diff options
Diffstat (limited to 'drivers/net/usb/Kconfig')
| -rw-r--r-- | drivers/net/usb/Kconfig | 648 |
1 files changed, 648 insertions, 0 deletions
diff --git a/drivers/net/usb/Kconfig b/drivers/net/usb/Kconfig new file mode 100644 index 000000000..4402eedb3 --- /dev/null +++ b/drivers/net/usb/Kconfig @@ -0,0 +1,648 @@ +# SPDX-License-Identifier: GPL-2.0-only +# +# USB Network devices configuration +# +comment "Host-side USB support is needed for USB Network Adapter support" + depends on !USB && NET + +menuconfig USB_NET_DRIVERS + tristate "USB Network Adapters" + default USB if USB + depends on USB && NET + +if USB_NET_DRIVERS + +config USB_CATC + tristate "USB CATC NetMate-based Ethernet device support" + select CRC32 + help + Say Y if you want to use one of the following 10Mbps USB Ethernet + device based on the EL1210A chip. Supported devices are: + Belkin F5U011 + Belkin F5U111 + CATC NetMate + CATC NetMate II + smartBridges smartNIC + + This driver makes the adapter appear as a normal Ethernet interface, + typically on eth0, if it is the only ethernet device, or perhaps on + eth1, if you have a PCI or ISA ethernet card installed. + + To compile this driver as a module, choose M here: the + module will be called catc. + +config USB_KAWETH + tristate "USB KLSI KL5USB101-based ethernet device support" + help + Say Y here if you want to use one of the following 10Mbps only + USB Ethernet adapters based on the KLSI KL5KUSB101B chipset: + 3Com 3C19250 + ADS USB-10BT + ATEN USB Ethernet + ASANTE USB To Ethernet Adapter + AOX Endpoints USB Ethernet + Correga K.K. + D-Link DSB-650C and DU-E10 + Entrega / Portgear E45 + I-O DATA USB-ET/T + Jaton USB Ethernet Device Adapter + Kingston Technology USB Ethernet Adapter + Linksys USB10T + Mobility USB-Ethernet Adapter + NetGear EA-101 + Peracom Enet and Enet2 + Portsmith Express Ethernet Adapter + Shark Pocket Adapter + SMC 2202USB + Sony Vaio port extender + + This driver is likely to work with most 10Mbps only USB Ethernet + adapters, including some "no brand" devices. It does NOT work on + SmartBridges smartNIC or on Belkin F5U111 devices - you should use + the CATC NetMate driver for those. If you are not sure which one + you need, select both, and the correct one should be selected for + you. + + This driver makes the adapter appear as a normal Ethernet interface, + typically on eth0, if it is the only ethernet device, or perhaps on + eth1, if you have a PCI or ISA ethernet card installed. + + To compile this driver as a module, choose M here: the + module will be called kaweth. + +config USB_PEGASUS + tristate "USB Pegasus/Pegasus-II based ethernet device support" + select MII + help + Say Y here if you know you have Pegasus or Pegasus-II based adapter. + If in doubt then look at <file:drivers/net/usb/pegasus.h> for the + complete list of supported devices. + + If your particular adapter is not in the list and you are _sure_ it + is Pegasus or Pegasus II based then send me + <petkan@users.sourceforge.net> vendor and device IDs. + + To compile this driver as a module, choose M here: the + module will be called pegasus. + +config USB_RTL8150 + tristate "USB RTL8150 based ethernet device support" + select MII + help + Say Y here if you have RTL8150 based usb-ethernet adapter. + Send me <petkan@users.sourceforge.net> any comments you may have. + You can also check for updates at <http://pegasus2.sourceforge.net/>. + + To compile this driver as a module, choose M here: the + module will be called rtl8150. + +config USB_RTL8152 + tristate "Realtek RTL8152/RTL8153 Based USB Ethernet Adapters" + select MII + select CRC32 + select CRYPTO + select CRYPTO_HASH + select CRYPTO_SHA256 + help + This option adds support for Realtek RTL8152 based USB 2.0 + 10/100 Ethernet adapters and RTL8153 based USB 3.0 10/100/1000 + Ethernet adapters. + + To compile this driver as a module, choose M here: the + module will be called r8152. + +config USB_LAN78XX + tristate "Microchip LAN78XX Based USB Ethernet Adapters" + select MII + select PHYLIB + select MICROCHIP_PHY + select FIXED_PHY + select CRC32 + help + This option adds support for Microchip LAN78XX based USB 2 + & USB 3 10/100/1000 Ethernet adapters. + LAN7800 : USB 3 to 10/100/1000 Ethernet adapter + LAN7850 : USB 2 to 10/100/1000 Ethernet adapter + LAN7801 : USB 3 to 10/100/1000 Ethernet adapter (MAC only) + + Proper PHY driver is