diff options
Diffstat (limited to 'drivers/net/wireless/ralink/rt2x00/rt2500usb.c')
-rw-r--r-- | drivers/net/wireless/ralink/rt2x00/rt2500usb.c | 1979 |
1 files changed, 1979 insertions, 0 deletions
diff --git a/drivers/net/wireless/ralink/rt2x00/rt2500usb.c b/drivers/net/wireless/ralink/rt2x00/rt2500usb.c new file mode 100644 index 000000000..4f3b0e6c6 --- /dev/null +++ b/drivers/net/wireless/ralink/rt2x00/rt2500usb.c @@ -0,0 +1,1979 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + Copyright (C) 2004 - 2009 Ivo van Doorn <IvDoorn@gmail.com> + <http://rt2x00.serialmonkey.com> + + */ + +/* + Module: rt2500usb + Abstract: rt2500usb device specific routines. + Supported chipsets: RT2570. + */ + +#include <linux/delay.h> +#include <linux/etherdevice.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/slab.h> +#include <linux/usb.h> + +#include "rt2x00.h" +#include "rt2x00usb.h" +#include "rt2500usb.h" + +/* + * Allow hardware encryption to be disabled. + */ +static bool modparam_nohwcrypt; +module_param_named(nohwcrypt, modparam_nohwcrypt, bool, 0444); +MODULE_PARM_DESC(nohwcrypt, "Disable hardware encryption."); + +/* + * Register access. + * All access to the CSR registers will go through the methods + * rt2500usb_register_read and rt2500usb_register_write. + * BBP and RF register require indirect register access, + * and use the CSR registers BBPCSR and RFCSR to achieve this. + * These indirect registers work with busy bits, + * and we will try maximal REGISTER_USB_BUSY_COUNT times to access + * the register while taking a REGISTER_BUSY_DELAY us delay + * between each attampt. When the busy bit is still set at that time, + * the access attempt is considered to have failed, + * and we will print an error. + * If the csr_mutex is already held then the _lock variants must + * be used instead. + */ +static u16 rt2500usb_register_read(struct rt2x00_dev *rt2x00dev, + const unsigned int offset) +{ + __le16 reg; + rt2x00usb_vendor_request_buff(rt2x00dev, USB_MULTI_READ, + USB_VENDOR_REQUEST_IN, offset, + ®, sizeof(reg)); + return le16_to_cpu(reg); +} + +static u16 rt2500usb_register_read_lock(struct rt2x00_dev *rt2x00dev, + const unsigned int offset) +{ + __le16 reg; + rt2x00usb_vendor_req_buff_lock(rt2x00dev, USB_MULTI_READ, + USB_VENDOR_REQUEST_IN, offset, + ®, sizeof(reg), REGISTER_TIMEOUT); + return le16_to_cpu(reg); +} + +static void rt2500usb_register_write(struct rt2x00_dev *rt2x00dev, + const unsigned int offset, + u16 value) +{ + __le16 reg = cpu_to_le16(value); + rt2x00usb_vendor_request_buff(rt2x00dev, USB_MULTI_WRITE, + USB_VENDOR_REQUEST_OUT, offset, + ®, sizeof(reg)); +} + +static void rt2500usb_register_write_lock(struct rt2x00_dev *rt2x00dev, + const unsigned int offset, + u16 value) +{ + __le16 reg = cpu_to_le16(value); + rt2x00usb_vendor_req_buff_lock(rt2x00dev, USB_MULTI_WRITE, + USB_VENDOR_REQUEST_OUT, offset, + ®, sizeof(reg), REGISTER_TIMEOUT); +} + +static void rt2500usb_register_multiwrite(struct rt2x00_dev *rt2x00dev, + const unsigned int offset, + void *value, const u16 length) +{ + rt2x00usb_vendor_request_buff(rt2x00dev, USB_MULTI_WRITE, + USB_VENDOR_REQUEST_OUT, offset, + value, length); +} + +static int rt2500usb_regbusy_read(struct rt2x00_dev *rt2x00dev, + const unsigned int offset, + struct rt2x00_field16 field, + u16 *reg) +{ + unsigned int i; + + for (i = 0; i < REGISTER_USB_BUSY_COUNT; i++) { + *reg = rt2500usb_register_read_lock(rt2x00dev, offset); + if (!rt2x00_get_field16(*reg, field)) + return 1; + udelay(REGISTER_BUSY_DELAY); + } + + rt2x00_err(rt2x00dev, "Indirect register access failed: offset=0x%.08x, value=0x%.08x\n", + offset, *reg); + *reg = ~0; + + return 0; +} + +#define WAIT_FOR_BBP(__dev, __reg) \ + rt2500usb_regbusy_read((__dev), PHY_CSR8, PHY_CSR8_BUSY, (__reg)) +#define WAIT_FOR_RF(__dev, __reg) \ + rt2500usb_regbusy_read((__dev), PHY_CSR10, PHY_CSR10_RF_BUSY, (__reg)) + +static void rt2500usb_bbp_write(struct rt2x00_dev *rt2x00dev, + const unsigned int word, const u8 value) +{ + u16 reg; + + mutex_lock(&rt2x00dev->csr_mutex); + + /* + * Wait until the BBP becomes available, afterwards we + * can safely write the new data into the register. + */ + if (WAIT_FOR_BBP(rt2x00dev, ®)) { + reg = 0; + rt2x00_set_field16(®, PHY_CSR7_DATA, value); + rt2x00_set_field16(®, PHY_CSR7_REG_ID, word); + rt2x00_set_field16(®, PHY_CSR7_READ_CONTROL, 0); + + rt2500usb_register_write_lock(rt2x00dev, PHY_CSR7, reg); + } + + mutex_unlock(&rt2x00dev->csr_mutex); +} + +static u8 rt2500usb_bbp_read(struct rt2x00_dev *rt2x00dev, + const unsigned int word) +{ + u16 reg; + u8 value; + + mutex_lock(&rt2x00dev->csr_mutex); + + /* + * Wait until the BBP becomes available, afterwards we + * can safely write the read request into the register. + * After the data has been written, we wait until hardware + * returns the correct value, if at any time the register + * doesn't become available in time, reg will be 0xffffffff + * which means we return 0xff to the caller. + */ + if (WAIT_FOR_BBP(rt2x00dev, ®)) { + reg = 0; + rt2x00_set_field16(®, PHY_CSR7_REG_ID, word); + rt2x00_set_field16(®, PHY_CSR7_READ_CONTROL, 1); + + rt2500usb_register_write_lock(rt2x00dev, PHY_CSR7, reg); + + if (WAIT_FOR_BBP(rt2x00dev, ®)) + reg = rt2500usb_register_read_lock(rt2x00dev, PHY_CSR7); + } + + value = rt2x00_get_field16(reg, PHY_CSR7_DATA); + + mutex_unlock(&rt2x00dev->csr_mutex); + + return value; +} + +static void rt2500usb_rf_write(struct rt2x00_dev *rt2x00dev, + const unsigned int word, const u32 value) +{ + u16 reg; + + mutex_lock(&rt2x00dev->csr_mutex); + + /* + * Wait until the RF becomes available, afterwards we + * can safely write the new data into the register. + */ + if (WAIT_FOR_RF(rt2x00dev, ®)) { + reg = 0; + rt2x00_set_field16(®, PHY_CSR9_RF_VALUE, value); + rt2500usb_register_write_lock(rt2x00dev, PHY_CSR9, reg); + + reg = 0; + rt2x00_set_field16(®, PHY_CSR10_RF_VALUE, value >> 16); + rt2x00_set_field16(®, PHY_CSR10_RF_NUMBER_OF_BITS, 20); + rt2x00_set_field16(®, PHY_CSR10_RF_IF_SELECT, 0); + rt2x00_set_field16(®, PHY_CSR10_RF_BUSY, 1); + + rt2500usb_register_write_lock(rt2x00dev, PHY_CSR10, reg); + rt2x00_rf_write(rt2x00dev, word, value); + } + + mutex_unlock(&rt2x00dev->csr_mutex); +} + +#ifdef CONFIG_RT2X00_LIB_DEBUGFS +static u32 _rt2500usb_register_read(struct rt2x00_dev *rt2x00dev, + const unsigned int offset) +{ + return rt2500usb_register_read(rt2x00dev, offset); +} + +static void _rt2500usb_register_write(struct rt2x00_dev *rt2x00dev, + const unsigned int offset, + u32 value) +{ + rt2500usb_register_write(rt2x00dev, offset, value); +} + +static const struct rt2x00debug rt2500usb_rt2x00debug = { + .owner = THIS_MODULE, + .csr = { + .read = _rt2500usb_register_read, + .write = _rt2500usb_register_write, + .flags = RT2X00DEBUGFS_OFFSET, + .word_base = CSR_REG_BASE, + .word_size = sizeof(u16), + .word_count = CSR_REG_SIZE / sizeof(u16), + }, + .eeprom = { + .read = rt2x00_eeprom_read, + .write = rt2x00_eeprom_write, + .word_base = EEPROM_BASE, + .word_size = sizeof(u16), + .word_count = EEPROM_SIZE / sizeof(u16), + }, + .bbp = { + .read = rt2500usb_bbp_read, + .write = rt2500usb_bbp_write, + .word_base = BBP_BASE, + .word_size = sizeof(u8), + .word_count = BBP_SIZE / sizeof(u8), + }, + .rf = { + .read = rt2x00_rf_read, + .write = rt2500usb_rf_write, + .word_base = RF_BASE, + .word_size = sizeof(u32), + .word_count = RF_SIZE / sizeof(u32), + }, +}; +#endif /* CONFIG_RT2X00_LIB_DEBUGFS */ + +static int rt2500usb_rfkill_poll(struct rt2x00_dev *rt2x00dev) +{ + u16 reg; + + reg = rt2500usb_register_read(rt2x00dev, MAC_CSR19); + return rt2x00_get_field16(reg, MAC_CSR19_VAL7); +} + +#ifdef CONFIG_RT2X00_LIB_LEDS +static void rt2500usb_brightness_set(struct led_classdev *led_cdev, + enum led_brightness brightness) +{ + struct rt2x00_led *led = + container_of(led_cdev, struct