCI config routines from within atomic contex and that becomes a
+	 * problem in get_vm_area().  Instead we use one wired TLB entry to
+	 * handle all config accesses for all busses.
+	 */
+	ctx->pci_cfg_vm = get_vm_area(0x2000, VM_IOREMAP);
+	if (!ctx->pci_cfg_vm) {
+		dev_err(&pdev->dev, "unable to get vm area\n");
+		ret = -ENOMEM;
+		goto out4;
+	}
+	ctx->wired_entry = 8191;	/* impossibly high value */
+	alchemy_pci_wired_entry(ctx);	/* install it */
+
+	set_io_port_base((unsigned long)ctx->alchemy_pci_ctrl.io_map_base);
+
+	/* board may want to modify bits in the config register, do it now */
+	val = __raw_readl(ctx->regs + PCI_REG_CONFIG);
+	val &= ~pd->pci_cfg_clr;
+	val |= pd->pci_cfg_set;
+	val &= ~PCI_CONFIG_PD;		/* clear disable bit */
+	__raw_writel(val, ctx->regs + PCI_REG_CONFIG);
+	wmb();
+
+	__alchemy_pci_ctx = ctx;
+	platform_set_drvdata(pdev, ctx);
+	register_syscore_ops(&alchemy_pci_pmops);
+	register_pci_controller(&ctx->alchemy_pci_ctrl);
+
+	dev_info(&pdev->dev, "PCI controller at %ld MHz\n",
+		 clk_get_rate(c) / 1000000);
+
+	return 0;
+
+out4:
+	iounmap(virt_io);
+out3:
+	iounmap(ctx->regs);
+out5:
+	clk_disable_unprepare(c);
+out6:
+	clk_put(c);
+out2:
+	release_mem_region(r->start, resource_size(r));
+out1:
+	kfree(ctx);
+out:
+	return ret;
+}
+
+static struct platform_driver alchemy_pcictl_driver = {
+	.probe		= alchemy_pci_probe,
+	.driver = {
+		.name	= "alchemy-pci",
+	},
+};
+
+static int __init alchemy_pci_init(void)
+{
+	/* Au1500/Au1550 have PCI */
+	switch (alchemy_get_cputype()) {
+	case ALCHEMY_CPU_AU1500:
+	case ALCHEMY_CPU_AU1550:
+		return platform_driver_register(&alchemy_pcictl_driver);
+	}
+	return 0;
+}
+arch_initcall(alchemy_pci_init);
+
+
+int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	struct alchemy_pci_context *ctx = dev->sysdata;
+	if (ctx && ctx->board_map_irq)
+		return ctx->board_map_irq(dev, slot, pin);
+	return -1;
+}
+
+int pcibios_plat_dev_init(struct pci_dev *dev)
+{
+	return 0;
+}
diff --git a/arch/mips/pci/pci-ar2315.c b/arch/mips/pci/pci-ar2315.c
new file mode 100644
index 000000000..e17d862cf
--- /dev/null
+++ b/arch/mips/pci/pci-ar2315.c
@@ -0,0 +1,521 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ */
+
+/*
+ * Both AR2315 and AR2316 chips have PCI interface unit, which supports DMA
+ * and interrupt. PCI interface supports MMIO access method, but does not
+ * seem to support I/O ports.
+ *
+ * Read/write operation in the region 0x80000000-0xBFFFFFFF causes
+ * a memory read/write command on the PCI bus. 30 LSBs of address on
+ * the bus are taken from memory read/write request and 2 MSBs are
+ * determined by PCI unit configuration.
+ *
+ * To work with the configuration space instead of memory is necessary set
+ * the CFG_SEL bit in the PCI_MISC_CONFIG register.
+ *
+ * Devices on the bus can perform DMA requests via chip BAR1. PCI host
+ * controller BARs are programmend as if an external device is programmed.
+ * Which means that during configuration, IDSEL pin of the chip should be
+ * asserted.
+ *
+ * We know (and support) only one board that uses the PCI interface -
+ * Fonera 2.0g (FON2202). It has a USB EHCI controller connected to the
+ * AR2315 PCI bus. IDSEL pin of USB controller is connected to AD[13] line
+ * and IDSEL pin of AR2315 is connected to AD[16] line.
+ */
+
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/dma-direct.h>
+#include <linux/mm.h>
+#include <linux/delay.h>
+#include <linux/bitops.h>
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/io.h>
+#include <asm/paccess.h>
+
+/*
+ * PCI Bus Interface Registers
+ */
+#define AR2315_PCI_1MS_REG		0x0008
+
+#define AR2315_PCI_1MS_MASK		0x3FFFF	/* # of AHB clk cycles in 1ms */
+
+#define AR2315_PCI_MISC_CONFIG		0x000c
+
+#define AR2315_PCIMISC_TXD_EN	0x00000001	/* Enable TXD for fragments */
+#define AR2315_PCIMISC_CFG_SEL	0x00000002	/* Mem or Config cycles */
+#define AR2315_PCIMISC_GIG_MASK	0x0000000C	/* bits 31-30 for pci req */
+#define AR2315_PCIMISC_RST_MODE	0x00000030
+#define AR2315_PCIRST_INPUT	0x00000000	/* 4:5=0 rst is input */
+#define AR2315_PCIRST_LOW	0x00000010	/* 4:5=1 rst to GND */
+#define AR2315_PCIRST_HIGH	0x00000020	/* 4:5=2 rst to VDD */
+#define AR2315_PCIGRANT_EN	0x00000000	/* 6:7=0 early grant en */
+#define AR2315_PCIGRANT_FRAME	0x00000040	/* 6:7=1 grant waits 4 frame */
+#define AR2315_PCIGRANT_IDLE	0x00000080	/* 6:7=2 grant waits 4 idle */
+#define AR2315_PCIGRANT_GAP	0x00000000	/* 6:7=2 grant waits 4 idle */
+#define AR2315_PCICACHE_DIS	0x00001000	/* PCI external access cache
+						 * disable */
+
+#define AR2315_PCI_OUT_TSTAMP		0x0010
+
+#define AR2315_PCI_UNCACHE_CFG		0x0014
+
+#define AR2315_PCI_IN_EN		0x0100
+
+#define AR2315_PCI_IN_EN0	0x01	/* Enable chain 0 */
+#define AR2315_PCI_IN_EN1	0x02	/* Enable chain 1 */
+#define AR2315_PCI_IN_EN2	0x04	/* Enable chain 2 */
+#define AR2315_PCI_IN_EN3	0x08	/* Enable chain 3 */
+
+#define AR2315_PCI_IN_DIS		0x0104
+
+#define AR2315_PCI_IN_DIS0	0x01	/* Disable chain 0 */
+#define AR2315_PCI_IN_DIS1	0x02	/* Disable chain 1 */
+#define AR2315_PCI_IN_DIS2	0x04	/* Disable chain 2 */
+#define AR2315_PCI_IN_DIS3	0x08	/* Disable chain 3 */
+
+#define AR2315_PCI_IN_PTR		0x0200
+
+#define AR2315_PCI_OUT_EN		0x0400
+
+#define AR2315_PCI_OUT_EN0	0x01	/* Enable chain 0 */
+
+#define AR2315_PCI_OUT_DIS		0x0404
+
+#define AR2315_PCI_OUT_DIS0	0x01	/* Disable chain 0 */
+
+#define AR2315_PCI_OUT_PTR		0x0408
+
+/* PCI interrupt status (write one to clear) */
+#define AR2315_PCI_ISR			0x0500
+
+#define AR2315_PCI_INT_TX	0x00000001	/* Desc In Completed */
+#define AR2315_PCI_INT_TXOK	0x00000002	/* Desc In OK */
+#define AR2315_PCI_INT_TXERR	0x00000004	/* Desc In ERR */
+#define AR2315_PCI_INT_TXEOL	0x00000008	/* Desc In End-of-List */
+#define AR2315_PCI_INT_RX	0x00000010	/* Desc Out Completed */
+#define AR2315_PCI_INT_RXOK	0x00000020	/* Desc Out OK */
+#define AR2315_PCI_INT_RXERR	0x00000040	/* Desc Out ERR */
+#define AR2315_PCI_INT_RXEOL	0x00000080	/* Desc Out EOL */
+#define AR2315_PCI_INT_TXOOD	0x00000200	/* Desc In Out-of-Desc */
+#define AR2315_PCI_INT_DESCMASK	0x0000FFFF	/* Desc Mask */
+#define AR2315_PCI_INT_EXT	0x02000000	/* Extern PCI INTA */
+#define AR2315_PCI_INT_ABORT	0x04000000	/* PCI bus abort event */
+
+/* PCI interrupt mask */
+#define AR2315_PCI_IMR			0x0504
+
+/* Global PCI interrupt enable */
+#define AR2315_PCI_IER			0x0508
+
+#define AR2315_PCI_IER_DISABLE		0x00	/* disable pci interrupts */
+#define AR2315_PCI_IER_ENABLE		0x01	/* enable pci interrupts */
+
+#define AR2315_PCI_HOST_IN_EN		0x0800
+#define AR2315_PCI_HOST_IN_DIS		0x0804
+#define AR2315_PCI_HOST_IN_PTR		0x0810
+#define AR2315_PCI_HOST_OUT_EN		0x0900
+#define AR2315_PCI_HOST_OUT_DIS		0x0904
+#define AR2315_PCI_HOST_OUT_PTR		0x0908
+
+/*
+ * PCI interrupts, which share IP5
+ * Keep ordered according to AR2315_PCI_INT_XXX bits
+ */
+#define AR2315_PCI_IRQ_EXT		25
+#define AR2315_PCI_IRQ_ABORT		26
+#define AR2315_PCI_IRQ_COUNT		27
+
+/* Arbitrary size of memory region to access the configuration space */
+#define AR2315_PCI_CFG_SIZE	0x00100000
+
+#define AR2315_PCI_HOST_SLOT	3
+#define AR2315_PCI_HOST_DEVID	((0xff18 << 16) | PCI_VENDOR_ID_ATHEROS)
+
+/*
+ * We need some arbitrary non-zero value to be programmed to the BAR1 register
+ * of PCI host controller to enable DMA. The same value should be used as the
+ * offset to calculate the physical address of DMA buffer for PCI devices.
+ */
+#define AR2315_PCI_HOST_SDRAM_BASEADDR	0x20000000
+
+/* ??? access BAR */
+#define AR2315_PCI_HOST_MBAR0		0x10000000
+/* RAM access BAR */
+#define AR2315_PCI_HOST_MBAR1		AR2315_PCI_HOST_SDRAM_BASEADDR
+/* ??? access BAR */
+#define AR2315_PCI_HOST_MBAR2		0x30000000
+
+struct ar2315_pci_ctrl {
+	void __iomem *cfg_mem;
+	void __iomem *mmr_mem;
+	unsigned irq;
+	unsigned irq_ext;
+	struct irq_domain *domain;
+	struct pci_controller pci_ctrl;
+	struct resource mem_res;
+	struct resource io_res;
+};
+
+static inline dma_addr_t ar2315_dev_offset(struct device *dev)
+{
+	if (dev && dev_is_pci(dev))
+		return AR2315_PCI_HOST_SDRAM_BASEADDR;
+	return 0;
+}
+
+dma_addr_t phys_to_dma(struct device *dev, phys_addr_t paddr)
+{
+	return paddr + ar2315_dev_offset(dev);
+}
+
+phys_addr_t dma_to_phys(struct device *dev, dma_addr_t dma_addr)
+{
+	return dma_addr - ar2315_dev_offset(dev);
+}
+
+static inline struct ar2315_pci_ctrl *ar2315_pci_bus_to_apc(struct pci_bus *bus)
+{
+	struct pci_controller *hose = bus->sysdata;
+
+	return container_of(hose, struct ar2315_pci_ctrl, pci_ctrl);
+}
+
+static inline u32 ar2315_pci_reg_read(struct ar2315_pci_ctrl *apc, u32 reg)
+{
+	return __raw_readl(apc->mmr_mem + reg);
+}
+
+static inline void ar2315_pci_reg_write(struct ar2315_pci_ctrl *apc, u32 reg,
+					u32 val)
+{
+	__raw_writel(val, apc->mmr_mem + reg);
+}
+
+static inline void ar2315_pci_reg_mask(struct ar2315_pci_ctrl *apc, u32 reg,
+				       u32 mask, u32 val)
+{
+	u32 ret = ar2315_pci_reg_read(apc, reg);
+
+	ret &= ~mask;
+	ret |= val;
+	ar2315_pci_reg_write(apc, reg, ret);
+}
+
+static int ar2315_pci_cfg_access(struct ar2315_pci_ctrl *apc, unsigned devfn,
+				 int where, int size, u32 *ptr, bool write)
+{
+	int func = PCI_FUNC(devfn);
+	int dev = PCI_SLOT(devfn);
+	u32 addr = (1 << (13 + dev)) | (func << 8) | (where & ~3);
+	u32 mask = 0xffffffff >> 8 * (4 - size);
+	u32 sh = (where & 3) * 8;
+	u32 value, isr;
+
+	/* Prevent access past the remapped area */
+	if (addr >= AR2315_PCI_CFG_SIZE || dev > 18)
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	/* Clear pending errors */
+	ar2315_pci_reg_write(apc, AR2315_PCI_ISR, AR2315_PCI_INT_ABORT);
+	/* Select Configuration access */
+	ar2315_pci_reg_mask(apc, AR2315_PCI_MISC_CONFIG, 0,
+			    AR2315_PCIMISC_CFG_SEL);
+
+	mb();	/* PCI must see space change before we begin */
+
+	value = __raw_readl(apc->cfg_mem + addr);
+
+	isr = ar2315_pci_reg_read(apc, AR2315_PCI_ISR);
+
+	if (isr & AR2315_PCI_INT_ABORT)
+		goto exit_err;
+
+	if (write) {
+		value = (value & ~(mask << sh)) | *ptr << sh;
+		__raw_writel(value, apc->cfg_mem + addr);
+		isr = ar2315_pci_reg_read(apc, AR2315_PCI_ISR);
+		if (isr & AR2315_PCI_INT_ABORT)
+			goto exit_err;
+	} else {
+		*ptr = (value >> sh) & mask;
+	}
+
+	goto exit;
+
+exit_err:
+	ar2315_pci_reg_write(apc, AR2315_PCI_ISR, AR2315_PCI_INT_ABORT);
+	if (!write)
+		*ptr = 0xffffffff;
+
+exit:
+	/* Select Memory access */
+	ar2315_pci_reg_mask(apc, AR2315_PCI_MISC_CONFIG, AR2315_PCIMISC_CFG_SEL,
+			    0);
+
+	return isr & AR2315_PCI_INT_ABORT ? PCIBIOS_DEVICE_NOT_FOUND :
+					    PCIBIOS_SUCCESSFUL;
+}
+
+static inline int ar2315_pci_local_cfg_rd(struct ar2315_pci_ctrl *apc,
+					  unsigned devfn, int where, u32 *val)
+{
+	return ar2315_pci_cfg_access(apc, devfn, where, sizeof(u32), val,
+				     false);
+}
+
+static inline int ar2315_pci_local_cfg_wr(struct ar2315_pci_ctrl *apc,
+					  unsigned devfn, int where, u32 val)
+{
+	return ar2315_pci_cfg_access(apc, devfn, where, sizeof(u32), &val,
+				     true);
+}
+
+static int ar2315_pci_cfg_read(struct pci_bus *bus, unsigned devfn, int where,
+			       int size, u32 *value)
+{
+	struct ar2315_pci_ctrl *apc = ar2315_pci_bus_to_apc(bus);
+
+	if (PCI_SLOT(devfn) == AR2315_PCI_HOST_SLOT)
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	return ar2315_pci_cfg_access(apc, devfn, where, size, value, false);
+}
+
+static int ar2315_pci_cfg_write(struct pci_bus *bus, unsigned devfn, int where,
+				int size, u32 value)
+{
+	struct ar2315_pci_ctrl *apc = ar2315_pci_bus_to_apc(bus);
+
+	if (PCI_SLOT(devfn) == AR2315_PCI_HOST_SLOT)
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	return ar2315_pci_cfg_access(apc, devfn, where, size, &value, true);
+}
+
+static struct pci_ops ar2315_pci_ops = {
+	.read	= ar2315_pci_cfg_read,
+	.write	= ar2315_pci_cfg_write,
+};
+
+static int ar2315_pci_host_setup(struct ar2315_pci_ctrl *apc)
+{
+	unsigned devfn = PCI_DEVFN(AR2315_PCI_HOST_SLOT, 0);
+	int res;
+	u32 id;
+
+	res = ar2315_pci_local_cfg_rd(apc, devfn, PCI_VENDOR_ID, &id);
+	if (res != PCIBIOS_SUCCESSFUL || id != AR2315_PCI_HOST_DEVID)
+		return -ENODEV;
+
+	/* Program MBARs */
+	ar2315_pci_local_cfg_wr(apc, devfn, PCI_BASE_ADDRESS_0,
+				AR2315_PCI_HOST_MBAR0);
+	ar2315_pci_local_cfg_wr(apc, devfn, PCI_BASE_ADDRESS_1,
+				AR2315_PCI_HOST_MBAR1);
+	ar2315_pci_local_cfg_wr(apc, devfn, PCI_BASE_ADDRESS_2,
+				AR2315_PCI_HOST_MBAR2);
+
+	/* Run */
+	ar2315_pci_local_cfg_wr(apc, devfn, PCI_COMMAND, PCI_COMMAND_MEMORY |
+				PCI_COMMAND_MASTER | PCI_COMMAND_SPECIAL |
+				PCI_COMMAND_INVALIDATE | PCI_COMMAND_PARITY |
+				PCI_COMMAND_SERR | PCI_COMMAND_FAST_BACK);
+
+	return 0;
+}
+
+static void ar2315_pci_irq_handler(struct irq_desc *desc)
+{
+	struct ar2315_pci_ctrl *apc = irq_desc_get_handler_data(desc);
+	u32 pending = ar2315_pci_reg_read(apc, AR2315_PCI_ISR) &
+		      ar2315_pci_reg_read(apc, AR2315_PCI_IMR);
+	int ret = 0;
+
+	if (pending)
+		ret = generic_handle_domain_irq(apc->domain, __ffs(pending));
+
+	if (!pending || ret)
+		spurious_interrupt();
+}
+
+static void ar2315_pci_irq_mask(struct irq_data *d)
+{
+	struct ar2315_pci_ctrl *apc = irq_data_get_irq_chip_data(d);
+
+	ar2315_pci_reg_mask(apc, AR2315_PCI_IMR, BIT(d->hwirq), 0);
+}
+
+static void ar2315_pci_irq_mask_ack(struct irq_data *d)
+{
+	struct ar2315_pci_ctrl *apc = irq_data_get_irq_chip_data(d);
+	u32 m = BIT(d->hwirq);
+
+	ar2315_pci_reg_mask(apc, AR2315_PCI_IMR, m, 0);
+	ar2315_pci_reg_write(apc, AR2315_PCI_ISR, m);
+}
+
+static void ar2315_pci_irq_unmask(struct irq_data *d)
+{
+	struct ar2315_pci_ctrl *apc = irq_data_get_irq_chip_data(d);
+
+	ar2315_pci_reg_mask(apc, AR2315_PCI_IMR, 0, BIT(d->hwirq));
+}
+
+static struct irq_chip ar2315_pci_irq_chip = {
+	.name = "AR2315-PCI",
+	.irq_mask = ar2315_pci_irq_mask,
+	.irq_mask_ack = ar2315_pci_irq_mask_ack,
+	.irq_unmask = ar2315_pci_irq_unmask,
+};
+
+static int ar2315_pci_irq_map(struct irq_domain *d, unsigned irq,
+			      irq_hw_number_t hw)
+{
+	irq_set_chip_and_handler(irq, &ar2315_pci_irq_chip, handle_level_irq);
+	irq_set_chip_data(irq, d->host_data);
+	return 0;
+}
+
+static const struct irq_domain_ops ar2315_pci_irq_domain_ops = {
+	.map = ar2315_pci_irq_map,
+};
+
+static void ar2315_pci_irq_init(struct ar2315_pci_ctrl *apc)
+{
+	ar2315_pci_reg_mask(apc, AR2315_PCI_IER, AR2315_PCI_IER_ENABLE, 0);
+	ar2315_pci_reg_mask(apc, AR2315_PCI_IMR, (AR2315_PCI_INT_ABORT |
+			    AR2315_PCI_INT_EXT), 0);
+
+	apc->irq_ext = irq_create_mapping(apc->domain, AR2315_PCI_IRQ_EXT);
+
+	irq_set_chained_handler_and_data(apc->irq, ar2315_pci_irq_handler,
+					 apc);
+
+	/* Clear any pending Abort or external Interrupts
+	 * and enable interrupt processing */
+	ar2315_pci_reg_write(apc, AR2315_PCI_ISR, AR2315_PCI_INT_ABORT |
+						  AR2315_PCI_INT_EXT);
+	ar2315_pci_reg_mask(apc, AR2315_PCI_IER, 0, AR2315_PCI_IER_ENABLE);
+}
+
+static int ar2315_pci_probe(struct platform_device *pdev)
+{
+	struct ar2315_pci_ctrl *apc;
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	int irq, err;
+
+	apc = devm_kzalloc(dev, sizeof(*apc), GFP_KERNEL);
+	if (!apc)
+		return -ENOMEM;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0)
+		return -EINVAL;
+	apc->irq = irq;
+
+	apc->mmr_mem = devm_platform_ioremap_resource_byname(pdev,
+							     "ar2315-pci-ctrl");
+	if (IS_ERR(apc->mmr_mem))
+		return PTR_ERR(apc->mmr_mem);
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+					   "ar2315-pci-ext");
+	if (!res)
+		return -EINVAL;
+
+	apc->mem_res.name = "AR2315 PCI mem space";
+	apc->mem_res.parent = res;
+	apc->mem_res.start = res->start;
+	apc->mem_res.end = res->end;
+	apc->mem_res.flags = IORESOURCE_MEM;
+
+	/* Remap PCI config space */
+	apc->cfg_mem = devm_ioremap(dev, res->start,
+					    AR2315_PCI_CFG_SIZE);
+	if (!apc->cfg_mem) {
+		dev_err(dev, "failed to remap PCI config space\n");
+		return -ENOMEM;
+	}
+
+	/* Reset the PCI bus by setting bits 5-4 in PCI_MCFG */
+	ar2315_pci_reg_mask(apc, AR2315_PCI_MISC_CONFIG,
+			    AR2315_PCIMISC_RST_MODE,
+			    AR2315_PCIRST_LOW);
+	msleep(100);
+
+	/* Bring the PCI out of reset */
+	ar2315_pci_reg_mask(apc, AR2315_PCI_MISC_CONFIG,
+			    AR2315_PCIMISC_RST_MODE,
+			    AR2315_PCIRST_HIGH | AR2315_PCICACHE_DIS | 0x8);
+
+	ar2315_pci_reg_write(apc, AR2315_PCI_UNCACHE_CFG,
+			     0x1E | /* 1GB uncached */
+			     (1 << 5) | /* Enable uncached */
+			     (0x2 << 30) /* Base: 0x80000000 */);
+	ar2315_pci_reg_read(apc, AR2315_PCI_UNCACHE_CFG);
+
+	msleep(500);
+
+	err = ar2315_pci_host_setup(apc);
+	if (err)
+		return err;
+
+	apc->domain = irq_domain_add_linear(NULL, AR2315_PCI_IRQ_COUNT,
+					    &ar2315_pci_irq_domain_ops, apc);
+	if (!apc->domain) {
+		dev_err(dev, "failed to add IRQ domain\n");
+		return -ENOMEM;
+	}
+
+	ar2315_pci_irq_init(apc);
+
+	/* PCI controller does not support I/O ports */
+	apc->io_res.name = "AR2315 IO space";
+	apc->io_res.start = 0;
+	apc->io_res.end = 0;
+	apc->io_res.flags = IORESOURCE_IO;
+
+	apc->pci_ctrl.pci_ops = &ar2315_pci_ops;
+	apc->pci_ctrl.mem_resource = &apc->mem_res;
+	apc->pci_ctrl.io_resource = &apc->io_res;
+
+	register_pci_controller(&apc->pci_ctrl);
+
+	dev_info(dev, "register PCI controller\n");
+
+	return 0;
+}
+
+static struct platform_driver ar2315_pci_driver = {
+	.probe = ar2315_pci_probe,
+	.driver = {
+		.name = "ar2315-pci",
+	},
+};
+
+static int __init ar2315_pci_init(void)
+{
+	return platform_driver_register(&ar2315_pci_driver);
+}
+arch_initcall(ar2315_pci_init);
+
+int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	struct ar2315_pci_ctrl *apc = ar2315_pci_bus_to_apc(dev->bus);
+
+	return slot ? 0 : apc->irq_ext;
+}
+
+int pcibios_plat_dev_init(struct pci_dev *dev)
+{
+	return 0;
+}
diff --git a/arch/mips/pci/pci-ar71xx.c b/arch/mips/pci/pci-ar71xx.c
new file mode 100644
index 000000000..118760b3f
--- /dev/null
+++ b/arch/mips/pci/pci-ar71xx.c
@@ -0,0 +1,401 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *  Atheros AR71xx PCI host controller driver
+ *
+ *  Copyright (C) 2008-2011 Gabor Juhos <juhosg@openwrt.org>
+ *  Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ *
+ *  Parts of this file are based on Atheros' 2.6.15 BSP
+ */
+
+#include <linux/resource.h>
+#include <linux/types.h>
+#include <linux/delay.h>
+#include <linux/bitops.h>
+#include <linux/pci.h>
+#include <linux/pci_regs.h>
+#include <linux/interrupt.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+
+#include <asm/mach-ath79/ar71xx_regs.h>
+#include <asm/mach-ath79/ath79.h>
+
+#define AR71XX_PCI_REG_CRP_AD_CBE	0x00
+#define AR71XX_PCI_REG_CRP_WRDATA	0x04
+#define AR71XX_PCI_REG_CRP_RDDATA	0x08
+#define AR71XX_PCI_REG_CFG_AD		0x0c
+#define AR71XX_PCI_REG_CFG_CBE		0x10
+#define AR71XX_PCI_REG_CFG_WRDATA	0x14
+#define AR71XX_PCI_REG_CFG_RDDATA	0x18
+#define AR71XX_PCI_REG_PCI_ERR		0x1c
+#define AR71XX_PCI_REG_PCI_ERR_ADDR	0x20
+#define AR71XX_PCI_REG_AHB_ERR		0x24
+#define AR71XX_PCI_REG_AHB_ERR_ADDR	0x28
+
+#define AR71XX_PCI_CRP_CMD_WRITE	0x00010000
+#define AR71XX_PCI_CRP_CMD_READ		0x00000000
+#define AR71XX_PCI_CFG_CMD_READ		0x0000000a
+#define AR71XX_PCI_CFG_CMD_WRITE	0x0000000b
+
+#define AR71XX_PCI_INT_CORE		BIT(4)
+#define AR71XX_PCI_INT_DEV2		BIT(2)
+#define AR71XX_PCI_INT_DEV1		BIT(1)
+#define AR71XX_PCI_INT_DEV0		BIT(0)
+
+#define AR71XX_PCI_IRQ_COUNT		5
+
+struct ar71xx_pci_controller {
+	void __iomem *cfg_base;
+	int irq;
+	int irq_base;
+	struct pci_controller pci_ctrl;
+	struct resource io_res;
+	struct resource mem_res;
+};
+
+/* Byte lane enable bits */
+static const u8 ar71xx_pci_ble_table[4][4] = {
+	{0x0, 0xf, 0xf, 0xf},
+	{0xe, 0xd, 0xb, 0x7},
+	{0xc, 0xf, 0x3, 0xf},
+	{0xf, 0xf, 0xf, 0xf},
+};
+
+static const u32 ar71xx_pci_read_mask[8] = {
+	0, 0xff, 0xffff, 0, 0xffffffff, 0, 0, 0
+};
+
+static inline u32 ar71xx_pci_get_ble(int where, int size, int local)
+{
+	u32 t;
+
+	t = ar71xx_pci_ble_table[size & 3][where & 3];
+	BUG_ON(t == 0xf);
+	t <<= (local) ? 20 : 4;
+
+	return t;
+}
+
+static inline u32 ar71xx_pci_bus_addr(struct pci_bus *bus, unsigned int devfn,
+				      int where)
+{
+	u32 ret;
+
+	if (!bus->number) {
+		/* type 0 */
+		ret = (1 << PCI_SLOT(devfn)) | (PCI_FUNC(devfn) << 8) |
+		      (where & ~3);
+	} else {
+		/* type 1 */
+		ret = (bus->number << 16) | (PCI_SLOT(devfn) << 11) |
+		      (PCI_FUNC(devfn) << 8) | (where & ~3) | 1;
+	}
+
+	return ret;
+}
+
+static inline struct ar71xx_pci_controller *
+pci_bus_to_ar71xx_controller(struct pci_bus *bus)
+{
+	struct pci_controller *hose;
+
+	hose = (struct pci_controller *) bus->sysdata;
+	return container_of(hose, struct ar71xx_pci_controller, pci_ctrl);
+}
+
+static int ar71xx_pci_check_error(struct ar71xx_pci_controller *apc, int quiet)
+{
+	void __iomem *base = apc->cfg_base;
+	u32 pci_err;
+	u32 ahb_err;
+
+	pci_err = __raw_readl(base + AR71XX_PCI_REG_PCI_ERR) & 3;
+	if (pci_err) {
+		if (!quiet) {
+			u32 addr;
+
+			addr = __raw_readl(base + AR71XX_PCI_REG_PCI_ERR_ADDR);
+			pr_crit("ar71xx: %s bus error %d at addr 0x%x\n",
+				"PCI", pci_err, addr);
+		}
+
+		/* clear PCI error status */
+		__raw_writel(pci_err, base + AR71XX_PCI_REG_PCI_ERR);
+	}
+
+	ahb_err = __raw_readl(base + AR71XX_PCI_REG_AHB_ERR) & 1;
+	if (ahb_err) {
+		if (!quiet) {
+			u32 addr;
+
+			addr = __raw_readl(base + AR71XX_PCI_REG_AHB_ERR_ADDR);
+			pr_crit("ar71xx: %s bus error %d at addr 0x%x\n",
+				"AHB", ahb_err, addr);
+		}
+
+		/* clear AHB error status */
+		__raw_writel(ahb_err, base + AR71XX_PCI_REG_AHB_ERR);
+	}
+
+	return !!(ahb_err | pci_err);
+}
+
+static inline void ar71xx_pci_local_write(struct ar71xx_pci_controller *apc,
+					  int where, int size, u32 value)
+{
+	void __iomem *base = apc->cfg_base;
+	u32 ad_cbe;
+
+	value = value << (8 * (where & 3));
+
+	ad_cbe = AR71XX_PCI_CRP_CMD_WRITE | (where & ~3);
+	ad_cbe |= ar71xx_pci_get_ble(where, size, 1);
+
+	__raw_writel(ad_cbe, base + AR71XX_PCI_REG_CRP_AD_CBE);
+	__raw_writel(value, base + AR71XX_PCI_REG_CRP_WRDATA);
+}
+
+static inline int ar71xx_pci_set_cfgaddr(struct pci_bus *bus,
+					 unsigned int devfn,
+					 int where, int size, u32 cmd)
+{
+	struct ar71xx_pci_controller *apc = pci_bus_to_ar71xx_controller(bus);
+	void __iomem *base = apc->cfg_base;
+	u32 addr;
+
+	addr = ar71xx_pci_bus_addr(bus, devfn, where);
+
+	__raw_writel(addr, base + AR71XX_PCI_REG_CFG_AD);
+	__raw_writel(cmd | ar71xx_pci_get_ble(where, size, 0),
+		     base + AR71XX_PCI_REG_CFG_CBE);
+
+	return ar71xx_pci_check_error(apc, 1);
+}
+
+static int ar71xx_pci_read_config(struct pci_bus *bus, unsigned int devfn,
+				  int where, int size, u32 *value)
+{
+	struct ar71xx_pci_controller *apc = pci_bus_to_ar71xx_controller(bus);
+	void __iomem *base = apc->cfg_base;
+	u32 data;
+	int err;
+	int ret;
+
+	ret = PCIBIOS_SUCCESSFUL;
+	data = ~0;
+
+	err = ar71xx_pci_set_cfgaddr(bus, devfn, where, size,
+				     AR71XX_PCI_CFG_CMD_READ);
+	if (err)
+		ret = PCIBIOS_DEVICE_NOT_FOUND;
+	else
+		data = __raw_readl(base + AR71XX_PCI_REG_CFG_RDDATA);
+
+	*value = (data >> (8 * (where & 3))) & ar71xx_pci_read_mask[size & 7];
+
+	return ret;
+}
+
+static int ar71xx_pci_write_config(struct pci_bus *bus, unsigned int devfn,
+				   int where, int size, u32 value)
+{
+	struct ar71xx_pci_controller *apc = pci_bus_to_ar71xx_controller(bus);
+	void __iomem *base = apc->cfg_base;
+	int err;
+	int ret;
+
+	value = value << (8 * (where & 3));
+	ret = PCIBIOS_SUCCESSFUL;
+
+	err = ar71xx_pci_set_cfgaddr(bus, devfn, where, size,
+				     AR71XX_PCI_CFG_CMD_WRITE);
+	if (err)
+		ret = PCIBIOS_DEVICE_NOT_FOUND;
+	else
+		__raw_writel(value, base + AR71XX_PCI_REG_CFG_WRDATA);
+
+	return ret;
+}
+
+static struct pci_ops ar71xx_pci_ops = {
+	.read	= ar71xx_pci_read_config,
+	.write	= ar71xx_pci_write_config,
+};
+
+static void ar71xx_pci_irq_handler(struct irq_desc *desc)
+{
+	struct ar71xx_pci_controller *apc;
+	void __iomem *base = ath79_reset_base;
+	u32 pending;
+
+	apc = irq_desc_get_handler_data(desc);
+
+	pending = __raw_readl(base + AR71XX_RESET_REG_PCI_INT_STATUS) &
+		  __raw_readl(base + AR71XX_RESET_REG_PCI_INT_ENABLE);
+
+	if (pending & AR71XX_PCI_INT_DEV0)
+		generic_handle_irq(apc->irq_base + 0);
+
+	else if (pending & AR71XX_PCI_INT_DEV1)
+		generic_handle_irq(apc->irq_base + 1);
+
+	else if (pending & AR71XX_PCI_INT_DEV2)
+		generic_handle_irq(apc->irq_base + 2);
+
+	else if (pending & AR71XX_PCI_INT_CORE)
+		generic_handle_irq(apc->irq_base + 4);
+
+	else
+		spurious_interrupt();
+}
+
+static void ar71xx_pci_irq_unmask(struct irq_data *d)
+{
+	struct ar71xx_pci_controller *apc;
+	unsigned int irq;
+	void __iomem *base = ath79_reset_base;
+	u32 t;
+
+	apc = irq_data_get_irq_chip_data(d);
+	irq = d->irq - apc->irq_base;
+
+	t = __raw_readl(base + AR71XX_RESET_REG_PCI_INT_ENABLE);
+	__raw_writel(t | (1 << irq), base + AR71XX_RESET_REG_PCI_INT_ENABLE);
+
+	/* flush write */
+	__raw_readl(base + AR71XX_RESET_REG_PCI_INT_ENABLE);
+}
+
+static void ar71xx_pci_irq_mask(struct irq_data *d)
+{
+	struct ar71xx_pci_controller *apc;
+	unsigned int irq;
+	void __iomem *base = ath79_reset_base;
+	u32 t;
+
+	apc = irq_data_get_irq_chip_data(d);
+	irq = d->irq - apc->irq_base;
+
+	t = __raw_readl(base + AR71XX_RESET_REG_PCI_INT_ENABLE);
+	__raw_writel(t & ~(1 << irq), base + AR71XX_RESET_REG_PCI_INT_ENABLE);
+
+	/* flush write */
+	__raw_readl(base + AR71XX_RESET_REG_PCI_INT_ENABLE);
+}
+
+static struct irq_chip ar71xx_pci_irq_chip = {
+	.name		= "AR71XX PCI",
+	.irq_mask	= ar71xx_pci_irq_mask,
+	.irq_unmask	= ar71xx_pci_irq_unmask,
+	.irq_mask_ack	= ar71xx_pci_irq_mask,
+};
+
+static void ar71xx_pci_irq_init(struct ar71xx_pci_controller *apc)
+{
+	void __iomem *base = ath79_reset_base;
+	int i;
+
+	__raw_writel(0, base + AR71XX_RESET_REG_PCI_INT_ENABLE);
+	__raw_writel(0, base + AR71XX_RESET_REG_PCI_INT_STATUS);
+
+	BUILD_BUG_ON(ATH79_PCI_IRQ_COUNT < AR71XX_PCI_IRQ_COUNT);
+
+	apc->irq_base = ATH79_PCI_IRQ_BASE;
+	for (i = apc->irq_base;
+	     i < apc->irq_base + AR71XX_PCI_IRQ_COUNT; i++) {
+		irq_set_chip_and_handler(i, &ar71xx_pci_irq_chip,
+					 handle_level_irq);
+		irq_set_chip_data(i, apc);
+	}
+
+	irq_set_chained_handler_and_data(apc->irq, ar71xx_pci_irq_handler,
+					 apc);
+}
+
+static void ar71xx_pci_reset(void)
+{
+	ath79_device_reset_set(AR71XX_RESET_PCI_BUS | AR71XX_RESET_PCI_CORE);
+	mdelay(100);
+
+	ath79_device_reset_clear(AR71XX_RESET_PCI_BUS | AR71XX_RESET_PCI_CORE);
+	mdelay(100);
+
+	ath79_ddr_set_pci_windows();
+	mdelay(100);
+}
+
+static int ar71xx_pci_probe(struct platform_device *pdev)
+{
+	struct ar71xx_pci_controller *apc;
+	struct resource *res;
+	u32 t;
+
+	apc = devm_kzalloc(&pdev->dev, sizeof(struct ar71xx_pci_controller),
+			   GFP_KERNEL);
+	if (!apc)
+		return -ENOMEM;
+
+	apc->cfg_base = devm_platform_ioremap_resource_byname(pdev,
+							      "cfg_base");
+	if (IS_ERR(apc->cfg_base))
+		return PTR_ERR(apc->cfg_base);
+
+	apc->irq = platform_get_irq(pdev, 0);
+	if (apc->irq < 0)
+		return -EINVAL;
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_IO, "io_base");
+	if (!res)
+		return -EINVAL;
+
+	apc->io_res.parent = res;
+	apc->io_res.name = "PCI IO space";
+	apc->io_res.start = res->start;
+	apc->io_res.end = res->end;
+	apc->io_res.flags = IORESOURCE_IO;
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "mem_base");
+	if (!res)
+		return -EINVAL;
+
+	apc->mem_res.parent = res;
+	apc->mem_res.name = "PCI memory space";
+	apc->mem_res.start = res->start;
+	apc->mem_res.end = res->end;
+	apc->mem_res.flags = IORESOURCE_MEM;
+
+	ar71xx_pci_reset();
+
+	/* setup COMMAND register */
+	t = PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER | PCI_COMMAND_INVALIDATE
+	  | PCI_COMMAND_PARITY | PCI_COMMAND_SERR | PCI_COMMAND_FAST_BACK;
+	ar71xx_pci_local_write(apc, PCI_COMMAND, 4, t);
+
+	/* clear bus errors */
+	ar71xx_pci_check_error(apc, 1);
+
+	ar71xx_pci_irq_init(apc);
+
+	apc->pci_ctrl.pci_ops = &ar71xx_pci_ops;
+	apc->pci_ctrl.mem_resource = &apc->mem_res;
+	apc->pci_ctrl.io_resource = &apc->io_res;
+
+	register_pci_controller(&apc->pci_ctrl);
+
+	return 0;
+}
+
+static struct platform_driver ar71xx_pci_driver = {
+	.probe = ar71xx_pci_probe,
+	.driver = {
+		.name = "ar71xx-pci",
+	},
+};
+
+static int __init ar71xx_pci_init(void)
+{
+	return platform_driver_register(&ar71xx_pci_driver);
+}
+
+postcore_initcall(ar71xx_pci_init);
diff --git a/arch/mips/pci/pci-ar724x.c b/arch/mips/pci/pci-ar724x.c
new file mode 100644
index 000000000..807558b25
--- /dev/null
+++ b/arch/mips/pci/pci-ar724x.c
@@ -0,0 +1,447 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *  Atheros AR724X PCI host controller driver
+ *
+ *  Copyright (C) 2011 René Bolldorf <xsecute@googlemail.com>
+ *  Copyright (C) 2009-2011 Gabor Juhos <juhosg@openwrt.org>
+ */
+
+#include <linux/irq.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <asm/mach-ath79/ath79.h>
+#include <asm/mach-ath79/ar71xx_regs.h>
+
+#define AR724X_PCI_REG_APP		0x00
+#define AR724X_PCI_REG_RESET		0x18
+#define AR724X_PCI_REG_INT_STATUS	0x4c
+#define AR724X_PCI_REG_INT_MASK		0x50
+
+#define AR724X_PCI_APP_LTSSM_ENABLE	BIT(0)
+
+#define AR724X_PCI_RESET_LINK_UP	BIT(0)
+
+#define AR724X_PCI_INT_DEV0		BIT(14)
+
+#define AR724X_PCI_IRQ_COUNT		1
+
+#define AR7240_BAR0_WAR_VALUE	0xffff
+
+#define AR724X_PCI_CMD_INIT	(PCI_COMMAND_MEMORY |		\
+				 PCI_COMMAND_MASTER |		\
+				 PCI_COMMAND_INVALIDATE |	\
+				 PCI_COMMAND_PARITY |		\
+				 PCI_COMMAND_SERR |		\
+				 PCI_COMMAND_FAST_BACK)
+
+struct ar724x_pci_controller {
+	void __iomem *devcfg_base;
+	void __iomem *ctrl_base;
+	void __iomem *crp_base;
+
+	int irq;
+	int irq_base;
+
+	bool link_up;
+	bool bar0_is_cached;
+	u32  bar0_value;
+
+	struct pci_controller pci_controller;
+	struct resource io_res;
+	struct resource mem_res;
+};
+
+static inline bool ar724x_pci_check_link(struct ar724x_pci_controller *apc)
+{
+	u32 reset;
+
+	reset = __raw_readl(apc->ctrl_base + AR724X_PCI_REG_RESET);
+	return reset & AR724X_PCI_RESET_LINK_UP;
+}
+
+static inline struct ar724x_pci_controller *
+pci_bus_to_ar724x_controller(struct pci_bus *bus)
+{
+	struct pci_controller *hose;
+
+	hose = (struct pci_controller *) bus->sysdata;
+	return container_of(hose, struct ar724x_pci_controller, pci_controller);
+}
+
+static int ar724x_pci_local_write(struct ar724x_pci_controller *apc,
+				  int where, int size, u32 value)
+{
+	void __iomem *base;
+	u32 data;
+	int s;
+
+	WARN_ON(where & (size - 1));
+
+	if (!apc->link_up)
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	base = apc->crp_base;
+	data = __raw_readl(base + (where & ~3));
+
+	switch (size) {
+	case 1:
+		s = ((where & 3) * 8);
+		data &= ~(0xff << s);
+		data |= ((value & 0xff) << s);
+		break;
+	case 2:
+		s = ((where & 2) * 8);
+		data &= ~(0xffff << s);
+		data |= ((value & 0xffff) << s);
+		break;
+	case 4:
+		data = value;
+		break;
+	default:
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+	}
+
+	__raw_writel(data, base + (where & ~3));
+	/* flush write */
+	__raw_readl(base + (where & ~3));
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int ar724x_pci_read(struct pci_bus *bus, unsigned int devfn, int where,
+			    int size, uint32_t *value)
+{
+	struct ar724x_pci_controller *apc;
+	void __iomem *base;
+	u32 data;
+
+	apc = pci_bus_to_ar724x_controller(bus);
+	if (!apc->link_up)
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	if (devfn)
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	base = apc->devcfg_base;
+	data = __raw_readl(base + (where & ~3));
+
+	switch (size) {
+	case 1:
+		if (where & 1)
+			data >>= 8;
+		if (where & 2)
+			data >>= 16;
+		data &= 0xff;
+		break;
+	case 2:
+		if (where & 2)
+			data >>= 16;
+		data &= 0xffff;
+		break;
+	case 4:
+		break;
+	default:
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+	}
+
+	if (where == PCI_BASE_ADDRESS_0 && size == 4 &&
+	    apc->bar0_is_cached) {
+		/* use the cached value */
+		*value = apc->bar0_value;
+	} else {
+		*value = data;
+	}
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int ar724x_pci_write(struct pci_bus *bus, unsigned int devfn, int where,
+			     int size, uint32_t value)
+{
+	struct ar724x_pci_controller *apc;
+	void __iomem *base;
+	u32 data;
+	int s;
+
+	apc = pci_bus_to_ar724x_controller(bus);
+	if (!apc->link_up)
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	if (devfn)
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	if (soc_is_ar7240() && where == PCI_BASE_ADDRESS_0 && size == 4) {
+		if (value != 0xffffffff) {
+			/*
+			 * WAR for a hw issue. If the BAR0 register of the
+			 * device is set to the proper base address, the
+			 * memory space of the device is not accessible.
+			 *
+			 * Cache the intended value so it can be read back,
+			 * and write a SoC specific constant value to the
+			 * BAR0 register in order to make the device memory
+			 * accessible.
+			 */
+			apc->bar0_is_cached = true;
+			apc->bar0_value = value;
+
+			value = AR7240_BAR0_WAR_VALUE;
+		} else {
+			apc->bar0_is_cached = false;
+		}
+	}
+
+	base = apc->devcfg_base;
+	data = __raw_readl(base + (where & ~3));
+
+	switch (size) {
+	case 1:
+		s = ((where & 3) * 8);
+		data &= ~(0xff << s);
+		data |= ((value & 0xff) << s);
+		break;
+	case 2:
+		s = ((where & 2) * 8);
+		data &= ~(0xffff << s);
+		data |= ((value & 0xffff) << s);
+		break;
+	case 4:
+		data = value;
+		break;
+	default:
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+	}
+
+	__raw_writel(data, base + (where & ~3));
+	/* flush write */
+	__raw_readl(base + (where & ~3));
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static struct pci_ops ar724x_pci_ops = {
+	.read	= ar724x_pci_read,
+	.write	= ar724x_pci_write,
+};
+
+static void ar724x_pci_irq_handler(struct irq_desc *desc)
+{
+	struct ar724x_pci_controller *apc;
+	void __iomem *base;
+	u32 pending;
+
+	apc = irq_desc_get_handler_data(desc);
+	base = apc->ctrl_base;
+
+	pending = __raw_readl(base + AR724X_PCI_REG_INT_STATUS) &
+		  __raw_readl(base + AR724X_PCI_REG_INT_MASK);
+
+	if (pending & AR724X_PCI_INT_DEV0)
+		generic_handle_irq(apc->irq_base + 0);
+
+	else
+		spurious_interrupt();
+}
+
+static void ar724x_pci_irq_unmask(struct irq_data *d)
+{
+	struct ar724x_pci_controller *apc;
+	void __iomem *base;
+	int offset;
+	u32 t;
+
+	apc = irq_data_get_irq_chip_data(d);
+	base = apc->ctrl_base;
+	offset = apc->irq_base - d->irq;
+
+	switch (offset) {
+	case 0:
+		t = __raw_readl(base + AR724X_PCI_REG_INT_MASK);
+		__raw_writel(t | AR724X_PCI_INT_DEV0,
+			     base + AR724X_PCI_REG_INT_MASK);
+		/* flush write */
+		__raw_readl(base + AR724X_PCI_REG_INT_MASK);
+	}
+}
+
+static void ar724x_pci_irq_mask(struct irq_data *d)
+{
+	struct ar724x_pci_controller *apc;
+	void __iomem *base;
+	int offset;
+	u32 t;
+
+	apc = irq_data_get_irq_chip_data(d);
+	base = apc->ctrl_base;
+	offset = apc->irq_base - d->irq;
+
+	switch (offset) {
+	case 0:
+		t = __raw_readl(base + AR724X_PCI_REG_INT_MASK);
+		__raw_writel(t & ~AR724X_PCI_INT_DEV0,
+			     base + AR724X_PCI_REG_INT_MASK);
+
+		/* flush write */
+		__raw_readl(base + AR724X_PCI_REG_INT_MASK);
+
+		t = __raw_readl(base + AR724X_PCI_REG_INT_STATUS);
+		__raw_writel(t | AR724X_PCI_INT_DEV0,
+			     base + AR724X_PCI_REG_INT_STATUS);
+
+		/* flush write */
+		__raw_readl(base + AR724X_PCI_REG_INT_STATUS);
+	}
+}
+
+static struct irq_chip ar724x_pci_irq_chip = {
+	.name		= "AR724X PCI ",
+	.irq_mask	= ar724x_pci_irq_mask,
+	.irq_unmask	= ar724x_pci_irq_unmask,
+	.irq_mask_ack	= ar724x_pci_irq_mask,
+};
+
+static void ar724x_pci_irq_init(struct ar724x_pci_controller *apc,
+				int id)
+{
+	void __iomem *base;
+	int i;
+
+	base = apc->ctrl_base;
+
+	__raw_writel(0, base + AR724X_PCI_REG_INT_MASK);
+	__raw_writel(0, base + AR724X_PCI_REG_INT_STATUS);
+
+	apc->irq_base = ATH79_PCI_IRQ_BASE + (id * AR724X_PCI_IRQ_COUNT);
+
+	for (i = apc->irq_base;
+	     i < apc->irq_base + AR724X_PCI_IRQ_COUNT; i++) {
+		irq_set_chip_and_handler(i, &ar724x_pci_irq_chip,
+					 handle_level_irq);
+		irq_set_chip_data(i, apc);
+	}
+
+	irq_set_chained_handler_and_data(apc->irq, ar724x_pci_irq_handler,
+					 apc);
+}
+
+static void ar724x_pci_hw_init(struct ar724x_pci_controller *apc)
+{
+	u32 ppl, app;
+	int wait = 0;
+
+	/* deassert PCIe host controller and PCIe PHY reset */
+	ath79_device_reset_clear(AR724X_RESET_PCIE);
+	ath79_device_reset_clear(AR724X_RESET_PCIE_PHY);
+
+	/* remove the reset of the PCIE PLL */
+	ppl = ath79_pll_rr(AR724X_PLL_REG_PCIE_CONFIG);
+	ppl &= ~AR724X_PLL_REG_PCIE_CONFIG_PPL_RESET;
+	ath79_pll_wr(AR724X_PLL_REG_PCIE_CONFIG, ppl);
+
+	/* deassert bypass for the PCIE PLL */
+	ppl = ath79_pll_rr(AR724X_PLL_REG_PCIE_CONFIG);
+	ppl &= ~AR724X_PLL_REG_PCIE_CONFIG_PPL_BYPASS;
+	ath79_pll_wr(AR724X_PLL_REG_PCIE_CONFIG, ppl);
+
+	/* set PCIE Application Control to ready */
+	app = __raw_readl(apc->ctrl_base + AR724X_PCI_REG_APP);
+	app |= AR724X_PCI_APP_LTSSM_ENABLE;
+	__raw_writel(app, apc->ctrl_base + AR724X_PCI_REG_APP);
+
+	/* wait up to 100ms for PHY link up */
+	do {
+		mdelay(10);
+		wait++;
+	} while (wait < 10 && !ar724x_pci_check_link(apc));
+}
+
+static int ar724x_pci_probe(struct platform_device *pdev)
+{
+	struct ar724x_pci_controller *apc;
+	struct resource *res;
+	int id;
+
+	id = pdev->id;
+	if (id == -1)
+		id = 0;
+
+	apc = devm_kzalloc(&pdev->dev, sizeof(struct ar724x_pci_controller),
+			    GFP_KERNEL);
+	if (!apc)
+		return -ENOMEM;
+
+	apc->ctrl_base = devm_platform_ioremap_resource_byname(pdev, "ctrl_base");
+	if (IS_ERR(apc->ctrl_base))
+		return PTR_ERR(apc->ctrl_base);
+
+	apc->devcfg_base = devm_platform_ioremap_resource_byname(pdev, "cfg_base");
+	if (IS_ERR(apc->devcfg_base))
+		return PTR_ERR(apc->devcfg_base);
+
+	apc->crp_base = devm_platform_ioremap_resource_byname(pdev, "crp_base");
+	if (IS_ERR(apc->crp_base))
+		return PTR_ERR(apc->crp_base);
+
+	apc->irq = platform_get_irq(pdev, 0);
+	if (apc->irq < 0)
+		return -EINVAL;
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_IO, "io_base");
+	if (!res)
+		return -EINVAL;
+
+	apc->io_res.parent = res;
+	apc->io_res.name = "PCI IO space";
+	apc->io_res.start = res->start;
+	apc->io_res.end = res->end;
+	apc->io_res.flags = IORESOURCE_IO;
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "mem_base");
+	if (!res)
+		return -EINVAL;
+
+	apc->mem_res.parent = res;
+	apc->mem_res.name = "PCI memory space";
+	apc->mem_res.start = res->start;
+	apc->mem_res.end = res->end;
+	apc->mem_res.flags = IORESOURCE_MEM;
+
+	apc->pci_controller.pci_ops = &ar724x_pci_ops;
+	apc->pci_controller.io_resource = &apc->io_res;
+	apc->pci_controller.mem_resource = &apc->mem_res;
+
+	/*
+	 * Do the full PCIE Root Complex Initialization Sequence if the PCIe
+	 * host controller is in reset.
+	 */
+	if (ath79_reset_rr(AR724X_RESET_REG_RESET_MODULE) & AR724X_RESET_PCIE)
+		ar724x_pci_hw_init(apc);
+
+	apc->link_up = ar724x_pci_check_link(apc);
+	if (!apc->link_up)
+		dev_warn(&pdev->dev, "PCIe link is down\n");
+
+	ar724x_pci_irq_init(apc, id);
+
+	ar724x_pci_local_write(apc, PCI_COMMAND, 4, AR724X_PCI_CMD_INIT);
+
+	register_pci_controller(&apc->pci_controller);
+
+	return 0;
+}
+
+static struct platform_driver ar724x_pci_driver = {
+	.probe = ar724x_pci_probe,
+	.driver = {
+		.name = "ar724x-pci",
+	},
+};
+
+static int __init ar724x_pci_init(void)
+{
+	return platform_driver_register(&ar724x_pci_driver);
+}
+
+postcore_initcall(ar724x_pci_init);
diff --git a/arch/mips/pci/pci-bcm1480.c b/arch/mips/pci/pci-bcm1480.c
new file mode 100644
index 000000000..db0d4d22d
--- /dev/null
+++ b/arch/mips/pci/pci-bcm1480.c
@@ -0,0 +1,255 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2001,2002,2005 Broadcom Corporation
+ * Copyright (C) 2004 by Ralf Baechle (ralf@linux-mips.org)
+ */
+
+/*
+ * BCM1x80/1x55-specific PCI support
+ *
+ * This module provides the glue between Linux's PCI subsystem
+ * and the hardware.  We basically provide glue for accessing
+ * configuration space, and set up the translation for I/O
+ * space accesses.
+ *
+ * To access configuration space, we use ioremap.  In the 32-bit
+ * kernel, this consumes either 4 or 8 page table pages, and 16MB of
+ * kernel mapped memory.  Hopefully neither of these should be a huge
+ * problem.
+ *
+ * XXX: AT THIS TIME, ONLY the NATIVE PCI-X INTERFACE IS SUPPORTED.
+ */
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/console.h>
+#include <linux/tty.h>
+#include <linux/vt.h>
+
+#include <asm/sibyte/bcm1480_regs.h>
+#include <asm/sibyte/bcm1480_scd.h>
+#include <asm/sibyte/board.h>
+#include <asm/io.h>
+
+/*
+ * Macros for calculating offsets into config space given a device
+ * structure or dev/fun/reg
+ */
+#define CFGOFFSET(bus, devfn, where) (((bus)<<16)+((devfn)<<8)+(where))
+#define CFGADDR(bus, devfn, where)   CFGOFFSET((bus)->number, (devfn), where)
+
+static void *cfg_space;
+
+#define PCI_BUS_ENABLED 1
+#define PCI_DEVICE_MODE 2
+
+static int bcm1480_bus_status;
+
+#define PCI_BRIDGE_DEVICE  0
+
+/*
+ * Read/write 32-bit values in config space.
+ */
+static inline u32 READCFG32(u32 addr)
+{
+	return *(u32 *)(cfg_space + (addr&~3));
+}
+
+static inline void WRITECFG32(u32 addr, u32 data)
+{
+	*(u32 *)(cfg_space + (addr & ~3)) = data;
+}
+
+int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	if (pin == 0)
+		return -1;
+
+	return K_BCM1480_INT_PCI_INTA - 1 + pin;
+}
+
+/* Do platform specific device initialization at pci_enable_device() time */
+int pcibios_plat_dev_init(struct pci_dev *dev)
+{
+	return 0;
+}
+
+/*
+ * Some checks before doing config cycles:
+ * In PCI Device Mode, hide everything on bus 0 except the LDT host
+ * bridge.  Otherwise, access is controlled by bridge MasterEn bits.
+ */
+static int bcm1480_pci_can_access(struct pci_bus *bus, int devfn)
+{
+	u32 devno;
+
+	if (!(bcm1480_bus_status & (PCI_BUS_ENABLED | PCI_DEVICE_MODE)))
+		return 0;
+
+	if (bus->number == 0) {
+		devno = PCI_SLOT(devfn);
+		if (bcm1480_bus_status & PCI_DEVICE_MODE)
+			return 0;
+		else
+			return 1;
+	} else
+		return 1;
+}
+
+/*
+ * Read/write access functions for various sizes of values
+ * in config space.  Return all 1's for disallowed accesses
+ * for a kludgy but adequate simulation of master aborts.
+ */
+
+static int bcm1480_pcibios_read(struct pci_bus *bus, unsigned int devfn,
+				int where, int size, u32 * val)
+{
+	u32 data = 0;
+
+	if ((size == 2) && (where & 1))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+	else if ((size == 4) && (where & 3))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+
+	if (bcm1480_pci_can_access(bus, devfn))
+		data = READCFG32(CFGADDR(bus, devfn, where));
+	else
+		data = 0xFFFFFFFF;
+
+	if (size == 1)
+		*val = (data >> ((where & 3) << 3)) & 0xff;
+	else if (size == 2)
+		*val = (data >> ((where & 3) << 3)) & 0xffff;
+	else
+		*val = data;
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int bcm1480_pcibios_write(struct pci_bus *bus, unsigned int devfn,
+				int where, int size, u32 val)
+{
+	u32 cfgaddr = CFGADDR(bus, devfn, where);
+	u32 data = 0;
+
+	if ((size == 2) && (where & 1))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+	else if ((size == 4) && (where & 3))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+
+	if (!bcm1480_pci_can_access(bus, devfn))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+
+	data = READCFG32(cfgaddr);
+
+	if (size == 1)
+		data = (data & ~(0xff << ((where & 3) << 3))) |
+		    (val << ((where & 3) << 3));
+	else if (size == 2)
+		data = (data & ~(0xffff << ((where & 3) << 3))) |
+		    (val << ((where & 3) << 3));
+	else
+		data = val;
+
+	WRITECFG32(cfgaddr, data);
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+struct pci_ops bcm1480_pci_ops = {
+	.read	= bcm1480_pcibios_read,
+	.write	= bcm1480_pcibios_write,
+};
+
+static struct resource bcm1480_mem_resource = {
+	.name	= "BCM1480 PCI MEM",
+	.start	= A_BCM1480_PHYS_PCI_MEM_MATCH_BYTES,
+	.end	= A_BCM1480_PHYS_PCI_MEM_MATCH_BYTES + 0xfffffffUL,
+	.flags	= IORESOURCE_MEM,
+};
+
+static struct resource bcm1480_io_resource = {
+	.name	= "BCM1480 PCI I/O",
+	.start	= A_BCM1480_PHYS_PCI_IO_MATCH_BYTES,
+	.end	= A_BCM1480_PHYS_PCI_IO_MATCH_BYTES + 0x1ffffffUL,
+	.flags	= IORESOURCE_IO,
+};
+
+struct pci_controller bcm1480_controller = {
+	.pci_ops	= &bcm1480_pci_ops,
+	.mem_resource	= &bcm1480_mem_resource,
+	.io_resource	= &bcm1480_io_resource,
+	.io_offset	= A_BCM1480_PHYS_PCI_IO_MATCH_BYTES,
+};
+
+
+static int __init bcm1480_pcibios_init(void)
+{
+	uint32_t cmdreg;
+	uint64_t reg;
+
+	/* CFE will assign PCI resources */
+	pci_set_flags(PCI_PROBE_ONLY);
+
+	/* Avoid ISA compat ranges.  */
+	PCIBIOS_MIN_IO = 0x00008000UL;
+	PCIBIOS_MIN_MEM = 0x01000000UL;
+
+	/* Set I/O resource limits. - unlimited for now to accommodate HT */
+	ioport_resource.end = 0xffffffffUL;
+	iomem_resource.end = 0xffffffffUL;
+
+	cfg_space = ioremap(A_BCM1480_PHYS_PCI_CFG_MATCH_BITS, 16*1024*1024);
+
+	/*
+	 * See if the PCI bus has been configured by the firmware.
+	 */
+	reg = __raw_readq(IOADDR(A_SCD_SYSTEM_CFG));
+	if (!(reg & M_BCM1480_SYS_PCI_HOST)) {
+		bcm1480_bus_status |= PCI_DEVICE_MODE;
+	} else {
+		cmdreg = READCFG32(CFGOFFSET(0, PCI_DEVFN(PCI_BRIDGE_DEVICE, 0),
+					     PCI_COMMAND));
+		if (!(cmdreg & PCI_COMMAND_MASTER)) {
+			printk
+			    ("PCI: Skipping PCI probe.	Bus is not initialized.\n");
+			iounmap(cfg_space);
+			return 1; /* XXX */
+		}
+		bcm1480_bus_status |= PCI_BUS_ENABLED;
+	}
+
+	/* turn on ExpMemEn */
+	cmdreg = READCFG32(CFGOFFSET(0, PCI_DEVFN(PCI_BRIDGE_DEVICE, 0), 0x40));
+	WRITECFG32(CFGOFFSET(0, PCI_DEVFN(PCI_BRIDGE_DEVICE, 0), 0x40),
+			cmdreg | 0x10);
+	cmdreg = READCFG32(CFGOFFSET(0, PCI_DEVFN(PCI_BRIDGE_DEVICE, 0), 0x40));
+
+	/*
+	 * Establish mappings in KSEG2 (kernel virtual) to PCI I/O
+	 * space.  Use "match bytes" policy to make everything look
+	 * little-endian.  So, you need to also set
+	 * CONFIG_SWAP_IO_SPACE, but this is the combination that
+	 * works correctly with most of Linux's drivers.
+	 * XXX ehs: Should this happen in PCI Device mode?
+	 */
+
+	bcm1480_controller.io_map_base = (unsigned long)
+		ioremap(A_BCM1480_PHYS_PCI_IO_MATCH_BYTES, 65536);
+	bcm1480_controller.io_map_base -= bcm1480_controller.io_offset;
+	set_io_port_base(bcm1480_controller.io_map_base);
+
+	register_pci_controller(&bcm1480_controller);
+
+#ifdef CONFIG_VGA_CONSOLE
+	console_lock();
+	do_take_over_console(&vga_con, 0, MAX_NR_CONSOLES-1, 1);
+	console_unlock();
+#endif
+	return 0;
+}
+
+arch_initcall(bcm1480_pcibios_init);
diff --git a/arch/mips/pci/pci-bcm1480ht.c b/arch/mips/pci/pci-bcm1480ht.c
new file mode 100644
index 000000000..3d996acd2
--- /dev/null
+++ b/arch/mips/pci/pci-bcm1480ht.c
@@ -0,0 +1,203 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2001,2002,2005 Broadcom Corporation
+ * Copyright (C) 2004 by Ralf Baechle (ralf@linux-mips.org)
+ */
+
+/*
+ * BCM1480/1455-specific HT support (looking like PCI)
+ *
+ * This module provides the glue between Linux's PCI subsystem
+ * and the hardware.  We basically provide glue for accessing
+ * configuration space, and set up the translation for I/O
+ * space accesses.
+ *
+ * To access configuration space, we use ioremap.  In the 32-bit
+ * kernel, this consumes either 4 or 8 page table pages, and 16MB of
+ * kernel mapped memory.  Hopefully neither of these should be a huge
+ * problem.
+ *
+ */
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/console.h>
+#include <linux/tty.h>
+
+#include <asm/sibyte/bcm1480_regs.h>
+#include <asm/sibyte/bcm1480_scd.h>
+#include <asm/sibyte/board.h>
+#include <asm/io.h>
+
+/*
+ * Macros for calculating offsets into config space given a device
+ * structure or dev/fun/reg
+ */
+#define CFGOFFSET(bus, devfn, where) (((bus)<<16)+((devfn)<<8)+(where))
+#define CFGADDR(bus, devfn, where)   CFGOFFSET((bus)->number, (devfn), where)
+
+static void *ht_cfg_space;
+
+#define PCI_BUS_ENABLED 1
+#define PCI_DEVICE_MODE 2
+
+static int bcm1480ht_bus_status;
+
+#define PCI_BRIDGE_DEVICE  0
+#define HT_BRIDGE_DEVICE   1
+
+/*
+ * HT's level-sensitive interrupts require EOI, which is generated
+ * through a 4MB memory-mapped region
+ */
+unsigned long ht_eoi_space;
+
+/*
+ * Read/write 32-bit values in config space.
+ */
+static inline u32 READCFG32(u32 addr)
+{
+	return *(u32 *)(ht_cfg_space + (addr&~3));
+}
+
+static inline void WRITECFG32(u32 addr, u32 data)
+{
+	*(u32 *)(ht_cfg_space + (addr & ~3)) = data;
+}
+
+/*
+ * Some checks before doing config cycles:
+ * In PCI Device Mode, hide everything on bus 0 except the LDT host
+ * bridge.  Otherwise, access is controlled by bridge MasterEn bits.
+ */
+static int bcm1480ht_can_access(struct pci_bus *bus, int devfn)
+{
+	u32 devno;
+
+	if (!(bcm1480ht_bus_status & (PCI_BUS_ENABLED | PCI_DEVICE_MODE)))
+		return 0;
+
+	if (bus->number == 0) {
+		devno = PCI_SLOT(devfn);
+		if (bcm1480ht_bus_status & PCI_DEVICE_MODE)
+			return 0;
+	}
+	return 1;
+}
+
+/*
+ * Read/write access functions for various sizes of values
+ * in config space.  Return all 1's for disallowed accesses
+ * for a kludgy but adequate simulation of master aborts.
+ */
+
+static int bcm1480ht_pcibios_read(struct pci_bus *bus, unsigned int devfn,
+				  int where, int size, u32 * val)
+{
+	u32 data = 0;
+
+	if ((size == 2) && (where & 1))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+	else if ((size == 4) && (where & 3))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+
+	if (bcm1480ht_can_access(bus, devfn))
+		data = READCFG32(CFGADDR(bus, devfn, where));
+	else
+		data = 0xFFFFFFFF;
+
+	if (size == 1)
+		*val = (data >> ((where & 3) << 3)) & 0xff;
+	else if (size == 2)
+		*val = (data >> ((where & 3) << 3)) & 0xffff;
+	else
+		*val = data;
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int bcm1480ht_pcibios_write(struct pci_bus *bus, unsigned int devfn,
+				   int where, int size, u32 val)
+{
+	u32 cfgaddr = CFGADDR(bus, devfn, where);
+	u32 data = 0;
+
+	if ((size == 2) && (where & 1))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+	else if ((size == 4) && (where & 3))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+
+	if (!bcm1480ht_can_access(bus, devfn))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+
+	data = READCFG32(cfgaddr);
+
+	if (size == 1)
+		data = (data & ~(0xff << ((where & 3) << 3))) |
+		    (val << ((where & 3) << 3));
+	else if (size == 2)
+		data = (data & ~(0xffff << ((where & 3) << 3))) |
+		    (val << ((where & 3) << 3));
+	else
+		data = val;
+
+	WRITECFG32(cfgaddr, data);
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int bcm1480ht_pcibios_get_busno(void)
+{
+	return 0;
+}
+
+struct pci_ops bcm1480ht_pci_ops = {
+	.read	= bcm1480ht_pcibios_read,
+	.write	= bcm1480ht_pcibios_write,
+};
+
+static struct resource bcm1480ht_mem_resource = {
+	.name	= "BCM1480 HT MEM",
+	.start	= A_BCM1480_PHYS_HT_MEM_MATCH_BYTES,
+	.end	= A_BCM1480_PHYS_HT_MEM_MATCH_BYTES + 0x1fffffffUL,
+	.flags	= IORESOURCE_MEM,
+};
+
+static struct resource bcm1480ht_io_resource = {
+	.name	= "BCM1480 HT I/O",
+	.start	= A_BCM1480_PHYS_HT_IO_MATCH_BYTES,
+	.end	= A_BCM1480_PHYS_HT_IO_MATCH_BYTES + 0x01ffffffUL,
+	.flags	= IORESOURCE_IO,
+};
+
+struct pci_controller bcm1480ht_controller = {
+	.pci_ops	= &bcm1480ht_pci_ops,
+	.mem_resource	= &bcm1480ht_mem_resource,
+	.io_resource	= &bcm1480ht_io_resource,
+	.index		= 1,
+	.get_busno	= bcm1480ht_pcibios_get_busno,
+	.io_offset	= A_BCM1480_PHYS_HT_IO_MATCH_BYTES,
+};
+
+static int __init bcm1480ht_pcibios_init(void)
+{
+	ht_cfg_space = ioremap(A_BCM1480_PHYS_HT_CFG_MATCH_BITS, 16*1024*1024);
+
+	/* CFE doesn't always init all HT paths, so we always scan */
+	bcm1480ht_bus_status |= PCI_BUS_ENABLED;
+
+	ht_eoi_space = (unsigned long)
+		ioremap(A_BCM1480_PHYS_HT_SPECIAL_MATCH_BYTES,
+			4 * 1024 * 1024);
+	bcm1480ht_controller.io_map_base = (unsigned long)
+		ioremap(A_BCM1480_PHYS_HT_IO_MATCH_BYTES, 65536);
+	bcm1480ht_controller.io_map_base -= bcm1480ht_controller.io_offset;
+
+	register_pci_controller(&bcm1480ht_controller);
+
+	return 0;
+}
+
+arch_initcall(bcm1480ht_pcibios_init);
diff --git a/arch/mips/pci/pci-bcm47xx.c b/arch/mips/pci/pci-bcm47xx.c
new file mode 100644
index 000000000..ffac06a5c
--- /dev/null
+++ b/arch/mips/pci/pci-bcm47xx.c
@@ -0,0 +1,98 @@
+/*
+ *  Copyright (C) 2008 Aurelien Jarno <aurelien@aurel32.net>
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/ssb/ssb.h>
+#include <linux/bcma/bcma.h>
+#include <bcm47xx.h>
+
+int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	return 0;
+}
+
+#ifdef CONFIG_BCM47XX_SSB
+static int bcm47xx_pcibios_plat_dev_init_ssb(struct pci_dev *dev)
+{
+	int res;
+	u8 slot, pin;
+
+	res = ssb_pcibios_plat_dev_init(dev);
+	if (res < 0) {
+		pci_alert(dev, "PCI: Failed to init device\n");
+		return res;
+	}
+
+	pci_read_config_byte(dev, PCI_INTERRUPT_PIN, &pin);
+	slot = PCI_SLOT(dev->devfn);
+	res = ssb_pcibios_map_irq(dev, slot, pin);
+
+	/* IRQ-0 and IRQ-1 are software interrupts. */
+	if (res < 2) {
+		pci_alert(dev, "PCI: Failed to map IRQ of device\n");
+		return res;
+	}
+
+	dev->irq = res;
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_BCM47XX_BCMA
+static int bcm47xx_pcibios_plat_dev_init_bcma(struct pci_dev *dev)
+{
+	int res;
+
+	res = bcma_core_pci_plat_dev_init(dev);
+	if (res < 0) {
+		pci_alert(dev, "PCI: Failed to init device\n");
+		return res;
+	}
+
+	res = bcma_core_pci_pcibios_map_irq(dev);
+
+	/* IRQ-0 and IRQ-1 are software interrupts. */
+	if (res < 2) {
+		pci_alert(dev, "PCI: Failed to map IRQ of device\n");
+		return res;
+	}
+
+	dev->irq = res;
+	return 0;
+}
+#endif
+
+int pcibios_plat_dev_init(struct pci_dev *dev)
+{
+#ifdef CONFIG_BCM47XX_SSB
+	if (bcm47xx_bus_type ==	 BCM47XX_BUS_TYPE_SSB)
+		return bcm47xx_pcibios_plat_dev_init_ssb(dev);
+#endif
+#ifdef CONFIG_BCM47XX_BCMA
+	if  (bcm47xx_bus_type ==  BCM47XX_BUS_TYPE_BCMA)
+		return bcm47xx_pcibios_plat_dev_init_bcma(dev);
+#endif
+	return 0;
+}
diff --git a/arch/mips/pci/pci-bcm63xx.c b/arch/mips/pci/pci-bcm63xx.c
new file mode 100644
index 000000000..ac8324377
--- /dev/null
+++ b/arch/mips/pci/pci-bcm63xx.c
@@ -0,0 +1,351 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
+ */
+
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+#include <asm/bootinfo.h>
+
+#include <bcm63xx_reset.h>
+
+#include "pci-bcm63xx.h"
+
+/*
+ * Allow PCI to be disabled at runtime depending on board nvram
+ * configuration
+ */
+int bcm63xx_pci_enabled;
+
+static struct resource bcm_pci_mem_resource = {
+	.name	= "bcm63xx PCI memory space",
+	.start	= BCM_PCI_MEM_BASE_PA,
+	.end	= BCM_PCI_MEM_END_PA,
+	.flags	= IORESOURCE_MEM
+};
+
+static struct resource bcm_pci_io_resource = {
+	.name	= "bcm63xx PCI IO space",
+	.start	= BCM_PCI_IO_BASE_PA,
+#ifdef CONFIG_CARDBUS
+	.end	= BCM_PCI_IO_HALF_PA,
+#else
+	.end	= BCM_PCI_IO_END_PA,
+#endif
+	.flags	= IORESOURCE_IO
+};
+
+struct pci_controller bcm63xx_controller = {
+	.pci_ops	= &bcm63xx_pci_ops,
+	.io_resource	= &bcm_pci_io_resource,
+	.mem_resource	= &bcm_pci_mem_resource,
+};
+
+/*
+ * We handle cardbus  via a fake Cardbus bridge,  memory and io spaces
+ * have to be  clearly separated from PCI one  since we have different
+ * memory decoder.
+ */
+#ifdef CONFIG_CARDBUS
+static struct resource bcm_cb_mem_resource = {
+	.name	= "bcm63xx Cardbus memory space",
+	.start	= BCM_CB_MEM_BASE_PA,
+	.end	= BCM_CB_MEM_END_PA,
+	.flags	= IORESOURCE_MEM
+};
+
+static struct resource bcm_cb_io_resource = {
+	.name	= "bcm63xx Cardbus IO space",
+	.start	= BCM_PCI_IO_HALF_PA + 1,
+	.end	= BCM_PCI_IO_END_PA,
+	.flags	= IORESOURCE_IO
+};
+
+struct pci_controller bcm63xx_cb_controller = {
+	.pci_ops	= &bcm63xx_cb_ops,
+	.io_resource	= &bcm_cb_io_resource,
+	.mem_resource	= &bcm_cb_mem_resource,
+};
+#endif
+
+static struct resource bcm_pcie_mem_resource = {
+	.name	= "bcm63xx PCIe memory space",
+	.start	= BCM_PCIE_MEM_BASE_PA,
+	.end	= BCM_PCIE_MEM_END_PA,
+	.flags	= IORESOURCE_MEM,
+};
+
+static struct resource bcm_pcie_io_resource = {
+	.name	= "bcm63xx PCIe IO space",
+	.start	= 0,
+	.end	= 0,
+	.flags	= 0,
+};
+
+struct pci_controller bcm63xx_pcie_controller = {
+	.pci_ops	= &bcm63xx_pcie_ops,
+	.io_resource	= &bcm_pcie_io_resource,
+	.mem_resource	= &bcm_pcie_mem_resource,
+};
+
+static u32 bcm63xx_int_cfg_readl(u32 reg)
+{
+	u32 tmp;
+
+	tmp = reg & MPI_PCICFGCTL_CFGADDR_MASK;
+	tmp |= MPI_PCICFGCTL_WRITEEN_MASK;
+	bcm_mpi_writel(tmp, MPI_PCICFGCTL_REG);
+	iob();
+	return bcm_mpi_readl(MPI_PCICFGDATA_REG);
+}
+
+static void bcm63xx_int_cfg_writel(u32 val, u32 reg)
+{
+	u32 tmp;
+
+	tmp = reg & MPI_PCICFGCTL_CFGADDR_MASK;
+	tmp |=	MPI_PCICFGCTL_WRITEEN_MASK;
+	bcm_mpi_writel(tmp, MPI_PCICFGCTL_REG);
+	bcm_mpi_writel(val, MPI_PCICFGDATA_REG);
+}
+
+void __iomem *pci_iospace_start;
+
+static void __init bcm63xx_reset_pcie(void)
+{
+	u32 val;
+	u32 reg;
+
+	/* enable SERDES */
+	if (BCMCPU_IS_6328())
+		reg = MISC_SERDES_CTRL_6328_REG;
+	else
+		reg = MISC_SERDES_CTRL_6362_REG;
+
+	val = bcm_misc_readl(reg);
+	val |= SERDES_PCIE_EN | SERDES_PCIE_EXD_EN;
+	bcm_misc_writel(val, reg);
+
+	/* reset the PCIe core */
+	bcm63xx_core_set_reset(BCM63XX_RESET_PCIE, 1);
+	bcm63xx_core_set_reset(BCM63XX_RESET_PCIE_EXT, 1);
+	mdelay(10);
+
+	bcm63xx_core_set_reset(BCM63XX_RESET_PCIE, 0);
+	mdelay(10);
+
+	bcm63xx_core_set_reset(BCM63XX_RESET_PCIE_EXT, 0);
+	mdelay(200);
+}
+
+static struct clk *pcie_clk;
+
+static int __init bcm63xx_register_pcie(void)
+{
+	u32 val;
+
+	/* enable clock */
+	pcie_clk = clk_get(NULL, "pcie");
+	if (IS_ERR_OR_NULL(pcie_clk))
+		return -ENODEV;
+
+	clk_prepare_enable(pcie_clk);
+
+	bcm63xx_reset_pcie();
+
+	/* configure the PCIe bridge */
+	val = bcm_pcie_readl(PCIE_BRIDGE_OPT1_REG);
+	val |= OPT1_RD_BE_OPT_EN;
+	val |= OPT1_RD_REPLY_BE_FIX_EN;
+	val |= OPT1_PCIE_BRIDGE_HOLE_DET_EN;
+	val |= OPT1_L1_INT_STATUS_MASK_POL;
+	bcm_pcie_writel(val, PCIE_BRIDGE_OPT1_REG);
+
+	/* setup the interrupts */
+	val = bcm_pcie_readl(PCIE_BRIDGE_RC_INT_MASK_REG);
+	val |= PCIE_RC_INT_A | PCIE_RC_INT_B | PCIE_RC_INT_C | PCIE_RC_INT_D;
+	bcm_pcie_writel(val, PCIE_BRIDGE_RC_INT_MASK_REG);
+
+	val = bcm_pcie_readl(PCIE_BRIDGE_OPT2_REG);
+	/* enable credit checking and error checking */
+	val |= OPT2_TX_CREDIT_CHK_EN;
+	val |= OPT2_UBUS_UR_DECODE_DIS;
+
+	/* set device bus/func for the pcie device */
+	val |= (PCIE_BUS_DEVICE << OPT2_CFG_TYPE1_BUS_NO_SHIFT);
+	val |= OPT2_CFG_TYPE1_BD_SEL;
+	bcm_pcie_writel(val, PCIE_BRIDGE_OPT2_REG);
+
+	/* setup class code as bridge */
+	val = bcm_pcie_readl(PCIE_IDVAL3_REG);
+	val &= ~IDVAL3_CLASS_CODE_MASK;
+	val |= PCI_CLASS_BRIDGE_PCI_NORMAL;
+	bcm_pcie_writel(val, PCIE_IDVAL3_REG);
+
+	/* disable bar1 size */
+	val = bcm_pcie_readl(PCIE_CONFIG2_REG);
+	val &= ~CONFIG2_BAR1_SIZE_MASK;
+	bcm_pcie_writel(val, PCIE_CONFIG2_REG);
+
+	/* set bar0 to little endian */
+	val = (BCM_PCIE_MEM_BASE_PA >> 20) << BASEMASK_BASE_SHIFT;
+	val |= (BCM_PCIE_MEM_BASE_PA >> 20) << BASEMASK_MASK_SHIFT;
+	val |= BASEMASK_REMAP_EN;
+	bcm_pcie_writel(val, PCIE_BRIDGE_BAR0_BASEMASK_REG);
+
+	val = (BCM_PCIE_MEM_BASE_PA >> 20) << REBASE_ADDR_BASE_SHIFT;
+	bcm_pcie_writel(val, PCIE_BRIDGE_BAR0_REBASE_ADDR_REG);
+
+	register_pci_controller(&bcm63xx_pcie_controller);
+
+	return 0;
+}
+
+static int __init bcm63xx_register_pci(void)
+{
+	unsigned int mem_size;
+	u32 val;
+	/*
+	 * configuration  access are  done through  IO space,  remap 4
+	 * first bytes to access it from CPU.
+	 *
+	 * this means that  no io access from CPU  should happen while
+	 * we do a configuration cycle,	 but there's no way we can add
+	 * a spinlock for each io access, so this is currently kind of
+	 * broken on SMP.
+	 */
+	pci_iospace_start = ioremap(BCM_PCI_IO_BASE_PA, 4);
+	if (!pci_iospace_start)
+		return -ENOMEM;
+
+	/* setup local bus to PCI access (PCI memory) */
+	val = BCM_PCI_MEM_BASE_PA & MPI_L2P_BASE_MASK;
+	bcm_mpi_writel(val, MPI_L2PMEMBASE1_REG);
+	bcm_mpi_writel(~(BCM_PCI_MEM_SIZE - 1), MPI_L2PMEMRANGE1_REG);
+	bcm_mpi_writel(val | MPI_L2PREMAP_ENABLED_MASK, MPI_L2PMEMREMAP1_REG);
+
+	/* set Cardbus IDSEL (type 0 cfg access on primary bus for
+	 * this IDSEL will be done on Cardbus instead) */
+	val = bcm_pcmcia_readl(PCMCIA_C1_REG);
+	val &= ~PCMCIA_C1_CBIDSEL_MASK;
+	val |= (CARDBUS_PCI_IDSEL << PCMCIA_C1_CBIDSEL_SHIFT);
+	bcm_pcmcia_writel(val, PCMCIA_C1_REG);
+
+#ifdef CONFIG_CARDBUS
+	/* setup local bus to PCI access (Cardbus memory) */
+	val = BCM_CB_MEM_BASE_PA & MPI_L2P_BASE_MASK;
+	bcm_mpi_writel(val, MPI_L2PMEMBASE2_REG);
+	bcm_mpi_writel(~(BCM_CB_MEM_SIZE - 1), MPI_L2PMEMRANGE2_REG);
+	val |= MPI_L2PREMAP_ENABLED_MASK | MPI_L2PREMAP_IS_CARDBUS_MASK;
+	bcm_mpi_writel(val, MPI_L2PMEMREMAP2_REG);
+#else
+	/* disable second access windows */
+	bcm_mpi_writel(0, MPI_L2PMEMREMAP2_REG);
+#endif
+
+	/* setup local bus  to PCI access (IO memory),	we have only 1
+	 * IO window  for both PCI  and cardbus, but it	 cannot handle
+	 * both	 at the	 same time,  assume standard  PCI for  now, if
+	 * cardbus card has  IO zone, PCI fixup will  change window to
+	 * cardbus */
+	val = BCM_PCI_IO_BASE_PA & MPI_L2P_BASE_MASK;
+	bcm_mpi_writel(val, MPI_L2PIOBASE_REG);
+	bcm_mpi_writel(~(BCM_PCI_IO_SIZE - 1), MPI_L2PIORANGE_REG);
+	bcm_mpi_writel(val | MPI_L2PREMAP_ENABLED_MASK, MPI_L2PIOREMAP_REG);
+
+	/* enable PCI related GPIO pins */
+	bcm_mpi_writel(MPI_LOCBUSCTL_EN_PCI_GPIO_MASK, MPI_LOCBUSCTL_REG);
+
+	/* setup PCI to local bus access, used by PCI device to target
+	 * local RAM while bus mastering */
+	bcm63xx_int_cfg_writel(0, PCI_BASE_ADDRESS_3);
+	if (BCMCPU_IS_3368() || BCMCPU_IS_6358() || BCMCPU_IS_6368())
+		val = MPI_SP0_REMAP_ENABLE_MASK;
+	else
+		val = 0;
+	bcm_mpi_writel(val, MPI_SP0_REMAP_REG);
+
+	bcm63xx_int_cfg_writel(0x0, PCI_BASE_ADDRESS_4);
+	bcm_mpi_writel(0, MPI_SP1_REMAP_REG);
+
+	mem_size = bcm63xx_get_memory_size();
+
+	/* 6348 before rev b0 exposes only 16 MB of RAM memory through
+	 * PCI, throw a warning if we have more memory */
+	if (BCMCPU_IS_6348() && (bcm63xx_get_cpu_rev() & 0xf0) == 0xa0) {
+		if (mem_size > (16 * 1024 * 1024))
+			printk(KERN_WARNING "bcm63xx: this CPU "
+			       "revision cannot handle more than 16MB "
+			       "of RAM for PCI bus mastering\n");
+	} else {
+		/* setup sp0 range to local RAM size */
+		bcm_mpi_writel(~(mem_size - 1), MPI_SP0_RANGE_REG);
+		bcm_mpi_writel(0, MPI_SP1_RANGE_REG);
+	}
+
+	/* change  host bridge	retry  counter to  infinite number  of
+	 * retry,  needed for  some broadcom  wifi cards  with Silicon
+	 * Backplane bus where access to srom seems very slow  */
+	val = bcm63xx_int_cfg_readl(BCMPCI_REG_TIMERS);
+	val &= ~REG_TIMER_RETRY_MASK;
+	bcm63xx_int_cfg_writel(val, BCMPCI_REG_TIMERS);
+
+	/* enable memory decoder and bus mastering */
+	val = bcm63xx_int_cfg_readl(PCI_COMMAND);
+	val |= (PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
+	bcm63xx_int_cfg_writel(val, PCI_COMMAND);
+
+	/* enable read prefetching & disable byte swapping for bus
+	 * mastering transfers */
+	val = bcm_mpi_readl(MPI_PCIMODESEL_REG);
+	val &= ~MPI_PCIMODESEL_BAR1_NOSWAP_MASK;
+	val &= ~MPI_PCIMODESEL_BAR2_NOSWAP_MASK;
+	val &= ~MPI_PCIMODESEL_PREFETCH_MASK;
+	val |= (8 << MPI_PCIMODESEL_PREFETCH_SHIFT);
+	bcm_mpi_writel(val, MPI_PCIMODESEL_REG);
+
+	/* enable pci interrupt */
+	val = bcm_mpi_readl(MPI_LOCINT_REG);
+	val |= MPI_LOCINT_MASK(MPI_LOCINT_EXT_PCI_INT);
+	bcm_mpi_writel(val, MPI_LOCINT_REG);
+
+	register_pci_controller(&bcm63xx_controller);
+
+#ifdef CONFIG_CARDBUS
+	register_pci_controller(&bcm63xx_cb_controller);
+#endif
+
+	/* mark memory space used for IO mapping as reserved */
+	request_mem_region(BCM_PCI_IO_BASE_PA, BCM_PCI_IO_SIZE,
+			   "bcm63xx PCI IO space");
+	return 0;
+}
+
+
+static int __init bcm63xx_pci_init(void)
+{
+	if (!bcm63xx_pci_enabled)
+		return -ENODEV;
+
+	switch (bcm63xx_get_cpu_id()) {
+	case BCM6328_CPU_ID:
+	case BCM6362_CPU_ID:
+		return bcm63xx_register_pcie();
+	case BCM3368_CPU_ID:
+	case BCM6348_CPU_ID:
+	case BCM6358_CPU_ID:
+	case BCM6368_CPU_ID:
+		return bcm63xx_register_pci();
+	default:
+		return -ENODEV;
+	}
+}
+
+arch_initcall(bcm63xx_pci_init);
diff --git a/arch/mips/pci/pci-bcm63xx.h b/arch/mips/pci/pci-bcm63xx.h
new file mode 100644
index 000000000..214def1e4
--- /dev/null
+++ b/arch/mips/pci/pci-bcm63xx.h
@@ -0,0 +1,33 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef PCI_BCM63XX_H_
+#define PCI_BCM63XX_H_
+
+#include <bcm63xx_cpu.h>
+#include <bcm63xx_io.h>
+#include <bcm63xx_regs.h>
+#include <bcm63xx_dev_pci.h>
+
+/*
+ * Cardbus shares  the PCI bus, but has	 no IDSEL, so a	 special id is
+ * reserved for it.  If you have a standard PCI device at this id, you
+ * need to change the following definition.
+ */
+#define CARDBUS_PCI_IDSEL	0x8
+
+
+#define PCIE_BUS_BRIDGE		0
+#define PCIE_BUS_DEVICE		1
+
+/*
+ * defined in ops-bcm63xx.c
+ */
+extern struct pci_ops bcm63xx_pci_ops;
+extern struct pci_ops bcm63xx_cb_ops;
+extern struct pci_ops bcm63xx_pcie_ops;
+
+/*
+ * defined in pci-bcm63xx.c
+ */
+extern void __iomem *pci_iospace_start;
+
+#endif /* ! PCI_BCM63XX_H_ */
diff --git a/arch/mips/pci/pci-generic.c b/arch/mips/pci/pci-generic.c
new file mode 100644
index 000000000..d2d68bac3
--- /dev/null
+++ b/arch/mips/pci/pci-generic.c
@@ -0,0 +1,64 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2016 Imagination Technologies
+ * Author: Paul Burton <paul.burton@mips.com>
+ *
+ * pcibios_align_resource taken from arch/arm/kernel/bios32.c.
+ */
+
+#include <linux/pci.h>
+
+/*
+ * We need to avoid collisions with `mirrored' VGA ports
+ * and other strange ISA hardware, so we always want the
+ * addresses to be allocated in the 0x000-0x0ff region
+ * modulo 0x400.
+ *
+ * Why? Because some silly external IO cards only decode
+ * the low 10 bits of the IO address. The 0x00-0xff region
+ * is reserved for motherboard devices that decode all 16
+ * bits, so it's ok to allocate at, say, 0x2800-0x28ff,
+ * but we want to try to avoid allocating at 0x2900-0x2bff
+ * which might have be mirrored at 0x0100-0x03ff..
+ */
+resource_size_t pcibios_align_resource(void *data, const struct resource *res,
+				resource_size_t size, resource_size_t align)
+{
+	struct pci_dev *dev = data;
+	resource_size_t start = res->start;
+	struct pci_host_bridge *host_bridge;
+
+	if (res->flags & IORESOURCE_IO && start & 0x300)
+		start = (start + 0x3ff) & ~0x3ff;
+
+	start = (start + align - 1) & ~(align - 1);
+
+	host_bridge = pci_find_host_bridge(dev->bus);
+
+	if (host_bridge->align_resource)
+		return host_bridge->align_resource(dev, res,
+				start, size, align);
+
+	return start;
+}
+
+void pcibios_fixup_bus(struct pci_bus *bus)
+{
+	pci_read_bridge_bases(bus);
+}
+
+#ifdef pci_remap_iospace
+int pci_remap_iospace(const struct resource *res, phys_addr_t phys_addr)
+{
+	unsigned long vaddr;
+
+	if (res->start != 0) {
+		WARN_ONCE(1, "resource start address is not zero\n");
+		return -ENODEV;
+	}
+
+	vaddr = (unsigned long)ioremap(phys_addr, resource_size(res));
+	set_io_port_base(vaddr);
+	return 0;
+}
+#endif
diff --git a/arch/mips/pci/pci-ip27.c b/arch/mips/pci/pci-ip27.c
new file mode 100644
index 000000000..d85cbf84e
--- /dev/null
+++ b/arch/mips/pci/pci-ip27.c
@@ -0,0 +1,42 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003 Christoph Hellwig (hch@lst.de)
+ * Copyright (C) 1999, 2000, 04 Ralf Baechle (ralf@linux-mips.org)
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ */
+#include <asm/sn/addrs.h>
+#include <asm/sn/types.h>
+#include <asm/sn/klconfig.h>
+#include <asm/sn/agent.h>
+#include <asm/sn/ioc3.h>
+#include <asm/pci/bridge.h>
+
+#ifdef CONFIG_NUMA
+int pcibus_to_node(struct pci_bus *bus)
+{
+	struct bridge_controller *bc = BRIDGE_CONTROLLER(bus);
+
+	return bc->nasid;
+}
+EXPORT_SYMBOL(pcibus_to_node);
+#endif /* CONFIG_NUMA */
+
+static void ip29_fixup_phy(struct pci_dev *dev)
+{
+	int nasid = pcibus_to_node(dev->bus);
+	u32 sid;
+
+	if (nasid != 1)
+		return; /* only needed on second module */
+
+	/* enable ethernet PHY on IP29 systemboard */
+	pci_read_config_dword(dev, PCI_SUBSYSTEM_VENDOR_ID, &sid);
+	if (sid == (PCI_VENDOR_ID_SGI | (IOC3_SUBSYS_IP29_SYSBOARD) << 16))
+		REMOTE_HUB_S(nasid, MD_LED0, 0x09);
+}
+
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SGI, PCI_DEVICE_ID_SGI_IOC3,
+			ip29_fixup_phy);
diff --git a/arch/mips/pci/pci-ip32.c b/arch/mips/pci/pci-ip32.c
new file mode 100644
index 000000000..7ae89d0c7
--- /dev/null
+++ b/arch/mips/pci/pci-ip32.c
@@ -0,0 +1,147 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2000, 2001 Keith M Wesolowski
+ * Copyright (C) 2004 by Ralf Baechle (ralf@linux-mips.org)
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/pci.h>
+#include <linux/types.h>
+#include <asm/ip32/mace.h>
+#include <asm/ip32/ip32_ints.h>
+
+#undef DEBUG_MACE_PCI
+
+/*
+ * Handle errors from the bridge.  This includes master and target aborts,
+ * various command and address errors, and the interrupt test.	This gets
+ * registered on the bridge error irq.	It's conceivable that some of these
+ * conditions warrant a panic.	Anybody care to say which ones?
+ */
+static irqreturn_t macepci_error(int irq, void *dev)
+{
+	char s;
+	unsigned int flags = mace->pci.error;
+	unsigned int addr = mace->pci.error_addr;
+
+	if (flags & MACEPCI_ERROR_MEMORY_ADDR)
+		s = 'M';
+	else if (flags & MACEPCI_ERROR_CONFIG_ADDR)
+		s = 'C';
+	else
+		s = 'X';
+
+	if (flags & MACEPCI_ERROR_MASTER_ABORT) {
+		printk("MACEPCI: Master abort at 0x%08x (%c)\n", addr, s);
+		flags &= ~MACEPCI_ERROR_MASTER_ABORT;
+	}
+	if (flags & MACEPCI_ERROR_TARGET_ABORT) {
+		printk("MACEPCI: Target abort at 0x%08x (%c)\n", addr, s);
+		flags &= ~MACEPCI_ERROR_TARGET_ABORT;
+	}
+	if (flags & MACEPCI_ERROR_DATA_PARITY_ERR) {
+		printk("MACEPCI: Data parity error at 0x%08x (%c)\n", addr, s);
+		flags &= ~MACEPCI_ERROR_DATA_PARITY_ERR;
+	}
+	if (flags & MACEPCI_ERROR_RETRY_ERR) {
+		printk("MACEPCI: Retry error at 0x%08x (%c)\n", addr, s);
+		flags &= ~MACEPCI_ERROR_RETRY_ERR;
+	}
+	if (flags & MACEPCI_ERROR_ILLEGAL_CMD) {
+		printk("MACEPCI: Illegal command at 0x%08x (%c)\n", addr, s);
+		flags &= ~MACEPCI_ERROR_ILLEGAL_CMD;
+	}
+	if (flags & MACEPCI_ERROR_SYSTEM_ERR) {
+		printk("MACEPCI: System error at 0x%08x (%c)\n", addr, s);
+		flags &= ~MACEPCI_ERROR_SYSTEM_ERR;
+	}
+	if (flags & MACEPCI_ERROR_PARITY_ERR) {
+		printk("MACEPCI: Parity error at 0x%08x (%c)\n", addr, s);
+		flags &= ~MACEPCI_ERROR_PARITY_ERR;
+	}
+	if (flags & MACEPCI_ERROR_OVERRUN) {
+		printk("MACEPCI: Overrun error at 0x%08x (%c)\n", addr, s);
+		flags &= ~MACEPCI_ERROR_OVERRUN;
+	}
+	if (flags & MACEPCI_ERROR_SIG_TABORT) {
+		printk("MACEPCI: Signaled target abort (clearing)\n");
+		flags &= ~MACEPCI_ERROR_SIG_TABORT;
+	}
+	if (flags & MACEPCI_ERROR_INTERRUPT_TEST) {
+		printk("MACEPCI: Interrupt test triggered (clearing)\n");
+		flags &= ~MACEPCI_ERROR_INTERRUPT_TEST;
+	}
+
+	mace->pci.error = flags;
+
+	return IRQ_HANDLED;
+}
+
+
+extern struct pci_ops mace_pci_ops;
+#ifdef CONFIG_64BIT
+static struct resource mace_pci_mem_resource = {
+	.name	= "SGI O2 PCI MEM",
+	.start	= MACEPCI_HI_MEMORY,
+	.end	= 0x2FFFFFFFFUL,
+	.flags	= IORESOURCE_MEM,
+};
+static struct resource mace_pci_io_resource = {
+	.name	= "SGI O2 PCI IO",
+	.start	= 0x00000000UL,
+	.end	= 0xffffffffUL,
+	.flags	= IORESOURCE_IO,
+};
+#define MACE_PCI_MEM_OFFSET 0x200000000
+#else
+static struct resource mace_pci_mem_resource = {
+	.name	= "SGI O2 PCI MEM",
+	.start	= MACEPCI_LOW_MEMORY,
+	.end	= MACEPCI_LOW_MEMORY + 0x2000000 - 1,
+	.flags	= IORESOURCE_MEM,
+};
+static struct resource mace_pci_io_resource = {
+	.name	= "SGI O2 PCI IO",
+	.start	= 0x00000000,
+	.end	= 0xFFFFFFFF,
+	.flags	= IORESOURCE_IO,
+};
+#define MACE_PCI_MEM_OFFSET (MACEPCI_LOW_MEMORY - 0x80000000)
+#endif
+static struct pci_controller mace_pci_controller = {
+	.pci_ops	= &mace_pci_ops,
+	.mem_resource	= &mace_pci_mem_resource,
+	.io_resource	= &mace_pci_io_resource,
+	.mem_offset	= MACE_PCI_MEM_OFFSET,
+	.io_offset	= 0,
+	.io_map_base	= CKSEG1ADDR(MACEPCI_LOW_IO),
+};
+
+static int __init mace_init(void)
+{
+	PCIBIOS_MIN_IO = 0x1000;
+
+	/* Clear any outstanding errors and enable interrupts */
+	mace->pci.error_addr = 0;
+	mace->pci.error = 0;
+	mace->pci.control = 0xff008500;
+
+	printk("MACE PCI rev %d\n", mace->pci.rev);
+
+	BUG_ON(request_irq(MACE_PCI_BRIDGE_IRQ, macepci_error, 0,
+			   "MACE PCI error", NULL));
+
+	/* extend memory resources */
+	iomem_resource.end = mace_pci_mem_resource.end;
+	ioport_resource = mace_pci_io_resource;
+
+	register_pci_controller(&mace_pci_controller);
+
+	return 0;
+}
+
+arch_initcall(mace_init);
diff --git a/arch/mips/pci/pci-lantiq.c b/arch/mips/pci/pci-lantiq.c
new file mode 100644
index 000000000..8d16cd021
--- /dev/null
+++ b/arch/mips/pci/pci-lantiq.c
@@ -0,0 +1,249 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ *  Copyright (C) 2010 John Crispin <john@phrozen.org>
+ */
+
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/mm.h>
+#include <linux/vmalloc.h>
+#include <linux/clk.h>
+#include <linux/of_platform.h>
+#include <linux/of_irq.h>
+#include <linux/of_pci.h>
+
+#include <asm/addrspace.h>
+
+#include <lantiq_soc.h>
+#include <lantiq_irq.h>
+
+#include "pci-lantiq.h"
+
+#define PCI_CR_FCI_ADDR_MAP0		0x00C0
+#define PCI_CR_FCI_ADDR_MAP1		0x00C4
+#define PCI_CR_FCI_ADDR_MAP2		0x00C8
+#define PCI_CR_FCI_ADDR_MAP3		0x00CC
+#define PCI_CR_FCI_ADDR_MAP4		0x00D0
+#define PCI_CR_FCI_ADDR_MAP5		0x00D4
+#define PCI_CR_FCI_ADDR_MAP6		0x00D8
+#define PCI_CR_FCI_ADDR_MAP7		0x00DC
+#define PCI_CR_CLK_CTRL			0x0000
+#define PCI_CR_PCI_MOD			0x0030
+#define PCI_CR_PC_ARB			0x0080
+#define PCI_CR_FCI_ADDR_MAP11hg		0x00E4
+#define PCI_CR_BAR11MASK		0x0044
+#define PCI_CR_BAR12MASK		0x0048
+#define PCI_CR_BAR13MASK		0x004C
+#define PCI_CS_BASE_ADDR1		0x0010
+#define PCI_CR_PCI_ADDR_MAP11		0x0064
+#define PCI_CR_FCI_BURST_LENGTH		0x00E8
+#define PCI_CR_PCI_EOI			0x002C
+#define PCI_CS_STS_CMD			0x0004
+
+#define PCI_MASTER0_REQ_MASK_2BITS	8
+#define PCI_MASTER1_REQ_MASK_2BITS	10
+#define PCI_MASTER2_REQ_MASK_2BITS	12
+#define INTERNAL_ARB_ENABLE_BIT		0
+
+#define LTQ_CGU_IFCCR		0x0018
+#define LTQ_CGU_PCICR		0x0034
+
+#define ltq_pci_w32(x, y)	ltq_w32((x), ltq_pci_membase + (y))
+#define ltq_pci_r32(x)		ltq_r32(ltq_pci_membase + (x))
+
+#define ltq_pci_cfg_w32(x, y)	ltq_w32((x), ltq_pci_mapped_cfg + (y))
+#define ltq_pci_cfg_r32(x)	ltq_r32(ltq_pci_mapped_cfg + (x))
+
+__iomem void *ltq_pci_mapped_cfg;
+static __iomem void *ltq_pci_membase;
+
+static struct gpio_desc *reset_gpio;
+static struct clk *clk_pci, *clk_external;
+static struct resource pci_io_resource;
+static struct resource pci_mem_resource;
+static struct pci_ops pci_ops = {
+	.read	= ltq_pci_read_config_dword,
+	.write	= ltq_pci_write_config_dword
+};
+
+static struct pci_controller pci_controller = {
+	.pci_ops	= &pci_ops,
+	.mem_resource	= &pci_mem_resource,
+	.mem_offset	= 0x00000000UL,
+	.io_resource	= &pci_io_resource,
+	.io_offset	= 0x00000000UL,
+};
+
+static inline u32 ltq_calc_bar11mask(void)
+{
+	u32 mem, bar11mask;
+
+	/* BAR11MASK value depends on available memory on system. */
+	mem = get_num_physpages() * PAGE_SIZE;
+	bar11mask = (0x0ffffff0 & ~((1 << (fls(mem) - 1)) - 1)) | 8;
+
+	return bar11mask;
+}
+
+static int ltq_pci_startup(struct platform_device *pdev)
+{
+	struct device_node *node = pdev->dev.of_node;
+	const __be32 *req_mask, *bus_clk;
+	u32 temp_buffer;
+	int error;
+
+	/* get our clocks */
+	clk_pci = clk_get(&pdev->dev, NULL);
+	if (IS_ERR(clk_pci)) {
+		dev_err(&pdev->dev, "failed to get pci clock\n");
+		return PTR_ERR(clk_pci);
+	}
+
+	clk_external = clk_get(&pdev->dev, "external");
+	if (IS_ERR(clk_external)) {
+		clk_put(clk_pci);
+		dev_err(&pdev->dev, "failed to get external pci clock\n");
+		return PTR_ERR(clk_external);
+	}
+
+	/* read the bus speed that we want */
+	bus_clk = of_get_property(node, "lantiq,bus-clock", NULL);
+	if (bus_clk)
+		clk_set_rate(clk_pci, *bus_clk);
+
+	/* and enable the clocks */
+	clk_enable(clk_pci);
+	if (of_find_property(node, "lantiq,external-clock", NULL))
+		clk_enable(clk_external);
+	else
+		clk_disable(clk_external);
+
+	/* setup reset gpio used by pci */
+	reset_gpio = devm_gpiod_get_optional(&pdev->dev, "reset",
+					     GPIOD_OUT_LOW);
+	error = PTR_ERR_OR_ZERO(reset_gpio);
+	if (error) {
+		dev_err(&pdev->dev, "failed to request gpio: %d\n", error);
+		return error;
+	}
+	gpiod_set_consumer_name(reset_gpio, "pci_reset");
+
+	/* enable auto-switching between PCI and EBU */
+	ltq_pci_w32(0xa, PCI_CR_CLK_CTRL);
+
+	/* busy, i.e. configuration is not done, PCI access has to be retried */
+	ltq_pci_w32(ltq_pci_r32(PCI_CR_PCI_MOD) & ~(1 << 24), PCI_CR_PCI_MOD);
+	wmb();
+	/* BUS Master/IO/MEM access */
+	ltq_pci_cfg_w32(ltq_pci_cfg_r32(PCI_CS_STS_CMD) | 7, PCI_CS_STS_CMD);
+
+	/* enable external 2 PCI masters */
+	temp_buffer = ltq_pci_r32(PCI_CR_PC_ARB);
+	/* setup the request mask */
+	req_mask = of_get_property(node, "req-mask", NULL);
+	if (req_mask)
+		temp_buffer &= ~((*req_mask & 0xf) << 16);
+	else
+		temp_buffer &= ~0xf0000;
+	/* enable internal arbiter */
+	temp_buffer |= (1 << INTERNAL_ARB_ENABLE_BIT);
+	/* enable internal PCI master reqest */
+	temp_buffer &= (~(3 << PCI_MASTER0_REQ_MASK_2BITS));
+
+	/* enable EBU request */
+	temp_buffer &= (~(3 << PCI_MASTER1_REQ_MASK_2BITS));
+
+	/* enable all external masters request */
+	temp_buffer &= (~(3 << PCI_MASTER2_REQ_MASK_2BITS));
+	ltq_pci_w32(temp_buffer, PCI_CR_PC_ARB);
+	wmb();
+
+	/* setup BAR memory regions */
+	ltq_pci_w32(0x18000000, PCI_CR_FCI_ADDR_MAP0);
+	ltq_pci_w32(0x18400000, PCI_CR_FCI_ADDR_MAP1);
+	ltq_pci_w32(0x18800000, PCI_CR_FCI_ADDR_MAP2);
+	ltq_pci_w32(0x18c00000, PCI_CR_FCI_ADDR_MAP3);
+	ltq_pci_w32(0x19000000, PCI_CR_FCI_ADDR_MAP4);
+	ltq_pci_w32(0x19400000, PCI_CR_FCI_ADDR_MAP5);
+	ltq_pci_w32(0x19800000, PCI_CR_FCI_ADDR_MAP6);
+	ltq_pci_w32(0x19c00000, PCI_CR_FCI_ADDR_MAP7);
+	ltq_pci_w32(0x1ae00000, PCI_CR_FCI_ADDR_MAP11hg);
+	ltq_pci_w32(ltq_calc_bar11mask(), PCI_CR_BAR11MASK);
+	ltq_pci_w32(0, PCI_CR_PCI_ADDR_MAP11);
+	ltq_pci_w32(0, PCI_CS_BASE_ADDR1);
+	/* both TX and RX endian swap are enabled */
+	ltq_pci_w32(ltq_pci_r32(PCI_CR_PCI_EOI) | 3, PCI_CR_PCI_EOI);
+	wmb();
+	ltq_pci_w32(ltq_pci_r32(PCI_CR_BAR12MASK) | 0x80000000,
+		PCI_CR_BAR12MASK);
+	ltq_pci_w32(ltq_pci_r32(PCI_CR_BAR13MASK) | 0x80000000,
+		PCI_CR_BAR13MASK);
+	/*use 8 dw burst length */
+	ltq_pci_w32(0x303, PCI_CR_FCI_BURST_LENGTH);
+	ltq_pci_w32(ltq_pci_r32(PCI_CR_PCI_MOD) | (1 << 24), PCI_CR_PCI_MOD);
+	wmb();
+
+	/* setup irq line */
+	ltq_ebu_w32(ltq_ebu_r32(LTQ_EBU_PCC_CON) | 0xc, LTQ_EBU_PCC_CON);
+	ltq_ebu_w32(ltq_ebu_r32(LTQ_EBU_PCC_IEN) | 0x10, LTQ_EBU_PCC_IEN);
+
+	/* toggle reset pin */
+	if (reset_gpio) {
+		gpiod_set_value_cansleep(reset_gpio, 1);
+		wmb();
+		mdelay(1);
+		gpiod_set_value_cansleep(reset_gpio, 0);
+	}
+	return 0;
+}
+
+static int ltq_pci_probe(struct platform_device *pdev)
+{
+	struct resource *res_cfg, *res_bridge;
+
+	pci_clear_flags(PCI_PROBE_ONLY);
+
+	res_bridge = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+	ltq_pci_membase = devm_ioremap_resource(&pdev->dev, res_bridge);
+	if (IS_ERR(ltq_pci_membase))
+		return PTR_ERR(ltq_pci_membase);
+
+	res_cfg = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	ltq_pci_mapped_cfg = devm_ioremap_resource(&pdev->dev, res_cfg);
+	if (IS_ERR(ltq_pci_mapped_cfg))
+		return PTR_ERR(ltq_pci_mapped_cfg);
+
+	ltq_pci_startup(pdev);
+
+	pci_load_of_ranges(&pci_controller, pdev->dev.of_node);
+	register_pci_controller(&pci_controller);
+	return 0;
+}
+
+static const struct of_device_id ltq_pci_match[] = {
+	{ .compatible = "lantiq,pci-xway" },
+	{},
+};
+
+static struct platform_driver ltq_pci_driver = {
+	.probe = ltq_pci_probe,
+	.driver = {
+		.name = "pci-xway",
+		.of_match_table = ltq_pci_match,
+	},
+};
+
+int __init pcibios_init(void)
+{
+	int ret = platform_driver_register(&ltq_pci_driver);
+	if (ret)
+		pr_info("pci-xway: Error registering platform driver!");
+	return ret;
+}
+
+arch_initcall(pcibios_init);
diff --git a/arch/mips/pci/pci-lantiq.h b/arch/mips/pci/pci-lantiq.h
new file mode 100644
index 000000000..fdbb0e89b
--- /dev/null
+++ b/arch/mips/pci/pci-lantiq.h
@@ -0,0 +1,16 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *
+ *  Copyright (C) 2010 John Crispin <john@phrozen.org>
+ */
+
+#ifndef _LTQ_PCI_H__
+#define _LTQ_PCI_H__
+
+extern __iomem void *ltq_pci_mapped_cfg;
+extern int ltq_pci_read_config_dword(struct pci_bus *bus,
+	unsigned int devfn, int where, int size, u32 *val);
+extern int ltq_pci_write_config_dword(struct pci_bus *bus,
+	unsigned int devfn, int where, int size, u32 val);
+
+#endif
diff --git a/arch/mips/pci/pci-legacy.c b/arch/mips/pci/pci-legacy.c
new file mode 100644
index 000000000..468722c8a
--- /dev/null
+++ b/arch/mips/pci/pci-legacy.c
@@ -0,0 +1,307 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *
+ * Copyright (C) 2003, 04, 11 Ralf Baechle (ralf@linux-mips.org)
+ * Copyright (C) 2011 Wind River Systems,
+ *   written by Ralf Baechle (ralf@linux-mips.org)
+ */
+#include <linux/bug.h>
+#include <linux/kernel.h>
+#include <linux/mm.h>
+#include <linux/memblock.h>
+#include <linux/export.h>
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/of_address.h>
+
+#include <asm/cpu-info.h>
+
+/*
+ * If PCI_PROBE_ONLY in pci_flags is set, we don't change any PCI resource
+ * assignments.
+ */
+
+/*
+ * The PCI controller list.
+ */
+static LIST_HEAD(controllers);
+
+static int pci_initialized;
+
+/*
+ * We need to avoid collisions with `mirrored' VGA ports
+ * and other strange ISA hardware, so we always want the
+ * addresses to be allocated in the 0x000-0x0ff region
+ * modulo 0x400.
+ *
+ * Why? Because some silly external IO cards only decode
+ * the low 10 bits of the IO address. The 0x00-0xff region
+ * is reserved for motherboard devices that decode all 16
+ * bits, so it's ok to allocate at, say, 0x2800-0x28ff,
+ * but we want to try to avoid allocating at 0x2900-0x2bff
+ * which might have be mirrored at 0x0100-0x03ff..
+ */
+resource_size_t
+pcibios_align_resource(void *data, const struct resource *res,
+		       resource_size_t size, resource_size_t align)
+{
+	struct pci_dev *dev = data;
+	struct pci_controller *hose = dev->sysdata;
+	resource_size_t start = res->start;
+
+	if (res->flags & IORESOURCE_IO) {
+		/* Make sure we start at our min on all hoses */
+		if (start < PCIBIOS_MIN_IO + hose->io_resource->start)
+			start = PCIBIOS_MIN_IO + hose->io_resource->start;
+
+		/*
+		 * Put everything into 0x00-0xff region modulo 0x400
+		 */
+		if (start & 0x300)
+			start = (start + 0x3ff) & ~0x3ff;
+	} else if (res->flags & IORESOURCE_MEM) {
+		/* Make sure we start at our min on all hoses */
+		if (start < PCIBIOS_MIN_MEM + hose->mem_resource->start)
+			start = PCIBIOS_MIN_MEM + hose->mem_resource->start;
+	}
+
+	return start;
+}
+
+static void pcibios_scanbus(struct pci_controller *hose)
+{
+	static int next_busno;
+	static int need_domain_info;
+	LIST_HEAD(resources);
+	struct pci_bus *bus;
+	struct pci_host_bridge *bridge;
+	int ret;
+
+	bridge = pci_alloc_host_bridge(0);
+	if (!bridge)
+		return;
+
+	if (hose->get_busno && pci_has_flag(PCI_PROBE_ONLY))
+		next_busno = (*hose->get_busno)();
+
+	pci_add_resource_offset(&resources,
+				hose->mem_resource, hose->mem_offset);
+	pci_add_resource_offset(&resources,
+				hose->io_resource, hose->io_offset);
+	list_splice_init(&resources, &bridge->windows);
+	bridge->dev.parent = NULL;
+	bridge->sysdata = hose;
+	bridge->busnr = next_busno;
+	bridge->ops = hose->pci_ops;
+	bridge->swizzle_irq = pci_common_swizzle;
+	bridge->map_irq = pcibios_map_irq;
+	ret = pci_scan_root_bus_bridge(bridge);
+	if (ret) {
+		pci_free_host_bridge(bridge);
+		return;
+	}
+
+	hose->bus = bus = bridge->bus;
+
+	need_domain_info = need_domain_info || pci_domain_nr(bus);
+	set_pci_need_domain_info(hose, need_domain_info);
+
+	next_busno = bus->busn_res.end + 1;
+	/* Don't allow 8-bit bus number overflow inside the hose -
+	   reserve some space for bridges. */
+	if (next_busno > 224) {
+		next_busno = 0;
+		need_domain_info = 1;
+	}
+
+	/*
+	 * We insert PCI resources into the iomem_resource and
+	 * ioport_resource trees in either pci_bus_claim_resources()
+	 * or pci_bus_assign_resources().
+	 */
+	if (pci_has_flag(PCI_PROBE_ONLY)) {
+		pci_bus_claim_resources(bus);
+	} else {
+		struct pci_bus *child;
+
+		pci_bus_size_bridges(bus);
+		pci_bus_assign_resources(bus);
+		list_for_each_entry(child, &bus->children, node)
+			pcie_bus_configure_settings(child);
+	}
+	pci_bus_add_devices(bus);
+}
+
+#ifdef CONFIG_OF
+void pci_load_of_ranges(struct pci_controller *hose, struct device_node *node)
+{
+	struct of_pci_range range;
+	struct of_pci_range_parser parser;
+
+	hose->of_node = node;
+
+	if (of_pci_range_parser_init(&parser, node))
+		return;
+
+	for_each_of_pci_range(&parser, &range) {
+		struct resource *res = NULL;
+
+		switch (range.flags & IORESOURCE_TYPE_BITS) {
+		case IORESOURCE_IO:
+			hose->io_map_base =
+				(unsigned long)ioremap(range.cpu_addr,
+						       range.size);
+			res = hose->io_resource;
+			break;
+		case IORESOURCE_MEM:
+			res = hose->mem_resource;
+			break;
+		}
+		if (res != NULL) {
+			res->name = node->full_name;
+			res->flags = range.flags;
+			res->start = range.cpu_addr;
+			res->end = range.cpu_addr + range.size - 1;
+			res->parent = res->child = res->sibling = NULL;
+		}
+	}
+}
+
+struct device_node *pcibios_get_phb_of_node(struct pci_bus *bus)
+{
+	struct pci_controller *hose = bus->sysdata;
+
+	return of_node_get(hose->of_node);
+}
+#endif
+
+static DEFINE_MUTEX(pci_scan_mutex);
+
+void register_pci_controller(struct pci_controller *hose)
+{
+	struct resource *parent;
+
+	parent = hose->mem_resource->parent;
+	if (!parent)
+		parent = &iomem_resource;
+
+	if (request_resource(parent, hose->mem_resource) < 0)
+		goto out;
+
+	parent = hose->io_resource->parent;
+	if (!parent)
+		parent = &ioport_resource;
+
+	if (request_resource(parent, hose->io_resource) < 0) {
+		release_resource(hose->mem_resource);
+		goto out;
+	}
+
+	INIT_LIST_HEAD(&hose->list);
+	list_add_tail(&hose->list, &controllers);
+
+	/*
+	 * Do not panic here but later - this might happen before console init.
+	 */
+	if (!hose->io_map_base) {
+		printk(KERN_WARNING
+		       "registering PCI controller with io_map_base unset\n");
+	}
+
+	/*
+	 * Scan the bus if it is register after the PCI subsystem
+	 * initialization.
+	 */
+	if (pci_initialized) {
+		mutex_lock(&pci_scan_mutex);
+		pcibios_scanbus(hose);
+		mutex_unlock(&pci_scan_mutex);
+	}
+
+	return;
+
+out:
+	printk(KERN_WARNING
+	       "Skipping PCI bus scan due to resource conflict\n");
+}
+
+static int __init pcibios_init(void)
+{
+	struct pci_controller *hose;
+
+	/* Scan all of the recorded PCI controllers.  */
+	list_for_each_entry(hose, &controllers, list)
+		pcibios_scanbus(hose);
+
+	pci_initialized = 1;
+
+	return 0;
+}
+
+subsys_initcall(pcibios_init);
+
+static int pcibios_enable_resources(struct pci_dev *dev, int mask)
+{
+	u16 cmd, old_cmd;
+	int idx;
+	struct resource *r;
+
+	pci_read_config_word(dev, PCI_COMMAND, &cmd);
+	old_cmd = cmd;
+	for (idx = 0; idx < PCI_NUM_RESOURCES; idx++) {
+		/* Only set up the requested stuff */
+		if (!(mask & (1<<idx)))
+			continue;
+
+		r = &dev->resource[idx];
+		if (!(r->flags & (IORESOURCE_IO | IORESOURCE_MEM)))
+			continue;
+		if ((idx == PCI_ROM_RESOURCE) &&
+				(!(r->flags & IORESOURCE_ROM_ENABLE)))
+			continue;
+		if (!r->start && r->end) {
+			pci_err(dev,
+				"can't enable device: resource collisions\n");
+			return -EINVAL;
+		}
+		if (r->flags & IORESOURCE_IO)
+			cmd |= PCI_COMMAND_IO;
+		if (r->flags & IORESOURCE_MEM)
+			cmd |= PCI_COMMAND_MEMORY;
+	}
+	if (cmd != old_cmd) {
+		pci_info(dev, "enabling device (%04x -> %04x)\n", old_cmd, cmd);
+		pci_write_config_word(dev, PCI_COMMAND, cmd);
+	}
+	return 0;
+}
+
+int pcibios_enable_device(struct pci_dev *dev, int mask)
+{
+	int err = pcibios_enable_resources(dev, mask);
+
+	if (err < 0)
+		return err;
+
+	return pcibios_plat_dev_init(dev);
+}
+
+void pcibios_fixup_bus(struct pci_bus *bus)
+{
+	struct pci_dev *dev = bus->self;
+
+	if (pci_has_flag(PCI_PROBE_ONLY) && dev &&
+	    (dev->class >> 8) == PCI_CLASS_BRIDGE_PCI) {
+		pci_read_bridge_bases(bus);
+	}
+}
+
+char * (*pcibios_plat_setup)(char *str) __initdata;
+
+char *__init pcibios_setup(char *str)
+{
+	if (pcibios_plat_setup)
+		return pcibios_plat_setup(str);
+	return str;
+}
diff --git a/arch/mips/pci/pci-malta.c b/arch/mips/pci/pci-malta.c
new file mode 100644
index 000000000..6aefdf20c
--- /dev/null
+++ b/arch/mips/pci/pci-malta.c
@@ -0,0 +1,242 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 1999, 2000, 2004, 2005	 MIPS Technologies, Inc.
+ *	All rights reserved.
+ *	Authors: Carsten Langgaard <carstenl@mips.com>
+ *		 Maciej W. Rozycki <macro@mips.com>
+ *
+ * Copyright (C) 2004 by Ralf Baechle (ralf@linux-mips.org)
+ *
+ * MIPS boards specific PCI support.
+ */
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+
+#include <asm/gt64120.h>
+#include <asm/mips-cps.h>
+#include <asm/mips-boards/generic.h>
+#include <asm/mips-boards/bonito64.h>
+#include <asm/mips-boards/msc01_pci.h>
+
+static struct resource bonito64_mem_resource = {
+	.name	= "Bonito PCI MEM",
+	.flags	= IORESOURCE_MEM,
+};
+
+static struct resource bonito64_io_resource = {
+	.name	= "Bonito PCI I/O",
+	.start	= 0x00000000UL,
+	.end	= 0x000fffffUL,
+	.flags	= IORESOURCE_IO,
+};
+
+static struct resource gt64120_mem_resource = {
+	.name	= "GT-64120 PCI MEM",
+	.flags	= IORESOURCE_MEM,
+};
+
+static struct resource gt64120_io_resource = {
+	.name	= "GT-64120 PCI I/O",
+	.flags	= IORESOURCE_IO,
+};
+
+static struct resource msc_mem_resource = {
+	.name	= "MSC PCI MEM",
+	.flags	= IORESOURCE_MEM,
+};
+
+static struct resource msc_io_resource = {
+	.name	= "MSC PCI I/O",
+	.flags	= IORESOURCE_IO,
+};
+
+extern struct pci_ops bonito64_pci_ops;
+extern struct pci_ops gt64xxx_pci0_ops;
+extern struct pci_ops msc_pci_ops;
+
+static struct pci_controller bonito64_controller = {
+	.pci_ops	= &bonito64_pci_ops,
+	.io_resource	= &bonito64_io_resource,
+	.mem_resource	= &bonito64_mem_resource,
+	.io_offset	= 0x00000000UL,
+};
+
+static struct pci_controller gt64120_controller = {
+	.pci_ops	= &gt64xxx_pci0_ops,
+	.io_resource	= &gt64120_io_resource,
+	.mem_resource	= &gt64120_mem_resource,
+};
+
+static struct pci_controller msc_controller = {
+	.pci_ops	= &msc_pci_ops,
+	.io_resource	= &msc_io_resource,
+	.mem_resource	= &msc_mem_resource,
+};
+
+void __init mips_pcibios_init(void)
+{
+	struct pci_controller *controller;
+	resource_size_t start, end, map, start1, end1, map1, map2, map3, mask;
+
+	switch (mips_revision_sconid) {
+	case MIPS_REVISION_SCON_GT64120:
+		/*
+		 * Due to a bug in the Galileo system controller, we need
+		 * to setup the PCI BAR for the Galileo internal registers.
+		 * This should be done in the bios/bootprom and will be
+		 * fixed in a later revision of YAMON (the MIPS boards
+		 * boot prom).
+		 */
+		GT_WRITE(GT_PCI0_CFGADDR_OFS,
+			 (0 << GT_PCI0_CFGADDR_BUSNUM_SHF) | /* Local bus */
+			 (0 << GT_PCI0_CFGADDR_DEVNUM_SHF) | /* GT64120 dev */
+			 (0 << GT_PCI0_CFGADDR_FUNCTNUM_SHF) | /* Function 0*/
+			 ((0x20/4) << GT_PCI0_CFGADDR_REGNUM_SHF) | /* BAR 4*/
+			 GT_PCI0_CFGADDR_CONFIGEN_BIT);
+
+		/* Perform the write */
+		GT_WRITE(GT_PCI0_CFGDATA_OFS, CPHYSADDR(MIPS_GT_BASE));
+
+		/* Set up resource ranges from the controller's registers.  */
+		start = GT_READ(GT_PCI0M0LD_OFS);
+		end = GT_READ(GT_PCI0M0HD_OFS);
+		map = GT_READ(GT_PCI0M0REMAP_OFS);
+		end = (end & GT_PCI_HD_MSK) | (start & ~GT_PCI_HD_MSK);
+		start1 = GT_READ(GT_PCI0M1LD_OFS);
+		end1 = GT_READ(GT_PCI0M1HD_OFS);
+		map1 = GT_READ(GT_PCI0M1REMAP_OFS);
+		end1 = (end1 & GT_PCI_HD_MSK) | (start1 & ~GT_PCI_HD_MSK);
+		/* Cannot support multiple windows, use the wider.  */
+		if (end1 - start1 > end - start) {
+			start = start1;
+			end = end1;
+			map = map1;
+		}
+		mask = ~(start ^ end);
+		/* We don't support remapping with a discontiguous mask.  */
+		BUG_ON((start & GT_PCI_HD_MSK) != (map & GT_PCI_HD_MSK) &&
+		       mask != ~((mask & -mask) - 1));
+		gt64120_mem_resource.start = start;
+		gt64120_mem_resource.end = end;
+		gt64120_controller.mem_offset = (start & mask) - (map & mask);
+		/* Addresses are 36-bit, so do shifts in the destinations.  */
+		gt64120_mem_resource.start <<= GT_PCI_DCRM_SHF;
+		gt64120_mem_resource.end <<= GT_PCI_DCRM_SHF;
+		gt64120_mem_resource.end |= (1 << GT_PCI_DCRM_SHF) - 1;
+		gt64120_controller.mem_offset <<= GT_PCI_DCRM_SHF;
+
+		start = GT_READ(GT_PCI0IOLD_OFS);
+		end = GT_READ(GT_PCI0IOHD_OFS);
+		map = GT_READ(GT_PCI0IOREMAP_OFS);
+		end = (end & GT_PCI_HD_MSK) | (start & ~GT_PCI_HD_MSK);
+		mask = ~(start ^ end);
+		/* We don't support remapping with a discontiguous mask.  */
+		BUG_ON((start & GT_PCI_HD_MSK) != (map & GT_PCI_HD_MSK) &&
+		       mask != ~((mask & -mask) - 1));
+		gt64120_io_resource.start = map & mask;
+		gt64120_io_resource.end = (map & mask) | ~mask;
+		gt64120_controller.io_offset = 0;
+		/* Addresses are 36-bit, so do shifts in the destinations.  */
+		gt64120_io_resource.start <<= GT_PCI_DCRM_SHF;
+		gt64120_io_resource.end <<= GT_PCI_DCRM_SHF;
+		gt64120_io_resource.end |= (1 << GT_PCI_DCRM_SHF) - 1;
+
+		controller = &gt64120_controller;
+		break;
+
+	case MIPS_REVISION_SCON_BONITO:
+		/* Set up resource ranges from the controller's registers.  */
+		map = BONITO_PCIMAP;
+		map1 = (BONITO_PCIMAP & BONITO_PCIMAP_PCIMAP_LO0) >>
+		       BONITO_PCIMAP_PCIMAP_LO0_SHIFT;
+		map2 = (BONITO_PCIMAP & BONITO_PCIMAP_PCIMAP_LO1) >>
+		       BONITO_PCIMAP_PCIMAP_LO1_SHIFT;
+		map3 = (BONITO_PCIMAP & BONITO_PCIMAP_PCIMAP_LO2) >>
+		       BONITO_PCIMAP_PCIMAP_LO2_SHIFT;
+		/* Combine as many adjacent windows as possible.  */
+		map = map1;
+		start = BONITO_PCILO0_BASE;
+		end = 1;
+		if (map3 == map2 + 1) {
+			map = map2;
+			start = BONITO_PCILO1_BASE;
+			end++;
+		}
+		if (map2 == map1 + 1) {
+			map = map1;
+			start = BONITO_PCILO0_BASE;
+			end++;
+		}
+		bonito64_mem_resource.start = start;
+		bonito64_mem_resource.end = start +
+					    BONITO_PCIMAP_WINBASE(end) - 1;
+		bonito64_controller.mem_offset = start -
+						 BONITO_PCIMAP_WINBASE(map);
+
+		controller = &bonito64_controller;
+		break;
+
+	case MIPS_REVISION_SCON_SOCIT:
+	case MIPS_REVISION_SCON_ROCIT:
+	case MIPS_REVISION_SCON_SOCITSC:
+	case MIPS_REVISION_SCON_SOCITSCP:
+		/* Set up resource ranges from the controller's registers.  */
+		MSC_READ(MSC01_PCI_SC2PMBASL, start);
+		MSC_READ(MSC01_PCI_SC2PMMSKL, mask);
+		MSC_READ(MSC01_PCI_SC2PMMAPL, map);
+		msc_mem_resource.start = start & mask;
+		msc_mem_resource.end = (start & mask) | ~mask;
+		msc_controller.mem_offset = (start & mask) - (map & mask);
+		if (mips_cps_numiocu(0)) {
+			write_gcr_reg0_base(start);
+			write_gcr_reg0_mask(mask |
+					    CM_GCR_REGn_MASK_CMTGT_IOCU0);
+		}
+		MSC_READ(MSC01_PCI_SC2PIOBASL, start);
+		MSC_READ(MSC01_PCI_SC2PIOMSKL, mask);
+		MSC_READ(MSC01_PCI_SC2PIOMAPL, map);
+		msc_io_resource.start = map & mask;
+		msc_io_resource.end = (map & mask) | ~mask;
+		msc_controller.io_offset = 0;
+		ioport_resource.end = ~mask;
+		if (mips_cps_numiocu(0)) {
+			write_gcr_reg1_base(start);
+			write_gcr_reg1_mask(mask |
+					    CM_GCR_REGn_MASK_CMTGT_IOCU0);
+		}
+		/* If ranges overlap I/O takes precedence.  */
+		start = start & mask;
+		end = start | ~mask;
+		if ((start >= msc_mem_resource.start &&
+		     start <= msc_mem_resource.end) ||
+		    (end >= msc_mem_resource.start &&
+		     end <= msc_mem_resource.end)) {
+			/* Use the larger space.  */
+			start = max(start, msc_mem_resource.start);
+			end = min(end, msc_mem_resource.end);
+			if (start - msc_mem_resource.start >=
+			    msc_mem_resource.end - end)
+				msc_mem_resource.end = start - 1;
+			else
+				msc_mem_resource.start = end + 1;
+		}
+
+		controller = &msc_controller;
+		break;
+	default:
+		return;
+	}
+
+	/* PIIX4 ACPI starts at 0x1000 */
+	if (controller->io_resource->start < 0x00001000UL)
+		controller->io_resource->start = 0x00001000UL;
+
+	iomem_resource.end &= 0xfffffffffULL;			/* 64 GB */
+	ioport_resource.end = controller->io_resource->end;
+
+	controller->io_map_base = mips_io_port_base;
+
+	register_pci_controller(controller);
+}
diff --git a/arch/mips/pci/pci-mt7620.c b/arch/mips/pci/pci-mt7620.c
new file mode 100644
index 000000000..e03293234
--- /dev/null
+++ b/arch/mips/pci/pci-mt7620.c
@@ -0,0 +1,421 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *  Ralink MT7620A SoC PCI support
+ *
+ *  Copyright (C) 2007-2013 Bruce Chang (Mediatek)
+ *  Copyright (C) 2013-2016 John Crispin <john@phrozen.org>
+ */
+
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/io.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_pci.h>
+#include <linux/reset.h>
+#include <linux/platform_device.h>
+
+#include <asm/mach-ralink/ralink_regs.h>
+#include <asm/mach-ralink/mt7620.h>
+
+#define RALINK_PCI_IO_MAP_BASE		0x10160000
+#define RALINK_PCI_MEMORY_BASE		0x0
+
+#define RALINK_INT_PCIE0		4
+
+#define RALINK_CLKCFG1			0x30
+#define RALINK_GPIOMODE			0x60
+
+#define PPLL_CFG1			0x9c
+#define PPLL_LD				BIT(23)
+
+#define PPLL_DRV			0xa0
+#define PDRV_SW_SET			BIT(31)
+#define LC_CKDRVPD			BIT(19)
+#define LC_CKDRVOHZ			BIT(18)
+#define LC_CKDRVHZ			BIT(17)
+#define LC_CKTEST			BIT(16)
+
+/* PCI Bridge registers */
+#define RALINK_PCI_PCICFG_ADDR		0x00
+#define PCIRST				BIT(1)
+
+#define RALINK_PCI_PCIENA		0x0C
+#define PCIINT2				BIT(20)
+
+#define RALINK_PCI_CONFIG_ADDR		0x20
+#define RALINK_PCI_CONFIG_DATA_VIRT_REG	0x24
+#define RALINK_PCI_MEMBASE		0x28
+#define RALINK_PCI_IOBASE		0x2C
+
+/* PCI RC registers */
+#define RALINK_PCI0_BAR0SETUP_ADDR	0x10
+#define RALINK_PCI0_IMBASEBAR0_ADDR	0x18
+#define RALINK_PCI0_ID			0x30
+#define RALINK_PCI0_CLASS		0x34
+#define RALINK_PCI0_SUBID		0x38
+#define RALINK_PCI0_STATUS		0x50
+#define PCIE_LINK_UP_ST			BIT(0)
+
+#define PCIEPHY0_CFG			0x90
+
+#define RALINK_PCIEPHY_P0_CTL_OFFSET	0x7498
+#define RALINK_PCIE0_CLK_EN		BIT(26)
+
+#define BUSY				0x80000000
+#define WAITRETRY_MAX			10
+#define WRITE_MODE			(1UL << 23)
+#define DATA_SHIFT			0
+#define ADDR_SHIFT			8
+
+
+static void __iomem *bridge_base;
+static void __iomem *pcie_base;
+
+static struct reset_control *rstpcie0;
+
+static inline void bridge_w32(u32 val, unsigned reg)
+{
+	iowrite32(val, bridge_base + reg);
+}
+
+static inline u32 bridge_r32(unsigned reg)
+{
+	return ioread32(bridge_base + reg);
+}
+
+static inline void pcie_w32(u32 val, unsigned reg)
+{
+	iowrite32(val, pcie_base + reg);
+}
+
+static inline u32 pcie_r32(unsigned reg)
+{
+	return ioread32(pcie_base + reg);
+}
+
+static inline void pcie_m32(u32 clr, u32 set, unsigned reg)
+{
+	u32 val = pcie_r32(reg);
+
+	val &= ~clr;
+	val |= set;
+	pcie_w32(val, reg);
+}
+
+static int wait_pciephy_busy(void)
+{
+	unsigned long reg_value = 0x0, retry = 0;
+
+	while (1) {
+		reg_value = pcie_r32(PCIEPHY0_CFG);
+
+		if (reg_value & BUSY)
+			mdelay(100);
+		else
+			break;
+		if (retry++ > WAITRETRY_MAX) {
+			pr_warn("PCIE-PHY retry failed.\n");
+			return -1;
+		}
+	}
+	return 0;
+}
+
+static void pcie_phy(unsigned long addr, unsigned long val)
+{
+	wait_pciephy_busy();
+	pcie_w32(WRITE_MODE | (val << DATA_SHIFT) | (addr << ADDR_SHIFT),
+		 PCIEPHY0_CFG);
+	mdelay(1);
+	wait_pciephy_busy();
+}
+
+static int pci_config_read(struct pci_bus *bus, unsigned int devfn, int where,
+			   int size, u32 *val)
+{
+	unsigned int slot = PCI_SLOT(devfn);
+	u8 func = PCI_FUNC(devfn);
+	u32 address;
+	u32 data;
+	u32 num = 0;
+
+	if (bus)
+		num = bus->number;
+
+	address = (((where & 0xF00) >> 8) << 24) | (num << 16) | (slot << 11) |
+		  (func << 8) | (where & 0xfc) | 0x80000000;
+	bridge_w32(address, RALINK_PCI_CONFIG_ADDR);
+	data = bridge_r32(RALINK_PCI_CONFIG_DATA_VIRT_REG);
+
+	switch (size) {
+	case 1:
+		*val = (data >> ((where & 3) << 3)) & 0xff;
+		break;
+	case 2:
+		*val = (data >> ((where & 3) << 3)) & 0xffff;
+		break;
+	case 4:
+		*val = data;
+		break;
+	}
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int pci_config_write(struct pci_bus *bus, unsigned int devfn, int where,
+			    int size, u32 val)
+{
+	unsigned int slot = PCI_SLOT(devfn);
+	u8 func = PCI_FUNC(devfn);
+	u32 address;
+	u32 data;
+	u32 num = 0;
+
+	if (bus)
+		num = bus->number;
+
+	address = (((where & 0xF00) >> 8) << 24) | (num << 16) | (slot << 11) |
+		  (func << 8) | (where & 0xfc) | 0x80000000;
+	bridge_w32(address, RALINK_PCI_CONFIG_ADDR);
+	data = bridge_r32(RALINK_PCI_CONFIG_DATA_VIRT_REG);
+
+	switch (size) {
+	case 1:
+		data = (data & ~(0xff << ((where & 3) << 3))) |
+			(val << ((where & 3) << 3));
+		break;
+	case 2:
+		data = (data & ~(0xffff << ((where & 3) << 3))) |
+			(val << ((where & 3) << 3));
+		break;
+	case 4:
+		data = val;
+		break;
+	}
+
+	bridge_w32(data, RALINK_PCI_CONFIG_DATA_VIRT_REG);
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+struct pci_ops mt7620_pci_ops = {
+	.read	= pci_config_read,
+	.write	= pci_config_write,
+};
+
+static struct resource mt7620_res_pci_mem1;
+static struct resource mt7620_res_pci_io1;
+struct pci_controller mt7620_controller = {
+	.pci_ops	= &mt7620_pci_ops,
+	.mem_resource	= &mt7620_res_pci_mem1,
+	.mem_offset	= 0x00000000UL,
+	.io_resource	= &mt7620_res_pci_io1,
+	.io_offset	= 0x00000000UL,
+	.io_map_base	= 0xa0000000,
+};
+
+static int mt7620_pci_hw_init(struct platform_device *pdev)
+{
+	/* bypass PCIe DLL */
+	pcie_phy(0x0, 0x80);
+	pcie_phy(0x1, 0x04);
+
+	/* Elastic buffer control */
+	pcie_phy(0x68, 0xB4);
+
+	/* put core into reset */
+	pcie_m32(0, PCIRST, RALINK_PCI_PCICFG_ADDR);
+	reset_control_assert(rstpcie0);
+
+	/* disable power and all clocks */
+	rt_sysc_m32(RALINK_PCIE0_CLK_EN, 0, RALINK_CLKCFG1);
+	rt_sysc_m32(LC_CKDRVPD, PDRV_SW_SET, PPLL_DRV);
+
+	/* bring core out of reset */
+	reset_control_deassert(rstpcie0);
+	rt_sysc_m32(0, RALINK_PCIE0_CLK_EN, RALINK_CLKCFG1);
+	mdelay(100);
+
+	if (!(rt_sysc_r32(PPLL_CFG1) & PPLL_LD)) {
+		dev_err(&pdev->dev, "pcie PLL not locked, aborting init\n");
+		reset_control_assert(rstpcie0);
+		rt_sysc_m32(RALINK_PCIE0_CLK_EN, 0, RALINK_CLKCFG1);
+		return -1;
+	}
+
+	/* power up the bus */
+	rt_sysc_m32(LC_CKDRVHZ | LC_CKDRVOHZ, LC_CKDRVPD | PDRV_SW_SET,
+		    PPLL_DRV);
+
+	return 0;
+}
+
+static int mt7628_pci_hw_init(struct platform_device *pdev)
+{
+	u32 val = 0;
+
+	/* bring the core out of reset */
+	rt_sysc_m32(BIT(16), 0, RALINK_GPIOMODE);
+	reset_control_deassert(rstpcie0);
+
+	/* enable the pci clk */
+	rt_sysc_m32(0, RALINK_PCIE0_CLK_EN, RALINK_CLKCFG1);
+	mdelay(100);
+
+	/* voodoo from the SDK driver */
+	pcie_m32(~0xff, 0x5, RALINK_PCIEPHY_P0_CTL_OFFSET);
+
+	pci_config_read(NULL, 0, 0x70c, 4, &val);
+	val &= ~(0xff) << 8;
+	val |= 0x50 << 8;
+	pci_config_write(NULL, 0, 0x70c, 4, val);
+
+	pci_config_read(NULL, 0, 0x70c, 4, &val);
+	dev_err(&pdev->dev, "Port 0 N_FTS = %x\n", (unsigned int) val);
+
+	return 0;
+}
+
+static int mt7620_pci_probe(struct platform_device *pdev)
+{
+	struct resource *bridge_res = platform_get_resource(pdev,
+							    IORESOURCE_MEM, 0);
+	struct resource *pcie_res = platform_get_resource(pdev,
+							  IORESOURCE_MEM, 1);
+	u32 val = 0;
+
+	rstpcie0 = devm_reset_control_get_exclusive(&pdev->dev, "pcie0");
+	if (IS_ERR(rstpcie0))
+		return PTR_ERR(rstpcie0);
+
+	bridge_base = devm_ioremap_resource(&pdev->dev, bridge_res);
+	if (IS_ERR(bridge_base))
+		return PTR_ERR(bridge_base);
+
+	pcie_base = devm_ioremap_resource(&pdev->dev, pcie_res);
+	if (IS_ERR(pcie_base))
+		return PTR_ERR(pcie_base);
+
+	iomem_resource.start = 0;
+	iomem_resource.end = ~0;
+	ioport_resource.start = 0;
+	ioport_resource.end = ~0;
+
+	/* bring up the pci core */
+	switch (ralink_soc) {
+	case MT762X_SOC_MT7620A:
+		if (mt7620_pci_hw_init(pdev))
+			return -1;
+		break;
+
+	case MT762X_SOC_MT7628AN:
+	case MT762X_SOC_MT7688:
+		if (mt7628_pci_hw_init(pdev))
+			return -1;
+		break;
+
+	default:
+		dev_err(&pdev->dev, "pcie is not supported on this hardware\n");
+		return -1;
+	}
+	mdelay(50);
+
+	/* enable write access */
+	pcie_m32(PCIRST, 0, RALINK_PCI_PCICFG_ADDR);
+	mdelay(100);
+
+	/* check if there is a card present */
+	if ((pcie_r32(RALINK_PCI0_STATUS) & PCIE_LINK_UP_ST) == 0) {
+		reset_control_assert(rstpcie0);
+		rt_sysc_m32(RALINK_PCIE0_CLK_EN, 0, RALINK_CLKCFG1);
+		if (ralink_soc == MT762X_SOC_MT7620A)
+			rt_sysc_m32(LC_CKDRVPD, PDRV_SW_SET, PPLL_DRV);
+		dev_err(&pdev->dev, "PCIE0 no card, disable it(RST&CLK)\n");
+		return -1;
+	}
+
+	/* setup ranges */
+	bridge_w32(0xffffffff, RALINK_PCI_MEMBASE);
+	bridge_w32(RALINK_PCI_IO_MAP_BASE, RALINK_PCI_IOBASE);
+
+	pcie_w32(0x7FFF0001, RALINK_PCI0_BAR0SETUP_ADDR);
+	pcie_w32(RALINK_PCI_MEMORY_BASE, RALINK_PCI0_IMBASEBAR0_ADDR);
+	pcie_w32(0x06040001, RALINK_PCI0_CLASS);
+
+	/* enable interrupts */
+	pcie_m32(0, PCIINT2, RALINK_PCI_PCIENA);
+
+	/* voodoo from the SDK driver */
+	pci_config_read(NULL, 0, 4, 4, &val);
+	pci_config_write(NULL, 0, 4, 4, val | 0x7);
+
+	pci_load_of_ranges(&mt7620_controller, pdev->dev.of_node);
+	register_pci_controller(&mt7620_controller);
+
+	return 0;
+}
+
+int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	u16 cmd;
+	u32 val;
+	int irq = 0;
+
+	if ((dev->bus->number == 0) && (slot == 0)) {
+		pcie_w32(0x7FFF0001, RALINK_PCI0_BAR0SETUP_ADDR);
+		pci_config_write(dev->bus, 0, PCI_BASE_ADDRESS_0, 4,
+				 RALINK_PCI_MEMORY_BASE);
+		pci_config_read(dev->bus, 0, PCI_BASE_ADDRESS_0, 4, &val);
+	} else if ((dev->bus->number == 1) && (slot == 0x0)) {
+		irq = RALINK_INT_PCIE0;
+	} else {
+		dev_err(&dev->dev, "no irq found - bus=0x%x, slot = 0x%x\n",
+			dev->bus->number, slot);
+		return 0;
+	}
+	dev_err(&dev->dev, "card - bus=0x%x, slot = 0x%x irq=%d\n",
+		dev->bus->number, slot, irq);
+
+	/* configure the cache line size to 0x14 */
+	pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, 0x14);
+
+	/* configure latency timer to 0xff */
+	pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0xff);
+	pci_read_config_word(dev, PCI_COMMAND, &cmd);
+
+	/* setup the slot */
+	cmd = cmd | PCI_COMMAND_MASTER | PCI_COMMAND_IO | PCI_COMMAND_MEMORY;
+	pci_write_config_word(dev, PCI_COMMAND, cmd);
+	pci_write_config_byte(dev, PCI_INTERRUPT_LINE, dev->irq);
+
+	return irq;
+}
+
+int pcibios_plat_dev_init(struct pci_dev *dev)
+{
+	return 0;
+}
+
+static const struct of_device_id mt7620_pci_ids[] = {
+	{ .compatible = "mediatek,mt7620-pci" },
+	{},
+};
+
+static struct platform_driver mt7620_pci_driver = {
+	.probe = mt7620_pci_probe,
+	.driver = {
+		.name = "mt7620-pci",
+		.of_match_table = of_match_ptr(mt7620_pci_ids),
+	},
+};
+
+static int __init mt7620_pci_init(void)
+{
+	return platform_driver_register(&mt7620_pci_driver);
+}
+
+arch_initcall(mt7620_pci_init);
diff --git a/arch/mips/pci/pci-octeon.c b/arch/mips/pci/pci-octeon.c
new file mode 100644
index 000000000..e457a18cb
--- /dev/null
+++ b/arch/mips/pci/pci-octeon.c
@@ -0,0 +1,711 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2005-2009 Cavium Networks
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/pci.h>
+#include <linux/interrupt.h>
+#include <linux/time.h>
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/swiotlb.h>
+
+#include <asm/time.h>
+
+#include <asm/octeon/octeon.h>
+#include <asm/octeon/cvmx-npi-defs.h>
+#include <asm/octeon/cvmx-pci-defs.h>
+#include <asm/octeon/pci-octeon.h>
+
+#define USE_OCTEON_INTERNAL_ARBITER
+
+/*
+ * Octeon's PCI controller uses did=3, subdid=2 for PCI IO
+ * addresses. Use PCI endian swapping 1 so no address swapping is
+ * necessary. The Linux io routines will endian swap the data.
+ */
+#define OCTEON_PCI_IOSPACE_BASE	    0x80011a0400000000ull
+#define OCTEON_PCI_IOSPACE_SIZE	    (1ull<<32)
+
+/* Octeon't PCI controller uses did=3, subdid=3 for PCI memory. */
+#define OCTEON_PCI_MEMSPACE_OFFSET  (0x00011b0000000000ull)
+
+u64 octeon_bar1_pci_phys;
+
+/**
+ * This is the bit decoding used for the Octeon PCI controller addresses
+ */
+union octeon_pci_address {
+	uint64_t u64;
+	struct {
+		uint64_t upper:2;
+		uint64_t reserved:13;
+		uint64_t io:1;
+		uint64_t did:5;
+		uint64_t subdid:3;
+		uint64_t reserved2:4;
+		uint64_t endian_swap:2;
+		uint64_t reserved3:10;
+		uint64_t bus:8;
+		uint64_t dev:5;
+		uint64_t func:3;
+		uint64_t reg:8;
+	} s;
+};
+
+int (*octeon_pcibios_map_irq)(const struct pci_dev *dev, u8 slot, u8 pin);
+enum octeon_dma_bar_type octeon_dma_bar_type = OCTEON_DMA_BAR_TYPE_INVALID;
+
+/**
+ * Map a PCI device to the appropriate interrupt line
+ *
+ * @dev:    The Linux PCI device structure for the device to map
+ * @slot:   The slot number for this device on __BUS 0__. Linux
+ *		 enumerates through all the bridges and figures out the
+ *		 slot on Bus 0 where this device eventually hooks to.
+ * @pin:    The PCI interrupt pin read from the device, then swizzled
+ *		 as it goes through each bridge.
+ * Returns Interrupt number for the device
+ */
+int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	if (octeon_pcibios_map_irq)
+		return octeon_pcibios_map_irq(dev, slot, pin);
+	else
+		panic("octeon_pcibios_map_irq not set.");
+}
+
+
+/*
+ * Called to perform platform specific PCI setup
+ */
+int pcibios_plat_dev_init(struct pci_dev *dev)
+{
+	uint16_t config;
+	uint32_t dconfig;
+	int pos;
+	/*
+	 * Force the Cache line setting to 64 bytes. The standard
+	 * Linux bus scan doesn't seem to set it. Octeon really has
+	 * 128 byte lines, but Intel bridges get really upset if you
+	 * try and set values above 64 bytes. Value is specified in
+	 * 32bit words.
