diff options
Diffstat (limited to 'drivers/pinctrl/pinctrl-cy8c95x0.c')
| -rw-r--r-- | drivers/pinctrl/pinctrl-cy8c95x0.c | 1421 |
1 files changed, 1421 insertions, 0 deletions
diff --git a/drivers/pinctrl/pinctrl-cy8c95x0.c b/drivers/pinctrl/pinctrl-cy8c95x0.c new file mode 100644 index 000000000..5abab6bc7 --- /dev/null +++ b/drivers/pinctrl/pinctrl-cy8c95x0.c @@ -0,0 +1,1421 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * CY8C95X0 20/40/60 pin I2C GPIO port expander with interrupt support + * + * Copyright (C) 2022 9elements GmbH + * Authors: Patrick Rudolph <patrick.rudolph@9elements.com> + * Naresh Solanki <Naresh.Solanki@9elements.com> + */ + +#include <linux/acpi.h> +#include <linux/bitmap.h> +#include <linux/dmi.h> +#include <linux/gpio/driver.h> +#include <linux/gpio/consumer.h> +#include <linux/i2c.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/mod_devicetable.h> +#include <linux/module.h> +#include <linux/property.h> +#include <linux/regmap.h> +#include <linux/regulator/consumer.h> + +#include <linux/pinctrl/pinctrl.h> +#include <linux/pinctrl/pinconf.h> +#include <linux/pinctrl/pinconf-generic.h> +#include <linux/pinctrl/pinmux.h> + +/* Fast access registers */ +#define CY8C95X0_INPUT 0x00 +#define CY8C95X0_OUTPUT 0x08 +#define CY8C95X0_INTSTATUS 0x10 + +#define CY8C95X0_INPUT_(x) (CY8C95X0_INPUT + (x)) +#define CY8C95X0_OUTPUT_(x) (CY8C95X0_OUTPUT + (x)) +#define CY8C95X0_INTSTATUS_(x) (CY8C95X0_INTSTATUS + (x)) + +/* Port Select configures the port */ +#define CY8C95X0_PORTSEL 0x18 +/* Port settings, write PORTSEL first */ +#define CY8C95X0_INTMASK 0x19 +#define CY8C95X0_PWMSEL 0x1A +#define CY8C95X0_INVERT 0x1B +#define CY8C95X0_DIRECTION 0x1C +/* Drive mode register change state on writing '1' */ +#define CY8C95X0_DRV_PU 0x1D +#define CY8C95X0_DRV_PD 0x1E +#define CY8C95X0_DRV_ODH 0x1F +#define CY8C95X0_DRV_ODL 0x20 +#define CY8C95X0_DRV_PP_FAST 0x21 +#define CY8C95X0_DRV_PP_SLOW 0x22 +#define CY8C95X0_DRV_HIZ 0x23 +#define CY8C95X0_DEVID 0x2E +#define CY8C95X0_WATCHDOG 0x2F +#define CY8C95X0_COMMAND 0x30 + +#define CY8C95X0_PIN_TO_OFFSET(x) (((x) >= 20) ? ((x) + 4) : (x)) + +static const struct i2c_device_id cy8c95x0_id[] = { + { "cy8c9520", 20, }, + { "cy8c9540", 40, }, + { "cy8c9560", 60, }, + { } +}; +MODULE_DEVICE_TABLE(i2c, cy8c95x0_id); + +#define OF_CY8C95X(__nrgpio) ((void *)(__nrgpio)) + +static const struct of_device_id cy8c95x0_dt_ids[] = { + { .compatible = "cypress,cy8c9520", .data = OF_CY8C95X(20), }, + { .compatible = "cypress,cy8c9540", .data = OF_CY8C95X(40), }, + { .compatible = "cypress,cy8c9560", .data = OF_CY8C95X(60), }, + { } +}; +MODULE_DEVICE_TABLE(of, cy8c95x0_dt_ids); + +static const struct acpi_gpio_params cy8c95x0_irq_gpios = { 0, 0, true }; + +static const struct acpi_gpio_mapping cy8c95x0_acpi_irq_gpios[] = { + { "irq-gpios", &cy8c95x0_irq_gpios, 1, ACPI_GPIO_QUIRK_ABSOLUTE_NUMBER }, + { } +}; + +static int cy8c95x0_acpi_get_irq(struct device *dev) +{ + int ret; + + ret = devm_acpi_dev_add_driver_gpios(dev, cy8c95x0_acpi_irq_gpios); + if (ret) + dev_warn(dev, "can't add GPIO ACPI mapping\n"); + + ret = acpi_dev_gpio_irq_get_by(ACPI_COMPANION(dev), "irq-gpios", 0); + if (ret < 0) + return ret; + + dev_info(dev, "ACPI interrupt quirk (IRQ %d)\n", ret); + return ret; +} + +static const struct dmi_system_id cy8c95x0_dmi_acpi_irq_info[] = { + { + /* + * On Intel Galileo Gen 1 board the IRQ pin is provided + * as an absolute number instead of being relative. + * Since first controller (gpio-sch.c) and second + * (gpio-dwapb.c) are at the fixed bases, we may safely + * refer to the number in the global space to get an IRQ + * out of it. + */ + .matches = { + DMI_EXACT_MATCH(DMI_BOARD_NAME, "Galileo"), + }, + }, + {} +}; + +#define MAX_BANK 8 +#define BANK_SZ 8 +#define MAX_LINE (MAX_BANK * BANK_SZ) + +#define CY8C95X0_GPIO_MASK GENMASK(7, 0) + +/** + * struct cy8c95x0_pinctrl - driver data + * @regmap: Device's regmap + * @irq_lock: IRQ bus lock + * @i2c_lock: Mutex for the device internal mux register + * @irq_mask: I/O bits affected by interrupts + * @irq_trig_raise: I/O bits affected by raising voltage level + * @irq_trig_fall: I/O bits affected by falling voltage level + * @irq_trig_low: I/O bits affected by a low voltage level + * @irq_trig_high: I/O bits affected by a high voltage level + * @push_pull: I/O bits configured as push pull driver + * @shiftmask: Mask used to compensate for Gport2 width + * @nport: Number of Gports in this chip + * @gpio_chip: gpiolib chip + * @driver_data: private driver data + * @regulator: Pointer to the regulator