required for LAN7801. + + To compile this driver as a module, choose M here: the + module will be called lan78xx. + +config USB_USBNET + tristate "Multi-purpose USB Networking Framework" + select MII + help + This driver supports several kinds of network links over USB, + with "minidrivers" built around a common network driver core + that supports deep queues for efficient transfers. (This gives + better performance with small packets and at high speeds). + + The USB host runs "usbnet", and the other end of the link might be: + + - Another USB host, when using USB "network" or "data transfer" + cables. These are often used to network laptops to PCs, like + "Laplink" parallel cables or some motherboards. These rely + on specialized chips from many suppliers. + + - An intelligent USB gadget, perhaps embedding a Linux system. + These include PDAs running Linux (iPaq, Yopy, Zaurus, and + others), and devices that interoperate using the standard + CDC-Ethernet specification (including many cable modems). + + - Network adapter hardware (like those for 10/100 Ethernet) which + uses this driver framework. + + The link will appear with a name like "usb0", when the link is + a two-node link, or "eth0" for most CDC-Ethernet devices. Those + two-node links are most easily managed with Ethernet Bridging + (CONFIG_BRIDGE) instead of routing. + + For more information see <http://www.linux-usb.org/usbnet/>. + + To compile this driver as a module, choose M here: the + module will be called usbnet. + +config USB_NET_AX8817X + tristate "ASIX AX88xxx Based USB 2.0 Ethernet Adapters" + depends on USB_USBNET + select CRC32 + select PHYLINK + select AX88796B_PHY + imply NET_SELFTESTS + default y + help + This option adds support for ASIX AX88xxx based USB 2.0 + 10/100 Ethernet adapters. + + This driver should work with at least the following devices: + * Aten UC210T + * ASIX AX88172 + * Billionton Systems, USB2AR + * Billionton Systems, GUSB2AM-1G-B + * Buffalo LUA-U2-KTX + * Corega FEther USB2-TX + * D-Link DUB-E100 + * Hawking UF200 + * Linksys USB200M + * Netgear FA120 + * Sitecom LN-029 + * Sitecom LN-028 + * Intellinet USB 2.0 Ethernet + * ST Lab USB 2.0 Ethernet + * TrendNet TU2-ET100 + + This driver creates an interface named "ethX", where X depends on + what other networking devices you have in use. + +config USB_NET_AX88179_178A + tristate "ASIX AX88179/178A USB 3.0/2.0 to Gigabit Ethernet" + depends on USB_USBNET + select CRC32 + select PHYLIB + default y + help + This option adds support for ASIX AX88179 based USB 3.0/2.0 + to Gigabit Ethernet adapters. + + This driver should work with at least the following devices: + * ASIX AX88179 + * ASIX AX88178A + * Sitcomm LN-032 + + This driver creates an interface named "ethX", where X depends on + what other networking devices you have in use. + +config USB_NET_CDCETHER + tristate "CDC Ethernet support (smart devices such as cable modems)" + depends on USB_USBNET + default y + help + This option supports devices conforming to the Communication Device + Class (CDC) Ethernet Control Model, a specification that's easy to + implement in device firmware. The CDC specifications are available + from <http://www.usb.org/>. + + CDC Ethernet is an implementation option for DOCSIS cable modems + that support USB connectivity, used for non-Microsoft USB hosts. + The Linux-USB CDC Ethernet Gadget driver is an open implementation. + This driver should work with at least the following devices: + + * Dell Wireless 5530 HSPA + * Ericsson PipeRider (all variants) + * Ericsson Mobile Broadband Module (all variants) + * Motorola (DM100 and SB4100) + * Broadcom Cable Modem (reference design) + * Toshiba (PCX1100U and F3507g/F3607gw) + * ... + + This driver creates an interface named "ethX", where X depends on + what other networking devices you have in use. However, if the + IEEE 802 "local assignment" bit is set in the address, a "usbX" + name is used instead. + +config USB_NET_CDC_EEM + tristate "CDC EEM support" + depends on USB_USBNET + help + This option supports devices conforming to the Communication Device + Class (CDC) Ethernet Emulation Model, a specification that's easy to + implement in device firmware. The CDC EEM specifications are available + from <http://www.usb.org/>. + + This driver creates an interface named "ethX", where X depends on + what other networking devices you have in use. However, if