summaryrefslogtreecommitdiffstats
path: root/drivers/net/wireless/ti/wl1251/reg.h
diff options
context:
space:
mode:
Diffstat (limited to '')
-rw-r--r--drivers/net/wireless/ti/wl1251/reg.h641
1 files changed, 641 insertions, 0 deletions
diff --git a/drivers/net/wireless/ti/wl1251/reg.h b/drivers/net/wireless/ti/wl1251/reg.h
new file mode 100644
index 000000000..890176c91
--- /dev/null
+++ b/drivers/net/wireless/ti/wl1251/reg.h
@@ -0,0 +1,641 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * This file is part of wl12xx
+ *
+ * Copyright (c) 1998-2007 Texas Instruments Incorporated
+ * Copyright (C) 2008 Nokia Corporation
+ */
+
+#ifndef __REG_H__
+#define __REG_H__
+
+#include <linux/bitops.h>
+
+#define REGISTERS_BASE 0x00300000
+#define DRPW_BASE 0x00310000
+
+#define REGISTERS_DOWN_SIZE 0x00008800
+#define REGISTERS_WORK_SIZE 0x0000b000
+
+#define HW_ACCESS_ELP_CTRL_REG_ADDR 0x1FFFC
+
+/* ELP register commands */
+#define ELPCTRL_WAKE_UP 0x1
+#define ELPCTRL_WAKE_UP_WLAN_READY 0x5
+#define ELPCTRL_SLEEP 0x0
+/* ELP WLAN_READY bit */
+#define ELPCTRL_WLAN_READY 0x2
+
+/* Device Configuration registers*/
+#define SOR_CFG (REGISTERS_BASE + 0x0800)
+#define ECPU_CTRL (REGISTERS_BASE + 0x0804)
+#define HI_CFG (REGISTERS_BASE + 0x0808)
+
+/* EEPROM registers */
+#define EE_START (REGISTERS_BASE + 0x080C)
+#define EE_CTL (REGISTERS_BASE + 0x2000)
+#define EE_DATA (REGISTERS_BASE + 0x2004)
+#define EE_ADDR (REGISTERS_BASE + 0x2008)
+
+#define EE_CTL_READ 2
+
+#define CHIP_ID_B (REGISTERS_BASE + 0x5674)
+
+#define CHIP_ID_1251_PG10 (0x7010101)
+#define CHIP_ID_1251_PG11 (0x7020101)
+#define CHIP_ID_1251_PG12 (0x7030101)
+
+#define ENABLE (REGISTERS_BASE + 0x5450)
+
+/* Power Management registers */
+#define ELP_CFG_MODE (REGISTERS_BASE + 0x5804)
+#define ELP_CMD (REGISTERS_BASE + 0x5808)
+#define PLL_CAL_TIME (REGISTERS_BASE + 0x5810)
+#define CLK_REQ_TIME (REGISTERS_BASE + 0x5814)
+#define CLK_BUF_TIME (REGISTERS_BASE + 0x5818)
+
+#define CFG_PLL_SYNC_CNT (REGISTERS_BASE + 0x5820)
+
+/* Scratch Pad registers*/
+#define SCR_PAD0 (REGISTERS_BASE + 0x5608)
+#define SCR_PAD1 (REGISTERS_BASE + 0x560C)
+#define SCR_PAD2 (REGISTERS_BASE + 0x5610)
+#define SCR_PAD3 (REGISTERS_BASE + 0x5614)
+#define SCR_PAD4 (REGISTERS_BASE + 0x5618)
+#define SCR_PAD4_SET (REGISTERS_BASE + 0x561C)
+#define SCR_PAD4_CLR (REGISTERS_BASE + 0x5620)
+#define SCR_PAD5 (REGISTERS_BASE + 0x5624)
+#define SCR_PAD5_SET (REGISTERS_BASE + 0x5628)
+#define SCR_PAD5_CLR (REGISTERS_BASE + 0x562C)
+#define SCR_PAD6 (REGISTERS_BASE + 0x5630)
+#define SCR_PAD7 (REGISTERS_BASE + 0x5634)
+#define SCR_PAD8 (REGISTERS_BASE + 0x5638)
+#define SCR_PAD9 (REGISTERS_BASE + 0x563C)
+
+/* Spare registers*/
+#define SPARE_A1 (REGISTERS_BASE + 0x0994)
+#define SPARE_A2 (REGISTERS_BASE + 0x0998)
+#define SPARE_A3 (REGISTERS_BASE + 0x099C)
+#define SPARE_A4 (REGISTERS_BASE + 0x09A0)
+#define SPARE_A5 (REGISTERS_BASE + 0x09A4)
