diff options
Diffstat (limited to '')
| -rw-r--r-- | tools/testing/selftests/sysctl/Makefile | 13 | ||||
| -rw-r--r-- | tools/testing/selftests/sysctl/config | 1 | ||||
| -rwxr-xr-x | tools/testing/selftests/sysctl/sysctl.sh | 994 |
3 files changed, 1008 insertions, 0 deletions
diff --git a/tools/testing/selftests/sysctl/Makefile b/tools/testing/selftests/sysctl/Makefile new file mode 100644 index 000000000..110301f9f --- /dev/null +++ b/tools/testing/selftests/sysctl/Makefile @@ -0,0 +1,13 @@ +# SPDX-License-Identifier: GPL-2.0-only +# Makefile for sysctl selftests. +# Expects kernel.sysctl_writes_strict=1. + +# No binaries, but make sure arg-less "make" doesn't trigger "run_tests". +all: + +TEST_PROGS := sysctl.sh + +include ../lib.mk + +# Nothing to clean up. +clean: diff --git a/tools/testing/selftests/sysctl/config b/tools/testing/selftests/sysctl/config new file mode 100644 index 000000000..fc263efd1 --- /dev/null +++ b/tools/testing/selftests/sysctl/config @@ -0,0 +1 @@ +CONFIG_TEST_SYSCTL=m diff --git a/tools/testing/selftests/sysctl/sysctl.sh b/tools/testing/selftests/sysctl/sysctl.sh new file mode 100755 index 000000000..f50778a3d --- /dev/null +++ b/tools/testing/selftests/sysctl/sysctl.sh @@ -0,0 +1,994 @@ +#!/bin/bash +# Copyright (C) 2017 Luis R. Rodriguez <mcgrof@kernel.org> +# +# This program is free software; you can redistribute it and/or modify it +# under the terms of the GNU General Public License as published by the Free +# Software Foundation; either version 2 of the License, or at your option any +# later version; or, when distributed separately from the Linux kernel or +# when incorporated into other software packages, subject to the following +# license: +# +# This program is free software; you can redistribute it and/or modify it +# under the terms of copyleft-next (version 0.3.1 or later) as published +# at http://copyleft-next.org/. + +# This performs a series tests against the proc sysctl interface. + +# Kselftest framework requirement - SKIP code is 4. +ksft_skip=4 + +TEST_NAME="sysctl" +TEST_DRIVER="test_${TEST_NAME}" +TEST_DIR=$(dirname $0) +TEST_FILE=$(mktemp) + +# This represents +# +# TEST_ID:TEST_COUNT:ENABLED:TARGET +# +# TEST_ID: is the test id number +# TEST_COUNT: number of times we should run the test +# ENABLED: 1 if enabled, 0 otherwise +# TARGET: test target file required on the test_sysctl module +# +# Once these are enabled please leave them as-is. Write your own test, +# we have tons of space. +ALL_TESTS="0001:1:1:int_0001" +ALL_TESTS="$ALL_TESTS 0002:1:1:string_0001" +ALL_TESTS="$ALL_TESTS 0003:1:1:int_0002" +ALL_TESTS="$ALL_TESTS 0004:1:1:uint_0001" +ALL_TESTS="$ALL_TESTS 0005:3:1:int_0003" +ALL_TESTS="$ALL_TESTS 0006:50:1:bitmap_0001" +ALL_TESTS="$ALL_TESTS 0007:1:1:boot_int" +ALL_TESTS="$ALL_TESTS 0008:1:1:match_int" + +function allow_user_defaults() +{ + if [ -z $DIR ]; then + DIR="/sys/module/test_sysctl/" + fi + if [ -z $DEFAULT_NUM_TESTS ]; then + DEFAULT_NUM_TESTS=50 + fi + if [ -z $SYSCTL ]; then + SYSCTL="/proc/sys/debug/test_sysctl" + fi + if [ -z $PROD_SYSCTL ]; then + PROD_SYSCTL="/proc/sys" + fi + if [ -z $WRITES_STRICT ]; then + WRITES_STRICT="${PROD_SYSCTL}/kernel/sysctl_writes_strict" + fi +} + +function check_production_sysctl_writes_strict() +{ + echo -n "Checking production write strict setting ... " + if [ ! -e ${WRITES_STRICT} ]; then + echo "FAIL, but skip in case of old kernel" >&2 + else + old_strict=$(cat ${WRITES_STRICT}) + if [ "$old_strict" = "1" ]; then + echo "ok" + else + echo "FAIL, strict value is 0 but force to 1 to continue" >&2 + echo "1" > ${WRITES_STRICT} + fi + fi + + if [ -z $PAGE_SIZE ]; then + PAGE_SIZE=$(getconf PAGESIZE) + fi + if [ -z $MAX_DIGITS ]; then + MAX_DIGITS=$(($PAGE_SIZE/8)) + fi + if [ -z $INT_MAX ]; then + INT_MAX=$(getconf INT_MAX) + fi + if [ -z $UINT_MAX ]; then + UINT_MAX=$(getconf UINT_MAX) + fi +} + +test_reqs() +{ + uid=$(id -u) + if [ $uid -ne 0 ]; then + echo $msg must be run as root >&2 + exit $ksft_skip + fi + + if ! which perl 2> /dev/null > /dev/null; then + echo "$0: You need perl installed" + exit $ksft_skip + fi + if ! which getconf 2> /dev/null > /dev/null; then + echo "$0: You need getconf installed" + exit $ksft_skip + fi + if ! which diff 2> /dev/null > /dev/null; then + echo "$0: You need diff installed" + exit $ksft_skip + fi +} + +function load_req_mod() +{ + if [ ! -d $SYSCTL ]; then + if ! modprobe -q -n $TEST_DRIVER; then + echo "$0: module $TEST_DRIVER not found [SKIP]" + echo "You must set CONFIG_TEST_SYSCTL=m in your kernel" >&2 + exit $ksft_skip + fi + modprobe $TEST_DRIVER + if [ $? -ne 0 ]; then + echo "$0: modprobe $TEST_DRIVER failed." + exit + fi + fi +} + +reset_vals() +{ + VAL="" + TRIGGER=$(basename ${TARGET}) + case "$TRIGGER" in + int_0001) + VAL="60" + ;; + int_0002) + VAL="1" + ;; + uint_0001) + VAL="314" + ;; + string_0001) + VAL="(none)" + ;; + bitmap_0001) + VAL="" + ;; + *) + ;; + esac + echo -n $VAL > $TARGET +} + +set_orig() +{ + if [ ! -z $TARGET ] && [ ! -z $ORIG ]; then + if [ -f ${TARGET} ]; then + echo "${ORIG}" > "${TARGET}" + fi + fi +} + +set_test() +{ + echo "${TEST_STR}" > "${TARGET}" +} + +verify() +{ + local seen + seen=$(cat "$1") + if [ "${seen}" != "${TEST_STR}" ]; then + return 1 + fi + return 0 +} + +# proc files get read a page at a time, which can confuse diff, +# and get you incorrect results on proc files with long data. To use +# diff against them you must first extract the output to a file, and +# then compare against that file. +verify_diff_proc_file() +{ + TMP_DUMP_FILE=$(mktemp) + cat $1 > $TMP_DUMP_FILE + + if ! diff -w -q $TMP_DUMP_FILE $2; then + return 1 + else + return 0 + fi +} + +verify_diff_w() +{ + echo "$TEST_STR" | diff -q -w -u - $1 > /dev/null + return $? +} + +test_rc() +{ + if [[ $rc != 0 ]]; then + echo "Failed test, return value: $rc" >&2 + exit $rc + fi +} + +test_finish() +{ + set_orig + rm -f "${TEST_FILE}" + + if [ ! -z ${old_strict} ]; then + echo ${old_strict} > ${WRITES_STRICT} + fi + exit $rc +} + +run_numerictests() +{ + echo "== Testing sysctl behavior against ${TARGET} ==" + + rc=0 + + echo -n "Writing test file ... " + echo "${TEST_STR}" > "${TEST_FILE}" + if ! verify "${TEST_FILE}"; then + echo "FAIL" >&2 + exit 1 + else + echo "ok" + fi + + echo -n "Checking sysctl is not set to test value ... " + if verify "${TARGET}"; then + echo "FAIL" >&2 + exit 1 + else + echo "ok" + fi + + echo -n "Writing sysctl from shell ... " + set_test + if ! verify "${TARGET}"; then + echo "FAIL" >&2 + exit 1 + else + echo "ok" + fi + + echo -n "Resetting sysctl to original value ... " + set_orig + if verify "${TARGET}"; then + echo "FAIL" >&2 + exit 1 + else + echo "ok" + fi + + # Now that we've validated the sanity of "set_test" and "set_orig", + # we can use those functions to set starting states before running + # specific behavioral tests. + + echo -n "Writing entire sysctl in single write ... " + set_orig + dd if="${TEST_FILE}" of="${TARGET}" bs=4096 2>/dev/null + if ! verify "${TARGET}"; then + echo "FAIL" >&2 + rc=1 + else + echo "ok" + fi + + echo -n "Writing middle of sysctl after synchronized seek ... " + set_test + dd if="${TEST_FILE}" of="${TARGET}" bs=1 seek=1 skip=1 2>/dev/null + if ! verify "${TARGET}"; then + echo "FAIL" >&2 + rc=1 + else + echo "ok" + fi + + echo -n "Writing beyond end of sysctl ... " + set_orig + dd if="${TEST_FILE}" of="${TARGET}" bs=20 seek=2 2>/dev/null + if verify "${TARGET}"; then + echo "FAIL" >&2 + rc=1 + else + echo "ok" + fi + + echo -n "Writing sysctl with multiple long writes ... " + set_orig + (perl -e 'print "A" x 50;'; echo "${TEST_STR}") | \ + dd of="${TARGET}" bs=50 2>/dev/null + if verify "${TARGET}"; then + echo "FAIL" >&2 + rc=1 + else + echo "ok" + fi + test_rc +} + +check_failure() +{ + echo -n "Testing that $1 fails as expected..." + reset_vals + TEST_STR="$1" + orig="$(cat $TARGET)" + echo -n "$TEST_STR" > $TARGET 2> /dev/null + + # write should fail and $TARGET should retain its original value + if [ $? = 0 ] || [ "$(cat $TARGET)" != "$orig" ]; then + echo "FAIL" >&2 + rc=1 + else + echo "ok" + fi + test_rc +} + +run_wideint_tests() +{ + # sysctl conversion functions receive a boolean sign and ulong + # magnitude; here we list the magnitudes we want to test (each of + # which will be tested in both positive and negative forms). Since + # none of these values fit in 32 bits, writing them to an int- or + # uint-typed sysctl should fail. + local magnitudes=( + # common boundary-condition values (zero, +1, -1, INT_MIN, + # and INT_MAX respectively) if truncated to lower 32 bits + # (potential for being falsely deemed in range) + 0x0000000100000000 + 0x0000000100000001 + 0x00000001ffffffff + 0x0000000180000000 + 0x000000017fffffff + + # these look like negatives, but without a leading '-' are + # actually large positives (should be rejected as above + # despite being zero/+1/-1/INT_MIN/INT_MAX in the lower 32) + 0xffffffff00000000 + 0xffffffff00000001 + 0xffffffffffffffff + 0xffffffff80000000 + 0xffffffff7fffffff + ) + + for sign in '' '-'; do + for mag in "${magnitudes[@]}"; do + check_failure "${sign}${mag}" + done + done +} + +# Your test must accept digits 3 and 4 to use this +run_limit_digit() +{ + echo -n "Checking ignoring spaces up to PAGE_SIZE works on write ..." + reset_vals + + LIMIT=$((MAX_DIGITS -1)) + TEST_STR="3" + (perl -e 'print " " x '$LIMIT';'; echo "${TEST_STR}") | \ + dd of="${TARGET}" 2>/dev/null + + if ! verify "${TARGET}"; then + echo "FAIL" >&2 + rc=1 + else + echo "ok" + fi + test_rc + + echo -n "Checking passing PAGE_SIZE of spaces fails on write ..." + reset_vals + + LIMIT=$((MAX_DIGITS)) + TEST_STR="4" + (perl -e 'print " " x '$LIMIT';'; echo "${TEST_STR}") | \ + dd of="${TARGET}" 2>/dev/null + + if verify "${TARGET}"; then + echo "FAIL" >&2 + rc=1 + else + echo "ok" + fi + test_rc +} + +# You are using an int +run_limit_digit_int() +{ + echo -n "Testing INT_MAX works ..." + reset_vals + TEST_STR="$INT_MAX" + echo -n $TEST_STR > $TARGET + + if ! verify "${TARGET}"; then + echo "FAIL" >&2 + rc=1 + else + echo "ok" + fi + test_rc + + echo -n "Testing INT_MAX + 1 will fail as expected..." + reset_vals + let TEST_STR=$INT_MAX+1 + echo -n $TEST_STR > $TARGET 2> /dev/null + + if verify "${TARGET}"; then + echo "FAIL" >&2 + rc=1 + else + echo "ok" + fi + test_rc + + echo -n "Testing negative values will work as expected..." + reset_vals + TEST_STR="-3" + echo -n $TEST_STR > $TARGET 2> /dev/null + if ! verify "${TARGET}"; then + echo "FAIL" >&2 + rc=1 + else + echo "ok" + fi + test_rc +} + +# You used an int array +run_limit_digit_int_array() +{ + echo -n "Testing array works as expected ... " + TEST_STR="4 3 2 1" + echo -n $TEST_STR > $TARGET + + if ! verify_diff_w "${TARGET}"; then + echo "FAIL" >&2 + rc=1 + else + echo "ok" + fi + test_rc + + echo -n "Testing skipping trailing array elements works ... " + # Do not reset_vals, carry on the values from the last test. + # If we only echo in two digits the last two are left intact + TEST_STR="100 101" + echo -n $TEST_STR > $TARGET + # After we echo in, to help diff we need to set on TEST_STR what + # we expect the result to be. + TEST_STR="100 101 2 1" + + if ! verify_diff_w "${TARGET}"; then + echo "FAIL" >&2 + rc=1 + else + echo "ok" + fi + test_rc + + echo -n "Testing PAGE_SIZE limit on array works ... " + # Do not reset_vals, carry on the values from the last test. + # Even if you use an int array, you are still restricted to + # MAX_DIGITS, this is a known limitation. Test limit works. + LIMIT=$((MAX_DIGITS -1)) + TEST_STR="9" + (perl -e 'print " " x '$LIMIT';'; echo "${TEST_STR}") | \ + dd of="${TARGET}" 2>/dev/null + + TEST_STR="9 101 2 1" + if ! verify_diff_w "${TARGET}"; then + echo "FAIL" >&2 + rc=1 + else + echo "ok" + fi + test_rc + + echo -n "Testing exceeding PAGE_SIZE limit fails as expected ... " + # Do not reset_vals, carry on the values from the last test. + # Now go over limit. + LIMIT=$((MAX_DIGITS)) + TEST_STR="7" + (perl -e 'print " " x '$LIMIT';'; echo "${TEST_STR}") | \ + dd of="${TARGET}" 2>/dev/null + + TEST_STR="7 101 2 1" + if verify_diff_w "${TARGET}"; then + echo "FAIL" >&2 + rc=1 + else + echo "ok" + fi + test_rc +} + +# You are using an unsigned int +run_limit_digit_uint() +{ + echo -n "Testing UINT_MAX works ..." + reset_vals + TEST_STR="$UINT_MAX" + echo -n $TEST_STR > $TARGET + + if ! verify "${TARGET}"; then + echo "FAIL" >&2 + rc=1 + else + echo "ok" + fi + test_rc + + echo -n "Testing UINT_MAX + 1 will fail as expected..." + reset_vals + TEST_STR=$(($UINT_MAX+1)) + echo -n $TEST_STR > $TARGET 2> /dev/null + + if verify "${TARGET}"; then + echo "FAIL" >&2 + rc=1 + else + echo "ok" + fi + test_rc + + echo -n "Testing negative values will not work as expected ..." + reset_vals + TEST_STR="-3" + echo -n $TEST_STR > $TARGET 2> /dev/null + + if verify "${TARGET}"; then + echo "FAIL" >&2 + rc=1 + else + echo "ok" + fi + test_rc +} + +run_stringtests() +{ + echo -n "Writing entire sysctl in short writes ... " + set_orig + dd if="${TEST_FILE}" of="${TARGET}" bs=1 2>/dev/null + if ! verify "${TARGET}"; then + echo "FAIL" >&2 + rc=1 + else + echo "ok" + fi + + echo -n "Writing middle of sysctl after unsynchronized seek ... " + set_test + dd if="${TEST_FILE}" of="${TARGET}" bs=1 seek=1 2>/dev/null + if verify "${TARGET}"; then + echo "FAIL" >&2 + rc=1 + else + echo "ok" + fi + + echo -n "Checking sysctl maxlen is at least $MAXLEN ... " + set_orig + perl -e 'print "A" x ('"${MAXLEN}"'-2), "B";' | \ + dd of="${TARGET}" bs="${MAXLEN}" 2>/dev/null + if ! grep -q B "${TARGET}"; then + echo "FAIL" >&2 + rc=1 + else + echo "ok" + fi + + echo -n "Checking sysctl keeps original string on overflow append ... " + set_orig + perl -e 'print "A" x ('"${MAXLEN}"'-1), "B";' | \ + dd of="${TARGET}" bs=$(( MAXLEN - 1 )) 2>/dev/null + if grep -q B "${TARGET}"; then + echo "FAIL" >&2 + rc=1 + else + echo "ok" + fi + + echo -n "Checking sysctl stays NULL terminated on write ... " + set_orig + perl -e 'print "A" x ('"${MAXLEN}"'-1), "B";' | \ + dd of="${TARGET}" bs="${MAXLEN}" 2>/dev/null + if grep -q B "${TARGET}"; then + echo "FAIL" >&2 + rc=1 + else + echo "ok" + fi + + echo -n "Checking sysctl stays NULL terminated on overwrite ... " + set_orig + perl -e 'print "A" x ('"${MAXLEN}"'-1), "BB";' | \ + dd of="${TARGET}" bs=$(( $MAXLEN + 1 )) 2>/dev/null + if grep -q B "${TARGET}"; then + echo "FAIL" >&2 + rc=1 + else + echo "ok" + fi + + test_rc +} + +target_exists() +{ + TARGET="${SYSCTL}/$1" + TEST_ID="$2" + + if [ ! -f ${TARGET} ] ; then + echo "Target for test $TEST_ID: $TARGET not exist, skipping test ..." + return 0 + fi + return 1 +} + +run_bitmaptest() { + # Total length of bitmaps string to use, a bit under + # the maximum input size of the test node + LENGTH=$((RANDOM % 65000)) + + # First bit to set + BIT=$((RANDOM % 1024)) + + # String containing our list of bits to set + TEST_STR=$BIT + + # build up the string + while [ "${#TEST_STR}" -le "$LENGTH" ]; do + # Make sure next entry is discontiguous, + # skip ahead at least 2 + BIT=$((BIT + $((2 + RANDOM % 10)))) + + # Add new bit to the list + TEST_STR="${TEST_STR},${BIT}" + + # Randomly make it a range + if [ "$((RANDOM % 2))" -eq "1" ]; then + RANGE_END=$((BIT + $((1 + RANDOM % 10)))) + TEST_STR="${TEST_STR}-${RANGE_END}" + BIT=$RANGE_END + fi + done + + echo -n "Checking bitmap handler... " + TEST_FILE=$(mktemp) + echo -n "$TEST_STR" > $TEST_FILE + + cat $TEST_FILE > $TARGET 2> /dev/null + if [ $? -ne 0 ]; then + echo "FAIL" >&2 + rc=1 + test_rc + fi + + if ! verify_diff_proc_file "$TARGET" "$TEST_FILE"; then + echo "FAIL" >&2 + rc=1 + else + echo "ok" + rc=0 + fi + test_rc +} + +sysctl_test_0001() +{ + TARGET="${SYSCTL}/$(get_test_target 0001)" + reset_vals + ORIG=$(cat "${TARGET}") + TEST_STR=$(( $ORIG + 1 )) + + run_numerictests + run_wideint_tests + run_limit_digit +} + +sysctl_test_0002() +{ + TARGET="${SYSCTL}/$(get_test_target 0002)" + reset_vals + ORIG=$(cat "${TARGET}") + TEST_STR="Testing sysctl" + # Only string sysctls support