+	 */
+	pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, 64 / 4);
+	/* Set latency timers for all devices */
+	pci_write_config_byte(dev, PCI_LATENCY_TIMER, 64);
+
+	/* Enable reporting System errors and parity errors on all devices */
+	/* Enable parity checking and error reporting */
+	pci_read_config_word(dev, PCI_COMMAND, &config);
+	config |= PCI_COMMAND_PARITY | PCI_COMMAND_SERR;
+	pci_write_config_word(dev, PCI_COMMAND, config);
+
+	if (dev->subordinate) {
+		/* Set latency timers on sub bridges */
+		pci_write_config_byte(dev, PCI_SEC_LATENCY_TIMER, 64);
+		/* More bridge error detection */
+		pci_read_config_word(dev, PCI_BRIDGE_CONTROL, &config);
+		config |= PCI_BRIDGE_CTL_PARITY | PCI_BRIDGE_CTL_SERR;
+		pci_write_config_word(dev, PCI_BRIDGE_CONTROL, config);
+	}
+
+	/* Enable the PCIe normal error reporting */
+	config = PCI_EXP_DEVCTL_CERE; /* Correctable Error Reporting */
+	config |= PCI_EXP_DEVCTL_NFERE; /* Non-Fatal Error Reporting */
+	config |= PCI_EXP_DEVCTL_FERE;	/* Fatal Error Reporting */
+	config |= PCI_EXP_DEVCTL_URRE;	/* Unsupported Request */
+	pcie_capability_set_word(dev, PCI_EXP_DEVCTL, config);
+
+	/* Find the Advanced Error Reporting capability */
+	pos = pci_find_ext_capability(dev, PCI_EXT_CAP_ID_ERR);
+	if (pos) {
+		/* Clear Uncorrectable Error Status */
+		pci_read_config_dword(dev, pos + PCI_ERR_UNCOR_STATUS,
+				      &dconfig);
+		pci_write_config_dword(dev, pos + PCI_ERR_UNCOR_STATUS,
+				       dconfig);
+		/* Enable reporting of all uncorrectable errors */
+		/* Uncorrectable Error Mask - turned on bits disable errors */
+		pci_write_config_dword(dev, pos + PCI_ERR_UNCOR_MASK, 0);
+		/*
+		 * Leave severity at HW default. This only controls if
+		 * errors are reported as uncorrectable or
+		 * correctable, not if the error is reported.
+		 */
+		/* PCI_ERR_UNCOR_SEVER - Uncorrectable Error Severity */
+		/* Clear Correctable Error Status */
+		pci_read_config_dword(dev, pos + PCI_ERR_COR_STATUS, &dconfig);
+		pci_write_config_dword(dev, pos + PCI_ERR_COR_STATUS, dconfig);
+		/* Enable reporting of all correctable errors */
+		/* Correctable Error Mask - turned on bits disable errors */
+		pci_write_config_dword(dev, pos + PCI_ERR_COR_MASK, 0);
+		/* Advanced Error Capabilities */
+		pci_read_config_dword(dev, pos + PCI_ERR_CAP, &dconfig);
+		/* ECRC Generation Enable */
+		if (config & PCI_ERR_CAP_ECRC_GENC)
+			config |= PCI_ERR_CAP_ECRC_GENE;
+		/* ECRC Check Enable */
+		if (config & PCI_ERR_CAP_ECRC_CHKC)
+			config |= PCI_ERR_CAP_ECRC_CHKE;
+		pci_write_config_dword(dev, pos + PCI_ERR_CAP, dconfig);
+		/* PCI_ERR_HEADER_LOG - Header Log Register (16 bytes) */
+		/* Report all errors to the root complex */
+		pci_write_config_dword(dev, pos + PCI_ERR_ROOT_COMMAND,
+				       PCI_ERR_ROOT_CMD_COR_EN |
+				       PCI_ERR_ROOT_CMD_NONFATAL_EN |
+				       PCI_ERR_ROOT_CMD_FATAL_EN);
+		/* Clear the Root status register */
+		pci_read_config_dword(dev, pos + PCI_ERR_ROOT_STATUS, &dconfig);
+		pci_write_config_dword(dev, pos + PCI_ERR_ROOT_STATUS, dconfig);
+	}
+
+	return 0;
+}
+
+/**
+ * Return the mapping of PCI device number to IRQ line. Each
+ * character in the return string represents the interrupt
+ * line for the device at that position. Device 1 maps to the
+ * first character, etc. The characters A-D are used for PCI
+ * interrupts.
+ *
+ * Returns PCI interrupt mapping
+ */
+const char *octeon_get_pci_interrupts(void)
+{
+	/*
+	 * Returning an empty string causes the interrupts to be
+	 * routed based on the PCI specification. From the PCI spec:
+	 *
+	 * INTA# of Device Number 0 is connected to IRQW on the system
+	 * board.  (Device Number has no significance regarding being
+	 * located on the system board or in a connector.) INTA# of
+	 * Device Number 1 is connected to IRQX on the system
+	 * board. INTA# of Device Number 2 is connected to IRQY on the
+	 * system board. INTA# of Device Number 3 is connected to IRQZ
+	 * on the system board. The table below describes how each
+	 * agent's INTx# lines are connected to the system board
+	 * interrupt lines. The following equation can be used to
+	 * determine to which INTx# signal on the system board a given
+	 * device's INTx# line(s) is connected.
+	 *
+	 * MB = (D + I) MOD 4 MB = System board Interrupt (IRQW = 0,
+	 * IRQX = 1, IRQY = 2, and IRQZ = 3) D = Device Number I =
+	 * Interrupt Number (INTA# = 0, INTB# = 1, INTC# = 2, and
+	 * INTD# = 3)
+	 */
+	if (of_machine_is_compatible("dlink,dsr-500n"))
+		return "CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC";
+	switch (octeon_bootinfo->board_type) {
+	case CVMX_BOARD_TYPE_NAO38:
+		/* This is really the NAC38 */
+		return "AAAAADABAAAAAAAAAAAAAAAAAAAAAAAA";
+	case CVMX_BOARD_TYPE_EBH3100:
+	case CVMX_BOARD_TYPE_CN3010_EVB_HS5:
+	case CVMX_BOARD_TYPE_CN3005_EVB_HS5:
+		return "AAABAAAAAAAAAAAAAAAAAAAAAAAAAAAA";
+	case CVMX_BOARD_TYPE_BBGW_REF:
+		return "AABCD";
+	case CVMX_BOARD_TYPE_CUST_DSR1000N:
+		return "CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC";
+	case CVMX_BOARD_TYPE_THUNDER:
+	case CVMX_BOARD_TYPE_EBH3000:
+	default:
+		return "";
+	}
+}
+
+/**
+ * Map a PCI device to the appropriate interrupt line
+ *
+ * @dev:    The Linux PCI device structure for the device to map
+ * @slot:   The slot number for this device on __BUS 0__. Linux
+ *		 enumerates through all the bridges and figures out the
+ *		 slot on Bus 0 where this device eventually hooks to.
+ * @pin:    The PCI interrupt pin read from the device, then swizzled
+ *		 as it goes through each bridge.
+ * Returns Interrupt number for the device
+ */
+int __init octeon_pci_pcibios_map_irq(const struct pci_dev *dev,
+				      u8 slot, u8 pin)
+{
+	int irq_num;
+	const char *interrupts;
+	int dev_num;
+
+	/* Get the board specific interrupt mapping */
+	interrupts = octeon_get_pci_interrupts();
+
+	dev_num = dev->devfn >> 3;
+	if (dev_num < strlen(interrupts))
+		irq_num = ((interrupts[dev_num] - 'A' + pin - 1) & 3) +
+			OCTEON_IRQ_PCI_INT0;
+	else
+		irq_num = ((slot + pin - 3) & 3) + OCTEON_IRQ_PCI_INT0;
+	return irq_num;
+}
+
+
+/*
+ * Read a value from configuration space
+ */
+static int octeon_read_config(struct pci_bus *bus, unsigned int devfn,
+			      int reg, int size, u32 *val)
+{
+	union octeon_pci_address pci_addr;
+
+	pci_addr.u64 = 0;
+	pci_addr.s.upper = 2;
+	pci_addr.s.io = 1;
+	pci_addr.s.did = 3;
+	pci_addr.s.subdid = 1;
+	pci_addr.s.endian_swap = 1;
+	pci_addr.s.bus = bus->number;
+	pci_addr.s.dev = devfn >> 3;
+	pci_addr.s.func = devfn & 0x7;
+	pci_addr.s.reg = reg;
+
+	switch (size) {
+	case 4:
+		*val = le32_to_cpu(cvmx_read64_uint32(pci_addr.u64));
+		return PCIBIOS_SUCCESSFUL;
+	case 2:
+		*val = le16_to_cpu(cvmx_read64_uint16(pci_addr.u64));
+		return PCIBIOS_SUCCESSFUL;
+	case 1:
+		*val = cvmx_read64_uint8(pci_addr.u64);
+		return PCIBIOS_SUCCESSFUL;
+	}
+	return PCIBIOS_FUNC_NOT_SUPPORTED;
+}
+
+
+/*
+ * Write a value to PCI configuration space
+ */
+static int octeon_write_config(struct pci_bus *bus, unsigned int devfn,
+			       int reg, int size, u32 val)
+{
+	union octeon_pci_address pci_addr;
+
+	pci_addr.u64 = 0;
+	pci_addr.s.upper = 2;
+	pci_addr.s.io = 1;
+	pci_addr.s.did = 3;
+	pci_addr.s.subdid = 1;
+	pci_addr.s.endian_swap = 1;
+	pci_addr.s.bus = bus->number;
+	pci_addr.s.dev = devfn >> 3;
+	pci_addr.s.func = devfn & 0x7;
+	pci_addr.s.reg = reg;
+
+	switch (size) {
+	case 4:
+		cvmx_write64_uint32(pci_addr.u64, cpu_to_le32(val));
+		return PCIBIOS_SUCCESSFUL;
+	case 2:
+		cvmx_write64_uint16(pci_addr.u64, cpu_to_le16(val));
+		return PCIBIOS_SUCCESSFUL;
+	case 1:
+		cvmx_write64_uint8(pci_addr.u64, val);
+		return PCIBIOS_SUCCESSFUL;
+	}
+	return PCIBIOS_FUNC_NOT_SUPPORTED;
+}
+
+
+static struct pci_ops octeon_pci_ops = {
+	.read	= octeon_read_config,
+	.write	= octeon_write_config,
+};
+
+static struct resource octeon_pci_mem_resource = {
+	.start = 0,
+	.end = 0,
+	.name = "Octeon PCI MEM",
+	.flags = IORESOURCE_MEM,
+};
+
+/*
+ * PCI ports must be above 16KB so the ISA bus filtering in the PCI-X to PCI
+ * bridge
+ */
+static struct resource octeon_pci_io_resource = {
+	.start = 0x4000,
+	.end = OCTEON_PCI_IOSPACE_SIZE - 1,
+	.name = "Octeon PCI IO",
+	.flags = IORESOURCE_IO,
+};
+
+static struct pci_controller octeon_pci_controller = {
+	.pci_ops = &octeon_pci_ops,
+	.mem_resource = &octeon_pci_mem_resource,
+	.mem_offset = OCTEON_PCI_MEMSPACE_OFFSET,
+	.io_resource = &octeon_pci_io_resource,
+	.io_offset = 0,
+	.io_map_base = OCTEON_PCI_IOSPACE_BASE,
+};
+
+
+/*
+ * Low level initialize the Octeon PCI controller
+ */
+static void octeon_pci_initialize(void)
+{
+	union cvmx_pci_cfg01 cfg01;
+	union cvmx_npi_ctl_status ctl_status;
+	union cvmx_pci_ctl_status_2 ctl_status_2;
+	union cvmx_pci_cfg19 cfg19;
+	union cvmx_pci_cfg16 cfg16;
+	union cvmx_pci_cfg22 cfg22;
+	union cvmx_pci_cfg56 cfg56;
+
+	/* Reset the PCI Bus */
+	cvmx_write_csr(CVMX_CIU_SOFT_PRST, 0x1);
+	cvmx_read_csr(CVMX_CIU_SOFT_PRST);
+
+	udelay(2000);		/* Hold PCI reset for 2 ms */
+
+	ctl_status.u64 = 0;	/* cvmx_read_csr(CVMX_NPI_CTL_STATUS); */
+	ctl_status.s.max_word = 1;
+	ctl_status.s.timer = 1;
+	cvmx_write_csr(CVMX_NPI_CTL_STATUS, ctl_status.u64);
+
+	/* Deassert PCI reset and advertize PCX Host Mode Device Capability
+	   (64b) */
+	cvmx_write_csr(CVMX_CIU_SOFT_PRST, 0x4);
+	cvmx_read_csr(CVMX_CIU_SOFT_PRST);
+
+	udelay(2000);		/* Wait 2 ms after deasserting PCI reset */
+
+	ctl_status_2.u32 = 0;
+	ctl_status_2.s.tsr_hwm = 1;	/* Initializes to 0.  Must be set
+					   before any PCI reads. */
+	ctl_status_2.s.bar2pres = 1;	/* Enable BAR2 */
+	ctl_status_2.s.bar2_enb = 1;
+	ctl_status_2.s.bar2_cax = 1;	/* Don't use L2 */
+	ctl_status_2.s.bar2_esx = 1;
+	ctl_status_2.s.pmo_amod = 1;	/* Round robin priority */
+	if (octeon_dma_bar_type == OCTEON_DMA_BAR_TYPE_BIG) {
+		/* BAR1 hole */
+		ctl_status_2.s.bb1_hole = OCTEON_PCI_BAR1_HOLE_BITS;
+		ctl_status_2.s.bb1_siz = 1;  /* BAR1 is 2GB */
+		ctl_status_2.s.bb_ca = 1;    /* Don't use L2 with big bars */
+		ctl_status_2.s.bb_es = 1;    /* Big bar in byte swap mode */
+		ctl_status_2.s.bb1 = 1;	     /* BAR1 is big */
+		ctl_status_2.s.bb0 = 1;	     /* BAR0 is big */
+	}
+
+	octeon_npi_write32(CVMX_NPI_PCI_CTL_STATUS_2, ctl_status_2.u32);
+	udelay(2000);		/* Wait 2 ms before doing PCI reads */
+
+	ctl_status_2.u32 = octeon_npi_read32(CVMX_NPI_PCI_CTL_STATUS_2);
+	pr_notice("PCI Status: %s %s-bit\n",
+		  ctl_status_2.s.ap_pcix ? "PCI-X" : "PCI",
+		  ctl_status_2.s.ap_64ad ? "64" : "32");
+
+	if (OCTEON_IS_MODEL(OCTEON_CN58XX) || OCTEON_IS_MODEL(OCTEON_CN50XX)) {
+		union cvmx_pci_cnt_reg cnt_reg_start;
+		union cvmx_pci_cnt_reg cnt_reg_end;
+		unsigned long cycles, pci_clock;
+
+		cnt_reg_start.u64 = cvmx_read_csr(CVMX_NPI_PCI_CNT_REG);
+		cycles = read_c0_cvmcount();
+		udelay(1000);
+		cnt_reg_end.u64 = cvmx_read_csr(CVMX_NPI_PCI_CNT_REG);
+		cycles = read_c0_cvmcount() - cycles;
+		pci_clock = (cnt_reg_end.s.pcicnt - cnt_reg_start.s.pcicnt) /
+			    (cycles / (mips_hpt_frequency / 1000000));
+		pr_notice("PCI Clock: %lu MHz\n", pci_clock);
+	}
+
+	/*
+	 * TDOMC must be set to one in PCI mode. TDOMC should be set to 4
+	 * in PCI-X mode to allow four outstanding splits. Otherwise,
+	 * should not change from its reset value. Don't write PCI_CFG19
+	 * in PCI mode (0x82000001 reset value), write it to 0x82000004
+	 * after PCI-X mode is known. MRBCI,MDWE,MDRE -> must be zero.
+	 * MRBCM -> must be one.
+	 */
+	if (ctl_status_2.s.ap_pcix) {
+		cfg19.u32 = 0;
+		/*
+		 * Target Delayed/Split request outstanding maximum
+		 * count. [1..31] and 0=32.  NOTE: If the user
+		 * programs these bits beyond the Designed Maximum
+		 * outstanding count, then the designed maximum table
+		 * depth will be used instead.	No additional
+		 * Deferred/Split transactions will be accepted if
+		 * this outstanding maximum count is
+		 * reached. Furthermore, no additional deferred/split
+		 * transactions will be accepted if the I/O delay/ I/O
+		 * Split Request outstanding maximum is reached.
+		 */
+		cfg19.s.tdomc = 4;
+		/*
+		 * Master Deferred Read Request Outstanding Max Count
+		 * (PCI only).	CR4C[26:24] Max SAC cycles MAX DAC
+		 * cycles 000 8 4 001 1 0 010 2 1 011 3 1 100 4 2 101
+		 * 5 2 110 6 3 111 7 3 For example, if these bits are
+		 * programmed to 100, the core can support 2 DAC
+		 * cycles, 4 SAC cycles or a combination of 1 DAC and
+		 * 2 SAC cycles. NOTE: For the PCI-X maximum
+		 * outstanding split transactions, refer to
+		 * CRE0[22:20].
+		 */
+		cfg19.s.mdrrmc = 2;
+		/*
+		 * Master Request (Memory Read) Byte Count/Byte Enable
+		 * select. 0 = Byte Enables valid. In PCI mode, a
+		 * burst transaction cannot be performed using Memory
+		 * Read command=4?h6. 1 = DWORD Byte Count valid
+		 * (default). In PCI Mode, the memory read byte
+		 * enables are automatically generated by the
+		 * core. Note: N3 Master Request transaction sizes are
+		 * always determined through the
+		 * am_attr[<35:32>|<7:0>] field.
+		 */
+		cfg19.s.mrbcm = 1;
+		octeon_npi_write32(CVMX_NPI_PCI_CFG19, cfg19.u32);
+	}
+
+
+	cfg01.u32 = 0;
+	cfg01.s.msae = 1;	/* Memory Space Access Enable */
+	cfg01.s.me = 1;		/* Master Enable */
+	cfg01.s.pee = 1;	/* PERR# Enable */
+	cfg01.s.see = 1;	/* System Error Enable */
+	cfg01.s.fbbe = 1;	/* Fast Back to Back Transaction Enable */
+
+	octeon_npi_write32(CVMX_NPI_PCI_CFG01, cfg01.u32);
+
+#ifdef USE_OCTEON_INTERNAL_ARBITER
+	/*
+	 * When OCTEON is a PCI host, most systems will use OCTEON's
+	 * internal arbiter, so must enable it before any PCI/PCI-X
+	 * traffic can occur.
+	 */
+	{
+		union cvmx_npi_pci_int_arb_cfg pci_int_arb_cfg;
+
+		pci_int_arb_cfg.u64 = 0;
+		pci_int_arb_cfg.s.en = 1;	/* Internal arbiter enable */
+		cvmx_write_csr(CVMX_NPI_PCI_INT_ARB_CFG, pci_int_arb_cfg.u64);
+	}
+#endif	/* USE_OCTEON_INTERNAL_ARBITER */
+
+	/*
+	 * Preferably written to 1 to set MLTD. [RDSATI,TRTAE,
+	 * TWTAE,TMAE,DPPMR -> must be zero. TILT -> must not be set to
+	 * 1..7.
+	 */
+	cfg16.u32 = 0;
+	cfg16.s.mltd = 1;	/* Master Latency Timer Disable */
+	octeon_npi_write32(CVMX_NPI_PCI_CFG16, cfg16.u32);
+
+	/*
+	 * Should be written to 0x4ff00. MTTV -> must be zero.
+	 * FLUSH -> must be 1. MRV -> should be 0xFF.
+	 */
+	cfg22.u32 = 0;
+	/* Master Retry Value [1..255] and 0=infinite */
+	cfg22.s.mrv = 0xff;
+	/*
+	 * AM_DO_FLUSH_I control NOTE: This bit MUST BE ONE for proper
+	 * N3K operation.
+	 */
+	cfg22.s.flush = 1;
+	octeon_npi_write32(CVMX_NPI_PCI_CFG22, cfg22.u32);
+
+	/*
+	 * MOST Indicates the maximum number of outstanding splits (in -1
+	 * notation) when OCTEON is in PCI-X mode.  PCI-X performance is
+	 * affected by the MOST selection.  Should generally be written
+	 * with one of 0x3be807, 0x2be807, 0x1be807, or 0x0be807,
+	 * depending on the desired MOST of 3, 2, 1, or 0, respectively.
+	 */
+	cfg56.u32 = 0;
+	cfg56.s.pxcid = 7;	/* RO - PCI-X Capability ID */
+	cfg56.s.ncp = 0xe8;	/* RO - Next Capability Pointer */
+	cfg56.s.dpere = 1;	/* Data Parity Error Recovery Enable */
+	cfg56.s.roe = 1;	/* Relaxed Ordering Enable */
+	cfg56.s.mmbc = 1;	/* Maximum Memory Byte Count
+				   [0=512B,1=1024B,2=2048B,3=4096B] */
+	cfg56.s.most = 3;	/* Maximum outstanding Split transactions [0=1
+				   .. 7=32] */
+
+	octeon_npi_write32(CVMX_NPI_PCI_CFG56, cfg56.u32);
+
+	/*
+	 * Affects PCI performance when OCTEON services reads to its
+	 * BAR1/BAR2. Refer to Section 10.6.1.	The recommended values are
+	 * 0x22, 0x33, and 0x33 for PCI_READ_CMD_6, PCI_READ_CMD_C, and
+	 * PCI_READ_CMD_E, respectively. Unfortunately due to errata DDR-700,
+	 * these values need to be changed so they won't possibly prefetch off
+	 * of the end of memory if PCI is DMAing a buffer at the end of
+	 * memory. Note that these values differ from their reset values.
+	 */
+	octeon_npi_write32(CVMX_NPI_PCI_READ_CMD_6, 0x21);
+	octeon_npi_write32(CVMX_NPI_PCI_READ_CMD_C, 0x31);
+	octeon_npi_write32(CVMX_NPI_PCI_READ_CMD_E, 0x31);
+}
+
+
+/*
+ * Initialize the Octeon PCI controller
+ */
+static int __init octeon_pci_setup(void)
+{
+	union cvmx_npi_mem_access_subidx mem_access;
+	int index;
+
+	/* Only these chips have PCI */
+	if (octeon_has_feature(OCTEON_FEATURE_PCIE))
+		return 0;
+
+	if (!octeon_is_pci_host()) {
+		pr_notice("Not in host mode, PCI Controller not initialized\n");
+		return 0;
+	}
+
+	/* Point pcibios_map_irq() to the PCI version of it */
+	octeon_pcibios_map_irq = octeon_pci_pcibios_map_irq;
+
+	/* Only use the big bars on chips that support it */
+	if (OCTEON_IS_MODEL(OCTEON_CN31XX) ||
+	    OCTEON_IS_MODEL(OCTEON_CN38XX_PASS2) ||
+	    OCTEON_IS_MODEL(OCTEON_CN38XX_PASS1))
+		octeon_dma_bar_type = OCTEON_DMA_BAR_TYPE_SMALL;
+	else
+		octeon_dma_bar_type = OCTEON_DMA_BAR_TYPE_BIG;
+
+	/* PCI I/O and PCI MEM values */
+	set_io_port_base(OCTEON_PCI_IOSPACE_BASE);
+	ioport_resource.start = 0;
+	ioport_resource.end = OCTEON_PCI_IOSPACE_SIZE - 1;
+
+	pr_notice("%s Octeon big bar support\n",
+		  (octeon_dma_bar_type ==
+		  OCTEON_DMA_BAR_TYPE_BIG) ? "Enabling" : "Disabling");
+
+	octeon_pci_initialize();
+
+	mem_access.u64 = 0;
+	mem_access.s.esr = 1;	/* Endian-Swap on read. */
+	mem_access.s.esw = 1;	/* Endian-Swap on write. */
+	mem_access.s.nsr = 0;	/* No-Snoop on read. */
+	mem_access.s.nsw = 0;	/* No-Snoop on write. */
+	mem_access.s.ror = 0;	/* Relax Read on read. */
+	mem_access.s.row = 0;	/* Relax Order on write. */
+	mem_access.s.ba = 0;	/* PCI Address bits [63:36]. */
+	cvmx_write_csr(CVMX_NPI_MEM_ACCESS_SUBID3, mem_access.u64);
+
+	/*
+	 * Remap the Octeon BAR 2 above all 32 bit devices
+	 * (0x8000000000ul).  This is done here so it is remapped
+	 * before the readl()'s below. We don't want BAR2 overlapping
+	 * with BAR0/BAR1 during these reads.
+	 */
+	octeon_npi_write32(CVMX_NPI_PCI_CFG08,
+			   (u32)(OCTEON_BAR2_PCI_ADDRESS & 0xffffffffull));
+	octeon_npi_write32(CVMX_NPI_PCI_CFG09,
+			   (u32)(OCTEON_BAR2_PCI_ADDRESS >> 32));
+
+	if (octeon_dma_bar_type == OCTEON_DMA_BAR_TYPE_BIG) {
+		/* Remap the Octeon BAR 0 to 0-2GB */
+		octeon_npi_write32(CVMX_NPI_PCI_CFG04, 0);
+		octeon_npi_write32(CVMX_NPI_PCI_CFG05, 0);
+
+		/*
+		 * Remap the Octeon BAR 1 to map 2GB-4GB (minus the
+		 * BAR 1 hole).
+		 */
+		octeon_npi_write32(CVMX_NPI_PCI_CFG06, 2ul << 30);
+		octeon_npi_write32(CVMX_NPI_PCI_CFG07, 0);
+
+		/* BAR1 movable mappings set for identity mapping */
+		octeon_bar1_pci_phys = 0x80000000ull;
+		for (index = 0; index < 32; index++) {
+			union cvmx_pci_bar1_indexx bar1_index;
+
+			bar1_index.u32 = 0;
+			/* Address bits[35:22] sent to L2C */
+			bar1_index.s.addr_idx =
+				(octeon_bar1_pci_phys >> 22) + index;
+			/* Don't put PCI accesses in L2. */
+			bar1_index.s.ca = 1;
+			/* Endian Swap Mode */
+			bar1_index.s.end_swp = 1;
+			/* Set '1' when the selected address range is valid. */
+			bar1_index.s.addr_v = 1;
+			octeon_npi_write32(CVMX_NPI_PCI_BAR1_INDEXX(index),
+					   bar1_index.u32);
+		}
+
+		/* Devices go after BAR1 */
+		octeon_pci_mem_resource.start =
+			OCTEON_PCI_MEMSPACE_OFFSET + (4ul << 30) -
+			(OCTEON_PCI_BAR1_HOLE_SIZE << 20);
+		octeon_pci_mem_resource.end =
+			octeon_pci_mem_resource.start + (1ul << 30);
+	} else {
+		/* Remap the Octeon BAR 0 to map 128MB-(128MB+4KB) */
+		octeon_npi_write32(CVMX_NPI_PCI_CFG04, 128ul << 20);
+		octeon_npi_write32(CVMX_NPI_PCI_CFG05, 0);
+
+		/* Remap the Octeon BAR 1 to map 0-128MB */
+		octeon_npi_write32(CVMX_NPI_PCI_CFG06, 0);
+		octeon_npi_write32(CVMX_NPI_PCI_CFG07, 0);
+
+		/* BAR1 movable regions contiguous to cover the swiotlb */
+		octeon_bar1_pci_phys =
+			io_tlb_default_mem.start & ~((1ull << 22) - 1);
+
+		for (index = 0; index < 32; index++) {
+			union cvmx_pci_bar1_indexx bar1_index;
+
+			bar1_index.u32 = 0;
+			/* Address bits[35:22] sent to L2C */
+			bar1_index.s.addr_idx =
+				(octeon_bar1_pci_phys >> 22) + index;
+			/* Don't put PCI accesses in L2. */
+			bar1_index.s.ca = 1;
+			/* Endian Swap Mode */
+			bar1_index.s.end_swp = 1;
+			/* Set '1' when the selected address range is valid. */
+			bar1_index.s.addr_v = 1;
+			octeon_npi_write32(CVMX_NPI_PCI_BAR1_INDEXX(index),
+					   bar1_index.u32);
+		}
+
+		/* Devices go after BAR0 */
+		octeon_pci_mem_resource.start =
+			OCTEON_PCI_MEMSPACE_OFFSET + (128ul << 20) +
+			(4ul << 10);
+		octeon_pci_mem_resource.end =
+			octeon_pci_mem_resource.start + (1ul << 30);
+	}
+
+	register_pci_controller(&octeon_pci_controller);
+
+	/*
+	 * Clear any errors that might be pending from before the bus
+	 * was setup properly.
+	 */
+	cvmx_write_csr(CVMX_NPI_PCI_INT_SUM2, -1);
+
+	if (IS_ERR(platform_device_register_simple("octeon_pci_edac",
+						   -1, NULL, 0)))
+		pr_err("Registration of co_pci_edac failed!\n");
+
+	octeon_pci_dma_init();
+
+	return 0;
+}
+
+arch_initcall(octeon_pci_setup);
diff --git a/arch/mips/pci/pci-rc32434.c b/arch/mips/pci/pci-rc32434.c
new file mode 100644
index 000000000..7f6ce6d73
--- /dev/null
+++ b/arch/mips/pci/pci-rc32434.c
@@ -0,0 +1,231 @@
+/*
+ *  BRIEF MODULE DESCRIPTION
+ *     PCI initialization for IDT EB434 board
+ *
+ *  Copyright 2004 IDT Inc. (rischelp@idt.com)
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+
+#include <asm/mach-rc32434/rc32434.h>
+#include <asm/mach-rc32434/pci.h>
+
+#define PCI_ACCESS_READ	 0
+#define PCI_ACCESS_WRITE 1
+
+/* define an unsigned array for the PCI registers */
+static unsigned int korina_cnfg_regs[25] = {
+	KORINA_CNFG1, KORINA_CNFG2, KORINA_CNFG3, KORINA_CNFG4,
+	KORINA_CNFG5, KORINA_CNFG6, KORINA_CNFG7, KORINA_CNFG8,
+	KORINA_CNFG9, KORINA_CNFG10, KORINA_CNFG11, KORINA_CNFG12,
+	KORINA_CNFG13, KORINA_CNFG14, KORINA_CNFG15, KORINA_CNFG16,
+	KORINA_CNFG17, KORINA_CNFG18, KORINA_CNFG19, KORINA_CNFG20,
+	KORINA_CNFG21, KORINA_CNFG22, KORINA_CNFG23, KORINA_CNFG24
+};
+static struct resource rc32434_res_pci_mem1;
+static struct resource rc32434_res_pci_mem2;
+
+static struct resource rc32434_res_pci_mem1 = {
+	.name = "PCI MEM1",
+	.start = 0x50000000,
+	.end = 0x5FFFFFFF,
+	.flags = IORESOURCE_MEM,
+	.sibling = NULL,
+	.child = &rc32434_res_pci_mem2
+};
+
+static struct resource rc32434_res_pci_mem2 = {
+	.name = "PCI Mem2",
+	.start = 0x60000000,
+	.end = 0x6FFFFFFF,
+	.flags = IORESOURCE_MEM,
+	.parent = &rc32434_res_pci_mem1,
+	.sibling = NULL,
+	.child = NULL
+};
+
+static struct resource rc32434_res_pci_io1 = {
+	.name = "PCI I/O1",
+	.start = 0x18800000,
+	.end = 0x188FFFFF,
+	.flags = IORESOURCE_IO,
+};
+
+extern struct pci_ops rc32434_pci_ops;
+
+#define PCI_MEM1_START	PCI_ADDR_START
+#define PCI_MEM1_END	(PCI_ADDR_START + CPUTOPCI_MEM_WIN - 1)
+#define PCI_MEM2_START	(PCI_ADDR_START + CPUTOPCI_MEM_WIN)
+#define PCI_MEM2_END	(PCI_ADDR_START + (2 * CPUTOPCI_MEM_WIN)  - 1)
+#define PCI_IO1_START	(PCI_ADDR_START + (2 * CPUTOPCI_MEM_WIN))
+#define PCI_IO1_END							\
+	(PCI_ADDR_START + (2 * CPUTOPCI_MEM_WIN) + CPUTOPCI_IO_WIN - 1)
+#define PCI_IO2_START							\
+	(PCI_ADDR_START + (2 * CPUTOPCI_MEM_WIN) + CPUTOPCI_IO_WIN)
+#define PCI_IO2_END							\
+	(PCI_ADDR_START + (2 * CPUTOPCI_MEM_WIN) + (2 * CPUTOPCI_IO_WIN) - 1)
+
+struct pci_controller rc32434_controller2;
+
+struct pci_controller rc32434_controller = {
+	.pci_ops = &rc32434_pci_ops,
+	.mem_resource = &rc32434_res_pci_mem1,
+	.io_resource = &rc32434_res_pci_io1,
+	.mem_offset = 0,
+	.io_offset = 0,
+
+};
+
+#ifdef __MIPSEB__
+#define PCI_ENDIAN_FLAG PCILBAC_sb_m
+#else
+#define PCI_ENDIAN_FLAG 0
+#endif
+
+static int __init rc32434_pcibridge_init(void)
+{
+	unsigned int pcicvalue, pcicdata = 0;
+	unsigned int dummyread, pcicntlval;
+	int loopCount;
+	unsigned int pci_config_addr;
+
+	pcicvalue = rc32434_pci->pcic;
+	pcicvalue = (pcicvalue >> PCIM_SHFT) & PCIM_BIT_LEN;
+	if (!((pcicvalue == PCIM_H_EA) ||
+	      (pcicvalue == PCIM_H_IA_FIX) ||
+	      (pcicvalue == PCIM_H_IA_RR))) {
+		pr_err("PCI init error!!!\n");
+		/* Not in Host Mode, return ERROR */
+		return -1;
+	}
+	/* Enables the Idle Grant mode, Arbiter Parking */
+	pcicdata |= (PCI_CTL_IGM | PCI_CTL_EAP | PCI_CTL_EN);
+	rc32434_pci->pcic = pcicdata;	/* Enable the PCI bus Interface */
+	/* Zero out the PCI status & PCI Status Mask */
+	for (;;) {
+		pcicdata = rc32434_pci->pcis;
+		if (!(pcicdata & PCI_STAT_RIP))
+			break;
+	}
+
+	rc32434_pci->pcis = 0;
+	rc32434_pci->pcism = 0xFFFFFFFF;
+	/* Zero out the PCI decoupled registers */
+	rc32434_pci->pcidac = 0;	/*
+					 * disable PCI decoupled accesses at
+					 * initialization
+					 */
+	rc32434_pci->pcidas = 0;	/* clear the status */
+	rc32434_pci->pcidasm = 0x0000007F;	/* Mask all the interrupts */
+	/* Mask PCI Messaging Interrupts */
+	rc32434_pci_msg->pciiic = 0;
+	rc32434_pci_msg->pciiim = 0xFFFFFFFF;
+	rc32434_pci_msg->pciioic = 0;
+	rc32434_pci_msg->pciioim = 0;
+
+
+	/* Setup PCILB0 as Memory Window */
+	rc32434_pci->pcilba[0].address = (unsigned int) (PCI_ADDR_START);
+
+	/* setup the PCI map address as same as the local address */
+
+	rc32434_pci->pcilba[0].mapping = (unsigned int) (PCI_ADDR_START);
+
+
+	/* Setup PCILBA1 as MEM */
+	rc32434_pci->pcilba[0].control =
+	    (((SIZE_256MB & 0x1f) << PCI_LBAC_SIZE_BIT) | PCI_ENDIAN_FLAG);
+	dummyread = rc32434_pci->pcilba[0].control;	/* flush the CPU write Buffers */
+	rc32434_pci->pcilba[1].address = 0x60000000;
+	rc32434_pci->pcilba[1].mapping = 0x60000000;
+
+	/* setup PCILBA2 as IO Window */
+	rc32434_pci->pcilba[1].control =
+	    (((SIZE_256MB & 0x1f) << PCI_LBAC_SIZE_BIT) | PCI_ENDIAN_FLAG);
+	dummyread = rc32434_pci->pcilba[1].control;	/* flush the CPU write Buffers */
+	rc32434_pci->pcilba[2].address = 0x18C00000;
+	rc32434_pci->pcilba[2].mapping = 0x18FFFFFF;
+
+	/* setup PCILBA2 as IO Window */
+	rc32434_pci->pcilba[2].control =
+	    (((SIZE_4MB & 0x1f) << PCI_LBAC_SIZE_BIT) | PCI_ENDIAN_FLAG);
+	dummyread = rc32434_pci->pcilba[2].control;	/* flush the CPU write Buffers */
+
+	/* Setup PCILBA3 as IO Window */
+	rc32434_pci->pcilba[3].address = 0x18800000;
+	rc32434_pci->pcilba[3].mapping = 0x18800000;
+	rc32434_pci->pcilba[3].control =
+	    ((((SIZE_1MB & 0x1ff) << PCI_LBAC_SIZE_BIT) | PCI_LBAC_MSI) |
+	     PCI_ENDIAN_FLAG);
+	dummyread = rc32434_pci->pcilba[3].control;	/* flush the CPU write Buffers */
+
+	pci_config_addr = (unsigned int) (0x80000004);
+	for (loopCount = 0; loopCount < 24; loopCount++) {
+		rc32434_pci->pcicfga = pci_config_addr;
+		dummyread = rc32434_pci->pcicfga;
+		rc32434_pci->pcicfgd = korina_cnfg_regs[loopCount];
+		dummyread = rc32434_pci->pcicfgd;
+		pci_config_addr += 4;
+	}
+	rc32434_pci->pcitc =
+	    (unsigned int) ((PCITC_RTIMER_VAL & 0xff) << PCI_TC_RTIMER_BIT) |
+	    ((PCITC_DTIMER_VAL & 0xff) << PCI_TC_DTIMER_BIT);
+
+	pcicntlval = rc32434_pci->pcic;
+	pcicntlval &= ~PCI_CTL_TNR;
+	rc32434_pci->pcic = pcicntlval;
+	pcicntlval = rc32434_pci->pcic;
+
+	return 0;
+}
+
+static int __init rc32434_pci_init(void)
+{
+	void __iomem *io_map_base;
+
+	pr_info("PCI: Initializing PCI\n");
+
+	ioport_resource.start = rc32434_res_pci_io1.start;
+	ioport_resource.end = rc32434_res_pci_io1.end;
+
+	rc32434_pcibridge_init();
+
+	io_map_base = ioremap(rc32434_res_pci_io1.start,
+			      resource_size(&rc32434_res_pci_io1));
+
+	if (!io_map_base)
+		return -ENOMEM;
+
+	rc32434_controller.io_map_base =
+		(unsigned long)io_map_base - rc32434_res_pci_io1.start;
+
+	register_pci_controller(&rc32434_controller);
+	rc32434_sync();
+
+	return 0;
+}
+
+arch_initcall(rc32434_pci_init);
diff --git a/arch/mips/pci/pci-rt2880.c b/arch/mips/pci/pci-rt2880.c
new file mode 100644
index 000000000..e9dd01431
--- /dev/null
+++ b/arch/mips/pci/pci-rt2880.c
@@ -0,0 +1,278 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *  Ralink RT288x SoC PCI register definitions
+ *
+ *  Copyright (C) 2009 John Crispin <john@phrozen.org>
+ *  Copyright (C) 2009 Gabor Juhos <juhosg@openwrt.org>
+ *
+ *  Parts of this file are based on Ralink's 2.6.21 BSP
+ */
+
+#include <linux/delay.h>
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/io.h>
+#include <linux/init.h>
+#include <linux/of_platform.h>
+#include <linux/of_irq.h>
+#include <linux/of_pci.h>
+
+#include <asm/mach-ralink/rt288x.h>
+
+#define RT2880_PCI_BASE		0x00440000
+#define RT288X_CPU_IRQ_PCI	4
+
+#define RT2880_PCI_MEM_BASE	0x20000000
+#define RT2880_PCI_MEM_SIZE	0x10000000
+#define RT2880_PCI_IO_BASE	0x00460000
+#define RT2880_PCI_IO_SIZE	0x00010000
+
+#define RT2880_PCI_REG_PCICFG_ADDR	0x00
+#define RT2880_PCI_REG_PCIMSK_ADDR	0x0c
+#define RT2880_PCI_REG_BAR0SETUP_ADDR	0x10
+#define RT2880_PCI_REG_IMBASEBAR0_ADDR	0x18
+#define RT2880_PCI_REG_CONFIG_ADDR	0x20
+#define RT2880_PCI_REG_CONFIG_DATA	0x24
+#define RT2880_PCI_REG_MEMBASE		0x28
+#define RT2880_PCI_REG_IOBASE		0x2c
+#define RT2880_PCI_REG_ID		0x30
+#define RT2880_PCI_REG_CLASS		0x34
+#define RT2880_PCI_REG_SUBID		0x38
+#define RT2880_PCI_REG_ARBCTL		0x80
+
+static void __iomem *rt2880_pci_base;
+
+static u32 rt2880_pci_reg_read(u32 reg)
+{
+	return readl(rt2880_pci_base + reg);
+}
+
+static void rt2880_pci_reg_write(u32 val, u32 reg)
+{
+	writel(val, rt2880_pci_base + reg);
+}
+
+static inline u32 rt2880_pci_get_cfgaddr(unsigned int bus, unsigned int slot,
+					 unsigned int func, unsigned int where)
+{
+	return ((bus << 16) | (slot << 11) | (func << 8) | (where & 0xfc) |
+		0x80000000);
+}
+
+static int rt2880_pci_config_read(struct pci_bus *bus, unsigned int devfn,
+				  int where, int size, u32 *val)
+{
+	u32 address;
+	u32 data;
+
+	address = rt2880_pci_get_cfgaddr(bus->number, PCI_SLOT(devfn),
+					 PCI_FUNC(devfn), where);
+
+	rt2880_pci_reg_write(address, RT2880_PCI_REG_CONFIG_ADDR);
+	data = rt2880_pci_reg_read(RT2880_PCI_REG_CONFIG_DATA);
+
+	switch (size) {
+	case 1:
+		*val = (data >> ((where & 3) << 3)) & 0xff;
+		break;
+	case 2:
+		*val = (data >> ((where & 3) << 3)) & 0xffff;
+		break;
+	case 4:
+		*val = data;
+		break;
+	}
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int rt2880_pci_config_write(struct pci_bus *bus, unsigned int devfn,
+				   int where, int size, u32 val)
+{
+	u32 address;
+	u32 data;
+
+	address = rt2880_pci_get_cfgaddr(bus->number, PCI_SLOT(devfn),
+					 PCI_FUNC(devfn), where);
+
+	rt2880_pci_reg_write(address, RT2880_PCI_REG_CONFIG_ADDR);
+	data = rt2880_pci_reg_read(RT2880_PCI_REG_CONFIG_DATA);
+
+	switch (size) {
+	case 1:
+		data = (data & ~(0xff << ((where & 3) << 3))) |
+		       (val << ((where & 3) << 3));
+		break;
+	case 2:
+		data = (data & ~(0xffff << ((where & 3) << 3))) |
+		       (val << ((where & 3) << 3));
+		break;
+	case 4:
+		data = val;
+		break;
+	}
+
+	rt2880_pci_reg_write(data, RT2880_PCI_REG_CONFIG_DATA);
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static struct pci_ops rt2880_pci_ops = {
+	.read	= rt2880_pci_config_read,
+	.write	= rt2880_pci_config_write,
+};
+
+static struct resource rt2880_pci_mem_resource = {
+	.name	= "PCI MEM space",
+	.start	= RT2880_PCI_MEM_BASE,
+	.end	= RT2880_PCI_MEM_BASE + RT2880_PCI_MEM_SIZE - 1,
+	.flags	= IORESOURCE_MEM,
+};
+
+static struct resource rt2880_pci_io_resource = {
+	.name	= "PCI IO space",
+	.start	= RT2880_PCI_IO_BASE,
+	.end	= RT2880_PCI_IO_BASE + RT2880_PCI_IO_SIZE - 1,
+	.flags	= IORESOURCE_IO,
+};
+
+static struct pci_controller rt2880_pci_controller = {
+	.pci_ops	= &rt2880_pci_ops,
+	.mem_resource	= &rt2880_pci_mem_resource,
+	.io_resource	= &rt2880_pci_io_resource,
+};
+
+static inline u32 rt2880_pci_read_u32(unsigned long reg)
+{
+	u32 address;
+	u32 ret;
+
+	address = rt2880_pci_get_cfgaddr(0, 0, 0, reg);
+
+	rt2880_pci_reg_write(address, RT2880_PCI_REG_CONFIG_ADDR);
+	ret = rt2880_pci_reg_read(RT2880_PCI_REG_CONFIG_DATA);
+
+	return ret;
+}
+
+static inline void rt2880_pci_write_u32(unsigned long reg, u32 val)
+{
+	u32 address;
+
+	address = rt2880_pci_get_cfgaddr(0, 0, 0, reg);
+
+	rt2880_pci_reg_write(address, RT2880_PCI_REG_CONFIG_ADDR);
+	rt2880_pci_reg_write(val, RT2880_PCI_REG_CONFIG_DATA);
+}
+
+int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	int irq = -1;
+
+	if (dev->bus->number != 0)
+		return irq;
+
+	switch (PCI_SLOT(dev->devfn)) {
+	case 0x00:
+		break;
+	case 0x11:
+		irq = RT288X_CPU_IRQ_PCI;
+		break;
+	default:
+		pr_err("%s:%s[%d] trying to alloc unknown pci irq\n",
+		       __FILE__, __func__, __LINE__);
+		BUG();
+		break;
+	}
+
+	return irq;
+}
+
+static int rt288x_pci_probe(struct platform_device *pdev)
+{
+	void __iomem *io_map_base;
+
+	rt2880_pci_base = ioremap(RT2880_PCI_BASE, PAGE_SIZE);
+
+	io_map_base = ioremap(RT2880_PCI_IO_BASE, RT2880_PCI_IO_SIZE);
+	rt2880_pci_controller.io_map_base = (unsigned long) io_map_base;
+	set_io_port_base((unsigned long) io_map_base);
+
+	ioport_resource.start = RT2880_PCI_IO_BASE;
+	ioport_resource.end = RT2880_PCI_IO_BASE + RT2880_PCI_IO_SIZE - 1;
+
+	rt2880_pci_reg_write(0, RT2880_PCI_REG_PCICFG_ADDR);
+	udelay(1);
+
+	rt2880_pci_reg_write(0x79, RT2880_PCI_REG_ARBCTL);
+	rt2880_pci_reg_write(0x07FF0001, RT2880_PCI_REG_BAR0SETUP_ADDR);
+	rt2880_pci_reg_write(RT2880_PCI_MEM_BASE, RT2880_PCI_REG_MEMBASE);
+	rt2880_pci_reg_write(RT2880_PCI_IO_BASE, RT2880_PCI_REG_IOBASE);
+	rt2880_pci_reg_write(0x08000000, RT2880_PCI_REG_IMBASEBAR0_ADDR);
+	rt2880_pci_reg_write(0x08021814, RT2880_PCI_REG_ID);
+	rt2880_pci_reg_write(0x00800001, RT2880_PCI_REG_CLASS);
+	rt2880_pci_reg_write(0x28801814, RT2880_PCI_REG_SUBID);
+	rt2880_pci_reg_write(0x000c0000, RT2880_PCI_REG_PCIMSK_ADDR);
+
+	rt2880_pci_write_u32(PCI_BASE_ADDRESS_0, 0x08000000);
+	(void) rt2880_pci_read_u32(PCI_BASE_ADDRESS_0);
+
+	rt2880_pci_controller.of_node = pdev->dev.of_node;
+
+	register_pci_controller(&rt2880_pci_controller);
+	return 0;
+}
+
+int pcibios_plat_dev_init(struct pci_dev *dev)
+{
+	static bool slot0_init;
+
+	/*
+	 * Nobody seems to initialize slot 0, but this platform requires it, so
+	 * do it once when some other slot is being enabled. The PCI subsystem
+	 * should configure other slots properly, so no need to do anything
+	 * special for those.
+	 */
+	if (!slot0_init && dev->bus->number == 0) {
+		u16 cmd;
+		u32 bar0;
+
+		slot0_init = true;
+
+		pci_bus_write_config_dword(dev->bus, 0, PCI_BASE_ADDRESS_0,
+					   0x08000000);
+		pci_bus_read_config_dword(dev->bus, 0, PCI_BASE_ADDRESS_0,
+					  &bar0);
+
+		pci_bus_read_config_word(dev->bus, 0, PCI_COMMAND, &cmd);
+		cmd |= PCI_COMMAND_MASTER | PCI_COMMAND_IO | PCI_COMMAND_MEMORY;
+		pci_bus_write_config_word(dev->bus, 0, PCI_COMMAND, cmd);
+	}
+
+	return 0;
+}
+
+static const struct of_device_id rt288x_pci_match[] = {
+	{ .compatible = "ralink,rt288x-pci" },
+	{},
+};
+
+static struct platform_driver rt288x_pci_driver = {
+	.probe = rt288x_pci_probe,
+	.driver = {
+		.name = "rt288x-pci",
+		.of_match_table = rt288x_pci_match,
+	},
+};
+
+int __init pcibios_init(void)
+{
+	int ret = platform_driver_register(&rt288x_pci_driver);
+
+	if (ret)
+		pr_info("rt288x-pci: Error registering platform driver!");
+
+	return ret;
+}
+
+arch_initcall(pcibios_init);
diff --git a/arch/mips/pci/pci-rt3883.c b/arch/mips/pci/pci-rt3883.c
new file mode 100644
index 000000000..e07ae098b
--- /dev/null
+++ b/arch/mips/pci/pci-rt3883.c
@@ -0,0 +1,582 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *  Ralink RT3662/RT3883 SoC PCI support
+ *
+ *  Copyright (C) 2011-2013 Gabor Juhos <juhosg@openwrt.org>
+ *
+ *  Parts of this file are based on Ralink's 2.6.21 BSP
+ */
+
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/io.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/irqdomain.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_pci.h>
+#include <linux/platform_device.h>
+
+#include <asm/mach-ralink/rt3883.h>
+#include <asm/mach-ralink/ralink_regs.h>
+
+#define RT3883_MEMORY_BASE		0x00000000
+#define RT3883_MEMORY_SIZE		0x02000000
+
+#define RT3883_PCI_REG_PCICFG		0x00
+#define   RT3883_PCICFG_P2P_BR_DEVNUM_M 0xf
+#define   RT3883_PCICFG_P2P_BR_DEVNUM_S 16
+#define   RT3883_PCICFG_PCIRST		BIT(1)
+#define RT3883_PCI_REG_PCIRAW		0x04
+#define RT3883_PCI_REG_PCIINT		0x08
+#define RT3883_PCI_REG_PCIENA		0x0c
+
+#define RT3883_PCI_REG_CFGADDR		0x20
+#define RT3883_PCI_REG_CFGDATA		0x24
+#define RT3883_PCI_REG_MEMBASE		0x28
+#define RT3883_PCI_REG_IOBASE		0x2c
+#define RT3883_PCI_REG_ARBCTL		0x80
+
+#define RT3883_PCI_REG_BASE(_x)		(0x1000 + (_x) * 0x1000)
+#define RT3883_PCI_REG_BAR0SETUP(_x)	(RT3883_PCI_REG_BASE((_x)) + 0x10)
+#define RT3883_PCI_REG_IMBASEBAR0(_x)	(RT3883_PCI_REG_BASE((_x)) + 0x18)
+#define RT3883_PCI_REG_ID(_x)		(RT3883_PCI_REG_BASE((_x)) + 0x30)
+#define RT3883_PCI_REG_CLASS(_x)	(RT3883_PCI_REG_BASE((_x)) + 0x34)
+#define RT3883_PCI_REG_SUBID(_x)	(RT3883_PCI_REG_BASE((_x)) + 0x38)
+#define RT3883_PCI_REG_STATUS(_x)	(RT3883_PCI_REG_BASE((_x)) + 0x50)
+
+#define RT3883_PCI_MODE_NONE	0
+#define RT3883_PCI_MODE_PCI	BIT(0)
+#define RT3883_PCI_MODE_PCIE	BIT(1)
+#define RT3883_PCI_MODE_BOTH	(RT3883_PCI_MODE_PCI | RT3883_PCI_MODE_PCIE)
+
+#define RT3883_PCI_IRQ_COUNT	32
+
+#define RT3883_P2P_BR_DEVNUM	1
+
+struct rt3883_pci_controller {
+	void __iomem *base;
+
+	struct device_node *intc_of_node;
+	struct irq_domain *irq_domain;
+
+	struct pci_controller pci_controller;
+	struct resource io_res;
+	struct resource mem_res;
+
+	bool pcie_ready;
+};
+
+static inline struct rt3883_pci_controller *
+pci_bus_to_rt3883_controller(struct pci_bus *bus)
+{
+	struct pci_controller *hose;
+
+	hose = (struct pci_controller *) bus->sysdata;
+	return container_of(hose, struct rt3883_pci_controller, pci_controller);
+}
+
+static inline u32 rt3883_pci_r32(struct rt3883_pci_controller *rpc,
+				 unsigned reg)
+{
+	return ioread32(rpc->base + reg);
+}
+
+static inline void rt3883_pci_w32(struct rt3883_pci_controller *rpc,
+				  u32 val, unsigned reg)
+{
+	iowrite32(val, rpc->base + reg);
+}
+
+static inline u32 rt3883_pci_get_cfgaddr(unsigned int bus, unsigned int slot,
+					 unsigned int func, unsigned int where)
+{
+	return (bus << 16) | (slot << 11) | (func << 8) | (where & 0xfc) |
+	       0x80000000;
+}
+
+static u32 rt3883_pci_read_cfg32(struct rt3883_pci_controller *rpc,
+			       unsigned bus, unsigned slot,
+			       unsigned func, unsigned reg)
+{
+	u32 address;
+
+	address = rt3883_pci_get_cfgaddr(bus, slot, func, reg);
+
+	rt3883_pci_w32(rpc, address, RT3883_PCI_REG_CFGADDR);
+
+	return rt3883_pci_r32(rpc, RT3883_PCI_REG_CFGDATA);
+}
+
+static void rt3883_pci_write_cfg32(struct rt3883_pci_controller *rpc,
+				 unsigned bus, unsigned slot,
+				 unsigned func, unsigned reg, u32 val)
+{
+	u32 address;
+
+	address = rt3883_pci_get_cfgaddr(bus, slot, func, reg);
+
+	rt3883_pci_w32(rpc, address, RT3883_PCI_REG_CFGADDR);
+	rt3883_pci_w32(rpc, val, RT3883_PCI_REG_CFGDATA);
+}
+
+static void rt3883_pci_irq_handler(struct irq_desc *desc)
+{
+	struct rt3883_pci_controller *rpc;
+	u32 pending;
+
+	rpc = irq_desc_get_handler_data(desc);
+
+	pending = rt3883_pci_r32(rpc, RT3883_PCI_REG_PCIINT) &
+		  rt3883_pci_r32(rpc, RT3883_PCI_REG_PCIENA);
+
+	if (!pending) {
+		spurious_interrupt();
+		return;
+	}
+
+	while (pending) {
+		unsigned bit = __ffs(pending);
+
+		generic_handle_domain_irq(rpc->irq_domain, bit);
+
+		pending &= ~BIT(bit);
+	}
+}
+
+static void rt3883_pci_irq_unmask(struct irq_data *d)
+{
+	struct rt3883_pci_controller *rpc;
+	u32 t;
+
+	rpc = irq_data_get_irq_chip_data(d);
+
+	t = rt3883_pci_r32(rpc, RT3883_PCI_REG_PCIENA);
+	rt3883_pci_w32(rpc, t | BIT(d->hwirq), RT3883_PCI_REG_PCIENA);
+	/* flush write */
+	rt3883_pci_r32(rpc, RT3883_PCI_REG_PCIENA);
+}
+
+static void rt3883_pci_irq_mask(struct irq_data *d)
+{
+	struct rt3883_pci_controller *rpc;
+	u32 t;
+
+	rpc = irq_data_get_irq_chip_data(d);
+
+	t = rt3883_pci_r32(rpc, RT3883_PCI_REG_PCIENA);
+	rt3883_pci_w32(rpc, t & ~BIT(d->hwirq), RT3883_PCI_REG_PCIENA);
+	/* flush write */
+	rt3883_pci_r32(rpc, RT3883_PCI_REG_PCIENA);
+}
+
+static struct irq_chip rt3883_pci_irq_chip = {
+	.name		= "RT3883 PCI",
+	.irq_mask	= rt3883_pci_irq_mask,
+	.irq_unmask	= rt3883_pci_irq_unmask,
+	.irq_mask_ack	= rt3883_pci_irq_mask,
+};
+
+static int rt3883_pci_irq_map(struct irq_domain *d, unsigned int irq,
+			      irq_hw_number_t hw)
+{
+	irq_set_chip_and_handler(irq, &rt3883_pci_irq_chip, handle_level_irq);
+	irq_set_chip_data(irq, d->host_data);
+
+	return 0;
+}
+
+static const struct irq_domain_ops rt3883_pci_irq_domain_ops = {
+	.map = rt3883_pci_irq_map,
+	.xlate = irq_domain_xlate_onecell,
+};
+
+static int rt3883_pci_irq_init(struct device *dev,
+			       struct rt3883_pci_controller *rpc)
+{
+	int irq;
+
+	irq = irq_of_parse_and_map(rpc->intc_of_node, 0);
+	if (irq == 0) {
+		dev_err(dev, "%pOF has no IRQ", rpc->intc_of_node);
+		return -EINVAL;
+	}
+
+	/* disable all interrupts */
+	rt3883_pci_w32(rpc, 0, RT3883_PCI_REG_PCIENA);
+
+	rpc->irq_domain =
+		irq_domain_add_linear(rpc->intc_of_node, RT3883_PCI_IRQ_COUNT,
+				      &rt3883_pci_irq_domain_ops,
+				      rpc);
+	if (!rpc->irq_domain) {
+		dev_err(dev, "unable to add IRQ domain\n");
+		return -ENODEV;
+	}
+
+	irq_set_chained_handler_and_data(irq, rt3883_pci_irq_handler, rpc);
+
+	return 0;
+}
+
+static int rt3883_pci_config_read(struct pci_bus *bus, unsigned int devfn,
+				  int where, int size, u32 *val)
+{
+	struct rt3883_pci_controller *rpc;
+	u32 address;
+	u32 data;
+
+	rpc = pci_bus_to_rt3883_controller(bus);
+
+	if (!rpc->pcie_ready && bus->number == 1)
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	address = rt3883_pci_get_cfgaddr(bus->number, PCI_SLOT(devfn),
+					 PCI_FUNC(devfn), where);
+
+	rt3883_pci_w32(rpc, address, RT3883_PCI_REG_CFGADDR);
+	data = rt3883_pci_r32(rpc, RT3883_PCI_REG_CFGDATA);
+
+	switch (size) {
+	case 1:
+		*val = (data >> ((where & 3) << 3)) & 0xff;
+		break;
+	case 2:
+		*val = (data >> ((where & 3) << 3)) & 0xffff;
+		break;
+	case 4:
+		*val = data;
+		break;
+	}
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int rt3883_pci_config_write(struct pci_bus *bus, unsigned int devfn,
+				   int where, int size, u32 val)
+{
+	struct rt3883_pci_controller *rpc;
+	u32 address;
+	u32 data;
+
+	rpc = pci_bus_to_rt3883_controller(bus);
+
+	if (!rpc->pcie_ready && bus->number == 1)
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	address = rt3883_pci_get_cfgaddr(bus->number, PCI_SLOT(devfn),
+					 PCI_FUNC(devfn), where);
+
+	rt3883_pci_w32(rpc, address, RT3883_PCI_REG_CFGADDR);
+	data = rt3883_pci_r32(rpc, RT3883_PCI_REG_CFGDATA);
+
+	switch (size) {
+	case 1:
+		data = (data & ~(0xff << ((where & 3) << 3))) |
+		       (val << ((where & 3) << 3));
+		break;
+	case 2:
+		data = (data & ~(0xffff << ((where & 3) << 3))) |
+		       (val << ((where & 3) << 3));
+		break;
+	case 4:
+		data = val;
+		break;
+	}
+
+	rt3883_pci_w32(rpc, data, RT3883_PCI_REG_CFGDATA);
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static struct pci_ops rt3883_pci_ops = {
+	.read	= rt3883_pci_config_read,
+	.write	= rt3883_pci_config_write,
+};
+
+static void rt3883_pci_preinit(struct rt3883_pci_controller *rpc, unsigned mode)
+{
+	u32 syscfg1;
+	u32 rstctrl;
+	u32 clkcfg1;
+	u32 t;
+
+	rstctrl = rt_sysc_r32(RT3883_SYSC_REG_RSTCTRL);
+	syscfg1 = rt_sysc_r32(RT3883_SYSC_REG_SYSCFG1);
+	clkcfg1 = rt_sysc_r32(RT3883_SYSC_REG_CLKCFG1);
+
+	if (mode & RT3883_PCI_MODE_PCIE) {
+		rstctrl |= RT3883_RSTCTRL_PCIE;
+		rt_sysc_w32(rstctrl, RT3883_SYSC_REG_RSTCTRL);
+
+		/* setup PCI PAD drive mode */
+		syscfg1 &= ~(0x30);
+		syscfg1 |= (2 << 4);
+		rt_sysc_w32(syscfg1, RT3883_SYSC_REG_SYSCFG1);
+
+		t = rt_sysc_r32(RT3883_SYSC_REG_PCIE_CLK_GEN0);
+		t &= ~BIT(31);
+		rt_sysc_w32(t, RT3883_SYSC_REG_PCIE_CLK_GEN0);
+
+		t = rt_sysc_r32(RT3883_SYSC_REG_PCIE_CLK_GEN1);
+		t &= 0x80ffffff;
+		rt_sysc_w32(t, RT3883_SYSC_REG_PCIE_CLK_GEN1);
+
+		t = rt_sysc_r32(RT3883_SYSC_REG_PCIE_CLK_GEN1);
+		t |= 0xa << 24;
+		rt_sysc_w32(t, RT3883_SYSC_REG_PCIE_CLK_GEN1);
+
+		t = rt_sysc_r32(RT3883_SYSC_REG_PCIE_CLK_GEN0);
+		t |= BIT(31);
+		rt_sysc_w32(t, RT3883_SYSC_REG_PCIE_CLK_GEN0);
+
+		msleep(50);
+
+		rstctrl &= ~RT3883_RSTCTRL_PCIE;
+		rt_sysc_w32(rstctrl, RT3883_SYSC_REG_RSTCTRL);
+	}
+
+	syscfg1 |= (RT3883_SYSCFG1_PCIE_RC_MODE | RT3883_SYSCFG1_PCI_HOST_MODE);
+
+	clkcfg1 &= ~(RT3883_CLKCFG1_PCI_CLK_EN | RT3883_CLKCFG1_PCIE_CLK_EN);
+
+	if (mode & RT3883_PCI_MODE_PCI) {
+		clkcfg1 |= RT3883_CLKCFG1_PCI_CLK_EN;
+		rstctrl &= ~RT3883_RSTCTRL_PCI;
+	}
+
+	if (mode & RT3883_PCI_MODE_PCIE) {
+		clkcfg1 |= RT3883_CLKCFG1_PCIE_CLK_EN;
+		rstctrl &= ~RT3883_RSTCTRL_PCIE;
+	}
+
+	rt_sysc_w32(syscfg1, RT3883_SYSC_REG_SYSCFG1);
+	rt_sysc_w32(rstctrl, RT3883_SYSC_REG_RSTCTRL);
+	rt_sysc_w32(clkcfg1, RT3883_SYSC_REG_CLKCFG1);
+
+	msleep(500);
+
+	/*
+	 * setup the device number of the P2P bridge
+	 * and de-assert the reset line
+	 */
+	t = (RT3883_P2P_BR_DEVNUM << RT3883_PCICFG_P2P_BR_DEVNUM_S);
+	rt3883_pci_w32(rpc, t, RT3883_PCI_REG_PCICFG);
+
+	/* flush write */
+	rt3883_pci_r32(rpc, RT3883_PCI_REG_PCICFG);
+	msleep(500);
+
+	if (mode & RT3883_PCI_MODE_PCIE) {
+		msleep(500);
+
+		t = rt3883_pci_r32(rpc, RT3883_PCI_REG_STATUS(1));
+
+		rpc->pcie_ready = t & BIT(0);
+
+		if (!rpc->pcie_ready) {
+			/* reset the PCIe block */
+			t = rt_sysc_r32(RT3883_SYSC_REG_RSTCTRL);
+			t |= RT3883_RSTCTRL_PCIE;
+			rt_sysc_w32(t, RT3883_SYSC_REG_RSTCTRL);
+			t &= ~RT3883_RSTCTRL_PCIE;
+			rt_sysc_w32(t, RT3883_SYSC_REG_RSTCTRL);
+
+			/* turn off PCIe clock */
+			t = rt_sysc_r32(RT3883_SYSC_REG_CLKCFG1);
+			t &= ~RT3883_CLKCFG1_PCIE_CLK_EN;
+			rt_sysc_w32(t, RT3883_SYSC_REG_CLKCFG1);
+
+			t = rt_sysc_r32(RT3883_SYSC_REG_PCIE_CLK_GEN0);
+			t &= ~0xf000c080;
+			rt_sysc_w32(t, RT3883_SYSC_REG_PCIE_CLK_GEN0);
+		}
+	}
+
+	/* enable PCI arbiter */
+	rt3883_pci_w32(rpc, 0x79, RT3883_PCI_REG_ARBCTL);
+}
+
+static int rt3883_pci_probe(struct platform_device *pdev)
+{
+	struct rt3883_pci_controller *rpc;
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct resource *res;
+	struct device_node *child;
+	u32 val;
+	int err;
+	int mode;
+
+	rpc = devm_kzalloc(dev, sizeof(*rpc), GFP_KERNEL);
+	if (!rpc)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	rpc->base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(rpc->base))
+		return PTR_ERR(rpc->base);
+
+	/* find the interrupt controller child node */
+	for_each_child_of_node(np, child) {
+		if (of_get_property(child, "interrupt-controller", NULL)) {
+			rpc->intc_of_node = child;
+			break;
+		}
+	}
+
+	if (!rpc->intc_of_node) {
+		dev_err(dev, "%pOF has no %s child node",
+			np, "interrupt controller");
+		return -EINVAL;
+	}
+
+	/* find the PCI host bridge child node */
+	for_each_child_of_node(np, child) {
+		if (of_node_is_type(child, "pci")) {
+			rpc->pci_controller.of_node = child;
+			break;
+		}
+	}
+
+	if (!rpc->pci_controller.of_node) {
+		dev_err(dev, "%pOF has no %s child node",
+			np, "PCI host bridge");
+		err = -EINVAL;
+		goto err_put_intc_node;
+	}
+
+	mode = RT3883_PCI_MODE_NONE;
+	for_each_available_child_of_node(rpc->pci_controller.of_node, child) {
+		int devfn;
+
+		if (!of_node_is_type(child, "pci"))
+			continue;
+
+		devfn = of_pci_get_devfn(child);
+		if (devfn < 0)
+			continue;
+
+		switch (PCI_SLOT(devfn)) {
+		case 1:
+			mode |= RT3883_PCI_MODE_PCIE;
+			break;
+
+		case 17:
+		case 18:
+			mode |= RT3883_PCI_MODE_PCI;
+			break;
+		}
+	}
+
+	if (mode == RT3883_PCI_MODE_NONE) {
+		dev_err(dev, "unable to determine PCI mode\n");
+		err = -EINVAL;
+		goto err_put_hb_node;
+	}
+
+	dev_info(dev, "mode:%s%s\n",
+		 (mode & RT3883_PCI_MODE_PCI) ? " PCI" : "",
+		 (mode & RT3883_PCI_MODE_PCIE) ? " PCIe" : "");
+
+	rt3883_pci_preinit(rpc, mode);
+
+	rpc->pci_controller.pci_ops = &rt3883_pci_ops;
+	rpc->pci_controller.io_resource = &rpc->io_res;
+	rpc->pci_controller.mem_resource = &rpc->mem_res;
+
+	/* Load PCI I/O and memory resources from DT */
+	pci_load_of_ranges(&rpc->pci_controller,
+			   rpc->pci_controller.of_node);
+
+	rt3883_pci_w32(rpc, rpc->mem_res.start, RT3883_PCI_REG_MEMBASE);
+	rt3883_pci_w32(rpc, rpc->io_res.start, RT3883_PCI_REG_IOBASE);
+
+	ioport_resource.start = rpc->io_res.start;
+	ioport_resource.end = rpc->io_res.end;
+
+	/* PCI */
+	rt3883_pci_w32(rpc, 0x03ff0000, RT3883_PCI_REG_BAR0SETUP(0));
+	rt3883_pci_w32(rpc, RT3883_MEMORY_BASE, RT3883_PCI_REG_IMBASEBAR0(0));
+	rt3883_pci_w32(rpc, 0x08021814, RT3883_PCI_REG_ID(0));
+	rt3883_pci_w32(rpc, 0x00800001, RT3883_PCI_REG_CLASS(0));
+	rt3883_pci_w32(rpc, 0x28801814, RT3883_PCI_REG_SUBID(0));
+
+	/* PCIe */
+	rt3883_pci_w32(rpc, 0x03ff0000, RT3883_PCI_REG_BAR0SETUP(1));
+	rt3883_pci_w32(rpc, RT3883_MEMORY_BASE, RT3883_PCI_REG_IMBASEBAR0(1));
+	rt3883_pci_w32(rpc, 0x08021814, RT3883_PCI_REG_ID(1));
+	rt3883_pci_w32(rpc, 0x06040001, RT3883_PCI_REG_CLASS(1));
+	rt3883_pci_w32(rpc, 0x28801814, RT3883_PCI_REG_SUBID(1));
+
+	err = rt3883_pci_irq_init(dev, rpc);
+	if (err)
+		goto err_put_hb_node;
+
+	/* PCIe */
+	val = rt3883_pci_read_cfg32(rpc, 0, 0x01, 0, PCI_COMMAND);
+	val |= PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER;
+	rt3883_pci_write_cfg32(rpc, 0, 0x01, 0, PCI_COMMAND, val);
+
+	/* PCI */
+	val = rt3883_pci_read_cfg32(rpc, 0, 0x00, 0, PCI_COMMAND);
+	val |= PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER;
+	rt3883_pci_write_cfg32(rpc, 0, 0x00, 0, PCI_COMMAND, val);
+
+	if (mode == RT3883_PCI_MODE_PCIE) {
+		rt3883_pci_w32(rpc, 0x03ff0001, RT3883_PCI_REG_BAR0SETUP(0));
+		rt3883_pci_w32(rpc, 0x03ff0001, RT3883_PCI_REG_BAR0SETUP(1));
+
+		rt3883_pci_write_cfg32(rpc, 0, RT3883_P2P_BR_DEVNUM, 0,
+				       PCI_BASE_ADDRESS_0,
+				       RT3883_MEMORY_BASE);
+		/* flush write */
+		rt3883_pci_read_cfg32(rpc, 0, RT3883_P2P_BR_DEVNUM, 0,
+				      PCI_BASE_ADDRESS_0);
+	} else {
+		rt3883_pci_write_cfg32(rpc, 0, RT3883_P2P_BR_DEVNUM, 0,
+				       PCI_IO_BASE, 0x00000101);
+	}
+
+	register_pci_controller(&rpc->pci_controller);
+
+	return 0;
+
+err_put_hb_node:
+	of_node_put(rpc->pci_controller.of_node);
+err_put_intc_node:
+	of_node_put(rpc->intc_of_node);
+	return err;
+}
+
+int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	return of_irq_parse_and_map_pci(dev, slot, pin);
+}
+
+int pcibios_plat_dev_init(struct pci_dev *dev)
+{
+	return 0;
+}
+
+static const struct of_device_id rt3883_pci_ids[] = {
+	{ .compatible = "ralink,rt3883-pci" },
+	{},
+};
+
+static struct platform_driver rt3883_pci_driver = {
+	.probe = rt3883_pci_probe,
+	.driver = {
+		.name = "rt3883-pci",
+		.of_match_table = of_match_ptr(rt3883_pci_ids),
+	},
+};
+
+static int __init rt3883_pci_init(void)
+{
+	return platform_driver_register(&rt3883_pci_driver);
+}
+
+postcore_initcall(rt3883_pci_init);
diff --git a/arch/mips/pci/pci-sb1250.c b/arch/mips/pci/pci-sb1250.c
new file mode 100644
index 000000000..c3f82b280
--- /dev/null
+++ b/arch/mips/pci/pci-sb1250.c
@@ -0,0 +1,279 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2001,2002,2003 Broadcom Corporation
+ * Copyright (C) 2004 by Ralf Baechle (ralf@linux-mips.org)
+ */
+
+/*
+ * BCM1250-specific PCI support
+ *
+ * This module provides the glue between Linux's PCI subsystem
+ * and the hardware.  We basically provide glue for accessing
+ * configuration space, and set up the translation for I/O
+ * space accesses.
+ *
+ * To access configuration space, we use ioremap.  In the 32-bit
+ * kernel, this consumes either 4 or 8 page table pages, and 16MB of
+ * kernel mapped memory.  Hopefully neither of these should be a huge
+ * problem.
+ */
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/console.h>
+#include <linux/tty.h>
+#include <linux/vt.h>
+
+#include <asm/io.h>
+
+#include <asm/sibyte/sb1250_defs.h>
+#include <asm/sibyte/sb1250_regs.h>
+#include <asm/sibyte/sb1250_scd.h>
+#include <asm/sibyte/board.h>
+
+/*
+ * Macros for calculating offsets into config space given a device
+ * structure or dev/fun/reg
+ */
+#define CFGOFFSET(bus, devfn, where) (((bus)<<16) + ((devfn)<<8) + (where))
+#define CFGADDR(bus, devfn, where)   CFGOFFSET((bus)->number, (devfn), where)
+
+static void *cfg_space;
+
+#define PCI_BUS_ENABLED 1
+#define LDT_BUS_ENABLED 2
+#define PCI_DEVICE_MODE 4
+
+static int sb1250_bus_status;
+
+#define PCI_BRIDGE_DEVICE  0
+#define LDT_BRIDGE_DEVICE  1
+
+#ifdef CONFIG_SIBYTE_HAS_LDT
+/*
+ * HT's level-sensitive interrupts require EOI, which is generated
+ * through a 4MB memory-mapped region
+ */
+unsigned long ldt_eoi_space;
+#endif
+
+/*
+ * Read/write 32-bit values in config space.
+ */
+static inline u32 READCFG32(u32 addr)
+{
+	return *(u32 *) (cfg_space + (addr & ~3));
+}
+
+static inline void WRITECFG32(u32 addr, u32 data)
+{
+	*(u32 *) (cfg_space + (addr & ~3)) = data;
+}
+
+int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	return dev->irq;
+}
+
+/* Do platform specific device initialization at pci_enable_device() time */
+int pcibios_plat_dev_init(struct pci_dev *dev)
+{
+	return 0;
+}
+
+/*
+ * Some checks before doing config cycles:
+ * In PCI Device Mode, hide everything on bus 0 except the LDT host
+ * bridge.  Otherwise, access is controlled by bridge MasterEn bits.
+ */
+static int sb1250_pci_can_access(struct pci_bus *bus, int devfn)
+{
+	u32 devno;
+
+	if (!(sb1250_bus_status & (PCI_BUS_ENABLED | PCI_DEVICE_MODE)))
+		return 0;
+
+	if (bus->number == 0) {
+		devno = PCI_SLOT(devfn);
+		if (devno == LDT_BRIDGE_DEVICE)
+			return (sb1250_bus_status & LDT_BUS_ENABLED) != 0;
+		else if (sb1250_bus_status & PCI_DEVICE_MODE)
+			return 0;
+		else
+			return 1;
+	} else
+		return 1;
+}
+
+/*
+ * Read/write access functions for various sizes of values
+ * in config space.  Return all 1's for disallowed accesses
+ * for a kludgy but adequate simulation of master aborts.
+ */
+
+static int sb1250_pcibios_read(struct pci_bus *bus, unsigned int devfn,
+			       int where, int size, u32 * val)
+{
+	u32 data = 0;
+
+	if ((size == 2) && (where & 1))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+	else if ((size == 4) && (where & 3))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+
+	if (sb1250_pci_can_access(bus, devfn))
+		data = READCFG32(CFGADDR(bus, devfn, where));
+	else
+		data = 0xFFFFFFFF;
+
+	if (size == 1)
+		*val = (data >> ((where & 3) << 3)) & 0xff;
+	else if (size == 2)
+		*val = (data >> ((where & 3) << 3)) & 0xffff;
+	else
+		*val = data;
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int sb1250_pcibios_write(struct pci_bus *bus, unsigned int devfn,
+				int where, int size, u32 val)
+{
+	u32 cfgaddr = CFGADDR(bus, devfn, where);
+	u32 data = 0;
+
+	if ((size == 2) && (where & 1))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+	else if ((size == 4) && (where & 3))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+
+	if (!sb1250_pci_can_access(bus, devfn))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+
+	data = READCFG32(cfgaddr);
+
+	if (size == 1)
+		data = (data & ~(0xff << ((where & 3) << 3))) |
+		    (val << ((where & 3) << 3));
+	else if (size == 2)
+		data = (data & ~(0xffff << ((where & 3) << 3))) |
+		    (val << ((where & 3) << 3));
+	else
+		data = val;
+
+	WRITECFG32(cfgaddr, data);
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+struct pci_ops sb1250_pci_ops = {
+	.read	= sb1250_pcibios_read,
+	.write	= sb1250_pcibios_write,
+};
+
+static struct resource sb1250_mem_resource = {
+	.name	= "SB1250 PCI MEM",
+	.start	= 0x40000000UL,
+	.end	= 0x5fffffffUL,
+	.flags	= IORESOURCE_MEM,
+};
+
+static struct resource sb1250_io_resource = {
+	.name	= "SB1250 PCI I/O",
+	.start	= 0x00000000UL,
+	.end	= 0x01ffffffUL,
+	.flags	= IORESOURCE_IO,
+};
+
+struct pci_controller sb1250_controller = {
+	.pci_ops	= &sb1250_pci_ops,
+	.mem_resource	= &sb1250_mem_resource,
+	.io_resource	= &sb1250_io_resource,
+};
+
+static int __init sb1250_pcibios_init(void)
+{
+	void __iomem *io_map_base;
+	uint32_t cmdreg;
+	uint64_t reg;
+
+	/* CFE will assign PCI resources */
+	pci_set_flags(PCI_PROBE_ONLY);
+
+	/* Avoid ISA compat ranges.  */
+	PCIBIOS_MIN_IO = 0x00008000UL;
+	PCIBIOS_MIN_MEM = 0x01000000UL;
+
+	/* Set I/O resource limits.  */
+	ioport_resource.end = 0x01ffffffUL;	/* 32MB accessible by sb1250 */
+	iomem_resource.end = 0xffffffffUL;	/* no HT support yet */
+
+	cfg_space =
+	    ioremap(A_PHYS_LDTPCI_CFG_MATCH_BITS, 16 * 1024 * 1024);
+
+	/*
+	 * See if the PCI bus has been configured by the firmware.
+	 */
+	reg = __raw_readq(IOADDR(A_SCD_SYSTEM_CFG));
+	if (!(reg & M_SYS_PCI_HOST)) {
+		sb1250_bus_status |= PCI_DEVICE_MODE;
+	} else {
+		cmdreg =
+		    READCFG32(CFGOFFSET
+			      (0, PCI_DEVFN(PCI_BRIDGE_DEVICE, 0),
+			       PCI_COMMAND));
+		if (!(cmdreg & PCI_COMMAND_MASTER)) {
+			printk
+			    ("PCI: Skipping PCI probe.	Bus is not initialized.\n");
+			iounmap(cfg_space);
+			return 0;
+		}
+		sb1250_bus_status |= PCI_BUS_ENABLED;
+	}
+
+	/*
+	 * Establish mappings in KSEG2 (kernel virtual) to PCI I/O
+	 * space.  Use "match bytes" policy to make everything look
+	 * little-endian.  So, you need to also set
+	 * CONFIG_SWAP_IO_SPACE, but this is the combination that
+	 * works correctly with most of Linux's drivers.
+	 * XXX ehs: Should this happen in PCI Device mode?
+	 */
+	io_map_base = ioremap(A_PHYS_LDTPCI_IO_MATCH_BYTES, 1024 * 1024);
+	sb1250_controller.io_map_base = (unsigned long)io_map_base;
+	set_io_port_base((unsigned long)io_map_base);
+
+#ifdef CONFIG_SIBYTE_HAS_LDT
+	/*
+	 * Also check the LDT bridge's enable, just in case we didn't
+	 * initialize that one.
+	 */
+
+	cmdreg = READCFG32(CFGOFFSET(0, PCI_DEVFN(LDT_BRIDGE_DEVICE, 0),
+				     PCI_COMMAND));
+	if (cmdreg & PCI_COMMAND_MASTER) {
+		sb1250_bus_status |= LDT_BUS_ENABLED;
+
+		/*
+		 * Need bits 23:16 to convey vector number.  Note that
+		 * this consumes 4MB of kernel-mapped memory
+		 * (Kseg2/Kseg3) for 32-bit kernel.
+		 */
+		ldt_eoi_space = (unsigned long)
+		    ioremap(A_PHYS_LDT_SPECIAL_MATCH_BYTES,
+			    4 * 1024 * 1024);
+	}
+#endif
+
+	register_pci_controller(&sb1250_controller);
+
+#ifdef CONFIG_VGA_CONSOLE
+	console_lock();
+	do_take_over_console(&vga_con, 0, MAX_NR_CONSOLES - 1, 1);
+	console_unlock();
+#endif
+	return 0;
+}
+arch_initcall(sb1250_pcibios_init);
diff --git a/arch/mips/pci/pci-tx4927.c b/arch/mips/pci/pci-tx4927.c
new file mode 100644
index 000000000..9b3301d19
--- /dev/null
+++ b/arch/mips/pci/pci-tx4927.c
@@ -0,0 +1,91 @@
+/*
+ * Based on linux/arch/mips/txx9/rbtx4938/setup.c,
+ *	    and RBTX49xx patch from CELF patch archive.
+ *
+ * Copyright 2001, 2003-2005 MontaVista Software Inc.
+ * Copyright (C) 2004 by Ralf Baechle (ralf@linux-mips.org)
+ * (C) Copyright TOSHIBA CORPORATION 2000-2001, 2004-2007
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#include <linux/init.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/interrupt.h>
+#include <asm/txx9/generic.h>
+#include <asm/txx9/tx4927.h>
+
+int __init tx4927_report_pciclk(void)
+{
+	int pciclk = 0;
+
+	pr_info("PCIC --%s PCICLK:",
+		(__raw_readq(&tx4927_ccfgptr->ccfg) & TX4927_CCFG_PCI66) ?
+		" PCI66" : "");
+	if (__raw_readq(&tx4927_ccfgptr->pcfg) & TX4927_PCFG_PCICLKEN_ALL) {
+		u64 ccfg = __raw_readq(&tx4927_ccfgptr->ccfg);
+		switch ((unsigned long)ccfg &
+			TX4927_CCFG_PCIDIVMODE_MASK) {
+		case TX4927_CCFG_PCIDIVMODE_2_5:
+			pciclk = txx9_cpu_clock * 2 / 5; break;
+		case TX4927_CCFG_PCIDIVMODE_3:
+			pciclk = txx9_cpu_clock / 3; break;
+		case TX4927_CCFG_PCIDIVMODE_5:
+			pciclk = txx9_cpu_clock / 5; break;
+		case TX4927_CCFG_PCIDIVMODE_6:
+			pciclk = txx9_cpu_clock / 6; break;
+		}
+		pr_cont("Internal(%u.%uMHz)",
+			(pciclk + 50000) / 1000000,
+			((pciclk + 50000) / 100000) % 10);
+	} else {
+		pr_cont("External");
+		pciclk = -1;
+	}
+	pr_cont("\n");
+	return pciclk;
+}
+
+int __init tx4927_pciclk66_setup(void)
+{
+	int pciclk;
+
+	/* Assert M66EN */
+	tx4927_ccfg_set(TX4927_CCFG_PCI66);
+	/* Double PCICLK (if possible) */
+	if (__raw_readq(&tx4927_ccfgptr->pcfg) & TX4927_PCFG_PCICLKEN_ALL) {
+		unsigned int pcidivmode = 0;
+		u64 ccfg = __raw_readq(&tx4927_ccfgptr->ccfg);
+		pcidivmode = (unsigned long)ccfg &
+			TX4927_CCFG_PCIDIVMODE_MASK;
+		switch (pcidivmode) {
+		case TX4927_CCFG_PCIDIVMODE_5:
+		case TX4927_CCFG_PCIDIVMODE_2_5:
+			pcidivmode = TX4927_CCFG_PCIDIVMODE_2_5;
+			pciclk = txx9_cpu_clock * 2 / 5;
+			break;
+		case TX4927_CCFG_PCIDIVMODE_6:
+		case TX4927_CCFG_PCIDIVMODE_3:
+		default:
+			pcidivmode = TX4927_CCFG_PCIDIVMODE_3;
+			pciclk = txx9_cpu_clock / 3;
+		}
+		tx4927_ccfg_change(TX4927_CCFG_PCIDIVMODE_MASK,
+				   pcidivmode);
+		pr_debug("PCICLK: ccfg:%08lx\n",
+			 (unsigned long)__raw_readq(&tx4927_ccfgptr->ccfg));
+	} else
+		pciclk = -1;
+	return pciclk;
+}
+
+void __init tx4927_setup_pcierr_irq(void)
+{
+	if (request_irq(TXX9_IRQ_BASE + TX4927_IR_PCIERR,
+			tx4927_pcierr_interrupt,
+			0, "PCI error",
+			(void *)TX4927_PCIC_REG))
+		pr_warn("Failed to request irq for PCIERR\n");
+}
diff --git a/arch/mips/pci/pci-tx4938.c b/arch/mips/pci/pci-tx4938.c
new file mode 100644
index 000000000..a6418460e
--- /dev/null
+++ b/arch/mips/pci/pci-tx4938.c
@@ -0,0 +1,142 @@
+/*
+ * Based on linux/arch/mips/txx9/rbtx4938/setup.c,
+ *	    and RBTX49xx patch from CELF patch archive.
+ *
+ * Copyright 2001, 2003-2005 MontaVista Software Inc.
+ * Copyright (C) 2004 by Ralf Baechle (ralf@linux-mips.org)
+ * (C) Copyright TOSHIBA CORPORATION 2000-2001, 2004-2007
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#include <linux/init.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/interrupt.h>
+#include <asm/txx9/generic.h>
+#include <asm/txx9/tx4938.h>
+
+int __init tx4938_report_pciclk(void)
+{
+	int pciclk = 0;
+
+	pr_info("PCIC --%s PCICLK:",
+		(__raw_readq(&tx4938_ccfgptr->ccfg) & TX4938_CCFG_PCI66) ?
+		" PCI66" : "");
+	if (__raw_readq(&tx4938_ccfgptr->pcfg) & TX4938_PCFG_PCICLKEN_ALL) {
+		u64 ccfg = __raw_readq(&tx4938_ccfgptr->ccfg);
+		switch ((unsigned long)ccfg &
+			TX4938_CCFG_PCIDIVMODE_MASK) {
+		case TX4938_CCFG_PCIDIVMODE_4:
+			pciclk = txx9_cpu_clock / 4; break;
+		case TX4938_CCFG_PCIDIVMODE_4_5:
+			pciclk = txx9_cpu_clock * 2 / 9; break;
+		case TX4938_CCFG_PCIDIVMODE_5:
+			pciclk = txx9_cpu_clock / 5; break;
+		case TX4938_CCFG_PCIDIVMODE_5_5:
+			pciclk = txx9_cpu_clock * 2 / 11; break;
+		case TX4938_CCFG_PCIDIVMODE_8:
+			pciclk = txx9_cpu_clock / 8; break;
+		case TX4938_CCFG_PCIDIVMODE_9:
+			pciclk = txx9_cpu_clock / 9; break;
+		case TX4938_CCFG_PCIDIVMODE_10:
+			pciclk = txx9_cpu_clock / 10; break;
+		case TX4938_CCFG_PCIDIVMODE_11:
+			pciclk = txx9_cpu_clock / 11; break;
+		}
+		pr_cont("Internal(%u.%uMHz)",
+			(pciclk + 50000) / 1000000,
+			((pciclk + 50000) / 100000) % 10);
+	} else {
+		pr_cont("External");
+		pciclk = -1;
+	}
+	pr_cont("\n");
+	return pciclk;
+}
+
+void __init tx4938_report_pci1clk(void)
+{
+	__u64 ccfg = __raw_readq(&tx4938_ccfgptr->ccfg);
+	unsigned int pciclk =
+		txx9_gbus_clock / ((ccfg & TX4938_CCFG_PCI1DMD) ? 4 : 2);
+
+	pr_info("PCIC1 -- %sPCICLK:%u.%uMHz\n",
+		(ccfg & TX4938_CCFG_PCI1_66) ? "PCI66 " : "",
+		(pciclk + 50000) / 1000000,
+		((pciclk + 50000) / 100000) % 10);
+}
+
+int __init tx4938_pciclk66_setup(void)
+{
+	int pciclk;
+
+	/* Assert M66EN */
+	tx4938_ccfg_set(TX4938_CCFG_PCI66);
+	/* Double PCICLK (if possible) */
+	if (__raw_readq(&tx4938_ccfgptr->pcfg) & TX4938_PCFG_PCICLKEN_ALL) {
+		unsigned int pcidivmode = 0;
+		u64 ccfg = __raw_readq(&tx4938_ccfgptr->ccfg);
+		pcidivmode = (unsigned long)ccfg &
+			TX4938_CCFG_PCIDIVMODE_MASK;
+		switch (pcidivmode) {
+		case TX4938_CCFG_PCIDIVMODE_8:
+		case TX4938_CCFG_PCIDIVMODE_4:
+			pcidivmode = TX4938_CCFG_PCIDIVMODE_4;
+			pciclk = txx9_cpu_clock / 4;
+			break;
+		case TX4938_CCFG_PCIDIVMODE_9:
+		case TX4938_CCFG_PCIDIVMODE_4_5:
+			pcidivmode = TX4938_CCFG_PCIDIVMODE_4_5;
+			pciclk = txx9_cpu_clock * 2 / 9;
+			break;
+		case TX4938_CCFG_PCIDIVMODE_10:
+		case TX4938_CCFG_PCIDIVMODE_5:
+			pcidivmode = TX4938_CCFG_PCIDIVMODE_5;
+			pciclk = txx9_cpu_clock / 5;
+			break;
+		case TX4938_CCFG_PCIDIVMODE_11:
+		case TX4938_CCFG_PCIDIVMODE_5_5:
+		default:
+			pcidivmode = TX4938_CCFG_PCIDIVMODE_5_5;
+			pciclk = txx9_cpu_clock * 2 / 11;
+			break;
+		}
+		tx4938_ccfg_change(TX4938_CCFG_PCIDIVMODE_MASK,
+				   pcidivmode);
+		pr_debug("PCICLK: ccfg:%08lx\n",
+			 (unsigned long)__raw_readq(&tx4938_ccfgptr->ccfg));
+	} else
+		pciclk = -1;
+	return pciclk;
+}
+
+int tx4938_pcic1_map_irq(const struct pci_dev *dev, u8 slot)
+{
+	if (get_tx4927_pcicptr(dev->bus->sysdata) == tx4938_pcic1ptr) {
+		switch (slot) {
+		case TX4927_PCIC_IDSEL_AD_TO_SLOT(31):
+			if (__raw_readq(&tx4938_ccfgptr->pcfg) &
+			    TX4938_PCFG_ETH0_SEL)
+				return TXX9_IRQ_BASE + TX4938_IR_ETH0;
+			break;
+		case TX4927_PCIC_IDSEL_AD_TO_SLOT(30):
+			if (__raw_readq(&tx4938_ccfgptr->pcfg) &
+			    TX4938_PCFG_ETH1_SEL)
+				return TXX9_IRQ_BASE + TX4938_IR_ETH1;
+			break;
+		}
+		return 0;
+	}
+	return -1;
+}
+
+void __init tx4938_setup_pcierr_irq(void)
+{
+	if (request_irq(TXX9_IRQ_BASE + TX4938_IR_PCIERR,
+			tx4927_pcierr_interrupt,
+			0, "PCI error",
+			(void *)TX4927_PCIC_REG))
+		pr_warn("Failed to request irq for PCIERR\n");
+}
diff --git a/arch/mips/pci/pci-xtalk-bridge.c b/arch/mips/pci/pci-xtalk-bridge.c
new file mode 100644
index 000000000..ab9bedb82
--- /dev/null
+++ b/arch/mips/pci/pci-xtalk-bridge.c
@@ -0,0 +1,760 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2003 Christoph Hellwig (hch@lst.de)
+ * Copyright (C) 1999, 2000, 04 Ralf Baechle (ralf@linux-mips.org)
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ */
+#include <linux/kernel.h>
+#include <linux/export.h>
+#include <linux/pci.h>
+#include <linux/smp.h>
+#include <linux/dma-direct.h>
+#include <linux/platform_device.h>
+#include <linux/platform_data/xtalk-bridge.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/crc16.h>
+#include <linux/irqdomain.h>
+
+#include <asm/pci/bridge.h>
+#include <asm/paccess.h>
+#include <asm/sn/irq_alloc.h>
+#include <asm/sn/ioc3.h>
+
+#define CRC16_INIT	0
+#define CRC16_VALID	0xb001
+
+/*
+ * Common phys<->dma mapping for platforms using pci xtalk bridge
+ */
+dma_addr_t phys_to_dma(struct device *dev, phys_addr_t paddr)
+{
+	struct pci_dev *pdev = to_pci_dev(dev);
+	struct bridge_controller *bc = BRIDGE_CONTROLLER(pdev->bus);
+
+	return bc->baddr + paddr;
+}
+
+phys_addr_t dma_to_phys(struct device *dev, dma_addr_t dma_addr)
+{
+	return dma_addr & ~(0xffUL << 56);
+}
+
+/*
+ * Most of the IOC3 PCI config register aren't present
+ * we emulate what is needed for a normal PCI enumeration
+ */
+static int ioc3_cfg_rd(void *addr, int where, int size, u32 *value, u32 sid)
+{
+	u32 cf, shift, mask;
+
+	switch (where & ~3) {
+	case 0x00 ... 0x10:
+	case 0x40 ... 0x44:
+		if (get_dbe(cf, (u32 *)addr))
+			return PCIBIOS_DEVICE_NOT_FOUND;
+		break;
+	case 0x2c:
+		cf = sid;
+		break;
+	case 0x3c:
+		/* emulate sane interrupt pin value */
+		cf = 0x00000100;
+		break;
+	default:
+		cf = 0;
+		break;
+	}
+	shift = (where & 3) << 3;
+	mask = 0xffffffffU >> ((4 - size) << 3);
+	*value = (cf >> shift) & mask;
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int ioc3_cfg_wr(void *addr, int where, int size, u32 value)
+{
+	u32 cf, shift, mask, smask;
+
+	if ((where >= 0x14 && where < 0x40) || (where >= 0x48))
+		return PCIBIOS_SUCCESSFUL;
+
+	if (get_dbe(cf, (u32 *)addr))
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	shift = ((where & 3) << 3);
+	mask = (0xffffffffU >> ((4 - size) << 3));
+	smask = mask << shift;
+
+	cf = (cf & ~smask) | ((value & mask) << shift);
+	if (put_dbe(cf, (u32 *)addr))
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static void bridge_disable_swapping(struct pci_dev *dev)
+{
+	struct bridge_controller *bc = BRIDGE_CONTROLLER(dev->bus);
+	int slot = PCI_SLOT(dev->devfn);
+
+	/* Turn off byte swapping */
+	bridge_clr(bc, b_device[slot].reg, BRIDGE_DEV_SWAP_DIR);
+	bridge_read(bc, b_widget.w_tflush);	/* Flush */
+}
+
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SGI, PCI_DEVICE_ID_SGI_IOC3,
+	bridge_disable_swapping);
+
+
+/*
+ * The Bridge ASIC supports both type 0 and type 1 access.  Type 1 is
+ * not really documented, so right now I can't write code which uses it.
+ * Therefore we use type 0 accesses for now even though they won't work
+ * correctly for PCI-to-PCI bridges.
+ *
+ * The function is complicated by the ultimate brokenness of the IOC3 chip
+ * which is used in SGI systems.  The IOC3 can only handle 32-bit PCI
+ * accesses and does only decode parts of it's address space.
+ */
+static int pci_conf0_read_config(struct pci_bus *bus, unsigned int devfn,
+				 int where, int size, u32 *value)
+{
+	struct bridge_controller *bc = BRIDGE_CONTROLLER(bus);
+	struct bridge_regs *bridge = bc->base;
+	int slot = PCI_SLOT(devfn);
+	int fn = PCI_FUNC(devfn);
+	void *addr;
+	u32 cf;
+	int res;
+
+	addr = &bridge->b_type0_cfg_dev[slot].f[fn].c[PCI_VENDOR_ID];
+	if (get_dbe(cf, (u32 *)addr))
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	/*
+	 * IOC3 is broken beyond belief ...  Don't even give the
+	 * generic PCI code a chance to look at it for real ...
+	 */
+	if (cf == (PCI_VENDOR_ID_SGI | (PCI_DEVICE_ID_SGI_IOC3 << 16))) {
+		addr = &bridge->b_type0_cfg_dev[slot].f[fn].l[where >> 2];
+		return ioc3_cfg_rd(addr, where, size, value,
+				   bc->ioc3_sid[slot]);
+	}
+
+	addr = &bridge->b_type0_cfg_dev[slot].f[fn].c[where ^ (4 - size)];
+
+	if (size == 1)
+		res = get_dbe(*value, (u8 *)addr);
+	else if (size == 2)
+		res = get_dbe(*value, (u16 *)addr);
+	else
+		res = get_dbe(*value, (u32 *)addr);
+
+	return res ? PCIBIOS_DEVICE_NOT_FOUND : PCIBIOS_SUCCESSFUL;
+}
+
+static int pci_conf1_read_config(struct pci_bus *bus, unsigned int devfn,
+				 int where, int size, u32 *value)
+{
+	struct bridge_controller *bc = BRIDGE_CONTROLLER(bus);
+	struct bridge_regs *bridge = bc->base;
+	int busno = bus->number;
+	int slot = PCI_SLOT(devfn);
+	int fn = PCI_FUNC(devfn);
+	void *addr;
+	u32 cf;
+	int res;
+
+	bridge_write(bc, b_pci_cfg, (busno << 16) | (slot << 11));
+	addr = &bridge->b_type1_cfg.c[(fn << 8) | PCI_VENDOR_ID];
+	if (get_dbe(cf, (u32 *)addr))
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	/*
+	 * IOC3 is broken beyond belief ...  Don't even give the
+	 * generic PCI code a chance to look at it for real ...
+	 */
+	if (cf == (PCI_VENDOR_ID_SGI | (PCI_DEVICE_ID_SGI_IOC3 << 16))) {
+		addr = &bridge->b_type1_cfg.c[(fn << 8) | (where & ~3)];
+		return ioc3_cfg_rd(addr, where, size, value,
+				   bc->ioc3_sid[slot]);
+	}
+
+	addr = &bridge->b_type1_cfg.c[(fn << 8) | (where ^ (4 - size))];
+
+	if (size == 1)
+		res = get_dbe(*value, (u8 *)addr);
+	else if (size == 2)
+		res = get_dbe(*value, (u16 *)addr);
+	else
+		res = get_dbe(*value, (u32 *)addr);
+
+	return res ? PCIBIOS_DEVICE_NOT_FOUND : PCIBIOS_SUCCESSFUL;
+}
+
+static int pci_read_config(struct pci_bus *bus, unsigned int devfn,
+			   int where, int size, u32 *value)
+{
+	if (!pci_is_root_bus(bus))
+		return pci_conf1_read_config(bus, devfn, where, size, value);
+
+	return pci_conf0_read_config(bus, devfn, where, size, value);
+}
+
+static int pci_conf0_write_config(struct pci_bus *bus, unsigned int devfn,
+				  int where, int size, u32 value)
+{
+	struct bridge_controller *bc = BRIDGE_CONTROLLER(bus);
+	struct bridge_regs *bridge = bc->base;
+	int slot = PCI_SLOT(devfn);
+	int fn = PCI_FUNC(devfn);
+	void *addr;
+	u32 cf;
+	int res;
+
+	addr = &bridge->b_type0_cfg_dev[slot].f[fn].c[PCI_VENDOR_ID];
+	if (get_dbe(cf, (u32 *)addr))
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	/*
+	 * IOC3 is broken beyond belief ...  Don't even give the
+	 * generic PCI code a chance to look at it for real ...
+	 */
+	if (cf == (PCI_VENDOR_ID_SGI | (PCI_DEVICE_ID_SGI_IOC3 << 16))) {
+		addr = &bridge->b_type0_cfg_dev[slot].f[fn].l[where >> 2];
+		return ioc3_cfg_wr(addr, where, size, value);
+	}
+
+	addr = &bridge->b_type0_cfg_dev[slot].f[fn].c[where ^ (4 - size)];
+
+	if (size == 1)
+		res = put_dbe(value, (u8 *)addr);
+	else if (size == 2)
+		res = put_dbe(value, (u16 *)addr);
+	else
+		res = put_dbe(value, (u32 *)addr);
+
+	if (res)
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int pci_conf1_write_config(struct pci_bus *bus, unsigned int devfn,
+				  int where, int size, u32 value)
+{
+	struct bridge_controller *bc = BRIDGE_CONTROLLER(bus);
+	struct bridge_regs *bridge = bc->base;
+	int slot = PCI_SLOT(devfn);
+	int fn = PCI_FUNC(devfn);
+	int busno = bus->number;
+	void *addr;
+	u32 cf;
+	int res;
+
+	bridge_write(bc, b_pci_cfg, (busno << 16) | (slot << 11));
+	addr = &bridge->b_type1_cfg.c[(fn << 8) | PCI_VENDOR_ID];
+	if (get_dbe(cf, (u32 *)addr))
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	/*
+	 * IOC3 is broken beyond belief ...  Don't even give the
+	 * generic PCI code a chance to look at it for real ...
+	 */
+	if (cf == (PCI_VENDOR_ID_SGI | (PCI_DEVICE_ID_SGI_IOC3 << 16))) {
+		addr = &bridge->b_type0_cfg_dev[slot].f[fn].l[where >> 2];
+		return ioc3_cfg_wr(addr, where, size, value);
+	}
+
+	addr = &bridge->b_type1_cfg.c[(fn << 8) | (where ^ (4 - size))];
+
+	if (size == 1)
+		res = put_dbe(value, (u8 *)addr);
+	else if (size == 2)
+		res = put_dbe(value, (u16 *)addr);
+	else
+		res = put_dbe(value, (u32 *)addr);
+
+	if (res)
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int pci_write_config(struct pci_bus *bus, unsigned int devfn,
+	int where, int size, u32 value)
+{
+	if (!pci_is_root_bus(bus))
+		return pci_conf1_write_config(bus, devfn, where, size, value);
+
+	return pci_conf0_write_config(bus, devfn, where, size, value);
+}
+
+static struct pci_ops bridge_pci_ops = {
+	.read	 = pci_read_config,
+	.write	 = pci_write_config,
+};
+
+struct bridge_irq_chip_data {
+	struct bridge_controller *bc;
+	nasid_t nasid;
+};
+
+static int bridge_set_affinity(struct irq_data *d, const struct cpumask *mask,
+			       bool force)
+{
+#ifdef CONFIG_NUMA
+	struct bridge_irq_chip_data *data = d->chip_data;
+	int bit = d->parent_data->hwirq;
+	int pin = d->hwirq;
+	int ret, cpu;
+
+	ret = irq_chip_set_affinity_parent(d, mask, force);
+	if (ret >= 0) {
+		cpu = cpumask_first_and(mask, cpu_online_mask);
+		data->nasid = cpu_to_node(cpu);
+		bridge_write(data->bc, b_int_addr[pin].addr,
+			     (((data->bc->intr_addr >> 30) & 0x30000) |
+			      bit | (data->nasid << 8)));
+		bridge_read(data->bc, b_wid_tflush);
+	}
+	return ret;
+#else
+	return irq_chip_set_affinity_parent(d, mask, force);
+#endif
+}
+
+struct irq_chip bridge_irq_chip = {
+	.name             = "BRIDGE",
+	.irq_mask         = irq_chip_mask_parent,
+	.irq_unmask       = irq_chip_unmask_parent,
+	.irq_set_affinity = bridge_set_affinity
+};
+
+static int bridge_domain_alloc(struct irq_domain *domain, unsigned int virq,
+			       unsigned int nr_irqs, void *arg)
+{
+	struct bridge_irq_chip_data *data;
+	struct irq_alloc_info *info = arg;
+	int ret;
+
+	if (nr_irqs > 1 || !info)
+		return -EINVAL;
+
+	data = kzalloc(sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	ret = irq_domain_alloc_irqs_parent(domain, virq, nr_irqs, arg);
+	if (ret >= 0) {
+		data->bc = info->ctrl;
+		data->nasid = info->nasid;
+		irq_domain_set_info(domain, virq, info->pin, &bridge_irq_chip,
+				    data, handle_level_irq, NULL, NULL);
+	} else {
+		kfree(data);
+	}
+
+	return ret;
+}
+
+static void bridge_domain_free(struct irq_domain *domain, unsigned int virq,
+			       unsigned int nr_irqs)
+{
+	struct irq_data *irqd = irq_domain_get_irq_data(domain, virq);
+
+	if (nr_irqs)
+		return;
+
+	kfree(irqd->chip_data);
+	irq_domain_free_irqs_top(domain, virq, nr_irqs);
+}
+
+static int bridge_domain_activate(struct irq_domain *domain,
+				  struct irq_data *irqd, bool reserve)
+{
+	struct bridge_irq_chip_data *data = irqd->chip_data;
+	struct bridge_controller *bc = data->bc;
+	int bit = irqd->parent_data->hwirq;
+	int pin = irqd->hwirq;
+	u32 device;
+
+	bridge_write(bc, b_int_addr[pin].addr,
+		     (((bc->intr_addr >> 30) & 0x30000) |
+		      bit | (data->nasid << 8)));
+	bridge_set(bc, b_int_enable, (1 << pin));
+	bridge_set(bc, b_int_enable, 0x7ffffe00); /* more stuff in int_enable */
+
+	/*
+	 * Enable sending of an interrupt clear packet to the hub on a high to
+	 * low transition of the interrupt pin.
+	 *
+	 * IRIX sets additional bits in the address which are documented as
+	 * reserved in the bridge docs.
+	 */
+	bridge_set(bc, b_int_mode, (1UL << pin));
+
+	/*
+	 * We assume the bridge to have a 1:1 mapping between devices
+	 * (slots) and intr pins.
+	 */
+	device = bridge_read(bc, b_int_device);
+	device &= ~(7 << (pin*3));
+	device |= (pin << (pin*3));
+	bridge_write(bc, b_int_device, device);
+
+	bridge_read(bc, b_wid_tflush);
+	return 0;
+}
+
+static void bridge_domain_deactivate(struct irq_domain *domain,
+				     struct irq_data *irqd)
+{
+	struct bridge_irq_chip_data *data = irqd->chip_data;
+
+	bridge_clr(data->bc, b_int_enable, (1 << irqd->hwirq));
+	bridge_read(data->bc, b_wid_tflush);
+}
+
+static const struct irq_domain_ops bridge_domain_ops = {
+	.alloc      = bridge_domain_alloc,
+	.free       = bridge_domain_free,
+	.activate   = bridge_domain_activate,
+	.deactivate = bridge_domain_deactivate
+};
+
+/*
+ * All observed requests have pin == 1. We could have a global here, that
+ * gets incremented and returned every time - unfortunately, pci_map_irq
+ * may be called on the same device over and over, and need to return the
+ * same value. On O2000, pin can be 0 or 1, and PCI slots can be [0..7].
+ *
+ * A given PCI device, in general, should be able to intr any of the cpus
+ * on any one of the hubs connected to its xbow.
+ */
+static int bridge_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	struct bridge_controller *bc = BRIDGE_CONTROLLER(dev->bus);
+	struct irq_alloc_info info;
+	int irq;
+
+	switch (pin) {
+	case PCI_INTERRUPT_UNKNOWN:
+	case PCI_INTERRUPT_INTA:
+	case PCI_INTERRUPT_INTC:
+		pin = 0;
+		break;
+	case PCI_INTERRUPT_INTB:
+	case PCI_INTERRUPT_INTD:
+		pin = 1;
+	}
+
+	irq = bc->pci_int[slot][pin];
+	if (irq == -1) {
+		info.ctrl = bc;
+		info.nasid = bc->nasid;
+		info.pin = bc->int_mapping[slot][pin];
+
+		irq = irq_domain_alloc_irqs(bc->domain, 1, bc->nasid, &info);
+		if (irq < 0)
+			return irq;
+
+		bc->pci_int[slot][pin] = irq;
+	}
+	return irq;
+}
+
+#define IOC3_SID(sid)	(PCI_VENDOR_ID_SGI | ((sid) << 16))
+
+static void bridge_setup_ip27_baseio6g(struct bridge_controller *bc)
+{
+	bc->ioc3_sid[2] = IOC3_SID(IOC3_SUBSYS_IP27_BASEIO6G);
+	bc->ioc3_sid[6] = IOC3_SID(IOC3_SUBSYS_IP27_MIO);
+	bc->int_mapping[2][1] = 4;
+	bc->int_mapping[6][1] = 6;
+}
+
+static void bridge_setup_ip27_baseio(struct bridge_controller *bc)
+{
+	bc->ioc3_sid[2] = IOC3_SID(IOC3_SUBSYS_IP27_BASEIO);
+	bc->int_mapping[2][1] = 4;
+}
+
+static void bridge_setup_ip29_baseio(struct bridge_controller *bc)
+{
+	bc->ioc3_sid[2] = IOC3_SID(IOC3_SUBSYS_IP29_SYSBOARD);
+	bc->int_mapping[2][1] = 3;
+}
+
+static void bridge_setup_ip30_sysboard(struct bridge_controller *bc)
+{
+	bc->ioc3_sid[2] = IOC3_SID(IOC3_SUBSYS_IP30_SYSBOARD);
+	bc->int_mapping[2][1] = 4;
+}
+
+static void bridge_setup_menet(struct bridge_controller *bc)
+{
+	bc->ioc3_sid[0] = IOC3_SID(IOC3_SUBSYS_MENET);
+	bc->ioc3_sid[1] = IOC3_SID(IOC3_SUBSYS_MENET);
+	bc->ioc3_sid[2] = IOC3_SID(IOC3_SUBSYS_MENET);
+	bc->ioc3_sid[3] = IOC3_SID(IOC3_SUBSYS_MENET4);
+}
+
+static void bridge_setup_io7(struct bridge_controller *bc)
+{
+	bc->ioc3_sid[4] = IOC3_SID(IOC3_SUBSYS_IO7);
+}
+
+static void bridge_setup_io8(struct bridge_controller *bc)
+{
+	bc->ioc3_sid[4] = IOC3_SID(IOC3_SUBSYS_IO8);
+}
+
+static void bridge_setup_io9(struct bridge_controller *bc)
+{
+	bc->ioc3_sid[1] = IOC3_SID(IOC3_SUBSYS_IO9);
+}
+
+static void bridge_setup_ip34_fuel_sysboard(struct bridge_controller *bc)
+{
+	bc->ioc3_sid[4] = IOC3_SID(IOC3_SUBSYS_IP34_SYSBOARD);
+}
+
+#define BRIDGE_BOARD_SETUP(_partno, _setup)	\
+	{ .match = _partno, .setup = _setup }
+
+static const struct {
+	char *match;
+	void (*setup)(struct bridge_controller *bc);
+} bridge_ioc3_devid[] = {
+	BRIDGE_BOARD_SETUP("030-0734-", bridge_setup_ip27_baseio6g),
+	BRIDGE_BOARD_SETUP("030-0880-", bridge_setup_ip27_baseio6g),
+	BRIDGE_BOARD_SETUP("030-1023-", bridge_setup_ip27_baseio),
+	BRIDGE_BOARD_SETUP("030-1124-", bridge_setup_ip27_baseio),
+	BRIDGE_BOARD_SETUP("030-1025-", bridge_setup_ip29_baseio),
+	BRIDGE_BOARD_SETUP("030-1244-", bridge_setup_ip29_baseio),
+	BRIDGE_BOARD_SETUP("030-1389-", bridge_setup_ip29_baseio),
+	BRIDGE_BOARD_SETUP("030-0887-", bridge_setup_ip30_sysboard),
+	BRIDGE_BOARD_SETUP("030-1467-", bridge_setup_ip30_sysboard),
+	BRIDGE_BOARD_SETUP("030-0873-", bridge_setup_menet),
+	BRIDGE_BOARD_SETUP("030-1557-", bridge_setup_io7),
+	BRIDGE_BOARD_SETUP("030-1673-", bridge_setup_io8),
+	BRIDGE_BOARD_SETUP("030-1771-", bridge_setup_io9),
+	BRIDGE_BOARD_SETUP("030-1707-", bridge_setup_ip34_fuel_sysboard),
+};
+
+static void bridge_setup_board(struct bridge_controller *bc, char *partnum)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(bridge_ioc3_devid); i++)
+		if (!strncmp(partnum, bridge_ioc3_devid[i].match,
+			     strlen(bridge_ioc3_devid[i].match))) {
+			bridge_ioc3_devid[i].setup(bc);
+		}
+}
+
+static int bridge_nvmem_match(struct device *dev, const void *data)
+{
+	const char *name = dev_name(dev);
+	const char *prefix = data;
+
+	if (strlen(name) < strlen(prefix))
+		return 0;
+
+	return memcmp(prefix, dev_name(dev), strlen(prefix)) == 0;
+}
+
+static int bridge_get_partnum(u64 baddr, char *partnum)
+{
+	struct nvmem_device *nvmem;
+	char prefix[24];
+	u8 prom[64];
+	int i, j;
+	int ret;
+
+	snprintf(prefix, sizeof(prefix), "bridge-%012llx-0b-", baddr);
+
+	nvmem = nvmem_device_find(prefix, bridge_nvmem_match);
+	if (IS_ERR(nvmem))
+		return PTR_ERR(nvmem);
+
+	ret = nvmem_device_read(nvmem, 0, 64, prom);
+	nvmem_device_put(nvmem);
+
+	if (ret != 64)
+		return ret;
+
+	if (crc16(CRC16_INIT, prom, 32) != CRC16_VALID ||
+	    crc16(CRC16_INIT, prom + 32, 32) != CRC16_VALID)
+		return -EINVAL;
+
+	/* Assemble part number */
+	j = 0;
+	for (i = 0; i < 19; i++)
+		if (prom[i + 11] != ' ')
+			partnum[j++] = prom[i + 11];
+
+	for (i = 0; i < 6; i++)
+		if (prom[i + 32] != ' ')
+			partnum[j++] = prom[i + 32];
+
+	partnum[j] = 0;
+
+	return 0;
+}
+
+static int bridge_probe(struct platform_device *pdev)
+{
+	struct xtalk_bridge_platform_data *bd = dev_get_platdata(&pdev->dev);
+	struct device *dev = &pdev->dev;
+	struct bridge_controller *bc;
+	struct pci_host_bridge *host;
+	struct irq_domain *domain, *parent;
+	struct fwnode_handle *fn;
+	char partnum[26];
+	int slot;
+	int err;
+
+	/* get part number from one wire prom */
+	if (bridge_get_partnum(virt_to_phys((void *)bd->bridge_addr), partnum))
+		return -EPROBE_DEFER; /* not available yet */
+
+	parent = irq_get_default_host();
+	if (!parent)
+		return -ENODEV;
+	fn = irq_domain_alloc_named_fwnode("BRIDGE");
+	if (!fn)
+		return -ENOMEM;
+	domain = irq_domain_create_hierarchy(parent, 0, 8, fn,
+					     &bridge_domain_ops, NULL);
+	if (!domain) {
+		irq_domain_free_fwnode(fn);
+		return -ENOMEM;
+	}
+
+	pci_set_flags(PCI_PROBE_ONLY);
+
+	host = devm_pci_alloc_host_bridge(dev, sizeof(*bc));
+	if (!host) {
+		err = -ENOMEM;
+		goto err_remove_domain;
+	}
+
+	bc = pci_host_bridge_priv(host);
+
+	bc->busn.name		= "Bridge PCI busn";
+	bc->busn.start		= 0;
+	bc->busn.end		= 0xff;
+	bc->busn.flags		= IORESOURCE_BUS;
+
+	bc->domain		= domain;
+
+	pci_add_resource_offset(&host->windows, &bd->mem, bd->mem_offset);
+	pci_add_resource_offset(&host->windows, &bd->io, bd->io_offset);
+	pci_add_resource(&host->windows, &bc->busn);
+
+	err = devm_request_pci_bus_resources(dev, &host->windows);
+	if (err < 0)
+		goto err_free_resource;
+
+	bc->nasid = bd->nasid;
+
+	bc->baddr = (u64)bd->masterwid << 60 | PCI64_ATTR_BAR;
+	bc->base = (struct bridge_regs *)bd->bridge_addr;
+	bc->intr_addr = bd->intr_addr;
+
+	/*
+	 * Clear all pending interrupts.
+	 */
+	bridge_write(bc, b_int_rst_stat, BRIDGE_IRR_ALL_CLR);
+
+	/*
+	 * Until otherwise set up, assume all interrupts are from slot 0
+	 */
+	bridge_write(bc, b_int_device, 0x0);
+
+	/*
+	 * disable swapping for big windows
+	 */
+	bridge_clr(bc, b_wid_control,
+		   BRIDGE_CTRL_IO_SWAP | BRIDGE_CTRL_MEM_SWAP);
+#ifdef CONFIG_PAGE_SIZE_4KB
+	bridge_clr(bc, b_wid_control, BRIDGE_CTRL_PAGE_SIZE);
+#else /* 16kB or larger */
+	bridge_set(bc, b_wid_control, BRIDGE_CTRL_PAGE_SIZE);
+#endif
+
+	/*
+	 * Hmm...  IRIX sets additional bits in the address which
+	 * are documented as reserved in the bridge docs.
+	 */
+	bridge_write(bc, b_wid_int_upper,
+		     ((bc->intr_addr >> 32) & 0xffff) | (bd->masterwid << 16));
+	bridge_write(bc, b_wid_int_lower, bc->intr_addr & 0xffffffff);
+	bridge_write(bc, b_dir_map, (bd->masterwid << 20));	/* DMA */
+	bridge_write(bc, b_int_enable, 0);
+
+	for (slot = 0; slot < 8; slot++) {
+		bridge_set(bc, b_device[slot].reg, BRIDGE_DEV_SWAP_DIR);
+		bc->pci_int[slot][0] = -1;
+		bc->pci_int[slot][1] = -1;
+		/* default interrupt pin mapping */
+		bc->int_mapping[slot][0] = slot;
+		bc->int_mapping[slot][1] = slot ^ 4;
+	}
+	bridge_read(bc, b_wid_tflush);	  /* wait until Bridge PIO complete */
+
+	bridge_setup_board(bc, partnum);
+
+	host->dev.parent = dev;
+	host->sysdata = bc;
+	host->busnr = 0;
+	host->ops = &bridge_pci_ops;
+	host->map_irq = bridge_map_irq;
+	host->swizzle_irq = pci_common_swizzle;
+
+	err = pci_scan_root_bus_bridge(host);
+	if (err < 0)
+		goto err_free_resource;
+
+	pci_bus_claim_resources(host->bus);
+	pci_bus_add_devices(host->bus);
+
+	platform_set_drvdata(pdev, host->bus);
+
+	return 0;
+
+err_free_resource:
+	pci_free_resource_list(&host->windows);
+err_remove_domain:
+	irq_domain_remove(domain);
+	irq_domain_free_fwnode(fn);
+	return err;
+}
+
+static int bridge_remove(struct platform_device *pdev)
+{
+	struct pci_bus *bus = platform_get_drvdata(pdev);
+	struct bridge_controller *bc = BRIDGE_CONTROLLER(bus);
+	struct fwnode_handle *fn = bc->domain->fwnode;
+
+	irq_domain_remove(bc->domain);
+	irq_domain_free_fwnode(fn);
+	pci_lock_rescan_remove();
+	pci_stop_root_bus(bus);
+	pci_remove_root_bus(bus);
+	pci_unlock_rescan_remove();
+
+	return 0;
+}
+
+static struct platform_driver bridge_driver = {
+	.probe  = bridge_probe,
+	.remove = bridge_remove,
+	.driver = {
+		.name = "xtalk-bridge",
+	}
+};
+
+builtin_platform_driver(bridge_driver);
diff --git a/arch/mips/pci/pci.c b/arch/mips/pci/pci.c
new file mode 100644
index 000000000..feebc6eee
--- /dev/null
+++ b/arch/mips/pci/pci.c
@@ -0,0 +1,55 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *
+ * Copyright (C) 2003, 04, 11 Ralf Baechle (ralf@linux-mips.org)
+ * Copyright (C) 2011 Wind River Systems,
+ *   written by Ralf Baechle (ralf@linux-mips.org)
+ */
+#include <linux/bug.h>
+#include <linux/kernel.h>
+#include <linux/mm.h>
+#include <linux/memblock.h>
+#include <linux/export.h>
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/of_address.h>
+
+#include <asm/cpu-info.h>
+
+unsigned long PCIBIOS_MIN_IO;
+EXPORT_SYMBOL(PCIBIOS_MIN_IO);
+
+unsigned long PCIBIOS_MIN_MEM;
+EXPORT_SYMBOL(PCIBIOS_MIN_MEM);
+
+static int __init pcibios_set_cache_line_size(void)
+{
+	unsigned int lsize;
+
+	/*
+	 * Set PCI cacheline size to that of the highest level in the
+	 * cache hierarchy.
+	 */
+	lsize = cpu_dcache_line_size();
+	lsize = cpu_scache_line_size() ? : lsize;
+	lsize = cpu_tcache_line_size() ? : lsize;
+
+	BUG_ON(!lsize);
+
+	pci_dfl_cache_line_size = lsize >> 2;
+
+	pr_debug("PCI: pci_cache_line_size set to %d bytes\n", lsize);
+	return 0;
+}
+arch_initcall(pcibios_set_cache_line_size);
+
+void pci_resource_to_user(const struct pci_dev *dev, int bar,
+			  const struct resource *rsrc, resource_size_t *start,
+			  resource_size_t *end)
+{
+	phys_addr_t size = resource_size(rsrc);
+
+	*start = fixup_bigphys_addr(rsrc->start, size);
+	*end = rsrc->start + size - 1;
+}
diff --git a/arch/mips/pci/pcie-octeon.c b/arch/mips/pci/pcie-octeon.c
new file mode 100644
index 000000000..c9edd3fb3
--- /dev/null
+++ b/arch/mips/pci/pcie-octeon.c
@@ -0,0 +1,2088 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2007, 2008, 2009, 2010, 2011 Cavium Networks
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/pci.h>
+#include <linux/interrupt.h>
+#include <linux/time.h>
+#include <linux/delay.h>
+#include <linux/moduleparam.h>
+
+#include <asm/octeon/octeon.h>
+#include <asm/octeon/cvmx-npei-defs.h>
+#include <asm/octeon/cvmx-pciercx-defs.h>
+#include <asm/octeon/cvmx-pescx-defs.h>
+#include <asm/octeon/cvmx-pexp-defs.h>
+#include <asm/octeon/cvmx-pemx-defs.h>
+#include <asm/octeon/cvmx-dpi-defs.h>
+#include <asm/octeon/cvmx-sli-defs.h>
+#include <asm/octeon/cvmx-sriox-defs.h>
+#include <asm/octeon/cvmx-helper-errata.h>
+#include <asm/octeon/pci-octeon.h>
+
+#define MRRS_CN5XXX 0 /* 128 byte Max Read Request Size */
+#define MPS_CN5XXX  0 /* 128 byte Max Packet Size (Limit of most PCs) */
+#define MRRS_CN6XXX 3 /* 1024 byte Max Read Request Size */
+#define MPS_CN6XXX  0 /* 128 byte Max Packet Size (Limit of most PCs) */
+
+/* Module parameter to disable PCI probing */
+static int pcie_disable;
+module_param(pcie_disable, int, S_IRUGO);
+
+static int enable_pcie_14459_war;
+static int enable_pcie_bus_num_war[2];
+
+union cvmx_pcie_address {
+	uint64_t u64;
+	struct {
+		uint64_t upper:2;	/* Normally 2 for XKPHYS */
+		uint64_t reserved_49_61:13;	/* Must be zero */
+		uint64_t io:1;	/* 1 for IO space access */
+		uint64_t did:5; /* PCIe DID = 3 */
+		uint64_t subdid:3;	/* PCIe SubDID = 1 */
+		uint64_t reserved_36_39:4;	/* Must be zero */
+		uint64_t es:2;	/* Endian swap = 1 */
+		uint64_t port:2;	/* PCIe port 0,1 */
+		uint64_t reserved_29_31:3;	/* Must be zero */
+		/*
+		 * Selects the type of the configuration request (0 = type 0,
+		 * 1 = type 1).
+		 */
+		uint64_t ty:1;
+		/* Target bus number sent in the ID in the request. */
+		uint64_t bus:8;
+		/*
+		 * Target device number sent in the ID in the
+		 * request. Note that Dev must be zero for type 0
+		 * configuration requests.
+		 */
+		uint64_t dev:5;
+		/* Target function number sent in the ID in the request. */
+		uint64_t func:3;
+		/*
+		 * Selects a register in the configuration space of
+		 * the target.
+		 */
+		uint64_t reg:12;
+	} config;
+	struct {
+		uint64_t upper:2;	/* Normally 2 for XKPHYS */
+		uint64_t reserved_49_61:13;	/* Must be zero */
+		uint64_t io:1;	/* 1 for IO space access */
+		uint64_t did:5; /* PCIe DID = 3 */
+		uint64_t subdid:3;	/* PCIe SubDID = 2 */
+		uint64_t reserved_36_39:4;	/* Must be zero */
+		uint64_t es:2;	/* Endian swap = 1 */
+		uint64_t port:2;	/* PCIe port 0,1 */
+		uint64_t address:32;	/* PCIe IO address */
+	} io;
+	struct {
+		uint64_t upper:2;	/* Normally 2 for XKPHYS */
+		uint64_t reserved_49_61:13;	/* Must be zero */
+		uint64_t io:1;	/* 1 for IO space access */
+		uint64_t did:5; /* PCIe DID = 3 */
+		uint64_t subdid:3;	/* PCIe SubDID = 3-6 */
+		uint64_t reserved_36_39:4;	/* Must be zero */
+		uint64_t address:36;	/* PCIe Mem address */
+	} mem;
+};
+
+static int cvmx_pcie_rc_initialize(int pcie_port);
+
+/**
+ * Return the Core virtual base address for PCIe IO access. IOs are
+ * read/written as an offset from this address.
+ *
+ * @pcie_port: PCIe port the IO is for
+ *
+ * Returns 64bit Octeon IO base address for read/write
+ */
+static inline uint64_t cvmx_pcie_get_io_base_address(int pcie_port)
+{
+	union cvmx_pcie_address pcie_addr;
+	pcie_addr.u64 = 0;
+	pcie_addr.io.upper = 0;
+	pcie_addr.io.io = 1;
+	pcie_addr.io.did = 3;
+	pcie_addr.io.subdid = 2;
+	pcie_addr.io.es = 1;
+	pcie_addr.io.port = pcie_port;
+	return pcie_addr.u64;
+}
+
+/**
+ * Size of the IO address region returned at address
+ * cvmx_pcie_get_io_base_address()
+ *
+ * @pcie_port: PCIe port the IO is for
+ *
+ * Returns Size of the IO window
+ */
+static inline uint64_t cvmx_pcie_get_io_size(int pcie_port)
+{
+	return 1ull << 32;
+}
+
+/**
+ * Return the Core virtual base address for PCIe MEM access. Memory is
+ * read/written as an offset from this address.
+ *
+ * @pcie_port: PCIe port the IO is for
+ *
+ * Returns 64bit Octeon IO base address for read/write
+ */
+static inline uint64_t cvmx_pcie_get_mem_base_address(int pcie_port)
+{
+	union cvmx_pcie_address pcie_addr;
+	pcie_addr.u64 = 0;
+	pcie_addr.mem.upper = 0;
+	pcie_addr.mem.io = 1;
+	pcie_addr.mem.did = 3;
+	pcie_addr.mem.subdid = 3 + pcie_port;
+	return pcie_addr.u64;
+}
+
+/**
+ * Size of the Mem address region returned at address
+ * cvmx_pcie_get_mem_base_address()
+ *
+ * @pcie_port: PCIe port the IO is for
+ *
+ * Returns Size of the Mem window
+ */
+static inline uint64_t cvmx_pcie_get_mem_size(int pcie_port)
+{
+	return 1ull << 36;
+}
+
+/**
+ * Read a PCIe config space register indirectly. This is used for
+ * registers of the form PCIEEP_CFG??? and PCIERC?_CFG???.
+ *
+ * @pcie_port:	PCIe port to read from
+ * @cfg_offset: Address to read
+ *
+ * Returns Value read
+ */
+static uint32_t cvmx_pcie_cfgx_read(int pcie_port, uint32_t cfg_offset)
+{
+	if (octeon_has_feature(OCTEON_FEATURE_NPEI)) {
+		union cvmx_pescx_cfg_rd pescx_cfg_rd;
+		pescx_cfg_rd.u64 = 0;
+		pescx_cfg_rd.s.addr = cfg_offset;
+		cvmx_write_csr(CVMX_PESCX_CFG_RD(pcie_port), pescx_cfg_rd.u64);
+		pescx_cfg_rd.u64 = cvmx_read_csr(CVMX_PESCX_CFG_RD(pcie_port));
+		return pescx_cfg_rd.s.data;
+	} else {
+		union cvmx_pemx_cfg_rd pemx_cfg_rd;
+		pemx_cfg_rd.u64 = 0;
+		pemx_cfg_rd.s.addr = cfg_offset;
+		cvmx_write_csr(CVMX_PEMX_CFG_RD(pcie_port), pemx_cfg_rd.u64);
+		pemx_cfg_rd.u64 = cvmx_read_csr(CVMX_PEMX_CFG_RD(pcie_port));
+		return pemx_cfg_rd.s.data;
+	}
+}
+
+/**
+ * Write a PCIe config space register indirectly. This is used for
+ * registers of the form PCIEEP_CFG??? and PCIERC?_CFG???.
+ *
+ * @pcie_port:	PCIe port to write to
+ * @cfg_offset: Address to write
+ * @val:	Value to write
+ */
+static void cvmx_pcie_cfgx_write(int pcie_port, uint32_t cfg_offset,
+				 uint32_t val)
+{
+	if (octeon_has_feature(OCTEON_FEATURE_NPEI)) {
+		union cvmx_pescx_cfg_wr pescx_cfg_wr;
+		pescx_cfg_wr.u64 = 0;
+		pescx_cfg_wr.s.addr = cfg_offset;
+		pescx_cfg_wr.s.data = val;
+		cvmx_write_csr(CVMX_PESCX_CFG_WR(pcie_port), pescx_cfg_wr.u64);
+	} else {
+		union cvmx_pemx_cfg_wr pemx_cfg_wr;
+		pemx_cfg_wr.u64 = 0;
+		pemx_cfg_wr.s.addr = cfg_offset;
+		pemx_cfg_wr.s.data = val;
+		cvmx_write_csr(CVMX_PEMX_CFG_WR(pcie_port), pemx_cfg_wr.u64);
+	}
+}
+
+/**
+ * Build a PCIe config space request address for a device
+ *
+ * @pcie_port: PCIe port to access
+ * @bus:       Sub bus
+ * @dev:       Device ID
+ * @fn:	       Device sub function
+ * @reg:       Register to access
+ *
+ * Returns 64bit Octeon IO address
+ */
+static inline uint64_t __cvmx_pcie_build_config_addr(int pcie_port, int bus,
+						     int dev, int fn, int reg)
+{
+	union cvmx_pcie_address pcie_addr;
+	union cvmx_pciercx_cfg006 pciercx_cfg006;
+
+	pciercx_cfg006.u32 =
+	    cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG006(pcie_port));
+	if ((bus <= pciercx_cfg006.s.pbnum) && (dev != 0))
+		return 0;
+
+	pcie_addr.u64 = 0;
+	pcie_addr.config.upper = 2;
+	pcie_addr.config.io = 1;
+	pcie_addr.config.did = 3;
+	pcie_addr.config.subdid = 1;
+	pcie_addr.config.es = 1;
+	pcie_addr.config.port = pcie_port;
+	pcie_addr.config.ty = (bus > pciercx_cfg006.s.pbnum);
+	pcie_addr.config.bus = bus;
+	pcie_addr.config.dev = dev;
+	pcie_addr.config.func = fn;
+	pcie_addr.config.reg = reg;
+	return pcie_addr.u64;
+}
+
+/**
+ * Read 8bits from a Device's config space
+ *
+ * @pcie_port: PCIe port the device is on
+ * @bus:       Sub bus
+ * @dev:       Device ID
+ * @fn:	       Device sub function
+ * @reg:       Register to access
+ *
+ * Returns Result of the read
+ */
+static uint8_t cvmx_pcie_config_read8(int pcie_port, int bus, int dev,
+				      int fn, int reg)
+{
+	uint64_t address =
+	    __cvmx_pcie_build_config_addr(pcie_port, bus, dev, fn, reg);
+	if (address)
+		return cvmx_read64_uint8(address);
+	else
+		return 0xff;
+}
+
+/**
+ * Read 16bits from a Device's config space
+ *
+ * @pcie_port: PCIe port the device is on
+ * @bus:       Sub bus
+ * @dev:       Device ID
+ * @fn:	       Device sub function
+ * @reg:       Register to access
+ *
+ * Returns Result of the read
+ */
+static uint16_t cvmx_pcie_config_read16(int pcie_port, int bus, int dev,
+					int fn, int reg)
+{
+	uint64_t address =
+	    __cvmx_pcie_build_config_addr(pcie_port, bus, dev, fn, reg);
+	if (address)
+		return le16_to_cpu(cvmx_read64_uint16(address));
+	else
+		return 0xffff;
+}
+
+/**
+ * Read 32bits from a Device's config space
+ *
+ * @pcie_port: PCIe port the device is on
+ * @bus:       Sub bus
+ * @dev:       Device ID
+ * @fn:	       Device sub function
+ * @reg:       Register to access
+ *
+ * Returns Result of the read
+ */
+static uint32_t cvmx_pcie_config_read32(int pcie_port, int bus, int dev,
+					int fn, int reg)
+{
+	uint64_t address =
+	    __cvmx_pcie_build_config_addr(pcie_port, bus, dev, fn, reg);
+	if (address)
+		return le32_to_cpu(cvmx_read64_uint32(address));
+	else
+		return 0xffffffff;
+}
+
+/**
+ * Write 8bits to a Device's config space
+ *
+ * @pcie_port: PCIe port the device is on
+ * @bus:       Sub bus
+ * @dev:       Device ID
+ * @fn:	       Device sub function
+ * @reg:       Register to access
+ * @val:       Value to write
+ */
+static void cvmx_pcie_config_write8(int pcie_port, int bus, int dev, int fn,
+				    int reg, uint8_t val)
+{
+	uint64_t address =
+	    __cvmx_pcie_build_config_addr(pcie_port, bus, dev, fn, reg);
+	if (address)
+		cvmx_write64_uint8(address, val);
+}
+
+/**
+ * Write 16bits to a Device's config space
+ *
+ * @pcie_port: PCIe port the device is on
+ * @bus:       Sub bus
+ * @dev:       Device ID
+ * @fn:	       Device sub function
+ * @reg:       Register to access
+ * @val:       Value to write
+ */
+static void cvmx_pcie_config_write16(int pcie_port, int bus, int dev, int fn,
+				     int reg, uint16_t val)
+{
+	uint64_t address =
+	    __cvmx_pcie_build_config_addr(pcie_port, bus, dev, fn, reg);
+	if (address)
+		cvmx_write64_uint16(address, cpu_to_le16(val));
+}
+
+/**
+ * Write 32bits to a Device's config space
+ *
+ * @pcie_port: PCIe port the device is on
+ * @bus:       Sub bus
+ * @dev:       Device ID
+ * @fn:	       Device sub function
+ * @reg:       Register to access
+ * @val:       Value to write
+ */
+static void cvmx_pcie_config_write32(int pcie_port, int bus, int dev, int fn,
+				     int reg, uint32_t val)
+{
+	uint64_t address =
+	    __cvmx_pcie_build_config_addr(pcie_port, bus, dev, fn, reg);
+	if (address)
+		cvmx_write64_uint32(address, cpu_to_le32(val));
+}
+
+/**
+ * Initialize the RC config space CSRs
+ *
+ * @pcie_port: PCIe port to initialize
+ */
+static void __cvmx_pcie_rc_initialize_config_space(int pcie_port)
+{
+	union cvmx_pciercx_cfg030 pciercx_cfg030;
+	union cvmx_pciercx_cfg070 pciercx_cfg070;
+	union cvmx_pciercx_cfg001 pciercx_cfg001;
+	union cvmx_pciercx_cfg032 pciercx_cfg032;
+	union cvmx_pciercx_cfg006 pciercx_cfg006;
+	union cvmx_pciercx_cfg008 pciercx_cfg008;
+	union cvmx_pciercx_cfg009 pciercx_cfg009;
+	union cvmx_pciercx_cfg010 pciercx_cfg010;
+	union cvmx_pciercx_cfg011 pciercx_cfg011;
+	union cvmx_pciercx_cfg035 pciercx_cfg035;
+	union cvmx_pciercx_cfg075 pciercx_cfg075;
+	union cvmx_pciercx_cfg034 pciercx_cfg034;
+
+	/* Max Payload Size (PCIE*_CFG030[MPS]) */
+	/* Max Read Request Size (PCIE*_CFG030[MRRS]) */
+	/* Relaxed-order, no-snoop enables (PCIE*_CFG030[RO_EN,NS_EN] */
+	/* Error Message Enables (PCIE*_CFG030[CE_EN,NFE_EN,FE_EN,UR_EN]) */
+
+	pciercx_cfg030.u32 = cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG030(pcie_port));
+	if (OCTEON_IS_MODEL(OCTEON_CN5XXX)) {
+		pciercx_cfg030.s.mps = MPS_CN5XXX;
+		pciercx_cfg030.s.mrrs = MRRS_CN5XXX;
+	} else {
+		pciercx_cfg030.s.mps = MPS_CN6XXX;
+		pciercx_cfg030.s.mrrs = MRRS_CN6XXX;
+	}
+	/*
+	 * Enable relaxed order processing. This will allow devices to
+	 * affect read response ordering.
+	 */
+	pciercx_cfg030.s.ro_en = 1;
+	/* Enable no snoop processing. Not used by Octeon */
+	pciercx_cfg030.s.ns_en = 1;
+	/* Correctable error reporting enable. */
+	pciercx_cfg030.s.ce_en = 1;
+	/* Non-fatal error reporting enable. */
+	pciercx_cfg030.s.nfe_en = 1;
+	/* Fatal error reporting enable. */
+	pciercx_cfg030.s.fe_en = 1;
+	/* Unsupported request reporting enable. */
+	pciercx_cfg030.s.ur_en = 1;
+	cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG030(pcie_port), pciercx_cfg030.u32);
+
+
+	if (octeon_has_feature(OCTEON_FEATURE_NPEI)) {
+		union cvmx_npei_ctl_status2 npei_ctl_status2;
+		/*
+		 * Max Payload Size (NPEI_CTL_STATUS2[MPS]) must match
+		 * PCIE*_CFG030[MPS].  Max Read Request Size
+		 * (NPEI_CTL_STATUS2[MRRS]) must not exceed
+		 * PCIE*_CFG030[MRRS]
+		 */
+		npei_ctl_status2.u64 = cvmx_read_csr(CVMX_PEXP_NPEI_CTL_STATUS2);
+		/* Max payload size = 128 bytes for best Octeon DMA performance */
+		npei_ctl_status2.s.mps = MPS_CN5XXX;
+		/* Max read request size = 128 bytes for best Octeon DMA performance */
+		npei_ctl_status2.s.mrrs = MRRS_CN5XXX;
+		if (pcie_port)
+			npei_ctl_status2.s.c1_b1_s = 3; /* Port1 BAR1 Size 256MB */
+		else
+			npei_ctl_status2.s.c0_b1_s = 3; /* Port0 BAR1 Size 256MB */
+
+		cvmx_write_csr(CVMX_PEXP_NPEI_CTL_STATUS2, npei_ctl_status2.u64);
+	} else {
+		/*
+		 * Max Payload Size (DPI_SLI_PRTX_CFG[MPS]) must match
+		 * PCIE*_CFG030[MPS].  Max Read Request Size
+		 * (DPI_SLI_PRTX_CFG[MRRS]) must not exceed
+		 * PCIE*_CFG030[MRRS].
+		 */
+		union cvmx_dpi_sli_prtx_cfg prt_cfg;
+		union cvmx_sli_s2m_portx_ctl sli_s2m_portx_ctl;
+		prt_cfg.u64 = cvmx_read_csr(CVMX_DPI_SLI_PRTX_CFG(pcie_port));
+		prt_cfg.s.mps = MPS_CN6XXX;
+		prt_cfg.s.mrrs = MRRS_CN6XXX;
+		/* Max outstanding load request. */
+		prt_cfg.s.molr = 32;
+		cvmx_write_csr(CVMX_DPI_SLI_PRTX_CFG(pcie_port), prt_cfg.u64);
+
+		sli_s2m_portx_ctl.u64 = cvmx_read_csr(CVMX_PEXP_SLI_S2M_PORTX_CTL(pcie_port));
+		sli_s2m_portx_ctl.s.mrrs = MRRS_CN6XXX;
+		cvmx_write_csr(CVMX_PEXP_SLI_S2M_PORTX_CTL(pcie_port), sli_s2m_portx_ctl.u64);
+	}
+
+	/* ECRC Generation (PCIE*_CFG070[GE,CE]) */
+	pciercx_cfg070.u32 = cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG070(pcie_port));
+	pciercx_cfg070.s.ge = 1;	/* ECRC generation enable. */
+	pciercx_cfg070.s.ce = 1;	/* ECRC check enable. */
+	cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG070(pcie_port), pciercx_cfg070.u32);
+
+	/*
+	 * Access Enables (PCIE*_CFG001[MSAE,ME])
+	 * ME and MSAE should always be set.
+	 * Interrupt Disable (PCIE*_CFG001[I_DIS])
+	 * System Error Message Enable (PCIE*_CFG001[SEE])
+	 */
+	pciercx_cfg001.u32 = cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG001(pcie_port));
+	pciercx_cfg001.s.msae = 1;	/* Memory space enable. */
+	pciercx_cfg001.s.me = 1;	/* Bus master enable. */
+	pciercx_cfg001.s.i_dis = 1;	/* INTx assertion disable. */
+	pciercx_cfg001.s.see = 1;	/* SERR# enable */
+	cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG001(pcie_port), pciercx_cfg001.u32);
+
+	/* Advanced Error Recovery Message Enables */
+	/* (PCIE*_CFG066,PCIE*_CFG067,PCIE*_CFG069) */
+	cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG066(pcie_port), 0);
+	/* Use CVMX_PCIERCX_CFG067 hardware default */
+	cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG069(pcie_port), 0);
+
+
+	/* Active State Power Management (PCIE*_CFG032[ASLPC]) */
+	pciercx_cfg032.u32 = cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG032(pcie_port));
+	pciercx_cfg032.s.aslpc = 0; /* Active state Link PM control. */
+	cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG032(pcie_port), pciercx_cfg032.u32);
+
+	/*
+	 * Link Width Mode (PCIERCn_CFG452[LME]) - Set during
+	 * cvmx_pcie_rc_initialize_link()
+	 *
+	 * Primary Bus Number (PCIERCn_CFG006[PBNUM])
+	 *
+	 * We set the primary bus number to 1 so IDT bridges are
+	 * happy. They don't like zero.
+	 */
+	pciercx_cfg006.u32 = 0;
+	pciercx_cfg006.s.pbnum = 1;
+	pciercx_cfg006.s.sbnum = 1;
+	pciercx_cfg006.s.subbnum = 1;
+	cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG006(pcie_port), pciercx_cfg006.u32);
+
+
+	/*
+	 * Memory-mapped I/O BAR (PCIERCn_CFG008)
+	 * Most applications should disable the memory-mapped I/O BAR by
+	 * setting PCIERCn_CFG008[ML_ADDR] < PCIERCn_CFG008[MB_ADDR]
+	 */
+	pciercx_cfg008.u32 = 0;
+	pciercx_cfg008.s.mb_addr = 0x100;
+	pciercx_cfg008.s.ml_addr = 0;
+	cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG008(pcie_port), pciercx_cfg008.u32);
+
+
+	/*
+	 * Prefetchable BAR (PCIERCn_CFG009,PCIERCn_CFG010,PCIERCn_CFG011)
+	 * Most applications should disable the prefetchable BAR by setting
+	 * PCIERCn_CFG011[UMEM_LIMIT],PCIERCn_CFG009[LMEM_LIMIT] <
+	 * PCIERCn_CFG010[UMEM_BASE],PCIERCn_CFG009[LMEM_BASE]
+	 */
+	pciercx_cfg009.u32 = cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG009(pcie_port));
+	pciercx_cfg010.u32 = cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG010(pcie_port));
+	pciercx_cfg011.u32 = cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG011(pcie_port));
+	pciercx_cfg009.s.lmem_base = 0x100;
+	pciercx_cfg009.s.lmem_limit = 0;
+	pciercx_cfg010.s.umem_base = 0x100;
+	pciercx_cfg011.s.umem_limit = 0;
+	cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG009(pcie_port), pciercx_cfg009.u32);
+	cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG010(pcie_port), pciercx_cfg010.u32);
+	cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG011(pcie_port), pciercx_cfg011.u32);
+
+	/*
+	 * System Error Interrupt Enables (PCIERCn_CFG035[SECEE,SEFEE,SENFEE])
+	 * PME Interrupt Enables (PCIERCn_CFG035[PMEIE])
+	*/
+	pciercx_cfg035.u32 = cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG035(pcie_port));
+	pciercx_cfg035.s.secee = 1; /* System error on correctable error enable. */
+	pciercx_cfg035.s.sefee = 1; /* System error on fatal error enable. */
+	pciercx_cfg035.s.senfee = 1; /* System error on non-fatal error enable. */
+	pciercx_cfg035.s.pmeie = 1; /* PME interrupt enable. */
+	cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG035(pcie_port), pciercx_cfg035.u32);
+
+	/*
+	 * Advanced Error Recovery Interrupt Enables
+	 * (PCIERCn_CFG075[CERE,NFERE,FERE])
+	 */
+	pciercx_cfg075.u32 = cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG075(pcie_port));
+	pciercx_cfg075.s.cere = 1; /* Correctable error reporting enable. */
+	pciercx_cfg075.s.nfere = 1; /* Non-fatal error reporting enable. */
+	pciercx_cfg075.s.fere = 1; /* Fatal error reporting enable. */
+	cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG075(pcie_port), pciercx_cfg075.u32);
+
+	/*
+	 * HP Interrupt Enables (PCIERCn_CFG034[HPINT_EN],
+	 * PCIERCn_CFG034[DLLS_EN,CCINT_EN])
+	 */
+	pciercx_cfg034.u32 = cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG034(pcie_port));
+	pciercx_cfg034.s.hpint_en = 1; /* Hot-plug interrupt enable. */
+	pciercx_cfg034.s.dlls_en = 1; /* Data Link Layer state changed enable */
+	pciercx_cfg034.s.ccint_en = 1; /* Command completed interrupt enable. */
+	cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG034(pcie_port), pciercx_cfg034.u32);
+}
+
+/**
+ * Initialize a host mode PCIe gen 1 link. This function takes a PCIe
+ * port from reset to a link up state. Software can then begin
+ * configuring the rest of the link.
+ *
+ * @pcie_port: PCIe port to initialize
+ *
+ * Returns Zero on success
+ */
+static int __cvmx_pcie_rc_initialize_link_gen1(int pcie_port)
+{
+	uint64_t start_cycle;
+	union cvmx_pescx_ctl_status pescx_ctl_status;
+	union cvmx_pciercx_cfg452 pciercx_cfg452;
+	union cvmx_pciercx_cfg032 pciercx_cfg032;
+	union cvmx_pciercx_cfg448 pciercx_cfg448;
+
+	/* Set the lane width */
+	pciercx_cfg452.u32 = cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG452(pcie_port));
+	pescx_ctl_status.u64 = cvmx_read_csr(CVMX_PESCX_CTL_STATUS(pcie_port));
+	if (pescx_ctl_status.s.qlm_cfg == 0)
+		/* We're in 8 lane (56XX) or 4 lane (54XX) mode */
+		pciercx_cfg452.s.lme = 0xf;
+	else
+		/* We're in 4 lane (56XX) or 2 lane (52XX) mode */
+		pciercx_cfg452.s.lme = 0x7;
+	cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG452(pcie_port), pciercx_cfg452.u32);
+
+	/*
+	 * CN52XX pass 1.x has an errata where length mismatches on UR
+	 * responses can cause bus errors on 64bit memory
+	 * reads. Turning off length error checking fixes this.
+	 */
+	if (OCTEON_IS_MODEL(OCTEON_CN52XX_PASS1_X)) {
+		union cvmx_pciercx_cfg455 pciercx_cfg455;
+		pciercx_cfg455.u32 = cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG455(pcie_port));
+		pciercx_cfg455.s.m_cpl_len_err = 1;
+		cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG455(pcie_port), pciercx_cfg455.u32);
+	}
+
+	/* Lane swap needs to be manually enabled for CN52XX */
+	if (OCTEON_IS_MODEL(OCTEON_CN52XX) && (pcie_port == 1)) {
+		pescx_ctl_status.s.lane_swp = 1;
+		cvmx_write_csr(CVMX_PESCX_CTL_STATUS(pcie_port), pescx_ctl_status.u64);
+	}
+
+	/* Bring up the link */
+	pescx_ctl_status.u64 = cvmx_read_csr(CVMX_PESCX_CTL_STATUS(pcie_port));
+	pescx_ctl_status.s.lnk_enb = 1;
+	cvmx_write_csr(CVMX_PESCX_CTL_STATUS(pcie_port), pescx_ctl_status.u64);
+
+	/*
+	 * CN52XX pass 1.0: Due to a bug in 2nd order CDR, it needs to
+	 * be disabled.