+#define SPARE_A6 (REGISTERS_BASE + 0x09A8)
+#define SPARE_A7 (REGISTERS_BASE + 0x09AC)
+#define SPARE_A8 (REGISTERS_BASE + 0x09B0)
+#define SPARE_B1 (REGISTERS_BASE + 0x5420)
+#define SPARE_B2 (REGISTERS_BASE + 0x5424)
+#define SPARE_B3 (REGISTERS_BASE + 0x5428)
+#define SPARE_B4 (REGISTERS_BASE + 0x542C)
+#define SPARE_B5 (REGISTERS_BASE + 0x5430)
+#define SPARE_B6 (REGISTERS_BASE + 0x5434)
+#define SPARE_B7 (REGISTERS_BASE + 0x5438)
+#define SPARE_B8 (REGISTERS_BASE + 0x543C)
+
+enum wl12xx_acx_int_reg {
+ ACX_REG_INTERRUPT_TRIG,
+ ACX_REG_INTERRUPT_TRIG_H,
+
+/*=============================================
+ Host Interrupt Mask Register - 32bit (RW)
+ ------------------------------------------
+ Setting a bit in this register masks the
+ corresponding interrupt to the host.
+ 0 - RX0 - Rx first dubble buffer Data Interrupt
+ 1 - TXD - Tx Data Interrupt
+ 2 - TXXFR - Tx Transfer Interrupt
+ 3 - RX1 - Rx second dubble buffer Data Interrupt
+ 4 - RXXFR - Rx Transfer Interrupt
+ 5 - EVENT_A - Event Mailbox interrupt
+ 6 - EVENT_B - Event Mailbox interrupt
+ 7 - WNONHST - Wake On Host Interrupt
+ 8 - TRACE_A - Debug Trace interrupt
+ 9 - TRACE_B - Debug Trace interrupt
+ 10 - CDCMP - Command Complete Interrupt
+ 11 -
+ 12 -
+ 13 -
+ 14 - ICOMP - Initialization Complete Interrupt
+ 16 - SG SE - Soft Gemini - Sense enable interrupt
+ 17 - SG SD - Soft Gemini - Sense disable interrupt
+ 18 - -
+ 19 - -
+ 20 - -
+ 21- -
+ Default: 0x0001
+*==============================================*/
+ ACX_REG_INTERRUPT_MASK,
+
+/*=============================================
+ Host Interrupt Mask Set 16bit, (Write only)
+ ------------------------------------------
+ Setting a bit in this register sets
+ the corresponding bin in ACX_HINT_MASK register
+ without effecting the mask
+ state of other bits (0 = no effect).
+==============================================*/
+ ACX_REG_HINT_MASK_SET,
+
+/*=============================================
+ Host Interrupt Mask Clear 16bit,(Write only)
+ ------------------------------------------
+ Setting a bit in this register clears
+ the corresponding bin in ACX_HINT_MASK register
+ without effecting the mask
+ state of other bits (0 = no effect).
+=============================================*/
+ ACX_REG_HINT_MASK_CLR,
+
+/*=============================================
+ Host Interrupt Status Nondestructive Read
+ 16bit,(Read only)
+ ------------------------------------------
+ The host can read this register to determine
+ which interrupts are active.
+ Reading this register doesn't
+ effect its content.
+=============================================*/
+ ACX_REG_INTERRUPT_NO_CLEAR,
+
+/*=============================================
+ Host Interrupt Status Clear on Read Register
+ 16bit,(Read only)
+ ------------------------------------------
+ The host can read this register to determine
+ which interrupts are active.
