diff options
Diffstat (limited to '')
| -rw-r--r-- | drivers/gpu/drm/i2c/tda998x_drv.c | 2113 |
1 files changed, 2113 insertions, 0 deletions
diff --git a/drivers/gpu/drm/i2c/tda998x_drv.c b/drivers/gpu/drm/i2c/tda998x_drv.c new file mode 100644 index 000000000..d444e7fff --- /dev/null +++ b/drivers/gpu/drm/i2c/tda998x_drv.c @@ -0,0 +1,2113 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (C) 2012 Texas Instruments + * Author: Rob Clark <robdclark@gmail.com> + */ + +#include <linux/component.h> +#include <linux/gpio/consumer.h> +#include <linux/hdmi.h> +#include <linux/i2c.h> +#include <linux/module.h> +#include <linux/platform_data/tda9950.h> +#include <linux/irq.h> +#include <sound/asoundef.h> +#include <sound/hdmi-codec.h> + +#include <drm/drm_atomic_helper.h> +#include <drm/drm_bridge.h> +#include <drm/drm_edid.h> +#include <drm/drm_of.h> +#include <drm/drm_print.h> +#include <drm/drm_probe_helper.h> +#include <drm/drm_simple_kms_helper.h> +#include <drm/i2c/tda998x.h> + +#include <media/cec-notifier.h> + +#define DBG(fmt, ...) DRM_DEBUG(fmt"\n", ##__VA_ARGS__) + +enum { + AUDIO_ROUTE_I2S, + AUDIO_ROUTE_SPDIF, + AUDIO_ROUTE_NUM +}; + +struct tda998x_audio_route { + u8 ena_aclk; + u8 mux_ap; + u8 aip_clksel; +}; + +struct tda998x_audio_settings { + const struct tda998x_audio_route *route; + struct hdmi_audio_infoframe cea; + unsigned int sample_rate; + u8 status[5]; + u8 ena_ap; + u8 i2s_format; + u8 cts_n; +}; + +struct tda998x_priv { + struct i2c_client *cec; + struct i2c_client *hdmi; + struct mutex mutex; + u16 rev; + u8 cec_addr; + u8 current_page; + bool is_on; + bool supports_infoframes; + bool sink_has_audio; + enum hdmi_quantization_range rgb_quant_range; + u8 vip_cntrl_0; + u8 vip_cntrl_1; + u8 vip_cntrl_2; + unsigned long tmds_clock; + struct tda998x_audio_settings audio; + + struct platform_device *audio_pdev; + struct mutex audio_mutex; + + struct mutex edid_mutex; + wait_queue_head_t wq_edid; + volatile int wq_edid_wait; + + struct work_struct detect_work; + struct timer_list edid_delay_timer; + wait_queue_head_t edid_delay_waitq; + bool edid_delay_active; + + struct drm_encoder encoder; + struct drm_bridge bridge; + struct drm_connector connector; + + u8 audio_port_enable[AUDIO_ROUTE_NUM]; + struct tda9950_glue cec_glue; + struct gpio_desc *calib; + struct cec_notifier *cec_notify; +}; + +#define conn_to_tda998x_priv(x) \ + container_of(x, struct tda998x_priv, connector) +#define enc_to_tda998x_priv(x) \ + container_of(x, struct tda998x_priv, encoder) +#define bridge_to_tda998x_priv(x) \ + container_of(x, struct tda998x_priv, bridge) + +/* The TDA9988 series of devices use a paged register scheme.. to simplify + * things we encode the page # in upper bits of the register #. To read/ + * write a given register, we need to make sure CURPAGE register is set + * appropriately. Which implies reads/writes are not atomic. Fun! + */ + +#define REG(page, addr) (((page) << 8) | (addr)) +#define REG2ADDR(reg) ((reg) & 0xff) +#define REG2PAGE(reg) (((reg) >> 8) & 0xff) + +#define REG_CURPAGE 0xff /* write */ + + +/* Page 00h: General Control */ +#define REG_VERSION_LSB REG(0x00, 0x00) /* read */ +#define REG_MAIN_CNTRL0 REG(0x00, 0x01) /* read/write */ +# define MAIN_CNTRL0_SR (1 << 0) +# define MAIN_CNTRL0_DECS (1 << 1) +# define MAIN_CNTRL0_DEHS (1 << 2) +# define MAIN_CNTRL0_CECS (1 << 3) +# define MAIN_CNTRL0_CEHS (1 << 4) +# define MAIN_CNTRL0_SCALER (1 << 7) +#define REG_VERSION_MSB REG(0x00, 0x02) /* read */ +#define REG_SOFTRESET REG(0x00, 0x0a) /* write */ +# define SOFTRESET_AUDIO (1 << 0) +# define SOFTRESET_I2C_MASTER (1 << 1) +#define REG_DDC_DISABLE REG(0x00, 0x0b) /* read/write */ +#define REG_CCLK_ON REG(0x00, 0x0c) /* read/write */ +#define REG_I2C_MASTER REG(0x00, 0x0d) /* read/write */ +# define I2C_MASTER_DIS_MM (1 << 0) +# define I2C_MASTER_DIS_FILT (1 << 1) +# define I2C_MASTER_APP_STRT_LAT (1 << 2) +#define REG_FEAT_POWERDOWN REG(0x00, 0x0e) /* read/write */ +# define FEAT_POWERDOWN_PREFILT BIT(0) +# define FEAT_POWERDOWN_CSC BIT(1) +# define FEAT_POWERDOWN_SPDIF (1 << 3) +#define REG_INT_FLAGS_0 REG(0x00, 0x0f) /* read/write */ +#define REG_INT_FLAGS_1 REG(0x00, 0x10) /* read/write */ +#define REG_INT_FLAGS_2 REG(0x00, 0x11) /* read/write */ +# define INT_FLAGS_2_EDID_BLK_RD (1 << 1) +#define REG_ENA_ACLK REG(0x00, 0x16) /* read/write */ +#define REG_ENA_VP_0 REG(0x00, 0x18) /* read/write */ +#define REG_ENA_VP_1 REG(0x00, 0x19) /* read/write */ +#define REG_ENA_VP_2 REG(0x00, 0x1a) /* read/write */ +#define REG_ENA_AP REG(0x00, 0x1e) /* read/write */ +#define REG_VIP_CNTRL_0 REG(0x00, 0x20) /* write */ +# define VIP_CNTRL_0_MIRR_A (1 << 7) +# define VIP_CNTRL_0_SWAP_A(x) (((x) & 7) << 4) +# define VIP_CNTRL_0_MIRR_B (1 << 3) +# define VIP_CNTRL_0_SWAP_B(x) (((x) & 7) << 0) +#define REG_VIP_CNTRL_1 REG(0x00, 0x21) /* write */ +# define VIP_CNTRL_1_MIRR_C (1 << 7) +# define VIP_CNTRL_1_SWAP_C(x) (((x) & 7) << 4) +# define VIP_CNTRL_1_MIRR_D (1 << 3) +# define VIP_CNTRL_1_SWAP_D(x) (((x) & 7) << 0) +#define REG_VIP_CNTRL_2 REG(0x00, 0x22) /* write */ +# define VIP_CNTRL_2_MIRR_E (1 << 7) +# define VIP_CNTRL_2_SWAP_E(x) (((x) & 7) << 4) +# define VIP_CNTRL_2_MIRR_F (1 << 3) +# define VIP_CNTRL_2_SWAP_F(x) (((x) & 7) << 0) +#define REG_VIP_CNTRL_3 REG(0x00, 0x23) /* write */ +# define VIP_CNTRL_3_X_TGL (1 << 0) +# define VIP_CNTRL_3_H_TGL (1 << 1) +# define VIP_CNTRL_3_V_TGL (1 << 2) +# define VIP_CNTRL_3_EMB (1 << 3) +# define VIP_CNTRL_3_SYNC_DE (1 << 4) +# define VIP_CNTRL_3_SYNC_HS (1 << 5) +# define VIP_CNTRL_3_DE_INT (1 << 6) +# define VIP_CNTRL_3_EDGE (1 << 7) +#define REG_VIP_CNTRL_4 REG(0x00, 0x24) /* write */ +# define VIP_CNTRL_4_BLC(x) (((x) & 3) << 0) +# define VIP_CNTRL_4_BLANKIT(x) (((x) & 3) << 2) +# define VIP_CNTRL_4_CCIR656 (1 << 4) +# define VIP_CNTRL_4_656_ALT (1 << 5) +# define VIP_CNTRL_4_TST_656 (1 << 6) +# define VIP_CNTRL_4_TST_PAT (1 << 7) +#define REG_VIP_CNTRL_5 REG(0x00, 0x25) /* write */ +# define VIP_CNTRL_5_CKCASE (1 << 0) +# define VIP_CNTRL_5_SP_CNT(x) (((x) & 3) << 1) +#define REG_MUX_AP REG(0x00, 0x26) /* read/write */ +# define MUX_AP_SELECT_I2S 0x64 +# define MUX_AP_SELECT_SPDIF 0x40 +#define REG_MUX_VP_VIP_OUT REG(0x00, 0x27) /* read/write */ +#define REG_MAT_CONTRL REG(0x00, 0x80) /* write */ +# define MAT_CONTRL_MAT_SC(x) (((x) & 3) << 0) +# define MAT_CONTRL_MAT_BP (1 << 2) +#define REG_VIDFORMAT REG(0x00, 0xa0) /* write */ +#define REG_REFPIX_MSB REG(0x00, 0xa1) /* write */ +#define REG_REFPIX_LSB REG(0x00, 0xa2) /* write */ +#define REG_REFLINE_MSB REG(0x00, 0xa3) /* write */ +#define REG_REFLINE_LSB REG(0x00, 0xa4) /* write */ +#define REG_NPIX_MSB REG(0x00, 0xa5) /* write */ +#define REG_NPIX_LSB REG(0x00, 0xa6) /* write */ +#define REG_NLINE_MSB REG(0x00, 0xa7) /* write */ +#define REG_NLINE_LSB REG(0x00, 0xa8) /* write */ +#define REG_VS_LINE_STRT_1_MSB REG(0x00, 0xa9) /* write */ +#define REG_VS_LINE_STRT_1_LSB REG(0x00, 0xaa) /* write */ +#define REG_VS_PIX_STRT_1_MSB REG(0x00, 0xab) /* write */ +#define REG_VS_PIX_STRT_1_LSB REG(0x00, 0xac) /* write */ +#define REG_VS_LINE_END_1_MSB REG(0x00, 0xad) /* write */ +#define REG_VS_LINE_END_1_LSB REG(0x00, 0xae) /* write */ +#define REG_VS_PIX_END_1_MSB REG(0x00, 0xaf) /* write */ +#define REG_VS_PIX_END_1_LSB REG(0x00, 0xb0) /* write */ +#define REG_VS_LINE_STRT_2_MSB REG(0x00, 0xb1) /* write */ +#define REG_VS_LINE_STRT_2_LSB REG(0x00, 0xb2) /* write */ +#define REG_VS_PIX_STRT_2_MSB REG(0x00, 0xb3) /* write */ +#define REG_VS_PIX_STRT_2_LSB REG(0x00, 0xb4) /* write */ +#define REG_VS_LINE_END_2_MSB REG(0x00, 0xb5) /* write */ +#define REG_VS_LINE_END_2_LSB REG(0x00, 0xb6) /* write */ +#define REG_VS_PIX_END_2_MSB REG(0x00, 0xb7) /* write */ +#define REG_VS_PIX_END_2_LSB REG(0x00, 0xb8) /* write */ +#define REG_HS_PIX_START_MSB REG(0x00, 0xb9) /* write */ +#define REG_HS_PIX_START_LSB REG(0x00, 0xba) /* write */ +#define REG_HS_PIX_STOP_MSB REG(0x00, 0xbb) /* write */ +#define REG_HS_PIX_STOP_LSB REG(0x00, 0xbc) /* write */ +#define REG_VWIN_START_1_MSB REG(0x00, 0xbd) /* write */ +#define REG_VWIN_START_1_LSB REG(0x00, 0xbe) /* write */ +#define REG_VWIN_END_1_MSB REG(0x00, 0xbf) /* write */ +#define REG_VWIN_END_1_LSB REG(0x00, 0xc0) /* write */ +#define REG_VWIN_START_2_MSB REG(0x00, 0xc1) /* write */ +#define REG_VWIN_START_2_LSB REG(0x00, 0xc2) /* write */ +#define REG_VWIN_END_2_MSB REG(0x00, 0xc3) /* write */ +#define REG_VWIN_END_2_LSB REG(0x00, 0xc4) /* write */ +#define REG_DE_START_MSB REG(0x00, 0xc5) /* write */ +#define REG_DE_START_LSB REG(0x00, 0xc6) /* write */ +#define REG_DE_STOP_MSB REG(0x00, 0xc7) /* write */ +#define REG_DE_STOP_LSB REG(0x00, 0xc8) /* write */ +#define REG_TBG_CNTRL_0 REG(0x00, 0xca) /* write */ +# define TBG_CNTRL_0_TOP_TGL (1 << 0) +# define TBG_CNTRL_0_TOP_SEL (1 << 1) +# define TBG_CNTRL_0_DE_EXT (1 << 2) +# define TBG_CNTRL_0_TOP_EXT (1 << 3) +# define TBG_CNTRL_0_FRAME_DIS (1 << 5) +# define TBG_CNTRL_0_SYNC_MTHD (1 << 6) +# define TBG_CNTRL_0_SYNC_ONCE (1 << 7) +#define REG_TBG_CNTRL_1 REG(0x00, 0xcb) /* write */ +# define TBG_CNTRL_1_H_TGL (1 << 0) +# define TBG_CNTRL_1_V_TGL (1 << 1) +# define TBG_CNTRL_1_TGL_EN (1 << 2) +# define TBG_CNTRL_1_X_EXT (1 << 3) +# define TBG_CNTRL_1_H_EXT (1 << 4) +# define TBG_CNTRL_1_V_EXT (1 << 5) +# define TBG_CNTRL_1_DWIN_DIS (1 << 6) +#define REG_ENABLE_SPACE REG(0x00, 0xd6) /* write */ +#define REG_HVF_CNTRL_0 REG(0x00, 0xe4) /* write */ +# define HVF_CNTRL_0_SM (1 << 7) +# define HVF_CNTRL_0_RWB (1 << 6) +# define HVF_CNTRL_0_PREFIL(x) (((x) & 3) << 2) +# define HVF_CNTRL_0_INTPOL(x) (((x) & 3) << 0) +#define REG_HVF_CNTRL_1 REG(0x00, 0xe5) /* write */ +# define HVF_CNTRL_1_FOR (1 << 0) +# define HVF_CNTRL_1_YUVBLK (1 << 1) +# define HVF_CNTRL_1_VQR(x) (((x) & 3) << 2) +# define HVF_CNTRL_1_PAD(x) (((x) & 3) << 4) +# define HVF_CNTRL_1_SEMI_PLANAR (1 << 6) +#define REG_RPT_CNTRL REG(0x00, 0xf0) /* write */ +# define RPT_CNTRL_REPEAT(x) ((x) & 15) +#define REG_I2S_FORMAT REG(0x00, 0xfc) /* read/write */ +# define I2S_FORMAT_PHILIPS (0 << 0) +# define I2S_FORMAT_LEFT_J (2 << 0) +# define I2S_FORMAT_RIGHT_J (3 << 0) +#define REG_AIP_CLKSEL REG(0x00, 0xfd) /* write */ +# define AIP_CLKSEL_AIP_SPDIF (0 << 3) +# define AIP_CLKSEL_AIP_I2S (1 << 3) +# define AIP_CLKSEL_FS_ACLK (0 << 0) +# define AIP_CLKSEL_FS_MCLK (1 << 0) +# define AIP_CLKSEL_FS_FS64SPDIF (2 << 0) + +/* Page 02h: PLL settings */ +#define REG_PLL_SERIAL_1 REG(0x02, 0x00) /* read/write */ +# define PLL_SERIAL_1_SRL_FDN (1 << 0) +# define PLL_SERIAL_1_SRL_IZ(x) (((x) & 3) << 1) +# define PLL_SERIAL_1_SRL_MAN_IZ (1 << 6) +#define REG_PLL_SERIAL_2 REG(0x02, 0x01) /* read/write */ +# define PLL_SERIAL_2_SRL_NOSC(x) ((x) << 0) +# define PLL_SERIAL_2_SRL_PR(x) (((x) & 0xf) << 4) +#define REG_PLL_SERIAL_3 REG(0x02, 0x02) /* read/write */ +# define PLL_SERIAL_3_SRL_CCIR (1 << 0) +# define PLL_SERIAL_3_SRL_DE (1 << 2) +# define PLL_SERIAL_3_SRL_PXIN_SEL (1 << 4) +#define REG_SERIALIZER REG(0x02, 0x03) /* read/write */ +#define REG_BUFFER_OUT REG(0x02, 0x04) /* read/write */ +#define REG_PLL_SCG1 REG(0x02, 0x05) /* read/write */ +#define REG_PLL_SCG2 REG(0x02, 0x06) /* read/write */ +#define REG_PLL_SCGN1 REG(0x02, 0x07) /* read/write */ +#define REG_PLL_SCGN2 REG(0x02, 0x08) /* read/write */ +#define REG_PLL_SCGR1 REG(0x02, 0x09) /* read/write */ +#define REG_PLL_SCGR2 REG(0x02, 0x0a) /* read/write */ +#define REG_AUDIO_DIV REG(0x02, 0x0e) /* read/write */ +# define AUDIO_DIV_SERCLK_1 0 +# define AUDIO_DIV_SERCLK_2 1 +# define AUDIO_DIV_SERCLK_4 2 +# define AUDIO_DIV_SERCLK_8 3 +# define AUDIO_DIV_SERCLK_16 4 +# define AUDIO_DIV_SERCLK_32 5 +#define REG_SEL_CLK REG(0x02, 0x11) /* read/write */ +# define SEL_CLK_SEL_CLK1 (1 << 0) +# define SEL_CLK_SEL_VRF_CLK(x) (((x) & 3) << 1) +# define SEL_CLK_ENA_SC_CLK (1 << 3) +#define REG_ANA_GENERAL REG(0x02, 0x12) /* read/write */ + + +/* Page 09h: EDID Control */ +#define REG_EDID_DATA_0 REG(0x09, 0x00) /* read */ +/* next 127 successive registers are the EDID block */ +#define REG_EDID_CTRL REG(0x09, 0xfa) /* read/write */ +#define REG_DDC_ADDR REG(0x09, 0xfb) /* read/write */ +#define REG_DDC_OFFS REG(0x09, 0xfc) /* read/write */ +#define REG_DDC_SEGM_ADDR REG(0x09, 0xfd) /* read/write */ +#define REG_DDC_SEGM REG(0x09, 0xfe) /* read/write */ + + +/* Page 10h: information frames and packets */ +#define REG_IF1_HB0 REG(0x10, 0x20) /* read/write */ +#define REG_IF2_HB0 REG(0x10, 0x40) /* read/write */ +#define REG_IF3_HB0 REG(0x10, 0x60) /* read/write */ +#define REG_IF4_HB0 REG(0x10, 0x80) /* read/write */ +#define REG_IF5_HB0 REG(0x10, 0xa0) /* read/write */ + + +/* Page 11h: audio settings and content info packets */ +#define REG_AIP_CNTRL_0 REG(0x11, 0x00) /* read/write */ +# define AIP_CNTRL_0_RST_FIFO (1 << 0) +# define AIP_CNTRL_0_SWAP (1 << 1) +# define AIP_CNTRL_0_LAYOUT (1 << 2) +# define AIP_CNTRL_0_ACR_MAN (1 << 5) +# define AIP_CNTRL_0_RST_CTS (1 << 6) +#define REG_CA_I2S REG(0x11, 0x01) /* read/write */ +# define CA_I2S_CA_I2S(x) (((x) & 31) << 0) +# define CA_I2S_HBR_CHSTAT (1 << 6) +#define REG_LATENCY_RD REG(0x11, 0x04) /* read/write */ +#define REG_ACR_CTS_0 REG(0x11, 0x05) /* read/write */ +#define REG_ACR_CTS_1 REG(0x11, 0x06) /* read/write */ +#define REG_ACR_CTS_2 REG(0x11, 0x07) /* read/write */ +#define REG_ACR_N_0 REG(0x11, 0x08) /* read/write */ +#define REG_ACR_N_1 REG(0x11, 0x09) /* read/write */ +#define REG_ACR_N_2 REG(0x11, 0x0a) /* read/write */ +#define REG_CTS_N REG(0x11, 0x0c) /* read/write */ +# define CTS_N_K(x) (((x) & 7) << 0) +# define CTS_N_M(x) (((x) & 3) << 4) +#define REG_ENC_CNTRL REG(0x11, 0x0d) /* read/write */ +# define ENC_CNTRL_RST_ENC (1 << 0) +# define ENC_CNTRL_RST_SEL (1 << 1) +# define ENC_CNTRL_CTL_CODE(x) (((x) & 3) << 2) +#define REG_DIP_FLAGS REG(0x11, 0x0e) /* read/write */ +# define DIP_FLAGS_ACR (1 << 0) +# define DIP_FLAGS_GC (1 << 1) +#define REG_DIP_IF_FLAGS REG(0x11, 0x0f) /* read/write */ +# define DIP_IF_FLAGS_IF1 (1 << 1) +# define DIP_IF_FLAGS_IF2 (1 << 2) +# define DIP_IF_FLAGS_IF3 (1 << 3) +# define DIP_IF_FLAGS_IF4 (1 << 4) +# define DIP_IF_FLAGS_IF5 (1 << 5) +#define REG_CH_STAT_B(x) REG(0x11, 0x14 + (x)) /* read/write */ + + +/* Page 12h: HDCP and OTP */ +#define REG_TX3 REG(0x12, 0x9a) /* read/write */ +#define REG_TX4 REG(0x12, 0x9b) /* read/write */ +# define TX4_PD_RAM (1 << 1) +#define REG_TX33 REG(0x12, 0xb8) /* read/write */ +# define TX33_HDMI (1 << 1) + + +/* Page 13h: Gamut related metadata packets */ + + + +/* CEC registers: (not paged) + */ +#define REG_CEC_INTSTATUS 0xee /* read */ +# define CEC_INTSTATUS_CEC (1 << 0) +# define CEC_INTSTATUS_HDMI (1 << 1) +#define REG_CEC_CAL_XOSC_CTRL1 0xf2 +# define CEC_CAL_XOSC_CTRL1_ENA_CAL BIT(0) +#define REG_CEC_DES_FREQ2 0xf5 +# define CEC_DES_FREQ2_DIS_AUTOCAL BIT(7) +#define REG_CEC_CLK 0xf6 +# define CEC_CLK_FRO 0x11 +#define REG_CEC_FRO_IM_CLK_CTRL 0xfb /* read/write */ +# define CEC_FRO_IM_CLK_CTRL_GHOST_DIS (1 << 7) +# define CEC_FRO_IM_CLK_CTRL_ENA_OTP (1 << 6) +# define CEC_FRO_IM_CLK_CTRL_IMCLK_SEL (1 << 1) +# define CEC_FRO_IM_CLK_CTRL_FRO_DIV (1 << 0) +#define REG_CEC_RXSHPDINTENA 0xfc /* read/write */ +#define REG_CEC_RXSHPDINT 0xfd /* read */ +# define CEC_RXSHPDINT_RXSENS BIT(0) +# define CEC_RXSHPDINT_HPD BIT(1) +#define REG_CEC_RXSHPDLEV 0xfe /* read */ +# define CEC_RXSHPDLEV_RXSENS (1 << 0) +# define CEC_RXSHPDLEV_HPD (1 << 1) + +#define REG_CEC_ENAMODS 0xff /* read/write */ +# define CEC_ENAMODS_EN_CEC_CLK (1 << 7) +# define CEC_ENAMODS_DIS_FRO (1 << 6) +# define CEC_ENAMODS_DIS_CCLK (1 << 5) +# define CEC_ENAMODS_EN_RXSENS (1 << 2) +# define CEC_ENAMODS_EN_HDMI (1 << 1) +# define CEC_ENAMODS_EN_CEC (1 << 0) + + +/* Device versions: */ +#define TDA9989N2 0x0101 +#define TDA19989 0x0201 +#define TDA19989N2 0x0202 +#define TDA19988 0x0301 + +static void +cec_write(struct tda998x_priv *priv, u16 addr, u8 val) +{ + u8 buf[] = {addr, val}; + struct i2c_msg msg = { + .addr = priv->cec_addr, + .len = 2, + .buf = buf, + }; + int ret; + + ret = i2c_transfer(priv->hdmi->adapter, &msg, 1); + if (ret < 0) + dev_err(&priv->hdmi->dev, "Error %d writing to cec:0x%x\n", + ret, addr); +} + +static u8 +cec_read(struct tda998x_priv *priv, u8 addr) +{ + u8 val; + struct i2c_msg msg[2] = { + { + .addr = priv->cec_addr, + .len = 1, + .buf = &addr, + }, { + .addr = priv->cec_addr, + .flags = I2C_M_RD, + .len = 1, + .buf = &val, + }, + }; + int ret; + + ret = i2c_transfer(priv->hdmi->adapter, msg, ARRAY_SIZE(msg)); + if (ret < 0) { + dev_err(&priv->hdmi->dev, "Error %d reading from cec:0x%x\n", + ret, addr); + val = 0; + } + + return val; +} + +static void cec_enamods(struct tda998x_priv *priv, u8 mods, bool enable) +{ + int val = cec_read(priv, REG_CEC_ENAMODS); + + if (val < 0) + return; + + if (enable) + val |= mods; + else + val &= ~mods; + + cec_write(priv, REG_CEC_ENAMODS, val); +} + +static void tda998x_cec_set_calibration(struct tda998x_priv *priv, bool enable) +{ + if (enable) { + u8 val; + + cec_write(priv, 0xf3, 0xc0); + cec_write(priv, 0xf4, 0xd4); + + /* Enable automatic calibration mode */ + val = cec_read(priv, REG_CEC_DES_FREQ2); + val &= ~CEC_DES_FREQ2_DIS_AUTOCAL; + cec_write(priv, REG_CEC_DES_FREQ2, val); + + /* Enable free running oscillator */ + cec_write(priv, REG_CEC_CLK, CEC_CLK_FRO); + cec_enamods(priv, CEC_ENAMODS_DIS_FRO, false); + + cec_write(priv, REG_CEC_CAL_XOSC_CTRL1, + CEC_CAL_XOSC_CTRL1_ENA_CAL); + } else { + cec_write(priv, REG_CEC_CAL_XOSC_CTRL1, 0); + } +} + +/* + * Calibration for the internal oscillator: we need to set calibration mode, + * and then pulse the IRQ line low for a 10ms ± 1% period. + */ +static void tda998x_cec_calibration(struct tda998x_priv *priv) +{ + struct gpio_desc *calib = priv->calib; + + mutex_lock(&priv->edid_mutex); + if (priv->hdmi->irq > 0) + disable_irq(priv->hdmi->irq); + gpiod_direction_output(calib, 1); + tda998x_cec_set_calibration(priv, true); + + local_irq_disable(); + gpiod_set_value(calib, 0); + mdelay(10); + gpiod_set_value(calib, 1); + local_irq_enable(); + + tda998x_cec_set_calibration(priv, false); + gpiod_direction_input(calib); + if (priv->hdmi->irq > 0) + enable_irq(priv->hdmi->irq); + mutex_unlock(&priv->edid_mutex); +} + +static int tda998x_cec_hook_init(void *data) +{ + struct tda998x_priv *priv = data; + struct gpio_desc *calib; + + calib = gpiod_get(&priv->hdmi->dev, "nxp,calib", GPIOD_ASIS); + if (IS_ERR(calib)) { + dev_warn(&priv->hdmi->dev, "failed to get calibration gpio: %ld\n", + PTR_ERR(calib)); + return PTR_ERR(calib); + } + + priv->calib = calib; + + return 0; +} + +static void tda998x_cec_hook_exit(void *data) +{ + struct tda998x_priv *priv = data; + + gpiod_put(priv->calib); + priv->calib = NULL; +} + +static int tda998x_cec_hook_open(void *data) +{ + struct tda998x_priv *priv = data; + + cec_enamods(priv, CEC_ENAMODS_EN_CEC_CLK | CEC_ENAMODS_EN_CEC, true); + tda998x_cec_calibration(priv); + + return 0; +} + +static void tda998x_cec_hook_release(void *data) +{ + struct tda998x_priv *priv = data; + + cec_enamods(priv, CEC_ENAMODS_EN_CEC_CLK | CEC_ENAMODS_EN_CEC, false); +} + +static int +set_page(struct tda998x_priv *priv, u16 reg) +{ + if (REG2PAGE(reg) != priv->current_page) { + struct i2c_client *client = priv->hdmi; + u8 buf[] = { + REG_CURPAGE, REG2PAGE(reg) + }; + int ret = i2c_master_send(client, buf, sizeof(buf)); + if (ret < 0) { + dev_err(&client->dev, "%s %04x err %d\n", __func__, + reg, ret); + return ret; + } + + priv->current_page = REG2PAGE(reg); + } + return 0; +} + +static int +reg_read_range(struct tda998x_priv *priv, u16 reg, char *buf, int cnt) +{ + struct i2c_client *client = priv->hdmi; + u8 addr = REG2ADDR(reg); + int ret; + + mutex_lock(&priv->mutex); + ret = set_page(priv, reg); + if (ret < 0) + goto out; + + ret = i2c_master_send(client, &addr, sizeof(addr)); + if (ret < 0) + goto fail; + + ret = i2c_master_recv(client, buf, cnt); + if (ret < 0) + goto fail; + + goto out; + +fail: + dev_err(&client->dev, "Error %d reading from 0x%x\n", ret, reg); +out: + mutex_unlock(&priv->mutex); + return ret; +} + +#define MAX_WRITE_RANGE_BUF 32 + +static void +reg_write_range(struct tda998x_priv *priv, u16 reg, u8 *p, int cnt) +{ + struct i2c_client *client = priv->hdmi; + /* This is the maximum size of the buffer passed in */ + u8 buf[MAX_WRITE_RANGE_BUF + 1]; + int ret; + + if (cnt > MAX_WRITE_RANGE_BUF) { + dev_err(&client->dev, "Fixed write buffer too small (%d)\n", + MAX_WRITE_RANGE_BUF); + return; + } + + buf[0] = REG2ADDR(reg); + memcpy(&buf[1], p, cnt); + + mutex_lock(&priv->mutex); + ret = set_page(priv, reg); + if (ret < 0) + goto out; + + ret = i2c_master_send(client, buf, cnt + 1); + if (ret < 0) + dev_err(&client->dev, "Error %d writing to 0x%x\n", ret, reg); +out: + mutex_unlock(&priv->mutex); +} + +static int +reg_read(struct tda998x_priv *priv, u16 reg) +{ + u8 val = 0; + int ret; + + ret = reg_read_range(priv, reg, &val, sizeof(val)); + if (ret < 0) + return ret; + return val; +} + +static void +reg_write(struct tda998x_priv *priv, u16 reg, u8 val) +{ + struct i2c_client *client = priv->hdmi; + u8 buf[] = {REG2ADDR(reg), val}; + int ret; + + mutex_lock(&priv->mutex); + ret = set_page(priv, reg); + if (ret < 0) + goto out; + + ret = i2c_master_send(client, buf, sizeof(buf)); + if (ret < 0) + dev_err(&client->dev, "Error %d writing to 0x%x\n", ret, reg); +out: + mutex_unlock(&priv->mutex); +} + +static void +reg_write16(struct tda998x_priv *priv, u16 reg, u16 val) +{ + struct i2c_client *client = priv->hdmi; + u8 buf[] = {REG2ADDR(reg), val >> 8, val}; + int ret; + + mutex_lock(&priv->mutex); + ret = set_page(priv, reg); + if (ret < 0) + goto out; + + ret = i2c_master_send(client, buf, sizeof(buf)); + if (ret < 0) + dev_err(&client->dev, "Error %d writing to 0x%x\n", ret, reg); +out: + mutex_unlock(&priv->mutex); +} + +static void +reg_set(struct tda998x_priv *priv, u16 reg, u8 val) +{ + int old_val; + + old_val = reg_read(priv, reg); + if (old_val >= 0) + reg_write(priv, reg, old_val | val); +} + +static void +reg_clear(struct tda998x_priv *priv, u16 reg, u8 val) +{ + int old_val; + + old_val = reg_read(priv, reg); + if (old_val >= 0) + reg_write(priv, reg, old_val & ~val); +} + +static void +tda998x_reset(struct tda998x_priv *priv) +{ + /* reset audio and i2c master: */ + reg_write(priv, REG_SOFTRESET, SOFTRESET_AUDIO | SOFTRESET_I2C_MASTER); + msleep(50); + reg_write(priv, REG_SOFTRESET, 0); + msleep(50); + + /* reset transmitter: */ + reg_set(priv, REG_MAIN_CNTRL0, MAIN_CNTRL0_SR); + reg_clear(priv, REG_MAIN_CNTRL0, MAIN_CNTRL0_SR); + + /* PLL registers common configuration */ + reg_write(priv, REG_PLL_SERIAL_1, 0x00); + reg_write(priv, REG_PLL_SERIAL_2, PLL_SERIAL_2_SRL_NOSC(1)); + reg_write(priv, REG_PLL_SERIAL_3, 0x00); + reg_write(priv, REG_SERIALIZER, 0x00); + reg_write(priv, REG_BUFFER_OUT, 0x00); + reg_write(priv, REG_PLL_SCG1, 0x00); + reg_write(priv, REG_AUDIO_DIV, AUDIO_DIV_SERCLK_8); + reg_write(priv, REG_SEL_CLK, SEL_CLK_SEL_CLK1 | SEL_CLK_ENA_SC_CLK); + reg_write(priv, REG_PLL_SCGN1, 0xfa); + reg_write(priv, REG_PLL_SCGN2, 0x00); + reg_write(priv, REG_PLL_SCGR1, 0x5b); + reg_write(priv, REG_PLL_SCGR2, 0x00); + reg_write(priv, REG_PLL_SCG2, 0x10); + + /* Write the default value MUX register */ + reg_write(priv, REG_MUX_VP_VIP_OUT, 0x24); +} + +/* + * The TDA998x has a problem when