+	 */
+	if (OCTEON_IS_MODEL(OCTEON_CN52XX_PASS1_0))
+		__cvmx_helper_errata_qlm_disable_2nd_order_cdr(0);
+
+	/* Wait for the link to come up */
+	start_cycle = cvmx_get_cycle();
+	do {
+		if (cvmx_get_cycle() - start_cycle > 2 * octeon_get_clock_rate()) {
+			cvmx_dprintf("PCIe: Port %d link timeout\n", pcie_port);
+			return -1;
+		}
+		__delay(10000);
+		pciercx_cfg032.u32 = cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG032(pcie_port));
+	} while (pciercx_cfg032.s.dlla == 0);
+
+	/* Clear all pending errors */
+	cvmx_write_csr(CVMX_PEXP_NPEI_INT_SUM, cvmx_read_csr(CVMX_PEXP_NPEI_INT_SUM));
+
+	/*
+	 * Update the Replay Time Limit. Empirically, some PCIe
+	 * devices take a little longer to respond than expected under
+	 * load. As a workaround for this we configure the Replay Time
+	 * Limit to the value expected for a 512 byte MPS instead of
+	 * our actual 256 byte MPS. The numbers below are directly
+	 * from the PCIe spec table 3-4.
+	 */
+	pciercx_cfg448.u32 = cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG448(pcie_port));
+	switch (pciercx_cfg032.s.nlw) {
+	case 1:		/* 1 lane */
+		pciercx_cfg448.s.rtl = 1677;
+		break;
+	case 2:		/* 2 lanes */
+		pciercx_cfg448.s.rtl = 867;
+		break;
+	case 4:		/* 4 lanes */
+		pciercx_cfg448.s.rtl = 462;
+		break;
+	case 8:		/* 8 lanes */
+		pciercx_cfg448.s.rtl = 258;
+		break;
+	}
+	cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG448(pcie_port), pciercx_cfg448.u32);
+
+	return 0;
+}
+
+static void __cvmx_increment_ba(union cvmx_sli_mem_access_subidx *pmas)
+{
+	if (OCTEON_IS_MODEL(OCTEON_CN68XX))
+		pmas->cn68xx.ba++;
+	else
+		pmas->s.ba++;
+}
+
+/**
+ * Initialize a PCIe gen 1 port for use in host(RC) mode. It doesn't
+ * enumerate the bus.
+ *
+ * @pcie_port: PCIe port to initialize
+ *
+ * Returns Zero on success
+ */
+static int __cvmx_pcie_rc_initialize_gen1(int pcie_port)
+{
+	int i;
+	int base;
+	u64 addr_swizzle;
+	union cvmx_ciu_soft_prst ciu_soft_prst;
+	union cvmx_pescx_bist_status pescx_bist_status;
+	union cvmx_pescx_bist_status2 pescx_bist_status2;
+	union cvmx_npei_ctl_status npei_ctl_status;
+	union cvmx_npei_mem_access_ctl npei_mem_access_ctl;
+	union cvmx_npei_mem_access_subidx mem_access_subid;
+	union cvmx_npei_dbg_data npei_dbg_data;
+	union cvmx_pescx_ctl_status2 pescx_ctl_status2;
+	union cvmx_pciercx_cfg032 pciercx_cfg032;
+	union cvmx_npei_bar1_indexx bar1_index;
+
+retry:
+	/*
+	 * Make sure we aren't trying to setup a target mode interface
+	 * in host mode.
+	 */
+	npei_ctl_status.u64 = cvmx_read_csr(CVMX_PEXP_NPEI_CTL_STATUS);
+	if ((pcie_port == 0) && !npei_ctl_status.s.host_mode) {
+		cvmx_dprintf("PCIe: Port %d in endpoint mode\n", pcie_port);
+		return -1;
+	}
+
+	/*
+	 * Make sure a CN52XX isn't trying to bring up port 1 when it
+	 * is disabled.
+	 */
+	if (OCTEON_IS_MODEL(OCTEON_CN52XX)) {
+		npei_dbg_data.u64 = cvmx_read_csr(CVMX_PEXP_NPEI_DBG_DATA);
+		if ((pcie_port == 1) && npei_dbg_data.cn52xx.qlm0_link_width) {
+			cvmx_dprintf("PCIe: ERROR: cvmx_pcie_rc_initialize() called on port1, but port1 is disabled\n");
+			return -1;
+		}
+	}
+
+	/*
+	 * PCIe switch arbitration mode. '0' == fixed priority NPEI,
+	 * PCIe0, then PCIe1. '1' == round robin.
+	 */
+	npei_ctl_status.s.arb = 1;
+	/* Allow up to 0x20 config retries */
+	npei_ctl_status.s.cfg_rtry = 0x20;
+	/*
+	 * CN52XX pass1.x has an errata where P0_NTAGS and P1_NTAGS
+	 * don't reset.
+	 */
+	if (OCTEON_IS_MODEL(OCTEON_CN52XX_PASS1_X)) {
+		npei_ctl_status.s.p0_ntags = 0x20;
+		npei_ctl_status.s.p1_ntags = 0x20;
+	}
+	cvmx_write_csr(CVMX_PEXP_NPEI_CTL_STATUS, npei_ctl_status.u64);
+
+	/* Bring the PCIe out of reset */
+	if (cvmx_sysinfo_get()->board_type == CVMX_BOARD_TYPE_EBH5200) {
+		/*
+		 * The EBH5200 board swapped the PCIe reset lines on
+		 * the board. As a workaround for this bug, we bring
+		 * both PCIe ports out of reset at the same time
+		 * instead of on separate calls. So for port 0, we
+		 * bring both out of reset and do nothing on port 1
+		 */
+		if (pcie_port == 0) {
+			ciu_soft_prst.u64 = cvmx_read_csr(CVMX_CIU_SOFT_PRST);
+			/*
+			 * After a chip reset the PCIe will also be in
+			 * reset. If it isn't, most likely someone is
+			 * trying to init it again without a proper
+			 * PCIe reset.
+			 */
+			if (ciu_soft_prst.s.soft_prst == 0) {
+				/* Reset the ports */
+				ciu_soft_prst.s.soft_prst = 1;
+				cvmx_write_csr(CVMX_CIU_SOFT_PRST, ciu_soft_prst.u64);
+				ciu_soft_prst.u64 = cvmx_read_csr(CVMX_CIU_SOFT_PRST1);
+				ciu_soft_prst.s.soft_prst = 1;
+				cvmx_write_csr(CVMX_CIU_SOFT_PRST1, ciu_soft_prst.u64);
+				/* Wait until pcie resets the ports. */
+				udelay(2000);
+			}
+			ciu_soft_prst.u64 = cvmx_read_csr(CVMX_CIU_SOFT_PRST1);
+			ciu_soft_prst.s.soft_prst = 0;
+			cvmx_write_csr(CVMX_CIU_SOFT_PRST1, ciu_soft_prst.u64);
+			ciu_soft_prst.u64 = cvmx_read_csr(CVMX_CIU_SOFT_PRST);
+			ciu_soft_prst.s.soft_prst = 0;
+			cvmx_write_csr(CVMX_CIU_SOFT_PRST, ciu_soft_prst.u64);
+		}
+	} else {
+		/*
+		 * The normal case: The PCIe ports are completely
+		 * separate and can be brought out of reset
+		 * independently.
+		 */
+		if (pcie_port)
+			ciu_soft_prst.u64 = cvmx_read_csr(CVMX_CIU_SOFT_PRST1);
+		else
+			ciu_soft_prst.u64 = cvmx_read_csr(CVMX_CIU_SOFT_PRST);
+		/*
+		 * After a chip reset the PCIe will also be in
+		 * reset. If it isn't, most likely someone is trying
+		 * to init it again without a proper PCIe reset.
+		 */
+		if (ciu_soft_prst.s.soft_prst == 0) {
+			/* Reset the port */
+			ciu_soft_prst.s.soft_prst = 1;
+			if (pcie_port)
+				cvmx_write_csr(CVMX_CIU_SOFT_PRST1, ciu_soft_prst.u64);
+			else
+				cvmx_write_csr(CVMX_CIU_SOFT_PRST, ciu_soft_prst.u64);
+			/* Wait until pcie resets the ports. */
+			udelay(2000);
+		}
+		if (pcie_port) {
+			ciu_soft_prst.u64 = cvmx_read_csr(CVMX_CIU_SOFT_PRST1);
+			ciu_soft_prst.s.soft_prst = 0;
+			cvmx_write_csr(CVMX_CIU_SOFT_PRST1, ciu_soft_prst.u64);
+		} else {
+			ciu_soft_prst.u64 = cvmx_read_csr(CVMX_CIU_SOFT_PRST);
+			ciu_soft_prst.s.soft_prst = 0;
+			cvmx_write_csr(CVMX_CIU_SOFT_PRST, ciu_soft_prst.u64);
+		}
+	}
+
+	/*
+	 * Wait for PCIe reset to complete. Due to errata PCIE-700, we
+	 * don't poll PESCX_CTL_STATUS2[PCIERST], but simply wait a
+	 * fixed number of cycles.
+	 */
+	__delay(400000);
+
+	/*
+	 * PESCX_BIST_STATUS2[PCLK_RUN] was missing on pass 1 of
+	 * CN56XX and CN52XX, so we only probe it on newer chips
+	 */
+	if (!OCTEON_IS_MODEL(OCTEON_CN56XX_PASS1_X) && !OCTEON_IS_MODEL(OCTEON_CN52XX_PASS1_X)) {
+		/* Clear PCLK_RUN so we can check if the clock is running */
+		pescx_ctl_status2.u64 = cvmx_read_csr(CVMX_PESCX_CTL_STATUS2(pcie_port));
+		pescx_ctl_status2.s.pclk_run = 1;
+		cvmx_write_csr(CVMX_PESCX_CTL_STATUS2(pcie_port), pescx_ctl_status2.u64);
+		/* Now that we cleared PCLK_RUN, wait for it to be set
+		 * again telling us the clock is running
+		 */
+		if (CVMX_WAIT_FOR_FIELD64(CVMX_PESCX_CTL_STATUS2(pcie_port),
+					  union cvmx_pescx_ctl_status2, pclk_run, ==, 1, 10000)) {
+			cvmx_dprintf("PCIe: Port %d isn't clocked, skipping.\n", pcie_port);
+			return -1;
+		}
+	}
+
+	/*
+	 * Check and make sure PCIe came out of reset. If it doesn't
+	 * the board probably hasn't wired the clocks up and the
+	 * interface should be skipped.
+	 */
+	pescx_ctl_status2.u64 = cvmx_read_csr(CVMX_PESCX_CTL_STATUS2(pcie_port));
+	if (pescx_ctl_status2.s.pcierst) {
+		cvmx_dprintf("PCIe: Port %d stuck in reset, skipping.\n", pcie_port);
+		return -1;
+	}
+
+	/*
+	 * Check BIST2 status. If any bits are set skip this
+	 * interface. This is an attempt to catch PCIE-813 on pass 1
+	 * parts.
+	 */
+	pescx_bist_status2.u64 = cvmx_read_csr(CVMX_PESCX_BIST_STATUS2(pcie_port));
+	if (pescx_bist_status2.u64) {
+		cvmx_dprintf("PCIe: Port %d BIST2 failed. Most likely this port isn't hooked up, skipping.\n",
+			     pcie_port);
+		return -1;
+	}
+
+	/* Check BIST status */
+	pescx_bist_status.u64 = cvmx_read_csr(CVMX_PESCX_BIST_STATUS(pcie_port));
+	if (pescx_bist_status.u64)
+		cvmx_dprintf("PCIe: BIST FAILED for port %d (0x%016llx)\n",
+			     pcie_port, CAST64(pescx_bist_status.u64));
+
+	/* Initialize the config space CSRs */
+	__cvmx_pcie_rc_initialize_config_space(pcie_port);
+
+	/* Bring the link up */
+	if (__cvmx_pcie_rc_initialize_link_gen1(pcie_port)) {
+		cvmx_dprintf("PCIe: Failed to initialize port %d, probably the slot is empty\n",
+			     pcie_port);
+		return -1;
+	}
+
+	/* Store merge control (NPEI_MEM_ACCESS_CTL[TIMER,MAX_WORD]) */
+	npei_mem_access_ctl.u64 = cvmx_read_csr(CVMX_PEXP_NPEI_MEM_ACCESS_CTL);
+	npei_mem_access_ctl.s.max_word = 0;	/* Allow 16 words to combine */
+	npei_mem_access_ctl.s.timer = 127;	/* Wait up to 127 cycles for more data */
+	cvmx_write_csr(CVMX_PEXP_NPEI_MEM_ACCESS_CTL, npei_mem_access_ctl.u64);
+
+	/* Setup Mem access SubDIDs */
+	mem_access_subid.u64 = 0;
+	mem_access_subid.s.port = pcie_port; /* Port the request is sent to. */
+	mem_access_subid.s.nmerge = 1;	/* Due to an errata on pass 1 chips, no merging is allowed. */
+	mem_access_subid.s.esr = 1;	/* Endian-swap for Reads. */
+	mem_access_subid.s.esw = 1;	/* Endian-swap for Writes. */
+	mem_access_subid.s.nsr = 0;	/* Enable Snooping for Reads. Octeon doesn't care, but devices might want this more conservative setting */
+	mem_access_subid.s.nsw = 0;	/* Enable Snoop for Writes. */
+	mem_access_subid.s.ror = 0;	/* Disable Relaxed Ordering for Reads. */
+	mem_access_subid.s.row = 0;	/* Disable Relaxed Ordering for Writes. */
+	mem_access_subid.s.ba = 0;	/* PCIe Address Bits <63:34>. */
+
+	/*
+	 * Setup mem access 12-15 for port 0, 16-19 for port 1,
+	 * supplying 36 bits of address space.
+	 */
+	for (i = 12 + pcie_port * 4; i < 16 + pcie_port * 4; i++) {
+		cvmx_write_csr(CVMX_PEXP_NPEI_MEM_ACCESS_SUBIDX(i), mem_access_subid.u64);
+		mem_access_subid.s.ba += 1; /* Set each SUBID to extend the addressable range */
+	}
+
+	/*
+	 * Disable the peer to peer forwarding register. This must be
+	 * setup by the OS after it enumerates the bus and assigns
+	 * addresses to the PCIe busses.
+	 */
+	for (i = 0; i < 4; i++) {
+		cvmx_write_csr(CVMX_PESCX_P2P_BARX_START(i, pcie_port), -1);
+		cvmx_write_csr(CVMX_PESCX_P2P_BARX_END(i, pcie_port), -1);
+	}
+
+	/* Set Octeon's BAR0 to decode 0-16KB. It overlaps with Bar2 */
+	cvmx_write_csr(CVMX_PESCX_P2N_BAR0_START(pcie_port), 0);
+
+	/* BAR1 follows BAR2 with a gap so it has the same address as for gen2. */
+	cvmx_write_csr(CVMX_PESCX_P2N_BAR1_START(pcie_port), CVMX_PCIE_BAR1_RC_BASE);
+
+	bar1_index.u32 = 0;
+	bar1_index.s.addr_idx = (CVMX_PCIE_BAR1_PHYS_BASE >> 22);
+	bar1_index.s.ca = 1;	   /* Not Cached */
+	bar1_index.s.end_swp = 1;  /* Endian Swap mode */
+	bar1_index.s.addr_v = 1;   /* Valid entry */
+
+	base = pcie_port ? 16 : 0;
+
+	/* Big endian swizzle for 32-bit PEXP_NCB register. */
+#ifdef __MIPSEB__
+	addr_swizzle = 4;
+#else
+	addr_swizzle = 0;
+#endif
+	for (i = 0; i < 16; i++) {
+		cvmx_write64_uint32((CVMX_PEXP_NPEI_BAR1_INDEXX(base) ^ addr_swizzle),
+				    bar1_index.u32);
+		base++;
+		/* 256MB / 16 >> 22 == 4 */
+		bar1_index.s.addr_idx += (((1ull << 28) / 16ull) >> 22);
+	}
+
+	/*
+	 * Set Octeon's BAR2 to decode 0-2^39. Bar0 and Bar1 take
+	 * precedence where they overlap. It also overlaps with the
+	 * device addresses, so make sure the peer to peer forwarding
+	 * is set right.
+	 */
+	cvmx_write_csr(CVMX_PESCX_P2N_BAR2_START(pcie_port), 0);
+
+	/*
+	 * Setup BAR2 attributes
+	 *
+	 * Relaxed Ordering (NPEI_CTL_PORTn[PTLP_RO,CTLP_RO, WAIT_COM])
+	 * - PTLP_RO,CTLP_RO should normally be set (except for debug).
+	 * - WAIT_COM=0 will likely work for all applications.
+	 *
+	 * Load completion relaxed ordering (NPEI_CTL_PORTn[WAITL_COM]).
+	 */
+	if (pcie_port) {
+		union cvmx_npei_ctl_port1 npei_ctl_port;
+		npei_ctl_port.u64 = cvmx_read_csr(CVMX_PEXP_NPEI_CTL_PORT1);
+		npei_ctl_port.s.bar2_enb = 1;
+		npei_ctl_port.s.bar2_esx = 1;
+		npei_ctl_port.s.bar2_cax = 0;
+		npei_ctl_port.s.ptlp_ro = 1;
+		npei_ctl_port.s.ctlp_ro = 1;
+		npei_ctl_port.s.wait_com = 0;
+		npei_ctl_port.s.waitl_com = 0;
+		cvmx_write_csr(CVMX_PEXP_NPEI_CTL_PORT1, npei_ctl_port.u64);
+	} else {
+		union cvmx_npei_ctl_port0 npei_ctl_port;
+		npei_ctl_port.u64 = cvmx_read_csr(CVMX_PEXP_NPEI_CTL_PORT0);
+		npei_ctl_port.s.bar2_enb = 1;
+		npei_ctl_port.s.bar2_esx = 1;
+		npei_ctl_port.s.bar2_cax = 0;
+		npei_ctl_port.s.ptlp_ro = 1;
+		npei_ctl_port.s.ctlp_ro = 1;
+		npei_ctl_port.s.wait_com = 0;
+		npei_ctl_port.s.waitl_com = 0;
+		cvmx_write_csr(CVMX_PEXP_NPEI_CTL_PORT0, npei_ctl_port.u64);
+	}
+
+	/*
+	 * Both pass 1 and pass 2 of CN52XX and CN56XX have an errata
+	 * that causes TLP ordering to not be preserved after multiple
+	 * PCIe port resets. This code detects this fault and corrects
+	 * it by aligning the TLP counters properly. Another link
+	 * reset is then performed. See PCIE-13340
+	 */
+	if (OCTEON_IS_MODEL(OCTEON_CN56XX_PASS2_X) ||
+	    OCTEON_IS_MODEL(OCTEON_CN52XX_PASS2_X) ||
+	    OCTEON_IS_MODEL(OCTEON_CN56XX_PASS1_X) ||
+	    OCTEON_IS_MODEL(OCTEON_CN52XX_PASS1_X)) {
+		union cvmx_npei_dbg_data dbg_data;
+		int old_in_fif_p_count;
+		int in_fif_p_count;
+		int out_p_count;
+		int in_p_offset = (OCTEON_IS_MODEL(OCTEON_CN52XX_PASS1_X) || OCTEON_IS_MODEL(OCTEON_CN56XX_PASS1_X)) ? 4 : 1;
+		int i;
+
+		/*
+		 * Choose a write address of 1MB. It should be
+		 * harmless as all bars haven't been setup.
+		 */
+		uint64_t write_address = (cvmx_pcie_get_mem_base_address(pcie_port) + 0x100000) | (1ull<<63);
+
+		/*
+		 * Make sure at least in_p_offset have been executed before we try and
+		 * read in_fif_p_count
+		 */
+		i = in_p_offset;
+		while (i--) {
+			cvmx_write64_uint32(write_address, 0);
+			__delay(10000);
+		}
+
+		/*
+		 * Read the IN_FIF_P_COUNT from the debug
+		 * select. IN_FIF_P_COUNT can be unstable sometimes so
+		 * read it twice with a write between the reads.  This
+		 * way we can tell the value is good as it will
+		 * increment by one due to the write
+		 */
+		cvmx_write_csr(CVMX_PEXP_NPEI_DBG_SELECT, (pcie_port) ? 0xd7fc : 0xcffc);
+		cvmx_read_csr(CVMX_PEXP_NPEI_DBG_SELECT);
+		do {
+			dbg_data.u64 = cvmx_read_csr(CVMX_PEXP_NPEI_DBG_DATA);
+			old_in_fif_p_count = dbg_data.s.data & 0xff;
+			cvmx_write64_uint32(write_address, 0);
+			__delay(10000);
+			dbg_data.u64 = cvmx_read_csr(CVMX_PEXP_NPEI_DBG_DATA);
+			in_fif_p_count = dbg_data.s.data & 0xff;
+		} while (in_fif_p_count != ((old_in_fif_p_count+1) & 0xff));
+
+		/* Update in_fif_p_count for it's offset with respect to out_p_count */
+		in_fif_p_count = (in_fif_p_count + in_p_offset) & 0xff;
+
+		/* Read the OUT_P_COUNT from the debug select */
+		cvmx_write_csr(CVMX_PEXP_NPEI_DBG_SELECT, (pcie_port) ? 0xd00f : 0xc80f);
+		cvmx_read_csr(CVMX_PEXP_NPEI_DBG_SELECT);
+		dbg_data.u64 = cvmx_read_csr(CVMX_PEXP_NPEI_DBG_DATA);
+		out_p_count = (dbg_data.s.data>>1) & 0xff;
+
+		/* Check that the two counters are aligned */
+		if (out_p_count != in_fif_p_count) {
+			cvmx_dprintf("PCIe: Port %d aligning TLP counters as workaround to maintain ordering\n", pcie_port);
+			while (in_fif_p_count != 0) {
+				cvmx_write64_uint32(write_address, 0);
+				__delay(10000);
+				in_fif_p_count = (in_fif_p_count + 1) & 0xff;
+			}
+			/*
+			 * The EBH5200 board swapped the PCIe reset
+			 * lines on the board. This means we must
+			 * bring both links down and up, which will
+			 * cause the PCIe0 to need alignment
+			 * again. Lots of messages will be displayed,
+			 * but everything should work
+			 */
+			if ((cvmx_sysinfo_get()->board_type == CVMX_BOARD_TYPE_EBH5200) &&
+				(pcie_port == 1))
+				cvmx_pcie_rc_initialize(0);
+			/* Rety bringing this port up */
+			goto retry;
+		}
+	}
+
+	/* Display the link status */
+	pciercx_cfg032.u32 = cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG032(pcie_port));
+	cvmx_dprintf("PCIe: Port %d link active, %d lanes\n", pcie_port, pciercx_cfg032.s.nlw);
+
+	return 0;
+}
+
+/**
+  * Initialize a host mode PCIe gen 2 link. This function takes a PCIe
+ * port from reset to a link up state. Software can then begin
+ * configuring the rest of the link.
+ *
+ * @pcie_port: PCIe port to initialize
+ *
+ * Return Zero on success.
+ */
+static int __cvmx_pcie_rc_initialize_link_gen2(int pcie_port)
+{
+	uint64_t start_cycle;
+	union cvmx_pemx_ctl_status pem_ctl_status;
+	union cvmx_pciercx_cfg032 pciercx_cfg032;
+	union cvmx_pciercx_cfg448 pciercx_cfg448;
+
+	/* Bring up the link */
+	pem_ctl_status.u64 = cvmx_read_csr(CVMX_PEMX_CTL_STATUS(pcie_port));
+	pem_ctl_status.s.lnk_enb = 1;
+	cvmx_write_csr(CVMX_PEMX_CTL_STATUS(pcie_port), pem_ctl_status.u64);
+
+	/* Wait for the link to come up */
+	start_cycle = cvmx_get_cycle();
+	do {
+		if (cvmx_get_cycle() - start_cycle >  octeon_get_clock_rate())
+			return -1;
+		__delay(10000);
+		pciercx_cfg032.u32 = cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG032(pcie_port));
+	} while ((pciercx_cfg032.s.dlla == 0) || (pciercx_cfg032.s.lt == 1));
+
+	/*
+	 * Update the Replay Time Limit. Empirically, some PCIe
+	 * devices take a little longer to respond than expected under
+	 * load. As a workaround for this we configure the Replay Time
+	 * Limit to the value expected for a 512 byte MPS instead of
+	 * our actual 256 byte MPS. The numbers below are directly
+	 * from the PCIe spec table 3-4
+	 */
+	pciercx_cfg448.u32 = cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG448(pcie_port));
+	switch (pciercx_cfg032.s.nlw) {
+	case 1: /* 1 lane */
+		pciercx_cfg448.s.rtl = 1677;
+		break;
+	case 2: /* 2 lanes */
+		pciercx_cfg448.s.rtl = 867;
+		break;
+	case 4: /* 4 lanes */
+		pciercx_cfg448.s.rtl = 462;
+		break;
+	case 8: /* 8 lanes */
+		pciercx_cfg448.s.rtl = 258;
+		break;
+	}
+	cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG448(pcie_port), pciercx_cfg448.u32);
+
+	return 0;
+}
+
+
+/**
+ * Initialize a PCIe gen 2 port for use in host(RC) mode. It doesn't enumerate
+ * the bus.
+ *
+ * @pcie_port: PCIe port to initialize
+ *
+ * Returns Zero on success.
+ */
+static int __cvmx_pcie_rc_initialize_gen2(int pcie_port)
+{
+	int i;
+	union cvmx_ciu_soft_prst ciu_soft_prst;
+	union cvmx_mio_rst_ctlx mio_rst_ctl;
+	union cvmx_pemx_bar_ctl pemx_bar_ctl;
+	union cvmx_pemx_ctl_status pemx_ctl_status;
+	union cvmx_pemx_bist_status pemx_bist_status;
+	union cvmx_pemx_bist_status2 pemx_bist_status2;
+	union cvmx_pciercx_cfg032 pciercx_cfg032;
+	union cvmx_pciercx_cfg515 pciercx_cfg515;
+	union cvmx_sli_ctl_portx sli_ctl_portx;
+	union cvmx_sli_mem_access_ctl sli_mem_access_ctl;
+	union cvmx_sli_mem_access_subidx mem_access_subid;
+	union cvmx_sriox_status_reg sriox_status_reg;
+	union cvmx_pemx_bar1_indexx bar1_index;
+
+	if (octeon_has_feature(OCTEON_FEATURE_SRIO)) {
+		/* Make sure this interface isn't SRIO */
+		if (OCTEON_IS_MODEL(OCTEON_CN66XX)) {
+			/*
+			 * The CN66XX requires reading the
+			 * MIO_QLMX_CFG register to figure out the
+			 * port type.
+			 */
+			union cvmx_mio_qlmx_cfg qlmx_cfg;
+			qlmx_cfg.u64 = cvmx_read_csr(CVMX_MIO_QLMX_CFG(pcie_port));
+
+			if (qlmx_cfg.s.qlm_spd == 15) {
+				pr_notice("PCIe: Port %d is disabled, skipping.\n", pcie_port);
+				return -1;
+			}
+
+			switch (qlmx_cfg.s.qlm_spd) {
+			case 0x1: /* SRIO 1x4 short */
+			case 0x3: /* SRIO 1x4 long */
+			case 0x4: /* SRIO 2x2 short */
+			case 0x6: /* SRIO 2x2 long */
+				pr_notice("PCIe: Port %d is SRIO, skipping.\n", pcie_port);
+				return -1;
+			case 0x9: /* SGMII */
+				pr_notice("PCIe: Port %d is SGMII, skipping.\n", pcie_port);
+				return -1;
+			case 0xb: /* XAUI */
+				pr_notice("PCIe: Port %d is XAUI, skipping.\n", pcie_port);
+				return -1;
+			case 0x0: /* PCIE gen2 */
+			case 0x8: /* PCIE gen2 (alias) */
+			case 0x2: /* PCIE gen1 */
+			case 0xa: /* PCIE gen1 (alias) */
+				break;
+			default:
+				pr_notice("PCIe: Port %d is unknown, skipping.\n", pcie_port);
+				return -1;
+			}
+		} else {
+			sriox_status_reg.u64 = cvmx_read_csr(CVMX_SRIOX_STATUS_REG(pcie_port));
+			if (sriox_status_reg.s.srio) {
+				pr_notice("PCIe: Port %d is SRIO, skipping.\n", pcie_port);
+				return -1;
+			}
+		}
+	}
+
+#if 0
+    /* This code is so that the PCIe analyzer is able to see 63XX traffic */
+	pr_notice("PCIE : init for pcie analyzer.\n");
+	cvmx_helper_qlm_jtag_init();
+	cvmx_helper_qlm_jtag_shift_zeros(pcie_port, 85);
+	cvmx_helper_qlm_jtag_shift(pcie_port, 1, 1);
+	cvmx_helper_qlm_jtag_shift_zeros(pcie_port, 300-86);
+	cvmx_helper_qlm_jtag_shift_zeros(pcie_port, 85);
+	cvmx_helper_qlm_jtag_shift(pcie_port, 1, 1);
+	cvmx_helper_qlm_jtag_shift_zeros(pcie_port, 300-86);
+	cvmx_helper_qlm_jtag_shift_zeros(pcie_port, 85);
+	cvmx_helper_qlm_jtag_shift(pcie_port, 1, 1);
+	cvmx_helper_qlm_jtag_shift_zeros(pcie_port, 300-86);
+	cvmx_helper_qlm_jtag_shift_zeros(pcie_port, 85);
+	cvmx_helper_qlm_jtag_shift(pcie_port, 1, 1);
+	cvmx_helper_qlm_jtag_shift_zeros(pcie_port, 300-86);
+	cvmx_helper_qlm_jtag_update(pcie_port);
+#endif
+
+	/* Make sure we aren't trying to setup a target mode interface in host mode */
+	mio_rst_ctl.u64 = cvmx_read_csr(CVMX_MIO_RST_CTLX(pcie_port));
+	if (!mio_rst_ctl.s.host_mode) {
+		pr_notice("PCIe: Port %d in endpoint mode.\n", pcie_port);
+		return -1;
+	}
+
+	/* CN63XX Pass 1.0 errata G-14395 requires the QLM De-emphasis be programmed */
+	if (OCTEON_IS_MODEL(OCTEON_CN63XX_PASS1_0)) {
+		if (pcie_port) {
+			union cvmx_ciu_qlm ciu_qlm;
+			ciu_qlm.u64 = cvmx_read_csr(CVMX_CIU_QLM1);
+			ciu_qlm.s.txbypass = 1;
+			ciu_qlm.s.txdeemph = 5;
+			ciu_qlm.s.txmargin = 0x17;
+			cvmx_write_csr(CVMX_CIU_QLM1, ciu_qlm.u64);
+		} else {
+			union cvmx_ciu_qlm ciu_qlm;
+			ciu_qlm.u64 = cvmx_read_csr(CVMX_CIU_QLM0);
+			ciu_qlm.s.txbypass = 1;
+			ciu_qlm.s.txdeemph = 5;
+			ciu_qlm.s.txmargin = 0x17;
+			cvmx_write_csr(CVMX_CIU_QLM0, ciu_qlm.u64);
+		}
+	}
+	/* Bring the PCIe out of reset */
+	if (pcie_port)
+		ciu_soft_prst.u64 = cvmx_read_csr(CVMX_CIU_SOFT_PRST1);
+	else
+		ciu_soft_prst.u64 = cvmx_read_csr(CVMX_CIU_SOFT_PRST);
+	/*
+	 * After a chip reset the PCIe will also be in reset. If it
+	 * isn't, most likely someone is trying to init it again
+	 * without a proper PCIe reset
+	 */
+	if (ciu_soft_prst.s.soft_prst == 0) {
+		/* Reset the port */
+		ciu_soft_prst.s.soft_prst = 1;
+		if (pcie_port)
+			cvmx_write_csr(CVMX_CIU_SOFT_PRST1, ciu_soft_prst.u64);
+		else
+			cvmx_write_csr(CVMX_CIU_SOFT_PRST, ciu_soft_prst.u64);
+		/* Wait until pcie resets the ports. */
+		udelay(2000);
+	}
+	if (pcie_port) {
+		ciu_soft_prst.u64 = cvmx_read_csr(CVMX_CIU_SOFT_PRST1);
+		ciu_soft_prst.s.soft_prst = 0;
+		cvmx_write_csr(CVMX_CIU_SOFT_PRST1, ciu_soft_prst.u64);
+	} else {
+		ciu_soft_prst.u64 = cvmx_read_csr(CVMX_CIU_SOFT_PRST);
+		ciu_soft_prst.s.soft_prst = 0;
+		cvmx_write_csr(CVMX_CIU_SOFT_PRST, ciu_soft_prst.u64);
+	}
+
+	/* Wait for PCIe reset to complete */
+	udelay(1000);
+
+	/*
+	 * Check and make sure PCIe came out of reset. If it doesn't
+	 * the board probably hasn't wired the clocks up and the
+	 * interface should be skipped.
+	 */
+	if (CVMX_WAIT_FOR_FIELD64(CVMX_MIO_RST_CTLX(pcie_port), union cvmx_mio_rst_ctlx, rst_done, ==, 1, 10000)) {
+		pr_notice("PCIe: Port %d stuck in reset, skipping.\n", pcie_port);
+		return -1;
+	}
+
+	/* Check BIST status */
+	pemx_bist_status.u64 = cvmx_read_csr(CVMX_PEMX_BIST_STATUS(pcie_port));
+	if (pemx_bist_status.u64)
+		pr_notice("PCIe: BIST FAILED for port %d (0x%016llx)\n", pcie_port, CAST64(pemx_bist_status.u64));
+	pemx_bist_status2.u64 = cvmx_read_csr(CVMX_PEMX_BIST_STATUS2(pcie_port));
+	/* Errata PCIE-14766 may cause the lower 6 bits to be randomly set on CN63XXp1 */
+	if (OCTEON_IS_MODEL(OCTEON_CN63XX_PASS1_X))
+		pemx_bist_status2.u64 &= ~0x3full;
+	if (pemx_bist_status2.u64)
+		pr_notice("PCIe: BIST2 FAILED for port %d (0x%016llx)\n", pcie_port, CAST64(pemx_bist_status2.u64));
+
+	/* Initialize the config space CSRs */
+	__cvmx_pcie_rc_initialize_config_space(pcie_port);
+
+	/* Enable gen2 speed selection */
+	pciercx_cfg515.u32 = cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG515(pcie_port));
+	pciercx_cfg515.s.dsc = 1;
+	cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG515(pcie_port), pciercx_cfg515.u32);
+
+	/* Bring the link up */
+	if (__cvmx_pcie_rc_initialize_link_gen2(pcie_port)) {
+		/*
+		 * Some gen1 devices don't handle the gen 2 training
+		 * correctly. Disable gen2 and try again with only
+		 * gen1
+		 */
+		union cvmx_pciercx_cfg031 pciercx_cfg031;
+		pciercx_cfg031.u32 = cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG031(pcie_port));
+		pciercx_cfg031.s.mls = 1;
+		cvmx_pcie_cfgx_write(pcie_port, CVMX_PCIERCX_CFG031(pcie_port), pciercx_cfg031.u32);
+		if (__cvmx_pcie_rc_initialize_link_gen2(pcie_port)) {
+			pr_notice("PCIe: Link timeout on port %d, probably the slot is empty\n", pcie_port);
+			return -1;
+		}
+	}
+
+	/* Store merge control (SLI_MEM_ACCESS_CTL[TIMER,MAX_WORD]) */
+	sli_mem_access_ctl.u64 = cvmx_read_csr(CVMX_PEXP_SLI_MEM_ACCESS_CTL);
+	sli_mem_access_ctl.s.max_word = 0;	/* Allow 16 words to combine */
+	sli_mem_access_ctl.s.timer = 127;	/* Wait up to 127 cycles for more data */
+	cvmx_write_csr(CVMX_PEXP_SLI_MEM_ACCESS_CTL, sli_mem_access_ctl.u64);
+
+	/* Setup Mem access SubDIDs */
+	mem_access_subid.u64 = 0;
+	mem_access_subid.s.port = pcie_port; /* Port the request is sent to. */
+	mem_access_subid.s.nmerge = 0;	/* Allow merging as it works on CN6XXX. */
+	mem_access_subid.s.esr = 1;	/* Endian-swap for Reads. */
+	mem_access_subid.s.esw = 1;	/* Endian-swap for Writes. */
+	mem_access_subid.s.wtype = 0;	/* "No snoop" and "Relaxed ordering" are not set */
+	mem_access_subid.s.rtype = 0;	/* "No snoop" and "Relaxed ordering" are not set */
+	/* PCIe Address Bits <63:34>. */
+	if (OCTEON_IS_MODEL(OCTEON_CN68XX))
+		mem_access_subid.cn68xx.ba = 0;
+	else
+		mem_access_subid.s.ba = 0;
+
+	/*
+	 * Setup mem access 12-15 for port 0, 16-19 for port 1,
+	 * supplying 36 bits of address space.
+	 */
+	for (i = 12 + pcie_port * 4; i < 16 + pcie_port * 4; i++) {
+		cvmx_write_csr(CVMX_PEXP_SLI_MEM_ACCESS_SUBIDX(i), mem_access_subid.u64);
+		/* Set each SUBID to extend the addressable range */
+		__cvmx_increment_ba(&mem_access_subid);
+	}
+
+	/*
+	 * Disable the peer to peer forwarding register. This must be
+	 * setup by the OS after it enumerates the bus and assigns
+	 * addresses to the PCIe busses.
+	 */
+	for (i = 0; i < 4; i++) {
+		cvmx_write_csr(CVMX_PEMX_P2P_BARX_START(i, pcie_port), -1);
+		cvmx_write_csr(CVMX_PEMX_P2P_BARX_END(i, pcie_port), -1);
+	}
+
+	/* Set Octeon's BAR0 to decode 0-16KB. It overlaps with Bar2 */
+	cvmx_write_csr(CVMX_PEMX_P2N_BAR0_START(pcie_port), 0);
+
+	/*
+	 * Set Octeon's BAR2 to decode 0-2^41. Bar0 and Bar1 take
+	 * precedence where they overlap. It also overlaps with the
+	 * device addresses, so make sure the peer to peer forwarding
+	 * is set right.
+	 */
+	cvmx_write_csr(CVMX_PEMX_P2N_BAR2_START(pcie_port), 0);
+
+	/*
+	 * Setup BAR2 attributes
+	 * Relaxed Ordering (NPEI_CTL_PORTn[PTLP_RO,CTLP_RO, WAIT_COM])
+	 * - PTLP_RO,CTLP_RO should normally be set (except for debug).
+	 * - WAIT_COM=0 will likely work for all applications.
+	 * Load completion relaxed ordering (NPEI_CTL_PORTn[WAITL_COM])
+	 */
+	pemx_bar_ctl.u64 = cvmx_read_csr(CVMX_PEMX_BAR_CTL(pcie_port));
+	pemx_bar_ctl.s.bar1_siz = 3;  /* 256MB BAR1*/
+	pemx_bar_ctl.s.bar2_enb = 1;
+	pemx_bar_ctl.s.bar2_esx = 1;
+	pemx_bar_ctl.s.bar2_cax = 0;
+	cvmx_write_csr(CVMX_PEMX_BAR_CTL(pcie_port), pemx_bar_ctl.u64);
+	sli_ctl_portx.u64 = cvmx_read_csr(CVMX_PEXP_SLI_CTL_PORTX(pcie_port));
+	sli_ctl_portx.s.ptlp_ro = 1;
+	sli_ctl_portx.s.ctlp_ro = 1;
+	sli_ctl_portx.s.wait_com = 0;
+	sli_ctl_portx.s.waitl_com = 0;
+	cvmx_write_csr(CVMX_PEXP_SLI_CTL_PORTX(pcie_port), sli_ctl_portx.u64);
+
+	/* BAR1 follows BAR2 */
+	cvmx_write_csr(CVMX_PEMX_P2N_BAR1_START(pcie_port), CVMX_PCIE_BAR1_RC_BASE);
+
+	bar1_index.u64 = 0;
+	bar1_index.s.addr_idx = (CVMX_PCIE_BAR1_PHYS_BASE >> 22);
+	bar1_index.s.ca = 1;	   /* Not Cached */
+	bar1_index.s.end_swp = 1;  /* Endian Swap mode */
+	bar1_index.s.addr_v = 1;   /* Valid entry */
+
+	for (i = 0; i < 16; i++) {
+		cvmx_write_csr(CVMX_PEMX_BAR1_INDEXX(i, pcie_port), bar1_index.u64);
+		/* 256MB / 16 >> 22 == 4 */
+		bar1_index.s.addr_idx += (((1ull << 28) / 16ull) >> 22);
+	}
+
+	/*
+	 * Allow config retries for 250ms. Count is based off the 5Ghz
+	 * SERDES clock.
+	 */
+	pemx_ctl_status.u64 = cvmx_read_csr(CVMX_PEMX_CTL_STATUS(pcie_port));
+	pemx_ctl_status.s.cfg_rtry = 250 * 5000000 / 0x10000;
+	cvmx_write_csr(CVMX_PEMX_CTL_STATUS(pcie_port), pemx_ctl_status.u64);
+
+	/* Display the link status */
+	pciercx_cfg032.u32 = cvmx_pcie_cfgx_read(pcie_port, CVMX_PCIERCX_CFG032(pcie_port));
+	pr_notice("PCIe: Port %d link active, %d lanes, speed gen%d\n", pcie_port, pciercx_cfg032.s.nlw, pciercx_cfg032.s.ls);
+
+	return 0;
+}
+
+/**
+ * Initialize a PCIe port for use in host(RC) mode. It doesn't enumerate the bus.
+ *
+ * @pcie_port: PCIe port to initialize
+ *
+ * Returns Zero on success
+ */
+static int cvmx_pcie_rc_initialize(int pcie_port)
+{
+	int result;
+	if (octeon_has_feature(OCTEON_FEATURE_NPEI))
+		result = __cvmx_pcie_rc_initialize_gen1(pcie_port);
+	else
+		result = __cvmx_pcie_rc_initialize_gen2(pcie_port);
+	return result;
+}
+
+/* Above was cvmx-pcie.c, below original pcie.c */
+
+/**
+ * Map a PCI device to the appropriate interrupt line
+ *
+ * @dev:    The Linux PCI device structure for the device to map
+ * @slot:   The slot number for this device on __BUS 0__. Linux
+ *		 enumerates through all the bridges and figures out the
+ *		 slot on Bus 0 where this device eventually hooks to.
+ * @pin:    The PCI interrupt pin read from the device, then swizzled
+ *		 as it goes through each bridge.
+ * Returns Interrupt number for the device
+ */
+int octeon_pcie_pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	/*
+	 * The EBH5600 board with the PCI to PCIe bridge mistakenly
+	 * wires the first slot for both device id 2 and interrupt
+	 * A. According to the PCI spec, device id 2 should be C. The
+	 * following kludge attempts to fix this.
+	 */
+	if (strstr(octeon_board_type_string(), "EBH5600") &&
+	    dev->bus && dev->bus->parent) {
+		/*
+		 * Iterate all the way up the device chain and find
+		 * the root bus.
+		 */
+		while (dev->bus && dev->bus->parent)
+			dev = to_pci_dev(dev->bus->bridge);
+		/*
+		 * If the root bus is number 0 and the PEX 8114 is the
+		 * root, assume we are behind the miswired bus. We
+		 * need to correct the swizzle level by two. Yuck.
+		 */
+		if ((dev->bus->number == 1) &&
+		    (dev->vendor == 0x10b5) && (dev->device == 0x8114)) {
+			/*
+			 * The pin field is one based, not zero. We
+			 * need to swizzle it by minus two.
+			 */
+			pin = ((pin - 3) & 3) + 1;
+		}
+	}
+	/*
+	 * The -1 is because pin starts with one, not zero. It might
+	 * be that this equation needs to include the slot number, but
+	 * I don't have hardware to check that against.
+	 */
+	return pin - 1 + OCTEON_IRQ_PCI_INT0;
+}
+
+static	void set_cfg_read_retry(u32 retry_cnt)
+{
+	union cvmx_pemx_ctl_status pemx_ctl;
+	pemx_ctl.u64 = cvmx_read_csr(CVMX_PEMX_CTL_STATUS(1));
+	pemx_ctl.s.cfg_rtry = retry_cnt;
+	cvmx_write_csr(CVMX_PEMX_CTL_STATUS(1), pemx_ctl.u64);
+}
+
+
+static u32 disable_cfg_read_retry(void)
+{
+	u32 retry_cnt;
+
+	union cvmx_pemx_ctl_status pemx_ctl;
+	pemx_ctl.u64 = cvmx_read_csr(CVMX_PEMX_CTL_STATUS(1));
+	retry_cnt =  pemx_ctl.s.cfg_rtry;
+	pemx_ctl.s.cfg_rtry = 0;
+	cvmx_write_csr(CVMX_PEMX_CTL_STATUS(1), pemx_ctl.u64);
+	return retry_cnt;
+}
+
+static int is_cfg_retry(void)
+{
+	union cvmx_pemx_int_sum pemx_int_sum;
+	pemx_int_sum.u64 = cvmx_read_csr(CVMX_PEMX_INT_SUM(1));
+	if (pemx_int_sum.s.crs_dr)
+		return 1;
+	return 0;
+}
+
+/*
+ * Read a value from configuration space
+ *
+ */
+static int octeon_pcie_read_config(unsigned int pcie_port, struct pci_bus *bus,
+				   unsigned int devfn, int reg, int size,
+				   u32 *val)
+{
+	union octeon_cvmemctl cvmmemctl;
+	union octeon_cvmemctl cvmmemctl_save;
+	int bus_number = bus->number;
+	int cfg_retry = 0;
+	int retry_cnt = 0;
+	int max_retry_cnt = 10;
+	u32 cfg_retry_cnt = 0;
+
+	cvmmemctl_save.u64 = 0;
+	BUG_ON(pcie_port >= ARRAY_SIZE(enable_pcie_bus_num_war));
+	/*
+	 * For the top level bus make sure our hardware bus number
+	 * matches the software one
+	 */
+	if (bus->parent == NULL) {
+		if (enable_pcie_bus_num_war[pcie_port])
+			bus_number = 0;
+		else {
+			union cvmx_pciercx_cfg006 pciercx_cfg006;
+			pciercx_cfg006.u32 = cvmx_pcie_cfgx_read(pcie_port,
+					     CVMX_PCIERCX_CFG006(pcie_port));
+			if (pciercx_cfg006.s.pbnum != bus_number) {
+				pciercx_cfg006.s.pbnum = bus_number;
+				pciercx_cfg006.s.sbnum = bus_number;
+				pciercx_cfg006.s.subbnum = bus_number;
+				cvmx_pcie_cfgx_write(pcie_port,
+					    CVMX_PCIERCX_CFG006(pcie_port),
+					    pciercx_cfg006.u32);
+			}
+		}
+	}
+
+	/*
+	 * PCIe only has a single device connected to Octeon. It is
+	 * always device ID 0. Don't bother doing reads for other
+	 * device IDs on the first segment.
+	 */
+	if ((bus->parent == NULL) && (devfn >> 3 != 0))
+		return PCIBIOS_FUNC_NOT_SUPPORTED;
+
+	/*
+	 * The following is a workaround for the CN57XX, CN56XX,
+	 * CN55XX, and CN54XX errata with PCIe config reads from non
+	 * existent devices.  These chips will hang the PCIe link if a
+	 * config read is performed that causes a UR response.
+	 */
+	if (OCTEON_IS_MODEL(OCTEON_CN56XX_PASS1) ||
+	    OCTEON_IS_MODEL(OCTEON_CN56XX_PASS1_1)) {
+		/*
+		 * For our EBH5600 board, port 0 has a bridge with two
+		 * PCI-X slots. We need a new special checks to make
+		 * sure we only probe valid stuff.  The PCIe->PCI-X
+		 * bridge only respondes to device ID 0, function
+		 * 0-1
+		 */
+		if ((bus->parent == NULL) && (devfn >= 2))
+			return PCIBIOS_FUNC_NOT_SUPPORTED;
+		/*
+		 * The PCI-X slots are device ID 2,3. Choose one of
+		 * the below "if" blocks based on what is plugged into
+		 * the board.
+		 */
+#if 1
+		/* Use this option if you aren't using either slot */
+		if (bus_number == 2)
+			return PCIBIOS_FUNC_NOT_SUPPORTED;
+#elif 0
+		/*
+		 * Use this option if you are using the first slot but
+		 * not the second.
+		 */
+		if ((bus_number == 2) && (devfn >> 3 != 2))
+			return PCIBIOS_FUNC_NOT_SUPPORTED;
+#elif 0
+		/*
+		 * Use this option if you are using the second slot
+		 * but not the first.
+		 */
+		if ((bus_number == 2) && (devfn >> 3 != 3))
+			return PCIBIOS_FUNC_NOT_SUPPORTED;
+#elif 0
+		/* Use this opion if you are using both slots */
+		if ((bus_number == 2) &&
+		    !((devfn == (2 << 3)) || (devfn == (3 << 3))))
+			return PCIBIOS_FUNC_NOT_SUPPORTED;
+#endif
+
+		/* The following #if gives a more complicated example. This is
+		   the required checks for running a Nitrox CN16XX-NHBX in the
+		   slot of the EBH5600. This card has a PLX PCIe bridge with
+		   four Nitrox PLX parts behind it */
+#if 0
+		/* PLX bridge with 4 ports */
+		if ((bus_number == 4) &&
+		    !((devfn >> 3 >= 1) && (devfn >> 3 <= 4)))
+			return PCIBIOS_FUNC_NOT_SUPPORTED;
+		/* Nitrox behind PLX 1 */
+		if ((bus_number == 5) && (devfn >> 3 != 0))
+			return PCIBIOS_FUNC_NOT_SUPPORTED;
+		/* Nitrox behind PLX 2 */
+		if ((bus_number == 6) && (devfn >> 3 != 0))
+			return PCIBIOS_FUNC_NOT_SUPPORTED;
+		/* Nitrox behind PLX 3 */
+		if ((bus_number == 7) && (devfn >> 3 != 0))
+			return PCIBIOS_FUNC_NOT_SUPPORTED;
+		/* Nitrox behind PLX 4 */
+		if ((bus_number == 8) && (devfn >> 3 != 0))
+			return PCIBIOS_FUNC_NOT_SUPPORTED;
+#endif
+
+		/*
+		 * Shorten the DID timeout so bus errors for PCIe
+		 * config reads from non existent devices happen
+		 * faster. This allows us to continue booting even if
+		 * the above "if" checks are wrong.  Once one of these
+		 * errors happens, the PCIe port is dead.
+		 */
+		cvmmemctl_save.u64 = __read_64bit_c0_register($11, 7);
+		cvmmemctl.u64 = cvmmemctl_save.u64;
+		cvmmemctl.s.didtto = 2;
+		__write_64bit_c0_register($11, 7, cvmmemctl.u64);
+	}
+
+	if ((OCTEON_IS_MODEL(OCTEON_CN63XX)) && (enable_pcie_14459_war))
+		cfg_retry_cnt = disable_cfg_read_retry();
+
+	pr_debug("pcie_cfg_rd port=%d b=%d devfn=0x%03x reg=0x%03x"
+		 " size=%d ", pcie_port, bus_number, devfn, reg, size);
+	do {
+		switch (size) {
+		case 4:
+			*val = cvmx_pcie_config_read32(pcie_port, bus_number,
+				devfn >> 3, devfn & 0x7, reg);
+		break;
+		case 2:
+			*val = cvmx_pcie_config_read16(pcie_port, bus_number,
+				devfn >> 3, devfn & 0x7, reg);
+		break;
+		case 1:
+			*val = cvmx_pcie_config_read8(pcie_port, bus_number,
+				devfn >> 3, devfn & 0x7, reg);
+		break;
+		default:
+			if (OCTEON_IS_MODEL(OCTEON_CN63XX))
+				set_cfg_read_retry(cfg_retry_cnt);
+			return PCIBIOS_FUNC_NOT_SUPPORTED;
+		}
+		if ((OCTEON_IS_MODEL(OCTEON_CN63XX)) &&
+			(enable_pcie_14459_war)) {
+			cfg_retry = is_cfg_retry();
+			retry_cnt++;
+			if (retry_cnt > max_retry_cnt) {
+				pr_err(" pcie cfg_read retries failed. retry_cnt=%d\n",
+				       retry_cnt);
+				cfg_retry = 0;
+			}
+		}
+	} while (cfg_retry);
+
+	if ((OCTEON_IS_MODEL(OCTEON_CN63XX)) && (enable_pcie_14459_war))
+		set_cfg_read_retry(cfg_retry_cnt);
+	pr_debug("val=%08x  : tries=%02d\n", *val, retry_cnt);
+	if (OCTEON_IS_MODEL(OCTEON_CN56XX_PASS1) ||
+	    OCTEON_IS_MODEL(OCTEON_CN56XX_PASS1_1))
+		write_c0_cvmmemctl(cvmmemctl_save.u64);
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int octeon_pcie0_read_config(struct pci_bus *bus, unsigned int devfn,
+				    int reg, int size, u32 *val)
+{
+	return octeon_pcie_read_config(0, bus, devfn, reg, size, val);
+}
+
+static int octeon_pcie1_read_config(struct pci_bus *bus, unsigned int devfn,
+				    int reg, int size, u32 *val)
+{
+	return octeon_pcie_read_config(1, bus, devfn, reg, size, val);
+}
+
+static int octeon_dummy_read_config(struct pci_bus *bus, unsigned int devfn,
+				    int reg, int size, u32 *val)
+{
+	return PCIBIOS_FUNC_NOT_SUPPORTED;
+}
+
+/*
+ * Write a value to PCI configuration space
+ */
+static int octeon_pcie_write_config(unsigned int pcie_port, struct pci_bus *bus,
+				    unsigned int devfn, int reg,
+				    int size, u32 val)
+{
+	int bus_number = bus->number;
+
+	BUG_ON(pcie_port >= ARRAY_SIZE(enable_pcie_bus_num_war));
+
+	if ((bus->parent == NULL) && (enable_pcie_bus_num_war[pcie_port]))
+		bus_number = 0;
+
+	pr_debug("pcie_cfg_wr port=%d b=%d devfn=0x%03x"
+		 " reg=0x%03x size=%d val=%08x\n", pcie_port, bus_number, devfn,
+		 reg, size, val);
+
+
+	switch (size) {
+	case 4:
+		cvmx_pcie_config_write32(pcie_port, bus_number, devfn >> 3,
+					 devfn & 0x7, reg, val);
+		break;
+	case 2:
+		cvmx_pcie_config_write16(pcie_port, bus_number, devfn >> 3,
+					 devfn & 0x7, reg, val);
+		break;
+	case 1:
+		cvmx_pcie_config_write8(pcie_port, bus_number, devfn >> 3,
+					devfn & 0x7, reg, val);
+		break;
+	default:
+		return PCIBIOS_FUNC_NOT_SUPPORTED;
+	}
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int octeon_pcie0_write_config(struct pci_bus *bus, unsigned int devfn,
+				     int reg, int size, u32 val)
+{
+	return octeon_pcie_write_config(0, bus, devfn, reg, size, val);
+}
+
+static int octeon_pcie1_write_config(struct pci_bus *bus, unsigned int devfn,
+				     int reg, int size, u32 val)
+{
+	return octeon_pcie_write_config(1, bus, devfn, reg, size, val);
+}
+
+static int octeon_dummy_write_config(struct pci_bus *bus, unsigned int devfn,
+				     int reg, int size, u32 val)
+{
+	return PCIBIOS_FUNC_NOT_SUPPORTED;
+}
+
+static struct pci_ops octeon_pcie0_ops = {
+	.read	= octeon_pcie0_read_config,
+	.write	= octeon_pcie0_write_config,
+};
+
+static struct resource octeon_pcie0_mem_resource = {
+	.name = "Octeon PCIe0 MEM",
+	.flags = IORESOURCE_MEM,
+};
+
+static struct resource octeon_pcie0_io_resource = {
+	.name = "Octeon PCIe0 IO",
+	.flags = IORESOURCE_IO,
+};
+
+static struct pci_controller octeon_pcie0_controller = {
+	.pci_ops = &octeon_pcie0_ops,
+	.mem_resource = &octeon_pcie0_mem_resource,
+	.io_resource = &octeon_pcie0_io_resource,
+};
+
+static struct pci_ops octeon_pcie1_ops = {
+	.read	= octeon_pcie1_read_config,
+	.write	= octeon_pcie1_write_config,
+};
+
+static struct resource octeon_pcie1_mem_resource = {
+	.name = "Octeon PCIe1 MEM",
+	.flags = IORESOURCE_MEM,
+};
+
+static struct resource octeon_pcie1_io_resource = {
+	.name = "Octeon PCIe1 IO",
+	.flags = IORESOURCE_IO,
+};
+
+static struct pci_controller octeon_pcie1_controller = {
+	.pci_ops = &octeon_pcie1_ops,
+	.mem_resource = &octeon_pcie1_mem_resource,
+	.io_resource = &octeon_pcie1_io_resource,
+};
+
+static struct pci_ops octeon_dummy_ops = {
+	.read	= octeon_dummy_read_config,
+	.write	= octeon_dummy_write_config,
+};
+
+static struct resource octeon_dummy_mem_resource = {
+	.name = "Virtual PCIe MEM",
+	.flags = IORESOURCE_MEM,
+};
+
+static struct resource octeon_dummy_io_resource = {
+	.name = "Virtual PCIe IO",
+	.flags = IORESOURCE_IO,
+};
+
+static struct pci_controller octeon_dummy_controller = {
+	.pci_ops = &octeon_dummy_ops,
+	.mem_resource = &octeon_dummy_mem_resource,
+	.io_resource = &octeon_dummy_io_resource,
+};
+
+static int device_needs_bus_num_war(uint32_t deviceid)
+{
+#define IDT_VENDOR_ID 0x111d
+
+	if ((deviceid  & 0xffff) == IDT_VENDOR_ID)
+		return 1;
+	return 0;
+}
+
+/**
+ * Initialize the Octeon PCIe controllers
+ *
+ * Returns
+ */
+static int __init octeon_pcie_setup(void)
+{
+	int result;
+	int host_mode;
+	int srio_war15205 = 0, port;
+	union cvmx_sli_ctl_portx sli_ctl_portx;
+	union cvmx_sriox_status_reg sriox_status_reg;
+
+	/* These chips don't have PCIe */
+	if (!octeon_has_feature(OCTEON_FEATURE_PCIE))
+		return 0;
+
+	/* No PCIe simulation */
+	if (octeon_is_simulation())
+		return 0;
+
+	/* Disable PCI if instructed on the command line */
+	if (pcie_disable)
+		return 0;
+
+	/* Point pcibios_map_irq() to the PCIe version of it */
+	octeon_pcibios_map_irq = octeon_pcie_pcibios_map_irq;
+
+	/*
+	 * PCIe I/O range. It is based on port 0 but includes up until
+	 * port 1's end.
+	 */
+	set_io_port_base(CVMX_ADD_IO_SEG(cvmx_pcie_get_io_base_address(0)));
+	ioport_resource.start = 0;
+	ioport_resource.end =
+		cvmx_pcie_get_io_base_address(1) -
+		cvmx_pcie_get_io_base_address(0) + cvmx_pcie_get_io_size(1) - 1;
+
+	/*
+	 * Create a dummy PCIe controller to swallow up bus 0. IDT bridges
+	 * don't work if the primary bus number is zero. Here we add a fake
+	 * PCIe controller that the kernel will give bus 0. This allows
+	 * us to not change the normal kernel bus enumeration
+	 */
+	octeon_dummy_controller.io_map_base = -1;
+	octeon_dummy_controller.mem_resource->start = (1ull<<48);
+	octeon_dummy_controller.mem_resource->end = (1ull<<48);
+	register_pci_controller(&octeon_dummy_controller);
+
+	if (octeon_has_feature(OCTEON_FEATURE_NPEI)) {
+		union cvmx_npei_ctl_status npei_ctl_status;
+		npei_ctl_status.u64 = cvmx_read_csr(CVMX_PEXP_NPEI_CTL_STATUS);
+		host_mode = npei_ctl_status.s.host_mode;
+		octeon_dma_bar_type = OCTEON_DMA_BAR_TYPE_PCIE;
+	} else {
+		union cvmx_mio_rst_ctlx mio_rst_ctl;
+		mio_rst_ctl.u64 = cvmx_read_csr(CVMX_MIO_RST_CTLX(0));
+		host_mode = mio_rst_ctl.s.host_mode;
+		octeon_dma_bar_type = OCTEON_DMA_BAR_TYPE_PCIE2;
+	}
+
+	if (host_mode) {
+		pr_notice("PCIe: Initializing port 0\n");
+		/* CN63XX pass 1_x/2.0 errata PCIe-15205 */
+		if (OCTEON_IS_MODEL(OCTEON_CN63XX_PASS1_X) ||
+			OCTEON_IS_MODEL(OCTEON_CN63XX_PASS2_0)) {
+			sriox_status_reg.u64 = cvmx_read_csr(CVMX_SRIOX_STATUS_REG(0));
+			if (sriox_status_reg.s.srio) {
+				srio_war15205 += 1;	 /* Port is SRIO */
+				port = 0;
+			}
+		}
+		result = cvmx_pcie_rc_initialize(0);
+		if (result == 0) {
+			uint32_t device0;
+			/* Memory offsets are physical addresses */
+			octeon_pcie0_controller.mem_offset =
+				cvmx_pcie_get_mem_base_address(0);
+			/* IO offsets are Mips virtual addresses */
+			octeon_pcie0_controller.io_map_base =
+				CVMX_ADD_IO_SEG(cvmx_pcie_get_io_base_address
+						(0));
+			octeon_pcie0_controller.io_offset = 0;
+			/*
+			 * To keep things similar to PCI, we start
+			 * device addresses at the same place as PCI
+			 * uisng big bar support. This normally
+			 * translates to 4GB-256MB, which is the same
+			 * as most x86 PCs.
+			 */
+			octeon_pcie0_controller.mem_resource->start =
+				cvmx_pcie_get_mem_base_address(0) +
+				(4ul << 30) - (OCTEON_PCI_BAR1_HOLE_SIZE << 20);
+			octeon_pcie0_controller.mem_resource->end =
+				cvmx_pcie_get_mem_base_address(0) +
+				cvmx_pcie_get_mem_size(0) - 1;
+			/*
+			 * Ports must be above 16KB for the ISA bus
+			 * filtering in the PCI-X to PCI bridge.
+			 */
+			octeon_pcie0_controller.io_resource->start = 4 << 10;
+			octeon_pcie0_controller.io_resource->end =
+				cvmx_pcie_get_io_size(0) - 1;
+			msleep(100); /* Some devices need extra time */
+			register_pci_controller(&octeon_pcie0_controller);
+			device0 = cvmx_pcie_config_read32(0, 0, 0, 0, 0);
+			enable_pcie_bus_num_war[0] =
+				device_needs_bus_num_war(device0);
+		}
+	} else {
+		pr_notice("PCIe: Port 0 in endpoint mode, skipping.\n");
+		/* CN63XX pass 1_x/2.0 errata PCIe-15205 */
+		if (OCTEON_IS_MODEL(OCTEON_CN63XX_PASS1_X) ||
+			OCTEON_IS_MODEL(OCTEON_CN63XX_PASS2_0)) {
+			srio_war15205 += 1;
+			port = 0;
+		}
+	}
+
+	if (octeon_has_feature(OCTEON_FEATURE_NPEI)) {
+		host_mode = 1;
+		/* Skip the 2nd port on CN52XX if port 0 is in 4 lane mode */
+		if (OCTEON_IS_MODEL(OCTEON_CN52XX)) {
+			union cvmx_npei_dbg_data dbg_data;
+			dbg_data.u64 = cvmx_read_csr(CVMX_PEXP_NPEI_DBG_DATA);
+			if (dbg_data.cn52xx.qlm0_link_width)
+				host_mode = 0;
+		}
+	} else {
+		union cvmx_mio_rst_ctlx mio_rst_ctl;
+		mio_rst_ctl.u64 = cvmx_read_csr(CVMX_MIO_RST_CTLX(1));
+		host_mode = mio_rst_ctl.s.host_mode;
+	}
+
+	if (host_mode) {
+		pr_notice("PCIe: Initializing port 1\n");
+		/* CN63XX pass 1_x/2.0 errata PCIe-15205 */
+		if (OCTEON_IS_MODEL(OCTEON_CN63XX_PASS1_X) ||
+			OCTEON_IS_MODEL(OCTEON_CN63XX_PASS2_0)) {
+			sriox_status_reg.u64 = cvmx_read_csr(CVMX_SRIOX_STATUS_REG(1));
+			if (sriox_status_reg.s.srio) {
+				srio_war15205 += 1;	 /* Port is SRIO */
+				port = 1;
+			}
+		}
+		result = cvmx_pcie_rc_initialize(1);
+		if (result == 0) {
+			uint32_t device0;
+			/* Memory offsets are physical addresses */
+			octeon_pcie1_controller.mem_offset =
+				cvmx_pcie_get_mem_base_address(1);
+			/*
+			 * To calculate the address for accessing the 2nd PCIe device,
+			 * either 'io_map_base' (pci_iomap()), or 'mips_io_port_base'
+			 * (ioport_map()) value is added to
+			 * pci_resource_start(dev,bar)). The 'mips_io_port_base' is set
+			 * only once based on first PCIe. Also changing 'io_map_base'
+			 * based on first slot's value so that both the routines will
+			 * work properly.
+			 */
+			octeon_pcie1_controller.io_map_base =
+				CVMX_ADD_IO_SEG(cvmx_pcie_get_io_base_address(0));
+			/* IO offsets are Mips virtual addresses */
+			octeon_pcie1_controller.io_offset =
+				cvmx_pcie_get_io_base_address(1) -
+				cvmx_pcie_get_io_base_address(0);
+			/*
+			 * To keep things similar to PCI, we start device
+			 * addresses at the same place as PCI uisng big bar
+			 * support. This normally translates to 4GB-256MB,
+			 * which is the same as most x86 PCs.
+			 */
+			octeon_pcie1_controller.mem_resource->start =
+				cvmx_pcie_get_mem_base_address(1) + (4ul << 30) -
+				(OCTEON_PCI_BAR1_HOLE_SIZE << 20);
+			octeon_pcie1_controller.mem_resource->end =
+				cvmx_pcie_get_mem_base_address(1) +
+				cvmx_pcie_get_mem_size(1) - 1;
+			/*
+			 * Ports must be above 16KB for the ISA bus filtering
+			 * in the PCI-X to PCI bridge.
+			 */
+			octeon_pcie1_controller.io_resource->start =
+				cvmx_pcie_get_io_base_address(1) -
+				cvmx_pcie_get_io_base_address(0);
+			octeon_pcie1_controller.io_resource->end =
+				octeon_pcie1_controller.io_resource->start +
+				cvmx_pcie_get_io_size(1) - 1;
+			msleep(100); /* Some devices need extra time */
+			register_pci_controller(&octeon_pcie1_controller);
+			device0 = cvmx_pcie_config_read32(1, 0, 0, 0, 0);
+			enable_pcie_bus_num_war[1] =
+				device_needs_bus_num_war(device0);
+		}
+	} else {
+		pr_notice("PCIe: Port 1 not in root complex mode, skipping.\n");
+		/* CN63XX pass 1_x/2.0 errata PCIe-15205  */
+		if (OCTEON_IS_MODEL(OCTEON_CN63XX_PASS1_X) ||
+			OCTEON_IS_MODEL(OCTEON_CN63XX_PASS2_0)) {
+			srio_war15205 += 1;
+			port = 1;
+		}
+	}
+
+	/*
+	 * CN63XX pass 1_x/2.0 errata PCIe-15205 requires setting all
+	 * of SRIO MACs SLI_CTL_PORT*[INT*_MAP] to similar value and
+	 * all of PCIe Macs SLI_CTL_PORT*[INT*_MAP] to different value
+	 * from the previous set values
+	 */
+	if (OCTEON_IS_MODEL(OCTEON_CN63XX_PASS1_X) ||
+		OCTEON_IS_MODEL(OCTEON_CN63XX_PASS2_0)) {
+		if (srio_war15205 == 1) {
+			sli_ctl_portx.u64 = cvmx_read_csr(CVMX_PEXP_SLI_CTL_PORTX(port));
+			sli_ctl_portx.s.inta_map = 1;
+			sli_ctl_portx.s.intb_map = 1;
+			sli_ctl_portx.s.intc_map = 1;
+			sli_ctl_portx.s.intd_map = 1;
+			cvmx_write_csr(CVMX_PEXP_SLI_CTL_PORTX(port), sli_ctl_portx.u64);
+
+			sli_ctl_portx.u64 = cvmx_read_csr(CVMX_PEXP_SLI_CTL_PORTX(!port));
+			sli_ctl_portx.s.inta_map = 0;
+			sli_ctl_portx.s.intb_map = 0;
+			sli_ctl_portx.s.intc_map = 0;
+			sli_ctl_portx.s.intd_map = 0;
+			cvmx_write_csr(CVMX_PEXP_SLI_CTL_PORTX(!port), sli_ctl_portx.u64);
+		}
+	}
+
+	octeon_pci_dma_init();
+
+	return 0;
+}
+arch_initcall(octeon_pcie_setup);
diff --git a/arch/mips/pic32/Kconfig b/arch/mips/pic32/Kconfig
new file mode 100644
index 000000000..bb6ab1f3e
--- /dev/null
+++ b/arch/mips/pic32/Kconfig
@@ -0,0 +1,50 @@
+# SPDX-License-Identifier: GPL-2.0
+if MACH_PIC32
+
+choice
+	prompt "Machine Type"
+
+config PIC32MZDA
+	bool "Microchip PIC32MZDA Platform"
+	select BOOT_ELF32
+	select BOOT_RAW
+	select CEVT_R4K
+	select CSRC_R4K
+	select DMA_NONCOHERENT
+	select SYS_HAS_CPU_MIPS32_R2
+	select SYS_HAS_EARLY_PRINTK
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select GPIOLIB
+	select COMMON_CLK
+	select LIBFDT
+	select USE_OF
+	select PINCTRL
+	select PIC32_EVIC
+	help
+	  Support for the Microchip PIC32MZDA microcontroller.
+
+	  This is a 32-bit microcontroller with support for external or
+	  internally packaged DDR2 memory up to 128MB.
+
+	  For more information, see <http://www.microchip.com/>.
+
+endchoice
+
+choice
+	prompt "Devicetree selection"
+	default DTB_PIC32_NONE
+	help
+	  Select the devicetree.
+
+config DTB_PIC32_NONE
+	bool "None"
+
+config DTB_PIC32_MZDA_SK
+	bool "PIC32MZDA Starter Kit"
+	depends on PIC32MZDA
+	select BUILTIN_DTB
+
+endchoice
+
+endif # MACH_PIC32
diff --git a/arch/mips/pic32/Makefile b/arch/mips/pic32/Makefile
new file mode 100644
index 000000000..6183e4a46
--- /dev/null
+++ b/arch/mips/pic32/Makefile
@@ -0,0 +1,7 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Joshua Henderson, <joshua.henderson@microchip.com>
+# Copyright (C) 2015 Microchip Technology, Inc.  All rights reserved.
+#
+obj-$(CONFIG_MACH_PIC32) += common/
+obj-$(CONFIG_PIC32MZDA) += pic32mzda/
diff --git a/arch/mips/pic32/Platform b/arch/mips/pic32/Platform
new file mode 100644
index 000000000..1e92e52a1
--- /dev/null
+++ b/arch/mips/pic32/Platform
@@ -0,0 +1,6 @@
+#
+# PIC32MZDA
+#
+cflags-$(CONFIG_PIC32MZDA)	+= -I$(srctree)/arch/mips/include/asm/mach-pic32
+load-$(CONFIG_PIC32MZDA)	+= 0xffffffff88000000
+all-$(CONFIG_PIC32MZDA)		:= $(COMPRESSION_FNAME).bin
diff --git a/arch/mips/pic32/common/Makefile b/arch/mips/pic32/common/Makefile
new file mode 100644
index 000000000..a60750ab7
--- /dev/null
+++ b/arch/mips/pic32/common/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Joshua Henderson, <joshua.henderson@microchip.com>
+# Copyright (C) 2015 Microchip Technology, Inc.  All rights reserved.
+#
+obj-y = reset.o irq.o
diff --git a/arch/mips/pic32/common/irq.c b/arch/mips/pic32/common/irq.c
new file mode 100644
index 000000000..fb00b797b
--- /dev/null
+++ b/arch/mips/pic32/common/irq.c
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Joshua Henderson <joshua.henderson@microchip.com>
+ * Copyright (C) 2015 Microchip Technology Inc.  All rights reserved.
+ */
+#include <linux/init.h>
+#include <linux/irqchip.h>
+#include <asm/irq.h>
+
+void __init arch_init_irq(void)
+{
+	irqchip_init();
+}
diff --git a/arch/mips/pic32/common/reset.c b/arch/mips/pic32/common/reset.c
new file mode 100644
index 000000000..a5fd7a8e2
--- /dev/null
+++ b/arch/mips/pic32/common/reset.c
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Joshua Henderson <joshua.henderson@microchip.com>
+ * Copyright (C) 2015 Microchip Technology Inc.  All rights reserved.
+ */
+#include <linux/init.h>
+#include <linux/pm.h>
+#include <asm/reboot.h>
+#include <asm/mach-pic32/pic32.h>
+
+#define PIC32_RSWRST		0x10
+
+static void pic32_halt(void)
+{
+	while (1) {
+		__asm__(".set push;\n"
+			".set arch=r4000;\n"
+			"wait;\n"
+			".set pop;\n"
+		);
+	}
+}
+
+static void pic32_machine_restart(char *command)
+{
+	void __iomem *reg =
+		ioremap(PIC32_BASE_RESET + PIC32_RSWRST, sizeof(u32));
+
+	pic32_syskey_unlock();
+
+	/* magic write/read */
+	__raw_writel(1, reg);
+	(void)__raw_readl(reg);
+
+	pic32_halt();
+}
+
+static void pic32_machine_halt(void)
+{
+	local_irq_disable();
+
+	pic32_halt();
+}
+
+static int __init mips_reboot_setup(void)
+{
+	_machine_restart = pic32_machine_restart;
+	_machine_halt = pic32_machine_halt;
+	pm_power_off = pic32_machine_halt;
+
+	return 0;
+}
+
+arch_initcall(mips_reboot_setup);
diff --git a/arch/mips/pic32/pic32mzda/Makefile b/arch/mips/pic32/pic32mzda/Makefile
new file mode 100644
index 000000000..3b505142b
--- /dev/null
+++ b/arch/mips/pic32/pic32mzda/Makefile
@@ -0,0 +1,9 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Joshua Henderson, <joshua.henderson@microchip.com>
+# Copyright (C) 2015 Microchip Technology, Inc.  All rights reserved.
+#
+obj-y			:= config.o early_clk.o init.o time.o
+
+obj-$(CONFIG_EARLY_PRINTK)	+= early_console.o      \
+				   early_pin.o
diff --git a/arch/mips/pic32/pic32mzda/config.c b/arch/mips/pic32/pic32mzda/config.c
new file mode 100644
index 000000000..f69532007
--- /dev/null
+++ b/arch/mips/pic32/pic32mzda/config.c
@@ -0,0 +1,118 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Purna Chandra Mandal, purna.mandal@microchip.com
+ * Copyright (C) 2015 Microchip Technology Inc.  All rights reserved.
+ */
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/of_platform.h>
+
+#include <asm/mach-pic32/pic32.h>
+
+#include "pic32mzda.h"
+
+#define PIC32_CFGCON	0x0000
+#define PIC32_DEVID	0x0020
+#define PIC32_SYSKEY	0x0030
+#define PIC32_CFGEBIA	0x00c0
+#define PIC32_CFGEBIC	0x00d0
+#define PIC32_CFGCON2	0x00f0
+#define PIC32_RCON	0x1240
+
+static void __iomem *pic32_conf_base;
+static DEFINE_SPINLOCK(config_lock);
+static u32 pic32_reset_status;
+
+static u32 pic32_conf_get_reg_field(u32 offset, u32 rshift, u32 mask)
+{
+	u32 v;
+
+	v = readl(pic32_conf_base + offset);
+	v >>= rshift;
+	v &= mask;
+
+	return v;
+}
+
+static u32 pic32_conf_modify_atomic(u32 offset, u32 mask, u32 set)
+{
+	u32 v;
+	unsigned long flags;
+
+	spin_lock_irqsave(&config_lock, flags);
+	v = readl(pic32_conf_base + offset);
+	v &= ~mask;
+	v |= (set & mask);
+	writel(v, pic32_conf_base + offset);
+	spin_unlock_irqrestore(&config_lock, flags);
+
+	return 0;
+}
+
+int pic32_enable_lcd(void)
+{
+	return pic32_conf_modify_atomic(PIC32_CFGCON2, BIT(31), BIT(31));
+}
+
+int pic32_disable_lcd(void)
+{
+	return pic32_conf_modify_atomic(PIC32_CFGCON2, BIT(31), 0);
+}
+
+int pic32_set_lcd_mode(int mode)
+{
+	u32 mask = mode ? BIT(30) : 0;
+
+	return pic32_conf_modify_atomic(PIC32_CFGCON2, BIT(30), mask);
+}
+
+int pic32_set_sdhci_adma_fifo_threshold(u32 rthrsh, u32 wthrsh)
+{
+	u32 clr, set;
+
+	clr = (0x3ff << 4) | (0x3ff << 16);
+	set = (rthrsh << 4) | (wthrsh << 16);
+	return pic32_conf_modify_atomic(PIC32_CFGCON2, clr, set);
+}
+
+void pic32_syskey_unlock_debug(const char *func, const ulong line)
+{
+	void __iomem *syskey = pic32_conf_base + PIC32_SYSKEY;
+
+	pr_debug("%s: called from %s:%lu\n", __func__, func, line);
+	writel(0x00000000, syskey);
+	writel(0xAA996655, syskey);
+	writel(0x556699AA, syskey);
+}
+
+static u32 pic32_get_device_id(void)
+{
+	return pic32_conf_get_reg_field(PIC32_DEVID, 0, 0x0fffffff);
+}
+
+static u32 pic32_get_device_version(void)
+{
+	return pic32_conf_get_reg_field(PIC32_DEVID, 28, 0xf);
+}
+
+u32 pic32_get_boot_status(void)
+{
+	return pic32_reset_status;
+}
+EXPORT_SYMBOL(pic32_get_boot_status);
+
+void __init pic32_config_init(void)
+{
+	pic32_conf_base = ioremap(PIC32_BASE_CONFIG, 0x110);
+	if (!pic32_conf_base)
+		panic("pic32: config base not mapped");
+
+	/* Boot Status */
+	pic32_reset_status = readl(pic32_conf_base + PIC32_RCON);
+	writel(-1, PIC32_CLR(pic32_conf_base + PIC32_RCON));
+
+	/* Device Information */
+	pr_info("Device Id: 0x%08x, Device Ver: 0x%04x\n",
+		pic32_get_device_id(),
+		pic32_get_device_version());
+}
diff --git a/arch/mips/pic32/pic32mzda/early_clk.c b/arch/mips/pic32/pic32mzda/early_clk.c
new file mode 100644
index 000000000..6001e507d
--- /dev/null
+++ b/arch/mips/pic32/pic32mzda/early_clk.c
@@ -0,0 +1,98 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Joshua Henderson <joshua.henderson@microchip.com>
+ * Copyright (C) 2015 Microchip Technology Inc.  All rights reserved.
+ */
+#include <asm/mach-pic32/pic32.h>
+
+#include "pic32mzda.h"
+
+/* Oscillators, PLL & clocks */
+#define ICLK_MASK	0x00000080
+#define PLLDIV_MASK	0x00000007
+#define CUROSC_MASK	0x00000007
+#define PLLMUL_MASK	0x0000007F
+#define PB_MASK		0x00000007
+#define FRC1		0
+#define FRC2		7
+#define SPLL		1
+#define POSC		2
+#define FRC_CLK		8000000
+
+#define PIC32_POSC_FREQ	24000000
+
+#define OSCCON		0x0000
+#define SPLLCON		0x0020
+#define PB1DIV		0x0140
+
+u32 pic32_get_sysclk(void)
+{
+	u32 osc_freq = 0;
+	u32 pllclk;
+	u32 frcdivn;
+	u32 osccon;
+	u32 spllcon;
+	int curr_osc;
+
+	u32 plliclk;
+	u32 pllidiv;
+	u32 pllodiv;
+	u32 pllmult;
+	u32 frcdiv;
+
+	void __iomem *osc_base = ioremap(PIC32_BASE_OSC, 0x200);
+
+	osccon = __raw_readl(osc_base + OSCCON);
+	spllcon = __raw_readl(osc_base + SPLLCON);
+
+	plliclk = (spllcon & ICLK_MASK);
+	pllidiv = ((spllcon >> 8) & PLLDIV_MASK) + 1;
+	pllodiv = ((spllcon >> 24) & PLLDIV_MASK);
+	pllmult = ((spllcon >> 16) & PLLMUL_MASK) + 1;
+	frcdiv = ((osccon >> 24) & PLLDIV_MASK);
+
+	pllclk = plliclk ? FRC_CLK : PIC32_POSC_FREQ;
+	frcdivn = ((1 << frcdiv) + 1) + (128 * (frcdiv == 7));
+
+	if (pllodiv < 2)
+		pllodiv = 2;
+	else if (pllodiv < 5)
+		pllodiv = (1 << pllodiv);
+	else
+		pllodiv = 32;
+
+	curr_osc = (int)((osccon >> 12) & CUROSC_MASK);
+
+	switch (curr_osc) {
+	case FRC1:
+	case FRC2:
+		osc_freq = FRC_CLK / frcdivn;
+		break;
+	case SPLL:
+		osc_freq = ((pllclk / pllidiv) * pllmult) / pllodiv;
+		break;
+	case POSC:
+		osc_freq = PIC32_POSC_FREQ;
+		break;
+	default:
+		break;
+	}
+
+	iounmap(osc_base);
+
+	return osc_freq;
+}
+
+u32 pic32_get_pbclk(int bus)
+{
+	u32 clk_freq;
+	void __iomem *osc_base = ioremap(PIC32_BASE_OSC, 0x200);
+	u32 pbxdiv = PB1DIV + ((bus - 1) * 0x10);
+	u32 pbdiv = (__raw_readl(osc_base + pbxdiv) & PB_MASK) + 1;
+
+	iounmap(osc_base);
+
+	clk_freq = pic32_get_sysclk();
+
+	return clk_freq / pbdiv;
+}
diff --git a/arch/mips/pic32/pic32mzda/early_console.c b/arch/mips/pic32/pic32mzda/early_console.c
new file mode 100644
index 000000000..3cd1b408f
--- /dev/null
+++ b/arch/mips/pic32/pic32mzda/early_console.c
@@ -0,0 +1,161 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Joshua Henderson <joshua.henderson@microchip.com>
+ * Copyright (C) 2015 Microchip Technology Inc.  All rights reserved.
+ */
+#include <asm/mach-pic32/pic32.h>
+#include <asm/fw/fw.h>
+#include <asm/setup.h>
+
+#include "pic32mzda.h"
+#include "early_pin.h"
+
+/* Default early console parameters */
+#define EARLY_CONSOLE_PORT	1
+#define EARLY_CONSOLE_BAUDRATE	115200
+
+#define UART_ENABLE		BIT(15)
+#define UART_ENABLE_RX		BIT(12)
+#define UART_ENABLE_TX		BIT(10)
+#define UART_TX_FULL		BIT(9)
+
+/* UART1(x == 0) - UART6(x == 5) */
+#define UART_BASE(x)	((x) * 0x0200)
+#define U_MODE(x)	UART_BASE(x)
+#define U_STA(x)	(UART_BASE(x) + 0x10)
+#define U_TXR(x)	(UART_BASE(x) + 0x20)
+#define U_BRG(x)	(UART_BASE(x) + 0x40)
+
+static void __iomem *uart_base;
+static int console_port = -1;
+
+static int __init configure_uart_pins(int port)
+{
+	switch (port) {
+	case 1:
+		pic32_pps_input(IN_FUNC_U2RX, IN_RPB0);
+		pic32_pps_output(OUT_FUNC_U2TX, OUT_RPG9);
+		break;
+	case 5:
+		pic32_pps_input(IN_FUNC_U6RX, IN_RPD0);
+		pic32_pps_output(OUT_FUNC_U6TX, OUT_RPB8);
+		break;
+	default:
+		return -1;
+	}
+
+	return 0;
+}
+
+static void __init configure_uart(int port, int baud)
+{
+	u32 pbclk;
+
+	pbclk = pic32_get_pbclk(2);
+
+	__raw_writel(0, uart_base + U_MODE(port));
+	__raw_writel(((pbclk / baud) / 16) - 1, uart_base + U_BRG(port));
+	__raw_writel(UART_ENABLE, uart_base + U_MODE(port));
+	__raw_writel(UART_ENABLE_TX | UART_ENABLE_RX,
+		     uart_base + PIC32_SET(U_STA(port)));
+}
+
+static void __init setup_early_console(int port, int baud)
+{
+	if (configure_uart_pins(port))
+		return;
+
+	console_port = port;
+	configure_uart(console_port, baud);
+}
+
+static char * __init pic32_getcmdline(void)
+{
+	/*
+	 * arch_mem_init() has not been called yet, so we don't have a real
+	 * command line setup if using CONFIG_CMDLINE_BOOL.
+	 */
+#ifdef CONFIG_CMDLINE_OVERRIDE
+	return CONFIG_CMDLINE;
+#else
+	return fw_getcmdline();
+#endif
+}
+
+static int __init get_port_from_cmdline(char *arch_cmdline)
+{
+	char *s;
+	int port = -1;
+
+	if (!arch_cmdline || *arch_cmdline == '\0')
+		goto _out;
+
+	s = strstr(arch_cmdline, "earlyprintk=");
+	if (s) {
+		s = strstr(s, "ttyS");
+		if (s)
+			s += 4;
+		else
+			goto _out;
+
+		port = (*s) - '0';
+	}
+
+_out:
+	return port;
+}
+
+static int __init get_baud_from_cmdline(char *arch_cmdline)
+{
+	char *s;
+	int baud = -1;
+
+	if (!arch_cmdline || *arch_cmdline == '\0')
+		goto _out;
+
+	s = strstr(arch_cmdline, "earlyprintk=");
+	if (s) {
+		s = strstr(s, "ttyS");
+		if (s)
+			s += 6;
+		else
+			goto _out;
+
+		baud = 0;
+		while (*s >= '0' && *s <= '9')
+			baud = baud * 10 + *s++ - '0';
+	}
+
+_out:
+	return baud;
+}
+
+void __init fw_init_early_console(void)
+{
+	char *arch_cmdline = pic32_getcmdline();
+	int baud, port;
+
+	uart_base = ioremap(PIC32_BASE_UART, 0xc00);
+
+	baud = get_baud_from_cmdline(arch_cmdline);
+	port = get_port_from_cmdline(arch_cmdline);
+
+	if (port == -1)
+		port = EARLY_CONSOLE_PORT;
+
+	if (baud == -1)
+		baud = EARLY_CONSOLE_BAUDRATE;
+
+	setup_early_console(port, baud);
+}
+
+void prom_putchar(char c)
+{
+	if (console_port >= 0) {
+		while (__raw_readl(
+				uart_base + U_STA(console_port)) & UART_TX_FULL)
+			;
+
+		__raw_writel(c, uart_base + U_TXR(console_port));
+	}
+}
diff --git a/arch/mips/pic32/pic32mzda/early_pin.c b/arch/mips/pic32/pic32mzda/early_pin.c
new file mode 100644
index 000000000..f2822632b
--- /dev/null
+++ b/arch/mips/pic32/pic32mzda/early_pin.c
@@ -0,0 +1,267 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Joshua Henderson <joshua.henderson@microchip.com>
+ * Copyright (C) 2015 Microchip Technology Inc.  All rights reserved.
+ */
+#include <asm/io.h>
+
+#include "early_pin.h"
+
+#define PPS_BASE 0x1f800000
+
+/* Input PPS Registers */
+#define INT1R 0x1404
+#define INT2R 0x1408
+#define INT3R 0x140C
+#define INT4R 0x1410
+#define T2CKR 0x1418
+#define T3CKR 0x141C
+#define T4CKR 0x1420
+#define T5CKR 0x1424
+#define T6CKR 0x1428
+#define T7CKR 0x142C
+#define T8CKR 0x1430
+#define T9CKR 0x1434
+#define IC1R 0x1438
+#define IC2R 0x143C
+#define IC3R 0x1440
+#define IC4R 0x1444
+#define IC5R 0x1448
+#define IC6R 0x144C
+#define IC7R 0x1450
+#define IC8R 0x1454
+#define IC9R 0x1458
+#define OCFAR 0x1460
+#define U1RXR 0x1468
+#define U1CTSR 0x146C
+#define U2RXR 0x1470
+#define U2CTSR 0x1474
+#define U3RXR 0x1478
+#define U3CTSR 0x147C
+#define U4RXR 0x1480
+#define U4CTSR 0x1484
+#define U5RXR 0x1488
+#define U5CTSR 0x148C
+#define U6RXR 0x1490
+#define U6CTSR 0x1494
+#define SDI1R 0x149C
+#define SS1R 0x14A0
+#define SDI2R 0x14A8
+#define SS2R 0x14AC
+#define SDI3R 0x14B4
+#define SS3R 0x14B8
+#define SDI4R 0x14C0
+#define SS4R 0x14C4
+#define SDI5R 0x14CC
+#define SS5R 0x14D0
+#define SDI6R 0x14D8
+#define SS6R 0x14DC
+#define C1RXR 0x14E0
+#define C2RXR 0x14E4
+#define REFCLKI1R 0x14E8
+#define REFCLKI3R 0x14F0
+#define REFCLKI4R 0x14F4
+
+static const struct
+{
+	int function;
+	int reg;
+} input_pin_reg[] = {
+	{ IN_FUNC_INT3, INT3R },
+	{ IN_FUNC_T2CK, T2CKR },
+	{ IN_FUNC_T6CK, T6CKR },
+	{ IN_FUNC_IC3, IC3R  },
+	{ IN_FUNC_IC7, IC7R },
+	{ IN_FUNC_U1RX, U1RXR },
+	{ IN_FUNC_U2CTS, U2CTSR },
+	{ IN_FUNC_U5RX, U5RXR },
+	{ IN_FUNC_U6CTS, U6CTSR },
+	{ IN_FUNC_SDI1, SDI1R },
+	{ IN_FUNC_SDI3, SDI3R },
+	{ IN_FUNC_SDI5, SDI5R },
+	{ IN_FUNC_SS6, SS6R },
+	{ IN_FUNC_REFCLKI1, REFCLKI1R },
+	{ IN_FUNC_INT4, INT4R },
+	{ IN_FUNC_T5CK, T5CKR },
+	{ IN_FUNC_T7CK, T7CKR },
+	{ IN_FUNC_IC4, IC4R },
+	{ IN_FUNC_IC8, IC8R },
+	{ IN_FUNC_U3RX, U3RXR },
+	{ IN_FUNC_U4CTS, U4CTSR },
+	{ IN_FUNC_SDI2, SDI2R },
+	{ IN_FUNC_SDI4, SDI4R },
+	{ IN_FUNC_C1RX, C1RXR },
+	{ IN_FUNC_REFCLKI4, REFCLKI4R },
+	{ IN_FUNC_INT2, INT2R },
+	{ IN_FUNC_T3CK, T3CKR },
+	{ IN_FUNC_T8CK, T8CKR },
+	{ IN_FUNC_IC2, IC2R },
+	{ IN_FUNC_IC5, IC5R },
+	{ IN_FUNC_IC9, IC9R },
+	{ IN_FUNC_U1CTS, U1CTSR },
+	{ IN_FUNC_U2RX, U2RXR },
+	{ IN_FUNC_U5CTS, U5CTSR },
+	{ IN_FUNC_SS1, SS1R },
+	{ IN_FUNC_SS3, SS3R },
+	{ IN_FUNC_SS4, SS4R },
+	{ IN_FUNC_SS5, SS5R },
+	{ IN_FUNC_C2RX, C2RXR },
+	{ IN_FUNC_INT1, INT1R },
+	{ IN_FUNC_T4CK, T4CKR },
+	{ IN_FUNC_T9CK, T9CKR },
+	{ IN_FUNC_IC1, IC1R },
+	{ IN_FUNC_IC6, IC6R },
+	{ IN_FUNC_U3CTS, U3CTSR },
+	{ IN_FUNC_U4RX, U4RXR },
+	{ IN_FUNC_U6RX, U6RXR },
+	{ IN_FUNC_SS2, SS2R },
+	{ IN_FUNC_SDI6, SDI6R },
+	{ IN_FUNC_OCFA, OCFAR },
+	{ IN_FUNC_REFCLKI3, REFCLKI3R },
+};
+
+void pic32_pps_input(int function, int pin)
+{
+	void __iomem *pps_base = ioremap(PPS_BASE, 0xF4);
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(input_pin_reg); i++) {
+		if (input_pin_reg[i].function == function) {
+			__raw_writel(pin, pps_base + input_pin_reg[i].reg);
+			return;
+		}
+	}
+
+	iounmap(pps_base);
+}
+
+/* Output PPS Registers */
+#define RPA14R 0x1538
+#define RPA15R 0x153C
+#define RPB0R 0x1540
+#define RPB1R 0x1544
+#define RPB2R 0x1548
+#define RPB3R 0x154C
+#define RPB5R 0x1554
+#define RPB6R 0x1558
+#define RPB7R 0x155C
+#define RPB8R 0x1560
+#define RPB9R 0x1564
+#define RPB10R 0x1568
+#define RPB14R 0x1578
+#define RPB15R 0x157C
+#define RPC1R 0x1584
+#define RPC2R 0x1588
+#define RPC3R 0x158C
+#define RPC4R 0x1590
+#define RPC13R 0x15B4
+#define RPC14R 0x15B8
+#define RPD0R 0x15C0
+#define RPD1R 0x15C4
+#define RPD2R 0x15C8
+#define RPD3R 0x15CC
+#define RPD4R 0x15D0
+#define RPD5R 0x15D4
+#define RPD6R 0x15D8
+#define RPD7R 0x15DC
+#define RPD9R 0x15E4
+#define RPD10R 0x15E8
+#define RPD11R 0x15EC
+#define RPD12R 0x15F0
+#define RPD14R 0x15F8
+#define RPD15R 0x15FC
+#define RPE3R 0x160C
+#define RPE5R 0x1614
+#define RPE8R 0x1620
+#define RPE9R 0x1624
+#define RPF0R 0x1640
+#define RPF1R 0x1644
+#define RPF2R 0x1648
+#define RPF3R 0x164C
+#define RPF4R 0x1650
+#define RPF5R 0x1654
+#define RPF8R 0x1660
+#define RPF12R 0x1670
+#define RPF13R 0x1674
+#define RPG0R 0x1680
+#define RPG1R 0x1684
+#define RPG6R 0x1698
+#define RPG7R 0x169C
+#define RPG8R 0x16A0
+#define RPG9R 0x16A4
+
+static const struct
+{
+	int pin;
+	int reg;
+} output_pin_reg[] = {
+	{ OUT_RPD2, RPD2R },
+	{ OUT_RPG8, RPG8R },
+	{ OUT_RPF4, RPF4R },
+	{ OUT_RPD10, RPD10R },
+	{ OUT_RPF1, RPF1R },
+	{ OUT_RPB9, RPB9R },
+	{ OUT_RPB10, RPB10R },
+	{ OUT_RPC14, RPC14R },
+	{ OUT_RPB5, RPB5R },
+	{ OUT_RPC1, RPC1R },
+	{ OUT_RPD14, RPD14R },
+	{ OUT_RPG1, RPG1R },
+	{ OUT_RPA14, RPA14R },
+	{ OUT_RPD6, RPD6R },
+	{ OUT_RPD3, RPD3R },
+	{ OUT_RPG7, RPG7R },
+	{ OUT_RPF5, RPF5R },
+	{ OUT_RPD11, RPD11R },
+	{ OUT_RPF0, RPF0R },
+	{ OUT_RPB1, RPB1R },
+	{ OUT_RPE5, RPE5R },
+	{ OUT_RPC13, RPC13R },
+	{ OUT_RPB3, RPB3R },
+	{ OUT_RPC4, RPC4R },
+	{ OUT_RPD15, RPD15R },
+	{ OUT_RPG0, RPG0R },
+	{ OUT_RPA15, RPA15R },
+	{ OUT_RPD7, RPD7R },
+	{ OUT_RPD9, RPD9R },
+	{ OUT_RPG6, RPG6R },
+	{ OUT_RPB8, RPB8R },
+	{ OUT_RPB15, RPB15R },
+	{ OUT_RPD4, RPD4R },
+	{ OUT_RPB0, RPB0R },
+	{ OUT_RPE3, RPE3R },
+	{ OUT_RPB7, RPB7R },
+	{ OUT_RPF12, RPF12R },
+	{ OUT_RPD12, RPD12R },
+	{ OUT_RPF8, RPF8R },
+	{ OUT_RPC3, RPC3R },
+	{ OUT_RPE9, RPE9R },
+	{ OUT_RPD1, RPD1R },
+	{ OUT_RPG9, RPG9R },
+	{ OUT_RPB14, RPB14R },
+	{ OUT_RPD0, RPD0R },
+	{ OUT_RPB6, RPB6R },
+	{ OUT_RPD5, RPD5R },
+	{ OUT_RPB2, RPB2R },
+	{ OUT_RPF3, RPF3R },
+	{ OUT_RPF13, RPF13R },
+	{ OUT_RPC2, RPC2R },
+	{ OUT_RPE8, RPE8R },
+	{ OUT_RPF2, RPF2R },
+};
+
+void pic32_pps_output(int function, int pin)
+{
+	void __iomem *pps_base = ioremap(PPS_BASE, 0x170);
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(output_pin_reg); i++) {
+		if (output_pin_reg[i].pin == pin) {
+			__raw_writel(function,
+				pps_base + output_pin_reg[i].reg);
+			return;
+		}
+	}
+
+	iounmap(pps_base);
+}
diff --git a/arch/mips/pic32/pic32mzda/early_pin.h b/arch/mips/pic32/pic32mzda/early_pin.h
new file mode 100644
index 000000000..60e9c3210
--- /dev/null
+++ b/arch/mips/pic32/pic32mzda/early_pin.h
@@ -0,0 +1,233 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Joshua Henderson <joshua.henderson@microchip.com>
+ * Copyright (C) 2015 Microchip Technology Inc.  All rights reserved.
+ */
+#ifndef _PIC32MZDA_EARLY_PIN_H
+#define _PIC32MZDA_EARLY_PIN_H
+
+/*
+ * This is a complete, yet overly simplistic and unoptimized, PIC32MZDA PPS
+ * configuration only useful before we have full pinctrl initialized.
+ */
+
+/* Input PPS Functions */
+enum {
+	IN_FUNC_INT3,
+	IN_FUNC_T2CK,
+	IN_FUNC_T6CK,
+	IN_FUNC_IC3,
+	IN_FUNC_IC7,
+	IN_FUNC_U1RX,
+	IN_FUNC_U2CTS,
+	IN_FUNC_U5RX,
+	IN_FUNC_U6CTS,
+	IN_FUNC_SDI1,
+	IN_FUNC_SDI3,
+	IN_FUNC_SDI5,
+	IN_FUNC_SS6,
+	IN_FUNC_REFCLKI1,
+	IN_FUNC_INT4,
+	IN_FUNC_T5CK,
+	IN_FUNC_T7CK,
+	IN_FUNC_IC4,
+	IN_FUNC_IC8,
+	IN_FUNC_U3RX,
+	IN_FUNC_U4CTS,
+	IN_FUNC_SDI2,
+	IN_FUNC_SDI4,
+	IN_FUNC_C1RX,
+	IN_FUNC_REFCLKI4,
+	IN_FUNC_INT2,
+	IN_FUNC_T3CK,
+	IN_FUNC_T8CK,
+	IN_FUNC_IC2,
+	IN_FUNC_IC5,
+	IN_FUNC_IC9,
+	IN_FUNC_U1CTS,
+	IN_FUNC_U2RX,
+	IN_FUNC_U5CTS,
+	IN_FUNC_SS1,
+	IN_FUNC_SS3,
+	IN_FUNC_SS4,
+	IN_FUNC_SS5,
+	IN_FUNC_C2RX,
+	IN_FUNC_INT1,
+	IN_FUNC_T4CK,
+	IN_FUNC_T9CK,
+	IN_FUNC_IC1,
+	IN_FUNC_IC6,
+	IN_FUNC_U3CTS,
+	IN_FUNC_U4RX,
+	IN_FUNC_U6RX,
+	IN_FUNC_SS2,
+	IN_FUNC_SDI6,
+	IN_FUNC_OCFA,
+	IN_FUNC_REFCLKI3,
+};
+
+/* Input PPS Pins */
+#define IN_RPD2 0x00
+#define IN_RPG8 0x01
+#define IN_RPF4 0x02
+#define IN_RPD10 0x03
+#define IN_RPF1 0x04
+#define IN_RPB9 0x05
+#define IN_RPB10 0x06
+#define IN_RPC14 0x07
+#define IN_RPB5 0x08
+#define IN_RPC1 0x0A
+#define IN_RPD14 0x0B
+#define IN_RPG1 0x0C
+#define IN_RPA14 0x0D
+#define IN_RPD6 0x0E
+#define IN_RPD3 0x00
+#define IN_RPG7 0x01
+#define IN_RPF5 0x02
+#define IN_RPD11 0x03
+#define IN_RPF0 0x04
+#define IN_RPB1 0x05
+#define IN_RPE5 0x06
+#define IN_RPC13 0x07
+#define IN_RPB3 0x08
+#define IN_RPC4 0x0A
+#define IN_RPD15 0x0B
+#define IN_RPG0 0x0C
+#define IN_RPA15 0x0D
+#define IN_RPD7 0x0E
+#define IN_RPD9 0x00
+#define IN_RPG6 0x01
+#define IN_RPB8 0x02
+#define IN_RPB15 0x03
+#define IN_RPD4 0x04
+#define IN_RPB0 0x05
+#define IN_RPE3 0x06
+#define IN_RPB7 0x07
+#define IN_RPF12 0x09
+#define IN_RPD12 0x0A
+#define IN_RPF8 0x0B
+#define IN_RPC3 0x0C
+#define IN_RPE9 0x0D
+#define IN_RPD1 0x00
+#define IN_RPG9 0x01
+#define IN_RPB14 0x02
+#define IN_RPD0 0x03
+#define IN_RPB6 0x05
+#define IN_RPD5 0x06
+#define IN_RPB2 0x07
+#define IN_RPF3 0x08
+#define IN_RPF13 0x09
+#define IN_RPF2 0x0B
+#define IN_RPC2 0x0C
+#define IN_RPE8 0x0D
+
+/* Output PPS Pins */
+enum {
+	OUT_RPD2,
+	OUT_RPG8,
+	OUT_RPF4,
+	OUT_RPD10,
+	OUT_RPF1,
+	OUT_RPB9,
+	OUT_RPB10,
+	OUT_RPC14,
+	OUT_RPB5,
+	OUT_RPC1,
+	OUT_RPD14,
+	OUT_RPG1,
+	OUT_RPA14,
+	OUT_RPD6,
+	OUT_RPD3,
+	OUT_RPG7,
+	OUT_RPF5,
+	OUT_RPD11,
+	OUT_RPF0,
+	OUT_RPB1,
+	OUT_RPE5,
+	OUT_RPC13,
+	OUT_RPB3,
+	OUT_RPC4,
+	OUT_RPD15,
+	OUT_RPG0,
+	OUT_RPA15,
+	OUT_RPD7,
+	OUT_RPD9,
+	OUT_RPG6,
+	OUT_RPB8,
+	OUT_RPB15,
+	OUT_RPD4,
+	OUT_RPB0,
+	OUT_RPE3,
+	OUT_RPB7,
+	OUT_RPF12,
+	OUT_RPD12,
+	OUT_RPF8,
+	OUT_RPC3,
+	OUT_RPE9,
+	OUT_RPD1,
+	OUT_RPG9,
+	OUT_RPB14,
+	OUT_RPD0,
+	OUT_RPB6,
+	OUT_RPD5,
+	OUT_RPB2,
+	OUT_RPF3,
+	OUT_RPF13,
+	OUT_RPC2,
+	OUT_RPE8,
+	OUT_RPF2,
+};
+
+/* Output PPS Functions */
+#define OUT_FUNC_U3TX 0x01
+#define OUT_FUNC_U4RTS 0x02
+#define OUT_FUNC_SDO1 0x05
+#define OUT_FUNC_SDO2 0x06
+#define OUT_FUNC_SDO3 0x07
+#define OUT_FUNC_SDO5 0x09
+#define OUT_FUNC_SS6 0x0A
+#define OUT_FUNC_OC3 0x0B
+#define OUT_FUNC_OC6 0x0C
+#define OUT_FUNC_REFCLKO4 0x0D
+#define OUT_FUNC_C2OUT 0x0E
+#define OUT_FUNC_C1TX 0x0F
+#define OUT_FUNC_U1TX 0x01
+#define OUT_FUNC_U2RTS 0x02
+#define OUT_FUNC_U5TX 0x03
+#define OUT_FUNC_U6RTS 0x04
+#define OUT_FUNC_SDO1 0x05
+#define OUT_FUNC_SDO2 0x06
+#define OUT_FUNC_SDO3 0x07
+#define OUT_FUNC_SDO4 0x08
+#define OUT_FUNC_SDO5 0x09
+#define OUT_FUNC_OC4 0x0B
+#define OUT_FUNC_OC7 0x0C
+#define OUT_FUNC_REFCLKO1 0x0F
+#define OUT_FUNC_U3RTS 0x01
+#define OUT_FUNC_U4TX 0x02
+#define OUT_FUNC_U6TX 0x04
+#define OUT_FUNC_SS1 0x05
+#define OUT_FUNC_SS3 0x07
+#define OUT_FUNC_SS4 0x08
+#define OUT_FUNC_SS5 0x09
+#define OUT_FUNC_SDO6 0x0A
+#define OUT_FUNC_OC5 0x0B
+#define OUT_FUNC_OC8 0x0C
+#define OUT_FUNC_C1OUT 0x0E
+#define OUT_FUNC_REFCLKO3 0x0F
+#define OUT_FUNC_U1RTS 0x01
+#define OUT_FUNC_U2TX 0x02
+#define OUT_FUNC_U5RTS 0x03
+#define OUT_FUNC_U6TX 0x04
+#define OUT_FUNC_SS2 0x06
+#define OUT_FUNC_SDO4 0x08
+#define OUT_FUNC_SDO6 0x0A
+#define OUT_FUNC_OC2 0x0B
+#define OUT_FUNC_OC1 0x0C
+#define OUT_FUNC_OC9 0x0D
+#define OUT_FUNC_C2TX 0x0F
+
+void pic32_pps_input(int function, int pin);
+void pic32_pps_output(int function, int pin);
+
+#endif
diff --git a/arch/mips/pic32/pic32mzda/init.c b/arch/mips/pic32/pic32mzda/init.c
new file mode 100644
index 000000000..53b227a90
--- /dev/null
+++ b/arch/mips/pic32/pic32mzda/init.c
@@ -0,0 +1,127 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Joshua Henderson, joshua.henderson@microchip.com
+ * Copyright (C) 2015 Microchip Technology Inc.  All rights reserved.
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/of_address.h>
+#include <linux/of_fdt.h>
+#include <linux/of_platform.h>
+#include <linux/platform_data/sdhci-pic32.h>
+
+#include <asm/fw/fw.h>
+#include <asm/mips-boards/generic.h>
+#include <asm/prom.h>
+
+#include "pic32mzda.h"
+
+const char *get_system_type(void)
+{
+	return "PIC32MZDA";
+}
+
+void __init plat_mem_setup(void)
+{
+	void *dtb;
+
+	dtb = get_fdt();
+	if (!dtb) {
+		pr_err("pic32: no DTB found.\n");
+		return;
+	}
+
+	/*
+	 * Load the builtin device tree. This causes the chosen node to be
+	 * parsed resulting in our memory appearing.
+	 */
+	__dt_setup_arch(dtb);
+
+	pr_info("Found following command lines\n");
+	pr_info(" boot_command_line: %s\n", boot_command_line);
+	pr_info(" arcs_cmdline     : %s\n", arcs_cmdline);
+#ifdef CONFIG_CMDLINE_BOOL
+	pr_info(" builtin_cmdline  : %s\n", CONFIG_CMDLINE);
+#endif
+	if (dtb != __dtb_start)
+		strscpy(arcs_cmdline, boot_command_line, COMMAND_LINE_SIZE);
+
+#ifdef CONFIG_EARLY_PRINTK
+	fw_init_early_console();
+#endif
+	pic32_config_init();
+}
+
+static __init void pic32_init_cmdline(int argc, char *argv[])
+{
+	unsigned int count = COMMAND_LINE_SIZE - 1;
+	int i;
+	char *dst = &(arcs_cmdline[0]);
+	char *src;
+
+	for (i = 1; i < argc && count; ++i) {
+		src = argv[i];
+		while (*src && count) {
+			*dst++ = *src++;
+			--count;
+		}
+		*dst++ = ' ';
+	}
+	if (i > 1)
+		--dst;
+
+	*dst = 0;
+}
+
+void __init prom_init(void)
+{
+	pic32_init_cmdline((int)fw_arg0, (char **)fw_arg1);
+}
+
+static struct pic32_sdhci_platform_data sdhci_data = {
+	.setup_dma = pic32_set_sdhci_adma_fifo_threshold,
+};
+
+static struct of_dev_auxdata pic32_auxdata_lookup[] __initdata = {
+	OF_DEV_AUXDATA("microchip,pic32mzda-sdhci", 0, "sdhci", &sdhci_data),
+	{ /* sentinel */}
+};
+
+static int __init pic32_of_prepare_platform_data(struct of_dev_auxdata *lookup)
+{
+	struct device_node *root, *np;
+	struct resource res;
+
+	root = of_find_node_by_path("/");
+
+	for (; lookup->compatible; lookup++) {
+		np = of_find_compatible_node(NULL, NULL, lookup->compatible);
+		if (np) {
+			lookup->name = (char *)np->name;
+			if (lookup->phys_addr) {
+				of_node_put(np);
+				continue;
+			}
+			if (!of_address_to_resource(np, 0, &res))
+				lookup->phys_addr = res.start;
+			of_node_put(np);
+		}
+	}
+
+	of_node_put(root);
+
+	return 0;
+}
+
+static int __init plat_of_setup(void)
+{
+	if (!of_have_populated_dt())
+		panic("Device tree not present");
+
+	pic32_of_prepare_platform_data(pic32_auxdata_lookup);
+	if (of_platform_default_populate(NULL, pic32_auxdata_lookup, NULL))
+		panic("Failed to populate DT");
+
+	return 0;
+}
+arch_initcall(plat_of_setup);
diff --git a/arch/mips/pic32/pic32mzda/pic32mzda.h b/arch/mips/pic32/pic32mzda/pic32mzda.h
new file mode 100644
index 000000000..b7a93d8fe
--- /dev/null
+++ b/arch/mips/pic32/pic32mzda/pic32mzda.h
@@ -0,0 +1,21 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Joshua Henderson <joshua.henderson@microchip.com>
+ * Copyright (C) 2015 Microchip Technology Inc.  All rights reserved.
+ */
+#ifndef PIC32MZDA_COMMON_H
+#define PIC32MZDA_COMMON_H
+
+/* early clock */
+u32 pic32_get_pbclk(int bus);
+u32 pic32_get_sysclk(void);
+
+/* Device configuration */
+void __init pic32_config_init(void);
+int pic32_set_lcd_mode(int mode);
+int pic32_set_sdhci_adma_fifo_threshold(u32 rthrs, u32 wthrs);
+u32 pic32_get_boot_status(void);
+int pic32_disable_lcd(void);
+int pic32_enable_lcd(void);
+
+#endif
diff --git a/arch/mips/pic32/pic32mzda/time.c b/arch/mips/pic32/pic32mzda/time.c
new file mode 100644
index 000000000..777b515c5
--- /dev/null
+++ b/arch/mips/pic32/pic32mzda/time.c
@@ -0,0 +1,63 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Joshua Henderson <joshua.henderson@microchip.com>
+ * Copyright (C) 2015 Microchip Technology Inc.  All rights reserved.
+ */
+#include <linux/clocksource.h>
+#include <linux/init.h>
+#include <linux/irqdomain.h>
+#include <linux/of.h>
+#include <linux/of_clk.h>
+#include <linux/of_irq.h>
+
+#include <asm/time.h>
+
+#include "pic32mzda.h"
+
+static const struct of_device_id pic32_infra_match[] = {
+	{ .compatible = "microchip,pic32mzda-infra", },
+	{ },
+};
+
+#define DEFAULT_CORE_TIMER_INTERRUPT 0
+
+static unsigned int pic32_xlate_core_timer_irq(void)
+{
+	struct device_node *node;
+	unsigned int irq;
+
+	node = of_find_matching_node(NULL, pic32_infra_match);
+
+	if (WARN_ON(!node))
+		goto default_map;
+
+	irq = irq_of_parse_and_map(node, 0);
+
+	of_node_put(node);
+
+	if (!irq)
+		goto default_map;
+
+	return irq;
+
+default_map:
+
+	return irq_create_mapping(NULL, DEFAULT_CORE_TIMER_INTERRUPT);
+}
+
+unsigned int get_c0_compare_int(void)
+{
+	return pic32_xlate_core_timer_irq();
+}
+
+void __init plat_time_init(void)
+{
+	unsigned long rate = pic32_get_pbclk(7);
+
+	of_clk_init(NULL);
+
+	pr_info("CPU Clock: %ldMHz\n", rate / 1000000);
+	mips_hpt_frequency = rate / 2;
+
+	timer_probe();
+}
diff --git a/arch/mips/power/Makefile b/arch/mips/power/Makefile
new file mode 100644
index 000000000..14b7d9ee6
--- /dev/null
+++ b/arch/mips/power/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0-only
+obj-$(CONFIG_HIBERNATION) += cpu.o hibernate.o hibernate_asm.o
diff --git a/arch/mips/power/cpu.c b/arch/mips/power/cpu.c
new file mode 100644
index 000000000..a15e29dfc
--- /dev/null
+++ b/arch/mips/power/cpu.c
@@ -0,0 +1,42 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Suspend support specific for mips.
+ *
+ * Copyright (C) 2009 Lemote Inc.
+ * Author: Hu Hongbing <huhb@lemote.com>
+ *	   Wu Zhangjin <wuzhangjin@gmail.com>
+ */
+#include <asm/sections.h>
+#include <asm/fpu.h>
+#include <asm/dsp.h>
+
+static u32 saved_status;
+struct pt_regs saved_regs;
+
+void save_processor_state(void)
+{
+	saved_status = read_c0_status();
+
+	if (is_fpu_owner())
+		save_fp(current);
+
+	save_dsp(current);
+}
+
+void restore_processor_state(void)
+{
+	write_c0_status(saved_status);
+
+	if (is_fpu_owner())
+		restore_fp(current);
+
+	restore_dsp(current);
+}
+
+int pfn_is_nosave(unsigned long pfn)
+{
+	unsigned long nosave_begin_pfn = PFN_DOWN(__pa(&__nosave_begin));
+	unsigned long nosave_end_pfn = PFN_UP(__pa(&__nosave_end));
+
+	return	(pfn >= nosave_begin_pfn) && (pfn < nosave_end_pfn);
+}
diff --git a/arch/mips/power/hibernate.c b/arch/mips/power/hibernate.c
new file mode 100644
index 000000000..94ab17c3c
--- /dev/null
+++ b/arch/mips/power/hibernate.c
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <asm/tlbflush.h>
+
+extern int restore_image(void);
+
+int swsusp_arch_resume(void)
+{
+	/* Avoid TLB mismatch during and after kernel resume */
+	local_flush_tlb_all();
+	return restore_image();
+}
diff --git a/arch/mips/power/hibernate_asm.S b/arch/mips/power/hibernate_asm.S
new file mode 100644
index 000000000..e62538734
--- /dev/null
+++ b/arch/mips/power/hibernate_asm.S
@@ -0,0 +1,60 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Hibernation support specific for mips - temporary page tables
+ *
+ * Copyright (C) 2009 Lemote Inc.
+ * Author: Hu Hongbing <huhb@lemote.com>
+ *	   Wu Zhangjin <wuzhangjin@gmail.com>
+ */
+#include <asm/asm-offsets.h>
+#include <asm/regdef.h>
+#include <asm/asm.h>
+
+.text
+LEAF(swsusp_arch_suspend)
+	PTR_LA t0, saved_regs
+	PTR_S ra, PT_R31(t0)
+	PTR_S sp, PT_R29(t0)
+	PTR_S fp, PT_R30(t0)
+	PTR_S gp, PT_R28(t0)
+	PTR_S s0, PT_R16(t0)
+	PTR_S s1, PT_R17(t0)
+	PTR_S s2, PT_R18(t0)
+	PTR_S s3, PT_R19(t0)
+	PTR_S s4, PT_R20(t0)
+	PTR_S s5, PT_R21(t0)
+	PTR_S s6, PT_R22(t0)
+	PTR_S s7, PT_R23(t0)
+	j swsusp_save
+END(swsusp_arch_suspend)
+
+LEAF(restore_image)
+	PTR_L t0, restore_pblist
+0:
+	PTR_L t1, PBE_ADDRESS(t0)   /* source */
+	PTR_L t2, PBE_ORIG_ADDRESS(t0) /* destination */
+	PTR_ADDU t3, t1, _PAGE_SIZE
+1:
+	REG_L t8, (t1)
+	REG_S t8, (t2)
+	PTR_ADDIU t1, t1, SZREG
+	PTR_ADDIU t2, t2, SZREG
+	bne t1, t3, 1b
+	PTR_L t0, PBE_NEXT(t0)
+	bnez t0, 0b
+	PTR_LA t0, saved_regs
+	PTR_L ra, PT_R31(t0)
+	PTR_L sp, PT_R29(t0)
+	PTR_L fp, PT_R30(t0)
+	PTR_L gp, PT_R28(t0)
+	PTR_L s0, PT_R16(t0)
+	PTR_L s1, PT_R17(t0)
+	PTR_L s2, PT_R18(t0)
+	PTR_L s3, PT_R19(t0)
+	PTR_L s4, PT_R20(t0)
+	PTR_L s5, PT_R21(t0)
+	PTR_L s6, PT_R22(t0)
+	PTR_L s7, PT_R23(t0)
+	PTR_LI v0, 0x0
+	jr ra
+END(restore_image)
diff --git a/arch/mips/ralink/Kconfig b/arch/mips/ralink/Kconfig
new file mode 100644
index 000000000..f9fe15630
--- /dev/null
+++ b/arch/mips/ralink/Kconfig
@@ -0,0 +1,105 @@
+# SPDX-License-Identifier: GPL-2.0
+if RALINK
+
+config CLKEVT_RT3352
+	bool
+	depends on SOC_RT305X || SOC_MT7620
+	default y
+	select TIMER_OF
+	select CLKSRC_MMIO
+
+config RALINK_ILL_ACC
+	bool
+	depends on SOC_RT305X
+	default y
+
+config IRQ_INTC
+	bool
+	default y
+	depends on !SOC_MT7621
+
+choice
+	prompt "Ralink SoC selection"
+	default SOC_RT305X
+	help
+	  Select Ralink MIPS SoC type.
+
+	config SOC_RT288X
+		bool "RT288x"
+		select MIPS_AUTO_PFN_OFFSET
+		select MIPS_L1_CACHE_SHIFT_4
+		select HAVE_PCI
+
+	config SOC_RT305X
+		bool "RT305x"
+
+	config SOC_RT3883
+		bool "RT3883"
+		select HAVE_PCI
+
+	config SOC_MT7620
+		bool "MT7620/8"
+		select CPU_MIPSR2_IRQ_VI
+		select HAVE_PCI
+
+	config SOC_MT7621
+		bool "MT7621"
+		select MIPS_CPU_SCACHE
+		select SYS_SUPPORTS_MULTITHREADING
+		select SYS_SUPPORTS_SMP
+		select SYS_SUPPORTS_MIPS_CPS
+		select SYS_SUPPORTS_HIGHMEM
+		select MIPS_GIC
+		select CLKSRC_MIPS_GIC
+		select HAVE_PCI
+		select PCI_DRIVERS_GENERIC
+		select SOC_BUS
+
+		help
+		  The MT7621 system-on-a-chip includes an 880 MHz MIPS1004Kc dual-core CPU,
+		  a 5-port 10/100/1000 switch/PHY and one RGMII.
+endchoice
+
+choice
+	prompt "Devicetree selection"
+	depends on !SOC_MT7621
+	default DTB_RT_NONE
+	help
+	  Select the devicetree.
+
+	config DTB_RT_NONE
+		bool "None"
+
+	config DTB_RT2880_EVAL
+		bool "RT2880 eval kit"
+		depends on SOC_RT288X
+		select BUILTIN_DTB
+
+	config DTB_RT305X_EVAL
+		bool "RT305x eval kit"
+		depends on SOC_RT305X
+		select BUILTIN_DTB
+
+	config DTB_RT3883_EVAL
+		bool "RT3883 eval kit"
+		depends on SOC_RT3883
+		select BUILTIN_DTB
+
+	config DTB_MT7620A_EVAL
+		bool "MT7620A eval kit"
+		depends on SOC_MT7620
+		select BUILTIN_DTB
+
+	config DTB_OMEGA2P
+		bool "Onion Omega2+"
+		depends on SOC_MT7620
+		select BUILTIN_DTB
+
+	config DTB_VOCORE2
+		bool "VoCore2"
+		depends on SOC_MT7620
+		select BUILTIN_DTB
+
+endchoice
+
+endif
diff --git a/arch/mips/ralink/Makefile b/arch/mips/ralink/Makefile
new file mode 100644
index 000000000..26fabbdea
--- /dev/null
+++ b/arch/mips/ralink/Makefile
@@ -0,0 +1,28 @@
+# SPDX-License-Identifier: GPL-2.0-only
+# Makefile for the Ralink common stuff
+#
+# Copyright (C) 2009-2011 Gabor Juhos <juhosg@openwrt.org>
+# Copyright (C) 2013 John Crispin <john@phrozen.org>
+
+obj-y := prom.o of.o reset.o
+
+ifndef CONFIG_MIPS_GIC
+	obj-y += clk.o timer.o
+endif
+
+obj-$(CONFIG_CLKEVT_RT3352) += cevt-rt3352.o
+
+obj-$(CONFIG_RALINK_ILL_ACC) += ill_acc.o
+
+obj-$(CONFIG_IRQ_INTC) += irq.o
+obj-$(CONFIG_MIPS_GIC) += irq-gic.o timer-gic.o
+
+obj-$(CONFIG_SOC_RT288X) += rt288x.o
+obj-$(CONFIG_SOC_RT305X) += rt305x.o
+obj-$(CONFIG_SOC_RT3883) += rt3883.o
+obj-$(CONFIG_SOC_MT7620) += mt7620.o
+obj-$(CONFIG_SOC_MT7621) += mt7621.o
+
+obj-$(CONFIG_EARLY_PRINTK) += early_printk.o
+
+obj-$(CONFIG_DEBUG_FS) += bootrom.o
diff --git a/arch/mips/ralink/Platform b/arch/mips/ralink/Platform
new file mode 100644
index 000000000..02ee07914
--- /dev/null
+++ b/arch/mips/ralink/Platform
@@ -0,0 +1,33 @@
+#
+# Ralink SoC common stuff
+#
+cflags-$(CONFIG_RALINK)		+= -I$(srctree)/arch/mips/include/asm/mach-ralink
+
+#
+# Ralink RT288x
+#
+load-$(CONFIG_SOC_RT288X)	+= 0xffffffff88000000
+cflags-$(CONFIG_SOC_RT288X)	+= -I$(srctree)/arch/mips/include/asm/mach-ralink/rt288x
+
+#
+# Ralink RT305x
+#
+load-$(CONFIG_SOC_RT305X)	+= 0xffffffff80000000
+cflags-$(CONFIG_SOC_RT305X)	+= -I$(srctree)/arch/mips/include/asm/mach-ralink/rt305x
+
+#
+# Ralink RT3883
+#
+load-$(CONFIG_SOC_RT3883)	+= 0xffffffff80000000
+cflags-$(CONFIG_SOC_RT3883)	+= -I$(srctree)/arch/mips/include/asm/mach-ralink/rt3883
+
+#
+# Ralink MT7620
+#
+load-$(CONFIG_SOC_MT7620)	+= 0xffffffff80000000
+cflags-$(CONFIG_SOC_MT7620)	+= -I$(srctree)/arch/mips/include/asm/mach-ralink/mt7620
+
+# Ralink MT7621
+#
+load-$(CONFIG_SOC_MT7621)	+= 0xffffffff80001000
+cflags-$(CONFIG_SOC_MT7621)	+= -I$(srctree)/arch/mips/include/asm/mach-ralink/mt7621
diff --git a/arch/mips/ralink/bootrom.c b/arch/mips/ralink/bootrom.c
new file mode 100644
index 000000000..8c8cc0a81
--- /dev/null
+++ b/arch/mips/ralink/bootrom.c
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ * Copyright (C) 2013 John Crispin <john@phrozen.org>
+ */
+
+#include <linux/debugfs.h>
+#include <linux/seq_file.h>
+
+#define BOOTROM_OFFSET	0x10118000
+#define BOOTROM_SIZE	0x8000
+
+static void __iomem *membase = (void __iomem *) KSEG1ADDR(BOOTROM_OFFSET);
+
+static int bootrom_show(struct seq_file *s, void *unused)
+{
+	seq_write(s, membase, BOOTROM_SIZE);
+
+	return 0;
+}
+DEFINE_SHOW_ATTRIBUTE(bootrom);
+
+static int __init bootrom_setup(void)
+{
+	debugfs_create_file("bootrom", 0444, NULL, NULL, &bootrom_fops);
+	return 0;
+}
+
+postcore_initcall(bootrom_setup);
diff --git a/arch/mips/ralink/cevt-rt3352.c b/arch/mips/ralink/cevt-rt3352.c
new file mode 100644
index 000000000..269d4877d
--- /dev/null
+++ b/arch/mips/ralink/cevt-rt3352.c
@@ -0,0 +1,153 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2013 by John Crispin <john@phrozen.org>
+ */
+
+#include <linux/clockchips.h>
+#include <linux/clocksource.h>
+#include <linux/interrupt.h>
+#include <linux/reset.h>
+#include <linux/init.h>
+#include <linux/time.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_address.h>
+
+#include <asm/mach-ralink/ralink_regs.h>
+
+#define SYSTICK_FREQ		(50 * 1000)
+
+#define SYSTICK_CONFIG		0x00
+#define SYSTICK_COMPARE		0x04
+#define SYSTICK_COUNT		0x08
+
+/* route systick irq to mips irq 7 instead of the r4k-timer */
+#define CFG_EXT_STK_EN		0x2
+/* enable the counter */
+#define CFG_CNT_EN		0x1
+
+struct systick_device {
+	void __iomem *membase;
+	struct clock_event_device dev;
+	int irq_requested;
+	int freq_scale;
+};
+
+static int systick_set_oneshot(struct clock_event_device *evt);
+static int systick_shutdown(struct clock_event_device *evt);
+
+static int systick_next_event(unsigned long delta,
+				struct clock_event_device *evt)
+{
+	struct systick_device *sdev;
+	u32 count;
+
+	sdev = container_of(evt, struct systick_device, dev);
+	count = ioread32(sdev->membase + SYSTICK_COUNT);
+	count = (count + delta) % SYSTICK_FREQ;
+	iowrite32(count, sdev->membase + SYSTICK_COMPARE);
+
+	return 0;
+}
+
+static void systick_event_handler(struct clock_event_device *dev)
+{
+	/* noting to do here */
+}
+
+static irqreturn_t systick_interrupt(int irq, void *dev_id)
+{
+	struct clock_event_device *dev = (struct clock_event_device *) dev_id;
+
+	dev->event_handler(dev);
+
+	return IRQ_HANDLED;
+}
+
+static struct systick_device systick = {
+	.dev = {
+		/*
+		 * cevt-r4k uses 300, make sure systick
+		 * gets used if available
+		 */
+		.rating			= 310,
+		.features		= CLOCK_EVT_FEAT_ONESHOT,
+		.set_next_event		= systick_next_event,
+		.set_state_shutdown	= systick_shutdown,
+		.set_state_oneshot	= systick_set_oneshot,
+		.event_handler		= systick_event_handler,
+	},
+};
+
+static int systick_shutdown(struct clock_event_device *evt)
+{
+	struct systick_device *sdev;
+
+	sdev = container_of(evt, struct systick_device, dev);
+
+	if (sdev->irq_requested)
+		free_irq(systick.dev.irq, &systick.dev);
+	sdev->irq_requested = 0;
+	iowrite32(0, systick.membase + SYSTICK_CONFIG);
+
+	return 0;
+}
+
+static int systick_set_oneshot(struct clock_event_device *evt)
+{
+	const char *name = systick.dev.name;
+	struct systick_device *sdev;
+	int irq = systick.dev.irq;
+
+	sdev = container_of(evt, struct systick_device, dev);
+
+	if (!sdev->irq_requested) {
+		if (request_irq(irq, systick_interrupt,
+				IRQF_PERCPU | IRQF_TIMER, name, &systick.dev))
+			pr_err("Failed to request irq %d (%s)\n", irq, name);
+	}
+	sdev->irq_requested = 1;
+	iowrite32(CFG_EXT_STK_EN | CFG_CNT_EN,
+		  systick.membase + SYSTICK_CONFIG);
+
+	return 0;
+}
+
+static int __init ralink_systick_init(struct device_node *np)
+{
+	int ret;
+
+	systick.membase = of_iomap(np, 0);
+	if (!systick.membase)
+		return -ENXIO;
+
+	systick.dev.name = np->name;
+	clockevents_calc_mult_shift(&systick.dev, SYSTICK_FREQ, 60);
+	systick.dev.max_delta_ns = clockevent_delta2ns(0x7fff, &systick.dev);
+	systick.dev.max_delta_ticks = 0x7fff;
+	systick.dev.min_delta_ns = clockevent_delta2ns(0x3, &systick.dev);
+	systick.dev.min_delta_ticks = 0x3;
+	systick.dev.irq = irq_of_parse_and_map(np, 0);
+	if (!systick.dev.irq) {
+		pr_err("%pOFn: request_irq failed", np);
+		return -EINVAL;
+	}
+
+	ret = clocksource_mmio_init(systick.membase + SYSTICK_COUNT, np->name,
+				    SYSTICK_FREQ, 301, 16,
+				    clocksource_mmio_readl_up);
+	if (ret)
+		return ret;
+
+	clockevents_register_device(&systick.dev);
+
+	pr_info("%pOFn: running - mult: %d, shift: %d\n",
+			np, systick.dev.mult, systick.dev.shift);
+
+	return 0;
+}
+
+TIMER_OF_DECLARE(systick, "ralink,cevt-systick", ralink_systick_init);
diff --git a/arch/mips/ralink/clk.c b/arch/mips/ralink/clk.c
new file mode 100644
index 000000000..5b02bb7e0
--- /dev/null
+++ b/arch/mips/ralink/clk.c
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ *  Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
+ *  Copyright (C) 2013 John Crispin <john@phrozen.org>
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/export.h>
+#include <linux/clkdev.h>
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+
+#include <asm/time.h>
+
+#include "common.h"
+
+void ralink_clk_add(const char *dev, unsigned long rate)
+{
+	struct clk *clk = clk_register_fixed_rate(NULL, dev, NULL, 0, rate);
+
+	if (!clk)
+		panic("failed to add clock");
+
+	clkdev_create(clk, NULL, "%s", dev);
+}
+
+void __init plat_time_init(void)
+{
+	struct clk *clk;
+
+	ralink_of_remap();
+
+	ralink_clk_init();
+	clk = clk_get_sys("cpu", NULL);
+	if (IS_ERR(clk))
+		panic("unable to get CPU clock, err=%ld", PTR_ERR(clk));
+	pr_info("CPU Clock: %ldMHz\n", clk_get_rate(clk) / 1000000);
+	mips_hpt_frequency = clk_get_rate(clk) / 2;
+	clk_put(clk);
+	timer_probe();
+}
diff --git a/arch/mips/ralink/common.h b/arch/mips/ralink/common.h
new file mode 100644
index 000000000..87fc16751
--- /dev/null
+++ b/arch/mips/ralink/common.h
@@ -0,0 +1,35 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ *
+ * Copyright (C) 2013 John Crispin <john@phrozen.org>
+ */
+
+#ifndef _RALINK_COMMON_H__
+#define _RALINK_COMMON_H__
+
+#define RAMIPS_SYS_TYPE_LEN	32
+
+struct ralink_soc_info {
+	unsigned char sys_type[RAMIPS_SYS_TYPE_LEN];
+	unsigned char *compatible;
+
+	unsigned long mem_base;
+	unsigned long mem_size;
+	unsigned long mem_size_min;
+	unsigned long mem_size_max;
+	void (*mem_detect)(void);
+};
+extern struct ralink_soc_info soc_info;
+
+extern void ralink_of_remap(void);
+
+extern void ralink_clk_init(void);
+extern void ralink_clk_add(const char *dev, unsigned long rate);
+
+extern void ralink_rst_init(void);
+
+extern void __init prom_soc_init(struct ralink_soc_info *soc_info);
+
+__iomem void *plat_of_remap_node(const char *node);
+
+#endif /* _RALINK_COMMON_H__ */
diff --git a/arch/mips/ralink/early_printk.c b/arch/mips/ralink/early_printk.c
new file mode 100644
index 000000000..eb4fac25e
--- /dev/null
+++ b/arch/mips/ralink/early_printk.c
@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ *  Copyright (C) 2011-2012 Gabor Juhos <juhosg@openwrt.org>
+ */
+
+#include <linux/io.h>
+#include <linux/serial_reg.h>
+
+#include <asm/addrspace.h>
+#include <asm/setup.h>
+
+#ifdef CONFIG_SOC_RT288X
+#define EARLY_UART_BASE		0x300c00
+#define CHIPID_BASE		0x300004
+#elif defined(CONFIG_SOC_MT7621)
+#define EARLY_UART_BASE		0x1E000c00
+#define CHIPID_BASE		0x1E000004
+#else
+#define EARLY_UART_BASE		0x10000c00
+#define CHIPID_BASE		0x10000004
+#endif
+
+#define MT7628_CHIP_NAME1	0x20203832
+
+#define UART_REG_TX		0x04
+#define UART_REG_LCR		0x0c
+#define UART_REG_LSR		0x14
+#define UART_REG_LSR_RT2880	0x1c
+
+static __iomem void *uart_membase = (__iomem void *) KSEG1ADDR(EARLY_UART_BASE);
+static __iomem void *chipid_membase = (__iomem void *) KSEG1ADDR(CHIPID_BASE);
+static int init_complete;
+
+static inline void uart_w32(u32 val, unsigned reg)
+{
+	__raw_writel(val, uart_membase + reg);
+}
+
+static inline u32 uart_r32(unsigned reg)
+{
+	return __raw_readl(uart_membase + reg);
+}
+
+static inline int soc_is_mt7628(void)
+{
+	return IS_ENABLED(CONFIG_SOC_MT7620) &&
+		(__raw_readl(chipid_membase) == MT7628_CHIP_NAME1);
+}
+
+static void find_uart_base(void)
+{
+	int i;
+
+	if (!soc_is_mt7628())
+		return;
+
+	for (i = 0; i < 3; i++) {
+		u32 reg = uart_r32(UART_REG_LCR + (0x100 * i));
+
+		if (!reg)
+			continue;
+
+		uart_membase = (__iomem void *) KSEG1ADDR(EARLY_UART_BASE +
+							  (0x100 * i));
+		break;
+	}
+}
+
+void prom_putchar(char ch)
+{
+	if (!init_complete) {
+		find_uart_base();
+		init_complete = 1;
+	}
+
+	if (IS_ENABLED(CONFIG_SOC_MT7621) || soc_is_mt7628()) {
+		uart_w32((unsigned char)ch, UART_TX);
+		while ((uart_r32(UART_REG_LSR) & UART_LSR_THRE) == 0)
+			;
+	} else {
+		while ((uart_r32(UART_REG_LSR_RT2880) & UART_LSR_THRE) == 0)
+			;
+		uart_w32((unsigned char)ch, UART_REG_TX);
+		while ((uart_r32(UART_REG_LSR_RT2880) & UART_LSR_THRE) == 0)
+			;
+	}
+}
diff --git a/arch/mips/ralink/ill_acc.c b/arch/mips/ralink/ill_acc.c
new file mode 100644
index 000000000..f395ae218
--- /dev/null
+++ b/arch/mips/ralink/ill_acc.c
@@ -0,0 +1,89 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ * Copyright (C) 2013 John Crispin <john@phrozen.org>
+ */
+
+#include <linux/interrupt.h>
+#include <linux/of_platform.h>
+#include <linux/of_irq.h>
+
+#include <asm/mach-ralink/ralink_regs.h>
+
+#define REG_ILL_ACC_ADDR	0x10
+#define REG_ILL_ACC_TYPE	0x14
+
+#define ILL_INT_STATUS		BIT(31)
+#define ILL_ACC_WRITE		BIT(30)
+#define ILL_ACC_LEN_M		0xff
+#define ILL_ACC_OFF_M		0xf
+#define ILL_ACC_OFF_S		16
+#define ILL_ACC_ID_M		0x7
+#define ILL_ACC_ID_S		8
+
+#define	DRV_NAME		"ill_acc"
+
+static const char * const ill_acc_ids[] = {
+	"cpu", "dma", "ppe", "pdma rx", "pdma tx", "pci/e", "wmac", "usb",
+};
+
+static irqreturn_t ill_acc_irq_handler(int irq, void *_priv)
+{
+	struct device *dev = (struct device *) _priv;
+	u32 addr = rt_memc_r32(REG_ILL_ACC_ADDR);
+	u32 type = rt_memc_r32(REG_ILL_ACC_TYPE);
+
+	dev_err(dev, "illegal %s access from %s - addr:0x%08x offset:%d len:%d\n",
+		(type & ILL_ACC_WRITE) ? ("write") : ("read"),
+		ill_acc_ids[(type >> ILL_ACC_ID_S) & ILL_ACC_ID_M],
+		addr, (type >> ILL_ACC_OFF_S) & ILL_ACC_OFF_M,
+		type & ILL_ACC_LEN_M);
+
+	rt_memc_w32(ILL_INT_STATUS, REG_ILL_ACC_TYPE);
+
+	return IRQ_HANDLED;
+}
+
+static int __init ill_acc_of_setup(void)
+{
+	struct platform_device *pdev;
+	struct device_node *np;
+	int irq;
+
+	/* somehow this driver breaks on RT5350 */
+	if (of_machine_is_compatible("ralink,rt5350-soc"))
+		return -EINVAL;
+
+	np = of_find_compatible_node(NULL, NULL, "ralink,rt3050-memc");
+	if (!np)
+		return -EINVAL;
+
+	pdev = of_find_device_by_node(np);
+	if (!pdev) {
+		pr_err("%pOFn: failed to lookup pdev\n", np);
+		of_node_put(np);
+		return -EINVAL;
+	}
+
+	irq = irq_of_parse_and_map(np, 0);
+	of_node_put(np);
+	if (!irq) {
+		dev_err(&pdev->dev, "failed to get irq\n");
+		put_device(&pdev->dev);
+		return -EINVAL;
+	}
+
+	if (request_irq(irq, ill_acc_irq_handler, 0, "ill_acc", &pdev->dev)) {
+		dev_err(&pdev->dev, "failed to request irq\n");
+		put_device(&pdev->dev);
+		return -EINVAL;
+	}
+
+	rt_memc_w32(ILL_INT_STATUS, REG_ILL_ACC_TYPE);
+
+	dev_info(&pdev->dev, "irq registered\n");
+
+	return 0;
+}
+
+arch_initcall(ill_acc_of_setup);
diff --git a/arch/mips/ralink/irq-gic.c b/arch/mips/ralink/irq-gic.c
new file mode 100644
index 000000000..3bab51a5f
--- /dev/null
+++ b/arch/mips/ralink/irq-gic.c
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ * Copyright (C) 2015 Nikolay Martynov <mar.kolya@gmail.com>
+ * Copyright (C) 2015 John Crispin <john@phrozen.org>
+ */
+
+#include <linux/init.h>
+
+#include <linux/of.h>
+#include <linux/irqchip.h>
+#include <asm/mips-cps.h>
+
+int get_c0_perfcount_int(void)
+{
+	return gic_get_c0_perfcount_int();
+}
+EXPORT_SYMBOL_GPL(get_c0_perfcount_int);
+
+void __init arch_init_irq(void)
+{
+	irqchip_init();
+}
diff --git a/arch/mips/ralink/irq.c b/arch/mips/ralink/irq.c
new file mode 100644
index 000000000..fa353bc13
--- /dev/null
+++ b/arch/mips/ralink/irq.c
@@ -0,0 +1,204 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ * Copyright (C) 2009 Gabor Juhos <juhosg@openwrt.org>
+ * Copyright (C) 2013 John Crispin <john@phrozen.org>
+ */
+
+#include <linux/io.h>
+#include <linux/bitops.h>
+#include <linux/of_platform.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/irqdomain.h>
+#include <linux/interrupt.h>
+
+#include <asm/irq_cpu.h>
+#include <asm/mipsregs.h>
+
+#include "common.h"
+
+#define INTC_INT_GLOBAL		BIT(31)
+
+#define RALINK_CPU_IRQ_INTC	(MIPS_CPU_IRQ_BASE + 2)
+#define RALINK_CPU_IRQ_PCI	(MIPS_CPU_IRQ_BASE + 4)
+#define RALINK_CPU_IRQ_FE	(MIPS_CPU_IRQ_BASE + 5)
+#define RALINK_CPU_IRQ_WIFI	(MIPS_CPU_IRQ_BASE + 6)
+#define RALINK_CPU_IRQ_COUNTER	(MIPS_CPU_IRQ_BASE + 7)
+
+/* we have a cascade of 8 irqs */
+#define RALINK_INTC_IRQ_BASE	8
+
+/* we have 32 SoC irqs */
+#define RALINK_INTC_IRQ_COUNT	32
+
+#define RALINK_INTC_IRQ_PERFC   (RALINK_INTC_IRQ_BASE + 9)
+
+enum rt_intc_regs_enum {
+	INTC_REG_STATUS0 = 0,
+	INTC_REG_STATUS1,
+	INTC_REG_TYPE,
+	INTC_REG_RAW_STATUS,
+	INTC_REG_ENABLE,
+	INTC_REG_DISABLE,
+};
+
+static u32 rt_intc_regs[] = {
+	[INTC_REG_STATUS0] = 0x00,
+	[INTC_REG_STATUS1] = 0x04,
+	[INTC_REG_TYPE] = 0x20,
+	[INTC_REG_RAW_STATUS] = 0x30,
+	[INTC_REG_ENABLE] = 0x34,
+	[INTC_REG_DISABLE] = 0x38,
+};
+
+static void __iomem *rt_intc_membase;
+
+static int rt_perfcount_irq;
+
+static inline void rt_intc_w32(u32 val, unsigned reg)
+{
+	__raw_writel(val, rt_intc_membase + rt_intc_regs[reg]);
+}
+
+static inline u32 rt_intc_r32(unsigned reg)
+{
+	return __raw_readl(rt_intc_membase + rt_intc_regs[reg]);
+}
+
+static void ralink_intc_irq_unmask(struct irq_data *d)
+{
+	rt_intc_w32(BIT(d->hwirq), INTC_REG_ENABLE);
+}
+
+static void ralink_intc_irq_mask(struct irq_data *d)
+{
+	rt_intc_w32(BIT(d->hwirq), INTC_REG_DISABLE);
+}
+
+static struct irq_chip ralink_intc_irq_chip = {
+	.name		= "INTC",
+	.irq_unmask	= ralink_intc_irq_unmask,
+	.irq_mask	= ralink_intc_irq_mask,
+	.irq_mask_ack	= ralink_intc_irq_mask,
+};
+
+int get_c0_perfcount_int(void)
+{
+	return rt_perfcount_irq;
+}
+EXPORT_SYMBOL_GPL(get_c0_perfcount_int);
+
+unsigned int get_c0_compare_int(void)
+{
+	return CP0_LEGACY_COMPARE_IRQ;
+}
+
+static void ralink_intc_irq_handler(struct irq_desc *desc)
+{
+	u32 pending = rt_intc_r32(INTC_REG_STATUS0);
+
+	if (pending) {
+		struct irq_domain *domain = irq_desc_get_handler_data(desc);
+		generic_handle_domain_irq(domain, __ffs(pending));
+	} else {
+		spurious_interrupt();
+	}
+}
+
+asmlinkage void plat_irq_dispatch(void)
+{
+	unsigned long pending;
+
+	pending = read_c0_status() & read_c0_cause() & ST0_IM;
+
+	if (pending & STATUSF_IP7)
+		do_IRQ(RALINK_CPU_IRQ_COUNTER);
+
+	else if (pending & STATUSF_IP5)
+		do_IRQ(RALINK_CPU_IRQ_FE);
+
+	else if (pending & STATUSF_IP6)
+		do_IRQ(RALINK_CPU_IRQ_WIFI);
+
+	else if (pending & STATUSF_IP4)
+		do_IRQ(RALINK_CPU_IRQ_PCI);
+
+	else if (pending & STATUSF_IP2)
+		do_IRQ(RALINK_CPU_IRQ_INTC);
+
+	else
+		spurious_interrupt();
+}
+
+static int intc_map(struct irq_domain *d, unsigned int irq, irq_hw_number_t hw)
+{
+	irq_set_chip_and_handler(irq, &ralink_intc_irq_chip, handle_level_irq);
+
+	return 0;
+}
+
+static const struct irq_domain_ops irq_domain_ops = {
+	.xlate = irq_domain_xlate_onecell,
+	.map = intc_map,
+};
+
+static int __init intc_of_init(struct device_node *node,
+			       struct device_node *parent)
+{
+	struct resource res;
+	struct irq_domain *domain;
+	int irq;
+
+	if (!of_property_read_u32_array(node, "ralink,intc-registers",
+					rt_intc_regs, 6))
+		pr_info("intc: using register map from devicetree\n");
+
+	irq = irq_of_parse_and_map(node, 0);
+	if (!irq)
+		panic("Failed to get INTC IRQ");
+
+	if (of_address_to_resource(node, 0, &res))
+		panic("Failed to get intc memory range");
+
+	if (!request_mem_region(res.start, resource_size(&res),
+				res.name))
+		pr_err("Failed to request intc memory");
+
+	rt_intc_membase = ioremap(res.start,
+					resource_size(&res));
+	if (!rt_intc_membase)
+		panic("Failed to remap intc memory");
+
+	/* disable all interrupts */
+	rt_intc_w32(~0, INTC_REG_DISABLE);
+
+	/* route all INTC interrupts to MIPS HW0 interrupt */
+	rt_intc_w32(0, INTC_REG_TYPE);
+
+	domain = irq_domain_add_legacy(node, RALINK_INTC_IRQ_COUNT,
+			RALINK_INTC_IRQ_BASE, 0, &irq_domain_ops, NULL);
+	if (!domain)
+		panic("Failed to add irqdomain");
+
+	rt_intc_w32(INTC_INT_GLOBAL, INTC_REG_ENABLE);
+
+	irq_set_chained_handler_and_data(irq, ralink_intc_irq_handler, domain);
+
+	/* tell the kernel which irq is used for performance monitoring */
+	rt_perfcount_irq = irq_create_mapping(domain, 9);
+
+	return 0;
+}
+
+static struct of_device_id __initdata of_irq_ids[] = {
+	{ .compatible = "mti,cpu-interrupt-controller", .data = mips_cpu_irq_of_init },
+	{ .compatible = "ralink,rt2880-intc", .data = intc_of_init },
+	{},
+};
+
+void __init arch_init_irq(void)
+{
+	of_irq_init(of_irq_ids);
+}
+
diff --git a/arch/mips/ralink/mt7620.c b/arch/mips/ralink/mt7620.c
new file mode 100644
index 000000000..ae1fa0391
--- /dev/null
+++ b/arch/mips/ralink/mt7620.c
@@ -0,0 +1,398 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ * Parts of this file are based on Ralink's 2.6.21 BSP
+ *
+ * Copyright (C) 2008-2011 Gabor Juhos <juhosg@openwrt.org>
+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ * Copyright (C) 2013 John Crispin <john@phrozen.org>
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/bug.h>
+
+#include <asm/mipsregs.h>
+#include <asm/mach-ralink/ralink_regs.h>
+#include <asm/mach-ralink/mt7620.h>
+
+#include "common.h"
+
+/* analog */
+#define PMU0_CFG		0x88
+#define PMU_SW_SET		BIT(28)
+#define A_DCDC_EN		BIT(24)
+#define A_SSC_PERI		BIT(19)
+#define A_SSC_GEN		BIT(18)
+#define A_SSC_M			0x3
+#define A_SSC_S			16
+#define A_DLY_M			0x7
+#define A_DLY_S			8
+#define A_VTUNE_M		0xff
+
+/* digital */
+#define PMU1_CFG		0x8C
+#define DIG_SW_SEL		BIT(25)
+
+/* clock scaling */
+#define CLKCFG_FDIV_MASK	0x1f00
+#define CLKCFG_FDIV_USB_VAL	0x0300
+#define CLKCFG_FFRAC_MASK	0x001f
+#define CLKCFG_FFRAC_USB_VAL	0x0003
+
+/* EFUSE bits */
+#define EFUSE_MT7688		0x100000
+
+/* DRAM type bit */
+#define DRAM_TYPE_MT7628_MASK	0x1
+
+/* does the board have sdram or ddram */
+static int dram_type;
+
+static __init u32
+mt7620_calc_rate(u32 ref_rate, u32 mul, u32 div)
+{
+	u64 t;
+
+	t = ref_rate;
+	t *= mul;
+	do_div(t, div);
+
+	return t;
+}
+
+#define MHZ(x)		((x) * 1000 * 1000)
+
+static __init unsigned long
+mt7620_get_xtal_rate(void)
+{
+	u32 reg;
+
+	reg = rt_sysc_r32(SYSC_REG_SYSTEM_CONFIG0);
+	if (reg & SYSCFG0_XTAL_FREQ_SEL)
+		return MHZ(40);
+
+	return MHZ(20);
+}
+
+static __init unsigned long
+mt7620_get_periph_rate(unsigned long xtal_rate)
+{
+	u32 reg;
+
+	reg = rt_sysc_r32(SYSC_REG_CLKCFG0);
+	if (reg & CLKCFG0_PERI_CLK_SEL)
+		return xtal_rate;
+
+	return MHZ(40);
+}
+
+static const u32 mt7620_clk_divider[] __initconst = { 2, 3, 4, 8 };
+
+static __init unsigned long
+mt7620_get_cpu_pll_rate(unsigned long xtal_rate)
+{
+	u32 reg;
+	u32 mul;
+	u32 div;
+
+	reg = rt_sysc_r32(SYSC_REG_CPLL_CONFIG0);
+	if (reg & CPLL_CFG0_BYPASS_REF_CLK)
+		return xtal_rate;
+
+	if ((reg & CPLL_CFG0_SW_CFG) == 0)
+		return MHZ(600);
+
+	mul = (reg >> CPLL_CFG0_PLL_MULT_RATIO_SHIFT) &
+	      CPLL_CFG0_PLL_MULT_RATIO_MASK;
+	mul += 24;
+	if (reg & CPLL_CFG0_LC_CURFCK)
+		mul *= 2;
+
+	div = (reg >> CPLL_CFG0_PLL_DIV_RATIO_SHIFT) &
+	      CPLL_CFG0_PLL_DIV_RATIO_MASK;
+
+	WARN_ON(div >= ARRAY_SIZE(mt7620_clk_divider));
+
+	return mt7620_calc_rate(xtal_rate, mul, mt7620_clk_divider[div]);
+}
+
+static __init unsigned long
+mt7620_get_pll_rate(unsigned long xtal_rate, unsigned long cpu_pll_rate)
+{
+	u32 reg;
+
+	reg = rt_sysc_r32(SYSC_REG_CPLL_CONFIG1);
+	if (reg & CPLL_CFG1_CPU_AUX1)
+		return xtal_rate;
+
+	if (reg & CPLL_CFG1_CPU_AUX0)
+		return MHZ(480);
+
+	return cpu_pll_rate;
+}
+
+static __init unsigned long
+mt7620_get_cpu_rate(unsigned long pll_rate)
+{
+	u32 reg;
+	u32 mul;
+	u32 div;
+
+	reg = rt_sysc_r32(SYSC_REG_CPU_SYS_CLKCFG);
+
+	mul = reg & CPU_SYS_CLKCFG_CPU_FFRAC_MASK;
+	div = (reg >> CPU_SYS_CLKCFG_CPU_FDIV_SHIFT) &
+	      CPU_SYS_CLKCFG_CPU_FDIV_MASK;
+
+	return mt7620_calc_rate(pll_rate, mul, div);
+}
+
+static const u32 mt7620_ocp_dividers[16] __initconst = {
+	[CPU_SYS_CLKCFG_OCP_RATIO_2] = 2,
+	[CPU_SYS_CLKCFG_OCP_RATIO_3] = 3,
+	[CPU_SYS_CLKCFG_OCP_RATIO_4] = 4,
+	[CPU_SYS_CLKCFG_OCP_RATIO_5] = 5,
+	[CPU_SYS_CLKCFG_OCP_RATIO_10] = 10,
+};
+
+static __init unsigned long
+mt7620_get_dram_rate(unsigned long pll_rate)
+{
+	if (dram_type == SYSCFG0_DRAM_TYPE_SDRAM)
+		return pll_rate / 4;
+
+	return pll_rate / 3;
+}
+
+static __init unsigned long
+mt7620_get_sys_rate(unsigned long cpu_rate)
+{
+	u32 reg;
+	u32 ocp_ratio;
+	u32 div;
+
+	reg = rt_sysc_r32(SYSC_REG_CPU_SYS_CLKCFG);
+
+	ocp_ratio = (reg >> CPU_SYS_CLKCFG_OCP_RATIO_SHIFT) &
+		    CPU_SYS_CLKCFG_OCP_RATIO_MASK;
+
+	if (WARN_ON(ocp_ratio >= ARRAY_SIZE(mt7620_ocp_dividers)))
+		return cpu_rate;
+
+	div = mt7620_ocp_dividers[ocp_ratio];
+	if (WARN(!div, "invalid divider for OCP ratio %u", ocp_ratio))
+		return cpu_rate;
+
+	return cpu_rate / div;
+}
+
+void __init ralink_clk_init(void)
+{
+	unsigned long xtal_rate;
+	unsigned long cpu_pll_rate;
+	unsigned long pll_rate;
+	unsigned long cpu_rate;
+	unsigned long sys_rate;
+	unsigned long dram_rate;
+	unsigned long periph_rate;
+	unsigned long pcmi2s_rate;
+
+	xtal_rate = mt7620_get_xtal_rate();
+
+#define RFMT(label)	label ":%lu.%03luMHz "
+#define RINT(x)		((x) / 1000000)
+#define RFRAC(x)	(((x) / 1000) % 1000)
+
+	if (is_mt76x8()) {
+		if (xtal_rate == MHZ(40))
+			cpu_rate = MHZ(580);
+		else
+			cpu_rate = MHZ(575);
+		dram_rate = sys_rate = cpu_rate / 3;
+		periph_rate = MHZ(40);
+		pcmi2s_rate = MHZ(480);
+
+		ralink_clk_add("10000d00.uartlite", periph_rate);
+		ralink_clk_add("10000e00.uartlite", periph_rate);
+	} else {
+		cpu_pll_rate = mt7620_get_cpu_pll_rate(xtal_rate);
+		pll_rate = mt7620_get_pll_rate(xtal_rate, cpu_pll_rate);
+
+		cpu_rate = mt7620_get_cpu_rate(pll_rate);
+		dram_rate = mt7620_get_dram_rate(pll_rate);
+		sys_rate = mt7620_get_sys_rate(cpu_rate);
+		periph_rate = mt7620_get_periph_rate(xtal_rate);
+		pcmi2s_rate = periph_rate;
+
+		pr_debug(RFMT("XTAL") RFMT("CPU_PLL") RFMT("PLL"),
+			 RINT(xtal_rate), RFRAC(xtal_rate),
+			 RINT(cpu_pll_rate), RFRAC(cpu_pll_rate),
+			 RINT(pll_rate), RFRAC(pll_rate));
+
+		ralink_clk_add("10000500.uart", periph_rate);
+	}
+
+	pr_debug(RFMT("CPU") RFMT("DRAM") RFMT("SYS") RFMT("PERIPH"),
+		 RINT(cpu_rate), RFRAC(cpu_rate),
+		 RINT(dram_rate), RFRAC(dram_rate),
+		 RINT(sys_rate), RFRAC(sys_rate),
+		 RINT(periph_rate), RFRAC(periph_rate));
+#undef RFRAC
+#undef RINT
+#undef RFMT
+
+	ralink_clk_add("cpu", cpu_rate);
+	ralink_clk_add("10000100.timer", periph_rate);
+	ralink_clk_add("10000120.watchdog", periph_rate);
+	ralink_clk_add("10000900.i2c", periph_rate);
+	ralink_clk_add("10000a00.i2s", pcmi2s_rate);
+	ralink_clk_add("10000b00.spi", sys_rate);
+	ralink_clk_add("10000b40.spi", sys_rate);
+	ralink_clk_add("10000c00.uartlite", periph_rate);
+	ralink_clk_add("10000d00.uart1", periph_rate);
+	ralink_clk_add("10000e00.uart2", periph_rate);
+	ralink_clk_add("10180000.wmac", xtal_rate);
+
+	if (IS_ENABLED(CONFIG_USB) && !is_mt76x8()) {
+		/*
+		 * When the CPU goes into sleep mode, the BUS clock will be
+		 * too low for USB to function properly. Adjust the busses
+		 * fractional divider to fix this
+		 */
+		u32 val = rt_sysc_r32(SYSC_REG_CPU_SYS_CLKCFG);
+
+		val &= ~(CLKCFG_FDIV_MASK | CLKCFG_FFRAC_MASK);
+		val |= CLKCFG_FDIV_USB_VAL | CLKCFG_FFRAC_USB_VAL;
+
+		rt_sysc_w32(val, SYSC_REG_CPU_SYS_CLKCFG);
+	}
+}
+
+void __init ralink_of_remap(void)
+{
+	rt_sysc_membase = plat_of_remap_node("ralink,mt7620a-sysc");
+	rt_memc_membase = plat_of_remap_node("ralink,mt7620a-memc");
+
+	if (!rt_sysc_membase || !rt_memc_membase)
+		panic("Failed to remap core resources");
+}
+
+static __init void
+mt7620_dram_init(struct ralink_soc_info *soc_info)
+{
+	switch (dram_type) {
+	case SYSCFG0_DRAM_TYPE_SDRAM:
+		pr_info("Board has SDRAM\n");
+		soc_info->mem_size_min = MT7620_SDRAM_SIZE_MIN;
+		soc_info->mem_size_max = MT7620_SDRAM_SIZE_MAX;
+		break;
+
+	case SYSCFG0_DRAM_TYPE_DDR1:
+		pr_info("Board has DDR1\n");
+		soc_info->mem_size_min = MT7620_DDR1_SIZE_MIN;
+		soc_info->mem_size_max = MT7620_DDR1_SIZE_MAX;
+		break;
+
+	case SYSCFG0_DRAM_TYPE_DDR2:
+		pr_info("Board has DDR2\n");
+		soc_info->mem_size_min = MT7620_DDR2_SIZE_MIN;
+		soc_info->mem_size_max = MT7620_DDR2_SIZE_MAX;
+		break;
+	default:
+		BUG();
+	}
+}
+
+static __init void
+mt7628_dram_init(struct ralink_soc_info *soc_info)
+{
+	switch (dram_type) {
+	case SYSCFG0_DRAM_TYPE_DDR1_MT7628:
+		pr_info("Board has DDR1\n");
+		soc_info->mem_size_min = MT7620_DDR1_SIZE_MIN;
+		soc_info->mem_size_max = MT7620_DDR1_SIZE_MAX;
+		break;
+
+	case SYSCFG0_DRAM_TYPE_DDR2_MT7628:
+		pr_info("Board has DDR2\n");
+		soc_info->mem_size_min = MT7620_DDR2_SIZE_MIN;
+		soc_info->mem_size_max = MT7620_DDR2_SIZE_MAX;
+		break;
+	default:
+		BUG();
+	}
+}
+
+void __init prom_soc_init(struct ralink_soc_info *soc_info)
+{
+	void __iomem *sysc = (void __iomem *) KSEG1ADDR(MT7620_SYSC_BASE);
+	unsigned char *name = NULL;
+	u32 n0;
+	u32 n1;
+	u32 rev;
+	u32 cfg0;
+	u32 pmu0;
+	u32 pmu1;
+	u32 bga;
+
+	n0 = __raw_readl(sysc + SYSC_REG_CHIP_NAME0);
+	n1 = __raw_readl(sysc + SYSC_REG_CHIP_NAME1);
+	rev = __raw_readl(sysc + SYSC_REG_CHIP_REV);
+	bga = (rev >> CHIP_REV_PKG_SHIFT) & CHIP_REV_PKG_MASK;
+
+	if (n0 == MT7620_CHIP_NAME0 && n1 == MT7620_CHIP_NAME1) {
+		if (bga) {
+			ralink_soc = MT762X_SOC_MT7620A;
+			name = "MT7620A";
+			soc_info->compatible = "ralink,mt7620a-soc";
+		} else {
+			ralink_soc = MT762X_SOC_MT7620N;
+			name = "MT7620N";
+			soc_info->compatible = "ralink,mt7620n-soc";
+		}
+	} else if (n0 == MT7620_CHIP_NAME0 && n1 == MT7628_CHIP_NAME1) {
+		u32 efuse = __raw_readl(sysc + SYSC_REG_EFUSE_CFG);
+
+		if (efuse & EFUSE_MT7688) {
+			ralink_soc = MT762X_SOC_MT7688;
+			name = "MT7688";
+		} else {
+			ralink_soc = MT762X_SOC_MT7628AN;
+			name = "MT7628AN";
+		}
+		soc_info->compatible = "ralink,mt7628an-soc";
+	} else {
+		panic("mt762x: unknown SoC, n0:%08x n1:%08x\n", n0, n1);
+	}
+
+	snprintf(soc_info->sys_type, RAMIPS_SYS_TYPE_LEN,
+		"MediaTek %s ver:%u eco:%u",
+		name,
+		(rev >> CHIP_REV_VER_SHIFT) & CHIP_REV_VER_MASK,
+		(rev & CHIP_REV_ECO_MASK));
+
+	cfg0 = __raw_readl(sysc + SYSC_REG_SYSTEM_CONFIG0);
+	if (is_mt76x8()) {
+		dram_type = cfg0 & DRAM_TYPE_MT7628_MASK;
+	} else {
+		dram_type = (cfg0 >> SYSCFG0_DRAM_TYPE_SHIFT) &
+			    SYSCFG0_DRAM_TYPE_MASK;
+		if (dram_type == SYSCFG0_DRAM_TYPE_UNKNOWN)
+			dram_type = SYSCFG0_DRAM_TYPE_SDRAM;
+	}
+
+	soc_info->mem_base = MT7620_DRAM_BASE;
+	if (is_mt76x8())
+		mt7628_dram_init(soc_info);
+	else
+		mt7620_dram_init(soc_info);
+
+	pmu0 = __raw_readl(sysc + PMU0_CFG);
+	pmu1 = __raw_readl(sysc + PMU1_CFG);
+
+	pr_info("Analog PMU set to %s control\n",
+		(pmu0 & PMU_SW_SET) ? ("sw") : ("hw"));
+	pr_info("Digital PMU set to %s control\n",
+		(pmu1 & DIG_SW_SEL) ? ("sw") : ("hw"));
+}
diff --git a/arch/mips/ralink/mt7621.c b/arch/mips/ralink/mt7621.c
new file mode 100644
index 000000000..bbf5811af
--- /dev/null
+++ b/arch/mips/ralink/mt7621.c
@@ -0,0 +1,224 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ * Copyright (C) 2015 Nikolay Martynov <mar.kolya@gmail.com>
+ * Copyright (C) 2015 John Crispin <john@phrozen.org>
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/sys_soc.h>
+#include <linux/memblock.h>
+#include <linux/pci.h>
+#include <linux/bug.h>
+
+#include <asm/bootinfo.h>
+#include <asm/mipsregs.h>
+#include <asm/smp-ops.h>
+#include <asm/mips-cps.h>
+#include <asm/mach-ralink/ralink_regs.h>
+#include <asm/mach-ralink/mt7621.h>
+
+#include "common.h"
+
+#define MT7621_MEM_TEST_PATTERN         0xaa5555aa
+
+static u32 detect_magic __initdata;
+static struct ralink_soc_info *soc_info_ptr;
+
+int pcibios_root_bridge_prepare(struct pci_host_bridge *bridge)
+{
+	struct resource_entry *entry;
+	resource_size_t mask;
+
+	entry = resource_list_first_type(&bridge->windows, IORESOURCE_MEM);
+	if (!entry) {
+		pr_err("Cannot get memory resource\n");
+		return -EINVAL;
+	}
+
+	if (mips_cps_numiocu(0)) {
+		/*
+		 * Hardware doesn't accept mask values with 1s after
+		 * 0s (e.g. 0xffef), so warn if that's happen
+		 */
+		mask = ~(entry->res->end - entry->res->start) & CM_GCR_REGn_MASK_ADDRMASK;
+		WARN_ON(mask && BIT(ffz(~mask)) - 1 != ~mask);
+
+		write_gcr_reg1_base(entry->res->start);
+		write_gcr_reg1_mask(mask | CM_GCR_REGn_MASK_CMTGT_IOCU0);
+		pr_info("PCI coherence region base: 0x%08llx, mask/settings: 0x%08llx\n",
+			(unsigned long long)read_gcr_reg1_base(),
+			(unsigned long long)read_gcr_reg1_mask());
+	}
+
+	return 0;
+}
+
+phys_addr_t mips_cpc_default_phys_base(void)
+{
+	panic("Cannot detect cpc address");
+}
+
+static bool __init mt7621_addr_wraparound_test(phys_addr_t size)
+{
+	void *dm = (void *)KSEG1ADDR(&detect_magic);
+
+	if (CPHYSADDR(dm + size) >= MT7621_LOWMEM_MAX_SIZE)
+		return true;
+	__raw_writel(MT7621_MEM_TEST_PATTERN, dm);
+	if (__raw_readl(dm) != __raw_readl(dm + size))
+		return false;
+	__raw_writel(~MT7621_MEM_TEST_PATTERN, dm);
+	return __raw_readl(dm) == __raw_readl(dm + size);
+}
+
+static void __init mt7621_memory_detect(void)
+{
+	phys_addr_t size;
+
+	for (size = 32 * SZ_1M; size <= 256 * SZ_1M; size <<= 1) {
+		if (mt7621_addr_wraparound_test(size)) {
+			memblock_add(MT7621_LOWMEM_BASE, size);
+			return;
+		}
+	}
+
+	memblock_add(MT7621_LOWMEM_BASE, MT7621_LOWMEM_MAX_SIZE);
+	memblock_add(MT7621_HIGHMEM_BASE, MT7621_HIGHMEM_SIZE);
+}
+
+void __init ralink_of_remap(void)
+{
+	rt_sysc_membase = plat_of_remap_node("mediatek,mt7621-sysc");
+	rt_memc_membase = plat_of_remap_node("mediatek,mt7621-memc");
+
+	if (!rt_sysc_membase || !rt_memc_membase)
+		panic("Failed to remap core resources");
+}
+
+static unsigned int __init mt7621_get_soc_name0(void)
+{
+	return __raw_readl(MT7621_SYSC_BASE + SYSC_REG_CHIP_NAME0);
+}
+
+static unsigned int __init mt7621_get_soc_name1(void)
+{
+	return __raw_readl(MT7621_SYSC_BASE + SYSC_REG_CHIP_NAME1);
+}
+
+static bool __init mt7621_soc_valid(void)
+{
+	if (mt7621_get_soc_name0() == MT7621_CHIP_NAME0 &&
+			mt7621_get_soc_name1() == MT7621_CHIP_NAME1)
+		return true;
+	else
+		return false;
+}
+
+static const char __init *mt7621_get_soc_id(void)
+{
+	if (mt7621_soc_valid())
+		return "MT7621";
+	else
+		return "invalid";
+}
+
+static unsigned int __init mt7621_get_soc_rev(void)
+{
+	return __raw_readl(MT7621_SYSC_BASE + SYSC_REG_CHIP_REV);
+}
+
+static unsigned int __init mt7621_get_soc_ver(void)
+{
+	return (mt7621_get_soc_rev() >> CHIP_REV_VER_SHIFT) & CHIP_REV_VER_MASK;
+}
+
+static unsigned int __init mt7621_get_soc_eco(void)
+{
+	return (mt7621_get_soc_rev() & CHIP_REV_ECO_MASK);
+}
+
+static const char __init *mt7621_get_soc_revision(void)
+{
+	if (mt7621_get_soc_rev() == 1 && mt7621_get_soc_eco() == 1)
+		return "E2";
+	else
+		return "E1";
+}
+
+static int __init mt7621_soc_dev_init(void)
+{
+	struct soc_device *soc_dev;
+	struct soc_device_attribute *soc_dev_attr;
+
+	soc_dev_attr = kzalloc(sizeof(*soc_dev_attr), GFP_KERNEL);
+	if (!soc_dev_attr)
+		return -ENOMEM;
+
+	soc_dev_attr->soc_id = "mt7621";
+	soc_dev_attr->family = "Ralink";
+	soc_dev_attr->revision = mt7621_get_soc_revision();
+
+	soc_dev_attr->data = soc_info_ptr;
+
+	soc_dev = soc_device_register(soc_dev_attr);
+	if (IS_ERR(soc_dev)) {
+		kfree(soc_dev_attr);
+		return PTR_ERR(soc_dev);
+	}
+
+	return 0;
+}
+device_initcall(mt7621_soc_dev_init);
+
+void __init prom_soc_init(struct ralink_soc_info *soc_info)
+{
+	/* Early detection of CMP support */
+	mips_cm_probe();
+	mips_cpc_probe();
+
+	if (mips_cps_numiocu(0)) {
+		/*
+		 * mips_cm_probe() wipes out bootloader
+		 * config for CM regions and we have to configure them
+		 * again. This SoC cannot talk to pamlbus devices
+		 * witout proper iocu region set up.