for the IC + * @dev: struct device + * @pctldev: pin controller device + * @pinctrl_desc: pin controller description + * @name: Chip controller name + * @tpin: Total number of pins + */ +struct cy8c95x0_pinctrl { + struct regmap *regmap; + struct mutex irq_lock; + struct mutex i2c_lock; + DECLARE_BITMAP(irq_mask, MAX_LINE); + DECLARE_BITMAP(irq_trig_raise, MAX_LINE); + DECLARE_BITMAP(irq_trig_fall, MAX_LINE); + DECLARE_BITMAP(irq_trig_low, MAX_LINE); + DECLARE_BITMAP(irq_trig_high, MAX_LINE); + DECLARE_BITMAP(push_pull, MAX_LINE); + DECLARE_BITMAP(shiftmask, MAX_LINE); + int nport; + struct gpio_chip gpio_chip; + unsigned long driver_data; + struct regulator *regulator; + struct device *dev; + struct pinctrl_dev *pctldev; + struct pinctrl_desc pinctrl_desc; + char name[32]; + unsigned int tpin; +}; + +static const struct pinctrl_pin_desc cy8c9560_pins[] = { + PINCTRL_PIN(0, "gp00"), + PINCTRL_PIN(1, "gp01"), + PINCTRL_PIN(2, "gp02"), + PINCTRL_PIN(3, "gp03"), + PINCTRL_PIN(4, "gp04"), + PINCTRL_PIN(5, "gp05"), + PINCTRL_PIN(6, "gp06"), + PINCTRL_PIN(7, "gp07"), + + PINCTRL_PIN(8, "gp10"), + PINCTRL_PIN(9, "gp11"), + PINCTRL_PIN(10, "gp12"), + PINCTRL_PIN(11, "gp13"), + PINCTRL_PIN(12, "gp14"), + PINCTRL_PIN(13, "gp15"), + PINCTRL_PIN(14, "gp16"), + PINCTRL_PIN(15, "gp17"), + + PINCTRL_PIN(16, "gp20"), + PINCTRL_PIN(17, "gp21"), + PINCTRL_PIN(18, "gp22"), + PINCTRL_PIN(19, "gp23"), + + PINCTRL_PIN(20, "gp30"), + PINCTRL_PIN(21, "gp31"), + PINCTRL_PIN(22, "gp32"), + PINCTRL_PIN(23, "gp33"), + PINCTRL_PIN(24, "gp34"), + PINCTRL_PIN(25, "gp35"), + PINCTRL_PIN(26, "gp36"), + PINCTRL_PIN(27, "gp37"), + + PINCTRL_PIN(28, "gp40"), + PINCTRL_PIN(29, "gp41"), + PINCTRL_PIN(30, "gp42"), + PINCTRL_PIN(31, "gp43"), + PINCTRL_PIN(32, "gp44"), + PINCTRL_PIN(33, "gp45"), + PINCTRL_PIN(34, "gp46"), + PINCTRL_PIN(35, "gp47"), + + PINCTRL_PIN(36, "gp50"), + PINCTRL_PIN(37, "gp51"), + PINCTRL_PIN(38, "gp52"), + PINCTRL_PIN(39, "gp53"), + PINCTRL_PIN(40, "gp54"), + PINCTRL_PIN(41, "gp55"), + PINCTRL_PIN(42, "gp56"), + PINCTRL_PIN(43, "gp57"), + + PINCTRL_PIN(44, "gp60"), + PINCTRL_PIN(45, "gp61"), + PINCTRL_PIN(46, "gp62"), + PINCTRL_PIN(47, "gp63"), + PINCTRL_PIN(48, "gp64"), + PINCTRL_PIN(49, "gp65"), + PINCTRL_PIN(50, "gp66"), + PINCTRL_PIN(51, "gp67"), + + PINCTRL_PIN(52, "gp70"), + PINCTRL_PIN(53, "gp71"), + PINCTRL_PIN(54, "gp72"), + PINCTRL_PIN(55, "gp73"), + PINCTRL_PIN(56, "gp74"), + PINCTRL_PIN(57, "gp75"), + PINCTRL_PIN(58, "gp76"), + PINCTRL_PIN(59, "gp77"), +}; + +static const char * const cy8c95x0_groups[] = { + "gp00", + "gp01", + "gp02", + "gp03", + "gp04", + "gp05", + "gp06", + "gp07", + + "gp10", + "gp11", + "gp12", + "gp13", + "gp14", + "gp15", + "gp16", + "gp17", + + "gp20", + "gp21", + "gp22", + "gp23", + + "gp30", + "gp31", + "gp32", + "gp33", + "gp34", + "gp35", + "gp36", + "gp37", + + "gp40", + "gp41", + "gp42", + "gp43", + "gp44", + "gp45", + "gp46", + "gp47", + + "gp50", + "gp51", + "gp52", + "gp53", + "gp54", + "gp55", + "gp56", + "gp57", + + "gp60", + "gp61", + "gp62", + "gp63", + "gp64", + "gp65", + "gp66", + "gp67", + + "gp70", + "gp71", + "gp72", + "gp73", + "gp74", + "gp75", + "gp76", + "gp77", +}; + +static inline u8 cypress_get_port(struct cy8c95x0_pinctrl *chip, unsigned int pin) +{ + /* Account for GPORT2 which only has 4 bits */ + return CY8C95X0_PIN_TO_OFFSET(pin) / BANK_SZ; +} + +static int cypress_get_pin_mask(struct cy8c95x0_pinctrl *chip, unsigned int pin) +{ + /* Account for GPORT2 which only has 4 bits */ + return BIT(CY8C95X0_PIN_TO_OFFSET(pin) % BANK_SZ); +} + +static bool cy8c95x0_readable_register(struct device *dev, unsigned int reg) +{ + switch (reg) { + case 0x24 ... 0x27: + return false; + default: + return true; + } +} + +static bool cy8c95x0_writeable_register(struct device *dev, unsigned int reg) +{ + switch (reg) { + case CY8C95X0_INPUT_(0) ... CY8C95X0_INPUT_(7): + return false; + case CY8C95X0_DEVID: + return false; + case 0x24 ... 