+ Reading this register clears it,
+ thus making all interrupts inactive.
+==============================================*/
+ ACX_REG_INTERRUPT_CLEAR,
+
+/*=============================================
+ Host Interrupt Acknowledge Register
+ 16bit,(Write only)
+ ------------------------------------------
+ The host can set individual bits in this
+ register to clear (acknowledge) the corresp.
+ interrupt status bits in the HINT_STS_CLR and
+ HINT_STS_ND registers, thus making the
+ assotiated interrupt inactive. (0-no effect)
+==============================================*/
+ ACX_REG_INTERRUPT_ACK,
+
+/*===============================================
+ Host Software Reset - 32bit RW
+ ------------------------------------------
+ [31:1] Reserved
+ 0 SOFT_RESET Soft Reset - When this bit is set,
+ it holds the Wlan hardware in a soft reset state.
+ This reset disables all MAC and baseband processor
+ clocks except the CardBus/PCI interface clock.
+ It also initializes all MAC state machines except
+ the host interface. It does not reload the
+ contents of the EEPROM. When this bit is cleared
+ (not self-clearing), the Wlan hardware
+ exits the software reset state.
+===============================================*/
+ ACX_REG_SLV_SOFT_RESET,
+
+/*===============================================
+ EEPROM Burst Read Start - 32bit RW
+ ------------------------------------------
+ [31:1] Reserved
+ 0 ACX_EE_START - EEPROM Burst Read Start 0
+ Setting this bit starts a burst read from
+ the external EEPROM.
+ If this bit is set (after reset) before an EEPROM read/write,
+ the burst read starts at EEPROM address 0.
+ Otherwise, it starts at the address
+ following the address of the previous access.
+ TheWlan hardware hardware clears this bit automatically.
+
+ Default: 0x00000000
+*================================================*/
+ ACX_REG_EE_START,
+
+/* Embedded ARM CPU Control */
+
+/*===============================================
+ Halt eCPU - 32bit RW
+ ------------------------------------------
+ 0 HALT_ECPU Halt Embedded CPU - This bit is the
+ complement of bit 1 (MDATA2) in the SOR_CFG register.
+ During a hardware reset, this bit holds
+ the inverse of MDATA2.
+ When downloading firmware from the host,
+ set this bit (pull down MDATA2).
+ The host clears this bit after downloading the firmware into
+ zero-wait-state SSRAM.
+ When loading firmware from Flash, clear this bit (pull up MDATA2)
+ so that the eCPU can run the bootloader code in Flash
+ HALT_ECPU eCPU State
+ --------------------
+ 1 halt eCPU
+ 0 enable eCPU
+ ===============================================*/
+ ACX_REG_ECPU_CONTROL,
+
+ ACX_REG_TABLE_LEN
+};
+
+#define ACX_SLV_SOFT_RESET_BIT BIT(0)
+#define ACX_REG_EEPROM_START_BIT BIT(0)
+
+/* Command/Information Mailbox Pointers */
+
+/*===============================================
+ Command Mailbox Pointer - 32bit RW
+ ------------------------------------------
+ This register holds the start address of
+ the command mailbox located in the Wlan hardware memory.
+ The host must read this pointer after a reset to
+ find the location of the command mailbox.
+ The Wlan hardware initializes the command mailbox
+ pointer with the default address of the command mailbox.
+ The command mailbox pointer is not valid until after
+ the host receives the Init Complete interrupt from
+ the Wlan hardware.
+ ===============================================*/
+#define REG_COMMAND_MAILBOX_PTR (SCR_PAD0)
+
+/*===============================================
+ Information Mailbox Pointer - 32bit RW
+ ------------------------------------------
+ This register holds the start address of
+ the information mailbox located in the Wlan hardware memory.
+ The host must read this pointer after a reset to find
+ the location of the information mailbox.
+ The Wlan hardware initializes the information mailbox pointer
+ with the default address of the information mailbox.