+		 *
+		 * FIXME: it would be better to do this with values
+		 * from DT, but we need this very early because
+		 * without this we cannot talk to pretty much anything
+		 * including serial.
+		 */
+		write_gcr_reg0_base(MT7621_PALMBUS_BASE);
+		write_gcr_reg0_mask(~MT7621_PALMBUS_SIZE |
+				    CM_GCR_REGn_MASK_CMTGT_IOCU0);
+		__sync();
+	}
+
+	if (mt7621_soc_valid())
+		soc_info->compatible = "mediatek,mt7621-soc";
+	else
+		panic("mt7621: unknown SoC, n0:%08x n1:%08x\n",
+				mt7621_get_soc_name0(),
+				mt7621_get_soc_name1());
+	ralink_soc = MT762X_SOC_MT7621AT;
+
+	snprintf(soc_info->sys_type, RAMIPS_SYS_TYPE_LEN,
+		"MediaTek %s ver:%u eco:%u",
+		mt7621_get_soc_id(),
+		mt7621_get_soc_ver(),
+		mt7621_get_soc_eco());
+
+	soc_info->mem_detect = mt7621_memory_detect;
+
+	soc_info_ptr = soc_info;
+
+	if (!register_cps_smp_ops())
+		return;
+	if (!register_cmp_smp_ops())
+		return;
+	if (!register_vsmp_smp_ops())
+		return;
+}
diff --git a/arch/mips/ralink/of.c b/arch/mips/ralink/of.c
new file mode 100644
index 000000000..4d06de77d
--- /dev/null
+++ b/arch/mips/ralink/of.c
@@ -0,0 +1,91 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ * Copyright (C) 2008-2009 Gabor Juhos <juhosg@openwrt.org>
+ * Copyright (C) 2013 John Crispin <john@phrozen.org>
+ */
+
+#include <linux/io.h>
+#include <linux/clk.h>
+#include <linux/export.h>
+#include <linux/init.h>
+#include <linux/sizes.h>
+#include <linux/of_fdt.h>
+#include <linux/kernel.h>
+#include <linux/memblock.h>
+#include <linux/of_platform.h>
+#include <linux/of_address.h>
+
+#include <asm/reboot.h>
+#include <asm/bootinfo.h>
+#include <asm/addrspace.h>
+#include <asm/prom.h>
+#include <asm/mach-ralink/ralink_regs.h>
+
+#include "common.h"
+
+__iomem void *rt_sysc_membase;
+__iomem void *rt_memc_membase;
+EXPORT_SYMBOL_GPL(rt_sysc_membase);
+
+__iomem void *plat_of_remap_node(const char *node)
+{
+	struct resource res;
+	struct device_node *np;
+
+	np = of_find_compatible_node(NULL, NULL, node);
+	if (!np)
+		panic("Failed to find %s node", node);
+
+	if (of_address_to_resource(np, 0, &res))
+		panic("Failed to get resource for %s", node);
+
+	of_node_put(np);
+
+	if (!request_mem_region(res.start,
+				resource_size(&res),
+				res.name))
+		panic("Failed to request resources for %s", node);
+
+	return ioremap(res.start, resource_size(&res));
+}
+
+void __init plat_mem_setup(void)
+{
+	void *dtb;
+
+	set_io_port_base(KSEG1);
+
+	/*
+	 * Load the builtin devicetree. This causes the chosen node to be
+	 * parsed resulting in our memory appearing.
+	 */
+	dtb = get_fdt();
+	__dt_setup_arch(dtb);
+
+	if (early_init_dt_scan_memory())
+		return;
+
+	if (soc_info.mem_detect)
+		soc_info.mem_detect();
+	else if (soc_info.mem_size)
+		memblock_add(soc_info.mem_base, soc_info.mem_size * SZ_1M);
+	else
+		detect_memory_region(soc_info.mem_base,
+				     soc_info.mem_size_min * SZ_1M,
+				     soc_info.mem_size_max * SZ_1M);
+}
+
+static int __init plat_of_setup(void)
+{
+	__dt_register_buses(soc_info.compatible, "palmbus");
+
+	/* make sure that the reset controller is setup early */
+	if (ralink_soc != MT762X_SOC_MT7621AT)
+		ralink_rst_init();
+
+	return 0;
+}
+
+arch_initcall(plat_of_setup);
diff --git a/arch/mips/ralink/prom.c b/arch/mips/ralink/prom.c
new file mode 100644
index 000000000..aaac1e6ec
--- /dev/null
+++ b/arch/mips/ralink/prom.c
@@ -0,0 +1,67 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ *  Copyright (C) 2009 Gabor Juhos <juhosg@openwrt.org>
+ *  Copyright (C) 2010 Joonas Lahtinen <joonas.lahtinen@gmail.com>
+ *  Copyright (C) 2013 John Crispin <john@phrozen.org>
+ */
+
+#include <linux/string.h>
+#include <linux/of_fdt.h>
+#include <linux/of_platform.h>
+
+#include <asm/bootinfo.h>
+#include <asm/addrspace.h>
+
+#include <asm/mach-ralink/ralink_regs.h>
+
+#include "common.h"
+
+struct ralink_soc_info soc_info;
+
+enum ralink_soc_type ralink_soc;
+EXPORT_SYMBOL_GPL(ralink_soc);
+
+const char *get_system_type(void)
+{
+	return soc_info.sys_type;
+}
+
+static __init void prom_init_cmdline(void)
+{
+	int argc;
+	char **argv;
+	int i;
+
+	pr_debug("prom: fw_arg0=%08x fw_arg1=%08x fw_arg2=%08x fw_arg3=%08x\n",
+	       (unsigned int)fw_arg0, (unsigned int)fw_arg1,
+	       (unsigned int)fw_arg2, (unsigned int)fw_arg3);
+
+	argc = fw_arg0;
+	argv = (char **) KSEG1ADDR(fw_arg1);
+
+	if (!argv) {
+		pr_debug("argv=%p is invalid, skipping\n",
+		       argv);
+		return;
+	}
+
+	for (i = 0; i < argc; i++) {
+		char *p = (char *) KSEG1ADDR(argv[i]);
+
+		if (CPHYSADDR(p) && *p) {
+			pr_debug("argv[%d]: %s\n", i, p);
+			strlcat(arcs_cmdline, " ", sizeof(arcs_cmdline));
+			strlcat(arcs_cmdline, p, sizeof(arcs_cmdline));
+		}
+	}
+}
+
+void __init prom_init(void)
+{
+	prom_soc_init(&soc_info);
+
+	pr_info("SoC Type: %s\n", get_system_type());
+
+	prom_init_cmdline();
+}
diff --git a/arch/mips/ralink/reset.c b/arch/mips/ralink/reset.c
new file mode 100644
index 000000000..274d33078
--- /dev/null
+++ b/arch/mips/ralink/reset.c
@@ -0,0 +1,104 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ * Copyright (C) 2008-2009 Gabor Juhos <juhosg@openwrt.org>
+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ * Copyright (C) 2013 John Crispin <john@phrozen.org>
+ */
+
+#include <linux/pm.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/delay.h>
+#include <linux/reset-controller.h>
+
+#include <asm/reboot.h>
+
+#include <asm/mach-ralink/ralink_regs.h>
+
+/* Reset Control */
+#define SYSC_REG_RESET_CTRL	0x034
+
+#define RSTCTL_RESET_PCI	BIT(26)
+#define RSTCTL_RESET_SYSTEM	BIT(0)
+
+static int ralink_assert_device(struct reset_controller_dev *rcdev,
+				unsigned long id)
+{
+	u32 val;
+
+	if (id == 0)
+		return -1;
+
+	val = rt_sysc_r32(SYSC_REG_RESET_CTRL);
+	val |= BIT(id);
+	rt_sysc_w32(val, SYSC_REG_RESET_CTRL);
+
+	return 0;
+}
+
+static int ralink_deassert_device(struct reset_controller_dev *rcdev,
+				  unsigned long id)
+{
+	u32 val;
+
+	if (id == 0)
+		return -1;
+
+	val = rt_sysc_r32(SYSC_REG_RESET_CTRL);
+	val &= ~BIT(id);
+	rt_sysc_w32(val, SYSC_REG_RESET_CTRL);
+
+	return 0;
+}
+
+static int ralink_reset_device(struct reset_controller_dev *rcdev,
+			       unsigned long id)
+{
+	ralink_assert_device(rcdev, id);
+	return ralink_deassert_device(rcdev, id);
+}
+
+static const struct reset_control_ops reset_ops = {
+	.reset = ralink_reset_device,
+	.assert = ralink_assert_device,
+	.deassert = ralink_deassert_device,
+};
+
+static struct reset_controller_dev reset_dev = {
+	.ops			= &reset_ops,
+	.owner			= THIS_MODULE,
+	.nr_resets		= 32,
+	.of_reset_n_cells	= 1,
+};
+
+void ralink_rst_init(void)
+{
+	reset_dev.of_node = of_find_compatible_node(NULL, NULL,
+						"ralink,rt2880-reset");
+	if (!reset_dev.of_node)
+		pr_err("Failed to find reset controller node");
+	else
+		reset_controller_register(&reset_dev);
+}
+
+static void ralink_restart(char *command)
+{
+	if (IS_ENABLED(CONFIG_PCI)) {
+		rt_sysc_m32(0, RSTCTL_RESET_PCI, SYSC_REG_RESET_CTRL);
+		mdelay(50);
+	}
+
+	local_irq_disable();
+	rt_sysc_w32(RSTCTL_RESET_SYSTEM, SYSC_REG_RESET_CTRL);
+	unreachable();
+}
+
+static int __init mips_reboot_setup(void)
+{
+	_machine_restart = ralink_restart;
+
+	return 0;
+}
+
+arch_initcall(mips_reboot_setup);
diff --git a/arch/mips/ralink/rt288x.c b/arch/mips/ralink/rt288x.c
new file mode 100644
index 000000000..493335db2
--- /dev/null
+++ b/arch/mips/ralink/rt288x.c
@@ -0,0 +1,90 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ * Parts of this file are based on Ralink's 2.6.21 BSP
+ *
+ * Copyright (C) 2008-2011 Gabor Juhos <juhosg@openwrt.org>
+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ * Copyright (C) 2013 John Crispin <john@phrozen.org>
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+
+#include <asm/mipsregs.h>
+#include <asm/mach-ralink/ralink_regs.h>
+#include <asm/mach-ralink/rt288x.h>
+
+#include "common.h"
+
+void __init ralink_clk_init(void)
+{
+	unsigned long cpu_rate, wmac_rate = 40000000;
+	u32 t = rt_sysc_r32(SYSC_REG_SYSTEM_CONFIG);
+	t = ((t >> SYSTEM_CONFIG_CPUCLK_SHIFT) & SYSTEM_CONFIG_CPUCLK_MASK);
+
+	switch (t) {
+	case SYSTEM_CONFIG_CPUCLK_250:
+		cpu_rate = 250000000;
+		break;
+	case SYSTEM_CONFIG_CPUCLK_266:
+		cpu_rate = 266666667;
+		break;
+	case SYSTEM_CONFIG_CPUCLK_280:
+		cpu_rate = 280000000;
+		break;
+	case SYSTEM_CONFIG_CPUCLK_300:
+		cpu_rate = 300000000;
+		break;
+	}
+
+	ralink_clk_add("cpu", cpu_rate);
+	ralink_clk_add("300100.timer", cpu_rate / 2);
+	ralink_clk_add("300120.watchdog", cpu_rate / 2);
+	ralink_clk_add("300500.uart", cpu_rate / 2);
+	ralink_clk_add("300900.i2c", cpu_rate / 2);
+	ralink_clk_add("300c00.uartlite", cpu_rate / 2);
+	ralink_clk_add("400000.ethernet", cpu_rate / 2);
+	ralink_clk_add("480000.wmac", wmac_rate);
+}
+
+void __init ralink_of_remap(void)
+{
+	rt_sysc_membase = plat_of_remap_node("ralink,rt2880-sysc");
+	rt_memc_membase = plat_of_remap_node("ralink,rt2880-memc");
+
+	if (!rt_sysc_membase || !rt_memc_membase)
+		panic("Failed to remap core resources");
+}
+
+void __init prom_soc_init(struct ralink_soc_info *soc_info)
+{
+	void __iomem *sysc = (void __iomem *) KSEG1ADDR(RT2880_SYSC_BASE);
+	const char *name;
+	u32 n0;
+	u32 n1;
+	u32 id;
+
+	n0 = __raw_readl(sysc + SYSC_REG_CHIP_NAME0);
+	n1 = __raw_readl(sysc + SYSC_REG_CHIP_NAME1);
+	id = __raw_readl(sysc + SYSC_REG_CHIP_ID);
+
+	if (n0 == RT2880_CHIP_NAME0 && n1 == RT2880_CHIP_NAME1) {
+		soc_info->compatible = "ralink,r2880-soc";
+		name = "RT2880";
+	} else {
+		panic("rt288x: unknown SoC, n0:%08x n1:%08x", n0, n1);
+	}
+
+	snprintf(soc_info->sys_type, RAMIPS_SYS_TYPE_LEN,
+		"Ralink %s id:%u rev:%u",
+		name,
+		(id >> CHIP_ID_ID_SHIFT) & CHIP_ID_ID_MASK,
+		(id & CHIP_ID_REV_MASK));
+
+	soc_info->mem_base = RT2880_SDRAM_BASE;
+	soc_info->mem_size_min = RT2880_MEM_SIZE_MIN;
+	soc_info->mem_size_max = RT2880_MEM_SIZE_MAX;
+
+	ralink_soc = RT2880_SOC;
+}
diff --git a/arch/mips/ralink/rt305x.c b/arch/mips/ralink/rt305x.c
new file mode 100644
index 000000000..8b095a9dc
--- /dev/null
+++ b/arch/mips/ralink/rt305x.c
@@ -0,0 +1,201 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ * Parts of this file are based on Ralink's 2.6.21 BSP
+ *
+ * Copyright (C) 2008-2011 Gabor Juhos <juhosg@openwrt.org>
+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ * Copyright (C) 2013 John Crispin <john@phrozen.org>
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/bug.h>
+
+#include <asm/io.h>
+#include <asm/mipsregs.h>
+#include <asm/mach-ralink/ralink_regs.h>
+#include <asm/mach-ralink/rt305x.h>
+
+#include "common.h"
+
+static unsigned long rt5350_get_mem_size(void)
+{
+	void __iomem *sysc = (void __iomem *) KSEG1ADDR(RT305X_SYSC_BASE);
+	unsigned long ret;
+	u32 t;
+
+	t = __raw_readl(sysc + SYSC_REG_SYSTEM_CONFIG);
+	t = (t >> RT5350_SYSCFG0_DRAM_SIZE_SHIFT) &
+		RT5350_SYSCFG0_DRAM_SIZE_MASK;
+
+	switch (t) {
+	case RT5350_SYSCFG0_DRAM_SIZE_2M:
+		ret = 2;
+		break;
+	case RT5350_SYSCFG0_DRAM_SIZE_8M:
+		ret = 8;
+		break;
+	case RT5350_SYSCFG0_DRAM_SIZE_16M:
+		ret = 16;
+		break;
+	case RT5350_SYSCFG0_DRAM_SIZE_32M:
+		ret = 32;
+		break;
+	case RT5350_SYSCFG0_DRAM_SIZE_64M:
+		ret = 64;
+		break;
+	default:
+		panic("rt5350: invalid DRAM size: %u", t);
+		break;
+	}
+
+	return ret;
+}
+
+void __init ralink_clk_init(void)
+{
+	unsigned long cpu_rate, sys_rate, wdt_rate, uart_rate;
+	unsigned long wmac_rate = 40000000;
+
+	u32 t = rt_sysc_r32(SYSC_REG_SYSTEM_CONFIG);
+
+	if (soc_is_rt305x() || soc_is_rt3350()) {
+		t = (t >> RT305X_SYSCFG_CPUCLK_SHIFT) &
+		     RT305X_SYSCFG_CPUCLK_MASK;
+		switch (t) {
+		case RT305X_SYSCFG_CPUCLK_LOW:
+			cpu_rate = 320000000;
+			break;
+		case RT305X_SYSCFG_CPUCLK_HIGH:
+			cpu_rate = 384000000;
+			break;
+		}
+		sys_rate = uart_rate = wdt_rate = cpu_rate / 3;
+	} else if (soc_is_rt3352()) {
+		t = (t >> RT3352_SYSCFG0_CPUCLK_SHIFT) &
+		     RT3352_SYSCFG0_CPUCLK_MASK;
+		switch (t) {
+		case RT3352_SYSCFG0_CPUCLK_LOW:
+			cpu_rate = 384000000;
+			break;
+		case RT3352_SYSCFG0_CPUCLK_HIGH:
+			cpu_rate = 400000000;
+			break;
+		}
+		sys_rate = wdt_rate = cpu_rate / 3;
+		uart_rate = 40000000;
+	} else if (soc_is_rt5350()) {
+		t = (t >> RT5350_SYSCFG0_CPUCLK_SHIFT) &
+		     RT5350_SYSCFG0_CPUCLK_MASK;
+		switch (t) {
+		case RT5350_SYSCFG0_CPUCLK_360:
+			cpu_rate = 360000000;
+			sys_rate = cpu_rate / 3;
+			break;
+		case RT5350_SYSCFG0_CPUCLK_320:
+			cpu_rate = 320000000;
+			sys_rate = cpu_rate / 4;
+			break;
+		case RT5350_SYSCFG0_CPUCLK_300:
+			cpu_rate = 300000000;
+			sys_rate = cpu_rate / 3;
+			break;
+		default:
+			BUG();
+		}
+		uart_rate = 40000000;
+		wdt_rate = sys_rate;
+	} else {
+		BUG();
+	}
+
+	if (soc_is_rt3352() || soc_is_rt5350()) {
+		u32 val = rt_sysc_r32(RT3352_SYSC_REG_SYSCFG0);
+
+		if (!(val & RT3352_CLKCFG0_XTAL_SEL))
+			wmac_rate = 20000000;
+	}
+
+	ralink_clk_add("cpu", cpu_rate);
+	ralink_clk_add("sys", sys_rate);
+	ralink_clk_add("10000900.i2c", uart_rate);
+	ralink_clk_add("10000a00.i2s", uart_rate);
+	ralink_clk_add("10000b00.spi", sys_rate);
+	ralink_clk_add("10000b40.spi", sys_rate);
+	ralink_clk_add("10000100.timer", wdt_rate);
+	ralink_clk_add("10000120.watchdog", wdt_rate);
+	ralink_clk_add("10000500.uart", uart_rate);
+	ralink_clk_add("10000c00.uartlite", uart_rate);
+	ralink_clk_add("10100000.ethernet", sys_rate);
+	ralink_clk_add("10180000.wmac", wmac_rate);
+}
+
+void __init ralink_of_remap(void)
+{
+	rt_sysc_membase = plat_of_remap_node("ralink,rt3050-sysc");
+	rt_memc_membase = plat_of_remap_node("ralink,rt3050-memc");
+
+	if (!rt_sysc_membase || !rt_memc_membase)
+		panic("Failed to remap core resources");
+}
+
+void __init prom_soc_init(struct ralink_soc_info *soc_info)
+{
+	void __iomem *sysc = (void __iomem *) KSEG1ADDR(RT305X_SYSC_BASE);
+	unsigned char *name;
+	u32 n0;
+	u32 n1;
+	u32 id;
+
+	n0 = __raw_readl(sysc + SYSC_REG_CHIP_NAME0);
+	n1 = __raw_readl(sysc + SYSC_REG_CHIP_NAME1);
+
+	if (n0 == RT3052_CHIP_NAME0 && n1 == RT3052_CHIP_NAME1) {
+		unsigned long icache_sets;
+
+		icache_sets = (read_c0_config1() >> 22) & 7;
+		if (icache_sets == 1) {
+			ralink_soc = RT305X_SOC_RT3050;
+			name = "RT3050";
+			soc_info->compatible = "ralink,rt3050-soc";
+		} else {
+			ralink_soc = RT305X_SOC_RT3052;
+			name = "RT3052";
+			soc_info->compatible = "ralink,rt3052-soc";
+		}
+	} else if (n0 == RT3350_CHIP_NAME0 && n1 == RT3350_CHIP_NAME1) {
+		ralink_soc = RT305X_SOC_RT3350;
+		name = "RT3350";
+		soc_info->compatible = "ralink,rt3350-soc";
+	} else if (n0 == RT3352_CHIP_NAME0 && n1 == RT3352_CHIP_NAME1) {
+		ralink_soc = RT305X_SOC_RT3352;
+		name = "RT3352";
+		soc_info->compatible = "ralink,rt3352-soc";
+	} else if (n0 == RT5350_CHIP_NAME0 && n1 == RT5350_CHIP_NAME1) {
+		ralink_soc = RT305X_SOC_RT5350;
+		name = "RT5350";
+		soc_info->compatible = "ralink,rt5350-soc";
+	} else {
+		panic("rt305x: unknown SoC, n0:%08x n1:%08x", n0, n1);
+	}
+
+	id = __raw_readl(sysc + SYSC_REG_CHIP_ID);
+
+	snprintf(soc_info->sys_type, RAMIPS_SYS_TYPE_LEN,
+		"Ralink %s id:%u rev:%u",
+		name,
+		(id >> CHIP_ID_ID_SHIFT) & CHIP_ID_ID_MASK,
+		(id & CHIP_ID_REV_MASK));
+
+	soc_info->mem_base = RT305X_SDRAM_BASE;
+	if (soc_is_rt5350()) {
+		soc_info->mem_size = rt5350_get_mem_size();
+	} else if (soc_is_rt305x() || soc_is_rt3350()) {
+		soc_info->mem_size_min = RT305X_MEM_SIZE_MIN;
+		soc_info->mem_size_max = RT305X_MEM_SIZE_MAX;
+	} else if (soc_is_rt3352()) {
+		soc_info->mem_size_min = RT3352_MEM_SIZE_MIN;
+		soc_info->mem_size_max = RT3352_MEM_SIZE_MAX;
+	}
+}
diff --git a/arch/mips/ralink/rt3883.c b/arch/mips/ralink/rt3883.c
new file mode 100644
index 000000000..d9875f146
--- /dev/null
+++ b/arch/mips/ralink/rt3883.c
@@ -0,0 +1,103 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ * Parts of this file are based on Ralink's 2.6.21 BSP
+ *
+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ * Copyright (C) 2008-2011 Gabor Juhos <juhosg@openwrt.org>
+ * Copyright (C) 2013 John Crispin <john@phrozen.org>
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+
+#include <asm/mipsregs.h>
+#include <asm/mach-ralink/ralink_regs.h>
+#include <asm/mach-ralink/rt3883.h>
+
+#include "common.h"
+
+void __init ralink_clk_init(void)
+{
+	unsigned long cpu_rate, sys_rate;
+	u32 syscfg0;
+	u32 clksel;
+	u32 ddr2;
+
+	syscfg0 = rt_sysc_r32(RT3883_SYSC_REG_SYSCFG0);
+	clksel = ((syscfg0 >> RT3883_SYSCFG0_CPUCLK_SHIFT) &
+		RT3883_SYSCFG0_CPUCLK_MASK);
+	ddr2 = syscfg0 & RT3883_SYSCFG0_DRAM_TYPE_DDR2;
+
+	switch (clksel) {
+	case RT3883_SYSCFG0_CPUCLK_250:
+		cpu_rate = 250000000;
+		sys_rate = (ddr2) ? 125000000 : 83000000;
+		break;
+	case RT3883_SYSCFG0_CPUCLK_384:
+		cpu_rate = 384000000;
+		sys_rate = (ddr2) ? 128000000 : 96000000;
+		break;
+	case RT3883_SYSCFG0_CPUCLK_480:
+		cpu_rate = 480000000;
+		sys_rate = (ddr2) ? 160000000 : 120000000;
+		break;
+	case RT3883_SYSCFG0_CPUCLK_500:
+		cpu_rate = 500000000;
+		sys_rate = (ddr2) ? 166000000 : 125000000;
+		break;
+	}
+
+	ralink_clk_add("cpu", cpu_rate);
+	ralink_clk_add("10000100.timer", sys_rate);
+	ralink_clk_add("10000120.watchdog", sys_rate);
+	ralink_clk_add("10000500.uart", 40000000);
+	ralink_clk_add("10000900.i2c", 40000000);
+	ralink_clk_add("10000a00.i2s", 40000000);
+	ralink_clk_add("10000b00.spi", sys_rate);
+	ralink_clk_add("10000b40.spi", sys_rate);
+	ralink_clk_add("10000c00.uartlite", 40000000);
+	ralink_clk_add("10100000.ethernet", sys_rate);
+	ralink_clk_add("10180000.wmac", 40000000);
+}
+
+void __init ralink_of_remap(void)
+{
+	rt_sysc_membase = plat_of_remap_node("ralink,rt3883-sysc");
+	rt_memc_membase = plat_of_remap_node("ralink,rt3883-memc");
+
+	if (!rt_sysc_membase || !rt_memc_membase)
+		panic("Failed to remap core resources");
+}
+
+void __init prom_soc_init(struct ralink_soc_info *soc_info)
+{
+	void __iomem *sysc = (void __iomem *) KSEG1ADDR(RT3883_SYSC_BASE);
+	const char *name;
+	u32 n0;
+	u32 n1;
+	u32 id;
+
+	n0 = __raw_readl(sysc + RT3883_SYSC_REG_CHIPID0_3);
+	n1 = __raw_readl(sysc + RT3883_SYSC_REG_CHIPID4_7);
+	id = __raw_readl(sysc + RT3883_SYSC_REG_REVID);
+
+	if (n0 == RT3883_CHIP_NAME0 && n1 == RT3883_CHIP_NAME1) {
+		soc_info->compatible = "ralink,rt3883-soc";
+		name = "RT3883";
+	} else {
+		panic("rt3883: unknown SoC, n0:%08x n1:%08x", n0, n1);
+	}
+
+	snprintf(soc_info->sys_type, RAMIPS_SYS_TYPE_LEN,
+		"Ralink %s ver:%u eco:%u",
+		name,
+		(id >> RT3883_REVID_VER_ID_SHIFT) & RT3883_REVID_VER_ID_MASK,
+		(id & RT3883_REVID_ECO_ID_MASK));
+
+	soc_info->mem_base = RT3883_SDRAM_BASE;
+	soc_info->mem_size_min = RT3883_MEM_SIZE_MIN;
+	soc_info->mem_size_max = RT3883_MEM_SIZE_MAX;
+
+	ralink_soc = RT3883_SOC;
+}
diff --git a/arch/mips/ralink/timer-gic.c b/arch/mips/ralink/timer-gic.c
new file mode 100644
index 000000000..dcf2a44ac
--- /dev/null
+++ b/arch/mips/ralink/timer-gic.c
@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *
+ * Copyright (C) 2015 Nikolay Martynov <mar.kolya@gmail.com>
+ * Copyright (C) 2015 John Crispin <john@phrozen.org>
+ */
+
+#include <linux/init.h>
+
+#include <linux/of.h>
+#include <linux/of_clk.h>
+#include <linux/clocksource.h>
+
+#include "common.h"
+
+void __init plat_time_init(void)
+{
+	ralink_of_remap();
+
+	of_clk_init(NULL);
+	timer_probe();
+}
diff --git a/arch/mips/ralink/timer.c b/arch/mips/ralink/timer.c
new file mode 100644
index 000000000..652424d8e
--- /dev/null
+++ b/arch/mips/ralink/timer.c
@@ -0,0 +1,151 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Ralink RT2880 timer
+ * Author: John Crispin
+ *
+ * Copyright (C) 2013 John Crispin <john@phrozen.org>
+*/
+
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/timer.h>
+#include <linux/of_gpio.h>
+#include <linux/clk.h>
+
+#include <asm/mach-ralink/ralink_regs.h>
+
+#define TIMER_REG_TMRSTAT		0x00
+#define TIMER_REG_TMR0LOAD		0x10
+#define TIMER_REG_TMR0CTL		0x18
+
+#define TMRSTAT_TMR0INT			BIT(0)
+
+#define TMR0CTL_ENABLE			BIT(7)
+#define TMR0CTL_MODE_PERIODIC		BIT(4)
+#define TMR0CTL_PRESCALER		1
+#define TMR0CTL_PRESCALE_VAL		(0xf - TMR0CTL_PRESCALER)
+#define TMR0CTL_PRESCALE_DIV		(65536 / BIT(TMR0CTL_PRESCALER))
+
+struct rt_timer {
+	struct device	*dev;
+	void __iomem	*membase;
+	int		irq;
+	unsigned long	timer_freq;
+	unsigned long	timer_div;
+};
+
+static inline void rt_timer_w32(struct rt_timer *rt, u8 reg, u32 val)
+{
+	__raw_writel(val, rt->membase + reg);
+}
+
+static inline u32 rt_timer_r32(struct rt_timer *rt, u8 reg)
+{
+	return __raw_readl(rt->membase + reg);
+}
+
+static irqreturn_t rt_timer_irq(int irq, void *_rt)
+{
+	struct rt_timer *rt =  (struct rt_timer *) _rt;
+
+	rt_timer_w32(rt, TIMER_REG_TMR0LOAD, rt->timer_freq / rt->timer_div);
+	rt_timer_w32(rt, TIMER_REG_TMRSTAT, TMRSTAT_TMR0INT);
+
+	return IRQ_HANDLED;
+}
+
+
+static int rt_timer_request(struct rt_timer *rt)
+{
+	int err = request_irq(rt->irq, rt_timer_irq, 0,
+						dev_name(rt->dev), rt);
+	if (err) {
+		dev_err(rt->dev, "failed to request irq\n");
+	} else {
+		u32 t = TMR0CTL_MODE_PERIODIC | TMR0CTL_PRESCALE_VAL;
+		rt_timer_w32(rt, TIMER_REG_TMR0CTL, t);
+	}
+	return err;
+}
+
+static int rt_timer_config(struct rt_timer *rt, unsigned long divisor)
+{
+	if (rt->timer_freq < divisor)
+		rt->timer_div = rt->timer_freq;
+	else
+		rt->timer_div = divisor;
+
+	rt_timer_w32(rt, TIMER_REG_TMR0LOAD, rt->timer_freq / rt->timer_div);
+
+	return 0;
+}
+
+static int rt_timer_enable(struct rt_timer *rt)
+{
+	u32 t;
+
+	rt_timer_w32(rt, TIMER_REG_TMR0LOAD, rt->timer_freq / rt->timer_div);
+
+	t = rt_timer_r32(rt, TIMER_REG_TMR0CTL);
+	t |= TMR0CTL_ENABLE;
+	rt_timer_w32(rt, TIMER_REG_TMR0CTL, t);
+
+	return 0;
+}
+
+static int rt_timer_probe(struct platform_device *pdev)
+{
+	struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	struct rt_timer *rt;
+	struct clk *clk;
+
+	rt = devm_kzalloc(&pdev->dev, sizeof(*rt), GFP_KERNEL);
+	if (!rt) {
+		dev_err(&pdev->dev, "failed to allocate memory\n");
+		return -ENOMEM;
+	}
+
+	rt->irq = platform_get_irq(pdev, 0);
+	if (rt->irq < 0)
+		return rt->irq;
+
+	rt->membase = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(rt->membase))
+		return PTR_ERR(rt->membase);
+
+	clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(clk)) {
+		dev_err(&pdev->dev, "failed get clock rate\n");
+		return PTR_ERR(clk);
+	}
+
+	rt->timer_freq = clk_get_rate(clk) / TMR0CTL_PRESCALE_DIV;
+	if (!rt->timer_freq)
+		return -EINVAL;
+
+	rt->dev = &pdev->dev;
+	platform_set_drvdata(pdev, rt);
+
+	rt_timer_request(rt);
+	rt_timer_config(rt, 2);
+	rt_timer_enable(rt);
+
+	dev_info(&pdev->dev, "maximum frequency is %luHz\n", rt->timer_freq);
+
+	return 0;
+}
+
+static const struct of_device_id rt_timer_match[] = {
+	{ .compatible = "ralink,rt2880-timer" },
+	{},
+};
+
+static struct platform_driver rt_timer_driver = {
+	.probe = rt_timer_probe,
+	.driver = {
+		.name			= "rt-timer",
+		.of_match_table		= rt_timer_match,
+		.suppress_bind_attrs	= true,
+	},
+};
+builtin_platform_driver(rt_timer_driver);
diff --git a/arch/mips/rb532/Makefile b/arch/mips/rb532/Makefile
new file mode 100644
index 000000000..fb4b4bf83
--- /dev/null
+++ b/arch/mips/rb532/Makefile
@@ -0,0 +1,8 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Makefile for the RB532 board specific parts of the kernel
+#
+
+obj-$(CONFIG_SERIAL_8250_CONSOLE) += serial.o
+
+obj-y	 += irq.o time.o setup.o prom.o gpio.o devices.o
diff --git a/arch/mips/rb532/Platform b/arch/mips/rb532/Platform
new file mode 100644
index 000000000..12eaa8790
--- /dev/null
+++ b/arch/mips/rb532/Platform
@@ -0,0 +1,6 @@
+#
+# Routerboard 532
+#
+cflags-$(CONFIG_MIKROTIK_RB532)		+=				\
+		-I$(srctree)/arch/mips/include/asm/mach-rc32434
+load-$(CONFIG_MIKROTIK_RB532)		+= 0xffffffff80101000
diff --git a/arch/mips/rb532/devices.c b/arch/mips/rb532/devices.c
new file mode 100644
index 000000000..b7f6f782d
--- /dev/null
+++ b/arch/mips/rb532/devices.c
@@ -0,0 +1,313 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *  RouterBoard 500 Platform devices
+ *
+ *  Copyright (C) 2006 Felix Fietkau <nbd@openwrt.org>
+ *  Copyright (C) 2007 Florian Fainelli <florian@openwrt.org>
+ */
+#include <linux/kernel.h>
+#include <linux/export.h>
+#include <linux/init.h>
+#include <linux/ctype.h>
+#include <linux/string.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/platnand.h>
+#include <linux/mtd/mtd.h>
+#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
+#include <linux/gpio_keys.h>
+#include <linux/input.h>
+#include <linux/serial_8250.h>
+
+#include <asm/bootinfo.h>
+
+#include <asm/mach-rc32434/rc32434.h>
+#include <asm/mach-rc32434/dma.h>
+#include <asm/mach-rc32434/dma_v.h>
+#include <asm/mach-rc32434/eth.h>
+#include <asm/mach-rc32434/rb.h>
+#include <asm/mach-rc32434/integ.h>
+#include <asm/mach-rc32434/gpio.h>
+#include <asm/mach-rc32434/irq.h>
+
+#define ETH0_RX_DMA_ADDR  (DMA0_BASE_ADDR + 0 * DMA_CHAN_OFFSET)
+#define ETH0_TX_DMA_ADDR  (DMA0_BASE_ADDR + 1 * DMA_CHAN_OFFSET)
+
+extern unsigned int idt_cpu_freq;
+
+static struct mpmc_device dev3;
+
+void set_latch_u5(unsigned char or_mask, unsigned char nand_mask)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&dev3.lock, flags);
+
+	dev3.state = (dev3.state | or_mask) & ~nand_mask;
+	writeb(dev3.state, dev3.base);
+
+	spin_unlock_irqrestore(&dev3.lock, flags);
+}
+EXPORT_SYMBOL(set_latch_u5);
+
+unsigned char get_latch_u5(void)
+{
+	return dev3.state;
+}
+EXPORT_SYMBOL(get_latch_u5);
+
+static struct resource korina_dev0_res[] = {
+	{
+		.name = "emac",
+		.start = ETH0_BASE_ADDR,
+		.end = ETH0_BASE_ADDR + sizeof(struct eth_regs),
+		.flags = IORESOURCE_MEM,
+	 }, {
+		.name = "rx",
+		.start = ETH0_DMA_RX_IRQ,
+		.end = ETH0_DMA_RX_IRQ,
+		.flags = IORESOURCE_IRQ
+	}, {
+		.name = "tx",
+		.start = ETH0_DMA_TX_IRQ,
+		.end = ETH0_DMA_TX_IRQ,
+		.flags = IORESOURCE_IRQ
+	}, {
+		.name = "dma_rx",
+		.start = ETH0_RX_DMA_ADDR,
+		.end = ETH0_RX_DMA_ADDR + DMA_CHAN_OFFSET - 1,
+		.flags = IORESOURCE_MEM,
+	 }, {
+		.name = "dma_tx",
+		.start = ETH0_TX_DMA_ADDR,
+		.end = ETH0_TX_DMA_ADDR + DMA_CHAN_OFFSET - 1,
+		.flags = IORESOURCE_MEM,
+	 }
+};
+
+static struct korina_device korina_dev0_data = {
+	.name = "korina0",
+	.mac = {0xde, 0xca, 0xff, 0xc0, 0xff, 0xee}
+};
+
+static struct platform_device korina_dev0 = {
+	.id = -1,
+	.name = "korina",
+	.resource = korina_dev0_res,
+	.num_resources = ARRAY_SIZE(korina_dev0_res),
+	.dev = {
+		.platform_data = &korina_dev0_data.mac,
+	}
+};
+
+static struct resource cf_slot0_res[] = {
+	{
+		.name = "cf_membase",
+		.flags = IORESOURCE_MEM
+	}, {
+		.name = "cf_irq",
+		.start = (8 + 4 * 32 + CF_GPIO_NUM),	/* 149 */
+		.end = (8 + 4 * 32 + CF_GPIO_NUM),
+		.flags = IORESOURCE_IRQ
+	}
+};
+
+static struct gpiod_lookup_table cf_slot0_gpio_table = {
+	.dev_id = "pata-rb532-cf",
+	.table = {
+		GPIO_LOOKUP("gpio0", CF_GPIO_NUM,
+			    NULL, GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
+static struct platform_device cf_slot0 = {
+	.id = -1,
+	.name = "pata-rb532-cf",
+	.resource = cf_slot0_res,
+	.num_resources = ARRAY_SIZE(cf_slot0_res),
+};
+
+/* Resources and device for NAND */
+static int rb532_dev_ready(struct nand_chip *chip)
+{
+	return gpio_get_value(GPIO_RDY);
+}
+
+static void rb532_cmd_ctrl(struct nand_chip *chip, int cmd, unsigned int ctrl)
+{
+	unsigned char orbits, nandbits;
+
+	if (ctrl & NAND_CTRL_CHANGE) {
+		orbits = (ctrl & NAND_CLE) << 1;
+		orbits |= (ctrl & NAND_ALE) >> 1;
+
+		nandbits = (~ctrl & NAND_CLE) << 1;
+		nandbits |= (~ctrl & NAND_ALE) >> 1;
+
+		set_latch_u5(orbits, nandbits);
+	}
+	if (cmd != NAND_CMD_NONE)
+		writeb(cmd, chip->legacy.IO_ADDR_W);
+}
+
+static struct resource nand_slot0_res[] = {
+	[0] = {
+		.name = "nand_membase",
+		.flags = IORESOURCE_MEM
+	}
+};
+
+static struct platform_nand_data rb532_nand_data = {
+	.ctrl.dev_ready = rb532_dev_ready,
+	.ctrl.cmd_ctrl	= rb532_cmd_ctrl,
+};
+
+static struct platform_device nand_slot0 = {
+	.name = "gen_nand",
+	.id = -1,
+	.resource = nand_slot0_res,
+	.num_resources = ARRAY_SIZE(nand_slot0_res),
+	.dev.platform_data = &rb532_nand_data,
+};
+
+static struct mtd_partition rb532_partition_info[] = {
+	{
+		.name = "Routerboard NAND boot",
+		.offset = 0,
+		.size = 4 * 1024 * 1024,
+	}, {
+		.name = "rootfs",
+		.offset = MTDPART_OFS_NXTBLK,
+		.size = MTDPART_SIZ_FULL,
+	}
+};
+
+static struct platform_device rb532_led = {
+	.name = "rb532-led",
+	.id = -1,
+};
+
+static struct platform_device rb532_button = {
+	.name	= "rb532-button",
+	.id	= -1,
+};
+
+static struct resource rb532_wdt_res[] = {
+	{
+		.name = "rb532_wdt_res",
+		.start = INTEG0_BASE_ADDR,
+		.end = INTEG0_BASE_ADDR + sizeof(struct integ),
+		.flags = IORESOURCE_MEM,
+	}
+};
+
+static struct platform_device rb532_wdt = {
+	.name		= "rc32434_wdt",
+	.id		= -1,
+	.resource	= rb532_wdt_res,
+	.num_resources	= ARRAY_SIZE(rb532_wdt_res),
+};
+
+static struct plat_serial8250_port rb532_uart_res[] = {
+	{
+		.type           = PORT_16550A,
+		.membase	= (char *)KSEG1ADDR(REGBASE + UART0BASE),
+		.irq		= UART0_IRQ,
+		.regshift	= 2,
+		.iotype		= UPIO_MEM,
+		.flags		= UPF_BOOT_AUTOCONF,
+	},
+	{
+		.flags		= 0,
+	}
+};
+
+static struct platform_device rb532_uart = {
+	.name		   = "serial8250",
+	.id		   = PLAT8250_DEV_PLATFORM,
+	.dev.platform_data = &rb532_uart_res,
+};
+
+static struct platform_device *rb532_devs[] = {
+	&korina_dev0,
+	&nand_slot0,
+	&cf_slot0,
+	&rb532_led,
+	&rb532_button,
+	&rb532_uart,
+	&rb532_wdt
+};
+
+/* NAND definitions */
+#define NAND_CHIP_DELAY 25
+
+static void __init rb532_nand_setup(void)
+{
+	switch (mips_machtype) {
+	case MACH_MIKROTIK_RB532A:
+		set_latch_u5(LO_FOFF | LO_CEX,
+				LO_ULED | LO_ALE | LO_CLE | LO_WPX);
+		break;
+	default:
+		set_latch_u5(LO_WPX | LO_FOFF | LO_CEX,
+				LO_ULED | LO_ALE | LO_CLE);
+		break;
+	}
+
+	/* Setup NAND specific settings */
+	rb532_nand_data.chip.nr_chips = 1;
+	rb532_nand_data.chip.nr_partitions = ARRAY_SIZE(rb532_partition_info);
+	rb532_nand_data.chip.partitions = rb532_partition_info;
+	rb532_nand_data.chip.chip_delay = NAND_CHIP_DELAY;
+}
+
+
+static int __init plat_setup_devices(void)
+{
+	/* Look for the CF card reader */
+	if (!readl(IDT434_REG_BASE + DEV1MASK))
+		rb532_devs[2] = NULL;	/* disable cf_slot0 at index 2 */
+	else {
+		cf_slot0_res[0].start =
+		    readl(IDT434_REG_BASE + DEV1BASE);
+		cf_slot0_res[0].end = cf_slot0_res[0].start + 0x1000;
+	}
+
+	/* Read the NAND resources from the device controller */
+	nand_slot0_res[0].start = readl(IDT434_REG_BASE + DEV2BASE);
+	nand_slot0_res[0].end = nand_slot0_res[0].start + 0x1000;
+
+	/* Read and map device controller 3 */
+	dev3.base = ioremap(readl(IDT434_REG_BASE + DEV3BASE), 1);
+
+	if (!dev3.base) {
+		printk(KERN_ERR "rb532: cannot remap device controller 3\n");
+		return -ENXIO;
+	}
+
+	/* Initialise the NAND device */
+	rb532_nand_setup();
+
+	/* set the uart clock to the current cpu frequency */
+	rb532_uart_res[0].uartclk = idt_cpu_freq;
+
+	gpiod_add_lookup_table(&cf_slot0_gpio_table);
+	return platform_add_devices(rb532_devs, ARRAY_SIZE(rb532_devs));
+}
+
+#ifdef CONFIG_NET
+
+static int __init setup_kmac(char *s)
+{
+	printk(KERN_INFO "korina mac = %s\n", s);
+	if (!mac_pton(s, korina_dev0_data.mac))
+		printk(KERN_ERR "Invalid mac\n");
+	return 1;
+}
+
+__setup("kmac=", setup_kmac);
+
+#endif /* CONFIG_NET */
+
+arch_initcall(plat_setup_devices);
diff --git a/arch/mips/rb532/gpio.c b/arch/mips/rb532/gpio.c
new file mode 100644
index 000000000..29c21b9d4
--- /dev/null
+++ b/arch/mips/rb532/gpio.c
@@ -0,0 +1,217 @@
+/*
+ *  Miscellaneous functions for IDT EB434 board
+ *
+ *  Copyright 2004 IDT Inc. (rischelp@idt.com)
+ *  Copyright 2006 Phil Sutter <n0-1@freewrt.org>
+ *  Copyright 2007 Florian Fainelli <florian@openwrt.org>
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/export.h>
+#include <linux/spinlock.h>
+#include <linux/platform_device.h>
+#include <linux/gpio/driver.h>
+
+#include <asm/mach-rc32434/rb.h>
+#include <asm/mach-rc32434/gpio.h>
+
+#define GPIOBASE	0x050000
+/* Offsets relative to GPIOBASE */
+#define GPIOFUNC	0x00
+#define GPIOCFG		0x04
+#define GPIOD		0x08
+#define GPIOILEVEL	0x0C
+#define GPIOISTAT	0x10
+#define GPIONMIEN	0x14
+#define IMASK6		0x38
+
+struct rb532_gpio_chip {
+	struct gpio_chip chip;
+	void __iomem	 *regbase;
+};
+
+static struct resource rb532_gpio_reg0_res[] = {
+	{
+		.name	= "gpio_reg0",
+		.start	= REGBASE + GPIOBASE,
+		.end	= REGBASE + GPIOBASE + sizeof(struct rb532_gpio_reg) - 1,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
+/* rb532_set_bit - sanely set a bit
+ *
+ * bitval: new value for the bit
+ * offset: bit index in the 4 byte address range
+ * ioaddr: 4 byte aligned address being altered
+ */
+static inline void rb532_set_bit(unsigned bitval,
+		unsigned offset, void __iomem *ioaddr)
+{
+	unsigned long flags;
+	u32 val;
+
+	local_irq_save(flags);
+
+	val = readl(ioaddr);
+	val &= ~(!bitval << offset);   /* unset bit if bitval == 0 */
+	val |= (!!bitval << offset);   /* set bit if bitval == 1 */
+	writel(val, ioaddr);
+
+	local_irq_restore(flags);
+}
+
+/* rb532_get_bit - read a bit
+ *
+ * returns the boolean state of the bit, which may be > 1
+ */
+static inline int rb532_get_bit(unsigned offset, void __iomem *ioaddr)
+{
+	return readl(ioaddr) & (1 << offset);
+}
+
+/*
+ * Return GPIO level */
+static int rb532_gpio_get(struct gpio_chip *chip, unsigned offset)
+{
+	struct rb532_gpio_chip	*gpch;
+
+	gpch = gpiochip_get_data(chip);
+	return !!rb532_get_bit(offset, gpch->regbase + GPIOD);
+}
+
+/*
+ * Set output GPIO level
+ */
+static void rb532_gpio_set(struct gpio_chip *chip,
+				unsigned offset, int value)
+{
+	struct rb532_gpio_chip	*gpch;
+
+	gpch = gpiochip_get_data(chip);
+	rb532_set_bit(value, offset, gpch->regbase + GPIOD);
+}
+
+/*
+ * Set GPIO direction to input
+ */
+static int rb532_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
+{
+	struct rb532_gpio_chip	*gpch;
+
+	gpch = gpiochip_get_data(chip);
+
+	/* disable alternate function in case it's set */
+	rb532_set_bit(0, offset, gpch->regbase + GPIOFUNC);
+
+	rb532_set_bit(0, offset, gpch->regbase + GPIOCFG);
+	return 0;
+}
+
+/*
+ * Set GPIO direction to output
+ */
+static int rb532_gpio_direction_output(struct gpio_chip *chip,
+					unsigned offset, int value)
+{
+	struct rb532_gpio_chip	*gpch;
+
+	gpch = gpiochip_get_data(chip);
+
+	/* disable alternate function in case it's set */
+	rb532_set_bit(0, offset, gpch->regbase + GPIOFUNC);
+
+	/* set the initial output value */
+	rb532_set_bit(value, offset, gpch->regbase + GPIOD);
+
+	rb532_set_bit(1, offset, gpch->regbase + GPIOCFG);
+	return 0;
+}
+
+static int rb532_gpio_to_irq(struct gpio_chip *chip, unsigned gpio)
+{
+	return 8 + 4 * 32 + gpio;
+}
+
+static struct rb532_gpio_chip rb532_gpio_chip[] = {
+	[0] = {
+		.chip = {
+			.label			= "gpio0",
+			.direction_input	= rb532_gpio_direction_input,
+			.direction_output	= rb532_gpio_direction_output,
+			.get			= rb532_gpio_get,
+			.set			= rb532_gpio_set,
+			.to_irq			= rb532_gpio_to_irq,
+			.base			= 0,
+			.ngpio			= 32,
+		},
+	},
+};
+
+/*
+ * Set GPIO interrupt level
+ */
+void rb532_gpio_set_ilevel(int bit, unsigned gpio)
+{
+	rb532_set_bit(bit, gpio, rb532_gpio_chip->regbase + GPIOILEVEL);
+}
+EXPORT_SYMBOL(rb532_gpio_set_ilevel);
+
+/*
+ * Set GPIO interrupt status
+ */
+void rb532_gpio_set_istat(int bit, unsigned gpio)
+{
+	rb532_set_bit(bit, gpio, rb532_gpio_chip->regbase + GPIOISTAT);
+}
+EXPORT_SYMBOL(rb532_gpio_set_istat);
+
+/*
+ * Configure GPIO alternate function
+ */
+void rb532_gpio_set_func(unsigned gpio)
+{
+       rb532_set_bit(1, gpio, rb532_gpio_chip->regbase + GPIOFUNC);
+}
+EXPORT_SYMBOL(rb532_gpio_set_func);
+
+int __init rb532_gpio_init(void)
+{
+	struct resource *r;
+
+	r = rb532_gpio_reg0_res;
+	rb532_gpio_chip->regbase = ioremap(r->start, resource_size(r));
+
+	if (!rb532_gpio_chip->regbase) {
+		printk(KERN_ERR "rb532: cannot remap GPIO register 0\n");
+		return -ENXIO;
+	}
+
+	/* Register our GPIO chip */
+	gpiochip_add_data(&rb532_gpio_chip->chip, rb532_gpio_chip);
+
+	return 0;
+}
+arch_initcall(rb532_gpio_init);
diff --git a/arch/mips/rb532/irq.c b/arch/mips/rb532/irq.c
new file mode 100644
index 000000000..25cc250f2
--- /dev/null
+++ b/arch/mips/rb532/irq.c
@@ -0,0 +1,234 @@
+/*
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ * Copyright 2002 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc.
+ *		stevel@mvista.com or source@mvista.com
+ */
+
+#include <linux/bitops.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/kernel_stat.h>
+#include <linux/signal.h>
+#include <linux/sched.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/timex.h>
+#include <linux/random.h>
+#include <linux/delay.h>
+
+#include <asm/bootinfo.h>
+#include <asm/time.h>
+#include <asm/mipsregs.h>
+
+#include <asm/mach-rc32434/irq.h>
+#include <asm/mach-rc32434/gpio.h>
+
+struct intr_group {
+	u32 mask;	/* mask of valid bits in pending/mask registers */
+	volatile u32 *base_addr;
+};
+
+#define RC32434_NR_IRQS	 (GROUP4_IRQ_BASE + 32)
+
+#if (NR_IRQS < RC32434_NR_IRQS)
+#error Too little irqs defined. Did you override <asm/irq.h> ?
+#endif
+
+static const struct intr_group intr_group[NUM_INTR_GROUPS] = {
+	{
+		.mask	= 0x0000efff,
+		.base_addr = (u32 *) KSEG1ADDR(IC_GROUP0_PEND + 0 * IC_GROUP_OFFSET)},
+	{
+		.mask	= 0x00001fff,
+		.base_addr = (u32 *) KSEG1ADDR(IC_GROUP0_PEND + 1 * IC_GROUP_OFFSET)},
+	{
+		.mask	= 0x00000007,
+		.base_addr = (u32 *) KSEG1ADDR(IC_GROUP0_PEND + 2 * IC_GROUP_OFFSET)},
+	{
+		.mask	= 0x0003ffff,
+		.base_addr = (u32 *) KSEG1ADDR(IC_GROUP0_PEND + 3 * IC_GROUP_OFFSET)},
+	{
+		.mask	= 0xffffffff,
+		.base_addr = (u32 *) KSEG1ADDR(IC_GROUP0_PEND + 4 * IC_GROUP_OFFSET)}
+};
+
+#define READ_PEND(base) (*(base))
+#define READ_MASK(base) (*(base + 2))
+#define WRITE_MASK(base, val) (*(base + 2) = (val))
+
+static inline int irq_to_group(unsigned int irq_nr)
+{
+	return (irq_nr - GROUP0_IRQ_BASE) >> 5;
+}
+
+static inline int group_to_ip(unsigned int group)
+{
+	return group + 2;
+}
+
+static inline void enable_local_irq(unsigned int ip)
+{
+	int ipnum = 0x100 << ip;
+
+	set_c0_status(ipnum);
+}
+
+static inline void disable_local_irq(unsigned int ip)
+{
+	int ipnum = 0x100 << ip;
+
+	clear_c0_status(ipnum);
+}
+
+static inline void ack_local_irq(unsigned int ip)
+{
+	int ipnum = 0x100 << ip;
+
+	clear_c0_cause(ipnum);
+}
+
+static void rb532_enable_irq(struct irq_data *d)
+{
+	unsigned int group, intr_bit, irq_nr = d->irq;
+	int ip = irq_nr - GROUP0_IRQ_BASE;
+	volatile unsigned int *addr;
+
+	if (ip < 0)
+		enable_local_irq(irq_nr);
+	else {
+		group = ip >> 5;
+
+		ip &= (1 << 5) - 1;
+		intr_bit = 1 << ip;
+
+		enable_local_irq(group_to_ip(group));
+
+		addr = intr_group[group].base_addr;
+		WRITE_MASK(addr, READ_MASK(addr) & ~intr_bit);
+	}
+}
+
+static void rb532_disable_irq(struct irq_data *d)
+{
+	unsigned int group, intr_bit, mask, irq_nr = d->irq;
+	int ip = irq_nr - GROUP0_IRQ_BASE;
+	volatile unsigned int *addr;
+
+	if (ip < 0) {
+		disable_local_irq(irq_nr);
+	} else {
+		group = ip >> 5;
+
+		ip &= (1 << 5) - 1;
+		intr_bit = 1 << ip;
+		addr = intr_group[group].base_addr;
+		mask = READ_MASK(addr);
+		mask |= intr_bit;
+		WRITE_MASK(addr, mask);
+
+		/* There is a maximum of 14 GPIO interrupts */
+		if (group == GPIO_MAPPED_IRQ_GROUP && irq_nr <= (GROUP4_IRQ_BASE + 13))
+			rb532_gpio_set_istat(0, irq_nr - GPIO_MAPPED_IRQ_BASE);
+
+		/*
+		 * if there are no more interrupts enabled in this
+		 * group, disable corresponding IP
+		 */
+		if (mask == intr_group[group].mask)
+			disable_local_irq(group_to_ip(group));
+	}
+}
+
+static void rb532_mask_and_ack_irq(struct irq_data *d)
+{
+	rb532_disable_irq(d);
+	ack_local_irq(group_to_ip(irq_to_group(d->irq)));
+}
+
+static int rb532_set_type(struct irq_data *d,  unsigned type)
+{
+	int gpio = d->irq - GPIO_MAPPED_IRQ_BASE;
+	int group = irq_to_group(d->irq);
+
+	if (group != GPIO_MAPPED_IRQ_GROUP || d->irq > (GROUP4_IRQ_BASE + 13))
+		return (type == IRQ_TYPE_LEVEL_HIGH) ? 0 : -EINVAL;
+
+	switch (type) {
+	case IRQ_TYPE_LEVEL_HIGH:
+		rb532_gpio_set_ilevel(1, gpio);
+		break;
+	case IRQ_TYPE_LEVEL_LOW:
+		rb532_gpio_set_ilevel(0, gpio);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static struct irq_chip rc32434_irq_type = {
+	.name		= "RB532",
+	.irq_ack	= rb532_disable_irq,
+	.irq_mask	= rb532_disable_irq,
+	.irq_mask_ack	= rb532_mask_and_ack_irq,
+	.irq_unmask	= rb532_enable_irq,
+	.irq_set_type	= rb532_set_type,
+};
+
+void __init arch_init_irq(void)
+{
+	int i;
+
+	pr_info("Initializing IRQ's: %d out of %d\n", RC32434_NR_IRQS, NR_IRQS);
+
+	for (i = 0; i < RC32434_NR_IRQS; i++)
+		irq_set_chip_and_handler(i, &rc32434_irq_type,
+					 handle_level_irq);
+}
+
+/* Main Interrupt dispatcher */
+asmlinkage void plat_irq_dispatch(void)
+{
+	unsigned int ip, pend, group;
+	volatile unsigned int *addr;
+	unsigned int cp0_cause = read_c0_cause() & read_c0_status();
+
+	if (cp0_cause & CAUSEF_IP7) {
+		do_IRQ(7);
+	} else {
+		ip = (cp0_cause & 0x7c00);
+		if (ip) {
+			group = 21 + (fls(ip) - 32);
+
+			addr = intr_group[group].base_addr;
+
+			pend = READ_PEND(addr);
+			pend &= ~READ_MASK(addr);	/* only unmasked interrupts */
+			pend = 39 + (fls(pend) - 32);
+			do_IRQ((group << 5) + pend);
+		}
+	}
+}
diff --git a/arch/mips/rb532/prom.c b/arch/mips/rb532/prom.c
new file mode 100644
index 000000000..b11693715
--- /dev/null
+++ b/arch/mips/rb532/prom.c
@@ -0,0 +1,124 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *  RouterBoard 500 specific prom routines
+ *
+ *  Copyright (C) 2003, Peter Sadik <peter.sadik@idt.com>
+ *  Copyright (C) 2005-2006, P.Christeas <p_christ@hol.gr>
+ *  Copyright (C) 2007, Gabor Juhos <juhosg@openwrt.org>
+ *			Felix Fietkau <nbd@openwrt.org>
+ *			Florian Fainelli <florian@openwrt.org>
+ */
+
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/export.h>
+#include <linux/string.h>
+#include <linux/console.h>
+#include <linux/memblock.h>
+#include <linux/ioport.h>
+
+#include <asm/bootinfo.h>
+#include <asm/mach-rc32434/ddr.h>
+#include <asm/mach-rc32434/prom.h>
+
+unsigned int idt_cpu_freq = 132000000;
+EXPORT_SYMBOL(idt_cpu_freq);
+
+static struct resource ddr_reg[] = {
+	{
+		.name = "ddr-reg",
+		.start = DDR0_PHYS_ADDR,
+		.end = DDR0_PHYS_ADDR + sizeof(struct ddr_ram),
+		.flags = IORESOURCE_MEM,
+	}
+};
+
+static inline int match_tag(char *arg, const char *tag)
+{
+	return strncmp(arg, tag, strlen(tag)) == 0;
+}
+
+static inline unsigned long tag2ul(char *arg, const char *tag)
+{
+	char *num;
+
+	num = arg + strlen(tag);
+	return simple_strtoul(num, 0, 10);
+}
+
+void __init prom_setup_cmdline(void)
+{
+	static char cmd_line[COMMAND_LINE_SIZE] __initdata;
+	char *cp, *board;
+	int prom_argc;
+	char **prom_argv;
+	int i;
+
+	prom_argc = fw_arg0;
+	prom_argv = (char **) fw_arg1;
+
+	cp = cmd_line;
+		/* Note: it is common that parameters start
+		 * at argv[1] and not argv[0],
+		 * however, our elf loader starts at [0] */
+	for (i = 0; i < prom_argc; i++) {
+		if (match_tag(prom_argv[i], FREQ_TAG)) {
+			idt_cpu_freq = tag2ul(prom_argv[i], FREQ_TAG);
+			continue;
+		}
+#ifdef IGNORE_CMDLINE_MEM
+		/* parses out the "mem=xx" arg */
+		if (match_tag(prom_argv[i], MEM_TAG))
+			continue;
+#endif
+		if (i > 0)
+			*(cp++) = ' ';
+		if (match_tag(prom_argv[i], BOARD_TAG)) {
+			board = prom_argv[i] + strlen(BOARD_TAG);
+
+			if (match_tag(board, BOARD_RB532A))
+				mips_machtype = MACH_MIKROTIK_RB532A;
+			else
+				mips_machtype = MACH_MIKROTIK_RB532;
+		}
+
+		strcpy(cp, prom_argv[i]);
+		cp += strlen(prom_argv[i]);
+	}
+	*(cp++) = ' ';
+
+	i = strlen(arcs_cmdline);
+	if (i > 0) {
+		*(cp++) = ' ';
+		strcpy(cp, arcs_cmdline);
+		cp += strlen(arcs_cmdline);
+	}
+	cmd_line[COMMAND_LINE_SIZE - 1] = '\0';
+
+	strcpy(arcs_cmdline, cmd_line);
+}
+
+void __init prom_init(void)
+{
+	struct ddr_ram __iomem *ddr;
+	phys_addr_t memsize;
+	phys_addr_t ddrbase;
+
+	ddr = ioremap(ddr_reg[0].start,
+			ddr_reg[0].end - ddr_reg[0].start);
+
+	if (!ddr) {
+		printk(KERN_ERR "Unable to remap DDR register\n");
+		return;
+	}
+
+	ddrbase = (phys_addr_t)&ddr->ddrbase;
+	memsize = (phys_addr_t)&ddr->ddrmask;
+	memsize = 0 - memsize;
+
+	prom_setup_cmdline();
+
+	/* give all RAM to boot allocator,
+	 * except for the first 0x400 and the last 0x200 bytes */
+	memblock_add(ddrbase + 0x400, memsize - 0x600);
+}
diff --git a/arch/mips/rb532/serial.c b/arch/mips/rb532/serial.c
new file mode 100644
index 000000000..70482540b
--- /dev/null
+++ b/arch/mips/rb532/serial.c
@@ -0,0 +1,54 @@
+/*
+ *  BRIEF MODULE DESCRIPTION
+ *     Serial port initialisation.
+ *
+ *  Copyright 2004 IDT Inc. (rischelp@idt.com)
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/init.h>
+#include <linux/tty.h>
+#include <linux/serial_core.h>
+#include <linux/serial_8250.h>
+#include <linux/irq.h>
+
+#include <asm/serial.h>
+#include <asm/mach-rc32434/rb.h>
+
+extern unsigned int idt_cpu_freq;
+
+static struct uart_port rb532_uart = {
+	.flags = UPF_BOOT_AUTOCONF,
+	.line = 0,
+	.irq = UART0_IRQ,
+	.iotype = UPIO_MEM,
+	.membase = (char *)KSEG1ADDR(REGBASE + UART0BASE),
+	.regshift = 2
+};
+
+int __init setup_serial_port(void)
+{
+	rb532_uart.uartclk = idt_cpu_freq;
+
+	return early_serial_setup(&rb532_uart);
+}
+arch_initcall(setup_serial_port);
diff --git a/arch/mips/rb532/setup.c b/arch/mips/rb532/setup.c
new file mode 100644
index 000000000..51af9d374
--- /dev/null
+++ b/arch/mips/rb532/setup.c
@@ -0,0 +1,81 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * setup.c - boot time setup code
+ */
+
+#include <linux/init.h>
+#include <linux/export.h>
+
+#include <asm/bootinfo.h>
+#include <asm/reboot.h>
+#include <asm/time.h>
+#include <linux/ioport.h>
+
+#include <asm/mach-rc32434/rb.h>
+#include <asm/mach-rc32434/pci.h>
+
+struct pci_reg __iomem *pci_reg;
+EXPORT_SYMBOL(pci_reg);
+
+static struct resource pci0_res[] = {
+	{
+		.name = "pci_reg0",
+		.start = PCI0_BASE_ADDR,
+		.end = PCI0_BASE_ADDR + sizeof(struct pci_reg),
+		.flags = IORESOURCE_MEM,
+	}
+};
+
+static void rb_machine_restart(char *command)
+{
+	/* just jump to the reset vector */
+	writel(0x80000001, IDT434_REG_BASE + RST);
+	((void (*)(void)) KSEG1ADDR(0x1FC00000u))();
+}
+
+static void rb_machine_halt(void)
+{
+	for (;;)
+		continue;
+}
+
+void __init plat_mem_setup(void)
+{
+	u32 val;
+
+	_machine_restart = rb_machine_restart;
+	_machine_halt = rb_machine_halt;
+	pm_power_off = rb_machine_halt;
+
+	set_io_port_base(KSEG1);
+
+	pci_reg = ioremap(pci0_res[0].start,
+				pci0_res[0].end - pci0_res[0].start);
+	if (!pci_reg) {
+		printk(KERN_ERR "Could not remap PCI registers\n");
+		return;
+	}
+
+	val = __raw_readl(&pci_reg->pcic);
+	val &= 0xFFFFFF7;
+	__raw_writel(val, (void *)&pci_reg->pcic);
+
+#ifdef CONFIG_PCI
+	/* Enable PCI interrupts in EPLD Mask register */
+	*epld_mask = 0x0;
+	*(epld_mask + 1) = 0x0;
+#endif
+	write_c0_wired(0);
+}
+
+const char *get_system_type(void)
+{
+	switch (mips_machtype) {
+	case MACH_MIKROTIK_RB532A:
+		return "Mikrotik RB532A";
+		break;
+	default:
+		return "Mikrotik RB532";
+		break;
+	}
+}
diff --git a/arch/mips/rb532/time.c b/arch/mips/rb532/time.c
new file mode 100644
index 000000000..68713dd32
--- /dev/null
+++ b/arch/mips/rb532/time.c
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 1999,2000 MIPS Technologies, Inc.  All rights reserved.
+ *
+ *  Setting up the clock on the MIPS boards.
+ */
+
+#include <linux/init.h>
+#include <linux/kernel_stat.h>
+#include <linux/ptrace.h>
+#include <linux/sched.h>
+#include <linux/spinlock.h>
+#include <linux/mc146818rtc.h>
+#include <linux/irq.h>
+#include <linux/timex.h>
+
+#include <asm/mipsregs.h>
+#include <asm/time.h>
+#include <asm/mach-rc32434/rc32434.h>
+
+extern unsigned int idt_cpu_freq;
+
+/*
+ * Figure out the r4k offset, the amount to increment the compare
+ * register for each time tick. There is no RTC available.
+ *
+ * The RC32434 counts at half the CPU *core* speed.
+ */
+static unsigned long __init cal_r4koff(void)
+{
+	mips_hpt_frequency = idt_cpu_freq * IDT_CLOCK_MULT / 2;
+
+	return mips_hpt_frequency / HZ;
+}
+
+void __init plat_time_init(void)
+{
+	unsigned int est_freq;
+	unsigned long flags, r4k_offset;
+
+	local_irq_save(flags);
+
+	printk(KERN_INFO "calculating r4koff... ");
+	r4k_offset = cal_r4koff();
+	printk("%08lx(%d)\n", r4k_offset, (int) r4k_offset);
+
+	est_freq = 2 * r4k_offset * HZ;
+	est_freq += 5000;	/* round */
+	est_freq -= est_freq % 10000;
+	printk(KERN_INFO "CPU frequency %d.%02d MHz\n", est_freq / 1000000,
+	       (est_freq % 1000000) * 100 / 1000000);
+	local_irq_restore(flags);
+}
diff --git a/arch/mips/sgi-ip22/Makefile b/arch/mips/sgi-ip22/Makefile
new file mode 100644
index 000000000..45f42fa08
--- /dev/null
+++ b/arch/mips/sgi-ip22/Makefile
@@ -0,0 +1,12 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Makefile for the SGI specific kernel interface routines
+# under Linux.
+#
+
+obj-y	+= ip22-mc.o ip22-hpc.o ip22-int.o ip22-time.o ip22-nvram.o \
+	   ip22-platform.o ip22-reset.o ip22-setup.o ip22-gio.o
+
+obj-$(CONFIG_SGI_IP22) += ip22-berr.o
+obj-$(CONFIG_SGI_IP28) += ip28-berr.o
+obj-$(CONFIG_EISA)	+= ip22-eisa.o
diff --git a/arch/mips/sgi-ip22/Platform b/arch/mips/sgi-ip22/Platform
new file mode 100644
index 000000000..a4c46e335
--- /dev/null
+++ b/arch/mips/sgi-ip22/Platform
@@ -0,0 +1,27 @@
+#
+# SGI IP22 (Indy/Indigo2)
+#
+# Set the load address to >= 0xffffffff88069000 if you want to leave space for
+# symmon, 0xffffffff80002000 for production kernels.  Note that the value must
+# be aligned to a multiple of the kernel stack size or the handling of the
+# current variable will break so for 64-bit kernels we have to raise the start
+# address by 8kb.
+#
+cflags-$(CONFIG_SGI_IP22)	+= -I$(srctree)/arch/mips/include/asm/mach-ip22
+ifdef CONFIG_32BIT
+load-$(CONFIG_SGI_IP22)		+= 0xffffffff88002000
+endif
+ifdef CONFIG_64BIT
+load-$(CONFIG_SGI_IP22)		+= 0xffffffff88004000
+endif
+
+#
+# SGI IP28 (Indigo2 R10k)
+#
+# Set the load address to >= 0xa800000020080000 if you want to leave space for
+# symmon, 0xa800000020004000 for production kernels ?  Note that the value must
+# be 16kb aligned or the handling of the current variable will break.
+# Simplified: what IP22 does at 128MB+ in ksegN, IP28 does at 512MB+ in xkphys
+#
+cflags-$(CONFIG_SGI_IP28)	+= -mr10k-cache-barrier=store -I$(srctree)/arch/mips/include/asm/mach-ip28
+load-$(CONFIG_SGI_IP28)		+= 0xa800000020004000
diff --git a/arch/mips/sgi-ip22/ip22-berr.c b/arch/mips/sgi-ip22/ip22-berr.c
new file mode 100644
index 000000000..afe8a6107
--- /dev/null
+++ b/arch/mips/sgi-ip22/ip22-berr.c
@@ -0,0 +1,116 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ip22-berr.c: Bus error handling.
+ *
+ * Copyright (C) 2002, 2003 Ladislav Michl (ladis@linux-mips.org)
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/sched/signal.h>
+
+#include <asm/addrspace.h>
+#include <asm/traps.h>
+#include <asm/branch.h>
+#include <asm/irq_regs.h>
+#include <asm/sgi/mc.h>
+#include <asm/sgi/hpc3.h>
+#include <asm/sgi/ioc.h>
+#include <asm/sgi/ip22.h>
+
+
+static unsigned int cpu_err_stat;	/* Status reg for CPU */
+static unsigned int gio_err_stat;	/* Status reg for GIO */
+static unsigned int cpu_err_addr;	/* Error address reg for CPU */
+static unsigned int gio_err_addr;	/* Error address reg for GIO */
+static unsigned int extio_stat;
+static unsigned int hpc3_berr_stat;	/* Bus error interrupt status */
+
+static void save_and_clear_buserr(void)
+{
+	/* save status registers */
+	cpu_err_addr = sgimc->cerr;
+	cpu_err_stat = sgimc->cstat;
+	gio_err_addr = sgimc->gerr;
+	gio_err_stat = sgimc->gstat;
+	extio_stat = ip22_is_fullhouse() ? sgioc->extio : (sgint->errstat << 4);
+	hpc3_berr_stat = hpc3c0->bestat;
+
+	sgimc->cstat = sgimc->gstat = 0;
+}
+
+#define GIO_ERRMASK	0xff00
+#define CPU_ERRMASK	0x3f00
+
+static void print_buserr(void)
+{
+	if (extio_stat & EXTIO_MC_BUSERR)
+		printk(KERN_ERR "MC Bus Error\n");
+	if (extio_stat & EXTIO_HPC3_BUSERR)
+		printk(KERN_ERR "HPC3 Bus Error 0x%x:<id=0x%x,%s,lane=0x%x>\n",
+			hpc3_berr_stat,
+			(hpc3_berr_stat & HPC3_BESTAT_PIDMASK) >>
+					  HPC3_BESTAT_PIDSHIFT,
+			(hpc3_berr_stat & HPC3_BESTAT_CTYPE) ? "PIO" : "DMA",
+			hpc3_berr_stat & HPC3_BESTAT_BLMASK);
+	if (extio_stat & EXTIO_EISA_BUSERR)
+		printk(KERN_ERR "EISA Bus Error\n");
+	if (cpu_err_stat & CPU_ERRMASK)
+		printk(KERN_ERR "CPU error 0x%x<%s%s%s%s%s%s> @ 0x%08x\n",
+			cpu_err_stat,
+			cpu_err_stat & SGIMC_CSTAT_RD ? "RD " : "",
+			cpu_err_stat & SGIMC_CSTAT_PAR ? "PAR " : "",
+			cpu_err_stat & SGIMC_CSTAT_ADDR ? "ADDR " : "",
+			cpu_err_stat & SGIMC_CSTAT_SYSAD_PAR ? "SYSAD " : "",
+			cpu_err_stat & SGIMC_CSTAT_SYSCMD_PAR ? "SYSCMD " : "",
+			cpu_err_stat & SGIMC_CSTAT_BAD_DATA ? "BAD_DATA " : "",
+			cpu_err_addr);
+	if (gio_err_stat & GIO_ERRMASK)
+		printk(KERN_ERR "GIO error 0x%x:<%s%s%s%s%s%s%s%s> @ 0x%08x\n",
+			gio_err_stat,
+			gio_err_stat & SGIMC_GSTAT_RD ? "RD " : "",
+			gio_err_stat & SGIMC_GSTAT_WR ? "WR " : "",
+			gio_err_stat & SGIMC_GSTAT_TIME ? "TIME " : "",
+			gio_err_stat & SGIMC_GSTAT_PROM ? "PROM " : "",
+			gio_err_stat & SGIMC_GSTAT_ADDR ? "ADDR " : "",
+			gio_err_stat & SGIMC_GSTAT_BC ? "BC " : "",
+			gio_err_stat & SGIMC_GSTAT_PIO_RD ? "PIO_RD " : "",
+			gio_err_stat & SGIMC_GSTAT_PIO_WR ? "PIO_WR " : "",
+			gio_err_addr);
+}
+
+/*
+ * MC sends an interrupt whenever bus or parity errors occur. In addition,
+ * if the error happened during a CPU read, it also asserts the bus error
+ * pin on the R4K. Code in bus error handler save the MC bus error registers
+ * and then clear the interrupt when this happens.
+ */
+
+void ip22_be_interrupt(int irq)
+{
+	const int field = 2 * sizeof(unsigned long);
+	struct pt_regs *regs = get_irq_regs();
+
+	save_and_clear_buserr();
+	print_buserr();
+	printk(KERN_ALERT "%s bus error, epc == %0*lx, ra == %0*lx\n",
+	       (regs->cp0_cause & 4) ? "Data" : "Instruction",
+	       field, regs->cp0_epc, field, regs->regs[31]);
+	/* Assume it would be too dangerous to continue ... */
+	die_if_kernel("Oops", regs);
+	force_sig(SIGBUS);
+}
+
+static int ip22_be_handler(struct pt_regs *regs, int is_fixup)
+{
+	save_and_clear_buserr();
+	if (is_fixup)
+		return MIPS_BE_FIXUP;
+	print_buserr();
+	return MIPS_BE_FATAL;
+}
+
+void __init ip22_be_init(void)
+{
+	mips_set_be_handler(ip22_be_handler);
+}
diff --git a/arch/mips/sgi-ip22/ip22-eisa.c b/arch/mips/sgi-ip22/ip22-eisa.c
new file mode 100644
index 000000000..f3b0e90e0
--- /dev/null
+++ b/arch/mips/sgi-ip22/ip22-eisa.c
@@ -0,0 +1,139 @@
+/*
+ * Basic EISA bus support for the SGI Indigo-2.
+ *
+ * (C) 2002 Pascal Dameme <netinet@freesurf.fr>
+ *	and Marc Zyngier <mzyngier@freesurf.fr>
+ *
+ * This code is released under both the GPL version 2 and BSD
+ * licenses.  Either license may be used.
+ *
+ * This code offers a very basic support for this EISA bus present in
+ * the SGI Indigo-2. It currently only supports PIO (forget about DMA
+ * for the time being). This is enough for a low-end ethernet card,
+ * but forget about your favorite SCSI card...
+ *
+ * TODO :
+ * - Fix bugs...
+ * - Add ISA support
+ * - Add DMA (yeah, right...).
+ * - Fix more bugs.
+ */
+
+#include <linux/eisa.h>
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <linux/kernel_stat.h>
+#include <linux/signal.h>
+#include <linux/sched.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/mipsregs.h>
+#include <asm/addrspace.h>
+#include <asm/processor.h>
+#include <asm/sgi/ioc.h>
+#include <asm/sgi/mc.h>
+#include <asm/sgi/ip22.h>
+#include <asm/i8259.h>
+
+/* I2 has four EISA slots. */
+#define IP22_EISA_MAX_SLOTS	  4
+#define EISA_MAX_IRQ		 16
+
+#define EIU_MODE_REG	 0x0001ffc0
+#define EIU_STAT_REG	 0x0001ffc4
+#define EIU_PREMPT_REG	 0x0001ffc8
+#define EIU_QUIET_REG	 0x0001ffcc
+#define EIU_INTRPT_ACK	 0x00010004
+
+static char __init *decode_eisa_sig(unsigned long addr)
+{
+	static char sig_str[EISA_SIG_LEN] __initdata;
+	u8 sig[4];
+	u16 rev;
+	int i;
+
+	for (i = 0; i < 4; i++) {
+		sig[i] = inb(addr + i);
+
+		if (!i && (sig[0] & 0x80))
+			return NULL;
+	}
+
+	sig_str[0] = ((sig[0] >> 2) & 0x1f) + ('A' - 1);
+	sig_str[1] = (((sig[0] & 3) << 3) | (sig[1] >> 5)) + ('A' - 1);
+	sig_str[2] = (sig[1] & 0x1f) + ('A' - 1);
+	rev = (sig[2] << 8) | sig[3];
+	sprintf(sig_str + 3, "%04X", rev);
+
+	return sig_str;
+}
+
+static irqreturn_t ip22_eisa_intr(int irq, void *dev_id)
+{
+	u8 eisa_irq = inb(EIU_INTRPT_ACK);
+
+	inb(EISA_DMA1_STATUS);
+	inb(EISA_DMA2_STATUS);
+
+	if (eisa_irq < EISA_MAX_IRQ) {
+		do_IRQ(eisa_irq);
+		return IRQ_HANDLED;
+	}
+
+	/* Oops, Bad Stuff Happened... */
+	printk(KERN_ERR "eisa_irq %d out of bound\n", eisa_irq);
+
+	outb(0x20, EISA_INT2_CTRL);
+	outb(0x20, EISA_INT1_CTRL);
+
+	return IRQ_NONE;
+}
+
+int __init ip22_eisa_init(void)
+{
+	int i, c;
+	char *str;
+
+	if (!(sgimc->systemid & SGIMC_SYSID_EPRESENT)) {
+		printk(KERN_INFO "EISA: bus not present.\n");
+		return 1;
+	}
+
+	printk(KERN_INFO "EISA: Probing bus...\n");
+	for (c = 0, i = 1; i <= IP22_EISA_MAX_SLOTS; i++) {
+		if ((str = decode_eisa_sig(0x1000 * i + EISA_VENDOR_ID_OFFSET))) {
+			printk(KERN_INFO "EISA: slot %d : %s detected.\n",
+			       i, str);
+			c++;
+		}
+	}
+	printk(KERN_INFO "EISA: Detected %d card%s.\n", c, c < 2 ? "" : "s");
+#ifdef CONFIG_ISA
+	printk(KERN_INFO "ISA support compiled in.\n");
+#endif
+
+	/* Warning : BlackMagicAhead(tm).
+	   Please wave your favorite dead chicken over the busses */
+
+	/* First say hello to the EIU */
+	outl(0x0000FFFF, EIU_PREMPT_REG);
+	outl(1, EIU_QUIET_REG);
+	outl(0x40f3c07F, EIU_MODE_REG);
+
+	/* Now be nice to the EISA chipset */
+	outb(1, EISA_EXT_NMI_RESET_CTRL);
+	udelay(50);	/* Wait long enough for the dust to settle */
+	outb(0, EISA_EXT_NMI_RESET_CTRL);
+	outb(0, EISA_DMA2_WRITE_SINGLE);
+
+	init_i8259_irqs();
+
+	if (request_irq(SGI_EISA_IRQ, ip22_eisa_intr, 0, "EISA", NULL))
+		pr_err("Failed to request irq %d (EISA)\n", SGI_EISA_IRQ);
+
+	EISA_bus = 1;
+	return 0;
+}
diff --git a/arch/mips/sgi-ip22/ip22-gio.c b/arch/mips/sgi-ip22/ip22-gio.c
new file mode 100644
index 000000000..8686e8c1c
--- /dev/null
+++ b/arch/mips/sgi-ip22/ip22-gio.c
@@ -0,0 +1,432 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include <linux/export.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+
+#include <asm/addrspace.h>
+#include <asm/paccess.h>
+#include <asm/gio_device.h>
+#include <asm/sgi/gio.h>
+#include <asm/sgi/hpc3.h>
+#include <asm/sgi/mc.h>
+#include <asm/sgi/ip22.h>
+
+static struct bus_type gio_bus_type;
+
+static struct {
+	const char *name;
+	__u8	   id;
+} gio_name_table[] = {
+	{ .name = "SGI Impact", .id = 0x10 },
+	{ .name = "Phobos G160", .id = 0x35 },
+	{ .name = "Phobos G130", .id = 0x36 },
+	{ .name = "Phobos G100", .id = 0x37 },
+	{ .name = "Set Engineering GFE", .id = 0x38 },
+	/* fake IDs */
+	{ .name = "SGI Newport", .id = 0x7e },
+	{ .name = "SGI GR2/GR3", .id = 0x7f },
+};
+
+static void gio_bus_release(struct device *dev)
+{
+	kfree(dev);
+}
+
+static struct device gio_bus = {
+	.init_name = "gio",
+	.release = &gio_bus_release,
+};
+
+/**
+ * gio_match_device - Tell if an of_device structure has a matching
+ * gio_match structure
+ * @ids: array of of device match structures to search in
+ * @dev: the of device structure to match against
+ *
+ * Used by a driver to check whether an of_device present in the
+ * system is in its list of supported devices.
+ */
+static const struct gio_device_id *
+gio_match_device(const struct gio_device_id *match,
+		 const struct gio_device *dev)
+{
+	const struct gio_device_id *ids;
+
+	for (ids = match; ids->id != 0xff; ids++)
+		if (ids->id == dev->id.id)
+			return ids;
+
+	return NULL;
+}
+
+struct gio_device *gio_dev_get(struct gio_device *dev)
+{
+	struct device *tmp;
+
+	if (!dev)
+		return NULL;
+	tmp = get_device(&dev->dev);
+	if (tmp)
+		return to_gio_device(tmp);
+	else
+		return NULL;
+}
+EXPORT_SYMBOL_GPL(gio_dev_get);
+
+void gio_dev_put(struct gio_device *dev)
+{
+	if (dev)
+		put_device(&dev->dev);
+}
+EXPORT_SYMBOL_GPL(gio_dev_put);
+
+/**
+ * gio_release_dev - free an gio device structure when all users of it are finished.
+ * @dev: device that's been disconnected
+ *
+ * Will be called only by the device core when all users of this gio device are
+ * done.
+ */
+void gio_release_dev(struct device *dev)
+{
+	struct gio_device *giodev;
+
+	giodev = to_gio_device(dev);
+	kfree(giodev);
+}
+EXPORT_SYMBOL_GPL(gio_release_dev);
+
+int gio_device_register(struct gio_device *giodev)
+{
+	giodev->dev.bus = &gio_bus_type;
+	giodev->dev.parent = &gio_bus;
+	return device_register(&giodev->dev);
+}
+EXPORT_SYMBOL_GPL(gio_device_register);
+
+void gio_device_unregister(struct gio_device *giodev)
+{
+	device_unregister(&giodev->dev);
+}
+EXPORT_SYMBOL_GPL(gio_device_unregister);
+
+static int gio_bus_match(struct device *dev, struct device_driver *drv)
+{
+	struct gio_device *gio_dev = to_gio_device(dev);
+	struct gio_driver *gio_drv = to_gio_driver(drv);
+
+	return gio_match_device(gio_drv->id_table, gio_dev) != NULL;
+}
+
+static int gio_device_probe(struct device *dev)
+{
+	int error = -ENODEV;
+	struct gio_driver *drv;
+	struct gio_device *gio_dev;
+	const struct gio_device_id *match;
+
+	drv = to_gio_driver(dev->driver);
+	gio_dev = to_gio_device(dev);
+
+	if (!drv->probe)
+		return error;
+
+	gio_dev_get(gio_dev);
+
+	match = gio_match_device(drv->id_table, gio_dev);
+	if (match)
+		error = drv->probe(gio_dev, match);
+	if (error)
+		gio_dev_put(gio_dev);
+
+	return error;
+}
+
+static void gio_device_remove(struct device *dev)
+{
+	struct gio_device *gio_dev = to_gio_device(dev);
+	struct gio_driver *drv = to_gio_driver(dev->driver);
+
+	if (drv->remove)
+		drv->remove(gio_dev);
+}
+
+static void gio_device_shutdown(struct device *dev)
+{
+	struct gio_device *gio_dev = to_gio_device(dev);
+	struct gio_driver *drv = to_gio_driver(dev->driver);
+
+	if (dev->driver && drv->shutdown)
+		drv->shutdown(gio_dev);
+}
+
+static ssize_t modalias_show(struct device *dev, struct device_attribute *a,
+			     char *buf)
+{
+	struct gio_device *gio_dev = to_gio_device(dev);
+	int len = snprintf(buf, PAGE_SIZE, "gio:%x\n", gio_dev->id.id);
+
+	return (len >= PAGE_SIZE) ? (PAGE_SIZE - 1) : len;
+}
+static DEVICE_ATTR_RO(modalias);
+
+static ssize_t name_show(struct device *dev,
+			 struct device_attribute *attr, char *buf)
+{
+	struct gio_device *giodev;
+
+	giodev = to_gio_device(dev);
+	return sprintf(buf, "%s", giodev->name);
+}
+static DEVICE_ATTR_RO(name);
+
+static ssize_t id_show(struct device *dev,
+		       struct device_attribute *attr, char *buf)
+{
+	struct gio_device *giodev;
+
+	giodev = to_gio_device(dev);
+	return sprintf(buf, "%x", giodev->id.id);
+}
+static DEVICE_ATTR_RO(id);
+
+static struct attribute *gio_dev_attrs[] = {
+	&dev_attr_modalias.attr,
+	&dev_attr_name.attr,
+	&dev_attr_id.attr,
+	NULL,
+};
+ATTRIBUTE_GROUPS(gio_dev);
+
+static int gio_device_uevent(struct device *dev, struct kobj_uevent_env *env)
+{
+	struct gio_device *gio_dev = to_gio_device(dev);
+
+	add_uevent_var(env, "MODALIAS=gio:%x", gio_dev->id.id);
+	return 0;
+}
+
+int gio_register_driver(struct gio_driver *drv)
+{
+	/* initialize common driver fields */
+	if (!drv->driver.name)
+		drv->driver.name = drv->name;
+	if (!drv->driver.owner)
+		drv->driver.owner = drv->owner;
+	drv->driver.bus = &gio_bus_type;
+
+	/* register with core */
+	return driver_register(&drv->driver);
+}
+EXPORT_SYMBOL_GPL(gio_register_driver);
+
+void gio_unregister_driver(struct gio_driver *drv)
+{
+	driver_unregister(&drv->driver);
+}
+EXPORT_SYMBOL_GPL(gio_unregister_driver);
+
+void gio_set_master(struct gio_device *dev)
+{
+	u32 tmp = sgimc->giopar;
+
+	switch (dev->slotno) {
+	case 0:
+		tmp |= SGIMC_GIOPAR_MASTERGFX;
+		break;
+	case 1:
+		tmp |= SGIMC_GIOPAR_MASTEREXP0;
+		break;
+	case 2:
+		tmp |= SGIMC_GIOPAR_MASTEREXP1;
+		break;
+	}
+	sgimc->giopar = tmp;
+}
+EXPORT_SYMBOL_GPL(gio_set_master);
+
+void ip22_gio_set_64bit(int slotno)
+{
+	u32 tmp = sgimc->giopar;
+
+	switch (slotno) {
+	case 0:
+		tmp |= SGIMC_GIOPAR_GFX64;
+		break;
+	case 1:
+		tmp |= SGIMC_GIOPAR_EXP064;
+		break;
+	case 2:
+		tmp |= SGIMC_GIOPAR_EXP164;
+		break;
+	}
+	sgimc->giopar = tmp;
+}
+
+static int ip22_gio_id(unsigned long addr, u32 *res)
+{
+	u8 tmp8;
+	u8 tmp16;
+	u32 tmp32;
+	u8 *ptr8;
+	u16 *ptr16;
+	u32 *ptr32;
+
+	ptr32 = (void *)CKSEG1ADDR(addr);
+	if (!get_dbe(tmp32, ptr32)) {
+		/*
+		 * We got no DBE, but this doesn't mean anything.
+		 * If GIO is pipelined (which can't be disabled
+		 * for GFX slot) we don't get a DBE, but we see
+		 * the transfer size as data. So we do an 8bit
+		 * and a 16bit access and check whether the common
+		 * data matches
+		 */
+		ptr8 = (void *)CKSEG1ADDR(addr + 3);
+		if (get_dbe(tmp8, ptr8)) {
+			/*
+			 * 32bit access worked, but 8bit doesn't
+			 * so we don't see phantom reads on
+			 * a pipelined bus, but a real card which
+			 * doesn't support 8 bit reads
+			 */
+			*res = tmp32;
+			return 1;
+		}
+		ptr16 = (void *)CKSEG1ADDR(addr + 2);
+		get_dbe(tmp16, ptr16);
+		if (tmp8 == (tmp16 & 0xff) &&
+		    tmp8 == (tmp32 & 0xff) &&
+		    tmp16 == (tmp32 & 0xffff)) {
+			*res = tmp32;
+			return 1;
+		}
+	}
+	return 0; /* nothing here */
+}
+
+#define HQ2_MYSTERY_OFFS       0x6A07C
+#define NEWPORT_USTATUS_OFFS   0xF133C
+
+static int ip22_is_gr2(unsigned long addr)
+{
+	u32 tmp;
+	u32 *ptr;
+
+	/* HQ2 only allows 32bit accesses */
+	ptr = (void *)CKSEG1ADDR(addr + HQ2_MYSTERY_OFFS);
+	if (!get_dbe(tmp, ptr)) {
+		if (tmp == 0xdeadbeef)
+			return 1;
+	}
+	return 0;
+}
+
+
+static void ip22_check_gio(int slotno, unsigned long addr, int irq)
+{
+	const char *name = "Unknown";
+	struct gio_device *gio_dev;
+	u32 tmp;
+	__u8 id;
+	int i;
+
+	/* first look for GR2/GR3 by checking mystery register */
+	if (ip22_is_gr2(addr))
+		tmp = 0x7f;
+	else {
+		if (!ip22_gio_id(addr, &tmp)) {
+			/*
+			 * no GIO signature at start address of slot
+			 * since Newport doesn't have one, we check if
+			 * user status register is readable
+			 */
+			if (ip22_gio_id(addr + NEWPORT_USTATUS_OFFS, &tmp))
+				tmp = 0x7e;
+			else
+				tmp = 0;
+		}
+	}
+	if (tmp) {
+		id = GIO_ID(tmp);
+		if (tmp & GIO_32BIT_ID) {
+			if (tmp & GIO_64BIT_IFACE)
+				ip22_gio_set_64bit(slotno);
+		}
+		for (i = 0; i < ARRAY_SIZE(gio_name_table); i++) {
+			if (id == gio_name_table[i].id) {
+				name = gio_name_table[i].name;
+				break;
+			}
+		}
+		printk(KERN_INFO "GIO: slot %d : %s (id %x)\n",
+		       slotno, name, id);
+		gio_dev = kzalloc(sizeof *gio_dev, GFP_KERNEL);
+		if (!gio_dev)
+			return;
+		gio_dev->name = name;
+		gio_dev->slotno = slotno;
+		gio_dev->id.id = id;
+		gio_dev->resource.start = addr;
+		gio_dev->resource.end = addr + 0x3fffff;
+		gio_dev->resource.flags = IORESOURCE_MEM;
+		gio_dev->irq = irq;
+		dev_set_name(&gio_dev->dev, "%d", slotno);
+		gio_device_register(gio_dev);
+	} else
+		printk(KERN_INFO "GIO: slot %d : Empty\n", slotno);
+}
+
+static struct bus_type gio_bus_type = {
+	.name	   = "gio",
+	.dev_groups = gio_dev_groups,
+	.match	   = gio_bus_match,
+	.probe	   = gio_device_probe,
+	.remove	   = gio_device_remove,
+	.shutdown  = gio_device_shutdown,
+	.uevent	   = gio_device_uevent,
+};
+
+static struct resource gio_bus_resource = {
+	.start = GIO_SLOT_GFX_BASE,
+	.end   = GIO_SLOT_GFX_BASE + 0x9fffff,
+	.name  = "GIO Bus",
+	.flags = IORESOURCE_MEM,
+};
+
+int __init ip22_gio_init(void)
+{
+	unsigned int pbdma __maybe_unused;
+	int ret;
+
+	ret = device_register(&gio_bus);
+	if (ret) {
+		put_device(&gio_bus);
+		return ret;
+	}
+
+	ret = bus_register(&gio_bus_type);
+	if (!ret) {
+		request_resource(&iomem_resource, &gio_bus_resource);
+		printk(KERN_INFO "GIO: Probing bus...\n");
+
+		if (ip22_is_fullhouse()) {
+			/* Indigo2 */
+			ip22_check_gio(0, GIO_SLOT_GFX_BASE, SGI_GIO_1_IRQ);
+			ip22_check_gio(1, GIO_SLOT_EXP0_BASE, SGI_GIO_1_IRQ);
+		} else {
+			/* Indy/Challenge S */
+			if (get_dbe(pbdma, (unsigned int *)&hpc3c1->pbdma[1]))
+				ip22_check_gio(0, GIO_SLOT_GFX_BASE,
+					       SGI_GIO_0_IRQ);
+			ip22_check_gio(1, GIO_SLOT_EXP0_BASE, SGI_GIOEXP0_IRQ);
+			ip22_check_gio(2, GIO_SLOT_EXP1_BASE, SGI_GIOEXP1_IRQ);
+		}
+	} else
+		device_unregister(&gio_bus);
+
+	return ret;
+}
+
+subsys_initcall(ip22_gio_init);
diff --git a/arch/mips/sgi-ip22/ip22-hpc.c b/arch/mips/sgi-ip22/ip22-hpc.c
new file mode 100644
index 000000000..49922e86c
--- /dev/null
+++ b/arch/mips/sgi-ip22/ip22-hpc.c
@@ -0,0 +1,64 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ip22-hpc.c: Routines for generic manipulation of the HPC controllers.
+ *
+ * Copyright (C) 1996 David S. Miller (davem@davemloft.net)
+ * Copyright (C) 1998 Ralf Baechle
+ */
+
+#include <linux/export.h>
+#include <linux/init.h>
+#include <linux/types.h>
+
+#include <asm/io.h>
+#include <asm/sgi/hpc3.h>
+#include <asm/sgi/ioc.h>
+#include <asm/sgi/ip22.h>
+
+struct hpc3_regs *hpc3c0, *hpc3c1;
+
+EXPORT_SYMBOL(hpc3c0);
+EXPORT_SYMBOL(hpc3c1);
+
+struct sgioc_regs *sgioc;
+
+EXPORT_SYMBOL(sgioc);
+
+/* We need software copies of these because they are write only. */
+u8 sgi_ioc_reset, sgi_ioc_write;
+
+extern char *system_type;
+
+void __init sgihpc_init(void)
+{
+	/* ioremap can't fail */
+	hpc3c0 = (struct hpc3_regs *)
+		 ioremap(HPC3_CHIP0_BASE, sizeof(struct hpc3_regs));
+	hpc3c1 = (struct hpc3_regs *)
+		 ioremap(HPC3_CHIP1_BASE, sizeof(struct hpc3_regs));
+	/* IOC lives in PBUS PIO channel 6 */
+	sgioc = (struct sgioc_regs *)hpc3c0->pbus_extregs[6];
+
+	hpc3c0->pbus_piocfg[6][0] |= HPC3_PIOCFG_DS16;
+	if (ip22_is_fullhouse()) {
+		/* Full House comes with INT2 which lives in PBUS PIO
+		 * channel 4 */
+		sgint = (struct sgint_regs *)hpc3c0->pbus_extregs[4];
+		system_type = "SGI Indigo2";
+	} else {
+		/* Guiness comes with INT3 which is part of IOC */
+		sgint = &sgioc->int3;
+		system_type = "SGI Indy";
+	}
+
+	sgi_ioc_reset = (SGIOC_RESET_PPORT | SGIOC_RESET_KBDMOUSE |
+			 SGIOC_RESET_EISA | SGIOC_RESET_ISDN |
+			 SGIOC_RESET_LC0OFF);
+
+	sgi_ioc_write = (SGIOC_WRITE_EASEL | SGIOC_WRITE_NTHRESH |
+			 SGIOC_WRITE_TPSPEED | SGIOC_WRITE_EPSEL |
+			 SGIOC_WRITE_U0AMODE | SGIOC_WRITE_U1AMODE);
+
+	sgioc->reset = sgi_ioc_reset;
+	sgioc->write = sgi_ioc_write;
+}
diff --git a/arch/mips/sgi-ip22/ip22-int.c b/arch/mips/sgi-ip22/ip22-int.c
new file mode 100644
index 000000000..96798a4ab
--- /dev/null
+++ b/arch/mips/sgi-ip22/ip22-int.c
@@ -0,0 +1,320 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ip22-int.c: Routines for generic manipulation of the INT[23] ASIC
+ *	       found on INDY and Indigo2 workstations.
+ *
+ * Copyright (C) 1996 David S. Miller (davem@davemloft.net)
+ * Copyright (C) 1997, 1998 Ralf Baechle (ralf@gnu.org)
+ * Copyright (C) 1999 Andrew R. Baker (andrewb@uab.edu)
+ *		      - Indigo2 changes
+ *		      - Interrupt handling fixes
+ * Copyright (C) 2001, 2003 Ladislav Michl (ladis@linux-mips.org)
+ */
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/kernel_stat.h>
+#include <linux/interrupt.h>
+#include <linux/ftrace.h>
+
+#include <asm/irq_cpu.h>
+#include <asm/sgi/hpc3.h>
+#include <asm/sgi/ip22.h>
+
+/* So far nothing hangs here */
+#undef USE_LIO3_IRQ
+
+struct sgint_regs *sgint;
+
+static char lc0msk_to_irqnr[256];
+static char lc1msk_to_irqnr[256];
+static char lc2msk_to_irqnr[256];
+static char lc3msk_to_irqnr[256];
+
+extern int ip22_eisa_init(void);
+
+static void enable_local0_irq(struct irq_data *d)
+{
+	/* don't allow mappable interrupt to be enabled from setup_irq,
+	 * we have our own way to do so */
+	if (d->irq != SGI_MAP_0_IRQ)
+		sgint->imask0 |= (1 << (d->irq - SGINT_LOCAL0));
+}
+
+static void disable_local0_irq(struct irq_data *d)
+{
+	sgint->imask0 &= ~(1 << (d->irq - SGINT_LOCAL0));
+}
+
+static struct irq_chip ip22_local0_irq_type = {
+	.name		= "IP22 local 0",
+	.irq_mask	= disable_local0_irq,
+	.irq_unmask	= enable_local0_irq,
+};
+
+static void enable_local1_irq(struct irq_data *d)
+{
+	/* don't allow mappable interrupt to be enabled from setup_irq,
+	 * we have our own way to do so */
+	if (d->irq != SGI_MAP_1_IRQ)
+		sgint->imask1 |= (1 << (d->irq - SGINT_LOCAL1));
+}
+
+static void disable_local1_irq(struct irq_data *d)
+{
+	sgint->imask1 &= ~(1 << (d->irq - SGINT_LOCAL1));
+}
+
+static struct irq_chip ip22_local1_irq_type = {
+	.name		= "IP22 local 1",
+	.irq_mask	= disable_local1_irq,
+	.irq_unmask	= enable_local1_irq,
+};
+
+static void enable_local2_irq(struct irq_data *d)
+{
+	sgint->imask0 |= (1 << (SGI_MAP_0_IRQ - SGINT_LOCAL0));
+	sgint->cmeimask0 |= (1 << (d->irq - SGINT_LOCAL2));
+}
+
+static void disable_local2_irq(struct irq_data *d)
+{
+	sgint->cmeimask0 &= ~(1 << (d->irq - SGINT_LOCAL2));
+	if (!sgint->cmeimask0)
+		sgint->imask0 &= ~(1 << (SGI_MAP_0_IRQ - SGINT_LOCAL0));
+}
+
+static struct irq_chip ip22_local2_irq_type = {
+	.name		= "IP22 local 2",
+	.irq_mask	= disable_local2_irq,
+	.irq_unmask	= enable_local2_irq,
+};
+
+static void enable_local3_irq(struct irq_data *d)
+{
+	sgint->imask1 |= (1 << (SGI_MAP_1_IRQ - SGINT_LOCAL1));
+	sgint->cmeimask1 |= (1 << (d->irq - SGINT_LOCAL3));
+}
+
+static void disable_local3_irq(struct irq_data *d)
+{
+	sgint->cmeimask1 &= ~(1 << (d->irq - SGINT_LOCAL3));
+	if (!sgint->cmeimask1)
+		sgint->imask1 &= ~(1 << (SGI_MAP_1_IRQ - SGINT_LOCAL1));
+}
+
+static struct irq_chip ip22_local3_irq_type = {
+	.name		= "IP22 local 3",
+	.irq_mask	= disable_local3_irq,
+	.irq_unmask	= enable_local3_irq,
+};
+
+static void indy_local0_irqdispatch(void)
+{
+	u8 mask = sgint->istat0 & sgint->imask0;
+	u8 mask2;
+	int irq;
+
+	if (mask & SGINT_ISTAT0_LIO2) {
+		mask2 = sgint->vmeistat & sgint->cmeimask0;
+		irq = lc2msk_to_irqnr[mask2];
+	} else
+		irq = lc0msk_to_irqnr[mask];
+
+	/*
+	 * workaround for INT2 bug; if irq == 0, INT2 has seen a fifo full
+	 * irq, but failed to latch it into status register
+	 */
+	if (irq)
+		do_IRQ(irq);
+	else
+		do_IRQ(SGINT_LOCAL0 + 0);
+}
+
+static void indy_local1_irqdispatch(void)
+{
+	u8 mask = sgint->istat1 & sgint->imask1;
+	u8 mask2;
+	int irq;
+
+	if (mask & SGINT_ISTAT1_LIO3) {
+		mask2 = sgint->vmeistat & sgint->cmeimask1;
+		irq = lc3msk_to_irqnr[mask2];
+	} else
+		irq = lc1msk_to_irqnr[mask];
+
+	/* if irq == 0, then the interrupt has already been cleared */
+	if (irq)
+		do_IRQ(irq);
+}
+
+extern void ip22_be_interrupt(int irq);
+
+static void __irq_entry indy_buserror_irq(void)
+{
+	int irq = SGI_BUSERR_IRQ;
+
+	irq_enter();
+	kstat_incr_irq_this_cpu(irq);
+	ip22_be_interrupt(irq);
+	irq_exit();
+}
+
+#ifdef USE_LIO3_IRQ
+#define SGI_INTERRUPTS	SGINT_END
+#else
+#define SGI_INTERRUPTS	SGINT_LOCAL3
+#endif
+
+extern void indy_8254timer_irq(void);
+
+/*
+ * IRQs on the INDY look basically (barring software IRQs which we don't use
+ * at all) like:
+ *
+ *	MIPS IRQ	Source
+ *	--------	------
+ *	       0	Software (ignored)
+ *	       1	Software (ignored)
+ *	       2	Local IRQ level zero
+ *	       3	Local IRQ level one
+ *	       4	8254 Timer zero
+ *	       5	8254 Timer one
+ *	       6	Bus Error
+ *	       7	R4k timer (what we use)
+ *
+ * We handle the IRQ according to _our_ priority which is:
+ *
+ * Highest ----	    R4k Timer
+ *		    Local IRQ zero
+ *		    Local IRQ one
+ *		    Bus Error
+ *		    8254 Timer zero
+ * Lowest  ----	    8254 Timer one
+ *
+ * then we just return, if multiple IRQs are pending then we will just take
+ * another exception, big deal.
+ */
+
+asmlinkage void plat_irq_dispatch(void)
+{
+	unsigned int pending = read_c0_status() & read_c0_cause();
+
+	/*
+	 * First we check for r4k counter/timer IRQ.
+	 */
+	if (pending & CAUSEF_IP7)
+		do_IRQ(SGI_TIMER_IRQ);
+	else if (pending & CAUSEF_IP2)
+		indy_local0_irqdispatch();
+	else if (pending & CAUSEF_IP3)
+		indy_local1_irqdispatch();
+	else if (pending & CAUSEF_IP6)
+		indy_buserror_irq();
+	else if (pending & (CAUSEF_IP4 | CAUSEF_IP5))
+		indy_8254timer_irq();
+}
+
+void __init arch_init_irq(void)
+{
+	int i;
+
+	/* Init local mask --> irq tables. */
+	for (i = 0; i < 256; i++) {
+		if (i & 0x80) {
+			lc0msk_to_irqnr[i] = SGINT_LOCAL0 + 7;
+			lc1msk_to_irqnr[i] = SGINT_LOCAL1 + 7;
+			lc2msk_to_irqnr[i] = SGINT_LOCAL2 + 7;
+			lc3msk_to_irqnr[i] = SGINT_LOCAL3 + 7;
+		} else if (i & 0x40) {
+			lc0msk_to_irqnr[i] = SGINT_LOCAL0 + 6;
+			lc1msk_to_irqnr[i] = SGINT_LOCAL1 + 6;
+			lc2msk_to_irqnr[i] = SGINT_LOCAL2 + 6;
+			lc3msk_to_irqnr[i] = SGINT_LOCAL3 + 6;
+		} else if (i & 0x20) {
+			lc0msk_to_irqnr[i] = SGINT_LOCAL0 + 5;
+			lc1msk_to_irqnr[i] = SGINT_LOCAL1 + 5;
+			lc2msk_to_irqnr[i] = SGINT_LOCAL2 + 5;
+			lc3msk_to_irqnr[i] = SGINT_LOCAL3 + 5;
+		} else if (i & 0x10) {
+			lc0msk_to_irqnr[i] = SGINT_LOCAL0 + 4;
+			lc1msk_to_irqnr[i] = SGINT_LOCAL1 + 4;
+			lc2msk_to_irqnr[i] = SGINT_LOCAL2 + 4;
+			lc3msk_to_irqnr[i] = SGINT_LOCAL3 + 4;
+		} else if (i & 0x08) {
+			lc0msk_to_irqnr[i] = SGINT_LOCAL0 + 3;
+			lc1msk_to_irqnr[i] = SGINT_LOCAL1 + 3;
+			lc2msk_to_irqnr[i] = SGINT_LOCAL2 + 3;
+			lc3msk_to_irqnr[i] = SGINT_LOCAL3 + 3;
+		} else if (i & 0x04) {
+			lc0msk_to_irqnr[i] = SGINT_LOCAL0 + 2;
+			lc1msk_to_irqnr[i] = SGINT_LOCAL1 + 2;
+			lc2msk_to_irqnr[i] = SGINT_LOCAL2 + 2;
+			lc3msk_to_irqnr[i] = SGINT_LOCAL3 + 2;
+		} else if (i & 0x02) {
+			lc0msk_to_irqnr[i] = SGINT_LOCAL0 + 1;
+			lc1msk_to_irqnr[i] = SGINT_LOCAL1 + 1;
+			lc2msk_to_irqnr[i] = SGINT_LOCAL2 + 1;
+			lc3msk_to_irqnr[i] = SGINT_LOCAL3 + 1;
+		} else if (i & 0x01) {
+			lc0msk_to_irqnr[i] = SGINT_LOCAL0 + 0;
+			lc1msk_to_irqnr[i] = SGINT_LOCAL1 + 0;
+			lc2msk_to_irqnr[i] = SGINT_LOCAL2 + 0;
+			lc3msk_to_irqnr[i] = SGINT_LOCAL3 + 0;
+		} else {
+			lc0msk_to_irqnr[i] = 0;
+			lc1msk_to_irqnr[i] = 0;
+			lc2msk_to_irqnr[i] = 0;
+			lc3msk_to_irqnr[i] = 0;
+		}
+	}
+
+	/* Mask out all interrupts. */
+	sgint->imask0 = 0;
+	sgint->imask1 = 0;
+	sgint->cmeimask0 = 0;
+	sgint->cmeimask1 = 0;
+
+	/* init CPU irqs */
+	mips_cpu_irq_init();
+
+	for (i = SGINT_LOCAL0; i < SGI_INTERRUPTS; i++) {
+		struct irq_chip *handler;
+
+		if (i < SGINT_LOCAL1)
+			handler		= &ip22_local0_irq_type;
+		else if (i < SGINT_LOCAL2)
+			handler		= &ip22_local1_irq_type;
+		else if (i < SGINT_LOCAL3)
+			handler		= &ip22_local2_irq_type;
+		else
+			handler		= &ip22_local3_irq_type;
+
+		irq_set_chip_and_handler(i, handler, handle_level_irq);
+	}
+
+	/* vector handler. this register the IRQ as non-sharable */
+	if (request_irq(SGI_LOCAL_0_IRQ, no_action, IRQF_NO_THREAD,
+			"local0 cascade", NULL))
+		pr_err("Failed to register local0 cascade interrupt\n");
+	if (request_irq(SGI_LOCAL_1_IRQ, no_action, IRQF_NO_THREAD,
+			"local1 cascade", NULL))
+		pr_err("Failed to register local1 cascade interrupt\n");
+	if (request_irq(SGI_BUSERR_IRQ, no_action, IRQF_NO_THREAD,
+			"Bus Error", NULL))
+		pr_err("Failed to register Bus Error interrupt\n");
+
+	/* cascade in cascade. i love Indy ;-) */
+	if (request_irq(SGI_MAP_0_IRQ, no_action, IRQF_NO_THREAD,
+			"mapable0 cascade", NULL))
+		pr_err("Failed to register mapable0 cascade interrupt\n");
+#ifdef USE_LIO3_IRQ
+	if (request_irq(SGI_MAP_1_IRQ, no_action, IRQF_NO_THREAD,
+			"mapable1 cascade", NULL))
+		pr_err("Failed to register mapable1 cascade interrupt\n");
+#endif
+
+#ifdef CONFIG_EISA
+	if (ip22_is_fullhouse())	/* Only Indigo-2 has EISA stuff */
+		ip22_eisa_init();
+#endif
+}
diff --git a/arch/mips/sgi-ip22/ip22-mc.c b/arch/mips/sgi-ip22/ip22-mc.c
new file mode 100644
index 000000000..74e5b9e27
--- /dev/null
+++ b/arch/mips/sgi-ip22/ip22-mc.c
@@ -0,0 +1,203 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ip22-mc.c: Routines for manipulating SGI Memory Controller.
+ *
+ * Copyright (C) 1996 David S. Miller (davem@davemloft.net)
+ * Copyright (C) 1999 Andrew R. Baker (andrewb@uab.edu) - Indigo2 changes
+ * Copyright (C) 2003 Ladislav Michl  (ladis@linux-mips.org)
+ * Copyright (C) 2004 Peter Fuerst    (pf@net.alphadv.de) - IP28
+ */
+
+#include <linux/init.h>
+#include <linux/export.h>
+#include <linux/kernel.h>
+#include <linux/memblock.h>
+#include <linux/spinlock.h>
+
+#include <asm/io.h>
+#include <asm/bootinfo.h>
+#include <asm/sgialib.h>
+#include <asm/sgi/mc.h>
+#include <asm/sgi/hpc3.h>
+#include <asm/sgi/ip22.h>
+
+struct sgimc_regs *sgimc;
+
+EXPORT_SYMBOL(sgimc);
+
+static inline unsigned long get_bank_addr(unsigned int memconfig)
+{
+	return (memconfig & SGIMC_MCONFIG_BASEADDR) << ((sgimc->systemid & SGIMC_SYSID_MASKREV) >= 5 ? 24 : 22);
+}
+
+static inline unsigned long get_bank_size(unsigned int memconfig)
+{
+	return ((memconfig & SGIMC_MCONFIG_RMASK) + 0x0100) << ((sgimc->systemid & SGIMC_SYSID_MASKREV) >= 5 ? 16 : 14);
+}
+
+static inline unsigned int get_bank_config(int bank)
+{
+	unsigned int res = bank > 1 ? sgimc->mconfig1 : sgimc->mconfig0;
+	return bank % 2 ? res & 0xffff : res >> 16;
+}
+
+#if defined(CONFIG_SGI_IP28) || defined(CONFIG_32BIT)
+static void __init probe_memory(void)
+{
+	/* prom detects all usable memory */
+}
+#else
+/*
+ * Detect installed memory, which PROM misses
+ */
+static void __init probe_memory(void)
+{
+	unsigned long addr, size;
+	int i;
+
+	printk(KERN_INFO "MC: Probing memory configuration:\n");
+	for (i = 0; i < 4; i++) {
+		unsigned int tmp = get_bank_config(i);
+		if (!(tmp & SGIMC_MCONFIG_BVALID))
+			continue;
+
+		size = get_bank_size(tmp);
+		addr = get_bank_addr(tmp);
+		printk(KERN_INFO " bank%d: %3ldM @ %08lx\n",
+			i, size / 1024 / 1024, addr);
+
+		if (addr >= SGIMC_SEG1_BADDR)
+			memblock_add(addr, size);
+	}
+}
+#endif
+
+void __init sgimc_init(void)
+{
+	u32 tmp;
+
+	/* ioremap can't fail */
+	sgimc = (struct sgimc_regs *)
+		ioremap(SGIMC_BASE, sizeof(struct sgimc_regs));
+
+	printk(KERN_INFO "MC: SGI memory controller Revision %d\n",
+	       (int) sgimc->systemid & SGIMC_SYSID_MASKREV);
+
+	/* Place the MC into a known state.  This must be done before
+	 * interrupts are first enabled etc.
+	 */
+
+	/* Step 0: Make sure we turn off the watchdog in case it's
+	 *	   still running (which might be the case after a
+	 *	   soft reboot).
+	 */
+	tmp = sgimc->cpuctrl0;
+	tmp &= ~SGIMC_CCTRL0_WDOG;
+	sgimc->cpuctrl0 = tmp;
+
+	/* Step 1: The CPU/GIO error status registers will not latch
+	 *	   up a new error status until the register has been
+	 *	   cleared by the cpu.	These status registers are
+	 *	   cleared by writing any value to them.
+	 */
+	sgimc->cstat = sgimc->gstat = 0;
+
+	/* Step 2: Enable all parity checking in cpu control register
+	 *	   zero.
+	 */
+	/* don't touch parity settings for IP28 */
+	tmp = sgimc->cpuctrl0;
+#ifndef CONFIG_SGI_IP28
+	tmp |= SGIMC_CCTRL0_EPERRGIO | SGIMC_CCTRL0_EPERRMEM;
+#endif
+	tmp |= SGIMC_CCTRL0_R4KNOCHKPARR;
+	sgimc->cpuctrl0 = tmp;
+
+	/* Step 3: Setup the MC write buffer depth, this is controlled
+	 *	   in cpu control register 1 in the lower 4 bits.
+	 */
+	tmp = sgimc->cpuctrl1;
+	tmp &= ~0xf;
+	tmp |= 0xd;
+	sgimc->cpuctrl1 = tmp;
+
+	/* Step 4: Initialize the RPSS divider register to run as fast
+	 *	   as it can correctly operate.	 The register is laid
+	 *	   out as follows:
+	 *
+	 *	   ----------------------------------------
+	 *	   |  RESERVED	|   INCREMENT	| DIVIDER |
+	 *	   ----------------------------------------
+	 *	    31	      16 15	       8 7	 0
+	 *
+	 *	   DIVIDER determines how often a 'tick' happens,
+	 *	   INCREMENT determines by how the RPSS increment
+	 *	   registers value increases at each 'tick'. Thus,
+	 *	   for IP22 we get INCREMENT=1, DIVIDER=1 == 0x101
+	 */
+	sgimc->divider = 0x101;
+
+	/* Step 5: Initialize GIO64 arbitrator configuration register.
+	 *
+	 * NOTE: HPC init code in sgihpc_init() must run before us because
+	 *	 we need to know Guiness vs. FullHouse and the board
+	 *	 revision on this machine. You have been warned.
+	 */
+
+	/* First the basic invariants across all GIO64 implementations. */
+	tmp = sgimc->giopar & SGIMC_GIOPAR_GFX64; /* keep gfx 64bit settings */
+	tmp |= SGIMC_GIOPAR_HPC64;	/* All 1st HPC's interface at 64bits */
+	tmp |= SGIMC_GIOPAR_ONEBUS;	/* Only one physical GIO bus exists */
+
+	if (ip22_is_fullhouse()) {
+		/* Fullhouse specific settings. */
+		if (SGIOC_SYSID_BOARDREV(sgioc->sysid) < 2) {
+			tmp |= SGIMC_GIOPAR_HPC264;	/* 2nd HPC at 64bits */
+			tmp |= SGIMC_GIOPAR_PLINEEXP0;	/* exp0 pipelines */
+			tmp |= SGIMC_GIOPAR_MASTEREXP1; /* exp1 masters */
+			tmp |= SGIMC_GIOPAR_RTIMEEXP0;	/* exp0 is realtime */
+		} else {
+			tmp |= SGIMC_GIOPAR_HPC264;	/* 2nd HPC 64bits */
+			tmp |= SGIMC_GIOPAR_PLINEEXP0;	/* exp[01] pipelined */
+			tmp |= SGIMC_GIOPAR_PLINEEXP1;
+			tmp |= SGIMC_GIOPAR_MASTEREISA; /* EISA masters */
+		}
+	} else {
+		/* Guiness specific settings. */
+		tmp |= SGIMC_GIOPAR_EISA64;	/* MC talks to EISA at 64bits */
+		tmp |= SGIMC_GIOPAR_MASTEREISA; /* EISA bus can act as master */
+	}
+	sgimc->giopar = tmp;	/* poof */
+
+	probe_memory();
+}
+
+#ifdef CONFIG_SGI_IP28
+void __init prom_cleanup(void)
+{
+	u32 mconfig1;
+	unsigned long flags;
+	spinlock_t lock;
+
+	/*
+	 * because ARCS accesses memory uncached we wait until ARCS
+	 * isn't needed any longer, before we switch from slow to
+	 * normal mode
+	 */
+	spin_lock_irqsave(&lock, flags);
+	mconfig1 = sgimc->mconfig1;
+	/* map ECC register */
+	sgimc->mconfig1 = (mconfig1 & 0xffff0000) | 0x2060;
+	iob();
+	/* switch to normal mode */
+	*(unsigned long *)PHYS_TO_XKSEG_UNCACHED(0x60000000) = 0;
+	iob();
+	/* reduce WR_COL */
+	sgimc->cmacc = (sgimc->cmacc & ~0xf) | 4;
+	iob();
+	/* restore old config */
+	sgimc->mconfig1 = mconfig1;
+	iob();
+	spin_unlock_irqrestore(&lock, flags);
+}
+#endif
diff --git a/arch/mips/sgi-ip22/ip22-nvram.c b/arch/mips/sgi-ip22/ip22-nvram.c
new file mode 100644
index 000000000..e727ef519
--- /dev/null
+++ b/arch/mips/sgi-ip22/ip22-nvram.c
@@ -0,0 +1,122 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ip22-nvram.c: NVRAM and serial EEPROM handling.
+ *
+ * Copyright (C) 2003 Ladislav Michl (ladis@linux-mips.org)
+ */
+#include <linux/export.h>
+
+#include <asm/sgi/hpc3.h>
+#include <asm/sgi/ip22.h>
+
+/* Control opcode for serial eeprom  */
+#define EEPROM_READ	0xc000	/* serial memory read */
+#define EEPROM_WEN	0x9800	/* write enable before prog modes */
+#define EEPROM_WRITE	0xa000	/* serial memory write */
+#define EEPROM_WRALL	0x8800	/* write all registers */
+#define EEPROM_WDS	0x8000	/* disable all programming */
+#define EEPROM_PRREAD	0xc000	/* read protect register */
+#define EEPROM_PREN	0x9800	/* enable protect register mode */
+#define EEPROM_PRCLEAR	0xffff	/* clear protect register */
+#define EEPROM_PRWRITE	0xa000	/* write protect register */
+#define EEPROM_PRDS	0x8000	/* disable protect register, forever */
+
+#define EEPROM_EPROT	0x01	/* Protect register enable */
+#define EEPROM_CSEL	0x02	/* Chip select */
+#define EEPROM_ECLK	0x04	/* EEPROM clock */
+#define EEPROM_DATO	0x08	/* Data out */
+#define EEPROM_DATI	0x10	/* Data in */
+
+/* We need to use these functions early... */
+#define delay() ({						\
+	int x;							\
+	for (x=0; x<100000; x++) __asm__ __volatile__(""); })
+
+#define eeprom_cs_on(ptr) ({	\
+	__raw_writel(__raw_readl(ptr) & ~EEPROM_DATO, ptr);	\
+	__raw_writel(__raw_readl(ptr) & ~EEPROM_ECLK, ptr);	\
+	__raw_writel(__raw_readl(ptr) & ~EEPROM_EPROT, ptr);	\
+	delay();						\
+	__raw_writel(__raw_readl(ptr) | EEPROM_CSEL, ptr);	\
+	__raw_writel(__raw_readl(ptr) | EEPROM_ECLK, ptr); })
+
+
+#define eeprom_cs_off(ptr) ({	\
+	__raw_writel(__raw_readl(ptr) & ~EEPROM_ECLK, ptr);	\
+	__raw_writel(__raw_readl(ptr) & ~EEPROM_CSEL, ptr);	\
+	__raw_writel(__raw_readl(ptr) | EEPROM_EPROT, ptr);	\
+	__raw_writel(__raw_readl(ptr) | EEPROM_ECLK, ptr); })
+
+#define BITS_IN_COMMAND 11
+/*
+ * clock in the nvram command and the register number. For the
+ * national semiconductor nv ram chip the op code is 3 bits and
+ * the address is 6/8 bits.
+ */
+static inline void eeprom_cmd(unsigned int *ctrl, unsigned cmd, unsigned reg)
+{
+	unsigned short ser_cmd;
+	int i;
+
+	ser_cmd = cmd | (reg << (16 - BITS_IN_COMMAND));
+	for (i = 0; i < BITS_IN_COMMAND; i++) {
+		if (ser_cmd & (1<<15))	/* if high order bit set */
+			__raw_writel(__raw_readl(ctrl) | EEPROM_DATO, ctrl);
+		else
+			__raw_writel(__raw_readl(ctrl) & ~EEPROM_DATO, ctrl);
+		__raw_writel(__raw_readl(ctrl) & ~EEPROM_ECLK, ctrl);
+		delay();
+		__raw_writel(__raw_readl(ctrl) | EEPROM_ECLK, ctrl);
+		delay();
+		ser_cmd <<= 1;
+	}
+	/* see data sheet timing diagram */
+	__raw_writel(__raw_readl(ctrl) & ~EEPROM_DATO, ctrl);
+}
+
+unsigned short ip22_eeprom_read(unsigned int *ctrl, int reg)
+{
+	unsigned short res = 0;
+	int i;
+
+	__raw_writel(__raw_readl(ctrl) & ~EEPROM_EPROT, ctrl);
+	eeprom_cs_on(ctrl);
+	eeprom_cmd(ctrl, EEPROM_READ, reg);
+
+	/* clock the data ouf of serial mem */
+	for (i = 0; i < 16; i++) {
+		__raw_writel(__raw_readl(ctrl) & ~EEPROM_ECLK, ctrl);
+		delay();
+		__raw_writel(__raw_readl(ctrl) | EEPROM_ECLK, ctrl);
+		delay();
+		res <<= 1;
+		if (__raw_readl(ctrl) & EEPROM_DATI)
+			res |= 1;
+	}
+
+	eeprom_cs_off(ctrl);
+
+	return res;
+}
+
+EXPORT_SYMBOL(ip22_eeprom_read);
+
+/*
+ * Read specified register from main NVRAM
+ */
+unsigned short ip22_nvram_read(int reg)
+{
+	if (ip22_is_fullhouse())
+		/* IP22 (Indigo2 aka FullHouse) stores env variables into
+		 * 93CS56 Microwire Bus EEPROM 2048 Bit (128x16) */
+		return ip22_eeprom_read(&hpc3c0->eeprom, reg);
+	else {
+		unsigned short tmp;
+		/* IP24 (Indy aka Guiness) uses DS1386 8K version */
+		reg <<= 1;
+		tmp = hpc3c0->bbram[reg++] & 0xff;
+		return (tmp << 8) | (hpc3c0->bbram[reg] & 0xff);
+	}
+}
+
+EXPORT_SYMBOL(ip22_nvram_read);
diff --git a/arch/mips/sgi-ip22/ip22-platform.c b/arch/mips/sgi-ip22/ip22-platform.c
new file mode 100644
index 000000000..0b2002e02
--- /dev/null
+++ b/arch/mips/sgi-ip22/ip22-platform.c
@@ -0,0 +1,223 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/init.h>
+#include <linux/if_ether.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
+
+#include <asm/paccess.h>
+#include <asm/sgi/ip22.h>
+#include <asm/sgi/hpc3.h>
+#include <asm/sgi/mc.h>
+#include <asm/sgi/seeq.h>
+#include <asm/sgi/wd.h>
+
+static struct resource sgiwd93_0_resources[] = {
+	{
+		.name	= "eth0 irq",
+		.start	= SGI_WD93_0_IRQ,
+		.end	= SGI_WD93_0_IRQ,
+		.flags	= IORESOURCE_IRQ
+	}
+};
+
+static struct sgiwd93_platform_data sgiwd93_0_pd = {
+	.unit	= 0,
+	.irq	= SGI_WD93_0_IRQ,
+};
+
+static u64 sgiwd93_0_dma_mask = DMA_BIT_MASK(32);
+
+static struct platform_device sgiwd93_0_device = {
+	.name		= "sgiwd93",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(sgiwd93_0_resources),
+	.resource	= sgiwd93_0_resources,
+	.dev = {
+		.platform_data = &sgiwd93_0_pd,
+		.dma_mask = &sgiwd93_0_dma_mask,
+		.coherent_dma_mask = DMA_BIT_MASK(32),
+	},
+};
+
+static struct resource sgiwd93_1_resources[] = {
+	{
+		.name	= "eth0 irq",
+		.start	= SGI_WD93_1_IRQ,
+		.end	= SGI_WD93_1_IRQ,
+		.flags	= IORESOURCE_IRQ
+	}
+};
+
+static struct sgiwd93_platform_data sgiwd93_1_pd = {
+	.unit	= 1,
+	.irq	= SGI_WD93_1_IRQ,
+};
+
+static u64 sgiwd93_1_dma_mask = DMA_BIT_MASK(32);
+
+static struct platform_device sgiwd93_1_device = {
+	.name		= "sgiwd93",
+	.id		= 1,
+	.num_resources	= ARRAY_SIZE(sgiwd93_1_resources),
+	.resource	= sgiwd93_1_resources,
+	.dev = {
+		.platform_data = &sgiwd93_1_pd,
+		.dma_mask = &sgiwd93_1_dma_mask,
+		.coherent_dma_mask = DMA_BIT_MASK(32),
+	},
+};
+
+/*
+ * Create a platform device for the GPI port that receives the
+ * image data from the embedded camera.
+ */
+static int __init sgiwd93_devinit(void)
+{
+	int res;
+
+	sgiwd93_0_pd.hregs	= &hpc3c0->scsi_chan0;
+	sgiwd93_0_pd.wdregs	= (unsigned char *) hpc3c0->scsi0_ext;
+
+	res = platform_device_register(&sgiwd93_0_device);
+	if (res)
+		return res;
+
+	if (!ip22_is_fullhouse())
+		return 0;
+
+	sgiwd93_1_pd.hregs	= &hpc3c0->scsi_chan1;
+	sgiwd93_1_pd.wdregs	= (unsigned char *) hpc3c0->scsi1_ext;
+
+	return platform_device_register(&sgiwd93_1_device);
+}
+
+device_initcall(sgiwd93_devinit);
+
+static struct resource sgiseeq_0_resources[] = {
+	{
+		.name	= "eth0 irq",
+		.start	= SGI_ENET_IRQ,
+		.end	= SGI_ENET_IRQ,
+		.flags	= IORESOURCE_IRQ
+	}
+};
+
+static struct sgiseeq_platform_data eth0_pd;
+
+static u64 sgiseeq_dma_mask = DMA_BIT_MASK(32);
+
+static struct platform_device eth0_device = {
+	.name		= "sgiseeq",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(sgiseeq_0_resources),
+	.resource	= sgiseeq_0_resources,
+	.dev = {
+		.platform_data = &eth0_pd,
+		.dma_mask = &sgiseeq_dma_mask,
+		.coherent_dma_mask = DMA_BIT_MASK(32),
+	},
+};
+
+static struct resource sgiseeq_1_resources[] = {
+	{
+		.name	= "eth1 irq",
+		.start	= SGI_GIO_0_IRQ,
+		.end	= SGI_GIO_0_IRQ,
+		.flags	= IORESOURCE_IRQ
+	}
+};
+
+static struct sgiseeq_platform_data eth1_pd;
+
+static struct platform_device eth1_device = {
+	.name		= "sgiseeq",
+	.id		= 1,
+	.num_resources	= ARRAY_SIZE(sgiseeq_1_resources),
+	.resource	= sgiseeq_1_resources,
+	.dev = {
+		.platform_data = &eth1_pd,
+	},
+};
+
+/*
+ * Create a platform device for the GPI port that receives the
+ * image data from the embedded camera.
+ */
+static int __init sgiseeq_devinit(void)
+{
+	unsigned int pbdma __maybe_unused;
+	int res, i;
+
+	eth0_pd.hpc = hpc3c0;
+	eth0_pd.irq = SGI_ENET_IRQ;
+#define EADDR_NVOFS	250
+	for (i = 0; i < 3; i++) {
+		unsigned short tmp = ip22_nvram_read(EADDR_NVOFS / 2 + i);
+
+		eth0_pd.mac[2 * i]     = tmp >> 8;
+		eth0_pd.mac[2 * i + 1] = tmp & 0xff;
+	}
+
+	res = platform_device_register(&eth0_device);
+	if (res)
+		return res;
+
+	/* Second HPC is missing? */
+	if (ip22_is_fullhouse() ||
+	    get_dbe(pbdma, (unsigned int *)&hpc3c1->pbdma[1]))
+		return 0;
+
+	sgimc->giopar |= SGIMC_GIOPAR_MASTEREXP1 | SGIMC_GIOPAR_EXP164 |
+			 SGIMC_GIOPAR_HPC264;
+	hpc3c1->pbus_piocfg[0][0] = 0x3ffff;
+	/* interrupt/config register on Challenge S Mezz board */
+	hpc3c1->pbus_extregs[0][0] = 0x30;
+
+	eth1_pd.hpc = hpc3c1;
+	eth1_pd.irq = SGI_GIO_0_IRQ;
+#define EADDR_NVOFS	250
+	for (i = 0; i < 3; i++) {
+		unsigned short tmp = ip22_eeprom_read(&hpc3c1->eeprom,
+						      EADDR_NVOFS / 2 + i);
+
+		eth1_pd.mac[2 * i]     = tmp >> 8;
+		eth1_pd.mac[2 * i + 1] = tmp & 0xff;
+	}
+
+	return platform_device_register(&eth1_device);
+}
+
+device_initcall(sgiseeq_devinit);
+
+static int __init sgi_hal2_devinit(void)
+{
+	return IS_ERR(platform_device_register_simple("sgihal2", 0, NULL, 0));
+}
+
+device_initcall(sgi_hal2_devinit);
+
+static int __init sgi_button_devinit(void)
+{
+	if (ip22_is_fullhouse())
+		return 0; /* full house has no volume buttons */
+
+	return IS_ERR(platform_device_register_simple("sgibtns", -1, NULL, 0));
+}
+
+device_initcall(sgi_button_devinit);
+
+static int __init sgi_ds1286_devinit(void)
+{
+	struct resource res;
+
+	memset(&res, 0, sizeof(res));
+	res.start = HPC3_CHIP0_BASE + offsetof(struct hpc3_regs, rtcregs);
+	res.end = res.start + sizeof(hpc3c0->rtcregs) - 1;
+	res.flags = IORESOURCE_MEM;
+
+	return IS_ERR(platform_device_register_simple("rtc-ds1286", -1,
+						      &res, 1));
+}
+
+device_initcall(sgi_ds1286_devinit);
diff --git a/arch/mips/sgi-ip22/ip22-reset.c b/arch/mips/sgi-ip22/ip22-reset.c
new file mode 100644
index 000000000..8f0861c58
--- /dev/null
+++ b/arch/mips/sgi-ip22/ip22-reset.c
@@ -0,0 +1,203 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1997, 1998, 2001, 03, 05, 06 by Ralf Baechle
+ */
+#include <linux/linkage.h>
+#include <linux/init.h>
+#include <linux/rtc/ds1286.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/sched/signal.h>
+#include <linux/panic_notifier.h>
+#include <linux/pm.h>
+#include <linux/timer.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/reboot.h>
+#include <asm/sgialib.h>
+#include <asm/sgi/ioc.h>
+#include <asm/sgi/hpc3.h>
+#include <asm/sgi/mc.h>
+#include <asm/sgi/ip22.h>
+
+/*
+ * Just powerdown if init hasn't done after POWERDOWN_TIMEOUT seconds.