rt2x00_led, led_dev); + unsigned int enabled = brightness != LED_OFF; + u16 reg; + + reg = rt2500usb_register_read(led->rt2x00dev, MAC_CSR20); + + if (led->type == LED_TYPE_RADIO || led->type == LED_TYPE_ASSOC) + rt2x00_set_field16(®, MAC_CSR20_LINK, enabled); + else if (led->type == LED_TYPE_ACTIVITY) + rt2x00_set_field16(®, MAC_CSR20_ACTIVITY, enabled); + + rt2500usb_register_write(led->rt2x00dev, MAC_CSR20, reg); +} + +static int rt2500usb_blink_set(struct led_classdev *led_cdev, + unsigned long *delay_on, + unsigned long *delay_off) +{ + struct rt2x00_led *led = + container_of(led_cdev, struct rt2x00_led, led_dev); + u16 reg; + + reg = rt2500usb_register_read(led->rt2x00dev, MAC_CSR21); + rt2x00_set_field16(®, MAC_CSR21_ON_PERIOD, *delay_on); + rt2x00_set_field16(®, MAC_CSR21_OFF_PERIOD, *delay_off); + rt2500usb_register_write(led->rt2x00dev, MAC_CSR21, reg); + + return 0; +} + +static void rt2500usb_init_led(struct rt2x00_dev *rt2x00dev, + struct rt2x00_led *led, + enum led_type type) +{ + led->rt2x00dev = rt2x00dev; + led->type = type; + led->led_dev.brightness_set = rt2500usb_brightness_set; + led->led_dev.blink_set = rt2500usb_blink_set; + led->flags = LED_INITIALIZED; +} +#endif /* CONFIG_RT2X00_LIB_LEDS */ + +/* + * Configuration handlers. + */ + +/* + * rt2500usb does not differentiate between shared and pairwise + * keys, so we should use the same function for both key types. + */ +static int rt2500usb_config_key(struct rt2x00_dev *rt2x00dev, + struct rt2x00lib_crypto *crypto, + struct ieee80211_key_conf *key) +{ + u32 mask; + u16 reg; + enum cipher curr_cipher; + + if (crypto->cmd == SET_KEY) { + /* + * Disallow to set WEP key other than with index 0, + * it is known that not work at least on some hardware. + * SW crypto will be used in that case. + */ + if ((key->cipher == WLAN_CIPHER_SUITE_WEP40 || + key->cipher == WLAN_CIPHER_SUITE_WEP104) && + key->keyidx != 0) + return -EOPNOTSUPP; + + /* + * Pairwise key will always be entry 0, but this + * could collide with a shared key on the same + * position... + */ + mask = TXRX_CSR0_KEY_ID.bit_mask; + + reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR0); + curr_cipher = rt2x00_get_field16(reg, TXRX_CSR0_ALGORITHM); + reg &= mask; + + if (reg && reg == mask) + return -ENOSPC; + + reg = rt2x00_get_field16(reg, TXRX_CSR0_KEY_ID); + + key->hw_key_idx += reg ? ffz(reg) : 0; + /* + * Hardware requires that all keys use the same cipher + * (e.g. TKIP-only, AES-only, but not TKIP+AES). + * If this is not the first key, compare the cipher with the + * first one and fall back to SW crypto if not the same. + */ + if (key->hw_key_idx > 0 && crypto->cipher != curr_cipher) + return -EOPNOTSUPP; + + rt2500usb_register_multiwrite(rt2x00dev, KEY_ENTRY(key->hw_key_idx), + crypto->key, sizeof(crypto->key)); + + /* + * The driver does not support the IV/EIV generation + * in hardware. However it demands the data to be provided + * both separately as well as inside the frame. + * We already provided the CONFIG_CRYPTO_COPY_IV to rt2x00lib + * to ensure rt2x00lib will not strip the data from the + * frame after the copy, now we must tell mac80211 + * to generate the IV/EIV data. + */ + key->flags |= IEEE80211_KEY_FLAG_GENERATE_IV; + key->flags |= IEEE80211_KEY_FLAG_GENERATE_MMIC; + } + + /* + * TXRX_CSR0_KEY_ID contains only single-bit fields to indicate + * a particular key is valid. + */ + reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR0); + rt2x00_set_field16(®, TXRX_CSR0_ALGORITHM, crypto->cipher); + rt2x00_set_field16(®, TXRX_CSR0_IV_OFFSET, IEEE80211_HEADER); + + mask = rt2x00_get_field16(reg, TXRX_CSR0_KEY_ID); + if (crypto->cmd == SET_KEY) + mask |= 1 << key->hw_key_idx; + else if (crypto->cmd == DISABLE_KEY) + mask &= ~(1 << key->hw_key_idx); + rt2x00_set_field16(®, TXRX_CSR0_KEY_ID, mask); + rt2500usb_register_write(rt2x00dev, TXRX_CSR0, reg); + + return 0; +} + +static void rt2500usb_config_filter(struct rt2x00_dev *rt2x00dev, + const unsigned int filter_flags) +{ + u16 reg; + + /* + * Start configuration steps. + * Note that the version error will always be dropped + * and broadcast frames will always be accepted since + * there is no filter for it at this time. + */ + reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR2); + rt2x00_set_field16(®, TXRX_CSR2_DROP_CRC, + !(filter_flags & FIF_FCSFAIL)); + rt2x00_set_field16(®, TXRX_CSR2_DROP_PHYSICAL, + !(filter_flags & FIF_PLCPFAIL)); + rt2x00_set_field16(®, TXRX_CSR2_DROP_CONTROL, + !(filter_flags & FIF_CONTROL)); + rt2x00_set_field16(®, TXRX_CSR2_DROP_NOT_TO_ME, + !test_bit(CONFIG_MONITORING, &rt2x00dev->flags)); + rt2x00_set_field16(®, TXRX_CSR2_DROP_TODS, + !test_bit(CONFIG_MONITORING, &rt2x00dev->flags) && + !rt2x00dev->intf_ap_count); + rt2x00_set_field16(®, TXRX_CSR2_DROP_VERSION_ERROR, 1); + rt2x00_set_field16(®, TXRX_CSR2_DROP_MULTICAST, + !(filter_flags & FIF_ALLMULTI)); + rt2x00_set_field16(®, TXRX_CSR2_DROP_BROADCAST, 0); + rt2500usb_register_write(rt2x00dev, TXRX_CSR2, reg); +} + +static void rt2500usb_config_intf(struct rt2x00_dev *rt2x00dev, + struct rt2x00_intf *intf, + struct rt2x00intf_conf *conf, + const unsigned int flags) +{ + unsigned int bcn_preload; + u16 reg; + + if (flags & CONFIG_UPDATE_TYPE) { + /* + * Enable beacon config + */ + bcn_preload = PREAMBLE + GET_DURATION(IEEE80211_HEADER, 20); + reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR20); + rt2x00_set_field16(®, TXRX_CSR20_OFFSET, bcn_preload >> 6); + rt2x00_set_field16(®, TXRX_CSR20_BCN_EXPECT_WINDOW, + 2 * (conf->type != NL80211_IFTYPE_STATION)); + rt2500usb_register_write(rt2x00dev, TXRX_CSR20, reg); + + /* + * Enable synchronisation. + */ + reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR18); + rt2x00_set_field16(®, TXRX_CSR18_OFFSET, 0); + rt2500usb_register_write(rt2x00dev, TXRX_CSR18, reg); + + reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR19); + rt2x00_set_field16(®, TXRX_CSR19_TSF_SYNC, conf->sync); + rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg); + } + + if (flags & CONFIG_UPDATE_MAC) + rt2500usb_register_multiwrite(rt2x00dev, MAC_CSR2, conf->mac, + (3 * sizeof(__le16))); + + if (flags & CONFIG_UPDATE_BSSID) + rt2500usb_register_multiwrite(rt2x00dev, MAC_CSR5, conf->bssid, + (3 * sizeof(__le16))); +} + +static void rt2500usb_config_erp(struct rt2x00_dev *rt2x00dev, + struct rt2x00lib_erp *erp, + u32 changed) +{ + u16 reg; + + if (changed & BSS_CHANGED_ERP_PREAMBLE) { + reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR10); + rt2x00_set_field16(®, TXRX_CSR10_AUTORESPOND_PREAMBLE, + !!erp->short_preamble); + rt2500usb_register_write(rt2x00dev, TXRX_CSR10, reg); + } + + if (changed & BSS_CHANGED_BASIC_RATES) + rt2500usb_register_write(rt2x00dev, TXRX_CSR11, + erp->basic_rates); + + if (changed & BSS_CHANGED_BEACON_INT) { + reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR18); + rt2x00_set_field16(®, TXRX_CSR18_INTERVAL, + erp->beacon_int * 4); + rt2500usb_register_write(rt2x00dev, TXRX_CSR18, reg); + } + + if (changed & BSS_CHANGED_ERP_SLOT) { + rt2500usb_register_write(rt2x00dev, MAC_CSR10, erp->slot_time); + rt2500usb_register_write(rt2x00dev, MAC_CSR11, erp->sifs); + rt2500usb_register_write(rt2x00dev, MAC_CSR12, erp->eifs); + } +} + +static void rt2500usb_config_ant(struct rt2x00_dev *rt2x00dev, + struct antenna_setup *ant) +{ + u8 r2; + u8 r14; + u16 csr5; + u16 csr6; + + /* + * We should never come here because rt2x00lib is supposed + * to catch this and send us the correct antenna explicitely. + */ + BUG_ON(ant->rx == ANTENNA_SW_DIVERSITY || + ant->tx == ANTENNA_SW_DIVERSITY); + + r2 = rt2500usb_bbp_read(rt2x00dev, 2); + r14 = rt2500usb_bbp_read(rt2x00dev, 14); + csr5 = rt2500usb_register_read(rt2x00dev, PHY_CSR5); + csr6 = rt2500usb_register_read(rt2x00dev, PHY_CSR6); + + /* + * Configure the TX antenna. + */ + switch (ant->tx) { + case