the + IEEE 802 "local assignment" bit is set in the address, a "usbX" + name is used instead. + +config USB_NET_CDC_NCM + tristate "CDC NCM support" + depends on USB_USBNET + select USB_NET_CDCETHER + default y + help + This driver provides support for CDC NCM (Network Control Model + Device USB Class Specification). The CDC NCM specification is + available from <http://www.usb.org/>. + + Say "y" to link the driver statically, or "m" to build a + dynamically linked module. + + This driver should work with at least the following devices: + * ST-Ericsson M700 LTE FDD/TDD Mobile Broadband Modem (ref. design) + * ST-Ericsson M5730 HSPA+ Mobile Broadband Modem (reference design) + * ST-Ericsson M570 HSPA+ Mobile Broadband Modem (reference design) + * ST-Ericsson M343 HSPA Mobile Broadband Modem (reference design) + * Ericsson F5521gw Mobile Broadband Module + +config USB_NET_HUAWEI_CDC_NCM + tristate "Huawei NCM embedded AT channel support" + depends on USB_USBNET + select USB_WDM + select USB_NET_CDC_NCM + help + This driver supports huawei-style NCM devices, that use NCM as a + transport for other protocols, usually an embedded AT channel. + Good examples are: + * Huawei E3131 + * Huawei E3251 + + To compile this driver as a module, choose M here: the module will be + called huawei_cdc_ncm.ko. + +config USB_NET_CDC_MBIM + tristate "CDC MBIM support" + depends on USB_USBNET + select USB_WDM + select USB_NET_CDC_NCM + help + This driver provides support for CDC MBIM (Mobile Broadband + Interface Model) devices. The CDC MBIM specification is + available from <http://www.usb.org/>. + + MBIM devices require configuration using the management + protocol defined by the MBIM specification. This driver + provides unfiltered access to the MBIM control channel + through the associated /dev/cdc-wdmx character device. + + To compile this driver as a module, choose M here: the + module will be called cdc_mbim. + +config USB_NET_DM9601 + tristate "Davicom DM96xx based USB 10/100 ethernet devices" + depends on USB_USBNET + select CRC32 + help + This option adds support for Davicom DM9601/DM9620/DM9621A + based USB 10/100 Ethernet adapters. + +config USB_NET_SR9700 + tristate "CoreChip-sz SR9700 based USB 1.1 10/100 ethernet devices" + depends on USB_USBNET + select CRC32 + help + This option adds support for CoreChip-sz SR9700 based USB 1.1 + 10/100 Ethernet adapters. + +config USB_NET_SR9800 + tristate "CoreChip-sz SR9800 based USB 2.0 10/100 ethernet devices" + depends on USB_USBNET + select CRC32 + help + Say Y if you want to use one of the following 100Mbps USB Ethernet + device based on the CoreChip-sz SR9800 chip. + + This driver makes the adapter appear as a normal Ethernet interface, + typically on eth0, if it is the only ethernet device, or perhaps on + eth1, if you have a PCI or ISA ethernet card installed. + + To compile this driver as a module, choose M here: the + module will be called sr9800. + +config USB_NET_SMSC75XX + tristate "SMSC LAN75XX based USB 2.0 gigabit ethernet devices" + depends on USB_USBNET + select BITREVERSE + select CRC16 + select CRC32 + help + This option adds support for SMSC LAN75XX based USB 2.0 + Gigabit Ethernet adapters. + +config USB_NET_SMSC95XX + tristate "SMSC LAN95XX based USB 2.0 10/100 ethernet devices" + depends on USB_USBNET + select PHYLIB + select SMSC_PHY + select BITREVERSE + select CRC16 + select CRC32 + imply NET_SELFTESTS + help + This option adds support for SMSC LAN95XX based USB 2.0 + 10/100 Ethernet adapters. + +config USB_NET_GL620A + tristate "GeneSys GL620USB-A based cables" + depends on USB_USBNET + help + Choose this option if you're using a host-to-host cable, + or PC2PC motherboard, with this chip. + + Note that the half-duplex "GL620USB" is not supported. + +config USB_NET_NET1080 + tristate "NetChip 1080 based cables (Laplink, ...)" + default y + depends on USB_USBNET + help + Choose this option if you're using a host-to-host cable based + on this design: one NetChip 1080 chip and supporting logic, + optionally with LEDs that indicate traffic + +config USB_NET_PLUSB + tristate "Prolific PL-2301/2302/25A1/27A1 based cables" + # if the handshake/init/reset problems, from original 'plusb', + # are ever resolved ... then remove "experimental" + depends on USB_USBNET + help + Choose this option if you're using a host-to-host cable + with one of these chips. + +config