0x27: + return false; + default: + return true; + } +} + +static bool cy8c95x0_volatile_register(struct device *dev, unsigned int reg) +{ + switch (reg) { + case CY8C95X0_INPUT_(0) ... CY8C95X0_INPUT_(7): + case CY8C95X0_INTSTATUS_(0) ... CY8C95X0_INTSTATUS_(7): + case CY8C95X0_INTMASK: + case CY8C95X0_INVERT: + case CY8C95X0_PWMSEL: + case CY8C95X0_DIRECTION: + case CY8C95X0_DRV_PU: + case CY8C95X0_DRV_PD: + case CY8C95X0_DRV_ODH: + case CY8C95X0_DRV_ODL: + case CY8C95X0_DRV_PP_FAST: + case CY8C95X0_DRV_PP_SLOW: + case CY8C95X0_DRV_HIZ: + return true; + default: + return false; + } +} + +static bool cy8c95x0_precious_register(struct device *dev, unsigned int reg) +{ + switch (reg) { + case CY8C95X0_INTSTATUS_(0) ... CY8C95X0_INTSTATUS_(7): + return true; + default: + return false; + } +} + +static const struct reg_default cy8c95x0_reg_defaults[] = { + { CY8C95X0_OUTPUT_(0), GENMASK(7, 0) }, + { CY8C95X0_OUTPUT_(1), GENMASK(7, 0) }, + { CY8C95X0_OUTPUT_(2), GENMASK(7, 0) }, + { CY8C95X0_OUTPUT_(3), GENMASK(7, 0) }, + { CY8C95X0_OUTPUT_(4), GENMASK(7, 0) }, + { CY8C95X0_OUTPUT_(5), GENMASK(7, 0) }, + { CY8C95X0_OUTPUT_(6), GENMASK(7, 0) }, + { CY8C95X0_OUTPUT_(7), GENMASK(7, 0) }, + { CY8C95X0_PORTSEL, 0 }, + { CY8C95X0_PWMSEL, 0 }, +}; + +static const struct regmap_config cy8c95x0_i2c_regmap = { + .reg_bits = 8, + .val_bits = 8, + + .reg_defaults = cy8c95x0_reg_defaults, + .num_reg_defaults = ARRAY_SIZE(cy8c95x0_reg_defaults), + + .readable_reg = cy8c95x0_readable_register, + .writeable_reg = cy8c95x0_writeable_register, + .volatile_reg = cy8c95x0_volatile_register, + .precious_reg = cy8c95x0_precious_register, + + .cache_type = REGCACHE_FLAT, + .max_register = CY8C95X0_COMMAND, +}; + +static int cy8c95x0_write_regs_mask(struct cy8c95x0_pinctrl *chip, int reg, + unsigned long *val, unsigned long *mask) +{ + DECLARE_BITMAP(tmask, MAX_LINE); + DECLARE_BITMAP(tval, MAX_LINE); + int write_val; + int ret = 0; + int i, off = 0; + u8 bits; + + /* Add the 4 bit gap of Gport2 */ + bitmap_andnot(tmask, mask, chip->shiftmask, MAX_LINE); + bitmap_shift_left(tmask, tmask, 4, MAX_LINE); + bitmap_replace(tmask, tmask, mask, chip->shiftmask, BANK_SZ * 3); + + bitmap_andnot(tval, val, chip->shiftmask, MAX_LINE); + bitmap_shift_left(tval, tval, 4, MAX_LINE); + bitmap_replace(tval, tval, val, chip->shiftmask, BANK_SZ * 3); + + mutex_lock(&chip->i2c_lock); + for (i = 0; i < chip->nport; i++) { + /* Skip over unused banks */ + bits = bitmap_get_value8(tmask, i * BANK_SZ); + if (!bits) + continue; + + switch (reg) { + /* Muxed registers */ + case CY8C95X0_INTMASK: + case CY8C95X0_PWMSEL: + case CY8C95X0_INVERT: + case CY8C95X0_DIRECTION: + case CY8C95X0_DRV_PU: + case CY8C95X0_DRV_PD: + case CY8C95X0_DRV_ODH: + case CY8C95X0_DRV_ODL: + case CY8C95X0_DRV_PP_FAST: + case CY8C95X0_DRV_PP_SLOW: + case CY8C95X0_DRV_HIZ: + ret = regmap_write(chip->regmap, CY8C95X0_PORTSEL, i); + if (ret < 0) + goto out; + off = reg; + break; + /* Direct access registers */ + case CY8C95X0_INPUT: + case CY8C95X0_OUTPUT: + case CY8C95X0_INTSTATUS: + off = reg + i; + break; + default: + ret = -EINVAL; + goto out; + } + + write_val = bitmap_get_value8(tval, i * BANK_SZ); + + ret = regmap_update_bits(chip->regmap, off, bits, write_val); + if (ret < 0) + goto out; + } +out: + mutex_unlock(&chip->i2c_lock); + + if (ret < 0) + dev_err(chip->dev, "failed writing register %d: err %d\n", off, ret); + + return ret; +} + +static int cy8c95x0_read_regs_mask(struct cy8c95x0_pinctrl *chip, int reg, + unsigned long *val, unsigned long *mask) +{ + DECLARE_BITMAP(tmask, MAX_LINE); + DECLARE_BITMAP(tval, MAX_LINE); + DECLARE_BITMAP(tmp, MAX_LINE); + int read_val; + int ret = 0; + int i, off = 0; + u8 bits; + + /* Add the 4 bit gap of Gport2 */ + bitmap_andnot(tmask, mask, chip->shiftmask, MAX_LINE); + bitmap_shift_left(tmask, tmask, 4, MAX_LINE); + bitmap_replace(tmask, tmask, mask, chip->shiftmask, BANK_SZ * 3); + + bitmap_andnot(tval, val, chip->shiftmask, MAX_LINE); + bitmap_shift_left(tval, tval, 4, MAX_LINE); + bitmap_replace(tval, tval, val, chip->shiftmask, BANK_SZ * 3); + + mutex_lock(&chip->i2c_lock); + for (i = 0; i < chip->nport; i++) { + /* Skip over unused banks */ + bits = bitmap_get_value8(tmask, i * BANK_SZ); + if (!bits) + continue; + + switch (reg) { + /* Muxed registers */ + case CY8C95X0_INTMASK: + case CY8C95X0_PWMSEL: + case CY8C95X0_INVERT: + case CY8C95X0_DIRECTION: + case CY8C95X0_DRV_PU: + case CY8C95X0_DRV_PD: + case CY8C95X0_DRV_ODH: + case CY8C95X0_DRV_ODL: + case CY8C95X0_DRV_PP_FAST: + case CY8C95X0_DRV_PP_SLOW: + case CY8C95X0_DRV_HIZ: + ret = regmap_write(chip->regmap, CY8C95X0_PORTSEL, i); + if (ret < 0) + goto out; + off = reg; + break; + /* Direct access registers */ + case CY8C95X0_INPUT: + case CY8C95X0_OUTPUT: + case CY8C95X0_INTSTATUS: + off = reg + i; + break; + default: + ret = -EINVAL; + goto out; + } + + ret = regmap_read(chip->regmap, off, &read_val); + if (ret < 0) + goto out; + + read_val &= bits; + read_val |= bitmap_get_value8(tval, i * BANK_SZ) & ~bits; + bitmap_set_value8(tval, read_val, i * BANK_SZ); + } + + /* Fill the 4 bit gap of Gport2 */ + bitmap_shift_right(tmp, tval, 4, MAX_LINE); + bitmap_replace(val, tmp, tval, chip->shiftmask, MAX_LINE); + +out: + mutex_unlock(&chip->i2c_lock); + + if (ret < 0) + dev_err(chip->dev, "failed reading register %d: err %d\n", off, ret); + + return ret; +} + +static int cy8c95x0_gpio_direction_input(struct gpio_chip *gc, unsigned int off) +{ + struct cy8c95x0_pinctrl *chip = gpiochip_get_data(gc); + u8 port = cypress_get_port(chip, off); + u8 bit = cypress_get_pin_mask(chip, off); + int ret; + + mutex_lock(&chip->i2c_lock); + ret = regmap_write(chip->regmap, CY8C95X0_PORTSEL, port); + if (ret) + goto out; + + ret = regmap_write_bits(chip->regmap, CY8C95X0_DIRECTION, bit, bit); + if (ret) + goto out; + + if (test_bit(off, chip->push_pull)) { + /* + * Disable driving the pin by forcing it to HighZ. Only setting the + * direction register isn't sufficient in Push-Pull mode. + */ + ret = regmap_write_bits(chip->regmap, CY8C95X0_DRV_HIZ, bit, bit); + if (ret) + goto out; + + __clear_bit(off, chip->push_pull); + } + +out: + mutex_unlock(&chip->i2c_lock); + + return ret; +} + +static int cy8c95x0_gpio_direction_output(struct gpio_chip *gc, + unsigned int off, int val) +{ + struct cy8c95x0_pinctrl *chip = gpiochip_get_data(gc); + u8 port = cypress_get_port(chip, off); + u8 outreg = CY8C95X0_OUTPUT_(port); + u8 bit = cypress_get_pin_mask(chip, off); + int ret; + + /* Set output level */ + ret = regmap_write_bits(chip->regmap, outreg, bit, val ? bit : 0); + if (ret) + return ret; + + mutex_lock(&chip->i2c_lock); + /* Select port... */ + ret = regmap_write(chip->regmap, CY8C95X0_PORTSEL, port); + if (ret) + goto out; + + /* ...then direction */ + ret = regmap_write_bits(chip->regmap, CY8C95X0_DIRECTION, bit, 0); + +out: + mutex_unlock(&chip->i2c_lock); + + return ret; +} + +static int cy8c95x0_gpio_get_value(struct gpio_chip *gc, unsigned int off) +{ + struct cy8c95x0_pinctrl *chip = gpiochip_get_data(gc); + u8 inreg = CY8C95X0_INPUT_(cypress_get_port(chip, off)); + u8 bit = cypress_get_pin_mask(chip, off); + u32 reg_val; + int ret; + + ret = regmap_read(chip->regmap, inreg, ®_val); + if (ret < 0) { + /* + * NOTE: + * Diagnostic already emitted; that's all we should + * do unless gpio_*_value_cansleep() calls become different + * from their nonsleeping siblings (and report faults). + */ + return 0; + } + + return !!(reg_val & bit); +} + +static void cy8c95x0_gpio_set_value(struct gpio_chip *gc, unsigned int off, + int val) +{ + struct cy8c95x0_pinctrl *chip = gpiochip_get_data(gc); + u8 outreg = CY8C95X0_OUTPUT_(cypress_get_port(chip, off)); + u8 bit = cypress_get_pin_mask(chip, off); + + regmap_write_bits(chip->regmap, outreg, bit, val ? bit : 0); +} + +static int cy8c95x0_gpio_get_direction(struct gpio_chip *gc, unsigned int off) +{ + struct cy8c95x0_pinctrl *chip = gpiochip_get_data(gc); + u8 port = cypress_get_port(chip, off); + u8 bit = cypress_get_pin_mask(chip, off); + u32 reg_val; + int ret; + + mutex_lock(&chip->i2c_lock); + + ret = regmap_write(chip->regmap, CY8C95X0_PORTSEL, port); + if (ret < 0) + goto out; + + ret = regmap_read(chip->regmap, CY8C95X0_DIRECTION, ®_val); + if (ret < 0) + goto out; + + mutex_unlock(&chip->i2c_lock); + + if (reg_val & bit) + return GPIO_LINE_DIRECTION_IN; + + return GPIO_LINE_DIRECTION_OUT; +out: + mutex_unlock(&chip->i2c_lock); + return ret; +} + +static int cy8c95x0_gpio_get_pincfg(struct cy8c95x0_pinctrl *chip, + unsigned int off, + unsigned long *config) +{ + enum pin_config_param param = pinconf_to_config_param(*config); + u8 port = cypress_get_port(chip, off); + u8 bit = cypress_get_pin_mask(chip, off); + unsigned int reg; + u32 reg_val; + u16 arg = 0; + int ret; + + mutex_lock(&chip->i2c_lock); + + /* Select port */ + ret = regmap_write(chip->regmap, CY8C95X0_PORTSEL, port); + if (ret < 0) + goto out; + + switch (param) { + case PIN_CONFIG_BIAS_PULL_UP: + reg = CY8C95X0_DRV_PU; + break; + case PIN_CONFIG_BIAS_PULL_DOWN: + reg = CY8C95X0_DRV_PD; + break; + case PIN_CONFIG_BIAS_DISABLE: + reg = CY8C95X0_DRV_HIZ; + break; + case PIN_CONFIG_DRIVE_OPEN_DRAIN: + reg = CY8C95X0_DRV_ODL; + break; + case PIN_CONFIG_DRIVE_OPEN_SOURCE: + reg = CY8C95X0_DRV_ODH; + break; + case PIN_CONFIG_DRIVE_PUSH_PULL: + reg = CY8C95X0_DRV_PP_FAST; + break; + case PIN_CONFIG_INPUT_ENABLE: + reg = CY8C95X0_DIRECTION; + break; + case PIN_CONFIG_MODE_PWM: + reg = CY8C95X0_PWMSEL; + break; + case PIN_CONFIG_OUTPUT: + reg = CY8C95X0_OUTPUT_(port); + break; + case PIN_CONFIG_OUTPUT_ENABLE: + reg = CY8C95X0_DIRECTION; + break; + + case PIN_CONFIG_BIAS_HIGH_IMPEDANCE: + case PIN_CONFIG_BIAS_BUS_HOLD: + case PIN_CONFIG_BIAS_PULL_PIN_DEFAULT: + case PIN_CONFIG_DRIVE_STRENGTH: + case PIN_CONFIG_DRIVE_STRENGTH_UA: + case PIN_CONFIG_INPUT_DEBOUNCE: + case PIN_CONFIG_INPUT_SCHMITT: + case PIN_CONFIG_INPUT_SCHMITT_ENABLE: + case PIN_CONFIG_MODE_LOW_POWER: + case PIN_CONFIG_PERSIST_STATE: + case PIN_CONFIG_POWER_SOURCE: + case PIN_CONFIG_SKEW_DELAY: + case PIN_CONFIG_SLEEP_HARDWARE_STATE: + case PIN_CONFIG_SLEW_RATE: + default: + ret = -ENOTSUPP; + goto out; + } + /* + * Writing 1 to one of the drive mode registers will automatically + * clear conflicting set bits in the other drive mode registers. + */ + ret = regmap_read(chip->regmap, reg, ®_val); + if (reg_val & bit) + arg = 1; + if (param == PIN_CONFIG_OUTPUT_ENABLE) + arg = !arg; + + *config = pinconf_to_config_packed(param, (u16)arg); +out: + mutex_unlock(&chip->i2c_lock); + + return ret; +} + +static int cy8c95x0_gpio_set_pincfg(struct cy8c95x0_pinctrl *chip, + unsigned int off, + unsigned long config) +{ + u8 port = cypress_get_port(chip, off); + u8 bit = cypress_get_pin_mask(chip, off); + unsigned long param = pinconf_to_config_param(config); + unsigned int reg; + int ret; + + mutex_lock(&chip->i2c_lock); + + /* Select port */ + ret = regmap_write(chip->regmap, CY8C95X0_PORTSEL, port); + if (ret < 0) + goto out; + + switch (param) { + case PIN_CONFIG_BIAS_PULL_UP: + __clear_bit(off, chip->push_pull); + reg = CY8C95X0_DRV_PU; + break; + case PIN_CONFIG_BIAS_PULL_DOWN: + __clear_bit(off, chip->push_pull); + reg = CY8C95X0_DRV_PD; + break; + case PIN_CONFIG_BIAS_DISABLE: + __clear_bit(off, chip->push_pull); + reg = CY8C95X0_DRV_HIZ; + break; + case PIN_CONFIG_DRIVE_OPEN_DRAIN: + __clear_bit(off, chip->push_pull); + reg = CY8C95X0_DRV_ODL; + break; + case PIN_CONFIG_DRIVE_OPEN_SOURCE: + __clear_bit(off, chip->push_pull); + reg = CY8C95X0_DRV_ODH; + break; + case PIN_CONFIG_DRIVE_PUSH_PULL: + __set_bit(off, chip->push_pull); + reg = CY8C95X0_DRV_PP_FAST; + break; + case PIN_CONFIG_MODE_PWM: + reg = CY8C95X0_PWMSEL; + break; + default: + ret = -ENOTSUPP; + goto out; + } + /* + * Writing 1 to one of the drive mode registers will automatically + * clear conflicting set bits in the other drive mode registers. + */ + ret = regmap_write_bits(chip->regmap, reg, bit, bit); + +out: + mutex_unlock(&chip->i2c_lock); + return ret; +} + +static int cy8c95x0_gpio_get_multiple(struct gpio_chip *gc, + unsigned long *mask, unsigned long *bits) +{ + struct cy8c95x0_pinctrl *chip = gpiochip_get_data(gc); + + return cy8c95x0_read_regs_mask(chip, CY8C95X0_INPUT, bits, mask); +} + +static void cy8c95x0_gpio_set_multiple(struct gpio_chip *gc, + unsigned long *mask, unsigned long *bits) +{ + struct cy8c95x0_pinctrl *chip = gpiochip_get_data(gc); + + cy8c95x0_write_regs_mask(chip, CY8C95X0_OUTPUT, bits, mask); +} + +static int cy8c95x0_add_pin_ranges(struct gpio_chip *gc) +{ + struct cy8c95x0_pinctrl *chip = gpiochip_get_data(gc); + struct device *dev = chip->dev; + int ret; + + ret = gpiochip_add_pin_range(gc, dev_name(dev), 0, 0, chip->tpin); + if (ret) + dev_err(dev, "failed to add GPIO pin range\n"); + + return ret; +} + +static int cy8c95x0_setup_gpiochip(struct cy8c95x0_pinctrl *chip) +{ + struct gpio_chip *gc = &chip->gpio_chip; + + gc->direction_input = cy8c95x0_gpio_direction_input; + gc->direction_output = cy8c95x0_gpio_direction_output; + gc->get = cy8c95x0_gpio_get_value; + gc->set = cy8c95x0_gpio_set_value; + gc->get_direction = cy8c95x0_gpio_get_direction; + gc->get_multiple = cy8c95x0_gpio_get_multiple; + gc->set_multiple = cy8c95x0_gpio_set_multiple; + gc->set_config = gpiochip_generic_config; + gc->can_sleep = true; + gc->add_pin_ranges = cy8c95x0_add_pin_ranges; + + gc->base = -1; + gc->ngpio = chip->tpin; + + gc->parent = chip->dev; + gc->owner = THIS_MODULE; + gc->names = NULL; + + gc->label = dev_name(chip->dev); + + return devm_gpiochip_add_data(chip->dev, gc, chip); +} + +static void cy8c95x0_irq_mask(struct irq_data *d) +{ + struct gpio_chip *gc = irq_data_get_irq_chip_data(d); + struct cy8c95x0_pinctrl *chip = gpiochip_get_data(gc); + irq_hw_number_t hwirq = irqd_to_hwirq(d); + + set_bit(hwirq, chip->irq_mask); + gpiochip_disable_irq(gc, hwirq); +} + +static void cy8c95x0_irq_unmask(struct irq_data *d) +{ + struct gpio_chip *gc = irq_data_get_irq_chip_data(d); + struct cy8c95x0_pinctrl *chip = gpiochip_get_data(gc); + irq_hw_number_t hwirq = irqd_to_hwirq(d); + + gpiochip_enable_irq(gc, hwirq); + clear_bit(hwirq, chip->irq_mask); +} + +static void cy8c95x0_irq_bus_lock(struct irq_data *d) +{ + struct gpio_chip *gc = irq_data_get_irq_chip_data(d); + struct cy8c95x0_pinctrl *chip = gpiochip_get_data(gc); + + mutex_lock(&chip->irq_lock); +} + +static void