ANTENNA_HW_DIVERSITY: + rt2x00_set_field8(&r2, BBP_R2_TX_ANTENNA, 1); + rt2x00_set_field16(&csr5, PHY_CSR5_CCK, 1); + rt2x00_set_field16(&csr6, PHY_CSR6_OFDM, 1); + break; + case ANTENNA_A: + rt2x00_set_field8(&r2, BBP_R2_TX_ANTENNA, 0); + rt2x00_set_field16(&csr5, PHY_CSR5_CCK, 0); + rt2x00_set_field16(&csr6, PHY_CSR6_OFDM, 0); + break; + case ANTENNA_B: + default: + rt2x00_set_field8(&r2, BBP_R2_TX_ANTENNA, 2); + rt2x00_set_field16(&csr5, PHY_CSR5_CCK, 2); + rt2x00_set_field16(&csr6, PHY_CSR6_OFDM, 2); + break; + } + + /* + * Configure the RX antenna. + */ + switch (ant->rx) { + case ANTENNA_HW_DIVERSITY: + rt2x00_set_field8(&r14, BBP_R14_RX_ANTENNA, 1); + break; + case ANTENNA_A: + rt2x00_set_field8(&r14, BBP_R14_RX_ANTENNA, 0); + break; + case ANTENNA_B: + default: + rt2x00_set_field8(&r14, BBP_R14_RX_ANTENNA, 2); + break; + } + + /* + * RT2525E and RT5222 need to flip TX I/Q + */ + if (rt2x00_rf(rt2x00dev, RF2525E) || rt2x00_rf(rt2x00dev, RF5222)) { + rt2x00_set_field8(&r2, BBP_R2_TX_IQ_FLIP, 1); + rt2x00_set_field16(&csr5, PHY_CSR5_CCK_FLIP, 1); + rt2x00_set_field16(&csr6, PHY_CSR6_OFDM_FLIP, 1); + + /* + * RT2525E does not need RX I/Q Flip. + */ + if (rt2x00_rf(rt2x00dev, RF2525E)) + rt2x00_set_field8(&r14, BBP_R14_RX_IQ_FLIP, 0); + } else { + rt2x00_set_field16(&csr5, PHY_CSR5_CCK_FLIP, 0); + rt2x00_set_field16(&csr6, PHY_CSR6_OFDM_FLIP, 0); + } + + rt2500usb_bbp_write(rt2x00dev, 2, r2); + rt2500usb_bbp_write(rt2x00dev, 14, r14); + rt2500usb_register_write(rt2x00dev, PHY_CSR5, csr5); + rt2500usb_register_write(rt2x00dev, PHY_CSR6, csr6); +} + +static void rt2500usb_config_channel(struct rt2x00_dev *rt2x00dev, + struct rf_channel *rf, const int txpower) +{ + /* + * Set TXpower. + */ + rt2x00_set_field32(&rf->rf3, RF3_TXPOWER, TXPOWER_TO_DEV(txpower)); + + /* + * For RT2525E we should first set the channel to half band higher. + */ + if (rt2x00_rf(rt2x00dev, RF2525E)) { + static const u32 vals[] = { + 0x000008aa, 0x000008ae, 0x000008ae, 0x000008b2, + 0x000008b2, 0x000008b6, 0x000008b6, 0x000008ba, + 0x000008ba, 0x000008be, 0x000008b7, 0x00000902, + 0x00000902, 0x00000906 + }; + + rt2500usb_rf_write(rt2x00dev, 2, vals[rf->channel - 1]); + if (rf->rf4) + rt2500usb_rf_write(rt2x00dev, 4, rf->rf4); + } + + rt2500usb_rf_write(rt2x00dev, 1, rf->rf1); + rt2500usb_rf_write(rt2x00dev, 2, rf->rf2); + rt2500usb_rf_write(rt2x00dev, 3, rf->rf3); + if (rf->rf4) + rt2500usb_rf_write(rt2x00dev, 4, rf->rf4); +} + +static void rt2500usb_config_txpower(struct rt2x00_dev *rt2x00dev, + const int txpower) +{ + u32 rf3; + + rf3 = rt2x00_rf_read(rt2x00dev, 3); + rt2x00_set_field32(&rf3, RF3_TXPOWER, TXPOWER_TO_DEV(txpower)); + rt2500usb_rf_write(rt2x00dev, 3, rf3); +} + +static void rt2500usb_config_ps(struct rt2x00_dev *rt2x00dev, + struct rt2x00lib_conf *libconf) +{ + enum dev_state state = + (libconf->conf->flags & IEEE80211_CONF_PS) ? + STATE_SLEEP : STATE_AWAKE; + u16 reg; + + if (state == STATE_SLEEP) { + reg = rt2500usb_register_read(rt2x00dev, MAC_CSR18); + rt2x00_set_field16(®, MAC_CSR18_DELAY_AFTER_BEACON, + rt2x00dev->beacon_int - 20); + rt2x00_set_field16(®, MAC_CSR18_BEACONS_BEFORE_WAKEUP, + libconf->conf->listen_interval - 1); + + /* We must first disable autowake before it can be enabled */ + rt2x00_set_field16(®, MAC_CSR18_AUTO_WAKE, 0); + rt2500usb_register_write(rt2x00dev, MAC_CSR18, reg); + + rt2x00_set_field16(®, MAC_CSR18_AUTO_WAKE, 1); + rt2500usb_register_write(rt2x00dev, MAC_CSR18, reg); + } else { + reg = rt2500usb_register_read(rt2x00dev, MAC_CSR18); + rt2x00_set_field16(®, MAC_CSR18_AUTO_WAKE, 0); + rt2500usb_register_write(rt2x00dev, MAC_CSR18, reg); + } + + rt2x00dev->ops->lib->set_device_state(rt2x00dev, state); +} + +static void rt2500usb_config(struct rt2x00_dev *rt2x00dev, + struct rt2x00lib_conf *libconf, + const unsigned int flags) +{ + if (flags & IEEE80211_CONF_CHANGE_CHANNEL) + rt2500usb_config_channel(rt2x00dev, &libconf->rf, + libconf->conf->power_level); + if ((flags & IEEE80211_CONF_CHANGE_POWER) && + !(flags & IEEE80211_CONF_CHANGE_CHANNEL)) + rt2500usb_config_txpower(rt2x00dev, + libconf->conf->power_level); + if (flags & IEEE80211_CONF_CHANGE_PS) + rt2500usb_config_ps(rt2x00dev, libconf); +} + +/* + * Link tuning + */ +static void rt2500usb_link_stats(struct rt2x00_dev *rt2x00dev, + struct link_qual *qual) +{ + u16 reg; + + /* + * Update FCS error count from register. + */ + reg = rt2500usb_register_read(rt2x00dev, STA_CSR0); + qual->rx_failed = rt2x00_get_field16(reg, STA_CSR0_FCS_ERROR); + + /* + * Update False CCA count from register. + */ + reg = rt2500usb_register_read(rt2x00dev, STA_CSR3); + qual->false_cca = rt2x00_get_field16(reg, STA_CSR3_FALSE_CCA_ERROR); +} + +static void rt2500usb_reset_tuner(struct rt2x00_dev *rt2x00dev, + struct link_qual *qual) +{ + u16 eeprom; + u16 value; + + eeprom = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_R24); + value = rt2x00_get_field16(eeprom, EEPROM_BBPTUNE_R24_LOW); + rt2500usb_bbp_write(rt2x00dev, 24, value); + + eeprom = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_R25); + value = rt2x00_get_field16(eeprom, EEPROM_BBPTUNE_R25_LOW); + rt2500usb_bbp_write(rt2x00dev, 25, value); + + eeprom = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_R61); + value = rt2x00_get_field16(eeprom, EEPROM_BBPTUNE_R61_LOW); + rt2500usb_bbp_write(rt2x00dev, 61, value); + + eeprom = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_VGC); + value = rt2x00_get_field16(eeprom, EEPROM_BBPTUNE_VGCUPPER); + rt2500usb_bbp_write(rt2x00dev, 17, value); + + qual->vgc_level = value; +} + +/* + * Queue handlers. + */ +static void rt2500usb_start_queue(struct data_queue *queue) +{ + struct rt2x00_dev *rt2x00dev = queue->rt2x00dev; + u16 reg; + + switch (queue->qid) { + case QID_RX: + reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR2); + rt2x00_set_field16(®, TXRX_CSR2_DISABLE_RX, 0); + rt2500usb_register_write(rt2x00dev, TXRX_CSR2, reg); + break; + case QID_BEACON: + reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR19); + rt2x00_set_field16(®, TXRX_CSR19_TSF_COUNT, 1); + rt2x00_set_field16(®, TXRX_CSR19_TBCN, 1); + rt2x00_set_field16(®, TXRX_CSR19_BEACON_GEN, 1); + rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg); + break; + default: + break; + } +} + +static void rt2500usb_stop_queue(struct data_queue *queue) +{ + struct rt2x00_dev *rt2x00dev = queue->rt2x00dev; + u16 reg; + + switch (queue->qid) { + case QID_RX: + reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR2); + rt2x00_set_field16(®, TXRX_CSR2_DISABLE_RX, 1); + rt2500usb_register_write(rt2x00dev, TXRX_CSR2, reg); + break; + case QID_BEACON: + reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR19); + rt2x00_set_field16(®, TXRX_CSR19_TSF_COUNT, 0); + rt2x00_set_field16(®, TXRX_CSR19_TBCN, 0); + rt2x00_set_field16(®, TXRX_CSR19_BEACON_GEN, 0); + rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg); + break; + default: + break; + } +} + +/* + * Initialization functions. + */ +static int rt2500usb_init_registers(struct rt2x00_dev *rt2x00dev) +{ + u16 reg; + + rt2x00usb_vendor_request_sw(rt2x00dev, USB_DEVICE_MODE, 0x0001, + USB_MODE_TEST, REGISTER_TIMEOUT); + rt2x00usb_vendor_request_sw(rt2x00dev, USB_SINGLE_WRITE, 0x0308, + 0x00f0, REGISTER_TIMEOUT); + + reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR2); + rt2x00_set_field16(®, TXRX_CSR2_DISABLE_RX, 1); + rt2500usb_register_write(rt2x00dev, TXRX_CSR2, reg); + + rt2500usb_register_write(rt2x00dev, MAC_CSR13, 0x1111); + rt2500usb_register_write(rt2x00dev, MAC_CSR14, 0x1e11); + + reg = rt2500usb_register_read(rt2x00dev, MAC_CSR1); + rt2x00_set_field16(®, MAC_CSR1_SOFT_RESET, 1); + rt2x00_set_field16(®, MAC_CSR1_BBP_RESET, 1); + rt2x00_set_field16(®, MAC_CSR1_HOST_READY, 0); + rt2500usb_register_write(rt2x00dev, MAC_CSR1, reg); + + reg = rt2500usb_register_read(rt2x00dev, MAC_CSR1); + rt2x00_set_field16(®, MAC_CSR1_SOFT_RESET, 