trying to read the EDID close to a + * HPD assertion: it needs a delay of 100ms to avoid timing out while + * trying to read EDID data. + * + * However, tda998x_connector_get_modes() may be called at any moment + * after tda998x_connector_detect() indicates that we are connected, so + * we need to delay probing modes in tda998x_connector_get_modes() after + * we have seen a HPD inactive->active transition. This code implements + * that delay. + */ +static void tda998x_edid_delay_done(struct timer_list *t) +{ + struct tda998x_priv *priv = from_timer(priv, t, edid_delay_timer); + + priv->edid_delay_active = false; + wake_up(&priv->edid_delay_waitq); + schedule_work(&priv->detect_work); +} + +static void tda998x_edid_delay_start(struct tda998x_priv *priv) +{ + priv->edid_delay_active = true; + mod_timer(&priv->edid_delay_timer, jiffies + HZ/10); +} + +static int tda998x_edid_delay_wait(struct tda998x_priv *priv) +{ + return wait_event_killable(priv->edid_delay_waitq, !priv->edid_delay_active); +} + +/* + * We need to run the KMS hotplug event helper outside of our threaded + * interrupt routine as this can call back into our get_modes method, + * which will want to make use of interrupts. + */ +static void tda998x_detect_work(struct work_struct *work) +{ + struct tda998x_priv *priv = + container_of(work, struct tda998x_priv, detect_work); + struct drm_device *dev = priv->connector.dev; + + if (dev) + drm_kms_helper_hotplug_event(dev); +} + +/* + * only 2 interrupts may occur: screen plug/unplug and EDID read + */ +static irqreturn_t tda998x_irq_thread(int irq, void *data) +{ + struct tda998x_priv *priv = data; + u8 sta, cec, lvl, flag0, flag1, flag2; + bool handled = false; + + sta = cec_read(priv, REG_CEC_INTSTATUS); + if (sta & CEC_INTSTATUS_HDMI) { + cec = cec_read(priv, REG_CEC_RXSHPDINT); + lvl = cec_read(priv, REG_CEC_RXSHPDLEV); + flag0 = reg_read(priv, REG_INT_FLAGS_0); + flag1 = reg_read(priv, REG_INT_FLAGS_1); + flag2 = reg_read(priv, REG_INT_FLAGS_2); + DRM_DEBUG_DRIVER( + "tda irq sta %02x cec %02x lvl %02x f0 %02x f1 %02x f2 %02x\n", + sta, cec, lvl, flag0, flag1, flag2); + + if (cec & CEC_RXSHPDINT_HPD) { + if (lvl & CEC_RXSHPDLEV_HPD) { + tda998x_edid_delay_start(priv); + } else { + schedule_work(&priv->detect_work); + cec_notifier_phys_addr_invalidate( + priv->cec_notify); + } + + handled = true; + } + + if ((flag2 & INT_FLAGS_2_EDID_BLK_RD) && priv->wq_edid_wait) { + priv->wq_edid_wait = 0; + wake_up(&priv->wq_edid); + handled = true; + } + } + + return IRQ_RETVAL(handled); +} + +static void +tda998x_write_if(struct tda998x_priv *priv, u8 bit, u16 addr, + union hdmi_infoframe *frame) +{ + u8 buf[MAX_WRITE_RANGE_BUF]; + ssize_t len; + + len = hdmi_infoframe_pack(frame, buf, sizeof(buf)); + if (len < 0) { + dev_err(&priv->hdmi->dev, + "hdmi_infoframe_pack() type=0x%02x failed: %zd\n", + frame->any.type, len); + return; + } + + reg_clear(priv, REG_DIP_IF_FLAGS, bit); + reg_write_range(priv, addr, buf, len); + reg_set(priv, REG_DIP_IF_FLAGS, bit); +} + +static void tda998x_write_aif(struct tda998x_priv *priv, + const struct hdmi_audio_infoframe *cea) +{ + union hdmi_infoframe frame; + + frame.audio = *cea; + + tda998x_write_if(priv, DIP_IF_FLAGS_IF4, REG_IF4_HB0, &frame); +} + +static void +tda998x_write_avi(struct tda998x_priv *priv, const struct drm_display_mode *mode) +{ + union hdmi_infoframe frame; + + drm_hdmi_avi_infoframe_from_display_mode(&frame.avi, + &priv->connector, mode); + frame.avi.quantization_range = HDMI_QUANTIZATION_RANGE_FULL; + drm_hdmi_avi_infoframe_quant_range(&frame.avi, &priv->connector, mode, + priv->rgb_quant_range); + + tda998x_write_if(priv, DIP_IF_FLAGS_IF2, REG_IF2_HB0, &frame); +} + +static void tda998x_write_vsi(struct tda998x_priv *priv, + const struct drm_display_mode *mode) +{ + union hdmi_infoframe frame; + + if (drm_hdmi_vendor_infoframe_from_display_mode(&frame.vendor.hdmi, + &priv->connector, + mode)) + reg_clear(priv, REG_DIP_IF_FLAGS, DIP_IF_FLAGS_IF1); + else + tda998x_write_if(priv, DIP_IF_FLAGS_IF1, REG_IF1_HB0, &frame); +} + +/* Audio support */ + +static const struct tda998x_audio_route tda998x_audio_route[AUDIO_ROUTE_NUM] = { + [AUDIO_ROUTE_I2S] = { + .ena_aclk = 1, + .mux_ap = MUX_AP_SELECT_I2S, + .aip_clksel = AIP_CLKSEL_AIP_I2S | AIP_CLKSEL_FS_ACLK, + }, + [AUDIO_ROUTE_SPDIF] = { + .ena_aclk = 0, + .mux_ap = MUX_AP_SELECT_SPDIF, + .aip_clksel = AIP_CLKSEL_AIP_SPDIF | AIP_CLKSEL_FS_FS64SPDIF, + }, +}; + +/* Configure the TDA998x audio data and clock routing. */ +static int tda998x_derive_routing(struct tda998x_priv *priv, + struct tda998x_audio_settings *s, + unsigned int route) +{ + s->route = &tda998x_audio_route[route]; + s->ena_ap = priv->audio_port_enable[route]; + if (s->ena_ap == 0) { + dev_err(&priv->hdmi->dev, "no audio configuration found\n"); + return -EINVAL; + } + + return 0; +} + +/* + * The audio clock divisor register controls a divider producing Audio_Clk_Out + * from SERclk by dividing it by 2^n where 0 <= n <= 5. We don't know what + * Audio_Clk_Out or SERclk are. We guess SERclk is the same as TMDS clock. + * + * It seems that Audio_Clk_Out must be the smallest value that is greater + * than 128*fs, otherwise audio does not function. There is some suggestion + * that 126*fs is a better value. + */ +static u8 tda998x_get_adiv(struct tda998x_priv *priv, unsigned int fs) +{ + unsigned long min_audio_clk = fs * 128; + unsigned long ser_clk = priv->tmds_clock * 1000; + u8 adiv; + + for (adiv = AUDIO_DIV_SERCLK_32; adiv != AUDIO_DIV_SERCLK_1; adiv--) + if (ser_clk > min_audio_clk << adiv) + break; + + dev_dbg(&priv->hdmi->dev, + "ser_clk=%luHz fs=%uHz min_aclk=%luHz adiv=%d\n", + ser_clk, fs, min_audio_clk, adiv); + + return adiv; +} + +/* + * In auto-CTS mode, the TDA998x uses a "measured time stamp" counter to + * generate the CTS value. It appears that the "measured time stamp" is + * the number of TDMS clock cycles within a number of audio input clock + * cycles defined by the k and N parameters defined below, in a similar + * way to that which is set out in the CTS generation in the HDMI spec. + * + * tmdsclk ----> mts -> /m ---> CTS + * ^ + * sclk -> /k -> /N + * + * CTS = mts / m, where m is 2^M. + * /k is a divider based on the K value below, K+1 for K < 4, or 8 for K >= 4 + * /N is a divider based on the HDMI specified N value. + * + * This produces the following equation: + * CTS = tmds_clock * k * N / (sclk * m) + * + * When combined with the sink-side equation, and realising that sclk is + * bclk_ratio * fs, we end up with: + * k = m * bclk_ratio / 128. + * + * Note: S/PDIF always uses a bclk_ratio of 64. + */ +static int tda998x_derive_cts_n(struct tda998x_priv *priv, + struct tda998x_audio_settings *settings, + unsigned int ratio) +{ + switch (ratio) { + case 16: + settings->cts_n = CTS_N_M(3) | CTS_N_K(0); + break; + case 32: + settings->cts_n = CTS_N_M(3) | CTS_N_K(1); + break; + case 48: + settings->cts_n = CTS_N_M(3) | CTS_N_K(2); + break; + case 64: + settings->cts_n = CTS_N_M(3) | CTS_N_K(3); + break; + case 128: + settings->cts_n = CTS_N_M(0) | CTS_N_K(0); + break; + default: + dev_err(&priv->hdmi->dev, "unsupported bclk ratio %ufs\n", + ratio); + return -EINVAL; + } + return 0; +} + +static void tda998x_audio_mute(struct tda998x_priv *priv, bool on) +{ + if (on) { + reg_set(priv, REG_SOFTRESET, SOFTRESET_AUDIO); + reg_clear(priv, REG_SOFTRESET, SOFTRESET_AUDIO); + reg_set(priv, REG_AIP_CNTRL_0, AIP_CNTRL_0_RST_FIFO); + } else { + reg_clear(priv, REG_AIP_CNTRL_0, AIP_CNTRL_0_RST_FIFO); + } +} + +static void tda998x_configure_audio(struct tda998x_priv *priv) +{ + const struct tda998x_audio_settings *settings = &priv->audio; + u8 buf[6], adiv; + u32 n; + + /* If audio is not configured, there is nothing to do. */ + if (settings->ena_ap == 0) + return; + + adiv = tda998x_get_adiv(priv, settings->sample_rate); + + /* Enable audio ports */ + reg_write(priv, REG_ENA_AP, settings->ena_ap); + reg_write(priv, REG_ENA_ACLK, settings->route->ena_aclk); + reg_write(priv, REG_MUX_AP, settings->route->mux_ap); + reg_write(priv, REG_I2S_FORMAT, settings->i2s_format); + reg_write(priv, REG_AIP_CLKSEL, settings->route->aip_clksel); + reg_clear(priv, REG_AIP_CNTRL_0, AIP_CNTRL_0_LAYOUT | + AIP_CNTRL_0_ACR_MAN); /* auto CTS */ + reg_write(priv, REG_CTS_N, settings->cts_n); + reg_write(priv, REG_AUDIO_DIV, adiv); + + /* + * This is the approximate value of N, which happens to be + * the recommended values for non-coherent clocks. + */ + n = 128 * settings->sample_rate / 1000; + + /* Write the CTS and N values */ + buf[0] = 0x44; + buf[1] = 0x42; + buf[2] = 0x01; + buf[3] = n; + buf[4] = n >> 8; + buf[5] = n >> 16; + reg_write_range(priv, REG_ACR_CTS_0, buf, 6); + + /* Reset CTS generator */ + reg_set(priv, REG_AIP_CNTRL_0, AIP_CNTRL_0_RST_CTS); + reg_clear(priv, REG_AIP_CNTRL_0, AIP_CNTRL_0_RST_CTS); + + /* Write the channel status + * The REG_CH_STAT_B-registers skip IEC958 AES2 byte, because + * there is a separate register for each I2S wire. + */ + buf[0] = settings->status[0]; + buf[1] = settings->status[1]; + buf[2] = settings->status[3]; + buf[3] = settings->status[4]; + reg_write_range(priv, REG_CH_STAT_B(0), buf, 4); + + tda998x_audio_mute(priv, true); + msleep(20); + tda998x_audio_mute(priv, false); + + tda998x_write_aif(priv, &settings->cea); +} + +static int tda998x_audio_hw_params(struct device *dev, void *data, + struct hdmi_codec_daifmt *daifmt, + struct hdmi_codec_params *params) +{ + struct tda998x_priv *priv = dev_get_drvdata(dev); + unsigned int bclk_ratio; + bool spdif = daifmt->fmt == HDMI_SPDIF; + int ret; + struct tda998x_audio_settings audio = { + .sample_rate = params->sample_rate, + .cea = params->cea, + }; + + memcpy(audio.status, params->iec.status, + min(sizeof(audio.status), sizeof(params->iec.status))); + + switch (daifmt->fmt) { + case HDMI_I2S: + audio.i2s_format = I2S_FORMAT_PHILIPS; + break; + case HDMI_LEFT_J: + audio.i2s_format = I2S_FORMAT_LEFT_J; + break; + case HDMI_RIGHT_J: + audio.i2s_format = I2S_FORMAT_RIGHT_J; + break; + case HDMI_SPDIF: + audio.i2s_format = 0; + break; + default: + dev_err(dev, "%s: Invalid format %d\n", __func__, daifmt->fmt); + return -EINVAL; + } + + if (!spdif && + (daifmt->bit_clk_inv || daifmt->frame_clk_inv || + daifmt->bit_clk_provider || daifmt->frame_clk_provider)) { + dev_err(dev, "%s: Bad flags %d %d %d %d\n", __func__, + daifmt->bit_clk_inv, daifmt->frame_clk_inv, + daifmt->bit_clk_provider, + daifmt->frame_clk_provider); + return -EINVAL; + } + + ret = tda998x_derive_routing(priv, &audio, AUDIO_ROUTE_I2S + spdif); + if (ret < 0) + return ret; + + bclk_ratio = spdif ? 64 : params->sample_width * 2; + ret = tda998x_derive_cts_n(priv, &audio, bclk_ratio); + if (ret < 0) + return ret; + + mutex_lock(&priv->audio_mutex); + priv->audio = audio; + if (priv->supports_infoframes && priv->sink_has_audio) + tda998x_configure_audio(priv); + mutex_unlock(&priv->audio_mutex); + + return 0; +} + +static void tda998x_audio_shutdown(struct device *dev, void *data) +{ + struct tda998x_priv *priv = dev_get_drvdata(dev); + + mutex_lock(&priv->audio_mutex); + + reg_write(priv, REG_ENA_AP, 0); + priv->audio.ena_ap = 0; + + mutex_unlock(&priv->audio_mutex); +} + +static int tda998x_audio_mute_stream(struct device *dev, void *data, + bool enable, int direction) +{ + struct tda998x_priv *priv = dev_get_drvdata(dev); + + mutex_lock(&priv->audio_mutex); + + tda998x_audio_mute(priv, enable); + + mutex_unlock(&priv->audio_mutex); + return 0; +} + +static int tda998x_audio_get_eld(struct device *dev, void *data, + uint8_t *buf, size_t len) +{ + struct tda998x_priv *priv = dev_get_drvdata(dev); + + mutex_lock(&priv->audio_mutex); + memcpy(buf, priv->connector.eld, + min(sizeof(priv->connector.eld), len)); + mutex_unlock(&priv->audio_mutex); + + return 0; +} + +static const struct hdmi_codec_ops audio_codec_ops = { + .hw_params = tda998x_audio_hw_params, + .audio_shutdown = tda998x_audio_shutdown, + .mute_stream = tda998x_audio_mute_stream, + .get_eld = tda998x_audio_get_eld, + .no_capture_mute = 1, +}; + +static int tda998x_audio_codec_init(struct tda998x_priv *priv, + struct device *dev) +{ + struct hdmi_codec_pdata codec_data = { + .ops = &audio_codec_ops, + .max_i2s_channels = 2, + }; + + if (priv->audio_port_enable[AUDIO_ROUTE_I2S]) + codec_data.i2s = 1; + if (priv->audio_port_enable[AUDIO_ROUTE_SPDIF]) + codec_data.spdif = 1; + + priv->audio_pdev = platform_device_register_data( + dev, HDMI_CODEC_DRV_NAME, PLATFORM_DEVID_AUTO, + &codec_data, sizeof(codec_data)); + + return PTR_ERR_OR_ZERO(priv->audio_pdev); +} + +/* DRM connector functions */ + +static enum drm_connector_status +tda998x_connector_detect(struct drm_connector *connector, bool force) +{ + struct tda998x_priv *priv = conn_to_tda998x_priv(connector); + u8 val = cec_read(priv, REG_CEC_RXSHPDLEV); + + return (val & CEC_RXSHPDLEV_HPD) ? connector_status_connected : + connector_status_disconnected; +} + +static void tda998x_connector_destroy(struct drm_connector *connector) +{ + drm_connector_cleanup(connector); +} + +static const struct drm_connector_funcs tda998x_connector_funcs = { + .reset = drm_atomic_helper_connector_reset, + .fill_modes = drm_helper_probe_single_connector_modes, + .detect = tda998x_connector_detect, + .destroy = tda998x_connector_destroy, + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, +}; + +static int read_edid_block(void *data, u8 *buf, unsigned int blk, size_t length) +{ + struct tda998x_priv *priv = data; + u8 offset, segptr; + int ret, i; + + offset = (blk & 1) ? 128 : 0; + segptr = blk / 2; + + mutex_lock(&priv->edid_mutex); + + reg_write(priv, REG_DDC_ADDR, 0xa0); + reg_write(priv, REG_DDC_OFFS, offset); + reg_write(priv, REG_DDC_SEGM_ADDR, 0x60); + reg_write(priv, REG_DDC_SEGM, segptr); + + /* enable reading EDID: */ + priv->wq_edid_wait = 1; + reg_write(priv, REG_EDID_CTRL, 0x1); + + /* flag must be cleared by sw: */ + reg_write(priv, REG_EDID_CTRL, 0x0); + + /* wait for block read to complete: */ + if (priv->hdmi->irq) { + i = wait_event_timeout(priv->wq_edid, + !priv->wq_edid_wait, + msecs_to_jiffies(100)); + if (i < 0) { + dev_err(&priv->hdmi->dev, "read edid wait err %d\n", i); + ret = i; + goto failed; + } + } else { + for (i = 100; i > 0; i--) { + msleep(1); + ret = reg_read(priv, REG_INT_FLAGS_2); + if (ret < 0) + goto failed; + if (ret & INT_FLAGS_2_EDID_BLK_RD) + break; + } + } + + if (i == 0) { + dev_err(&priv->hdmi->dev, "read edid timeout\n"); + ret = -ETIMEDOUT; + goto failed; + } + + ret = reg_read_range(priv, REG_EDID_DATA_0, buf, length); + if (ret != length) { + dev_err(&priv->hdmi->dev, "failed to read edid block %d: %d\n", + blk, ret); + goto failed; + } + + ret = 0; + + failed: + mutex_unlock(&priv->edid_mutex); + return ret; +} + +static int tda998x_connector_get_modes(struct drm_connector *connector) +{ + struct tda998x_priv *priv = conn_to_tda998x_priv(connector); + struct edid *edid; + int n; + + /* + * If we get killed while waiting for the HPD timeout, return + * no modes found: we are not in a restartable path, so we + * can't handle signals gracefully. + */ + if (tda998x_edid_delay_wait(priv)) + return 0; + + if (priv->rev == TDA19988) + reg_clear(priv, REG_TX4, TX4_PD_RAM); + + edid = drm_do_get_edid(connector, read_edid_block, priv); + + if (priv->rev == TDA19988) + reg_set(priv, REG_TX4, TX4_PD_RAM); + + if (!edid) { + dev_warn(&priv->hdmi->dev, "failed to read EDID\n"); + return 0; + } + + drm_connector_update_edid_property(connector, edid); + cec_notifier_set_phys_addr_from_edid(priv->cec_notify, edid); + + mutex_lock(&priv->audio_mutex); + n = drm_add_edid_modes(connector, edid); + priv->sink_has_audio = drm_detect_monitor_audio(edid); + mutex_unlock(&priv->audio_mutex); + + kfree(edid); + + return n; +} + +static struct drm_encoder * +tda998x_connector_best_encoder(struct drm_connector *connector) +{ + struct tda998x_priv *priv = conn_to_tda998x_priv(connector); + + return priv->bridge.encoder; +} + +static +const struct drm_connector_helper_funcs tda998x_connector_helper_funcs = { + .get_modes = tda998x_connector_get_modes, + .best_encoder = tda998x_connector_best_encoder, +}; + +static int tda998x_connector_init(struct tda998x_priv *priv, + struct drm_device *drm) +{ + struct drm_connector *connector = &priv->connector; + int ret; + + connector->interlace_allowed = 1; + + if (priv->hdmi->irq) + connector->polled = DRM_CONNECTOR_POLL_HPD; + else + connector->polled = DRM_CONNECTOR_POLL_CONNECT | + DRM_CONNECTOR_POLL_DISCONNECT; + + drm_connector_helper_add(connector, &tda998x_connector_helper_funcs); + ret = drm_connector_init(drm, connector, &tda998x_connector_funcs, + DRM_MODE_CONNECTOR_HDMIA); + if (ret) + return ret; + + drm_connector_attach_encoder(&priv->connector, + priv->bridge.encoder); + + return 0; +} + +/* DRM bridge functions */ + +static int tda998x_bridge_attach(struct drm_bridge *bridge, + enum drm_bridge_attach_flags flags) +{ + struct tda998x_priv *priv = bridge_to_tda998x_priv(bridge); + + if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR) { + DRM_ERROR("Fix bridge driver to make connector optional!"); + return -EINVAL; + } + + return tda998x_connector_init(priv, bridge->dev); +} + +static void tda998x_bridge_detach(struct drm_bridge *bridge) +{ + struct tda998x_priv *priv = bridge_to_tda998x_priv(bridge); + + drm_connector_cleanup(&priv->connector); +} + +static enum drm_mode_status tda998x_bridge_mode_valid(struct drm_bridge *bridge, + const struct drm_display_info *info, + const struct drm_display_mode *mode) +{ + /* TDA19988 dotclock can go up to 165MHz */ + struct tda998x_priv *priv = bridge_to_tda998x_priv(bridge); + + if (mode->clock > ((priv->rev == TDA19988) ? 165000 : 150000)) + return MODE_CLOCK_HIGH; + if (mode->htotal >= BIT(13)) + return MODE_BAD_HVALUE; + if (mode->vtotal >= BIT(11)) + return MODE_BAD_VVALUE; + return MODE_OK; +} + +static void tda998x_bridge_enable(struct drm_bridge *bridge) +{ + struct tda998x_priv *priv = bridge_to_tda998x_priv(bridge); + + if (!priv->is_on) { + /* enable video ports, audio will be enabled later */ + reg_write(priv, REG_ENA_VP_0, 0xff); + reg_write(priv, REG_ENA_VP_1, 0xff); + reg_write(priv, REG_ENA_VP_2, 0xff); + /* set muxing after enabling ports: */ + reg_write(priv, REG_VIP_CNTRL_0, priv->vip_cntrl_0); + reg_write(priv, REG_VIP_CNTRL_1, priv->vip_cntrl_1); + reg_write(priv, REG_VIP_CNTRL_2, priv->vip_cntrl_2); + + priv->is_on = true; + } +} + +static void tda998x_bridge_disable(struct drm_bridge *bridge) +{ + struct tda998x_priv *priv = bridge_to_tda998x_priv(bridge); + + if (priv->is_on) { + /* disable video ports */ + reg_write(priv, REG_ENA_VP_0, 0x00); + reg_write(priv, REG_ENA_VP_1, 0x00); + reg_write(priv, REG_ENA_VP_2, 0x00); + + priv->is_on = false; + } +} + +static void tda998x_bridge_mode_set(struct drm_bridge *bridge, + const struct drm_display_mode *mode, + const struct drm_display_mode *adjusted_mode) +{ + struct tda998x_priv *priv = bridge_to_tda998x_priv(bridge); + unsigned long tmds_clock; + u16 ref_pix, ref_line, n_pix, n_line; + u16 hs_pix_s, hs_pix_e; + u16 vs1_pix_s, vs1_pix_e, vs1_line_s, vs1_line_e; + u16 vs2_pix_s, vs2_pix_e, vs2_line_s, vs2_line_e; + u16 vwin1_line_s, vwin1_line_e; + u16 vwin2_line_s, vwin2_line_e; + u16 de_pix_s, de_pix_e; + u8 reg, div, rep, sel_clk; + + /* + * Since we are "computer" like, our source invariably produces + * full-range RGB. If the monitor supports full-range, then use + * it, otherwise reduce to limited-range. + */ + priv->rgb_quant_range = + priv->connector.display_info.rgb_quant_range_selectable ? + HDMI_QUANTIZATION_RANGE_FULL : + drm_default_rgb_quant_range(adjusted_mode); + + /* + * Internally TDA998x is using ITU-R BT.656 style sync but + * we get VESA style sync. TDA998x is using a reference pixel + * relative to ITU to sync to the input frame and for output + * sync generation. Currently, we are using reference detection + * from HS/VS, i.e. REFPIX/REFLINE denote frame start sync point + * which is position of rising VS with coincident rising HS. + * + * Now there is some issues to take care of: + * - HDMI data islands require sync-before-active + * - TDA998x register values must be > 0 to be enabled + * - REFLINE needs an additional offset of +1 + * - REFPIX needs an addtional offset of +1 for UYUV and +3 for RGB + * + * So we add +1 to all horizontal and vertical register values, + * plus an additional +3 for REFPIX as we are using RGB input only. + */ + n_pix = mode->htotal; + n_line = mode->vtotal; + + hs_pix_e = mode->hsync_end - mode->hdisplay; + hs_pix_s = mode->hsync_start - mode->hdisplay; + de_pix_e = mode->htotal; + de_pix_s = mode->htotal - mode->hdisplay; + ref_pix = 3 + hs_pix_s; + + /* + * Attached LCD controllers may generate broken sync. Allow + * those to adjust the position of the rising VS edge by adding + * HSKEW to ref_pix. + */ + if (adjusted_mode->flags & DRM_MODE_FLAG_HSKEW) + ref_pix += adjusted_mode->hskew; + + if ((mode->flags & DRM_MODE_FLAG_INTERLACE) == 0) { + ref_line = 1 + mode->vsync_start - mode->vdisplay; + vwin1_line_s = mode->vtotal - mode->vdisplay - 1; + vwin1_line_e = vwin1_line_s + mode->vdisplay; + vs1_pix_s = vs1_pix_e = hs_pix_s; + vs1_line_s = mode->vsync_start - mode->vdisplay; + vs1_line_e = vs1_line_s + + mode->vsync_end - mode->vsync_start; + vwin2_line_s = vwin2_line_e = 0; + vs2_pix_s = vs2_pix_e = 0; + vs2_line_s = vs2_line_e = 0; + } else { + ref_line = 1 + (mode->vsync_start - mode->vdisplay)/2; + vwin1_line_s = (mode->vtotal - mode->vdisplay)/2; + vwin1_line_e = vwin1_line_s + mode->vdisplay/2; + vs1_pix_s = vs1_pix_e = hs_pix_s; + vs1_line_s = (mode->vsync_start - mode->vdisplay)/2; + vs1_line_e = vs1_line_s + + (mode->vsync_end - mode->vsync_start)/2; + vwin2_line_s = vwin1_line_s + mode->vtotal/2; + vwin2_line_e = vwin2_line_s + mode->vdisplay/2; + vs2_pix_s = vs2_pix_e = hs_pix_s + mode->htotal/2; + vs2_line_s = vs1_line_s + mode->vtotal/2 ; + vs2_line_e = vs2_line_s + + (mode->vsync_end - mode->vsync_start)/2; + } + + /* + * Select pixel repeat depending on the double-clock flag + * (which means we have to repeat each pixel once.) + */ + rep = mode->flags & DRM_MODE_FLAG_DBLCLK ? 1 : 0; + sel_clk = SEL_CLK_ENA_SC_CLK | SEL_CLK_SEL_CLK1 | + SEL_CLK_SEL_VRF_CLK(rep ? 