+ The information mailbox pointer is not valid
+ until after the host receives the Init Complete interrupt from
+ the Wlan hardware.
+ ===============================================*/
+#define REG_EVENT_MAILBOX_PTR (SCR_PAD1)
+
+
+/* Misc */
+
+#define REG_ENABLE_TX_RX (ENABLE)
+/*
+ * Rx configuration (filter) information element
+ * ---------------------------------------------
+ */
+#define REG_RX_CONFIG (RX_CFG)
+#define REG_RX_FILTER (RX_FILTER_CFG)
+
+
+#define RX_CFG_ENABLE_PHY_HEADER_PLCP 0x0002
+
+/* promiscuous - receives all valid frames */
+#define RX_CFG_PROMISCUOUS 0x0008
+
+/* receives frames from any BSSID */
+#define RX_CFG_BSSID 0x0020
+
+/* receives frames destined to any MAC address */
+#define RX_CFG_MAC 0x0010
+
+#define RX_CFG_ENABLE_ONLY_MY_DEST_MAC 0x0010
+#define RX_CFG_ENABLE_ANY_DEST_MAC 0x0000
+#define RX_CFG_ENABLE_ONLY_MY_BSSID 0x0020
+#define RX_CFG_ENABLE_ANY_BSSID 0x0000
+
+/* discards all broadcast frames */
+#define RX_CFG_DISABLE_BCAST 0x0200
+
+#define RX_CFG_ENABLE_ONLY_MY_SSID 0x0400
+#define RX_CFG_ENABLE_RX_CMPLT_FCS_ERROR 0x0800
+#define RX_CFG_COPY_RX_STATUS 0x2000
+#define RX_CFG_TSF 0x10000
+
+#define RX_CONFIG_OPTION_ANY_DST_MY_BSS (RX_CFG_ENABLE_ANY_DEST_MAC | \
+ RX_CFG_ENABLE_ONLY_MY_BSSID)
+
+#define RX_CONFIG_OPTION_MY_DST_ANY_BSS (RX_CFG_ENABLE_ONLY_MY_DEST_MAC\
+ | RX_CFG_ENABLE_ANY_BSSID)
+
+#define RX_CONFIG_OPTION_ANY_DST_ANY_BSS (RX_CFG_ENABLE_ANY_DEST_MAC | \
+ RX_CFG_ENABLE_ANY_BSSID)
+
+#define RX_CONFIG_OPTION_MY_DST_MY_BSS (RX_CFG_ENABLE_ONLY_MY_DEST_MAC\
+ | RX_CFG_ENABLE_ONLY_MY_BSSID)
+
+#define RX_CONFIG_OPTION_FOR_SCAN (RX_CFG_ENABLE_PHY_HEADER_PLCP \
+ | RX_CFG_ENABLE_RX_CMPLT_FCS_ERROR \
+ | RX_CFG_COPY_RX_STATUS | RX_CFG_TSF)
+
+#define RX_CONFIG_OPTION_FOR_MEASUREMENT (RX_CFG_ENABLE_ANY_DEST_MAC)
+
+#define RX_CONFIG_OPTION_FOR_JOIN (RX_CFG_ENABLE_ONLY_MY_BSSID | \
+ RX_CFG_ENABLE_ONLY_MY_DEST_MAC)
+
+#define RX_CONFIG_OPTION_FOR_IBSS_JOIN (RX_CFG_ENABLE_ONLY_MY_SSID | \
+ RX_CFG_ENABLE_ONLY_MY_DEST_MAC)
+
+#define RX_FILTER_OPTION_DEF (CFG_RX_MGMT_EN | CFG_RX_DATA_EN\
+ | CFG_RX_CTL_EN | CFG_RX_BCN_EN\
+ | CFG_RX_AUTH_EN | CFG_RX_ASSOC_EN)
+
+#define RX_FILTER_OPTION_FILTER_ALL 0
+
+#define RX_FILTER_OPTION_DEF_PRSP_BCN (CFG_RX_PRSP_EN | CFG_RX_MGMT_EN\
+ | CFG_RX_RCTS_ACK | CFG_RX_BCN_EN)
+
+#define RX_FILTER_OPTION_JOIN (CFG_RX_MGMT_EN | CFG_RX_DATA_EN\
+ | CFG_RX_BCN_EN | CFG_RX_AUTH_EN\
+ | CFG_RX_ASSOC_EN | CFG_RX_RCTS_ACK\
+ | CFG_RX_PRSP_EN)
+
+
+/*===============================================
+ EEPROM Read/Write Request 32bit RW
+ ------------------------------------------
+ 1 EE_READ - EEPROM Read Request 1 - Setting this bit
+ loads a single byte of data into the EE_DATA
+ register from the EEPROM location specified in
+ the EE_ADDR register.