0); + rt2x00_set_field16(®, MAC_CSR1_BBP_RESET, 0); + rt2x00_set_field16(®, MAC_CSR1_HOST_READY, 0); + rt2500usb_register_write(rt2x00dev, MAC_CSR1, reg); + + reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR5); + rt2x00_set_field16(®, TXRX_CSR5_BBP_ID0, 13); + rt2x00_set_field16(®, TXRX_CSR5_BBP_ID0_VALID, 1); + rt2x00_set_field16(®, TXRX_CSR5_BBP_ID1, 12); + rt2x00_set_field16(®, TXRX_CSR5_BBP_ID1_VALID, 1); + rt2500usb_register_write(rt2x00dev, TXRX_CSR5, reg); + + reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR6); + rt2x00_set_field16(®, TXRX_CSR6_BBP_ID0, 10); + rt2x00_set_field16(®, TXRX_CSR6_BBP_ID0_VALID, 1); + rt2x00_set_field16(®, TXRX_CSR6_BBP_ID1, 11); + rt2x00_set_field16(®, TXRX_CSR6_BBP_ID1_VALID, 1); + rt2500usb_register_write(rt2x00dev, TXRX_CSR6, reg); + + reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR7); + rt2x00_set_field16(®, TXRX_CSR7_BBP_ID0, 7); + rt2x00_set_field16(®, TXRX_CSR7_BBP_ID0_VALID, 1); + rt2x00_set_field16(®, TXRX_CSR7_BBP_ID1, 6); + rt2x00_set_field16(®, TXRX_CSR7_BBP_ID1_VALID, 1); + rt2500usb_register_write(rt2x00dev, TXRX_CSR7, reg); + + reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR8); + rt2x00_set_field16(®, TXRX_CSR8_BBP_ID0, 5); + rt2x00_set_field16(®, TXRX_CSR8_BBP_ID0_VALID, 1); + rt2x00_set_field16(®, TXRX_CSR8_BBP_ID1, 0); + rt2x00_set_field16(®, TXRX_CSR8_BBP_ID1_VALID, 0); + rt2500usb_register_write(rt2x00dev, TXRX_CSR8, reg); + + reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR19); + rt2x00_set_field16(®, TXRX_CSR19_TSF_COUNT, 0); + rt2x00_set_field16(®, TXRX_CSR19_TSF_SYNC, 0); + rt2x00_set_field16(®, TXRX_CSR19_TBCN, 0); + rt2x00_set_field16(®, TXRX_CSR19_BEACON_GEN, 0); + rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg); + + rt2500usb_register_write(rt2x00dev, TXRX_CSR21, 0xe78f); + rt2500usb_register_write(rt2x00dev, MAC_CSR9, 0xff1d); + + if (rt2x00dev->ops->lib->set_device_state(rt2x00dev, STATE_AWAKE)) + return -EBUSY; + + reg = rt2500usb_register_read(rt2x00dev, MAC_CSR1); + rt2x00_set_field16(®, MAC_CSR1_SOFT_RESET, 0); + rt2x00_set_field16(®, MAC_CSR1_BBP_RESET, 0); + rt2x00_set_field16(®, MAC_CSR1_HOST_READY, 1); + rt2500usb_register_write(rt2x00dev, MAC_CSR1, reg); + + if (rt2x00_rev(rt2x00dev) >= RT2570_VERSION_C) { + reg = rt2500usb_register_read(rt2x00dev, PHY_CSR2); + rt2x00_set_field16(®, PHY_CSR2_LNA, 0); + } else { + reg = 0; + rt2x00_set_field16(®, PHY_CSR2_LNA, 1); + rt2x00_set_field16(®, PHY_CSR2_LNA_MODE, 3); + } + rt2500usb_register_write(rt2x00dev, PHY_CSR2, reg); + + rt2500usb_register_write(rt2x00dev, MAC_CSR11, 0x0002); + rt2500usb_register_write(rt2x00dev, MAC_CSR22, 0x0053); + rt2500usb_register_write(rt2x00dev, MAC_CSR15, 0x01ee); + rt2500usb_register_write(rt2x00dev, MAC_CSR16, 0x0000); + + reg = rt2500usb_register_read(rt2x00dev, MAC_CSR8); + rt2x00_set_field16(®, MAC_CSR8_MAX_FRAME_UNIT, + rt2x00dev->rx->data_size); + rt2500usb_register_write(rt2x00dev, MAC_CSR8, reg); + + reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR0); + rt2x00_set_field16(®, TXRX_CSR0_ALGORITHM, CIPHER_NONE); + rt2x00_set_field16(®, TXRX_CSR0_IV_OFFSET, IEEE80211_HEADER); + rt2x00_set_field16(®, TXRX_CSR0_KEY_ID, 0); + rt2500usb_register_write(rt2x00dev, TXRX_CSR0, reg); + + reg = rt2500usb_register_read(rt2x00dev, MAC_CSR18); + rt2x00_set_field16(®, MAC_CSR18_DELAY_AFTER_BEACON, 90); + rt2500usb_register_write(rt2x00dev, MAC_CSR18, reg); + + reg = rt2500usb_register_read(rt2x00dev, PHY_CSR4); + rt2x00_set_field16(®, PHY_CSR4_LOW_RF_LE, 1); + rt2500usb_register_write(rt2x00dev, PHY_CSR4, reg); + + reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR1); + rt2x00_set_field16(®, TXRX_CSR1_AUTO_SEQUENCE, 1); + rt2500usb_register_write(rt2x00dev, TXRX_CSR1, reg); + + return 0; +} + +static int rt2500usb_wait_bbp_ready(struct rt2x00_dev *rt2x00dev) +{ + unsigned int i; + u8 value; + + for (i = 0; i < REGISTER_USB_BUSY_COUNT; i++) { + value = rt2500usb_bbp_read(rt2x00dev, 0); + if ((value != 0xff) && (value != 0x00)) + return 0; + udelay(REGISTER_BUSY_DELAY); + } + + rt2x00_err(rt2x00dev, "BBP register access failed, aborting\n"); + return -EACCES; +} + +static int rt2500usb_init_bbp(struct rt2x00_dev *rt2x00dev) +{ + unsigned int i; + u16 eeprom; + u8 value; + u8 reg_id; + + if (unlikely(rt2500usb_wait_bbp_ready(rt2x00dev))) + return -EACCES; + + rt2500usb_bbp_write(rt2x00dev, 3, 0x02); + rt2500usb_bbp_write(rt2x00dev, 4, 0x19); + rt2500usb_bbp_write(rt2x00dev, 14, 0x1c); + rt2500usb_bbp_write(rt2x00dev, 15, 0x30); + rt2500usb_bbp_write(rt2x00dev, 16, 0xac); + rt2500usb_bbp_write(rt2x00dev, 18, 0x18); + rt2500usb_bbp_write(rt2x00dev, 19, 0xff); + rt2500usb_bbp_write(rt2x00dev, 20, 0x1e); + rt2500usb_bbp_write(rt2x00dev, 21, 0x08); + rt2500usb_bbp_write(rt2x00dev, 22, 0x08); + rt2500usb_bbp_write(rt2x00dev, 23, 0x08); + rt2500usb_bbp_write(rt2x00dev, 24, 0x80); + rt2500usb_bbp_write(rt2x00dev, 25, 0x50); + rt2500usb_bbp_write(rt2x00dev, 26, 0x08); + rt2500usb_bbp_write(rt2x00dev, 27, 0x23); + rt2500usb_bbp_write(rt2x00dev, 30, 0x10); + rt2500usb_bbp_write(rt2x00dev, 31, 0x2b); + rt2500usb_bbp_write(rt2x00dev, 32, 0xb9); + rt2500usb_bbp_write(rt2x00dev, 34, 0x12); + rt2500usb_bbp_write(rt2x00dev, 35, 0x50); + rt2500usb_bbp_write(rt2x00dev, 39, 0xc4); + rt2500usb_bbp_write(rt2x00dev, 40, 0x02); + rt2500usb_bbp_write(rt2x00dev, 41, 0x60); + rt2500usb_bbp_write(rt2x00dev, 53, 0x10); + rt2500usb_bbp_write(rt2x00dev, 54, 0x18); + rt2500usb_bbp_write(rt2x00dev, 56, 0x08); + rt2500usb_bbp_write(rt2x00dev, 57, 0x10); + rt2500usb_bbp_write(rt2x00dev, 58, 0x08); + rt2500usb_bbp_write(rt2x00dev, 61, 0x60); + rt2500usb_bbp_write(rt2x00dev, 62, 0x10); + rt2500usb_bbp_write(rt2x00dev, 75, 0xff); + + for (i = 0; i < EEPROM_BBP_SIZE; i++) { + eeprom = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBP_START + i); + + if (eeprom != 0xffff && eeprom != 0x0000) { + reg_id = rt2x00_get_field16(eeprom, EEPROM_BBP_REG_ID); + value = rt2x00_get_field16(eeprom, EEPROM_BBP_VALUE); + rt2500usb_bbp_write(rt2x00dev, reg_id, value); + } + } + + return 0; +} + +/* + * Device state switch handlers. + */ +static int rt2500usb_enable_radio(struct rt2x00_dev *rt2x00dev) +{ + /* + * Initialize all registers. + */ + if (unlikely(rt2500usb_init_registers(rt2x00dev) || + rt2500usb_init_bbp(rt2x00dev))) + return -EIO; + + return 0; +} + +static void rt2500usb_disable_radio(struct rt2x00_dev *rt2x00dev) +{ + rt2500usb_register_write(rt2x00dev, MAC_CSR13, 0x2121); + rt2500usb_register_write(rt2x00dev, MAC_CSR14, 0x2121); + + /* + * Disable synchronisation. + */ + rt2500usb_register_write(rt2x00dev, TXRX_CSR19, 0); + + rt2x00usb_disable_radio(rt2x00dev); +} + +static int rt2500usb_set_state(struct rt2x00_dev *rt2x00dev, + enum dev_state state) +{ + u16 reg; + u16 reg2; + unsigned int i; + bool put_to_sleep; + u8 bbp_state; + u8 rf_state; + + put_to_sleep = (state != STATE_AWAKE); + + reg = 0; + rt2x00_set_field16(®, MAC_CSR17_BBP_DESIRE_STATE, state); + rt2x00_set_field16(®, MAC_CSR17_RF_DESIRE_STATE, state); + rt2x00_set_field16(®, MAC_CSR17_PUT_TO_SLEEP, put_to_sleep); + rt2500usb_register_write(rt2x00dev, MAC_CSR17, reg); + rt2x00_set_field16(®, MAC_CSR17_SET_STATE, 1); + rt2500usb_register_write(rt2x00dev, MAC_CSR17, reg); + + /* + * Device is not guaranteed to be in the requested state yet. + * We must wait until the register indicates that the + * device has entered the correct state. + */ + for (i = 0; i < REGISTER_USB_BUSY_COUNT; i++) { + reg2 = rt2500usb_register_read(rt2x00dev, MAC_CSR17); + bbp_state = rt2x00_get_field16(reg2, MAC_CSR17_BBP_CURR_STATE); + rf_state = rt2x00_get_field16(reg2, MAC_CSR17_RF_CURR_STATE); + if (bbp_state == state && rf_state == state) + return 0; + rt2500usb_register_write(rt2x00dev, MAC_CSR17, reg); + msleep(30); + } + + return -EBUSY; +} + +static