cy8c95x0_irq_bus_sync_unlock(struct irq_data *d) +{ + struct gpio_chip *gc = irq_data_get_irq_chip_data(d); + struct cy8c95x0_pinctrl *chip = gpiochip_get_data(gc); + DECLARE_BITMAP(ones, MAX_LINE); + DECLARE_BITMAP(irq_mask, MAX_LINE); + DECLARE_BITMAP(reg_direction, MAX_LINE); + + bitmap_fill(ones, MAX_LINE); + + cy8c95x0_write_regs_mask(chip, CY8C95X0_INTMASK, chip->irq_mask, ones); + + /* Switch direction to input if needed */ + cy8c95x0_read_regs_mask(chip, CY8C95X0_DIRECTION, reg_direction, chip->irq_mask); + bitmap_or(irq_mask, chip->irq_mask, reg_direction, MAX_LINE); + bitmap_complement(irq_mask, irq_mask, MAX_LINE); + + /* Look for any newly setup interrupt */ + cy8c95x0_write_regs_mask(chip, CY8C95X0_DIRECTION, ones, irq_mask); + + mutex_unlock(&chip->irq_lock); +} + +static int cy8c95x0_irq_set_type(struct irq_data *d, unsigned int type) +{ + struct gpio_chip *gc = irq_data_get_irq_chip_data(d); + struct cy8c95x0_pinctrl *chip = gpiochip_get_data(gc); + irq_hw_number_t hwirq = irqd_to_hwirq(d); + unsigned int trig_type; + + switch (type) { + case IRQ_TYPE_EDGE_RISING: + case IRQ_TYPE_EDGE_FALLING: + case IRQ_TYPE_EDGE_BOTH: + trig_type = type; + break; + case IRQ_TYPE_LEVEL_HIGH: + trig_type = IRQ_TYPE_EDGE_RISING; + break; + case IRQ_TYPE_LEVEL_LOW: + trig_type = IRQ_TYPE_EDGE_FALLING; + break; + default: + dev_err(chip->dev, "irq %d: unsupported type %d\n", d->irq, type); + return -EINVAL; + } + + assign_bit(hwirq, chip->irq_trig_fall, trig_type & IRQ_TYPE_EDGE_FALLING); + assign_bit(hwirq, chip->irq_trig_raise, trig_type & IRQ_TYPE_EDGE_RISING); + assign_bit(hwirq, chip->irq_trig_low, type == IRQ_TYPE_LEVEL_LOW); + assign_bit(hwirq, chip->irq_trig_high, type == IRQ_TYPE_LEVEL_HIGH); + + return 0; +} + +static void cy8c95x0_irq_shutdown(struct irq_data *d) +{ + struct gpio_chip *gc = irq_data_get_irq_chip_data(d); + struct cy8c95x0_pinctrl *chip = gpiochip_get_data(gc); + irq_hw_number_t hwirq = irqd_to_hwirq(d); + + clear_bit(hwirq, chip->irq_trig_raise); + clear_bit(hwirq, chip->irq_trig_fall); + clear_bit(hwirq, chip->irq_trig_low); + clear_bit(hwirq, chip->irq_trig_high); +} + +static const struct irq_chip cy8c95x0_irqchip = { + .name = "cy8c95x0-irq", + .irq_mask = cy8c95x0_irq_mask, + .irq_unmask = cy8c95x0_irq_unmask, + .irq_bus_lock = cy8c95x0_irq_bus_lock, + .irq_bus_sync_unlock = cy8c95x0_irq_bus_sync_unlock, + .irq_set_type = cy8c95x0_irq_set_type, + .irq_shutdown = cy8c95x0_irq_shutdown, + .flags = IRQCHIP_IMMUTABLE, + GPIOCHIP_IRQ_RESOURCE_HELPERS, +}; + +static bool cy8c95x0_irq_pending(struct cy8c95x0_pinctrl *chip, unsigned long *pending) +{ + DECLARE_BITMAP(ones, MAX_LINE); + DECLARE_BITMAP(cur_stat, MAX_LINE); + DECLARE_BITMAP(new_stat, MAX_LINE); + DECLARE_BITMAP(trigger, MAX_LINE); + + bitmap_fill(ones, MAX_LINE); + + /* Read the current interrupt status from the device */ + if (cy8c95x0_read_regs_mask(chip, CY8C95X0_INTSTATUS, trigger, ones)) + return false; + + /* Check latched inputs */ + if (cy8c95x0_read_regs_mask(chip, CY8C95X0_INPUT, cur_stat, trigger)) + return false; + + /* Apply filter for rising/falling edge selection */ + bitmap_replace(new_stat, chip->irq_trig_fall, chip->irq_trig_raise, + cur_stat, MAX_LINE); + + bitmap_and(pending, new_stat, trigger, MAX_LINE); + + return !bitmap_empty(pending, MAX_LINE); +} + +static irqreturn_t cy8c95x0_irq_handler(int irq, void *devid) +{ + struct cy8c95x0_pinctrl *chip = devid; + struct gpio_chip *gc = &chip->gpio_chip; + DECLARE_BITMAP(pending, MAX_LINE); + int nested_irq, level; + bool ret; + + ret = cy8c95x0_irq_pending(chip, pending); + if (!ret) + return IRQ_RETVAL(0); + + ret = 0; + for_each_set_bit(level, pending, MAX_LINE) { + /* Already accounted for 4bit gap in GPort2 */ + nested_irq = irq_find_mapping(gc->irq.domain, level); + + if (unlikely(nested_irq <= 0)) { + dev_warn_ratelimited(gc->parent, "unmapped interrupt %d\n", level); + continue; + } + + if (test_bit(level, chip->irq_trig_low)) + while (!cy8c95x0_gpio_get_value(gc, level)) + handle_nested_irq(nested_irq); + else if (test_bit(level, chip->irq_trig_high)) + while (cy8c95x0_gpio_get_value(gc, level)) + handle_nested_irq(nested_irq); + else + handle_nested_irq(nested_irq); + + ret = 1; + } + + return IRQ_RETVAL(ret); +} + +static int cy8c95x0_pinctrl_get_groups_count(struct pinctrl_dev *pctldev) +{ + struct cy8c95x0_pinctrl *chip = pinctrl_dev_get_drvdata(pctldev); + + return chip->tpin; +} + +static const char *cy8c95x0_pinctrl_get_group_name(struct pinctrl_dev *pctldev, + unsigned int group) +{ + return cy8c95x0_groups[group]; +} + +static int