diff options
Diffstat (limited to 'drivers/net/wireless/ti/wl18xx/reg.h')
| -rw-r--r-- | drivers/net/wireless/ti/wl18xx/reg.h | 235 |
1 files changed, 235 insertions, 0 deletions
diff --git a/drivers/net/wireless/ti/wl18xx/reg.h b/drivers/net/wireless/ti/wl18xx/reg.h new file mode 100644 index 000000000..2f70dbdae --- /dev/null +++ b/drivers/net/wireless/ti/wl18xx/reg.h @@ -0,0 +1,235 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * This file is part of wlcore + * + * Copyright (C) 2011 Texas Instruments Inc. + */ + +#ifndef __REG_H__ +#define __REG_H__ + +#define WL18XX_REGISTERS_BASE 0x00800000 +#define WL18XX_CODE_BASE 0x00000000 +#define WL18XX_DATA_BASE 0x00400000 +#define WL18XX_DOUBLE_BUFFER_BASE 0x00600000 +#define WL18XX_MCU_KEY_SEARCH_BASE 0x00700000 +#define WL18XX_PHY_BASE 0x00900000 +#define WL18XX_TOP_OCP_BASE 0x00A00000 +#define WL18XX_PACKET_RAM_BASE 0x00B00000 +#define WL18XX_HOST_BASE 0x00C00000 + +#define WL18XX_REGISTERS_DOWN_SIZE 0x0000B000 + +#define WL18XX_REG_BOOT_PART_START 0x00802000 +#define WL18XX_REG_BOOT_PART_SIZE 0x00014578 + +#define WL18XX_PHY_INIT_MEM_ADDR 0x80926000 +#define WL18XX_PHY_END_MEM_ADDR 0x8093CA44 +#define WL18XX_PHY_INIT_MEM_SIZE \ + (WL18XX_PHY_END_MEM_ADDR - WL18XX_PHY_INIT_MEM_ADDR) + +#define WL18XX_SDIO_WSPI_BASE (WL18XX_REGISTERS_BASE) +#define WL18XX_REG_CONFIG_BASE (WL18XX_REGISTERS_BASE + 0x02000) +#define WL18XX_WGCM_REGS_BASE (WL18XX_REGISTERS_BASE + 0x03000) +#define WL18XX_ENC_BASE (WL18XX_REGISTERS_BASE + 0x04000) +#define WL18XX_INTERRUPT_BASE (WL18XX_REGISTERS_BASE + 0x05000) +#define WL18XX_UART_BASE (WL18XX_REGISTERS_BASE + 0x06000) +#define WL18XX_WELP_BASE (WL18XX_REGISTERS_BASE + 0x07000) +#define WL18XX_TCP_CKSM_BASE (WL18XX_REGISTERS_BASE + 0x08000) +#define WL18XX_FIFO_BASE (WL18XX_REGISTERS_BASE + 0x09000) +#define WL18XX_OCP_BRIDGE_BASE (WL18XX_REGISTERS_BASE + 0x0A000) +#define WL18XX_PMAC_RX_BASE (WL18XX_REGISTERS_BASE + 0x14800) +#define WL18XX_PMAC_ACM_BASE (WL18XX_REGISTERS_BASE + 0x14C00) +#define WL18XX_PMAC_TX_BASE (WL18XX_REGISTERS_BASE + 0x15000) +#define WL18XX_PMAC_CSR_BASE (WL18XX_REGISTERS_BASE + 0x15400) + +#define WL18XX_REG_ECPU_CONTROL (WL18XX_REGISTERS_BASE + 0x02004) +#define WL18XX_REG_INTERRUPT_NO_CLEAR (WL18XX_REGISTERS_BASE + 0x050E8) +#define WL18XX_REG_INTERRUPT_ACK (WL18XX_REGISTERS_BASE + 0x050F0) +#define WL18XX_REG_INTERRUPT_TRIG (WL18XX_REGISTERS_BASE + 0x5074) +#define WL18XX_REG_INTERRUPT_TRIG_H (WL18XX_REGISTERS_BASE + 0x5078) +#define WL18XX_REG_INTERRUPT_MASK (WL18XX_REGISTERS_BASE + 0x0050DC) + +#define WL18XX_REG_CHIP_ID_B (WL18XX_REGISTERS_BASE + 0x01542C) + +#define WL18XX_SLV_MEM_DATA (WL18XX_HOST_BASE + 0x0018) +#define WL18XX_SLV_REG_DATA (WL18XX_HOST_BASE + 0x0008) + +/* Scratch Pad registers*/ +#define WL18XX_SCR_PAD0 (WL18XX_REGISTERS_BASE + 0x0154EC) +#define WL18XX_SCR_PAD1 (WL18XX_REGISTERS_BASE + 0x0154F0) +#define WL18XX_SCR_PAD2 (WL18XX_REGISTERS_BASE + 0x0154F4) +#define WL18XX_SCR_PAD3 (WL18XX_REGISTERS_BASE + 0x0154F8) +#define WL18XX_SCR_PAD4 (WL18XX_REGISTERS_BASE + 0x0154FC) +#define WL18XX_SCR_PAD4_SET (WL18XX_REGISTERS_BASE + 0x015504) +#define WL18XX_SCR_PAD4_CLR (WL18XX_REGISTERS_BASE + 0x015500) +#define WL18XX_SCR_PAD5 (WL18XX_REGISTERS_BASE + 0x015508) +#define WL18XX_SCR_PAD5_SET (WL18XX_REGISTERS_BASE + 0x015510) +#define WL18XX_SCR_PAD5_CLR (WL18XX_REGISTERS_BASE + 0x01550C) +#define WL18XX_SCR_PAD6 (WL18XX_REGISTERS_BASE + 0x015514) +#define WL18XX_SCR_PAD7 (WL18XX_REGISTERS_BASE + 0x015518) +#define WL18XX_SCR_PAD8 (WL18XX_REGISTERS_BASE + 0x01551C) +#define WL18XX_SCR_PAD9 (WL18XX_REGISTERS_BASE + 0x015520) + +/* Spare registers*/ +#define WL18XX_SPARE_A1 (WL18XX_REGISTERS_BASE + 0x002194) +#define WL18XX_SPARE_A2 (WL18XX_REGISTERS_BASE + 0x002198) +#define WL18XX_SPARE_A3 (WL18XX_REGISTERS_BASE + 0x00219C) +#define WL18XX_SPARE_A4 (WL18XX_REGISTERS_BASE + 0x0021A0) +#define WL18XX_SPARE_A5 (WL18XX_REGISTERS_BASE + 0x0021A4) +#define WL18XX_SPARE_A6 (WL18XX_REGISTERS_BASE + 0x0021A8) +#define WL18XX_SPARE_A7 (WL18XX_REGISTERS_BASE + 0x0021AC) +#define WL18XX_SPARE_A8 (WL18XX_REGISTERS_BASE + 0x0021B0) +#define WL18XX_SPARE_B1 (WL18XX_REGISTERS_BASE + 0x015524) +#define WL18XX_SPARE_B2 (WL18XX_REGISTERS_BASE + 0x015528) +#define WL18XX_SPARE_B3 (WL18XX_REGISTERS_BASE + 0x01552C) +#define WL18XX_SPARE_B4 (WL18XX_REGISTERS_BASE + 0x015530) +#define WL18XX_SPARE_B5 (WL18XX_REGISTERS_BASE + 0x015534) +#define WL18XX_SPARE_B6 (WL18XX_REGISTERS_BASE + 0x015538) +#define WL18XX_SPARE_B7 (WL18XX_REGISTERS_BASE + 0x01553C) +#define WL18XX_SPARE_B8 (WL18XX_REGISTERS_BASE + 0x015540) + +#define WL18XX_REG_COMMAND_MAILBOX_PTR (WL18XX_SCR_PAD0) +#define WL18XX_REG_EVENT_MAILBOX_PTR (WL18XX_SCR_PAD1) +#define WL18XX_EEPROMLESS_IND (WL18XX_SCR_PAD4) + +#define WL18XX_WELP_ARM_COMMAND (WL18XX_REGISTERS_BASE + 0x7100) +#define WL18XX_ENABLE (WL18XX_REGISTERS_BASE + 0x01543C) +#define TOP_FN0_CCCR_REG_32 (WL18XX_TOP_OCP_BASE + 0x64) + +/* PRCM registers */ +#define PLATFORM_DETECTION 0xA0E3E0 +#define OCS_EN 0xA02080 +#define PRIMARY_CLK_DETECT 0xA020A6 +#define PLLSH_COEX_PLL_N 0xA02384 +#define PLLSH_COEX_PLL_M 0xA02382 +#define PLLSH_COEX_PLL_SWALLOW_EN 0xA0238E +#define PLLSH_WL_PLL_SEL 0xA02398 + +#define PLLSH_WCS_PLL_N 0xA02362 +#define PLLSH_WCS_PLL_M 0xA02360 +#define PLLSH_WCS_PLL_Q_FACTOR_CFG_1 0xA02364 +#define PLLSH_WCS_PLL_Q_FACTOR_CFG_2 0xA02366 +#define PLLSH_WCS_PLL_P_FACTOR_CFG_1 0xA02368 +#define PLLSH_WCS_PLL_P_FACTOR_CFG_2 0xA0236A +#define PLLSH_WCS_PLL_SWALLOW_EN 0xA0236C +#define PLLSH_WL_PLL_EN 0xA02392 + +#define PLLSH_WCS_PLL_Q_FACTOR_CFG_1_MASK 0xFFFF +#define PLLSH_WCS_PLL_Q_FACTOR_CFG_2_MASK 0x007F +#define PLLSH_WCS_PLL_P_FACTOR_CFG_1_MASK 