diff options
Diffstat (limited to 'drivers/block/mtip32xx/mtip32xx.h')
| -rw-r--r-- | drivers/block/mtip32xx/mtip32xx.h | 467 |
1 files changed, 467 insertions, 0 deletions
diff --git a/drivers/block/mtip32xx/mtip32xx.h b/drivers/block/mtip32xx/mtip32xx.h new file mode 100644 index 000000000..f7328f19a --- /dev/null +++ b/drivers/block/mtip32xx/mtip32xx.h @@ -0,0 +1,467 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ +/* + * mtip32xx.h - Header file for the P320 SSD Block Driver + * Copyright (C) 2011 Micron Technology, Inc. + * + * Portions of this code were derived from works subjected to the + * following copyright: + * Copyright (C) 2009 Integrated Device Technology, Inc. + */ + +#ifndef __MTIP32XX_H__ +#define __MTIP32XX_H__ + +#include <linux/spinlock.h> +#include <linux/rwsem.h> +#include <linux/ata.h> +#include <linux/interrupt.h> + +/* Offset of Subsystem Device ID in pci confoguration space */ +#define PCI_SUBSYSTEM_DEVICEID 0x2E + +/* offset of Device Control register in PCIe extended capabilites space */ +#define PCIE_CONFIG_EXT_DEVICE_CONTROL_OFFSET 0x48 + +/* check for erase mode support during secure erase */ +#define MTIP_SEC_ERASE_MODE 0x2 + +/* # of times to retry timed out/failed IOs */ +#define MTIP_MAX_RETRIES 2 + +/* Various timeout values in ms */ +#define MTIP_NCQ_CMD_TIMEOUT_MS 15000 +#define MTIP_IOCTL_CMD_TIMEOUT_MS 5000 +#define MTIP_INT_CMD_TIMEOUT_MS 5000 +#define MTIP_QUIESCE_IO_TIMEOUT_MS (MTIP_NCQ_CMD_TIMEOUT_MS * \ + (MTIP_MAX_RETRIES + 1)) + +/* check for timeouts every 500ms */ +#define MTIP_TIMEOUT_CHECK_PERIOD 500 + +/* ftl rebuild */ +#define MTIP_FTL_REBUILD_OFFSET 142 +#define MTIP_FTL_REBUILD_MAGIC 0xED51 +#define MTIP_FTL_REBUILD_TIMEOUT_MS 2400000 + +/* unaligned IO handling */ +#define MTIP_MAX_UNALIGNED_SLOTS 2 + +/* Macro to extract the tag bit number from a tag value. */ +#define MTIP_TAG_BIT(tag) (tag & 0x1F) + +/* + * Macro to extract the tag index from a tag value. The index + * is used to access the correct s_active/Command Issue register based + * on the tag value. + */ +#define MTIP_TAG_INDEX(tag) (tag >> 5) + +/* + * Maximum number of scatter gather entries + * a single command may have. + */ +#define MTIP_MAX_SG 504 + +/* + * Maximum number of slot groups (Command Issue & s_active registers) + * NOTE: This is the driver maximum; check dd->slot_groups for actual value. + */ +#define MTIP_MAX_SLOT_GROUPS 8 + +/* Internal command tag. */ +#define MTIP_TAG_INTERNAL 0 + +/* Micron Vendor ID & P320x SSD Device ID */ +#define PCI_VENDOR_ID_MICRON 0x1344 +#define P320H_DEVICE_ID 0x5150 +#define P320M_DEVICE_ID 0x5151 +#define P320S_DEVICE_ID 0x5152 +#define P325M_DEVICE_ID 0x5153 +#define P420H_DEVICE_ID 0x5160 +#define P420M_DEVICE_ID 0x5161 +#define P425M_DEVICE_ID 0x5163 + +/* Driver name and version strings */ +#define MTIP_DRV_NAME "mtip32xx" +#define MTIP_DRV_VERSION "1.3.1" + +/* Maximum number of minor device numbers per device. */ +#define MTIP_MAX_MINORS 16 + +/* Maximum number of supported command slots. */ +#define MTIP_MAX_COMMAND_SLOTS (MTIP_MAX_SLOT_GROUPS * 32) + +/* + * Per-tag bitfield size in longs. + * Linux bit manipulation functions + * (i.e. test_and_set_bit, find_next_zero_bit) + * manipulate memory