2 : 0); + + /* the TMDS clock is scaled up by the pixel repeat */ + tmds_clock = mode->clock * (1 + rep); + + /* + * The divisor is power-of-2. The TDA9983B datasheet gives + * this as ranges of Msample/s, which is 10x the TMDS clock: + * 0 - 800 to 1500 Msample/s + * 1 - 400 to 800 Msample/s + * 2 - 200 to 400 Msample/s + * 3 - as 2 above + */ + for (div = 0; div < 3; div++) + if (80000 >> div <= tmds_clock) + break; + + mutex_lock(&priv->audio_mutex); + + priv->tmds_clock = tmds_clock; + + /* mute the audio FIFO: */ + reg_set(priv, REG_AIP_CNTRL_0, AIP_CNTRL_0_RST_FIFO); + + /* set HDMI HDCP mode off: */ + reg_write(priv, REG_TBG_CNTRL_1, TBG_CNTRL_1_DWIN_DIS); + reg_clear(priv, REG_TX33, TX33_HDMI); + reg_write(priv, REG_ENC_CNTRL, ENC_CNTRL_CTL_CODE(0)); + + /* no pre-filter or interpolator: */ + reg_write(priv, REG_HVF_CNTRL_0, HVF_CNTRL_0_PREFIL(0) | + HVF_CNTRL_0_INTPOL(0)); + reg_set(priv, REG_FEAT_POWERDOWN, FEAT_POWERDOWN_PREFILT); + reg_write(priv, REG_VIP_CNTRL_5, VIP_CNTRL_5_SP_CNT(0)); + reg_write(priv, REG_VIP_CNTRL_4, VIP_CNTRL_4_BLANKIT(0) | + VIP_CNTRL_4_BLC(0)); + + reg_clear(priv, REG_PLL_SERIAL_1, PLL_SERIAL_1_SRL_MAN_IZ); + reg_clear(priv, REG_PLL_SERIAL_3, PLL_SERIAL_3_SRL_CCIR | + PLL_SERIAL_3_SRL_DE); + reg_write(priv, REG_SERIALIZER, 0); + reg_write(priv, REG_HVF_CNTRL_1, HVF_CNTRL_1_VQR(0)); + + reg_write(priv, REG_RPT_CNTRL, RPT_CNTRL_REPEAT(rep)); + reg_write(priv, REG_SEL_CLK, sel_clk); + reg_write(priv, REG_PLL_SERIAL_2, PLL_SERIAL_2_SRL_NOSC(div) | + PLL_SERIAL_2_SRL_PR(rep)); + + /* set color matrix according to output rgb quant range */ + if (priv->rgb_quant_range == HDMI_QUANTIZATION_RANGE_LIMITED) { + static u8 tda998x_full_to_limited_range[] = { + MAT_CONTRL_MAT_SC(2), + 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + 0x03, 0x6f, 0x00, 0x00, 0x00, 0x00, + 0x00, 0x00, 0x03, 0x6f, 0x00, 0x00, + 0x00, 0x00, 0x00, 0x00, 0x03, 0x6f, + 0x00, 0x40, 0x00, 0x40, 0x00, 0x40 + }; + reg_clear(priv, REG_FEAT_POWERDOWN, FEAT_POWERDOWN_CSC); + reg_write_range(priv, REG_MAT_CONTRL, + tda998x_full_to_limited_range, + sizeof(tda998x_full_to_limited_range)); + } else { + reg_write(priv, REG_MAT_CONTRL, MAT_CONTRL_MAT_BP | + MAT_CONTRL_MAT_SC(1)); + reg_set(priv, REG_FEAT_POWERDOWN, FEAT_POWERDOWN_CSC); + } + + /* set BIAS tmds value: */ + reg_write(priv, REG_ANA_GENERAL, 0x09); + + /* + * Sync on rising HSYNC/VSYNC + */ + reg = VIP_CNTRL_3_SYNC_HS; + + /* + * TDA19988 requires high-active sync at input stage, + * so invert low-active sync provided by master encoder here + */ + if (mode->flags & DRM_MODE_FLAG_NHSYNC) + reg |= VIP_CNTRL_3_H_TGL; + if (mode->flags & DRM_MODE_FLAG_NVSYNC) + reg |= VIP_CNTRL_3_V_TGL; + reg_write(priv, REG_VIP_CNTRL_3, reg); + + reg_write(priv, REG_VIDFORMAT, 0x00); + reg_write16(priv, REG_REFPIX_MSB, ref_pix); + reg_write16(priv, REG_REFLINE_MSB, ref_line); + reg_write16(priv, REG_NPIX_MSB, n_pix); + reg_write16(priv, REG_NLINE_MSB, n_line); + reg_write16(priv, REG_VS_LINE_STRT_1_MSB, vs1_line_s); + reg_write16(priv, REG_VS_PIX_STRT_1_MSB, vs1_pix_s); + reg_write16(priv, REG_VS_LINE_END_1_MSB, vs1_line_e); + reg_write16(priv, REG_VS_PIX_END_1_MSB, vs1_pix_e); + reg_write16(priv, REG_VS_LINE_STRT_2_MSB, vs2_line_s); + reg_write16(priv, REG_VS_PIX_STRT_2_MSB, vs2_pix_s); + reg_write16(priv, REG_VS_LINE_END_2_MSB, vs2_line_e); + reg_write16(priv, REG_VS_PIX_END_2_MSB, vs2_pix_e); + reg_write16(priv, REG_HS_PIX_START_MSB, hs_pix_s); + reg_write16(priv, REG_HS_PIX_STOP_MSB, hs_pix_e); + reg_write16(priv, REG_VWIN_START_1_MSB, vwin1_line_s); + reg_write16(priv, REG_VWIN_END_1_MSB, vwin1_line_e); + reg_write16(priv, REG_VWIN_START_2_MSB, vwin2_line_s); + reg_write16(priv, REG_VWIN_END_2_MSB, vwin2_line_e); + reg_write16(priv, REG_DE_START_MSB, de_pix_s); + reg_write16(priv, REG_DE_STOP_MSB, de_pix_e); + + if (priv->rev == TDA19988) { + /* let incoming pixels fill the active space (if any) */ + reg_write(priv, REG_ENABLE_SPACE, 0x00); + } + + /* + * Always generate sync polarity relative to input sync and + * revert input stage toggled sync at output stage + */ + reg = TBG_CNTRL_1_DWIN_DIS | TBG_CNTRL_1_TGL_EN; + if (mode->flags & DRM_MODE_FLAG_NHSYNC) + reg |= TBG_CNTRL_1_H_TGL; + if (mode->flags & DRM_MODE_FLAG_NVSYNC) + reg |= TBG_CNTRL_1_V_TGL; + reg_write(priv, REG_TBG_CNTRL_1, reg); + + /* must be last register set: */ + reg_write(priv, REG_TBG_CNTRL_0, 0); + + /* CEA-861B section 6 says that: + * CEA version 1 (CEA-861) has no support for infoframes. + * CEA version 2 (CEA-861A) supports version 1 AVI infoframes, + * and optional basic audio. + * CEA version 3 (CEA-861B) supports version 1 and 2 AVI infoframes, + * and optional digital audio, with audio infoframes. + * + * Since we only support generation of version 2 AVI infoframes, + * ignore CEA version 2 and below (iow, behave as if we're a + * CEA-861 source.) + */ + priv->supports_infoframes = priv->connector.display_info.cea_rev >= 3; + + if (priv->supports_infoframes) { + /* We need to turn HDMI HDCP stuff on to get audio through */ + reg &= ~TBG_CNTRL_1_DWIN_DIS; + reg_write(priv, REG_TBG_CNTRL_1, reg); + reg_write(priv, REG_ENC_CNTRL, ENC_CNTRL_CTL_CODE(1)); + reg_set(priv, REG_TX33, TX33_HDMI); + + tda998x_write_avi(priv, adjusted_mode); + tda998x_write_vsi(priv, adjusted_mode); + + if (priv->sink_has_audio) + tda998x_configure_audio(priv); + } + + mutex_unlock(&priv->audio_mutex); +} + +static const struct drm_bridge_funcs tda998x_bridge_funcs = { + .attach = tda998x_bridge_attach, + .detach = tda998x_bridge_detach, + .mode_valid = tda998x_bridge_mode_valid, + .disable = tda998x_bridge_disable, + .mode_set = tda998x_bridge_mode_set, + .enable = tda998x_bridge_enable, +}; + +/* I2C driver functions */ + +static int tda998x_get_audio_ports(struct tda998x_priv *priv, + struct device_node *np) +{ + const u32 *port_data; + u32 size; + int i; + + port_data = of_get_property(np, "audio-ports", &size); + if (!port_data) + return 0; + + size /= sizeof(u32); + if (size > 2 * ARRAY_SIZE(priv->audio_port_enable) || size % 2 != 0) { + dev_err(&priv->hdmi->dev, + "Bad number of elements in audio-ports dt-property\n"); + return -EINVAL; + } + + size /= 2; + + for (i = 0; i < size; i++) { + unsigned int route; + u8 afmt = be32_to_cpup(&port_data[2*i]); + u8 ena_ap = be32_to_cpup(&port_data[2*i+1]); + + switch (afmt) { + case AFMT_I2S: + route = AUDIO_ROUTE_I2S; + break; + case AFMT_SPDIF: + route = AUDIO_ROUTE_SPDIF; + break; + default: + dev_err(&priv->hdmi->dev, + "Bad audio format %u\n", afmt); + return -EINVAL; + } + + if (!ena_ap) { + dev_err(&priv->hdmi->dev, "invalid zero port config\n"); + continue; + } + + if (priv->audio_port_enable[route]) { + dev_err(&priv->hdmi->dev, + "%s format already configured\n", + route == AUDIO_ROUTE_SPDIF ? "SPDIF" : "I2S"); + return -EINVAL; + } + + priv->audio_port_enable[route] = ena_ap; + } + return 0; +} + +static int tda998x_set_config(struct tda998x_priv *priv, + const struct tda998x_encoder_params *p) +{ + priv->vip_cntrl_0 = VIP_CNTRL_0_SWAP_A(p->swap_a) | + (p->mirr_a ? VIP_CNTRL_0_MIRR_A : 0) | + VIP_CNTRL_0_SWAP_B(p->swap_b) | + (p->mirr_b ? VIP_CNTRL_0_MIRR_B : 0); + priv->vip_cntrl_1 = VIP_CNTRL_1_SWAP_C(p->swap_c) | + (p->mirr_c ? VIP_CNTRL_1_MIRR_C : 0) | + VIP_CNTRL_1_SWAP_D(p->swap_d) | + (p->mirr_d ? VIP_CNTRL_1_MIRR_D : 0); + priv->vip_cntrl_2 = VIP_CNTRL_2_SWAP_E(p->swap_e) | + (p->mirr_e ? VIP_CNTRL_2_MIRR_E : 0) | + VIP_CNTRL_2_SWAP_F(p->swap_f) | + (p->mirr_f ? VIP_CNTRL_2_MIRR_F : 0); + + if (p->audio_params.format != AFMT_UNUSED) { + unsigned int ratio, route; + bool spdif = p->audio_params.format == AFMT_SPDIF; + + route = AUDIO_ROUTE_I2S + spdif; + + priv->audio.route = &tda998x_audio_route[route]; + priv->audio.cea = p->audio_params.cea; + priv->audio.sample_rate = p->audio_params.sample_rate; + memcpy(priv->audio.status, p->audio_params.status, + min(sizeof(priv->audio.status), + sizeof(p->audio_params.status))); + priv->audio.ena_ap = p->audio_params.config; + priv->audio.i2s_format = I2S_FORMAT_PHILIPS; + + ratio = spdif ? 