0xFFFF +#define PLLSH_WCS_PLL_P_FACTOR_CFG_2_MASK 0x000F + +#define PLLSH_WL_PLL_EN_VAL1 0x7 +#define PLLSH_WL_PLL_EN_VAL2 0x2 +#define PLLSH_COEX_PLL_SWALLOW_EN_VAL1 0x2 +#define PLLSH_COEX_PLL_SWALLOW_EN_VAL2 0x11 + +#define PLLSH_WCS_PLL_SWALLOW_EN_VAL1 0x1 +#define PLLSH_WCS_PLL_SWALLOW_EN_VAL2 0x12 + +#define PLLSH_WL_PLL_SEL_WCS_PLL 0x0 +#define PLLSH_WL_PLL_SEL_COEX_PLL 0x1 + +#define WL18XX_REG_FUSE_DATA_1_3 0xA0260C +#define WL18XX_PG_VER_MASK 0x70 +#define WL18XX_PG_VER_OFFSET 4 +#define WL18XX_ROM_VER_MASK 0x3e00 +#define WL18XX_ROM_VER_OFFSET 9 +#define WL18XX_METAL_VER_MASK 0xC +#define WL18XX_METAL_VER_OFFSET 2 +#define WL18XX_NEW_METAL_VER_MASK 0x180 +#define WL18XX_NEW_METAL_VER_OFFSET 7 + +#define WL18XX_PACKAGE_TYPE_OFFSET 13 +#define WL18XX_PACKAGE_TYPE_WSP 0 + +#define WL18XX_REG_FUSE_DATA_2_3 0xA02614 +#define WL18XX_RDL_VER_MASK 0x1f00 +#define WL18XX_RDL_VER_OFFSET 8 + +#define WL18XX_REG_FUSE_BD_ADDR_1 0xA02602 +#define WL18XX_REG_FUSE_BD_ADDR_2 0xA02606 + +#define WL18XX_CMD_MBOX_ADDRESS 0xB007B4 + +#define WL18XX_FW_STATUS_ADDR 0x50F8 + +#define CHIP_ID_185x_PG10 (0x06030101) +#define CHIP_ID_185x_PG20 (0x06030111) + +/* + * Host Command Interrupt. Setting this bit masks + * the interrupt that the host issues to inform + * the FW that it has sent a command + * to the Wlan hardware Command Mailbox. + */ +#define WL18XX_INTR_TRIG_CMD BIT(28) + +/* + * Host Event Acknowlegde Interrupt. The host + * sets this bit to acknowledge that it received + * the unsolicited information from the event + * mailbox. + */ +#define WL18XX_INTR_TRIG_EVENT_ACK BIT(29) + +/* + * To boot the firmware in PLT mode we need to write this value in + * SCR_PAD8 before starting. + */ +#define WL18XX_SCR_PAD8_PLT 0xBABABEBE + +enum { + COMPONENT_NO_SWITCH = 0x0, + COMPONENT_2_WAY_SWITCH = 0x1, + COMPONENT_3_WAY_SWITCH = 0x2, + COMPONENT_MATCHING = 0x3, +}; + +enum { + FEM_NONE = 0x0, + FEM_VENDOR_1 = 0x1, + FEM_VENDOR_2 = 0x2, + FEM_VENDOR_3 = 0x3, +}; + +enum { + BOARD_TYPE_EVB_18XX = 0, + BOARD_TYPE_DVP_18XX = 1, + BOARD_TYPE_HDK_18XX = 2, + BOARD_TYPE_FPGA_18XX = 3, + BOARD_TYPE_COM8_18XX = 4, + + NUM_BOARD_TYPES, +}; + +enum wl18xx_rdl_num { + RDL_NONE = 0, + RDL_1_HP = 1, + RDL_2_SP = 2, + RDL_3_HP = 3, + RDL_4_SP = 4, + RDL_5_SP = 0x11, + RDL_6_SP = 0x12, + RDL_7_SP = 0x13, + RDL_8_SP = 0x14, + + _RDL_LAST, + RDL_MAX = _RDL_LAST - 1, +}; + + +/* FPGA_SPARE_1 register - used to change the PHY ATPG clock at boot time */ +#define WL18XX_PHY_FPGA_SPARE_1 0x8093CA40 + +/* command to disable FDSP clock */ +#define MEM_FDSP_CLK_120_DISABLE 0x80000000 + +/* command to set ATPG clock toward FDSP Code RAM rather than its own clock */ +#define MEM_FDSP_CODERAM_FUNC_CLK_SEL 0xC0000000 + +/* command to re-enable FDSP clock */ +#define MEM_FDSP_CLK_120_ENABLE 0x40000000 + +#endif /* __REG_H__ */ |