in longs, so we try to make the math work. + * take the slot groups and find the number of longs, rounding up. + * Careful! i386 and x86_64 use different size longs! + */ +#define U32_PER_LONG (sizeof(long) / sizeof(u32)) +#define SLOTBITS_IN_LONGS ((MTIP_MAX_SLOT_GROUPS + \ + (U32_PER_LONG-1))/U32_PER_LONG) + +/* BAR number used to access the HBA registers. */ +#define MTIP_ABAR 5 + +#ifdef DEBUG + #define dbg_printk(format, arg...) \ + printk(pr_fmt(format), ##arg); +#else + #define dbg_printk(format, arg...) +#endif + +#define MTIP_DFS_MAX_BUF_SIZE 1024 + +enum { + /* below are bit numbers in 'flags' defined in mtip_port */ + MTIP_PF_IC_ACTIVE_BIT = 0, /* pio/ioctl */ + MTIP_PF_EH_ACTIVE_BIT = 1, /* error handling */ + MTIP_PF_SE_ACTIVE_BIT = 2, /* secure erase */ + MTIP_PF_DM_ACTIVE_BIT = 3, /* download microcde */ + MTIP_PF_TO_ACTIVE_BIT = 9, /* timeout handling */ + MTIP_PF_PAUSE_IO = ((1 << MTIP_PF_IC_ACTIVE_BIT) | + (1 << MTIP_PF_EH_ACTIVE_BIT) | + (1 << MTIP_PF_SE_ACTIVE_BIT) | + (1 << MTIP_PF_DM_ACTIVE_BIT) | + (1 << MTIP_PF_TO_ACTIVE_BIT)), + MTIP_PF_HOST_CAP_64 = 10, /* cache HOST_CAP_64 */ + + MTIP_PF_SVC_THD_ACTIVE_BIT = 4, + MTIP_PF_ISSUE_CMDS_BIT = 5, + MTIP_PF_REBUILD_BIT = 6, + MTIP_PF_SVC_THD_STOP_BIT = 8, + + MTIP_PF_SVC_THD_WORK = ((1 << MTIP_PF_EH_ACTIVE_BIT) | + (1 << MTIP_PF_ISSUE_CMDS_BIT) | + (1 << MTIP_PF_REBUILD_BIT) | + (1 << MTIP_PF_SVC_THD_STOP_BIT) | + (1 << MTIP_PF_TO_ACTIVE_BIT)), + + /* below are bit numbers in 'dd_flag' defined in driver_data */ + MTIP_DDF_SEC_LOCK_BIT = 0, + MTIP_DDF_REMOVE_PENDING_BIT = 1, + MTIP_DDF_OVER_TEMP_BIT = 2, + MTIP_DDF_WRITE_PROTECT_BIT = 3, + MTIP_DDF_CLEANUP_BIT = 5, + MTIP_DDF_RESUME_BIT = 6, + MTIP_DDF_INIT_DONE_BIT = 7, + MTIP_DDF_REBUILD_FAILED_BIT = 8, + + MTIP_DDF_STOP_IO = ((1 << MTIP_DDF_REMOVE_PENDING_BIT) | + (1 << MTIP_DDF_SEC_LOCK_BIT) | + (1 << MTIP_DDF_OVER_TEMP_BIT) | + (1 << MTIP_DDF_WRITE_PROTECT_BIT) | + (1 << MTIP_DDF_REBUILD_FAILED_BIT)), + +}; + +struct smart_attr { + u8 attr_id; + __le16 flags; + u8 cur; + u8 worst; + __le32 data; + u8 res[3]; +} __packed; + +struct mtip_work { + struct work_struct work; + void *port; + int cpu_binding; + u32 completed; +} ____cacheline_aligned_in_smp; + +#define DEFINE_HANDLER(group) \ + void mtip_workq_sdbf##group(struct work_struct *work) \ + { \ + struct mtip_work *w = (struct mtip_work *) work; \ + mtip_workq_sdbfx(w->port, group, w->completed); \ + } + +/* Register Frame Information Structure (FIS), host to device. */ +struct host_to_dev_fis { + /* + * FIS type. + * - 27h Register FIS, host to device. + * - 34h Register FIS, device to host. + * - 39h DMA Activate FIS, device to host. + * - 41h DMA Setup FIS, bi-directional. + * - 46h Data FIS, bi-directional. + * - 58h BIST Activate FIS, bi-directional. + * - 5Fh PIO Setup FIS, device to host. + * - A1h Set Device Bits FIS, device to host. + */ + unsigned char type; + unsigned char opts; + unsigned char command; + unsigned char features; + + union { + unsigned char lba_low; + unsigned char sector; + }; + union { + unsigned char lba_mid; + unsigned char cyl_low; + }; + union { + unsigned char lba_hi; + unsigned char cyl_hi; + }; + union { + unsigned char device; + unsigned char head; + }; + + union { + unsigned char lba_low_ex; + unsigned char sector_ex; + }; + union { + unsigned char lba_mid_ex; + unsigned char cyl_low_ex; + }; + union { + unsigned char lba_hi_ex; + unsigned char cyl_hi_ex; + }; + unsigned char features_ex; + + unsigned char sect_count; + unsigned char sect_cnt_ex; + unsigned char res2; + unsigned char control; + + unsigned int res3; +}; + +/* Command header structure. */ +struct mtip_cmd_hdr { + /* + * Command options. + * - Bits 31:16 Number of PRD entries. + * - Bits 15:8 Unused in this implementation. + * - Bit 7 Prefetch bit, informs the drive to prefetch PRD entries. + * - Bit 6 Write bit, should be set when writing data to the device. + * - Bit 5 Unused in this implementation. + * - Bits 4:0 Length of the command FIS in DWords (DWord = 4 bytes). + */ + __le32 opts; + /* This field is unsed when using NCQ. */ + union { + __le32 byte_count; + __le32 status; + }; + /* + * Lower 32 bits of the command table address associated with this + * header. The command table addresses must be 128 byte aligned. + */ + __le32 ctba; + /* + * If 64 bit addressing is used this field is the upper 32 bits + * of the command table address associated with this command. + */ + __le32 ctbau; + /* Reserved and unused. */ + u32 res[4]; +}; + +/* Command scatter gather structure (PRD). */ +struct mtip_cmd_sg { + /* + * Low 32 bits of the data buffer address. For P320 this + * address must be 8 byte aligned signified by bits 2:0 being + * set to 0. + */ + __le32 dba; + /* + * When 64 bit addressing is used this field is the upper + * 32 bits of the data buffer address. + */ + __le32 dba_upper; + /* Unused. */ + __le32 reserved; + /* + * Bit 31: interrupt when this data block has been transferred. + * Bits 30..22: reserved + * Bits 21..0: byte count (minus 1). For P320 the byte count must be + * 8 byte aligned signified by bits 2:0 being set to 1. + */ + __le32 info; +}; +struct mtip_port; + +struct mtip_int_cmd; + +/* Structure used to describe a command. */ +struct mtip_cmd { + void *command; /* ptr to command table entry */ + + dma_addr_t command_dma; /* corresponding physical address */ + + int scatter_ents; /* Number of scatter list entries used */ + + int unaligned; /* command is unaligned on 4k boundary */ + + union { + struct scatterlist sg[MTIP_MAX_SG]; /* Scatter list entries */ + struct mtip_int_cmd *icmd; + }; + + int retries; /* The number of retries left for this command. */ + + int direction; /* Data transfer direction */ + blk_status_t status; +}; + +/* Structure used to describe a port. */ +struct mtip_port { + /* Pointer back to the driver data for this port. */ + struct driver_data *dd; + /* + * Used to determine if the data pointed to by the + * identify field is valid. + */ + unsigned long identify_valid; + /* Base address of the memory mapped IO for the port. */ + void __iomem *mmio; + /* Array of pointers to the memory mapped s_active registers. */ + void __iomem *s_active[MTIP_MAX_SLOT_GROUPS]; + /* Array of pointers to the memory mapped completed registers. */ + void __iomem *completed[MTIP_MAX_SLOT_GROUPS]; + /* Array of pointers to the memory mapped Command Issue registers. */ + void __iomem *cmd_issue[MTIP_MAX_SLOT_GROUPS]; + /* + * Pointer to