seeking/appending. + MAXLEN=65 + + run_numerictests + run_stringtests +} + +sysctl_test_0003() +{ + TARGET="${SYSCTL}/$(get_test_target 0003)" + reset_vals + ORIG=$(cat "${TARGET}") + TEST_STR=$(( $ORIG + 1 )) + + run_numerictests + run_wideint_tests + run_limit_digit + run_limit_digit_int +} + +sysctl_test_0004() +{ + TARGET="${SYSCTL}/$(get_test_target 0004)" + reset_vals + ORIG=$(cat "${TARGET}") + TEST_STR=$(( $ORIG + 1 )) + + run_numerictests + run_wideint_tests + run_limit_digit + run_limit_digit_uint +} + +sysctl_test_0005() +{ + TARGET="${SYSCTL}/$(get_test_target 0005)" + reset_vals + ORIG=$(cat "${TARGET}") + + run_limit_digit_int_array +} + +sysctl_test_0006() +{ + TARGET="${SYSCTL}/bitmap_0001" + reset_vals + ORIG="" + run_bitmaptest +} + +sysctl_test_0007() +{ + TARGET="${SYSCTL}/boot_int" + if [ ! -f $TARGET ]; then + echo "Skipping test for $TARGET as it is not present ..." + return $ksft_skip + fi + + if [ -d $DIR ]; then + echo "Boot param test only possible sysctl_test is built-in, not module:" + cat $TEST_DIR/config >&2 + return $ksft_skip + fi + + echo -n "Testing if $TARGET is set to 1 ..." + ORIG=$(cat "${TARGET}") + + if [ x$ORIG = "x1" ]; then + echo "ok" + return 0 + fi + echo "FAIL" + echo "Checking if /proc/cmdline contains setting of the expected parameter ..." + if [ ! -f /proc/cmdline ]; then + echo "/proc/cmdline does not exist, test inconclusive" + return 0 + fi + + FOUND=$(grep -c "sysctl[./]debug[./]test_sysctl[./]boot_int=1" /proc/cmdline) + if [ $FOUND = "1" ]; then + echo "Kernel param found but $TARGET is not 1, TEST FAILED" + rc=1 + test_rc + fi + + echo "Skipping test, expected kernel parameter missing." + echo "To perform this test, make sure kernel is booted with parameter: sysctl.debug.test_sysctl.boot_int=1" + return $ksft_skip +} + +sysctl_test_0008() +{ + TARGET="${SYSCTL}/match_int" + if [ ! -f $TARGET ]; then + echo "Skipping test for $TARGET as it is not present ..." + return $ksft_skip + fi + + echo -n "Testing if $TARGET is matched in kernel" + ORIG_VALUE=$(cat "${TARGET}") + + if [ $ORIG_VALUE -ne 1 ]; then + echo "TEST FAILED" + rc=1 + test_rc + fi + + echo "ok" + return 0 +} + +list_tests() +{ + echo "Test ID list:" + echo + echo "TEST_ID x NUM_TEST" + echo "TEST_ID: Test ID" + echo "NUM_TESTS: Number of recommended times to run the test" + echo + echo "0001 x $(get_test_count 0001) - tests proc_dointvec_minmax()" + echo "0002 x $(get_test_count 0002) - tests proc_dostring()" + echo "0003 x $(get_test_count 0003) - tests proc_dointvec()" + echo "0004 x $(get_test_count 0004) - tests proc_douintvec()" + echo "0005 x $(get_test_count 0005) - tests proc_douintvec() array" + echo "0006 x $(get_test_count 0006) - tests proc_do_large_bitmap()" + echo "0007 x $(get_test_count 0007) - tests setting sysctl from kernel boot param" + echo "0008 x $(get_test_count 0008) - tests sysctl macro values match" +} + +usage() +{ + NUM_TESTS=$(grep -o ' ' <<<"$ALL_TESTS" | grep -c .) + let NUM_TESTS=$NUM_TESTS+1 + MAX_TEST=$(printf "%04d\n" $NUM_TESTS) + echo "Usage: $0 [ -t <4-number-digit> ] | [ -w <4-number-digit> ] |" + echo " [ -s <4-number-digit> ] | [ -c <4-number-digit> <test- count>" + echo " [ all ] [ -h | --help ] [ -l ]" + echo "" + echo "Valid tests: 0001-$MAX_TEST" + echo "" + echo " all Runs all tests (default)" + echo " -t Run test ID the number amount of times is recommended" + echo " -w Watch test ID run until it runs into an error" + echo " -c Run test ID once" + echo " -s Run test ID x test-count number of times" + echo " -l List all test ID list" + echo " -h|--help Help" + echo + echo "If an error every occurs execution will immediately terminate." + echo "If you are adding a new test try using -w <test-ID> first to" + echo "make sure the test passes a series of tests." + echo + echo Example uses: + echo + echo "$TEST_NAME.sh -- executes all tests" + echo "$TEST_NAME.sh -t 0002 -- Executes test ID 0002 number of times is recomended" + echo "$TEST_NAME.sh -w 0002 -- Watch test ID 0002 run until an error occurs" + echo "$TEST_NAME.sh -s 0002 -- Run test ID 0002 once" + echo "$TEST_NAME.sh -c 0002 3 -- Run test ID 0002 three times" + echo + list_tests + exit 1 +} + +function test_num() +{ + re='^[0-9]+$' + if ! [[ $1 =~ $re ]]; then + usage + fi +} + +function get_test_count() +{ + test_num $1 + TEST_DATA=$(echo $ALL_TESTS | awk '{print $'$1'}') + echo ${TEST_DATA} | awk -F":" '{print $2}' +} + +function get_test_enabled() +{ + test_num $1 + TEST_DATA=$(echo $ALL_TESTS | awk '{print $'$1'}') + echo ${TEST_DATA} | awk -F":" '{print $3}' +} + +function get_test_target() +{ + test_num $1 + TEST_DATA=$(echo $ALL_TESTS | awk '{print $'$1'}') + echo ${TEST_DATA} | awk -F":" '{print $4}' +} + +function run_all_tests() +{ + for i in $ALL_TESTS ; do + TEST_ID=${i%:*:*:*} + ENABLED=$(get_test_enabled $TEST_ID) + TEST_COUNT=$(get_test_count $TEST_ID) + TEST_TARGET=$(get_test_target $TEST_ID) + if target_exists $TEST_TARGET $TEST_ID; then + continue + fi + if [[ $ENABLED -eq "1" ]]; then + test_case $TEST_ID $TEST_COUNT $TEST_TARGET + fi + done +} + +function watch_log() +{ + if [ $# -ne 3 ]; then + clear + fi + date + echo "Running test: $2 - run #$1" +} + +function watch_case() +{ + i=0 + while [ 1 ]; do + + if [ $# -eq 1 ]; then + test_num $1 + watch_log $i ${TEST_NAME}_test_$1 + ${TEST_NAME}_test_$1 + else + watch_log $i all + run_all_tests + fi + let i=$i+1 + done +} + +function test_case() +{ + NUM_TESTS=$2 + + i=0 + + if target_exists $3 $1; then + continue + fi + + while [ $i -lt $NUM_TESTS ]; do + test_num $1 + watch_log $i ${TEST_NAME}_test_$1 noclear + RUN_TEST=${TEST_NAME}_test_$1 + $RUN_TEST + let i=$i+1 + done +} + +function parse_args() +{ + if [ $# -eq 0 ]; then + run_all_tests + else + if [[ "$1" = "all" ]]; then + run_all_tests + elif [[ "$1" = "-w" ]]; then + shift + watch_case $@ + elif [[ "$1" = "-t" ]]; then + shift + test_num $1 + test_case $1 $(get_test_count $1) $(get_test_target $1) + elif [[ "$1" = "-c" ]]; then + shift + test_num $1 + test_num $2 + test_case $1 $2 $(get_test_target $1) + elif [[ "$1" = "-s" ]]; then + shift + test_case $1 1 $(get_test_target $1) + elif [[ "$1" = "-l" ]]; then + list_tests + elif [[ "$1" = "-h" || "$1" = "--help" ]]; then + usage + else + usage + fi + fi +} + +test_reqs +allow_user_defaults +check_production_sysctl_writes_strict +load_req_mod + +trap "test_finish" EXIT + +parse_args $@ + +exit 0 |