64 : p->audio_params.sample_width * 2; + return tda998x_derive_cts_n(priv, &priv->audio, ratio); + } + + return 0; +} + +static void tda998x_destroy(struct device *dev) +{ + struct tda998x_priv *priv = dev_get_drvdata(dev); + + drm_bridge_remove(&priv->bridge); + + /* disable all IRQs and free the IRQ handler */ + cec_write(priv, REG_CEC_RXSHPDINTENA, 0); + reg_clear(priv, REG_INT_FLAGS_2, INT_FLAGS_2_EDID_BLK_RD); + + if (priv->audio_pdev) + platform_device_unregister(priv->audio_pdev); + + if (priv->hdmi->irq) + free_irq(priv->hdmi->irq, priv); + + del_timer_sync(&priv->edid_delay_timer); + cancel_work_sync(&priv->detect_work); + + i2c_unregister_device(priv->cec); + + cec_notifier_conn_unregister(priv->cec_notify); +} + +static int tda998x_create(struct device *dev) +{ + struct i2c_client *client = to_i2c_client(dev); + struct device_node *np = client->dev.of_node; + struct i2c_board_info cec_info; + struct tda998x_priv *priv; + u32 video; + int rev_lo, rev_hi, ret; + + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + dev_set_drvdata(dev, priv); + + mutex_init(&priv->mutex); /* protect the page access */ + mutex_init(&priv->audio_mutex); /* protect access from audio thread */ + mutex_init(&priv->edid_mutex); + INIT_LIST_HEAD(&priv->bridge.list); + init_waitqueue_head(&priv->edid_delay_waitq); + timer_setup(&priv->edid_delay_timer, tda998x_edid_delay_done, 0); + INIT_WORK(&priv->detect_work, tda998x_detect_work); + + priv->vip_cntrl_0 = VIP_CNTRL_0_SWAP_A(2) | VIP_CNTRL_0_SWAP_B(3); + priv->vip_cntrl_1 = VIP_CNTRL_1_SWAP_C(0) | VIP_CNTRL_1_SWAP_D(1); + priv->vip_cntrl_2 = VIP_CNTRL_2_SWAP_E(4) | VIP_CNTRL_2_SWAP_F(5); + + /* CEC I2C address bound to TDA998x I2C addr by configuration pins */ + priv->cec_addr = 0x34 + (client->addr & 0x03); + priv->current_page = 0xff; + priv->hdmi = client; + + /* wake up the device: */ + cec_write(priv, REG_CEC_ENAMODS, + CEC_ENAMODS_EN_RXSENS | CEC_ENAMODS_EN_HDMI); + + tda998x_reset(priv); + + /* read version: */ + rev_lo = reg_read(priv, REG_VERSION_LSB); + if (rev_lo < 0) { + dev_err(dev, "failed to read version: %d\n", rev_lo); + return rev_lo; + } + + rev_hi = reg_read(priv, REG_VERSION_MSB); + if (rev_hi < 0) { + dev_err(dev, "failed to read version: %d\n", rev_hi); + return rev_hi; + } + + priv->rev = rev_lo | rev_hi << 8; + + /* mask off feature bits: */ + priv->rev &= ~0x30; /* not-hdcp and not-scalar bit */ + + switch (priv->rev) { + case TDA9989N2: + dev_info(dev, "found TDA9989 n2"); + break; + case TDA19989: + dev_info(dev, "found TDA19989"); + break; + case TDA19989N2: + dev_info(dev, "found TDA19989 n2"); + break; + case TDA19988: + dev_info(dev, "found TDA19988"); + break; + default: + dev_err(dev, "found unsupported device: %04x\n", priv->rev); + return -ENXIO; + } + + /* after reset, enable DDC: */ + reg_write(priv, REG_DDC_DISABLE, 0x00); + + /* set clock on DDC channel: */ + reg_write(priv, REG_TX3, 39); + + /* if necessary, disable multi-master: */ + if (priv->rev == TDA19989) + reg_set(priv, REG_I2C_MASTER, I2C_MASTER_DIS_MM); + + cec_write(priv, REG_CEC_FRO_IM_CLK_CTRL, + CEC_FRO_IM_CLK_CTRL_GHOST_DIS | CEC_FRO_IM_CLK_CTRL_IMCLK_SEL); + + /* ensure interrupts are disabled */ + cec_write(priv, REG_CEC_RXSHPDINTENA, 0); + + /* clear pending interrupts */ + cec_read(priv, REG_CEC_RXSHPDINT); + reg_read(priv, REG_INT_FLAGS_0); + reg_read(priv, REG_INT_FLAGS_1); + reg_read(priv, REG_INT_FLAGS_2); + + /* initialize the optional IRQ */ + if (client->irq) { + unsigned long irq_flags; + + /* init read EDID waitqueue and HDP work */ + init_waitqueue_head(&priv->wq_edid); + + irq_flags = + irqd_get_trigger_type(irq_get_irq_data(client->irq)); + + priv->cec_glue.irq_flags = irq_flags; + + irq_flags |= IRQF_SHARED | IRQF_ONESHOT; + ret = request_threaded_irq(client->irq, NULL, + tda998x_irq_thread, irq_flags, + "tda998x", priv); + if (ret) { + dev_err(dev, "failed to request IRQ#%u: %d\n", + client->irq, ret); + goto err_irq; + } + + /* enable HPD irq */ + cec_write(priv, REG_CEC_RXSHPDINTENA, CEC_RXSHPDLEV_HPD); + } + + priv->cec_notify = cec_notifier_conn_register(dev, NULL, NULL); + if (!priv->cec_notify) { + ret = -ENOMEM; + goto fail; + } + + priv->cec_glue.parent = dev; + priv->cec_glue.data = priv; + priv->cec_glue.init = tda998x_cec_hook_init; + priv->cec_glue.exit = tda998x_cec_hook_exit; + priv->cec_glue.open = tda998x_cec_hook_open; + priv->cec_glue.release = tda998x_cec_hook_release; + + /* + * Some TDA998x are actually two I2C devices merged onto one piece + * of silicon: TDA9989 and TDA19989 combine the HDMI transmitter + * with a slightly modified TDA9950 CEC device. The CEC device + * is at the TDA9950 address, with the address pins strapped across + * to the TDA998x address pins. Hence, it always has the same + * offset. + */ + memset(&cec_info, 0, sizeof(cec_info)); + strlcpy(cec_info.type, "tda9950", sizeof(cec_info.type)); + cec_info.addr = priv->cec_addr; + cec_info.platform_data = &priv->cec_glue; + cec_info.irq = client->irq; + + priv->cec = i2c_new_client_device(client->adapter, &cec_info); + if (IS_ERR(priv->cec)) { + ret = PTR_ERR(priv->cec); + goto fail; + } + + /* enable EDID read irq: */ + reg_set(priv, REG_INT_FLAGS_2, INT_FLAGS_2_EDID_BLK_RD); + + if (np) { + /* get the device tree parameters */ + ret = of_property_read_u32(np, "video-ports", &video); + if (ret == 0) { + priv->vip_cntrl_0 = video >> 16; + priv->vip_cntrl_1 = video >> 8; + priv->vip_cntrl_2 = video; + } + + ret = tda998x_get_audio_ports(priv, np); + if (ret) + goto fail; + + if (priv->audio_port_enable[AUDIO_ROUTE_I2S] || + priv->audio_port_enable[AUDIO_ROUTE_SPDIF]) + tda998x_audio_codec_init(priv, &client->dev); + } else if (dev->platform_data) { + ret = tda998x_set_config(priv, dev->platform_data); + if (ret) + goto fail; + } + + priv->bridge.funcs = &tda998x_bridge_funcs; +#ifdef CONFIG_OF + priv->bridge.of_node = dev->of_node; +#endif + + drm_bridge_add(&priv->bridge); + + return 0; + +fail: + tda998x_destroy(dev); +err_irq: + return ret; +} + +/* DRM encoder functions */ + +static int tda998x_encoder_init(struct device *dev, struct drm_device *drm) +{ + struct tda998x_priv *priv = dev_get_drvdata(dev); + u32 crtcs = 0; + int ret; + + if (dev->of_node) + crtcs = drm_of_find_possible_crtcs(drm, dev->of_node); + + /* If no CRTCs were found, fall back to our old behaviour */ + if (crtcs == 0) { + dev_warn(dev, "Falling back to first CRTC\n"); + crtcs = 1 << 0; + } + + priv->encoder.possible_crtcs = crtcs; + + ret = drm_simple_encoder_init(drm, &priv->encoder, + DRM_MODE_ENCODER_TMDS); + if (ret) + goto err_encoder; + + ret = drm_bridge_attach(&priv->encoder, &priv->bridge, NULL, 0); + if (ret) + goto err_bridge; + + return 0; + +err_bridge: + drm_encoder_cleanup(&priv->encoder); +err_encoder: + return ret; +} + +static int tda998x_bind(struct device *dev, struct device *master, void *data) +{ + struct drm_device *drm = data; + + return tda998x_encoder_init(dev, drm); +} + +static void tda998x_unbind(struct device *dev, struct device *master, + void *data) +{ + struct tda998x_priv *priv = dev_get_drvdata(dev); + + drm_encoder_cleanup(&priv->encoder); +} + +static const struct component_ops tda998x_ops = { + .bind = tda998x_bind, + .unbind = tda998x_unbind, +}; + +static int +tda998x_probe(struct i2c_client *client, const struct i2c_device_id *id) +{ + int ret; + + if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) { + dev_warn(&client->dev, "adapter does not support I2C\n"); + return -EIO; + } + + ret = tda998x_create(&client->dev); + if (ret) + return ret; + + ret = component_add(&client->dev, &tda998x_ops); + if (ret) + tda998x_destroy(&client->dev); + return ret; +} + +static void tda998x_remove(struct i2c_client *client) +{ + component_del(&client->dev, &tda998x_ops); + tda998x_destroy(&client->dev); +} + +#ifdef CONFIG_OF +static const struct of_device_id tda998x_dt_ids[] = { + { .compatible = "nxp,tda998x", }, + { } +}; +MODULE_DEVICE_TABLE(of, tda998x_dt_ids); +#endif + +static const struct i2c_device_id tda998x_ids[] = { + { "tda998x", 0 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, tda998x_ids); + +static struct i2c_driver tda998x_driver = { + .probe = tda998x_probe, + .remove = tda998x_remove, + .driver = { + .name = "tda998x", + .of_match_table = of_match_ptr(tda998x_dt_ids), + }, + .id_table = tda998x_ids, +}; + +module_i2c_driver(tda998x_driver); + +MODULE_AUTHOR("Rob Clark <robdclark@gmail.com"); +MODULE_DESCRIPTION("NXP Semiconductors TDA998X HDMI Encoder"); +MODULE_LICENSE("GPL"); |