int rt2500usb_set_device_state(struct rt2x00_dev *rt2x00dev, + enum dev_state state) +{ + int retval = 0; + + switch (state) { + case STATE_RADIO_ON: + retval = rt2500usb_enable_radio(rt2x00dev); + break; + case STATE_RADIO_OFF: + rt2500usb_disable_radio(rt2x00dev); + break; + case STATE_RADIO_IRQ_ON: + case STATE_RADIO_IRQ_OFF: + /* No support, but no error either */ + break; + case STATE_DEEP_SLEEP: + case STATE_SLEEP: + case STATE_STANDBY: + case STATE_AWAKE: + retval = rt2500usb_set_state(rt2x00dev, state); + break; + default: + retval = -ENOTSUPP; + break; + } + + if (unlikely(retval)) + rt2x00_err(rt2x00dev, "Device failed to enter state %d (%d)\n", + state, retval); + + return retval; +} + +/* + * TX descriptor initialization + */ +static void rt2500usb_write_tx_desc(struct queue_entry *entry, + struct txentry_desc *txdesc) +{ + struct skb_frame_desc *skbdesc = get_skb_frame_desc(entry->skb); + __le32 *txd = (__le32 *) entry->skb->data; + u32 word; + + /* + * Start writing the descriptor words. + */ + word = rt2x00_desc_read(txd, 0); + rt2x00_set_field32(&word, TXD_W0_RETRY_LIMIT, txdesc->retry_limit); + rt2x00_set_field32(&word, TXD_W0_MORE_FRAG, + test_bit(ENTRY_TXD_MORE_FRAG, &txdesc->flags)); + rt2x00_set_field32(&word, TXD_W0_ACK, + test_bit(ENTRY_TXD_ACK, &txdesc->flags)); + rt2x00_set_field32(&word, TXD_W0_TIMESTAMP, + test_bit(ENTRY_TXD_REQ_TIMESTAMP, &txdesc->flags)); + rt2x00_set_field32(&word, TXD_W0_OFDM, + (txdesc->rate_mode == RATE_MODE_OFDM)); + rt2x00_set_field32(&word, TXD_W0_NEW_SEQ, + test_bit(ENTRY_TXD_FIRST_FRAGMENT, &txdesc->flags)); + rt2x00_set_field32(&word, TXD_W0_IFS, txdesc->u.plcp.ifs); + rt2x00_set_field32(&word, TXD_W0_DATABYTE_COUNT, txdesc->length); + rt2x00_set_field32(&word, TXD_W0_CIPHER, !!txdesc->cipher); + rt2x00_set_field32(&word, TXD_W0_KEY_ID, txdesc->key_idx); + rt2x00_desc_write(txd, 0, word); + + word = rt2x00_desc_read(txd, 1); + rt2x00_set_field32(&word, TXD_W1_IV_OFFSET, txdesc->iv_offset); + rt2x00_set_field32(&word, TXD_W1_AIFS, entry->queue->aifs); + rt2x00_set_field32(&word, TXD_W1_CWMIN, entry->queue->cw_min); + rt2x00_set_field32(&word, TXD_W1_CWMAX, entry->queue->cw_max); + rt2x00_desc_write(txd, 1, word); + + word = rt2x00_desc_read(txd, 2); + rt2x00_set_field32(&word, TXD_W2_PLCP_SIGNAL, txdesc->u.plcp.signal); + rt2x00_set_field32(&word, TXD_W2_PLCP_SERVICE, txdesc->u.plcp.service); + rt2x00_set_field32(&word, TXD_W2_PLCP_LENGTH_LOW, + txdesc->u.plcp.length_low); + rt2x00_set_field32(&word, TXD_W2_PLCP_LENGTH_HIGH, + txdesc->u.plcp.length_high); + rt2x00_desc_write(txd, 2, word); + + if (test_bit(ENTRY_TXD_ENCRYPT, &txdesc->flags)) { + _rt2x00_desc_write(txd, 3, skbdesc->iv[0]); + _rt2x00_desc_write(txd, 4, skbdesc->iv[1]); + } + + /* + * Register descriptor details in skb frame descriptor. + */ + skbdesc->flags |= SKBDESC_DESC_IN_SKB; + skbdesc->desc = txd; + skbdesc->desc_len = TXD_DESC_SIZE; +} + +/* + * TX data initialization + */ +static void rt2500usb_beacondone(struct urb *urb); + +static void rt2500usb_write_beacon(struct queue_entry *entry, + struct txentry_desc *txdesc) +{ + struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev; + struct usb_device *usb_dev = to_usb_device_intf(rt2x00dev->dev); + struct queue_entry_priv_usb_bcn *bcn_priv = entry->priv_data; + int pipe = usb_sndbulkpipe(usb_dev, entry->queue->usb_endpoint); + int length; + u16 reg, reg0; + + /* + * Disable beaconing while we are reloading the beacon data, + * otherwise we might be sending out invalid data. + */ + reg = rt2500usb_register_read(rt2x00dev, TXRX_CSR19); + rt2x00_set_field16(®, TXRX_CSR19_BEACON_GEN, 0); + rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg); + + /* + * Add space for the descriptor in front of the skb. + */ + skb_push(entry->skb, TXD_DESC_SIZE); + memset(entry->skb->data, 0, TXD_DESC_SIZE); + + /* + * Write the TX descriptor for the beacon. + */ + rt2500usb_write_tx_desc(entry, txdesc); + + /* + * Dump beacon to userspace through debugfs. + */ + rt2x00debug_dump_frame(rt2x00dev, DUMP_FRAME_BEACON, entry); + + /* + * USB devices cannot blindly pass the skb->len as the + * length of the data to usb_fill_bulk_urb. Pass the skb + * to the driver to determine what the length should be. + */ + length = rt2x00dev->ops->lib->get_tx_data_len(entry); + + usb_fill_bulk_urb(bcn_priv->urb, usb_dev, pipe, + entry->skb->data, length, rt2500usb_beacondone, + entry); + + /* + * Second we need to create the guardian byte. + * We only need a single byte, so lets recycle + * the 'flags' field we are not using for beacons. + */ + bcn_priv->guardian_data = 0; + usb_fill_bulk_urb(bcn_priv->guardian_urb, usb_dev, pipe, + &bcn_priv->guardian_data, 1, rt2500usb_beacondone, + entry); + + /* + * Send out the guardian byte. + */ + usb_submit_urb(bcn_priv->guardian_urb, GFP_ATOMIC); + + /* + * Enable beaconing again. + */ + rt2x00_set_field16(®, TXRX_CSR19_TSF_COUNT, 1); + rt2x00_set_field16(®, TXRX_CSR19_TBCN, 1); + reg0 = reg; + rt2x00_set_field16(®, TXRX_CSR19_BEACON_GEN, 1); + /* + * Beacon generation will fail initially. + * To prevent this we need to change the TXRX_CSR19 + * register several times (reg0 is the same as reg + * except for TXRX_CSR19_BEACON_GEN, which is 0 in reg0 + * and 1 in reg). + */ + rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg); + rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg0); + rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg); + rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg0); + rt2500usb_register_write(rt2x00dev, TXRX_CSR19, reg); +} + +static int rt2500usb_get_tx_data_len(struct queue_entry *entry) +{ + int length; + + /* + * The length _must_ be a multiple of 2, + * but it must _not_ be a multiple of the USB packet size. + */ + length = roundup(entry->skb->len, 2); + length += (2 * !(length % entry->queue->usb_maxpacket)); + + return length; +} + +/* + * RX control handlers + */ +static void rt2500usb_fill_rxdone(struct queue_entry *entry, + struct rxdone_entry_desc *rxdesc) +{ + struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev; + struct queue_entry_priv_usb *entry_priv = entry->priv_data; + struct skb_frame_desc *skbdesc = get_skb_frame_desc(entry->skb); + __le32 *rxd = + (__le32 *)(entry->skb->data + + (entry_priv->urb->actual_length - + entry->queue->desc_size)); + u32 word0; + u32 word1; + + /* + * Copy descriptor to the skbdesc->desc buffer, making it safe from moving of + * frame data in rt2x00usb. + */ + memcpy(skbdesc->desc, rxd, skbdesc->desc_len); + rxd = (__le32 *)skbdesc->desc; + + /* + * It is now safe to read the descriptor on all architectures. + */ + word0 = rt2x00_desc_read(rxd, 0); + word1 = rt2x00_desc_read(rxd, 1); + + if (rt2x00_get_field32(word0, RXD_W0_CRC_ERROR)) + rxdesc->flags |= RX_FLAG_FAILED_FCS_CRC; + if (rt2x00_get_field32(word0, RXD_W0_PHYSICAL_ERROR)) + rxdesc->flags |= RX_FLAG_FAILED_PLCP_CRC; + + rxdesc->cipher = rt2x00_get_field32(word0, RXD_W0_CIPHER); + if (rt2x00_get_field32(word0, RXD_W0_CIPHER_ERROR)) + rxdesc->cipher_status = RX_CRYPTO_FAIL_KEY; + + if (rxdesc->cipher != CIPHER_NONE) { + rxdesc->iv[0] = _rt2x00_desc_read(rxd, 2); + rxdesc->iv[1] = _rt2x00_desc_read(rxd, 3); + rxdesc->dev_flags |= RXDONE_CRYPTO_IV; + + /* ICV is located at the end of frame */ + + rxdesc->flags |= RX_FLAG_MMIC_STRIPPED; + if (rxdesc->cipher_status == RX_CRYPTO_SUCCESS) + rxdesc->flags |= RX_FLAG_DECRYPTED; + else if (rxdesc->cipher_status == RX_CRYPTO_FAIL_MIC) + rxdesc->flags |= RX_FLAG_MMIC_ERROR; + } + + /* + * Obtain the status about this packet. + * When frame was received with an OFDM bitrate, + * the signal is the PLCP value. If it was received with + * a CCK bitrate the signal is the rate in 100kbit/s. + */ + rxdesc->signal = rt2x00_get_field32(word1, RXD_W1_SIGNAL); + rxdesc->rssi = + rt2x00_get_field32(word1, RXD_W1_RSSI) - rt2x00dev->rssi_offset; + rxdesc->size = rt2x00_get_field32(word0, RXD_W0_DATABYTE_COUNT); + + if (rt2x00_get_field32(word0, RXD_W0_OFDM)) + rxdesc->dev_flags |= RXDONE_SIGNAL_PLCP; + else + rxdesc->dev_flags |= RXDONE_SIGNAL_BITRATE; + if (rt2x00_get_field32(word0, RXD_W0_MY_BSS)) + rxdesc->dev_flags |= RXDONE_MY_BSS; + + /* + * Adjust the skb memory window to the frame boundaries. + */ + skb_trim(entry->skb, rxdesc->size); +} + +/* + * Interrupt functions. + */ +static void rt2500usb_beacondone(struct urb *urb) +{ + struct queue_entry *entry = (struct queue_entry *)urb->context; + struct queue_entry_priv_usb_bcn *bcn_priv = entry->priv_data; + + if (!test_bit(DEVICE_STATE_ENABLED_RADIO, &entry->queue->rt2x00dev->flags)) + return; + + /* + * Check if this was the guardian beacon, + * if that was the case we need to send the real beacon now. + * Otherwise we should free the sk_buffer, the device + * should be doing the rest of the work now. + */ + if (bcn_priv->guardian_urb == urb) { + usb_submit_urb(bcn_priv->urb, GFP_ATOMIC); + } else if (bcn_priv->urb == urb) { + dev_kfree_skb(entry->skb); + entry->skb = NULL; + } +} + +/* + * Device probe functions. + */ +static int rt2500usb_validate_eeprom(struct rt2x00_dev *rt2x00dev) +{ + u16 word; + u8 *mac; + u8 bbp; + + rt2x00usb_eeprom_read(rt2x00dev, rt2x00dev->eeprom, EEPROM_SIZE); + + /* + * Start validation of the data that has been read. + */ + mac = rt2x00_eeprom_addr(rt2x00dev, EEPROM_MAC_ADDR_0); + rt2x00lib_set_mac_address(rt2x00dev, mac); + + word = rt2x00_eeprom_read(rt2x00dev, EEPROM_ANTENNA); + if (word == 0xffff) { + rt2x00_set_field16(&word, EEPROM_ANTENNA_NUM, 2); + rt2x00_set_field16(&word, EEPROM_ANTENNA_TX_DEFAULT, + ANTENNA_SW_DIVERSITY); + rt2x00_set_field16(&word, EEPROM_ANTENNA_RX_DEFAULT, + ANTENNA_SW_DIVERSITY); + rt2x00_set_field16(&word, EEPROM_ANTENNA_LED_MODE, + LED_MODE_DEFAULT); + rt2x00_set_field16(&word, EEPROM_ANTENNA_DYN_TXAGC, 0); + rt2x00_set_field16(&word, EEPROM_ANTENNA_HARDWARE_RADIO, 0); + rt2x00_set_field16(&word, EEPROM_ANTENNA_RF_TYPE, RF2522); + rt2x00_eeprom_write(rt2x00dev, EEPROM_ANTENNA, word); + rt2x00_eeprom_dbg(rt2x00dev, "Antenna: 0x%04x\n", word); + } + + word = rt2x00_eeprom_read(rt2x00dev, EEPROM_NIC); + if (word == 0xffff) { + rt2x00_set_field16(&word, EEPROM_NIC_CARDBUS_ACCEL, 0); + rt2x00_set_field16(&word, EEPROM_NIC_DYN_BBP_TUNE, 0); + rt2x00_set_field16(&word, EEPROM_NIC_CCK_TX_POWER, 0); + rt2x00_eeprom_write(rt2x00dev, EEPROM_NIC, word); + rt2x00_eeprom_dbg(rt2x00dev, "NIC: 0x%04x\n", word); + } + + word = rt2x00_eeprom_read(rt2x00dev, EEPROM_CALIBRATE_OFFSET); + if (word == 0xffff) { + rt2x00_set_field16(&word, EEPROM_CALIBRATE_OFFSET_RSSI, + DEFAULT_RSSI_OFFSET); + rt2x00_eeprom_write(rt2x00dev, EEPROM_CALIBRATE_OFFSET, word); + rt2x00_eeprom_dbg(rt2x00dev, "Calibrate offset: 0x%04x\n", + word); + } + + word = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE); + if (word == 0xffff) { + rt2x00_set_field16(&word, EEPROM_BBPTUNE_THRESHOLD, 45); + rt2x00_eeprom_write(rt2x00dev, EEPROM_BBPTUNE, word); + rt2x00_eeprom_dbg(rt2x00dev, "BBPtune: 0x%04x\n", word); + } + + /* + * Switch lower vgc bound to current BBP R17 value, + * lower the value a bit for better quality. + */ + bbp = rt2500usb_bbp_read(rt2x00dev, 17); + bbp -= 6; + + word = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_VGC); + if (word == 0xffff) { + rt2x00_set_field16(&word, EEPROM_BBPTUNE_VGCUPPER, 0x40); + rt2x00_set_field16(&word, EEPROM_BBPTUNE_VGCLOWER, bbp); + rt2x00_eeprom_write(rt2x00dev, EEPROM_BBPTUNE_VGC, word); + rt2x00_eeprom_dbg(rt2x00dev, "BBPtune vgc: 0x%04x\n", word); + } else { + rt2x00_set_field16(&word, EEPROM_BBPTUNE_VGCLOWER, bbp); + rt2x00_eeprom_write(rt2x00dev, EEPROM_BBPTUNE_VGC, word); + } + + word = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_R17); + if (word == 0xffff) { + rt2x00_set_field16(&word, EEPROM_BBPTUNE_R17_LOW, 0x48); + rt2x00_set_field16(&word, EEPROM_BBPTUNE_R17_HIGH, 0x41); + rt2x00_eeprom_write(rt2x00dev, EEPROM_BBPTUNE_R17, word); + rt2x00_eeprom_dbg(rt2x00dev, "BBPtune r17: 0x%04x\n", word); + } + + word = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_R24); + if (word == 0xffff) { + rt2x00_set_field16(&word, EEPROM_BBPTUNE_R24_LOW, 0x40); + rt2x00_set_field16(&word, EEPROM_BBPTUNE_R24_HIGH, 0x80); + rt2x00_eeprom_write(rt2x00dev, EEPROM_BBPTUNE_R24, word); + rt2x00_eeprom_dbg(rt2x00dev, "BBPtune r24: 0x%04x\n", word); + } + + word = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_R25); + if (word == 0xffff) { + rt2x00_set_field16(&word, EEPROM_BBPTUNE_R25_LOW, 0x40); + rt2x00_set_field16(&word, EEPROM_BBPTUNE_R25_HIGH, 0x50); + rt2x00_eeprom_write(rt2x00dev, EEPROM_BBPTUNE_R25, word); + rt2x00_eeprom_dbg(rt2x00dev, "BBPtune r25: 0x%04x\n", word); + } + + word = rt2x00_eeprom_read(rt2x00dev, EEPROM_BBPTUNE_R61); + if (word == 0xffff) { + rt2x00_set_field16(&word, EEPROM_BBPTUNE_R61_LOW, 0x60); + rt2x00_set_field16(&word, EEPROM_BBPTUNE_R61_HIGH, 0x6d); + rt2x00_eeprom_write(rt2x00dev, EEPROM_BBPTUNE_R61, word); + rt2x00_eeprom_dbg(rt2x00dev, "BBPtune r61: 0x%04x\n", word); + } + + return 0; +} + +static int rt2500usb_init_eeprom(struct rt2x00_dev *rt2x00dev) +{ + u16 reg; + u16 value; + u16 eeprom; + + /* + * Read EEPROM word for configuration. + */ + eeprom = rt2x00_eeprom_read(rt2x00dev, EEPROM_ANTENNA); + + /* + * Identify RF chipset. + */ + value = rt2x00_get_field16(eeprom, EEPROM_ANTENNA_RF_TYPE); + reg = rt2500usb_register_read(rt2x00dev, MAC_CSR0); + rt2x00_set_chip(rt2x00dev, RT2570, value, reg); + + if (((reg & 0xfff0) != 0) || ((reg & 0x0000000f) == 0)) { + rt2x00_err(rt2x00dev, "Invalid RT chipset detected\n"); + return -ENODEV; + } + + if (!rt2x00_rf(rt2x00dev, RF2522) && + !rt2x00_rf(rt2x00dev, RF2523) && + !rt2x00_rf(rt2x00dev, RF2524) && + !rt2x00_rf(rt2x00dev, RF2525) && + !rt2x00_rf(rt2x00dev, RF2525E) && + !rt2x00_rf(rt2x00dev, RF5222)) { + rt2x00_err(rt2x00dev, "Invalid RF chipset detected\n"); + return -ENODEV; + } + + /* + * Identify default antenna configuration. + */ + rt2x00dev->default_ant.tx = + rt2x00_get_field16(eeprom, EEPROM_ANTENNA_TX_DEFAULT); + rt2x00dev->default_ant.rx = + rt2x00_get_field16(eeprom, EEPROM_ANTENNA_RX_DEFAULT); + + /* + * When the eeprom indicates SW_DIVERSITY use HW_DIVERSITY instead. + * I am not 100% sure about this, but the legacy drivers do not + * indicate antenna swapping in software is required when + * diversity is enabled. + */ + if (rt2x00dev->default_ant.tx == ANTENNA_SW_DIVERSITY) + rt2x00dev->default_ant.tx = ANTENNA_HW_DIVERSITY; + if (rt2x00dev->default_ant.rx == ANTENNA_SW_DIVERSITY) + rt2x00dev->default_ant.rx = ANTENNA_HW_DIVERSITY; + + /* + * Store led mode, for correct led behaviour. + */ +#ifdef CONFIG_RT2X00_LIB_LEDS + value = rt2x00_get_field16(eeprom, EEPROM_ANTENNA_LED_MODE); + + rt2500usb_init_led(rt2x00dev, &rt2x00dev->led_radio, LED_TYPE_RADIO); + if (value == LED_MODE_TXRX_ACTIVITY || + value == LED_MODE_DEFAULT || + value == LED_MODE_ASUS) + rt2500usb_init_led(rt2x00dev, &rt2x00dev->led_qual, + LED_TYPE_ACTIVITY); +#endif /* CONFIG_RT2X00_LIB_LEDS */ + + /* + * Detect if this device has an hardware controlled radio. + */ + if (rt2x00_get_field16(eeprom, EEPROM_ANTENNA_HARDWARE_RADIO)) + __set_bit(CAPABILITY_HW_BUTTON, &rt2x00dev->cap_flags); + + /* + * Read the RSSI <-> dBm offset information. + */ + eeprom = rt2x00_eeprom_read(rt2x00dev, EEPROM_CALIBRATE_OFFSET); + rt2x00dev->rssi_offset = + rt2x00_get_field16(eeprom, EEPROM_CALIBRATE_OFFSET_RSSI); + + return 0; +} + +/* + * RF value list for RF2522 + * Supports: 2.4 GHz + */ +static const struct rf_channel rf_vals_bg_2522[] = { + { 1, 0x00002050, 0x000c1fda, 0x00000101, 0 }, + { 2, 0x00002050, 0x000c1fee, 0x00000101, 0 }, + { 3, 0x00002050, 0x000c2002, 0x00000101, 0 }, + { 4, 0x00002050, 0x000c2016, 0x00000101, 0 }, + { 5, 