+ * I'm not sure if this feature is a good idea, for now it's here just to
+ * make the power button make behave just like under IRIX.
+ */
+#define POWERDOWN_TIMEOUT	120
+
+/*
+ * Blink frequency during reboot grace period and when panicked.
+ */
+#define POWERDOWN_FREQ		(HZ / 4)
+#define PANIC_FREQ		(HZ / 8)
+
+static struct timer_list power_timer, blink_timer, debounce_timer;
+static unsigned long blink_timer_timeout;
+
+#define MACHINE_PANICKED		1
+#define MACHINE_SHUTTING_DOWN	2
+
+static int machine_state;
+
+static void __noreturn sgi_machine_power_off(void)
+{
+	unsigned int tmp;
+
+	local_irq_disable();
+
+	/* Disable watchdog */
+	tmp = hpc3c0->rtcregs[RTC_CMD] & 0xff;
+	hpc3c0->rtcregs[RTC_CMD] = tmp | RTC_WAM;
+	hpc3c0->rtcregs[RTC_WSEC] = 0;
+	hpc3c0->rtcregs[RTC_WHSEC] = 0;
+
+	while (1) {
+		sgioc->panel = ~SGIOC_PANEL_POWERON;
+		/* Good bye cruel world ...  */
+
+		/* If we're still running, we probably got sent an alarm
+		   interrupt.  Read the flag to clear it.  */
+		tmp = hpc3c0->rtcregs[RTC_HOURS_ALARM];
+	}
+}
+
+static void __noreturn sgi_machine_restart(char *command)
+{
+	if (machine_state & MACHINE_SHUTTING_DOWN)
+		sgi_machine_power_off();
+	sgimc->cpuctrl0 |= SGIMC_CCTRL0_SYSINIT;
+	while (1);
+}
+
+static void __noreturn sgi_machine_halt(void)
+{
+	if (machine_state & MACHINE_SHUTTING_DOWN)
+		sgi_machine_power_off();
+	ArcEnterInteractiveMode();
+}
+
+static void power_timeout(struct timer_list *unused)
+{
+	sgi_machine_power_off();
+}
+
+static void blink_timeout(struct timer_list *unused)
+{
+	/* XXX fix this for fullhouse  */
+	sgi_ioc_reset ^= (SGIOC_RESET_LC0OFF|SGIOC_RESET_LC1OFF);
+	sgioc->reset = sgi_ioc_reset;
+
+	mod_timer(&blink_timer, jiffies + blink_timer_timeout);
+}
+
+static void debounce(struct timer_list *unused)
+{
+	del_timer(&debounce_timer);
+	if (sgint->istat1 & SGINT_ISTAT1_PWR) {
+		/* Interrupt still being sent. */
+		debounce_timer.expires = jiffies + (HZ / 20); /* 0.05s	*/
+		add_timer(&debounce_timer);
+
+		sgioc->panel = SGIOC_PANEL_POWERON | SGIOC_PANEL_POWERINTR |
+			       SGIOC_PANEL_VOLDNINTR | SGIOC_PANEL_VOLDNHOLD |
+			       SGIOC_PANEL_VOLUPINTR | SGIOC_PANEL_VOLUPHOLD;
+
+		return;
+	}
+
+	if (machine_state & MACHINE_PANICKED)
+		sgimc->cpuctrl0 |= SGIMC_CCTRL0_SYSINIT;
+
+	enable_irq(SGI_PANEL_IRQ);
+}
+
+static inline void power_button(void)
+{
+	if (machine_state & MACHINE_PANICKED)
+		return;
+
+	if ((machine_state & MACHINE_SHUTTING_DOWN) ||
+			kill_cad_pid(SIGINT, 1)) {
+		/* No init process or button pressed twice.  */
+		sgi_machine_power_off();
+	}
+
+	machine_state |= MACHINE_SHUTTING_DOWN;
+	blink_timer_timeout = POWERDOWN_FREQ;
+	blink_timeout(&blink_timer);
+
+	timer_setup(&power_timer, power_timeout, 0);
+	power_timer.expires = jiffies + POWERDOWN_TIMEOUT * HZ;
+	add_timer(&power_timer);
+}
+
+static irqreturn_t panel_int(int irq, void *dev_id)
+{
+	unsigned int buttons;
+
+	buttons = sgioc->panel;
+	sgioc->panel = SGIOC_PANEL_POWERON | SGIOC_PANEL_POWERINTR;
+
+	if (sgint->istat1 & SGINT_ISTAT1_PWR) {
+		/* Wait until interrupt goes away */
+		disable_irq_nosync(SGI_PANEL_IRQ);
+		timer_setup(&debounce_timer, debounce, 0);
+		debounce_timer.expires = jiffies + 5;
+		add_timer(&debounce_timer);
+	}
+
+	/* Power button was pressed
+	 * ioc.ps page 22: "The Panel Register is called Power Control by Full
+	 * House. Only lowest 2 bits are used. Guiness uses upper four bits
+	 * for volume control". This is not true, all bits are pulled high
+	 * on fullhouse */
+	if (!(buttons & SGIOC_PANEL_POWERINTR))
+		power_button();
+
+	return IRQ_HANDLED;
+}
+
+static int panic_event(struct notifier_block *this, unsigned long event,
+		      void *ptr)
+{
+	if (machine_state & MACHINE_PANICKED)
+		return NOTIFY_DONE;
+	machine_state |= MACHINE_PANICKED;
+
+	blink_timer_timeout = PANIC_FREQ;
+	blink_timeout(&blink_timer);
+
+	return NOTIFY_DONE;
+}
+
+static struct notifier_block panic_block = {
+	.notifier_call	= panic_event,
+};
+
+static int __init reboot_setup(void)
+{
+	int res;
+
+	_machine_restart = sgi_machine_restart;
+	_machine_halt = sgi_machine_halt;
+	pm_power_off = sgi_machine_power_off;
+
+	res = request_irq(SGI_PANEL_IRQ, panel_int, 0, "Front Panel", NULL);
+	if (res) {
+		printk(KERN_ERR "Allocation of front panel IRQ failed\n");
+		return res;
+	}
+
+	timer_setup(&blink_timer, blink_timeout, 0);
+	atomic_notifier_chain_register(&panic_notifier_list, &panic_block);
+
+	return 0;
+}
+
+subsys_initcall(reboot_setup);
diff --git a/arch/mips/sgi-ip22/ip22-setup.c b/arch/mips/sgi-ip22/ip22-setup.c
new file mode 100644
index 000000000..b69daa024
--- /dev/null
+++ b/arch/mips/sgi-ip22/ip22-setup.c
@@ -0,0 +1,78 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ip22-setup.c: SGI specific setup, including init of the feature struct.
+ *
+ * Copyright (C) 1996 David S. Miller (davem@davemloft.net)
+ * Copyright (C) 1997, 1998 Ralf Baechle (ralf@gnu.org)
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/kdev_t.h>
+#include <linux/types.h>
+#include <linux/console.h>
+#include <linux/sched.h>
+#include <linux/tty.h>
+
+#include <asm/addrspace.h>
+#include <asm/bcache.h>
+#include <asm/bootinfo.h>
+#include <asm/irq.h>
+#include <asm/reboot.h>
+#include <asm/time.h>
+#include <asm/io.h>
+#include <asm/traps.h>
+#include <asm/sgialib.h>
+#include <asm/sgi/mc.h>
+#include <asm/sgi/hpc3.h>
+#include <asm/sgi/ip22.h>
+
+extern void ip22_be_init(void) __init;
+
+void __init plat_mem_setup(void)
+{
+	char *ctype;
+	char *cserial;
+
+	board_be_init = ip22_be_init;
+
+	/* Init the INDY HPC I/O controller.  Need to call this before
+	 * fucking with the memory controller because it needs to know the
+	 * boardID and whether this is a Guiness or a FullHouse machine.
+	 */
+	sgihpc_init();
+
+	/* Init INDY memory controller. */
+	sgimc_init();
+
+#ifdef CONFIG_BOARD_SCACHE
+	/* Now enable boardcaches, if any. */
+	indy_sc_init();
+#endif
+
+	/* Set EISA IO port base for Indigo2
+	 * ioremap cannot fail */
+	set_io_port_base((unsigned long)ioremap(0x00080000,
+						0x1fffffff - 0x00080000));
+	/* ARCS console environment variable is set to "g?" for
+	 * graphics console, it is set to "d" for the first serial
+	 * line and "d2" for the second serial line.
+	 *
+	 * Need to check if the case is 'g' but no keyboard:
+	 * (ConsoleIn/Out = serial)
+	 */
+	ctype = ArcGetEnvironmentVariable("console");
+	cserial = ArcGetEnvironmentVariable("ConsoleOut");
+
+	if ((ctype && *ctype == 'd') || (cserial && *cserial == 's')) {
+		static char options[8] __initdata;
+		char *baud = ArcGetEnvironmentVariable("dbaud");
+		if (baud)
+			strcpy(options, baud);
+		add_preferred_console("ttyS", *(ctype + 1) == '2' ? 1 : 0,
+				      baud ? options : NULL);
+	} else if (!ctype || *ctype != 'g') {
+		/* Use ARC if we don't want serial ('d') or graphics ('g'). */
+		prom_flags |= PROM_FLAG_USE_AS_CONSOLE;
+		add_preferred_console("arc", 0, NULL);
+	}
+}
diff --git a/arch/mips/sgi-ip22/ip22-time.c b/arch/mips/sgi-ip22/ip22-time.c
new file mode 100644
index 000000000..045aa89f2
--- /dev/null
+++ b/arch/mips/sgi-ip22/ip22-time.c
@@ -0,0 +1,131 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Time operations for IP22 machines. Original code may come from
+ * Ralf Baechle or David S. Miller (sorry guys, i'm really not sure)
+ *
+ * Copyright (C) 2001 by Ladislav Michl
+ * Copyright (C) 2003, 06 Ralf Baechle (ralf@linux-mips.org)
+ */
+#include <linux/bcd.h>
+#include <linux/i8253.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <linux/kernel.h>
+#include <linux/interrupt.h>
+#include <linux/kernel_stat.h>
+#include <linux/time.h>
+#include <linux/ftrace.h>
+
+#include <asm/cpu.h>
+#include <asm/mipsregs.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/time.h>
+#include <asm/sgialib.h>
+#include <asm/sgi/ioc.h>
+#include <asm/sgi/hpc3.h>
+#include <asm/sgi/ip22.h>
+
+static unsigned long dosample(void)
+{
+	u32 ct0, ct1;
+	u8 msb;
+
+	/* Start the counter. */
+	sgint->tcword = (SGINT_TCWORD_CNT2 | SGINT_TCWORD_CALL |
+			 SGINT_TCWORD_MRGEN);
+	sgint->tcnt2 = SGINT_TCSAMP_COUNTER & 0xff;
+	sgint->tcnt2 = SGINT_TCSAMP_COUNTER >> 8;
+
+	/* Get initial counter invariant */
+	ct0 = read_c0_count();
+
+	/* Latch and spin until top byte of counter2 is zero */
+	do {
+		writeb(SGINT_TCWORD_CNT2 | SGINT_TCWORD_CLAT, &sgint->tcword);
+		(void) readb(&sgint->tcnt2);
+		msb = readb(&sgint->tcnt2);
+		ct1 = read_c0_count();
+	} while (msb);
+
+	/* Stop the counter. */
+	writeb(SGINT_TCWORD_CNT2 | SGINT_TCWORD_CALL | SGINT_TCWORD_MSWST,
+	       &sgint->tcword);
+	/*
+	 * Return the difference, this is how far the r4k counter increments
+	 * for every 1/HZ seconds. We round off the nearest 1 MHz of master
+	 * clock (= 1000000 / HZ / 2).
+	 */
+
+	return (ct1 - ct0) / (500000/HZ) * (500000/HZ);
+}
+
+/*
+ * Here we need to calibrate the cycle counter to at least be close.
+ */
+__init void plat_time_init(void)
+{
+	unsigned long r4k_ticks[3];
+	unsigned long r4k_tick;
+
+	/*
+	 * Figure out the r4k offset, the algorithm is very simple and works in
+	 * _all_ cases as long as the 8254 counter register itself works ok (as
+	 * an interrupt driving timer it does not because of bug, this is why
+	 * we are using the onchip r4k counter/compare register to serve this
+	 * purpose, but for r4k_offset calculation it will work ok for us).
+	 * There are other very complicated ways of performing this calculation
+	 * but this one works just fine so I am not going to futz around. ;-)
+	 */
+	printk(KERN_INFO "Calibrating system timer... ");
+	dosample();	/* Prime cache. */
+	dosample();	/* Prime cache. */
+	/* Zero is NOT an option. */
+	do {
+		r4k_ticks[0] = dosample();
+	} while (!r4k_ticks[0]);
+	do {
+		r4k_ticks[1] = dosample();
+	} while (!r4k_ticks[1]);
+
+	if (r4k_ticks[0] != r4k_ticks[1]) {
+		printk("warning: timer counts differ, retrying... ");
+		r4k_ticks[2] = dosample();
+		if (r4k_ticks[2] == r4k_ticks[0]
+		    || r4k_ticks[2] == r4k_ticks[1])
+			r4k_tick = r4k_ticks[2];
+		else {
+			printk("disagreement, using average... ");
+			r4k_tick = (r4k_ticks[0] + r4k_ticks[1]
+				   + r4k_ticks[2]) / 3;
+		}
+	} else
+		r4k_tick = r4k_ticks[0];
+
+	printk("%d [%d.%04d MHz CPU]\n", (int) r4k_tick,
+		(int) (r4k_tick / (500000 / HZ)),
+		(int) (r4k_tick % (500000 / HZ)));
+
+	mips_hpt_frequency = r4k_tick * HZ;
+
+	if (ip22_is_fullhouse())
+		setup_pit_timer();
+}
+
+/* Generic SGI handler for (spurious) 8254 interrupts */
+void __irq_entry indy_8254timer_irq(void)
+{
+	int irq = SGI_8254_0_IRQ;
+	ULONG cnt;
+	char c;
+
+	irq_enter();
+	kstat_incr_irq_this_cpu(irq);
+	printk(KERN_ALERT "Oops, got 8254 interrupt.\n");
+	ArcRead(0, &c, 1, &cnt);
+	ArcEnterInteractiveMode();
+	irq_exit();
+}
diff --git a/arch/mips/sgi-ip22/ip28-berr.c b/arch/mips/sgi-ip22/ip28-berr.c
new file mode 100644
index 000000000..16ca470de
--- /dev/null
+++ b/arch/mips/sgi-ip22/ip28-berr.c
@@ -0,0 +1,488 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ip28-berr.c: Bus error handling.
+ *
+ * Copyright (C) 2002, 2003 Ladislav Michl (ladis@linux-mips.org)
+ * Copyright (C) 2005 Peter Fuerst (pf@net.alphadv.de) - IP28
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/mm.h>
+#include <linux/sched.h>
+#include <linux/sched/debug.h>
+#include <linux/sched/signal.h>
+#include <linux/seq_file.h>
+
+#include <asm/addrspace.h>
+#include <asm/traps.h>
+#include <asm/branch.h>
+#include <asm/irq_regs.h>
+#include <asm/sgi/mc.h>
+#include <asm/sgi/hpc3.h>
+#include <asm/sgi/ioc.h>
+#include <asm/sgi/ip22.h>
+#include <asm/r4kcache.h>
+#include <linux/uaccess.h>
+#include <asm/bootinfo.h>
+
+static unsigned int count_be_is_fixup;
+static unsigned int count_be_handler;
+static unsigned int count_be_interrupt;
+static int debug_be_interrupt;
+
+static unsigned int cpu_err_stat;	/* Status reg for CPU */
+static unsigned int gio_err_stat;	/* Status reg for GIO */
+static unsigned int cpu_err_addr;	/* Error address reg for CPU */
+static unsigned int gio_err_addr;	/* Error address reg for GIO */
+static unsigned int extio_stat;
+static unsigned int hpc3_berr_stat;	/* Bus error interrupt status */
+
+struct hpc3_stat {
+	unsigned long addr;
+	unsigned int ctrl;
+	unsigned int cbp;
+	unsigned int ndptr;
+};
+
+static struct {
+	struct hpc3_stat pbdma[8];
+	struct hpc3_stat scsi[2];
+	struct hpc3_stat ethrx, ethtx;
+} hpc3;
+
+static struct {
+	unsigned long err_addr;
+	struct {
+		u32 lo;
+		u32 hi;
+	} tags[1][2], tagd[4][2], tagi[4][2]; /* Way 0/1 */
+} cache_tags;
+
+static inline void save_cache_tags(unsigned busaddr)
+{
+	unsigned long addr = CAC_BASE | busaddr;
+	int i;
+	cache_tags.err_addr = addr;
+
+	/*
+	 * Starting with a bus-address, save secondary cache (indexed by
+	 * PA[23..18:7..6]) tags first.
+	 */
+	addr &= ~1L;
+#define tag cache_tags.tags[0]
+	cache_op(Index_Load_Tag_S, addr);
+	tag[0].lo = read_c0_taglo();	/* PA[35:18], VA[13:12] */
+	tag[0].hi = read_c0_taghi();	/* PA[39:36] */
+	cache_op(Index_Load_Tag_S, addr | 1L);
+	tag[1].lo = read_c0_taglo();	/* PA[35:18], VA[13:12] */
+	tag[1].hi = read_c0_taghi();	/* PA[39:36] */
+#undef tag
+
+	/*
+	 * Save all primary data cache (indexed by VA[13:5]) tags which
+	 * might fit to this bus-address, knowing that VA[11:0] == PA[11:0].
+	 * Saving all tags and evaluating them later is easier and safer
+	 * than relying on VA[13:12] from the secondary cache tags to pick
+	 * matching primary tags here already.
+	 */
+	addr &= (0xffL << 56) | ((1 << 12) - 1);
+#define tag cache_tags.tagd[i]
+	for (i = 0; i < 4; ++i, addr += (1 << 12)) {
+		cache_op(Index_Load_Tag_D, addr);
+		tag[0].lo = read_c0_taglo();	/* PA[35:12] */
+		tag[0].hi = read_c0_taghi();	/* PA[39:36] */
+		cache_op(Index_Load_Tag_D, addr | 1L);
+		tag[1].lo = read_c0_taglo();	/* PA[35:12] */
+		tag[1].hi = read_c0_taghi();	/* PA[39:36] */
+	}
+#undef tag
+
+	/*
+	 * Save primary instruction cache (indexed by VA[13:6]) tags
+	 * the same way.
+	 */
+	addr &= (0xffL << 56) | ((1 << 12) - 1);
+#define tag cache_tags.tagi[i]
+	for (i = 0; i < 4; ++i, addr += (1 << 12)) {
+		cache_op(Index_Load_Tag_I, addr);
+		tag[0].lo = read_c0_taglo();	/* PA[35:12] */
+		tag[0].hi = read_c0_taghi();	/* PA[39:36] */
+		cache_op(Index_Load_Tag_I, addr | 1L);
+		tag[1].lo = read_c0_taglo();	/* PA[35:12] */
+		tag[1].hi = read_c0_taghi();	/* PA[39:36] */
+	}
+#undef tag
+}
+
+#define GIO_ERRMASK	0xff00
+#define CPU_ERRMASK	0x3f00
+
+static void save_and_clear_buserr(void)
+{
+	int i;
+
+	/* save status registers */
+	cpu_err_addr = sgimc->cerr;
+	cpu_err_stat = sgimc->cstat;
+	gio_err_addr = sgimc->gerr;
+	gio_err_stat = sgimc->gstat;
+	extio_stat = sgioc->extio;
+	hpc3_berr_stat = hpc3c0->bestat;
+
+	hpc3.scsi[0].addr  = (unsigned long)&hpc3c0->scsi_chan0;
+	hpc3.scsi[0].ctrl  = hpc3c0->scsi_chan0.ctrl; /* HPC3_SCTRL_ACTIVE ? */
+	hpc3.scsi[0].cbp   = hpc3c0->scsi_chan0.cbptr;
+	hpc3.scsi[0].ndptr = hpc3c0->scsi_chan0.ndptr;
+
+	hpc3.scsi[1].addr  = (unsigned long)&hpc3c0->scsi_chan1;
+	hpc3.scsi[1].ctrl  = hpc3c0->scsi_chan1.ctrl; /* HPC3_SCTRL_ACTIVE ? */
+	hpc3.scsi[1].cbp   = hpc3c0->scsi_chan1.cbptr;
+	hpc3.scsi[1].ndptr = hpc3c0->scsi_chan1.ndptr;
+
+	hpc3.ethrx.addr	 = (unsigned long)&hpc3c0->ethregs.rx_cbptr;
+	hpc3.ethrx.ctrl	 = hpc3c0->ethregs.rx_ctrl; /* HPC3_ERXCTRL_ACTIVE ? */
+	hpc3.ethrx.cbp	 = hpc3c0->ethregs.rx_cbptr;
+	hpc3.ethrx.ndptr = hpc3c0->ethregs.rx_ndptr;
+
+	hpc3.ethtx.addr	 = (unsigned long)&hpc3c0->ethregs.tx_cbptr;
+	hpc3.ethtx.ctrl	 = hpc3c0->ethregs.tx_ctrl; /* HPC3_ETXCTRL_ACTIVE ? */
+	hpc3.ethtx.cbp	 = hpc3c0->ethregs.tx_cbptr;
+	hpc3.ethtx.ndptr = hpc3c0->ethregs.tx_ndptr;
+
+	for (i = 0; i < 8; ++i) {
+		/* HPC3_PDMACTRL_ISACT ? */
+		hpc3.pbdma[i].addr  = (unsigned long)&hpc3c0->pbdma[i];
+		hpc3.pbdma[i].ctrl  = hpc3c0->pbdma[i].pbdma_ctrl;
+		hpc3.pbdma[i].cbp   = hpc3c0->pbdma[i].pbdma_bptr;
+		hpc3.pbdma[i].ndptr = hpc3c0->pbdma[i].pbdma_dptr;
+	}
+	i = 0;
+	if (gio_err_stat & CPU_ERRMASK)
+		i = gio_err_addr;
+	if (cpu_err_stat & CPU_ERRMASK)
+		i = cpu_err_addr;
+	save_cache_tags(i);
+
+	sgimc->cstat = sgimc->gstat = 0;
+}
+
+static void print_cache_tags(void)
+{
+	u32 scb, scw;
+	int i;
+
+	printk(KERN_ERR "Cache tags @ %08x:\n", (unsigned)cache_tags.err_addr);
+
+	/* PA[31:12] shifted to PTag0 (PA[35:12]) format */
+	scw = (cache_tags.err_addr >> 4) & 0x0fffff00;
+
+	scb = cache_tags.err_addr & ((1 << 12) - 1) & ~((1 << 5) - 1);
+	for (i = 0; i < 4; ++i) { /* for each possible VA[13:12] value */
+		if ((cache_tags.tagd[i][0].lo & 0x0fffff00) != scw &&
+		    (cache_tags.tagd[i][1].lo & 0x0fffff00) != scw)
+		    continue;
+		printk(KERN_ERR
+		       "D: 0: %08x %08x, 1: %08x %08x  (VA[13:5]  %04x)\n",
+			cache_tags.tagd[i][0].hi, cache_tags.tagd[i][0].lo,
+			cache_tags.tagd[i][1].hi, cache_tags.tagd[i][1].lo,
+			scb | (1 << 12)*i);
+	}
+	scb = cache_tags.err_addr & ((1 << 12) - 1) & ~((1 << 6) - 1);
+	for (i = 0; i < 4; ++i) { /* for each possible VA[13:12] value */
+		if ((cache_tags.tagi[i][0].lo & 0x0fffff00) != scw &&
+		    (cache_tags.tagi[i][1].lo & 0x0fffff00) != scw)
+		    continue;
+		printk(KERN_ERR
+		       "I: 0: %08x %08x, 1: %08x %08x  (VA[13:6]  %04x)\n",
+			cache_tags.tagi[i][0].hi, cache_tags.tagi[i][0].lo,
+			cache_tags.tagi[i][1].hi, cache_tags.tagi[i][1].lo,
+			scb | (1 << 12)*i);
+	}
+	i = read_c0_config();
+	scb = i & (1 << 13) ? 7:6;	/* scblksize = 2^[7..6] */
+	scw = ((i >> 16) & 7) + 19 - 1; /* scwaysize = 2^[24..19] / 2 */
+
+	i = ((1 << scw) - 1) & ~((1 << scb) - 1);
+	printk(KERN_ERR "S: 0: %08x %08x, 1: %08x %08x	(PA[%u:%u] %05x)\n",
+		cache_tags.tags[0][0].hi, cache_tags.tags[0][0].lo,
+		cache_tags.tags[0][1].hi, cache_tags.tags[0][1].lo,
+		scw-1, scb, i & (unsigned)cache_tags.err_addr);
+}
+
+static inline const char *cause_excode_text(int cause)
+{
+	static const char *txt[32] =
+	{	"Interrupt",
+		"TLB modification",
+		"TLB (load or instruction fetch)",
+		"TLB (store)",
+		"Address error (load or instruction fetch)",
+		"Address error (store)",
+		"Bus error (instruction fetch)",
+		"Bus error (data: load or store)",
+		"Syscall",
+		"Breakpoint",
+		"Reserved instruction",
+		"Coprocessor unusable",
+		"Arithmetic Overflow",
+		"Trap",
+		"14",
+		"Floating-Point",
+		"16", "17", "18", "19", "20", "21", "22",
+		"Watch Hi/Lo",
+		"24", "25", "26", "27", "28", "29", "30", "31",
+	};
+	return txt[(cause & 0x7c) >> 2];
+}
+
+static void print_buserr(const struct pt_regs *regs)
+{
+	const int field = 2 * sizeof(unsigned long);
+	int error = 0;
+
+	if (extio_stat & EXTIO_MC_BUSERR) {
+		printk(KERN_ERR "MC Bus Error\n");
+		error |= 1;
+	}
+	if (extio_stat & EXTIO_HPC3_BUSERR) {
+		printk(KERN_ERR "HPC3 Bus Error 0x%x:<id=0x%x,%s,lane=0x%x>\n",
+			hpc3_berr_stat,
+			(hpc3_berr_stat & HPC3_BESTAT_PIDMASK) >>
+					  HPC3_BESTAT_PIDSHIFT,
+			(hpc3_berr_stat & HPC3_BESTAT_CTYPE) ? "PIO" : "DMA",
+			hpc3_berr_stat & HPC3_BESTAT_BLMASK);
+		error |= 2;
+	}
+	if (extio_stat & EXTIO_EISA_BUSERR) {
+		printk(KERN_ERR "EISA Bus Error\n");
+		error |= 4;
+	}
+	if (cpu_err_stat & CPU_ERRMASK) {
+		printk(KERN_ERR "CPU error 0x%x<%s%s%s%s%s%s> @ 0x%08x\n",
+			cpu_err_stat,
+			cpu_err_stat & SGIMC_CSTAT_RD ? "RD " : "",
+			cpu_err_stat & SGIMC_CSTAT_PAR ? "PAR " : "",
+			cpu_err_stat & SGIMC_CSTAT_ADDR ? "ADDR " : "",
+			cpu_err_stat & SGIMC_CSTAT_SYSAD_PAR ? "SYSAD " : "",
+			cpu_err_stat & SGIMC_CSTAT_SYSCMD_PAR ? "SYSCMD " : "",
+			cpu_err_stat & SGIMC_CSTAT_BAD_DATA ? "BAD_DATA " : "",
+			cpu_err_addr);
+		error |= 8;
+	}
+	if (gio_err_stat & GIO_ERRMASK) {
+		printk(KERN_ERR "GIO error 0x%x:<%s%s%s%s%s%s%s%s> @ 0x%08x\n",
+			gio_err_stat,
+			gio_err_stat & SGIMC_GSTAT_RD ? "RD " : "",
+			gio_err_stat & SGIMC_GSTAT_WR ? "WR " : "",
+			gio_err_stat & SGIMC_GSTAT_TIME ? "TIME " : "",
+			gio_err_stat & SGIMC_GSTAT_PROM ? "PROM " : "",
+			gio_err_stat & SGIMC_GSTAT_ADDR ? "ADDR " : "",
+			gio_err_stat & SGIMC_GSTAT_BC ? "BC " : "",
+			gio_err_stat & SGIMC_GSTAT_PIO_RD ? "PIO_RD " : "",
+			gio_err_stat & SGIMC_GSTAT_PIO_WR ? "PIO_WR " : "",
+			gio_err_addr);
+		error |= 16;
+	}
+	if (!error)
+		printk(KERN_ERR "MC: Hmm, didn't find any error condition.\n");
+	else {
+		printk(KERN_ERR "CP0: config %08x,  "
+			"MC: cpuctrl0/1: %08x/%05x, giopar: %04x\n"
+			"MC: cpu/gio_memacc: %08x/%05x, memcfg0/1: %08x/%08x\n",
+			read_c0_config(),
+			sgimc->cpuctrl0, sgimc->cpuctrl0, sgimc->giopar,
+			sgimc->cmacc, sgimc->gmacc,
+			sgimc->mconfig0, sgimc->mconfig1);
+		print_cache_tags();
+	}
+	printk(KERN_ALERT "%s, epc == %0*lx, ra == %0*lx\n",
+	       cause_excode_text(regs->cp0_cause),
+	       field, regs->cp0_epc, field, regs->regs[31]);
+}
+
+static int check_microtlb(u32 hi, u32 lo, unsigned long vaddr)
+{
+	/* This is likely rather similar to correct code ;-) */
+
+	vaddr &= 0x7fffffff; /* Doc. states that top bit is ignored */
+
+	/* If tlb-entry is valid and VPN-high (bits [30:21] ?) matches... */
+	if ((lo & 2) && (vaddr >> 21) == ((hi<<1) >> 22)) {
+		u32 ctl = sgimc->dma_ctrl;
+		if (ctl & 1) {
+			unsigned int pgsz = (ctl & 2) ? 14:12; /* 16k:4k */
+			/* PTEIndex is VPN-low (bits [22:14]/[20:12] ?) */
+			unsigned long pte = (lo >> 6) << 12; /* PTEBase */
+			pte += 8*((vaddr >> pgsz) & 0x1ff);
+			if (page_is_ram(PFN_DOWN(pte))) {
+				/*
+				 * Note: Since DMA hardware does look up
+				 * translation on its own, this PTE *must*
+				 * match the TLB/EntryLo-register format !
+				 */
+				unsigned long a = *(unsigned long *)
+						PHYS_TO_XKSEG_UNCACHED(pte);
+				a = (a & 0x3f) << 6; /* PFN */
+				a += vaddr & ((1 << pgsz) - 1);
+				return cpu_err_addr == a;
+			}
+		}
+	}
+	return 0;
+}
+
+static int check_vdma_memaddr(void)
+{
+	if (cpu_err_stat & CPU_ERRMASK) {
+		u32 a = sgimc->maddronly;
+
+		if (!(sgimc->dma_ctrl & 0x100)) /* Xlate-bit clear ? */
+			return cpu_err_addr == a;
+
+		if (check_microtlb(sgimc->dtlb_hi0, sgimc->dtlb_lo0, a) ||
+		    check_microtlb(sgimc->dtlb_hi1, sgimc->dtlb_lo1, a) ||
+		    check_microtlb(sgimc->dtlb_hi2, sgimc->dtlb_lo2, a) ||
+		    check_microtlb(sgimc->dtlb_hi3, sgimc->dtlb_lo3, a))
+			return 1;
+	}
+	return 0;
+}
+
+static int check_vdma_gioaddr(void)
+{
+	if (gio_err_stat & GIO_ERRMASK) {
+		u32 a = sgimc->gio_dma_trans;
+		a = (sgimc->gmaddronly & ~a) | (sgimc->gio_dma_sbits & a);
+		return gio_err_addr == a;
+	}
+	return 0;
+}
+
+/*
+ * MC sends an interrupt whenever bus or parity errors occur. In addition,
+ * if the error happened during a CPU read, it also asserts the bus error
+ * pin on the R4K. Code in bus error handler save the MC bus error registers
+ * and then clear the interrupt when this happens.
+ */
+
+static int ip28_be_interrupt(const struct pt_regs *regs)
+{
+	int i;
+
+	save_and_clear_buserr();
+	/*
+	 * Try to find out, whether we got here by a mispredicted speculative
+	 * load/store operation.  If so, it's not fatal, we can go on.
+	 */
+	/* Any cause other than "Interrupt" (ExcCode 0) is fatal. */
+	if (regs->cp0_cause & CAUSEF_EXCCODE)
+		goto mips_be_fatal;
+
+	/* Any cause other than "Bus error interrupt" (IP6) is weird. */
+	if ((regs->cp0_cause & CAUSEF_IP6) != CAUSEF_IP6)
+		goto mips_be_fatal;
+
+	if (extio_stat & (EXTIO_HPC3_BUSERR | EXTIO_EISA_BUSERR))
+		goto mips_be_fatal;
+
+	/* Any state other than "Memory bus error" is fatal. */
+	if (cpu_err_stat & CPU_ERRMASK & ~SGIMC_CSTAT_ADDR)
+		goto mips_be_fatal;
+
+	/* GIO errors other than timeouts are fatal */
+	if (gio_err_stat & GIO_ERRMASK & ~SGIMC_GSTAT_TIME)
+		goto mips_be_fatal;
+
+	/*
+	 * Now we have an asynchronous bus error, speculatively or DMA caused.
+	 * Need to search all DMA descriptors for the error address.
+	 */
+	for (i = 0; i < sizeof(hpc3)/sizeof(struct hpc3_stat); ++i) {
+		struct hpc3_stat *hp = (struct hpc3_stat *)&hpc3 + i;
+		if ((cpu_err_stat & CPU_ERRMASK) &&
+		    (cpu_err_addr == hp->ndptr || cpu_err_addr == hp->cbp))
+			break;
+		if ((gio_err_stat & GIO_ERRMASK) &&
+		    (gio_err_addr == hp->ndptr || gio_err_addr == hp->cbp))
+			break;
+	}
+	if (i < sizeof(hpc3)/sizeof(struct hpc3_stat)) {
+		struct hpc3_stat *hp = (struct hpc3_stat *)&hpc3 + i;
+		printk(KERN_ERR "at DMA addresses: HPC3 @ %08lx:"
+		       " ctl %08x, ndp %08x, cbp %08x\n",
+		       CPHYSADDR(hp->addr), hp->ctrl, hp->ndptr, hp->cbp);
+		goto mips_be_fatal;
+	}
+	/* Check MC's virtual DMA stuff. */
+	if (check_vdma_memaddr()) {
+		printk(KERN_ERR "at GIO DMA: mem address 0x%08x.\n",
+			sgimc->maddronly);
+		goto mips_be_fatal;
+	}
+	if (check_vdma_gioaddr()) {
+		printk(KERN_ERR "at GIO DMA: gio address 0x%08x.\n",
+			sgimc->gmaddronly);
+		goto mips_be_fatal;
+	}
+	/* A speculative bus error... */
+	if (debug_be_interrupt) {
+		print_buserr(regs);
+		printk(KERN_ERR "discarded!\n");
+	}
+	return MIPS_BE_DISCARD;
+
+mips_be_fatal:
+	print_buserr(regs);
+	return MIPS_BE_FATAL;
+}
+
+void ip22_be_interrupt(int irq)
+{
+	struct pt_regs *regs = get_irq_regs();
+
+	count_be_interrupt++;
+
+	if (ip28_be_interrupt(regs) != MIPS_BE_DISCARD) {
+		/* Assume it would be too dangerous to continue ... */
+		die_if_kernel("Oops", regs);
+		force_sig(SIGBUS);
+	} else if (debug_be_interrupt)
+		show_regs(regs);
+}
+
+static int ip28_be_handler(struct pt_regs *regs, int is_fixup)
+{
+	/*
+	 * We arrive here only in the unusual case of do_be() invocation,
+	 * i.e. by a bus error exception without a bus error interrupt.
+	 */
+	if (is_fixup) {
+		count_be_is_fixup++;
+		save_and_clear_buserr();
+		return MIPS_BE_FIXUP;
+	}
+	count_be_handler++;
+	return ip28_be_interrupt(regs);
+}
+
+void __init ip22_be_init(void)
+{
+	mips_set_be_handler(ip28_be_handler);
+}
+
+int ip28_show_be_info(struct seq_file *m)
+{
+	seq_printf(m, "IP28 be fixups\t\t: %u\n", count_be_is_fixup);
+	seq_printf(m, "IP28 be interrupts\t: %u\n", count_be_interrupt);
+	seq_printf(m, "IP28 be handler\t\t: %u\n", count_be_handler);
+
+	return 0;
+}
+
+static int __init debug_be_setup(char *str)
+{
+	debug_be_interrupt++;
+	return 1;
+}
+__setup("ip28_debug_be", debug_be_setup);
diff --git a/arch/mips/sgi-ip27/Kconfig b/arch/mips/sgi-ip27/Kconfig
new file mode 100644
index 000000000..e5b6cadbe
--- /dev/null
+++ b/arch/mips/sgi-ip27/Kconfig
@@ -0,0 +1,40 @@
+# SPDX-License-Identifier: GPL-2.0
+choice
+	prompt "Node addressing mode"
+	depends on SGI_IP27
+	default SGI_SN_M_MODE
+
+config SGI_SN_M_MODE
+	bool "IP27 M-Mode"
+	help
+	  The nodes of Origin, Onyx, Fuel and Tezro systems can be configured
+	  in either N-Modes which allows for more nodes or M-Mode which allows
+	  for more memory.  Your hardware is almost certainly running in
+	  M-Mode, so choose M-mode here.
+
+config SGI_SN_N_MODE
+	bool "IP27 N-Mode"
+	help
+	  The nodes of Origin, Onyx, Fuel and Tezro systems can be configured
+	  in either N-Modes which allows for more nodes or M-Mode which allows
+	  for more memory.  Your hardware is almost certainly running in
+	  M-Mode, so choose M-mode here.
+
+endchoice
+
+config MAPPED_KERNEL
+	bool "Mapped kernel support"
+	depends on SGI_IP27
+	help
+	  Change the way a Linux kernel is loaded into memory on a MIPS64
+	  machine.  This is required in order to support text replication on
+	  NUMA.  If you need to understand it, read the source code.
+
+config REPLICATE_KTEXT
+	bool "Kernel text replication support"
+	depends on SGI_IP27
+	select MAPPED_KERNEL
+	help
+	  Say Y here to enable replicating the kernel text across multiple
+	  nodes in a NUMA cluster.  This trades memory for speed.
+
diff --git a/arch/mips/sgi-ip27/Makefile b/arch/mips/sgi-ip27/Makefile
new file mode 100644
index 000000000..27c14ede1
--- /dev/null
+++ b/arch/mips/sgi-ip27/Makefile
@@ -0,0 +1,11 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Makefile for the IP27 specific kernel interface routines under Linux.
+#
+
+obj-y	:= ip27-berr.o ip27-irq.o ip27-init.o ip27-klconfig.o \
+	   ip27-klnuma.o ip27-memory.o ip27-nmi.o ip27-reset.o ip27-timer.o \
+	   ip27-hubio.o ip27-xtalk.o
+
+obj-$(CONFIG_EARLY_PRINTK)	+= ip27-console.o
+obj-$(CONFIG_SMP)		+= ip27-smp.o
diff --git a/arch/mips/sgi-ip27/Platform b/arch/mips/sgi-ip27/Platform
new file mode 100644
index 000000000..e734ee6ab
--- /dev/null
+++ b/arch/mips/sgi-ip27/Platform
@@ -0,0 +1,16 @@
+#
+# SGI-IP27 (Origin200/2000)
+#
+# Set the load address to >= 0xc000000000300000 if you want to leave space for
+# symmon, 0xc00000000001c000 for production kernels.  Note that the value must
+# be 16kb aligned or the handling of the current variable will break.
+#
+cflags-$(CONFIG_SGI_IP27)	+= -I$(srctree)/arch/mips/include/asm/mach-ip27
+ifdef CONFIG_MAPPED_KERNEL
+load-$(CONFIG_SGI_IP27)		+= 0xc00000004001c000
+OBJCOPYFLAGS			:= --change-addresses=0x3fffffff80000000
+dataoffset-$(CONFIG_SGI_IP27)	+= 0x01000000
+else
+load-$(CONFIG_SGI_IP27)		+= 0xa80000000001c000
+OBJCOPYFLAGS			:= --change-addresses=0x57ffffff80000000
+endif
diff --git a/arch/mips/sgi-ip27/ip27-berr.c b/arch/mips/sgi-ip27/ip27-berr.c
new file mode 100644
index 000000000..923a63a51
--- /dev/null
+++ b/arch/mips/sgi-ip27/ip27-berr.c
@@ -0,0 +1,96 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994, 1995, 1996, 1999, 2000 by Ralf Baechle
+ * Copyright (C) 1999, 2000 by Silicon Graphics
+ * Copyright (C) 2002  Maciej W. Rozycki
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/signal.h>	/* for SIGBUS */
+#include <linux/sched.h>	/* schow_regs(), force_sig() */
+#include <linux/sched/debug.h>
+#include <linux/sched/signal.h>
+
+#include <asm/ptrace.h>
+#include <asm/sn/addrs.h>
+#include <asm/sn/agent.h>
+#include <asm/sn/arch.h>
+#include <asm/tlbdebug.h>
+#include <asm/traps.h>
+#include <linux/uaccess.h>
+
+static void dump_hub_information(unsigned long errst0, unsigned long errst1)
+{
+	static char *err_type[2][8] = {
+		{ NULL, "Uncached Partial Read PRERR", "DERR", "Read Timeout",
+		  NULL, NULL, NULL, NULL },
+		{ "WERR", "Uncached Partial Write", "PWERR", "Write Timeout",
+		  NULL, NULL, NULL, NULL }
+	};
+	union pi_err_stat0 st0;
+	union pi_err_stat1 st1;
+
+	st0.pi_stat0_word = errst0;
+	st1.pi_stat1_word = errst1;
+
+	if (!st0.pi_stat0_fmt.s0_valid) {
+		pr_info("Hub does not contain valid error information\n");
+		return;
+	}
+
+	pr_info("Hub has valid error information:\n");
+	if (st0.pi_stat0_fmt.s0_ovr_run)
+		pr_info("Overrun is set. Error stack may contain additional "
+		       "information.\n");
+	pr_info("Hub error address is %08lx\n",
+		(unsigned long)st0.pi_stat0_fmt.s0_addr);
+	pr_info("Incoming message command 0x%lx\n",
+		(unsigned long)st0.pi_stat0_fmt.s0_cmd);
+	pr_info("Supplemental field of incoming message is 0x%lx\n",
+		(unsigned long)st0.pi_stat0_fmt.s0_supl);
+	pr_info("T5 Rn (for RRB only) is 0x%lx\n",
+		(unsigned long)st0.pi_stat0_fmt.s0_t5_req);
+	pr_info("Error type is %s\n", err_type[st1.pi_stat1_fmt.s1_rw_rb]
+	       [st0.pi_stat0_fmt.s0_err_type] ? : "invalid");
+}
+
+int ip27_be_handler(struct pt_regs *regs, int is_fixup)
+{
+	unsigned long errst0, errst1;
+	int data = regs->cp0_cause & 4;
+	int cpu = LOCAL_HUB_L(PI_CPU_NUM);
+
+	if (is_fixup)
+		return MIPS_BE_FIXUP;
+
+	printk("Slice %c got %cbe at 0x%lx\n", 'A' + cpu, data ? 'd' : 'i',
+	       regs->cp0_epc);
+	printk("Hub information:\n");
+	printk("ERR_INT_PEND = 0x%06llx\n", LOCAL_HUB_L(PI_ERR_INT_PEND));
+	errst0 = LOCAL_HUB_L(cpu ? PI_ERR_STATUS0_B : PI_ERR_STATUS0_A);
+	errst1 = LOCAL_HUB_L(cpu ? PI_ERR_STATUS1_B : PI_ERR_STATUS1_A);
+	dump_hub_information(errst0, errst1);
+	show_regs(regs);
+	dump_tlb_all();
+	while(1);
+	force_sig(SIGBUS);
+}
+
+void __init ip27_be_init(void)
+{
+	/* XXX Initialize all the Hub & Bridge error handling here.  */
+	int cpu = LOCAL_HUB_L(PI_CPU_NUM);
+	int cpuoff = cpu << 8;
+
+	mips_set_be_handler(ip27_be_handler);
+
+	LOCAL_HUB_S(PI_ERR_INT_PEND,
+		    cpu ? PI_ERR_CLEAR_ALL_B : PI_ERR_CLEAR_ALL_A);
+	LOCAL_HUB_S(PI_ERR_INT_MASK_A + cpuoff, 0);
+	LOCAL_HUB_S(PI_ERR_STACK_ADDR_A + cpuoff, 0);
+	LOCAL_HUB_S(PI_ERR_STACK_SIZE, 0);	/* Disable error stack */
+	LOCAL_HUB_S(PI_SYSAD_ERRCHK_EN, PI_SYSAD_CHECK_ALL);
+}
diff --git a/arch/mips/sgi-ip27/ip27-common.h b/arch/mips/sgi-ip27/ip27-common.h
new file mode 100644
index 000000000..ed008a084
--- /dev/null
+++ b/arch/mips/sgi-ip27/ip27-common.h
@@ -0,0 +1,20 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+#ifndef __IP27_COMMON_H
+#define __IP27_COMMON_H
+
+extern nasid_t master_nasid;
+
+extern void cpu_node_probe(void);
+extern void hub_rt_clock_event_init(void);
+extern void hub_rtc_init(nasid_t nasid);
+extern void install_cpu_nmi_handler(int slice);
+extern void install_ipi(void);
+extern void ip27_reboot_setup(void);
+extern const struct plat_smp_ops ip27_smp_ops;
+extern unsigned long node_getfirstfree(nasid_t nasid);
+extern void per_cpu_init(void);
+extern void replicate_kernel_text(void);
+extern void setup_replication_mask(void);
+
+#endif /* __IP27_COMMON_H */
diff --git a/arch/mips/sgi-ip27/ip27-console.c b/arch/mips/sgi-ip27/ip27-console.c
new file mode 100644
index 000000000..7737a88c6
--- /dev/null
+++ b/arch/mips/sgi-ip27/ip27-console.c
@@ -0,0 +1,42 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2001, 2002 Ralf Baechle
+ */
+
+#include <asm/page.h>
+#include <asm/setup.h>
+#include <asm/sn/addrs.h>
+#include <asm/sn/agent.h>
+#include <asm/sn/klconfig.h>
+#include <asm/sn/ioc3.h>
+
+#include <linux/serial.h>
+#include <linux/serial_core.h>
+
+#include "ip27-common.h"
+
+#define IOC3_CLK	(22000000 / 3)
+#define IOC3_FLAGS	(0)
+
+static inline struct ioc3_uartregs *console_uart(void)
+{
+	struct ioc3 *ioc3;
+	nasid_t nasid;
+
+	nasid = (master_nasid == INVALID_NASID) ? get_nasid() : master_nasid;
+	ioc3 = (struct ioc3 *)KL_CONFIG_CH_CONS_INFO(nasid)->memory_base;
+
+	return &ioc3->sregs.uarta;
+}
+
+void prom_putchar(char c)
+{
+	struct ioc3_uartregs *uart = console_uart();
+
+	while ((readb(&uart->iu_lsr) & 0x20) == 0)
+		;
+	writeb(c, &uart->iu_thr);
+}
diff --git a/arch/mips/sgi-ip27/ip27-hubio.c b/arch/mips/sgi-ip27/ip27-hubio.c
new file mode 100644
index 000000000..8352eb640
--- /dev/null
+++ b/arch/mips/sgi-ip27/ip27-hubio.c
@@ -0,0 +1,185 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 1992-1997, 2000-2003 Silicon Graphics, Inc.
+ * Copyright (C) 2004 Christoph Hellwig.
+ *
+ * Support functions for the HUB ASIC - mostly PIO mapping related.
+ */
+
+#include <linux/bitops.h>
+#include <linux/string.h>
+#include <linux/mmzone.h>
+#include <asm/sn/addrs.h>
+#include <asm/sn/arch.h>
+#include <asm/sn/agent.h>
+#include <asm/sn/io.h>
+#include <asm/xtalk/xtalk.h>
+
+
+static int force_fire_and_forget = 1;
+
+/**
+ * hub_pio_map	-  establish a HUB PIO mapping
+ *
+ * @hub:	hub to perform PIO mapping on
+ * @widget:	widget ID to perform PIO mapping for
+ * @xtalk_addr: xtalk_address that needs to be mapped
+ * @size:	size of the PIO mapping
+ *
+ **/
+unsigned long hub_pio_map(nasid_t nasid, xwidgetnum_t widget,
+			  unsigned long xtalk_addr, size_t size)
+{
+	unsigned i;
+
+	/* use small-window mapping if possible */
+	if ((xtalk_addr % SWIN_SIZE) + size <= SWIN_SIZE)
+		return NODE_SWIN_BASE(nasid, widget) + (xtalk_addr % SWIN_SIZE);
+
+	if ((xtalk_addr % BWIN_SIZE) + size > BWIN_SIZE) {
+		printk(KERN_WARNING "PIO mapping at hub %d widget %d addr 0x%lx"
+				" too big (%ld)\n",
+				nasid, widget, xtalk_addr, size);
+		return 0;
+	}
+
+	xtalk_addr &= ~(BWIN_SIZE-1);
+	for (i = 0; i < HUB_NUM_BIG_WINDOW; i++) {
+		if (test_and_set_bit(i, hub_data(nasid)->h_bigwin_used))
+			continue;
+
+		/*
+		 * The code below does a PIO write to setup an ITTE entry.
+		 *
+		 * We need to prevent other CPUs from seeing our updated
+		 * memory shadow of the ITTE (in the piomap) until the ITTE
+		 * entry is actually set up; otherwise, another CPU might
+		 * attempt a PIO prematurely.
+		 *
+		 * Also, the only way we can know that an entry has been
+		 * received  by the hub and can be used by future PIO reads/
+		 * writes is by reading back the ITTE entry after writing it.
+		 *
+		 * For these two reasons, we PIO read back the ITTE entry
+		 * after we write it.
+		 */
+		IIO_ITTE_PUT(nasid, i, HUB_PIO_MAP_TO_MEM, widget, xtalk_addr);
+		__raw_readq(IIO_ITTE_GET(nasid, i));
+
+		return NODE_BWIN_BASE(nasid, widget) + (xtalk_addr % BWIN_SIZE);
+	}
+
+	printk(KERN_WARNING "unable to establish PIO mapping for at"
+			" hub %d widget %d addr 0x%lx\n",
+			nasid, widget, xtalk_addr);
+	return 0;
+}
+
+
+/*
+ * hub_setup_prb(nasid, prbnum, credits, conveyor)
+ *
+ *	Put a PRB into fire-and-forget mode if conveyor isn't set.  Otherwise,
+ *	put it into conveyor belt mode with the specified number of credits.
+ */
+static void hub_setup_prb(nasid_t nasid, int prbnum, int credits)
+{
+	union iprb_u prb;
+	int prb_offset;
+
+	/*
+	 * Get the current register value.
+	 */
+	prb_offset = IIO_IOPRB(prbnum);
+	prb.iprb_regval = REMOTE_HUB_L(nasid, prb_offset);
+
+	/*
+	 * Clear out some fields.
+	 */
+	prb.iprb_ovflow = 1;
+	prb.iprb_bnakctr = 0;
+	prb.iprb_anakctr = 0;
+
+	/*
+	 * Enable or disable fire-and-forget mode.
+	 */
+	prb.iprb_ff = force_fire_and_forget ? 1 : 0;
+
+	/*
+	 * Set the appropriate number of PIO credits for the widget.
+	 */
+	prb.iprb_xtalkctr = credits;
+
+	/*
+	 * Store the new value to the register.
+	 */
+	REMOTE_HUB_S(nasid, prb_offset, prb.iprb_regval);
+}
+
+/**
+ * hub_set_piomode  -  set pio mode for a given hub
+ *
+ * @nasid:	physical node ID for the hub in question
+ *
+ * Put the hub into either "PIO conveyor belt" mode or "fire-and-forget" mode.
+ * To do this, we have to make absolutely sure that no PIOs are in progress
+ * so we turn off access to all widgets for the duration of the function.
+ *
+ * XXX - This code should really check what kind of widget we're talking
+ * to.	Bridges can only handle three requests, but XG will do more.
+ * How many can crossbow handle to widget 0?  We're assuming 1.
+ *
+ * XXX - There is a bug in the crossbow that link reset PIOs do not
+ * return write responses.  The easiest solution to this problem is to
+ * leave widget 0 (xbow) in fire-and-forget mode at all times.	This
+ * only affects pio's to xbow registers, which should be rare.
+ **/
+static void hub_set_piomode(nasid_t nasid)
+{
+	u64 ii_iowa;
+	union hubii_wcr_u ii_wcr;
+	unsigned i;
+
+	ii_iowa = REMOTE_HUB_L(nasid, IIO_OUTWIDGET_ACCESS);
+	REMOTE_HUB_S(nasid, IIO_OUTWIDGET_ACCESS, 0);
+
+	ii_wcr.wcr_reg_value = REMOTE_HUB_L(nasid, IIO_WCR);
+
+	if (ii_wcr.iwcr_dir_con) {
+		/*
+		 * Assume a bridge here.
+		 */
+		hub_setup_prb(nasid, 0, 3);
+	} else {
+		/*
+		 * Assume a crossbow here.
+		 */
+		hub_setup_prb(nasid, 0, 1);
+	}
+
+	/*
+	 * XXX - Here's where we should take the widget type into
+	 * when account assigning credits.
+	 */
+	for (i = HUB_WIDGET_ID_MIN; i <= HUB_WIDGET_ID_MAX; i++)
+		hub_setup_prb(nasid, i, 3);
+
+	REMOTE_HUB_S(nasid, IIO_OUTWIDGET_ACCESS, ii_iowa);
+}
+
+/*
+ * hub_pio_init	 -  PIO-related hub initialization
+ *
+ * @hub:	hubinfo structure for our hub
+ */
+void hub_pio_init(nasid_t nasid)
+{
+	unsigned i;
+
+	/* initialize big window piomaps for this hub */
+	bitmap_zero(hub_data(nasid)->h_bigwin_used, HUB_NUM_BIG_WINDOW);
+	for (i = 0; i < HUB_NUM_BIG_WINDOW; i++)
+		IIO_ITTE_DISABLE(nasid, i);
+
+	hub_set_piomode(nasid);
+}
diff --git a/arch/mips/sgi-ip27/ip27-init.c b/arch/mips/sgi-ip27/ip27-init.c
new file mode 100644
index 000000000..a4daf8ccd
--- /dev/null
+++ b/arch/mips/sgi-ip27/ip27-init.c
@@ -0,0 +1,147 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General
+ * Public License.  See the file "COPYING" in the main directory of this
+ * archive for more details.
+ *
+ * Copyright (C) 2000 - 2001 by Kanoj Sarcar (kanoj@sgi.com)
+ * Copyright (C) 2000 - 2001 by Silicon Graphics, Inc.
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/sched.h>
+#include <linux/smp.h>
+#include <linux/mm.h>
+#include <linux/export.h>
+#include <linux/cpumask.h>
+#include <asm/bootinfo.h>
+#include <asm/cpu.h>
+#include <asm/io.h>
+#include <asm/sgialib.h>
+#include <asm/time.h>
+#include <asm/sn/agent.h>
+#include <asm/sn/types.h>
+#include <asm/sn/klconfig.h>
+#include <asm/sn/ioc3.h>
+#include <asm/mipsregs.h>
+#include <asm/sn/gda.h>
+#include <asm/sn/intr.h>
+#include <asm/current.h>
+#include <asm/processor.h>
+#include <asm/mmu_context.h>
+#include <asm/thread_info.h>
+#include <asm/sn/launch.h>
+#include <asm/sn/mapped_kernel.h>
+
+#include "ip27-common.h"
+
+#define CPU_NONE		(cpuid_t)-1
+
+static DECLARE_BITMAP(hub_init_mask, MAX_NUMNODES);
+nasid_t master_nasid = INVALID_NASID;
+
+struct cpuinfo_ip27 sn_cpu_info[NR_CPUS];
+EXPORT_SYMBOL_GPL(sn_cpu_info);
+
+static void per_hub_init(nasid_t nasid)
+{
+	struct hub_data *hub = hub_data(nasid);
+
+	cpumask_set_cpu(smp_processor_id(), &hub->h_cpus);
+
+	if (test_and_set_bit(nasid, hub_init_mask))
+		return;
+	/*
+	 * Set CRB timeout at 5ms, (< PI timeout of 10ms)
+	 */
+	REMOTE_HUB_S(nasid, IIO_ICTP, 0x800);
+	REMOTE_HUB_S(nasid, IIO_ICTO, 0xff);
+
+	hub_rtc_init(nasid);
+
+	if (nasid) {
+		/* copy exception handlers from first node to current node */
+		memcpy((void *)NODE_OFFSET_TO_K0(nasid, 0),
+		       (void *)CKSEG0, 0x200);
+		__flush_cache_all();
+		/* switch to node local exception handlers */
+		REMOTE_HUB_S(nasid, PI_CALIAS_SIZE, PI_CALIAS_SIZE_8K);
+	}
+}
+
+void per_cpu_init(void)
+{
+	int cpu = smp_processor_id();
+	nasid_t nasid = get_nasid();
+
+	clear_c0_status(ST0_IM);
+
+	per_hub_init(nasid);
+
+	pr_info("CPU %d clock is %dMHz.\n", cpu, sn_cpu_info[cpu].p_speed);
+
+	install_ipi();
+
+	/* Install our NMI handler if symmon hasn't installed one. */
+	install_cpu_nmi_handler(cputoslice(cpu));
+
+	enable_percpu_irq(IP27_HUB_PEND0_IRQ, IRQ_TYPE_NONE);
+	enable_percpu_irq(IP27_HUB_PEND1_IRQ, IRQ_TYPE_NONE);
+}
+
+void __init plat_mem_setup(void)
+{
+	u64 p, e, n_mode;
+	nasid_t nid;
+
+	register_smp_ops(&ip27_smp_ops);
+
+	ip27_reboot_setup();
+
+	/*
+	 * hub_rtc init and cpu clock intr enabled for later calibrate_delay.
+	 */
+	nid = get_nasid();
+	printk("IP27: Running on node %d.\n", nid);
+
+	p = LOCAL_HUB_L(PI_CPU_PRESENT_A) & 1;
+	e = LOCAL_HUB_L(PI_CPU_ENABLE_A) & 1;
+	printk("Node %d has %s primary CPU%s.\n", nid,
+	       p ? "a" : "no",
+	       e ? ", CPU is running" : "");
+
+	p = LOCAL_HUB_L(PI_CPU_PRESENT_B) & 1;
+	e = LOCAL_HUB_L(PI_CPU_ENABLE_B) & 1;
+	printk("Node %d has %s secondary CPU%s.\n", nid,
+	       p ? "a" : "no",
+	       e ? ", CPU is running" : "");
+
+	/*
+	 * Try to catch kernel missconfigurations and give user an
+	 * indication what option to select.
+	 */
+	n_mode = LOCAL_HUB_L(NI_STATUS_REV_ID) & NSRI_MORENODES_MASK;
+	printk("Machine is in %c mode.\n", n_mode ? 'N' : 'M');
+#ifdef CONFIG_SGI_SN_N_MODE
+	if (!n_mode)
+		panic("Kernel compiled for M mode.");
+#else
+	if (n_mode)
+		panic("Kernel compiled for N mode.");
+#endif
+
+	ioport_resource.start = 0;
+	ioport_resource.end = ~0UL;
+	set_io_port_base(IO_BASE);
+}
+
+const char *get_system_type(void)
+{
+	return "SGI Origin";
+}
+
+void __init prom_init(void)
+{
+	prom_init_cmdline(fw_arg0, (LONG *)fw_arg1);
+	prom_meminit();
+}
+
diff --git a/arch/mips/sgi-ip27/ip27-irq.c b/arch/mips/sgi-ip27/ip27-irq.c
new file mode 100644
index 000000000..a0dd3bd2b
--- /dev/null
+++ b/arch/mips/sgi-ip27/ip27-irq.c
@@ -0,0 +1,311 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ip27-irq.c: Highlevel interrupt handling for IP27 architecture.
+ *
+ * Copyright (C) 1999, 2000 Ralf Baechle (ralf@gnu.org)
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ * Copyright (C) 1999 - 2001 Kanoj Sarcar
+ */
+
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/ioport.h>
+#include <linux/kernel.h>
+#include <linux/bitops.h>
+#include <linux/sched.h>
+
+#include <asm/io.h>
+#include <asm/irq_cpu.h>
+#include <asm/sn/addrs.h>
+#include <asm/sn/agent.h>
+#include <asm/sn/arch.h>
+#include <asm/sn/intr.h>
+#include <asm/sn/irq_alloc.h>
+
+struct hub_irq_data {
+	u64	*irq_mask[2];
+	cpuid_t	cpu;
+};
+
+static DECLARE_BITMAP(hub_irq_map, IP27_HUB_IRQ_COUNT);
+
+static DEFINE_PER_CPU(unsigned long [2], irq_enable_mask);
+
+static inline int alloc_level(void)
+{
+	int level;
+
+again:
+	level = find_first_zero_bit(hub_irq_map, IP27_HUB_IRQ_COUNT);
+	if (level >= IP27_HUB_IRQ_COUNT)
+		return -ENOSPC;
+
+	if (test_and_set_bit(level, hub_irq_map))
+		goto again;
+
+	return level;
+}
+
+static void enable_hub_irq(struct irq_data *d)
+{
+	struct hub_irq_data *hd = irq_data_get_irq_chip_data(d);
+	unsigned long *mask = per_cpu(irq_enable_mask, hd->cpu);
+
+	set_bit(d->hwirq, mask);
+	__raw_writeq(mask[0], hd->irq_mask[0]);
+	__raw_writeq(mask[1], hd->irq_mask[1]);
+}
+
+static void disable_hub_irq(struct irq_data *d)
+{
+	struct hub_irq_data *hd = irq_data_get_irq_chip_data(d);
+	unsigned long *mask = per_cpu(irq_enable_mask, hd->cpu);
+
+	clear_bit(d->hwirq, mask);
+	__raw_writeq(mask[0], hd->irq_mask[0]);
+	__raw_writeq(mask[1], hd->irq_mask[1]);
+}
+
+static void setup_hub_mask(struct hub_irq_data *hd, const struct cpumask *mask)
+{
+	nasid_t nasid;
+	int cpu;
+
+	cpu = cpumask_first_and(mask, cpu_online_mask);
+	if (cpu >= nr_cpu_ids)
+		cpu = cpumask_any(cpu_online_mask);
+
+	nasid = cpu_to_node(cpu);
+	hd->cpu = cpu;
+	if (!cputoslice(cpu)) {
+		hd->irq_mask[0] = REMOTE_HUB_PTR(nasid, PI_INT_MASK0_A);
+		hd->irq_mask[1] = REMOTE_HUB_PTR(nasid, PI_INT_MASK1_A);
+	} else {
+		hd->irq_mask[0] = REMOTE_HUB_PTR(nasid, PI_INT_MASK0_B);
+		hd->irq_mask[1] = REMOTE_HUB_PTR(nasid, PI_INT_MASK1_B);
+	}
+}
+
+static int set_affinity_hub_irq(struct irq_data *d, const struct cpumask *mask,
+				bool force)
+{
+	struct hub_irq_data *hd = irq_data_get_irq_chip_data(d);
+
+	if (!hd)
+		return -EINVAL;
+
+	if (irqd_is_started(d))
+		disable_hub_irq(d);
+
+	setup_hub_mask(hd, mask);
+
+	if (irqd_is_started(d))
+		enable_hub_irq(d);
+
+	irq_data_update_effective_affinity(d, cpumask_of(hd->cpu));
+
+	return 0;
+}
+
+static struct irq_chip hub_irq_type = {
+	.name		  = "HUB",
+	.irq_mask	  = disable_hub_irq,
+	.irq_unmask	  = enable_hub_irq,
+	.irq_set_affinity = set_affinity_hub_irq,
+};
+
+static int hub_domain_alloc(struct irq_domain *domain, unsigned int virq,
+			    unsigned int nr_irqs, void *arg)
+{
+	struct irq_alloc_info *info = arg;
+	struct hub_irq_data *hd;
+	struct hub_data *hub;
+	struct irq_desc *desc;
+	int swlevel;
+
+	if (nr_irqs > 1 || !info)
+		return -EINVAL;
+
+	hd = kzalloc(sizeof(*hd), GFP_KERNEL);
+	if (!hd)
+		return -ENOMEM;
+
+	swlevel = alloc_level();
+	if (unlikely(swlevel < 0)) {
+		kfree(hd);
+		return -EAGAIN;
+	}
+	irq_domain_set_info(domain, virq, swlevel, &hub_irq_type, hd,
+			    handle_level_irq, NULL, NULL);
+
+	/* use CPU connected to nearest hub */
+	hub = hub_data(info->nasid);
+	setup_hub_mask(hd, &hub->h_cpus);
+	info->nasid = cpu_to_node(hd->cpu);
+
+	/* Make sure it's not already pending when we connect it. */
+	REMOTE_HUB_CLR_INTR(info->nasid, swlevel);
+
+	desc = irq_to_desc(virq);
+	desc->irq_common_data.node = info->nasid;
+	cpumask_copy(desc->irq_common_data.affinity, &hub->h_cpus);
+
+	return 0;
+}
+
+static void hub_domain_free(struct irq_domain *domain,
+			    unsigned int virq, unsigned int nr_irqs)
+{
+	struct irq_data *irqd;
+
+	if (nr_irqs > 1)
+		return;
+
+	irqd = irq_domain_get_irq_data(domain, virq);
+	if (irqd && irqd->chip_data)
+		kfree(irqd->chip_data);
+}
+
+static const struct irq_domain_ops hub_domain_ops = {
+	.alloc = hub_domain_alloc,
+	.free  = hub_domain_free,
+};
+
+/*
+ * This code is unnecessarily complex, because we do
+ * intr enabling. Basically, once we grab the set of intrs we need
+ * to service, we must mask _all_ these interrupts; firstly, to make
+ * sure the same intr does not intr again, causing recursion that
+ * can lead to stack overflow. Secondly, we can not just mask the
+ * one intr we are do_IRQing, because the non-masked intrs in the
+ * first set might intr again, causing multiple servicings of the
+ * same intr. This effect is mostly seen for intercpu intrs.
+ * Kanoj 05.13.00
+ */
+
+static void ip27_do_irq_mask0(struct irq_desc *desc)
+{
+	cpuid_t cpu = smp_processor_id();
+	unsigned long *mask = per_cpu(irq_enable_mask, cpu);
+	struct irq_domain *domain;
+	u64 pend0;
+	int ret;
+
+	/* copied from Irix intpend0() */
+	pend0 = LOCAL_HUB_L(PI_INT_PEND0);
+
+	pend0 &= mask[0];		/* Pick intrs we should look at */
+	if (!pend0)
+		return;
+
+#ifdef CONFIG_SMP
+	if (pend0 & (1UL << CPU_RESCHED_A_IRQ)) {
+		LOCAL_HUB_CLR_INTR(CPU_RESCHED_A_IRQ);
+		scheduler_ipi();
+	} else if (pend0 & (1UL << CPU_RESCHED_B_IRQ)) {
+		LOCAL_HUB_CLR_INTR(CPU_RESCHED_B_IRQ);
+		scheduler_ipi();
+	} else if (pend0 & (1UL << CPU_CALL_A_IRQ)) {
+		LOCAL_HUB_CLR_INTR(CPU_CALL_A_IRQ);
+		generic_smp_call_function_interrupt();
+	} else if (pend0 & (1UL << CPU_CALL_B_IRQ)) {
+		LOCAL_HUB_CLR_INTR(CPU_CALL_B_IRQ);
+		generic_smp_call_function_interrupt();
+	} else
+#endif
+	{
+		domain = irq_desc_get_handler_data(desc);
+		ret = generic_handle_domain_irq(domain, __ffs(pend0));
+		if (ret)
+			spurious_interrupt();
+	}
+
+	LOCAL_HUB_L(PI_INT_PEND0);
+}
+
+static void ip27_do_irq_mask1(struct irq_desc *desc)
+{
+	cpuid_t cpu = smp_processor_id();
+	unsigned long *mask = per_cpu(irq_enable_mask, cpu);
+	struct irq_domain *domain;
+	u64 pend1;
+	int ret;
+
+	/* copied from Irix intpend0() */
+	pend1 = LOCAL_HUB_L(PI_INT_PEND1);
+
+	pend1 &= mask[1];		/* Pick intrs we should look at */
+	if (!pend1)
+		return;
+
+	domain = irq_desc_get_handler_data(desc);
+	ret = generic_handle_domain_irq(domain, __ffs(pend1) + 64);
+	if (ret)
+		spurious_interrupt();
+
+	LOCAL_HUB_L(PI_INT_PEND1);
+}
+
+void install_ipi(void)
+{
+	int cpu = smp_processor_id();
+	unsigned long *mask = per_cpu(irq_enable_mask, cpu);
+	int slice = LOCAL_HUB_L(PI_CPU_NUM);
+	int resched, call;
+
+	resched = CPU_RESCHED_A_IRQ + slice;
+	set_bit(resched, mask);
+	LOCAL_HUB_CLR_INTR(resched);
+
+	call = CPU_CALL_A_IRQ + slice;
+	set_bit(call, mask);
+	LOCAL_HUB_CLR_INTR(call);
+
+	if (slice == 0) {
+		LOCAL_HUB_S(PI_INT_MASK0_A, mask[0]);
+		LOCAL_HUB_S(PI_INT_MASK1_A, mask[1]);
+	} else {
+		LOCAL_HUB_S(PI_INT_MASK0_B, mask[0]);
+		LOCAL_HUB_S(PI_INT_MASK1_B, mask[1]);
+	}
+}
+
+void __init arch_init_irq(void)
+{
+	struct irq_domain *domain;
+	struct fwnode_handle *fn;
+	int i;
+
+	mips_cpu_irq_init();
+
+	/*
+	 * Some interrupts are reserved by hardware or by software convention.
+	 * Mark these as reserved right away so they won't be used accidentally
+	 * later.
+	 */
+	for (i = 0; i <= CPU_CALL_B_IRQ; i++)
+		set_bit(i, hub_irq_map);
+
+	for (i = NI_BRDCAST_ERR_A; i <= MSC_PANIC_INTR; i++)
+		set_bit(i, hub_irq_map);
+
+	fn = irq_domain_alloc_named_fwnode("HUB");
+	WARN_ON(fn == NULL);
+	if (!fn)
+		return;
+	domain = irq_domain_create_linear(fn, IP27_HUB_IRQ_COUNT,
+					  &hub_domain_ops, NULL);
+	WARN_ON(domain == NULL);
+	if (!domain)
+		return;
+
+	irq_set_default_host(domain);
+
+	irq_set_percpu_devid(IP27_HUB_PEND0_IRQ);
+	irq_set_chained_handler_and_data(IP27_HUB_PEND0_IRQ, ip27_do_irq_mask0,
+					 domain);
+	irq_set_percpu_devid(IP27_HUB_PEND1_IRQ);
+	irq_set_chained_handler_and_data(IP27_HUB_PEND1_IRQ, ip27_do_irq_mask1,
+					 domain);
+}
diff --git a/arch/mips/sgi-ip27/ip27-klconfig.c b/arch/mips/sgi-ip27/ip27-klconfig.c
new file mode 100644
index 000000000..81a1646e6
--- /dev/null
+++ b/arch/mips/sgi-ip27/ip27-klconfig.c
@@ -0,0 +1,74 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 1999, 2000 Ralf Baechle (ralf@gnu.org)
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ */
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/interrupt.h>
+#include <linux/kernel_stat.h>
+#include <linux/param.h>
+#include <linux/timex.h>
+#include <linux/mm.h>
+
+#include <asm/sn/klconfig.h>
+#include <asm/sn/arch.h>
+#include <asm/sn/gda.h>
+
+klinfo_t *find_component(lboard_t *brd, klinfo_t *kli, unsigned char struct_type)
+{
+	int index, j;
+
+	if (kli == (klinfo_t *)NULL) {
+		index = 0;
+	} else {
+		for (j = 0; j < KLCF_NUM_COMPS(brd); j++)
+			if (kli == KLCF_COMP(brd, j))
+				break;
+		index = j;
+		if (index == KLCF_NUM_COMPS(brd)) {
+			printk("find_component: Bad pointer: 0x%p\n", kli);
+			return (klinfo_t *)NULL;
+		}
+		index++;		/* next component */
+	}
+
+	for (; index < KLCF_NUM_COMPS(brd); index++) {
+		kli = KLCF_COMP(brd, index);
+		if (KLCF_COMP_TYPE(kli) == struct_type)
+			return kli;
+	}
+
+	/* Didn't find it. */
+	return (klinfo_t *)NULL;
+}
+
+klinfo_t *find_first_component(lboard_t *brd, unsigned char struct_type)
+{
+	return find_component(brd, (klinfo_t *)NULL, struct_type);
+}
+
+lboard_t *find_lboard(lboard_t *start, unsigned char brd_type)
+{
+	/* Search all boards stored on this node. */
+	while (start) {
+		if (start->brd_type == brd_type)
+			return start;
+		start = KLCF_NEXT(start);
+	}
+	/* Didn't find it. */
+	return (lboard_t *)NULL;
+}
+
+lboard_t *find_lboard_class(lboard_t *start, unsigned char brd_type)
+{
+	/* Search all boards stored on this node. */
+	while (start) {
+		if (KLCLASS(start->brd_type) == KLCLASS(brd_type))
+			return start;
+		start = KLCF_NEXT(start);
+	}
+
+	/* Didn't find it. */
+	return (lboard_t *)NULL;
+}
diff --git a/arch/mips/sgi-ip27/ip27-klnuma.c b/arch/mips/sgi-ip27/ip27-klnuma.c
new file mode 100644
index 000000000..abd7a84df
--- /dev/null
+++ b/arch/mips/sgi-ip27/ip27-klnuma.c
@@ -0,0 +1,129 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Ported from IRIX to Linux by Kanoj Sarcar, 06/08/00.
+ * Copyright 2000 - 2001 Silicon Graphics, Inc.
+ * Copyright 2000 - 2001 Kanoj Sarcar (kanoj@sgi.com)
+ */
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/mmzone.h>
+#include <linux/kernel.h>
+#include <linux/nodemask.h>
+#include <linux/string.h>
+
+#include <asm/page.h>
+#include <asm/sections.h>
+#include <asm/sn/types.h>
+#include <asm/sn/arch.h>
+#include <asm/sn/gda.h>
+#include <asm/sn/mapped_kernel.h>
+
+#include "ip27-common.h"
+
+static nodemask_t ktext_repmask;
+
+/*
+ * XXX - This needs to be much smarter about where it puts copies of the
+ * kernel.  For example, we should never put a copy on a headless node,
+ * and we should respect the topology of the machine.
+ */
+void __init setup_replication_mask(void)
+{
+	/* Set only the master cnode's bit.  The master cnode is always 0. */
+	nodes_clear(ktext_repmask);
+	node_set(0, ktext_repmask);
+
+#ifdef CONFIG_REPLICATE_KTEXT
+#ifndef CONFIG_MAPPED_KERNEL
+#error Kernel replication works with mapped kernel support. No calias support.
+#endif
+	{
+		nasid_t nasid;
+
+		for_each_online_node(nasid) {
+			if (nasid == 0)
+				continue;
+			/* Advertise that we have a copy of the kernel */
+			node_set(nasid, ktext_repmask);
+		}
+	}
+#endif
+	/* Set up a GDA pointer to the replication mask. */
+	GDA->g_ktext_repmask = &ktext_repmask;
+}
+
+
+static __init void set_ktext_source(nasid_t client_nasid, nasid_t server_nasid)
+{
+	kern_vars_t *kvp;
+
+	kvp = &hub_data(client_nasid)->kern_vars;
+
+	KERN_VARS_ADDR(client_nasid) = (unsigned long)kvp;
+
+	kvp->kv_magic = KV_MAGIC;
+	kvp->kv_ro_nasid = server_nasid;
+	kvp->kv_rw_nasid = master_nasid;
+	kvp->kv_ro_baseaddr = NODE_CAC_BASE(server_nasid);
+	kvp->kv_rw_baseaddr = NODE_CAC_BASE(master_nasid);
+	printk("REPLICATION: ON nasid %d, ktext from nasid %d, kdata from nasid %d\n", client_nasid, server_nasid, master_nasid);
+}
+
+/* XXX - When the BTE works, we should use it instead of this. */
+static __init void copy_kernel(nasid_t dest_nasid)
+{
+	unsigned long dest_kern_start, source_start, source_end, kern_size;
+
+	source_start = (unsigned long) _stext;
+	source_end = (unsigned long) _etext;
+	kern_size = source_end - source_start;
+
+	dest_kern_start = CHANGE_ADDR_NASID(MAPPED_KERN_RO_TO_K0(source_start),
+					    dest_nasid);
+	memcpy((void *)dest_kern_start, (void *)source_start, kern_size);
+}
+
+void __init replicate_kernel_text(void)
+{
+	nasid_t client_nasid;
+	nasid_t server_nasid;
+
+	server_nasid = master_nasid;
+
+	/* Record where the master node should get its kernel text */
+	set_ktext_source(master_nasid, master_nasid);
+
+	for_each_online_node(client_nasid) {
+		if (client_nasid == 0)
+			continue;
+
+		/* Check if this node should get a copy of the kernel */
+		if (node_isset(client_nasid, ktext_repmask)) {
+			server_nasid = client_nasid;
+			copy_kernel(server_nasid);
+		}
+
+		/* Record where this node should get its kernel text */
+		set_ktext_source(client_nasid, server_nasid);
+	}
+}
+
+/*
+ * Return pfn of first free page of memory on a node. PROM may allocate
+ * data structures on the first couple of pages of the first slot of each
+ * node. If this is the case, getfirstfree(node) > getslotstart(node, 0).
+ */
+unsigned long node_getfirstfree(nasid_t nasid)
+{
+	unsigned long loadbase = REP_BASE;
+	unsigned long offset;
+
+#ifdef CONFIG_MAPPED_KERNEL
+	loadbase += 16777216;
+#endif
+	offset = PAGE_ALIGN((unsigned long)(&_end)) - loadbase;
+	if ((nasid == 0) || (node_isset(nasid, ktext_repmask)))
+		return TO_NODE(nasid, offset) >> PAGE_SHIFT;
+	else
+		return KDM_TO_PHYS(PAGE_ALIGN(SYMMON_STK_ADDR(nasid, 0))) >> PAGE_SHIFT;
+}
diff --git a/arch/mips/sgi-ip27/ip27-memory.c b/arch/mips/sgi-ip27/ip27-memory.c
new file mode 100644
index 000000000..f79c48393
--- /dev/null
+++ b/arch/mips/sgi-ip27/ip27-memory.c
@@ -0,0 +1,434 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2000, 05 by Ralf Baechle (ralf@linux-mips.org)
+ * Copyright (C) 2000 by Silicon Graphics, Inc.
+ * Copyright (C) 2004 by Christoph Hellwig
+ *
+ * On SGI IP27 the ARC memory configuration data is completely bogus but
+ * alternate easier to use mechanisms are available.
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/memblock.h>
+#include <linux/mm.h>
+#include <linux/mmzone.h>
+#include <linux/export.h>
+#include <linux/nodemask.h>
+#include <linux/swap.h>
+#include <linux/pfn.h>
+#include <linux/highmem.h>
+#include <asm/page.h>
+#include <asm/pgalloc.h>
+#include <asm/sections.h>
+
+#include <asm/sn/arch.h>
+#include <asm/sn/agent.h>
+#include <asm/sn/klconfig.h>
+
+#include "ip27-common.h"
+
+#define SLOT_PFNSHIFT		(SLOT_SHIFT - PAGE_SHIFT)
+#define PFN_NASIDSHFT		(NASID_SHFT - PAGE_SHIFT)
+
+struct node_data *__node_data[MAX_NUMNODES];
+
+EXPORT_SYMBOL(__node_data);
+
+static u64 gen_region_mask(void)
+{
+	int region_shift;
+	u64 region_mask;
+	nasid_t nasid;
+
+	region_shift = get_region_shift();
+	region_mask = 0;
+	for_each_online_node(nasid)
+		region_mask |= BIT_ULL(nasid >> region_shift);
+
+	return region_mask;
+}
+
+#define rou_rflag	rou_flags
+
+static int router_distance;
+
+static void router_recurse(klrou_t *router_a, klrou_t *router_b, int depth)
+{
+	klrou_t *router;
+	lboard_t *brd;
+	int	port;
+
+	if (router_a->rou_rflag == 1)
+		return;
+
+	if (depth >= router_distance)
+		return;
+
+	router_a->rou_rflag = 1;
+
+	for (port = 1; port <= MAX_ROUTER_PORTS; port++) {
+		if (router_a->rou_port[port].port_nasid == INVALID_NASID)
+			continue;
+
+		brd = (lboard_t *)NODE_OFFSET_TO_K0(
+			router_a->rou_port[port].port_nasid,
+			router_a->rou_port[port].port_offset);
+
+		if (brd->brd_type == KLTYPE_ROUTER) {
+			router = (klrou_t *)NODE_OFFSET_TO_K0(NASID_GET(brd), brd->brd_compts[0]);
+			if (router == router_b) {
+				if (depth < router_distance)
+					router_distance = depth;
+			}
+			else
+				router_recurse(router, router_b, depth + 1);
+		}
+	}
+
+	router_a->rou_rflag = 0;
+}
+
+unsigned char __node_distances[MAX_NUMNODES][MAX_NUMNODES];
+EXPORT_SYMBOL(__node_distances);
+
+static int __init compute_node_distance(nasid_t nasid_a, nasid_t nasid_b)
+{
+	klrou_t *router, *router_a = NULL, *router_b = NULL;
+	lboard_t *brd, *dest_brd;
+	nasid_t nasid;
+	int port;
+
+	/* Figure out which routers nodes in question are connected to */
+	for_each_online_node(nasid) {
+		brd = find_lboard_class((lboard_t *)KL_CONFIG_INFO(nasid),
+					KLTYPE_ROUTER);
+
+		if (!brd)
+			continue;
+
+		do {
+			if (brd->brd_flags & DUPLICATE_BOARD)
+				continue;
+
+			router = (klrou_t *)NODE_OFFSET_TO_K0(NASID_GET(brd), brd->brd_compts[0]);
+			router->rou_rflag = 0;
+
+			for (port = 1; port <= MAX_ROUTER_PORTS; port++) {
+				if (router->rou_port[port].port_nasid == INVALID_NASID)
+					continue;
+
+				dest_brd = (lboard_t *)NODE_OFFSET_TO_K0(
+					router->rou_port[port].port_nasid,
+					router->rou_port[port].port_offset);
+
+				if (dest_brd->brd_type == KLTYPE_IP27) {
+					if (dest_brd->brd_nasid == nasid_a)
+						router_a = router;
+					if (dest_brd->brd_nasid == nasid_b)
+						router_b = router;
+				}
+			}
+
+		} while ((brd = find_lboard_class(KLCF_NEXT(brd), KLTYPE_ROUTER)));
+	}
+
+	if (nasid_a == nasid_b)
+		return LOCAL_DISTANCE;
+
+	if (router_a == router_b)
+		return LOCAL_DISTANCE + 1;
+
+	if (router_a == NULL) {
+		pr_info("node_distance: router_a NULL\n");
+		return 255;
+	}
+	if (router_b == NULL) {
+		pr_info("node_distance: router_b NULL\n");
+		return 255;
+	}
+
+	router_distance = 100;
+	router_recurse(router_a, router_b, 2);
+
+	return LOCAL_DISTANCE + router_distance;
+}
+
+static void __init init_topology_matrix(void)
+{
+	nasid_t row, col;
+
+	for (row = 0; row < MAX_NUMNODES; row++)
+		for (col = 0; col < MAX_NUMNODES; col++)
+			__node_distances[row][col] = -1;
+
+	for_each_online_node(row) {
+		for_each_online_node(col) {
+			__node_distances[row][col] =
+				compute_node_distance(row, col);
+		}
+	}
+}
+
+static void __init dump_topology(void)
+{
+	nasid_t nasid;
+	lboard_t *brd, *dest_brd;
+	int port;
+	int router_num = 0;
+	klrou_t *router;
+	nasid_t row, col;
+
+	pr_info("************** Topology ********************\n");
+
+	pr_info("    ");
+	for_each_online_node(col)
+		pr_cont("%02d ", col);
+	pr_cont("\n");
+	for_each_online_node(row) {
+		pr_info("%02d  ", row);
+		for_each_online_node(col)
+			pr_cont("%2d ", node_distance(row, col));
+		pr_cont("\n");
+	}
+
+	for_each_online_node(nasid) {
+		brd = find_lboard_class((lboard_t *)KL_CONFIG_INFO(nasid),
+					KLTYPE_ROUTER);
+
+		if (!brd)
+			continue;
+
+		do {
+			if (brd->brd_flags & DUPLICATE_BOARD)
+				continue;
+			pr_cont("Router %d:", router_num);
+			router_num++;
+
+			router = (klrou_t *)NODE_OFFSET_TO_K0(NASID_GET(brd), brd->brd_compts[0]);
+
+			for (port = 1; port <= MAX_ROUTER_PORTS; port++) {
+				if (router->rou_port[port].port_nasid == INVALID_NASID)
+					continue;
+
+				dest_brd = (lboard_t *)NODE_OFFSET_TO_K0(
+					router->rou_port[port].port_nasid,
+					router->rou_port[port].port_offset);
+
+				if (dest_brd->brd_type == KLTYPE_IP27)
+					pr_cont(" %d", dest_brd->brd_nasid);
+				if (dest_brd->brd_type == KLTYPE_ROUTER)
+					pr_cont(" r");
+			}
+			pr_cont("\n");
+
+		} while ( (brd = find_lboard_class(KLCF_NEXT(brd), KLTYPE_ROUTER)) );
+	}
+}
+
+static unsigned long __init slot_getbasepfn(nasid_t nasid, int slot)
+{
+	return ((unsigned long)nasid << PFN_NASIDSHFT) | (slot << SLOT_PFNSHIFT);
+}
+
+static unsigned long __init slot_psize_compute(nasid_t nasid, int slot)
+{
+	lboard_t *brd;
+	klmembnk_t *banks;
+	unsigned long size;
+
+	/* Find the node board */
+	brd = find_lboard((lboard_t *)KL_CONFIG_INFO(nasid), KLTYPE_IP27);
+	if (!brd)
+		return 0;
+
+	/* Get the memory bank structure */
+	banks = (klmembnk_t *) find_first_component(brd, KLSTRUCT_MEMBNK);
+	if (!banks)
+		return 0;
+
+	/* Size in _Megabytes_ */
+	size = (unsigned long)banks->membnk_bnksz[slot/4];
+
+	/* hack for 128 dimm banks */
+	if (size <= 128) {
+		if (slot % 4 == 0) {
+			size <<= 20;		/* size in bytes */
+			return size >> PAGE_SHIFT;
+		} else
+			return 0;
+	} else {
+		size /= 4;
+		size <<= 20;
+		return size >> PAGE_SHIFT;
+	}
+}
+
+static void __init mlreset(void)
+{
+	u64 region_mask;
+	nasid_t nasid;
+
+	master_nasid = get_nasid();
+
+	/*
+	 * Probe for all CPUs - this creates the cpumask and sets up the
+	 * mapping tables.  We need to do this as early as possible.
+	 */
+#ifdef CONFIG_SMP
+	cpu_node_probe();
+#endif
+
+	init_topology_matrix();
+	dump_topology();
+
+	region_mask = gen_region_mask();
+
+	setup_replication_mask();
+
+	/*
+	 * Set all nodes' calias sizes to 8k
+	 */
+	for_each_online_node(nasid) {
+		/*
+		 * Always have node 0 in the region mask, otherwise
+		 * CALIAS accesses get exceptions since the hub
+		 * thinks it is a node 0 address.
+		 */
+		REMOTE_HUB_S(nasid, PI_REGION_PRESENT, (region_mask | 1));
+		REMOTE_HUB_S(nasid, PI_CALIAS_SIZE, PI_CALIAS_SIZE_0);
+
+#ifdef LATER
+		/*
+		 * Set up all hubs to have a big window pointing at
+		 * widget 0. Memory mode, widget 0, offset 0
+		 */
+		REMOTE_HUB_S(nasid, IIO_ITTE(SWIN0_BIGWIN),
+			((HUB_PIO_MAP_TO_MEM << IIO_ITTE_IOSP_SHIFT) |
+			(0 << IIO_ITTE_WIDGET_SHIFT)));
+#endif
+	}
+}
+
+static void __init szmem(void)
+{
+	unsigned long slot_psize, slot0sz = 0, nodebytes;	/* Hack to detect problem configs */
+	int slot;
+	nasid_t node;
+
+	for_each_online_node(node) {
+		nodebytes = 0;
+		for (slot = 0; slot < MAX_MEM_SLOTS; slot++) {
+			slot_psize = slot_psize_compute(node, slot);
+			if (slot == 0)
+				slot0sz = slot_psize;
+			/*
+			 * We need to refine the hack when we have replicated
+			 * kernel text.
+			 */
+			nodebytes += (1LL << SLOT_SHIFT);
+
+			if (!slot_psize)
+				continue;
+
+			if ((nodebytes >> PAGE_SHIFT) * (sizeof(struct page)) >
+						(slot0sz << PAGE_SHIFT)) {
+				pr_info("Ignoring slot %d onwards on node %d\n",
+								slot, node);
+				slot = MAX_MEM_SLOTS;
+				continue;
+			}
+			memblock_add_node(PFN_PHYS(slot_getbasepfn(node, slot)),
+					  PFN_PHYS(slot_psize), node,
+					  MEMBLOCK_NONE);
+		}
+	}
+}
+
+static void __init node_mem_init(nasid_t node)
+{
+	unsigned long slot_firstpfn = slot_getbasepfn(node, 0);
+	unsigned long slot_freepfn = node_getfirstfree(node);
+	unsigned long start_pfn, end_pfn;
+
+	get_pfn_range_for_nid(node, &start_pfn, &end_pfn);
+
+	/*
+	 * Allocate the node data structures on the node first.
+	 */
+	__node_data[node] = __va(slot_freepfn << PAGE_SHIFT);
+	memset(__node_data[node], 0, PAGE_SIZE);
+
+	NODE_DATA(node)->node_start_pfn = start_pfn;
+	NODE_DATA(node)->node_spanned_pages = end_pfn - start_pfn;
+
+	cpumask_clear(&hub_data(node)->h_cpus);
+
+	slot_freepfn += PFN_UP(sizeof(struct pglist_data) +
+			       sizeof(struct hub_data));
+
+	memblock_reserve(slot_firstpfn << PAGE_SHIFT,
+			 ((slot_freepfn - slot_firstpfn) << PAGE_SHIFT));
+}
+
+/*
+ * A node with nothing.	 We use it to avoid any special casing in
+ * cpumask_of_node
+ */
+static struct node_data null_node = {
+	.hub = {
+		.h_cpus = CPU_MASK_NONE
+	}
+};
+
+/*
+ * Currently, the intranode memory hole support assumes that each slot
+ * contains at least 32 MBytes of memory. We assume all bootmem data
+ * fits on the first slot.
+ */
+void __init prom_meminit(void)
+{
+	nasid_t node;
+
+	mlreset();
+	szmem();
+	max_low_pfn = PHYS_PFN(memblock_end_of_DRAM());
+
+	for (node = 0; node < MAX_NUMNODES; node++) {
+		if (node_online(node)) {
+			node_mem_init(node);
+			continue;
+		}
+		__node_data[node] = &null_node;
+	}
+}
+
+extern void setup_zero_pages(void);
+
+void __init paging_init(void)
+{
+	unsigned long zones_size[MAX_NR_ZONES] = {0, };
+
+	pagetable_init();
+	zones_size[ZONE_NORMAL] = max_low_pfn;
+	free_area_init(zones_size);
+}
+
+void __init mem_init(void)
+{
+	high_memory = (void *) __va(get_num_physpages() << PAGE_SHIFT);
+	memblock_free_all();
+	setup_zero_pages();	/* This comes from node 0 */
+}
+
+pg_data_t * __init arch_alloc_nodedata(int nid)
+{
+	return memblock_alloc(sizeof(pg_data_t), SMP_CACHE_BYTES);
+}
+
+void arch_refresh_nodedata(int nid, pg_data_t *pgdat)
+{
+	__node_data[nid] = (struct node_data *)pgdat;
+}
diff --git a/arch/mips/sgi-ip27/ip27-nmi.c b/arch/mips/sgi-ip27/ip27-nmi.c
new file mode 100644
index 000000000..84889b57d
--- /dev/null
+++ b/arch/mips/sgi-ip27/ip27-nmi.c
@@ -0,0 +1,240 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/kernel.h>
+#include <linux/mmzone.h>
+#include <linux/nodemask.h>
+#include <linux/spinlock.h>
+#include <linux/smp.h>
+#include <linux/atomic.h>
+#include <asm/sn/types.h>
+#include <asm/sn/addrs.h>
+#include <asm/sn/nmi.h>
+#include <asm/sn/arch.h>
+#include <asm/sn/agent.h>
+
+#if 0
+#define NODE_NUM_CPUS(n)	CNODE_NUM_CPUS(n)
+#else
+#define NODE_NUM_CPUS(n)	CPUS_PER_NODE
+#endif
+
+#define SEND_NMI(_nasid, _slice)	\
+	REMOTE_HUB_S((_nasid),  (PI_NMI_A + ((_slice) * PI_NMI_OFFSET)), 1)
+
+typedef unsigned long machreg_t;
+
+static arch_spinlock_t nmi_lock = __ARCH_SPIN_LOCK_UNLOCKED;
+
+/*
+ * Let's see what else we need to do here. Set up sp, gp?
+ */
+void nmi_dump(void)
+{
+	void cont_nmi_dump(void);
+
+	cont_nmi_dump();
+}
+
+void install_cpu_nmi_handler(int slice)
+{
+	nmi_t *nmi_addr;
+
+	nmi_addr = (nmi_t *)NMI_ADDR(get_nasid(), slice);
+	if (nmi_addr->call_addr)
+		return;
+	nmi_addr->magic = NMI_MAGIC;
+	nmi_addr->call_addr = (void *)nmi_dump;
+	nmi_addr->call_addr_c =
+		(void *)(~((unsigned long)(nmi_addr->call_addr)));
+	nmi_addr->call_parm = 0;
+}
+
+/*
+ * Copy the cpu registers which have been saved in the IP27prom format
+ * into the eframe format for the node under consideration.
+ */
+
+void nmi_cpu_eframe_save(nasid_t nasid, int slice)
+{
+	struct reg_struct *nr;
+	int		i;
+
+	/* Get the pointer to the current cpu's register set. */
+	nr = (struct reg_struct *)
+		(TO_UNCAC(TO_NODE(nasid, IP27_NMI_KREGS_OFFSET)) +
+		slice * IP27_NMI_KREGS_CPU_SIZE);
+
+	pr_emerg("NMI nasid %d: slice %d\n", nasid, slice);
+
+	/*
+	 * Saved main processor registers
+	 */
+	for (i = 0; i < 32; ) {
+		if ((i % 4) == 0)
+			pr_emerg("$%2d   :", i);
+		pr_cont(" %016lx", nr->gpr[i]);
+
+		i++;
+		if ((i % 4) == 0)
+			pr_cont("\n");
+	}
+
+	pr_emerg("Hi    : (value lost)\n");
+	pr_emerg("Lo    : (value lost)\n");
+
+	/*
+	 * Saved cp0 registers
+	 */
+	pr_emerg("epc   : %016lx %pS\n", nr->epc, (void *)nr->epc);
+	pr_emerg("%s\n", print_tainted());
+	pr_emerg("ErrEPC: %016lx %pS\n", nr->error_epc, (void *)nr->error_epc);
+	pr_emerg("ra    : %016lx %pS\n", nr->gpr[31], (void *)nr->gpr[31]);
+	pr_emerg("Status: %08lx	      ", nr->sr);
+
+	if (nr->sr & ST0_KX)
+		pr_cont("KX ");
+	if (nr->sr & ST0_SX)
+		pr_cont("SX ");
+	if (nr->sr & ST0_UX)
+		pr_cont("UX ");
+
+	switch (nr->sr & ST0_KSU) {
+	case KSU_USER:
+		pr_cont("USER ");
+		break;
+	case KSU_SUPERVISOR:
+		pr_cont("SUPERVISOR ");
+		break;
+	case KSU_KERNEL:
+		pr_cont("KERNEL ");
+		break;
+	default:
+		pr_cont("BAD_MODE ");
+		break;
+	}
+
+	if (nr->sr & ST0_ERL)
+		pr_cont("ERL ");
+	if (nr->sr & ST0_EXL)
+		pr_cont("EXL ");
+	if (nr->sr & ST0_IE)
+		pr_cont("IE ");
+	pr_cont("\n");
+
+	pr_emerg("Cause : %08lx\n", nr->cause);
+	pr_emerg("PrId  : %08x\n", read_c0_prid());
+	pr_emerg("BadVA : %016lx\n", nr->badva);
+	pr_emerg("CErr  : %016lx\n", nr->cache_err);
+	pr_emerg("NMI_SR: %016lx\n", nr->nmi_sr);
+
+	pr_emerg("\n");
+}
+
+void nmi_dump_hub_irq(nasid_t nasid, int slice)
+{
+	u64 mask0, mask1, pend0, pend1;
+
+	if (slice == 0) {				/* Slice A */
+		mask0 = REMOTE_HUB_L(nasid, PI_INT_MASK0_A);
+		mask1 = REMOTE_HUB_L(nasid, PI_INT_MASK1_A);
+	} else {					/* Slice B */
+		mask0 = REMOTE_HUB_L(nasid, PI_INT_MASK0_B);
+		mask1 = REMOTE_HUB_L(nasid, PI_INT_MASK1_B);
+	}
+
+	pend0 = REMOTE_HUB_L(nasid, PI_INT_PEND0);
+	pend1 = REMOTE_HUB_L(nasid, PI_INT_PEND1);
+
+	pr_emerg("PI_INT_MASK0: %16llx PI_INT_MASK1: %16llx\n", mask0, mask1);
+	pr_emerg("PI_INT_PEND0: %16llx PI_INT_PEND1: %16llx\n", pend0, pend1);
+	pr_emerg("\n\n");
+}
+
+/*
+ * Copy the cpu registers which have been saved in the IP27prom format
+ * into the eframe format for the node under consideration.
+ */
+void nmi_node_eframe_save(nasid_t nasid)
+{
+	int slice;
+
+	if (nasid == INVALID_NASID)
+		return;
+
+	/* Save the registers into eframe for each cpu */
+	for (slice = 0; slice < NODE_NUM_CPUS(slice); slice++) {
+		nmi_cpu_eframe_save(nasid, slice);
+		nmi_dump_hub_irq(nasid, slice);
+	}
+}
+
+/*
+ * Save the nmi cpu registers for all cpus in the system.
+ */
+void
+nmi_eframes_save(void)
+{
+	nasid_t nasid;
+
+	for_each_online_node(nasid)
+		nmi_node_eframe_save(nasid);
+}
+
+void
+cont_nmi_dump(void)
+{
+#ifndef REAL_NMI_SIGNAL
+	static atomic_t nmied_cpus = ATOMIC_INIT(0);
+
+	atomic_inc(&nmied_cpus);
+#endif
+	/*
+	 * Only allow 1 cpu to proceed
+	 */
+	arch_spin_lock(&nmi_lock);
+
+#ifdef REAL_NMI_SIGNAL
+	/*
+	 * Wait up to 15 seconds for the other cpus to respond to the NMI.
+	 * If a cpu has not responded after 10 sec, send it 1 additional NMI.
+	 * This is for 2 reasons:
+	 *	- sometimes a MMSC fail to NMI all cpus.
+	 *	- on 512p SN0 system, the MMSC will only send NMIs to
+	 *	  half the cpus. Unfortunately, we don't know which cpus may be
+	 *	  NMIed - it depends on how the site chooses to configure.
+	 *
+	 * Note: it has been measure that it takes the MMSC up to 2.3 secs to
+	 * send NMIs to all cpus on a 256p system.
+	 */
+	for (i=0; i < 1500; i++) {
+		for_each_online_node(node)
+			if (NODEPDA(node)->dump_count == 0)
+				break;
+		if (node == MAX_NUMNODES)
+			break;
+		if (i == 1000) {
+			for_each_online_node(node)
+				if (NODEPDA(node)->dump_count == 0) {
+					cpu = cpumask_first(cpumask_of_node(node));
+					for (n=0; n < CNODE_NUM_CPUS(node); cpu++, n++) {
+						CPUMASK_SETB(nmied_cpus, cpu);
+						/*
+						 * cputonasid, cputoslice
+						 * needs kernel cpuid
+						 */
+						SEND_NMI((cputonasid(cpu)), (cputoslice(cpu)));
+					}
+				}
+
+		}
+		udelay(10000);
+	}
+#else
+	while (atomic_read(&nmied_cpus) != num_online_cpus());
+#endif
+
+	/*
+	 * Save the nmi cpu registers for all cpu in the eframe format.
+	 */
+	nmi_eframes_save();
+	LOCAL_HUB_S(NI_PORT_RESET, NPR_PORTRESET | NPR_LOCALRESET);
+}
diff --git a/arch/mips/sgi-ip27/ip27-reset.c b/arch/mips/sgi-ip27/ip27-reset.c
new file mode 100644
index 000000000..5ac5ad638
--- /dev/null
+++ b/arch/mips/sgi-ip27/ip27-reset.c
@@ -0,0 +1,81 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Reset an IP27.
+ *
+ * Copyright (C) 1997, 1998, 1999, 2000, 06 by Ralf Baechle
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ */
+#include <linux/compiler.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/timer.h>
+#include <linux/smp.h>
+#include <linux/mmzone.h>
+#include <linux/nodemask.h>
+#include <linux/pm.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/reboot.h>
+#include <asm/sgialib.h>
+#include <asm/sn/addrs.h>
+#include <asm/sn/agent.h>
+#include <asm/sn/arch.h>
+#include <asm/sn/gda.h>
+
+#include "ip27-common.h"
+
+void machine_restart(char *command) __noreturn;
+void machine_halt(void) __noreturn;
+void machine_power_off(void) __noreturn;
+
+#define noreturn while(1);				/* Silence gcc.	 */
+
+/* XXX How to pass the reboot command to the firmware??? */
+static void ip27_machine_restart(char *command)
+{
+#if 0
+	int i;
+#endif
+
+	printk("Reboot started from CPU %d\n", smp_processor_id());
+#ifdef CONFIG_SMP
+	smp_send_stop();
+#endif
+#if 0
+	for_each_online_node(i)
+		REMOTE_HUB_S(i, PROMOP_REG, PROMOP_REBOOT);
+#else
+	LOCAL_HUB_S(NI_PORT_RESET, NPR_PORTRESET | NPR_LOCALRESET);
+#endif
+	noreturn;
+}
+
+static void ip27_machine_halt(void)
+{
+	int i;
+
+#ifdef CONFIG_SMP
+	smp_send_stop();
+#endif
+	for_each_online_node(i)
+		REMOTE_HUB_S(i, PROMOP_REG, PROMOP_RESTART);
+	LOCAL_HUB_S(NI_PORT_RESET, NPR_PORTRESET | NPR_LOCALRESET);
+	noreturn;
+}
+
+static void ip27_machine_power_off(void)
+{
+	/* To do ...  */
+	noreturn;
+}
+
+void ip27_reboot_setup(void)
+{
+	_machine_restart = ip27_machine_restart;
+	_machine_halt = ip27_machine_halt;
+	pm_power_off = ip27_machine_power_off;
+}
diff --git a/arch/mips/sgi-ip27/ip27-smp.c b/arch/mips/sgi-ip27/ip27-smp.c
new file mode 100644
index 000000000..5d2652a1d
--- /dev/null
+++ b/arch/mips/sgi-ip27/ip27-smp.c
@@ -0,0 +1,189 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General
+ * Public License.  See the file "COPYING" in the main directory of this
+ * archive for more details.
+ *
+ * Copyright (C) 2000 - 2001 by Kanoj Sarcar (kanoj@sgi.com)
+ * Copyright (C) 2000 - 2001 by Silicon Graphics, Inc.
+ */
+#include <linux/init.h>
+#include <linux/sched.h>
+#include <linux/sched/task_stack.h>
+#include <linux/topology.h>
+#include <linux/nodemask.h>
+
+#include <asm/page.h>
+#include <asm/processor.h>
+#include <asm/ptrace.h>
+#include <asm/sn/agent.h>
+#include <asm/sn/arch.h>
+#include <asm/sn/gda.h>
+#include <asm/sn/intr.h>
+#include <asm/sn/klconfig.h>
+#include <asm/sn/launch.h>
+#include <asm/sn/mapped_kernel.h>
+#include <asm/sn/types.h>
+
+#include "ip27-common.h"
+
+static int node_scan_cpus(nasid_t nasid, int highest)
+{
+	static int cpus_found;
+	lboard_t *brd;
+	klcpu_t *acpu;
+	cpuid_t cpuid;
+
+	brd = find_lboard((lboard_t *)KL_CONFIG_INFO(nasid), KLTYPE_IP27);
+
+	do {
+		acpu = (klcpu_t *)find_first_component(brd, KLSTRUCT_CPU);
+		while (acpu) {
+			cpuid = acpu->cpu_info.virtid;
+			/* Only let it join in if it's marked enabled */
+			if ((acpu->cpu_info.flags & KLINFO_ENABLE) &&
+			    (cpus_found != NR_CPUS)) {
+				if (cpuid > highest)
+					highest = cpuid;
+				set_cpu_possible(cpuid, true);
+				cputonasid(cpus_found) = nasid;
+				cputoslice(cpus_found) = acpu->cpu_info.physid;
+				sn_cpu_info[cpus_found].p_speed =
+							acpu->cpu_speed;
+				cpus_found++;
+			}
+			acpu = (klcpu_t *)find_component(brd, (klinfo_t *)acpu,
+								KLSTRUCT_CPU);
+		}
+		brd = KLCF_NEXT(brd);
+		if (!brd)
+			break;
+
+		brd = find_lboard(brd, KLTYPE_IP27);
+	} while (brd);
+
+	return highest;
+}
+
+void cpu_node_probe(void)
+{
+	int i, highest = 0;
+	gda_t *gdap = GDA;
+
+	nodes_clear(node_online_map);
+	for (i = 0; i < MAX_NUMNODES; i++) {
+		nasid_t nasid = gdap->g_nasidtable[i];
+		if (nasid == INVALID_NASID)
+			break;
+		node_set_online(nasid);
+		highest = node_scan_cpus(nasid, highest);
+	}
+
+	printk("Discovered %d cpus on %d nodes\n", highest + 1, num_online_nodes());
+}
+
+static __init void intr_clear_all(nasid_t nasid)
+{
+	int i;
+
+	REMOTE_HUB_S(nasid, PI_INT_MASK0_A, 0);
+	REMOTE_HUB_S(nasid, PI_INT_MASK0_B, 0);
+	REMOTE_HUB_S(nasid, PI_INT_MASK1_A, 0);
+	REMOTE_HUB_S(nasid, PI_INT_MASK1_B, 0);
+
+	for (i = 0; i < 128; i++)
+		REMOTE_HUB_CLR_INTR(nasid, i);
+}
+
+static void ip27_send_ipi_single(int destid, unsigned int action)
+{
+	int irq;
+
+	switch (action) {
+	case SMP_RESCHEDULE_YOURSELF:
+		irq = CPU_RESCHED_A_IRQ;
+		break;
+	case SMP_CALL_FUNCTION:
+		irq = CPU_CALL_A_IRQ;
+		break;
+	default:
+		panic("sendintr");
+	}
+
+	irq += cputoslice(destid);
+
+	/*
+	 * Set the interrupt bit associated with the CPU we want to
+	 * send the interrupt to.
+	 */
+	REMOTE_HUB_SEND_INTR(cpu_to_node(destid), irq);
+}
+
+static void ip27_send_ipi_mask(const struct cpumask *mask, unsigned int action)
+{
+	unsigned int i;
+
+	for_each_cpu(i, mask)
+		ip27_send_ipi_single(i, action);
+}
+
+static void ip27_init_cpu(void)
+{
+	per_cpu_init();
+}
+
+static void ip27_smp_finish(void)
+{
+	hub_rt_clock_event_init();
+	local_irq_enable();
+}
+
+/*
+ * Launch a slave into smp_bootstrap().	 It doesn't take an argument, and we
+ * set sp to the kernel stack of the newly created idle process, gp to the proc
+ * struct so that current_thread_info() will work.
+ */
+static int ip27_boot_secondary(int cpu, struct task_struct *idle)
+{
+	unsigned long gp = (unsigned long)task_thread_info(idle);
+	unsigned long sp = __KSTK_TOS(idle);
+
+	LAUNCH_SLAVE(cputonasid(cpu), cputoslice(cpu),
+		(launch_proc_t)MAPPED_KERN_RW_TO_K0(smp_bootstrap),
+		0, (void *) sp, (void *) gp);
+	return 0;
+}
+
+static void __init ip27_smp_setup(void)
+{
+	nasid_t nasid;
+
+	for_each_online_node(nasid) {
+		if (nasid == 0)
+			continue;
+		intr_clear_all(nasid);
+	}
+
+	replicate_kernel_text();
+
+	/*
+	 * PROM sets up system, that boot cpu is always first CPU on nasid 0
+	 */
+	cputonasid(0) = 0;
+	cputoslice(0) = LOCAL_HUB_L(PI_CPU_NUM);
+}
+
+static void __init ip27_prepare_cpus(unsigned int max_cpus)
+{
+	/* We already did everything necessary earlier */
+}
+
+const struct plat_smp_ops ip27_smp_ops = {
+	.send_ipi_single	= ip27_send_ipi_single,
+	.send_ipi_mask		= ip27_send_ipi_mask,
+	.init_secondary		= ip27_init_cpu,
+	.smp_finish		= ip27_smp_finish,
+	.boot_secondary		= ip27_boot_secondary,
+	.smp_setup		= ip27_smp_setup,
+	.prepare_cpus		= ip27_prepare_cpus,
+	.prepare_boot_cpu	= ip27_init_cpu,
+};
diff --git a/arch/mips/sgi-ip27/ip27-timer.c b/arch/mips/sgi-ip27/ip27-timer.c
new file mode 100644
index 000000000..444b5e0e9
--- /dev/null
+++ b/arch/mips/sgi-ip27/ip27-timer.c
@@ -0,0 +1,160 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 1999, 2000, 05, 06 Ralf Baechle (ralf@linux-mips.org)
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ */
+#include <linux/bcd.h>
+#include <linux/clockchips.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/sched_clock.h>
+#include <linux/interrupt.h>
+#include <linux/kernel_stat.h>
+#include <linux/param.h>
+#include <linux/smp.h>
+#include <linux/time.h>
+#include <linux/timex.h>
+#include <linux/mm.h>
+#include <linux/platform_device.h>
+
+#include <asm/time.h>
+#include <asm/sgialib.h>
+#include <asm/sn/klconfig.h>
+#include <asm/sn/arch.h>
+#include <asm/sn/addrs.h>
+#include <asm/sn/agent.h>
+
+#include "ip27-common.h"
+
+static int rt_next_event(unsigned long delta, struct clock_event_device *evt)
+{
+	unsigned int cpu = smp_processor_id();
+	int slice = cputoslice(cpu);
+	unsigned long cnt;
+
+	cnt = LOCAL_HUB_L(PI_RT_COUNT);
+	cnt += delta;
+	LOCAL_HUB_S(PI_RT_COMPARE_A + PI_COUNT_OFFSET * slice, cnt);
+
+	return LOCAL_HUB_L(PI_RT_COUNT) >= cnt ? -ETIME : 0;
+}
+
+static DEFINE_PER_CPU(struct clock_event_device, hub_rt_clockevent);
+static DEFINE_PER_CPU(char [11], hub_rt_name);
+
+static irqreturn_t hub_rt_counter_handler(int irq, void *dev_id)
+{
+	unsigned int cpu = smp_processor_id();
+	struct clock_event_device *cd = &per_cpu(hub_rt_clockevent, cpu);
+	int slice = cputoslice(cpu);
+
+	/*
+	 * Ack
+	 */
+	LOCAL_HUB_S(PI_RT_PEND_A + PI_COUNT_OFFSET * slice, 0);
+	cd->event_handler(cd);
+
+	return IRQ_HANDLED;
+}
+
+struct irqaction hub_rt_irqaction = {
+	.handler	= hub_rt_counter_handler,
+	.percpu_dev_id	= &hub_rt_clockevent,
+	.flags		= IRQF_PERCPU | IRQF_TIMER,
+	.name		= "hub-rt",
+};
+
+/*
+ * This is a hack; we really need to figure these values out dynamically
+ *
+ * Since 800 ns works very well with various HUB frequencies, such as
+ * 360, 380, 390 and 400 MHZ, we use 800 ns rtc cycle time.
+ *
+ * Ralf: which clock rate is used to feed the counter?
+ */
+#define NSEC_PER_CYCLE		800
+#define CYCLES_PER_SEC		(NSEC_PER_SEC / NSEC_PER_CYCLE)
+
+void hub_rt_clock_event_init(void)
+{
+	unsigned int cpu = smp_processor_id();
+	struct clock_event_device *cd = &per_cpu(hub_rt_clockevent, cpu);
+	unsigned char *name = per_cpu(hub_rt_name, cpu);
+
+	sprintf(name, "hub-rt %d", cpu);
+	cd->name		= name;
+	cd->features		= CLOCK_EVT_FEAT_ONESHOT;
+	clockevent_set_clock(cd, CYCLES_PER_SEC);
+	cd->max_delta_ns	= clockevent_delta2ns(0xfffffffffffff, cd);
+	cd->max_delta_ticks	= 0xfffffffffffff;
+	cd->min_delta_ns	= clockevent_delta2ns(0x300, cd);
+	cd->min_delta_ticks	= 0x300;
+	cd->rating		= 200;
+	cd->irq			= IP27_RT_TIMER_IRQ;
+	cd->cpumask		= cpumask_of(cpu);
+	cd->set_next_event	= rt_next_event;
+	clockevents_register_device(cd);
+
+	enable_percpu_irq(IP27_RT_TIMER_IRQ, IRQ_TYPE_NONE);
+}
+
+static void __init hub_rt_clock_event_global_init(void)
+{
+	irq_set_handler(IP27_RT_TIMER_IRQ, handle_percpu_devid_irq);
+	irq_set_percpu_devid(IP27_RT_TIMER_IRQ);
+	setup_percpu_irq(IP27_RT_TIMER_IRQ, &hub_rt_irqaction);
+}
+
+static u64 hub_rt_read(struct clocksource *cs)
+{
+	return REMOTE_HUB_L(cputonasid(0), PI_RT_COUNT);
+}
+
+struct clocksource hub_rt_clocksource = {
+	.name	= "HUB-RT",
+	.rating = 200,
+	.read	= hub_rt_read,
+	.mask	= CLOCKSOURCE_MASK(52),
+	.flags	= CLOCK_SOURCE_IS_CONTINUOUS,
+};
+
+static u64 notrace hub_rt_read_sched_clock(void)
+{
+	return REMOTE_HUB_L(cputonasid(0), PI_RT_COUNT);
+}
+
+static void __init hub_rt_clocksource_init(void)
+{
+	struct clocksource *cs = &hub_rt_clocksource;
+
+	clocksource_register_hz(cs, CYCLES_PER_SEC);
+
+	sched_clock_register(hub_rt_read_sched_clock, 52, CYCLES_PER_SEC);
+}
+
+void __init plat_time_init(void)
+{
+	hub_rt_clocksource_init();
+	hub_rt_clock_event_global_init();
+	hub_rt_clock_event_init();
+}
+
+void hub_rtc_init(nasid_t nasid)
+{
+
+	/*
+	 * We only need to initialize the current node.
+	 * If this is not the current node then it is a cpuless
+	 * node and timeouts will not happen there.
+	 */
+	if (get_nasid() == nasid) {
+		LOCAL_HUB_S(PI_RT_EN_A, 1);
+		LOCAL_HUB_S(PI_RT_EN_B, 1);
+		LOCAL_HUB_S(PI_PROF_EN_A, 0);
+		LOCAL_HUB_S(PI_PROF_EN_B, 0);
+		LOCAL_HUB_S(PI_RT_COUNT, 0);
+		LOCAL_HUB_S(PI_RT_PEND_A, 0);
+		LOCAL_HUB_S(PI_RT_PEND_B, 0);
+	}
+}
diff --git a/arch/mips/sgi-ip27/ip27-xtalk.c b/arch/mips/sgi-ip27/ip27-xtalk.c
new file mode 100644
index 000000000..5143d1cf8
--- /dev/null
+++ b/arch/mips/sgi-ip27/ip27-xtalk.c
@@ -0,0 +1,242 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 1999, 2000 Ralf Baechle (ralf@gnu.org)
+ * Copyright (C) 1999, 2000 Silcon Graphics, Inc.
+ * Copyright (C) 2004 Christoph Hellwig.
+ *
+ * Generic XTALK initialization code
+ */
+
+#include <linux/kernel.h>
+#include <linux/smp.h>
+#include <linux/platform_device.h>
+#include <linux/platform_data/sgi-w1.h>
+#include <linux/platform_data/xtalk-bridge.h>
+#include <asm/sn/addrs.h>
+#include <asm/sn/types.h>
+#include <asm/sn/klconfig.h>
+#include <asm/pci/bridge.h>
+#include <asm/xtalk/xtalk.h>
+
+
+#define XBOW_WIDGET_PART_NUM	0x0
+#define XXBOW_WIDGET_PART_NUM	0xd000	/* Xbow in Xbridge */
+#define BASE_XBOW_PORT		8     /* Lowest external port */
+
+static void bridge_platform_create(nasid_t nasid, int widget, int masterwid)
+{
+	struct xtalk_bridge_platform_data *bd;
+	struct sgi_w1_platform_data *wd;
+	struct platform_device *pdev_wd;
+	struct platform_device *pdev_bd;
+	struct resource w1_res;
+	unsigned long offset;
+
+	offset = NODE_OFFSET(nasid);
+
+	wd = kzalloc(sizeof(*wd), GFP_KERNEL);
+	if (!wd) {
+		pr_warn("xtalk:n%d/%x bridge create out of memory\n", nasid, widget);
+		return;
+	}
+
+	snprintf(wd->dev_id, sizeof(wd->dev_id), "bridge-%012lx",
+		 offset + (widget << SWIN_SIZE_BITS));
+
+	memset(&w1_res, 0, sizeof(w1_res));
+	w1_res.start = offset + (widget << SWIN_SIZE_BITS) +
+				offsetof(struct bridge_regs, b_nic);
+	w1_res.end = w1_res.start + 3;
+	w1_res.flags = IORESOURCE_MEM;
+
+	pdev_wd = platform_device_alloc("sgi_w1", PLATFORM_DEVID_AUTO);
+	if (!pdev_wd) {
+		pr_warn("xtalk:n%d/%x bridge create out of memory\n", nasid, widget);
+		goto err_kfree_wd;
+	}
+	if (platform_device_add_resources(pdev_wd, &w1_res, 1)) {
+		pr_warn("xtalk:n%d/%x bridge failed to add platform resources.\n", nasid, widget);
+		goto err_put_pdev_wd;
+	}
+	if (platform_device_add_data(pdev_wd, wd, sizeof(*wd))) {
+		pr_warn("xtalk:n%d/%x bridge failed to add platform data.\n", nasid, widget);
+		goto err_put_pdev_wd;
+	}
+	if (platform_device_add(pdev_wd)) {
+		pr_warn("xtalk:n%d/%x bridge failed to add platform device.\n", nasid, widget);
+		goto err_put_pdev_wd;
+	}
+	/* platform_device_add_data() duplicates the data */
+	kfree(wd);
+
+	bd = kzalloc(sizeof(*bd), GFP_KERNEL);
+	if (!bd) {
+		pr_warn("xtalk:n%d/%x bridge create out of memory\n", nasid, widget);
+		goto err_unregister_pdev_wd;
+	}
+	pdev_bd = platform_device_alloc("xtalk-bridge", PLATFORM_DEVID_AUTO);
+	if (!pdev_bd) {
+		pr_warn("xtalk:n%d/%x bridge create out of memory\n", nasid, widget);
+		goto err_kfree_bd;
+	}
+
+
+	bd->bridge_addr = RAW_NODE_SWIN_BASE(nasid, widget);
+	bd->intr_addr	= BIT_ULL(47) + 0x01800000 + PI_INT_PEND_MOD;
+	bd->nasid	= nasid;
+	bd->masterwid	= masterwid;
+
+	bd->mem.name	= "Bridge PCI MEM";
+	bd->mem.start	= offset + (widget << SWIN_SIZE_BITS) + BRIDGE_DEVIO0;
+	bd->mem.end	= offset + (widget << SWIN_SIZE_BITS) + SWIN_SIZE - 1;
+	bd->mem.flags	= IORESOURCE_MEM;
+	bd->mem_offset	= offset;
+
+	bd->io.name	= "Bridge PCI IO";
+	bd->io.start	= offset + (widget << SWIN_SIZE_BITS) + BRIDGE_DEVIO0;
+	bd->io.end	= offset + (widget << SWIN_SIZE_BITS) + SWIN_SIZE - 1;
+	bd->io.flags	= IORESOURCE_IO;
+	bd->io_offset	= offset;
+
+	if (platform_device_add_data(pdev_bd, bd, sizeof(*bd))) {
+		pr_warn("xtalk:n%d/%x bridge failed to add platform data.\n", nasid, widget);
+		goto err_put_pdev_bd;
+	}
+	if (platform_device_add(pdev_bd)) {
+		pr_warn("xtalk:n%d/%x bridge failed to add platform device.\n", nasid, widget);
+		goto err_put_pdev_bd;
+	}
+	/* platform_device_add_data() duplicates the data */
+	kfree(bd);
+	pr_info("xtalk:n%d/%x bridge widget\n", nasid, widget);
+	return;
+
+err_put_pdev_bd:
+	platform_device_put(pdev_bd);
+err_kfree_bd:
+	kfree(bd);
+err_unregister_pdev_wd:
+	platform_device_unregister(pdev_wd);
+	return;
+err_put_pdev_wd:
+	platform_device_put(pdev_wd);
+err_kfree_wd:
+	kfree(wd);
+	return;
+}
+
+static int probe_one_port(nasid_t nasid, int widget, int masterwid)
+{
+	widgetreg_t		widget_id;
+	xwidget_part_num_t	partnum;
+
+	widget_id = *(volatile widgetreg_t *)
+		(RAW_NODE_SWIN_BASE(nasid, widget) + WIDGET_ID);
+	partnum = XWIDGET_PART_NUM(widget_id);
+
+	switch (partnum) {
+	case BRIDGE_WIDGET_PART_NUM:
+	case XBRIDGE_WIDGET_PART_NUM:
+		bridge_platform_create(nasid, widget, masterwid);
+		break;
+	default:
+		pr_info("xtalk:n%d/%d unknown widget (0x%x)\n",
+			nasid, widget, partnum);
+		break;
+	}
+
+	return 0;
+}
+
+static int xbow_probe(nasid_t nasid)
+{
+	lboard_t *brd;
+	klxbow_t *xbow_p;
+	unsigned masterwid, i;
+
+	/*
+	 * found xbow, so may have multiple bridges
+	 * need to probe xbow
+	 */
+	brd = find_lboard((lboard_t *)KL_CONFIG_INFO(nasid), KLTYPE_MIDPLANE8);
+	if (!brd)
+		return -ENODEV;
+
+	xbow_p = (klxbow_t *)find_component(brd, NULL, KLSTRUCT_XBOW);
+	if (!xbow_p)
+		return -ENODEV;
+
+	/*
+	 * Okay, here's a xbow. Let's arbitrate and find
+	 * out if we should initialize it. Set enabled
+	 * hub connected at highest or lowest widget as
+	 * master.
+	 */
+#ifdef WIDGET_A
+	i = HUB_WIDGET_ID_MAX + 1;
+	do {
+		i--;
+	} while ((!XBOW_PORT_TYPE_HUB(xbow_p, i)) ||
+		 (!XBOW_PORT_IS_ENABLED(xbow_p, i)));
+#else
+	i = HUB_WIDGET_ID_MIN - 1;
+	do {
+		i++;
+	} while ((!XBOW_PORT_TYPE_HUB(xbow_p, i)) ||
+		 (!XBOW_PORT_IS_ENABLED(xbow_p, i)));
+#endif
+
+	masterwid = i;
+	if (nasid != XBOW_PORT_NASID(xbow_p, i))
+		return 1;
+
+	for (i = HUB_WIDGET_ID_MIN; i <= HUB_WIDGET_ID_MAX; i++) {
+		if (XBOW_PORT_IS_ENABLED(xbow_p, i) &&
+		    XBOW_PORT_TYPE_IO(xbow_p, i))
+			probe_one_port(nasid, i, masterwid);
+	}
+
+	return 0;
+}
+
+static void xtalk_probe_node(nasid_t nasid)
+{
+	volatile u64		hubreg;
+	xwidget_part_num_t	partnum;
+	widgetreg_t		widget_id;
+
+	hubreg = REMOTE_HUB_L(nasid, IIO_LLP_CSR);
+
+	/* check whether the link is up */
+	if (!(hubreg & IIO_LLP_CSR_IS_UP))
+		return;
+
+	widget_id = *(volatile widgetreg_t *)
+		       (RAW_NODE_SWIN_BASE(nasid, 0x0) + WIDGET_ID);
+	partnum = XWIDGET_PART_NUM(widget_id);
+
+	switch (partnum) {
+	case BRIDGE_WIDGET_PART_NUM:
+		bridge_platform_create(nasid, 0x8, 0xa);
+		break;
+	case XBOW_WIDGET_PART_NUM:
+	case XXBOW_WIDGET_PART_NUM:
+		pr_info("xtalk:n%d/0 xbow widget\n", nasid);
+		xbow_probe(nasid);
+		break;
+	default:
+		pr_info("xtalk:n%d/0 unknown widget (0x%x)\n", nasid, partnum);
+		break;
+	}
+}
+
+static int __init xtalk_init(void)
+{
+	nasid_t nasid;
+
+	for_each_online_node(nasid)
+		xtalk_probe_node(nasid);
+
+	return 0;
+}
+arch_initcall(xtalk_init);
diff --git a/arch/mips/sgi-ip30/Makefile b/arch/mips/sgi-ip30/Makefile
new file mode 100644
index 000000000..18cf561b3
--- /dev/null
+++ b/arch/mips/sgi-ip30/Makefile
@@ -0,0 +1,9 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Makefile for the IP30 specific kernel interface routines under Linux.
+#
+
+obj-y	:= ip30-irq.o ip30-power.o ip30-setup.o ip30-timer.o ip30-xtalk.o
+
+obj-$(CONFIG_EARLY_PRINTK)	+= ip30-console.o
+obj-$(CONFIG_SMP)		+= ip30-smp.o
diff --git a/arch/mips/sgi-ip30/Platform b/arch/mips/sgi-ip30/Platform
new file mode 100644
index 000000000..f6f11517e
--- /dev/null
+++ b/arch/mips/sgi-ip30/Platform
@@ -0,0 +1,5 @@
+#
+# SGI-IP30 (Octane/Octane2)
+#
+cflags-$(CONFIG_SGI_IP30)		+= -I$(srctree)/arch/mips/include/asm/mach-ip30
+load-$(CONFIG_SGI_IP30)			+= 0xa800000020004000
diff --git a/arch/mips/sgi-ip30/ip30-common.h b/arch/mips/sgi-ip30/ip30-common.h
new file mode 100644
index 000000000..7b5db24b6
--- /dev/null
+++ b/arch/mips/sgi-ip30/ip30-common.h
@@ -0,0 +1,23 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+#ifndef __IP30_COMMON_H
+#define __IP30_COMMON_H
+
+/*
+ * Power Switch is wired via BaseIO BRIDGE slot #6.
+ *
+ * ACFail is wired via BaseIO BRIDGE slot #7.
+ */
+#define IP30_POWER_IRQ		HEART_L2_INT_POWER_BTN
+
+#define IP30_HEART_L0_IRQ	(MIPS_CPU_IRQ_BASE + 2)
+#define IP30_HEART_L1_IRQ	(MIPS_CPU_IRQ_BASE + 3)
+#define IP30_HEART_L2_IRQ	(MIPS_CPU_IRQ_BASE + 4)
+#define IP30_HEART_TIMER_IRQ	(MIPS_CPU_IRQ_BASE + 5)
+#define IP30_HEART_ERR_IRQ	(MIPS_CPU_IRQ_BASE + 6)
+
+extern void __init ip30_install_ipi(void);
+extern struct plat_smp_ops ip30_smp_ops;
+extern void __init ip30_per_cpu_init(void);
+
+#endif /* __IP30_COMMON_H */
diff --git a/arch/mips/sgi-ip30/ip30-console.c b/arch/mips/sgi-ip30/ip30-console.c
new file mode 100644
index 000000000..b91f8c4fd
--- /dev/null
+++ b/arch/mips/sgi-ip30/ip30-console.c
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include <linux/io.h>
+
+#include <asm/sn/ioc3.h>
+
+static inline struct ioc3_uartregs *console_uart(void)
+{
+	struct ioc3 *ioc3;
+
+	ioc3 = (struct ioc3 *)((void *)(0x900000001f600000));
+	return &ioc3->sregs.uarta;
+}
+
+void prom_putchar(char c)
+{
+	struct ioc3_uartregs *uart = console_uart();
+
+	while ((readb(&uart->iu_lsr) & 0x20) == 0)
+		cpu_relax();
+
+	writeb(c, &uart->iu_thr);
+}
diff --git a/arch/mips/sgi-ip30/ip30-irq.c b/arch/mips/sgi-ip30/ip30-irq.c
new file mode 100644
index 000000000..423c32cb6
--- /dev/null
+++ b/arch/mips/sgi-ip30/ip30-irq.c
@@ -0,0 +1,330 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ip30-irq.c: Highlevel interrupt handling for IP30 architecture.
+ */
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/percpu.h>
+#include <linux/spinlock.h>
+#include <linux/tick.h>
+#include <linux/types.h>
+
+#include <asm/irq_cpu.h>
+#include <asm/sgi/heart.h>
+
+#include "ip30-common.h"
+
+struct heart_irq_data {
+	u64	*irq_mask;
+	int	cpu;
+};
+
+static DECLARE_BITMAP(heart_irq_map, HEART_NUM_IRQS);
+
+static DEFINE_PER_CPU(unsigned long, irq_enable_mask);
+
+static inline int heart_alloc_int(void)
+{
+	int bit;
+
+again:
+	bit = find_first_zero_bit(heart_irq_map, HEART_NUM_IRQS);
+	if (bit >= HEART_NUM_IRQS)
+		return -ENOSPC;
+
+	if (test_and_set_bit(bit, heart_irq_map))
+		goto again;
+
+	return bit;
+}
+
+static void ip30_error_irq(struct irq_desc *desc)
+{
+	u64 pending, mask, cause, error_irqs, err_reg;
+	int cpu = smp_processor_id();
+	int i;
+
+	pending = heart_read(&heart_regs->isr);
+	mask = heart_read(&heart_regs->imr[cpu]);
+	cause = heart_read(&heart_regs->cause);
+	error_irqs = (pending & HEART_L4_INT_MASK & mask);
+
+	/* Bail if there's nothing to process (how did we get here, then?) */
+	if (unlikely(!error_irqs))
+		return;
+
+	/* Prevent any of the error IRQs from firing again. */
+	heart_write(mask & ~(pending), &heart_regs->imr[cpu]);
+
+	/* Ack all error IRQs. */
+	heart_write(HEART_L4_INT_MASK, &heart_regs->clear_isr);
+
+	/*
+	 * If we also have a cause value, then something happened, so loop
+	 * through the error IRQs and report a "heart attack" for each one
+	 * and print the value of the HEART cause register.  This is really
+	 * primitive right now, but it should hopefully work until a more
+	 * robust error handling routine can be put together.
+	 *
+	 * Refer to heart.h for the HC_* macros to work out the cause
+	 * that got us here.
+	 */
+	if (cause) {
+		pr_alert("IP30: CPU%d: HEART ATTACK! ISR = 0x%.16llx, IMR = 0x%.16llx, CAUSE = 0x%.16llx\n",
+			 cpu, pending, mask, cause);
+
+		if (cause & HC_COR_MEM_ERR) {
+			err_reg = heart_read(&heart_regs->mem_err_addr);
+			pr_alert("  HEART_MEMERR_ADDR = 0x%.16llx\n", err_reg);
+		}
+
+		/* i = 63; i >= 51; i-- */
+		for (i = HEART_ERR_MASK_END; i >= HEART_ERR_MASK_START; i--)
+			if ((pending >> i) & 1)
+				pr_alert("  HEART Error IRQ #%d\n", i);
+
+		/* XXX: Seems possible to loop forever here, so panic(). */
+		panic("IP30: Fatal Error !\n");
+	}
+
+	/* Unmask the error IRQs. */
+	heart_write(mask, &heart_regs->imr[cpu]);
+}
+
+static void ip30_normal_irq(struct irq_desc *desc)
+{
+	int cpu = smp_processor_id();
+	struct irq_domain *domain;
+	u64 pend, mask;
+	int ret;
+
+	pend = heart_read(&heart_regs->isr);
+	mask = (heart_read(&heart_regs->imr[cpu]) &
+		(HEART_L0_INT_MASK | HEART_L1_INT_MASK | HEART_L2_INT_MASK));
+
+	pend &= mask;
+	if (unlikely(!pend))
+		return;
+
+#ifdef CONFIG_SMP
+	if (pend & BIT_ULL(HEART_L2_INT_RESCHED_CPU_0)) {
+		heart_write(BIT_ULL(HEART_L2_INT_RESCHED_CPU_0),
+			    &heart_regs->clear_isr);
+		scheduler_ipi();
+	} else if (pend & BIT_ULL(HEART_L2_INT_RESCHED_CPU_1)) {
+		heart_write(BIT_ULL(HEART_L2_INT_RESCHED_CPU_1),
+			    &heart_regs->clear_isr);
+		scheduler_ipi();
+	} else if (pend & BIT_ULL(HEART_L2_INT_CALL_CPU_0)) {
+		heart_write(BIT_ULL(HEART_L2_INT_CALL_CPU_0),
+			    &heart_regs->clear_isr);
+		generic_smp_call_function_interrupt();
+	} else if (pend & BIT_ULL(HEART_L2_INT_CALL_CPU_1)) {
+		heart_write(BIT_ULL(HEART_L2_INT_CALL_CPU_1),
+			    &heart_regs->clear_isr);
+		generic_smp_call_function_interrupt();
+	} else
+#endif
+	{
+		domain = irq_desc_get_handler_data(desc);
+		ret = generic_handle_domain_irq(domain, __ffs(pend));
+		if (ret)
+			spurious_interrupt();
+	}
+}
+
+static void ip30_ack_heart_irq(struct irq_data *d)
+{
+	heart_write(BIT_ULL(d->hwirq), &heart_regs->clear_isr);
+}
+
+static void ip30_mask_heart_irq(struct irq_data *d)
+{
+	struct heart_irq_data *hd = irq_data_get_irq_chip_data(d);
+	unsigned long *mask = &per_cpu(irq_enable_mask, hd->cpu);
+
+	clear_bit(d->hwirq, mask);
+	heart_write(*mask, &heart_regs->imr[hd->cpu]);
+}
+
+static void ip30_mask_and_ack_heart_irq(struct irq_data *d)
+{
+	struct heart_irq_data *hd = irq_data_get_irq_chip_data(d);
+	unsigned long *mask = &per_cpu(irq_enable_mask, hd->cpu);
+
+	clear_bit(d->hwirq, mask);
+	heart_write(*mask, &heart_regs->imr[hd->cpu]);
+	heart_write(BIT_ULL(d->hwirq), &heart_regs->clear_isr);
+}
+
+static void ip30_unmask_heart_irq(struct irq_data *d)
+{
+	struct heart_irq_data *hd = irq_data_get_irq_chip_data(d);
+	unsigned long *mask = &per_cpu(irq_enable_mask, hd->cpu);
+
+	set_bit(d->hwirq, mask);
+	heart_write(*mask, &heart_regs->imr[hd->cpu]);
+}
+
+static int ip30_set_heart_irq_affinity(struct irq_data *d,
+				       const struct cpumask *mask, bool force)
+{
+	struct heart_irq_data *hd = irq_data_get_irq_chip_data(d);
+
+	if (!hd)
+		return -EINVAL;
+
+	if (irqd_is_started(d))
+		ip30_mask_and_ack_heart_irq(d);
+
+	hd->cpu = cpumask_first_and(mask, cpu_online_mask);
+
+	if (irqd_is_started(d))
+		ip30_unmask_heart_irq(d);
+
+	irq_data_update_effective_affinity(d, cpumask_of(hd->cpu));
+
+	return 0;
+}
+
+static struct irq_chip heart_irq_chip = {
+	.name			= "HEART",
+	.irq_ack		= ip30_ack_heart_irq,
+	.irq_mask		= ip30_mask_heart_irq,
+	.irq_mask_ack		= ip30_mask_and_ack_heart_irq,
+	.irq_unmask		= ip30_unmask_heart_irq,
+	.irq_set_affinity	= ip30_set_heart_irq_affinity,
+};
+
+static int heart_domain_alloc(struct irq_domain *domain, unsigned int virq,
+			      unsigned int nr_irqs, void *arg)
+{
+	struct irq_alloc_info *info = arg;
+	struct heart_irq_data *hd;
+	int hwirq;
+
+	if (nr_irqs > 1 || !info)
+		return -EINVAL;
+
+	hd = kzalloc(sizeof(*hd), GFP_KERNEL);
+	if (!hd)
+		return -ENOMEM;
+
+	hwirq = heart_alloc_int();
+	if (hwirq < 0) {
+		kfree(hd);
+		return -EAGAIN;
+	}
+	irq_domain_set_info(domain, virq, hwirq, &heart_irq_chip, hd,
+			    handle_level_irq, NULL, NULL);
+
+	return 0;
+}
+
+static void heart_domain_free(struct irq_domain *domain,
+			      unsigned int virq, unsigned int nr_irqs)
+{
+	struct irq_data *irqd;
+
+	if (nr_irqs > 1)
+		return;
+
+	irqd = irq_domain_get_irq_data(domain, virq);
+	if (irqd) {
+		clear_bit(irqd->hwirq, heart_irq_map);
+		kfree(irqd->chip_data);
+	}
+}
+
+static const struct irq_domain_ops heart_domain_ops = {
+	.alloc = heart_domain_alloc,
+	.free  = heart_domain_free,
+};
+
+void __init ip30_install_ipi(void)
+{
+	int cpu = smp_processor_id();
+	unsigned long *mask = &per_cpu(irq_enable_mask, cpu);
+
+	set_bit(HEART_L2_INT_RESCHED_CPU_0 + cpu, mask);
+	heart_write(BIT_ULL(HEART_L2_INT_RESCHED_CPU_0 + cpu),
+		    &heart_regs->clear_isr);
+	set_bit(HEART_L2_INT_CALL_CPU_0 + cpu, mask);
+	heart_write(BIT_ULL(HEART_L2_INT_CALL_CPU_0 + cpu),
+		    &heart_regs->clear_isr);
+
+	heart_write(*mask, &heart_regs->imr[cpu]);
+}
+
+void __init arch_init_irq(void)
+{
+	struct irq_domain *domain;
+	struct fwnode_handle *fn;
+	unsigned long *mask;
+	int i;
+
+	mips_cpu_irq_init();
+
+	/* Mask all IRQs. */
+	heart_write(HEART_CLR_ALL_MASK, &heart_regs->imr[0]);
+	heart_write(HEART_CLR_ALL_MASK, &heart_regs->imr[1]);
+	heart_write(HEART_CLR_ALL_MASK, &heart_regs->imr[2]);
+	heart_write(HEART_CLR_ALL_MASK, &heart_regs->imr[3]);
+
+	/* Ack everything. */
+	heart_write(HEART_ACK_ALL_MASK, &heart_regs->clear_isr);
+
+	/* Enable specific HEART error IRQs for each CPU. */
+	mask = &per_cpu(irq_enable_mask, 0);
+	*mask |= HEART_CPU0_ERR_MASK;
+	heart_write(*mask, &heart_regs->imr[0]);
+	mask = &per_cpu(irq_enable_mask, 1);
+	*mask |= HEART_CPU1_ERR_MASK;
+	heart_write(*mask, &heart_regs->imr[1]);
+
+	/*
+	 * Some HEART bits are reserved by hardware or by software convention.
+	 * Mark these as reserved right away so they won't be accidentally
+	 * used later.
+	 */
+	set_bit(HEART_L0_INT_GENERIC, heart_irq_map);
+	set_bit(HEART_L0_INT_FLOW_CTRL_HWTR_0, heart_irq_map);
+	set_bit(HEART_L0_INT_FLOW_CTRL_HWTR_1, heart_irq_map);
+	set_bit(HEART_L2_INT_RESCHED_CPU_0, heart_irq_map);
+	set_bit(HEART_L2_INT_RESCHED_CPU_1, heart_irq_map);
+	set_bit(HEART_L2_INT_CALL_CPU_0, heart_irq_map);
+	set_bit(HEART_L2_INT_CALL_CPU_1, heart_irq_map);
+	set_bit(HEART_L3_INT_TIMER, heart_irq_map);
+
+	/* Reserve the error interrupts (#51 to #63). */
+	for (i = HEART_L4_INT_XWID_ERR_9; i <= HEART_L4_INT_HEART_EXCP; i++)
+		set_bit(i, heart_irq_map);
+
+	fn = irq_domain_alloc_named_fwnode("HEART");
+	WARN_ON(fn == NULL);
+	if (!fn)
+		return;
+	domain = irq_domain_create_linear(fn, HEART_NUM_IRQS,
+					  &heart_domain_ops, NULL);
+	WARN_ON(domain == NULL);
+	if (!domain)
+		return;
+
+	irq_set_default_host(domain);
+
+	irq_set_percpu_devid(IP30_HEART_L0_IRQ);
+	irq_set_chained_handler_and_data(IP30_HEART_L0_IRQ, ip30_normal_irq,
+					 domain);
+	irq_set_percpu_devid(IP30_HEART_L1_IRQ);
+	irq_set_chained_handler_and_data(IP30_HEART_L1_IRQ, ip30_normal_irq,
+					 domain);
+	irq_set_percpu_devid(IP30_HEART_L2_IRQ);
+	irq_set_chained_handler_and_data(IP30_HEART_L2_IRQ, ip30_normal_irq,
+					 domain);
+	irq_set_percpu_devid(IP30_HEART_ERR_IRQ);
+	irq_set_chained_handler_and_data(IP30_HEART_ERR_IRQ, ip30_error_irq,
+					 domain);
+}
diff --git a/arch/mips/sgi-ip30/ip30-power.c b/arch/mips/sgi-ip30/ip30-power.c
new file mode 100644
index 000000000..120b3f3d5
--- /dev/null
+++ b/arch/mips/sgi-ip30/ip30-power.c
@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ip30-power.c: Software powerdown and reset handling for IP30 architecture.
+ *
+ * Copyright (C) 2004-2007 Stanislaw Skowronek <skylark@unaligned.org>
+ *               2014 Joshua Kinard <kumba@gentoo.org>
+ *               2009 Johannes Dickgreber <tanzy@gmx.de>
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/sched.h>
+#include <linux/notifier.h>
+#include <linux/delay.h>
+#include <linux/rtc/ds1685.h>
+#include <linux/interrupt.h>
+#include <linux/pm.h>
+
+#include <asm/reboot.h>
+#include <asm/sgi/heart.h>
+
+static void __noreturn ip30_machine_restart(char *cmd)
+{
+	/*
+	 * Execute HEART cold reset
+	 *   Yes, it's cold-HEARTed!
+	 */
+	heart_write((heart_read(&heart_regs->mode) | HM_COLD_RST),
+		    &heart_regs->mode);
+	unreachable();
+}
+
+static int __init ip30_reboot_setup(void)
+{
+	_machine_restart = ip30_machine_restart;
+
+	return 0;
+}
+
+subsys_initcall(ip30_reboot_setup);
diff --git a/arch/mips/sgi-ip30/ip30-setup.c b/arch/mips/sgi-ip30/ip30-setup.c
new file mode 100644
index 000000000..75a34684e
--- /dev/null
+++ b/arch/mips/sgi-ip30/ip30-setup.c
@@ -0,0 +1,138 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * SGI IP30 miscellaneous setup bits.
+ *
+ * Copyright (C) 2004-2007 Stanislaw Skowronek <skylark@unaligned.org>
+ *               2007 Joshua Kinard <kumba@gentoo.org>
+ *               2009 Johannes Dickgreber <tanzy@gmx.de>
+ */
+
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/percpu.h>
+#include <linux/memblock.h>
+
+#include <asm/smp-ops.h>
+#include <asm/sgialib.h>
+#include <asm/time.h>
+#include <asm/sgi/heart.h>
+
+#include "ip30-common.h"
+
+/* Structure of accessible HEART registers located in XKPHYS space. */
+struct ip30_heart_regs __iomem *heart_regs = HEART_XKPHYS_BASE;
+
+/*
+ * ARCS will report up to the first 1GB of
+ * memory if queried.  Anything beyond that
+ * is marked as reserved.
+ */
+#define IP30_MAX_PROM_MEMORY	_AC(0x40000000, UL)
+
+/*
+ * Memory in the Octane starts at 512MB
+ */
+#define IP30_MEMORY_BASE	_AC(0x20000000, UL)
+
+/*
+ * If using ARCS to probe for memory, then
+ * remaining memory will start at this offset.
+ */
+#define IP30_REAL_MEMORY_START  (IP30_MEMORY_BASE + IP30_MAX_PROM_MEMORY)
+
+#define MEM_SHIFT(x) ((x) >> 20)
+
+static void __init ip30_mem_init(void)
+{
+	unsigned long total_mem;
+	phys_addr_t addr;
+	phys_addr_t size;
+	u32 memcfg;
+	int i;
+
+	total_mem = 0;
+	for (i = 0; i < HEART_MEMORY_BANKS; i++) {
+		memcfg = __raw_readl(&heart_regs->mem_cfg.l[i]);
+		if (!(memcfg & HEART_MEMCFG_VALID))
+			continue;
+
+		addr = memcfg & HEART_MEMCFG_ADDR_MASK;
+		addr <<= HEART_MEMCFG_UNIT_SHIFT;
+		addr += IP30_MEMORY_BASE;
+		size = memcfg & HEART_MEMCFG_SIZE_MASK;
+		size >>= HEART_MEMCFG_SIZE_SHIFT;
+		size += 1;
+		size <<= HEART_MEMCFG_UNIT_SHIFT;
+
+		total_mem += size;
+
+		if (addr >= IP30_REAL_MEMORY_START)
+			memblock_phys_free(addr, size);
+		else if ((addr + size) > IP30_REAL_MEMORY_START)
+			memblock_phys_free(IP30_REAL_MEMORY_START,
+					   size - IP30_MAX_PROM_MEMORY);
+	}
+	pr_info("Detected %luMB of physical memory.\n", MEM_SHIFT(total_mem));
+}
+
+/**
+ * ip30_cpu_time_init - platform time initialization.
+ */
+static void __init ip30_cpu_time_init(void)
+{
+	int cpu = smp_processor_id();
+	u64 heart_compare;
+	unsigned int start, end;
+	int time_diff;
+
+	heart_compare = (heart_read(&heart_regs->count) +
+			 (HEART_CYCLES_PER_SEC / 10));
+	start = read_c0_count();
+	while ((heart_read(&heart_regs->count) - heart_compare) & 0x800000)
+		cpu_relax();
+
+	end = read_c0_count();
+	time_diff = (int)end - (int)start;
+	mips_hpt_frequency = time_diff * 10;
+	pr_info("IP30: CPU%d: %d MHz CPU detected.\n", cpu,
+		(mips_hpt_frequency * 2) / 1000000);
+}
+
+void __init ip30_per_cpu_init(void)
+{
+	/* Disable all interrupts. */
+	clear_c0_status(ST0_IM);
+
+	ip30_cpu_time_init();
+#ifdef CONFIG_SMP
+	ip30_install_ipi();
+#endif
+
+	enable_percpu_irq(IP30_HEART_L0_IRQ, IRQ_TYPE_NONE);
+	enable_percpu_irq(IP30_HEART_L1_IRQ, IRQ_TYPE_NONE);
+	enable_percpu_irq(IP30_HEART_L2_IRQ, IRQ_TYPE_NONE);
+	enable_percpu_irq(IP30_HEART_ERR_IRQ, IRQ_TYPE_NONE);
+}
+
+/**
+ * plat_mem_setup - despite the name, misc setup happens here.
+ */
+void __init plat_mem_setup(void)
+{
+	ip30_mem_init();
+
+	/* XXX: Hard lock on /sbin/init if this flag isn't specified. */
+	prom_flags |= PROM_FLAG_DONT_FREE_TEMP;
+
+#ifdef CONFIG_SMP
+	register_smp_ops(&ip30_smp_ops);
+#else
+	ip30_per_cpu_init();
+#endif
+
+	ioport_resource.start = 0;
+	ioport_resource.end = ~0UL;
+	set_io_port_base(IO_BASE);
+}
diff --git a/arch/mips/sgi-ip30/ip30-smp.c b/arch/mips/sgi-ip30/ip30-smp.c
new file mode 100644
index 000000000..4bfe65460
--- /dev/null
+++ b/arch/mips/sgi-ip30/ip30-smp.c
@@ -0,0 +1,149 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ip30-smp.c: SMP on IP30 architecture.