+ The Wlan hardware hardware clears this bit automatically.
+ EE_DATA is valid when this bit is cleared.
+
+ 0 EE_WRITE - EEPROM Write Request - Setting this bit
+ writes a single byte of data from the EE_DATA register into the
+ EEPROM location specified in the EE_ADDR register.
+ The Wlan hardware hardware clears this bit automatically.
+*===============================================*/
+#define EE_CTL (REGISTERS_BASE + 0x2000)
+#define ACX_EE_CTL_REG EE_CTL
+#define EE_WRITE 0x00000001ul
+#define EE_READ 0x00000002ul
+
+/*===============================================
+ EEPROM Address - 32bit RW
+ ------------------------------------------
+ This register specifies the address
+ within the EEPROM from/to which to read/write data.
+ ===============================================*/
+#define EE_ADDR (REGISTERS_BASE + 0x2008)
+#define ACX_EE_ADDR_REG EE_ADDR
+
+/*===============================================
+ EEPROM Data - 32bit RW
+ ------------------------------------------
+ This register either holds the read 8 bits of
+ data from the EEPROM or the write data
+ to be written to the EEPROM.
+ ===============================================*/
+#define EE_DATA (REGISTERS_BASE + 0x2004)
+#define ACX_EE_DATA_REG EE_DATA
+
+#define EEPROM_ACCESS_TO 10000 /* timeout counter */
+#define START_EEPROM_MGR 0x00000001
+
+/*===============================================
+ EEPROM Base Address - 32bit RW
+ ------------------------------------------
+ This register holds the upper nine bits
+ [23:15] of the 24-bit Wlan hardware memory
+ address for burst reads from EEPROM accesses.
+ The EEPROM provides the lower 15 bits of this address.
+ The MSB of the address from the EEPROM is ignored.
+ ===============================================*/
+#define ACX_EE_CFG EE_CFG
+
+/*===============================================
+ GPIO Output Values -32bit, RW
+ ------------------------------------------
+ [31:16] Reserved
+ [15: 0] Specify the output values (at the output driver inputs) for
+ GPIO[15:0], respectively.