USB_NET_MCS7830 + tristate "MosChip MCS7830 based Ethernet adapters" + depends on USB_USBNET + help + Choose this option if you're using a 10/100 Ethernet USB2 + adapter based on the MosChip 7830 controller. This includes + adapters marketed under the DeLOCK brand. + +config USB_NET_RNDIS_HOST + tristate "Host for RNDIS and ActiveSync devices" + depends on USB_USBNET + select USB_NET_CDCETHER + help + This option enables hosting "Remote NDIS" USB networking links, + as encouraged by Microsoft (instead of CDC Ethernet!) for use in + various devices that may only support this protocol. A variant + of this protocol (with even less public documentation) seems to + be at the root of Microsoft's "ActiveSync" too. + + Avoid using this protocol unless you have no better options. + The protocol specification is incomplete, and is controlled by + (and for) Microsoft; it isn't an "Open" ecosystem or market. + +config USB_NET_CDC_SUBSET_ENABLE + tristate + depends on USB_NET_CDC_SUBSET + +config USB_NET_CDC_SUBSET + tristate "Simple USB Network Links (CDC Ethernet subset)" + depends on USB_USBNET + default y + help + This driver module supports USB network devices that can work + without any device-specific information. Select it if you have + one of these drivers. + + Note that while many USB host-to-host cables can work in this mode, + that may mean not being able to talk to Win32 systems or more + commonly not being able to handle certain events (like replugging + the host on the other end) very well. Also, these devices will + not generally have permanently assigned Ethernet addresses. + +config USB_ALI_M5632 + bool "ALi M5632 based 'USB 2.0 Data Link' cables" + depends on USB_NET_CDC_SUBSET + select USB_NET_CDC_SUBSET_ENABLE + help + Choose this option if you're using a host-to-host cable + based on this design, which supports USB 2.0 high speed. + +config USB_AN2720 + bool "AnchorChips 2720 based cables (Xircom PGUNET, ...)" + depends on USB_NET_CDC_SUBSET + select USB_NET_CDC_SUBSET_ENABLE + help + Choose this option if you're using a host-to-host cable + based on this design. Note that AnchorChips is now a + Cypress brand. + +config USB_BELKIN + bool "eTEK based host-to-host cables (Advance, Belkin, ...)" + depends on USB_NET_CDC_SUBSET + select USB_NET_CDC_SUBSET_ENABLE + default y + help + Choose this option if you're using a host-to-host cable + based on this design: two NetChip 2890 chips and an Atmel + microcontroller, with LEDs that indicate traffic. + +config USB_ARMLINUX + bool "Embedded ARM Linux links (iPaq, ...)" + depends on USB_NET_CDC_SUBSET + select USB_NET_CDC_SUBSET_ENABLE + default y + help + Choose this option to support the "usb-eth" networking driver + used by most of the ARM Linux community with device controllers + such as the SA-11x0 and PXA-25x UDCs, or the tftp capabilities + in some PXA versions of the "blob" boot loader. + + Linux-based "Gumstix" PXA-25x based systems use this protocol + to talk with other Linux systems. + + Although the ROMs shipped with Sharp Zaurus products use a + different link level framing protocol, you can have them use + this simpler protocol by installing a different kernel. + +config USB_EPSON2888 + bool "Epson 2888 based firmware (DEVELOPMENT)" + depends on USB_NET_CDC_SUBSET + select USB_NET_CDC_SUBSET_ENABLE + help + Choose this option to support the usb networking links used + by some sample firmware from Epson. + +config USB_KC2190 + bool "KT Technology KC2190 based cables (InstaNet)" + depends on USB_NET_CDC_SUBSET + select USB_NET_CDC_SUBSET_ENABLE + help + Choose this option if you're using a host-to-host cable + with one of these chips. + +config USB_NET_ZAURUS + tristate "Sharp Zaurus (stock ROMs) and compatible" + depends on USB_USBNET + select USB_NET_CDCETHER + select CRC32 + default y + help + Choose this option to support the usb networking links used by + Zaurus models like the SL-5000D, SL-5500, SL-5600, A-300, B-500. + This also supports some related device firmware, as used in some + PDAs from Olympus and some cell phones from Motorola. + + If you install an alternate image, such as the Linux 2.6 based + versions of OpenZaurus, you should no longer need to support this + protocol. Only the "eth-fd" or "net_fd" drivers in these devices + really need this non-conformant variant of CDC Ethernet (or in + some cases CDC MDLM) protocol, not "g_ether". + +config USB_NET_CX82310_ETH + tristate "Conexant CX82310 USB ethernet port" + depends on USB_USBNET + help + Choose this option if you're using a Conexant CX82310-based ADSL + router with USB ethernet port. This driver is for routers only, + it will not work with ADSL modems (use cxacru driver instead). + +config USB_NET_KALMIA + tristate "Samsung Kalmia based LTE USB modem" + depends on USB_USBNET + help + Choose this option if you have a Samsung Kalmia based USB modem + as Samsung GT-B3730. + + To compile this driver as a module, choose M here: the + module will be called kalmia. + +config USB_NET_QMI_WWAN + tristate "QMI WWAN driver for Qualcomm MSM based 3G and LTE modems" + depends on USB_USBNET + select USB_WDM + help + Support WWAN LTE/3G devices based on Qualcomm Mobile Data Modem + (MDM) chipsets. Examples of such devices are + * Huawei E392/E398 + + This driver will only drive the ethernet part of the chips. + The devices require additional configuration to be usable. + Multiple management interfaces with linux drivers are + available: + + * option: AT commands on /dev/ttyUSBx + * cdc-wdm: Qualcomm MSM Interface (QMI) protocol on /dev/cdc-wdmx + + A modem manager with support for QMI is recommended. + + To compile this driver as a module, choose M here: the + module will be called qmi_wwan. + +config USB_HSO + tristate "Option USB High Speed Mobile Devices" + depends on USB && RFKILL && TTY + default n + help + Choose this option if you have an Option HSDPA/HSUPA card. + These cards support downlink speeds of 7.2Mbps or greater. + + To compile this driver as a module, choose M here: the + module will be called hso. + +config USB_NET_INT51X1 + tristate "Intellon PLC based usb adapter" + depends on USB_USBNET + help + Choose this option if you're using a 14Mb USB-based PLC + (Powerline Communications) solution with an Intellon + INT51x1/INT5200 chip, like the "devolo dLan duo". + +config USB_CDC_PHONET + tristate "CDC Phonet support" + depends on PHONET && USB_USBNET + help + Choose this option to support the Phonet interface to a Nokia + cellular modem, as found on most Nokia handsets with the + "PC suite" USB profile. + +config USB_IPHETH + tristate "Apple iPhone USB Ethernet driver" + default n + help + Module used to share Internet connection (tethering) from your + iPhone (Original, 3G and 3GS) to your system. + Note that you need userspace libraries and programs that are needed + to pair your device with your system and that understand the iPhone + protocol. + + For more information: http://giagio.com/wiki/moin.cgi/iPhoneEthernetDriver + +config USB_SIERRA_NET + tristate "USB-to-WWAN Driver for Sierra Wireless modems" + depends on USB_USBNET + help + Choose this option if you have a Sierra Wireless USB-to-WWAN device. + + To compile this driver as a module, choose M here: the + module will be called sierra_net. + +config USB_VL600 + tristate "LG VL600 modem dongle" + depends on USB_NET_CDCETHER && TTY + select USB_ACM + help + Select this if you want to use an LG Electronics 4G/LTE usb modem + called VL600. This driver only handles the ethernet + interface exposed by the modem firmware. To establish a connection + you will first need a userspace program that sends the right + command to the modem through its CDC ACM port, and most + likely also a DHCP client. See this thread about using the + 4G modem from Verizon: + + http://ubuntuforums.org/showpost.php?p=10589647&postcount=17 + +config USB_NET_CH9200 + tristate "QingHeng CH9200 USB ethernet support" + depends on USB_USBNET + select MII + help + Choose this option if you have a USB ethernet adapter with a QinHeng + CH9200 chipset. + + To compile this driver as a module, choose M here: the + module will be called ch9200. + +config USB_NET_AQC111 + tristate "Aquantia AQtion USB to 5/2.5GbE Controllers support" + depends on USB_USBNET + select CRC32 + help + This option adds support for Aquantia AQtion USB + Ethernet adapters based on AQC111U/AQC112 chips. + + This driver should work with at least the following devices: + * Aquantia AQtion USB to 5GbE + +config USB_RTL8153_ECM + tristate + depends on USB_NET_CDCETHER && (USB_RTL8152 || USB_RTL8152=n) + default y + help + This option supports ECM mode for RTL8153 ethernet adapter, when + CONFIG_USB_RTL8152 is not set, or the RTL8153 device is not + supported by r8152 driver. + +endif # USB_NET_DRIVERS |