+ * Based off of the original IP30 SMP code, with inspiration from ip27-smp.c
+ * and smp-bmips.c.
+ *
+ * Copyright (C) 2005-2007 Stanislaw Skowronek <skylark@unaligned.org>
+ *               2006-2007, 2014-2015 Joshua Kinard <kumba@gentoo.org>
+ *               2009 Johannes Dickgreber <tanzy@gmx.de>
+ */
+
+#include <linux/init.h>
+#include <linux/sched.h>
+#include <linux/sched/task_stack.h>
+
+#include <asm/time.h>
+#include <asm/sgi/heart.h>
+
+#include "ip30-common.h"
+
+#define MPCONF_MAGIC	0xbaddeed2
+#define	MPCONF_ADDR	0xa800000000000600L
+#define MPCONF_SIZE	0x80
+#define MPCONF(x)	(MPCONF_ADDR + (x) * MPCONF_SIZE)
+
+/* HEART can theoretically do 4 CPUs, but only 2 are physically possible */
+#define MP_NCPU		2
+
+struct mpconf {
+	u32 magic;
+	u32 prid;
+	u32 physid;
+	u32 virtid;
+	u32 scachesz;
+	u16 fanloads;
+	u16 res;
+	void *launch;
+	void *rendezvous;
+	u64 res2[3];
+	void *stackaddr;
+	void *lnch_parm;
+	void *rndv_parm;
+	u32 idleflag;
+};
+
+static void ip30_smp_send_ipi_single(int cpu, u32 action)
+{
+	int irq;
+
+	switch (action) {
+	case SMP_RESCHEDULE_YOURSELF:
+		irq = HEART_L2_INT_RESCHED_CPU_0;
+		break;
+	case SMP_CALL_FUNCTION:
+		irq = HEART_L2_INT_CALL_CPU_0;
+		break;
+	default:
+		panic("IP30: Unknown action value in %s!\n", __func__);
+	}
+
+	irq += cpu;
+
+	/* Poke the other CPU -- it's got mail! */
+	heart_write(BIT_ULL(irq), &heart_regs->set_isr);
+}
+
+static void ip30_smp_send_ipi_mask(const struct cpumask *mask, u32 action)
+{
+	u32 i;
+
+	for_each_cpu(i, mask)
+		ip30_smp_send_ipi_single(i, action);
+}
+
+static void __init ip30_smp_setup(void)
+{
+	int i;
+	int ncpu = 0;
+	struct mpconf *mpc;
+
+	init_cpu_possible(cpumask_of(0));
+
+	/* Scan the MPCONF structure and enumerate available CPUs. */
+	for (i = 0; i < MP_NCPU; i++) {
+		mpc = (struct mpconf *)MPCONF(i);
+		if (mpc->magic == MPCONF_MAGIC) {
+			set_cpu_possible(i, true);
+			__cpu_number_map[i] = ++ncpu;
+			__cpu_logical_map[ncpu] = i;
+			pr_info("IP30: Slot: %d, PrID: %.8x, PhyID: %d, VirtID: %d\n",
+				i, mpc->prid, mpc->physid, mpc->virtid);
+		}
+	}
+	pr_info("IP30: Detected %d CPU(s) present.\n", ncpu);
+
+	/*
+	 * Set the coherency algorithm to '5' (cacheable coherent
+	 * exclusive on write).  This is needed on IP30 SMP, especially
+	 * for R14000 CPUs, otherwise, instruction bus errors will
+	 * occur upon reaching userland.
+	 */
+	change_c0_config(CONF_CM_CMASK, CONF_CM_CACHABLE_COW);
+}
+
+static void __init ip30_smp_prepare_cpus(unsigned int max_cpus)
+{
+	/* nothing to do here */
+}
+
+static int __init ip30_smp_boot_secondary(int cpu, struct task_struct *idle)
+{
+	struct mpconf *mpc = (struct mpconf *)MPCONF(cpu);
+
+	/* Stack pointer (sp). */
+	mpc->stackaddr = (void *)__KSTK_TOS(idle);
+
+	/* Global pointer (gp). */
+	mpc->lnch_parm = task_thread_info(idle);
+
+	mb(); /* make sure stack and lparm are written */
+
+	/* Boot CPUx. */
+	mpc->launch = smp_bootstrap;
+
+	/* CPUx now executes smp_bootstrap, then ip30_smp_finish */
+	return 0;
+}
+
+static void __init ip30_smp_init_cpu(void)
+{
+	ip30_per_cpu_init();
+}
+
+static void __init ip30_smp_finish(void)
+{
+	enable_percpu_irq(get_c0_compare_int(), IRQ_TYPE_NONE);
+	local_irq_enable();
+}
+
+struct plat_smp_ops __read_mostly ip30_smp_ops = {
+	.send_ipi_single	= ip30_smp_send_ipi_single,
+	.send_ipi_mask		= ip30_smp_send_ipi_mask,
+	.smp_setup		= ip30_smp_setup,
+	.prepare_cpus		= ip30_smp_prepare_cpus,
+	.boot_secondary		= ip30_smp_boot_secondary,
+	.init_secondary		= ip30_smp_init_cpu,
+	.smp_finish		= ip30_smp_finish,
+	.prepare_boot_cpu	= ip30_smp_init_cpu,
+};
diff --git a/arch/mips/sgi-ip30/ip30-timer.c b/arch/mips/sgi-ip30/ip30-timer.c
new file mode 100644
index 000000000..d13e10547
--- /dev/null
+++ b/arch/mips/sgi-ip30/ip30-timer.c
@@ -0,0 +1,63 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ip30-timer.c: Clocksource/clockevent support for the
+ *               HEART chip in SGI Octane (IP30) systems.
+ *
+ * Copyright (C) 2004-2007 Stanislaw Skowronek <skylark@unaligned.org>
+ * Copyright (C) 2009 Johannes Dickgreber <tanzy@gmx.de>
+ * Copyright (C) 2011 Joshua Kinard <kumba@gentoo.org>
+ */
+
+#include <linux/clocksource.h>
+#include <linux/cpumask.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/percpu.h>
+#include <linux/sched_clock.h>
+
+#include <asm/time.h>
+#include <asm/cevt-r4k.h>
+#include <asm/sgi/heart.h>
+
+static u64 ip30_heart_counter_read(struct clocksource *cs)
+{
+	return heart_read(&heart_regs->count);
+}
+
+struct clocksource ip30_heart_clocksource = {
+	.name	= "HEART",
+	.rating	= 400,
+	.read	= ip30_heart_counter_read,
+	.mask	= CLOCKSOURCE_MASK(52),
+	.flags	= (CLOCK_SOURCE_IS_CONTINUOUS | CLOCK_SOURCE_VALID_FOR_HRES),
+};
+
+static u64 notrace ip30_heart_read_sched_clock(void)
+{
+	return heart_read(&heart_regs->count);
+}
+
+static void __init ip30_heart_clocksource_init(void)
+{
+	struct clocksource *cs = &ip30_heart_clocksource;
+
+	clocksource_register_hz(cs, HEART_CYCLES_PER_SEC);
+
+	sched_clock_register(ip30_heart_read_sched_clock, 52,
+			     HEART_CYCLES_PER_SEC);
+}
+
+void __init plat_time_init(void)
+{
+	int irq = get_c0_compare_int();
+
+	cp0_timer_irq_installed = 1;
+	c0_compare_irqaction.percpu_dev_id = &mips_clockevent_device;
+	c0_compare_irqaction.flags &= ~IRQF_SHARED;
+	irq_set_handler(irq, handle_percpu_devid_irq);
+	irq_set_percpu_devid(irq);
+	setup_percpu_irq(irq, &c0_compare_irqaction);
+	enable_percpu_irq(irq, IRQ_TYPE_NONE);
+
+	ip30_heart_clocksource_init();
+}
diff --git a/arch/mips/sgi-ip30/ip30-xtalk.c b/arch/mips/sgi-ip30/ip30-xtalk.c
new file mode 100644
index 000000000..7ceb2b23e
--- /dev/null
+++ b/arch/mips/sgi-ip30/ip30-xtalk.c
@@ -0,0 +1,186 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ip30-xtalk.c - Very basic Crosstalk (XIO) detection support.
+ *   Copyright (C) 2004-2007 Stanislaw Skowronek <skylark@unaligned.org>
+ *   Copyright (C) 2009 Johannes Dickgreber <tanzy@gmx.de>
+ *   Copyright (C) 2007, 2014-2016 Joshua Kinard <kumba@gentoo.org>
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/platform_data/sgi-w1.h>
+#include <linux/platform_data/xtalk-bridge.h>
+
+#include <asm/xtalk/xwidget.h>
+#include <asm/pci/bridge.h>
+
+#define IP30_SWIN_BASE(widget) \
+		(0x0000000010000000 | (((unsigned long)(widget)) << 24))
+
+#define IP30_RAW_SWIN_BASE(widget)	(IO_BASE + IP30_SWIN_BASE(widget))
+
+#define IP30_SWIN_SIZE		(1 << 24)
+
+#define IP30_WIDGET_XBOW        _AC(0x0, UL)    /* XBow is always 0 */
+#define IP30_WIDGET_HEART       _AC(0x8, UL)    /* HEART is always 8 */
+#define IP30_WIDGET_PCI_BASE    _AC(0xf, UL)    /* BaseIO PCI is always 15 */
+
+#define XTALK_NODEV             0xffffffff
+
+#define XBOW_REG_LINK_STAT_0    0x114
+#define XBOW_REG_LINK_BLK_SIZE  0x40
+#define XBOW_REG_LINK_ALIVE     0x80000000
+
+#define HEART_INTR_ADDR		0x00000080
+
+#define xtalk_read	__raw_readl
+
+static void bridge_platform_create(int widget, int masterwid)
+{
+	struct xtalk_bridge_platform_data *bd;
+	struct sgi_w1_platform_data *wd;
+	struct platform_device *pdev_wd;
+	struct platform_device *pdev_bd;
+	struct resource w1_res;
+
+	wd = kzalloc(sizeof(*wd), GFP_KERNEL);
+	if (!wd) {
+		pr_warn("xtalk:%x bridge create out of memory\n", widget);
+		return;
+	}
+
+	snprintf(wd->dev_id, sizeof(wd->dev_id), "bridge-%012lx",
+		 IP30_SWIN_BASE(widget));
+
+	memset(&w1_res, 0, sizeof(w1_res));
+	w1_res.start = IP30_SWIN_BASE(widget) +
+				offsetof(struct bridge_regs, b_nic);
+	w1_res.end = w1_res.start + 3;
+	w1_res.flags = IORESOURCE_MEM;
+
+	pdev_wd = platform_device_alloc("sgi_w1", PLATFORM_DEVID_AUTO);
+	if (!pdev_wd) {
+		pr_warn("xtalk:%x bridge create out of memory\n", widget);
+		goto err_kfree_wd;
+	}
+	if (platform_device_add_resources(pdev_wd, &w1_res, 1)) {
+		pr_warn("xtalk:%x bridge failed to add platform resources.\n", widget);
+		goto err_put_pdev_wd;
+	}
+	if (platform_device_add_data(pdev_wd, wd, sizeof(*wd))) {
+		pr_warn("xtalk:%x bridge failed to add platform data.\n", widget);
+		goto err_put_pdev_wd;
+	}
+	if (platform_device_add(pdev_wd)) {
+		pr_warn("xtalk:%x bridge failed to add platform device.\n", widget);
+		goto err_put_pdev_wd;
+	}
+	/* platform_device_add_data() duplicates the data */
+	kfree(wd);
+
+	bd = kzalloc(sizeof(*bd), GFP_KERNEL);
+	if (!bd) {
+		pr_warn("xtalk:%x bridge create out of memory\n", widget);
+		goto err_unregister_pdev_wd;
+	}
+	pdev_bd = platform_device_alloc("xtalk-bridge", PLATFORM_DEVID_AUTO);
+	if (!pdev_bd) {
+		pr_warn("xtalk:%x bridge create out of memory\n", widget);
+		goto err_kfree_bd;
+	}
+
+	bd->bridge_addr	= IP30_RAW_SWIN_BASE(widget);
+	bd->intr_addr	= HEART_INTR_ADDR;
+	bd->nasid	= 0;
+	bd->masterwid	= masterwid;
+
+	bd->mem.name	= "Bridge PCI MEM";
+	bd->mem.start	= IP30_SWIN_BASE(widget) + BRIDGE_DEVIO0;
+	bd->mem.end	= IP30_SWIN_BASE(widget) + IP30_SWIN_SIZE - 1;
+	bd->mem.flags	= IORESOURCE_MEM;
+	bd->mem_offset	= IP30_SWIN_BASE(widget);
+
+	bd->io.name	= "Bridge PCI IO";
+	bd->io.start	= IP30_SWIN_BASE(widget) + BRIDGE_DEVIO0;
+	bd->io.end	= IP30_SWIN_BASE(widget) + IP30_SWIN_SIZE - 1;
+	bd->io.flags	= IORESOURCE_IO;
+	bd->io_offset	= IP30_SWIN_BASE(widget);
+
+	if (platform_device_add_data(pdev_bd, bd, sizeof(*bd))) {
+		pr_warn("xtalk:%x bridge failed to add platform data.\n", widget);
+		goto err_put_pdev_bd;
+	}
+	if (platform_device_add(pdev_bd)) {
+		pr_warn("xtalk:%x bridge failed to add platform device.\n", widget);
+		goto err_put_pdev_bd;
+	}
+	/* platform_device_add_data() duplicates the data */
+	kfree(bd);
+	pr_info("xtalk:%x bridge widget\n", widget);
+	return;
+
+err_put_pdev_bd:
+	platform_device_put(pdev_bd);
+err_kfree_bd:
+	kfree(bd);
+err_unregister_pdev_wd:
+	platform_device_unregister(pdev_wd);
+	return;
+err_put_pdev_wd:
+	platform_device_put(pdev_wd);
+err_kfree_wd:
+	kfree(wd);
+	return;
+}
+
+static unsigned int __init xbow_widget_active(s8 wid)
+{
+	unsigned int link_stat;
+
+	link_stat = xtalk_read((void *)(IP30_RAW_SWIN_BASE(IP30_WIDGET_XBOW) +
+					XBOW_REG_LINK_STAT_0 +
+					XBOW_REG_LINK_BLK_SIZE *
+					(wid - 8)));
+
+	return (link_stat & XBOW_REG_LINK_ALIVE) ? 1 : 0;
+}
+
+static void __init xtalk_init_widget(s8 wid, s8 masterwid)
+{
+	xwidget_part_num_t partnum;
+	widgetreg_t widget_id;
+
+	if (!xbow_widget_active(wid))
+		return;
+
+	widget_id = xtalk_read((void *)(IP30_RAW_SWIN_BASE(wid) + WIDGET_ID));
+
+	partnum = XWIDGET_PART_NUM(widget_id);
+
+	switch (partnum) {
+	case BRIDGE_WIDGET_PART_NUM:
+	case XBRIDGE_WIDGET_PART_NUM:
+		bridge_platform_create(wid, masterwid);
+		break;
+	default:
+		pr_info("xtalk:%x unknown widget (0x%x)\n", wid, partnum);
+		break;
+	}
+}
+
+static int __init ip30_xtalk_init(void)
+{
+	int i;
+
+	/*
+	 * Walk widget IDs backwards so that BaseIO is probed first.  This
+	 * ensures that the BaseIO IOC3 is always detected as eth0.
+	 */
+	for (i = IP30_WIDGET_PCI_BASE; i > IP30_WIDGET_HEART; i--)
+		xtalk_init_widget(i, IP30_WIDGET_HEART);
+
+	return 0;
+}
+
+arch_initcall(ip30_xtalk_init);
diff --git a/arch/mips/sgi-ip32/Makefile b/arch/mips/sgi-ip32/Makefile
new file mode 100644
index 000000000..de0222466
--- /dev/null
+++ b/arch/mips/sgi-ip32/Makefile
@@ -0,0 +1,8 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Makefile for the SGI specific kernel interface routines
+# under Linux.
+#
+
+obj-y	+= ip32-berr.o ip32-irq.o ip32-platform.o ip32-setup.o ip32-reset.o \
+	   crime.o ip32-memory.o ip32-dma.o
diff --git a/arch/mips/sgi-ip32/Platform b/arch/mips/sgi-ip32/Platform
new file mode 100644
index 000000000..f58a7a02b
--- /dev/null
+++ b/arch/mips/sgi-ip32/Platform
@@ -0,0 +1,10 @@
+#
+# SGI-IP32 (O2)
+#
+# Set the load address to >= 80069000 if you want to leave space for symmon,
+# 0xffffffff80004000 for production kernels.  Note that the value must be aligned to
+# a multiple of the kernel stack size or the handling of the current variable
+# will break.
+#
+cflags-$(CONFIG_SGI_IP32)	+= -I$(srctree)/arch/mips/include/asm/mach-ip32
+load-$(CONFIG_SGI_IP32)		+= 0xffffffff80004000
diff --git a/arch/mips/sgi-ip32/crime.c b/arch/mips/sgi-ip32/crime.c
new file mode 100644
index 000000000..a8e0c776c
--- /dev/null
+++ b/arch/mips/sgi-ip32/crime.c
@@ -0,0 +1,103 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2001, 2003 Keith M Wesolowski
+ * Copyright (C) 2005 Ilya A. Volynets <ilya@total-knowledge.com>
+ */
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/interrupt.h>
+#include <linux/export.h>
+#include <asm/bootinfo.h>
+#include <asm/io.h>
+#include <asm/mipsregs.h>
+#include <asm/page.h>
+#include <asm/ip32/crime.h>
+#include <asm/ip32/mace.h>
+
+struct sgi_crime __iomem *crime;
+struct sgi_mace __iomem *mace;
+
+EXPORT_SYMBOL_GPL(mace);
+
+void __init crime_init(void)
+{
+	unsigned int id, rev;
+	const int field = 2 * sizeof(unsigned long);
+
+	set_io_port_base((unsigned long) ioremap(MACEPCI_LOW_IO, 0x2000000));
+	crime = ioremap(CRIME_BASE, sizeof(struct sgi_crime));
+	mace = ioremap(MACE_BASE, sizeof(struct sgi_mace));
+
+	id = crime->id;
+	rev = id & CRIME_ID_REV;
+	id = (id & CRIME_ID_IDBITS) >> 4;
+	printk(KERN_INFO "CRIME id %1x rev %d at 0x%0*lx\n",
+	       id, rev, field, (unsigned long) CRIME_BASE);
+}
+
+irqreturn_t crime_memerr_intr(unsigned int irq, void *dev_id)
+{
+	unsigned long stat, addr;
+	int fatal = 0;
+
+	stat = crime->mem_error_stat & CRIME_MEM_ERROR_STAT_MASK;
+	addr = crime->mem_error_addr & CRIME_MEM_ERROR_ADDR_MASK;
+
+	printk("CRIME memory error at 0x%08lx ST 0x%08lx<", addr, stat);
+
+	if (stat & CRIME_MEM_ERROR_INV)
+		printk("INV,");
+	if (stat & CRIME_MEM_ERROR_ECC) {
+		unsigned long ecc_syn =
+			crime->mem_ecc_syn & CRIME_MEM_ERROR_ECC_SYN_MASK;
+		unsigned long ecc_gen =
+			crime->mem_ecc_chk & CRIME_MEM_ERROR_ECC_CHK_MASK;
+		printk("ECC,SYN=0x%08lx,GEN=0x%08lx,", ecc_syn, ecc_gen);
+	}
+	if (stat & CRIME_MEM_ERROR_MULTIPLE) {
+		fatal = 1;
+		printk("MULTIPLE,");
+	}
+	if (stat & CRIME_MEM_ERROR_HARD_ERR) {
+		fatal = 1;
+		printk("HARD,");
+	}
+	if (stat & CRIME_MEM_ERROR_SOFT_ERR)
+		printk("SOFT,");
+	if (stat & CRIME_MEM_ERROR_CPU_ACCESS)
+		printk("CPU,");
+	if (stat & CRIME_MEM_ERROR_VICE_ACCESS)
+		printk("VICE,");
+	if (stat & CRIME_MEM_ERROR_GBE_ACCESS)
+		printk("GBE,");
+	if (stat & CRIME_MEM_ERROR_RE_ACCESS)
+		printk("RE,REID=0x%02lx,", (stat & CRIME_MEM_ERROR_RE_ID)>>8);
+	if (stat & CRIME_MEM_ERROR_MACE_ACCESS)
+		printk("MACE,MACEID=0x%02lx,", stat & CRIME_MEM_ERROR_MACE_ID);
+
+	crime->mem_error_stat = 0;
+
+	if (fatal) {
+		printk("FATAL>\n");
+		panic("Fatal memory error.");
+	} else
+		printk("NONFATAL>\n");
+
+	return IRQ_HANDLED;
+}
+
+irqreturn_t crime_cpuerr_intr(unsigned int irq, void *dev_id)
+{
+	unsigned long stat = crime->cpu_error_stat & CRIME_CPU_ERROR_MASK;
+	unsigned long addr = crime->cpu_error_addr & CRIME_CPU_ERROR_ADDR_MASK;
+
+	addr <<= 2;
+	printk("CRIME CPU error at 0x%09lx status 0x%08lx\n", addr, stat);
+	crime->cpu_error_stat = 0;
+
+	return IRQ_HANDLED;
+}
diff --git a/arch/mips/sgi-ip32/ip32-berr.c b/arch/mips/sgi-ip32/ip32-berr.c
new file mode 100644
index 000000000..478b63b4c
--- /dev/null
+++ b/arch/mips/sgi-ip32/ip32-berr.c
@@ -0,0 +1,38 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994, 1995, 1996, 1999, 2000 by Ralf Baechle
+ * Copyright (C) 1999, 2000 by Silicon Graphics
+ * Copyright (C) 2002  Maciej W. Rozycki
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/sched/debug.h>
+#include <linux/sched/signal.h>
+#include <asm/traps.h>
+#include <linux/uaccess.h>
+#include <asm/addrspace.h>
+#include <asm/ptrace.h>
+#include <asm/tlbdebug.h>
+
+static int ip32_be_handler(struct pt_regs *regs, int is_fixup)
+{
+	int data = regs->cp0_cause & 4;
+
+	if (is_fixup)
+		return MIPS_BE_FIXUP;
+
+	printk("Got %cbe at 0x%lx\n", data ? 'd' : 'i', regs->cp0_epc);
+	show_regs(regs);
+	dump_tlb_all();
+	while(1);
+	force_sig(SIGBUS);
+}
+
+void __init ip32_be_init(void)
+{
+	mips_set_be_handler(ip32_be_handler);
+}
diff --git a/arch/mips/sgi-ip32/ip32-dma.c b/arch/mips/sgi-ip32/ip32-dma.c
new file mode 100644
index 000000000..20c6da9d7
--- /dev/null
+++ b/arch/mips/sgi-ip32/ip32-dma.c
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2006  Ralf Baechle <ralf@linux-mips.org>
+ */
+#include <linux/dma-direct.h>
+#include <asm/ip32/crime.h>
+
+/*
+ * Few notes.
+ * 1. CPU sees memory as two chunks: 0-256M@0x0, and the rest @0x40000000+256M
+ * 2. PCI sees memory as one big chunk @0x0 (or we could use 0x40000000 for
+ *    native-endian)
+ * 3. All other devices see memory as one big chunk at 0x40000000
+ * 4. Non-PCI devices will pass NULL as struct device*
+ *
+ * Thus we translate differently, depending on device.
+ */
+
+#define RAM_OFFSET_MASK 0x3fffffffUL
+
+dma_addr_t phys_to_dma(struct device *dev, phys_addr_t paddr)
+{
+	dma_addr_t dma_addr = paddr & RAM_OFFSET_MASK;
+
+	if (!dev)
+		dma_addr += CRIME_HI_MEM_BASE;
+	return dma_addr;
+}
+
+phys_addr_t dma_to_phys(struct device *dev, dma_addr_t dma_addr)
+{
+	phys_addr_t paddr = dma_addr & RAM_OFFSET_MASK;
+
+	if (dma_addr >= 256*1024*1024)
+		paddr += CRIME_HI_MEM_BASE;
+	return paddr;
+}
diff --git a/arch/mips/sgi-ip32/ip32-irq.c b/arch/mips/sgi-ip32/ip32-irq.c
new file mode 100644
index 000000000..e21ea1de0
--- /dev/null
+++ b/arch/mips/sgi-ip32/ip32-irq.c
@@ -0,0 +1,499 @@
+/*
+ * Code to handle IP32 IRQs
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2000 Harald Koerfgen
+ * Copyright (C) 2001 Keith M Wesolowski
+ */
+#include <linux/init.h>
+#include <linux/kernel_stat.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/bitops.h>
+#include <linux/kernel.h>
+#include <linux/mm.h>
+#include <linux/random.h>
+#include <linux/sched.h>
+#include <linux/sched/debug.h>
+
+#include <asm/irq_cpu.h>
+#include <asm/mipsregs.h>
+#include <asm/signal.h>
+#include <asm/time.h>
+#include <asm/ip32/crime.h>
+#include <asm/ip32/mace.h>
+#include <asm/ip32/ip32_ints.h>
+
+/* issue a PIO read to make sure no PIO writes are pending */
+static inline void flush_crime_bus(void)
+{
+	crime->control;
+}
+
+static inline void flush_mace_bus(void)
+{
+	mace->perif.ctrl.misc;
+}
+
+/*
+ * O2 irq map
+ *
+ * IP0 -> software (ignored)
+ * IP1 -> software (ignored)
+ * IP2 -> (irq0) C crime 1.1 all interrupts; crime 1.5 ???
+ * IP3 -> (irq1) X unknown
+ * IP4 -> (irq2) X unknown
+ * IP5 -> (irq3) X unknown
+ * IP6 -> (irq4) X unknown
+ * IP7 -> (irq5) 7 CPU count/compare timer (system timer)
+ *
+ * crime: (C)
+ *
+ * CRIME_INT_STAT 31:0:
+ *
+ * 0  ->  8  Video in 1
+ * 1  ->  9 Video in 2
+ * 2  -> 10  Video out
+ * 3  -> 11  Mace ethernet
+ * 4  -> S  SuperIO sub-interrupt
+ * 5  -> M  Miscellaneous sub-interrupt
+ * 6  -> A  Audio sub-interrupt
+ * 7  -> 15  PCI bridge errors
+ * 8  -> 16  PCI SCSI aic7xxx 0
+ * 9  -> 17 PCI SCSI aic7xxx 1
+ * 10 -> 18 PCI slot 0
+ * 11 -> 19 unused (PCI slot 1)
+ * 12 -> 20 unused (PCI slot 2)
+ * 13 -> 21 unused (PCI shared 0)
+ * 14 -> 22 unused (PCI shared 1)
+ * 15 -> 23 unused (PCI shared 2)
+ * 16 -> 24 GBE0 (E)
+ * 17 -> 25 GBE1 (E)
+ * 18 -> 26 GBE2 (E)
+ * 19 -> 27 GBE3 (E)
+ * 20 -> 28 CPU errors
+ * 21 -> 29 Memory errors
+ * 22 -> 30 RE empty edge (E)
+ * 23 -> 31 RE full edge (E)
+ * 24 -> 32 RE idle edge (E)
+ * 25 -> 33 RE empty level
+ * 26 -> 34 RE full level
+ * 27 -> 35 RE idle level
+ * 28 -> 36 unused (software 0) (E)
+ * 29 -> 37 unused (software 1) (E)
+ * 30 -> 38 unused (software 2) - crime 1.5 CPU SysCorError (E)
+ * 31 -> 39 VICE
+ *
+ * S, M, A: Use the MACE ISA interrupt register
+ * MACE_ISA_INT_STAT 31:0
+ *
+ * 0-7 -> 40-47 Audio
+ * 8 -> 48 RTC
+ * 9 -> 49 Keyboard
+ * 10 -> X Keyboard polled
+ * 11 -> 51 Mouse
+ * 12 -> X Mouse polled
+ * 13-15 -> 53-55 Count/compare timers
+ * 16-19 -> 56-59 Parallel (16 E)
+ * 20-25 -> 60-62 Serial 1 (22 E)
+ * 26-31 -> 66-71 Serial 2 (28 E)
+ *
+ * Note that this means IRQs 12-14, 50, and 52 do not exist.  This is a
+ * different IRQ map than IRIX uses, but that's OK as Linux irq handling
+ * is quite different anyway.
+ */
+
+/* Some initial interrupts to set up */
+extern irqreturn_t crime_memerr_intr(int irq, void *dev_id);
+extern irqreturn_t crime_cpuerr_intr(int irq, void *dev_id);
+
+/*
+ * This is for pure CRIME interrupts - ie not MACE.  The advantage?
+ * We get to split the register in half and do faster lookups.
+ */
+
+static uint64_t crime_mask;
+
+static inline void crime_enable_irq(struct irq_data *d)
+{
+	unsigned int bit = d->irq - CRIME_IRQ_BASE;
+
+	crime_mask |= 1 << bit;
+	crime->imask = crime_mask;
+}
+
+static inline void crime_disable_irq(struct irq_data *d)
+{
+	unsigned int bit = d->irq - CRIME_IRQ_BASE;
+
+	crime_mask &= ~(1 << bit);
+	crime->imask = crime_mask;
+	flush_crime_bus();
+}
+
+static struct irq_chip crime_level_interrupt = {
+	.name		= "IP32 CRIME",
+	.irq_mask	= crime_disable_irq,
+	.irq_unmask	= crime_enable_irq,
+};
+
+static void crime_edge_mask_and_ack_irq(struct irq_data *d)
+{
+	unsigned int bit = d->irq - CRIME_IRQ_BASE;
+	uint64_t crime_int;
+
+	/* Edge triggered interrupts must be cleared. */
+	crime_int = crime->hard_int;
+	crime_int &= ~(1 << bit);
+	crime->hard_int = crime_int;
+
+	crime_disable_irq(d);
+}
+
+static struct irq_chip crime_edge_interrupt = {
+	.name		= "IP32 CRIME",
+	.irq_ack	= crime_edge_mask_and_ack_irq,
+	.irq_mask	= crime_disable_irq,
+	.irq_mask_ack	= crime_edge_mask_and_ack_irq,
+	.irq_unmask	= crime_enable_irq,
+};
+
+/*
+ * This is for MACE PCI interrupts.  We can decrease bus traffic by masking
+ * as close to the source as possible.	This also means we can take the
+ * next chunk of the CRIME register in one piece.
+ */
+
+static unsigned long macepci_mask;
+
+static void enable_macepci_irq(struct irq_data *d)
+{
+	macepci_mask |= MACEPCI_CONTROL_INT(d->irq - MACEPCI_SCSI0_IRQ);
+	mace->pci.control = macepci_mask;
+	crime_mask |= 1 << (d->irq - CRIME_IRQ_BASE);
+	crime->imask = crime_mask;
+}
+
+static void disable_macepci_irq(struct irq_data *d)
+{
+	crime_mask &= ~(1 << (d->irq - CRIME_IRQ_BASE));
+	crime->imask = crime_mask;
+	flush_crime_bus();
+	macepci_mask &= ~MACEPCI_CONTROL_INT(d->irq - MACEPCI_SCSI0_IRQ);
+	mace->pci.control = macepci_mask;
+	flush_mace_bus();
+}
+
+static struct irq_chip ip32_macepci_interrupt = {
+	.name = "IP32 MACE PCI",
+	.irq_mask = disable_macepci_irq,
+	.irq_unmask = enable_macepci_irq,
+};
+
+/* This is used for MACE ISA interrupts.  That means bits 4-6 in the
+ * CRIME register.
+ */
+
+#define MACEISA_AUDIO_INT	(MACEISA_AUDIO_SW_INT |		\
+				 MACEISA_AUDIO_SC_INT |		\
+				 MACEISA_AUDIO1_DMAT_INT |	\
+				 MACEISA_AUDIO1_OF_INT |	\
+				 MACEISA_AUDIO2_DMAT_INT |	\
+				 MACEISA_AUDIO2_MERR_INT |	\
+				 MACEISA_AUDIO3_DMAT_INT |	\
+				 MACEISA_AUDIO3_MERR_INT)
+#define MACEISA_MISC_INT	(MACEISA_RTC_INT |		\
+				 MACEISA_KEYB_INT |		\
+				 MACEISA_KEYB_POLL_INT |	\
+				 MACEISA_MOUSE_INT |		\
+				 MACEISA_MOUSE_POLL_INT |	\
+				 MACEISA_TIMER0_INT |		\
+				 MACEISA_TIMER1_INT |		\
+				 MACEISA_TIMER2_INT)
+#define MACEISA_SUPERIO_INT	(MACEISA_PARALLEL_INT |		\
+				 MACEISA_PAR_CTXA_INT |		\
+				 MACEISA_PAR_CTXB_INT |		\
+				 MACEISA_PAR_MERR_INT |		\
+				 MACEISA_SERIAL1_INT |		\
+				 MACEISA_SERIAL1_TDMAT_INT |	\
+				 MACEISA_SERIAL1_TDMAPR_INT |	\
+				 MACEISA_SERIAL1_TDMAME_INT |	\
+				 MACEISA_SERIAL1_RDMAT_INT |	\
+				 MACEISA_SERIAL1_RDMAOR_INT |	\
+				 MACEISA_SERIAL2_INT |		\
+				 MACEISA_SERIAL2_TDMAT_INT |	\
+				 MACEISA_SERIAL2_TDMAPR_INT |	\
+				 MACEISA_SERIAL2_TDMAME_INT |	\
+				 MACEISA_SERIAL2_RDMAT_INT |	\
+				 MACEISA_SERIAL2_RDMAOR_INT)
+
+static unsigned long maceisa_mask;
+
+static void enable_maceisa_irq(struct irq_data *d)
+{
+	unsigned int crime_int = 0;
+
+	pr_debug("maceisa enable: %u\n", d->irq);
+
+	switch (d->irq) {
+	case MACEISA_AUDIO_SW_IRQ ... MACEISA_AUDIO3_MERR_IRQ:
+		crime_int = MACE_AUDIO_INT;
+		break;
+	case MACEISA_RTC_IRQ ... MACEISA_TIMER2_IRQ:
+		crime_int = MACE_MISC_INT;
+		break;
+	case MACEISA_PARALLEL_IRQ ... MACEISA_SERIAL2_RDMAOR_IRQ:
+		crime_int = MACE_SUPERIO_INT;
+		break;
+	}
+	pr_debug("crime_int %08x enabled\n", crime_int);
+	crime_mask |= crime_int;
+	crime->imask = crime_mask;
+	maceisa_mask |= 1 << (d->irq - MACEISA_AUDIO_SW_IRQ);
+	mace->perif.ctrl.imask = maceisa_mask;
+}
+
+static void disable_maceisa_irq(struct irq_data *d)
+{
+	unsigned int crime_int = 0;
+
+	maceisa_mask &= ~(1 << (d->irq - MACEISA_AUDIO_SW_IRQ));
+	if (!(maceisa_mask & MACEISA_AUDIO_INT))
+		crime_int |= MACE_AUDIO_INT;
+	if (!(maceisa_mask & MACEISA_MISC_INT))
+		crime_int |= MACE_MISC_INT;
+	if (!(maceisa_mask & MACEISA_SUPERIO_INT))
+		crime_int |= MACE_SUPERIO_INT;
+	crime_mask &= ~crime_int;
+	crime->imask = crime_mask;
+	flush_crime_bus();
+	mace->perif.ctrl.imask = maceisa_mask;
+	flush_mace_bus();
+}
+
+static void mask_and_ack_maceisa_irq(struct irq_data *d)
+{
+	unsigned long mace_int;
+
+	/* edge triggered */
+	mace_int = mace->perif.ctrl.istat;
+	mace_int &= ~(1 << (d->irq - MACEISA_AUDIO_SW_IRQ));
+	mace->perif.ctrl.istat = mace_int;
+
+	disable_maceisa_irq(d);
+}
+
+static struct irq_chip ip32_maceisa_level_interrupt = {
+	.name		= "IP32 MACE ISA",
+	.irq_mask	= disable_maceisa_irq,
+	.irq_unmask	= enable_maceisa_irq,
+};
+
+static struct irq_chip ip32_maceisa_edge_interrupt = {
+	.name		= "IP32 MACE ISA",
+	.irq_ack	= mask_and_ack_maceisa_irq,
+	.irq_mask	= disable_maceisa_irq,
+	.irq_mask_ack	= mask_and_ack_maceisa_irq,
+	.irq_unmask	= enable_maceisa_irq,
+};
+
+/* This is used for regular non-ISA, non-PCI MACE interrupts.  That means
+ * bits 0-3 and 7 in the CRIME register.
+ */
+
+static void enable_mace_irq(struct irq_data *d)
+{
+	unsigned int bit = d->irq - CRIME_IRQ_BASE;
+
+	crime_mask |= (1 << bit);
+	crime->imask = crime_mask;
+}
+
+static void disable_mace_irq(struct irq_data *d)
+{
+	unsigned int bit = d->irq - CRIME_IRQ_BASE;
+
+	crime_mask &= ~(1 << bit);
+	crime->imask = crime_mask;
+	flush_crime_bus();
+}
+
+static struct irq_chip ip32_mace_interrupt = {
+	.name = "IP32 MACE",
+	.irq_mask = disable_mace_irq,
+	.irq_unmask = enable_mace_irq,
+};
+
+static void ip32_unknown_interrupt(void)
+{
+	printk("Unknown interrupt occurred!\n");
+	printk("cp0_status: %08x\n", read_c0_status());
+	printk("cp0_cause: %08x\n", read_c0_cause());
+	printk("CRIME intr mask: %016lx\n", crime->imask);
+	printk("CRIME intr status: %016lx\n", crime->istat);
+	printk("CRIME hardware intr register: %016lx\n", crime->hard_int);
+	printk("MACE ISA intr mask: %08lx\n", mace->perif.ctrl.imask);
+	printk("MACE ISA intr status: %08lx\n", mace->perif.ctrl.istat);
+	printk("MACE PCI control register: %08x\n", mace->pci.control);
+
+	printk("Register dump:\n");
+	show_regs(get_irq_regs());
+
+	printk("Please mail this report to linux-mips@vger.kernel.org\n");
+	printk("Spinning...");
+	while(1) ;
+}
+
+/* CRIME 1.1 appears to deliver all interrupts to this one pin. */
+/* change this to loop over all edge-triggered irqs, exception masked out ones */
+static void ip32_irq0(void)
+{
+	uint64_t crime_int;
+	int irq = 0;
+
+	/*
+	 * Sanity check interrupt numbering enum.
+	 * MACE got 32 interrupts and there are 32 MACE ISA interrupts daisy
+	 * chained.
+	 */
+	BUILD_BUG_ON(CRIME_VICE_IRQ - MACE_VID_IN1_IRQ != 31);
+	BUILD_BUG_ON(MACEISA_SERIAL2_RDMAOR_IRQ - MACEISA_AUDIO_SW_IRQ != 31);
+
+	crime_int = crime->istat & crime_mask;
+
+	/* crime sometime delivers spurious interrupts, ignore them */
+	if (unlikely(crime_int == 0))
+		return;
+
+	irq = MACE_VID_IN1_IRQ + __ffs(crime_int);
+
+	if (crime_int & CRIME_MACEISA_INT_MASK) {
+		unsigned long mace_int = mace->perif.ctrl.istat;
+		irq = __ffs(mace_int & maceisa_mask) + MACEISA_AUDIO_SW_IRQ;
+	}
+
+	pr_debug("*irq %u*\n", irq);
+	do_IRQ(irq);
+}
+
+static void ip32_irq1(void)
+{
+	ip32_unknown_interrupt();
+}
+
+static void ip32_irq2(void)
+{
+	ip32_unknown_interrupt();
+}
+
+static void ip32_irq3(void)
+{
+	ip32_unknown_interrupt();
+}
+
+static void ip32_irq4(void)
+{
+	ip32_unknown_interrupt();
+}
+
+static void ip32_irq5(void)
+{
+	do_IRQ(MIPS_CPU_IRQ_BASE + 7);
+}
+
+asmlinkage void plat_irq_dispatch(void)
+{
+	unsigned int pending = read_c0_status() & read_c0_cause();
+
+	if (likely(pending & IE_IRQ0))
+		ip32_irq0();
+	else if (unlikely(pending & IE_IRQ1))
+		ip32_irq1();
+	else if (unlikely(pending & IE_IRQ2))
+		ip32_irq2();
+	else if (unlikely(pending & IE_IRQ3))
+		ip32_irq3();
+	else if (unlikely(pending & IE_IRQ4))
+		ip32_irq4();
+	else if (likely(pending & IE_IRQ5))
+		ip32_irq5();
+}
+
+void __init arch_init_irq(void)
+{
+	unsigned int irq;
+
+	/* Install our interrupt handler, then clear and disable all
+	 * CRIME and MACE interrupts. */
+	crime->imask = 0;
+	crime->hard_int = 0;
+	crime->soft_int = 0;
+	mace->perif.ctrl.istat = 0;
+	mace->perif.ctrl.imask = 0;
+
+	mips_cpu_irq_init();
+	for (irq = CRIME_IRQ_BASE; irq <= IP32_IRQ_MAX; irq++) {
+		switch (irq) {
+		case MACE_VID_IN1_IRQ ... MACE_PCI_BRIDGE_IRQ:
+			irq_set_chip_and_handler_name(irq,
+						      &ip32_mace_interrupt,
+						      handle_level_irq,
+						      "level");
+			break;
+
+		case MACEPCI_SCSI0_IRQ ...  MACEPCI_SHARED2_IRQ:
+			irq_set_chip_and_handler_name(irq,
+						      &ip32_macepci_interrupt,
+						      handle_level_irq,
+						      "level");
+			break;
+
+		case CRIME_CPUERR_IRQ:
+		case CRIME_MEMERR_IRQ:
+			irq_set_chip_and_handler_name(irq,
+						      &crime_level_interrupt,
+						      handle_level_irq,
+						      "level");
+			break;
+
+		case CRIME_GBE0_IRQ ... CRIME_GBE3_IRQ:
+		case CRIME_RE_EMPTY_E_IRQ ... CRIME_RE_IDLE_E_IRQ:
+		case CRIME_SOFT0_IRQ ... CRIME_SOFT2_IRQ:
+		case CRIME_VICE_IRQ:
+			irq_set_chip_and_handler_name(irq,
+						      &crime_edge_interrupt,
+						      handle_edge_irq,
+						      "edge");
+			break;
+
+		case MACEISA_PARALLEL_IRQ:
+		case MACEISA_SERIAL1_TDMAPR_IRQ:
+		case MACEISA_SERIAL2_TDMAPR_IRQ:
+			irq_set_chip_and_handler_name(irq,
+						      &ip32_maceisa_edge_interrupt,
+						      handle_edge_irq,
+						      "edge");
+			break;
+
+		default:
+			irq_set_chip_and_handler_name(irq,
+						      &ip32_maceisa_level_interrupt,
+						      handle_level_irq,
+						      "level");
+			break;
+		}
+	}
+	if (request_irq(CRIME_MEMERR_IRQ, crime_memerr_intr, 0,
+			"CRIME memory error", NULL))
+		pr_err("Failed to register CRIME memory error interrupt\n");
+	if (request_irq(CRIME_CPUERR_IRQ, crime_cpuerr_intr, 0,
+			"CRIME CPU error", NULL))
+		pr_err("Failed to register CRIME CPU error interrupt\n");
+
+#define ALLINTS (IE_IRQ0 | IE_IRQ1 | IE_IRQ2 | IE_IRQ3 | IE_IRQ4 | IE_IRQ5)
+	change_c0_status(ST0_IM, ALLINTS);
+}
diff --git a/arch/mips/sgi-ip32/ip32-memory.c b/arch/mips/sgi-ip32/ip32-memory.c
new file mode 100644
index 000000000..3fc8d0a0b
--- /dev/null
+++ b/arch/mips/sgi-ip32/ip32-memory.c
@@ -0,0 +1,42 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2003 Keith M Wesolowski
+ * Copyright (C) 2005 Ilya A. Volynets (Total Knowledge)
+ */
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/memblock.h>
+#include <linux/mm.h>
+
+#include <asm/ip32/crime.h>
+#include <asm/bootinfo.h>
+#include <asm/page.h>
+
+extern void crime_init(void);
+
+void __init prom_meminit(void)
+{
+	u64 base, size;
+	int bank;
+
+	crime_init();
+
+	for (bank=0; bank < CRIME_MAXBANKS; bank++) {
+		u64 bankctl = crime->bank_ctrl[bank];
+		base = (bankctl & CRIME_MEM_BANK_CONTROL_ADDR) << 25;
+		if (bank != 0 && base == 0)
+			continue;
+		size = (bankctl & CRIME_MEM_BANK_CONTROL_SDRAM_SIZE) ? 128 : 32;
+		size <<= 20;
+		if (base + size > (256 << 20))
+			base += CRIME_HI_MEM_BASE;
+
+		printk("CRIME MC: bank %u base 0x%016Lx size %LuMiB\n",
+			bank, base, size >> 20);
+		memblock_add(base, size);
+	}
+}
diff --git a/arch/mips/sgi-ip32/ip32-platform.c b/arch/mips/sgi-ip32/ip32-platform.c
new file mode 100644
index 000000000..c3909bd8d
--- /dev/null
+++ b/arch/mips/sgi-ip32/ip32-platform.c
@@ -0,0 +1,138 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2007 Ralf Baechle (ralf@linux-mips.org)
+ */
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/serial_8250.h>
+#include <linux/rtc/ds1685.h>
+
+#include <asm/ip32/mace.h>
+#include <asm/ip32/ip32_ints.h>
+
+extern void ip32_prepare_poweroff(void);
+
+#define MACEISA_SERIAL1_OFFS   offsetof(struct sgi_mace, isa.serial1)
+#define MACEISA_SERIAL2_OFFS   offsetof(struct sgi_mace, isa.serial2)
+
+#define MACE_PORT(offset,_irq)						\
+{									\
+	.mapbase	= MACE_BASE + offset,				\
+	.irq		= _irq,						\
+	.uartclk	= 1843200,					\
+	.iotype		= UPIO_MEM,					\
+	.flags		= UPF_SKIP_TEST|UPF_IOREMAP,			\
+	.regshift	= 8,						\
+}
+
+static struct plat_serial8250_port uart8250_data[] = {
+	MACE_PORT(MACEISA_SERIAL1_OFFS, MACEISA_SERIAL1_IRQ),
+	MACE_PORT(MACEISA_SERIAL2_OFFS, MACEISA_SERIAL2_IRQ),
+	{ },
+};
+
+static struct platform_device uart8250_device = {
+	.name			= "serial8250",
+	.id			= PLAT8250_DEV_PLATFORM,
+	.dev			= {
+		.platform_data	= uart8250_data,
+	},
+};
+
+static int __init uart8250_init(void)
+{
+	return platform_device_register(&uart8250_device);
+}
+
+device_initcall(uart8250_init);
+
+static __init int meth_devinit(void)
+{
+	struct platform_device *pd;
+	int ret;
+
+	pd = platform_device_alloc("meth", -1);
+	if (!pd)
+		return -ENOMEM;
+
+	ret = platform_device_add(pd);
+	if (ret)
+		platform_device_put(pd);
+
+	return ret;
+}
+
+device_initcall(meth_devinit);
+
+static __init int sgio2audio_devinit(void)
+{
+	struct platform_device *pd;
+	int ret;
+
+	pd = platform_device_alloc("sgio2audio", -1);
+	if (!pd)
+		return -ENOMEM;
+
+	ret = platform_device_add(pd);
+	if (ret)
+		platform_device_put(pd);
+
+	return ret;
+}
+
+device_initcall(sgio2audio_devinit);
+
+static __init int sgio2btns_devinit(void)
+{
+	return IS_ERR(platform_device_register_simple("sgibtns", -1, NULL, 0));
+}
+
+device_initcall(sgio2btns_devinit);
+
+#define MACE_RTC_RES_START (MACE_BASE + offsetof(struct sgi_mace, isa.rtc))
+#define MACE_RTC_RES_END (MACE_RTC_RES_START + 32767)
+
+static struct resource ip32_rtc_resources[] = {
+	{
+		.start	= MACEISA_RTC_IRQ,
+		.end	= MACEISA_RTC_IRQ,
+		.flags	= IORESOURCE_IRQ
+	}, {
+		.start	= MACE_RTC_RES_START,
+		.end	= MACE_RTC_RES_END,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
+/* RTC registers on IP32 are each padded by 256 bytes (0x100). */
+static struct ds1685_rtc_platform_data
+ip32_rtc_platform_data[] = {
+	{
+		.regstep = 0x100,
+		.bcd_mode = true,
+		.no_irq = false,
+		.uie_unsupported = false,
+		.access_type = ds1685_reg_direct,
+		.plat_prepare_poweroff = ip32_prepare_poweroff,
+	},
+};
+
+struct platform_device ip32_rtc_device = {
+	.name			= "rtc-ds1685",
+	.id			= -1,
+	.dev			= {
+		.platform_data	= ip32_rtc_platform_data,
+	},
+	.num_resources		= ARRAY_SIZE(ip32_rtc_resources),
+	.resource		= ip32_rtc_resources,
+};
+
+static __init int sgio2_rtc_devinit(void)
+{
+	return platform_device_register(&ip32_rtc_device);
+}
+
+device_initcall(sgio2_rtc_devinit);
diff --git a/arch/mips/sgi-ip32/ip32-reset.c b/arch/mips/sgi-ip32/ip32-reset.c
new file mode 100644
index 000000000..18d1c115c
--- /dev/null
+++ b/arch/mips/sgi-ip32/ip32-reset.c
@@ -0,0 +1,153 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2001 Keith M Wesolowski
+ * Copyright (C) 2001 Paul Mundt
+ * Copyright (C) 2003 Guido Guenther <agx@sigxcpu.org>
+ */
+
+#include <linux/compiler.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/panic_notifier.h>
+#include <linux/sched.h>
+#include <linux/sched/signal.h>
+#include <linux/notifier.h>
+#include <linux/delay.h>
+#include <linux/rtc/ds1685.h>
+#include <linux/interrupt.h>
+#include <linux/pm.h>
+
+#include <asm/addrspace.h>
+#include <asm/irq.h>
+#include <asm/reboot.h>
+#include <asm/wbflush.h>
+#include <asm/ip32/mace.h>
+#include <asm/ip32/crime.h>
+#include <asm/ip32/ip32_ints.h>
+
+#define POWERDOWN_TIMEOUT	120
+/*
+ * Blink frequency during reboot grace period and when panicked.
+ */
+#define POWERDOWN_FREQ		(HZ / 4)
+#define PANIC_FREQ		(HZ / 8)
+
+extern struct platform_device ip32_rtc_device;
+
+static struct timer_list power_timer, blink_timer;
+static unsigned long blink_timer_timeout;
+static int has_panicked, shutting_down;
+
+static __noreturn void ip32_poweroff(void *data)
+{
+	void (*poweroff_func)(struct platform_device *) =
+		symbol_get(ds1685_rtc_poweroff);
+
+#ifdef CONFIG_MODULES
+	/* If the first __symbol_get failed, our module wasn't loaded. */
+	if (!poweroff_func) {
+		request_module("rtc-ds1685");
+		poweroff_func = symbol_get(ds1685_rtc_poweroff);
+	}
+#endif
+
+	if (!poweroff_func)
+		pr_emerg("RTC not available for power-off.  Spinning forever ...\n");
+	else {
+		(*poweroff_func)((struct platform_device *)data);
+		symbol_put(ds1685_rtc_poweroff);
+	}
+
+	unreachable();
+}
+
+static void ip32_machine_restart(char *cmd) __noreturn;
+static void ip32_machine_restart(char *cmd)
+{
+	msleep(20);
+	crime->control = CRIME_CONTROL_HARD_RESET;
+	unreachable();
+}
+
+static void blink_timeout(struct timer_list *unused)
+{
+	unsigned long led = mace->perif.ctrl.misc ^ MACEISA_LED_RED;
+	mace->perif.ctrl.misc = led;
+	mod_timer(&blink_timer, jiffies + blink_timer_timeout);
+}
+
+static void ip32_machine_halt(void)
+{
+	ip32_poweroff(&ip32_rtc_device);
+}
+
+static void power_timeout(struct timer_list *unused)
+{
+	ip32_poweroff(&ip32_rtc_device);
+}
+
+void ip32_prepare_poweroff(void)
+{
+	if (has_panicked)
+		return;
+
+	if (shutting_down || kill_cad_pid(SIGINT, 1)) {
+		/* No init process or button pressed twice.  */
+		ip32_poweroff(&ip32_rtc_device);
+	}
+
+	shutting_down = 1;
+	blink_timer_timeout = POWERDOWN_FREQ;
+	blink_timeout(&blink_timer);
+
+	timer_setup(&power_timer, power_timeout, 0);
+	power_timer.expires = jiffies + POWERDOWN_TIMEOUT * HZ;
+	add_timer(&power_timer);
+}
+
+static int panic_event(struct notifier_block *this, unsigned long event,
+		       void *ptr)
+{
+	unsigned long led;
+
+	if (has_panicked)
+		return NOTIFY_DONE;
+	has_panicked = 1;
+
+	/* turn off the green LED */
+	led = mace->perif.ctrl.misc | MACEISA_LED_GREEN;
+	mace->perif.ctrl.misc = led;
+
+	blink_timer_timeout = PANIC_FREQ;
+	blink_timeout(&blink_timer);
+
+	return NOTIFY_DONE;
+}
+
+static struct notifier_block panic_block = {
+	.notifier_call = panic_event,
+};
+
+static __init int ip32_reboot_setup(void)
+{
+	/* turn on the green led only */
+	unsigned long led = mace->perif.ctrl.misc;
+	led |= MACEISA_LED_RED;
+	led &= ~MACEISA_LED_GREEN;
+	mace->perif.ctrl.misc = led;
+
+	_machine_restart = ip32_machine_restart;
+	_machine_halt = ip32_machine_halt;
+	pm_power_off = ip32_machine_halt;
+
+	timer_setup(&blink_timer, blink_timeout, 0);
+	atomic_notifier_chain_register(&panic_notifier_list, &panic_block);
+
+	return 0;
+}
+
+subsys_initcall(ip32_reboot_setup);
diff --git a/arch/mips/sgi-ip32/ip32-setup.c b/arch/mips/sgi-ip32/ip32-setup.c
new file mode 100644
index 000000000..8019dae17
--- /dev/null
+++ b/arch/mips/sgi-ip32/ip32-setup.c
@@ -0,0 +1,100 @@
+/*
+ * IP32 basic setup
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2000 Harald Koerfgen
+ * Copyright (C) 2002, 2003, 2005 Ilya A. Volynets
+ * Copyright (C) 2006 Ralf Baechle <ralf@linux-mips.org>
+ */
+#include <linux/console.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/param.h>
+#include <linux/sched.h>
+
+#include <asm/bootinfo.h>
+#include <asm/mipsregs.h>
+#include <asm/mmu_context.h>
+#include <asm/sgialib.h>
+#include <asm/time.h>
+#include <asm/traps.h>
+#include <asm/io.h>
+#include <asm/ip32/crime.h>
+#include <asm/ip32/mace.h>
+#include <asm/ip32/ip32_ints.h>
+
+extern void ip32_be_init(void);
+extern void crime_init(void);
+
+#ifdef CONFIG_SGI_O2MACE_ETH
+/*
+ * This is taken care of in here 'cause they say using Arc later on is
+ * problematic
+ */
+extern char o2meth_eaddr[8];
+static inline unsigned char str2hexnum(unsigned char c)
+{
+	if (c >= '0' && c <= '9')
+		return c - '0';
+	if (c >= 'a' && c <= 'f')
+		return c - 'a' + 10;
+	return 0; /* foo */
+}
+
+static inline void str2eaddr(unsigned char *ea, unsigned char *str)
+{
+	int i;
+
+	for (i = 0; i < 6; i++) {
+		unsigned char num;
+
+		if(*str == ':')
+			str++;
+		num = str2hexnum(*str++) << 4;
+		num |= (str2hexnum(*str++));
+		ea[i] = num;
+	}
+}
+#endif
+
+/* An arbitrary time; this can be decreased if reliability looks good */
+#define WAIT_MS 10
+
+void __init plat_time_init(void)
+{
+	printk(KERN_INFO "Calibrating system timer... ");
+	write_c0_count(0);
+	crime->timer = 0;
+	while (crime->timer < CRIME_MASTER_FREQ * WAIT_MS / 1000) ;
+	mips_hpt_frequency = read_c0_count() * 1000 / WAIT_MS;
+	printk("%d MHz CPU detected\n", mips_hpt_frequency * 2 / 1000000);
+}
+
+void __init plat_mem_setup(void)
+{
+	board_be_init = ip32_be_init;
+
+#ifdef CONFIG_SGI_O2MACE_ETH
+	{
+		char *mac = ArcGetEnvironmentVariable("eaddr");
+		str2eaddr(o2meth_eaddr, mac);
+	}
+#endif
+
+#if defined(CONFIG_SERIAL_CORE_CONSOLE)
+	{
+		char* con = ArcGetEnvironmentVariable("console");
+		if (con && *con == 'd') {
+			static char options[8] __initdata;
+			char *baud = ArcGetEnvironmentVariable("dbaud");
+			if (baud)
+				strcpy(options, baud);
+			add_preferred_console("ttyS", *(con + 1) == '2' ? 1 : 0,
+					      baud ? options : NULL);
+		}
+	}
+#endif
+}
diff --git a/arch/mips/sibyte/Kconfig b/arch/mips/sibyte/Kconfig
new file mode 100644
index 000000000..470d46183
--- /dev/null
+++ b/arch/mips/sibyte/Kconfig
@@ -0,0 +1,167 @@
+# SPDX-License-Identifier: GPL-2.0
+config SIBYTE_SB1250
+	bool
+	select CEVT_SB1250
+	select CSRC_SB1250
+	select HAVE_PCI
+	select IRQ_MIPS_CPU
+	select SIBYTE_ENABLE_LDT_IF_PCI
+	select SIBYTE_HAS_ZBUS_PROFILING
+	select SIBYTE_SB1xxx_SOC
+	select SYS_SUPPORTS_SMP
+
+config SIBYTE_BCM1120
+	bool
+	select CEVT_SB1250
+	select CSRC_SB1250
+	select IRQ_MIPS_CPU
+	select SIBYTE_BCM112X
+	select SIBYTE_HAS_ZBUS_PROFILING
+	select SIBYTE_SB1xxx_SOC
+
+config SIBYTE_BCM1125
+	bool
+	select CEVT_SB1250
+	select CSRC_SB1250
+	select HAVE_PCI
+	select IRQ_MIPS_CPU
+	select SIBYTE_BCM112X
+	select SIBYTE_HAS_ZBUS_PROFILING
+	select SIBYTE_SB1xxx_SOC
+
+config SIBYTE_BCM1125H
+	bool
+	select CEVT_SB1250
+	select CSRC_SB1250
+	select HAVE_PCI
+	select IRQ_MIPS_CPU
+	select SIBYTE_BCM112X
+	select SIBYTE_ENABLE_LDT_IF_PCI
+	select SIBYTE_HAS_ZBUS_PROFILING
+	select SIBYTE_SB1xxx_SOC
+
+config SIBYTE_BCM112X
+	bool
+	select CEVT_SB1250
+	select CSRC_SB1250
+	select IRQ_MIPS_CPU
+	select SIBYTE_SB1xxx_SOC
+	select SIBYTE_HAS_ZBUS_PROFILING
+
+config SIBYTE_BCM1x80
+	bool
+	select CEVT_BCM1480
+	select CSRC_BCM1480
+	select HAVE_PCI
+	select IRQ_MIPS_CPU
+	select SIBYTE_HAS_ZBUS_PROFILING
+	select SIBYTE_SB1xxx_SOC
+	select SYS_SUPPORTS_SMP
+
+config SIBYTE_BCM1x55
+	bool
+	select CEVT_BCM1480
+	select CSRC_BCM1480
+	select HAVE_PCI
+	select IRQ_MIPS_CPU
+	select SIBYTE_SB1xxx_SOC
+	select SIBYTE_HAS_ZBUS_PROFILING
+	select SYS_SUPPORTS_SMP
+
+config SIBYTE_SB1xxx_SOC
+	bool
+	select IRQ_MIPS_CPU
+	select SWAP_IO_SPACE
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_64BIT_KERNEL
+	select FW_CFE
+	select SYS_HAS_EARLY_PRINTK
+
+choice
+	prompt "SiByte SOC Stepping"
+	depends on SIBYTE_SB1xxx_SOC
+
+config CPU_SB1_PASS_2_1250
+	bool "1250 An"
+	depends on SIBYTE_SB1250
+	select CPU_SB1_PASS_2
+	help
+	  Also called BCM1250 Pass 2
+
+config CPU_SB1_PASS_2_2
+	bool "1250 Bn"
+	depends on SIBYTE_SB1250
+	select CPU_HAS_PREFETCH
+	help
+	  Also called BCM1250 Pass 2.2
+
+config CPU_SB1_PASS_4
+	bool "1250 Cn"
+	depends on SIBYTE_SB1250
+	select CPU_HAS_PREFETCH
+	help
+	  Also called BCM1250 Pass 3
+
+config CPU_SB1_PASS_2_112x
+	bool "112x Hybrid"
+	depends on SIBYTE_BCM112X
+	select CPU_SB1_PASS_2
+
+config CPU_SB1_PASS_3
+	bool "112x An"
+	depends on SIBYTE_BCM112X
+	select CPU_HAS_PREFETCH
+
+endchoice
+
+config CPU_SB1_PASS_2
+	bool
+
+config SIBYTE_HAS_LDT
+	bool
+
+config SIBYTE_ENABLE_LDT_IF_PCI
+	bool
+	select SIBYTE_HAS_LDT if PCI
+
+config SB1_CEX_ALWAYS_FATAL
+	bool "All cache exceptions considered fatal (no recovery attempted)"
+	depends on SIBYTE_SB1xxx_SOC
+
+config SB1_CERR_STALL
+	bool "Stall (rather than panic) on fatal cache error"
+	depends on SIBYTE_SB1xxx_SOC
+
+config SIBYTE_CFE_CONSOLE
+	bool "Use firmware console"
+	depends on SIBYTE_SB1xxx_SOC
+	help
+	  Use the CFE API's console write routines during boot.  Other console
+	  options (VT console, sb1250 duart console, etc.) should not be
+	  configured.
+
+config SIBYTE_BUS_WATCHER
+	bool "Support for Bus Watcher statistics"
+	depends on SIBYTE_SB1xxx_SOC && \
+		(SIBYTE_BCM112X || SIBYTE_SB1250 || \
+		 SIBYTE_BCM1x55 || SIBYTE_BCM1x80)
+	help
+	  Handle and keep statistics on the bus error interrupts (COR_ECC,
+	  BAD_ECC, IO_BUS).
+
+config SIBYTE_BW_TRACE
+	bool "Capture bus trace before bus error"
+	depends on SIBYTE_BUS_WATCHER
+	help
+	  Run a continuous bus trace, dumping the raw data as soon as
+	  a ZBbus error is detected.  Cannot work if ZBbus profiling
+	  is turned on, and also will interfere with JTAG-based trace
+	  buffer activity.  Raw buffer data is dumped to console, and
+	  must be processed off-line.
+
+config SIBYTE_TBPROF
+	tristate "Support for ZBbus profiling"
+	depends on SIBYTE_HAS_ZBUS_PROFILING
+
+config SIBYTE_HAS_ZBUS_PROFILING
+	bool
diff --git a/arch/mips/sibyte/Makefile b/arch/mips/sibyte/Makefile
new file mode 100644
index 000000000..d015c4d79
--- /dev/null
+++ b/arch/mips/sibyte/Makefile
@@ -0,0 +1,29 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Sibyte SB1250 / BCM1480 family of SOCs
+#
+obj-$(CONFIG_SIBYTE_BCM112X)	+= sb1250/
+obj-$(CONFIG_SIBYTE_BCM112X)	+= common/
+obj-$(CONFIG_SIBYTE_SB1250)	+= sb1250/
+obj-$(CONFIG_SIBYTE_SB1250)	+= common/
+obj-$(CONFIG_SIBYTE_BCM1x55)	+= bcm1480/
+obj-$(CONFIG_SIBYTE_BCM1x55)	+= common/
+obj-$(CONFIG_SIBYTE_BCM1x80)	+= bcm1480/
+obj-$(CONFIG_SIBYTE_BCM1x80)	+= common/
+
+#
+# Sibyte BCM91120x (Carmel) board
+# Sibyte BCM91120C (CRhine) board
+# Sibyte BCM91125C (CRhone) board
+# Sibyte BCM91125E (Rhone) board
+# Sibyte SWARM board
+# Sibyte BCM91x80 (BigSur) board
+#
+obj-$(CONFIG_SIBYTE_CARMEL)	+= swarm/
+obj-$(CONFIG_SIBYTE_CRHINE)	+= swarm/
+obj-$(CONFIG_SIBYTE_CRHONE)	+= swarm/
+obj-$(CONFIG_SIBYTE_RHONE)	+= swarm/
+obj-$(CONFIG_SIBYTE_SENTOSA)	+= swarm/
+obj-$(CONFIG_SIBYTE_SWARM)	+= swarm/
+obj-$(CONFIG_SIBYTE_BIGSUR)	+= swarm/
+obj-$(CONFIG_SIBYTE_LITTLESUR)	+= swarm/
diff --git a/arch/mips/sibyte/Platform b/arch/mips/sibyte/Platform
new file mode 100644
index 000000000..65b2225b7
--- /dev/null
+++ b/arch/mips/sibyte/Platform
@@ -0,0 +1,40 @@
+#
+# These are all rather similar so we consider them a single platform
+#
+
+#
+# Sibyte SB1250 / BCM1480 family of SOCs
+#
+cflags-$(CONFIG_SIBYTE_BCM112X) +=					\
+		-I$(srctree)/arch/mips/include/asm/mach-sibyte		\
+		-DSIBYTE_HDR_FEATURES=SIBYTE_HDR_FMASK_1250_112x_ALL
+
+cflags-$(CONFIG_SIBYTE_SB1250)	+=					\
+		-I$(srctree)/arch/mips/include/asm/mach-sibyte		\
+		-DSIBYTE_HDR_FEATURES=SIBYTE_HDR_FMASK_1250_112x_ALL
+
+cflags-$(CONFIG_SIBYTE_BCM1x55) +=					\
+		-I$(srctree)/arch/mips/include/asm/mach-sibyte		\
+		-DSIBYTE_HDR_FEATURES=SIBYTE_HDR_FMASK_1480_ALL
+
+cflags-$(CONFIG_SIBYTE_BCM1x80) +=					\
+		-I$(srctree)/arch/mips/include/asm/mach-sibyte		\
+		-DSIBYTE_HDR_FEATURES=SIBYTE_HDR_FMASK_1480_ALL
+
+#
+# Sibyte BCM91120x (Carmel) board
+# Sibyte BCM91120C (CRhine) board
+# Sibyte BCM91125C (CRhone) board
+# Sibyte BCM91125E (Rhone) board
+# Sibyte BCM91250A (SWARM) board
+# Sibyte BCM91250C2 (LittleSur) board
+# Sibyte BCM91x80 (BigSur) board
+#
+load-$(CONFIG_SIBYTE_CARMEL)	:= 0xffffffff80100000
+load-$(CONFIG_SIBYTE_CRHINE)	:= 0xffffffff80100000
+load-$(CONFIG_SIBYTE_CRHONE)	:= 0xffffffff80100000
+load-$(CONFIG_SIBYTE_RHONE)	:= 0xffffffff80100000
+load-$(CONFIG_SIBYTE_SENTOSA)	:= 0xffffffff80100000
+load-$(CONFIG_SIBYTE_SWARM)	:= 0xffffffff80100000
+load-$(CONFIG_SIBYTE_BIGSUR)	:= 0xffffffff80100000
+load-$(CONFIG_SIBYTE_LITTLESUR) := 0xffffffff80100000
diff --git a/arch/mips/sibyte/bcm1480/Makefile b/arch/mips/sibyte/bcm1480/Makefile
new file mode 100644
index 000000000..cf1327d3f
--- /dev/null
+++ b/arch/mips/sibyte/bcm1480/Makefile
@@ -0,0 +1,4 @@
+# SPDX-License-Identifier: GPL-2.0-only
+obj-y := setup.o irq.o time.o
+
+obj-$(CONFIG_SMP)			+= smp.o
diff --git a/arch/mips/sibyte/bcm1480/irq.c b/arch/mips/sibyte/bcm1480/irq.c
new file mode 100644
index 000000000..7929bee91
--- /dev/null
+++ b/arch/mips/sibyte/bcm1480/irq.c
@@ -0,0 +1,348 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2000,2001,2002,2003,2004 Broadcom Corporation
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/linkage.h>
+#include <linux/interrupt.h>
+#include <linux/smp.h>
+#include <linux/spinlock.h>
+#include <linux/mm.h>
+#include <linux/kernel_stat.h>
+
+#include <asm/errno.h>
+#include <asm/irq_regs.h>
+#include <asm/signal.h>
+#include <asm/io.h>
+
+#include <asm/sibyte/bcm1480_regs.h>
+#include <asm/sibyte/bcm1480_int.h>
+#include <asm/sibyte/bcm1480_scd.h>
+
+#include <asm/sibyte/sb1250_uart.h>
+#include <asm/sibyte/sb1250.h>
+
+/*
+ * These are the routines that handle all the low level interrupt stuff.
+ * Actions handled here are: initialization of the interrupt map, requesting of
+ * interrupt lines by handlers, dispatching if interrupts to handlers, probing
+ * for interrupt lines
+ */
+
+#ifdef CONFIG_PCI
+extern unsigned long ht_eoi_space;
+#endif
+
+/* Store the CPU id (not the logical number) */
+int bcm1480_irq_owner[BCM1480_NR_IRQS];
+
+static DEFINE_RAW_SPINLOCK(bcm1480_imr_lock);
+
+void bcm1480_mask_irq(int cpu, int irq)
+{
+	unsigned long flags, hl_spacing;
+	u64 cur_ints;
+
+	raw_spin_lock_irqsave(&bcm1480_imr_lock, flags);
+	hl_spacing = 0;
+	if ((irq >= BCM1480_NR_IRQS_HALF) && (irq <= BCM1480_NR_IRQS)) {
+		hl_spacing = BCM1480_IMR_HL_SPACING;
+		irq -= BCM1480_NR_IRQS_HALF;
+	}
+	cur_ints = ____raw_readq(IOADDR(A_BCM1480_IMR_MAPPER(cpu) + R_BCM1480_IMR_INTERRUPT_MASK_H + hl_spacing));
+	cur_ints |= (((u64) 1) << irq);
+	____raw_writeq(cur_ints, IOADDR(A_BCM1480_IMR_MAPPER(cpu) + R_BCM1480_IMR_INTERRUPT_MASK_H + hl_spacing));
+	raw_spin_unlock_irqrestore(&bcm1480_imr_lock, flags);
+}
+
+void bcm1480_unmask_irq(int cpu, int irq)
+{
+	unsigned long flags, hl_spacing;
+	u64 cur_ints;
+
+	raw_spin_lock_irqsave(&bcm1480_imr_lock, flags);
+	hl_spacing = 0;
+	if ((irq >= BCM1480_NR_IRQS_HALF) && (irq <= BCM1480_NR_IRQS)) {
+		hl_spacing = BCM1480_IMR_HL_SPACING;
+		irq -= BCM1480_NR_IRQS_HALF;
+	}
+	cur_ints = ____raw_readq(IOADDR(A_BCM1480_IMR_MAPPER(cpu) + R_BCM1480_IMR_INTERRUPT_MASK_H + hl_spacing));
+	cur_ints &= ~(((u64) 1) << irq);
+	____raw_writeq(cur_ints, IOADDR(A_BCM1480_IMR_MAPPER(cpu) + R_BCM1480_IMR_INTERRUPT_MASK_H + hl_spacing));
+	raw_spin_unlock_irqrestore(&bcm1480_imr_lock, flags);
+}
+
+#ifdef CONFIG_SMP
+static int bcm1480_set_affinity(struct irq_data *d, const struct cpumask *mask,
+				bool force)
+{
+	unsigned int irq_dirty, irq = d->irq;
+	int i = 0, old_cpu, cpu, int_on, k;
+	u64 cur_ints;
+	unsigned long flags;
+
+	i = cpumask_first_and(mask, cpu_online_mask);
+
+	/* Convert logical CPU to physical CPU */
+	cpu = cpu_logical_map(i);
+
+	/* Protect against other affinity changers and IMR manipulation */
+	raw_spin_lock_irqsave(&bcm1480_imr_lock, flags);
+
+	/* Swizzle each CPU's IMR (but leave the IP selection alone) */
+	old_cpu = bcm1480_irq_owner[irq];
+	irq_dirty = irq;
+	if ((irq_dirty >= BCM1480_NR_IRQS_HALF) && (irq_dirty <= BCM1480_NR_IRQS)) {
+		irq_dirty -= BCM1480_NR_IRQS_HALF;
+	}
+
+	for (k=0; k<2; k++) { /* Loop through high and low interrupt mask register */
+		cur_ints = ____raw_readq(IOADDR(A_BCM1480_IMR_MAPPER(old_cpu) + R_BCM1480_IMR_INTERRUPT_MASK_H + (k*BCM1480_IMR_HL_SPACING)));
+		int_on = !(cur_ints & (((u64) 1) << irq_dirty));
+		if (int_on) {
+			/* If it was on, mask it */
+			cur_ints |= (((u64) 1) << irq_dirty);
+			____raw_writeq(cur_ints, IOADDR(A_BCM1480_IMR_MAPPER(old_cpu) + R_BCM1480_IMR_INTERRUPT_MASK_H + (k*BCM1480_IMR_HL_SPACING)));
+		}
+		bcm1480_irq_owner[irq] = cpu;
+		if (int_on) {
+			/* unmask for the new CPU */
+			cur_ints = ____raw_readq(IOADDR(A_BCM1480_IMR_MAPPER(cpu) + R_BCM1480_IMR_INTERRUPT_MASK_H + (k*BCM1480_IMR_HL_SPACING)));
+			cur_ints &= ~(((u64) 1) << irq_dirty);
+			____raw_writeq(cur_ints, IOADDR(A_BCM1480_IMR_MAPPER(cpu) + R_BCM1480_IMR_INTERRUPT_MASK_H + (k*BCM1480_IMR_HL_SPACING)));
+		}
+	}
+	raw_spin_unlock_irqrestore(&bcm1480_imr_lock, flags);
+
+	return 0;
+}
+#endif
+
+
+/*****************************************************************************/
+
+static void disable_bcm1480_irq(struct irq_data *d)
+{
+	unsigned int irq = d->irq;
+
+	bcm1480_mask_irq(bcm1480_irq_owner[irq], irq);
+}
+
+static void enable_bcm1480_irq(struct irq_data *d)
+{
+	unsigned int irq = d->irq;
+
+	bcm1480_unmask_irq(bcm1480_irq_owner[irq], irq);
+}
+
+
+static void ack_bcm1480_irq(struct irq_data *d)
+{
+	unsigned int irq_dirty, irq = d->irq;
+	u64 pending;
+	int k;
+
+	/*
+	 * If the interrupt was an HT interrupt, now is the time to
+	 * clear it.  NOTE: we assume the HT bridge was set up to
+	 * deliver the interrupts to all CPUs (which makes affinity
+	 * changing easier for us)
+	 */
+	irq_dirty = irq;
+	if ((irq_dirty >= BCM1480_NR_IRQS_HALF) && (irq_dirty <= BCM1480_NR_IRQS)) {
+		irq_dirty -= BCM1480_NR_IRQS_HALF;
+	}
+	for (k=0; k<2; k++) { /* Loop through high and low LDT interrupts */
+		pending = __raw_readq(IOADDR(A_BCM1480_IMR_REGISTER(bcm1480_irq_owner[irq],
+						R_BCM1480_IMR_LDT_INTERRUPT_H + (k*BCM1480_IMR_HL_SPACING))));
+		pending &= ((u64)1 << (irq_dirty));
+		if (pending) {
+#ifdef CONFIG_SMP
+			int i;
+			for (i=0; i<NR_CPUS; i++) {
+				/*
+				 * Clear for all CPUs so an affinity switch
+				 * doesn't find an old status
+				 */
+				__raw_writeq(pending, IOADDR(A_BCM1480_IMR_REGISTER(cpu_logical_map(i),
+								R_BCM1480_IMR_LDT_INTERRUPT_CLR_H + (k*BCM1480_IMR_HL_SPACING))));
+			}
+#else
+			__raw_writeq(pending, IOADDR(A_BCM1480_IMR_REGISTER(0, R_BCM1480_IMR_LDT_INTERRUPT_CLR_H + (k*BCM1480_IMR_HL_SPACING))));
+#endif
+
+			/*
+			 * Generate EOI.  For Pass 1 parts, EOI is a nop.  For
+			 * Pass 2, the LDT world may be edge-triggered, but
+			 * this EOI shouldn't hurt.  If they are
+			 * level-sensitive, the EOI is required.
+			 */
+#ifdef CONFIG_PCI
+			if (ht_eoi_space)
+				*(uint32_t *)(ht_eoi_space+(irq<<16)+(7<<2)) = 0;
+#endif
+		}
+	}
+	bcm1480_mask_irq(bcm1480_irq_owner[irq], irq);
+}
+
+static struct irq_chip bcm1480_irq_type = {
+	.name = "BCM1480-IMR",
+	.irq_mask_ack = ack_bcm1480_irq,
+	.irq_mask = disable_bcm1480_irq,
+	.irq_unmask = enable_bcm1480_irq,
+#ifdef CONFIG_SMP
+	.irq_set_affinity = bcm1480_set_affinity
+#endif
+};
+
+void __init init_bcm1480_irqs(void)
+{
+	int i;
+
+	for (i = 0; i < BCM1480_NR_IRQS; i++) {
+		irq_set_chip_and_handler(i, &bcm1480_irq_type,
+					 handle_level_irq);
+		bcm1480_irq_owner[i] = 0;
+	}
+}
+
+/*
+ *  init_IRQ is called early in the boot sequence from init/main.c.  It
+ *  is responsible for setting up the interrupt mapper and installing the
+ *  handler that will be responsible for dispatching interrupts to the
+ *  "right" place.
+ */
+/*
+ * For now, map all interrupts to IP[2].  We could save
+ * some cycles by parceling out system interrupts to different
+ * IP lines, but keep it simple for bringup.  We'll also direct
+ * all interrupts to a single CPU; we should probably route
+ * PCI and LDT to one cpu and everything else to the other
+ * to balance the load a bit.
+ *
+ * On the second cpu, everything is set to IP5, which is
+ * ignored, EXCEPT the mailbox interrupt.  That one is
+ * set to IP[2] so it is handled.  This is needed so we
+ * can do cross-cpu function calls, as required by SMP
+ */
+
+#define IMR_IP2_VAL	K_BCM1480_INT_MAP_I0
+#define IMR_IP3_VAL	K_BCM1480_INT_MAP_I1
+#define IMR_IP4_VAL	K_BCM1480_INT_MAP_I2
+#define IMR_IP5_VAL	K_BCM1480_INT_MAP_I3
+#define IMR_IP6_VAL	K_BCM1480_INT_MAP_I4
+
+void __init arch_init_irq(void)
+{
+	unsigned int i, cpu;
+	u64 tmp;
+	unsigned int imask = STATUSF_IP4 | STATUSF_IP3 | STATUSF_IP2 |
+		STATUSF_IP1 | STATUSF_IP0;
+
+	/* Default everything to IP2 */
+	/* Start with _high registers which has no bit 0 interrupt source */
+	for (i = 1; i < BCM1480_NR_IRQS_HALF; i++) {	/* was I0 */
+		for (cpu = 0; cpu < 4; cpu++) {
+			__raw_writeq(IMR_IP2_VAL,
+				     IOADDR(A_BCM1480_IMR_REGISTER(cpu,
+								   R_BCM1480_IMR_INTERRUPT_MAP_BASE_H) + (i << 3)));
+		}
+	}
+
+	/* Now do _low registers */
+	for (i = 0; i < BCM1480_NR_IRQS_HALF; i++) {
+		for (cpu = 0; cpu < 4; cpu++) {
+			__raw_writeq(IMR_IP2_VAL,
+				     IOADDR(A_BCM1480_IMR_REGISTER(cpu,
+								   R_BCM1480_IMR_INTERRUPT_MAP_BASE_L) + (i << 3)));
+		}
+	}
+
+	init_bcm1480_irqs();
+
+	/*
+	 * Map the high 16 bits of mailbox_0 registers to IP[3], for
+	 * inter-cpu messages
+	 */
+	/* Was I1 */
+	for (cpu = 0; cpu < 4; cpu++) {
+		__raw_writeq(IMR_IP3_VAL, IOADDR(A_BCM1480_IMR_REGISTER(cpu, R_BCM1480_IMR_INTERRUPT_MAP_BASE_H) +
+						 (K_BCM1480_INT_MBOX_0_0 << 3)));
+	}
+
+
+	/* Clear the mailboxes.	 The firmware may leave them dirty */
+	for (cpu = 0; cpu < 4; cpu++) {
+		__raw_writeq(0xffffffffffffffffULL,
+			     IOADDR(A_BCM1480_IMR_REGISTER(cpu, R_BCM1480_IMR_MAILBOX_0_CLR_CPU)));
+		__raw_writeq(0xffffffffffffffffULL,
+			     IOADDR(A_BCM1480_IMR_REGISTER(cpu, R_BCM1480_IMR_MAILBOX_1_CLR_CPU)));
+	}
+
+
+	/* Mask everything except the high 16 bit of mailbox_0 registers for all cpus */
+	tmp = ~((u64) 0) ^ ( (((u64) 1) << K_BCM1480_INT_MBOX_0_0));
+	for (cpu = 0; cpu < 4; cpu++) {
+		__raw_writeq(tmp, IOADDR(A_BCM1480_IMR_REGISTER(cpu, R_BCM1480_IMR_INTERRUPT_MASK_H)));
+	}
+	tmp = ~((u64) 0);
+	for (cpu = 0; cpu < 4; cpu++) {
+		__raw_writeq(tmp, IOADDR(A_BCM1480_IMR_REGISTER(cpu, R_BCM1480_IMR_INTERRUPT_MASK_L)));
+	}
+
+	/*
+	 * Note that the timer interrupts are also mapped, but this is
+	 * done in bcm1480_time_init().	 Also, the profiling driver
+	 * does its own management of IP7.
+	 */
+
+	/* Enable necessary IPs, disable the rest */
+	change_c0_status(ST0_IM, imask);
+}
+
+extern void bcm1480_mailbox_interrupt(void);
+
+static inline void dispatch_ip2(void)
+{
+	unsigned long long mask_h, mask_l;
+	unsigned int cpu = smp_processor_id();
+	unsigned long base;
+
+	/*
+	 * Default...we've hit an IP[2] interrupt, which means we've got to
+	 * check the 1480 interrupt registers to figure out what to do.	 Need
+	 * to detect which CPU we're on, now that smp_affinity is supported.
+	 */
+	base = A_BCM1480_IMR_MAPPER(cpu);
+	mask_h = __raw_readq(
+		IOADDR(base + R_BCM1480_IMR_INTERRUPT_STATUS_BASE_H));
+	mask_l = __raw_readq(
+		IOADDR(base + R_BCM1480_IMR_INTERRUPT_STATUS_BASE_L));
+
+	if (mask_h) {
+		if (mask_h ^ 1)
+			do_IRQ(fls64(mask_h) - 1);
+		else if (mask_l)
+			do_IRQ(63 + fls64(mask_l));
+	}
+}
+
+asmlinkage void plat_irq_dispatch(void)
+{
+	unsigned int cpu = smp_processor_id();
+	unsigned int pending;
+
+	pending = read_c0_cause() & read_c0_status();
+
+	if (pending & CAUSEF_IP4)
+		do_IRQ(K_BCM1480_INT_TIMER_0 + cpu);
+#ifdef CONFIG_SMP
+	else if (pending & CAUSEF_IP3)
+		bcm1480_mailbox_interrupt();
+#endif
+
+	else if (pending & CAUSEF_IP2)
+		dispatch_ip2();
+}
diff --git a/arch/mips/sibyte/bcm1480/setup.c b/arch/mips/sibyte/bcm1480/setup.c
new file mode 100644
index 000000000..e3e807046
--- /dev/null
+++ b/arch/mips/sibyte/bcm1480/setup.c
@@ -0,0 +1,126 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2000,2001,2002,2003,2004 Broadcom Corporation
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/export.h>
+#include <linux/reboot.h>
+#include <linux/string.h>
+
+#include <asm/bootinfo.h>
+#include <asm/cpu.h>
+#include <asm/mipsregs.h>
+#include <asm/io.h>
+#include <asm/sibyte/sb1250.h>
+
+#include <asm/sibyte/bcm1480_regs.h>
+#include <asm/sibyte/bcm1480_scd.h>
+#include <asm/sibyte/sb1250_scd.h>
+
+unsigned int sb1_pass;
+unsigned int soc_pass;
+unsigned int soc_type;
+EXPORT_SYMBOL(soc_type);
+unsigned int periph_rev;
+EXPORT_SYMBOL_GPL(periph_rev);
+unsigned int zbbus_mhz;
+EXPORT_SYMBOL(zbbus_mhz);
+
+static unsigned int part_type;
+
+static char *soc_str;
+static char *pass_str;
+
+static int __init setup_bcm1x80_bcm1x55(void)
+{
+	switch (soc_pass) {
+	case K_SYS_REVISION_BCM1480_S0:
+		periph_rev = 1;
+		pass_str = "S0 (pass1)";
+		break;
+	case K_SYS_REVISION_BCM1480_A1:
+		periph_rev = 1;
+		pass_str = "A1 (pass1)";
+		break;
+	case K_SYS_REVISION_BCM1480_A2:
+		periph_rev = 1;
+		pass_str = "A2 (pass1)";
+		break;
+	case K_SYS_REVISION_BCM1480_A3:
+		periph_rev = 1;
+		pass_str = "A3 (pass1)";
+		break;
+	case K_SYS_REVISION_BCM1480_B0:
+		periph_rev = 1;
+		pass_str = "B0 (pass2)";
+		break;
+	default:
+		printk("Unknown %s rev %x\n", soc_str, soc_pass);
+		periph_rev = 1;
+		pass_str = "Unknown Revision";
+		break;
+	}
+
+	return 0;
+}
+
+/* Setup code likely to be common to all SiByte platforms */
+
+static int __init sys_rev_decode(void)
+{
+	int ret = 0;
+
+	switch (soc_type) {
+	case K_SYS_SOC_TYPE_BCM1x80:
+		if (part_type == K_SYS_PART_BCM1480)
+		    soc_str = "BCM1480";
+		else if (part_type == K_SYS_PART_BCM1280)
+		    soc_str = "BCM1280";
+		else
+		    soc_str = "BCM1x80";
+		ret = setup_bcm1x80_bcm1x55();
+		break;
+
+	case K_SYS_SOC_TYPE_BCM1x55:
+		if (part_type == K_SYS_PART_BCM1455)
+		    soc_str = "BCM1455";
+		else if (part_type == K_SYS_PART_BCM1255)
+		    soc_str = "BCM1255";
+		else
+		    soc_str = "BCM1x55";
+		ret = setup_bcm1x80_bcm1x55();
+		break;
+
+	default:
+		printk("Unknown part type %x\n", part_type);
+		ret = 1;
+		break;
+	}
+
+	return ret;
+}
+
+void __init bcm1480_setup(void)
+{
+	uint64_t sys_rev;
+	int plldiv;
+
+	sb1_pass = read_c0_prid() & PRID_REV_MASK;
+	sys_rev = __raw_readq(IOADDR(A_SCD_SYSTEM_REVISION));
+	soc_type = SYS_SOC_TYPE(sys_rev);
+	part_type = G_SYS_PART(sys_rev);
+	soc_pass = G_SYS_REVISION(sys_rev);
+
+	if (sys_rev_decode()) {
+		printk("Restart after failure to identify SiByte chip\n");
+		machine_restart(NULL);
+	}
+
+	plldiv = G_BCM1480_SYS_PLL_DIV(__raw_readq(IOADDR(A_SCD_SYSTEM_CFG)));
+	zbbus_mhz = ((plldiv >> 1) * 50) + ((plldiv & 1) * 25);
+
+	printk("Broadcom SiByte %s %s @ %d MHz (SB-1A rev %d)\n",
+		    soc_str, pass_str, zbbus_mhz * 2, sb1_pass);
+	printk("Board type: %s\n", get_system_type());
+}
diff --git a/arch/mips/sibyte/bcm1480/smp.c b/arch/mips/sibyte/bcm1480/smp.c
new file mode 100644
index 000000000..5861e5025
--- /dev/null
+++ b/arch/mips/sibyte/bcm1480/smp.c
@@ -0,0 +1,179 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2001,2002,2004 Broadcom Corporation
+ */
+
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/smp.h>
+#include <linux/kernel_stat.h>
+#include <linux/sched.h>
+#include <linux/sched/task_stack.h>
+
+#include <asm/mmu_context.h>
+#include <asm/io.h>
+#include <asm/fw/cfe/cfe_api.h>
+#include <asm/sibyte/sb1250.h>
+#include <asm/sibyte/bcm1480_regs.h>
+#include <asm/sibyte/bcm1480_int.h>
+
+/*
+ * These are routines for dealing with the bcm1480 smp capabilities
+ * independent of board/firmware
+ */
+
+static void *mailbox_0_set_regs[] = {
+	IOADDR(A_BCM1480_IMR_CPU0_BASE + R_BCM1480_IMR_MAILBOX_0_SET_CPU),
+	IOADDR(A_BCM1480_IMR_CPU1_BASE + R_BCM1480_IMR_MAILBOX_0_SET_CPU),
+	IOADDR(A_BCM1480_IMR_CPU2_BASE + R_BCM1480_IMR_MAILBOX_0_SET_CPU),
+	IOADDR(A_BCM1480_IMR_CPU3_BASE + R_BCM1480_IMR_MAILBOX_0_SET_CPU),
+};
+
+static void *mailbox_0_clear_regs[] = {
+	IOADDR(A_BCM1480_IMR_CPU0_BASE + R_BCM1480_IMR_MAILBOX_0_CLR_CPU),
+	IOADDR(A_BCM1480_IMR_CPU1_BASE + R_BCM1480_IMR_MAILBOX_0_CLR_CPU),
+	IOADDR(A_BCM1480_IMR_CPU2_BASE + R_BCM1480_IMR_MAILBOX_0_CLR_CPU),
+	IOADDR(A_BCM1480_IMR_CPU3_BASE + R_BCM1480_IMR_MAILBOX_0_CLR_CPU),
+};
+
+static void *mailbox_0_regs[] = {
+	IOADDR(A_BCM1480_IMR_CPU0_BASE + R_BCM1480_IMR_MAILBOX_0_CPU),
+	IOADDR(A_BCM1480_IMR_CPU1_BASE + R_BCM1480_IMR_MAILBOX_0_CPU),
+	IOADDR(A_BCM1480_IMR_CPU2_BASE + R_BCM1480_IMR_MAILBOX_0_CPU),
+	IOADDR(A_BCM1480_IMR_CPU3_BASE + R_BCM1480_IMR_MAILBOX_0_CPU),
+};
+
+/*
+ * SMP init and finish on secondary CPUs
+ */
+void bcm1480_smp_init(void)
+{
+	unsigned int imask = STATUSF_IP4 | STATUSF_IP3 | STATUSF_IP2 |
+		STATUSF_IP1 | STATUSF_IP0;
+
+	/* Set interrupt mask, but don't enable */
+	change_c0_status(ST0_IM, imask);
+}
+
+/*
+ * These are routines for dealing with the sb1250 smp capabilities
+ * independent of board/firmware
+ */
+
+/*
+ * Simple enough; everything is set up, so just poke the appropriate mailbox
+ * register, and we should be set
+ */
+static void bcm1480_send_ipi_single(int cpu, unsigned int action)
+{
+	__raw_writeq((((u64)action)<< 48), mailbox_0_set_regs[cpu]);
+}
+
+static void bcm1480_send_ipi_mask(const struct cpumask *mask,
+				  unsigned int action)
+{
+	unsigned int i;
+
+	for_each_cpu(i, mask)
+		bcm1480_send_ipi_single(i, action);
+}
+
+/*
+ * Code to run on secondary just after probing the CPU
+ */
+static void bcm1480_init_secondary(void)
+{
+	extern void bcm1480_smp_init(void);
+
+	bcm1480_smp_init();
+}
+
+/*
+ * Do any tidying up before marking online and running the idle
+ * loop
+ */
+static void bcm1480_smp_finish(void)
+{
+	extern void sb1480_clockevent_init(void);
+
+	sb1480_clockevent_init();
+	local_irq_enable();
+}
+
+/*
+ * Setup the PC, SP, and GP of a secondary processor and start it
+ * running!
+ */
+static int bcm1480_boot_secondary(int cpu, struct task_struct *idle)
+{
+	int retval;
+
+	retval = cfe_cpu_start(cpu_logical_map(cpu), &smp_bootstrap,
+			       __KSTK_TOS(idle),
+			       (unsigned long)task_thread_info(idle), 0);
+	if (retval != 0)
+		printk("cfe_start_cpu(%i) returned %i\n" , cpu, retval);
+	return retval;
+}
+
+/*
+ * Use CFE to find out how many CPUs are available, setting up
+ * cpu_possible_mask and the logical/physical mappings.
+ * XXXKW will the boot CPU ever not be physical 0?
+ *
+ * Common setup before any secondaries are started
+ */
+static void __init bcm1480_smp_setup(void)
+{
+	int i, num;
+
+	init_cpu_possible(cpumask_of(0));
+	__cpu_number_map[0] = 0;
+	__cpu_logical_map[0] = 0;
+
+	for (i = 1, num = 0; i < NR_CPUS; i++) {
+		if (cfe_cpu_stop(i) == 0) {
+			set_cpu_possible(i, true);
+			__cpu_number_map[i] = ++num;
+			__cpu_logical_map[num] = i;
+		}
+	}
+	printk(KERN_INFO "Detected %i available secondary CPU(s)\n", num);
+}
+
+static void __init bcm1480_prepare_cpus(unsigned int max_cpus)
+{
+}
+
+const struct plat_smp_ops bcm1480_smp_ops = {
+	.send_ipi_single	= bcm1480_send_ipi_single,
+	.send_ipi_mask		= bcm1480_send_ipi_mask,
+	.init_secondary		= bcm1480_init_secondary,
+	.smp_finish		= bcm1480_smp_finish,
+	.boot_secondary		= bcm1480_boot_secondary,
+	.smp_setup		= bcm1480_smp_setup,
+	.prepare_cpus		= bcm1480_prepare_cpus,
+};
+
+void bcm1480_mailbox_interrupt(void)
+{
+	int cpu = smp_processor_id();
+	int irq = K_BCM1480_INT_MBOX_0_0;
+	unsigned int action;
+
+	kstat_incr_irq_this_cpu(irq);
+	/* Load the mailbox register to figure out what we're supposed to do */
+	action = (__raw_readq(mailbox_0_regs[cpu]) >> 48) & 0xffff;
+
+	/* Clear the mailbox to clear the interrupt */
+	__raw_writeq(((u64)action)<<48, mailbox_0_clear_regs[cpu]);
+
+	if (action & SMP_RESCHEDULE_YOURSELF)
+		scheduler_ipi();
+
+	if (action & SMP_CALL_FUNCTION) {
+		irq_enter();
+		generic_smp_call_function_interrupt();
+		irq_exit();
+	}
+}
diff --git a/arch/mips/sibyte/bcm1480/time.c b/arch/mips/sibyte/bcm1480/time.c
new file mode 100644
index 000000000..e6450d79f
--- /dev/null
+++ b/arch/mips/sibyte/bcm1480/time.c
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2000,2001,2004 Broadcom Corporation
+ */
+#include <linux/init.h>
+
+extern void sb1480_clockevent_init(void);
+extern void sb1480_clocksource_init(void);
+
+void __init plat_time_init(void)
+{
+	sb1480_clocksource_init();
+	sb1480_clockevent_init();
+}
diff --git a/arch/mips/sibyte/common/Makefile b/arch/mips/sibyte/common/Makefile
new file mode 100644
index 000000000..57f670aa1
--- /dev/null
+++ b/arch/mips/sibyte/common/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0-only
+obj-y := cfe.o
+obj-$(CONFIG_SWIOTLB)			+= dma.o
+obj-$(CONFIG_SIBYTE_BUS_WATCHER)	+= bus_watcher.o
+obj-$(CONFIG_SIBYTE_CFE_CONSOLE)	+= cfe_console.o
+obj-$(CONFIG_SIBYTE_TBPROF)		+= sb_tbprof.o
diff --git a/arch/mips/sibyte/common/bus_watcher.c b/arch/mips/sibyte/common/bus_watcher.c
new file mode 100644
index 000000000..d43291473
--- /dev/null
+++ b/arch/mips/sibyte/common/bus_watcher.c
@@ -0,0 +1,228 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2002,2003 Broadcom Corporation
+ */
+
+/*
+ * The Bus Watcher monitors internal bus transactions and maintains
+ * counts of transactions with error status, logging details and
+ * causing one of several interrupts.  This driver provides a handler
+ * for those interrupts which aggregates the counts (to avoid
+ * saturating the 8-bit counters) and provides a presence in
+ * /proc/bus_watcher if PROC_FS is on.
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/interrupt.h>
+#include <linux/sched.h>
+#include <linux/proc_fs.h>
+#include <linux/seq_file.h>
+#include <asm/io.h>
+
+#include <asm/sibyte/sb1250.h>
+#include <asm/sibyte/sb1250_regs.h>
+#include <asm/sibyte/sb1250_int.h>
+#include <asm/sibyte/sb1250_scd.h>
+#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80)
+#include <asm/sibyte/bcm1480_regs.h>
+#endif
+
+
+struct bw_stats_struct {
+	uint64_t status;
+	uint32_t l2_err;
+	uint32_t memio_err;
+	int status_printed;
+	unsigned long l2_cor_d;
+	unsigned long l2_bad_d;
+	unsigned long l2_cor_t;
+	unsigned long l2_bad_t;
+	unsigned long mem_cor_d;
+	unsigned long mem_bad_d;
+	unsigned long bus_error;
+} bw_stats;
+
+
+static void print_summary(uint32_t status, uint32_t l2_err,
+			  uint32_t memio_err)
+{
+	printk("Bus watcher error counters: %08x %08x\n", l2_err, memio_err);
+	printk("\nLast recorded signature:\n");
+	printk("Request %02x from %d, answered by %d with Dcode %d\n",
+	       (unsigned int)(G_SCD_BERR_TID(status) & 0x3f),
+	       (int)(G_SCD_BERR_TID(status) >> 6),
+	       (int)G_SCD_BERR_RID(status),
+	       (int)G_SCD_BERR_DCODE(status));
+}
+
+/*
+ * check_bus_watcher is exported for use in situations where we want
+ * to see the most recent status of the bus watcher, which might have
+ * already been destructively read out of the registers.
+ *
+ * notes: this is currently used by the cache error handler
+ *	  should provide locking against the interrupt handler
+ */
+void check_bus_watcher(void)
+{
+	u32 status, l2_err, memio_err;
+
+#if defined(CONFIG_SIBYTE_BCM112X) || defined(CONFIG_SIBYTE_SB1250)
+	/* Use non-destructive register */
+	status = csr_in32(IOADDR(A_SCD_BUS_ERR_STATUS_DEBUG));
+#elif defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80)
+	/* Use non-destructive register */
+	/* Same as 1250 except BUS_ERR_STATUS_DEBUG is in a different place. */
+	status = csr_in32(IOADDR(A_BCM1480_BUS_ERR_STATUS_DEBUG));
+#else
+#error bus watcher being built for unknown Sibyte SOC!
+#endif
+	if (!(status & 0x7fffffff)) {
+		printk("Using last values reaped by bus watcher driver\n");
+		status = bw_stats.status;
+		l2_err = bw_stats.l2_err;
+		memio_err = bw_stats.memio_err;
+	} else {
+		l2_err = csr_in32(IOADDR(A_BUS_L2_ERRORS));
+		memio_err = csr_in32(IOADDR(A_BUS_MEM_IO_ERRORS));
+	}
+	if (status & ~(1UL << 31))
+		print_summary(status, l2_err, memio_err);
+	else
+		printk("Bus watcher indicates no error\n");
+}
+
+#ifdef CONFIG_PROC_FS
+
+/* For simplicity, I want to assume a single read is required each
+   time */
+static int bw_proc_show(struct seq_file *m, void *v)
+{
+	struct bw_stats_struct *stats = m->private;
+
+	seq_puts(m, "SiByte Bus Watcher statistics\n");
+	seq_puts(m, "-----------------------------\n");
+	seq_printf(m, "L2-d-cor %8ld\nL2-d-bad %8ld\n",
+		   stats->l2_cor_d, stats->l2_bad_d);
+	seq_printf(m, "L2-t-cor %8ld\nL2-t-bad %8ld\n",
+		   stats->l2_cor_t, stats->l2_bad_t);
+	seq_printf(m, "MC-d-cor %8ld\nMC-d-bad %8ld\n",
+		   stats->mem_cor_d, stats->mem_bad_d);
+	seq_printf(m, "IO-err   %8ld\n", stats->bus_error);
+	seq_puts(m, "\nLast recorded signature:\n");
+	seq_printf(m, "Request %02x from %d, answered by %d with Dcode %d\n",
+		   (unsigned int)(G_SCD_BERR_TID(stats->status) & 0x3f),
+		   (int)(G_SCD_BERR_TID(stats->status) >> 6),
+		   (int)G_SCD_BERR_RID(stats->status),
+		   (int)G_SCD_BERR_DCODE(stats->status));
+	/* XXXKW indicate multiple errors between printings, or stats
+	   collection (or both)? */
+	if (stats->status & M_SCD_BERR_MULTERRS)
+		seq_puts(m, "Multiple errors observed since last check.\n");
+	if (stats->status_printed) {
+		seq_puts(m, "(no change since last printing)\n");
+	} else {
+		stats->status_printed = 1;
+	}
+
+	return 0;
+}
+
+static void create_proc_decoder(struct bw_stats_struct *stats)
+{
+	struct proc_dir_entry *ent;
+
+	ent = proc_create_single_data("bus_watcher", S_IWUSR | S_IRUGO, NULL,
+			bw_proc_show, stats);
+	if (!ent) {
+		printk(KERN_INFO "Unable to initialize bus_watcher /proc entry\n");
+		return;
+	}
+}
+
+#endif /* CONFIG_PROC_FS */
+
+/*
+ * sibyte_bw_int - handle bus watcher interrupts and accumulate counts
+ *
+ * notes: possible re-entry due to multiple sources
+ *	  should check/indicate saturation
+ */
+static irqreturn_t sibyte_bw_int(int irq, void *data)
+{
+	struct bw_stats_struct *stats = data;
+	unsigned long cntr;
+#ifdef CONFIG_SIBYTE_BW_TRACE
+	int i;
+#endif
+
+#ifdef CONFIG_SIBYTE_BW_TRACE
+	csr_out32(M_SCD_TRACE_CFG_FREEZE, IOADDR(A_SCD_TRACE_CFG));
+	csr_out32(M_SCD_TRACE_CFG_START_READ, IOADDR(A_SCD_TRACE_CFG));
+
+	for (i=0; i<256*6; i++)
+		printk("%016llx\n",
+		       (long long)__raw_readq(IOADDR(A_SCD_TRACE_READ)));
+
+	csr_out32(M_SCD_TRACE_CFG_RESET, IOADDR(A_SCD_TRACE_CFG));
+	csr_out32(M_SCD_TRACE_CFG_START, IOADDR(A_SCD_TRACE_CFG));
+#endif
+
+	/* Destructive read, clears register and interrupt */
+	stats->status = csr_in32(IOADDR(A_SCD_BUS_ERR_STATUS));
+	stats->status_printed = 0;
+
+	stats->l2_err = cntr = csr_in32(IOADDR(A_BUS_L2_ERRORS));
+	stats->l2_cor_d += G_SCD_L2ECC_CORR_D(cntr);
+	stats->l2_bad_d += G_SCD_L2ECC_BAD_D(cntr);
+	stats->l2_cor_t += G_SCD_L2ECC_CORR_T(cntr);
+	stats->l2_bad_t += G_SCD_L2ECC_BAD_T(cntr);
+	csr_out32(0, IOADDR(A_BUS_L2_ERRORS));
+
+	stats->memio_err = cntr = csr_in32(IOADDR(A_BUS_MEM_IO_ERRORS));
+	stats->mem_cor_d += G_SCD_MEM_ECC_CORR(cntr);
+	stats->mem_bad_d += G_SCD_MEM_ECC_BAD(cntr);
+	stats->bus_error += G_SCD_MEM_BUSERR(cntr);
+	csr_out32(0, IOADDR(A_BUS_MEM_IO_ERRORS));
+
+	return IRQ_HANDLED;
+}
+
+int __init sibyte_bus_watcher(void)
+{
+	memset(&bw_stats, 0, sizeof(struct bw_stats_struct));
+	bw_stats.status_printed = 1;
+
+	if (request_irq(K_INT_BAD_ECC, sibyte_bw_int, 0, "Bus watcher", &bw_stats)) {
+		printk("Failed to register bus watcher BAD_ECC irq\n");
+		return -1;
+	}
+	if (request_irq(K_INT_COR_ECC, sibyte_bw_int, 0, "Bus watcher", &bw_stats)) {
+		free_irq(K_INT_BAD_ECC, &bw_stats);
+		printk("Failed to register bus watcher COR_ECC irq\n");
+		return -1;
+	}
+	if (request_irq(K_INT_IO_BUS, sibyte_bw_int, 0, "Bus watcher", &bw_stats)) {
+		free_irq(K_INT_BAD_ECC, &bw_stats);
+		free_irq(K_INT_COR_ECC, &bw_stats);
+		printk("Failed to register bus watcher IO_BUS irq\n");
+		return -1;
+	}
+
+#ifdef CONFIG_PROC_FS
+	create_proc_decoder(&bw_stats);
+#endif
+
+#ifdef CONFIG_SIBYTE_BW_TRACE
+	csr_out32((M_SCD_TRSEQ_ASAMPLE | M_SCD_TRSEQ_DSAMPLE |
+		   K_SCD_TRSEQ_TRIGGER_ALL),
+		  IOADDR(A_SCD_TRACE_SEQUENCE_0));
+	csr_out32(M_SCD_TRACE_CFG_RESET, IOADDR(A_SCD_TRACE_CFG));
+	csr_out32(M_SCD_TRACE_CFG_START, IOADDR(A_SCD_TRACE_CFG));
+#endif
+
+	return 0;
+}
+
+device_initcall(sibyte_bus_watcher);
diff --git a/arch/mips/sibyte/common/cfe.c b/arch/mips/sibyte/common/cfe.c
new file mode 100644
index 000000000..1a504294d
--- /dev/null
+++ b/arch/mips/sibyte/common/cfe.c
@@ -0,0 +1,324 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2000, 2001, 2002, 2003 Broadcom Corporation
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/linkage.h>
+#include <linux/mm.h>
+#include <linux/memblock.h>
+#include <linux/pm.h>
+#include <linux/smp.h>
+
+#include <asm/bootinfo.h>
+#include <asm/reboot.h>
+#include <asm/setup.h>
+#include <asm/sibyte/board.h>
+#include <asm/smp-ops.h>
+
+#include <asm/fw/cfe/cfe_api.h>
+#include <asm/fw/cfe/cfe_error.h>
+
+/* Max ram addressable in 32-bit segments */
+#ifdef CONFIG_64BIT
+#define MAX_RAM_SIZE (~0ULL)
+#else
+#ifdef CONFIG_HIGHMEM
+#ifdef CONFIG_PHYS_ADDR_T_64BIT
+#define MAX_RAM_SIZE (~0ULL)
+#else
+#define MAX_RAM_SIZE (0xffffffffULL)
+#endif
+#else
+#define MAX_RAM_SIZE (0x1fffffffULL)
+#endif
+#endif
+
+#define SIBYTE_MAX_MEM_REGIONS 8
+phys_addr_t board_mem_region_addrs[SIBYTE_MAX_MEM_REGIONS];
+phys_addr_t board_mem_region_sizes[SIBYTE_MAX_MEM_REGIONS];
+unsigned int board_mem_region_count;
+
+int cfe_cons_handle;
+
+#ifdef CONFIG_BLK_DEV_INITRD
+extern unsigned long initrd_start, initrd_end;
+#endif
+
+static void __noreturn cfe_linux_exit(void *arg)
+{
+	int warm = *(int *)arg;
+
+	if (smp_processor_id()) {
+		static int reboot_smp;
+
+		/* Don't repeat the process from another CPU */
+		if (!reboot_smp) {
+			/* Get CPU 0 to do the cfe_exit */
+			reboot_smp = 1;
+			smp_call_function(cfe_linux_exit, arg, 0);
+		}
+	} else {
+		printk("Passing control back to CFE...\n");
+		cfe_exit(warm, 0);
+		printk("cfe_exit returned??\n");
+	}
+	while (1);
+}
+
+static void __noreturn cfe_linux_restart(char *command)
+{
+	static const int zero;
+
+	cfe_linux_exit((void *)&zero);
+}
+
+static void __noreturn cfe_linux_halt(void)
+{
+	static const int one = 1;
+
+	cfe_linux_exit((void *)&one);
+}
+
+static __init void prom_meminit(void)
+{
+	u64 addr, size, type; /* regardless of PHYS_ADDR_T_64BIT */
+	int mem_flags = 0;
+	unsigned int idx;
+	int rd_flag;
+#ifdef CONFIG_BLK_DEV_INITRD
+	unsigned long initrd_pstart;
+	unsigned long initrd_pend;
+
+	initrd_pstart = CPHYSADDR(initrd_start);
+	initrd_pend = CPHYSADDR(initrd_end);
+	if (initrd_start &&
+	    ((initrd_pstart > MAX_RAM_SIZE)
+	     || (initrd_pend > MAX_RAM_SIZE))) {
+		panic("initrd out of addressable memory");
+	}
+
+#endif /* INITRD */
+
+	for (idx = 0; cfe_enummem(idx, mem_flags, &addr, &size, &type) != CFE_ERR_NOMORE;
+	     idx++) {
+		rd_flag = 0;
+		if (type == CFE_MI_AVAILABLE) {
+			/*
+			 * See if this block contains (any portion of) the
+			 * ramdisk
+			 */
+#ifdef CONFIG_BLK_DEV_INITRD
+			if (initrd_start) {
+				if ((initrd_pstart > addr) &&
+				    (initrd_pstart < (addr + size))) {
+					memblock_add(addr,
+						     initrd_pstart - addr);
+					rd_flag = 1;
+				}
+				if ((initrd_pend > addr) &&
+				    (initrd_pend < (addr + size))) {
+					memblock_add(initrd_pend,
+						(addr + size) - initrd_pend);
+					rd_flag = 1;
+				}
+			}
+#endif
+			if (!rd_flag) {
+				if (addr > MAX_RAM_SIZE)
+					continue;
+				if (addr+size > MAX_RAM_SIZE)
+					size = MAX_RAM_SIZE - (addr+size) + 1;
+				/*
+				 * memcpy/__copy_user prefetch, which
+				 * will cause a bus error for
+				 * KSEG/KUSEG addrs not backed by RAM.
+				 * Hence, reserve some padding for the
+				 * prefetch distance.
+				 */
+				if (size > 512)
+					size -= 512;
+				memblock_add(addr, size);
+			}
+			board_mem_region_addrs[board_mem_region_count] = addr;
+			board_mem_region_sizes[board_mem_region_count] = size;
+			board_mem_region_count++;
+			if (board_mem_region_count ==
+			    SIBYTE_MAX_MEM_REGIONS) {
+				/*
+				 * Too many regions.  Need to configure more
+				 */
+				while(1);
+			}
+		}
+	}
+#ifdef CONFIG_BLK_DEV_INITRD
+	if (initrd_start) {
+		memblock_add(initrd_pstart, initrd_pend - initrd_pstart);
+		memblock_reserve(initrd_pstart, initrd_pend - initrd_pstart);
+	}
+#endif
+}
+
+#ifdef CONFIG_BLK_DEV_INITRD
+static int __init initrd_setup(char *str)
+{
+	char rdarg[64];
+	int idx;
+	char *tmp, *endptr;
+	unsigned long initrd_size;
+
+	/* Make a copy of the initrd argument so we can smash it up here */
+	for (idx = 0; idx < sizeof(rdarg)-1; idx++) {
+		if (!str[idx] || (str[idx] == ' ')) break;
+		rdarg[idx] = str[idx];
+	}
+
+	rdarg[idx] = 0;
+	str = rdarg;
+
+	/*
+	 *Initrd location comes in the form "<hex size of ramdisk in bytes>@<location in memory>"
+	 *  e.g. initrd=3abfd@80010000.	 This is set up by the loader.
+	 */
+	for (tmp = str; *tmp != '@'; tmp++) {
+		if (!*tmp) {
+			goto fail;
+		}
+	}
+	*tmp = 0;
+	tmp++;
+	if (!*tmp) {
+		goto fail;
+	}
+	initrd_size = simple_strtoul(str, &endptr, 16);
+	if (*endptr) {
+		*(tmp-1) = '@';
+		goto fail;
+	}
+	*(tmp-1) = '@';
+	initrd_start = simple_strtoul(tmp, &endptr, 16);
+	if (*endptr) {
+		goto fail;
+	}
+	initrd_end = initrd_start + initrd_size;
+	printk("Found initrd of %lx@%lx\n", initrd_size, initrd_start);
+	return 1;
+ fail:
+	printk("Bad initrd argument.  Disabling initrd\n");
+	initrd_start = 0;
+	initrd_end = 0;
+	return 1;
+}
+
+#endif
+
+extern const struct plat_smp_ops sb_smp_ops;
+extern const struct plat_smp_ops bcm1480_smp_ops;
+
+/*
+ * prom_init is called just after the cpu type is determined, from setup_arch()
+ */
+void __init prom_init(void)
+{
+	uint64_t cfe_ept, cfe_handle;
+	unsigned int cfe_eptseal;
+	int argc = fw_arg0;
+	char **envp = (char **) fw_arg2;
+	int *prom_vec = (int *) fw_arg3;
+
+	_machine_restart   = cfe_linux_restart;
+	_machine_halt	   = cfe_linux_halt;
+	pm_power_off = cfe_linux_halt;
+
+	/*
+	 * Check if a loader was used; if NOT, the 4 arguments are
+	 * what CFE gives us (handle, 0, EPT and EPTSEAL)
+	 */
+	if (argc < 0) {
+		cfe_handle = (uint64_t)(long)argc;
+		cfe_ept = (long)envp;
+		cfe_eptseal = (uint32_t)(unsigned long)prom_vec;
+	} else {
+		if ((int32_t)(long)prom_vec < 0) {
+			/*
+			 * Old loader; all it gives us is the handle,
+			 * so use the "known" entrypoint and assume
+			 * the seal.
+			 */
+			cfe_handle = (uint64_t)(long)prom_vec;
+			cfe_ept = (uint64_t)((int32_t)0x9fc00500);
+			cfe_eptseal = CFE_EPTSEAL;
+		} else {
+			/*
+			 * Newer loaders bundle the handle/ept/eptseal
+			 * Note: prom_vec is in the loader's useg
+			 * which is still alive in the TLB.
+			 */
+			cfe_handle = (uint64_t)((int32_t *)prom_vec)[0];
+			cfe_ept = (uint64_t)((int32_t *)prom_vec)[2];
+			cfe_eptseal = (unsigned int)((uint32_t *)prom_vec)[3];
+		}
+	}
+	if (cfe_eptseal != CFE_EPTSEAL) {
+		/* too early for panic to do any good */
+		printk("CFE's entrypoint seal doesn't match. Spinning.");
+		while (1) ;
+	}
+	cfe_init(cfe_handle, cfe_ept);
+	/*
+	 * Get the handle for (at least) prom_putchar, possibly for
+	 * boot console
+	 */
+	cfe_cons_handle = cfe_getstdhandle(CFE_STDHANDLE_CONSOLE);
+	if (cfe_getenv("LINUX_CMDLINE", arcs_cmdline, COMMAND_LINE_SIZE) < 0) {
+		if (argc >= 0) {
+			/* The loader should have set the command line */
+			/* too early for panic to do any good */
+			printk("LINUX_CMDLINE not defined in cfe.");
+			while (1) ;
+		}
+	}
+
+#ifdef CONFIG_BLK_DEV_INITRD
+	{
+		char *ptr;
+		/* Need to find out early whether we've got an initrd.	So scan
+		   the list looking now */
+		for (ptr = arcs_cmdline; *ptr; ptr++) {
+			while (*ptr == ' ') {
+				ptr++;
+			}
+			if (!strncmp(ptr, "initrd=", 7)) {
+				initrd_setup(ptr+7);
+				break;
+			} else {
+				while (*ptr && (*ptr != ' ')) {
+					ptr++;
+				}
+			}
+		}
+	}
+#endif /* CONFIG_BLK_DEV_INITRD */
+
+	/* Not sure this is needed, but it's the safe way. */
+	arcs_cmdline[COMMAND_LINE_SIZE-1] = 0;
+
+	prom_meminit();
+
+#if defined(CONFIG_SIBYTE_BCM112X) || defined(CONFIG_SIBYTE_SB1250)
+	register_smp_ops(&sb_smp_ops);
+#endif
+#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80)
+	register_smp_ops(&bcm1480_smp_ops);
+#endif
+}
+
+void prom_putchar(char c)
+{
+	int ret;
+
+	while ((ret = cfe_write(cfe_cons_handle, &c, 1)) == 0)
+		;
+}
diff --git a/arch/mips/sibyte/common/cfe_console.c b/arch/mips/sibyte/common/cfe_console.c
new file mode 100644
index 000000000..8af7b41f7
--- /dev/null
+++ b/arch/mips/sibyte/common/cfe_console.c
@@ -0,0 +1,81 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/console.h>
+
+#include <asm/sibyte/board.h>
+
+#include <asm/fw/cfe/cfe_api.h>
+#include <asm/fw/cfe/cfe_error.h>
+
+extern int cfe_cons_handle;
+
+static void cfe_console_write(struct console *cons, const char *str,
+		       unsigned int count)
+{
+	int i, last, written;
+
+	for (i=0, last=0; i<count; i++) {
+		if (!str[i])
+			/* XXXKW can/should this ever happen? */
+			return;
+		if (str[i] == '\n') {
+			do {
+				written = cfe_write(cfe_cons_handle, &str[last], i-last);
+				if (written < 0)
+					;
+				last += written;
+			} while (last < i);
+			while (cfe_write(cfe_cons_handle, "\r", 1) <= 0)
+				;
+		}
+	}
+	if (last != count) {
+		do {
+			written = cfe_write(cfe_cons_handle, &str[last], count-last);
+			if (written < 0)
+				;
+			last += written;
+		} while (last < count);
+	}
+
+}
+
+static int cfe_console_setup(struct console *cons, char *str)
+{
+	char consdev[32];
+	/* XXXKW think about interaction with 'console=' cmdline arg */
+	/* If none of the console options are configured, the build will break. */
+	if (cfe_getenv("BOOT_CONSOLE", consdev, 32) >= 0) {
+#ifdef CONFIG_SERIAL_SB1250_DUART
+		if (!strcmp(consdev, "uart0")) {
+			setleds("u0cn");
+		} else if (!strcmp(consdev, "uart1")) {
+			setleds("u1cn");
+		} else
+#endif
+#ifdef CONFIG_VGA_CONSOLE
+		       if (!strcmp(consdev, "pcconsole0")) {
+				setleds("pccn");
+		} else
+#endif
+			return -ENODEV;
+	}
+	return 0;
+}
+
+static struct console sb1250_cfe_cons = {
+	.name		= "cfe",
+	.write		= cfe_console_write,
+	.setup		= cfe_console_setup,
+	.flags		= CON_PRINTBUFFER,
+	.index		= -1,
+};
+
+static int __init sb1250_cfe_console_init(void)
+{
+	register_console(&sb1250_cfe_cons);
+	return 0;
+}
+
+console_initcall(sb1250_cfe_console_init);
diff --git a/arch/mips/sibyte/common/dma.c b/arch/mips/sibyte/common/dma.c
new file mode 100644
index 000000000..c5c2c782a
--- /dev/null
+++ b/arch/mips/sibyte/common/dma.c
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ *	DMA support for Broadcom SiByte platforms.
+ *
+ *	Copyright (c) 2018  Maciej W. Rozycki
+ */
+
+#include <linux/swiotlb.h>
+#include <asm/bootinfo.h>
+
+void __init plat_swiotlb_setup(void)
+{
+	swiotlb_init(true, SWIOTLB_VERBOSE);
+}
diff --git a/arch/mips/sibyte/common/sb_tbprof.c b/arch/mips/sibyte/common/sb_tbprof.c
new file mode 100644
index 000000000..bc47681e8
--- /dev/null
+++ b/arch/mips/sibyte/common/sb_tbprof.c
@@ -0,0 +1,595 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *
+ * Copyright (C) 2001, 2002, 2003 Broadcom Corporation
+ * Copyright (C) 2007 Ralf Baechle <ralf@linux-mips.org>
+ * Copyright (C) 2007 MIPS Technologies, Inc.
+ *    written by Ralf Baechle <ralf@linux-mips.org>
+ */
+
+#undef DEBUG
+
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/sched.h>
+#include <linux/vmalloc.h>
+#include <linux/fs.h>
+#include <linux/errno.h>
+#include <linux/wait.h>
+#include <asm/io.h>
+#include <asm/sibyte/sb1250.h>
+
+#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80)
+#include <asm/sibyte/bcm1480_regs.h>
+#include <asm/sibyte/bcm1480_scd.h>
+#include <asm/sibyte/bcm1480_int.h>
+#elif defined(CONFIG_SIBYTE_SB1250) || defined(CONFIG_SIBYTE_BCM112X)
+#include <asm/sibyte/sb1250_regs.h>
+#include <asm/sibyte/sb1250_scd.h>
+#include <asm/sibyte/sb1250_int.h>
+#else
+#error invalid SiByte UART configuration
+#endif
+
+#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80)
+#undef K_INT_TRACE_FREEZE
+#define K_INT_TRACE_FREEZE K_BCM1480_INT_TRACE_FREEZE
+#undef K_INT_PERF_CNT
+#define K_INT_PERF_CNT K_BCM1480_INT_PERF_CNT
+#endif
+
+#include <linux/uaccess.h>
+
+#define SBPROF_TB_MAJOR 240
+
+typedef u64 tb_sample_t[6*256];
+
+enum open_status {
+	SB_CLOSED,
+	SB_OPENING,
+	SB_OPEN
+};
+
+struct sbprof_tb {
+	wait_queue_head_t	tb_sync;
+	wait_queue_head_t	tb_read;
+	struct mutex		lock;
+	enum open_status	open;
+	tb_sample_t		*sbprof_tbbuf;
+	int			next_tb_sample;
+
+	volatile int		tb_enable;
+	volatile int		tb_armed;
+
+};
+
+static struct sbprof_tb sbp;
+
+#define MAX_SAMPLE_BYTES (24*1024*1024)
+#define MAX_TBSAMPLE_BYTES (12*1024*1024)
+
+#define MAX_SAMPLES (MAX_SAMPLE_BYTES/sizeof(u_int32_t))
+#define TB_SAMPLE_SIZE (sizeof(tb_sample_t))
+#define MAX_TB_SAMPLES (MAX_TBSAMPLE_BYTES/TB_SAMPLE_SIZE)
+
+/* ioctls */
+#define SBPROF_ZBSTART		_IOW('s', 0, int)
+#define SBPROF_ZBSTOP		_IOW('s', 1, int)
+#define SBPROF_ZBWAITFULL	_IOW('s', 2, int)
+
+/*
+ * Routines for using 40-bit SCD cycle counter
+ *
+ * Client responsible for either handling interrupts or making sure
+ * the cycles counter never saturates, e.g., by doing
+ * zclk_timer_init(0) at least every 2^40 - 1 ZCLKs.
+ */
+
+/*
+ * Configures SCD counter 0 to count ZCLKs starting from val;
+ * Configures SCD counters1,2,3 to count nothing.
+ * Must not be called while gathering ZBbus profiles.
+ */
+
+#define zclk_timer_init(val) \
+  __asm__ __volatile__ (".set push;" \
+			".set mips64;" \
+			"la   $8, 0xb00204c0;" /* SCD perf_cnt_cfg */ \
+			"sd   %0, 0x10($8);"   /* write val to counter0 */ \
+			"sd   %1, 0($8);"      /* config counter0 for zclks*/ \
+			".set pop" \
+			: /* no outputs */ \
+						     /* enable, counter0 */ \
+			: /* inputs */ "r"(val), "r" ((1ULL << 33) | 1ULL) \
+			: /* modifies */ "$8" )
+
+
+/* Reads SCD counter 0 and puts result in value
+   unsigned long long val; */
+#define zclk_get(val) \
+  __asm__ __volatile__ (".set push;" \
+			".set mips64;" \
+			"la   $8, 0xb00204c0;" /* SCD perf_cnt_cfg */ \
+			"ld   %0, 0x10($8);"   /* write val to counter0 */ \
+			".set pop" \
+			: /* outputs */ "=r"(val) \
+			: /* inputs */ \
+			: /* modifies */ "$8" )
+
+#define DEVNAME "sb_tbprof"
+
+#define TB_FULL (sbp.next_tb_sample == MAX_TB_SAMPLES)
+
+/*
+ * Support for ZBbus sampling using the trace buffer
+ *
+ * We use the SCD performance counter interrupt, caused by a Zclk counter
+ * overflow, to trigger the start of tracing.
+ *
+ * We set the trace buffer to sample everything and freeze on
+ * overflow.
+ *
+ * We map the interrupt for trace_buffer_freeze to handle it on CPU 0.
+ *
+ */
+
+static u64 tb_period;
+
+static void arm_tb(void)
+{
+	u64 scdperfcnt;
+	u64 next = (1ULL << 40) - tb_period;
+	u64 tb_options = M_SCD_TRACE_CFG_FREEZE_FULL;
+
+	/*
+	 * Generate an SCD_PERFCNT interrupt in TB_PERIOD Zclks to
+	 * trigger start of trace.  XXX vary sampling period
+	 */
+	__raw_writeq(0, IOADDR(A_SCD_PERF_CNT_1));
+	scdperfcnt = __raw_readq(IOADDR(A_SCD_PERF_CNT_CFG));
+
+	/*
+	 * Unfortunately, in Pass 2 we must clear all counters to knock down
+	 * a previous interrupt request.  This means that bus profiling
+	 * requires ALL of the SCD perf counters.
+	 */
+#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80)
+	__raw_writeq((scdperfcnt & ~M_SPC_CFG_SRC1) |
+						/* keep counters 0,2,3,4,5,6,7 as is */
+		     V_SPC_CFG_SRC1(1),		/* counter 1 counts cycles */
+		     IOADDR(A_BCM1480_SCD_PERF_CNT_CFG0));
+	__raw_writeq(
+		     M_SPC_CFG_ENABLE |		/* enable counting */
+		     M_SPC_CFG_CLEAR |		/* clear all counters */
+		     V_SPC_CFG_SRC1(1),		/* counter 1 counts cycles */
+		     IOADDR(A_BCM1480_SCD_PERF_CNT_CFG1));
+#else
+	__raw_writeq((scdperfcnt & ~M_SPC_CFG_SRC1) |
+						/* keep counters 0,2,3 as is */
+		     M_SPC_CFG_ENABLE |		/* enable counting */
+		     M_SPC_CFG_CLEAR |		/* clear all counters */
+		     V_SPC_CFG_SRC1(1),		/* counter 1 counts cycles */
+		     IOADDR(A_SCD_PERF_CNT_CFG));
+#endif
+	__raw_writeq(next, IOADDR(A_SCD_PERF_CNT_1));
+	/* Reset the trace buffer */
+	__raw_writeq(M_SCD_TRACE_CFG_RESET, IOADDR(A_SCD_TRACE_CFG));
+#if 0 && defined(M_SCD_TRACE_CFG_FORCECNT)
+	/* XXXKW may want to expose control to the data-collector */
+	tb_options |= M_SCD_TRACE_CFG_FORCECNT;
+#endif
+	__raw_writeq(tb_options, IOADDR(A_SCD_TRACE_CFG));
+	sbp.tb_armed = 1;
+}
+
+static irqreturn_t sbprof_tb_intr(int irq, void *dev_id)
+{
+	int i;
+
+	pr_debug(DEVNAME ": tb_intr\n");
+
+	if (sbp.next_tb_sample < MAX_TB_SAMPLES) {
+		/* XXX should use XKPHYS to make writes bypass L2 */
+		u64 *p = sbp.sbprof_tbbuf[sbp.next_tb_sample++];
+		/* Read out trace */
+		__raw_writeq(M_SCD_TRACE_CFG_START_READ,
+			     IOADDR(A_SCD_TRACE_CFG));
+		__asm__ __volatile__ ("sync" : : : "memory");
+		/* Loop runs backwards because bundles are read out in reverse order */
+		for (i = 256 * 6; i > 0; i -= 6) {
+			/* Subscripts decrease to put bundle in the order */
+			/*   t0 lo, t0 hi, t1 lo, t1 hi, t2 lo, t2 hi */
+			p[i - 1] = __raw_readq(IOADDR(A_SCD_TRACE_READ));
+			/* read t2 hi */
+			p[i - 2] = __raw_readq(IOADDR(A_SCD_TRACE_READ));
+			/* read t2 lo */
+			p[i - 3] = __raw_readq(IOADDR(A_SCD_TRACE_READ));
+			/* read t1 hi */
+			p[i - 4] = __raw_readq(IOADDR(A_SCD_TRACE_READ));
+			/* read t1 lo */
+			p[i - 5] = __raw_readq(IOADDR(A_SCD_TRACE_READ));
+			/* read t0 hi */
+			p[i - 6] = __raw_readq(IOADDR(A_SCD_TRACE_READ));
+			/* read t0 lo */
+		}
+		if (!sbp.tb_enable) {
+			pr_debug(DEVNAME ": tb_intr shutdown\n");
+			__raw_writeq(M_SCD_TRACE_CFG_RESET,
+				     IOADDR(A_SCD_TRACE_CFG));
+			sbp.tb_armed = 0;
+			wake_up_interruptible(&sbp.tb_sync);
+		} else {
+			/* knock down current interrupt and get another one later */
+			arm_tb();
+		}
+	} else {
+		/* No more trace buffer samples */
+		pr_debug(DEVNAME ": tb_intr full\n");
+		__raw_writeq(M_SCD_TRACE_CFG_RESET, IOADDR(A_SCD_TRACE_CFG));
+		sbp.tb_armed = 0;
+		if (!sbp.tb_enable)
+			wake_up_interruptible(&sbp.tb_sync);
+		wake_up_interruptible(&sbp.tb_read);
+	}
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t sbprof_pc_intr(int irq, void *dev_id)
+{
+	printk(DEVNAME ": unexpected pc_intr");
+	return IRQ_NONE;
+}
+
+/*
+ * Requires: Already called zclk_timer_init with a value that won't
+ *	     saturate 40 bits.	No subsequent use of SCD performance counters
+ *	     or trace buffer.
+ */
+
+static int sbprof_zbprof_start(struct file *filp)
+{
+	u64 scdperfcnt;
+	int err;
+
+	if (xchg(&sbp.tb_enable, 1))
+		return -EBUSY;
+
+	pr_debug(DEVNAME ": starting\n");
+
+	sbp.next_tb_sample = 0;
+	filp->f_pos = 0;
+
+	err = request_irq(K_INT_TRACE_FREEZE, sbprof_tb_intr, 0,
+			  DEVNAME " trace freeze", &sbp);
+	if (err)
+		return -EBUSY;
+
+	/* Make sure there isn't a perf-cnt interrupt waiting */
+	scdperfcnt = __raw_readq(IOADDR(A_SCD_PERF_CNT_CFG));
+	/* Disable and clear counters, override SRC_1 */
+	__raw_writeq((scdperfcnt & ~(M_SPC_CFG_SRC1 | M_SPC_CFG_ENABLE)) |
+		     M_SPC_CFG_ENABLE | M_SPC_CFG_CLEAR | V_SPC_CFG_SRC1(1),
+		     IOADDR(A_SCD_PERF_CNT_CFG));
+
+	/*
+	 * We grab this interrupt to prevent others from trying to use
+	 * it, even though we don't want to service the interrupts
+	 * (they only feed into the trace-on-interrupt mechanism)
+	 */
+	if (request_irq(K_INT_PERF_CNT, sbprof_pc_intr, 0, DEVNAME " scd perfcnt", &sbp)) {
+		free_irq(K_INT_TRACE_FREEZE, &sbp);
+		return -EBUSY;
+	}
+
+	/*
+	 * I need the core to mask these, but the interrupt mapper to
+	 *  pass them through.	I am exploiting my knowledge that
+	 *  cp0_status masks out IP[5]. krw
+	 */
+#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80)
+	__raw_writeq(K_BCM1480_INT_MAP_I3,
+		     IOADDR(A_BCM1480_IMR_REGISTER(0, R_BCM1480_IMR_INTERRUPT_MAP_BASE_L) +
+			    ((K_BCM1480_INT_PERF_CNT & 0x3f) << 3)));
+#else
+	__raw_writeq(K_INT_MAP_I3,
+		     IOADDR(A_IMR_REGISTER(0, R_IMR_INTERRUPT_MAP_BASE) +
+			    (K_INT_PERF_CNT << 3)));
+#endif
+
+	/* Initialize address traps */
+	__raw_writeq(0, IOADDR(A_ADDR_TRAP_UP_0));
+	__raw_writeq(0, IOADDR(A_ADDR_TRAP_UP_1));
+	__raw_writeq(0, IOADDR(A_ADDR_TRAP_UP_2));
+	__raw_writeq(0, IOADDR(A_ADDR_TRAP_UP_3));
+
+	__raw_writeq(0, IOADDR(A_ADDR_TRAP_DOWN_0));
+	__raw_writeq(0, IOADDR(A_ADDR_TRAP_DOWN_1));
+	__raw_writeq(0, IOADDR(A_ADDR_TRAP_DOWN_2));
+	__raw_writeq(0, IOADDR(A_ADDR_TRAP_DOWN_3));
+
+	__raw_writeq(0, IOADDR(A_ADDR_TRAP_CFG_0));
+	__raw_writeq(0, IOADDR(A_ADDR_TRAP_CFG_1));
+	__raw_writeq(0, IOADDR(A_ADDR_TRAP_CFG_2));
+	__raw_writeq(0, IOADDR(A_ADDR_TRAP_CFG_3));
+
+	/* Initialize Trace Event 0-7 */
+	/*				when interrupt	*/
+	__raw_writeq(M_SCD_TREVT_INTERRUPT, IOADDR(A_SCD_TRACE_EVENT_0));
+	__raw_writeq(0, IOADDR(A_SCD_TRACE_EVENT_1));
+	__raw_writeq(0, IOADDR(A_SCD_TRACE_EVENT_2));
+	__raw_writeq(0, IOADDR(A_SCD_TRACE_EVENT_3));
+	__raw_writeq(0, IOADDR(A_SCD_TRACE_EVENT_4));
+	__raw_writeq(0, IOADDR(A_SCD_TRACE_EVENT_5));
+	__raw_writeq(0, IOADDR(A_SCD_TRACE_EVENT_6));
+	__raw_writeq(0, IOADDR(A_SCD_TRACE_EVENT_7));
+
+	/* Initialize Trace Sequence 0-7 */
+	/*				     Start on event 0 (interrupt) */
+	__raw_writeq(V_SCD_TRSEQ_FUNC_START | 0x0fff,
+		     IOADDR(A_SCD_TRACE_SEQUENCE_0));
+	/*			  dsamp when d used | asamp when a used */
+	__raw_writeq(M_SCD_TRSEQ_ASAMPLE | M_SCD_TRSEQ_DSAMPLE |
+		     K_SCD_TRSEQ_TRIGGER_ALL,
+		     IOADDR(A_SCD_TRACE_SEQUENCE_1));
+	__raw_writeq(0, IOADDR(A_SCD_TRACE_SEQUENCE_2));
+	__raw_writeq(0, IOADDR(A_SCD_TRACE_SEQUENCE_3));
+	__raw_writeq(0, IOADDR(A_SCD_TRACE_SEQUENCE_4));
+	__raw_writeq(0, IOADDR(A_SCD_TRACE_SEQUENCE_5));
+	__raw_writeq(0, IOADDR(A_SCD_TRACE_SEQUENCE_6));
+	__raw_writeq(0, IOADDR(A_SCD_TRACE_SEQUENCE_7));
+
+	/* Now indicate the PERF_CNT interrupt as a trace-relevant interrupt */
+#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80)
+	__raw_writeq(1ULL << (K_BCM1480_INT_PERF_CNT & 0x3f),
+		     IOADDR(A_BCM1480_IMR_REGISTER(0, R_BCM1480_IMR_INTERRUPT_TRACE_L)));
+#else
+	__raw_writeq(1ULL << K_INT_PERF_CNT,
+		     IOADDR(A_IMR_REGISTER(0, R_IMR_INTERRUPT_TRACE)));
+#endif
+	arm_tb();
+
+	pr_debug(DEVNAME ": done starting\n");
+
+	return 0;
+}
+
+static int sbprof_zbprof_stop(void)
+{
+	int err = 0;
+
+	pr_debug(DEVNAME ": stopping\n");
+
+	if (sbp.tb_enable) {
+		/*
+		 * XXXKW there is a window here where the intr handler may run,
+		 * see the disable, and do the wake_up before this sleep
+		 * happens.
+		 */
+		pr_debug(DEVNAME ": wait for disarm\n");
+		err = wait_event_interruptible(sbp.tb_sync, !sbp.tb_armed);
+		pr_debug(DEVNAME ": disarm complete, stat %d\n", err);
+
+		if (err)
+			return err;
+
+		sbp.tb_enable = 0;
+		free_irq(K_INT_TRACE_FREEZE, &sbp);
+		free_irq(K_INT_PERF_CNT, &sbp);
+	}
+
+	pr_debug(DEVNAME ": done stopping\n");
+
+	return err;
+}
+
+static int sbprof_tb_open(struct inode *inode, struct file *filp)
+{
+	int minor;
+
+	minor = iminor(inode);
+	if (minor != 0)
+		return -ENODEV;
+
+	if (xchg(&sbp.open, SB_OPENING) != SB_CLOSED)
+		return -EBUSY;
+
+	memset(&sbp, 0, sizeof(struct sbprof_tb));
+	sbp.sbprof_tbbuf = vzalloc(MAX_TBSAMPLE_BYTES);
+	if (!sbp.sbprof_tbbuf) {
+		sbp.open = SB_CLOSED;
+		wmb();
+		return -ENOMEM;
+	}
+
+	init_waitqueue_head(&sbp.tb_sync);
+	init_waitqueue_head(&sbp.tb_read);
+	mutex_init(&sbp.lock);
+
+	sbp.open = SB_OPEN;
+	wmb();
+
+	return 0;
+}
+
+static int sbprof_tb_release(struct inode *inode, struct file *filp)
+{
+	int minor;
+
+	minor = iminor(inode);
+	if (minor != 0 || sbp.open != SB_CLOSED)
+		return -ENODEV;
+
+	mutex_lock(&sbp.lock);
+
+	if (sbp.tb_armed || sbp.tb_enable)
+		sbprof_zbprof_stop();
+
+	vfree(sbp.sbprof_tbbuf);
+	sbp.open = SB_CLOSED;
+	wmb();
+
+	mutex_unlock(&sbp.lock);
+
+	return 0;
+}
+
+static ssize_t sbprof_tb_read(struct file *filp, char __user *buf,
+			      size_t size, loff_t *offp)
+{
+	int cur_sample, sample_off, cur_count, sample_left;
+	char *src;
+	int   count   =	 0;
+	char __user *dest    =	 buf;
+	long  cur_off = *offp;
+
+	if (!access_ok(buf, size))
+		return -EFAULT;
+
+	mutex_lock(&sbp.lock);
+
+	count = 0;
+	cur_sample = cur_off / TB_SAMPLE_SIZE;
+	sample_off = cur_off % TB_SAMPLE_SIZE;
+	sample_left = TB_SAMPLE_SIZE - sample_off;
+
+	while (size && (cur_sample < sbp.next_tb_sample)) {
+		int err;
+
+		cur_count = size < sample_left ? size : sample_left;
+		src = (char *)(((long)sbp.sbprof_tbbuf[cur_sample])+sample_off);
+		err = __copy_to_user(dest, src, cur_count);
+		if (err) {
+			*offp = cur_off + cur_count - err;
+			mutex_unlock(&sbp.lock);
+			return err;
+		}
+		pr_debug(DEVNAME ": read from sample %d, %d bytes\n",
+			 cur_sample, cur_count);
+		size -= cur_count;
+		sample_left -= cur_count;
+		if (!sample_left) {
+			cur_sample++;
+			sample_off = 0;
+			sample_left = TB_SAMPLE_SIZE;
+		} else {
+			sample_off += cur_count;
+		}
+		cur_off += cur_count;
+		dest += cur_count;
+		count += cur_count;
+	}
+	*offp = cur_off;
+	mutex_unlock(&sbp.lock);
+
+	return count;
+}
+
+static long sbprof_tb_ioctl(struct file *filp,
+			    unsigned int command,
+			    unsigned long arg)
+{
+	int err = 0;
+
+	switch (command) {
+	case SBPROF_ZBSTART:
+		mutex_lock(&sbp.lock);
+		err = sbprof_zbprof_start(filp);
+		mutex_unlock(&sbp.lock);
+		break;
+
+	case SBPROF_ZBSTOP:
+		mutex_lock(&sbp.lock);
+		err = sbprof_zbprof_stop();
+		mutex_unlock(&sbp.lock);
+		break;
+
+	case SBPROF_ZBWAITFULL: {
+		err = wait_event_interruptible(sbp.tb_read, TB_FULL);
+		if (err)
+			break;
+
+		err = put_user(TB_FULL, (int __user *) arg);
+		break;
+	}
+
+	default:
+		err = -EINVAL;
+		break;
+	}
+
+	return err;
+}
+
+static const struct file_operations sbprof_tb_fops = {
+	.owner		= THIS_MODULE,
+	.open		= sbprof_tb_open,
+	.release	= sbprof_tb_release,
+	.read		= sbprof_tb_read,
+	.unlocked_ioctl = sbprof_tb_ioctl,
+	.compat_ioctl	= sbprof_tb_ioctl,
+	.mmap		= NULL,
+	.llseek		= default_llseek,
+};
+
+static struct class *tb_class;
+static struct device *tb_dev;
+
+static int __init sbprof_tb_init(void)
+{
+	struct device *dev;
+	struct class *tbc;
+	int err;
+
+	if (register_chrdev(SBPROF_TB_MAJOR, DEVNAME, &sbprof_tb_fops)) {
+		printk(KERN_WARNING DEVNAME ": initialization failed (dev %d)\n",
+		       SBPROF_TB_MAJOR);
+		return -EIO;
+	}
+
+	tbc = class_create(THIS_MODULE, "sb_tracebuffer");
+	if (IS_ERR(tbc)) {
+		err = PTR_ERR(tbc);
+		goto out_chrdev;
+	}
+
+	tb_class = tbc;
+
+	dev = device_create(tbc, NULL, MKDEV(SBPROF_TB_MAJOR, 0), NULL, "tb");
+	if (IS_ERR(dev)) {
+		err = PTR_ERR(dev);
+		goto out_class;
+	}
+	tb_dev = dev;
+
+	sbp.open = SB_CLOSED;
+	wmb();
+	tb_period = zbbus_mhz * 10000LL;
+	pr_info(DEVNAME ": initialized - tb_period = %lld\n",
+		(long long) tb_period);
+	return 0;
+
+out_class:
+	class_destroy(tb_class);
+out_chrdev:
+	unregister_chrdev(SBPROF_TB_MAJOR, DEVNAME);
+
+	return err;
+}
+
+static void __exit sbprof_tb_cleanup(void)
+{
+	device_destroy(tb_class, MKDEV(SBPROF_TB_MAJOR, 0));
+	unregister_chrdev(SBPROF_TB_MAJOR, DEVNAME);
+	class_destroy(tb_class);
+}
+
+module_init(sbprof_tb_init);
+module_exit(sbprof_tb_cleanup);
+
+MODULE_ALIAS_CHARDEV_MAJOR(SBPROF_TB_MAJOR);
+MODULE_AUTHOR("Ralf Baechle <ralf@linux-mips.org>");
+MODULE_LICENSE("GPL");
diff --git a/arch/mips/sibyte/sb1250/Makefile b/arch/mips/sibyte/sb1250/Makefile
new file mode 100644
index 000000000..cf1327d3f
--- /dev/null
+++ b/arch/mips/sibyte/sb1250/Makefile
@@ -0,0 +1,4 @@
+# SPDX-License-Identifier: GPL-2.0-only
+obj-y := setup.o irq.o time.o
+
+obj-$(CONFIG_SMP)			+= smp.o
diff --git a/arch/mips/sibyte/sb1250/irq.c b/arch/mips/sibyte/sb1250/irq.c
new file mode 100644
index 000000000..2f08ad267
--- /dev/null
+++ b/arch/mips/sibyte/sb1250/irq.c
@@ -0,0 +1,318 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2000, 2001, 2002, 2003 Broadcom Corporation
+ */
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/linkage.h>
+#include <linux/interrupt.h>
+#include <linux/spinlock.h>
+#include <linux/smp.h>
+#include <linux/mm.h>
+#include <linux/kernel_stat.h>
+
+#include <asm/errno.h>
+#include <asm/signal.h>
+#include <asm/time.h>
+#include <asm/io.h>
+
+#include <asm/sibyte/sb1250_regs.h>
+#include <asm/sibyte/sb1250_int.h>
+#include <asm/sibyte/sb1250_uart.h>
+#include <asm/sibyte/sb1250_scd.h>
+#include <asm/sibyte/sb1250.h>
+
+/*
+ * These are the routines that handle all the low level interrupt stuff.
+ * Actions handled here are: initialization of the interrupt map, requesting of
+ * interrupt lines by handlers, dispatching if interrupts to handlers, probing
+ * for interrupt lines
+ */
+
+#ifdef CONFIG_SIBYTE_HAS_LDT
+extern unsigned long ldt_eoi_space;
+#endif
+
+/* Store the CPU id (not the logical number) */
+int sb1250_irq_owner[SB1250_NR_IRQS];
+
+static DEFINE_RAW_SPINLOCK(sb1250_imr_lock);
+
+void sb1250_mask_irq(int cpu, int irq)
+{
+	unsigned long flags;
+	u64 cur_ints;
+
+	raw_spin_lock_irqsave(&sb1250_imr_lock, flags);
+	cur_ints = ____raw_readq(IOADDR(A_IMR_MAPPER(cpu) +
+					R_IMR_INTERRUPT_MASK));
+	cur_ints |= (((u64) 1) << irq);
+	____raw_writeq(cur_ints, IOADDR(A_IMR_MAPPER(cpu) +
+					R_IMR_INTERRUPT_MASK));
+	raw_spin_unlock_irqrestore(&sb1250_imr_lock, flags);
+}
+
+void sb1250_unmask_irq(int cpu, int irq)
+{
+	unsigned long flags;
+	u64 cur_ints;
+
+	raw_spin_lock_irqsave(&sb1250_imr_lock, flags);
+	cur_ints = ____raw_readq(IOADDR(A_IMR_MAPPER(cpu) +
+					R_IMR_INTERRUPT_MASK));
+	cur_ints &= ~(((u64) 1) << irq);
+	____raw_writeq(cur_ints, IOADDR(A_IMR_MAPPER(cpu) +
+					R_IMR_INTERRUPT_MASK));
+	raw_spin_unlock_irqrestore(&sb1250_imr_lock, flags);
+}
+
+#ifdef CONFIG_SMP
+static int sb1250_set_affinity(struct irq_data *d, const struct cpumask *mask,
+			       bool force)
+{
+	int i = 0, old_cpu, cpu, int_on;
+	unsigned int irq = d->irq;
+	u64 cur_ints;
+	unsigned long flags;
+
+	i = cpumask_first_and(mask, cpu_online_mask);
+
+	/* Convert logical CPU to physical CPU */
+	cpu = cpu_logical_map(i);
+
+	/* Protect against other affinity changers and IMR manipulation */
+	raw_spin_lock_irqsave(&sb1250_imr_lock, flags);
+
+	/* Swizzle each CPU's IMR (but leave the IP selection alone) */
+	old_cpu = sb1250_irq_owner[irq];
+	cur_ints = ____raw_readq(IOADDR(A_IMR_MAPPER(old_cpu) +
+					R_IMR_INTERRUPT_MASK));
+	int_on = !(cur_ints & (((u64) 1) << irq));
+	if (int_on) {
+		/* If it was on, mask it */
+		cur_ints |= (((u64) 1) << irq);
+		____raw_writeq(cur_ints, IOADDR(A_IMR_MAPPER(old_cpu) +
+					R_IMR_INTERRUPT_MASK));
+	}
+	sb1250_irq_owner[irq] = cpu;
+	if (int_on) {
+		/* unmask for the new CPU */
+		cur_ints = ____raw_readq(IOADDR(A_IMR_MAPPER(cpu) +
+					R_IMR_INTERRUPT_MASK));
+		cur_ints &= ~(((u64) 1) << irq);
+		____raw_writeq(cur_ints, IOADDR(A_IMR_MAPPER(cpu) +
+					R_IMR_INTERRUPT_MASK));
+	}
+	raw_spin_unlock_irqrestore(&sb1250_imr_lock, flags);
+
+	return 0;
+}
+#endif
+
+static void disable_sb1250_irq(struct irq_data *d)
+{
+	unsigned int irq = d->irq;
+
+	sb1250_mask_irq(sb1250_irq_owner[irq], irq);
+}
+
+static void enable_sb1250_irq(struct irq_data *d)
+{
+	unsigned int irq = d->irq;
+
+	sb1250_unmask_irq(sb1250_irq_owner[irq], irq);
+}
+
+
+static void ack_sb1250_irq(struct irq_data *d)
+{
+	unsigned int irq = d->irq;
+#ifdef CONFIG_SIBYTE_HAS_LDT
+	u64 pending;
+
+	/*
+	 * If the interrupt was an HT interrupt, now is the time to
+	 * clear it.  NOTE: we assume the HT bridge was set up to
+	 * deliver the interrupts to all CPUs (which makes affinity
+	 * changing easier for us)
+	 */
+	pending = __raw_readq(IOADDR(A_IMR_REGISTER(sb1250_irq_owner[irq],
+						    R_IMR_LDT_INTERRUPT)));
+	pending &= ((u64)1 << (irq));
+	if (pending) {
+		int i;
+		for (i=0; i<NR_CPUS; i++) {
+			int cpu;
+#ifdef CONFIG_SMP
+			cpu = cpu_logical_map(i);
+#else
+			cpu = i;
+#endif
+			/*
+			 * Clear for all CPUs so an affinity switch
+			 * doesn't find an old status
+			 */
+			__raw_writeq(pending,
+				     IOADDR(A_IMR_REGISTER(cpu,
+						R_IMR_LDT_INTERRUPT_CLR)));
+		}
+
+		/*
+		 * Generate EOI.  For Pass 1 parts, EOI is a nop.  For
+		 * Pass 2, the LDT world may be edge-triggered, but
+		 * this EOI shouldn't hurt.  If they are
+		 * level-sensitive, the EOI is required.