+ ===============================================*/
+#define ACX_GPIO_OUT_REG GPIO_OUT
+#define ACX_MAX_GPIO_LINES 15
+
+/*===============================================
+ Contention window -32bit, RW
+ ------------------------------------------
+ [31:26] Reserved
+ [25:16] Max (0x3ff)
+ [15:07] Reserved
+ [06:00] Current contention window value - default is 0x1F
+ ===============================================*/
+#define ACX_CONT_WIND_CFG_REG CONT_WIND_CFG
+#define ACX_CONT_WIND_MIN_MASK 0x0000007f
+#define ACX_CONT_WIND_MAX 0x03ff0000
+
+/*===============================================
+ HI_CFG Interface Configuration Register Values
+ ------------------------------------------
+ ===============================================*/
+#define HI_CFG_UART_ENABLE 0x00000004
+#define HI_CFG_RST232_ENABLE 0x00000008
+#define HI_CFG_CLOCK_REQ_SELECT 0x00000010
+#define HI_CFG_HOST_INT_ENABLE 0x00000020
+#define HI_CFG_VLYNQ_OUTPUT_ENABLE 0x00000040
+#define HI_CFG_HOST_INT_ACTIVE_LOW 0x00000080
+#define HI_CFG_UART_TX_OUT_GPIO_15 0x00000100
+#define HI_CFG_UART_TX_OUT_GPIO_14 0x00000200
+#define HI_CFG_UART_TX_OUT_GPIO_7 0x00000400
+
+/*
+ * NOTE: USE_ACTIVE_HIGH compilation flag should be defined in makefile
+ * for platforms using active high interrupt level
+ */
+#ifdef USE_ACTIVE_HIGH
+#define HI_CFG_DEF_VAL \
+ (HI_CFG_UART_ENABLE | \
+ HI_CFG_RST232_ENABLE | \
+ HI_CFG_CLOCK_REQ_SELECT | \
+ HI_CFG_HOST_INT_ENABLE)
+#else
+#define HI_CFG_DEF_VAL \
+ (HI_CFG_UART_ENABLE | \
+ HI_CFG_RST232_ENABLE | \
+ HI_CFG_CLOCK_REQ_SELECT | \
+ HI_CFG_HOST_INT_ENABLE)
+
+#endif
+
+#define REF_FREQ_19_2 0
+#define REF_FREQ_26_0 1
+#define REF_FREQ_38_4 2
+#define REF_FREQ_40_0 3
+#define REF_FREQ_33_6 4
+#define REF_FREQ_NUM 5
+
+#define LUT_PARAM_INTEGER_DIVIDER 0
+#define LUT_PARAM_FRACTIONAL_DIVIDER 1
+#define LUT_PARAM_ATTN_BB 2
+#define LUT_PARAM_ALPHA_BB 3
+#define LUT_PARAM_STOP_TIME_BB 4
+#define LUT_PARAM_BB_PLL_LOOP_FILTER 5
+#define LUT_PARAM_NUM 6
+
+#define ACX_EEPROMLESS_IND_REG (SCR_PAD4)
+#define USE_EEPROM 0
+#define SOFT_RESET_MAX_TIME 1000000
+#define SOFT_RESET_STALL_TIME 1000
+#define NVS_DATA_BUNDARY_ALIGNMENT 4
+
+
+/* Firmware image load chunk size */
+#define CHUNK_SIZE 512
+
+/* Firmware image header size */
+#define FW_HDR_SIZE 8
+
+#define ECPU_CONTROL_HALT 0x00000101
+
+
+/******************************************************************************
+
+ CHANNELS, BAND & REG DOMAINS definitions
+
+******************************************************************************/
+
+
+enum {
+ RADIO_BAND_2_4GHZ = 0, /* 2.4 Ghz band */
+ RADIO_BAND_5GHZ = 1, /* 5 Ghz band */
+ RADIO_BAND_JAPAN_4_9_GHZ = 2,
+ DEFAULT_BAND = RADIO_BAND_2_4GHZ,
+ INVALID_BAND = 0xFE,
+ MAX_RADIO_BANDS = 0xFF
+};
+
+enum {
+ NO_RATE = 0,
+ RATE_1MBPS = 0x0A,
+ RATE_2MBPS = 0x14,
+ RATE_5_5MBPS = 0x37,
+ RATE_6MBPS = 0x0B,
+ RATE_9MBPS = 0x0F,
+ RATE_11MBPS = 0x6E,
+ RATE_12MBPS = 0x0A,
+ RATE_18MBPS = 0x0E,
+ RATE_22MBPS = 0xDC,
+ RATE_24MBPS = 0x09,
+ RATE_36MBPS = 0x0D,
+ RATE_48MBPS = 0x08,
+ RATE_54MBPS = 0x0C
+};
+
+enum {