cy8c95x0_pinctrl_get_group_pins(struct pinctrl_dev *pctldev, + unsigned int group, + const unsigned int **pins, + unsigned int *num_pins) +{ + *pins = &cy8c9560_pins[group].number; + *num_pins = 1; + return 0; +} + +static const char *cy8c95x0_get_fname(unsigned int selector) +{ + if (selector == 0) + return "gpio"; + else + return "pwm"; +} + +static void cy8c95x0_pin_dbg_show(struct pinctrl_dev *pctldev, struct seq_file *s, + unsigned int pin) +{ + struct cy8c95x0_pinctrl *chip = pinctrl_dev_get_drvdata(pctldev); + DECLARE_BITMAP(mask, MAX_LINE); + DECLARE_BITMAP(pwm, MAX_LINE); + + bitmap_zero(mask, MAX_LINE); + __set_bit(pin, mask); + + if (cy8c95x0_read_regs_mask(chip, CY8C95X0_PWMSEL, pwm, mask)) { + seq_puts(s, "not available"); + return; + } + + seq_printf(s, "MODE:%s", cy8c95x0_get_fname(test_bit(pin, pwm))); +} + +static const struct pinctrl_ops cy8c95x0_pinctrl_ops = { + .get_groups_count = cy8c95x0_pinctrl_get_groups_count, + .get_group_name = cy8c95x0_pinctrl_get_group_name, + .get_group_pins = cy8c95x0_pinctrl_get_group_pins, +#ifdef CONFIG_OF + .dt_node_to_map = pinconf_generic_dt_node_to_map_pin, + .dt_free_map = pinconf_generic_dt_free_map, +#endif + .pin_dbg_show = cy8c95x0_pin_dbg_show, +}; + +static const char *cy8c95x0_get_function_name(struct pinctrl_dev *pctldev, unsigned int selector) +{ + return cy8c95x0_get_fname(selector); +} + +static int cy8c95x0_get_functions_count(struct pinctrl_dev *pctldev) +{ + return 2; +} + +static int cy8c95x0_get_function_groups(struct pinctrl_dev *pctldev, unsigned int selector, + const char * const **groups, + unsigned int * const num_groups) +{ + struct cy8c95x0_pinctrl *chip = pinctrl_dev_get_drvdata(pctldev); + + *groups = cy8c95x0_groups; + *num_groups = chip->tpin; + return 0; +} + +static int cy8c95x0_pinmux_cfg(struct cy8c95x0_pinctrl *chip, + unsigned int val, + unsigned long off) +{ + u8 port = cypress_get_port(chip, off); + u8 bit = cypress_get_pin_mask(chip, off); + int ret; + + /* Select port */ + ret = regmap_write(chip->regmap, CY8C95X0_PORTSEL, port); + if (ret < 0) + return ret; + + ret = regmap_write_bits(chip->regmap, CY8C95X0_PWMSEL, bit, val ? bit : 0); + if (ret < 0) + return ret; + + /* Set direction to output & set output to 1 so that PWM can work */ + ret = regmap_write_bits(chip->regmap, CY8C95X0_DIRECTION, bit, bit); + if (ret < 0) + return ret; + + return regmap_write_bits(chip->regmap, CY8C95X0_OUTPUT_(port), bit, bit); +} + +static int cy8c95x0_set_mux(struct pinctrl_dev *pctldev, unsigned int selector, + unsigned int group) +{ + struct cy8c95x0_pinctrl *chip = pinctrl_dev_get_drvdata(pctldev); + int ret; + + mutex_lock(&chip->i2c_lock); + ret = cy8c95x0_pinmux_cfg(chip, selector, group); + mutex_unlock(&chip->i2c_lock); + + return ret; +} + +static const struct pinmux_ops cy8c95x0_pmxops = { + .get_functions_count = cy8c95x0_get_functions_count, + .get_function_name = cy8c95x0_get_function_name, + .get_function_groups = cy8c95x0_get_function_groups, + .set_mux = cy8c95x0_set_mux, + .strict = true, +}; + +static int cy8c95x0_pinconf_get(struct pinctrl_dev *pctldev, unsigned int pin, + unsigned long *config) +{ + struct cy8c95x0_pinctrl *chip = pinctrl_dev_get_drvdata(pctldev); + + return cy8c95x0_gpio_get_pincfg(chip, pin, config); +} + +static int cy8c95x0_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin, + unsigned long *configs, unsigned int num_configs) +{ + struct cy8c95x0_pinctrl *chip = pinctrl_dev_get_drvdata(pctldev); + int ret = 0; + int i; + + for (i = 0; i < num_configs; i++) { + ret = cy8c95x0_gpio_set_pincfg(chip, pin, configs[i]); + if (ret) + return ret; + } + + return ret; +} + +static const struct pinconf_ops cy8c95x0_pinconf_ops = { + .pin_config_get = cy8c95x0_pinconf_get, + .pin_config_set = cy8c95x0_pinconf_set, + .is_generic = true, +}; + +static int cy8c95x0_irq_setup(struct cy8c95x0_pinctrl *chip, int irq) +{ + struct gpio_irq_chip *girq = &chip->gpio_chip.irq; + DECLARE_BITMAP(pending_irqs, MAX_LINE); + int ret; + + mutex_init(&chip->irq_lock); + + bitmap_zero(pending_irqs, MAX_LINE); + + /* Read IRQ status register to clear all pending interrupts */ + ret = cy8c95x0_irq_pending(chip, pending_irqs); + if (ret) { + dev_err(chip->dev, "failed to clear irq status register\n"); + return ret; + } + + /* Mask all interrupts */ + bitmap_fill(chip->irq_mask, MAX_LINE); + + gpio_irq_chip_set_chip(girq, &cy8c95x0_irqchip); + + /* This will let us handle the parent IRQ in the driver */ + girq->parent_handler = NULL; + girq->num_parents = 0; + girq->parents = NULL; + girq->default_type = IRQ_TYPE_NONE; + girq->handler = handle_simple_irq; + girq->threaded = true; + + ret = devm_request_threaded_irq(chip->dev, irq, + NULL, cy8c95x0_irq_handler, + IRQF_ONESHOT | IRQF_SHARED | IRQF_TRIGGER_HIGH, + dev_name(chip->dev), chip); + if (ret) { + dev_err(chip->dev, "failed to request irq %d\n", irq); + return ret; + } + dev_info(chip->dev, "Registered threaded IRQ\n"); + + return 0; +} + +static int cy8c95x0_setup_pinctrl(struct cy8c95x0_pinctrl *chip) +{ + struct pinctrl_desc *pd = &chip->pinctrl_desc; + + pd->pctlops = &cy8c95x0_pinctrl_ops; + pd->confops = &cy8c95x0_pinconf_ops; + pd->pmxops = &cy8c95x0_pmxops; + pd->name = dev_name(chip->dev); + pd->pins = cy8c9560_pins; + pd->npins = chip->tpin; + pd->owner = THIS_MODULE; + + chip->pctldev = devm_pinctrl_register(chip->dev, pd, chip); + if (IS_ERR(chip->pctldev)) + return dev_err_probe(chip->dev, PTR_ERR(chip->pctldev), + "can't register controller\n"); + + return 0; +} + +static int cy8c95x0_detect(struct i2c_client *client, + struct i2c_board_info *info) +{ + struct i2c_adapter *adapter = client->adapter; + int ret; + const char *name; + + if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) + return -ENODEV; + + ret = i2c_smbus_read_byte_data(client, CY8C95X0_DEVID); + if (ret < 0) + return ret; + switch (ret & GENMASK(7, 4)) { + case 0x20: + name = cy8c95x0_id[0].name; + break; + case 0x40: + name = cy8c95x0_id[1].name; + break; + case 0x60: + name = cy8c95x0_id[2].name; + break; + default: + return -ENODEV; + } + + dev_info(&client->dev, "Found a %s chip at 0x%02x.\n", name, client->addr); + strscpy(info->type, name, I2C_NAME_SIZE); + + return 0; +} + +static int cy8c95x0_probe(struct i2c_client *client) +{ + struct cy8c95x0_pinctrl *chip; + struct regulator *reg; + int ret; + + chip = devm_kzalloc(&client->dev, sizeof(*chip), GFP_KERNEL); + if (!chip) + return -ENOMEM; + + chip->dev = &client->dev; + + /* Set the device type */ + chip->driver_data = (unsigned long)device_get_match_data(&client->dev); + if (!chip->driver_data) + chip->driver_data = i2c_match_id(cy8c95x0_id, client)->driver_data; + if (!chip->driver_data) + return -ENODEV; + + i2c_set_clientdata(client, chip); + + chip->tpin = chip->driver_data & CY8C95X0_GPIO_MASK; + chip->nport = DIV_ROUND_UP(CY8C95X0_PIN_TO_OFFSET(chip->tpin), BANK_SZ); + + switch (chip->tpin) { + case 20: + strscpy(chip->name, cy8c95x0_id[0].name, I2C_NAME_SIZE); + break; + case 40: + strscpy(chip->name, cy8c95x0_id[1].name, I2C_NAME_SIZE); + break; + case 60: + strscpy(chip->name, cy8c95x0_id[2].name, I2C_NAME_SIZE); + break; + default: + return -ENODEV; + } + + reg = devm_regulator_get(&client->dev, "vdd"); + if (IS_ERR(reg)) { + if (PTR_ERR(reg) == -EPROBE_DEFER) + return -EPROBE_DEFER; + } else { + ret = regulator_enable(reg); + if (ret) { + dev_err(&client->dev, "failed to enable regulator vdd: %d\n", ret); + return ret; + } + chip->regulator = reg; + } + + chip->regmap = devm_regmap_init_i2c(client, &cy8c95x0_i2c_regmap); + if (IS_ERR(chip->regmap)) { + ret = PTR_ERR(chip->regmap); + goto err_exit; + } + + bitmap_zero(chip->push_pull, MAX_LINE); + bitmap_zero(chip->shiftmask, MAX_LINE); + bitmap_set(chip->shiftmask, 0, 20); + mutex_init(&chip->i2c_lock); + + if (dmi_first_match(cy8c95x0_dmi_acpi_irq_info)) { + ret = cy8c95x0_acpi_get_irq(&client->dev); + if (ret > 0) + client->irq = ret; + } + + if (client->irq) { + ret = cy8c95x0_irq_setup(chip, client->irq); + if (ret) + goto err_exit; + } + + ret = cy8c95x0_setup_pinctrl(chip); + if (ret) + goto err_exit; + + ret = cy8c95x0_setup_gpiochip(chip); + if (ret) + goto err_exit; + + return 0; + +err_exit: + if (!IS_ERR_OR_NULL(chip->regulator)) + regulator_disable(chip->regulator); + return ret; +} + +static void cy8c95x0_remove(struct i2c_client *client) +{ + struct cy8c95x0_pinctrl *chip = i2c_get_clientdata(client); + + if (!IS_ERR_OR_NULL(chip->regulator)) + regulator_disable(chip->regulator); +} + +static const struct acpi_device_id cy8c95x0_acpi_ids[] = { + { "INT3490", 40, }, + { } +}; +MODULE_DEVICE_TABLE(acpi, cy8c95x0_acpi_ids); + +static struct i2c_driver cy8c95x0_driver = { + .driver = { + .name = "cy8c95x0-pinctrl", + .of_match_table = cy8c95x0_dt_ids, + .acpi_match_table = cy8c95x0_acpi_ids, + }, + .probe_new = cy8c95x0_probe, + .remove = cy8c95x0_remove, + .id_table = cy8c95x0_id, + .detect = cy8c95x0_detect, +}; +module_i2c_driver(cy8c95x0_driver); + +MODULE_AUTHOR("Patrick Rudolph <patrick.rudolph@9elements.com>"); +MODULE_AUTHOR("Naresh Solanki <naresh.solanki@9elements.com>"); +MODULE_DESCRIPTION("Pinctrl driver for CY8C95X0"); +MODULE_LICENSE("GPL"); |