the beginning of the command header memory as used + * by the driver. + */ + void *command_list; + /* + * Pointer to the beginning of the command header memory as used + * by the DMA. + */ + dma_addr_t command_list_dma; + /* + * Pointer to the beginning of the RX FIS memory as used + * by the driver. + */ + void *rxfis; + /* + * Pointer to the beginning of the RX FIS memory as used + * by the DMA. + */ + dma_addr_t rxfis_dma; + /* + * Pointer to the DMA region for RX Fis, Identify, RLE10, and SMART + */ + void *block1; + /* + * DMA address of region for RX Fis, Identify, RLE10, and SMART + */ + dma_addr_t block1_dma; + /* + * Pointer to the beginning of the identify data memory as used + * by the driver. + */ + u16 *identify; + /* + * Pointer to the beginning of the identify data memory as used + * by the DMA. + */ + dma_addr_t identify_dma; + /* + * Pointer to the beginning of a sector buffer that is used + * by the driver when issuing internal commands. + */ + u16 *sector_buffer; + /* + * Pointer to the beginning of a sector buffer that is used + * by the DMA when the driver issues internal commands. + */ + dma_addr_t sector_buffer_dma; + + u16 *log_buf; + dma_addr_t log_buf_dma; + + u8 *smart_buf; + dma_addr_t smart_buf_dma; + + /* + * used to queue commands when an internal command is in progress + * or error handling is active + */ + unsigned long cmds_to_issue[SLOTBITS_IN_LONGS]; + /* Used by mtip_service_thread to wait for an event */ + wait_queue_head_t svc_wait; + /* + * indicates the state of the port. Also, helps the service thread + * to determine its action on wake up. + */ + unsigned long flags; + /* + * Timer used to complete commands that have been active for too long. + */ + unsigned long ic_pause_timer; + + /* Counter to control queue depth of unaligned IOs */ + atomic_t cmd_slot_unal; + + /* Spinlock for working around command-issue bug. */ + spinlock_t cmd_issue_lock[MTIP_MAX_SLOT_GROUPS]; +}; + +/* + * Driver private data structure. + * + * One structure is allocated per probed device. + */ +struct driver_data { + void __iomem *mmio; /* Base address of the HBA registers. */ + + int major; /* Major device number. */ + + int instance; /* Instance number. First device probed is 0, ... */ + + struct gendisk *disk; /* Pointer to our gendisk structure. */ + + struct pci_dev *pdev; /* Pointer to the PCI device structure. */ + + struct request_queue *queue; /* Our request queue. */ + + struct blk_mq_tag_set tags; /* blk_mq tags */ + + struct mtip_port *port; /* Pointer to the port data structure. */ + + unsigned product_type; /* magic value declaring the product type */ + + unsigned slot_groups; /* number of slot groups the product supports */ + + unsigned long index; /* Index to determine the disk name */ + + unsigned long dd_flag; /* NOTE: use atomic bit operations on this */ + + struct task_struct *mtip_svc_handler; /* task_struct of svc thd */ + + struct dentry *dfs_node; + + bool sr; + + int numa_node; /* NUMA support */ + + char workq_name[32]; + + struct workqueue_struct *isr_workq; + + atomic_t irq_workers_active; + + struct mtip_work work[MTIP_MAX_SLOT_GROUPS]; + + int isr_binding; + + int unal_qdepth; /* qdepth of unaligned IO queue */ +}; + +#endif |