+ RATE_INDEX_1MBPS = 0,
+ RATE_INDEX_2MBPS = 1,
+ RATE_INDEX_5_5MBPS = 2,
+ RATE_INDEX_6MBPS = 3,
+ RATE_INDEX_9MBPS = 4,
+ RATE_INDEX_11MBPS = 5,
+ RATE_INDEX_12MBPS = 6,
+ RATE_INDEX_18MBPS = 7,
+ RATE_INDEX_22MBPS = 8,
+ RATE_INDEX_24MBPS = 9,
+ RATE_INDEX_36MBPS = 10,
+ RATE_INDEX_48MBPS = 11,
+ RATE_INDEX_54MBPS = 12,
+ RATE_INDEX_MAX = RATE_INDEX_54MBPS,
+ MAX_RATE_INDEX,
+ INVALID_RATE_INDEX = MAX_RATE_INDEX,
+ RATE_INDEX_ENUM_MAX_SIZE = 0x7FFFFFFF
+};
+
+enum {
+ RATE_MASK_1MBPS = 0x1,
+ RATE_MASK_2MBPS = 0x2,
+ RATE_MASK_5_5MBPS = 0x4,
+ RATE_MASK_11MBPS = 0x20,
+};
+
+#define SHORT_PREAMBLE_BIT BIT(0) /* CCK or Barker depending on the rate */
+#define OFDM_RATE_BIT BIT(6)
+#define PBCC_RATE_BIT BIT(7)
+
+enum {
+ CCK_LONG = 0,
+ CCK_SHORT = SHORT_PREAMBLE_BIT,
+ PBCC_LONG = PBCC_RATE_BIT,
+ PBCC_SHORT = PBCC_RATE_BIT | SHORT_PREAMBLE_BIT,
+ OFDM = OFDM_RATE_BIT
+};
+
+/******************************************************************************
+
+Transmit-Descriptor RATE-SET field definitions...
+
+Define a new "Rate-Set" for TX path that incorporates the
+Rate & Modulation info into a single 16-bit field.
+
+TxdRateSet_t:
+b15 - Indicates Preamble type (1=SHORT, 0=LONG).
+ Notes:
+ Must be LONG (0) for 1Mbps rate.
+ Does not apply (set to 0) for RevG-OFDM rates.
+b14 - Indicates PBCC encoding (1=PBCC, 0=not).
+ Notes:
+ Does not apply (set to 0) for rates 1 and 2 Mbps.
+ Does not apply (set to 0) for RevG-OFDM rates.
+b13 - Unused (set to 0).
+b12-b0 - Supported Rate indicator bits as defined below.
+
+******************************************************************************/
+
+
+/*************************************************************************
+
+ Interrupt Trigger Register (Host -> WiLink)
+
+**************************************************************************/
+
+/* Hardware to Embedded CPU Interrupts - first 32-bit register set */
+
+/*
+ * Host Command Interrupt. Setting this bit masks
+ * the interrupt that the host issues to inform
+ * the FW that it has sent a command
+ * to the Wlan hardware Command Mailbox.
+ */
+#define INTR_TRIG_CMD BIT(0)
+
+/*
+ * Host Event Acknowlegde Interrupt. The host
+ * sets this bit to acknowledge that it received
+ * the unsolicited information from the event
+ * mailbox.
+ */
+#define INTR_TRIG_EVENT_ACK BIT(1)
+
+/*
+ * The host sets this bit to inform the Wlan
+ * FW that a TX packet is in the XFER
+ * Buffer #0.
+ */
+#define INTR_TRIG_TX_PROC0 BIT(2)
+
+/*
+ * The host sets this bit to inform the FW
+ * that it read a packet from RX XFER
+ * Buffer #0.
+ */
+#define INTR_TRIG_RX_PROC0 BIT(3)
+
+#define INTR_TRIG_DEBUG_ACK BIT(4)
+
+#define INTR_TRIG_STATE_CHANGED BIT(5)
+
+
+/* Hardware to Embedded CPU Interrupts - second 32-bit register set */
+
+/*
+ * The host sets this bit to inform the FW
+ * that it read a packet from RX XFER
+ * Buffer #1.
+ */
+#define INTR_TRIG_RX_PROC1 BIT(17)
+
+/*
+ * The host sets this bit to inform the Wlan
+ * hardware that a TX packet is in the XFER
+ * Buffer #1.
+ */
+#define INTR_TRIG_TX_PROC1 BIT(18)
+
+#endif