0x00002050, 0x000c202a, 0x00000101, 0 }, + { 6, 0x00002050, 0x000c203e, 0x00000101, 0 }, + { 7, 0x00002050, 0x000c2052, 0x00000101, 0 }, + { 8, 0x00002050, 0x000c2066, 0x00000101, 0 }, + { 9, 0x00002050, 0x000c207a, 0x00000101, 0 }, + { 10, 0x00002050, 0x000c208e, 0x00000101, 0 }, + { 11, 0x00002050, 0x000c20a2, 0x00000101, 0 }, + { 12, 0x00002050, 0x000c20b6, 0x00000101, 0 }, + { 13, 0x00002050, 0x000c20ca, 0x00000101, 0 }, + { 14, 0x00002050, 0x000c20fa, 0x00000101, 0 }, +}; + +/* + * RF value list for RF2523 + * Supports: 2.4 GHz + */ +static const struct rf_channel rf_vals_bg_2523[] = { + { 1, 0x00022010, 0x00000c9e, 0x000e0111, 0x00000a1b }, + { 2, 0x00022010, 0x00000ca2, 0x000e0111, 0x00000a1b }, + { 3, 0x00022010, 0x00000ca6, 0x000e0111, 0x00000a1b }, + { 4, 0x00022010, 0x00000caa, 0x000e0111, 0x00000a1b }, + { 5, 0x00022010, 0x00000cae, 0x000e0111, 0x00000a1b }, + { 6, 0x00022010, 0x00000cb2, 0x000e0111, 0x00000a1b }, + { 7, 0x00022010, 0x00000cb6, 0x000e0111, 0x00000a1b }, + { 8, 0x00022010, 0x00000cba, 0x000e0111, 0x00000a1b }, + { 9, 0x00022010, 0x00000cbe, 0x000e0111, 0x00000a1b }, + { 10, 0x00022010, 0x00000d02, 0x000e0111, 0x00000a1b }, + { 11, 0x00022010, 0x00000d06, 0x000e0111, 0x00000a1b }, + { 12, 0x00022010, 0x00000d0a, 0x000e0111, 0x00000a1b }, + { 13, 0x00022010, 0x00000d0e, 0x000e0111, 0x00000a1b }, + { 14, 0x00022010, 0x00000d1a, 0x000e0111, 0x00000a03 }, +}; + +/* + * RF value list for RF2524 + * Supports: 2.4 GHz + */ +static const struct rf_channel rf_vals_bg_2524[] = { + { 1, 0x00032020, 0x00000c9e, 0x00000101, 0x00000a1b }, + { 2, 0x00032020, 0x00000ca2, 0x00000101, 0x00000a1b }, + { 3, 0x00032020, 0x00000ca6, 0x00000101, 0x00000a1b }, + { 4, 0x00032020, 0x00000caa, 0x00000101, 0x00000a1b }, + { 5, 0x00032020, 0x00000cae, 0x00000101, 0x00000a1b }, + { 6, 0x00032020, 0x00000cb2, 0x00000101, 0x00000a1b }, + { 7, 0x00032020, 0x00000cb6, 0x00000101, 0x00000a1b }, + { 8, 0x00032020, 0x00000cba, 0x00000101, 0x00000a1b }, + { 9, 0x00032020, 0x00000cbe, 0x00000101, 0x00000a1b }, + { 10, 0x00032020, 0x00000d02, 0x00000101, 0x00000a1b }, + { 11, 0x00032020, 0x00000d06, 0x00000101, 0x00000a1b }, + { 12, 0x00032020, 0x00000d0a, 0x00000101, 0x00000a1b }, + { 13, 0x00032020, 0x00000d0e, 0x00000101, 0x00000a1b }, + { 14, 0x00032020, 0x00000d1a, 0x00000101, 0x00000a03 }, +}; + +/* + * RF value list for RF2525 + * Supports: 2.4 GHz + */ +static const struct rf_channel rf_vals_bg_2525[] = { + { 1, 0x00022020, 0x00080c9e, 0x00060111, 0x00000a1b }, + { 2, 0x00022020, 0x00080ca2, 0x00060111, 0x00000a1b }, + { 3, 0x00022020, 0x00080ca6, 0x00060111, 0x00000a1b }, + { 4, 0x00022020, 0x00080caa, 0x00060111, 0x00000a1b }, + { 5, 0x00022020, 0x00080cae, 0x00060111, 0x00000a1b }, + { 6, 0x00022020, 0x00080cb2, 0x00060111, 0x00000a1b }, + { 7, 0x00022020, 0x00080cb6, 0x00060111, 0x00000a1b }, + { 8, 0x00022020, 0x00080cba, 0x00060111, 0x00000a1b }, + { 9, 0x00022020, 0x00080cbe, 0x00060111, 0x00000a1b }, + { 10, 0x00022020, 0x00080d02, 0x00060111, 0x00000a1b }, + { 11, 0x00022020, 0x00080d06, 0x00060111, 0x00000a1b }, + { 12, 0x00022020, 0x00080d0a, 0x00060111, 0x00000a1b }, + { 13, 0x00022020, 0x00080d0e, 0x00060111, 0x00000a1b }, + { 14, 0x00022020, 0x00080d1a, 0x00060111, 0x00000a03 }, +}; + +/* + * RF value list for RF2525e + * Supports: 2.4 GHz + */ +static const struct rf_channel rf_vals_bg_2525e[] = { + { 1, 0x00022010, 0x0000089a, 0x00060111, 0x00000e1b }, + { 2, 0x00022010, 0x0000089e, 0x00060111, 0x00000e07 }, + { 3, 0x00022010, 0x0000089e, 0x00060111, 0x00000e1b }, + { 4, 0x00022010, 0x000008a2, 0x00060111, 0x00000e07 }, + { 5, 0x00022010, 0x000008a2, 0x00060111, 0x00000e1b }, + { 6, 0x00022010, 0x000008a6, 0x00060111, 0x00000e07 }, + { 7, 0x00022010, 0x000008a6, 0x00060111, 0x00000e1b }, + { 8, 0x00022010, 0x000008aa, 0x00060111, 0x00000e07 }, + { 9, 0x00022010, 0x000008aa, 0x00060111, 0x00000e1b }, + { 10, 0x00022010, 0x000008ae, 0x00060111, 0x00000e07 }, + { 11, 0x00022010, 0x000008ae, 0x00060111, 0x00000e1b }, + { 12, 0x00022010, 0x000008b2, 0x00060111, 0x00000e07 }, + { 13, 0x00022010, 0x000008b2, 0x00060111, 0x00000e1b }, + { 14, 0x00022010, 0x000008b6, 0x00060111, 0x00000e23 }, +}; + +/* + * RF value list for RF5222 + * Supports: 2.4 GHz & 5.2 GHz + */ +static const struct rf_channel rf_vals_5222[] = { + { 1, 0x00022020, 0x00001136, 0x00000101, 0x00000a0b }, + { 2, 0x00022020, 0x0000113a, 0x00000101, 0x00000a0b }, + { 3, 0x00022020, 0x0000113e, 0x00000101, 0x00000a0b }, + { 4, 0x00022020, 0x00001182, 0x00000101, 0x00000a0b }, + { 5, 0x00022020, 0x00001186, 0x00000101, 0x00000a0b }, + { 6, 0x00022020, 0x0000118a, 0x00000101, 0x00000a0b }, + { 7, 0x00022020, 0x0000118e, 0x00000101, 0x00000a0b }, + { 8, 0x00022020, 0x00001192, 0x00000101, 0x00000a0b }, + { 9, 0x00022020, 0x00001196, 0x00000101, 0x00000a0b }, + { 10, 0x00022020, 0x0000119a, 0x00000101, 0x00000a0b }, + { 11, 0x00022020, 0x0000119e, 0x00000101, 0x00000a0b }, + { 12, 0x00022020, 0x000011a2, 0x00000101, 0x00000a0b }, + { 13, 0x00022020, 0x000011a6, 0x00000101, 0x00000a0b }, + { 14, 0x00022020, 0x000011ae, 0x00000101, 0x00000a1b }, + + /* 802.11 UNI / HyperLan 2 */ + { 36, 0x00022010, 0x00018896, 0x00000101, 0x00000a1f }, + { 40, 0x00022010, 0x0001889a, 0x00000101, 0x00000a1f }, + { 44, 0x00022010, 0x0001889e, 0x00000101, 0x00000a1f }, + { 48, 0x00022010, 0x000188a2, 0x00000101, 0x00000a1f }, + { 52, 0x00022010, 0x000188a6, 0x00000101, 0x00000a1f }, + { 66, 0x00022010, 0x000188aa, 0x00000101, 0x00000a1f }, + { 60, 0x00022010, 0x000188ae, 0x00000101, 0x00000a1f }, + { 64, 0x00022010, 0x000188b2, 0x00000101, 0x00000a1f }, + + /* 802.11 HyperLan 2 */ + { 100, 0x00022010, 0x00008802, 0x00000101, 0x00000a0f }, + { 104, 0x00022010, 0x00008806, 0x00000101, 0x00000a0f }, + { 108, 0x00022010, 0x0000880a, 0x00000101, 0x00000a0f }, + { 112, 0x00022010, 0x0000880e, 0x00000101, 0x00000a0f }, + { 116, 0x00022010, 0x00008812, 0x00000101, 0x00000a0f }, + { 120, 0x00022010, 0x00008816, 0x00000101, 0x00000a0f }, + { 124, 0x00022010, 0x0000881a, 0x00000101, 0x00000a0f }, + { 128, 0x00022010, 0x0000881e, 0x00000101, 0x00000a0f }, + { 132, 0x00022010, 0x00008822, 0x00000101, 0x00000a0f }, + { 136, 0x00022010, 0x00008826, 0x00000101, 0x00000a0f }, + + /* 802.11 UNII */ + { 140, 0x00022010, 0x0000882a, 0x00000101, 0x00000a0f }, + { 149, 0x00022020, 0x000090a6, 0x00000101, 0x00000a07 }, + { 153, 0x00022020, 0x000090ae, 0x00000101, 0x00000a07 }, + { 157, 0x00022020, 0x000090b6, 0x00000101, 0x00000a07 }, + { 161, 0x00022020, 0x000090be, 0x00000101, 0x00000a07 }, +}; + +static int rt2500usb_probe_hw_mode(struct rt2x00_dev *rt2x00dev) +{ + struct hw_mode_spec *spec = &rt2x00dev->spec; + struct channel_info *info; + u8 *tx_power; + unsigned int i; + + /* + * Initialize all hw fields. + * + * Don't set IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING unless we are + * capable of sending the buffered frames out after the DTIM + * transmission using rt2x00lib_beacondone. This will send out + * multicast and broadcast traffic immediately instead of buffering it + * infinitly and thus dropping it after some time. + */ + ieee80211_hw_set(rt2x00dev->hw, PS_NULLFUNC_STACK); + ieee80211_hw_set(rt2x00dev->hw, SUPPORTS_PS); + ieee80211_hw_set(rt2x00dev->hw, RX_INCLUDES_FCS); + ieee80211_hw_set(rt2x00dev->hw, SIGNAL_DBM); + + /* + * Disable powersaving as default. + */ + rt2x00dev->hw->wiphy->flags &= ~WIPHY_FLAG_PS_ON_BY_DEFAULT; + + SET_IEEE80211_DEV(rt2x00dev->hw, rt2x00dev->dev); + SET_IEEE80211_PERM_ADDR(rt2x00dev->hw, + rt2x00_eeprom_addr(rt2x00dev, + EEPROM_MAC_ADDR_0)); + + /* + * Initialize hw_mode information. + */ + spec->supported_bands = SUPPORT_BAND_2GHZ; + spec->supported_rates = SUPPORT_RATE_CCK | SUPPORT_RATE_OFDM; + + if (rt2x00_rf(rt2x00dev, RF2522)) { + spec->num_channels = ARRAY_SIZE(rf_vals_bg_2522); + spec->channels = rf_vals_bg_2522; + } else