+		 */
+		*(uint32_t *)(ldt_eoi_space+(irq<<16)+(7<<2)) = 0;
+	}
+#endif
+	sb1250_mask_irq(sb1250_irq_owner[irq], irq);
+}
+
+static struct irq_chip sb1250_irq_type = {
+	.name = "SB1250-IMR",
+	.irq_mask_ack = ack_sb1250_irq,
+	.irq_unmask = enable_sb1250_irq,
+	.irq_mask = disable_sb1250_irq,
+#ifdef CONFIG_SMP
+	.irq_set_affinity = sb1250_set_affinity
+#endif
+};
+
+void __init init_sb1250_irqs(void)
+{
+	int i;
+
+	for (i = 0; i < SB1250_NR_IRQS; i++) {
+		irq_set_chip_and_handler(i, &sb1250_irq_type,
+					 handle_level_irq);
+		sb1250_irq_owner[i] = 0;
+	}
+}
+
+
+/*
+ *  arch_init_irq is called early in the boot sequence from init/main.c via
+ *  init_IRQ.  It is responsible for setting up the interrupt mapper and
+ *  installing the handler that will be responsible for dispatching interrupts
+ *  to the "right" place.
+ */
+/*
+ * For now, map all interrupts to IP[2].  We could save
+ * some cycles by parceling out system interrupts to different
+ * IP lines, but keep it simple for bringup.  We'll also direct
+ * all interrupts to a single CPU; we should probably route
+ * PCI and LDT to one cpu and everything else to the other
+ * to balance the load a bit.
+ *
+ * On the second cpu, everything is set to IP5, which is
+ * ignored, EXCEPT the mailbox interrupt.  That one is
+ * set to IP[2] so it is handled.  This is needed so we
+ * can do cross-cpu function calls, as required by SMP
+ */
+
+#define IMR_IP2_VAL	K_INT_MAP_I0
+#define IMR_IP3_VAL	K_INT_MAP_I1
+#define IMR_IP4_VAL	K_INT_MAP_I2
+#define IMR_IP5_VAL	K_INT_MAP_I3
+#define IMR_IP6_VAL	K_INT_MAP_I4
+
+void __init arch_init_irq(void)
+{
+
+	unsigned int i;
+	u64 tmp;
+	unsigned int imask = STATUSF_IP4 | STATUSF_IP3 | STATUSF_IP2 |
+		STATUSF_IP1 | STATUSF_IP0;
+
+	/* Default everything to IP2 */
+	for (i = 0; i < SB1250_NR_IRQS; i++) {	/* was I0 */
+		__raw_writeq(IMR_IP2_VAL,
+			     IOADDR(A_IMR_REGISTER(0,
+						   R_IMR_INTERRUPT_MAP_BASE) +
+				    (i << 3)));
+		__raw_writeq(IMR_IP2_VAL,
+			     IOADDR(A_IMR_REGISTER(1,
+						   R_IMR_INTERRUPT_MAP_BASE) +
+				    (i << 3)));
+	}
+
+	init_sb1250_irqs();
+
+	/*
+	 * Map the high 16 bits of the mailbox registers to IP[3], for
+	 * inter-cpu messages
+	 */
+	/* Was I1 */
+	__raw_writeq(IMR_IP3_VAL,
+		     IOADDR(A_IMR_REGISTER(0, R_IMR_INTERRUPT_MAP_BASE) +
+			    (K_INT_MBOX_0 << 3)));
+	__raw_writeq(IMR_IP3_VAL,
+		     IOADDR(A_IMR_REGISTER(1, R_IMR_INTERRUPT_MAP_BASE) +
+			    (K_INT_MBOX_0 << 3)));
+
+	/* Clear the mailboxes.	 The firmware may leave them dirty */
+	__raw_writeq(0xffffffffffffffffULL,
+		     IOADDR(A_IMR_REGISTER(0, R_IMR_MAILBOX_CLR_CPU)));
+	__raw_writeq(0xffffffffffffffffULL,
+		     IOADDR(A_IMR_REGISTER(1, R_IMR_MAILBOX_CLR_CPU)));
+
+	/* Mask everything except the mailbox registers for both cpus */
+	tmp = ~((u64) 0) ^ (((u64) 1) << K_INT_MBOX_0);
+	__raw_writeq(tmp, IOADDR(A_IMR_REGISTER(0, R_IMR_INTERRUPT_MASK)));
+	__raw_writeq(tmp, IOADDR(A_IMR_REGISTER(1, R_IMR_INTERRUPT_MASK)));
+
+	/* Enable necessary IPs, disable the rest */
+	change_c0_status(ST0_IM, imask);
+}
+
+extern void sb1250_mailbox_interrupt(void);
+
+static inline void dispatch_ip2(void)
+{
+	unsigned int cpu = smp_processor_id();
+	unsigned long long mask;
+
+	/*
+	 * Default...we've hit an IP[2] interrupt, which means we've got to
+	 * check the 1250 interrupt registers to figure out what to do.	 Need
+	 * to detect which CPU we're on, now that smp_affinity is supported.
+	 */
+	mask = __raw_readq(IOADDR(A_IMR_REGISTER(cpu,
+				  R_IMR_INTERRUPT_STATUS_BASE)));
+	if (mask)
+		do_IRQ(fls64(mask) - 1);
+}
+
+asmlinkage void plat_irq_dispatch(void)
+{
+	unsigned int cpu = smp_processor_id();
+	unsigned int pending;
+
+	/*
+	 * What a pain. We have to be really careful saving the upper 32 bits
+	 * of any * register across function calls if we don't want them
+	 * trashed--since were running in -o32, the calling routing never saves
+	 * the full 64 bits of a register across a function call.  Being the
+	 * interrupt handler, we're guaranteed that interrupts are disabled
+	 * during this code so we don't have to worry about random interrupts
+	 * blasting the high 32 bits.
+	 */
+
+	pending = read_c0_cause() & read_c0_status() & ST0_IM;
+
+	if (pending & CAUSEF_IP7) /* CPU performance counter interrupt */
+		do_IRQ(MIPS_CPU_IRQ_BASE + 7);
+	else if (pending & CAUSEF_IP4)
+		do_IRQ(K_INT_TIMER_0 + cpu);	/* sb1250_timer_interrupt() */
+
+#ifdef CONFIG_SMP
+	else if (pending & CAUSEF_IP3)
+		sb1250_mailbox_interrupt();
+#endif
+
+	else if (pending & CAUSEF_IP2)
+		dispatch_ip2();
+	else
+		spurious_interrupt();
+}
diff --git a/arch/mips/sibyte/sb1250/setup.c b/arch/mips/sibyte/sb1250/setup.c
new file mode 100644
index 000000000..644b19038
--- /dev/null
+++ b/arch/mips/sibyte/sb1250/setup.c
@@ -0,0 +1,234 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2000, 2001, 2002, 2003 Broadcom Corporation
+ */
+#include <linux/export.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/reboot.h>
+#include <linux/string.h>
+
+#include <asm/bootinfo.h>
+#include <asm/cpu.h>
+#include <asm/mipsregs.h>
+#include <asm/io.h>
+#include <asm/sibyte/sb1250.h>
+#include <asm/sibyte/sb1250_regs.h>
+#include <asm/sibyte/sb1250_scd.h>
+
+unsigned int sb1_pass;
+unsigned int soc_pass;
+unsigned int soc_type;
+EXPORT_SYMBOL(soc_type);
+unsigned int periph_rev;
+EXPORT_SYMBOL_GPL(periph_rev);
+unsigned int zbbus_mhz;
+EXPORT_SYMBOL(zbbus_mhz);
+
+static char *soc_str;
+static char *pass_str;
+static unsigned int war_pass;	/* XXXKW don't overload PASS defines? */
+
+static int __init setup_bcm1250(void)
+{
+	int ret = 0;
+
+	switch (soc_pass) {
+	case K_SYS_REVISION_BCM1250_PASS1:
+		periph_rev = 1;
+		pass_str = "Pass 1";
+		break;
+	case K_SYS_REVISION_BCM1250_A10:
+		periph_rev = 2;
+		pass_str = "A8/A10";
+		/* XXXKW different war_pass? */
+		war_pass = K_SYS_REVISION_BCM1250_PASS2;
+		break;
+	case K_SYS_REVISION_BCM1250_PASS2_2:
+		periph_rev = 2;
+		pass_str = "B1";
+		break;
+	case K_SYS_REVISION_BCM1250_B2:
+		periph_rev = 2;
+		pass_str = "B2";
+		war_pass = K_SYS_REVISION_BCM1250_PASS2_2;
+		break;
+	case K_SYS_REVISION_BCM1250_PASS3:
+		periph_rev = 3;
+		pass_str = "C0";
+		break;
+	case K_SYS_REVISION_BCM1250_C1:
+		periph_rev = 3;
+		pass_str = "C1";
+		break;
+	default:
+		if (soc_pass < K_SYS_REVISION_BCM1250_PASS2_2) {
+			periph_rev = 2;
+			pass_str = "A0-A6";
+			war_pass = K_SYS_REVISION_BCM1250_PASS2;
+		} else {
+			printk("Unknown BCM1250 rev %x\n", soc_pass);
+			ret = 1;
+		}
+		break;
+	}
+
+	return ret;
+}
+
+int sb1250_m3_workaround_needed(void)
+{
+	switch (soc_type) {
+	case K_SYS_SOC_TYPE_BCM1250:
+	case K_SYS_SOC_TYPE_BCM1250_ALT:
+	case K_SYS_SOC_TYPE_BCM1250_ALT2:
+	case K_SYS_SOC_TYPE_BCM1125:
+	case K_SYS_SOC_TYPE_BCM1125H:
+		return soc_pass < K_SYS_REVISION_BCM1250_C0;
+
+	default:
+		return 0;
+	}
+}
+
+static int __init setup_bcm112x(void)
+{
+	int ret = 0;
+
+	switch (soc_pass) {
+	case 0:
+		/* Early build didn't have revid set */
+		periph_rev = 3;
+		pass_str = "A1";
+		war_pass = K_SYS_REVISION_BCM112x_A1;
+		break;
+	case K_SYS_REVISION_BCM112x_A1:
+		periph_rev = 3;
+		pass_str = "A1";
+		break;
+	case K_SYS_REVISION_BCM112x_A2:
+		periph_rev = 3;
+		pass_str = "A2";
+		break;
+	case K_SYS_REVISION_BCM112x_A3:
+		periph_rev = 3;
+		pass_str = "A3";
+		break;
+	case K_SYS_REVISION_BCM112x_A4:
+		periph_rev = 3;
+		pass_str = "A4";
+		break;
+	case K_SYS_REVISION_BCM112x_B0:
+		periph_rev = 3;
+		pass_str = "B0";
+		break;
+	default:
+		printk("Unknown %s rev %x\n", soc_str, soc_pass);
+		ret = 1;
+	}
+
+	return ret;
+}
+
+/* Setup code likely to be common to all SiByte platforms */
+
+static int __init sys_rev_decode(void)
+{
+	int ret = 0;
+
+	war_pass = soc_pass;
+	switch (soc_type) {
+	case K_SYS_SOC_TYPE_BCM1250:
+	case K_SYS_SOC_TYPE_BCM1250_ALT:
+	case K_SYS_SOC_TYPE_BCM1250_ALT2:
+		soc_str = "BCM1250";
+		ret = setup_bcm1250();
+		break;
+	case K_SYS_SOC_TYPE_BCM1120:
+		soc_str = "BCM1120";
+		ret = setup_bcm112x();
+		break;
+	case K_SYS_SOC_TYPE_BCM1125:
+		soc_str = "BCM1125";
+		ret = setup_bcm112x();
+		break;
+	case K_SYS_SOC_TYPE_BCM1125H:
+		soc_str = "BCM1125H";
+		ret = setup_bcm112x();
+		break;
+	default:
+		printk("Unknown SOC type %x\n", soc_type);
+		ret = 1;
+		break;
+	}
+
+	return ret;
+}
+
+void __init sb1250_setup(void)
+{
+	uint64_t sys_rev;
+	int plldiv;
+	int bad_config = 0;
+
+	sb1_pass = read_c0_prid() & PRID_REV_MASK;
+	sys_rev = __raw_readq(IOADDR(A_SCD_SYSTEM_REVISION));
+	soc_type = SYS_SOC_TYPE(sys_rev);
+	soc_pass = G_SYS_REVISION(sys_rev);
+
+	if (sys_rev_decode()) {
+		printk("Restart after failure to identify SiByte chip\n");
+		machine_restart(NULL);
+	}
+
+	plldiv = G_SYS_PLL_DIV(__raw_readq(IOADDR(A_SCD_SYSTEM_CFG)));
+	zbbus_mhz = ((plldiv >> 1) * 50) + ((plldiv & 1) * 25);
+
+	printk("Broadcom SiByte %s %s @ %d MHz (SB1 rev %d)\n",
+		    soc_str, pass_str, zbbus_mhz * 2, sb1_pass);
+	printk("Board type: %s\n", get_system_type());
+
+	switch (war_pass) {
+	case K_SYS_REVISION_BCM1250_PASS1:
+		printk("@@@@ This is a BCM1250 A0-A2 (Pass 1) board, "
+			    "and the kernel doesn't have the proper "
+			    "workarounds compiled in. @@@@\n");
+		bad_config = 1;
+		break;
+	case K_SYS_REVISION_BCM1250_PASS2:
+		/* Pass 2 - easiest as default for now - so many numbers */
+#if !defined(CONFIG_SB1_PASS_2_WORKAROUNDS) || \
+    !defined(CONFIG_SB1_PASS_2_1_WORKAROUNDS)
+		printk("@@@@ This is a BCM1250 A3-A10 board, and the "
+			    "kernel doesn't have the proper workarounds "
+			    "compiled in. @@@@\n");
+		bad_config = 1;
+#endif
+#ifdef CONFIG_CPU_HAS_PREFETCH
+		printk("@@@@ Prefetches may be enabled in this kernel, "
+			    "but are buggy on this board.  @@@@\n");
+		bad_config = 1;
+#endif
+		break;
+	case K_SYS_REVISION_BCM1250_PASS2_2:
+#ifndef CONFIG_SB1_PASS_2_WORKAROUNDS
+		printk("@@@@ This is a BCM1250 B1/B2. board, and the "
+			    "kernel doesn't have the proper workarounds "
+			    "compiled in. @@@@\n");
+		bad_config = 1;
+#endif
+#if defined(CONFIG_SB1_PASS_2_1_WORKAROUNDS) || \
+    !defined(CONFIG_CPU_HAS_PREFETCH)
+		printk("@@@@ This is a BCM1250 B1/B2, but the kernel is "
+			    "conservatively configured for an 'A' stepping. "
+			    "@@@@\n");
+#endif
+		break;
+	default:
+		break;
+	}
+	if (bad_config) {
+		printk("Invalid configuration for this chip.\n");
+		machine_restart(NULL);
+	}
+}
diff --git a/arch/mips/sibyte/sb1250/smp.c b/arch/mips/sibyte/sb1250/smp.c
new file mode 100644
index 000000000..7a794234e
--- /dev/null
+++ b/arch/mips/sibyte/sb1250/smp.c
@@ -0,0 +1,168 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2001, 2002, 2003 Broadcom Corporation
+ */
+
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/smp.h>
+#include <linux/kernel_stat.h>
+#include <linux/sched/task_stack.h>
+
+#include <asm/mmu_context.h>
+#include <asm/io.h>
+#include <asm/fw/cfe/cfe_api.h>
+#include <asm/sibyte/sb1250.h>
+#include <asm/sibyte/sb1250_regs.h>
+#include <asm/sibyte/sb1250_int.h>
+
+static void *mailbox_set_regs[] = {
+	IOADDR(A_IMR_CPU0_BASE + R_IMR_MAILBOX_SET_CPU),
+	IOADDR(A_IMR_CPU1_BASE + R_IMR_MAILBOX_SET_CPU)
+};
+
+static void *mailbox_clear_regs[] = {
+	IOADDR(A_IMR_CPU0_BASE + R_IMR_MAILBOX_CLR_CPU),
+	IOADDR(A_IMR_CPU1_BASE + R_IMR_MAILBOX_CLR_CPU)
+};
+
+static void *mailbox_regs[] = {
+	IOADDR(A_IMR_CPU0_BASE + R_IMR_MAILBOX_CPU),
+	IOADDR(A_IMR_CPU1_BASE + R_IMR_MAILBOX_CPU)
+};
+
+/*
+ * SMP init and finish on secondary CPUs
+ */
+void sb1250_smp_init(void)
+{
+	unsigned int imask = STATUSF_IP4 | STATUSF_IP3 | STATUSF_IP2 |
+		STATUSF_IP1 | STATUSF_IP0;
+
+	/* Set interrupt mask, but don't enable */
+	change_c0_status(ST0_IM, imask);
+}
+
+/*
+ * These are routines for dealing with the sb1250 smp capabilities
+ * independent of board/firmware
+ */
+
+/*
+ * Simple enough; everything is set up, so just poke the appropriate mailbox
+ * register, and we should be set
+ */
+static void sb1250_send_ipi_single(int cpu, unsigned int action)
+{
+	__raw_writeq((((u64)action) << 48), mailbox_set_regs[cpu]);
+}
+
+static inline void sb1250_send_ipi_mask(const struct cpumask *mask,
+					unsigned int action)
+{
+	unsigned int i;
+
+	for_each_cpu(i, mask)
+		sb1250_send_ipi_single(i, action);
+}
+
+/*
+ * Code to run on secondary just after probing the CPU
+ */
+static void sb1250_init_secondary(void)
+{
+	extern void sb1250_smp_init(void);
+
+	sb1250_smp_init();
+}
+
+/*
+ * Do any tidying up before marking online and running the idle
+ * loop
+ */
+static void sb1250_smp_finish(void)
+{
+	extern void sb1250_clockevent_init(void);
+
+	sb1250_clockevent_init();
+	local_irq_enable();
+}
+
+/*
+ * Setup the PC, SP, and GP of a secondary processor and start it
+ * running!
+ */
+static int sb1250_boot_secondary(int cpu, struct task_struct *idle)
+{
+	int retval;
+
+	retval = cfe_cpu_start(cpu_logical_map(cpu), &smp_bootstrap,
+			       __KSTK_TOS(idle),
+			       (unsigned long)task_thread_info(idle), 0);
+	if (retval != 0)
+		printk("cfe_start_cpu(%i) returned %i\n" , cpu, retval);
+	return retval;
+}
+
+/*
+ * Use CFE to find out how many CPUs are available, setting up
+ * cpu_possible_mask and the logical/physical mappings.
+ * XXXKW will the boot CPU ever not be physical 0?
+ *
+ * Common setup before any secondaries are started
+ */
+static void __init sb1250_smp_setup(void)
+{
+	int i, num;
+
+	init_cpu_possible(cpumask_of(0));
+	__cpu_number_map[0] = 0;
+	__cpu_logical_map[0] = 0;
+
+	for (i = 1, num = 0; i < NR_CPUS; i++) {
+		if (cfe_cpu_stop(i) == 0) {
+			set_cpu_possible(i, true);
+			__cpu_number_map[i] = ++num;
+			__cpu_logical_map[num] = i;
+		}
+	}
+	printk(KERN_INFO "Detected %i available secondary CPU(s)\n", num);
+}
+
+static void __init sb1250_prepare_cpus(unsigned int max_cpus)
+{
+}
+
+const struct plat_smp_ops sb_smp_ops = {
+	.send_ipi_single	= sb1250_send_ipi_single,
+	.send_ipi_mask		= sb1250_send_ipi_mask,
+	.init_secondary		= sb1250_init_secondary,
+	.smp_finish		= sb1250_smp_finish,
+	.boot_secondary		= sb1250_boot_secondary,
+	.smp_setup		= sb1250_smp_setup,
+	.prepare_cpus		= sb1250_prepare_cpus,
+};
+
+void sb1250_mailbox_interrupt(void)
+{
+	int cpu = smp_processor_id();
+	int irq = K_INT_MBOX_0;
+	unsigned int action;
+
+	kstat_incr_irq_this_cpu(irq);
+	/* Load the mailbox register to figure out what we're supposed to do */
+	action = (____raw_readq(mailbox_regs[cpu]) >> 48) & 0xffff;
+
+	/* Clear the mailbox to clear the interrupt */
+	____raw_writeq(((u64)action) << 48, mailbox_clear_regs[cpu]);
+
+	if (action & SMP_RESCHEDULE_YOURSELF)
+		scheduler_ipi();
+
+	if (action & SMP_CALL_FUNCTION) {
+		irq_enter();
+		generic_smp_call_function_interrupt();
+		irq_exit();
+	}
+}
diff --git a/arch/mips/sibyte/sb1250/time.c b/arch/mips/sibyte/sb1250/time.c
new file mode 100644
index 000000000..8b63000a4
--- /dev/null
+++ b/arch/mips/sibyte/sb1250/time.c
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2000, 2001 Broadcom Corporation
+ */
+#include <linux/init.h>
+
+extern void sb1250_clocksource_init(void);
+extern void sb1250_clockevent_init(void);
+
+void __init plat_time_init(void)
+{
+	sb1250_clocksource_init();
+	sb1250_clockevent_init();
+}
diff --git a/arch/mips/sibyte/swarm/Makefile b/arch/mips/sibyte/swarm/Makefile
new file mode 100644
index 000000000..96b41a28f
--- /dev/null
+++ b/arch/mips/sibyte/swarm/Makefile
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0-only
+obj-y				:= platform.o setup.o rtc_xicor1241.o \
+				   rtc_m41t81.o
+
+obj-$(CONFIG_I2C_BOARDINFO)	+= swarm-i2c.o
diff --git a/arch/mips/sibyte/swarm/platform.c b/arch/mips/sibyte/swarm/platform.c
new file mode 100644
index 000000000..484969db7
--- /dev/null
+++ b/arch/mips/sibyte/swarm/platform.c
@@ -0,0 +1,140 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/err.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/platform_device.h>
+#include <linux/ata_platform.h>
+
+#include <asm/sibyte/board.h>
+#include <asm/sibyte/sb1250_genbus.h>
+#include <asm/sibyte/sb1250_regs.h>
+
+#if defined(CONFIG_SIBYTE_SWARM) || defined(CONFIG_SIBYTE_LITTLESUR)
+
+#define DRV_NAME	"pata-swarm"
+
+#define SWARM_IDE_SHIFT 5
+#define SWARM_IDE_BASE	0x1f0
+#define SWARM_IDE_CTRL	0x3f6
+
+static struct resource swarm_pata_resource[] = {
+	{
+		.name	= "Swarm GenBus IDE",
+		.flags	= IORESOURCE_MEM,
+	}, {
+		.name	= "Swarm GenBus IDE",
+		.flags	= IORESOURCE_MEM,
+	}, {
+		.name	= "Swarm GenBus IDE",
+		.flags	= IORESOURCE_IRQ,
+		.start	= K_INT_GB_IDE,
+		.end	= K_INT_GB_IDE,
+	},
+};
+
+static struct pata_platform_info pata_platform_data = {
+	.ioport_shift	= SWARM_IDE_SHIFT,
+};
+
+static struct platform_device swarm_pata_device = {
+	.name		= "pata_platform",
+	.id		= -1,
+	.resource	= swarm_pata_resource,
+	.num_resources	= ARRAY_SIZE(swarm_pata_resource),
+	.dev  = {
+		.platform_data		= &pata_platform_data,
+		.coherent_dma_mask	= ~0,	/* grumble */
+	},
+};
+
+static int __init swarm_pata_init(void)
+{
+	u8 __iomem *base;
+	phys_addr_t offset, size;
+	struct resource *r;
+
+	if (!SIBYTE_HAVE_IDE)
+		return -ENODEV;
+
+	base = ioremap(A_IO_EXT_BASE, 0x800);
+	offset = __raw_readq(base + R_IO_EXT_REG(R_IO_EXT_START_ADDR, IDE_CS));
+	size = __raw_readq(base + R_IO_EXT_REG(R_IO_EXT_MULT_SIZE, IDE_CS));
+	iounmap(base);
+
+	offset = G_IO_START_ADDR(offset) << S_IO_ADDRBASE;
+	size = (G_IO_MULT_SIZE(size) + 1) << S_IO_REGSIZE;
+	if (offset < A_PHYS_GENBUS || offset >= A_PHYS_GENBUS_END) {
+		pr_info(DRV_NAME ": PATA interface at GenBus disabled\n");
+
+		return -EBUSY;
+	}
+
+	pr_info(DRV_NAME ": PATA interface at GenBus slot %i\n", IDE_CS);
+
+	r = swarm_pata_resource;
+	r[0].start = offset + (SWARM_IDE_BASE << SWARM_IDE_SHIFT);
+	r[0].end   = offset + ((SWARM_IDE_BASE + 8) << SWARM_IDE_SHIFT) - 1;
+	r[1].start = offset + (SWARM_IDE_CTRL << SWARM_IDE_SHIFT);
+	r[1].end   = offset + ((SWARM_IDE_CTRL + 1) << SWARM_IDE_SHIFT) - 1;
+
+	return platform_device_register(&swarm_pata_device);
+}
+
+device_initcall(swarm_pata_init);
+
+#endif /* defined(CONFIG_SIBYTE_SWARM) || defined(CONFIG_SIBYTE_LITTLESUR) */
+
+#define sb1250_dev_struct(num) \
+	static struct resource sb1250_res##num = {		\
+		.name = "SB1250 MAC " __stringify(num),		\
+		.flags = IORESOURCE_MEM,		\
+		.start = A_MAC_CHANNEL_BASE(num),	\
+		.end = A_MAC_CHANNEL_BASE(num + 1) -1,	\
+	};\
+	static struct platform_device sb1250_dev##num = {	\
+		.name = "sb1250-mac",			\
+	.id = num,					\
+	.resource = &sb1250_res##num,			\
+	.num_resources = 1,				\
+	}
+
+sb1250_dev_struct(0);
+sb1250_dev_struct(1);
+sb1250_dev_struct(2);
+sb1250_dev_struct(3);
+
+static struct platform_device *sb1250_devs[] __initdata = {
+	&sb1250_dev0,
+	&sb1250_dev1,
+	&sb1250_dev2,
+	&sb1250_dev3,
+};
+
+static int __init sb1250_device_init(void)
+{
+	int ret;
+
+	/* Set the number of available units based on the SOC type.  */
+	switch (soc_type) {
+	case K_SYS_SOC_TYPE_BCM1250:
+	case K_SYS_SOC_TYPE_BCM1250_ALT:
+		ret = platform_add_devices(sb1250_devs, 3);
+		break;
+	case K_SYS_SOC_TYPE_BCM1120:
+	case K_SYS_SOC_TYPE_BCM1125:
+	case K_SYS_SOC_TYPE_BCM1125H:
+	case K_SYS_SOC_TYPE_BCM1250_ALT2:	/* Hybrid */
+		ret = platform_add_devices(sb1250_devs, 2);
+		break;
+	case K_SYS_SOC_TYPE_BCM1x55:
+	case K_SYS_SOC_TYPE_BCM1x80:
+		ret = platform_add_devices(sb1250_devs, 4);
+		break;
+	default:
+		ret = -ENODEV;
+		break;
+	}
+	return ret;
+}
+device_initcall(sb1250_device_init);
diff --git a/arch/mips/sibyte/swarm/rtc_m41t81.c b/arch/mips/sibyte/swarm/rtc_m41t81.c
new file mode 100644
index 000000000..afe1e3460
--- /dev/null
+++ b/arch/mips/sibyte/swarm/rtc_m41t81.c
@@ -0,0 +1,228 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2000, 2001 Broadcom Corporation
+ *
+ * Copyright (C) 2002 MontaVista Software Inc.
+ * Author: jsun@mvista.com or jsun@junsun.net
+ */
+#include <linux/bcd.h>
+#include <linux/types.h>
+#include <linux/time.h>
+
+#include <asm/time.h>
+#include <asm/addrspace.h>
+#include <asm/io.h>
+
+#include <asm/sibyte/sb1250.h>
+#include <asm/sibyte/sb1250_regs.h>
+#include <asm/sibyte/sb1250_smbus.h>
+
+
+/* M41T81 definitions */
+
+/*
+ * Register bits
+ */
+
+#define M41T81REG_SC_ST		0x80		/* stop bit */
+#define M41T81REG_HR_CB		0x40		/* century bit */
+#define M41T81REG_HR_CEB	0x80		/* century enable bit */
+#define M41T81REG_CTL_S		0x20		/* sign bit */
+#define M41T81REG_CTL_FT	0x40		/* frequency test bit */
+#define M41T81REG_CTL_OUT	0x80		/* output level */
+#define M41T81REG_WD_RB0	0x01		/* watchdog resolution bit 0 */
+#define M41T81REG_WD_RB1	0x02		/* watchdog resolution bit 1 */
+#define M41T81REG_WD_BMB0	0x04		/* watchdog multiplier bit 0 */
+#define M41T81REG_WD_BMB1	0x08		/* watchdog multiplier bit 1 */
+#define M41T81REG_WD_BMB2	0x10		/* watchdog multiplier bit 2 */
+#define M41T81REG_WD_BMB3	0x20		/* watchdog multiplier bit 3 */
+#define M41T81REG_WD_BMB4	0x40		/* watchdog multiplier bit 4 */
+#define M41T81REG_AMO_ABE	0x20		/* alarm in "battery back-up mode" enable bit */
+#define M41T81REG_AMO_SQWE	0x40		/* square wave enable */
+#define M41T81REG_AMO_AFE	0x80		/* alarm flag enable flag */
+#define M41T81REG_ADT_RPT5	0x40		/* alarm repeat mode bit 5 */
+#define M41T81REG_ADT_RPT4	0x80		/* alarm repeat mode bit 4 */
+#define M41T81REG_AHR_RPT3	0x80		/* alarm repeat mode bit 3 */
+#define M41T81REG_AHR_HT	0x40		/* halt update bit */
+#define M41T81REG_AMN_RPT2	0x80		/* alarm repeat mode bit 2 */
+#define M41T81REG_ASC_RPT1	0x80		/* alarm repeat mode bit 1 */
+#define M41T81REG_FLG_AF	0x40		/* alarm flag (read only) */
+#define M41T81REG_FLG_WDF	0x80		/* watchdog flag (read only) */
+#define M41T81REG_SQW_RS0	0x10		/* sqw frequency bit 0 */
+#define M41T81REG_SQW_RS1	0x20		/* sqw frequency bit 1 */
+#define M41T81REG_SQW_RS2	0x40		/* sqw frequency bit 2 */
+#define M41T81REG_SQW_RS3	0x80		/* sqw frequency bit 3 */
+
+
+/*
+ * Register numbers
+ */
+
+#define M41T81REG_TSC	0x00		/* tenths/hundredths of second */
+#define M41T81REG_SC	0x01		/* seconds */
+#define M41T81REG_MN	0x02		/* minute */
+#define M41T81REG_HR	0x03		/* hour/century */
+#define M41T81REG_DY	0x04		/* day of week */
+#define M41T81REG_DT	0x05		/* date of month */
+#define M41T81REG_MO	0x06		/* month */
+#define M41T81REG_YR	0x07		/* year */
+#define M41T81REG_CTL	0x08		/* control */
+#define M41T81REG_WD	0x09		/* watchdog */
+#define M41T81REG_AMO	0x0A		/* alarm: month */
+#define M41T81REG_ADT	0x0B		/* alarm: date */
+#define M41T81REG_AHR	0x0C		/* alarm: hour */
+#define M41T81REG_AMN	0x0D		/* alarm: minute */
+#define M41T81REG_ASC	0x0E		/* alarm: second */
+#define M41T81REG_FLG	0x0F		/* flags */
+#define M41T81REG_SQW	0x13		/* square wave register */
+
+#define M41T81_CCR_ADDRESS	0x68
+
+#define SMB_CSR(reg)	IOADDR(A_SMB_REGISTER(1, reg))
+
+static int m41t81_read(uint8_t addr)
+{
+	while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY)
+		;
+
+	__raw_writeq(addr & 0xff, SMB_CSR(R_SMB_CMD));
+	__raw_writeq(V_SMB_ADDR(M41T81_CCR_ADDRESS) | V_SMB_TT_WR1BYTE,
+		     SMB_CSR(R_SMB_START));
+
+	while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY)
+		;
+
+	__raw_writeq(V_SMB_ADDR(M41T81_CCR_ADDRESS) | V_SMB_TT_RD1BYTE,
+		     SMB_CSR(R_SMB_START));
+
+	while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY)
+		;
+
+	if (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_ERROR) {
+		/* Clear error bit by writing a 1 */
+		__raw_writeq(M_SMB_ERROR, SMB_CSR(R_SMB_STATUS));
+		return -1;
+	}
+
+	return __raw_readq(SMB_CSR(R_SMB_DATA)) & 0xff;
+}
+
+static int m41t81_write(uint8_t addr, int b)
+{
+	while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY)
+		;
+
+	__raw_writeq(addr & 0xff, SMB_CSR(R_SMB_CMD));
+	__raw_writeq(b & 0xff, SMB_CSR(R_SMB_DATA));
+	__raw_writeq(V_SMB_ADDR(M41T81_CCR_ADDRESS) | V_SMB_TT_WR2BYTE,
+		     SMB_CSR(R_SMB_START));
+
+	while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY)
+		;
+
+	if (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_ERROR) {
+		/* Clear error bit by writing a 1 */
+		__raw_writeq(M_SMB_ERROR, SMB_CSR(R_SMB_STATUS));
+		return -1;
+	}
+
+	/* read the same byte again to make sure it is written */
+	__raw_writeq(V_SMB_ADDR(M41T81_CCR_ADDRESS) | V_SMB_TT_RD1BYTE,
+		     SMB_CSR(R_SMB_START));
+
+	while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY)
+		;
+
+	return 0;
+}
+
+int m41t81_set_time(time64_t t)
+{
+	struct rtc_time tm;
+	unsigned long flags;
+
+	/* Note we don't care about the century */
+	rtc_time64_to_tm(t, &tm);
+
+	/*
+	 * Note the write order matters as it ensures the correctness.
+	 * When we write sec, 10th sec is clear.  It is reasonable to
+	 * believe we should finish writing min within a second.
+	 */
+
+	spin_lock_irqsave(&rtc_lock, flags);
+	tm.tm_sec = bin2bcd(tm.tm_sec);
+	m41t81_write(M41T81REG_SC, tm.tm_sec);
+
+	tm.tm_min = bin2bcd(tm.tm_min);
+	m41t81_write(M41T81REG_MN, tm.tm_min);
+
+	tm.tm_hour = bin2bcd(tm.tm_hour);
+	tm.tm_hour = (tm.tm_hour & 0x3f) | (m41t81_read(M41T81REG_HR) & 0xc0);
+	m41t81_write(M41T81REG_HR, tm.tm_hour);
+
+	/* tm_wday starts from 0 to 6 */
+	if (tm.tm_wday == 0) tm.tm_wday = 7;
+	tm.tm_wday = bin2bcd(tm.tm_wday);
+	m41t81_write(M41T81REG_DY, tm.tm_wday);
+
+	tm.tm_mday = bin2bcd(tm.tm_mday);
+	m41t81_write(M41T81REG_DT, tm.tm_mday);
+
+	/* tm_mon starts from 0, *ick* */
+	tm.tm_mon ++;
+	tm.tm_mon = bin2bcd(tm.tm_mon);
+	m41t81_write(M41T81REG_MO, tm.tm_mon);
+
+	/* we don't do century, everything is beyond 2000 */
+	tm.tm_year %= 100;
+	tm.tm_year = bin2bcd(tm.tm_year);
+	m41t81_write(M41T81REG_YR, tm.tm_year);
+	spin_unlock_irqrestore(&rtc_lock, flags);
+
+	return 0;
+}
+
+time64_t m41t81_get_time(void)
+{
+	unsigned int year, mon, day, hour, min, sec;
+	unsigned long flags;
+
+	/*
+	 * min is valid if two reads of sec are the same.
+	 */
+	for (;;) {
+		spin_lock_irqsave(&rtc_lock, flags);
+		sec = m41t81_read(M41T81REG_SC);
+		min = m41t81_read(M41T81REG_MN);
+		if (sec == m41t81_read(M41T81REG_SC)) break;
+		spin_unlock_irqrestore(&rtc_lock, flags);
+	}
+	hour = m41t81_read(M41T81REG_HR) & 0x3f;
+	day = m41t81_read(M41T81REG_DT);
+	mon = m41t81_read(M41T81REG_MO);
+	year = m41t81_read(M41T81REG_YR);
+	spin_unlock_irqrestore(&rtc_lock, flags);
+
+	sec = bcd2bin(sec);
+	min = bcd2bin(min);
+	hour = bcd2bin(hour);
+	day = bcd2bin(day);
+	mon = bcd2bin(mon);
+	year = bcd2bin(year);
+
+	year += 2000;
+
+	return mktime64(year, mon, day, hour, min, sec);
+}
+
+int m41t81_probe(void)
+{
+	unsigned int tmp;
+
+	/* enable chip if it is not enabled yet */
+	tmp = m41t81_read(M41T81REG_SC);
+	m41t81_write(M41T81REG_SC, tmp & 0x7f);
+
+	return m41t81_read(M41T81REG_SC) != -1;
+}
diff --git a/arch/mips/sibyte/swarm/rtc_xicor1241.c b/arch/mips/sibyte/swarm/rtc_xicor1241.c
new file mode 100644
index 000000000..e2164200c
--- /dev/null
+++ b/arch/mips/sibyte/swarm/rtc_xicor1241.c
@@ -0,0 +1,206 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2000, 2001 Broadcom Corporation
+ *
+ * Copyright (C) 2002 MontaVista Software Inc.
+ * Author: jsun@mvista.com or jsun@junsun.net
+ */
+#include <linux/bcd.h>
+#include <linux/types.h>
+#include <linux/time.h>
+
+#include <asm/time.h>
+#include <asm/addrspace.h>
+#include <asm/io.h>
+
+#include <asm/sibyte/sb1250.h>
+#include <asm/sibyte/sb1250_regs.h>
+#include <asm/sibyte/sb1250_smbus.h>
+
+
+/* Xicor 1241 definitions */
+
+/*
+ * Register bits
+ */
+
+#define X1241REG_SR_BAT 0x80		/* currently on battery power */
+#define X1241REG_SR_RWEL 0x04		/* r/w latch is enabled, can write RTC */
+#define X1241REG_SR_WEL 0x02		/* r/w latch is unlocked, can enable r/w now */
+#define X1241REG_SR_RTCF 0x01		/* clock failed */
+#define X1241REG_BL_BP2 0x80		/* block protect 2 */
+#define X1241REG_BL_BP1 0x40		/* block protect 1 */
+#define X1241REG_BL_BP0 0x20		/* block protect 0 */
+#define X1241REG_BL_WD1 0x10
+#define X1241REG_BL_WD0 0x08
+#define X1241REG_HR_MIL 0x80		/* military time format */
+
+/*
+ * Register numbers
+ */
+
+#define X1241REG_BL	0x10		/* block protect bits */
+#define X1241REG_INT	0x11		/*  */
+#define X1241REG_SC	0x30		/* Seconds */
+#define X1241REG_MN	0x31		/* Minutes */
+#define X1241REG_HR	0x32		/* Hours */
+#define X1241REG_DT	0x33		/* Day of month */
+#define X1241REG_MO	0x34		/* Month */
+#define X1241REG_YR	0x35		/* Year */
+#define X1241REG_DW	0x36		/* Day of Week */
+#define X1241REG_Y2K	0x37		/* Year 2K */
+#define X1241REG_SR	0x3F		/* Status register */
+
+#define X1241_CCR_ADDRESS	0x6F
+
+#define SMB_CSR(reg)	IOADDR(A_SMB_REGISTER(1, reg))
+
+static int xicor_read(uint8_t addr)
+{
+	while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY)
+		;
+
+	__raw_writeq((addr >> 8) & 0x7, SMB_CSR(R_SMB_CMD));
+	__raw_writeq(addr & 0xff, SMB_CSR(R_SMB_DATA));
+	__raw_writeq(V_SMB_ADDR(X1241_CCR_ADDRESS) | V_SMB_TT_WR2BYTE,
+		     SMB_CSR(R_SMB_START));
+
+	while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY)
+		;
+
+	__raw_writeq(V_SMB_ADDR(X1241_CCR_ADDRESS) | V_SMB_TT_RD1BYTE,
+		     SMB_CSR(R_SMB_START));
+
+	while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY)
+		;
+
+	if (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_ERROR) {
+		/* Clear error bit by writing a 1 */
+		__raw_writeq(M_SMB_ERROR, SMB_CSR(R_SMB_STATUS));
+		return -1;
+	}
+
+	return __raw_readq(SMB_CSR(R_SMB_DATA)) & 0xff;
+}
+
+static int xicor_write(uint8_t addr, int b)
+{
+	while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY)
+		;
+
+	__raw_writeq(addr, SMB_CSR(R_SMB_CMD));
+	__raw_writeq((addr & 0xff) | ((b & 0xff) << 8), SMB_CSR(R_SMB_DATA));
+	__raw_writeq(V_SMB_ADDR(X1241_CCR_ADDRESS) | V_SMB_TT_WR3BYTE,
+		     SMB_CSR(R_SMB_START));
+
+	while (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_BUSY)
+		;
+
+	if (__raw_readq(SMB_CSR(R_SMB_STATUS)) & M_SMB_ERROR) {
+		/* Clear error bit by writing a 1 */
+		__raw_writeq(M_SMB_ERROR, SMB_CSR(R_SMB_STATUS));
+		return -1;
+	} else {
+		return 0;
+	}
+}
+
+int xicor_set_time(time64_t t)
+{
+	struct rtc_time tm;
+	int tmp;
+	unsigned long flags;
+
+	rtc_time64_to_tm(t, &tm);
+	tm.tm_year += 1900;
+
+	spin_lock_irqsave(&rtc_lock, flags);
+	/* unlock writes to the CCR */
+	xicor_write(X1241REG_SR, X1241REG_SR_WEL);
+	xicor_write(X1241REG_SR, X1241REG_SR_WEL | X1241REG_SR_RWEL);
+
+	/* trivial ones */
+	tm.tm_sec = bin2bcd(tm.tm_sec);
+	xicor_write(X1241REG_SC, tm.tm_sec);
+
+	tm.tm_min = bin2bcd(tm.tm_min);
+	xicor_write(X1241REG_MN, tm.tm_min);
+
+	tm.tm_mday = bin2bcd(tm.tm_mday);
+	xicor_write(X1241REG_DT, tm.tm_mday);
+
+	/* tm_mon starts from 0, *ick* */
+	tm.tm_mon ++;
+	tm.tm_mon = bin2bcd(tm.tm_mon);
+	xicor_write(X1241REG_MO, tm.tm_mon);
+
+	/* year is split */
+	tmp = tm.tm_year / 100;
+	tm.tm_year %= 100;
+	xicor_write(X1241REG_YR, tm.tm_year);
+	xicor_write(X1241REG_Y2K, tmp);
+
+	/* hour is the most tricky one */
+	tmp = xicor_read(X1241REG_HR);
+	if (tmp & X1241REG_HR_MIL) {
+		/* 24 hour format */
+		tm.tm_hour = bin2bcd(tm.tm_hour);
+		tmp = (tmp & ~0x3f) | (tm.tm_hour & 0x3f);
+	} else {
+		/* 12 hour format, with 0x2 for pm */
+		tmp = tmp & ~0x3f;
+		if (tm.tm_hour >= 12) {
+			tmp |= 0x20;
+			tm.tm_hour -= 12;
+		}
+		tm.tm_hour = bin2bcd(tm.tm_hour);
+		tmp |= tm.tm_hour;
+	}
+	xicor_write(X1241REG_HR, tmp);
+
+	xicor_write(X1241REG_SR, 0);
+	spin_unlock_irqrestore(&rtc_lock, flags);
+
+	return 0;
+}
+
+time64_t xicor_get_time(void)
+{
+	unsigned int year, mon, day, hour, min, sec, y2k;
+	unsigned long flags;
+
+	spin_lock_irqsave(&rtc_lock, flags);
+	sec = xicor_read(X1241REG_SC);
+	min = xicor_read(X1241REG_MN);
+	hour = xicor_read(X1241REG_HR);
+
+	if (hour & X1241REG_HR_MIL) {
+		hour &= 0x3f;
+	} else {
+		if (hour & 0x20)
+			hour = (hour & 0xf) + 0x12;
+	}
+
+	day = xicor_read(X1241REG_DT);
+	mon = xicor_read(X1241REG_MO);
+	year = xicor_read(X1241REG_YR);
+	y2k = xicor_read(X1241REG_Y2K);
+	spin_unlock_irqrestore(&rtc_lock, flags);
+
+	sec = bcd2bin(sec);
+	min = bcd2bin(min);
+	hour = bcd2bin(hour);
+	day = bcd2bin(day);
+	mon = bcd2bin(mon);
+	year = bcd2bin(year);
+	y2k = bcd2bin(y2k);
+
+	year += (y2k * 100);
+
+	return mktime64(year, mon, day, hour, min, sec);
+}
+
+int xicor_probe(void)
+{
+	return xicor_read(X1241REG_SC) != -1;
+}
diff --git a/arch/mips/sibyte/swarm/setup.c b/arch/mips/sibyte/swarm/setup.c
new file mode 100644
index 000000000..72a31eeee
--- /dev/null
+++ b/arch/mips/sibyte/swarm/setup.c
@@ -0,0 +1,170 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2000, 2001, 2002, 2003, 2004 Broadcom Corporation
+ * Copyright (C) 2004 by Ralf Baechle (ralf@linux-mips.org)
+ */
+
+/*
+ * Setup code for the SWARM board
+ */
+
+#include <linux/spinlock.h>
+#include <linux/mm.h>
+#include <linux/memblock.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/screen_info.h>
+#include <linux/initrd.h>
+
+#include <asm/irq.h>
+#include <asm/io.h>
+#include <asm/bootinfo.h>
+#include <asm/mipsregs.h>
+#include <asm/reboot.h>
+#include <asm/time.h>
+#include <asm/traps.h>
+#include <asm/sibyte/sb1250.h>
+#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80)
+#include <asm/sibyte/bcm1480_regs.h>
+#elif defined(CONFIG_SIBYTE_SB1250) || defined(CONFIG_SIBYTE_BCM112X)
+#include <asm/sibyte/sb1250_regs.h>
+#else
+#error invalid SiByte board configuration
+#endif
+#include <asm/sibyte/sb1250_genbus.h>
+#include <asm/sibyte/board.h>
+
+#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80)
+extern void bcm1480_setup(void);
+#elif defined(CONFIG_SIBYTE_SB1250) || defined(CONFIG_SIBYTE_BCM112X)
+extern void sb1250_setup(void);
+#else
+#error invalid SiByte board configuration
+#endif
+
+extern int xicor_probe(void);
+extern int xicor_set_time(time64_t);
+extern time64_t xicor_get_time(void);
+
+extern int m41t81_probe(void);
+extern int m41t81_set_time(time64_t);
+extern time64_t m41t81_get_time(void);
+
+const char *get_system_type(void)
+{
+	return "SiByte " SIBYTE_BOARD_NAME;
+}
+
+int swarm_be_handler(struct pt_regs *regs, int is_fixup)
+{
+	if (!is_fixup && (regs->cp0_cause & 4)) {
+		/* Data bus error - print PA */
+		printk("DBE physical address: %010Lx\n",
+		       __read_64bit_c0_register($26, 1));
+	}
+	return is_fixup ? MIPS_BE_FIXUP : MIPS_BE_FATAL;
+}
+
+enum swarm_rtc_type {
+	RTC_NONE,
+	RTC_XICOR,
+	RTC_M41T81,
+};
+
+enum swarm_rtc_type swarm_rtc_type;
+
+void read_persistent_clock64(struct timespec64 *ts)
+{
+	time64_t sec;
+
+	switch (swarm_rtc_type) {
+	case RTC_XICOR:
+		sec = xicor_get_time();
+		break;
+
+	case RTC_M41T81:
+		sec = m41t81_get_time();
+		break;
+
+	case RTC_NONE:
+	default:
+		sec = mktime64(2000, 1, 1, 0, 0, 0);
+		break;
+	}
+	ts->tv_sec = sec;
+	ts->tv_nsec = 0;
+}
+
+int update_persistent_clock64(struct timespec64 now)
+{
+	time64_t sec = now.tv_sec;
+
+	switch (swarm_rtc_type) {
+	case RTC_XICOR:
+		return xicor_set_time(sec);
+
+	case RTC_M41T81:
+		return m41t81_set_time(sec);
+
+	case RTC_NONE:
+	default:
+		return -1;
+	}
+}
+
+void __init plat_mem_setup(void)
+{
+#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80)
+	bcm1480_setup();
+#elif defined(CONFIG_SIBYTE_SB1250) || defined(CONFIG_SIBYTE_BCM112X)
+	sb1250_setup();
+#else
+#error invalid SiByte board configuration
+#endif
+
+	mips_set_be_handler(swarm_be_handler);
+
+	if (xicor_probe())
+		swarm_rtc_type = RTC_XICOR;
+	if (m41t81_probe())
+		swarm_rtc_type = RTC_M41T81;
+
+#ifdef CONFIG_VT
+	screen_info = (struct screen_info) {
+		.orig_video_page	= 52,
+		.orig_video_mode	= 3,
+		.orig_video_cols	= 80,
+		.flags			= 12,
+		.orig_video_ega_bx	= 3,
+		.orig_video_lines	= 25,
+		.orig_video_isVGA	= 0x22,
+		.orig_video_points	= 16,
+       };
+       /* XXXKW for CFE, get lines/cols from environment */
+#endif
+}
+
+#ifdef LEDS_PHYS
+
+#ifdef CONFIG_SIBYTE_CARMEL
+/* XXXKW need to detect Monterey/LittleSur/etc */
+#undef LEDS_PHYS
+#define LEDS_PHYS MLEDS_PHYS
+#endif
+
+void setleds(char *str)
+{
+	void *reg;
+	int i;
+
+	for (i = 0; i < 4; i++) {
+		reg = IOADDR(LEDS_PHYS) + 0x20 + ((3 - i) << 3);
+
+		if (!str[i])
+			writeb(' ', reg);
+		else
+			writeb(str[i], reg);
+	}
+}
+
+#endif /* LEDS_PHYS */
diff --git a/arch/mips/sibyte/swarm/swarm-i2c.c b/arch/mips/sibyte/swarm/swarm-i2c.c
new file mode 100644
index 000000000..1ed2dc96d
--- /dev/null
+++ b/arch/mips/sibyte/swarm/swarm-i2c.c
@@ -0,0 +1,31 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ *	Broadcom BCM91250A (SWARM), etc. I2C platform setup.
+ *
+ *	Copyright (c) 2008  Maciej W. Rozycki
+ */
+
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+
+
+static struct i2c_board_info swarm_i2c_info1[] __initdata = {
+	{
+		I2C_BOARD_INFO("m41t81", 0x68),
+	},
+};
+
+static int __init swarm_i2c_init(void)
+{
+	int err;
+
+	err = i2c_register_board_info(1, swarm_i2c_info1,
+				      ARRAY_SIZE(swarm_i2c_info1));
+	if (err < 0)
+		printk(KERN_ERR
+		       "swarm-i2c: cannot register board I2C devices\n");
+	return err;
+}
+
+arch_initcall(swarm_i2c_init);
diff --git a/arch/mips/sni/Makefile b/arch/mips/sni/Makefile
new file mode 100644
index 000000000..6d97c3e96
--- /dev/null
+++ b/arch/mips/sni/Makefile
@@ -0,0 +1,7 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Makefile for the SNI specific part of the kernel
+#
+
+obj-y += irq.o reset.o setup.o a20r.o rm200.o pcimt.o pcit.o time.o
+obj-$(CONFIG_EISA) += eisa.o
diff --git a/arch/mips/sni/Platform b/arch/mips/sni/Platform
new file mode 100644
index 000000000..b0b3dde0b
--- /dev/null
+++ b/arch/mips/sni/Platform
@@ -0,0 +1,10 @@
+#
+# SNI RM
+#
+cflags-$(CONFIG_SNI_RM)		+= -I$(srctree)/arch/mips/include/asm/mach-rm
+ifdef CONFIG_CPU_LITTLE_ENDIAN
+load-$(CONFIG_SNI_RM)		+= 0xffffffff80600000
+else
+load-$(CONFIG_SNI_RM)		+= 0xffffffff80030000
+endif
+all-$(CONFIG_SNI_RM)		:= $(COMPRESSION_FNAME).ecoff
diff --git a/arch/mips/sni/a20r.c b/arch/mips/sni/a20r.c
new file mode 100644
index 000000000..eeeec18c4
--- /dev/null
+++ b/arch/mips/sni/a20r.c
@@ -0,0 +1,256 @@
+/*
+ * A20R specific code
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2006 Thomas Bogendoerfer (tsbogend@alpha.franken.de)
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/platform_device.h>
+#include <linux/serial_8250.h>
+
+#include <asm/sni.h>
+#include <asm/time.h>
+
+#define PORT(_base,_irq)				\
+	{						\
+		.iobase		= _base,		\
+		.irq		= _irq,			\
+		.uartclk	= 1843200,		\
+		.iotype		= UPIO_PORT,		\
+		.flags		= UPF_BOOT_AUTOCONF,	\
+	}
+
+static struct plat_serial8250_port a20r_data[] = {
+	PORT(0x3f8, 4),
+	PORT(0x2f8, 3),
+	{ },
+};
+
+static struct platform_device a20r_serial8250_device = {
+	.name			= "serial8250",
+	.id			= PLAT8250_DEV_PLATFORM,
+	.dev			= {
+		.platform_data	= a20r_data,
+	},
+};
+
+static struct resource a20r_ds1216_rsrc[] = {
+	{
+		.start = 0x1c081ffc,
+		.end   = 0x1c081fff,
+		.flags = IORESOURCE_MEM
+	}
+};
+
+static struct platform_device a20r_ds1216_device = {
+	.name		= "rtc-ds1216",
+	.num_resources	= ARRAY_SIZE(a20r_ds1216_rsrc),
+	.resource	= a20r_ds1216_rsrc
+};
+
+static struct resource snirm_82596_rsrc[] = {
+	{
+		.start = 0x18000000,
+		.end   = 0x18000004,
+		.flags = IORESOURCE_MEM
+	},
+	{
+		.start = 0x18010000,
+		.end   = 0x18010004,
+		.flags = IORESOURCE_MEM
+	},
+	{
+		.start = 0x1ff00000,
+		.end   = 0x1ff00020,
+		.flags = IORESOURCE_MEM
+	},
+	{
+		.start = 22,
+		.end   = 22,
+		.flags = IORESOURCE_IRQ
+	},
+	{
+		.flags = 0x01		     /* 16bit mpu port access */
+	}
+};
+
+static struct platform_device snirm_82596_pdev = {
+	.name		= "snirm_82596",
+	.num_resources	= ARRAY_SIZE(snirm_82596_rsrc),
+	.resource	= snirm_82596_rsrc
+};
+
+static struct resource snirm_53c710_rsrc[] = {
+	{
+		.start = 0x19000000,
+		.end   = 0x190fffff,
+		.flags = IORESOURCE_MEM
+	},
+	{
+		.start = 19,
+		.end   = 19,
+		.flags = IORESOURCE_IRQ
+	}
+};
+
+static struct platform_device snirm_53c710_pdev = {
+	.name		= "snirm_53c710",
+	.num_resources	= ARRAY_SIZE(snirm_53c710_rsrc),
+	.resource	= snirm_53c710_rsrc
+};
+
+static struct resource sc26xx_rsrc[] = {
+	{
+		.start = 0x1c070000,
+		.end   = 0x1c0700ff,
+		.flags = IORESOURCE_MEM
+	},
+	{
+		.start = 20,
+		.end   = 20,
+		.flags = IORESOURCE_IRQ
+	}
+};
+
+#include <linux/platform_data/serial-sccnxp.h>
+
+static struct sccnxp_pdata sccnxp_data = {
+	.reg_shift	= 2,
+	.mctrl_cfg[0]	= MCTRL_SIG(DTR_OP, LINE_OP7) |
+			  MCTRL_SIG(RTS_OP, LINE_OP3) |
+			  MCTRL_SIG(DSR_IP, LINE_IP5) |
+			  MCTRL_SIG(DCD_IP, LINE_IP6),
+	.mctrl_cfg[1]	= MCTRL_SIG(DTR_OP, LINE_OP2) |
+			  MCTRL_SIG(RTS_OP, LINE_OP1) |
+			  MCTRL_SIG(DSR_IP, LINE_IP0) |
+			  MCTRL_SIG(CTS_IP, LINE_IP1) |
+			  MCTRL_SIG(DCD_IP, LINE_IP2) |
+			  MCTRL_SIG(RNG_IP, LINE_IP3),
+};
+
+static struct platform_device sc26xx_pdev = {
+	.name		= "sc2681",
+	.resource	= sc26xx_rsrc,
+	.num_resources	= ARRAY_SIZE(sc26xx_rsrc),
+	.dev	= {
+		.platform_data	= &sccnxp_data,
+	},
+};
+
+/*
+ * Trigger chipset to update CPU's CAUSE IP field
+ */
+static u32 a20r_update_cause_ip(void)
+{
+	u32 status = read_c0_status();
+
+	write_c0_status(status | 0x00010000);
+	asm volatile(
+	"	.set	push			\n"
+	"	.set	noat			\n"
+	"	.set	noreorder		\n"
+	"	lw	$1, 0(%0)		\n"
+	"	sb	$0, 0(%1)		\n"
+	"	sync				\n"
+	"	lb	%1, 0(%1)		\n"
+	"	b	1f			\n"
+	"	ori	%1, $1, 2		\n"
+	"	.align	8			\n"
+	"1:					\n"
+	"	nop				\n"
+	"	sw	%1, 0(%0)		\n"
+	"	sync				\n"
+	"	li	%1, 0x20		\n"
+	"2:					\n"
+	"	nop				\n"
+	"	bnez	%1,2b			\n"
+	"	addiu	%1, -1			\n"
+	"	sw	$1, 0(%0)		\n"
+	"	sync				\n"
+		".set	pop			\n"
+	:
+	: "Jr" (PCIMT_UCONF), "Jr" (0xbc000000));
+	write_c0_status(status);
+
+	return status;
+}
+
+static inline void unmask_a20r_irq(struct irq_data *d)
+{
+	set_c0_status(0x100 << (d->irq - SNI_A20R_IRQ_BASE));
+	irq_enable_hazard();
+}
+
+static inline void mask_a20r_irq(struct irq_data *d)
+{
+	clear_c0_status(0x100 << (d->irq - SNI_A20R_IRQ_BASE));
+	irq_disable_hazard();
+}
+
+static struct irq_chip a20r_irq_type = {
+	.name		= "A20R",
+	.irq_mask	= mask_a20r_irq,
+	.irq_unmask	= unmask_a20r_irq,
+};
+
+/*
+ * hwint 0 receive all interrupts
+ */
+static void a20r_hwint(void)
+{
+	u32 cause, status;
+	int irq;
+
+	clear_c0_status(IE_IRQ0);
+	status = a20r_update_cause_ip();
+	cause = read_c0_cause();
+
+	irq = ffs(((cause & status) >> 8) & 0xf8);
+	if (likely(irq > 0))
+		do_IRQ(SNI_A20R_IRQ_BASE + irq - 1);
+
+	a20r_update_cause_ip();
+	set_c0_status(IE_IRQ0);
+}
+
+void __init sni_a20r_irq_init(void)
+{
+	int i;
+
+	for (i = SNI_A20R_IRQ_BASE + 2 ; i < SNI_A20R_IRQ_BASE + 8; i++)
+		irq_set_chip_and_handler(i, &a20r_irq_type, handle_level_irq);
+	sni_hwint = a20r_hwint;
+	change_c0_status(ST0_IM, IE_IRQ0);
+	if (request_irq(SNI_A20R_IRQ_BASE + 3, sni_isa_irq_handler,
+			IRQF_SHARED, "ISA", sni_isa_irq_handler))
+		pr_err("Failed to register ISA interrupt\n");
+}
+
+void sni_a20r_init(void)
+{
+	/* FIXME, remove if not needed */
+}
+
+static int __init snirm_a20r_setup_devinit(void)
+{
+	switch (sni_brd_type) {
+	case SNI_BRD_TOWER_OASIC:
+	case SNI_BRD_MINITOWER:
+		platform_device_register(&snirm_82596_pdev);
+		platform_device_register(&snirm_53c710_pdev);
+		platform_device_register(&sc26xx_pdev);
+		platform_device_register(&a20r_serial8250_device);
+		platform_device_register(&a20r_ds1216_device);
+		sni_eisa_root_init();
+		break;
+	}
+	return 0;
+}
+
+device_initcall(snirm_a20r_setup_devinit);
diff --git a/arch/mips/sni/eisa.c b/arch/mips/sni/eisa.c
new file mode 100644
index 000000000..483a43d07
--- /dev/null
+++ b/arch/mips/sni/eisa.c
@@ -0,0 +1,49 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Virtual EISA root driver.
+ * Acts as a placeholder if we don't have a proper EISA bridge.
+ *
+ * (C) 2003 Marc Zyngier <maz@wild-wind.fr.eu.org>
+ * modified for SNI usage by Thomas Bogendoerfer
+ */
+
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/eisa.h>
+#include <linux/init.h>
+
+/* The default EISA device parent (virtual root device).
+ * Now use a platform device, since that's the obvious choice. */
+
+static struct platform_device eisa_root_dev = {
+	.name = "eisa",
+	.id   = 0,
+};
+
+static struct eisa_root_device eisa_bus_root = {
+	.dev	       = &eisa_root_dev.dev,
+	.bus_base_addr = 0,
+	.res	       = &ioport_resource,
+	.slots	       = EISA_MAX_SLOTS,
+	.dma_mask      = 0xffffffff,
+	.force_probe   = 1,
+};
+
+int __init sni_eisa_root_init(void)
+{
+	int r;
+
+	r = platform_device_register(&eisa_root_dev);
+	if (!r)
+		return r;
+
+	dev_set_drvdata(&eisa_root_dev.dev, &eisa_bus_root);
+
+	if (eisa_root_register(&eisa_bus_root)) {
+		/* A real bridge may have been registered before
+		 * us. So quietly unregister. */
+		platform_device_unregister(&eisa_root_dev);
+		return -1;
+	}
+	return 0;
+}
diff --git a/arch/mips/sni/irq.c b/arch/mips/sni/irq.c
new file mode 100644
index 000000000..dec89afc9
--- /dev/null
+++ b/arch/mips/sni/irq.c
@@ -0,0 +1,76 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1992 Linus Torvalds
+ * Copyright (C) 1994 - 2000 Ralf Baechle
+ * Copyright (C) 2006 Thomas Bogendoerfer
+ */
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/kernel.h>
+
+#include <asm/i8259.h>
+#include <asm/io.h>
+#include <asm/sni.h>
+#include <asm/irq.h>
+#include <asm/irq_cpu.h>
+
+void (*sni_hwint)(void);
+
+asmlinkage void plat_irq_dispatch(void)
+{
+	sni_hwint();
+}
+
+/* ISA irq handler */
+irqreturn_t sni_isa_irq_handler(int dummy, void *p)
+{
+	int irq;
+
+	irq = i8259_irq();
+	if (unlikely(irq < 0))
+		return IRQ_NONE;
+
+	generic_handle_irq(irq);
+	return IRQ_HANDLED;
+}
+
+/*
+ * On systems with i8259-style interrupt controllers we assume for
+ * driver compatibility reasons interrupts 0 - 15 to be the i8295
+ * interrupts even if the hardware uses a different interrupt numbering.
+ */
+void __init arch_init_irq(void)
+{
+	init_i8259_irqs();			/* Integrated i8259  */
+	switch (sni_brd_type) {
+	case SNI_BRD_10:
+	case SNI_BRD_10NEW:
+	case SNI_BRD_TOWER_OASIC:
+	case SNI_BRD_MINITOWER:
+		sni_a20r_irq_init();
+		break;
+
+	case SNI_BRD_PCI_TOWER:
+		sni_pcit_irq_init();
+		break;
+
+	case SNI_BRD_PCI_TOWER_CPLUS:
+		sni_pcit_cplus_irq_init();
+		break;
+
+	case SNI_BRD_RM200:
+		sni_rm200_irq_init();
+		break;
+
+	case SNI_BRD_PCI_MTOWER:
+	case SNI_BRD_PCI_DESKTOP:
+	case SNI_BRD_PCI_MTOWER_CPLUS:
+		sni_pcimt_irq_init();
+		break;
+	}
+}
diff --git a/arch/mips/sni/pcimt.c b/arch/mips/sni/pcimt.c
new file mode 100644
index 000000000..12336c2a6
--- /dev/null
+++ b/arch/mips/sni/pcimt.c
@@ -0,0 +1,332 @@
+/*
+ * PCIMT specific code
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1996, 97, 98, 2000, 03, 04, 06 Ralf Baechle (ralf@linux-mips.org)
+ * Copyright (C) 2006,2007 Thomas Bogendoerfer (tsbogend@alpha.franken.de)
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/pci.h>
+#include <linux/serial_8250.h>
+
+#include <asm/sni.h>
+#include <asm/time.h>
+#include <asm/i8259.h>
+#include <asm/irq_cpu.h>
+
+#define cacheconf (*(volatile unsigned int *)PCIMT_CACHECONF)
+#define invspace (*(volatile unsigned int *)PCIMT_INVSPACE)
+
+static void __init sni_pcimt_sc_init(void)
+{
+	unsigned int scsiz, sc_size;
+
+	scsiz = cacheconf & 7;
+	if (scsiz == 0) {
+		printk("Second level cache is deactivated.\n");
+		return;
+	}
+	if (scsiz >= 6) {
+		printk("Invalid second level cache size configured, "
+		       "deactivating second level cache.\n");
+		cacheconf = 0;
+		return;
+	}
+
+	sc_size = 128 << scsiz;
+	printk("%dkb second level cache detected, deactivating.\n", sc_size);
+	cacheconf = 0;
+}
+
+
+/*
+ * A bit more gossip about the iron we're running on ...
+ */
+static inline void sni_pcimt_detect(void)
+{
+	char boardtype[80];
+	unsigned char csmsr;
+	char *p = boardtype;
+	unsigned int asic;
+
+	csmsr = *(volatile unsigned char *)PCIMT_CSMSR;
+
+	p += sprintf(p, "%s PCI", (csmsr & 0x80) ? "RM200" : "RM300");
+	if ((csmsr & 0x80) == 0)
+		p += sprintf(p, ", board revision %s",
+			     (csmsr & 0x20) ? "D" : "C");
+	asic = csmsr & 0x80;
+	asic = (csmsr & 0x08) ? asic : !asic;
+	p += sprintf(p, ", ASIC PCI Rev %s", asic ? "1.0" : "1.1");
+	printk("%s.\n", boardtype);
+}
+
+#define PORT(_base,_irq)				\
+	{						\
+		.iobase		= _base,		\
+		.irq		= _irq,			\
+		.uartclk	= 1843200,		\
+		.iotype		= UPIO_PORT,		\
+		.flags		= UPF_BOOT_AUTOCONF,	\
+	}
+
+static struct plat_serial8250_port pcimt_data[] = {
+	PORT(0x3f8, 4),
+	PORT(0x2f8, 3),
+	{ },
+};
+
+static struct platform_device pcimt_serial8250_device = {
+	.name			= "serial8250",
+	.id			= PLAT8250_DEV_PLATFORM,
+	.dev			= {
+		.platform_data	= pcimt_data,
+	},
+};
+
+static struct resource pcimt_cmos_rsrc[] = {
+	{
+		.start = 0x70,
+		.end   = 0x71,
+		.flags = IORESOURCE_IO
+	},
+	{
+		.start = 8,
+		.end   = 8,
+		.flags = IORESOURCE_IRQ
+	}
+};
+
+static struct platform_device pcimt_cmos_device = {
+	.name		= "rtc_cmos",
+	.num_resources	= ARRAY_SIZE(pcimt_cmos_rsrc),
+	.resource	= pcimt_cmos_rsrc
+};
+
+
+static struct resource sni_io_resource = {
+	.start	= 0x00000000UL,
+	.end	= 0x03bfffffUL,
+	.name	= "PCIMT IO MEM",
+	.flags	= IORESOURCE_IO,
+};
+
+static struct resource pcimt_io_resources[] = {
+	{
+		.start	= 0x00,
+		.end	= 0x1f,
+		.name	= "dma1",
+		.flags	= IORESOURCE_BUSY
+	}, {
+		.start	=  0x40,
+		.end	= 0x5f,
+		.name	= "timer",
+		.flags	= IORESOURCE_BUSY
+	}, {
+		.start	=  0x60,
+		.end	= 0x6f,
+		.name	= "keyboard",
+		.flags	= IORESOURCE_BUSY
+	}, {
+		.start	=  0x80,
+		.end	= 0x8f,
+		.name	= "dma page reg",
+		.flags	= IORESOURCE_BUSY
+	}, {
+		.start	=  0xc0,
+		.end	= 0xdf,
+		.name	= "dma2",
+		.flags	= IORESOURCE_BUSY
+	}, {
+		.start	=  0xcfc,
+		.end	= 0xcff,
+		.name	= "PCI config data",
+		.flags	= IORESOURCE_BUSY
+	}
+};
+
+static struct resource pcimt_mem_resources[] = {
+	{
+		/*
+		 * this region should only be 4 bytes long,
+		 * but it's 16MB on all RM300C I've checked
+		 */
+		.start	= 0x1a000000,
+		.end	= 0x1affffff,
+		.name	= "PCI INT ACK",
+		.flags	= IORESOURCE_BUSY
+	}
+};
+
+static struct resource sni_mem_resource = {
+	.start	= 0x18000000UL,
+	.end	= 0x1fbfffffUL,
+	.name	= "PCIMT PCI MEM",
+	.flags	= IORESOURCE_MEM
+};
+
+static void __init sni_pcimt_resource_init(void)
+{
+	int i;
+
+	/* request I/O space for devices used on all i[345]86 PCs */
+	for (i = 0; i < ARRAY_SIZE(pcimt_io_resources); i++)
+		request_resource(&sni_io_resource, pcimt_io_resources + i);
+	/* request MEM space for devices used on all i[345]86 PCs */
+	for (i = 0; i < ARRAY_SIZE(pcimt_mem_resources); i++)
+		request_resource(&sni_mem_resource, pcimt_mem_resources + i);
+}
+
+extern struct pci_ops sni_pcimt_ops;
+
+#ifdef CONFIG_PCI
+static struct pci_controller sni_controller = {
+	.pci_ops	= &sni_pcimt_ops,
+	.mem_resource	= &sni_mem_resource,
+	.mem_offset	= 0x00000000UL,
+	.io_resource	= &sni_io_resource,
+	.io_offset	= 0x00000000UL,
+	.io_map_base	= SNI_PORT_BASE
+};
+#endif
+
+static void enable_pcimt_irq(struct irq_data *d)
+{
+	unsigned int mask = 1 << (d->irq - PCIMT_IRQ_INT2);
+
+	*(volatile u8 *) PCIMT_IRQSEL |= mask;
+}
+
+void disable_pcimt_irq(struct irq_data *d)
+{
+	unsigned int mask = ~(1 << (d->irq - PCIMT_IRQ_INT2));
+
+	*(volatile u8 *) PCIMT_IRQSEL &= mask;
+}
+
+static struct irq_chip pcimt_irq_type = {
+	.name = "PCIMT",
+	.irq_mask = disable_pcimt_irq,
+	.irq_unmask = enable_pcimt_irq,
+};
+
+/*
+ * hwint0 should deal with MP agent, ASIC PCI, EISA NMI and debug
+ * button interrupts.  Later ...
+ */
+static void pcimt_hwint0(void)
+{
+	panic("Received int0 but no handler yet ...");
+}
+
+/*
+ * hwint 1 deals with EISA and SCSI interrupts,
+ *
+ * The EISA_INT bit in CSITPEND is high active, all others are low active.
+ */
+static void pcimt_hwint1(void)
+{
+	u8 pend = *(volatile char *)PCIMT_CSITPEND;
+	unsigned long flags;
+
+	if (pend & IT_EISA) {
+		int irq;
+		/*
+		 * Note: ASIC PCI's builtin interrupt acknowledge feature is
+		 * broken.  Using it may result in loss of some or all i8259
+		 * interrupts, so don't use PCIMT_INT_ACKNOWLEDGE ...
+		 */
+		irq = i8259_irq();
+		if (unlikely(irq < 0))
+			return;
+
+		do_IRQ(irq);
+	}
+
+	if (!(pend & IT_SCSI)) {
+		flags = read_c0_status();
+		clear_c0_status(ST0_IM);
+		do_IRQ(PCIMT_IRQ_SCSI);
+		write_c0_status(flags);
+	}
+}
+
+/*
+ * hwint 3 should deal with the PCI A - D interrupts,
+ */
+static void pcimt_hwint3(void)
+{
+	u8 pend = *(volatile char *)PCIMT_CSITPEND;
+	int irq;
+
+	pend &= (IT_INTA | IT_INTB | IT_INTC | IT_INTD);
+	pend ^= (IT_INTA | IT_INTB | IT_INTC | IT_INTD);
+	clear_c0_status(IE_IRQ3);
+	irq = PCIMT_IRQ_INT2 + ffs(pend) - 1;
+	do_IRQ(irq);
+	set_c0_status(IE_IRQ3);
+}
+
+static void sni_pcimt_hwint(void)
+{
+	u32 pending = read_c0_cause() & read_c0_status();
+
+	if (pending & C_IRQ5)
+		do_IRQ(MIPS_CPU_IRQ_BASE + 7);
+	else if (pending & C_IRQ4)
+		do_IRQ(MIPS_CPU_IRQ_BASE + 6);
+	else if (pending & C_IRQ3)
+		pcimt_hwint3();
+	else if (pending & C_IRQ1)
+		pcimt_hwint1();
+	else if (pending & C_IRQ0) {
+		pcimt_hwint0();
+	}
+}
+
+void __init sni_pcimt_irq_init(void)
+{
+	int i;
+
+	*(volatile u8 *) PCIMT_IRQSEL = IT_ETH | IT_EISA;
+	mips_cpu_irq_init();
+	/* Actually we've got more interrupts to handle ...  */
+	for (i = PCIMT_IRQ_INT2; i <= PCIMT_IRQ_SCSI; i++)
+		irq_set_chip_and_handler(i, &pcimt_irq_type, handle_level_irq);
+	sni_hwint = sni_pcimt_hwint;
+	change_c0_status(ST0_IM, IE_IRQ1|IE_IRQ3);
+}
+
+void __init sni_pcimt_init(void)
+{
+	sni_pcimt_detect();
+	sni_pcimt_sc_init();
+	ioport_resource.end = sni_io_resource.end;
+#ifdef CONFIG_PCI
+	PCIBIOS_MIN_IO = 0x9000;
+	register_pci_controller(&sni_controller);
+#endif
+	sni_pcimt_resource_init();
+}
+
+static int __init snirm_pcimt_setup_devinit(void)
+{
+	switch (sni_brd_type) {
+	case SNI_BRD_PCI_MTOWER:
+	case SNI_BRD_PCI_DESKTOP:
+	case SNI_BRD_PCI_MTOWER_CPLUS:
+		platform_device_register(&pcimt_serial8250_device);
+		platform_device_register(&pcimt_cmos_device);
+		break;
+	}
+
+	return 0;
+}
+
+device_initcall(snirm_pcimt_setup_devinit);
diff --git a/arch/mips/sni/pcit.c b/arch/mips/sni/pcit.c
new file mode 100644
index 000000000..b331fe22c
--- /dev/null
+++ b/arch/mips/sni/pcit.c
@@ -0,0 +1,295 @@
+/*
+ * PCI Tower specific code
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2006 Thomas Bogendoerfer (tsbogend@alpha.franken.de)
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/pci.h>
+#include <linux/serial_8250.h>
+
+#include <asm/sni.h>
+#include <asm/time.h>
+#include <asm/irq_cpu.h>
+
+
+#define PORT(_base,_irq)				\
+	{						\
+		.iobase		= _base,		\
+		.irq		= _irq,			\
+		.uartclk	= 1843200,		\
+		.iotype		= UPIO_PORT,		\
+		.flags		= UPF_BOOT_AUTOCONF,	\
+	}
+
+static struct plat_serial8250_port pcit_data[] = {
+	PORT(0x3f8, 0),
+	PORT(0x2f8, 3),
+	{ },
+};
+
+static struct platform_device pcit_serial8250_device = {
+	.name			= "serial8250",
+	.id			= PLAT8250_DEV_PLATFORM,
+	.dev			= {
+		.platform_data	= pcit_data,
+	},
+};
+
+static struct plat_serial8250_port pcit_cplus_data[] = {
+	PORT(0x3f8, 0),
+	PORT(0x2f8, 3),
+	PORT(0x3e8, 4),
+	PORT(0x2e8, 3),
+	{ },
+};
+
+static struct platform_device pcit_cplus_serial8250_device = {
+	.name			= "serial8250",
+	.id			= PLAT8250_DEV_PLATFORM,
+	.dev			= {
+		.platform_data	= pcit_cplus_data,
+	},
+};
+
+static struct resource pcit_cmos_rsrc[] = {
+	{
+		.start = 0x70,
+		.end   = 0x71,
+		.flags = IORESOURCE_IO
+	},
+	{
+		.start = 8,
+		.end   = 8,
+		.flags = IORESOURCE_IRQ
+	}
+};
+
+static struct platform_device pcit_cmos_device = {
+	.name		= "rtc_cmos",
+	.num_resources	= ARRAY_SIZE(pcit_cmos_rsrc),
+	.resource	= pcit_cmos_rsrc
+};
+
+static struct platform_device pcit_pcspeaker_pdev = {
+	.name		= "pcspkr",
+	.id		= -1,
+};
+
+static struct resource sni_io_resource = {
+	.start	= 0x00000000UL,
+	.end	= 0x03bfffffUL,
+	.name	= "PCIT IO",
+	.flags	= IORESOURCE_IO,
+};
+
+static struct resource pcit_io_resources[] = {
+	{
+		.start	= 0x00,
+		.end	= 0x1f,
+		.name	= "dma1",
+		.flags	= IORESOURCE_BUSY
+	}, {
+		.start	=  0x40,
+		.end	= 0x5f,
+		.name	= "timer",
+		.flags	= IORESOURCE_BUSY
+	}, {
+		.start	=  0x60,
+		.end	= 0x6f,
+		.name	= "keyboard",
+		.flags	= IORESOURCE_BUSY
+	}, {
+		.start	=  0x80,
+		.end	= 0x8f,
+		.name	= "dma page reg",
+		.flags	= IORESOURCE_BUSY
+	}, {
+		.start	=  0xc0,
+		.end	= 0xdf,
+		.name	= "dma2",
+		.flags	= IORESOURCE_BUSY
+	}, {
+		.start	=  0xcf8,
+		.end	= 0xcfb,
+		.name	= "PCI config addr",
+		.flags	= IORESOURCE_BUSY
+	}, {
+		.start	=  0xcfc,
+		.end	= 0xcff,
+		.name	= "PCI config data",
+		.flags	= IORESOURCE_BUSY
+	}
+};
+
+static void __init sni_pcit_resource_init(void)
+{
+	int i;
+
+	/* request I/O space for devices used on all i[345]86 PCs */
+	for (i = 0; i < ARRAY_SIZE(pcit_io_resources); i++)
+		request_resource(&sni_io_resource, pcit_io_resources + i);
+}
+
+
+extern struct pci_ops sni_pcit_ops;
+
+#ifdef CONFIG_PCI
+static struct resource sni_mem_resource = {
+	.start	= 0x18000000UL,
+	.end	= 0x1fbfffffUL,
+	.name	= "PCIT PCI MEM",
+	.flags	= IORESOURCE_MEM
+};
+
+static struct pci_controller sni_pcit_controller = {
+	.pci_ops	= &sni_pcit_ops,
+	.mem_resource	= &sni_mem_resource,
+	.mem_offset	= 0x00000000UL,
+	.io_resource	= &sni_io_resource,
+	.io_offset	= 0x00000000UL,
+	.io_map_base	= SNI_PORT_BASE
+};
+#endif /* CONFIG_PCI */
+
+static void enable_pcit_irq(struct irq_data *d)
+{
+	u32 mask = 1 << (d->irq - SNI_PCIT_INT_START + 24);
+
+	*(volatile u32 *)SNI_PCIT_INT_REG |= mask;
+}
+
+void disable_pcit_irq(struct irq_data *d)
+{
+	u32 mask = 1 << (d->irq - SNI_PCIT_INT_START + 24);
+
+	*(volatile u32 *)SNI_PCIT_INT_REG &= ~mask;
+}
+
+static struct irq_chip pcit_irq_type = {
+	.name = "PCIT",
+	.irq_mask = disable_pcit_irq,
+	.irq_unmask = enable_pcit_irq,
+};
+
+static void pcit_hwint1(void)
+{
+	u32 pending = *(volatile u32 *)SNI_PCIT_INT_REG;
+	int irq;
+
+	clear_c0_status(IE_IRQ1);
+	irq = ffs((pending >> 16) & 0x7f);
+
+	if (likely(irq > 0))
+		do_IRQ(irq + SNI_PCIT_INT_START - 1);
+	set_c0_status(IE_IRQ1);
+}
+
+static void pcit_hwint0(void)
+{
+	u32 pending = *(volatile u32 *)SNI_PCIT_INT_REG;
+	int irq;
+
+	clear_c0_status(IE_IRQ0);
+	irq = ffs((pending >> 16) & 0x3f);
+
+	if (likely(irq > 0))
+		do_IRQ(irq + SNI_PCIT_INT_START - 1);
+	set_c0_status(IE_IRQ0);
+}
+
+static void sni_pcit_hwint(void)
+{
+	u32 pending = read_c0_cause() & read_c0_status();
+
+	if (pending & C_IRQ1)
+		pcit_hwint1();
+	else if (pending & C_IRQ2)
+		do_IRQ(MIPS_CPU_IRQ_BASE + 4);
+	else if (pending & C_IRQ3)
+		do_IRQ(MIPS_CPU_IRQ_BASE + 5);
+	else if (pending & C_IRQ5)
+		do_IRQ(MIPS_CPU_IRQ_BASE + 7);
+}
+
+static void sni_pcit_hwint_cplus(void)
+{
+	u32 pending = read_c0_cause() & read_c0_status();
+
+	if (pending & C_IRQ0)
+		pcit_hwint0();
+	else if (pending & C_IRQ1)
+		do_IRQ(MIPS_CPU_IRQ_BASE + 3);
+	else if (pending & C_IRQ2)
+		do_IRQ(MIPS_CPU_IRQ_BASE + 4);
+	else if (pending & C_IRQ3)
+		do_IRQ(MIPS_CPU_IRQ_BASE + 5);
+	else if (pending & C_IRQ5)
+		do_IRQ(MIPS_CPU_IRQ_BASE + 7);
+}
+
+void __init sni_pcit_irq_init(void)
+{
+	int i;
+
+	mips_cpu_irq_init();
+	for (i = SNI_PCIT_INT_START; i <= SNI_PCIT_INT_END; i++)
+		irq_set_chip_and_handler(i, &pcit_irq_type, handle_level_irq);
+	*(volatile u32 *)SNI_PCIT_INT_REG = 0;
+	sni_hwint = sni_pcit_hwint;
+	change_c0_status(ST0_IM, IE_IRQ1);
+	if (request_irq(SNI_PCIT_INT_START + 6, sni_isa_irq_handler, 0, "ISA",
+			NULL))
+		pr_err("Failed to register ISA interrupt\n");
+}
+
+void __init sni_pcit_cplus_irq_init(void)
+{
+	int i;
+
+	mips_cpu_irq_init();
+	for (i = SNI_PCIT_INT_START; i <= SNI_PCIT_INT_END; i++)
+		irq_set_chip_and_handler(i, &pcit_irq_type, handle_level_irq);
+	*(volatile u32 *)SNI_PCIT_INT_REG = 0x40000000;
+	sni_hwint = sni_pcit_hwint_cplus;
+	change_c0_status(ST0_IM, IE_IRQ0);
+	if (request_irq(MIPS_CPU_IRQ_BASE + 3, sni_isa_irq_handler, 0, "ISA",
+			NULL))
+		pr_err("Failed to register ISA interrupt\n");
+}
+
+void __init sni_pcit_init(void)
+{
+	ioport_resource.end = sni_io_resource.end;
+#ifdef CONFIG_PCI
+	PCIBIOS_MIN_IO = 0x9000;
+	register_pci_controller(&sni_pcit_controller);
+#endif
+	sni_pcit_resource_init();
+}
+
+static int __init snirm_pcit_setup_devinit(void)
+{
+	switch (sni_brd_type) {
+	case SNI_BRD_PCI_TOWER:
+		platform_device_register(&pcit_serial8250_device);
+		platform_device_register(&pcit_cmos_device);
+		platform_device_register(&pcit_pcspeaker_pdev);
+		break;
+
+	case SNI_BRD_PCI_TOWER_CPLUS:
+		platform_device_register(&pcit_cplus_serial8250_device);
+		platform_device_register(&pcit_cmos_device);
+		platform_device_register(&pcit_pcspeaker_pdev);
+		break;
+	}
+	return 0;
+}
+
+device_initcall(snirm_pcit_setup_devinit);
diff --git a/arch/mips/sni/reset.c b/arch/mips/sni/reset.c
new file mode 100644
index 000000000..66f963d8d
--- /dev/null
+++ b/arch/mips/sni/reset.c
@@ -0,0 +1,48 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ *  linux/arch/mips/sni/process.c
+ *
+ *  Reset a SNI machine.
+ */
+#include <linux/delay.h>
+
+#include <asm/io.h>
+#include <asm/reboot.h>
+#include <asm/sni.h>
+
+/*
+ * This routine reboots the machine by asking the keyboard
+ * controller to pulse the reset-line low. We try that for a while,
+ * and if it doesn't work, we do some other stupid things.
+ */
+static inline void kb_wait(void)
+{
+	int i;
+
+	for (i = 0; i < 0x10000; i++)
+		if ((inb_p(0x64) & 0x02) == 0)
+			break;
+}
+
+/* XXX This ends up at the ARC firmware prompt ...  */
+void sni_machine_restart(char *command)
+{
+	int i;
+
+	/* This does a normal via the keyboard controller like a PC.
+	   We can do that easier ...  */
+	local_irq_disable();
+	for (;;) {
+		for (i = 0; i < 100; i++) {
+			kb_wait();
+			udelay(50);
+			outb_p(0xfe, 0x64);	 /* pulse reset low */
+			udelay(50);
+		}
+	}
+}
+
+void sni_machine_power_off(void)
+{
+	*(volatile unsigned char *)PCIMT_CSWCSM = 0xfd;
+}
diff --git a/arch/mips/sni/rm200.c b/arch/mips/sni/rm200.c
new file mode 100644
index 000000000..d84744ca8
--- /dev/null
+++ b/arch/mips/sni/rm200.c
@@ -0,0 +1,485 @@
+/*
+ * RM200 specific code
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2006,2007 Thomas Bogendoerfer (tsbogend@alpha.franken.de)
+ *
+ * i8259 parts ripped out of arch/mips/kernel/i8259.c
+ */
+
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/platform_device.h>
+#include <linux/serial_8250.h>
+#include <linux/io.h>
+
+#include <asm/sni.h>
+#include <asm/time.h>
+#include <asm/irq_cpu.h>
+
+#define RM200_I8259A_IRQ_BASE 32
+
+#define MEMPORT(_base,_irq)				\
+	{						\
+		.mapbase	= _base,		\
+		.irq		= _irq,			\
+		.uartclk	= 1843200,		\
+		.iotype		= UPIO_MEM,		\
+		.flags		= UPF_BOOT_AUTOCONF|UPF_IOREMAP, \
+	}
+
+static struct plat_serial8250_port rm200_data[] = {
+	MEMPORT(0x160003f8, RM200_I8259A_IRQ_BASE + 4),
+	MEMPORT(0x160002f8, RM200_I8259A_IRQ_BASE + 3),
+	{ },
+};
+
+static struct platform_device rm200_serial8250_device = {
+	.name			= "serial8250",
+	.id			= PLAT8250_DEV_PLATFORM,
+	.dev			= {
+		.platform_data	= rm200_data,
+	},
+};
+
+static struct resource rm200_ds1216_rsrc[] = {
+	{
+		.start = 0x1cd41ffc,
+		.end   = 0x1cd41fff,
+		.flags = IORESOURCE_MEM
+	}
+};
+
+static struct platform_device rm200_ds1216_device = {
+	.name		= "rtc-ds1216",
+	.num_resources	= ARRAY_SIZE(rm200_ds1216_rsrc),
+	.resource	= rm200_ds1216_rsrc
+};
+
+static struct resource snirm_82596_rm200_rsrc[] = {
+	{
+		.start = 0x18000000,
+		.end   = 0x180fffff,
+		.flags = IORESOURCE_MEM
+	},
+	{
+		.start = 0x1b000000,
+		.end   = 0x1b000004,
+		.flags = IORESOURCE_MEM
+	},
+	{
+		.start = 0x1ff00000,
+		.end   = 0x1ff00020,
+		.flags = IORESOURCE_MEM
+	},
+	{
+		.start = 27,
+		.end   = 27,
+		.flags = IORESOURCE_IRQ
+	},
+	{
+		.flags = 0x00
+	}
+};
+
+static struct platform_device snirm_82596_rm200_pdev = {
+	.name		= "snirm_82596",
+	.num_resources	= ARRAY_SIZE(snirm_82596_rm200_rsrc),
+	.resource	= snirm_82596_rm200_rsrc
+};
+
+static struct resource snirm_53c710_rm200_rsrc[] = {
+	{
+		.start = 0x19000000,
+		.end   = 0x190fffff,
+		.flags = IORESOURCE_MEM
+	},
+	{
+		.start = 26,
+		.end   = 26,
+		.flags = IORESOURCE_IRQ
+	}
+};
+
+static struct platform_device snirm_53c710_rm200_pdev = {
+	.name		= "snirm_53c710",
+	.num_resources	= ARRAY_SIZE(snirm_53c710_rm200_rsrc),
+	.resource	= snirm_53c710_rm200_rsrc
+};
+
+static int __init snirm_setup_devinit(void)
+{
+	if (sni_brd_type == SNI_BRD_RM200) {
+		platform_device_register(&rm200_serial8250_device);
+		platform_device_register(&rm200_ds1216_device);
+		platform_device_register(&snirm_82596_rm200_pdev);
+		platform_device_register(&snirm_53c710_rm200_pdev);
+		sni_eisa_root_init();
+	}
+	return 0;
+}
+
+device_initcall(snirm_setup_devinit);
+
+/*
+ * RM200 has an ISA and an EISA bus. The iSA bus is only used
+ * for onboard devices and also has twi i8259 PICs. Since these
+ * PICs are no accessible via inb/outb the following code uses
+ * readb/writeb to access them
+ */
+
+static DEFINE_RAW_SPINLOCK(sni_rm200_i8259A_lock);
+#define PIC_CMD	   0x00
+#define PIC_IMR	   0x01
+#define PIC_ISR	   PIC_CMD
+#define PIC_POLL   PIC_ISR
+#define PIC_OCW3   PIC_ISR
+
+/* i8259A PIC related value */
+#define PIC_CASCADE_IR		2
+#define MASTER_ICW4_DEFAULT	0x01
+#define SLAVE_ICW4_DEFAULT	0x01
+
+/*
+ * This contains the irq mask for both 8259A irq controllers,
+ */
+static unsigned int rm200_cached_irq_mask = 0xffff;
+static __iomem u8 *rm200_pic_master;
+static __iomem u8 *rm200_pic_slave;
+
+#define cached_master_mask	(rm200_cached_irq_mask)
+#define cached_slave_mask	(rm200_cached_irq_mask >> 8)
+
+static void sni_rm200_disable_8259A_irq(struct irq_data *d)
+{
+	unsigned int mask, irq = d->irq - RM200_I8259A_IRQ_BASE;
+	unsigned long flags;
+
+	mask = 1 << irq;
+	raw_spin_lock_irqsave(&sni_rm200_i8259A_lock, flags);
+	rm200_cached_irq_mask |= mask;
+	if (irq & 8)
+		writeb(cached_slave_mask, rm200_pic_slave + PIC_IMR);
+	else
+		writeb(cached_master_mask, rm200_pic_master + PIC_IMR);
+	raw_spin_unlock_irqrestore(&sni_rm200_i8259A_lock, flags);
+}
+
+static void sni_rm200_enable_8259A_irq(struct irq_data *d)
+{
+	unsigned int mask, irq = d->irq - RM200_I8259A_IRQ_BASE;
+	unsigned long flags;
+
+	mask = ~(1 << irq);
+	raw_spin_lock_irqsave(&sni_rm200_i8259A_lock, flags);
+	rm200_cached_irq_mask &= mask;
+	if (irq & 8)
+		writeb(cached_slave_mask, rm200_pic_slave + PIC_IMR);
+	else
+		writeb(cached_master_mask, rm200_pic_master + PIC_IMR);
+	raw_spin_unlock_irqrestore(&sni_rm200_i8259A_lock, flags);
+}
+
+static inline int sni_rm200_i8259A_irq_real(unsigned int irq)
+{
+	int value;
+	int irqmask = 1 << irq;
+
+	if (irq < 8) {
+		writeb(0x0B, rm200_pic_master + PIC_CMD);
+		value = readb(rm200_pic_master + PIC_CMD) & irqmask;
+		writeb(0x0A, rm200_pic_master + PIC_CMD);
+		return value;
+	}
+	writeb(0x0B, rm200_pic_slave + PIC_CMD); /* ISR register */
+	value = readb(rm200_pic_slave + PIC_CMD) & (irqmask >> 8);
+	writeb(0x0A, rm200_pic_slave + PIC_CMD);
+	return value;
+}
+
+/*
+ * Careful! The 8259A is a fragile beast, it pretty
+ * much _has_ to be done exactly like this (mask it
+ * first, _then_ send the EOI, and the order of EOI
+ * to the two 8259s is important!
+ */
+void sni_rm200_mask_and_ack_8259A(struct irq_data *d)
+{
+	unsigned int irqmask, irq = d->irq - RM200_I8259A_IRQ_BASE;
+	unsigned long flags;
+
+	irqmask = 1 << irq;
+	raw_spin_lock_irqsave(&sni_rm200_i8259A_lock, flags);
+	/*
+	 * Lightweight spurious IRQ detection. We do not want
+	 * to overdo spurious IRQ handling - it's usually a sign
+	 * of hardware problems, so we only do the checks we can
+	 * do without slowing down good hardware unnecessarily.
+	 *
+	 * Note that IRQ7 and IRQ15 (the two spurious IRQs
+	 * usually resulting from the 8259A-1|2 PICs) occur
+	 * even if the IRQ is masked in the 8259A. Thus we
+	 * can check spurious 8259A IRQs without doing the
+	 * quite slow i8259A_irq_real() call for every IRQ.
+	 * This does not cover 100% of spurious interrupts,
+	 * but should be enough to warn the user that there
+	 * is something bad going on ...
+	 */
+	if (rm200_cached_irq_mask & irqmask)
+		goto spurious_8259A_irq;
+	rm200_cached_irq_mask |= irqmask;
+
+handle_real_irq:
+	if (irq & 8) {
+		readb(rm200_pic_slave + PIC_IMR);
+		writeb(cached_slave_mask, rm200_pic_slave + PIC_IMR);
+		writeb(0x60+(irq & 7), rm200_pic_slave + PIC_CMD);
+		writeb(0x60+PIC_CASCADE_IR, rm200_pic_master + PIC_CMD);
+	} else {
+		readb(rm200_pic_master + PIC_IMR);
+		writeb(cached_master_mask, rm200_pic_master + PIC_IMR);
+		writeb(0x60+irq, rm200_pic_master + PIC_CMD);
+	}
+	raw_spin_unlock_irqrestore(&sni_rm200_i8259A_lock, flags);
+	return;
+
+spurious_8259A_irq:
+	/*
+	 * this is the slow path - should happen rarely.
+	 */
+	if (sni_rm200_i8259A_irq_real(irq))
+		/*
+		 * oops, the IRQ _is_ in service according to the
+		 * 8259A - not spurious, go handle it.
+		 */
+		goto handle_real_irq;
+
+	{
+		static int spurious_irq_mask;
+		/*
+		 * At this point we can be sure the IRQ is spurious,
+		 * let's ACK and report it. [once per IRQ]
+		 */
+		if (!(spurious_irq_mask & irqmask)) {
+			printk(KERN_DEBUG
+			       "spurious RM200 8259A interrupt: IRQ%d.\n", irq);
+			spurious_irq_mask |= irqmask;
+		}
+		atomic_inc(&irq_err_count);
+		/*
+		 * Theoretically we do not have to handle this IRQ,
+		 * but in Linux this does not cause problems and is
+		 * simpler for us.
+		 */
+		goto handle_real_irq;
+	}
+}
+
+static struct irq_chip sni_rm200_i8259A_chip = {
+	.name		= "RM200-XT-PIC",
+	.irq_mask	= sni_rm200_disable_8259A_irq,
+	.irq_unmask	= sni_rm200_enable_8259A_irq,
+	.irq_mask_ack	= sni_rm200_mask_and_ack_8259A,
+};
+
+/*
+ * Do the traditional i8259 interrupt polling thing.  This is for the few
+ * cases where no better interrupt acknowledge method is available and we
+ * absolutely must touch the i8259.
+ */
+static inline int sni_rm200_i8259_irq(void)
+{
+	int irq;
+
+	raw_spin_lock(&sni_rm200_i8259A_lock);
+
+	/* Perform an interrupt acknowledge cycle on controller 1. */
+	writeb(0x0C, rm200_pic_master + PIC_CMD);	/* prepare for poll */
+	irq = readb(rm200_pic_master + PIC_CMD) & 7;
+	if (irq == PIC_CASCADE_IR) {
+		/*
+		 * Interrupt is cascaded so perform interrupt
+		 * acknowledge on controller 2.
+		 */
+		writeb(0x0C, rm200_pic_slave + PIC_CMD); /* prepare for poll */
+		irq = (readb(rm200_pic_slave + PIC_CMD) & 7) + 8;
+	}
+
+	if (unlikely(irq == 7)) {
+		/*
+		 * This may be a spurious interrupt.
+		 *
+		 * Read the interrupt status register (ISR). If the most
+		 * significant bit is not set then there is no valid
+		 * interrupt.
+		 */
+		writeb(0x0B, rm200_pic_master + PIC_ISR); /* ISR register */
+		if (~readb(rm200_pic_master + PIC_ISR) & 0x80)
+			irq = -1;
+	}
+
+	raw_spin_unlock(&sni_rm200_i8259A_lock);
+
+	return likely(irq >= 0) ? irq + RM200_I8259A_IRQ_BASE : irq;
+}
+
+void sni_rm200_init_8259A(void)
+{
+	unsigned long flags;
+
+	raw_spin_lock_irqsave(&sni_rm200_i8259A_lock, flags);
+
+	writeb(0xff, rm200_pic_master + PIC_IMR);
+	writeb(0xff, rm200_pic_slave + PIC_IMR);
+
+	writeb(0x11, rm200_pic_master + PIC_CMD);
+	writeb(0, rm200_pic_master + PIC_IMR);
+	writeb(1U << PIC_CASCADE_IR, rm200_pic_master + PIC_IMR);
+	writeb(MASTER_ICW4_DEFAULT, rm200_pic_master + PIC_IMR);
+	writeb(0x11, rm200_pic_slave + PIC_CMD);
+	writeb(8, rm200_pic_slave + PIC_IMR);
+	writeb(PIC_CASCADE_IR, rm200_pic_slave + PIC_IMR);
+	writeb(SLAVE_ICW4_DEFAULT, rm200_pic_slave + PIC_IMR);
+	udelay(100);		/* wait for 8259A to initialize */
+
+	writeb(cached_master_mask, rm200_pic_master + PIC_IMR);
+	writeb(cached_slave_mask, rm200_pic_slave + PIC_IMR);
+
+	raw_spin_unlock_irqrestore(&sni_rm200_i8259A_lock, flags);
+}
+
+/*
+ * IRQ2 is cascade interrupt to second interrupt controller
+ */
+
+static struct resource sni_rm200_pic1_resource = {
+	.name = "onboard ISA pic1",
+	.start = 0x16000020,
+	.end = 0x16000023,
+	.flags = IORESOURCE_BUSY
+};
+
+static struct resource sni_rm200_pic2_resource = {
+	.name = "onboard ISA pic2",
+	.start = 0x160000a0,
+	.end = 0x160000a3,
+	.flags = IORESOURCE_BUSY
+};
+
+/* ISA irq handler */
+static irqreturn_t sni_rm200_i8259A_irq_handler(int dummy, void *p)
+{
+	int irq;
+
+	irq = sni_rm200_i8259_irq();
+	if (unlikely(irq < 0))
+		return IRQ_NONE;
+
+	do_IRQ(irq);
+	return IRQ_HANDLED;
+}
+
+void __init sni_rm200_i8259_irqs(void)
+{
+	int i;
+
+	rm200_pic_master = ioremap(0x16000020, 4);
+	if (!rm200_pic_master)
+		return;
+	rm200_pic_slave = ioremap(0x160000a0, 4);
+	if (!rm200_pic_slave) {
+		iounmap(rm200_pic_master);
+		return;
+	}
+
+	insert_resource(&iomem_resource, &sni_rm200_pic1_resource);
+	insert_resource(&iomem_resource, &sni_rm200_pic2_resource);
+
+	sni_rm200_init_8259A();
+
+	for (i = RM200_I8259A_IRQ_BASE; i < RM200_I8259A_IRQ_BASE + 16; i++)
+		irq_set_chip_and_handler(i, &sni_rm200_i8259A_chip,
+					 handle_level_irq);
+
+	if (request_irq(RM200_I8259A_IRQ_BASE + PIC_CASCADE_IR, no_action,
+			IRQF_NO_THREAD, "cascade", NULL))
+		pr_err("Failed to register cascade interrupt\n");
+}
+
+
+#define SNI_RM200_INT_STAT_REG	CKSEG1ADDR(0xbc000000)
+#define SNI_RM200_INT_ENA_REG	CKSEG1ADDR(0xbc080000)
+
+#define SNI_RM200_INT_START  24
+#define SNI_RM200_INT_END    28
+
+static void enable_rm200_irq(struct irq_data *d)
+{
+	unsigned int mask = 1 << (d->irq - SNI_RM200_INT_START);
+
+	*(volatile u8 *)SNI_RM200_INT_ENA_REG &= ~mask;
+}
+
+void disable_rm200_irq(struct irq_data *d)
+{
+	unsigned int mask = 1 << (d->irq - SNI_RM200_INT_START);
+
+	*(volatile u8 *)SNI_RM200_INT_ENA_REG |= mask;
+}
+
+static struct irq_chip rm200_irq_type = {
+	.name = "RM200",
+	.irq_mask = disable_rm200_irq,
+	.irq_unmask = enable_rm200_irq,
+};
+
+static void sni_rm200_hwint(void)
+{
+	u32 pending = read_c0_cause() & read_c0_status();
+	u8 mask;
+	u8 stat;
+	int irq;
+
+	if (pending & C_IRQ5)
+		do_IRQ(MIPS_CPU_IRQ_BASE + 7);
+	else if (pending & C_IRQ0) {
+		clear_c0_status(IE_IRQ0);
+		mask = *(volatile u8 *)SNI_RM200_INT_ENA_REG ^ 0x1f;
+		stat = *(volatile u8 *)SNI_RM200_INT_STAT_REG ^ 0x14;
+		irq = ffs(stat & mask & 0x1f);
+
+		if (likely(irq > 0))
+			do_IRQ(irq + SNI_RM200_INT_START - 1);
+		set_c0_status(IE_IRQ0);
+	}
+}
+
+void __init sni_rm200_irq_init(void)
+{
+	int i;
+
+	* (volatile u8 *)SNI_RM200_INT_ENA_REG = 0x1f;
+
+	sni_rm200_i8259_irqs();
+	mips_cpu_irq_init();
+	/* Actually we've got more interrupts to handle ...  */
+	for (i = SNI_RM200_INT_START; i <= SNI_RM200_INT_END; i++)
+		irq_set_chip_and_handler(i, &rm200_irq_type, handle_level_irq);
+	sni_hwint = sni_rm200_hwint;
+	change_c0_status(ST0_IM, IE_IRQ0);
+	if (request_irq(SNI_RM200_INT_START + 0, sni_rm200_i8259A_irq_handler,
+			0, "onboard ISA", NULL))
+		pr_err("Failed to register onboard ISA interrupt\n");
+	if (request_irq(SNI_RM200_INT_START + 1, sni_isa_irq_handler, 0, "ISA",
+			NULL))
+		pr_err("Failed to register ISA interrupt\n");
+}
+
+void __init sni_rm200_init(void)
+{
+}
diff --git a/arch/mips/sni/setup.c b/arch/mips/sni/setup.c
new file mode 100644
index 000000000..efad85c8c
--- /dev/null
+++ b/arch/mips/sni/setup.c
@@ -0,0 +1,263 @@
+/*
+ * Setup pointers to hardware-dependent routines.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1996, 97, 98, 2000, 03, 04, 06 Ralf Baechle (ralf@linux-mips.org)
+ * Copyright (C) 2006,2007 Thomas Bogendoerfer (tsbogend@alpha.franken.de)
+ */
+#include <linux/eisa.h>
+#include <linux/init.h>
+#include <linux/export.h>
+#include <linux/console.h>
+#include <linux/fb.h>
+#include <linux/screen_info.h>
+
+#ifdef CONFIG_FW_ARC
+#include <asm/fw/arc/types.h>
+#include <asm/sgialib.h>
+#endif
+
+#ifdef CONFIG_FW_SNIPROM
+#include <asm/mipsprom.h>
+#endif
+
+#include <asm/bootinfo.h>
+#include <asm/cpu.h>
+#include <asm/io.h>
+#include <asm/reboot.h>
+#include <asm/sni.h>
+
+unsigned int sni_brd_type;
+EXPORT_SYMBOL(sni_brd_type);
+
+extern void sni_machine_restart(char *command);
+extern void sni_machine_power_off(void);
+
+static void __init sni_display_setup(void)
+{
+#if defined(CONFIG_VT) && defined(CONFIG_VGA_CONSOLE) && defined(CONFIG_FW_ARC)
+	struct screen_info *si = &screen_info;
+	DISPLAY_STATUS *di;
+
+	di = ArcGetDisplayStatus(1);
+
+	if (di) {
+		si->orig_x		= di->CursorXPosition;
+		si->orig_y		= di->CursorYPosition;
+		si->orig_video_cols	= di->CursorMaxXPosition;
+		si->orig_video_lines	= di->CursorMaxYPosition;
+		si->orig_video_isVGA	= VIDEO_TYPE_VGAC;
+		si->orig_video_points	= 16;
+	}
+#endif
+}
+
+static void __init sni_console_setup(void)
+{
+#ifndef CONFIG_FW_ARC
+	char *ctype;
+	char *cdev;
+	char *baud;
+	int port;
+	static char options[8] __initdata;
+
+	cdev = prom_getenv("console_dev");
+	if (strncmp(cdev, "tty", 3) == 0) {
+		ctype = prom_getenv("console");
+		switch (*ctype) {
+		default:
+		case 'l':
+			port = 0;
+			baud = prom_getenv("lbaud");
+			break;
+		case 'r':
+			port = 1;
+			baud = prom_getenv("rbaud");
+			break;
+		}
+		if (baud)
+			strcpy(options, baud);
+		if (strncmp(cdev, "tty552", 6) == 0)
+			add_preferred_console("ttyS", port,
+					      baud ? options : NULL);
+		else
+			add_preferred_console("ttySC", port,
+					      baud ? options : NULL);
+	}
+#endif
+}
+
+#ifdef DEBUG
+static void __init sni_idprom_dump(void)
+{
+	int	i;
+
+	pr_debug("SNI IDProm dump:\n");
+	for (i = 0; i < 256; i++) {
+		if (i%16 == 0)
+			pr_debug("%04x ", i);
+
+		printk("%02x ", *(unsigned char *) (SNI_IDPROM_BASE + i));
+
+		if (i % 16 == 15)
+			printk("\n");
+	}
+}
+#endif
+
+void __init plat_mem_setup(void)
+{
+	int cputype;
+
+	set_io_port_base(SNI_PORT_BASE);
+//	ioport_resource.end = sni_io_resource.end;
+
+	/*
+	 * Setup (E)ISA I/O memory access stuff
+	 */
+#ifdef CONFIG_EISA
+	EISA_bus = 1;
+#endif
+
+	sni_brd_type = *(unsigned char *)SNI_IDPROM_BRDTYPE;
+	cputype = *(unsigned char *)SNI_IDPROM_CPUTYPE;
+	switch (sni_brd_type) {
+	case SNI_BRD_TOWER_OASIC:
+		switch (cputype) {
+		case SNI_CPU_M8030:
+			system_type = "RM400-330";
+			break;
+		case SNI_CPU_M8031:
+			system_type = "RM400-430";
+			break;
+		case SNI_CPU_M8037:
+			system_type = "RM400-530";
+			break;
+		case SNI_CPU_M8034:
+			system_type = "RM400-730";
+			break;
+		default:
+			system_type = "RM400-xxx";
+			break;
+		}
+		break;
+	case SNI_BRD_MINITOWER:
+		switch (cputype) {
+		case SNI_CPU_M8021:
+		case SNI_CPU_M8043:
+			system_type = "RM400-120";
+			break;
+		case SNI_CPU_M8040:
+			system_type = "RM400-220";
+			break;
+		case SNI_CPU_M8053:
+			system_type = "RM400-225";
+			break;
+		case SNI_CPU_M8050:
+			system_type = "RM400-420";
+			break;
+		default:
+			system_type = "RM400-xxx";
+			break;
+		}
+		break;
+	case SNI_BRD_PCI_TOWER:
+		system_type = "RM400-Cxx";
+		break;
+	case SNI_BRD_RM200:
+		system_type = "RM200-xxx";
+		break;
+	case SNI_BRD_PCI_MTOWER:
+		system_type = "RM300-Cxx";
+		break;
+	case SNI_BRD_PCI_DESKTOP:
+		switch (read_c0_prid() & PRID_IMP_MASK) {
+		case PRID_IMP_R4600:
+		case PRID_IMP_R4700:
+			system_type = "RM200-C20";
+			break;
+		case PRID_IMP_R5000:
+			system_type = "RM200-C40";
+			break;
+		default:
+			system_type = "RM200-Cxx";
+			break;
+		}
+		break;
+	case SNI_BRD_PCI_TOWER_CPLUS:
+		system_type = "RM400-Exx";
+		break;
+	case SNI_BRD_PCI_MTOWER_CPLUS:
+		system_type = "RM300-Exx";
+		break;
+	}
+	pr_debug("Found SNI brdtype %02x name %s\n", sni_brd_type, system_type);
+
+#ifdef DEBUG
+	sni_idprom_dump();
+#endif
+
+	switch (sni_brd_type) {
+	case SNI_BRD_10:
+	case SNI_BRD_10NEW:
+	case SNI_BRD_TOWER_OASIC:
+	case SNI_BRD_MINITOWER:
+		sni_a20r_init();
+		break;
+
+	case SNI_BRD_PCI_TOWER:
+	case SNI_BRD_PCI_TOWER_CPLUS:
+		sni_pcit_init();
+		break;
+
+	case SNI_BRD_RM200:
+		sni_rm200_init();
+		break;
+
+	case SNI_BRD_PCI_MTOWER:
+	case SNI_BRD_PCI_DESKTOP:
+	case SNI_BRD_PCI_MTOWER_CPLUS:
+		sni_pcimt_init();
+		break;
+	}
+
+	_machine_restart = sni_machine_restart;
+	pm_power_off = sni_machine_power_off;
+
+	sni_display_setup();
+	sni_console_setup();
+}
+
+#ifdef CONFIG_PCI
+
+#include <linux/pci.h>
+#include <video/vga.h>
+#include <video/cirrus.h>
+
+static void quirk_cirrus_ram_size(struct pci_dev *dev)
+{
+	u16 cmd;
+
+	/*
+	 * firmware doesn't set the ram size correct, so we
+	 * need to do it here, otherwise we get screen corruption
+	 * on older Cirrus chips
+	 */
+	pci_read_config_word(dev, PCI_COMMAND, &cmd);
+	if ((cmd & (PCI_COMMAND_IO|PCI_COMMAND_MEMORY))
+		== (PCI_COMMAND_IO|PCI_COMMAND_MEMORY)) {
+		vga_wseq(NULL, CL_SEQR6, 0x12); /* unlock all extension registers */
+		vga_wseq(NULL, CL_SEQRF, 0x18);
+	}
+}
+
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_CIRRUS, PCI_DEVICE_ID_CIRRUS_5434_8,
+			quirk_cirrus_ram_size);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_CIRRUS, PCI_DEVICE_ID_CIRRUS_5436,
+			quirk_cirrus_ram_size);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_CIRRUS, PCI_DEVICE_ID_CIRRUS_5446,
+			quirk_cirrus_ram_size);
+#endif
diff --git a/arch/mips/sni/time.c b/arch/mips/sni/time.c
new file mode 100644
index 000000000..ff3ba7e77
--- /dev/null
+++ b/arch/mips/sni/time.c
@@ -0,0 +1,167 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/types.h>
+#include <linux/i8253.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/smp.h>
+#include <linux/time.h>
+#include <linux/clockchips.h>
+
+#include <asm/sni.h>
+#include <asm/time.h>
+
+#define SNI_CLOCK_TICK_RATE	3686400
+#define SNI_COUNTER2_DIV	64
+#define SNI_COUNTER0_DIV	((SNI_CLOCK_TICK_RATE / SNI_COUNTER2_DIV) / HZ)
+
+static int a20r_set_periodic(struct clock_event_device *evt)
+{
+	*(volatile u8 *)(A20R_PT_CLOCK_BASE + 12) = 0x34;
+	wmb();
+	*(volatile u8 *)(A20R_PT_CLOCK_BASE + 0) = SNI_COUNTER0_DIV & 0xff;
+	wmb();
+	*(volatile u8 *)(A20R_PT_CLOCK_BASE + 0) = SNI_COUNTER0_DIV >> 8;
+	wmb();
+
+	*(volatile u8 *)(A20R_PT_CLOCK_BASE + 12) = 0xb4;
+	wmb();
+	*(volatile u8 *)(A20R_PT_CLOCK_BASE + 8) = SNI_COUNTER2_DIV & 0xff;
+	wmb();
+	*(volatile u8 *)(A20R_PT_CLOCK_BASE + 8) = SNI_COUNTER2_DIV >> 8;
+	wmb();
+	return 0;
+}
+
+static struct clock_event_device a20r_clockevent_device = {
+	.name			= "a20r-timer",
+	.features		= CLOCK_EVT_FEAT_PERIODIC,
+
+	/* .mult, .shift, .max_delta_ns and .min_delta_ns left uninitialized */
+
+	.rating			= 300,
+	.irq			= SNI_A20R_IRQ_TIMER,
+	.set_state_periodic	= a20r_set_periodic,
+};
+
+static irqreturn_t a20r_interrupt(int irq, void *dev_id)
+{
+	struct clock_event_device *cd = dev_id;
+
+	*(volatile u8 *)A20R_PT_TIM0_ACK = 0;
+	wmb();
+
+	cd->event_handler(cd);
+
+	return IRQ_HANDLED;
+}
+
+/*
+ * a20r platform uses 2 counters to divide the input frequency.
+ * Counter 2 output is connected to Counter 0 & 1 input.
+ */
+static void __init sni_a20r_timer_setup(void)
+{
+	struct clock_event_device *cd = &a20r_clockevent_device;
+	unsigned int cpu = smp_processor_id();
+
+	cd->cpumask		= cpumask_of(cpu);
+	clockevents_register_device(cd);
+	if (request_irq(SNI_A20R_IRQ_TIMER, a20r_interrupt,
+			IRQF_PERCPU | IRQF_TIMER, "a20r-timer", cd))
+		pr_err("Failed to register a20r-timer interrupt\n");
+}
+
+#define SNI_8254_TICK_RATE	  1193182UL
+
+#define SNI_8254_TCSAMP_COUNTER	  ((SNI_8254_TICK_RATE / HZ) + 255)
+
+static __init unsigned long dosample(void)
+{
+	u32 ct0, ct1;
+	volatile u8 msb;
+
+	/* Start the counter. */
+	outb_p(0x34, 0x43);
+	outb_p(SNI_8254_TCSAMP_COUNTER & 0xff, 0x40);
+	outb(SNI_8254_TCSAMP_COUNTER >> 8, 0x40);
+
+	/* Get initial counter invariant */
+	ct0 = read_c0_count();
+
+	/* Latch and spin until top byte of counter0 is zero */
+	do {
+		outb(0x00, 0x43);
+		(void) inb(0x40);
+		msb = inb(0x40);
+		ct1 = read_c0_count();
+	} while (msb);
+
+	/* Stop the counter. */
+	outb(0x38, 0x43);
+	/*
+	 * Return the difference, this is how far the r4k counter increments
+	 * for every 1/HZ seconds. We round off the nearest 1 MHz of master
+	 * clock (= 1000000 / HZ / 2).
+	 */
+	/*return (ct1 - ct0 + (500000/HZ/2)) / (500000/HZ) * (500000/HZ);*/
+	return (ct1 - ct0) / (500000/HZ) * (500000/HZ);
+}
+
+/*
+ * Here we need to calibrate the cycle counter to at least be close.
+ */
+void __init plat_time_init(void)
+{
+	unsigned long r4k_ticks[3];
+	unsigned long r4k_tick;
+
+	/*
+	 * Figure out the r4k offset, the algorithm is very simple and works in
+	 * _all_ cases as long as the 8254 counter register itself works ok (as
+	 * an interrupt driving timer it does not because of bug, this is why
+	 * we are using the onchip r4k counter/compare register to serve this
+	 * purpose, but for r4k_offset calculation it will work ok for us).
+	 * There are other very complicated ways of performing this calculation
+	 * but this one works just fine so I am not going to futz around. ;-)
+	 */
+	printk(KERN_INFO "Calibrating system timer... ");
+	dosample();	/* Prime cache. */
+	dosample();	/* Prime cache. */
+	/* Zero is NOT an option. */
+	do {
+		r4k_ticks[0] = dosample();
+	} while (!r4k_ticks[0]);
+	do {
+		r4k_ticks[1] = dosample();
+	} while (!r4k_ticks[1]);
+
+	if (r4k_ticks[0] != r4k_ticks[1]) {
+		printk("warning: timer counts differ, retrying... ");
+		r4k_ticks[2] = dosample();
+		if (r4k_ticks[2] == r4k_ticks[0]
+		    || r4k_ticks[2] == r4k_ticks[1])
+			r4k_tick = r4k_ticks[2];
+		else {
+			printk("disagreement, using average... ");
+			r4k_tick = (r4k_ticks[0] + r4k_ticks[1]
+				   + r4k_ticks[2]) / 3;
+		}
+	} else
+		r4k_tick = r4k_ticks[0];
+
+	printk("%d [%d.%04d MHz CPU]\n", (int) r4k_tick,
+		(int) (r4k_tick / (500000 / HZ)),
+		(int) (r4k_tick % (500000 / HZ)));
+
+	mips_hpt_frequency = r4k_tick * HZ;
+
+	switch (sni_brd_type) {
+	case SNI_BRD_10:
+	case SNI_BRD_10NEW:
+	case SNI_BRD_TOWER_OASIC:
+	case SNI_BRD_MINITOWER:
+		sni_a20r_timer_setup();
+		break;
+	}
+	setup_pit_timer();
+}
diff --git a/arch/mips/tools/.gitignore b/arch/mips/tools/.gitignore
new file mode 100644
index 000000000..794817dfb
--- /dev/null
+++ b/arch/mips/tools/.gitignore
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0-only
+elf-entry
+loongson3-llsc-check
diff --git a/arch/mips/tools/Makefile b/arch/mips/tools/Makefile
new file mode 100644
index 000000000..b851e5dcc
--- /dev/null
+++ b/arch/mips/tools/Makefile
@@ -0,0 +1,10 @@
+# SPDX-License-Identifier: GPL-2.0
+hostprogs := elf-entry
+PHONY += elf-entry
+elf-entry: $(obj)/elf-entry
+	@:
+
+hostprogs += loongson3-llsc-check
+PHONY += loongson3-llsc-check
+loongson3-llsc-check: $(obj)/loongson3-llsc-check
+	@:
diff --git a/arch/mips/tools/elf-entry.c b/arch/mips/tools/elf-entry.c
new file mode 100644
index 000000000..dbd14ff05
--- /dev/null
+++ b/arch/mips/tools/elf-entry.c
@@ -0,0 +1,103 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <byteswap.h>
+#include <elf.h>
+#include <endian.h>
+#include <inttypes.h>
+#include <stdint.h>
+#include <stdio.h>
+#include <stdlib.h>
+#include <string.h>
+
+#ifdef be32toh
+/* If libc provides [bl]e{32,64}toh() then we'll use them */
+#elif BYTE_ORDER == LITTLE_ENDIAN
+# define be32toh(x)	bswap_32(x)
+# define le32toh(x)	(x)
+# define be64toh(x)	bswap_64(x)
+# define le64toh(x)	(x)
+#elif BYTE_ORDER == BIG_ENDIAN
+# define be32toh(x)	(x)
+# define le32toh(x)	bswap_32(x)
+# define be64toh(x)	(x)
+# define le64toh(x)	bswap_64(x)
+#endif
+
+__attribute__((noreturn))
+static void die(const char *msg)
+{
+	fputs(msg, stderr);
+	exit(EXIT_FAILURE);
+}
+
+int main(int argc, const char *argv[])
+{
+	uint64_t entry;
+	size_t nread;
+	FILE *file;
+	union {
+		Elf32_Ehdr ehdr32;
+		Elf64_Ehdr ehdr64;
+	} hdr;
+
+	if (argc != 2)
+		die("Usage: elf-entry <elf-file>\n");
+
+	file = fopen(argv[1], "r");
+	if (!file) {
+		perror("Unable to open input file");
+		return EXIT_FAILURE;
+	}
+
+	nread = fread(&hdr, 1, sizeof(hdr), file);
+	if (nread != sizeof(hdr)) {
+		perror("Unable to read input file");
+		fclose(file);
+		return EXIT_FAILURE;
+	}
+
+	if (memcmp(hdr.ehdr32.e_ident, ELFMAG, SELFMAG)) {
+		fclose(file);
+		die("Input is not an ELF\n");
+	}
+
+	switch (hdr.ehdr32.e_ident[EI_CLASS]) {
+	case ELFCLASS32:
+		switch (hdr.ehdr32.e_ident[EI_DATA]) {
+		case ELFDATA2LSB:
+			entry = le32toh(hdr.ehdr32.e_entry);
+			break;
+		case ELFDATA2MSB:
+			entry = be32toh(hdr.ehdr32.e_entry);
+			break;
+		default:
+			fclose(file);
+			die("Invalid ELF encoding\n");
+		}
+
+		/* Sign extend to form a canonical address */
+		entry = (int64_t)(int32_t)entry;
+		break;
+
+	case ELFCLASS64:
+		switch (hdr.ehdr32.e_ident[EI_DATA]) {
+		case ELFDATA2LSB:
+			entry = le64toh(hdr.ehdr64.e_entry);
+			break;
+		case ELFDATA2MSB:
+			entry = be64toh(hdr.ehdr64.e_entry);
+			break;
+		default:
+			fclose(file);
+			die("Invalid ELF encoding\n");
+		}
+		break;
+
+	default:
+		fclose(file);
+		die("Invalid ELF class\n");
+	}
+
+	printf("0x%016" PRIx64 "\n", entry);
+	fclose(file);
+	return EXIT_SUCCESS;
+}
diff --git a/arch/mips/tools/generic-board-config.sh b/arch/mips/tools/generic-board-config.sh
new file mode 100755
index 000000000..dfa5f31f5
--- /dev/null
+++ b/arch/mips/tools/generic-board-config.sh
@@ -0,0 +1,84 @@
+#!/bin/sh
+# SPDX-License-Identifier: GPL-2.0-or-later
+#
+# Copyright (C) 2017 Imagination Technologies
+# Author: Paul Burton <paul.burton@mips.com>
+#
+# This script merges configuration fragments for boards supported by the
+# generic MIPS kernel. It checks each for requirements specified using
+# formatted comments, and then calls merge_config.sh to merge those
+# fragments which have no unmet requirements.
+#
+# An example of requirements in your board config fragment might be:
+#
+# # require CONFIG_CPU_MIPS32_R2=y
+# # require CONFIG_CPU_LITTLE_ENDIAN=y
+#
+# This would mean that your board is only included in kernels which are
+# configured for little endian MIPS32r2 CPUs, and not for example in kernels
+# configured for 64 bit or big endian systems.
+#
+
+srctree="$1"
+objtree="$2"
+ref_cfg="$3"
+cfg="$4"
+boards_origin="$5"
+shift 5
+
+# Only print Skipping... lines if the user explicitly specified BOARDS=. In the
+# general case it only serves to obscure the useful output about what actually
+# was included.
+case ${boards_origin} in
+"command line")
+	print_skipped=1
+	;;
+environment*)
+	print_skipped=1
+	;;
+*)
+	print_skipped=0
+	;;
+esac
+
+for board in $@; do
+	board_cfg="${srctree}/arch/mips/configs/generic/board-${board}.config"
+	if [ ! -f "${board_cfg}" ]; then
+		echo "WARNING: Board config '${board_cfg}' not found"
+		continue
+	fi
+
+	# For each line beginning with # require, cut out the field following
+	# it & search for that in the reference config file. If the requirement
+	# is not found then the subshell will exit with code 1, and we'll
+	# continue on to the next board.
+	grep -E '^# require ' "${board_cfg}" | \
+	    cut -d' ' -f 3- | \
+	    while read req; do
+		case ${req} in
+		*=y)
+			# If we require something =y then we check that a line
+			# containing it is present in the reference config.
+			grep -Eq "^${req}\$" "${ref_cfg}" && continue
+			;;
+		*=n)
+			# If we require something =n then we just invert that
+			# check, considering the requirement met if there isn't
+			# a line containing the value =y in the reference
+			# config.
+			grep -Eq "^${req/%=n/=y}\$" "${ref_cfg}" || continue
+			;;
+		*)
+			echo "WARNING: Unhandled requirement '${req}'"
+			;;
+		esac
+
+		[ ${print_skipped} -eq 1 ] && echo "Skipping ${board_cfg}"
+		exit 1
+	done || continue
+
+	# Merge this board config fragment into our final config file
+	${srctree}/scripts/kconfig/merge_config.sh \
+		-m -O ${objtree} ${cfg} ${board_cfg} \
+		| grep -Ev '^(#|Using)'
+done
diff --git a/arch/mips/tools/loongson3-llsc-check.c b/arch/mips/tools/loongson3-llsc-check.c
new file mode 100644
index 000000000..5f68a4fa8
--- /dev/null
+++ b/arch/mips/tools/loongson3-llsc-check.c
@@ -0,0 +1,309 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include <byteswap.h>
+#include <elf.h>
+#include <endian.h>
+#include <errno.h>
+#include <fcntl.h>
+#include <inttypes.h>
+#include <stdbool.h>
+#include <stdio.h>
+#include <stdlib.h>
+#include <string.h>
+#include <sys/mman.h>
+#include <sys/types.h>
+#include <sys/stat.h>
+#include <unistd.h>
+
+#ifdef be32toh
+/* If libc provides le{16,32,64}toh() then we'll use them */
+#elif BYTE_ORDER == LITTLE_ENDIAN
+# define le16toh(x)	(x)
+# define le32toh(x)	(x)
+# define le64toh(x)	(x)
+#elif BYTE_ORDER == BIG_ENDIAN
+# define le16toh(x)	bswap_16(x)
+# define le32toh(x)	bswap_32(x)
+# define le64toh(x)	bswap_64(x)
+#endif
+
+/* MIPS opcodes, in bits 31:26 of an instruction */
+#define OP_SPECIAL	0x00
+#define OP_REGIMM	0x01
+#define OP_BEQ		0x04
+#define OP_BNE		0x05
+#define OP_BLEZ		0x06
+#define OP_BGTZ		0x07
+#define OP_BEQL		0x14
+#define OP_BNEL		0x15
+#define OP_BLEZL	0x16
+#define OP_BGTZL	0x17
+#define OP_LL		0x30
+#define OP_LLD		0x34
+#define OP_SC		0x38
+#define OP_SCD		0x3c
+
+/* Bits 20:16 of OP_REGIMM instructions */
+#define REGIMM_BLTZ	0x00
+#define REGIMM_BGEZ	0x01
+#define REGIMM_BLTZL	0x02
+#define REGIMM_BGEZL	0x03
+#define REGIMM_BLTZAL	0x10
+#define REGIMM_BGEZAL	0x11
+#define REGIMM_BLTZALL	0x12
+#define REGIMM_BGEZALL	0x13
+
+/* Bits 5:0 of OP_SPECIAL instructions */
+#define SPECIAL_SYNC	0x0f
+
+static void usage(FILE *f)
+{
+	fprintf(f, "Usage: loongson3-llsc-check /path/to/vmlinux\n");
+}
+
+static int se16(uint16_t x)
+{
+	return (int16_t)x;
+}
+
+static bool is_ll(uint32_t insn)
+{
+	switch (insn >> 26) {
+	case OP_LL:
+	case OP_LLD:
+		return true;
+
+	default:
+		return false;
+	}
+}
+
+static bool is_sc(uint32_t insn)
+{
+	switch (insn >> 26) {
+	case OP_SC:
+	case OP_SCD:
+		return true;
+
+	default:
+		return false;
+	}
+}
+
+static bool is_sync(uint32_t insn)
+{
+	/* Bits 31:11 should all be zeroes */
+	if (insn >> 11)
+		return false;
+
+	/* Bits 5:0 specify the SYNC special encoding */
+	if ((insn & 0x3f) != SPECIAL_SYNC)
+		return false;
+
+	return true;
+}
+
+static bool is_branch(uint32_t insn, int *off)
+{
+	switch (insn >> 26) {
+	case OP_BEQ:
+	case OP_BEQL:
+	case OP_BNE:
+	case OP_BNEL:
+	case OP_BGTZ:
+	case OP_BGTZL:
+	case OP_BLEZ:
+	case OP_BLEZL:
+		*off = se16(insn) + 1;
+		return true;
+
+	case OP_REGIMM:
+		switch ((insn >> 16) & 0x1f) {
+		case REGIMM_BGEZ:
+		case REGIMM_BGEZL:
+		case REGIMM_BGEZAL:
+		case REGIMM_BGEZALL:
+		case REGIMM_BLTZ:
+		case REGIMM_BLTZL:
+		case REGIMM_BLTZAL:
+		case REGIMM_BLTZALL:
+			*off = se16(insn) + 1;
+			return true;
+
+		default:
+			return false;
+		}
+
+	default:
+		return false;
+	}
+}
+
+static int check_ll(uint64_t pc, uint32_t *code, size_t sz)
+{
+	ssize_t i, max, sc_pos;
+	int off;
+
+	/*
+	 * Every LL must be preceded by a sync instruction in order to ensure
+	 * that instruction reordering doesn't allow a prior memory access to
+	 * execute after the LL & cause erroneous results.
+	 */
+	if (!is_sync(le32toh(code[-1]))) {
+		fprintf(stderr, "%" PRIx64 ": LL not preceded by sync\n", pc);
+		return -EINVAL;
+	}
+
+	/* Find the matching SC instruction */
+	max = sz / 4;
+	for (sc_pos = 0; sc_pos < max; sc_pos++) {
+		if (is_sc(le32toh(code[sc_pos])))
+			break;
+	}
+	if (sc_pos >= max) {
+		fprintf(stderr, "%" PRIx64 ": LL has no matching SC\n", pc);
+		return -EINVAL;
+	}
+
+	/*
+	 * Check branches within the LL/SC loop target sync instructions,
+	 * ensuring that speculative execution can't generate memory accesses
+	 * due to instructions outside of the loop.
+	 */
+	for (i = 0; i < sc_pos; i++) {
+		if (!is_branch(le32toh(code[i]), &off))
+			continue;
+
+		/*
+		 * If the branch target is within the LL/SC loop then we don't
+		 * need to worry about it.
+		 */
+		if ((off >= -i) && (off <= sc_pos))
+			continue;
+
+		/* If the branch targets a sync instruction we're all good... */
+		if (is_sync(le32toh(code[i + off])))
+			continue;
+
+		/* ...but if not, we have a problem */
+		fprintf(stderr, "%" PRIx64 ": Branch target not a sync\n",
+			pc + (i * 4));
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int check_code(uint64_t pc, uint32_t *code, size_t sz)
+{
+	int err = 0;
+
+	if (sz % 4) {
+		fprintf(stderr, "%" PRIx64 ": Section size not a multiple of 4\n",
+			pc);
+		err = -EINVAL;
+		sz -= (sz % 4);
+	}
+
+	if (is_ll(le32toh(code[0]))) {
+		fprintf(stderr, "%" PRIx64 ": First instruction in section is an LL\n",
+			pc);
+		err = -EINVAL;
+	}
+
+#define advance() (	\
+	code++,		\
+	pc += 4,	\
+	sz -= 4		\
+)
+
+	/*
+	 * Skip the first instruction, allowing check_ll to look backwards
+	 * unconditionally.
+	 */
+	advance();
+
+	/* Now scan through the code looking for LL instructions */
+	for (; sz; advance()) {
+		if (is_ll(le32toh(code[0])))
+			err |= check_ll(pc, code, sz);
+	}
+
+	return err;
+}
+
+int main(int argc, char *argv[])
+{
+	int vmlinux_fd, status, err, i;
+	const char *vmlinux_path;
+	struct stat st;
+	Elf64_Ehdr *eh;
+	Elf64_Shdr *sh;
+	void *vmlinux;
+
+	status = EXIT_FAILURE;
+
+	if (argc < 2) {
+		usage(stderr);
+		goto out_ret;
+	}
+
+	vmlinux_path = argv[1];
+	vmlinux_fd = open(vmlinux_path, O_RDONLY);
+	if (vmlinux_fd == -1) {
+		perror("Unable to open vmlinux");
+		goto out_ret;
+	}
+
+	err = fstat(vmlinux_fd, &st);
+	if (err) {
+		perror("Unable to stat vmlinux");
+		goto out_close;
+	}
+
+	vmlinux = mmap(NULL, st.st_size, PROT_READ, MAP_PRIVATE, vmlinux_fd, 0);
+	if (vmlinux == MAP_FAILED) {
+		perror("Unable to mmap vmlinux");
+		goto out_close;
+	}
+
+	eh = vmlinux;
+	if (memcmp(eh->e_ident, ELFMAG, SELFMAG)) {
+		fprintf(stderr, "vmlinux is not an ELF?\n");
+		goto out_munmap;
+	}
+
+	if (eh->e_ident[EI_CLASS] != ELFCLASS64) {
+		fprintf(stderr, "vmlinux is not 64b?\n");
+		goto out_munmap;
+	}
+
+	if (eh->e_ident[EI_DATA] != ELFDATA2LSB) {
+		fprintf(stderr, "vmlinux is not little endian?\n");
+		goto out_munmap;
+	}
+
+	for (i = 0; i < le16toh(eh->e_shnum); i++) {
+		sh = vmlinux + le64toh(eh->e_shoff) + (i * le16toh(eh->e_shentsize));
+
+		if (sh->sh_type != SHT_PROGBITS)
+			continue;
+		if (!(sh->sh_flags & SHF_EXECINSTR))
+			continue;
+
+		err = check_code(le64toh(sh->sh_addr),
+				 vmlinux + le64toh(sh->sh_offset),
+				 le64toh(sh->sh_size));
+		if (err)
+			goto out_munmap;
+	}
+
+	status = EXIT_SUCCESS;
+out_munmap:
+	munmap(vmlinux, st.st_size);
+out_close:
+	close(vmlinux_fd);
+out_ret:
+	fprintf(stdout, "loongson3-llsc-check returns %s\n",
+		status ? "failure" : "success");
+	return status;
+}
diff --git a/arch/mips/txx9/Kconfig b/arch/mips/txx9/Kconfig
new file mode 100644
index 000000000..7335efa4d
--- /dev/null
+++ b/arch/mips/txx9/Kconfig
@@ -0,0 +1,61 @@
+# SPDX-License-Identifier: GPL-2.0
+config MACH_TX49XX
+	bool
+	select BOOT_ELF32
+	select MACH_TXX9
+	select CEVT_R4K
+	select CSRC_R4K
+	select IRQ_MIPS_CPU
+	select SYS_HAS_CPU_TX49XX
+	select SYS_SUPPORTS_64BIT_KERNEL
+
+config MACH_TXX9
+	bool
+	select DMA_NONCOHERENT
+	select SWAP_IO_SPACE
+	select SYS_HAS_EARLY_PRINTK
+	select SYS_SUPPORTS_32BIT_KERNEL
+	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_SUPPORTS_BIG_ENDIAN
+	select COMMON_CLK
+
+config TOSHIBA_RBTX4927
+	bool "Toshiba RBTX49[23]7 board"
+	depends on MACH_TX49XX
+	select SOC_TX4927
+	# TX4937 is subset of TX4938
+	select SOC_TX4938
+	help
+	  This Toshiba board is based on the TX4927 processor. Say Y here to
+	  support this machine type
+
+config SOC_TX4927
+	bool
+	select CEVT_TXX9
+	imply HAS_TXX9_SERIAL
+	select HAVE_PCI
+	select IRQ_TXX9
+	select PCI_TX4927
+	select GPIO_TXX9
+
+config SOC_TX4938
+	bool
+	select CEVT_TXX9
+	imply HAS_TXX9_SERIAL
+	select HAVE_PCI
+	select IRQ_TXX9
+	select PCI_TX4927
+	select GPIO_TXX9
+
+config TOSHIBA_FPCIB0
+	bool "FPCIB0 Backplane Support"
+	depends on PCI && MACH_TXX9
+	select I8259
+
+config PICMG_PCI_BACKPLANE_DEFAULT
+	bool "Support for PICMG PCI Backplane"
+	depends on PCI && MACH_TXX9
+	default y if !TOSHIBA_FPCIB0
+
+config PCI_TX4927
+	bool
diff --git a/arch/mips/txx9/Makefile b/arch/mips/txx9/Makefile
new file mode 100644
index 000000000..14c91f267
--- /dev/null
+++ b/arch/mips/txx9/Makefile
@@ -0,0 +1,10 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Common TXx9
+#
+obj-$(CONFIG_MACH_TX49XX)      += generic/
+
+#
+# Toshiba RBTX49XX boards
+#
+obj-$(CONFIG_TOSHIBA_RBTX4927) += rbtx4927/
diff --git a/arch/mips/txx9/Platform b/arch/mips/txx9/Platform
new file mode 100644
index 000000000..e5a295068
--- /dev/null
+++ b/arch/mips/txx9/Platform
@@ -0,0 +1,4 @@
+cflags-$(CONFIG_MACH_TX49XX)	+=					\
+		 -I$(srctree)/arch/mips/include/asm/mach-tx49xx
+
+load-$(CONFIG_MACH_TX49XX)	+= 0xffffffff80100000
diff --git a/arch/mips/txx9/generic/Makefile b/arch/mips/txx9/generic/Makefile
new file mode 100644
index 000000000..3c155c7e2
--- /dev/null
+++ b/arch/mips/txx9/generic/Makefile
@@ -0,0 +1,10 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Makefile for common code for TXx9 based systems
+#
+
+obj-y	+= setup.o
+obj-$(CONFIG_PCI)	+= pci.o
+obj-$(CONFIG_SOC_TX4927)	+= mem_tx4927.o setup_tx4927.o irq_tx4927.o
+obj-$(CONFIG_SOC_TX4938)	+= mem_tx4927.o setup_tx4938.o irq_tx4938.o
+obj-$(CONFIG_TOSHIBA_FPCIB0)	+= smsc_fdc37m81x.o
diff --git a/arch/mips/txx9/generic/irq_tx4927.c b/arch/mips/txx9/generic/irq_tx4927.c
new file mode 100644
index 000000000..ed8e702d4
--- /dev/null
+++ b/arch/mips/txx9/generic/irq_tx4927.c
@@ -0,0 +1,49 @@
+/*
+ * Common tx4927 irq handler
+ *
+ * Author: MontaVista Software, Inc.
+ *	   source@mvista.com
+ *
+ *  under the terms of the GNU General Public License as published by the
+ *  Free Software Foundation; either version 2 of the License, or (at your
+ *  option) any later version.
+ *
+ *  THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ *  WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
+ *  IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ *  BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ *  OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ *  ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
+ *  TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
+ *  USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the GNU General Public License along
+ *  with this program; if not, write to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <asm/irq_cpu.h>
+#include <asm/txx9/tx4927.h>
+
+void __init tx4927_irq_init(void)
+{
+	int i;
+
+	mips_cpu_irq_init();
+	txx9_irq_init(TX4927_IRC_REG & 0xfffffffffULL);
+	irq_set_chained_handler(MIPS_CPU_IRQ_BASE + TX4927_IRC_INT,
+				handle_simple_irq);
+	/* raise priority for errors, timers, SIO */
+	txx9_irq_set_pri(TX4927_IR_ECCERR, 7);
+	txx9_irq_set_pri(TX4927_IR_WTOERR, 7);
+	txx9_irq_set_pri(TX4927_IR_PCIERR, 7);
+	txx9_irq_set_pri(TX4927_IR_PCIPME, 7);
+	for (i = 0; i < TX4927_NUM_IR_TMR; i++)
+		txx9_irq_set_pri(TX4927_IR_TMR(i), 6);
+	for (i = 0; i < TX4927_NUM_IR_SIO; i++)
+		txx9_irq_set_pri(TX4927_IR_SIO(i), 5);
+}
diff --git a/arch/mips/txx9/generic/irq_tx4938.c b/arch/mips/txx9/generic/irq_tx4938.c
new file mode 100644
index 000000000..aace85653
--- /dev/null
+++ b/arch/mips/txx9/generic/irq_tx4938.c
@@ -0,0 +1,37 @@
+/*
+ * linux/arch/mips/tx4938/common/irq.c
+ *
+ * Common tx4938 irq handler
+ * Copyright (C) 2000-2001 Toshiba Corporation
+ *
+ * 2003-2005 (c) MontaVista Software, Inc. This file is licensed under the
+ * terms of the GNU General Public License version 2. This program is
+ * licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ *
+ * Support for TX4938 in 2.6 - Manish Lachwani (mlachwani@mvista.com)
+ */
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <asm/irq_cpu.h>
+#include <asm/txx9/tx4938.h>
+
+void __init tx4938_irq_init(void)
+{
+	int i;
+
+	mips_cpu_irq_init();
+	txx9_irq_init(TX4938_IRC_REG & 0xfffffffffULL);
+	irq_set_chained_handler(MIPS_CPU_IRQ_BASE + TX4938_IRC_INT,
+				handle_simple_irq);
+	/* raise priority for errors, timers, SIO */
+	txx9_irq_set_pri(TX4938_IR_ECCERR, 7);
+	txx9_irq_set_pri(TX4938_IR_WTOERR, 7);
+	txx9_irq_set_pri(TX4938_IR_PCIERR, 7);
+	txx9_irq_set_pri(TX4938_IR_PCIPME, 7);
+	for (i = 0; i < TX4938_NUM_IR_TMR; i++)
+		txx9_irq_set_pri(TX4938_IR_TMR(i), 6);
+	for (i = 0; i < TX4938_NUM_IR_SIO; i++)
+		txx9_irq_set_pri(TX4938_IR_SIO(i), 5);
+}
diff --git a/arch/mips/txx9/generic/mem_tx4927.c b/arch/mips/txx9/generic/mem_tx4927.c
new file mode 100644
index 000000000..deea2ceae
--- /dev/null
+++ b/arch/mips/txx9/generic/mem_tx4927.c
@@ -0,0 +1,75 @@
+/*
+ * common tx4927 memory interface
+ *
+ * Author: MontaVista Software, Inc.
+ *	   source@mvista.com
+ *
+ * Copyright 2001-2002 MontaVista Software Inc.
+ *
+ *  This program is free software; you can redistribute it and/or modify it
+ *  under the terms of the GNU General Public License as published by the
+ *  Free Software Foundation; either version 2 of the License, or (at your
+ *  option) any later version.
+ *
+ *  THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ *  WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
+ *  IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ *  BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ *  OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ *  ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
+ *  TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
+ *  USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the GNU General Public License along
+ *  with this program; if not, write to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/io.h>
+#include <asm/txx9/tx4927.h>
+
+static unsigned int __init tx4927_process_sdccr(u64 __iomem *addr)
+{
+	u64 val;
+	unsigned int sdccr_ce;
+	unsigned int sdccr_bs;
+	unsigned int sdccr_rs;
+	unsigned int sdccr_cs;
+	unsigned int sdccr_mw;
+	unsigned int bs = 0;
+	unsigned int rs = 0;
+	unsigned int cs = 0;
+	unsigned int mw = 0;
+
+	val = __raw_readq(addr);
+
+	/* MVMCP -- need #defs for these bits masks */
+	sdccr_ce = ((val & (1 << 10)) >> 10);
+	sdccr_bs = ((val & (1 << 8)) >> 8);
+	sdccr_rs = ((val & (3 << 5)) >> 5);
+	sdccr_cs = ((val & (7 << 2)) >> 2);
+	sdccr_mw = ((val & (1 << 0)) >> 0);
+
+	if (sdccr_ce) {
+		bs = 2 << sdccr_bs;
+		rs = 2048 << sdccr_rs;
+		cs = 256 << sdccr_cs;
+		mw = 8 >> sdccr_mw;
+	}
+
+	return rs * cs * mw * bs;
+}
+
+unsigned int __init tx4927_get_mem_size(void)
+{
+	unsigned int total = 0;
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(tx4927_sdramcptr->cr); i++)
+		total += tx4927_process_sdccr(&tx4927_sdramcptr->cr[i]);
+	return total;
+}
diff --git a/arch/mips/txx9/generic/pci.c b/arch/mips/txx9/generic/pci.c
new file mode 100644
index 000000000..e98845543
--- /dev/null
+++ b/arch/mips/txx9/generic/pci.c
@@ -0,0 +1,432 @@
+/*
+ * linux/arch/mips/txx9/pci.c
+ *
+ * Based on linux/arch/mips/txx9/rbtx4927/setup.c,
+ *	    linux/arch/mips/txx9/rbtx4938/setup.c,
+ *	    and RBTX49xx patch from CELF patch archive.
+ *
+ * Copyright 2001-2005 MontaVista Software Inc.
+ * Copyright (C) 1996, 97, 2001, 04  Ralf Baechle (ralf@linux-mips.org)
+ * (C) Copyright TOSHIBA CORPORATION 2000-2001, 2004-2007
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#include <linux/delay.h>
+#include <linux/jiffies.h>
+#include <linux/io.h>
+#include <asm/txx9/generic.h>
+#include <asm/txx9/pci.h>
+#ifdef CONFIG_TOSHIBA_FPCIB0
+#include <linux/interrupt.h>
+#include <linux/slab.h>
+#include <asm/i8259.h>
+#include <asm/txx9/smsc_fdc37m81x.h>
+#endif
+
+static int __init
+early_read_config_word(struct pci_controller *hose,
+		       int top_bus, int bus, int devfn, int offset, u16 *value)
+{
+	struct pci_bus fake_bus;
+
+	fake_bus.number = bus;
+	fake_bus.sysdata = hose;
+	fake_bus.ops = hose->pci_ops;
+
+	if (bus != top_bus)
+		/* Fake a parent bus structure. */
+		fake_bus.parent = &fake_bus;
+	else
+		fake_bus.parent = NULL;
+
+	return pci_bus_read_config_word(&fake_bus, devfn, offset, value);
+}
+
+int __init txx9_pci66_check(struct pci_controller *hose, int top_bus,
+			    int current_bus)
+{
+	u32 pci_devfn;
+	unsigned short vid;
+	int cap66 = -1;
+	u16 stat;
+
+	/* It seems SLC90E66 needs some time after PCI reset... */
+	mdelay(80);
+
+	pr_info("PCI: Checking 66MHz capabilities...\n");
+
+	for (pci_devfn = 0; pci_devfn < 0xff; pci_devfn++) {
+		if (PCI_FUNC(pci_devfn))
+			continue;
+		if (early_read_config_word(hose, top_bus, current_bus,
+					   pci_devfn, PCI_VENDOR_ID, &vid) !=
+		    PCIBIOS_SUCCESSFUL)
+			continue;
+		if (vid == 0xffff)
+			continue;
+
+		/* check 66MHz capability */
+		if (cap66 < 0)
+			cap66 = 1;
+		if (cap66) {
+			early_read_config_word(hose, top_bus, current_bus,
+					       pci_devfn, PCI_STATUS, &stat);
+			if (!(stat & PCI_STATUS_66MHZ)) {
+				pr_debug("PCI: %02x:%02x not 66MHz capable.\n",
+					 current_bus, pci_devfn);
+				cap66 = 0;
+				break;
+			}
+		}
+	}
+	return cap66 > 0;
+}
+
+static struct resource primary_pci_mem_res[2] = {
+	{ .name = "PCI MEM" },
+	{ .name = "PCI MMIO" },
+};
+static struct resource primary_pci_io_res = { .name = "PCI IO" };
+struct pci_controller txx9_primary_pcic = {
+	.mem_resource = &primary_pci_mem_res[0],
+	.io_resource = &primary_pci_io_res,
+};
+
+#ifdef CONFIG_64BIT
+int txx9_pci_mem_high __initdata = 1;
+#else
+int txx9_pci_mem_high __initdata;
+#endif
+
+/*
+ * allocate pci_controller and resources.
+ * mem_base, io_base: physical address.	 0 for auto assignment.
+ * mem_size and io_size means max size on auto assignment.
+ * pcic must be &txx9_primary_pcic or NULL.
+ */
+struct pci_controller *__init
+txx9_alloc_pci_controller(struct pci_controller *pcic,
+			  unsigned long mem_base, unsigned long mem_size,
+			  unsigned long io_base, unsigned long io_size)
+{
+	struct pcic {
+		struct pci_controller c;
+		struct resource r_mem[2];
+		struct resource r_io;
+	} *new = NULL;
+	int min_size = 0x10000;
+
+	if (!pcic) {
+		new = kzalloc(sizeof(*new), GFP_KERNEL);
+		if (!new)
+			return NULL;
+		new->r_mem[0].name = "PCI mem";
+		new->r_mem[1].name = "PCI mmio";
+		new->r_io.name = "PCI io";
+		new->c.mem_resource = new->r_mem;
+		new->c.io_resource = &new->r_io;
+		pcic = &new->c;
+	} else
+		BUG_ON(pcic != &txx9_primary_pcic);
+	pcic->io_resource->flags = IORESOURCE_IO;
+
+	/*
+	 * for auto assignment, first search a (big) region for PCI
+	 * MEM, then search a region for PCI IO.
+	 */
+	if (mem_base) {
+		pcic->mem_resource[0].start = mem_base;
+		pcic->mem_resource[0].end = mem_base + mem_size - 1;
+		if (request_resource(&iomem_resource, &pcic->mem_resource[0]))
+			goto free_and_exit;
+	} else {
+		unsigned long min = 0, max = 0x20000000; /* low 512MB */
+		if (!mem_size) {
+			/* default size for auto assignment */
+			if (txx9_pci_mem_high)
+				mem_size = 0x20000000;	/* mem:512M(max) */
+			else
+				mem_size = 0x08000000;	/* mem:128M(max) */
+		}
+		if (txx9_pci_mem_high) {
+			min = 0x20000000;
+			max = 0xe0000000;
+		}
+		/* search free region for PCI MEM */
+		for (; mem_size >= min_size; mem_size /= 2) {
+			if (allocate_resource(&iomem_resource,
+					      &pcic->mem_resource[0],
+					      mem_size, min, max,
+					      mem_size, NULL, NULL) == 0)
+				break;
+		}
+		if (mem_size < min_size)
+			goto free_and_exit;
+	}
+
+	pcic->mem_resource[1].flags = IORESOURCE_MEM | IORESOURCE_BUSY;
+	if (io_base) {
+		pcic->mem_resource[1].start = io_base;
+		pcic->mem_resource[1].end = io_base + io_size - 1;
+		if (request_resource(&iomem_resource, &pcic->mem_resource[1]))
+			goto release_and_exit;
+	} else {
+		if (!io_size)
+			/* default size for auto assignment */
+			io_size = 0x01000000;	/* io:16M(max) */
+		/* search free region for PCI IO in low 512MB */
+		for (; io_size >= min_size; io_size /= 2) {
+			if (allocate_resource(&iomem_resource,
+					      &pcic->mem_resource[1],
+					      io_size, 0, 0x20000000,
+					      io_size, NULL, NULL) == 0)
+				break;
+		}
+		if (io_size < min_size)
+			goto release_and_exit;
+		io_base = pcic->mem_resource[1].start;
+	}
+
+	pcic->mem_resource[0].flags = IORESOURCE_MEM;
+	if (pcic == &txx9_primary_pcic &&
+	    mips_io_port_base == (unsigned long)-1) {
+		/* map ioport 0 to PCI I/O space address 0 */
+		set_io_port_base(IO_BASE + pcic->mem_resource[1].start);
+		pcic->io_resource->start = 0;
+		pcic->io_offset = 0;	/* busaddr == ioaddr */
+		pcic->io_map_base = IO_BASE + pcic->mem_resource[1].start;
+	} else {
+		/* physaddr to ioaddr */
+		pcic->io_resource->start =
+			io_base - (mips_io_port_base - IO_BASE);
+		pcic->io_offset = io_base - (mips_io_port_base - IO_BASE);
+		pcic->io_map_base = mips_io_port_base;
+	}
+	pcic->io_resource->end = pcic->io_resource->start + io_size - 1;
+
+	pcic->mem_offset = 0;	/* busaddr == physaddr */
+
+	pr_info("PCI: IO %pR MEM %pR\n", &pcic->mem_resource[1],
+		&pcic->mem_resource[0]);
+
+	/* register_pci_controller() will request MEM resource */
+	release_resource(&pcic->mem_resource[0]);
+	return pcic;
+ release_and_exit:
+	release_resource(&pcic->mem_resource[0]);
+ free_and_exit:
+	kfree(new);
+	pr_err("PCI: Failed to allocate resources.\n");
+	return NULL;
+}
+
+static int __init
+txx9_arch_pci_init(void)
+{
+	PCIBIOS_MIN_IO = 0x8000;	/* reserve legacy I/O space */
+	return 0;
+}
+arch_initcall(txx9_arch_pci_init);
+
+/* IRQ/IDSEL mapping */
+int txx9_pci_option =
+#ifdef CONFIG_PICMG_PCI_BACKPLANE_DEFAULT
+	TXX9_PCI_OPT_PICMG |
+#endif
+	TXX9_PCI_OPT_CLK_AUTO;
+
+enum txx9_pci_err_action txx9_pci_err_action = TXX9_PCI_ERR_REPORT;
+
+#ifdef CONFIG_TOSHIBA_FPCIB0
+static irqreturn_t i8259_interrupt(int irq, void *dev_id)
+{
+	int isairq;
+
+	isairq = i8259_irq();
+	if (unlikely(isairq <= I8259A_IRQ_BASE))
+		return IRQ_NONE;
+	generic_handle_irq(isairq);
+	return IRQ_HANDLED;
+}
+
+static int txx9_i8259_irq_setup(int irq)
+{
+	int err;
+
+	init_i8259_irqs();
+	err = request_irq(irq, &i8259_interrupt, IRQF_SHARED,
+			  "cascade(i8259)", (void *)(long)irq);
+	if (!err)
+		pr_info("PCI-ISA bridge PIC (irq %d)\n", irq);
+	return err;
+}
+
+static void __ref quirk_slc90e66_bridge(struct pci_dev *dev)
+{
+	int irq;	/* PCI/ISA Bridge interrupt */
+	u8 reg_64;
+	u32 reg_b0;
+	u8 reg_e1;
+	irq = pcibios_map_irq(dev, PCI_SLOT(dev->devfn), 1); /* INTA */
+	if (!irq)
+		return;
+	txx9_i8259_irq_setup(irq);
+	pci_read_config_byte(dev, 0x64, &reg_64);
+	pci_read_config_dword(dev, 0xb0, &reg_b0);
+	pci_read_config_byte(dev, 0xe1, &reg_e1);
+	/* serial irq control */
+	reg_64 = 0xd0;
+	/* serial irq pin */
+	reg_b0 |= 0x00010000;
+	/* ide irq on isa14 */
+	reg_e1 &= 0xf0;
+	reg_e1 |= 0x0d;
+	pci_write_config_byte(dev, 0x64, reg_64);
+	pci_write_config_dword(dev, 0xb0, reg_b0);
+	pci_write_config_byte(dev, 0xe1, reg_e1);
+
+	smsc_fdc37m81x_init(0x3f0);
+	smsc_fdc37m81x_config_beg();
+	smsc_fdc37m81x_config_set(SMSC_FDC37M81X_DNUM,
+				  SMSC_FDC37M81X_KBD);
+	smsc_fdc37m81x_config_set(SMSC_FDC37M81X_INT, 1);
+	smsc_fdc37m81x_config_set(SMSC_FDC37M81X_INT2, 12);
+	smsc_fdc37m81x_config_set(SMSC_FDC37M81X_ACTIVE,
+				  1);
+	smsc_fdc37m81x_config_end();
+}
+
+static void quirk_slc90e66_ide(struct pci_dev *dev)
+{
+	unsigned char dat;
+	int regs[2] = {0x41, 0x43};
+	int i;
+
+	/* SMSC SLC90E66 IDE uses irq 14, 15 (default) */
+	pci_write_config_byte(dev, PCI_INTERRUPT_LINE, 14);
+	pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &dat);
+	pr_info("PCI: %s: IRQ %02x", pci_name(dev), dat);
+	/* enable SMSC SLC90E66 IDE */
+	for (i = 0; i < ARRAY_SIZE(regs); i++) {
+		pci_read_config_byte(dev, regs[i], &dat);
+		pci_write_config_byte(dev, regs[i], dat | 0x80);
+		pci_read_config_byte(dev, regs[i], &dat);
+		pr_cont(" IDETIM%d %02x", i, dat);
+	}
+	pci_read_config_byte(dev, 0x5c, &dat);
+	/*
+	 * !!! DO NOT REMOVE THIS COMMENT IT IS REQUIRED BY SMSC !!!
+	 *
+	 * This line of code is intended to provide the user with a work
+	 * around solution to the anomalies cited in SMSC's anomaly sheet
+	 * entitled, "SLC90E66 Functional Rev.J_0.1 Anomalies"".
+	 *
+	 * !!! DO NOT REMOVE THIS COMMENT IT IS REQUIRED BY SMSC !!!
+	 */
+	dat |= 0x01;
+	pci_write_config_byte(dev, 0x5c, dat);
+	pci_read_config_byte(dev, 0x5c, &dat);
+	pr_cont(" REG5C %02x\n", dat);
+}
+#endif /* CONFIG_TOSHIBA_FPCIB0 */
+
+static void tc35815_fixup(struct pci_dev *dev)
+{
+	/* This device may have PM registers but not they are not supported. */
+	if (dev->pm_cap) {
+		dev_info(&dev->dev, "PM disabled\n");
+		dev->pm_cap = 0;
+	}
+}
+
+static void final_fixup(struct pci_dev *dev)
+{
+	unsigned char bist;
+
+	/* Do build-in self test */
+	if (pci_read_config_byte(dev, PCI_BIST, &bist) == PCIBIOS_SUCCESSFUL &&
+	    (bist & PCI_BIST_CAPABLE)) {
+		unsigned long timeout;
+		pci_set_power_state(dev, PCI_D0);
+		pr_info("PCI: %s BIST...", pci_name(dev));
+		pci_write_config_byte(dev, PCI_BIST, PCI_BIST_START);
+		timeout = jiffies + HZ * 2;	/* timeout after 2 sec */
+		do {
+			pci_read_config_byte(dev, PCI_BIST, &bist);
+			if (time_after(jiffies, timeout))
+				break;
+		} while (bist & PCI_BIST_START);
+		if (bist & (PCI_BIST_CODE_MASK | PCI_BIST_START))
+			pr_cont("failed. (0x%x)\n", bist);
+		else
+			pr_cont("OK.\n");
+	}
+}
+
+#ifdef CONFIG_TOSHIBA_FPCIB0
+#define PCI_DEVICE_ID_EFAR_SLC90E66_0 0x9460
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_EFAR, PCI_DEVICE_ID_EFAR_SLC90E66_0,
+	quirk_slc90e66_bridge);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_EFAR, PCI_DEVICE_ID_EFAR_SLC90E66_1,
+	quirk_slc90e66_ide);
+DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_EFAR, PCI_DEVICE_ID_EFAR_SLC90E66_1,
+	quirk_slc90e66_ide);
+#endif
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_TOSHIBA_2,
+			PCI_DEVICE_ID_TOSHIBA_TC35815_NWU, tc35815_fixup);
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_TOSHIBA_2,
+			PCI_DEVICE_ID_TOSHIBA_TC35815_TX4939, tc35815_fixup);
+DECLARE_PCI_FIXUP_FINAL(PCI_ANY_ID, PCI_ANY_ID, final_fixup);
+DECLARE_PCI_FIXUP_RESUME(PCI_ANY_ID, PCI_ANY_ID, final_fixup);
+
+int pcibios_plat_dev_init(struct pci_dev *dev)
+{
+	return 0;
+}
+
+static int (*txx9_pci_map_irq)(const struct pci_dev *dev, u8 slot, u8 pin);
+int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	return txx9_pci_map_irq(dev, slot, pin);
+}
+
+char * (*txx9_board_pcibios_setup)(char *str) __initdata;
+
+char *__init txx9_pcibios_setup(char *str)
+{
+	if (txx9_board_pcibios_setup && !txx9_board_pcibios_setup(str))
+		return NULL;
+	if (!strcmp(str, "picmg")) {
+		/* PICMG compliant backplane (TOSHIBA JMB-PICMG-ATX
+		   (5V or 3.3V), JMB-PICMG-L2 (5V only), etc.) */
+		txx9_pci_option |= TXX9_PCI_OPT_PICMG;
+		return NULL;
+	} else if (!strcmp(str, "nopicmg")) {
+		/* non-PICMG compliant backplane (TOSHIBA
+		   RBHBK4100,RBHBK4200, Interface PCM-PCM05, etc.) */
+		txx9_pci_option &= ~TXX9_PCI_OPT_PICMG;
+		return NULL;
+	} else if (!strncmp(str, "clk=", 4)) {
+		char *val = str + 4;
+		txx9_pci_option &= ~TXX9_PCI_OPT_CLK_MASK;
+		if (strcmp(val, "33") == 0)
+			txx9_pci_option |= TXX9_PCI_OPT_CLK_33;
+		else if (strcmp(val, "66") == 0)
+			txx9_pci_option |= TXX9_PCI_OPT_CLK_66;
+		else /* "auto" */
+			txx9_pci_option |= TXX9_PCI_OPT_CLK_AUTO;
+		return NULL;
+	} else if (!strncmp(str, "err=", 4)) {
+		if (!strcmp(str + 4, "panic"))
+			txx9_pci_err_action = TXX9_PCI_ERR_PANIC;
+		else if (!strcmp(str + 4, "ignore"))
+			txx9_pci_err_action = TXX9_PCI_ERR_IGNORE;
+		return NULL;
+	}
+
+	txx9_pci_map_irq = txx9_board_vec->pci_map_irq;
+
+	return str;
+}
diff --git a/arch/mips/txx9/generic/setup.c b/arch/mips/txx9/generic/setup.c
new file mode 100644
index 000000000..b098a3c76
--- /dev/null
+++ b/arch/mips/txx9/generic/setup.c
@@ -0,0 +1,853 @@
+/*
+ * Based on linux/arch/mips/txx9/rbtx4938/setup.c,
+ *	    and RBTX49xx patch from CELF patch archive.
+ *
+ * 2003-2005 (c) MontaVista Software, Inc.
+ * (C) Copyright TOSHIBA CORPORATION 2000-2001, 2004-2007
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/string.h>
+#include <linux/export.h>
+#include <linux/clk-provider.h>
+#include <linux/clkdev.h>
+#include <linux/err.h>
+#include <linux/gpio/driver.h>
+#include <linux/platform_device.h>
+#include <linux/platform_data/txx9/ndfmc.h>
+#include <linux/serial_core.h>
+#include <linux/mtd/physmap.h>
+#include <linux/leds.h>
+#include <linux/device.h>
+#include <linux/slab.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <asm/bootinfo.h>
+#include <asm/idle.h>
+#include <asm/time.h>
+#include <asm/reboot.h>
+#include <asm/r4kcache.h>
+#include <asm/setup.h>
+#include <asm/txx9/generic.h>
+#include <asm/txx9/pci.h>
+#include <asm/txx9tmr.h>
+#include <asm/txx9/dmac.h>
+#ifdef CONFIG_CPU_TX49XX
+#include <asm/txx9/tx4938.h>
+#endif
+
+/* EBUSC settings of TX4927, etc. */
+struct resource txx9_ce_res[8];
+static char txx9_ce_res_name[8][4];	/* "CEn" */
+
+/* pcode, internal register */
+unsigned int txx9_pcode;
+char txx9_pcode_str[8];
+static struct resource txx9_reg_res = {
+	.name = txx9_pcode_str,
+	.flags = IORESOURCE_MEM,
+};
+void __init
+txx9_reg_res_init(unsigned int pcode, unsigned long base, unsigned long size)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(txx9_ce_res); i++) {
+		sprintf(txx9_ce_res_name[i], "CE%d", i);
+		txx9_ce_res[i].flags = IORESOURCE_MEM;
+		txx9_ce_res[i].name = txx9_ce_res_name[i];
+	}
+
+	txx9_pcode = pcode;
+	sprintf(txx9_pcode_str, "TX%x", pcode);
+	if (base) {
+		txx9_reg_res.start = base & 0xfffffffffULL;
+		txx9_reg_res.end = (base & 0xfffffffffULL) + (size - 1);
+		request_resource(&iomem_resource, &txx9_reg_res);
+	}
+}
+
+/* clocks */
+unsigned int txx9_master_clock;
+unsigned int txx9_cpu_clock;
+unsigned int txx9_gbus_clock;
+
+int txx9_ccfg_toeon __initdata = 1;
+
+#define BOARD_VEC(board)	extern struct txx9_board_vec board;
+#include <asm/txx9/boards.h>
+#undef BOARD_VEC
+
+struct txx9_board_vec *txx9_board_vec __initdata;
+static char txx9_system_type[32];
+
+static struct txx9_board_vec *board_vecs[] __initdata = {
+#define BOARD_VEC(board)	&board,
+#include <asm/txx9/boards.h>
+#undef BOARD_VEC
+};
+
+static struct txx9_board_vec *__init find_board_byname(const char *name)
+{
+	int i;
+
+	/* search board_vecs table */
+	for (i = 0; i < ARRAY_SIZE(board_vecs); i++) {
+		if (strstr(board_vecs[i]->system, name))
+			return board_vecs[i];
+	}
+	return NULL;
+}
+
+static void __init prom_init_cmdline(void)
+{
+	int argc;
+	int *argv32;
+	int i;			/* Always ignore the "-c" at argv[0] */
+
+	if (fw_arg0 >= CKSEG0 || fw_arg1 < CKSEG0) {
+		/*
+		 * argc is not a valid number, or argv32 is not a valid
+		 * pointer
+		 */
+		argc = 0;
+		argv32 = NULL;
+	} else {
+		argc = (int)fw_arg0;
+		argv32 = (int *)fw_arg1;
+	}
+
+	arcs_cmdline[0] = '\0';
+
+	for (i = 1; i < argc; i++) {
+		char *str = (char *)(long)argv32[i];
+		if (i != 1)
+			strcat(arcs_cmdline, " ");
+		if (strchr(str, ' ')) {
+			strcat(arcs_cmdline, "\"");
+			strcat(arcs_cmdline, str);
+			strcat(arcs_cmdline, "\"");
+		} else
+			strcat(arcs_cmdline, str);
+	}
+}
+
+static int txx9_ic_disable __initdata;
+static int txx9_dc_disable __initdata;
+
+#if defined(CONFIG_CPU_TX49XX)
+/* flush all cache on very early stage (before 4k_cache_init) */
+static void __init early_flush_dcache(void)
+{
+	unsigned int conf = read_c0_config();
+	unsigned int dc_size = 1 << (12 + ((conf & CONF_DC) >> 6));
+	unsigned int linesz = 32;
+	unsigned long addr, end;
+
+	end = INDEX_BASE + dc_size / 4;
+	/* 4way, waybit=0 */
+	for (addr = INDEX_BASE; addr < end; addr += linesz) {
+		cache_op(Index_Writeback_Inv_D, addr | 0);
+		cache_op(Index_Writeback_Inv_D, addr | 1);
+		cache_op(Index_Writeback_Inv_D, addr | 2);
+		cache_op(Index_Writeback_Inv_D, addr | 3);
+	}
+}
+
+static void __init txx9_cache_fixup(void)
+{
+	unsigned int conf;
+
+	conf = read_c0_config();
+	/* flush and disable */
+	if (txx9_ic_disable) {
+		conf |= TX49_CONF_IC;
+		write_c0_config(conf);
+	}
+	if (txx9_dc_disable) {
+		early_flush_dcache();
+		conf |= TX49_CONF_DC;
+		write_c0_config(conf);
+	}
+
+	/* enable cache */
+	conf = read_c0_config();
+	if (!txx9_ic_disable)
+		conf &= ~TX49_CONF_IC;
+	if (!txx9_dc_disable)
+		conf &= ~TX49_CONF_DC;
+	write_c0_config(conf);
+
+	if (conf & TX49_CONF_IC)
+		pr_info("TX49XX I-Cache disabled.\n");
+	if (conf & TX49_CONF_DC)
+		pr_info("TX49XX D-Cache disabled.\n");
+}
+#else
+static inline void txx9_cache_fixup(void)
+{
+}
+#endif
+
+static void __init preprocess_cmdline(void)
+{
+	static char cmdline[COMMAND_LINE_SIZE] __initdata;
+	char *s;
+
+	strcpy(cmdline, arcs_cmdline);
+	s = cmdline;
+	arcs_cmdline[0] = '\0';
+	while (s && *s) {
+		char *str = strsep(&s, " ");
+		if (strncmp(str, "board=", 6) == 0) {
+			txx9_board_vec = find_board_byname(str + 6);
+			continue;
+		} else if (strncmp(str, "masterclk=", 10) == 0) {
+			unsigned int val;
+			if (kstrtouint(str + 10, 10, &val) == 0)
+				txx9_master_clock = val;
+			continue;
+		} else if (strcmp(str, "icdisable") == 0) {
+			txx9_ic_disable = 1;
+			continue;
+		} else if (strcmp(str, "dcdisable") == 0) {
+			txx9_dc_disable = 1;
+			continue;
+		} else if (strcmp(str, "toeoff") == 0) {
+			txx9_ccfg_toeon = 0;
+			continue;
+		} else if (strcmp(str, "toeon") == 0) {
+			txx9_ccfg_toeon = 1;
+			continue;
+		}
+		if (arcs_cmdline[0])
+			strcat(arcs_cmdline, " ");
+		strcat(arcs_cmdline, str);
+	}
+
+	txx9_cache_fixup();
+}
+
+static void __init select_board(void)
+{
+	const char *envstr;
+
+	/* first, determine by "board=" argument in preprocess_cmdline() */
+	if (txx9_board_vec)
+		return;
+	/* next, determine by "board" envvar */
+	envstr = prom_getenv("board");
+	if (envstr) {
+		txx9_board_vec = find_board_byname(envstr);
+		if (txx9_board_vec)
+			return;
+	}
+
+	/* select "default" board */
+#ifdef CONFIG_CPU_TX49XX
+	switch (TX4938_REV_PCODE()) {
+#ifdef CONFIG_TOSHIBA_RBTX4927
+	case 0x4927:
+		txx9_board_vec = &rbtx4927_vec;
+		break;
+	case 0x4937:
+		txx9_board_vec = &rbtx4937_vec;
+		break;
+#endif
+	}
+#endif
+}
+
+void __init prom_init(void)
+{
+	prom_init_cmdline();
+	preprocess_cmdline();
+	select_board();
+
+	strcpy(txx9_system_type, txx9_board_vec->system);
+
+	txx9_board_vec->prom_init();
+}
+
+const char *get_system_type(void)
+{
+	return txx9_system_type;
+}
+
+const char *__init prom_getenv(const char *name)
+{
+	const s32 *str;
+
+	if (fw_arg2 < CKSEG0)
+		return NULL;
+
+	str = (const s32 *)fw_arg2;
+	/* YAMON style ("name", "value" pairs) */
+	while (str[0] && str[1]) {
+		if (!strcmp((const char *)(unsigned long)str[0], name))
+			return (const char *)(unsigned long)str[1];
+		str += 2;
+	}
+	return NULL;
+}
+
+static void __noreturn txx9_machine_halt(void)
+{
+	local_irq_disable();
+	clear_c0_status(ST0_IM);
+	while (1) {
+		if (cpu_wait) {
+			(*cpu_wait)();
+			if (cpu_has_counter) {
+				/*
+				 * Clear counter interrupt while it
+				 * breaks WAIT instruction even if
+				 * masked.
+				 */
+				write_c0_compare(0);
+			}
+		}
+	}
+}
+
+/* Watchdog support */
+void __init txx9_wdt_init(unsigned long base)
+{
+	struct resource res = {
+		.start	= base,
+		.end	= base + 0x100 - 1,
+		.flags	= IORESOURCE_MEM,
+	};
+	platform_device_register_simple("txx9wdt", -1, &res, 1);
+}
+
+void txx9_wdt_now(unsigned long base)
+{
+	struct txx9_tmr_reg __iomem *tmrptr =
+		ioremap(base, sizeof(struct txx9_tmr_reg));
+	/* disable watch dog timer */
+	__raw_writel(TXx9_TMWTMR_WDIS | TXx9_TMWTMR_TWC, &tmrptr->wtmr);
+	__raw_writel(0, &tmrptr->tcr);
+	/* kick watchdog */
+	__raw_writel(TXx9_TMWTMR_TWIE, &tmrptr->wtmr);
+	__raw_writel(1, &tmrptr->cpra); /* immediate */
+	__raw_writel(TXx9_TMTCR_TCE | TXx9_TMTCR_CCDE | TXx9_TMTCR_TMODE_WDOG,
+		     &tmrptr->tcr);
+}
+
+/* SPI support */
+void __init txx9_spi_init(int busid, unsigned long base, int irq)
+{
+	struct resource res[] = {
+		{
+			.start	= base,
+			.end	= base + 0x20 - 1,
+			.flags	= IORESOURCE_MEM,
+		}, {
+			.start	= irq,
+			.flags	= IORESOURCE_IRQ,
+		},
+	};
+	platform_device_register_simple("spi_txx9", busid,
+					res, ARRAY_SIZE(res));
+}
+
+void __init txx9_ethaddr_init(unsigned int id, unsigned char *ethaddr)
+{
+	struct platform_device *pdev =
+		platform_device_alloc("tc35815-mac", id);
+	if (!pdev ||
+	    platform_device_add_data(pdev, ethaddr, 6) ||
+	    platform_device_add(pdev))
+		platform_device_put(pdev);
+}
+
+void __init txx9_sio_init(unsigned long baseaddr, int irq,
+			  unsigned int line, unsigned int sclk, int nocts)
+{
+#ifdef CONFIG_SERIAL_TXX9
+	struct uart_port req;
+
+	memset(&req, 0, sizeof(req));
+	req.line = line;
+	req.iotype = UPIO_MEM;
+	req.membase = ioremap(baseaddr, 0x24);
+	req.mapbase = baseaddr;
+	req.irq = irq;
+	if (!nocts)
+		req.flags |= UPF_BUGGY_UART /*HAVE_CTS_LINE*/;
+	if (sclk) {
+		req.flags |= UPF_MAGIC_MULTIPLIER /*USE_SCLK*/;
+		req.uartclk = sclk;
+	} else
+		req.uartclk = TXX9_IMCLK;
+	early_serial_txx9_setup(&req);
+#endif /* CONFIG_SERIAL_TXX9 */
+}
+
+#ifdef CONFIG_EARLY_PRINTK
+static void null_prom_putchar(char c)
+{
+}
+void (*txx9_prom_putchar)(char c) = null_prom_putchar;
+
+void prom_putchar(char c)
+{
+	txx9_prom_putchar(c);
+}
+
+static void __iomem *early_txx9_sio_port;
+
+static void early_txx9_sio_putchar(char c)
+{
+#define TXX9_SICISR	0x0c
+#define TXX9_SITFIFO	0x1c
+#define TXX9_SICISR_TXALS	0x00000002
+	while (!(__raw_readl(early_txx9_sio_port + TXX9_SICISR) &
+		 TXX9_SICISR_TXALS))
+		;
+	__raw_writel(c, early_txx9_sio_port + TXX9_SITFIFO);
+}
+
+void __init txx9_sio_putchar_init(unsigned long baseaddr)
+{
+	early_txx9_sio_port = ioremap(baseaddr, 0x24);
+	txx9_prom_putchar = early_txx9_sio_putchar;
+}
+#endif /* CONFIG_EARLY_PRINTK */
+
+/* wrappers */
+void __init plat_mem_setup(void)
+{
+	ioport_resource.start = 0;
+	ioport_resource.end = ~0UL;	/* no limit */
+	iomem_resource.start = 0;
+	iomem_resource.end = ~0UL;	/* no limit */
+
+	/* fallback restart/halt routines */
+	_machine_restart = (void (*)(char *))txx9_machine_halt;
+	_machine_halt = txx9_machine_halt;
+	pm_power_off = txx9_machine_halt;
+
+#ifdef CONFIG_PCI
+	pcibios_plat_setup = txx9_pcibios_setup;
+#endif
+	txx9_board_vec->mem_setup();
+}
+
+void __init arch_init_irq(void)
+{
+	txx9_board_vec->irq_setup();
+}
+
+void __init plat_time_init(void)
+{
+#ifdef CONFIG_CPU_TX49XX
+	mips_hpt_frequency = txx9_cpu_clock / 2;
+#endif
+	txx9_board_vec->time_init();
+}
+
+static void txx9_clk_init(void)
+{
+	struct clk_hw *hw;
+	int error;
+
+	hw = clk_hw_register_fixed_rate(NULL, "gbus", NULL, 0, txx9_gbus_clock);
+	if (IS_ERR(hw)) {
+		error = PTR_ERR(hw);
+		goto fail;
+	}
+
+	hw = clk_hw_register_fixed_factor(NULL, "imbus", "gbus", 0, 1, 2);
+	error = clk_hw_register_clkdev(hw, "imbus_clk", NULL);
+	if (error)
+		goto fail;
+
+#ifdef CONFIG_CPU_TX49XX
+	if (TX4938_REV_PCODE() == 0x4938) {
+		hw = clk_hw_register_fixed_factor(NULL, "spi", "gbus", 0, 1, 4);
+		error = clk_hw_register_clkdev(hw, "spi-baseclk", NULL);
+		if (error)
+			goto fail;
+	}
+#endif
+
+	return;
+
+fail:
+	pr_err("Failed to register clocks: %d\n", error);
+}
+
+static int __init _txx9_arch_init(void)
+{
+	txx9_clk_init();
+
+	if (txx9_board_vec->arch_init)
+		txx9_board_vec->arch_init();
+	return 0;
+}
+arch_initcall(_txx9_arch_init);
+
+static int __init _txx9_device_init(void)
+{
+	if (txx9_board_vec->device_init)
+		txx9_board_vec->device_init();
+	return 0;
+}
+device_initcall(_txx9_device_init);
+
+int (*txx9_irq_dispatch)(int pending);
+asmlinkage void plat_irq_dispatch(void)
+{
+	int pending = read_c0_status() & read_c0_cause() & ST0_IM;
+	int irq = txx9_irq_dispatch(pending);
+
+	if (likely(irq >= 0))
+		do_IRQ(irq);
+	else
+		spurious_interrupt();
+}
+
+/* see include/asm-mips/mach-tx39xx/mangle-port.h, for example. */
+#ifdef NEEDS_TXX9_SWIZZLE_ADDR_B
+static unsigned long __swizzle_addr_none(unsigned long port)
+{
+	return port;
+}
+unsigned long (*__swizzle_addr_b)(unsigned long port) = __swizzle_addr_none;
+EXPORT_SYMBOL(__swizzle_addr_b);
+#endif
+
+void __init txx9_physmap_flash_init(int no, unsigned long addr,
+				    unsigned long size,
+				    const struct physmap_flash_data *pdata)
+{
+#if IS_ENABLED(CONFIG_MTD_PHYSMAP)
+	struct resource res = {
+		.start = addr,
+		.end = addr + size - 1,
+		.flags = IORESOURCE_MEM,
+	};
+	struct platform_device *pdev;
+	static struct mtd_partition parts[2];
+	struct physmap_flash_data pdata_part;
+
+	/* If this area contained boot area, make separate partition */
+	if (pdata->nr_parts == 0 && !pdata->parts &&
+	    addr < 0x1fc00000 && addr + size > 0x1fc00000 &&
+	    !parts[0].name) {
+		parts[0].name = "boot";
+		parts[0].offset = 0x1fc00000 - addr;
+		parts[0].size = addr + size - 0x1fc00000;
+		parts[1].name = "user";
+		parts[1].offset = 0;
+		parts[1].size = 0x1fc00000 - addr;
+		pdata_part = *pdata;
+		pdata_part.nr_parts = ARRAY_SIZE(parts);
+		pdata_part.parts = parts;
+		pdata = &pdata_part;
+	}
+
+	pdev = platform_device_alloc("physmap-flash", no);
+	if (!pdev ||
+	    platform_device_add_resources(pdev, &res, 1) ||
+	    platform_device_add_data(pdev, pdata, sizeof(*pdata)) ||
+	    platform_device_add(pdev))
+		platform_device_put(pdev);
+#endif
+}
+
+void __init txx9_ndfmc_init(unsigned long baseaddr,
+			    const struct txx9ndfmc_platform_data *pdata)
+{
+#if IS_ENABLED(CONFIG_MTD_NAND_TXX9NDFMC)
+	struct resource res = {
+		.start = baseaddr,
+		.end = baseaddr + 0x1000 - 1,
+		.flags = IORESOURCE_MEM,
+	};
+	struct platform_device *pdev = platform_device_alloc("txx9ndfmc", -1);
+
+	if (!pdev ||
+	    platform_device_add_resources(pdev, &res, 1) ||
+	    platform_device_add_data(pdev, pdata, sizeof(*pdata)) ||
+	    platform_device_add(pdev))
+		platform_device_put(pdev);
+#endif
+}
+
+#if IS_ENABLED(CONFIG_LEDS_GPIO)
+static DEFINE_SPINLOCK(txx9_iocled_lock);
+
+#define TXX9_IOCLED_MAXLEDS 8
+
+struct txx9_iocled_data {
+	struct gpio_chip chip;
+	u8 cur_val;
+	void __iomem *mmioaddr;
+	struct gpio_led_platform_data pdata;
+	struct gpio_led leds[TXX9_IOCLED_MAXLEDS];
+	char names[TXX9_IOCLED_MAXLEDS][32];
+};
+
+static int txx9_iocled_get(struct gpio_chip *chip, unsigned int offset)
+{
+	struct txx9_iocled_data *data = gpiochip_get_data(chip);
+	return !!(data->cur_val & (1 << offset));
+}
+
+static void txx9_iocled_set(struct gpio_chip *chip, unsigned int offset,
+			    int value)
+{
+	struct txx9_iocled_data *data = gpiochip_get_data(chip);
+	unsigned long flags;
+	spin_lock_irqsave(&txx9_iocled_lock, flags);
+	if (value)
+		data->cur_val |= 1 << offset;
+	else
+		data->cur_val &= ~(1 << offset);
+	writeb(data->cur_val, data->mmioaddr);
+	mmiowb();
+	spin_unlock_irqrestore(&txx9_iocled_lock, flags);
+}
+
+static int txx9_iocled_dir_in(struct gpio_chip *chip, unsigned int offset)
+{
+	return 0;
+}
+
+static int txx9_iocled_dir_out(struct gpio_chip *chip, unsigned int offset,
+			       int value)
+{
+	txx9_iocled_set(chip, offset, value);
+	return 0;
+}
+
+void __init txx9_iocled_init(unsigned long baseaddr,
+			     int basenum, unsigned int num, int lowactive,
+			     const char *color, char **deftriggers)
+{
+	struct txx9_iocled_data *iocled;
+	struct platform_device *pdev;
+	int i;
+	static char *default_triggers[] __initdata = {
+		"heartbeat",
+		"disk-activity",
+		"nand-disk",
+		NULL,
+	};
+
+	if (!deftriggers)
+		deftriggers = default_triggers;
+	iocled = kzalloc(sizeof(*iocled), GFP_KERNEL);
+	if (!iocled)
+		return;
+	iocled->mmioaddr = ioremap(baseaddr, 1);
+	if (!iocled->mmioaddr)
+		goto out_free;
+	iocled->chip.get = txx9_iocled_get;
+	iocled->chip.set = txx9_iocled_set;
+	iocled->chip.direction_input = txx9_iocled_dir_in;
+	iocled->chip.direction_output = txx9_iocled_dir_out;
+	iocled->chip.label = "iocled";
+	iocled->chip.base = basenum;
+	iocled->chip.ngpio = num;
+	if (gpiochip_add_data(&iocled->chip, iocled))
+		goto out_unmap;
+	if (basenum < 0)
+		basenum = iocled->chip.base;
+
+	pdev = platform_device_alloc("leds-gpio", basenum);
+	if (!pdev)
+		goto out_gpio;
+	iocled->pdata.num_leds = num;
+	iocled->pdata.leds = iocled->leds;
+	for (i = 0; i < num; i++) {
+		struct gpio_led *led = &iocled->leds[i];
+		snprintf(iocled->names[i], sizeof(iocled->names[i]),
+			 "iocled:%s:%u", color, i);
+		led->name = iocled->names[i];
+		led->gpio = basenum + i;
+		led->active_low = lowactive;
+		if (deftriggers && *deftriggers)
+			led->default_trigger = *deftriggers++;
+	}
+	pdev->dev.platform_data = &iocled->pdata;
+	if (platform_device_add(pdev))
+		goto out_pdev;
+	return;
+
+out_pdev:
+	platform_device_put(pdev);
+out_gpio:
+	gpiochip_remove(&iocled->chip);
+out_unmap:
+	iounmap(iocled->mmioaddr);
+out_free:
+	kfree(iocled);
+}
+#else /* CONFIG_LEDS_GPIO */
+void __init txx9_iocled_init(unsigned long baseaddr,
+			     int basenum, unsigned int num, int lowactive,
+			     const char *color, char **deftriggers)
+{
+}
+#endif /* CONFIG_LEDS_GPIO */
+
+void __init txx9_dmac_init(int id, unsigned long baseaddr, int irq,
+			   const struct txx9dmac_platform_data *pdata)
+{
+#if IS_ENABLED(CONFIG_TXX9_DMAC)
+	struct resource res[] = {
+		{
+			.start = baseaddr,
+			.end = baseaddr + 0x800 - 1,
+			.flags = IORESOURCE_MEM,
+#ifndef CONFIG_MACH_TX49XX
+		}, {
+			.start = irq,
+			.flags = IORESOURCE_IRQ,
+#endif
+		}
+	};
+#ifdef CONFIG_MACH_TX49XX
+	struct resource chan_res[] = {
+		{
+			.flags = IORESOURCE_IRQ,
+		}
+	};
+#endif
+	struct platform_device *pdev = platform_device_alloc("txx9dmac", id);
+	struct txx9dmac_chan_platform_data cpdata;
+	int i;
+
+	if (!pdev ||
+	    platform_device_add_resources(pdev, res, ARRAY_SIZE(res)) ||
+	    platform_device_add_data(pdev, pdata, sizeof(*pdata)) ||
+	    platform_device_add(pdev)) {
+		platform_device_put(pdev);
+		return;
+	}
+	memset(&cpdata, 0, sizeof(cpdata));
+	cpdata.dmac_dev = pdev;
+	for (i = 0; i < TXX9_DMA_MAX_NR_CHANNELS; i++) {
+#ifdef CONFIG_MACH_TX49XX
+		chan_res[0].start = irq + i;
+#endif
+		pdev = platform_device_alloc("txx9dmac-chan",
+					     id * TXX9_DMA_MAX_NR_CHANNELS + i);
+		if (!pdev ||
+#ifdef CONFIG_MACH_TX49XX
+		    platform_device_add_resources(pdev, chan_res,
+						  ARRAY_SIZE(chan_res)) ||
+#endif
+		    platform_device_add_data(pdev, &cpdata, sizeof(cpdata)) ||
+		    platform_device_add(pdev))
+			platform_device_put(pdev);
+	}
+#endif
+}
+
+void __init txx9_aclc_init(unsigned long baseaddr, int irq,
+			   unsigned int dmac_id,
+			   unsigned int dma_chan_out,
+			   unsigned int dma_chan_in)
+{
+}
+
+static struct bus_type txx9_sramc_subsys = {
+	.name = "txx9_sram",
+	.dev_name = "txx9_sram",
+};
+
+struct txx9_sramc_dev {
+	struct device dev;
+	struct bin_attribute bindata_attr;
+	void __iomem *base;
+};
+
+static ssize_t txx9_sram_read(struct file *filp, struct kobject *kobj,
+			      struct bin_attribute *bin_attr,
+			      char *buf, loff_t pos, size_t size)
+{
+	struct txx9_sramc_dev *dev = bin_attr->private;
+	size_t ramsize = bin_attr->size;
+
+	if (pos >= ramsize)
+		return 0;
+	if (pos + size > ramsize)
+		size = ramsize - pos;
+	memcpy_fromio(buf, dev->base + pos, size);
+	return size;
+}
+
+static ssize_t txx9_sram_write(struct file *filp, struct kobject *kobj,
+			       struct bin_attribute *bin_attr,
+			       char *buf, loff_t pos, size_t size)
+{
+	struct txx9_sramc_dev *dev = bin_attr->private;
+	size_t ramsize = bin_attr->size;
+
+	if (pos >= ramsize)
+		return 0;
+	if (pos + size > ramsize)
+		size = ramsize - pos;
+	memcpy_toio(dev->base + pos, buf, size);
+	return size;
+}
+
+static void txx9_device_release(struct device *dev)
+{
+	struct txx9_sramc_dev *tdev;
+
+	tdev = container_of(dev, struct txx9_sramc_dev, dev);
+	kfree(tdev);
+}
+
+void __init txx9_sramc_init(struct resource *r)
+{
+	struct txx9_sramc_dev *dev;
+	size_t size;
+	int err;
+
+	err = subsys_system_register(&txx9_sramc_subsys, NULL);
+	if (err)
+		return;
+	dev = kzalloc(sizeof(*dev), GFP_KERNEL);
+	if (!dev)
+		return;
+	size = resource_size(r);
+	dev->base = ioremap(r->start, size);
+	if (!dev->base) {
+		kfree(dev);
+		return;
+	}
+	dev->dev.release = &txx9_device_release;
+	dev->dev.bus = &txx9_sramc_subsys;
+	sysfs_bin_attr_init(&dev->bindata_attr);
+	dev->bindata_attr.attr.name = "bindata";
+	dev->bindata_attr.attr.mode = S_IRUSR | S_IWUSR;
+	dev->bindata_attr.read = txx9_sram_read;
+	dev->bindata_attr.write = txx9_sram_write;
+	dev->bindata_attr.size = size;
+	dev->bindata_attr.private = dev;
+	err = device_register(&dev->dev);
+	if (err)
+		goto exit_put;
+	err = sysfs_create_bin_file(&dev->dev.kobj, &dev->bindata_attr);
+	if (err) {
+		iounmap(dev->base);
+		device_unregister(&dev->dev);
+	}
+	return;
+exit_put:
+	iounmap(dev->base);
+	put_device(&dev->dev);
+}
diff --git a/arch/mips/txx9/generic/setup_tx4927.c b/arch/mips/txx9/generic/setup_tx4927.c
new file mode 100644
index 000000000..63f9725b2
--- /dev/null
+++ b/arch/mips/txx9/generic/setup_tx4927.c
@@ -0,0 +1,337 @@
+/*
+ * TX4927 setup routines
+ * Based on linux/arch/mips/txx9/rbtx4938/setup.c,
+ *	    and RBTX49xx patch from CELF patch archive.
+ *
+ * 2003-2005 (c) MontaVista Software, Inc.
+ * (C) Copyright TOSHIBA CORPORATION 2000-2001, 2004-2007
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#include <linux/init.h>
+#include <linux/ioport.h>
+#include <linux/delay.h>
+#include <linux/param.h>
+#include <linux/ptrace.h>
+#include <linux/mtd/physmap.h>
+#include <asm/reboot.h>
+#include <asm/traps.h>
+#include <asm/txx9irq.h>
+#include <asm/txx9tmr.h>
+#include <asm/txx9pio.h>
+#include <asm/txx9/generic.h>
+#include <asm/txx9/dmac.h>
+#include <asm/txx9/tx4927.h>
+
+static void __init tx4927_wdr_init(void)
+{
+	/* report watchdog reset status */
+	if (____raw_readq(&tx4927_ccfgptr->ccfg) & TX4927_CCFG_WDRST)
+		pr_warn("Watchdog reset detected at 0x%lx\n",
+			read_c0_errorepc());
+	/* clear WatchDogReset (W1C) */
+	tx4927_ccfg_set(TX4927_CCFG_WDRST);
+	/* do reset on watchdog */
+	tx4927_ccfg_set(TX4927_CCFG_WR);
+}
+
+void __init tx4927_wdt_init(void)
+{
+	txx9_wdt_init(TX4927_TMR_REG(2) & 0xfffffffffULL);
+}
+
+static void tx4927_machine_restart(char *command)
+{
+	local_irq_disable();
+	pr_emerg("Rebooting (with %s watchdog reset)...\n",
+		 (____raw_readq(&tx4927_ccfgptr->ccfg) & TX4927_CCFG_WDREXEN) ?
+		 "external" : "internal");
+	/* clear watchdog status */
+	tx4927_ccfg_set(TX4927_CCFG_WDRST);	/* W1C */
+	txx9_wdt_now(TX4927_TMR_REG(2) & 0xfffffffffULL);
+	while (!(____raw_readq(&tx4927_ccfgptr->ccfg) & TX4927_CCFG_WDRST))
+		;
+	mdelay(10);
+	if (____raw_readq(&tx4927_ccfgptr->ccfg) & TX4927_CCFG_WDREXEN) {
+		pr_emerg("Rebooting (with internal watchdog reset)...\n");
+		/* External WDRST failed.  Do internal watchdog reset */
+		tx4927_ccfg_clear(TX4927_CCFG_WDREXEN);
+	}
+	/* fallback */
+	(*_machine_halt)();
+}
+
+void show_registers(struct pt_regs *regs);
+static int tx4927_be_handler(struct pt_regs *regs, int is_fixup)
+{
+	int data = regs->cp0_cause & 4;
+	console_verbose();
+	pr_err("%cBE exception at %#lx\n", data ? 'D' : 'I', regs->cp0_epc);
+	pr_err("ccfg:%llx, toea:%llx\n",
+	       (unsigned long long)____raw_readq(&tx4927_ccfgptr->ccfg),
+	       (unsigned long long)____raw_readq(&tx4927_ccfgptr->toea));
+#ifdef CONFIG_PCI
+	tx4927_report_pcic_status();
+#endif
+	show_registers(regs);
+	panic("BusError!");
+}
+static void __init tx4927_be_init(void)
+{
+	mips_set_be_handler(tx4927_be_handler);
+}
+
+static struct resource tx4927_sdram_resource[4];
+
+void __init tx4927_setup(void)
+{
+	int i;
+	__u32 divmode;
+	unsigned int cpuclk = 0;
+	u64 ccfg;
+
+	txx9_reg_res_init(TX4927_REV_PCODE(), TX4927_REG_BASE,
+			  TX4927_REG_SIZE);
+	set_c0_config(TX49_CONF_CWFON);
+
+	/* SDRAMC,EBUSC are configured by PROM */
+	for (i = 0; i < 8; i++) {
+		if (!(TX4927_EBUSC_CR(i) & 0x8))
+			continue;	/* disabled */
+		txx9_ce_res[i].start = (unsigned long)TX4927_EBUSC_BA(i);
+		txx9_ce_res[i].end =
+			txx9_ce_res[i].start + TX4927_EBUSC_SIZE(i) - 1;
+		request_resource(&iomem_resource, &txx9_ce_res[i]);
+	}
+
+	/* clocks */
+	ccfg = ____raw_readq(&tx4927_ccfgptr->ccfg);
+	if (txx9_master_clock) {
+		/* calculate gbus_clock and cpu_clock from master_clock */
+		divmode = (__u32)ccfg & TX4927_CCFG_DIVMODE_MASK;
+		switch (divmode) {
+		case TX4927_CCFG_DIVMODE_8:
+		case TX4927_CCFG_DIVMODE_10:
+		case TX4927_CCFG_DIVMODE_12:
+		case TX4927_CCFG_DIVMODE_16:
+			txx9_gbus_clock = txx9_master_clock * 4; break;
+		default:
+			txx9_gbus_clock = txx9_master_clock;
+		}
+		switch (divmode) {
+		case TX4927_CCFG_DIVMODE_2:
+		case TX4927_CCFG_DIVMODE_8:
+			cpuclk = txx9_gbus_clock * 2; break;
+		case TX4927_CCFG_DIVMODE_2_5:
+		case TX4927_CCFG_DIVMODE_10:
+			cpuclk = txx9_gbus_clock * 5 / 2; break;
+		case TX4927_CCFG_DIVMODE_3:
+		case TX4927_CCFG_DIVMODE_12:
+			cpuclk = txx9_gbus_clock * 3; break;
+		case TX4927_CCFG_DIVMODE_4:
+		case TX4927_CCFG_DIVMODE_16:
+			cpuclk = txx9_gbus_clock * 4; break;
+		}
+		txx9_cpu_clock = cpuclk;
+	} else {
+		if (txx9_cpu_clock == 0)
+			txx9_cpu_clock = 200000000;	/* 200MHz */
+		/* calculate gbus_clock and master_clock from cpu_clock */
+		cpuclk = txx9_cpu_clock;
+		divmode = (__u32)ccfg & TX4927_CCFG_DIVMODE_MASK;
+		switch (divmode) {
+		case TX4927_CCFG_DIVMODE_2:
+		case TX4927_CCFG_DIVMODE_8:
+			txx9_gbus_clock = cpuclk / 2; break;
+		case TX4927_CCFG_DIVMODE_2_5:
+		case TX4927_CCFG_DIVMODE_10:
+			txx9_gbus_clock = cpuclk * 2 / 5; break;
+		case TX4927_CCFG_DIVMODE_3:
+		case TX4927_CCFG_DIVMODE_12:
+			txx9_gbus_clock = cpuclk / 3; break;
+		case TX4927_CCFG_DIVMODE_4:
+		case TX4927_CCFG_DIVMODE_16:
+			txx9_gbus_clock = cpuclk / 4; break;
+		}
+		switch (divmode) {
+		case TX4927_CCFG_DIVMODE_8:
+		case TX4927_CCFG_DIVMODE_10:
+		case TX4927_CCFG_DIVMODE_12:
+		case TX4927_CCFG_DIVMODE_16:
+			txx9_master_clock = txx9_gbus_clock / 4; break;
+		default:
+			txx9_master_clock = txx9_gbus_clock;
+		}
+	}
+	/* change default value to udelay/mdelay take reasonable time */
+	loops_per_jiffy = txx9_cpu_clock / HZ / 2;
+
+	/* CCFG */
+	tx4927_wdr_init();
+	/* clear BusErrorOnWrite flag (W1C) */
+	tx4927_ccfg_set(TX4927_CCFG_BEOW);
+	/* enable Timeout BusError */
+	if (txx9_ccfg_toeon)
+		tx4927_ccfg_set(TX4927_CCFG_TOE);
+
+	/* DMA selection */
+	txx9_clear64(&tx4927_ccfgptr->pcfg, TX4927_PCFG_DMASEL_ALL);
+
+	/* Use external clock for external arbiter */
+	if (!(____raw_readq(&tx4927_ccfgptr->ccfg) & TX4927_CCFG_PCIARB))
+		txx9_clear64(&tx4927_ccfgptr->pcfg, TX4927_PCFG_PCICLKEN_ALL);
+
+	pr_info("%s -- %dMHz(M%dMHz) CRIR:%08x CCFG:%llx PCFG:%llx\n",
+		txx9_pcode_str, (cpuclk + 500000) / 1000000,
+		(txx9_master_clock + 500000) / 1000000,
+		(__u32)____raw_readq(&tx4927_ccfgptr->crir),
+		____raw_readq(&tx4927_ccfgptr->ccfg),
+		____raw_readq(&tx4927_ccfgptr->pcfg));
+
+	pr_info("%s SDRAMC --", txx9_pcode_str);
+	for (i = 0; i < 4; i++) {
+		__u64 cr = TX4927_SDRAMC_CR(i);
+		unsigned long base, size;
+		if (!((__u32)cr & 0x00000400))
+			continue;	/* disabled */
+		base = (unsigned long)(cr >> 49) << 21;
+		size = (((unsigned long)(cr >> 33) & 0x7fff) + 1) << 21;
+		pr_cont(" CR%d:%016llx", i, cr);
+		tx4927_sdram_resource[i].name = "SDRAM";
+		tx4927_sdram_resource[i].start = base;
+		tx4927_sdram_resource[i].end = base + size - 1;
+		tx4927_sdram_resource[i].flags = IORESOURCE_MEM;
+		request_resource(&iomem_resource, &tx4927_sdram_resource[i]);
+	}
+	pr_cont(" TR:%09llx\n", ____raw_readq(&tx4927_sdramcptr->tr));
+
+	/* TMR */
+	/* disable all timers */
+	for (i = 0; i < TX4927_NR_TMR; i++)
+		txx9_tmr_init(TX4927_TMR_REG(i) & 0xfffffffffULL);
+
+	/* PIO */
+	__raw_writel(0, &tx4927_pioptr->maskcpu);
+	__raw_writel(0, &tx4927_pioptr->maskext);
+
+	_machine_restart = tx4927_machine_restart;
+	board_be_init = tx4927_be_init;
+}
+
+void __init tx4927_time_init(unsigned int tmrnr)
+{
+	if (____raw_readq(&tx4927_ccfgptr->ccfg) & TX4927_CCFG_TINTDIS)
+		txx9_clockevent_init(TX4927_TMR_REG(tmrnr) & 0xfffffffffULL,
+				     TXX9_IRQ_BASE + TX4927_IR_TMR(tmrnr),
+				     TXX9_IMCLK);
+}
+
+void __init tx4927_sio_init(unsigned int sclk, unsigned int cts_mask)
+{
+	int i;
+
+	for (i = 0; i < 2; i++)
+		txx9_sio_init(TX4927_SIO_REG(i) & 0xfffffffffULL,
+			      TXX9_IRQ_BASE + TX4927_IR_SIO(i),
+			      i, sclk, (1 << i) & cts_mask);
+}
+
+void __init tx4927_mtd_init(int ch)
+{
+	struct physmap_flash_data pdata = {
+		.width = TX4927_EBUSC_WIDTH(ch) / 8,
+	};
+	unsigned long start = txx9_ce_res[ch].start;
+	unsigned long size = txx9_ce_res[ch].end - start + 1;
+
+	if (!(TX4927_EBUSC_CR(ch) & 0x8))
+		return; /* disabled */
+	txx9_physmap_flash_init(ch, start, size, &pdata);
+}
+
+void __init tx4927_dmac_init(int memcpy_chan)
+{
+	struct txx9dmac_platform_data plat_data = {
+		.memcpy_chan = memcpy_chan,
+		.have_64bit_regs = true,
+	};
+
+	txx9_dmac_init(0, TX4927_DMA_REG & 0xfffffffffULL,
+		       TXX9_IRQ_BASE + TX4927_IR_DMA(0), &plat_data);
+}
+
+void __init tx4927_aclc_init(unsigned int dma_chan_out,
+			     unsigned int dma_chan_in)
+{
+	u64 pcfg = __raw_readq(&tx4927_ccfgptr->pcfg);
+	__u64 dmasel_mask = 0, dmasel = 0;
+	unsigned long flags;
+
+	if (!(pcfg & TX4927_PCFG_SEL2))
+		return;
+	/* setup DMASEL (playback:ACLC ch0, capture:ACLC ch1) */
+	switch (dma_chan_out) {
+	case 0:
+		dmasel_mask |= TX4927_PCFG_DMASEL0_MASK;
+		dmasel |= TX4927_PCFG_DMASEL0_ACL0;
+		break;
+	case 2:
+		dmasel_mask |= TX4927_PCFG_DMASEL2_MASK;
+		dmasel |= TX4927_PCFG_DMASEL2_ACL0;
+		break;
+	default:
+		return;
+	}
+	switch (dma_chan_in) {
+	case 1:
+		dmasel_mask |= TX4927_PCFG_DMASEL1_MASK;
+		dmasel |= TX4927_PCFG_DMASEL1_ACL1;
+		break;
+	case 3:
+		dmasel_mask |= TX4927_PCFG_DMASEL3_MASK;
+		dmasel |= TX4927_PCFG_DMASEL3_ACL1;
+		break;
+	default:
+		return;
+	}
+	local_irq_save(flags);
+	txx9_clear64(&tx4927_ccfgptr->pcfg, dmasel_mask);
+	txx9_set64(&tx4927_ccfgptr->pcfg, dmasel);
+	local_irq_restore(flags);
+	txx9_aclc_init(TX4927_ACLC_REG & 0xfffffffffULL,
+		       TXX9_IRQ_BASE + TX4927_IR_ACLC,
+		       0, dma_chan_out, dma_chan_in);
+}
+
+static void __init tx4927_stop_unused_modules(void)
+{
+	__u64 pcfg, rst = 0, ckd = 0;
+	char buf[128];
+
+	buf[0] = '\0';
+	local_irq_disable();
+	pcfg = ____raw_readq(&tx4927_ccfgptr->pcfg);
+	if (!(pcfg & TX4927_PCFG_SEL2)) {
+		rst |= TX4927_CLKCTR_ACLRST;
+		ckd |= TX4927_CLKCTR_ACLCKD;
+		strcat(buf, " ACLC");
+	}
+	if (rst | ckd) {
+		txx9_set64(&tx4927_ccfgptr->clkctr, rst);
+		txx9_set64(&tx4927_ccfgptr->clkctr, ckd);
+	}
+	local_irq_enable();
+	if (buf[0])
+		pr_info("%s: stop%s\n", txx9_pcode_str, buf);
+}
+
+static int __init tx4927_late_init(void)
+{
+	if (txx9_pcode != 0x4927)
+		return -ENODEV;
+	tx4927_stop_unused_modules();
+	return 0;
+}
+late_initcall(tx4927_late_init);
diff --git a/arch/mips/txx9/generic/setup_tx4938.c b/arch/mips/txx9/generic/setup_tx4938.c
new file mode 100644
index 000000000..ba646548c
--- /dev/null
+++ b/arch/mips/txx9/generic/setup_tx4938.c
@@ -0,0 +1,485 @@
+/*
+ * TX4938/4937 setup routines
+ * Based on linux/arch/mips/txx9/rbtx4938/setup.c,
+ *	    and RBTX49xx patch from CELF patch archive.
+ *
+ * 2003-2005 (c) MontaVista Software, Inc.
+ * (C) Copyright TOSHIBA CORPORATION 2000-2001, 2004-2007
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#include <linux/init.h>
+#include <linux/ioport.h>
+#include <linux/delay.h>
+#include <linux/param.h>
+#include <linux/ptrace.h>
+#include <linux/mtd/physmap.h>
+#include <linux/platform_device.h>
+#include <linux/platform_data/txx9/ndfmc.h>
+#include <asm/reboot.h>
+#include <asm/traps.h>
+#include <asm/txx9irq.h>
+#include <asm/txx9tmr.h>
+#include <asm/txx9pio.h>
+#include <asm/txx9/generic.h>
+#include <asm/txx9/dmac.h>
+#include <asm/txx9/tx4938.h>
+
+static void __init tx4938_wdr_init(void)
+{
+	/* report watchdog reset status */
+	if (____raw_readq(&tx4938_ccfgptr->ccfg) & TX4938_CCFG_WDRST)
+		pr_warn("Watchdog reset detected at 0x%lx\n",
+			read_c0_errorepc());
+	/* clear WatchDogReset (W1C) */
+	tx4938_ccfg_set(TX4938_CCFG_WDRST);
+	/* do reset on watchdog */
+	tx4938_ccfg_set(TX4938_CCFG_WR);
+}
+
+void __init tx4938_wdt_init(void)
+{
+	txx9_wdt_init(TX4938_TMR_REG(2) & 0xfffffffffULL);
+}
+
+static void tx4938_machine_restart(char *command)
+{
+	local_irq_disable();
+	pr_emerg("Rebooting (with %s watchdog reset)...\n",
+		 (____raw_readq(&tx4938_ccfgptr->ccfg) & TX4938_CCFG_WDREXEN) ?
+		 "external" : "internal");
+	/* clear watchdog status */
+	tx4938_ccfg_set(TX4938_CCFG_WDRST);	/* W1C */
+	txx9_wdt_now(TX4938_TMR_REG(2) & 0xfffffffffULL);
+	while (!(____raw_readq(&tx4938_ccfgptr->ccfg) & TX4938_CCFG_WDRST))
+		;
+	mdelay(10);
+	if (____raw_readq(&tx4938_ccfgptr->ccfg) & TX4938_CCFG_WDREXEN) {
+		pr_emerg("Rebooting (with internal watchdog reset)...\n");
+		/* External WDRST failed.  Do internal watchdog reset */
+		tx4938_ccfg_clear(TX4938_CCFG_WDREXEN);
+	}
+	/* fallback */
+	(*_machine_halt)();
+}
+
+void show_registers(struct pt_regs *regs);
+static int tx4938_be_handler(struct pt_regs *regs, int is_fixup)
+{
+	int data = regs->cp0_cause & 4;
+	console_verbose();
+	pr_err("%cBE exception at %#lx\n", data ? 'D' : 'I', regs->cp0_epc);
+	pr_err("ccfg:%llx, toea:%llx\n",
+	       (unsigned long long)____raw_readq(&tx4938_ccfgptr->ccfg),
+	       (unsigned long long)____raw_readq(&tx4938_ccfgptr->toea));
+#ifdef CONFIG_PCI
+	tx4927_report_pcic_status();
+#endif
+	show_registers(regs);
+	panic("BusError!");
+}
+static void __init tx4938_be_init(void)
+{
+	mips_set_be_handler(tx4938_be_handler);
+}
+
+static struct resource tx4938_sdram_resource[4];
+static struct resource tx4938_sram_resource;
+
+#define TX4938_SRAM_SIZE 0x800
+
+void __init tx4938_setup(void)
+{
+	int i;
+	__u32 divmode;
+	unsigned int cpuclk = 0;
+	u64 ccfg;
+
+	txx9_reg_res_init(TX4938_REV_PCODE(), TX4938_REG_BASE,
+			  TX4938_REG_SIZE);
+	set_c0_config(TX49_CONF_CWFON);
+
+	/* SDRAMC,EBUSC are configured by PROM */
+	for (i = 0; i < 8; i++) {
+		if (!(TX4938_EBUSC_CR(i) & 0x8))
+			continue;	/* disabled */
+		txx9_ce_res[i].start = (unsigned long)TX4938_EBUSC_BA(i);
+		txx9_ce_res[i].end =
+			txx9_ce_res[i].start + TX4938_EBUSC_SIZE(i) - 1;
+		request_resource(&iomem_resource, &txx9_ce_res[i]);
+	}
+
+	/* clocks */
+	ccfg = ____raw_readq(&tx4938_ccfgptr->ccfg);
+	if (txx9_master_clock) {
+		/* calculate gbus_clock and cpu_clock from master_clock */
+		divmode = (__u32)ccfg & TX4938_CCFG_DIVMODE_MASK;
+		switch (divmode) {
+		case TX4938_CCFG_DIVMODE_8:
+		case TX4938_CCFG_DIVMODE_10:
+		case TX4938_CCFG_DIVMODE_12:
+		case TX4938_CCFG_DIVMODE_16:
+		case TX4938_CCFG_DIVMODE_18:
+			txx9_gbus_clock = txx9_master_clock * 4; break;
+		default:
+			txx9_gbus_clock = txx9_master_clock;
+		}
+		switch (divmode) {
+		case TX4938_CCFG_DIVMODE_2:
+		case TX4938_CCFG_DIVMODE_8:
+			cpuclk = txx9_gbus_clock * 2; break;
+		case TX4938_CCFG_DIVMODE_2_5:
+		case TX4938_CCFG_DIVMODE_10:
+			cpuclk = txx9_gbus_clock * 5 / 2; break;
+		case TX4938_CCFG_DIVMODE_3:
+		case TX4938_CCFG_DIVMODE_12:
+			cpuclk = txx9_gbus_clock * 3; break;
+		case TX4938_CCFG_DIVMODE_4:
+		case TX4938_CCFG_DIVMODE_16:
+			cpuclk = txx9_gbus_clock * 4; break;
+		case TX4938_CCFG_DIVMODE_4_5:
+		case TX4938_CCFG_DIVMODE_18:
+			cpuclk = txx9_gbus_clock * 9 / 2; break;
+		}
+		txx9_cpu_clock = cpuclk;
+	} else {
+		if (txx9_cpu_clock == 0)
+			txx9_cpu_clock = 300000000;	/* 300MHz */
+		/* calculate gbus_clock and master_clock from cpu_clock */
+		cpuclk = txx9_cpu_clock;
+		divmode = (__u32)ccfg & TX4938_CCFG_DIVMODE_MASK;
+		switch (divmode) {
+		case TX4938_CCFG_DIVMODE_2:
+		case TX4938_CCFG_DIVMODE_8:
+			txx9_gbus_clock = cpuclk / 2; break;
+		case TX4938_CCFG_DIVMODE_2_5:
+		case TX4938_CCFG_DIVMODE_10:
+			txx9_gbus_clock = cpuclk * 2 / 5; break;
+		case TX4938_CCFG_DIVMODE_3:
+		case TX4938_CCFG_DIVMODE_12:
+			txx9_gbus_clock = cpuclk / 3; break;
+		case TX4938_CCFG_DIVMODE_4:
+		case TX4938_CCFG_DIVMODE_16:
+			txx9_gbus_clock = cpuclk / 4; break;
+		case TX4938_CCFG_DIVMODE_4_5:
+		case TX4938_CCFG_DIVMODE_18:
+			txx9_gbus_clock = cpuclk * 2 / 9; break;
+		}
+		switch (divmode) {
+		case TX4938_CCFG_DIVMODE_8:
+		case TX4938_CCFG_DIVMODE_10:
+		case TX4938_CCFG_DIVMODE_12:
+		case TX4938_CCFG_DIVMODE_16:
+		case TX4938_CCFG_DIVMODE_18:
+			txx9_master_clock = txx9_gbus_clock / 4; break;
+		default:
+			txx9_master_clock = txx9_gbus_clock;
+		}
+	}
+	/* change default value to udelay/mdelay take reasonable time */
+	loops_per_jiffy = txx9_cpu_clock / HZ / 2;
+
+	/* CCFG */
+	tx4938_wdr_init();
+	/* clear BusErrorOnWrite flag (W1C) */
+	tx4938_ccfg_set(TX4938_CCFG_BEOW);
+	/* enable Timeout BusError */
+	if (txx9_ccfg_toeon)
+		tx4938_ccfg_set(TX4938_CCFG_TOE);
+
+	/* DMA selection */
+	txx9_clear64(&tx4938_ccfgptr->pcfg, TX4938_PCFG_DMASEL_ALL);
+
+	/* Use external clock for external arbiter */
+	if (!(____raw_readq(&tx4938_ccfgptr->ccfg) & TX4938_CCFG_PCIARB))
+		txx9_clear64(&tx4938_ccfgptr->pcfg, TX4938_PCFG_PCICLKEN_ALL);
+
+	pr_info("%s -- %dMHz(M%dMHz) CRIR:%08x CCFG:%llx PCFG:%llx\n",
+		txx9_pcode_str, (cpuclk + 500000) / 1000000,
+		(txx9_master_clock + 500000) / 1000000,
+		(__u32)____raw_readq(&tx4938_ccfgptr->crir),
+		____raw_readq(&tx4938_ccfgptr->ccfg),
+		____raw_readq(&tx4938_ccfgptr->pcfg));
+
+	pr_info("%s SDRAMC --", txx9_pcode_str);
+	for (i = 0; i < 4; i++) {
+		__u64 cr = TX4938_SDRAMC_CR(i);
+		unsigned long base, size;
+		if (!((__u32)cr & 0x00000400))
+			continue;	/* disabled */
+		base = (unsigned long)(cr >> 49) << 21;
+		size = (((unsigned long)(cr >> 33) & 0x7fff) + 1) << 21;
+		pr_cont(" CR%d:%016llx", i, cr);
+		tx4938_sdram_resource[i].name = "SDRAM";
+		tx4938_sdram_resource[i].start = base;
+		tx4938_sdram_resource[i].end = base + size - 1;
+		tx4938_sdram_resource[i].flags = IORESOURCE_MEM;
+		request_resource(&iomem_resource, &tx4938_sdram_resource[i]);
+	}
+	pr_cont(" TR:%09llx\n", ____raw_readq(&tx4938_sdramcptr->tr));
+
+	/* SRAM */
+	if (txx9_pcode == 0x4938 && ____raw_readq(&tx4938_sramcptr->cr) & 1) {
+		unsigned int size = TX4938_SRAM_SIZE;
+		tx4938_sram_resource.name = "SRAM";
+		tx4938_sram_resource.start =
+			(____raw_readq(&tx4938_sramcptr->cr) >> (39-11))
+			& ~(size - 1);
+		tx4938_sram_resource.end =
+			tx4938_sram_resource.start + TX4938_SRAM_SIZE - 1;
+		tx4938_sram_resource.flags = IORESOURCE_MEM;
+		request_resource(&iomem_resource, &tx4938_sram_resource);
+	}
+
+	/* TMR */
+	/* disable all timers */
+	for (i = 0; i < TX4938_NR_TMR; i++)
+		txx9_tmr_init(TX4938_TMR_REG(i) & 0xfffffffffULL);
+
+	/* PIO */
+	__raw_writel(0, &tx4938_pioptr->maskcpu);
+	__raw_writel(0, &tx4938_pioptr->maskext);
+
+	if (txx9_pcode == 0x4938) {
+		__u64 pcfg = ____raw_readq(&tx4938_ccfgptr->pcfg);
+		/* set PCIC1 reset */
+		txx9_set64(&tx4938_ccfgptr->clkctr, TX4938_CLKCTR_PCIC1RST);
+		if (pcfg & (TX4938_PCFG_ETH0_SEL | TX4938_PCFG_ETH1_SEL)) {
+			mdelay(1);	/* at least 128 cpu clock */
+			/* clear PCIC1 reset */
+			txx9_clear64(&tx4938_ccfgptr->clkctr,
+				     TX4938_CLKCTR_PCIC1RST);
+		} else {
+			pr_info("%s: stop PCIC1\n", txx9_pcode_str);
+			/* stop PCIC1 */
+			txx9_set64(&tx4938_ccfgptr->clkctr,
+				   TX4938_CLKCTR_PCIC1CKD);
+		}
+		if (!(pcfg & TX4938_PCFG_ETH0_SEL)) {
+			pr_info("%s: stop ETH0\n", txx9_pcode_str);
+			txx9_set64(&tx4938_ccfgptr->clkctr,
+				   TX4938_CLKCTR_ETH0RST);
+			txx9_set64(&tx4938_ccfgptr->clkctr,
+				   TX4938_CLKCTR_ETH0CKD);
+		}
+		if (!(pcfg & TX4938_PCFG_ETH1_SEL)) {
+			pr_info("%s: stop ETH1\n", txx9_pcode_str);
+			txx9_set64(&tx4938_ccfgptr->clkctr,
+				   TX4938_CLKCTR_ETH1RST);
+			txx9_set64(&tx4938_ccfgptr->clkctr,
+				   TX4938_CLKCTR_ETH1CKD);
+		}
+	}
+
+	_machine_restart = tx4938_machine_restart;
+	board_be_init = tx4938_be_init;
+}
+
+void __init tx4938_time_init(unsigned int tmrnr)
+{
+	if (____raw_readq(&tx4938_ccfgptr->ccfg) & TX4938_CCFG_TINTDIS)
+		txx9_clockevent_init(TX4938_TMR_REG(tmrnr) & 0xfffffffffULL,
+				     TXX9_IRQ_BASE + TX4938_IR_TMR(tmrnr),
+				     TXX9_IMCLK);
+}
+
+void __init tx4938_sio_init(unsigned int sclk, unsigned int cts_mask)
+{
+	int i;
+	unsigned int ch_mask = 0;
+
+	if (__raw_readq(&tx4938_ccfgptr->pcfg) & TX4938_PCFG_ETH0_SEL)
+		ch_mask |= 1 << 1; /* disable SIO1 by PCFG setting */
+	for (i = 0; i < 2; i++) {
+		if ((1 << i) & ch_mask)
+			continue;
+		txx9_sio_init(TX4938_SIO_REG(i) & 0xfffffffffULL,
+			      TXX9_IRQ_BASE + TX4938_IR_SIO(i),
+			      i, sclk, (1 << i) & cts_mask);
+	}
+}
+
+void __init tx4938_spi_init(int busid)
+{
+	txx9_spi_init(busid, TX4938_SPI_REG & 0xfffffffffULL,
+		      TXX9_IRQ_BASE + TX4938_IR_SPI);
+}
+
+void __init tx4938_ethaddr_init(unsigned char *addr0, unsigned char *addr1)
+{
+	u64 pcfg = __raw_readq(&tx4938_ccfgptr->pcfg);
+
+	if (addr0 && (pcfg & TX4938_PCFG_ETH0_SEL))
+		txx9_ethaddr_init(TXX9_IRQ_BASE + TX4938_IR_ETH0, addr0);
+	if (addr1 && (pcfg & TX4938_PCFG_ETH1_SEL))
+		txx9_ethaddr_init(TXX9_IRQ_BASE + TX4938_IR_ETH1, addr1);
+}
+
+void __init tx4938_mtd_init(int ch)
+{
+	struct physmap_flash_data pdata = {
+		.width = TX4938_EBUSC_WIDTH(ch) / 8,
+	};
+	unsigned long start = txx9_ce_res[ch].start;
+	unsigned long size = txx9_ce_res[ch].end - start + 1;
+
+	if (!(TX4938_EBUSC_CR(ch) & 0x8))
+		return; /* disabled */
+	txx9_physmap_flash_init(ch, start, size, &pdata);
+}
+
+void __init tx4938_ata_init(unsigned int irq, unsigned int shift, int tune)
+{
+	struct platform_device *pdev;
+	struct resource res[] = {
+		{
+			/* .start and .end are filled in later */
+			.flags = IORESOURCE_MEM,
+		}, {
+			.start = irq,
+			.flags = IORESOURCE_IRQ,
+		},
+	};
+	struct tx4938ide_platform_info pdata = {
+		.ioport_shift = shift,
+		/*
+		 * The IDE driver should not change bus timings if other ISA
+		 * devices existed.
+		 */
+		.gbus_clock = tune ? txx9_gbus_clock : 0,
+	};
+	u64 ebccr;
+	int i;
+
+	if ((__raw_readq(&tx4938_ccfgptr->pcfg) &
+	     (TX4938_PCFG_ATA_SEL | TX4938_PCFG_NDF_SEL))
+	    != TX4938_PCFG_ATA_SEL)
+		return;
+	for (i = 0; i < 8; i++) {
+		/* check EBCCRn.ISA, EBCCRn.BSZ, EBCCRn.ME */
+		ebccr = __raw_readq(&tx4938_ebuscptr->cr[i]);
+		if ((ebccr & 0x00f00008) == 0x00e00008)
+			break;
+	}
+	if (i == 8)
+		return;
+	pdata.ebus_ch = i;
+	res[0].start = ((ebccr >> 48) << 20) + 0x10000;
+	res[0].end = res[0].start + 0x20000 - 1;
+	pdev = platform_device_alloc("tx4938ide", -1);
+	if (!pdev ||
+	    platform_device_add_resources(pdev, res, ARRAY_SIZE(res)) ||
+	    platform_device_add_data(pdev, &pdata, sizeof(pdata)) ||
+	    platform_device_add(pdev))
+		platform_device_put(pdev);
+}
+
+void __init tx4938_ndfmc_init(unsigned int hold, unsigned int spw)
+{
+	struct txx9ndfmc_platform_data plat_data = {
+		.shift = 1,
+		.gbus_clock = txx9_gbus_clock,
+		.hold = hold,
+		.spw = spw,
+		.ch_mask = 1,
+	};
+	unsigned long baseaddr = TX4938_NDFMC_REG & 0xfffffffffULL;
+
+#ifdef __BIG_ENDIAN
+	baseaddr += 4;
+#endif
+	if ((__raw_readq(&tx4938_ccfgptr->pcfg) &
+	     (TX4938_PCFG_ATA_SEL|TX4938_PCFG_ISA_SEL|TX4938_PCFG_NDF_SEL)) ==
+	    TX4938_PCFG_NDF_SEL)
+		txx9_ndfmc_init(baseaddr, &plat_data);
+}
+
+void __init tx4938_dmac_init(int memcpy_chan0, int memcpy_chan1)
+{
+	struct txx9dmac_platform_data plat_data = {
+		.have_64bit_regs = true,
+	};
+	int i;
+
+	for (i = 0; i < 2; i++) {
+		plat_data.memcpy_chan = i ? memcpy_chan1 : memcpy_chan0;
+		txx9_dmac_init(i, TX4938_DMA_REG(i) & 0xfffffffffULL,
+			       TXX9_IRQ_BASE + TX4938_IR_DMA(i, 0),
+			       &plat_data);
+	}
+}
+
+void __init tx4938_aclc_init(void)
+{
+	u64 pcfg = __raw_readq(&tx4938_ccfgptr->pcfg);
+
+	if ((pcfg & TX4938_PCFG_SEL2) &&
+	    !(pcfg & TX4938_PCFG_ETH0_SEL))
+		txx9_aclc_init(TX4938_ACLC_REG & 0xfffffffffULL,
+			       TXX9_IRQ_BASE + TX4938_IR_ACLC,
+			       1, 0, 1);
+}
+
+void __init tx4938_sramc_init(void)
+{
+	if (tx4938_sram_resource.start)
+		txx9_sramc_init(&tx4938_sram_resource);
+}
+
+static void __init tx4938_stop_unused_modules(void)
+{
+	__u64 pcfg, rst = 0, ckd = 0;
+	char buf[128];
+
+	buf[0] = '\0';
+	local_irq_disable();
+	pcfg = ____raw_readq(&tx4938_ccfgptr->pcfg);
+	switch (txx9_pcode) {
+	case 0x4937:
+		if (!(pcfg & TX4938_PCFG_SEL2)) {
+			rst |= TX4938_CLKCTR_ACLRST;
+			ckd |= TX4938_CLKCTR_ACLCKD;
+			strcat(buf, " ACLC");
+		}
+		break;
+	case 0x4938:
+		if (!(pcfg & TX4938_PCFG_SEL2) ||
+		    (pcfg & TX4938_PCFG_ETH0_SEL)) {
+			rst |= TX4938_CLKCTR_ACLRST;
+			ckd |= TX4938_CLKCTR_ACLCKD;
+			strcat(buf, " ACLC");
+		}
+		if ((pcfg &
+		     (TX4938_PCFG_ATA_SEL | TX4938_PCFG_ISA_SEL |
+		      TX4938_PCFG_NDF_SEL))
+		    != TX4938_PCFG_NDF_SEL) {
+			rst |= TX4938_CLKCTR_NDFRST;
+			ckd |= TX4938_CLKCTR_NDFCKD;
+			strcat(buf, " NDFMC");
+		}
+		if (!(pcfg & TX4938_PCFG_SPI_SEL)) {
+			rst |= TX4938_CLKCTR_SPIRST;
+			ckd |= TX4938_CLKCTR_SPICKD;
+			strcat(buf, " SPI");
+		}
+		break;
+	}
+	if (rst | ckd) {
+		txx9_set64(&tx4938_ccfgptr->clkctr, rst);
+		txx9_set64(&tx4938_ccfgptr->clkctr, ckd);
+	}
+	local_irq_enable();
+	if (buf[0])
+		pr_info("%s: stop%s\n", txx9_pcode_str, buf);
+}
+
+static int __init tx4938_late_init(void)
+{
+	if (txx9_pcode != 0x4937 && txx9_pcode != 0x4938)
+		return -ENODEV;
+	tx4938_stop_unused_modules();
+	return 0;
+}
+late_initcall(tx4938_late_init);
diff --git a/arch/mips/txx9/generic/smsc_fdc37m81x.c b/arch/mips/txx9/generic/smsc_fdc37m81x.c
new file mode 100644
index 000000000..40f4098d3
--- /dev/null
+++ b/arch/mips/txx9/generic/smsc_fdc37m81x.c
@@ -0,0 +1,169 @@
+/*
+ * Interface for smsc fdc48m81x Super IO chip
+ *
+ * Author: MontaVista Software, Inc. source@mvista.com
+ *
+ * 2001-2003 (c) MontaVista Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ *
+ * Copyright 2004 (c) MontaVista Software, Inc.
+ */
+#include <linux/init.h>
+#include <linux/types.h>
+#include <asm/io.h>
+#include <asm/txx9/smsc_fdc37m81x.h>
+
+/* Common Registers */
+#define SMSC_FDC37M81X_CONFIG_INDEX  0x00
+#define SMSC_FDC37M81X_CONFIG_DATA   0x01
+#define SMSC_FDC37M81X_CONF	     0x02
+#define SMSC_FDC37M81X_INDEX	     0x03
+#define SMSC_FDC37M81X_DNUM	     0x07
+#define SMSC_FDC37M81X_DID	     0x20
+#define SMSC_FDC37M81X_DREV	     0x21
+#define SMSC_FDC37M81X_PCNT	     0x22
+#define SMSC_FDC37M81X_PMGT	     0x23
+#define SMSC_FDC37M81X_OSC	     0x24
+#define SMSC_FDC37M81X_CONFPA0	     0x26
+#define SMSC_FDC37M81X_CONFPA1	     0x27
+#define SMSC_FDC37M81X_TEST4	     0x2B
+#define SMSC_FDC37M81X_TEST5	     0x2C
+#define SMSC_FDC37M81X_TEST1	     0x2D
+#define SMSC_FDC37M81X_TEST2	     0x2E
+#define SMSC_FDC37M81X_TEST3	     0x2F
+
+/* Logical device numbers */
+#define SMSC_FDC37M81X_FDD	     0x00
+#define SMSC_FDC37M81X_SERIAL1	     0x04
+#define SMSC_FDC37M81X_SERIAL2	     0x05
+#define SMSC_FDC37M81X_KBD	     0x07
+
+/* Logical device Config Registers */
+#define SMSC_FDC37M81X_ACTIVE	     0x30
+#define SMSC_FDC37M81X_BASEADDR0     0x60
+#define SMSC_FDC37M81X_BASEADDR1     0x61
+#define SMSC_FDC37M81X_INT	     0x70
+#define SMSC_FDC37M81X_INT2	     0x72
+#define SMSC_FDC37M81X_MODE	     0xF0
+
+/* Chip Config Values */
+#define SMSC_FDC37M81X_CONFIG_ENTER  0x55
+#define SMSC_FDC37M81X_CONFIG_EXIT   0xaa
+#define SMSC_FDC37M81X_CHIP_ID	     0x4d
+
+static unsigned long g_smsc_fdc37m81x_base;
+
+static inline unsigned char smsc_fdc37m81x_rd(unsigned char index)
+{
+	outb(index, g_smsc_fdc37m81x_base + SMSC_FDC37M81X_CONFIG_INDEX);
+
+	return inb(g_smsc_fdc37m81x_base + SMSC_FDC37M81X_CONFIG_DATA);
+}
+
+static inline void smsc_dc37m81x_wr(unsigned char index, unsigned char data)
+{
+	outb(index, g_smsc_fdc37m81x_base + SMSC_FDC37M81X_CONFIG_INDEX);
+	outb(data, g_smsc_fdc37m81x_base + SMSC_FDC37M81X_CONFIG_DATA);
+}
+
+void smsc_fdc37m81x_config_beg(void)
+{
+	if (g_smsc_fdc37m81x_base) {
+		outb(SMSC_FDC37M81X_CONFIG_ENTER,
+		     g_smsc_fdc37m81x_base + SMSC_FDC37M81X_CONFIG_INDEX);
+	}
+}
+
+void smsc_fdc37m81x_config_end(void)
+{
+	if (g_smsc_fdc37m81x_base)
+		outb(SMSC_FDC37M81X_CONFIG_EXIT,
+		     g_smsc_fdc37m81x_base + SMSC_FDC37M81X_CONFIG_INDEX);
+}
+
+u8 smsc_fdc37m81x_config_get(u8 reg)
+{
+	u8 val = 0;
+
+	if (g_smsc_fdc37m81x_base)
+		val = smsc_fdc37m81x_rd(reg);
+
+	return val;
+}
+
+void smsc_fdc37m81x_config_set(u8 reg, u8 val)
+{
+	if (g_smsc_fdc37m81x_base)
+		smsc_dc37m81x_wr(reg, val);
+}
+
+unsigned long __init smsc_fdc37m81x_init(unsigned long port)
+{
+	const int field = sizeof(unsigned long) * 2;
+	u8 chip_id;
+
+	if (g_smsc_fdc37m81x_base)
+		pr_warn("%s: stepping on old base=0x%0*lx\n", __func__, field,
+			g_smsc_fdc37m81x_base);
+
+	g_smsc_fdc37m81x_base = port;
+
+	smsc_fdc37m81x_config_beg();
+
+	chip_id = smsc_fdc37m81x_rd(SMSC_FDC37M81X_DID);
+	if (chip_id == SMSC_FDC37M81X_CHIP_ID)
+		smsc_fdc37m81x_config_end();
+	else {
+		pr_warn("%s: unknown chip id 0x%02x\n", __func__, chip_id);
+		g_smsc_fdc37m81x_base = 0;
+	}
+
+	return g_smsc_fdc37m81x_base;
+}
+
+#ifdef DEBUG
+static void smsc_fdc37m81x_config_dump_one(const char *key, u8 dev, u8 reg)
+{
+	pr_info("%s: dev=0x%02x reg=0x%02x val=0x%02x\n", key, dev, reg,
+		smsc_fdc37m81x_rd(reg));
+}
+
+void smsc_fdc37m81x_config_dump(void)
+{
+	u8 orig;
+	const char *fname = __func__;
+
+	smsc_fdc37m81x_config_beg();
+
+	orig = smsc_fdc37m81x_rd(SMSC_FDC37M81X_DNUM);
+
+	pr_info("%s: common\n", fname);
+	smsc_fdc37m81x_config_dump_one(fname, SMSC_FDC37M81X_NONE,
+				       SMSC_FDC37M81X_DNUM);
+	smsc_fdc37m81x_config_dump_one(fname, SMSC_FDC37M81X_NONE,
+				       SMSC_FDC37M81X_DID);
+	smsc_fdc37m81x_config_dump_one(fname, SMSC_FDC37M81X_NONE,
+				       SMSC_FDC37M81X_DREV);
+	smsc_fdc37m81x_config_dump_one(fname, SMSC_FDC37M81X_NONE,
+				       SMSC_FDC37M81X_PCNT);
+	smsc_fdc37m81x_config_dump_one(fname, SMSC_FDC37M81X_NONE,
+				       SMSC_FDC37M81X_PMGT);
+
+	pr_info("%s: keyboard\n", fname);
+	smsc_dc37m81x_wr(SMSC_FDC37M81X_DNUM, SMSC_FDC37M81X_KBD);
+	smsc_fdc37m81x_config_dump_one(fname, SMSC_FDC37M81X_KBD,
+				       SMSC_FDC37M81X_ACTIVE);
+	smsc_fdc37m81x_config_dump_one(fname, SMSC_FDC37M81X_KBD,
+				       SMSC_FDC37M81X_INT);
+	smsc_fdc37m81x_config_dump_one(fname, SMSC_FDC37M81X_KBD,
+				       SMSC_FDC37M81X_INT2);
+	smsc_fdc37m81x_config_dump_one(fname, SMSC_FDC37M81X_KBD,
+				       SMSC_FDC37M81X_LDCR_F0);
+
+	smsc_dc37m81x_wr(SMSC_FDC37M81X_DNUM, orig);
+
+	smsc_fdc37m81x_config_end();
+}
+#endif
diff --git a/arch/mips/txx9/rbtx4927/Makefile b/arch/mips/txx9/rbtx4927/Makefile
new file mode 100644
index 000000000..08a02aebd
--- /dev/null
+++ b/arch/mips/txx9/rbtx4927/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0-only
+obj-y	+= prom.o setup.o irq.o
diff --git a/arch/mips/txx9/rbtx4927/irq.c b/arch/mips/txx9/rbtx4927/irq.c
new file mode 100644
index 000000000..3f48292c9
--- /dev/null
+++ b/arch/mips/txx9/rbtx4927/irq.c
@@ -0,0 +1,198 @@
+/*
+ * Toshiba RBTX4927 specific interrupt handlers
+ *
+ * Author: MontaVista Software, Inc.
+ *	   source@mvista.com
+ *
+ * Copyright 2001-2002 MontaVista Software Inc.
+ *
+ *  This program is free software; you can redistribute it and/or modify it
+ *  under the terms of the GNU General Public License as published by the
+ *  Free Software Foundation; either version 2 of the License, or (at your
+ *  option) any later version.
+ *
+ *  THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ *  WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
+ *  IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ *  BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ *  OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ *  ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
+ *  TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
+ *  USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the GNU General Public License along
+ *  with this program; if not, write to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+/*
+ * I8259A_IRQ_BASE+00
+ * I8259A_IRQ_BASE+01 PS2/Keyboard
+ * I8259A_IRQ_BASE+02 Cascade RBTX4927-ISA (irqs 8-15)
+ * I8259A_IRQ_BASE+03
+ * I8259A_IRQ_BASE+04
+ * I8259A_IRQ_BASE+05
+ * I8259A_IRQ_BASE+06
+ * I8259A_IRQ_BASE+07
+ * I8259A_IRQ_BASE+08
+ * I8259A_IRQ_BASE+09
+ * I8259A_IRQ_BASE+10
+ * I8259A_IRQ_BASE+11
+ * I8259A_IRQ_BASE+12 PS2/Mouse (not supported at this time)
+ * I8259A_IRQ_BASE+13
+ * I8259A_IRQ_BASE+14 IDE
+ * I8259A_IRQ_BASE+15
+ *
+ * MIPS_CPU_IRQ_BASE+00 Software 0
+ * MIPS_CPU_IRQ_BASE+01 Software 1
+ * MIPS_CPU_IRQ_BASE+02 Cascade TX4927-CP0
+ * MIPS_CPU_IRQ_BASE+03 Multiplexed -- do not use
+ * MIPS_CPU_IRQ_BASE+04 Multiplexed -- do not use
+ * MIPS_CPU_IRQ_BASE+05 Multiplexed -- do not use
+ * MIPS_CPU_IRQ_BASE+06 Multiplexed -- do not use
+ * MIPS_CPU_IRQ_BASE+07 CPU TIMER
+ *
+ * TXX9_IRQ_BASE+00
+ * TXX9_IRQ_BASE+01
+ * TXX9_IRQ_BASE+02
+ * TXX9_IRQ_BASE+03 Cascade RBTX4927-IOC
+ * TXX9_IRQ_BASE+04
+ * TXX9_IRQ_BASE+05 RBTX4927 RTL-8019AS ethernet
+ * TXX9_IRQ_BASE+06
+ * TXX9_IRQ_BASE+07
+ * TXX9_IRQ_BASE+08 TX4927 SerialIO Channel 0
+ * TXX9_IRQ_BASE+09 TX4927 SerialIO Channel 1
+ * TXX9_IRQ_BASE+10
+ * TXX9_IRQ_BASE+11
+ * TXX9_IRQ_BASE+12
+ * TXX9_IRQ_BASE+13
+ * TXX9_IRQ_BASE+14
+ * TXX9_IRQ_BASE+15
+ * TXX9_IRQ_BASE+16 TX4927 PCI PCI-C
+ * TXX9_IRQ_BASE+17
+ * TXX9_IRQ_BASE+18
+ * TXX9_IRQ_BASE+19
+ * TXX9_IRQ_BASE+20
+ * TXX9_IRQ_BASE+21
+ * TXX9_IRQ_BASE+22 TX4927 PCI PCI-ERR
+ * TXX9_IRQ_BASE+23 TX4927 PCI PCI-PMA (not used)
+ * TXX9_IRQ_BASE+24
+ * TXX9_IRQ_BASE+25
+ * TXX9_IRQ_BASE+26
+ * TXX9_IRQ_BASE+27
+ * TXX9_IRQ_BASE+28
+ * TXX9_IRQ_BASE+29
+ * TXX9_IRQ_BASE+30
+ * TXX9_IRQ_BASE+31
+ *
+ * RBTX4927_IRQ_IOC+00 FPCIB0 PCI-D (SouthBridge)
+ * RBTX4927_IRQ_IOC+01 FPCIB0 PCI-C (SouthBridge)
+ * RBTX4927_IRQ_IOC+02 FPCIB0 PCI-B (SouthBridge/IDE/pin=1,INTR)
+ * RBTX4927_IRQ_IOC+03 FPCIB0 PCI-A (SouthBridge/USB/pin=4)
+ * RBTX4927_IRQ_IOC+04
+ * RBTX4927_IRQ_IOC+05
+ * RBTX4927_IRQ_IOC+06
+ * RBTX4927_IRQ_IOC+07
+ *
+ * NOTES:
+ * SouthBridge/INTR is mapped to SouthBridge/A=PCI-B/#58
+ * SouthBridge/ISA/pin=0 no pci irq used by this device
+ * SouthBridge/IDE/pin=1 no pci irq used by this device, using INTR
+ * via ISA IRQ14
+ * SouthBridge/USB/pin=4 using pci irq SouthBridge/D=PCI-A=#59
+ * SouthBridge/PMC/pin=0 no pci irq used by this device
+ * SuperIO/PS2/Keyboard, using INTR via ISA IRQ1
+ * SuperIO/PS2/Mouse, using INTR via ISA IRQ12 (mouse not currently supported)
+ * JP7 is not bus master -- do NOT use -- only 4 pci bus master's
+ * allowed -- SouthBridge, JP4, JP5, JP6
+ */
+
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <asm/io.h>
+#include <asm/mipsregs.h>
+#include <asm/txx9/generic.h>
+#include <asm/txx9/rbtx4927.h>
+
+static int toshiba_rbtx4927_irq_nested(int sw_irq)
+{
+	u8 level3;
+
+	level3 = readb(rbtx4927_imstat_addr) & 0x1f;
+	if (unlikely(!level3))
+		return -1;
+	return RBTX4927_IRQ_IOC + __fls8(level3);
+}
+
+static void toshiba_rbtx4927_irq_ioc_enable(struct irq_data *d)
+{
+	unsigned char v;
+
+	v = readb(rbtx4927_imask_addr);
+	v |= (1 << (d->irq - RBTX4927_IRQ_IOC));
+	writeb(v, rbtx4927_imask_addr);
+}
+
+static void toshiba_rbtx4927_irq_ioc_disable(struct irq_data *d)
+{
+	unsigned char v;
+
+	v = readb(rbtx4927_imask_addr);
+	v &= ~(1 << (d->irq - RBTX4927_IRQ_IOC));
+	writeb(v, rbtx4927_imask_addr);
+	mmiowb();
+}
+
+#define TOSHIBA_RBTX4927_IOC_NAME "RBTX4927-IOC"
+static struct irq_chip toshiba_rbtx4927_irq_ioc_type = {
+	.name = TOSHIBA_RBTX4927_IOC_NAME,
+	.irq_mask = toshiba_rbtx4927_irq_ioc_disable,
+	.irq_unmask = toshiba_rbtx4927_irq_ioc_enable,
+};
+
+static void __init toshiba_rbtx4927_irq_ioc_init(void)
+{
+	int i;
+
+	/* mask all IOC interrupts */
+	writeb(0, rbtx4927_imask_addr);
+	/* clear SoftInt interrupts */
+	writeb(0, rbtx4927_softint_addr);
+
+	for (i = RBTX4927_IRQ_IOC;
+	     i < RBTX4927_IRQ_IOC + RBTX4927_NR_IRQ_IOC; i++)
+		irq_set_chip_and_handler(i, &toshiba_rbtx4927_irq_ioc_type,
+					 handle_level_irq);
+	irq_set_chained_handler(RBTX4927_IRQ_IOCINT, handle_simple_irq);
+}
+
+static int rbtx4927_irq_dispatch(int pending)
+{
+	int irq;
+
+	if (pending & STATUSF_IP7)			/* cpu timer */
+		irq = MIPS_CPU_IRQ_BASE + 7;
+	else if (pending & STATUSF_IP2) {		/* tx4927 pic */
+		irq = txx9_irq();
+		if (irq == RBTX4927_IRQ_IOCINT)
+			irq = toshiba_rbtx4927_irq_nested(irq);
+	} else if (pending & STATUSF_IP0)		/* user line 0 */
+		irq = MIPS_CPU_IRQ_BASE + 0;
+	else if (pending & STATUSF_IP1)			/* user line 1 */
+		irq = MIPS_CPU_IRQ_BASE + 1;
+	else
+		irq = -1;
+	return irq;
+}
+
+void __init rbtx4927_irq_setup(void)
+{
+	txx9_irq_dispatch = rbtx4927_irq_dispatch;
+	tx4927_irq_init();
+	toshiba_rbtx4927_irq_ioc_init();
+	/* Onboard 10M Ether: High Active */
+	irq_set_irq_type(RBTX4927_RTL_8019_IRQ, IRQF_TRIGGER_HIGH);
+}
diff --git a/arch/mips/txx9/rbtx4927/prom.c b/arch/mips/txx9/rbtx4927/prom.c
new file mode 100644
index 000000000..9b4acff82
--- /dev/null
+++ b/arch/mips/txx9/rbtx4927/prom.c
@@ -0,0 +1,42 @@
+/*
+ * rbtx4927 specific prom routines
+ *
+ * Author: MontaVista Software, Inc.
+ *	   source@mvista.com
+ *
+ * Copyright 2001-2002 MontaVista Software Inc.
+ *
+ * Copyright (C) 2004 MontaVista Software Inc.
+ * Author: Manish Lachwani, mlachwani@mvista.com
+ *
+ *  This program is free software; you can redistribute it and/or modify it
+ *  under the terms of the GNU General Public License as published by the
+ *  Free Software Foundation; either version 2 of the License, or (at your
+ *  option) any later version.
+ *
+ *  THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ *  WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
+ *  IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ *  BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ *  OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ *  ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
+ *  TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
+ *  USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the GNU General Public License along
+ *  with this program; if not, write to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/init.h>
+#include <linux/memblock.h>
+#include <asm/txx9/generic.h>
+#include <asm/txx9/rbtx4927.h>
+
+void __init rbtx4927_prom_init(void)
+{
+	memblock_add(0, tx4927_get_mem_size());
+	txx9_sio_putchar_init(TX4927_SIO_REG(0) & 0xfffffffffULL);
+}
diff --git a/arch/mips/txx9/rbtx4927/setup.c b/arch/mips/txx9/rbtx4927/setup.c
new file mode 100644
index 000000000..31955c1d5
--- /dev/null
+++ b/arch/mips/txx9/rbtx4927/setup.c
@@ -0,0 +1,380 @@
+/*
+ * Toshiba rbtx4927 specific setup
+ *
+ * Author: MontaVista Software, Inc.
+ *	   source@mvista.com
+ *
+ * Copyright 2001-2002 MontaVista Software Inc.
+ *
+ * Copyright (C) 1996, 97, 2001, 04  Ralf Baechle (ralf@linux-mips.org)
+ * Copyright (C) 2000 RidgeRun, Inc.
+ * Author: RidgeRun, Inc.
+ *   glonnon@ridgerun.com, skranz@ridgerun.com, stevej@ridgerun.com
+ *
+ * Copyright 2001 MontaVista Software Inc.
+ * Author: jsun@mvista.com or jsun@junsun.net
+ *
+ * Copyright 2002 MontaVista Software Inc.
+ * Author: Michael Pruznick, michael_pruznick@mvista.com
+ *
+ * Copyright (C) 2000-2001 Toshiba Corporation
+ *
+ * Copyright (C) 2004 MontaVista Software Inc.
+ * Author: Manish Lachwani, mlachwani@mvista.com
+ *
+ *  This program is free software; you can redistribute it and/or modify it
+ *  under the terms of the GNU General Public License as published by the
+ *  Free Software Foundation; either version 2 of the License, or (at your
+ *  option) any later version.
+ *
+ *  THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ *  WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
+ *  IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ *  BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ *  OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
+ *  ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
+ *  TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
+ *  USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the GNU General Public License along
+ *  with this program; if not, write to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/ioport.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/gpio.h>
+#include <linux/leds.h>
+#include <asm/io.h>
+#include <asm/reboot.h>
+#include <asm/txx9pio.h>
+#include <asm/txx9/generic.h>
+#include <asm/txx9/pci.h>
+#include <asm/txx9/rbtx4927.h>
+#include <asm/txx9/tx4938.h>	/* for TX4937 */
+
+#ifdef CONFIG_PCI
+static void __init tx4927_pci_setup(void)
+{
+	int extarb = !(__raw_readq(&tx4927_ccfgptr->ccfg) & TX4927_CCFG_PCIARB);
+	struct pci_controller *c = &txx9_primary_pcic;
+
+	register_pci_controller(c);
+
+	if (__raw_readq(&tx4927_ccfgptr->ccfg) & TX4927_CCFG_PCI66)
+		txx9_pci_option =
+			(txx9_pci_option & ~TXX9_PCI_OPT_CLK_MASK) |
+			TXX9_PCI_OPT_CLK_66; /* already configured */
+
+	/* Reset PCI Bus */
+	writeb(1, rbtx4927_pcireset_addr);
+	/* Reset PCIC */
+	txx9_set64(&tx4927_ccfgptr->clkctr, TX4927_CLKCTR_PCIRST);
+	if ((txx9_pci_option & TXX9_PCI_OPT_CLK_MASK) ==
+	    TXX9_PCI_OPT_CLK_66)
+		tx4927_pciclk66_setup();
+	mdelay(10);
+	/* clear PCIC reset */
+	txx9_clear64(&tx4927_ccfgptr->clkctr, TX4927_CLKCTR_PCIRST);
+	writeb(0, rbtx4927_pcireset_addr);
+	iob();
+
+	tx4927_report_pciclk();
+	tx4927_pcic_setup(tx4927_pcicptr, c, extarb);
+	if ((txx9_pci_option & TXX9_PCI_OPT_CLK_MASK) ==
+	    TXX9_PCI_OPT_CLK_AUTO &&
+	    txx9_pci66_check(c, 0, 0)) {
+		/* Reset PCI Bus */
+		writeb(1, rbtx4927_pcireset_addr);
+		/* Reset PCIC */
+		txx9_set64(&tx4927_ccfgptr->clkctr, TX4927_CLKCTR_PCIRST);
+		tx4927_pciclk66_setup();
+		mdelay(10);
+		/* clear PCIC reset */
+		txx9_clear64(&tx4927_ccfgptr->clkctr, TX4927_CLKCTR_PCIRST);
+		writeb(0, rbtx4927_pcireset_addr);
+		iob();
+		/* Reinitialize PCIC */
+		tx4927_report_pciclk();
+		tx4927_pcic_setup(tx4927_pcicptr, c, extarb);
+	}
+	tx4927_setup_pcierr_irq();
+}
+
+static void __init tx4937_pci_setup(void)
+{
+	int extarb = !(__raw_readq(&tx4938_ccfgptr->ccfg) & TX4938_CCFG_PCIARB);
+	struct pci_controller *c = &txx9_primary_pcic;
+
+	register_pci_controller(c);
+
+	if (__raw_readq(&tx4938_ccfgptr->ccfg) & TX4938_CCFG_PCI66)
+		txx9_pci_option =
+			(txx9_pci_option & ~TXX9_PCI_OPT_CLK_MASK) |
+			TXX9_PCI_OPT_CLK_66; /* already configured */
+
+	/* Reset PCI Bus */
+	writeb(1, rbtx4927_pcireset_addr);
+	/* Reset PCIC */
+	txx9_set64(&tx4938_ccfgptr->clkctr, TX4938_CLKCTR_PCIRST);
+	if ((txx9_pci_option & TXX9_PCI_OPT_CLK_MASK) ==
+	    TXX9_PCI_OPT_CLK_66)
+		tx4938_pciclk66_setup();
+	mdelay(10);
+	/* clear PCIC reset */
+	txx9_clear64(&tx4938_ccfgptr->clkctr, TX4938_CLKCTR_PCIRST);
+	writeb(0, rbtx4927_pcireset_addr);
+	iob();
+
+	tx4938_report_pciclk();
+	tx4927_pcic_setup(tx4938_pcicptr, c, extarb);
+	if ((txx9_pci_option & TXX9_PCI_OPT_CLK_MASK) ==
+	    TXX9_PCI_OPT_CLK_AUTO &&
+	    txx9_pci66_check(c, 0, 0)) {
+		/* Reset PCI Bus */
+		writeb(1, rbtx4927_pcireset_addr);
+		/* Reset PCIC */
+		txx9_set64(&tx4938_ccfgptr->clkctr, TX4938_CLKCTR_PCIRST);
+		tx4938_pciclk66_setup();
+		mdelay(10);
+		/* clear PCIC reset */
+		txx9_clear64(&tx4938_ccfgptr->clkctr, TX4938_CLKCTR_PCIRST);
+		writeb(0, rbtx4927_pcireset_addr);
+		iob();
+		/* Reinitialize PCIC */
+		tx4938_report_pciclk();
+		tx4927_pcic_setup(tx4938_pcicptr, c, extarb);
+	}
+	tx4938_setup_pcierr_irq();
+}
+#else
+static inline void tx4927_pci_setup(void) {}
+static inline void tx4937_pci_setup(void) {}
+#endif /* CONFIG_PCI */
+
+static void __init rbtx4927_gpio_init(void)
+{
+	/* TX4927-SIO DTR on (PIO[15]) */
+	gpio_request(15, "sio-dtr");
+	gpio_direction_output(15, 1);
+
+	tx4927_sio_init(0, 0);
+}
+
+static void __init rbtx4927_arch_init(void)
+{
+	txx9_gpio_init(TX4927_PIO_REG & 0xfffffffffULL, 0, TX4927_NUM_PIO);
+
+	rbtx4927_gpio_init();
+
+	tx4927_pci_setup();
+}
+
+static void __init rbtx4937_arch_init(void)
+{
+	txx9_gpio_init(TX4938_PIO_REG & 0xfffffffffULL, 0, TX4938_NUM_PIO);
+
+	rbtx4927_gpio_init();
+
+	tx4937_pci_setup();
+}
+
+static void toshiba_rbtx4927_restart(char *command)
+{
+	/* enable the s/w reset register */
+	writeb(1, rbtx4927_softresetlock_addr);
+
+	/* wait for enable to be seen */
+	while (!(readb(rbtx4927_softresetlock_addr) & 1))
+		;
+
+	/* do a s/w reset */
+	writeb(1, rbtx4927_softreset_addr);
+
+	/* fallback */
+	(*_machine_halt)();
+}
+
+static void __init rbtx4927_clock_init(void);
+static void __init rbtx4937_clock_init(void);
+
+static void __init rbtx4927_mem_setup(void)
+{
+	if (TX4927_REV_PCODE() == 0x4927) {
+		rbtx4927_clock_init();
+		tx4927_setup();
+	} else {
+		rbtx4937_clock_init();
+		tx4938_setup();
+	}
+
+	_machine_restart = toshiba_rbtx4927_restart;
+
+#ifdef CONFIG_PCI
+	txx9_alloc_pci_controller(&txx9_primary_pcic,
+				  RBTX4927_PCIMEM, RBTX4927_PCIMEM_SIZE,
+				  RBTX4927_PCIIO, RBTX4927_PCIIO_SIZE);
+	txx9_board_pcibios_setup = tx4927_pcibios_setup;
+#else
+	set_io_port_base(KSEG1 + RBTX4927_ISA_IO_OFFSET);
+#endif
+}
+
+static void __init rbtx4927_clock_init(void)
+{
+	/*
+	 * ASSUMPTION: PCIDIVMODE is configured for PCI 33MHz or 66MHz.
+	 *
+	 * For TX4927:
+	 * PCIDIVMODE[12:11]'s initial value is given by S9[4:3] (ON:0, OFF:1).
+	 * CPU 166MHz: PCI 66MHz : PCIDIVMODE: 00 (1/2.5)
+	 * CPU 200MHz: PCI 66MHz : PCIDIVMODE: 01 (1/3)
+	 * CPU 166MHz: PCI 33MHz : PCIDIVMODE: 10 (1/5)
+	 * CPU 200MHz: PCI 33MHz : PCIDIVMODE: 11 (1/6)
+	 * i.e. S9[3]: ON (83MHz), OFF (100MHz)
+	 */
+	switch ((unsigned long)__raw_readq(&tx4927_ccfgptr->ccfg) &
+		TX4927_CCFG_PCIDIVMODE_MASK) {
+	case TX4927_CCFG_PCIDIVMODE_2_5:
+	case TX4927_CCFG_PCIDIVMODE_5:
+		txx9_cpu_clock = 166666666;	/* 166MHz */
+		break;
+	default:
+		txx9_cpu_clock = 200000000;	/* 200MHz */
+	}
+}
+
+static void __init rbtx4937_clock_init(void)
+{
+	/*
+	 * ASSUMPTION: PCIDIVMODE is configured for PCI 33MHz or 66MHz.
+	 *
+	 * For TX4937:
+	 * PCIDIVMODE[12:11]'s initial value is given by S1[5:4] (ON:0, OFF:1)
+	 * PCIDIVMODE[10] is 0.
+	 * CPU 266MHz: PCI 33MHz : PCIDIVMODE: 000 (1/8)
+	 * CPU 266MHz: PCI 66MHz : PCIDIVMODE: 001 (1/4)
+	 * CPU 300MHz: PCI 33MHz : PCIDIVMODE: 010 (1/9)
+	 * CPU 300MHz: PCI 66MHz : PCIDIVMODE: 011 (1/4.5)
+	 * CPU 333MHz: PCI 33MHz : PCIDIVMODE: 100 (1/10)
+	 * CPU 333MHz: PCI 66MHz : PCIDIVMODE: 101 (1/5)
+	 */
+	switch ((unsigned long)__raw_readq(&tx4938_ccfgptr->ccfg) &
+		TX4938_CCFG_PCIDIVMODE_MASK) {
+	case TX4938_CCFG_PCIDIVMODE_8:
+	case TX4938_CCFG_PCIDIVMODE_4:
+		txx9_cpu_clock = 266666666;	/* 266MHz */
+		break;
+	case TX4938_CCFG_PCIDIVMODE_9:
+	case TX4938_CCFG_PCIDIVMODE_4_5:
+		txx9_cpu_clock = 300000000;	/* 300MHz */
+		break;
+	default:
+		txx9_cpu_clock = 333333333;	/* 333MHz */
+	}
+}
+
+static void __init rbtx4927_time_init(void)
+{
+	tx4927_time_init(0);
+}
+
+static void __init toshiba_rbtx4927_rtc_init(void)
+{
+	struct resource res = {
+		.start	= RBTX4927_BRAMRTC_BASE - IO_BASE,
+		.end	= RBTX4927_BRAMRTC_BASE - IO_BASE + 0x800 - 1,
+		.flags	= IORESOURCE_MEM,
+	};
+	platform_device_register_simple("rtc-ds1742", -1, &res, 1);
+}
+
+static void __init rbtx4927_ne_init(void)
+{
+	struct resource res[] = {
+		{
+			.start	= RBTX4927_RTL_8019_BASE,
+			.end	= RBTX4927_RTL_8019_BASE + 0x20 - 1,
+			.flags	= IORESOURCE_IO,
+		}, {
+			.start	= RBTX4927_RTL_8019_IRQ,
+			.flags	= IORESOURCE_IRQ,
+		}
+	};
+	platform_device_register_simple("ne", -1, res, ARRAY_SIZE(res));
+}
+
+static void __init rbtx4927_mtd_init(void)
+{
+	int i;
+
+	for (i = 0; i < 2; i++)
+		tx4927_mtd_init(i);
+}
+
+static void __init rbtx4927_gpioled_init(void)
+{
+	static const struct gpio_led leds[] = {
+		{ .name = "gpioled:green:0", .gpio = 0, .active_low = 1, },
+		{ .name = "gpioled:green:1", .gpio = 1, .active_low = 1, },
+	};
+	static struct gpio_led_platform_data pdata = {
+		.num_leds = ARRAY_SIZE(leds),
+		.leds = leds,
+	};
+	struct platform_device *pdev = platform_device_alloc("leds-gpio", 0);
+
+	if (!pdev)
+		return;
+	pdev->dev.platform_data = &pdata;
+	if (platform_device_add(pdev))
+		platform_device_put(pdev);
+}
+
+static void __init rbtx4927_device_init(void)
+{
+	toshiba_rbtx4927_rtc_init();
+	rbtx4927_ne_init();
+	tx4927_wdt_init();
+	rbtx4927_mtd_init();
+	if (TX4927_REV_PCODE() == 0x4927) {
+		tx4927_dmac_init(2);
+		tx4927_aclc_init(0, 1);
+	} else {
+		tx4938_dmac_init(0, 2);
+		tx4938_aclc_init();
+	}
+	platform_device_register_simple("txx9aclc-generic", -1, NULL, 0);
+	txx9_iocled_init(RBTX4927_LED_ADDR - IO_BASE, -1, 3, 1, "green", NULL);
+	rbtx4927_gpioled_init();
+}
+
+struct txx9_board_vec rbtx4927_vec __initdata = {
+	.system = "Toshiba RBTX4927",
+	.prom_init = rbtx4927_prom_init,
+	.mem_setup = rbtx4927_mem_setup,
+	.irq_setup = rbtx4927_irq_setup,
+	.time_init = rbtx4927_time_init,
+	.device_init = rbtx4927_device_init,
+	.arch_init = rbtx4927_arch_init,
+#ifdef CONFIG_PCI
+	.pci_map_irq = rbtx4927_pci_map_irq,
+#endif
+};
+struct txx9_board_vec rbtx4937_vec __initdata = {
+	.system = "Toshiba RBTX4937",
+	.prom_init = rbtx4927_prom_init,
+	.mem_setup = rbtx4927_mem_setup,
+	.irq_setup = rbtx4927_irq_setup,
+	.time_init = rbtx4927_time_init,
+	.device_init = rbtx4927_device_init,
+	.arch_init = rbtx4937_arch_init,
+#ifdef CONFIG_PCI
+	.pci_map_irq = rbtx4927_pci_map_irq,
+#endif
+};
diff --git a/arch/mips/vdso/.gitignore b/arch/mips/vdso/.gitignore
new file mode 100644
index 000000000..1f43f6dd8
--- /dev/null
+++ b/arch/mips/vdso/.gitignore
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0-only
+*.so*
+vdso-*image.c
+genvdso
+vdso*.lds
diff --git a/arch/mips/vdso/Kconfig b/arch/mips/vdso/Kconfig
new file mode 100644
index 000000000..a665f6108
--- /dev/null
+++ b/arch/mips/vdso/Kconfig
@@ -0,0 +1,18 @@
+# For the pre-R6 code in arch/mips/vdso/vdso.h for locating
+# the base address of VDSO, the linker will emit a R_MIPS_PC32
+# relocation in binutils > 2.25 but it will fail with older versions
+# because that relocation is not supported for that symbol. As a result
+# of which we are forced to disable the VDSO symbols when building
+# with < 2.25 binutils on pre-R6 kernels. For more references on why we
+# can't use other methods to get the base address of VDSO please refer to
+# the comments on that file.
+#
+# GCC (at least up to version 9.2) appears to emit function calls that make use
+# of the GOT when targeting microMIPS, which we can't use in the VDSO due to
+# the lack of relocations. As such, we disable the VDSO for microMIPS builds.
+
+config MIPS_LD_CAN_LINK_VDSO
+	def_bool LD_VERSION >= 22500 || LD_IS_LLD
+
+config MIPS_DISABLE_VDSO
+	def_bool CPU_MICROMIPS || (!CPU_MIPSR6 && !MIPS_LD_CAN_LINK_VDSO)
diff --git a/arch/mips/vdso/Makefile b/arch/mips/vdso/Makefile
new file mode 100644
index 000000000..1f7d5c6c1
--- /dev/null
+++ b/arch/mips/vdso/Makefile
@@ -0,0 +1,211 @@
+# SPDX-License-Identifier: GPL-2.0
+# Objects to go into the VDSO.
+
+# Sanitizer runtimes are unavailable and cannot be linked here.
+ KCSAN_SANITIZE			:= n
+
+# Absolute relocation type $(ARCH_REL_TYPE_ABS) needs to be defined before
+# the inclusion of generic Makefile.
+ARCH_REL_TYPE_ABS := R_MIPS_JUMP_SLOT|R_MIPS_GLOB_DAT
+include $(srctree)/lib/vdso/Makefile
+
+obj-vdso-y := elf.o vgettimeofday.o sigreturn.o
+
+# Common compiler flags between ABIs.
+ccflags-vdso := \
+	$(filter -I%,$(KBUILD_CFLAGS)) \
+	$(filter -E%,$(KBUILD_CFLAGS)) \
+	$(filter -mmicromips,$(KBUILD_CFLAGS)) \
+	$(filter -march=%,$(KBUILD_CFLAGS)) \
+	$(filter -m%-float,$(KBUILD_CFLAGS)) \
+	$(filter -mno-loongson-%,$(KBUILD_CFLAGS)) \
+	$(CLANG_FLAGS) \
+	-D__VDSO__
+
+ifndef CONFIG_64BIT
+ccflags-vdso += -DBUILD_VDSO32
+endif
+
+#
+# The -fno-jump-tables flag only prevents the compiler from generating
+# jump tables but does not prevent the compiler from emitting absolute
+# offsets.
+cflags-vdso := $(ccflags-vdso) \
+	$(filter -W%,$(filter-out -Wa$(comma)%,$(KBUILD_CFLAGS))) \
+	-O3 -g -fPIC -fno-strict-aliasing -fno-common -fno-builtin -G 0 \
+	-mrelax-pic-calls $(call cc-option, -mexplicit-relocs) \
+	-fno-stack-protector -fno-jump-tables -DDISABLE_BRANCH_PROFILING \
+	$(call cc-option, -fno-asynchronous-unwind-tables)
+aflags-vdso := $(ccflags-vdso) \
+	-D__ASSEMBLY__ -Wa,-gdwarf-2
+
+ifneq ($(c-gettimeofday-y),)
+CFLAGS_vgettimeofday.o = -include $(c-gettimeofday-y)
+
+# config-n32-o32-env.c prepares the environment to build a 32bit vDSO
+# library on a 64bit kernel.
+# Note: Needs to be included before than the generic library.
+CFLAGS_vgettimeofday-o32.o = -include $(srctree)/$(src)/config-n32-o32-env.c -include $(c-gettimeofday-y)
+CFLAGS_vgettimeofday-n32.o = -include $(srctree)/$(src)/config-n32-o32-env.c -include $(c-gettimeofday-y)
+endif
+
+CFLAGS_REMOVE_vgettimeofday.o = $(CC_FLAGS_FTRACE)
+
+ifdef CONFIG_MIPS_DISABLE_VDSO
+  ifndef CONFIG_MIPS_LD_CAN_LINK_VDSO
+    $(warning MIPS VDSO requires binutils >= 2.25)
+  endif
+  obj-vdso-y := $(filter-out vgettimeofday.o, $(obj-vdso-y))
+endif
+
+# VDSO linker flags.
+ldflags-y := -Bsymbolic --no-undefined -soname=linux-vdso.so.1 \
+	$(filter -E%,$(KBUILD_CFLAGS)) -shared \
+	-G 0 --eh-frame-hdr --hash-style=sysv --build-id=sha1 -T
+
+CFLAGS_REMOVE_vdso.o = $(CC_FLAGS_FTRACE)
+
+GCOV_PROFILE := n
+UBSAN_SANITIZE := n
+KCOV_INSTRUMENT := n
+
+# Check that we don't have PIC 'jalr t9' calls left
+quiet_cmd_vdso_mips_check = VDSOCHK $@
+      cmd_vdso_mips_check = if $(OBJDUMP) --disassemble $@ | grep -E -h "jalr.*t9" > /dev/null; \
+		       then (echo >&2 "$@: PIC 'jalr t9' calls are not supported"; \
+			     rm -f $@; /bin/false); fi
+
+#
+# Shared build commands.
+#
+
+quiet_cmd_vdsold_and_vdso_check = LD      $@
+      cmd_vdsold_and_vdso_check = $(cmd_ld); $(cmd_vdso_check); $(cmd_vdso_mips_check)
+
+quiet_cmd_vdsoas_o_S = AS      $@
+      cmd_vdsoas_o_S = $(CC) $(a_flags) -c -o $@ $<
+
+# Strip rule for the raw .so files
+$(obj)/%.so.raw: OBJCOPYFLAGS := -S
+$(obj)/%.so.raw: $(obj)/%.so.dbg.raw FORCE
+	$(call if_changed,objcopy)
+
+hostprogs := genvdso
+
+quiet_cmd_genvdso = GENVDSO $@
+define cmd_genvdso
+	$(foreach file,$(filter %.raw,$^),cp $(file) $(file:%.raw=%) &&) \
+	$(obj)/genvdso $(<:%.raw=%) $(<:%.dbg.raw=%) $@ $(VDSO_NAME)
+endef
+
+#
+# Build native VDSO.
+#
+
+native-abi := $(filter -mabi=%,$(KBUILD_CFLAGS))
+
+targets += $(obj-vdso-y)
+targets += vdso.lds
+targets += vdso.so.dbg.raw vdso.so.raw
+targets += vdso.so.dbg vdso.so
+targets += vdso-image.c
+
+obj-vdso := $(obj-vdso-y:%.o=$(obj)/%.o)
+
+$(obj-vdso): KBUILD_CFLAGS := $(cflags-vdso) $(native-abi)
+$(obj-vdso): KBUILD_AFLAGS := $(aflags-vdso) $(native-abi)
+
+$(obj)/vdso.lds: KBUILD_CPPFLAGS := $(ccflags-vdso) $(native-abi)
+
+$(obj)/vdso.so.dbg.raw: $(obj)/vdso.lds $(obj-vdso) FORCE
+	$(call if_changed,vdsold_and_vdso_check)
+
+$(obj)/vdso-image.c: $(obj)/vdso.so.dbg.raw $(obj)/vdso.so.raw \
+                     $(obj)/genvdso FORCE
+	$(call if_changed,genvdso)
+
+obj-y += vdso-image.o
+
+#
+# Build O32 VDSO.
+#
+
+# Define these outside the ifdef to ensure they are picked up by clean.
+targets += $(obj-vdso-y:%.o=%-o32.o)
+targets += vdso-o32.lds
+targets += vdso-o32.so.dbg.raw vdso-o32.so.raw
+targets += vdso-o32.so.dbg vdso-o32.so
+targets += vdso-o32-image.c
+
+ifdef CONFIG_MIPS32_O32
+
+obj-vdso-o32 := $(obj-vdso-y:%.o=$(obj)/%-o32.o)
+
+$(obj-vdso-o32): KBUILD_CFLAGS := $(cflags-vdso) -mabi=32
+$(obj-vdso-o32): KBUILD_AFLAGS := $(aflags-vdso) -mabi=32
+
+$(obj)/%-o32.o: $(src)/%.S FORCE
+	$(call if_changed_dep,vdsoas_o_S)
+
+$(obj)/%-o32.o: $(src)/%.c FORCE
+	$(call cmd,force_checksrc)
+	$(call if_changed_rule,cc_o_c)
+
+$(obj)/vdso-o32.lds: KBUILD_CPPFLAGS := $(ccflags-vdso) -mabi=32
+$(obj)/vdso-o32.lds: $(src)/vdso.lds.S FORCE
+	$(call if_changed_dep,cpp_lds_S)
+
+$(obj)/vdso-o32.so.dbg.raw: $(obj)/vdso-o32.lds $(obj-vdso-o32) FORCE
+	$(call if_changed,vdsold_and_vdso_check)
+
+$(obj)/vdso-o32-image.c: VDSO_NAME := o32
+$(obj)/vdso-o32-image.c: $(obj)/vdso-o32.so.dbg.raw $(obj)/vdso-o32.so.raw \
+                         $(obj)/genvdso FORCE
+	$(call if_changed,genvdso)
+
+obj-y += vdso-o32-image.o
+
+endif
+
+#
+# Build N32 VDSO.
+#
+
+targets += $(obj-vdso-y:%.o=%-n32.o)
+targets += vdso-n32.lds
+targets += vdso-n32.so.dbg.raw vdso-n32.so.raw
+targets += vdso-n32.so.dbg vdso-n32.so
+targets += vdso-n32-image.c
+
+ifdef CONFIG_MIPS32_N32
+
+obj-vdso-n32 := $(obj-vdso-y:%.o=$(obj)/%-n32.o)
+
+$(obj-vdso-n32): KBUILD_CFLAGS := $(cflags-vdso) -mabi=n32
+$(obj-vdso-n32): KBUILD_AFLAGS := $(aflags-vdso) -mabi=n32
+
+$(obj)/%-n32.o: $(src)/%.S FORCE
+	$(call if_changed_dep,vdsoas_o_S)
+
+$(obj)/%-n32.o: $(src)/%.c FORCE
+	$(call cmd,force_checksrc)
+	$(call if_changed_rule,cc_o_c)
+
+$(obj)/vdso-n32.lds: KBUILD_CPPFLAGS := $(ccflags-vdso) -mabi=n32
+$(obj)/vdso-n32.lds: $(src)/vdso.lds.S FORCE
+	$(call if_changed_dep,cpp_lds_S)
+
+$(obj)/vdso-n32.so.dbg.raw: $(obj)/vdso-n32.lds $(obj-vdso-n32) FORCE
+	$(call if_changed,vdsold_and_vdso_check)
+
+$(obj)/vdso-n32-image.c: VDSO_NAME := n32
+$(obj)/vdso-n32-image.c: $(obj)/vdso-n32.so.dbg.raw $(obj)/vdso-n32.so.raw \
+                         $(obj)/genvdso FORCE
+	$(call if_changed,genvdso)
+
+obj-y += vdso-n32-image.o
+
+endif
+
+# FIXME: Need install rule for debug.
+# Needs to deal with dependency for generation of dbg by cmd_genvdso...
diff --git a/arch/mips/vdso/config-n32-o32-env.c b/arch/mips/vdso/config-n32-o32-env.c
new file mode 100644
index 000000000..0011a632a
--- /dev/null
+++ b/arch/mips/vdso/config-n32-o32-env.c
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Configuration file for O32 and N32 binaries.
+ * Note: To be included before lib/vdso/gettimeofday.c
+ */
+#if defined(CONFIG_MIPS32_O32) || defined(CONFIG_MIPS32_N32)
+/*
+ * In case of a 32 bit VDSO for a 64 bit kernel fake a 32 bit kernel
+ * configuration.
+ */
+#undef CONFIG_64BIT
+
+#define BUILD_VDSO32
+#define CONFIG_32BIT 1
+#define CONFIG_GENERIC_ATOMIC64 1
+#define BUILD_VDSO32_64
+
+#endif
+
diff --git a/arch/mips/vdso/elf.S b/arch/mips/vdso/elf.S
new file mode 100644
index 000000000..a25cb147f
--- /dev/null
+++ b/arch/mips/vdso/elf.S
@@ -0,0 +1,62 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2015 Imagination Technologies
+ * Author: Alex Smith <alex.smith@imgtec.com>
+ */
+
+#include <asm/vdso/vdso.h>
+
+#include <asm/isa-rev.h>
+
+#include <linux/elfnote.h>
+#include <linux/version.h>
+
+ELFNOTE_START(Linux, 0, "a")
+	.long LINUX_VERSION_CODE
+ELFNOTE_END
+
+/*
+ * The .MIPS.abiflags section must be defined with the FP ABI flags set
+ * to 'any' to be able to link with both old and new libraries.
+ * Newer toolchains are capable of automatically generating this, but we want
+ * to work with older toolchains as well. Therefore, we define the contents of
+ * this section here (under different names), and then genvdso will patch
+ * it to have the correct name and type.
+ *
+ * We base the .MIPS.abiflags section on preprocessor definitions rather than
+ * CONFIG_* because we need to match the particular ABI we are building the
+ * VDSO for.
+ *
+ * See https://dmz-portal.mips.com/wiki/MIPS_O32_ABI_-_FR0_and_FR1_Interlinking
+ * for the .MIPS.abiflags section description.
+ */
+
+	.section .mips_abiflags, "a"
+	.align 3
+__mips_abiflags:
+	.hword	0		/* version */
+	.byte	__mips		/* isa_level */
+
+	/* isa_rev */
+	.byte	MIPS_ISA_REV
+
+	/* gpr_size */
+#ifdef __mips64
+	.byte	2		/* AFL_REG_64 */
+#else
+	.byte	1		/* AFL_REG_32 */
+#endif
+
+	/* cpr1_size */
+#if (MIPS_ISA_REV >= 6) || defined(__mips64)
+	.byte	2		/* AFL_REG_64 */
+#else
+	.byte	1		/* AFL_REG_32 */
+#endif
+
+	.byte	0		/* cpr2_size (AFL_REG_NONE) */
+	.byte	0		/* fp_abi (Val_GNU_MIPS_ABI_FP_ANY) */
+	.word	0		/* isa_ext */
+	.word	0		/* ases */
+	.word	0		/* flags1 */
+	.word	0		/* flags2 */
diff --git a/arch/mips/vdso/genvdso.c b/arch/mips/vdso/genvdso.c
new file mode 100644
index 000000000..09e30eb4b
--- /dev/null
+++ b/arch/mips/vdso/genvdso.c
@@ -0,0 +1,308 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2015 Imagination Technologies
+ * Author: Alex Smith <alex.smith@imgtec.com>
+ */
+
+/*
+ * This tool is used to generate the real VDSO images from the raw image. It
+ * first patches up the MIPS ABI flags and GNU attributes sections defined in
+ * elf.S to have the correct name and type. It then generates a C source file
+ * to be compiled into the kernel containing the VDSO image data and a
+ * mips_vdso_image struct for it, including symbol offsets extracted from the
+ * image.
+ *
+ * We need to be passed both a stripped and unstripped VDSO image. The stripped
+ * image is compiled into the kernel, but we must also patch up the unstripped
+ * image's ABI flags sections so that it can be installed and used for
+ * debugging.
+ */
+
+#include <sys/mman.h>
+#include <sys/stat.h>
+#include <sys/types.h>
+
+#include <byteswap.h>
+#include <elf.h>
+#include <errno.h>
+#include <fcntl.h>
+#include <inttypes.h>
+#include <stdarg.h>
+#include <stdbool.h>
+#include <stdio.h>
+#include <stdlib.h>
+#include <string.h>
+#include <unistd.h>
+
+/* Define these in case the system elf.h is not new enough to have them. */
+#ifndef SHT_GNU_ATTRIBUTES
+# define SHT_GNU_ATTRIBUTES	0x6ffffff5
+#endif
+#ifndef SHT_MIPS_ABIFLAGS
+# define SHT_MIPS_ABIFLAGS	0x7000002a
+#endif
+
+enum {
+	ABI_O32 = (1 << 0),
+	ABI_N32 = (1 << 1),
+	ABI_N64 = (1 << 2),
+
+	ABI_ALL = ABI_O32 | ABI_N32 | ABI_N64,
+};
+
+/* Symbols the kernel requires offsets for. */
+static struct {
+	const char *name;
+	const char *offset_name;
+	unsigned int abis;
+} vdso_symbols[] = {
+	{ "__vdso_sigreturn", "off_sigreturn", ABI_O32 },
+	{ "__vdso_rt_sigreturn", "off_rt_sigreturn", ABI_ALL },
+	{}
+};
+
+static const char *program_name;
+static const char *vdso_name;
+static unsigned char elf_class;
+static unsigned int elf_abi;
+static bool need_swap;
+static FILE *out_file;
+
+#if __BYTE_ORDER__ == __ORDER_LITTLE_ENDIAN__
+# define HOST_ORDER		ELFDATA2LSB
+#elif __BYTE_ORDER__ == __ORDER_BIG_ENDIAN__
+# define HOST_ORDER		ELFDATA2MSB
+#endif
+
+#define BUILD_SWAP(bits)						\
+	static uint##bits##_t swap_uint##bits(uint##bits##_t val)	\
+	{								\
+		return need_swap ? bswap_##bits(val) : val;		\
+	}
+
+BUILD_SWAP(16)
+BUILD_SWAP(32)
+BUILD_SWAP(64)
+
+#define __FUNC(name, bits) name##bits
+#define _FUNC(name, bits) __FUNC(name, bits)
+#define FUNC(name) _FUNC(name, ELF_BITS)
+
+#define __ELF(x, bits) Elf##bits##_##x
+#define _ELF(x, bits) __ELF(x, bits)
+#define ELF(x) _ELF(x, ELF_BITS)
+
+/*
+ * Include genvdso.h twice with ELF_BITS defined differently to get functions
+ * for both ELF32 and ELF64.
+ */
+
+#define ELF_BITS 64
+#include "genvdso.h"
+#undef ELF_BITS
+
+#define ELF_BITS 32
+#include "genvdso.h"
+#undef ELF_BITS
+
+static void *map_vdso(const char *path, size_t *_size)
+{
+	int fd;
+	struct stat stat;
+	void *addr;
+	const Elf32_Ehdr *ehdr;
+
+	fd = open(path, O_RDWR);
+	if (fd < 0) {
+		fprintf(stderr, "%s: Failed to open '%s': %s\n", program_name,
+			path, strerror(errno));
+		return NULL;
+	}
+
+	if (fstat(fd, &stat) != 0) {
+		fprintf(stderr, "%s: Failed to stat '%s': %s\n", program_name,
+			path, strerror(errno));
+		close(fd);
+		return NULL;
+	}
+
+	addr = mmap(NULL, stat.st_size, PROT_READ | PROT_WRITE, MAP_SHARED, fd,
+		    0);
+	if (addr == MAP_FAILED) {
+		fprintf(stderr, "%s: Failed to map '%s': %s\n", program_name,
+			path, strerror(errno));
+		close(fd);
+		return NULL;
+	}
+
+	/* ELF32/64 header formats are the same for the bits we're checking. */
+	ehdr = addr;
+
+	if (memcmp(ehdr->e_ident, ELFMAG, SELFMAG) != 0) {
+		fprintf(stderr, "%s: '%s' is not an ELF file\n", program_name,
+			path);
+		close(fd);
+		return NULL;
+	}
+
+	elf_class = ehdr->e_ident[EI_CLASS];
+	switch (elf_class) {
+	case ELFCLASS32:
+	case ELFCLASS64:
+		break;
+	default:
+		fprintf(stderr, "%s: '%s' has invalid ELF class\n",
+			program_name, path);
+		close(fd);
+		return NULL;
+	}
+
+	switch (ehdr->e_ident[EI_DATA]) {
+	case ELFDATA2LSB:
+	case ELFDATA2MSB:
+		need_swap = ehdr->e_ident[EI_DATA] != HOST_ORDER;
+		break;
+	default:
+		fprintf(stderr, "%s: '%s' has invalid ELF data order\n",
+			program_name, path);
+		close(fd);
+		return NULL;
+	}
+
+	if (swap_uint16(ehdr->e_machine) != EM_MIPS) {
+		fprintf(stderr,
+			"%s: '%s' has invalid ELF machine (expected EM_MIPS)\n",
+			program_name, path);
+		close(fd);
+		return NULL;
+	} else if (swap_uint16(ehdr->e_type) != ET_DYN) {
+		fprintf(stderr,
+			"%s: '%s' has invalid ELF type (expected ET_DYN)\n",
+			program_name, path);
+		close(fd);
+		return NULL;
+	}
+
+	*_size = stat.st_size;
+	close(fd);
+	return addr;
+}
+
+static bool patch_vdso(const char *path, void *vdso)
+{
+	if (elf_class == ELFCLASS64)
+		return patch_vdso64(path, vdso);
+	else
+		return patch_vdso32(path, vdso);
+}
+
+static bool get_symbols(const char *path, void *vdso)
+{
+	if (elf_class == ELFCLASS64)
+		return get_symbols64(path, vdso);
+	else
+		return get_symbols32(path, vdso);
+}
+
+int main(int argc, char **argv)
+{
+	const char *dbg_vdso_path, *vdso_path, *out_path;
+	void *dbg_vdso, *vdso;
+	size_t dbg_vdso_size, vdso_size, i;
+
+	program_name = argv[0];
+
+	if (argc < 4 || argc > 5) {
+		fprintf(stderr,
+			"Usage: %s <debug VDSO> <stripped VDSO> <output file> [<name>]\n",
+			program_name);
+		return EXIT_FAILURE;
+	}
+
+	dbg_vdso_path = argv[1];
+	vdso_path = argv[2];
+	out_path = argv[3];
+	vdso_name = (argc > 4) ? argv[4] : "";
+
+	dbg_vdso = map_vdso(dbg_vdso_path, &dbg_vdso_size);
+	if (!dbg_vdso)
+		return EXIT_FAILURE;
+
+	vdso = map_vdso(vdso_path, &vdso_size);
+	if (!vdso)
+		return EXIT_FAILURE;
+
+	/* Patch both the VDSOs' ABI flags sections. */
+	if (!patch_vdso(dbg_vdso_path, dbg_vdso))
+		return EXIT_FAILURE;
+	if (!patch_vdso(vdso_path, vdso))
+		return EXIT_FAILURE;
+
+	if (msync(dbg_vdso, dbg_vdso_size, MS_SYNC) != 0) {
+		fprintf(stderr, "%s: Failed to sync '%s': %s\n", program_name,
+			dbg_vdso_path, strerror(errno));
+		return EXIT_FAILURE;
+	} else if (msync(vdso, vdso_size, MS_SYNC) != 0) {
+		fprintf(stderr, "%s: Failed to sync '%s': %s\n", program_name,
+			vdso_path, strerror(errno));
+		return EXIT_FAILURE;
+	}
+
+	out_file = fopen(out_path, "w");
+	if (!out_file) {
+		fprintf(stderr, "%s: Failed to open '%s': %s\n", program_name,
+			out_path, strerror(errno));
+		return EXIT_FAILURE;
+	}
+
+	fprintf(out_file, "/* Automatically generated - do not edit */\n");
+	fprintf(out_file, "#include <linux/linkage.h>\n");
+	fprintf(out_file, "#include <linux/mm.h>\n");
+	fprintf(out_file, "#include <asm/vdso.h>\n");
+	fprintf(out_file, "static int vdso_mremap(\n");
+	fprintf(out_file, "	const struct vm_special_mapping *sm,\n");
+	fprintf(out_file, "	struct vm_area_struct *new_vma)\n");
+	fprintf(out_file, "{\n");
+	fprintf(out_file, "	current->mm->context.vdso =\n");
+	fprintf(out_file, "	(void *)(new_vma->vm_start);\n");
+	fprintf(out_file, "	return 0;\n");
+	fprintf(out_file, "}\n");
+
+	/* Write out the stripped VDSO data. */
+	fprintf(out_file,
+		"static unsigned char vdso_data[PAGE_ALIGN(%zu)] __page_aligned_data = {\n\t",
+		vdso_size);
+	for (i = 0; i < vdso_size; i++) {
+		if (!(i % 10))
+			fprintf(out_file, "\n\t");
+		fprintf(out_file, "0x%02x, ", ((unsigned char *)vdso)[i]);
+	}
+	fprintf(out_file, "\n};\n");
+
+	/* Preallocate a page array. */
+	fprintf(out_file,
+		"static struct page *vdso_pages[PAGE_ALIGN(%zu) / PAGE_SIZE];\n",
+		vdso_size);
+
+	fprintf(out_file, "struct mips_vdso_image vdso_image%s%s = {\n",
+		(vdso_name[0]) ? "_" : "", vdso_name);
+	fprintf(out_file, "\t.data = vdso_data,\n");
+	fprintf(out_file, "\t.size = PAGE_ALIGN(%zu),\n", vdso_size);
+	fprintf(out_file, "\t.mapping = {\n");
+	fprintf(out_file, "\t\t.name = \"[vdso]\",\n");
+	fprintf(out_file, "\t\t.pages = vdso_pages,\n");
+	fprintf(out_file, "\t\t.mremap = vdso_mremap,\n");
+	fprintf(out_file, "\t},\n");
+
+	/* Calculate and write symbol offsets to <output file> */
+	if (!get_symbols(dbg_vdso_path, dbg_vdso)) {
+		unlink(out_path);
+		fclose(out_file);
+		return EXIT_FAILURE;
+	}
+
+	fprintf(out_file, "};\n");
+	fclose(out_file);
+
+	return EXIT_SUCCESS;
+}
diff --git a/arch/mips/vdso/genvdso.h b/arch/mips/vdso/genvdso.h
new file mode 100644
index 000000000..9bfb87403
--- /dev/null
+++ b/arch/mips/vdso/genvdso.h
@@ -0,0 +1,132 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2015 Imagination Technologies
+ * Author: Alex Smith <alex.smith@imgtec.com>
+ */
+
+static inline bool FUNC(patch_vdso)(const char *path, void *vdso)
+{
+	const ELF(Ehdr) *ehdr = vdso;
+	void *shdrs;
+	ELF(Shdr) *shdr;
+	char *shstrtab, *name;
+	uint16_t sh_count, sh_entsize, i;
+
+	shdrs = vdso + FUNC(swap_uint)(ehdr->e_shoff);
+	sh_count = swap_uint16(ehdr->e_shnum);
+	sh_entsize = swap_uint16(ehdr->e_shentsize);
+
+	shdr = shdrs + (sh_entsize * swap_uint16(ehdr->e_shstrndx));
+	shstrtab = vdso + FUNC(swap_uint)(shdr->sh_offset);
+
+	for (i = 0; i < sh_count; i++) {
+		shdr = shdrs + (i * sh_entsize);
+		name = shstrtab + swap_uint32(shdr->sh_name);
+
+		/*
+		 * Ensure there are no relocation sections - ld.so does not
+		 * relocate the VDSO so if there are relocations things will
+		 * break.
+		 */
+		switch (swap_uint32(shdr->sh_type)) {
+		case SHT_REL:
+		case SHT_RELA:
+			fprintf(stderr,
+				"%s: '%s' contains relocation sections\n",
+				program_name, path);
+			return false;
+		}
+
+		/* Check for existing sections. */
+		if (strcmp(name, ".MIPS.abiflags") == 0) {
+			fprintf(stderr,
+				"%s: '%s' already contains a '.MIPS.abiflags' section\n",
+				program_name, path);
+			return false;
+		}
+
+		if (strcmp(name, ".mips_abiflags") == 0) {
+			strcpy(name, ".MIPS.abiflags");
+			shdr->sh_type = swap_uint32(SHT_MIPS_ABIFLAGS);
+			shdr->sh_entsize = shdr->sh_size;
+		}
+	}
+
+	return true;
+}
+
+static inline bool FUNC(get_symbols)(const char *path, void *vdso)
+{
+	const ELF(Ehdr) *ehdr = vdso;
+	void *shdrs, *symtab;
+	ELF(Shdr) *shdr;
+	const ELF(Sym) *sym;
+	char *strtab, *name;
+	uint16_t sh_count, sh_entsize, st_count, st_entsize, i, j;
+	uint64_t offset;
+	uint32_t flags;
+
+	shdrs = vdso + FUNC(swap_uint)(ehdr->e_shoff);
+	sh_count = swap_uint16(ehdr->e_shnum);
+	sh_entsize = swap_uint16(ehdr->e_shentsize);
+
+	for (i = 0; i < sh_count; i++) {
+		shdr = shdrs + (i * sh_entsize);
+
+		if (swap_uint32(shdr->sh_type) == SHT_SYMTAB)
+			break;
+	}
+
+	if (i == sh_count) {
+		fprintf(stderr, "%s: '%s' has no symbol table\n", program_name,
+			path);
+		return false;
+	}
+
+	/* Get flags */
+	flags = swap_uint32(ehdr->e_flags);
+	if (elf_class == ELFCLASS64)
+		elf_abi = ABI_N64;
+	else if (flags & EF_MIPS_ABI2)
+		elf_abi = ABI_N32;
+	else
+		elf_abi = ABI_O32;
+
+	/* Get symbol table. */
+	symtab = vdso + FUNC(swap_uint)(shdr->sh_offset);
+	st_entsize = FUNC(swap_uint)(shdr->sh_entsize);
+	st_count = FUNC(swap_uint)(shdr->sh_size) / st_entsize;
+
+	/* Get string table. */
+	shdr = shdrs + (swap_uint32(shdr->sh_link) * sh_entsize);
+	strtab = vdso + FUNC(swap_uint)(shdr->sh_offset);
+
+	/* Write offsets for symbols needed by the kernel. */
+	for (i = 0; vdso_symbols[i].name; i++) {
+		if (!(vdso_symbols[i].abis & elf_abi))
+			continue;
+
+		for (j = 0; j < st_count; j++) {
+			sym = symtab + (j * st_entsize);
+			name = strtab + swap_uint32(sym->st_name);
+
+			if (!strcmp(name, vdso_symbols[i].name)) {
+				offset = FUNC(swap_uint)(sym->st_value);
+
+				fprintf(out_file,
+					"\t.%s = 0x%" PRIx64 ",\n",
+					vdso_symbols[i].offset_name, offset);
+				break;
+			}
+		}
+
+		if (j == st_count) {
+			fprintf(stderr,
+				"%s: '%s' is missing required symbol '%s'\n",
+				program_name, path, vdso_symbols[i].name);
+			return false;
+		}
+	}
+
+	return true;
+}
diff --git a/arch/mips/vdso/sigreturn.S b/arch/mips/vdso/sigreturn.S
new file mode 100644
index 000000000..e5c0ab98a
--- /dev/null
+++ b/arch/mips/vdso/sigreturn.S
@@ -0,0 +1,35 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2015 Imagination Technologies
+ * Author: Alex Smith <alex.smith@imgtec.com>
+ */
+
+#include <asm/vdso/vdso.h>
+
+#include <uapi/asm/unistd.h>
+
+#include <asm/regdef.h>
+#include <asm/asm.h>
+
+	.section	.text
+	.cfi_sections	.debug_frame
+
+LEAF(__vdso_rt_sigreturn)
+	.cfi_signal_frame
+
+	li	v0, __NR_rt_sigreturn
+	syscall
+
+	END(__vdso_rt_sigreturn)
+
+#if _MIPS_SIM == _MIPS_SIM_ABI32
+
+LEAF(__vdso_sigreturn)
+	.cfi_signal_frame
+
+	li	v0, __NR_sigreturn
+	syscall
+
+	END(__vdso_sigreturn)
+
+#endif
diff --git a/arch/mips/vdso/vdso.lds.S b/arch/mips/vdso/vdso.lds.S
new file mode 100644
index 000000000..d90b65724
--- /dev/null
+++ b/arch/mips/vdso/vdso.lds.S
@@ -0,0 +1,105 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2015 Imagination Technologies
+ * Author: Alex Smith <alex.smith@imgtec.com>
+ */
+
+#include <asm/sgidefs.h>
+
+#if _MIPS_SIM == _MIPS_SIM_ABI64
+OUTPUT_FORMAT("elf64-tradlittlemips", "elf64-tradbigmips", "elf64-tradlittlemips")
+#elif _MIPS_SIM == _MIPS_SIM_NABI32
+OUTPUT_FORMAT("elf32-ntradlittlemips", "elf32-ntradbigmips", "elf32-ntradlittlemips")
+#else
+OUTPUT_FORMAT("elf32-tradlittlemips", "elf32-tradbigmips", "elf32-tradlittlemips")
+#endif
+
+OUTPUT_ARCH(mips)
+
+SECTIONS
+{
+	PROVIDE(_start = .);
+	. = SIZEOF_HEADERS;
+
+	/*
+	 * In order to retain compatibility with older toolchains we provide the
+	 * ABI flags section ourself. Newer assemblers will automatically
+	 * generate .MIPS.abiflags sections so we discard such input sections,
+	 * and then manually define our own section here. genvdso will patch
+	 * this section to have the correct name/type.
+	 */
+	.mips_abiflags	: { *(.mips_abiflags) } 	:text :abiflags
+
+	.reginfo	: { *(.reginfo) }		:text :reginfo
+
+	.hash		: { *(.hash) }			:text
+	.gnu.hash	: { *(.gnu.hash) }
+	.dynsym		: { *(.dynsym) }
+	.dynstr		: { *(.dynstr) }
+	.gnu.version	: { *(.gnu.version) }
+	.gnu.version_d	: { *(.gnu.version_d) }
+	.gnu.version_r	: { *(.gnu.version_r) }
+
+	.note		: { *(.note.*) }		:text :note
+
+	.text		: { *(.text*) }			:text
+	PROVIDE (__etext = .);
+	PROVIDE (_etext = .);
+	PROVIDE (etext = .);
+
+	.eh_frame_hdr	: { *(.eh_frame_hdr) }		:text :eh_frame_hdr
+	.eh_frame	: { KEEP (*(.eh_frame)) }	:text
+
+	.dynamic	: { *(.dynamic) }		:text :dynamic
+
+	.rodata		: { *(.rodata*) }		:text
+
+	_end = .;
+	PROVIDE(end = .);
+
+	/DISCARD/	: {
+		*(.MIPS.abiflags)
+		*(.gnu.attributes)
+		*(.note.GNU-stack)
+		*(.data .data.* .gnu.linkonce.d.* .sdata*)
+		*(.bss .sbss .dynbss .dynsbss)
+	}
+}
+
+PHDRS
+{
+	/*
+	 * Provide a PT_MIPS_ABIFLAGS header to assign the ABI flags section
+	 * to. We can specify the header type directly here so no modification
+	 * is needed later on.
+	 */
+	abiflags	0x70000003;
+
+	/*
+	 * The ABI flags header must exist directly after the PT_INTERP header,
+	 * so we must explicitly place the PT_MIPS_REGINFO header after it to
+	 * stop the linker putting one in at the start.
+	 */
+	reginfo		0x70000000;
+
+	text		PT_LOAD		FLAGS(5) FILEHDR PHDRS; /* PF_R|PF_X */
+	dynamic		PT_DYNAMIC	FLAGS(4);		/* PF_R */
+	note		PT_NOTE		FLAGS(4);		/* PF_R */
+	eh_frame_hdr	PT_GNU_EH_FRAME;
+}
+
+VERSION
+{
+	LINUX_2.6 {
+#ifndef CONFIG_MIPS_DISABLE_VDSO
+	global:
+		__vdso_clock_gettime;
+		__vdso_gettimeofday;
+		__vdso_clock_getres;
+#if _MIPS_SIM != _MIPS_SIM_ABI64
+		__vdso_clock_gettime64;
+#endif
+#endif
+	local: *;
+	};
+}
diff --git a/arch/mips/vdso/vgettimeofday.c b/arch/mips/vdso/vgettimeofday.c
new file mode 100644
index 000000000..6b83b6376
--- /dev/null
+++ b/arch/mips/vdso/vgettimeofday.c
@@ -0,0 +1,78 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * MIPS64 and compat userspace implementations of gettimeofday()
+ * and similar.
+ *
+ * Copyright (C) 2015 Imagination Technologies
+ * Copyright (C) 2018 ARM Limited
+ *
+ */
+#include <linux/time.h>
+#include <linux/types.h>
+
+#if _MIPS_SIM != _MIPS_SIM_ABI64
+int __vdso_clock_gettime(clockid_t clock,
+			 struct old_timespec32 *ts)
+{
+	return __cvdso_clock_gettime32(clock, ts);
+}
+
+#ifdef CONFIG_MIPS_CLOCK_VSYSCALL
+
+/*
+ * This is behind the ifdef so that we don't provide the symbol when there's no
+ * possibility of there being a usable clocksource, because there's nothing we
+ * can do without it. When libc fails the symbol lookup it should fall back on
+ * the standard syscall path.
+ */
+int __vdso_gettimeofday(struct __kernel_old_timeval *tv,
+			struct timezone *tz)
+{
+	return __cvdso_gettimeofday(tv, tz);
+}
+
+#endif /* CONFIG_MIPS_CLOCK_VSYSCALL */
+
+int __vdso_clock_getres(clockid_t clock_id,
+			struct old_timespec32 *res)
+{
+	return __cvdso_clock_getres_time32(clock_id, res);
+}
+
+int __vdso_clock_gettime64(clockid_t clock,
+			   struct __kernel_timespec *ts)
+{
+	return __cvdso_clock_gettime(clock, ts);
+}
+
+#else
+
+int __vdso_clock_gettime(clockid_t clock,
+			 struct __kernel_timespec *ts)
+{
+	return __cvdso_clock_gettime(clock, ts);
+}
+
+#ifdef CONFIG_MIPS_CLOCK_VSYSCALL
+
+/*
+ * This is behind the ifdef so that we don't provide the symbol when there's no
+ * possibility of there being a usable clocksource, because there's nothing we
+ * can do without it. When libc fails the symbol lookup it should fall back on
+ * the standard syscall path.
+ */
+int __vdso_gettimeofday(struct __kernel_old_timeval *tv,
+			struct timezone *tz)
+{
+	return __cvdso_gettimeofday(tv, tz);
+}
+
+#endif /* CONFIG_MIPS_CLOCK_VSYSCALL */
+
+int __vdso_clock_getres(clockid_t clock_id,
+			struct __kernel_timespec *res)
+{
+	return __cvdso_clock_getres(clock_id, res);
+}
+
+#endif