if (rt2x00_rf(rt2x00dev, RF2523)) { + spec->num_channels = ARRAY_SIZE(rf_vals_bg_2523); + spec->channels = rf_vals_bg_2523; + } else if (rt2x00_rf(rt2x00dev, RF2524)) { + spec->num_channels = ARRAY_SIZE(rf_vals_bg_2524); + spec->channels = rf_vals_bg_2524; + } else if (rt2x00_rf(rt2x00dev, RF2525)) { + spec->num_channels = ARRAY_SIZE(rf_vals_bg_2525); + spec->channels = rf_vals_bg_2525; + } else if (rt2x00_rf(rt2x00dev, RF2525E)) { + spec->num_channels = ARRAY_SIZE(rf_vals_bg_2525e); + spec->channels = rf_vals_bg_2525e; + } else if (rt2x00_rf(rt2x00dev, RF5222)) { + spec->supported_bands |= SUPPORT_BAND_5GHZ; + spec->num_channels = ARRAY_SIZE(rf_vals_5222); + spec->channels = rf_vals_5222; + } + + /* + * Create channel information array + */ + info = kcalloc(spec->num_channels, sizeof(*info), GFP_KERNEL); + if (!info) + return -ENOMEM; + + spec->channels_info = info; + + tx_power = rt2x00_eeprom_addr(rt2x00dev, EEPROM_TXPOWER_START); + for (i = 0; i < 14; i++) { + info[i].max_power = MAX_TXPOWER; + info[i].default_power1 = TXPOWER_FROM_DEV(tx_power[i]); + } + + if (spec->num_channels > 14) { + for (i = 14; i < spec->num_channels; i++) { + info[i].max_power = MAX_TXPOWER; + info[i].default_power1 = DEFAULT_TXPOWER; + } + } + + return 0; +} + +static int rt2500usb_probe_hw(struct rt2x00_dev *rt2x00dev) +{ + int retval; + u16 reg; + + /* + * Allocate eeprom data. + */ + retval = rt2500usb_validate_eeprom(rt2x00dev); + if (retval) + return retval; + + retval = rt2500usb_init_eeprom(rt2x00dev); + if (retval) + return retval; + + /* + * Enable rfkill polling by setting GPIO direction of the + * rfkill switch GPIO pin correctly. + */ + reg = rt2500usb_register_read(rt2x00dev, MAC_CSR19); + rt2x00_set_field16(®, MAC_CSR19_DIR0, 0); + rt2500usb_register_write(rt2x00dev, MAC_CSR19, reg); + + /* + * Initialize hw specifications. + */ + retval = rt2500usb_probe_hw_mode(rt2x00dev); + if (retval) + return retval; + + /* + * This device requires the atim queue + */ + __set_bit(REQUIRE_ATIM_QUEUE, &rt2x00dev->cap_flags); + __set_bit(REQUIRE_BEACON_GUARD, &rt2x00dev->cap_flags); + if (!modparam_nohwcrypt) { + __set_bit(CAPABILITY_HW_CRYPTO, &rt2x00dev->cap_flags); + __set_bit(REQUIRE_COPY_IV, &rt2x00dev->cap_flags); + } + __set_bit(REQUIRE_SW_SEQNO, &rt2x00dev->cap_flags); + __set_bit(REQUIRE_PS_AUTOWAKE, &rt2x00dev->cap_flags); + + /* + * Set the rssi offset. + */ + rt2x00dev->rssi_offset = DEFAULT_RSSI_OFFSET; + + return 0; +} + +static const struct ieee80211_ops rt2500usb_mac80211_ops = { + .tx = rt2x00mac_tx, + .start = rt2x00mac_start, + .stop = rt2x00mac_stop, + .add_interface = rt2x00mac_add_interface, + .remove_interface = rt2x00mac_remove_interface, + .config = rt2x00mac_config, + .configure_filter = rt2x00mac_configure_filter, + .set_tim = rt2x00mac_set_tim, + .set_key = rt2x00mac_set_key, + .sw_scan_start = rt2x00mac_sw_scan_start, + .sw_scan_complete = rt2x00mac_sw_scan_complete, + .get_stats = rt2x00mac_get_stats, + .bss_info_changed = rt2x00mac_bss_info_changed, + .conf_tx = rt2x00mac_conf_tx, + .rfkill_poll = rt2x00mac_rfkill_poll, + .flush = rt2x00mac_flush, + .set_antenna = rt2x00mac_set_antenna, + .get_antenna = rt2x00mac_get_antenna, + .get_ringparam = rt2x00mac_get_ringparam, + .tx_frames_pending = rt2x00mac_tx_frames_pending, +}; + +static const struct rt2x00lib_ops rt2500usb_rt2x00_ops = { + .probe_hw = rt2500usb_probe_hw, + .initialize = rt2x00usb_initialize, + .uninitialize = rt2x00usb_uninitialize, + .clear_entry = rt2x00usb_clear_entry, + .set_device_state = rt2500usb_set_device_state, + .rfkill_poll = rt2500usb_rfkill_poll, + .link_stats = rt2500usb_link_stats, + .reset_tuner = rt2500usb_reset_tuner, + .watchdog = rt2x00usb_watchdog, + .start_queue = rt2500usb_start_queue, + .kick_queue = rt2x00usb_kick_queue, + .stop_queue = rt2500usb_stop_queue, + .flush_queue = rt2x00usb_flush_queue, + .write_tx_desc = rt2500usb_write_tx_desc, + .write_beacon = rt2500usb_write_beacon, + .get_tx_data_len = rt2500usb_get_tx_data_len, + .fill_rxdone = rt2500usb_fill_rxdone, + .config_shared_key = rt2500usb_config_key, + .config_pairwise_key = rt2500usb_config_key, + .config_filter = rt2500usb_config_filter, + .config_intf = rt2500usb_config_intf, + .config_erp = rt2500usb_config_erp, + .config_ant = rt2500usb_config_ant, + .config = rt2500usb_config, +}; + +static void rt2500usb_queue_init(struct data_queue *queue) +{ + switch (queue->qid) { + case QID_RX: + queue->limit = 32; + queue->data_size = DATA_FRAME_SIZE; + queue->desc_size = RXD_DESC_SIZE; + queue->priv_size = sizeof(struct queue_entry_priv_usb); + break; + + case QID_AC_VO: + case QID_AC_VI: + case QID_AC_BE: + case QID_AC_BK: + queue->limit = 32; + queue->data_size = DATA_FRAME_SIZE; + queue->desc_size = TXD_DESC_SIZE; + queue->priv_size = sizeof(struct queue_entry_priv_usb); + break; + + case QID_BEACON: + queue->limit = 1; + queue->data_size = MGMT_FRAME_SIZE; + queue->desc_size = TXD_DESC_SIZE; + queue->priv_size = sizeof(struct queue_entry_priv_usb_bcn); + break; + + case QID_ATIM: + queue->limit = 8; + queue->data_size = DATA_FRAME_SIZE; + queue->desc_size = TXD_DESC_SIZE; + queue->priv_size = sizeof(struct queue_entry_priv_usb); + break; + + default: + BUG(); + break; + } +} + +static const struct rt2x00_ops rt2500usb_ops = { + .name = KBUILD_MODNAME, + .max_ap_intf = 1, + .eeprom_size = EEPROM_SIZE, + .rf_size = RF_SIZE, + .tx_queues = NUM_TX_QUEUES, + .queue_init = rt2500usb_queue_init, + .lib = &rt2500usb_rt2x00_ops, + .hw = &rt2500usb_mac80211_ops, +#ifdef CONFIG_RT2X00_LIB_DEBUGFS + .debugfs = &rt2500usb_rt2x00debug, +#endif /* CONFIG_RT2X00_LIB_DEBUGFS */ +}; + +/* + * rt2500usb module information. + */ +static const struct usb_device_id rt2500usb_device_table[] = { + /* ASUS */ + { USB_DEVICE(0x0b05, 0x1706) }, + { USB_DEVICE(0x0b05, 0x1707) }, + /* Belkin */ + { USB_DEVICE(0x050d, 0x7050) }, /* FCC ID: K7SF5D7050A ver. 2.x */ + { USB_DEVICE(0x050d, 0x7051) }, + /* Cisco Systems */ + { USB_DEVICE(0x13b1, 0x000d) }, + { USB_DEVICE(0x13b1, 0x0011) }, + { USB_DEVICE(0x13b1, 0x001a) }, + /* Conceptronic */ + { USB_DEVICE(0x14b2, 0x3c02) }, + /* D-LINK */ + { USB_DEVICE(0x2001, 0x3c00) }, + /* Gigabyte */ + { USB_DEVICE(0x1044, 0x8001) }, + { USB_DEVICE(0x1044, 0x8007) }, + /* Hercules */ + { USB_DEVICE(0x06f8, 0xe000) }, + /* Melco */ + { USB_DEVICE(0x0411, 0x005e) }, + { USB_DEVICE(0x0411, 0x0066) }, + { USB_DEVICE(0x0411, 0x0067) }, + { USB_DEVICE(0x0411, 0x008b) }, + { USB_DEVICE(0x0411, 0x0097) }, + /* MSI */ + { USB_DEVICE(0x0db0, 0x6861) }, + { USB_DEVICE(0x0db0, 0x6865) }, + { USB_DEVICE(0x0db0, 0x6869) }, + /* Ralink */ + { USB_DEVICE(0x148f, 0x1706) }, + { USB_DEVICE(0x148f, 0x2570) }, + { USB_DEVICE(0x148f, 0x9020) }, + /* Sagem */ + { USB_DEVICE(0x079b, 0x004b) }, + /* Siemens */ + { USB_DEVICE(0x0681, 0x3c06) }, + /* SMC */ + { USB_DEVICE(0x0707, 0xee13) }, + /* Spairon */ + { USB_DEVICE(0x114b, 0x0110) }, + /* SURECOM */ + { USB_DEVICE(0x0769, 0x11f3) }, + /* Trust */ + { USB_DEVICE(0x0eb0, 0x9020) }, + /* VTech */ + { USB_DEVICE(0x0f88, 0x3012) }, + /* Zinwell */ + { USB_DEVICE(0x5a57, 0x0260) }, + { 0, } +}; + +MODULE_AUTHOR(DRV_PROJECT); +MODULE_VERSION(DRV_VERSION); +MODULE_DESCRIPTION("Ralink RT2500 USB Wireless LAN driver."); +MODULE_DEVICE_TABLE(usb, rt2500usb_device_table); +MODULE_LICENSE("GPL"); + +static int rt2500usb_probe(struct usb_interface *usb_intf, + const struct usb_device_id *id) +{ + return rt2x00usb_probe(usb_intf, &rt2500usb_ops); +} + +static struct usb_driver rt2500usb_driver = { + .name = KBUILD_MODNAME, + .id_table = rt2500usb_device_table, + .probe = rt2500usb_probe, + .disconnect = rt2x00usb_disconnect, + .suspend = rt2x00usb_suspend, + .resume = rt2x00usb_resume, + .reset_resume = rt2x00usb_resume, + .disable_hub_initiated_lpm = 1, +}; + +module_usb_driver(rt2500usb_driver); |